WorldWideScience

Sample records for ferrous metallurgy committee

  1. CURRENT STATE AND TENDENCIES OF DEVELOPMENT OF FERROUS METALLURGY IN THE EAEU COUNTRIES

    Directory of Open Access Journals (Sweden)

    N. P. Dragun

    2016-01-01

    Full Text Available The analysis of modern status and tendencies of development of ferrous metallurgy in the countries of the EAEU is described in the article. On the basis of the conducted analysis are revealed the identified systemic problems of metallurgy and the conclusions on possible ways of their solution using the potential of integration are given.

  2. New alloying systems for ferrous powder metallurgy precision parts

    Directory of Open Access Journals (Sweden)

    Danninger H.

    2008-01-01

    Full Text Available Traditionally, the common alloy elements for sintered steels have been Cu and Ni. With increasing requirements towards mechanical properties, and also as a consequence of soaring prices especially for these two metals, other alloy elements have also become more and more attractive for sintered steels, which make the steels however more tricky to process through PM. Here, the chances and risks of using in particular Cr and Mn alloy steels are discussed, considering the different alloying techniques viable in powder metallurgy, and it is shown that there are specific requirements in particular for sintering process. The critical importance of chemical reactions between the metal and the atmosphere is described, and it is shown that not only O2 and H2O but also H2 and even N2 can critically affect sintering and microstructural homogenization.

  3. [The organization of the comprehensive prevention of urolithiasis among ferrous metallurgy workers].

    Science.gov (United States)

    Egorova, A M

    2009-01-01

    The purpose of study is to evaluate the effectiveness of the set of preventive measures as applied to 321 workers of basic ferrous metallurgy specialties (steel makers, mill men, hot metal shearers). During the clinical examination all the workers were divided on three groups: the workers without any pathology (11.83%, the first group), the workers with metabolic disorders only without urolitiasis (64.81%, the second group) and the workers with urolitiasis diagnosis approved by ultrasonography (23.36%, the third group). The effectiveness of rehabilitation measures was evaluated during half a year (diet therapy, drinking regimen, medicinal plants treatment). After the course of preventive measures was applied the overall health condition of most workers ameliorated and the number of workers with urolitiasis development risk factors reliably decreased up to 6-12%.

  4. Possibilities for saving energy in ferrous metallurgy: Integration of technological processes

    Directory of Open Access Journals (Sweden)

    Mihailov Emil

    2016-01-01

    Full Text Available One of the main factors having a significant effect on fuel and energy saving in the production of rolled ferrous metals is matching the operation of the continuous casting machines (CCM with that of the reheating furnaces so called “continuous technologies” in the form of “direct rolling” or “hot charging”. In order to investigate the heat exchange processes, the opportunities for enhancing the energy efficiency and determining the optimal parameters of the flat product production process in ferrous metallurgy, some mathematical models of metal solidification and cooling in a continuous steel casting machine were determined as well as a mathematical model of metal heating in the reheating furnaces. For efficient implementation of such technologies one common algorithm was built on the basis of the individual mathematical models, representing the continuous casting - rolling mill complex control technology, dynamically matching the operation of the individual units to the actual production conditions in on-line mode. The developed algorithm can be used as part of a system for analyzing the thermal condition of the blocks at any single moment for the purpose of optimization of the units’ operation within the whole technological process. As a conclusion, considering the original developed algorithm, a 21-51% energy saving was noticed.

  5. Development of structural diagram of automated dispatch control system for power consumption at non-ferrous metallurgy enterprises

    Science.gov (United States)

    Klyuev, R. V.; Bosikov, I. I.; Madaeva, M. Z.; A-V Turluev, R.

    2018-03-01

    The structural scheme of the automated control system of power consumption at the industrial enterprise is developed in the article. At the non-ferrous metallurgy enterprise, an energy inspection and a rank analysis of the electrical energy consumption of the main processing equipment were carried out. It is established that the enterprises of non-ferrous metallurgy are a complex process system consisting of a set of thousands of jointly functioning technological facilities. For the most effective estimation of power consumption of enterprises, it is reasonable to use the automated system of dispatching control of power consumption (ASDCPC). The paper presents the results of the development of the ASDCPC structural diagram that allows one to perform on-line control and management of the energy and process parameters of the main production units and the enterprise as a whole. As a result of the introduction of ASDCPC at the non-ferrous metallurgy enterprise, the consumed active power was reduced during the peak hours of the load by 20%, the specific electricity consumption - by 14%, the cost of the energy component in the cost of production of hard alloys - by 3%.

  6. Estimation of snow pollution in the region of non-ferrous metallurgy enterprises by the neutron activation method

    International Nuclear Information System (INIS)

    Khatamov, Sh.; Khamidova, R.; Kist, A.A.

    1980-01-01

    Possibility of determination of more than 25 chemical elements in snow water selected in the region of non-ferrous metallurgy enterprises has been shown using the methods of neutron activation and γ-spectrometry of high resolution. Elements were determined from one sample by three-fold irradiation in the nuclear reactor depending on the half-life period and other nuclear activation parameters of the formed radioisotopes. The analysis of snow cover has revealed the character of pollution of surrounding medium and air basin by toxical elements

  7. Metallurgical aspects of welding. Ferrous and nonferrous materials. 4. new rev. ed.; Die Metallurgie des Schweissens. Eisenwerkstoffe - nichteisenmetallische Werkstoffe

    Energy Technology Data Exchange (ETDEWEB)

    Schulze, Guenter

    2010-07-01

    This is the fourth edition of the standard work on welding metallurgy. The various problems of ferrous and nonferrous materials in the welding process are presented in great detail. In order to prevent corrosion of welded constructions, metallurgical properties and problems of all important technical materials are discussed, i.e. alloyed and unalloyed steels, cast iron materials, and the most relevant nonferrous materials. At the end of each chapter, the interested reader will find exercises for self-studies. Some of these can be solved using the material presented in the book while others are intended for deepening and further training. Easy examples (with solutions) are found all over the book; they are helpful because they provide information on underlying mechanisms and interdependences that are not obvious at first glance. The information was adapted to new EURO standards and international standards (up to March 2009) as far as these are relevant to Germany. New information is provided, e.g., on new steel standards (constructional steels according to DIN EN 10025), heat-treatable steels according to DIN EN 10025-6 and DIN EN 10083, high-alloy steels according to DIN EN 10088, and filler materials for steel welding according to DIN EN ISO 2560. The systematics of the ''law of cohabitation'' was applied to welding engineering for the first time here. (orig.) [German] Das in vierter Auflage erscheinende Buch widmet sich der Schweissmetallurgie mit ihren Besonderheiten. Die vielfaeltigen Probleme der Eisenwerkstoffe und der nichteisenmetallischen Werkstoffe bei ihrer schweisstechnischen Verarbeitung werden ausfuehrlich dargestellt. Um Korrosionsschaeden an geschweissten Konstruktionen vorzubeugen, wird die Metallurgie aller technisch bedeutsamen Werkstoffe, wie unlegierte und legierte Staehle, Eisen-Gusswerkstoffe, die wichtigsten NE-Metalle, ausfuehrlich besprochen. An den Kapitelenden findet der interessierte Leser Aufgaben, von denen ein

  8. [Factors of working environment and process on non-ferrous metallurgy enterprises in Bashkortostan Republic and workers' occupational health].

    Science.gov (United States)

    Bakirov, A B; Takaev, R M; Kondrova, N S; Shaĭkhlislamova, E R

    2011-01-01

    The authors studied factors of working environment and process on nonferrous metallurgy enterprises in Bashkortostan Republic and evaluated their influence on the workers' occupational health over 1997-2009, with consideration of occupation, sex, age, length of service, work conditions and characters. The article demonstrates that sanitary and hygienic characteristics of occupations connected with machinery operation are prone to increased integral evaluation of work conditions due to underestimation of actual hardiness and intensity of work.

  9. Metallurgy Department

    DEFF Research Database (Denmark)

    Risø National Laboratory, Roskilde

    The activities of the Metallurgy Department at Risø during 1981 are described. The work is presented in three chapters: General Materials Research, Technology and Materials Development, Fuel Elements. Furthermore, a survey is given of the department's participation in international collaboration...

  10. Implantation metallurgy

    International Nuclear Information System (INIS)

    Picraux, S.T.

    1975-01-01

    Important changes in the near-surface physical properties of metals were obtained by high-fluence ion implantation. Recently there have been an increasing number of studies of the behavior of implanted species with the aim of understanding the detailed physical processes that occur in an implanted metal layer. A key aspect of these implantation metallurgy studies has been the ability to form uniquely controlled systems in the near-surface regions of metals that can be studied with accurate depth resolution. Metallurgical parameters that may be difficult or impossible to obtain by other means can be measured. Also, parameters that depend on the implantation process, due to the athermal introduction of atoms and defects can be determined. Thus the dual objective of implantation metallurgy is to obtain information to improve understanding of the microscopic aspects of metallurgy and to understand how to form controlled new metallurgical systems. Examples of parameters studied include implanted impurity location, diffusion, enhanced diffusion, solubility, precipitation, and dissolution. (auth)

  11. Production of a low young modulus titanium alloy by powder metallurgy

    OpenAIRE

    Santos,Dalcy Roberto dos; Henriques,Vinicius André Rodrigues; Cairo,Carlos Alberto Alves; Pereira,Marcelo dos Santos

    2005-01-01

    Titanium alloys have several advantages over ferrous and non-ferrous metallic materials, such as high strengthto-weight ratio and excellent corrosion resistance. A blended elemental titanium powder metallurgy process has been developed to offer low cost commercial products. The process employs hydride-dehydride (HDH) powders as raw material. In this work, results of the Ti-35Nb alloy sintering are presented. This alloy due to its lower modulus of elasticity and high biocompatibility is a prom...

  12. Ferrous Sulfate (Iron)

    Science.gov (United States)

    ... are allergic to ferrous sulfate, any other medications tartrazine (a yellow dye in some processed foods and ... in, tightly closed, and out of reach of children. Store it at room temperature and away from ...

  13. Ferrous Metal Processing Plants

    Data.gov (United States)

    Department of Homeland Security — This map layer includes ferrous metal processing plants in the United States. The data represent commodities covered by the Minerals Information Team (MIT) of the...

  14. Metallurgy Department publications 1988

    International Nuclear Information System (INIS)

    Schroeder Pedersen, A.; Bilde-Soerensen, J.B.

    1989-08-01

    A presentation (including abstracts) of scientific and technical publications and lectures by the staff of the Metallurgy Department during 1988 is given. The list comprises journal papers, conference papers, reports, lectures and poster presentations in the following catagories: Publications, Lectures and Poster Presentations. (author)

  15. Metallurgy Department publications 1989

    International Nuclear Information System (INIS)

    Horsewell, A.

    1990-08-01

    All publiclations by the staff of the Metallurgy Department during 1989 are listed. This list is divided into three sections as follows: Publications (journal and conference papers, reports); Lectures (public lecture presentations) and Posters (poster presentations at conferences and symposia). Abstracts are included. (author)

  16. Extractive metallurgy. Recent advances

    International Nuclear Information System (INIS)

    Stevenson, E.J.

    1977-01-01

    Detailed technical information derived from patents issued since 1975 on extractive metallurgy is presented. In part one, concerning copper, the major areas covered are: smelting and roasting; acid leaching; ammonia leach processes; cuprous chloride and ferric chloride; and recovery of copper values from solution. Part two covers other metals, including: nickel and cobalt; ocean floor nodules; lead, zinc, molybdenum and manganese; precious metals; and uranium titanium, tantalum, rhenium, gallium, and other metals

  17. Current programmes of Metallurgy Division (1991)

    International Nuclear Information System (INIS)

    1991-01-01

    Current research and development programmes of the Metallurgy Division are listed under the headings: 1)Thrust Areas, 2)High Temperature Materials Section, 3)Chemical Metallurgy Section, 4)Metallurgical Thermochemistry Section, 5)Physical Metallurgy Section, 6)Mechanical Metallurgy Section, 7)Corrosion Metallurgy Section, 8)Electrochemical Science and Technology Section, 9)Ceramics Section, and 10)Fabrication and Maintenance Group. A list of equipment in the Division and a list of sciientific personnel of the Division are also given. (M.G.B.)

  18. Lithium extractive metallurgy

    International Nuclear Information System (INIS)

    Josa, J.M.; Merino, J.L.

    1985-01-01

    The Nuclear Fusion National Program depends on lithium supplies. Extractive metallurgy development is subordinate to the localization and evaluation of ore resources. Nowadays lithium raw materials usable with present technology consist of pegmatite ore and brine. The Instituto Geologico y Minero Espanol (IGME) found lepidolite, ambligonite and spodrimene in pegmatite ores in different areas of Spain. However, an evaluation of resources has not been made. Different Spanish surface and underground brines are to be sampled and analyzed. If none of these contain significant levels of lithium, the Junta de Energia Nuclear (JEN) will try an agreement with IGME for ENUSA (Empresa Nacional del Uranio, S.A.) to explore pegmatite-ore bodies from different locations. Different work stages, laboratory tests, pilots plants tests and commercial plant, are foreseen, if the deposits are found. (author)

  19. The extractive metallurgy of gold

    Energy Technology Data Exchange (ETDEWEB)

    Kongolo, K.; Mwema, M.D. [University of Lubumbashi, Zaire, Gecamines Metallurgical Research Centre, Likasi, Zaire, c/o Gecamines Brussels (Belgium)

    1998-12-15

    Moessbauer spectroscopy has been successfully used in investigation of the gold compounds present in ores and the gold species which occur during the process metallurgy of this metal. This paper is a survey of the basic recovery methods and techniques used in extractive metallurgy of gold. Process fundamentals on mineral processing, ore leaching, zinc dust cementation, adsorption on activated carbon, electrowinning and refining are examined. The recovery of gold as a by-product of the copper industry is also described. Alternative processing methods are indicated in order to shed light on new interesting research topics where Moessbauer spectroscopy could be applied.

  20. The extractive metallurgy of gold

    International Nuclear Information System (INIS)

    Kongolo, K.; Mwema, M.D.

    1998-01-01

    Moessbauer spectroscopy has been successfully used in investigation of the gold compounds present in ores and the gold species which occur during the process metallurgy of this metal. This paper is a survey of the basic recovery methods and techniques used in extractive metallurgy of gold. Process fundamentals on mineral processing, ore leaching, zinc dust cementation, adsorption on activated carbon, electrowinning and refining are examined. The recovery of gold as a by-product of the copper industry is also described. Alternative processing methods are indicated in order to shed light on new interesting research topics where Moessbauer spectroscopy could be applied

  1. Committees

    Science.gov (United States)

    2012-11-01

    Leadership Team of the IAHR Committee for Hydraulic Machinery and Systems Eduard EGUSQUIZA, UPC Barcelona, Spain, Chair François AVELLAN, EPFL-LMH, Switzerland, Past Chair Richard K FISHER, Voith Hydro Inc., USA, Past Chair Fidel ARZOLA, Edelca, Venezuela Michel COUSTON, Alstom Hydro, France Niklas DAHLBÄCKCK, Vatenfall, Sweden Normand DESY, Andritz VA TECH Hydro Ltd., Canada Chisachi KATO, University of Tokyo, Japan Andrei LIPEJ, Turboinstitut, Slovenija Torbjørn NIELSEN, NTNU, Norway Romeo SUSAN-RESIGA, 'Politehnica' University Timisoara, Romania Stefan RIEDELBAUCH, Stuggart University, Germany Albert RUPRECHT, Stuttgart University, Germany Qing-Hua SHI, Dong Fang Electrical Machinery Co., China Geraldo TIAGO, Universidade Federal de Itajubá, Brazil International Advisory Committee Shouqi YUAN (principal) Jiangsu University China QingHua SHI (principal) Dong Fang Electrical Machinery Co. China Fidel ARZOLA EDELCA Venezuela Thomas ASCHENBRENNER Voith Hydro GmbH & Co. KG Germany Anton BERGANT Litostroj Power doo Slovenia B C BHAOYAL Research & Technology Centre India Hermod BREKKE NTNU Norway Stuart COULSON Voith Hydro Inc. USA Paul COOPER Fluid Machinery Research Inc USA V A DEMIANOV Power Machines OJSC Russia Bart van ESCH Technische Universiteit Eindhoven Netherland Arno GEHRER Andritz Hydro Graz Austria Akira GOTO Ebara Corporation Japan Adiel GUINZBURG The Boeing Company USA D-H HELLMANN KSB AG Germany Ashvin HOSANGADI Combustion Research and Flow Technology USA Byung-Sun HWANG Korea Institute of Material Science Korea Toshiaki KANEMOTO Kyushu Institute of Technology Japan Mann-Eung KIM Korean Register of Shipping Korea Jiri KOUTNIK Voith Hydro GmbH & Co. KG Germany Jinkook LEE Eaton Corporation USA Young-Ho LEE Korea Maritime University Korea Woo-Seop LIM Hyosung Goodsprings Inc Korea Jun MATSUI Yokohama National University Japan Kazuyoshi Mitsubishi H I Ltd, Japan MIYAGAWA Christophe NICOLET Power Vision Engineering Srl Switzerland Maryse PAGE Hydro

  2. 21 CFR 184.1311 - Ferrous lactate.

    Science.gov (United States)

    2010-04-01

    ... prepared by reacting calcium lactate or sodium lactate with ferrous sulfate, direct reaction of lactic acid with iron filings, reaction of ferrous chloride with sodium lactate, or reaction of ferrous sulfate with ammonium lactate. (b) The ingredient meets the specifications of the Food Chemicals Codex, 4th ed...

  3. Physical metallurgy of nickel aluminides

    Indian Academy of Sciences (India)

    A description of the important physical metallurgy aspects of Ni$_3Al and NiAl encompassing structure, crystallographic defects, slip systems and phase stability has been presented in this article. The microstructures generated in the two alloys by conventional as well as novel processing techniques have been discussed.

  4. Variations of 57Fe hyperfine parameters in medicaments containing ferrous fumarate and ferrous sulfate

    International Nuclear Information System (INIS)

    Oshtrakh, M. I.; Novikov, E. G.; Dubiel, S. M.; Semionkin, V. A.

    2010-01-01

    Several commercially available medicaments containing ferrous fumarate (FeC 4 H 2 O 4 ) and ferrous sulfate (FeSO 4 ), as a source of ferrous iron, were studied using a high velocity resolution Mössbauer spectroscopy. A comparison of the 57 Fe hyperfine parameters revealed small variations for the main components in both medicaments indicating some differences in the ferrous fumarates and ferrous sulfates. It was also found that all spectra contained additional minor components probably related to ferrous and ferric impurities or to partially modified main components.

  5. Variations of {sup 57}Fe hyperfine parameters in medicaments containing ferrous fumarate and ferrous sulfate

    Energy Technology Data Exchange (ETDEWEB)

    Oshtrakh, M. I., E-mail: oshtrakh@mail.utnet.ru; Novikov, E. G. [Ural Federal University (The former Ural State Technical University-UPI), Faculty of Physical Techniques and Devices for Quality Control (Russian Federation); Dubiel, S. M. [AGH University of Science and Technology, Faculty of Physics and Computer Science (Poland); Semionkin, V. A. [Ural Federal University (The former Ural State Technical University-UPI), Faculty of Physical Techniques and Devices for Quality Control (Russian Federation)

    2010-04-15

    Several commercially available medicaments containing ferrous fumarate (FeC{sub 4}H{sub 2}O{sub 4}) and ferrous sulfate (FeSO{sub 4}), as a source of ferrous iron, were studied using a high velocity resolution Moessbauer spectroscopy. A comparison of the {sup 57}Fe hyperfine parameters revealed small variations for the main components in both medicaments indicating some differences in the ferrous fumarates and ferrous sulfates. It was also found that all spectra contained additional minor components probably related to ferrous and ferric impurities or to partially modified main components.

  6. Metallurgi for Ingeniører

    DEFF Research Database (Denmark)

    Pedersen, Jan

    Ny gennemarbejdet udgave af den klassiske "Metallurgi for Ingeniører", først skrevet af K. Offer Andersen i 1962......Ny gennemarbejdet udgave af den klassiske "Metallurgi for Ingeniører", først skrevet af K. Offer Andersen i 1962...

  7. CO2 Problems and waste recycling. Research at the Institute of ferrous metallurgy

    International Nuclear Information System (INIS)

    Gudenau, H. W.; Senk, D.; Babich, A.; Frohling, C.; Kweon, O. S.; Wang, S.; Wieting, T.

    2005-01-01

    In a short introduction tests and calculations about CO 2 -ice-blocs in the deep sea,use of CO 2 for underground-coal-gasifications and tertiary processes to increase oil-production by CO 2 -flooding are shown. New activities are presented e. g. CO 2 -injection into EAF combined with injection of coal, coke or direct reduction-fines. After research of injection of coals, fine ores or dust into blast furnaces and other shaft furnaces activities are compared with injection of hot reducing gas generated by coal or waste gasification or top gas recycling combined with injection of fine solid fuels. Results of injection of prepared plastics (Duales System Deutschland), shredder-light-fraction from car-recycling and unburned carbon of power-station-ashes are discussed. Beside production of direct-reduced-iron by H 2 fluidized reactor results of the reduction behaviour ore/coal or dust/coal pellets or briquettes for the use in rotary hearth or modern shaft furnaces are shown. (Author) 76 refs

  8. Ferrous alloy metallurgy - liquid lithium corrosion and welding. Progress report, January 1-December 31, 1980

    International Nuclear Information System (INIS)

    Olson, D.L.; Matlock, D.K.

    1980-01-01

    Fatigue crack growth has been used to evaluate the interaction between liquid lithium and an imposed stress. Fatigue crack growth data on type 304L stainless steel at 700C and 2 1/4Cr-1Mo steel between 500 and 700C show that for all imposed test conditions (i.e. frequency, temperature, and nitrogen content in the lithium) the interaction of lithium with the strain at the crack tip results in enhanced crack growth rates. The enhanced growth rates result from the effects of either enhanced grain boundary penetration or a change in crack propagation mechanism due to liquid metal embrittlement. Auger spectroscopy of grain boundary penetrated specimen shows that a lithium-oxygen compound forms at the grain boundary. Moessbauer evaluations of the ferrite layer of corroded type 304 stainless steel are being used to develop a model for weight loss in liquid lithium. The welding research in progress is directed to characterize the influence of variations of the austenitic weld metal composition on the microstructural and mechanical properties of dissimilar metal weldments. Weldments of 2 1/4Cr-1Mo steel to 316 stainless steel have been investigated for fusion microstructure, thermal expansion impact strength and characterization of specific long time in-service failures. Modification of weld metal microstructures by microalloy additions is being investigated as a concept to improve weld metal properties. The behavior of a strip electrode in a gas metal arc is being investigated to determine the feasibility of gas metal arc weld strip overlay cladding

  9. CO2 Problems and waste recycling. Research at the Institute of ferrous metallurgy

    Directory of Open Access Journals (Sweden)

    Gudenau, H. W.

    2005-04-01

    Full Text Available In a short introduction tests and calculations about CO2-ice-blocs in the deep sea, use of CO2 for underground-coal-gasification and tertiary processes to increase oil-production by C02-flooding are shown. New activities are presented e.g. CO2-injection into EAF combined with injection of coal, coke or directreduction-fines. After research of injection of coals, fine ores or dust into blast furnaces and other shaft furnaces activities are compared with injection of hot reducing gas generated by coal or waste gasification or top gas recycling combined with injection of fine solid fuels. Results of injection of prepared plastics (Duales System Deutschland, shredder-light-fraction from car-recycling and unburned carbon of power-station-ashes are discussed. Beside production of direct-reducediron by H2 fluidized reactor results of the reduction behavior ore/coal or dust/coal pellets or briquettes for the use in rotary hearth or modem shaft furnaces are shown

    En una breve introducción se describen las pruebas y cálculos referentes a bloques de hielo de CO2 en el mar profundo, el uso del CO2 para la gasificación de carbón subterráneo y procesos terciarios para aumentar la producción de aceite por medio del torrente de CO2. Dentro de las nuevas actividades se presentan, por ejemplo, la inyección de CO2 en el homo eléctrico de arco (HEA combinado con la inyección de carbón, coque o de finos de los procesos de reducción directa. Después de la investigación de la inyección de carbones, se comparan, por un lado, la inyección de los minerales finos o polvos en los hornos altos y otras actividades en los hornos de cuba con la inyección del gas reductor caliente generado por la gasificación del carbón o de los residuos o reciclado del gas del tragante combinado con la inyección de finos de combustibles sólidos. En el presente trabajo se discuten los resultados de la inyección de los plásticos preparados (Sistema Dual Alemán, de la separación de fracciones ligeras del reciclado de autos y de carbón no reaccionado de cenizas de la estación de poder. En el área de la producción de hierro reducido directamente en el reactor de lecho fluidizado de H2 son mostrados los resultados del comportamiento de la reducción de mineral con carbón o pellets de polvo con carbón o briquetas para el uso en el homo rotatorio o en modernos hornos de cuba

  10. Ferrous sulphate interacts with captopril

    Science.gov (United States)

    Schaefer, J P; Tam, Y; Hasinoff, B B; Tawfik, S; Peng, Y; Reimche, L; Campbell, N R C

    1998-01-01

    Aims To determine if iron binds strongly to captopril and reduces captopril absorption. Methods A variety of in vitro experiments was conducted to examine iron binding to captopril and a randomized, double-blind, placebo controlled, cross-over study design was used to assess the in vivo interaction. Captopril (25 mg) was coingested with either ferrous sulphate (300 mg) or placebo by seven healthy adult volunteers. Subjects were phlebotomized and had blood pressure measured at 0, 0.25, 0.5, 1, 2, 4, 6, 8, and 12 h post ingestion. A 1 week washout period was used. Results The coingestion of ferrous sulphate and captopril was associated with a 37% (134 ng ml−1 h, 95% CI 41–228 ng ml−1 h, P=0.03) decrease in area under the curve (AUC) for unconjugated plasma captopril. There were no substantial changes in Cmax (mean difference;–32; 95% CI −124–62 ng ml−1(P=0.57)) or in tmax (mean difference; 0; 95% CI −18–18 min (P=0.65)) for unconjugated captopril when captopril was ingested with iron. There was a statistically insignificant increase in AUC for total plasma captopril of 43% (1312 ng ml−1 h, 95% CI −827–3451 ng ml−1 h P=0.27) when captopril was ingested with iron. The addition of ferric chloride to captopril resulted in the initial rapid formation of a soluble blue complex which rapidly disappeared to be replaced by a white precipitant. The white precipitate was identified as captopril disulphide dimer. There were no significant differences in systolic and diastolic blood pressures between the treatment and placebo groups. Conclusions Co-administration of ferrous sulphate and iron results in decreased unconjugated captopril levels likely due to a chemical interaction between ferric ion and captopril in the gastrointestinal tract. Care is required when coprescribing captopril and iron salts. PMID:9803987

  11. The metallurgy, science and engineering

    International Nuclear Information System (INIS)

    Pineau, A.; Quere, Y.

    2011-01-01

    Metallurgy, the science of metals and the technical discipline concerned with the production, shaping and assembling of metals, is one of the major assets of European economy. The French metallurgy industry - from producers (steel, light alloys, ...) to users (car, aviation, nuclear industries, ...) -- has achieved in many of its sectors a world-class level of excellence, based on high-quality research centres that are recognized both for their theoretical and experimental academic work. By contrast, public research is insufficiently concerned with engineering. In 2004, this industry employed 1 800 000 persons, 220 000 of which worked as engineers and managers in 45 000 companies, with a turnover of 420 billion euros. This state of grace is starting to decline. We are undergoing, in this sector as in others, a de-industrialization that affects upstream activities: courses in these disciplines, which have been previously outstanding, have partially disappeared; laboratories have shrunk; expertise has been dispersed; students are staying away from a discipline they consider 'unfruitful', like many other engineering sciences. Simultaneously, further up in this sector, decision centres have moved away from production centres and away from our country. France still maintains a few important R and D centres within international groups in spite of France's decreasing weight in world production. However, these groups see the future of R and D as being centred in the emerging countries (China, India...). The main users (transport, energy, ...) are losing their experts as are the technical centres on which rely a large network of small and medium businesses. The consequences are alarming in view of the already noticeable loss of technical control. This trend can and must be reversed. Because of its presence in many industrial sectors and its excellence, metallurgy - including both research and industry - is an essential activity in which France should remain a major player

  12. Ferrous iron transport in Streptococcus mutans

    Energy Technology Data Exchange (ETDEWEB)

    Evans, S.L.; Arcenaeux, J.E.L.; Byers, B.R.; Martin, M.E.; Aranha, H.

    1986-12-01

    Radioiron uptake from /sup 59/FeCl/sub 3/ by Streptococcus mutans OMZ176 was increased by anaerobiosis, sodium ascorbate, and phenazine methosulfate (PMS), although there was a 10-min lag before PMS stimulation was evident. The reductant ascorbate may have provided ferrous iron. The PMS was reduced by the cells, and the reduced PMS then may have generated ferrous iron for transport; reduced PMS also may have depleted dissolved oxygen. It was concluded that S. mutans transports only ferrous iron, utilizing reductants furnished by glucose metabolism to reduce iron prior to its uptake.

  13. Iron in ferrous gluconate and Ascofer (registered)

    Energy Technology Data Exchange (ETDEWEB)

    Gozdyra, R; Dubiel, S M; Cieslak, J, E-mail: dubiel@novell.ftj.agh.edu.p [Faculty of Physics and Computer Science, AGH University of Science and Technology, al. A. Mickiewicza 30, PL-30-059 Krakow (Poland)

    2010-03-01

    Ferrous gluconate and antianemic medicament Ascofer (registered) were investigated with Moessbauer spectroscopy in order to determine forms of iron ions present in both types of samples. Room temperature spectra gave a clear evidence that two phases of iron were present viz. ferrous (Fe{sup 2+}) as a major one with a contribution of {approx}85 {+-}5 %, and ferric (Fe{sup 3+}) whose contribution was found to be {approx}15{+-}5 %. Ferrous ions were shown to occupy at least two different sites.

  14. Progress report of the Metallurgy Group

    International Nuclear Information System (INIS)

    Sundaram, C.V.; Moorthy, V.K.

    1975-01-01

    The activities of the Metallurgy Division of the Bhabha Atomic Research Centre, Bombay, during the year 1974 are reported under six sections, namely: ore dressing; extractive metallurgy; ceramics; physical metallurgy; corrosion and electrometallurgy, and radiometallurgy. The developmental programme is not only concerned with materials of nuclear interest such as uranium, thorium, plutonium, zirconium, niobium and beryllium, but also other materials of national interest such as titanium, tantalum, ceramics, corrosion-resistant alloys etc. In addition to the laboratory studies, collaborative work has also been undertaken with other units of the Department of Atomic Energy. (A.K.)

  15. Self-Paced Tutorial Courses for Mineral Science - Metallurgy Departments. Final Progress Report (July 1975-August 1980).

    Science.gov (United States)

    Twidwell, L. G.

    Four courses in extractive metallurgy (Pyrometallurgy, Hydrometallurgy, Electrometallurgy; and Physical Chemistry of Iron and Steel) were prepared in a modular, self-paced format. Development of the course materials included: (1) preparation of course outlines by unit coordinators and advisory committees; (2) approval of course outlines (included…

  16. [Respiratory diseases in metallurgy production workers].

    Science.gov (United States)

    Shliapnikov, D M; Vlasova, E M; Ponomareva, T A

    2012-01-01

    The authors identified features of respiratory diseases in workers of various metallurgy workshops. Cause-effect relationships are defined between occupational risk factors and respiratory diseases, with determining the affection level.

  17. Structural Description of Powder Metallurgy Prepared Materials

    Czech Academy of Sciences Publication Activity Database

    Michalcová, A.; Vojtěch, D.; Kubatík, Tomáš František; Novák, P.; Dvořák, P.

    2014-01-01

    Roč. 14, č. 3 (2014), s. 359-362 ISSN 1213-2489. [Mezinárodní konference „Mikroskopie a nedestruktivní zkoušení materiálů/3./. Litoměřice, 22.10.2014-24.10.2014] Institutional support: RVO:61389021 Keywords : SPS * Intermetallics * powder metallurgy Subject RIV: JG - Metallurgy http://journal.strojirenskatechnologie.cz/templates/obalky_casopis/XIV_2014-3.pdf

  18. Advanced powder metallurgy aluminum alloys and composites

    Science.gov (United States)

    Lisagor, W. B.; Stein, B. A.

    1982-01-01

    The differences between powder and ingot metallurgy processing of aluminum alloys are outlined. The potential payoff in the use of advanced powder metallurgy (PM) aluminum alloys in future transport aircraft is indicated. The national program to bring this technology to commercial fruition and the NASA Langley Research Center role in this program are briefly outlined. Some initial results of research in 2000-series PM alloys and composites that highlight the property improvements possible are given.

  19. Fast and effective analysis of ferrous and non-ferrous alloys by X-ray fluorescence

    International Nuclear Information System (INIS)

    Gomez Serra, Abelardo

    1987-01-01

    An empirical method for the integral analysis of any kind of alloys, ferrous and non-ferrous, is described. The method is based on the intensities relation of the mixed elements and is independent of the size, shape and presentation of the sample. By this procedure, alloys with iron, copper, aluminium or magnesium base can be fastly classified. (S.M.) [es

  20. Powder metallurgy development at SRL

    International Nuclear Information System (INIS)

    Peacock, H.B.

    1978-01-01

    Fuel for Savannah River Plant (SRP) reactors consists of extruded tubes with aluminum--uranium alloy cores clad with 8001 aluminum. The 235 U in the fuel is periodically recovered and recycled in new fuel assemblies. The buildup of 236 U in the enriched uranium requires increased total uranium contents to maintain reactivity in existing assembly designs. High level waste production from these tubes is proportional to the aluminum content; therefore, appreciable radioactive waste reductions result from lower aluminum--uranium ratios and thinner clad tubes. The casting process now used for fuel cores is limited to below 40 wt % U because of the reduced fabricability of high uranium alloys. To increase tube loading and reduce aluminum, the U 3 O 8 -Al powder metallurgy (P/M) process for fuel tubes is under development. Several fabricaion and irradiaion tests have been made using production conditions. Both small scale and production tests carried out at SRL for high-density P/M fuel development are discussed

  1. Current programmes on physical metallurgy and related areas in BARC

    International Nuclear Information System (INIS)

    1994-01-01

    Current research and development programmes on physical metallurgy and related areas from the following Divisions of Bhabha Atomic Research Centre are included in this report : Atomic Fuels Division, High Pressure Physics Division, Metallurgy Division, Radio Metallurgy Division, Solid State Physics Division. Important publications corresponding to each activity have also been listed. (author)

  2. Ideate about building green mine of uranium mining and metallurgy

    International Nuclear Information System (INIS)

    Shi Zuyuan

    2012-01-01

    Analysing the current situation of uranium mining and metallurgy; Setting up goals for green uranium mining and metallurgy, its fundamental conditions, Contents and measures. Putting forward an idea to combine green uranium mining and metallurgy with the state target for green mining, and keeping its own characteristics. (author)

  3. New evidence for prehistoric copper metallurgy in the vicinity of Bor

    Directory of Open Access Journals (Sweden)

    Kapuran Aleksandar

    2016-01-01

    Full Text Available The last three years of archaeological investigations at the site Ru`ana in Banjsko Polje, in the immediate vicinity of Bor, have provided new evidence regarding the role of non-ferrous metallurgy in the economy of the prehistoric communities of north-eastern Serbia. The remains of metallurgical furnaces and a large amount of metallic slags at two neighbouring sites in the mentioned settlement reveal that locations with many installations for the thermal processing of copper ore existed in the Bronze Age. We believe, judging by the finds of material culture, that metallurgical activities in this area also continued into the Iron Age and, possibly, into the 4th century AD. [Projekat Ministarstva nauke Republike Srbije, br. 177020: Archaeology of Serbia: Cultural identity, integration factors, technological processes and the role of the central Balkans in the development of European prehistory

  4. Powder metallurgy development at SRL

    International Nuclear Information System (INIS)

    Peacock, H.B.

    1993-01-01

    The Savannah River Laboratory (SRL) is developing a powder metallurgy (P/M) process for manufacturing reactor-grade fuel tubes containing high wt % U 3 O 8 -Al cores clad with 8001 aluminum. The P/M cores are made by isostatic compaction. They are assembled in billets, outgassed, and hot-extruded using conventional coextrusion techniques. Cores have been compacted with up to 100% U3O 8 and tubes extruded with 80 wt % oxide cores. Irradiation tests have been made using P/M core tubes in the Savannah River reactors. These tubes contained U 3 O 8 concentrations up to 59 wt % and no significant swelling or blistering occurred. The tubes were irradiated to ∼ 40% burnup or 1.6x10 21 fissions/cc of core. This report discusses both small-scale and production tests for high-density P/M fuel development. The purpose of the P/M development program at SRL is to: determine the maximum U 3 O 8 content that can be fabricated into thin wall tubes, irradiate high-density tubes to high burnup and assess irradiation and dimensional stability, continue metal forming studies for extrusion and drawing, and evaluate hydrostatic extrusion and hydrostatically assisted drawing of P/M core tubes. Experimental results of testing the fuel assemblies performance so far indicate that: cores containing fine (-325 mesh) U 3 O 8 and aluminum powders can be made practically free of high-density areas using the outlined P/M pre blending and sieving techniques. U 3 O 8 -Al cores can be isostatically compacted with up to 100 wt U 3 O 8 and tubes successfully extruded with up to 80 wt oxide; fission gas blistering of U 3 O 8 -Al P/M tubes as indicated by the blister tests is a function of fissions/cc of U 3 O 8 in the core; Decreasing the fission density of oxide increases the threshold temperature for blister formation; U 3 O 8 -Al P/M fuel tubes with up to 59 wt U 3 O 8 have been successfully irradiated in SRP reactor to 1.6 x 10 21 fissions/cc of core or 7 x 10 20 fissions/cc of U 3 O 8 small

  5. Bacterial ferrous iron transport: the Feo system.

    Science.gov (United States)

    Lau, Cheryl K Y; Krewulak, Karla D; Vogel, Hans J

    2016-03-01

    To maintain iron homeostasis within the cell, bacteria have evolved various types of iron acquisition systems. Ferric iron (Fe(3+)) is the dominant species in an oxygenated environment, while ferrous iron (Fe(2+)) is more abundant under anaerobic conditions or at low pH. For organisms that must combat oxygen limitation for their everyday survival, pathways for the uptake of ferrous iron are essential. Several bacterial ferrous iron transport systems have been described; however, only the Feo system appears to be widely distributed and is exclusively dedicated to the transport of iron. In recent years, many studies have explored the role of the FeoB and FeoA proteins in ferrous iron transport and their contribution toward bacterial virulence. The three-dimensional structures for the Feo proteins have recently been determined and provide insight into the molecular details of the transport system. A highly select group of bacteria also express the FeoC protein from the same operon. This review will provide a comprehensive look at the structural and functional aspects of the Feo system. In addition, bioinformatics analyses of the feo operon and the Feo proteins have been performed to complement our understanding of this ubiquitous bacterial uptake system, providing a new outlook for future studies. © FEMS 2015. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

  6. Biennial activity report of metallurgy programme for 1987 and 1988

    International Nuclear Information System (INIS)

    Shanmugam, V.; Rao, B.P.C.; Bhanu Sankara Rao, K.; Muralidharan, P.; Bhaduri, A.K.; Kuppusami, P.; Shyamsunder, M.T.; Sampath, N.; Sreedharan, O.M.

    1990-01-01

    The research and development (R and D) activities in the field of metallurgy at Indira Gandhi Centre for Atomic Research, Kalpakkam during 1987-1988 are reported in the form of individual summaries arranged under headings : (1) Mechanical Metallurgy Section, (2) Physical Metallurgy Section, (3) Chemical Metallurgy Section, (4) Materials Technology Section, (5) Division for PIE and NDT Development and (6) Quality Engineering Section. A list of publications by the staff scientists working in the field of metallurgy during report period is given in one of the appendices. (author). figs., tabs

  7. Metallurgy department publications and lectures 1987

    International Nuclear Information System (INIS)

    Schroeder Pedersen, A.; Bilde-Soerensen, J.B.

    1988-04-01

    A presentation (including abstract) of scientific and technical publications and lectures by the staff of the Metallurgy Department during 1987 is given. The list comprises journal papers, conference papers, reports, lectures and poster presentations in the following categories: Publications, Lectures and Poster Presentations. (author)

  8. Investigations to problems of the implantation metallurgy

    International Nuclear Information System (INIS)

    Rauschenbach, B.

    1987-01-01

    Basing on processes and effects caused ion implantation of metals a review is given about the problems of the implantation metallurgy. Techniques of high-fluence ion implantation and ion beam mixing are generally confined. These techniques change the structure and the chemical composition in the near of the surface of metals. The application of these methods is demonstrated on series of examples. (author)

  9. Powder-Metallurgy Process And Product

    Science.gov (United States)

    Paris, Henry G.

    1988-01-01

    Rapid-solidification processing yields alloys with improved properties. Study undertaken to extend favorable property combinations of I/M 2XXX alloys through recently developed technique of rapid-solidification processing using powder metallurgy(P/M). Rapid-solidification processing involves impingement of molten metal stream onto rapidly-spinning chill block or through gas medium using gas atomization technique.

  10. Development and prospect of china uranium mining and metallurgy

    International Nuclear Information System (INIS)

    Que Weimin; Wang Haifeng; Niu Yuqing; Gu Wancheng; Zhang Feifeng

    2007-01-01

    The development of industry of uranium mining and metallurgy in China has been reviewed generally, emphasizing on investigation approaches and application levels of uranium mining technologies such as in-situ leaching, heap leaching, stope leaching: on the basis of analysis on status of uranium mining and metallurgy and problems existed, also considering the specific features of deposit resources, the development orientation of uranium mining and metallurgy in China is pointed out. The industry of China uranium mining and metallurgy is faced to new opportunity of development and challenge in 21st century, the only way to realize sustainable development of uranium mining and metallurgy and harmonious development between economy and environment is to develop new technology on mining, ore beneficiation and metallurgy, increase the utilization level of uranium resources, low down impact on environment caused by mining and metallurgy. (authors)

  11. Production of a low young modulus titanium alloy by powder metallurgy

    Directory of Open Access Journals (Sweden)

    Dalcy Roberto dos Santos

    2005-12-01

    Full Text Available Titanium alloys have several advantages over ferrous and non-ferrous metallic materials, such as high strengthto-weight ratio and excellent corrosion resistance. A blended elemental titanium powder metallurgy process has been developed to offer low cost commercial products. The process employs hydride-dehydride (HDH powders as raw material. In this work, results of the Ti-35Nb alloy sintering are presented. This alloy due to its lower modulus of elasticity and high biocompatibility is a promising candidate for aerospace and medical use. Samples were produced by mixing of initial metallic powders followed by uniaxial and cold isostatic pressing with subsequent densification by isochronal sintering between 900 up to 1600 °C, in vacuum. Sintering behavior was studied by means of microscopy and density. Sintered samples were characterized for phase composition, microstructure and microhardness by X-ray diffraction, scanning electron microscopy and Vickers indentation, respectively. Samples sintered at high temperatures display a fine plate-like alpha structure and intergranular beta. A few remaining pores are still found and density above 90% for specimens sintered in temperatures over 1500 °C is reached.

  12. Semi Automated Ferrous Material Scouring System (SAFMSS)

    Science.gov (United States)

    2016-03-14

    During normal activity, the operator needs to interrupt the operation periodically to dump the load of ferrous material. Once the operator...various targets used over the years including scraps from 55 gallon barrels, old cars and trucks as well as unidentifiable sources. Figure 8: Aerial...what the system uncovered the team surmised it was used mostly as a dump site for a mess hall. The Dona Ana range complex has been used by the army

  13. Passive Aerial Grasping of Ferrous Objects

    KAUST Repository

    Fiaz, Usman Amin

    2017-10-19

    Aerial transportation is probably the most efficient way to supply quick and effective aid especially in cases of emergency like search and rescue operations. Thus the ability to grasp and deliver objects is of vital importance in all sorts of unmanned and autonomous aerial operations. We detail a simple yet novel approach for aerial grasping of ferrous objects using a passive magnetic pickup and an impulse based drop mechanism. The design enables our gripper to grasp ferrous objects using single as well as multiple gripping pads, with visual as well as pickup and drop feedback. We describe the various components of the gripper with emphasis on its low mass and high lift capability since weight is a matter of high consideration in all aerial applications. In addition, we investigate and address the issues that may cause our design to fail. We demonstrate by experiments that the proposed design is robust and effective, based on its high payload capability, its sturdiness against possible slide during aggressive aerial maneuvers, and optimum performance of the drop mechanism for the designed range of payloads. We also show that the gripper is able to pick up and drop a single as well as multiple ferrous objects of different shapes, curvature, and inclination, which also involves picking up an object and then grasping the next, while keeping hold of the previous one.

  14. Computational thermodynamics in electric current metallurgy

    DEFF Research Database (Denmark)

    Bhowmik, Arghya; Qin, R.S.

    2015-01-01

    A priori derivation for the extra free energy caused by the passing electric current in metal is presented. The analytical expression and its discrete format in support of the numerical calculation of thermodynamics in electric current metallurgy have been developed. This enables the calculation...... of electric current distribution, current induced temperature distribution and free energy sequence of various phase transitions in multiphase materials. The work is particularly suitable for the study of magnetic materials that contain various magnetic phases. The latter has not been considered in literature....... The method has been validated against the analytical solution of current distribution and experimental observation of microstructure evolution. It provides a basis for the design, prediction and implementation of the electric current metallurgy. The applicability of the theory is discussed in the derivations....

  15. Powder metallurgy bearings for advanced rocket engines

    Science.gov (United States)

    Fleck, J. N.; Killman, B. J.; Munson, H.E.

    1985-01-01

    Traditional ingot metallurgy was pushed to the limit for many demanding applications including antifriction bearings. New systems require corrosion resistance, better fatigue resistance, and higher toughness. With conventional processing, increasing the alloying level to achieve corrosion resistance results in a decrease in other properties such as toughness. Advanced powder metallurgy affords a viable solution to this problem. During powder manufacture, the individual particle solidifies very rapidly; as a consequence, the primary carbides are very small and uniformly distributed. When properly consolidated, this uniform structure is preserved while generating a fully dense product. Element tests including rolling contact fatigue, hot hardness, wear, fracture toughness, and corrosion resistance are underway on eleven candidate P/M bearing alloys and results are compared with those for wrought 440C steel, the current SSME bearing material. Several materials which offer the promise of a significant improvement in performance were identified.

  16. Metallurgy Department. Annual progress report for 1989

    International Nuclear Information System (INIS)

    Horsewell, A.; Hansen, N.

    1990-07-01

    Selected activities of the Metallurgy Department at Risoe National Laboratory during 1989 are described. The work is presented in three chapters: Materials Science, Materials Engineering and Materials Technology. A survey is given of the Department's participation in international collaboration and of its acitivities within eduation and training. Furthermore, the main figures outlining the funding and expenditure of the Department are given. Lists of staff members, visiting scientists, publicaltions, lectures and poster presentations are included. (author) 90 refs

  17. Metallurgy Department annual progress report for 1987

    International Nuclear Information System (INIS)

    Schroeder Pedersen, A.; Bilde-Soerensen, J.B.; Hansen, N.

    1988-05-01

    Selected activities of the Metallurgy Department at Risoe National Laboratory during 1987 are described. The work is presented in four chapters: Materials Science, Materials Engineering, Materials Technology and Energy Programmes. A survey is given of the Department's participation in international collaboration and of its activities within education and training. Furthermore, the main numbers illustrating the Departments's economy are given. Lists of staff members, visiting scientists, publications, lectures and poster presentations are included. 38 ills. (author)

  18. Metallurgy Department. Annual progress report for 1988

    International Nuclear Information System (INIS)

    Schroeder Pedersen, A.; Bilde-Soerensen, J.B.; Hansen, N.

    1989-05-01

    Selected activities of the Metallurgy Department at Risoe National Laboratory during 1988 are described. The work is presented in four chapters: Materials Science, Materials Engineering, Materials Technology and Energy Programmes. A survey is given of the Department's participation in international collaboration and of its activities within education and training. Furthermore, the main numbers illustrating the Department's economy are given. Lists of staff members, visiting scientists, publications, lectures and poster presentations are included. (author) 36 ills., 81 refs

  19. NON-FERROUS EXPORTS CONCENTRATION AND GLOBAL INVESTMENTS

    OpenAIRE

    Brîndușa COVACI

    2016-01-01

    In the context of high-tech and telecommunication, non-ferrous sector has a crucial role in industries development. Cooper, nickel, aluminum, zinc, lead and tin are used, directly or indirectly, in most of the technologies, especially in high-tech production. The paper present a short index of the global investments for the non-ferrous transnational corporations listed on London Metal Exchange. The non-ferrous investment index presented in the paper refers to the most profitable corporation e...

  20. Thermally activated martensite formation in ferrous alloys

    DEFF Research Database (Denmark)

    Villa, Matteo; Somers, Marcel A. J.

    2017-01-01

    Magnetometry was applied to investigate the formation of α/α´martensite in 13ferrous alloys during immersion in boiling nitrogen and during re-heating to room temperature at controlled heating rates in the range 0.0083-0.83 K s-1. Data showsthat in 3 of the alloys, those that form {5 5 7}γ...... martensite, no martensite developsduring cooling. For all investigated alloys, irrespective of the type of martensiteforming, thermally activated martensite develops during heating. The activationenergy for thermally activated martensite formation is in the range 8‒27 kJ mol-1and increases with the fraction...... of interstitial solutes in the alloy...

  1. Low-Cobalt Powder-Metallurgy Superalloy

    Science.gov (United States)

    Harf, F. H.

    1986-01-01

    Highly-stressed jet-engine parts made with less cobalt. Udimet 700* (or equivalent) is common nickel-based superalloy used in hot sections of jet engines for many years. This alloy, while normally used in wrought condition, also gas-atomized into prealloyed powder-metallurgy (PM) product. Product can be consolidated by hot isostatically pressing (HIPPM condition) and formed into parts such as turbine disk. Such jet-engine disks "see" both high stresses and temperatures to 1,400 degrees F (760 degrees C).

  2. Borax as a lubricant in powder metallurgy

    Directory of Open Access Journals (Sweden)

    Héctor Geovanny Ariza-Suarez

    2014-12-01

    were compacted at 700 MPa in a uniaxial press of 15 tons. DSC-TGA analysis of the mixture with borax was realized. The specimens were sintered in a plasma reactor at 1000 for 30 minutes, with a combined atmosphere of hydrogen and argon. Microhardness and density of the sintered samples was haracterized. XRD analysis was realized to detect possible compounds formation by interaction of borax. This paper shows that borax can be used as a lubricant in powder metallurgy.

  3. Biaxially textured articles formed by powder metallurgy

    Science.gov (United States)

    Goyal, Amit; Williams, Robert K.; Kroeger, Donald M.

    2003-07-29

    A biaxially textured alloy article having a magnetism less than pure Ni includes a rolled and annealed compacted and sintered powder-metallurgy preform article, the preform article having been formed from a powder mixture selected from the group of mixtures consisting of: at least 60 at % Ni powder and at least one of Cr powder, W powder, V powder, Mo powder, Cu powder, Al powder, Ce powder, YSZ powder, Y powder, Mg powder, and RE powder; the article having a fine and homogeneous grain structure; and having a dominant cube oriented {100} orientation texture; and further having a Curie temperature less than that of pure Ni.

  4. Biaxially textured articles formed by power metallurgy

    Science.gov (United States)

    Goyal, Amit; Williams, Robert K.; Kroeger, Donald M.

    2003-08-26

    A biaxially textured alloy article having a magnetism less than pure Ni includes a rolled and annealed compacted and sintered powder-metallurgy preform article, the preform article having been formed from a powder mixture selected from the group of mixtures consisting of: at least 60 at % Ni powder and at least one of Cr powder, W powder, V powder, Mo powder, Cu powder, Al powder, Ce powder, YSZ powder, Y powder, Mg powder, and RE powder; the article having a fine and homogeneous grain structure; and having a dominant cube oriented {100} orientation texture; and further having a Curie temperature less than that of pure Ni.

  5. Preparation of nitinol by non-conventional powder metallurgy techniques

    Czech Academy of Sciences Publication Activity Database

    Novák, P.; Moravec, H.; Salvetr, P.; Průša, F.; Drahokoupil, Jan; Kopeček, Jaromír; Karlík, M.; Kubatík, Tomáš František

    2015-01-01

    Roč. 31, č. 15 (2015), s. 1886-1893 ISSN 0267-0836 R&D Projects: GA ČR(CZ) GA14-03044S Institutional support: RVO:68378271 ; RVO:61389021 Keywords : shape memory alloys * SHS process * SEM * powder metallurgy Subject RIV: JG - Metallurgy Impact factor: 1.008, year: 2015

  6. Metallurgy and Heat Treating. Welding Module 7. Instructor's Guide.

    Science.gov (United States)

    Missouri Univ., Columbia. Instructional Materials Lab.

    This guide is intended to assist vocational educators in teaching a three-unit module in metallurgy and heat treating. The module is part of a welding curriculum that has been designed to be totally integrated with Missouri's Vocational Instruction Management System. The basic principles of metallurgy and heat treatment and techniques for…

  7. Evaluation of iron transport from ferrous glycinate liposomes using ...

    African Journals Online (AJOL)

    2017-09-03

    Sep 3, 2017 ... the effects of liposomal carriers, phytic acid, zinc and particle size on iron transport using Caco-2 cell models. Methods: Caco-2 cells were .... port of ferrous glycinate liposomes could result from the protection of ferrous glycinate by ..... 1998;37:12875-12883. 23. Albanese A, Tang PS, Chan WC The effect of.

  8. NON-FERROUS EXPORTS CONCENTRATION AND GLOBAL INVESTMENTS

    Directory of Open Access Journals (Sweden)

    Brîndușa COVACI

    2016-12-01

    Full Text Available In the context of high-tech and telecommunication, non-ferrous sector has a crucial role in industries development. Cooper, nickel, aluminum, zinc, lead and tin are used, directly or indirectly, in most of the technologies, especially in high-tech production. The paper present a short index of the global investments for the non-ferrous transnational corporations listed on London Metal Exchange. The non-ferrous investment index presented in the paper refers to the most profitable corporation exports on world, European Union (EU28 and Central and Eastern Europe (CEE level. The export concentration, estimated through Herfindahl-Hirschmann index on world, EU28, CEE and Romanian level, show that the non-ferrous industry is in full process of releasing. The cases presented in the article show that the non-ferrous companies invest intensively in equipment and technologies with superior production capacities, which combat pollution given by non-ferrous processes, research and development for the non-ferrous innovative technologies, and creating new markets. Sustainable and intelligent development is the inflexion point of the non-ferrous transnational corporation investments. The research is predominant in exploration of the transnational corporations’ internet pages and reports, and statistical calculus from international trade websites.

  9. Titanium surgical implants processed by powder metallurgy

    Energy Technology Data Exchange (ETDEWEB)

    Oliveira, M.V. de [INT-DMCM, Inst. Nacional de Tecnologia, Rio de Janeiro, RJ (Brazil); Pereira, L.C. [Programa de Eng. de Materiais e Metalurgica, UFRJ-COPPE (Brazil); Schwanke, C.M.; Schaeffer, L. [Centro de Tecnologia- LdTM-INT-DMCM, UFRGS, Venezuela, CEP, Rio de Janeiro, RJ (Brazil)

    2001-07-01

    Due to their low density coupled with excellent corrosion resistance and good mechanical properties, titanium and titanium alloys have been widely used for surgical implants. They have also a relatively low young's modulus, allowing a good load transfer to the bone. The elastic modulus difference between metallic implant material and bone is large, which can lead to a fracture of the implant. To solve this problem, many implants for artificial joint and dental applications have been produced by powder metallurgy routes, obtaining a porous material with an even lower young's modulus than that of the bulk titanium. This porous structure allows bone ingrowth, as the osseous tissue invade the holes of the porous material while growing and adheres to it. Besides, near net shape technologies like powder metallurgy and injection molding techniques, can reduce the components high costs due to machining final steps, also providing a fine, uniform grain structure and lack of texture and segregation. This work outlines the characteristics, properties and some of the powder routes for producing titanium surgical implants and implant porous coatings. (orig.)

  10. Promoting energy conservation in China's metallurgy industry

    International Nuclear Information System (INIS)

    Lin, Boqiang; Du, Zhili

    2017-01-01

    China is undergoing rapid industrialization and urbanization, with consequent dramatic increase in energy demand. Given energy scarcity, environmental pollution, energy security and energy cost constraints, energy conservation will be the major strategy in China's transition to a low-carbon economy. Since the metallurgy industry is a main sector of energy consumption, the efficiency of energy conservation in this industry will affect the future prospects of energy savings. This paper analyzes the energy conservation potential of China's metallurgy industry. First, seemingly unrelated regression method is applied to investigate the relationship between energy relative price, R&D input, enterprise ownership structure, enterprise scale and energy intensity of the metallurgy industry. Then, based on the SUR results, we use the scenario analysis method to predict energy consumption and savings potential in the industry in different scenarios. This paper provides references for China's government and metallurgy industry in formulating relevant energy conservation policies. - Highlights: • Seemingly unrelated regression method is applied to analyze the energy intensity of metallurgy industry. • We use the scenario analysis method to predict energy consuming and energy saving of Chinese metallurgy industry. • Provide references for China's government and metallurgy industry in formulating relevant energy conservation policies.

  11. Biennial activity report of Metallurgy Division for 1989 and 1990

    International Nuclear Information System (INIS)

    Kamachi Mudali, U.; Muraleedharan, P.; Parameswaran, P.; Swaminathan, K.; Sreedharan, O.M.

    1993-01-01

    This is the first divisional biennial report of the Metallurgy Division of Indira Gandhi Centre for Atomic Research, for the year 1989-1990, after formation of the Metallurgy Division in September 1988. Major areas of work in the Division relate to aqueous corrosion and localised corrosion, stress corrosion cracking and liquid metal corrosion, high temperature oxidation, thermodynamic studies, physical metallurgy studies for structure-property correlations and failure analyses. The principal materials of studies have been the austenitic stainless steels, the current materials of construction in the Fast Breeder Test Reactor and the candidate materials for the Prototype Fast Breeder Reactor

  12. Chemistry and metallurgy in the Portuguese Empire

    Energy Technology Data Exchange (ETDEWEB)

    Habashi, F. [Laval Univ., Sainte-Foy, Quebec City, PQ (Canada)

    2000-10-01

    The foundation and expansion of the Portuguese Empire is sketched, with emphasis on the development of a new type of ship by Prince Henrique the Navigator (AD 1385-1460), known as the caravel. By virtue of its advanced design, it was capable of sailing the stormy seas at high speeds, and thereby was instrumental in extending Portuguese influence over vast territories in South America, Asia and Africa, extending Portuguese know-how in mining, metallurgy, chemistry and trade along with Christianity. The role played by the University of Coimbra, founded in 1306, and the contribution of the Brazilian Geological Survey, established in 1875, and of the School of Mines in Ouro Preto in Brazil in 1876, in the exploitation of the mineral wealth of the Portuguese colonies is chronicled.

  13. Adsorption of ferrous ions onto montmorillonites

    Energy Technology Data Exchange (ETDEWEB)

    Qin, Dawei, E-mail: qdw109@163.com [Qilu University of Technology, Jinan, 250353, Shandong (China); Niu, Xia [Qilu University of Technology, Jinan, 250353, Shandong (China); Qiao, Min; Liu, Gang; Li, Hongxin; Meng, Zhenxiao [Shandong SiBang pharmaceutical co., LTD, Jinan, Shandong, 250200 (China)

    2015-04-01

    Highlights: • Adsorption study of ferrous ions on montmorillonites. • Using ascorbic acid as antioxidants in adsorption process. • Fe (II)-MMT had good affinity for phosphate. - Abstract: The adsorption of Fe (II) onto montmorillonites was investigated through initial concentration, contact time, pH and temperature. During the whole adsorption process, the ascorbic acid (Vitamin C) was added as a kind of antioxidant, at the same time, deionized water (after boiling) and nitrogen protection were also used to avoid oxidation. The Fe{sup 2+}/Fe{sub total} ratio of the iron exists in the Fe-montmorillonites was found more than 95%. Two kinetic models, including pseudo-first-order and pseudo-second-order model, were used to analyze the adsorption process of Fe (II) on montmorillonites. The results of our study showed that adsorption process fitted with pseudo-second-order well. Adsorption isotherms showed that Langmuir model was better than Freundlich model. The thermodynamic parameters ΔG{sup 0} and ΔH{sup 0} were 3.696 kJ/mol and 6.689 kJ/mol (we just gave the values at 298 K), respectively. The positive values at different temperatures showed that the adsorption process was non-spontaneous and endothermic. The characteristics of materials were determined by X-ray diffraction (XRD), Fourier transform infrared (FT-IR), Surface area and porosity analyzer, Thermogravimetric analysis (TGA), Differential scanning calorimeter (DSC) and Zeta potential distribution.

  14. Thermogravimetric control of intermediate compounds in uranium metallurgy

    International Nuclear Information System (INIS)

    Gasco Sanchez, L.; Fernandez Cellini, R.

    1959-01-01

    The thermal decomposition of some intermediate compounds in the metallurgy of the uranium as uranium peroxide, ammonium uranate, uranium and ammonium penta-fluoride, uranium tetrafluoride and uranous oxide has been study by means of the Chevenard's thermo balance. Some data on pyrolysis of synthetic mixtures of intermediate compounds which may occasionally appear during the industrial process, are given. Thermogravimetric methods of control are suggested, usable in interesting products in the uranium metallurgy. (Author) 20 refs

  15. Application of tracer techniques and technical means in ferrous, non-ferrous and hydrometallurgy

    International Nuclear Information System (INIS)

    Chizhek, L.; Myshak, F.; Shtrba, J.

