WorldWideScience

Sample records for feeder stagnation break

  1. Safty assessment of RUFIC fuel during the postulated accident of CANDU-6 feeder breaks

    Energy Technology Data Exchange (ETDEWEB)

    Lim, H. S.; Jung, J. Y.; Suk, H. C

    2001-07-01

    The safety assessment for the feeder breaks, as one of the postulated design basis events, was performed for a CANDU 6 reactor loaded with CANFLEX-RU fuel bundles. According to the assessment results, the fuel channel integrity, molten mass, and fission products release from failed fuel for the stagnation and off-stagnation feeder breaks are assured to be a more enhanced safety for CANFLEX-RU bundle, compared to the 37-element bundle. Particularly, the amounts of CANFLEX-RU's molten mass and fission products release prior to channel failure in the case of stagnation feeder break are significantly reduced by 35% and 40%, respectively, compared to those of the 37-element bundle. With only the results for the postulated accident of feeder breaks, it cannot be judged that the same conclusion can be applied to other design basis events. Therefore, other severe design basis events which would result in fuel failure should be assessed in further study.

  2. THERMOSS: a thermohydraulic model of flow stagnation in a horizontal fuel channel

    International Nuclear Information System (INIS)

    Gulshani, P.; Caplan, M.Z.; Spinks, N.J.

    1984-01-01

    Following a postulated inlet-side small break in the CANDU reactor, emergency coolant is injected to refull the horizontal fuel channels and remove the decay heat. As part of the accident analysis, the effects of loss of forced circulation during the accident are predicted. A break size exists for which, at the end of pump rundown, the break force balances the natural circulation force and the channel flow is reduced to near zero. The subcooled, stagnant channel condition is referred to as the standing-start condition. Subsequently, the channel coolant boils and stratifies. Eventually the steam flow from the channel heats up the endfitting to the saturation temperature and reaches the vertical feeder. The resulting buoyancy-induced flow then refills the channel. One dimensional, two-fluid conservation equations are solved in closed form to predict the duration of stagnation. In this calculation the channel water level is an important intermediate variable because it determines the amount of steam production

  3. Feeder replacement tooling and processes

    International Nuclear Information System (INIS)

    Mallozzi, R.; Goslin, R.; Pink, D.; Askari, A.

    2008-01-01

    Primary heat transport system feeder integrity has become a concern at some CANDU nuclear plants as a result of thinning caused by flow accelerated corrosion (FAC). Feeder inspections are indicating that life-limiting wall thinning can occur in the region between the Grayloc hub weld and second elbow of some outlet feeders. In some cases it has become necessary to replace thinned sections of affected feeders to restore feeder integrity to planned end of life. Atomic Energy of Canada Limited (AECL) and Babcock and Wilcox Canada Ltd. (B and W) have developed a new capability for replacement of single feeders at any location on the reactor face without impacting or interrupting operation of neighbouring feeders. This new capability consists of deploying trained crews with specialized tools and procedures for feeder replacements during planned outages. As may be expected, performing single feeder replacement in the congested working environment of an operational CANDU reactor face involves overcoming many challenges with respect to access to feeders, available clearances for tooling, and tooling operation and performance. This paper describes some of the challenges encountered during single feeder replacements and actions being taken by AECL and B and W to promote continuous improvement of feeder replacement tooling and processes and ensure well-executed outages. (author)

  4. Secular stagnation or stagnation policy? Steindl after Summers

    Directory of Open Access Journals (Sweden)

    Eckhard Hein

    2016-03-01

    Full Text Available The debate on secular stagnation suffers from vagueness and several shortcomings, which affect its economic policy implications. In this work we provide an alternative view on the advanced economies’ tendencies to stagnation, based on Josef Steindl’s contributions. Steindl’s pioneering 1952 book in particular is not prone to several problems that affect the current debate on secular stagnation. It does not rely on the dubious notion of an equilibrium real interest rate as the equilibrating force of saving and investment at full employment levels. Rather, it is based on the notion that modern capitalist economies face aggregate demand constraints, and that saving adjusts to investment through income growth and changes in capacity utilisation in the long run. Steindl’s treatment allows for potential growth to become endogenous to actual demand, and it seriously considers the role of institutions and power relationships for long-run growth. In illustrating Steindl’s contributions on this topic, the article presents an original model synthetizing the main points in particular concerning long run growth and stagnation. JEL codes: B22, E11, E12, E65, O11

  5. The stagnation of international law

    NARCIS (Netherlands)

    Pauwelyn, Joost; Wessel, Ramses A.; Wouters, Jan

    2012-01-01

    Traditional international law and its instruments are stagnating both in terms of quantity and quality. New, alternative forms of cross-border cooperation, in particular processes of informal international lawmaking, have emerged and gained prominence since the 2000s in response to an increasingly

  6. Solar wind stagnation near comets

    International Nuclear Information System (INIS)

    Galeev, A.A.; Cravens, T.E.; Gombosi, T.I.

    1983-03-01

    The nature of the solar wind flow near comets is examined analytically. In particular, the typical values for the stagnation pressure and magnetic barrier strength are estimated, taking into account the magnetic field line tension and the charge exchange cooling of the mass loaded solar wind. Knowledge of the strength of the magnetic barrier is required in order to determine the location of the contact discontinuity which separates the contaminated solar wind plasma and the outflowing plasma of the cometary ionosphere. (author)

  7. RELAP4 stagnation properties option

    International Nuclear Information System (INIS)

    DeYoung, T.L.

    1979-01-01

    The stagnation properties option in RELAP4/MOD6 was completely reviewed, from theoretical foundation to code application. The result of this investigation was the identification of a fundamental mismatch between the essentially homogeneous, equilibrium-based, RELAP4 code and the nonhomogeneous and/or nonequilibrium critical flow models imposed on the code. By continuously monitoring fluid Mach numbers and adjusting flow areas such that sonic velocity was never exceeded, the mismatch could be accommodated. This approach was implemented, found to work correctly, and will be incorporated into the MOD7 version of the code

  8. Approximate Model for Turbulent Stagnation Point Flow.

    Energy Technology Data Exchange (ETDEWEB)

    Dechant, Lawrence [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2016-01-01

    Here we derive an approximate turbulent self-similar model for a class of favorable pressure gradient wedge-like flows, focusing on the stagnation point limit. While the self-similar model provides a useful gross flow field estimate this approach must be combined with a near wall model is to determine skin friction and by Reynolds analogy the heat transfer coefficient. The combined approach is developed in detail for the stagnation point flow problem where turbulent skin friction and Nusselt number results are obtained. Comparison to the classical Van Driest (1958) result suggests overall reasonable agreement. Though the model is only valid near the stagnation region of cylinders and spheres it nonetheless provides a reasonable model for overall cylinder and sphere heat transfer. The enhancement effect of free stream turbulence upon the laminar flow is used to derive a similar expression which is valid for turbulent flow. Examination of free stream enhanced laminar flow suggests that the rather than enhancement of a laminar flow behavior free stream disturbance results in early transition to turbulent stagnation point behavior. Excellent agreement is shown between enhanced laminar flow and turbulent flow behavior for high levels, e.g. 5% of free stream turbulence. Finally the blunt body turbulent stagnation results are shown to provide realistic heat transfer results for turbulent jet impingement problems.

  9. in meat production III. Feeder - breeder dimorphism

    African Journals Online (AJOL)

    Feeder- breeder dimorphism is advantageous when large offspring for slaughter is obtained from small breeding animals. The effect of feeder- breeder dimorphism on herd efficiency is evaluated for terminal crossbreeding and growth modification by biotechnological or dietary means. Selection criteria for breeds or lines in ...

  10. A hybrid evolutionary algorithm for distribution feeder reconfiguration

    Indian Academy of Sciences (India)

    Ant colony optimization (ACO); distribution feeder reconfiguration; fuzzy adaptive particle swarm optimization (FAPSO). 1. Introduction. Radial configuration is popular in distribution networks because of the effective coordination between feeder's protection systems and lower short circuit currents. Distribution feeders.

  11. PHTS Feeders. Inspection and maintenance plan

    International Nuclear Information System (INIS)

    Hare, Michael G.

    1998-01-01

    Since the start up of station, feeder thickness measurements had been taken in accordance with CSA 285.4 at a location near the outlet headers. This location indicated that no significant amount of wall loss was taking place. This observation did not agree with the ever increasing reactor inlet header temperature as it was approaching the administrative limit of 270 deg. C for plant operation at full power. Feeder thickness measurements at the first bend downstream of the graylok in 1995 indicated that the wall loss was taking place at this location at a rate much faster than the feeders were designed for. Review of the existing stress analysis proved that the existing feeders were still fit for service, reanalysis obtained the minimum thickness allowed for the piping to operate at and an aggressive inspection campaign was laid out to determine the thinning mechanism. Various methodologies were used for inspection and a permanent, continuos ultrasonic inspection system was installed to assess process parameter changes on the thinning rate to determine a fix to the thinning problem or a method to minimize it. Analysis of the results is still ongoing. In January 1997, a leak was discovered in feeder S08 due to a crack in the first bend downstream of the graylok. An extensive investigation reveled that fuel channel S08 was unlocked at both ends, and parts of the feeder support structure was not in the design configuration. This led to a thorough inspection of all the feeder support system to ensure that it was returned to its design status. The inspections led to the development of the Guided Wave Method of feeder pipe inspection for cracking indications. The Guided Wave inspection of a total of 157 feeder pipes revealed no reportable indications of cracking. The combination of the ongoing outlet feeder wall thinning and the crack that developed in the outlet feeder of S08a caused the Point Lepreau Station and the nuclear industry to invest a great deal of research

  12. An RFID Based Smart Feeder for Hummingbirds.

    Science.gov (United States)

    Ibarra, Vicente; Araya-Salas, Marcelo; Tang, Yu-ping; Park, Charlie; Hyde, Anthony; Wright, Timothy F; Tang, Wei

    2015-12-16

    We present an interdisciplinary effort to record feeding behaviors and control the diet of a hummingbird species (Phaethornis longirostris, the long-billed hermit or LBH) by developing a Radio Frequency Identification (RFID) based smart feeder. The system contains an RFID reader, a microcontroller, and a servo-controlled hummingbird feeder opener; the system is presented as a tool for studying the cognitive ability of the LBH species. When equipped with glass capsule RFID tags (which are mounted on the hummingbird), the smart feeder can provide specific diets for predetermined sets of hummingbirds at the discretion of biologists. This is done by reading the unique RFID tag on the hummingbirds and comparing the ID number with the pre-programmed ID numbers stored in the smart feeder. The smart feeder records the time and ID of each hummingbird visit. The system data is stored in a readily available SD card and is powered by two 9 V batteries. The detection range of the system is approximately 9-11 cm. Using this system, biologists can assign the wild hummingbirds to different experimental groups and monitor their diets to determine if they develop a preference to any of the available nectars. During field testing, the smart feeder system has demonstrated consistent detection (when compared to detections observed by video-recordings) of RFID tags on hummingbirds and provides pre-designed nectars varying water and sugar concentrations to target individuals. The smart feeder can be applied to other biological and environmental studies in the future.

  13. Stagnation, Acceleration And Deceleration In Agricultural Production ...

    African Journals Online (AJOL)

    This study investigated the hypothesis of stagnation/acceleration/deceleration in agricultural production in Nigeria for the period 1970-2000 by fitting exponential trend equations to the output data of the country's 23 major agricultural commodities and computing compound annual growth rates of agricultural production.

  14. Aggregate demand, functional finance and secular stagnation

    DEFF Research Database (Denmark)

    Skott, Peter

    2016-01-01

    This paper makes three main points. Fiscal policy, first, may be needed in the long run to maintain full employment and avoid secular stagnation. If fiscal policy is used in this way, second, the long-run debt ratio depends (i) inversely on the rate of growth, (ii) inversely on government consump...

  15. Why did Danish women's life expectancy stagnate?

    DEFF Research Database (Denmark)

    Lindahl-Jacobsen, Rune; Oeppen, James; Rizzi, Silvia

    2016-01-01

    The general health status of a population changes over time, generally in a positive direction. Some generations experience more unfavourable conditions than others. The health of Danish women in the interwar generations is an example of such a phenomenon. The stagnation in their life expectancy ...

  16. Containership Traffic Optimization on Feeder Shipping Line

    Directory of Open Access Journals (Sweden)

    Drozhzhyn Oleksii

    2016-12-01

    Full Text Available This article is devoted to feeder containership traffic optimization on the trunk and feeder shipping lines. The optimization is fulfilled in case of the necessity of laden containers delivery between fixed pairs of ports as well as in case of the requirement not to exceed the vessel's capacity, taking into account her residual value during transition between feeder port lines. The paper takes into account uneven distribution of empty container equipment in ports of line and the solution is suggested considering the estimation of the empty TEU’s number which is subject to reposition.

  17. Technological Progress, Globalization, and Secular Stagnation

    Directory of Open Access Journals (Sweden)

    Popović Milenko

    2018-01-01

    Full Text Available After the 2008 crisis, despite economic recovery that started in 2009, the world economy has experienced a downward shift of its growth path and a consequent decline. As shown at the beginning of this paper, this shift and growth rate stagnation are totally attributable to the economic dynamics in developed economies, the USA and the EU. Explanations of this phenomenon can be divided into two large groups: explanations that belong to the demand side and those that belong to the supply side. The aim of this paper is to give a critical survey of the most important explanations for the ongoing growth stagnation in developed countries and consequently in the entire world economy. This ongoing prolonged stagnation can only be explained by looking at both, the demand and supply sides of the explanation, and particularly by taking a closer look at the interaction between aggregate demand and aggregate supply. In other words, secular stagnation manifests itself as a problem of the limitation of long run growth of aggregate demand. However, in order to explain the causes of those demand limitations, we have to undertake a careful analysis of the supply side dynamics, especially the dynamics of innovations, which bring us to circular and cumulative causation. In order to explain the numerous consequences of this stagnation and to solve some important puzzles, like the productivity paradox for example, a special emphasis is given to the analysis of deindustrialization and the consequent strange reoccurrence of a dual economy within most developed countries during the period of the IT revolution and hyper-globalization. It will also be shown that this new dual economy presents serious limitations for further technological advancement and economic development, quite contrary to the old dualism which contributed to an acceleration of economic growth.

  18. An Empirical Study on the Current Feeder Shipping Network Patterns among Malaysian Feeder Service Providers

    Directory of Open Access Journals (Sweden)

    Muhamad Nasir Rahmatdin

    2017-12-01

    Full Text Available Route network patterns have been investigated globally by many researchers, with the majority of studies only focussing on the liner shipping industry for long-distance services, and with less attention paid to the feeder services industry. The feeder services industry is important to enhance the economic sustainability and viability of feeder service providers and trade partners. The primary objectives of this paper were to study the focal economy points of feeder services in Malaysia and to demonstrate the type of network patterns practised by Malaysian feeder service providers. Accordingly, an empirical study was conducted through the cooperation of eight Malaysian feeder service providers via face-to-face interviews and port visits to understand the patterns of each shipping route deployed. Moreover, to demonstrate the network patterns of each feeder service provider, a route network model was designed. The main finding from this study found that Port Klang was the primary feeder hub port and focal economy point in Malaysia due to the highest number of feeder vessels entering the port. Furthermore, the type of route patterns applied by Malaysian feeder service providers were determined and categorised based on three models: 75% (basic model, 17.5% (butterfly model, and 7.5% (chain model collected data consisting of 40 service routes. This paper will assist future and existing feeder service providers in their planning and execution of the optimal service routes regarding their efficiency in servicing existing and future customers and promoting strategic and tactical allocation of shipping services to specific ports.

  19. Public debt, secular stagnation and functional finance

    DEFF Research Database (Denmark)

    Skott, Peter

    2016-01-01

    Fiscal policy and public debt may be required to maintain full employment and avoid secular stagnation. This conclusion emerges from a range of different models, including OLG specifications and stock-flow consistent (post-) Keynesian models. One of the determinants of the required long-run debt ...... consumption and the structure of taxation influence the required debt ratio and, paradoxically, austerity policies are counterproductive on their own terms: cuts in government consumption lead to an increase in the required level of debt....

  20. An RFID Based Smart Feeder for Hummingbirds

    Directory of Open Access Journals (Sweden)

    Vicente Ibarra

    2015-12-01

    Full Text Available We present an interdisciplinary effort to record feeding behaviors and control the diet of a hummingbird species (Phaethornis longirostris, the long-billed hermit or LBH by developing a Radio Frequency Identification (RFID based smart feeder. The system contains an RFID reader, a microcontroller, and a servo-controlled hummingbird feeder opener; the system is presented as a tool for studying the cognitive ability of the LBH species. When equipped with glass capsule RFID tags (which are mounted on the hummingbird, the smart feeder can provide specific diets for predetermined sets of hummingbirds at the discretion of biologists. This is done by reading the unique RFID tag on the hummingbirds and comparing the ID number with the pre-programmed ID numbers stored in the smart feeder. The smart feeder records the time and ID of each hummingbird visit. The system data is stored in a readily available SD card and is powered by two 9 V batteries. The detection range of the system is approximately 9–11 cm. Using this system, biologists can assign the wild hummingbirds to different experimental groups and monitor their diets to determine if they develop a preference to any of the available nectars. During field testing, the smart feeder system has demonstrated consistent detection (when compared to detections observed by video-recordings of RFID tags on hummingbirds and provides pre-designed nectars varying water and sugar concentrations to target individuals. The smart feeder can be applied to other biological and environmental studies in the future.

  1. Power budget analysis of dual/single feeder fiber WDMPON

    Science.gov (United States)

    Imtiaz, Waqas A.; Khan, Yousaf; Qamar, Affaq; Khan, Jehanzeb; Khan, Noaman Ahmed

    2014-03-01

    This paper investigates how to reduce the cost of wavelength division multiplexing passive optical network (WDMPON) by comparing the transmission performance of bidirectional single feeder fiber and dual feeder fiber. Comparison is performed on the basis of power budgeting and cost of both arrangements. Simulation results using Optisystem show that the performance of a single feeder fiber is almost equivalent to that of a dual feeder fiber. Therefore, the single feeder fiber WDM-PON can efficiently replace the dual feeder fiber WDM-PON with the minimum deterioration in system performance and reduction in cost.

  2. Energy-political stagnation or innovation

    International Nuclear Information System (INIS)

    Kitschelt, H.

    1982-01-01

    The author discusses the enquete report 1980. He makes an inventory for a political and sociological interpretation of the interim report between meaningful innovation and political insignificance as well as intellectual stagnation. The report is considered as an indicator for the transformation of the energy-political arena in the Federal Republic of Germany over the last years. ''Stagnation'' or ''innovation'' of the argumentation patterns in the report of the enquete commission relate to the question whether the analyses in that document are rather a brake or a motor to a shift of political perspectives in energy policy. A progress can be seen in the report regarding political debate about energy-options in the semi-official political spectrum of the Federal Republic of Germany, in as far as differring options of energy-political development are being acknowledged for the first time. At the same time, debate inside the commission directs the attention to issues of institutional policy in the energy sector. Considering the fights within the commission before the report was agreed on, it seems doubtful if its proposals for compromise will prove a sound political basis. The tensions inside the commission are just a first sign of the power conflicts due above all if the recommendations for energy conservation are intransigently carried out. (orig./HSCH) [de

  3. 7 CFR 58.625 - Fruit or syrup feeders.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 3 2010-01-01 2010-01-01 false Fruit or syrup feeders. 58.625 Section 58.625 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Standards....625 Fruit or syrup feeders. Fruit or syrup feeders inject flavoring material into the semi-frozen...

  4. Orality disorders in melancholia: acedia as stagnation

    Directory of Open Access Journals (Sweden)

    Ana Cecília Magtaz

    2012-09-01

    Full Text Available In this article valuable contributions by Lasègue, Freud and Abraham are discussed, as they are all indispensible to the understanding of orality disorders in melancholia. Although none of the above authors used the exact term "orality disorders," their understandings of both hysteria and melancholia are important in the debate surrounding the clinical treatment of these difficulties. Sadness is a common denominator for the authors, but contributions on acedia, the "noonday demon" mentioned by Agamben, are also important. Acedia is defined as stagnation, a desperate lack of vigor when faced with a wearying and demanding situation. Those who suffer from chronic acedia feel great inertia and are unable to envision a future. They see their creativity wane away, especially due to the painful isolation caused by what might be called anguished sadness - a denial of sadness through manic action.

  5. A bend thickness sensitivity study of Candu feeder piping

    International Nuclear Information System (INIS)

    Li, M.; Aggarwal, M.L.; Meysner, A.; Micelotta, C.

    2005-01-01

    In CANDU reactors, feeder bends close to the connection at the fuel channel may be subjected to the highest Flow Accelerated Corrosion (FAC) and stresses. Feeder pipe stress analysis is crucial in the life extension of aging CANDU plants. Typical feeder pipes are interconnected by upper link plates and spacers. It is well known that the stresses at the bends are sensitive to the local bend thicknesses. It is also known from the authors' study (Li and et al, 2005) that feeder inter linkage effect is significant and cannot be ignored. The field measurement of feeder bend thickness is difficult and may be subjected to uncertainty in accuracy. Hence, it is desirable to know how the stress on a subject feeder could be affected by the bend thickness variation of the neighboring feeders. This effect cannot be evaluated by the traditional 'single' feeder model approach. In this paper, the 'row' and 'combined' models developed in the previous study (Li and et al, 2005), which include the feeder interactions, are used to investigate the sensitivity of bend thickness. A series of random thickness bounded by maximum and minimum measured values were applied to feeders in the model. The results show that an individual feeder is not sensitive to the bend thickness variation of the remaining feeders in the model, but depends primarily on its own bend thickness. The highest stress at a feeder always occurs when the feeder has the smallest possible bend thickness. A minimum acceptable bend thickness for individual feeders can be computed by an iterative computing process. The dependency of field thickness measurement and the amount of required analysis work can be greatly reduced. (authors)

  6. Corrosion of CANDU outlet feeder pipes

    Energy Technology Data Exchange (ETDEWEB)

    Burrill, K.A.; Cheluget, E.L

    1999-02-01

    Recent inspections have indicated that carbon steel outlet feeder pipes in some CANDU reactors are experiencing wall loss near the exit from the reactor core. This phenomenon is not observed in inlet feeder pipes. Examination of a sample of pipe removed from a CANDU 6 reactor has indicated that the mechanism causing the wall loss is flow-accelerated corrosion (FAC), at rates higher than expected, but two orders of magnitude lower than those typically observed in secondary circuits of nuclear and conventional power plants. Although the CANDU reactor outlet feeder operating temperatures and the use of LiOH at a high pH should have ensured low corrosion rates, use of SA 106 Grade B carbon steel with a low chromium content resulted in some susceptibility to FAC. The main parameter influencing the rate of wall loss is the coolant velocity, with the bend angle playing a secondary role. A solubility-based mathematical model describing the effects of water chemistry and coolant hydrodynamics on the rate of FAC has been developed and has been recently improved by the empirical incorporation of the effect of electrochemical potential on the solubility of magnetite. Experiment and theory have indicated that the corrosion rates are lower at lower pH values within the permissible operating range. Experiments are being conducted to obtain more information on the effects of water chemistry and material composition on FAC. Current results support the predicted effects of pH and carbon steel chromium content on the FAC rate. Remedial measures implemented include operation of existing reactors at the lower end of the specified pH range and the specification of a minimum of 0.20 wt% Cr in the carbon steel of feeder pipes of future CANDU reactors. (author)

  7. Optical Transmission Schemes for GEO Feeder Links

    OpenAIRE

    Cowley, William; Giggenbach, Dirk; Mata Calvo, Ramon

    2014-01-01

    A novel transmission scheme for the forward link of a broadband satellite system that aims to avoid the need for feeder-link RF spectrum is described1. The hybrid scheme uses one or more optical uplinks from a hub station to geostationary satellite, plus one or more Ka band downlinks. The approach aims to retain the advantages of strong channel coding with high spectral efficiency, as used in recent high-speed digital video broadcast satellites, yet minimise on-boar...

  8. Pressurized feeder for biofuels; Paineistettu syoetin biopolttoaineille

    Energy Technology Data Exchange (ETDEWEB)

    Lundqvist, R.; Makkonen, P. [Foster Wheeler Energia Oy, Karhula (Finland). Karhula R and D Center

    1995-12-31

    A new type of pressurized piston feeder has been tested for further development of the IGCC concept. The project is funded by the Finnish Ministry of Trade and Industry. The objective has been to develop a substitute for lock-hopper systems, which are commercial, but far too expensive from an operational point of view, due to high inert gas consumption for pressurization. The new feeder system, which is of dual piston type, uses little inert gas, because the pressurization sequence is performed partially by the piston movement. The project comprised further development of the concept, mechanical testing under atmospheric and pressurized conditions and testing with wood chips, peat and coal at elevated pressures. The main concern has been the wear of seals and gaskets during long term operation and for this reason over 600 hours of testing has been carried out. The tests were carried out between May 1994 and January 1995 with wood chips, peat and coal mainly at 17 bar(a) pressure. During the operation, the system was fine-tuned, and generally, the testing was successful. At the early stage of the tests, the ring seal design was modified and several alternative seal constructions were tested. During the tests, the seal was developed further and improved. The present ring seal design has been proven reliable and it meets the commercial requirements. After the tests, the feeder system was inspected thoroughly and found to be in good condition. A commercially available concept of the feeder has been developed on the basis of the knowledge obtained during the test runs

  9. Improvement of automatic fish feeder machine design

    Science.gov (United States)

    Chui Wei, How; Salleh, S. M.; Ezree, Abdullah Mohd; Zaman, I.; Hatta, M. H.; Zain, B. A. Md; Mahzan, S.; Rahman, M. N. A.; Mahmud, W. A. W.

    2017-10-01

    Nation Plan of action for management of fishing is target to achieve an efficient, equitable and transparent management of fishing capacity in marine capture fisheries by 2018. However, several factors influence the fishery production and efficiency of marine system such as automatic fish feeder machine could be taken in consideration. Two latest fish feeder machines have been chosen as the reference for this study. Based on the observation, it has found that the both machine was made with heavy structure, low water and temperature resistance materials. This research’s objective is to develop the automatic feeder machine to increase the efficiency of fish feeding. The experiment has conducted to testing the new design of machine. The new machine with maximum storage of 5 kg and functioning with two DC motors. This machine able to distribute 500 grams of pellets within 90 seconds and longest distance of 4.7 meter. The higher speed could reduce time needed and increase the distance as well. The minimum speed range for both motor is 110 and 120 with same full speed range of 255.

  10. On stagnation pressure increases in calorically perfect, ideal gases

    International Nuclear Information System (INIS)

    Williams, D.M.; Kamenetskiy, D.S.; Spalart, P.R.

    2016-01-01

    Highlights: • Unaveraged transport equation is obtained for the stagnation pressure. • Reynolds-averaged transport equation is obtained for the stagnation pressure. • Transport equations apply to compressible flow of calorically perfect, ideal gas. • Stagnation pressure is shown to be capable of naturally or artificially increasing. • Spurious overshoots likely in shear layers displaying convex streamline curvature. - Abstract: When stagnation pressure rises in a natural or numerically simulated flow it is frequently a cause for concern, as one usually expects viscosity and turbulence to cause stagnation pressure to decrease. In fact, if stagnation pressure increases, one may suspect measurement or numerical errors. However, this need not be the case, as the laws of nature do not require that stagnation pressure continually decreases. In order to help clarify matters, the objective of this work is to understand the conditions under which stagnation pressure will rise in the unsteady/steady flows of compressible, viscous, calorically perfect, ideal gases. Furthermore, at a more practical level, the goal is to understand the conditions under which stagnation pressure will increase in flows simulated with the Reynolds averaged Navier–Stokes equations and eddy-viscosity turbulence models. In order to provide an improved understanding of increases in stagnation pressure for both these scenarios, transport equations are derived that govern its behavior in the unaveraged and Reynolds averaged settings. These equations are utilized to precisely determine the relationship between changes in stagnation pressure and zeroth, first, and second derivatives of fundamental flow quantities. Furthermore, these equations are utilized to demonstrate the relationship between changes in stagnation pressure and fundamental non-dimensional quantities that govern the conductivity, viscosity, and compressibility of the flow. In addition, based on an analysis of the Reynolds

  11. Inertioelastic Flow Instability at a Stagnation Point

    Science.gov (United States)

    Burshtein, Noa; Zografos, Konstantinos; Shen, Amy Q.; Poole, Robert J.; Haward, Simon J.

    2017-10-01

    A number of important industrial applications exploit the ability of small quantities of high molecular weight polymer to suppress instabilities that arise in the equivalent flow of Newtonian fluids, a particular example being turbulent drag reduction. However, it can be extremely difficult to probe exactly how the polymer acts to, e.g., modify the streamwise near-wall eddies in a fully turbulent flow. Using a novel cross-slot flow configuration, we exploit a flow instability in order to create and study a single steady-state streamwise vortex. By quantitative experiment, we show how the addition of small quantities (parts per million) of a flexible polymer to a Newtonian solvent dramatically affects both the onset conditions for this instability and the subsequent growth of the axial vorticity. Complementary numerical simulations with a finitely extensible nonlinear elastic dumbbell model show that these modifications are due to the growth of polymeric stress within specific regions of the flow domain. Our data fill a significant gap in the literature between the previously reported purely inertial and purely elastic flow regimes and provide a link between the two by showing how the instability mode is transformed as the fluid elasticity is varied. Our results and novel methods are relevant to understanding the mechanisms underlying industrial uses of weakly elastic fluids and also to understanding inertioelastic instabilities in more confined flows through channels with intersections and stagnation points.

  12. Breaking Bat

    Science.gov (United States)

    Aguilar, Isaac-Cesar; Kagan, David

    2013-01-01

    The sight of a broken bat in Major League Baseball can produce anything from a humorous dribbler in the infield to a frightening pointed projectile headed for the stands. Bats usually break at the weakest point, typically in the handle. Breaking happens because the wood gets bent beyond the breaking point due to the wave sent down the bat created…

  13. Impact of flow accelerated corrosion (FAC) on feeder refurbishment planning

    International Nuclear Information System (INIS)

    Jyrkama, M.; Pandey, M.

    2010-01-01

    Feeder wall thinning due to flow accelerated corrosion (FAC) may result in a large number of feeder replacements in the future. In this study, the process of FAC is modelled using a probabilistic approach and used to predict the expected number of degraded feeders and their replacements in the future. Because of the high cost associated with feeder replacements, it may be optimal to replace the entire feeder population during a single refurbishment outage when the unit cost of replacement is likely to be less. The results of this study demonstrate, however, that the unit cost of feeder replacement must be sufficiently lower than the standard replacement cost and the refurbishment performed at an optimal time to realize the economic benefits associated with the refurbishment. (author)

  14. Risk-informed prediction of feeder end of life

    International Nuclear Information System (INIS)

    Jyrkama, M.; Pandey, M.

    2011-01-01

    The operating life of feeder piping is negatively impacted by flow accelerated corrosion (FAC). In this study, an assessment of a large set of inspection data reveals that FAC in feeders is a relatively stationary process, with variability only at the local scale. Given the added uncertainty from inspection coverage, a new method for estimating the thinning rate and feeder EOL is developed using a probabilistic approach. The results of the study illustrate the benefits of the methodology in supporting risk-informed decision making at the station by quantifying the present and incremental risk in the feeder system over time. (author)

  15. Ornithologists by Design: Kindergarteners Design, Construct, and Evaluate Bird Feeders

    Science.gov (United States)

    Shorter, Angela; Segers, Marcia

    2016-01-01

    How can an engineer design a bird feeder that attracts many birds? This question resulted from kindergarten students' observations of the bird feeders in their school's bird sanctuary. The challenging question is the heart of project-based learning (PBL), a teaching strategy in which students tackle real-world problems and design projects to solve…

  16. Automation Selection and Sequencing of Traps for Vibratory Feeders

    DEFF Research Database (Denmark)

    Mathiesen, Simon; Ellekilde, Lars-Peter

    2017-01-01

    Vibratory parts feeders with mechanical orienting devices are used extensively in the assembly automation industry. Even so, the design process is based on trial-and-error approaches and is largely manual. In this paper, a methodology is presented for automatic design of this type of feeder...

  17. Colour preferences of UK garden birds at supplementary seed feeders

    Science.gov (United States)

    Rothery, Luke; Scott, Graham W.

    2017-01-01

    Supplementary feeding of garden birds generally has benefits for both bird populations and human wellbeing. Birds have excellent colour vision, and show preferences for food items of particular colours, but research into colour preferences associated with artificial feeders is limited to hummingbirds. Here, we investigated the colour preferences of common UK garden birds foraging at seed-dispensing artificial feeders containing identical food. We presented birds simultaneously with an array of eight differently coloured feeders, and recorded the number of visits made to each colour over 370 30-minute observation periods in the winter of 2014/15. In addition, we surveyed visitors to a garden centre and science festival to determine the colour preferences of likely purchasers of seed feeders. Our results suggest that silver and green feeders were visited by higher numbers of individuals of several common garden bird species, while red and yellow feeders received fewer visits. In contrast, people preferred red, yellow, blue and green feeders. We suggest that green feeders may be simultaneously marketable and attractive to foraging birds. PMID:28212435

  18. Configuration System for Simulation Based Design of Vibratory Bowl Feeders

    DEFF Research Database (Denmark)

    Natapon Hansen, Michael; Mathiesen, Simon; Ellekilde, Lars-Peter

    2016-01-01

    Vibratory bowl feeders are still among the most commonly used production equipment for automated part feeding, where parts are correctly oriented for further manipulation by being conveyed through a set of orienting devices. Designing vibratory bowl feeders involves selecting and sequencing...

  19. Colour preferences of UK garden birds at supplementary seed feeders.

    Directory of Open Access Journals (Sweden)

    Luke Rothery

    Full Text Available Supplementary feeding of garden birds generally has benefits for both bird populations and human wellbeing. Birds have excellent colour vision, and show preferences for food items of particular colours, but research into colour preferences associated with artificial feeders is limited to hummingbirds. Here, we investigated the colour preferences of common UK garden birds foraging at seed-dispensing artificial feeders containing identical food. We presented birds simultaneously with an array of eight differently coloured feeders, and recorded the number of visits made to each colour over 370 30-minute observation periods in the winter of 2014/15. In addition, we surveyed visitors to a garden centre and science festival to determine the colour preferences of likely purchasers of seed feeders. Our results suggest that silver and green feeders were visited by higher numbers of individuals of several common garden bird species, while red and yellow feeders received fewer visits. In contrast, people preferred red, yellow, blue and green feeders. We suggest that green feeders may be simultaneously marketable and attractive to foraging birds.

  20. Stagnation morphology in Magnetized Liner Inertial Fusion experiments

    Science.gov (United States)

    Gomez, M. R.; Harding, E. C.; Ampleford, D. J.; Jennings, C. A.; Awe, T. J.; Chandler, G. A.; Glinsky, M. E.; Hahn, K. D.; Hansen, S. B.; Jones, B.; Knapp, P. F.; Martin, M. R.; Peterson, K. J.; Rochau, G. A.; Ruiz, C. L.; Schmit, P. F.; Sinars, D. B.; Slutz, S. A.; Weis, M. R.; Yu, E. P.

    2017-10-01

    In Magnetized Liner Inertial Fusion (MagLIF) experiments on the Z facility, an axial current of 15-20 MA is driven through a thick metal cylinder containing axially-magnetized, laser-heated deuterium fuel. The cylinder implodes, further heating the fuel and amplifying the axial B-field. Instabilities, such as magneto-Rayleigh-Taylor, develop on the exterior of the liner and may feed through to the inner surface during the implosion. Monochromatic x-ray emission at stagnation shows the stagnation column is quasi-helical with axial variations in intensity. Recent experiments demonstrated that the stagnation emission structure changed with modifications to the target wall thickness. Additionally, applying a thick dielectric coating to the exterior of the target modified the stagnation column. A new version of the x-ray self-emission diagnostic has been developed to investigate stagnation with higher resolution. Sandia National Laboratories is a multi-mission laboratory managed and operated by National Technology & Engineering Solutions of Sandia, LLC., a wholly owned subsidiary of Honeywell International, Inc., for the U.S. Department of Energy's National Nuclear Security Administration under contract DE-NA0003525.

  1. A Novel Method of Statistical Line Loss Estimation for Distribution Feeders Based on Feeder Cluster and Modified XGBoost

    Directory of Open Access Journals (Sweden)

    Shouxiang Wang

    2017-12-01

    Full Text Available The estimation of losses of distribution feeders plays a crucial guiding role for the planning, design, and operation of a distribution system. This paper proposes a novel estimation method of statistical line loss of distribution feeders using the feeder cluster technique and modified eXtreme Gradient Boosting (XGBoost algorithm that is based on the characteristic data of feeders that are collected in the smart power distribution and utilization system. In order to enhance the applicability and accuracy of the estimation model, k-medoids algorithm with weighting distance for clustering distribution feeders is proposed. Meanwhile, a variable selection method for clustering distribution feeders is discussed, considering the correlation and validity of variables. This paper next modifies the XGBoost algorithm by adding a penalty function in consideration of the effect of the theoretical value to the loss function for the estimation of statistical line loss of distribution feeders. The validity of the proposed methodology is verified by 762 distribution feeders in the Shanghai distribution system. The results show that the XGBoost method has higher accuracy than decision tree, neural network, and random forests by comparison of Root Mean Square Error (RMSE, Mean Absolute Percentage Error (MAPE, and Absolute Percentage Error (APE indexes. In particular, the theoretical value can significantly improve the reasonability of estimated results.

  2. Behavior of a solar collector loop during stagnation

    DEFF Research Database (Denmark)

    Chen, Ziqian; Dragsted, Janne; Furbo, Simon

    2015-01-01

    A mathematical model simulating the emptying behavior of a pressurized solar collector loop with solar collectors with a good emptying behavior is developed and validated with measured data. The calculated results are in good agreement with the measured results. The developed simulation model...... is therefore suitable to determine the behavior of a solar collector loop during stagnation. A volume ratio R, which is the ratio of the volume of the vapour in the upper pipes of the solar collector loop during stagnation and the fluid content of solar collectors, is introduced to determine the mass...... of the collector fluid pushed into the expansion vessel during stagnation, Min. A correlation function for the mass Min and the volume ratio R for solar collector loops is obtained. The function can be used to determine a suitable size of expansion vessels for solar collector loops....

  3. MATLAB: break

    OpenAIRE

    2005-01-01

    Interactive Media Element This interactive tutorial on MATLAB covers the use of the break function. An example demonstrates how the break function affects a for loop with if instruction embedded in the loop. An example is provided with step-by-step animated explanation. The interactions involve entering MATLAB instructions and observing the outcomes. Self-check questions are provided to help learners determine their level of understanding of the content presented. EC1010 Introduction...

  4. A Dynamic and Heuristic Phase Balancing Method for LV Feeders

    Directory of Open Access Journals (Sweden)

    Samad Taghipour Boroujeni

    2016-01-01

    Full Text Available Due to the single-phase loads and their stochastic behavior, the current in the distribution feeders is not balanced. In addition, the single-phase loads are located in different positions along the LV feeders. So the amount of the unbalanced load and its location affect the feeder losses. An unbalanced load causes the feeder losses and the voltage drop. Because of time-varying behavior of the single-phase loads, phase balancing is a dynamic and combinatorial problem. In this research, a heuristic and dynamic solution for the phase balancing of the LV feeders is proposed. In this method, it is supposed that the loads’ tie could be connected to all phases through a three-phase switch. The aim of the proposed method is to make the feeder conditions as balanced as possible. The amount and the location of single-phase loads are considered in the proposed phase balancing method. Since the proposed method needs no communication interface or no remote controller, it is inexpensive, simple, practical, and robust. Applying this method provides a distributed and dynamic phase balancing control. In addition, the feasibility of reducing the used switches is investigated. The ability of the proposed method in the phase balancing of the LV feeders is approved by carrying out some simulations.

  5. Human induced pluripotent stem cells on autologous feeders.

    Directory of Open Access Journals (Sweden)

    Kazutoshi Takahashi

    Full Text Available BACKGROUND: For therapeutic usage of induced Pluripotent Stem (iPS cells, to accomplish xeno-free culture is critical. Previous reports have shown that human embryonic stem (ES cells can be maintained in feeder-free condition. However, absence of feeder cells can be a hostile environment for pluripotent cells and often results in karyotype abnormalities. Instead of animal feeders, human fibroblasts can be used as feeder cells of human ES cells. However, one still has to be concerned about the existence of unidentified pathogens, such as viruses and prions in these non-autologous feeders. METHODOLOGY/PRINCIPAL FINDINGS: This report demonstrates that human induced Pluripotent Stem (iPS cells can be established and maintained on isogenic parental feeder cells. We tested four independent human skin fibroblasts for the potential to maintain self-renewal of iPS cells. All the fibroblasts tested, as well as their conditioned medium, were capable of maintaining the undifferentiated state and normal karyotypes of iPS cells. Furthermore, human iPS cells can be generated on isogenic parental fibroblasts as feeders. These iPS cells carried on proliferation over 19 passages with undifferentiated morphologies. They expressed undifferentiated pluripotent cell markers, and could differentiate into all three germ layers via embryoid body and teratoma formation. CONCLUSIONS/SIGNIFICANCE: These results suggest that autologous fibroblasts can be not only a source for iPS cells but also be feeder layers. Our results provide a possibility to solve the dilemma by using isogenic fibroblasts as feeder layers of iPS cells. This is an important step toward the establishment of clinical grade iPS cells.

  6. Distribution feeder reconfiguration with refined genetic algorithm

    Energy Technology Data Exchange (ETDEWEB)

    Lin, W.-M.; Cheng, F.-S. [National Sun Yat-Sen University, Kaohsiung (China). Dept. of Electrical Engineering; Tsay, M.-T. [Cheng-Shiu Institute of Technology, Kaohsiung (China). Dept. of Electrical Engineering

    2000-11-01

    A refined genetic algorithm for a distribution feeder reconfiguration to reduce losses is presented. The problem is optimised in a stochastic searching manner similar to that of the conventional GA. The initial population is determined by opening the switches with the lowest current in every mesh derived in the optimal power flow (OPF), with all switches closed. Solutions provided by OPF are generally the optimum or near-optimal solutions for most cases, so prematurity could occur. To avoid prematurity, the conventional crossover and mutation scheme was refined by a competition mechanism. So the dilemma of choosing a proper probability for crossover and mutation can be avoided. The two processes were also combined into one to save computation time. Tabu lists with heuristic rules were also employed in the searching process to enhance performance. The new approach provides an overall switching decision instead of a successive pattern, which tends to converge to a local optimum. Many tests were conducted and the results have shown that RGA has advantages over many other previously developed algorithms. (author)

  7. Stability of stagnation via an expanding accretion shock wave

    Energy Technology Data Exchange (ETDEWEB)

    Velikovich, A. L.; Giuliani, J. L. [Plasma Physics Division, Naval Research Laboratory, Washington, DC 20375 (United States); Murakami, M. [Institute of Laser Engineering, Osaka University, Osaka 565-0871 (Japan); Taylor, B. D. [Laboratory for Computational Physics and Fluid Dynamics, Naval Research Laboratory, Washington, DC 20375 (United States); Zalesak, S. T. [Berkeley Research Associates, Beltsville, Maryland 20705 (United States); Iwamoto, Y. [Ehime University, Matsuyama, Ehime Pref. 790-8577 (Japan)

    2016-05-15

    Stagnation of a cold plasma streaming to the center or axis of symmetry via an expanding accretion shock wave is ubiquitous in inertial confinement fusion (ICF) and high-energy-density plasma physics, the examples ranging from plasma flows in x-ray-generating Z pinches [Maron et al., Phys. Rev. Lett. 111, 035001 (2013)] to the experiments in support of the recently suggested concept of impact ignition in ICF [Azechi et al., Phys. Rev. Lett. 102, 235002 (2009); Murakami et al., Nucl. Fusion 54, 054007 (2014)]. Some experimental evidence indicates that stagnation via an expanding shock wave is stable, but its stability has never been studied theoretically. We present such analysis for the stagnation that does not involve a rarefaction wave behind the expanding shock front and is described by the classic ideal-gas Noh solution in spherical and cylindrical geometry. In either case, the stagnated flow has been demonstrated to be stable, initial perturbations exhibiting a power-law, oscillatory or monotonic, decay with time for all the eigenmodes. This conclusion has been supported by our simulations done both on a Cartesian grid and on a curvilinear grid in spherical coordinates. Dispersion equation determining the eigenvalues of the problem and explicit formulas for the eigenfunction profiles corresponding to these eigenvalues are presented, making it possible to use the theory for hydrocode verification in two and three dimensions.

  8. Occurrence and persistence of future atmospheric stagnation events

    Science.gov (United States)

    Horton, Daniel E.; Skinner, Christopher B.; Singh, Deepti; Diffenbaugh, Noah S.

    2014-08-01

    Poor air quality causes an estimated 2.6-4.4 million premature deaths per year. Hazardous conditions form when meteorological components allow the accumulation of pollutants in the near-surface atmosphere. Global-warming-driven changes to atmospheric circulation and the hydrological cycle are expected to alter the meteorological components that control pollutant build-up and dispersal, but the magnitude, direction, geographic footprint and public health impact of this alteration remain unclear. We used an air stagnation index and an ensemble of bias-corrected climate model simulations to quantify the response of stagnation occurrence and persistence to global warming. Our analysis projects increases in stagnation occurrence that cover 55% of the current global population, with areas of increase affecting ten times more people than areas of decrease. By the late twenty-first century, robust increases of up to 40 days per year are projected throughout the majority of the tropics and subtropics, as well as within isolated mid-latitude regions. Potential impacts over India, Mexico and the western US are particularly acute owing to the intersection of large populations and increases in the persistence of stagnation events, including those of extreme duration. These results indicate that anthropogenic climate change is likely to alter the level of pollutant management required to meet future air quality targets.

  9. Estimation of fluid flow fields and their stagnation points

    DEFF Research Database (Denmark)

    Larsen, Rasmus

    Given a temporal sequence of images of fluids we will use local polynomials to regularise obser-vations of normal flows into smooth flow fields. This technique furthermore allows us to give a qualitative local description of the flow field and to estimate the position of stagnation points...

  10. Stability of stagnation via an expanding accretion shock wave

    Science.gov (United States)

    Velikovich, A. L.; Murakami, M.; Taylor, B. D.; Giuliani, J. L.; Zalesak, S. T.; Iwamoto, Y.

    2016-05-01

    Stagnation of a cold plasma streaming to the center or axis of symmetry via an expanding accretion shock wave is ubiquitous in inertial confinement fusion (ICF) and high-energy-density plasma physics, the examples ranging from plasma flows in x-ray-generating Z pinches [Maron et al., Phys. Rev. Lett. 111, 035001 (2013)] to the experiments in support of the recently suggested concept of impact ignition in ICF [Azechi et al., Phys. Rev. Lett. 102, 235002 (2009); Murakami et al., Nucl. Fusion 54, 054007 (2014)]. Some experimental evidence indicates that stagnation via an expanding shock wave is stable, but its stability has never been studied theoretically. We present such analysis for the stagnation that does not involve a rarefaction wave behind the expanding shock front and is described by the classic ideal-gas Noh solution in spherical and cylindrical geometry. In either case, the stagnated flow has been demonstrated to be stable, initial perturbations exhibiting a power-law, oscillatory or monotonic, decay with time for all the eigenmodes. This conclusion has been supported by our simulations done both on a Cartesian grid and on a curvilinear grid in spherical coordinates. Dispersion equation determining the eigenvalues of the problem and explicit formulas for the eigenfunction profiles corresponding to these eigenvalues are presented, making it possible to use the theory for hydrocode verification in two and three dimensions.

  11. Stagnation point flow and heat transfer for a viscoelastic fluid ...

    Indian Academy of Sciences (India)

    A theoretical study is made in the region near the stagnation point when a lighter incompressible viscoelastic fluids impinges orthogonally on the surface of another quiescent heavier incompressible viscous fluid. Similarity solutions of the momentum balance equations for both fluids are equalized at the interface. It isnoted ...

  12. Analysis of Feeder Bus Network Design and Scheduling Problems

    Directory of Open Access Journals (Sweden)

    Mohammad Hadi Almasi

    2014-01-01

    Full Text Available A growing concern for public transit is its inability to shift passenger’s mode from private to public transport. In order to overcome this problem, a more developed feeder bus network and matched schedules will play important roles. The present paper aims to review some of the studies performed on Feeder Bus Network Design and Scheduling Problem (FNDSP based on three distinctive parts of the FNDSP setup, namely, problem description, problem characteristics, and solution approaches. The problems consist of different subproblems including data preparation, feeder bus network design, route generation, and feeder bus scheduling. Subsequently, descriptive analysis and classification of previous works are presented to highlight the main characteristics and solution methods. Finally, some of the issues and trends for future research are identified. This paper is targeted at dealing with the FNDSP to exhibit strategic and tactical goals and also contributes to the unification of the field which might be a useful complement to the few existing reviews.

  13. Analysis of feeder bus network design and scheduling problems.

    Science.gov (United States)

    Almasi, Mohammad Hadi; Mirzapour Mounes, Sina; Koting, Suhana; Karim, Mohamed Rehan

    2014-01-01

    A growing concern for public transit is its inability to shift passenger's mode from private to public transport. In order to overcome this problem, a more developed feeder bus network and matched schedules will play important roles. The present paper aims to review some of the studies performed on Feeder Bus Network Design and Scheduling Problem (FNDSP) based on three distinctive parts of the FNDSP setup, namely, problem description, problem characteristics, and solution approaches. The problems consist of different subproblems including data preparation, feeder bus network design, route generation, and feeder bus scheduling. Subsequently, descriptive analysis and classification of previous works are presented to highlight the main characteristics and solution methods. Finally, some of the issues and trends for future research are identified. This paper is targeted at dealing with the FNDSP to exhibit strategic and tactical goals and also contributes to the unification of the field which might be a useful complement to the few existing reviews.

  14. Electromagnetic-Thermal Computer Model of Zinc Feeder

    Czech Academy of Sciences Publication Activity Database

    Musil, Ladislav; Praglowska-Gorczynska, Z.

    -, č. 3 (2004), s. 107-110 ISSN 0204-3599 R&D Projects: GA ČR GA102/03/0047 Keywords : zinc feeder * induction heating * levitation Subject RIV: JA - Electronics ; Optoelectronics, Electrical Engineering

  15. Structural integrity investigations of feeder pipe ice plugging procedures

    International Nuclear Information System (INIS)

    Flaman, M.T.; Shah, N.N.

    1985-03-01

    A procedure involving the use of a liquid nitrogen cooled heat exchanger to form internal ice plugs in feeder pipes is routinely used in nuclear generating stations. The use of this procedure has caused concerns with regard to the safety of station maintenance personnel, and in regard to the integrity of the feeder pipes. This report describes the results of laboratory stress and pressure measurements which were performed on a feeder pipe section during ice plugging operations to investigate these concerns. From the results of this study, and from the results of previous studies of material behaviour at low temperatures, it has been determined that the ice plugging procedure can be performed on feeder pipes in a safe and effective manner

  16. SAFIRE - a robotic inspection system for CANDU feeders

    International Nuclear Information System (INIS)

    Buckingham, R.

    2011-01-01

    The condition of primary circuit feeder pipes in CANDU reactors is relevant to the commercial viability and plant life. One known wear mechanism is external fretting between feeder pipes and adjacent services or support structures, particularly within the Upper Feeder Cabinet (UFC). Fretting leads to wall thinning which must not exceed certain agreed limits. Chafe shields have been added to protect the feeder pipes. Regular inspections are required of the chafe shields, feeder pipes and other structures that may cause feeder damage. Historically, the dose received by inspectors conducting this work has been significant. For this reason Ontario Power Generation has invested in a remotely operated robot system to conduct visual inspections within the UFC. This system, called SAFIRE for 'Snake-Arm Feeder Inspection Robot Equipment' has been deployed at Pickering during 2010 and 2011 and has been used to inspect areas that are extremely difficult to inspect with existing manual techniques. The 2011 scope of work included inspection of a total of 660 feeder pipes in three UFC quadrants, in two reactors. The full scope was completed over a one-month period in Autumn 2011 in which SAFIRE was used during 23, twelve hour shifts. This included two periods each of 72 hours of continuous operation using multiple teams of operators. SAFIRE is remote controlled delivery system for multiple cameras to record still images and video. The main system elements include a snake-arm robot mounted on a mobile vehicle. It can be controlled from up to 500m away using a fibre/copper connection. The snake-arm is 2.2m long, 25mm wide and has 18 degrees of freedom. It is designed to snake between the rows of feeder pipes to inspect feeder/hanger interfaces, both above and below the feeder cabinet catwalks. Future upgrades offer the potential to add additional tools to increase functionality. This paper describes the SAFIRE development process from inception to operational experience gained

  17. Urban Bird Feeders Dominated by a Few Species and Individuals

    Directory of Open Access Journals (Sweden)

    Josie A. Galbraith

    2017-08-01

    Full Text Available The practice of garden bird feeding is a global phenomenon, involving millions of people and vast quantities of food annually. Many people engage in the practice of feeding assuming that birds gain some benefit from the food they provide, yet recent studies have revealed the potential for detrimental impacts as well. However, there is still a paucity of information on the impacts of feeding, including the ubiquity of these impacts among and within feeder-visiting species. Consistency in feeder use among birds is likely an important determinant of this. Individual birds and species that make frequent use of feeders are more likely to experience both the benefits and detrimental impacts of supplementary food. We investigated patterns of feeder use by garden birds visiting experimental feeding stations in Auckland, New Zealand, with the specific aim of determining whether use of supplementary food was consistent or variable among individuals and species. We used camera traps as well as Radio Frequency Identification (RFID technology to examine intra- and interspecific feeder visitation patterns and to discern species associations. Eleven bird species were detected using feeding stations, however, two introduced species (house sparrow Passer domesticus and spotted dove Streptopelia chinensis dominated visitation events. These species were present at feeders most frequently, with the largest conspecific group sizes. Significant associations were detected among a number of species, suggesting interspecific interactions are important in determining feeder use. We also found within-species differences in feeder use for all focal species, with individual variation greatest in house sparrows. Furthermore, season had an important influence on most visitation parameters. The observed individual and species-specific differences in supplementary food resource use imply that the impacts of garden bird feeding are not universal. Crucially, particularly given

  18. Fitness-for-service guidelines for CANDU feeders

    International Nuclear Information System (INIS)

    Scarth, D.; Thompson, I.

    2006-01-01

    Condition assessments of fuel channel feeder piping in CANDU nuclear power plants are under the jurisdiction of the CSA Standard CAN/CSA-N285.4. When the predicted end-of-evaluation-period wall loss exceeds the acceptance criteria, fitness-for-service assessment is required to demonstrate feeder integrity. The occurrence of degradation mechanisms in CANDU feeders has led to the need for a Fitness-for-Service Guidelines document that contains standardized evaluation methods for fitness-for-service assessments. The main objectives of the Fitness-for-Service Guidelines are to provide reasonable assurance that feeder structural integrity is maintained, and to provide reasonable assurance that consequential leakage from flaws is acceptable. Acceptance criteria for degraded feeders are based on the concept of safety-related Performance Criteria that require feeder structural integrity be maintained during the evaluation period, that operational leak rate is monitored and does not exceed the allowable limit, and that consequential leakage during upset or abnormal events is acceptable. (author)

  19. The Break

    DEFF Research Database (Denmark)

    Strand, Anete Mikkala Camille

    2018-01-01

    The chapter elaborates on how to deal with one of the major challenges facing organizations worldwide; Stress. The Break enacts a quantum approach to meet the challenges by proposing a combination of three different quantum storytelling technologies; protreptic mentoring, walking and material sto...

  20. Supersymmetry breaking

    Indian Academy of Sciences (India)

    symmetry asks for the existence of a bosonic massless partner, which generically correspond to a non-compact flat direction. ... Hidden Sector nonren.int. Ti, 〈Fi〉 = 0. Let us define the strength of supersymmetry breaking by F2 = ∑ ... partners, not protected by the GIM mechanism. Solutions for FCNC problem: (i) Flavour ...

  1. Electroweak breaking and supersymmetry breaking

    Indian Academy of Sciences (India)

    We discuss the clash between the absence of fine tuning in the Higgs potential and a sufficient suppression of flavour changing neutral current transitions in supersymmetric extensions of the standard model. It is pointed out that horizontal U ( 1 ) symmetry combined with the D -term supersymmetry breaking provides a ...

  2. Estimation of Centers and Stagnation points in optical flow fields

    DEFF Research Database (Denmark)

    Larsen, Rasmus

    1997-01-01

    distribution of spatio-temporal energy, which is sampled using a set of spatio-temporal quadrature filters. These observations of normal flows are then integrated into smooth flow fields by locally approximating first order polynomials in the spatial coordinates to the flow vectors. This technique furthermore......In a topological sense fluid flows are characterised by their stagnation points. Given a temporal sequence of images of fluids we will consider the application of local polynomials to the estimation of smooth fluid flow fields. The normal flow at intensity contours is estimated from the local...... allows us to give a qualitative local description of the flow field and to estimate the position of stagnation points (e.g. nodes, saddles, and centers). We will apply the algorithm to two data sets. The first sequence consists of infrared images from the meteorological satellite Meteosat. Here...

  3. Investigation of plasma instabilities in the stagnated Z pinch

    Science.gov (United States)

    Ivanov, V. V.; Chittenden, J. P.; Mancini, R. C.; Papp, D.; Niasse, N.; Altemara, S. D.; Anderson, A. A.

    2012-10-01

    High-resolution laser probing diagnostics at a wavelength of 266 nm allow observation of the internal structure and instabilities in dense stagnated Z pinches, typically hidden by trailing material. The internal structure of the 1-MA Z pinch includes strong kink and sausage instabilities, loops, flares, and disruptions. Mid- and small-scale density perturbations develop in the precursor and main pinch. The three-dimensional shape and dynamics of the wire-array Z pinch are predetermined by the initial configuration of the wire array. Cylindrical, linear, and star wire-array Z pinches present different sets of instabilities seeded to the pinch at the implosion stage. Prolonged implosion of trailing mass can enhance x-ray production in wire arrays. Fast plasma motion with a velocity >100 km/s was observed in the Z pinch at stagnation with two-frame shadowgraphy. Development of instabilities in wire arrays is in agreement with three-dimensional magnetohydrodynamic simulations.

  4. Xeroradiography: Stagnated after a Promising Beginning? A Historical Review

    OpenAIRE

    Udoye, Christopher I.; Jafarzadeh, Hamid

    2010-01-01

    Various methods have been introduced for obtaining radiographs. Xeroradiography which is a method of imaging uses the xeroradiographic copying process to record images produced by diagnostic x-rays. It differs from halide film technique in that it involves neither wet chemical processing nor the use of dark room. Literature on this subject is scarce. After an initial promising beginning, this imaging method, once thought to hold the key to endodontic imaging, got stagnated. A revisit of this ...

  5. Breaking Symmetries

    Directory of Open Access Journals (Sweden)

    Kirstin Peters

    2010-11-01

    Full Text Available A well-known result by Palamidessi tells us that πmix (the π-calculus with mixed choice is more expressive than πsep (its subset with only separate choice. The proof of this result argues with their different expressive power concerning leader election in symmetric networks. Later on, Gorla offered an arguably simpler proof that, instead of leader election in symmetric networks, employed the reducibility of incestual processes (mixed choices that include both enabled senders and receivers for the same channel when running two copies in parallel. In both proofs, the role of breaking (initial symmetries is more or less apparent. In this paper, we shed more light on this role by re-proving the above result - based on a proper formalization of what it means to break symmetries without referring to another layer of the distinguishing problem domain of leader election. Both Palamidessi and Gorla rephrased their results by stating that there is no uniform and reasonable encoding from πmix into πsep. We indicate how the respective proofs can be adapted and exhibit the consequences of varying notions of uniformity and reasonableness. In each case, the ability to break initial symmetries turns out to be essential.

  6. Investigation of Hypersonic Laminar Heating Augmentation in the Stagnation Region

    Science.gov (United States)

    Marineau, Eric C.; Lewis, Daniel R.; Smith, Michael S.; Lafferty, John F.; White, Molly E.; Amar, Adam J.

    2012-01-01

    Laminar stagnation region heating augmentation is investigated in the AEDC Tunnel 9 at Mach 10 by performing high frequency surface pressure and heat transfer measurements on the Orion CEV capsule at zero degree angle-of-attack for unit Reynolds numbers between 0.5 and 15 million per foot. Heating augmentation increases with Reynolds number, but is also model size dependent as it is absent on a 1.25-inch diameter model at Reynolds numbers where it reaches up to 15% on a 7-inch model. Heat transfer space-time correlations on the 7-inch model show that disturbances convect at the boundary layer edge velocity and that the streamwise integral scale increases with distance. Therefore, vorticity amplification due to stretching and piling-up in the stagnation region appears to be responsible for the stagnation point heating augmentation on the larger model. This assumption is reinforced by the f(exp -11/3) dependence of the surface pressure spectrum compared to the f(exp -1) dependence in the free stream. Vorticity amplification does not occur on the 1.25- inch model because the disturbances are too large. Improved free stream fluctuation measurements will be required to determine if significant vorticity is present upstream or mostly generated behind the bow shock.

  7. Granular Material Scoop and Near-Vertical Lifting Feeder/Conveyor

    Science.gov (United States)

    Walton, Otis (Inventor); Vollmer, Hubert J. (Inventor)

    2017-01-01

    An integrated granular-material scoop and near-vertical lifting feeder/conveyor includes special connections and skirts between a bullnose rotating scoop and an open-helical screw that provides the rotations and material lift and evacuation. A conical working-face of the bullnose rotating scoop has symmetrically distributed graters and vents to break loose and force-in granular material from natural deposits and cargo holds. The bullnose rotating scoop and the open-helical screw its attached to move the material into a continuous layer on the inside surface of an outer stationary sheathing. A motor drive attached to the open-helical screw above at the delivery end provides the lifting force necessary.

  8. Technologies to Increase PV Hosting Capacity in Distribution Feeders: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Ding, Fei; Mather, Barry; Gotseff, Peter

    2016-08-01

    This paper studies the distributed photovoltaic (PV) hosting capacity in distribution feeders by using the stochastic analysis approach. Multiple scenario simulations are conducted to analyze several factors that affect PV hosting capacity, including the existence of voltage regulator, PV location, the power factor of PV inverter and Volt/VAR control. Based on the conclusions obtained from simulation results, three approaches are then proposed to increase distributed PV hosting capacity, which can be formulated as the optimization problem to obtain the optimal solution. All technologies investigated in this paper utilize only existing assets in the feeder and therefore are implementable for a low cost. Additionally, the tool developed for these studies is described.

  9. Laying method for superconducting feeder cable along railway line

    Science.gov (United States)

    Tomita, Masaru; Akasaka, Tomoyuki; Fukumoto, Yusuke; Ishihara, Atsushi; Suzuki, Kenji; Kobayashi, Yusuke

    2018-01-01

    The superconducting feeder cable shrinks in cooling process from the room temperature to the temperature of liquid nitrogen. When a long superconducting feeder cable is constructed in a railway line, it is needed to consider countermeasures against the cable shrink due to cooling force. We report on a suitable method of laying the cable in 300-m class on the test track. We also report that the method is suitable for this cable because no buckling and rupture points were observed in the X-ray radiograph taken over the whole length of the cable after its installation.

