WorldWideScience

Sample records for feasibility study technical

  1. Technical feasibility study on polycarbonate solar panels

    NARCIS (Netherlands)

    Hackmann, M.M.; Meuwissen, M.H.H.; Bots, T.L.; Buijs, J.A.H.M.; Broek, K.M.; Kinderman, R.; Tanck, O.B.F.; Schuurmans, F.M.

    2004-01-01

    This paper describes a technical feasibility study on the application of polycarbonate (PC) plates in a superstrate photovoltaic module design. The lamination process was performed in a conventional laminator apparatus using low temperature curing (100°C) ethylene-vinyl-acetate (EVA) as the potting

  2. Economic and technical feasibility study of compressed air storage

    Energy Technology Data Exchange (ETDEWEB)

    1976-03-01

    The results of a study of the economic and technical feasibility of compressed air energy storage (CAES) are presented. The study, which concentrated primarily on the application of underground air storage with combustion turbines, consisted of two phases. In the first phase a general assessment of the technical alternatives, economic characteristics and the institutional constraints associated with underground storage of compressed air for utility peaking application was carried out. The goal of this assessment was to identify potential barrier problems and to define the incentive for the implementation of compressed air storage. In the second phase, the general conclusions of the assessment were tested by carrying out the conceptual design of a CAES plant at two specific sites, and a program of further work indicated by the assessment study was formulated. The conceptual design of a CAES plant employing storage in an aquifer and that of a plant employing storage in a conventionally excavated cavern employing a water leg to maintain constant pressure are shown. Recommendations for further work, as well as directions of future turbo-machinery development, are made. It is concluded that compressed air storage is technically feasible for off-peak energy storage, and, depending on site conditions, CAES plants may be favored over simple cycle turbine plants to meet peak demands. (LCL)

  3. Technical Feasibility Study for Zero Energy K-12 Schools

    Energy Technology Data Exchange (ETDEWEB)

    Bonnema, Eric [National Renewable Energy Lab. (NREL), Golden, CO (United States); Goldwasser, David [National Renewable Energy Lab. (NREL), Golden, CO (United States); Torcellini, Paul [National Renewable Energy Lab. (NREL), Golden, CO (United States); Pless, Shanti [National Renewable Energy Lab. (NREL), Golden, CO (United States); Studer, Daniel [National Renewable Energy Lab. (NREL), Golden, CO (United States)

    2016-11-01

    This technical feasibility study provides documentation and research results supporting a possible set of strategies to achieve source zero energy K-12 school buildings as defined by the U.S. Department of Energy (DOE) zero energy building (ZEB) definition (DOE 2015a). Under this definition, a ZEB is an energy-efficient building in which, on a source energy basis, the actual annual delivered energy is less than or equal to the on-site renewable exported energy.

  4. Economical and technical feasibility study of some radioisotopes production for medical application

    International Nuclear Information System (INIS)

    Souza, A.L.A.B. de.

    1985-01-01

    The economical and technical feasibility study of the production in reactors of some radioisotopes most used in medicine, are presented. The clinical applications of each radioisotope as well as its radioactive concentrations and specific activities are related. Irradiation procedures based in the foregoing data are given. Part of the study is dedicated to quality control. (M.A.C.) [pt

  5. Technical Analysis Feasibility Study on Smart Microgrid System in Sekolah Tinggi Teknik PLN

    Science.gov (United States)

    Suyanto, Heri

    2018-02-01

    Nowadays application of new and renewable energy as main resource of power plant has greatly increased. High penetration of renewable energy into the grid will influence the quality and reliability of the electricity system, due to the intermittent characteristic of new and renewable energy resources. Smart grid or microgrid technology has the ability to deal with this intermittent characteristic especially if these renewable energy resources integrated to grid in large scale, so it can improve the reliability and efficiency of the grid. We plan to implement smart microgrid system at Sekolah Tinggi Teknik PLN as a pilot project. Before the pilot project start, the feasibility study must be conducted. In this feasibility study, the renewable energy resources and load characteristic at the site will be measured. Then the technical aspect of this feasibility study will be analyzed. This paper explains that analysis of ths feasibility study.

  6. Technical and economic feasibility study for the creation of a tissue bank

    International Nuclear Information System (INIS)

    Loncomilla Sandoval, Andrea Rosi; Mendez Guerra, Karina Angelica

    2006-01-01

    The risk of getting contagious illnesses through applying biological tissues has been one of the paramount worries to be solved since infectious illnesses might be provoked by virus, fungi or bacteria coming from donors or whether they have been introduced by means of intermediate stages before the use of these tissues. Therefore it has been concluded that the tissue allograft must be sterilized. The work presented is a Technical and economic Feasibility Study for the creation of a Tissue Bank in Chile, considering the fact of lacking of such institutions in our country and the need to satisfy the population that requires tissues. It is shown the processes involved and the characteristics of a tissue bank, and also a market survey in order to meet the demand, supply, technical requirements, competitors, opportunities and legal aspects of the process. Finally, it was examined the economic feasibility at which defines the investment, financing and business projections to determine the profitability of the project

  7. Technical feasibility of advanced separation; Faisabilite technique de la separation poussee

    Energy Technology Data Exchange (ETDEWEB)

    Rostaing, Ch

    2004-07-01

    Advanced separation aims at reducing the amount and toxicity of high-level and long lived radioactive wastes. The Purex process has been retained as a reference way for the recovery of the most radio-toxic elements: neptunium, technetium and iodine. Complementary solvent extraction processes have to be developed for the separation of americium, curium and cesium from the high activity effluent of the spent fuel reprocessing treatment. Researches have been carried out with the aim of demonstrating the scientifical and technical feasibility of advanced separation of minor actinides and long lived fission products from spent fuels. The scientifical feasibility was demonstrated at the end of 2001. The technical feasibility works started in the beginning of 2002. Many results have been obtained which are presented and summarized in this document: approach followed, processes retained for the technical feasibility (An/Ln and Am/Cm separation), processes retained for further validation at the new shielded Purex installation, technical feasibility of Purex adaptation to Np separation, technical feasibility of Diamex (first step: (An+Ln)/other fission products) separation), technical feasibility of Sanex process (second step: An(III)/Ln(III) separation), technical feasibility of Am(III)/Cm(III) separation, cesium separation, iodine separation, technical-economical evaluation, conclusions and perspectives, facilities and apparatuses used for the experiments. (J.S.)

  8. Performance and technical feasibility comparison of reusable launch systems: A synthesis of the ESA winged launcher studies

    Science.gov (United States)

    Berry, W.; Grallert, H.

    1996-02-01

    The paper presents a synthesis of the performance and technical feasibility assessment of 7 reusable launcher types, comprising 13 different vehicles, studied by European Industry for ESA in the ESA Winged Launcher Study in the period January 1988 to May 1994. The vehicles comprised single-stage-to-orbit (SSTO) and two-stage-to-orbit (TSTO) vehicles, propelled by either air-breathing/rocket propulsion or entirely by rocket propulsion. The results showed that an SSTO vehicle of the HOTOL-type, propelled by subsonic combustion air-breathing/rocket engines could barely deliver the specified payload mass and was aerodynamically unstable; that a TSTO vehicle of the Saenger type, employing subsonic combustion airbreathing propulsion in its first stage and rocket propulsion in its second stage, could readily deliver the specified payload mass and was found to be technically feasible and versatile; that an SSTO vehicle of the NASP type, propelled by supersonic combustion airbreathing/rocket propulsion was able to deliver a reduced payload mass, was very complex and required very advanced technologies; that an air-launched rocket propelled vehicle of the Interim HOTOL type, although technically feasible, could deliver only a reduced payload mass, being constrained by the lifting capability of the carrier airplane; that three different, entirely rocket-propelled vehicles could deliver the specified payload mass, were technically feasible but required relatively advanced technologies.

  9. Tuna cannery energy conservation interventions: Technical/economic feasibility study

    Energy Technology Data Exchange (ETDEWEB)

    Florio, G. (Calabria Univ. Arcavacata di Rende (Italy). Dipt. di Meccanica)

    An energy audit was conducted on a 230,000 can (x 80 g)/day tuna cannery to determine where technically and economically feasible energy savings interventions could be made. The plant is equipped with an oil fired boiler which supplies steam for cooking and sterilization purposes. In the energy/cost analysis, it was found that the most significant and cost effective energy savings could be obtained by the substitution of the four sterilization chambers with three sets of twin sterilization/heat exchange chambers.

  10. Technical feasibility study of 60 MWe fast reactor concept: RAPID

    International Nuclear Information System (INIS)

    Kambe, Mitsuru; Ueda, Nobuyuki; Uotani, Masaki

    1993-01-01

    A study has been performed on the passive safety features and technical feasibility of an inherently safe 60 MWe fast reactor concept RAPID to meet various power requirements in Japan. The system dynamic analyses on the UTOP and ULOF transients revealed that the enhanced reactivity feedback derived from an annular core configuration and the integrated fuel assembly provides a high margin of self-protection. Structural integrity of the integrated fuel assembly has also been confirmed. The following innovative key technologies have been demonstrated; Lithium Injection Modules (LIM) for ultimate shutdown, Lithium Expansion Modulus (LEM) for inherent reactivity feedback and Void Leading Channel (VLC) for the sodium void worth reduction. (author)

  11. Status of feasibility study for various technical options of FBR systems

    International Nuclear Information System (INIS)

    Kani, Yoshio

    2000-01-01

    JNC (Japan Nuclear Cycle Development Institute) has started a new research project of feasibility studies (F/S) for a wide variety option of fast breeder reactor (FBR) and related fuel cycle in order to develop an economically competitive FBR cycle system fro commercialization. JNC and the electric untilities in Japan have established a new organization in JNC to perform the F/S since July 1, 1999. The organization has undertaken feasibility studies (F/S) in order to determine promising FBR cycle concepts and define necessary RandD tasks. The long-term targets of commercialized FBR cycle system are set as ensuring safety, economic competitiveness relative to future LWRs, efficient utilization of resources, reduction in environmental burden, and enhancement of nuclear non-proliferation. This paper describes the progress of design studies for a wide variety of technical options of FBR plants in the framework of the F/S. We make efforts towards considering all key issues so as not to fail to notice the best concept in a commercialized stage. In the study of technical options, the identified coolant types are sodium, heavy metal (lead and lead-bismuth), gas (carbon dioxide and helium ) and water (boiling water, pressurized water and supercritical water). The classified types of fuel are mixed oxide, nitride and metal. Design studies of small size modular plant concepts are also performed. We study many reactor concepts in combination with a coolant type and a fuel type, understand characteristics of each reactor concept based on our experience and an extensive survey of literature, and make a draft design of each reactor concept for rough estimation of construction costs. We also check how far the concept accomplishes each index (safety, economy, resource utilization, etc.) of design requirements, and will select several promising reactor concepts. (author)

  12. Biogas Koczala. Biogas project in Koczala. Feasibility study. Technical report

    International Nuclear Information System (INIS)

    2004-08-01

    The present production of district heating in Koczala is based on coal. The district heating system is worn out technically and economically and according to the 2001 Energy Plan of Koczala the district heating plant shall be converted to a combination of a biogas fired CHP and a wood chip boiler. The overall objective of this project is to access the feasibility and viability construction an operation of a biogas plant owned by the co-operative agricultural company, Poldanor S.A. The feasibility study includes: 1) Availability of organic waste in the Koczala area, 2) Possibilities of using energy crops in the biogas plant, 3) Possibilities of receiving grants from the Polish National Fund for Environmental Protection, the new EU regional funds and through the joint implementation market (CO 2 quotas), 4) Alternative locations of the biogas plant and the CHP unit, 5) Alternative strategies for selling electricity and heat, 6) Organisational issues (ownership). This report concludes that implementing the biogas project is environmentally and financially feasible and viable. If organic waste and/or maize silage can be provided and gasified without problems, the plant can supply as well the Koczala farm as the fodder mill with steam and heat, and also supply Koczala district heating system with approx. 75% of yearly heat consumption. Furthermore, electricity is supplied to the fodder mill and the public grid. (BA)

  13. A Feasibility Study for Consolidating and/or Coordinating Technical Procedures in Beaver County Pennsylvania Libraries.

    Science.gov (United States)

    Fry, James W.

    In 1977 the Public Library Commission, in conjunction with the State Library of Pennsylvania, received a Library Services and Construction Act, Title III Grant to conduct a feasibility study of technical service operations in various types of libraries within Beaver County. Its objectives were to: (1) analyze existing library materials purchasing…

  14. Feasibility study

    International Nuclear Information System (INIS)

    Gibbs, P.; Kalas, P.

    1975-01-01

    The feasibility study itself examines the technical, economic and financial implications of a nuclear power station in depth so as to make sure that nuclear power is the right course to take. This means that it is quite an expensive operation and it is to avoid wasting this money that a pre-feasibility study is carried out. This preliminary study should eliminate cases where the electrical system cannot absorb the capacity of a nuclear station of commercial size, where other sources of power such as hydro-electricity, gas or cheap coal would make nuclear obviously uneconomic or where no suitable sites exist. If this first rather simple survey shows that nuclear power is a credible solution to a utilities need for electricity or heat production plant, then the next stage is a full feasibility study. (orig./TK) [de

  15. A systematic framework for the feasibility and technical evaluation of reactive distillation processes

    NARCIS (Netherlands)

    Shah, M.R.; Kiss, A.A.; Zondervan, E.; Haan, de A.B.

    2012-01-01

    This study presents a novel design methodology for the feasibility and technical evaluation of reactive distillation (RD), and discusses the applicability of various design methods of RD. The proposed framework for the feasibility evaluation determines the boundary conditions (e.g. relative

  16. Technical design aspects of Feasibility Study-II

    International Nuclear Information System (INIS)

    Zisman, Michael S.

    2001-01-01

    Feasibility Study-II examined a high-performance Neutrino Factory providing 1 x 10 20 neutrinos per year aimed at a long-baseline detector. The Study was sponsored jointly by BNL and the Neutrino Factory and Muon Collider Collaboration ration (MC) and is based on a 1 MW proton driver operating at 24 GeV, i.e., an upgraded version of the AGS accelerator. Compared with the earlier FNAL-sponsored study (Feasibility Study-I), there is a sixfold improvement in performance. Here we describe details of the implementation of Study-II concepts and discuss their efficacy. Alternative approaches that will be pursued in follow-on R and D activities are also described briefly

  17. Technical feasibility study for a solar energy system at Amsterdam Airport Schiphol (AAS)

    NARCIS (Netherlands)

    Janssen, P.N.J.W.; Myrzik, J.M.A.; Kling, W.L.; Reinders, L.

    2010-01-01

    This work arises within the framework of the introduction of renewable energies at Amsterdam Airport Schiphol (AAS) and the focus is on the technical feasibility of a solar energy system (SES) on ground level. The flight safety must always be guaranteed if solar panels are implemented on AAS. The

  18. Technical Feasibility Study for Deployment of Ground-Source Heat Pump Systems: Portsmouth Naval Shipyard -- Kittery, Maine

    Energy Technology Data Exchange (ETDEWEB)

    Hillesheim, M.; Mosey, G.

    2014-11-01

    The U.S. Environmental Protection Agency (EPA) Office of Solid Waste and Emergency Response, in accordance with the RE-Powering America's Lands initiative, engaged the U.S. Department of Energy's (DOE) National Renewable Energy Laboratory (NREL) to conduct feasibility studies to assess the viability of developing renewable energy generating facilities on contaminated sites. Portsmouth Naval Shipyard (PNSY) is a United States Navy facility located on a series of conjoined islands in the Piscataqua River between Kittery, ME and Portsmouth, NH. EPA engaged NREL to conduct a study to determine technical feasibility of deploying ground-source heat pump systems to help PNSY achieve energy reduction goals.

  19. Ultrasound-Guided Intermediate Site Greater Occipital Nerve Infiltration: A Technical Feasibility Study.

    Science.gov (United States)

    Zipfel, Jonathan; Kastler, Adrian; Tatu, Laurent; Behr, Julien; Kechidi, Rachid; Kastler, Bruno

    2016-01-01

    Two studies recently reported that computed tomography (CT) guided infiltration of the greater occipital nerve at its intermediate site allows a high efficacy rate with long-lasting pain relief following procedure in occipital neuralgia and in various craniofacial pain syndromes. The purpose of our study was to evaluate the technical feasibility and safety of ultrasound-guided intermediate site greater occipital nerve infiltration. Retrospective study. This study was conducted at the imaging department of a 1,409 bed university hospital. Local institutional review board approval was obtained and written consent was waived. In this retrospective study, 12 patients suffering from refractory occipital neuralgia or craniofacial pain syndromes were included between April and October 2014. They underwent a total of 21 ultrasound-guided infiltrations. Infiltration of the greater occipital nerve was performed at the intermediate site of the greater occipital nerve, at its first bend between obliqus capitis inferior and semispinalis capitis muscles with local anestetics and cortivazol. Technical success was defined as satisfactory diffusion of added iodinated contrast media in the fatty space between these muscles depicted on control CT scan. We also reported first data of immediate block test efficacy and initial clinical efficacy at 7 days, one month, and 3 months, defined by a decrease of at least 50% of visual analog scale (VAS) scores. Technical success rate was 95.24%. Patients suffered from right unilateral occipital neuralgia in 3 cases, left unilateral occipital neuralgia in 2 cases, bilateral occipital neuralgia in 2 cases, migraine in one case, cervicogenic headache in one case, tension-type headache in 2 cases, and cluster headache in one case. Block test efficacy was found in 93.3% (14/15) cases. Clinical efficacy was found in 80% of cases at 7 days, in 66.7% of cases at one month and in 60% of cases at 3 months. No major complications were noted. Some of the

  20. Technical feasibility for commercialization of lithium ion battery as a substitute dry battery for motorcycle

    Science.gov (United States)

    Kurniyati, Indah; Sutopo, Wahyudi; Zakaria, Roni; Kadir, Evizal Abdul

    2017-11-01

    Dry battery on a motorcycle has a rapid rate of voltage drop, life time is not too long, and a long charging time. These are problems for users of dry battery for motorcycle. When the rate in the voltage decreases, the energy storage in the battery is reduced, then at the age of one to two years of battery will be dead and cannot be used, it makes the user should replace the battery. New technology development of a motorcycle battery is lithium ion battery. Lithium ion battery has a specification that has been tested and possible to replace dry battery. Characteristics of lithium ion battery can answer the question on the dry battery service life, the rate of decrease in voltage and charging time. This paper discusses about the technical feasibility for commercialization of lithium ion battery for motorcycle battery. Our proposed methodology of technical feasibility by using a goldsmith commercialization model of the technical feasibility and reconfirm the technical standard using the national standard of motorcycle battery. The battery has been through all the stages of the technical feasibility of the goldsmith model. Based on the results of the study, lithium ion batteries have the minimum technical requirements to be commercialized and has been confirmed in accordance with the standard motorcycle battery. This paper results that the lithium ion battery is visible to commercialized by the technical aspect.

  1. Feasibility assessment of a risk-based approach to technical specifications

    International Nuclear Information System (INIS)

    Atefi, B.; Gallagher, D.W.

    1991-05-01

    The first phase of the assessment concentrates on (1) identification of selected risk-based approaches for improving current technical specifications, (2) appraisal of characteristics of each approach, including advantages and disadvantages, and (3) recommendation of one or more approaches that might result in improving current technical specification requirements. The second phase of the work concentrates on assessment of the feasibility of implementation of a pilot program to study detailed characteristics of the preferred approach. The real time risk-based approach was identified as the preferred approach to technical specifications for controlling plant operational risk. There do not appear to be any technical or institutional obstacles to prevent initiation of a pilot program to assess the characteristics and effectiveness of such an approach. 2 tabs

  2. Sault Tribe Wind Energy Feasibility Study

    Energy Technology Data Exchange (ETDEWEB)

    Toni Osterhout; Global Energy Concepts

    2005-07-31

    The Sault Tribe conducted a feasibility study on tribal lands in the Upper Peninsula of Michigan to determine the technical and economic feasibility of both small and large-scale wind power development on tribal lands. The study included a wind resource assessment, transmission system analysis, engineering and regulatory analyzes and assessments.

  3. Study of technical, economic and environmental feasibility of industrial scale production of nanocellulose obtained from the agroindustrial wastes from pineapple peel (Ananas comosus)

    International Nuclear Information System (INIS)

    Camacho Elizondo, Melissa

    2013-01-01

    Technical, economic and environmental study is realized to determine the feasibility of the industrial production of nanocellulose, from agroindustrial wastes of pineapple (Ananas comosus) market oriented of plastic packaging. The market bibliographical studies (national and international) and real capacities of national institutions have determined the most adequate and competitive method for the production of nanocellulose. The conditions to produce nanocellulose are described from agroindustrial wastes of pineapple in an industrial scale, according with the predominant factors in the plastic market. The equilibrium point, cost and price of nanocellulose produced are analyzed for the national market of plastics. The producing unit implemented is evaluated within the general framework of national and international economy and market to contribute the conditions that may to affect the feasibility and profitability of the project. The technical study has demonstrated to count with the adequate technology for the project execution. The economic study of the project has indicated to be economically profitable, considering the results of the NPV ($ 110 031,73), IRR (46,42%) and MARR (19,19%). The SuperPro Designer program has been used as a tool to corroborate the results in the technical-economic study and these have shown that the project has been feasible [es

  4. Technical feasibility of krypton-85 storage in sodalite

    International Nuclear Information System (INIS)

    Benedict, R.W.; Christensen, A.B.; Del Debbio, J.A.; Keller, J.H.; Knecht, D.A.

    1979-01-01

    Based on these experimental results, the process that is technically feasible for a reference 2000 metric ton of heavy metal (MTHM) per year reprocessing plant producing approx. 17 MCi or approx. 190 m 3 at STP would encapsulate krypton at approx. 20 cm 3 /g from krypton at temperatures greater than 575 0 C and pressures greater than 1600 atm with one batch a day in a 58-L high pressure vessel. Based on preliminary measurements at 500 0 C, the same process also would be feasible for a 70% krypton and 30% xenon mixture. 7 figures

  5. Methanol production with elemental phosphorus byproduct gas: technical and economic feasibility

    Energy Technology Data Exchange (ETDEWEB)

    Lyke, S.E.; Moore, R.H.

    1981-01-01

    The technical and economic feasibility of using a typical, elemental, phosphorus byproduct gas stream in methanol production is assessed. The purpose of the study is to explore the potential of a substitute for natural gas. The first part of the study establishes economic tradeoffs between several alternative methods of supplying the hydrogen which is needed in the methanol synthesis process to react with CO from the off gas. The preferred alternative is the Battelle Process, which uses natural gas in combination with the off gas in an economically sized methanol plant. The second part of the study presents a preliminary basic design of a plant to (1) clean and compress the off gas, (2) return recovered phosphorus to the phosphorus plant, and (3) produce methanol by the Battelle Process. Use of elemental phosphorus byproduct gas in methanol production appears to be technically feasible. The Battelle Process shows a definite but relatively small economic advantage over conventional methanol manufacture based on natural gas alone. The process would be economically feasible only where natural gas supply and methanol market conditions at a phosphorus plant are not significantly less favorable than at competing methanol plants. If off-gas streams from two or more phosphorus plants could be combined, production of methanol using only offgas might also be economically feasible. The North American methanol market, however, does not seem likely to require another new methanol project until after 1990. The off-gas cleanup, compression, and phosphorus-recovery system could be used to produce a CO-rich stream that could be economically attractive for production of several other chemicals besides methanol.

  6. Renewable Energy Feasibility Study Final Report

    Energy Technology Data Exchange (ETDEWEB)

    Rooney, Tim [Antares Group Inc.

    2013-10-30

    The Gila River Indian Community (GRIC or the Community) contracted the ANTARES Group, Inc. (“ANTARES”) to assess the feasibility of solar photovoltaic (PV) installations. A solar energy project could provide a number of benefits to the Community in terms of potential future energy savings, increased employment, environmental benefits from renewable energy generation and usage, and increased energy self-sufficiency. The study addresses a number of facets of a solar project’s overall feasibility, including: Technical appropriateness; Solar resource characteristics and expected system performance; Levelized cost of electricity (LCOE) economic assessment. The Gila River Indian Community (GRIC or the Community) contracted the ANTARES Group, Inc. (“ANTARES”) to prepare a biomass resource assessment study and evaluate the feasibility of a bioenergy project on Community land. A biomass project could provide a number of benefits to the Community in terms of increased employment, environmental benefits from renewable energy generation and usage, and increased energy self-sufficiency. The study addresses a number of facets of a biomass project’s overall feasibility, including: Resource analysis and costs; Identification of potential bioenergy projects; Technical and economic (levelized cost of energy) modeling for selected project configuration.

  7. General discussion of feasibility study

    International Nuclear Information System (INIS)

    Calori, F.

    1976-01-01

    Fundamentals, objectives and parameters of feasibility studies in the field of nuclear power project planning are discussed in a general way. Technical and economic problems to be considered are pointed out. In special cases, IAEA offers its aid and support. (UA) [de

  8. White Earth Biomass/Biogas Feasibility Study

    Energy Technology Data Exchange (ETDEWEB)

    Triplett, Michael

    2015-03-12

    The White Earth Nation examined the feasibility of cost savings and fossil energy reduction through the installation of biogas/biomass boiler at the tribal casino. The study rejected biogas options due to availability and site constraints, but found a favorable environment for technical and financial feasibility of installing a 5 MMBtu hot water boiler system to offset 60-70 percent of current fuel oil and propane usage.

  9. Technical-economic feasibility of orbiting sunlight reflectors

    Science.gov (United States)

    Alferov, Z.; Minin, V.

    1986-02-01

    The use of deflectors in orbit as a means of providing artificial illumination is examined. Considerations of technical and economic feasibility are addressed. Three main areas of application are distinguished: reflecting sunlight onto the surface of the Earth; concentration of the flow of solar energy on an orbiting receiver; and retransmission of optical radiation. The advantages of the artificial Earth illumination application of the orbiting reflector scheme in terms of energy savings in lighting cities, and additional daylight time for critical periods of farming operations are discussed.

  10. Final Technical Report: Renewable Energy Feasibility Study and Resources Assessment

    Energy Technology Data Exchange (ETDEWEB)

    Rivero, Mariah [BEC Environmental, Inc., Las Vegas, NV (United States)

    2016-02-28

    In March 2011, the U.S. Department of Energy (DOE) awarded White Pine County, Nevada, a grant to assess the feasibility of renewable resource-related economic development activities in the area. The grant project included a public outreach and training component and was to include a demonstration project; however, the demonstration project was not completed due to lack of identification of an entity willing to locate a project in White Pine County. White Pine County completed the assessment of renewable resources and a feasibility study on the potential for a renewable energy-focused economic sector within the County. The feasibility study concluded "all resources studied were present and in sufficient quantity and quality to warrant consideration for development" and there were varying degrees of potential economic impact based on the resource type and project size. The feasibility study and its components were to be used as tools to attract potential developers and other business ventures to the local market. White Pine County also marketed the County’s resources to the renewable energy business community in an effort to develop contracts for demonstration projects. The County also worked to develop partnerships with local educational institutions, including the White Pine County School District, conducted outreach and training for the local community.

  11. Technical Feasibility Study of Thermal Energy Storage Integration into the Conventional Power Plant Cycle

    Directory of Open Access Journals (Sweden)

    Jacek D. Wojcik

    2017-02-01

    Full Text Available The current load balance in the grid is managed mainly through peaking fossil-fuelled power plants that respond passively to the load changes. Intermittency, which comes from renewable energy sources, imposes additional requirements for even more flexible and faster responses from conventional power plants. A major challenge is to keep conventional generation running closest to the design condition with higher load factors and to avoid switching off periods if possible. Thermal energy storage (TES integration into the power plant process cycle is considered as a possible solution for this issue. In this article, a technical feasibility study of TES integration into a 375-MW subcritical oil-fired conventional power plant is presented. Retrofitting is considered in order to avoid major changes in the power plant process cycle. The concept is tested based on the complete power plant model implemented in the ProTRAX software environment. Steam and water parameters are assessed for different TES integration scenarios as a function of the plant load level. The best candidate points for heat extraction in the TES charging and discharging processes are evaluated. The results demonstrate that the integration of TES with power plant cycle is feasible and provide a provisional guidance for the design of the TES system that will result in the minimal influence on the power plant cycle.

  12. Distributed Manufacturing of Flexible Products: Technical Feasibility and Economic Viability

    Directory of Open Access Journals (Sweden)

    Aubrey L. Woern

    2017-10-01

    Full Text Available Distributed manufacturing even at the household level is now well established with the combined use of open source designs and self-replicating rapid prototyper (RepRap 3-D printers. Previous work has shown substantial economic consumer benefits for producing their own polymer products. Now flexible filaments are available at roughly 3-times the cost of more conventional 3-D printing materials. To provide some insight into the potential for flexible filament to be both technically feasible and economically viable for distributed digital manufacturing at the consumer level this study investigates 20 common flexible household products. The 3-D printed products were quantified by print time, electrical energy use and filament consumption by mass to determine the cost to fabricate with a commercial RepRap 3-D printer. Printed parts were inspected and when necessary tested for their targeted application to ensure technical feasibility. Then, the experimentally measured cost to DIY manufacturers was compared to low and high market prices for comparable commercially available products. In addition, the mark-up and potential for long-term price declines was estimated for flexible filaments by converting thermoplastic elastomer (TPE pellets into filament and reground TPE from a local recycling center into filament using an open source recyclebot. This study found that commercial flexible filament is economically as well as technically feasible for providing a means of distributed home-scale manufacturing of flexible products. The results found a 75% savings when compared to the least expensive commercially equivalent products and 92% when compared to high market priced products. Roughly, 160 flexible objects must be substituted to recover the capital costs to print flexible materials. However, as previous work has shown the Lulzbot Mini 3-D printer used in this study would provide more than a 100% ROI printing one object a week from hard thermoplastics

  13. Technical Feasibility and Comprehensive Sustainability Assessment of Sweet Sorghum for Bioethanol Production in China

    Directory of Open Access Journals (Sweden)

    Xiaolin Yang

    2018-03-01

    Full Text Available Under dual pressures of energy and environmental security, sweet sorghum is becoming one of the most promising feedstocks for biofuel production. In the present study, the technical feasibility of sweet sorghum production was assessed in eight agricultural regions in China using the Sweet Sorghum Production Technique Maturity Model. Three top typical agricultural zones were then selected for further sustainability assessment of sweet sorghum production: Northeast China (NEC, Huang-Huai-Hai Basin (HHHB and Ganxin Region (GX. Assessment results demonstrated that NEC exhibited the best sustainable production of sweet sorghum, with a degree of technical maturity value of 0.8066, followed by HHHB and GX, with corresponding values of 0.7531 and 0.6594, respectively. Prospective economic profitability analysis indicated that bioethanol production from sweet sorghum was not feasible using current technologies in China. More efforts are needed to dramatically improve feedstock mechanization logistics while developing new bioethanol productive technology to reduce the total cost. This study provides insight and information to guide further technological development toward profitable industrialization and large-scale sweet sorghum bioethanol production.

  14. Technical economic feasibility study for the implementation of a nuclear power plant for the production of electricity in Colombia

    International Nuclear Information System (INIS)

    Gonzales, David E.; Bolanos, Hernan G.; Mayorga, Manuel A.; Rodriguez, Edwin A.

    2013-01-01

    A study on the technical and economic feasibility will be used to implement a nuclear power in Colombia to generate electricity. To this will be searched if there are previous studies on this topic and what they concluded. The manner in which power is supplied will be discussed in a national level nowadays, its strengths and weaknesses. It will be investigated the legal norms that exists in the country on nuclear power and renewable energy sources, the standards established at world level, the nuclear accidents and the great examples. Providers will be sought on the world market nuclear equipment which serve to this purpose and the technical characteristics of these equipment will be discussed. The type of fuel used in nuclear reactors, its origin, method of production, specifications, availability and long-term and safe handling and final disposal are considered. safe handling of this technology and policy or international rules that will studied

  15. Evaluation of the technical feasibility of new conditioning matrices for long-lived radionuclides

    International Nuclear Information System (INIS)

    Deschanels, X.

    2004-01-01

    Several matrices have been selected for the conditioning of long-lived radioactive wastes: a compound made of a iodo-apatite core coated with a densified matrice of vanadium-phosphorus-lead apatite for iodine; the hollandite ceramic for cesium; the britholite, zirconolite, thorium phosphate diphosphate, and the monazite-brabantite solid solution for minor actinides; and a Nb-based metal alloy and phosphate or titanate-type ceramics for technetium. This report presents the results of the researches carried out between 2002-2004 during the technical feasibility step. The main points described are: - the behaviour of matrices under irradiation. These studies were performed thanks to an approach combining the characterization of natural analogues, the doping of matrices with short-lived radionuclides and the use of external irradiations; - the behaviour of these matrices with respect to water alteration; - the sensibility of these structures with respect to the incorporation of chemical impurities; - a package-process approach including the optimization of the process and preliminary studies about the package concept retained. These studies show that important work remains to be done to develop conditioning matrices suitable for iodine and technetium, while for cesium and minor actinides, the first steps of the technical feasibility are made. However, it remains impossible today to determine the structure having the best global behaviour. (J.S.)

  16. Toward feasible, valid, and reliable video-based assessments of technical surgical skills in the operating room

    DEFF Research Database (Denmark)

    Aggarwal, R.; Grantcharov, T.; Moorthy, K.

    2008-01-01

    .72). Conclusions: Video-based technical skills evaluation in the operating room is feasible, valid and reliable. Global rating scales hold promise for summative assessment, though further work is necessary to elucidate the value of procedural rating scales Udgivelsesdato: 2008/2......Objective: To determine the feasibility, validity, inter-rater, and intertest reliability of 4 previously published video-based rating scales, for technical skills assessment on a benchmark laparoscopic procedure. Summary Background Data: Assessment of technical skills is crucial...... to the demonstration and maintenance of competent healthcare practitioners. Traditional assessment methods are prone to subjectivity through a lack of proven validity and reliability. Methods: Nineteen surgeons (6 novice and 13 experienced) performed a median of 2 laparoscopic cholecystectomies each (range 1-5) on 53...

  17. Replacing fossil based plastic performance products by bio-based plastic products-Technical feasibility.

    Science.gov (United States)

    van den Oever, Martien; Molenveld, Karin

    2017-07-25

    Larger scale market introduction of new bio-based products requires a clear advantage regarding sustainability, as well as an adequate techno-economic positioning relative to fossil based products. In a previous paper [Broeren et al., 2016], LCA results per kg and per functionality equivalent of bio-based plastics were presented, together with economic considerations. The present paper discusses the mechanical and thermal properties of a range of commercially available bio-based plastics based on polylactic acid (PLA), cellulose esters, starch and polyamides, and the feasibility of replacing fossil-based counterparts based on performance. The evaluation is approached from an end user perspective. First, potentially suitable bio-based plastics are selected based on manufacturers' specifications in technical data sheets, then a first experimental evaluation is performed on injection moulded ISO specimens, and finally a further selection of plastics is tested on large 50×70cm panels. This technical feasibility study indicates that so far bio-based plastics do not completely match the properties of high performance materials like flame retardant V-0 PC/ABS blends used in electronic devices. The performance gap is being decreased by the development of stereocomplex PLA and hybrid PLA blends with polycarbonate, which offer clearly improved properties with respect to maximum usage temperature and toughness. In addition, several materials meet the V-0 flammability requirements needed in specific durable applications. On the other hand, improving these properties so far has negative consequences for the bio-based content. This study also shows that replacement of bulk polymers like PS is feasible using PLA compounds with a bio-based content as high as 85%. Copyright © 2016 Elsevier B.V. All rights reserved.

  18. Technical feasibility of personalized articulating knee joint distraction for treatment of tibiofemoral osteoarthritis.

    Science.gov (United States)

    Struik, T; Jaspers, J E N; Besselink, N J; van Roermund, P M; Plomp, S; Rudert, M J; Lafeber, F P J G; Mastbergen, S C

    2017-11-01

    Knee osteoarthritis is a highly prevalent degenerative joint disorder characterized by joint tissue damage and pain. Knee joint distraction has been introduced as a joint preserving surgical procedure to postpone knee arthroplasty. An often used standard externally fixation device for distraction poses a burden to patients due to the absence of joint flexion during the 6weeks treatment. Therefore, a personalized articulating distraction device was developed. The aim of this study was to test technical feasibility of this device. Based on an often applied rigid device, using equal bone pin positions and connectors, a hinge mechanism was developed consisting of a cam-following system for reproducing the complex joint-specific knee kinematics. In support, a device was developed for capturing the joint-specific sagittal plane articulation. The obtained kinematic data were translated into joint-specific cam shapes that were installed bilaterally in the hinge mechanism of the distraction device, as such providing personalized knee motion. Distraction of 5mm was performed within a range of motion of 30deg. joint flexion. Pre-clinical evaluation of the working principle was performed on human cadaveric legs and system stiffness characteristics were biomechanically evaluated. The desired range of motion was obtained and distraction was maintained under physiologically representative loading. Moreover, the joint-specific approach demonstrated tolerance of deviations from anatomical and alignment origin during initial placement of the developed distraction device. Articulation during knee distraction is considered technically feasible and has potential to decrease burden and improve acceptance of distraction therapy. Testing of clinical feasibility is warranted. Copyright © 2017 Elsevier Ltd. All rights reserved.

  19. Three-dimensional C-arm CT-guided transjugular intrahepatic portosystemic shunt placement: Feasibility, technical success and procedural time

    Energy Technology Data Exchange (ETDEWEB)

    Ketelsen, Dominik; Groezinger, Gerd; Maurer, Michael; Grosse, Ulrich; Horger, Marius; Nikolaou, Konstantin; Syha, Roland [University of Tuebingen, Department of Diagnostic and Interventional Radiology, Tuebingen (Germany); Lauer, Ulrich M. [University of Tuebingen, Internal Medicine I, Department of Gastroenterology, Hepatology and Infectious disease, Tuebingen (Germany)

    2016-12-15

    Establishment of transjugular intrahepatic portosystemic shunts (TIPS) constitutes a standard procedure in patients suffering from portal hypertension. The most difficult step in TIPS placement is blind puncture of the portal vein. This study aimed to evaluate three-dimensional mapping of portal vein branches and targeted puncture of the portal vein. Twelve consecutive patients suffering from refractory ascites by liver cirrhosis were included in this retrospective study to evaluate feasibility, technical success and procedural time of C-arm CT-targeted puncture of the portal vein. As a control, 22 patients receiving TIPS placement with fluoroscopy-guided blind puncture were included to compare procedural time. Technical success could be obtained in 100 % of the study group (targeted puncture) and in 95.5 % of the control group (blind puncture). Appropriate, three-dimensional C-arm CT-guided mapping of the portal vein branches could be achieved in all patients. The median number of punctures in the C-arm CT-guided study group was 2 ± 1.3 punctures. Procedural time was significantly lower in the study group (14.8 ± 8.2 min) compared to the control group (32.6 ± 22.7 min) (p = 0.02). C-arm CT-guided portal vein mapping is technically feasible and a promising tool for TIPS placement resulting in a significant reduction of procedural time. (orig.)

  20. Feasibility Study on Solar District Heating in China

    DEFF Research Database (Denmark)

    Huang, Junpeng; Fan, Jianhua; Furbo, Simon

    This paper analyzes the feasibility of developing solar district heating (SDH) in China from the perspective of incentive policy, selections of technical route, regional adaptability and economic feasibility for clean heating. Based on the analyzation, this proposes a road map for the development...

  1. Pre-feasibility study template for nZEB pilot projects development

    OpenAIRE

    Crespo Sánchez, Eva

    2015-01-01

    This document corresponds to Task 5.2 NZEB pilot projects development, Deliverable 5.2 Basic project conceptual design with feasibility analysis for eight pilot project of the SUSTAINCO project and should present a structure of pre-feasibility studies for eight NZEB projects implementation. It aims to give an overview of how SUSTAINCO project implementation is to be prepared and which technical and financial parameters to concern.

  2. Feasibility study of electric motors constructed with high temperature superconducting materials

    International Nuclear Information System (INIS)

    Jordan, H.E.

    1989-01-01

    The potential application of high temperature superconducting (HTSC) materials to electric motors is discussed. The specific application area of motors in electric power generating stations has been selected and a feasible study has been initiated on the use of HTSC materials in the design of motors for this application. A progress report on this feasibility study is presented. Technical challenges in both the development of HTSC wire and the design of a motor to utilize this wire are discussed. Finally, the results of design calculations comparing a superconducting motor with one of conventional design are presented assuming that success can be achieved in overcoming the technical problems which must be resolved to produce a high performance HTSC wire

  3. Nasal Unit Transplantation: A Cadaveric Anatomical Feasibility Study.

    Science.gov (United States)

    Dorafshar, Amir H; Mundinger, Gerhard S; Robinson, Brent; Tuffaha, Sami; Brandacher, Gerald; Byrne, Patrick; Walton, Robert L

    2017-05-01

    Background  The science and technical acumen in the field of vascularized composite allotransplantation has progressed rapidly over the past 15 years, and transplantation of specialized units of the face, such as the nose, appears possible. No study to date has evaluated the technical feasibility of isolated nasal unit transplantation (NUT). In this study, we explore the anatomy and technical specifics of NUT. Methods  In this study, four fresh cadaver heads were studied. Bilateral vascular pedicle dissections were performed in each cadaver. The facial artery was cannulated and injected with food dye under physiologic pressure in two cadavers, and with lead oxide mixture in two cadavers to evaluate perfusion territories supplied by each vascular pedicle. Results  The facial artery and vein were found to be adequate pedicles for NUT. Divergent courses of the vein and artery were consistently identified, which made for a bulky pedicle with necessary inclusion of large amounts of subcutaneous tissue. In all cases, the artery remained superficial, while the vein coursed in a deeper plane, and demonstrated consistent anastomoses with the superior transverse orbital arcade. While zinc oxide injection of the facial artery demonstrated filling of the nasal vasculature across the midline, dye perfusion studies suggested that unilateral arterial inflow may be insufficient to perfuse contralateral NUT components. Discrepancies in these two studies underscore the limitations of nondynamic assessment of nutritive perfusion. Conclusion  NUT based on the facial artery and facial vein is technically feasible. Angiosome evaluation suggests that bilateral pedicle anastomoses may be required to ensure optimal perfusion. Thieme Medical Publishers 333 Seventh Avenue, New York, NY 10001, USA.

  4. Technical and Feasibility Analysis of Gasoline and Natural Gas Fuelled Vehicles

    Directory of Open Access Journals (Sweden)

    Charalambos Chasos

    2014-03-01

    Full Text Available There is recent interest for the utilisation of natural gas for empowering the internal combustion engines (ICE of vehicles. The production of novel natural gas ICE for vehicles, as well as the conversion of existing gasoline fuelled ICE of vehicles to natural gas fuelled ICE are new technologies which require to be analysed and assessed. The objective of the present study is to examine the adaptation of natural gas as vehicle fuel and carry out a technical analysis and an economical feasibility analysis of the two types of ICE vehicles, namely gasoline and natural gas fuelled vehicles. The technical model uses the physical properties of the two fuels and the performance factors of internal combustion engines including brake thermal efficiency. The resulting exhaust gas emissions are also estimated by the technical model using combustion calculations which provide the expected levels of exhaust gas emissions. Based on the analysis with the technical model, comparisons of the two types of engines are performed. Furthermore, the estimated performance characteristics of the two types of engines, along with local statistical data on annual fuel imports and annual fuel consumption for transportation and data on the vehicles fleet for the case study of Cyprus are used as input in the economical model. For the base year 2013, data of natural gas price is also used in the economical model. The economical model estimates the capital cost, the carbon dioxide emissions avoidance of fines, the net present value and the internal rate of return of the investment of large scale adaptation of natural gas fuelled vehicles for the case study. From the results and comparisons, conclusions are drawn and recommendations are provided for the adaptation of natural gas vehicles which can provide improved performance with reduced pollutant emissions.

  5. Feasibility study on fission moly target development

    International Nuclear Information System (INIS)

    Kim, Byung Ku; Kim, Seong Nyun; Shon, Dong Seong; Choi, Chang Beom; Lee, Jae Kuk; Park, Jin Ho; Jeong, Won Myung; Jeon, Kwan Sik; You, Jae Hyung; Kang, Kyung Chul; Ahn, Jong Hwan; Ju, Po Kuk

    1996-01-01

    A multi-purpose research reactor, HANARO has been operated on the beginning of 1995 and can be utilized for production of various radioisotopes. And a R and D program for fission Mo production was established, and the technical and economical feasibility study has been performed for fission Mo production in Korea. In this study the process for fission Mo production was recommended as follows; 1. Target : UO 2 of annulus type. 2. Separation and purification : Nitric acid dissolution → Alumina adsorption → Benzoin oxime precipitation → Alumina adsorption. And more desirable plan for steady supply of fission Mo were suggested in following viewpoints; 1. Technical collaboration with foreign company. 2. Backup supply system. 3. Marketing arrangement. (Author)

  6. Technical feasibility of the implementing of the paper analysis in forensic documentoscopy

    International Nuclear Information System (INIS)

    Perez Alfaro, Cesar Alonso

    2013-01-01

    Technical feasibility has determined the implementation of the paper analysis in forensic documentoscopy. Methods of non-destructive and destructive testing are focused in the study. The dimensions, thickness, opacity, brightness and air permeability are analyzed by the methods of non-destructive testing. The analysis of pH, fiber, humidity and ashes are performed by destructive methods. 10 samples of paper type 'Bond' are examined of the main importers from country. The chemical and anatomy of the wood are explained. The results of the non-destructive methods have achieved to differentiate 8 of the 10 samples studied. The two remaining samples have achieved to differentiate by the fibers analysis and ashes analysis. The pH has determined in the 10 samples that the pulping method has been basic. The technical differentiation of the 'Bond' paper has been possible for use in forensic documentoscopy. The fibers present in the paper are observed applying the dye 'Graff C' and using the microscope. The dye method 'Graff C' has allowed a morphologic differentiation of the organic composition of the sample of paper [es

  7. Danish wind turbines: Technical-economic feasibility of commercial models

    International Nuclear Information System (INIS)

    Falchetta, M.