    1979-01-01

    Brief data are given about the results of joint investigations and developments of the problems of radioisotope methods and technical means application in ferrous and hydrometallurgy, obtained during the period of 1976-1977. Development of these problems was done in the frameworks of the plan of scientific and technical cooperation of the CMEA member-states and Yugoslavia. Results are given of the development of following themes: investigation of metallurgic processes by means of activation analysis; investidations of metallurgic processes by means of autoradiography and X-ray feuorescent analysis; control and automatization of metallurgic processes by means of radioisotope instruments; investigation of processes of melting of cast iron and steel as well as of processes of treatment of metals by means of the radioactive indicators method, activation analysis and radioisotope instruments; application of the radioisotope methods and technical means for investigation of processes of production of non-ferrous metals; application of the radioisotope methods for investigations of the hydrometallurgy processes [ru

  16. Sensory evaluation of dairy supplements enriched with reduced iron, ferrous sulfate or ferrous fumarate

    Directory of Open Access Journals (Sweden)

    Josefina C Morales

    2015-01-01

    Full Text Available Objective. To determine the degree of liking of the Oportunidades programme dietary supplements (DS –purees and beverages– added with different iron salts (IS: reduced iron (RI, ferrous sulphate (FS or ferrous fumarate (FF during 24 weeks of storage. Materials and methods. The DS were evaluated through a hedonic scale for aroma, flavour and colour attributes; at time zero and every eight weeks, each panel member evaluated three DS with same flavour and presentation but different IS. Seventy women participated as panel members. Results. The chocolate and banana DS exhibited a change in preference by colour and flavour due to storage. DS with FS or RI showed the least preference by flavour and colour in the context of the three IS considered. The chocolate and neutral DS enriched with FS changed their colour and flavour. Conclusion. DS were, in general, well-liked; nonetheless, for purees enriched with FS and for beverages enriched with RI, the less-liked attributes were colour and flavour

  17. The metallurgy of superalloys part 2

    International Nuclear Information System (INIS)

    Abdelazim, M.E.; Hammad, F.H.

    1990-01-01

    This is part II of the report titled 'the metallurgy of superalloys'. It deals with the effect of heat treatment and operating conditions (thermal exposure and environment) on the mechanical properties of superalloys. The heat treatment is important in the development of superalloys through that it controls type, amount, size shape and distribution of the precipitate and the grain size of the matrix. The thermal exposure leads to reduction in the amount of the primary carbides and to precipitation of secondary carbides. Also it leads to the agglomeration and coarsening of gamma or the transformation of gamma phase to phase. The environment may lead to the internal oxidation, carburization, decarburization or sulphidization of the superalloys which may result in the degradation of their mechanical properties. This part gives also an example of applications of superalloys in the field of nuclear reactors especially high temperature-gas cooled reactors. Joined with this part a table which contains the major superalloys including its chemical analysis, creep rupture strength and some of its applications. 1 tab

  18. A major advance in powder metallurgy

    Science.gov (United States)

    Williams, Brian E.; Stiglich, Jacob J., Jr.; Kaplan, Richard B.; Tuffias, Robert H.

    1991-01-01

    Ultramet has developed a process which promises to significantly increase the mechanical properties of powder metallurgy (PM) parts. Current PM technology uses mixed powders of various constituents prior to compaction. The homogeneity and flaw distribution in PM parts depends on the uniformity of mixing and the maintenance of uniformity during compaction. Conventional PM fabrication processes typically result in non-uniform distribution of the matrix, flaw generation due to particle-particle contact when one of the constituents is a brittle material, and grain growth caused by high temperature, long duration compaction processes. Additionally, a significant amount of matrix material is usually necessary to fill voids and create 100 percent dense parts. In Ultramet's process, each individual particle is coated with the matrix material, and compaction is performed by solid state processing. In this program, Ultramet coated 12-micron tungsten particles with approximately 5 wt percent nickel/iron. After compaction, flexure strengths were measured 50 percent higher than those achieved in conventional liquid phase sintered parts (10 wt percent Ni/Fe). Further results and other material combinations are discussed.

  19. Copper alloys with improved properties: standard ingot metallurgy vs. powder metallurgy

    Directory of Open Access Journals (Sweden)

    Milan T. Jovanović

    2014-09-01

    Full Text Available Three copper-based alloys: two composites reinforced with Al2O3 particles and processed through powder metallurgy (P/M route, i.e. by internal oxidation (Cu-2.5Al composite and by mechanical alloying (Cu-4.7Al2O3 and Cu-0.4Cr-0.08Zr alloy produced by ingot metallurgy (vacuum melting and casting were the object of this investigation. Light microscope and scanning electron microscope (SEM equipped with electron X-ray spectrometer (EDS were used for microstructural characterization. Microhardness and electrical conductivity were also measured. Compared to composite materials, Cu-0.4Cr-0.08Zr alloy possesses highest electrical conductivity in the range from 20 to 800 ℃, whereas the lowest conductivity shows composite Cu-2.5Al processed by internal oxidation. In spite to somewhat lower electrical conductivity (probably due to inadequate density, Cu-2.5Al composite exhibits thermal stability enabling its application at much higher temperatures than materials processed by mechanical alloying or by vacuum melting and casting.

  20. Analyses of Ferrous and Ferric State in DynabiTab Using Mössbauer Spectroscopy

    Directory of Open Access Journals (Sweden)

    Young Rang Uhm

    2017-01-01

    Full Text Available Antianemic medicament ferrous gluconate, ferrous fumarate, and a Dynabi tablet with a basic iron bearing ingredient were studied with the use of Mössbauer spectroscopy. Room temperature spectra of ferrous gluconate gave clear evidence that the two phases of iron were present: ferrous (Fe2+ as a major one with a contribution at and above 91 a.u.% and ferric (Fe3+ whose contribution was found to be ~9 a.u.%. In the case of ferrous fumarate, a single phase was measured corresponding to ferrous (Fe2+ state. A Dynabi tablet consists of ferrous fumarate and ferrous fumarate. The ferric phase in ferrous gluconate is able to be reached about ~3.6 a.u.% in a tablet.

  1. Technetium behavior in sulfide and ferrous iron solutions

    International Nuclear Information System (INIS)

    Lee, S.Y.; Bondietti, E.A.

    1982-01-01

    Pertechnetate oxyanion ( 99 TcO 4- ), a potentially mobile species in leachate from a breached radioactive waste repository, was removed from a brine solution by precipitation with sulfide, iron, and ferrous sulfide at environmental pH's. Maghemite (ν-Fe 2 O 3 ) and geothite (α-FeOOH) were the dominant minerals in the precipitate obtained from the TcO 4- -ferrous iron reaction. The observation of small particle size and poor crystallinity of the minerals formed in the presence of Tc suggested that the Tc was incorporated into the mineral structure after reduction to a lower valence state. Amorphous ferrous sulfide, an initial phase precipitating in the TcO 4- -ferrous iron-sulfide reaction, was transformed to goethite and hematite (α-Fe 2 O 3 ) on aging. The black precipitate obtained from the TcO 4- -sulfide reaction was poorly crystallized technetium sulfide (Tc 2 S 7 ) which was insoluble in both acid and alkaline solution in the absence of strong oxidents. The results suggested that ferrous- and/or sulfide-bearing groundwaters and minerals in host rocks or backfill barriers could reduce the mobility of Tc through the formation of less-soluble Tc-bearing iron and/or sulfide minerals

  2. 78 FR 8202 - Meeting of the Joint ACRS Subcommittees on Thermal Hydraulic Phenomena and Materials, Metallurgy...

    Science.gov (United States)

    2013-02-05

    ... Hydraulic Phenomena and Materials, Metallurgy and Reactor Fuels; Notice of Meeting The Joint ACRS Subcommittees on Thermal Hydraulic Phenomena and Materials, Metallurgy and Reactor Fuels will hold a meeting on...

  3. The Metallurgy of some indian swords

    Directory of Open Access Journals (Sweden)

    Williams, Alan

    2007-12-01

    Full Text Available The metallurgy of Indian swords shows many differences from that of European swords. The distinction between "Damascus Steel" (or wootz and crucible steel is explained. Ten broken blades from the Armoury of the Nizams of Hyderabad were made available for microscopic examination. Six of these seem to been made from crucible steels, and are of notably high quality. By contrast, a group of six randomly collected from Private Collections in England were also examined. Only one of these was made of crucible steel, and three of the others were of very mediocre quality. This perhaps represents the quality of blades available to the average Indian soldier.

    La metalurgia de las espadas indias presenta notables diferencias en comparación con la de las europeas. Se explica la distinción entre el ‘acero de Damasco’ (o wootz y el acero de crisol. Se ha realizado un análisis microscópico de un conjunto de diez hojas rotas de espada depositadas en la Armería de los Nizams de Hyderabad. Seis de ellas parecen haber sido realizadas a partir de acero de crisol, y son de elevada calidad. En contraste, se examinó también un grupo de seis espadas de colecciones privadas en Inglaterra. Sólo una de ellas estaba fabricada con acero de crisol, y tres de las otras eran de calidad muy mediocre. Esto representa quizá la calidad de las hojas de espada al alcance del soldado medio indio.

  4. Biennial activity report of Metallurgy Programme - 1985 and 1986

    International Nuclear Information System (INIS)

    Mallika, C.; Sreenivasan, P.R.; Muraleedharan, P.; Shyamsunder, M.T.; Kuppuswami, P.; Sampath, N.; Bhaduri, A.K.; Sreedharan, O.M.

    1988-01-01

    The biennial activity report of the Metallurgy Programme of the Indira Gandhi Centre for Atomic Research covers the period of the years 1985 and 1986. Along with NDT, welding metallurgy, low cycle fatigue, creep and creep fatigue interactions, structure-property correlations, thermodynamics and corrosion metallurgy of alloy steels with respect to their compatibility with aqueous and liquid sodium environments continue to be the major thrust areas of the Programme. Some of the basic research contributions of the Programme are: the observation of uniform and homogeneous distribution of voids in cyclically deformed 304 SS, the role of grain boundaries and precipitation in dynamic strain ageing of 316 SS and the determination of the activities of component metals in 316 and 304 SS by metastable EMF method. (author)

  5. Introduction to powder metallurgy processes for titanium manufacturing

    International Nuclear Information System (INIS)

    Esteban, P. G.; Bolzoni, L.; Ruiz-Navas, E. M.; Gordo, E.

    2011-01-01

    The development of new extraction processes to produce titanium in powder form leads Powder Metallurgy to an advantage position among the manufacturing processes for titanium. The cost reduction of base material, coupled with the economy of the powder metallurgy processes, give titanium industry the chance to diversify its products, which could lead to production volumes able to stabilise the price of the metal. This work reviews some of the Powder Metallurgy techniques for the manufacturing of titanium parts, and describes the two typical approaches for titanium manufacturing: Blending Elemental and Prealloyed Powders. Among others, conventional pressing and sintering are described, which are compared with cold and hot isostatic pressing techniques. Real and potential applications are described. (Author) 71 refs.

  6. ABOUT HEAT TREATMENTS APPLIED TO FERROUS ALLOYS AND METALS

    Directory of Open Access Journals (Sweden)

    Alin Stancioiu

    2016-05-01

    Full Text Available Materials and non-ferrous alloys lends itself through more plastic deformation processes. It is known that after deformation the material structure, as well as properties that are no longer adequate therefore is applied recrystallization annealing for the purpose of restore the initial structure. To increase the hardness of non-ferrous alloys it must after hardening the cooling rate to be slow. This is explained by the fact that of chemical compounds give time to precipitate on the edge of grain to the base of the constituents of alloys.

  7. Summarizing of new techniques in uranium mining and metallurgy

    International Nuclear Information System (INIS)

    Wang Delin; Zhang Fei; Su Yanru; Zeng Yijun; Meng Jin

    2010-01-01

    According to character of national resources and uranium mining and metallurgical science and technology members research achievements, new techniques in ten scientific research area of in-situ leaching, heap leaching, multi-metal comprehensive recovery, bio-metallurgy etc. for 10 years is introduced in this paper. The level of innovation ability is shown by technical index, resources recovery and reduction capital cost etc. datum. The application bound of natural uranium resource is enlarged and production ability of national uranium is increased. It is put forward renovation and development ideas for uranium mining and metallurgy. (authors)

  8. Metallurgy and properties of plasma spray formed materials

    Science.gov (United States)

    Mckechnie, T. N.; Liaw, Y. K.; Zimmerman, F. R.; Poorman, R. M.

    1992-01-01

    Understanding the fundamental metallurgy of vacuum plasma spray formed materials is the key to enhancing and developing full material properties. Investigations have shown that the microstructure of plasma sprayed materials must evolve from a powder splat morphology to a recrystallized grain structure to assure high strength and ductility. A fully, or near fully, dense material that exhibits a powder splat morphology will perform as a brittle material compared to a recrystallized grain structure for the same amount of porosity. Metallurgy and material properties of nickel, iron, and copper base alloys will be presented and correlated to microstructure.

  9. Emission profiles of polychlorinated dibenzodioxins, polychlorinated dibenzofurans (PCDD/Fs), dioxin-like PCBs and hexachlorobenzene (HCB) from secondary metallurgy industries in Portugal.

    Science.gov (United States)

    Antunes, Pedro; Viana, Paula; Vinhas, Tereza; Rivera, J; Gaspar, Elvira M S M

    2012-09-01

    This paper reports, for the first time, a study of dioxin emissions from 10 siderurgies and metallurgies, secondary copper, aluminum and lead metallurgies, in Portugal. The study reports the emission factors and total emission amounts of PCDD/Fs, dioxin-like PCBs and hexachlorobenzene (HCB). The congener patterns were characterized and are discussed. The results showed that the total amount of PCDFs is higher than PCDDs in flue gas of each industrial unit. The toxic equivalent emission factors of pollutants emitted are 3098-3338 ngI-TEQt(-1) for PCDD/Fs and 597-659 ng I-TEQt(-1) for dioxin-like PCBs in siderurgies production (total estimated emission amounts released to atmosphere of 3.9-4.5 g I-TEQyr(-1)), 50-152 ng I-TEQt(-1) for PCDD/Fs and 24-121 ng I-TEQt(-1) for dioxin-like PCBs in ferrous foundries production (total estimated emission amounts released to atmosphere of 0.0010-0.0016 g I-TEQyr(-1)) and 5.8-5715 ng I-TEQt(-1) for PCDD/Fs and 0.49-259 ng I-TEQt(-1) for dioxin-like PCBs in non-ferrous foundries production (total estimated emission amounts released to atmosphere of 0.00014-0.12 g I-TEQyr(-1)). The HCB emission from siderurgies production is 0.94-3.2 mg t(-1) (total estimated emission amounts released 0.94-3.8 g yr(-1)), being much smaller, residual, in the emissions of the other types of plants (0.0012-0.026 mg t(-1) production and total estimated emission amounts released to atmosphere of 0.013-1.7 mg yr(-1)). Copyright © 2012 Elsevier Ltd. All rights reserved.

  10. Ion implanting ferrous metals to improve corrosion resistance

    International Nuclear Information System (INIS)

    Dearnaley, G.; Goode, P.D.

    1981-01-01

    A process is described for the treatment of a surface of a ferrous article to improve its corrosion resistance, wherein the surface is subjected to ion bombardment at a temperature above one hundred degrees centigrade in an evacuated enclosure which contains a residual quantity of gaseous oxygen. (author)

  11. Evaluation of iron transport from ferrous glycinate liposomes using ...

    African Journals Online (AJOL)

    Background: Iron fortification of foods is currently a strategy employed to fight iron deficiency in countries. Liposomes were assumed to be a potential carrier of iron supplements. Objective: The objective of this study was to investigate the iron transport from ferrous glycinate liposomes, and to estimate the effects of liposomal ...

  12. Lithium compatibility research: status and requirements for ferrous materials

    International Nuclear Information System (INIS)

    Selle, J.E.; Olson, D.L.

    1978-01-01

    A brief historical review and a description of the present status of the knowledge accumulated on lithium-ferrous alloy corrosion research are presented and discussed. The effects of various parameters are discussed and the future requirements of lithium corrosion research are presented and discussed

  13. Radiation dose distribution measured in hydrogels containing ferrous ions

    International Nuclear Information System (INIS)

    Jin Tao; Murat, A.Q.; Liu Shilian; Duan Shengrong

    1990-01-01

    By the aid of nuclear magnetic resonance and dual wavelength TLC scanner, the absorbed dose distribution in hydrogels containing ferrous sulfate has been measured. The result shows a good straight line between the proton longitudinal relaxation rate and absorbed dose up to 16 Gy in agarose gels. It appeared that thin layer of acrylamide is much better than film for obtaining smooth dose curves

  14. The utilization of mechanochemistry in the extractive metallurgy and at the nanocrystalline materials preparation

    Directory of Open Access Journals (Sweden)

    Boldižárová Eva

    2002-03-01

    Full Text Available The possibility of the application of mechanochemistry in the extractive metallurgy and the nanocrystalline materials preparation is studied. The aim of the experiments is the chloride leaching of a complex sulphidic CuPbZn concentrate (Hodruša-Hámre, the modification of properties of CaCO3 (Yauli, Peru for zinc sorption from model solutions and the mechanochemical reduction of copper sulphide by elemental iron.The chloride leaching of mechanically activated complex sulphidic CuPbZn concentrate is a selective process. While the recoveries of copper, lead and zinc are 65-85 %, the recoveries of silver and gold are less than 7 % and 2 %, respectively.The positive influence of CaCO3 mechanical activation for zinc sorption from ZnSO4 solution was observed. While only 58 % of zinc sorption was determined after 30 minutes for a non-activated sample, 98 % of zinc sorption was determined after 3 minutes sorption for the sample mechanically activated for 15 minutes.By the mechanochemical reduction of copper sulphide with iron, nanocrystalline copper and iron sulphide are formed. This reaction is an example of the new “solid state technology“, where chemical processes in the gaseous and liquid states are excluded.The results can serve as a contribution to the optimization of copper, lead and zinc extraction from complex sulphidic concentrates, the increase of non-ferrous metals sorption efficiency on mineral sorbents as well as to the nanocrystalline copper preparation.The application of mechanical activation has grown in the laboratory research. The Institute of Geotechnics of SAS has also achieved significant theoretical results in study of mechanical activation of sulphides and their reactivity in the different solid-phase reactions with the effect on industrial applications. The Institute has developed the technology of mechanochemical leaching (process MELT which was successfully tested in a pilot plant unit.

  15. The effect of powder metallurgy process parameters on mechanical ...

    African Journals Online (AJOL)

    The ever-increasing development of applying the iron pieces made by powder metallurgy in car industries and other usages depends on making pieces with high density and consequently acceptable physical and mechanical properties. Regarding the effect of decrease in the powder bits' size on improvement of the ...

  16. Chemical and Metallurgy Research (CMR) Sample Tracking System Design Document

    International Nuclear Information System (INIS)

    Bargelski, C. J.; Berrett, D. E.

    1998-01-01

    The purpose of this document is to describe the system architecture of the Chemical and Metallurgy Research (CMR) Sample Tracking System at Los Alamos National Laboratory. During the course of the document observations are made concerning the objectives, constraints and limitations, technical approaches, and the technical deliverables

  17. Damage on 316LN stainless steel transformed by powder metallurgy

    International Nuclear Information System (INIS)

    Couturier, R.; Burlet, H.

    1998-01-01

    This study deals with the 316 LN stainless steel elaboration by powder metallurgy. This method allows the realization of structures in austenitic steel less affected by the thermal aging than the cast austenitic-ferritic components. The components are performed by the method of HIP (Hot Isostatic Pressing). Mechanical tests are provided to control mechanical properties

  18. Iron Metallurgy: Technical Terminology Bulletin. Terminotech, Vol. 2, No. 7.

    Science.gov (United States)

    General Electric Co. of Canada, Ltd., Montreal, Quebec.

    This issue of a bulletin of technological terminology is devoted to iron metallurgy. Various aspects of iron production are described in both French and English. An English-French dictionary of terms comprises the bulk of the document. Explanatory illustrations are appended. (JB)

  19. [Hygienic evaluation of risk factors on powder metallurgy production].

    Science.gov (United States)

    2011-01-01

    Complex hygienic, clinical, sociologic and epidemiologic studies revealed reliable relationship between work conditions and arterial hypertension, locomotory system disorders, monocytosis in powder metallurgy production workers. Findings are more probable cardiovascular and respiratory diseases, digestive tract diseases due to influence of lifestyle factors.

  20. 46 CFR 148.04-13 - Ferrous metal borings, shavings, turnings, or cuttings (excluding stainless steel).

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 5 2010-10-01 2010-10-01 false Ferrous metal borings, shavings, turnings, or cuttings... Requirements for Certain Material § 148.04-13 Ferrous metal borings, shavings, turnings, or cuttings (excluding... described as ferrous metal borings, shavings, turnings, or cuttings on board vessels (excluding stainless...

  1. Production of ferrous sulfate from residue from the iron mining

    International Nuclear Information System (INIS)

    Cardoso, K.A; Riella, H.G.; Abreu, E.F.; Carvalho, E.F. Urano de; Durazzo, M.

    2012-01-01

    This paper was developed from a residue obtained by processing iron ore exploited by the mining company Samarco S/A. The residue was characterized and the analyses showed that it contains about 70% of the mineral hematite (Fe 2 O 3 ) and also that some economically important products could be produced. One is the ferrous sulfate that can be used in pharmaceuticals and also that can be used in the treatment of iron deficiency anemia. The iron, in addition to is importance for the industrial production of steel and parts in general, also has great biological importance in all living beings. In order to produce ferrous sulfate from the byproduct in question, it was developed a obtaining route using metallic iron as hematite reductor and sulfuric acid to form the salt. (author)

  2. Ferrous alloys cast under high pressure gas atmosphere

    Directory of Open Access Journals (Sweden)

    Pirowski Z.

    2007-01-01

    Full Text Available The main objective of this paper is describing the essence of the process of introducing nitrogen to the melt of ferrous alloys by application of overpressure above the metal bath. The problem was discussed in terms of both theory (the thermodynamic aspects of the process and practice (the technical and technological aspects, safety of the furnace stand operation, and technique of conducting the melt. The novel technique of melting under high pressure of the gas atmosphere (up to 5 MPa has not been used so far in the domestic industry, mainly because of the lack of proper equipment satisfyng the requirements of safe operation. Owing to cooperation undertaken with a partner from Bulgaria, a more detailed investigation of this technology has become possible and melting of selected ferrous alloys was conducted under the gas atmosphere at a pressure of about 3,5 MPa.

  3. Removal of chlorite by reaction with ferrous iron

    OpenAIRE

    Iatrou, Angela

    1991-01-01

    The use of chlorine dioxide as an oxidant and/or disinfectant for drinking water treatment has been an alternative considered when utilities seek to control trihalomethane concentrations. However, concern regarding residual concentrations of chlorite and chlorate have resulted in limitations on applied chlorine dioxide dosages. This study describes the use of ferrous iron as a possible reducing agent for the elimination of residual chlorite from drinking water.

  4. AGU Committees

    Science.gov (United States)

    Administrative Committees are responsible for those functions required for the overall performance or well-being of AGU as an organization. These committees are Audit and Legal Affairs, Budget and Finance*, Development, Nominations*, Planning, Statutes and Bylaws*, Tellers.Operating Committees are responsible for the policy direction and operational oversight of AGU's primary programs. The Operating Committees are Education and Human Resources, Fellows*, Information Technology, International Participation*, Meetings, Public Affairs, Public Information, Publications*.

  5. Analysis of effectiveness of the state industrial policy in ferrous metallurgy of Ukraine for the period 1996 – 2010 Анализ результативности государственной промышленной политики в черной металлургии Украины за 1996 – 2010 гг.

    Directory of Open Access Journals (Sweden)

    Denisov Konstantin V.

    2013-03-01

    Full Text Available The article contains analysis of results of realisation of legislative and regulatory acts, which determined development of the state industrial policy in ferrous metallurgy of Ukraine from 1996 till 2010. Analysis was conducted with the use of national statistics and international organisations: World Steel Association and International Steel Statistical Bureau. Analysis showed discrepancy of obtained results with the goals, which were set by the state within the framework of the branch industrial policy. This concerns development of the industrial and technological base, trade structure of production and export and also internal consumption of steel. Despite a number of benefits provided by the state, the technological level of the branch was low. Primary steel and semi-finished products dominate in the trade structure of production. Internal consumption of steel is limited and is lower than export indicators. The situation in other countries is quite opposite, due to which the article underlines a necessity to use their experience of branch industrial policy.В статье проведен анализ результатов реализации нормативно-правовых актов, которые определяли развитие государственной промышленной политики в черной металлургии Украины с 1996 по 2010 гг. Анализ проводился с использованием данных национальной статистики, а также международных организаций World Steel Association и Іnternational Steel Statistical Bureau. Анализ показал несоответствие полученных результатов тем целям, которые определялись государством в рамках отраслевой промышленной политики. Это касается

  6. Powder Metallurgy characteristics and application: state of the art

    International Nuclear Information System (INIS)

    Zaid, A.I.O.

    2005-01-01

    Powder metallurgy process (P/M) is a near-net or net-shape manufacturing process that combines the features of shape making technology of powder compaction with the development of final material and design properties (physical and mechanical) during subsequent densification or consolidation processes, e.g. sintering. It utilizes the metal powder or powders of metal alloys. In this paper, the major historical developments in P/M are reviewed and discussed. The main parameters involved in the process and their effects on the product characteristics are presented and discussed, which include: powders and methods of their production, particle size and shape, compressibility and additives, sintering temperature and time and finishing processes. The advantages and limitations of powder metallurgy are also presented and discussed. Finally, applications and future developments of the process are outlined and discussed. (author)

  7. Powder Metallurgy Fabrication of Molybdenum Accelerator Target Disks

    Energy Technology Data Exchange (ETDEWEB)

    Lowden, Richard Andrew [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Kiggans Jr., James O. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Nunn, Stephen D. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Parten, Randy J. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

    2015-07-01

    Powder metallurgy approaches for the fabrication of accelerator target disks are being examined to support the development of Mo-99 production by NorthStar Medical Technologies, LLC. An advantage of powder metallurgy is that very little material is wasted and, at present, dense, quality parts are routinely produced from molybdenum powder. The proposed targets, however, are thin wafers, 29 mm in diameter with a thickness of 0.5 mm, with very stringent dimensional tolerances. Although tooling can be machined to very high tolerance levels, the operations of powder feed, pressing and sintering involve complicated mechanisms, each of which affects green density and shrinkage, and therefore the dimensions and shape of the final product. Combinations of powder morphology, lubricants and pressing technique have been explored to produce target disks with minimal variations in thickness and little or no distortion. In addition, sintering conditions that produce densities for optimum target dissolvability are being determined.

  8. Uranium 2000 : International symposium on the process metallurgy of uranium

    International Nuclear Information System (INIS)

    Ozberk, E.; Oliver, A.J.

    2000-01-01

    The International Symposium on the Process Metallurgy of Uranium has been organized as the thirtieth annual meeting of the Hydrometallurgy Section of the Metallurgical Society of the Canadian Institute of Mining, Metallurgy and Petroleum (CIM). This meeting is jointly organized with the Canadian Mineral Processors Division of CIM. The proceedings are a collection of papers from fifteen countries covering the latest research, development, industrial practices and regulatory issues in uranium processing, providing a concise description of the state of this industry. Topics include: uranium industry overview; current milling operations; in-situ uranium mines and processing plants; uranium recovery and further processing; uranium leaching; uranium operations effluent water treatment; tailings disposal, water treatment and decommissioning; mine decommissioning; and international regulations and decommissioning. (author)

  9. Microstructure and Aging of Powder-Metallurgy Al Alloys

    Science.gov (United States)

    Blackburn, L. B.

    1987-01-01

    Report describes experimental study of thermal responses and aging behaviors of three new aluminum alloys. Alloys produced from rapidly solidified powders and contain 3.20 to 5.15 percent copper, 0.24 to 1.73 percent magnesium, 0.08 to 0.92 percent iron, and smaller amounts of manganese, nickel, titanium, silicon, and zinc. Peak hardness achieved at lower aging temperatures than with standard ingot-metallurgy alloys. Alloys of interest for automobile, aircraft, and aerospace applications.

  10. Powder-metallurgy superalloy strengthened by a secondary gamma phase.

    Science.gov (United States)

    Kotval, P. S.

    1971-01-01

    Description of experiments in which prealloyed powders of superalloy compositions were consolidated by extrusion after the strengthening by precipitation of a body-centered tetragonal gamma secondary Ni3 Ta phase. Thin foil electron microscopy showed that the mechanical properties of the resultant powder-metallurgy product were correlated with its microstructure. The product exhibited high strength at 1200 F without loss of ductility, after thermomechanical treatment and aging.

  11. Ferrous bisglycinate 25 mg iron is as effective as ferrous sulfate 50 mg iron in the prophylaxis of iron deficiency and anemia during pregnancy in a randomized trial

    DEFF Research Database (Denmark)

    Milman, Nils; Jønsson, Lisbeth; Dyre, Pernille

    2014-01-01

    OBJECTIVE: To compare the effects of oral ferrous bisglycinate 25 mg iron/day vs. ferrous sulfate 50 mg iron/day in the prevention of iron deficiency (ID) and iron deficiency anemia (IDA) in pregnant women. Design: Randomized, double-blind, intention-to-treat study. Setting: Antenatal care clinic...

  12. Bioleaching of heavy metals from sewage sludge by indigenous iron-oxidizing microorganisms using ammonium ferrous sulfate and ferrous sulfate as energy sources: a comparative study.

    Science.gov (United States)

    Pathak, Ashish; Dastidar, M G; Sreekrishnan, T R

    2009-11-15

    The potential of indigenous iron-oxidizing microorganisms enriched at initial neutral pH of the sewage sludge for bioleaching of heavy metals was investigated at initial neutral pH of the sludge using ammonium ferrous sulfate (FAS) and ferrous sulfate (FS) as an energy sources in two different sets of experiments. After 16 days of bioleaching, 56% Cu, 48% Ni, 68% Zn and 42% C were removed from the sludge using ammonium ferrous sulfate as an energy source. On the other hand, 64% Cu, 58% Ni, 76% Zn and 52% Cr were removed using ferrous sulfate. Further, 32% nitrogen and 24% phosphorus were leached from the sludge using ferrous sulfate, whereas only 22% nitrogen and 17% phosphorus were removed using ammonium ferrous sulfate. The BCR sequential extraction study on speciation of metals showed that using ammonium ferrous sulfate and ferrous sulfate, all the metals remained in bioleached sludge as stable form (F4 fraction). The results of the present study indicate that the bioleached sludge would be safer for land application. Also, the fertilizing property was largely conserved in the bioleached sludge using both the substrates.

  13. Mechanical and microstructural characterization of powder metallurgy CoCrNi medium entropy alloy

    Czech Academy of Sciences Publication Activity Database

    Moravčík, I.; Čížek, Jan; Kováčová, Z.; Nejezchlebová, J.; Kitzmantel, M.; Neubauer, E.; Kuběna, Ivo; Horník, Vít; Dlouhý, I.

    2017-01-01

    Roč. 701, July (2017), s. 370-380 ISSN 0921-5093 Institutional support: RVO:61389021 ; RVO:68081723 Keywords : tensile test * mechanical alloying * plasticity * mechanical characterization * powder metallurgy Subject RIV: JG - Metallurgy; JG - Metallurgy (UFM-A) OBOR OECD: Materials engineering ; Materials engineering (UFM-A) Impact factor: 3.094, year: 2016 https://www.sciencedirect.com/science/article/pii/S0921509317308535

  14. Development of Cu-Be bronzes through powder metallurgy

    International Nuclear Information System (INIS)

    Abbas, M.

    2012-01-01

    Copper and copper alloys are the major group of commercial alloy. One of the important copper bronzes is Copper beryllium. This is unique among all engineering alloys. Copper beryllium alloy possesses the highest strength in all the copper base alloys. Development of copper beryllium alloy with powder metallurgy is challenging problem due to toxicity of beryllium dust. Purpose of this project to find out parameters by which copper beryllium with all unique properties should obtained. For this purpose efforts are put on development of alternative to copper beryllium system like copper-tin and copper-aluminum by powder metallurgy route. Different time of milling with uniaxial pressure of about 200 MPa and different sintering temperature according to phase diagram of alloy, with different soaking time is tried. Problems may occur like decrease in density after sintering, breaking of samples by Rockwell A, B and C indenters arid by hammering. Cold iso-static pressing at 300 MPa and sintering at above 900 degree C is used to develop copper beryllium alloy. As quenched samples are heat treated at 260 degree C, 315 degree C and 370 degree C with different soaking time of 30, 90 and 180 minutes to find out optimum time and temperature parameters. . It is observed that at aging at 260 degree C for 180 minutes, aging at 315 degree C for 180 minutes and aging at 370 degree C for 30 minutes produce optimum result. By observing these pellets by SEM, precipitates appeared in peak-aged alloy and bigger precipitates in over-aged alloy. Copper beryllium alloy developed through powder metallurgy has better prospects than other copper bronzes. (author)

  15. Welding Metallurgy and Processing Issues for Joining of Power Sources

    Energy Technology Data Exchange (ETDEWEB)

    Lienert, Thomas J. [Los Alamos National Laboratory; Reardon, Patrick T. [Los Alamos National Laboratory

    2012-08-14

    Weldability issues with the pertinent alloys have been reviewed and preliminary results of our work on Haynes 25 have been presented. Further results on the mechanical properties and metallography on the EB welds are imminent. Hot-ductility experiments will commence within a few weeks. Aging studies on the effects of heat treatment using the Gleeble are also planned. MST-6 has extensive background in the welding metallurgy of the pertinent alloys. We also have considerable experience with the various welding processes to be used.

  16. Annual report of the Metallurgy Division - period ending December 1975

    International Nuclear Information System (INIS)

    1976-01-01

    The R and D activities of the Metallurgy Division of the Bhabha Atomic Research Centre, Bombay (India) during 1975 are described. Some of the R and D programmes of particular interest to nuclear technology are: (1) flowsheet development for the production of rare metals and alloys of nuclear use e.g. hafnium, beryllium, zirconium (2) metallurgical, irradiation hardening and corrosion studies on Zr and Zr-base alloys and (3) studies of nuclear ceramic materials such as UO2 and beryllia. (M.G.B.)

  17. Powder Metallurgy Reconditioning of Food and Processing Equipment Components

    Science.gov (United States)

    Nafikov, M. Z.; Aipov, R. S.; Konnov, A. Yu.

    2017-12-01

    A powder metallurgy method is developed to recondition the worn surfaces of food and processing equipment components. A combined additive is composed to minimize the powder losses in sintering. A technique is constructed to determine the powder consumption as a function of the required metallic coating thickness. A rapid method is developed to determine the porosity of the coating. The proposed technology is used to fabricate a wear-resistant defectless metallic coating with favorable residual stresses, and the adhesive strength of this coating is equal to the strength of the base metal.

  18. Properties of porous magnesium prepared by powder metallurgy.

    Science.gov (United States)

    Čapek, Jaroslav; Vojtěch, Dalibor

    2013-01-01

    Porous magnesium-based materials are biodegradable and promising for use in orthopaedic applications, but their applications are hampered by their difficult fabrication. This work reports the preparation of porous magnesium materials by a powder metallurgy technique using ammonium bicarbonate as spacer particles. The porosity of the materials depended on the amount of ammonium bicarbonate and was found to have strong negative effects on flexural strength and corrosion behaviour. However, the flexural strength of materials with porosities of up to 28 vol.% was higher than the flexural strength of non-metallic biomaterials and comparable with that of natural bone. Copyright © 2012 Elsevier B.V. All rights reserved.

  19. Preliminary analysis about reducing production costs in uranium mining and metallurgy at Fuzhou uranium mine

    International Nuclear Information System (INIS)

    Wu Sanmao

    1999-01-01

    The production costs in uranium ming and metallurgy have been analyzed quantitatively term by term according to present production situation for The Uranium Mining and Metallurgy Corp, which is part of Fuzhou Uranium Mine. The principal factors influencing on the production costs and the main means reducing the production costs have been found

  20. Magnetic Resonance Imaging Dosimetry application to chemical ferrous gels

    International Nuclear Information System (INIS)

    Calmet, Ch.

    2000-10-01

    MRI dosimetry is based on the determination of relaxation parameters (T1, T2). Chemical detectors whose NMR properties are sensitive to irradiation are used. Difficulties in absolute relaxation times measure limit the use of this technique. The aim of this work first consists in the development of a quantitative method to determine T, relaxation time on irradiated ferrous gels. So, we can study processes and parameters which affect the technique sensibility. The method sensitivity first depends on imaging instrumentation. Quantitative MRI method used is able to eliminate variable imager factors. The study of instrumental parameters (coil, sequence parameters) permits to define an imaging protocol which is a function of the considered application (volume size, spatial resolution and accuracy). The method sensitivity depends on the detector sensibility too. The best composition of ferrous gel has been determined. Dose distributions are obtained in three minutes. Comparison between MRI results and conventional dosimetry methods (specially ionisation chamber and films) shows a deviation of about 5% for single irradiation with energy fields in the range of 300 keV to 25 MeV. So, the proposed method forms a suitable technique for 3D dosimetry. (author)

  1. Clean ferrous casting technology research. Final technical report, September 29, 1993--December 31, 1995

    Energy Technology Data Exchange (ETDEWEB)

    Piwonka, T.S. [ed.

    1996-01-01

    This report details results of a 30-month program to develop methods of making clean ferrous castings, i.e., castings free of inclusions and surface defects. The program was divided into 3 tasks: techniques for producing clean steel castings, electromagnetic removal of inclusions from ferrous melts, and study of causes of metal penetration in sand molds in cast iron.

  2. The mysterious world of plutonium metallurgy: Past and future

    International Nuclear Information System (INIS)

    Hecker, S.S.; Hammel, E.F.

    1998-01-01

    The first atomic bomb detonated at the Trinity Site in New Mexico on July 16, 1945, used plutonium, a man-made element discovered < 5 yr earlier. The story of how Manhattan Project scientists and engineers tackled the mysteries of this element and fabricated it into the first atomic bomb is one of the most fascinating in the history of metallurgy and materials. The authors are currently trying to generate renewed interest in plutonium metallurgy because of the challenge posed by President Clinton, i.e., to keep the nuclear stockpile of weapons safe and reliable without nuclear testing. The stockpile stewardship challenge requires either a lifetime extension of the plutonium components or a remanufacture--neither of which can be verified by testing. In turn, this requires that one achieve a better fundamental understanding of plutonium. Of special interest is the effect of self-irradiation on the properties and on the long-term stability of plutonium and its alloys. Additional challenges arise from long-term concerns about disposing of plutonium and dealing with its environmental legacy. It is imperative to interest the next generation of students in these plutonium challenges

  3. Stress analyses of pump gears produced by powder metallurgy

    Energy Technology Data Exchange (ETDEWEB)

    Cetinel, Hakan [Celal Bayar Univ., Mechanical Engineering Dept. (Turkey); Yilmaz, Burak

    2013-06-01

    In this study, trochoidal type (gerotor) hydraulic pump gears were produced by powder metallurgy (P/M) technique. Several gears with different mechanical properties have been obtained by changing process variables. The tooth contact stresses were calculated analytically under particular operation conditions of the hydraulic pump. The 3D models have been obtained from real gears by using Capability Maturity Model (CMM, 3D scanning) operation and SOLIDWORKS software. Stress analyses were conducted on these 3D models by using ANSYS WORKBENCH software. It was found that the density increases by the increase of sintering duration and mechanical properties were positively affected by the increase of density. Maximum deformation takes place in the region of the outer gear where failure generally occurs with the minimum cross-section area.

  4. An application of powder metallurgy for the LHC

    CERN Document Server

    Sgobba, Stefano

    2004-01-01

    The cold mass of the 1232 superconducting dipole magnets of LHC, operating at 1.9 K, is enclosed by a shrinking cylinder and two end covers at its extremities. The covers are structural components that must retain high strength and toughness at cryogenic temperature. They are manufactured by Metso Oy /FI in AISI 316 LN steel by Powder Metallurgy (PM) and Hot Isostatic Pressing. PM represents an attractive near net shaping technique for these components of complex geometry for which dimension tolerances, dimensional stability, weldability are key issues for magnet fabrication, and mechanical properties, ductility and leak tightness have to be guaranteed during operation. The material of the covers and its welds have been fully characterized and mechanically tested down to 4.2 K at CERN. The fine grained structure, the absence of residual stresses, the full isotropy of mechanical properties associated to the low level of Prior Particle Boundaries oxides result in superior mechanical properties and high ductilit...

  5. N18, powder metallurgy superalloy for disks: Development and applications

    Energy Technology Data Exchange (ETDEWEB)

    Guedou, J.Y.; Lautridou, J.C.; Honnorat, Y. (SNECMA, Evry (France). Materials and Processes Dept.)

    1993-08-01

    The preliminary industrial development of a powder metallurgy (PM) superalloy, designated N18, for disk applications has been completed. This alloy exhibits good overall mechanical properties after appropriate processing of the material. These properties have been measured on both isothermally forged and extruded billets, as well as on specimens cut from actual parts. The temperature capability of the alloy is about 700 C for long-term applications and approximately 750 C for short-term use because of microstructural instability. Further improvements in creep and crack propagation properties, without significant reduction in tensile strength, are possible through appropriate thermomechanical processing, which results in a large controlled grain size. Spin pit tests on subscale disks have confirmed that the N18 alloy has a higher resistance than PM Astrology and is therefore an excellent alloy for modern turbine disk applications.

  6. Powder metallurgy: Solid and liquid phase sintering of copper

    Science.gov (United States)

    Sheldon, Rex; Weiser, Martin W.

    1993-01-01

    Basic powder metallurgy (P/M) principles and techniques are presented in this laboratory experiment. A copper based system is used since it is relatively easy to work with and is commercially important. In addition to standard solid state sintering, small quantities of low melting metals such as tin, zinc, lead, and aluminum can be added to demonstrate liquid phase sintering and alloy formation. The Taguchi Method of experimental design was used to study the effect of particle size, pressing force, sintering temperature, and sintering time. These parameters can be easily changed to incorporate liquid phase sintering effects and some guidelines for such substitutions are presented. The experiment is typically carried out over a period of three weeks.

  7. Advanced powder metallurgy aluminum alloys via rapid solidification technology

    Science.gov (United States)

    Ray, R.

    1984-01-01

    Aluminum alloys containing 10 to 11.5 wt. pct. of iron and 1.5 to 3 wt. pct. of chromium using the technique of rapid solidification powder metallurgy were studied. Alloys were prepared as thin ribbons (.002 inch thick) rapidly solidified at uniform rate of 10(6) C/second by the melt spinning process. The melt spun ribbons were pulverized into powders (-60 to 400 mesh) by a rotating hammer mill. The powders were consolidated by hot extrusion at a high reduction ratio of 50:1. The powder extrusion temperature was varied to determine the range of desirable processing conditions necessary to yield useful properties. Powders and consolidated alloys were characterized by SEM and optical metallography. The consolidated alloys were evaluated for (1) thermal stability, (2) tensile properties in the range, room temperature to 450 F, and (3) notch toughness in the range, room temperature to 450 F.

  8. Annual report for the steering committee of the association Euratom-Belgian State for fusion 1996

    Energy Technology Data Exchange (ETDEWEB)

    Moons, F.; Bogaerts, W.; Decreton, M.; Biver, E.; Coenen, S.; Benoit, Ph.; Coheur, L.; Deboodt, P.; Andreev, D.

    1996-09-01

    This report is prepared for the annual steering committee meting of the Association Euratom - Belgian State for Fusion. The period October 1995 to September 1996 is reported on.The fusion technology work performed at the Belgian Nuclear Research Centre SCK/CEN, the Department of Metallurgy and Materials Engineering of the Louvain University (Belgium) and S.A. Gradel, a Luxemburg company, is described.

  9. Annual report for the steering committee of the association Euratom-Belgian State for fusion 1996

    International Nuclear Information System (INIS)

    Moons, F.; Bogaerts, W.; Decreton, M.; Biver, E.; Coenen, S.; Benoit, Ph.; Coheur, L.; Deboodt, P.; Andreev, D.

    1996-09-01

    This report is prepared for the annual steering committee meting of the Association Euratom - Belgian State for Fusion. The period October 1995 to September 1996 is reported on.The fusion technology work performed at the Belgian Nuclear Research Centre SCK/CEN, the Department of Metallurgy and Materials Engineering of the Louvain University (Belgium) and S.A. Gradel, a Luxemburg company, is described

  10. Application of the ecologically clean technology of mining metallurgy and power industry wastes recycling based on the use of electron beams

    International Nuclear Information System (INIS)

    Mazhrenova, N.R.; Askarova, G.Sh.

    1997-01-01

    Advantage of electron beam technologies application for industrial wastes recycling is illustrated for following trends: 1).Off gases of mining metallurgy and the thermal power plant can be refined from SO 2 and NO x toxic combination by means of their further chemical and radiation oxidation with following obtaining of acids on the base industrial accelerator ELV-8. In this method a radiation-chemical process in irradiated gas results in excited complexes, radicals and ion formation. Ion cause the activation of reaction chain which convert SO 2 and NO x toxic gases into the combination with high number of oxidation. In presence of water, coming from drip cooler, the combination of sulphuric and nitric acids neutralization results in the obtaining of ammonium solid combination which are mainly sulphates and nitrates; 2). For waste water refinement from organic pollution, for instance butyl xanthate, ions of heavy metals and etc.; 3). For non-ferrous, sparse and and dispersed metal extraction from the cinder and slag wastes. Different technological schemes for mineral extraction are elaborated

  11. Uranium mining and metallurgy library information service under the network environment

    International Nuclear Information System (INIS)

    Tang Lilei

    2012-01-01

    This paper analyzes the effect of the network environment on the uranium mining and metallurgy of the information service. Introduces some measures such as strengthening professional characteristic literature resources construction, changing the service mode, building up information navigation, deepening service, meet the individual needs of users, raising librarian's quality, promoting the co-construction and sharing of library information resources, and puts forward the development idea of uranium mining and metallurgy library information service under the network environment. (author)

  12. Production of uranium in Navoi Mining and Metallurgy Combinat, Uzbekistan

    International Nuclear Information System (INIS)

    Kuchersky, N.; Tolstov, E.A.; Mazurkevich, A.P.; Inozemzev, S.B.

    2001-01-01

    Full text: Under the conditions of constantly increasing level of development of the nuclear power, it is inevitable that the uranium stockpiles accumulated to 1985 will soon be depleted. This consideration underlies the development concept of uranium production in the Navoi Mining and Metallurgy Combinat, Uzbekistan. Because this product has become a source of hard currency revenues for the Republic, there will be a significant increase in the processed ore and output of uranium oxide within the next few years. Uranium production in the Navoi Mining and Metallurgy Combinat represents a full-cycle operations ranging from geological survey through hydrometallurgical processing resulting in the output of uranium concentrate in the form of uranium protoxide-oxide (U 3 O 8 ). The NMMC uranium operations include the Hydrometallurgical Plant and three facilities accomplishing ISL mining facilities. A successful start on the development of the Uchkuduk deposit by ISL method in the 1960s gave rise to scientific and production approach for development of other uranium deposits of the infiltration bedded (sandstone) type. Uranium recovery by ISL has become a separate mining branch within the 30-year period of its history and the contribution of this branch in uranium production has steadily grown. Since 1995 all uranium produced by Navoi Mining and Metallurgy Combinat is attributed to ISL. During this evolution period of the ISL method, a whole range of systematic scientific research and practical works were carried out covering improvement of process flowsheets, equipment, operational methods and techniques for particular mining conditions at those specific sites. In co-operation with design and scientific research institutions, a significant number of scientific researches, test works, design and engineering projects were achieved in order to create optimal conditions for ISL mining and further processing of pregnant solutions by sorption as well as to appropriately equip

  13. Measurement of dynamic wedge angles and beam profiles by means of MRI ferrous sulphate gel dosimetry

    Science.gov (United States)

    Bengtsson, Magnus; Furre, Torbjørn; Rødal, Jan; Skretting, Arne; Olsen, Dag R.

    1996-02-01

    The purpose of this study is to examine the possible value of measuring the dose distribution in dynamic wedge photon beams using ferrous sulphate gel phantoms analysed by MRI. The wedge angles and dose profiles were measured for a field size of and for dynamic wedge angles of , , and using a 15 MV photon beam generated from a Clinac 2100 CD (Varian). The dose profiles obtained from MRI ferrous sulphate gel were in good agreement with the dose measurements performed with a diode detector array. Also, the wedge angles determined from the MRI ferrous sulphate gel agreed well with the values obtained by using film dosimetry and with calculations by use of TMS (treatment planning system) (Helax, Uppsala, Sweden). The study demonstrated that MRI ferrous sulphate gel dosimetry is an adequate tool for measurements of some beam characteristics of dynamic radiation fields.

  14. Hyperfine interactions and structures of ferrous hydroxide and green rust II in sulfated aqueous media

    International Nuclear Information System (INIS)

    Olowe, A.A.; Genin, J.M.R.; Bauer, P.

    1988-01-01

    A sulfated ferrous hydroxide is obtained by mixing NaOH with melanterite depending on the R = [SO 4 -- ]/[OH - ] ratio and leading by oxidation to the green rust II transient compound. Hyperfine parameters are presented. (orig.)

  15. Absorption of nitric oxide into aqueous solutions of ferrous chelates accompanied by instantaneous reaction

    NARCIS (Netherlands)

    Demmink, J.F; vanGils, I.C.F.; Beenackers, A.A C M

    1997-01-01

    The absorption of nitric oxide (NO) into aqueous solutions of ferrous chelates of nitrilotriacetic acid (NTA), ethylene diaminetetraacetic acid (EDTA), hydroxyethylenediaminetriacetic acid (HEDTA), and diethylenetriaminepentaacetic acid (DTPA) was studied in a stirred cell reactor. Experimental

  16. Development and application of characteristic database for uranium mining and metallurgy in the library of Beijing Research Institute of Chemical Engineering and Metallurgy

    International Nuclear Information System (INIS)

    Gao Renxi

    2012-01-01

    Beijing Research Institute of Chemical Engineering and Metallurgy (BRICEM) is a multi disciplinary comprehensive research institute engaged in uranium mining, engineering design and related material researches. After 53 years of researches and development, BRICEM has accumulated a plenty of valuable data and resources. By analyzing the actual conditions of BRICEM's technological database, this thesis aims to propose the idea of building a characteristic database for uranium mining and metallurgy. It gives an in-depth analysis on content design, development status and problems of database development, in order to come up with solutions to these problems, as well as suggestions on the future development plans of the characteristic database. (author)

  17. Modeling of mechanical properties for ferrous shape memory alloy

    International Nuclear Information System (INIS)

    Wada, Manabu; Ide, Yusuke; Mizote, Shinichiro; Naoi, Hisashi; Tsukimori, Kazuyuki

    2002-08-01

    In order to acquire technical data that are necessary for manufacture and design of the simulation test device for analyzing the core mechanics of Fast Breeder Reactor, ferrous shape memory alloy of Fe-28%Mn-6%Si-5%Cr is melted, forged and heat-treated. The microstructures are austenite. The specimens are deformed of up to 16% work-strain by tensile and compressive test, resulting in appearance of epsilon-martensite that is induced by stress. Then, heating at 673K for 10 minutes causes austenitic transformation from epsilon-martensite and shape memory strains are measured. We also investigate shape memory character of specimens, which are given, so called 'training treatment' of 5% pre-strain and recovery heat treatment. As a result, there is little difference between tensile and compressive test without training treatment and shape memory strain is 2% after being given 5% work-strain and recovery heat treatment. On the other hand, training treatment is remarkable and shape memory strain reaches to 3.7% after 5% work-strain. We analyze shape recovery character of this alloy specimen at three-point bending by using finite element method, and indicate possibility that its deformation behavior can be estimated from mechanical properties' data obtained at tensile and compressive test. (author)

  18. Development of cast ferrous alloys for Stirling engine application

    International Nuclear Information System (INIS)

    Lemkey, F.D.

    1982-01-01

    Low cost cast ferrous base alloys that can be used for cylinder and regenerator housing components of the Stirling engine were investigated. The alloys must meet the requirements of high strength and thermal fatigue resistance to approximately 1500 F, compatibility and low permeability with hydrogen, good elevated temperature oxidation/corrosion resistance, and contain a minimum of strategic elements. The phase constituents of over twenty alloy iterations were examined by X-ray diffraction. These alloy candidates were further screened for their tensile and stress rupture strength and surface stability in air at 1450 and 1600 F, respectively. Two alloys, NASAUT 1G (Fe-10Mn-20Cr-1.5C-1.0Si) and NASAUT 4G (Fe-15Mn-12Cr-3Mo-1.5C-1.0Si-1.0Nb), were chosen for more extensive elevated temperature testing. These alloys were found to exhibit nearly equivalent elevated temperature creep strength and oxidation resistance. Silicon present in these alloys at the 1 w/o level permitted the achievement of oxide scale adherence to 1600 F without loss of strength (or ductility) as was noted for equivalent additions of aluminum

  19. Friction and wear of some ferrous-base metallic glasses

    Science.gov (United States)

    Miyoshi, K.; Buckley, D. H.

    1984-01-01

    Sliding friction experiments, X-ray photoelectron spectroscopy (XPS) analysis, and electron microscopy and diffraction studies were conducted with ferrous base metallic glasses (amorphous alloys) in contact with aluminium oxide at temperatures to 750 C in a vacuum. Sliding friction experiments were also conducted in argon and air atmospheres. The results of the investigation indicate that the coefficient of friction increases with increasing temperature to 350 C in vacuum. The increase in friction is due to an increase in adhesion resulting from surface segregation of boric oxide and/or silicon oxide to the surface of the foil. Above 500 C the coefficient of friction decreased rapidly. The decrease correlates with the segregation of boron nitride to the surface. Contaminants can come from the bulk of the material to the surface upon heating and impart boric oxide and/or silicon oxide at 350 C and boron nitride above 500 C. The segregation of contaminants is responsible for the friction behavior. The amorphous alloys have superior wear resistance to crystalline 304 stainless steel. The relative concentrations of the various constituents at the surfaces of the amorphous alloys are very different from the nominal bulk compositions.

  20. Monodisperse ferrous phosphate colloids in an anoxic groundwater plume

    Science.gov (United States)

    Gschwend, Philip M.; Reynolds, Matthew D.

    1987-01-01

    Groundwater samples collected near a secondary-sewage infiltration site on Cape Cod, Massachusetts were examined for colloidal materials (10–1000 nm). In two wells the water contained a population of monodisperse 100-nm particles, detected using laser-light scattering and autocorrelation data processing. SEM and SEM-EDAX analysis of these colloidal materials collected on ultrafilters confirmed the laser light scattering result and revealed that these microparticles consisyed of primarily iron and phosphorus in a 1.86 Fe to 1.0 P stoichiometric ratio. Chemical analyses of the water samples, together with equilibrium solubility calculations, strongly suggest that the ion-activity product should exceed the solubility product of a 100-nm diameter predominantly vivianite-type (Fe3(PO4)2 · 8H2O) colloidal phase. In light of our results, we conclude that these microparticles were formed by sewage-derived phosphate combining with ferrous iron released from the aquifer solids, and that these colloids may be moving in the groundwater flow. Such a subsurface transport process could have major implications regarding the movement of particle-reactive pollutants traditionally viewed as non-mobile in groundwater.

  1. Telomerization of Vinyl Chloride with Chloroform Initiated by Ferrous Chloride-Dimethylacetamide under Ultrasonic Conditions

    Directory of Open Access Journals (Sweden)

    Hua Qian

    2015-01-01

    Full Text Available Telomerization of vinyl chloride with chloroform was investigated using ferrous chloride-dimethylacetamide system, and 42.1% yield, more than four times the one reported before, was achieved. The addition of ultrasound further improved the reaction and yield was raised to 51.9% with trace byproducts at highly reduced reaction time and temperature. Ferrous chloride-dimethylacetamide under ultrasonic irradiation acts as a very efficient catalyst system for the 1 : 1 telomerization.

  2. Effect of ferrous metal presence on lead leaching in municipal waste incineration bottom ashes.

    Science.gov (United States)

    Oehmig, Wesley N; Roessler, Justin G; Zhang, Jianye; Townsend, Timothy G

    2015-01-01

    The recovery of ferrous and non-ferrous metals from waste to energy (WTE) ash continues to advance as the sale of removed metals improves the economics of waste combustion. Published literature suggests that Fe and Fe oxides play a role in suppressing Pb leaching in the Toxicity Characteristic Leaching Procedure (TCLP); further removal of ferrous metals from WTE ashes may facilitate higher Pb leaching under the TCLP. Eight WTE bottom ash size-fractions, from three facilities, were evaluated to assess the effect of metallic Fe addition and ferrous metal removal on TCLP leaching. Metallic Fe addition was demonstrated to reduce Pb leaching; the removal of ferrous metals by magnet resulted in a decrease in total available Pb (mg/kg) in most ash samples, yet Pb leachability increased in 5 of 6 ash samples. The research points to two chemical mechanisms to explain these results: redox interactions between Pb and Fe and the sorption of soluble Pb onto Fe oxide surfaces, as well as the effect of the leachate pH before and after metals recovery. The findings presented here indicate that generators, processors, and regulators of ash should be aware of the impact ferrous metal removal may have on Pb leaching, as a substantial increase in leaching may have significant implications regarding the management of WTE ashes. Copyright © 2014 Elsevier B.V. All rights reserved.

  3. Production of titanium alloys for medical implants by powder metallurgy

    Energy Technology Data Exchange (ETDEWEB)

    Henriques, V.A.R. [Dept. de Engenharia de Materiais, Faculdade de Engenharia Quimica de Lorena, Lorena SP (Brazil); Silva, C.R.M. da [Div. de Materiais, CTA-IAE-AMR, Sao Jose dos Campos SP (Brazil)

    2001-07-01

    Titanium alloys are expected to be much more widely used for implant materials in the medical and dental fields because of their superior biocompatibility, corrosion resistance and specific strength compared with other metallic implant materials. Vanadium free alloys like Ti-6Al-7Nb and Ti-5Al-2,5Fe have been recently developed for biomedical use. More recently vanadium and aluminum free alloys composed of non-toxic elements like Nb, Ta, Zr and so on with lower modulus have been started to be developed. The {beta} type alloys like Ti-15Mo are now the main target for medical materials. A blended elemental titanium powder metallurgy process has been developed to offer low cost products. The process employs hydride-dehydride (HDH) powders and near-net shape techniques. In this work, the influence of the processing parameters and chemical composition of the elementary powders on the final microstructure was investigated. The alloys were characterized by means of scanning electron microscopy, X-ray diffraction, Vickers microhardness measurements, chemical analysis and density. The results indicate that the samples presented high densification, homogeneous chemical composition and coherent microstructures. The process parameters were defined aiming to reduce the interstitial pick-up (O, N) and to avoid the grain growth. (orig.)

  4. The traces of roman metallurgy in Eastern Serbia

    Directory of Open Access Journals (Sweden)

    Petković Sofija

    2009-01-01

    Full Text Available The archaeological traces of the Roman mining and metallurgy in eastern Serbia are rather frequent but insufficiently studied and published. Three mining-metallurgical regions abounding in gold, silver, copper, iron and lead could be distinguished there: 1. the upper course of the Pek river, metalla Pincensia, 2. the area between Bor, Zlot, Crna Reka and Rgotina and 3. the area in the river basin of Beli Timok, two latter ones had been organized as territoria metallorum. The archeometallurgical sites confirmed by investigations are: Kraku lu Jordan at the confluence of the Brodica river and the Pek river, Rudna Glava, Tilva Roš in Bor, Gamzigrad - Romuliana, Rgotina near Zaječar and Timacum Minus in the village Ravna near Knjaževac. Roman mining-metallurgical activities in eastern Serbia flourished from the end of the 3rd century, were interrupted by the invasion of Huns in AD 441. and restored in the time of emperors Anastasius and Justin I, in the end of the 5th - beginning of the 6th centuries. The Roman mining-metallurgical centers functioned in the 6th century until the Slav invasion in the beginning of the 7th century.

  5. Wear mechanisms in powder metallurgy high speed steels matrix composites

    International Nuclear Information System (INIS)

    Gordo, E.; Martinez, M. A.; Torralba, J. M.; Jimenez, J. A.

    2001-01-01

    The development of metal matrix composites has a major interest for automotive and cutting tools industries since they possess better mechanical properties and wear resistance than corresponding base materials. One of the manufacturing methods for these materials includes processing by powder metallurgy techniques. in this case, blending of both, base material and reinforcement powders constitute the most important process in order to achieve a homogeneous distribution of second phase particles. in the present work, composite materials of M3/2 tool steel reinforced with 2.5,5 and 8 vol% of niobium carbide have been prepared. In order to ensure a homogeneous mix, powders of both materials were mixed by dry high-energy mechanical milling at 200 r.p.m. for 40 h. After a recovering annealing, two routes for consolidate were followed die pressing and vacuum sintering, and hot isostatic pressing (HIP). Pin-on-disc tests were carried out to evaluate wear behaviour in all the materials. Results show that ceramic particles additions improve wear resistance of base material. (Author) 9 refs

  6. TRADITIONAL METALLURGY, NANOTECHNOLOGIES AND STRUCTURAL MATERIALS: A SORBY AWARD LECTURE

    Energy Technology Data Exchange (ETDEWEB)

    Louthan, M

    2007-07-17

    Traditional metallurgical processes are among the many ''old fashion'' practices that use nanoparticles to control the behavior of materials. Many of these practices were developed long before microscopy could resolve nanoscale features, yet the practitioners learned to manipulate and control microstructural elements that they could neither see nor identify. Furthermore, these early practitioners used that control to modify microstructures and develop desired material properties. Centuries old colored glass, ancient high strength steels and medieval organ pipes derived many of their desirable features through control of nanoparticles in their microstructures. Henry Sorby was among the first to recognize that the properties of rocks, minerals, metals and organic materials were controlled by microstructure. However, Mr. Sorby was accused of the folly of trying to study mountains with a microscope. Although he could not resolve nanoscale microstructural features, Mr. Sorby's observations revolutionized the study of materials. The importance of nanoscale microstructural elements should be emphasized, however, because the present foundation for structural materials was built by manipulating those features. That foundation currently supports several multibillion dollar industries but is not generally considered when the nanomaterials revolution is discussed. This lecture demonstrates that using nanotechnologies to control the behavior of metallic materials is almost as old as the practice of metallurgy and that many of the emergent nanomaterials technologists are walking along pathways previously paved by traditional metallurgists.

  7. [Possible health effects associated with Pre-Columbian metallurgy].

    Science.gov (United States)

    Idrovo, Alvaro Javier

    2005-09-01

    In the Old World, several researchers have indicated that adverse health effects were associated with exposure to arsenic, and that this influenced a change in the use of copper-arsenic alloys to others less toxic. This hypothesis was evaluated for three Pre-Columbian metallurgy traditions: Central Andes, Intermediate Area, and West Mexico. The metal artifacts from the Central Andes showed arsenic concentrations similar to those in the Old World (0.5%-1.0%). In the Intermediate Area the values were smallest; however, in West Mexico the arsenic content was very high (7%-25%). In Central Andes arsenical bronze was used initially, but copper-tin alloys when introduced were preferred and distributed throughout the Inca Empire. Osteological and artistic evidences of foot amputations among Moche individuals from Central Andes support the presence of "black foot disease" (a condition associated with arsenic poisoning) among Pre-Columbian populations. In conclusion, the adverse effects of arsenic have been observed in the New World, and that these effects promoted a change toward the use of less toxic alloys.