  10. Stagnation and interpenetration of laser-created colliding plasmas

    Energy Technology Data Exchange (ETDEWEB)

    Pollaine, S.M.; Albritton, J.R.; Kauffman, R.; Keane, C.J. (Lawrence Livermore National Lab., CA (USA)); Berger, R.L.; Bosch, R.; Delameter, N.D.; Failor, B.H. (KMS Fusion, Inc., Ann Arbor, MI (USA))

    1990-11-05

    A KMS laser experiment collides Aluminum (A1) and Magnesium (Mg) plasmas. The measurements include electron density, time and space resolved Ly-alpha and He-alpha lines of Al and Mg, and x-ray images. These measurements were analyzed with a hydrodynamic code, LASNEX, and a special two-fluid code OFIS. The results strongly suggest that at early times, the Al interpenetrates the counterstreaming Mg and deposits in the dense Mg region. At late times, the Al plasma stagnates against the Mg plasma.

  11. Stagnation Region Heat Transfer Augmentation at Very High Turbulence Levels

    Energy Technology Data Exchange (ETDEWEB)

    Ames, Forrest [University of North Dakota; Kingery, Joseph E. [University of North Dakota

    2015-06-17

    A database for stagnation region heat transfer has been extended to include heat transfer measurements acquired downstream from a new high intensity turbulence generator. This work was motivated by gas turbine industry heat transfer designers who deal with heat transfer environments with increasing Reynolds numbers and very high turbulence levels. The new mock aero-combustor turbulence generator produces turbulence levels which average 17.4%, which is 37% higher than the older turbulence generator. The increased level of turbulence is caused by the reduced contraction ratio from the liner to the exit. Heat transfer measurements were acquired on two large cylindrical leading edge test surfaces having a four to one range in leading edge diameter (40.64 cm and 10.16 cm). Gandvarapu and Ames [1] previously acquired heat transfer measurements for six turbulence conditions including three grid conditions, two lower turbulence aero-combustor conditions, and a low turbulence condition. The data are documented and tabulated for an eight to one range in Reynolds numbers for each test surface with Reynolds numbers ranging from 62,500 to 500,000 for the large leading edge and 15,625 to 125,000 for the smaller leading edge. The data show augmentation levels of up to 136% in the stagnation region for the large leading edge. This heat transfer rate is an increase over the previous aero-combustor turbulence generator which had augmentation levels up to 110%. Note, the rate of increase in heat transfer augmentation decreases for the large cylindrical leading edge inferring only a limited level of turbulence intensification in the stagnation region. The smaller cylindrical leading edge shows more consistency with earlier stagnation region heat transfer results correlated on the TRL (Turbulence, Reynolds number, Length scale) parameter. The downstream regions of both test surfaces continue to accelerate the flow but at a much lower rate than the leading edge. Bypass transition occurs

  12. Pressure and temperature development in solar heating system during stagnation

    DEFF Research Database (Denmark)

    Dragsted, Janne; Furbo, Simon; Chen, Ziqian

    2010-01-01

    of the pipes of the solar collector loop. During the investigation the pre-pressure of the expansion vessel and system filling pressure was changed. The investigations showed that a large pressurised expansion vessel will protect the collector loop from critically high temperatures as long as the solar......This paper presents an investigation of stagnation in solar collectors and the effects it will have on the collector loop. At a laboratory test stand at the Technical University of Denmark, a pressurized solar collector loop was designed to test different numbers of collectors and different designs...

  13. Microplastic in a macro filter feeder: humpback whale Megaptera novaeangliae

    NARCIS (Netherlands)

    Besseling, E.; Foekema, E.M.; Franeker, van J.A.; Leopold, M.F.; Bravo Rebolledo, E.; Kuehn, S.; Mielke, L.; Heberle-Bors, E.; Ijzer, J.; Kamminga, P.; Koelmans, A.A.

    2015-01-01

    Marine filter feeders are exposed to microplastic because of their selection of small particles as food source. Baleen whales feed by filtering small particles from large water volumes. Macroplastic was found in baleen whales before. This study is the first to show the presence of microplastic in

  14. Microplastic in a macro filter feeder: Humpback whale Megaptera novaeangliae.

    NARCIS (Netherlands)

    E., Besseling,; E.M., Foekema,; J.A. van, Franeker; Leopold, Mardik F; Kuhn, S.; Bravo Rebolledo, E.L.; Hese, E.; Mielke, L.; IJzer, J.|info:eu-repo/dai/nl/304839663; Kamminga, P.; Koelmans, A.A.

    2015-01-01

    Marine filter feeders are exposed to microplastic because of their selection of small particles as food source. Baleen whales feed by filtering small particles from large water volumes. Macroplastic was found in baleen whales before. This study is the first to show the presence of microplastic in

  15. A methodology for identification and ranking of hazardous feeder ...

    African Journals Online (AJOL)

    A methodology for identification and ranking of hazardous feeder road sections in Ghana. KK Adarkwa, M Salifu. Abstract. No Abstract. Journal of the Ghana Institution of Engineers Vol. 2 (1) 2004: pp. 9-18. Full Text: EMAIL FULL TEXT EMAIL FULL TEXT · DOWNLOAD FULL TEXT DOWNLOAD FULL TEXT · AJOL African ...

  16. 46 CFR 58.25-65 - Feeder circuits.

    Science.gov (United States)

    2010-10-01

    ... of the electric steering-gear motor or power unit; and (2) 100% of the normal current of one steering-gear control system including all associated motors. ... AND RELATED SYSTEMS Steering Gear § 58.25-65 Feeder circuits. (a) Each vessel with one or more...

  17. Faecal nitrogen of browser and mixed feeder game species during ...

    African Journals Online (AJOL)

    A practical measure of assessing periods of potential nutritional stress of game species is needed in the management of these species in the Acacia karroo Riparian Thicket of the central Free State. The objectives of the study were to determine Nf concentration of four game species (browsers and mixed feeders) during ...

  18. A Decentralized Storage Strategy for Residential Feeders with Photovoltaics

    DEFF Research Database (Denmark)

    Marra, Francesco; Yang, Guangya; Træholt, Chresten

    2014-01-01

    This paper proposes a decentralized voltage support strategy for LV residential feeders with high roof-top PV capacity installed. The proposed strategy is capable of increasing the local consumption at private households with PV during high generation periods, by the use of locally controlled dom...

  19. Optimisation of Trap Design for Vibratory Bowl Feeders

    DEFF Research Database (Denmark)

    Mathiesen, Simon; Sørensen, Lars Carøe; Kraft, Dirk

    2018-01-01

    Vibratory bowl feeders (VBFs) are a widely used option for industrial part feeding, but their design is still largely manual. A subtask of VBF design is determining an optimal parameter set for the passive devices, called traps, which the VBF uses to ensure correct part orientation. This paper...

  20. Development of a Feeder for Uninterrupted Centrifugation Studies

    Science.gov (United States)

    Mulenburg, Gerald M.; Vasques, Marilyn F.; Gundo, Daniel P.; Griffith, Jon B.; Wade, Charles E. (Technical Monitor)

    1994-01-01

    A specialized paste diet feeder was developed in support of a hypergravity (2G) centrifuge study. The centrifuge study was to be compared to a previously flown Russian Cosmos spaceflight so experimental parameters of the 14 day spaceflight had to be duplicated. In order to duplicate at hyper G an experiment that took place in weightlessness, all other conditions must be as identical as possible. Stopping the centrifuge to provide maintenance for the animals causes unacceptable changes in experimental research results. Thus the experimental protocol required the delivery of a designated amount of paste diet at regular intervals for a two week period without stopping the centrifuge. A centrifuge and a stationary control cage, each containing 10 laboratory rats, were fitted with feeders that were calibrated to provide 140 plus or minus 2g of paste diet every 6 hours. This paper describes development of the feeder design and results of its operation over the two week experiment. The design philosophy and details of the feeder system are provided with recommendations for future such devices.

  1. Standard Test Method for Calculation of Stagnation Enthalpy from Heat Transfer Theory and Experimental Measurements of Stagnation-Point Heat Transfer and Pressure

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    2005-01-01

    1.1 This test method covers the calculation from heat transfer theory of the stagnation enthalpy from experimental measurements of the stagnation-point heat transfer and stagnation pressure. 1.2 Advantages 1.2.1 A value of stagnation enthalpy can be obtained at the location in the stream where the model is tested. This value gives a consistent set of data, along with heat transfer and stagnation pressure, for ablation computations. 1.2.2 This computation of stagnation enthalpy does not require the measurement of any arc heater parameters. 1.3 Limitations and ConsiderationsThere are many factors that may contribute to an error using this type of approach to calculate stagnation enthalpy, including: 1.3.1 TurbulenceThe turbulence generated by adding energy to the stream may cause deviation from the laminar equilibrium heat transfer theory. 1.3.2 Equilibrium, Nonequilibrium, or Frozen State of GasThe reaction rates and expansions may be such that the gas is far from thermodynamic equilibrium. 1.3.3 Noncat...

  2. Nested separatrices in simple shear flows: the effect of localized disturbances on stagnation lines

    OpenAIRE

    Wilson, M.C.T.; Gaskell, P.H.; Savage, M.D.

    2005-01-01

    The effects of localized two-dimensional disturbances on the structure of shear flows featuring a stagnation line are investigated. A simple superposition of a planar Couette flow and Moffatt's [J. Fluid Mech. 18, 1--18 (1964)] streamfunction for the decay of a disturbance between infinite stationary parallel plates shows that in general the stagnation line is replaced by a chain of alternating elliptic and hyperbolic stagnation points with a separation equal to 2.78 times the half-gap betwee...

  3. Best estimate analysis of GDH break in RBMK-1500

    International Nuclear Information System (INIS)

    Vileiniskis, V.; Kaliatka, A.; Uspuras, E.

    2004-01-01

    The RBMK-1500 is a multichannel boiling water and graphite moderated nuclear reactor. Two identical cooling loops compose the main circulation circuit, which consists of 1661 parallel fuel channels (FC) and numerous components, such as collectors, headers, pumps, etc. There are 20 group distribution headers (GDH) in the each cooling loop. Guillotine or partial break of one GDH, which in turn feeds 38-43 FC, leads to the sharp coolant flow rate decrease in the FC connected to the affected GDH. In the case of partial GDH break the short-term flow stagnation in the group of fuel channels connected to ruptured GDH can occur. Thus, any GDH break is accompanied by fuel cladding and fuel channel temperature increase. This paper presents best estimate analysis of possible GDH breaks in Ignalina Nuclear Power Plant RBMK-1500 reactor: Guillotine break upstream check valve, Guillotine break downstream check valve, Partial break. Best estimate code RELAP5/MOD3.2 was used for deterministic analysis. According to the international practice if a best estimate code is used for the analysis, the uncertainty and sensitivity analysis should be performed. Sensitivity and uncertainty analysis was performed employing System for Uncertainty and Sensitivity Analysis (SUSA) developed at GRS (Germany). Results of the analysis shows that acceptance criterion for fuel cladding temperature is violated only short time period in the case of GDH guillotine break, in the case of partial GDH break the reactor core will be reliably cooled.(author)

  4. Novel Methods to Determine Feeder Locational PV Hosting Capacity and PV Impact Signatures

    Energy Technology Data Exchange (ETDEWEB)

    Reno, Matthew J. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Coogan, Kyle [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Seuss, John [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Broderick, Robert Joseph [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2017-05-01

    Often PV hosting capacity analysis is performed for a limited number of distribution feeders. For medium - voltage distribution feeders, previous results generally analyze less than 20 feeders, and then the results are extrapolated out to similar types of feeders. Previous hosting capacity research has often focused on determining a single value for the hosting capacity for the entire feeder, whereas this research expands previous hosting capacity work to investigate all the regions of the feeder that may allow many different hosting capacity values wit h an idea called locational hosting capacity (LHC)to determine the largest PV size that can be interconnected at different locations (buses) on the study feeders. This report discusses novel methods for analyzing PV interconnections with advanced simulati on methods. The focus is feeder and location - specific impacts of PV that determine the locational PV hosting capacity. Feeder PV impact signature are used to more precisely determine the local maximum hosting capacity of individual areas of the feeder. T he feeder signature provides improved interconnection screening with certain zones that show the risk of impact to the distribution feeder from PV interconnections.

  5. Large round bale feeder design affects hay utilization and beef cow behavior.

    Science.gov (United States)

    Buskirk, D D; Zanella, A J; Harrigan, T M; Van Lente, J L; Gnagey, L M; Kaercher, M J

    2003-01-01

    One hundred sixty beef cows (631 +/- 78 kg) were used to evaluate the quantity of hay loss and feeding behaviors from different round bale feeders. Twenty cows were allotted by weight and body condition score to one of eight pens with four feeder designs: cone, ring, trailer, or cradle. All feeder types provided approximately 37 cm of linear feeder space per animal. Alfalfa and orchardgrass round bales were weighed and sampled before feeding. Hay that fell onto the concrete surrounding the feeder was considered waste and was collected and sampled daily. At the end of a 7-d period, each feeder type was assigned to a different pen for a second 7-d period. On four consecutive days in each period, animal behavior was recorded using a time-lapse video system. Data were collected from 5-min observational intervals from the video tapes every 0.5 h each day. Feeder access, occupancy rate, and occurrence of agonistic interactions were recorded. Dry matter hay waste was 3.5, 6.1, 11.4, and 14.6% for the cone, ring, trailer, and cradle feeders, respectively. Calculated dry matter intake of hay ranged from 1.8 to 2.0% of body weight and was not different among feeder type (P < 0.05). Percentage of organic matter, neutral detergent fiber, acid detergent fiber, and crude protein were all lower and acid detergent lignin was higher in the recovered waste compared to the hay fed (P < 0.05). Cows feeding from the cradle feeder had nearly three times the agonistic interactions and four times the frequency of entrances compared to cows feeding from the other feeder types (P < 0.05). Feed losses were positively correlated with agonistic interactions, frequency of regular and irregular entrances, and feeder occupancy rate (P < 0.05). Agonistic interactions by cows and frequency of feeder entrances differed among feeders and were correlated to feeder design induced feed losses.

  6. Recirculation, stagnation and ventilation: The 2014 legionella episode

    Science.gov (United States)

    Russo, Ana; Soares, Pedro M. M.; Gouveia, Célia M.; Cardoso, Rita M.; Trigo, Ricardo M.

    2017-04-01

    Legionella transmission through the atmosphere is unusual, but not unprecedented. A scientific paper published in 2006 reports a surge in Pas-de-Calais, France, in which 86 people have been infected by bacteria released by a cooling tower more than 6 km away [3]. Similarly, in Norway, in 2005, there was another case where contamination spread beyond 10 km, although more concentrated within a radius of 1 km from an industrial unit [2]. An unprecedented large Legionella outbreak occurred in November 2014 nearby Lisbon, Portugal. As of 7 November 2014, 375 individuals become hill and 12 died infected by the Legionella pneumophila bacteria, contracted by inhalation of steam droplets of contaminated water (aerosols). These droplets are so small that can carry the bacteria directly to the lungs, depositing it in the alveoli. One way of studying the propagation of legionella episodes is through the use of aerosol dispersion models. However, such approaches often require detailed 3D high resolution wind data over the region, which isn't often available for long periods. The likely impact of wind on legionella transmission can also be understood based on the analysis of special types of flow conditions such as stagnation, recirculation and ventilation [1, 4]. The Allwine and Whiteman (AW) approach constitutes a straightforward method to assess the assimilative and dispersal capacities of different airsheds [1,4], as it only requires hourly wind components. Thus, it has the advantage of not needing surface and upper air meteorological observations and a previous knowledge of the atmospheric transport and dispersion conditions. The objective of this study is to analyze if the legionella outbreak event which took place in November 2014 had extreme potential recirculation and/or stagnation characteristics. In order to accomplish the proposed objective, the AW approach was applied for a hindcast time-series covering the affected area (1989-2007) and then for an independent

  7. Feeding Against Gravity with Spot Feeders in High Silicon Ductile Iron

    DEFF Research Database (Denmark)

    Vedel-Smith, Nikolaj Kjelgaard; Tiedje, Niels Skat

    2014-01-01

    A test pattern, with three different moduli castings was developed to investigate methods to optimise feeding of high silicon ductile cast irons. Different feeder types, modulus, and locations were investigated using both an insulating and an exothermal sleeve material. Porosities were analysed...... by the feeders made with the insulating sleeve material was not sufficient to significantly improve feeding...... and classified using X-ray imaging and ultrasound analysis. The effect of the different feeder configurations were classified in reference to defect location, sleeve material, and feeder type, modulus, and location. The analysis showed that exothermal feeder sleeves with the right configurations can feed up...

  8. Rise, stagnation, and rise of Danish women's life expectancy

    DEFF Research Database (Denmark)

    Lindahl-Jacobsen, Rune; Rau, Roland; Jeune, Bernard

    2016-01-01

    Health conditions change from year to year, with a general tendency in many countries for improvement. These conditions also change from one birth cohort to another: some generations suffer more adverse events in childhood, smoke more heavily, eat poorer diets, etc., than generations born earlier...... favor forecasts that hinge on cohort differences. We use a combination of age decomposition and exchange of survival probabilities between countries to study the remarkable recent history of female life expectancy in Denmark, a saga of rising, stagnating, and now again rising lifespans. The gap between...... female life expectancy in Denmark vs. Sweden grew to 3.5 y in the period 1975-2000. When we assumed that Danish women born 1915-1945 had the same survival probabilities as Swedish women, the gap remained small and roughly constant. Hence, the lower Danish life expectancy is caused by these cohorts...

  9. Demographic stagnation and decline in Spain: A cause for concern?

    Directory of Open Access Journals (Sweden)

    Serrano-Martínez José-María

    2018-03-01

    Full Text Available For years, the Spanish population has been rapidly ageing, showing signs of atony and stagnation. Between 1996 and 2007, in a phase of economic growth, the entry of foreign immigrants drove a global increase in population. But after the economic recession migratory flows show negative net balances. Our objective is to explain and confirm the demographic regression suffered by Spain. We are also interested in showing how the recent and intense immigration process has failed to generate significant changes in natural demographic characteristics and trends. National censuses, published by the National Institute of Statistics (INE, are our main source of demographic data. The analysis of the most recent relevant scientific literature has allowed us to compare opinions and discuss results. The data confirm an uncertain and worrying future for the Spanish population.

  10. Feeder Service- Logistic Support to the Port of Rijeka

    OpenAIRE

    Bojan Hlača; Adrijana Orlić Babić

    2006-01-01

    The shipping trade has also got caught up in the worldwideglobalization trend. Today there are some ten strong ship operatorsin the world (so called mega shipowners) who are workingeither on their own or are mutually connected to cover aspecific market. In an effort to meet the requirements of the endusers, the shipping companies tend to organize strong feederservices. Feeder services can also be initiated by terminal operatoror port authority which is most often reflected in the subventionof...

  11. A novel coal feeder for production of low sulfur fuel

    Energy Technology Data Exchange (ETDEWEB)

    Khang, S.J.; Lin, L.; Keener, T.C.; Yeh, P.

    1991-01-01

    A dual-screw feeder was designed for desulfurization of coal. This reactor contains two screw tubes, the inner tube acting as a coal pyrolizer and the outer tube acting as a desulfurizer with hot calcined lime pellets or other renewable sorbent pellets. The objectives of this project is to study the feasibility of an advanced concept of desulfurization and possibly some denitrification in this coal feeder. In this year, two basic studies have been performed: (1) the desulfurization and (2) the denitrification due to mild pyrolysis. Specifically, the following tasks have been performed: (1) Setting up the Dual-Screw reactor, (2) Determination of the pyrolysis product and the sulfur distribution in char, tar and gas based on experimental data, (3) Study of the devolatilization, the desulfurization kinetics and the denitrification kinetics and obtaining the basic kinetic parameters, (4) Study of the sulfur removal efficiency of lime pellets fed into the outer tube of the dual-feeder reactor, (5) Study of the effect of the coal particle size on pyrolysis and desulfurization, (6) Study of the coal pyrolysis and desulfurization using a TGA(Thermal Gravimetric Analyzer).

  12. Digital optical feeder links system for broadband geostationary satellite

    Science.gov (United States)

    Poulenard, Sylvain; Mège, Alexandre; Fuchs, Christian; Perlot, Nicolas; Riedi, Jerome; Perdigues, Josep

    2017-02-01

    An optical link based on a multiplex of wavelengths at 1.55μm is foreseen to be a valuable solution for the feeder link of the next generation of high-throughput geostationary satellite. The main satellite operator specifications for such link are an availability of 99.9% over the year, a capacity around 500Gbit/s and to be bent-pipe. Optical ground station networks connected to Terabit/s terrestrial fibers are proposed. The availability of the optical feeder link is simulated over 5 years based on a state-of-the-art cloud mask data bank and an atmospheric turbulence strength model. Yearly and seasonal optical feeder link availabilities are derived and discussed. On-ground and on-board terminals are designed to be compliant with 10Gbit/s per optical channel data rate taking into account adaptive optic systems to mitigate the impact of atmospheric turbulences on single-mode optical fiber receivers. The forward and return transmission chains, concept and implementation, are described. These are based on a digital transparent on-off keying optical link with digitalization of the DVB-S2 and DVB-RCS signals prior to the transmission, and a forward error correcting code. In addition, the satellite architecture is described taking into account optical and radiofrequency payloads as well as their interfaces.

  13. Round-bale feeder design affects hay waste and economics during horse feeding.

    Science.gov (United States)

    Martinson, K; Wilson, J; Cleary, K; Lazarus, W; Thomas, W; Hathaway, M

    2012-03-01

    Many horse owners find round bales convenient, less labor intensive, and more affordable than other hay types, but report an inability to control horse BW gain and excessive hay waste. The objectives were to compare hay waste, hay intake, and payback of 9 round-bale feeders and a no-feeder control when used during horse feeding. Nine round-bale feeders were tested: Cinch Net, Cone, Covered Cradle, Hayhut, Hay Sleigh, Ring, Tombstone, Tombstone Saver, and Waste Less. Each feeder design was placed on the ground in a dirt paddock. Five groups of 5 horses were fed in rotation for a 4-d period with each feeder. Every fourth day, groups were rotated among paddocks and a new round bale was placed in each feeder. In the 5 paddocks used, 5 feeders were installed for d 1 through 20, and the remaining 4 feeders and no-feeder control were installed for d 21 through 40. Groups of horses were sequentially assigned to feeders using two 5 × 5 Latin squares, the first for d 1 through 20, the second for d 21 through 40. Horse groups of similar age, BW, breed, and sex were formed from 25 Quarter Horse and Thoroughbred geldings and open mares (means: 11 yr; 541 kg of BW). Hay on the ground surrounding the feeder was collected daily, dried, and weighed. The total amount of hay removed around each feeder for a 4-d period was considered waste. Dry matter intake was estimated as the difference between hay disappearance and waste. Number of months for the reduction in waste to repay feeder cost (payback) were calculated using hay valued at $110/t, and improved feeder efficiency over the control. Feeder design did not affect hay intake (P > 0.05); all feeders resulted in an estimated hay intake of 2.0 to 2.4% BW; the no-feeder control resulted in a reduced intake of 1.3% BW (P = 0.001). Mean percentage of hay waste differed among feeders (P payback (P payback, but not estimated hay intake or BW change during horse feeding.

  14. Clustering method and representative feeder selection for the California solar initiative

    Energy Technology Data Exchange (ETDEWEB)

    Broderick, Robert Joseph; Williams, Joseph R.; Munoz-Ramos, Karina

    2014-02-01

    The screening process for DG interconnection procedures needs to be improved in order to increase the PV deployment level on the distribution grid. A significant improvement in the current screening process could be achieved by finding a method to classify the feeders in a utility service territory and determine the sensitivity of particular groups of distribution feeders to the impacts of high PV deployment levels. This report describes the utility distribution feeder characteristics in California for a large dataset of 8,163 feeders and summarizes the California feeder population including the range of characteristics identified and most important to hosting capacity. The report describes the set of feeders that are identified for modeling and analysis as well as feeders identified for the control group. The report presents a method for separating a utilitys distribution feeders into unique clusters using the k-means clustering algorithm. An approach for determining the feeder variables of interest for use in a clustering algorithm is also described. The report presents an approach for choosing the feeder variables to be utilized in the clustering process and a method is identified for determining the optimal number of representative clusters.

  15. Stagnating Jatropha Biofuel Development in Southwest China: An Institutional Approach

    Directory of Open Access Journals (Sweden)

    Jia Li

    2014-05-01

    Full Text Available Biodiesel from jatropha has been considered as a promising alternative to fossil fuels for some time. Consequently, China started promoting jatropha as one of the options to meet its ever-increasing energy consumption, and the Chinese biodiesel industry also gained interest. However, the excitement of the biofuel industry in jatropha faded after it did not bring about the expected results. This article investigates the stagnation in jatropha development and production for biodiesel in China, using two detailed case studies of jatropha biofuel production in southeast China. It is found that the underdeveloped biodiesel policy and regulation, such as a rather late formulation of standards for biodiesel (especially the B5 and the absence of mandatory targets, is an important reason for hampering jatropha development. Besides that, lack of financial support undermined sustained jatropha planting at the farm level and lack of sustained commitment from state-owned enterprises or private companies over a long time span further contributed to jatropha project’s failure. Better implementation of the rule of law, mandatory blending requirements, hazard insurance, as well as continuous financial support, might improve the continuation of jatropha plantation schemes.

  16. Wage Dispersion, Public Sector Wages and the Stagnating Danish Gender Wage Gap

    DEFF Research Database (Denmark)

    Gupta, Nabanita Datta; Oaxaca, Ronald L.; Smith, Nina

    1998-01-01

    The gender wage gap in Denmark has virtually stagnated since the early 70s. This study examines whether this stagnation is mainly due to a changing wage dispersion or to changing prices on observed and unobserved skills. Since about half the female labour force is employed in the public sector....... These techniques are applied to a sample of Danish wage earners in the period 1983-94. The decomposition results suggest different explanations behind the stagnation of the gender wage gap in the public and private sectors. The development in average public sector wages is calculated assuming observed...

  17. S08: investigation and repair of a cracked feeder at Point Lepreau GS

    International Nuclear Information System (INIS)

    A Celovsky, A.; Wright, M.D.; Gendron, T.S.

    1997-01-01

    Early in 1997 investigation of a low level leak in the Point Lepreau GS (PLGS) PHTS revealed that an outlet feeder, S08, was leaking. Ultrasonic inspection, and subsequent failure analysis, revealed that the leak was a consequence of a crack. Given the unusual nature of this event, and current concerns over feeder thinning, a detailed and careful removal and examination procedure was developed. The S08 outlet feeder was removed and shipped to Chalk River Laboratories for examination. The examination confirmed that the failure was a through-wall crack, most likely the consequence of stress corrosion cracking. A critical point of the analysis was to determine how the crack initiated, and subsequently propagated. High residual stresses and possible abnormal loading in conjunction with chemistry environments resulted in the Stress Corrosion Cracking (SCC) of the S08 outlet feeder bend. It is recognized that some of the causative factors implicated in the S08 failure apply to other outlet feeders. In particular, residual stresses in the non-stress-relieved, short-radius cold bent pipes will remain relatively high over the future life of the feeders. However, the risk of CANDU feeder failure by SCC is judged to be extremely low based on the evidence of the inspections carried out to date and the good performance record of feeder pipe in the CANDU industry. The channel was restored to its locked configuration, and the failed section of feeder replaced. (author)

  18. A feeder protection method against the phase-phase fault using symmetrical components

    DEFF Research Database (Denmark)

    Ciontea, Catalin-Iosif; Bak, Claus Leth; Blaabjerg, Frede

    2017-01-01

    The method of symmetrical components simplifies analysis of an electric circuit during the fault and represents an important tool for the protection engineers. In this paper, the symmetrical components of the fault current are used in a new feeder protection method for the maritime applications...... in a radial feeder, while its argument is an indicator of the fault direction. Precisely these information are used in this paper to detect the phase-phase fault and to indicate the faulted section of the feeder. Using PSCAD, the new method is implemented in a test Medium Voltage feeder with variable...

  19. limit loads for wall-thinning feeder pipes under combined bending and internal pressure

    International Nuclear Information System (INIS)

    Je, Jin Ho; Lee, Kuk Hee; Chung, Ha Joo; Kim, Ju Hee; Han, Jae Jun; Kim, Yun Jae

    2009-01-01

    Flow Accelerated Corrosion (FAC) during inservice conditions produces local wall-thinning in the feeder pipes of CANDU. The Wall-thinning in the feeder pipes is main degradation mechanisms affecting the integrity of piping systems. This paper discusses the integrity assessment of wall-thinned feeder pipes using limit load analysis. Based on finite element limit analyses, this paper compare limit loads for wall-thinning feeder pipes under combined bending and internal pressure with proposed limit loads. The limit loads are determined from limit analyses based on rectangular wall-thinning and elastic-perfectly-plastic materials using the large geometry change.

  20. Safe, Non-Corrosive Dielectric Fluid for Stagnating Radiator Thermal Control System, Phase II

    Data.gov (United States)

    National Aeronautics and Space Administration — Paragon Space Development Corporation proposes to develop a single-loop, non-toxic, active pumped radiator design with robust, reliable operation near stagnation...

  1. Safe, Non-Corrosive Dielectric Fluid for Stagnating Radiator Thermal Control System, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — Paragon proposes to develop a single-loop, non-toxic, stagnating active pumped loop thermal control design for NASA's Orion or Lunar Surface Access Module (LSAM)...

  2. DYNAMICS OF VIBRATION FEEDERS WITH A NONLINEAR ELASTIC CHARACTERISTIC

    Directory of Open Access Journals (Sweden)

    V. I. Dyrda

    2017-04-01

    Full Text Available Purpose. Subject to the smooth and efficient operation of each production line, is the use of vehicles transporting high specification. It worked well in practice for transporting construction machines, which are used during the vibration. The use of vibration machines requires optimization of their operation modes. In the form of elastic link in them are increasingly using rubber-metallic elements, which are characterized by nonlinear damping properties. So it is necessary to search for new, more modern, methods of calculation of dynamic characteristics of the vibration machines on the properties of rubber as a cushioning material. Methodology. The dynamics of vibration machine that is as elastic rubber block units and buffer shock absorbers limiting the amplitude of the vibrations of the working body. The method of determining amplitude-frequency characteristics of the vibrating feeder is based on the principle of Voltaire, who in the calculations of the damping properties of the dampers will allow for elastic-hereditary properties of rubber. When adjusting the basic dynamic stiffness of the elastic ties and vibratory buffers, using the principle of heredity rubber properties, determine the dependence of the amplitude of the working body of the machine vibrations. This method is called integro-operator using the fractional-exponential kernels of relaxation. Findings. Using the derived formula for determining the amplitude of the resonance curve is constructed one-mass nonlinear system. It is established that the use of the proposed method of calculation will provide a sufficiently complete description of the damping parameters of rubber-metallic elements and at the same time be an effective means of calculating the amplitude-frequency characteristics of nonlinear vibration systems. Originality. The authors improved method of determining damping characteristics of rubber-metallic elements and the amplitude-frequency characteristics of nonlinear

  3. Do broilers prefer to eat from a certain type of feeder?

    Directory of Open Access Journals (Sweden)

    DP Neves

    2010-09-01

    Full Text Available This study compared three types of feeders for broilers: Fênix, Tube and Automatic feeders. Bird's feeding behavior and preference were considered in this the evaluation. Preference was assessed by examining birds' behavioral activities, such as eating, standing and lying around the equipments, and meal duration as function of the environmental variables. Data on the behavioral activities and meal size were collected in a broiler commercial farm using a portable video camera, and the direct footages were analyzed. The time spent in each activity, feeding bout duration and time spent near the trough were statistically analyzed using the test of means and medians. Pearson's correlation test was used to evaluate the relationship between ambient environmental data and the time of feeding. A prospective scenario was established and data were pair wised compared to it. There were interactions between environmental characteristics and feeding and lying down activities during the experiment. Eating behavior was more frequent in the area around the Tube feeder. The duration of feeding time was higher when the birds used the Tube feeder (214 ± 28s, followed by the use of the Fênix feeder (123 ± 17s and the Automatic feeder (77 ± 29s. Birds preferred eating from the Tube feeder probably due to the absence of the partition grid above the feeder plate.

  4. Flow accelerated corrosion of carbon steel feeder pipes from Indian reactors

    International Nuclear Information System (INIS)

    Singh, J.L.; Kumar, Umesh; Kumawat, N.; Kumar, Sunil; Anantharaman, S.; Kain, Vivekanand

    2011-01-01

    En-masse feeder replacement was done at RAPS-2 after occurrence of a pinhole leak in B12 (S) outlet feeder elbow. Some of the feeders, removed after a service of 15.67 EFPY were received for detailed investigation. Ultrasonic thickness measurement of the feeders was carried out to ascertain the loss in wall thickness due to Flow Accelerated Corrosion (FAC) and marking the region of interest from outside. Surface morphology of inner surface of a number of feeder samples were carried out by SEM near the HAZ and adjoining area. Maximum FAC had occurred in the heat-affected zone of the weld in 32 NB elbows. Weld was affected to a lower extent than the parent metal due to higher chromium content. IGSCC cracks were also observed in parent metal portion of the middle elbow in 32 NB outlet feeder pipe due to bending residual stresses. There are two life limiting reasons to curtail the useful life in the reactors namely FAC and IGSCC. The problem of FAC can be reduced by increasing chromium content and reducing the flow velocity by opting for higher diameter feeder pipes. The welding defects and residual stresses in HAZ and surrounding areas are detrimental for FAC and IGSCC in the elbow region. This paper presents some of the microstructural observations and findings on FAC to explain the mechanism of degradation of feeders. (author)

  5. Growth inhibition of mouse embryonic stem (ES) cells on the feeders ...

    African Journals Online (AJOL)

    ajl4

    Mouse embryonic stem cells (mESCs) can be propagated in vitro on the feeders of mouse embryonic fibroblasts. In this study, we found growth inhibition of mESCs cultured on embryonic fibroblast feeders derived from different livestock animals. Under the same condition, mESCs derived from mouse embryonic fibroblast ...

  6. Bird Feeders as Locations for Skunk Uptake of Oral Rabies Vaccine Baits.

    Science.gov (United States)

    Theimer, Tad; Talk, Tisheena; Johnson, Shylo; Bergman, David L

    2017-04-01

    Significantly more (54%, P=0.003) placebo baits placed under 26 bird feeders in Arizona, US were removed by striped skunks ( Mephitis mephitis ) than at paired, nonfeeder locations (19%). Baiting at bird feeders could supplement traditional oral rabies vaccine bait placement in urban-suburban areas while engaging the public in rabies control efforts.

  7. Configuration and validation of dynamic simulation for design of vibratory bowl feeders

    DEFF Research Database (Denmark)

    Mathiesen, Simon; Ellekilde, Lars Peter

    2016-01-01

    Vibratory bowl feeders (VBF) are widely used in industry, but their design process is time consuming. This paper outlines an approach for the automatic design of such feeders, and utilizes rigid body simulation for evaluating design configurations. To ensure the applicability of the simulation...

  8. Evaluation of options for life cycle management of feeder cracking at the Point Lepreau Generating Station

    International Nuclear Information System (INIS)

    Gendron, T.S.; Slade, J.P.

    2003-01-01

    The CANDU industry has a predictive capability for most Heat Transport System (HTS) degradation issues that allows utilities to apply cost-effective maintenance programs. The standard approach for maintenance programs is focussed inspection and planned replacement. Some examples of degradation issues with deterministic failure rates are feeder thinning, and pressure tube elongation and deuterium ingress. However, the cracking observed in Point Lepreau Generating Station (PLGS) outlet feeder first bends is one notable exception to this behaviour. A predictive capability for feeder cracking does not currently exist for several reasons. First, the mechanism of feeder cracking, stress corrosion cracking (SCC), has to some degree a random nature. Second, although a probable environment causing cracking has been identified, the precise stress and environmental conditions for feeder crack initiation and propagation have not been defined. Finally, the very low incidence of feeder cracking observed to-date (four, all at PLGS) precludes a probabilistic or statistical prediction of failure rate. Generally, utilities select a Life Cycle Management Plan that ensures safe operation and has the lowest Net Present Value cost. In preparing a Feeder Life Cycle Management Plan, New Brunswick Power (NBP) has recognized that the Net Present Value cost is very sensitive to failure rate. Since the failure rate for feeder cracking is not well defined, the following three scenarios were considered to bound the probability of future failures at PLGS. (author)

  9. Heuristic method for reactive energy management in distribution feeders

    International Nuclear Information System (INIS)

    Hamouda, Abdellatif; Lakehal, Nadia; Zehar, Khaled

    2010-01-01

    This paper proposes an efficient method for solving shunt capacitors sizing problem in radial distribution feeders. For this typical multi-objective optimisation problem, the optimal number, sizes and locations of fixed shunt capacitors are determined using a sensitivity-based heuristic solution. In this method, based on Markov chains, the number of variables to be optimised is reduced by using the node sensitivities to locate capacitors. Only a limited number of critical nodes satisfy the problem constraints and are considered for receiving standard shunt capacitors that maximise a net saving function. In order to overcome any over-compensation, the voltage admissible limits, imposed by many authors, are substituted by a new constraint on the branch reactive currents. To demonstrate the effectiveness and feasibility of the proposed approach, comparative studies were conducted on several test systems. The results we got were promising compared to those given by previous published techniques.

  10. Microplastic in a macro filter feeder: Humpback whale Megaptera novaeangliae.

    Science.gov (United States)

    Besseling, E; Foekema, E M; Van Franeker, J A; Leopold, M F; Kühn, S; Bravo Rebolledo, E L; Heße, E; Mielke, L; IJzer, J; Kamminga, P; Koelmans, A A

    2015-06-15

    Marine filter feeders are exposed to microplastic because of their selection of small particles as food source. Baleen whales feed by filtering small particles from large water volumes. Macroplastic was found in baleen whales before. This study is the first to show the presence of microplastic in intestines of a baleen whale (Megaptera novaeangliae). Contents of its gastrointestinal tract were sieved, dissolved in 10% potassium hydroxide and washed. From the remaining dried material, potential synthetic polymer particles were selected based on density and appearance, and analysed by Fourier transform infrared (FTIR) spectroscopy. Several polymer types (polyethylene, polypropylene, polyvinylchloride, polyethylene terephthalate, nylon) were found, in varying particle shapes: sheets, fragments and threads with a size of 1mm to 17cm. This diversity in polymer types and particle shapes, can be interpreted as a representation of the varying characteristics of marine plastic and the unselective way of ingestion by M. novaeangliae. Copyright © 2015 Elsevier Ltd. All rights reserved.

  11. Nitrogen fixed by cyanobacteria is utilized by deposit-feeders.

    Science.gov (United States)

    Karlson, Agnes M L; Gorokhova, Elena; Elmgren, Ragnar

    2014-01-01

    Benthic communities below the photic zone depend for food on allochthonous organic matter derived from seasonal phytoplankton blooms. In the Baltic Sea, the spring diatom bloom is considered the most important input of organic matter, whereas the contribution of the summer bloom dominated by diazotrophic cyanobacteria is less understood. The possible increase in cyanobacteria blooms as a consequence of eutrophication and climate change calls for evaluation of cyanobacteria effects on benthic community functioning and productivity. Here, we examine utilization of cyanobacterial nitrogen by deposit-feeding benthic macrofauna following a cyanobacteria bloom at three stations during two consecutive years and link these changes to isotopic niche and variations in body condition (assayed as C:N ratio) of the animals. Since nitrogen-fixing cyanobacteria have δ(15)N close to -2‰, we expected the δ(15)N in the deposit-feeders to decrease after the bloom if their assimilation of cyanobacteria-derived nitrogen was substantial. We also expected the settled cyanobacteria with their associated microheterotrophic community and relatively high nitrogen content to increase the isotopic niche area, trophic diversity and dietary divergence between individuals (estimated as the nearest neighbour distance) in the benthic fauna after the bloom. The three surface-feeding species (Monoporeia affinis, Macoma balthica and Marenzelleria arctia) showed significantly lower δ(15)N values after the bloom, while the sub-surface feeder Pontoporeia femorata did not. The effect of the bloom on isotopic niche varied greatly between stations; populations which increased niche area after the bloom had better body condition than populations with reduced niche, regardless of species. Thus, cyanobacterial nitrogen is efficiently integrated into the benthic food webs in the Baltic, with likely consequences for their functioning, secondary production, transfer efficiency, trophic interactions, and

  12. Development of an extruder-feeder biomass direct liquefaction process

    Energy Technology Data Exchange (ETDEWEB)

    White, D.H.; Wolf, D. (Arizona Univ., Tucson, AZ (United States). Dept. of Chemical Engineering)

    1991-10-01

    As an abundant, renewable, domestic energy resource, biomass could help the United States reduce its dependence on imported oil. Biomass is the only renewable energy technology capable of addressing the national need for liquid transportation fuels. Thus, there is an incentive to develop economic conversion processes for converting biomass, including wood, into liquid fuels. Through research sponsored by the US DOE's Biomass Thermochemical Conversion Program, the University of Arizona has developed a unique biomass direct liquefaction system. The system features a modified single-screw extruder capable of pumping solid slurries containing as high as 60 wt% wood flour in wood oil derived vacuum bottoms at pressures up to 3000 psi. The extruder-feeder has been integrated with a unique reactor by the University to form a system which offers potential for improving high pressure biomass direct liquefaction technology. The extruder-feeder acts simultaneously as both a feed preheater and a pumping device for injecting wood slurries into a high pressure reactor in the biomass liquefaction process. An experimental facility was constructed and following shakedown operations, wood crude oil was produced by mid-1985. By July 1988, a total of 57 experimental continuous biomass liquefaction runs were made using White Birch wood feedstock. Good operability was achieved at slurry feed rates up to 30 lb/hr, reactor pressures from 800 to 3000 psi and temperatures from 350{degree}C to 430{degree}C under conditions covering a range of carbon monoxide feed rates and sodium carbonate catalyst addition. Crude wood oils containing as little as 6--10 wt% residual oxygen were produced. 38 refs., 82 figs., 26 tabs.

  13. Continuation Power Flow Analysis for PV Integration Studies at Distribution Feeders

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Jiyu; Zhu, Xiangqi; Lubkeman, David L.; Lu, Ning; Samaan, Nader A.

    2017-10-30

    This paper presents a method for conducting continuation power flow simulation on high-solar penetration distribution feeders. A load disaggregation method is developed to disaggregate the daily feeder load profiles collected in substations down to each load node, where the electricity consumption of residential houses and commercial buildings are modeled using actual data collected from single family houses and commercial buildings. This allows the modeling of power flow and voltage profile along a distribution feeder on a continuing fashion for a 24- hour period at minute-by-minute resolution. By separating the feeder into load zones based on the distance between the load node and the feeder head, we studied the impact of PV penetration on distribution grid operation in different seasons and under different weather conditions for different PV placements.

  14. A Feeder-Bus Dispatch Planning Model for Emergency Evacuation in Urban Rail Transit Corridors

    Science.gov (United States)

    Wang, Yun; Yan, Xuedong; Zhou, Yu; Zhang, Wenyi

    2016-01-01

    The mobility of modern metropolises strongly relies on urban rail transit (URT) systems, and such a heavy dependence causes that even minor service interruptions would make the URT systems unsustainable. This study aims at optimally dispatching the ground feeder-bus to coordinate with the urban rails’ operation for eliminating the effect of unexpected service interruptions in URT corridors. A feeder-bus dispatch planning model was proposed for the collaborative optimization of URT and feeder-bus cooperation under emergency situations and minimizing the total evacuation cost of the feeder-buses. To solve the model, a concept of dummy feeder-bus system is proposed to transform the non-linear model into traditional linear programming (ILP) model, i.e., traditional transportation problem. The case study of Line #2 of Nanjing URT in China was adopted to illustrate the model application and sensitivity analyses of the key variables. The modeling results show that as the evacuation time window increases, the total evacuation cost as well as the number of dispatched feeder-buses decrease, and the dispatched feeder-buses need operate for more times along the feeder-bus line. The number of dispatched feeder-buses does not show an obvious change with the increase of parking spot capacity and time window, indicating that simply increasing the parking spot capacity would cause huge waste for the emergent bus utilization. When the unbalanced evacuation demand exists between stations, the more feeder-buses are needed. The method of this study will contribute to improving transportation emergency management and resource allocation for URT systems. PMID:27676179

  15. Effect of bed configuration on pebble flow uniformity and stagnation in the pebble bed reactor

    Energy Technology Data Exchange (ETDEWEB)

    Gui, Nan; Yang, Xingtuan [Institute of Nuclear and New Energy Technology of Tsinghua University, Key Laboratory of Advanced Reactor Engineering and Safety, Ministry of Education, Beijing 100084 (China); Tu, Jiyuan [Institute of Nuclear and New Energy Technology of Tsinghua University, Key Laboratory of Advanced Reactor Engineering and Safety, Ministry of Education, Beijing 100084 (China); School of Aerospace, Mechanical and Manufacturing Engineering, RMIT University, Melbourne, VIC 3083 (Australia); Jiang, Shengyao, E-mail: jiangshy@tsinghua.edu.cn [Institute of Nuclear and New Energy Technology of Tsinghua University, Key Laboratory of Advanced Reactor Engineering and Safety, Ministry of Education, Beijing 100084 (China)

    2014-04-01

    Highlights: • Pebble flow uniformity and stagnation characteristics are very important for HTR-PM. • Arc- and brachistochrone-shaped configuration effects are studied by DEM simulation. • Best bed configurations with uniform flow and no stagnated pebbles are suggested. • Detailed quantified characteristics of bed configuration effects are shown for explanation. - Abstract: Pebble flow uniformity and stagnation characteristics are very important for the design of pebble bed high temperature gas-cooled reactor. Pebble flows inside some specifically designed contraction configurations of pebble bed are studied by discrete element method. The results show the characteristics of stagnation rates, recycling rates, radial distribution of pebble velocity and residence time. It is demonstrated clearly that the bed with a brachistochrone-shaped configuration achieves optimum levels of flow uniformity and recycling rate concentration, and almost no pebbles are stagnated in the bed. Moreover, the optimum choice among the arc-shaped bed configurations is demonstrated too. Detailed information shows the quantified characteristics of bed configuration effects on flow uniformity. In addition, a good design of the pebble bed configuration is suggested.

  16. Bird feeders and their effects on bird-window collisions at residential houses

    Directory of Open Access Journals (Sweden)

    Justine A. Kummer

    2015-12-01

    Full Text Available Feeding wild birds creates an important link between homeowners and conservation. The effects of bird feeders and year-round feeding on birds have not been well studied, however, particularly in relationship to bird-window collisions. We determined effects of bird feeder presence and placement on bird-window collisions at residential homes. Paired month-long trials in which a feeder was either present or absent for one month and then removed or added for the second month were completed at 55 windows at 43 houses. In each trial, homeowners were asked to search their study window daily for evidence of a bird-window collision. During the study there were 51 collisions when there was no bird feeder and 94 when the feeder was present. The season when each trial was set up was the best individual predictor of bird-window collisions. The largest number of collisions was observed during fall migration and the lowest during the winter months. There were no collisions at 26 of the study windows. High variance was observed in the number of collisions at different houses, indicating that effects of bird feeders are context dependent. Changing the occurrence, timing, and placement of feeders can alter collision rates but is only one of many factors that influence whether a residential house is likely to have a bird window-collision or not.

  17. Development of genetically modified eliminable human dermal fibroblast feeder cells for ocular surface regeneration medicine.

    Science.gov (United States)

    Li, Yingli; Inoue, Tomoyuki; Takamatsu, Fumihiko; Maeda, Naoyuki; Ohashi, Yuichi; Nishida, Kohji

    2013-11-15

    Cultured human corneal limbal stem/progenitor cells are usually established and maintained on feeder layers. However, animal feeder cells are associated with viral infection, pathogen transmission, and xenogenic contamination. All feeder cells also can be mixed easily into cell-sheet production, causing self-contamination. We developed a line of labeled, immortalized, eliminable human dermal fibroblast cells to eliminate these problems. The enhanced green fluorescent protein gene, human-derived telomerase reverse transcriptase gene, and herpes simplex virus thymidine kinase gene were transfected into human dermal fibroblast cells to establish labeled, immortalized, eliminable feeder cells. Established eliminable dermal fibroblasts (TERT+TK-D) were treated with mitomycin, cocultured with human limbal stem/progenitor cells to regenerate epithelium sheets, and compared with 3T3 feeder cells. Established TERT+TK-D feeder cells maintained immortalization, visualization, and eliminable characteristics during 6 months of continuous passages. The colony-forming efficiency of limbal stem/progenitor cells was similar in the TERT+TK-D group (11.77 ± 0.21%) and the 3T3 group (12.8 ± 1.61%) (P = 0.332). All cell sheets were well stratified into 4 to 5 layers. The TERT+TK-D group colonies and epithelial cell sheets showed weaker staining of corneal epithelium differentiation marker K3 than the 3T3 group and quantitative analysis of mRNA transcripts. Moreover, PCR analysis against the long terminal repeat sequence of the lentiviral vector integrated into the genetically modified feeder cells showed no contamination of ganciclovir-treated regeneration epithelial sheets. Genetically modified, labeled, immortalized, eliminable human dermal feeder cells are promising substitutes for 3T3 feeder cells for xenogeny-free ocular surface regeneration.

  18. Effects of Feeder Cells on Dopaminergic Differentiation of Human Embryonic Stem Cells

    Directory of Open Access Journals (Sweden)

    Zhenqiang Zhao

    2016-12-01

    Full Text Available Mouse embryonic fibroblasts (MEFs and human foreskin fibroblasts (HFFs are used for the culture of human embryonic stem cells (hESCs. MEFs and HFFs differed in their capacity to support the proliferation and pluripotency of hESCs and could affect cardiac differentiation potential of hESCs. The aim of this study was to evaluate the effect of MEFs and HFFs feeders on dopaminergic differentiation of hESCs lines. To minimize the impact of culture condition variation, two hESCs lines were cultured on mixed feeder cells (MFCs, MEFs: HFFs =1:1 and HFFs feeder respectively, and then were differentiated into DA neurons under the identical protocol. Dopaminergic differentiation was evaluated by immunocytochemistry, quantitative fluorescent real-time PCR (qRT-PCR, transmission and scanning electron microscopy, and patch clamp. Our results demonstrated that these hESCs-derived neurons were genuine and functional DA neurons. However, compared to hESCs line on MFCs feeder, hESCs line on HFFs feeder had a higher proportion of TH positive cells and expressed higher levels of FOXA2, PITX3, NURR1 and TH genes. In addition, the values of threshold intensity and threshold membrane potential of DA neurons from hESCs line on HFFs feeder were lower than those of DA neurons from hESCs line on the MFCs feeder. In conclusion, HFFs feeder not only facilitated the differentiation of hESCs cells into dopaminergic neurons, but also induced hESCs-derived DA neurons to express higher electrophysiological excitability. Therefore, feeder cells could affect not only dopaminergic differentiation potential of different hESCs lines, but also electrophysiological properties of hESCs-derived DA neurons.

  19. Feasibility and practice of nodular iron casting feeder-less production

    Directory of Open Access Journals (Sweden)

    ZHOU Gen

    2006-02-01

    Full Text Available The volumetric changes of castings and dimension changes of mould cavity occurring during liquid cooling and solidification of nodular iron castings were described. The feasibility and prerequisites to realize feeder-less production of nodular iron castings was analyzed and proved with practical examples. It was pointed out that the feeder-less foundry method is by no means a feeding-less method, and it was emphasized that adopting high carbon equivalent, high rigidity mould, simultaneous and synchronous solidification, and intensifying cooling capacity of the mould to increase feeding effect of the gating system are important to successfully realize feeder-less production of nodular iron castings.

  20. Feeding Against Gravity with Spot Feeders in High Silicon Ductile Iron

    DEFF Research Database (Denmark)

    Vedel-Smith, Nikolaj Kjelgaard; Tiedje, Niels Skat

    2014-01-01

    A test pattern, with three different moduli castings was developed to investigate methods to optimise feeding of high silicon ductile cast irons. Different feeder types, modulus, and locations were investigated using both an insulating and an exothermal sleeve material. Porosities were analysed......-hill against gravity. This effect may contribute to the thermal expansion created by the exothermal reaction. It was also found that the optimum feeder size does not scale linearly with the casting modulus but that larger casting modulus requires relatively smaller modulus feeders. The thermal gradient created...

  1. Active power filter equivalent to an infinite feeder for harmonic suppression in radial distribution systems

    DEFF Research Database (Denmark)

    Shen, Hong; Yang, Lili; Sun, Xiaofeng

    2016-01-01

    This study proposes to install a novel active power filter (IF-APF) mimicking the character of an infinitely long transmission line at the end of a radial feeder. The proposed IF-APF eliminates the reflected wave and realises the background harmonic voltage suppression capability throughout...... the feeder by mimicking the characteristic of an infinite feeder. The proposed IF-APF shows a better harmonic damping performance than the traditional resistive active power filter (R-APF). Moreover, the proposed IF-APF achieves a better harmonic suppression performance than the traditional R-APF, especially...

  2. Three dimensional finite element analysis of weld overlay application on a plastically formed feeder tube

    Energy Technology Data Exchange (ETDEWEB)

    Ku, F.H.; Riccardella, P.C.; Lashley, M.S. [Structural Integrity Associates Inc., California (United States); Chen, Y. [Structural Integrity Associates, Inc., Ontario (Canada); Yee, R.K. [San Jose State Univ., California (United States)

    2010-07-01

    This paper presents a finite element analysis (FEA) model to predict the residual stresses in a tight-radius warm bend feeder tube in a CANDU nuclear reactor coolant system throughout the various stages of the manufacturing and welding processes, including feeder tube forming, Grayloc hub weld, and weld overlay application. The FEA employs 3-D elastic-plastic technology with large deformation capability to predict the residual stresses due to the feeder tube forming and various welding processes. The results demonstrate that the FEA method captures the residual stress trends resulted from warm bending and weld overlay with acceptable accuracy. (author)

  3. THERMOSS: A thermohydraulic model of flow stagnation in a horizontal fuel channel

    International Nuclear Information System (INIS)

    Gulshani, P.; Caplan, M.Z.; Spinks, N.J.

    1984-01-01

    A model, called THERMOSS, is developed to compute the duration of stagnation in a CANDU reactor fuel channel with subcooled, stagnant initial conditions. The model solves, in closed form, the one dimensional, two-fluid conservation equations. In the computation of the duration of stagnation, the channel water level is an important intermediate variable because it determines the amount of steam production. A feature of the model is that water level is determined by a momentum balance between frictional pressure drop in the steam phase and hydrostatic head in the liquid phase. This is in contrast to an ealier model in which the level was determined from mass balance considerations. A satisfactory agreement between the predicted and experimentally observed channel water level and duration of stagnation is obtained. (orig.)

  4. 'BREAKS' Protocol for Breaking Bad News.

    Science.gov (United States)

    Narayanan, Vijayakumar; Bista, Bibek; Koshy, Cheriyan

    2010-05-01

    Information that drastically alters the life world of the patient is termed as bad news. Conveying bad news is a skilled communication, and not at all easy. The amount of truth to be disclosed is subjective. A properly structured and well-orchestrated communication has a positive therapeutic effect. This is a process of negotiation between patient and physician, but physicians often find it difficult due to many reasons. They feel incompetent and are afraid of unleashing a negative reaction from the patient or their relatives. The physician is reminded of his or her own vulnerability to terminal illness, and find themselves powerless over emotional distress. Lack of sufficient training in breaking bad news is a handicap to most physicians and health care workers. Adherence to the principles of client-centered counseling is helpful in attaining this skill. Fundamental insight of the patient is exploited and the bad news is delivered in a structured manner, because the patient is the one who knows what is hurting him most and he is the one who knows how to move forward. Six-step SPIKES protocol is widely used for breaking bad news. In this paper, we put forward another six-step protocol, the BREAKS protocol as a systematic and easy communication strategy for breaking bad news. Development of competence in dealing with difficult situations has positive therapeutic outcome and is a professionally satisfying one.

  5. Minimal incorporation of Deepwater Horizon oil by estuarine filter feeders

    International Nuclear Information System (INIS)

    Fry, Brian; Anderson, Laurie C.

    2014-01-01

    Highlights: • Oil from the Deepwater Horizon oil spill entered Louisiana bays in mid-2010. • Oil was used minimally (<1%) in diets of mussels and barnacles. • Also, oil did not enhance planktonic respiration rates. • Use of oil carbon was relatively small in these productive estuarine food webs. - Abstract: Natural abundance carbon isotope analyses are sensitive tracers for fates and use of oil in aquatic environments. Use of oil carbon in estuarine food webs should lead to isotope values approaching those of oil itself, −27‰ for stable carbon isotopes reflecting oil origins and −1000‰ for carbon-14 reflecting oil age. To test for transfer of oil from the 2010 Deepwater Horizon spill into estuarine food webs, filter-feeding barnacles (Balanus sp.) and marsh mussels (Geukensia demissa) were collected from Louisiana estuaries near the site of the oil spill. Carbon-14 analyses of these animals from open waters and oiled marshes showed that oil use was <1% and near detection limits estimated at 0.3% oil incorporation. Respiration studies showed no evidence for enhanced microbial activity in bay waters. Results are consistent with low dietary impacts of oil for filter feeders and little overall impact on respiration in the productive Louisiana estuarine systems

  6. Automatic feeder for small fish held in tanks

    Science.gov (United States)

    Joeris, Leonard S.

    1965-01-01

    The Northville (Michigan) Biological Station has been a center for study of the developmental morphology of coregonid fishes. This work requires the production of numerous individual series of lake herring, lake whitefish, and several species of chubs from parent fish of positively known identity. The offspring of individual pairs or groups of fish must be held in individual tanks from the time they hatch until they reach maturity. One of the important problems in this project has been the poor growth of most fish. Though some have grown well, their growth has been less than that of the same species in nature, and a few fish from each hatch have grown very slowly. Irregularity of feeding may contribute to the slow growth of laboratory fish. The hatchery caretaker feeds them several times during his 8-hour workday, but they must go without food during the remaining 16 hours. The high metabolic rate of small fish, however, appears to make them strongly inclined toward almost continual feeding. Belief that greater, more regular food consumption would result from a mechanical feeder providing a continuous supply of food over a longer period of the day led to development of the equipment described in this paper.

  7. Propagation of microwave beams through the stagnation zone in an inhomogeneous plasma

    Energy Technology Data Exchange (ETDEWEB)

    Tereshchenko, M. A., E-mail: maxt@inbox.ru [Russian Academy of Sciences, Prokhorov General Physics Institute (Russian Federation)

    2017-01-15

    A study is made of the microwave beam evolution due to passing through the stagnation zone, where the group velocity vanishes, thus making the paraxial approximation for the wavefield inappropriate. An extension to the standard beam tracing technique is suggested that allows one to calculate the microwave beam parameters on either branch of its path apart from the stagnation zone, omitting the calculation of the wavefield inside it. Application examples of the extended technique are presented for the case of microwave reflection from the upper hybrid resonance layer in a tokamak plasma.

  8. Stagnation-point flow over a stretching/shrinking sheet in a nanofluid

    OpenAIRE

    Bachok, Norfifah; Ishak, Anuar; Pop, Ioan

    2011-01-01

    An analysis is carried out to study the steady two-dimensional stagnation-point flow of a nanofluid over a stretching/shrinking sheet in its own plane. The stretching/shrinking velocity and the ambient fluid velocity are assumed to vary linearly with the distance from the stagnation point. The similarity equations are solved numerically for three types of nanoparticles, namely copper, alumina, and titania in the water-based fluid with Prandtl number Pr = 6.2. The skin friction coefficient, Nu...

  9. Decision Support for Optimal Repositioning of Containers in a Feeder System

    Directory of Open Access Journals (Sweden)

    Danijela Tuljak-Suban

    2008-03-01

    Full Text Available The transport of empty containers represents a seriousproblem in the fast growing sphere of maritime container transport.The most widespread type of container transport organizationin maritime transport is the hub and spoke mode, whichenables the transport of a great number of containers via largevessels between hub ports, from where feeder ships transport tosmaller ports that thus gravitate to the central hub port. The articlecontains a detailed analysis of the northern Adriatic portsand the feeder connections with the hub ports of the Mediterranean.A two-level VRPPD (Vehicle Routing Problem withPickup and Delivery problem is modelled on a graph, wherethe transport of full containers is privileged over the transport ofempty containers. This enables the simulation of the feeder systemin the n01them Adriatic, meaning that it shows the ship'soperator the movement programme with minimal transportcosts for the superfluous empty containers in the complex of theregular transports of full containers in the feeder system.

  10. Voltage Support Study of Smart PV Inverters on a High-Photovoltaic Penetration Utility Distribution Feeder

    Energy Technology Data Exchange (ETDEWEB)

    Ding, Fei; Pratt, Annabelle; Bialek, Tom; Bell, Frances; McCarty, Michael; Atef, Kahveh; Nagarajan, Adarsh; Gotseff, Peter

    2016-11-21

    This paper reports on tools and methodologies developed to study the impact of adding rooftop photovoltaic (PV) systems, with and without the ability to provide voltage support, on the voltage profile of distribution feeders. Simulation results are provided from a study of a specific utility feeder. The simulation model of the utility distribution feeder was built in OpenDSS and verified by comparing the simulated voltages to field measurements. First, we set all PV systems to operate at unity power factor and analyzed the impact on feeder voltages. Then we conducted multiple simulations with voltage support activated for all the smart PV inverters. These included different constant power factor settings and volt/VAR controls.

  11. Consistency of Trend Break Point Estimator with Underspecified Break Number

    Directory of Open Access Journals (Sweden)

    Jingjing Yang

    2017-01-01

    Full Text Available This paper discusses the consistency of trend break point estimators when the number of breaks is underspecified. The consistency of break point estimators in a simple location model with level shifts has been well documented by researchers under various settings, including extensions such as allowing a time trend in the model. Despite the consistency of break point estimators of level shifts, there are few papers on the consistency of trend shift break point estimators in the presence of an underspecified break number. The simulation study and asymptotic analysis in this paper show that the trend shift break point estimator does not converge to the true break points when the break number is underspecified. In the case of two trend shifts, the inconsistency problem worsens if the magnitudes of the breaks are similar and the breaks are either both positive or both negative. The limiting distribution for the trend break point estimator is developed and closely approximates the finite sample performance.

  12. Route Design Model of Feeder Bus Service for Urban Rail Transit Stations

    Directory of Open Access Journals (Sweden)

    Zhenjun Zhu

    2017-01-01

    Full Text Available As an important part of urban public transportation systems, the feeder bus fills a service gap left by rail transit, effectively extending the range of rail transit’s service and solving the problem of short-distance travel and interchanges. By defining the potential demand of feeder bus services and considering its relationship with the traffic demands of corresponding staging areas, the distance between road and rail transit, and the repetition factor of road bus lines, this paper established a potential demand model of roads by opening feeder bus services and applying a logit model for passenger flow distribution. Based on a circular route model, a route starting and ending at urban rail transit stations was generated, and a genetic algorithm was then applied to solve it. The Wei-Fang community of Shanghai was selected as the test area. Per the model and algorithm, the feeder route length was conformed to a functional orientation of short-distance travel and the feeder service of a feeder bus; the route mostly covered where conventional bus lines were fewer, which is a finding that is in agreement with the actual situation; the feasibility of the model and algorithm was verified.