    1992-01-01

    This feasibility study examines the principal technical and economic (investment-manufacturing-installation-operation unit costs, supply and demand) characteristics of wind turbines being commercialized in Denmark. The general configuration of the 150 to 450 kW range machines currently being manufactured can be described as that of a three bladed fibreglass rotor, of from 24 to 35 meters in diameter, and mounted on a tower of from 29 to 41 meters in height. The electrical system consists of one asynchronous generator or a two generator system with a power ratio of 1 to 5 between the two generators. The cost analysis reveals that the Danish wind turbines are competitively priced, with per kWh costs varying from $0. 0675 to $0. 040 for operating wind speeds ranging from 5 to 7 m/sec, and that their overall design and performance characteristics make them suitable for Italian site conditions

  8. Nuclear Energy Center Site Survey, 1975. Part III. Technical considerations

    International Nuclear Information System (INIS)

    1976-01-01

    Studies of the technical feasibility of nuclear energy centers (NECs) and the comparison between NEC technical feasibility and that of nuclear facilities on dispersed sites are reviewed. The conclusions related to technical feasibility of NEC are summarized. Technical feasibility was found to rest mainly on five major issues: heat dissipation, transmission, facility construction, radiological impact, and environmental impact. Although general conclusions can be reached in these five areas, it is recognized that they are interdependent, and detailed site-by-site analysis will be necessary. Some general conclusions on technical feasibility of NECs are presented, then detailed conclusions derived from the technical evaluation of NECs compared to dispersed site facilities are presented. The findings of this study on each of the five major feasibility issues are then discussed in sequence. The study concludes that nuclear energy centers, as defined herein, are technically feasible

  9. Mirror power reactor magnet coil system: a technically and economically feasible design

    International Nuclear Information System (INIS)

    Peterson, M.A.

    1977-01-01

    The design and preliminary engineering analysis of a ''Yin Yang'' coil system utilizing several original design concepts to achieve technical and economic feasibility will be presented. The design analysis is begun with a general description of the constraints and prerequisites which define the problem of designing a satisfactory coil system for a mirror power reactor. This description includes a discussion of the coil conductor geometry required by plasma physics considerations, and also a description of the magnitude and direction of the magnetic force system distributed over the conductor geometry. In addition, the important design constraints which all mirror coil system designs must satisfy if they are to successfully interface with the other reactor components are reviewed. After considering the basic constraints that Yin Yong coil systems must be developed around, a survey of the various design concepts that were developed and explored in search of a satisfactory coil system design is discussed. From this extensive preliminary investigation of potential coil system configurations, a coil system design was developed which appears to offer by far the best combination of technical and economic feasibility of any other coil system design developed thus far

  10. Feasibility study on commercialization of fast breeder reactor cycle systems interim report of phase II. Technical study report for nuclear fuel cycle systems

    International Nuclear Information System (INIS)

    Sato, Koji; Amamoto, Ippei; Inoue, Akira

    2004-06-01

    As a part of the feasibility study on commercialization of fast breeder reactor cycle systems, the plant concept concerning the fuel cycle systems (combination of the reprocessing and the fuel fabrication) has been constructed to reduce their total cost by the introduction of various innovative techniques and to apply their utmost superior efficiency from such standpoints of a decrease in the environmental burden, better resource utilization and proliferation resistance improvement by the low decontamination transuranium element (TRU) recycle. This interim report of Phase II describes the results of an on-going study which will cover a five-year period. For oxide fuels, the system which combines the use of the advanced aqueous reprocessing using three main methods such as the crystallization method, the simplified solvent extraction method, and the extraction chromatography method for minor actinide (MA) recovery, as well as the simplified pelletizing fuel fabrication which rationalized a powder mixing process etc., has abundant current results and a high technical feasibility for the basic process. Though this system faces difficulties in the technical development of control technology of the extraction chromatography and the fabrication technology of low decontamination TRU fuel etc., its expected practical use is possible at an early stage. As for the super-critical direct extraction reprocessing, it is necessary to fulfill more basic data although further economical improvement of an advanced aqueous reprocessing is expected. The system which combines the advanced aqueous reprocessing and the gelation sphere packing fuel fabrication has the advantage of lesser dispersion of the fine powder due to the use of solution and granule in the fuel fabrication process. However, this system will shoulder additional cost for the reagent recovery process and the waste liquid treatment process due to need to dispose of a large bulk of process waste liquid. The system which

  11. PUEBLO OF ZIA RENEWABLE ENERGY DEVELOPMENT FEASIBILITY STUDY

    Energy Technology Data Exchange (ETDEWEB)

    Pino, Peter M. [Tribal Administrator (Ret.), Pueblo of Zia; Lakshman, Jai [Project Manager (NDA) for Pueblo of Zia; Toole, G. Loren [Principal Investigator, Los Alamos National Laboratory - Energy Analysis Team/ CCS-3, D-4; Hand, Dan [P.E., Sustainable Enginerring; Witcher, James; Emerson, Michael A. [Senior V.P., ARES Corporation; Turner, Jeremy [Executive Director, NM Renewable Energy Transmission Authority; Sandidge, Wendy [Director of Operations, NM Community Capital

    2014-06-30

    The Pueblo of Zia will conduct a comprehensive feasibility study for best-use application(s) for development of renewable energy resources on its tribally held TRUST lands (i.e., Trust Lands of Zia Indian Reservation). The feasibility study is essential for determining the technical and economic viability of a future renewable project(s) on Zia tribal lands, including the potential economic and environmental benefits for the Tribe. Project Objectives: The feasibility study is essential for determining the technical and economic viability of future renewable project(s) on Zia tribal lands, including the potential economic and environmental benefits for the Tribe to: 1. Provide a balanced local renewable power supply for Zia Pueblo, its members, tribal offices, schools and buildings, and businesses on tribal lands 2. Provide a firm power supply for export and commercial market distribution 3. Provide economic development for the Tribe and its members, including job training and creation, each in accordance with the goals and objectives as conveyed by the Pueblo of Zia Tribal Council, Tribal Administration, and outlined in The Pueblo of Zia Comprehensive Plan and Pueblo of Zia — Zia Enterprise Zone Master Plan. A key goal of the study is to analyze the integrated development of solar, geothermal, and wind renewable energy resources at Zia Pueblo, with added potential to combine gas-fired generation to accomplish energy firming. Geothermal offers a base load source of energy, providing power continuously for end users. Wind and solar offer intermediate and peaking sources of energy, which can be harvested throughout the day, with periods of variable but predicable output. Variability will be managed in an integrated manner, using Zia Pueblo's combined renewable resources to generate high-quality power. Tasks are intended to collect, catalog, map, and analyze existing data on Zia Pueblo's renewable energy resource base and then match resource attributes with

  12. Feasibility of commercial space manufacturing, production of pharmaceuticals. Volume 2: Technical analysis

    Science.gov (United States)

    1978-01-01

    A technical analysis on the feasibility of commercial manufacturing of pharmaceuticals in space is presented. The method of obtaining pharmaceutical company involvement, laboratory results of the separation of serum proteins by the continuous flow electrophoresis process, the selection and study of candidate products, and their production requirements is described. The candidate products are antihemophilic factor, beta cells, erythropoietin, epidermal growth factor, alpha-1-antitrypsin and interferon. Production mass balances for antihemophelic factor, beta cells, and erythropoietin were compared for space versus ground operation. A conceptual description of a multiproduct processing system for space operation is discussed. Production requirements for epidermal growth factor of alpha-1-antitrypsin and interferon are presented.

  13. Feasibility study on intersection in North Sumatera

    Science.gov (United States)

    Hastuty, I. P.; Sembiring, I. S.; Anas, R.; Lubis, A. S.

    2018-02-01

    Traffic congestion is one of the problems faced by big cities, One of them is Binjai city and Medan city in North Sumatera. One of the causes of congestion is intersection of roads with highway and roads with railroads. To ensure the smooth movement of vehicles, technical handling at the intersection is needed. Therefore, it is necessary to pre-study the feasibility of level crossing in Binjai and Medan to be able to assess the investment needs and the level of importance of road development in the region. The development of transportation infrastructure and facilities is based on the thought of improving the transportation network system. The necessity of systemical integrated transportation system handling is needed in creating a transportation efficiency. The purpose of this study is to identify and prioritize the needs of the railway crossings. The objective which we want to be achieved is to obtain a document that contains technical, economic and environmental ability indicators as a reference in the feasibility and planning studies. The methodology used is collecting the primary data, secondary data, introduction of study area as the initial analysis of the problem. From the study it can be concluded that the existence of railway interchange will move the movement through traffic so it will not interfere the movement of traffic within urban areas and it keeps the national road network performance is still good.

  14. Technical Survey and Feasibility Review for Development of IV-CEAPI

    International Nuclear Information System (INIS)

    Jang, Yongtae; Park, Jinseok; Lee, Myounggoo; Cho, Yeonho; Kim, Hyunmin

    2016-01-01

    The purpose of this paper is to establish the development direction of the IV-CEAPI(Control element assembly position indicator). The paper presents the technologies of the existing CEAPI and other linear displacement sensors. The paper also presents feasibility review of those technologies for the IV-CEAPI considering its environmental conditions as shown in Table 1. an instrument to monitor vertical position of the control element assembly (CEA) in nuclear reactors. The CEAPI is installed in each control element drive mechanism (CEDM). The conventional CEDMs are installed outside the reactor vessel (RV) with nozzles penetrating the RV head. To select the type of the IV-CEAPI, technical surveys on linear displacement sensors were performed. Feasibility of those sensors was reviewed considering the environment conditions, experience, reliability and simplicity. The result is summarized in Table 2 which implies that the solenoid type is considered to be the best suitable types for the IV-CEAPI

  15. Gasohol: economic feasibility study. Final report

    Energy Technology Data Exchange (ETDEWEB)

    David, M. L.; Hammaker, G. S.; Buzenberg, R. J.; Wagner, J. P.

    1978-07-01

    This report was prepared by Development Planning and Research Associates, Inc. under a contract with the Energy Research and Development Center of the University of Nebraska in cooperation with the Agricultural Products Industrial Utilization Committee and the State of Nebraska. Funding for this study was provided to the Energy Research and Development Center by the U.S. Department of Energy and the Old West Regional Commission. The primary objective of the study was to: determine the fiscal and market conditions under which the production of gasohol would be profitable for private producers. For purposes of this study, gasohol is a motor fuel consisting of 10 percent agriculturally-derived anhydrous ethanol and 90 percent unleaded gasoline. The study assumes that gasohol can be a fuel substitute for gasoline; indeed, the cost of gasoline will significantly influence that for gasohol. Gasoline prices are determined by factors external to ethanol; thus, the economic feasibility study of gasohol is in large part an economic feasibility study of fuel-grade ethanol production. More specifically, the study examined the following: the technical aspects of distributing, marketing, and using gasohol; the costs of the distribution and marketing of ethanol and gasohol; the energy balance of ethanol production; the cost of producing ethanol; the factors influencing ehtanol plant size and location; and the conditions that would make ethanol economicaly feasible for private producers.

  16. Cogeneration feasibility study in the Gulf States Utilities service area

    Energy Technology Data Exchange (ETDEWEB)

    1979-12-01

    Sites in the Gulf States Utilities service are considered for cogeneration feasibility studies. The sources of steam considered for the Orange, Texas and Geismar, Lake Charles, and North Baton Rouge, Louisiana sites include oil, coal, HTGR steamers, consolidated nuclear steam system, atmospheric fluidized-bed coal combustion, and coal gasification. Concepts concerning cogeneration fuel systems were categorized by technical applicability as: current technology (pulverized coal-fired boilers and fuel oil-fired boilers), advanced technology under development (HTGR steamers and the CNSS), and advanced technology for future development (atmospheric fluidized-bed boilers and coal gasification). In addition to providing data on cogeneration plant generally useful in the US, the study determined the technical and economic feasibility of steam and electric power cogeneration using coal and nuclear fuels for localized industrial complexes. Details on site selection, plant descriptions, cost estimates, economic analysis, and plant schedule and implementation. (MCW)

  17. Hydrogen production by supercritical water gasification of biomass. Phase 1 -- Technical and business feasibility study, technical progress report

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-12-01

    The nine-month Phase 1 feasibility study was directed toward the application of supercritical water gasification (SCWG) for the economical production and end use of hydrogen from renewable energy sources such as sewage sludge, pulp waste, agricultural wastes, and ultimately the combustible portion of municipal solid waste. Unique in comparison to other gasifier systems, the properties of supercritical water (SCW) are ideal for processing biowastes with high moisture content or contain toxic or hazardous contaminants. During Phase I, an end-to-end SCWG system was evaluated. A range of process options was initially considered for each of the key subsystems. This was followed by tests of sewage sludge feed preparation, pumping and gasification in the SCW pilot plant facility. Based on the initial process review and successful pilot-scale testing, engineering evaluations were performed that defined a baseline system for the production, storage and end use of hydrogen. The results compare favorably with alternative biomass gasifiers currently being developed. The results were then discussed with regional wastewater treatment facility operators to gain their perspective on the proposed commercial SCWG systems and to help define the potential market. Finally, the technical and business plans were developed based on perceived market needs and the projected capital and operating costs of SCWG units. The result is a three-year plan for further development, culminating in a follow-on demonstration test of a 5 MT/day system at a local wastewater treatment plant.

  18. Evaluation of the feasibility, economic impact, and effectiveness of underground nuclear power plants. Final technical report

    International Nuclear Information System (INIS)

    1978-05-01

    Information on underground nuclear power plants is presented concerning underground nuclear power plant concepts; public health impacts; technical feasibility of underground concepts; economic impacts of underground construction; and evaluation of related issues

  19. Technical feasibility study for the D-T neutron monitor using activation of the flowing water

    International Nuclear Information System (INIS)

    Uno, Yoshitomo; Kaneko, Junichi; Nishitani, Takeo; Maekawa, Fujio; Tanaka, Teruya; Ikeda, Yujiro; Takeuchi, Hiroshi

    2001-03-01

    The experimental study of technical feasibility for the D-T neutron monitor using activation of the flowing water was performed at FNS/JAERI as the ITER/EDA R and D Task T499. The temporal resolution for pulsed neutrons was measured and dependence of the temporal resolution on flowing velocity was studied. The temporal resolution of 50 ms that is better than 100 ms of the requirement for ITER was achieved. We found that the temporal resolution is determined by a turbulent dispersion of the flow. The experiment for validation of the method determining the absolute D-T neutron flux was carried out by using the stainless steel (SS 316)/Water assembly to simulate the neutron field in the blanket region of ITER. The neutron emission rate measured with the water activation has a good agreement with that with the neutron yield monitor with associated α detector, and this technique shows the accuracy of the absolute neutron flux better than 10%. At the application on ITER-FEAT, the neutron activation with fluid flow has a dynamic range of 50 kW - 500 MW operation with a temporal resolution of 78 ms at the flow velocity of 10 m/s. (author)

  20. Feasibility study for mega-electron-volt electron beam tomography.

    Science.gov (United States)

    Hampel, U; Bärtling, Y; Hoppe, D; Kuksanov, N; Fadeev, S; Salimov, R

    2012-09-01

    Electron beam tomography is a promising imaging modality for the study of fast technical processes. But for many technical objects of interest x rays of several hundreds of keV energy are required to achieve sufficient material penetration. In this article we report on a feasibility study for fast electron beam computed tomography with a 1 MeV electron beam. The experimental setup comprises an electrostatic accelerator with beam optics, transmission target, and a single x-ray detector. We employed an inverse fan-beam tomography approach with radiographic projections being generated from the linearly moving x-ray source. Angular projections were obtained by rotating the object.

  1. Feasibility studies for decommissioning

    International Nuclear Information System (INIS)

    Hladky, E.

    2000-01-01

    In this presentation author deals with planning of decommission of the NPPs A1, V1 and V2 Bohunice and Mochovce. It was concluded that: Used model for decommissioning parameters assessment has been suitable for elaboration of initial decommissioning plans (feasibility studies); Basic assessment of main decommissioning parameters and basic comparison of various decommissioning options have been possible; Improvement of the model and corresponding software is desirable and works on software improvement began one year ago; V1-NPP initial decommissioning plan should be actualized, because initial decommissioning plan does not correspond by its content and structure to requirements of Act No. 130/98 and Nuclear Regulatory Authority Degree No. 246/99; Strategy of radioactive wastes treatment and conditioning together with technical provisions at Jaslovske Bohunice site was changed in comparison with the assumptions in 1991-92; Considered V1 NPP decommissioning options are necessary to be re-evaluated in accordance with latest development of knowledge and approaches to NPP decommissioning in the world; Specific unit costs are substantially and differentially changed in comparison with the assumptions in 1991-92; Necessity to take into account technical changes resulted from V1 NPP reconstruction. (author)

  2. Technical and economical feasibility studies and preliminary plan of a heavy water plant by the criogenic distillation method of hydrogen

    International Nuclear Information System (INIS)

    Dias Vargas, F.

    1983-01-01

    This paper presents the pre-feasibility study of a heavy water production plant, both from the technical and economical point of view. Criogenic distillation of hydrogen is used as the final enrichment stage. The deuterium source is water treated previously by a process of enrichment based on the water-hydrogen isotopic exchange. The economical analysis is aimed at the study of the feasibility of the installation of a heavy water moderated reaction in Chile. General properties of heavy water are presented and also the various materials of its enrichment at the industrial scale. The plant itself has a first stage based on the water-hydrogen isotopic exchange procesS, where deuterium is extracted from the water by the hydrogen which is subsequently treated in a criogenic distillation stage. An important fact of the plant analysis is the calculation of heat exchangers mainly in relation to the problem posed by tHe hydrogen's low point of liquifaction. The distillation units are also treated and designed. The economic evaluation produces project diScount rates of 15.71% and 21.97%, for 25 tons/year and 40 tons/year of production capacity. The heavy water price used for these evaluation was 600 $/Kg

  3. Technical feasibility for electron beam application on maize seeds disinfection for maize cultivation in Brazil

    International Nuclear Information System (INIS)

    Zago, Claudia; Rela, Paulo Roberto

    2007-01-01

    Among the man made activities agriculture plays a fundamental rule on the interference with environment; new alternatives for clean technologies are being searched in order to reduce the impact and degradation of the environment. This work presents a feasibility study to implement in Brazil a technology using electron beam treatment to disinfect maize seeds avoiding the spoilage from pathogens microorganisms. This technology was developed in Germany by Fraunhofer Institut FEP (Dresden) and the private company Schmidt-Seeger AG. It was patented as 'e-ventus'. Concerning to the technical feasibility it shows to be quite useful due to the results of the experiments performed in other countries with maize seeds and properly for the large amount to be treated in the country. Under the environmental management it is quite advantageous when compared with the traditional technology that uses chemical seed dressing agents. Nevertheless for a large scale commercial application it is necessary a cost analyse comparison study between the traditional technology and the alternative using electron beam. (author)

  4. Pyrolysis in Groningen, Netherlands. Feasibility study on a transition coalition

    International Nuclear Information System (INIS)

    Siemons, R.V.

    2005-01-01

    Results of a study on the technical, economical and financial feasibility of a pyrolysis factory for the processing and energetic application of biomass wastes in the Dutch province Groningen are presented and discussed. Also, attention is paid to the implementation of the planned pyrolysis factory in one or more transition programmes. [nl

  5. Investigation/evaluation of water cooled fast reactor in the feasibility study on commercialized fast reactor cycle systems. Intermediate evaluation of phase-II study

    International Nuclear Information System (INIS)

    Kotake, Syoji; Nishikawa, Akira

    2005-01-01

    Feasibility study on commercialized fast reactor cycle systems aims at investigation and evaluation of FBR design requirement's attainability, operation and maintenance, and technical feasibility of the candidate system. Development targets are 1) ensuring safety, 2) economic competitiveness, 3) efficient utilization of resources, 4) reduction of environmental load and 5) enhancement of nuclear non-proliferation. Based on the selection of the promising concepts in the first phase, conceptual design for the plant system has proceeded with the following plant system: a) sodium cooled reactors at large size and medium size module reactors, b) a lead-bismuth cooled medium size reactor, c) a helium gas cooled large size reactor and d) a BWR type large size FBR. Technical development and feasibility has been assessed and the study considers the need of respective key technology development for the confirmation of the feasibility study. (T. Tanaka)

  6. Depleted uranium concrete container feasibility study

    International Nuclear Information System (INIS)

    Haelsig, R.T.

    1994-09-01

    The purpose of this report is to consider the feasibility of using containers constructed of depleted uranium aggregate concrete (DUCRETE) to store and transport radioactive materials. The method for this study was to review the advantages and disadvantages of DUCRETE containers considering design requirements for potential applications. The author found that DUCRETE is a promising material for onsite storage containers, provided DUCRETE vessels can be certified for one-way transport to disposal sites. The author also found that DUCRETE multipurpose spent nuclear fuel storage/transport packages are technically viable, provided altered temperature acceptance limits can be developed for DUCRETE

  7. Technical and economic feasibility of thermal energy storage. Thermal energy storage application to the brick/ceramic industry. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Glenn, D.R.

    1976-10-01

    An initial project to study the technical and economic feasibility of thermal energy storage (TES) in the three major consumer markets, namely, the residential, commercial and industrial sectors is described. A major objective of the study was to identify viable TES applications from which a more concise study could be launched, leading to a conceptual design and in-depth validation of the TES energy impacts. This report documents one such program. The brick/ceramic industries commonly use periodic kilns which by their operating cycle require time-variant energy supply and consequently variable heat rejection. This application was one of the numerous TES opportunities that emerged from the first study, now available from the ERDA Technical Information Center, Oak Ridge, Tennessee, identified as Report No. COO-2558-1.

  8. Canton hydroelectric project: feasibility study. Final report, appendices

    Energy Technology Data Exchange (ETDEWEB)

    1979-05-01

    These appendices contain legal, environmental, regulatory, technical and economic information used in evaluating the feasibility of redeveloping the hydroelectric power generating facilities at the Upper and Lower Dams of the Farmington River at Collinsville, CT. (LCL)

  9. Study of technical and financial pre-feasibility to produce a natural shampoo and ecological

    International Nuclear Information System (INIS)

    Arauz Villegas, Tatiana

    2014-01-01

    A study of technical and financial pre-feasibility was described for producing natural shampoo, ecological and to determine attributes desired by people in that shampoo. A survey was performed to study which characteristics have improved the hair condition; and from the results a model was developed with which is backing the formulation of the shampoo. The proposed shampoo has had as functionality provide hair shine, moisturize, reconstruct, provide protection and has reduced the static (is anti-frizz) because has used biodegradable and friendly raw materials to the environment. The color is light green and its aroma-herbal will have a white container with green lid and will be marketed in 500mL presentation. The production process is done in six steps: reception, storage and dosing of raw materials, preparation of the surfactant and liquid phase of shampoo (addition of active natural preservatives, dyes and fragrances), preparation of the stabilizing phase, mixed, pH regulation and quality control, packaging and storage. A semi-continuous production system was suggested to be more economical, flexible and easy to sterilize. The equipments used in the process are: a stirred tank of 205L, a stirred tank of 500L and a Semiautomatic packaging each built in stainless steel with sanitary finish by the company TECNOFAR. The tanks were designed in compliance with the typical dimensions of these teams and were sized in order to supply the first 5 years of production. A publicity campaign and marketing is recommended to fulfill sales target and execute the project of a plant to produce shampoo and natural cosmetics [es

  10. Moroccan wind farm potential feasibility. Case study

    International Nuclear Information System (INIS)

    Nouri, Abdellatif; Ait Babram, Mohamed; Elwarraki, Elmostafa; Enzili, Mustapha

    2016-01-01

    Highlights: • A new methodology for the technical feasibility of wind farm potentials is proposed. • The wind resources of two different sites in Morocco are compared. • Comparison between short and long term data using multivariate analysis is made. • Geographic information system implementation. • A 10 MW wind farm is designed and optimized. - Abstract: The subject of this paper is the elaboration of a methodology to study the technical feasibility of a wind farm potential. The implementation of this methodology allows a comparison between the wind resources of two different sites in Morocco. One site is located in the region of Essaouira, whereas the other one is located in the region of Safi. The comparison is based on real wind data collected from two masts at the heights of 30, 50, and 60 m. Each of the masts is installed at one of the mentioned potential sites over a fixed time period, lasting fifteen months for the first site, and eight months for the second one. The aim is the determination of the most applicable site presenting a good potential for a statistical study in order to predict long-term wind behaviors. Thus, the geographical situation study of the chosen site including topography, roughness and obstacles, is carried out. Furthermore, the wind resource using data, generated by the measuring masts, is evaluated. Finally, the areas which present great wind potential are located and the wind farm turbine locations are optimized by using the WAsP software.

  11. Technical feasibility of retrieval within the UK repository concept for ILW/LLW

    International Nuclear Information System (INIS)

    McCall, A.; McKirdy, B.

    2000-01-01

    Nirex is developing a staged, reversible concept for the disposal of ILW and certain LLW in the UK. Within that concept, the retrievability strategy includes the option of keeping open the repository, for an extended period, after all waste has been emplaced. In examining the feasibility of such an approach, a number of key technical issues have been identified and options for addressing these issues have been established. This paper will describe the issues identified and the development of practical solutions for incorporating retrievability within the Nirex concept. (author)

  12. Vertebral split fractures: Technical feasibility of percutaneous vertebroplasty

    Energy Technology Data Exchange (ETDEWEB)

    Huwart, Laurent, E-mail: huwart.laurent@wanadoo.fr [Department of Radiology, Hôpital Archet 2, Centre Hospitalo-Universitaire de Nice, Nice (France); Foti, Pauline, E-mail: pfoti@hotmail.fr [Department of Biostatistics, Hôpital Archet 2, Centre Hospitalo-Universitaire de Nice, Nice (France); Andreani, Olivier, E-mail: andreani.olivier@gmail.com [Department of Radiology, Hôpital Archet 2, Centre Hospitalo-Universitaire de Nice, Nice (France); Hauger, Olivier, E-mail: olivier.hauger@chubordeaux.fr [Department of Radiology, Hôpital Pellegrin, Centre Hospitalo-Universitaire de Bordeaux, Bordeaux (France); Cervantes, Elodie, E-mail: elodie.cervantes@live.fr [Department of Radiology, Hôpital Archet 2, Centre Hospitalo-Universitaire de Nice, Nice (France); Brunner, Philippe, E-mail: pbrunner@chpg.mc [Department of Radiology, Hôpital Princesse Grasse de Monaco (Monaco); Boileau, Pascal, E-mail: boileau.p@chu-nice.fr [Department of Orthopedic Surgery, Hôpital Archet 2, Centre Hospitalo-Universitaire de Nice, Nice (France); Amoretti, Nicolas, E-mail: amorettinicolas@yahoo.fr [Department of Radiology, Hôpital Archet 2, Centre Hospitalo-Universitaire de Nice, Nice (France)

    2014-01-15

    Objective: The treatment of vertebral split fractures remains controversial, consisting of either corset or internal fixation. The aim of this study was to evaluate the technical feasibility of CT- and fluoroscopy-guided percutaneous vertebroplasty in the treatment of vertebral split fractures. Materials and methods: Institutional review board approval and informed consent were obtained for this study. Sixty-two consecutive adult patients who had post-traumatic vertebral split fractures (A2 according to the AO classification) without neurological symptoms were prospectively treated by percutaneous vertebroplasty. All these procedures were performed by an interventional radiologist under computed tomography (CT) and fluoroscopy guidance by using only local anaesthesia. Postoperative outcome was assessed using the visual analogue scale (VAS) and Oswestry disability index (ODI) scores. Results: Vertebroplasty was performed on thoracic and lumbar vertebrae, creating a cement bridge between the displaced fragment and the rest of the vertebral body. Seven discal cement leakages (11%) were observed, without occurrence of adjacent vertebral compression fractures. The mean VAS measurements ± standard deviation (SD) significantly decreased from 7.9 ± 1.5 preoperatively to 3.3 ± 2.1 at 1 day, 2.2 ± 2.0 at 1 month, and 1.8 ± 1.4 at 6 months (P < 0.001). The mean ODI scores ± SD had also a significant improvement: 62.3 ± 17.2 preoperatively and 15.1 ± 6.0 at the 6-month follow-up (P < 0.001). Conclusion: This study suggests that type A2 vertebral fractures could be successfully treated by CT- and fluoroscopy-guided percutaneous vertebroplasty.

  13. Vertebral split fractures: Technical feasibility of percutaneous vertebroplasty

    International Nuclear Information System (INIS)

    Huwart, Laurent; Foti, Pauline; Andreani, Olivier; Hauger, Olivier; Cervantes, Elodie; Brunner, Philippe; Boileau, Pascal; Amoretti, Nicolas

    2014-01-01

    Objective: The treatment of vertebral split fractures remains controversial, consisting of either corset or internal fixation. The aim of this study was to evaluate the technical feasibility of CT- and fluoroscopy-guided percutaneous vertebroplasty in the treatment of vertebral split fractures. Materials and methods: Institutional review board approval and informed consent were obtained for this study. Sixty-two consecutive adult patients who had post-traumatic vertebral split fractures (A2 according to the AO classification) without neurological symptoms were prospectively treated by percutaneous vertebroplasty. All these procedures were performed by an interventional radiologist under computed tomography (CT) and fluoroscopy guidance by using only local anaesthesia. Postoperative outcome was assessed using the visual analogue scale (VAS) and Oswestry disability index (ODI) scores. Results: Vertebroplasty was performed on thoracic and lumbar vertebrae, creating a cement bridge between the displaced fragment and the rest of the vertebral body. Seven discal cement leakages (11%) were observed, without occurrence of adjacent vertebral compression fractures. The mean VAS measurements ± standard deviation (SD) significantly decreased from 7.9 ± 1.5 preoperatively to 3.3 ± 2.1 at 1 day, 2.2 ± 2.0 at 1 month, and 1.8 ± 1.4 at 6 months (P < 0.001). The mean ODI scores ± SD had also a significant improvement: 62.3 ± 17.2 preoperatively and 15.1 ± 6.0 at the 6-month follow-up (P < 0.001). Conclusion: This study suggests that type A2 vertebral fractures could be successfully treated by CT- and fluoroscopy-guided percutaneous vertebroplasty

  14. Technical feasibility for electron beam application on maize seeds disinfection for maize cultivation in Brazil

    Energy Technology Data Exchange (ETDEWEB)

    Zago, Claudia [Proenco Brasil Ltda. (Brazil)]. E-mail: clauzago@uol.com.br; Rela, Paulo Roberto [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (brazil). Centro de Tecnologia das Radiacoes]. E-mail: prela@ipen.br

    2007-07-01

    Among the man made activities agriculture plays a fundamental rule on the interference with environment; new alternatives for clean technologies are being searched in order to reduce the impact and degradation of the environment. This work presents a feasibility study to implement in Brazil a technology using electron beam treatment to disinfect maize seeds avoiding the spoilage from pathogens microorganisms. This technology was developed in Germany by Fraunhofer Institut FEP (Dresden) and the private company Schmidt-Seeger AG. It was patented as 'e-ventus'. Concerning to the technical feasibility it shows to be quite useful due to the results of the experiments performed in other countries with maize seeds and properly for the large amount to be treated in the country. Under the environmental management it is quite advantageous when compared with the traditional technology that uses chemical seed dressing agents. Nevertheless for a large scale commercial application it is necessary a cost analyse comparison study between the traditional technology and the alternative using electron beam. (author)

  15. Economic Feasibility Study for Using Irradiation Technology in Preservation of Animalism Foods

    International Nuclear Information System (INIS)

    El Gameel, E.A.

    2011-01-01

    The present study discus the economic feasibility for the preservation animalism foods by using irradiation technology. This study has included the technical data, regression foretelling for the throughput, determination of irradiators types and radiation sources activity. This study comprises the financial analysis for the establishment animalism foods irradiation facilities (types: tote box, pallet conveyor) and the national return

  16. Feasibility studies on cogeneration from industrial wood-processing residues in Ghana

    International Nuclear Information System (INIS)

    Brew-Hammond, A.; Atakora, S.B.

    1999-01-01

    Several feasibility studies have been undertaken on cogeneration from wood-processing industrial residues in Ghana; practically all concluded that it was not economically viable because of the low tariffs for electricity in Ghana (around 3.5 US cents per kWh) at the time. Tariffs have more than doubled since September 1998 and average tariffs for industrial consumers are now around 7-8 US cents/kWh. This paper reviews earlier studies and undertakes a sensitivity analysis to determine effects of the new tariff regime and the investment costs for co-generation projects. More detailed technical and economic feasibility studies are needed to prepare the ground for an investment programme in cogeneration from wood residues. (author)

  17. Feasibility study for private-sector treatment services for alpha-contaminated low-level mixed wastes

    International Nuclear Information System (INIS)

    Bloom, R.R.; Rodriguez, R.R.

    1995-01-01

    Rust Federal Services, under contract to the United States Department of Energy (DOE), Idaho Operations Office, performed a study to develop and evaluate the feasibility of a suggested private sector solution for the treatment of alpha-contaminated low-level mixed waste (ALLMW) stored or produced at the Idaho National Engineering Laboratory (INEL). The feasibility study is an initial step in the potential procurement of privatized treatment services for these wastes. Rust's derived objective of the feasibility study was to define an optimal treatment system and analyze the feasibility of that system for accomplishing the processing objectives specified by DOE. All aspects of the selected treatment system were addressed in the feasibility study, including technical, regulatory, public involvement, and financial considerations. Two central elements of the study were a technology screening task to select the optimal treatment system and an analysis of the institutional, business, financial, and contractual issues that are likely to accompany the privatization of treatment services for DOE

  18. Renewable energies in transition: from their social acceptability to their socio-technical feasibility

    International Nuclear Information System (INIS)

    Zelem, M.C.

    2012-01-01

    The increasing recourse to renewable energies presents an opportunity to guarantee the smooth passage from an energy guzzling and carbon emitting system to one with more reasonable characteristics, allowing our societal structures to aspire for longer durability. This process entails putting aside the notion of social acceptability, which tends to place the weight of responsibility for our energy devouring life styles on consumers, replacing it by the notion of socio-technical feasibility which forces questioning the meaning of technology and political choices in energy matters. (author)

  19. Updated (BP3) Technical and Economic Feasibility Study - Electrochemical Membrane for Carbon Dioxide Capture and Power Generation

    Energy Technology Data Exchange (ETDEWEB)

    Ghezel-Ayagh, Hossein

    2016-10-12

    This topical report summarizes the results of an updated Technical & Economic Feasibility Study (T&EFS) which was conducted in Budget Period 3 of the project to evaluate the performance and cost of the Electrochemical Membrane (ECM)-based CO2 capture system. The ECM technology is derived from commercially available inorganic membranes; the same used in FuelCell Energy’s commercial fuel cell power plants and sold under the trade name Direct FuelCell® (DFC®). The ECM stacks are utilized in the Combined Electric Power (generation) And Carbon dioxide Separation (CEPACS) systems which can be deployed as add-ons to conventional power plants (Pulverized Coal, Combined Cycle, etc.) or industrial facilities to simultaneously produce power while capturing >90% of the CO2 from the flue gas. In this study, an ECM-based CEPACS plant was designed to capture and compress >90% of the CO2 (for sequestration or beneficial use) from the flue gas of a reference 550 MW (nominal, net AC) Pulverized Coal (PC) Rankine Cycle (Subcritical steam) power plant. ECM performance was updated based on bench scale ECM stack test results. The system process simulations were performed to generate the CEPACS plant performance estimates. The performance assessment included estimation of the parasitic power consumption for CO2 capture and compression, and the efficiency impact on the PC plant. While the ECM-based CEPACS system for the 550 MW PC plant captures 90% of CO2 from the flue gas, it generates additional (net AC) power after compensating for the auxiliary power requirements of CO2 capture and compression. An equipment list, ECM stacks packaging design, and CEPACS plant layout were developed to facilitate the economic analysis. Vendor quotes were also solicited. The economic feasibility study included estimation of CEPACS plant capital cost, cost of electricity (COE) analyses and estimation of cost per ton of CO2 captured. The incremental COE for the ECM-based CO2 capture is expected to meet

  20. Study on feasible technical potential of coal to electricity in china

    Science.gov (United States)

    Jia, Dexiang; Tan, Xiandong

    2017-01-01

    The control of bulk coal is one of the important work of air pollution control in China’s future. Existing research mainly focuses on the adaptability, economy, construction and renovation plan, and operation optimization of specific energy substitution utilization, and lacks the strategy research of long-term layout of energy substitution utilization in large area. This paper puts forward a technical potential prediction method of coal to electricity based on the thermal equivalent method, which is based on the characteristics of regional coal consumption, and combined with the trend of adaptability and economy of energy substitution utilization. Also, the paper calculates the comprehensive benefit of coal to electricity according to the varieties of energy consumption and pollutant emission level of unit energy consumption in China’s future. The research result shows that the development technical potential of coal to electricity in China is huge, about 1.8 trillion kWh, including distributed electric heating, heat pump and electric heating boiler, mainly located in North China, East China, and Northeast China. The implementation of coal to electricity has remarkable comprehensive benefits in energy conservation and emission reduction, and improvement of energy consumption safety level. Case study shows the rationality of the proposed method.

  1. Technical and economic feasibility of distributed generation of electricity; Viabilidade tecnica e economica de geracao distribuida de energia eletrica

    Energy Technology Data Exchange (ETDEWEB)

    Rabelo, Frederico Augusto Ornelas; Espirito Santo, Marcos Vinicius do; Leite, Leonardo Henrique de Melo; Silva, Arlete Vieira da [Centro Universitario de Belo Horizonte (UnBH), MG (Brazil)], e-mails: fred.aor@hotmail.com, marcos_ves@yahoo.com.br, leonardo.leite@prof.unibh.br, arlete.silva@prof.unibh.br

    2011-07-01

    This article focuses on the technical and economic feasibility of the design and implementation of energy micro nets distributed generation (GD). For this, a study was conducted in a rural area to assess the potential of generating electricity from renewable sources, and this has assisted the Brazilian network of conventional energy. We studied the renewable energy village, considered the conventional system of generation, transmission, distribution of electricity in this region and the technical and economic feasibility of implementing distributed generation and its interconnection to the basic network or not. The methodological procedures were used bibliographic and documentary research, interviews with standardized forms, and Case Study. This study was conducted in Minas Gerais assessing the current conditions of the electrification of the area surveyed and deployment of the types of electricity sources - biomass (biogas and burning eucalyptus), wind, solar photovoltaic. The calculations were made from it with companies and budgets. It is conceived, then, models of generating electricity through renewable sources constitutes a GD. Finally, they estimated the costs of implementation of the models studied in the community where they were cost estimates for electric power production through private investment, considering some possible scenarios to be created, namely: generation for own consumption, generation the sale of surplus and possible expansions. In this way demonstrated the high value of the investments required for the use of renewable sources in electricity generation small, given the current scenario. (author)

  2. Pascua Yaqui Tribe Renewable Energy Development and Deployment Feasibility Study

    Energy Technology Data Exchange (ETDEWEB)

    Arvayo, Maria

    2014-05-30

    In 2012, PYT was awarded a grant from the Department of Energy Tribal Energy Program to conduct a Renewable Energy Development and Deployment Feasibility Study that would define the technical and economic viability of renewable energy on tribal lands. Red Mountain Energy Partners (RMEP) was hired by PYT to complete the study. Through this study, Red Mountain concluded that there are viable opportunities for solar at Tortuga Ranch, the Casino del Sol and a third site near the Justice Center on Camino de Oeste.

  3. A Feasibility study of a mining business

    Directory of Open Access Journals (Sweden)

    Cehlár Michal

    2001-06-01

    Full Text Available The economic evaluation of a project requires a great deal of diverse information to be brought together in one place. The greatest concern is that there will be an error by omission, so it is useful to have a detailed list of what one needs to know in order to make a thorough evaluation.There are various of detail required at the different stages of evaluation in the project, from the "quick and dirty" overview to the pre-feasibility study, through a full detailed feasibility study, to a due diligence review. This list addresses most of the economic variables in project and can be used at all levels of studies. Its purpose is to identify a variable or issue and to raise a question, which the review can pursue in more detail using an increasingly more comprehensive checklist for each topic. While developed from the point of view of a new project, this list is equally valid for an ongoing operation.A feasibility study is defined as an assessment of all aspects of a project including technical, infrastructural, environmental, social, legislative and commercial factors, which is sufficiently detailed to support a decision on the implementation. Each project has an associated level of risk. For a proposed investment to increase the value of a firm's stock, it should have a higher expected rate of return than shareholders require for assuming that risk. Since investors demand for a higher potential returns from a riskier project, the cost of capital depends on the venture's risk.

  4. Technical study report on reprocessing systems. The report of the feasibility study on commercialized FR cycle systems (phase I)

    International Nuclear Information System (INIS)

    Tanaka, Hiroshi; Kawamura, Fumio; Kakehi, Isao

    2001-04-01

    As a part of the feasibility study (FS) on commercialized fast reactor (FR) cycle systems started on July 1999, the design studies and the technical assessments for various advanced reprocessing systems have been carried out. In this study, plant design for the advanced aqueous system and the three non-aqueous systems (oxide electrowinning method, metal electrorefining method, and fluoride volatility method) has been carried out, and each system has been evaluated mainly from the viewpoint of economics. The future R and D issues on the processes and systems have been also clarified. This report describes the results of the study for two years as final report of FS phase I. (1) The advanced aqueous system, based on the simplified PUREX process, has been shown to be much more economical than the conventional PUREX. The 200 tHM/y plant achieves the target of economics, but the 50 tHM/y plant can not achieve the target. (2) The promising alternative systems replaced for advanced aqueous are the supercritical fluid direct extraction method and amine extraction method from the economical viewpoint. The ion exchange method is promising as the process for minor actinide recovery. (3) For reprocessing MOX fuel, all non-aqueous plants with a capacity of 200 tHM/y achieve the economical target. For such a small capacity as 50 tHM/y, further rationalization of the process is required for the oxide electrowinning method and metal electrorefining method to attain the target, though they are more economical than the advanced aqueous system. (4) For metallic and nitride fuel reprocessing, a metal electrorefining system has been shown to be advantageous. (author)

  5. Study of technical and economical feasibility for implementation of a movable unit for treatment of industrial effluents with electron beam

    International Nuclear Information System (INIS)

    Rela, Carolina Sciamarelli

    2006-01-01

    The treatment of industrial effluents is a practice that is disseminating in accelerated rhythm, of contributing to reinforce the public image, through the combat of the pollution, it brings economical advantages allowing the companies the reuse of the treated water in their own processes. The liquid effluent treatment technique studied in the present work is the one that uses the chemical oxidation/reduction standing out the use of the electron beam (e.b.) radiation. This technique uses an advanced oxidation process, generating radicals highly reagents that provoke the oxidation, reduction, dissociation and degradation in composed organic and exercising lethal effect in general in the microorganisms and parasites. In this work a conceptual and basic project of a movable unit of effluents treatment using electron beam radiation process was developed, in order that the unit moves until the treatment point, where the effluent is produced, facilitating the logistics. A technical and economical feasibility study was also elaborated allowing data on the capacity and cost of effluents processing to consolidate the values of the necessary investments to be presented to foundations organs for the construction of a movable unit. The results of the studies demonstrated that it is technically viable attending the pertinent legislation of Brazil, in the aspects of Radiation Protection and transport limit capacity. The unitary cost of the e.b. radiation processing in the movable unit was shown more expensive than in the fixed unit, the reason is the decrease of the efficiency of the interaction of the incident electrons in the effluent, due to the reduction of electron energy operation time of the unit. (author)

  6. Current status of feasibility studies on commercialized fuel cycle system for Fast Breeder Reactor

    International Nuclear Information System (INIS)

    Ojima, Hisao; Nagaoki, Yoshihiro

    2000-01-01

    A 'Feasibility Studies on Commercialized Fast Breeder Reactor Cycle System' is underway at the Japan Nuclear Cycle Development Institute (JNC). The study will select the promising concepts with their R and D tasks in order to commercialize the fast breeder reactor (FBR) cycle system. The feasibility studies (F/S) have to present surveyed and screened various relevant technologies, and defined the design requirement of the commercialized fuel cycle system for FBR. The promising technical options are being evaluated and conceptual designs are being examined. At the end of JFY2000, several candidate concepts of the commercialized FBR cycle system will be proposed. (author)

  7. Analysis of Technical Feasibility of Traveling Wave Reactor

    International Nuclear Information System (INIS)

    Kim, Sang Ji; Yoo, Jae Woon; Bae, In Ho

    2011-01-01

    The status and trend of TWR, patent status and its major technical characteristics were examined in this study. Main technical features of traveling wave reactor can be characterized as a reactor operation without refueling up to the reactor life more than 60 years and TWR utilizes depleted uranium which would be produced from the enrichment process as a byproduct. Enriched fuel is only loaded to an igniter which is required for initiation of burning wave. In this study, quantitative analysis of TWR arising from the technical features was carried out in terms of resource utilization, safety and integrity, and proliferation resistance. In parallel with the concept review of TerraPower SWR design concepts, independent analysis of SWR design by altering a design specification and operation strategy was done in this study. The fuel rod design of SWR was also investigated based on the current database of fuel irradiation and performance. The technical issues of TWR or SWR which should be prior to detailed research and development can be summarized as follows: ·Strong physical protection is required during the shuffling or in-service inspection period to improve the proliferation resistance. ·New flow control logic or device is required for distributing the assembly-wise flow to be corresponded with power swing of fuel assembly. ·High integrity cladding material need to be developed for covering the high fast neutron fluence more than three times of current limit which result from the high burnup and long fuel cycle. The metal fuel under the high burnup condition should be validated through the irradiation test

  8. Material Identification Technology (MIT) concept technical feasibility study

    International Nuclear Information System (INIS)

    Jones, J.L.; Harker, Y.D.; Yoon, W.Y.; Johnson, L.O.