  8. Indexation Rules for Metallurgy in PASCAL. Original Title: Regles d'Indexation de la Metallurgie'--Technical Note Issued by Informascience--January 1980. Translated by Marie Wallin.

    Science.gov (United States)

    Royal Inst. of Tech., Stockholm (Sweden). Library.

    The indexing rules presented are designed for use with a new French-German database on metallurgy being developed under an agreement by CNRS (Centre National de la Recherche Scientifique, Paris) and BAM (Bundesanstalt fur Materialprufung, Berlin). The new database, which will feature multilingual titles and index terms (French-German-English-) and…

  9. Ferrous ammonium phosphate (FeNH₄PO₄) as a new food fortificant: iron bioavailability compared to ferrous sulfate and ferric pyrophosphate from an instant milk drink.

    Science.gov (United States)

    Walczyk, Thomas; Kastenmayer, Peter; Storcksdieck Genannt Bonsmann, Stefan; Zeder, Christophe; Grathwohl, Dominik; Hurrell, Richard F

    2013-06-01

    The main purpose of this study was to establish bioavailability data in humans for the new (Fe) fortification compound ferrous ammonium phosphate (FAP), which was specially developed for fortification of difficult-to-fortify foods where soluble Fe compounds cannot be used due to their negative impact on product stability. A double-blind, randomized clinical trial with cross-over design was conducted to obtain bioavailability data for FAP in humans. In this trial, Fe absorption from FAP-fortified full-cream milk powder was compared to that from ferric pyrophosphate (FPP) and ferrous sulfate. Fe absorption was determined in 38 young women using the erythrocyte incorporation dual stable isotope technique (⁵⁷Fe, ⁵⁸Fe). Geometric mean Fe absorption from ferrous sulfate, FAP and FPP was 10.4, 7.4 and 3.3 %, respectively. Fe from FAP was significantly better absorbed from milk than Fe from FPP (p soluble reference compound (p = 0.0002). Absorption ratios of FAP and FPP relative to ferrous sulfate as a measure of relative bioavailability were 0.71 and 0.32, respectively. The results of the present studies show that replacing FPP with FAP in full-cream milk could significantly improve iron bioavailability.

  10. [Atmospheric emission of PCDD/Fs from secondary aluminum metallurgy industry in the southwest area, China].

    Science.gov (United States)

    Lu, Yi; Zhang, Xiao-Ling; Guo, Zhi-Shun; Jian, Chuan; Zhu, Ming-Ji; Deng, Li; Sun, Jing; Zhang, Qin

    2014-01-01

    Five secondary aluminum metallurgy enterprises in the southwest area of China were measured for emissions of PCDD/Fs. The results indicated that the emission levels of PCDD/Fs (as TEQ) were 0.015-0.16 ng x m(-3), and the average was 0.093 ng x m(-3) from secondary aluminum metallurgy enterprises. Emission factors of PCDD/Fs (as TEQ) from the five secondary aluminum metallurgy enterprises varied between 0.041 and 4.68 microg x t(-1) aluminum, and the average was 2.01 microg x t(-1) aluminum; among them, PCDD/Fs emission factors from the crucible smelting furnace was the highest. Congener distribution of PCDD/F in stack gas from the five secondary aluminum metallurgies was very different from each other. Moreover, the R(PCDF/PCDD) was the lowest in the enterprise which was installed only with bag filters; the R(PCDF/PCDD) were 3.8-12.6 (the average, 7.7) in the others which were installed with water scrubbers. The results above indicated that the mechanism of PCDD/Fs formation was related to the types of exhaust gas treatment device. The results of this study can provide technical support for the formulation of PCDD/Fs emission standards and the best available techniques in the secondary aluminum metallurgy industry.

  11. Potential for microbial oxidation of ferrous iron in basaltic glass.

    Science.gov (United States)

    Xiong, Mai Yia; Shelobolina, Evgenya S; Roden, Eric E

    2015-05-01

    Basaltic glass (BG) is an amorphous ferrous iron [Fe(II)]-containing material present in basaltic rocks, which are abundant on rocky planets such as Earth and Mars. Previous research has suggested that Fe(II) in BG can serve as an energy source for chemolithotrophic microbial metabolism, which has important ramifications for potential past and present microbial life on Mars. However, to date there has been no direct demonstration of microbially catalyzed oxidation of Fe(II) in BG. In this study, three different culture systems were used to investigate the potential for microbial oxidation of Fe(II) in BG, including (1) the chemolithoautotrophic Fe(II)-oxidizing, nitrate-reducing "Straub culture"; (2) the mixotrophic Fe(II)-oxidizing, nitrate-reducing organism Desulfitobacterium frappieri strain G2; and (3) indigenous microorganisms from a streambed Fe seep in Wisconsin. The BG employed consisted of clay and silt-sized particles of freshly quenched lava from the TEB flow in Kilauea, Hawaii. Soluble Fe(II) or chemically reduced NAu-2 smectite (RS) were employed as positive controls to verify Fe(II) oxidation activity in the culture systems. All three systems demonstrated oxidation of soluble Fe(II) and/or structural Fe(II) in RS, whereas no oxidation of Fe(II) in BG material was observed. The inability of the Straub culture to oxidize Fe(II) in BG was particularly surprising, as this culture can oxidize other insoluble Fe(II)-bearing minerals such as biotite, magnetite, and siderite. Although the reason for the resistance of the BG toward enzymatic oxidation remains unknown, it seems possible that the absence of distinct crystal faces or edge sites in the amorphous glass renders the material resistant to such attack. These findings have implications with regard to the idea that Fe(II)-Si-rich phases in basalt rocks could provide a basis for chemolithotrophic microbial life on Mars, specifically in neutral-pH environments where acid-promoted mineral dissolution and

  12. Effects of ferrous ions on the reductive dechlorination of trichloroethylene by zero-valent iron

    International Nuclear Information System (INIS)

    Liu, C.-C.; Tseng, D.-H.; Wang, C.-Y.

    2006-01-01

    The surface characteristics of zero-valent iron (ZVI) and the efficiency of reductive dechlorination of trichloroethylene (TCE) in the presence of ferrous ions were studied. The experimental results indicated that the acid-washing of a metallic iron sample enhanced the efficiency of TCE degradation by ZVI. This occurred because acid-washing changed the conformation of oxides on the surface of iron from maghemite (γ-Fe 2 O 3 ) to the more hydrated goethite (α-FeOOH), as was confirmed by XPS analysis. However, when ferrous ions were simultaneous with TCE in water, the TCE degradation rate decreased as the concentration of ferrous ion increased. This was due to the formation of passive precipitates of ferrous hydroxide, including maghemite and magnetite (Fe 3 O 4 ), that coated on the surface of acid-washed ZVI, which as a result inhibited the electron transfer and catalytic hydrogenation mechanisms. On the other hand, in an Fe 0 -TCE system without the acid-washing pretreatment of ZVI, ferrous ions were adsorbed into the maghemite lattice which was then converted to semiconductive magnetite. Thus, the electrons were transferred from the iron surface and passed through the precipitates, allowing for the reductive dechlorination of TCE

  13. Superplasticity in powder metallurgy aluminum alloys and composites

    International Nuclear Information System (INIS)

    Mishra, R.S.; Bieler, T.R.; Mukherjee, A.K.

    1995-01-01

    Superplasticity in powder metallurgy Al alloys and composites has been reviewed through a detailed analysis. The stress-strain curves can be put into 4 categories: classical well-behaved type, continuous strain hardening type, continuous strain softening type and complex type. The origin of these different types of is discussed. The microstructural features of the processed material and the role of strain have been reviewed. The role of increasing misorientation of low angle boundaries to high angle boundaries by lattice dislocation absorption is examined. Threshold stresses have been determined and analyzed. The parametric dependencies for superplastic flow in modified conventional aluminum alloys, mechanically alloyed alloys and Al alloy matrix composites is determined to elucidate the superplastic mechanism at high strain rates. The role of incipient melting has been analyzed. A stress exponent of 2, an activation energy equal to that for grain boundary diffusion and a grain size dependence of 2 generally describes superplastic flow in modified conventional Al alloys and mechanically alloyed alloys. The present results agree well with the predictions of grain boundary sliding models. This suggests that the mechanism of high strain rate superplasticity in the above-mentioned alloys is similar to conventional superplasticity. The shift of optimum superplastic strain rates to higher values is a consequence of microstructural refinement. The parametric dependencies for superplasticity in aluminum alloy matrix composites, however, is different. A true activation energy of superplasticity in aluminum alloy matrix composites, however, is different. A true activation energy of 313 kJ/mol best describes the composites having SiC reinforcements. The role of shape of the reinforcement (particle or whisker) and processing history is addressed. The analysis suggests that the mechanism for superplasticity in composites is interface diffusion controlled grain boundary sliding

  14. Corrosion inhibition of powder metallurgy Mg by fluoride treatments.

    Science.gov (United States)

    Pereda, M D; Alonso, C; Burgos-Asperilla, L; del Valle, J A; Ruano, O A; Perez, P; Fernández Lorenzo de Mele, M A

    2010-05-01

    Pure Mg has been proposed as a potential degradable biomaterial to avoid both the disadvantages of non-degradable internal fixation implants and the use of alloying elements that may be toxic. However, it shows excessively high corrosion rate and insufficient yield strength. The effects of reinforcing Mg by a powder metallurgy (PM) route and the application of biocompatible corrosion inhibitors (immersion in 0.1 and 1M KF solution treatments, 0.1M FST and 1M FST, respectively) were analyzed in order to improve Mg mechanical and corrosion resistance, respectively. Open circuit potential measurements, polarization techniques (PT), scanning electrochemical microscopy (SECM) and electrochemical impedance spectroscopy (EIS) were performed to evaluate its corrosion behavior. SECM showed that the local current of attacked areas decreased during the F(-) treatments. The corrosion inhibitory action of 0.1M FST and 1M FST in phosphate buffered solution was assessed by PT and EIS. Under the experimental conditions assayed, 0.1M FST revealed better performance. X-ray photoelectron spectroscopy, energy dispersive X-ray and X-ray diffraction analyses of Mg(PM) with 0.1M FST showed the presence of KMgF(3) crystals on the surface while a MgF(2) film was detected for 1M FST. After fluoride inhibition treatments, promising results were observed for Mg(PM) as degradable metallic biomaterial due to its higher yield strength and lower initial corrosion rate than untreated Mg, as well as a progressive loss of the protective characteristics of the F(-)-containing film which ensures the gradual degradation process. Copyright (c) 2009 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

  15. Progress report of the Metallurgy Division for the period 1978-1980

    International Nuclear Information System (INIS)

    Sharma, B.D.; Mohan, Ashok; Bose, D.K.; Rao, C.N.; Chouthai, S.S.

    1980-01-01

    The research and development (R and D) work of the Metallurgy Division of the Bhabha Atomic Research Centre at Bombay for the period 1978-1980 is reported in the form of individual summaries under the headings: extractive metallurgy section, physical metallurgy section, corrosion and electrometallurgy section, ceramics section. Progress of work of beryllium pilot plant project, programme for R-5 utilisation for materials irradiation research project, development of rare, reactive and refractory metals, and development of ceramics materials for MHD programme is surveyed. Lists of publications, deputations, visits, conferences, colloquia are given. A chart at the end shows the various sections of the Division and personnel in each section. (M.G.B.)

  16. Introduction to powder metallurgy processes for titanium manufacturing; Introduccion al procesado pulvimetalurgico del titanio

    Energy Technology Data Exchange (ETDEWEB)

    Esteban, P. G.; Bolzoni, L.; Ruiz-Navas, E. M.; Gordo, E.

    2011-07-01

    The development of new extraction processes to produce titanium in powder form leads Powder Metallurgy to an advantage position among the manufacturing processes for titanium. The cost reduction of base material, coupled with the economy of the powder metallurgy processes, give titanium industry the chance to diversify its products, which could lead to production volumes able to stabilise the price of the metal. This work reviews some of the Powder Metallurgy techniques for the manufacturing of titanium parts, and describes the two typical approaches for titanium manufacturing: Blending Elemental and Prealloyed Powders. Among others, conventional pressing and sintering are described, which are compared with cold and hot isostatic pressing techniques. Real and potential applications are described. (Author) 71 refs.

  17. 76 FR 64344 - Amended Record of Decision for the Nuclear Facility Portion of the Chemistry and Metallurgy...

    Science.gov (United States)

    2011-10-18

    ... the same sets of safety controls and key equipment. Further, as the SEIS analysis indicates, once... Nuclear Facility Portion of the Chemistry and Metallurgy Research Building Replacement Project at Los...) for the Nuclear Facility portion of the Chemistry and Metallurgy Research Building Replacement (CMRR...

  18. Hydrometallurgical-UV process to produce ferrous sulfate from the pyrite present in coal tailings

    Energy Technology Data Exchange (ETDEWEB)

    Viganico, E.M.; Silva, R.A. [South Rio Grande Federal Univ., Porto Alegre (Brazil).Graduate Program in Mining, Metallurgical and Materials Technology Center

    2010-07-01

    The oxidation of pyrite can promote acid mine drainage (AMD). This study developed a hydrometallurgical-UV route for the production of ferrous sulfate. The laboratory study was conducted using a pyrite concentrate obtained from a processed coal tailing. Leaching of the tailing was performed in packed bed columns in an oxidizing environment with an aqueous medium. Recirculation of the liquor produced an Fe{sup 3+} iron rich extract. Ultraviolet irradiation was then used to convert the Fe{sup 3+} to Fe{sup 2+}. Heat provided by the UV lamps caused the ferrous sulfate to crystallize. X-ray diffraction (XRD) studies of the crystals demonstrated that it is possible to produce commercial-grade ferrous sulfate heptahydrate crystals from the pyrite present in coal tailings. The crystals are used to treat anemia in humans and animals, and are also used as reagents for waste and waste water treatment. 7 refs., 2 tabs., 2 figs.

  19. Modernization of the Ural Metallurgy during the Great Patriotic War (1941–1945

    Directory of Open Access Journals (Sweden)

    Vladimir V. Zaparii

    2013-09-01

    Full Text Available The article characterizes the Ural industry modernization in war footing, shows the significance of evacuation of enterprises from the Western areas of the country to the region, reveals their role in the formation of a new metallurgical center of modern metallurgy in terms of human resources and manufacture. Innovations in metallurgy, the role of human factor in solving industrial restructuring problem are examined. Forms and methods of science use for the industrial modernization are considered. Solving of human resources problem is shown. The author touches upon the problem of metallurgical sector management in wartime. The role of people’s heroism in this difficult period of Russian history is discussed.

  20. Metallurgy of high-silicon steel parts produced using Selective Laser Melting

    OpenAIRE

    Garibaldi, Michele; Ashcroft, Ian; Simonelli, Marco; Hague, Richard

    2016-01-01

    The metallurgy of high-silicon steel (6.9%wt.Si) processed using Selective Laser Melting (SLM) is presented for the first time in this study. High-silicon steel has great potential as a soft magnetic alloy, but its employment has been limited due to its poor workability. The effect of SLM-processing on the metallurgy of the alloy is investigated in this work using microscopy, X-Ray Diffraction (XRD) and Electron Backscatter Diffraction (EBSD). XRD analysis suggests that the SLM high-silicon s...

  1. [Analysis of changes in characteristics of arterial hypertension occupational risk in workers of nonferrous metallurgy].

    Science.gov (United States)

    Vlasova, E M; Shliapnikov, D M; Lebedeva, T M

    2015-01-01

    The article covers changes in occupational cardiovascular risk for workers of nonferrous,metallurgy. Findings are that exposure to noise up to 94 dB with length of service increases possible atherosclerosis and metabolic syndrome. With 5 years of service, risk of the predicted conditions increases by 40.5%. When occupational exposure lasts over 5 years, risk of arterial hypertension increases. A group of workers without exposure to occupational factors appeared to have no connection between length of service and metabolic syndrome and arterial hypertension. Risk evolution modelling proved that risk of functional disorders in nonferrous metallurgy workers becomes unacceptable after 5 years of service (cardiovascular disorders are critical).

  2. New Equation for Prediction of Martensite Start Temperature in High Carbon Ferrous Alloys

    Science.gov (United States)

    Park, Jihye; Shim, Jae-Hyeok; Lee, Seok-Jae

    2018-02-01

    Since previous equations fail to predict M S temperature of high carbon ferrous alloys, we first propose an equation for prediction of M S temperature of ferrous alloys containing > 2 wt pct C. The presence of carbides (Fe3C and Cr-rich M 7C3) is thermodynamically considered to estimate the C concentration in austenite. Especially, equations individually specialized for lean and high Cr alloys very accurately reproduce experimental results. The chemical driving force for martensitic transformation is quantitatively analyzed based on the calculation of T 0 temperature.

  3. Multifactorial study and kinetics of signal development in ferrous-methylthymol blue-gelatin gel dosimeters.

    Science.gov (United States)

    Penev, Kalin I; Mequanint, Kibret

    2017-05-01

    To develop and characterize a ferrous-methylthymol blue-gelatin gel dosimeter with low optical background and appropriate additives for reduced rate of auto-oxidation and diffusion. A mixed-level multifactorial design of experiments was used to test the effects of the concentrations of sulfuric acid, 5-nitro-1,10-phenanthroline (Nn), and glyoxal (Gx) on the background absorbance, dose sensitivity, and auto-oxidation of the tested gel dosimeter. The dosimetric properties of the proposed ferrous-methylthymol blue-gelatin dosimeter, doped with Nn and Gx, were compared with the undoped formulation and with ferrous-xylenol orange-gelatin gel dosimeters. Irradiations were performed in both small-scale cuvette samples and large 400-mL bulk samples. In addition to that, a new kinetic model for the signal development postirradiation was derived based on chemical principles and used for comparison of the different formulations. The new formulation showed a reduced auto-oxidation rate, while maintaining low background absorbance relative to the common ferrous-xylenol orange-gelatin gel dosimeter. Compared with undoped ferrous-xylenol orange or ferrous-methylthymol blue gels, the dose sensitivity of the new formulation is approximately 2 to 3 times lower, but remains clinically adequate. A previously unreported dose rate dependence of the dose sensitivity was observed, and a new kinetic model for the signal development postirradiation was used to investigate this effect. Similar dose rate dependences in gels containing either methylthymol blue or xylenol orange, with or without doping with Nn and Gx, were observed, suggesting that the low ferrous ammonium sulfate concentrations used in studied formulations were responsible for this effect. A multifactorial design of experiments and a new kinetic model for the signal development postirradiation were successfully employed to optimize the composition and characterize the properties of a new ferrous-methylthymol blue-gelatin gel

  4. Executive committee

    Science.gov (United States)

    Xiao, Guoqing; Cai, Xiaohong; Ding, Dajun; Ma, Xinwen; Zhao, Yongtao

    2014-04-01

    ChairVice Chair Toshiyuki AzumaRoberto Rivarola Atomic, Molecular & Optical Physics LabUniversidad Nacional de Rosario and Advanced Science InstituteInstituto de Fisica Rosario RIKEN, JapanRosario, Argentina SecretaryMembers Dominique VernhetJoachim Burgdörfer, Austria Institut des NanoSciences de Paris Birgit Lohmann, Australia Université Pierre et Marie Curie Hossein Sadeghpour, USA Paris, FranceThomas Stöhlker, Germany Past ChairJim McCann, UK Barry DunningGuoqing Xiao, China Physics & AstronomyXiaohong Cai, China Rice University, HoustonXinwen Ma, China Texas, USAYongtao Zhao, China TreasurerFernando Martin, Spain Henrik CederquistLuis Mendez, Spain Alba Nova University CenterAnatoli Kheifets, Australia Stockholm University Stockholm, Sweden Details of the general committee are available in the PDF

  5. Metallurgy, environmental pollution and the decline of Etruscan civilisation.

    Science.gov (United States)

    Harrison, Adrian P; Cattani, Ilenia; Turfa, Jean M

    2010-01-01

    The Etruscans were justifiably famous in antiquity for their advanced metallurgy and for the rich mineral resources of their region (including La Tolfa, the Colline Metallifere, Mont'Amiata and Elba). We offer a new perspective on certain Iron Age and Archaic (ca. 1,000-480 BC: ) Etruscan industrial and habitation sites, and on the problem of heavy metal poisoning, still being investigated today, coincidentally in some of the same areas that originally saw Etruscan mines and workshops. This study investigates ancient sources, including literature and excavation reports, in the light of modern studies of heavy metal poisoning on human beings, plant and animal life. Furthermore, it is the first to use non-invasive Niton X-ray fluorescence analysis of samples of Etruscan (strictly ethnically Faliscan) hair (c. 350 BCE: ). The findings show the strong likelihood of heavy metal poisoning in areas of Etruscan metallurgical activity with the effects of this being responsible for or contributing to the abandonment of a number of these sites around the 6th century BC: . No thoroughly satisfactory explanation of this phenomenon has previously been offered. However, findings suggest that Faliscan women, represented by sample CG 2004-6-2, were not exposed to high levels of arsenic in life, which is not perhaps surprising for an urban aristocratic woman of the mid-4th century BC: . The reasons for the abandonment of several flourishing settlements are without doubt complex, and include political and social change. We suggest heavy metal contamination as an additional stimulus to the noted phenomenon of the peaceful abandonment, at the beginning, and at the end of the 6th century BC: , of sites in southern and northern Etruria such as Marsiliana d'Albegna (late 7th c.), Lago dell'Accesa, Acquarossa and Poggio Civitate-Murlo (late 6th c.). While the historical truth of the demise of Etruscan civilisation is much more complex, an interim set of related events, the desertion of

  6. Effects of differences in the timing of ferrous sulfate supplementation on lipid peroxidation and activation of NF-κB in the placenta of pregnant rats

    Directory of Open Access Journals (Sweden)

    Alfi Noviyana

    2017-10-01

    Conclusion: In conclusion, administration of ferrous sulfate will induce placental oxidative damage. Increased activation of NF-κB is underlain by changes in the degree of oxidative stress in the placenta from administration of ferrous sulfate.

  7. Uranium mining and metallurgy library science and technology literature retrieval of network

    International Nuclear Information System (INIS)

    Tang Lilei

    2014-01-01

    This paper introduces the network resources and characteristics retrieve service of Beijing research Institute of Chemical Engineering of Metallurgy library, Analyzes the problems often encountered in the literature retrieval in science and technology, And puts forward the solution, Puts forward the thinking and Suggestions of science and technology literature retrieval. (author)

  8. Solvent Extraction of Copper: An Extractive Metallurgy Exercise for Undergraduate Teaching Laboratories

    Science.gov (United States)

    Smellie, Iain A.; Forgan, Ross S.; Brodie, Claire; Gavine, Jack S.; Harris, Leanne; Houston, Daniel; Hoyland, Andrew D.; McCaughan, Rory P.; Miller, Andrew J.; Wilson, Liam; Woodhall, Fiona M.

    2016-01-01

    A multidisciplinary experiment for advanced undergraduate students has been developed in the context of extractive metallurgy. The experiment serves as a model of an important modern industrial process that combines aspects of organic/inorganic synthesis and analysis. Students are tasked to prepare a salicylaldoxime ligand and samples of the…

  9. Metallurgy department progress report for the period 1 January to 31 December 1981

    International Nuclear Information System (INIS)

    1982-07-01

    The activities of the Metallurgy Department at Risoe during 1981 are described. The work is presented in three chapters: General Materials Research, Technology and Materials Development, Fuel Elements. Furthermore, a survey is given of the department's participation in international collaboration and of its activities within education and training. A list (with abstracts) of publications and lectures by the staff during 1981 is included. (author)

  10. Metallurgy department progress report for the period 1 January to 31 December 1982

    International Nuclear Information System (INIS)

    1983-07-01

    The activities of the Metallurgy Department at Risoe during 1982 are described. The work is presented in three chapters: General Materials Research, Technology and Materials Deveopment, Fuel Elements. Furthermore, a survey is given of the department's participation in international collaboration and of its activities within education and training. A list (with abstracts) of publications and lectures by the staff during 1982 is included. (author)

  11. Powder metallurgy preparation of Al-Cu-Fe quasicrystals using mechanical alloying and Spark Plasma Sintering

    Czech Academy of Sciences Publication Activity Database

    Novák, P.; Kubatík, Tomáš František; Vystrčil, J.; Hendrych, R.; Kříž, J.; Mlynár, J.; Vojtěch, D.

    2014-01-01

    Roč. 52, September (2014), s. 131-137 ISSN 0966-9795 Institutional support: RVO:61389021 Keywords : Nanostructure intermetallics * Ternary alloys systems * Mechanical alloying and milling * Sintering * Diffraction Subject RIV: JG - Metallurgy Impact factor: 2.131, year: 2014 http://www.sciencedirect.com/science/article/pii/S0966979514001198#

  12. Recycling of wastes from uranium mining and metallurgy and recovery of useful resources in China

    International Nuclear Information System (INIS)

    Pan Yingjie; Xue Jianxin; Chen Zhongqiu

    2012-01-01

    Recycling of wastes from uranium mining and metallurgy in China and recovery of useful resources are summarized from the aspects such as recovery of uranium from mine water, reusing of waste water, decontaminating and recycling of radioactivity contaminated metal, backfill of gangues and tailings, and comprehensive recovery and utilization of associated uranium deposits. (authors)

  13. Practical application of solid phase spectrophotometry in analysis of materials and goods of mining and metallurgy

    International Nuclear Information System (INIS)

    Duan Qunzhang

    1999-01-01

    The author reviewed recent development and practical application of solid phase spectrophotometry in analysis of materials and goods of mining-metallurgy. Separation and preconcentration and conditions of coloring determination, sensitivity and range of detection, as well as interference of corresponding method are discussed

  14. Annual report of the Metallurgy Division [for the] period ending December 1977

    International Nuclear Information System (INIS)

    Elayaperumal, K.; Sridhar Rao, Ch.; Mukhopadhyay, P.; Rao, S.V.K.

    1979-01-01

    The research and development work carried out and the various programmes underway in the Metallurgy Division of the Bhabha Atomic Research Centre, Bombay, during the calendar year 1977 have been reported. The R and D work and programmes cover extraction metallurgy, physical metallurgy, alloy development, corrosion metallurgy and ceramics. Some of the major studies and programmes are: (1) development of processes for extraction of niobium, vanadium, hafnium and nickel, (2) preparation of niobium alloys, ferro-zirconium, ceramic grade zirconia, (3) electro-refining of zircaloy scrap, (4) preparation of anhydrous beryllium fluoride from Indian beryl, (5) preparation of beryllium alloys, (6) studies on phase transformation and deformation behaviour of zirconium and zirconium-oxygen alloys, (7) self-diffusion studies in dilute Zr-Fe and Zr-Cr alloys, (8) studies on corrosion and stress corrosion cracking of zirconium base alloys and (9) sintering studies on ZrO 2 -PuO 2 and BeO. (M.G.B.)

  15. Metallurgy Department progress report for the period 1 January to 31 December 1984

    International Nuclear Information System (INIS)

    1985-04-01

    The activities of the Metallurgy Department at Risoe during 1984 are described. The work is presented in three chapters: General Materials Research, Technology and Materials Development, and Fuel Elements. A survey is given of the Department's participation in international collaboration and of its activities within education and training. A list (with abstracts) of publications and lectures by the staff during 1984 is included. (author)

  16. Powder Metallurgy Preparation of Co-Based Alloys for Biomedical Applications

    Czech Academy of Sciences Publication Activity Database

    Marek, I.; Novák, P.; Mlynár, J.; Vojtěch, D.; Kubatík, Tomáš František; Málek, J.

    2015-01-01

    Roč. 128, č. 4 (2015), s. 597-601 ISSN 0587-4246. [International Symposium on Physics of Materials (ISPMA) /13./. Prague, 31.08.2014-04.09.2014] Institutional support: RVO:61389021 Keywords : powder metallurgy * mechanical properties * biomedical applications Subject RIV: JK - Corrosion ; Surface Treatment of Materials Impact factor: 0.525, year: 2015

  17. Mechanical properties of modified low cobalt powder metallurgy Udimet 700 type alloys

    Science.gov (United States)

    Harf, Fredric H.

    1989-01-01

    Eight superalloys derived from Udimet 700 were prepared by powder metallurgy, hot isostatically pressed, heat treated and their tensile and creep rupture properties determined. Several of these alloys displayed properties superior to those of Udimet 700 similarly prepared, in one case exceeding the creep rupture life tenfold. Filter clogging by extracted gamma prime, its measurement and significance are discussed in an appendix.

  18. Ice-core evidence of earliest extensive copper metallurgy in the Andes 2700 years ago.

    Science.gov (United States)

    Eichler, A; Gramlich, G; Kellerhals, T; Tobler, L; Rehren, Th; Schwikowski, M

    2017-01-31

    The importance of metallurgy for social and economic development is indisputable. Although copper (Cu) was essential for the wealth of pre- and post-colonial societies in the Andes, the onset of extensive Cu metallurgy in South America is still debated. Comprehensive archaeological findings point to first sophisticated Cu metallurgy during the Moche culture ~200-800 AD, whereas peat-bog records from southern South America suggest earliest pollution potentially from Cu smelting as far back as ~2000 BC. Here we present a 6500-years Cu emission history for the Andean Altiplano, based on ice-core records from Illimani glacier in Bolivia, providing the first complete history of large-scale Cu smelting activities in South America. We find earliest anthropogenic Cu pollution during the Early Horizon period ~700-50 BC, and attribute the onset of intensified Cu smelting in South America to the activities of the central Andean Chiripa and Chavin cultures ~2700 years ago. This study provides for the first time substantial evidence for extensive Cu metallurgy already during these early cultures.

  19. A Guide for Planning Facilities for Occupational Preparation Programs in Metallurgy Technology. Interim Report. Research 28.

    Science.gov (United States)

    German, Carl, Jr.

    The major purpose of this guide is to elicit the information necessary for writing educational specifications for facilities to house technical education programs in metallurgy. It is organized in these parts: (1) Part I discusses the major purpose, underlying assumptions, recent instructional trends, and guiding principles utilized in the…

  20. Microstructural and mechanical properties of biodegradable iron foam prepared by powder metallurgy

    Czech Academy of Sciences Publication Activity Database

    Čapek, Jaroslav; Vojtěch, D.; Oborná, A.

    2015-01-01

    Roč. 83, Oct (2015), s. 468-482 ISSN 0261-3069 R&D Projects: GA ČR GBP108/12/G043 Institutional support: RVO:68378271 Keywords : powder metallurgy * metallic foams * biodegradable iron * mechanical properties * scaffolds Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 3.997, year: 2015

  1. Powder metallurgy approaches to high temperature components for gas turbine engines

    Science.gov (United States)

    Probst, H. B.

    1974-01-01

    Research is reported for the tensile strength, ductility, and heat performance characterisitics of powder metallurgy (p/m) superalloys. Oxide dispersion strengthened alloys were also evaluated for their strength during thermal processing. The mechanical attributes evident in both p/m supperalloys and dispersion strengthened alloys are discussed in terms of research into their possible combination.

  2. Power metallurgy approaches to high temperature components for gas turbine engines

    Science.gov (United States)

    Probst, H. B.

    1974-01-01

    Work conducted by NASA and NASA contractors on prealloyed superalloy powders and materials strengthened by oxide dispersion is reviewed. Fabrication, tensile strength, superplasticity, grain growth control, stress rupture life, and grain-size and dispersion-level effects are covered. Distinct strength advantages of powder metallurgy superalloys over conventional wrought alloys are noted.

  3. [Concomitant influence of occupational and social risk factors on health of workers engaged into powder metallurgy].

    Science.gov (United States)

    Shur, P Z; Zaĭtseva, N V; Kostarev, V G; Lebedeva-Nesevria, N A; Shliapnikov, D M

    2012-01-01

    Results of health risk evaluation in workers engaged into powder metallurgy, using complex of hygienic, medical, epidemiologic and sociologic studies, enable to define priority occupational and social risk factors, to assess degree of their influence on the workers' health and to identify occupationally induced diseases.

  4. The effect of initial pH on the kinetics of ferrous-iron biooxidation at ...

    African Journals Online (AJOL)

    The general understanding in bioleaching of sulphide minerals is to keep pH low. A number of published articles have reported the effect of pH on biooxidation rates of ferrous-iron and/or sulphur by bioleaching microbes, although most of these studies were conducted at optimum or near optimum temperature for microbial ...

  5. Eddy Current Separation of Fine Non-Ferrous Particles from Bulk Streams

    NARCIS (Netherlands)

    Settimo, F.; Bevilacqua, P.; Rem, P.

    2004-01-01

    Recovery of fine non-ferrous metals from waste streams is a notoriously difficult problem in eddy current separation technology. Existing processes either have a low capacity or an incomplete recovery for particle sizes below 5 mm. In a new process, the particles are fed slightly wet to make them

  6. Compatibility of Anti-Wear Additives with Non-Ferrous Engine Bearing Alloys

    Energy Technology Data Exchange (ETDEWEB)

    Qu, Jun [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Zhou, Yan [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

    2017-01-01

    Investigate the compatibility of engine lubricant antiwear (AW) additives, specifically conventional zinc dialkyldithiophosphate (ZDDP) and newly developed ionic liquids (ILs), with selected non-ferrous engine bearing alloys, specifically aluminum and bronze alloys that are commonly used in connecting rod end journal bearings and bushings, to gain fundamental understanding to guide future development of engine lubricants

  7. Stabilization of Pb and As in soils by applying combined treatment with phosphates and ferrous iron.

    Science.gov (United States)

    Xenidis, Anthimos; Stouraiti, Christina; Papassiopi, Nymphodora

    2010-05-15

    The chemical immobilization of Pb and As in contaminated soil from Lavrion, Greece, using monocalcium phosphate and ferrous sulfate as stabilizing agents was investigated. Monocalcium phosphate was added to contaminated soil at PO(4) to Pb molar ratios equal to 0, 0.5, 1, 1.5 and 2.5, whereas ferrous sulfate was added at Fe to As molar ratios equal to 0, 2.5, 5, 10 and 20. Phosphates addition to contaminated soil decreased Pb leachability, but resulted in significant mobilization of As. Simultaneous immobilization of Pb and As was obtained only when soil was treated with mixtures of phosphates and ferrous sulfate. Arsenic uptake by plants was also seen to increase when soil was treated only with phosphates, but co-addition of ferrous sulfate was efficient in maintaining As phytoaccumulation at low levels. The addition of at least 1.5M/M phosphates and 10M/M iron sulfate to soil reduced the dissolved levels of Pb and As in the water extracts to values in compliance with the EU drinking water standards. However, both additives contributed in the acidification of soil, decreasing pH from 7.8 to values as low as 5.6 and induced the mobilization of pH sensitive elements, such as Zn and Cd. Copyright (c) 2010 Elsevier B.V. All rights reserved.

  8. Kinetics of Adsorption of Ferrous Ion onto Acid Activated Carbon from Zea Mays Dust

    Directory of Open Access Journals (Sweden)

    P. K. Baskaran

    2011-01-01

    Full Text Available The batch removal of ferrous ion from aqueous solution using low cost adsorbents such as zea mays dust carbon(ZDC under different experimental conditions were investigated in this study. The process parameters studied include agitation time, initial metal ion concentration, carbon dose, pH and temperature. The adsorption followed first order reaction equation and the rate is mainly controlled by intraparticle diffusion. Freundlich and Langmuir isotherm models were applied to the equilibrium data. The adsorption capacity (Qm obtained from the Langmuir isotherm plot were found to 37.17, 38.31, 39.37 and 40.48 mg/g. The temperature variation study showed that the ferrous ions adsorption is endothermic and spontaneous with increased randomness at the solid solution interface. Significant effect on adsorption was observed on varying the pH of the ferrous ion solutions. The Langmuir and Freundlich adsorption isotherms obtained positive ΔH0 value, pH dependent results and desorption of metal ions in mineral acid suggest that the adsorption of ferrous ion on ZDC involves physisorption mechanism.

  9. Bioextraction of Copper from Printed Circuit Boards: Influence of Initial Concentration of Ferrous Iron

    Science.gov (United States)

    Yamane, Luciana Harue; Espinosa, Denise Crocce Romano; Tenório, Jorge Alberto Soares

    Printed circuit boards are found in all electric and electronic equipment and are particularly problematic to recycle because of the heterogeneous mix of organic material, metals, and fiberglass. Additionally, printed circuit boards can be considered a secondary source of copper and bacterial leaching can be applied to copper recovery. This study investigated the influence of initial concentration of ferrous iron on bacterial leaching to recover copper from printed circuit boards using Acidithiobacillus ferrooxidans-LR. Printed circuit boards from computers were comminuted using a hammer mill. The powder obtained was magnetically separated and the non magnetic material used in this study. A shake flask study was carried out on the non magnetic material using a rotary shaker at 30°C, 170 rpm and different initial concentrations of ferrous iron (gL-1): 6.75; 13.57 and 16.97. Abiotic controls were also run in parallel. The monitored parameters were pH, Eh, ferrous iron concentration and copper extraction (spectroscopy of atomic absorption). The results showed that using initial concentration of ferrous iron of 6.75gL-1 were extracted 99% of copper by bacterial leaching.

  10. A novel reverse osmosis membrane by ferrous sulfate assisted controlled oxidation of polyamide layer

    Science.gov (United States)

    Raval, Hiren D.; Raviya, Mayur R.; Gauswami, Maulik V.

    2017-11-01

    With growing desalination capacity, it is very important to evaluate the performance of thin film composite reverse osmosis (TFC RO) membrane in terms of energy consumption for desalination. There is a trade-off between salt rejection and water-flux of TFC RO membrane. This article presents a novel approach of analyzing the effect of mixture of an oxidizing agent sodium hypochlorite and a reducing agent ferrous sulfate on virgin TFC RO membrane. Experiments were carried out by varying the concentrations of both sodium hypochlorite and ferrous sulfate. The negative charge was induced on the membrane due to the treatment of combination of sodium hypochlorite and ferrous sulfate, thereby resulting in higher rejection of negative ions due to repulsive force. Membrane treated with 1000 mg l-1 sodium hypochlorite and 2000 mg l-1 ferrous sulfate showed the best salt rejection i.e. 96.23%. The characterization was carried out to understand the charge on the membrane surface by Zeta potential, morphology of membrane surface by scanning electron microscope (SEM), surface roughness features by atomic force microscope (AFM) and chemical structural changes by nuclear magnetic resonance (NMR) analysis.

  11. Effect of ferrous/ferric ions molar ratio on reaction mechanism for ...

    Indian Academy of Sciences (India)

    Magnetite nanoparticles were prepared by hydrothermal synthesis under various initial ferrous/ferric molar ratios without adding any oxidizing and reducing agents in order to clarify effects of the molar ratio on the reaction mechanism for the formation of magnetite nanoparticles. The magnetite nanoparticles prepared were ...

  12. Wear resistance of alloy вт-22 with non-ferrous alloys at reverse

    Directory of Open Access Journals (Sweden)

    А.М. Хімко

    2010-01-01

    Full Text Available  The article presents the results of tests of non hardened titanium alloy ВТ-22 with aviation non-ferrous alloys in reverse sliding friction. The main objective of the work is the selection of the optimum combination of materials depending on changes in loading conditions. Study of alloy ВТ-22 wear resistance was carried out in pairs with БрОФ-10-1, БрБ2, БрАЖ-9-4, ВТ-22, МЛ5, Д16Т, 7Х21ГАН5Ш and 95Х18Ш. The dependencies of the materials wear at pressures 10, 20 and 30 Mpa we determined. The linear nature of titanium alloy wear curves indicates that the change in the wear mechanism occurs gradually. The histograms of non-ferrous materials wear and the total wear of the friction pair are presented. It is established that the bronze БрАЖ-9-4 is the most preferable material for contact with non hardened titanium alloy ВТ-22, the least wear among the tested materials. The established coefficients of the titanium alloy ВТ-22 friction in pair with aviation structural non-ferrous alloys are presented. The results of research will be relevant for the engineering industry, where non hardened titanium alloy ВТ-22 in pair with non-ferrous alloys is applied.

  13. Mechanism of radiation and thermal decomposition of sulphide non-ferrous metals

    International Nuclear Information System (INIS)

    Mazhrenova, N.P.

    1998-01-01

    This paper deals with the non-ferrous metals sulfides in term of their radiative sensitivity, directed chances of their physical-chemical, and hence technological properties by radiation influence both on sulfide materials and on the processes with their participation. (author)

  14. Prerequisites and opportunities for repositioning of the Urals metallurgy within the Industry 4.0

    Directory of Open Access Journals (Sweden)

    O. A. Romanova

    2017-12-01

    Full Text Available The authors present the modern trends in the development of metallurgy, and classify the technological structure of metallurgical industry. The article contains specific features of the development of metallurgy in the conditions of industry formation. A special role in this process plays the pace of digitalization and robotization of the industry, the development of additive technologies, Internet of things. The authors substantiate the possibility of developing the metallurgy of the Middle Urals as a science-intensive, high-tech complex that meets the requirements of Industry 4.0. This possibility interrelates with its repositioning, one of the main tasks of which is the formation of new sales markets focused on high-tech consumer industries, as well as the preservation of traditional consumption sectors under conditions of increasing competition in the construction materials market. The authors underline the importance of international cooperation in the field of environmentally safe industrial development, with applying the best available technologies and innovative development in general. The authors propose a methodological approach for assessing the repositioning of the regional metallurgical complex. This approach is the consecutive implementation of the following stages: assessment of dynamics and the forecast of development of consumer steel products sector and its structure based on identified priority areas of technological development of metallurgy in the region; construction of a factor model describing the changes in parameters of the RMC repositioning process, and approximation of the characteristics of their nonlinear elements; building a mathematical model on the basis of neural network algorithms for assessing the process of repositioning the RMC, taking into account projected values of the RMK parameters in the process of repositioning and changing the structure of consumer markets for metal products; formation of a variable

  15. Oxidative Alteration of Ferrous Smectites and Implications for the Redox Evolution of Early Mars

    Science.gov (United States)

    Chemtob, Steven M.; Nickerson, Ryan D.; Morris, Richard V.; Agresti, David G.; Catalano, Jeffrey G.

    2017-12-01

    Surface conditions on early Mars were likely anoxic, similar to early Earth, but the timing of the evolution to oxic conditions characteristic of contemporary Mars is unresolved. Ferrous trioctahedral smectites are the thermodynamically predicted products of anoxic basalt weathering, but orbital analyses of Noachian-aged terrains find primarily Fe3+-bearing clay minerals. Rover-based detection of Fe2+-bearing trioctahedral smectites at Gale Crater suggests that ferrous smectites are the unoxidized progenitors of orbitally detected ferric smectites. To assess this pathway, we conducted ambient-temperature oxidative alteration experiments on four synthetic ferrous smectites having molar Fe/(Mg + Fe) from 1.00 to 0.33. Smectite suspension in air-saturated solutions produced incomplete oxidation (24-38% Fe3+/ΣFe). Additional smectite oxidation occurred upon reexposure to air-saturated solutions after anoxic hydrothermal recrystallization, which accelerated cation and charge redistribution in the octahedral sheet. Oxidation was accompanied by contraction of the octahedral sheet (d(060) decreased from 1.53-1.56 Å to 1.52 Å), consistent with a shift toward dioctahedral structure. Ferrous smectite oxidation by aqueous hydrogen peroxide solutions resulted in nearly complete Fe2+ oxidation but also led to partial Fe3+ ejection from the structure, producing nanoparticulate hematite. Reflectance spectra of oxidized smectites were characterized by (Fe3+,Mg)2-OH bands at 2.28-2.30 μm, consistent with oxidative formation of dioctahedral nontronite. Accordingly, ferrous smectites are plausible precursors to observed ferric smectites on Mars, and their presence in late-Noachian sedimentary units suggests that anoxic conditions may have persisted on Mars beyond the Noachian.

  16. Effect of calcium oxide on the efficiency of ferrous ion oxidation and total iron precipitation during ferrous ion oxidation in simulated acid mine drainage treatment with inoculation of Acidithiobacillus ferrooxidans.

    Science.gov (United States)

    Liu, Fenwu; Zhou, Jun; Jin, Tongjun; Zhang, Shasha; Liu, Lanlan

    2016-01-01

    Calcium oxide was added into ferrous ion oxidation system in the presence of Acidithiobacillus ferrooxidans at concentrations of 0-4.00 g/L. The pH, ferrous ion oxidation efficiency, total iron precipitation efficiency, and phase of the solid minerals harvested from different treatments were investigated during the ferrous ion oxidation process. In control check (CK) system, pH of the solution decreased from 2.81 to 2.25 when ferrous ions achieved complete oxidation after 72 h of Acidithiobacillus ferrooxidans incubation without the addition of calcium oxide, and total iron precipitation efficiency reached 20.2%. Efficiency of ferrous ion oxidation and total iron precipitation was significantly improved when the amount of calcium oxide added was ≤1.33 g/L, and the minerals harvested from systems were mainly a mixture of jarosite and schwertmannite. For example, the ferrous ion oxidation efficiency reached 100% at 60 h and total iron precipitation efficiency was increased to 32.1% at 72 h when 1.33 g/L of calcium oxide was added. However, ferrous ion oxidation and total iron precipitation for jarosite and schwertmannite formation were inhibited if the amount of calcium oxide added was above 2.67 g/L, and large amounts of calcium sulfate dihydrate were generated in systems.

  17. Powder-metallurgy preparation of NiTi shape-memory alloy using mechanical alloying and spark-plasma sintering.

    Czech Academy of Sciences Publication Activity Database

    Novák, P.; Moravec, H.; Vojtěch, V.; Knaislová, A.; Školáková, A.; Kubatík, Tomáš František; Kopeček, Jaromír

    2017-01-01

    Roč. 51, č. 1 (2017), s. 141-144 ISSN 1580-2949 R&D Projects: GA ČR(CZ) GA14-03044S Institutional support: RVO:61389021 ; RVO:68378271 Keywords : mechanical alloying * spark plasma sintering * NiTi * shape memory alloy Subject RIV: JG - Metallurgy; JG - Metallurgy (FZU-D) OBOR OECD: Materials engineering ; Materials engineering (FZU-D) Impact factor: 0.436, year: 2016 https://www.researchgate.net/publication/313900224_Powder-metallurgy_preparation_of_NiTi_shape-memory_alloy_using_mechanical_alloying_and_spark-plasma_sintering

  18. Metals in Past Societies: A Global Perspective on Indigenous African Metallurgy Shadreck Chirikure

    Energy Technology Data Exchange (ETDEWEB)

    Devanathan, Ram [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

    2015-10-01

    This slim book (166 pages) shines a spotlight on pre-industrial African metallurgy, its global connections, and anthropological implications. It integrates seemingly disparate disciplines, such as history, geology, ethnography, archeology, and metallurgy, to illustrate the diversity and innovation in metallurgy across Africa and the role of metals in the rise of socio-economic inequalities and political power. The book has 7 chapters and the focus on metals as enablers of human needs and wants is evident in each chapter. The first chapter presents the context of the work and data sources. The second chapter focuses on the origin and development of mining and metallurgy in pre-industrial Africa. Chapter 3 is dedicated to the interaction of nature and culture in the process of mining. Chapter 4 deals with the transformation of the ore into metal by smelting and the sociocultural aspects of this process. Chapter 5 explores the social and cultural roles acquired by metals as a result of fabrication into objects. Chapter 6 examines the social role of metals, trade in metals, cultural contact, proto-globalization, and technology transfer. Finally, Chapter 7 draws lessons for global anthropology from the African experience. The sources of information are adequately cited and the long list of references at the end of each chapter will be a boon to researchers in this field. The author highlights the cultural aspects and social context of the adoption of metallurgy in Africa while drawing parallels between practices in pre-industrial Africa and those in other parts of the world. The book is peppered with delightful vignettes that offer insights into the process of transforming nature into culturally significant objects. For instance, African miners, like their counterparts in Nepal and Latin America, called upon deities, spirits and ancestors to mediate between nature and humans. Women had distinct roles in this process, but there were variations in these roles and in the

  19. List of unclassified documents by the staff of Metallurgy Division, AERE Harwell from January 1979 to July 1980

    International Nuclear Information System (INIS)

    Smith, N.C.

    1980-12-01

    This list constitutes unclassified material published or presented between January 1979 and July 1980, by the staff of Metallurgy Division. It covers reports, memoranda, articles in periodicals, conference papers, books and patent specifications. (author)

  20. Thermal stability and creep behaviour of MgNiYCe-rich mischmetal alloys processed by a powder metallurgy route

    Czech Academy of Sciences Publication Activity Database

    Peréz, P.; Milička, Karel; Badia, J. M.; Garcés, G.; Antoranz, J. M.; Gonzáles, S.; Dobeš, Ferdinand; Adeva, P.

    289-292, - (2009), s. 127-136 ISSN 1012-0386. [DIMAT 2008, International Conference on Diffusion in Materials /7./. Lanzarote, Canary Islands, 28.10.2008-31.10.2008] Grant - others:Ministerio de Ciencia y Tecnologia (ES) MAT2006-11731-C02 Institutional research plan: CEZ:AV0Z20410507 Keywords : magnesium alloys * powder metallurgy * microstructure * thermal stability * creep Subject RIV: JG - Metallurgy

  1. Thermogravimetric control of intermediate compounds in uranium metallurgy; Control termogravimetrico de productos intermedios de la metalurgia del uranio

    Energy Technology Data Exchange (ETDEWEB)

    Gasco Sanchez, L.; Fernandez Cellini, R.

    1959-07-01

    The thermal decomposition of some intermediate compounds in the metallurgy of the uranium as uranium peroxide, ammonium uranate, uranium and ammonium penta-fluoride, uranium tetrafluoride and uranous oxide has been study by means of the Chevenard's thermo balance. Some data on pyrolysis of synthetic mixtures of intermediate compounds which may occasionally appear during the industrial process, are given. Thermogravimetric methods of control are suggested, usable in interesting products in the uranium metallurgy. (Author) 20 refs.

  2. Annual report for the steering committee of the association Euratom-Belgian State for fusion 1998

    Energy Technology Data Exchange (ETDEWEB)

    Decreton, M

    1998-10-01

    This report is prepared for the annual steering committee meting of the Association Euratom - Belgian State in the area of fusion reactor technology. The Belgian contribution focuses on the assessment of the first wall and blanket materials under radiation and coolant interaction and on developments for the remote handling in maintenance activities. The period October 1997 to September 1998 is reported on.The fusion technology work performed at the Belgian Nuclear Research Centre SCK/CEN, the Department of Metallurgy and Materials Engineering of the Louvain University (Belgium) and S.A. Gradel, a Luxemburg-based organisation, is described.

  3. Annual report for the steering committee of the association Euratom-Belgian State for fusion 1998

    International Nuclear Information System (INIS)

    Decreton, M.

    1998-10-01

    This report is prepared for the annual steering committee meting of the Association Euratom - Belgian State in the area of fusion reactor technology. The Belgian contribution focuses on the assessment of the first wall and blanket materials under radiation and coolant interaction and on developments for the remote handling in maintenance activities. The period October 1997 to September 1998 is reported on.The fusion technology work performed at the Belgian Nuclear Research Centre SCK/CEN, the Department of Metallurgy and Materials Engineering of the Louvain University (Belgium) and S.A. Gradel, a Luxemburg-based organisation, is described

  4. Annual report for the steering committee of the association Euratom-Belgian State for fusion 1999

    International Nuclear Information System (INIS)

    Decreton, M.

    1999-10-01

    This report is prepared for the annual steering committee meting of the Association Euratom - Belgian State in the area of fusion reactor technology. The Belgian contribution focuses on the assessment of the first wall and blanket materials under radiation and coolant interaction and on developments for the remote handling in maintenance activities. The period October 1998 to September 1999 is reported on.The fusion technology work performed at the Belgian Nuclear Research Centre SCK/CEN, the Department of Metallurgy and Materials Engineering of the Louvain University (Belgium) and S.A. Gradel, a Luxemburg-based organisation, is described

  5. Annual report for the steering committee of the association Euratom-Belgian State for fusion 1999

    Energy Technology Data Exchange (ETDEWEB)

    Decreton, M

    1999-10-01

    This report is prepared for the annual steering committee meting of the Association Euratom - Belgian State in the area of fusion reactor technology. The Belgian contribution focuses on the assessment of the first wall and blanket materials under radiation and coolant interaction and on developments for the remote handling in maintenance activities. The period October 1998 to September 1999 is reported on.The fusion technology work performed at the Belgian Nuclear Research Centre SCK/CEN, the Department of Metallurgy and Materials Engineering of the Louvain University (Belgium) and S.A. Gradel, a Luxemburg-based organisation, is described.

  6. The Audit Committee. AGB Effective Committee Series

    Science.gov (United States)

    Staisloff, Richard L.

    2011-01-01

    This publication is part of an Association of Governing Boards of Universities and Colleges (AGB) series devoted to strengthening the role of key standing committees of governing boards. While there is no optimum committee system for institutions of higher education, certain principles, practices, and procedures prevail. The best practices…

  7. Possible Association of Ferrous Phosphates and Ferric Sulfates in S-rich Soil on Mars

    Science.gov (United States)

    Mao, J.; Schroeder, C.; Haderlein, S.

    2012-12-01

    NASA Mars Exploration Rover (MER) Spirit explored Gusev Crater to look for signs of ancient aqueous activity, assess past environmental conditions and suitability for life. Spirit excavated light-toned, S-rich soils at several locations. These are likely of hydrothermal, possibly fumarolic origin. At a location dubbed Paso Robles the light-toned soil was also rich in P - a signature from surrounding rock. While S is mainly bound in ferric hydrated sulfates [1], the mineralogy of P is ill-constrained [2]. P is a key element for life and its mineralogy constrains its availability. Ferrous phases observed in Paso Robles Mössbauer spectra may represent olivine and pyroxene from surrounding basaltic soil [1] or ferrous phosphate minerals [3]. Phosphate is well-known to complex and stabilize Fe 2+ against oxidation to Fe 3+ . Schröder et al. [3] proposed a formation pathway of ferrous phosphate/ferric sulfate associations: sulfuric acid reacts with basalt containing apatite, forming CaSO4 and phosphoric acid. The phosphoric and/or excess sulfuric acid reacts with olivine, forming Fe2+-phosphate and sulfate. The phosphate is less soluble and precipitates. Ferrous sulfate remains in solution and is oxidized as pH increases. To verify this pathway, we dissolved Fe2+-chloride and Na-phosphate salts in sulfuric acid inside an anoxic glovebox. The solution was titrated to pH 6 by adding NaOH when a first precipitate formed, which was ferrous phosphate according to Mössbauer spectroscopy (MB). At that point the solution was removed from the glovebox and allowed to evaporate in the presence of atmospheric oxygen, leading to the oxidation of Fe2+. The evaporation rate was controlled by keeping the suspensions at different temperatures; pH was monitored during the evaporation process. The final precipitates were analyzed by MB and X-Ray Fluorescence (XRF), comparable to MER MB and Alpha Particle X-ray Spectrometer instrument datasets, and complementary techniques such as X

  8. Ferrous arrowheads and their oil quench hardening: Some early Indian evidence

    Science.gov (United States)

    Dube, R. K.

    2008-05-01

    A wide variety of ferrous arrowheads were in use in ancient India. Several typical chemical analyses of arrowheads found from archaeological excavation carried out at Kaushambi are reported in this paper. The average carbon content of these arrowheads varied from as low as 0.1 wt.% to approximately 0.9 wt.%. Literary evidence for oil quench hardening of ferrous arrowheads, as reported in famous Sanskrit epics—the Rāmāyana and the Mahābhārata—have been discussed in this paper. This type of quench hardening was intentionally adopted as it helped in preventing distortion and formation of quench cracks in arrowheads. The oil quench-hardened arrowheads were rubbed on stones to sharpen them, which also brought about tempering of martensite due to frictional heat.

  9. New trends for non-ferrous metals in the electrical engineering industry

    International Nuclear Information System (INIS)

    Singer, R.F.

    1989-01-01

    The non-ferrous metals copper, aluminium and nickel are of major importance to the electrical engineering industry. Copper is used for magnet wire, underground cable and overhead contact wire, and aluminium is important for overhead power transmission lines. Nickel alloys are employed as gas turbine blades in power generation. An important new trend in the conductor area is rapid solidification for improved combinations of strength and conductivity. Another new trend is the Conform continuous extrusion process which can decrease cost and increase quality. New high temperature superconductors might change the conductor market completely, but only on the long run. Nickel base blading materials will see considerable improvements from oxide dispersion strengthening and directional solidification. In summary, non-ferrous materials technology for electrical engineering applications is on the move and considerable improvements can be expected within the next decade. (orig.) [de

  10. Structural and electrical properties of copper-nickel-aluminum alloys obtained by conventional powder metallurgy method

    Energy Technology Data Exchange (ETDEWEB)

    Monteiro, Waldemar A.; Carrio, Juan A.G.; Silveira, C.R. da; Pertile, H.K.S., E-mail: fisica.cch@mackenzie.br [Universidade Presbiteriana Mackenzie (UPM/CCH), Sao Paulo, SP (Brazil). Centro de Ciencias e Humanidades. Dept. de Fisica; Silva, L.C.E. da; Buso, S.J., E-mail: jgcarrio@mackenzie.br [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

    2009-07-01

    This work looked for to search out systematically, in scale of laboratory, copper-nickel-aluminum alloys (Cu-Ni-Al) with conventional powder metallurgy processing, in view of the maintenance of the electric and mechanical properties with the intention of getting electric connectors of high performance or high mechanical damping. After cold uniaxial pressing (1000 kPa), sintering (780 deg C) and convenient homogenization treatments (500 deg C for different times) under vacuum (powder metallurgy), the obtained Cu-Ni-Al alloys were characterized by optical microscopy, electrical conductivity, Vickers hardness. X rays powder diffraction data were collected for the sintered samples in order to a structural and microstructural analysis. The comparative analysis is based on the sintered density, hardness, macrostructures and microstructures of the samples. (author)

  11. Structural and electrical properties of copper-nickel-aluminum alloys obtained by conventional powder metallurgy method

    International Nuclear Information System (INIS)

    Monteiro, Waldemar A.; Carrio, Juan A.G.; Silveira, C.R. da; Pertile, H.K.S.

    2009-01-01

    This work looked for to search out systematically, in scale of laboratory, copper-nickel-aluminum alloys (Cu-Ni-Al) with conventional powder metallurgy processing, in view of the maintenance of the electric and mechanical properties with the intention of getting electric connectors of high performance or high mechanical damping. After cold uniaxial pressing (1000 kPa), sintering (780 deg C) and convenient homogenization treatments (500 deg C for different times) under vacuum (powder metallurgy), the obtained Cu-Ni-Al alloys were characterized by optical microscopy, electrical conductivity, Vickers hardness. X rays powder diffraction data were collected for the sintered samples in order to a structural and microstructural analysis. The comparative analysis is based on the sintered density, hardness, macrostructures and microstructures of the samples. (author)

  12. Development of new metal matrix composite electrodes for electrical discharge machining through powder metallurgy process

    Directory of Open Access Journals (Sweden)

    C. Mathalai Sundaram

    2014-12-01

    Full Text Available Electrical discharge machining (EDM is one of the widely used nontraditional machining methods to produce die cavities by the erosive effect of electrical discharges. This method is popular due to the fact that a relatively soft electrically conductive tool electrode can machine hard work piece. Copper electrode is normally used for machining process. Electrode wear rate is the major drawback for EDM researchers. This research focus on fabrication of metal matrix composite (MMC electrode by mixing copper powder with titanium carbide (TiC and Tungsten carbide (WC powder through powder metallurgy process, Copper powder is the major amount of mixing proportion with TiC and WC. However, this paper focus on the early stage of the project where powder metallurgy route was used to determine suitable mixing time, compaction pressure and sintering and compacting process in producing EDM electrode. The newly prepared composite electrodes in different composition are tested in EDM for OHNS steel.

  13. Quantifying the properties of low-cost powder metallurgy titanium alloys

    International Nuclear Information System (INIS)

    Bolzoni, L.; Ruiz-Navas, E.M.; Gordo, E.

    2017-01-01

    The extensive industrial employment of titanium is hindered by its high production costs where reduction of these costs can be achieved using cheap alloying elements and appropriate alternative processing techniques. In this work the feasibility of the production of low-cost titanium alloys is addressed by adding steel to pure titanium and processing the alloys by powder metallurgy. In particular, a spherical 4140 LCH steel powder commonly used in metal injection moulding is blended with irregular hydride-dehydride Ti. The new low-cost alloys are cold uniaxially pressed and sintered under high vacuum and show comparable properties to other wrought-equivalent and powder metallurgy titanium alloys. Differential thermal analysis and X-ray diffraction analyses confirm that Ti can tolerate the employment of iron as primary alloying element without forming detrimental TiFe-based intermetallic phases. Thus, the newly designed α+β alloys could be used for cheaper non-critical components.

  14. Preparation of Three-Dimensional Graphene Foams Using Powder Metallurgy Templates.

    Science.gov (United States)

    Sha, Junwei; Gao, Caitian; Lee, Seoung-Ki; Li, Yilun; Zhao, Naiqin; Tour, James M

    2016-01-26

    A simple and scalable method which combines traditional powder metallurgy and chemical vapor deposition is developed for the synthesis of mesoporous free-standing 3D graphene foams. The powder metallurgy templates for 3D graphene foams (PMT-GFs) consist of particle-like carbon shells which are connected by multilayered graphene that shows high specific surface area (1080 m(2) g(-1)), good crystallization, good electrical conductivity (13.8 S cm(-1)), and a mechanically robust structure. The PMT-GFs did not break under direct flushing with DI water, and they were able to recover after being compressed. These properties indicate promising applications of PMT-GFs for fields requiring 3D carbon frameworks such as in energy-based electrodes and mechanical dampening.

  15. [Investigation about prevention behavior for dust workers in machinery, ceramic, and metallurgy industry].

    Science.gov (United States)

    Shen, Fu-hai; Ma, Qing-kun; Xiao, Shu-yu; Cui, Feng-tao; Meng, Qing-di; Yang, Xiu-qing; Qi, Hui-sheng; Fan, Xue-yun; Yao, San-qiao

    2011-01-01

    The purposes of this thesis were to study the behavior about workers exposed to dust and provide scientific basis for health promotion. We designed a questionnaire and carry it on the 746 dust workers in the 3 representative corporations of Machinery, Ceramic, and Metallurgy Industry. All data were input into computer. And a database was established with Excel. SPSS11.5 statistical analysis software was used to analyze the influence on protecting behavioral between the application of qualifications, different jobs, training or protection, and other aspects etc. The rates were 94.4% and 75.3% about the regular physical examination and requirements for protective equipment. The rate of choosing an effective way of protection was generally low (15.4%). There was significant difference for among different educational background workers (P Metallurgy Industry. Those who were not educated had a lower using rate about the protection behavior, regular physical examination, and requirements for protective equipment than those educated.