  13. Manufacture and test of seismic bellows for ITER magnet feeder

    International Nuclear Information System (INIS)

    Liu, Chen; Lu, Kun; Sheng, Liang; Song, Yuntao; Su, Jinjin; Su, Man; Gung, Chenyu

    2016-01-01

    Highlights: • The design of the double bellows was iterated with the results of analysis based on the Expansion Joint Manufacturers Association (EJMA) standard. • The seismic bellows was tested with cyclic pressurization of the interlayer space to 2 bars absolute pressure for 5 cycles. • 200 cycles of tensile fatigue test with 90 mm of stretching from the nominal design length. • A full tensile test with 315 mm of stretching from its nominal length was conducted. • The prototype bellows was qualified for its leak tightness (less than 1 × 10 −9 Pam 3 /s of helium) at all time during the qualification test. - Abstract: This paper presents the key manufacturing and testing processes of the prototype ITER feeder seismic bellows. The design of the double bellows was iterated with the results of analysis based on the Expansion Joint Manufacturers Association (EJMA) standard. Each inner and outer bellows was supported in dedicated molds and formed by a hydraulic pressure machine rated at 800 tons. The double bellows were constructed by welding individual collars to the end flanges. The seismic bellows was tested with cyclic pressurization of the interlayer space to 2 bars absolute pressure for 5 cycles. This was followed by 200 cycles of tensile fatigue test with 90 mm of stretching from the nominal design length. After the mechanical fatigue test, a full tensile test with 315 mm of stretching from its nominal length was conducted. Helium leak tests, with the sensitivity of the helium leak detector set to 1 × 10 −9 Pa m 3 /s of helium, were performed at different stages of pressure and mechanical tests. The prototype bellows was qualified for its leak tightness at all time during the qualification test.

  14. A multifactorial approach to explaining the stagnation in national smoking rates


    DEFF Research Database (Denmark)

    Pisinger, Charlotta; Jørgensen, Torben; Toft, Ulla

    2018-01-01

    of tobacco had remained almost unchanged, tobacco control legislation and anti-smoking campaigns had not been very intensive, assistance to quit and the Health Authority's manpower allocated to tobacco control had decreased temporarily while the use of e-cigarettes had increased in the stagnation period...

  15. Prediction and experimental validation of stagnation temperature attained by a solar cooker of hot box type

    Energy Technology Data Exchange (ETDEWEB)

    Narasimha Rao, A. V; Srikrishna, D. V. N [Warangal (India)

    2000-07-01

    A hot box type solar cooker, having double glass covers and a plane mirror reflector, is tested for stagnation temperature. A computer code is developed based on the analytical model proposed by Vaishya et. al. The global and beam components of solar radiation measured at Warangal are made use to predict the stagnation temperature of the cooker. The observed values of stagnation temperature at Warangal are compared with those of predicted values. A good agreement of the measured and observed values of the stagnation temperature is observed during the afternoon period. The lag in the observed values during the forenoon may be due to thermal inertia of the cooker. [Spanish] Se probo una estufa solar de tipo caja caliente con cubiertas dobles de vidrio y un espejo reflector plano para medir la temperatura de estancamiento. Se desarrollo un codigo de computacion basado en el modelo analitico propuesto por Vaishya et. al. Los componentes de la radiacion solar globales y de rayo medidos en Warangal se usan para predecir la temperatura de estancamiento de la estufa. Los valores observados de la temperatura de estancamiento en Warangal se comparan con los valores predichos. Se aprecia una buena concidencia de los valores medidos y observados de la temperatura de estancamiento durante el periodo de la tarde. El retraso de los valores observados durante la manana puede ser debido a la inercia termica de la estufa.

  16. Void fraction distribution in a heated rod bundle under flow stagnation conditions

    Energy Technology Data Exchange (ETDEWEB)

    Herrero, V.A.; Guido-Lavalle, G.; Clausse, A. [Centro Atomico Bariloche and Instituto Balseiro, Bariloche (Argentina)

    1995-09-01

    An experimental study was performed to determine the axial void fraction distribution along a heated rod bundle under flow stagnation conditions. The development of the flow pattern was investigated for different heat flow rates. It was found that in general the void fraction is overestimated by the Zuber & Findlay model while the Chexal-Lellouche correlation produces a better prediction.

  17. Atmospheric stagnation, recirculation and ventilation potential of several sites in Argentina

    Science.gov (United States)

    Venegas, L. E.; Mazzeo, N. A.

    Conditions for stagnation, recirculation and ventilation potential of the atmosphere were studied in five argentine cities: Resistencia, Córdoba, Buenos Aires, Mar del Plata and Comodoro Rivadavia, located in different regions of the country. Wind run and recirculation factors were calculated for a 24-h transport time using 2 years of hourly surface measurements of wind speed and direction. The largest stagnation frequency (45% of the time) was observed in Resistencia, located in the northeastern part of the country, in an area where winds are weak. The least frequency of stagnations (2%) was observed in Comodoro Rivadavia, in the southern region of the country, a region dominated by strong westerly winds. Comodoro Rivadavia and Córdoba registered the largest frequency of recirculations. Comodoro Rivadavia exposed to sea-land breezes and Córdoba, located on a complex terrain area and exposed to local circulations, experienced recirculation events during 10% of the time. Good atmospheric ventilation occurs when a high value of wind run and a low value of the recirculation factor are observed and it can be associated with the atmosphere's capacity to replace polluted air with clean air. Ventilation events occurred 58% of the time at Comodoro Rivadavia, 52% at Mar del Plata, 40% at Buenos Aires, 35% at Córdoba and 18% at Resistencia. In general, stagnation was more frequently observed during autumn and winter, recirculation during spring and summer and good ventilation conditions occurred during spring.

  18. Development of a feeder device for logging residue for a drum chipper; Hakkurin syoetoen kehittaeminen energiapuulle

    Energy Technology Data Exchange (ETDEWEB)

    Leinonen, T.; Kemppainen, J.P. [Oulu Univ. (Finland). Dept. of Mechanical Engineering

    1997-12-01

    The aim of this project is to increase the productivity of a large drum chipper by developing a feeder device to be used especially when chipping logging residue. Logging residue from regeneration areas is the most important reserve of forest biomass for the production of renewable energy in Finland. It is possible ecologically and economically to use about 5 million m{sup 3} of logging residue yearly for energy purposes. Currently both large lorry based chippers and smaller forwarder based chippers are used for chipping logging residue. However even the latest versions of these chippers are not well equipped for chipping logging residue. The ball like shape of residue piles causes blockades, if too large amounts of residue are fed into the chipper. Keeping the material flow even is difficult. In this project a prototype of a feeder device will be designed and manufactured to exactly find out the problems, that occur when feeding logging residue to a chipper. The designed prototype is based on a tubular chassis, which supports a conveyor made of steel plates. Prototype also has a 2,5 m wide feeding table and a feeder roll, which is located above the conveyor just before the chipper opening. Both the conveyor and the feeder roll are powered by hydraulic motors. The maximum feeding force is 20 kN. For research purposes both hydraulic pressure and flow can be adjusted individually for both motors. During 1996 activities included designing and building the prototype feeder device. In 1997 the prototype will be tested to find out possible problems, which need to be cured. After problems are solved and other improvements are made, the feeder device will be installed to an existing chipper and then tested again to determine the productivity of the new feeder device compared to the old unit. (orig.)

  19. Impact of V2G on Distribution Feeder: A Power Loss Reduction Approach

    Science.gov (United States)

    Chukwu, Uwakwe C.; Mahajan, Satish M.

    2013-08-01

    The penetration of Vehicle-to-Grid (V2G) into the electrical distribution system has potential to create room for many operational benefits. A V2G facility installed on a distribution feeder line segment may affect power loss in the distribution system. Mathematical models are developed to study how magnitude of V2G reactive power injection and different mixes of uniformly distributed loads and lumped loads can impact power loss on a distribution system feeder. The V2G facilities assumed in this research are V2G parking lots with provision for injecting reactive currents into the feeder of a distribution network. It is shown that loss reduction can be greatly influenced by the pattern of loading, the amount of V2G reactive injection as well as position and number of V2G parking lot along the feeder segment. Useful results are obtained, with a promise that more than 95% power loss reduction (relative to power loss in the system without V2G installed) is possible by optimally locating a V2G parking lot along the feeder. It is observed that location and capacity injection of a V2G facility are the most critical for loss reduction. It was concluded that proper system planning and operational practice are required in order to reduce power losses.

  20. Comparing the engineering program feeders from SiF and convention models

    Science.gov (United States)

    Roongruangsri, Warawaran; Moonpa, Niwat; Vuthijumnonk, Janyawat; Sangsuwan, Kampanart

    2018-01-01

    This research aims to compare the relationship between two types of engineering program feeder models within the technical education systems of Rajamangala University of Technology Lanna (RMUTL), Chiangmai, Thailand. To illustrate, the paper refers to two typologies of feeder models, which are the convention and the school in factory (SiF) models. The new SiF model is developed through a collaborative educational process between the sectors of industry, government and academia, using work-integrated learning. The research methodology were use to compared features of the the SiF model with conventional models in terms of learning outcome, funding budget for the study, the advantages and disadvantages from the point of view of students, professors, the university, government and industrial partners. The results of this research indicate that the developed SiF feeder model is the most pertinent ones as it meet the requirements of the university, the government and the industry. The SiF feeder model showed the ability to yield positive learning outcomes with low expenditures per student for both the family and the university. In parallel, the sharing of knowledge between university and industry became increasingly important in the process, which resulted in the improvement of industrial skills for professors and an increase in industrial based research for the university. The SiF feeder model meets its demand of public policy in supporting a skilled workforce for the industry, which could be an effective tool for the triple helix educational model of Thailand.

  1. Computational fluid dynamics analysis for flow accelerated corrosion in CANDU6 feeder pipes

    International Nuclear Information System (INIS)

    Catana, A.; Pauna, E.; Ioan, M.

    2013-01-01

    CANDU6 plant management over a long time period includes various ageing and degradation mechanisms like FAC manifested mainly at first and second elbow of CANDU6 outlet feeders. FAC take place at all CANDU6 built before 2000 year with feeders made from SA106 grade B low alloy carbon-steel (with chromium at 0.02%). CFD method is used in this paper to investigate the feeder's wall thinning process taking place mainly due local flow conditions in complex 3D geometrical configurations. The 380 outlet feeders grouped in 2.5'' (320) and 2.0'' feeders (60). The objective of this paper is to help, as much as possible, to focus investigation on most probable maximum thinning rate locations through 3D distribution of some TH parameters. Application of CFD methods in CANDU6 nuclear reactors implies the knowledge of real plant operating data like: long term time averaged channel power and mass flow as well as temperature, pressure, pHa etc allowing the optimization and cost reduction of wall thinning monitoring process at CANDU6 nuclear power plants. (authors)

  2. Network Reduction Algorithm for Developing Distribution Feeders for Real-Time Simulators: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Nagarajan, Adarsh; Nelson, Austin; Prabakar, Kumaraguru; Hoke, Andy; Asano, Marc; Ueda, Reid; Nepal, Shaili

    2017-06-15

    As advanced grid-support functions (AGF) become more widely used in grid-connected photovoltaic (PV) inverters, utilities are increasingly interested in their impacts when implemented in the field. These effects can be understood by modeling feeders in real-time systems and testing PV inverters using power hardware-in-the-loop (PHIL) techniques. This paper presents a novel feeder model reduction algorithm using a Monte Carlo method that enables large feeders to be solved and operated on real-time computing platforms. Two Hawaiian Electric feeder models in Synergi Electric's load flow software were converted to reduced order models in OpenDSS, and subsequently implemented in the OPAL-RT real-time digital testing platform. Smart PV inverters were added to the real-time model with AGF responses modeled after characterizing commercially available hardware inverters. Finally, hardware inverters were tested in conjunction with the real-time model using PHIL techniques so that the effects of AGFs on the choice feeders could be analyzed.

  3. On the Classification of Low Voltage Feeders for Network Planning and Hosting Capacity Studies

    Directory of Open Access Journals (Sweden)

    Benoît Bletterie

    2018-03-01

    Full Text Available The integration of large amounts of generation into distribution networks faces some limitations. By deploying reactive power-based voltage control concepts (e.g., volt/var control with distributed generators, the voltage rise caused by generators can be partly mitigated. As a result, the network hosting capacity can be accordingly increased, and costly network reinforcement might be avoided or postponed. This works however only for voltage-constrained feeders (opposed to current-constrained feeders. Due to the low level of monitoring in low voltage networks, it is important to be able to classify feeders according to the expected constraint in order to avoid the overloading risk. The main purpose of this paper is to investigate to which extent it is possible to predict the hosting capacity constraint (voltage or current of low voltage feeders on the basis of a large network data set. Two machine-learning techniques have been implemented and compared: clustering (unsupervised and classification (supervised. The results show that the general performance of the classification or clustering algorithms might be considered as rather poor at a first glance, reflecting the diversity of real low voltage feeders. However, a detailed analysis shows that the benefit of the classification is significant.

  4. Strong Electroweak Symmetry Breaking

    CERN Document Server

    Grinstein, Benjamin

    2011-01-01

    Models of spontaneous breaking of electroweak symmetry by a strong interaction do not have fine tuning/hierarchy problem. They are conceptually elegant and use the only mechanism of spontaneous breaking of a gauge symmetry that is known to occur in nature. The simplest model, minimal technicolor with extended technicolor interactions, is appealing because one can calculate by scaling up from QCD. But it is ruled out on many counts: inappropriately low quark and lepton masses (or excessive FCNC), bad electroweak data fits, light scalar and vector states, etc. However, nature may not choose the minimal model and then we are stuck: except possibly through lattice simulations, we are unable to compute and test the models. In the LHC era it therefore makes sense to abandon specific models (of strong EW breaking) and concentrate on generic features that may indicate discovery. The Technicolor Straw Man is not a model but a parametrized search strategy inspired by a remarkable generic feature of walking technicolor,...

  5. Electroweak symmetry breaking

    Energy Technology Data Exchange (ETDEWEB)

    Chanowitz, M.S.

    1990-09-01

    The Higgs mechanism is reviewed in its most general form, requiring the existence of a new symmetry-breaking force and associated particles, which need not however be Higgs bosons. The first lecture reviews the essential elements of the Higgs mechanism, which suffice to establish low energy theorems for the scattering of longitudinally polarized W and Z gauge bosons. An upper bound on the scale of the symmetry-breaking physics then follows from the low energy theorems and partial wave unitarity. The second lecture reviews particular models, with and without Higgs bosons, paying special attention to how the general features discussed in lecture 1 are realized in each model. The third lecture focuses on the experimental signals of strong WW scattering that can be observed at the SSC above 1 TeV in the WW subenergy, which will allow direct measurement of the strength of the symmetry-breaking force. 52 refs., 10 figs.

  6. Current redistribution and generation of kinetic energy in the stagnated Z pinch.

    Science.gov (United States)

    Ivanov, V V; Anderson, A A; Papp, D; Astanovitskiy, A L; Talbot, B R; Chittenden, J P; Niasse, N

    2013-07-01

    The structure of magnetic fields was investigated in stagnated wire-array Z pinches using a Faraday rotation diagnostic at the wavelength of 266 nm. The distribution of current in the pinch and trailing material was reconstructed. A significant part of current can switch from the main pinch to the trailing plasma preheated by x-ray radiation of the pinch. Secondary implosions of trailing plasma generate kinetic energy and provide enhanced heating and radiation of plasma at stagnation. Hot spots in wire-array Z pinches also provide enhanced radiation of the Z pinch. A collapse of a single hot spot radiates 1%-3% of x-ray energy of the Z pinch with a total contribution of hot spots of 10%-30%.

  7. Modeling of Aerobrake Ballute Stagnation Point Temperature and Heat Transfer to Inflation Gas

    Science.gov (United States)

    Bahrami, Parviz A.

    2012-01-01

    A trailing Ballute drag device concept for spacecraft aerocapture is considered. A thermal model for calculation of the Ballute membrane temperature and the inflation gas temperature is developed. An algorithm capturing the most salient features of the concept is implemented. In conjunction with the thermal model, trajectory calculations for two candidate missions, Titan Explorer and Neptune Orbiter missions, are used to estimate the stagnation point temperature and the inflation gas temperature. Radiation from both sides of the membrane at the stagnation point and conduction to the inflating gas is included. The results showed that the radiation from the membrane and to a much lesser extent conduction to the inflating gas, are likely to be the controlling heat transfer mechanisms and that the increase in gas temperature due to aerodynamic heating is of secondary importance.

  8. On two special values of temperature factor in hypersonic flow stagnation point

    Science.gov (United States)

    Bilchenko, G. G.; Bilchenko, N. G.

    2018-03-01

    The hypersonic aircraft permeable cylindrical and spherical surfaces laminar boundary layer heat and mass transfer control mathematical model properties are investigated. The nonlinear algebraic equations systems are obtained for two special values of temperature factor in the hypersonic flow stagnation point. The mappings bijectivity between heat and mass transfer local parameters and controls is established. The computation experiments results are presented: the domains of allowed values “heat-friction” are obtained.

  9. Bulk damping of sound in superfluid 3He--4He under stagnation of the normal component

    International Nuclear Information System (INIS)

    Karchava, T.A.; Sanikidze, D.G.; Chkhaidze, N.D.

    1983-01-01

    The propagation of waves in superfluid 3 He-- 4 He solutions is considered under partial stagnation of the normal component. The wave processes in capillaries are presented as a superposition of the first sound, second sound, and viscous and diffusion waves. The damping coefficients are calculated for the modified first sound and for the thermal wave in superfluid 3 He-- 4 He solutions and related to the viscosity, thermal conductivity, diffusion, barodiffusion, and thermodiffusion coefficients

  10. A probabilistic degradation model for the estimation of the remaining life distribution of feeders

    International Nuclear Information System (INIS)

    Yuan, X.-X.; Pandey, M.D.; Bickel, G.A.

    2006-01-01

    Wall thinning due to flow accelerated corrosion (FAC) is a pervasive form of degradation in the outlet feeder pipes of the primary heat transport system of CANDU reactors. The prediction of the end-of-life of a feeder from wall thickness measurement data is confounded by the sampling and temporal uncertainties associated with the FAC degradation phenomenon. Traditional regression-based statistical methods deal with only the sampling uncertainties, leaving the temporal uncertainties unresolved. This paper presents an advanced probabilistic model, which is able to integrate the temporal uncertainties into the prediction of lifetime. In particular, a random gamma process model is proposed to model the FAC process and it is calibrated with a set of wall thickness measurements using the method of maximum likelihood. This information can be used to establish an optimum strategy for inspection and replacement of feeders. (author)

  11. CAD/CAM DESIGN AND GENETIC OPTIMIZATION OF FEEDERS FOR SAND CASTING PROCESS

    Directory of Open Access Journals (Sweden)

    Nedeljko Dučić

    2016-08-01

    Full Text Available The paper proposes methodology of feeder design and optimization for sand casting process. Casting part is a part of excavator buckets, i.e. holder of the cutting tooth. Process of design and optimization is based on the application of the rules, which are the result of many years of work researchers in the field of metal casting. Computer Aided Design (CAD is used as a methodology in the design of feeders. Genetic Algorithm (GA as an artificial intelligence technique is used in the optimization process of the feeder geometry. Computer Aided Manufacturing (CAM is used as methodology that involves numerical simulation of the casting process. Numerical simulation is used to verify the validity of the optimized geometry of the feeding system.

  12. Conspray dynamic sleeve piston coal feeder. Phase II. Verification tests. Final technical report

    Energy Technology Data Exchange (ETDEWEB)

    1984-01-26

    This report details the performance of Phase II: Verification Tests of the Conspray dynamic sleeve piston coal feeder. The machine performed for 200 hours at 700 psi backpressure, utilizing a 70% to 200 mesh Utah bituminous coal as feedstock. All test work was satisfactorily completed. A post-test inspection was performed. A report of component wear and failures incurred in testing is included as well as suggestions for machine upgrades. The overall conclusion is that the dynamic sleeve piston feeder has proven its ability to operate safely and reliably. When problems have occurred, the machine has demonstrated inherent safety by shutting down without endangering process or personnel. With the recommended improvements incorporated into the feeder, the unit will be ready for installation on a pilot scale coal gasifier. 9 figures, 11 tables.

  13. Convex relaxation of Optimal Power Flow in Distribution Feeders with embedded solar power

    DEFF Research Database (Denmark)

    Hermann, Alexander Niels August; Wu, Qiuwei; Huang, Shaojun

    2016-01-01

    There is an increasing interest in using Distributed Energy Resources (DER) directly coupled to end user distribution feeders. This poses an array of challenges because most of today’s distribution feeders are designed for unidirectional power flow. Therefore when installing DERs such as solar...... panels with uncontrolled inverters, the upper limit of installable capacity is quickly reached in many of today’s distribution feeders. This problem can often be mitigated by optimally controlling the voltage angles of inverters. However, the optimal power flow problem in its standard form is a large...... scale non-convex optimization problem, and thus can’t be solved precisely and also is computationally heavy and intractable for large systems. This paper examines the use of a convex relaxation using Semi-definite programming to optimally control solar power inverters in a distribution grid in order...

  14. Study of atmospheric stagnation, recirculation, and ventilation potential at Narora Atomic Power Station site

    International Nuclear Information System (INIS)

    Kumar, Deepak; Kumar, Avinash; Kumar, Vimal; Rao, K.S.; Kumar, Jaivender; Ravi, P.M.

    2011-01-01

    Atmosphere is an important pathway to be considered in assessment of the environmental impact of radioactivity releases from nuclear facilities. Estimation of concentration of released effluents in air and possible ground contamination needs an understanding of relevant atmospheric dispersion. This article describes the meteorological characteristics of Narora Atomic Power Station (NAPS) site by using the integral parameters developed by Allwine and Whiteman. Meteorological data measured during the period 2006-2010 were analyzed. The integral quantities related to the occurrence of stagnation, recirculation, and ventilation characteristics were studied for NAPS site to assess the dilution potential of the atmosphere. Wind run and recirculation factors were calculated for a 24-h transport time using 5 years of hourly surface measurements of wind speed and direction. The occurrence of stagnation, recirculation, and ventilation characteristics during 2006-2010 at NAPS site is observed to be 33.8% of the time, 19.5% of the time, and 34.7% of the time, respectively. The presence of strong winds with predominant wind direction NW and WNW during winter and summer seasons leads to higher ventilation (48.1% and 44.3%) and recirculation (32.6% of the summer season). The presence of light winds and more dispersed winds during prewinter season with predominant wind directions W and WNW results in more stagnation (59.7% of the prewinter season). Thus, this study will serve as an essential meteorological tool to understand the transport mechanism of atmospheric radioactive effluent releases from any nuclear industry. (author)

  15. Colloid retention in porous media: mechanistic confirmation of wedging and retention in zones of flow stagnation.

    Science.gov (United States)

    Johnson, W P; Li, Xiqing; Yal, Gozde

    2007-02-15

    A three-dimensional particle tracking model for colloid transport in porous media was developed that predicts colloid retention in porous media in the presence of an energy barrier via two mechanisms: (1) wedging of colloids within grain to grain contacts; (2) retention of colloids (without attachment) in flow stagnation zones. The model integrates forces experienced by colloids during transport in porous media, i.e., fluid drag, gravity, diffusion, and colloid-surface Derjaguin-Landau-Verwey-Overbeek interactions. The model was implemented for a fluid flow field that explicitly represented grain to grain contacts. The model utilized a variable time stepping routine to allow finer time steps in zones of rapid change in fluid velocity and colloid-surface interaction forces. Wedging was favored by colloid: collector ratios greater than about 0.005, with this threshold ratio increasing with decreasing fluid velocity. Retention in flow stagnation zones was demonstrated for colloid: collector ratios less than about 0.005, with this threshold decreasing with increasing fluid velocity. Both wedging and retention in flow stagnation zones were sensitive to colloid-surface interaction forces (energy barrier height and secondary energy minimum depth). The model provides a mechanistic basis for colloid retention in the presence of an energy barrier via processes that were recently hypothesized to explain experimental observations.

  16. Impact of Distribution Feeders that do not have Voltage Regulators on the number of Charged Electric Vehicles using IEEE 34 Bus Test Feeder

    Energy Technology Data Exchange (ETDEWEB)

    Allehyani, Ahmed [University of Southern California, Department of Electrical Engineering; Beshir, Mohammed [University of Southern California, Department of Electrical Engineering

    2015-02-01

    Voltage regulators help maintain an acceptable voltage profile for the system. This paper discusses the effect of installing voltage regulators to the system to fix the voltage drop resulting from the electrical vehicles loading increase when they are being charged. The effect will be studied in the afternoon, when the peak load occurs, using the IEEE 34 bus test feeder. First, only one spot node is used to charge the electric vehicles while a voltage regulator is present. Second, five spot nodes are loaded at the same time to charge the electric vehicles while voltage regulators are installed at each node. After that, the impact of electric vehicles on distribution feeders that do not have voltage regulators will appear.

  17. Breaking the Waves

    DEFF Research Database (Denmark)

    Christensen, Poul Rind; Kirketerp, Anne

    2006-01-01

    The paper shortly reveals the history of a small school - the KaosPilots - dedicated to educate young people to carriers as entrepreneurs. In this contribution we want to explore how the KaosPilots managed to break the waves of institutionalised concepts and practices of teaching entrepreneurship...... pedagogical elements on which the education in entrepreneurship rests....

  18. Model Breaking Points Conceptualized

    Science.gov (United States)

    Vig, Rozy; Murray, Eileen; Star, Jon R.

    2014-01-01

    Current curriculum initiatives (e.g., National Governors Association Center for Best Practices and Council of Chief State School Officers 2010) advocate that models be used in the mathematics classroom. However, despite their apparent promise, there comes a point when models break, a point in the mathematical problem space where the model cannot,…

  19. Effect of artificial feeders on pollen loads of the hummingbirds of Cerro de La Muerte, Costa Rica

    Directory of Open Access Journals (Sweden)

    Gerardo Avalos

    2012-03-01

    Full Text Available Although sugar-water feeders are commonly used by enthusiasts to attract hummingbirds, little is known about how they affect hummingbird behavior and flower use. We studied the highland hummingbird assemblage of Cerro de La Muerte, Costa Rica, both at a site with permanent feeders (La Georgina Restaurant and further from it. We examined how feeder use and monopolization affected seasonal changes in pollen loads during four sampling periods, including dry and wet seasons, from 2003-2005. We expected that species monopolizing the feeders would carry little or no pollen whatsoever, and would have pollen loads characterized by low floral diversity, in contrast with species less dependent on feeders. We obtained pollen samples from 183 individuals of four hummingbird species captured around the feeders using mist nets, which were compared with a pollen reference collection of plants with a pollination syndrome by hummingbirds. The same methods were implemented at a site 3km away from the feeders. Feeder usage was quantified by counting the number of times hummingbirds drank from the feeders in periods of 4min separated by 1min. The effects of hummingbird species and season on pollen load categories were assessed using a nominal logistic regression. The alpha species at the site, the Fiery-throated Hummingbird (Panterpe insignis, dominated the feeders during the dry season. Meanwhile, in the wet season, feeder usage was more evenly distributed across species, with the exception of the Volcano Hummingbird, Selasphorus flammula, which occupies the last place in the dominance hierarchy. Pollen loads of hummingbirds captured near feeders were low in abundance (more than 50% of captured individuals had zero or low pollen loads, and low in species richness (96% of the hummingbirds with pollen from only one plant genus, Centropogon. Overall pollen loads increased during the dry season coinciding with peaks in flower availability, although the majority of

  20. Effect of artificial feeders on pollen loads of the hummingbirds of Cerro de la Muerte, Costa Rica.

    Science.gov (United States)

    Avalos, Gerardo; Soto, Alejandra; Alfaro, Willy

    2012-03-01

    Although sugar-water feeders are commonly used by enthusiasts to attract hummingbirds, little is known about how they affect hummingbird behavior and flower use. We studied the highland hummingbird assemblage of Cerro de La Muerte, Costa Rica, both at a site with permanent feeders (La Georgina Restaurant) and further from it. We examined how feeder use and monopolization affected seasonal changes in pollen loads during four sampling periods, including dry and wet seasons, from 2003-2005. We expected that species monopolizing the feeders would carry little or no pollen whatsoever, and would have pollen loads characterized by low floral diversity, in contrast with species less dependent on feeders. We obtained pollen samples from 183 individuals of four hummingbird species captured around the feeders using mist nets, which were compared with a pollen reference collection of plants with a pollination syndrome by hummingbirds. The same methods were implemented at a site 3km away from the feeders. Feeder usage was quantified by counting the number of times hummingbirds drank from the feeders in periods of 4min separated by 1min. The effects of hummingbird species and season on pollen load categories were assessed using a nominal logistic regression. The alpha species at the site, the Fiery-throated Hummingbird (Panterpe insignis), dominated the feeders during the dry season. Meanwhile, in the wet season, feeder usage was more evenly distributed across species, with the exception of the Volcano Hummingbird, Selasphorus flammula, which occupies the last place in the dominance hierarchy. Pollen loads of hummingbirds captured near feeders were low in abundance (more than 50% of captured individuals had zero or low pollen loads), and low in species richness (96% of the hummingbirds with pollen from only one plant genus, Centropogon). Overall pollen loads increased during the dry season coinciding with peaks in flower availability, although the majority of captured

  1. Methods for Dynamic Analysis of Distribution Feeders with High Penetration of PV Generators

    Energy Technology Data Exchange (ETDEWEB)

    Nagarajan, Adarsh; Ayyanar, Raja

    2016-11-21

    An increase in the number of inverter-interfaced photovoltaic (PV) generators on existing distribution feeders affects the design, operation, and control of the distribution systems. Existing distribution system analysis tools are capable of supporting only snapshot and quasi-static analyses. Capturing the dynamic effects of PV generators during the variation in distribution system states is necessary when studying the effects of controller bandwidths, multiple voltage correction devices, and anti-islanding. This work explores the use of dynamic phasors and differential algebraic equations (DAE) for impact analysis of PV generators on the existing distribution feeders.

  2. Consideration and research of high voltage insulation strategy for ITER Feeder busbar joint

    International Nuclear Information System (INIS)

    Huang, Xiongyi; Song, Yuntao; Zheng, Jinxing; Yu, Xiaowu; Xiao, Weiwu; Gao, Daming; Tao, Yuming; Wang, Chunyu; Gung, Chen-yu; Clayton, Nicholas; Niu, Erwu; Chen, Yonghua; Mitcell, Neil

    2013-01-01

    Highlights: • Several rounds insulation trials for ITER Feeder joint were carried out in ASIPP. • Wet-winding, VPI were practiced and attempt for the best impregnation strategy. • Improvement of wet-winding technology with vacuum assistance was realized. • To supplement the electrical test, DR technology was explored for insulation quality inspection. -- Abstract: The ITER Feeder busbar joint is an important component which connects different sections of busbar which run from the high temperature superconducting current leads to the magnet terminals. High voltage insulated bus bar sections will be assembled onto the feeder support structure (called the containment duct), and the joints between sections will be made in situ. The high voltage insulation over the joint is the final step to complete the insulation of the whole bus bar system, and its quality is key to achieving the required electrical performance of the system. The final joint has a complex external configuration with an irregular structure in places, which makes it difficult for the application of the insulation. The limited access in the Feeder and the complex joint external structure make the implementation of the joint insulation hard to solve. The Feeder group at ASIPP has carried out significant R and D for the joint insulation, involving research on the selection of materials, the design of the insulation structure, the curing technology and the quality inspection method. After many rounds of manufacturing and testing, the insulation strategy for the Feeder joint will focus on the so-called “wet-winding” technology. Despite the fact that this process has some intrinsic disadvantages, it is more appropriate for the joint structure compared to other methods. The sub-suppliers to ASIPP have chosen this impregnation method for the feeder qualification activities based on guidance from ASIPP. This paper describes the research procedure of the ITER Feeder busbar joint insulation

  3. Methods to Determine Recommended Feeder-Wide Advanced Inverter Settings for Improving Distribution System Performance

    Energy Technology Data Exchange (ETDEWEB)

    Rylander, Matthew; Reno, Matthew J.; Quiroz, Jimmy E.; Ding, Fei; Li, Huijuan; Broderick, Robert J.; Mather, Barry; Smith, Jeff

    2016-11-21

    This paper describes methods that a distribution engineer could use to determine advanced inverter settings to improve distribution system performance. These settings are for fixed power factor, volt-var, and volt-watt functionality. Depending on the level of detail that is desired, different methods are proposed to determine single settings applicable for all advanced inverters on a feeder or unique settings for each individual inverter. Seven distinctly different utility distribution feeders are analyzed to simulate the potential benefit in terms of hosting capacity, system losses, and reactive power attained with each method to determine the advanced inverter settings.

  4. The Role of Rumination and Stressful Life Events in the Relationship between the Qi Stagnation Constitution and Depression in Women: A Moderated Mediation Model

    Directory of Open Access Journals (Sweden)

    Mingfan Liu

    2017-01-01

    Full Text Available The qi stagnation constitution is associated with depression in traditional Chinese medicine. It is unclear how rumination and stressful life events affect the relationship between the qi stagnation constitution and depression. The Qi Stagnation Constitution Scale, Ruminative Response Scale, Center for Epidemiologic Studies Depression Scale, and Adolescent Self-Rating Life Events Checklist were used to assess this association in 1200 female college students. The results revealed that the qi stagnation constitution was positively associated with depression. Furthermore, rumination was a partial mediator of the relationship between the qi stagnation constitution and depression. In addition, stressful life events moderated the direct effect and mediating effect of the qi stagnation constitution on depression. These findings indicate that rumination and stressful life events may affect the relationship between the qi stagnation constitution and depression in women.

  5. 7 CFR 1230.113 - Collection and remittance of assessments for the sale of feeder pigs and market hogs.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 10 2010-01-01 2010-01-01 false Collection and remittance of assessments for the sale of feeder pigs and market hogs. 1230.113 Section 1230.113 Agriculture Regulations of the Department... pigs and market hogs. Pursuant to the provisions of § 1230.71, purchasers of feeder pigs or market hogs...

  6. Breaking News as Radicalisation

    DEFF Research Database (Denmark)

    Hartley, Jannie Møller

    provides us with the following two research questions: How does the category of breaking news fit into Tuchmans typology related to time, planning and technology? What types of stories are providing journalistic capital and how are online news stories categorised relatively within the journalistic field?......The aim of the paper is to make explicit how the different categories are applied in the online newsroom and thus how new categories can be seen as positioning strategies in the form of radicalisations of already existing categories. Thus field theory provides us with tools to analyse how online...... journalists are using the categorisations to create hierarchies within the journalistic field in order to position themselves as specialists in what Tuchman has called developing news, aiming and striving for what today is know as breaking news and the “exclusive scoop,” as the trademark of online journalism...

  7. Co-ordination of directional overcurrent protection with load current for parallel feeders

    Energy Technology Data Exchange (ETDEWEB)

    Wright, J.W.; Lloyd, G.; Hindle, P.J. [Alstom, Inc., Stafford (United Kingdom). T and D Protection and Control

    1999-11-01

    Directional phase overcurrent relays are commonly applied at the receiving ends of parallel feeders or transformer feeders. Their purpose is to ensure full discrimination of main or back-up power system overcurrent protection for a fault near the receiving end of one feeder. This paper reviews this type of relay application and highlights load current setting constraints for directional protection. Such constraints have not previously been publicized in well-known text books. A directional relay current setting constraint that is suggested in some text books is based purely on thermal rating considerations for older technology relays. This constraint may not exist with modern numerical relays. In the absence of any apparent constraint, there is a temptation to adopt lower current settings with modern directional relays in relation to reverse load current at the receiving ends of parallel feeders. This paper identifies the danger of adopting very low current settings without any special relay feature to ensure protection security with load current during power system faults. A system incident recorded by numerical relays is also offered to highlight this danger. In cases where there is a need to infringe the identified constraints an implemented and testing relaying technique is proposed.

  8. Feeder Cell Type Affects the Growth of In Vitro Cultured Bovine Trophoblast Cells

    Directory of Open Access Journals (Sweden)

    Islam M. Saadeldin

    2017-01-01

    Full Text Available Trophectoderm cells are the foremost embryonic cells to differentiate with prospective stem-cell properties. In the current study, we aimed at improving the current approach for trophoblast culture by using granulosa cells as feeders. Porcine granulosa cells (PGCs compared to the conventional mouse embryonic fibroblasts (MEFs were used to grow trophectoderm cells from hatched bovine blastocysts. Isolated trophectoderm cells were monitored and displayed characteristic epithelial/cuboidal morphology. The isolated trophectoderm cells expressed mRNA of homeobox protein (CDX2, cytokeratin-8 (KRT8, and interferon tau (IFNT. The expression level was higher on PGCs compared to MEFs throughout the study. In addition, primary trophectoderm cell colonies grew faster on PGCs, with a doubling time of approximately 48 hrs, compared to MEFs. PGCs feeders produced a fair amount of 17β-estradiol and progesterone. We speculated that the supplementation of sex steroids and still-unknown factors during the trophoblasts coculture on PGCs have helped to have better trophectoderm cell’s growth than on MEFs. This is the first time to use PGCs as feeders to culture trophectoderm cells and it proved superior to MEFs. We propose PGCs as alternative feeders for long-term culture of bovine trophectoderm cells. This model will potentially benefit studies on the early trophoblast and embryonic development in bovines.

  9. The Use of Filter-feeders to Manage Disease in a Changing World

    NARCIS (Netherlands)

    Burge, C.A.; Closek, C.J.; Friedman, C.S.; Groner, M.; Jenkins, C.M.; Shore-Maggio, A.; Welsh, J.E.

    2016-01-01

    Rapid environmental change is linked to increases in aquatic disease heightening the need to develop strategies to manage disease. Filter-feeding species are effective biofilters and can naturally mitigate disease risk to humans and wildlife. We review the role of filter-feeders, with an emphasis on

  10. Systems Operation Studies for Automated Guideway Transit Systems: Feeder Systems Model Functional Specification

    Science.gov (United States)

    1981-01-01

    This document specifies the functional requirements for the AGT-SOS Feeder Systems Model (FSM), the type of hardware required, and the modeling techniques employed by the FSM. The objective of the FSM is to map the zone-to-zone transit patronage dema...

  11. Optimal Design of the Feeder-Bus Network Based on the Transfer System

    Directory of Open Access Journals (Sweden)

    Lianbo Deng

    2013-01-01

    Full Text Available This paper studied the classic feeder-bus network design problem (FBNDP, which can be described as follows: for the passenger travel demand between rail stations and bus stops on a given urban transit network, it designs the optimal feeder bus routes and frequencies so as to minimize the passengers’ travel expense and the operator’s cost. We extended the demand pattern of M-to-1 in most existing researches to M-to-M. We comprehensively considered the passenger travel cost, which includes the waiting and riding cost on the bus, riding cost on rail, and transfer cost between these two transportation modes, and presented a new genetic algorithm that determines the optimal feeder-bus operating frequencies under strict constraint conditions. The numerical examples under different demand patterns have been experienced and analysed, which showed the robustness and efficiency of the presented algorithm. We also found that the distribution pattern of the travel demand has a significant influence on the feeder-bus network construction.

  12. The effect of stocking density and bin feeder space on performance ...

    African Journals Online (AJOL)

    The effect of stocking density and bin feeder space on performance in pigs. G.A. Lavers, N.S. Ferguson. Abstract. (South African J of Animal Science, 2000, 30, Supplement 1: 70-71). Full Text: EMAIL FREE FULL TEXT EMAIL FREE FULL TEXT · DOWNLOAD FULL TEXT DOWNLOAD FULL TEXT.

  13. The effect of stocking density and bin feeder space on performance ...

    African Journals Online (AJOL)

    Unknown

    The effect of stocking density and bin feeder space on performance in pigs. G.A. Lavers# and N.S. Ferguson. School of Agricultural Sciences & Agribusiness, University of Natal, P Bag X01, Scottsville 3209. #Email: lavers@agric.unp.ac.za. Introduction. Pigs housed individually have been shown to have higher feed intakes ...

  14. Effects of an increasing filter feeder stock on larval abundance in the Oosterschelde estuary (SW Netherlands)

    NARCIS (Netherlands)

    Troost, Karin; Gelderman, Edzard; Kamermans, Pauline; Smaal, Aad C.; Wolff, Wim J.

    Predation by adult bivalves oil bivalve larvae has been suggested to reduce larval abundance in areas with high bivalve filter-feeder biomass. Although the occurrence of larviphagy is well-studied in the laboratory, its effects in the field have scarcely been studied. We studied larviphagy at

  15. Effects of an increasing filter feeder stock on larval abundance in the Oosterschelde estuary (SW Netherlands)

    NARCIS (Netherlands)

    Troost, K.; Gelderman, E.A.C.; Kamermans, P.; Smaal, A.C.; Wolff, W.

    2009-01-01

    Predation by adult bivalves on bivalve larvae has been suggested to reduce larval abundance in areas with high bivalve filter-feeder biomass. Although the occurrence of larviphagy is well-studied in the laboratory, its effects in the field have scarcely been studied. We studied larviphagy at

  16. EV Charging Facilities and Their Application in LV Feeders with Photovoltaics

    DEFF Research Database (Denmark)

    Marra, Francesco; Yang, Guangya; Træholt, Chresten

    2013-01-01

    Low-voltage (LV) grid feeders with high penetration of photovoltaics (PVs) are often affected by voltage magnitude problems. To solve such issues, previous research has shown that reactive power methods, active power curtailment and grid reinforcement can be used for voltage support, yet showing...

  17. Improvement of Local Voltage in Feeders with Photovoltaic using Electric Vehicles

    DEFF Research Database (Denmark)

    Marra, Francesco; Yang, Guangya; Fawzy, Y. T.

    2013-01-01

    In low-voltage (LV) feeders with high penetration of photovoltaic (PV), a major issue to be solved is voltage rise due to the active power injection. If no measures are taken, this may lead to generation’s interruptions and to the malfunctioning of domestic appliances due to non-standard voltage...

  18. 46 CFR 113.25-8 - Distribution of general emergency alarm system feeders and branch circuits.

    Science.gov (United States)

    2010-10-01

    ... main vertical fire bulkheads, the general emergency alarm system must be arranged into vertical service... 46 Shipping 4 2010-10-01 2010-10-01 false Distribution of general emergency alarm system feeders... (CONTINUED) ELECTRICAL ENGINEERING COMMUNICATION AND ALARM SYSTEMS AND EQUIPMENT General Emergency Alarm...

  19. Tits recognize the potential dangers of predators and harmless birds in feeder experiments

    Czech Academy of Sciences Publication Activity Database

    Tvardíková, Kateřina; Fuchs, R.

    2012-01-01

    Roč. 30, č. 1 (2012), s. 157-165 ISSN 0289-0771 Grant - others:AV ČR(CZ) IAA601410803 Institutional research plan: CEZ:AV0Z50070508 Keywords : feeders * predator recognition * risk Subject RIV: EH - Ecology, Behaviour Impact factor: 1.000, year: 2012 http://www.springerlink.com/content/2338033t30261604/fulltext.pdf

  20. Feasibility study of modern airships, phase 2. Volume 2: Airport feeder vehicle

    Science.gov (United States)

    1976-01-01

    The Airport Feeder vehicle is a VTOL, semi-buoyant ellipsoidal airship capable of transporting passengers or cargo to major CTOL hub terminals from suburban and downtown depots. Six tasks were reviewed: (1) vehicle design definition, (2) operational procedures analysis, (3) cost analysis, (4) comparison with alternate transportation modes, (5) mission/vehicle feasibility assessment, and (6) technology assessment.

  1. Production capacity of estuarine ecosystems and filter feeder stock size: indices for under- or overgrazing

    NARCIS (Netherlands)

    Smaal, A.C.

    2012-01-01

    For extensive shellfish culture, the trophic capacity of the culture system is a major production factor and this is determined by the primary production, the flux of food to the culture sites and the role of competing filter feeders. Various control mechanisms play a role in these processes:

  2. Routinizing Breaking News

    DEFF Research Database (Denmark)

    Hartley, Jannie Møller

    2011-01-01

    This chapter revisits seminal theoretical categorizations of news proposed three decades earlier by US sociologist Gaye Tuchman. By exploring the definition of ”breaking news” in the contemporary online newsrooms of three Danish news organisations, the author offers us a long overdue re......-theorization of journalistic practice in the online context and helpfully explores well-evidenced limitations to online news production, such as the relationship between original reporting and the use of ”shovelware.”...

  3. Mass transfer effects in feeder flow-accelerated corrosion wall thinning

    International Nuclear Information System (INIS)

    Pietralik, J.

    2008-01-01

    Flow conditions play a dominant role in Flow-Accelerated Corrosion (FAC) under certain conditions, e.g., in CANDU feeders. While chemistry and materials set the overall potential for FAC, flow conditions determine the local distribution of wall thinning. Recent plant data of feeders and laboratory tests confirms that there is a close relationship between local flow conditions, expressed by mass transfer coefficient, and FAC rate in CANDU feeder bends. The knowledge of local effects can be useful for minimizing the number of inspected components, predicting the location of the highest FAC rate for a given piping component, and determining what components or feeders should be replaced. A similar evaluation applies also to FAC in heat transfer equipment such as heat exchangers and steam generators. The objective of this paper is to examine the relationship between FAC rate and local mass transfer parameters. For FAC where the flow is dominant, the FAC rate is proportional to mass flux of ferrous ions. The mass flux is the product of the mass transfer coefficient and the concentration difference, or degree of saturation. The mass transfer coefficient describes the intensity of the transport of corrosion products (ferrous ions) from the oxide-water interface into the bulk water. Therefore, this parameter can be used for predicting the local distribution of FAC rate in the mass-transfer controlled FAC. The degree of saturation reduces the mass flux, thus reducing the FAC rate. This effect can be significant in long piping, e.g., in outlet feeders. The paper presents plant and laboratory evidence for the relationship between local mass transfer conditions and the FAC rate. It shows correlations for mass transfer coefficient in components that are highly susceptible to FAC and most important flow parameters that affect mass transfer coefficient. The role of surface roughness, wall shear stress, and local turbulence is also discussed. (author)

  4. The Use of Filter-feeders to Manage Disease in a Changing World.

    Science.gov (United States)

    Burge, Colleen A; Closek, Collin J; Friedman, Carolyn S; Groner, Maya L; Jenkins, Cody M; Shore-Maggio, Amanda; Welsh, Jennifer E

    2016-10-01

    Rapid environmental change is linked to increases in aquatic disease heightening the need to develop strategies to manage disease. Filter-feeding species are effective biofilters and can naturally mitigate disease risk to humans and wildlife. We review the role of filter-feeders, with an emphasis on bivalves, in altering disease outcomes via augmentation and reduction. Filtration can reduce transmission by removing pathogens from the water column via degradation and release of pathogens in pseudofeces. In other cases, filtration can increase pathogen transmission and disease risk. The effect of filtration on pathogen transmission depends on the selectivity of the filter-feeder, the degree of infectivity by the pathogen, the mechanism(s) of pathogen transmission and the ability of the pathogen to resist degradation. For example, some bacteria and viruses can resist degradation and accumulate within a filter-feeder leading to disease transmission to humans and other wildlife upon ingestion. Since bivalves can concentrate microorganisms, they are also useful as sentinels for the presence of pathogenic microorganisms. While somewhat less studied, other invertebrates, including ascidians and sponges may also provide ecosystem services by altering pathogen transmission. In all scenarios, climate change may affect the potential for filter-feeders to mitigate disease risk. We conclude that an assessment including empirical data and modeling of system-wide impacts should be conducted before selection of filter-feeders to mitigate disease. Such studies should consider physiology of the host and microbe and risk factors for negative impacts including augmentation of other pathogens. © The Author 2016. Published by Oxford University Press on behalf of the Society for Integrative and Comparative Biology. All rights reserved. For permissions please email: journals.permissions@oup.com.

  5. Craft-Joule Project: Stagnation proof transparently insulated flat plate solar collector (static)

    Energy Technology Data Exchange (ETDEWEB)

    Oliva, A; Cadafalch, J; Perez-Segarra, C.D. [Universitat Politecnica de Catalunya, Barcelona (Spain)] (and others)

    2000-07-01

    The STATIC (STAgnation proof Transparently Insulated flat plate Solar Collector) project is a Craft-Joule Project within the framework of the Non Nuclear Energy Programme Joule III coordinated by the Centre Technologic de Transferencia de Calor (CTTC). The core group of SMEs involved in the project has its main economical activity in the field of solar thermal systems at low temperature level (domestic hot water, solar heating, etc.). Beyond this, a large application potential exists for solar heating at medium temperature level (from 80 to 160 Celsius degrees) : industrial process heat, solar cooling and air conditioning, solar drying , distillation and desalination. Three of the four SME proposers are located in Southern Europe and in the Caribean, where a continuos increase of the demand for air conditioning and cooling has been demonstrated in the last years. The recent development of flat plate solar collectors with honeycomb-type transparent insulation cover has shown that this type of collectors can become a low cost alternative to evacuated tube and high concentrating CPC collectors in the medium temperature range from 80 to 160 Celsius degrees. With the expected reduction of collector cost, that forms 30%-50% of total system cost, a decisive break-through of solar thermal systems using heat in the medium temperature range can be achieved. The feasibility and good performance of these solar collectors has been proved in several prototypes. Nevertheless, up to now no commercial products are available. In order to reach this, the following developments of new concepts are necessary and are being carried out within this project: solution of the problem of overheating: development of collector versions for different working temperatures: optimization of the design with the support of high level numerical simulation. Several prototypes of the new solar collectors are being tested. System tests will also be carried or for two test arrays of optimized collector

  6. Stagnation point flow towards nonlinear stretching surface with Cattaneo-Christov heat flux

    Science.gov (United States)

    Hayat, T.; Zubair, M.; Ayub, M.; Waqas, M.; Alsaedi, A.

    2016-10-01

    Here the influence of the non-Fourier heat flux in a two-dimensional (2D) stagnation point flow of Eyring-Powell liquid towards a nonlinear stretched surface is reported. The stretching surface is of variable thickness. Thermal conductivity of fluid is taken temperature-dependent. Ordinary differential systems are obtained through the implementation of meaningful transformations. The reduced non-dimensional expressions are solved for the convergent series solutions. Convergence interval is obtained for the computed solutions. Graphical results are displayed and analyzed in detail for the velocity, temperature and skin friction coefficient. The obtained results reveal that the temperature gradient enhances when the thermal relaxation parameter is increased.

  7. Stagnation-Point Flow towards a Stretching Vertical Sheet with Slip Effects

    Directory of Open Access Journals (Sweden)

    Khairy Zaimi

    2016-04-01

    Full Text Available The effects of partial slip on stagnation-point flow and heat transfer due to a stretching vertical sheet is investigated. Using a similarity transformation, the governing partial differential equations are reduced into a system of nonlinear ordinary differential equations. The resulting equations are solved numerically using a shooting method. The effect of slip and buoyancy parameters on the velocity, temperature, skin friction coefficient and the local Nusselt number are graphically presented and discussed. It is found that dual solutions exist in a certain range of slip and buoyancy parameters. The skin friction coefficient decreases while the Nusselt number increases as the slip parameter increases.

  8. Off-centered stagnation point flow of a couple stress fluid towards a rotating disk.

    Science.gov (United States)

    Khan, Najeeb Alam; Riaz, Fatima

    2014-01-01

    An investigation has been made to study the off-centered stagnation flow of a couple stress fluid over a rotating disk. The model developed for the governing problem in the form of partial differential equations has been converted to ordinary differential equations with the use of suitable similarity transformation. The analytical approximation has been made with the most promising analytical approach, homotopy analysis method (HAM). The convergence region of the obtained solution is determined and plotted. The effects of couple stress and nondimensional parameters have been observed on the flows of couple stress fluid. Also comparison has been made with the Newtonian fluid as the special case of considered problem.

  9. Characteristics of three dimensional stagnation point flow of Hybrid nanofluid past a circular cylinder

    Science.gov (United States)

    Nadeem, S.; Abbas, Nadeem; Khan, A. U.

    2018-03-01

    The characteristics of three-dimensional stagnation point flow of Hybrid nanofluid past a circular cylinder are explored. The fluid flow is entertained in the presence/absence of thermal slip effects. The flow model is controlled through the partial differential equations. Since these equations are highly non-linear in character. So for the order reduction a suitable set of transformation is used. The reduced system is solved by using shooting method. The obtained results are offered through graphs and tables. It is noticed that the heat transfer rate is high in Hybrid nanofluid as compared to nanofluid. The present work is validated by developing comprising with existing literature.

  10. Growth or stagnation in pre-industrial Britain? A revealed income growth approach

    DEFF Research Database (Denmark)

    Groth, Christian; Persson, Karl Gunnar

    2016-01-01

    The extent of growth in pre-industrial Europe in general and in Britain in particular has attracted intense scholarly focus. Growth or Malthusian stagnation? No consensus has evolved. Reconstructions of national income from 1300 and up to the Industrial Revolution come to opposing conclusions...... and so do econometric studies. Applying Engels’ law, we suggest a new approach in which income growth is revealed by changes in occupational structure. Data needed for this approach are less contested than the wage and output series used in the existing literature. We find that pre-industrial Britain...

  11. Real-Time Distribution Feeder Performance Monitoring, Advisory Control, and Health Management System

    Energy Technology Data Exchange (ETDEWEB)

    Stoupis, James; Mousavi, Mirrasoul

    2014-09-30

    New data collection system equipment was installed in Xcel Energy substations and data was collected from 6 substations and 20 feeders. During Phase I, ABB collected and analyzed 793 real-time events to date from 6 Xcel Energy substations and continues today. The development and integration of several applications was completed during the course of this project, including a model-based faulted segment identification algorithm, with very positive results validated with field-gathered data discussed and included in this report. For mostly underground feeders, the success rate is 90% and the overreach rate is 90%. For mostly overhead feeders, the success rate is 74% and the overreach rate is 50%. The developed method is producing very accurate results for mostly underground feeders. For mostly overhead feeders, due to the bad OMS data quality and varying fault resistance when arcing, the developed method is producing good results but with much room for improvement. One area where the algorithm can be improved is the accuracy for sub-cycle fault events. In these cases, the accuracy of the conventional signal processing methods suffers due to most of these methods being based on a one-cycle processing window. By improving the signal processing accuracy, the accuracy of the faulted segment identification algorithm will also improve significantly. ABB intends to devote research in this area in the near future to help solve this problem. Other new applications developed during the course of the project include volt/VAR monitoring, unbalanced capacitor switching detection, unbalanced feeder loading detection, and feeder overloading detection. An important aspect of the demonstration phase of the project is to show the ability to provide adequate “heads-up” time ahead of customer calls or AMI reports so that the operators are provided with the much needed time to collect information needed to address an outage. The advance notification feature of the demonstration system

  12. Compositional mantle layering revealed by slab stagnation at ~1000-km depth.

    Science.gov (United States)

    Ballmer, Maxim D; Schmerr, Nicholas C; Nakagawa, Takashi; Ritsema, Jeroen

    2015-12-01

    Improved constraints on lower-mantle composition are fundamental to understand the accretion, differentiation, and thermochemical evolution of our planet. Cosmochemical arguments indicate that lower-mantle rocks may be enriched in Si relative to upper-mantle pyrolite, whereas seismic tomography images suggest whole-mantle convection and hence appear to imply efficient mantle mixing. This study reconciles cosmochemical and geophysical constraints using the stagnation of some slab segments at ~1000-km depth as the key observation. Through numerical modeling of subduction, we show that lower-mantle enrichment in intrinsically dense basaltic lithologies can render slabs neutrally buoyant in the uppermost lower mantle. Slab stagnation (at depths of ~660 and ~1000 km) and unimpeded slab sinking to great depths can coexist if the basalt fraction is ~8% higher in the lower mantle than in the upper mantle, equivalent to a lower-mantle Mg/Si of ~1.18. Global-scale geodynamic models demonstrate that such a moderate compositional gradient across the mantle can persist can in the presence of whole-mantle convection.

  13. Analysis of tangent hyperbolic nanofluid impinging on a stretching cylinder near the stagnation point

    Directory of Open Access Journals (Sweden)

    T. Salahuddin

    Full Text Available An analysis is executed to study the influence of heat generation/absorption on tangent hyperbolic nanofluid near the stagnation point over a stretching cylinder. In this study the developed model of a tangent hyperbolic nanofluid in boundary layer flow with Brownian motion and thermophoresis effects are discussed. The governing partial differential equations in terms of continuity, momentum, temperature and concentration are rehabilitated into ordinary differential form and then solved numerically using shooting method. The results specify that the addition of nanoparticles into the tangent hyperbolic fluid yields an increment in the skin friction coefficient and the heat transfer rate at the surface. Comparison of the present results with previously published literature is specified and found in good agreement. It is noticed that velocity profile reduces by enhancing Weissenberg number λ and power law index n. The skin friction coefficient, local Nusselt number and local Sherwood number enhances for large values of stretching ratio parameter A. Keywords: Stagnation point flow, Tangent hyperbolic nanofluid, Stretching cylinder, Heat generation/absorption, Boundary layer, Shooting method

  14. Stagnation of the exploitation of Al ores and the depression of world prices of Al

    Directory of Open Access Journals (Sweden)

    Slavkovský Jozef

    1999-03-01

    Full Text Available In the contribution, data on Al – a metal of the 20th century are compiled together with the problems of genesis of the Al mineral raw ma-terials as well as types of bauxite and Al-laterite deposits. Furthermore, an overview of the world exploitation of bauxite during 1935-1980 is given along with the prognoses to 2000 and present situation (1992-1996. Overviews of the production of Al follows, providing its rela-tion to the bauxite exploitation. Contrary to the prognoses, a stabilization or stagnation has been observed in the exploitation of bauxite and production of Al during nineties, which a tendency is directly reflected in the world price of this commodity. When analyzing the Al prices for a longer period, some serious deviations can be noticed, that however presently represent a long-term minimum. We hope the stagnation of the production and the price decline are only temporary and new possibilities of the utilization of Al will be found soon.

  15. Athlete atypicity on the edge of human achievement: performances stagnate after the last peak, in 1988.

    Directory of Open Access Journals (Sweden)

    Geoffroy Berthelot

    2010-01-01

    Full Text Available The growth law for the development of top athletes performances remains unknown in quantifiable sport events. Here we present a growth model for 41351 best performers from 70 track and field (T&F and swimming events and detail their characteristics over the modern Olympic era. We show that 64% of T&F events no longer improved since 1993, while 47% of swimming events stagnated after 1990, prior to a second progression step starting in 2000. Since then, 100% of swimming events continued to progress.We also provide a measurement of the atypicity for the 3919 best performances (BP of each year in every event. The secular evolution of this parameter for T&F reveals four peaks; the most recent (1988 followed by a major stagnation. This last peak may correspond to the most recent successful attempt to push forward human physiological limits. No atypicity trend is detected in swimming. The upcoming rarefaction of new records in sport may be delayed by technological innovations, themselves depending upon economical constraints.

  16. Stagnation-point flow of second grade nanofluid towards a nonlinear stretching surface with variable thickness

    Directory of Open Access Journals (Sweden)

    Rai Sajjad Saif

    Full Text Available This paper investigates the stagnation point flow of second grade nanomaterial towards a nonlinear stretching surface subject to variable surface thickness. The process of heat transfer is examined through the melting heat and mixed convection effects. Further novel features regarding Brownian motion and thermophoresis are present. Boundary-layer approximation is employed in the problem formulation. Momentum, energy and concentration equations are converted into the non-linear ordinary differential system through the appropriate transformations. Convergent solutions for resulting problem are computed. Behaviors of various sundry variables on temperature and concentration are studied in detail. The skin friction coefficient and heat and mass transfer rates are also computed and analyzed. Our results indicate that the temperature and concentration distributions are enhanced for larger values of thermophoresis parameter. Further the present work is hoped to be useful in improving the performance of heat transfer of base fluid. Keywords: Stagnation-point flow, Second grade fluid, Nanoparticles, Melting heat process, Nonlinear stretching surface, Variable surface thickness

  17. Quantification of MagLIF stagnation morphology using the Mallat Scattering Transformation

    Science.gov (United States)

    Glinsky, Michael; Weis, Matthew; Jennings, Christopher; Ampleford, David; Harding, Eric; Knapp, Patrick; Gomez, Matthew

    2017-10-01

    The morphology of the stagnated plasma resulting from MagLIF is measured by imaging the self-emission x-rays coming from the multi-keV plasma. Equivalent diagnostic response can be derived from integrated rad-hydro simulations from programs such as Hydra and Gorgon. There have been only limited quantitative ways to compare the image morphology, that is the texture, of the simulations to that of the experiments, to compare one experiment to another, or to compare one simulation to another. We have developed a metric of image morphology based on the Mallat Scattering Transformation, a transformation that has proved to be effective at distinguishing textures, sounds, and written characters. This metric has demonstrated excellent performance in classifying an ensemble of synthetic stagnations images. A good regression of the scattering coefficients to the parameters used to generate the synthetic images was found. Finally, the metric has been used to quantitatively compare simulations to experimental self-emission images. Sandia National Laboratories is a multi-mission laboratory managed and operated by NTESS, LLC., a wholly owned subsidiary of Honeywell International, Inc., for the USDoEs NNSA under contract DE-NA0003525.

  18. Linear stability analysis of laminar flow near a stagnation point in the slip flow regime

    Science.gov (United States)

    Essaghir, E.; Oubarra, A.; Lahjomri, J.

    2017-12-01

    The aim of the present contribution is to analyze the effect of slip parameter on the stability of a laminar incompressible flow near a stagnation point in the slip flow regime. The analysis is based on the traditional normal mode approach and assumes parallel flow approximation. The Orr-Sommerfeld equation that governs the infinitesimal disturbance of stream function imposed to the steady main flow, which is an exact solution of the Navier-Stokes equation satisfying slip boundary conditions, is obtained by using the powerful spectral Chebyshev collocation method. The results of the effect of slip parameter K on the hydrodynamic characteristics of the base flow, namely the velocity profile, the shear stress profile, the boundary layer, displacement and momentum thicknesses are illustrated and discussed. The numerical data for these characteristics, as well as those of the eigenvalues and the corresponding wave numbers recover the results of the special case of no-slip boundary conditions. They are found to be in good agreement with previous numerical calculations. The effects of slip parameter on the neutral curves of stability, for two-dimensional disturbances in the Reynolds-wave number plane, are then obtained for the first time in the slip flow regime for stagnation point flow. Furthermore, the evolution of the critical Reynolds number against the slip parameter is established. The results show that the critical Reynolds number for instability is significantly increased with the slip parameter and the flow turn out to be more stable when the effect of rarefaction becomes important.

  19. Stagnation point flow of hyperbolic tangent fluid with Soret-Dufour effects

    Directory of Open Access Journals (Sweden)

    Tasawar Hayat

    Full Text Available Combined effects of Soret (thermal-diffusion and Dufour (diffusion-thermo in MHD stagnation point flow of tangent hyperbolic fluid by a stretching sheet are discussed in the present article. The laws of conservation of mass, momentum, energy and concentration are employed to develop the mathematical model of physical phenomenon. Suitable transformations lead to convert the nonlinear partial differential equations into the ordinary differential equations. The series solutions of boundary layer equations along with boundary conditions are obtained. Convergence of the developed series solutions is discussed via plots and numerical values. The behaviors of different physical parameters on the velocity, temperature and concentration fields are plotted and analyzed. Numerical values of skin friction coefficient, local Nusselt and Sherwood numbers are computed and analyzed. It is found that Dufour and Soret numbers result in the enhancement of temperature and concentration distributions, respectively. Furthermore a comparison is presented with the previous published results in a limiting way to justify the present solutions. Keywords: Magnetohydrodynamics (MHD, Stagnation point flow, Tangent hyperbolic fluid, Soret-Dufour effects

  20. Spontaneous breaking of supersymmetry

    Energy Technology Data Exchange (ETDEWEB)

    Zumino, B.