    1993-09-01

    The Idaho National Engineering Laboratory (INEL) has initiated the design and development of a novel pulsed accelerator-based, active interrogation concept. The proposed concept, referred to as the Material Identification Technology (MIT), enables rapid (between accelerator pulses), non-destructive, elemental composition analysis of both nuclear and non-nuclear materials. Applications of this technique include material monitoring in support of counter-proliferation activities, such as export controls (at domestic and international inspection locations), SNM controls, nuclear weapon dismantlement, and chemical weapon verification. Material Identification Technology combines a pulsed, X-ray source (an electron accelerator) and a gamma detection system. The accelerator must maximize neutron production (pulse width, beam current, beam energy, and repetition rate) and minimize photon dose to the object. Current available accelerator technology can meet these requirements. The detection system must include detectors which provide adequate gamma energy resolution capability, rapid recovery after the initial X-ray interrogation pulse, and multiple single gamma event detection between accelerator pulses. Further research is required to develop the detection system. This report provides the initial feasibility assessment of the MIT concept

  9. Updated (BP3) Technical and Economic Feasibility Study - Electrochemical Membrane for Carbon Dioxide Capture and Power Generation

    Energy Technology Data Exchange (ETDEWEB)

    Ghezel-Ayagh, Hossein [FuelCell Energy, Inc., Danbury, CT (United States)

    2017-12-21

    This topical report summarizes the results of an updated Technical & Economic Feasibility Study (T&EFS) which was conducted in Budget Period 3 of the project to evaluate the performance and cost of the Electrochemical Membrane (ECM)-based CO2 capture system. The ECM technology is derived from commercially available inorganic membranes; the same used in FuelCell Energy’s commercial fuel cell power plants and sold under the trade name Direct FuelCell® (DFC®). The ECM stacks are utilized in the Combined Electric Power (generation) And Carbon dioxide Separation (CEPACS) systems which can be deployed as add-ons to conventional power plants (Pulverized Coal, Combined Cycle, etc.) or industrial facilities to simultaneously produce power while capturing >90% of the CO2 from the flue gas. In this study, an ECM-based CEPACS plant was designed to capture and compress >90% of the CO2 (for sequestration or beneficial use) from the flue gas of a reference 550 MW (nominal, net AC) Pulverized Coal (PC) Rankine Cycle (Subcritical steam) power plant. ECM performance was updated based on bench scale ECM stack test results. The system process simulations were performed to generate the CEPACS plant performance estimates. The performance assessment included estimation of the parasitic power consumption for CO2 capture and compression, and the efficiency impact on the PC plant. While the ECM-based CEPACS system for the 550 MW PC plant captures 90% of CO2 from the flue gas, it generates additional (net AC) power after compensating for the auxiliary power requirements of CO2 capture and compression. An equipment list, ECM stacks packaging design, and CEPACS plant layout were developed to facilitate the economic analysis. Vendor quotes were also solicited. The economic feasibility study included estimation of CEPACS plant capital cost, cost of electricity (COE) analyses and estimation of cost per ton of CO2

  10. Technical study report on fuel fabrication system

    International Nuclear Information System (INIS)

    Kono, Shusaku; Tanaka, Kenya; Ono, Kiyoshi; Iwasa, Katsuyoshi; Hoshino, Yasushi; Shinkai, Yasuo

    2000-07-01

    The feasibility study of FBR and related fuel cycle is performed for developing the FBR recycle system which ensures safety, economic competitiveness, efficient utilization of resources, reduction of environmental burden and enhancement of nuclear non-proliferation under consistency of FBR reactor and fuel cycle systems. In this study, a conceptual design study and system characteristics evaluation are conducted for fuel fabrication systems of pellet process, vibropack process for oxide and nitride fuel and casting process for metal fuel. Technical issues in each process are also extracted. In 1999 fiscal year, a conceptual design study were conducted for the fuel fabrication plants adopting (1) the short pellet process which simplifies the conventional MOX pellet fabrication processes, (2) vibropack processes of aqueous gelation process, improved RIAR process, improved ANL process and fluoride volatility process, (3) casting processes of injection process, centrifuging process. As a result, attainable perspective was obtained for each fuel fabrication system through the evaluation of apparatuses, layout and facility volume, etc. In each fuel fabrication system, technical issues for practical use were made clear. Hereafter, more detailed study will be performed for each system, and research programs for phase II study will be planned. (author)

  11. Preliminary carbon dioxide capture technical and economic feasibility study evaluation of carbon dioxide capture from existing fired plants by hybrid sorption using solid sorbents

    Energy Technology Data Exchange (ETDEWEB)

    Benson, Steven; Envergex, Srivats; Browers, Bruce; Thumbi, Charles

    2013-01-01

    Barr Engineering Co. was retained by the Institute for Energy Studies (IES) at University of North Dakota (UND) to conduct a technical and economic feasibility analysis of an innovative hybrid sorbent technology (CACHYS™) for carbon dioxide (CO2) capture and separation from coal combustion–derived flue gas. The project team for this effort consists of the University of North Dakota, Envergex LLC, Barr Engineering Co., and Solex Thermal Science, along with industrial support from Allete, BNI Coal, SaskPower, and the North Dakota Lignite Energy Council. An initial economic and feasibility study of the CACHYS™ concept, including definition of the process, development of process flow diagrams (PFDs), material and energy balances, equipment selection, sizing and costing, and estimation of overall capital and operating costs, is performed by Barr with information provided by UND and Envergex. The technology—Capture from Existing Coal-Fired Plants by Hybrid Sorption Using Solid Sorbents Capture (CACHYS™)—is a novel solid sorbent technology based on the following ideas: reduction of energy for sorbent regeneration, utilization of novel process chemistry, contactor conditions that minimize sorbent-CO2 heat of reaction and promote fast CO2 capture, and a low-cost method of heat management. The technology’s other key component is the use of a low-cost sorbent.

  12. Technical feasibility of the Diamex process

    International Nuclear Information System (INIS)

    Sorel, Ch

    2007-01-01

    Full text of publication follows. The DIAMEX process was developed to facilitate the separation of the trivalent actinides from the trivalent lanthanides. It consists in co-extracting the trivalent actinides and lanthanides using a diamide extractant: Di-Methyl Di-Octyl Hexyl Ethoxy Malonamide (DMDOHEMA). The flow-sheet comprises: Co-extraction at high acidity (3 M HNO 3 ) of the trivalent actinides and lanthanides by the diamide; scrubbing of some fission products (Zr, Mo, Fe, Pd) by a mixture of oxalic acid and HEDTA, followed by de-acidification to prepare for the next step; stripping of the actinides + lanthanides at low acidity; solvent treatment prior to recycling. This flow-sheet was successfully tested at laboratory scale from 1999 to 2003 in mixer-settlers and subsequently in ECLHA centrifugal extractors on active solutions from the dissolution of actual spent fuel samples. Actinide recovery factors above 99.9% were obtained with high purification factors for spurious fission products. The main objectives of the final ''technical feasibility'' demonstration tests at the end of 2005 with a PUREX raffinate solution were to test continuous solvent recycling (not included during the earlier tests) and to carry out essential operations in continuous contactors representative of pulsed columns that could be used at industrial scale. We therefore decided to carry out the demonstration in the shielded process line (CBP) with some of the devices already used for a PUREX test. During these tests the first two steps in the flow-sheet were therefore carried out in pulsed columns 4 meters high; An+Ln stripping was performed in mixer-settlers and the solvent treatment in ECRAN. The americium and curium recovery yield exceeded 99.9% and the decontamination factors obtained at the end of the test with respect to the fission products Zr, Mo and Fe were 800, 100 and 10, respectively. (author)

  13. Feasibility of Computer Processing of Technical Information on the Design of Instructional Systems. Final Report for the Period 1 July 1972 through 31 March 1973.

    Science.gov (United States)

    Scheffler, F. L.; And Others

    A feasibility study examined the capability of a computer-based system's handling of technical information pertinent to the design of instructional systems. Structured interviews were held to assess the information needs of both researchers and practitioners and an investigation was conducted of 10 computer-based information storage and retrieval…

  14. Feasibility studies and technological innovation

    DEFF Research Database (Denmark)

    Hvelplund, Frede Kloster; Lund, Henrik; Sukkumnoed, Decharut

    2004-01-01

    The chapter offers a tool to conduct feasibility studies and focuses on how to make feasibility studies in a situation with environmental concerns, in which technological innovation and institutional chnages are among the objectives.......The chapter offers a tool to conduct feasibility studies and focuses on how to make feasibility studies in a situation with environmental concerns, in which technological innovation and institutional chnages are among the objectives....

  15. Water reuse in the Apatlaco River Basin (México): a feasibility study.

    Science.gov (United States)

    Moeller-Chávez, G; Seguí-Amórtegui, L; Alfranca-Burriel, O; Escalante-Estrada, V; Pozo-Román, F; Rivas-Hernández, A

    2004-01-01

    The aim of this work is to determine the technical and economic feasibility of implementing different reclamation and reuse projects that improve the quality of the Apatlaco river basin located in the central part of Mexico. A special methodology based on a decision support system was developed. This methodology allows to decide if it is convenient or not to finance a reclamation or reuse project for the most common water uses in the basin. This methodology is based on the net present value criteria (NPV) of the effective cash flow during the useful life of the project. The results obtained reveal a technical and economical feasibility for industrial reuse in Jiutepec and for agricultural reuse in Zacatepec and Emiliano Zapata. On the other hand, sanitation projects are not feasible in all cases analyzed. Therefore, Mexican Regulation (Ley Federal de Derechos en Materia de Agua) as currently implemented, does not promote and support this kind of projects.

  16. Feasibility Study to Identify Potential Reductions in Energy Use in Tribal Buildings

    Energy Technology Data Exchange (ETDEWEB)

    Stevens, Willie [Confederated Salish and Kootenai Tribes, Pablo, MT (United States)

    2017-03-30

    Under this project, the Confederated Salish and Kootenai Tribes (CSKT) assessed the technical and economic feasibility of energy efficiency improvements to existing Tribally-owned buildings. The feasibility study followed a systematic approach in identifying, selecting, and ranking recommended measures, recognizing that the appropriateness of a measure would depend not only on technical issues but also on institutional and organizational issues, such as financing options and occupant requirements. The completed study provided the Tribes with the information needed to commit necessary resources to reduce the energy use and cost in approximately 40 Tribal buildings, including the changes that may be needed in each facility’s operation and maintenance and personnel requirements. It also presented an economic analysis of energy-efficiency capital improvements and an annotated list of financing options and possible funding sources for implementation and an overall strategy for implementation. This project was located in various Tribal communities located throughout the Flathead Indian Reservation in Western Montana. Notice: The following is a compilation of Annual Program Review Presentations, Award Modifications, and Quarterly Progress Reports submitted to the Department of Energy’s (DOE) Office of Indian Energy Policy and Programs by the Confederated Salish and Kootenai Tribes under agreement DE-EE0005171. This report covers project activities from September 30, 2011 through December 31, 2014 and has been uploaded to OSTI by DOE as a substitute for the required Final Technical Report which was not received by DOE from the project recipient.

  17. Assessing the feasibility of the Healthy Life in Suriname Study: using advanced hemodynamics to evaluate cardiovascular risk

    NARCIS (Netherlands)

    Aartman, Jet Q.; Diemer, Frederieke S.; Karamat, Fares A.; Bohte, Evelien; Baldew, Sergio M.; Jarbandhan, Ameerani V.; van Montfrans, Gert A.; Oehlers, Glenn P.; Brewster, Lizzy M.

    2017-01-01

    Objectives. To determine the feasibility of assessing population cardiovascular risk with advanced hemodynamics in the Healthy Life in Suriname (HELISUR) study. Methods. This was a preliminary study conducted in May - June 2012 using the Technical-Economic-Legal-Operational-Scheduling (TELOS) method

  18. Installation of a hydrokinetic turbines: technical and economic feasibility; Instalacao de turbinas hidrocineticas: viabilidade tecnica e economica

    Energy Technology Data Exchange (ETDEWEB)

    Els, Rudi Henri van; Vianna, Joao Nildo de Souza [Universidade de Brasilia (UnB), DF (Brazil). Centro de Desenvolvimento Sustentavel; Brasil Junior, Antonio Cesar Pinho [Universidade de Brasilia (UnB), DF (Brazil). Dept. de Engenharia Mecanica

    2008-07-01

    The generation of electric energy with hydrokinetic turbines is a technological option to attend households, communities and small villages in their basic electricity needs. These turbines, that generates power around 1 kW, appeared in the lasts decades as another technological alternative for decentralized electricity generation with diesel fuel generator sets. This article presents the various types of hydrokinetic turbines that exist and details the technical and economic feasibility of the second generation of hydrokinetic turbines designed by the University of Brasilia. The technical requirements on the selection of hydrokinetic sites, along with the diverse forms of fixing and mooring the turbine in the river are also showed. The economic feasibility of the use of this technology is presented along with the calculation of the generation costs accompanied with an assessment of the different items comprising this cost. At the end, this paper closes with a discussion on the management and operation of decentralized electric energy generation systems with renewable sources, showing that there is a need to design appropriate management mechanisms for this kind of situation, taking into account the specific aspects of its supply and principally of its use. (author)

  19. Feasibility assessment of a risk-based approach to technical specifications

    International Nuclear Information System (INIS)

    Atefi, B.; Gallagher, D.W.

    1991-05-01

    To assess the potential use of risk and reliability techniques for improving the effectiveness of the technical specifications to control plant operational risk, the Technical Specifications Branch of the Nuclear Regulatory Commission initiated an effort to identify and evaluate alternative risk-based approaches that could bring greater risk perspective to these requirements. In the first phase four alternative approaches were identified and their characteristics were analyzed. Among these, the risk-based approach to technical specifications is the most promising approach for controlling plant operational risk using technical specifications. The second phase of the study concentrated on detailed characteristics of the real time risk-based approach. It is concluded that a real time risk-based approach to technical specifications has the potential to improve both plant safety and availability. 33 figs., 5 figs., 6 tabs

  20. Laboratory and Feasibility Study for Industrial Wastewater Effluents Treatment by Radiation

    Energy Technology Data Exchange (ETDEWEB)

    Zimek, Z.; Głuszewski, W. [Centre for Radiation Research and Technology, Institute of Nuclear Chemistry and Technology, Warsaw (Poland)

    2012-07-01

    The study of wastewater treatment by radiation regarding chemical processes contribution and physical-chemical separation of highly concentrated non-organic pollutants deposited in specific industrial waste are proposed. Laboratory stand should be build and the study should be performed to confirm possible mechanism of the sedimentation process of nonorganic pollutants during separation initiated by ionizing radiation. Evaluation from technical and economical point of view of this specific radiation technology and feasibility study preparation for industrial facility will be the main output at the final stage of the project. (author)

  1. Laboratory and Feasibility Study for Industrial Wastewater Effluents Treatment by Radiation

    International Nuclear Information System (INIS)

    Zimek, Z.; Głuszewski, W.

    2012-01-01

    The study of wastewater treatment by radiation regarding chemical processes contribution and physical-chemical separation of highly concentrated non-organic pollutants deposited in specific industrial waste are proposed. Laboratory stand should be build and the study should be performed to confirm possible mechanism of the sedimentation process of nonorganic pollutants during separation initiated by ionizing radiation. Evaluation from technical and economical point of view of this specific radiation technology and feasibility study preparation for industrial facility will be the main output at the final stage of the project. (author)

  2. Trans-Caspian gas pipeline feasibility study. Volume 3

    International Nuclear Information System (INIS)

    1999-01-01

    This study, conducted by Enron Engineering and Construction Company, was funded by the US Trade and Development Agency. The study provides detailed information concerning natural gas demand in Turkey and Southern Europe. The purpose of the study is to estimate the rate at which new gas can be absorbed in the Turkish market and be re-exported to the markets in Europe, as well as to forecast Turkish natural gas demand for the period up to 2020. The study also evaluates gas demand and pricing for the market in the 2002--2005 time frame. This is Volume 3 of a 3-volume report, and it is divided into the following sections: (1) Executive Summary; (2) Task C: Technical Feasibility and Preliminary Design; (3) Task F: Project Implementation Strategy

  3. The feasibility study on fuel types for the KALIMER

    International Nuclear Information System (INIS)

    Hwang, W.; Nam, C.; Yim, J. S.; Na, B. C.; Hahn, D. H.; Kim, Y. I.; Kim, Y. C.; Park, C. K.

    1997-08-01

    The economics of LMR is largely dependent on the construction cost of the power plant, and the fuel cycle options usually constitute 20 to 30 % of total electricity generation cost. The choice of fuel cycle technology and the fuel type is important in order to develop a LMR with better economics, performance and safety. The LMR fuel types, whose performances have been proven up to 15 at% burnup, are MOX and IFR metal fuel. The base alloy, binary (U-10% Zr) metal fuel with HT9 is used as structural materials of KALIMER. The design concept of KALIMER fuel has been established through the investigation of technical feasibilities on the fuel and recycle systems for MOX and IFR metal fuel. According to the results of comparative analysis for MOX and metal fuel, metal fuel is better than MOX in view of safety, in-reactor performance, nuclear characteristics, economics and non-proliferation, while MOX fuels have advantages in the developmental status and technical cooperation potential. The overall performance of binary (U-10% Zr) metal fuel with HT9 cladding, which is a potential start-up fuel for KALIMER, is not only superior to that of MOX fuel, but also has enough technical feasibility in its high-burnup performance, safety and economics. (author). 54 ref., 13 tabs., 20 figs

  4. Feasibility of biomass heating system in Middle East Technical University, Northern Cyprus Campus

    Directory of Open Access Journals (Sweden)

    Samuel Asumadu-Sarkodie

    2016-12-01

    Full Text Available Global interest in using biomass feedstock to produce heat and power is increasing. In this study, RETScreen modelling software was used to investigate the feasibility of biomass heating system in Middle East Technical University, Northern Cyprus Campus. Weiss Kessel Multicratboiler system with 2 MW capacity using rice straw biomass as fuel and 10 units of RBI® CB0500 boilers with 144 kW capacity using natural gas as fuel were selected for the proposed biomass heating system. The total cost of the biomass heating project is US$ 786,390. The project has a pre-tax and after tax internal rate of return (IRR of 122.70%, simple payback period of 2.54 years, equity payback period of 0.83 year, a net present value of US$ 3,357,138.29, an annual lifecycle savings of US$ 262,617.91, a benefit-cost ratio of 21.83, an electricity cost of $0/kWh and a GHG reduction cost of −204.66 $/tCO₂. The annual GHG emission reduction is 1,283.2 tCO₂, which is equivalent to 118 hectares of forest absorbing carbon. The development and adoption of this renewable energy technology will save costs on buying conventional type of heating system and result in a large technical and economic potential for reducing greenhouse gas emissions which will satisfy the sustainable development goals.

  5. Conceptual design of small-sized HTGR system (4). Plant design and technical feasibility

    International Nuclear Information System (INIS)

    Ohashi, Hirofumi; Sato, Hiroyuki; Yan, Xing L.; Sumita, Junya; Nomoto, Yasunobu; Tazawa, Yujiro; Noguchi, Hiroki; Imai, Yoshiyuki; Tachibana, Yukio

    2013-09-01

    Japan Atomic Energy Agency (JAEA) has started a conceptual design of a 50MWt small-sized high temperature gas cooled reactor (HTGR) for steam supply and electricity generation (HTR50S), which is a first-of-kind of the commercial plant or a demonstration plant of a small-sized HTGR system for steam supply to the industries and district heating and electricity generation by a steam turbine, to deploy in developing countries in the 2020s. HTR50S was designed for steam supply and electricity generation by the steam turbine with the reactor outlet temperature of 750degC as a reference plant configuration. On the other hand, the intermediate heat exchanger (IHX) will be installed in the primary loop to demonstrate the electricity generation by the helium gas turbine and hydrogen production by thermochemical water splitting by utilizing the secondary helium loop with the reactor outlet temperature of 900degC as a future plant configuration. The plant design of HTR50S for the steam supply and electricity generation was performed based on the plant specification and the requirements for each system taking into account for the increase of the reactor outlet coolant temperature from 750degC to 900degC and the installation of IHX. The technical feasibility of HTR50S was confirmed because the designed systems (i.e., reactor internal components, reactor pressure vessel, vessel cooling system, shutdown cooling system, steam generator (SG), gas circulator, SG isolation and drainage system, reactor containment vessel, steam turbine and heat supply system) satisfies the design requirements. The conceptual plant layout was also determined. This paper provides the summary of the plan design and technical feasibility of HTR50S. (author)

  6. Computing with words to feasibility study of software projects

    Directory of Open Access Journals (Sweden)

    Marieta Peña Abreu

    2017-02-01

    Full Text Available Objective: This paper proposes a method to analyze the technical, commercial and social feasibility of software projects in environments of uncertainty. It allows working with multiple experts and multiple criteria and facilitates decision-making. Method: The proposal contains two phases, first the necessary information is collected and in second place projects are evaluated using 2-tuple linguistic representation model. The experts are selected by analyzing their curricular synthesis. The evaluation criteria are defined using the technique Focus Group and weighted in the interval (0,1 according to their importance. three domains are offered to express the preferences: numeric, interval-valued and linguistic. For aggregation extended arithmetic mean and weighted average extended are used, preventing the loss of information. A 2-tuple (feasibility, precision is obtained as a result for each project. Results: The evaluation of P1 project was a very high feasibility with -0,33 of precision. The P2 project obtained a high feasibility with 0,38 of precision and P3 project achieved a medium feasibility with -0,21 of precision. Conclusions: This method is favorable for software projects feasibility analysis with presence of multiple experts and criteria, in environments of uncertainty. It tries heterogeneous assessments without loss of information. Their results are consistent and useful for decision makers.

  7. Morbidity follow-up feasibility study

    International Nuclear Information System (INIS)

    Carpenter, M.

    1988-02-01

    The report reviews the available sources of data within Canada for undertaking morbidity follow-up studies to both supplement and complement studies using Canadian mortality data. Such studies would permit earlier detection and more sensitive measures of differences in risk for exposures to radiation and allow timely measures to be taken to minimize any occupational and environmental health risk to radiation workers. The technical feasibility of using these sources was reviewed using the criteria of adequate personal identifying information, automation of data records, file size and the accuracy of the morbidity diagnosis information. At the present time certain of the provincial cancer registry files meet these criteria best. A work plan was prepared suggesting a morbidity pilot study to clarify the role of occupational factors in the incidence of cancer among radiation workers using the Alberta Cancer Registry file and the National Dose Registry (NDR) file of radiation workers. For the longer term a full cohort study using the National Cancer Incidence Reporting System (NCIRS) and the NDR workers as the study population would provide information on all radiation workers on a national basis. A work plan was prepared and some initial format conversion of historical data was undertaken to begin developing the NCIRS into a data base suitable for long-term health studies

  8. Experiences of a feasibility study of children with albinism in Zimbabwe: a discussion paper.

    Science.gov (United States)

    Taylor, Julie S; Lund, Patricia

    2008-08-01

    Feasibility studies are often a helpful prelude to constructing fundable research proposals. Where the intended research is in a foreign country, focuses on a vulnerable population, and is aggravated by political and pragmatic challenges, feasibility studies become essential. Albinism, a genetic condition of reduced melanin synthesis, is a major public health issue in southern Africa. Whilst much is known about the health needs of children with albinism, little is understood about how to address these effectively in low income countries. Further, the child care and protection needs of children with albinism are largely unexplored. Zimbabwe's current political and economic climate presents additional challenges to research on the topic. The technical, economic, legal, collaborative, operational, schedule and political feasibilities (acronym TELCOSP) to undertaking a study on children with albinism in Zimbabwe were explored over a six week period of fieldwork in the country. Using the TELSCOSP framework allowed a deconstruction of each challenge to provide innovative solutions. The economic and legal feasibility aspects presented some difficulties that will require flexibility and perseverance to overcome. With the assistance of the local communities and people with albinism in Zimbabwe, the obstacles appear surmountable. The feasibility study provided a productive framework for addressing potential challenges in studying the needs of Zimbabwe's children living with albinism.

  9. Feasibility study on commercialization of fast breeder reactor cycle system. Interim report of phase 2. Technical study report on synthetic evaluation for FBR cycle

    International Nuclear Information System (INIS)

    Shiotani, Hiroki; Ohtaki, Akira; Ono, Kiyoshi; Yasumatsu, Naoto; Kubota, Sadae; Heta, Masanori

    2004-09-01

    This report presents the outline of the development and the results of Synthetic evaluation on the candidate Fast Reactor (FR) cycle system concepts, scenario study on FR cycle deployment and cost-benefit analysis on the candidate FR cycle system concepts in the interim evaluation (FY2001 through FY2003) of the phase 2 of the Japanese 'Feasibility Study on Commercialization of Fast Reactor Cycle System (FS)'. The characteristic evaluation extended to evaluate a new view point of social acceptance besides the viewpoints of safety, economics, reduction of environmental burden, efficient utilization of uranium resource, proliferation resistance, and technical feasibility, which has been considered since the phase 1 of FS. As for the six view points, hierarchy structures and utility functions for quantitative evaluation have been developed and/or improved. Furthermore, the methodology for weighing the viewpoints, which was also developed, made it possible to examine the characteristics of the candidate concepts from all the seven viewpoints. Generally, the FR cycles with sodium-cooled FR were highly evaluated. The characteristic evaluation for alternative power supply systems was also tried in this report for the first time. FR cycle deployment scenarios clarified the necessity of FR cycle deployment and the desirable core features, etc. through the long-term mass flow analysis, which includes comparison among other nuclear fuel cycle schemes and analysis for evaluating the degree to meet future needs, on the typical FR cycle systems. Regarding cost-benefit analysis, both the amount of the cost estimated by the past R and D and the cost in the Road map of FS are used as the investment for FR cycle research and development (R and D), the results showed that the benefit derived from the commercialization of FR cycle will be more than the investment. (author)

  10. FBI fingerprint identification automation study. AIDS 3 evaluation report. Volume 4: Economic feasibility

    Science.gov (United States)

    Mulhall, B. D. L.

    1980-01-01

    The results of the economic analysis of the AIDS 3 system design are presented. AIDS 3 evaluated a set of economic feasibility measures including life cycle cost, implementation cost, annual operating expenditures and annual capital expenditures. The economic feasibility of AIDS 3 was determined by comparing the evaluated measures with the same measures, where applicable, evaluated for the current system. A set of future work load scenarios was constructed using JPL's environmental evaluation study of the fingerprint identification system. AIDS 3 and the current system were evaluated for each of the economic feasibility measures for each of the work load scenarios. They were compared for a set of performance measures, including response time and accuracy, and for a set of cost/benefit ratios, including cost per transaction and cost per technical search. Benefit measures related to the economic feasibility of the system are also presented, including the required number of employees and the required employee skill mix.

  11. Technical study report on reprocessing system

    International Nuclear Information System (INIS)

    Tanaka, Hiroshi; Kasai, Yoshimitsu; Kawamura, Fumio

    2000-07-01

    The feasibility studies on commercialized fast breeder reactor (FBR) recycle system, in which reactor system and recycle technologies are related on consideration, are performed considering the attainable perspectives for the followings: ensuring safety, economic competitiveness to future LWRs, efficient utilization of resources, reduction of environmental burden, and enhancement of nuclear non-proliferation. In the studies of Reprocessing system of FBR, evaluation was made for the non-aqueous reprocessing of pyrochemical and fluoride volatility process and also for the aqueous reprocessing with a view to streamlining. As a result, it was estimated that each system has prospects of coming into practical use in terms of technique. In the economical efficiency assessment, it was estimated to have economic competitiveness to future LWRs. And the technical research items of each system are picked out. Hereafter, more detail design study will be performed for each system. (author)

  12. Feasibility study of gasification of oil palm fronds

    Directory of Open Access Journals (Sweden)

    S.A. Sulaiman

    2015-12-01

    Full Text Available Considering the large and consistent supply, oil palm fronds could be a promising source of biomass energy through gasification. There is very scarce information on the characteristics of oil palm fronds, which is vital in deciding if such biomass is technically suitable for gasification. In the present work, the feasibility of oil palm fronds for biomass gasification is studied. The study is conducted experimentally via standard tests to determine their thermochemical characteristics. Ultimate analysis is conducted to determine the contents of carbon, nitrogen, hydrogen and sulphide in oil palm fronds. Proximate analysis is performed to identify the burning characteristics of the biomass. The energy content in the fronds is determined by using a bomb calorie meter and is around 18 MJ/kg. The ignitability of the fronds is also studied experimentally to assess the ease to start-up combustion of the fronds. The characteristics of the flame of the resulting syngas from gasification of oil palm fronds are qualitatively studied. Simulated syngas composition study reveals potentials of 22% CO, 1.3% H2, 18.5% CO2 and traces of CH4. The study is extended to computer simulation to predict composition of the syngas. It is found from this work that oil palm fronds are feasible for gasification and has a good potential as a renewable energy source.

  13. A preliminary economic feasibility assessment of nuclear desalination in Madura Island

    International Nuclear Information System (INIS)

    Kim, S.-H.; Hwang, Y.-D.; Konishi, T.; Hudi Hastowo

    2005-01-01

    A joint study between KAERI and BATAN, which is entitled 'A preliminary economic feasibility assessment of nuclear desalination in Madura Island', is being conducted under the framework of the Interregional Technical Cooperation Project of IAEA, signed on Oct. 10, 2001 at IAEA. The duration of the project is January 2002 to December 2004. An economic feasibility of nuclear desalination using system-integrated modular advanced reactor (SMART), which will provide Madura Island with electricity and potable water and also support industrialisation and tourism, will be assessed during the project. The scope of this joint study includes the analyses for the short- and long-term energy and water demand as well as the supply plan for Madura Island, evaluation of the site characteristics, environmental impacts and health aspects, technical and economic evaluation of SMART and its desalination system, including the feasibility of its being identified on the Madura Island. KAERI and BATAN are cooperating in conducting a joint study, and IAEA provides technical support and a review of the study products. This paper presents the interim results of the joint study by focussing on the technical and economic aspects of nuclear desalination using SMART in Madura Island. (author)

  14. Eye-tracking computer systems for inpatients with tetraplegia: findings from a feasibility study.

    Science.gov (United States)

    van Middendorp, J J; Watkins, F; Park, C; Landymore, H

    2014-12-02

    Study design:A longitudinal, prospective, self-controlled cohort study.Objectives:To determine (1) the preliminary benefits of using eye-tracking computer systems (ETCSs) among inpatients with tetraplegia and (2) the feasibility of carrying out a well-powered randomized controlled trial.Setting:Specialist Spinal Cord Injuries Centre, United Kingdom; 6 months during 2013-2014.Methods:Individuals with tetraplegia who were admitted to the center and enrolled in this study were trained and allowed to use the ETCS (Tobii Eyegaze C15 System) twice a week for a duration of 10 weeks. Standardized training modules were developed and offered to all study participants. Study feasibility indicators as well as the Appraisals of Disability: Primary and Secondary Scale, Hospital Anxiety and Depression Scale and the Assistive Technology Device Predisposition Assessment questionnaire scores were taken before and after study enrollment.Results:A total of 31 inpatients with tetraplegia were screened. Although 14 patients (45%) met the study eligibility criteria, 6 patients (19%) consented to be enrolled in the study. Three participants did not complete the planned training schedule because of medical, technical and logistic reasons. Although half of the participants agreed that the ETCS under study was easy to use, no substantial improvements were seen in terms of psychological outcomes, appraisals of disability or independence.Conclusions:The conduct of a controlled trial evaluating the benefits of using ETCSs among newly injured patients with tetraplegia comes with considerable feasibility challenges. Until substantial technical improvements of ETCSs have been implemented, future research should initially focus on those individuals with tetraplegia who are living in the community and who have expressed a need to enhance their computer access and communication skills.Spinal Cord advance online publication, 2 December 2014; doi:10.1038/sc.2014.219.

  15. Assessing the feasibility of the Healthy Life in Suriname Study: using advanced hemodynamics to evaluate cardiovascular risk

    Directory of Open Access Journals (Sweden)

    Jet Q. Aartman

    2017-06-01

    Full Text Available ABSTRACT Objectives To determine the feasibility of assessing population cardiovascular risk with advanced hemodynamics in the Healthy Life in Suriname (HELISUR study. Methods This was a preliminary study conducted in May – June 2012 using the Technical-Economic-Legal-Operational-Scheduling (TELOS method to assess the feasibility of the HELISUR—a large-scale, cross-sectional population study of cardiovascular risk factors and disease in Suriname. Suriname, a middle-income country in South America with a population of mostly African and Asian ethnicity, has a high risk of cardiovascular disease. A total of 135 volunteers 18 – 70 years of age participated. A health questionnaire was tested in a primary health care center, and non-invasive cardiovascular evaluations were performed in an academic health center. The cardiovascular evaluation included sitting, supine, and standing blood pressure, and intermediate endpoints, such as cardiac output, peripheral vascular resistance, pulse wave velocity, and augmentation index. Results The TELOS testing found that communicating by cellular phone was most effective for appointment adherence, and that completion of the questionnaire often required assistance from a trained interviewer; modifications to improve the clarity of the questions are recommended. Regarding the extended cardiovascular assessments of peripheral and central hemodynamics, the findings showed these to be technically and operationally feasible and well tolerated by participants, in terms of burden and duration. Conclusions Findings of this feasibility assessment indicate that large-scale, detailed evaluations of cardiovascular risk, including a questionnaire and advanced central and peripheral hemodynamics, are feasible in a high-risk population in a middle-income setting.

  16. Aging/Systems Interaction Study, Component Residual Lifetime Evaluation and Feasibility of Relicensing. Progress report, FY 1985

    International Nuclear Information System (INIS)

    Close, J.A.; Jacobs, P.T.; Korth, G.E.; Mudlin, J.M.; Server, W.L.; Spaletta, H.W.

    1985-10-01

    This report documents the work performed on four research tasks in Fiscal Year 1985 (FY-1985) which were part of the Aging/Systems Interaction Study, Component Residual Lifetime Evaluation and Feasibility of Relicensing Project. The technical and management/institutional objectives for the project are described, followed by a description of the results of each task. The work on Task 1 involved identifying and prioritizing new research activities for the Nuclear Regulatory Commission (NRC) Nuclear Plant Aging Research (NPAR) Program. A proposed methodology and plan for aging-system interaction studies was developed in Task 2. The description of Task 3 work comprises a summary of nuclear plant life extension activities in the US, the technical basis associated with the residual life of metallic materials and a proposed plan for research on residual life assessment. Task 4 describes the initial evaluation of selected Standard Review Plan (NUREG-0800) sections to investigate the feasibility of relicensing. 14 refs., 13 figs., 20 tabs

  17. The offshore disposal of radioactive waste by drilled emplacement: A feasibility study

    International Nuclear Information System (INIS)

    Bury, M.R.C.

    1985-01-01

    This book is a report, based on a study by Taylor Woodrow Construction Limited, on the overall feasibility of the disposal of high-level radioactive waste in boreholes drilled deep into the ocean bed. The work comprises an engineering appraisal of the disposal process with a view to establishing technical and operational feasibility and providing overall cost information to enable an economic assessment to be made. Contents: Summary report; Reference criteria; Drilling operation; Transfer of radioactive waste, personnel and other supplies; Handling of radioactive waste on board; Lowering strings of canisters; Emplacement and backfilling of canisters; Preliminary design of marine platform; Retrieval of flasks or canisters lost or misplaced; Variations to the features of the lowering system; Logistics of the operation; Construction cost estimate; Operational costs; Appendix

  18. [Technical feasibility of the implantation of a monorail stent system into the renal arteries without pre-dilatation].

    Science.gov (United States)

    Neumann, C; Gschwendtner, M; Karnel, F; Mair, J; Dorffner, G; Dorffner, R

    2005-01-01

    To evaluate the technical feasibility of the implantation of the monorail RX Herculink system into the renal arteries without pre-dilatation. Forty-two patients (mean age 71 years) from four centers with a total of 44 renal artery stenoses underwent implantation of the RX Herculink stent. The mean grade of the stenosis was 83.8 %, the mean length 7.5 mm. The stenoses were ostial in 38 cases and in immediate proximity to the ostium in 6 cases. The mean follow-up-period was 57 weeks (24 - 176 weeks). In 42 cases, the implantation was successful without pre-dilatation. In 2 cases, pre-dilatation was carried out. In none of the cases, detachment of the stent from the balloon was observed. In one stenosis with a length of 17 mm, implantation of two stents was performed. In 9 cases, post-dilatation with a larger balloon or higher balloon pressure was necessary. Residual stenoses exceeding 30 % were not observed. Two patients developed local bleeding at the puncture site. During the follow-up, restenoses were observed in 5 stents after 26 to 126 weeks, which necessitated a second intervention in 3 cases (PTA in 2 cases, re-stenting in 1 case). The primary patency rate after 6 and 12 months was 0.92 +/- 0.056 according to Kaplan-Meier, the secondary patency rate after 6 and 12 months was 1.0 +/- 0.0. Implantation of the RX Herculink stent system into the renal arteries without pre-dilatation is technically feasible and safe. Even without pre-dilatation, the stent-system can be advanced through the stenosis without detachment. The complication rate is low. Our clinical results are comparable to previous studies.

  19. Technical developments of solar energy collectors in the Netherlands

    NARCIS (Netherlands)

    Oversloot, H.P.; Geus, A.C. de

    1996-01-01

    Recent research by TNO covered two different technical developments for thermal solar energy systems. One concerns a feasibility study into an all plastic spectral selective absorber, the other is a feasibility study for an overheating protection device based on heatpipe techniques. Earlier studies

  20. Technical study of torsional transit-time magnetic pumping (TTMP) heating. Application for PETULA and large machines

    International Nuclear Information System (INIS)

    Brossaud, J.; Lanier, R.; Perin, J.P.; Rey, G.

    1980-11-01

    This report describes a computer program which determines the RF current distributions and the corresponding voltage and dissipated powers in the conductors for the application of torsional TTMP heating. The results fit well with a Petula-scale experiments. Two prototype coils have been studied and tested for Petula. The application for JET points out the main technical problems which need further developments to ensure the technical feasibility of this method [fr

  1. The Role of Feasibility Studies To Enhance The Natural Gas Industry

    International Nuclear Information System (INIS)

    Soliman, M.; Soliman, A.

    2004-01-01

    The purpose of this paper is to shred some light on the key issues of the gas projects feasibility studies and to answer on this question W hat is the impact of the economic, financial and marketing studies on the transmission and distribution gas project's feasibility studies in Egypt? One of the obstacles to a beneficial gas project developing is, undoubtedly, the lack of knowledge in developing countries of how to formulate a project in such a way that its potential profitability whether from a private or social viewpoint, can be estimated from as firm a basis as possible. While there has been some improvement in these areas, this is still broadly true. The basis for an efficient gas project should not only depend on technical and engineering skills, but also on sound economic, marketing, financial and legal studies and expertise. Along with these sophisticated studies, another difficult but equally important subject has to be deeply assessed, namely the element of risk. A common mis perception in the feasibility studies domain is that some people think that it should only answer the question of whether the project is profitable or not, while its main goal is to explore the question of whether the , project represents the best possible use of the limited (scarce).resources at the country's disposal (specialized manpower, capital, natural resources)

  2. Technical assessment study on pool-type LMFBR

    International Nuclear Information System (INIS)

    1986-01-01

    Technical assessment study on pool-type LMFBR was started in 1984 FY, inheriting the products from the Feasibility study, in order to accomplish cost reduction of reactor structure and enhanced structural reliability. This study consists of four major subjects; aseismic design development, component design optimization, high temperature structural design optimization and thermal hydraulics design optimization. In 1985 FY numbers of large model tests and analytical evaluations have been performed based on the prospects obtained in the first year's study. These tests and analyses have produced a lot of findings in each subject. They are concerning; (1) the effect of various building structures and analysis methods on floor response reduction, and data for evaluation of aseismic design concepts and structural integrity to seismic loading in the aseismic design development study. (2) data for evaluation of size reduction of main components in the reactor vessel, and heat transfer data required for structural integrity evaluation in the component design optimization study. (3) data for verification of inelastic analysis method, and assurance of technical applicability of disimilar weld in the high temperature structural design optimization study. (4) the effect of component size and location on thermal hydraulic characteristics, and data of thermal hydraulic similarity in thermal hydraulic design optimization study. This report summarizes the results obtained in 1985 FY. (author)

  3. Feasibility study report for Operable Unit 4: Volume 1

    International Nuclear Information System (INIS)

    1994-02-01

    This report documents the Feasibility Study (FS) phase of the Fernald Environmental Management Project (FEMP) Operable Unit 4 Remedial Investigation/Feasibility Study (RI/FS) Program. The FEMP, formerly known as the Feed Materials Production Center (FMPC), is a US Department of Energy (DOE) facility that operated from 1952 to 1989. The facility's primarily function was to provide high purity uranium metal products to support United States defense programs. Production operations were suspended in 1989 to focus on environmental restoration and waste management activities at the facility. The RI/FS is being conducted pursuant to the terms of a Consent Agreement between DOE and the US Environmental Protection Agency (EPA) under Sections 120 and 106(a) of the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA), as amended. The Ohio Environmental Protection Agency (OEPA) is also participating in the RI/FS process at the FEMP through direct involvement in program review meetings and technical review of project documentation. The objective of the RI/FS process is to gather information to support an informed risk management decision regarding which remedy appears to be the most appropriate action for addressing the environmental concerns identified at the FEMP

  4. Feasibility study of a hybrid wind turbine system – Integration with compressed air energy storage

    International Nuclear Information System (INIS)

    Sun, Hao; Luo, Xing; Wang, Jihong

    2015-01-01

    Highlights: • A new hybrid wind turbine system is proposed and feasibility study if conducted. • A complete mathematical model is developed and implemented in a software environment. • Multi-mode control strategy is investigated to ensure the system work smoothly and efficiently. • A prototype for implementing the proposed mechanism is built and tested as proof of the concept. • The proposed system is proved to be technically feasible with energy efficiency around 50%. - Abstract: Wind has been recognized as one of major realistic clean energy sources for power generation to meet the continuously increased energy demand and to achieve the carbon emission reduction targets. However, the utilisation of wind energy encounters an inevitable challenge resulting from the nature of wind intermittency. To address this, the paper presents the recent research work at Warwick on the feasibility study of a new hybrid system by integrating a wind turbine with compressed air energy storage. A mechanical transmission mechanism is designed and implemented for power integration within the hybrid system. A scroll expander is adopted to serve as an “air-machinery energy converter”, which can transmit additional driving power generalized from the stored compressed air to the turbine shaft for smoothing the wind power fluctuation. A mathematical model for the complete hybrid process is developed and the control strategy is investigated for corresponding cooperative operations. A prototype test rig for implementing the proposed mechanism is built for proof of the concept. From the simulated and experimental studies, the energy conversion efficiency analysis is conducted while the system experiences different operation conditions and modes. It is proved that the proposed hybrid wind turbine system is feasible technically

  5. How to Train an Injured Brain? A Pilot Feasibility Study of Home-Based Computerized Cognitive Training.

    Science.gov (United States)

    Verhelst, Helena; Vander Linden, Catharine; Vingerhoets, Guy; Caeyenberghs, Karen

    2017-02-01

    Computerized cognitive training programs have previously shown to be effective in improving cognitive abilities in patients suffering from traumatic brain injury (TBI). These studies often focused on a single cognitive function or required expensive hardware, making it difficult to be used in a home-based environment. This pilot feasibility study aimed to evaluate the feasibility of a newly developed, home-based, computerized cognitive training program for adolescents who suffered from TBI. Additionally, feasibility of study design, procedures, and measurements were examined. Case series, longitudinal, pilot, feasibility intervention study with one baseline and two follow-up assessments. Nine feasibility outcome measures and criteria for success were defined, including accessibility, training motivation/user experience, technical smoothness, training compliance, participation willingness, participation rates, loss to follow-up, assessment timescale, and assessment procedures. Five adolescent patients (four boys, mean age = 16 years 7 months, standard deviation = 9 months) with moderate to severe TBI in the chronic stage were recruited and received 8 weeks of cognitive training with BrainGames. Effect sizes (Cohen's d) were calculated to determine possible training-related effects. The new cognitive training intervention, BrainGames, and study design and procedures proved to be feasible; all nine feasibility outcome criteria were met during this pilot feasibility study. Estimates of effect sizes showed small to very large effects on cognitive measures and questionnaires, which were retained after 6 months. Our pilot study shows that a longitudinal intervention study comprising our novel, computerized cognitive training program and two follow-up assessments is feasible in adolescents suffering from TBI in the chronic stage. Future studies with larger sample sizes will evaluate training-related effects on cognitive functions and underlying brain structures.

  6. Feasibility study for the Nuclear Research Centre of the Nuclear Energy Commission

    International Nuclear Information System (INIS)

    1985-01-01

    The feasibility study was carried out in order to evaluate the possibility of building a Nuclear Research Centre in Uruguay, which would support a wide range of nuclear related technological activities. A market research was carried out, of the products to be manufactured at the Nuclear Centre, regarding the size of production. A detailed list of the main products considered is enclosed. The siting study was performed through the analysis of the incidental factors, such as environment, technical scope and socio-ecomonic factors. An engineering study for the main installations was done. The investment and financial sources were also studied

  7. MRI-guided percutaneous retrograde drilling of osteochondritis dissecans of the talus: a feasibility study

    International Nuclear Information System (INIS)

    Kerimaa, Pekka; Ojala, Risto; Markkanen, Paula; Tervonen, Osmo; Blanco Sequeiros, Roberto; Sinikumpu, Juha-Jaakko; Korhonen, Jussi; Hyvoenen, Pekka

    2014-01-01

    The purpose of this study was to evaluate the feasibility of MRI guidance for percutaneous retrograde drilling in the treatment of osteochondritis dissecans of the talus (OCDT). Four patients, one juvenile and three adults, with one OCDT lesion each and persisting ankle pain after conservative treatment, were treated with MRI-guided retrograde drilling. All lesions were stable and located in the middle or posterior medial third of the talar dome. Pain relief and the ability to return to normal activities were assessed during clinical follow-up. MRI and plain film radiographs were used for imaging follow-up. Technical success was 100 % with no complications and with no damage to the overlying cartilage. All patients experienced some clinical benefit, although only one had complete resolution of pain and one had a relapse leading to surgical treatment. Changes in the pathological imaging findings were mostly very slight during the follow-up period. MRI guidance seems accurate, safe and technically feasible for retrograde drilling of OCDT. Larger series are needed to reliably assess its clinical value. (orig.)