  16. [Risk and features of occupational diseases in nonferrous metallurgy workers of Kolsky Transpolar area].

    Science.gov (United States)

    Siurin, S A; Chashchin, V P; Frolova, N M

    2015-01-01

    The study covered data on 977 cases of occupational diseases in 615 workers of nonferrous metallurgy in Kolsky Transpolar area. Findings are high risk of occupational diseases in workers engaged into electrolysis production of aluminium, all nickel reprocessing and pyrometallic copper reprocessing (GR 7.02-10.0). Electrolysis operators and anode operators of aluminium production are more prone to occupational diseases, with bone and muscular disorders (46.8%) prevalent in the morbidity structure. Respiratory diseases are more prevalent (68.2-100%) in the occupational morbidity structure of copper-nickelindustry workers. Conclusion is made on mandatory improvement of the work conditions and more effective individual protective means against occupational hazards in workers of nonferrous metallurgy in Kolsky Transpolar area.

  17. Estimation and characterization of polycyclic aromatic hydrocarbons from magnesium metallurgy facilities in China.

    Science.gov (United States)

    Nie, Zhiqiang; Yang, Yufei; Tang, Zhenwu; Liu, Feng; Wang, Qi; Huang, Qifei

    2014-11-01

    Field monitoring was conducted to develop a polycyclic aromatic hydrocarbon (PAH) emission inventory for the magnesium (Mg) metallurgy industry in China. PAH emissions in stack gas and fly/bottom ash samples from different smelting units of a typical Mg smelter were measured and compared. Large variations of concentrations, congener patterns, and emission factors of PAHs during the oxidation and reduction stages in the Mg smelter were observed. The measured average emission factor (166,487 μg/t Mg) was significantly higher than those of other industrial sources. Annual emission from Mg metallurgy in 2012 in China was estimated at 116 kg (514 g BaPeq) for PAHs. The results of this study suggest that PAH emission from Mg industries should be considered by local government agencies. These data may be helpful for understanding PAH levels produced by the Mg industry and in developing a PAH inventory.

  18. Mechanical properties of metals for biomedical applications using powder metallurgy process: A review

    Science.gov (United States)

    Dewidar, Montasser Marasy; Yoon, Ho-Chel; Lim, Jae Kyoo

    2006-06-01

    The uses of biomaterials have been revolutionizing the biomedical field in deployment as implants for humans. During the past five decades, many implant materials made of metals have been put into practical use. Powder metallurgy techniques have been used to produce controlled porous structures, such as porous coatings applied for dental and orthopedic surgical implants, which allow bony tissue ingrowth within the implant surface, thereby improving fixation. This paper examines various important metals using powder metallurgy technology to produce elements of a total hip replacement. These alloys are 316L stainless steel alloy, Co-Cr-Mo alloy, and Ti-6Al-4V alloy. Also, this paper examines current information on the mechanical properties. Mechanical properties are discussed as a function of type of materials and process of fabrication. This article addresses the engineering aspects concerning the advantages and disadvantages of each type of material.

  19. Conflitos ambientais: uma análise da assimetria de poder entre os atores sociais envolvidos no caso do Mineroduto da Ferrous / Environmental conflict: an analysis of power asymmetry between social actors involved in the case of Ferrous Pipeline

    Directory of Open Access Journals (Sweden)

    Dayane Rouse Neves Sousa

    2015-12-01

    Full Text Available This work intends to present the environmental conflict initiated due to the installation of pipeline Ferrous Ressources S / A, in the micro region of Viçosa-MG, building an analysis of the positioning of the main social actors involved, as well as their respective relations of power. Thepipeline of Ferrous will connect the complex Beam Mine in Congonhas-MG, the port of Ferrous Ressources in Presidente Kennedy-ES in order to export iron ore. To do so, were used as methodological procedures: bibliographical research; document analysis; semi-structured interviews with different actors; and follow-up meetings of the Popular Campaign Against the Water and Pipeline Ferrous, public hearings and demonstrations taken place in the Viçosa. Furthermore, there was monitoring of the pipeline discussion in local newspapers and on blogs. Thus, this study demonstrated that the Ferrous company, which owns high economic and symbolic power, assumes the role of dominating the conflict. On the other hand, those affected and social movements against the construction of the project, are sometimes in the role of dominated, leaving them to articulate strategies of resistance to delay / stop the construction of the pipeline. The state, in turn, assumes different roles in this context, demonstrating thereby weakness in mediation and conflict management established by pipeline Ferrous mainly in the micro region of Viçosa-MG.

  20. Separation of non-ferrous metals from ASR by corona electrostatic separation

    Science.gov (United States)

    Kim, Yang-soo; Choi, Jin-Young; Jeon, Ho-Seok; Han, Oh-Hyung; Park, Chul-Hyun

    2016-04-01

    Automotive shredder residue (ASR), the residual fraction of approximate 25% obtained after dismantling and shredding from waste car, consists of polymers (plastics and rubber), metals (ferrous and non-ferrous), wood, glass and fluff (textile and fiber). ASR cannot be effectively separated due to its heterogeneous materials and coated or laminated complexes and then largely deposited in land-fill sites as waste. Thus reducing a pollutant release before disposal, techniques that can improve the liberation of coated (or laminated) complexes and the recovery of valuable metals from the shredder residue are needed. ASR may be separated by a series of physical processing operations such as comminution, air, magnetic and electrostatic separations. The work deals with the characterization of the shredder residue coming from an industrial plant in korea and focuses on estimating the optimal conditions of corona electrostatic separation for improving the separation efficiency of valuable non-ferrous metals such as aluminum, copper and etc. From the results of test, the maximum separation achievable for non-ferrous metals using a corona electrostatic separation has been shown to be recovery of 92.5% at a grade of 75.8%. The recommended values of the process variables, particle size, electrode potential, drum speed, splitter position and relative humidity are -6mm, 50 kV, 35rpm, 20° and less 40%, respectively. Acknowledgments This study was supported by the R&D Center for Valuable Recycling (Global-Top R&BD Program) of the Ministry of Environment. (Project No. GT-11-C-01-170-0)

  1. Determination of reliability of express forecasting evaluation of radiometric enriching ability of non-ferrous ores

    International Nuclear Information System (INIS)

    Kirpishchikov, S.P.

    1991-01-01

    Use of the data of nuclear physical methods of sampling and logging enables to improve reliability of evaluation of radiometric enriching ability of ores, as well as to evaluate quantitatively this reliability. This problem may be solved by using some concepts of geostatistics. The presented results enable to conclude, that the data of nuclear-physical methods of sampling and logging can provide high reliability of evaluation of radiometric enriching ability of non-ferrous ores and their geometrization by technological types

  2. Studying phase structure of burned ferrous manganese ores by method of nuclear gamma-resonance spectroscopy

    OpenAIRE

    Shayakhmetov, B.; Issagulov, A.; Baisanov, A.; Karakeyeva, G.; Issagulovа, D.

    2014-01-01

    In the given article there are presented the results of studying the phase structure of burned ferrous manganese ores of Zhomart and Zapadny Kamys deposits of by the method of Mossbauer spectroscopy. There is established a variety of iron location forms in the studied materials and their quantitative content that allows to define the degree of completing regenerative processes at magnetizing roasting, and also the processes of formation of solid solutions (Fe1-XMX3O4 and stabilization of Fe1-...

  3. Stress corrosion cracking of several high strength ferrous and nickel alloys

    Science.gov (United States)

    Nelson, E. E.

    1971-01-01

    The stress corrosion cracking resistance of several high strength ferrous and nickel base alloys has been determined in a sodium chloride solution. Results indicate that under these test conditions Multiphase MP35N, Unitemp L605, Inconel 718, Carpenter 20Cb and 20Cb-3 are highly resistant to stress corrosion cracking. AISI 410 and 431 stainless steels, 18 Ni maraging steel (250 grade) and AISI 4130 steel are susceptible to stress corrosion cracking under some conditions.

  4. Degradation of toluene, ethylbenzene, and xylene using heat and chelated-ferrous iron activated persulfate oxidation

    Science.gov (United States)

    Mondal, P.; Sleep, B.

    2014-12-01

    Toluene, ethylbenze, and xylene (TEX) are common contaminants in the subsurface. Activated persulfate has shown promise for degrading a wide variety of organic compounds. However, studies of persulfate application for in situ degradation of TEX and effects on the subsequent bioremediation are limited. In this work, degradation studies of TEX in aqueous media and soil are being conducted using heat activated and chelated-ferrous iron activated persulfate oxidation in batch and flow-through column experiments. In the batch experiments, sodium persulfate is being used at different concentrations to provide an initial persulfate to TEX molar ratios between 10:1 and 100:1. Sodium persulfate solutions are being activated at 20, 37, 60, and 80 oC temperatures for the heat activated oxidation. For the chelated-ferrous iron activated oxidation, ferrous iron and citric acid, both are being used at concentration of 5 mM. In the experiments with soil slurry, a soil to water ratio of 1 to 5 is being used. Flow through water saturated column experiments are being conducted with glass columns (45 cm in length and 4 cm in diameter) uniformly packed with soils, and equilibrated with water containing TEX at the target concentrations. Both the heat activation and chelated-ferrous iron activation of persulfate are being employed in the column experiments. Future experiments are planned to determine the suitability of persulfate oxidation of TEX on the subsequent biodegradation using batch microcosms containing TEX degrading microbial cultures. In these experiments, the microbial biomass will be monitored using total phospholipids, and the microbial community will be determined using quantitative real-time polymerase chain reaction (qPCR) on the extracted DNA. This study is expected to provide suitable operating conditions for in situ chemical oxidation of TEX with activated persulfate followed by bioremediation.

  5. Synthesis and characterization of a ferrous compound material obtained by combustion of ferroboron and ferrotitanium mixtures

    International Nuclear Information System (INIS)

    Bejar, M.A; Fuenzalida, J.L

    2008-01-01

    A ferrous compound material was synthesized in this work, by the air auto-combustion of mixtures of powdered ferroboron and ferrotitanium, compacted under pressures of 79 and 93 MPa and preheated to a temperature of about 1000 o C. The synthesized compounds were characterized by XRD analysis, and macro and micro-hardness tests. The formation of titanium diboride was found in all the synthesized test pieces (au)

  6. Synthesis and characterization of ferrous phosphate (vivianite) and its behavior in aqueous media

    International Nuclear Information System (INIS)

    Diaz F, J.C.

    2003-01-01

    The synthesis and characterization of materials that can be useful in Environmental Chemistry is very important because their characteristics are exposed and its behavior in chemical phenomena as the sorption in aqueous media is understand to use it in the human being benefit. With the object of using, in a future, the octa hydrated ferrous phosphate (vivianite) as a potential candidate for matrix confinement in contention walls for the storage of radioactive waste of long half life, it was synthesized and it characterized physico chemically and their properties of surface of this compound were evaluated. Presently work was carried out the synthesis and structural characterization of the iron phosphate II by infrared spectroscopy with having Fourier transform, high vacuum scanning electron microscopy, X-ray diffraction, thermal gravimetric analysis, the BET multipoint surface area and Moessbauer spectroscopy; as well as, the determination between aqueous media of the isoelectric point and the density of sites of surface of the compound. The octa hydrated ferrous phosphate was obtained pure. The results indicate that the product corresponds to the prospective mineral, the vivianite. The thermal gravimetric analysis demonstrated that the ferrous phosphate is a stable salt after the lost of water. The isoelectric point is since an important parameter because allows to know the behavior of the surface of the material in aqueous systems, in this case the isoelectric point, of the octa hydrated ferrous phosphate, in distilled water is of pH 4.20 and in solution of potassium nitrate 0.5 M is of pH = 3.75. This indicates that the material has an amphoteric surface depending on the pH. On the other hand, the density of active sites of surface obtained by titrations acid-base is of 20 sites by nm 2 . (Author)

  7. Metallurgy Department. Progress Report for the Period 1 January to 31 December 1984

    DEFF Research Database (Denmark)

    Risø National Laboratory, Roskilde

    The activities of the Metallurgy Department at Risø during 1984 are described. The work is presented in three chapters: General Materials Research, Technology and Materials Development, and Fuel Elements. A survey is given of the Department's participation in international collaboration and of its...... activities within education and training. A list (with abstracts) of publications and lectures by the staff during 1984 is included....

  8. Metallurgy Department progress report for the period 1 January to 31 December 1986

    International Nuclear Information System (INIS)

    Schroeder Pedersen, A.; Bilde-Soerensen, J.B.

    1987-04-01

    The activities of the Metallurgy Department at Risoe during 1986 are described. The work is presented in four chapters: General Materials Research, Technology and Materials Development, Chemical and Electrochemical Energy Research and Development, and Fuel Elements. A survey is given of the Department's participation in international collaboration and of its activities within education and training. A list (with abstracts) of publications and lectures by the staff during 1986 is included. (editors)

  9. Characterization of Powder Metallurgy Processed Pure Magnesium Materials for Biomedical Applications

    Czech Academy of Sciences Publication Activity Database

    Březina, M.; Minda, J.; Doležal, P.; Krystýnová, M.; Fintová, Stanislava; Zapletal, J.; Wasserbauer, J.; Ptáček, P.

    2017-01-01

    Roč. 7, č. 11 (2017), č. článku 461. ISSN 2075-4701 Institutional support: RVO:68081723 Keywords : magnesium * powder metallurgy * cold pressing * hot pressing * EIS (Electrochemical impedance spectroscopy) * three-point bending test * corrosion Subject RIV: JK - Corrosion ; Surface Treatment of Materials OBOR OECD: Coating and films Impact factor: 1.984, year: 2016 http://www.mdpi.com/2075-4701/7/11/461

  10. Metallurgy department progress report for the period 1 January to 31 December 1977

    International Nuclear Information System (INIS)

    1978-03-01

    The activities of the Metallurgy Department at Risoe during 1977 are described. The work is presented in four chapters: General Materials Research, Technology and Materials Development, Fuel elements, and Non-Destructive Testing. Furthermore, a survey is given of the department's participation in international collaboration and of its activities within education and training. A list (with abstracts) of publications and lectures by the staff during 1977 is included. (author)

  11. Metallurgy Department progress report for the period 1 January to 31 December 1985

    International Nuclear Information System (INIS)

    Schroeder Pedersen, A.; Bilde Soerensen, J.B.

    1986-04-01

    The activities of the Metallurgy department at Risoe during 1985 are described. The work is presented in four chapters: General Materials Research, Technology and Materials Development, Chemical and Electrochemical Energy Research and Development, and Fuel elements. A survey is given of the Department's participation in international collaboration and of its activities within education and training. A list (with abstracts) of publications and lectures by the staff during 1985 is included. (author)

  12. Production of titanium alloys for advanced aerospace systems by powder metallurgy

    OpenAIRE

    Henriques, Vinicius André Rodrigues; Campos, Pedro Paulo de; Cairo, Carlos Alberto Alves; Bressiani, José Carlos

    2005-01-01

    Titanium alloys parts are ideally suited for advanced aerospace systems because of their unique combination of high specific strength at both room temperature and moderately elevated temperature, in addition to excellent corrosion resistance. Despite these features, use of titanium alloys in engines and airframes is limited by cost. The alloys processing by powder metallurgy eases the obtainment of parts with complex geometry. In this work, results of the Ti-6Al-4V and Ti-13Nb-13Zr alloys pro...

  13. A Comparison of the Plastic Flow Response of a Powder Metallurgy Nickel Base Superalloy (Postprint)

    Science.gov (United States)

    2017-04-01

    Materials The nickel-base, powder-metallurgy (PM) cc¢ super- alloy LSHR was used to establish the effect of test method on plastic -flow response under hot...of friction was estimated to lead to maximum errors in flow stress of the order of 3 pct for the sample geometry and height reduction used in the... plastic -flow behavior of LSHR (in effective stress-strain terms) was described using a phenomeno- logical relationship typical of those for

  14. Metallurgy department progress report for the period 1 January to 31 December 1980

    International Nuclear Information System (INIS)

    1981-07-01

    The activities of the Metallurgy Department at Risoe during 1980 are described. The work is presented in four chapters: General Materials Research, Technology and Materials Development, Fuel Elements, Non-Destructive Testing. Furthermore, a survey is given of the department's participation in international collaboration and of its activities within education and training. A list (with abstracts) of publications and lectures by the staff during 1980 is included. (Author)

  15. Review of some past and present powder metallurgy programs at the Los Alamos Scientific Laboratory

    International Nuclear Information System (INIS)

    Sheinberg, H.

    1977-01-01

    Powder metallurgy programs at LASL are reviewed. Topics covered include: KIWI reactor fuel elements; Phoebus reactor fuel elements, criticality control and poison plate material, structural composites for fuel element supports, and heat shields for fuel element supports; thermionic emitter reactor uranium carbide--zirconium carbide fuel pins, and molybdenum--uranium oxide fuel pins; laser and electron beam fusion targets; and current work in MHD components

  16. Situation of radioactive wastes and their prevention and treatment measures in China's uranium mining and metallurgy

    International Nuclear Information System (INIS)

    Li Renjie.

    1988-01-01

    The sorts of radioactive wastes produced in uranium mining and metallurgy and their hazards are discribed in this paper. The characteristics of the radioactive wastes are discussed. The measurements and results are introduced for treatment and disposal of the radioactive wastes. The way to deal with prevention and treatment of radioactive wastes is presented in the stages of engineering design, construction, production and decommission of uranium mines and plants

  17. Extractive metallurgy of the beryllium; Fundamentos da metalurgia extrativa do berilio

    Energy Technology Data Exchange (ETDEWEB)

    Alonso, Neusa; Capocchi, Jose Deodoro Trani [Sao Paulo Univ., SP (Brazil). Escola Politecnica

    1995-07-01

    A bibliographic review is performed on the beryllium extractive metallurgy. The work describes the main type of ores and processes applied to the metallic beryllium production, beryllium oxide production using fluoride, sulfide and direct chlorination. The thermodynamic consideration are made on beryllium reduction processes, discussing the viability of the beryllium oxide and hallide reduction processes. Under the technological viewpoint, the Cu-Be alloys main production processes are discussed, and the main toxicity problems related with beryllium are mentioned 15 refs..

  18. Metallurgy department progress report for the period 1 January to 31 December 1978

    International Nuclear Information System (INIS)

    1979-04-01

    The activities of the metallurgy department at Risoe during 1978 are described. The work is presented in four chapters: General materials research, technology and materials development, fuel elements, and non-destructive testing. Furthermore, a survey is given of the depratment's participation in international collaboration and of its activities within education and training. A list (with abstracts) of publications and lectures by the staff during 1978 is included. (author)

  19. Investigation of a thermoplastic-powder metallurgy process for the fabrication of porous niobium rods

    International Nuclear Information System (INIS)

    Nordin, D.R.

    1978-06-01

    The feasibility of using a thermoplastic-powder metallurgy technique for the fabrication of porous niobium rods was investigated. Some early problems were overcome to successfully extrude the polymer coated niobium powder into long lengths. The effects of certain process variables were investigated. Residual porosity and extrusion pressure were found to be regulated by the polymer fraction. The procedures for taking the extruded polystyrene--niobium rods through the heat treatments to the final, tin infiltrated stage are explained

  20. Metallurgy department progress report for the period 1 January to 31 December 1983

    International Nuclear Information System (INIS)

    1984-06-01

    The activities of the Metallurgy Department at Risoe during 1983 are described. The work is presented in three chapters: General Materials Research, Technology and Materials Development, and Fuel Elements. Furthermore, a survey is given of the Department's participation in international collaboration and of its activities within education and training. A list (with abstracts) of publications and lectures by the staff during 1983 is included. (author)

  1. COMPARATIVE STUDY OF EFFICACY OF FERROUS SULPHATE AND CARBONYL IRON IN ANEMIA OF ANTENATAL WOMEN

    Directory of Open Access Journals (Sweden)

    Radhika

    2015-03-01

    Full Text Available Iron deficiency anemia is the most common and important public health problem all over the world in the risk group of antenatal women. Research is going on to improve the iron status of the pregnant women with different forms of iron available. In this regard, Carbonyl Iron is showing promising results in improving the red cell mass with better compliance. 120 antenatal women were recruited in this study. The study comprised of 6weeks for each patient. They were given Carbonyl Iron 100 mg/day and FeS04 100gm/day . Before and after treatment all the baseline and specific investigations were one. Results were tabulated, comparison and significance were tested by unpaired student ’s’ test and their 'p' value was calculated. Results were shown graphically also. Carbonyl Iron showed improvement in hemoglobin, PCV and better than ferrous Sulphate (P <0.001. Incidence of side effects were less with Carbonyl Iron than Ferrous Sulphate, better compliance was seen with Carbonyl Iron. In conclusion, the present study s howed that Carbonyl Iron had better efficacy and safety in the management of Iron deficiency anemia in antenatal women than ferrous Sulphate

  2. Sorption of ferrous iron by EPS from the acidophilic bacterium Acidiphilium Sp.: A mechanism proposal

    International Nuclear Information System (INIS)

    Tapia, J.M.; MuNoz, J.; Gonzlez, F.; Blazquez, M.L.; Ballester, A.

    2016-01-01

    The aim of this work was to assess the uptake of Fe(II) by extracellular polymeric substances (EPS) from the acidophilic bacterium Acidiphillium 3.2Sup(5). These EPS were extracted using EDTA. EPS of A. 3.2Sup(5) loaded in sorption tests with Fe(II), were characterized using the following experimental techniques: scanning electron microscopy (SEM) with energy dispersive X-ray microanalysis (EDX), X-ray diffraction (XRD) and Fourier transform infrared spectroscopy (FTIR). The experimental results indicate that EPS adsorb ferrous iron according to Freundlich model with a metal sorption uptake of K = 1.14 mg1−1/n L1/n g−1 and a sorption intensity of 1/n = 1.26. In addition, ferrous iron sorption by EPS took place by preferential interaction with the carboxyl group which promotes the formation of ferrous iron oxalates (FeC2O4). Since the interaction reaction was reversible (Log K = 0.77 ± 0.33), that means that the cation sorption can be reversed at convenience. (Author)

  3. Sorption of ferrous iron by EPS from the acidophilic bacterium Acidiphilium Sp.: A mechanism proposal

    Energy Technology Data Exchange (ETDEWEB)

    Tapia, J.M.; MuNoz, J.; Gonzlez, F.; Blazquez, M.L.; Ballester, A.

    2016-07-01

    The aim of this work was to assess the uptake of Fe(II) by extracellular polymeric substances (EPS) from the acidophilic bacterium Acidiphillium 3.2Sup(5). These EPS were extracted using EDTA. EPS of A. 3.2Sup(5) loaded in sorption tests with Fe(II), were characterized using the following experimental techniques: scanning electron microscopy (SEM) with energy dispersive X-ray microanalysis (EDX), X-ray diffraction (XRD) and Fourier transform infrared spectroscopy (FTIR). The experimental results indicate that EPS adsorb ferrous iron according to Freundlich model with a metal sorption uptake of K = 1.14 mg1−1/n L1/n g−1 and a sorption intensity of 1/n = 1.26. In addition, ferrous iron sorption by EPS took place by preferential interaction with the carboxyl group which promotes the formation of ferrous iron oxalates (FeC2O4). Since the interaction reaction was reversible (Log K = 0.77 ± 0.33), that means that the cation sorption can be reversed at convenience. (Author)

  4. The effect of adding ferrous sulfate to methylphenidate on attention-deficit/hyperactivity disorder in children

    Directory of Open Access Journals (Sweden)

    Gholamreza Panahandeh

    2017-01-01

    Full Text Available Attention deficit/hyperactivity disorder (ADHD is one of the most common psychiatric disorders in children with several complications. This study was conducted to investigate the effect of adding ferrous sulfate to methylphenidate in decreasing ADHD symptoms. This study was a double-blind, randomized clinical trial. In this study, 42 nonanemic children with ADHD and serum ferritin below 30 mg/ml were enrolled according to convenience sampling and randomly assigned to two groups of 21 each, cases and controls. The two groups were matched for age and sex. The case group was administered with ferrous sulfate 5 mg/kg in addition to methylphenidate up to 1 mg/kg and the control group with methylphenidate alone. The scores on child symptoms inventory-4 (CSI-4 were recorded at baseline and after 2 months of treatment. Data were analyzed by t-test, Pearson's correlation coefficient, and repeated measures ANOVA in SPSS 16. The scores on CSI-4 decreased significantly at month 2 in both groups (P < 0.001. The scores on attention deficit and hyperactivity subscales of the CSI-4 were significantly lower in the case group than the control group (P < 0.05. The total score on CSI-4 decreased more markedly in the case group (P < 0.04. Use of ferrous sulfate plus methylphenidate can be effective in reducing ADHD symptoms in nonanemic children with low serum ferritin.

  5. Oral iron therapy in human subjects, comparative absorption between ferrous salts and iron polymaltose

    International Nuclear Information System (INIS)

    Jacobs, P.; Johnson, G.; Wood, L.

    1984-01-01

    Iron absorption was directly compared between equivalent doses of ferrous salts and a polymaltose complex using a twin-isotope technique in which each individual acts as his own control. In the first study, bioavailability of iron from ferrous sulfate and the complex was defined at physiologic doses of 5 mg (Group 1: n = 14) and therapeutic doses of 50 mg (Group 2: n = 13). In Group 1, mean absorption from salt was 47.77% (SD 14.58%) and from polymaltose, 46.56% SD 17.07%). In Group 2, mean absorption from salt was 32.92% (SD 13.42%) and from polymaltose, 27.07% (SD 6.50%). In a second study, 100 mg of iron in a chewable formulation was used to compare absorption between equal doses of ferrous fumarate and the polymaltose complex. Mean absorption from salt was 10.25% (SD 6.89%) and from polymaltose 10.68% (SD 4.68%). At all three dosage levels, iron is equally available from salt or polymaltose for hemoglobin synthesis (p greater than 0.20), and absorption negatively correlated with plasma ferritin (p less than 0.01). These two materials may be used interchangeably in the treatment of patients with absolute iron deficiency

  6. Advisory Committee Handbook.

    Science.gov (United States)

    Black Hawk Coll., Moline, IL.

    An advisory committee is generally comprised of persons outside the education profession who have specialized knowledge in a given area. The committee advises, makes recommendations, and gives service to the college and its students, instructors, and administrators. At Black Hawk College, there are four types of advisory committees: community,…

  7. Effect of repressing on the mechanical properties of the valve guides manufactured by powder metallurgy

    Directory of Open Access Journals (Sweden)

    Andrés Rodríguez-Spitia

    2017-03-01

    Full Text Available Characterization of hardness, mass loss, and friction coefficient, was carried out on valve guides for internal combustion engines, manufactured by powder metallurgy, with the aim of finding out if they fulfill the requirements of an internal combustion engine and to be mass produced. Currently available brass casting valve guides were used as comparative parameter. It was analyzed whether properties were present in a homogeneous way in the piece lengthwise; the additional repressing process carried out in the production line with respect to the sintered guides was evaluated. Therefore, Brinell, Vickers and dry slip pin-on-disk tests were done in order to determine the friction coefficient and the wear rate. Scanning electron microscopy SEM and the metallographic analysis were used to study the wear mechanism, chemical composition of the guides, and the effect of repressing -quantifying the porosity. It was clear that these pieces manufactured by powder metallurgy process showed lower values in their mechanical-tribological properties compared to commercially available valve guides taken as reference. With these results, the company which manufactures the guides by powder metallurgy will make some adjustments suggested for the parameters at the guide’s production line.

  8. Manufacture of good-weldable low oxygen molybdenum by powder metallurgy

    International Nuclear Information System (INIS)

    Hiraoka, Yutaka; Okada, Masatoshi; Akiyama, Takashi; Yamafuchi, Yasuo.

    1984-01-01

    In general most of commercial molybdenum is produced by the powder metallurgy method and is utilized as a superior heat-resisting material in many fields. Moreover, molybdenum is expected to be used as the first-wall components of JT-60 (JAERI Tokamak-60). However, one of major problems on molybdenum, particularly on powder metallurgy molybdenum, is that any sound welded joint is hard to be obtainable. In many cases weld pores are formed on welding and, therefore, ductility of the welded joint is severely degraded. The object of the present work is to get a sound welded joint without any weld pores by reducing impurity levels in the material. The materials were produced by modifying one or several parts in the ordinary manufacturing process of powder metallurgy molybdenum. Oxygen, nitrogen, carbon and other principal metallic impurities were chemically analysed. The above materials were then subjected to electron-beam-welding by using a melt-run technique, and the soundness of the welded joints was examined by optical microscopy. (author)

  9. Properties of WZ21 (%wt) alloy processed by a powder metallurgy route.

    Science.gov (United States)

    Cabeza, Sandra; Garcés, Gerardo; Pérez, Pablo; Adeva, Paloma

    2015-06-01

    Microstructure, mechanical properties and corrosion behaviour of WZ21 (%wt) alloy prepared by a powder metallurgy route from rapidly solidified powders have been studied. Results were compared to those of the same alloy prepared through a conventional route of casting and extrusion. The microstructure of the extruded ingot consisted of α-Mg grains and Mg3Zn3Y2 (W-phase) and LPSO-phase particles located at grain boundaries. Moreover, stacking faults were also observed within α-Mg grains. The alloy processed by the powder metallurgy route exhibited a more homogeneous and finer microstructure, with a grain size of 2 μm. In this case W-phase and Mg24Y5 phase were identified, but not the LPSO-phase. The microstructural refinement induced by the use of rapidly solidified powders strengthened the alloy at room temperature and promoted superplasticity at higher strain rates. Corrosion behaviour in PBS medium evidenced certain physical barrier effect of the almost continuous arrangements of second phases aligned along the extrusion direction in conventionally processed WZ21 alloy, with a stable tendency around 7 mm/year. On the other hand, powder metallurgy processing promoted significant pitting corrosion, inducing accelerated corrosion rate during prolonged immersion times. Copyright © 2015 Elsevier Ltd. All rights reserved.

  10. A millennium of metallurgy recorded by lake sediments from Morococha, Peruvian Andes.

    Science.gov (United States)

    Cooke, Colin A; Abbott, Mark B; Wolfe, Alexander P; Kittleson, John L

    2007-05-15

    To date, information concerning pre-Colonial metallurgy in South America has largely been limited to the archaeological record of artifacts. Here, we reconstruct a millennium of smelting activity in the Peruvian Andes using the lake-sediment stratigraphy of atmospherically derived metals (Pb, Zn, Cu, Ag, Sb, Bi, and Ti) and lead isotopic ratios (206Pb/ 207Pb) associated with smelting from the Morococha mining region in the central Peruvian Andes. The earliest evidence for metallurgy occurs ca. 1000 A.D., coinciding with the fall of the Wari Empire and decentralization of local populations. Smelting during this interval appears to have been aimed at copper and copper alloys, because of large increases in Zn and Cu relative to Pb. A subsequent switch to silver metallurgy under Inca control (ca. 1450 to conquest, 1533 A.D.) is indicated by increases in Pb, Sb, and Bi, a conclusion supported by further increases of these metals during Colonial mining, which targeted silver extraction. Rapid development of the central Andes during the 20th century raised metal burdens by an order of magnitude above previous levels. Our results represent the first evidence for pre-Colonial smelting in the central Peruvian Andes, and corroborate the sensitivity of lake sediments to pre-Colonial metallurgical activity suggested by earlier findings from Bolivia.

  11. Experimental Investigation and Simulation of Ferrous Biooxidation and Flow Hydrodynamics in a Bubble Column Bioreactor Using CFD Approach

    Science.gov (United States)

    Mousavi, S. M.; Jafari, A.; Yaghmaei, S.; Vossoughi, M.; Turunen, I.

    2008-05-01

    In the present attempt a set of experiments and a 3D simulation using a commercially available computational fluid dynamics package (FLUENT) were adopted to investigate complex behavior involving hydrodynamics and ferrous biological oxidation in a gas-liquid bubble column reactor. By combining the hydrodynamics and chemical species transport equations, the velocity field, air volume fraction and ferrous biooxidation rate in the column were simulated. The kinetic model proposed by Nemati and Webb (1998) was used to simulate the biooxidation rate in the column. Gas-liquid interactions were modeled using an Eulerian model in three dimensions. The effects of inlet air velocity and initial substrate (Fe+2) concentration on the velocity field, air volume fraction and biooxidation rate of ferrous iron in the column were investigated. To validate the model, simulation was compared with the experimental data in the presence of Acidithiobacillus ferrooxidans in an aerated column where the superficial gas velocity was adjusted between 0 and 0.5 m/s. It was found that the initial ferrous concentration and the inlet air velocity had a pronounced effect on the ferrous biooxidation rate. The results indicated that the maximum biooxidation rate can be obtained at superficial air velocity of 0.1 m/s and initial ferrous concentration of 6.7 g/L.

  12. 75 FR 60430 - Federal Advisory Committee; Threat Reduction Advisory Committee

    Science.gov (United States)

    2010-09-30

    ... of the Secretary Federal Advisory Committee; Threat Reduction Advisory Committee AGENCY: Office of... meeting. SUMMARY: Under the provisions of the Federal Advisory Committee Act of 1972 (5 U.S.C., Appendix... announces a meeting of the Threat Reduction Advisory Committee (hereafter referred to as ``the Committee...

  13. Protonation of Ferrous Dinitrogen Complexes Containing a Diphosphine Ligand with a Pendant Amine

    Energy Technology Data Exchange (ETDEWEB)

    Heiden, Zachariah M.; Chen, Shentan; Mock, Michael T.; Dougherty, William G.; Kassel, W. S.; Rousseau, Roger J.; Bullock, R. Morris

    2013-04-01

    The addition of protons to pendant amine containing ferrous dinitrogen complexes, of the type [FeX(N2)(PEtNMePEt)(dmpm)]+ (X = H, Cl, or Br; PEtNMePEt = Et2PCH2N(Me)CH2PEt2 and dmpm = Me2PCH2PMe2), was found to protonate at the pendant amine as opposed to the dinitrogen ligand. This protonation increased the νN2 of the complex by about 25 cm-1, shifting the Fe(II/I) couple 330 mV to a more positive potential. A similar shift was observed in the case of [FeX(CO)(PEtNMePEt)(dmpm)]+ (X = H, Cl, or Br). Computational analysis verified these experimental results and showed the coordination of N2 to Fe(II) centers increases the basicity of N2 (vs. free N2) by 13 and 20 pKa units for the trans halides and hydrides, respectively. Although the iron center was found to increase the basicity of the bound N2 ligand, coordinated N2 is not sufficiently basic to be protonated. In the case of ferrous dinitrogen complexes containing a basic pendant methylamine, the amine site was determined to be the most basic site by 30 pKa units compared to protonation at the N2 ligand. To increase the basicity of the N2 ligand in order to promote proton transfer from the pendant amine to the N2 ligand, chemical reduction of these ferrous dinitrogen complexes was performed and found to result in oxidative addition of the methylene C-H bond of the PEtNMePEt ligand to Fe, preventing isolation of a reduced Fe(0) N2 complex. This work was supported as part of the Center for Molecular Electrocatalysis, an Energy Frontier Research Center funded by the U.S. Department of Energy Office of Science, Office of Basic Energy Sciences.

  14. Elucidating the role of ferrous ion cocatalyst in enhancing dilute acid pretreatment of lignocellulosic biomass

    Directory of Open Access Journals (Sweden)

    Wei Hui

    2011-11-01

    Full Text Available Abstract Background Recently developed iron cocatalyst enhancement of dilute acid pretreatment of biomass is a promising approach for enhancing sugar release from recalcitrant lignocellulosic biomass. However, very little is known about the underlying mechanisms of this enhancement. In the current study, our aim was to identify several essential factors that contribute to ferrous ion-enhanced efficiency during dilute acid pretreatment of biomass and to initiate the investigation of the mechanisms that result in this enhancement. Results During dilute acid and ferrous ion cocatalyst pretreatments, we observed concomitant increases in solubilized sugars in the hydrolysate and reducing sugars in the (insoluble biomass residues. We also observed enhancements in sugar release during subsequent enzymatic saccharification of iron cocatalyst-pretreated biomass. Fourier transform Raman spectroscopy showed that major peaks representing the C-O-C and C-H bonds in cellulose are significantly attenuated by iron cocatalyst pretreatment. Imaging using Prussian blue staining indicated that Fe2+ ions associate with both cellulose/xylan and lignin in untreated as well as dilute acid/Fe2+ ion-pretreated corn stover samples. Analyses by scanning electron microscopy and transmission electron microscopy revealed structural details of biomass after dilute acid/Fe2+ ion pretreatment, in which delamination and fibrillation of the cell wall were observed. Conclusions By using this multimodal approach, we have revealed that (1 acid-ferrous ion-assisted pretreatment increases solubilization and enzymatic digestion of both cellulose and xylan to monomers and (2 this pretreatment likely targets multiple chemistries in plant cell wall polymer networks, including those represented by the C-O-C and C-H bonds in cellulose.

  15. Studying phase structure of burned ferrous manganese ores by method of nuclear gamma-resonance spectroscopy

    Directory of Open Access Journals (Sweden)

    B. Shayakhmetov

    2014-04-01

    Full Text Available In the given article there are presented the results of studying the phase structure of burned ferrous manganese ores of Zhomart and Zapadny Kamys deposits of by the method of Mossbauer spectroscopy. There is established a variety of iron location forms in the studied materials and their quantitative content that allows to define the degree of completing regenerative processes at magnetizing roasting, and also the processes of formation of solid solutions (Fe1-XMX3O4 and stabilization of Fe1-XO from eutectoid disintegration at cooling.

  16. Friction and surface chemistry of some ferrous-base metallic glasses

    Science.gov (United States)

    Miyoshi, K.; Buckley, D. H.

    1982-01-01

    The friction properties of some ferrous-base metallic glasses were measured both in argon and in vacuum to a temperature of 350 C. The alloy surfaces were also analyzed with X-ray photoelectron spectroscopy to identify the compounds and elements present on the surface. The results of the investigation indicate that even when the surfaces of the amorphous alloys, or metallic glasses, are atomically clean, bulk contaminants such as boric oxide and silicon dioxide diffuse to the surfaces. Friction measurements in both argon and vacuum indicate that the alloys exhibit higher coefficients of friction in the crystalline state than they do in the amorphous state.

  17. Clean ferrous casting technology research. Final technical report, September 29, 1993--December 31, 1995

    Energy Technology Data Exchange (ETDEWEB)

    Bates, C.E.; Griffin, J.; Giese, S.R.; Lane, A.M. [and others

    1996-01-31

    This is the final report covering work performed on research into methods of attaining clean ferrous castings. In this program methods were developed to minimize the formation of inclusions in steel castings by using a variety of techniques which decreased the tendency for inclusions to form during melting, casting and solidification. In a second project, a reaction chamber was built to remove inclusions from molten steel using electromagnetic force. Finally, a thorough investigation of the causes of sand penetration defects in iron castings was completed, and a program developed which predicts the probability of penetration formation and indicates methods for avoiding it.

  18. Evaporation Rate of Distilled Water Drop on the Surface of Non-Ferrous Metals

    Directory of Open Access Journals (Sweden)

    Ponomarev Konstantin

    2015-01-01

    Full Text Available We studied experimentally the evaporation process of distilled water drops on the surfaces of non-ferrous metals. Investigations were conducted on the experimental setup using a shadow optical system. The main elements of this system are the source of plane-parallel light and photographic camera. According to the contact diameter change during the evaporation, three stages have been determined (spreading, pinning, depinning. It has been found, that the dependence of evaporation rate on drop volume at low temperatures appear to be well fit by a power function.

  19. Determination of TBP, HDEHP and TOPO complexed with ferrous thiocyanate by reversed phase liquid chromatography

    International Nuclear Information System (INIS)

    Akliouant, Z.; Meddour, L.; Azzouz, A.

    1992-02-01

    The present work deals with the analysis of some organophosphorus extracting agents, e.g. TBP, HDEHP and TOPO by reversed phase liquid chromatography via previous complexation with ferrous thiocyanate. The absorbance wavelengths of the resulting complexes, i.e. TBP:FeSCNK, HDEHP:FeSCNK and TOPO:FeSCNK are respectively 427, 446 and 487nm. Thus, an improvement of such a technique consists in the organophosphorus compounds detection by colorimetry. Subsequently all products and intermediates present in synthesis media can be easily analysed in the same wavelengths range without previous separation or purification

  20. Committee Reports, May 2008

    Science.gov (United States)

    2008-08-01

    The Division's Executive Committee conducted several items of business at the New Orleans meeting. Elsewhere in this issue [see p 1032] is a listing of the candidates for Division offices for Fall 2008 election, approved by the Committee and later affirmed at the Division business meeting. Among items of specific interest to Division members is a plan to have the Journal of Chemical Education send an announcement to members when each issues goes online, and the Committee approved this use of the Division email list. It also approved plans presented by Amina El-Ashmawy and the BCCE committee to proceed with a bid from Pennsylvania State University for the 2012 BCCE.

  1. Reaction mechanisms and evaluation of effective process operation for catalytic oxidation and coagulation by ferrous solution and hydrogen peroxide

    Energy Technology Data Exchange (ETDEWEB)

    Lee, S.H.; Moon, H.J.; Kim, Y.M. [Dept. of Environmental Engineering, Sangmyung Univ., Cheonan (Korea); Bae, W.K. [Dept. of Civil and Environmental Engineering, Hanyang Univ., Ansan, Kyounggi (Korea)

    2003-07-01

    This research was carried out to evaluate the removal efficiencies of COD{sub cr} and colour for the dyeing wastewater by ferrous solution and the different dosage of H{sub 2}O{sub 2} in Fenton process. In the case of H{sub 2}O{sub 2} divided dosage, 7:3 was more effective than 3:7 to remove COD{sub cr} and colour. The results showed that COD was mainly removed by Fenton coagulation, where the ferric ions are formed in the initial step of Fenton reaction. On the other hand colour was removed by Fenton oxidation rather than Fenton coagulation. This paper also aims at pursuing to investigate the effective removal mechanisms using ferrous ion coagulation, ferric ion coagulation and Fenton oxidation process. The removal mechanism of COD{sub cr} and colour was mainly coagulation by ferrous ion, ferric ion and Fenton oxidation. The removal efficiencies were dependent on the ferric ion amount at the beginning of the reaction. However the final removal efficiency of COD and colour was in the order of Fenton oxidation, ferric ion coagulation and ferrous ion coagulation. The reason of the highest removal efficiency by Fenton oxidation can be explained by the chain reactions with ferrous solution, ferric ion and hydrogen peroxide. (orig.)

  2. Functional dependency between the logistics security system and the MySAP ERP in metallurgy

    Directory of Open Access Journals (Sweden)

    P. Ranitović

    2013-10-01

    Full Text Available MySAP ERP - Enterprise Resource Planning (system - solution which provides a whole set of functions for the business analytics, finance, human resources management, logistics and corporate services has developed from SAP R/3. It is one of the main products of the SAP AG German multinational company and as such, it is a very important element of the international industrial and technological security system. By defining the functional dependency between the security systems (logistics security systems and the IT (My SAP ERP systems in metallurgy, a concept for designing MY SAP ERP system in metallurgic industry is defined, based on the security aspects.

  3. Physical metallurgy: Scientific school of the Academician V.M. Schastlivtsev

    Science.gov (United States)

    Tabatchikova, T. I.

    2016-04-01

    This paper is to honor Academician Vadim Mikhailovich Schastlivtsev, a prominent scientist in the field of metal physics and materials science. The article comprises an analysis of the topical issues of the physical metallurgy of the early 21st century and of the contribution of V.M. Schastlivtsev and of his school to the science of phase and structural transformations in steels. In 2015, Vadim Mikhailovich celebrates his 80th birthday, and this paper is timed to this honorable date. The list of his main publications is given in it.

  4. Metallurgy of mercury in Almaden: from aludel furnaces until Pacific furnaces

    International Nuclear Information System (INIS)

    Tejero-Manzanares, J.; Garrido Saenz, I.; Mata Cabrera, F.; Rubio Mesas, M. L.

    2014-01-01

    This paper shows the different types of furnaces for roasting cinnabar, used in the metallurgy of quicksilver over the centuries of exploitation of the Almaden Mines (Spain). Some of these techniques are part of our industrial heritage. They have contributed to name UNESCO World Heritage Site the vast technological legacy of these mines recently. This research contributes to close the long way of metallurgical activity from aludel furnaces until Pacif furnaces, first and lasted technology to produce on an industrial scale. It is delved into the most relevant aspects having to do with the type, evolution and number of furnaces existing on each of the periods. (Author)

  5. Proceedings of the III International Congress of Mining and Metallurgy MINEMETAL 2016

    International Nuclear Information System (INIS)

    2016-10-01

    The III International Congress of Mining and Metallurgy was inaugurated at the Plaza América Convention Center in Varadero. Professionals from 16 countries come together to promote scientific exchange for sustainable mining and to make concrete future investments to boost the development of this important sector in Cuba. Among the topics that will occupy the agenda of these days of congress stand out the development of geology, new technological processes, advances in the application of zeolite, sustainable development and care of the environment.

  6. Metallurgy department progress report for the period 1 January to 31 December 1979

    International Nuclear Information System (INIS)

    1980-07-01

    The activities of the Metallurgy Department at Risoe during 1979 are described. The work is presented in four chapters: General material research, technology and materials development, fuel elements, non-destructive testing. An article on wingblades of glass fibre reinforced polyester for a 630 kW windturbine is also included. Furthermore, a survey is given of the department's participation in international collaboration and of its activities within education and training. A list (with abstracts) of publications and lectures by the staff during 1979 is included. (author)

  7. Accelerated Near-Threshold Fatigue Crack Growth Behavior of an Aluminum Powder Metallurgy Alloy

    Science.gov (United States)

    Piascik, Robert S.; Newman, John A.

    2002-01-01

    Fatigue crack growth (FCG) research conducted in the near threshold regime has identified a room temperature creep crack growth damage mechanism for a fine grain powder metallurgy (PM) aluminum alloy (8009). At very low DK, an abrupt acceleration in room temperature FCG rate occurs at high stress ratio (R = Kmin/Kmax). The near threshold accelerated FCG rates are exacerbated by increased levels of Kmax (Kmax less than 0.4 KIC). Detailed fractographic analysis correlates accelerated FCG with the formation of crack-tip process zone micro-void damage. Experimental results show that the near threshold and Kmax influenced accelerated crack growth is time and temperature dependent.

  8. 77 FR 27832 - Shipping Coordinating Committee; Notice of Committee Meeting

    Science.gov (United States)

    2012-05-11

    ... organizations --Relations with non-governmental organizations --World Maritime Day --International Maritime... DEPARTMENT OF STATE [Public Notice: 7879] Shipping Coordinating Committee; Notice of Committee...-second Session of the International Maritime Organization (IMO) Technical Co-operation Committee (TCC 62...

  9. 78 FR 32698 - Shipping Coordinating Committee; Notice of Committee Meeting

    Science.gov (United States)

    2013-05-31

    ... intergovernmental organizations --Relations with non-governmental organizations --World Maritime Day --International... DEPARTMENT OF STATE [Public Notice 8340] Shipping Coordinating Committee; Notice of Committee... Session of the International Maritime Organization (IMO) Technical Co-operation Committee (TCC 63) to be...

  10. Study on the formation of cubic texture in Ni-7 at.% W alloy substrates by powder metallurgy routes

    DEFF Research Database (Denmark)

    Zhao, Yue; Suo, HongLi; Zhu, YongHua

    2009-01-01

    One of the main challenges for coated conductor applications is to produce sharp cubic textured alloy substrates with high strength and low magnetism. In this work, the cubic textured Ni–7 at.% W substrates were prepared from different powder metallurgy ingots by rolling-assisted biaxially textured...... substrate processing. The fabrication processes of cubic texture in the Ni–7 at.% W tapes by two powder metallurgy routes are described in detail. Through the optimized process, full width at half maximum values of 6.7° and 5.0° were obtained, as estimated by X-ray (1 1 1) phi scan and (2 0 0) rocking curve...

  11. Study on fluorescence properties of carbogenic nanoparticles and their application for the determination of ferrous succinate

    Energy Technology Data Exchange (ETDEWEB)

    Sun Wen [Department of Analytical Chemistry, China Pharmaceutical University, Nanjing 210009 (China); Du Yingxiang, E-mail: du_yingxiang@126.co [Department of Analytical Chemistry, China Pharmaceutical University, Nanjing 210009 (China) and Key Laboratory of Drug Quality Control and Pharmacovigilance, Ministry of Education, China Pharmaceutical University, Nanjing 210009 (China) and Key Laboratory of Modern Chinese Medicines, Ministry of Education, China Pharmaceutical University, Nanjing 210009 (China); Wang Yunqing [Yantai Institute of Coastal Zone Research, Chinese Academy of Sciences, Yantai 264003 (China)

    2010-08-15

    A new type of fluorescent nanomaterial named carbogenic nanoparticles (NPs) has drawn considerable attention recently. In this study, we adopted a direct and simple synthetic method to produce the carbogenic NPs and investigated the fluorescence properties of the as-prepared carbogenic NPs in detail. It was found that the fluorescence of carbogenic NPs was stable with the variance of environmental conditions such as pH, temperature and UV irradiation. More interestingly, we found carbogenic NPs exhibited high selectivity and sensitivity towards ferric ions. Under optimum conditions, a good linear relationship could be obtained between the fluorescence intensity and concentration of ferric ions in the range of 5.0x10{sup -5}-5.0x10{sup -4} mol L{sup -1}, and the limit of detection is 11.2 {mu}mol L{sup -1}. Based on the fluorescence quenching of carbogenic NPs, a rapid and specific quantitative method was proposed for the determination of ferrous succinate. The content of ferrous succinate in commercial tablets determined by the present method was agreed with the spectrophotometric method results and the reproducibility and the recovery of the proposed method were satisfactory.

  12. Prospects for Ukrainian ferrous metals in the post-soviet period

    Science.gov (United States)

    Levine, R.M.; Bond, A.R.

    1998-01-01

    Two specialists on the mineral industries of the countries of the former USSR survey current problems confronting producers of ferrous metals in Ukraine and future prospects for domestic production and exports. A series of observations documenting the importance of ferrous metals production to Ukraine's economy is followed by sections describing investment plans and needs in the sector, and the role played by Ukraine within the iron and steel industry of the Soviet Union. The focus then turns to assessment of the current regional and global competitive position of Ukrainian producers for each of the major commodities of the sector-iron ore, manganese ore, ferroalloys, steel, and the products of the machine manufacturing and metal working industries. In conclusion, the paper discusses a potential regional industrial integration strategy analogous to that employed in the United States' Great Lakes/Midwest region, which possesses similar types of iron ore deposits and similar transport cost advantages and metallurgical and manufacturing industries. Journal of Economic Literature, Classification Numbers: F14, L61, L72. 1 table, 26 references.

  13. Molecular characterization of whey protein hydrolysate fractions with ferrous chelating and enhanced iron solubility capabilities.

    Science.gov (United States)

    O'Loughlin, Ian B; Kelly, Phil M; Murray, Brian A; FitzGerald, Richard J; Brodkorb, Andre

    2015-03-18

    The ferrous (Fe2+) chelating capabilities of WPI hydrolysate fractions produced via cascade membrane filtration were investigated, specifically 1 kDa permeate (P) and 30 kDa retentate (R) fractions. The 1 kDa-P possessed a Fe2+ chelating capability at 1 g L(-1) equivalent to 84.4 μM EDTA (for 30 kDa-R the value was 8.7 μM EDTA). Fourier transformed infrared (FTIR) spectroscopy was utilized to investigate the structural characteristics of hydrolysates and molecular interactions with Fe2+. Solid-phase extraction was employed to enrich for chelating activity; the most potent chelating fraction was enriched in histidine and lysine. The solubility of ferrous sulfate solutions (10 mM) over a range of pH values was significantly (Piron solubility was improved by 72% in the presence of the 1 kDa-P fraction following simulated gastrointestinal digestion (SGID) compared to control FeSO4·7H2O solutions.

  14. Solid ferrous ammonium sulfate as a dosimeter at low temperatures and high doses

    International Nuclear Information System (INIS)

    Juarez-calderon, J.M.; Ramos B, S.; Negron M, A.

    2006-01-01

    This paper presents the results obtained from a study of the radiation induced oxidation of crystalline ferrous ammonium sulfate with gamma rays at 295 K, 263 K and 77 K and doses from 0 to 300 kGy. The radiation induced decomposition of ferrous ammonium sulfate has been studied by the dissolution of the irradiated salt in 0,8 N sulfuric acid. The main product is ferric ion (Fe 3+ ) and its molar concentration was determined spectrophotometrically in the UV region at 304 nm. The optical density values showed a linear dependence with dose, indicating that the data obtained might be used to create a calibrating curve. Color in irradiated salt changes from blue to green, yellow and orange according to the absorbed dose. The accuracy and the reproducibility of the system were tested. In addition, some other characteristics make possible the use of this system as a dosimeter, similar to Fricke chemical dosimeter, for studies and works at low temperatures and high doses. (authors)

  15. Solid ferrous ammonium sulfate as a dosimeter at low temperatures and high doses

    Energy Technology Data Exchange (ETDEWEB)

    Juarez-calderon, J.M.; Ramos B, S.; Negron M, A. [Mexico Univ. Nacional Autonoma, Instituto de Ciencias Nucleares (Mexico)

    2006-07-01

    This paper presents the results obtained from a study of the radiation induced oxidation of crystalline ferrous ammonium sulfate with gamma rays at 295 K, 263 K and 77 K and doses from 0 to 300 kGy. The radiation induced decomposition of ferrous ammonium sulfate has been studied by the dissolution of the irradiated salt in 0,8 N sulfuric acid. The main product is ferric ion (Fe{sup 3+}) and its molar concentration was determined spectrophotometrically in the UV region at 304 nm. The optical density values showed a linear dependence with dose, indicating that the data obtained might be used to create a calibrating curve. Color in irradiated salt changes from blue to green, yellow and orange according to the absorbed dose. The accuracy and the reproducibility of the system were tested. In addition, some other characteristics make possible the use of this system as a dosimeter, similar to Fricke chemical dosimeter, for studies and works at low temperatures and high doses. (authors)

  16. Study of dosimetric systems-ferrous sulfate-ferric sulfate, glass slides and dyed aqueous solutions

    International Nuclear Information System (INIS)

    Fernandes, L.

    1979-01-01

    The effect of some variables which can effect the preparation of the ferrous sulfate used as dosimetric solution has been studied. Among these variables the purity of the water used for the preparation of the solution and the presence (or absence) of oxygen in the dosimetric solution were considered. The dose rate distribution according to the transverse and longitudinal sections of the Co 60 irradiator was studied experimentally, using the dosimetric solution, and theoretically, using a computer program (KIFE). The results obtained with the ferrous sulface dosimetric solution were used as reference for the study of the application of EM and MSG glass slide as a dosimetric system. For this purpose the effects of the weakening of the coloration induced in the glass by gamma rays (Co 60 ) and the relationship between the absorbed dose of radiation and the ratio between the variation in absorbation value and the thickness of the glass irradiated, were studied. A study was also made of the use of the dye indicators bromothymol-blue, methyl-orange, Congo-red, neutral-red and p-nitrophenol, in aqueous solution, for radiation dose measurements. The bleaching of each indicator solution, under gamma-radiation (Co 60 ) was studied in oxygen and nitrogen atmospheres.(Author) [pt

  17. Recovery of ferrous and nonferrous metal from ASR by physical separation

    Science.gov (United States)

    Kim, Min-gyu; Han, Oh-hyung; Park, Chul-hyun

    2017-04-01

    A recycle ratio of waste automobiles in Korea is low, compared to that of the advanced countries. Especially in its recycle, separation of automotive shredder residue (ASR), the residual fraction of approximate 25% obtained after dismantling and shredding from waste car, is needed. However ASR is cannot be effectively separated due to its heterogeneous materials and coated or laminated complexes and then is largely deposited in land-fill sites as waste. In this study ASR was separated by a series of physical processing operations such as comminution, air classification and magnetic separation and electrostatic separations. In particular it focuses on estimating the optimal conditions of magnetic and electrostatic separations for improving the separation efficiency of valuable ferrous and non-ferrous metals such as iron (Fe), aluminum, copper and etc. In magnetic separation, 91.5% Fe grade and 91% recovery could be obtained at conditions of particle size under 10mm and magnetic intensity of 400 gauss. In corona electrostatic separation for recovering nonferrous metals, a grade of 79.2% and recovery of 90.7% could be successfully achieved under conditions of -6mm particle size, 50kV electrode potential, 35rpm drum speed and 20 degree splitter position, respectively. Acknowledgments This study was supported by the R&D Center for Valuable Recycling (Global-Top R&BD Program) of the Ministry of Environment. (Project No. 2016002250001)

  18. Preparation, physical characterization, and stability of Ferrous-Chitosan microcapsules using different iron sources

    Science.gov (United States)

    Handayani, Noer Abyor; Luthfansyah, M.; Krisanti, Elsa; Kartohardjono, Sutrasno; Mulia, Kamarza

    2017-11-01

    Dietary modification, supplementation and food fortification are common strategies to alleviate iron deficiencies. Fortification of food is an effective long-term approach to improve iron status of populations. Fortification by adding iron directly to food will cause sensory problems and decrease its bioavailability. The purpose of iron encapsulation is: (1) to improve iron bioavailability, by preventing oxidation and contact with inhibitors and competitors; and (2) to disguise the rancid aroma and flavor of iron. A microcapsule formulation of two suitable iron compounds (iron II fumarate and iron II gluconate) using chitosan as a biodegradable polymer will be very important. Freeze dryer was also used for completing the iron microencapsulation process. The main objective of the present study was to prepare and characterize the iron-chitosan microcapsules. Physical characterization, i.e. encapsulation efficiency, iron loading capacity, and SEM, were also discussed in this paper. The stability of microencapsulated iron under simulated gastrointestinal conditions was also investigated, as well. Both iron sources were highly encapsulated, ranging from 71.5% to 98.5%. Furthermore, the highest ferrous fumarate and ferrous gluconate loaded were 1.9% and 4.8%, respectively. About 1.04% to 9.17% and 45.17% to 75.19% of Fe II and total Fe, were released in simulated gastric fluid for two hours and in simulated intestinal fluid for six hours, respectively.

  19. Effect of ferrous ion on ε-poly-L-lysine biosynthesis by Streptomyces diastatochromogenes CGMCC3145.

    Science.gov (United States)

    Wang, Guoliang; Jia, Shiru; Wang, Tian; Chen, Liye; Song, Qingchao; Li, Weina

    2011-03-01

    ε-Poly-L-lysine (ε-PL) is known as an amino acid homopolymer occurring in nature. It is mainly produced by bacteria belonging to the family of Streptomycetaceae. In this study, the effect of ferrous ion on the metabolic pathway such as key enzyme activities and substrate consumptions relating to ε-PL production were investigated. When 0.1 mM Fe(2+) was supplemented into the culture medium of Streptomyces diastatochromogenes CGMCC3145 for 72 h of cultivation, the yield of ε-PL and biomass were enhanced by 29.2 and 41.9%, respectively, compared with those of the control. Synchronously, consumptions of glucose, ammoniac nitrogen, and phosphorus were increased by 50, 67.6, and 35.7%, respectively. The enzyme activity measurements showed that the specific activities of proteinase, phosphatase, glutamate dehydrogenase, and aspartate aminotransferase activities were improved for 2.32, 3.68, 1.72, and 1.50 folds, respectively, however, aspartokinase and ε-PL synthetase were hardly affected by ferrous ion. These results manifested that Fe(2+) can improve the yield of ε-PL by promoting aspartate production, and the aspartate was further catalyzed to produce much more L-lysine, precursor for ε-PL biosynthesis.

  20. Ferrous Ion and Medium Composition Effects on Acidogenic Phase in Biobutanol Production from Molasses

    Science.gov (United States)

    Restiawaty, E.; Grinanda, D.

    2017-07-01

    Clostridium acetobutylicum B530 has ability to convert sugar into biobutanol through two phases, i.e. acidogenic and solventogenic. This fermentation process is often hampered by high raw material cost and low product yield. In order to suppress the production cost, the molasses, a byproduct of sugar cane process production, was used as carbon source in this research. Molasses has nitrogen content in a small amount, thus could be negating the beef extract component, which is expected not to affect the growth of C. acetobutylicum B530 and also can reduce the production cost. In addition, a certain amount of Fe2+ (ferrous ion), a precursor in the formation of the enzyme ferredoxin, was added to the fermentation medium to contribute in the synthesis of acetyl-CoA, so that the formation of acidogenic products such as butyric acid and acetic acid is affected. This study aimed to investigate the effect of ferrous ion and the medium composition in acidogenic phase. The addition of 20 ppm FeSO4.7H2O in the fermentation medium without beef extract can increase the concentration of butyric acid by 20% at a temperature of 35°C, while acetic acid concentration decreased by 6%. According to those results, it is expected that the product selectivity of butanol will increase in solventogenic phase. In addition, the removal of beef extract in the fermentation medium does not affect the kinetics of growth of C. acetobutylicum B530.

  1. The photochemical origins of life and photoreaction of ferrous ion in the archaean oceans

    Science.gov (United States)

    Mauzerall, David C.

    1990-01-01

    A general argument is made for the photochemical origins of life. A constant flux of free energy is required to maintain the organized state of matter called life. Solar photons are the unique source of the large amounts of energy probably required to initiate this organization and certainly required for the evolution of life to occur. The completion of this argument will require the experimental determination of suitable photochemical reactions. It is shown that biogenetic porphyrins readily photooxidize substrates and emit hydrogen in the presence of a catalyst. These results are consistent with the Granick hypothesis, which relates a biosynthetic pathway to its evolutionary origin. It has been shown that photoexcitation of ferrous ion at neutral pH with near ultraviolet light produces hydrogen with high quantum yield. This same simple system may reduce carbon dioxide to formaldehyde and further products. These reactions offer a solution to the dilemma confronting the Oparin-Urey-Miller model of the chemical origin of life. If carbon dioxide is the main form of carbon on the primitive earth, the ferrous photoreaction may provide the reduced carbon necessary for the formation of amino acids and other biogenic molecules. These results suggest that this progenitor of modern photosynthesis may have contributed to the chemical origins of life.

  2. Ethics committees in Croatia

    NARCIS (Netherlands)

    Borovecki, Ana

    2007-01-01

    In this thesis the work of ethics committees in Croatia is being investigated for the first time. The 1997 Law on Health Protection introduced legal standards for the establishment of the so-called 'mixed' type of ethics committees in healthcare institutions. Our study aims to examine whether this

  3. The Effect of Ferrous Nano-oxide Particles on Physiological Traits and Nutritional Compounds of Soybean ( Glycine max L.) Seed.