    1981-12-01

    There has been recently a revival of interest in supersymmetric gauge theories, stimulated by the hope that supersymmetry might help in clarifying some of the questions which remain unanswered in the so called Grand Unified Theories and in particular the gauge hierarchy problem. In a Grand Unified Theory one has two widely different mass scales: the unification mass M approx. = 10/sup 15/GeV at which the unification group (e.g. SU(5)) breaks down to SU(3) x SU(2) x U(1) and the mass ..mu.. approx. = 100 GeV at which SU(2) x U(1) is broken down to the U(1) of electromagnetism. There is at present no theoretical understanding of the extreme smallness of the ratio ..mu../M of these two numbers. This is the gauge hierarchy problem. This lecture attempts to review the various mechanisms for spontaneous supersymmetry breaking in gauge theories. Most of the discussions are concerned with the tree approximation, but what is presently known about radiative correction is also reviewed.

  1. Bootstrap Dynamical Symmetry Breaking

    Directory of Open Access Journals (Sweden)

    Wei-Shu Hou

    2013-01-01

    Full Text Available Despite the emergence of a 125 GeV Higgs-like particle at the LHC, we explore the possibility of dynamical electroweak symmetry breaking by strong Yukawa coupling of very heavy new chiral quarks Q . Taking the 125 GeV object to be a dilaton with suppressed couplings, we note that the Goldstone bosons G exist as longitudinal modes V L of the weak bosons and would couple to Q with Yukawa coupling λ Q . With m Q ≳ 700  GeV from LHC, the strong λ Q ≳ 4 could lead to deeply bound Q Q ¯ states. We postulate that the leading “collapsed state,” the color-singlet (heavy isotriplet, pseudoscalar Q Q ¯ meson π 1 , is G itself, and a gap equation without Higgs is constructed. Dynamical symmetry breaking is affected via strong λ Q , generating m Q while self-consistently justifying treating G as massless in the loop, hence, “bootstrap,” Solving such a gap equation, we find that m Q should be several TeV, or λ Q ≳ 4 π , and would become much heavier if there is a light Higgs boson. For such heavy chiral quarks, we find analogy with the π − N system, by which we conjecture the possible annihilation phenomena of Q Q ¯ → n V L with high multiplicity, the search of which might be aided by Yukawa-bound Q Q ¯ resonances.

  2. Comparing the 2000 and 2005 factors affecting the selling price of feeder cattle sold at Arkansas livestock auctions.

    Science.gov (United States)

    Troxel, T R; Barham, B L

    2007-12-01

    The objectives of the study were to determine how factors affecting the selling price of feeder calves changed from 2000 to 2005 and to examine the perception that discounts narrow or even disappear as calf supplies decrease and selling prices increase. Data from weekly Arkansas livestock auctions were collected from January 1 to December 31 in 2000 and 2005. Data included calf sex, breed type, color, muscle score, horn status, frame score, fill, condition, health, and BW. Mean selling prices for 2000 and 2005 were $92.91 +/- 15.05 and $118.32 +/- 15.13 (mean +/- SD; $/45.45 kg), respectively. Individual price observations were subtracted from the respective annual means and became the dependent variable. The selling prices for feeder calves sold in groups of 2 to 5 calves and in groups of >/= 6 calves were greater in 2005 than 2000 (P Brahman (P Brahman Cross, Charolais, Charolais x Limousin, Hereford x Limousin, Limousin, Limousin x one-fourth Brahman, Longhorn, Saler and Simmental. Yellow-white face, black-white face, black, and gray feeder calves received an increase in selling price from 2000 to 2005 (P < 0.001). Although fewer horned feeder calves were sold in 2005 (P < 0.01), they received greater discounts in 2005 than 2000 (-$2.86 +/- 0.16 and -$0.51 +/- 0.09; P < 0.001). In 2005, large-framed feeder calves did not receive the premium detected in 2000, but medium-framed feeder calves in 2005 received a greater selling price compared with 2000. Feeder calves with a muscle score of 1 received a greater premium in 2005 compared with 2000 ($2.58 +/- 0.06 and $0.02 +/- 0.09, respectively; P < 0.001). Feeder calves with a muscle score of 2 were discounted in both years, but the discount in 2005 was not as great as in 2000 (P < 0.001). Full and tanked feeder calves received greater discounts in 2005 than in 2000 (P < 0.001). Discounts for fleshy and fat feeder calves were greater in 2005 than in 2000. Most factors affecting the selling price of Arkansas feeder

  3. Identification of molecules derived from human fibroblast feeder cells that support the proliferation of human embryonic stem cells

    DEFF Research Database (Denmark)

    Anisimov, Sergey V.; Christophersen, Nicolaj S.; Correia, Ana S.

    2011-01-01

    The majority of human embryonic stem cell lines depend on a feeder cell layer for continuous growth in vitro, so that they can remain in an undifferentiated state. Limited knowledge is available concerning the molecular mechanisms that underlie the capacity of feeder cells to support both...... the proliferation and pluripotency of these cells. Importantly, feeder cells generally lose their capacity to support human embryonic stem cell proliferation in vitro following long-term culture. In this study, we performed large-scale gene expression profiles of human foreskin fibroblasts during early...

  4. Effect of Feeder Configuration on the Microstructure of Ductile Cast Iron

    DEFF Research Database (Denmark)

    Vedel-Smith, Nikolaj Kjelgaard; Tiedje, Niels Skat

    2014-01-01

    iron castings. The goal is to enable metallurgists and foundry engineers to more directly target mushy zone development to prolong the possibility to feed through this section. Keeping smaller section open for an extended period will make it possible to use fewer or smaller feeders, with reduced energy......Feeding and microstructure of a test casting rigged with different feeder combinations was studied. Castings were examined and classified by soundness and microstructure. Subsequently the casting macro- and microstructure was analyzed to study how differences in solidification and segregation...... influence the soundness of different sections of the castings. Moreover, the microstructural changes due to variations in thermal gradients are classified, and the variations in the mushy zone described. The paper discusses how solidification and segregation influence porosity and microstructure of ductile...

  5. Underwater wireless optical communication using a blue-light leaky feeder

    Science.gov (United States)

    Xu, Jing; Sun, Bin; Kong, Meiwei; Lin, Aobo; Sarwar, Rohail; Han, Jun; Zhang, Wei; Deng, Ning

    2017-08-01

    A novel concept of using a leaky plastic optical fiber (POF) as the leaky feeder for underwater wireless optical communication (UWOC) is proposed and experimentally demonstrated. The leaky POF can potentially improve the UWOC coverage. Orthogonal frequency division multiplexing (OFDM) is employed in the demonstration to increase spectral efficiency and robustness to modal dispersion of the leaky POF with a large core. A bit rate of 224.61 Mb/s (net bit rate: 183.69 Mb/s) at the two discrete radiation points along a 10-m leaky POF feeder is achieved using 16-quadrature amplitude modulation (QAM)-OFDM modulation. Over a 30-cm underwater channel, the mean bit errors (BERs) measured at the two points are 3.37×10-5 and 3.35×10-3, respectively, which are below the FEC threshold of 3.8×10-3.

  6. Effects of Home Energy Management Systems on Distribution Utilities and Feeders Under Various Market Structures: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Ruth, Mark; Pratt, Annabelle; Lunacek, Monte; Mittal, Saurabh; Wu, Hongyu; Jones, Wesley

    2015-07-17

    The combination of distributed energy resources (DER) and retail tariff structures to provide benefits to both utility consumers and the utilities is poorly understood. To improve understanding, an Integrated Energy System Model (IESM) is being developed to simulate the physical and economic aspects of DER technologies, the buildings where they reside, and feeders servicing them. The IESM was used to simulate 20 houses with home energy management systems on a single feeder under a time of use tariff to estimate economic and physical impacts on both the households and the distribution utilities. HEMS reduce consumers’ electric bills by precooling houses in the hours before peak electricity pricing. Household savings are greater than the reduction utility net revenue indicating that HEMS can provide a societal benefit providing tariffs are structured so that utilities remain solvent. Utilization of HEMS reduce peak loads during high price hours but shifts it to hours with off-peak and shoulder prices and resulting in a higher peak load.

  7. The effects of automated scatter feeders on captive grizzly bear activity budgets.

    Science.gov (United States)

    Andrews, Nathan L P; Ha, James C

    2014-01-01

    Although captive bears are popular zoo attractions, they are known to exhibit high levels of repetitive behaviors (RBs). These behaviors have also made them particularly popular subjects for welfare research. To date, most research on ursid welfare has focused on various feeding methods that seek to increase time spent searching for, extracting, or consuming food. Prior research indicates an average of a 50% reduction in RBs when attempts are successful and, roughly, a 50% success rate across studies. This research focused on decreasing time spent in an RB while increasing the time spent active by increasing time spent searching for, extracting, and consuming food. The utility of timed, automated scatter feeders was examined for use with captive grizzly bears (Ursis arctos horribilis). Findings include a significant decrease in time spent in RB and a significant increase in time spent active while the feeders were in use. Further, the bears exhibited a wider range of behaviors and a greater use of their enclosure.

  8. A novel NIH/3T3 duplex feeder system to engineer corneal epithelial sheets with enhanced cytokeratin 15-positive progenitor populations.

    Science.gov (United States)

    Miyashita, Hideyuki; Shimmura, Shigeto; Higa, Kazunari; Yoshida, Satoru; Kawakita, Tetsuya; Shimazaki, Jun; Tsubota, Kazuo

    2008-07-01

    Corneal epithelial cell sheets co-cultivated with feeder cells are used to reconstruct the ocular surface in stem cell-depleted eyes. The present study was conducted to investigate the optimal method of using feeder cells in the interest of preserving progenitor cells in cultivated sheets. We compared the phenotype and secondary colony forming efficiency (CFE) of cell sheets that were engineered using 3T3 feeder cells as a separate layer or as a contact layer. We also devised a novel "duplex feeder" system that consists of two separate layers of feeder cells. After cells reached confluence, cells were cultured at the air-liquid interface to allow full stratification. Stratified sheets were then analyzed using immunohistochemistry and secondary colony formation. Contact feeder cultures and duplex feeder cultures yielded epithelial sheets with small, cuboid basal cells with strong expression of keratin (K)3, K12, and K 15. Furthermore, only duplex feeder layers reproduced the basal K 15, suprabasal K12 limbal phenotype where epithelial stem cells reside. A similar effect was observed when cornea stroma-derived progenitor cells were used as feeder cells. Duplex feeder sheets also produced significantly more secondary colonies than cells dissociated from single layer sheets, suggesting that the duplex feeder system produces transplantable sheets with a higher yield of progenitor cells.

  9. Hybrid RSOA and fibre raman amplified long reach feeder link for WiMAX-on-fibre

    DEFF Research Database (Denmark)

    Amaya Fernández, Ferney Orlando; Martinez, Javier; Yu, Xianbin

    2009-01-01

    A distributed fibre Raman amplified long reach optical access feeder link using a reflective semiconductor optical amplifier in the remote base station is experimentally demonstrated for supporting WiMAXover- fibre transmission. The measured values for the error vector magnitude for quadrature ph...... phase shift keying and 16-ary quadrature amplitude modulation after 40 km of fibre transmission meet the IEEE 820.16 standard requirements...

  10. Decision Support for Optimal Repositioning of Containers in a Feeder System

    OpenAIRE

    Danijela Tuljak-Suban; Elen Twrdy

    2008-01-01

    The transport of empty containers represents a seriousproblem in the fast growing sphere of maritime container transport.The most widespread type of container transport organizationin maritime transport is the hub and spoke mode, whichenables the transport of a great number of containers via largevessels between hub ports, from where feeder ships transport tosmaller ports that thus gravitate to the central hub port. The articlecontains a detailed analysis of the northern Adriatic portsand the...

  11. Lake Bacterial Assemblage Composition Is Sensitive to Biological Disturbance Caused by an Invasive Filter Feeder

    OpenAIRE

    Vincent J. Denef; Hunter J. Carrick; Joann Cavaletto; Edna Chiang; Thomas H. Johengen; Henry A. Vanderploeg; Angela D. Kent

    2017-01-01

    ABSTRACT One approach to improve forecasts of how global change will affect ecosystem processes is to better understand how anthropogenic disturbances alter bacterial assemblages that drive biogeochemical cycles. Species invasions are important contributors to global change, but their impacts on bacterial community ecology are rarely investigated. Here, we studied direct impacts of invasive dreissenid mussels (IDMs), one of many invasive filter feeders, on freshwater lake bacterioplankton. We...

  12. Grounding System Studies for Transformer-less Collector Feeder of Full-Scale Power Converters

    DEFF Research Database (Denmark)

    Sztykiel, Michal; Teodorescu, Remus; Munk-Nielsen, Stig

    2013-01-01

    Following work examines current and voltage distribution during ground faults in cables of the transformer-less feeder system consisting of interconnected voltage source converters. Analysis is performed with regard to converter block operation, fault-ride-through requirements, cable design...... and different grounding schemes. Analysis show, that systems with effective grounded generator's neutral in general provide best ground current and voltage distribution across cables....

  13. Break the Pattern!

    DEFF Research Database (Denmark)

    Hasse, Cathrine; Trentemøller, Stine

    Break the Pattern! A critical enquiry into three scientific workplace cultures: Hercules, Caretakers and Worker Bees is the third publication of the international three year long project "Understanding Puzzles in the Gendered European Map" (UPGEM). By contrasting empirical findings from academic...... workplaces in the five UPGEM-countries (Denmark, Estonia, Finland, Italy and Poland) we identify three clusters of cultural patterns in physics as culture. We call these Hercules, Caretakers and Worker Bees. We also consider the influence of national cultural historical processes on the scientific culture...... (physics in culture) and discuss how physics as and in culture influence the perception of science, of work and family life, of the interplay between religion and science as well as how physics as culture can either hinder or promote the career of female scientists....

  14. Thermal analysis of the cryostat feed through for the ITER Tokamak TF feeder

    Science.gov (United States)

    Zhang, Shanwen; Song, Yuntao; Lu, Kun; Wang, Zhongwei; Zhang, Jianfeng; Qin, Yongfa

    2017-04-01

    In Tokamaks, the toroidal field (TF) coil feeder is an important component that is used to supply the cryogens and electrical power for the TF coils. As a part of the TF feeder, the cryostat-feed through (CFT) is subject to low temperatures of 9 and 80 K inside and room temperature of 300 K outside. Based on the features of the International Thermonuclear Experimental Reactor TF feeder, the thermal performance of the CFT under the nominal conditions is studied. Taking into account the conductive, convective and radiation heat transfer, the finite element model of the CFT is built. Transient thermal analysis is performed to determine the temperatures of the CFT on the 9th day of cooldown. The model is assessed by comparing the cooling curves of the CFT after 9 days. If the simulation and experimental results are the same, the finite element model can be considered as calibrated. The model predicts that the cooling time will be approximately 26 days and the temperature distribution and heat load of the main components are obtained when the CFT reaches thermal equilibrium. This study provides a valid quantitative characterization of the CFT design.

  15. Urbanization affects neophilia and risk-taking at bird-feeders

    Science.gov (United States)

    Tryjanowski, Piotr; Møller, Anders Pape; Morelli, Federico; Biaduń, Waldemar; Brauze, Tomasz; Ciach, Michał; Czechowski, Paweł; Czyż, Stanisław; Dulisz, Beata; Goławski, Artur; Hetmański, Tomasz; Indykiewicz, Piotr; Mitrus, Cezary; Myczko, Łukasz; Nowakowski, Jacek J.; Polakowski, Michał; Takacs, Viktoria; Wysocki, Dariusz; Zduniak, Piotr

    2016-06-01

    Urban environments cover vast areas with a high density of humans and their dogs and cats causing problems for exploitation of new resources by wild animals. Such resources facilitate colonization by individuals with a high level of neophilia predicting that urban animals should show more neophilia than rural conspecifics. We provided bird-feeders across urban environments in 14 Polish cities and matched nearby rural habitats, testing whether the presence of a novel item (a brightly coloured green object made out of gum with a tuft of hair) differentially delayed arrival at feeders in rural compared to urban habitats. The presence of a novel object reduced the number of great tits Parus major, but also the total number of all species of birds although differentially so in urban compared to rural areas. That was the case independent of the potentially confounding effects of temperature, population density of birds, and the abundance of cats, dogs and pedestrians. The number of great tits and the total number of birds attending feeders increased in urban compared to rural areas independent of local population density of birds. This implies that urban birds have high levels of neophilia allowing them to readily exploit unpredictable resources in urban environments.

  16. Computation of Locational and Hourly Maximum Output of a Distributed Generator Connected to a Distribution Feeder

    Science.gov (United States)

    Hayashi, Yasuhiro; Matsuki, Junya; Hanai, Yuji; Hosokawa, Shinpei; Kobayashi, Naoki

    Recently, the total number of distributed generation such as photovoltaic generation system and wind turbine generation system connected to distribution network is drastically increased. Distributed generation utilizing renewable energy can reduce the distribution loss and emission of CO2. However the distribution network with the distributed generators must be operated keeping reliability of power supply and power quality. In this paper, the authors propose a computation method to determine the maximum output of a distributed generator under the operational constrains ((1) voltage limit, (2) line current capacity, and (3) no reverse flow to bank) at arbitrary connection point and hourly period. In the proposed method, three-phase iterative load flow calculation is applied to evaluate the above operational constraints. Three-phase iterative load flow calculation has two simple procedures: (Procedure1) addition of load currents from terminal node of feeder to root one, and (Procedure2) subtraction of voltage drop from root node of feeder to terminal one. In order to check the validity of the proposed method, numerical simulations are accomplished for a distribution system model. Furthermore, characteristics of locational and hourly maximum output of distributed generator connected to distribution feeder are analyzed by several numerical examples.

  17. Evaluation of the Fretting Resistance of the High Voltage Insulation on the ITER Magnet Feeder Busbars

    Science.gov (United States)

    Clayton, N.; Crouchen, M.; Evans, D.; Gung, C.-Y.; Su, M.; Devred, A.; Piccin, R.

    2017-12-01

    The high voltage (HV) insulation on the ITER magnet feeder superconducting busbars and current leads will be prepared from S-glass fabric, pre-impregnated with an epoxy resin, which is interleaved with polyimide film and wrapped onto the components and cured during feeder manufacture. The insulation architecture consists of nine half-lapped layers of glass/Kapton, which is then enveloped in a ground-screen, and two further half-lapped layers of glass pre-preg for mechanical protection. The integrity of the HV insulation is critical in order to inhibit electrical arcs within the feeders. The insulation over the entire length of the HV components (bus bar, current leads and joints) must provide a level of voltage isolation of 30 kV. In operation, the insulation on ITER busbars will be subjected to high mechanical loads, arising from Lorentz forces, and in addition will be subjected to fretting erosion against stainless steel clamps, as the pulsed nature of some magnets results in longitudinal movement of the busbar. This work was aimed at assessing the wear on, and the changes in, the electrical properties of the insulation when subjected to typical ITER operating conditions. High voltage tests demonstrated that the electrical isolation of the insulation was intact after the fretting test.

  18. Manufacture and test of prototype water pipe chase barrier in ITER Magnet Feeder system

    Energy Technology Data Exchange (ETDEWEB)

    Lu, Kun, E-mail: lukun@ipp.ac.cn [Institute of Plasma Physics, Shushan Hu Road 350, Hefei, Anhui (China); Wen, Xinjie; Liu, Chen; Song, Yuntao [Institute of Plasma Physics, Shushan Hu Road 350, Hefei, Anhui (China); Niu, Erwu [ITER China, 15B Fuxing Road, Beijing 100862 (China); Gung, Chenyu; Su, Man [ITER Organization, Route de Vinon-sur-Verdon – CS 90046, 13067 St Paul-lez-Durance Cedex (France)

    2016-11-01

    The Magnet Feeder system in the International Thermonuclear Experimental Reactor (ITER) deploys electrical currents and supercritical helium to the superconducting magnets and the magnet diagnostic signals to the operators. In the current design, the feeders located in the upper L3 level of the Tokamak gallery penetrate the Tokamak coolant water system vault, the biological shield and the cryostat. As a secondary confinement to contain the activated coolant water in the vault in the case of water pipe burst accident, a water barrier is welded between the penetration in the water pipe chase outer wall and the mid-plane of the vacuum jacket of the Feeder Coil Terminal Box (CTB). A thin-wall stainless steel diaphragm with an omega shape profile is welded around the CTB as the water barrier to endure 2 bar hydraulic pressure. In addition, the barrier is designed as a flexible compensator to withstand a maximum of 15 mm of axial displacement of the CTB in case of helium leak accident without failure. This paper presents the detail configuration, the manufacturing and assembly processes of the water barrier. Test results of the prototype water barrier under simulated accident conditions are also reported. Successful qualification of the design and manufacturing process of the water barrier lays a good foundation for the series production of this subsystem.

  19. Rainy Periods and Bottom Water Stagnation Initiating Brine Accumulation and Metal Concentrations: 1. The Late Quaternary

    Science.gov (United States)

    Rossignol-Strick, Martine

    1987-06-01

    A working hypothesis is proposed to account for the present accumulation of brines in isolated pockets of the ocean floor and for the formation of the underlying organic and metal-rich sediments. These are the Tyro and Bannock basins in the East Mediterranean, the Red Sea Deeps, and the Orca Basin in the northern Gulf of Mexico. Initiation of brine-derived deposition in the Red Sea Deeps and Orca Basin occurred between 12,000 and 8000 years B.P. This time bracket also encompasses the formation of the latest East Mediterranean sapropel and the wettest global climate since the last glacial maximum. This wet period first appeared in the tropics around 12,000 years B.P, then in the subtropical and middle latitudes. During the same period, the 23,000 year precession cycle brought the summer insolation of the northern hemisphere to its peak at 11,000 years B.P. with retreating northern hemisphere ice sheets. The Red Sea Deeps and the Orca Basin became anoxic during this humid period, and metal-rich sapropel deposition then began. In contrast, the Tyro and Bannock basins began accumulating a brine long before and persisted beyond this climatic stage. The hypothesis involves two propositions: (1) As in the Eastern Mediterranean Sea, marine anoxia was mainly the consequence of the large influx of continental runoff and local precipitation. Longer residence time of bottom waters, so-called "stagnation," in silled rimmed basins would have resulted from lower salinity at the sea surface in areas of deep water formation in the Eastern Mediterranean, the Red Sea, and the Gulf of Mexico and (2) Miocene or older evaporites underlie these basins or outcrop on their flanks. Leaching from these evaporites was an ongoing process before the quasi-stagnation phase, but the initial leachate, much less saline than the present brines, was continuously flushed by bottom circulation. The climate-induced quiescence of bottom waters in these basins enabled the leachate to accumulate. The

  20. Breaking soliton equations and negative-order breaking soliton ...

    Indian Academy of Sciences (India)

    Home; Journals; Pramana – Journal of Physics; Volume 87; Issue 5. Breaking soliton ... We use the simplified Hirota's method to obtain multiple soliton solutions for each developed breaking soliton equation. We also develop ... WAZWAZ1. Department of Mathematics, Saint Xavier University, Chicago, IL 60655, USA ...

  1. Breaking soliton equations and negative-order breaking soliton ...

    Indian Academy of Sciences (India)

    We develop breaking soliton equations and negative-order breaking soliton equations of typical and higher orders. The recursion operator of the KdV equation is used to derive these models.We establish the distinctdispersion relation for each equation. We use the simplified Hirota's method to obtain multiple soliton ...

  2. Break location effects on PWR small break LOCA phenomena

    International Nuclear Information System (INIS)

    Suzuki, Mitsuhiro

    1989-01-01

    The report presents experimental results of a small lower plenum break test of SB-PV-01 conducted at the large-Scale Test Facility (LSTF) of the Rig-of-Safety Assessment (ROSA)-IV program. This test simulates a loss-of-coolant accident (LOCA) caused by instrument tubes break (break area corresponds to 0.5% of the cold leg flow area) in a Westinghouse-type pressurized water reactor (PWR) assuming both manual actuation for all of the high pressure injection (HPI) systems and failure of the auxiliary feedwater systems. The report clarifies long-term system responses, especially the core cooling conditions related to the primary mass inventory. Also it clarifies break location effects on small break LOCA phenomena by comparing other five similar LOCA tests with break locations at cold leg, hot leg, upper head, pressurizer top (TMI-type) and SG U-tubes. It is coucluded that the lower plenum break is the severest on core heatup due to the highest break flow rate and the least primary mass recovery after the ECCS among the six tests. (author)

  3. Breaking soliton equations and negative-order breaking soliton ...

    Indian Academy of Sciences (India)

    2016-10-06

    Oct 6, 2016 ... Abstract. We develop breaking soliton equations and negative-order breaking soliton equations of typical and higher orders. The recursion operator of the KdV equation is used to derive these models. We establish the distinct dispersion relation for each equation. We use the simplified Hirota's method to ...

  4. Application of offset-CT scanning to the inspection of high power feeder lines and connections

    Science.gov (United States)

    Schneberk, Daniel; Maziuk, Robert; Soyfer, Boris; Shashishekhar, N.; Alreja, Rahul

    2016-02-01

    VJT is developing techniques and scanning methods for the in-situ Radiographic and Computed Tomographic inspection of underground high-power feeder cables. The goals for the inspection are to measure the 3D state of the cables and the cable-connections. Recent in-situ Digital Radiographic inspections performed by VJT have demonstrated the value of NDE inspection information for buried power lines. These NDE data have raised further questions as to the exact state of the cables and connections and pointed to the need for more 3D information of the type provided by volumetric CT scanning. VJT is pursuing a three phased approach to address the many issues involved in this type of inspection: 1) develop a high-power feeder-cable test-bed CT scanner, 2) acquire scans on underground feeder pipes that have been removed from service, and 3) from the work in 1) and 2) develop limited-angle CT scanning methods for extending in-situ Digital Radiography to volumetric CT measurements. To this end, VJT has developed and fielded a high-energy test-bed Gantry-type CT scanner (the source and detector move around the object) with a number of important properties. First, the geometry of the gantry-scans can be configured to match the techniques used in the in-situ radiographic inspection. The same X-ray source is employed as in portable Radiographic inspections, a 7.5 MeV Betatron coupled to a Perkin-Elmer Amorphous Silicon detector. Offset-CT scanning is employed as the high-power feeder line assembly is larger than the detector. A description of this scanner and the scan geometry will be presented showing the connection to in-situ radiography. Results from the CT scans of high-power feeder-cable specimens removed from service will be presented with a focus on the inspection potential of volumetric CT data on these assemblies. An evaluation of the scan performance properties of these data compared to the spectrum of life-cycle inspection issues will be presented. Continuing and

  5. Forest feeder root dynamics are controlled by spatiotemporal position, inherent characteristics and resource availability

    Science.gov (United States)

    Coleman, M.

    2012-12-01

    Fine roots are the conduit for carbon allocation from forest trees to soil. Information on species-specific allocation patterns is crucial for predicting responses to changing environmental conditions. Yet models for belowground allocation are based on generalizations with few supporting observations. It is rare to have long-term observations of fine root dynamics compared among species and levels of resource availability. Here I present the results for fine root dynamics monitored over six years following establishment of a replicated trial comparing cottonwood (CW) and loblobloly pine (LP) grown without amendment (C), with fertilization (F), irrigation (I) or their combination (IF). The trial is located at the Savannah River Site near New Ellenton, SC, USA. Species and time since establishment had larger effects on feeder root production and mortality with relatively minor effects from irrigation and fertilization treatments. Both cumulative production and mortality followed sigmoid growth curves during six years of establishment. Cumulative production for LP was consistently 30% lower than CW throughout observations, while species differences in cumulative mortality reached the same magnitude and direction, but only after four growing seasons. Fertilization, but not irrigation, had a significant positive effect on cottonwood feeder root production. Fertilized cottonwood cumulative feeder root production was 57% greater than non-fertilizer, while fertilized pine cumulative production was 16% lower than non-fertilizer. There were no irrigation and fertilizer treatment differences in cumulative feeder root mortality identified with the repeated measures analysis approach. Survival analysis was used to evaluate factors controlling the risk of root mortality, account for covariates and to achieve greater sensitivity. Predominate factors affecting the risk of root mortality were in order: depth in soil, year of observation, root diameter at appearance, and season of

  6. Replacement of murine fibroblasts by human fibroblasts irradiated in obtaining feeder layer for the culture of human keratinocytes

    Energy Technology Data Exchange (ETDEWEB)

    Yoshito, Daniele; Sufi, Bianca S.; Santin, Stefany P.; Mathor, Monica B. [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil); Altran, Silvana C.; Isaac, Cesar [Universidade Sao Paulo (USP), Sao Paulo, SP (Brazil). Fac. de Medicina. Lab. de Microcirurgia Plastica; Esteves-Pedro, Natalia M. [Universidade Sao Paulo (USP), Sao Paulo, SP (Brazil). Fac. de Ciencias Farmaceuticas. Lab. de Controle Biologico; Herson, Marisa R. [DonorTissue Bank of Victoria (Australia)

    2011-07-01

    Human autologous epithelia cultivated in vitro, have been used successfully in treating damage to skin integrity. The methodology allowed the cultivation of these epithelia was described by Rheinwald and Green in 1975, this methodology consisted in seeding keratinocytes onto a feeder layer composed of lineage 3T3 murine fibroblasts, the proliferation rate is controlled through the action of ionizing radiation. However, currently there is a growing concern about the possibility of transmitting prions and murine viruses to transplanted patients. Taking into account this concern, in this present work, we replaced the feeder layer originally composed of murine fibroblasts by human fibroblasts. To obtain this new feeder layer was necessary to standardize the enough irradiation dose to inhibit the replication of human fibroblasts and the verification of effectiveness of the development of keratinocytes culture on a feeder layer thus obtained. According to the obtained results we can verify that the human fibroblasts irradiated at various tested doses (60, 70, 100, 200, 250 and 300 Gy) had their mitotic activity inactivated by irradiation, allowing the use of any of these doses to confection of the feeder layer, since these fibroblasts irradiated still showed viable until fourteen days of cultivation. In the test of colony formation efficiency was observed that keratinocytes seeded on irradiated human fibroblasts were able to develop satisfactorily, preserving their clonogenic potential. Therefore it was possible the replacement of murine fibroblasts by human fibroblasts in confection of the feeder layer, in order to eliminate this xenobiotic component of the keratinocytes culture. (author)

  7. Replacement of murine fibroblasts by human fibroblasts irradiated in obtaining feeder layer for the culture of human keratinocytes

    International Nuclear Information System (INIS)

    Yoshito, Daniele; Sufi, Bianca S.; Santin, Stefany P.; Mathor, Monica B.; Altran, Silvana C.; Isaac, Cesar

    2011-01-01

    Human autologous epithelia cultivated in vitro, have been used successfully in treating damage to skin integrity. The methodology allowed the cultivation of these epithelia was described by Rheinwald and Green in 1975, this methodology consisted in seeding keratinocytes onto a feeder layer composed of lineage 3T3 murine fibroblasts, the proliferation rate is controlled through the action of ionizing radiation. However, currently there is a growing concern about the possibility of transmitting prions and murine viruses to transplanted patients. Taking into account this concern, in this present work, we replaced the feeder layer originally composed of murine fibroblasts by human fibroblasts. To obtain this new feeder layer was necessary to standardize the enough irradiation dose to inhibit the replication of human fibroblasts and the verification of effectiveness of the development of keratinocytes culture on a feeder layer thus obtained. According to the obtained results we can verify that the human fibroblasts irradiated at various tested doses (60, 70, 100, 200, 250 and 300 Gy) had their mitotic activity inactivated by irradiation, allowing the use of any of these doses to confection of the feeder layer, since these fibroblasts irradiated still showed viable until fourteen days of cultivation. In the test of colony formation efficiency was observed that keratinocytes seeded on irradiated human fibroblasts were able to develop satisfactorily, preserving their clonogenic potential. Therefore it was possible the replacement of murine fibroblasts by human fibroblasts in confection of the feeder layer, in order to eliminate this xenobiotic component of the keratinocytes culture. (author)

  8. Nonlinear radiative heat transfer to stagnation-point flow of Sisko fluid past a stretching cylinder

    Directory of Open Access Journals (Sweden)

    Masood Khan

    2016-05-01

    Full Text Available In the present paper, we endeavor to perform a numerical analysis in connection with the nonlinear radiative stagnation-point flow and heat transfer to Sisko fluid past a stretching cylinder in the presence of convective boundary conditions. The influence of thermal radiation using nonlinear Rosseland approximation is explored. The numerical solutions of transformed governing equations are calculated through forth order Runge-Kutta method using shooting technique. With the help of graphs and tables, the influence of non-dimensional parameters on velocity and temperature along with the local skin friction and Nusselt number is discussed. The results reveal that the temperature increases however, heat transfer from the surface of cylinder decreases with the increasing values of thermal radiation and temperature ratio parameters. Moreover, the authenticity of numerical solutions is validated by finding their good agreement with the HAM solutions.

  9. Recent productivity developments and technical change in Danish organic farming - stagnation?

    DEFF Research Database (Denmark)

    Sauer, Johannes; Graversen, Jesper Tranbjerg; Park, Tim

    This paper attempts to quantitatively measure the change in the productivity of Dan-ish organic farming in recent years by using panel data on 56 organic farms mainly engaged in milk production for the period 2002 to 2004. Based on a translog pro-duction frontier framework the technical and scale...... growth in organic production by estimating a bootstrapped bivariate probit model with respect to factors influencing the probability of organic market exit. The results revealed significant differencies in the organic farms’ technical efficiencies, no sig-nificant total factor productivity growth...... and even a slightly negative rate of technical change in the period investigated. These empirical results seem not strong enough to support the view of a profound stagnation in organic milk farming over the last years. We found evidence for a positive relationship between subsidy payments and an increase...

  10. Mixed Convection Unsteady Stagnation-Point Flow towards a Stretching Sheet with Slip Effects

    Directory of Open Access Journals (Sweden)

    Hui Chen

    2014-01-01

    Full Text Available The paper studies the unsteady mixed convection flow of an incompressible viscous fluid about a stagnation point on a stretching sheet in presence of velocity and thermal slips. The governing equations are transformed into the ordinary differential equations by using similarity transformations. The transformed equations are solved numerically by an efficient shooting method. The characteristics of the flow and heat transfer features for governing parameters are analyzed and discussed for both the assisting and opposing flows. It is found that dual solutions exist for certain range of buoyancy parameter λ which again depend on the unsteadiness parameter α and the slip parameters (i.e., δ and γ. The numerical results show that the increase of unsteadiness parameter and the slip effects cause increment in the existence range of similarity solution. The effects of unsteadiness parameter, the velocity ratio parameter, and the velocity and thermal slip parameters on the velocity and temperature distributions are analyzed and discussed.

  11. MHD stagnation point flow of Carreau fluid toward a permeable shrinking sheet: Dual solutions

    Directory of Open Access Journals (Sweden)

    N.S. Akbar

    2014-12-01

    Full Text Available Present analysis is carried out to study the two-dimensional stagnation-point flow of an in-compressible Carreau fluid toward a shrinking surface. The formulation of the Carreau fluid model has been developed first time for boundary layer problem of shrinking sheet and the governing partial differential equations are rehabilitated into ordinary differential equations using similarity transformations. The simplified nonlinear boundary value problem is solved by Runge-Kutta method after converting into the system of initial value problem using shooting method. Dual solutions are obtained graphically and results are shown for various parameters involved in the flow equations. Numerical values of skin friction coefficients are also computed.

  12. Free convection nanofluid flow in the stagnation-point region of a three-dimensional body.

    Science.gov (United States)

    Farooq, Umer; Xu, Hang

    2014-01-01

    Analytical results are presented for a steady three-dimensional free convection flow in the stagnation point region over a general curved isothermal surface placed in a nanofluid. The momentum equations in x- and y-directions, energy balance equation, and nanoparticle concentration equation are reduced to a set of four fully coupled nonlinear differential equations under appropriate similarity transformations. The well known technique optimal homotopy analysis method (OHAM) is used to obtain the exact solution explicitly, whose convergence is then checked in detail. Besides, the effects of the physical parameters, such as the Lewis number, the Brownian motion parameter, the thermophoresis parameter, and the buoyancy ratio on the profiles of velocities, temperature, and concentration, are studied and discussed. Furthermore the local skin friction coefficients in x- and y-directions, the local Nusselt number, and the local Sherwood number are examined for various values of the physical parameters.

  13. Numerical and series solutions for stagnation-point flow of nanofluid over an exponentially stretching sheet.

    Science.gov (United States)

    Mustafa, Meraj; Farooq, Muhammad A; Hayat, Tasawar; Alsaedi, Ahmed

    2013-01-01

    This investigation is concerned with the stagnation-point flow of nanofluid past an exponentially stretching sheet. The presence of Brownian motion and thermophoretic effects yields a coupled nonlinear boundary-value problem (BVP). Similarity transformations are invoked to reduce the partial differential equations into ordinary ones. Local similarity solutions are obtained by homotopy analysis method (HAM), which enables us to investigate the effects of parameters at a fixed location above the sheet. The numerical solutions are also derived using the built-in solver bvp4c of the software MATLAB. The results indicate that temperature and the thermal boundary layer thickness appreciably increase when the Brownian motion and thermophoresis effects are strengthened. Moreover the nanoparticles volume fraction is found to increase when the thermophoretic effect intensifies.

  14. Stagnation point flow and heat transfer over a nonlinear shrinking sheet with slip effects

    Directory of Open Access Journals (Sweden)

    N.F. Fauzi

    2015-12-01

    Full Text Available In this paper, an investigation is performed to analyze the effects of the slip parameters A and B on the steady stagnation-point flow and heat transfer due to a shrinking sheet in a viscous and incompressible fluid. Using similarity transformations, the governing boundary layer equations are transformed into the nonlinear ordinary (similar differential equations. The transformed equations are solved numerically using the shooting method. The dual solutions for velocity and temperature distribution exist for certain values of the positive constant velocity and temperature slip parameters. Likewise, a stability analysis has been performed to find the nature of the dual solutions. The velocity slip will delay the boundary layer separation whereas the temperature slip does not affect the boundary layer separation.

  15. Stagnation point flow and mass transfer with chemical reaction past a stretching/shrinking cylinder.

    Science.gov (United States)

    Najib, Najwa; Bachok, Norfifah; Arifin, Norihan Md; Ishak, Anuar

    2014-02-26

    This paper is about the stagnation point flow and mass transfer with chemical reaction past a stretching/shrinking cylinder. The governing partial differential equations in cylindrical form are transformed into ordinary differential equations by a similarity transformation. The transformed equations are solved numerically using a shooting method. Results for the skin friction coefficient, Schmidt number, velocity profiles as well as concentration profiles are presented for different values of the governing parameters. Effects of the curvature parameter, stretching/shrinking parameter and Schmidt number on the flow and mass transfer characteristics are examined. The study indicates that dual solutions exist for the shrinking cylinder but for the stretching cylinder, the solution is unique. It is observed that the surface shear stress and the mass transfer rate at the surface increase as the curvature parameter increases.

  16. Nonlinear radiative heat transfer to stagnation-point flow of Sisko fluid past a stretching cylinder

    Energy Technology Data Exchange (ETDEWEB)

    Khan, Masood [Department of Mathematics, Quaid-i-Azam University, Islamabad 44000 (Pakistan); Malik, Rabia, E-mail: rabiamalik.qau@gmail.com [Department of Mathematics, Quaid-i-Azam University, Islamabad 44000 (Pakistan); Department of Mathematics and Statistics, International Islamic University Islamabad 44000 (Pakistan); Hussain, M. [Department of Sciences and Humanities, National University of Computer and Emerging Sciences, Islamabad 44000 (Pakistan)

    2016-05-15

    In the present paper, we endeavor to perform a numerical analysis in connection with the nonlinear radiative stagnation-point flow and heat transfer to Sisko fluid past a stretching cylinder in the presence of convective boundary conditions. The influence of thermal radiation using nonlinear Rosseland approximation is explored. The numerical solutions of transformed governing equations are calculated through forth order Runge-Kutta method using shooting technique. With the help of graphs and tables, the influence of non-dimensional parameters on velocity and temperature along with the local skin friction and Nusselt number is discussed. The results reveal that the temperature increases however, heat transfer from the surface of cylinder decreases with the increasing values of thermal radiation and temperature ratio parameters. Moreover, the authenticity of numerical solutions is validated by finding their good agreement with the HAM solutions.

  17. [Analysis on establishment and affecting factors of qi stagnation and blood stasis rat model].

    Science.gov (United States)

    Wang, Tingting; Jia, Cheng; Chen, Yu; Li, Xin; Cheng, Jiayi

    2012-06-01

    To study on the method for establishing the Qi stagnation and blood stasis rat model and analyze the affecting factors. The orthogonal design was adopted to study the influences of joint stimulations including noise, light, electricity, ice water bath, tail-clamping on model rats. The 'flying spot' method was used to dynamically simulate blood flow velocity in microcirculation. the pressure sensing technology of MOTO was adopted to detect hemorheology-related indicators. And the coagulation method was used to detect blood coagulation-related indicators. Compared with the negative control group, all model groups showed significant reduction in the blood flow velocity in mesenteric microcirculation and increase in the whole blood viscosity at high, medium and low shear rate, the plasma viscosity and the fibrinogen content in four blood coagulation indicators. Noise, light, electricity, tail-clamping, bondage and icewater-bath make significant impact on model rats.

  18. Melting heat transfer in stagnation point flow of carbon nanotubes towards variable thickness surface

    Directory of Open Access Journals (Sweden)

    T. Hayat

    2016-01-01

    Full Text Available This work concentrates on the mathematical modeling for stagnation point flow of nanofluids over an impermeable stretching sheet with variable thickness. Carbon nanotubes [single-wall carbon nanotubes (SWCNTs and multi-wall carbon nanotubes (MWCNTs] as the nanoparticles are utilized. Water and kerosene oil are taken as the base fluids. Heat transfer through melting effect is discussed. Transformation procedure is adapted to obtain the non-linear ordinary differential equations from the fundamental laws of mass, linear momentum and energy. The optimal values of convergence control parameters and corresponding individual and total residual errors for SWCNTs and MWCNTs are computed by means of homotopy analysis method (HAM based BVPh 2.0. Characteristics of different involved parameters on the velocity, temperature, skin friction coefficient and Nusselt number are discussed. Higher velocity profile is observed for wall thickness parameter in case of water carbon nanotubes when compared with the kerosene oil carbon nanotubes.

  19. Categorization of flow conditions using Integral quantities for characterizing stagnation and recirculation

    International Nuclear Information System (INIS)

    Han, M.H.; Hwang, W.T.; Jeong, H.J.; Kim, E.H.

    2008-01-01

    This paper describes a method for categorizing an atmospheric flow condition of a site by using integral quantities for characterizing stagnation and recirculation. Authors have devised a method for categorizing flow conditions using distribution curves which represent the flow condition of the whole of Korea. It was found that the flow conditions for four nuclear power plant sites were good enough from a meteorological aspect. Among the four sites, Kori nuclear power plant site which is located at the south-eastern part of the Korean peninsular shows the best condition. Meteorological condition is the key factor for estimating the environmental effects of a nuclear facility. The devised method can be used for assessing the relative environmental risk of a nuclear facility with only meteorological data. And the devised categorization method can be used for choosing a suitable site for an industrial facility such as a nuclear power plant and a chemical complex. (author)

  20. Microbiological tap water profile of a medium-sized building and effect of water stagnation.

    Science.gov (United States)

    Lipphaus, Patrick; Hammes, Frederik; Kötzsch, Stefan; Green, James; Gillespie, Simon; Nocker, Andreas

    2014-01-01

    Whereas microbiological quality of drinking water in water distribution systems is routinely monitored for reasons of legal compliance, microbial numbers in tap water are grossly understudied. Motivated by gross differences in water from private households, we applied in this study flow cytometry as a rapid analytical method to quantify microbial concentrations in water sampled at diverse taps in a medium size research building receiving chlorinated water. Taps differed considerably in frequency of usage and were located in laboratories, bathrooms, and a coffee kitchen. Substantial differences were observed between taps with concentrations (per mL) in the range from 6.29 x 10(3) to 7.74 x 10(5) for total cells and from 1.66 x 10(3) to 4.31 x 10(5) for intact cells. The percentage of intact cells varied between 7% and 96%. Water from taps with very infrequent use showed the highest bacterial numbers and the highest proportions of intact cells. Stagnation tended to increase microbial numbers in water from those taps which were otherwise frequently used. Microbial numbers in other taps that were rarely opened were not affected by stagnation as their water is probably mostly stagnant. For cold water taps, microbial numbers and the percentage of intact cells tended to decline with flushing with the greatest decline for taps used least frequently whereas microbial concentrations in water from hot water taps tended to be somewhat more stable. We conclude that microbiological water quality is mainly determined by building-specific parameters. Tap water profiling can provide valuable insight into plumbing system hygiene and maintenance.

  1. Core break-off mechanism

    Science.gov (United States)

    Myrick, Thomas M. (Inventor)

    2003-01-01

    A mechanism for breaking off and retaining a core sample of a drill drilled into a ground substrate has an outer drill tube and an inner core break-off tube sleeved inside the drill tube. The break-off tube breaks off and retains the core sample by a varying geometric relationship of inner and outer diameters with the drill tube. The inside diameter (ID) of the drill tube is offset by a given amount with respect to its outer diameter (OD). Similarly, the outside diameter (OD) of the break-off tube is offset by the same amount with respect to its inner diameter (ID). When the break-off tube and drill tube are in one rotational alignment, the two offsets cancel each other such that the drill can operate the two tubes together in alignment with the drill axis. When the tubes are rotated 180 degrees to another positional alignment, the two offsets add together causing the core sample in the break-off tube to be displaced from the drill axis and applying shear forces to break off the core sample.

  2. supersymmetry breaking with extra dimensions

    Indian Academy of Sciences (India)

    This talk reviews some aspects of supersymmetry breaking in the presence of extra dimensions. The first part is a general introduction, recalling the motivations for supersymmetry and extra dimensions, as well as some unsolved problems of four-dimensional models of supersymmetry breaking. The central part is a more ...

  3. Inflation from supersymmetry breaking

    Energy Technology Data Exchange (ETDEWEB)

    Antoniadis, I. [UMR CNRS 7589 Sorbonne Universites, UPMC Paris 6, LPTHE, Paris (France); University of Bern, Albert Einstein Center, Institute for Theoretical Physics, Bern (Switzerland); Chatrabhuti, A.; Isono, H.; Knoops, R. [Chulalongkorn University, Department of Physics, Faculty of Science, Pathumwan, Bangkok (Thailand)

    2017-11-15

    We explore the possibility that inflation is driven by supersymmetry breaking with the superpartner of the goldstino (sgoldstino) playing the role of the inflaton. Moreover, we impose an R-symmetry that allows one to satisfy easily the slow-roll conditions, avoiding the so-called η-problem, and leads to two different classes of small-field inflation models; they are characterised by an inflationary plateau around the maximum of the scalar potential, where R-symmetry is either restored or spontaneously broken, with the inflaton rolling down to a minimum describing the present phase of our Universe. To avoid the Goldstone boson and be left with a single (real) scalar field (the inflaton), R-symmetry is gauged with the corresponding gauge boson becoming massive. This framework generalises a model studied recently by the present authors, with the inflaton identified by the string dilaton and R-symmetry together with supersymmetry restored at weak coupling, at infinity of the dilaton potential. The presence of the D-term allows a tuning of the vacuum energy at the minimum. The proposed models agree with cosmological observations and predict a tensor-to-scalar ratio of primordial perturbations 10{sup -9}

  4. Pair distribution functions of colloidal particles on a quartz collector in a parallel plate and stagnation point flow chamber

    NARCIS (Netherlands)

    Yang, JL; Busscher, HJ; Bos, R.R.M.

    2000-01-01

    Pair distribution functions of polystyrene particles adhering on a quartz collector surface are compared for a parallel plate (PP) and stagnation point (SP) flow chamber at a common Peclet number and identical surface coverage. Radial pair distribution functions of deposition patterns around the

  5. The stagnation of the Mexican male life expectancy in the first decade of the 21st century

    DEFF Research Database (Denmark)

    Canudas-Romo, Vladimir; García-Guerrero, Víctor Manuel; Echarri-Cánovas, Carlos Javier

    2015-01-01

    OBJECTIVES: In the first decade of the 21st century, the Mexican life expectancy changed from a long trend of increase to stagnation. These changes concur with an increase in deaths by homicides that the country experienced in that decade, and an obesity epidemic that had developed over the last ...

  6. Interdependence between core and peripheries of the European economy: secular stagnation and growth in the Western Balkans

    Directory of Open Access Journals (Sweden)

    Will Bartlett

    2017-09-01

    Full Text Available European countries are economically dependent upon each other. This paper therefore embeds the analysis of the Western Balkan countries within a wider perspective of the European economy as a whole. It combines a simple core-periphery model with an under-consumption model to provide an explanation of the emergence of secular stagnation, the dependency relationships between the core and peripheries of the European economy, and the spillover effects of Eurozone crisis to the Western Balkans. Due to tendencies to under-consumption, the core countries have been vulnerable to secular stagnation. In order to overcome this tendency within the Eurozone they are dependent on export revenues from the peripheries to sustain their economic growth. This has led to high trade and current account deficits during the boom and placed the peripheries in a highly vulnerable position during the recession period. Financialisation of the European economy has emerged as a response to the tendency towards secular stagnation, as the provision of consumer credit stimulated demand and temporarily overcame under consumption tendencies. The paper argues that continuing austerity, as a method to create internal devaluation, is unlikely to succeed as a means to extricate the periphery countries from the crisis. Given the dependencies of the European economies upon one another, a possibly better way out of the current period of low growth and stagnation would be a coordinated fiscal expansion to stimulate domestic and Europe-wide demand.

  7. Dynamic breaking of a single gold bond

    DEFF Research Database (Denmark)

    Pobelov, Ilya V.; Lauritzen, Kasper Primdal; Yoshida, Koji

    2017-01-01

    of a single Au-Au bond and show that the breaking force is dependent on the loading rate. We probe the temperature and structural dependencies of breaking and suggest that the paradox can be explained by fast breaking of atomic wires and slow breaking of point contacts giving very similar breaking forces....

  8. Effects of Gyejibongnyeong-hwan on dysmenorrhea caused by blood stagnation: study protocol for a randomized controlled trial

    Directory of Open Access Journals (Sweden)

    Park Jeong-Su

    2012-01-01

    Full Text Available Abstract Background Gyejibongnyeong-hwan (GJBNH is one of the most popular Korean medicine formulas for menstrual pain of dysmenorrhea. The concept of blood stagnation in Korean medicine is considered the main factor of causing abdominal pain, or cramps, during menstrual periods. To treat the symptoms, GJBNH is used to fluidify the stagnated blood and induce the blood flow to be smooth, reducing pain as the result. The purpose of this trial is to identify the efficacy of GJBNH in dysmenorrhea caused by blood stagnation. Methods This study is a multi-centre, randomised, double-blind, controlled trial with two parallel arms: the group taking GJBNH and the group taking placebo. 100 patients (women from age 18 to 35 will be enrolled to the trial. Through randomization 50 patients will be in experiment arm, and the other 50 patients will be in control arm. At the second visit (baseline, all participants who were already screened that they fulfil both the inclusion and the exclusion criteria will be randomised into two groups. Each group will take the intervention three times per day during two menstrual cycles. After the treatment for two cycles, each patient will be followed up during their 3rd, 4th and 5th menstrual cycles. From the screening (Visit 1 through the second follow-up (Visit 6 the entire process will take 25 weeks. Discussion This trial will provide evidence for the effectiveness of GJBNH in treating periodical pain due to dysmenorrhea that is caused by blood stagnation. The primary outcome between the two groups will be measured by changes in the Visual Analogue Score (VAS of pain. The secondary outcome will be measured by the Blood Stagnation Scale, the Short-form McGill questionnaire and the COX menstrual symptom scale. Analysis of covariance (ANCOVA and repeated measured ANOVA will be used to analyze the data analysis. Trial registration Current Controlled Trials: ISRCTN30426947

  9. Tumorigenic risk of human induced pluripotent stem cell explants cultured on mouse SNL76/7 feeder cells

    Energy Technology Data Exchange (ETDEWEB)

    Kamada, Mizuna; Mitsui, Youji, E-mail: y-mitsui8310@hb.tp1.jp; Kumazaki, Tsutomu; Kawahara, Yuta; Matsuo, Taira; Takahashi, Tomoko, E-mail: t-takahashi@kph.bunri-u.ac.jp

    2014-10-24

    Highlights: • hiPS cell explants formed malignant tumors when SNL76/7 feeder cells were used. • Multi type tumors developed by interaction of SNL76/7 feeder cells with hiPS cells. • Tumorigenic risk occurs by co-culture of hiPS cells with SNL76/7 feeder cells. - Abstract: The potential for tumor formation from transplanted human induced pluripotent stem cell (hiPSC) derivatives represents a high risk in their application to regenerative medicine. We examined the genetic origin and characteristics of tumors, that were formed when 13 hiPSC lines, established by ourselves, and 201B7 hiPSC from Kyoto University were transplanted into severe combined immune-deficient (SCID) mice. Though teratomas formed in 58% of mice, five angiosarcomas, one malignant solitary fibrous tumor and one undifferentiated pleomorphic sarcoma formed in the remaining mice. Three malignant cell lines were established from the tumors, which were derived from mitomycin C (MMC)-treated SNL76/7 (MMC-SNL) feeder cells, as tumor development from fusion cells between MMC-SNL and hiPSCs was negative by genetic analysis. While parent SNL76/7 cells produced malignant tumors, neither MMC-SNL nor MMC-treated mouse embryo fibroblast (MEF) produced malignant tumors. When MMC-SNL feeder cells were co-cultured with hiPSCs, growing cell lines were generated, that expressed genes similar to the parent SNL76/7 cells. Thus, hiPSCs grown on MMC-SNL feeder cells have a high risk of generating feeder-derived malignant tumors. The possible mechanism(s) of growth restoration and the formation of multiple tumor types are discussed with respect of the interactions between MMC-SNL and hiPSC.

  10. Meta-analysis on the effects of the physical environment, animal traits, feeder and feed characteristics on the feeding behaviour and performance of growing-finishing pigs.

    Science.gov (United States)

    Averós, X; Brossard, L; Dourmad, J Y; de Greef, K H; Edwards, S A; Meunier-Salaün, M C

    2012-08-01

    A meta-analysis, using information from 45 experiments on growing-finishing pigs published in 39 manuscripts, was carried out to determine the simultaneous effects of the physical environment (space allowance, group size, flooring conditions, temperature, presence of enrichment), pig traits (initial body weight (BW) for each studied time interval, sex, genetics), feeder characteristics (water provision within the feeder, feeder design (individual/collective), feeder places/pig, presence of feeder protection) and feed characteristics (feed allowance (ad libitum/restricted), net energy content, crude protein (CP) content), as well as their potential interactions, on the feeding behaviour and performance of growing-finishing pigs. The detrimental effect of low temperature on performance was particularly evident for restricted-fed pigs (P < 0.05). At reduced feeder space allowance, a reduction in the percentage of time spent eating was predicted when increasing initial BW, whereas the opposite was predicted for larger feeder space allowances (P < 0.001). The reduction in visit duration to the feeder in higher BW groups became gradually more important with increasing feeder space allowance (P < 0.01), whereas the increase in the ingestion rate and average daily feed intake (ADFI) with increasing initial BW became smaller with increasing feeder space (P < 0.05). The model predicted a reduction in feed conversion ratio (FCR) with increasing group size (P < 0.05) and floor space allowance (P < 0.01) and on solid floors with or without bedding (P < 0.05). In comparison with other feeders, wet/dry feeders were associated with more frequent but shorter feeder visits (P < 0.05), higher ingestion rates (P < 0.001) and higher ADFI (P < 0.10). The use of protection within individual feeders increased the time spent feeding (P < 0.001), reduced the number of visits per day (P < 0.01), the ingestion rate (P < 0.001) and FCR (P < 0.01) in comparison with other feeder types. Sex

  11. Metastable supersymmetry breaking without scales

    Energy Technology Data Exchange (ETDEWEB)

    Bruemmer, Felix

    2010-11-15

    We construct new examples of models of metastable D=4 N=1 supersymmetry breaking in which all scales are generated dynamically. Our models rely on Seiberg duality and on the ISS mechanism of supersymmetry breaking in massive SQCD. Some of the electric quark superfields arise as composites of a strongly coupled gauge sector. This allows us to start with a simple cubic superpotential and an asymptotically free gauge group in the ultraviolet, and end up with an infrared effective theory which breaks supersymmetry dynamically in a metastable state. (orig.)

  12. A New Optimization Framework To Solve The Optimal Feeder Reconfiguration And Capacitor Placement Problems

    Directory of Open Access Journals (Sweden)

    Mohammad-Reza Askari

    2015-07-01

    Full Text Available Abstract This paper introduces a new stochastic optimization framework based bat algorithm BA to solve the optimal distribution feeder reconfiguration DFR as well as the shunt capacitor placement and sizing in the distribution systems. The objective functions to be investigated are minimization of the active power losses and minimization of the total network costs an. In order to consider the uncertainties of the active and reactive loads in the problem point estimate method PEM with 2m scheme is employed as the stochastic tool. The feasibility and good performance of the proposed method are examined on the IEEE 69-bus test system.

  13. Demonstration of Market-Based Real-Time Electricity Pricing on a Congested Feeder

    DEFF Research Database (Denmark)

    Larsen, Emil Mahler; Pinson, Pierre; le Ray, Guillaume

    2015-01-01

    five minute electricity pricing is sent to demand. A method for forecasting demand and generating prices in a market framework is presented, and a novel mechanism to ensure prices are fair to customers who can and cannot participate is developed. The proposed market is currently being used to send......Congestion management can delay grid reinforcements needed due to the growth of distributed technologies like photovoltaics and electric vehicles. This paper presents a method of congestion management for low voltage feeders using indirect control from the smart grid demonstration EcoGrid EU, where...

  14. A Branch-and-Price Approach to the Feeder Network Design Problem

    DEFF Research Database (Denmark)

    Santini, Alberto; Plum, Christian Edinger Munk; Røpke, Stefan

    2017-01-01

    In this paper we consider the problem of designing a container liner shipping feeder network. The designer has to choose which port to serve during many rotations that start and end at a central hub. Many operational characteristics are considered, such as variable leg-by-leg speeds and cargo...... transit times. Realistic instances are generated from the LinerLib benchmark suite. The problem is solved with a branch-and-price algorithm, which can solve most instances to optimality within one hour. The results also provide insights on the cost structure and desirable features of optimal routes...

  15. The Linehaul-Feeder Vehicle Routing Problem with Virtual Depots and Time Windows

    Directory of Open Access Journals (Sweden)

    Huey-Kuo Chen

    2011-01-01

    Full Text Available This paper addresses the linehaul-feeder vehicle routing problem with virtual depots and time windows (LFVRPTW. Small and large vehicles deliver services to customers within time constraints; small vehicles en route may reload commodities from either the physical depot or from the larger vehicle at a virtual depot before continuing onward. A two-stage solution heuristic involving Tabu search is proposed to solve this problem. The test results show that the LFVRPTW performs better than the vehicle routing problem with time windows in terms of both objective value and the number of small vehicles dispatched.

  16. Modeling and Control of Low Voltage Flexible Units for Enhanced Operation of Distribution Feeders

    DEFF Research Database (Denmark)

    Raboni, Pietro; Hu, Weihao; Chaudhary, Sanjay

    2013-01-01

    In some networks Distributed Generators (DGs) are phasing out conventional power plants in terms of power production but still large efforts are required for providing ancillary services. In this paper the usage of fast response units like a Micro Turbines (MT) and a stationary Electric Vehicle...... Battery (EVB) is proposed for providing primary regulation in grid connected mode and for hierarchically manage an islanded LV distribution feeder. The unit models are described and a novel EVB model directly based on manufacturer’s data is proposed and evaluated comparing its performances with Sim...

  17. Large eddy simulation of premixed and non-premixed combustion in a Stagnation Point Reverse Flow combustor

    Science.gov (United States)

    Undapalli, Satish

    A new combustor referred to as Stagnation Point Reverse Flow (SPRF) combustor has been developed at Georgia Tech to meet the increasingly stringent emission regulations. The combustor incorporates a novel design to meet the conflicting requirements of low pollution and high stability in both premixed and non-premixed modes. The objective of this thesis work is to perform Large Eddy Simulations (LES) on this lab-scale combustor and elucidate the underlying physics that has resulted in its excellent performance. To achieve this, numerical simulations have been performed in both the premixed and non-premixed combustion modes, and velocity field, species field, entrainment characteristics, flame structure, emissions, and mixing characteristics have been analyzed. Simulations have been carried out first for a non-reactive case to resolve relevant fluid mechanics without heat release by the computational grid. The computed mean and RMS quantities in the non-reacting case compared well with the experimental data. Next, the simulations were extended for the premixed reactive case by employing different sub-grid scale combustion chemistry closures: Eddy Break Up (EBU), Artificially Thickened Flame (TF) and Linear Eddy Mixing (LEM) models. Results from the EBU and TF models exhibit reasonable agreement with the experimental velocity field. However, the computed thermal and species fields have noticeable discrepancies. Only LEM with LES (LEMLES), which is an advanced scalar approach, has been able to accurately predict both the velocity and species fields. Scalar mixing plays an important role in combustion, and this is solved directly at the sub-grid scales in LEM. As a result, LEM accurately predicts the scalar fields. Due to the two way coupling between the super-grid and sub-grid quantities, the velocity predictions also compare very well with the experiments. In other approaches, the sub-grid effects have been either modeled using conventional approaches (EBU) or need

  18. "The good into the pot, the bad into the crop!"--a new technology to free stem cells from feeder cells.

    Directory of Open Access Journals (Sweden)

    Annette Schneider

    Full Text Available A variety of embryonic and adult stem cell lines require an initial co-culturing with feeder cells for non-differentiated growth, self renewal and maintenance of pluripotency. However for many downstream ES cell applications the feeder cells have to be considered contaminations that might interfere not just with the analysis of experimental data but also with clinical application and tissue engineering approaches. Here we introduce a novel technique that allows for the selection of pure feeder-freed stem cells, following stem cell proliferation on feeder cell layers. Complete and reproducible separation of feeder and embryonic stem cells was accomplished by adaptation of an automated cell selection system that resulted in the aspiration of distinct cell colonies or fraction of colonies according to predefined physical parameters. Analyzing neuronal differentiation we demonstrated feeder-freed stem cells to exhibit differentiation potentials comparable to embryonic stem cells differentiated under standard conditions. However, embryoid body growth as well as differentiation of stem cells into cardiomyocytes was significantly enhanced in feeder-freed cells, indicating a feeder cell dependent modulation of lineage differentiation during early embryoid body development. These findings underline the necessity to separate stem and feeder cells before the initiation of in vitro differentiation. The complete separation of stem and feeder cells by this new technology results in pure stem cell populations for translational approaches. Furthermore, a more detailed analysis of the effect of feeder cells on stem cell differentiation is now possible, that might facilitate the identification and development of new optimized human or genetically modified feeder cell lines.

  19. Breaking beer bottles with cavitation

    Science.gov (United States)

    Jung, Sunny; Fontana, Jake; Palffy-Muhoray, Peter; Shelley, Michael

    2009-03-01

    Hitting the top of a beer bottle, nearly full of water, with an open hand can cause the bottle to break, with the bottom separating from upper section. We have studied this phenomenon using a high-speed camera, and observed the formation, coalescence and collapse of bubbles. The breaking of glass is due to cavitation, typically occurring near the bottom edge. We make numerical estimates of the relevant physical parameters, and compare these with experimental observations.