  8. MRI-guided percutaneous retrograde drilling of osteochondritis dissecans of the talus: a feasibility study

    Energy Technology Data Exchange (ETDEWEB)

    Kerimaa, Pekka; Ojala, Risto; Markkanen, Paula; Tervonen, Osmo; Blanco Sequeiros, Roberto [Oulu University Hospital, Department of Radiology, Oulu (Finland); Sinikumpu, Juha-Jaakko; Korhonen, Jussi [Oulu University Hospital, Department of Paediatric Surgery, Oulu (Finland); Hyvoenen, Pekka [Oulu University Hospital, Department of Surgery, Oulu (Finland)

    2014-07-15

    The purpose of this study was to evaluate the feasibility of MRI guidance for percutaneous retrograde drilling in the treatment of osteochondritis dissecans of the talus (OCDT). Four patients, one juvenile and three adults, with one OCDT lesion each and persisting ankle pain after conservative treatment, were treated with MRI-guided retrograde drilling. All lesions were stable and located in the middle or posterior medial third of the talar dome. Pain relief and the ability to return to normal activities were assessed during clinical follow-up. MRI and plain film radiographs were used for imaging follow-up. Technical success was 100 % with no complications and with no damage to the overlying cartilage. All patients experienced some clinical benefit, although only one had complete resolution of pain and one had a relapse leading to surgical treatment. Changes in the pathological imaging findings were mostly very slight during the follow-up period. MRI guidance seems accurate, safe and technically feasible for retrograde drilling of OCDT. Larger series are needed to reliably assess its clinical value. (orig.)

  9. Feasibility Study Analysis of Establishing Archery Sports Special Place

    Science.gov (United States)

    Tarigan, U. P. P.; Mardhatillah, A.; Budiman, I.; Sembiring, A. C.; Ramadhan, M. S.

    2018-04-01

    This study essentially discusses the basic concepts related to the decision and process of selecting a sports archery business project in order to provide economic and social benefits over time. Archery sports is a sport that requires special skills, both accuracy, coordination mental training and improves the physical condition of the prime. In Medan, it's still a bit of practice archery, but many people love this sport. From the data collected, there are three locations where archery in the city of the field of the Sunggal Knights is located at Jl Tunggul Hitam no.1A, Kec. Medan Sunggal, Avros Educational Park Aval address at Avros Street No.60 Medan, and the Knights of Johor Archery Club which is located at Jl. The work of Darma Gg. Ujung Family, Medan Johor. Therefore a feasibility study was undertaken in establishing an archery sports place in the field. The aspects to be considered in making feasibility studies are market and marketing aspects, technical and equipment aspects, management aspects, legal aspects, economic and social aspects, and financial aspects. Financial analysis using own capital got Payback Period 3 years 5,8 months, Net Present Value Rp 11.684.026 and obtained Internal Rate of Return of 17%.

  10. Technical feasibility of the implantation of a monorail stent system into the renal arteries without pre-dilatation

    International Nuclear Information System (INIS)

    Neumann, C.; Dorffner, R.; Gschwendtner, M.; Karnel, F.; Mair, J.; Dorffner, G.

    2005-01-01

    Purpose: to evaluate the technical feasibility of the implantation of the monorail RX Herculink trademark system into the renal arteries without pre-dilatation. Materials and methods: forty-two patients (mean age 71 years) from four centers with a total of 44 renal artery stenoses underwent implantation of the RX Herculink trademark stent. The mean grade of the stenosis was 83.8%, the mean length 7.5 mm. The stenoses were ostial in 38 cases and in immediate proximity to the ostium in 6 cases. The mean follow-up-period was 57 weeks (24 - 176 weeks). Results: in 42 cases, the implantation was successful without pre-dilatation. In 2 cases, pre-dilatation was carried out. In none of the cases, detachment of the stent from the balloon was observed. In one stenosis with a length of 17 mm, implantation of two stents was performed. In 9 cases, post-dilatation with a larger balloon or higher balloon pressure was necessary. Residual stenoses exceeding 30% were not observed. Two patients developed local bleeding at the puncture site. During the follow-up, restenoses were observed in 5 stents after 26 to 126 weeks, which necessitated a second intervention in 3 cases (PTA in 2 cases, re-stenting in 1 case). The primary patency rate after 6 and 12 months was 0.92 ± 0.056 according to Kaplan-Meier, the secondary patency rate after 6 and 12 months was 1.0 ± 0.0. Conclusion: implantation of the RX Herculink trademark stent system into the renal arteries without pre-dilatation is technically feasible and safe. Even without pre-dilatation, the stent-system can be advanced through the stenosis without detachment. The complication rate is low. Our clinical results are comparable to previous studies. (orig.)

  11. Greater occipital nerve infiltration under MR guidance. Feasibility study and preliminary results

    International Nuclear Information System (INIS)

    Kastler, Adrian; Perolat, Romain; Kastler, Bruno; Maindet-Dominici, Caroline; Fritz, Jan; Benabid, Alim Louis; Chabardes, Stephan; Krainik, Alexandre

    2018-01-01

    To assess the feasibility of greater occipital nerve (GON) intermediate site infiltration with MRI guidance. Eleven consecutive patients suffering from chronic refractory cranio-facial pain who underwent 16 GON infiltrations were included in this prospective study. All of the procedures were performed on an outpatient basis in the research facility of our institution, with a 1.5 T scanner. The fatty space between inferior obliquus and semispinalis muscles at C1-C2 level was defined as the target. Technical success was defined as the ability to accurately inject the products at the target, assessed by post-procedure axial and sagittal proton density-weighted sequences. Clinical success was defined as a 50% pain decrease at 1 month. Technical success was 100%. GON was depicted in 6/11 cases on planning MRI sequences. Mean duration of procedure was 22.5 min (range 16-41). Clinical success was obtained in 7/11 included patients (63.6%) with a mean self-reported improvement of 78%. Interventional MR-guidance for GON infiltration is a feasible technique offering similar results to an already established effective procedure. It may appear as a useful tool in specific populations, such as young patients and repeat infiltrations, and should be considered in these settings. (orig.)

  12. Greater occipital nerve infiltration under MR guidance. Feasibility study and preliminary results

    Energy Technology Data Exchange (ETDEWEB)

    Kastler, Adrian; Perolat, Romain [Grenoble Alpes University Hospital, Neuroradiology and MRI Unit, Grenoble (France); CLINATEC Research Facility, LETI, CEA Grenoble (France); Kastler, Bruno [Paris V University, Adult Radiology Department, Necker Hospital, Paris (France); Maindet-Dominici, Caroline [Grenoble Alpes University Hospital, Pain Management Unit, Grenoble (France); Fritz, Jan [The Johns Hopkins University School of Medicine, Russell H. Morgan Department of Radiology and Radiological Science, Baltimore, MD (United States); Benabid, Alim Louis [CLINATEC Research Facility, LETI, CEA Grenoble (France); Chabardes, Stephan [CLINATEC Research Facility, LETI, CEA Grenoble (France); Grenoble Alpes University Hospital, Neurosurgery Unit, Grenoble (France); Krainik, Alexandre [Grenoble Alpes University Hospital, Neuroradiology and MRI Unit, Grenoble (France)

    2018-02-15

    To assess the feasibility of greater occipital nerve (GON) intermediate site infiltration with MRI guidance. Eleven consecutive patients suffering from chronic refractory cranio-facial pain who underwent 16 GON infiltrations were included in this prospective study. All of the procedures were performed on an outpatient basis in the research facility of our institution, with a 1.5 T scanner. The fatty space between inferior obliquus and semispinalis muscles at C1-C2 level was defined as the target. Technical success was defined as the ability to accurately inject the products at the target, assessed by post-procedure axial and sagittal proton density-weighted sequences. Clinical success was defined as a 50% pain decrease at 1 month. Technical success was 100%. GON was depicted in 6/11 cases on planning MRI sequences. Mean duration of procedure was 22.5 min (range 16-41). Clinical success was obtained in 7/11 included patients (63.6%) with a mean self-reported improvement of 78%. Interventional MR-guidance for GON infiltration is a feasible technique offering similar results to an already established effective procedure. It may appear as a useful tool in specific populations, such as young patients and repeat infiltrations, and should be considered in these settings. (orig.)

  13. An investigation on technical feasibilities of fuel cycle for high temperature gas-cooled reactor (Case study)

    International Nuclear Information System (INIS)

    Sumita, Junya; Ueta, Shohei; Aihara, Jun; Shibata, Taiju; Sawa, Kazuhiro

    2008-03-01

    In accordance with the basic policy of effectively using nuclear fuel resources, the FBR cycle, one of the most possible fuel cycle in the future, will be adapted after plu-thermal program by LWR in Japanese nuclear cycle plan. In this paper, a case study of technical investigation of HTGR fuel cycle based on HTGR fuel cycle proposed to adapt to Japanese nuclear fuel cycle plan were carried out from the viewpoint of effective utilization of uranium, fabrication technologies of MOX fuel, reprocessing technologies, amount of interim storage of HTGR fuel and graphite waste. As a result, the fuel cycle for HTGR is expected to be possible technically. (author)

  14. Feasibility study report for Operable Unit 4: Fernald Environmental Management Project, Fernald, Ohio: Remedial investigation and feasibility study: Volume 3: Final report

    International Nuclear Information System (INIS)

    1994-02-01

    This report documents the Feasibility Study (FS) phase of the Fernald Environmental Management Project (FEMP) Operable Unit 4 Remedial Investigation/Feasibility Study (RI/FS) Program. The FEMP, formerly known as the Feed Materials Production Center (FMPC), is a US Department of Energy (DOE) facility that operated from 1952 to 1989. The facility's primarily function was to provide high purity uranium metal products to support United States defense programs. Production operations were suspended in 1989 to focus on environmental restoration and waste management activities at the facility. The RI/FS is being conducted pursuant to the terms of a Consent Agreement between DOE and the US Environmental Protection Agency (EPA) under Sections 120 and 106(a) of the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA), as amended. The Ohio Environmental Protection Agency (OEPA) is also participating in the RI/FS process at the FEMP through direct involvement in program review meetings and technical review of project documentation. The objective of the RI/FS process is to gather information to support an informed risk management decision regarding which remedy appears to be the most appropriate action for addressing the environmental concerns identified at the FEMP. This volume contains appendices F--J

  15. Novel Multisensor Probe for Monitoring Bladder Temperature During Locoregional Chemohyperthermia for Nonmuscle-Invasive Bladder Cancer: Technical Feasibility Study

    Science.gov (United States)

    Geijsen, Debby E.; Zum Vörde Sive Vörding, Paul J.; Schooneveldt, Gerben; Sijbrands, Jan; Hulshof, Maarten C.; de la Rosette, Jean; de Reijke, Theo M.; Crezee, Hans

    2013-01-01

    Abstract Background and Purpose: The effectiveness of locoregional hyperthermia combined with intravesical instillation of mitomycin C to reduce the risk of recurrence and progression of intermediate- and high-risk nonmuscle-invasive bladder cancer is currently investigated in clinical trials. Clinically effective locoregional hyperthermia delivery necessitates adequate thermal dosimetry; thus, optimal thermometry methods are needed to monitor accurately the temperature distribution throughout the bladder wall. The aim of the study was to evaluate the technical feasibility of a novel intravesical device (multi-sensor probe) developed to monitor the local bladder wall temperatures during loco-regional C-HT. Materials and Methods: A multisensor thermocouple probe was designed for deployment in the human bladder, using special sensors to cover the bladder wall in different directions. The deployment of the thermocouples against the bladder wall was evaluated with visual, endoscopic, and CT imaging in bladder phantoms, porcine models, and human bladders obtained from obduction for bladder volumes and different deployment sizes of the probe. Finally, porcine bladders were embedded in a phantom and subjected to locoregional heating to compare probe temperatures with additional thermometry inside and outside the bladder wall. Results: The 7.5 cm thermocouple probe yielded optimal bladder wall contact, adapting to different bladder volumes. Temperature monitoring was shown to be accurate and representative for the actual bladder wall temperature. Conclusions: Use of this novel multisensor probe could yield a more accurate monitoring of the bladder wall temperature during locoregional chemohyperthermia. PMID:24112045

  16. Case study on the feasibility of small and medium nuclear power plants in Egypt

    International Nuclear Information System (INIS)

    1994-04-01

    The IAEA agreed to co-operate with the Arab Republic of Egypt in performing a case study on the feasibility of small and medium power reactors (SMPRs) as a technical assistance project. The major objective of this study is to examine the feasibility of SMPRs to supply a portion of the future electrical energy requirements in the long term power programme of Egypt. The IAEA is grateful to all who provided information and assisted in the drafting and review of the report, in particular to the Advisory Group which performed the study in a co-operative effort. It is hoped that the report will meet the interests of policy makers, managers, engineers and economists in Member States, particularly in developing countries, and that it will provide a useful basis for specific studies to prepare decisions on SMPR projects. Refs, figs and tabs

  17. Investigation of the potential of wind energy applications in the Sct. Petersburg region. Pre-feasibility study report. Phase 1

    International Nuclear Information System (INIS)

    1995-11-01

    It was proposed to initiate an investigation and, if found to be viable, a feasibility study of the possibilities for partly substituting and supplementing the existing nuclear and fossil fuel based energy supply of the St. Petersburg region with environmentally benign wind energy. The feasibility study is expected to lead to one or more pilot projects. The proposal outlines a three-phased project including an investigation, a feasibility study and a full scale demonstration of wind energy in this region. A 4th phase is envisaged, and this will include the large scale introduction of wind energy applications using national and international financing and resulting in increased local production. The report covers the first phase, the investigation which includes data acquisition and desk studies. It is shown that technically exploitable wind potential exists in the St. Petersburg region, that local production of wind turbine equipment will reduce wind turbine costs due to decreased transport costs and lower local salaries, that suitable sites for the demonstration of both grid-connected wind farms and wind-diesel systems have been preliminarily identified and that the demonstration plants investigated have exhibited reasonable economic parameters - IRR in the range of 9 - 15%. But a feasibility study phase (2) including engineering and economic analyses must be carried out in order to reach the necessary detailed understanding of the technical and economic implications of full scale demonstration projects. (EG)

  18. Low-dose CT colonography in children: initial experience, technical feasibility and utility

    International Nuclear Information System (INIS)

    Anupindi, Sudha; Perumpillichira, James; Zalis, Michael E.; Jaramillo, Diego; Israel, Esther J.

    2005-01-01

    CT colonography (CTC) is utilized as a diagnostic tool in the detection of colon polyps and early colorectal cancer in adults. Large studies in the literature, although focused on adult populations, have shown CTC to be a safe, accurate, non-invasive technique. We evaluated the technical feasibility of CTC in children using a low-dose technique. From November 2001 to April 2004 we evaluated eight patients (3-17 years) with non-contrast CTC. Seven of the patients had CTC, followed by standard colonoscopy (SC) the same day; in one patient, CTC followed a failed SC. CTC results were compared to results of SC. The estimated effective dose from each CTC was calculated and compared to that of standard barium enema. CTC results were consistent with those of SC. Sensitivity for polyps 5-10 mm was 100%, and sensitivity for polyps 10 mm and larger was 66.7%. The estimated mean effective dose was 2.17 mSv for CTC, compared to the 5-6 mSv for a standard air-contrast barium enema in a small child. Our initial experience shows CTC in children is well-tolerated, safe, and useful. The procedure can be performed successfully with a low radiation dose, and preliminary results compare well with SC. (orig.)

  19. Development of new port in Minahasa Utara: A-pre feasibility study

    Science.gov (United States)

    Hamzah, Suharman; Abdurahman, Asad; Saputra, Reza; Aprianti, Evi

    2017-11-01

    In order to support Indonesian Government priority sector to build toll maritime in conjunction to connect "nusantara" as an archipelago country, and also to develop the frontier area of Indonesia, the existence of a port should get more in attention as the gate of Indonesia. A port has significant role in changing of transport mode and at the end as catalyst of economic growth. An important thing from pre-feasibility studies is the priority factor will clearly shown wheather it is good or fair. As a supporting to service passenger moving, container, general cargo and also bulk, a port is necessary to have an excellent design and planning. A pre-feasibility study is required to obtain a scientific basis based on value of interest and the necessity of the region. A pre-feasibility study in this paper aims to identify potential support of the region and giving priority location of development of new port in Minahasa Utara regarding to spatial, government issues, transportation aspect, regional economics, environmental aspect and technical aspect consideration. Experimental Method used are qualitative and quantitative, going through to the data obtained and supported by interview on the spot as well as questionnaire surveys. Result of this paper showing that there are 5 locations suitable with the requirements. Based on the level of priority, high (Kema, Likupang), moderate (Linuhu, Kahuku) and low (Gangga 1).

  20. Dual-Doppler Feasibility Study

    Science.gov (United States)

    Huddleston, Lisa L.

    2012-01-01

    When two or more Doppler weather radar systems are monitoring the same region, the Doppler velocities can be combined to form a three-dimensional (3-D) wind vector field thus providing for a more intuitive analysis of the wind field. A real-time display of the 3-D winds can assist forecasters in predicting the onset of convection and severe weather. The data can also be used to initialize local numerical weather prediction models. Two operational Doppler Radar systems are in the vicinity of Kennedy Space Center (KSC) and Cape Canaveral Air Force Station (CCAFS); these systems are operated by the 45th Space Wing (45 SW) and the National Weather Service Melbourne, Fla. (NWS MLB). Dual-Doppler applications were considered by the 45 SW in choosing the site for the new radar. Accordingly, the 45th Weather Squadron (45 WS), NWS MLB and the National Aeronautics and Space Administration tasked the Applied Meteorology Unit (AMU) to investigate the feasibility of establishing dual-Doppler capability using the two existing systems. This study investigated technical, hardware, and software requirements necessary to enable the establishment of a dual-Doppler capability. Review of the available literature pertaining to the dual-Doppler technique and consultation with experts revealed that the physical locations and resulting beam crossing angles of the 45 SW and NWS MLB radars make them ideally suited for a dual-Doppler capability. The dual-Doppler equations were derived to facilitate complete understanding of dual-Doppler synthesis; to determine the technical information requirements; and to determine the components of wind velocity from the equation of continuity and radial velocity data collected by the two Doppler radars. Analysis confirmed the suitability of the existing systems to provide the desired capability. In addition, it is possible that both 45 SW radar data and Terminal Doppler Weather Radar data from Orlando International Airport could be used to alleviate any

  1. Separating civil and military nuclear programmes in the UK and France; a feasibility study

    International Nuclear Information System (INIS)

    Hart, David

    1987-01-01

    In recent years there has been considerable concern shown by the general public and the trade unions over the connection between the civil and military nuclear programmes. This paper is the result of research to determine the feasibility of separating the two in the UK and France. The result of the study is that it is technically and economically feasible to adopt a policy of separation. The costs are not overwhelming, rather the difficulty lies in assessing the intangible benefits of such a programme, and in overcoming any political impediments to its adoption. The major political fear is that adopting a separation programme would put that nation at a disadvantage with respect to other nuclear weapon states. (author)

  2. Technical and economic feasibility of alternative fuel use in process heaters and small boilers

    Energy Technology Data Exchange (ETDEWEB)

    1980-02-01

    The technical and economic feasibility of using alternate fuels - fuels other than oil and natural gas - in combustors not regulated by the Powerplant and Industrial Fuel Use Act of 1978 (FUA) was evaluated. FUA requires coal or alternate fuel use in most large new boilers and in some existing boilers. Section 747 of FUA authorizes a study of the potential for reduced oil and gas use in combustors not subject to the act: small industrial boilers with capacities less than 100 MMBtu/hr, and process heat applications. Alternative fuel use in combustors not regulated by FUA was examined and the impact of several measures to encourage the substitution of alternative fuels in these combustors was analyzed. The primary processes in which significant fuel savings can be achieved are identified. Since feedstock uses of oil and natural gas are considered raw materials, not fuels, feedstock applications are not examined in this analysis. The combustors evaluated in this study comprise approximately 45% of the fuel demand projected in 1990. These uses would account for more than 3.5 million barrels per day equivalent fuel demand in 1990.

  3. Analysis methodology for economic technical feasibility studies in offshore electrical generation systems; Metodologia de analisis para estudios de factibilidad tecnica economica en sistemas de generacion electrica costa fuera

    Energy Technology Data Exchange (ETDEWEB)

    Fiscal Escalante, Raul [Instituto de Investigaciones Electricas, Cuernavaca, Morelos (Mexico)

    2007-07-01

    An analysis methodology followed in the development of technique-economic feasibility studies of systems of electrical generation in offshore electrical installations is presented, including the obtaining of the curves of the turbine and generator performance, the technical considerations for the formulation of the operation scenes and the calculations of the economic evaluation of a real scenario. [Spanish] Se muestra una metodologia de analisis seguida en el desarrollo de estudios de factibilidad tecnica-economica de sistemas de generacion electrica en instalaciones electricas costa fuera, incluyendo la obtencion de las curvas de comportamiento de la turbina y el generador, las consideraciones tecnicas para la formulacion de los escenarios de operacion y los calculos de la evaluacion economica de un escenario real.

  4. Feasibility study report for Operable Unit 4: Volume 2

    International Nuclear Information System (INIS)

    1994-02-01

    This report documents the Feasibility Study (FS) phase of the Fernald Environmental Management Project (FEMP) Operable Unit 4 Remedial Investigation/Feasibility Study (RI/FS) Program. The FEMP, formerly known as the Feed Materials Production Center (FMPC), is a US Department of Energy (DOE) facility that operated from 1952 to 1989. The facility's primarily function was to provide high purity uranium metal products to support United States defense programs. Production operations were suspended in 1989 to focus on environmental restoration and waste management activities at the facility. The RI/FS is being conducted pursuant to the terms of a Consent Agreement between DOE and the US Environmental Protection Agency (EPA) under Sections 120 and 106(a) of the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA), as amended. The Ohio Environmental Protection Agency (OEPA) is also participating in the RI/FS process at the FEMP through direct involvement in program review meetings and technical review of project documentation. The objective of the RI/FS process is to gather information to support an informed risk management decision regarding which remedy appears to be the most appropriate action for addressing the environmental concerns identified at the FEMP. This volume contains appendices A--E

  5. Stainless Steel RSM Beneficial Reuse technical feasibility to business reality

    International Nuclear Information System (INIS)

    Boettinger, W.L.; Mishra, G.

    1997-08-01

    The Stainless Steel Beneficial Reuse Program began in 1994 as a demonstration funded by the DOE Office of Science and Technology. The purpose was to assess the practicality of stainless steel radioactive scrap metal (RSM) recycle. Technical feasibility has been demonstrated through the production of a number of products made from recycled RSM. A solid business foundation is yet to be achieved. However, a business environment is beginning to develop as multiple markets and applications for RSM are surfacing around the Complex. The criteria for a successful business reality includes: - affordable programs, - a continuing production base from which to expand, - real products needs, -adequate RSM supply, and - a multi-year program This program currently sponsored by SRS and DOE-ORO to fabricate Defense Waste Processing Facility (DWPF) canisters from RSM provides an activity that satisfies these criteria. The program status is discussed. A comparison of the cost of DWPF canisters fabricated from recycled RSM and virgin metal is presented. The comparison is a function of several factors: disposal costs, the fabrication cost of virgin metal canisters, the fabrication cost of recycled RSM canisters, free release decontamination costs, and the cost to accumulate the RSM. These variables are analyzed and the relationship established to show the break-even point for various values of each parameter

  6. Solar feasibility study for site-specific industrial-process-heat applications. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Murray, O.L.

    1980-03-18

    This study addresses the technical feasibility of solar energy in industrial process heat (IPH) applications in Mid-America. The study was one of two contracted efforts covering the MASEC 12-state region comprised of: Illinois, Michigan, North Dakota, Indiana, Minnesota, Ohio, Iowa, Missouri, South Dakota, Kansas, Nebraska, Wisconsin. The results of our study are encouraging to the potential future role of solar energy in supplying process heat to a varied range of industries and applications. We identified and developed Case Study documentation of twenty feasible solar IPH applications covering eight major SIC groups within the Mid-American region. The geographical distribution of these applications for the existing range of solar insolation levels are shown and the characteristics of the applications are summarized. The results of the study include process identification, analysis of process heat requirements, selection of preliminary solar system characteristics, and estimation of system performance and cost. These are included in each of the 20 Case Studies. The body of the report is divided into two primary discussion sections dealing with the Study Methodology employed in the effort and the Follow-On Potential of the identified applications with regard to possible demonstration projects. The 20 applications are rated with respect to their relative overall viability and procedures are discussed for possible demonstration project embarkment. Also, a possible extension of this present feasibility study for late-comer industrial firms expressing interest appears worthy of consideration.

  7. Cogeneration: Key feasibility analysis parameters

    International Nuclear Information System (INIS)

    Coslovi, S.; Zulian, A.

    1992-01-01

    This paper first reviews the essential requirements, in terms of scope, objectives and methods, of technical/economic feasibility analyses applied to cogeneration systems proposed for industrial plants in Italy. Attention is given to the influence on overall feasibility of the following factors: electric power and fuel costs, equipment coefficients of performance, operating schedules, maintenance costs, Italian Government taxes and financial and legal incentives. Through an examination of several feasibility studies that were done on cogeneration proposals relative to different industrial sectors, a sensitivity analysis is performed on the effects of varying the weights of different cost benefit analysis parameters. With the use of statistical analyses, standard deviations are then determined for key analysis parameters, and guidelines are suggested for analysis simplifications

  8. Technical and economic feasibility of thermal storage. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Shelpuk, B.; Joy, P.; Crouthamel, M.

    1977-06-01

    The technical and economic feasibility of various thermal energy storage alternatives is determined by comparing the system performance and annualized cost which result from each storage alternative operating with the same solar collector model, the same building load model, and the same heating system and controls model. Performance and cost calculations are made on the basis of an hour-by-hour time step using actual weather bureau data for Albuquerque, N. M., and New York City for a single six-month heating season. The primary approach to comparing various storage alternatives is to allow the collector area and storage mass to vary until a minimum cost combination is achieved. In the Albuquerque location collector area of 325 ft/sup 2/, water storage mass of 12.5 lb/ft/sup 2/ of collector area, and phase change mass of 6.25 lb/ft/sup 2/ of collector area results in minimum cost systems, each of which delivers about 50% of the total building demand. The primary conclusion is that, using current costs for materials and containers, water is the cheapest storage alternative for heating applications in both Albuquerque and New York City. The cost of containing or encapsulating phase change materials, coupled with their small system performance advantage, is the main reason for this conclusion. The use of desiccant materials for thermal storage is considered to be impractical due to irreversibilities in thermal cycling.

  9. Technical and economic feasibility of superconducting power transmission: a case study

    International Nuclear Information System (INIS)

    Forsyth, E.B.; Mulligan, G.A.; Beck, J.W.; Williams, J.A.

    1975-01-01

    The long-range plans of the Long Island Lighting Company include the installation of 4600 MW of generation capacity at nuclear sites on eastern Long Island by the 1990's. A single site, Shoreham, was chosen for this study which would require transmission facilities to the Ruland Road substation, 43 miles away. Conventional 345 kV overhead and underground circuits are planned for this service. For the case study three superconducting cable schemes have been investigated which reflect various technical options. The superconducting cables have been designed to meet acceptable normal and contingency load flow conditions and to withstand maximum short circuit faults. A cost analysis has been made of the complete installation, providing a valuable comparison of the estimated cost of this new technology with conventional methods. The most favorable cost comparison is a two-circuit 345 kV superconducting system, which appears to be about one-half the cost of an all underground 345 kV high pressure oil-filled cable system. No reactive compensation will be required for the superconducting system, whereas extensive compensation is required for HPOF cables over the same distance. The cost estimate for the two-circuit superconducting system is about twice that of 345 kV overhead transmission, which would consist of two double circuits and one single circuit, assuming right-of-way could be obtained. (U.S.)

  10. Technical and economic feasibility study of low flow compressors; Estudo de viabilidade tecnica e economica de compressores de baixa vazao

    Energy Technology Data Exchange (ETDEWEB)

    Silva, Nagib F. da; Vieira, Francisco A. [Centro de Tecnologias do Gas (CTGAS), Natal, RN (Brazil); Campos, Michel F.; Moura, Newton R. de [PETROBRAS, Rio de Janeiro, RJ (Brazil)

    2004-07-01

    One of the main problems for the installation of new natural gas stations has been the high investment for compressor acquisition. Out of 900 thousand Reais, which is an average value for the construction of a supplying structure, 600 thousand are destined for the acquisition of the compression system (average outflow of 800 Nm{sup 3}/hour at 20 deg C, 1 atm), approach commonly used in Brazil. To be economically feasible, it is necessary that the fueling station has a supplying volume of at least 600 vehicles/day. Niches of NGV market have been identified to new potentials, where the compressed gas demand is lower, therefore not justifying an investment in compression systems of high capacity. A solution for reduction of this investment would be the introduction in the Brazilian market of compression systems of medium and low outflow and with lower cost. In this context, CTGAS has a project into RedeGasEnergia in partnership with PETROBRAS, funded by FINEP/CTPETRO, to develop, to acquire, and to mount prototypes of compression systems of small and medium capacities. To attend the objectives of this project, a compressor was developed in a partnership with a national manufacturer, MOVITEC, and participation of CENPES, with an outflow of 200 Nm{sup 3}/hour (at 20 deg C 1 atm.), for a demand of up to 200 vehicles/day. Another alternative, for the case of small consumers with supplying demand of up to 15 vehicles/day is being made possible by the introduction in the Brazilian market of two compression systems of outflow with up to 13,0 Nm{sup 3}/h (at 20 deg C 1 atm). The installation of these systems will assist in the economical and technical feasibility studies. At this moment, there are some companies interested in knowing this new technology for using the compressor in their installations, thus demonstrating the success of this project, as well as the wakening of a new consuming market. (author)

  11. Preparing a feasibility study for a maglev transport system

    Energy Technology Data Exchange (ETDEWEB)

    Kessel, H

    1984-06-01

    The Transrapid test facility in Emsland is almost completed, and the phase of putting into operation with the TR 06 maglev vehicle has commenced. This will be followed by a general test phase to check the practicability of the maglev system. It is now time to clarify, by means of a feasibility study, what steps are necessary for the introduction of the maglev system in West Germany. Taking two existing railway lines as example, namely Hamburg-Hannover and Duesseldorf Airport-Cologne/Bonn Airport, the effect will be examined of the public-law licensing procedure, participation of the general public in planning procedures, and the information of the media. Also, the technical framework data will be revised on the basis of the experience gained in building the Transrapid facility and the technical improvements made subsequently. Proposed track routing plans are to take particular account of environmental protection considerations, while cost accounting models will be developed which allow fast and reliable forecasts to be made for future projects in respect of investment and operating costs, and optimal operating procedures will be determined by means of simulation.

  12. Slaughterhouse sewage treatment using gamma radiation - economical feasibility study

    International Nuclear Information System (INIS)

    Melo, Rita; Botelho, M. Luisa; Branco, Joaquim

    2005-01-01

    This paper presents preliminary results of a financial viability study for the implementation of gamma radiation technology on a slaughterhouse wastewater treatment industry. Five scenarios were studied, including the current practice, representing different types of treatments and goals, e.g.: water reuse and/or sludge add value as agriculture fertilizers. Cost-benefit analysis, including the net present value (NPV) of each scenario, was used as a technique to compare the relative value of various strategies. Taking in account that the initial investment is amortized after 20 years, the implementation of Co-60 treatment with 20% water reuse and sludge application as agriculture fertilizers represents the most profitable project with the highest NPV. Therefore, the implementation of gamma radiation technology on a slaughterhouse wastewater treatment industry is not only technically viable as well as economically feasible. (author)

  13. Feasibility Study of Solar Photovoltaics on Landfills in Puerto Rico (Second Study)

    Energy Technology Data Exchange (ETDEWEB)

    Salasovich, J.; Mosey, G.

    2011-08-01

    This report presents the results of an assessment of the technical and economic feasibility of deploying a solar photovoltaics (PV) system on landfill sites in Puerto Rico. The purpose of this report is to assess the landfills with the highest potential for possible solar PV installation and estimate cost, performance, and site impacts of three different PV options: crystalline silicon (fixed tilt), crystalline silicon (single-axis tracking), and thin film (fixed tilt). The report outlines financing options that could assist in the implementation of a system. According to the site production calculations, the most cost-effective system in terms of return on investment is the thin-film fixed-tilt technology. The report recommends financing options that could assist in the implementation of such a system. The landfills and sites considered in this report were all determined feasible areas in which to implement solar PV systems.

  14. Feasibility of multi-sector policy measures that create activity-friendly environments for children: results of a Delphi study

    Directory of Open Access Journals (Sweden)

    Aarts Marie-Jeanne

    2011-12-01

    Full Text Available Abstract Background Although multi-sector policy is a promising strategy to create environments that stimulate physical activity among children, little is known about the feasibility of such a multi-sector policy approach. The aims of this study were: to identify a set of tangible (multi-sector policy measures at the local level that address environmental characteristics related to physical activity among children; and to assess the feasibility of these measures, as perceived by local policy makers. Methods In four Dutch municipalities, a Delphi study was conducted among local policy makers of different policy sectors (public health, sports, youth and education, spatial planning/public space, traffic and transportation, and safety. In the first Delphi round, respondents generated a list of possible policy measures addressing three environmental correlates of physical activity among children (social cohesion, accessibility of facilities, and traffic safety. In the second Delphi round, policy makers weighted different feasibility aspects (political feasibility, cultural/community acceptability, technical feasibility, cost feasibility, and legal feasibility and assessed the feasibility of the policy measures derived from the first round. The third Delphi round was aimed at reaching consensus by feedback of group results. Finally, one overall feasibility score was calculated for each policy measure. Results Cultural/community acceptability, political feasibility, and cost feasibility were considered most important feasibility aspects. The Delphi studies yielded 16 feasible policy measures aimed at physical and social environmental correlates of physical activity among children. Less drastic policy measures were considered more feasible, whereas environmental policy measures were considered less feasible. Conclusions This study showed that the Delphi technique can be a useful tool in reaching consensus about feasible multi-sector policy measures. The

  15. Role of decision-tree analysis in the performance of a complex feasibility study

    International Nuclear Information System (INIS)

    Dworkin, D.; Sarkar, A.; Motwani, J.

    1991-01-01

    This report presents the results of the Feasibility Study (FS) of a National Priorities List (NPL) site in New Jersey and the decision tree that made this FS possible. The development of the decision tree and the remedial action alternatives that address the hazards at the site are presented. The FS efforts were performed in accordance with U.S. EPA guidance under the authority of the Comprehensive Environmental Response, Compensation, and Liability Act of 1980 (CERCLA) as amended by the Superfund Amendments and Reauthorization Act of 1986 (SARA). A Record of Decision (ROD) is expected in mid-1990. The subject site, the Myers Property site in Franklin Township, New Jersey, has been owned by several individuals and companies since 1811. Uses have included the production of DDT. A Remedial Investigation (RI) was performed by WESTON, the lead technical firm for this feasibility study, which identified soils/sediments, groundwater and buildings on the site as areas of concern. The major chemicals of concern are DDT and its metabolites, polynuclear aromatic compounds, various chlorinated benzenes, dioxin/furan homologues and heavy metals such as arsenic, cadmium, copper, lead, chromium and nickel. While this FS was developed in accordance with current CERCLA FS guidance and procedures, it was expanded to accommodate several outstanding technical and policy issues. Outstanding technical issues focused on uncertainties with respect to hydrogeologic conditions, and policy issues centered upon the development of the site-specific remedial action goals. A decision tree was established to facilitate the development of remedial strategies. The decision tree formed the basis for the FS and allowed remedial alternatives to be identified and evaluated based on key policy decisions. Site media were addressed as contaminated soils/sediments, groundwater and the on-site buildings

  16. Response to 'Burden of proof: A comprehensive review of the feasibility of 100% renewable-electricity systems'

    DEFF Research Database (Denmark)

    Brown, Tom; Bischof-Niemz, Tobias; Breyer, Christian

    2018-01-01

    A recent article 'Burden of proof: A comprehensive review of the feasibility of 100% renewable-electricity systems' claims that many studies of 100% renewable electricity systems do not demonstrate sufficient technical feasibility, according to the criteria of the article's authors (henceforth 'the...... authors'). Here we analyse the authors' methodology and find it problematic. The feasibility criteria chosen by the authors are important, but are also easily addressed at low economic cost, while not affecting the main conclusions of the reviewed studies and certainly not affecting their technical...... feasibility. A more thorough review reveals that all of the issues have already been addressed in the engineering and modelling literature. Nuclear power, as advocated by some of the authors, faces other, genuine feasibility problems, such as the finiteness of uranium resources and a reliance on unproven...

  17. Report on the feasibility study for improving electric motor service centers in Ghana

    Energy Technology Data Exchange (ETDEWEB)

    Hsu, J.S.; Jallouk, P.A.; Staunton, R.H.

    1999-12-10

    On March 3 and 4, 1998, a visit was made to Oak Ridge National Laboratory (ORNL) by two officials from Ghana: Mr. I.K. Mintah, Acting Executive Director, Technical Wing, Ministry of Mines and Energy (MOME) and Dr. A.K. Ofosu-Ahenkorah, Coordinator, Energy Efficiency and Conservation Program, MOME. As a result of this visit, Dr. John S. Hsu of ORNL was invited by MOME to visit the Republic of Ghana in order to study the feasibility of improving electric motor service centers in Ghana.

  18. Multnomah County Hydrokinetic Feasibility Study: Final Feasibility Study Report

    Energy Technology Data Exchange (ETDEWEB)

    Spain, Stephen

    2012-03-15

    HDR has completed a study of the technical, regulatory, and economic feasibility of installing hydrokinetic turbines under the Morrison, Broadway, and Sellwood bridges. The primary objective of installing hydrokinetic turbines is a demonstration of in-stream hydrokinetic technologies for public education and outreach. Due to the low gradient of the Lower Willamette and the effects of the tide, velocities in the area in consideration are simply not high enough to economically support a commercial installation. While the velocities in the river may at times provide enough energy for a commercial turbine to reach capacity, the frequency and duration of high flow events which provide suitable velocities is not sufficient to support a commercial hydrokinetic installation. We have observed that over an 11 year period, daily average velocities in the Lower Willamette exceeded a nominal cut-in speed of 0.75 m/s only 20% of the time, leaving net zero power production for the remaining 80% of days. The Sellwood Bridge site was estimated to have the best hydrokinetic resource, with an estimated average annual production of about 9,000 kWh. The estimated production could range from 2,500 kWh to 15,000 kWh. Based on these energy estimates, the amount of revenue generated through either a power purchase agreement (PPA) or recovered through net metering is not sufficient to repay the project costs within the life of the turbine. The hydrokinetic resource at the Morrison and Broadway Bridges is slightly smaller than at the Sellwood Bridge. While the Broadway and Morrison Bridges have existing infrastructure that could be utilized, the project is not expected to generate enough revenue to repay the investment. Despite low velocities and energy production, the sites themselves are favorable for installation of a demonstration or experimental project. With high public interest in renewable energy, the possibility exists to develop a hydrokinetic test site which could provide

  19. Technical feasibility of a concept radioactive waste disposal facility in Boom clay in the Netherlands

    International Nuclear Information System (INIS)

    Vardon, P.J.; Hicks, M.A.; Fokker, P.A.; Fokkens, J.H.

    2012-01-01

    Document available in extended abstract form only. The current management strategy in the Netherlands for radioactive waste is interim storage for approximately 100 years, followed by final deep geological disposal. At present, both Boom Clay and Salt formations are being considered and investigated via the OPERA (Onderzoeks Programma Eindberging Radioactief Afval) and CORA (Commissie Opberging Radioactief Afval) research programmes respectively, instigated by COVRA (Centrale Organisatie Voor Radioactief Afval). This paper outlines the on-going investigation into the initial technical feasibility of a high-level radioactive waste disposal facility, located within a stratum of Boom Clay, as part of the OPERA research programme. The feasibility study is based on the current Belgian Super-container concept, incorporating specific features relevant to the Netherlands, including the waste inventory and possible future glaciation. The repository is designed to be situated at approximately 500 m depth in a Boom Clay stratum of approximately 100 m thickness, and will co-host vitrified High Level Waste (HLW), spent fuel from research reactors, non-heat generating HLW, Low and Intermediate Level Waste (LILW) and depleted uranium. The total footprint is designed to be 3050 m by 1300 m, and will be segregated by waste type. The waste will be stored in drifts drilled perpendicular to the main galleries and will vary in length and diameter depending upon waste type. The repository life-cycle can be considered in three phases: (i) the pre-operation phase, including the conceptual development, site investigation and selection, design and construction; (ii) the operational phase, including waste emplacement and any period of time prior to closure; and (iii) the post-operational phase. The research on the technical feasibility of the repository will investigate whether the repository can be constructed and whether it is able to perform the appropriate safety functions and meet

  20. Feasibility study of a refrigeration system powered by natural gas; Estudo de viabilidade de um sistema de refrigeracao acionado a gas natural

    Energy Technology Data Exchange (ETDEWEB)

    Costa Filho, Manoel Antonio da Fonseca [Universidade do Estado do Rio de Janeiro (UERJ), RJ (Brazil). Faculdade de Engenharia; Biruel Filho, Jose [PETROBRAS, Rio de Janeiro, RJ (Brazil). Centro de Pesquisas (CENPES)

    2008-07-01

    This paper presents a technical, financial and environmental feasibility study, and market analysis, of a 50-TR chiller with vapor compression (mechanical) cycle powered by internal combustion engine. This type of equipment allows natural gas usage for medium-and-low-capacity refrigeration applications, for which there are not competitive commercial equipment based on absorption refrigeration cycle. The technical feasibility is not questionable because it is the association of two remarkably mature technologies and also because such equipment are common in Europe and USA. The natural gas powered equipment operation costs are lower than electricity powered ones, due to lower energy cost, while acquisition, installation and maintenance costs show the opposite. The Net Present Value is positive. The financial feasibility depends directly on the combination of prices of natural gas and electricity, as well as equipment energy efficiencies. The environmental analysis points to the use of electric-driven equipment, which avoids urban area emissions, reinforced by the hydroelectric generation, renewable, used in Brazil. This study had financial support from PETROBRAS/RedeGasEnergia. (author)

  1. Exoskeleton for Soldier Enhancement Systems Feasibility Study

    Energy Technology Data Exchange (ETDEWEB)

    Jansen, J.F.

    2000-09-28

    The development of a successful exoskeleton for human performance augmentation (EHPA) will require a multi-disciplinary systems approach based upon sound biomechanics, power generation and actuation systems, controls technology, and operator interfaces. The ability to integrate key components into a system that enhances performance without impeding operator mobility is essential. The purpose of this study and report are to address the issue of feasibility of building a fieldable EHPA. Previous efforts, while demonstrating progress and enhancing knowledge, have not approached the level required for a fully functional, fieldable system. It is doubtless that the technologies required for a successful exoskeleton have advanced, and some of them significantly. The question to be addressed in this report is have they advanced to the point of making a system feasible in the next three to five years? In this study, the key technologies required to successfully build an exoskeleton have been examined. The primary focus has been on the key technologies of power sources, actuators, and controls. Power sources, including internal combustion engines, fuel cells, batteries, super capacitors, and hybrid sources have been investigated and compared with respect to the exoskeleton application. Both conventional and non-conventional actuator technologies that could impact EHPA have been assessed. In addition to the current state of the art of actuators, the potential for near-term improvements using non-conventional actuators has also been addressed. Controls strategies, and their implication to the design approach, and the exoskeleton to soldier interface have also been investigated. In addition to these key subsystems and technologies, this report addresses technical concepts and issues relating to an integrated design. A recommended approach, based on the results of the study is also presented.

  2. Early assessment of feasibility and technical specificities of transoral robotic surgery using the da Vinci Xi.

    Science.gov (United States)

    Gorphe, Philippe; Von Tan, Jean; El Bedoui, Sophie; Hartl, Dana M; Auperin, Anne; Qassemyar, Quentin; Moya-Plana, Antoine; Janot, François; Julieron, Morbize; Temam, Stephane

    2017-12-01

    The latest generation Da Vinci ® Xi™ Surgical System Robot released has not been evaluated to date in transoral surgery for head and neck cancers. We report here the 1-year results of a non-randomized phase II multicentric prospective trial aimed at assessing its feasibility and technical specificities. Our primary objective was to evaluate the feasibility of transoral robotic surgery using the da Vinci ® Xi™ Surgical System Robot. The secondary objective was to assess peroperative outcomes. Twenty-seven patients, mean age 62.7 years, were included between May 2015 and June 2016 with tumors affecting the following sites: oropharynx (n = 21), larynx (n = 4), hypopharynx (n = 1), parapharyngeal space (n = 1). Eighteen patients were included for primary treatment, three for a local recurrence, and six for cancer in a previously irradiated field. Three were reconstructed with a FAMM flap and 6 with a free ALT flap. The mean docking time was 12 min. "Chopsticking" of surgical instruments was very rare. During hospitalization following surgery, 3 patients experienced significant bleeding between day 8 and 9 that required surgical transoral hemostasis (n = 1) or endovascular embolization (n = 2). Transoral robotic surgery using the da Vinci ® Xi™ Surgical System Robot proved feasible with technological improvements compared to previous generation surgical system robots and with a similar postoperative course. Further technological progress is expected to be of significant benefit to the patients.