    Science.gov (United States)

    Sheykhbaglou, Roghayyeh; Sedghi, Mohammad; Fathi-Achachlouie, Bahram

    2018-02-19

    Soybean (Glycine max L.) seed contains amounts of protein, lipid, carbohydrate and mineral elements, which protein and lipid have been known as a main part for soybean's trade value. In this study, in order to investigate the effect of ferrous nano-oxide particles on nutritional compounds of soybean seed, an experiment with 5 treatments and 3 replications was conducted as a randomized complete block design. Treatments were 5 concentrations of ferrous nano-oxide particles including 0, 0.25, 0.5, 0.75 and 1 g L-1 which were sprayed 3 times at 4 and 8 leaves stage and pod initiation. Lipid and protein contents, fatty acids profile, some of mineral elements such as Fe, Mg, Ca and P, chlorophyll a, b and total chlorophyll content were determined. Results showed that solution containing ferrous nano-oxide particles had significant effect on nutritional compounds of soybean seed (P<0.01) compared to control. The highest content of lipid and protein (25.4 and %33.8, respectively) observed by applying 0.75 g L-1 of ferrous nano-oxide and the lowest content was also in control. Changes in the trends of fatty acids profile (palmitic, oleic, linoleic and linolenic acids), some of mineral elements (Fe, Mg, Ca and P) and chlorophyll contents were similar to lipid and protein levels which by increasing in concentration of ferrous nano-oxide from 0 to 0.75 g L-1 all measured parameters also increased, but reduction in all parameters was observed in concentration from 0.75 to 1 g L-1. In conclusion, application of 0.75 to 1 g L-1 ferrous nano-oxide had the best effect on the nutrient composition of soybean seed.

  4. The synthesis and characterization of Mg-Zn-Ca alloy by powder metallurgy process

    Energy Technology Data Exchange (ETDEWEB)

    Annur, Dhyah; Franciska, P.L.; Erryani, Aprilia; Amal, M. Ikhlasul; Kartika, Ika, E-mail: pepeng2000@yahoo.com [Research center for Metallurgy and Material, Indonesian Institute of Science (Indonesia); Sitorus, Lyandra S. [Sultan Ageng Tirtayasa University (Indonesia)

    2016-04-19

    Known for its biodegradation and biocompatible properties, magnesium alloys have gained many interests to be researched as implant material. In this study, Mg-3Zn-1Ca, Mg-29Zn-1Ca, and Mg-53Zn-4.3Ca (in wt%) were synthesized by means of powder metallurgy method. The compression strength and corrosion resistance of magnesium alloy were thoroughly examined. The microstructures of the alloy were characterized using optical microscopy, Scanning Electron Microscope, and also X-ray diffraction analysis. The corrosion resistance were evaluated using electrochemical analysis. The result indicated that Mg- Zn- Ca alloy could be synthesized using powder metallurgy method. This study showed that Mg-29Zn-1Ca would make the highest mechanical strength up to 159.81 MPa. Strengthening mechanism can be explained by precipitation hardening and grain refinement mechanism. Phase analysis had shown the formation of α Mg, MgO, and intermetallic phases: Mg2Zn11 and also Ca2Mg6Zn3. However, when the composition of Zn reach 53% weight, the mechanical strength will be decreasing. In addition, all of Mg-Zn-Ca alloy studied here had better corrosion resistance (Ecorr around -1.4 VSCE) than previous study of Mg. This study indicated that Mg- 29Zn- 1Ca alloy can be further analyzed to be a biodegradable implant material.

  5. Development of processes for zircaloy chips recycling by electric arc furnace remelting and powder metallurgy

    International Nuclear Information System (INIS)

    Pereira, Luiz Alberto Tavares

    2014-01-01

    PWR reactors employ, as nuclear fuel, UO 2 pellets with Zircaloy clad. In the fabrication of fuel element parts, machining chips from the alloys are generated. As the Zircaloy chips cannot be discarded as ordinary metallic waste, the recycling of this material is important for the Brazilian Nuclear Policy, which targets the reprocess of Zircaloy residues for economic and environmental aspects. This work presents two methods developed in order to recycle Zircaloy chips. In one of the methods, Zircaloy machining chips were refused using an electric-arc furnace to obtain small laboratory ingots. The second one uses powder metallurgy techniques, where the chips were submitted to hydriding process and the resulting material was milled, isostatically pressed and vacuum sintered. The ingots were heat-treated by vacuum annealing. The microstructures resulting from both processing methods were characterized using optical and scanning electron microscopy. Chemical composition, crystal phases and hardness were also determined. The results showed that the composition of recycled Zircaloy comply with the chemical specifications and presented adequate microstructure for nuclear use. The good results of the powder metallurgy method suggest the possibility of producing small parts, like cladding end-caps, using near net shape sintering. (author)

  6. Microstructural and electrical investigation of Cu-Ni-Cr alloys obtained by powder metallurgy method

    Energy Technology Data Exchange (ETDEWEB)

    Carrio, Juan A.G.; Carvalhal, M.A.; Ayabe, L.M.; Monteiro, W.A., E-mail: jgcarrio@mackenzie.br [Universidade Presbiteriana Mackenzie (UPM/CCH), Sao Paulo, SP (Brazil). Centro de Ciencias e Humanidades. Dept. de Fisica; Silva, L.C.E. da; Silva Junior, R.V., E-mail: fisica.cch@mackenzie.br [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

    2009-07-01

    The aim of this work, using the powder metallurgy process, is to synthesize metallic alloys with high mechanical strength and high electric conductivity, after melting optimizing and thermal treatments. The Cu-Ni-Cr (wt%) alloys are characterized in their mechanical and electrical properties as well as the obtained microstructure. Through the process of powder metallurgy, contacts and structural parts can be obtained. The alloys elements are added to copper with the intention to improve their strength, ductility and thermal stability, without causing considerable damages in their form, electrical and thermal conductivity, and corrosion resistance. The metallic powders were mixed for a suitable time and then they were pressed in a cold uniaxial pressing (1000 kPa). Afterwards, the specimens were sintered in temperatures varying from 700 up to 800 deg C under vacuum. At last, the samples were homogenized at 550 deg C under vacuum, for special times. The comparative analysis is based on the sintered density, densification parameter, hardness, macrostructures and microstructures of the samples. The alloys were characterized by optical microscopy, X-rays powder diffraction, electrical conductivity and Vickers hardness. (author)

  7. Summary of NRC LWR safety research programs on fuel behavior, metallurgy/materials and operational safety

    International Nuclear Information System (INIS)

    Bennett, G.L.

    1979-09-01

    The NRC light-water reactor safety-research program is part of the NRC regulatory program for ensuring the safety of nuclear power plants. This paper summarizes the results of NRC-sponsored research into fuel behavior, metallurgy and materials, and operational safety. The fuel behavior research program provides a detailed understanding of the response of nuclear fuel assemblies to postulated off-normal or accident conditions. Fuel behavior research includes studies of basic fuel rod properties, in-reactor tests, computer code development, fission product release and fuel meltdown. The metallurgy and materials research program provides independent confirmation of the safe design of reactor vessels and piping. This program includes studies on fracture mechanics, irradiation embrittlement, stress corrosion, crack growth, and nondestructive examination. The operational safety research provides direct assistance to NRC officials concerned with the operational and operational-safety aspects of nuclear power plants. The topics currently being addressed include qualification testing evaluation, fire protection, human factors, and noise diagnostics

  8. Acoustic harmonic generation measurement applications: Detection of tight cracks in powder metallurgy compacts

    International Nuclear Information System (INIS)

    Barnard, D.J.; Foley, J.C.

    2000-01-01

    Standard linear ultrasonic testing techniques have long been employed for locating and characterizing relatively open cracks in a wide variety of materials, from metallic alloys and ceramics to composites. In all these materials, the detection of open cracks easily accomplished because the void between the two crack surfaces provides sufficient acoustic impedance mismatch to reflect the incident energy. Closed or partially closed cracks, however, may often go undetected because contacting interfaces allow transmission of ultrasound. In the green (unsintered) state, powder metallurgy compacts typically contain high residual stresses that have the ability to close cracks formed during the compaction process, a result of oxide films, improper powder lubricant, mold design, etc. After sintering, the reduction of residual stresses may no longer be sufficient to close the crack. Although the crack may be more easily detected, it is obvious most desirable to discover defects prior to sintering. It has been shown that the displacements of an interface may be highly nonlinear if a stress wave of sufficient intensity propagates across it, a result of the stress wave either opening or closing the interface. Current efforts involve the application of nonlinear acoustic techniques, in particular acoustic harmonic generation measurements, for the detection and characterization of tightly closed cracks in powder metallurgy parts. A description of the equipment and the measurement technique will be discussed and initial experimental results on sintered and green compacts will be presented. - This work was performed at the Ames Laboratory, Iowa State University under USDOE Contract No. W-7405-ENG-82

  9. Characterization of aluminum/steel components from recycled swarf using the powder metallurgy as technique

    International Nuclear Information System (INIS)

    Souza, V.E.S.; Masieiro, F.R.S.; Lourenco, J.M.; Felipe, R.C.T.S.

    2009-01-01

    Full text: The powder metallurgy process consists to produce metallic or ceramic components through pressure in a powder mass. These components will be submitted to a sintering temperature in order to consolidate them and then improve their mechanical proprieties. The industry is responsible for the swarf generation from different manufacture process. This paper has main goal the reutilization of aluminum and steel swarf using the powder metallurgy as technique. The methodology used in this work consists to compact Al 6060 plus steel SAE 1045 as reinforce material at 250MPa, 400MPa and 600MPa. The composition about these compacted will be 30%, 40%, 50% of steel into aluminum matrix. In this way will be analyze the hardness as function of the compressibility and quantity of steel. The samples will be processed at 500°C during 45 minutes using a resistive furnace in a hydrogen atmosphere. Micrographs of the sintered samples will be obtained by using a Scanning Electron Microscope and Optic Microscope. X-rays diffraction will be also used to characterize the phases found to due diffusivity between the steel and aluminum. (author)

  10. Development of an extra-high strength powder metallurgy nickel-base superalloy

    Science.gov (United States)

    Kent, W. B.

    1977-01-01

    A program was conducted to optimize the composition of NASA IIb-11, an alloy originally developed as a wrought material, for thermal stability and to determine the feasibility for producing the alloy using powder metallurgy techniques. Seven compositions were melted and atomized, hot isostatically pressed, cross rolled to disks and heat treated. Tensile and stress rupture properties from room temperature to 870 C (1600 F) were determined in addition to thermal stability characteristics. Processing variables included hot isostatic pressing parameters and handling, cross rolling procedures and heat treatment cycles. NASA IIb-11E displayed the best combination of overall properties for service as a 760 C (1400 F) disk material. Its composition is 0.06 C, 8.5 Cr, 9.0 Co, 2.0 Mo, 7.1 W, 6.6 Ta, 4.5 Al, 0.75 Ti, 0.5 V, 0.7 Hf, 0.01 B, 0.05 Zr and balance Ni. While the alloy exhibits the highest 760 C (1400 F) rupture strength reported for any powder metallurgy disk alloy to date, additional studies to further evaluate the effects of heat treatment may be required. The alloy is not susceptible to topologically close-packed phase formation during thermal exposure at 870 C (1600 F) for 1,500 hours, but its mechanical property levels are lowered due to grain boundary carbide formation.

  11. Analysis of cancer mortality risk among workers of a research uranium metallurgy division in France

    International Nuclear Information System (INIS)

    Jejati, H.; Laurier, D.; Tirmarche, M.; Giraud, J.M.

    1997-01-01

    This cohort study has been undertaken in response to a suspected cluster of cancers mentioned by workers involved in research activities concerning the metallurgy of uranium. The studied population included all persons having worked between 1950 and 1968 at the Metallurgy Division of the French Atomic Energy Commission (CEA). Exposures were registered on an individual annual basis. For analysis, they were grouped in three categories: use of chemicals agents (Benzene, beryllium, alcohols, solvents ...), manipulation of radioactive materials (uranium, thorium, fission decay products), and exposure to external radiation. This relatively small cohort included 356 workers followed up to December 1990. Out of observed deaths, 21 were from cancer. Total mortality from cancer was less than expected from national rates (Standardised Mortality Ratio = 0.73). Cancer mortality did not increase with duration of exposure to external radiation or with duration of manipulation of radioactive materials. Risk of cancer was increasing with the number of years of exposure to chemicals. The small size of this cohort limits the conclusion of the observed results. The purpose, despite this lack of power, was to answer a worry of the workers, more than to estimate a clear dose-response relationship linked to a specific cancer site. The effect studied here is ''all cancers'', a distinction of the different sites being uninformative because of the very small number of cases observed. Nevertheless, this study suggests some routes for further research: it highlights the importance of considering concomitant exposures like chemical ones in studies of nuclear workers. (author)

  12. Metallurgy of high-silicon steel parts produced using Selective Laser Melting

    International Nuclear Information System (INIS)

    Garibaldi, Michele; Ashcroft, Ian; Simonelli, Marco; Hague, Richard

    2016-01-01

    The metallurgy of high-silicon steel (6.9%wt.Si) processed using Selective Laser Melting (SLM) is presented for the first time in this study. High-silicon steel has great potential as a soft magnetic alloy, but its employment has been limited due to its poor workability. The effect of SLM-processing on the metallurgy of the alloy is investigated in this work using microscopy, X-Ray Diffraction (XRD) and Electron Backscatter Diffraction (EBSD). XRD analysis suggests that the SLM high-silicon steel is a single ferritic phase (solid solution), with no sign of phase ordering. This is expected to have beneficial effects on the material properties, since ordering has been shown to make silicon steels more brittle and electrically conductive. For near-fully dense samples, columnar grains with a high aspect ratio and oriented along the build direction are found. Most importantly, a <001> fibre-texture along the build direction can be changed into a cube-texture when the qualitative shape of the melt-pool is altered (from shallow to deep) by increasing the energy input of the scanning laser. This feature could potentially open the path to the manufacture of three-dimensional grain-oriented high-silicon steels for electromechanical applications.

  13. Porous titanium scaffolds fabricated using a rapid prototyping and powder metallurgy technique.

    Science.gov (United States)

    Ryan, Garrett E; Pandit, Abhay S; Apatsidis, Dimitrios P

    2008-09-01

    One of the main issues in orthopaedic implant design is the fabrication of scaffolds that closely mimic the biomechanical properties of the surrounding bone. This research reports on a multi-stage rapid prototyping technique that was successfully developed to produce porous titanium scaffolds with fully interconnected pore networks and reproducible porosity and pore size. The scaffolds' porous characteristics were governed by a sacrificial wax template, fabricated using a commercial 3D-printer. Powder metallurgy processes were employed to generate the titanium scaffolds by filling around the wax template with titanium slurry. In the attempt to optimise the powder metallurgy technique, variations in slurry concentration, compaction pressure and sintering temperature were investigated. By altering the wax design template, pore sizes ranging from 200 to 400 microm were achieved. Scaffolds with porosities of 66.8 +/- 3.6% revealed compression strengths of 104.4+/-22.5 MPa in the axial direction and 23.5 +/- 9.6 MPa in the transverse direction demonstrating their anisotropic nature. Scaffold topography was characterised using scanning electron microscopy and microcomputed tomography. Three-dimensional reconstruction enabled the main architectural parameters such as pore size, interconnecting porosity, level of anisotropy and level of structural disorder to be determined. The titanium scaffolds were compared to their intended designs, as governed by their sacrificial wax templates. Although discrepancies in architectural parameters existed between the intended and the actual scaffolds, overall the results indicate that the porous titanium scaffolds have the properties to be potentially employed in orthopaedic applications.

  14. Environmental legacy of copper metallurgy and Mongol silver smelting recorded in Yunnan Lake sediments.

    Science.gov (United States)

    Hillman, Aubrey L; Abbott, Mark B; Yu, JunQing; Bain, Daniel J; Chiou-Peng, TzeHuey

    2015-03-17

    Geochemical measurements on well-dated sediment cores from Lake Er (Erhai) are used to determine the timing of changes in metal concentrations over 4500 years in Yunnan, a borderland region in southwestern China noted for rich mineral deposits but with inadequately documented metallurgical history. Our findings add new insight into the impacts and environmental legacy of human exploitation of metal resources in Yunnan history. We observe an increase in copper at 1500 BC resulting from atmospheric emissions associated with metallurgy. These data clarify the chronological issues related to links between the onset of Yunnan metallurgy and the advent of bronze technology in adjacent Southeast Asia, subjects that have been debated for nearly half a century. We also observe an increase from 1100 to 1300 AD in a number of heavy metals including lead, silver, zinc, and cadmium from atmospheric emissions associated with silver smelting. Culminating during the rule of the Mongols, known as the Yuan Dynasty (1271-1368 AD), these metal concentrations approach levels three to four times higher than those from industrialized mining activity occurring within the catchment today. Notably, the concentrations of lead approach levels at which harmful effects may be observed in aquatic organisms. The persistence of this lead pollution over time created an environmental legacy that likely contributes to known issues in modern day sediment quality. We demonstrate that historic metallurgical production in Yunnan can cause substantial impacts on the sediment quality of lake systems, similar to other paleolimnological findings around the globe.

  15. Microstructural and mechanical characteristics of porous iron prepared by powder metallurgy.

    Science.gov (United States)

    Capek, Jaroslav; Vojtěch, Dalibor

    2014-10-01

    The demand for porous biodegradable load-bearing implants has been increasing recently. Based on investigations of biodegradable stents, porous iron may be a suitable material for such applications. In this study, we prepared porous iron samples with porosities of 34-51 vol.% by powder metallurgy using ammonium bicarbonate as a space-holder material. We studied sample microstructure (SEM-EDX and XRD), flexural and compressive behaviors (universal loading machine) and hardness HV5 (hardness tester) of the prepared samples. Sample porosity increased with the amount of spacer in the initial mixtures. Only the pore surfaces had insignificant oxidation and no other contamination was observed. Increasing porosity decreased the mechanical properties of the samples; although, the properties were still comparable with human bone and higher than those of porous non-metallic biomaterials and porous magnesium prepared in a similar way. Based on these results, powder metallurgy appears to be a suitable method for the preparation of porous iron for orthopedic applications. Copyright © 2014 Elsevier B.V. All rights reserved.

  16. Fractionation study in bioleached metallurgy wastes using six-step sequential extraction.

    Science.gov (United States)

    Krasnodebska-Ostrega, Beata; Pałdyna, Joanna; Kowalska, Joanna; Jedynak, Łukasz; Golimowski, Jerzy

    2009-08-15

    The stored metallurgy wastes contain residues from ore processing operations that are characterized by relatively high concentrations of heavy metals. The bioleaching process makes use of bacteria to recover elements from industrial wastes and to decrease potential risk of environmental contamination. Wastes were treated by solutions containing bacteria. In this work, the optimized six-stage sequential extraction procedure was applied for the fractionation of Ni, Cr, Fe, Mn, Cu and Zn in iron-nickel metallurgy wastes deposited in Southern Poland (Szklary). Fractionation and total concentrations of elements in wastes before and after various bioleaching treatments were studied. Analyses of the extracts were performed by ICP-MS and FAAS. To achieve the most effective bioleaching of Zn, Cr, Ni, Cu, Mn, Fe the usage of both autotrophic and heterotrophic bacteria in sequence, combined with flushing of the residue after bioleaching is required. 80-100% of total metal concentrations were mobilized after the proposed treatment. Wastes treated according to this procedure could be deposited without any risk of environmental contamination and additionally the metals could be recovered for industrial purposes.

  17. Pesticide Program Dialogue Committee (PPDC)

    Science.gov (United States)

    The Pesticide Program Dialogue Committee, a permanent, broadly representative advisory committee, meets with EPA on a regular basis to discuss pesticide regulatory, policy, and program implementation issues.

  18. The Audit Committee. Effective Committees. Board Basics.

    Science.gov (United States)

    Ostrom, John S.

    1996-01-01

    In many colleges and universities the responsibility of the governing board's audit committee is to arrange and oversee regular audits of financial activities, comply with donor restrictions on gifts, adhere to laws and regulations, and conform to established board policies. Membership of three to five is usually sufficient, and while the…

  19. Iron deficiency up-regulates iron absorption from ferrous sulphate but not ferric pyrophosphate and consequently food fortification with ferrous sulphate has relatively greater efficacy in iron-deficient individuals

    NARCIS (Netherlands)

    Zimmermann, M.B.; Biebinger, R.; Egli, I.; Zeder, C.; Hurrell, R.F.

    2011-01-01

    Fe absorption from water-soluble forms of Fe is inversely proportional to Fe status in humans. Whether this is true for poorly soluble Fe compounds is uncertain. Our objectives were therefore (1) to compare the up-regulation of Fe absorption at low Fe status from ferrous sulphate (FS) and ferric

  20. 75 FR 43156 - Federal Advisory Committee; Missile Defense Advisory Committee

    Science.gov (United States)

    2010-07-23

    ... Office of the Secretary Federal Advisory Committee; Missile Defense Advisory Committee AGENCY: Missile... Advisory Committee Act of 1972 (5 U.S.C., Appendix, as amended) and the Government in the Sunshine Act of... Missile Defense Advisory Committee will meet on August 4 and 5, 2010, in Washington, DC. DATES: The...

  1. 75 FR 30002 - Federal Advisory Committee; Threat Reduction Advisory Committee

    Science.gov (United States)

    2010-05-28

    ... Office of the Secretary Federal Advisory Committee; Threat Reduction Advisory Committee AGENCY: Department of Defense (DoD). ACTION: Renewal of Federal advisory committee. SUMMARY: Under the provisions of the Federal Advisory Committee Act of 1972, (5 U.S.C. Appendix), the Government in the Sunshine Act of...

  2. 75 FR 9416 - Advisory Committee Information Hotline

    Science.gov (United States)

    2010-03-02

    ... BIOLOGICS EVALUATION AND RESEARCH Allergenic Products Advisory Committee 3014512388 Blood Products Advisory... Committee 3014512391 CENTER FOR DRUG EVALUATION AND RESEARCH Anesthetic and Life Support Drugs Advisory Committee 3014512529 Anti-Infective Drugs Advisory Committee 3014512530 Antiviral Drugs Advisory Committee...

  3. Public affairs committee actions

    Science.gov (United States)

    The AGU Public Affairs Committee will create an ad hoc committee to consider possible AGU position statements concerning the effects of nuclear war.The action was taken at the May 31, 1983, meeting of the Committee at the AGU Spring Meeting in Baltimore. Present were Carroll Ann Hodges, Chairman, and members Thomas J. Ahrens, David Cauffman, Jared Cohon, Stamatios Krimigis, Robert Murphy, Raymond Roble, and George Shaw. Also attending were the current Congressional Fellow Arthur Weissman and SPR—Cosmic Rays Section Secretary Miriam Forman.

  4. Influence of thermo-mechanical processing on the microstructure of Cu-based shape memory alloys produced by powder metallurgy

    International Nuclear Information System (INIS)

    Rodriguez, P.P.; Ibarra, A.; Iza-Mendia, A.; Recarte, V.; Perez-Landazabal, J.I.; San Juan, J.; No, M.L.

    2003-01-01

    Cu-Al-Ni shape memory alloys processed by powder metallurgy show very good thermo-mechanical properties, much better than those found in alloys produced by conventional casting. In this paper, we present the microstructural characterisation of these powder metallurgy alloys in order to find the microscopic mechanisms, linked to the powder metallurgy processing method, which are indeed responsible of such good thermo-mechanical behaviour. Electron microscopy studies [scanning electron microscopy (SEM), electron backscatter diffraction (EBSD) and transmission electron microscopy (TEM)] show that powder metallurgy processing creates a sub-grain structure characterised by the presence of low angle sub-boundaries. These sub-boundaries are found to be lying on {1 1 0} and {1 1 2} lattice planes and are composed by an arrangement of superdislocations. These sub-boundaries may improve ductility in two ways: acting as a sink of dislocations which promotes plastic deformation and decreasing stress concentration at grain boundaries. Moreover, since sub-boundaries act as weak obstacles for the movement of martensite plates, the improvement on ductility is accomplished by an adequate thermo-mechanical behaviour

  5. Physical metallurgy

    International Nuclear Information System (INIS)

    Adda, Y.; Dupouy, J.M.; Philibert, J.; Quere, S.

    1979-01-01

    This manual deals with the following subjects: plastic deformation of pure metals, yield strength in pure metals, work hardening in pure metals, hardening of solid solutions, recovery, recrystallization, crystal growth, creep, rupture and fatigue properties, metal transformations [fr

  6. Physical metallurgy

    International Nuclear Information System (INIS)

    Adda, Y.; Dupouy, J.M.; Philibert, J.; Quere, Y.

    1976-01-01

    In this manual, the following topics are discussed: thermodynamics of solid solutions, phase diagrams, properties of dilute solid solutions, structure of solid solutions, thermodynamics of surfaces, perfect dislocations, partial dislocations and stacking faults, interfaces, point defects

  7. Physical metallurgy

    International Nuclear Information System (INIS)

    Adda, Y.; Dupouy, J.M.; Philibert, J.; Quere, Y.

    1976-01-01

    In this manual the following topics are reviewed: macroscopic thermodynamics, statistical mechanics, quantum mechanics, cristallography, elasticity and anelasticity, and plastic deformation of a homogeneous medium [fr

  8. Physical metallurgy

    International Nuclear Information System (INIS)

    Adda, Y.; Dupouy, J.M.; Philibert, J.; Quere, Y.

    1976-01-01

    In this manual, the following topics are discussed: atomic vibrations, lattice thermal properties, chemical bonds, free electron model, band theory, properties of actinides, rare earths and transition metals, transport phenomena, magnetic properties, properties of liquid metals and amorphous state alloys

  9. Practical Metallurgy

    DEFF Research Database (Denmark)

    Bissacco, Giuliano; Deganello, Davide

    2003-01-01

    This is the report regards the activities carried out during the practical metatllurgy course concerning material properties and structures and their testing & analysis methods. During the course several aspects of the materials have been considered and different techniques have been analyzed....

  10. Summary reports of the R and D programme: recycling of non-ferrous metals (1986-1989)

    International Nuclear Information System (INIS)

    Donato, M.

    1992-01-01

    This document contains the summary reports of cost sharing research and development contracts funded under the recycling of non-ferrous metals subprogramme of the Commission of the European Communities. In particular from p.171 to 212 is described the recovery of rare earths by supported liquid membranes: synthesis and use of new selective macrocyclic and/or compartmental ligands

  11. Arsenic Encapsulation Using Portland Cement With Ferrous Sulfate/Lime And Terra-BondTM Technologies - Microcharacterization And Leaching Studies

    Science.gov (United States)

    This work reports the results of an investigation on the treatment and encapsulation of arsenic-containing materials by Portland cement with ferrous sulfate and lime (PFL) and Terra-BondTM, a commercially available patented technology. The arsenic materials treated we...

  12. Were mercury emission factors for Chinese non-ferrous metal smelters overestimated? Evidence from onsite measurements in six smelters

    International Nuclear Information System (INIS)

    Zhang Lei; Wang Shuxiao; Wu Qingru; Meng Yang; Yang Hai; Wang Fengyang; Hao Jiming

    2012-01-01

    Non-ferrous metal smelting takes up a large proportion of the anthropogenic mercury emission inventory in China. Zinc, lead and copper smelting are three leading sources. Onsite measurements of mercury emissions were conducted for six smelters. The mercury emission factors were 0.09–2.98 g Hg/t metal produced. Acid plants with the double-conversion double-absorption process had mercury removal efficiency of over 99%. In the flue gas after acid plants, 45–88% was oxidized mercury which can be easily scavenged in the flue gas scrubber. 70–97% of the mercury was removed from the flue gas to the waste water and 1–17% to the sulfuric acid product. Totally 0.3–13.5% of the mercury in the metal concentrate was emitted to the atmosphere. Therefore, acid plants in non-ferrous metal smelters have significant co-benefit on mercury removal, and the mercury emission factors from Chinese non-ferrous metal smelters were probably overestimated in previous studies. - Highlights: ► Acid plants in smelters provide significant co-benefits for mercury removal (over 99%). ► Most of the mercury in metal concentrates for smelting ended up in waste water. ► Previously published emission factors for Chinese metal smelters were probably overestimated. - Acid plants in smelters have high mercury removal efficiency, and thus mercury emission factors for Chinese non-ferrous metal smelters were probably overestimated.

  13. MRI staging of urinary bladder cancer: results using a ferrous contrastographic solution (JKA1)

    International Nuclear Information System (INIS)

    Giovagnoli, A.; Ercolani, P.; De Nigris, E.; Villanova, A.

    1990-01-01

    The authors report the results of the staging of urinary bladder cancers by means of MRI using a new ferrous contrastographic solution called JKA1. Eighteen patients with proved bladder neoplasms were examined by means of MRI: the bladder was filled with physiological solution first, and then with JKA1. Six patients were studied also after filling their bladders with Gd DTPA solution (1:50). The results show that the use of JKA1, a T2-positive contrast medium, improved MR capabilities in the evaluation of small lesions (<1cm in diameter) with minimal invasion of bladder wall; MR staging accuracy was 66.6% with the physiological solution and 77.8% with JKA1. The authors confirm the need for a wider MR study, in particular of T2 lesions (a critical subject for staging and surgical management) to assess MR diagnostic capabilities

  14. Reaction of the H atom in gamma-irradiated ferrous sulphate solutions

    International Nuclear Information System (INIS)

    Mathews, R.W.

    1977-10-01

    The effect of sulphuric acid, ferrous and ferric ion, and oxygen concentrations on G(Fe 3+ ) values from cobalt-60 gamma-irradiated soltuions has been studied. Kinetic expressions were derived for reaction models involving reactions of various forms of the H atom and additional reactions postulated to be of importance at high solute concentration. Three models were assumed invoking the additional reactions: (1) an independent yield of an excited water species; (2) increasing contributions from interspur reactions of well established species at increasing solute concentration; (3) inhibition of charge pair recombination by acid and scavenger species. The calculated G(Fe 3+ ) values from the various models were compared by the least squares method with experimental G(Fe 3+ ) values from over 600 irradiations. Model 3 provided the best fit to the data for the least number of adjustable parameters. No evidence for more than one form of H atom was found with this model. (J.R.)

  15. Magnetic hyperthermia heating of cobalt ferrite nanoparticles prepared by low temperature ferrous sulfate based method

    Directory of Open Access Journals (Sweden)

    Tejabhiram Yadavalli

    2016-05-01

    Full Text Available A facile low temperature co-precipitation method for the synthesis of crystalline cobalt ferrite nanostructures using ferrous sulfate salt as the precursor has been discussed. The prepared samples were compared with nanoparticles prepared by conventional co-precipitation and hydrothermal methods using ferric nitrate as the precursor. X-ray diffraction studies confirmed the formation of cubic spinel cobalt ferrites when dried at 110 °C as opposed to conventional methods which required higher temperatures/pressure for the formation of the same. Field emission scanning electron microscope studies of these powders revealed the formation of nearly spherical nanostructures in the size range of 20-30 nm which were comparable to those prepared by conventional methods. Magnetic measurements confirmed the ferromagnetic nature of the cobalt ferrites with low magnetic remanance. Further magnetic hyperthermia studies of nanostructures prepared by low temperature method showed a rise in temperature to 50 °C in 600 s.

  16. Reversibility in martensitic transformation and shape memory in high Mn ferrous alloys

    International Nuclear Information System (INIS)

    Tomota, Y.

    2000-01-01

    The reversibility of austenite (γ : fcc) epsilon (ε : hcp) martensitic transformation and shape memory effect in high Mn ferrous alloys are discussed. A particular emphasis is put on the ε → γ reverse transformation behavior in two poly-crystalline alloys, Fe-24Mn and Fe-24Mn-6Si, where the latter exhibits excellent shape memory while the former shows poor memory although their forward γ → ε transformation behavior is quite similar. TEM in situ observations have revealed that the motion of Shockley partial dislocations during ε → γ reverse transformation is different from each other in these two alloys. The influence of alloying elements on the shape memory effect can be related to solid solution hardening of austenite, suggesting an important role of internal stress. The effect of training on enhancing the shape memory is explained by such an internal stress distribution associated with the formation of very thin, i.e., nano-scale ε/γ lamellae. (orig.)

  17. Evaluation of commercial grade ferrous ammonium sulfate as potential dosimeter for technological irradiations

    International Nuclear Information System (INIS)

    Juarez-Calderon, J. Manuel; Ramos-Bernal, Sergio; Negron-Mendoza, Alicia

    2008-01-01

    In this work, we have studied the behavior of crystalline ferrous ammonium sulfate (FAS) under gamma irradiation. The doses studied ranged from 33.5 to 270 kGy. The purpose of this study is to explain the setup, measurement, and reporting procedures for using FAS as a dosimeter. The results obtained in the present study show that this salt very easily gave reproducible results, a linear response, as well as, simple sample preparation and reading. The irradiation temperature and dose rate in the response of the iron salt were found to have slight influence. Any storage time up to 18 months resulted in a 36% decreased in the response. The variation in the response obtained for short periods of storage is negligible for this application. Due to the properties of the FAS system also can be use as transfer dosimeter. (author)

  18. Hepatoprotective potential of Azima tetracantha and Tribulus terrestris on ferrous sulfate-induced toxicity in rat

    Directory of Open Access Journals (Sweden)

    Manikandaselvi Sambasivam

    2013-08-01

    Full Text Available The present study is to evaluate the antihepatotoxic effect of hydroalcoholic extract of leaf powder of Azima tetracantha and the fruit powder of Tribulus terrestris. Ferrous sulfate was used to induce hepatotoxicity and Silymarin was used as a standard drug. The level of biochemical parameters such as protein, albumin, globulin, HDL, vitamin E, superoxide dismutase and catalase were observed to be decreased and the level of glucose, LDL, VLDL, bilirubin, cholesterol, triglycerides, alkaline phosphatase and TBARS were increased in hepatotoxicity-induced rats. Retrieval of liver parameters to normal level was obtained after the oral administration of herbal drugs. Histopathological studies revealed diminished hepatocellular injury in the herbal drugs treated rats. As a conclusion hydro alcoholic extract of leaf powder of A. tetracantha and fruit powder of T. terrestris were possesses significant hepatoprotective activity.

  19. Standing Concertation Committee

    CERN Multimedia

    HR Department

    2010-01-01

    Main issues examined at the meeting of 2 October 2009 The October 2009 meeting of the Standing Concertation Committee was entirely devoted to preparation of TREF’s meeting on 21-22 October. The Committee took note of, discussed and agreed on clarifications needed to some of the documents and presentations that the Management intended to submit and/or present to TREF on the following subjects: Equal opportunities The Committee took note of a preliminary report on equal opportunities at CERN drawn up by D. Chromek-Burckhart, the Equal Opportunities Officer, and T. Smith, Chairman of the Equal Opportunities Advisory Panel, containing in particular a proposal for a new process for resolving harassment conflicts. Technical analysis of the CERN Health Insurance Scheme - Actuary’s Report The Committee took note of a presentation by P. Charpentier, Chairman of the CERN Health Insurance Supervisory Board (CHIS Board), on the 2009 actuarial report on the CERN Health Insurance Scheme (CHIS). Th...

  20. Standing Concertation Committee

    CERN Multimedia

    HR Department

    2008-01-01

    ORDINARY MEETING ON 27 FEBRUARY 2008 The main items discussed at the meetings of the Standing Concertation Committee on 27 February 2008 included: Short-term Saved Leave Scheme The Committee noted that, by the end of February 2008, some 600 staff had enrolled in the short-term saved leave scheme: approx. 58% had signed up for 1 slice, 14% for two slices, 5% for three slices and 23% for four slices. Administrative Circular No. 4 (Rev. 4) - Unemployment Insurance Scheme The Committee agreed to recommend the Director-General to approve Administrative Circular No. 4 (Rev. 4) - Unemployment Insurance Scheme. Administrative Circular No. 30 (Rev. 2) - Financial benefits upon taking up appointment and termination of contract The Committee agreed to recommend the Director-General to approve Administrative Circular No. 30 (Rev. 2) - Financial Benefits upon taking up appointment and termination of contract. Progressive Retirement Programme The Progressive Retirement Programme (PR...

  1. Mathematical Modelling of the Price Range in the Procurement of Ferrous Scrap by Metallurgical Enterprises

    Directory of Open Access Journals (Sweden)

    Tatyana Aleksandrovna Ivanova

    2018-03-01

    Full Text Available For metallurgical enterprises, it is important to understand the limits of the most probable values of prices and geographical area for procurement of ferrous scrap in the regions. In order to define the maximal scrap prices in the regions, the authors have developed a mathematical model of “auction purchases”. This model equally assesses price competition between scrap consumers. When setting the price, we consider the territorial imbalances between scrap supply and demand in the regions; costs for scrap transportation from supplier to consumer; price level for scrap in the “windows for exports”. We calculate the lowest price according to the “export parity”. The results of the calculations allow evaluating a range of regional prices and interregional flows of scrap. This approach is unnown in the published works of Russian and foreign researchers. For calculations, we have developed a special software. The following initial data were used: data on railroad transportation of ferrous scrap in the Russian Federation provided by JSC Russian Railways; handbooks of railway tariffs 10–01 between railway stations of the Russian Federation; statistical data on prices of 3A metal scrap in the “windows for exports”. The article presents the formal structure of the model of “auction procurement”, the algorithm of its implementation and the results of calculations. The price level calculated according to the model of “auction procurement” can be used in management practice as potentially highest level of price, which can be reached in the conditions of competition between consumers of scrap in a situation when the negotiations are impossible. The proposed mathematical model allows a metallurgical enterprise to prove and implement a differentiated approach to the formation of regional prices of scrap, and to define regions for scrap purchasing.

  2. Aspects of the magnetism of ferrous chloride; Aspects du magnetisme du chlorure ferreux

    Energy Technology Data Exchange (ETDEWEB)

    Carrara, P. [Commissariat a l' Energie Atomique Saclay (France). Centre d' Etudes Nucleaires

    1968-03-01

    This work is a critical review of the existing work on ferrous chloride and presents, as well, a number of new experimental results. First, a careful analysis of the level structure of ferrous ions in the crystalline field shows that the crystalline anisotropy is of the same order of magnitude as the exchange interactions, a feature which gives rise to some particular effects, such as an upward curvature of the magnetization curve at 0 K in a perpendicular magnetic field. Further, the very low temperature (T > 0.4 K) thermal variation of both the specific heat and magnetic susceptibility evidences a magnetic component in elementary excitations. This result suggests the presence of a large magneto-elastic coupling. Finally, an experimental study of the H-T phase diagram near T{sub N} and of the critical behaviour of the specific heat and parallel susceptibility was performed. (author) [French] Ce travail constitue une analyse critique des resultats obtenus a ce jour sur le chlorure ferreux et comporte en outre quelques resultats experimentaux nouveaux. Tout d'abord, une etude precise de la structure de niveaux de l'ion ferreux dans le champ cristallin montre que l'anisotropie cristalline est comparable aux interactions d'echange, ce qui produit quelques effets originaux tels que, par exemple, l'inflexion de la courbe d'aimantation a 0 K en champ perpendiculaire. D'autre part, la variation thermique a basse temperature (T > 0.4 K) de la chaleur specifique et de la susceptibilite magnetique montre la presence d'une composante magnetique dans les excitations de basse energie. Ce resultat suggere la presence d'un couplage magneto-elastique. Enfin, nous avons realise une etude experimentale de la ligne de transition de phase (diagramme H,T) au voisinage de T{sub N}, et du comportement critique de la chaleur specifique et de la susceptibilite parallele. (auteur)

  3. Active removal of ibuprofen by Money plant enhanced by ferrous ions.

    Science.gov (United States)

    Chehrenegar, Behdad; Hu, Jiangyong; Ong, Say Leong

    2016-02-01

    In this study, the removal of ibuprofen (IBP), a pharmaceutical compound, from aqueous media by Money plant (Epipremnum aureum) was investigated. The effect of ferrous iron (Fe(2+)) on enhancing the IBP removal rate was also analyzed. The first-order removal rate constants showed higher values for lower IBP initial concentrations in the range of 0.20-0.28 d(-1) for an initial concentration of 125 μg L(-1) to 0.03-0.13 d(-1) for an initial concentration of 1000 μg L(-1). Introducing ferrous iron to the aqueous media enhanced the first-order removal rate constant up to 6.5 times in a 3 d time period. Along with the removal of IBP from the media, the endogenous concentration of H2O2 also decreased presumably by the production of hydroxyl radical (·OH). Reduction in the endogenous H2O2 concentration was recorded to be 38% and 98% in the absence and presence of Fe(2+) respectively in the first day and the H2O2 level remained considerably low until day 7 which then gradually increased slightly. Simultaneous reduction of IBP and endogenous H2O2 concentration could be due to the reaction of IBP with ·OH and presumably ·OH production itself accelerated via Fenton reaction. In addition, presence of sodium bicarbonate (NaHCO3) as ·OH scavenger in the system showed reduction of first-order removal rate constant from 1.30 d(-1) to 0.07 d(-1) which could be a possible evidence of biological advanced oxidation process which is believed to play an important role in phytoremediation. Copyright © 2015 Elsevier Ltd. All rights reserved.

  4. Ferrous-activated persulfate oxidation of arsenic(III) and diuron in aquatic system.

    Science.gov (United States)

    Zhou, Lei; Zheng, Wei; Ji, Yuefei; Zhang, Jinfeng; Zeng, Chao; Zhang, Ya; Wang, Qi; Yang, Xi

    2013-12-15

    In situ chemical oxidation (ISCO) can be an effective technology for the remediation of soil and groundwater polluted by organic and inorganic contaminants. This study investigated the oxidation of arsenic(III) (As(III)) and diuron using ferrous activated persulfate-based ISCO. The results indicated that Fe(II)/persulfate oxidation could be an effective method to oxidize As(III) and diuron. Effects of pH, S2O8(2-) and Fe(II) amounts on the destruction of As(III) and diuron were examined in batch experiments. Acidic conditions favored the removal of As(III) and diuron. Four chelating agents, citric acid (CA), Na2S2O3, diethylene triamine pentaacetic acid (DTPA) and ethylene diamine tetraacetic acid disodium (EDTA-Na2) were used in attempt to maintain the quantity of ferrous ion in solution. In our experiments, CA and Na2S2O3 were found to be more effective than DTPA and EDTA-Na2. Our results also revealed a widely practical prospect of inorganic chelating agent Na2S2O3. Hydroxyl and sulfate radical were determined to play key roles in the oxidation process by using ethanol and tertiary butanol as molecular probes. Oxidation of As(III) yielded As(V) via the electron-transfer reaction. In the oxidation process of diuron, a stepwise nucleophilic substitution of chlorine by hydroxyl and a stepwise oxidation process of the methyl on the dimethylurea group by hydroxyl and sulfate radical were proposed. Copyright © 2013 Elsevier B.V. All rights reserved.

  5. Ferrous-activated persulfate oxidation of arsenic(III) and diuron in aquatic system

    International Nuclear Information System (INIS)

    Zhou, Lei; Zheng, Wei; Ji, Yuefei; Zhang, Jinfeng; Zeng, Chao; Zhang, Ya; Wang, Qi; Yang, Xi

    2013-01-01

    Highlights: • Effective oxidation of As(III)/diuron is achieved by Fe(II)-activated persulfate. • Hydroxyl and sulfate radical play important roles in As(III) and diuron oxidation. • CA and Na 2 S 2 O 3 are efficient and environmental friendly chelating agents. • DFT calculation is found to be useful for degradation products prediction. -- Abstract: In situ chemical oxidation (ISCO) can be an effective technology for the remediation of soil and groundwater polluted by organic and inorganic contaminants. This study investigated the oxidation of arsenic(III) (As(III)) and diuron using ferrous activated persulfate-based ISCO. The results indicated that Fe(II)/persulfate oxidation could be an effective method to oxidize As(III) and diuron. Effects of pH, S 2 O 8 2− and Fe(II) amounts on the destruction of As(III) and diuron were examined in batch experiments. Acidic conditions favored the removal of As(III) and diuron. Four chelating agents, citric acid (CA), Na 2 S 2 O 3 , diethylene triamine pentaacetic acid (DTPA) and ethylene diamine tetraacetic acid disodium (EDTA-Na 2 ) were used in attempt to maintain the quantity of ferrous ion in solution. In our experiments, CA and Na 2 S 2 O 3 were found to be more effective than DTPA and EDTA-Na 2 . Our results also revealed a widely practical prospect of inorganic chelating agent Na 2 S 2 O 3 . Hydroxyl and sulfate radical were determined to play key roles in the oxidation process by using ethanol and tertiary butanol as molecular probes. Oxidation of As(III) yielded As(V) via the electron-transfer reaction. In the oxidation process of diuron, a stepwise nucleophilic substitution of chlorine by hydroxyl and a stepwise oxidation process of the methyl on the dimethylurea group by hydroxyl and sulfate radical were proposed

  6. Inhibition of bacterial oxidation of ferrous iron by lead nitrate in sulfate-rich systems

    Science.gov (United States)

    Wang, Hongmei; Gong, Linfeng; Cravotta,, Charles A.; Yang, Xiaofen; Tuovinen, Olli H.; Dong, Hailiang; Fu, Xiang

    2013-01-01

    Inhibition of bacterial oxidation of ferrous iron (Fe(II)) by Pb(NO3)2 was investigated with a mixed culture of Acidithiobacillus ferrooxidans. The culture was incubated at 30 °C in ferrous-sulfate medium amended with 0–24.2 mM Pb(II) added as Pb(NO3)2. Anglesite (PbSO4) precipitated immediately upon Pb addition and was the only solid phase detected in the abiotic controls. Both anglesite and jarosite (KFe3(SO4)2(OH)6) were detected in inoculated cultures. Precipitation of anglesite maintained dissolved Pb concentrations at 16.9–17.6 μM regardless of the concentrations of Pb(NO3)2 added. Fe(II) oxidation was suppressed by 24.2 mM Pb(NO3)2 addition even when anglesite was removed before inoculation. Experiments with 0–48 mM KNO3 demonstrated that bacterial Fe(II) oxidation decreased as nitrate concentration increased. Therefore, inhibition of Fe(II) oxidation at 24.2 mM Pb(NO3)2 addition resulted from nitrate toxicity instead of Pb addition. Geochemical modeling that considered the initial precipitation of anglesite to equilibrium followed by progressive oxidation of Fe(II) and the precipitation of jarosite and an amorphous iron hydroxide phase, without allowing plumbojarosite to precipitate were consistent with the experimental time-series data on Fe(II) oxidation under biotic conditions. Anglesite precipitation in mine tailings and other sulfate-rich systems maintains dissolved Pb concentrations below the toxicity threshold of A. ferrooxidans.

  7. Overview of the long distance iron ore slurry pipeline from Anglo Ferrous Brazil

    Energy Technology Data Exchange (ETDEWEB)

    Silva, Adarlan M.; Passos, Aline C.; Santos, Daniel; Orban, Eduardo M.; Lisboa, Helder D.; Goncalves, Nilton; Guimaraes, Robson C. [Anglo Ferrous Brazil, Rio de Janeiro, RJ (Brazil)

    2009-07-01

    The objective of this paper is to present an overview of the long distance iron ore slurry pipeline from Anglo Ferrous Brazil. Anglo Ferrous Brazil is a company of Anglo American plc that is one of the world's largest mining and natural resource company. Minas-Rio is a world class iron ore project which has been developed in Brazil aiming to produce 26.6 million tons per year of concentrate. The mine, concentrator and pump station 1 will be located in Conceicao do Mato Dentro, Minas Gerais state, and the terminal station will be located at Acu Port in Sao Joao da Barra, Rio de Janeiro state. The long distance iron ore slurry pipeline will be one of major differentials of Minas-Rio Project and its useful life was initially estimated in 20 years. The slurry pipeline has a total length of 525 kilometers and will be constructed from predominately 26 inches external diameter API 5L X70 pipes. From kilometer 314 to kilometer 480, 24 inches pipe will be installed to prevent slack flow downstream pump station 2. The pump station 1 is designed to provide the hydraulic head necessary to transport the concentrate iron ore slurry with 8 positive displacement pumps to pump station 2. The pump station 2, located 240 kilometers downstream pump station 1, is designed to operate with 10 positive displacement pumps. The valve station will be located at kilometer 347 and will be used to break the static head between pump station 2 and the terminal station during a slurry pipeline shutdown. (author)

  8. German experience in recycling of ferrous metallic residues from nuclear decommissioning by melting

    International Nuclear Information System (INIS)

    Quade, U.; Kluth, Th.

    2008-01-01

    Due to the delay of commissioning of final depositories for nuclear waste on the one hand and the increasing amount of steel scrap resulting from operation and decommissioning of nuclear facilities on the other hand, recycling of ferrous metal scrap to packagings made of ductile cast iron becomes more and more economical. A pool of know-how from waste managers, radiation protection experts, metallurgists and foundry experts and their teamwork is required to run this recycling path successfully. Siempelkamp provides this combination of experience by operating a melting facility for slightly radioactive contaminated scrap as well as a foundry for manufacturing of ductile cast iron products for the nuclear industry, both licensed by the German Radiation Protection Ordinance. In 1989, the CARLA plant (Centrale Anlage zum Rezyklieren von leichtradioaktiven Abfollen) started operation. A medium frequency induction furnace with a capacity of 3,2 t is core of the plant. Tools for dismantling and cutting components to chargeable sizes are available. From the total of 23000 t of melted scrap, 12000 t have been recycled to the manufacturing of containers for transport and storage of medium- and high active waste and for shielding plates. Manufacture of the castings takes place in the Siempelkamp foundry located at the same site. 8000 t of melted scrap could be released for industrial recycling. Scrap metal which does not meet the metallurgical specification for cast iron, is converted into iron granules. Up to now more than 2000 t of iron granules have been recycled as additive for heavy concrete containers. This production is in cooperation with an external partner. With regard to the German situation, the cost for recycling is only half compared to high pressure compaction, long-term interim storage and final disposal. The advantage of recycling is approx. 90 % less volume compared to the volume resulting from other disposal paths. It can be concluded that the German

  9. A Metallurgical Investigation of the Direct Energy Deposition Surface Repair of Ferrous Alloys

    Science.gov (United States)

    Marya, Manuel; Singh, Virendra; Hascoet, Jean-Yves; Marya, Surendar

    2018-02-01

    Among additive manufacturing (AM) processes, the direct energy deposition (DED) by laser is explored to establish its applicability for the repair of ferrous alloys such as UNS G41400 low-alloy steel, UNS S41000 martensitic stainless steel, UNS S17400 precipitation-strengthened martensitic stainless steel, and UNS S32750 super-duplex stainless steel. Unlike plating, thermal spray, and conventional cladding weld, DED laser powder deposition offers potential advantages, e.g., thin deposits, limited dilutions, narrow heat-affected zones (HAZ), potentially improved surface properties. In this investigation, all AM deposits were completed with an IREPA CLAD™ system using a powder feed of UNS N06625, an alloy largely selected for its outstanding corrosion resistance. This investigation first addresses topological aspects of AM deposits (including visual imperfections) before focusing on changes in microstructure, microhardness, chemical composition across AM deposits and base materials. It has been established that dense, uniform, hard ( 300 HVN), crack-free UNS N06625-compliant AM deposits of fine dendritic microstructures are reliably produced. However, except for the UNS S32750 steel, a significant martensitic hardening was observed in the HAZs of UNS G41400 ( 650 HVN), UNS S41000 ( 500 HVN), and UNS S17400 ( 370 HVN). In summary, this investigation demonstrates that the DED laser repair of ferrous parts with UNS N06625 may restore damaged surfaces, but it also calls for cautions and complementary investigations for alloys experiencing a high HAZ hardening, for which industry standard recommendations are exceeded and lead to an increased risk of delayed cracking in corrosive environments.

  10. Monomer-dimer equilibrium and oxygen binding properties of ferrous Vitreoscilla hemoglobin.

    Science.gov (United States)

    Giangiacomo, L; Mattu, M; Arcovito, A; Bellenchi, G; Bolognesi, M; Ascenzi, P; Boffi, A

    2001-08-07

    The monomer-dimer equilibrium and the oxygen binding properties of ferrous recombinant Vitreoscilla hemoglobin (Vitreoscilla Hb) have been investigated. Sedimentation equilibrium data indicate that the ferrous deoxygenated and carbonylated derivatives display low values of equilibrium dimerization constants, 6 x 10(2) and 1 x 10(2) M(-1), respectively, at pH 7.0 and 10 degrees C. The behavior of the oxygenated species, as measured in sedimentation velocity experiments, is superimposable to that of the carbonylated derivative. The kinetics of O(2) combination, measured by laser photolysis at pH 7.0 and 20 degrees C, is characterized by a second-order rate constant of 2 x 10(8) M(-1) s(-1) whereas the kinetics of O(2) release at pH 7.0 is biphasic between 10 and 40 degrees C, becoming essentially monophasic below 10 degrees C. Values of the first-order rate constants (at 20 degrees C) and of the activation energies for the fast and slow phases of the Vitreoscilla Hb deoxygenation process are 4.2 s(-1) and 19.2 kcal mol(-1) and 0.15 s(-1) and 24.8 kcal mol(-1), respectively. Thus the biphasic kinetics of Vitreoscilla Hb deoxygenation is unrelated to the association state of the protein. The observed biphasic oxygen release may be accounted for by the presence of two different conformers in thermal equilibrium within the monomer. The two conformers may be assigned to a structure in which the heme-iron-bound ligand is stabilized by direct hydrogen bonding to TyrB10 and a structure in which such interaction is absent. The slow interconversion between the two conformers may reflect a very large conformational rearrangement in the disordered distal pocket segment connecting helices C and E.

  11. Evaluation of effects of Maṇḍurabhasma on structural and functional integrity of small intestine in comparison with ferrous sulfate using an experimental model of iron deficiency anemia

    Directory of Open Access Journals (Sweden)

    Suchita Rajanikant Gawde

    2015-01-01

    Conclusion: Rats receiving a high dose of MB have shown improvement in hematinic and lactase levels comparable to those receiving ferrous sulfate. However, it causes lesser oxidative damage as compared to ferrous sulfate. This is an encouraging finding because it indicates the potential of MB to cause lesser gastrointestinal side effects compared to ferrous sulfate.

  12. Application of Microscopy and X-ray Diffraction in Optimization of the Production of NiTi Alloy by Powder Metallurgy

    Czech Academy of Sciences Publication Activity Database

    Novák, P.; Školáková, A.; Vojtěch, V.; Knaislová, A.; Pokorný, P.; Moravec, H.; Kopeček, Jaromír; Karlík, M.; Kubatík, Tomáš František

    2014-01-01

    Roč. 14, č. 3 (2014), s. 387-392 ISSN 1213-2489. [Mezinárodní konference „Mikroskopie a nedestruktivní zkoušení materiálů/3./. Litoměřice, 22.10.2014-24.10.2014] R&D Projects: GA ČR(CZ) GA14-03044S Institutional support: RVO:61389021 ; RVO:68378271 Keywords : powder metallurgy * NiTi, * mechanical alloying * reactive sintering Subject RIV: JG - Metallurgy; JG - Metallurgy (FZU-D) http://journal.strojirenskatechnologie.cz/templates/obalky_casopis/XIV_2014-3.pdf

  13. Ferrous sulfate supplementation causes significant gastrointestinal side-effects in adults: a systematic review and meta-analysis.

    Directory of Open Access Journals (Sweden)

    Zoe Tolkien

    Full Text Available The tolerability of oral iron supplementation for the treatment of iron deficiency anemia is disputed.Our aim was to quantify the odds of GI side-effects in adults related to current gold standard oral iron therapy, namely ferrous sulfate.Systematic review and meta-analysis of randomized controlled trials (RCTs evaluating GI side-effects that included ferrous sulfate and a comparator that was either placebo or intravenous (i.v. iron. Random effects meta-analysis modelling was undertaken and study heterogeneity was summarised using I2 statistics.Forty three trials comprising 6831 adult participants were included. Twenty trials (n = 3168 had a placebo arm and twenty three trials (n = 3663 had an active comparator arm of i.v. iron. Ferrous sulfate supplementation significantly increased risk of GI side-effects versus placebo with an odds ratio (OR of 2.32 [95% CI 1.74-3.08, p<0.0001, I2 = 53.6%] and versus i.v. iron with an OR of 3.05 [95% CI 2.07-4.48, p<0.0001, I2 = 41.6%]. Subgroup analysis in IBD patients showed a similar effect versus i.v. iron (OR = 3.14, 95% CI 1.34-7.36, p = 0.008, I2 = 0%. Likewise, subgroup analysis of pooled data from 7 RCTs in pregnant women (n = 1028 showed a statistically significant increased risk of GI side-effects for ferrous sulfate although there was marked heterogeneity in the data (OR = 3.33, 95% CI 1.19-9.28, p = 0.02, I2 = 66.1%. Meta-regression did not provide significant evidence of an association between the study OR and the iron dose.Our meta-analysis confirms that ferrous sulfate is associated with a significant increase in gastrointestinal-specific side-effects but does not find a relationship with dose.

  14. Ferrous sulfate supplementation causes significant gastrointestinal side-effects in adults: a systematic review and meta-analysis.

    Science.gov (United States)

    Tolkien, Zoe; Stecher, Lynne; Mander, Adrian P; Pereira, Dora I A; Powell, Jonathan J

    2015-01-01

    The tolerability of oral iron supplementation for the treatment of iron deficiency anemia is disputed. Our aim was to quantify the odds of GI side-effects in adults related to current gold standard oral iron therapy, namely ferrous sulfate. Systematic review and meta-analysis of randomized controlled trials (RCTs) evaluating GI side-effects that included ferrous sulfate and a comparator that was either placebo or intravenous (i.v.) iron. Random effects meta-analysis modelling was undertaken and study heterogeneity was summarised using I2 statistics. Forty three trials comprising 6831 adult participants were included. Twenty trials (n = 3168) had a placebo arm and twenty three trials (n = 3663) had an active comparator arm of i.v. iron. Ferrous sulfate supplementation significantly increased risk of GI side-effects versus placebo with an odds ratio (OR) of 2.32 [95% CI 1.74-3.08, p<0.0001, I2 = 53.6%] and versus i.v. iron with an OR of 3.05 [95% CI 2.07-4.48, p<0.0001, I2 = 41.6%]. Subgroup analysis in IBD patients showed a similar effect versus i.v. iron (OR = 3.14, 95% CI 1.34-7.36, p = 0.008, I2 = 0%). Likewise, subgroup analysis of pooled data from 7 RCTs in pregnant women (n = 1028) showed a statistically significant increased risk of GI side-effects for ferrous sulfate although there was marked heterogeneity in the data (OR = 3.33, 95% CI 1.19-9.28, p = 0.02, I2 = 66.1%). Meta-regression did not provide significant evidence of an association between the study OR and the iron dose. Our meta-analysis confirms that ferrous sulfate is associated with a significant increase in gastrointestinal-specific side-effects but does not find a relationship with dose.

  15. Some aspects of barreling in sintered plain carbon steel powder metallurgy preforms during cold upsetting

    Directory of Open Access Journals (Sweden)

    Sumesh Narayan

    2012-04-01

    Full Text Available The present research establishes a relationship of bulged diameter with densification and hydrostatic stress in forming of sintered iron (Fe powder metallurgy preforms cold upset under two different frictional conditions, namely, nil/no and graphite lubricant condition. Sintered plain carbon steel cylindrical preforms with carbon (C contents of 0, 0.35, 0.75 and 1.1% with constant initial theoretical density of 84% and aspect ratio of 0.4 and 0.6 were prepared using a suitable die-set assembly on a 1 MN capacity hydraulic press and sintered for 90 minutes at 1200 °C. Each sintered preform was cold upset under two different frictional constraints. It is seen that the degree of bulging reduces with reducing frictional constraints at the die contact surface. Further, it is found that the bulging ratio changed as a function of relative density and hydrostatic stress, respectively, according to the power law equations.

  16. Modeling of wear behavior of Al/B{sub 4}C composites produced by powder metallurgy

    Energy Technology Data Exchange (ETDEWEB)

    Sahin, Ismail; Bektas, Asli [Gazi Univ., Ankara (Turkey). Dept. of Industrial Design Engineering; Guel, Ferhat; Cinci, Hanifi [Gazi Univ., Ankara (Turkey). Dept. of Materials and Metallurgy Engineering

    2017-06-01

    Wear characteristics of composites, Al matrix reinforced with B{sub 4}C particles percentages of 5, 10,15 and 20 produced by the powder metallurgy method were studied in this study. For this purpose, a mixture of Al and B{sub 4}C powders were pressed under 650 MPa pressure and then sintered at 635 C. The analysis of hardness, density and microstructure was performed. The produced samples were worn using a pin-on-disk abrasion device under 10, 20 and 30 N load through 500, 800 and 1200 mesh SiC abrasive papers. The obtained wear values were implemented in an artificial neural network (ANN) model having three inputs and one output using feed forward backpropagation Levenberg-Marquardt algorithm. Thus, the optimum wear conditions and hardness values were determined.

  17. Modeling of wear behavior of Al/B4C composites produced by powder metallurgy

    International Nuclear Information System (INIS)

    Sahin, Ismail; Bektas, Asli; Guel, Ferhat; Cinci, Hanifi

    2017-01-01

    Wear characteristics of composites, Al matrix reinforced with B 4 C particles percentages of 5, 10,15 and 20 produced by the powder metallurgy method were studied in this study. For this purpose, a mixture of Al and B 4 C powders were pressed under 650 MPa pressure and then sintered at 635 C. The analysis of hardness, density and microstructure was performed. The produced samples were worn using a pin-on-disk abrasion device under 10, 20 and 30 N load through 500, 800 and 1200 mesh SiC abrasive papers. The obtained wear values were implemented in an artificial neural network (ANN) model having three inputs and one output using feed forward backpropagation Levenberg-Marquardt algorithm. Thus, the optimum wear conditions and hardness values were determined.