  20. Enhanced Particle Swarm Optimization-Based Feeder Reconfiguration Considering Uncertain Large Photovoltaic Powers and Demands

    Directory of Open Access Journals (Sweden)

    Ying-Yi Hong

    2014-01-01

    Full Text Available The Kyoto protocol recommended that industrialized countries limit their green gas emissions in 2012 to 5.2% below 1990 levels. Photovoltaic (PV arrays provide clear and sustainable renewable energy to electric power systems. Solar PV arrays can be installed in distribution systems of rural and urban areas, as opposed to wind-turbine generators, which cause noise in surrounding environments. However, a large PV array (several MW may incur several operation problems, for example, low power quality and reverse power. This work presents a novel method to reconfigure the distribution feeders in order to prevent the injection of reverse power into a substation connected to the transmission level. Moreover, a two-stage algorithm is developed, in which the uncertain bus loads and PV powers are clustered by fuzzy-c-means to gain representative scenarios; optimal reconfiguration is then achieved by a novel mean-variance-based particle swarm optimization. The system loss is minimized while the operational constraints, including reverse power and voltage variation, are satisfied due to the optimal feeder reconfiguration. Simulation results obtained from a 70-bus distribution system with 4 large PV arrays validate the proposed method.

  1. MSCs feeder layers induce SMG self-organization and branching morphogenesis.

    Science.gov (United States)

    Farahat, Mahmoud; Sathi, Gulsan Ara; Hara, Emilio Satoshi; Taketa, Hiroaki; Kuboki, Takuo; Matsumoto, Takuya

    2017-01-01

    Dysfunction of salivary glands leads to several oral health problems, including dental caries, mastication and swallowing dysfunctions and multiple oral infections. Conventional treatments for such condition fell short of providing satisfying therapeutic results. Recent advances in organ regeneration therapy which utilize tissue stem cells to fabricate bioengineered 3D organ buds, have introduced a promising therapeutic tool for full functional organ regeneration. However, finding a sustainable and easily accessible cell source for such approaches is still challenging, especially in case of severely atrophied tissues such as irradiated salivary glands. In response to this, we hypothesized that bone marrow derived mesenchymal stem cells (MSCs) could be used as feeder cells to induce salivary epithelial tissues/cells branching. Indeed, in 2D cultures, MSCs supported branching of embryonic submandibular salivary gland (SMG) epithelium. Interestingly, this enhancing effect was dependent on the initial number of MSC feeder cells. In addition, MSCs supported the self-assembly of SMG epithelial progenitor cells into well-patterned and branched 3D salivary organoids. Therefore, these findings propose MSCs as a valuable candidate cell source for induced SMG epithelial branching, which can potentially be applied in future methods for SMG regeneration approaches.

  2. Photovoltaic Hosting Capacity of Feeders with Reactive Power Control and Tap Changers

    Energy Technology Data Exchange (ETDEWEB)

    Ceylan, Oğuzhan; Paudyal, Sumit; Bhattarai, Bishnu P.; Myers, Kurt S.

    2017-06-01

    This paper proposes an algorithm to determine photovoltaic (PV) hosting capacity of power distribution networks as a function of number of PV injection nodes, reactive power support from the PVs, and the sub-station load tap changers (LTCs). In the proposed method, several minute by minute simulations are run based on randomly chosen PV injection nodes, daily PV output profiles, and daily load profiles from a pool of high-resolution realistic data set. The simulation setup is built using OpenDSS and MATLAB. The performance of the proposed method is investigated in the IEEE 123-node distribution feeder for multiple scenarios. The case studies are performed particularly for one, two, five and ten PV injection nodes, and looking at the maximum voltage deviations. Case studies show that the PV hosting capacity of the 123-node feeder greatly differs with the number of PV injection nodes. We have also observed that the PV hosting capacity increases with reactive power support and higher tap position of sub-station LTC.

  3. Power Hardware-in-the-Loop Evaluation of PV Inverter Grid Support on Hawaiian Electric Feeders

    Energy Technology Data Exchange (ETDEWEB)

    Nelson, Austin A [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Prabakar, Kumaraguru [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Nagarajan, Adarsh [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Nepal, Shaili [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Hoke, Anderson F [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Asano, Marc [Hawaiian Electric Company; Ueda, Reid [Hawaiian Electric Company; Ifuku, Earle [Hawaiian Electric Company

    2017-10-03

    As more grid-connected photovoltaic (PV) inverters become compliant with evolving interconnections requirements, there is increased interest from utilities in understanding how to best deploy advanced grid-support functions (GSF) in the field. One efficient and cost-effective method to examine such deployment options is to leverage power hardware-in-the-loop (PHIL) testing methods, which combine the fidelity of hardware tests with the flexibility of computer simulation. This paper summarizes a study wherein two Hawaiian Electric feeder models were converted to real-time models using an OPAL-RT real-time digital testing platform, and integrated with models of GSF capable PV inverters based on characterization test data. The integrated model was subsequently used in PHIL testing to evaluate the effects of different fixed power factor and volt-watt control settings on voltage regulation of the selected feeders using physical inverters. Selected results are presented in this paper, and complete results of this study were provided as inputs for field deployment and technical interconnection requirements for grid-connected PV inverters on the Hawaiian Islands.

  4. Trophic interactions between rhizosphere bacteria and bacterial feeders influenced by phosphate and aphids in barley

    DEFF Research Database (Denmark)

    Strandmark, Lisa Bjørnlund; Mørk, Søren; Madsen, Mette Vestergård

    2006-01-01

    The aim was to study the effects of P fertilization and leaf aphid attack on the trophic interactions of bacteria and bacterial feeders in the rhizospheres of barley plants. The density of protozoa peaked in the rhizospheres of plants fertilized with N and P, whereas nematodes peaked in the rhizo......The aim was to study the effects of P fertilization and leaf aphid attack on the trophic interactions of bacteria and bacterial feeders in the rhizospheres of barley plants. The density of protozoa peaked in the rhizospheres of plants fertilized with N and P, whereas nematodes peaked......-proteobacteria increased with P addition. To evaluate if differences in bacteria in terms of their quality as food could partly explain the observed differences in protozoan and nematode abundances, growth of the flagellate Cercomonas sp. was assessed with 935 bacteria isolated from the different treatments. This assay...... indicated that bacterial isolates were of higher food quality to Cercomonas sp. in NP than in N rhizospheres when plants were subjected to aphid attack. Bacteria of high and low food quality for Cercomonas sp., respectively, were fed to the nematode Caenorhabditis elegans and larval production examined. a...

  5. Effect of transport on blood selenium and glutathione status in feeder lambs.

    Science.gov (United States)

    Hall, J A; Bobe, G; Nixon, B K; Vorachek, W R; Hugejiletu; Nichols, T; Mosher, W D; Pirelli, G J

    2014-09-01

    Stress from transport may be linked to increased generation of reactive oxygen species, the removal of which requires reduced glutathione and selenium. The aim of this experiment was to examine the effect of transport on glutathione and Se status of feeder lambs. Recently weaned lambs (n = 40) were blocked by gender and BW on d 0 of the experiment and randomly assigned to 2 treatment groups: group 1, no transport and full access to feed and water (control), and group 2, 8-h road transport followed by another 16 h of feed deprivation (transport). After 24 h, both treatment groups were treated the same. All lambs were weighed, and blood samples were collected at 0, 8, 24, and 72 h and analyzed for whole-blood (WB) and serum Se concentrations, serum NEFA concentrations, and erythrocyte concentrations of glutathione. Transport of feeder lambs for 8 h followed by another 16 h of feed deprivation transiently (significant at 24 h but no longer different at 72 h) decreased BW and erythrocyte glutathione concentrations and increased serum NEFA and blood Se concentrations compared with control lambs. Our results suggest that 8 h of transport followed by another 16 h of feed deprivation results in fatty acid and Se mobilization from tissue stores with a coincident decrease in erythrocyte glutathione concentrations.

  6. Improvement of the auto wire feeder machine in a de-soldering process

    Directory of Open Access Journals (Sweden)

    Niramon Nonkhukhetkhong

    2016-10-01

    Full Text Available This paper presents the methodology of the de-soldering process for rework of disk drive Head Stack Assembly (HSA units. The auto wire feeder is a machine that generates Tin (Sn on the product. This machine was determined to be one of the major sources of excess Sn on the HSA. The defect rate due to excess Sn is more than 30%, which leads to increased processing time and cost to perform additional cleaning steps. From process analysis, the major causes of excess Sn are as follows: 1 The machine cannot cut the wire all the way into the flux core area; 2 The sizes and types of soldering irons are not appropriate for the unit parts; and, 3 There are variations introduced into the de-soldering process by the workforce. This paper proposes a methodology to address all three of these causes. First, the auto wire feeder machine in the de-solder process will be adjusted in order to cut wires into flux core. Second, the types of equipment and material used in de-soldering will be optimized. Finally, a new standard method for operators, which can be controlled more easily, will be developed in order to reduce defects due to workforce related variation. After these process controls and machine adjustments were implemented, the overall Sn related problems were significantly improved. Sn contamination was reduced by 41% and cycle time was reduced by an average of 15 seconds.

  7. Supervisory control and data acquisition system development for superconducting current feeder system of SST-1

    International Nuclear Information System (INIS)

    Patel, R.; Mahesuria, G.; Gupta, N.C.; Sonara, D.; Panchal, R.; Panchal, P.; Tanna, V.L.; Pradhan, S.

    2014-01-01

    The Current Feeders System (CFS) is essentially an optimized bridge between the power supply at room temperature and Super Conducting Magnet System (SCMS) of the SST-1 machine at 4.5 K.CFS is a complex electrical and cryogenic network which consists of ten pairs of 10 KA rating helium Vapor cooled Conventional Current Leads (VCCLs), superconducting (SC) current feeder and associated components. For the safe and reliable operation of CFS, it is equipped with different physical process parameters measuring instruments like flow, pressure, temperature, level, vacuum, voltage taps and final control element like control valves, heaters, vacuum pumps etc. PLC program is developed in ladder language for acquiring and controlling the process parameters. Independent SCADA applications developed in WonderwareIntouch software for data communication from PLC, front-end Graphical User Interface (GUI), auto-manual interface, real time trends, history trends, events and alarm pages. Time synchronized communication established between CFS control system and Industrial SQL server (InSQL) Historian for centralized storage of CFS process parameters which intern provides the CFS process data to SST-1 central control room. SCADA based data acquisition and data retrieval system is found to be satisfactory during the recent SST-1 cool down experiment. This paper describes the SCADA and PLC application development and their communication to InSQL server. (author)

  8. On radiative heat transfer in stagnation point flow of MHD Carreau fluid over a stretched surface

    Science.gov (United States)

    Khan, Masood; Sardar, Humara; Mudassar Gulzar, M.

    2018-03-01

    This paper investigates the behavior of MHD stagnation point flow of Carreau fluid in the presence of infinite shear rate viscosity. Additionally heat transfer analysis in the existence of non-linear radiation with convective boundary condition is performed. Moreover effects of Joule heating is observed and mathematical analysis is presented in the presence of viscous dissipation. The suitable transformations are employed to alter the leading partial differential equations to a set of ordinary differential equations. The subsequent non-straight common ordinary differential equations are solved numerically by an effective numerical approach specifically Runge-Kutta Fehlberg method alongside shooting technique. It is found that the higher values of Hartmann number (M) correspond to thickening of the thermal and thinning of momentum boundary layer thickness. The analysis further reveals that the fluid velocity is diminished by increasing the viscosity ratio parameter (β∗) and opposite trend is observed for temperature profile for both hydrodynamic and hydromagnetic flows. In addition the momentum boundary layer thickness is increased with velocity ratio parameter (α) and opposite is true for thermal boundary layer thickness.

  9. Diagnosing the Stagnation Conditions of MagLIF Implosions Using Co and Kr dopants

    Science.gov (United States)

    Harding, E. C.; Hansen, S. B.; Harvey-Thompson, A. J.; Weis, M. R.; Hahn, K. D.; Gomez, M. R.; Knapp, P. F.; Slutz, S. A.; Geissel, M.; Ampleford, D. J.; Jennings, C. A.; Peterson, K.; Rochau, G. A.; Doron, R.; Stambulchik, E.; Nedostup, O.; Maron, Y.; Golovkin, I.

    2017-10-01

    Recent experiments on the Z-machine tested several new diagnostic techniques for investigating the stagnation conditions and the origins of the mix present in a Magnetized Liner Inertial Fusion (MagLIF) target. For the first time we have collected K-shell spectra from a low-concentration, Kr dopant placed in the gaseous D2 fuel. In addition, thin Co coatings were strategically applied to three different internal surfaces of the target in order to assess which surfaces actively contribute to the contamination of the fuel. Both imaging spectroscopy and narrow-band crystal imaging were used to identify the location of He-like Co ions. The Te and ne of the Co is inferred by fitting the He-alpha lines and the near-by Li-like satellites. The experimental measurements and the challenges associated with the analysis will be discussed. Sandia Natl Lab is a multi-mission laboratory managed and operated by National Technology and Engineering Solutions of Sandia, LLC., a wholly owned subsidiary of Honeywell International, Inc., for the U.S. DOE NNSA under contract DE-NA-0003525.

  10. An automatic, stagnation point based algorithm for the delineation of Wellhead Protection Areas

    Science.gov (United States)

    Tosco, Tiziana; Sethi, Rajandrea; di Molfetta, Antonio

    2008-07-01

    Time-related capture areas are usually delineated using the backward particle tracking method, releasing circles of equally spaced particles around each well. In this way, an accurate delineation often requires both a very high number of particles and a manual capture zone encirclement. The aim of this work was to propose an Automatic Protection Area (APA) delineation algorithm, which can be coupled with any model of flow and particle tracking. The computational time is here reduced, thanks to the use of a limited number of nonequally spaced particles. The particle starting positions are determined coupling forward particle tracking from the stagnation point, and backward particle tracking from the pumping well. The pathlines are postprocessed for a completely automatic delineation of closed perimeters of time-related capture zones. The APA algorithm was tested for a two-dimensional geometry, in homogeneous and nonhomogeneous aquifers, steady state flow conditions, single and multiple wells. Results show that the APA algorithm is robust and able to automatically and accurately reconstruct protection areas with a very small number of particles, also in complex scenarios.

  11. Stagnation-point flow past a shrinking sheet in a nanofluid

    Science.gov (United States)

    Nazar, Roslinda; Jaradat, Mihaela; Arifin, Norihan M.; Pop, Ioan

    2011-10-01

    In this paper, the stagnation-point flow and heat transfer towards a shrinking sheet in a nanofluid is considered. The nonlinear system of coupled partial differential equations was transformed and reduced to a nonlinear system of coupled ordinary differential equations, which was solved numerically using the shooting method. Numerical results were obtained for the skin friction coefficient, the local Nusselt number as well as the velocity and temperature profiles for some values of the governing parameters, namely the nanoparticle volume fraction φ, the shrinking parameter λand the Prandtl number Pr. Three different types of nanoparticles are considered, namely Cu, Al2O3 and TiO2. It was found that nanoparticles of low thermal conductivity, TiO2, have better enhancement on heat transfer compared to nanoparticles Al2O3 and Cu. For a particular nanoparticle, increasing the volume fraction φ results in an increase of the skin friction coefficient and the heat transfer rate at the surface. It is also found that solutions do not exist for larger shrinking rates and dual solutions exist when λ < -1.0.

  12. Self-Generated Magnetic Fields in Stagnation-Phase ICF Implosions

    Science.gov (United States)

    Walsh, Christopher; Chittenden, Jeremy; McGlinchey, Kristopher; Niasse, Nicolas

    2016-10-01

    3-D extended-MHD simulations of the stagnation phase of an ICF implosion are presented, showing significant self-generated magnetic fields (1000-5000T) due to the Biermann Battery effect. Perturbed hot-spots generate magnetic fields at their edges, as the extremities of hot bubbles are rapidly cooled by the surrounding low temperature fuel, giving non-parallel electron pressure and density gradients. Larger amplitude and higher mode-number perturbations lead to an increased hot-spot surface area and more heat flow, developing greater non-parallel gradients and therefore larger magnetic fields. Due to this, largely perturbed hot-spots can be affected more by magnetic fields, although the accelerated cooling associated with greater deviations from symmetry lowers magnetisation. The Nernst effect advects magnetic field down temperature gradients towards the outer region of the hot-spot, which can also lower the magnetisation of the plasma. In some regions, however, the Nernst velocity is convergent, magnetising the tips of cold fuel spikes, resulting in anisotropic heat-flow and an improvement in energy containment. Low-mode and multi-high-mode simulations are shown, with magnetisations reaching sufficiently high levels in some regions of the hot-spot to suppress thermal conduction to lower than 50% of the unmagnetised case. A quantitative analysis of how this affects the hot-spot energy balance is included.

  13. Analytical study of the non orthogonal stagnation point flow of a micro polar fluid

    Directory of Open Access Journals (Sweden)

    M. Ali. Abbas

    2017-01-01

    Full Text Available In this paper we consider the steady two dimensional flow of micro polar fluids on a flat plate. The flow under discussion is the modified Hiemenz flow for a micro polar fluid which occurs in the hjkns + skms boundary layer near an orthogonal stagnation point. The full governing equation reduced to a modified Hiemenz flow. The solution to the boundary value problem is governed by two non dimensional parameters, the material parameter K and the ratio of the micro rotation to skin friction parameter n. The obtained nonlinear coupled ordinary differential equations are solved by using the Homotopy perturbation method. Comparison between numerical and analytical solutions of the problem is shown in tables form for different values of the governing parameters K and n. Effects of the material parameter K on the velocity profile and microrotation profiles for different cases of n are discussed graphically as well as numerically. Velocity profile decreases as the material parameter K increases and the microrotation profile increases as the material parameter K increases for different cases of n.

  14. Design of Two Feeder Three Phase Four Wire Distribution System Utilizing Multi Converter UPQC with Fuzzy Logic Controller

    Directory of Open Access Journals (Sweden)

    Chandra Babu Paduchuri

    2014-01-01

    Full Text Available This paper proposes the instantaneous p-q theory based fuzzy logic controller (FLC for multi converter unified power quality conditioner (MC-UPQC to mitigate power quality issues in two feeders three-phase four-wire distribution systems. The proposed system is extended system of the existing one feeder three-phase four-wire distribution system, which is operated with UPQC. This system is employed with three voltage source converters, which are connected commonly to two feeder distribution systems. The performance of this proposed system used to compensate voltage sag, neutral current mitigation and compensation of voltage and current harmonics under linear and nonlinear load conditions. The neutral current flowing in series transformers is zero in the implementation of the proposed system. The simulation performance analysis is carried out using MATLAB.

  15. Life Disparity before, during and after Stagnation of Danish Female Life Expectancy. a Cause of Death Analysis and a Comparison with Their Scandinavian Counterparts

    DEFF Research Database (Denmark)

    Aburto, José Manuel; Wensink, Maarten Jan; Lindahl-Jacobsen, Rune

    Low lifespan tends to go with high lifespan inequality. We find that stagnation in lifespan of Danish women (roughly 1975-1995) was accompanied by a similar albeit shorter period of stagnation in lifespan inequality. Cause-specifically, we find that this stagnation results largely from death from...... that as Norway increasingly came to resemble Sweden in terms of high life expectancy, it also came to resemble Sweden in terms of low lifespan inequality. Next, we aim to make similar decompositions for Sweden and Norway, and aim to disentangle cohort effects from the question: what can Denmark do now...

  16. Potential of building integrated photovoltaic solar energy generators in assisting daytime peaking feeders in urban areas in Brazil

    International Nuclear Information System (INIS)

    Ruether, Ricardo; Rebechi, Samuel Hilario; Knob, Paulo Jose; Da Silva Jardim, Carolina

    2008-01-01

    Because of the intermittent nature of the solar radiation resource, photovoltaic (PV) solar energy generation is considered a non-dispatchable power source. However, under some conditions, in sunny urban areas with electricity load curves dominated by air conditioning loads, there is a high correlation between PV generation and utility feeder loads. In these situations, a considerable fraction of a given PV generator can be considered dispatchable power. In this work, we assess the potential of grid connected, building integrated photovoltaic (BIPV) generation in the state capital, Florianopolis, in south Brazil (27 S, 48 W), which is supplied by the local utility company through 56 feeders. Our interest was to identify which feeder could obtain more benefits with implementation of a PV plant with a specific nominal power. Two factors are important in this analysis: the peak demand reduction value, and the LOLP (loss of load probability, in failures per year), or LOLE (loss of load expectation, in hours per year). We analyzed the hourly demand curves of the 56 feeders and compared them with the PV power generation values obtained from a 2 kW p BIPV installation that has been operating continuously for nearly 10 years connected to one of these feeders. For our calculations, we defined a PV installation of 1000 kWp AC , which corresponds to penetration level values between 10% and 20%, depending on the specific feeder considered. Our results demonstrate that the use of PV power plants can reduce significantly the summer demand peaks in regions where the load reflects commercial customers demand for midday air conditioning. (author)

  17. System and method for confining an object to a region of fluid flow having a stagnation point

    Science.gov (United States)

    Schroeder, Charles M. (Inventor); Shaqfeh, Eric S. G. (Inventor); Babcock, Hazen P. (Inventor); Chu, Steven (Inventor)

    2006-01-01

    A device for confining an object to a region proximate to a fluid flow stagnation point includes one or more inlets for carrying the fluid into the region, one or more outlets for carrying the fluid out of the region, and a controller, in fluidic communication with the inlets and outlets, for adjusting the motion of the fluid to produce a stagnation point in the region, thereby confining the object to the region. Applications include, for example, prolonged observation of the object, manipulation of the object, etc. The device optionally may employ a feedback control mechanism, a sensing apparatus (e.g., for imaging), and a storage medium for storing, and a computer for analyzing and manipulating, data acquired from observing the object. The invention further provides methods of using such a device and system in a number of fields, including biology, chemistry, physics, material science, and medical science.

  18. Role Overload, Role Self Distance, Role Stagnation as Determinants of Job Satisfaction and Turnover Intention in Banking Sector

    OpenAIRE

    Kunte, Monica; Gupta, Priya; Bhattacharya, Sonali; Neelam, Netra

    2017-01-01

    Purpose: This study examined the relationship of the organizational role stress: Role overload, role self-distance, and role stagnation with job satisfaction and turnover intention with a sample of banking employees in India. Methodology: In this research, we used the RODS scale developed by Prohit and Pareek (2010) for measuring occupational role scale. The reliability of the scale came out to be 0.71. Findings: The majority of employees of all ranks, in both private and public sector banks,...

  19. A study of flow field of feeder outlet pipe at CANDU for understanding flow accelerated(assistant) corrosion phenomena

    International Nuclear Information System (INIS)

    Kweon, H.; Seo, D. W.; Park, K. C.; Jeong, H. S.

    2002-01-01

    The FAC(Flow Accelerated Corrosion) on feeder outlet pipe is an important phenomena for surveying an integrity of CANDU plant. There are correlated a corrosion effect in electrochemistry and a flow field effect in hydrodynamics. A mass transfer rate is main governing parameter in macroscopic analysis of FAC phenomena. Therefore, first of all, at the hydrodynamic aspect the analysis of FAC is carried out. CFX 4.3 code calculates the flow field of feeder outlet pipe with complex geometry and the calculated results are estimated with an experimental data. On the basis of power plant data base, the worst location about wall thinning is compared with calculated and experimental location

  20. On breaks of the Indian monsoon

    Indian Academy of Sciences (India)

    For over a century, the term break has been used for spells in which the rainfall over the Indian monsoon zone is interrupted. The phenomenon of `break monsoon' is of great interest because long intense breaks are often associated with poor monsoon seasons. Such breaks have distinct circulation characteristics (heat ...

  1. The use of multiple imputation for the accurate measurements of individual feed intake by electronic feeders.

    Science.gov (United States)

    Jiao, S; Tiezzi, F; Huang, Y; Gray, K A; Maltecca, C

    2016-02-01

    Obtaining accurate individual feed intake records is the key first step in achieving genetic progress toward more efficient nutrient utilization in pigs. Feed intake records collected by electronic feeding systems contain errors (erroneous and abnormal values exceeding certain cutoff criteria), which are due to feeder malfunction or animal-feeder interaction. In this study, we examined the use of a novel data-editing strategy involving multiple imputation to minimize the impact of errors and missing values on the quality of feed intake data collected by an electronic feeding system. Accuracy of feed intake data adjustment obtained from the conventional linear mixed model (LMM) approach was compared with 2 alternative implementations of multiple imputation by chained equation, denoted as MI (multiple imputation) and MICE (multiple imputation by chained equation). The 3 methods were compared under 3 scenarios, where 5, 10, and 20% feed intake error rates were simulated. Each of the scenarios was replicated 5 times. Accuracy of the alternative error adjustment was measured as the correlation between the true daily feed intake (DFI; daily feed intake in the testing period) or true ADFI (the mean DFI across testing period) and the adjusted DFI or adjusted ADFI. In the editing process, error cutoff criteria are used to define if a feed intake visit contains errors. To investigate the possibility that the error cutoff criteria may affect any of the 3 methods, the simulation was repeated with 2 alternative error cutoff values. Multiple imputation methods outperformed the LMM approach in all scenarios with mean accuracies of 96.7, 93.5, and 90.2% obtained with MI and 96.8, 94.4, and 90.1% obtained with MICE compared with 91.0, 82.6, and 68.7% using LMM for DFI. Similar results were obtained for ADFI. Furthermore, multiple imputation methods consistently performed better than LMM regardless of the cutoff criteria applied to define errors. In conclusion, multiple imputation

  2. Effect of fuel pin ballooning on the sub-channel thermal hydraulics during small break loca for Indian PHWRS

    Energy Technology Data Exchange (ETDEWEB)

    Mukhopadhyay, D.; Behera, G.H.; Bandopadhyay, S.K.; Gupta, S.K. [Bhabha Atomic Research Centre, Div. Reactor Safety, Bombay (India)

    2001-07-01

    Effect of fuel pin ballooning on the subchannel thermal-hydraulics during a small break (0.25%) located at the Reactor Inlet Feeder (RIF) has been studied for Indian PHWRs. The break leads to a low flow situation in the affected reactor channel along with delayed reactor trip. Higher power to flow ratio in the inner subchannels in comparison to outer subchannel of a 19 pin fuel bundle causes early 2-phase condition causing the flow to by pass from the inner ones to outer ones. This causes the fuel pins to experience different temperatures. Fuel pin ballooning causes reduction in the subchannel areas and further flow redistribution takes place. The transient subchannel thermal-hydraulic conditions along the reactor channel are very much different due to the power distribution and pressure drop. (authors)

  3. Effects of the reacting flowfield on combustion processes in a Stagnation Point Reverse Flow combustor

    Science.gov (United States)

    Gopalakrishnan, Priya

    The performance of dry, low NOx gas turbines, which employ lean premixed (or partially premixed) combustors, is often limited by static and dynamic combustor stability, and they require complicated mixing hardware. To overcome these issues, a novel design, referred to as a Stagnation Point Reverse Flow (SPRF) combustor, has been recently demonstrated. The SPRF combustor has been shown to operate with ultra low NOx emissions in premixed and nonpremixed modes with gaseous and liquid fuels. The objective of this thesis is to elucidate the interactions between the flowfield and combustion processes in this novel combustor for gas- and liquid-fueled operation. This is achieved with experimental measurements employing various optical diagnostic techniques, which include Particle Image Velocimetry (PIV), chemiluminescence imaging, Planar Laser-Induced Fluorescence (PLIF) of OH radicals and elastic laser scattering from liquid droplets. The velocity measurements obtained during gas-fueled operation show that both nonreacting and reacting flows exhibit a "stagnation" region with low mean velocity and high RMS fluctuations. In nonreacting flow, it has been shown that the decay rate of the jet can be modeled as a combination of a free jet and a jet in a uniform opposed flow. The high shear between the forward and reverse flows causes significant recirculation, resulting in enhanced entrainment and mixing of the returning hot product gases into the incoming reactant jet for the reacting flow cases, which enables stable operation of the combustor at very lean equivalence ratios. Nonpremixed operation produces a flowfield similar to that of the premixed case except in the near-field region. The coaxial injector design results in high turbulence intensities close to the injector exit leading to significant fuel-air premixing before combustion occurs. The operation of the SPRF combustor fueled with liquid Jet-A is also experimentally investigated. The results indicate that while

  4. Life Disparity before, during and after Stagnation of Danish Female Life Expectancy. a Cause of Death Analysis and a Comparison with Their Scandinavian Counterparts

    DEFF Research Database (Denmark)

    Aburto, José Manuel; Wensink, Maarten Jan; Lindahl-Jacobsen, Rune

    Low lifespan tends to go with high lifespan inequality. We find that stagnation in lifespan of Danish women (roughly 1975-1995) was accompanied by a similar albeit shorter period of stagnation in lifespan inequality. Cause-specifically, we find that this stagnation results largely from death from...... cancers and non-infectious respiratory diseases, offsetting continuous improvement in cardiovascular mortality. Before and after stagnation, life expectancy increased as disparity decreased, as the cardiovascular revolution unfolded. Comparing Denmark and its Scandinavian counterparts, we find...... that as Norway increasingly came to resemble Sweden in terms of high life expectancy, it also came to resemble Sweden in terms of low lifespan inequality. Next, we aim to make similar decompositions for Sweden and Norway, and aim to disentangle cohort effects from the question: what can Denmark do now...

  5. Stagnation and complex flow in ruptured cerebral aneurysms: a possible association with hemostatic pattern.

    Science.gov (United States)

    Tsuji, Masanori; Ishikawa, Tatsuya; Ishida, Fujimaro; Furukawa, Kazuhiro; Miura, Yoichi; Shiba, Masato; Sano, Takanori; Tanemura, Hiroshi; Umeda, Yasuyuki; Shimosaka, Shinichi; Suzuki, Hidenori

    2017-05-01

    OBJECT Histopathological examination has revealed that ruptured cerebral aneurysms have different hemostatic patterns depending on the location of the clot formation. In this study, the authors investigated whether the hemostatic patterns had specific hemodynamic features using computational fluid dynamics (CFD) analysis. METHODS Twenty-six ruptured middle cerebral artery aneurysms were evaluated by 3D CT angiography and harvested at the time of clipping. The hemostatic patterns at the rupture points were assessed by means of histopathological examination, and morphological parameters were obtained. Transient analysis was performed, and wall shear stress-related hemodynamic parameters and invariant Q (vortex core region) were calculated. The morphological and hemodynamic parameters were compared among the hemostatic patterns. RESULTS Hematoxylin and eosin staining of the aneurysm wall showed 13 inside-pattern, 9 outside-pattern, and 4 other-pattern aneurysms. Three of the 26 aneurysms were excluded from further analysis, because their geometry models could not be generated due to low vascular CT values. Mann-Whitney U-tests showed that lower dome volume (0.04 cm 3 vs 0.12 cm 3 , p = 0.014), gradient oscillatory number (0.0234 vs 0.0289, p = 0.023), invariant Q (-0.801 10 -2 /sec 2 vs -0.124 10 -2 /sec 2 , p = 0.045) and higher aneurysm formation indicator (0.986 vs 0.963, p = 0.041) were significantly related to inside-pattern aneurysms when compared with outside-pattern aneurysms. CONCLUSIONS Inside-pattern aneurysms may have simpler flow patterns and less flow stagnation than outside-pattern aneurysms. CFD may be useful to characterize the hemostatic pattern of ruptured cerebral aneurysms.

  6. Impact of Water Chemistry, Pipe Material and Stagnation on the Building Plumbing Microbiome.

    Directory of Open Access Journals (Sweden)

    Pan Ji

    Full Text Available A unique microbiome establishes in the portion of the potable water distribution system within homes and other buildings (i.e., building plumbing. To examine its composition and the factors that shape it, standardized cold water plumbing rigs were deployed at the treatment plant and in the distribution system of five water utilities across the U.S. Three pipe materials (copper with lead solder, CPVC with brass fittings or copper/lead combined pipe were compared, with 8 hour flush cycles of 10 minutes to simulate typical daily use patterns. High throughput Illumina sequencing of 16S rRNA gene amplicons was employed to profile and compare the resident bulk water bacteria and archaea. The utility, location of the pipe rig, pipe material and stagnation all had a significant influence on the plumbing microbiome composition, but the utility source water and treatment practices were dominant factors. Examination of 21 water chemistry parameters suggested that the total chlorine concentration, pH, P, SO42- and Mg were associated with the most of the variation in bulk water microbiome composition. Disinfectant type exerted a notably low-magnitude impact on microbiome composition. At two utilities using the same source water, slight differences in treatment approaches were associated with differences in rare taxa in samples. For genera containing opportunistic pathogens, Utility C samples (highest pH of 9-10 had the highest frequency of detection for Legionella spp. and lowest relative abundance of Mycobacterium spp. Data were examined across utilities to identify a true universal core, special core, and peripheral organisms to deepen insight into the physical and chemical factors that shape the building plumbing microbiome.

  7. Structure and temperature distribution of a stagnation-point Diesel spray premixed flame

    International Nuclear Information System (INIS)

    Lin, J.-C.; Lin, Ta-Hui

    2005-01-01

    We experimentally examine the flow and flame characteristics of a stagnation point premixed flame influenced by Diesel sprays. In the experiment, distributions of drop size, drop axial velocity and its fluctuation as well as the gas phase temperature are measured by using the phase-doppler particle analyzer and a thin thermocouple. As might be expected, similar to the gasoline spray flame, the partially prevaporized Diesel spray flame is composed of a weak blue flame zone, indicating the burning of methane fuel, and a strongly luminous zone containing many bright yellow lines showing the passages of burning Diesel drops. It is found that the axial temperature profiles at various radial positions consist of an upstream preheat region, a maximum temperature downstream of the blue flame and a downstream region with a declined temperature curve because of the heat loss to the quartz plate. The SMD of the drops increases from the upstream preheat region to a maximum near the blue flame and then decreases in the downstream burning zone. Along the axial position, the drops are decelerated in front of the flame but accelerated when passing through the blue flame. It is also interesting to note that the radial distributions of SMD and number density of drops in the upstream region are mainly influenced by small drops flowing outward, since the upstream vaporization of Diesel drops is very limited; while those in the downstream region should be influenced by both small drops flowing outward and Diesel drops burning. From the experimental observations, there are impinging and bouncing of Diesel drops downstream of the spray flame near the quartz plate, resulting in a small amount of soot and carbon deposits on the wall. These interesting phenomena will be reported in the near future

  8. Isospin breaking from diquark clustering

    Science.gov (United States)

    Gibbs, W. R.; Dedonder, Jean-Pierre

    2017-09-01

    Background: Although SU(2) isospin symmetry is generally assumed in the basic theory of the strong interaction, a number of significant violations have been observed in scattering and bound states of nucleons. Many of these violations can be attributed to the electromagnetic interaction but the question of how much of the violation is due to it remains open. Purpose: To establish the connection between diquark clustering in the two-nucleon system and isospin breaking from the Coulomb interaction between the members of diquark pairs. Method: A schematic model based on clustering of quarks in the interior of the confinement region of the two-nucleon system is introduced and evaluated. In this model the Coulomb interaction is the source of all isospin breaking. It draws on a picture of the quark density based on the diquark-quark model of hadron structure which has been investigated by a number of groups. Results: The model produces three isospin breaking potentials connecting the unbroken value of the low-energy scattering amplitude to those of the p p , n n , and n p singlet channels. A simple test of the potentials in the three-nucleon energy difference problem yields results in agreement with the known binding energy difference. Conclusion: The illustrative model suggests that the breaking seen in the low-energy nucleon-nucleon (NN) interaction may be understood in terms of the Coulomb force between members of diquark clusters. It allows the prediction of the charge symmetry breaking interaction and the n n scattering length from the well measured n p singlet scattering length. Values of the n n scattering length around -18 fm are favored. Since the model is based on the quark picture, it can be easily extended, in the SU(3) limit, to calculate isospin breaking in the strange sector in the corresponding channels. A natural consequence of isospin breaking from diquark clustering is that the breaking in the strange sector, as measured by the separation energy

  9. A model for strategic selection of feeder management systems: A case study

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Hsing Hung [Faculty of Management and Administration, Macau University of Science and Technology, Avenue Wei Long, Taipa, Macau (China); Lee, Amy H.I. [Department of Industrial Management, Chung Hua University, No. 707, Sec. 2, Wu Fu Rd., Hsinchu 300 (China); Kang, He-Yau [Department of Industrial Engineering and Management, National Chin-Yi University of Technology, 35, Lane 215, Sec. 1, Chung San Rd., Taiping, Taichung 411 (China)

    2010-06-15

    The move to integrating distribution management system (DMS) and feeder management system (FMS) in China is becoming the main trend in recent years, in addition to upgrading and rebuilding existing energy management system (EMS) and DMS. However, with increasing complexity in the social environments along with rapidly changing technologies, how to select a suitable contractor and a FMS project is becoming an important issue for electric power companies. This paper first briefly introduces FMS and then lists its critical success criteria. A model that applies a multi-criteria decision-making (MCDM) method, an analytic network process (ANP) associated with benefits, opportunities, costs and risks (BOCR), is constructed to help power companies to select the most suitable FMS project. (author)

  10. Interactions among contaminant exposure route, kinetics and toxicity in marine deposit-feeders

    DEFF Research Database (Denmark)

    Selck, Henriette

    of a contaminant is bioavailable. The relationship among different combinations of exposure route (water vs. sediment), kinetics (i.e. uptake, internal fate, elimination) and toxicity were investigated in the polychaete Capitella species I and the brittle star Amphiura filiformis. Fluoranthene was used......Many of the chemicals having the greatest likelihood of causing damage in ecological systems, such as polycyclic aromatic hydrocarbons (PAHs) and metals are of persistent and/or hydrophobic character. Deposit-feeders may be important in facilitating the removal of organic contaminants from bulk...... and more ecologically relevant methods for use in risk assessment, relationships among adverse effects, time-dependent availability, internal transport and potential for trophic transfer need to be addressed....

  11. Feasibility of optimizing large utility electricity customers on a distribution feeder

    DEFF Research Database (Denmark)

    Pensini, Alessandro; Mammoli, A.

    2014-01-01

    the electricity price, which in turn reflects the DSO requirements. However, most optimization tools are intended for minimizing the costs of a single user and do not take into account the grid operation. If large customers in the same area optimize their schedules, unwanted ‘artificial’ peaks may occur...... on the feeder that the DSO has to deal with. Peaks height can be lowered by applying an upper bound to the purchased electricity in the mathematical formulation of the optimization problem. However, introducing a further constraint reduces the economic benefit for optimizing customers. This study assesses...... the peak reduction potential of introducing the additional constraint while keeping appealing economic benefits for the customers. DER-CAM, an optimization tool developed at LBNL was used for simulating the operation of three large typical commercial customers over a week. Results prove the peak shaving...

  12. A Survey of Pesticide Accumulation in a Specialist Feeder, the Koala (Phascolarctos cinereus).

    Science.gov (United States)

    Marschner, Caroline; Higgins, Damien P; Krockenberger, Mark B

    2017-09-01

    To maintain profitability in Australia's agricultural and urban landscapes pesticides are used throughout the range of koala habitats. The koala is a specialist feeder, reliant on metabolic enzyme capacities to utilise a toxic diet of eucalypt leaves and is potentially prone to adverse effects when xenobiotic interactions between dietary and anthropogenic xenobiotics occur. The aim of this study was to investigate accumulation of frequently used pesticides in wild koalas in 4 areas of New South Wales and Queensland. Liver samples of 57 deceased koalas were collected from care facilities and analysed using a modified QuEChERS extraction method followed by GCMSMS, HRLCMS and LCMSMS. No accumulation of any of the 166 investigated pesticides was found. Data indicate hepatic accumulation of pesticides in this species is uncommon even with close interactions with intensive land use. Despite the lack of hepatic bioaccumulation, this study cannot exclude a direct effect on hepatocellular metabolic pathways.

  13. Effect of feeders in 3D modeling of low impedance multilayer CPW transmission line

    Science.gov (United States)

    Zaini, R. I.; Kyabaggu, P. B. K.; Sinulingga, E. P.

    2018-02-01

    Improved characteristics with low dissipation loss MMICs are highly desirable for wireless communications. However, the current industrial MMIC design is mainly based on microstrip concept which suffered from parasitic and unwanted phenomenon especially at higher frequency (>20 GHz). On the other hand, for future wireless technology, higher frequency operation is required and on-wafer microwave characterizations as well as precise modeling of 3D Multilayer CPW components are vital. This project concerns with understanding of the microwave characteristics behavior of Multilayer CPW components in MMIC applications. Feeder effect as unwanted parts in the characteristics has been investigated to determine its relation with the half wavelength resonance of the Multilayer CPW Low Impedance Transmission Line.

  14. Trailer microclimate during commercial transportation of feeder cattle and relationship to indicators of cattle welfare.

    Science.gov (United States)

    Goldhawk, C; Crowe, T; Janzen, E; González, L A; Kastelic, J; Pajor, E; Schwartzkopf-Genswein, K S

    2014-11-01

    Nineteen loads of commercial feeder cattle (BW 376 ± 39 kg, mean ± SD) transported for 18 ± 4.5 h in summer and winter seasons were used to collect data on internal temperature and humidity conditions in the deck and belly compartment of pot-bellied trailers and their relationship with shrink, cortisol, and morbidity. Measurements of temperature or humidity at ceiling or animal level did not vary with transportation factors. Temperature and humidity ratio was greater at animal-level than ambient conditions during nonhighway travel and stationary periods (P 0.05). Evening loads (1700 and 2100 h) experienced more shrink in the summer than in the winter (11.2 ± 0.5 vs. 9.0 ± 0.5% of BW; P = 0.03). A 1°C increase in difference between average animal-level temperature in transit and the mean ambient temperature during the 10 d before transport was associated with a 0.11 ± 0.03% of BW increase in shrink (P 0.05). Despite association between indicators of calf welfare and microclimate, all cattle arrived in good condition and there was 0.96% treatment rate within the first 30 d after arrival. Management and auditing decisions related to transportation of feeder cattle should consider the relationship between animal-level and ambient conditions and conditions before transportation. Under the commercial conditions of the current study, the transportation process did not appear to cause distress according to the dimensions of animal welfare that were assessed.

  15. Complete nutrient content of four species of commercially available feeder insects fed enhanced diets during growth.

    Science.gov (United States)

    Finke, Mark D

    2015-11-01

    Commercially raised feeder insects used to feed captive insectivores are a good source of many nutrients but are deficient in several key nutrients. Current methods used to supplement insects include dusting and gut-loading. Here, we report on the nutrient composition of four species of commercially raised feeder insects fed a special diet to enhance their nutrient content. Crickets, mealworms, superworms, and waxworms were analyzed for moisture, crude protein, fat, ash, acid detergent fiber, total dietary fiber, minerals, amino acids, fatty acids, vitamins, taurine, carotenoids, inositol, and cholesterol. All four species contained enhanced levels of vitamin E and omega 3 fatty acids when compared to previously published data for these species. Crickets, superworms, and mealworms contained β-carotene although using standard conversion factors only crickets and superworms would likely contain sufficient vitamin A activity for most species of insectivores. Waxworms did not contain any detectable β-carotene but did contain zeaxanthin which they likely converted from dietary β-carotene. All four species contained significant amounts of both inositol and cholesterol. Like previous reports all insects were a poor source of calcium and only superworms contained vitamin D above the limit of detection. When compared to the nutrient requirements as established by the NRC for growing rats or poultry, these species were good sources of most other nutrients although the high fat and low moisture content of both waxworms and superworms means when corrected for energy density these two species were deficient in more nutrients than crickets or mealworms. These data show the value of modifying the diet of commercially available insects as they are growing to enhance their nutrient content. They also suggest that for most insectivores properly supplemented lower fat insects such as crickets, or smaller mealworms should form the bulk of the diet. © 2015 The Authors. Zoo Biology

  16. USULAN PERBAIKAN OPERATION POINT SHEET PADA MESIN FEEDER AIDA 1100 PT. XXX DENGAN MENGGUNAKAN METODE SMED

    Directory of Open Access Journals (Sweden)

    Ary Arvianto

    2012-02-01

    Full Text Available Single Minute Exchange of Die (SMED merupakan salah satu alat lean yang penting untuk mengurangi waste dan meningkatkan fleksibilitas dalam proses manufaktur yang memungkinkan dalam pengurangan ukuran lot dan perbaikan aliran manufaktur. SMED mengurangi waktu non-produktif dengan mempersatukan dan standardisasi operasi dalam pergantian alat, dengan menggunakan teknik sederhana dan aplikasi yang mudah. Namun proses tersebut tidak dapat memberikan hasil yang  spesifik dalam pelaksanaannya, dimana masih dapat dilakukan suatu perbaikan. Untuk mengatasi hal ini, data statistik dan alat-alat teknik industri dapat diintegrasikan dalam pendekatan SMED untuk meningkatkan hasil penerapan SMED. Penerapan pendekatan SMED yang diusulkan diuji untuk mesin feeder didalam industri otomotif PT. XXX. Implementasi ini memungkinkan adanya pengurangan waktu setup, melalui reorganisasi sumber daya internal perusahaan tanpa membutuhkan investasi yang signifikan.   Kata kunci: Lean manufacturing systems, Single Minute Exchange of Die, Quick ChangeOver.     Single Minute Exchange of Die (SMED is one of the essential lean tools to reduce waste and increase flexibility in manufacturing processes that enable the reduction of lot size and improving manufacturing flow. SMED reduces non-productive time by streamlining and standardizing operations in the turn of the tool, using simple techniques and easy application. But the process can not provide a specific result in the implementation, which can still be an improvement. To overcome this, statistical data and tools can be integrated in industrial engineering approaches to improve outcomes SMED SMED implementation. The proposed application of SMED approach was tested for the automotive industry in the feeder machine PT. XXX. This implementation allows for the reduction of setup time, through the reorganization of the company's internal resources without requiring significant investment. Keywords: Lean manufacturing

  17. Urban and rural habitats differ in number and type of bird feeders and in bird species consuming supplementary food.

    Science.gov (United States)

    Tryjanowski, Piotr; Skórka, Piotr; Sparks, Tim H; Biaduń, Waldemar; Brauze, Tomasz; Hetmański, Tomasz; Martyka, Rafał; Indykiewicz, Piotr; Myczko, Łukasz; Kunysz, Przemysław; Kawa, Piotr; Czyż, Stanisław; Czechowski, Paweł; Polakowski, Michał; Zduniak, Piotr; Jerzak, Leszek; Janiszewski, Tomasz; Goławski, Artur; Duduś, Leszek; Nowakowski, Jacek J; Wuczyński, Andrzej; Wysocki, Dariusz

    2015-10-01

    Bird feeding is one of the most widespread direct interactions between man and nature, and this has important social and environmental consequences. However, this activity can differ between rural and urban habitats, due to inter alia habitat structure, human behaviour and the composition of wintering bird communities. We counted birds in 156 squares (0.25 km(2) each) in December 2012 and again in January 2013 in locations in and around 26 towns and cities across Poland (in each urban area, we surveyed 3 squares and also 3 squares in nearby rural areas). At each count, we noted the number of bird feeders, the number of bird feeders with food, the type of feeders, additional food supplies potentially available for birds (bread offered by people, bins) and finally the birds themselves. In winter, urban and rural areas differ in the availability of food offered intentionally and unintentionally to birds by humans. Both types of food availability are higher in urban areas. Our findings suggest that different types of bird feeder support only those species specialized for that particular food type and this relationship is similar in urban and rural areas.

  18. 47 CFR 25.147 - Licensing provision for NGSO MSS feeder downlinks in the band 6700-6875 MHz.

    Science.gov (United States)

    2010-10-01

    ... 47 Telecommunication 2 2010-10-01 2010-10-01 false Licensing provision for NGSO MSS feeder downlinks in the band 6700-6875 MHz. 25.147 Section 25.147 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) COMMON CARRIER SERVICES SATELLITE COMMUNICATIONS Applications and Licenses Space Stations § 25.147 Licensing provision for NGSO MSS...

  19. Breaking Rules – Making Bonds

    Indian Academy of Sciences (India)

    IAS Admin

    RESONANCE | January 2016. GENERAL | ARTICLE. Breaking Rules – Making Bonds. A G Samuelson. Boron-containing molecules discovered recently have new types of dative bonds between carbenes and borylenes. At the same time, they show that traditional thumb rules regarding acids and bases are no longer valid.

  20. Oil prices: Breaks and trends

    International Nuclear Information System (INIS)

    Noguera, José

    2013-01-01

    This paper contributes to the literature of the stationarity of financial time series and the literature on oil and macroeconomics in several ways. First, it uses Kejriwal and Perron (2010) sequential procedure to endogenously determine multiple structural changes in real oil prices without facing the circular testing problem between structural changes and stationary assumptions of previous tests. Second, it performs a diagnostic check to detect the significance and magnitude of the potential breaks. Third, it uses the above information to test for the existence of stochastic trends in real oil prices, and fourth, it speculates about possible explanations for the break dates found in order to encourage further work and discussions. The exercise uses monthly data from January 1861 to August 2011. - Highlights: ► The model endogenously determine multiple structural changes in real oil prices. ► The methods used does not face the circular testing problem. ► It also detect the significance and magnitude of the breaks detected. ► It tests for the existence of stochastic trends. ► It explains the reasons for the break dates found

  1. Breaking Bad News to Parents.

    Science.gov (United States)

    Miller, Susan A.

    1996-01-01

    Discusses the difficulty of breaking bad news to parents, whether the news pertains to center policy or a child's behavior. Provides strategies for presenting news and for helping parents to overcome difficult situations, including gathering facts in advance, arranging an appropriate time, and having resource materials available for parents. (MOK)

  2. Inflationary implications of supersymmetry breaking

    NARCIS (Netherlands)

    Borghese, Andrea; Roest, Diederik; Zavala, Ivonne

    2013-01-01

    We discuss a general bound on the possibility to realise inflation in any minimal supergravity with F-terms. The derivation crucially depends on the sGoldstini, the scalar field directions that are singled out by spontaneous supersymmetry breaking. The resulting bound involves both slow-roll

  3. Code breaking in the pacific

    CERN Document Server

    Donovan, Peter

    2014-01-01

    Covers the historical context and the evolution of the technically complex Allied Signals Intelligence (Sigint) activity against Japan from 1920 to 1945 Describes, explains and analyzes the code breaking techniques developed during the war in the Pacific Exposes the blunders (in code construction and use) made by the Japanese Navy that led to significant US Naval victories

  4. Aluminum break-point contacts

    NARCIS (Netherlands)

    Heinemann, Martina; Groot, R.A. de

    1997-01-01

    Ab initio molecular dynamics is used to study the contribution of a single Al atom to an aluminum breakpoint contact during the final stages of breaking and the initial stages of the formation of such a contact. A hysteresis effect is found in excellent agreement with experiment and the form of the

  5. Breaking Rules–Making Bonds

    Indian Academy of Sciences (India)

    Home; Journals; Resonance – Journal of Science Education; Volume 21; Issue 1. Breaking Rules - Making Bonds. A G Samuelson. General Article Volume 21 Issue 1 January 2016 pp 43- ... Author Affiliations. A G Samuelson1. Department of Inorganic and Physical Chemistry, Indian Institute of Science, Bengaluru 560 012 ...

  6. Sediment transport under breaking waves

    DEFF Research Database (Denmark)

    Christensen, Erik Damgaard; Hjelmager Jensen, Jacob; Mayer, Stefan

    2000-01-01

    generated at the surface where the wave breaks as well as the turbulence generated near the bed due to the wave-motion and the undertow. In general, the levels of turbulent kinetic energy are found to be higher than experiments show. This results in an over prediction of the sediment transport. Nevertheless...

  7. Tight bounds for break minimization

    NARCIS (Netherlands)

    Brouwer, Andries E.; Post, Gerhard F.; Woeginger, Gerhard

    We consider round-robin sports tournaments with n teams and n − 1 rounds. We construct an infinite family of opponent schedules for which every home-away assignment induces at least 1/4 n(n−2) breaks. This construction establishes a matching lower bound for a corresponding upper bound from the

  8. supersymmetry breaking with extra dimensions

    Indian Academy of Sciences (India)

    mechanism for (super)symmetry breaking, proposed first by Scherk and Schwarz, where extra dimensions play a crucial role. The last part is devoted to the description of some recent results and of some open problems. Keywords. Supersymmetry; supergravity; extra dimensions. PACS Nos 11.25.Мj; 11.25.Wx; 11.25.

  9. Breaking Carbon Lock-in

    DEFF Research Database (Denmark)

    Driscoll, Patrick Arthur

    2014-01-01

    This central focus of this paper is to highlight the ways in which path dependencies and increasing returns (network effects) serve to reinforce carbon lock-in in large-scale road transportation infrastructure projects. Breaking carbon lock-in requires drastic changes in the way we plan future...

  10. Parental Break-Ups and Stress

    DEFF Research Database (Denmark)

    Dissing, Agnete S.; Dich, Nadya; Nybo Andersen, Anne-Marie

    2017-01-01

    Background: Parental break-up is wide spread, and the effects of parental break-up on children’s well-being are known. The evidence regarding child age at break-up and subsequent family arrangements is inconclusive. Aim: to estimate the effects of parental break-up on stress in pre-adolescent chi......Background: Parental break-up is wide spread, and the effects of parental break-up on children’s well-being are known. The evidence regarding child age at break-up and subsequent family arrangements is inconclusive. Aim: to estimate the effects of parental break-up on stress in pre......-adolescent children with a specific focus on age at break-up and post-breakup family arrangements. Methods: We used data from the Danish National Birth Cohort. Participants included 44 509 children followed from birth to age 11. Stress was self-reported by children at age 11, when the children also reported...... on parental break-up and post break-up family arrangements. Results: Twenty-one percent of the children had experienced a parental break-up at age 11, and those who had experienced parental break-up showed a higher risk of stress (OR:1.72, 95%CI:1.55;1.91) regardless of the child’s age at break-up. Children...

  11. Effect of artificial feeders on pollen loads of the hummingbirds of Cerro de La Muerte, Costa Rica

    Directory of Open Access Journals (Sweden)

    Gerardo Avalos

    2012-03-01

    Full Text Available Although sugar-water feeders are commonly used by enthusiasts to attract hummingbirds, little is known about how they affect hummingbird behavior and flower use. We studied the highland hummingbird assemblage of Cerro de La Muerte, Costa Rica, both at a site with permanent feeders (La Georgina Restaurant and further from it. We examined how feeder use and monopolization affected seasonal changes in pollen loads during four sampling periods, including dry and wet seasons, from 2003-2005. We expected that species monopolizing the feeders would carry little or no pollen whatsoever, and would have pollen loads characterized by low floral diversity, in contrast with species less dependent on feeders. We obtained pollen samples from 183 individuals of four hummingbird species captured around the feeders using mist nets, which were compared with a pollen reference collection of plants with a pollination syndrome by hummingbirds. The same methods were implemented at a site 3km away from the feeders. Feeder usage was quantified by counting the number of times hummingbirds drank from the feeders in periods of 4min separated by 1min. The effects of hummingbird species and season on pollen load categories were assessed using a nominal logistic regression. The alpha species at the site, the Fiery-throated Hummingbird (Panterpe insignis, dominated the feeders during the dry season. Meanwhile, in the wet season, feeder usage was more evenly distributed across species, with the exception of the Volcano Hummingbird, Selasphorus flammula, which occupies the last place in the dominance hierarchy. Pollen loads of hummingbirds captured near feeders were low in abundance (more than 50% of captured individuals had zero or low pollen loads, and low in species richness (96% of the hummingbirds with pollen from only one plant genus, Centropogon. Overall pollen loads increased during the dry season coinciding with peaks in flower availability, although the majority of

  12. A model of intrinsic symmetry breaking

    International Nuclear Information System (INIS)

    Ge, Li; Li, Sheng; George, Thomas F.; Sun, Xin

    2013-01-01

    Different from the symmetry breaking associated with a phase transition, which occurs when the controlling parameter is manipulated across a critical point, the symmetry breaking presented in this Letter does not need parameter manipulation. Instead, the system itself suddenly undergoes symmetry breaking at a certain time during its evolution, which is intrinsic symmetry breaking. Through a polymer model, it is revealed that the origin of the intrinsic symmetry breaking is nonlinearity, which produces instability at the instance when the evolution crosses an inflexion point, where this instability breaks the original symmetry

  13. Stagnation of histopathological improvement is a predictor of hepatocellular carcinoma development after hepatitis C virus eradication.

    Science.gov (United States)

    Motoyama, Hiroyuki; Tamori, Akihiro; Kubo, Shoji; Uchida-Kobayashi, Sawako; Takemura, Shigekazu; Tanaka, Shogo; Ohfuji, Satoko; Teranishi, Yuga; Kozuka, Ritsuzo; Kawamura, Etsushi; Hagihara, Atsushi; Morikawa, Hiroyasu; Enomoto, Masaru; Murakami, Yoshiki; Kawada, Norifumi

    2018-01-01

    Hepatocellular carcinoma (HCC) develops in some patients who achieve sustained virological response (SVR) against hepatitis C virus (HCV) infection via anti-HCV therapy. To examine the pathogenesis of HCC development after HCV eradication, histopathological changes and clinical markers were evaluated in SVR patients. Of 654 SVR patients treated with interferon (IFN)-based therapies, 34 patients who had undergone liver biopsy before initiating IFN therapy and after SVR achievement were enrolled: 11 patients with HCC and 23 patients without HCC (male/female, 9/2 and 8/15, respectively: age, 58 ± 5 and 54 ± 11 years, respectively). We compared the clinical and histopathological factors between the two groups. Immunohistochemistry for Cytoglobin (CYGB) and α smooth muscle actin (α-SMA) was also performed. At baseline, prior to initiating the IFN-based therapy, there were significant differences between the SVR-non-HCC and SVR-HCC groups in the male gender, HBc antibody positivity, prothrombin activity, and histological inflammatory grade. Histopathological evaluation, using the new Inuyama classification system, revealed an improvement in the inflammatory grade, from 2.1 ± 0.6 to 1.0 ± 0.6 (p < 0.0001), whereas the fibrosis stage remained unchanged, from 2.3 ± 0.9 to 2.0 ± 1.2 (p = 0.2749), during the 97 ± 72-month observation period in the SVR-HCC group. Both the grade and stage scores were significantly improved in the SVR-non-HCC group. The area of collagen deposition, evaluated using Sirius red staining, showed a marked decrease, from 18.6 ± 7.6% to 7.7 ± 4.6%, in the SVR-non-HCC group, with no change in the SVR-HCC group. CYGB- and α-SMA-positive hepatic stellate cells (HSCs), indicative of the HSC activated phenotype, remained in the fibrotic tissue of livers among patients in the SVR-HCC group. Stagnation of fibrosis regression is associated with a high risk for HCC after SVR. HSC activation may inhibit improvement in fibrosis after SVR and

  14. Flame stabilization and mixing characteristics in a Stagnation Point Reverse Flow combustor

    Science.gov (United States)

    Bobba, Mohan K.

    A novel combustor design, referred to as the Stagnation Point Reverse-Flow (SPRF) combustor, was recently developed that is able to operate stably at very lean fuel-air mixtures and with low NOx emissions even when the fuel and air are not premixed before entering the combustor. The primary objective of this work is to elucidate the underlying physics behind the excellent stability and emissions performance of the SPRF combustor. The approach is to experimentally characterize velocities, species mixing, heat release and flame structure in an atmospheric pressure SPRF combustor with the help of various optical diagnostic techniques: OH PLIF, chemiluminescence imaging, PIV and Spontaneous Raman Scattering. Results indicate that the combustor is primarily stabilized in a region downstream of the injector that is characterized by low average velocities and high turbulence levels; this is also the region where most of the heat release occurs. High turbulence levels in the shear layer lead to increased product entrainment levels, elevating the reaction rates and thereby enhancing the combustor stability. The effect of product entrainment on chemical timescales and the flame structure is illustrated with simple reactor models. Although reactants are found to burn in a highly preheated (1300 K) and turbulent environment due to mixing with hot product gases, the residence times are sufficiently long compared to the ignition timescales such that the reactants do not autoignite. Turbulent flame structure analysis indicates that the flame is primarily in the thin reaction zones regime throughout the combustor, and it tends to become more flamelet like with increasing distance from the injector. Fuel-air mixing measurements in case of non-premixed operation indicate that the fuel is shielded from hot products until it is fully mixed with air, providing nearly premixed performance without the safety issues associated with premixing. The reduction in NOx emissions in the SPRF

  15. Field evaluation of cutter and feeder mechanism of chickpea harvester for lentil harvesting

    Directory of Open Access Journals (Sweden)

    S Kamgar

    2016-09-01

    Full Text Available Introduction The main producers of lentil are Canada, India, Nepal and China, respectively and Iran is the ninth producer in the world. The hand pulling is the usual method of lentil harvesting. Use of conventional combine because of short leg varieties, wide combine head in dry land and grain losses by cutter bar vibrations is impossible. So a mechanism should be designed to harvest the lentil plants with minimum damage. This mechanism should be evaluated under different tests of crop and machines such as forward speed (FS, grain moisture content (GMC, different varieties and other parameters. Some researchers studied the effects of GMC (Andrews and et al., 1993; Huitink, 2005; Adisa, 2009; Abdi and Jalali, 2013 and FS on grain losses (Geng et al., 1984; Swapan et al., 2001; Mostafavand and Kamgar, 2014; Hunt, 1995. Field tests were conducted at three levels of FS 1.5, 3 and 4.5 km.h-1; three levels of cutting height (CH 4, 8 and 13 cm and two levels of GMC, 8 and 14% on two varieties of lentils including Flip and Shiraz with three replications. Materials and Methods The feeder and cutter mechanism for chickpea harvesting that was the base design of device which is notched wheel and counter shear, was used. The other components of device were dividers, slat and chain feeders, belt and pulleys, chassis, elevator conveyor and storage. Two split plot design based on a randomized complete design was used to determine the effects of above treatments on lentil losses. Results and Discussion The ANOVA results indicated that the all studied factors; FS of feeder and cutter mechanism, CH and GMC had significant effect on losses of Shiraz variety (P0.05. The ranges of losses of Flip variety at 8% GMC were 8.6 to 10% for FS of 1.5 km.h-1, 9.1 to 10.4% for FS of 3 km.h-1and 10.4 to 11.4% for FS of 4.5 km h-1. These ranges at 14% GMC were 7.9 to 8.9% for FS of 1.5 km.h-1, 8.4 to 9.2% for FS of 3 km.h-1and 8.5 to 10% for FS of 4.5 km h-1. The ranges of

  16. Post accidental small breaks analysis

    International Nuclear Information System (INIS)

    Depond, G.; Gandrille, J.