  3. Recent progress in the feasibility study for the first nuclear power plant in Indonesia

    International Nuclear Information System (INIS)

    Adiwardojo

    1997-01-01

    The energy consumption in Indonesia has been continually increasing since 1970 at an average rate of ∼ 10.6%/year. Specifically, for the island of Java, which consumes ∼ 80% of Indonesia's electricity, the installed capacity by PLN was 6363MW in 1990/91. This has increased by ∼ 17%/year during the past three years. Additional increase in electrical consumption of the Java-Bali system projects the need for the installed capacity to reach 31,845 MW in 2003/04. In anticipation of this major addition of installed capacity, the government of Indonesia is conducting feasibility studies of the nuclear option as a means of filling the projected deficit or gap where other fuel options are likely to reach their limits. This paper describes the scope of the present feasibility study including energy economics and financing, technical and safety aspects, the fuel cycle and waste management, general management, and site and environmental studies. (author). 4 refs, 1 fig., 4 tabs

  4. Feasibility of space disposal of radioactive nuclear waste. 2: Technical summary

    Science.gov (United States)

    1974-01-01

    The feasibility of transporting radioactive waste produced in the process of generating electricity in nuclear powerplants into space for ultimate disposal was investigated at the request of the AEC as a NASA in-house effort. The investigation is part of a broad AEC study of methods for long-term storage or disposal of radioactive waste. The results of the study indicate that transporting specific radioactive wastes, particularly the actinides with very long half-lives, into space using the space shuttle/tug as the launch system, appears feasible from the engineering and safety viewpoints. The space transportation costs for ejecting the actinides out of the solar system would represent less than a 5-percent increase in the average consumer's electric bill.

  5. Technical and economic feasibility study of a Frond type wave power generator

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2003-07-01

    This report describes the first stage of the development of a Frond type wave generator by the Engineering Business (EB) in collaboration with the University of Lancaster Engineering Department. The EB Frond concept is a sea-bed reacting, surging machine consisting of a near-surface collector mounted on an arm pivoted near the seabed. The study had six main elements (investigation, physical and mathematical modelling, site characterisation, design review and cost study). The investigation phase involved a study of wave properties and behaviour, while physical models were tested in a wave tank. A mathematical model was developed and used to assess the design's power output. The characteristics of a suitable site for EB Frond generators were determined and the process of identifying possible sites for a demonstrator machine was begun. The mechanical and system arrangement of the design were evaluated and modified. The effects of varying the installation's input parameters (e.g. wave environment factors) were examined using an energy cost model whose output is energy production and cost. It was concluded that the Frond principle was technically viable though there were some remaining engineering and other application problems. Cost modelling suggested that the EB Frond system had potential for long-term commercial prospects. The report recommends the construction and testing of an intermediate scale model with more realistic wave conditions.

  6. Feasibility study of a Green Power Plant. Final report. [Offshore pumped hydro storage

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2013-03-15

    This project is a technical evaluation and a feasibility study of a concept called the Green Power Plant (GPP), developed by Seahorn Energy Aps. The Green Power Plant is an offshore pumped hydro storage facility constructed from prefabricated elements and with integrated renewable energy production. Pumped hydro storage is a known technology with a proven roundtrip energy storage efficiency of 80%. The focus of the GPP project is on simplifying and industrializing the construction of the reservoir wall, thereby achieving a cost efficient solution. The reservoir structure is dependent on the site on which the reservoir is established, thus Kriegers Flak in the Baltic Sea has been chosen as basis for the technical evaluation. As soil conditions vary, the technical evaluations have been based on a general soil profile. A water depth of 25m has been chosen as basis for the evaluation. A reservoir with a diameter of 2 km has been evaluated as baseline scenario. Feasibility of the GPP was evaluated based on the cost and income estimates. For the baseline scenario an internal rate of return of 6.6% was found for a period of 35 years. A sensitivity analysis reveals internal rates of return over 35 years varying from 4.9% to 10.9%. Especially larger reservoir diameters increase profitability of the GPP. The results from this project will be utilized in raising funds for further development of the GPP concept. Seahorn Energy Aps aims at optimizing the wind turbine integration, the steel pile wall structure and the pump-turbine integration in a future project towards construction of a demonstration facility. (LN)

  7. A feasibility study for a manufacturing technology deployment center

    Energy Technology Data Exchange (ETDEWEB)

    1994-10-31

    The Automation & Robotics Research Institute (ARRI) and the Texas Engineering Extension Service (TEEX) were funded by the U.S. Department of Energy to determine the feasibility of a regional industrial technology institute to be located at the Superconducting Super Collider (SSC) Central Facility in Waxahachie, Texas. In response to this opportunity, ARRI and TEEX teamed with the DOE Kansas City Plant (managed by Allied Signal, Inc.), Los Alamos National Laboratory (managed by the University of California), Vought Aircraft Company, National Center for Manufacturing Sciences (NCMS), SSC Laboratory, KPMG Peat Marwick, Dallas County Community College, Navarro Community College, Texas Department of Commerce (TDOC), Texas Manufacturing Assistance Center (TMAC), Oklahoma Center for the Advancement of Science and Technology, Arkansas Science and Technology Authority, Louisiana Productivity Center, and the NASA Mid-Continent Technology Transfer Center (MCTTC) to develop a series of options, perform the feasibility analysis and secure industrial reviews of the selected concepts. The final report for this study is presented in three sections: Executive Summary, Business Plan, and Technical Plan. The results from the analysis of the proposed concept support the recommendation of creating a regional technology alliance formed by the states of Texas, New Mexico, Oklahoma, Arkansas and Louisiana through the conversion of the SSC Central facility into a Manufacturing Technology Deployment Center (MTDC).

  8. Technical and financial feasibility of an inferior vena cava filter retrieval program at a level one trauma center.

    Science.gov (United States)

    Charlton-Ouw, Kristofer M; Leake, Samuel S; Sola, Cristina N; Sandhu, Harleen K; Albarado, Rondel; Holcomb, John B; Miller, Charles C; Safi, Hazim J; Azizzadeh, Ali

    2015-01-01

    Considering new guidelines for retrievable inferior vena cava filters (IVCFs), we examine our initial experience after establishing a comprehensive filter removal program in our level 1 trauma center. We evaluated the technical and financial feasibility of this program and barriers to IVCF retrieval, including insurance status and costs, in trauma patients. Trauma patients receiving IVCFs from May 2011 to 2013 were consented and prospectively enrolled in the study program. Retrieval rates were assessed for the years before study initiation. Primary outcome was IVCF retrieval. Hospital financial data for retrieval were examined and univariate analysis performed. Hospital cost-to-charge and payment-to-charge ratios were assessed. Before study initiation from April 2009 to 2011, 66 IVCFs were placed in trauma patients with only 2 retrievals in 2 years. During the study period, 247 trauma patients had IVCF placement of which 111 (45%) were enrolled. The main reason for nonenrollment was lack of referral by the implanting team. Retrieval was attempted in 100 outpatients with success in 85 (85%). Patients enrolled in the program were more likely to have their filters removed (73% vs. 18%; odds ratio, 12.6; 95% confidence interval, 6.6-24.3; P financially feasible without loss to the health care system even in regions with high rates of uninsured. A major barrier to successful filter retrieval was lack of patient referral into the program by implanting physicians. Hospital administration and physician outreach are important determinants of successful IVCF retrieval in trauma patients. Published by Elsevier Inc.

  9. Automated localization of the prostate at the time of treatment using implanted radiopaque markers: technical feasibility

    International Nuclear Information System (INIS)

    Balter, James M.; Kwok, L. Lam; Sandler, Howard M.; Littles, J. Fred; Bree, Robert L.; Ten Haken, Randall K.

    1995-01-01

    Purpose: Prostate movement is a major consideration in the formation of target volumes for conformal radiation therapy of prostate cancer. The goal of this study was to determine the technical feasibility of using implanted radiopaque markers and digital imaging to localize the prostate at the time of treatment, thus allowing for reduction of the margin required for uncertainty in target position. Methods and Materials: Radiopaque markers implanted around the prostate prior to treatment are visible on electronic radiographs generated with a portal imager or diagnostic imaging device. The locations of the images of these markers on the digital radiographs were automatically determined by a template-matching algorithm. The coordinates of the markers were found by projecting rays through the marker locations on orthogonal radiographs using a three-dimensional (3D) point-matching algorithm. Prostate and/or patient movement was inferred from the marker displacements. Images generated from known movements of a phantom with implanted markers were tested with this algorithm. Locations of markers from daily images of patients with implanted markers were determined by both manual and automatic techniques to determine the efficacy of automated localization on typical clinical images. Results: Prostate movements can be automatically detected in a phantom using low-energy photons within 30 s after image acquisition and with a precision of better than 1 mm in translation and 1 deg. in rotation (indistinguishable from the uncertainty in measuring precision). Conclusion: The studies show that on-line repositioning of the patient based on localization of the markers at the time of treatment is feasible, and may reduce the uncertainty in prostate location when combined with practical on-line repositioning techniques

  10. Study of technical and economic feasibility of a cogeneration system in the tertiary sector; Estudo de viabilidade tecnica-economica de um sistema de cogeracao no setor terciario

    Energy Technology Data Exchange (ETDEWEB)

    Souza, Rodolffo Aquino de; Rocha, Carlos Roberto; Bortoni, Edson da Costa [Universidade Federal de Itajuba (EXCEN/UNIFEI), MG (Brazil). Centro de Excelencia em Eficiencia Energetica

    2008-07-01

    This study aims to examine the technical feasibility and financial cost for a cogeneration system in a company in the tertiary sector. For this, was studied the electromechanical and thermal characteristics of a shopping center, as well as the technologies associated with the proposed cogeneration system. From the modeling of electric and thermal loads it was determined the system of operation for the system and the possible surplus energy generated. For the analysis of economic viability compare operating costs without cogeneration and with the alternative of cogeneration chosen. Among the calculations are the costs of investment and operation of the system. Was encountered the attractiveness of a cogeneration system, which uses natural gas as fuel for alternative engines and, in turn, reject heat to the absorption chillers. The idealized cogeneration system was also evaluated positively with a view to qualification required for participation in policies to encourage the rational use of energy resources. (author)

  11. Southern cone energy network coal gasification for SNG production and pipeline system. Feasibility study. Volume 1. Executive summary. Export trade information

    International Nuclear Information System (INIS)

    1992-01-01

    The Executive Summary document summarizes the study report on the economic and technical feasibility of gasifying coal to produce a substitute natural gas (SNG) for distribution to the industrial areas of Southern Brazil. The report includes data surveys, technology assessments, process evaluations, and conceptual designs and analyses. The study contributes to the Brazilian Government efforts to investigate feasible crude oil substitution programs that will meet the nation's energy needs by utilizing domestic resources, thereby reducing the severe negative impact of foreign crude oil importation on Brazil's balance of payments

  12. Feasibility Study of Non-Destructive Techniques to Measure Corrosion in SAVY Containers

    Energy Technology Data Exchange (ETDEWEB)

    Davenport, Matthew Nicholas [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2016-07-15

    Stainless Steel SAVY containers are used to transport and store nuclear material. They are prone to interior corrosion in the presence of certain chemicals and a low-oxygen environment. SAVY containers also have relatively thin walls to reduce their weight, making their structural integrity more vulnerable to the effects of corrosion. A nondestructive evaluation system that finds and monitors corrosion within containers in use would improve safety conditions and preclude hazards. Non-destructive testing can determine whether oxidation or corrosion is occurring inside the SAVY containers, and there are a variety of non-destructive testing methods that may be viable. The feasibility study described will objectively decide which method best fits the requirements of the facility and the problem. To improve efficiency, the containers cannot be opened during the non-destructive examination. The chosen technique should also be user-friendly and relatively quick to apply. It must also meet facility requirements regarding wireless technology and maintenance. A feasibility study is an objective search for a new technology or product to solve a particular problem. First, the design, technical, and facility feasibility requirements are chosen and ranked in order of importance. Then each technology considered is given a score based upon a standard ranking system. The technology with the highest total score is deemed the best fit for a certain application.

  13. Pinellas Plant feasibility study. Final report

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-09-01

    The Pinellas Plant was built in 1956 to manufacture neutron generators, a principal component in nuclear weapons. In September 1990, the Department of Health and Rehabilitative Services (HRS) entered into an agreement with DOE to independently examine environmental monitoring data from the plant and health data from Pinellas County to determine if an epidemiological study is technically feasible to measure possible off-site health effects from ionizing radiation. Through normal plant operations, some radioactive materials have been released to the environment. Eighty percent of the total plant releases of 107,707 curies occurred in the early years of plant operation (1957--1960). The primary materials released were tritium gas, tritium oxide and krypton-85. Environmental monitoring for radioactive releases from the plant has been done regularly since 1975. The US Public Health Service Centers for Disease Control and Prevention (CDC), in assisting HRS, has determined that sufficient radiological data exist by which a dose reconstruction can be done. A dose reconstruction can provide an estimate of how much radiological exposure someone living in the vicinity of the Pinellas Plant may have suffered from environmental releases.

  14. Pinellas Plant feasibility study. Final report

    International Nuclear Information System (INIS)

    1994-09-01

    The Pinellas Plant was built in 1956 to manufacture neutron generators, a principal component in nuclear weapons. In September 1990, the Department of Health and Rehabilitative Services (HRS) entered into an agreement with DOE to independently examine environmental monitoring data from the plant and health data from Pinellas County to determine if an epidemiological study is technically feasible to measure possible off-site health effects from ionizing radiation. Through normal plant operations, some radioactive materials have been released to the environment. Eighty percent of the total plant releases of 107,707 curies occurred in the early years of plant operation (1957--1960). The primary materials released were tritium gas, tritium oxide and krypton-85. Environmental monitoring for radioactive releases from the plant has been done regularly since 1975. The US Public Health Service Centers for Disease Control and Prevention (CDC), in assisting HRS, has determined that sufficient radiological data exist by which a dose reconstruction can be done. A dose reconstruction can provide an estimate of how much radiological exposure someone living in the vicinity of the Pinellas Plant may have suffered from environmental releases

  15. Aleutian Pribilof Islands Wind Energy Feasibility Study

    Energy Technology Data Exchange (ETDEWEB)

    Bruce A. Wright

    2012-03-27

    Under this project, the Aleutian Pribilof Islands Association (APIA) conducted wind feasibility studies for Adak, False Pass, Nikolski, Sand Point and St. George. The DOE funds were also be used to continue APIA's role as project coordinator, to expand the communication network quality between all participants and with other wind interest groups in the state and to provide continued education and training opportunities for regional participants. This DOE project began 09/01/2005. We completed the economic and technical feasibility studies for Adak. These were funded by the Alaska Energy Authority. Both wind and hydro appear to be viable renewable energy options for Adak. In False Pass the wind resource is generally good but the site has high turbulence. This would require special care with turbine selection and operations. False Pass may be more suitable for a tidal project. APIA is funded to complete a False Pass tidal feasibility study in 2012. Nikolski has superb potential for wind power development with Class 7 wind power density, moderate wind shear, bi-directional winds and low turbulence. APIA secured nearly $1M from the United States Department of Agriculture Rural Utilities Service Assistance to Rural Communities with Extremely High Energy Costs to install a 65kW wind turbine. The measured average power density and wind speed at Sand Point measured at 20m (66ft), are 424 W/m2 and 6.7 m/s (14.9 mph) respectively. Two 500kW Vestas turbines were installed and when fully integrated in 2012 are expected to provide a cost effective and clean source of electricity, reduce overall diesel fuel consumption estimated at 130,000 gallons/year and decrease air emissions associated with the consumption of diesel fuel. St. George Island has a Class 7 wind resource, which is superior for wind power development. The current strategy, led by Alaska Energy Authority, is to upgrade the St. George electrical distribution system and power plant. Avian studies in Nikolski

  16. Feasibility study on floating nuclear power station

    International Nuclear Information System (INIS)

    Kajima, Ryoichi

    1987-01-01

    It is stipulated that nuclear power plants are to be built on solid rock bases on land in Japan. However, there are a limited number of appropriate siting grounds. The Central Research Institute of Electric Power Industry has engaged since 1981 in the studies on the construction technology of power plants, aiming at establishing new siting technology to expand the possible siting areas for nuclear power plants. Underground siting is regarded as a proven technology due to the experience in underground hydroelectric power plants. The technology of siting on quaternary ground is now at the stage of verification. In this report, the outline of floating type offshore/inshore siting technology is introduced, which is considered to be feasible in view of the technical and economical aspects. Three fixed structure types were selected, of which the foundations are fixed to seabed, plant superstructures are above sea surface, and which are floating type. Aiming at ensuring the aseismatic stability of the plant foundations, the construction technology is studied, and the structural concept omitting buoyancy is possible. The most practical water depth is not more than 20 m. The overall plant design, earthquake isolation effect and breakwater are described. (Kako, I.)

  17. Technical and economic study of a mobile system for extraction of eucalyptus essential oil

    Directory of Open Access Journals (Sweden)

    Gisele Aparecida Vivan

    2011-03-01

    Full Text Available The production of essential oils has become increasing in Brazil, especially considering the benefits that certain substances can add to health and range of cosmetics, toiletries and drugs that originate in its processing. Based on these conditions and in the vast area of the Rio Grande do Sul where it is being implanted the culture of eucalyptus, this study seeks ways to boost the economic structure of culture, seeking to generate new business opportunities through the extraction of oil contained in the leaves Eucalyptus, a byproduct of the paper industry, the current main economic interest of culture. Based on these assumptions, it was elaborated a conceptual design of a mobile equipment able to meet the processing demand of the crop, determining a diagram processing flow and fitting the equipment to meet this demand. Subsequently, it was evaluated the technical and economic feasibility of deploying the mobile extraction system for essential oil of eucalyptus in the southern region of Rio Grande do Sul, conducting technical studies for the improvement and efficiency of the conceptual design and economic feasibility analysis to determine variables that determine the success of the project. It was conclude that the conceptual design has beneficial aspects, especially regarding the mobility, flexibility of use, minimization of empty spaces and water use in semi-closed circuit. In the analysis of economic feasibility, the simulated scenarios showed positive values for Net Present Value, Internal Rate of Return above the minimum rate of attractiveness and capital Payback relatively short, even for the scenarios considered critical.

  18. Image-guided spinal injection procedures in open high-field MRI with vertical field orientation: feasibility and technical features

    Energy Technology Data Exchange (ETDEWEB)

    Streitparth, F.; Walter, T.; Wonneberger, U.; Wagner, M.; Hermann, K.G.; Hamm, B.; Teichgraeber, U. [Charite, Humboldt-Universitaet zu Berlin, Department of Radiology, Berlin (Germany); Chopra, S. [Charite-Universitaetsmedizin Berlin, Campus Virchow Klinikum, Department of General, Visceral, and Transplantation Surgery, Berlin (Germany); Wichlas, F. [Charite-Universitaetsmedizin Berlin, Campus Virchow Klinikum, Center for Musculoskeletal Surgery, Berlin (Germany)

    2010-02-15

    We prospectively evaluated the feasibility and technical features of MR-guided lumbosacral injection procedures in open high-field MRI at 1.0 T. In a CuSO{sub 4}.5H{sub 2}O phantom and five human cadaveric spines, fluoroscopy sequences (proton-density-weighted turbo spin-echo (PDw TSE), T1w TSE, T2w TSE; balanced steady-state free precession (bSSFP), T1w gradient echo (GE), T2w GE) were evaluated using two MRI-compatible 20-G Chiba-type needles. Artefacts were analysed by varying needle orientation to B{sub 0}, frequency-encoding direction and slice orientation. Image quality was described using the contrast-to-noise ratio (CNR). Subsequently, a total of 183 MR-guided nerve root (107), facet (53) and sacroiliac joint (23) injections were performed in 53 patients. In vitro, PDw TSE sequence yielded the best needle-tissue contrasts (CNR = 45, 18, 15, 9, and 8 for needle vs. fat, muscle, root, bone and sclerosis, respectively) and optimal artefact sizes (width and tip shift less than 5 mm). In vivo, PDw TSE sequence was sufficient in all cases. The acquisition time of 2 s facilitated near-real-time MRI guidance. Drug delivery was technically successful in 100% (107/107), 87% (46/53) and 87% (20/23) of nerve root, facet and sacroiliac joint injections, respectively. No major complications occurred. The mean procedure time was 29 min (range 19-67 min). MR-guided spinal injections in open high-field MRI are feasible and accurate using fast TSE sequence designs. (orig.)

  19. Cherokee Wind Energy Development - Feasibility and Pre-Construction Studies

    Energy Technology Data Exchange (ETDEWEB)

    McMillan, Andy [Cherokee Nation Businesses, LLC, Catoosa, OK (United States)

    2017-06-30

    Cherokee Nation Businesses (CNB) received a grant from the US Department of Energy to explore feasibility and pursue development of a wind power generation facility on Cherokee land in north-central Oklahoma. This project followed several years of initial study exploring the possibility of commercial-scale wind power generation on primarily agricultural land owned by the Cherokee Nation. This project produced detailed analysis of the legal, financial and market viability of such generation facilities, and encompassed a full technical evaluation of the engineering, environmental, and geotechnical aspects of installing this capacity. During the course of this project, information gleaned from this exploration changed CNB’s thinking about the best course of action for Cherokee participation in the development, eventually moving away from an equity-owner model and towards utilization of the land asset as a resource while mitigating Cherokee financial and operational risk.

  20. Technical Feasibility and Oncological Legitimacy of Enucleation of Intraductal Papillary Mucinous Neoplasm Located at the Pancreatic Head or Uncinate Process.

    Science.gov (United States)

    Soejima, Yuji; Toshima, Takeo; Motomura, Takashi; Yokota, Tomoyuki; Joko, Kouji; Oshiro, Yumi; Takahashi, Ikuo; Nishizaki, Takashi; Maehara, Yoshihiko

    2017-01-01

    Surgical indications and strategies for branch duct (BD)-intraductal papillary mucinous neoplasm (IPMN) at the pancreatic head (PH) are controversial issues. We investigated the technical feasibility and oncological legitimacy of enucleation for IPMN of the PH. The clinicopathological parameters of 11 patients with IPMN who underwent conventional pancreaticoduodenectomy (PD, n=7) or enucleation (n=4) during the same period were evaluated. The mean operative time (442 vs. 280 min, p<0.05) and blood loss (864 vs. 93 ml, p<0.05) were significantly better in the enucleation group. The final pathological diagnosis (low-/intermediate-/high-grade dysplasia) in the PD and enucleation groups was 4/2/1 and 3/1/0, respectively. The incidence of grade B pancreatic fistula and Clavien III complications was 14% vs. 0% and 43% vs. 25%, respectively. No recurrent pancreatitis or exocrine or endocrine dysfunction was noted in the enucleation group; however, de novo or exacerbated diabetes mellitus developed in three patients in the PD group. All patients were alive and no disease recurrence was noted at a mean follow-up of 1,059 days. Enucleation of BD-IPMN at the PH is a technically feasible and oncologically acceptable procedure which should be justified in patients with IPMNs with a low risk of malignancy. Copyright© 2017 International Institute of Anticancer Research (Dr. John G. Delinassios), All rights reserved.

  1. Feasibility study on commercialized fast reactor cycle systems. Phase II final report

    International Nuclear Information System (INIS)

    Ieda, Yoshiaki; Uchikawa, Sadao; Okubo, Tsutomu; Ono, Kiyoshi; Kato, Atsushi; Kurisaka, Kenichi; Sakamoto, Yoshihiko; Sato, Kazujiro; Sato, Koji; Chikazawa, Yoshitaka; Nakai, Ryodai; Nakabayashi, Hiroki; Nakamura, Hirofumi; Namekawa, Takashi; Niwa, Hajime; Nomura, Kazunori; Hayashi, Hideyuki; Hayafune, Hiroki; Hirao, Kazunori; Mizuno, Tomoyasu; Muramatsu, Toshiharu; Ando, Masato; Ono, Katsumi; Ogata, Takanari; Kubo, Shigenobu; Kotake, Shoji; Sagayama, Yutaka; Takakuma, Katsuyuki; Tanaka, Toshihiko; Namba, Takashi; Fujii, Sumio; Muramatsu, Kazuyoshi

    2006-06-01

    A joint project team of Japan Atomic Energy Agency and the Japan Atomic Power Company (as the representative of the electric utilities) started the feasibility study on commercialized fast reactor cycle systems (F/S) in July 1999 in cooperation with Central Research Institute of Electric Power Industry and vendors. On the major premise of safety assurance, F/S aims to present an appropriate picture of commercialization of fast reactor (FR) cycle system which has economic competitiveness with light water reactor cycle systems and other electricity base load systems, and to establish FR cycle technologies for the future major energy supply. In the period from Japanese fiscal year (JFY) 1999 to 2000, the phase-I of F/S was carried out to screen our representative FR, reprocessing and fuel fabrication technologies. In the phase-II (JFY 2001-2005), the design study of FR cycle concepts, the development of significant technologies necessary for the feasibility evaluation, and the confirmation of key technical issues were performed to clarify the promising candidate concepts toward the commercialization. In this final phase-II report clarified the most promising concept, the R and D plan until around 2015, and the key issues for the commercialization. Based on the comprehensive evaluation in F/S, the combination of the sodium-cooled FR with MOX fuel core, the advanced-aqueous reprocessing process and the simplified-pelletizing fuel fabrication process was recommended as the mainline choice for the most promising concept. The concept exceeds in technical advancement, and the conformity to the development targets was higher compared with that of the others. Alternative technologies are prepared to be decrease the development risk of innovative technologies in the mainline choice. (author)

  2. Feasibility Study of Economics and Performance of Solar PV at the Atlas Industrial Park in Duluth, Minnesota

    Energy Technology Data Exchange (ETDEWEB)

    Steen, M.; Lisell, L.; Mosey, G.

    2013-01-01

    The U.S. Environmental Protection Agency (EPA) Region 5, in accordance with the RE-Powering America's Land initiative, selected the Atlas Industrial Park in Duluth, Minnesota, for a feasibility study of renewable energy production. The EPA provided funding to the National Renewable Energy Laboratory (NREL) to support a feasibility study of solar renewable energy generation at the Atlas Industrial Park. NREL provided technical assistance for this project but did not assess environmental conditions at the site beyond those related to the performance of a photovoltaic (PV) system. The purpose of this study is to assess the site for a possible PV installation and estimate the cost, performance, and site impacts of different PV configurations. In addition, the study evaluates financing options that could assist in the implementation of a PV system at the site.

  3. A cask maintenance facility feasibility study

    International Nuclear Information System (INIS)

    Rennich, M.J.; Medley, L.G.; Attaway, C.R.

    1989-01-01

    The Oak Ridge National Laboratory (ORNL) is supporting the USDOE Office of Civilian Radioactive Waste Management (OCRWM) in developing a transportation system for spent nuclear fuel (SNF) and defense high level waste (HLW) as a part of the Federal Waste Management System (FWMS). In early 1988, a feasibility study was undertaken to design a stand-alone, green field facility for maintaining the FWMS casks. The feasibility study provided an initial layout facility design, an estimate of the construction cost, and an acquisition schedule for a Cask Maintenance Facility (CMF). The study also helped to define the interfaces between the transportation system and the waste generators, the repository, and a Monitored Retrieveable Storage (MRS) facility. The data, design, and estimated cost resulting from the study have been organized for use in the total transportation system decision-making process. Most importantly, the feasibility study also provides a foundation for continuing design and planning efforts. The feasibility study was based on an assumed stand-alone green field configuration because of the flexibility this design approach provides. A stand-alone facility requires the inclusion with support functions as well as the primary process facilities thus yielding a comprehensive design evaluation and cost estimate. For example, items such as roads, security and waste processing which might be shared with an integrated or collocated facility have been fully costed in the feasibility study. Thus, while the details of the facility design might change, the overall concept used in the study can be applied to other facility configurations as planning for the total FWMS develops

  4. Feasibility study on the interconnection of traction and other power line infrastructures; Machbarkeitsstudie zur Verknuepfung von Bahn- und Energieleitungsinfrastrukturen

    Energy Technology Data Exchange (ETDEWEB)

    Hofmann, Lutz [Hannover Univ. (Germany). Inst. fuer Energieversorgung und Hochspannungstechnik; Stephan, Arnd [Technische Univ. Dresden (Germany). Professur Elektrische Bahnen; Weyer, Hartmut [Technische Univ. Clausthal, Clausthal-Zellerfeld (Germany). Inst. fuer Deutsches und Internationales Berg- und Energierecht

    2013-06-15

    It was the purpose of the feasibility study to find out if and to what extent the existing transmission route potentials of the 16.7 Hz traction power network (DB Energie GmbH) can be used for the installation of new transmission lines of the standard 50 Hz power supply system. Of importance is here the question if and in which way the integration of new three-phase or DC overhead lines or cable systems in existing traction power routes is technically feasible, and to what extent such interconnection offers a potential for the acceleration of the planning and approval processes. (orig.)

  5. Feasibility of uranium enrichment in Australia

    International Nuclear Information System (INIS)

    1979-10-01

    The Council considered that provided the balance between costs and markets was found to be acceptable, there was no valid reason against the Government proceeding with a study on the feasibility of, and perhaps participating in the establishment of a commercial uranium enrichment industry in Australia. Areas covered include technical expertise and industrial structure in Australia, environmental aspects and safeguards

  6. Cogeneration using small sized series connected units: Feasibility study

    International Nuclear Information System (INIS)

    Tondelli, F.; Bergamini, G.

    1992-01-01

    This paper evidences the technical/economic feasibility of the use of methane fuelled modular cogeneration systems based on small series connected Otto or Diesel cycle engines delivering from 20 to 90 kW of power. Ample reference is made to the successful application of modular cogeneration systems to supply low temperature thermal energy to hospitals, hotels, food processing firms, etc., in Italy. The cost benefit analysis covers many aspects: design, manufacturing, operation, performance, maintenance and safety. Suggestions are also made as to optimum contractual arrangements for equipment service and maintenance, as well as, for the exchange of power with local utilities

  7. 100-BC-1 Operable Unit focused feasibility study

    International Nuclear Information System (INIS)

    Day, R.E.

    1994-01-01

    The standard Comprehensive Environmental Response, Compensation, and Liability Act feasibility study includes development and screening of alternatives (Phases 1 and 2) and the detailed analysis of alternatives (Phase 3). This focused feasibility study constitutes the Phase 3 portion of the feasibility study process for the remedial alternatives initially developed and screened in the 100 Area Feasibility Study Phases 1 and 2 (DOE-RL 1993a). The focused feasibility study process is conducted in two stages, a Process Document (DOE-RL 1994a) and an operable unit-specific focused feasibility study document, such as this one. The focused feasibility study process is performed by implementing a ''plug-in'' style approach; as defined in greater detail in the Process Document, which is a companion to this document. The objective of this focused feasibility study is to provide decision makers with sufficient information to allow appropriate and timely selection of interim remedial measures for candidate waste sites associated with the 100-BC-1 Operable Unit which is located in the north-central part of the Hanford Site. The interim remedial measure candidate waste sites are determined in the Limited Field Investigation (DOE-RL 1993b). Site profiles are developed for each of these waste sites. The site profiles are used in the application of the plug-in approach. The waste site either plugs into the analysis of the alternatives for the group, or deviations from the developed group alternatives are described and documented

  8. Base compaction specification feasibility analysis.

    Science.gov (United States)

    2012-12-01

    The objective of this research is to establish the technical engineering and cost : analysis concepts that will enable WisDOT management to objectively evaluate the : feasibility of switching construction specification philosophies for aggregate base...

  9. A Study to Determine the Biological Feasibility of a New Fish Tagging System; Annual Report 1994-1996.

    Energy Technology Data Exchange (ETDEWEB)

    Downing, Sandra L.; Frost, Deborah A.; Jonasson, Bruce F.; Nunnallee, Edmund P.; Peterson, Bradley W.; Prentice, Earl F.; Snell, Glen A.

    1998-11-01

    A multiyear program to evaluate the technical and biological feasibility of a new identification system for salmonids established between the Bonneville Power Administration (BPA) and the National Marine Fisheries Service (NMFS) in 1983.

  10. The feasibility study I on the blanket fuel options for the ATW/HYPER

    Energy Technology Data Exchange (ETDEWEB)

    Hwang, Woan; Lee, Byoung Oon; Lee, Bong Sang; Park, Won Seok; Meyer, M.K; Hayes, S.L

    2001-01-01

    The choice of a blanket fuel cycle technology and the fuel type for HYPER/ATW are important to develop an ADS with better economics, performance and safety. Even though several fuel types have been considered as an alternative of the blanket fuels for HYPER/ATW, the metal alloy and the dispersion fuels were selected as the candidate fuels for ADS, and the technical feasibilities for both fuels are evaluated in this report. General performance characteristics, fabrication abilities, technical aspects, safety aspects, economics, and non-proliferation aspects for each fuel type are reviewed and evaluated. And some technological problems are addressed in this report, focused on the development strategy, the roadmaps, and the flexibility to meet the missions and specific designs. This study has been performed at the first stage of conceptual design. Since it is under the lack of physical properties for each fuel material, no an attempt is made to select the best fuel option, but the more better fuel options are recommended.

  11. The feasibility study I on the blanket fuel options for the ATW/HYPER

    International Nuclear Information System (INIS)

    Hwang, Woan; Lee, Byoung Oon; Lee, Bong Sang; Park, Won Seok; Meyer, M.K; Hayes, S.L.

    2001-01-01

    The choice of a blanket fuel cycle technology and the fuel type for HYPER/ATW are important to develop an ADS with better economics, performance and safety. Even though several fuel types have been considered as an alternative of the blanket fuels for HYPER/ATW, the metal alloy and the dispersion fuels were selected as the candidate fuels for ADS, and the technical feasibilities for both fuels are evaluated in this report. General performance characteristics, fabrication abilities, technical aspects, safety aspects, economics, and non-proliferation aspects for each fuel type are reviewed and evaluated. And some technological problems are addressed in this report, focused on the development strategy, the roadmaps, and the flexibility to meet the missions and specific designs. This study has been performed at the first stage of conceptual design. Since it is under the lack of physical properties for each fuel material, no an attempt is made to select the best fuel option, but the more better fuel options are recommended

  12. PRE-FEASIBILITY STUDY FOR TREATMENT WETLAND APPLICATION FOR WASTEWATER TREATMENT IN DISPERSED DEVELOPMENT

    Directory of Open Access Journals (Sweden)

    Magdalena Gajewska

    2016-07-01

    Full Text Available The aim of the paper is to present the conducted analyses of pre-feasibility study of different approaches for wastewater management in a settlement of 180 persons. In the assessment both technical and economic aspects were analyzed. The costs were calculated for three different and, at the same time, most popular as well as possible technical solutions like: (i construction of local wastewater treatment plant with gravitational and pressurized networks, (ii construction of single family wastewater treatment plants, (iii construction of sealed septic tanks. Carried out analyses of investment and maintenance costs revealed that at the stage of construction the most expensive is local sewer network with treatment plant, while the construction of a single family treatment plant has similar cost regardless of the technology used. When the long term operation and investment cost are accounted the most economical reasonable solution is the application of wetland treatment for household wastewater treatment.

  13. Studies on the feasibility of heavy ion beams for inertial confinement fusion

    International Nuclear Information System (INIS)

    1983-05-01

    This Annual Report summarizes the scientific results of work carried out in 1982 in the framework of a feasibility study for inertial confinement fusion with heavy ion beams funded by the German Ministry of Research and Technology. The principal aim of this basic research program is the investigation of key problems and the identification of critical issues of the heavy ion ICF concept in the fields of accelerator research, atomic physics, target physics, and reactor design. The research is carried out by about ten working groups at various research centers and universities. One of the highlights in 1982 was a symposium held end of March at GSI which focussed on a critical analysis of the HIBALL accelerator concept. Whereas technical issues and hardware parameters were found feasible the beam dynamics in the storage rings turned out to be beyond the so far believed stability limits. As a consequence a revised accelerator scenario based on a lower charge state and a higher linac current has been investigated during the last year. First considerations were made on an experimental facility necessary for the study of high-intensity beam dynamics and of beam target interaction. Experimental studies of this kind will be of increasing importance for the future of the project. (orig.) [de

  14. Scout fourth stage attitude and velocity control (AVC) system feasibility study

    Science.gov (United States)

    Byars, L. B.

    1975-01-01

    The feasibility of incorporating a guidance system in the Scout fourth stage to achieve a significant improvement in expected payload delivery accuracy is studied. The technical investigations included the determination of the AVC equipment performance requirements, establishment of qualification and acceptance test levels, generation of layouts illustrating design approaches for the upper D and payload transition sections to incorporate the hardware, and the preparation of a vendor bid package. Correction concepts, utilizing inertial velocity and attitude, were identified and evaluated. Fourth stage attitude adjustments as determined from inertial velocity variation through the first three stages and a final velocity correction based upon the measured in-plane component errors at injection were employed. Results show radical reductions in apogee-perigee deviations.

  15. The feasibility study: a health economics perspective

    Directory of Open Access Journals (Sweden)

    Brenda Gannon

    2017-02-01

    Full Text Available The remit of research funding bodies is to prioritise funding for research that is of relevance and of high quality. This in turn will aim to raise the quality of healthcare and benefit to patients. Researchers are faced with increasing demands and expectations from the public purse and patients. The emphasis is to improve the quality of their research, with the ultimate aim of improving population health. While guidelines on feasibility study methods concentrate heavily on trials, there appears less guidance on application of health economics within feasibility studies, yet these are a less costly way to determine first of all if a full randomised controlled trial (RCT is feasible. A feasibility study assesses if the study can be done in a small RCT type study. Since by definition, a feasibility study does not evaluate the outcome, researchers often omit the health economics aspects but do however include statistical analysis. This leaves a gap in interpretation for policy makers and potential funders. It also means that any resulting publication does not include relevant information and therefore comparison across studies in terms of difficulty in collecting cost data is not possible. The main aim of this commentary therefore, is to demonstrate a suggested health economics analysis within a feasibility study and to recommend to researchers to include these aspects from the conception of their intervention. This paper proposes a number of points, with rationale for each point, to indicate the health economics data and the potential benefits required for coherent interpretation of the feasibility of future economic evaluations in a full trial. Economic evaluation is necessary if implementation into standard care is anticipated. Therefore, collection and summary analysis of relevant data is good practice at each point of the intervention development. Current guidelines for economic evaluation, for example, The Medical Research Guidelines in the

  16. Composite Socio-Technical Systems: A Method for Social Energy Systems

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Yingchen [National Renewable Energy Laboratory (NREL), Golden, CO (United States); He, Fulin [Huazhong University of Science & Technology; Hao, Jun [University of Denver; Dai, Xiaoxiao [University of Denver; Zhang, Jun Jason [University of Denver; Wei, Jiaolong [Huazhong University of Science & Technology

    2017-12-01

    In order to model and study the interactions between social on technical systems, a systemic method, namely the composite socio-technical systems (CSTS), is proposed to incorporate social systems, technical systems and the interaction mechanism between them. A case study on University of Denver (DU) campus grid is presented in paper to demonstrate the application of the proposed method. In the case study, the social system, technical system, and the interaction mechanism are defined and modelled within the framework of CSTS. Distributed and centralized control and management schemes are investigated, respectively, and numerical results verifies the feasibility and performance of the proposed composite system method.

  17. Feasibility study about handling plant and logistics of rotted spruce for energy and pulpwood; Esiselvitys energia- ja teollisuuspuun kaesittelylaitteistosta ja logistiikasta

    Energy Technology Data Exchange (ETDEWEB)

    Laurila, P [Biowatti Oy, Espoo (Finland)

    1997-12-01

    The aim of this feasibility study is to clarify the handling demands, technical and logistical possibilities, profitabilities both outlays and benefits in combined energy- and pulpwood production from rotted spruce raw material. The results of the study will be taken into consideration, if a handling plant will be decided to build and demonstrate beside the Forssa biomass power plant. (orig.)

  18. Solar UV exposure among outdoor workers in Denmark measured with personal UV-B dosimeters: technical and practical feasibility.

    Science.gov (United States)

    Grandahl, Kasper; Mortensen, Ole Steen; Sherman, David Zim; Køster, Brian; Lund, Paul-Anker; Ibler, Kristina Sophie; Eriksen, Paul

    2017-10-10

    Exposure to solar ultraviolet radiation is a well-known cause of skin cancer. This is problematic for outdoor workers. In Denmark alone, occupational skin cancer poses a significant health and safety risk for around 400,000 outdoor workers. Objective measures of solar ultraviolet radiation exposure are needed to help resolve this problem. This can be done using personal ultraviolet radiation dosimeters. We consider technical and practical feasibility of measuring individual solar ultraviolet exposure at work and leisure in professions with different á priori temporal high-level outdoor worktime, using aluminium gallium nitride (AlGaN) photodiode detector based personal UV-B dosimeters. Essential technical specifications including the spectral and angular responsivity of the dosimeters are described and pre-campaign dosimeter calibration applicability is verified. The scale and conduct of dosimeter deployment and campaign in-field measurements including failures and shortcomings affecting overall data collection are presented. Nationwide measurements for more than three hundred and fifty workers from several different professions were collected in the summer of 2016. On average, each worker's exposure was measured for a 2-week period, which included both work and leisure. Data samples of exposure at work during a Midsummer day show differences across professions. A construction worker received high-level occupational UV exposure most of the working day, except during lunch hour, accumulating to 5.1 SED. A postal service worker was exposed intermittently around noon and in the afternoon, preceded by no exposure forenoon when packing mail, accumulating to 1.6 SED. A crane fitter was exposed only during lunch hour, accumulating to 0.7 SED. These findings are in line with our specialist knowledge as occupational physicians. Large-scale use of personal UV-B dosimeters for measurement of solar ultraviolet radiation exposure at work and leisure in Denmark is indeed

  19. Critical technical issues and evaluation and comparison studies for inertial fusion energy reactors

    Energy Technology Data Exchange (ETDEWEB)

    Abdou, M.A. (Mechanical, Aerospace and Nuclear Engineering Dept., Univ. of California, Los Angeles, CA (United States)); Ying, A.Y. (Mechanical, Aerospace and Nuclear Engineering Dept., Univ. of California, Los Angeles, CA (United States)); Tillack, M.S. (Mechanical, Aerospace and Nuclear Engineering Dept., Univ. of California, Los Angeles, CA (United States)); Ghoniem, N.M. (Mechanical, Aerospace and Nuclear Engineering Dept., Univ. of California, Los Angeles, CA (United States)); Waganer, L.M. (McDonnell Douglas Aerospace, St. Louis, MI (United States)); Driemeyer, D.E. (McDonnell Douglas Aerospace, St. Louis, MI (United States)); Linford, G.J. (TRW Space and Electronics Div., Redondo Beach, CA (United States)); Drake, D.J.

    1994-01-01

    Two inertial fusion energy (IFE) reactor design concepts developed in the Prometheus studies were evaluated. Objectives were to identify and characterize critical issues and the R and D required to resolve them, and to establish a sound basis for future IFE technical and programmatic decisions. Each critical issue contains several key physics and engineering issues associated with major reactor components and impacts key aspects of feasibility, safety, and economic potential of IFE reactors. Generic critical issues center around: demonstration of moderate gain at low driver energy, feasibility of direct drive targets, feasibility of indirect drive targets for heavy ions, feasibility of indirect drive targets for lasers, cost reduction strategies for heavy ion drivers, demonstration of higher overall laser driver efficiency, tritium self-sufficiency in IFE reactors, cavity clearing at IFE pulse repetition rates, performance/reliability/lifetime of final laser optics, viability of liquid metal film for first wall protection, fabricability/reliability/lifetime of SiC composite structures, validation of radiation shielding requirements, design tools, and nuclear data, reliability and lifetime of laser and heavy ion drivers, demonstration of large-scale non-linear optical laser driver architecture, demonstration of cost effective KrF amplifiers, and demonstration of low cost, high volume target production techniques. Quantitative evaluation and comparison of the two design options have been made with special focus on physics feasibility, engineering feasibility, economics, safety and environment, and research and development (R and D) requirements. Two key conclusions are made based on the overall evaluation analysis. The heavy-ion driven reactors appear to have an overall advantage over laser-driven reactors.

  20. A cask maintenance facility feasibility study

    International Nuclear Information System (INIS)

    Rennich, M.J.; Medley, L.G.; Attaway, C.R.

    1989-01-01

    The Oak Ridge National Laboratory (ORNL) is developing a transportation system for spent nuclear fuel (SNF) and defense high level waste (HLW) as a part of the Federal Waste Management System (FWMS). In early 1988, a feasibility study was undertaken to design a stand-alone, ''green field'' facility for maintaining the FWMS casks. The feasibility study provided an initial layout facility design, an estimate of the construction cost, and an acquisition schedule for a Cask Maintenance Facility (CMF). The study also helped to define the interfaces between the transportation system and the waste generators, the repository, and a Monitored Retrievable Storage (MRS) facility. The data, design, and estimated costs resulting from the study have been organized for use in the total transportation system decision-making process. Most importantly, the feasibility study also provides a foundation for continuing design and planning efforts. Fleet servicing facility studies, operational studies from current cask system operators, a definition of the CMF system requirements, and the experience of others in the radioactive waste transportation field were used as a basis for the feasibility study. In addition, several cask handling facilities were visited to observe and discuss cask operations to establish the functions and methods of cask maintenance expected to be used in the facility. Finally, a peer review meeting was held at Oak Ridge, Tennessee in August, 1988, in which the assumptions, design, layout, and functions of the CMF were significantly refined. Attendees included representatives from industry, the repository and transportation operations

  1. Monte Carlo simulation for pixel detectors: a feasibility study for X radiation applications

    International Nuclear Information System (INIS)

    Marinho, F.; Akiba, K.