  18. Microstructure and microanalysis studies of copper-nickel-tin alloys obtained by conventional powder metallurgy processing

    Energy Technology Data Exchange (ETDEWEB)

    Monteiro, Waldemar A.; Carrio, Juan A.G.; Masson, T.J.; Vitor, E.; Abreu, C.D.; Marques, I.M., E-mail: fisica.cch@mackenzie.br [Universidade Presbiteriana Mackenzie (CCH), Sao Paulo, SP (Brazil). Centro de Ciencias e Humanidades; Silva, L.C.E. da, E-mail: jgcarrio@mackenzie.br [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

    2009-07-01

    The aim of this paper was to analyze the microstructural development in samples of Cu-Ni-Sn alloys (weight %) obtained by powder metallurgy (P/M). The powders were mixed for 1/2 hour. After this, they were pressed, in a cold uniaxial pressing (1000 kPa). In the next step the specimens were sintered at temperatures varying from 650 up to 780 deg C under vacuum. Secondly, the samples were homogenized at 500 deg C for several special times. The alloys were characterized by optical microscopy, electrical conductivity and Vickers hardness. X-rays powder diffraction data were collected for the sintered samples in order to a structural and microstructural analysis. The comparative analysis is based on the sintered density, densification parameter, hardness, macrostructures and microstructures of the samples. (author)

  19. A powder metallurgy austenitic stainless steel for application at very low temperatures

    CERN Document Server

    Sgobba, Stefano; Liimatainen, J; Kumpula, M

    2000-01-01

    The Large Hadron Collider to be built at CERN will require 1232 superconducting dipole magnets operating at 1.9 K. By virtue of their mechanical properties, weldability and improved austenite stability, nitrogen enriched austenitic stainless steels have been chosen as the material for several of the structural components of these magnets. Powder Metallurgy (PM) could represent an attractive production technique for components of complex shape for which dimension tolerances, dimensional stability, weldability are key issues during fabrication, and mechanical properties, ductility and leak tightness have to be guaranteed during operation. PM Hot Isostatic Pressed test plates and prototype components of 316LN-type grade have been produced by Santasalo Powdermet Oy. They have been fully characterized and mechanically tested down to 4.2 K at CERN. The fine grained structure, the absence of residual stresses, the full isotropy of mechanical properties associated to the low level of Prior Particle Boundaries oxides ...

  20. Annual report of the Metallurgy Division [for the] period ending December 1976

    International Nuclear Information System (INIS)

    Elayaperumal, K.; Gupta, C.K.; Mukhopadhyay, P.; Rao, S.V.K.

    1977-01-01

    An account of the work done in the Metallurgy Division of the Bhabha Atomic Research Centre, Bombay, during the calendar year 1976 is given. Some of the major achievements are: (1) production of boron carbide and boral sheet for the Trombay R-5 reactor under construction, (2) production of niobium metal for the manufacture of Zr-Nb-Cu alloy garter springs, (3) development of a process for graphite coating on zircaloy, (4) studies on structural and metal physics aspects of zirconium alloys and steels, (5) studies on the corrosion behaviour of zircaloy-2 as affected by the replacement of helium and stress corrosion cracking of zircaloy fuel tubes in iodine atmosphere and (6) production of high density UO 2 pellets with stable microstructures and sinterable magnesium oxide for MHD application. (M.G.B.)

  1. Encyclopedic dictionary bilingual English-Spanish of sciences: mining, chemistry, geology, metallurgy and environment

    International Nuclear Information System (INIS)

    Munoz Maradona, M.; Bellini, M.; Busleiman, M.

    2007-01-01

    This dictionary has been designed to satisfy scientists, researchers, technicians, interpreters, translators and students' needs in the areas of chemistry, geology, mining, metallurgy and environment for they find it necessary to have an English- Spanish encyclopedia on their sciences. It is a reliable book when looking for words that are normally not included in everyday dictionaries. It is now reaching the final revision stage with more than 15,000 entries. It includes scientific terms, chemical formulas of minerals and other elements, noticeable scientists' biographies, tables, graphics, and images so as to help readers' understanding. It is divided into three columns: the first one presents the English term and its area of concern; the second, the corresponding Spanish equivalent, and in the third, a suitable explanation.(author)

  2. Microstructure, mechanical behavior and biocompatibility of powder metallurgy Nb-Ti-Ta alloys as biomedical material.

    Science.gov (United States)

    Liu, Jue; Chang, Lin; Liu, Hairong; Li, Yongsheng; Yang, Hailin; Ruan, Jianming

    2017-02-01

    Microstructures, mechanical properties, apatite-forming ability and in vitro experiments were studied for Nb-25Ti-xTa (x=10, 15, 20, 25, 35at.%) alloys fabricated by powder metallurgy. It is confirmed that the alloys could achieve a relative density over 80%. Meanwhile, the increase in Ta content enhances the tensile strength, elastic modulus and hardness of the as-sintered alloys. When increasing the sintering temperatures, the microstructure became more homogeneous for β phase, resulting in a decrease in the modulus and strength. Moreover, the alloys showed a good biocompatibility due to the absence of cytotoxic elements, and were suitable for apatite formation and cell adhesion. In conclusion, Nb-25Ti-xTa alloys are potentially useful in biomedical applications with their mechanical and biological properties being evaluated in this work. Copyright © 2016 Elsevier B.V. All rights reserved.

  3. 9th Mining and metallurgy international congress, Leon, 24-28 May 1994

    International Nuclear Information System (INIS)

    1994-01-01

    The 9th Mining and Metallurgy International Congress had 201 communications. These was articulated into 4th areas: 1.- Geological resources management and profit: 1.1- Geological and mining research on geologic resources. 1.2.- Non energetic mineral resources exploitation. 1.3- Hydro-geologic and geothermia resources. 1.4- Geologic resources and planning. 2.- Energy: 2.1.- Energetic mining.- 2.2 Oil and gas. 2.3.- Electricity production and distribution. 2.4.- Coal clean technologies. 2.5.- Energetic management. 3.- Material engineering: 3.1.- Minerallurgia and metallurgic processes. 3.2- Industrial minerals and ornamental 10cks. 3.3 .- Building materials. 3.4 Advanced technology materials. 4.- Environmental and territorial engineering in basic industry. 4.1.-Valuation of environmental impacts. 4.2.- Restoration engineering in mining. 4.3.- Effluent and residue engineering. 4.4.- Environmental management and clean technologies 4.5.- Natural and technological risks

  4. U3O8 from resin for powder-metallurgy fabrication of reactor fuel

    International Nuclear Information System (INIS)

    Mosley, W.C. Jr.

    1982-01-01

    A study was conducted to determine if cation exchange resin could be used to produce U 3 O 8 powder suitable for use in powder metallurgy fabrication of fuel tubes for production reactors at the Savannah River Plant (SRP). U 3 O 8 powders have been produced from three cation exchange resins: DOWEX (Dow Chemical Co.) 50W, AG (Bio-Rad Laboratories, Richmond, California) MP-50, and Bio-REX (Bio-Rad Laboratories, Richmond, California). This study included characterization of the thermal decomposition of uranium-loaded resins, measurement of properties of resin-based U 3 O 8 powders, and metallographic examination of U 3 O 8 -Al cores in extruded fuel tubes. Results to date show that AG MP-50 appears to be the best resin for producing U 3 O 8 powder suitable for the PM process. 20 figures

  5. Comparison Study on Additive Manufacturing (AM) and Powder Metallurgy (PM) AlSi10Mg Alloys

    Science.gov (United States)

    Chen, B.; Moon, S. K.; Yao, X.; Bi, G.; Shen, J.; Umeda, J.; Kondoh, K.

    2018-02-01

    The microstructural and mechanical properties of AlSi10Mg alloys fabricated by additive manufacturing (AM) and powder metallurgy (PM) routes were investigated and compared. The microstructures were examined by scanning electron microscopy assisted with electron-dispersive spectroscopy. The crystalline features were studied by x-ray diffraction and electron backscatter diffraction. Room-temperature tensile tests and Vickers hardness measurements were performed to characterize the mechanical properties. It was found that the AM alloy had coarser Al grains but much finer Si precipitates compared with the PM alloy. Consequently, the AM alloy showed more than 100% increment in strength and hardness compared with the PM alloy due to the presence of ultrafine forms of Si, while exhibiting moderate ductility.

  6. Separating and recycling metals from mixed metallic particles of crushed electronic wastes by vacuum metallurgy.

    Science.gov (United States)

    Zhan, Lu; Xu, Zhenming

    2009-09-15

    During the treatment of electronic wastes, a crushing process is usually used to strip metals from various base plates. Several methods have been applied to separate metals from nonmetals. However, mixed metallic particles obtained from these processes are still a mixture of various metals, including some toxic heavy metals such as lead and cadmium. With emphasis on recovering copper and other precious metals, there have hitherto been no satisfactory methods to recover these toxic metals. In this paper, the criterion of separating metals from mixed metallic particles by vacuum metallurgy is built. The results show that the metals with high vapor pressure have been almost recovered completely, leading to a considerable reduction of environmental pollution. In addition, the purity of copper in mixed particles has been improved from about 80 wt % to over 98 wt %.

  7. An Overview of Internal Fixation Implant Metallurgy and Galvanic Corrosion Effects.

    Science.gov (United States)

    Koh, Justin; Berger, Aaron; Benhaim, Prosper

    2015-08-01

    Orthopedic and hand surgery implants for internal fixation of fractures have evolved substantially over the past 50 years. Newer metal compositions have been used, and new standards have been applied to older alloys, resulting in modern implants with unique physical properties and better clinical performances. Conventional wisdom has long dictated that implanting different metals should be avoided, but few guidelines exist regarding the safety of using in proximity implant systems of dissimilar metals. To better characterize the landscape of internal fixation implant metallurgy, we have compiled the recommendations and conclusions of the currently available and pertinent literature. Copyright © 2015 American Society for Surgery of the Hand. Published by Elsevier Inc. All rights reserved.

  8. Fabrication of homogeneously dispersed graphene/Al composites by solution mixing and powder metallurgy

    Science.gov (United States)

    Zeng, Xiang; Teng, Jie; Yu, Jin-gang; Tan, Ao-shuang; Fu, Ding-fa; Zhang, Hui

    2018-01-01

    Graphene-reinforced aluminum (Al) matrix composites were successfully prepared via solution mixing and powder metallurgy in this study. The mechanical properties of the composites were studied using microhardness and tensile tests. Compared to the pure Al alloy, the graphene/Al composites showed increased strength and hardness. A tensile strength of 255 MPa was achieved for the graphene/Al composite with only 0.3wt% graphene, which has a 25% increase over the tensile strength of the pure Al matrix. Raman spectroscopy, Fourier transform infrared spectroscopy, scanning electron microscopy, and transmission electron microscopy were used to investigate the morphologies, chemical compositions, and microstructures of the graphene and the graphene/Al composites. On the basis of fractographic evidence, a relevant fracture mechanism is proposed.

  9. [Evaluation and prognosis of occupational risk in workers of nonferrous metallurgy enterprises].

    Science.gov (United States)

    Shliapnikov, D M; Kostarev, V G

    2014-01-01

    The article deals with results of a priori and a posteriori evaluation of occupational risk for workers' health. Categories of a priori occupational risk for workers are estimated as high to very high (intolerable) risk. Findings are that work conditions in nonferrous metallurgy workshop result in upper respiratory tract diseases (medium degree of occupational conditionality). Increased prevalence of such diseases among the workers is connected with length of service. The authors revealed priority factors for occupationally conditioned diseases. A promising approach in occupational medicine is creation of methods to evaluate and forecast occupational risk, that enable to specify goal parameters for prophylactic measures. For example, modelling the risk of occupationally conditioned diseases via changes in exposure to occupational factor and length of service proved that decrease of chemical concentrations in air of workplace to maximally allowable ones lowers risk of respiratory diseases from 14 to 6 cases per year, for length of service of 5 years and population risk.

  10. Characterization of Powder Metallurgy Processed Pure Magnesium Materials for Biomedical Applications

    Directory of Open Access Journals (Sweden)

    Matěj Březina

    2017-10-01

    Full Text Available Magnesium with its mechanical properties and nontoxicity is predetermined as a material for biomedical applications; however, its high reactivity is a limiting factor for its usage. Powder metallurgy is one of the promising methods for the enhancement of material mechanical properties and, due to the introduced plastic deformation, can also have a positive influence on corrosion resistance. Pure magnesium samples were prepared via powder metallurgy. Compacting pressures from 100 MPa to 500 MPa were used for samples’ preparation at room temperature and elevated temperatures. The microstructure of the obtained compacts was analyzed in terms of microscopy. The three-point bendisng test and microhardness testing were adopted to define the compacts’ mechanical properties, discussing the results with respect to fractographic analysis. Electrochemical corrosion properties analyzed with electrochemical impedance spectroscopy carried out in HBSS (Hank’s Balanced Salt Solution and enriched HBSS were correlated with the metallographic analysis of the corrosion process. Cold compacted materials were very brittle with low strength (up to 50 MPa and microhardness (up to 50 HV (load: 0.025 kg and degraded rapidly in both solutions. Hot pressed materials yielded much higher strength (up to 250 MPa and microhardness (up to 65 HV (load: 0.025 kg, and the electrochemical characteristics were significantly better when compared to the cold compacted samples. Temperatures of 300 °C and 400 °C and high compacting pressures from 300 MPa to 500 MPa had a positive influence on material bonding, mechanical and electrochemical properties. A compacting temperature of 500 °C had a detrimental effect on material compaction when using pressure above 200 MPa.

  11. Standing Concertation Committee

    CERN Multimedia

    HR Department

    2009-01-01

    Main points examined at the meeting of 24 June 2009 Results of the 2009 MARS exercise The Committee took note of the results of the 2009 MARS exercise presented by the Head of the HR Department, expressing satisfaction for the early availability of the statistics and for the fact that the analysis of the results covered the last three years. Status report on the work on the five-yearly review The Committee took note of a presentation by P. Gildemyn on the data collection procedure for the 2010 five-yearly review (staff, fellows, associate members of the personnel, CHIS) and of the proposed work schedule. Implications for employment conditions of the discussions at the Finance Committee and Council on 17 and 18 June 2009 The Chairman briefly reported on the discussions at the meetings of the Finance Committee and Council in June 2009, on the 2010-2014 medium-term plan and the 2010 preliminary draft budget, as well as on the modified strategy and goals for 2009. The Committee ...

  12. 75 FR 27614 - Shipping Coordinating Committee; Notice of Committee Meeting

    Science.gov (United States)

    2010-05-17

    ... Environment Protection Committee. --Consideration of the report of the Maritime Safety Committee... Session of the International Maritime Organization (IMO) Council to be held at the IMO headquarters in... HNS Convention. --World Maritime University: --IMO International Maritime Law Institute: --Protection...

  13. 77 FR 57637 - Shipping Coordinating Committee; Notice of Committee Meeting

    Science.gov (United States)

    2012-09-18

    ... DEPARTMENT OF STATE [Public Notice 8031] Shipping Coordinating Committee; Notice of Committee... relating to the 1977 Torremolinos Convention on the Safety of Fishing Vessels --IMO International Maritime... administrative requirements in mandatory IMO instruments --External relations: --Relations with the United...

  14. 77 FR 76164 - Shipping Coordinating Committee; Notice of Committee Meeting

    Science.gov (United States)

    2012-12-26

    ... atmospheric pollution --Development of international measures for minimizing the transfer of invasive aquatic... pollution hazards of chemicals and preparation of consequential amendments --Additional guidelines for... DEPARTMENT OF STATE [Public Notice 8133] Shipping Coordinating Committee; Notice of Committee...

  15. Ferrous-activated persulfate oxidation of arsenic(III) and diuron in aquatic system

    Energy Technology Data Exchange (ETDEWEB)

    Zhou, Lei [State Key Laboratory of Pollution Control and Resource Reuse, School of the Environment, Nanjing University, Nanjing 210023 (China); Zheng, Wei [Jiangsu Product Quality Supervision and Inspection Research Institute, Nanjing 210007 (China); Ji, Yuefei [State Key Laboratory of Pollution Control and Resource Reuse, School of the Environment, Nanjing University, Nanjing 210023 (China); Université Lyon 1, UMR CNRS 5256, Institut de recherches sur la catalyse et l’environnement de Lyon (IRCELYON), 2 Avenue Albert Einstein, F-69626 Villeurbanne (France); Zhang, Jinfeng; Zeng, Chao; Zhang, Ya; Wang, Qi [State Key Laboratory of Pollution Control and Resource Reuse, School of the Environment, Nanjing University, Nanjing 210023 (China); Yang, Xi, E-mail: yangxi@nju.edu.cn [State Key Laboratory of Pollution Control and Resource Reuse, School of the Environment, Nanjing University, Nanjing 210023 (China)

    2013-12-15

    Highlights: • Effective oxidation of As(III)/diuron is achieved by Fe(II)-activated persulfate. • Hydroxyl and sulfate radical play important roles in As(III) and diuron oxidation. • CA and Na{sub 2}S{sub 2}O{sub 3} are efficient and environmental friendly chelating agents. • DFT calculation is found to be useful for degradation products prediction. -- Abstract: In situ chemical oxidation (ISCO) can be an effective technology for the remediation of soil and groundwater polluted by organic and inorganic contaminants. This study investigated the oxidation of arsenic(III) (As(III)) and diuron using ferrous activated persulfate-based ISCO. The results indicated that Fe(II)/persulfate oxidation could be an effective method to oxidize As(III) and diuron. Effects of pH, S{sub 2}O{sub 8}{sup 2−} and Fe(II) amounts on the destruction of As(III) and diuron were examined in batch experiments. Acidic conditions favored the removal of As(III) and diuron. Four chelating agents, citric acid (CA), Na{sub 2}S{sub 2}O{sub 3}, diethylene triamine pentaacetic acid (DTPA) and ethylene diamine tetraacetic acid disodium (EDTA-Na{sub 2}) were used in attempt to maintain the quantity of ferrous ion in solution. In our experiments, CA and Na{sub 2}S{sub 2}O{sub 3} were found to be more effective than DTPA and EDTA-Na{sub 2}. Our results also revealed a widely practical prospect of inorganic chelating agent Na{sub 2}S{sub 2}O{sub 3}. Hydroxyl and sulfate radical were determined to play key roles in the oxidation process by using ethanol and tertiary butanol as molecular probes. Oxidation of As(III) yielded As(V) via the electron-transfer reaction. In the oxidation process of diuron, a stepwise nucleophilic substitution of chlorine by hydroxyl and a stepwise oxidation process of the methyl on the dimethylurea group by hydroxyl and sulfate radical were proposed.

  16. Humic acids enhance the microbially mediated release of sedimentary ferrous iron.

    Science.gov (United States)

    Chang, Chun-Han; Wei, Chia-Cheng; Lin, Li-Hung; Tu, Tzu-Hsuan; Liao, Vivian Hsiu-Chuan

    2016-03-01

    Iron (Fe) is an essential element for many organisms, but high concentrations of iron can be toxic. The complex relation between iron, arsenic (As), bacteria, and organic matter in sediments and groundwater is still an issue of environmental concern. The present study addresses the effects of humic acids and microorganisms on the mobilization of iron in sediments from an arsenic-affected area, and the microbial diversity was analyzed. The results showed that the addition of 50, 100, and 500 mg/L humic acids enhanced ferrous iron (Fe(II)) release in a time-dependent and dose-dependent fashion under anaerobic conditions. A significant increase in the soluble Fe(II) concentrations occurred in the aqueous phases of the samples during the first 2 weeks, and aqueous Fe(II) reached its maximum concentrations after 8 weeks at the following Fe(II) concentrations: 28.95 ± 1.16 mg/L (original non-sterilized sediments), 32.50 ± 0.71 mg/L (50 mg/L humic acid-amended, non-sterilized sediments), 37.50 ± 1.85 mg/L (100 mg/L humic acid-amended, non-sterilized sediments), and 39.00 ± 0.43 mg/L (500 mg/L humic acid-amended, non-sterilized sediments). These results suggest that humic acids can further enhance the microbially mediated release of sedimentary iron under anaerobic conditions. By contrast, very insignificant amounts of iron release were observed from sterilized sediments (the abiotic controls), even with the supplementation of humic acids under anaerobic incubation. In addition, the As(III) release was increased from 50 ± 10 μg/L (original non-sterilized sediments) to 110 ± 45 μg/L (100 mg/L humic acid-amended, non-sterilized sediments) after 8 weeks of anaerobic incubation. Furthermore, a microbial community analysis indicated that the predominant class was changed from Alphaproteobacteria to Deltaproteobacteria, and clearly increased populations of Geobacter sp., Paludibacter sp., and Methylophaga sp. were found after adding humic acids

  17. Committees and supporting organizations

    Science.gov (United States)

    2011-09-01

    Advisory Committee:Organizing Committee: Marcello Baldo (Catania)Takaharu Otsuka (Tokyo), co-chair George Bertsch (Seattle)Michael Urban (Orsay), co-chair Jean-Paul Blaizot (Saclay)Taiichi Yamada (Yokohama) Michel Girod (Bruyères-le-Châtel)Nguyen van Giai (Orsay) Hisashi Horiuchi (Osaka)Shinichiro Fujii (Tokyo) Umberto Lombardo (Catania)Jérôme Margueron (Orsay) Gerd Röpke (Rostock)Kouichi Hagino (Sendai) Hiroyuki Sagawa (Aizu)Yoshiko Kanada-En'yo (Kyoto) Piet Van Isacker (Caen) Enrico Vigezzi (Milano) IPN logo    EFES logo    CNRS logo    ihp logo

  18. Preparation of ferrous chelate of hairtail (Trichiurus haumela) protein hydrolysate (Fe(II)-HPH) and its antibacterial activity

    Science.gov (United States)

    Lin, Huimin; Zhang, Bin; Yu, Tian; Deng, Shanggui

    The preparation of a ferrous chelate of hairtail (Trichiurus haumela) protein hydrolysate (Fe(II)-HPH) and its antibacterial activity were studied. The optimal conditions of hydrolysis by papain and ferrous chelation were obtained by single-factor experiments and orthogonal test, with the antibacterial activities as the index. In addition, the antibacterial activity of Fe(II)-HPH was evaluated using the Plackett-Burman design. The orthogonal test results showed that Fe(II)-HPH had an antibacterial activity of 98.3% under a temperature of 40 °C at pH 6.5 for an enzymolysis duration of eight hours in the presence of 20,000 U/g of enzyme. The Plackett-Burman design analysis showed that the three most significant factors (P < 0.05) influencing the antibacterial activity of Fe(II)-HPH were pH, the concentration (mg/mL), and presence of magnesium sulfate.

  19. Chromium content in human skin after in vitro application of ordinary cement and ferrous-sulphate-reduced cement

    DEFF Research Database (Denmark)

    Fullerton, A; Gammelgaard, Bente; Avnstorp, C

    1993-01-01

    The amount of chromium found in human skin after in vitro application of cement suspensions on full-thickness human skin in diffusion cells was investigated. Cement suspensions made from ordinary Portland cement or Portland cement with the chromate reduced with added ferrous sulphate were used....... The cement suspensions were either applied on the skin surface under occlusion for 48 h or applied repeatedly every 24 h for 96 h. No statistically significant difference in chromium content of skin layers between skin exposed to ordinary Portland cement, skin exposed to cement with added ferrous sulphate...... and unexposed skin was observed, despite a more permeable skin barrier at the alkaline pH of the cement suspensions, i.e., pH 12.5. Increased chromium levels in epidermis and dermis were seen when ordinary Portland cement was applied as a suspension with added sodium sulphate (20%) on the skin surface for 96 h...

  20. The ferrous ammonium sulfate solid system, as dosemeter for processes at low temperatures and high doses of gamma radiation

    International Nuclear Information System (INIS)

    Juarez C, J.M.; Ramos B, S.; Negron M, A.

    2005-01-01

    This paper presents the results obtained from a study of the radiation induced oxidation of crystalline ferrous ammonium sulfate with gamma rays at 295 K, 263 K and 77 K and dose from 0 to 300 kGy. The radiation induced decomposition of ferrous ammonium sulfate has been studied by the dissolution of the irradiated salt in 0,8 N sulfuric acid. The main product is Fe 3+ and molar concentration of ferric ion was determined spectrophotometrically in the UV region at 304 nm. The optical density values showed a linear dependence with dose, indicating that the data obtained might be used to create a calibrating curve. Color in irradiated salt changes from blue to green, yellow and orange according to the absorbed dose. The accuracy and the reproducibility of the system were tested. In addition, some other characteristics make possible the use of this system as a dosimeter, similar to Fricke chemical dosemeter, at low temperatures and high dose. (Author)

  1. Federal Advisory Committees at EPA

    Science.gov (United States)

    FACA committees are created to obtain advice on a wide range of environmental issues. Every committee meeting, no matter what the subject matter or where it is held, is dedicated to open government and citizen participation.

  2. List of unclassified documents by the staff of Metallurgy Division, AERE Harwell from January 1972 to July 1977

    International Nuclear Information System (INIS)

    Wallis, V.

    1977-11-01

    This list constitutes unclassified material published or presented between January 1972 and July 1977 by the staff of Metallurgy Division. It covers reports, memoranda, bibliographies, articles in periodicals, conference papers, books, theses and patent specifications. It is planned to issue a list annually. The publications are listed under the following titles of the research teams concerned: fast reactor fuels, advanced reactor systems, fracture studies, structural materials, radiation effects, composite materials, high voltage microscope and metals fabrication, management and administration. (U.K.)

  3. The physiological concentration of ferrous iron (II) alters the inhibitory effect of hydrogen peroxide on CD45, LAR and PTP1B phosphatases.

    Science.gov (United States)

    Kuban-Jankowska, Alicja; Gorska, Magdalena; Jaremko, Lukasz; Jaremko, Mariusz; Tuszynski, Jack A; Wozniak, Michal

    2015-12-01

    Hydrogen peroxide is an important regulator of protein tyrosine phosphatase activity via reversible oxidation. However, the role of iron in this reaction has not been yet elucidated. Here we compare the influence of hydrogen peroxide and the ferrous iron (reagent for Fenton reaction) on the enzymatic activity of recombinant CD45, LAR, PTP1B phosphatases and cellular CD45 in Jurkat cells. The obtained results show that ferrous iron (II) is potent inhibitor of CD45, LAR and PTP1B, but the inhibitory effect is concentration dependent. We found that the higher concentrations of ferrous iron (II) increase the inactivation of CD45, LAR and PTP1B phosphatase caused by hydrogen peroxide, but the addition of the physiological concentration (500 nM) of ferrous iron (II) has even a slightly preventive effect on the phosphatase activity against hydrogen peroxide.

  4. Alginate inhibits iron absorption from ferrous gluconate in a randomized controlled trial and reduces iron uptake into Caco-2 cells.

    Directory of Open Access Journals (Sweden)

    Anna A Wawer

    Full Text Available Previous in vitro results indicated that alginate beads might be a useful vehicle for food iron fortification. A human study was undertaken to test the hypothesis that alginate enhances iron absorption. A randomised, single blinded, cross-over trial was carried out in which iron absorption was measured from serum iron appearance after a test meal. Overnight-fasted volunteers (n = 15 were given a test meal of 200 g cola-flavoured jelly plus 21 mg iron as ferrous gluconate, either in alginate beads mixed into the jelly or in a capsule. Iron absorption was lower from the alginate beads than from ferrous gluconate (8.5% and 12.6% respectively, p = 0.003. Sub-group B (n = 9 consumed the test meals together with 600 mg calcium to determine whether alginate modified the inhibitory effect of calcium. Calcium reduced iron absorption from ferrous gluconate by 51%, from 11.5% to 5.6% (p = 0.014, and from alginate beads by 37%, from 8.3% to 5.2% (p = 0.009. In vitro studies using Caco-2 cells were designed to explore the reasons for the difference between the previous in vitro findings and the human study; confirmed the inhibitory effect of alginate. Beads similar to those used in the human study were subjected to simulated gastrointestinal digestion, with and without cola jelly, and the digestate applied to Caco-2 cells. Both alginate and cola jelly significantly reduced iron uptake into the cells, by 34% (p = 0.009 and 35% (p = 0.003 respectively. The combination of cola jelly and calcium produced a very low ferritin response, 16.5% (p < 0.001 of that observed with ferrous gluconate alone. The results of these studies demonstrate that alginate beads are not a useful delivery system for soluble salts of iron for the purpose of food fortification.ClinicalTrials.gov NCT01528644.

  5. The maturation state of the auditory nerve and brainstem in rats exposed to lead acetate and supplemented with ferrous sulfate.

    Science.gov (United States)

    Zucki, Fernanda; Morata, Thais C; Duarte, Josilene L; Ferreira, Maria Cecília F; Salgado, Manoel H; Alvarenga, Kátia F

    The literature has reported the association between lead and auditory effects, based on clinical and experimental studies. However, there is no consensus regarding the effects of lead in the auditory system, or its correlation with the concentration of the metal in the blood. To investigate the maturation state of the auditory system, specifically the auditory nerve and brainstem, in rats exposed to lead acetate and supplemented with ferrous sulfate. 30 weanling male rats (Rattus norvegicus, Wistar) were distributed into six groups of five animals each and exposed to one of two concentrations of lead acetate (100 or 400mg/L) and supplemented with ferrous sulfate (20mg/kg). The maturation state of the auditory nerve and brainstem was analyzed using Brainstem Auditory Evoked Potential before and after lead exposure. The concentration of lead in blood and brainstem was analyzed using Inductively Coupled Plasma-Mass Spectrometry. We verified that the concentration of Pb in blood and in brainstem presented a high correlation (r=0.951; p<0.0001). Both concentrations of lead acetate affected the maturation state of the auditory system, being the maturation slower in the regions corresponding to portion of the auditory nerve (wave I) and cochlear nuclei (wave II). The ferrous sulfate supplementation reduced significantly the concentration of lead in blood and brainstem for the group exposed to the lowest concentration of lead (100mg/L), but not for the group exposed to the higher concentration (400mg/L). This study indicate that the lead acetate can have deleterious effects on the maturation of the auditory nerve and brainstem (cochlear nucleus region), as detected by the Brainstem Auditory Evoked Potentials, and the ferrous sulphate can partially amend this effect. Copyright © 2017 Associação Brasileira de Otorrinolaringologia e Cirurgia Cérvico-Facial. All rights reserved.

  6. Electronic environments of ferrous iron in rhyolitic and basaltic glasses at high pressure: Silicate Glasses at High Pressure

    Energy Technology Data Exchange (ETDEWEB)

    Solomatova, Natalia V. [Division of Geological and Planetary Sciences, Caltech, Pasadena California USA; Jackson, Jennifer M. [Division of Geological and Planetary Sciences, Caltech, Pasadena California USA; Sturhahn, Wolfgang [Division of Geological and Planetary Sciences, Caltech, Pasadena California USA; Rossman, George R. [Division of Geological and Planetary Sciences, Caltech, Pasadena California USA; Roskosz, Mathieu [IMPMC-Muséum National d' Histoire Naturelle-CNRS, Paris France

    2017-08-01

    The physical properties of silicate melts within Earth's mantle affect the chemical and thermal evolution of its interior. Chemistry and coordination environments affect such properties. We have measured the hyperfine parameters of iron-bearing rhyolitic and basaltic glasses up to ~120 GPa and ~100 GPa, respectively, in a neon pressure medium using time domain synchrotron Mössbauer spectroscopy. The spectra for rhyolitic and basaltic glasses are well explained by three high-spin Fe2+-like sites with distinct quadrupole splittings. Absence of detectable ferric iron was confirmed with optical absorption spectroscopy. The sites with relatively high and intermediate quadrupole splittings are likely a result of fivefold and sixfold coordination environments of ferrous iron that transition to higher coordination with increasing pressure. The ferrous site with a relatively low quadrupole splitting and isomer shift at low pressures may be related to a fourfold or a second fivefold ferrous iron site, which transitions to higher coordination in basaltic glass, but likely remains in low coordination in rhyolitic glass. These results indicate that iron experiences changes in its coordination environment with increasing pressure without undergoing a high-spin to low-spin transition. We compare our results to the hyperfine parameters of silicate glasses of different compositions. With the assumption that coordination environments in silicate glasses may serve as a good indicator for those in a melt, this study suggests that ferrous iron in chemically complex silicate melts likely exists in a high-spin state throughout most of Earth's mantle.

  7. Natural analogues for expansion due to the anaerobic corrosion of ferrous materials

    Energy Technology Data Exchange (ETDEWEB)

    Smart, N.R.; Adams, R. [Serco Assurance, Culham Science Centre (United Kingdom)

    2006-10-15

    In Sweden, spent nuclear fuel will be encapsulated in sealed cylindrical canisters, consisting of a cast iron insert and a copper outer container. The canisters will be placed in a deep geologic repository and surrounded by bentonite. If a breach of the outer copper container were to occur the cast iron insert would undergo anaerobic corrosion, forming a magnetite film whose volume would be greater than that of the base metal. In principle there is a possibility that accumulation of iron corrosion product could cause expansion of the copper canister. Anaerobic corrosion rates are very slow, so in the work described in this report reference was made to analogous materials that had been corroding for long periods in natural anoxic aqueous environments. The report considers the types of naturally occurring environments that may give rise to anoxic environments similar to deep geological groundwater and where ferrous materials may be found. Literature information regarding the corrosion of iron archaeological artefacts is summarised and a number of specific archaeological artefacts containing iron and copper corroding in constrained geometries in anoxic natural waters are discussed in detail. No evidence was obtained from natural analogues which would suggest that severe damage is likely to occur to the SKB waste canister design as a result of expansive corrosion of cast iron under repository conditions.

  8. Natural analogues for expansion due to the anaerobic corrosion of ferrous materials

    International Nuclear Information System (INIS)

    Smart, N.R.; Adams, R.

    2006-10-01

    In Sweden, spent nuclear fuel will be encapsulated in sealed cylindrical canisters, consisting of a cast iron insert and a copper outer container. The canisters will be placed in a deep geologic repository and surrounded by bentonite. If a breach of the outer copper container were to occur the cast iron insert would undergo anaerobic corrosion, forming a magnetite film whose volume would be greater than that of the base metal. In principle there is a possibility that accumulation of iron corrosion product could cause expansion of the copper canister. Anaerobic corrosion rates are very slow, so in the work described in this report reference was made to analogous materials that had been corroding for long periods in natural anoxic aqueous environments. The report considers the types of naturally occurring environments that may give rise to anoxic environments similar to deep geological groundwater and where ferrous materials may be found. Literature information regarding the corrosion of iron archaeological artefacts is summarised and a number of specific archaeological artefacts containing iron and copper corroding in constrained geometries in anoxic natural waters are discussed in detail. No evidence was obtained from natural analogues which would suggest that severe damage is likely to occur to the SKB waste canister design as a result of expansive corrosion of cast iron under repository conditions

  9. Characterization of naturally occurring radioactive materials and Cobald-60 contaminated ferrous scraps from steel industries

    International Nuclear Information System (INIS)

    Chao, H.E.; Chiu, H.S.; Hunga, J.Y.; His, H.W.; Chen, Y.B.

    2002-01-01

    Since the occurrence of radioactively contaminated rebar incident in 1992, steel industries in Taiwan were encouraged by Atomic Energy Council (AEC) to install portal monitor to detect the abnormal radiation in shipments of metal scrap feed. From 1994 through 1999, there were 53 discoveries of radioactivity in ferrous scraps by steel companies. These include 15 orphan radioactive sources, 16 cobalt-60 contaminated rebars, 20 Naturally Occurring Radioactive Material (NORM) contaminated scraps, and two unknowns. Most NORM-contaminated scraps were from abroad. The NORM and cobalt-60 contaminated scraps were taken from the steel mills and analyzed in laboratory. The analytical results of scales and sludge sampled from NORM-contaminated scraps combining with the circumstantial evidences indicate that five possible industrial processes may be involved. They are oil production and treatment, heavy mineral sand benefication and rare earth processing, copper mining and processing, recovery of ammonium chloride by lime adsorption in Ammonium-soda process, and tailing of uranium enrichment process. The cobalt-60 activity and trace elements concentrations of contaminated rebars confirm that all of them were produced domestically in the period from Oct. 1982 to Jan. 1983, when the cobalt-60 sources were lost and entered the electric arc furnace to produce the contaminated rebars. (author)

  10. On the characterisation of the corrosion layout of ferrous archaeological analogues in binders

    International Nuclear Information System (INIS)

    Chitty, Walter-John; Dillmann, Philippe; L'Hostis, Valerie; Beranger, Gerard

    2004-01-01

    This paper deals with an analytical study on ferrous reinforcements embedded in hydraulic binders found in ancient buildings from the Middle Age period to the beginning of the 20. c. AD. The study of these kind of archaeological analogues is necessary to improve the knowledge on the long-term corrosion of low carbon steels that could be used in concrete to build the substructure of nuclear wastes reversible storage facilities. The corrosion system can be described as a multi-layer pattern made of the metal, a dense corrosion product layer, a transformed medium and a binder. All the morphological and physicochemical properties as composition, structure and porosities of these different parts were studied with different analytical methods as optical and electron microscopy, EDS coupled to SEM, EPMA, mercury porosimetry, micro Raman spectroscopy and micro Diffraction under Synchrotron Radiation. Moreover, average corrosion rates were evaluated by two different methods. These rates are relatively low compared to the same parameters measured on low alloyed steels immersed in aqueous environments and are comparable with results obtained for passivated systems. (authors)

  11. Surface treatment of non-ferrous metals for the purpose of gas analysis

    International Nuclear Information System (INIS)

    Quaglia, L.; Weber, G.; Triffaux, J.; Geerts, J.; Audenhove, J. van; Pauwels, J.

    1979-01-01

    The present report is an updating of earlier reports published in 1972 and 1976. Its major improvement compared to the earlier reports is that greater importance has been devoted to quantify the parameters of mechanical shaping techniques to be used with or without subsequent chemical etching. Surface treatments have been studied and standardized for a number of non-ferrous metals. Recommendations were generally made on the basis of the following: the proposed treatment must give a minimum surface content; it must exhibit good reproducibility; it must be easy to perform with equipment normally available in analytical laboratories. The recommended treatments are presented in the form of sheets. They give full information on mechanica shaping parameters if these are important, and -if needed- the subsequent chemical etching conditions. Typical residual surface contents are given for oxygen carbon and nitrogen. They refer to samples freshly prepared. The metals or alloys concerned are: aluminium, aluminium alloyed with 3%, 7% and 13% silicon, copper, lead, nickel, titanium, TiAl 6 V 4 zirconium, tungsten and molybdenum

  12. Stress Analysis of Non-Ferrous Metals Welds by Numerical Simulation

    Directory of Open Access Journals (Sweden)

    Kravarikova Helena

    2017-01-01

    Full Text Available Thermal energy welded material unevenly heated and thus supports the creation of tension. During the fusing process welding transient tensions generated in the welded material. Generation of the transient tensions depends on the thermal expansion and fixed permanently welded parts. Tensions are the result of the interaction of material particles. For welded parts and constructions it is necessary to know the size and direction of application of tensions. The emerging tensions can cause local change or a total deformation of welded materials. Deformations and residual stresses impair the performance of a welded construction, reduces the stability of the parts. To reduce or eliminate of action or a screening direction stresses and strains it is necessary to know the mechanism of their emergence. It is now possible to examine the emergence of tensions numerical experiments on any model using numerical simulation using FEM. Results of numerical experiment is the analysis of stress and deformation course. In the plane the tension it divided into normal σ and τ tangential folders. Decomposition stress on components simplifies the stress analysis. The results obtained from numerical analysis are correct to predict the stress distribution and size. The paper presents the results of numerical experiments stress analysis solutions fillet welds using FEM numerical simulation of welding of non-ferrous metals.

  13. Resistance to High-Temperature Oxidation and Wear of Various Ferrous Alloys Used in Rolling Mills

    Science.gov (United States)

    Delaunois, Fabienne; Stanciu, Victor Ioan; Sinnaeve, Mario

    2018-01-01

    Various materials are commonly used to manufacture work rolls for hot rolling mills, such as ICDP (Indefinite Chill Double Pour) cast irons, high-chromium white cast irons, and high speed steels (HSS). Various chemical compositions and microstructures are studied in order to optimize the in-use behavior of those grades of rolls. In this paper, six grades of ferrous alloys (an ICDP cast iron; an ICDP cast iron enriched in vanadium, niobium, and molybdenum; a HSS; a graphitic HSS; a high-chromium white cast iron (Hi-Cr); and a niobium-molybdenum-doped high-chromium white cast iron) were investigated. High-temperature oxidation tests with gravimetric means at 575 °C in water vapor atmosphere and sliding wear tests were carried out. The oxidation kinetics was followed during oxidation test. The microstructure was observed by optical and scanning electron microscopies. The oxides formed on the surface of the samples were analyzed by XRD and EDS. The thickness of the oxide scales and the mass gain were measured after oxidation test. The results showed that the behavior of all the grades differed. The oxide scale of HSS and HSS-G grades was fine and their friction coefficient was low. The weight gain after oxidation test of HSS was high. Hi-Cr and M-Hi-Cr grades presented highly porous oxide layer and an important increase of the friction coefficient during wear test. ICDP and M-ICDP had intermediate behavior.

  14. Effect of ferrous sulphate on haematological, biochemical and immunological parameters in neonatal calves

    Directory of Open Access Journals (Sweden)

    Lobna S. Elgebaly

    2010-09-01

    Full Text Available The effect of oral administration of iron on haematological, biochemical and immunological parameters in neonatal calves was studied. Ten calves from a private farm in Gharbia Governorate were used. Calves were separated from their dams immediately after birth and received colostrum during the first hours after calving and twice daily for 48 h. Thereafter, they received whole milk. Calves were divided into two equal groups. The first group was kept as controls. Calves of the second group were given ferrous sulphate at a dose of 250 mg/calf daily, beginning at one day of age; this was continued for 28 days. Three blood samples were collected from each calf in all groups at 14, 21, 28 and 35 days of age. Iron administration produced a significant increase in red blood cell count, haemoglobin, packed cell volume and blood indices, in addition to non-significant changes in total and differential leukocyte counts. The administration of iron resulted in a significant increase in serum iron, total proteins, globulins, thyroid hormones, lymphocyte stimulation index, phagocytosis, body weight and body gain. The administration of iron is suggested as routine practice in calf-producing farms due to its advantageous effects on the parameters tested.

  15. Improvement of the Wear Resistance of Ferrous Alloys by Electroless Plating of Nickel

    Science.gov (United States)

    Kaleicheva, J. K.; Karaguiozova, Z.

    2018-01-01

    The electroless nickel (Ni) and composite nickel - nanodiamond (Ni+DND) coatings are investigated in this study. The method EFTTOM-NICKEL for electroless nickel plating with nanosized strengthening particles (DND 4-6 nm) is applied for the coating deposition. The coatings are deposited on ferrous alloys samples. The wear resistance of the coatings is performed by friction wear tests under 50-400 MPa loading conditions - in accordance with a Polish Standard PN-83/H-04302. The microstructure observations are made by optic metallographic microscope GX41 OLIMPUS and the microhardness is determined by Vickers Method. Tests for wear resistance, thickness and microhardness measurements of the coatings without heat treatment and heat treatment are performed. The heat treatment regime is investigated with the aim to optimize the thermal process control of the coated samples without excessive tempering of the substrate material. The surface fatigue failure is determined by contact fatigue test with the purpose to establish suitable conditions for production of high performance materials.

  16. Modified ferrous ammonium sulfate benzoic acid xyelenol orange (MFBX) and thermoluminescent dosimeters - a comparative study

    International Nuclear Information System (INIS)

    Brindha, S.; Rose, J.V.R.; Sathyan, S.; Singh, Rabi Raja I.; Ravindran, B. Paul

    2002-01-01

    Radiation dosimetry deals with the determination of absorbed dose to the medium exposed to ionizing radiation. Chemical dosimetry depends on oxidation or reduction of chemicals by ionizing radiation. A ferrous ammonium sulfate benzoic acid xyelenol orange (FBX) dosimeter based on this principle is being used as a clinical dosimeter at present. Certain modifications were carried out in the preparation and storage of the FBX dosimeter to increase its shelf life. The resulting dosimeter was called a modified FBX (MFBX) dosimeter and has been used in our department for the past few years. An extensive study of the dose, dose rate and energy response of the dosimeter was carried out and compared with a thermoluminescent (LiF 7 ) dosimeter. The results obtained were found to be comparable to the thermoluminescent (LiF 7 ) dosimeter. Hence it was concluded that the MFBX dosimeter could be used for phantom dosimetry, data collection and in vivo measurements. Easier preparation and availability of the reagents are added advantages of using MFBX as a clinical dosimeter in small radiotherapy departments. (author)

  17. Resistance to High-Temperature Oxidation and Wear of Various Ferrous Alloys Used in Rolling Mills

    Science.gov (United States)

    Delaunois, Fabienne; Stanciu, Victor Ioan; Sinnaeve, Mario

    2018-03-01

    Various materials are commonly used to manufacture work rolls for hot rolling mills, such as ICDP (Indefinite Chill Double Pour) cast irons, high-chromium white cast irons, and high speed steels (HSS). Various chemical compositions and microstructures are studied in order to optimize the in-use behavior of those grades of rolls. In this paper, six grades of ferrous alloys (an ICDP cast iron; an ICDP cast iron enriched in vanadium, niobium, and molybdenum; a HSS; a graphitic HSS; a high-chromium white cast iron (Hi-Cr); and a niobium-molybdenum-doped high-chromium white cast iron) were investigated. High-temperature oxidation tests with gravimetric means at 575 °C in water vapor atmosphere and sliding wear tests were carried out. The oxidation kinetics was followed during oxidation test. The microstructure was observed by optical and scanning electron microscopies. The oxides formed on the surface of the samples were analyzed by XRD and EDS. The thickness of the oxide scales and the mass gain were measured after oxidation test. The results showed that the behavior of all the grades differed. The oxide scale of HSS and HSS-G grades was fine and their friction coefficient was low. The weight gain after oxidation test of HSS was high. Hi-Cr and M-Hi-Cr grades presented highly porous oxide layer and an important increase of the friction coefficient during wear test. ICDP and M-ICDP had intermediate behavior.

  18. Ferrous iron mediated oxidation of arachidonic acid: studies employing nitroblue tetrazolium (NBT).

    Science.gov (United States)

    Peterson, D A; Gerrard, J M; Rao, G H; Krick, T P; White, J G

    1978-10-01

    The oxidation of arachidonic acid by ferrous sulfate provides a useful model to study the role of iron in lipid oxidation reactions. We have employed nitroblue tetrazolium (NBT) in the present investigation to evaluate the mechanism of this reaction. In the presence of arachidonic acid, Fe +++, and O2, the yellow dye NBT was rapidly reduced to the blue form, NBTH2. The molar ratio of arachidonic acid to Fe++ in this rapid reaction was 1:1, showing an interaction of one fatty acid molecule per iron molecule. Approximately one molecule of NBT was reduced per four molecules of arachidonic acid and Fe++. Reduction of NBT was accompanied by oxidation of Fe++ to Fe+++, suggesting the transfer of four electrons from the Fe++ to NBT to reduce the dye. Arachidonic acid was found to be unchanged when extracted at the end of the reaction, indicating formation of a complex that could dissociate leaving intact arachidonic acid. Evidence for the presence of such a complex which slowly dissociates during the reaction was obtained after longer incubations with small amounts of arachidonic acid. NBT reduction was not inhibited by agents which hydrolyze superoxide, by catalase or by agents which trap hydroxy radicals. We, therefore, propose a model in which NBT traps a radical generated on the arachidonic acid molecule. The proposed model suggests mechanisms for other fatty acid oxidation reactions such as prostaglandin and hydroperoxy fatty acid synthesis.

  19. Effect of ferrous sulfate fortification in germinated brown rice on seed iron concentration and bioavailability.

    Science.gov (United States)

    Wei, Yanyan; Shohag, M J I; Ying, Feng; Yang, Xiaoe; Wu, Chunyong; Wang, Yuyan

    2013-06-01

    The present study evaluated the effectiveness of germination and iron fortification on iron concentration and bioavailability of brown rice. Iron fortification during germination process with 0.05-2 g/L ferrous sulfate increased the iron concentration in germinated brown rice from 1.1 to 15.6 times than those in raw brown rice. Based on the recommended dietary allowance of iron, maximum germination rate and γ-aminobutyric acid, we recommend the brown rice fortified with 0.25 g/L FeSO(4) as a suitable fortification level to use in germination process. Iron fortification during the germination process has a positive effect on iron concentration and bioavailability. A significant difference was observed among the cultivars in respect to the capacity for iron accumulation and bioavailability. Germination alone could improve in vitro iron solubility, but had no effect on iron bioavailability in Caco-2 cell, the additional fortification process should be combined to get high amount of bioavailable iron from the brown rice. Copyright © 2012 Elsevier Ltd. All rights reserved.

  20. INTERPRETATION OF AT-LINE SPECTRA FROM AFS-2 BATCH #3 FERROUS SULFAMATE TREATMENT

    Energy Technology Data Exchange (ETDEWEB)

    Kyser, E.; O' Rourke, P.

    2013-12-10

    Spectra from the “at-line” spectrometer were obtained during the ferrous sulfamate (FS) valence adjustment step of AFS-2 Batch #3 on 9/18/2013. These spectra were analyzed by mathematical principal component regression (PCR) techniques to evaluate the effectiveness of this treatment. Despite the complications from Pu(IV), we conclude that all Pu(VI) was consumed during the FS treatment, and that by the end of the treatment, about 85% was as Pu(IV) and about 15% was as Pu(III). Due to the concerns about the “odd” shape of the Pu(IV) peak and the possibility of this behavior being observed in the future, a follow-up sample was sent to SRNL to investigate this further. Analysis of this sample confirmed the previous results and concluded that it “odd” shape was due to an intermediate acid concentration. Since the spectral evidence shows complete reduction of Pu(VI) we conclude that it is appropriate to proceed with processing of this the batch of feed solution for HB-Line including the complexation of the fluoride with aluminum nitrate.

  1. SENIOR STAFF ADVANCEMENT COMMITTEE (SSAC)

    CERN Multimedia

    2000-01-01

    Composition and mandateThe Senior Staff Advancement Committee is composed of members nominated ad persona by the Director-General.The Committee examines proposals from Divisions concerning promotions to grade 13 in Career Path IX, changes of career path to Career Path IX and advancements to the exceptional grade in Career path VIII.The Director-General may consult the Committee on any matter related to senior staff careers.The Committee makes its recommendations to the Director-General.

  2. Application of vacuum metallurgy to separate pure metal from mixed metallic particles of crushed waste printed circuit board scraps.

    Science.gov (United States)

    Zhan, Lu; Xu, Zhenming

    2008-10-15

    The principle of separating pure metal from mixed metallic particles (MMPs) byvacuum metallurgy is that the vapor pressures of various metals at the same temperature are different As a result, the metal with high vapor pressure and low boiling point can be separated from the mixed metals through distillation or sublimation, and then it can be recycled through condensation under a certain condition. The vacuum metallurgy separation (VMS) of MMPs of crushed waste printed circuit boards (WPCBs) has been studied in this paper. Theoretical analyses show that the MMPs (copper, zinc, bismuth, lead, and indium, for example) can be separated by vacuum metallurgy. The copper particles (0.15-0.20 mm) and zinc particles (<0.30 mm) were chosen to simulate the MMPs of crushed WPCBs. Experimental results show that the separated efficiency of zinc in the copper-rich particles achieves 96.19 wt % when the vacuum pressure is 0.01-0.10 Pa, the heating temperature is 1123 K, and the heating time is 105 min. Under this operation condition, the separated efficiency of zinc in the copper-rich particles from crushed WPCBs achieves 97.00 wt % and the copper purity increases from 90.68 to 99.84 wt %.

  3. Plasma Science Committee (PLSC)

    International Nuclear Information System (INIS)

    1990-01-01

    The Plasma Science Committee (PLSC) is a standing committee under the auspices of the Board on Physics and Astronomy, Commission on Physical Sciences, Mathematics, and Applications of the National Academy of Sciences--National Research Council. Plasma sciences represent a broad and diverse field. The PLSC has accepted the responsibility of monitoring the continuing development and assessing the general health of the field as whole. Although select advisory bodies have been created to address specific issues that affect plasma science, such as the Fusion Policy Advisory Committee (FPAC), the PLSC provides a focus for the plasma science community that is unique and essential. The membership of the PLSC is drawn from research laboratories in universities, industry, and government. Areas of expertise on the committee include accelerators and beams, space physics, astrophysics, computational physics and applied mathematics, fusion plasmas, fundamental experiments and theory, radiation sources, low temperature plasmas, and plasma-surface interactions. The PLSC is well prepared to respond to requests for studies on specific issues. This report discusses ion of the PLSC work

  4. New radiation technologies and methods for control of technological processes in metallurgy

    International Nuclear Information System (INIS)

    Zaykin, Yu.

    1996-01-01

    Radiation Technology of Metal and Ceramic Production with Enhanced Service Properties. Based on application of radiation technique in powder metallurgy the new technology for obtaining metals, alloys and ceramic materials with high service properties is worked out. Radiation processing of powder materials at the certain stage of the process leads to profound structure alterations at all further stages and eventually effects the properties of the resulting product. Theoretical calculation and experimental studies of electron-positron annihilation in powder-pressed samples showed that irradiation caused powder particles surface state changes favorable for further sintering and crystallization processes development. It is shown that irradiation of metal powders and powder-pressed samples by high energy electrons is technologically most efficient. The right choice of the type-and the mode of the radiation processing makes it possible to obtain metals, alloys and ceramic materials (Mo,Fe, W, Al, Ni, Cu, stainless steels, ceramics, etc.) with homogeneous structure and stable enhanced service properties. The project on radiation technology application to powder metallurgy represented by a group of authors was awarded with the diploma and the gold medal at the 22 International Exhibition of Inventions (Geneva, 1994). New Technologic Opportunities of the Chromium-Nickel Alloys Processing To obtain the required phase-structure state special methods of the chromium-nickel alloy processing for sensitive elastic devices production were worked out combining plastic deformation, thermal and radiation processing. It is shown that h-gbb phase transfer not observed before is possible in extremely non-equilibrium conditions under electron irradiation. It is established that the complex reaction of recrystallization and gb-phase deposition proceeds under electron irradiation at the room temperature when the certain threshold plastic deformation degree is reached that leads to the same

  5. An experimental determination of ferrous chloride and acetate complexation in aqueous solutions to 300°C

    Science.gov (United States)

    Palmer, Donald A.; Hyde, K. E.

    1993-04-01

    The formation of the monochloroiron(II) complex, FeCl +, was studied potentiometrically from 125 to 295°C at 25 degree intervals at one molal ionic strength in aqueous solutions containing acetic acid, sodium acetate, and sodium trifluoromethanesulfonate. In this method, competition between chloride and acetate ions for the ferrous cation resulted in a change in solution pH, which in turn was monitored in situ in a hydrogen-electrode, concentration cell. A simple empirical approach was used to extrapolate these formation quotients to infinite dilution. The resulting constants proved to be in excellent agreement with previous spectrophotometric results obtained from 25 to 200°C. Thus, the present study confirms the validity of the conclusions made based on these earlier data concerning the solubility of Fe-containing minerals in hydrothermal brines. Formation constants at infinite dilution for FeCl + are compared with the stability of ferrous acetate and hydroxide complexes. The original potentiometric titration data for ferrous acetate complex formation were combined in a new fit with values determined from the present study at unit ionic strength. Two empirical treatments (namely the isocoulombic method and the temperature/water density function) were considered for fitting and extrapolating the infinite dilution formation constants to 350°C.

  6. Ferrous Ion Chelating, Superoxide Anion Radical Scavenging and Tyrosinase Inhibitory Properties of Pure and Commercial Essential Oils of Anetrhum Graveolens

    Directory of Open Access Journals (Sweden)

    Sh Darvish Alipour Astaneh

    2013-04-01

    Full Text Available Introduction: Despite slight toxicities of essential oils, they are not under strict control in many countries. Anethum graveolens is widely consumed and its essential oils are at public reach. This study was designed to study essential oils of Anethum graveolens. Methods: The biological properties of pure and commercial essential oils of Anethum graveolens were investigated. In fact, Ferrous ion chelating activity, superoxide anion radical scavenging property, tyrosinase inhibition and total flavonoids of the oils were determined. Results: Chelating activity of 7.8 µg of EDTA was equivalent to 2 µg of the pure oil. The oils had superoxide anion radical scavenging activities which may be related to their total phenol and flavonoid contents. IC50 of ferrous ion chelating, antityrosiase and superoxide anion radical scavenging activities of pure and commercial oils were 1.3, 1.4, 1 and (171.6, 589, 132 µg respectively. Antityrosiase activity of 6.4 µg pure oil was equal to 1000 µg of the commercial oil. Conclusion: Anethum possesses antioxidative and free radical scavenging properties. This oil chelates ferrous ions and superoxide radicals. It is effective in formation of reactive toxic products. Anethum has good potentials regarding its applications in food and drug industries.

  7. The ferrous iron transporter FtrABCD is required for the virulence of Brucella abortus 2308 in mice.

    Science.gov (United States)

    Elhassanny, Ahmed E M; Anderson, Eric S; Menscher, Evan A; Roop, R Martin

    2013-06-01

    Iron transport has been linked to the virulence of Brucella strains in both natural and experimental hosts. The genes designated BAB2_0837-0840 in the Brucella abortus 2308 genome sequence are predicted to encode a CupII-type ferrous iron transporter homologous to the FtrABCD transporter recently described in Bordetella. To study the role of the Brucella FtrABCD in iron transport, an isogenic ftrA mutant was constructed from B. abortus 2308. Compared with the parental strain, the B. abortus ftrA mutant displays a decreased capacity to use non-haem iron sources in vitro, a growth defect in a low iron medium that is enhanced at pH 6, and studies employing radiolabelled FeCl3 confirmed that FtrABCD transports ferrous iron. Transcription of the ftrA gene is induced in B. abortus 2308 in response to iron deprivation and exposure to acid pH, and similar to other Brucella iron acquisition genes that have been examined the iron-responsiveness of ftrA is dependent upon the iron response regulator Irr. The B. abortus ftrA mutant exhibits significant attenuation in both cultured murine macrophages and experimentally infected mice, supporting the proposition that ferrous iron is a critical iron source for these bacteria in the mammalian host. © 2013 John Wiley & Sons Ltd.

  8. Bacteria-assisted preparation of nano α-Fe2O3 red pigment powders from waste ferrous sulfate

    International Nuclear Information System (INIS)

    Li, Xiang; Wang, Chuankai; Zeng, Yu; Li, Panyu; Xie, Tonghui; Zhang, Yongkui

    2016-01-01

    Highlights: • A route to prepare nano α-Fe 2 O 3 red pigment from waste ferrous sulfate is proposed. • Acidithiobacillus ferrooxidans is introduced for accelerating iron oxidation. • The particle size of synthetic α-Fe 2 O 3 is ranged from 22 nm to 86 nm. • The prepared nano α-Fe 2 O 3 red pigment fulfills ISO 1248-2006. - Abstract: Massive ferrous sulfate with excess sulfuric acid is produced in titanium dioxide industry each year, ending up stockpiled or in landfills as solid waste, which is hazardous to environment and in urgent demand to be recycled. In this study, waste ferrous sulfate was used as a second raw material to synthesize nano α-Fe 2 O 3 red pigment powders with a bacteria-assisted oxidation process by Acidithiobacillus ferrooxidans. The synthesis route, mainly consisting of bio-oxidation, precipitation and calcination, was investigated by means of titration, thermogravimetric analysis (TGA), X-ray diffraction (XRD), scanning electron microscope (SEM) and X-ray fluorescence (XRF) to obtain optimum conditions. Under the optimum conditions, nano α-Fe 2 O 3 red pigment powders contained 98.24 wt.% of Fe 2 O 3 were successfully prepared, with a morphology of spheroidal and particle size ranged from 22 nm to 86 nm and averaged at 45 nm. Moreover, the resulting product fulfilled ISO 1248-2006, the standards of iron oxide pigments.

  9. A comparative study of iron bioavailability from cocoa supplemented with ferric pyrophosphate or ferrous fumarate in rats.

    Science.gov (United States)

    Navas-Carretero, S; Sarriá, B; Pérez-Granados, A M; Schoppen, S; Izquierdo-Pulido, M; Vaquero, M P

    2007-01-01

    Food iron fortification can be a good strategy to prevent iron deficiency. Iron bioavailability from cocoa powder enriched with ferric pyrophosphate encapsulated in liposomes or ferrous fumarate was assessed in rats. Three groups of rats consumed during 28 days either a control diet or two diets prepared with ferric pyrophosphate- or ferrous fumarate-enriched cocoa powder as the unique source of iron. Body weight and food intake were monitored and last-week feces were collected. On day 28, animals were sacrificed and livers and spleens were removed. Hemoglobin and total iron binding capacity (TIBC) were determined. There were no significant differences in body weight and food intake. Apparent iron absorption and % absorption/intake were significantly lower in rats consuming enriched cocoa compared to the control group, without significant differences due to the iron form. Enriched cocoa groups showed significantly lower spleen iron content and concentration than the control. Liver iron was lower in the ferric pyrophosphate group compared to the other two groups. Hemoglobin and TIBC values showed a deficient iron status in ferric pyrophosphate rats. Cocoa powder is a good vehicle for iron fortification when enriched with ferrous fumarate compared to ferric pyrophosphate encapsulated in liposomes. Copyright 2007 S. Karger AG, Basel.

  10. Bioavailability of stabilised ferrous gluconate with glycine in fresh cheese matrix: a novel iron compound for food fortification.

    Science.gov (United States)

    Pizarro, Fernando; Boccio, José; Salgueiro, María; Olivares, Manuel; Carmuega, Esteban; Weill, Ricardo; Marque, Sebastien; Frereux, Marine; Noirt, Florence

    2013-03-01

    Iron fortification of foods continues to be one of the preferred ways of improving the iron status of the population. Dairy product is a common product in the diet; therefore, it is a plausible vehicle for iron fortification. This study aims to investigate the bioavailability of ferrous gluconate stabilised with glycine (FGSG) in a fresh cheese fortified with zinc. The iron bioavailability of fresh cheese fortified with either FGSG and with or without zinc and FGSG in aqueous solution and a water solution of ferrous ascorbate (reference dose) was studied using double radio iron ((55)Fe and (59)Fe) erythrocyte incorporation in 15 male subjects. All subjects presented with normal values for iron status parameters. The geometric mean of iron bioavailability for the water solution of FGSG was 38.2 %, adjusted to 40 % from reference doses (N.S.). Iron bioavailability in fresh cheese fortified with Ca and Zn was 15.4 % and was 23.1 % without Zn, adjusted to 40 % from reference doses (N.S.). The results of the present study show that the novel iron compound ferrous gluconate stabilised with glycine in a fresh cheese matrix is a good source of iron and can be used in iron fortification programmes.

  11. Contribution of nuclear analysis methods to the certification of BCR reference materials for non-metals in non-ferrous metals

    International Nuclear Information System (INIS)

    Pauwels, J.

    1979-01-01

    A number of reference materials for oxygen in different non-ferrous metals have been certified by BCR in the frame of a multidisciplinary Community project. The contribution of nuclear analysis methods is illustrated by several examples concerning the optimization of sample preparation techniques, the analysis of low and high oxygen non-ferrous metals and the extension of the program to other non-metals, especially nitrogen and carbon. (author)

  12. Rebuilding a Research Ethics Committee

    Science.gov (United States)

    Biggs, John S. G.; Marchesi, August

    2013-01-01

    The principal ethics committee in Australia's Capital, Canberra, underwent a major revision in the last three years based on changes debated in the literature. Committee or Board structure varies widely; regulations determining minimum size and membership differ between countries. Issues such as the effectiveness of committee management,…

  13. The Audit Committee. Board Basics

    Science.gov (United States)

    Ostrom, John S.