    1980-04-01

    EDF ordered to FRAMATOME by 1977 to complete post accidental long term studies on 'First Contrat-Programme' reactors, in order to demonstrate the safety criteria long term compliance, to get information on NSSS behaviour and to improve the post accidental procedures. Convenient analytical models were needed and EDF and FRAMATOME respectively developped the AXEL and FRARELAP codes. The main results of these studies is that for the smallest breaks, it is possible to manually undertake cooling and pressure reducing actions by dumping the steam generators secondary side in order to meet the RHR operating specifications and perform long term cooling through this system. A specific small breaks procedure was written on this basis. The EDF and FRAMATOME codes are continuously improved; the results of a French set of separate effects experiments will be incorporated as well as integral system verification

  17. Prophylactic treatment of retinal breaks

    DEFF Research Database (Denmark)

    Blindbæk, Søren Leer; Grauslund, Jakob

    2015-01-01

    Prophylactic treatment of retinal breaks has been examined in several studies and reviews, but so far, no studies have successfully applied a systematic approach. In the present systematic review, we examined the need of follow-up after posterior vitreous detachment (PVD) - diagnosed by slit...... published before 2012. Four levels of screening identified 13 studies suitable for inclusion in this systematic review. No meta-analysis was conducted as no data suitable for statistical analysis were identified. In total, the initial examination after symptomatic PVD identified 85-95% of subsequent retinal......-47% of cases, respectively. The cumulated incidence of RRD despite prophylactic treatment was 2.1-8.8%. The findings in this review suggest that follow-up after symptomatic PVD is only necessary in cases of incomplete retinal examination at presentation. Prophylactic treatment of symptomatic retinal breaks...

  18. Breaking through the tranfer tunnel

    CERN Document Server

    Laurent Guiraud

    2001-01-01

    This image shows the tunnel boring machine breaking through the transfer tunnel into the LHC tunnel. Proton beams will be transferred from the SPS pre-accelerator to the LHC at 450 GeV through two specially constructed transfer tunnels. From left to right: LHC Project Director, Lyn Evans; CERN Director-General (at the time), Luciano Maiani, and Director for Accelerators, Kurt Hubner.

  19. Models of electroweak symmetry breaking

    CERN Document Server

    Pomarol, Alex

    2015-01-01

    This chapter present models of electroweak symmetry breaking arising from strongly interacting sectors, including both Higgsless models and mechanisms involving a composite Higgs. These scenarios have also been investigated in the framework of five-dimensional warped models that, according to the AdS/CFT correspondence, have a four-dimensional holographic interpretation in terms of strongly coupled field theories. We explore the implications of these models at the LHC.

  20. Supersymmetry breaking at finite temperature

    International Nuclear Information System (INIS)

    Kratzert, K.

    2002-11-01

    The mechanism of supersymmetry breaking at finite temperature is still only partly understood. Though it has been proven that temperature always breaks supersymmetry, the spontaneous nature of this breaking remains unclear, in particular the role of the Goldstone fermion. The aim of this work is to unify two existing approaches to the subject. From a hydrodynamic point of view, it has been argued under very general assumptions that in any supersymmetric quantum field theory at finite temperature there should exist a massless fermionic collective excitation, named phonino because of the analogy to the phonon. In the framework of a self-consistent resummed perturbation theory, it is shown for the example of the Wess-Zumino model that this mode fits very well into the quantum field theoretical framework pursued by earlier works. Interpreted as a bound state of boson and fermion, it contributes to the supersymmetric Ward-Takahashi identities in a way showing that supersymmetry is indeed broken spontaneously with the phonino playing the role of the Goldstone fermion. The second part of the work addresses the case of supersymmetric quantum electrodynamics. It is shown that also here the phonino exists and must be interpreted as the Goldstone mode. This knowledge allows a generalization to a wider class of models. (orig.)

  1. On the preparation of fire-wood splitting machines equipped with feeder devices

    International Nuclear Information System (INIS)

    Jaeaeskelaeinen, M.

    1995-01-01

    As part of the Bionergy research programme, the TTS Institute's Department of Forestry conducted a study on firewood splitting machines manufactured by Bilke Oy and Peurala Oy. The said machines are the first of their kind in Finland to be equipped with a feeder device. The Bilke unit is fed by a conveyor belt arrangement while the Peurala unit is equipped with a feeder roll. In addition, both machine types are equipped with a conveyor belt discharging device (e.g. for discharging split wood directly into a trailer). The Bilke unit can also be operated on extraction racks in the woods as the stems due to be split are fed into it from the side and the conveyor discharges the split wood rearwards into the trailer. The trailer can be hooked onto the splitting unit's draw-hook. At the landing, the Bilke unit was used to split a total of 14.2 m 3 and the Peurala unit 8.0 m 3 of approx. 3-metrelong stems averaging 9 cm in diameter. In addition to this, the Bilke unit was used to split ca. 17 m 3 of 3.5 metre-long stems with on average diameter of ca. 6 cm; the stems were in bunches alongside the extraction racks. The person operating the machines for the purposes of this study was a 27-year- old forest worker. The mean productivity achieved at the landing when using the Bilke unit was 7.7 m 3 while that of the Peurala unit was 5.8 m 3 per effective hour. When operated in the woods, the productivity achieved with the Bilke unit (excluding felling-cross cutting-delimbing-bunching and forest haulage work) was 2.8 m 3 /h. When applying a productivity of 1.7 m 3 for felling-cross cutting- delimbing-bunching work and 5.5. m 3 for forest haulage, the entire harvesting chain's productivity was 0.9 m 3 per effective hour

  2. Using automated feeders to wean calves fed large amounts of milk according to their ability to eat solid feed.

    Science.gov (United States)

    de Passillé, Anne Marie; Rushen, Jeffrey

    2016-05-01

    Dairy calves weaned off milk at an early age show signs of hunger and can lose weight. We examined whether using automated feeders to wean calves according to individual voluntary solid feed intake reduced the effects of weaning. Female Holstein calves were housed in groups of 5 to 9. All calves were fed 12 L/d milk and ad libitum grain starter and hay from automated feeders immediately after grouping, and were allocated to 3 weaning strategies: (1) early-weaned (EW; n=14): weaning began on d 40, and milk allowance gradually decreased until weaning was complete on d 48; (2) late-weaned (LW; n=14): weaning began on d 80 and was completed on d 89; (3) weaned by starter intake (WSI; n=28): weaning began when calves consumed 200g/d of starter and was completed when the calves consumed 1,400g/d. Each day, the automated feeders recorded quantities of milk, starter, and hay eaten by all calves, as well as the frequency of visits to the milk feeder; we used unrewarded visit frequency as a sign of hunger. Body weights (BW) were recorded weekly. We estimated daily digestible energy (DE) intake for each calf based on the milk, hay, and starter consumed. Average daily gains (ADG) were expressed as percent of BW. For calves in WSI, weaning began at 54.7±18.9 d (mean ± SD) of age, the duration of weaning was 21.1±10.6 d, and weaning ended at 75.8±10.7 d of age. Both LW and WSI calves had better ADG from wk 3 to 13 than EW calves. Calves in the WSI group drank less milk and ate more starter than LW calves but had similar ADG. During the period of weaning, EW calves made more unrewarded visits to the milk feeder than LW and WSI calves. Three EW calves lost weight during weaning, whereas all LW and WSI calves gained weight. Calves differ greatly in when they begin to eat solid feed and how quickly they increase the intake in response to a decrease in milk allowance. An advantage of automated feeders is that calves can be weaned at variable ages depending on their ability and

  3. Dynamic breaking of a single gold bond

    DEFF Research Database (Denmark)

    Pobelov, Ilya V.; Lauritzen, Kasper Primdal; Yoshida, Koji

    2017-01-01

    . Conversely, if the force is loaded rapidly it is more likely that the maximum breaking force is measured. Paradoxically, no clear differences in breaking force were observed in experiments on gold nanowires, despite being conducted under very different conditions. Here we explore the breaking behaviour...

  4. The effect of space allowance and cage size on laying hens housed in furnished cages, Part II: Behavior at the feeder

    Science.gov (United States)

    Widowski, T. M; Caston, L. J; Casey-Trott, T. M; Hunniford, M. E

    2017-01-01

    Abstract Standards for feeder (a.k.a. feed trough) space allowance (SA) are based primarily on studies in conventional cages where laying hens tend to eat simultaneously, limiting feeder space. Large furnished cages (FC) offer more total space and opportunities to perform a greater variety of behaviors, which may affect feeding behavior and feeder space requirements. Our objective was to determine the effects of floor/feeder SA on behavior at the feeder. LSL-Lite hens were housed in FC equipped with a nest, perches, and a scratch mat. Hens with SA of either 520 cm2 (Low; 8.9 cm feeder space/hen) or 748 cm2 (High; 12.8 cm feeder space/hen) per bird resulted in groups of 40 vs. 28 birds in small FC (SFC) and 80 vs. 55 in large FC (LFC). Chain feeders ran at 0500, 0800, 1100, 1400, and 1700 with lights on at 0500 and off at 1900 hours. Digital recordings of FC were scanned at chain feeder onset and every 15 min for one h after (5 scans × 5 feeding times × 2 d) to count the number of birds with their head in the feeder. All occurrences of aggressive pecks and displacements during 2 continuous 30-minute observations at 0800 h and 1700 h also were counted. Mixed model repeated analyses tested the effects of SA, cage size, and time on the percent of hens feeding, and the frequency of aggressive pecks and displacements. Surprisingly, the percent of birds feeding simultaneously was similar regardless of cage size (LFC: 23.0 ± 0.9%; SFC: 24.0 ± 1.0%; P = 0.44) or SA (Low: 23.8 ± 0.9%; High: 23.3 ± 1.0%; P = 0.62). More birds were observed feeding at 1700 h (35.3 ± 0.1%) than any at other time (P < 0.001). Feeder use differed by cage area (nest, middle, or scratch) over the d (P < 0.001). The frequency of aggressive pecks was low overall and not affected by SA or cage size. Frequency of displacements was also low but greater at Low SA (P = 0.001). There was little evidence of feeder competition at the Low SA in this study. PMID:29050409

  5. Feeders of free-roaming cats: personal characteristics, feeding practices and data on cat health and welfare in an urban setting of Israel

    Directory of Open Access Journals (Sweden)

    Idit eGunther

    2016-03-01

    Full Text Available Cat feeders serve as an important source of available food for free-roaming cats (FRC and can play a central role in providing data on FRC distribution, welfare, and health. Data on cat feeder personalities as well as a better understanding of their feeding practices offer relevance for decision making concerning FRC population control strategies. The current study surveyed 222 FRC feeders who responded to a municipal trap-neuter-return (TNR campaign in an Israeli central urban setting. The aim of the study was to describe their personal characteristics, feeding practices and the FRC populations they feed. Feeders were divided into four groups according to the number of cats they claimed to feed per day (group 1: fed up to five cats; group 2: fed six to 10 cats; group 3: fed 11-20 cats; group 4: fed ≥21 cats. Most feeders were women (81%, with a median age of 58 years (range 18-81. The feeders reported an overall feeding of 3,337 cats in 342 different feeding locations. Feeders of group 4 comprised of 15.31% (n=34 of all feeders, but fed 56% (n=1869 of the FRC in 37.42% (n=128 of the feeding locations. 'Heavy' feeders (groups 3 and 4 reported that they traveled significantly longer distances in order to feed the cats. Commercial dry food consisted of 90% of the food they provided, with 66% of them feeding once a day, with less food per cat per day than the other feeder groups. Interestingly, 'heavy' feeders were usually singles, had on average fewer siblings, a clear preference for owning cats as pets and lived in lower income neighborhoods. According to the feeders' reports on the FRC populations they fed, 69.7% (2325/3337 cats were neutered and 11.8% (395/3337 were kittens. In addition, they reported that 1.6% (54/3337 of the cats were limping, 2% (67/3337 suffered from a systemic disease, 4% (135/3337 had skin lesions, and 3.9% (130/3337 were suffering from a chronic disability. Abundance of kittens and morbidity rate were significantly and

  6. An experimental study on the influence of water stagnation and temperature change on water quality in a full-scale domestic drinking water system.

    Science.gov (United States)

    Zlatanović, Lj; van der Hoek, J P; Vreeburg, J H G

    2017-10-15

    The drinking water quality changes during the transport through distribution systems. Domestic drinking water systems (DDWSs), which include the plumbing between the water meter and consumer's taps, are the most critical points in which water quality may be affected. In distribution networks, the drinking water temperature and water residence time are regarded as indicators of the drinking water quality. This paper describes an experimental research on the influence of stagnation time and temperature change on drinking water quality in a full-scale DDWS. Two sets of stagnation experiments, during winter and summer months, with various stagnation intervals (up to 168 h of stagnation) were carried out. Water and biofilms were sampled at two different taps, a kitchen and a shower tap. Results from this study indicate that temperature and water stagnation affect both chemical and microbial quality in DDWSs, whereas microbial parameters in stagnant water appear to be driven by the temperature of fresh water. Biofilm formed in the shower pipe contained more total and intact cells than the kitchen pipe biofilm. Alphaproteobacteria were found to dominate in the shower biofilm (78% of all Proteobacteria), while in the kitchen tap biofilm Alphaproteobacteria, Betaproteobacteria and Gammaproteobacteria were evenly distributed. Copyright © 2017 The Authors. Published by Elsevier Ltd.. All rights reserved.

  7. Role Overload, Role Self Distance, Role Stagnation as Determinants of Job Satisfaction and Turnover Intention in Banking Sector

    Science.gov (United States)

    Kunte, Monica; Gupta, Priya; Bhattacharya, Sonali; Neelam, Netra

    2017-01-01

    Purpose: This study examined the relationship of the organizational role stress: Role overload, role self-distance, and role stagnation with job satisfaction and turnover intention with a sample of banking employees in India. Methodology: In this research, we used the RODS scale developed by Prohit and Pareek (2010) for measuring occupational role scale. The reliability of the scale came out to be 0.71. Findings: The majority of employees of all ranks, in both private and public sector banks, suffer from high role stress of all types. It was found that role overload and role stagnation are inversely associated with banking employees' job satisfaction. Private sector bank employees have more role stress and more unsatisfied than employees of public sector banks. Employees Turnover intention was found to be positively impacted by job satisfaction, contrary to many other studies. Possible reasons have been suggested. Job satisfaction was found to play a partial mediating role in the relationship between role overload and turnover intention with 40% mediation. Further, employees with longer tenure (work experience) have less role stress and are more satisfied. Originality: This study is unique in the sense there is hardly any study linking role stress to job satisfaction and turnover intention, specially in Indian context. PMID:29200554

  8. Vaporisation characteristics of methanol, ethanol and heptane droplets in opposed stagnation flow at low temperature and pressure

    Science.gov (United States)

    Zhu, Huayang; Kee, Robert J.; Chen, Longhua; Cao, Jingjing; Xu, Min; Zhang, Yuyin

    2012-08-01

    A computational model is developed and applied to study the vaporisation behaviour of three liquid fuels. This fundamental study is motivated by a need to understand how the performance of direct-injection-spark-ignition (DISI) engines may be affected by changes in fuel composition, especially alcohols. Currently, most DISI engines are designed for homogeneous-charge combustion, where the in-cylinder fuel injection, vaporisation and mixing is accomplished during the intake and early in the compression process. Thus the temperature and pressure are low, compared to post-compression conditions. The two-phase axisymmetric model is based upon an ideal opposed stagnation flow field. Liquid droplets are carried in one air stream that is met by an opposed air flow. Because of stagnation-flow similarity, the mathematical model can be represented as a one-dimensional boundary-value problem. Results show significant differences between methanol, ethanol and heptane fuels, which have potentially important impacts on the design and modification of fuel-injection systems for direct-injection engines with alternative fuels.

  9. Role Overload, Role Self Distance, Role Stagnation as Determinants of Job Satisfaction and Turnover Intention in Banking Sector.

    Science.gov (United States)

    Kunte, Monica; Gupta, Priya; Bhattacharya, Sonali; Neelam, Netra

    2017-01-01

    This study examined the relationship of the organizational role stress: Role overload, role self-distance, and role stagnation with job satisfaction and turnover intention with a sample of banking employees in India. In this research, we used the RODS scale developed by Prohit and Pareek (2010) for measuring occupational role scale. The reliability of the scale came out to be 0.71. The majority of employees of all ranks, in both private and public sector banks, suffer from high role stress of all types. It was found that role overload and role stagnation are inversely associated with banking employees' job satisfaction. Private sector bank employees have more role stress and more unsatisfied than employees of public sector banks. Employees Turnover intention was found to be positively impacted by job satisfaction, contrary to many other studies. Possible reasons have been suggested. Job satisfaction was found to play a partial mediating role in the relationship between role overload and turnover intention with 40% mediation. Further, employees with longer tenure (work experience) have less role stress and are more satisfied. This study is unique in the sense there is hardly any study linking role stress to job satisfaction and turnover intention, specially in Indian context.

  10. The effect of mixing rates on the formation and growth of condensation aerosols in a model stagnation flow

    KAUST Repository

    Alshaarawi, Amjad

    2015-03-01

    A steady, laminar stagnation flow configuration is adopted to investigate numerically the interaction between condensing aerosol particles and gas-phase transport across a canonical mixing layer. The mixing rates are varied by adjusting the velocity and length scales of the stagnation flow parametrically. The effect of mixing rates on particle concentration, polydispersity, and mean droplet diameter is explored and discussed. This numerical study reveals a complex response of the aerosol to varying flow times. Depending on the flow time, the variation of the particle concentration in response to varying mixing rates falls into one of the two regimes. For fast mixing rates, the number density and volume fraction of the condensing particles increase with residence time (nucleation regime). On the contrary, for low mixing rates, number density decreases with residence time and volume fraction reaches a plateau (condensation regime). It is shown that vapor scavenging by the aerosol phase is key to explaining the transition between these two regimes. The results reported here are general and illustrate genuine features of the evolution of aerosols forming by condensation of supersaturated vapor from heat and mass transport across mixing layers.

  11. Standard Practice for Exposure of Solar Collector Cover Materials to Natural Weathering Under Conditions Simulating Stagnation Mode

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    1992-01-01

    1.1 This practice covers a procedure for the exposure of solar collector cover materials to the natural weather environment at elevated temperatures that approximate stagnation conditions in solar collectors having a combined back and edge loss coefficient of less than 1.5 W/(m2 · °C). 1.2 This practice is suitable for exposure of both glass and plastic solar collector cover materials. Provisions are made for exposure of single and double cover assemblies to accommodate the need for exposure of both inner and outer solar collector cover materials. 1.3 This practice does not apply to cover materials for evacuated collectors, photovoltaic cells, flat-plate collectors having a combined back and edge loss coefficient greater than 1.5 W/(m2 ·° C), or flat-plate collectors whose design incorporates means for limiting temperatures during stagnation. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard t...

  12. The effect of residence time on the dynamics of a condensating aerosol in a Hiemenz-type stagnation flow

    Science.gov (United States)

    Alshaarawi, Amjad; Zhou, Kun; Scribano, Gianfranco; Attili, Antonio; Bisetti, Fabrizio; Clean Combustion Research Center Team

    2013-11-01

    The effect of residence time on the formation and growth of a condensating aerosol is simulated in a Hiemenz-type stagnation flow setup, for which a unique and well-defined time scale characterizes the velocity field. In this configuration, a hot stream saturated with dibutyle phthalate (DBP) vapor mixes with a cold dry stream. A mixing layer forms at the stagnation plane triggering supersaturation and droplets are generated by homogeneous nucleation. Aerosol dynamics are simulated using the Quadrature Method of Moments (QMOM). Two regimes related to the flow residence time are observed, i.e., a nucleation regime and a condensation regime. The nucleation regime, at short residence times, is characterized by the consumption of DBP vapor into droplets having a negligible effect on the vapor phase. In this regime, both the number density and volume fraction of droplets increase with residence time. In the condensation regime, at long residence times, vapor condensation consumes the vapor phase considerably. For longer residence times, more vapor is consumed, resulting in lower number densities due to the lower nucleation rates, whereas the volume fraction saturates.

  13. Comparisons of benthic filter feeder communities before and after a large-scale capital dredging program.

    Science.gov (United States)

    Abdul Wahab, Muhammad Azmi; Fromont, Jane; Gomez, Oliver; Fisher, Rebecca; Jones, Ross

    2017-09-15

    Changes in turbidity, sedimentation and light over a two year large scale capital dredging program at Onslow, northwestern Australia, were quantified to assess their effects on filter feeder communities, in particular sponges. Community functional morphological composition was quantified using towed video surveys, while dive surveys allowed for assessments of species composition and chlorophyll content. Onslow is relatively diverse recording 150 sponge species. The area was naturally turbid (1.1 mean P 80 NTU), with inshore sites recording 6.5× higher turbidity than offshore localities, likely influenced by the Ashburton River discharge. Turbidity and sedimentation increased by up to 146% and 240% through dredging respectively, with corresponding decreases in light levels. The effects of dredging was variable, and despite existing caveats (i.e. bleaching event and passing of a cyclone), the persistence of sponges and the absence of a pronounced response post-dredging suggest environmental filtering or passive adaptation acquired pre-dredging may have benefited these communities. Copyright © 2017. Published by Elsevier Ltd.

  14. Real-time modeling and simulation of distribution feeder and distributed resources

    Science.gov (United States)

    Singh, Pawan

    The analysis of the electrical system dates back to the days when analog network analyzers were used. With the advent of digital computers, many programs were written for power-flow and short circuit analysis for the improvement of the electrical system. Real-time computer simulations can answer many what-if scenarios in the existing or the proposed power system. In this thesis, the standard IEEE 13-Node distribution feeder is developed and validated on a real-time platform OPAL-RT. The concept and the challenges of the real-time simulation are studied and addressed. Distributed energy resources include some of the commonly used distributed generation and storage devices like diesel engine, solar photovoltaic array, and battery storage system are modeled and simulated on a real-time platform. A microgrid encompasses a portion of an electric power distribution which is located downstream of the distribution substation. Normally, the microgrid operates in paralleled mode with the grid; however, scheduled or forced isolation can take place. In such conditions, the microgrid must have the ability to operate stably and autonomously. The microgrid can operate in grid connected and islanded mode, both the operating modes are studied in the last chapter. Towards the end, a simple microgrid controller modeled and simulated on the real-time platform is developed for energy management and protection for the microgrid.

  15. Controlling Voltage Levels of Distribution Network-Radial Feeder after Connecting Wind Turbines to the Network

    Directory of Open Access Journals (Sweden)

    Muhammad Al Badri

    2017-11-01

    Full Text Available Several factors in power generation and supply need to be taken into account such as shortages of energy supply, system stability, and energy quality and system disruption due to network losses, industrial development and population expansion. The addition of wind turbines to the distribution network is of great benefit in providing additional power and solving these problems, but this addition is accompanied by the problem of low voltage network. This research found optimal solutions to the problem of low voltage distribution network after connecting wind turbines. The main idea of this paper is to optimize the low-voltage problem as a result of connecting the wind turbines to the "far end" of the radial feeder for a distribution network and to obtain a voltage level within an acceptable and stable range. The problem of low voltage solved by using the load-drop compensation, capacitor-bank and “doubly-fed” induction generators. The results of this study were based on the operation of the entire design of the simulation system which would be compatible with the reality of the energy flow of all network components by using the PSCAD program. The present analysis program revealed an optimum solution for the low voltage profile of the distribution network after connecting the wind turbine.

  16. Power Hardware-in-the-Loop Evaluation of PV Inverter Grid Support on Hawaiian Electric Feeders: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Nelson, Austin; Prabakar, Kumaraguru; Nagarajan, Adarsh; Nepal, Shaili; Hoke, Anderson; Asano, Marc; Ueda, Reid; Ifuku, Earle

    2017-05-08

    As more grid-connected photovoltaic (PV) inverters become compliant with evolving interconnections requirements, there is increased interest from utilities in understanding how to best deploy advanced grid-support functions (GSF) in the field. One efficient and cost-effective method to examine such deployment options is to leverage power hardware-in-the-loop (PHIL) testing methods. Two Hawaiian Electric feeder models were converted to real-time models in the OPAL-RT real-time digital testing platform, and integrated with models of GSF capable PV inverters that were modeled from characterization test data. The integrated model was subsequently used in PHIL testing to evaluate the effects of different fixed power factor and volt-watt control settings on voltage regulation of the selected feeders. The results of this study were provided as inputs for field deployment and technical interconnection requirements for grid-connected PV inverters on the Hawaiian Islands.

  17. A Double-Resistive Active Power Filter System to Attenuate Harmonic Voltages of a Radial Power Distribution Feeder

    DEFF Research Database (Denmark)

    Sun, Xiaofeng; Han, Ruijing; Shen, Hong

    2016-01-01

    Harmonic propagation between power-factor correction capacitors and system inductors seriously deteriorates power quality in a radial power distribution feeder. Installation of a resistive active power filter (RAPF) at the end bus only suppresses harmonic propagation, not attenuates harmonic...... voltages. This paper proposes a double-resistive active power filter (D-RAPF) system consisting of a terminal-RAPF and an attenuation-RAPF for each individual harmonic. The terminal-RAPF operating as the characteristic impedance of the feeder is installed at the end bus to suppress harmonic propagation...... harmonic propagation and attenuates harmonic voltages more effectively, but also has the same rated power capacity as the RAPF. However, both the harmonic damping performance and the rated power capacity must be considered to choose the D-RAPF system or the RAPF when a harmonic current source exists...

  18. Utilisation of symmetrical components in a communication-based protection for loop MV feeders with variable short-circuit power

    DEFF Research Database (Denmark)

    Ciontea, Catalin-Iosif; Bak, Claus Leth; Blaabjerg, Frede

    2018-01-01

    Variability of the available short-circuit power also implies variation of the fault level, which can potentially cause several protection problems in the electric networks. In this paper, a novel protection method that is insensitive to the fault level changes caused by variable short......-circuit power is presented. It relies on utilisation of symmetrical components of the short-circuit currents and on communication between the protection relays. The proposed method addresses the Single Phase to Ground (SPG) faults occurring in directly grounded distribution networks, with focus on closed......-loop Medium Voltage (MV) feeders. Case studies are presented, which demonstrate that the proposed protection scheme is capable of effectively detecting the SPG faults in closed-loop feeders with variable short-circuit power....

  19. Short communication: Milk meal pattern of dairy calves is affected by computer-controlled milk feeder set-up

    DEFF Research Database (Denmark)

    Jensen, Margit Bak

    2009-01-01

    Ninety-six calves housed in groups of 8 were fed either a high milk allowance (heavy breeds 9.6 L/d; Jerseys 7.2 L/d) or a low milk allowance (heavy breeds 4.8 L/d; Jerseys 3.6 L/d) via a computer-controlled milk feeder. Half of the calves on each allowance could ingest the milk in 2 or more dail...

  20. Inflationary implications of supersymmetry breaking

    Energy Technology Data Exchange (ETDEWEB)

    Borghese, Andrea; Roest, Diederik; Zavala, Ivonne [Centre for Theoretical Physics, University of Groningen, Nijenborgh 4, 9747 AG Groningen (Netherlands)

    2013-07-23

    We discuss a general bound on the possibility to realise inflation in any minimal supergravity with F-terms. The derivation crucially depends on the sGoldstini, the scalar field directions that are singled out by spontaneous supersymmetry breaking. The resulting bound involves both slow-roll parameters and the geometry of the Kähler manifold of the chiral scalars. We analyse the inflationary implications of this bound, and in particular discuss to what extent the requirements of single field and slow-roll can both be met in F-term inflation.

  1. Leaders break ground for INFINITY

    Science.gov (United States)

    2008-01-01

    Community leaders from Mississippi and Louisiana break ground for the new INFINITY at NASA Stennis Space Center facility during a Nov. 20 ceremony. Groundbreaking participants included (l to r): Gottfried Construction representative John Smith, Mississippi Highway Commissioner Wayne Brown, INFINITY board member and Apollo 13 astronaut Fred Haise, Stennis Director Gene Goldman, Studio South representative David Hardy, Leo Seal Jr. family representative Virginia Wagner, Hancock Bank President George Schloegel, Mississippi Rep. J.P. Compretta, Mississippi Band of Choctaw Indians representative Charlie Benn and Louisiana Sen. A.G. Crowe.

  2. Effects of Home Energy Management Systems on Distribution Utilities and Feeders Under Various Market Structure; NREL (National Renewable Energy Laboratory)

    Energy Technology Data Exchange (ETDEWEB)

    Ruth, M.; Pratt, A.; Lunacek, M.; Mittal, S.; Wu, H.; Jones, W.

    2015-06-15

    The combination of distributed energy resources (DER) and retail tariff structures to provide benefits to both utility consumers and the utilities is not well understood. To improve understanding, an Integrated Energy System Model (IESM) is being developed to simulate the physical and economic aspects of DER technologies, the buildings where they reside, and feeders servicing them. The IESM was used to simulate 20 houses with home energy management systems on a single feeder under a time-of-use (TOU) tariff to estimate economic and physical impacts on both the households and the distribution utilities. Home energy management systems (HEMS) reduce consumers’ electric bills by precooling houses in the hours before peak electricity pricing. Utilization of HEMS reduce peak loads during high price hours but shifts it to hours with off-peak and shoulder prices, resulting in a higher peak load. used to simulate 20 houses with home energy management systems on a single feeder under a time-of-use (TOU) tariff to estimate economic and physical impacts on both the households and the distribution utilities. Home energy management systems (HEMS) reduce consumers’ electric bills by precooling houses in the hours before peak electricity pricing. Utilization of HEMS reduce peak loads during high price hours but shifts it to hours with off-peak and shoulder prices, resulting in a higher peak load.

  3. Optimal distribution feeder reconfiguration for increasing the penetration of plug-in electric vehicles and minimizing network costs

    International Nuclear Information System (INIS)

    Kavousi-Fard, Abdollah; Abbasi, Alireza; Rostami, Mohammad-Amin; Khosravi, Abbas

    2015-01-01

    Appearance of PEVs (Plug-in Electric Vehicles) in future transportation sector brings forward opportunities and challenges from grid perspective. Increased utilization of PEVs will result in problems such as greater total loss, unbalanced load factor, feeder congestion and voltage drop. PEVs are mobile energy storages dispersed all over the network with benefits to both owners and utilities in case of V2G (Vehicle-to-Grid) possibility. The intelligent bidirectional power flow between grid and large number of vehicles adds complexity to the system and requires operative tools to schedule V2G energy and subdue PEV impacts. In this paper, DFR (Distribution Feeder Reconfiguration) is utilized to optimally coordinate PEV operation in a stochastic framework. Uncertainty in PEVs characteristics can be due to several sources from location and time of grid connection to driving pattern and battery SoC (State-of-Charge). The proposed stochastic problem is solved with a self-adaptive evolutionary swarm algorithm based on SSO (Social Spider Optimization) algorithm. Numerical studies verify the efficacy of the proposed DFR to improve the system performance and optimal dispatch of V2G. - Highlights: • Consideration effect of PEVS on the distribution feeder reconfiguration. • Increasing the penetration of PEVS. • Introducing a new artificial optimization algorithm. • Modeling the uncertainty in network. • Investigating the degradation cost of batteries in V2G technology.

  4. A novel coal feeder for production of low sulfur fuel. Annual technical progress report, October 1, 1990--October 1, 1991

    Energy Technology Data Exchange (ETDEWEB)

    Khang, S.J.; Lin, L.; Keener, T.C.; Yeh, P.

    1991-12-31

    A dual-screw feeder was designed for desulfurization of coal. This reactor contains two screw tubes, the inner tube acting as a coal pyrolizer and the outer tube acting as a desulfurizer with hot calcined lime pellets or other renewable sorbent pellets. The objectives of this project is to study the feasibility of an advanced concept of desulfurization and possibly some denitrification in this coal feeder. In this year, two basic studies have been performed: (1) the desulfurization and (2) the denitrification due to mild pyrolysis. Specifically, the following tasks have been performed: (1) Setting up the Dual-Screw reactor, (2) Determination of the pyrolysis product and the sulfur distribution in char, tar and gas based on experimental data, (3) Study of the devolatilization, the desulfurization kinetics and the denitrification kinetics and obtaining the basic kinetic parameters, (4) Study of the sulfur removal efficiency of lime pellets fed into the outer tube of the dual-feeder reactor, (5) Study of the effect of the coal particle size on pyrolysis and desulfurization, (6) Study of the coal pyrolysis and desulfurization using a TGA(Thermal Gravimetric Analyzer).

  5. Diversity in mixed species groups improves success in a novel feeder test in a wild songbird community

    Science.gov (United States)

    Freeberg, Todd M.; Eppert, Shannon K.; Sieving, Kathryn E.; Lucas, Jeffrey R.

    2017-01-01

    Mixed-species groups are common and are thought to provide benefits to group members via enhanced food finding and antipredator abilities. These benefits could accrue due to larger group sizes in general but also to the diverse species composition in the groups. We tested these possibilities using a novel feeder test in a wild songbird community containing three species that varied in their dominant-subordinate status and in their nuclear-satellite roles: Carolina chickadees (Poecile carolinensis), tufted titmice (Baeolophus bicolor), and white-breasted nuthatches (Sitta carolinensis). We found that chickadees and titmice were more likely to obtain seed from the novel feeder with greater diversity of species composition in their mixed-species flocks. For successful chickadee flocks, furthermore, the latency to obtain seed from the novel feeder was shorter the more diverse their flocks were. These results in a natural setting indicate that diversity, per se, can benefit individuals in mixed-species groups in biologically meaningful contexts such as finding food in novel places. PMID:28230159

  6. Water quality in Pearl Harbor and feeder streams during 1971 - 2001 collected primarily by oceanography students from Leeward Community College (NODC Accession 0000590)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Water quality data were collected in Pearl Harbor and surrounding feeder streams from 30 December 1971 to 24 August 2001. Data were collected by Leeward Community...

  7. The Price and Progress of Compliance with Federal Financial Management Reporting Requirements in Department of the Navy Property, Plant, and Equipment Nonfinancial Feeder Systems

    National Research Council Canada - National Science Library

    Burks, Michael

    2000-01-01

    .... The Department of Defense (DOD) remains the predominant noncompliant agency, and in 1999 acknowledged that archaic data feeder systems never intended to comply with accounting standards or integrate with financial management...

  8. A Multistate Investigation of Antibiotic-Resistant Salmonella enterica Serotype I 4,[5],12:i:- Infections as Part of an International Outbreak Associated with Frozen Feeder Rodents.

    Science.gov (United States)

    Cartwright, E J; Nguyen, T; Melluso, C; Ayers, T; Lane, C; Hodges, A; Li, X; Quammen, J; Yendell, S J; Adams, J; Mitchell, J; Rickert, R; Klos, R; Williams, I T; Barton Behravesh, C; Wright, J

    2016-02-01

    While most human Salmonella infections result from exposure to contaminated foods, an estimated 11% of all Salmonella infections are attributed to animal exposures, including both direct animal handling and indirect exposures such as cleaning cages and handling contaminated pet food. This report describes the epidemiologic, environmental and laboratory investigations conducted in the United States as part of the response to an international outbreak of tetracycline-resistant Salmonella enterica serotype I 4,[5],12:i:- infections with over 500 illnesses occurring from 2008 to 2010. This investigation found that illness due to the outbreak strain was significantly associated with exposure to pet reptiles and frozen feeder rodents used as food for pet reptiles. Salmonella isolates indistinguishable from the outbreak strain were isolated from a frozen feeder mice-fed reptile owned by a case patient, as well as from frozen feeder mice and environmental samples collected from a rodent producing facility (Company A). An international voluntary recall of all Company A produced frozen feeder animals sold between May 2009 and July 2010 occurred. Only 13% of cases in our investigation were aware of the association between Salmonella infection and mice or rats. Consumers, the pet industry, healthcare providers and veterinarians need to be aware of the potential health risk posed by feeder rodents, whether live or frozen. Frozen feeder rodent producers, suppliers and distributors should follow the animal food labelling requirements as described in 21 CFR §501.5, and all packages of frozen feeder rodents should include safe handling instructions. Persons should wash their hands thoroughly with soap and water after handling live or frozen feeder rodents, as well as reptiles or anything in the area where the animals live. Continued opportunities exist for public health officials, the pet industry, veterinarians and consumers to work together to prevent salmonellosis associated

  9. Effect of portion size and milk flow on the use of a milk feeder and the development of cross-sucking in dairy calves

    DEFF Research Database (Denmark)

    Nielsen, Per Peetz; Jensen, Margit Bak; Halekoh, Ulrich

    2018-01-01

    This study aimed to investigate whether reducing the milk flow and increasing the milk portion size of a computer-controlled milk feeder would lead to less cross-sucking and fewer unrewarded feeder visits in dairy calves. Five groups, each with 9 or 10 calves (n = 48), were housed in pens with on...... to cross-sucking more often than heifers, while heifer calves initiated more cross-sucking than bulls warrants further studies on these gender effects....

  10. Adjusting the weaning age of calves fed by automated feeders according to individual intakes of solid feed.

    Science.gov (United States)

    de Passillé, A M; Rushen, J

    2012-09-01

    When weaned at the ages typical of commercial dairy production, dairy calves usually show reduced growth rates, lowered energy intake, and increased behavioral signs of hunger, reflecting their difficulty in switching from a milk diet to solid feed. However, large differences exist between calves in their ability to adapt to solid feed, and automated feeders allow the age of weaning to be adjusted to an individual calf's intake of solid feed. We examined the effects of weaning according to solid feed intake on age at weaning, feed intake, and behavioral signs of hunger. In a 2×2 factorial design, 60 female Holstein calves in groups of 8 and fed milk, grain starter, and hay from automated feeders began to be weaned when their voluntary intake of grain starter was either 400 g/d (high start) or 200 g/d (low start), with weaning completed when their voluntary intakes of starter were either 1,600 g/d (high end) or 800 g/d (low end). Digestible energy intakes were calculated from milk, starter and hay intakes, corrected for body weights, calves were weighed, and the frequency of visits to the milk feeders were measured each day. The main effects and interactions between treatments were tested with ANOVA. Large differences were observed between calves in the age at which weaning was complete, with weaning completed earlier for low-end calves compared with high-end calves. No treatment effects (either of start amount or end amount) on intakes of milk, starter, or hay or on weight gains occurred. However, the calves that began weaning earlier had longer durations of weaning, greater growth rates from d 20 to 87, and were heavier on d 87, and had lower milk intakes, higher starter intakes, higher hay intakes, and a greater digestible energy intake, but showed more unrewarded visits to the milk feeder. Adjusting the age at which individual calves are weaned off milk according to their ability to eat solid feed can reduce the age at which weaning occurs while reducing the

  11. Analyses of thermoregulatory responses of feeder cattle exposed to simulated heat waves

    Science.gov (United States)

    Brown-Brandl, T. M.; Eigenberg, R. A.; Hahn, G. L.; Nienaber, J. A.; Mader, T. L.; Spiers, D. E.; Parkhurst, A. M.

    2005-05-01

    Heat stress in feedlot cattle causes reduced performance, and in the most severe cases, death of the animals, thus causing the loss of millions of dollars in revenue to the cattle industry. A study was designed to evaluate dynamics of thermoregulation and feeding activities when feeder cattle were exposed to simulated heat waves, in comparison with repeated sinusoidal hot and thermoneutral environments. Nine beef steers were randomly assigned to an individual pen in one of three environmental chambers. Each chamber was subjected to each of three temperature regimes (Heatwave simulation from Rockport, Mo., 1995, Heatwave simulation from Columbia, Mo., 1999, and Controlled heat stress treatment of 32±7°C) for a period of 18 days, according to a Latin square treatment design, with a 10-day thermoneutral period (18±7°C) separating treatment periods. Respiration rate, core body temperature, heat production, feed intake, and feeding behavior were measured on each animal for the duration of the experiment. Differences were found in all treatments for all parameters except feeding behavior. It was shown that the two simulated heat waves elicited very different thermoregulatory responses. Based on these results the heat wave centered at Rockport, Mo. in 1995 was devastating because the animals were not acclimated to hot conditions, thus causing an acute response to heat stress. The responses of cattle to conditions at Columbia, Mo. showed some acclimation to heat prior to the peak stress days, and therefore a dampened response was seen. It appears the extreme conditions at Columbia, Mo., 1999 were made severe by environmental conditions not simulated during this study (low wind speed and intensive solar radiation). Overall, it was determined while a cyclic heat stress treatment is a representative model to test heat stress in cattle, further heat stress experiments should be conducted in an actual feedlot.

  12. Uptake, accumulation, and biotransformation of metal oxide nanoparticles by a marine suspension-feeder

    International Nuclear Information System (INIS)

    Montes, Milka O.; Hanna, Shannon K.; Lenihan, Hunter S.; Keller, Arturo A.

    2012-01-01

    Highlights: ► Suspension-feeding by mussels can greatly alter mobility and fate of metal oxide nanoparticles. ► Bioprocessing of metal oxide nanoparticles by mussels removes large fraction from water column. ► Mussels repackage metal oxide nanoparticles in highly concentrated pseudofeces. ► Novel biological pathway between major compartments in marine systems. ► Very different outcome for ZnO and CeO 2 nanoparticles based on their solubility. - Abstract: A growing body of evidence indicates that some engineered nanoparticles (ENPs) are toxic to organisms that perform important ecosystem services in terrestrial and aquatic ecosystems. However, toxicity can be influenced by the biotransformation of contaminants, including ENPs, as it may alter the fate and transport of these substances. In turn, fate and transport can influence their bioavailability. To understand how biotransformation influences the fate and transport of ENPs in marine ecosystems, we exposed suspension-feeding mussels, Mytilus galloprovincialis, to two common nano-metal oxides, CeO 2 and ZnO, over a range of concentrations from 1 mg L −1 to 10 mg L −1 , in a laboratory experiment. Mussels exposed to 10 mg L −1 accumulated 62 μg g −1 of Ce and 880 μg g −1 of Zn on a dry tissue basis but rejected 21,000 μg g −1 for Ce and 63,000 μg g −1 for Zn in pseudofeces. Scanning electron microscope evidence indicates CeO 2 remained as ENPs but ZnO did not after being rejected by the mussels. Mussels filtered most of the CeO 2 from the aqueous media, while a significant fraction of Zn remained in solution. Differences in ENP solubility affect ENP uptake, excretion, and accumulation in mussels. Our study highlights the potential role of marine suspension feeders in biotransformation of ENPs.

  13. A new stalked filter-feeder from the middle Cambrian Burgess Shale, British Columbia, Canada.

    Directory of Open Access Journals (Sweden)

    Lorna J O'Brien

    Full Text Available Burgess Shale-type deposits provide invaluable insights into the early evolution of body plans and the ecological structure of Cambrian communities, but a number of species, continue to defy phylogenetic interpretations. Here we extend this list to include a new soft-bodied animal, Siphusauctum gregarium n. gen. and n. sp., from the Tulip Beds (Campsite Cliff Shale Member, Burgess Shale Formation of Mount Stephen (Yoho National Park, British Columbia. With 1,133 specimens collected, S. gregarium is clearly the most abundant animal from this locality.This stalked animal (reaching at least 20 cm in length, has a large ovoid calyx connected to a narrow bilayered stem and a small flattened or bulb-like holdfast. The calyx is enclosed by a flexible sheath with six small openings at the base, and a central terminal anus near the top encircled by indistinct openings. A prominent organ, represented by six radially symmetrical segments with comb-like elements, surrounds an internal body cavity with a large stomach, conical median gut and straight intestine. Siphusauctum gregarium was probably an active filter-feeder, with water passing through the calyx openings, capturing food particles with its comb-like elements. It often occurs in large assemblages on single bedding planes suggesting a gregarious lifestyle, with the animal living in high tier clusters. These were probably buried en masse more or less in-situ by rapid mud flow events.Siphusauctum gregarium resembles Dinomischus, another Cambrian enigmatic stalked animal. Principal points of comparison include a long stem with a calyx containing a visceral mass and bract-like elements, and a similar lifestyle albeit occupying different tiering levels. The presence in both animals of a digestive tract with a potential stomach and anus suggest a grade of organization within bilaterians, but relationships with extant phyla are not straightforward. Thus, the broader affinities of S. gregarium remain

  14. Glacier Surface Lowering and Stagnation in the Manaslu Region of Nepal

    Science.gov (United States)

    Robson, B. A.; Nuth, C.; Nielsen, P. R.; Hendrickx, M.; Dahl, S. O.

    2015-12-01

    Frequent and up-to-date glacier outlines are needed for many applications of glaciology, not only glacier area change analysis, but also for masks in volume or velocity analysis, for the estimation of water resources and as model input data. Remote sensing offers a good option for creating glacier outlines over large areas, but manual correction is frequently necessary, especially in areas containing supraglacial debris. We show three different workflows for mapping clean ice and debris-covered ice within Object Based Image Analysis (OBIA). By working at the object level as opposed to the pixel level, OBIA facilitates using contextual, spatial and hierarchical information when assigning classes, and additionally permits the handling of multiple data sources. Our first example shows mapping debris-covered ice in the Manaslu Himalaya, Nepal. SAR Coherence data is used in combination with optical and topographic data to classify debris-covered ice, obtaining an accuracy of 91%. Our second example shows using a high-resolution LiDAR derived DEM over the Hohe Tauern National Park in Austria. Breaks in surface morphology are used in creating image objects; debris-covered ice is then classified using a combination of spectral, thermal and topographic properties. Lastly, we show a completely automated workflow for mapping glacier ice in Norway. The NDSI and NIR/SWIR band ratio are used to map clean ice over the entire country but the thresholds are calculated automatically based on a histogram of each image subset. This means that in theory any Landsat scene can be inputted and the clean ice can be automatically extracted. Debris-covered ice can be included semi-automatically using contextual and morphological information.

  15. Stagnation-Point Flow and Heat Transfer over a Nonlinearly Stretching/Shrinking Sheet in a Micropolar Fluid

    Directory of Open Access Journals (Sweden)

    Khairy Zaimi

    2014-01-01

    Full Text Available This paper considers the problem of a steady two-dimensional stagnation-point flow and heat transfer of an incompressible micropolar fluid over a nonlinearly stretching/shrinking sheet. A similarity transformation is employed to convert the partial differential equations into nonlinear ordinary ones which are then solved numerically using a shooting method. Numerical results obtained are presented graphically, showing the effects of the micropolar or material parameter and the stretching/shrinking parameter on the flow field and heat transfer characteristics. The dual solutions are found to exist in a limited range of the stretching/shrinking parameter for the shrinking case, while unique solutions are possible for all positive values of the stretching/shrinking parameter (stretching case. It is also observed that the skin friction coefficient and the magnitude of the local Nusselt number increase as the material parameter increases.

  16. Group method analysis of mixed convection stagnation-point flow of non-Newtonian nanofluid over a vertical stretching surface

    Science.gov (United States)

    Nabwey, Hossam A.; Boumazgour, Mohamed; Rashad, A. M.

    2017-07-01

    The group method analysis is applied to study the steady mixed convection stagnation-point flow of a non-Newtonian nanofluid towards a vertical stretching surface. The model utilized for the nanofluid incorporates the Brownian motion and thermophoresis effects. Applying the one-parameter transformation group which reduces the number of independent variables by one and thus, the system of governing partial differential equations has been converted to a set of nonlinear ordinary differential equations, and these equations are then computed numerically using the implicit finite-difference scheme. Comparison with previously published studies is executed and the results are found to be in excellent agreement. Results for the velocity, temperature, and the nanoparticle volume fraction profiles as well as the local skin-friction coefficient and local Nusselt number are presented in graphical and tabular forms, and discussed for different values of the governing parameters to show interesting features of the solutions.

  17. MHD Stagnation Point Flow of Williamson Fluid over a Stretching Cylinder with Variable Thermal Conductivity and Homogeneous/Heterogeneous Reaction

    Science.gov (United States)

    Bilal, M.; Sagheer, M.; Hussain, S.; Mehmood, Y.

    2017-06-01

    The present study reveals the effect of homogeneous/hetereogeneous reaction on stagnation point flow of Williamson fluid in the presence of magnetohydrodynamics and heat generation/absorption coefficient over a stretching cylinder. Further the effects of variable thermal conductivity and thermal stratification are also considered. The governing partial differential equations are converted to ordinary differential equations with the help of similarity transformation. The system of coupled non-linear ordinary differential equations is then solved by shooting technique. MATLAB shooting code is validated by comparison with the previously published work in limiting case. Results are further strengthened when the present results are compared with MATLAB built-in function bvp4c. Effects of prominent parameters are deliberated graphically for the velocity, temperature and concentration profiles. Skin-friction coefficient and Nusselt number for the different parameters are investigated with the help of tables.

  18. Characteristics of buoyancy force on stagnation point flow with magneto-nanoparticles and zero mass flux condition

    Science.gov (United States)

    Uddin, Iftikhar; Khan, Muhammad Altaf; Ullah, Saif; Islam, Saeed; Israr, Muhammad; Hussain, Fawad

    2018-03-01

    This attempt dedicated to the solution of buoyancy effect over a stretching sheet in existence of MHD stagnation point flow with convective boundary conditions. Thermophoresis and Brownian motion aspects are included. Incompressible fluid is electrically conducted in the presence of varying magnetic field. Boundary layer analysis is used to develop the mathematical formulation. Zero mass flux condition is considered at the boundary. Non-linear ordinary differential system of equations is constructed by means of proper transformations. Interval of convergence via numerical data and plots are developed. Characteristics of involved variables on the velocity, temperature and concentration distributions are sketched and discussed. Features of correlated parameters on Cf and Nu are examined by means of tables. It is found that buoyancy ratio and magnetic parameters increase and reduce the velocity field. Further opposite feature is noticed for higher values of thermophoresis and Brownian motion parameters on concentration distribution.

  19. Stagnation and Storage of Strongly Depleted Melts in Slow-Ultraslow Spreading Oceans: Evidence from the Ligurian Tethys

    Science.gov (United States)

    Piccardo, Giovanni; Guarnieri, Luisa; Padovano, Matteo

    2013-04-01

    Our studies of Alpine-Apennine ophiolite massifs (i.e., Lanzo, Voltri, Ligurides, Corsica) show that the Jurassic Ligurian Tethys oceanic basin was a slow-ultraslow spreading basin, characterized by the exposures on the seafloor of mantle peridotites with extreme compositional variability. The large majority of these peridotites are made of depleted spinel harzburgites and plagioclase peridotites. The former are interpreted as reactive peridotites formed by the reactive percolation of under-saturated, strongly trace element depleted asthenospheric melts migrated by porous flow through the mantle lithosphere. The latter are considered as refertilized peridotites formed by peridotite impregnation by percolated silica-saturated, strongly trace element depleted melts. Strongly depleted melts were produced as low-degrees, single melt increments by near fractional melting of the passively upwelling asthenosphere during the rifting stage of the basin. They escaped single melt increment aggregation, migrated isolated through the mantle lithosphere by reactive porous or channeled flow before oceanic opening, and were transformed into silica-saturated derivative liquids that underwent entrapment and stagnation in the shallow mantle lithosphere forming plagioclase-enriched peridotites. Widespread small bodies of strongly depleted gabbro-norites testify for the local coalescence of these derivative liquids. These melts never reached the surface (i.e., the hidden magmatism), since lavas with their composition have never been found in the basin. Subsequently, aggregated MORB melts upwelled within replacive dunite channels (as evidenced by composition of magmatic clinopyroxenes in dunites), intruded at shallow levels as olivine gabbro bodies and extruded as basaltic lavas, to form the crustal rocks of the oceanic lithosphere (i.e., the oceanic magmatism). Km-scale bodies of MORB olivine gabbros were intruded into the plagioclase-enriched peridotites, which were formed in the

  20. Effects of ohmic heating and viscous dissipation on steady MHD flow near a stagnation point on an isothermal stretching sheet

    Directory of Open Access Journals (Sweden)

    Sharma Pushkar Raj

    2009-01-01

    Full Text Available Aim of the paper is to investigate effects of ohmic heating and viscous dissipation on steady flow of a viscous incompressible electrically conducting fluid in the presence of uniform transverse magnetic field and variable free stream near a stagnation point on a stretching non-conducting isothermal sheet. The governing equations of continuity, momentum, and energy are transformed into ordinary differential equations and solved numerically using Runge-Kutta fourth order with shooting technique. The velocity and temperature distributions are discussed numerically and presented through graphs. Skin-friction coefficient and the Nusselt number at the sheet are derived, discussed numerically, and their numerical values for various values of physical parameters are compared with earlier results and presented through tables.

  1. Lorentz Symmetry Breaking in Quantum Electrodynamics

    OpenAIRE

    Oliveira, D. M.

    2010-01-01

    In this dissertation, we study the implications generated by the Lorentz breaking symmetry in quantum electrodynamics. We analyze fermions interacting with an electromagnetic field in the contexts of quantum mechanics and make radiative corrections. In quantum mechanics, the terms of the Lorentz breaking symmetry were treated as perturbations to the Dirac equation, and their expected values were obtained in a vacuum. In the radiative corrections, the Lorentz breaking symmetry was introduced i...

  2. Rock breaking methods to replace blasting

    Science.gov (United States)

    Zhou, Huisheng; Xie, Xinghua; Feng, Yuqing

    2018-03-01

    The method of breaking rock by blasting has a high efficiency and the cost is relatively low, but the associated vibration, flyrock, production of toxic gases since the 1970’s, the Western developed countries began to study the safety of breaking rock. This paper introduces different methods and their progress to safely break rock. Ideally, safe rock breaking would have little vibration, no fly stone, and no toxic gases, which can be widely used in municipal engineering, road excavation, high-risk mining, quarrying and complex environment.

  3. NPP Krsko small break LOCA analysis

    International Nuclear Information System (INIS)

    Mavko, B.; Petelin, S.; Peterlin, G.

    1987-01-01

    Parametric analysis of small break loss of coolant accident for the Krsko NPP was calculated by using RELAP5/MOD1 computer code. The model that was used in our calculations has been improved over several years and was previously tested in simulation (s) of start-up tests and known NPP Krsko transients. In our calculations we modelled automatic actions initiated by control, safety and protection systems. We also modelled the required operator actions as specified in emergency operating instructions. In small-break LOCA calculations, we varied break sizes in the cold leg. The influence of steam generator tube plugging on small break LOCA accidents was also analysed. (author)

  4. Give me a better break: Choosing workday break activities to maximize resource recovery.

    Science.gov (United States)

    Hunter, Emily M; Wu, Cindy

    2016-02-01

    Surprisingly little research investigates employee breaks at work, and even less research provides prescriptive suggestions for better workday breaks in terms of when, where, and how break activities are most beneficial. Based on the effort-recovery model and using experience sampling methodology, we examined the characteristics of employee workday breaks with 95 employees across 5 workdays. In addition, we examined resources as a mediator between break characteristics and well-being. Multilevel analysis results indicated that activities that were preferred and earlier in the work shift related to more resource recovery following the break. We also found that resources mediated the influence of preferred break activities and time of break on health symptoms and that resource recovery benefited person-level outcomes of emotional exhaustion, job satisfaction, and organizational citizenship behavior. Finally, break length interacted with the number of breaks per day such that longer breaks and frequent short breaks were associated with more resources than infrequent short breaks. (c) 2016 APA, all rights reserved).

  5. Deposition of oral bacteria and polystyrene particles to quartz and dental enamel in a parallel plate and stagnation point flow chamber

    NARCIS (Netherlands)

    Yang, JL; Belder, GF; Busscher, HJ; Bos, R.R.M.

    1999-01-01

    The aim of this paper is to determine to what extent (i) deposition of oral bacteria and polystyrene particles, (ii) onto quartz and dental enamel with and without a salivary conditioning film, (iii) in a parallel plate (PP) and stagnation point (SP) flow chamber and at common Peclet numbers are

  6. Lie-algebra approach to symmetry breaking

    International Nuclear Information System (INIS)

    Anderson, J.T.

    1981-01-01

    A formal Lie-algebra approach to symmetry breaking is studied in an attempt to reduce the arbitrariness of Lagrangian (Hamiltonian) models which include several free parameters and/or ad hoc symmetry groups. From Lie algebra it is shown that the unbroken Lagrangian vacuum symmetry can be identified from a linear function of integers which are Cartan matrix elements. In broken symmetry if the breaking operators form an algebra then the breaking symmetry (or symmetries) can be identified from linear functions of integers characteristic of the breaking symmetries. The results are applied to the Dirac Hamiltonian of a sum of flavored fermions and colored bosons in the absence of dynamical symmetry breaking. In the partially reduced quadratic Hamiltonian the breaking-operator functions are shown to consist of terms of order g 2 , g, and g 0 in the color coupling constants and identified with strong (boson-boson), medium strong (boson-fermion), and fine-structure (fermion-fermion) interactions. The breaking operators include a boson helicity operator in addition to the familiar fermion helicity and ''spin-orbit'' terms. Within the broken vacuum defined by the conventional formalism, the field divergence yields a gauge which is a linear function of Cartan matrix integers and which specifies the vacuum symmetry. We find that the vacuum symmetry is chiral SU(3) x SU(3) and the axial-vector-current divergence gives a PCAC -like function of the Cartan matrix integers which reduces to PCAC for SU(2) x SU(2) breaking. For the mass spectra of the nonets J/sup P/ = 0 - ,1/2 + ,1 - the integer runs through the sequence 3,0,-1,-2, which indicates that the breaking subgroups are the simple Lie groups. Exact axial-vector-current conservation indicates a breaking sum rule which generates octet enhancement. Finally, the second-order breaking terms are obtained from the second-order spin tensor sum of the completely reduced quartic Hamiltonian

  7. Lake Bacterial Assemblage Composition Is Sensitive to Biological Disturbance Caused by an Invasive Filter Feeder.

    Science.gov (United States)

    Denef, Vincent J; Carrick, Hunter J; Cavaletto, Joann; Chiang, Edna; Johengen, Thomas H; Vanderploeg, Henry A

    2017-01-01

    One approach to improve forecasts of how global change will affect ecosystem processes is to better understand how anthropogenic disturbances alter bacterial assemblages that drive biogeochemical cycles. Species invasions are important contributors to global change, but their impacts on bacterial community ecology are rarely investigated. Here, we studied direct impacts of invasive dreissenid mussels (IDMs), one of many invasive filter feeders, on freshwater lake bacterioplankton. We demonstrated that direct effects of IDMs reduced bacterial abundance and altered assemblage composition by preferentially removing larger and particle-associated bacteria. While this increased the relative abundances of many free-living bacterial taxa, some were susceptible to filter feeding, in line with efficient removal of phytoplankton cells of <2 μm. This selective removal of particle-associated and larger bacteria by IDMs altered inferred bacterial functional group representation, defined by carbon and energy source utilization. Specifically, we inferred an increased relative abundance of chemoorganoheterotrophs predicted to be capable of rhodopsin-dependent energy generation. In contrast to the few previous studies that have focused on the longer-term combined direct and indirect effects of IDMs on bacterioplankton, our study showed that IDMs act directly as a biological disturbance to which freshwater bacterial assemblages are sensitive. The negative impacts on particle-associated bacteria, which have been shown to be more active than free-living bacteria, and the inferred shifts in functional group representation raise the possibility that IDMs may directly alter bacterially mediated ecosystem functions. IMPORTANCE Freshwater bacteria play fundamental roles in global elemental cycling and are an intrinsic part of local food webs. Human activities are altering freshwater environments, and much has been learned regarding the sensitivity of bacterial assemblages to a variety of

  8. Uptake, accumulation, and biotransformation of metal oxide nanoparticles by a marine suspension-feeder

    Energy Technology Data Exchange (ETDEWEB)

    Montes, Milka O. [University of California Center for Environmental Implications of Nanotechnology, Bren School of Environmental Science and Management, University of California, Santa Barbara, CA 93106 (United States); University of Texas of the Permian Basin, 4901 E. University, Odessa, TX 79762 (United States); Hanna, Shannon K.; Lenihan, Hunter S. [University of California Center for Environmental Implications of Nanotechnology, Bren School of Environmental Science and Management, University of California, Santa Barbara, CA 93106 (United States); Keller, Arturo A., E-mail: keller@bren.ucsb.edu [University of California Center for Environmental Implications of Nanotechnology, Bren School of Environmental Science and Management, University of California, Santa Barbara, CA 93106 (United States)

    2012-07-30

    Highlights: Black-Right-Pointing-Pointer Suspension-feeding by mussels can greatly alter mobility and fate of metal oxide nanoparticles. Black-Right-Pointing-Pointer Bioprocessing of metal oxide nanoparticles by mussels removes large fraction from water column. Black-Right-Pointing-Pointer Mussels repackage metal oxide nanoparticles in highly concentrated pseudofeces. Black-Right-Pointing-Pointer Novel biological pathway between major compartments in marine systems. Black-Right-Pointing-Pointer Very different outcome for ZnO and CeO{sub 2} nanoparticles based on their solubility. - Abstract: A growing body of evidence indicates that some engineered nanoparticles (ENPs) are toxic to organisms that perform important ecosystem services in terrestrial and aquatic ecosystems. However, toxicity can be influenced by the biotransformation of contaminants, including ENPs, as it may alter the fate and transport of these substances. In turn, fate and transport can influence their bioavailability. To understand how biotransformation influences the fate and transport of ENPs in marine ecosystems, we exposed suspension-feeding mussels, Mytilus galloprovincialis, to two common nano-metal oxides, CeO{sub 2} and ZnO, over a range of concentrations from 1 mg L{sup -1} to 10 mg L{sup -1}, in a laboratory experiment. Mussels exposed to 10 mg L{sup -1} accumulated 62 {mu}g g{sup -1} of Ce and 880 {mu}g g{sup -1} of Zn on a dry tissue basis but rejected 21,000 {mu}g g{sup -1} for Ce and 63,000 {mu}g g{sup -1} for Zn in pseudofeces. Scanning electron microscope evidence indicates CeO{sub 2} remained as ENPs but ZnO did not after being rejected by the mussels. Mussels filtered most of the CeO{sub 2} from the aqueous media, while a significant fraction of Zn remained in solution. Differences in ENP solubility affect ENP uptake, excretion, and accumulation in mussels. Our study highlights the potential role of marine suspension feeders in biotransformation of ENPs.