    2014-01-01

    In this paper we analyze the feasibility of a Monte Carlo simulation for the description of pixel semiconductor detectors as a tool for research and development of such devices and their applications for X-rays. We present as a result the technical aspects and main characteristics of a set of algorithms recently developed which allows one to estimate the energy spectrum and cluster classification. (author)

  2. Feasibility study and technical proposal for long-term observations of bedrock stability with gps

    International Nuclear Information System (INIS)

    Ruizhi Chen; Kakkuri, J.

    1994-01-01

    In order to study the regional crustal deformation pattern in the territory of Finland, the Finnish Geodetic Institute is establishing the Finnish Permanent GPS Network, which is part of the Fennoscandian Permanent GPS Network. The Finnish GPS Network consists of a 12 stations located in different geological structures. The operation procedure of the network is described in the report. Feasibility study for monitoring the bedrock stability at local scale was performed. The study was carried out on the basis of an experiment on a baseline of 1041 metres. Twelve artificial movements ranging from 1 mm to 22 mm were generated with a precision-manufactured screw drive (with an accuracy of better than +-0.05 mm). The artificial movements were then detected with the GPS measurements. A preliminary analysis of the GPS data shows that the maximum difference between the GPS detected movements and the artificial movements is 0.9 mm with a standard deviation of +-0.46 mm. The observation time for reaching such accuracy is about 55 minutes. Three GPS networks were preliminarily designed for the radioactive waste disposal investigation sites of Olkiluoto, Kivetty and Romuvaara. Detailed research plan for achieving the best possible result from GPS measurements was proposed. (58 refs., 25 figs., 1 tab.)

  3. Technical feasibility assessment of oleic sunflower methyl ester utilisation in Diesel bus engines

    International Nuclear Information System (INIS)

    Silva, Fernando Neto da; Prata, Antonio Salgado; Teixeira, Jorge Rocha

    2003-01-01

    This paper describes the results obtained while testing the technical feasibility of using oleic sunflower methyl ester (SME) blended with Diesel fuel in proportions up to 30% in an unmodified Diesel bus engine. Vegetable oils methyl esters blended with Diesel oil are commonly used in compression ignition engines. However, R and D background information on the practical use of traditional sunflower oil derivatives is sparse. The present results include evaluation of the engine performance and fuel consumption and gaseous concentrations (CO and NO x ) in the exhaust gas. The exhaust gas opacity while using Diesel/SME blends and Diesel fuel was also compared. The collected data show that oleic SME utilisation did not lead to a deterioration of engine performance or to an increase in fuel consumption. Furthermore, significant increases of NO x and CO concentrations in the exhaust gas derived from SME utilisation were not detected. The smoke opacity was slightly reduced when SME was used in the proportion of 30%. The experimental testing seems to indicate that oleic SME is a suitable replacement for Diesel fuel and can be used safely in compression ignition engines in proportions as high as 30%. (Author)

  4. Technical feasibility assessment of oleic sunflower methyl ester utilisation in Diesel bus engines

    International Nuclear Information System (INIS)

    Neto da Silva, Fernando; Salgado Prata, Antonio; Rocha Teixeira, Jorge

    2003-01-01

    This paper describes the results obtained while testing the technical feasibility of using oleic sunflower methyl ester (SME) blended with Diesel fuel in proportions up to 30% in an unmodified Diesel bus engine. Vegetable oils methyl esters blended with Diesel oil are commonly used in compression ignition engines. However, R and D background information on the practical use of traditional sunflower oil derivatives is sparse. The present results include evaluation of the engine performance and fuel consumption and gaseous concentrations (CO and NO X ) in the exhaust gas. The exhaust gas opacity while using Diesel/SME blends and Diesel fuel was also compared. The collected data show that oleic SME utilisation did not lead to a deterioration of engine performance or to an increase in fuel consumption. Furthermore, significant increases of NO X and CO concentrations in the exhaust gas derived from SME utilisation were not detected. The smoke opacity was slightly reduced when SME was used in the proportion of 30%. The experimental testing seems to indicate that oleic SME is a suitable replacement for Diesel fuel and can be used safely in compression ignition engines in proportions as high as 30%

  5. An independent assessment of the technical feasibility of the Mars One mission plan - Updated analysis

    Science.gov (United States)

    Do, Sydney; Owens, Andrew; Ho, Koki; Schreiner, Samuel; de Weck, Olivier

    2016-03-01

    In recent years, the Mars One program has gained significant publicity for its plans to colonize the red planet. Beginning in 2025, the program plans to land four people on Mars every 26 months via a series of one-way missions, using exclusively existing technology. This one-way approach has frequently been cited as a key enabler of accelerating the first crewed landing on Mars. While the Mars One program has received considerable attention, little has been published in the technical literature regarding the formulation of its mission architecture. In light of this, we perform an independent analysis of the technical feasibility of the Mars One mission plan, focusing on the architecture of the life support and in-situ resource utilization (ISRU) systems, and their impact on sparing and space logistics. To perform this analysis, we adopt an iterative analysis approach in which we model and simulate the mission architecture, assess its feasibility, implement any applicable modifications while attempting to remain within the constraints set forth by Mars One, and then resimulate and reanalyze the revised version of the mission architecture. Where required information regarding the Mars One mission architecture is not available, we assume numerical values derived from standard spaceflight design handbooks and documents. Through four iterations of this process, our analysis finds that the Mars One mission plan, as publicly described, is not feasible. This conclusion is obtained from analyses based on mission assumptions derived from and constrained by statements made by Mars One, and is the result of the following findings: (1) several technologies including ISRU, life support, and entry, descent, and landing (EDL) are not currently "existing, validated and available" as claimed by Mars One; (2) the crop growth area described by Mars One is insufficient to feed their crew; (3) increasing the crop growth area to provide sufficient food for the crew leads to atmospheric

  6. Critical technical issues and evaluation and comparison studies for inertial fusion energy reactors

    International Nuclear Information System (INIS)

    Abdou, M.A.; Ying, A.Y.; Tillack, M.S.; Ghoniem, N.M.; Waganer, L.M.; Driemeyer, D.E.; Linford, G.J.; Drake, D.J.

    1994-01-01

    The critical issues, evaluation and comparison of two inertial fusion energy (IFE) reactor design concepts developed in the Prometheus studies are presented. The objectives were (1) to identify and characterize the critical issues and the R and D required to solve them, and (2) to establish a sound basis for future IFE technical and programmatic decisions by evaluating and comparing the different design concepts. Quantitative evaluation and comparison of the two design options have been made with special focus on physics feasibility, engineering feasibility, economics, safety and environment, and research and development (R and D) requirements. Two key conclusions are made based on the overall evaluation analysis: (1) The heavy-ion driven reactors appear to have an overall advantage over laser-driven reactors; and: (2) The differences in scores are not large and future results of R and D could change the overall ranking of the two IFE concepts

  7. Strategic analysis for safeguards systems: a feasibility study. Volume 1. Main report

    International Nuclear Information System (INIS)

    Seaver, D.A.; Cohen, M.S.; Immerman, W.H.; Crane, F.L.; Goldman, A.J.

    1984-12-01

    Strategic analysis (game theory) is a formal method for modeling adversary situations that, when solved, yields an optimal strategy that maximizes the expected payoff to the player. As such, it appears to be potentially applicable in the nuclear material accounting context in which there is potential for an adversary attempting to divert special nuclear material. The NRC has previously supported research to develop preliminary strategic analysis models which has been considered to be only partially successful. This study reviewed previous efforts and other game theory research and assessed the feasibility of: (1) applying strategic analysis in a regulatory framework; (2) making strategic analysis understandable by licensees; and (3) assuring that strategic analysis can effectively be enforced. This report includes a discussion of the role of strategic analysis in material control and accounting, and of the mechanisms by which the NRC could implement strategic analysis. A set of feasibility criteria are described including both technical feasibility and organizational/implementation feasibility. Alternative strategic analysis model options are evaluated with respect to these criteria, as is the current material accounting practice. The assessment determined that the development of a payoff function that adequately represented the NRC's (and therefore the public's) values with respect to the consequences of diversion and the actions taken to prevent it is the most serious impediment to implementation. Given the limited role of material accounting in safeguards and the uncertainty regarding the development of a payoff function, the NRC should not proceed with full-scale implementation of strategic analysis. It does, however, have sufficient potential to warrant further development, with first priority going to the development of an appropriate payoff function

  8. Feasibility study for adding a demand failure data collection system to the Nuclear Plant Reliability Data System. Final report

    International Nuclear Information System (INIS)

    Tashjian, B.M.; Logan, B.W.

    1983-07-01

    Southwest Research Institute (SwRI) is pleased to submit to Sandia National Laboratories this technical report as fulfillment of Task 5 of the proposal entitled A Feasibility Study for Adding a Duty Cycle Data Collection System to the Nuclear Plant Reliability Data System. The purpose of this report is to summarize the work as delineated in the proposal tasks and to recommend follow-on activities. Technical support for this work was provided by Duke Power Company (Duke), subcontractor to SwRI. The four tasks to be performed in conjunction with the Duty Cycle Data Collection Study (renamed in this report Demand Data Collection) were: define component population and measurable parameters; develop data collection and assessment methodologies; assess the impact on utilities; and assess the impact on NPRDS

  9. Feasibility study analysis for multi-function dual energy oven (case study: tapioca crackers small medium enterprise)

    Science.gov (United States)

    Soraya, N. W.; El Hadi, R. M.; Chumaidiyah, E.; Tripiawan, W.

    2017-12-01

    Conventional drying process is constrained by weather (cloudy / rainy), and requires wide drying area, and provides low-quality product. Multi-function dual energy oven is the appropriate technology to solve these problems. The oven uses solar thermal or gas heat for drying various type of products, including tapioca crackers. Investment analysis in technical, operational, and financial aspects show that the multi-function dual energy oven is feasible to be implemented for small medium enterprise (SME) processing tapioca crackers.

  10. Feasibility of developing a portable driver performance data acquisition system for human factors research: Technical tasks. Volume 1

    Energy Technology Data Exchange (ETDEWEB)

    Carter, R.J.; Barickman, F.S.; Spelt, P.F.; Schmoyer, R.L.; Kirkpatrick, J.R.

    1998-01-01

    A two-phase, multi-year research program entitled ``development of a portable driver performance data acquisition system for human factors research`` was recently completed. The primary objective of the project was to develop a portable data acquisition system for crash avoidance research (DASCAR) that will allow drive performance data to be collected using a large variety of vehicle types and that would be capable of being installed on a given vehicle type within a relatively short-time frame. During phase 1 a feasibility study for designing and fabricating DASCAR was conducted. In phase 2 of the research DASCAR was actually developed and validated. This technical memorandum documents the results from the feasibility study. It is subdivided into three volumes. Volume one (this report) addresses the last five items in the phase 1 research and the first issue in the second phase of the project. Volumes two and three present the related appendices, and the design specifications developed for DASCAR respectively. The six tasks were oriented toward: identifying parameters and measures; identifying analysis tools and methods; identifying measurement techniques and state-of-the-art hardware and software; developing design requirements and specifications; determining the cost of one or more copies of the proposed data acquisition system; and designing a development plan and constructing DASCAR. This report also covers: the background to the program; the requirements for the project; micro camera testing; heat load calculations for the DASCAR instrumentation package in automobile trunks; phase 2 of the research; the DASCAR hardware and software delivered to the National Highway Traffic Safety Administration; and crash avoidance problems that can be addressed by DASCAR.

  11. Geocapacity: economic feasibility of CCS in networked systems

    NARCIS (Netherlands)

    Neele, F.; Hendriks, C.; Brandsma, R.

    2009-01-01

    A Decision Support System (DSS) has been developed to evaluate the technical and economical feasibility of CO2 storage in the subsurface. The DSS performs a detailed, stochastic analysis of the technical and economical aspects of a CCS project, which consists of any number of CO2 sources and sinks

  12. Head Start Impact Study. Technical Report

    Science.gov (United States)

    Puma, Michael; Bell, Stephen; Cook, Ronna; Heid, Camilla; Shapiro, Gary; Broene, Pam; Jenkins, Frank; Fletcher, Philip; Quinn, Liz; Friedman, Janet; Ciarico, Janet; Rohacek, Monica; Adams, Gina; Spier, Elizabeth

    2010-01-01

    This Technical Report is designed to provide technical detail to support the analysis and findings presented in the "Head Start Impact Study Final Report" (U.S. Department of Health and Human Services, January 2010). Chapter 1 provides an overview of the Head Start Impact Study and its findings. Chapter 2 provides technical information on the…

  13. Washoe Tribe Alternative Energy Feasibility Study Final Report

    Energy Technology Data Exchange (ETDEWEB)

    Johnson, Jennifer [Washoe Tribe of NV and CA

    2014-10-01

    The Washoe Tribe of Nevada and California was awarded funding to complete the Washoe Tribe Alternative Energy Feasibility Study project. The main goal of the project was to complete an alternative energy feasibility study. This study was completed to evaluate “the potential for development of a variety of renewable energy projects and to conduct an alternative energy feasibility study that determines which alternative energy resources have the greatest economic opportunity for the Tribe, while respecting cultural and environmental values” (Baker-Tilly, 2014). The study concluded that distributed generation solar projects are the best option for renewable energy development and asset ownership for the Washoe Tribe. Concentrating solar projects, utility scale wind projects, geothermal, and biomass resource projects were also evaluated during the study and it was determined that these alternatives would not be feasible at this time.

  14. Study of the techno-economic feasibilities of potato and onion irradiation in Syria

    International Nuclear Information System (INIS)

    Al-Bachir, M.; Sharabi, N.; Midani, M.A.

    1991-06-01

    Ionizing radiation has been used for food preservation in many ways, among them sprout inhibition in onion and potato. Experiments showed that irradiation of these crops using doses between 50 - 150 Gy prevented sprouting for up to 6 months during storage. Priliminary experiments in Syria proved the effectiveness of such treatment in these two crops. In addition to the technical, social, and political feasibility, this study includes, general description of the suggested plant ( 60 Co 3.7 PBq), estimated cost, location, and the tentative operation schedual. The study showed that the cost of irradiation will be about $ 8.7 per ton, this will save the country about $ 3.760.000 per year. The study showed the possitive effect of establishing this plant. (author). 74 refs., 44 tabs., 15 figs

  15. Feasibility study for the processing of Hanford Site cesium and strontium isotopic sources in the Hanford Waste Vitrification Plant

    International Nuclear Information System (INIS)

    Anantatmula, R.P.; Watrous, R.A.; Nelson, J.L.; Perez, J.M.; Peters, R.D.; Peterson, M.E.

    1991-09-01

    The final environmental impact statement for the disposal of defense-related wastes at the Hanford Site (Final Environmental Impact Statement: Disposal of Hanford Defense High-Level, Transuranic and Tank Wastes [HDW-EIS] [DOE 1987]) states that the preferred alternative for disposal of cesium and strontium wastes at the Hanford Site will be to package and ship these wastes to the commercial high-level waste repository. The Record of Decision for this EIS states that before shipment to a geologic repository, these wastes will be packaged in accordance with repository waste acceptance criteria. However, the high cost per canister for repository disposal and uncertainty about the acceptability of overpacked capsules by the repository suggest that additional alternative means of disposal be considered. Vitrification of the cesium and strontium salts in the Hanford Waste Vitrification Plant (HWVP) has been identified as a possible alternative to overpacking. Subsequently, Westinghouse Hanford Company's (Westinghouse Hanford) Projects Technical Support Office undertook a feasibility study to determine if any significant technical issues preclude the vitrification of the cesium and strontium salts. Based on the information presented in this report, it is considered technically feasible to blend the cesium chloride and strontium fluoride salts with neutralized current acid waste (NCAW) and/or complexant concentrate (CC) waste feedstreams, or to blend the salts with fresh frit and process the waste through the HWVP

  16. Do feasibility studies contribute to, or avoid, waste in research?

    Science.gov (United States)

    Morgan, Ben; Hejdenberg, Jennie; Hinrichs-Krapels, Saba; Armstrong, David

    2018-01-01

    In the context of avoiding research waste, the conduct of a feasibility study before a clinical trial should reduce the risk that further resources will be committed to a trial that is likely to 'fail'. However, there is little evidence indicating whether feasibility studies add to or reduce waste in research. Feasibility studies funded by the National Institute for Health Research's (NIHR) Research for Patient Benefit (RfPB) programme were examined to determine how many had published their findings, how many had applied for further funding for a full trial and the timeframe in which both of these occurred. A total of 120 feasibility studies which had closed by May 2016 were identified and each Principal Investigator (PI) was sent a questionnaire of which 89 responses were received and deemed suitable for analysis. Based on self reported answers from the PIs a total of 57 feasibility studies were judged as feasible, 20 were judged not feasible and for 12 it was judged as uncertain whether a full trial was feasible. The RfPB programme had spent approximately £19.5m on the 89 feasibility studies of which 16 further studies had been subsequently funded to a total of £16.8m. The 20 feasibility studies which were judged as not feasible potentially saved up to approximately £20m of further research funding which would likely to have not completed successfully. The average RfPB feasibility study took 31 months (range 18 to 48) to complete and cost £219,048 (range £72,031 to £326,830) and the average full trial funded from an RfPB feasibility study took 42 months (range 26 to 55) to complete and cost £1,163,996 (range £321,403 to £2,099,813). The average timeframe of feasibility study and full trial was 72 months (range 56 to 91), however in addition to this time an average of 10 months (range -7 to 29) was taken between the end of the feasibility study and the application for the full trial, and a further average of 18 months (range 13 to 28) between the

  17. Technical economic feasibility study for the implementation of a nuclear power plant for the production of electricity in Colombia; Estudio de factibilidad tecnico economica para la implementacion de una central de energia nuclear para la produccion de energia electrica en Colombia

    Energy Technology Data Exchange (ETDEWEB)

    Gonzales, David E.; Bolanos, Hernan G.; Mayorga, Manuel A.; Rodriguez, Edwin A., E-mail: david_egO@yahoo.es, E-mail: hernanbolaos@yahoo.com.ar, E-mail: alejo_mayorga@yahoo.com, E-mail: edwin.rodriguez@distoyota.com.co [Escuela Colombiana de Carreras Industriales (ECCI), Bogota (Colombia). Grupo de Investigacion GIATME

    2013-07-01

    A study on the technical and economic feasibility will be used to implement a nuclear power in Colombia to generate electricity. To this will be searched if there are previous studies on this topic and what they concluded. The manner in which power is supplied will be discussed in a national level nowadays, its strengths and weaknesses. It will be investigated the legal norms that exists in the country on nuclear power and renewable energy sources, the standards established at world level, the nuclear accidents and the great examples. Providers will be sought on the world market nuclear equipment which serve to this purpose and the technical characteristics of these equipment will be discussed. The type of fuel used in nuclear reactors, its origin, method of production, specifications, availability and long-term and safe handling and final disposal are considered. safe handling of this technology and policy or international rules that will studied.

  18. Feasibility study of a pressure fed engine for a water recoverable space shuttle booster Volume 2: Technical, phase A effort

    Science.gov (United States)

    1972-01-01

    Design and systems considerations are presented on an engine concept selection for further preliminary design and program evaluation. These data have been prepared from a feasibility study of a pressure-fed engine for the water recoverable space shuttle booster.

  19. Strategy for assessing the technical, environmental, and engineering feasibility of subseabed disposal

    International Nuclear Information System (INIS)

    Anderson, D.R.; Boyer, D.G.; Herrmann, H.; Kelly, J.; Talbert, D.M.

    1980-01-01

    This paper presents the strategy and management techniques used in the development of the US Subseabed Disposal Program (SDP) for possible disposal of both high-level waste and spent fuel. These have been developed through joint efforts of the Department of Energy (DOE), Division of Waste Isolation, the Sandia Technical Program Manager, the Technical Program Coordinators, the Advisory Group, and the Principal Investigators. Three subsections of this paper address the various components which make up the SDP strategy and management techniques. The first section will summarize the US DOE high-level waste and spent fuel disposal program and the position that the SDP occupies within that program. The second section, the Subseabed Program Plan, addresses the technical and administrative tools which are employed to facilitate the day-to-day operation of the SDP. The third section addresses the current studies and future plans for addressing the legal, political, and international uncertainties that must be resolved prior to the time the SDP reaches the final engineering phases

  20. A study of critical paths for feasibility studies of mining projects

    International Nuclear Information System (INIS)

    Sayadi, R.

    2002-01-01

    This work develops a model for design and realisation of profitability's and feasibility studies of a mining project. The model provides the structure of various necessary procedures to establish the feasibility studies and presents a logical system of task sequencing and information circulating between tasks. The specifications of mining projects, particularly their duration, complexity and high costs, necessitate design and realisation of feasibility study bases on the sufficient understanding of task behaviour and the critical path method view. For this purpose, critical paths with the highest frequency of occurrence were studied through several simulations. In addition, the critical tasks and sub tasks with the most probability were identified. The model introduced in this paper can serve as a perfect tool in feasibility study of a mining project. It can also be used as a basis of future development of mining software

  1. Technical and economic feasibility study for the reactivation of the integral test facility of IPEN/CNEN Nuclear Engineering Center

    Energy Technology Data Exchange (ETDEWEB)

    Biaty, Flávia P.; Rocha, Marcelo da S.; Oliveira, Otávio L. de, E-mail: flavia.biaty@usp.br, E-mail: msrocha@ipen.br, E-mail: otavioluis@ipen.br [Instituto de Pesquisas Energéticas e Nucleares (IPEN/CNEN-SP), São Paulo, SP (Brazil)

    2017-07-01

    The Integral Test Facility of Nuclear Engineering Center (CEN/IPEN/CNEN-SP), known as 'Loop 70', is a semi-industrial thermal-hydraulic test facility and can operate as a BWR (Boiling Water Reactor) or a PWR (Pressurizing Water Reactor) mode. Designed and built in the 1980's, it is currently disabled. The experimental circuits ('test loop') are facilities that reproduce the thermohydraulic and fluid dynamic conditions that occur inside a reactor and are used to simulate the practical reality which it is not possible to be obtained through mathematical models. In this context, this research project aims the development of a Business Plan to analyze the technical and economic feasibility related to the reactivation of the facility. This methodology (adapted to the government sector) is a decision-making tool that will offer a wide perspective of the project, set the guidelines and actions that will define the future of the facility and provide a general rule to make investments on it. This paper presents the historic aspects to better understand the Loop 70's current situation. It also presents information about similar facilities around the world, services that can be offered (thermal-hydraulics parameters measurements, equipment qualification and transient analysis due accident situations), results of the strategic analysis (SWOT) performed, specific goals for each critical success or failure factor of the facility, financial aspects related to the reactivation and an overview of the facility's perspectives. (author)

  2. Technical and economic feasibility study for the reactivation of the integral test facility of IPEN/CNEN Nuclear Engineering Center

    International Nuclear Information System (INIS)

    Biaty, Flávia P.; Rocha, Marcelo da S.; Oliveira, Otávio L. de

    2017-01-01

    The Integral Test Facility of Nuclear Engineering Center (CEN/IPEN/CNEN-SP), known as 'Loop 70', is a semi-industrial thermal-hydraulic test facility and can operate as a BWR (Boiling Water Reactor) or a PWR (Pressurizing Water Reactor) mode. Designed and built in the 1980's, it is currently disabled. The experimental circuits ('test loop') are facilities that reproduce the thermohydraulic and fluid dynamic conditions that occur inside a reactor and are used to simulate the practical reality which it is not possible to be obtained through mathematical models. In this context, this research project aims the development of a Business Plan to analyze the technical and economic feasibility related to the reactivation of the facility. This methodology (adapted to the government sector) is a decision-making tool that will offer a wide perspective of the project, set the guidelines and actions that will define the future of the facility and provide a general rule to make investments on it. This paper presents the historic aspects to better understand the Loop 70's current situation. It also presents information about similar facilities around the world, services that can be offered (thermal-hydraulics parameters measurements, equipment qualification and transient analysis due accident situations), results of the strategic analysis (SWOT) performed, specific goals for each critical success or failure factor of the facility, financial aspects related to the reactivation and an overview of the facility's perspectives. (author)

  3. Technical feasibility and costs of the retention of radionuclides during accidents in nuclear power plants demonstrated by the example of a pressurized water reactor

    International Nuclear Information System (INIS)

    Braun, H.; Grigull, R.; Lahner, K.; Gutowski, H.; Weber, J.

    1985-01-01

    The maximum allowable radiation doses during accidents in nuclear power plants, i.e., 5 rem whole-body dose and 15 rem thyroid dose, have been laid down in the German Radiation Protection Act. In order to ensure that these limits are not exceeded for all exposure paths including the ingestion path or, if possible, to remain far below them, the Federal Ministry of the Interior has initiated a study on the effectiveness and cost of additional safety features for reducing the release of activity and the dose exposure during accidents in nuclear power plants. Detailed investigations were carried out for the following three radiologically representative types of accidents: break of a reactor coolant line, break of an instrument line in one of the outer ring rooms, and break of a main stream line outside the containment. The technical basis of the study was a BBR-type nuclear power plant with pressurized water reactor and once-through steam generator. I-131 was chosen for determining the activity release as this is the critical nuclide for the ingestion path. Altogether 33 feasible technical measures were investigated and their potential improvement was assessed

  4. Extraforaminal Lumbar Interbody Fusion at the L5-S1 Level: Technical Considerations and Feasibility.

    Science.gov (United States)

    Kurzbuch, Arthur Robert; Kaech, Denis; Baranowski, Pawel; Baranowska, Alicja; Recoules-Arche, Didier

    2017-09-01

    Background  Extraforaminal lumbar interbody fusion (ELIF) surgery is a muscle-sparing approach that allows the treatment of various degenerative spinal diseases. It is technical challenging to perform the ELIF approach at the L5-S1 level because the sacral ala obstructs the view of the intervertebral disk space. Methods  We reported earlier on the ELIF technique in which the intervertebral disk is targeted at an angle of 45 degrees relative to the midline. In this article we describe the technical process we developed to overcome the anatomic relation between the sacral ala and the intervertebral disk space L5-S1 that hinders the ELIF approach at this level. We then report in a retrospective analysis on the short-term clinical and radiologic outcome of 100 consecutive patients with degenerative L5-S1 pathologies who underwent ELIF surgery. Results  The L5-S1 ELIF approach could be realized in all patients. The short-term clinical outcome was evaluated 5 months after surgery: 92% of the patients were satisfied with their postoperative result; 8% had a poor result. Overall, 17% of the patients presented light radicular or low back pain not influencing their daily activity, and 82% of the patients working before surgery returned to work 3 to 7 months after surgery. The radiologic outcome was documented by computed tomography at 5 months after surgery and showed fusion in 99% of the patients. Lumbar magnetic resonance imaging performed in 5 patients at 6 months after surgery revealed the integrity of the paraspinal muscles. Conclusions  ELIF surgery at the L5-S1 level is technically feasible for various degenerative spinal diseases. Analysis of the clinical and radiologic data in a consecutive retrospective cohort of patients who underwent this surgical procedure showed a good short-term clinical outcome and fusion rate. Georg Thieme Verlag KG Stuttgart · New York.

  5. A feasibility study on the vitrification of low-level radioactive waste

    Energy Technology Data Exchange (ETDEWEB)

    Song, Myung Jae; Park, Jong Kil; Ahn, Hee Jin [Korea Electric Power Corp. (KEPCO), Taejon (Korea, Republic of). Research Center; Cho, Jeong Mi; Choe, Young Son; Cho, Myeong Ryul [Hankuk Fiber Group (Korea, Republic of)

    1995-12-31

    A Study was carried out to investigate the feasibility of vitrification for low-and medium-level radioactive waste(LMLW). In order to understand maximum yearly generation volume and composition for each waste streams waste generation trends, which have been produced from nuclear power plants(PWR) in korea, were examined and then technical and economical assessment were performed based on the volume and composition. To select the most promising melters, technical characteristics were analyzed for several melters such as cold crucible melter heated by direct induction(CCM), cold crucible melter heated by vertical electrodes(CCVE), molten metal melter(MM), and plasma melter(PM) which were most likely to be applied to LMLW treatment. Economical assessment was carried out for several treatment strategies with selected melters and resulted in that it was desirable that non-combustibles and spent filter were vitrified with PM, and the others with CCM. For the demonstration of vitrification possibility for protective clothing, vinyl seats, spent resin, and evaporator bottoms, the surrogated wastes were paralyzed or dried at optimal conditions and than specimens contained various percentages of pyrolysis ash were prepared with lab. and pilot scale melters. Compressive strength for these specimens was measured to determine the maximum ash content in glass waste forms. (author). 27 refs., 88 figs.

  6. A feasibility study on the vitrification of low-level radioactive waste

    Energy Technology Data Exchange (ETDEWEB)

    Song, Myung Jae; Park, Jong Kil; Ahn, Hee Jin [Korea Electric Power Corp. (KEPCO), Taejon (Korea, Republic of). Research Center; Cho, Jeong Mi; Choe, Young Son; Cho, Myeong Ryul [Hankuk Fiber Group (Korea, Republic of)

    1996-12-31

    A Study was carried out to investigate the feasibility of vitrification for low-and medium-level radioactive waste(LMLW). In order to understand maximum yearly generation volume and composition for each waste streams waste generation trends, which have been produced from nuclear power plants(PWR) in korea, were examined and then technical and economical assessment were performed based on the volume and composition. To select the most promising melters, technical characteristics were analyzed for several melters such as cold crucible melter heated by direct induction(CCM), cold crucible melter heated by vertical electrodes(CCVE), molten metal melter(MM), and plasma melter(PM) which were most likely to be applied to LMLW treatment. Economical assessment was carried out for several treatment strategies with selected melters and resulted in that it was desirable that non-combustibles and spent filter were vitrified with PM, and the others with CCM. For the demonstration of vitrification possibility for protective clothing, vinyl seats, spent resin, and evaporator bottoms, the surrogated wastes were paralyzed or dried at optimal conditions and than specimens contained various percentages of pyrolysis ash were prepared with lab. and pilot scale melters. Compressive strength for these specimens was measured to determine the maximum ash content in glass waste forms. (author). 27 refs., 88 figs.

  7. Vapor detection of trafficking of contraband money: A discussion of technical feasibility

    Energy Technology Data Exchange (ETDEWEB)

    Dietz, R.N.

    1996-02-01

    For every two pounds of cocaine smuggled into the US, drug traffikers are being forced to clandestinely ship three pounds of money back out for subsequent laundering. Based on tracer technology developed for validation of long-range atmospheric transport models and other commercial applications, it is shown that US currency can be tagged with a minute amount (about 1 ppm by weight of a bill) of perfluorocharbon tracer (PFT) material that is sufficient to last for about 30 years and yet provide a vapor emission rate suitable for detectability of modest caches of contraband money in vehicles at border crossings, on aircraft at international terminals, and in buildings. The cost of tagging is less than $5 per million bills; the taggant quantity should have no impact on the feel of a bill. The low emission rate would not allow detectability of usual amounts of money in typical scenarios, providing an essential degree of privacy, but extraordinary amounts would be detectable using specialized instrumentation and know-how not easily attainable but commercially in production; an example of sub-part-per-quadrillion detection of a proposed PFT taggant is demonstrated using a prototype commercial unit. An outline of a research and demonstration program to achieve this capability and details of the proposed tagging and detection procedures already indicate that the concept is technically feasible.

  8. Feasibility studies of safety assessment methods for programmable automation systems. Final report of the AVV project

    International Nuclear Information System (INIS)

    Haapanen, P.; Maskuniitty, M.; Pulkkinen, U.; Heikkinen, J.; Korhonen, J.; Tuulari, E.

    1995-10-01

    Feasibility studies of two different groups of methodologies for safety assessment of programmable automation systems has been executed at the Technical Research Centre of Finland (VTT). The studies concerned the dynamic testing methods and the fault tree (FT) and failure mode and effects analysis (FMEA) methods. In order to get real experience in the application of these methods, an experimental testing of two realistic pilot systems were executed and a FT/FMEA analysis of a programmable safety function accomplished. The purpose of the studies was not to assess the object systems, but to get experience in the application of methods and assess their potentials and development needs. (46 refs., 21 figs.)

  9. Feasibility study of technologies to aid in the diagnosis of nuclear plant transients

    International Nuclear Information System (INIS)

    Bertch, W.J.; Bray, M.A.; Esparza, V.; Fink, R.K.; Shepherd, J.C.; Venhuizen, J.R.

    1985-08-01

    A technical feasibility study was performed to identify and evaluate the various computerized techniques available to diagnose and identify nuclear power plant transients in support of improving operator response to emergencies. Five categories of methods were investigated: expert system technology, computerized alarm handling, data driven displays, estimation and failure detection, and fault tree/event tree techniques. Literature searches and personal contacts were used to obtain information on specific methods and their applications within these categories. A set of evaluation criteria was established and an Analytic Hierarchy Process evaluation of the methods was performed. An integrated approach for a computerized operator aid, combining the strong features from the various methods, appears to be the most promising. 91 refs., 1 tab

  10. Mescalero Apache Tribe Monitored Retrievable Storage (MRS). Phase 1 feasibility study report

    Energy Technology Data Exchange (ETDEWEB)

    Peso, F.

    1992-03-13

    The Nuclear Waste Policy Act of 1982, as amended, authorizes the siting, construction and operation of a Monitored Retrievable Storage (MRS) facility. The MRS is intended to be used for the temporary storage of spent nuclear fuel from the nation`s nuclear power plants beginning as early as 1998. Pursuant to the Nuclear Waste Policy Act, the Office of the Nuclear Waste Negotiator was created. On October 7, 1991, the Nuclear Waste Negotiator invited the governors of states and the Presidents of Indian tribes to apply for government grants in order to conduct a study to assess under what conditions, if any, they might consider hosting an MRS facility. Pursuant to this invitation, on October 11, 1991 the Mescalero Apache Indian Tribe of Mescalero, NM applied for a grant to conduct a phased, preliminary study of the safety, technical, political, environmental, social and economic feasibility of hosting an MRS. The preliminary study included: (1) An investigative education process to facilitate the Tribe`s comprehensive understanding of the safety, environmental, technical, social, political, and economic aspects of hosting an MRS, and; (2) The development of an extensive program that is enabling the Tribe, in collaboration with the Negotiator, to reach an informed and carefully researched decision regarding the conditions, (if any), under which further pursuit of the MRS would be considered. The Phase 1 grant application enabled the Tribe to begin the initial activities necessary to determine whether further consideration is warranted for hosting the MRS facility. The Tribe intends to pursue continued study of the MRS in order to meet the following objectives: (1) Continuing the education process towards a comprehensive understanding of the safety, environmental, technical, social and economic aspects of the MRS; (2) Conducting an effective public participation and information program; (3) Participating in MRS meetings.

  11. High-dose-rate (HDR) brachytherapy after percutaneous coronary angioplasty (PTCA). Clinical pilot trial; feasibility study

    International Nuclear Information System (INIS)

    Popowski, Youri; Verin, Vitali; Urban, Philippe; Nouet, Philippe; Rouzaud, Michel; Schwager, Michaeel; Rutishauser, Wilhelm; Kurtz, John

    1996-01-01

    Introduction. With the aim of reducing the incidence of restenosis, we developed a technique of intracoronary beta irradiation using an enylenediamine centered pure metallic 90-yttrium source fixed to a thrust wire. The outer diameter of both the active and thrust wires is 0.34 mm. A centering balloon with a monorail design and a blind lumen for source advancement has been developed. The source can be advanced manually in 10-13'' from the protection container to the target site. Its flexibility allows easy insertion despite tortuous anatomy. Dosimetric tests have been performed with 2.5, 3, 3.5 and 4 mm centering balloons. The standard deviation values varied between 8 and 12 % of the mean surface doses, which confirms the efficacy of the source centering. The purpose of this study was to evaluate its technical feasibility and short-term safety in the clinical setting. Methods and results. Between June 21 and November 15, 1995 fifteen patients (6 women and 9 men, aged 72 ± 5 years) underwent intracoronary beta irradiation immediately after a conventional percutaneous transluminal coronary angioplasty (P TCA) procedure. Both the PTCA and the irradiation procedure were done in an ordinary catheterization laboratory. They were technically feasible in all cases, and the delivery of the 18 Gy dose was accomplished within a local exposure time 391 ± 206 sec (range 153 - 768 sec) without any complication. In four patients, the intervention was completed by intraarterial stent implantation because of dissection induced by the initial PTCA. No in-hospital complications occurred, and serial creatine kinase measurements remained within the normal range in all cases. During a follow-up period of 54±46 days (range 20 days - 5 months) all patients remained well and free of cardiac events. Conclusions. Our early experience thus suggests that this approach is both feasible and safe on a short-term basis. Whether beta-irradiation will favorably influence post PTCA restenosis in

  12. Feasibility of the recent Russian nuclear electric propulsion concept: 2010

    International Nuclear Information System (INIS)

    Zakirov, Vadim; Pavshook, Vladimir

    2011-01-01

    Highlights: → The paper focuses on feasibility of the Russian nuclear electric propulsion (NEP) concept. → The Russian NEP concept is based on the past experience and is, therefore, technically feasible. → The big concern is that the program will be cancelled due to non-technical issues. - Abstract: The paper introduces recent Russian nuclear electric propulsion (NEP) concept for space exploration. The concept advantages are listed along with future missions. The current development status for the two main enabling technologies is presented and the feasibility analysis of the up-to-date experience is performed. The main features of NEP concept are discussed. Revision of these features and available technologies demonstrates that the NEP concept is a logical continuation of the previous efforts by the former Soviet Union. Because no breakthrough technologies are needed for NEP development while the existing technologies only need to be adapted to the megawatt (MW) class NEP the development is considered technically feasible, low risk program likely to succeed unless cancelled by the listed non-technical reasons. Successful NEP space vehicle development is going to bring practical space exploration of solar system to the new level as well as require supplementary payload program, supporting monitoring and communication radar networks. Nuclear safety during future NEP missions can be ensured by adherence to the United Nations guidelines in the same way it was done during the Soviet Topaz Nuclear Power System (NPS) missions.

  13. Feasibility of the recent Russian nuclear electric propulsion concept: 2010

    Energy Technology Data Exchange (ETDEWEB)

    Zakirov, Vadim, E-mail: v.zakirov@mail.tsinghua.edu.c [Room 3121, Yifu Building, School of Aerospace, Tsinghua University, Haidian District, Beijing 100084 (China); Pavshook, Vladimir, E-mail: vap_ki@mail.r [Russian Research Center ' Kurchatov Institute' , Kurchatov Sq. 1, Moscow 123182 (Russian Federation)

    2011-05-15

    Highlights: The paper focuses on feasibility of the Russian nuclear electric propulsion (NEP) concept. The Russian NEP concept is based on the past experience and is, therefore, technically feasible. The big concern is that the program will be cancelled due to non-technical issues. - Abstract: The paper introduces recent Russian nuclear electric propulsion (NEP) concept for space exploration. The concept advantages are listed along with future missions. The current development status for the two main enabling technologies is presented and the feasibility analysis of the up-to-date experience is performed. The main features of NEP concept are discussed. Revision of these features and available technologies demonstrates that the NEP concept is a logical continuation of the previous efforts by the former Soviet Union. Because no breakthrough technologies are needed for NEP development while the existing technologies only need to be adapted to the megawatt (MW) class NEP the development is considered technically feasible, low risk program likely to succeed unless cancelled by the listed non-technical reasons. Successful NEP space vehicle development is going to bring practical space exploration of solar system to the new level as well as require supplementary payload program, supporting monitoring and communication radar networks. Nuclear safety during future NEP missions can be ensured by adherence to the United Nations guidelines in the same way it was done during the Soviet Topaz Nuclear Power System (NPS) missions.

  14. Creation of the First French Database in Primary Care Using the ICPC2: Feasibility Study.

    Science.gov (United States)

    Lacroix-Hugues, V; Darmon, D; Pradier, C; Staccini, P

    2017-01-01

    The objective of our study was to assess the feasibility of gathering data stored in primary care Electronic Health records (EHRs) in order to create a research database (PRIMEGE PACA project). The software for EHR models of two office and patient data management systems were analyzed; anonymized data was extracted and imported into a MySQL database. An ETL procedure to code text in ICPC2 codes was implemented. Eleven general practitioners (GPs) were enrolled as "data producers" and data were extracted from 2012 to 2015. In this paper, we explain the ways to make this process feasible as well as illustrate its utility for estimating epidemiological indicators and professional practice assessments. Other software is currently being analyzed for integration and expansion of this panel of GPs. This experimentation is recognized as a robust framework and is considered to be the technical foundation of the first regional observatory of primary care data.

  15. Feasibility of evacuation

    International Nuclear Information System (INIS)

    1988-01-01

    The main question is whether evacuation of people is feasible in case of accidents with a nuclear power plant. The limiting conditions of this question are extracted from other studies. This study is therefore focused on a postulated accident in a newly built nuclear power plant with an electric capacity of 1000 Megawatt and a source term of one percent. In this particular case an evacuation should take place within the period between the accident and the emission of nuclear materials. Initial focus is on the administrative-organizational aspects of evacuation. Then bottlenecks in the technical implementation of evacuation are determined. An analysis is made for each potential Dutch location (Borssele, Eemshaven, Maasvlakte, Moerdijk and Westelijke Noordoostpolderdijk) of a nuclear power plant. By means of a model the following question is examined: can the population leave the danger area or be evacuated on time, under certain circumstances. It is concluded that preventive evacuation of the population from the planned locations is feasible, but at Moerdijk complications may occur because of the presence of some homes for the elderly and a nursing home. 18 refs.; 7 figs.; 2 tabs

  16. Using multidetector-row CT in neonates with complex congenital heart disease to replace diagnostic cardiac catheterization for anatomical investigation: initial experiences in technical and clinical feasibility

    International Nuclear Information System (INIS)

    Lee, Tain; Tsai, I.C.; Chen, Min-Chi; Fu, Yun-Ching; Jan, Sheng-Lin; Wang, Chung-Chi; Chang, Yen

    2006-01-01

    Echocardiography is the first-line modality for the investigation of neonatal congenital heart disease. Diagnostic cardiac catheterization, which has a small but recognized risk, is usually performed if echocardiography fails to provide a confident evaluation of the lesions. To verify the technical and clinical feasibilities of replacing diagnostic cardiac catheterization with multidetector-row CT (MDCT) in neonatal complex congenital heart disease. Over a 1-year period we prospectively enrolled all neonates with complex congenital heart disease referred for diagnostic cardiac catheterization after initial assessment by echocardiography. MDCT was performed using a 40-detector-row CT scanner with dual syringe injection. A multidisciplinary congenital heart disease team evaluated the MDCT images and decided if further diagnostic cardiac catheterization was necessary. The accuracy of MDCT in detecting separate cardiovascular anomalies and bolus geometry of contrast enhancement were calculated. A total of 14 neonates were included in the study. No further diagnostic cardiac catheterization was needed in any neonate. The accuracy of MDCT in diagnosing separate cardiovascular anomalies was 98% (53/54) with only one atrial septal defect missed in a patient with coarctation syndrome. The average cardiovascular enhancement in evaluated chambers was 471 HU. No obvious beam-hardening artefact was observed. The technical and clinical feasibility of MDCT in complex congenital heart disease in neonates is confirmed. After initial assessment with echocardiography, MDCT could probably replace diagnostic cardiac catheterization for further anatomical clarification in neonates. (orig.)

  17. Spirometry in elderly laryngectomized patients: A feasibility study.

    Science.gov (United States)

    Izzo, Alessandro; Perrotta, Fabio; Cennamo, Antonio; Cerqua, Francesco Saverio; Rinaldi, Luca; Mazzella, Antonio; Grella, Edoardo; Tranfa, Carmelindo; Bianco, Andrea; Stefanelli, Francesco; Mazzarella, Gennaro

    2016-09-01

    Laryngeal cancer is the second most common respiratory neoplasm after lung cancer. Laryngectomy is a well established treatment for larynx cancers which involve relevant anatomic alterations. Spirometry is an essential investigation tool for diagnosis and severity of respiratory diseases, difficult to perform in laryngectomees. 43 consecutive laryngectomized patients were enrolled from July 2014 to March 2015. Patients fulfilling inclusion criteria underwent spirometry at baseline assessment and after two days. During the examination, the spirometer was placed directly on the stoma of the patient, through mouthpiece "Spirometry Filter 74". At baseline, 26 eligible laryngectomees correctly performed the spirometry test with mouthpiece adhering to the stoma; 4 patients refused to perform the second spirometry after 2 days. The feasibility of spirometry examination in these patients was 100% despite difficulties in the execution of the test. The Pearson coefficient of reproducibility for FEV1, FVC and Tiffeneau Index was, respectively, 0.98, 0.94 and 0.77. Spirometry in laryngectomee patients is a feasible procedure for assessment of respiratory function; despite technical difficulties in the execution of the test, our results underline the reproducibility and repeatability of the spirometry. In conclusion, when performed within dedicated respiratory pathophysiology unit, spirometry is a reliable tool in the assessment and follow up of laryngectomees. Copyright © 2016 IJS Publishing Group Ltd. Published by Elsevier Ltd. All rights reserved.

  18. Revised CTUIR Renewable Energy Feasibility Study Final Report

    Energy Technology Data Exchange (ETDEWEB)

    John Cox; Thomas Bailor; Theodore Repasky; Lisa Breckenridge

    2005-10-31

    This preliminary assessment of renewable energy resources on the Umatilla Indian Reservation (UIR) has been performed by CTUIR Department of Science and Engineering (DOSE). This analysis focused primarily identifying renewable resources that may be applied on or near the Umatilla Indian Reservation. In addition preliminary technical and economic feasibility of developing renewable energy resources have been prepared and initial land use planning issues identified. Renewable energies examined in the course of the investigation included solar thermal, solar photovoltaic, wind, bioethanol, bio-diesel and bio-pellet fuel. All renewable energy options studied were found to have some potential for the CTUIR. These renewable energy options are environmentally friendly, sustainable, and compliment many of the policy goals of the CTUIR. This report seeks to provide an overall review of renewable energy technologies and applications. It tries to identify existing projects near to the CTUIR and the efforts of the federal government, state government and the private sector in the renewable energy arena. It seeks to provide an understanding of the CTUIR as an energy entity. This report intends to provide general information to assist tribal leadership in making decisions related to energy, specifically renewable energy deve lopment.