    2004-01-01

    The Effective Committees set of booklets comprises publications on the following committees: investment, buildings and grounds, academic affairs, student affairs, finance, development, trustees, audit, compensation, and executive. It is part of the AGB Board Basics Series. This report describes the primary role of an audit committee. The primary…

  14. Ferrous iron oxidation by sulfur-oxidizing Acidithiobacillus ferrooxidans and analysis of the process at the levels of transcription and protein synthesis.

    Science.gov (United States)

    Kucera, Jiri; Bouchal, Pavel; Lochman, Jan; Potesil, David; Janiczek, Oldrich; Zdrahal, Zbynek; Mandl, Martin

    2013-04-01

    In contrast to iron-oxidizing Acidithiobacillus ferrooxidans, A. ferrooxidans from a stationary phase elemental sulfur-oxidizing culture exhibited a lag phase in pyrite oxidation, which is similar to its behaviour during ferrous iron oxidation. The ability of elemental sulfur-oxidizing A. ferrooxidans to immediately oxidize ferrous iron or pyrite without a lag phase was only observed in bacteria obtained from growing cultures with elemental sulfur. However, these cultures that shifted to ferrous iron oxidation showed a low rate of ferrous iron oxidation while no growth was observed. Two-dimensional gel electrophoresis was used for a quantitative proteomic analysis of the adaptation process when bacteria were switched from elemental sulfur to ferrous iron. A comparison of total cell lysates revealed 39 proteins whose increase or decrease in abundance was related to this phenotypic switching. However, only a few proteins were closely related to iron and sulfur metabolism. Reverse-transcription quantitative PCR was used to further characterize the bacterial adaptation process. The expression profiles of selected genes primarily involved in the ferrous iron oxidation indicated that phenotypic switching is a complex process that includes the activation of genes encoding a membrane protein, maturation proteins, electron transport proteins and their regulators.

  15. Efficacy, Tolerability, and Acceptability of Iron Hydroxide Polymaltose Complex versus Ferrous Sulfate: A Randomized Trial in Pediatric Patients with Iron Deficiency Anemia

    Directory of Open Access Journals (Sweden)

    Beril Yasa

    2011-01-01

    Full Text Available Iron polymaltose complex (IPC offers similar efficacy with superior tolerability to ferrous sulfate in adults, but randomized trials in children are rare. In a prospective, open-label, 4-month study, 103 children aged >6 months with iron deficiency anemia (IDA were randomized to IPC once daily or ferrous sulfate twice daily, (both 5 mg iron/kg/day. Mean increases in Hb to months 1 and 4 with IPC were 1.2±0.9 g/dL and 2.3±1.3 g/dL, respectively, (both P=0.001 versus baseline and 1.8±1.7 g/dL and 3.0±2.3 g/dL with ferrous sulfate (both P=0.001 versus baseline (n.s. between groups. Gastrointestinal adverse events occurred in 26.9% and 50.9% of IPC and ferrous sulfate patients, respectively (P=0.012. Mean acceptability score at month 4 was superior with IPC versus ferrous sulfate (1.63±0.56 versus 2.14±0.75, P=0.001. Efficacy was comparable with IPC and ferrous sulfate over a four-month period in children with IDA, but IPC was associated with fewer gastrointestinal adverse events and better treatment acceptability.

  16. An investigation of wear behaviors of different Monel alloys produced by powder metallurgy

    Energy Technology Data Exchange (ETDEWEB)

    Esgin, U.; Özyürek, D. [Karabük University, Technology Faculty, Department of Manufacturing Engineering / Karabuk (Turkey); Kaya, H., E-mail: hasan.kaya@kocaeli.edu.tr [Kocaeli University, Asim Kocabiyik Vocational School of Higher Education, Department of Machine / Kocaeli (Turkey)

    2016-04-21

    In the present study, wear behaviors of Monel 400, Monel 404, Monel R-405 and Monel K-500 alloys produced by Powder Metallurgy (P/M) method were investigated. These compounds prepared from elemental powders were cold-pressed (600 MPa) and then, sintered at 1150°C for 2 hours and cooled down to the room temperature in furnace environment. Monel alloys produced by the P/M method were characterized through scanning electron microscope (SEM+EDS), X-ray diffraction (XRD), hardness and density measurements. In wear tests, standard pin-on-disk type device was used. Specimens produced within four different Monel Alloys were tested under 1ms{sup −1} sliding speed, under three different loads (20N, 30N and 40N) and five different sliding distances (400-2000 m). The results show that Monel Alloys have γ matrix and that Al{sub 0,9}Ni{sub 4,22} intermetallic phase was formed in the structure. Also, the highest hardness value was measured with the Monel K-500 alloy. In wear tests, the maximum weight loss according to the sliding distance, was observed in Monel 400 and Monel 404 alloys while the minimum weight loss was achieved by the Monel K-500 alloy.

  17. Compressibility of 304 Stainless Steel Powder Metallurgy Materials Reinforced with 304 Short Stainless Steel Fibers

    Directory of Open Access Journals (Sweden)

    Bibo Yao

    2016-03-01

    Full Text Available Powder metallurgy (P/M technique is usually used for manufacturing porous metal materials. However, some P/M materials are limitedly used in engineering for their performance deficiency. A novel 304 stainless steel P/M material was produced by a solid-state sintering of 304 stainless steel powders and 304 short stainless steel fibers, which were alternately laid in layers according to mass ratio. In this paper, the compressive properties of the P/M materials were characterized by a series of uniaxial compression tests. The effects of fiber content, compaction pressure and high temperature nitriding on compressive properties were investigated. The results indicated that, without nitriding, the samples changed from cuboid to cydariform without damage in the process of compression. The compressive stress was enhanced with increasing fiber content ranging from 0 to 8 wt.%. For compaction pressure from 55 to 75 MPa, greater compaction pressure improved compressive stress. Moreover, high temperature nitriding was able to significantly improve the yield stress, but collapse failure eventually occurred.

  18. Production of titanium alloys for advanced aerospace systems by powder metallurgy

    Directory of Open Access Journals (Sweden)

    Vinicius André Rodrigues Henriques

    2005-12-01

    Full Text Available Titanium alloys parts are ideally suited for advanced aerospace systems because of their unique combination of high specific strength at both room temperature and moderately elevated temperature, in addition to excellent corrosion resistance. Despite these features, use of titanium alloys in engines and airframes is limited by cost. The alloys processing by powder metallurgy eases the obtainment of parts with complex geometry. In this work, results of the Ti-6Al-4V and Ti-13Nb-13Zr alloys production are presented. Samples were produced by mixing of initial metallic powders followed by uniaxial and cold isostatic pressing with subsequent densification by sintering between 900 up to 1500 °C, in vacuum. Sintered samples were characterized for phase composition, microstructure and microhardness by X-ray diffraction, scanning electron microscopy and Vickers indentation, respectively. It was shown that the samples were sintered to high densities and presented homogeneous microstructure from the elements dissolution with low interstitial pick-up.

  19. Feasibility study of the production of biomedical Ti-6Al-4V alloy by powder metallurgy.

    Science.gov (United States)

    Bolzoni, L; Ruiz-Navas, E M; Gordo, E

    2015-04-01

    Titanium and its alloys are characterized by an exceptional combination of properties like high strength, good corrosion resistance and biocompatibility which makes them suitable materials for biomedical prosthesis and devices. The wrought Ti-6Al-4V alloy is generally favored in comparison to other metallic biomaterials due to its relatively low elastic modulus and it has been long used to obtain products for biomedical applications. In this work an alternative route to fabricate biomedical implants made out of the Ti-6Al-4V alloy is investigated. Specifically, the feasibility of the conventional powder metallurgy route of cold uniaxial pressing and sintering is addressed by considering two types of powders (i.e. blended elemental and prealloyed). The characterization of physical properties, chemical analysis, mechanical behavior and microstructural analysis is carried out in-depth and the properties are correlated among them. On the base of the results found, the produced alloys are promising materials for biomedical applications as well as cheaper surgical devices and tools. Copyright © 2015 Elsevier B.V. All rights reserved.

  20. Evaluation of the mechanical properties of powder metallurgy Ti-6Al-7Nb alloy.

    Science.gov (United States)

    Bolzoni, L; Ruiz-Navas, E M; Gordo, E

    2017-03-01

    Titanium and its alloys are common biomedical materials owing to their combination of mechanical properties, corrosion resistance and biocompatibility. Powder metallurgy (PM) techniques can be used to fabricate biomaterials with tailored properties because changing the processing parameters, such as the sintering temperature, products with different level of porosity and mechanical performances can be obtained. This study addresses the production of the biomedical Ti-6Al-7Nb alloy by means of the master alloy addition variant of the PM blending elemental approach. The sintering parameters investigated guarantee that the complete diffusion of the alloying elements and the homogenization of the microstructure is achieved. The sintering of the Ti-6Al-7Nb alloy induces a total shrinkage between 7.4% and 10.7% and the level of porosity decreases from 6.2% to 4.7% with the increment of the sintering temperature. Vickers hardness (280-300 HV30) and tensile properties (different combination of strength and elongation around 900MPa and 3%) are achieved. Copyright © 2016 Elsevier Ltd. All rights reserved.

  1. Hot alpha-emitting particles in residue of mining and metallurgy

    International Nuclear Information System (INIS)

    Freyer, K.; Treutler, H.C.; Weiss, H.; Ghose, R.; Selchau-Hansen, K.; Enge, W.

    1998-01-01

    Industrial residues of ore processing and metallurgy partly contain significant amounts of natural radionuclides. Such fine-grained, contaminated materials e.g. are scrubber dust slurry in the Mansfeld region, known as Theisenschlamm, and tailings of the uranium ore processing. The environmental significance of these materials in particular is related to the high mobility of its fine grain fractions by air and on the water path. By autoradiography using solid state nuclear track detectors the homogeneity of the distribution of alpha-emitting radionuclides in the above mentioned materials has been investigated. It has been found that beside a homogeneous background distribution of the alpha activity single spots with significant higher activity concentration exist in form of hot particles. Its concentration in different contaminated materials has been determined. A surfactant treatment process has been applied to separate uranium tailings material in different grain size fractions. The fractions have been characterized chemically, radiometrically and with respect to the amount of alpha-active hot particles. (orig.) [de

  2. Air Emissions of Selected Substances from Particular Sectors Including Metallurgy in Poland

    Directory of Open Access Journals (Sweden)

    Kargulewicz I.

    2017-03-01

    Full Text Available This article presents data on the anthropogenic air emissions of selected substances (CO2, SO2, total suspended particles (TSP, dioxins and furans (PCDD/F, Pb and Cd subject to reporting under the Climate Convention (UNFCCC or the Convention on Long-range Transboundary Air Pollution (UNECE CLRTAP. It also presents the national emissions of these substances in 2014 by the major source categories and defines the share of metal production in these emissions. Analysis is based on national emission inventory reports. Most important source of air emission in case of CO2 and SO2 is 1.A.1 Energy industries category. TSP and PCDD/F are emitted mainly from fuel combustion in small sources (i.a. households. Emission of heavy metals (Pb and Cd is connected mostly with 1.A.2. Manufacturing industries and construction category. Metallurgy is significant source of emission only for lead and cadmium from among all considered substances. The shares of particular sectors in the national emissions of given pollutants are important, in view of the possible reduction measures and the determination in which industries they could bring about tangible results.

  3. Physical Protection Study of the Radio metallurgy Installation Using SAVIComputer Program

    International Nuclear Information System (INIS)

    Pinitoyo, Andreas

    2000-01-01

    Based on IAEA Recommendation on INFCIR/225/Rev.3 (The Physical Protectionof Nuclear Material), a nuclear installation shall have physical protectionsystem for protection or being secure on sabotage activities in theinstallation and thieve of nuclear materials. The recommendation states therequirements for physical protection of nuclear materials usage, transit andstorage. Radio metallurgy Installation of the Fuel Element and ReprocessingDevelopment Center (BATAN) at Serpong is a nuclear installation for researchon post irradiation of high radioactive spent fuel element, its processingand storage. The installation has risk on threat of a sabotage, which isdominant than thieve. The RMI building was designed and constructed ofphysical protection components and have been integrated with the BATAN Safetyand Security System and the Security Guards functions to be PhysicalProtection System for the RMI. By using the SAVI Computer Program with inputdata from the existing standards, assumptions for detection possibility,delay and response, that will result the probability of interruptions of theworst adversary paths PI = 0.1. These mean that the physical protectionsystems of the RMI shall be upgraded and improved in order to be reliable orbetter if the most of paths to the target PI = 1.0. (author)

  4. Fabrication of Fe-Cr-Mo powder metallurgy steel via a mechanical-alloying process

    Science.gov (United States)

    Park, Jooyoung; Jeong, Gowoon; Kang, Singon; Lee, Seok-Jae; Choi, Hyunjoo

    2015-11-01

    In this study, we employed a mechanical-alloying process to manufacture low-alloy CrL and CrM steel powders that have similar specifications to their water-atomized counterparts. X-ray diffraction showed that Mo and Cr are alloyed in Fe after four cycles of planetary milling for 1 h at 150 RPM with 15-min pauses between the cycles (designated as P2C4 process). Furthermore, the measured powder size was found to be similar to that of the water-atomized counterparts according to both scanning electron microscope images and laser particle size analysis. The samples were sintered at 1120 °C, after which the P2C4-milled CrL showed similar hardness to that of water-atomized CrL, whereas the P2C4-milled CrM showed about 45% lower hardness than that of its water-atomized counterpart. Water-atomized CrM consists of a well-developed lathtype microstructure (bainite or martensite), while a higher fraction of polygonal ferrite is observed in P2C4-milled CrM. This phase difference causes the reduction of hardness in the P2C4-milled CrM, implying that the phase transformation behavior of specimens produced via powder metallurgy is influenced by the powder fabrication method.

  5. Bridging the gap between metallurgy and fatigue reliability of hydraulic turbine runners

    International Nuclear Information System (INIS)

    Thibault, D; Gagnon, M; Godin, S

    2014-01-01

    The failure of hydraulic turbine runners is a very rare event. Hence, in order to assess the reliability of these components, one cannot rely on statistical models based on the number of failures in a given population. However, as there is a limited number of degradation mechanisms involved, it is possible to use physically-based reliability models. Such models are more complicated but have the advantage of being able to account for physical parameters in the prediction of the evolution of runner degradation. They can therefore propose solutions to help improve reliability. With the use of such models, the effect of materials properties on runner reliability can easily be illustrated. This paper will present a brief review of the Kitagawa-Takahashi diagram that links the damage tolerance approach, based on fracture mechanics, to the stress or strain-life approaches. This diagram is at the centre of the reliability model used in this study. Using simplified response spectra obtained from on-site runner stress measurements, the paper will show how fatigue reliability is impacted by materials fatigue properties, namely fatigue crack propagation behaviour and fatigue limit obtained on S-N curves. It will also present a review of the most important microstructural features of 13%Cr- 4%Ni stainless steels used for runner manufacturing and will review how they influence fatigue properties in an effort to bridge the gap between metallurgy and turbine runners reliability

  6. Reuse of beneficiency residue from mining and metallurgy as source of zeolites

    International Nuclear Information System (INIS)

    Souza, J.A.S.; Rodrigues, E.C.; Souza, J.A.S.; Neves, R.F.; Macedo, E.N.; Moraes, C.G.

    2011-01-01

    The mining industry and metallurgy, located in Para State, brought the concern about the huge generation of solid waste (eg The Red Mud (LV) industry Alumina; waste alumina sand-kaolin industry, waste of cuba electrolytic aluminum industry and other metal) and with the gas emissions from the burning of fossil fuels these industries. In the case of solid waste, most of which require special care such as check dams and even storage areas protected. Since the waste gases are not always properly treated and are one of the most discussed environmental problem today, according to the emission of compounds such as SOx, NOx, Cox's treatment of these effluents should be given, necessarily involves techniques of adsorption followed by reaction neutralization. These techniques can be used in two ways: by wet and dry. In the specific case of gas emissions from fossil fuels is used to wash using aqueous suspensions of calcium oxide. In this context, studies conducted in the Laboratory of Ceramic Materials, UFPA [1, 2], showed that the Bayer process residue (red mud) has characteristics that indicate the possibility of its use in place of calcium oxide in the treatment of waste gases. Moreover, waste from kaolin industry can be used as adsorbents since they go through a process of synthesis, producing different types of synthetic zeolites can be extremely useful in the treatment of waste and various activities related to environmental issues. (author)

  7. Innovative technologies for powder metallurgy-based disk superalloys: Progress and proposal

    Science.gov (United States)

    Chong-Lin, Jia; Chang-Chun, Ge; Qing-Zhi, Yan

    2016-02-01

    Powder metallurgy (PM) superalloys are an important class of high temperature structural materials, key to the rotating components of aero engines. In the purview of the present challenges associated with PM superalloys, two novel approaches namely, powder preparation and the innovative spray-forming technique (for making turbine disk) are proposed and studied. Subsequently, advanced technologies like electrode-induction-melting gas atomization (EIGA), and spark-plasma discharge spheroidization (SPDS) are introduced, for ceramic-free superalloy powders. Presently, new processing routes are sought after for preparing finer and cleaner raw powders for disk superalloys. The progress of research in spray-formed PM superalloys is first summarized in detail. The spray-formed superalloy disks specifically exhibit excellent mechanical properties. This paper reviews the recent progress in innovative technologies for PM superalloys, with an emphasis on new ideas and approaches, central to the innovation driving techniques like powder processing and spray forming. Project supported by the National Natural Science Foundation of China (Grant Nos. 50974016 and 50071014).

  8. The Promotion of Liquid Phase Sintering of Boron-Containing Powder Metallurgy Steels by Adding Nickel

    Directory of Open Access Journals (Sweden)

    Wu Ming-Wei

    2015-01-01

    Full Text Available Boron is a feasible alloying element for liquid phase sintering (LPS of powder metallurgy (PM steels. This study investigated the effect of nickel (Ni, which is widely used in PM steels, on the liquid phase sintering of boron-containing PM steels. The results showed that the addition of 1.8wt% Ni does not apparently modify the LPS mechanism of boron-containing PM steels. However, adding 1.8wt% Ni slightly improves the LPS densification from 0.60 g/cm3 to 0.65 g/cm3, though the green density is reduced. Thermodynamic simulation demonstrated that the presence of Ni lowers the temperature region of liquid formation, resulting in enhanced LPS densification. Moreover, original graphite powders remains in the steels sintered at 1200 ºC. These graphite powders mostly dissolve into the base iron powder when the sintering temperature is increased from 1200 ºC to 1250 ºC.

  9. Emissions from Pre-Hispanic Metallurgy in the South American Atmosphere

    Science.gov (United States)

    De Vleeschouwer, François; Vanneste, Heleen; Mauquoy, Dmitri; Piotrowska, Natalia; Torrejón, Fernando; Roland, Thomas; Stein, Ariel; Le Roux, Gaël

    2014-01-01

    Metallurgical activities have been undertaken in northern South America (NSA) for millennia. However, it is still unknown how far atmospheric emissions from these activities have been transported. Since the timing of metallurgical activities is currently estimated from scarce archaeological discoveries, the availability of reliable and continuous records to refine the timing of past metal deposition in South America is essential, as it provides an alternative to discontinuous archives, as well as evidence for global trace metal transport. We show in a peat record from Tierra del Fuego that anthropogenic metals likely have been emitted into the atmosphere and transported from NSA to southern South America (SSA) over the last 4200 yrs. These findings are supported by modern time back-trajectories from NSA to SSA. We further show that apparent anthropogenic Cu and Sb emissions predate any archaeological evidence for metallurgical activities. Lead and Sn were also emitted into the atmosphere as by-products of Inca and Spanish metallurgy, whereas local coal-gold rushes and the industrial revolution contributed to local contamination. We suggest that the onset of pre-Hispanic metallurgical activities is earlier than previously reported from archaeological records and that atmospheric emissions of metals were transported from NSA to SSA. PMID:25353346

  10. Characterization of TiC-FeCrMn Cermets Produced by Powder Metallurgy Method

    Directory of Open Access Journals (Sweden)

    Märt Kolnes

    2015-09-01

    Full Text Available TiC-NiMo cermets combine relatively low density with high hardness. Because nickel is known as a toxin and allergen and allergy to nickel is a phenomenon which has assumed growing importance in recent years there has been a flurry of activity to find alternatives to the nickel binder in cermets. It is also the global research and technical development trend in the powder metallurgy cermets industry. In present research TiC-based cermets with FeCrMn binder system were fabricated. Three different sintering conditions were used (vacuum sintering, sinter/HIP and sintering under low Ar pressure. Because of high vapor pressure of manganese different sintering conditions and technologies were investigated to depress the Mn-loss during sintering. Chemical composition of TiC-FeCrMn cermets after different sintering conditions were analyzed by energy-dispersive X-ray spectroscopy (EDS and mechanical properties – hardness and fracture toughness were evaluated on the samples. Results of research showed that Ni-free TiC-based CrMn-steels bonded cermets compare unfavorably with cermets bonded with CrNi austenitic steels in terms of fracture toughness and corrosion resistance. Noticeable Mn-loss during vacuum sintering can be avoided when sintering under low Ar gas pressure.DOI: http://dx.doi.org/10.5755/j01.ms.21.3.7364

  11. Titanium nitride deposition in titanium implant alloys produced by powder metallurgy

    International Nuclear Information System (INIS)

    Henriques, V.A.R.; Cairo, C.A.A.; Faria, J.; Lemos, T.G.; Galvani, E.T.

    2009-01-01

    Titanium nitride (TiN) is an extremely hard material, often used as a coating on titanium alloy, steel, carbide, and aluminum components to improve wear resistance. Electron Beam Physical Vapor Deposition (EB-PVD) is a form of deposition in which a target anode is bombarded with an electron beam given off by a charged tungsten filament under high vacuum, producing a thin film in a substrate. In this work are presented results of TiN deposition in targets and substrates of Ti (C.P.) and Ti- 13 Nb- 13 Zr obtained by powder metallurgy. Samples were produced by mixing of hydride metallic powders followed by uniaxial and cold isostatic pressing with subsequent densification by sintering between 900°C up to 1400 °C, in vacuum. The deposition was carried out under nitrogen atmosphere. Sintered samples were characterized for phase composition, microstructure and microhardness by X-ray diffraction, scanning electron microscopy and Vickers indentation, respectively. It was shown that the samples were sintered to high densities and presented homogeneous microstructure, with ideal characteristics for an adequate deposition and adherence. The film layer presented a continuous structure with 15μm. (author)

  12. Emissions from pre-Hispanic metallurgy in the South American atmosphere.

    Directory of Open Access Journals (Sweden)

    François De Vleeschouwer

    Full Text Available Metallurgical activities have been undertaken in northern South America (NSA for millennia. However, it is still unknown how far atmospheric emissions from these activities have been transported. Since the timing of metallurgical activities is currently estimated from scarce archaeological discoveries, the availability of reliable and continuous records to refine the timing of past metal deposition in South America is essential, as it provides an alternative to discontinuous archives, as well as evidence for global trace metal transport. We show in a peat record from Tierra del Fuego that anthropogenic metals likely have been emitted into the atmosphere and transported from NSA to southern South America (SSA over the last 4200 yrs. These findings are supported by modern time back-trajectories from NSA to SSA. We further show that apparent anthropogenic Cu and Sb emissions predate any archaeological evidence for metallurgical activities. Lead and Sn were also emitted into the atmosphere as by-products of Inca and Spanish metallurgy, whereas local coal-gold rushes and the industrial revolution contributed to local contamination. We suggest that the onset of pre-Hispanic metallurgical activities is earlier than previously reported from archaeological records and that atmospheric emissions of metals were transported from NSA to SSA.

  13. Emissions from pre-Hispanic metallurgy in the South American atmosphere.

    Science.gov (United States)

    De Vleeschouwer, François; Vanneste, Heleen; Mauquoy, Dmitri; Piotrowska, Natalia; Torrejón, Fernando; Roland, Thomas; Stein, Ariel; Le Roux, Gaël

    2014-01-01

    Metallurgical activities have been undertaken in northern South America (NSA) for millennia. However, it is still unknown how far atmospheric emissions from these activities have been transported. Since the timing of metallurgical activities is currently estimated from scarce archaeological discoveries, the availability of reliable and continuous records to refine the timing of past metal deposition in South America is essential, as it provides an alternative to discontinuous archives, as well as evidence for global trace metal transport. We show in a peat record from Tierra del Fuego that anthropogenic metals likely have been emitted into the atmosphere and transported from NSA to southern South America (SSA) over the last 4200 yrs. These findings are supported by modern time back-trajectories from NSA to SSA. We further show that apparent anthropogenic Cu and Sb emissions predate any archaeological evidence for metallurgical activities. Lead and Sn were also emitted into the atmosphere as by-products of Inca and Spanish metallurgy, whereas local coal-gold rushes and the industrial revolution contributed to local contamination. We suggest that the onset of pre-Hispanic metallurgical activities is earlier than previously reported from archaeological records and that atmospheric emissions of metals were transported from NSA to SSA.

  14. Deformation and energy absorption properties of powder-metallurgy produced Al foams

    International Nuclear Information System (INIS)

    Michailidis, N.; Stergioudi, F.; Tsouknidas, A.

    2011-01-01

    Highlights: → Porous Al fabricated via a dissolution and sintering method using raw cane sugar. → Different deformation mode depending on the relative density of the foams. → Enhanced energy absorption by reducing pore size and relative density of the foam. → Pore size uniformity and sintering temperature affect energy absorption. - Abstract: Al-foams with relative densities ranging from 0.30 to 0.60 and mean pore sizes of 0.35, 0.70 and 1.35 mm were manufactured by a powder metallurgy technology, based on raw cane sugar as a space-holder material. Compressive tests were carried out to investigate the deformation and energy absorbing characteristics and mechanisms of the produced Al-foams. The deformation mode of low density Al-foams is dominated by the bending and buckling of cell walls and the formation of macroscopic deformation bands whereas that of high density Al-foams is predominantly attributed to plastic yielding. The energy absorbing capacity of Al-foams rises for increased relative density and compressive strength. The sintering temperature of Al-foams having similar relative densities has a marked influence on both, energy absorbing efficiency and capacity. Pore size has a marginal effect on energy efficiency aside from Al-foams with mean pore size of 0.35 which exhibit enhanced energy absorption as a result of increased friction during deformation at lower strain levels.

  15. Microstructurally sensitive crack nucleation around inclusions in powder metallurgy nickel-based superalloys

    International Nuclear Information System (INIS)

    Jiang, J.; Yang, J.; Zhang, T.; Zou, J.; Wang, Y.; Dunne, F.P.E.; Britton, T.B.

    2016-01-01

    Nickel-based superalloys are used in high strength, high-value applications, such as gas turbine discs in aero engines. In these applications the integrity of the disc is critical and therefore understanding crack initiation mechanisms is of high importance. With an increasing trend towards powder metallurgy routes for discs, sometimes unwanted non-metallic inclusions are introduced during manufacture. These inclusions vary in size from ∼10 μm to 200 μm which is comparable to the grain size of the nickel-based superalloys. Cracks often initiate near these inclusions, and the precise size, shape, location and path of these cracks are microstructurally sensitive. In this study, we focus on crack initiation at the microstructural length scale using a controlled three-point bend test, with the inclusion deliberately located within the tensile fibre of the beam. Electron backscatter diffraction (EBSD) is combined with high spatial resolution digital image correlation (HR-DIC) to explore full field plastic strain distributions, together with finite element modelling, to understand the micro-crack nucleation mechanisms. This full field information and controlled sample geometry enable us to systematically test crack nucleation criteria. We find that a combined stored energy and dislocation density provide promising results. These findings potentially facilitate more reliable and accurate lifing prediction tools to be developed and applied to engineering components. - Highlights: • High resolution digital image correlation. • High resolution electron backscatter diffraction. • Crack nucleation. • Non-metallic inclusion.

  16. Power-law creep of powder-metallurgy grade molybdenum sheet

    International Nuclear Information System (INIS)

    Ciulik, J.; Taleff, E.M.

    2007-01-01

    Creep behavior of commercial-purity, powder-metallurgy grade molybdenum (Mo) sheet has been investigated at temperatures between 1300 and 1600 deg. C (0.56-0.63 T m ) using tensile testing at controlled strain rates. Strain-rate-change tests were performed at constant-temperatures over true-strain rates from 1.0 x 10 -6 to 5.0 x 10 -4 s -1 . Results agree with previously published data indicating that Mo follows power-law creep with a stress exponent of about 5; however, the present results address a temperature range not previously documented. The activation energy for creep was determined to be 240 kJ/mol within this temperature range, which is lower than previously published values and approximately half the value reported for self-diffusion, indicating that diffusion mechanisms faster than lattice diffusion are active. It is shown that Mo creep data from a variety of investigations converge closely to a single line on a master plot of strain rate normalized using an activation energy of 240 kJ/mol when plotted against stress normalized by the temperature-dependent elastic modulus. This activation energy for creep is attributed to an effective diffusivity that fits the creep data obtained during this study as well as from previously published creep data from commercial-purity molybdenum

  17. The substitution of nickel for cobalt in hot isostatically pressed powder metallurgy UDIMET 700 alloys

    Science.gov (United States)

    Harf, F. H.

    1985-01-01

    Nickel was substituted in various proportions for cobalt in a series of five hot-isostatically-pressed powder metallurgy alloys based on the UDIMET 700 composition. These alloys were given 5-step heat treatments appropriate for use in turbine engine disks. The resultant microstructures displayed three distinct sizes of gamma-prime particles in a gamma matrix. The higher cobalt-content alloys contained larger amounts of the finest gamma-prime particles, and had the lowest gamma-gamma-prime lattice mismatch. While all alloys had approximately the same tensile properties at 25 and 650 gamma C, the rupture lives at 650 and 760 C peaked in the alloys with cobalt contents between 12.7 and 4.3 pct. Minimum creep rates increased as cobalt contents were lowered, suggesting their correlation with the gamma-prime particle size distribution and the gamma-gamma-prime mismatch. It was also found that, on overaging at temperatures higher than suitable for turbine disk use, the high cobalt-content alloys were prone to sigma phase formation.

  18. State-of-the-art of recycling e-wastes by vacuum metallurgy separation.

    Science.gov (United States)

    Zhan, Lu; Xu, Zhenming

    2014-12-16

    In recent era, more and more electric and electronic equipment wastes (e-wastes) are generated that contain both toxic and valuable materials in them. Most studies focus on the extraction of valuable metals like Au, Ag from e-wastes. However, the recycling of metals such as Pb, Cd, Zn, and organics has not attracted enough attentions. Vacuum metallurgy separation (VMS) processes can reduce pollution significantly using vacuum technique. It can effectively recycle heavy metals and organics from e-wastes in an environmentally friendly way, which is beneficial for both preventing the heavy metal contaminations and the sustainable development of resources. VMS can be classified into several methods, such as vacuum evaporation, vacuum carbon reduction and vacuum pyrolysis. This paper respectively reviews the state-of-art of these methods applied to recycling heavy metals and organics from several kinds of e-wastes. The method principle, equipment used, separating process, optimized operating parameters and recycling mechanism of each case are illustrated in details. The perspectives on the further development of e-wastes recycling by VMS are also presented.

  19. Anodization Mechanism on SiC Nanoparticle Reinforced Al Matrix Composites Produced by Power Metallurgy.

    Science.gov (United States)

    Ferreira, Sonia C; Conde, Ana; Arenas, María A; Rocha, Luis A; Velhinho, Alexandre

    2014-12-19

    Specimens of aluminum-based composites reinforced by silicon carbide nanoparticles (Al/SiC np ) produced by powder metallurgy (PM) were anodized under voltage control in tartaric-sulfuric acid (TSA). In this work, the influence of the amount of SiC np on the film growth during anodizing was investigated. The current density versus time response and the morphology of the porous alumina film formed at the composite surface are compared to those concerning a commercial aluminum alloy (AA1050) anodized under the same conditions. The processing method of the aluminum alloys influences the efficiency of the anodizing process, leading to a lower thicknesses for the unreinforced Al-PM alloy regarding the AA1050. The current density versus time response is strongly dependent on the amount of SiC np . The current peaks and the steady-state current density recorded at each voltage step increases with the SiC np volume fraction due to the oxidation of the SiC np . The formation mechanism of the anodic film on Al/SiC np composites is different from that occurring in AA1050, partly due the heterogeneous distribution of the reinforcement particles in the metallic matrix, but also to the entrapment of SiC np in the anodic film.

  20. Factors Influencing Dwell Fatigue Cracking in Notches of Powder Metallurgy Superalloys

    Science.gov (United States)

    Gabb, T. P.; Telesman, J.; Ghosn, L.; Garg, A.; Gayda, J.

    2011-01-01

    The influences of heat treatment and cyclic dwells on the notch fatigue resistance of powder metallurgy disk superalloys were investigated for low solvus high refractory (LSHR) and ME3 disk alloys. Disks were processed to produce material conditions with varied microstructures and associated mechanical properties. Notched specimens were first subjected to baseline dwell fatigue cycles having a dwell at maximum load, as well as tensile, stress relaxation, creep rupture, and dwell fatigue crack growth tests at 704 C. Several material heat treatments displayed a bimodal distribution of fatigue life with the lives varying by two orders-of-magnitude, while others had more consistent fatigue lives. This response was compared to other mechanical properties, in search of correlations. The wide scatter in baseline dwell fatigue life was observed only for material conditions resistant to stress relaxation. For selected materials and conditions, additional tests were then performed with the dwells shifted in part or in total to minimum tensile load. The tests performed with dwells at minimum load exhibited lower fatigue lives than max dwell tests, and also exhibited early crack initiation and a substantial increase in the number of initiation sites. These results could be explained in part by modeling evolution of peak stresses in the notch with continued dwell fatigue cycling. Fatigue-environment interactions were determined to limit life for the fatigue cycles with dwells.

  1. Study on titanium-magnesium composites with bicontinuous structure fabricated by powder metallurgy and ultrasonic infiltration.

    Science.gov (United States)

    Jiang, S; Huang, L J; An, Q; Geng, L; Wang, X J; Wang, S

    2018-02-14

    Titanium-magnesium (Ti-Mg) composites with bicontinuous structure have been successfully fabricated by powder metallurgy and ultrasonic infiltration for biomaterial potential. In the composites, Ti phase is distributed continuously by sintering necks, while Mg phase is also continuous, distributing at the interconnected pores surrounding the Ti phase. The results showed that the fabricated Ti-Mg composites exhibited low modulus and high strength, which are very suitable for load bearing biomedical materials. The composites with 100 µm and 230 µm particle sizes exhibited Young's modulus of 37.6 GPa and 23.4 GPa, 500.7 MPa and 340 MPa of compressive strength and 631.5 MPa and 375.2 MPa of bending strength, respectively. Moreover, both of the modulus and strength of the composites increase with decreasing of Ti particle sizes. In vitro study has been done for the preliminary evaluation of the Ti-Mg composites. Copyright © 2018 Elsevier Ltd. All rights reserved.

  2. Compressibility of 304 Stainless Steel Powder Metallurgy Materials Reinforced with 304 Short Stainless Steel Fibers.

    Science.gov (United States)

    Yao, Bibo; Zhou, Zhaoyao; Duan, Liuyang; Xiao, Zhiyu

    2016-03-04

    Powder metallurgy (P/M) technique is usually used for manufacturing porous metal materials. However, some P/M materials are limitedly used in engineering for their performance deficiency. A novel 304 stainless steel P/M material was produced by a solid-state sintering of 304 stainless steel powders and 304 short stainless steel fibers, which were alternately laid in layers according to mass ratio. In this paper, the compressive properties of the P/M materials were characterized by a series of uniaxial compression tests. The effects of fiber content, compaction pressure and high temperature nitriding on compressive properties were investigated. The results indicated that, without nitriding, the samples changed from cuboid to cydariform without damage in the process of compression. The compressive stress was enhanced with increasing fiber content ranging from 0 to 8 wt.%. For compaction pressure from 55 to 75 MPa, greater compaction pressure improved compressive stress. Moreover, high temperature nitriding was able to significantly improve the yield stress, but collapse failure eventually occurred.

  3. Residual Stresses in a NiCrY-Coated Powder Metallurgy Disk Superalloy

    Science.gov (United States)

    Gabb, Timothy P.; Rogers, Richard B.; Nesbitt, James A.; Puleo, Bernadette J.; Miller, Robert A.; Telesman, Ignacy; Draper, Susan L.; Locci, Ivan E.

    2017-01-01

    Protective ductile coatings will be necessary to mitigate oxidation and corrosion attack on superalloy disks exposed to increasing operating temperatures in some turbine engine environments. However, such coatings must be resistant to harmful surface cracking during service. The objective of this study was to investigate how residual stresses evolve in such coatings. Cylindrical gage fatigue specimens of powder metallurgy-processed disk superalloy LSHR were coated with a NiCrY coating, shot peened, and then subjected to fatigue in air at room and high temperatures. The effects of shot peening and fatigue cycling on average residual stresses and other aspects of the coating were assessed. Shot peening did induce beneficial compressive residual stresses in the coating and substrate. However, these stresses became more tensile in the coating with subsequent heating and contributed to cracking of the coating in long intervals of cycling at 760 C. Substantial compressive residual stresses remained in the substrate adjacent to the coating, sufficient to suppress fatigue cracking. The coating continued to protect the substrate from hot corrosion pitting, even after fatigue cracks initiated in the coating.

  4. Dwell Notch Low Cycle Fatigue Behavior of a Powder Metallurgy Nickel Disk Alloy

    Science.gov (United States)

    Telesman, J.; Gabb, T. P.; Yamada, Y.; Ghosn, L. J.; Jayaraman, N.

    2012-01-01

    A study was conducted to determine the processes which govern dwell notch low cycle fatigue (NLCF) behavior of a powder metallurgy (P/M) ME3 disk superalloy. The emphasis was placed on the environmentally driven mechanisms which may embrittle the highly stressed notch surface regions and reduce NLCF life. In conjunction with the environmentally driven notch surface degradation processes, the visco-plastic driven mechanisms which can significantly change the notch root stresses were also considered. Dwell notch low cycle fatigue testing was performed in air and vacuum on a ME3 P/M disk alloy specimens heat treated using either a fast or a slow cooling rate from the solutioning treatment. It was shown that dwells at the minimum stress typically produced a greater life debit than the dwells applied at the maximum stress, especially for the slow cooled heat treatment. Two different environmentally driven failure mechanisms were identified as the root cause of early crack initiation in the min dwell tests. Both of these failure mechanisms produced mostly a transgranular crack initiation failure mode and yet still resulted in low NLCF fatigue lives. The lack of stress relaxation during the min dwell tests produced higher notch root stresses which caused early crack initiation and premature failure when combined with the environmentally driven surface degradation mechanisms. The importance of environmental degradation mechanisms was further highlighted by vacuum dwell NLCF tests which resulted in considerably longer NLCF lives, especially for the min dwell tests.

  5. STUDY OF THE IMPACT OF PHOSPHOGYPSUM ADDITIVE AND FERROUS SULPHATE SOLUTION ON THE MECHANISM OF THE MAGNESIA-BISHOFIT COMPOSITION

    Directory of Open Access Journals (Sweden)

    DEREVIANKO V. N.

    2015-11-01

    Full Text Available Problem statement. Phosphogypsum is a very pure raw material [16] with a negative, from a technical point of view, elongated shape of calcium dihydrate crystals (due to the formation conditions, which remains the same after both dehydration in dry air and grinding, this makes technical difficulties relating to further processing of the product into a binder, consequently, water resistance and plasticity of magnesium solutions can be improved by adding primary and secondary phosphates without strength reduction. Famous experts on phosphogypsum Yu. P. Meshcheryakov and N. A. Kolev [8] found, that when adding phosphogypsum instead of natural gypsum during grinding of Portland cement, which is intended to control the setting time of the mixture, there occurred reduction in the initial setting time from 1 h 55 min up to 1 h 36 min (when adding 4 % agent, and the final setting time was decreased from 6 h 15 min up to 6 min. After grinding of phosphogypsum, there appeared a fresh surface, on which the electron emission phenomenon occurs, however, not the entire surface emits, but only the active centres, where field strength reaches 108 V/cm. The positively charged active centres have low CaSO4 2H2O concentration on their surface. Purpose. Specifying the optimal amount of phosphogypsum and ferrous sulphate solution added, studying their impact on the curing mechanism of the magnesia-bishofit composition. Conclusion. To increase the sulphate compound, required for the crystallinity [10] reduction and magnesia stone sealing [4], the ferrous sulphate solution have been added to the composition formulation, ferrous sulphate anions immediately polarize free calcium ions with the formation of CaSO4∙2H2O. P. P. Budkov's experiments [8] prove that the larger the magnesia cement-to-sulphate stone ratio, the lower the setting time of the composition, and the higher the tensile strength of the stone. Moreover, V. V. Shchelyaghin [15] recommended adding ferrous

  6. Ferrous sulphate mono and heptahydrate reduction of hexavalent chromium in cement: effectiveness and storability

    Directory of Open Access Journals (Sweden)

    Valverde, J. L.

    2005-09-01

    Full Text Available In Community legislation, substances containing hexavalent chromium are classified as carcinogenic, mutagenic and sensitizing. In cement, hexavalent chromium intensifies sensitization and may set off severe allergic reactions in workers in routine contact with the product, whether in the factory or on construction sites. The allergic or contact dermatitis causes is a very painful disease that may lead to permanent worker disability. According to Directive 2003/53/EC of the European Parliament and the Council, Governments of all member countries will be required to prohibit the marketing and use, as of 17 January 2005, of any cement or cement preparation containing more than 2 ppm of chromium (VI. Hexavalent chromium can be reduced with ferrous sulphate to trivalent chromium, which is water-insoluble and therefore innocuous to the skin. The present paper reports the effects of adding ferrous sulphate mono- or heptahydrate to a commercial cement and the storage time of the mix on the concentration of hexavalent chromium. The salts studied were found to effectively reduce hexavalent chromium in cement for at least three months.

    Las sustancias que contienen cromo hexavalente están clasificadas en la legislación comunitaria como sustancias carcinogénicas, mutagénicas y sensibilizantes. El cromo hexavalente del cemento potencia la sensibilización y provoca graves reacciones alérgicas que sufren bastante a menudo los trabajadores que lo manipulan habitualmente, ya sea en fábrica o en el sector de la construcción. La dermatitis alérgica o de contacto que produce es muy dolorosa y puede dejar a los trabajadores en estado de discapacidad. La Directiva 2003/53/CE del Parlamento Europeo y del Consejo, exige a los Gobiernos de los países miembros, que a partir del 17 de enero de 2005, prohiban el uso y la comercialización de todos aquellos cementos y preparados que contengan cemento, cuyo contenido en cromo (VI soluble, una vez hidratados

  7. Standing Concertation Committee

    CERN Document Server

    HR Department

    2009-01-01

    The main items discussed at the meetings of the Standing Concertation Committee in the first quarter of 2009 included: Merit Appraisal and Recognition Scheme (MARS) 2009 exercise The committee took note of 2009 MARS ceiling guidelines giving the advancement budget by career path and amounting to approx 1.80% of the basic salary bill. To this will be added 250 steps CERN-wide, financed by savings from implementation of the international indemnity for 2007, 2008 and the first half of 2009. The specific Senior Staff Guidelines, including the proposed number of promotions from Career Path E to F, were also noted. The guidelines with respect to step distribution were also noted: the minima and maxima remain the same as in previous years. Compliance with the guidelines will continue to be monitored closely (more details, including a frequently asked questions section). It was also noted that Financial Awards (awards for extraordinary service and responsibility allowances) may b...

  8. Standing Concertation Committee

    CERN Multimedia

    HR Department

    2009-01-01

    Ordinary Meeting on 11 May 2009 The meeting of the Standing Concertation Committee held on 11 May 2009 was entirely dedicated to the preparation of the TREF meeting on 19 & 20 May 2009. The Committee took note, discussed and agreed on some clarifications on a number of documents and presentations that the Management planned to submit and/or present to TREF on the following subjects: • Personnel statistics 2008: J. Purvis presented the Personnel Statistics for 2008 prepared by HR Department. In line with the previous year, key messages were firstly, a general reduction in staff (2544 to 2400, - 6%), secondly, a reduction in administrative services personnel (from 422 to 387, - 8%) and thirdly, a marked increase in the number of Users and Unpaid Associates (from 8369 to 9140, + 9%) • Five-Yearly Review 2010: A series of draft documents were submitted for discussion, comprising an introductory document explaining the statutory basis for the following four document...

  9. Committees and sponsors

    Science.gov (United States)

    2011-10-01

    International Advisory Committee Richard F CastenYale, USA Luiz Carlos ChamonSão Paulo, Brazil Osvaldo CivitareseLa Plata, Argentina Jozsef CsehATOMKI, Hungary Jerry P DraayerLSU, USA Alfredo Galindo-UribarriORNL & UT, USA James J KolataNotre Dame, USA Jorge López UTEP, USA Joseph B NatowitzTexas A & M, USA Ma Esther Ortiz IF-UNAM Stuart PittelDelaware, USA Andrés SandovalIF-UNAM Adam SzczepaniakIndiana, USA Piet Van IsackerGANIL, France Michael WiescherNotre Dame, USA Organizing Committee Libertad Barrón-Palos (Chair)IF-UNAM Roelof BijkerICN-UNAM Ruben FossionICN-UNAM David LizcanoININ Sponsors Instituto de Ciencias Nucleares, UNAMInstituto de Física, UNAMInstituto Nacional de Investigaciones NuclearesDivisión de Física Nuclear de la SMFCentro Latinoamericano de Física

  10. Analysis of Chemical Composition of Non-Ferrous Metal Items from the Ananyino Burial Ground

    Directory of Open Access Journals (Sweden)

    Saprykina Irina А.

    2016-03-01

    Full Text Available The article presents results of an analysis conducted by the authors in order to study chemical composition of items from non-ferrous metals found on the Ananyino burial ground. A number of research methods, including OES, XRF and TXRF was applied to study a selection of 387 samples of arrow- and spearheads, celts, tail-pieces, warhammers, poleaxes, knives and daggers, as well as items of attire and jewelry, some sporadic details of harness and bridle. The fi ndings are quite comparable. The results were classifi ed by the geochemical principle of 1,0% alloyage threshold. It was found out that the sample primarily consists of copper items, including “pure” copper and copper with a wide range of trace elements (particularly, Ni, As, Sb. The core (48% consists of copper items with traces of antimony and arsenic, or “pure” copper (7%, tin or triple bronze (40%; it also includes some other types of alloys based on copper or silver (5%. As the analysis has shown, complex ores seem to be the most probable source of copper. Traditionally, the Urals, the Sayan and the Altay Mountains, Kazakhstan and the Northern Caucasus were regarded as the most probable minefi elds to supply ores to the barren regions of Eastern Europe. While ore sources for products made of metallurgical “pure” copper are localized within the Ural mining and metallurgical region, metal sources for items cast from different groups of alloys (rather than imports of ready-made products require further research.

  11. Indoor atmospheric corrosion of historical ferrous alloys. System characterisation, mechanisms and modelling discussion

    International Nuclear Information System (INIS)

    Monnier, J.

    2008-12-01

    Understanding the mechanisms of indoor atmospheric corrosion in iron alloys is of primary importance in several fields, including for the conservation of Middle Ages monuments or the long term storage of nuclear waste. In this research, a double approach was developed, combining fine characterisation of corrosion systems and design of experiments to answers specific questions related to mechanisms understanding. Iron indoor atmospheric corrosion was investigated on samples coming from the reinforcing chain of the Amiens cathedral (15. century). In the first stage, the corrosion system has been extensively characterised from the macroscopic to the nano-metric scale. In particular, structural micro-analysis (μ-Raman, μ-XRD, μ-XAS) has been used to locate, identify and quantify the oxidised phases. Rust layers are composed of a matrix of nano-metric goethite, with low quantities of lepidocrocite and akaganeite mostly located in the extern part of the corrosion system. In addition, clear marblings are dispersed in the matrix, which are sometimes connected with the metal core. Although these may contain maghemite, these marblings are generally made of ferri-hydrite/feroxyhite phases. In the second stage, specific experiments have been carried out in an unsaturated marked medium to locate oxygen reduction sites in the rust layers. Several cases were evidenced, depending on the rust layer morphology. In addition, reduction processes of model phases have been studied in situ, using an electrochemical cell coupled with structural characterisation techniques. This combination highlighted the influence of reduction mode and pH on the type of reduced phase formed. From the obtained results, several mechanisms are proposed to explain the long term indoor atmospheric corrosion of iron, including rust layers morphology and phases properties. The different hypotheses have been integrated in a proposed method to diagnosis ancient ferrous systems stability. These hypotheses also

  12. Degradation of bisphenol A in aqueous solution by persulfate activated with ferrous ion.

    Science.gov (United States)

    Jiang, Xiaoxuan; Wu, Yanlin; Wang, Peng; Li, Hongjing; Dong, Wenbo

    2013-07-01

    Degradation of bisphenol A (BPA) in aqueous solution was studied with high-efficiency sulfate radical (SO4(-·)), which was generated by the activation of persulfate (S2O8(2-)) with ferrous ion (Fe(2+)). S2O8(2-) was activated by Fe(2+) to produce SO4(-·), and iron powder (Fe(0)) was used as a slow-releasing source of dissolved Fe(2+). The major oxidation products of BPA were determined by liquid chromatography-mass spectrometer. The mineralization efficiency of BPA was monitored by total organic carbon (TOC) analyzer. BPA removal efficiency was improved by the increase of initial S2O8(2-) or Fe(2+) concentrations and then decreased with excess Fe(2+) concentration. The adding mode of Fe(2+) had significant impact on BPA degradation and mineralization. BPA removal rates increased from 49 to 97% with sequential addition of Fe(2+), while complete degradation was observed with continuous diffusion of Fe(2+), and the latter achieved higher TOC removal rate. When Fe(0) was employed as a slow-releasing source of dissolved Fe(2+), 100% of BPA degradation efficiency was achieved, and the highest removal rate of TOC (85%) was obtained within 2 h. In the Fe(0)-S2O8(2-) system, Fe(0) as the activator of S2O8(2-) could offer sustainable oxidation for BPA, and higher TOC removal rate was achieved. It was proved that Fe(0)-S2O8(2-) system has perspective for future works.

  13. Standing Concertation Committee

    CERN Multimedia

    2007-01-01

    ORDINARY MEETING ON 30 JANUARY 2007 The main items discussed at the meeting of the Standing Concertation Committee on 30 January 2007 included: Administrative Circular No. 26: with the introduction of the merit recognition system in the framework of the 5-yearly review of CERN employment conditions, Administrative Circular No. 26 has been revised. The Committee took note of the revised document which is being finalized for submission to the Director-General for approval in the near future. Technical analysis of CERN Health Insurance Scheme: the Committee was informed that a group has been set up by the Director-General to analyse the financial situation of the CERN Health Insurance Scheme in the short and long term, and to propose measures to ensure that the Scheme remains in financial balance, with adequate cover, over the medium term. The group's terms of reference and membership were communicated. Voluntary programmes It was announced that the programmes: 'part-time work as a pre-retirement mea...

  14. Standing Concertation Committee

    CERN Multimedia

    2007-01-01

    Ordinary meeting on 30 January 2007 The main items discussed at the meeting of the Standing Concertation Committee on 30 January 2007 included: Administrative Circular No. 26: with the introduction of the merit recognition system in the framework of the 5-yearly review of CERN employment conditions, Administrative Circular No. 26 has been revised. The committee took note of the revised document which is being finalized for submission to the Director-General for approval in the near future. Technical analysis of CERN Health Insurance Scheme: the Committee was informed that a group has been set up by the Director-General to analyse the financial situation of the CERN Health Insurance Scheme in the short and long term, and to propose measures to ensure that the Scheme remains in financial balance, with adequate cover, over the medium term. The group's terms of reference and membership were communicated. Voluntary programmes It was announced that the programmes: 'part-time work as a pre-retirement measure...

  15. Standing Concertation Committee

    CERN Multimedia

    HR Department

    2007-01-01

    ORDINARY MEETING ON 27 FEBRUARY 2007 The main items discussed at the meeting of the Standing Concertation Committee on 27 February 2007 included: Saved Leave Scheme (SLS): It was announced that a Management/Staff Association working group had been set up to discuss the Saved Leave Scheme (SLS): Members : M. Büttner, E. Chiaveri (chair), Ph. Defert, D. Klem, M. Vitasse, J.-M. Saint-Viteux. It was noted that the Staff Association was launching a questionnaire on SLS and distributed to all members of the personnel. Merit Recognition Guidelines: In the context of the new Merit Appraisal and Recognition Scheme (MARS), the committee took note of the CERN-wide 2007 Merit Recognition Guidelines, including the Frequently Asked Questions on HR Department's dedicated website. Information on CERN's medium and long-term plans (MTP-LTP)/Contract renewals/ External mobility The Committee took note of the information provided on CERN's MTP-LTP and of documentation distributed at the meeting by the Staff ...

  16. Wavelength resolved neutron transmission analysis to identify single crystal particles in historical metallurgy

    Science.gov (United States)

    Barzagli, E.; Grazzi, F.; Salvemini, F.; Scherillo, A.; Sato, H.; Shinohara, T.; Kamiyama, T.; Kiyanagi, Y.; Tremsin, A.; Zoppi, Marco

    2014-07-01

    The phase composition and the microstructure of four ferrous Japanese arrows of the Edo period (17th-19th century) has been determined through two complementary neutron techniques: Position-sensitive wavelength-resolved neutron transmission analysis (PS-WRNTA) and time-of-flight neutron diffraction (ToF-ND). Standard ToF-ND technique has been applied by using the INES diffractometer at the ISIS pulsed neutron source in the UK, while the innovative PS-WRNTA one has been performed at the J-PARC neutron source on the BL-10 NOBORU beam line using the high spatial high time resolution neutron imaging detector. With ToF-ND we were able to reach information about the quantitative distribution of the metal and non-metal phases, the texture level, the strain level and the domain size of each of the samples, which are important parameters to gain knowledge about the technological level of the Japanese weapon. Starting from this base of data, the more complex PS-WRNTA has been applied to the same samples. This experimental technique exploits the presence of the so-called Bragg edges, in the time-of-flight spectrum of neutrons transmitted through crystalline materials, to map the microstructural properties of samples. The two techniques are non-invasive and can be easily applied to archaeometry for an accurate microstructure mapping of metal and ceramic artifacts.

  17. 77 FR 12353 - Shipping Coordinating Committee; Notice of Committee Meeting

    Science.gov (United States)

    2012-02-29

    ... to entry into force of the International Labour Organization Maritime Labour Convention, 2006; Fair... offshore exploration and exploitation activities; Consideration of the report of the Committee on its...

  18. Obtainment, machining and wear of metal matrix composites processed by powder metallurgy

    International Nuclear Information System (INIS)

    Jesus, Edilson Rosa Barbosa de.

    1998-01-01

    The aim of this investigation was the obtainment of metal matrix composites (MMC) by the route of powder metallurgy, and the valuation of these materials with relation to their machining and wear characteristics. Firstly, were obtained pure commercial aluminium matrix composites materials, with 5, 10 and 15% volumetric fraction of silicon carbide particles. Was also obtained a material without reinforcement particles in order to verify by comparison, the influence of addition of reinforcement particles. The obtained materials were characterized physics (hydrostatic density), mechanics (hardness and tensile tests) and microstructurally (optical microscopy and scanning electron microscopy). The results showed a homogeneous distribution of reinforcement particles in the composite, and improvement in the mechanical properties, mainly tensile strength (UTS) in comparison to the unreinforced material. After, tests were made to verify the materials behavior during machining and to check the performance of several tool materials (cemented carbide, ceramics and polycrystalline diamond). In these tests, values of the cutting force were measured by instrumented tool-holders. Phenomena such as tool wear, built-up edge formation and mechanism of chip formation were also observed and evaluated. The results from the cemented carbide tool tests, were utilised for the machinability index determination of each material. These results were applied to the Taylor equation and the equation constants for each material and test conditions were determined. The results showed that the inclusion of silicon carbide particles made extremely difficult the machining of the composites, and only with diamond tool, satisfactory results were obtained. At last, wear tests were performed to verify the influence of the reinforcement particles in the characteristics of wear resistance of the materials. The results obtained were utilized in the wear coefficient determination for each material. The

  19. Filamentary niobium--tin superconductors fabricated by a powder metallurgy approach

    International Nuclear Information System (INIS)

    Hemachalam, K.

    1976-02-01

    Procedures are described for making superconducting tapes and wires containing filments of the A-15 compound, Nb 3 Sn, by powder metallurgy techniques. The Nb 3 Sn filaments, typically 1-5 m thick, are formed by a short heat treatment. The effects of process variables on the microstructure of the tapes and wires were investigated. Microstructural aspects were examined by optical metallography and transmission electron microscopy. A pulsed field technique was used to determine the critical current density, J/sub c/, at 4.2 0 K as a function of transverse magnetic field up to 170 kG. Satisfactory agreement was oserved between these results and data obtained under steady fields of up to 100 kG. The J/sub c/ of the conductors are related to their individual filament morphologies resulting from the different thermo-mechanical histories. The effect of heat treatment conditions on critical current and transition temperature, T/sub c/, is presented. Through process modifications, optimal values or ranges are developed for the metallugical variables in order to maximize the superconducting properties. The inductively measured T/sub c/ of the conductors is about 17.9 +- 0.1 0 . The values of J/sub c/ for the wires computed on the basis of Nb 3 Sn and niobium matrix are 2.3 x 10 5 A/cm 2 at a transverse pulse field of 50 kG, 1.1 x 10 5 A/cm 2 at 100 kG and 7.5 x 10 4 A/cm 2 at 150 kG

  20. The metallurgy, mechanics, modelling and assessment of dissimilar material brazed joints

    International Nuclear Information System (INIS)

    Hamilton, Niall Robert; Wood, James; Galloway, Alexander; Olsson Robbie, Mikael Brian; Zhang Yuxuan

    2013-01-01

    At the heart of any procedure for modelling and assessing the design or failure of dissimilar material brazed joints there must be a basic understanding of the metallurgy and mechanics of the joint. This paper is about developing this understanding and addressing the issues faced with modelling and predicting failure in real dissimilar material brazed joints and the challenges still to be overcome in many cases. An understanding of the key metallurgical features of such joints in relation to finite element modelling is presented in addition to a study of the mechanics and stress state at an abrupt interface between two materials. A discussion is also presented on why elastic singularities do not exist based on a consideration of the assumption of an abrupt change in material properties and plasticity in the vicinity of the joint. In terms of modelling real dissimilar material brazed joints; there are several barriers to accurately capturing the stress state in the region of the joint and across the brazed layer and these are discussed in relation to a metallurgical study of a real dissimilar material brazed joint. However, this does not preclude using a simplified modelling approach with a representative braze layer in design and failure assessment away from the interface. In addition modelling strategies and techniques for assessing the various failure mechanisms of dissimilar material brazed joints are discussed. The findings from this paper are applicable to dissimilar material brazed joints found in a range of applications; however the references listed are primarily focussed on work in fusion research and development.

  1. In vitro degradation and cytotoxicity of Mg/Ca composites produced by powder metallurgy.

    Science.gov (United States)

    Zheng, Y F; Gu, X N; Xi, Y L; Chai, D L

    2010-05-01

    Mg/Ca (1 wt.%, 5 wt.%, 10 wt.% Ca) composites were prepared from pure magnesium and calcium powders using the powder metallurgy method, aiming to enlarge the addition of Ca content without the formation of Mg(2)Ca. The microstructures, mechanical properties and cytotoxicities of Mg/Ca composite samples were investigated. The corrosion of Mg/Ca composites in Dulbecco's modified Eagle's medium (DMEM) for various immersion intervals was studied by electrochemical impedance spectroscopy measurements and environmental scanning electron microscope, with the concentrations of released Mg and Ca ions in DMEM for various immersion time intervals being measured. It was shown that the main constitutional phases were Mg and Ca, which were uniformly distributed in the Mg matrix. The ultimate tensile strength (UTS) and elongation of experimental composites decreased with increasing Ca content, and the UTS of Mg/1Ca composite was comparable with that of as-extruded Mg-1Ca alloy. The corrosion potential increased with increasing Ca content, whereas the current density and the impedance decreased. It was found that the protective surface film formed quickly at the initial immersion stage. With increasing immersion time, the surface film became compact, and the corrosion rate of Mg/Ca composites slowed down. The surface film consisted mainly of CaCO(3), MgCO(3)x3H(2)O, HA and Mg(OH)(2) after 72 h immersion in DMEM. Mg/1Ca and Mg/5Ca composite extracts had no significant toxicity (p>0.05) to L-929 cells, whereas Mg/10Ca composite extract induced approximately 40% reduced cell viability. Copyright (c) 2009 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

  2. Regional Logistics of Procurement of the Ferrous Scrap by the Iron-and-Steel Companies of the Russian Federation

    Directory of Open Access Journals (Sweden)

    Tatiana Aleksandrovna Ivanova

    2017-03-01

    Full Text Available The article discusses the relevant problem of iron-and-steel companies saving on purchasing the scrap metal. The analysis of the current state of the ferrous scrap market in the Russian Federation, trends of its development, led the authors to an opportunity to reduce the cost for purchasing scrap trough the optimal distribution of the regions between Russian iron-and-steel companies where they purchase ferrous scrap. The optimization of the regional structure of the scrap procurement taking into account the regional volumes of its generation and consumption results from using the linear programming methods applying three variants of the problem statement: minimizing the total cost of the scrap delivery to the factory, minimizing the total cost of the scrap at the “export parity” price with delivery, minimizing the total cost of the scrap at the actual prices with delivery. The authors have developed software for performing the calculations. The source are the database of the JSC Russian Railways, which provides information about the transportation of the ferrous scrap between stations of the Russian Federation by railroad; railway rates guide between railway stations of the Russian Federation; statistical data on the prices for scrap metal of the type 3A in “export windows”; actual purchasing prices for the scrap of the 3A type for the range of separate companies of the Russian Federation for several years. As a result, the authors have obtained the optimal regional structure of scrap purchasing for customers in the Russian Federation. We have formulated the recommendations for individual companies regarding the optimal routes of the procurement with scrap. The study has confirmed the possibility to decrease expanses for purchasing the scrap metal for all iron-and-steel factories of the Russian Federation through the optimization of the regional structure of procurement. It is also has allowed to estimate the possibility to cut expenses

  3. Alginate inhibits iron absorption from ferrous gluconate in a randomized controlled trial and reduces iron uptake into Caco-2 cells.