  9. Effects of meloxicam administration on physiological and performance responses of transported feeder cattle.

    Science.gov (United States)

    Guarnieri Filho, T A; Cooke, R F; Cappellozza, B I; Reis, M M; Marques, R S; Bohnert, D W

    2014-09-01

    This experiment evaluated the effects of meloxicam administration on physiological and performance responses of transported cattle during feedlot receiving. Eighty-four Angus × Hereford steers were ranked by BW on d -10 and assigned to 21 dry lot pens. From d -10 to 0, pens were fed alfalfa-grass hay ad libitum and 2.4 kg/steer daily (DM basis) of a corn-based concentrate. On d 0, pens were randomly assigned to 1) transport for 1,440 km in a livestock trailer and oral administration of meloxicam (1 mg/kg of BW) at loading (d 0), unloading (d 1), and daily from d 2 to 7 of feedlot receiving (MEL; n = 7); 2) the same transportation and treatment schedule of MEL but oral administration of lactose monohydrate (1 mg/kg of BW) instead of meloxicam (TRANS; n = 7); or 3) no transport and oral administration of lactose monohydrate (1 mg/kg of BW) concurrently with treatment administration to MEL and TRANS (CON; n = 7). Upon arrival (d 1), MEL and TRANS steers returned to their pens for a 21-d feedlot receiving with the same diet offered from d -10 to 0. Treatments were administered to steers via oral drench on d 0 and 1 or mixed daily with the concentrate from d 2 to 7. Full BW was recorded before (d -2, -1, and 0) treatment application and at the end of experiment (d 20, 21, and 22) for ADG calculation. Daily DMI was recorded from d 1 to 21. Blood samples were collected on d 0, 1, 3, 5, 7, 10, 14, and 21. During the initial 7 d of feedlot receiving, hay and total DMI were reduced (P ≤ 0.03) in TRANS vs. CON and MEL and similar between CON and MEL (P ≥ 0.26), whereas concentrate DMI did not differ (P = 0.16) among treatments. Mean ADG was reduced (P ≤ 0.03) in TRANS vs. MEL and CON but similar (P = 0.82) between MEL and CON. Moreover, TRANS had reduced G:F vs. CON (P = 0.01) and MEL (P = 0.05), whereas G:F was similar (P = 0.39) between CON and MEL. Serum NEFA concentrations were greater (P meloxicam administration to feeder steers modulated the haptoglobin and

  10. Cell growth and differentiation on feeder layers is predicted to be influenced by bioreactor geometry.

    Science.gov (United States)

    Peng, C A; Palsson, B Ø

    1996-06-05

    Tissue function is comprised of a complex interplay between biological and physicochemical rate processes. The design of bioreactors for tissue engineering must account for these processes simultaneously in order to obtain a bioreactor that provides a uniform environment for tissue growth and development. In the present study we consider the effects of fluid flow and mass transfer on the growth of a tissue in a parallel-plate bioreactor configuration. The parenchymal cells grow on a preformed stromal (feeder) layer that secretes a growth factor that stimulates parenchymal stem cell replication and differentiation. The biological dynamics are described by a unilineage model that describes the replication and differentiation of the tissue stem cell. The physicochemical rates are described by the Navier-Stokes and convective-diffusion equations. The model equations are solved by a finite element method. Two dimensionless groups govern the behavior of the solution. One is the Graetz number (Gz) that describes the relative rates of convection and diffusion, and the other a new dimensionless ratio (designated by P) that describes the interplay of the growth factor production, diffusion, and stimulation. Four geometries (slab, gondola, diamond, and radial shapes) for the parallel-plate bioreactor are analyzed. The uniformity of cell growth is measured by a two-dimensional coefficient of variance. The concentration distribution of the stroma-derived growth factor was computed first based on fluid flow and bioreactor geometry. Then the concomitant cell density distribution was obtained by integrating the calculated growth factor concentration with the parenchymal cell growth and unilineage differentiation process. The spatiotemporal cell growth patterns in four different bioreactor configurations were investigated under a variety of combinations of Gz (10(-1), 10(0), and 10(1)) and P(10(-2), 10(-1), 10(0), 10(1), and 10(2)). The results indicate high cell density and

  11. A new hybrid evolutionary algorithm based on new fuzzy adaptive PSO and NM algorithms for Distribution Feeder Reconfiguration

    International Nuclear Information System (INIS)

    Niknam, Taher; Azadfarsani, Ehsan; Jabbari, Masoud

    2012-01-01

    Highlights: ► Network reconfiguration is a very important way to save the electrical energy. ► This paper proposes a new algorithm to solve the DFR. ► The algorithm combines NFAPSO with NM. ► The proposed algorithm is tested on two distribution test feeders. - Abstract: Network reconfiguration for loss reduction in distribution system is a very important way to save the electrical energy. This paper proposes a new hybrid evolutionary algorithm to solve the Distribution Feeder Reconfiguration problem (DFR). The algorithm is based on combination of a New Fuzzy Adaptive Particle Swarm Optimization (NFAPSO) and Nelder–Mead simplex search method (NM) called NFAPSO–NM. In the proposed algorithm, a new fuzzy adaptive particle swarm optimization includes two parts. The first part is Fuzzy Adaptive Binary Particle Swarm Optimization (FABPSO) that determines the status of tie switches (open or close) and second part is Fuzzy Adaptive Discrete Particle Swarm Optimization (FADPSO) that determines the sectionalizing switch number. In other side, due to the results of binary PSO(BPSO) and discrete PSO(DPSO) algorithms highly depends on the values of their parameters such as the inertia weight and learning factors, a fuzzy system is employed to adaptively adjust the parameters during the search process. Moreover, the Nelder–Mead simplex search method is combined with the NFAPSO algorithm to improve its performance. Finally, the proposed algorithm is tested on two distribution test feeders. The results of simulation show that the proposed method is very powerful and guarantees to obtain the global optimization.

  12. Effects of Rest-Break Intention on Rest-Break Frequency and Work-Related Fatigue.

    Science.gov (United States)

    Blasche, Gerhard; Pasalic, Sanja; Bauböck, Verena-Maria; Haluza, Daniela; Schoberberger, Rudolf

    2017-03-01

    The present paper presents findings from two studies addressing the effects of the employee's intention to have rest breaks on rest-break frequency and the change of well-being during a workday. Rest breaks are effective in avoiding an accumulation of fatigue during work. However, little is known about individual differences in rest-break behavior. In Study 1, the association between rest-break intention and the daily number of rest breaks recorded over 4 consecutive workdays was determined by generalized linear model in a sample of employees ( n = 111, 59% females). In Study 2, professional geriatric nurses ( n = 95 females) who worked over two consecutive 12-hour day shifts recorded well-being (fatigue, distress, effort motivation) at the beginning and the end of their shifts. The effect of rest-break intention on the change of well-being was determined by multilevel modeling. Rest-break intention was positively associated with the frequency of rest breaks (Study 1) and reduced the increase of fatigue and distress over the workday (Study 2). The results indicate that individual differences account for the number of breaks an employee takes and, as a consequence, for variations in the work-related fatigue and distress. Strengthening rest-break intentions may help to increase rest-break behavior to avoid the buildup of fatigue and distress over a workday.

  13. Electric motor efficiency as parameter for sizing a directly connected into transformer feeder cable; Rendimento de motor eletrico como parametro de dimensionamento de bitola de alimentador conectado diretamente ao transformador

    Energy Technology Data Exchange (ETDEWEB)

    Oliveira Filho, Delly; Lacerda Filho, Adilio F.; Martins, Jose H.; Queiroz, Josue M. [Universidade Federal de Vicosa (UFV), MG (Brazil). Dept. de Engenharia Agricola], Emails: delly@ufv.br, alacerda@ufv.br, jhmartins@ufv.br, josue.queiroz@ufv.br; Teixeira, Carlos A. [Universidade Federal Rural de Pernambuco, Serra Talhada, PE (Brazil). Dept. de Agronomia], E-mail: carlos.teixeira@uast.ufrpe.br

    2010-09-15

    The feeder conductors sizing does not take into account criterion for rational use of electricity. This study is about feeder conductors sizing evaluation for motors connected directly to transformers used in rural electrification. In the feeder conductors sizing indicate that besides the attendance of the technical standard (i.e. sizing as a function of the feeder current capacity and the allowable voltage drop) is also to be considered: the number of working hours, the feeder's electrical characteristic and price, the installation characteristics as length and engine's rate. According to the above, in some situations it may be advantageous to increase the gauge of the conductor. It was proven that in some situations it is advantageous to increase the conductor gauge beyond that required by the standards in order to save energy and expenses by the lower feeder losses and by the electric motor higher efficiency. (author)

  14. Implementation of the resonant vibratory feeders control algorithm on Simatic S7-1200 from MATLAB Simulink enviroment

    Directory of Open Access Journals (Sweden)

    Mitrović Radomir B.

    2016-01-01

    Full Text Available Simulink is an important tool for modeling and simulation of process and control algorithms. It's expansion, PLC Coder, enables direct conversion of model subsystem into SCL, structured text code, which is then used by PLC IDE to create function blocks. This shortens developing time of algorithms for PLC controller. Also, this reduces possibility for a coding error. This paper describes Simulink PLC Coder and workflow for developing PID control algorithm for Siemens Simatic S7-1200 PLC. Control object used here is resonant vibratory feeder having electromagnetic drive.

  15. Using Human Gestures and Generic Skills to Instruct a Mobile Robot Arm in a Feeder Filling Scenario

    DEFF Research Database (Denmark)

    Pedersen, Mikkel Rath; Høilund, Carsten; Krüger, Volker

    2012-01-01

    Mobile robots that have the ability to cooperate with humans are able to provide new possibilities to manufac- turing industries. In this paper, we discuss our mobile robot arm that a) can provide assistance at different locations in a factory and b) that can be programmed using complex human...... actions such as pointing in Take this object. In this paper, we discuss the use of the mobile robot for a feeding scenario where a human operator specifies the parts and the feeders through pointing gestures. The system is partially built using generic robotic skills. Through extensive experiments, we...

  16. Human amniotic epithelial cells as feeder layer to derive and maintain human embryonic stem cells from poor-quality embryos

    Directory of Open Access Journals (Sweden)

    Daniela Ávila-González

    2015-09-01

    Full Text Available Data from the literature suggest that human embryonic stem cell (hESC lines used in research do not genetically represent all human populations. The derivation of hESC through conventional methods involve the destruction of viable human embryos, as well the use of mouse embryonic fibroblasts as a feeder layer, which has several drawbacks. We obtained the hESC line (Amicqui-1 from poor-quality (PQ embryos derived and maintained on human amniotic epithelial cells (hAEC. This line displays a battery of markers of pluripotency and we demonstrated the capacity of these cells to produce derivates of the three germ layers.

  17. Index-Based Assessment of Voltage Rise and Reverse Power Flow Phenomena in a Distribution Feeder Under High PV Penetration

    DEFF Research Database (Denmark)

    Hasheminamin, Maryam; Agelidis, Vassilios G.; Salehi, Vahid

    2015-01-01

    -based methodology for assessing the impact of high solar PV generation, considering the reverse power flow and voltage rise phenomena. Indices are defined that link these two phenomena and their impact on the voltage profile across the feeder. This assessment relies on detailed modeling of the network and the solar......The proliferation of photovoltaic (PV) generation in low- and medium-voltage distribution networks is expected to continue. Qualified studies can quantify adverse impacts of high PV penetration on distribution networks and assist utilities in decision making. This paper proposes an index...

  18. Breaking antidunes: Cyclic behavior due to hysteresis

    DEFF Research Database (Denmark)

    Deigaard, Rolf

    2006-01-01

    The cyclic behavior of breaking antidunes (growth, breaking of surface wave, obliteration) is investigated by use of a numerical model. The model includes the transition between supercritical and transcritical flow. As the antidune grows the flow becomes transcritical and a hydraulic jump is form...

  19. Breaking Bad News - Perceptions of Pediatric Residents.

    Science.gov (United States)

    Geeta, M G; Krishnakumar, P

    2017-08-15

    The present study evaluated the perceptions and practice of 92 final year pediatric residents with regard to breaking bad news. Only 16% of residents had received any training in communication skills. Majority (65%) of the residents were not comfortable while breaking bad news.

  20. Symmetry breaking signaling mechanisms during cell polarization

    NARCIS (Netherlands)

    Bruurs, LJM

    2017-01-01

    Breaking of cellular symmetry in order to establish an apico-basal polarity axis initiates de novo formation of cell polarity. However, symmetry breaking provides a formidable challenge from a signaling perspective, because by definition no spatial cues are present to instruct axis establishment.

  1. Structural Break Tests Robust to Regression Misspecification

    NARCIS (Netherlands)

    Abi Morshed, Alaa; Andreou, E.; Boldea, Otilia

    2016-01-01

    Structural break tests developed in the literature for regression models are sensitive to model misspecification. We show - analytically and through simulations - that the sup Wald test for breaks in the conditional mean and variance of a time series process exhibits severe size distortions when the

  2. Strongly coupled semidirect mediation of supersymmetry breaking

    International Nuclear Information System (INIS)

    Ibe, M.; Izawa, K.-I.; Nakai, Y.

    2009-01-01

    Strongly coupled semidirect gauge mediation models of supersymmetry breaking through massive mediators with standard-model charges are investigated by means of composite degrees of freedom. Sizable mediation is realized to generate the standard-model gaugino masses for a small mediator mass without breaking the standard-model symmetries.

  3. On breaks of the Indian monsoon

    Indian Academy of Sciences (India)

    R. Narasimhan (Krishtel eMaging) 1461 1996 Oct 15 13:05:22

    2000) but little overlap with breaks identified by Webster et al (1998). Further, there are three or four active-break cycles in a season according to Webster et al (1998) which implies a time scale of about 40 days for which Goswami and Mohan ...

  4. Dynamical study of symmetries: breaking and restauration

    International Nuclear Information System (INIS)

    Schuck, P.

    1986-09-01

    First symmetry breaking (spontaneous) is explained and the physical implication discussed for infinite systems. The relation with phase transitions is indicated. Then the specific aspects of symmetry breaking in finite systems is treated and illustrated in detail for the case of translational invariance with the help of an oversimplified but exactly solvable model. The method of projection (restauration of symmetry) is explained for the static case and also applied to the model. Symmetry breaking in the dynamical case and for instance the notion of a soft mode responsible for the symmetry breaking is discussed in the case of superfluidity and another exactly solvable model is introduced. The Goldstone mode is treated in detail. Some remarks on analogies with the breaking of chiral symmetry are made. Some recent developments in the theory of symmetry restauration are briefly outlined [fr

  5. Research progress on dam-break floods

    KAUST Repository

    Wu, Jiansong

    2011-08-01

    Because of the catastrophic effects downstream of dam-break failure, more and more researchers around the world have been working on the study of dam-break flows to accurately forecast the downstream inundation mapping. With the rapid development of computer hardware and computing techniques, numerical study on dam-break flows has been a popular research subject. In the paper, the numerical methodologies used to solve the governing partial differential equations of dam-break flows are classified and summarized, and their characteristics and applications are discussed respectively. Furthermore, the fully-developed mathematical models developed in recent decades are reviewed, and also introduced the authors\\' on-going work. Finally, some possible future developments on modeling the dam-break flows and some solutions are presented and discussed. © 2011 IEEE.

  6. Supersymmetry and electroweak breaking in the interval

    International Nuclear Information System (INIS)

    Diego, David; Gersdorff, Gero von; Quiros, Mariano

    2005-01-01

    Hypermultiplets are considered in the five-dimensional interval where all fields are continuous and the boundary conditions are dynamically obtained from the action principle. The orbifold boundary conditions are obtained as particular cases. We can interpret the Scherk-Schwarz supersymmetry breaking as a misalignment of boundary conditions while a new source of supersymmetry breaking corresponding to a mismatch of different boundary parameters is identified. The latter can be viewed as coming from boundary supersymmetry breaking masses for hyperscalars and the nature of the corresponding supersymmetry breaking parameter is analyzed. For some regions of the parameter space where supersymmetry is broken (either by Scherk-Schwarz boundary conditions or by boundary hyperscalar masses) electroweak symmetry breaking can be triggered at the tree level

  7. Chiral symmetry and chiral-symmetry breaking

    International Nuclear Information System (INIS)

    Peskin, M.E.

    1982-12-01

    These lectures concern the dynamics of fermions in strong interaction with gauge fields. Systems of fermions coupled by gauge forces have a very rich structure of global symmetries, which are called chiral symmetries. These lectures will focus on the realization of chiral symmetries and the causes and consequences of thier spontaneous breaking. A brief introduction to the basic formalism and concepts of chiral symmetry breaking is given, then some explicit calculations of chiral symmetry breaking in gauge theories are given, treating first parity-invariant and then chiral models. These calculations are meant to be illustrative rather than accurate; they make use of unjustified mathematical approximations which serve to make the physics more clear. Some formal constraints on chiral symmetry breaking are discussed which illuminate and extend the results of our more explicit analysis. Finally, a brief review of the phenomenological theory of chiral symmetry breaking is presented, and some applications of this theory to problems in weak-interaction physics are discussed

  8. Big break for charge symmetry

    CERN Document Server

    Miller, G A

    2003-01-01

    Two new experiments have detected charge-symmetry breaking, the mechanism responsible for protons and neutrons having different masses. Symmetry is a crucial concept in the theories that describe the subatomic world because it has an intimate connection with the laws of conservation. The theory of the strong interaction between quarks - quantum chromodynamics - is approximately invariant under what is called charge symmetry. In other words, if we swap an up quark for a down quark, then the strong interaction will look almost the same. This symmetry is related to the concept of sup i sospin sup , and is not the same as charge conjugation (in which a particle is replaced by its antiparticle). Charge symmetry is broken by the competition between two different effects. The first is the small difference in mass between up and down quarks, which is about 200 times less than the mass of the proton. The second is their different electric charges. The up quark has a charge of +2/3 in units of the proton charge, while ...

  9. Introducing tool-based feeders to zoo-housed chimpanzees as a cognitive challenge: spontaneous acquisition of new types of tool use and effects on behaviours and use of space.

    OpenAIRE

    Yamanashi, Yumi; Matsunaga, Masayuki; Shimada, Kanae; Kado, Ryuichiro; Tanaka, Masayuki

    2016-01-01

    Cognitively challenging environments are vital to the welfare of captive animals. However, practical enrichment devices that can facilitate animals’ natural behaviours and accommodate individual variation are still limited. We created two types of feeders to facilitate tool-using behaviour in captive chimpanzees: pounding and dipping feeders. The pounding feeder was inspired by pestle-pounding behaviour observed in wild chimpanzees, and we expected that chimpanzees would pound soft foods. The...

  10. Evaluation of the effect of radiation levels and dose rates in irradiation of murine fibroblasts used as a feeder layer in the culture of human keratinocytes

    International Nuclear Information System (INIS)

    Yoshito, Daniele; Almeida, Tiago L.; Santin, Stefany Plumeri; Somessari, Elizabeth S.R.; Silveira, Carlos G. da; Mathor, Monica B.; Altran, Silvana C.; Isaac, Cesar

    2009-01-01

    In 1975, Rheinwald and Green published an effective methodology for obtaining and cultivating human keratinocytes. This methodology consisted of seeding keratinocytes onto a feeder layer composed of lineage 3T3 murine fibroblasts, the proliferation rate of which is then controlled through the action of ionizing radiation. The presence of the feeder layer encourages the development of keratinocyte colonies and their propagation in similar cultures, becoming possible several clinical applications as skin substitutes or wound dressings in situations such as post burn extensive skin loss and other skin disorders. However, good development of these keratinocytes depends on a high quality feeder layer among other factors. In the present work, we evaluated the relationship between radiation levels and dose rates applied to fibroblasts used in construction of feeder layers and the radiation effect on keratinocytes colonies forming efficiency. Results indicate 3T3 lineage murine fibroblasts irradiated with doses varying between 60 and 100 Gy can be used as a feeder layer immediately after irradiation or storage of the irradiated cells in suspension at 4 g C for 24 hours with similar results. The exception is when the irradiation dose rate is 2.75 Gyh -1 ; in this case, results suggested that the fibroblasts should be used immediately after irradiation. (author)

  11. Improving long term driving comfort by taking breaks - How break activity affects effectiveness.

    Science.gov (United States)

    Sammonds, George M; Mansfield, Neil J; Fray, Mike

    2017-11-01

    During long duration journeys, drivers are encouraged to take regular breaks. The benefits of breaks have been documented for safety; breaks may also be beneficial for comfort. The activity undertaken during a break may influence its effectiveness. Volunteers completed 3 journeys on a driving simulator. Each 130 min journey included a 10 min break after the first hour. During the break volunteers either stayed seated, left the simulator and sat in an adjacent room, or took a walk on a treadmill. The results show a reduction in driver discomfort during the break for all 3 conditions, but the effectiveness of the break was dependent on activity undertaken. Remaining seated in the vehicle provided some improvement in comfort, but more was experienced after leaving the simulator and sitting in an adjacent room. The most effective break occurred when the driver walked for 10 min on a treadmill. The benefits from taking a break continued until the end of the study (after a further hour of driving), such that comfort remained the best after taking a walk and worst for those who remained seated. It is concluded that taking a break and taking a walk is an effective method for relieving driving discomfort. Copyright © 2017 Elsevier Ltd. All rights reserved.

  12. A semi-closed recirculating system for the in situ study of feeding and respiration of benthic suspension feeders

    Directory of Open Access Journals (Sweden)

    Marta Ribes

    2000-12-01

    Full Text Available Suspension feeding is one of the most widespread feeding strategies among benthic organisms. However, natural feeding ecology and energetics of benthic suspension feeders are poorly known. The scarcity of field methods, apparatus and protocols that facilitate obtention of reliable in situ data has contributed to this lack of knowledge. A detailed description of an improved semi-closed recirculating system as well as the experimental set up is provided for the study of energetics in benthic suspension feeders. The system, completely submersible and surface-independent, allows us to assess oxygen concentration changes and feeding rates under natural conditions. Methodological examinations are conducted to investigate: a the circulation of the water within the chamber; b the time required for the flushing pump to entirely renew the volume of water of the incubation chambers; c the behavior of the species within the chambers; d the time of acclimation to the chamber conditions for the different species; e the maximum decrease in oxygen concentration without affecting respiration rate; f the time required to detect changes in concentration of the natural food sources. The system and experimental protocol is tested with species from three representative phyla, Porifera, Cnidaria and Tunicata.

  13. Design of a CPW-Fed Band-Notched UWB Antenna Using a Feeder-Embedded Slotline Resonator

    Directory of Open Access Journals (Sweden)

    Amin M. Abbosh

    2008-01-01

    Full Text Available A complete design method for a compact uniplanar ultra-wideband antenna with subband rejection capability is presented. A slotline resonator is incorporated in the coplanar waveguide feeder of the antenna to act as a bandstop filter, hence enabling the rejection of any undesired band within the passband of the antenna. Two samples of the proposed antenna were designed and manufactured. One of the developed antennas does not contain a resonator, whereas the other contains a slotline resonator. The designed antennas feature a compact size of 27 mm × 27 mm. Results of the simulation and measurement show that the designed antennas have a bandwidth from 3 GHz to more than 11 GHz. The results also reveal that the use of the resonator in the feeder of the antenna efficiently rejects any undesired subband, such as the 4.9–5.9 GHz band assigned for IEEE802.11a and HIPERLAN/2. The gain of the antennas with the resonator is about 2.2 dBi at the passband, while it is less than −8 dBi at the rejected subband.

  14. A Review of Power Distribution Test Feeders in the United States and the Need for Synthetic Representative Networks

    Directory of Open Access Journals (Sweden)

    Fernando E. Postigo Marcos

    2017-11-01

    Full Text Available Under the increasing penetration of distributed energy resources and new smart network technologies, distribution utilities face new challenges and opportunities to ensure reliable operations, manage service quality, and reduce operational and investment costs. Simultaneously, the research community is developing algorithms for advanced controls and distribution automation that can help to address some of these challenges. However, there is a shortage of realistic test systems that are publically available for development, testing, and evaluation of such new algorithms. Concerns around revealing critical infrastructure details and customer privacy have severely limited the number of actual networks published and that are available for testing. In recent decades, several distribution test feeders and US-featured representative networks have been published, but the scale, complexity, and control data vary widely. This paper presents a first-of-a-kind structured literature review of published distribution test networks with a special emphasis on classifying their main characteristics and identifying the types of studies for which they have been used. This both aids researchers in choosing suitable test networks for their needs and highlights the opportunities and directions for further test system development. In particular, we highlight the need for building large-scale synthetic networks to overcome the identified drawbacks of current distribution test feeders.

  15. Key Impact Factors on Dam Break Fatalities

    Science.gov (United States)

    Huang, D.; Yu, Z.; Song, Y.; Han, D.; Li, Y.

    2016-12-01

    Dam failures can lead to catastrophes on human society. However, there is a lack of research about dam break fatalities, especially on the key factors that affect fatalities. Based on the analysis of historical dam break cases, most studies have used the regression analysis to explore the correlation between those factors and fatalities, but without implementing optimization to find the dominating factors. In order to understand and reduce the risk of fatalities, this study has proposed a new method to select the impact factors on the fatality. It employs an improved ANN (Artificial Neural Network) combined with LOOCV (Leave-one-out cross-validation) and SFS (Stepwise Forward Selection) approach to explore the nonlinear relationship between impact factors and life losses. It not only considers the factors that have been widely used in the literature but also introduces new factors closely involved with fatalities. Dam break cases occurred in China from 1954 to 2013 are summarized, within which twenty-five cases are selected with a comprehensive coverage of geographic position and temporal variation. Twelve impact factors are taken into account as the inputs, i.e., severity of dam break flood (SF), population at risk (PR), public understanding of dam break (UB), warning time (TW), evacuation condition (EC), weather condition during dam break (WB), dam break mode (MB), water storage (SW), building vulnerability (VB), dam break time (TB), average distance from the affected area to the dam (DD) and preventive measures by government (PG).From those, three key factors of SF, MB and TB are chosen. The proposed method is able to extract the key factors, and the derived fatality model performs well in various types of dam break conditions.

  16. Using 1D theory to understand 3D stagnation of a wire-array Z pinch in the absence of radiation

    Science.gov (United States)

    Yu, Edmund

    2015-11-01

    Many high-energy-density systems implode towards the axis of symmetry, where it collides on itself, forming a hot plasma. However, experiments show these imploding plasmas develop three-dimensional (3D) structures. As a result, the plasma cannot completely dissipate its kinetic energy at stagnation, instead retaining significant 3D flow. A useful tool for understanding the effects of this residual flow is 3D simulation, but the amount and complexity of information can be daunting. To address this problem, we explore the connection between 3D simulation and one-dimensional (1D) theory. Such a connection, if it exists, is mutually beneficial: 1D theory can provide a clear picture of the underlying dynamics of 3D stagnation. On the other hand, deviations between theory and simulation suggest how 1D theory must be modified to account for 3D effects. In this work, we focus on a 3D, magnetohydrodynamic simulation of a compact wire-array Z pinch. To provide a simpler background against which to test our ideas, we artificially turn off radiation during the stagnation phase. Examination of the initial accumulation of mass on axis reveals oblique collision between jets, shock accretion, and vortex formation. Despite evidence for shock-dominated stagnation, a 1D shockless stagnation solution is more appropriate for describing the global dynamics, in that it reproduces the increase of on-axis density with time. However, the 1D solution must be modified to account for 3D effects: the flows suggest enhanced thermal transport as well as centrifugal force. Upon reaching peak compression, the stagnation transitions to a second phase, in which the high-pressure core on axis expands outward into the remaining imploding plasma. During this phase, a 1D shock solution describes the growth of the shock accretion region, as well as the decrease of on-axis density with time. However, the effect of 3D flows is still present: the on-axis temperature does not cool during expansion, which

  17. Particle production from symmetry breaking after inflation

    CERN Document Server

    García-Bellido, J; Garcia-Bellido, Juan; Morales, Ester Ruiz

    2002-01-01

    Recent studies suggest that the process of symmetry breaking after inflation typically occurs very fast, within a single oscillation of the symmetry-breaking field, due to the spinodal growth of its long-wave modes, otherwise known as `tachyonic preheating'. In this letter we show how this sudden transition from the false to the true vacuum can induce a significant production of particles, bosons and fermions, coupled to the symmetry-breaking field. We find that this new mechanism of particle production in the early Universe may have interesting consequences for the origin of dark matter and the generation of the observed baryon asymmetry through leptogenesis.

  18. Critical two-phase flow in pipes for subcooled stagnation states with cavity flooding incipient flashing model

    International Nuclear Information System (INIS)

    Lee, S.Y.; Schrock, V.E.

    1990-01-01

    Analysis of loss of coolant accident (LOCA) scenarios in nuclear reactor safety evaluation depends on knowledge of many complex phenomena. A primary phenomenon controlling the sequence of events, by determining the residual coolant mass inventory within the primary system, is the critical flow process. Critical flow of a flashing liquid is complicated by marked departure from thermal equilbrium. Several complex models have been proposed to represent the non-equilibrium effects, including six-equation two-fluid models. In the present paper a new cavity flooding model is used for the evaluation of pressure undershoot at flashing inception. This model is similar to the one developed by Fabic (1964) for the evaluation of liquid superheat required for boiling on a surface subjected to transient heating. The model contains an experimentally deduced factor, which is correlated against stagnation subcooling using the experimental data of Amos and Schrock (1983, 1984), Jeandey et al. (1981), and the Marviken tests (Anon., 1979). The model was then tested against seven additional data sets and shown to be very accurate in predicted mass flux (standard deviation of 10.9% for all data). The cavity flooding model is thought to represent the true physics more correctly than does the earlier model, which had its origin in molecular fluctuation theory

  19. Surface kinetics for catalytic combustion of hydrogen-air mixtures on platinum at atmospheric pressure in stagnation flows

    Science.gov (United States)

    Ikeda, H.; Sato, J.; Williams, F. A.

    1995-03-01

    Experimental studies of the combustion of premixed hydrogen-air mixtures impinging on the surface of a heated platinum plate at normal atmospheric pressure were performed and employed to draw inferences concerning surface reaction mechanisms and rate parameters applicable under practical conditions of catalytic combustion. Plate and gas temperatures were measured by thermocouples, and concentration profiles of major stable species in the gas were measured by gas-chromatographic analyses of samples withdrawn by quartz probes. In addition, ignition and extinction phenomena were recorded and interpreted with the aid of a heat balance at the surface and a previous flow-field analysis of the stagnation-point boundary layer. From the experimental and theoretical results, conclusions were drawn concerning the surface chemical-kinetic mechanisms and values of the elementary rate parameters that are consistent with the observations. In particular, the activation energy for the surface oxidation step H + OH → H 2O is found to be appreciably less at these high surface coverages than in the low-coverage limit.

  20. Unsteady mixed convection flow of a micro-polar fluid near the stagnation point on a vertical surface

    Energy Technology Data Exchange (ETDEWEB)

    Lok, Y.Y. [Center for Academic Services, Kolej Universiti Teknikal Kebangsaan Malaysia, 75450 Ayer Keroh, Melaka (Malaysia); Amin, N. [Department of Mathematics, Universiti Teknologi Malaysia, 81310 Johor Bahru, Johor (Malaysia); Pop, I. [Faculty of Mathematics, University of Cluj, R-3400 Cluj, CP 253 (Romania)

    2006-12-15

    The unsteady mixed convection boundary-layer flow of a micro-polar fluid near the region of the stagnation point on a double-infinite vertical flat plate is studied. It is assumed that the unsteadiness is caused by the impulsive motion of the free stream velocity and by sudden increase or sudden decrease in the surface temperature from the uniform ambient temperature. The problem is reduced to a system of non-dimensional partial differential equations, which is solved numerically using the Keller-box method. This method may present well-behaved solutions for the transient (small time) solution and those of the steady-state flow (large time) solution. It was found that there is a smooth transition from the small-time solution (initial unsteady-state flow) to the large-time solution (final steady-state flow). Further, it is shown that for both assisting and opposing cases and a fixed value of the Prandtl number, the reduced steady-state skin friction and the steady-state heat transfer from the wall (or Nusselt number) decrease with the increase of the material parameter. On the other hand, it is shown that with the increase of the Prandtl number and a fixed value of the material parameter, the reduced steady-state skin friction decreases when the flow is assisting and it increases when the flow is opposing. (author)

  1. Impedance spectroscopy and structural properties of the perovskite-like Sn(Ba,Sr)O{sub 3} stagnate

    Energy Technology Data Exchange (ETDEWEB)

    Cuervo Farfan, J. [Grupo de Fisica de Nuevos Materiales, Departamento de Fisica, Universidad Nacional de Colombia, AA 5997, Bogota DC (Colombia); Ciencias Basicas, Universidad Manuela Beltran, Bogota DC (Colombia); Olaya, J.J. [Departamento de Ingenieria Mecanica y Mecatronica, Universidad Nacional de Colombia, Bogota DC (Colombia); Vera Lopez, E. [Grupo de Superficies, Electroquimica y Corrosion, Universidad Pedagogica y Tecnologica de Colombia, Tunja (Colombia); Landinez Tellez, D.A. [Grupo de Fisica de Nuevos Materiales, Departamento de Fisica, Universidad Nacional de Colombia, AA 5997, Bogota DC (Colombia); Roa-Rojas, J., E-mail: jroar@unal.edu.co [Grupo de Fisica de Nuevos Materiales, Departamento de Fisica, Universidad Nacional de Colombia, AA 5997, Bogota DC (Colombia)

    2012-08-15

    An exhaustive study of structural, electrical and transport properties on the perovskite stagnate Sn(Ba,Sr)O{sub 3} was performed. Samples of SnBa{sub 1-x}Sr{sub x}O{sub 3} with 0{<=}x{<=}1.00 were prepared by the solid state reaction method. The crystallographic structure was studied by X-ray diffraction experiments and Rietveld refinement using the GSAS code. Results reveal the material synthesized in a cubic structure (space group Pm3-bar m, no. 221) for 0{<=}x{<=}0.50 and in an orthorhombic (space group Pnma, no. 62) for x>0.50. The approximate grain size was found from experiments' Scanning Electron Microscopy. The electric response was studied by the Impedance Spectroscopy technique from 10.0 mHz up to 0,10 MHz. Electric polarization measurements for SnSrO{sub 3} and SnBaO{sub 3} were determined through curves of polarization as a function of applied electric field, which reveal the ferroelectric character of the material. From the saturation polarization the dielectric constants of materials were calculated.

  2. Impedance spectroscopy and structural properties of the perovskite-like Sn(Ba,Sr)O3 stagnate

    International Nuclear Information System (INIS)

    Cuervo Farfán, J.; Olaya, J.J.; Vera López, E.; Landínez Téllez, D.A.; Roa-Rojas, J.

    2012-01-01

    An exhaustive study of structural, electrical and transport properties on the perovskite stagnate Sn(Ba,Sr)O 3 was performed. Samples of SnBa 1-x Sr x O 3 with 0≤x≤1.00 were prepared by the solid state reaction method. The crystallographic structure was studied by X-ray diffraction experiments and Rietveld refinement using the GSAS code. Results reveal the material synthesized in a cubic structure (space group Pm3-bar m, no. 221) for 0≤x≤0.50 and in an orthorhombic (space group Pnma, no. 62) for x>0.50. The approximate grain size was found from experiments' Scanning Electron Microscopy. The electric response was studied by the Impedance Spectroscopy technique from 10.0 mHz up to 0,10 MHz. Electric polarization measurements for SnSrO 3 and SnBaO 3 were determined through curves of polarization as a function of applied electric field, which reveal the ferroelectric character of the material. From the saturation polarization the dielectric constants of materials were calculated.

  3. Unsteady three-dimensional stagnation-point flow and heat transfer of a nanofluid with thermophoresis and Brownian motion effects

    Science.gov (United States)

    Dinarvand, S.; Hosseini, R.; Tamim, H.; Damangir, E.; Pop, I.

    2015-07-01

    An unsteady three-dimensional stagnation-point flow of a nanofluid past a circular cylinder with sinusoidal radius variation is investigated numerically. By introducing new similarity transformations for the velocity, temperature, and nanoparticle volume fraction, the basic equations governing the flow and heat and mass transfer are reduced to highly nonlinear ordinary differential equations. The resulting nonlinear system is solved numerically by the fourth-order Runge-Kutta method with the shooting technique. The thermophoresis and Brownian motion effects occur in the transport equations. The velocity, temperature, and nanoparticle concentration profiles are analyzed with respect to the involved parameters of interest, namely, unsteadiness parameter, Brownian motion parameter, thermophoresis parameter, Prandtl number, and Lewis number. Numerical values of the friction coefficient, diffusion mass flux, and heat flux are computed. It is found that the friction coefficient and heat transfer rate increase with increasing unsteadiness parameter (the highest heat transfer rate at the surface occurs if the thermophoresis and Brownian motion effects are absent) and decrease with increasing both thermophoresis and Brownian motion parameters. The present results are found to be in good agreement with previously published results.

  4. Soret and Dufour effects on convective heat and mass transfer in stagnation-point flow towards a shrinking surface

    International Nuclear Information System (INIS)

    Bhattacharyya, Krishnendu; Layek, G C; Seth, G S

    2014-01-01

    A mathematical model is presented to study the Soret and Dufour effects on the convective heat and mass transfer in stagnation-point flow of viscous incompressible fluid towards a shrinking surface. Suitable similarity transformations are used to convert the governing partial differential equations into self-similarity ordinary differential equations that are then numerically solved by shooting method. Dual solutions for temperature and concentration are obtained in the presence of Soret and Dufour effects. Graphical representations of the heat and mass transfer coefficients, the dimensionless thermal and solute profiles for various values of Prandtl number, Lewis number, Soret number and Dufour number are demonstrated. With Soret number the mass transfer coefficient which is related to mass transfer rate increases for both solutions and the heat transfer coefficient (related to heat transfer rate) for both solutions becomes larger with Dufour number. The Prandtl number causes reduction in heat and the mass transfer coefficients and similarly with the Lewis number mass transfer coefficient decreases. Also, double crossing over is found in dual dimensionless temperature profiles for increasing Soret number and in dual dimensionless concentration profiles for the increase in Dufour number. Due to the larger values of Dufour number the thermal boundary layer increases and for Prandtl number increment it decreases; whereas, the solute boundary layer thickness reduces with increasing values of Prandtl number and Lewis number. (paper)

  5. Dual solutions for MHD stagnation-point flow of a nanofluid over a stretching surface with induced magneticfield

    Directory of Open Access Journals (Sweden)

    Sandeep Naramgari

    2015-11-01

    Full Text Available Present study deals with the buoyancy-driven MHD mixed convection stagnation-point flow, heat and mass transfer of a nanofluid over a non-isothermal stretching sheet in presence of induced magneticfield, radiation, chemical reaction, suction/injection and heat source/sink. The basic governing partial differential equations are reduced to a set of ordinary differential equations by using appropriate similarity transformation. The resulting system is solved numerically by bvp5c Matlab package. Numerical results are validated by comparing with the published results. The influence of non-dimensional governing parameters on velocity, induced magneticfield, temperature and concentration profiles along with coefficient of skin friction, local Nusselt and Sherwood numbers are discussed and presented with the help of graphs and tables. Comparisons are made with the existed studies. Results indicate that dual solutions exists only for certain range of suction/ injection parameter and injection parameter have tendency to enhance the momentum, thermal and concentration boundary layer thickness.

  6. Transport phenomena of carbon nanotubes and bioconvection nanoparticles on stagnation point flow in presence of induced magnetic field

    Science.gov (United States)

    Iqbal, Z.; Azhar, Ehtsham; Maraj, E. N.

    2017-07-01

    This article is a numerical study of stagnation point flow of carbon nanotubes over an elongating sheet in presence of induced magnetic field submerged in bioconvection nanoparticles. Two types of carbon nanotubes are considered i.e. single wall carbon nanotube and multi wall carbon nanotube mixed in based fluid taken to be water as well as kerosene-oil. The emphasis of present study is to examine effect of induced magnetic field on boundary layer flows along with influence of SWCNT and MWCNT. Physical problem is mathematically modeled and simplified by using appropriate similarity transformations. Shooting method with Runge-Kutta of order 5 is employed to compute numerical results for non-dimensional velocity, induced magnetic field and temperature. The effects of pertinent parameters are portrayed through graphs. Numerical values of skinfriction coefficient and Nusselt number are tabulated to study the behaviors at the stretching surface. It is depicted that induced magnetic field is an increasing function of solid nanoparticles volumetric fraction. Moreover, MWCNT contributes in rising induced magnetic field more as compared to SWCNT for both water and kerosene-oil based fluids.

  7. Unconventional supersymmetry and its breaking

    Energy Technology Data Exchange (ETDEWEB)

    Alvarez, Pedro D., E-mail: alvarez@physics.ox.ac.uk [Centro de Estudios Científicos (CECS), Av. Arturo Prat 514, Valdivia (Chile); Universidad Andrés Bello, Av. República 440, Santiago (Chile); Rudolf Peierls Centre for Theoretical Physics, University of Oxford, Oxford (United Kingdom); Pais, Pablo, E-mail: pais@cecs.cl [Centro de Estudios Científicos (CECS), Av. Arturo Prat 514, Valdivia (Chile); Universidad Andrés Bello, Av. República 440, Santiago (Chile); Zanelli, Jorge, E-mail: z@cecs.cl [Centro de Estudios Científicos (CECS), Av. Arturo Prat 514, Valdivia (Chile); Universidad Andrés Bello, Av. República 440, Santiago (Chile)

    2014-07-30

    We present a gauge theory for a superalgebra that includes an internal gauge (G) and local Lorentz (so(1,D−1)) algebras. These two symmetries are connected by fermionic supercharges. The field content of the system includes a (non-)abelian gauge potential A, a spin-1/2 Dirac spinor ψ, the Lorentz connection ω{sup ab}, and the vielbein e{sub μ}{sup a}. The connection one-form A is in the adjoint representation of G, while ψ is in the fundamental. In contrast to standard supersymmetry and supergravity, the metric is not a fundamental field and is in the center of the superalgebra: it is not only invariant under the internal gauge group, G, and under Lorentz transformations, SO(1,D−1), but is also invariant under supersymmetry. The distinctive features of this theory that mark the difference with standard supersymmetries are: i) the number of fermionic and bosonic states is not necessarily the same; ii) there are no superpartners with equal mass; iii) although this supersymmetry originates in a local gauge theory and gravity is included, there is no gravitino; iv) fermions acquire mass from their coupling to the background or from higher order self-couplings, while bosons remain massless. In odd dimensions, the Chern–Simons (CS) form provides an action that is (quasi-)invariant under the entire superalgebra. In even dimensions, the Yang–Mills (YM) form is the only natural option and the symmetry breaks down to G⊗SO(1,D−1). In four dimensions, the construction follows the Townsend–Mac Dowell–Mansouri approach, starting with an osp(4|2)∼usp(2,2|1) connection. Due to the absence of osp(4|2)-invariant traces in four dimensions, the resulting Lagrangian is only invariant under u(1)⊕so(3,1), which includes a Nambu–Jona-Lasinio (NJL) term. In this case, the Lagrangian depends on a single dimensionful parameter that fixes Newton's constant, the cosmological constant and the NJL coupling.

  8. Bacterial Feeders, the Nematode Caenorhabditis elegans and the Flagellate Cercomonas longicauda, have different Effects on Outcome of Competition among the Pseudomonas Biocontrol Strains CHA0 and DSS73

    DEFF Research Database (Denmark)

    Pedersen, Annette; Nybroe, Ole; Winding, Anne

    2009-01-01

    50090 or one of two biocontrol strains P. fluorescens CHA0 or Pseudomonas sp. DSS73) or combinations of two bacterial strains. DSM50090 is a suitable food bacterium, DSS73 is of intermediate food quality, and CHA0 is inedible to the bacterial feeders. Bacterial and protozoan cell numbers were measured......How bacterial feeding fauna affects colonization and survival of bacteria in soil is not well understood, which constrains the applicability of bacterial inoculants in agriculture. This study aimed to unravel how food quality of bacteria and bacterial feeders with different feeding habits (the...

  9. Tidal Mixing at the Shelf Break

    National Research Council Canada - National Science Library

    Hogg, Nelson; Legg, Sonya

    2005-01-01

    The aim of this project was to study mixing forced by tidal flow over sudden changes in topographic slope such as near the shelf-break, using high-resolution nonhydrostatic numerical simulations employing the MIT gem...

  10. Water Breaking: Understand This Sign of Labor

    Science.gov (United States)

    Healthy Lifestyle Labor and delivery, postpartum care Water breaking worries? Prepare yourself for childbirth by getting the facts about this important sign of labor. By Mayo Clinic Staff If you're ...

  11. Higgsless grand unified theory breaking and trinification

    International Nuclear Information System (INIS)

    Carone, Christopher D.; Conroy, Justin M.

    2004-01-01

    Boundary conditions on an extra dimensional interval can be chosen to break bulk gauge symmetries and to reduce the rank of the gauge group. We consider this mechanism in models with gauge trinification. We determine the boundary conditions necessary to break the trinified gauge group directly down to that of the standard model. Working in an effective theory for the gauge-symmetry-breaking parameters on a boundary, we examine the limit in which the grand-unified theory-breaking-sector is Higgsless and show how one may obtain the low-energy particle content of the minimal supersymmetric standard model. We find that gauge unification is preserved in this scenario, and that the differential gauge coupling running is logarithmic above the scale of compactification. We compare the phenomenology of our model to that of four dimensional 'trinified' theories

  12. Proposed changes in intermediate pipe break criteria

    International Nuclear Information System (INIS)

    Schmitz, R.P.

    1984-01-01

    Bechtel Power Corporation proposed to the US NRC in 1983 that the NRC eliminate from their criteria all intermediate breaks. Bechtel's rationale for the proposal and support for their position are presented

  13. The problem of symmetry breaking hierarchy

    International Nuclear Information System (INIS)

    Natale, A.A.

    1983-01-01

    The problem of symmetry breaking hierarchy in grand unified theories is discussed, proving the impossibility to get a big hierarchy of interactions, in a natural way within the framework of perturbation theory. (L.C.) [pt

  14. Phil Anderson and Gauge Symmetry Breaking

    Science.gov (United States)

    Witten, Edward

    In this article, I describe the celebrated paper that Phil Anderson wrote in 1962 with early contributions to the idea of gauge symmetry breaking in particle physics. To set the stage, I describe the work of Julian Schwinger to which Anderson was responding, and also some of Anderson's own work on superconductivity that provided part of the context. After describing Anderson's work I describe the later work of others, leading to the modern understanding of gauge symmetry breaking in weak interactions...

  15. An experimental study on the influence of water stagnation and temperature change on water quality in a full-scale domestic drinking water system

    OpenAIRE

    Zlatanović, L.; van der Hoek, J.P.; Vreeburg, J.H.G.

    2017-01-01

    The drinking water quality changes during the transport through distribution systems. Domestic drinking water systems (DDWSs), which include the plumbing between the water meter and consumer's taps, are the most critical points in which water quality may be affected. In distribution networks, the drinking water temperature and water residence time are regarded as indicators of the drinking water quality. This paper describes an experimental research on the influence of stagnation time and tem...

  16. Bubble Rise and Break-Up in Volcanic Conduits

    Science.gov (United States)

    Soldati, A.; Cashman, K. V.; Rust, A.; Rosi, M.

    2013-12-01

    The continual passive degassing occurring at open-vent mafic volcanoes is often punctuated by bursts of active degassing. The latter are generally thought to be the result of slug flow: large, conduit-filling bubbles periodically rising up the feeder conduit and bursting at the magma-air interface. Existing models of volcanic degassing systems make the simplifying assumption that the conduit is cylindrical; however, while this may be true at shallow levels, a flaring probably connects it to a dyke-like geometry at depth. The overall goal of this research is to assess the influence of conduit geometry on the speed and stability of bubbles rising in open-vent systems, and ultimately to devise a model to infer conduit shape from emerging bubbles size. In order to do that an analogue experimental approach was used. All of the experiments were two-phase (melt+volatiles); the analogue materials of choice were golden syrup-water mixtures ranging in viscosity from 10-1 to 104 Pa*s and air. Two experimental apparatuses were used: a bi-dimensional and a tri-dimensional one. The bi-dimensional set-up is a cell made of two flat transparent PVC plates (44x23cm) 10mm or 5mm apart (the front one having a hole at the bottom permitting bubble injection) containing a variety of parallelepipeds apt to outline different plumbing system geometries. The tri-dimensional one consists of a cylindrical tube (r=1,5cm; l=7cm) allowing bubble injection through the bottom rubber tap and terminating into a square tank (l=22cm). Results indicate that conduit geometry directly controls the slug rise velocity and the surrounding liquid descending speed, which in turn control the slug stability. Small enough bubbles simply deform as they go through the flaring, while bigger ones split into two daughter bubbles. A regime diagram has been constructed, illustrating the bubble break-up threshold dependence on the flare geometry and initial slug size, the two main controlling factors. The phenomenon of

  17. Stagnations of increasing trends in negative pressure with repeated cavitation in water/metal Berthelot tubes as a result of mechanical sealing

    International Nuclear Information System (INIS)

    Hiro, Kazuki; Ohde, Yoshihito; Tanzawa, Yasutoshi

    2003-01-01

    To investigate effects of mechanical sealing on negative pressures in water/metal tube Berthelot systems, trends in negative pressure are observed through runs of temperature cycles below 90 deg. C in two systems made of metals having small amounts of gas inclusions. The first system is a pre-degassed all-stainless-steel tube/plug system. The steel is a special product for vacuum engineering. The second is the same tube sealed with plugs made of silver solidified one-dimensionally in a vacuum furnace. A new type of trend, stagnation for intermediate cycles is found in both systems so long as sealing distortion of each plug is small in amount. The stagnation period for the first system is longer than that for the second one. A metallurgical mechanism of a gas-being-replenished crevice model is proposed: distorted parts of metals undergo heat-treatment during runs of temperature cycles, and the heat-treatment enhances the rates of impurity gas transports to crevices on the metal surface where cavitation occurs, and the transport causes the stagnation for cycles during which the rates are still high

  18. Hydraulic Response of Caisson Breakwaters in Multidirectional Breaking and Non-Breaking Waves

    DEFF Research Database (Denmark)

    Grønbech, J.; Kofoed, Jens Peter; Hald, Tue

    1998-01-01

    The present paper concerns the results and findings of a physical study on wave impacts on vertical caisson breakwaters situated in irregular, multidirectional breaking seas. The study has taken place as part of the framework programme "Dynamic of Structures" financially supported by the Danish...... induced loading and overtopping on caisson breakwaters situated in breaking seas. Regarding the wave forces only minor differences between breaking and non breaking waves in deep water were observed, and it was found that the prediction formula of Goda also seems to apply well for multidirectionally...

  19. Influence of copper oxide nanoparticle form and shape on toxicity and bioaccumulation in the deposit feeder, Capitella teleta

    DEFF Research Database (Denmark)

    Dai, Lina; Banta, Gary Thomas; Selck, Henriette

    2015-01-01

    Few in vivo studies have been conducted to assess how nanoparticle (NP) characteristics such as particle form and shape affect their toxicity and bioaccumulation. In the present study, the deposit feeder, Capitella teleta, was used to investigate the influence of copper form (CuO NPs, micron......-sized CuO particles, and aqueous Cu) and CuO NP shape (spheres, rods and platelets) on toxicity and bioaccumulation through sediment exposures of approximately 250 μg Cu/g dw sed. There were no effects of nanoparticle form or shape on mortality or growth rate during the exposure period. However, mortality...... increased to approximately 26.3% on average in all Cu treatments after the depuration period indicating a delayed effect of Cu exposure, despite more than 90% depuration of Cu during this period. A significant effect of nanoparticle shape was detected on body burden, the gross uptake rate constant...

  20. Development of an extruder-feeder biomass direct liquefaction process. Volume 2, Parts 4--8: Final report

    Energy Technology Data Exchange (ETDEWEB)

    White, D.H.; Wolf, D. [Arizona Univ., Tucson, AZ (United States). Dept. of Chemical Engineering

    1991-10-01

    As an abundant, renewable, domestic energy resource, biomass could help the United States reduce its dependence on imported oil. Biomass is the only renewable energy technology capable of addressing the national need for liquid transportation fuels. Thus, there is an incentive to develop economic conversion processes for converting biomass, including wood, into liquid fuels. Through research sponsored by the US DOE`s Biomass Thermochemical Conversion Program, the University of Arizona has developed a unique biomass direct liquefaction system. The system features a modified single-screw extruder capable of pumping solid slurries containing as high as 60 wt% wood flour in wood oil derived vacuum bottoms at pressures up to 3000 psi. The extruder-feeder has been integrated with a unique reactor by the University to form a system which offers potential for improving high pressure biomass direct liquefaction technology. The extruder-feeder acts simultaneously as both a feed preheater and a pumping device for injecting wood slurries into a high pressure reactor in the biomass liquefaction process. An experimental facility was constructed and following shakedown operations, wood crude oil was produced by mid-1985. By July 1988, a total of 57 experimental continuous biomass liquefaction runs were made using White Birch wood feedstock. Good operability was achieved at slurry feed rates up to 30 lb/hr, reactor pressures from 800 to 3000 psi and temperatures from 350{degree}C to 430{degree}C under conditions covering a range of carbon monoxide feed rates and sodium carbonate catalyst addition. Crude wood oils containing as little as 6--10 wt% residual oxygen were produced. 38 refs., 82 figs., 26 tabs.

  1. Nonlinear radiative heat transfer in magnetohydrodynamic (MHD stagnation point flow of nanofluid past a stretching sheet with convective boundary condition

    Directory of Open Access Journals (Sweden)

    Wubshet Ibrahim

    2015-12-01

    Full Text Available Two-dimensional boundary layer flow of nanofluid fluid past a stretching sheet is examined. The paper reveals the effect of non-linear radiative heat transfer on magnetohydrodynamic (MHD stagnation point flow past a stretching sheet with convective heating. Condition of zero normal flux of nanoparticles at the wall for the stretched flow is considered. The nanoparticle fractions on the boundary are considered to be passively controlled. The solution for the velocity, temperature and nanoparticle concentration depends on parameters viz. Prandtl number Pr, velocity ratio parameter A, magnetic parameter M, Lewis number Le, Brownian motion Nb, and the thermophoresis parameter Nt. Moreover, the problem is governed by temperature ratio parameter (Nr=TfT∞ and radiation parameter Rd. Similarity transformation is used to reduce the governing non-linear boundary-value problems into coupled higher order non-linear ordinary differential equation. These equations were numerically solved using the function bvp4c from the matlab software for different values of governing parameters. Numerical results are obtained for velocity, temperature and concentration, as well as the skin friction coefficient and local Nusselt number. The results indicate that the skin friction coefficient Cf increases as the values of magnetic parameter M increase and decreases as the values of velocity ratio parameter A increase. The local Nusselt number −θ′(0 decreases as the values of thermophoresis parameter Nt and radiation parameter Nr increase and it increases as the values of both Biot number Bi and Prandtl number Pr increase. Furthermore, radiation has a positive effect on temperature and concentration profiles.

  2. Effects of plasma jet parameters, ionization, thermal conduction, and radiation on stagnation conditions of an imploding plasma liner

    Science.gov (United States)

    Stanic, Milos

    The disciplines of High Energy Density Physics (HEDP) and Inertial Confinement Fusion (ICF) are characterized by hypervelocity implosions and strong shocks. The Plasma Liner Experiment (PLX) is focused on reaching HEDP and/or ICF relevant regimes in excess of 1 Mbar peak pressure by the merging and implosion of discrete plasma jets, as a potentially efficient path towards these extreme conditions in a laboratory. In this work we have presented the first 3D simulations of plasma liner, formation, and implosion by the merging of discrete plasma jets in which ionization, thermal conduction, and radiation are all included in the physics model. The study was conducted by utilizing a smoothed particle hydrodynamics code (SPHC) and was a part of the plasma liner experiment (PLX). The salient physics processes of liner formation and implosion are studied, namely vacuum propagation of plasma jets, merging of the jets (liner forming), implosion (liner collapsing), stagnation (peak pressure), and expansion (rarefaction wave disassembling the target). Radiative transport was found to significantly reduce the temperature of the liner during implosion, thus reducing the thermal expansion rates and leaving more pronounced gradients in the plasma liner during the implosion compared with ideal hydrodynamic simulations. These pronounced gradients lead to a greater sensitivity of initial jet geometry and symmetry on peak pressures obtained. Accounting for ionization and transport, many cases gave higher peak pressures than the ideal hydrodynamic simulations. Scaling laws were developed accordingly, creating a non-dimensional parameter space in which performance of an imploding plasma jet liner can be estimated. It is shown that HEDP regimes could be reached with ≈ 5 MJ of liner energy, which would translate to roughly 10 to 20 MJ of stored (capacitor) energy. This is a potentially significant improvement over the currently available means via ICF of achieving HEDP and nuclear

  3. Cultivation and irradiation of human fibroblasts in a medium enriched with platelet lysate for obtaining feeder layer in epidermal cell culture

    International Nuclear Information System (INIS)

    Yoshito, Daniele

    2011-01-01

    For over 30 years, the use of culture medium, enriched with bovine serum, and murines fibroblasts, with the rate of proliferation controlled by irradiation or by share anticarcinogenic drugs, has been playing successfully its role in assisting in the development of keratinocytes in culture, for clinical purposes. However, currently there is a growing concern about the possibility of transmitting prions and animals viruses to transplanted patients. Taking into account this concern, the present work aims to cultivate human fibroblasts in a medium enriched with human platelets lysate and determine the irradiation dose of these cells, for obtaining feeder layer in epidermal cell culture. For carrying out the proposed objective, platelets lysis has standardized, this lysate was used for human fibroblasts cultivation and the irradiation dose enough to inhibit its duplication was evaluated. Human keratinocytes were cultivated in these feeder layers, in culture medium enriched with the lysate. With these results we conclude that the 10% platelets lysate promoted a better adhesion and proliferation of human fibroblasts and in all dose levels tested (60 to 300 Gy), these had their mitotic activity inactivated by ionizing irradiation, being that the feeder layers obtained with doses from 70 to 150 Gy were those that provided the best development of keratinocytes in medium containing 2.5% of human platelet lysate. Therefore, it was possible to standardize both the cultivation of human fibroblasts as its inactivation for use as feeder layer in culture of keratinocytes, so as to eliminate xenobiotics components. (author)

  4. A feeder-cell independent subpopulation of the PICM-19 pig liver stem cell line capable of long-term growth and extensive expansion

    Science.gov (United States)

    A method for the feeder-independent culture of PICM-19 pig liver stem cell line was recently devised, but the cell line’s growth was finite and the cells essentially ceased dividing after approximately 20 passages over a one year culture period. Here we report the isolation, continuous culture, and...

  5. Network integration modelling of feeder and BRT(bus rapid transit) to reduce the usage of private vehicles in Palembang’s suburban area

    Science.gov (United States)

    Nur'afalia, D.; Afifa, F.; Rubianto, L.; Handayeni, K. D. M. E.

    2018-01-01

    The aim of this research is to determine the optimal feeder network route that integrates with BRT (Bus Rapid Transit). Palembang, a high growing population city with unresolved transportation demand sector. BRT as main public transportation could not fulfill people’s demand in transportation, especially in Alang-Alang Lebar sub-district. As an impact, the usage of private vehicles increases along the movement toward the city center. The concept of Network Integration that integrates feeder network with BRT is expected to be a solution to suppress the rate of private vehicles’ usage and to improve public transportation service, so that the use of BRT will be increased in the suburban area of Palembang. The method used to identifying the optimal route using Route Analysis method is route analysis using Tranetsim 0.4. The best route is obtained based on 156 movement samples. The result is 58,7% from 199 mobility’s potency of private vehicle usage’s can be reduced if there is a feeder network’s route in Alang-Alang Lebar’s sub-district. From the result, the existance of integration between feeder network and BRT is potential enough to reduce the usage of private vehicles and supports the sustainability of transportation mobility in Palembang City.

  6. Effect of stall design on dairy calf transition to voluntary feeding on an automatic milk feeder after introduction to group housing.

    Science.gov (United States)

    Wilson, Tanya R; LeBlanc, Stephen J; DeVries, Trevor J; Haley, Derek B

    2018-03-14

    Automatic milk feeders (AMF) for young dairy calves are widely used in the dairy industry. These feeders are thought to have benefits for calf health and welfare and may reduce labor required for feeding; however, little is known about how calves adapt to feeding with AMF. The objective of this study was to observe the effects of feeding stall design on calves learning to use the AMF. The hypothesis was that solid side stalls, compared with steel bar stalls, would result in a longer latency to approach and feed from the AMF without assistance. A total of 147 Holstein calves (80 male and 67 female) were enrolled at 4 d of age, introduced to a group pen, and, at the same time, trained on an AMF. For training, calves were allowed to suck on the trainer's fingers and guided to the teat. Calves were allocated to 1 of 2 stall designs at the pen level, depending on which treatment cohort they were born into, either with steel bar stall walls (n = 46 male, 34 female calves) or with solid side stall walls (n = 34 male, 33 female calves). For 72 h after introductory training on the AMF, data from the feeders were collected and calf behavior was monitored by video. Outcomes measured included latency to first voluntary visit to the feeder and to first feeding, time spent in the feeder, amount of milk consumed over 72 h, number of retraining sessions required (retrained if linear regression models or a Poisson model for the outcome of retraining. For certain outcomes the effects of stall design interacted with difficulty of training (willingness to enter feeder and drink); for the 38% of calves that were scored as moderately difficult to train on a scale of easy, moderate, or difficult, treatment (stall design) differences were detected. These calves took 2× longer to lick or bite toward the nipple, 2× longer to first voluntarily feeding, and consumed less milk over 72 h following training when trained on the steel bar stall design. These results suggest simple features of a

  7. Chiral symmetry and chiral-symmetry breaking

    Energy Technology Data Exchange (ETDEWEB)

    Peskin, M.E.

    1982-12-01

    These lectures concern the dynamics of fermions in strong interaction with gauge fields. Systems of fermions coupled by gauge forces have a very rich structure of global symmetries, which are called chiral symmetries. These lectures will focus on the realization of chiral symmetries and the causes and consequences of thier spontaneous breaking. A brief introduction to the basic formalism and concepts of chiral symmetry breaking is given, then some explicit calculations of chiral symmetry breaking in gauge theories are given, treating first parity-invariant and then chiral models. These calculations are meant to be illustrative rather than accurate; they make use of unjustified mathematical approximations which serve to make the physics more clear. Some formal constraints on chiral symmetry breaking are discussed which illuminate and extend the results of our more explicit analysis. Finally, a brief review of the phenomenological theory of chiral symmetry breaking is presented, and some applications of this theory to problems in weak-interaction physics are discussed. (WHK)

  8. Modelling oil price volatility with structural breaks

    International Nuclear Information System (INIS)

    Salisu, Afees A.; Fasanya, Ismail O.

    2013-01-01

    In this paper, we provide two main innovations: (i) we analyze oil prices of two prominent markets namely West Texas Intermediate (WTI) and Brent using the two recently developed tests by Narayan and Popp (2010) and Liu and Narayan, 2010 both of which allow for two structural breaks in the data series; and (ii) the latter method is modified to include both symmetric and asymmetric volatility models. We identify two structural breaks that occur in 1990 and 2008 which coincidentally correspond to the Iraqi/Kuwait conflict and the global financial crisis, respectively. We find evidence of persistence and leverage effects in the oil price volatility. While further extensions can be pursued, the consideration of asymmetric effects as well as structural breaks should not be jettisoned when modelling oil price volatility. - Highlights: ► We analyze oil price volatility using NP (2010) and LN (2010) tests. ► We modify the LN (2010) to account for leverage effects in oil price. ► We find two structural breaks that reflect major global crisis in the oil market. ► We find evidence of persistence and leverage effects in oil price volatility. ► Leverage effects and structural breaks are fundamental in oil price modelling.

  9. Jet simulations and gamma-ray burst afterglow jet breaks

    NARCIS (Netherlands)

    van Eerten, H.J.; Meliani, Z.; Wijers, R.A.M.J.; Keppens, R.

    2011-01-01

    The conventional derivation of the gamma-ray burst afterglow jet break time uses only the blast wave fluid Lorentz factor and therefore leads to an achromatic break. We show that in general gamma-ray burst afterglow jet breaks are chromatic across the self-absorption break. Depending on

  10. 19 CFR 149.4 - Bulk and break bulk cargo.

    Science.gov (United States)

    2010-04-01

    ... 19 Customs Duties 2 2010-04-01 2010-04-01 false Bulk and break bulk cargo. 149.4 Section 149.4... TREASURY (CONTINUED) IMPORTER SECURITY FILING § 149.4 Bulk and break bulk cargo. (a) Bulk cargo exempted.... (b) Break bulk cargo exempted from time requirement. For break bulk cargo that is exempt from the...

  11. Calculation of the limiting CESSAR Feedwater Line-Break and Steam Line-Break transients

    International Nuclear Information System (INIS)

    Peeler, G.B.; Kennedy, M.F.; Caraher, D.L.; Guttmann, J.; Chung, K.S.

    1983-01-01

    Argonne National Laboratory (ANL), under contract to the Nuclear Regulatory Commission, performed audit calculations of the limiting Feedwater Line Break (FLB) and Steam Line Break (SLB) transients presented in the CESSAR FSAR. The results of the FLB and SLB calculations are discussed

  12. Rule-making, rule breaking? Law breaking by government in the Netherlands and the United Kingdom

    NARCIS (Netherlands)

    Huberts, L.W.J.C.; van Montfort, A.J.G.M.; Doig, A.; Clark, D.