  19. Fort Yukon, Chalkyitsik, & Venetie Biomass Boiler Feasibility Study

    Energy Technology Data Exchange (ETDEWEB)

    Greg Koontz, ME William A. Wall, PhD

    2009-03-31

    The Council of Athabascan Tribal Governments (CATG) is a consortium of ten Gwich'in and Koyukon Athabascan tribes settled in 10 remote villages and are linked by the Yukon River System. The CATG mission is to maintain the Yukon Flats region as Indian Country by asserting traditional rights and taking responsibility for developing tribal technical capacity to manage the land and resources. It is the intent of CATG to explore and develop all opportunities for a renewable and self-sufficient energy program for each of the villages. CATG envisions utilization of forest resources both for construction and energy as one of the best long-term strategies for integrating the economic goals for the region as well as supporting the cultural and social issues. The intent for this feasibility project is to focus specifically on biomass utilization for heat, first, and for future electrical generation within the region, second. An initial determination has already been made regarding the importance of wood energy as a primary source of renewable energy to displace diesel fuel in the Yukon Flats region. A desktop study of other potential renewable resources was conducted in 2006.

  20. Feasibility study on the introduction of hybrid buses; Hybrid bus donyu kanosei chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The purpose of this research is to design pilot projects for introducing hybrid buses into the public transportation sector. This research also covers contents regarding hybrid buses with a trolley-collector motor and a diesel engine, to identify technical and economical problems and to analyze cost beneficiation using hybrid buses. The trolley parallel hybrid system has been employed for the feasibility study. This system has abundant operation results in Europe and the USA. Its battery is small or is not necessary, and the maintenance cost is also low. As a result of the feasibility study, reduction effects of CO2 emission were found out. When the CO2 generation at the power plant is not counted, the reduction effect was estimated to be 32% compared with the CO2 emission from diesel buses. When the CO2 generation at the power plant is considered, it was estimated to be 18%. The cost beneficiation was investigated for the cases of the transportations using trolley system surrounding a medium-scale terminal among large-scale housing development, tourist resort, and stations. The annual income is estimated to be larger than the annual payment in each case. It was found that the hybrid bus is economically established. 17 refs., 48 figs., 41 tabs.

  1. Technical and economic feasibility study of flue gas injection in an Iranian oil field

    Directory of Open Access Journals (Sweden)

    Mohammad Ali Ahmadi

    2015-09-01

    The main aim of this research is to investigate various gas injection methods (N2, CO2, produced reservoir gas, and flue gas in one of the northern Persian gulf oil fields by a numerical simulation method. Moreover, for each scenario of gas injection technical and economical considerations are took into account. Finally, an economic analysis is implemented to compare the net present value (NPV of the different gas injection scenarios in the aforementioned oil field.

  2. Feasibility study of local ultrasound hyperthermia in cancer therapy

    International Nuclear Information System (INIS)

    Jones, K.G.; Straube, W.; Emami, B.; Perez, C.A.

    1987-01-01

    This paper describes a retrospective analysis of patients treated at Washington University for recurrent or persistent cancer with Ultrasound Hyperthermia between October 1984 and June 1986. Fifteen of 102 lesions were treated during this time period with Ultrasound Hyperthermia instead of microwave hyperthermia due to the size of the lesion needing heat at depths greater than 4 cm. Also, the patients' lesion could not be implanted for interstitial microwave hyperthermia. Fourteen of the treated patients received concomitant radiotherapy, while one received concomitant Bleomycin. There were 79 total hyperthermia treatments delivered, of which 67 achieved a therapeutic temperature of 43 0 C for 60 minutes. During 15/79 treatments, patients experienced pain; of which 11/15 lead to poor heating. Only one treatment of the twelve poor treatments was secondary to technical difficulties. Complete local control was accomplished in seven patients, a partial response in four patients. The results of therapeutic heating and its relationship to the site of treatment and local control are presented, along with phantom studies of Ultrasound microwave hyperthermia reemphasizing the feasibility of using Ultrasound Hyperthermia

  3. Feasibility Study for Renewable Energy Development on Tribal Lands

    Energy Technology Data Exchange (ETDEWEB)

    John Hendrix, Project Director; Charles Weir, Project Manager; Dr. John Plodinec, Technology Advisor; Dr. Steve Murray, Economic Advisor

    2005-07-21

    Project Objective: The Mississippi Band of Choctaw Indians (MBCI) conducted a study of the feasibility of siting a renewable energy biomass-based installation on tribal lands. The purpose of the study was to determine whether such an installation can be economically sustainable, as well as consistent with the cultural, social, and economic goals of the Tribe. Scope: To achieve the goal of the feasibility study, the following tasks were carried out: (1) Resource availability assessment--The objective of this assessment was to determine the availability of both poultry litter and wood residues for use in the proposed facility. (2) Power utilization assessment--The objective of this assessment was to determine the potential market size for power produced, the existing infrastructure for delivering power to that market, and the costs and economic returns for doing so. (3) Technology review--The objective of this review was to identify one, or more, technical options for detailed economic and technical assessment. The study considered a range of feedstock and product mixtures of poultry litter; wood residues as feedstock; and electrical power and other ancillary products as outputs. Distributed power sources was also examined. Technologies ranging from gasification to systems that produce both power and value-added chemicals were considered. Technologies selected for detailed review were those that can be sized to process the amount of available feed (poultry litter, or poultry litter and wood residues), and that also appear to make economic sense in terms of the value of their inputs. The technology review leaned heavily on the experience from similar prior DOE projects, particularly those conducted by the National Renewable Energy Laboratory (NREL). NREL was involved in a consultative role, so that the project team could leverage their experience. (4) Systems Design(s)--Based on the technology review, a pre-conceptual design for an installation was developed. This

  4. Feasibility study of plutonium recycling in light water reactors

    International Nuclear Information System (INIS)

    Tabuchi, Hideoto

    1979-01-01

    The feasibility of plutonium recycling in light water reactors has been studied by the Agency of Natural Resources and Energy, MITI. As the first step of the feasibility study, it was planned to charge two fuel assemblies, containing uranium-plutonium mixed oxide (MO 2 ), in the core of the Tsuruga nuclear power plant (BWR) for testing. The design of fuel the safety of these fuel and the operating characteristics of these special fuel assemblies were evaluated. The specifications of MO 2 fuel pin and fuel assembly are compared to those of present uranium oxide (UO 2 ) fuel. The weight of fissile plutonium in one MO 2 fuel assembly is 2.22 kg. The characteristics of MO 2 fuel assemblies, such as reactivity, control rod worth and power distribution can be kept similar to UO 2 fuel. The plutonium isotope ratio of the MO 2 fuel is assumed as that obtained in the fuel taken out of the Tokai No. 1 gas cooled reactor. The temperature distribution in the fuel pellets is shown, compared to that of UO 2 fuel. The linear power density is 440 w/cm at the beginning of the fuel life and 360 w/cm after the burn-up of 44,000 Mwd/t. The stress in the cladding tubes of MO 2 fuel is not different from that of UO 2 fuel. The pellet-cladding interaction (PCM1) was analyzed, utilizing the FEM code, FEAST. Concerning the calculation of resonance absorption, the space dependence of thermal neutron spectra and the nuclear behavior of hollow pellets the methods of design calculation were checked up. It was recognized that regarding the nuclear characteristics of MO 2 fuel, no special technical question remains. (Nakai, Y.)

  5. Human reliability data bank: feasibility study

    International Nuclear Information System (INIS)

    Comer, K.; Miller, D.P.; Donovan, M.

    1984-01-01

    The US Nuclear Regulatory Commission and Sandia National Laboratories have been developing a plan for a human reliability data bank since August 1981. This research is in response to the data needs of the nuclear power industry's probabilistic risk assessment community. The three phases of the program are to: (A) develop the data bank concept, (B) develop an implementation plan and conduct a feasibility study, and (C) assist a sponsor in implementing the data bank. The program is now in Phase B. This paper describes the methods used in the feasibility study. Decisions to be made in the future regarding full-scale implementation will be based, in part, on the outcome of this study. 3 references, 2 figures

  6. Safety Improvements on Wood Chippers Currently in Use: A Study on Feasibility in the Italian Context

    Directory of Open Access Journals (Sweden)

    Giorgia Bagagiolo

    2017-12-01

    Full Text Available Following formal opposition by France, the harmonized safety standards regarding manually-loaded wood chippers (EN 13525:2005+A2:2009 which presumed compliance with the Essential Health and Safety Requirements (EHSR required by the Machine Directive (Directive 2006/42/EC, have recently been withdrawn, and a new draft of the standard is currently under revision. In order to assess the potential impact of the expected future harmonized standards within the Italian context, this study has examined the main issues in implementing EHSRs on wood chippers already being used. Safety issues regarding wood chippers already in use were identified in an analysis of the draft standard, through the observation of a number of case studies, and qualitative analysis of the essential technical interventions. A number of agricultural and forestry operators and companies participated in the study, pointing out the technical and economic obstacle facing the safety features requested by the pending new standard. It emerged that the main safety issues concerned the implementation of the reverse function, the stop bar, and the protective devices, the infeed chute dimension, the emergency stop function, and the designated feeding area. The possibility of adopting such solutions mainly depends on technical feasibility and costs, but an important role is also played by the attitude towards safety and a lack of adequate information regarding safety obligations and procedures among users.

  7. Feasibility study on the use of waste heat in mushroom cultivation; Haalbaarheid benutting restwarmte in de paddenstoelenteelt

    Energy Technology Data Exchange (ETDEWEB)

    Gielen, J.H. [DLV Plant, Horst (Netherlands)

    2011-03-15

    This study has examined the technical as well as the economic feasibility of waste heat utilization in a standard cultivation business [Dutch] In dit onderzoek zijn zowel de technische als ook de economische haalbaarheid van toepassingen voor het hergebruik van restwarmte in een standaard teeltbedrijf onderzocht. Gebruikte informatiebronnen voor dit onderzoek waren praktijkervaringen, literatuur en ontwikkelingen in andere sectoren. Behalve de mogelijkheden in de huidige teeltsystemen zijn er mogelijk ook toepassingen denkbaar in de recente ontwikkelingen op het vlak van bedkoeling en bedverwarming. In een dergelijk systeem zal laagwaardige warmte naar verwachting makkelijker inzetbaar zijn.

  8. Techno-economical analysis of innovative technologies in electrical power systems. A feasibility study for a Russian distribution system operator

    International Nuclear Information System (INIS)

    Mueller, Holger; Nikitina, Elena; Makarov, Andrej

    2015-01-01

    Since the liberalization of the energy market in Europe transmission and distribution system operators have been facing fundamentally new challenges when ensuring a safe and reliable power supply. In addition to purely technical criteria economical aspects have become increasingly important in the strategic planning and operation of power systems. As described in this contribution, the results of a feasibility study demonstrate how the use of innovative technologies can make a valuable contribution to improve the economical situation.

  9. Thermal exploitation of shallow aquifers. Guide for the preparation of preliminary studies of technical feasibility

    International Nuclear Information System (INIS)

    Ausseur, J.Y.; Sauty, J.P.

    1982-08-01

    This report presents the main devices aimed at exploiting surface aquifers. After an introduction to the different systems of thermal exploitation of aquifers (generalities, very low energy geothermal, sensitive heat storage, interest of thermal exploitation of aquifers, indication of possible systems), this report presents the different possible systems and analyses their characteristics and performance. These systems are: direct exploitation of groundwater bodies at their natural temperature by heat sink and with release in surface networks or by geothermal dipole, or exploitation with artificial thermal refill. Thus the report addresses the single sink device with or without storage, heat pumps on dipole in surface groundwater bodies or very low temperature geothermal, the scanning dipole system, and the dipole system with hot sink and cold sink. It discusses the choice and sizing of the exploitation system. An appendix reports a feasibility preliminary study of nine cases of thermal exploitation of surface aquifers by double drills

  10. Simulation-based ureteroscopy skills training curriculum with integration of technical and non-technical skills: a randomised controlled trial.

    Science.gov (United States)

    Brunckhorst, Oliver; Shahid, Shahab; Aydin, Abdullatif; McIlhenny, Craig; Khan, Shahid; Raza, Syed Johar; Sahai, Arun; Brewin, James; Bello, Fernando; Kneebone, Roger; Khan, Muhammad Shamim; Dasgupta, Prokar; Ahmed, Kamran

    2015-09-01

    Current training modalities within ureteroscopy have been extensively validated and must now be integrated within a comprehensive curriculum. Additionally, non-technical skills often cause surgical error and little research has been conducted to combine this with technical skills teaching. This study therefore aimed to develop and validate a curriculum for semi-rigid ureteroscopy, integrating both technical and non-technical skills teaching within the programme. Delphi methodology was utilised for curriculum development and content validation, with a randomised trial then conducted (n = 32) for curriculum evaluation. The developed curriculum consisted of four modules; initially developing basic technical skills and subsequently integrating non-technical skills teaching. Sixteen participants underwent the simulation-based curriculum and were subsequently assessed, together with the control cohort (n = 16) within a full immersion environment. Both technical (Time to completion, OSATS and a task specific checklist) and non-technical (NOTSS) outcome measures were recorded with parametric and non-parametric analyses used depending on the distribution of our data as evaluated by a Shapiro-Wilk test. Improvements within the intervention cohort demonstrated educational value across all technical and non-technical parameters recorded, including time to completion (p technical and non-technical skills teaching is both educationally valuable and feasible. Additionally, the curriculum offers a validated simulation-based training modality within ureteroscopy and a framework for the development of other simulation-based programmes.

  11. Feasibility and Pilot Studies in Palliative Care Research: A Systematic Review.

    Science.gov (United States)

    Jones, Terry A; Olds, Timothy S; Currow, David C; Williams, Marie T

    2017-07-01

    Feasibility and pilot study designs are common in palliative care research. Finding standard guidelines on the structure and reporting of these study types is difficult. In feasibility and pilot studies in palliative care research, to determine 1) how commonly a priori feasibility are criteria reported and whether results are subsequently reported against these criteria? and 2) how commonly are participants' views on acceptability of burden of the study protocol assessed? Four databases (OVID Medline, EMBASE, CINAHL, and PubMed via caresearch.com.au.) were searched. Search terms included palliative care, terminal care, advance care planning, hospice, pilot, feasibility, with a publication date between January 1, 2012 and December 31, 2013. Articles were selected and appraised by two independent reviewers. Fifty-six feasibility and/or pilot studies were included in this review. Only three studies had clear a priori criteria to measure success. Sixteen studies reported participant acceptability or burden with measures. Forty-eight studies concluded feasibility. The terms "feasibility" and "pilot" are used synonymously in palliative care research when describing studies that test for feasibility. Few studies in palliative care research outline clear criteria for success. The assessment of participant acceptability and burden is uncommon. A gold standard for feasibility study design in palliative care research that includes both clear criteria for success and testing of the study protocol for participant acceptability and burden is needed. Such a standard would assist with consistency in the design, conduct and reporting of feasibility and pilot studies. Copyright © 2017 American Academy of Hospice and Palliative Medicine. Published by Elsevier Inc. All rights reserved.

  12. Technical/economical analysis of bioenergy systems

    International Nuclear Information System (INIS)

    Solantausta, Y.

    1998-01-01

    The objectives of the IEA Bioenergy Technoeconomic Analysis Activity are: (1) To promote development of thermochemical biomass conversion methods by carrying out selected site specific feasibility studies in participating countries. Both agricultural and woody biomasses will be converted either into electricity or boiler fuels; (2) To compare advanced technologies to commercial alternatives based on technoeconomic basis to establish future development needs, and (3) To facilitate information exchange between participants on relevant basic process issues. Five countries (Finland, Canada, USA, Norway, Austria) are participating to the Activity. Initially two feasibility studies are planned for each country. Each study has three common elements: site specific, technical, and economic data. The site specific cases are described below in short. Products in the cases are electricity, heat and fuel oil. Total of two cases per country are planned. (orig.)

  13. Feasibility study for fast reactor and related fuel cycle. Preliminary studies in 1998

    International Nuclear Information System (INIS)

    Hayafune, Hiroki; Enuma, Yasuhiro; Kubota, Kenichi; Yoshida, Masashi; Uno, Osamu; Ishikawa, Hiroyasu; Kobayashi, Jun; Umetsu, Youichiro; Ichimiya, Masakazu

    1999-10-01

    Prior to the feasibility study for fast reactors (FRs) starting from the 1999 fiscal year, planned in the medium and long-term program of JNC, preliminarily studies were performed on 'FR systems except sodium cooled MOX fueled reactors'. Small scale or module type reactors, heavy metal (Pb or Pb-Bi) cooled reactors, gas cooled reactors, light water cooled reactors, and molten salt reactors were studied on the basis of literature. They were evaluated from the viewpoint of the technical possibility (the structure integrity, earthquake resistance, safety, productivity, operability, maintenance repair, difficulty of the development), the long-term targets (market competitiveness as an energy system, utilization of uranium resources, reduction of radioactive waste, security of the non-proliferation), and developmental risk. As the result, the following concepts should be studied for future commercialized FRs. Small scale and module type reactor: Middle-sized reactor with an excellent economical efficiency. Small power reactor with a multipurpose design concept. Gas cooled reactor: CO2 gas cooled reactor, He gas cooled reactor. Heavy metal cooled reactor: Russian type lead cooled reactor. Light water cooled reactor: Light water cooled high converter reactor and super critical pressure light water cooled reactor. Molten salt reactor: Trichloride molten salt reactor which matches the U-Pu cycle. (author)

  14. Technical feasibility study of Voltage Optimization Unit

    DEFF Research Database (Denmark)

    Hu, Junjie; Marinelli, Mattia; Coppo, Massimiliano

    This report provides an analysis on the benefits of a transformer with on load tap chang-ers on each phase that can be applied in the distribution system to accommodate more renewable generations such as photovoltaic power. The main purpose of this research is to verify whether power distribution...... are used as load basics for the analysis. In term of PV genera-tion profiles, a realistic PV output power is assumed. Four relevant indicies such as phase neutral voltage, netural potential voltage, unbalanced factor (VUF), and power losses are evaluated in the present study. The simulation tests include...

  15. Beyond xMOOCs in healthcare education: study of the feasibility in integrating virtual patient systems and MOOC platforms.

    Science.gov (United States)

    Stathakarou, Natalia; Zary, Nabil; Kononowicz, Andrzej A

    2014-01-01

    Background. Massive Open Online Courses (MOOCs) are an emerging trend in online learning. However, their technology is not yet completely adjusted to the needs of healthcare education. Integration of Virtual Patients within MOOCs to increase interactivity and foster clinical reasoning skills training, has been discussed in the past, but not verified by a practical implementation. Objective. To investigate the technical feasibility of integrating MOOCs with Virtual Patients for the purpose of enabling further research into the potential pedagogical benefits of this approach. Methods. We selected OpenEdx and Open Labyrinth as representative constituents of a MOOC platform and Virtual Patient system integration. Based upon our prior experience we selected the most fundamental technical requirement to address. Grounded in the available literature we identified an e-learning standard to guide the integration. We attempted to demonstrate the feasibility of the integration by designing a "proof-of-concept" prototype. The resulting pilot implementation was subject of verification by two test cases. Results. A Single Sign-On mechanism connecting Open Labyrinth with OpenEdx and based on the IMS LTI standard was successfully implemented and verified. Conclusion. We investigated the technical perspective of integrating Virtual Patients with MOOCs. By addressing this crucial technical requirement we set a base for future research on the educational benefits of using virtual patients in MOOCs. This provides new opportunities for integrating specialized software in healthcare education at massive scale.

  16. Beyond xMOOCs in healthcare education: study of the feasibility in integrating virtual patient systems and MOOC platforms

    Directory of Open Access Journals (Sweden)

    Natalia Stathakarou

    2014-11-01

    Full Text Available Background. Massive Open Online Courses (MOOCs are an emerging trend in online learning. However, their technology is not yet completely adjusted to the needs of healthcare education. Integration of Virtual Patients within MOOCs to increase interactivity and foster clinical reasoning skills training, has been discussed in the past, but not verified by a practical implementation.Objective. To investigate the technical feasibility of integrating MOOCs with Virtual Patients for the purpose of enabling further research into the potential pedagogical benefits of this approach.Methods. We selected OpenEdx and Open Labyrinth as representative constituents of a MOOC platform and Virtual Patient system integration. Based upon our prior experience we selected the most fundamental technical requirement to address. Grounded in the available literature we identified an e-learning standard to guide the integration. We attempted to demonstrate the feasibility of the integration by designing a “proof-of-concept” prototype. The resulting pilot implementation was subject of verification by two test cases.Results. A Single Sign-On mechanism connecting Open Labyrinth with OpenEdx and based on the IMS LTI standard was successfully implemented and verified.Conclusion. We investigated the technical perspective of integrating Virtual Patients with MOOCs. By addressing this crucial technical requirement we set a base for future research on the educational benefits of using virtual patients in MOOCs. This provides new opportunities for integrating specialized software in healthcare education at massive scale.

  17. VIRTUAL PHILOSOPHER PROJECT: PHILOSOPHICAL, PEDAGOGICAL AND TECHNICAL ASPECTS

    Directory of Open Access Journals (Sweden)

    E. V. Kuchinov

    2017-01-01

    Full Text Available The article describes philosophical and pedagogical aspects of an idea of the ‘virtual philosopher’ project developed at creative sessions at Minin University and technically concretized during interaction with the Laboratory of Mobile Services. ‘Virtual philosopher’ is thought to deliver creative automation of routine operations; producing contingent matter for philosophical processing as well as elements of the philosophical artificial intelligence and forms of ‘artificial life’. Project implementation may lead to the creation of an unparalleled educational technology that functions on the principles of flexibility, nonlinearity, affective inclusion and gamification of the educational process. Based on specific character of problems raised, rhizomatic analysis of the philosophical communities’ requests, assessment of their technical feasibility and technical development, provisions are made on the feasibility, prospects and productivity of this project.

  18. Technical feasibility study for the electrochemical treatment of Phaeozem soil contaminated with radioactive organic liquids

    International Nuclear Information System (INIS)

    Valdovinos G, V.

    2014-01-01

    The application of radioisotopes in medicine and research generates radioactive waste. A large part of these wastes are composed by scintillation liquid (mixtures of organic solvents, as toluene and xylene, fluorescent materials and surfactants) contaminated with radioisotopes such as 3 H (12.3 y), 14 C (5730 y), 238 U (4.468 x 10 9 y), 232 Th (1.41 x 10 10 y), 204 Tl (3.7 y) or 22 Na (2.6 y). In Mexico during the 80 s, these wastes were absorbed on soil to decrease their hazardous behavior during interim storage. However, these wastes must be removed for reprocessing and final landscaping. Therefore, the objective of this thesis is to study the technical feasibility of the electrochemical treatment of soils types Phaeozem contaminated with radioactive organic liquid waste (ROLW). For this study, an electrochemical treatment at laboratory level was applied, giving it an electrokinetic tracking. Control samples were prepared with different scintillation liquid (INSTAL Gel- XF, ULTIMA Gold AB TM and ULTIMA Gold XR TM as support electrolyte and polarization curves were constructed to select the current with the highest mass transfer. An analysis of the liquids and solids, before and after the application of the different potentials; the liquid phase was characterized by Gas Chromatography coupled with Flame Ionized Detector (GC-FID) and Fourier Transform Infrared Spectrometry (Ft-Irs), and the solids by Ft-Irs. From the fourteen supports electrolytes studied, eleven did not have a stable diffusion current and the other three showed a diffusion current plateau in 0.02, 0.04 and 0.06 m A·cm -2 . From polarization curves, the following experimental conditions were chosen for the treatment: electrodes (meshes of titanium as anode and rod of stainless steel as cathode), scintillation liquid (ULTIMA Gold XR TM : water, 1:1) and a current of 0.06 m A·cm -2 . Subsequently, radioactive control samples were prepared with soil-scintillation liquid, labeled with 24 Na, 99m Tc

  19. Feasibility Study on Dual-Cooled Annular Fuel for OPR-1000 Power Uprate

    International Nuclear Information System (INIS)

    Chun, Tae Hyun; In, Wang Kee; Oh, Dong Suck

    2010-04-01

    A dual-cooled annular fuel (DCAF) is a highly promising concept as a high power density fuel for PWR power-uprate. The purpose of this study is to assess a feasibility of 120% core power for OPR-1000 with the DCAF. So the feasibility study were done through the code establishments for annular fuel analysis, evaluations of core physics, thermal-hydraulics and safety analyses at a 120% power with OPR-1000 and the preliminary economic benefits of 20% power-uprate. As results of the analyses, DCAF at 120% power showed sufficient margins available on DNB, PCT and fuel pellet temperature relative to the solid fuel at 100% power. However, judging from an anticipated wide range of the gap conductance variation in inner and outer clearances as fuel burn-up in the reactor core, irradiation behavior of DCAF has to be observed through research reactor test. On the other hand, the nuclear physics parameters like moderator temperature coefficient, power coefficient and so on comply with the technical specifications. An impact of 20% power-uprate on NSSS and BOP was also investigated, and accordingly some components and parts need to be changed were identified. Moreover, the economical benefits from the power-uprate was roughly estimated. It turned out that the power-uprating with DCAF could give an enormous profit even considering the expenses of components and parts to be replaced, additional fuel cycle cost and extended overhaul period

  20. Technical and economic feasibility study of enhanced oil recovery in six Colombian fields. Appendix C. Export trade information

    Energy Technology Data Exchange (ETDEWEB)

    1986-09-01

    The primary objectives of the study were to determine which of the reservoirs in the principal fields were amenable to enhanced oil recovery (EOR) processes, to evaluate which process was the most effective from both a technical and economic point of view, and to propose the steps required to further investigate the recommended EOR methods at the laboratory and field (pilot) level. Appendix C is divided into three sections: (A) Casabe Field; (B) La Cira Field; and (C) Tibu-Barco.

  1. Vessel Cold-Ironing Using a Barge Mounted PEM Fuel Cell: Project Scoping and Feasibility.

    Energy Technology Data Exchange (ETDEWEB)

    Pratt, Joseph William [Sandia National Lab. (SNL-CA), Livermore, CA (United States); Harris, Aaron P. [Sandia National Lab. (SNL-CA), Livermore, CA (United States)

    2013-01-01

    A barge-mounted hydrogen-fueled proton exchange membrane (PEM) fuel cell system has the potential to reduce emissions and fossil fuel use of maritime vessels in and around ports. This study determines the technical feasibility of this concept and examines specific options on the U.S. West Coast for deployment practicality and potential for commercialization.The conceptual design of the system is found to be straightforward and technically feasible in several configurations corresponding to various power levels and run times.The most technically viable and commercially attractive deployment options were found to be powering container ships at berth at the Port of Tacoma and/or Seattle, powering tugs at anchorage near the Port of Oakland, and powering refrigerated containers on-board Hawaiian inter-island transport barges. Other attractive demonstration options were found at the Port of Seattle, the Suisun Bay Reserve Fleet, the California Maritime Academy, and an excursion vessel on the Ohio River.

  2. Istra district heating system. Master plan and feasibility study

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-09-01

    This report presents the results of the Feasibility Study of options for improving the efficiency and operating economy of Istra Large-Scale Demonstration Project includes all areas of the town of Istra. However, the Feasibility Study is confined to the five largest adjoining boilers plant areas within the borders of Istra town. The study was conducted from 1999 to 2001 and was based on information collected during this period. The city administration and the district heating company in Istra provided the data. The company RDIEE, Russian Danish Institute for Energy Efficiency, in Istra collected and processed the data under the conduction of Carl Bro a/s in Denmark. The main objectives of the study are to provide the Istra DHC with a number of options for future development of the district heating system based on technical/financial analyses and presenting the best possibilities for improved comfort, operation and business development. More concretely, one or more system improvement scenarios, which can be implemented in the near future as a first step of the recommended medium-term to long-term development, are identified. Another important objective has been to train the specialists of RDIEE in the feasibility study process and to transfer know-how, skills and tools. The model used for this study is adapted to the features and the special problems to be addressed in relation to the Istra district heating system. RDIEE and Istra DHC are thereby provided with a useful tool which may be used for continued study and development after the first phase project has been completed. As usual in the case of input/output models the quality of the results depends very much on the quality of input data. The present report is exclusively based on the consultant's understanding of the provided information. The results and the underlying inputs should be carefully considered before any final decision concerning implementation is taken. Verification of assumptions should also

  3. Field Implementation Plan for the In-Situ Bioremediation Treatability Study at the Technical Area-V Groundwater Area of Concern

    Energy Technology Data Exchange (ETDEWEB)

    Li, Jun [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2016-10-31

    This Field Implementation Plan (FIP) was prepared by Sandia National Laboratories, New Mexico (SNL/NM) and provides instruction on conducting a series of in-situ bioremediation (ISB) tests as described in the Revised Treatability Study Work Plan for In-Situ Bioremediation at the Technical Area-V Groundwater Area of Concern, referred to as the Revised Work Plan in this FIP. The Treatability Study is designed to gravity inject an electron-donor substrate and bioaugmentation bacteria into groundwater via three injection wells to perform bioremediation of the constituents of concern (COCs), nitrate and trichloroethene (TCE), in the regions with the highest concentrations at the Technical Area-V Groundwater (TAVG) Area of Concern (AOC). The Treatability Study will evaluate the effectiveness of bioremediation solution delivery and COC treatment over time. This FIP is designed for SNL/NM work planning and management. It is not intended to be submitted for regulator’s approval. The technical details presented in this FIP are subject to change based on field conditions, availability of equipment and materials, feasibility, and inputs from Sandia personnel and Aboveground Injection System contractor.

  4. Field Implementation Plan for the In-Situ Bioremediation Treatability Study at the Technical Area-V Groundwater Area of Concern

    International Nuclear Information System (INIS)

    Li, Jun

    2016-01-01

    This Field Implementation Plan (FIP) was prepared by Sandia National Laboratories, New Mexico (SNL/NM) and provides instruction on conducting a series of in-situ bioremediation (ISB) tests as described in the Revised Treatability Study Work Plan for In-Situ Bioremediation at the Technical Area-V Groundwater Area of Concern, referred to as the Revised Work Plan in this FIP. The Treatability Study is designed to gravity inject an electron-donor substrate and bioaugmentation bacteria into groundwater via three injection wells to perform bioremediation of the constituents of concern (COCs), nitrate and trichloroethene (TCE), in the regions with the highest concentrations at the Technical Area-V Groundwater (TAVG) Area of Concern (AOC). The Treatability Study will evaluate the effectiveness of bioremediation solution delivery and COC treatment over time. This FIP is designed for SNL/NM work planning and management. It is not intended to be submitted for regulator's approval. The technical details presented in this FIP are subject to change based on field conditions, availability of equipment and materials, feasibility, and inputs from Sandia personnel and Aboveground Injection System contractor.

  5. Feasibility and applications of RFID technologies to support Right-of-Way functions : technical report

    Science.gov (United States)

    2010-08-01

    Radio frequency identification device (RFID) technology provides the capability to store a unique identification : number and some basic attribute information, which can be retrieved wirelessly. This research project studied : the feasibility of usin...

  6. Proceedings of the remedial investigation/feasibility study workshop

    International Nuclear Information System (INIS)

    1988-12-01

    The objective of this workshop was to familiarize Department of Energy (DOE) personnel and contractors with all aspects of developing, managing, and conducting an RI/FS, based on HAZWRAP SCO experience in similar activities as part of the Installation Restoration program (IRP). The HAZWRAP SCO participation in Department of Defense (DOD) restoration activities provides an opportunity to develop capability and experience which are transferable to DOE activities. Paul Franco, Program Manager for the IRP, provided an overview of the IRP experience in conducting an RI/FS for a National Priorities List (NPL) site and a non-NPL site. A non-NPL site does not require an RI/FS by regulation; however, the RI/FS process can be used to determine whether to proceed with a feasibility study or terminate the action with a decision document. Al Porell, Program Manager for ICP, discussed the use of decision documents to remove non-NPL sites from regulatory consideration. DOE-Idaho has used similar documentation to remove numerous sites from their list of potential remedial action sites. Mr. Porell also discussed the use of the Technical Review Committee (TRC), which is established to coordinate activities during the RI/FS process. The TRC includes state, local, and federal authorities, and Air Force installation personnel

  7. Tactical and operational response to major incidents: feasibility and reliability of skills assessment using novel virtual environments.

    Science.gov (United States)

    Cohen, Daniel; Sevdalis, Nick; Patel, Vishal; Taylor, Michael; Lee, Henry; Vokes, Mick; Heys, Mick; Taylor, David; Batrick, Nicola; Darzi, Ara

    2013-07-01

    To determine feasibility and reliability of skills assessment in a multi-agency, triple-site major incident response exercise carried out in a virtual world environment. Skills assessment was carried out across three scenarios. The pre-hospital scenario required paramedics to triage and treat casualties at the site of an explosion. Technical skills assessment forms were developed using training syllabus competencies and national guidelines identified by pre-hospital response experts. Non-technical skills were assessed using a seven-point scale previously developed for use by pre-hospital paramedics. The two in-hospital scenarios, focusing on a trauma team leader and a silver/clinical major incident co-ordinator, utilised the validated Trauma-NOTECHS scale to assess five domains of performance. Technical competencies were assessed using an ATLS-style competency scale for the trauma scenario. For the silver scenario, the assessment document was developed using competencies described from a similar role description in a real-life hospital major incident plan. The technical and non-technical performance of all participants was assessed live by two experts in each of the three scenarios and inter-assessor reliability was computed. Participants also self-assessed their performance using identical proformas immediately after the scenarios were completed. Self and expert assessments were correlated (assessment cross-validation). Twenty-three participants underwent all scenarios and assessments. Performance assessments were feasible for both experts as well as the participants. Non-technical performance was generally scored higher than technical performance. Very good inter-rater reliability was obtained between expert raters across all scenarios and both technical and non-technical aspects of performance (reliability range 0.59-0.90, Psassessment in technical skills across all three scenarios (correlation range 0.52-0.84, Psskills. This study establishes feasibility and

  8. Transgastric endoscopic gastroenterostomy using a partially covered occluder: a canine feasibility study.

    Science.gov (United States)

    Luo, H; Pan, Y; Min, L; Zhao, L; Li, J; Leung, J; Xue, L; Yin, Z; Liu, X; Liu, Z; Sun, A; Li, C; Wu, K; Guo, X; Fan, D

    2012-05-01

    The use of natural orifice transluminal endoscopic surgery (NOTES) for gastroenterostomy has been previously reported, but it remains technically challenging and additional assistance is often needed. The aim of this study was to develop and evaluate a novel method for the creation of a gastroenterostomy using NOTES with an occluder. Transgastric endoscopic gastroenterostomy was performed in 12 healthy female dogs using a therapeutic upper gastrointestinal endoscope and a partially covered occluder. The occluder was removed with a snare 1 week later. The patency of the gastroenterostomy was confirmed by endoscopy, contrast radiological study, necropsy, and histological examination after 2 weeks. NOTES gastroenterostomy with an occluder was successful in all 12 dogs. The mean operative time was 32.3 ± 10.3 min (range 20.3 - 53.5). One dog (the first; 8.3 %) died 4 days after the operation of severe intra-abdominal infection due to incorrect deployment of the occluder and poor bowel preparation. Minor bleeding occurred at the anastomosis after removal of the occluder in two of the remaining dogs (18.2 %). Necropsy revealed postoperative adhesions that had developed at the anastomotic site in one dog (9.1 %). No anastomotic leakage or intestinal obstruction was observed. Complete healing of the anastomosis was confirmed on histological evaluation. Gastroenterostomy performed entirely by NOTES using an occluder was technically feasible in this survival animal model. © Georg Thieme Verlag KG Stuttgart · New York.

  9. Feasibility study of a nonequilibrium MHD accelerator concept for hypersonic propulsion ground testing

    International Nuclear Information System (INIS)

    Lee, Ying-Ming; Simmons, G.A.; Nelson, G.L.

    1995-01-01

    A National Aeronautics and Space Administration (NASA) funded research study to evaluate the feasibility of using magnetohydrodynamic (MHD) body force accelerators to produce true air simulation for hypersonic propulsion ground testing is discussed in this paper. Testing over the airbreathing portion of a transatmospheric vehicle (TAV) hypersonic flight regime will require high quality air simulation for actual flight conditions behind a bow shock wave (forebody, pre-inlet region) for flight velocities up to Mach 16 and perhaps beyond. Material limits and chemical dissociation at high temperature limit the simulated flight Mach numbers in conventional facilities to less than Mach 12 for continuous and semi-continuous testing and less than Mach 7 for applications requiring true air chemistry. By adding kinetic energy directly to the flow, MHD accelerators avoid the high temperatures and pressures required in the reservoir region of conventional expansion facilities, allowing MHD to produce true flight conditions in flight regimes impossible with conventional facilities. The present study is intended to resolve some of the critical technical issues related to the operation of MHD at high pressure. Funding has been provided only for the first phase of a three to four year feasibility study that would culminate in the demonstration of MHD acceleration under conditions required to produce true flight conditions behind a bow shock wave to flight Mach numbers of 16 or greater. MHD critical issues and a program plan to resolve these are discussed

  10. Quantitative feasibility study of magnetocaloric energy conversion utilizing industrial waste heat

    International Nuclear Information System (INIS)

    Vuarnoz, D.; Kitanovski, A.; Gonin, C.; Borgeaud, Y.; Delessert, M.; Meinen, M.; Egolf, P.W.

    2012-01-01

    Highlights: ► We model magnetic energy conversion machine for the use of industrial waste heat. ► Efficiencies and masses of the system are evaluated by a numerical model. ► Excellent potential of profitability is expected with large low-exergy heat sources. -- Abstract: The main objective of this theoretical study was to investigate under which conditions a magnetic energy conversion device (MECD) – utilizing industrial waste heat – is economically feasible. Furthermore, it was evaluated if magnetic energy conversion (MCE) has the potential of being a serious concurrent to already existing conventional energy conversion technologies. Up-today the availability of magnetocaloric materials with a high Curie temperature and a high magnetocaloric effect is rather limited. Therefore, this study was mainly focused on applications with heat sources of low to medium temperature levels. Magnetic energy conversion machines, containing permanent magnets, are numerically investigated for operation conditions with different temperature levels, defined by industrial waste heat sources and environmental heat sinks, different magnetic field intensities and different frequencies of operation (number of thermodynamic cycles per unit of time). Theoretical modeling and numerical simulations were performed in order to determine thermodynamic efficiencies and the exergy efficiencies as function of different operation conditions. From extracted data of our numerical results, approximate values of the total mass and total volume of magnetic energy conversion machines could be determined. These important results are presented dependent on the produced electric power. An economic feasibility study supplements the scientific study. It shows an excellent potential of profitability for certain machines. The most important result of this article is that the magnetic energy conversion technology can be economically and technically competitive to or even beat conventional energy

  11. Fluoroscopic and CT enteroclysis in children: initial experience, technical feasibility, and utility

    International Nuclear Information System (INIS)

    Brown, Shanaree; Applegate, Kimberly E.; Sandrasegaran, Kumar; Jennings, S.G.; Garrett, Joshua; Maglinte, Dean T.; Skantharajah, Arunan

    2008-01-01

    Partial small-bowel obstruction can be difficult to diagnose on clinical examination. These obstructions might not be detected on routine abdominal/pelvic CT. To evaluate the feasibility, safety, and techniques of fluoroscopic enteroclysis (FE) and CT enteroclysis (CTE), and to review their indications and findings in children. We retrospectively reviewed all enteroclysis studies in children younger than 18 years performed between January 2002 and March 2007. We correlated the results with other abdominal imaging and surgical and pathological findings. The review revealed 112 FE and 74 CTE studies performed in 175 children (mean age 14 years, range 3-18 years). FE and CTE studies were performed most commonly for evaluation of known Crohn disease (FE 38%, CTE 29%) and abdominal pain (FE 26%, CTE 26%). One FE study was terminated because of patient anxiety, and one CTE study was terminated because of patient discomfort. No complications of FE or CTE were reported. The findings were normal in 54% of the FE studies and 46% of the CTE studies. The most common small bowel diagnoses were Crohn disease (FE 34%, CTE 28%) and partial small bowel obstruction (FE 3%, CTE 10%). Two FE studies (2%) and 14 CTE studies (19%) showed abnormalities outside the small bowel. In 54 patients with inflammatory bowel disease, 11 FE studies and 25 CTE studies showed additional bowel abnormalities. Overall, 14 and 21 patients had surgery as a result of the findings of FE and CTE, respectively. FE and CTE are safe, feasible, and accurate in depicting small-bowel pathology in children. These techniques can be particularly useful in children with Crohn disease involving the small bowel. (orig.)

  12. Conceptual Thermal Treatment Technologies Feasibility Study

    International Nuclear Information System (INIS)

    Suer, A.

    1996-01-01

    This report presents a conceptual Thermal Treatment Technologies Feasibility Study (FS) for the Savannah River Site (SRS) focusing exclusively on thermal treatment technologies for contaminated soil, sediment, or sludge remediation projects

  13. Verification of Drift Seal Systems at the Morsleben Repository, Germany - Proof of Technical Feasibility and Functionality

    International Nuclear Information System (INIS)

    Wollrath, Juergen; Mauke, R.; Siemann, M.

    2014-01-01

    The Morsleben repository (ERAM) for low- and intermediate-level mainly short-lived radioactive wastes is located in a former salt mine. The closure concept is based on extensive backfilling with salt concrete complemented by seals that should prevent the penetration of solution into the waste emplacement areas and the emission of radionuclides out of these areas. The drift seals located in rock salt are made up of one or more segments of salt concrete in lengths between 25 m and 30 m. The sealing structure consists of three components: the seal body made of salt concrete, the contact zone between the seal body and the surrounding rock salt and the rock salt excavation damaged zone (EDZ). To demonstrate the feasibility of constructing such a seal structure an in-situ experiment is performed and a test drift and an accompanying parallel drift have been excavated for the experiment. The trial construction also comprises geotechnical instrumentation for stress, strain, displacement, temperature and pore pressure measurements and a comprehensive site investigation programme has been carried out, notably with regard to the stress state and the convergence behaviour of the surrounding rock salt. In addition to in-situ measurements, test specimens from different areas of the construction have been drilled and tested (strength and permeability). The pressure chamber has also been filled with brine solution to ascertain the permeability of the whole sealing structure. Another in-situ experiment is planned for the seal to be built in the non-creeping anhydrite. Both in-situ experiments will aid to prove the technical feasibility and functionality of the drift seal systems

  14. Feasibility Study of Economics and Performance of Wind Turbine Generators at the Newport Indiana Chemical Depot Site

    Energy Technology Data Exchange (ETDEWEB)

    Roberts, Joseph Owen [National Renewable Energy Lab. (NREL), Golden, CO (United States); Mosey, Gail [National Renewable Energy Lab. (NREL), Golden, CO (United States)

    2013-11-01

    The U.S. Environmental Protection Agency (EPA), in accordance with the RE-Powering America's Land initiative, selected the Newport Indiana Chemical Depot site in Newport, Indiana, for a feasibility study of renewable energy production. The National Renewable Energy Laboratory (NREL) was contacted to provide technical assistance for this project. The purpose of this report is to assess the sitefor possible wind turbine electrical generator installation and estimate the cost, performance, and site impacts of different wind energy options. In addition, the report recommends financing options that could assist in the implementation of a wind system at the site.

  15. Technical and economic feasibility of development innovative technological solutions for expansion the adjustment range of high-power CCP

    Science.gov (United States)

    Arakelyan, E. K.; Andryushin, A. V.; Burtsev, S. Y.; Andryushin, K. A.

    2017-11-01

    The analysis of technical and parametric constraints on the adjustment range of highpower CCP and recommended technological solutions in the technical literature for their elimination. Established that in the conditions of toughening the requirements for economy, reliability and maneuverability on the part of the system operator with the participation of CCP in control the frequency and power in the power system, existing methods do not ensure the fulfillment of these requirements. The current situation in the energy sector — the lack of highly manoeuvrable power equipment leads to the need participate in control of power consumption diagrams for all types of power plants, including CCP, although initially they were intended primarily for basic loads. Large-scale research conducted at the department of Automated control systems of technological processes, showed the possibility of a significant expansion of the adjustment range of CCP when it operating in the condensing mode and in the heating mode. The report presents the main results of these research for example the CCP-450 and CCP-450T. Various technological solutions are considered: when CCP in the condensation mode — the use of bypass steam distribution schemes, the transfer of a part of the steam turbine into a low-steam mode; when CCP operation in the heating mode — bypass steam distribution and the transfer CCP to gas turbine unit — power heating plants mode with the transfer the steam turbine to the motor mode. Data on the evaluation of the technical and economic feasibility of the proposed innovative technological solutions are presented in comparison with the methods used to solve this problem, which are used in practice, such as passing through the failures of the electric load graphs by transferring the CCP to the mode of operation with incomplete equipment. When comparing, both the economics, and the maneuverability and reliability of the equipment are considered.

  16. Feasibility study of a portable smelter for scrap metals

    International Nuclear Information System (INIS)

    Cavendish, J.H.