    Science.gov (United States)

    Wawer, Anna A; Harvey, Linda J; Dainty, Jack R; Perez-Moral, Natalia; Sharp, Paul; Fairweather-Tait, Susan J

    2014-01-01

    Previous in vitro results indicated that alginate beads might be a useful vehicle for food iron fortification. A human study was undertaken to test the hypothesis that alginate enhances iron absorption. A randomised, single blinded, cross-over trial was carried out in which iron absorption was measured from serum iron appearance after a test meal. Overnight-fasted volunteers (n = 15) were given a test meal of 200 g cola-flavoured jelly plus 21 mg iron as ferrous gluconate, either in alginate beads mixed into the jelly or in a capsule. Iron absorption was lower from the alginate beads than from ferrous gluconate (8.5% and 12.6% respectively, p = 0.003). Sub-group B (n = 9) consumed the test meals together with 600 mg calcium to determine whether alginate modified the inhibitory effect of calcium. Calcium reduced iron absorption from ferrous gluconate by 51%, from 11.5% to 5.6% (p = 0.014), and from alginate beads by 37%, from 8.3% to 5.2% (p = 0.009). In vitro studies using Caco-2 cells were designed to explore the reasons for the difference between the previous in vitro findings and the human study; confirmed the inhibitory effect of alginate. Beads similar to those used in the human study were subjected to simulated gastrointestinal digestion, with and without cola jelly, and the digestate applied to Caco-2 cells. Both alginate and cola jelly significantly reduced iron uptake into the cells, by 34% (p = 0.009) and 35% (p = 0.003) respectively. The combination of cola jelly and calcium produced a very low ferritin response, 16.5% (p iron for the purpose of food fortification. ClinicalTrials.gov NCT01528644.

  4. Quillaja saponaria bark saponin protects Wistar rats against ferrous sulphate-induced oxidative and inflammatory liver damage.

    Science.gov (United States)

    Ahmed Abdel-Reheim, Mustafa; Messiha, Basim Anwar Shehata; Abo-Saif, Ali Ahmed

    2017-12-01

    Saponins from different sources are historically reported in Chinese medicine to possess many beneficial effects. However, insufficient experimental data are available regarding the hepatoprotective potential of Quillaja bark saponin. The protective effect of Quillaja saponaria Molina (Quillajaceae) bark triterpenoid saponin against iron-induced hepatotoxicity is compared to the standard N-acetylcysteine in adult male Wistar rats. Animals were divided into (six) groups, namely a normal control, an N-acetylcysteine control (300 mg/kg/day, p.o., 10 days), a saponin control (100 mg/kg/day, p.o., for 10 days), a hepatotoxicity control (two doses of ferrous sulphate, 30 mg/kg/day each, i.p., on 9th and 10th day), an N-acetylcysteine plus ferrous sulphate (standard treatment) and a saponin plus ferrous sulphate (test treatment) group. Hepatocyte integrity loss markers (serum ALT, AST, ALP, GGT and LDH), oxidative stress markers (hepatic MDA, GSH and NO x ), dyslipidaemic markers (serum TC and TG) and hepatocyte functioning markers (serum bilirubin and albumin) were assessed. Quillaja bark saponin decreased iron-induced elevation of ALT (reaching 57% of hepatotoxicity control), AST (66%), ALP (76%), GGT (60%), LDH (54%), MDA (65%), NO x (77%), TC (70%), TG (54%), and total (54%), direct (54%) and indirect (54%) bilirubin, coupled with increased GSH (219%) and albumin (159%) levels. Histopathological study strongly supported biochemical estimations, while immunohistochemical study showed marked effect on eNOS and iNOS expression. Quillaja bark saponin has a good hepatoprotective effect. Amelioration of oxidative stress and suppression of NOS expression, with resultant maintenance of hepatocyte integrity and functioning, may explain this beneficial effect.

  5. O2-mediated oxidation of ferrous nitrosylated human serum heme-albumin is limited by nitrogen monoxide dissociation

    International Nuclear Information System (INIS)

    Ascenzi, Paolo; Gullotta, Francesca; Gioia, Magda; Coletta, Massimo; Fasano, Mauro

    2011-01-01

    Research highlights: → Human serum heme-albumin displays globin-like properties. → O 2 -mediated oxidation of ferrous nitrosylated human serum heme-albumin. → Allosteric modulation of human serum heme-albumin reactivity. → Rifampicin is an allosteric effector of human serum heme-albumin. → Human serum heme-albumin is a ROS and NOS scavenger. -- Abstract: Human serum heme-albumin (HSA-heme-Fe) displays globin-like properties. Here, kinetics of O 2 -mediated oxidation of ferrous nitrosylated HSA-heme-Fe (HSA-heme-Fe(II)-NO) is reported. Values of the first-order rate constants for O 2 -mediated oxidation of HSA-heme-Fe(II)-NO (i.e., for ferric HSA-heme-Fe formation) and for NO dissociation from HSA-heme-Fe(II)-NO (i.e., for NO replacement by CO) are k = 9.8 x 10 -5 and 8.3 x 10 -4 s -1 , and h = 1.3 x 10 -4 and 8.5 x 10 -4 s -1 , in the absence and presence of rifampicin, respectively, at pH = 7.0 and T = 20.0 o C. The coincidence of values of k and h indicates that NO dissociation represents the rate limiting step of O 2 -mediated oxidation of HSA-heme-Fe(II)-NO. Mixing HSA-heme-Fe(II)-NO with O 2 does not lead to the formation of the transient adduct(s), but leads to the final ferric HSA-heme-Fe derivative. These results reflect the fast O 2 -mediated oxidation of ferrous HSA-heme-Fe and highlight the role of drugs in modulating allosterically the heme-Fe-atom reactivity.

  6. Lactoferrin or ferrous salts for iron deficiency anemia in pregnancy: A meta-analysis of randomized trials.

    Science.gov (United States)

    Abu Hashim, Hatem; Foda, Osama; Ghayaty, Essam

    2017-12-01

    This systematic review and meta-analysis aimed to evaluate the efficacy of daily oral bovine lactoferrin versus daily oral ferrous iron preparations for treatment of iron deficiency anemia (IDA) during pregnancy. Searches were conducted on PubMed, ScienceDirect, ClinicalTrials.gov and CENTRAL databases from inception to February 2017 and the bibliographies of retrieved articles were screened. The PRISMA Statement was followed. Published English language randomized trials comparing lactoferrin with oral ferrous iron preparations in pregnant women with iron deficiency anemia were included. Quasi-randomized, non- randomized or studies including other known cause of anemia, gestational or pre-existent maternal diseases were excluded. Accordingly, 4 eligible trials (600 women) were analyzed. Primary outcome was change in hemoglobin level at 4 weeks of treatment. Secondary outcomes were; change in serum ferritin and iron, rates of gastrointestinal side effects, preterm birth, low birthweight, neonatal death and mean birthweight. Quality assessment was performed by the Cochrane risk of bias tool. Odds ratio and mean difference were used to integrate dichotomous and continuous outcomes respectively. Pooled estimates for change in hemoglobin levels at four weeks favored daily oral lactoferrin over daily oral ferrous sulphate (mean difference 0.77; 95% confidence interval [CI] 0.04-1.55; P=0.04, 4 trials, 600 women). However, after subgroup analysis (degree of anemia), no significant difference in hemoglobin levels were found between both groups in mild anemia (mean difference 0.80; 95% CI -0.21 to 1.82, 3 trials, 372 women), but a significant increase favoring lactoferrin was reported in moderate anemia (mean difference 0.68; 95% CI 0.53-0.83; P<0.00001, one trial, 228 women). Significantly less gastrointestinal side effects were reported with lactoferrin treatment. No significant differences existed with regard to other outcomes. In conclusion, for pregnant women with IDA

  7. Irradiation of ferrous ammonium sulfate for its use as high absorbed dose and low-temperature dosimeter

    International Nuclear Information System (INIS)

    Juarez-Calderon, J.M.; Negron-Mendoza, A.; Ramos-Bernal, S.

    2007-01-01

    In the present paper, we study the response of crystalline ammonium ferrous sulfate as a function of the irradiation dose and temperature. The dose studied ranged from 33.5 to 546 kGy. The temperature regimen varied from 77 K (liquid nitrogen) to 311 K. The analysis of the samples was made by UV spectroscopy and EPR. The results show that the change in absorbance of the dosimeter was linear with respect to the absorbed dose in the range studied. There is a small influence of the irradiation temperature in the response of the iron salt. The dose rate and storage time after irradiation was of no importance in this application

  8. Fine and ultrafine emission dynamics from a ferrous foundry cupola furnace.

    Science.gov (United States)

    Meléndez, Antton; García, Estibaliz; Carnicer, Pedro; Pena, Egoitz; Larrión, Miren; Legarreta, Juan Andres; Gutiérrez-Cañas, Cristina

    2010-05-01

    Aerosol size distributions from ferrous foundry cupola furnaces vary depending on semicontinuous process dynamics, time along the tap-to-tap cycle, dilution ratio, and the physical and chemical nature of the charge and fuel. All of these factors result in a highly time-dependent emission of particulate matter (PM) 2.5 pm or less in aerodynamic diameter (PM2.5)--even on a mass concentration basis. Control measures are frequently taken on the basis of low-reliability parameters such as emission factors and loosely established mass ratios of PM2.5 to PM 10 microm or less in aerodynamic diameter (PM1.0). The new environmental requirements could entail unexpected and undesired drawbacks and uncertainties in the meaning and effectiveness of process improvement measures. The development of process-integrated and flue-gas cleaning measures for reduction of particle emissions requires a better knowledge of generation mechanisms during melting. Available aerosol analyzers expand the range of control issues to be tackled and contribute to greatly reduce the uncertainty of engineering decisions on trace pollutant control. This approach combines real-time size distribution monitoring and cascade impactors as preseparators for chemical or morphological analysis. The results allow for establishing a design rationale and performance requirement for control devices. A number size distribution below 10 microm in aerodynamic equivalent diameter was chosen as the main indicator of charge influence and filter performance. Size distribution is trimodal, with a coarse mode more than 12 microm that contributes up to 30% of the total mass. A temporal series for these data leads to identification of the most relevant size ranges for a specific furnace (e.g., the most penetrating size range). In this cupola, this size range is between 0.32 and 0.77 microm of aerodynamic equivalent diameter and defines the pollution control strategy for metals concentrating within this size range. Scrap

  9. Business ethics in ethics committees?

    Science.gov (United States)

    Boyle, P

    1990-01-01

    The "Ethics committees" column in this issue of the Hastings Center Report features an introduction by Cynthia B. Cohen and four brief commentaries on the roles hospital ethics committees may play in the making of institutional and public health care policy in the 1990s. The pros and cons of a broader, more public role for ethics committees in reconciling the business and patient care aspects of health care delivery are debated by Cohen in "Ethics committees as corporate and public policy advocates," and by Philip Boyle in this article. Boyle is an associate for ethical studies at The Hastings Center.

  10. [Ethics in committees].

    Science.gov (United States)

    Hottois, Gilbert

    2007-01-01

    The management of techno-scientific and multicultural societies, open and evolving, can neither be conceived nor carried out on the basis of fundamentalist, essentialist rules that are characteristic of closed, immobile societies. Within a global civilisation, fundamentalisms are only acceptable as individual or community beliefs. Against the background of our civilisation on the chaotic road to globalisation described here, what are the methodological rules for bioethics committees? A first rule concerns the composition of the committees: it must be multidisciplinary and pluralist. The second rule concerns the distinction of types, which is less evident at a time which cultivates postmodernism. The "types" which absolutely must be distinguished are: science, ethics, morals, law, politics. The third rule concerns the concluding procedures. A majority vote procedure after information and limited discussion makes it possible to conclude easily and rapidly. But it generally seems not to be very ethical, especially if it does not allow minorities to have their divergent opinions appear among the conclusions in an explicit argued manner. The "lazy dissensus" must, however also be avoided: it consists in not really engaging the interdisciplinary, pluralist discussion, simply exposing and explaining each position, on the pretext that pluralism is respecting diversity, the freedom to believe, to think and to express oneself either each for himself or in the name of one's community or tradition. This sort of "postmodern" methodology, individualistic and communitarian to an extreme, is precariously balanced in relation to the committee's ethical vocation. It is therefore very important that an ethics committee really engages in discussion and expresses, let's say, a preference for consensus. This preference is the expression of its "ethical" nature: in this word (as in the word "moral", in fact), there is a reference to what is common, to what unites and makes social life

  11. Study of alumina-trichite reinforcement of a nickel-based matric by means of powder metallurgy

    Science.gov (United States)

    Walder, A.; Hivert, A.

    1982-01-01

    Research was conducted on reinforcing nickel based matrices with alumina trichites by using powder metallurgy. Alumina trichites previously coated with nickel are magnetically aligned. The felt obtained is then sintered under a light pressure at a temperature just below the melting point of nickel. The halogenated atmosphere technique makes it possible to incorporate a large number of additive elements such as chromium, titanium, zirconium, tantalum, niobium, aluminum, etc. It does not appear that going from laboratory scale to a semi-industrial scale in production would create any major problems.

  12. Effects of carbon and hafnium concentrations in wrought powder-metallurgy superalloys based on NASA 2B-11 alloy

    Science.gov (United States)

    Miner, R. V., Jr.

    1976-01-01

    A candidate alloy for advanced-temperature turbine engine disks, and four modifications of that alloy with various C and Hf concentrations were produced as cross-rolled disks from prealloyed powder that was hot isostatically compacted. The mechanical properties, microstructures, and phase relations of the alloys are discussed in terms of their C and Hf concentrations. A low-C and high-Hf modification of IIB-11 had the best balance of mechanical properties for service below about 750 C. Because of their finer grain sizes, none of the powder-metallurgy alloys produced had the high-temperature rupture strength of conventionally cast and wrought IIB-11.

  13. Early atmospheric metal pollution provides evidence for Chalcolithic/Bronze Age mining and metallurgy in Southwestern Europe

    Energy Technology Data Exchange (ETDEWEB)

    Martínez Cortizas, Antonio, E-mail: antonio.martinez.cortizas@usc.es [Departamento de Edafoloxía e Química Agrícola, Facultade de Bioloxía, Universidade de Santiago de Compostela, Campus Sur s/n, Santiago de Compostela (Spain); López-Merino, Lourdes, E-mail: lourdes.lopez-merino@brunel.ac.uk [Institute of Environment, Health and Societies, Brunel University London, UB8 3PH Uxbridge (United Kingdom); Bindler, Richard, E-mail: richard.bindler@umu.se [Department of Ecology and Environmental Science, Umeå University, Umeå (Sweden); Mighall, Tim, E-mail: t.mighall@abdn.ac.uk [Department of Geography & Environment, School of Geosciences, University of Aberdeen, Elphinstone Road, Aberdeen AB24 3UF (United Kingdom); Kylander, Malin E., E-mail: malin.kylander@geo.su.se [Department of Geological Sciences and the Bolin Centre for Climate Research, Stockholm University, SE-10691, Stockholm (Sweden)

    2016-03-01

    Although archaeological research suggests that mining/metallurgy already started in the Chalcolithic (3rd millennium BC), the earliest atmospheric metal pollution in SW Europe has thus far been dated to ~ 3500–3200 cal. yr. BP in paleo-environmental archives. A low intensity, non-extensive mining/metallurgy and the lack of appropriately located archives may be responsible for this mismatch. We have analysed the older section (> 2100 cal. yr. BP) of a peat record from La Molina (Asturias, Spain), a mire located in the proximity (35–100 km) of mines which were exploited in the Chalcolithic/Bronze Age, with the aim of assessing evidence of this early mining/metallurgy. Analyses included the determination of C as a proxy for organic matter content, lithogenic elements (Si, Al, Ti) as markers of mineral matter, and trace metals (Cr, Cu, Zn, Pb) and stable Pb isotopes as tracers of atmospheric metal pollution. From ~ 8000 to ~ 4980 cal. yr. BP the Pb composition is similar to that of the underlying sediments (Pb 15 ± 4 μg g{sup −1}; {sup 206}Pb/{sup 207}Pb 1.204 ± 0.002). A sustained period of low {sup 206}Pb/{sup 207}Pb ratios occurred from ~ 4980 to ~ 2470 cal. yr. BP, which can be divided into four phases: Chalcolithic (~ 4980–3700 cal. yr. BP), {sup 206}Pb/{sup 207}Pb ratios decline to 1.175 and Pb/Al ratios increase; Early Bronze Age (~ 3700–3500 cal. yr. BP), {sup 206}Pb/{sup 207}Pb increase to 1.192 and metal/Al ratios remain stable; Late Bronze Age (~ 3500–2800 cal. yr. BP), {sup 206}Pb/{sup 207}Pb decline to their lowest values (1.167) while Pb/Al and Zn/Al increase; and Early Iron Age (~ 2800–2470 cal. yr. BP), {sup 206}Pb/{sup 207}Pb increase to 1.186, most metal/Al ratios decrease but Zn/Al shows a peak. At the beginning of the Late Iron Age, {sup 206}Pb/{sup 207}Pb ratios and metal enrichments show a rapid return to pre-anthropogenic values. These results provide evidence of regional/local atmospheric metal pollution triggered by the

  14. Study of Proper Time Range for Current Flow to Resistance Spot Welding Inspected by Mechanical Property and Metallurgy Testing

    International Nuclear Information System (INIS)

    Pearsura, Prachya

    2007-08-01

    Full text: This research used the mechanical property and metallurgy testing to identify the proper time range for current flow. The specimen tested was 1 mm thick mild steel. The welded specimens were tested by Tensile Shear testing following JIS Z 3136: 1999 and Macro Structure testing follow by JIS Z 3139: 1978. Subsequently, the results from analyzing were compared with standard JIS Z 3140. The results show that the suitable current flow is 8 to 10 cycles. This technique can be applied to monitor the process and the quality of resistance spot welding

  15. Early atmospheric metal pollution provides evidence for Chalcolithic/Bronze Age mining and metallurgy in Southwestern Europe.

    Science.gov (United States)

    Martínez Cortizas, Antonio; López-Merino, Lourdes; Bindler, Richard; Mighall, Tim; Kylander, Malin E

    2016-03-01

    Although archaeological research suggests that mining/metallurgy already started in the Chalcolithic (3rd millennium BC), the earliest atmospheric metal pollution in SW Europe has thus far been dated to ~3500-3200 cal.yr. BP in paleo-environmental archives. A low intensity, non-extensive mining/metallurgy and the lack of appropriately located archives may be responsible for this mismatch. We have analysed the older section (>2100 cal.yr. BP) of a peat record from La Molina (Asturias, Spain), a mire located in the proximity (35-100 km) of mines which were exploited in the Chalcolithic/Bronze Age, with the aim of assessing evidence of this early mining/metallurgy. Analyses included the determination of C as a proxy for organic matter content, lithogenic elements (Si, Al, Ti) as markers of mineral matter, and trace metals (Cr, Cu, Zn, Pb) and stable Pb isotopes as tracers of atmospheric metal pollution. From ~8000 to ~4980 cal.yr. BP the Pb composition is similar to that of the underlying sediments (Pb 15 ± 4 μg g(-1); (206)Pb/(207)Pb 1.204 ± 0.002). A sustained period of low (206)Pb/(207)Pb ratios occurred from ~4980 to ~2470 cal.yr. BP, which can be divided into four phases: Chalcolithic (~4980-3700 cal.yr. BP), (206)Pb/(207)Pb ratios decline to 1.175 and Pb/Al ratios increase; Early Bronze Age (~3700-3500 cal.yr. BP), (206)Pb/(207)Pb increase to 1.192 and metal/Al ratios remain stable; Late Bronze Age (~3500-2800 cal.yr. BP), (206)Pb/(207)Pb decline to their lowest values (1.167) while Pb/Al and Zn/Al increase; and Early Iron Age (~2800-2470 cal.yr. BP), (206)Pb/(207)Pb increase to 1.186, most metal/Al ratios decrease but Zn/Al shows a peak. At the beginning of the Late Iron Age, (206)Pb/(207)Pb ratios and metal enrichments show a rapid return to pre-anthropogenic values. These results provide evidence of regional/local atmospheric metal pollution triggered by the earliest phases of mining/metallurgy in the area, and reconcile paleo-environmental and

  16. Annual Report on Scientific Activities in 1997 of Department of Physics and Nuclear Techniques, Academy of Mining and Metallurgy, Cracow

    International Nuclear Information System (INIS)

    Wolny, J.; Olszynska, E.

    1998-01-01

    The Annual Report 1997 is the review of scientific activities of the Department of Nuclear Physics and Techniques (DNPT) of the Academy of Mining and Metallurgy, Cracow. The studies connected with: radiometric analysis, nuclear electronics, solid state physics, elementary particle and detectors, medical physics, physics of environment, theoretical physics, nuclear geophysics, energetic problems, industrial radiometry and tracer techniques have been broadly presented. The fill list of works being published and presented at scientific conferences in 1997 by the staff of DNPT are also included

  17. 76 FR 19176 - Shipping Coordinating Committee; Notice of Committee Meeting

    Science.gov (United States)

    2011-04-06

    ...) Maritime Safety Committee (MSC 89) to be held May 11-20, 2011. The primary matters to be considered at MSC... --Technical assistance sub-programme in maritime safety and security --Capacity-building for the... business --Report of the Maritime Safety Committee Members of the public may attend these two meetings up...

  18. 78 FR 29201 - Shipping Coordinating Committee; Notice of Committee Meeting

    Science.gov (United States)

    2013-05-17

    ... the International Maritime Organization's (IMO) Marine Safety Committee to be held at the IMO... session of the Sub-Committee) Technical co-operation activities relating to maritime safety and security... amendments to mandatory instruments Measures to enhance maritime security Goal-based new ship construction...

  19. 78 FR 17466 - Shipping Coordinating Committee; Notice of Committee Meeting

    Science.gov (United States)

    2013-03-21

    ... --Review and modernization of the Global Maritime DIstress and Safety System (GMDSS) --Review of general... and provisional agenda for STW 45 --Any other business --Report to the Maritime Safety Committee... forty-fourth Session of the International Maritime Organization's (IMO) Sub-Committee on Standards of...

  20. 78 FR 32699 - Shipping Coordinating Committee; Notice of Committee Meeting

    Science.gov (United States)

    2013-05-31

    ... Session of the International Maritime Organization's (IMO) Sub-Committee on Safety of Navigation to be... --Report to the Maritime Safety Committee Members of the public may attend this meeting up to the seating... system ``BeiDou'' in the maritime field --International Telecommunication Union (ITU) matters, including...

  1. 77 FR 47491 - Shipping Coordinating Committee; Notice of Committee Meeting

    Science.gov (United States)

    2012-08-08

    ... to the Maritime Safety Committee Members of the public may attend this meeting up to the seating... Session of the International Maritime Organization's (IMO) Sub-Committee on Dangerous Goods, Solid Cargoes... --Amendment 37-14 to the International Maritime Dangerous Goods (IMDG) Code and supplements, including...

  2. 77 FR 57638 - Shipping Coordinating Committee; Notice of Committee Meeting

    Science.gov (United States)

    2012-09-18

    ... the International Maritime Organization's (IMO) Marine Safety Committee to be held at the IMO... seventeenth session of the Sub-Committee); Technical co-operation activities relating to maritime safety and... amendments to mandatory instruments; Measures to enhance maritime security; Goal-based new ship construction...

  3. 78 FR 14400 - Shipping Coordinating Committee; Notice of Committee Meeting

    Science.gov (United States)

    2013-03-05

    ... Organization in London, United Kingdom from May 13 to 17, 2013. The primary matters to be considered include... facilities; --Reports of sub-committees; --Work of other bodies; --Harmful anti-fouling systems for ships... bodies; --Application of the Committees' Guidelines; --Election of the Chairman and Vice-Chairman for...

  4. 76 FR 44977 - Shipping Coordinating Committee; Notice of Committee Meeting

    Science.gov (United States)

    2011-07-27

    ... international trade. --Ship/port interface. --Technical co-operation and assistance. --Relations with other... DEPARTMENT OF STATE [Public Notice 6827] Shipping Coordinating Committee; Notice of Committee... upcoming events at the International Maritime Organization (IMO) in London, United Kingdom. The first of...

  5. 77 FR 54648 - Shipping Coordinating Committee; Notice of Committee Meeting

    Science.gov (United States)

    2012-09-05

    ... International Maritime Organization's Marine Environment Protection Committee (MEPC). The meeting will be held... prepare for the sixty-fourth session of the International Maritime Organization's Marine Environment Protection Committee (MEPC 64) to be held at the International Maritime Organization in London, United...

  6. 75 FR 63888 - Shipping Coordinating Committee; Notice of Committee Meeting

    Science.gov (United States)

    2010-10-18

    ... Work Methods and Organization of Work of the Legal Committee --Any other business --Consideration of... for the ninety-seventh Session of the International Maritime Organization's (IMO) Legal Committee to... Pollution Damage, 2001 --Consideration of a proposal to amend the limits of liability of the 1996 Protocol...

  7. 76 FR 12787 - Shipping Coordinating Committee; Notice of Committee Meeting

    Science.gov (United States)

    2011-03-08

    ... --Any other business. --The public should be aware that Legal Committee has received a proposal to... the International Maritime Organization's (IMO) Legal Committee to be held at the IMO headquarters in... treatment of seafarers in the event of a maritime accident; --Consideration of a proposal to amend the...

  8. 78 FR 77772 - Shipping Coordinating Committee; Notice of Committee Meeting

    Science.gov (United States)

    2013-12-24

    ... management systems and reduction of atmospheric pollution --Consideration of the impact on the Arctic of... agenda --Decisions of other IMO bodies --Evaluation of safety and pollution hazards of liquid chemicals... DEPARTMENT OF STATE [Public Notice 8572] Shipping Coordinating Committee; Notice of Committee...

  9. 78 FR 69991 - Advisory Committee; Veterinary Medicine Advisory Committee; Termination

    Science.gov (United States)

    2013-11-22

    ... HUMAN SERVICES Food and Drug Administration 21 CFR Part 14 Advisory Committee; Veterinary Medicine Advisory Committee; Termination AGENCY: Food and Drug Administration, HHS. ACTION: Final rule. SUMMARY: The Food and Drug Administration (FDA) is announcing the termination of the Veterinary Medicine Advisory...

  10. STANDING CONCERTATION COMMITTEE

    CERN Document Server

    2003-01-01

    ORDINARY MEETING ON 29 SEPTEMBER 2003 Original: English This meeting was devoted to the main topics summarised below. 1 Follow-up from the meetings of TREF and the Finance Committee in September 2003 The last meeting of TREF had been devoted to presentations and clarifications on the 5-Yearly Review process. The content and planning of the 2005 Review are matters for the next Management, which will be presented to TREF next year. Underlining that due account has to be taken of the limited resources available to conduct such an exercise, the Staff Association stated that it looks forward to the concertation process at the SCC in preparing the next 5-Yearly Review to define an optimum set of topics in order to ensure that CERN can attract, retain and motivate the personnel that it needs to remain a centre of excellence. The Chairman of the SCC recalled that an information document on the Cost-Variation Index for 2004 had been transmitted to the Finance Committee last September and that complete information o...

  11. 7 CFR 923.8 - Committee.

    Science.gov (United States)

    2010-01-01

    ... of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements and... IN WASHINGTON Order Regulating Handling Definitions § 923.8 Committee. Committee means the Washington Cherry Marketing Committee established pursuant to § 923.20. ...

  12. 7 CFR 922.8 - Committee.

    Science.gov (United States)

    2010-01-01

    ... of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements and... WASHINGTON Order Regulating Handling Definitions § 922.8 Committee. Committee means the Washington Apricot Marketing Committee established pursuant to § 922.20. ...

  13. Unsteady Casson nanofluid flow over a rotating cone in a rotating frame filled with ferrous nanoparticles: A numerical study

    Energy Technology Data Exchange (ETDEWEB)

    Raju, C.S.K., E-mail: sivaphd90@gmail.com; Sandeep, N., E-mail: dr.nsrh@gmail.com

    2017-01-01

    In this study, we investigated the momentum and heat transfer characteristics of Casson nanofluid flow over a rotating cone in a rotating frame filled with water based CoFe{sub 2}O{sub 4} nano particles. Heat flux conditions and wall temperature conditions are very important in controlling of up and down heat transport phenomena's in industrial as well as engineering application. Resulting set of coupled nonlinear governing equations are solved numerically using Runge–Kutta based shooting technique. In graphical results we presented dual solutions for the prescribed wall temperature (PWT) and prescribed heat flux (PHF) cases. The effect of governing parameters on velocity and temperature fields along with the skin friction coefficient and the heat transfer rate are presented with the help of graphs and tables. Results indicate that the rising values of the volume fraction of ferro particles and buoyancy parameter have tendency to improve the skin friction coefficient as well as the heat transfer rate for both the prescribed wall temperature (PWT) and prescribed heat flux (PHF) cases. - Highlights: • Mathematical model for unsteady nanofluid flow over a rotating cone in a rotating frame. • Water based ferrous nanoparticles suspended Casson model is studied. • Non-uniform heat source/sink is incorporated in the model. • Dual nature found for PWT and PHF cases. • Ferrous nanoparticles effectively enhance the heat transfer rate.

  14. Isotopic characterisation of lead in contaminated soils from the vicinity of a non-ferrous metal smelter near Plovdiv, Bulgaria

    Energy Technology Data Exchange (ETDEWEB)

    Bacon, Jeffrey R. [Macaulay Institute, Craigiebuckler, Aberdeen AB15 8QH (United Kingdom)]. E-mail: j.bacon@macaulay.ac.uk; Dinev, Nikolai S. [N Poushkarov Institute of Soil Science and Agroecology, Sofia (Bulgaria)

    2005-03-01

    Soil samples from the vicinity of a non-ferrous metal smelter near Plovdiv, Bulgaria contained very high concentrations of cadmium, lead and zinc (up to 140, 4900 and 5900 mg kg{sup -1}, respectively). A roadside soil in a relatively uncontaminated area also contained high concentrations of the same metals (24, 1550 and 1870 mg kg{sup -1}, respectively) indicating that the transport of ores could be a source of contamination. Even though the lead isotope ratios in all the samples fell within a very narrow range (for example, 1.186-1.195 for {sup 206}Pb/{sup 207}Pb), the samples could be differentiated into three distinct groups: ores ({sup 206}Pb/{sup 207}Pb and {sup 208}Pb/{sup 207}Pb ratios of 1.1874-1.1884 and 2.4755-2.4807, respectively), current deposition (1.1864 and 2.4704-2.4711, respectively) and local background (1.1927-1.1951 and 2.4772-2.4809, respectively). Although most of the current deposition has its origin in the ores used at the smelter, up to 12% could be from other sources such as petrol lead. - Although soils in the vicinity of a non-ferrous metal smelter near Plovdiv, Bulgaria, have become highly contaminated with the ores used, lead isotope analysis has revealed that up to 12% of current deposition could be from other sources such as petrol lead.

  15. Iron corrosion in archaeological context: Structural refinement of the ferrous hydroxychloride β-Fe2(OH)3Cl

    International Nuclear Information System (INIS)

    Réguer, Solenn; Mirambet, Francois; Rémazeilles, Céline; Vantelon, Delphine; Kergourlay, Florian; Neff, Delphine; Dillmann, Philippe

    2015-01-01

    Highlights: • Precise determination of the structure of β-Fe 2 (OH) 3 Cl on archaeological marine artefact. • Novel XAS results, including fitting procedures of natural β-Fe 2 (OH) 3 Cl. • Novel XRD refinement of β-Fe 2 (OH) 3 Cl from archaeological context. • One of the rare demonstration of the DiffAbs beamline efficient original set up. - Abstract: Ferrous hydroxysalts are found in corrosion layers of archaeological ferrous objects extracted from oxygen-poor environments. The structure of synthetic and natural β-Fe 2 (OH) 3 Cl was investigated by X-ray absorption spectroscopy and X-ray diffraction. The local environments of Cl − and Fe 2+ were precisely determined showing the same structure around Cl − and Fe 2+ atoms whatever the natural or synthesized phase. The crystalline structure was refined confirming the rhombohedral unit cell and R-3m space group. However slight differences observed for the structural parameters and on XRD patterns suggested different crystallite size, strain effects and the influence of the crystallization process.

  16. The Hospitality Education Advisory Committee.

    Science.gov (United States)

    Bloom, Thomas A.

    The use of advisory committees for the development, maintenance, and continued exchange of information for hospitality education programs is discussed. Two types of committees are the general advisory type, which can deal with entire programs on institutional and community levels, and the single-field type, which helps develop programs in specific…

  17. Contribution to the study of copper and copper-arsenic archaeo-metallurgy using light element analysis and experimental fusion

    International Nuclear Information System (INIS)

    Papillon, F.

    1997-01-01

    The objective of this study is to try a direct reconstruction from ancient artefacts of the elaboration technology used in the dawning copper metallurgy. This word is based on both the light elements analysis and the carry out of the principles of physical metallurgy. However the study of an archaeological artefact necessitates the use of non destructive methods. A main aspect of this work consists in developing the most adequate metallographic technique and the methods for the determination of oxygen and carbon by ion beam analysis. Additionally experimental melting of copper and copper arsenic alloys were carried out in laboratory, under various temperature and atmosphere conditions, and 'on the field' in Archeodrome de Beaune, in order to reconstruct part of the prehistorical craftsmanship. The results of measurement are consistent with our general knowledge of oxido-reduction phenomena and the behaviour of copper and copper arsenic alloys s in agreement with the prediction of thermodynamics. The nuclear analysis of three ancient artefacts showed that the oxygen and carbon contents were closer to those of the Archeodrome than those of the laboratory. Further studies of the field should consider all parameters controlling the physical-chemistry of charcoal fire. (author)

  18. Effect of sintering conditions on the microstructural and mechanical characteristics of porous magnesium materials prepared by powder metallurgy.

    Science.gov (United States)

    Čapek, Jaroslav; Vojtěch, Dalibor

    2014-02-01

    There has recently been an increased demand for porous magnesium materials in many applications, especially in the medical field. Powder metallurgy appears to be a promising approach for the preparation of such materials. Many works have dealt with the preparation of porous magnesium; however, the effect of sintering conditions on material properties has rarely been investigated. In this work, we investigated porous magnesium samples that were prepared by powder metallurgy using ammonium bicarbonate spacer particles. The effects of the purity of the argon atmosphere and sintering time on the microstructure (SEM, EDX and XRD) and mechanical behaviour (universal loading machine and Vickers hardness tester) of porous magnesium were studied. The porosities of the prepared samples ranged from 24 to 29 vol.% depending on the sintering conditions. The purity of atmosphere played a significant role when the sintering time exceeded 6h. Under a gettered argon atmosphere, a prolonged sintering time enhanced diffusion connections between magnesium particles and improved the mechanical properties of the samples, whereas under a technical argon atmosphere, oxidation at the particle surfaces caused deterioration in the mechanical properties of the samples. These results suggest that a refined atmosphere is required to improve the mechanical properties of porous magnesium. © 2013.

  19. Comprehensive waste characterization and organic pollution co-occurrence in a Hg and As mining and metallurgy brownfield.

    Science.gov (United States)

    Gallego, J R; Esquinas, N; Rodríguez-Valdés, E; Menéndez-Aguado, J M; Sierra, C

    2015-12-30

    The abandonment of Hg-As mining and metallurgy sites, together with long-term weathering, can dramatically degrade the environment. In this work it is exemplified the complex legacy of contamination that afflicts Hg-As brownfields through the detailed study of a paradigmatic site. Firstly, an in-depth study of the former industrial process was performed to identify sources of different types of waste. Subsequently, the composition and reactivity of As- and Hg-rich wastes (calcines, As-rich soot, stupp, and flue dust) was analyzed by means of multielemental analysis, mineralogical characterization (X-ray diffraction, electronic, and optical microscopy, microbrobe), chemical speciation, and sequential extractions. As-rich soot in the form of arsenolite, a relatively mobile by-product of the pyrometallurgical process, and stupp, a residue originated in the former condensing system, were determined to be the main risk at the site. In addition, the screening of organic pollution was also aimed, as shown by the outcome of benzo(a) pyrene and other PAHs, and by the identification of unexpected Hg organo-compounds (phenylmercury propionate). The approach followed unravels evidence from waste from the mining and metallurgy industry that may be present in other similar sites, and identifies unexpected contaminants overlooked by conventional analyses. Copyright © 2015 Elsevier B.V. All rights reserved.

  20. A quantitative description of the action of high-dose pulses of radiation on aerated acid solutions containing ferrous and chloride ions

    International Nuclear Information System (INIS)

    Bjergbakke, E.; Navaratnam, S.; Parsons, B.J.; Swallow, A.J.

    1987-01-01

    Kinetic measurements of the production of ferric complexes have been made for up to 100 s following a 1 μs pulse of 10 MeV electrons (165 kGy) given to aerated, acid solutions containing ferrous and chloride ions. The yields of ferric ions have been quantitatively accounted for by computations involving a scheme with 34 reactions. The rate constants necessary for a good fit are consistent with published values except for the oxidation of ferrous ions by chlorine atoms for which we now propose a value of 1.3 x 10 10 dm 3 mol -1 s -1 . (author)

  1. Ulceration of the oral mucosa following direct contact with ferrous sulfate in elderly patients: a case report and a review of the French National Pharmacovigilance Database

    Directory of Open Access Journals (Sweden)

    Liabeuf S

    2014-04-01

    Full Text Available Sophie Liabeuf,1–3 Valérie Gras,1 Julien Moragny,1 Marie-Laure Laroche,4 Michel Andrejak1,3On behalf of the French National Network of Pharmacovigilance Centers1Regional Pharmacovigilance Center, Division of Clinical Pharmacology, Amiens University Medical Center and Jules Verne University of Picardy, Amiens, France; 2Clinical Research Centre, Clinical Pharmacology Division, Amiens University Medical Center and the Jules Verne University of Picardy, Amiens, France; 3INSERM U1088, Amiens, France; 4Regional Pharmacovigilance Center, Department of Pharmacology, Toxicology and Pharmacovigilance, Limoges University Medical Center, Limoges, FranceObjective: To report a series of cases of ulceration of the oral mucosa linked to direct contact with ferrous sulfate in elderly patients.Case summary: The first case report concerns the occurrence of widespread oral ulceration in an 87-year-old woman with Alzheimer’s disease. The ulceration extended from the side of the tongue to the floor of the mouth. No clear explanation was found and various local treatments were ineffective. Once it was realized that the ferrous sulfate tablets (given as an iron supplement were crushed prior to administration (due to the patient’s deglutition disorder, withdrawal of this treatment led to rapid resolution of the ulceration. Nine other cases of oral ulcerations associated with ferrous sulfate were identified in the French National Pharmacovigilance Database. All but one of the patients were over 80 years of age and the youngest patient (a 54-year-old had dysphagia associated with facial paralysis.Discussion: Only two other reports of oral ulceration due to ferrous sulfate have been published to date. Mucosal toxicity of ferrous sulfate (which is probably related to oxidative stress has previously been reported for the hypopharynx, the esophageal lumen, and (after inhalation of a tablet the tracheobronchial tree.Conclusion: The mucosal toxicity of ferrous

  2. Committees and organizers

    Science.gov (United States)

    2011-07-01

    Chairman:Jozef Spałek (Kraków) Program Committee:Stephen Blundell (Oxford), J Michael D Coey (Dublin), Dominique Givord (Grenoble), Dariusz Kaczorowski (Wrocław), Roman Micnas (Poznań), Marek Przybylski (Halle), Ludiwig Schultz (Dresden), Vladimir Sechovsky (Prague), Jozef Spałek (Kraków), Henryk Szymczak (Warszawa), Manuel Vázquez (Madrid) Publication Committee:Dariusz Kaczorowski, Robert Podsiadły, Jozef Spałek, Henryk Szymczak, Andrzej Szytuła Local committee:Maria Bałanda, Anna Majcher, Robert Podsiadły, Michał Rams, Andrzej Ślebarski, Krzysztof Tomala Editors of the Proceedings:Jozef Spałek, Krzysztof Tomala, Danuta Goc-Jagło, Robert Podsiadły, Michał Rams, Anna Majcher Plenary, semi-plenary and tutorial speakers:Ernst Bauer (Wien)Stephen Blundell (Oxford)J Michael D Coey (Dublin)Russell P Cowburn (London)Burkard Hillebrands (Kaiserslautern)Claudine Lacroix (Grenoble)Lluís Mañosa (Barcelona)María del Carmen Muñoz (Madrid)Bernard Raveau (Caen)Pedro Schlottmann (Tallahassee)Frank Steglich (Dresden)Oliver Waldmann (Freiburg) Invited speakers within symposia: R Ahuja (Uppsala)A Kirilyuk (Nijmegen) M Albrecht (Vienna)L Theil Kuhn (Roskilde) K Bärner (Göttingen)J Liu (Dresden) U Bovensiepen (Duisburg)G Lorusso (Modena) V Buchelnikov (Chelyabinsk)M M Maska (Katowice) B Chevalier (Bordeaux)Y Mukovskii (Moscow) O Chubykalo-Fesenko (Madrid)M Pannetier-Lecoeur (Saclay) A V Chumak (Kaiserslautern)G Papavassiliou (Athens) J M D Coey (Dublin)K R Pirota (Campinas) B Dabrowski (DeKalb)P Przyslupski (Warszawa) S Das (Aveiro)M Reiffers (Košice) A del Moral (Zaragoza)K Sandeman (London) V E Demidov (Muenster)D Sander (Halle) B Djafari-Rouhani (Lille)M Sawicki (Sendai/Warsaw) H A Dürr (Menlo Park)J Schaefer (Würzburg) J Fassbender (Dresden)H Schmidt (Wetzikon) J Fontcuberta (Barcelona)J Spałek (Kraków) V Garcia (Orsay)L Straka (Helsinki) J N Gonçalves (Aveiro)A Szewczyk (Warszawa) M E Gruner (Duisburg)Y Taguchi (Wako) G Gubbiotti (Perugia)A Thiaville

  3. The Mineral Physics Committee

    Science.gov (United States)

    Mineral Physics Committee members for the period July 1, 1986, to J ne 30, 1988, have been announced. They are Murli H. Manghnani (Hawaii Institute of Geophysics, Honolulu), and Orson L. Anderson (University of California, Los Angeles), Thomas J. Ahrens (California Institute of Technology, Pasadena, Calif.), Subir K. Banerjee (University of Minnesota, Minneapolis), William A. Bassett (Cornell University, Ithaca, N.Y.), Gordon E. Brown, Jr. (Stanford University, Stanford, Calif.), Michael Brown (University of Washington, Seattle), Robert M. Hazen (Geophysical Laboratory, Washington, D.C.), Raymond F. Jeanloz (University of California, Berkeley), Robert C. Liebermann (State University of New York (SUNY),(Stony Brook), Alexandra Navrotsky (Princeton University, Princeton, N.J.), Robert N. Schock (Lawrence Livermore National Laboratory, Livermore, Calif.), and Donald J. Weidner (SUNY Stony Brook).

  4. Powder Metallurgy of Uranium Alloy Fuels for TRU-Burning Reactors Final Technical Report

    International Nuclear Information System (INIS)

    McDeavitt, Sean M.

    2011-01-01

    Overview Fast reactors were evaluated to enable the transmutation of transuranic isotopes generated by nuclear energy systems. The motivation for this was that TRU isotopes have high radiotoxicity and relatively long half-lives, making them unattractive for disposal in a long-term geologic repository. Fast reactors provide an efficient means to utilize the energy content of the TRUs while destroying them. An enabling technology that requires research and development is the fabrication metallic fuel containing TRU isotopes using powder metallurgy methods. This project focused upon developing a powder metallurgical fabrication method to produce U-Zr-transuranic (TRU) alloys at relatively low processing temperatures (500 C to 600 C) using either hot extrusion or alpha-phase sintering for charecterization. Researchers quantified the fundamental aspects of both processing methods using surrogate metals to simulate the TRU elements. The process produced novel solutions to some of the issues relating to metallic fuels, such as fuel-cladding chemical interactions, fuel swelling, volatility losses during casting, and casting mold material losses. Workscope There were two primary tasks associated with this project: (1) Hot working fabrication using mechanical alloying and extrusion - Design, fabricate, and assemble extrusion equipment - Extrusion database on DU metal - Extrusion database on U-10Zr alloys - Extrusion database on U-20xx-10Zr alloys - Evaluation and testing of tube sheath metals (2) Low-temperature sintering of U alloys - Design, fabricate, and assemble equipment - Sintering database on DU metal - Sintering database on U-10Zr alloys - Liquid assisted phase sintering on U-20xx-10Zr alloys Appendices Outline Appendix A contains a Fuel Cycle Research and Development (FCR and D) poster and contact presentation where TAMU made primary contributions. Appendix B contains MSNE theses and final defense presentations by David Garnetti and Grant Helmreich outlining the

  5. Powder Metallurgy of Uranium Alloy Fuels for TRU-Burning Reactors Final Technical Report

    Energy Technology Data Exchange (ETDEWEB)

    McDeavitt, Sean M

    2011-04-29

    Overview Fast reactors were evaluated to enable the transmutation of transuranic isotopes generated by nuclear energy systems. The motivation for this was that TRU isotopes have high radiotoxicity and relatively long half-lives, making them unattractive for disposal in a long-term geologic repository. Fast reactors provide an efficient means to utilize the energy content of the TRUs while destroying them. An enabling technology that requires research and development is the fabrication metallic fuel containing TRU isotopes using powder metallurgy methods. This project focused upon developing a powder metallurgical fabrication method to produce U-Zr-transuranic (TRU) alloys at relatively low processing temperatures (500ºC to 600ºC) using either hot extrusion or alpha-phase sintering for charecterization. Researchers quantified the fundamental aspects of both processing methods using surrogate metals to simulate the TRU elements. The process produced novel solutions to some of the issues relating to metallic fuels, such as fuel-cladding chemical interactions, fuel swelling, volatility losses during casting, and casting mold material losses. Workscope There were two primary tasks associated with this project: 1. Hot working fabrication using mechanical alloying and extrusion • Design, fabricate, and assemble extrusion equipment • Extrusion database on DU metal • Extrusion database on U-10Zr alloys • Extrusion database on U-20xx-10Zr alloys • Evaluation and testing of tube sheath metals 2. Low-temperature sintering of U alloys • Design, fabricate, and assemble equipment • Sintering database on DU metal • Sintering database on U-10Zr alloys • Liquid assisted phase sintering on U-20xx-10Zr alloys Appendices Outline Appendix A contains a Fuel Cycle Research & Development (FCR&D) poster and contact presentation where TAMU made primary contributions. Appendix B contains MSNE theses and final defense presentations by David Garnetti and Grant Helmreich

  6. The beginning of metallurgy in the southern Levant: a late 6th millennium CalBC copper awl from Tel Tsaf, Israel.

    Science.gov (United States)

    Garfinkel, Yosef; Klimscha, Florian; Shalev, Sariel; Rosenberg, Danny

    2014-01-01

    The beginning of metallurgy in the ancient Near East attracts much attention. The southern Levant, with the rich assemblage of copper artifacts from the Nahal Mishmar cave and the unique gold rings of the Nahal Qanah cave, is regarded as a main center of early metallurgy during the second half of the 5th millennium CalBC. However, a recently discovered copper awl from a Middle Chalcolithic burial at Tel Tsaf, Jordan Valley, Israel, suggests that cast metal technology was introduced to the region as early as the late 6th millennium CalBC. This paper examines the chemical composition of this item and reviews its context. The results indicate that it was exported from a distant source, probably in the Caucasus, and that the location where it was found is indicative of the social status of the buried individual. This rare finding indicates that metallurgy was first diffused [corrected] to the southern Levant through exchange networks and only centuries later involved local productionThis copper awl, the earliest metal artifact found in the southern Levant, indicates that the elaborate Late Chalcolithic metallurgy developed from a more ancient tradition.

  7. [CHEMICAL AIR POLLUTION OF THE OCCUPATIONAL ENVIRONMENT AS A FACTOR FOR PROFESSIONAL RISK FOR WORKERS OF MAIN OCCUPATIONS IN THE COPPER AND NICKEL METALLURGY].

    Science.gov (United States)

    Lipatov, G Ia; Adrianovskiĭ, V I; Gogoleva, O I

    2015-01-01

    There are presented the results of hygienic researches of the harmful substances content in the air of the working area ofthe copper and nickel metallurgy. Sulfur-containing gases (primarily sulfur dioxide), to the effects of which there are exposed workers of drying, smelting, converter conversion, are shown to play a leading role among professional factors.

  8. 77 FR 64576 - Shipping Coordinating Committee; Notice of Committee Meeting

    Science.gov (United States)

    2012-10-22

    ... Correspondence Group (ISCG) work. --E-business possibilities for the facilitation of maritime traffic. A...-Chairman for 2012. --Any other business. --Consideration of the report of the Committee on its thirty...

  9. 77 FR 28923 - Shipping Coordinating Committee; Notice of Committee Meeting

    Science.gov (United States)

    2012-05-16

    ... Session of the International Maritime Organization's (IMO) Sub-Committee on Safety of Navigation to be... --Election of Chairman and Vice-Chairman for 2013 --Any other business --Report to the Maritime Safety...

  10. Nuclear Safety advisory committee (NSAC)

    International Nuclear Information System (INIS)

    1999-01-01

    The NNSA convened the 16th NSAC meeting in 1999. The Committee listened to the report by the NNSA relating to the fault of core barrel at the QNPP. And also the NNSA convened the 17th NSAC meeting in Beijing. The Committee listened to the report by the NNSA relating to the review and assessment on the application of CP at the JTNPP and discussed on the granting of CP and the related license conditions at the JTNPP. The Sub-Committee of NSAC of the NNSA on siting convened and enlarged meeting for a consulting with the domestic experts on the issue of seismic response spectrum in design at the JTNPP

  11. Introduction and Committees

    Science.gov (United States)

    Angelova, Maia; Zakrzewski, Wojciech; Hussin, Véronique; Piette, Bernard

    2011-03-01

    This volume contains contributions to the XXVIIIth International Colloquium on Group-Theoretical Methods in Physics, the GROUP 28 conference, which took place in Newcastle upon Tyne from 26-30 July 2010. All plenary and contributed papers have undergone an independent review; as a result of this review and the decisions of the Editorial Board most but not all of the contributions were accepted. The volume is organised as follows: it starts with notes in memory of Marcos Moshinsky, followed by contributions related to the Wigner Medal and Hermann Weyl prize. Then the invited talks at the plenary sessions and the public lecture are published followed by contributions in the parallel and poster sessions in alphabetical order. The Editors:Maia Angelova, Wojciech Zakrzewski, Véronique Hussin and Bernard Piette International Advisory Committee Michael BaakeUniversity of Bielefeld, Germany Gerald DunneUniversity of Connecticut, USA J F (Frank) GomesUNESP, Sao Paolo, Brazil Peter HanggiUniversity of Augsburg, Germany Jeffrey C LagariasUniversity of Michigan, USA Michael MackeyMcGill University, Canada Nicholas MantonCambridge University, UK Alexei MorozovITEP, Moscow, Russia Valery RubakovINR, Moscow, Russia Barry SandersUniversity of Calgary, Canada Allan SolomonOpen University, Milton Keynes, UK Christoph SchweigertUniversity of Hamburg, Germany Standing Committee Twareque AliConcordia University, Canada Luis BoyaSalamanca University, Spain Enrico CeleghiniFirenze University, Italy Vladimir DobrevBulgarian Academy of Sciences, Bulgaria Heinz-Dietrich DoebnerHonorary Member, Clausthal University, Germany Jean-Pierre GazeauChairman, Paris Diderot University, France Mo-Lin GeNankai University. China Gerald GoldinRutgers University, USA Francesco IachelloYale University, USA Joris Van der JeugtGhent University, Belgium Richard KernerPierre et Marie Curie University, France Piotr KielanowskiCINVESTAV, Mexico Alan KosteleckyIndiana University, USA Mariano del Olmo

  12. Assessment of heavy metals exposure, noise and thermal safety in the ambiance of a vacuum metallurgy separation system for recycling heavy metals from crushed e-wastes.

    Science.gov (United States)

    Zhan, Lu; Xu, Zhenming

    2014-12-01

    Vacuum metallurgy separation (VMS) is a technically feasible method to recover Pb, Cd and other heavy metals from crushed e-wastes. To further determine the environmental impacts and safety of this method, heavy metals exposure, noise and thermal safety in the ambiance of a vacuum metallurgy separation system are evaluated in this article. The mass concentrations of total suspended particulate (TSP) and PM10 are 0.1503 and 0.0973 mg m(-3) near the facilities. The concentrations of Pb, Cd and Sn in TSP samples are 0.0104, 0.1283 and 0.0961 μg m(-3), respectively. Health risk assessments show that the hazard index of Pb is 3.25 × 10(-1) and that of Cd is 1.09 × 10(-1). Carcinogenic risk of Cd through inhalation is 1.08 × 10(-5). The values of the hazard index and risk indicate that Pb and Cd will not cause non-cancerous effects or carcinogenic risk on workers. The noise sources are mainly the mechanical vacuum pump and the water cooling pump. Both of them have the noise levels below 80 dB (A). The thermal safety assessment shows that the temperatures of the vacuum metallurgy separation system surface are all below 303 K after adopting the circulated water cooling and heat insulation measures. This study provides the environmental information of the vacuum metallurgy separation system, which is of assistance to promote the industrialisation of vacuum metallurgy separation for recovering heavy metals from e-wastes. © The Author(s) 2014.

  13. Mechanical Behaviors of Friction Stir Spot Welded Joints of Dissimilar Ferrous Alloys under Opening-Dominant Combined Loads

    Directory of Open Access Journals (Sweden)

    Md. Abu Mowazzem Hossain

    2014-01-01

    Full Text Available Mechanical properties and failure behaviors of friction stir spot welded (FSSW joints of two dissimilar ferrous alloys, cold-rolled carbon steel (SPCC and 409L stainless steel (SUS 409L, are investigated under opening-dominant combined loads. The texture of dissimilar FSSW joints depends on the upper sheet material. The failure contours for the FSSW joints under combined loads are constructed in terms of the axial load and shear load by modifying existing failure criteria for resistance spot welds. The shape of the failure contour also depends on the upper sheet material. The failure contours are nearly elliptic in shape when the upper sheet is SPCC and are relatively straight lines when the upper sheet is SUS 409L.

  14. Surface chemistry, microstructure and friction properties of some ferrous-base metallic glasses at temperatures to 750 C

    Science.gov (United States)

    Miyoshi, K.; Buckley, D. H.

    1982-01-01

    X-ray photoelectron spectroscopy analysis, transmission electron microscopy, diffraction studies, and sliding friction experiments were conducted with ferrous-base metallic glasses in sliding contact with aluminum oxide at temperatures from room to 750 C in a vacuum of 30 nPa. The results indicate that there is a significant temperature influence on the friction properties, surface chemistry, and microstructure of metallic glasses. The relative concentrations of the various constituents at the surface of the sputtered specimens were very different from the normal bulk compositions. Contaminants can come from the bulk of the material to the surface upon heating and impart boric oxide and silicon oxide at 350 C and boron nitride above 500 C. The coefficient of friction increased with increasing temperature to 350 C. Above 500 C the coefficient of friction decreased rapidly. The segregation of contaminants may be responsible for the friction behavior.

  15. The dosimetry of 3 MeV and 14 MeV neutrons with the ferrous sulphate solution

    International Nuclear Information System (INIS)

    Pejuan, A.

    1980-03-01

    The aim of the present work is to determine the G value of a standard ferrous sulphate solution for neutrons with mean energies of 3 MeV and 14 MeV. The number of the transformed Fe ions is evaluated by means of a spectrophotometrical procedure and the absorbed energy is determined by applying the ionometrical method. Especial attention is payed to the calculation of the mean total dose in the irradiated sample taking radiation attenuation into account. For this purpose the spatial distribution of absorbed energy within the probe is determined. Further, it is investigated how the fraction of the γ component in the total absorbed dose varies in the sample, in order to evaluate its mean value, which is needed for the final determination of the G value for the neutron component. (orig.) [de

  16. Structure and catalytic activities of ferrous centers confined on the interface between carbon nanotubes and humic acid

    Science.gov (United States)

    Wang, Bing; Zhou, Xiaoyan; Wang, Dongqi; Yin, Jun-Jie; Chen, Hanqing; Gao, Xingfa; Zhang, Jing; Ibrahim, Kurash; Chai, Zhifang; Feng, Weiyue; Zhao, Yuliang

    2015-01-01

    Preparation of heterogeneous catalysts with active ferrous centers is of great significance for industrial and environmental catalytic processes. Nanostructured carbon materials (NCM), which possess free-flowing π electrons, can coordinate with transition metals, provide a confinement environment for catalysis, and act as potential supports or ligands to construct analogous complexes. However, designing such catalysts using NCM is still seldom studied to date. Herein, we synthesized a sandwich structured ternary complex via the coordination of Fe-loaded humic acid (HA) with C&z.dbd;C bonds in the aromatic rings of carbon nanotubes (CNTs), in which the O/N-Fe-C interface configuration provides the confinement environment for the ferrous sites. The experimental and theoretical results revealed octahedrally/tetrahedrally coordinated geometry at Fe centers, and the strong hybridization between CNT C π* and Fe 3d orbitals induces discretization of the atomic charges on aromatic rings of CNTs, which facilitates O2 adsorption and electron transfer from carbon to O2, which enhances O2 activation. The O2 activation by the novel HA/Fe-CNT complex can be applied in the oxidative degradation of phenol red (PR) and bisphenol A (BPA) in aqueous media.Preparation of heterogeneous catalysts with active ferrous centers is of great significance for industrial and environmental catalytic processes. Nanostructured carbon materials (NCM), which possess free-flowing π electrons, can coordinate with transition metals, provide a confinement environment for catalysis, and act as potential supports or ligands to construct analogous complexes. However, designing such catalysts using NCM is still seldom studied to date. Herein, we synthesized a sandwich structured ternary complex via the coordination of Fe-loaded humic acid (HA) with C&z.dbd;C bonds in the aromatic rings of carbon nanotubes (CNTs), in which the O/N-Fe-C interface configuration provides the confinement environment for the

  17. Titrimetric determination of uranium in low-grade ores by the ferrous ion-phosphoric acid reduction method

    International Nuclear Information System (INIS)

    Hitchen, A.; Zechanowitsch, G.

    1980-01-01

    The modification and extension of the U.S.A.E.C. ferrous ion-phosphoric acid reduction method for the determination of uranium in high-grade or relatively pure material to a method for the determination of uranium with a high accuracy and precision, in ores containing 0.004 to 7% U is described. It is simple, rapid and requires no prior separations from elements that, in other methods, frequently interfere. For sample materials having very high concentrations of interfering elements, a prior concentration step using extraction with tri-n-octylphosphine oxide is described, but it is shown that, for most low-grade ores, this step is unnecessary. (author)

  18. Effects of rapid, high-dose, elevated temperature ion implantation on the microstructure and tribology of ferrous surfaces

    Science.gov (United States)

    Williamson, D. L.; Wei, R.; Wilbur, P. J.

    1991-05-01

    High-current, broad-beam ion implantation at 60 keV using a relatively simple system produces elevated target temperatures and results in remarkable enhancements in the wear resistance of ferrous materials compared to lower implantation temperatures. Effects of N, C and O implantation into AISI 304 stainless steel at 200 and 400°C on the microstructure and tribology are evaluated by conversion electron Mössbauer spectroscopy, X-ray diffraction, and a specially designed pin-on-disc tribotester. C and N implantation at 400°C yields unusually thick layers of austenite containing high concentrations of C and N in interstitial solid solution thereby accounting for the enhanced mechanical properties. O implantation at 400°C results in Fe 2O 3-like oxide rather than O in solid solution so a dispersion strengthening of the surface layer is suggested.

  19. Determination of dislocation density by electron backscatter diffraction and X-ray line profile analysis in ferrous lath martensite

    International Nuclear Information System (INIS)

    Berecz, Tibor; Jenei, Péter; Csóré, András; Lábár, János; Gubicza, Jenő

    2016-01-01

    The microstructure and the dislocation density in as-quenched ferrous lath martensite were studied by different methods. The blocks, packets and variants formed due to martensitic transformation were identified and their sizes were determined by electron backscatter diffraction (EBSD). Concomitant transmission electron microscopy (TEM) investigation revealed that the laths contain subgrains with the size between 50 and 100 nm. A novel evaluation procedure of EBSD images was elaborated for the determination of the density and the space distribution of geometrically necessary dislocations from the misorientation distribution. The total dislocation density obtained by X-ray diffraction line profile analysis was in good agreement with the value determined by EBSD, indicating that the majority of dislocations formed due to martensitic transformation during quenching are geometrically necessary dislocations.

  20. Comparison of efficacy of ferrous and iron polymaltose salts in the treatment of childhood iron deficiency anemia

    International Nuclear Information System (INIS)

    Marwat, I.U.; Hassan, K.A.; Javed, T.; Chishti, A.L.

    2013-01-01

    Iron deficiency of anemia (IDA) is defined as reduced number of red blood cells, and / or reduced concentration hemoglobin (Hb) due to deficiency of iron. Treatment involves dietary modifications and inorganic iron salt supplements like ferrous sulfate (FS) or Iron polymaltose complex (IPC). The decision to select either drug rests on therapeutic efficacy, untoward side effects; cost of complete course, patient's compliance and discretion of physician. Both drugs can be prescribed in oral form. This study aimed at comparing the efficacy of two iron preparations (ferrous sulphate and iron polymaltose complex salts) in childhood iron deficiency anemia. Objective: To compare the efficacy of Ferrous Sulphate and Iron Polymaltose Complex salts in the treatment of childhood Iron Deficiency Anemia. Methodology: This randomized controlled trial was conducted at Department of Pediatric Medicine Unit-II Mayo Hospital, Lahore, for a period of 6 months. One hundred and fifty children aged 6 months to 5 years suffering from iron deficiency anemia were selected and randomly divided into two groups of 75 each (Group A and B prescribed FS and IPC respectively). Results were analyzed in terms of rise in Hb from the baseline after three months. Increase in Hb level 2 gm/dl after three months of treatment was considered as effective. Results were analyzed by SPSS version 17. Efficacy of both the drugs, was compared by chi square test. P value 0.05 was accepted as significant. Results: There were 34 cases (22.7%) in 6-12 months age, 77 cases (51.3%) between 1-3 years age and 39 cases (26%) between 3-5 years age. The number of male and female children was 82 (54.7%) and 68 (45.3%) respectively. The baseline hemoglobin of all study cases was 6.64+-1.08 gm/dl (6.59+-1.13 gm/dl in Group A and 6.69+-1.04 gm/dl in Group B). At completion of therapy, the mean hemoglobin of all study cases was 9.15+-1.21 gm/dl (9.20+9-1.17 gm/dl in Group A and 9.11+-1.25 gm/dl in Group B). The difference