    2006-01-01

    This article concerns a relatively novel issue: rule breaking and unlawful conduct by government bodies; to which degree does it occur, what is the nature of this misconduct, what are the underlying motives, and what are the consequences and possible solutions? Rule and law breaking is harmful for

  13. The effect of a hay grid feeder on feed consumption and measurement of the gastric pH using an intragastric electrode device in horses: a preliminary report.

    Science.gov (United States)

    Aristizabal, F; Nieto, J; Yamout, S; Snyder, J

    2014-07-01

    Obesity and gastric ulceration are highly prevalent in horses. Management modifications for preventing squamous gastric ulceration include frequent feeding and free access to pasture; however, these practices may predispose horses to obesity. To compare the percentage of hay consumed, intragastric pH and horse activity between feeding from the ground and a hay grid feeder. Crossover experimental study. A pH electrode was inserted into the stomach to record the intragastric pH for 48 h. Horses received 1% of their body weight in grass hay twice a day. Horses were assigned to be fed from the ground or a commercial hay grid feeder for 24 h and then switched to the opposite protocol for an additional 24 h. Horses were continuously video-recorded and the percentage of time spent eating or drinking, walking or standing, and lying down were calculated. Two point data were compared by paired t test and pH over time was compared by repeated measures ANOVA. Horses consumed significantly greater amounts of grass hay when fed on the ground compared with a hay grid feeder (n = 9; PpH values (n = 6; P = 0.97), mean intragastric pH over time (n = 6; P = 0.45) the length of time the pH was below 4.0 (n = 6; P = 0.54), and the percentage of time horses spent eating or drinking (n = 9; P = 0.52), walking or standing (n = 9; P = 0.3), or lying down (n = 9; P = 0.4). Within each group horses spent more time eating during the day compared with the night (n = 9; hay grid feeder P = 0.003; ground feeding P = 0.007). The hay grid feeder studied may be used to reduce the amount of hay ingested by horses without reducing the time horses spend eating. © 2013 EVJ Ltd.

  14. Break-glass handling exceptional situations in access control

    CERN Document Server

    Petritsch, Helmut

    2014-01-01

    Helmut Petritsch describes the first holistic approach to Break-Glass which covers the whole life-cycle: from access control modeling (pre-access), to logging the security-relevant system state during Break-Glass accesses (at-access), and the automated analysis of Break-Glass accesses (post-access). Break-Glass allows users to override security restrictions in exceptional situations. While several Break-Glass models specific to given access control models have already been discussed in research (e.g., extending RBAC with Break-Glass), the author introduces a generic Break-Glass model. The pres

  15. DIDACTICS: DEVELOPMENT OR STAGNATION?

    Directory of Open Access Journals (Sweden)

    I. P. Smirnov

    2016-01-01

    Full Text Available ARTICLE RETRACTEDThe aim of the paper – the detailed analysis of the monograph «Contents and Structure of Regularities of Process of Training (Theory and Experiment» which is written by the corresponding member of the Russian Academy of Education (RAE, Doctor of pedagogical sciences, Professor I. I. Logvinov. The book was included into a series «Basic researches of institute of the theory and history of pedagogics of the Russian Academy of Education. Proceedings 2008–2012».The review of the monograph of I. I. Logvinov has become a reason for reflections of the author of the present publication about actual, most burning issues of a modern Russian educational system: on the status of pedagogics in modern domestic science; evolutions of didactic knowledge and its typology; quality of dissertation researches and emasculation in scientific pedagogical concepts of the fundamental bases; ideologization of didactics and a role of the state in this process.Sorting basic thesis of I. I. Logvinov’s work, in something agreeing, and in something arguing with the scientist, the author of article claims that it is a serious and necessary work where the extremely important questions concerning the most painful points of the Russian pedagogical science and a condition of our education in general are brought up.

  16. Breathtaking or stagnation?

    DEFF Research Database (Denmark)

    Sauer, Johannes; Graversen, Jesper Tranbjerg; Park, Tim

    2006-01-01

    techniques. Finally we try to conclude on the significance of subsidies for promoting long term growth in organic production by estimating a bootstrapped bivariate probit model with respect to factors influencing the probability of organic market exit. The results revealed significant difference...... in the organic farms' technical efficiency, no significant total factor productivity growth and even a slightly negative rate of technical change in the period investigated. We found evidence for a positive relationship between subsidy payments and an increase in farm efficiency, technology improvements...... and a decreasing probability of organic market exit which was also confirmed for off farm income. Finally the general index mode specification was found to deliver a more accurate mapping of total factor productivity growth....

  17. Heating plant privatization stagnates

    International Nuclear Information System (INIS)

    Janoska, J.; Benka, M.; Sobinkovic, B.; Haluza, I.

    2005-01-01

    The state has been talking about privatization of 6 municipal heating plants since 2001. The tenders were to start last year. But nothing has happened and the future is uncertain. The city councils would prefer to receive, if not 100%, then at least a majority stake in the heating plants free of charge. But the Cabinet has decided to sell 51% to investors. The privatization agency - the National Property Fund (FNM) is preparing a proposal to increase the stake offered for sale to 67%. According to information provided by the FNM the sale will begin after Cabinet approval. The Fund intends to apply the same model to the sale of all the heating plants. Last year, a major German company Verbundnetz Gas declared its interest in purchasing large municipal heating plants in Slovakia. But it has been waiting for a response ever since. The French company - Dalkia, which has 10-years' experience of doing business in Slovakia, is interested in all the heating plants to be offered for sale. The Austrian company - Stefe is not new to the business either, it is interested mainly in the regions where it has already established itself - Central and Eastern Slovakia. Strategic investors expect financial groups to show interest too. The Penta Group has not hid its ambitions - it has already privatised a company which represents the key to the future development of heat management in Bratislava - Paroplynovy cyklus. Whereas Penta is not new to the heat production business another financial group - Slavia Capital is still surveying the sector. Should it not succeed, it plans several projects that would allow it to take a stake in the sector

  18. Workshop on electroweak symmetry breaking: proceedings

    International Nuclear Information System (INIS)

    Hinchliffe, I.

    1984-10-01

    A theoretical workshop on electroweak symmetry breaking at the Superconducting Supercollider was held at Lawrence Berkeley Laboratory, June 4-22, 1984. The purpose of the workshop was to focus theoretical attention on the ways in which experimentation at the SSC could reveal manifestations of the phenomenon responsible for electroweak symmetry breaking. This issue represents, at present, the most compelling scientific argument for the need to explore the energy region to be made accessible by the SSC, and a major aim of the workshop was to involve a broad cross section of particle theorists in the ongoing process of sharpening the requirements for both accelerator and detector design that will ensure detection and identification of meaningful signals, whatever form the electroweak symmetry breaking phenomenon should actually take. Separate entries were prepared for the data base for the papers presented

  19. Workshop on electroweak symmetry breaking: proceedings

    Energy Technology Data Exchange (ETDEWEB)

    Hinchliffe, I. (ed.)

    1984-10-01

    A theoretical workshop on electroweak symmetry breaking at the Superconducting Supercollider was held at Lawrence Berkeley Laboratory, June 4-22, 1984. The purpose of the workshop was to focus theoretical attention on the ways in which experimentation at the SSC could reveal manifestations of the phenomenon responsible for electroweak symmetry breaking. This issue represents, at present, the most compelling scientific argument for the need to explore the energy region to be made accessible by the SSC, and a major aim of the workshop was to involve a broad cross section of particle theorists in the ongoing process of sharpening the requirements for both accelerator and detector design that will ensure detection and identification of meaningful signals, whatever form the electroweak symmetry breaking phenomenon should actually take. Separate entries were prepared for the data base for the papers presented.

  20. A break in the obesity epidemic?

    DEFF Research Database (Denmark)

    Visscher, T L S; Heitmann, B L; Rissanen, A

    2015-01-01

    epidemic. However, follow-ups of short duration may, in part, explain the apparent break or decrease in the obesity epidemic. On the other hand, a single focus on body mass index (BMI) ⩾25 or ⩾30 kg m(-)(2) is likely to mask a real increase in the obesity epidemic. And, in both children and adults, trends......Recent epidemiologic papers are presenting prevalence data suggesting breaks and decreases in obesity rates. However, before concluding that the obesity epidemic is not increasing anymore, the validity of the presented data should be discussed more thoroughly. We had a closer look...... into the literature presented in recent reviews to address the major potential biases and distortions, and to develop insights about how to interpret the presented suggestions for a potential break in the obesity epidemic. Decreasing participation rates, the use of reported rather than measured data and small sample...

  1. Breaking bad news in cancer patients.

    Science.gov (United States)

    Konstantis, Apostolos; Exiara, Triada

    2015-01-01

    In a regional hospital, many patients are newly diagnosed with cancer. Breaking the bad news in these patients and their relatives is a tough task. Many doctors are not experienced in talking to patients about death or death-related diseases. In recent years, there have been great efforts to change the current situation. The aim of this study was to investigate the experience and education of medical personnel in breaking bad news in a secondary hospital. 59 doctors from General Hospital of Komotini, Greece were included in the study. All the doctors were in clinical specialties that treated cancer patients. A brief questionnaire was developed based on current guidelines such as Baile/SPIKES framework and the ABCDE mnemonic. Residents are involved in delivering bad news less frequently than specialists. Only 21 doctors (35.59%) had specific training on breaking bad news. 20 doctors (33.90%) were aware of the available techniques and protocols on breaking bad news. 47 doctors (79.66%) had a consistent plan for breaking bad news. 57 (96.61%) delivered bad news in a quiet place, 53 (89.83%) ensured no interruptions and enough time, 53 (89.83%) used simple words and 54 (91.53%) checked for understanding and did not rush through the news. 46 doctors (77.97%) allowed relatives to determine patient's knowledge about the disease. There were low rates of specific training in breaking bad news. However, the selected location, the physician's speech and their plan were according to current guidelines.

  2. Breaking bad news in cancer patients

    Directory of Open Access Journals (Sweden)

    Apostolos Konstantis

    2015-01-01

    Full Text Available Objective: In a regional hospital, many patients are newly diagnosed with cancer. Breaking the bad news in these patients and their relatives is a tough task. Many doctors are not experienced in talking to patients about death or death-related diseases. In recent years, there have been great efforts to change the current situation. The aim of this study was to investigate the experience and education of medical personnel in breaking bad news in a secondary hospital. Materials and Methods: 59 doctors from General Hospital of Komotini, Greece were included in the study. All the doctors were in clinical specialties that treated cancer patients. A brief questionnaire was developed based on current guidelines such as Baile/SPIKES framework and the ABCDE mnemonic. Results: Residents are involved in delivering bad news less frequently than specialists. Only 21 doctors (35.59% had specific training on breaking bad news. 20 doctors (33.90% were aware of the available techniques and protocols on breaking bad news. 47 doctors (79.66% had a consistent plan for breaking bad news. 57 (96.61% delivered bad news in a quiet place, 53 (89.83% ensured no interruptions and enough time, 53 (89.83% used simple words and 54 (91.53% checked for understanding and did not rush through the news. 46 doctors (77.97% allowed relatives to determine patient′s knowledge about the disease. Conclusions: There were low rates of specific training in breaking bad news. However, the selected location, the physician′s speech and their plan were according to current guidelines.

  3. Implications of career break from personal and company perspectives

    OpenAIRE

    Vuorinen, Niina

    2017-01-01

    The objective of this study is to show the implications that career breaks have on individuals and employers. The intensions are to identify personal motivations for career breaks, and if the breaks change the careers of the people taking them. Furthermore, this study intends to understand how career breaks are viewed by employers, and if career breaks are becoming more acceptable internationally. The theoretical framework was based on description of work and careers both from employee an...

  4. Introduction to symmetry breaking and spin

    International Nuclear Information System (INIS)

    Ng, J.N.

    1992-05-01

    These lectures form an elementary introduction to the physics of symmetry breaking and the role polarization experiments play in the study of gauge symmetry breaking. Included here is an introduction to testing the electroweak sector of the standard model to one-loop and the use of oblique corrections as a probe of new physics. The second part of the lectures consists of an introduction to multiple Higgs models as sources of spontaneous CP violation. A brief discussion of using spin measurements in meson decays to study these sources of CP violation is also included. (author)

  5. Detecting Structural Breaks using Hidden Markov Models

    DEFF Research Database (Denmark)

    Ntantamis, Christos

    Testing for structural breaks and identifying their location is essential for econometric modeling. In this paper, a Hidden Markov Model (HMM) approach is used in order to perform these tasks. Breaks are defined as the data points where the underlying Markov Chain switches from one state to another....... The estimation of the HMM is conducted using a variant of the Iterative Conditional Expectation-Generalized Mixture (ICE-GEMI) algorithm proposed by Delignon et al. (1997), that permits analysis of the conditional distributions of economic data and allows for different functional forms across regimes...

  6. Electromagnetic radiation under explicit symmetry breaking.

    Science.gov (United States)

    Sinha, Dhiraj; Amaratunga, Gehan A J

    2015-04-10

    We report our observation that radiation from a system of accelerating charges is possible only when there is explicit breaking of symmetry in the electric field in space within the spatial configuration of the radiating system. Under symmetry breaking, current within an enclosed area around the radiating structure is not conserved at a certain instant of time resulting in radiation in free space. Electromagnetic radiation from dielectric and piezoelectric material based resonators are discussed in this context. Finally, it is argued that symmetry of a resonator of any form can be explicitly broken to create a radiating antenna.

  7. The experimental investigation of supersymmetry breaking

    Energy Technology Data Exchange (ETDEWEB)

    Peskin, M.E.

    1996-04-01

    If Nature is supersymmetric at the weak interaction scale, what can we hope to learn from experiments on supersymmetric particles? The most mysterious aspect of phenomenological supersymmetry is the mechanism of spontaneous supersymmetry breaking. This mechanism ties the observable pattern of supersymmetric particle masses to aspects of the underlying unified theory at very small distance scales. In this article, I will discuss a systematic experimental program to determine the mechanism of supersymmetry breaking. Both pp and e{sup +}e{sup -} colliders of the next generation play an essential role.

  8. The experimental investigation of supersymmetry breaking

    International Nuclear Information System (INIS)

    Peskin, M.E.

    1996-04-01

    If Nature is supersymmetric at the weak interaction scale, what can we hope to learn from experiments on supersymmetric particles? The most mysterious aspect of phenomenological supersymmetry is the mechanism of spontaneous supersymmetry breaking. This mechanism ties the observable pattern of supersymmetric particle masses to aspects of the underlying unified theory at very small distance scales. In this article, I will discuss a systematic experimental program to determine the mechanism of supersymmetry breaking. Both pp and e + e - colliders of the next generation play an essential role

  9. Peaking cladding temperature and break equivalent size of intermediate break loss of coolant accident

    International Nuclear Information System (INIS)

    Luo Bangqi

    2012-01-01

    The analysis results of intermediate break loss of coolant accident for the nuclear power plant of million kw level showed to be as following: (1) At the begin of life, the break occur simultaneity reactor shutdown with L(X)P. it's equivalent break size and peaking cladding temperature is respectively 20 cm and 849℃. (2) At the begin of life, the break occur simultaneity reactor shutdown without loop. the reactor coolant pumps will be stop after reactor shutdown 10 minutes, it's equivalent break size and peaking cladding temperature is respectively 10.5 cm and 921℃. (3) At the bur up of 31 GWd/t(EOC1). the break occur simultaneity reactor shutdown without loop, the reactor coolant pumps will be stop after reactor shutdown 20 minutes, it's equivalent break size and peaking cladding temperature is respectively 8 cm and 1145℃. The above analysis results showed that the peaking cladding temperature of intermediate break loss of coolant accident is not only related with the break equivalent size and core bur up, and is closely related with the stop time of coolant pumps because the coolant pumps would drive the coolant from safety system to produce the seal loop in break loop and affect the core coolant flow, results in the fuel cladding temperature increasing or damaging. Therefore, the break spectrum, burn up spectrum, the stop time of coolant pumps and operator action time will need to detail analysis and provide appropriate operating procedure, otherwise the peaking cladding temperature will exceed 1204℃ and threaten the safety of the reactor core when the intermediate break loss of coolant accident occur in some break equivalent size, burn up, stop pumps time and operator action not appropriate. The pressurizer pressure low signal simultaneity containment pressure higher signal were used as the operator manual close the signal of reactor coolant pumps after reactor shutdown of 20 minutes. have successful solved the operator intervention time from 10 minutes

  10. Remote Sensing Characteristics of Wave Breaking Rollers

    Science.gov (United States)

    Haller, M. C.; Catalan, P.

    2006-12-01

    The wave roller has a primary influence on the balances of mass and momentum in the surf zone (e.g. Svendsen, 1984; Dally and Brown, 1995; Ruessink et al., 2001). In addition, the roller area and its angle of inclination on the wave front are important quantities governing the dissipation rates in breaking waves (e.g Madsen et al., 1997). Yet, there have been very few measurements published of individual breaking wave roller geometries in shallow water. A number of investigators have focused on observations of the initial jet-like motion at the onset of breaking before the establishment of the wave roller (e.g. Basco, 1985; Jansen, 1986), while Govender et al. (2002) provide observations of wave roller vertical cross-sections and angles of inclination for a pair of laboratory wave conditions. Nonetheless, presently very little is known about the growth, evolution, and decay of this aerated region of white water as it propagates through the surf zone; mostly due to the inherent difficulties in making the relevant observations. The present work is focused on analyzing observations of the time and space scales of individual shallow water breaking wave rollers as derived from remote sensing systems. Using a high-resolution video system in a large-scale laboratory facility, we have obtained detailed measurements of the growth and evolution of the wave breaking roller. In addition, by synchronizing the remote video with in-situ wave gages, we are able to directly relate the video intensity signal to the underlying wave shape. Results indicate that the horizontal length scale of breaking wave rollers differs significantly from the previous observations of Duncan (1981), which has been a traditional basis for roller model parameterizations. The overall approach to the video analysis is new in the sense that we concentrate on individual breaking waves, as opposed to the more commonly used time-exposure technique. In addition, a new parameter of interest, denoted Imax, is

  11. Does artificial UV use prior to spring break protect students from sunburns during spring break?

    Science.gov (United States)

    Dennis, Leslie K; Lowe, John B

    2013-06-01

    Dark-skinned individuals are less likely than light-skinned individuals to become sunburned or develop skin cancer. Some have extrapolated this relationship and surmised that developing and maintaining a tan will reduce the risk of sunburns and melanoma. In order to examine whether this strategy indeed protects against sunburns, we surveyed college students about both their tanning habits prior to spring break and their spring break activities. Sorority and fraternity students were recruited after spring break. Analyses examined associations between potential risk factors and the development of one or more sunburns during spring break. As expected, the risk of obtaining a sunburn increased with: time spent in the sun during spring break; light complexion, as assessed by various sun-sensitivity factors; and lack of sunscreen use. We also found that tanning using an artificial UV source during the 10 weeks prior to spring break was not associated with reduced risk of sunburns during spring-break, but rather with a marginal increase in this risk. These data provide evidence that maintaining a tan may not provide protection from sunburns. Public health messages need to address this misconception, stating clearly that a tan does not protect against or reduce the chances of developing a sunburn. © 2013 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

  12. Atmospheric noise of a breaking tidal bore.

    Science.gov (United States)

    Chanson, Hubert

    2016-01-01

    A tidal bore is a surge of waters propagating upstream in an estuary as the tidal flow turns to rising and the flood tide propagates into a funnel-shaped system. Large tidal bores have a marked breaking roller. The sounds generated by breaking tidal bores were herein investigated in the field (Qiantang River) and in laboratory. The sound pressure record showed two dominant periods, with some similarity with an earlier study [Chanson (2009). J. Acoust. Soc. Am. 125(6), 3561-3568]. The two distinct phases were the incoming tidal bore when the sound amplitude increased with the approaching bore, and the passage of the tidal bore in front of the microphone when loud and powerful noises were heard. The dominant frequency ranged from 57 to 131 Hz in the Qiantang River bore. A comparison between laboratory and prototype tidal bores illustrated both common features and differences. The low pitch sound of the breaking bore had a dominant frequency close to the collective oscillations of bubble clouds, which could be modeled with a bubble cloud model using a transverse dimension of the bore roller. The findings suggest that this model might be over simplistic in the case of a powerful breaking bore, like that of the Qiantang River.

  13. Dynamical Symmetry Breaking in RN Quantum Gravity

    Directory of Open Access Journals (Sweden)

    A. T. Kotvytskiy

    2011-01-01

    Full Text Available We show that in the RN gravitation model, there is no dynamical symmetry breaking effect in the formalism of the Schwinger-Dyson equation (in flat background space-time. A general formula for the second variation of the gravitational action is obtained from the quantum corrections hμν (in arbitrary background metrics.

  14. Duality and supersymmetry breaking in string theory

    Energy Technology Data Exchange (ETDEWEB)

    Ferrara, S. (European Organization for Nuclear Research, Geneva (Switzerland) California Univ., Los Angeles (USA)); Magnoli, N.; Veneziano, G. (European Organization for Nuclear Research, Geneva (Switzerland)); Taylor, T.R. (Northeastern Univ., Boston, MA (USA))

    1990-08-16

    Target-space duality is incorporated in previously proposed effective actions describing non-perturbative supersymmetry breaking in string theory via gaugino condensation. Duality-preserving vacua with broken supersymmetry and fixed unified coupling constant do generically occur. The question of the vanishing of the cosmological constant is also briefly addressed. (orig.).

  15. Physician-patient communication: breaking bad news.

    Science.gov (United States)

    Fields, Scott A; Johnson, W Michael

    2012-01-01

    Physicians often struggle with how to manage the task of breaking bad news with patients. Moreover, the arduous nature of the task can contribute to physician detachment from the patient or an avoidance of breaking the news in a timely manner. A plan of action can only improve physician confidence in breaking bad news, and also make the task more manageable. Over a decade ago, Rabow and McPhee offered a strategy; the ABCDE plan, which provided a patient centered framework from which to deliver troubling news to patients and families. At the heart of this plan was the creation of a safe environment, the demonstration of timely communication skills, and the display of empathy on the physician's part. Careful consideration of the doctor's own reactions to death and dying also played an important role. A close review of the five tenets of this plan indicates the relevance of Rabow and McPhee's strategy today. The patient base in our nation and state continues to be older, on average, and physicians are faced with numerous patients who have terminal illness. A constructive plan with specific ideas for breaking bad news can help physicians effectively navigate this difficult task.

  16. Bereavement Part 2: Breaking bad news.

    Science.gov (United States)

    Kendrick, K D

    1998-11-01

    Breaking bad news, whether telling a patient about a poor prognosis or informing relatives of the sudden death of a loved one, is one of the most daunting tasks facing nurses. It requires a sensitive approach, based on individuals' right to know the truth.

  17. Density Functional Simulation of a Breaking Nanowire

    DEFF Research Database (Denmark)

    Nakamura, A.; Brandbyge, Mads; Hansen, Lars Bruno

    1999-01-01

    We study the deformation and breaking of an atomic-sized sodium wire using density functional simulations. The wire deforms through sudden atomic rearrangements and smoother atomic displacements. The conductance of the wire exhibits plateaus at integer values in units of 2e(2)/h corresponding...

  18. Firm break-up and performance

    Czech Academy of Sciences Publication Activity Database

    Kočenda, Evžen; Hanousek, Jan

    2012-01-01

    Roč. 13, č. 2 (2012), s. 121-143 ISSN 1435-6104 R&D Projects: GA ČR GA402/09/1595 Institutional support: PRVOUK-P23 Keywords : break-up of firms * corporate performance * ownership changes Subject RIV: AH - Economics Impact factor: 0.588, year: 2012

  19. Path-breaking books in regional science

    NARCIS (Netherlands)

    Waldorf, BS

    This article presents a collection of regional science books that long-standing members of the Regional Science Association International (RSAI) identified as path-breaking books. The most frequently nominated books include the "classics" by Isard, the seminal books in urban economics by Alonso,

  20. The issue of supersymmetry breaking in strings

    International Nuclear Information System (INIS)

    Binetruy, P.

    1989-12-01

    We discuss the central role that supersymmetry plays in string models, both in spacetime and at the level of the string world-sheet. The problems associated with supersymmetry-breaking are reviewed together with some of the attempts to solve them, in the string as well as the field theory approach

  1. Critical wind speed at which trees break

    Science.gov (United States)

    Virot, E.; Ponomarenko, A.; Dehandschoewercker, É.; Quéré, D.; Clanet, C.

    2016-02-01

    Data from storms suggest that the critical wind speed at which trees break is constant (≃42 m /s ), regardless of tree characteristics. We question the physical origin of this observation both experimentally and theoretically. By combining Hooke's law, Griffith's criterion, and tree allometry, we show that the critical wind speed indeed hardly depends on the height, diameter, and elastic properties of trees.

  2. Fragmentation in DNA double-strand breaks

    International Nuclear Information System (INIS)

    Wei Zhiyong; Suzhou Univ., Suzhou; Zhang Lihui; Li Ming; Fan Wo; Xu Yujie

    2005-01-01

    DNA double strand breaks are important lesions induced by irradiations. Random breakage model or quantification supported by this concept is suitable to analyze DNA double strand break data induced by low LET radiation, but deviation from random breakage model is more evident in high LET radiation data analysis. In this work we develop a new method, statistical fragmentation model, to analyze the fragmentation process of DNA double strand breaks. After charged particles enter the biological cell, they produce ionizations along their tracks, and transfer their energies to the cells and break the cellular DNA strands into fragments. The probable distribution of the fragments is obtained under the condition in which the entropy is maximum. Under the approximation E≅E 0 + E 1 l + E 2 l 2 , the distribution functions are obtained as exp(αl + βl 2 ). There are two components, the one proportional to exp(βl 2 ), mainly contributes to the low mass fragment yields, the other component, proportional to exp(αl), decreases slowly as the mass of the fragments increases. Numerical solution of the constraint equations provides parameters α and β. Experimental data, especially when the energy deposition is higher, support the statistical fragmentation model. (authors)

  3. Mechanisms of supersymmetry breaking in the minimal ...

    Indian Academy of Sciences (India)

    We provide a bird's eyeview of current ideas on supersymmetry breaking mechanisms in the MSSM. The essentials of gauge, gravity, anomaly and gaugino/higgsino mediation mechanisms are covered briefly and the phenomenology of the associated models is touched upon. A few statement are also made on braneworld ...

  4. SUSY breaking mediation by throat fields

    International Nuclear Information System (INIS)

    Bruemmer, F.; Hebecker, A.; Trapletti, M.

    2006-01-01

    We investigate, in the general framework of KKLT, the mediation of supersymmetry breaking by fields propagating in the strongly warped region of the compactification manifold ('throat fields'). Such fields can couple both to the supersymmetry breaking sector at the IR end of the throat and to the visible sector at the UV end. We model the supersymmetry breaking sector by a chiral superfield which develops an F term vacuum expectation value (also responsible for the uplift). It turns out that the mediation effect of vector multiplets propagating in the throat can compete with modulus-anomaly mediation. Moreover, such vector fields are naturally present as the gauge fields arising from isometries of the throat (most notably the SO(4) isometry of the Klebanov-Strassler solution). Their mediation effect is important in spite of their large 4d mass. The latter is due to the breaking of the throat isometry by the compact manifold at the UV end of the throat. The contribution from heavy chiral superfields is found to be subdominant

  5. Mechanisms of supersymmetry breaking in the minimal ...

    Indian Academy of Sciences (India)

    Preliminary remarks. This will be a somewhat theoretical review of models and mechanisms for generating soft explicit supersymmetry breaking terms in the MSSM. There will not be much signal phe- nomenology except in a few illustrative cases. Also, I shall be somewhat antihistorical in first talking about gauge mediation ...

  6. Electroweak symmetry breaking beyond the Standard Model

    Indian Academy of Sciences (India)

    In this paper, two key issues related to electroweak symmetry breaking are addressed. First, how fine-tuned different models are that trigger this phenomenon? Second, even if a light Higgs boson exists, does it have to be necessarily elementary? After a brief introduction, the fine-tuning aspects of the MSSM, NMSSM, ...

  7. Unified gauge theories with spontaneous symmetry breaking

    International Nuclear Information System (INIS)

    MacDowell, S.W.

    1975-01-01

    Unified gauge theories with spontaneous symmetry breaking are studied with a view to renormalize quantum field theory. Georgi-Glashow and Weinberg-Salam models to unify weak and electromagnetic interactions are discussed in detail. Gauge theories of strong interactions are also considered [pt

  8. Symmetry breaking and restoration in gauge theories

    International Nuclear Information System (INIS)

    Natale, A.A.

    A review is made of the utilization of the Higgs mechanism in spontaneous symmetry breaking. It is shown that such as ideas came from an analogy with the superconductivity phenomenological theory based on a Ginzburg-Landau lagrangean. The symmetry restoration through the temperature influence is studied. (L.C.) [pt

  9. Autologous Immune Enhancement Therapy for cancer using NK cells and CTLs without feeder layers; our six year experience in India

    Directory of Open Access Journals (Sweden)

    Dedeepiya V

    2011-01-01

    Full Text Available Background: Autologous Natural Killer (NK cells and Cytotoxic T Lymphocytes (CTLs based immune-cell therapy, otherwise called as Autologous Immune enhancement therapy (AIET, though has been in clinical practice in several developed nations since early 90s, in India it is in infancy due to lack of technological knowhow. Our institute has been providing the AIET cell expansion services since 2005 and we here in report our experience in 30 such patients of both solid tumours and hematological malignancies.Materials and Methods: The number of AIET transfusions in each patient ranged from one to six. All the patients included had Stage III to IV malignancy. AIET was either given along with the chemotherapy or after the completion of a minimum of six cycles of chemotherapy in all the patients. 70 ml of Peripheral Blood was collected each time. The protocol followed was as per Terunuma et al (Breast Cancer 2010 which uses only the patients’ autologous plasma for expansion of the Natural Killer Cells and Cytotoxic T lymphocytes from the peripheral blood. The cells were cultured for a period of 10 to 16 days and then transfused to the patients intravenously. The cells were subjected to Flow cytometry before and after the in vitro expansion. Feeder layers were not used in the procedure of in vitro expansion at any stage.Results: The percentage of NK cells and CTLs after expansion by flow cytometry ranged from 60 to 82 %. There were no adverse reactions in any of the patients following transfusion. The mean prolonged survival time was 15 months and 27% of the patients had Static non-progressive disease after the therapy. Two patients reported significant decrease in Cancer marker levels after AIET and among the terminally ill, two had more than two years survival. All the patients reported improvement in quality of life and resumption of appetite following AIET. Conclusion: Optimal in vitro expansion of NK cells and CTLs of patients with stage III

  10. Influence ofde qion the immediate analgesic effect of SP6 acupuncture in patients with primary dysmenorrhoea andcold and dampness stagnation: a multicentre randomised controlled trial.

    Science.gov (United States)

    Zhao, Min-Yi; Zhang, Peng; Li, Jing; Wang, Lin-Peng; Zhou, Wei; Wang, Yan-Xia; She, Yan-Fen; Ma, Liang-Xiao; Wang, Pei; Hu, Ni-Juan; Lin, Chi; Hu, Shang-Qin; Wu, Gui-Wen; Wang, Ya-Feng; Sun, Jun-Jun; Jiang, Si-Zhu; Zhu, Jiang

    2017-10-01

    The aim of this multicentre randomised controlled trial was to investigate the contribution of de qi to the immediate analgesic effect of acupuncture in patients with primary dysmenorrhoea and the specific traditional Chinese medicine diagnosis cold and dampness stagnation . Eighty-eight patients with primary dysmenorrhoea and cold and dampness stagnation were randomly assigned to de qi (n=43) or no de qi (n=45) groups and underwent 30 min of SP6 acupuncture. The de qi group received deep needling at SP6 with manipulation using thick needles; the no de qi group received shallow needling with no manipulation using thin needles. In both groups the pain scores and actual de qi sensation were evaluated using a visual analogue scale for pain (VAS-P) and the acupuncture de qi clinical assessment scale (ADCAS), respectively. Both groups showed reductions in VAS-P, with no signficant differences between groups. ADCAS scores showed 43/43 and 25/45 patients in de qi and no de qi groups, respectively, actually experienced de qi sensation. Independent of original group allocation, VAS-P reductions associated with actual de qi (n=68) were greater than those without (28.4±18.19 mm vs 14.6±12.28 mm, p=0.008). This study showed no significant difference in VAS-P scores in patients with primary dysmenorrhoea and cold and dampness stagnation immediately after SP6 acupuncture designed to induce or avoid de qi sensation. Both treatments significantly reduced VAS-P relative to baseline. Irrespective of group allocation, patients experiencing actual de qi sensation demonstrated larger reductions in pain score relative to those without, suggesting greater analgesic effects. Chinese Clinical Trial Registry (ChiCTR-TRC-13003086); Results. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2017. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

  11. Biological nitrate transport in sediments on the Peruvian margin mitigates benthic sulfide emissions and drives pelagic N loss during stagnation events

    Science.gov (United States)

    Dale, A. W.; Sommer, S.; Lomnitz, U.; Bourbonnais, A.; Wallmann, K.

    2016-06-01

    Benthic N cycling in the Peruvian oxygen minimum zone (OMZ) was investigated at ten stations along 12 °S from the middle shelf (74 m) to the upper slope (1024 m) using in situ flux measurements, sediment biogeochemistry and modeling. Middle shelf sediments were covered by mats of the filamentous bacteria Thioploca spp. and contained a large 'hidden' pool of nitrate that was not detectable in the porewater. This was attributed to a biological nitrate reservoir stored within the bacteria to oxidize sulfide during 'dissimilatory nitrate reduction to ammonium' (DNRA). The extremely high rates of DNRA on the shelf (15.6 mmol m-2 d-1 of N), determined using an empirical steady-state model, could easily supply all the ammonium requirements for anammox in the water column. The model further showed that denitrification by foraminifera may account for 90% of N2 production at the lower edge of the OMZ. At the time of sampling, dissolved oxygen was below detection limit down to 400 m and the water body overlying the shelf had stagnated, resulting in complete depletion of nitrate and nitrite. A decrease in the biological nitrate pool was observed on the shelf during fieldwork concomitant with a rise in porewater sulfide levels in surface sediments to 2 mM. Using a non-steady state model to simulate this natural anoxia experiment, these observations were shown to be consistent with Thioploca surviving on a dwindling intracellular nitrate reservoir to survive the stagnation period. The model shows that sediments hosting Thioploca are able to maintain high ammonium fluxes for many weeks following stagnation, potentially sustaining pelagic N loss by anammox. In contrast, sulfide emissions remain low, reducing the economic risk to the Peruvian fishery by toxic sulfide plume development.

  12. Breaking bad news among cancer physicians

    Directory of Open Access Journals (Sweden)

    Sami Ayed Alshammary

    2017-01-01

    Full Text Available Background: Breaking bad news to patients with cancer diagnosis is not an easy task for physicians. The diagnosis must be explicitly stated and understood, and prognosis must be well-discussed in the most gentle and comfortable manner. It is important that the disclosure is performed in a way that patients will not lose all hope and get very depressed, leading them to undergo an abrupt change of their outlook in life. Objective: The aim of this study was to explore the physicians' perceptions and perspectives of breaking bad news to cancer patients. Methods: A cross-sectional survey of all comprehensive cancer centre physicians currently working in a university teaching hospital in the Middle East was conducted from August to September 2016. Results: Sixty-eight percent responded to the survey. Eighty-four percent were comfortable with breaking bad news, and 70% had training in breaking bad news. Eighty-six percent of responders stated that patients should be told about their cancer. Almost 30% of the respondents stated that they would still disclose the diagnosis to patients even if it would be against the preference of the relatives. Nearly 61% said that they would only tell the details to the patients if asked while 67% of them disagreed that patients should be told about the diagnoses only if the relatives consent. About 51% of physicians wanted to discuss the bad news with the family members and patient together, whereas 24% stated that the patient alone should be involved in the discussion. Conclusion: Physicians face a dilemma when families do not wish the patient to know the cancer diagnosis and this highlights the necessity of taking into consideration the social circumstances in healthcare. When taking these into considerations, curriculum in the medical school must, therefore, be updated and must integrate the acquisition of skills in breaking bad news early in training.

  13. Quantum break-time of de Sitter

    Science.gov (United States)

    Dvali, Gia; Gómez, César; Zell, Sebastian

    2017-06-01

    The quantum break-time of a system is the time-scale after which its true quantum evolution departs from the classical mean field evolution. For capturing it, a quantum resolution of the classical background—e.g., in terms of a coherent state—is required. In this paper, we first consider a simple scalar model with anharmonic oscillations and derive its quantum break-time. Next, following [1], we apply these ideas to de Sitter space. We formulate a simple model of a spin-2 field, which for some time reproduces the de Sitter metric and simultaneously allows for its well-defined representation as quantum coherent state of gravitons. The mean occupation number N of background gravitons turns out to be equal to the de Sitter horizon area in Planck units, while their frequency is given by the de Sitter Hubble parameter. In the semi-classical limit, we show that the model reproduces all the known properties of de Sitter, such as the redshift of probe particles and thermal Gibbons-Hawking radiation, all in the language of quantum S-matrix scatterings and decays of coherent state gravitons. Most importantly, this framework allows to capture the 1/N-effects to which the usual semi-classical treatment is blind. They violate the de Sitter symmetry and lead to a finite quantum break-time of the de Sitter state equal to the de Sitter radius times N. We also point out that the quantum-break time is inversely proportional to the number of particle species in the theory. Thus, the quantum break-time imposes the following consistency condition: older and species-richer universes must have smaller cosmological constants. For the maximal, phenomenologically acceptable number of species, the observed cosmological constant would saturate this bound if our Universe were 10100 years old in its entire classical history.

  14. Stagnation point flow of third-grade liquid due to variable thickness: A useful application to non-Fourier heat flux approach

    Science.gov (United States)

    Zubair, M.; Waqas, M.; Hayat, T.; Alsaedi, A.; Ayub, M.

    2018-03-01

    The impact of modified Fourier's relation in non-linear mixed convective flow of third grade liquid is examined in this article. Stagnation point flow is considered. Variable thermal conductivity and thermal stratification are examined. Non-Fourier heat flux in heat transfer process is retained. Convergent local similar solutions for the nonlinear differential systems are achieved by homotopic procedure. Skin friction is computed and analyzed. Our computations certifies that velocity is higher when nonlinear convection and local buoyancy parameters are augmented. However temperature and thermal layer thickness are reduced for larger thermal relaxation factor.

  15. New optical method for heat flux measurements in stagnation point laminar methane/air flames and hydrogen/methane/air flames using thermographic phosphors

    Energy Technology Data Exchange (ETDEWEB)

    Elmnefi, Mohamed Salem

    2010-11-24

    In the present study, a new optical method was implemented to study the heat transfer from flat stagnation point flames which can be regarded as one-dimensional in the central part. Premixed methane-air flames and hydrogen-methane-air flames were investigated. The effects of burner-to-plate distance and the fresh gas mixture velocity on heat transfer were examined. Experiments were performed using light induced phosphorescence from thermographic phosphors to study the wall temperatures and heat fluxes of nearly one-dimensional flat premixed flames impinging upward normally on a horizontal water cooled circular flat plate. The investigated flames were stoichiometric, lean and rich laminar methane/air flames with different equivalence ratios of {phi} =1, {phi} = 0.75 and {phi} = 1.25 and stoichiometric laminar hydrogen/methane/air flames. Mixtures of air with 10, 25, 50 and 75 % hydrogen in methane (CH{sub 4}) as well as a pure hydrogen flames at ambient pressure were investigated. The central part of this plate was an alumina ceramic plate coated from both sides with chromium doped alumina (ruby) and excited with a Nd:YAG laser or a green light emitting diode (LED) array to measure the wall temperature from both sides and thus the heat flux rate from the flame. The outlet velocity of the gases was varied from 0.1 m/s to 1.2 m/s. The burner to plate distance ranged from 0.5 to 2 times the burner exit diameter (d = 30 mm).The accuracy of the method was evaluated. The measured heat flux indicate the change of the flame stabilization mechanism from a burner stabilized to a stagnation plate stabilized flame. The results were compared to modeling results of a one dimensional stagnation point flow, with a detailed reaction mechanism. In order to prove the model, also measured gas phase temperatures by OH LIF for a stoichiometric stagnation point flame were discussed. It turns out that the flame stabilization mechanism and with it the heat fluxes change from low to high

  16. Feeding rates and under-ice foraging strategies of the smallest lunge filter feeder, the Antarctic minke whale (Balaenoptera bonaerensis).

    Science.gov (United States)

    Friedlaender, A S; Goldbogen, J A; Nowacek, D P; Read, A J; Johnston, D; Gales, N

    2014-08-15

    Body size and feeding mode are two fundamental characteristics that determine foraging performance and ecological niche. As the smallest obligate lunge filter feeders, minke whales represent an ideal system for studying the physical and energetic limits of filter feeding in endotherms. We used multi-sensor suction cup tags to quantify the feeding performance of Antarctic minke whales. Foraging dives around and beneath sea ice contained up to 24 lunges per dive, the highest feeding rates for any lunge-feeding whale. Their small size allows minke whales access to krill in sea-ice environments not easily accessible to larger baleen whales. Furthermore, their ability to filter feed provides an advantage over other smaller sympatric krill predators such as penguins and seals that feed on individual prey. The unique combination of body size, feeding mechanism and sea-ice habitat of Antarctic minke whales defines a previously undocumented energetic niche that is unique among aquatic vertebrates. © 2014. Published by The Company of Biologists Ltd.

  17. From steep feeders to tabular plutons - Emplacement controls of syntectonic granitoid plutons in the Damara Belt, Namibia

    Science.gov (United States)

    Hall, Duncan; Kisters, Alexander

    2016-01-01

    Granitoid plutons in the deeply eroded south Central Zone of the Damara Belt in Namibia commonly show tabular geometries and pronounced stratigraphic controls on their emplacement. Subhorizontal, sheet-like pluton geometries record emplacement during regional subhorizontal shortening, but the intrusion of spatially and temporally closely-related granitoid plutons at different structural levels and in distinct structural settings suggests independent controls on their levels of emplacement. We describe and evaluate the controls on the loci of the dyke-to-sill transition that initiated the emplacement of three syntectonic (560-530 Ma) plutons in the basement-cover stratigraphy of the Erongo region. Intrusive relationships highlight the significance of (1) rigidity anisotropies associated with competent sedimentary packages or pre-existing subhorizontal granite sheets and (2) rheological anisotropies associated with the presence of thick ductile marble horizons. These mechanical anisotropies may lead to the initial deflection of steep feeder conduits as well as subsequent pluton assembly by the repeated underaccretion of later magma batches. The upward displacement of regional isotherms due to the heat advection associated with granite emplacement is likely to have a profound effect on the mechanical stratification of the upper crust and, consequently, on the level at which granitoid pluton emplacement is initiated. In this way, pluton emplacement at progressively shallower crustal depths may have resulted in the unusually high apparent geothermal gradients recorded in the upper crustal levels of the Damara Belt during its later evolution.

  18. Modelling mid-crustal migmatite terrains as feeder zones for granite plutons: the competing dynamics of melt transfer by bulk versus porous flow

    OpenAIRE

    Olsen, Sakiko N.; Marsh, Bruce D.; Baumgartner, Lukas P.

    2017-01-01

    The common association of mid-crustal migmatites with an upper-level granite pluton could indicate that the migmatites are a feeder zone for the pluton. If magma from a deeper level pervasively intrudes a high temperature metamorphic complex, most of the intruded magma would not freeze because of the prevailing temperature. The interaction between the magma and country rocks, which could include partial melting and crystallisation of the magma passing through, would modify magma to a more gra...

  19. THE METHOD OF SELECTION OF THE SETPOINT HIGH SPEED FEEDER SWITCH OF 3,3KV DC WITH MICROPROCESSOR-BASED PROTECTION SYSTEMS

    Directory of Open Access Journals (Sweden)

    P. Ye. Mykhalichenko

    2009-10-01

    Full Text Available In the article a new procedure of choice of minimum current jump for action of fast-acting switches of 3.3 kV DC traction substations intended for the use in the microprocessor protection system of feeders is described. This procedure is more perfect than existing one on the current increment and uses the results of mathematical simulation of the traction electric supply system.

  20. Evaluation of human MRC-5 cells as a feeder layer in a xenobiotic-free culture system for conjunctival epithelial progenitor cells.

    Science.gov (United States)

    Schrader, Stefan; Tuft, Stephen J; Beaconsfield, Michele; Borrelli, Maria; Geerling, Gerd; Daniels, Julie T

    2012-12-01

    Aim of this study was to evaluate the efficiency of human MRC-5 cells to act as a feeder layer for conjunctival epithelial cells in order to develop a complete xenobiotic-free culture system for the expansion of conjunctival epithelial progenitor cells for clinical applications. Human conjunctival epithelial cells were expanded from a bulbar biopsy, in a completely xenobiotic-free culture system using growth arrested MRC-5 cells as a feeder layer, without (MRC-5/No Serum) and in the presence of 5% (MRC-5/HS 5%) or 10% (MRC-5/HS 10%) human serum. The total cell count, the surface area as well as the total colony-forming efficiency (CFE), the percentage of aborted colonies and the expression of putative progenitor cell markers p63α, ABCG2, CK15 was compared to the gold standard culture system (GS) in which growth arrested 3T3 feeder cells and feotal calf serum were used. The epithelial cell count revealed significantly less proliferation in the MRC-5/No Serum group compared to the GS conditions. All groups showed immunoreactivity to CK19; however, more differentiated epithelial cells were observed in the MRC-5/No Serum- and MRC-5/HS 10%-group and less immunoreactivity to p63 α and ABCG2 was found in these groups compared to GS and MRC-5/HS 5% conditions. This was in accordance with CFE results, were the MRC-5/HS 5% group showed similar CFE results compared to the GS group, while in the MRC-5/No Serum- and MRC-5/HS 10%-group significantly lower CFE's were observed. Our results indicate that a completely xenobiotic-free culture system using MRC-5 cells as a feeder layer in combination with human serum can be successfully used to expand conjunctival epithelial cells with progenitor cell characteristics and might be a useful tool for the safe expansion of these cells for clinical use.

  1. Thermophysical analysis for three-dimensional MHD stagnation-point flow of nano-material influenced by an exponential stretching surface

    Directory of Open Access Journals (Sweden)

    Fiaz Ur Rehman

    2018-03-01

    Full Text Available In the present paper a theoretical investigation is performed to analyze heat and mass transport enhancement of water-based nanofluid for three dimensional (3D MHD stagnation-point flow caused by an exponentially stretched surface. Water is considered as a base fluid. There are three (3 types of nanoparticles considered in this study namely, CuO (Copper oxide, Fe3O4 (Magnetite, and Al2O3 (Alumina are considered along with water. In this problem we invoked the boundary layer phenomena and suitable similarity transformation, as a result our three dimensional non-linear equations of describing current problem are transmuted into nonlinear and non-homogeneous differential equations involving ordinary derivatives. We solved the final equations by applying homotopy analysis technique. Influential outcomes of aggressing parameters involved in this study, effecting profiles of temperature field and velocity are explained in detail. Graphical results of involved parameters appearing in considered nanofluid are presented separately. It is worth mentioning that Skin-friction along x and y-direction is maximum for Copper oxide-water nanofluid and minimum for Alumina-water nanofluid. Result for local Nusselt number is maximum for Copper oxide-water nanofluid and is minimum for magnetite-water nanofluid. Keywords: Heat transfer, Nanofluids, Stagnation-point flow, Three-dimensional flow, Nano particles, Boundary layer

  2. Minimising the risk of water hammer and other problems at the beginning of stagnation of solar thermal plants - A theoretical approach

    International Nuclear Information System (INIS)

    Streicher, W.

    2000-01-01

    Solar plants are increasingly used not only for hot tap water heating but also for the assistance of space heating. These plants produce much more energy in summer than needed, which often results in stagnation. Because of stagnation-temperatures of todays selective collectors up to 200 deg. C, the collector fluid evaporates. In several plants a high noise level and a vibration of the plant during this evaporation phase is reported. This is due to the occurrence of water hammers in the system, when liquid collector fluid passes areas where the fluid was already evaporated and superheated. The remaining vapor bubbles deflate rapidly and the liquid phases collide with high velocity, which results in a rapid pressure increase. This paper describes the theory of condensate-induced water hammers and conditions of solar plants, under which this can happen. A simulation model for the evaporation phase of the collector is presented to give a deeper understanding about the influences of solar radiation, the size of the tubing, and the size of the expansion device on the process of the evaporation. Three hydraulic layouts of the collector area are discussed for there possibilities producing water hammers. (au)

  3. Breaking Bad News in Veterinary Medicine.

    Science.gov (United States)

    Nickels, Bonnie McCracken; Feeley, Thomas Hugh

    2017-06-16

    The patient-provider relationship in the context of veterinary medicine represents a unique opportunity for studying how bad news is communicated to pet owners by conducting structured interviews with veterinarians. A sample of 44 veterinarians' responses was recorded and content-analyzed in an effort to identify themes among providers in their clinical experience of breaking bad news (BBN). Two coders revealed several themes in the data that were organized by three overarching areas: (1) breaking bad news in general, (2) euthanasia, and (3) social support. The findings from interviews indicated the COMFORT model (Villagran, Goldsmith, Wittenberg-Lyles, & Baldwin, 2010) in medical education provided a useful framework to organize the communication of BBN in veterinary medicine. Results were discussed in relation to future research in patient-provider communication and COMFORT's potential value for training students in veterinarian education.

  4. Dual realizations of dynamical symmetry breaking

    International Nuclear Information System (INIS)

    Dudas, Emilian; Papineau, Chloe

    2006-01-01

    We show the infrared equivalence between a recently proposed model containing a six dimensional scalar field with a four-dimensional localized Higgs type potential and the four-dimensional Nambu-Jona-Lasinio (NJL) model. In the dual NJL description, the fermions are localized at the origin of a large two-dimensional compact space. Due to a classical running effect above the compactification scale, the four-fermion coupling of the NJL model increases from the cutoff scale down to the compactification scale, providing the large Fermi coupling needed for the dynamical symmetry breaking. We also present a string theory embedding of our field-theory construction. On more general grounds, our results suggest that 4d models with dynamical symmetry breaking can be given a higher dimensional description in terms of field theories with nontrivial boundary conditions in the internal space

  5. [Breaking bad news in clinical practice].

    Science.gov (United States)

    Herrera, Andrea; Ríos, Matías; Manríquez, José Manuel; Rojas, Gonzalo

    2014-10-01

    Breaking bad news is a complex task that requires multiple communication skills from health professionals. Clinical practice demands to communicate all type of bad news, from a diagnosis of cancer to adverse effects of a treatment. On the other hand, since the beginning of the health reform in 2003, the need to improve the quality of services was proposed, among which the concern about the rights and duties of patients stands out. Therefore, the health care provider-patient relationship becomes again the subject of discussion and study, and a topic of great importance for clinical work. We revise the consequences of breaking bad news for the patient and for the health care provider, as well as the current protocols available for this purpose. The importance of developing communication skills both for future health professionals as for those who currently work in the area is emphasized.

  6. Unit roots, nonlinearities and structural breaks

    DEFF Research Database (Denmark)

    Haldrup, Niels; Kruse, Robinson; Teräsvirta, Timo

    One of the most influential research fields in econometrics over the past decades concerns unit root testing in economic time series. In macro-economics much of the interest in the area originate from the fact that when unit roots are present, then shocks to the time series processes have...... a selective review of contributions to the field of unit root testing over the past three decades. We discuss the nature of stochastic and deterministic trend processes, including break processes, that are likely to affect unit root inference. A range of the most popular unit root tests are presented...... and their modifications to situations with breaks are discussed. We also review some results on unit root testing within the framework of non-linear processes....

  7. Electroweak symmetry breaking: Higgs/whatever

    International Nuclear Information System (INIS)

    Chanowitz, M.S.

    1989-01-01

    In the first of these two lectures the Higgs mechanism is reviewed in its most general form, which does not necessarily require the existence of Higgs bosons. The general consequences of the hypothesis that electroweak symmetry breaking is due to the Higgs mechanism are deduced just from gauge invariance and unitarity. In the second lecture the general properties are illustrated with three specific models: the Weinberg-Salam model, its minimal supersymmetric extension, and technicolor. The second lecture concludes with a discussion of the experiment signals for strong WW scattering, whose presence or absence will allow us to determine whether the symmetry breaking sector lies above or below 1 TeV. 57 refs

  8. Mechanochemical symmetry breaking in Hydra aggregates.

    Science.gov (United States)

    Mercker, Moritz; Köthe, Alexandra; Marciniak-Czochra, Anna

    2015-05-05

    Tissue morphogenesis comprises the self-organized creation of various patterns and shapes. Although detailed underlying mechanisms are still elusive in many cases, an increasing amount of experimental data suggests that chemical morphogen and mechanical processes are strongly coupled. Here, we develop and test a minimal model of the axis-defining step (i.e., symmetry breaking) in aggregates of the Hydra polyp. Based on previous findings, we combine osmotically driven shape oscillations with tissue mechanics and morphogen dynamics. We show that the model incorporating a simple feedback loop between morphogen patterning and tissue stretch reproduces a wide range of experimental data. Finally, we compare different hypothetical morphogen patterning mechanisms (Turing, tissue-curvature, and self-organized criticality). Our results suggest the experimental investigation of bigger (i.e., multiple head) aggregates as a key step for a deeper understanding of mechanochemical symmetry breaking in Hydra. Copyright © 2015 The Authors. Published by Elsevier Inc. All rights reserved.

  9. Selecting a model of supersymmetry breaking mediation

    International Nuclear Information System (INIS)

    AbdusSalam, S. S.; Allanach, B. C.; Dolan, M. J.; Feroz, F.; Hobson, M. P.

    2009-01-01

    We study the problem of selecting between different mechanisms of supersymmetry breaking in the minimal supersymmetric standard model using current data. We evaluate the Bayesian evidence of four supersymmetry breaking scenarios: mSUGRA, mGMSB, mAMSB, and moduli mediation. The results show a strong dependence on the dark matter assumption. Using the inferred cosmological relic density as an upper bound, minimal anomaly mediation is at least moderately favored over the CMSSM. Our fits also indicate that evidence for a positive sign of the μ parameter is moderate at best. We present constraints on the anomaly and gauge mediated parameter spaces and some previously unexplored aspects of the dark matter phenomenology of the moduli mediation scenario. We use sparticle searches, indirect observables and dark matter observables in the global fit and quantify robustness with respect to prior choice. We quantify how much information is contained within each constraint.

  10. Analysis of chiral symmetry breaking mechanism

    Energy Technology Data Exchange (ETDEWEB)

    Xin-Heng, Guo [Centro Brasileiro de Pesquisas Fisicas (CBPF), Rio de Janeiro, RJ (Brazil); Tao, Huang [Academia Sinica, Beijing, BJ (China). Inst. of High Energy Physics; Chuang, Wang

    1997-07-01

    The renormalization group invariant quark condensate {mu} is determinate both from the consistent equation for quark condensate in the chiral limit and from the Schwinger-Dyson (SD) equation improved by the intermediate range QCD force singular like {delta} (q) which is associated with the gluon condensate. The solutions of {mu} in these two equations are consistent. We also obtain the critical strong coupling constant {alpha}c above which chiral symmetry breaks in two approaches. The nonperturbative kernel of the SD equation makes {alpha}c smaller and {mu} bigger. An intuitive picture of the condensation above {alpha}c is discussed. In addition, with the help of the Slavnov-Taylor-Ward (STW) identity we derive the equations for the nonperturbative quark propagator from SD equation in the presence of the intermediate-range force is also responsible for dynamical chiral symmetry breaking. (author) 32 refs., 2 figs.

  11. Dynamics of Symmetry Breaking and Tachyonic Preheating

    CERN Document Server

    Felder, G; Greene, P B; Kofman, L A; Linde, Andrei D; Tkachev, Igor I; Felder, Gary; Garcia-Bellido, Juan; Greene, Patrick B.; Kofman, Lev; Linde, Andrei; Tkachev, Igor

    2001-01-01

    We reconsider the old problem of the dynamics of spontaneous symmetry breaking using 3d lattice simulations, and develop a theory of tachyonic preheating, which occurs due to the spinodal instability of the scalar field. Tachyonic preheating is so efficient that symmetry breaking typically completes within a single oscillation of the field distribution as it rolls towards the minimum of its effective potential. As an application of this theory we consider preheating in the hybrid inflation scenario, including SUSY-motivated F-term and D-term inflationary models. We show that preheating in hybrid inflation is typically tachyonic and the stage of oscillations of a homogeneous component of the scalar fields driving inflation ends after a single oscillation. Our results may also be relevant for the theory of the formation of disoriented chiral condensates in heavy ion collisions.

  12. Qinshan NPP large break LOCA safety analysis

    International Nuclear Information System (INIS)

    Shi Guobao; Tang Jiahuan; Zhou Quanfu; Wang Yangding

    1997-01-01

    Qinshan NPP is the first nuclear power plant in the mainland of China, a 300 MW(e) two-loop PWR. Large break LOCA is the design-basis accident of Qinshan NPP. Based on available computer codes, the own analysis method which complies with Appendix k of 10 CFR 50 has been established. The RELAP4/MOD7 code is employed for the calculations of blowdown, refill and reflood phase of the RCS respectively. The CONTEMPT-LT/028 code is used for the containment pressure and temperature analysis. The temperature transient in the hot rod is calculated using the FRAP-6T code. Conservative initial and functional assumptions were adopted during Qinshan NPP large break LOCA analysis. The results of the analysis show the applicable acceptance criteria for the loss-of-coolant accident are met

  13. Use of repellents for honeybees (Apis mellifera L. in vitro in the yellow passion-fruit (Passiflora edulis Deg crop and in confined beef cattle feeders

    Directory of Open Access Journals (Sweden)

    D. Nicodemo

    2004-01-01

    Full Text Available The presence of Apis mellifera in places such as candy and soft drink factories, restaurants, and ice-cream shops has been a concern to many people. In the yellow passion-fruit crop, Apis mellifera is able to collect all anther pollen but has no active role in pollination. Honeybees also visit animal feeders with chopped sugar cane, preventing the cattle from eating. This work studied the effect of natural and synthetic substances as Apis mellifera repellents in vitro in the yellow passion-fruit crop and in confined beef cattle feeders. There was a repellent effect in vitro with the following substances in decreasing order: tobacco, rue, garlic, parsley, and century plant extracts; average effect was twenty-five minutes. For the yellow passion-fruit, garlic extracts and 2-heptanone were equally efficient with a two and a half hour repellent action. Garlic and citronella extracts were efficient in repelling Apis mellifera from confined beef cattle feeder for six hours. Garlic repellent action was higher than citronella.

  14. A Frequency-Based Assignment Model under Day-to-Day Information Evolution of Oversaturated Conditions on a Feeder Bus Service

    Directory of Open Access Journals (Sweden)

    Silin Zhang

    2017-02-01

    Full Text Available Day-to-day information is increasingly being implemented in transit networks worldwide. Feeder bus service (FBS plays a vital role in a public transit network by providing feeder access to hubs and rails. As a feeder service, a space-time path for frequent passengers is decided by its dynamic strategy procedure, in which a day-to-day information self-learning mechanism is identified and analyzed from our survey data. We formulate a frequency-based assignment model considering day-to-day evolution under oversaturated conditions, which takes into account the residual capacity of bus and the comfort feelings of sitting or standing. The core of our proposed model is to allocate the passengers on each segment belonging to their own paths according to multi-utilities transformed from the time values and parametric demands, such as frequency, bus capacity, seat comfort, and stop layout. The assignment method, albeit general, allows us to formulate an equivalent optimization problem in terms of interaction between the FBS’ operation and frequent passengers’ rational behaviors. Finally, a real application case is generated to test the ability of the modeling framework capturing the theoretical consequents, serving the passengers’ dynamic externalities.

  15. The fern-feeder aphids (Hemiptera: Aphididae) from China: a generic account, descriptions of one new genus, one new species, one new subspecies, and keys.

    Science.gov (United States)

    Su, Xiao-Mei; Jiang, Li-Yun; Qiao, Ge-Xia

    2014-02-11

    Fern-feeder aphids (Hemiptera: Aphididae) in China are represented by 13 species in 10 genera, including a new genus, Vietaphis gen nov., a new species, Vietaphis aliquantus sp nov., from Guizhou and Tibet on Plagiogyria japonicum, and a new subspecies, Amphorophora scabripes galba ssp nov., from Guizhou on Pentarhizidium intermedium. Two genera, Amphorophora Buckton and Idiopterus Davis, and four species or subspecies, Amphorophora ampullate ben-galensis Hille Ris Lambers and Basu, Idiopterus nephrelepidis Davis, Micromyzodium polypodii Takahashi, and Myzus filicis Basu, are reported for the first time in China. Apterae and alatae of Myzus filicis are redescribed herein, and with host plant notes. The fern-feeder aphid genus Ne-omacromyzus Lee is considered a junior synonym of Idiopterus. Furthermore, Neomacromyzus cyrtomicola Lee is transferred to the genus Idiopterus, as Idiopterus cyrtomicola (Lee), comb nov., which is herein considered a junior synonym of Idiopterus nephrelepidis Davis. Keys to Chinese fern-feeder species are provided. Morphological figures and biometrical data of Vietaphis aliquantus sp nov., Amphorophora scabripes galba ssp nov., and Myzus filicis are presented. This is an open access paper. We use the Creative Commons Attribution 3.0 license that permits unrestricted use, provided that the paper is properly attributed.

  16. Microwave-assisted rock breaking modelling and application

    CSIR Research Space (South Africa)

    Monchusi, B

    2012-10-01

    Full Text Available As part of the ongoing development of novel mining methods, the CSIR has developed alternative methods to break rocks. In this case, we show the application of microwave energy to break narrow tabular ore bodies....

  17. Breaking democracy with non renormalizable mass terms

    CERN Document Server

    Silva-Marcos, Joaquim I

    2001-01-01

    The exact democratic structure for the quark mass matrix, resulting from the action of the family symmetry group $A_{3L}\\times A_{3R}$, is broken by the vacuum expectation values of heavy singlet fields appearing in non renormalizable dimension 6 operators. Within this specific context of breaking of the family symmetry we formulate a very simple ansatz which leads to correct quark masses and mixings.

  18. Dynamical symmetry breaking in quantum field theories

    CERN Document Server

    Miransky, Vladimir A

    1993-01-01

    The phenomenon of dynamical symmetry breaking (DSB) in quantum field theory is discussed in a detailed and comprehensive way. The deep connection between this phenomenon in condensed matter physics and particle physics is emphasized. The realizations of DSB in such realistic theories as quantum chromodynamics and electroweak theory are considered. Issues intimately connected with DSB such as critical phenomenona and effective lagrangian approach are also discussed.

  19. Supersymmetry breaking in a magnetic field

    International Nuclear Information System (INIS)

    Akyeampong, D.A.

    1981-10-01

    The one-loop effective potential of an abelian supersymmetric model in an environment provided by a constant external magnetic field is derived. It is shown that magnetic field breaks supersymmetry and that the value of the resulting minimum potential is lower than that of the tree level. This could be relevant to the question of possible restoration of the symmetry at higher loops. (author)

  20. Music and Video Gaming during Breaks

    OpenAIRE

    Liu, Shuyan; Schad, Daniel J.; Kuschpel, Maxim S.; Rapp, Michael A.; Heinz, Andreas

    2016-01-01

    Different systems for habitual versus goal-directed control are thought to underlie human decision-making. Working memory is known to shape these decision-making systems and their interplay, and is known to support goal-directed decision making even under stress. Here, we investigated if and how decision systems are differentially influenced by breaks filled with diverse everyday life activities known to modulate working memory performance. We used a within-subject design where young adult...