    1976-06-01

    The use of a portable smelter to process uranium-contaminated scrap metals was studied. Objectives were to convert scrap metal located at many diverse sites into a form which would be suitable for unlicensed sale and reduce the problems associated with storing the scrap. The Foundry Design Company study indicated the portable smelter concept was feasible from an equipment and transportation standpoint. Capital costs for a 5-ton/hour (steel) nominal capacity unit were estimated to be $2,349,000. Technical evaluation indicates that all the common metals considered, i.e., iron, nickel, copper, and aluminum, are amenable to uranium decontamination by smelting except aluminum. An economic evaluation of the processing of the 30,000 tons of steel scrap to be generated by the Cascade Improvement Program by a portable smelter was made based upon information supplied by Foundry Design Company, plus the assumption that the product metal could be sold for $120.00 per ton. This evaluation indicated a net return of $2,424,000 to the government could be realized. The Health and Safety study indicated no major problems of this nature would be encountered in operating a portable smelter. The legal review indicated the proposed operation fell within the authority of existing regulations. Consideration of possible conflicts with regard to competition with the private sector was suggested

  17. Geothermal district heating system feasibility analysis, Thermopolis, Wyoming

    Energy Technology Data Exchange (ETDEWEB)

    Goering, S.W.; Garing, K.L.; Coury, G.; Mickley, M.C.

    1982-04-26

    The purpose of this study is to determine the technical and economic feasibility of constructing and operating a district heating system to serve the residential, commercial, and public sectors in Thermopolis. The project geothermal resource assessment, based on reviews of existing information and data, indicated that substantial hot water resources likely exist in the Rose Dome region 10 miles northeast of Thermopolis, and with quantities capable of supporting the proposed geothermal uses. Preliminary engineering designs were developed to serve the space heating and hot water heating demands for buildings in the Thermopolis-East Thermopolis town service area. The heating district design is based on indirect geothermal heat supply and includes production wells, transmission lines, heat exchanger units, and the closed loop distribution and collection system necessary to serve the individual customers. Three options are presented for disposal of the cooled waters-reinjection, river disposal, and agricultural reuse. The preliminary engineering effort indicates the proposed system is technically feasible. The design is sized to serve 1545 residences, 190 businesses, and 24 public buildings. The peak design meets a demand of 128.2 million Btu at production rates of 6400 gpm.

  18. Factors Affecting Women Enrolment In Technical Institutions In Tanzania A Case Study Of Arusha Technical College

    OpenAIRE

    Glory B. Kaaya; Dr. Esther Waiganjo

    2015-01-01

    Abstract The purpose of this study was to investigate the factors affecting women enrolment in Technical Institutions in Tanzania by focusing on the women. The study examined in detail the factors affecting women enrolment in Technical institutions and Arusha Technical College in particular as well as exploring sexual dynamics within Technical Institutions. Moreover a number of theoretical frameworks were concerned basing on the objectives a case study design was employed involving both qua...

  19. Feasibility study 6 MW Multiwind MWT 6000 Triple Rotor Offshore Wind Turbine

    International Nuclear Information System (INIS)

    De Vries, E.

    2000-08-01

    This report contains results of a feasibility study carried out between September 1999 and January 2000. Multi-rotor technology is rather complex compared to conventional wind turbines, largely due to the increased number of components and (sub)systems. There are on the other hand also indications that the application of MULTIWIND features like the turnable subframe has the potential for a substantial reduction in energy generating costs. The study commenced with a set of preconditions and parameters like masses, dimensions, design features, indicative safety and control systems, etc. The key question to be answered was: 'is it possible to design a large 5 - 6 MW multi-rotor offshore wind turbine which can compete with comparable wind turbines of the same capacity and a single rotor, on the basis of overall concept, market acceptance and Costs of Energy (COE)? The main objectives are (1) to improve understanding of primary dynamic system interactions; (2) to quantify 'white spots' in the MULTIWIND know-how base (solvable problems with state-of-the-art solutions and not (immediately) solvable problems, requiring a technological breakthrough); and (3) to determine critical design parameters for various systems and alternative solutions. Secondary objectives were to analyse various concepts on the basis of technical aspects and Costs Of Energy (COE). The expected results are (1) a viable prototype concept based on proven state-of-the-art design solutions; and (2) clear outlines of a workable and cost effective installation and O and M strategy for large MWT-system optimised offshore wind power plants. For the methodology an integrated concept design approach has been adopted. This is considered essential from a project management, system dynamics, and COE points of view. Starting point were conclusions and recommendations of the lv-Marcon report. The structural design commenced with the positioning of the main yawing system and the conceptual dimensioning of the main

  20. Feasibility study on large pool-type LMFBR

    International Nuclear Information System (INIS)

    1984-01-01

    A feasibility study has been conducted from 1981 FY to 1983 FY, in order to evaluate the feasibility of a large pool-type LMFBR under the Japanese seismic design condition and safety design condition, etc. This study was aimed to establish an original reactor structure concept which meets those design conditions especially required in Japan. In the first year, preceding design concepts had been reviewed and several concepts were originated to be suitable to Japan. For typical two of them being selected by preliminary analysis, test programs were planned. In the second year, more than twenty tests with basic models had been conducted under severe conditions, concurrently analytical approaches were promoted. In the last year, larger model tests were conducted and analytical methods have been verified concerning hydrodynamic effects on structure vibration, thermo-hydraulic behaviours in reactor plena and so on. Finally the reactor structure concepts for a large pool-type LMFBR have been acknowledged to be feasible in Japan. (author)

  1. Dual-gated cardiac PET-clinical feasibility study

    Energy Technology Data Exchange (ETDEWEB)

    Teraes, Mika; Kokki, Tommi; Noponen, Tommi; Hoppela, Erika; Sipilae, Hannu T.; Knuuti, Juhani [Turku PET Centre, PO BOX 52, Turku (Finland); Durand-Schaefer, Nicolas [General Electric Medical Systems, Buc (France); Pietilae, Mikko [Turku University Hospital, Department of Internal Medicine, Turku (Finland); Kiss, Jan [Turku University Hospital, Department of Surgery, Turku (Finland)

    2010-03-15

    Both respiratory and cardiac motions reduce image quality in myocardial imaging. For accurate imaging of small structures such as vulnerable coronary plaques, simultaneous cardiac and respiratory gating is warranted. This study tests the feasibility of a recently developed robust method for cardiac-respiratory gating. List-mode data with triggers from respiratory and cardiac cycles are rearranged into dual-gated segments and reconstructed with standard algorithms of a commercial PET/CT scanner. Cardiac gates were defined as three fixed phases and one variable diastolic phase. Chest motion was measured with a respiratory gating device and post-processed to determine gates. Preservation of quantification in dual-gated images was tested with an IEC whole-body phantom. Minipig and human studies were performed to evaluate the feasibility of the method. In minipig studies, a coronary catheter with radioactive tip was guided in coronary artery for in vivo and ex vivo acquisitions. Dual gating in humans with suspected cardiac disorders was performed using 18-F-FDG as a tracer. The method was found feasible for in vivo imaging and the radioactive catheter tip was better resolved in gated images. In human studies, the dual gating was found feasible and easy for clinical routine. Maximal movement of myocardial surface in cranio-caudal direction was over 20 mm. The shape of myocardium was clearly different between the gates and papillary muscles become more visible in diastolic images. The first clinical experiences using robust cardiac-respiratory dual gating are encouraging. Further testing in larger clinical populations using tracers designed especially for plaque imaging is warranted. (orig.)

  2. Dual-gated cardiac PET-clinical feasibility study

    International Nuclear Information System (INIS)

    Teraes, Mika; Kokki, Tommi; Noponen, Tommi; Hoppela, Erika; Sipilae, Hannu T.; Knuuti, Juhani; Durand-Schaefer, Nicolas; Pietilae, Mikko; Kiss, Jan

    2010-01-01

    Both respiratory and cardiac motions reduce image quality in myocardial imaging. For accurate imaging of small structures such as vulnerable coronary plaques, simultaneous cardiac and respiratory gating is warranted. This study tests the feasibility of a recently developed robust method for cardiac-respiratory gating. List-mode data with triggers from respiratory and cardiac cycles are rearranged into dual-gated segments and reconstructed with standard algorithms of a commercial PET/CT scanner. Cardiac gates were defined as three fixed phases and one variable diastolic phase. Chest motion was measured with a respiratory gating device and post-processed to determine gates. Preservation of quantification in dual-gated images was tested with an IEC whole-body phantom. Minipig and human studies were performed to evaluate the feasibility of the method. In minipig studies, a coronary catheter with radioactive tip was guided in coronary artery for in vivo and ex vivo acquisitions. Dual gating in humans with suspected cardiac disorders was performed using 18-F-FDG as a tracer. The method was found feasible for in vivo imaging and the radioactive catheter tip was better resolved in gated images. In human studies, the dual gating was found feasible and easy for clinical routine. Maximal movement of myocardial surface in cranio-caudal direction was over 20 mm. The shape of myocardium was clearly different between the gates and papillary muscles become more visible in diastolic images. The first clinical experiences using robust cardiac-respiratory dual gating are encouraging. Further testing in larger clinical populations using tracers designed especially for plaque imaging is warranted. (orig.)

  3. Using Remote Communication Technology in Insulin Pump Training: A Feasibility Study.

    Science.gov (United States)

    Parks, Linda; Kim, Tae Youn

    2015-09-29

    This feasibility study was designed to examine if remote communication technology can be used in the technical training of an insulin pump in adults with diabetes who were familiar with insulin pump therapy. Surveys were emailed to 69 individuals who purchased an insulin pump and had been trained by the manufacturer's diabetes educators. In consultation with providers, participants were given the choice of receiving training in a face-to-face meeting or via remote communication technology. The survey consisted of 27 questions asking participants' characteristics, device proficiency, confidence, and their satisfaction with the insulin pump and the training method. Differences between the 2 groups were examined using bivariate analyses. There were 17 participants in the remote group and 20 participants in the face-to-face group. Participants had a mean age of 40.9 ± 14.3 years, had diabetes for 24.3 ± 13.8 years, and used an insulin pump for 9.8 ± 4.9 years. The participants in both groups were not statistically different in age, diabetes history, years on insulin pump, device proficiency, confidence, or satisfaction with the training method. The remote group reported less graduate-level education (P remote communication technology may be an effective tool to provide technical training to adults who are familiar with insulin pump therapy. Additional research is required to determine the effectiveness of the remote insulin pump training. © 2015 Diabetes Technology Society.

  4. Feasibility Study: New Knowledge Demands in Turbulent Business World

    Science.gov (United States)

    Sprice, Renate; Kirikova, Marite

    Feasibility study is one of the early activities in information systems (IS) development when important decisions regarding choice among several possible systems development alternatives are to be made. In times of relatively stable business environment and waterfall model as a systems development approach, the role and methods of feasibility study where quite clear (Kendall and Kendall 1995). However, new software development methods and the necessity to develop more rapidly new IS or their parts may. challenge the possibility to evaluate project feasibility in the early stages of IS development.

  5. Recent progress in the feasibility study for the first nuclear power plant in Indonesia

    International Nuclear Information System (INIS)

    Subki, I.R.; Iskandar, A.; Supadi, S.

    1994-01-01

    In September 1989 the Indonesian Government decided to perform a Nuclear Power Plant feasibility study, including a comprehensive investigation of Muris site. This presentation reports on the progress to date in the two main components of this study: (a) the non-site studies, covering energy economics, financing, technical and safety aspects, the fuel cycle and waste management as well as general management aspects, and (b) site and environmental studies, covering field investigations, assessment of site selection, site qualification/evaluation, environmental, socio-economic and cultural impacts. The study is carried out under a comprehensive quality assurance programme developed by a consultancy company - NEWJEC Inc., which compiles with IAEA recommendations and was approved by BATAN. A summary of the main results, recommendations and general conclusions is presented. It is estimated that the total investment for the construction of 2 x 900 MWe or 3 x 600 MWe class Nuclear Power Plant units would be around US$7 to US$9 billion. 8 tabs

  6. MRS feasibility assessment grant technical progress report

    International Nuclear Information System (INIS)

    1993-01-01

    On January 13, 1993, Governor of the State of Utah, Mike Leavitt officially announced that he was opposing a MRS Facility in the State of Utah and informed San Juan County of his decision which will preclude the County from applying for a Phase IIa feasibility grant. A copy of the policy statement made by Governor Leavitt is included in this report. Additionally, a bill in the State House of Representative has been filed opposing the facility. A copy of the bill is also included. The work accomplished under Phase I, indicated that there was about an equal amount of residents in San Juan County opposed and in favor of the facility. There were many concerns and issues presented during the Phase I grant period that would have been continued to Phase IIa, if allowed, including the citizen committee

  7. Thermoablation of Malignant Kidney Tumors Using Magnetic Nanoparticles: An In Vivo Feasibility Study in a Rabbit Model

    International Nuclear Information System (INIS)

    Bruners, Philipp; Braunschweig, Till; Hodenius, Michael; Pietsch, Hubertus; Penzkofer, Tobias; Baumann, Martin; Guenther, Rolf W.; Schmitz-Rode, Thomas; Mahnken, Andreas H.

    2010-01-01

    The objective of this study was to assess the technical feasibility of CT-guided magnetic thermoablation for the treatment of malignant kidney tumors in a VX2 tumor rabbit model. VX2 tumors were implanted into the kidneys of five rabbits and allowed to grow for 2 weeks. After preinterventional CT perfusion imaging, CT-guided injection of superparamagnetic iron oxide particles (300 μl) was performed, followed by exposure of the animals to an alternating electromagnetic field for 15 min (∼0.32 kA/m). Then animals underwent CT perfusion imaging again. Afterward, animals were sacrificed and kidneys were dissected for macroscopic and histological evaluation. Changes in perfusion before and after exposure to the alternating magnetic field were analyzed. In one animal no tumor growth could be detected so the animal was used for optimization of the ablation procedure including injection technique and peri-interventional cross-sectional imaging (CT, MRI). After image-guided intratumoral injection of ferrofluids, the depiction of nanoparticle distribution by CT correlated well with macroscopic evaluation of the dissected kidneys. MRI was limited due to severe susceptibility artefacts. Postinterventional CT perfusion imaging revealed a perfusion deficiency around the ferrofluid deposits. Histological workup showed different zones of thermal damage adjacent to the ferrofluid deposits. In conclusion, CT-guided magnetic thermoablation of malignant kidney tumors is technically feasible in an animal model and results in a perfusion deficiency indicating tumor necrosis as depicted by CT perfusion imaging and shown in histological evaluation.

  8. A Feasibility Study of Steelmaking by Molten Oxide Electrolysis (TRP9956)

    Energy Technology Data Exchange (ETDEWEB)

    Donald R. Sadoway; Gerbrand Ceder

    2009-12-31

    Molten oxide electrolysis (MOE) is an extreme form of molten salt electrolysis, a technology that has been used to produce tonnage metals for over 100 years - aluminum, magnesium, lithium, sodium and the rare earth metals specifically. The use of carbon-free anodes is the distinguishing factor in MOE compared to other molten salt electrolysis techniques. MOE is totally carbon-free and produces no CO or CO2 - only O2 gas at the anode. This project is directed at assessing the technical feasibility of MOE at the bench scale while determining optimum values of MOE operating parameters. An inert anode will be identified and its ability to sustain oxygen evalution will be demonstrated.

  9. COLD-SAT feasibility study safety analysis

    Science.gov (United States)

    Mchenry, Steven T.; Yost, James M.

    1991-01-01

    The Cryogenic On-orbit Liquid Depot-Storage, Acquisition, and Transfer (COLD-SAT) satellite presents some unique safety issues. The feasibility study conducted at NASA-Lewis desired a systems safety program that would be involved from the initial design in order to eliminate and/or control the inherent hazards. Because of this, a hazards analysis method was needed that: (1) identified issues that needed to be addressed for a feasibility assessment; and (2) identified all potential hazards that would need to be controlled and/or eliminated during the detailed design phases. The developed analysis method is presented as well as the results generated for the COLD-SAT system.

  10. Logistic management materials-technical support railway enterprises

    OpenAIRE

    Dykan, V.; Borozenetc, T.

    2014-01-01

    The essence of logistics management. Determine the feasibility of applying the principles of logistics management in organizing the logistics of railway transport. Discussed measures to develop suppliers in the implementation of logistics management logistics. Identified the need to develop and implement regulatory and methodical system to improve materials-technical support through the introduction of modern logistics principles. Applied systemic campaign to organize the materials-technical ...

  11. The environmental energy sector programme. Poland: Feasibility study

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-07-01

    The Danish Ministry of Energy has granted financial aid to the preparation of a feasibility study necessary for the procurement of a financial solution to the modernisation of the combined heat and power plant in the city of Zielona Gora.The overall objectives of the Feasibility Study are to: establish new efficient power capacity in the south-west region of Poland, increase the energy efficiency, reduce the impact on the environment, utilise the local natural gas available which cannot be used in the national gas grid and reduce the costs of energy supply.The specific objective of this feasibility study is to obtain the best possible financing of the erection of a new CPH plant in Zielona Gora. The plant shall be designed to utilise the local resources of natural gas and to supply heat to the district heating grid in accordance with long-term planning strategies. (EHS)

  12. The deep geothermal project in Lavey, Switzerland - Phase B: Technical and financial feasibility study - Synthesis report; Projet de geothermie profonde a Lavey (VD). Phase B : Etude de faisabilite technicofinanciere - Rapport de synthese

    Energy Technology Data Exchange (ETDEWEB)

    Bianchetti, G.; Crestin, G. [Alpgeo Sarl, Sierre (Switzerland); Dewarrat, P.; Perritaz, D. [Energie Concept SA, Bulle, (Switzerland)] [and others

    2009-06-15

    An overview of the deep geothermal project in Lavey, Switzerland is presented. The site is located near the Rhone river, where this river crosses a mountain chain in the Alps. The geology of the region is described. A well known spa is located in Lavey. The aim of the project is to generate power and deliver heat to a local district heating. Two wells should be bored to capture underground water at an appropriate temperature. The present report summarises the previous studies and focuses on the technical and financial feasibility of the future cogeneration plant. In particular, it presents the foreseen installations and the potential heat users. The costs are estimated in several possible boring scenarios. The most promising strategy is similar to that adopted decades ago in the Austrian spa of Bad Blumau. It combines geothermal energy and biomass. A business plan is presented. Recommendations for the next steps are given.

  13. A feasibility study of boron-loaded liquid scintillator for the detection of electron anti-neutrinos

    CERN Document Server

    Wang, S C; Leung, R W S; Wang, S L; Chang, C Y; Chen Chi Ping; Cheng, K C; Ho, T I; Lai, W P; Liu, H M; Mao, Z P; Shih, I C; Wong, H T; Yu, Z Q

    1999-01-01

    Boron-loaded liquid scintillator offers some potential advantages as a detector for electron anti-neutrinos. A research program was carried out with the objective of developing such scintillators. The crucial feature is the pulse shape discrimination properties following the neutron capture by sup 1 sup 0 B. Results of the R and D efforts are presented. The feasibility and the technical difficulties of carrying out a full-scale neutrino experiment based on this approach are discussed. (author)

  14. Feasibility Study of Cargo Airship Transportation Systems Powered by New Green Energy Technologies

    Science.gov (United States)

    Skuza, Jonathan R.; Park, Yeonjoon; Kim, Hyun Jung; Seaman, Shane T.; King, Glen C.; Choi, Sang H.; Song, Kyo D.; Yoon, Hargsoon; Lee, Kunik

    2014-01-01

    The development of transportation systems that use new and sustainable energy technologies is of utmost importance due to the possible future shortfalls that current transportation modes will encounter because of increased volume and costs. The introduction and further research and development of new transportation and energy systems by materials researchers at the National Aeronautics and Space Administration (NASA) Langley Research Center (LaRC) and the Department of Transportation are discussed in this Technical Memorandum. In this preliminary study, airship concepts were assessed for cargo transportation using various green energy technologies capable of 24-hour operation (i.e., night and day). Two prototype airships were successfully constructed and tested at LaRC to demonstrate their feasibility: one with commercially available solar cells for operation during the daytime and one with microwave rectennas (i.e., rectifying antennas) developed in-house for night-time operation. The test results indicate the feasibility of a cargo transportation airship powered by new green energy sources and wireless power technology. Future applications will exploit new green energy sources that use materials and devices recently developed or are in the process of being developed at LaRC. These include quantum well SiGe solar cells; low, mid-, and high temperature thermoelectric modules; and wireless microwave and optical rectenna devices. This study examines the need and development of new energy sources for transportation, including the current status of research, materials, and potential applications.

  15. Study of technical and financial pre-feasibility for the handling and sale, as fuel in cement industries, of petroleum coke produced at a petroleum refinery located in Moin, Limon

    International Nuclear Information System (INIS)

    Corrales Suarez, Jeffry

    2013-01-01

    A study of the technical and financial pre-feasibility is realized for the handling, conditioning and sale as fuel in cement industries of petroleum coke, that is produced in the project of extension and modernization of the refinery of RECOPE in Moin, Limon. Daily production has been of 570 metric tons. The market study has determined a demand of approximately 120 000 metric tons in the country and in the region. The total production of coke has been possible place it at national and regional level, due to lack of another producer. The coke is recommended to crush it to decrease the size of the particles for the conditioning, handling and to facilitate their manipulation. Conveyor belts are used for handling on the inside of the refinery. The coke is transported in trucks type tanker on the exterior of the refinery. The moisture content is reduced by dryer vibratory of fluidized bed to 5% of moisture to guarantee a product better quality. The product is stored under roof in ventilated facilities and with appropriate systems of security to minimize the risk of an accident. The fixed capital investment to develop the project has been of USD 3,1 millions and working capital of USD 14,4 millions. The financial evaluation is realized considering two financing models of 70% and without financing. The net present value (NPV) has been of USD -13,0 millions and the desirability index of -6,6 for the model with financing. The model without financing has obtained a NPV of USD -1,9 millions and a desirability index of -1,2. The financial profitability of the project has been very sensitive to the sales price of the coke, to the coke volume of production, to the growth percentage of the sale price and the cost of the raw material for the two models considered. The financial risk analysis is realized by the Monte Carlo method, whereupon is obtained a probability of approximately 34% in that the internal rate of return (IRR) has been higher than the cut rate and of 36% in that

  16. Point-of-care diagnosis of periodontitis using saliva: technically feasible but still a challenge

    Directory of Open Access Journals (Sweden)

    Suk eJi

    2015-09-01

    Full Text Available Periodontitis is a chronic inflammation of the periodontium caused by persistent bacterial infection that leads to the breakdown of connective tissue and bone. Because the ability to reconstruct the periodontium is limited after alveolar bone loss, early diagnosis and intervention should be the primary goals of periodontal treatment. However, periodontitis often progresses without noticeable symptoms, and many patients do not seek professional dental care until the periodontal destruction progresses to the point of no return. Furthermore, the current diagnosis of periodontitis depends on time-consuming clinical measurements. Therefore, there is an unmet need for near-patient testing to diagnose periodontitis. Saliva is an optimal biological fluid to serve as a near-patient diagnostic tool for periodontitis. Recent developments in point-of-care (POC testing indicate that a diagnostic test for periodontitis using saliva is now technically feasible. A number of promising salivary biomarkers associated with periodontitis have been reported. A panel of optimal biomarkers must be carefully selected based on the pathogenesis of periodontitis. The biggest hurdle for the POC diagnosis of periodontitis using saliva may be the process of validation in a large, diverse patient population. Therefore, we propose the organization of an International Consortium for Biomarkers of Periodontitis, which will gather efforts to identify, select, and validate salivary biomarkers for the diagnosis of periodontitis.

  17. Feasibility study of a soil-based rubberized CLSM.

    Science.gov (United States)

    Wu, Jason Y; Tsai, Mufan

    2009-02-01

    The development of beneficial uses of recycled scrap tires is always in great demand around the world. The disposal of on-site surplus excavated soil and the production of standard engineering aggregates have also been facing increasing environmental and ecological challenges in congested islands, such as Taiwan. This paper presents an experimental study using recycled crumb rubber and native silty sand to produce a lightweight, soil-based, rubberized controlled low strength material (CLSM) for a bridge approach repair. To assess the technical feasibility of this material, the effects of weight ratios of cement-to-water (C/W) and water-to-solid (W/S), and of rubber content on the engineering properties for different mixtures were investigated. The presented test results include flowability, unit weight, strength, settlement potential, and bearing capacity. Based on the findings, we conclude that a soil-based rubberized CLSM with 40% sand by weight and an optimal design ratio of 0.7 for C/W and 0.35 for W/S can be used for the proposed bridge approach repair. Such a mixture has demonstrated acceptable flowability, strength, and bearing capacity. Its lower unit weight, negligible compressibility, and hydrocollapse potential also help ensure that detrimental settlement is unlikely to occur. The results illustrate a novel scheme of CLSM production, and suggest a beneficial alternative for the reduction of scrap tires as well as conservation of resources and environment.

  18. TECHNICAL ECONOMIC FEASIBILITY OF PADDY RICE FIELDS VARIETY OF APPROACH PTT SPECIFIC LOCATIONS IN PAPUA (Case Jayapura

    Directory of Open Access Journals (Sweden)

    Afrizal Malik

    2013-01-01

    Full Text Available Study aims to determine technical economically feasibility of irrigration rice in village of Sumbe, Namblong District, Jayapura on-farm research involving farmers with an area of 2.50 ha cooperators, July to November 2011. Technology introduced: PTT, 4:1 legowo systems, seed varieties Inpari labeled 1, 2, 4, 6, 7, 9, 10, and Sintanur. Fertilizer: urea 150 kg +100 kg +100 kg SP-36 Phonska KCl +50 kg per ha. Variables: height and number of tillers 35 and 65 dap, weight of 1000 seeds, productivity, input, and output. Data were analyzed descriptively. Highest productivity in varieties Inpari 7 (7.925 tonnes per ha Milled Rice (MR and lowest Sintanur varieties (4.625 tonnes per ha MR. Pest stand: rice leaffolder and stinky rice pest. Lowest expenditure on non-cooperators Ciherang farmers IDR 12.15 million per ha per Growing Season (GS and highest in varieties Inpari 7 (IDR 15,005,000 per ha per GS. Lowest Acceptance Ciherang farmers on non-cooperators, IDR 16.4 million per ha per GS and highest in varieties Inpari 7, IDR 27.7 million per ha per GS. If farmers apply recommendation technologies using Inpari 7 varieties, farmers receiving IDR 3,173,750 per month (greater than Regional Minimum Wage of Jayapura. Need government support in order to minimize dependence on outside

  19. Radiation processing of flue gases: Guidelines for feasibility studies

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-12-01

    The aim of this publication is to facilitate the performance of feasibility studies for Electron Beam flue gas cleanup projects by providing guidelines to conduct these studies and compiling information on the state of the art. This document summarizes the contents of a feasibility study; discusses the main items in plant construction, measurement and control systems, radiation safety and building construction; and lists the required economic data for internationally funded projects.

  20. Radiation processing of flue gases: Guidelines for feasibility studies

    International Nuclear Information System (INIS)

    2000-12-01

    The aim of this publication is to facilitate the performance of feasibility studies for Electron Beam flue gas cleanup projects by providing guidelines to conduct these studies and compiling information on the state of the art. This document summarizes the contents of a feasibility study; discusses the main items in plant construction, measurement and control systems, radiation safety and building construction; and lists the required economic data for internationally funded projects

  1. Feasibility of disposal of high-level radioactive waste into the seabed. Volume 3: Geoscience characterization studies

    International Nuclear Information System (INIS)

    Shephard, L.E.; Auffret, G.A.; Buckley, D.E.; Schuettenhelm, R.T.E.; Searle, R.C.

    1988-01-01

    One of the options suggested for disposal of high-level radioactive waste resulting from the generation of nuclear power is burial beneath the deep ocean floor in geologically stable sediment formations which have no economic value. The 8-volume series provides an assessment of the technical feasibility and radiological safety of this disposal concept based on the results obtained by ten years of co-operation and information exchange among the Member countries participating in the NEA Seabed Working Group. This report summarizes the results of a study performed to establish if, on the basis of available data, sites may be found that will satisfy the geoscience requirements for a potential subseabed high-level waste repository

  2. Feasibility study for a biomedical experimental facility based on LEIR at CERN

    CERN Document Server

    Abler, Daniel; Carli, Christian; Dosanjh, Manjit; Peach, Ken; Orecchia, Roberto

    2013-01-01

    In light of the recent European developments in ion beam therapy, there is a strong interest from the biomedical research community to have more access to clinically relevant beams. Beamtime for pre-clinical studies is currently very limited and a new dedicated facility would allow extensive research into the radiobiological mechanisms of ion beam radiation and the development of more refined techniques of dosimetry and imaging. This basic research would support the current clinical efforts of the new treatment centres in Europe (for example HIT, CNAO and MedAustron). This paper presents first investigations on the feasibility of an experimental biomedical facility based on the CERN Low Energy Ion Ring LEIR accelerator. Such a new facility could provide beams of light ions (from protons to neon ions) in a collaborative and cost-effective way, since it would rely partly on CERN’s competences and infrastructure. The main technical challenges linked to the implementation of a slow extraction scheme for LEIR an...

  3. Feasibility and safety of augmented reality-assisted urological surgery using smartglass.

    Science.gov (United States)

    Borgmann, H; Rodríguez Socarrás, M; Salem, J; Tsaur, I; Gomez Rivas, J; Barret, E; Tortolero, L

    2017-06-01

    To assess the feasibility, safety and usefulness of augmented reality-assisted urological surgery using smartglass (SG). Seven urological surgeons (3 board urologists and 4 urology residents) performed augmented reality-assisted urological surgery using SG for 10 different types of operations and a total of 31 urological operations. Feasibility was assessed using technical metadata (number of photographs taken/number of videos recorded/video time recorded) and structured interviews with the urologists on their use of SG. Safety was evaluated by recording complications and grading according to the Clavien-Dindo classification. Usefulness of SG for urological surgery was queried in structured interviews and in a survey. The implementation of SG use during urological surgery was feasible with no intrinsic (technical defect) or extrinsic (inability to control the SG function) obstacles being observed. SG use was safe as no grade 3-5 complications occurred for the series of 31 urological surgeries of different complexities. Technical applications of SG included taking photographs/recording videos for teaching and documentation, hands-free teleconsultation, reviewing patients' medical records and images and searching the internet for health information. Overall usefulness of SG for urological surgery was rated as very high by 43 % and high by 29 % of surgeons. Augmented reality-assisted urological surgery using SG is both feasible and safe and also provides several useful functions for urological surgeons. Further developments and investigations are required in the near future to harvest the great potential of this exciting technology for urological surgery.

  4. Feasibility study and technical proposal for seismic monitoring of tunnel boring machine in Olkiluoto

    Energy Technology Data Exchange (ETDEWEB)

    Saari, J.; Lakio, A. (AF-Consult Ltd, Vantaa (Finland))

    2009-01-15

    In Olkiluoto, Posiva Oy has operated a local seismic network since February 2002. The purpose of the microearthquake measurements at Olkiluoto is to improve understanding of the structure, behaviour and long term stability of the bedrock. The studies include both tectonic and excavation-induced microearthquakes. An additional task of monitoring is related to safeguarding of the ONKALO. The possibility to excavate an illegal access to the ONKALO, have been concerned when the safeguards are discussed. Therefore all recorded explosions in the Olkiluoto area and in the ONKALO are located. If a concentration of explosions is observed, the origin of that is found out. Also a concept of hidden illegal explosions, detonated at the same time as the real excavation blasts, has been examined. According to the experience gained in Olkiluoto, it can be concluded that, as long the seismic network is in operation and the results are analysed by a skilled person, it is practically impossible to do illegal excavation by blasts. In this report a possibility of seismic monitoring of illegal excavation done by tunnel boring machine (TBM) has been investigated. Characteristics of the seismic signal generated by the raise boring machine are described. According to this study, it can be concluded that the generated seismic signal can be detected and the source of the signal can be located. However, this task calls for different kind of monitoring system than that, which is currently used for monitoring microearthquakes and explosions. The presented technical proposal for seismic monitoring of TBM in Olkiluoto is capable to detect and locate TBM coming outside the ONKALO area about two months before it would reach the ONKALO. (orig.)

  5. Feasibility study and technical proposal for seismic monitoring of tunnel boring machine in Olkiluoto

    International Nuclear Information System (INIS)

    Saari, J.; Lakio, A.

    2009-01-01

    In Olkiluoto, Posiva Oy has operated a local seismic network since February 2002. The purpose of the microearthquake measurements at Olkiluoto is to improve understanding of the structure, behaviour and long term stability of the bedrock. The studies include both tectonic and excavation-induced microearthquakes. An additional task of monitoring is related to safeguarding of the ONKALO. The possibility to excavate an illegal access to the ONKALO, have been concerned when the safeguards are discussed. Therefore all recorded explosions in the Olkiluoto area and in the ONKALO are located. If a concentration of explosions is observed, the origin of that is found out. Also a concept of hidden illegal explosions, detonated at the same time as the real excavation blasts, has been examined. According to the experience gained in Olkiluoto, it can be concluded that, as long the seismic network is in operation and the results are analysed by a skilled person, it is practically impossible to do illegal excavation by blasts. In this report a possibility of seismic monitoring of illegal excavation done by tunnel boring machine (TBM) has been investigated. Characteristics of the seismic signal generated by the raise boring machine are described. According to this study, it can be concluded that the generated seismic signal can be detected and the source of the signal can be located. However, this task calls for different kind of monitoring system than that, which is currently used for monitoring microearthquakes and explosions. The presented technical proposal for seismic monitoring of TBM in Olkiluoto is capable to detect and locate TBM coming outside the ONKALO area about two months before it would reach the ONKALO. (orig.)

  6. Results of FY 2002 of feasibility study on commercialized fast reactor cycle systems. Phase 2

    International Nuclear Information System (INIS)

    2003-06-01

    Japan Nuclear Cycle Development Institute (JNC) and Japan Atomic Power Company (JAPC, that is the representative of the electric utilities in Japan) established a new organization to develop a commercialized fast reactor (FR) cycle system on July 1, 1999 and feasibility study (F/S) was undertaken in order to determine the promising concepts and to define the necessary R and D tasks. During Phase 1 (JFY 1999 and 2000), a number of candidate concepts were screened from various options, featuring innovative technologies. In the F/S, the options were evaluated and conceptual designs were examined considering the attainable perspectives for following: 1) ensuring safety, 2) economic competitiveness to future LWRs, 3) efficient utilization of resources, 4) reduction of environmental burden and 5) enhancement of nuclear non-proliferation. The F/S should also guide the necessary R and D to commercialize FR cycle system. To begin with the study of feasible candidate concepts screened in Phase I, Phase 2 started in the plan for five years in 2001. This aims at clarifying several feasible candidate concepts and deciding the research plan after Phase 3 as taking into consideration the innovative technology. As for this plan, an interim report will be carried out in 2003 as one pause and the prospect to clarify the feasible candidates will be expected. Furthermore, after the completion of this research and investigation program, research and development activities will be carried out under a rolling plan in which reviews will be carried out approximately every five years. The objective of these R and D activities is to make a proposal regarding highly attractive and competitive FR cycle system technology that assures safety by 2015. This report summarizes the results of F/S of Phase 2 in 2002. In 2002, the second year of Phase 2, the study was advanced along with the plan which was evaluated by the committee for the Evaluation. Then, in the study of FR system and fuel cycle

  7. Technical and operational feasibility of psychrophilic anaerobic digestion biotechnology for processing ammonia-rich waste

    International Nuclear Information System (INIS)

    Massé, Daniel I.; Rajagopal, Rajinikanth; Singh, Gursharan

    2014-01-01

    Highlights: • Long-term anaerobic digestion (AD) process at high-ammonia (>5 gN/L) is limited. • PADSBR technology was validated to treat N-rich waste with 8.2 ± 0.3 gNH 3 -N/L. • Excess ammonia (8.2 gN/L) did not affect the digestion process with no inhibition. • VFA, an indicator for process stability, did not accumulate in PADSBR. • Biomass acclimation in PADSBR ensured a high-stabilization of the AD process. - Abstract: Ammonia nitrogen plays a critical role in the performance and stability of anaerobic digestion (AD) of ammonia rich wastes like animal manure. Nevertheless, inhibition due to high ammonia remains an acute limitation in AD process. A successful long-term operation of AD process at high ammonia (>5 gN/L) is limited. This study focused on validating technical feasibility of psychrophilic AD in sequencing batch reactor (PADSBR) to treat swine manure spiked with NH 4 Cl up to 8.2 ± 0.3 gN/L, as a representative of N-rich waste. CODt, CODs, VS removals of 86 ± 3, 82 ± 2 and 73 ± 3% were attained at an OLR of 3 gCOD/L.d, respectively. High-ammonia had no effect on methane yields (0.23 ± 0.04 L CH 4 /gTCOD fed ) and comparable to that of control reactors, which fed with raw swine manure alone (5.5 gN/L). Longer solids/hydraulic retention times in PADSBRs enhanced biomass acclimation even at high-ammonia. Thus VFA, an indicator for process stability, did not accumulate in PADSBR. Further investigation is essential to establish the maximum concentrations of TKN and free ammonia that the PADSBR can sustain

  8. Feasibility study on small modular reactors for modern microgrids

    Energy Technology Data Exchange (ETDEWEB)

    Islam, R.; Gabbar, H.A., E-mail: hossam.gabbar@uoit.ca [Univ. of Ontario Inst. of Technology, Faculty of Energy Systems and Nuclear Science, Oshawa, Ontario (Canada)

    2013-07-01

    Microgrid is a solution of conventional power grid problem and offer sustainable decentralized power system. Microgrid with modern distributed energy resources (DER) could play an important role to alleviate dependency on the main electricity grid. Distributed energy resource comprises wind turbine, solar photovoltaic, diesel generator, gas engine, micro turbine, fuel cells, etc.Due to the gap between typical loads and supply within microgrid, larger scale energy generation could provide a possible solution to balance power demand and supply. Feasibility study of Small Nuclear Power Plant, such as Small Modular reactor (SMR), within microgrids could be achieved via different cases. To achieve the target, a comprehensive feasibility study is conducted on microgrid with SMR through electricity generation profiles, geographical and environmental assessment, as well as cost analysis using simulation practices and data analysis.Also potency of SMRs is analyzed. Parameters and Key Performance Indicators (KPIs) could be analyzed to achieve feasible solution of microgrids with small modular reactor (SMR) to improve the overall microgrid performance.The study shows that SMR could be a feasible solution if microgrid parameters are selected properly. (author)

  9. Feasibility study on small modular reactors for modern microgrids

    International Nuclear Information System (INIS)

    Islam, R.; Gabbar, H.A.

    2013-01-01

    Microgrid is a solution of conventional power grid problem and offer sustainable decentralized power system. Microgrid with modern distributed energy resources (DER) could play an important role to alleviate dependency on the main electricity grid. Distributed energy resource comprises wind turbine, solar photovoltaic, diesel generator, gas engine, micro turbine, fuel cells, etc.Due to the gap between typical loads and supply within microgrid, larger scale energy generation could provide a possible solution to balance power demand and supply. Feasibility study of Small Nuclear Power Plant, such as Small Modular reactor (SMR), within microgrids could be achieved via different cases. To achieve the target, a comprehensive feasibility study is conducted on microgrid with SMR through electricity generation profiles, geographical and environmental assessment, as well as cost analysis using simulation practices and data analysis.Also potency of SMRs is analyzed. Parameters and Key Performance Indicators (KPIs) could be analyzed to achieve feasible solution of microgrids with small modular reactor (SMR) to improve the overall microgrid performance.The study shows that SMR could be a feasible solution if microgrid parameters are selected properly. (author)

  10. Technical Guidelines for Environmental Dredging of Contaminated Sediments

    Science.gov (United States)

    2008-09-01

    material from barges to adjacent rehandling facilities or to move material relatively short distances. Conveyors can also be used to transfer ...by direct dumping or unloading into a chute or conveyor . Truck transport of treated material to landfills may also be considered. The material...environmental dredging for purposes of a feasibility study, remedial design , and implementation. The scope of this document is limited to the technical

  11. Congeneration feasibility: Otis Elevator Company and Polychrome Corporation. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Fox, H.

    1982-05-01

    This report summarizes an investigation of the technical and economic feasibility of cogenerating electric and thermal power at two manufacturing plants (Otis Elevator Company and Polychrome Corporation) located on neighboring properties in Yonkers, NY. Existing electrical- and steam-producing equipment and energy consumption date are summarized. Alternative cases examined include electrical energy generation, electrical energy generation with waste heat recovery and a combined cycle case. Also reported are life cycle cost economic evaluations including simple payback period and return-on-investment indices. While it was concluded that cogeneration of heat and electricity at these industrial plant sites would not be economically viable, this detailed study provides valuable insight into the types of problems encountered when considering cogeneration feasibility.

  12. FEASIBILITY ANALYSIS OF BUSINESS "AMALIA BOUTIQUE"PTWARNA WARNI AMALIA AS MUSLIMAH FASHIONIN SOUTH JAKARTA

    Directory of Open Access Journals (Sweden)

    Dian Amalia Handayani

    2016-04-01

    Full Text Available This research aims to determine the feasibility of Muslimah fashion business "Amalia Boutique" by analyzing from several aspects including the legal aspects, environmental aspects, market aspects and marketing, technical and technological aspects, and aspects of human resource management, and financial aspects. Object of this study is "Amalia Boutique", is engaged in the business of fashion Muslimah. The design of this research is a descriptive study using qualitative techniques.Primary data collection techniques in this study is the observation to determine the location of Muslim fashion boutiques and stores in South Jakarta and the observation of the use of hijab. As for the secondary data obtained by researchers obtained from several sources such as the BPS, books, reports, journals, and the internet.The results of the analysis of the feasibility study "Amalia Boutique" is feasible when viewed from the sixth aspect.

  13. Technical feasibility and reliability of passive safety systems of AC600

    International Nuclear Information System (INIS)

    Niu, W.; Zeng, X.

    1996-01-01

    The first step conceptual design of the 600 MWe advanced PWR (AC-600) has been finished by the Nuclear Power Institute of China. Experiments on the passive system of AC-600 are being carried out, and are expected to be completed next year. The main research emphases of AC-600 conceptual design include the advanced core, the passive safety system and simplification. The design objective of AC-600 is that the safety, reliability, maintainability, operation cost and construction period are all improved upon compared to those of PWR plant. One of important means to achieve the objective is using a passive system, which has the following functions whenever its operation is required: providing the reactor core with enough coolant when others fail to make up the lost coolant; reactor residual heat removal; cooling and reducing pressure in the containment and preventing radioactive substances from being released into the environment after occurrence of accident (e.g. LOCA). The system should meet the single failure criterion, and keep operating when a single active component or passive component breaks down during the first 72 hour period after occurrence of accident, or in the long period following the 72 hour period. The passive safety system of AC-600 is composed of the primary safety injection system, the secondary emergency core residual heat removal system and the containment cooling system. The design of the system follows some relevant rules and criteria used by current PWR plant. The system has the ability to bear single failure, two complete separate subsystems are considered, each designed for 100% working capacity. Normal operation is separate from safety operation and avoids cross coupling and interference between systems, improves the reliability of components, and makes it easy to maintain, inspect and test the system. The paper discusses the technical feasibility and reliability of the passive safety system of AC-600, and some issues and test plans are also

  14. Technical feasibility and reliability of passive safety systems of AC600

    Energy Technology Data Exchange (ETDEWEB)

    Niu, W; Zeng, X [Nuclear Power Inst. of China, Chendu (China)

    1996-12-01

    The first step conceptual design of the 600 MWe advanced PWR (AC-600) has been finished. Experiments on the passive system of AC-600 are being carried out, and are expected to be completed next year. The main research emphases of AC-600 conceptual design include the advanced core, the passive safety system and simplification. The design objective of AC-600 is that the safety, reliability, maintainability, operation cost and construction period are all improved upon compared to those of PWR plant. One of important means to achieve the objective is using a passive system, which has the following functions whenever its operation is required: providing the reactor core with enough coolant when others fail to make up the lost coolant; reactor residual heat removal; cooling and reducing pressure in the containment and preventing radioactive substances from being released into the environment after occurrence of accident (e.g. LOCA). The system should meet the single failure criterion, and keep operating when a single active component or passive component breaks down during the first 72 hour period after occurrence of accident, or in the long period following the 72 hour period. The passive safety system of AC-600 is composed of the primary safety injection system, the secondary emergency core residual heat removal system and the containment cooling system. The design of the system follows some relevant rules and criteria used by current PWR plant. The system has the ability to bear single failure, two complete separate subsystems are considered, each designed for 100% working capacity. Normal operation is separate from safety operation and avoids cross coupling and interference between systems, improves the reliability of components, and makes it easy to maintain, inspect and test the system. The paper discusses the technical feasibility and reliability of the passive safety system of AC-600, and some issues and test plans are also involved. (author). 3 figs, 1 tab.

  15. TMI-2 fuel-recovery plant. Feasibility study

    International Nuclear Information System (INIS)

    Evans, D.L.

    1982-12-01

    This project is a feasibility study for constructing a TMI-2 core Fuel Recovery Plant at the Idaho National Engineering Laboratory (INEL). The primary objectives of the Fuel Recovery Plant (FRP) are to recover and account for the fuel and to process, isolate, and package the waste material from the TMI-2 core. This feasibility study is predicated on a baseline plant and covers its design, fabrication, installation, testing and operation. Alternative methods for the disposal of the TMI-2 core have also been considered, but not examined in detail for their feasibility. The FRP will receive TMI-2 fuel in canisters. The fuel will vary from core debris to intact fuel assemblies and include some core structural materials. The canister contents will be shredded and subsequently fed to a dissolver. Uranium, plutonium, fission products, and some core structural material will be dissolved. The uranium will be separated by solvent extraction and solidified by calcination. The plutonium will also be separated by solvent extraction and routed to the Plutonium Extraction Facility. The wastes will be packaged for further treatment, temporary storage or permanent disposal

  16. Feasibility study concerning remediation and rehabilitation of industrial polluted lands on the Absheron Peninsula, Republic of Azerbaijan

    Science.gov (United States)

    Pivin, Majorie; Helsen, Stefan; Cuyvers, Lars

    2014-05-01

    ECOREM is carrying out a feasibility study focused on the remediation and rehabilitation of industrial polluted lands, located on the Absheron Peninsula (Republic of Azerbaijan), on behalf of the State Oil Company of Azerbaijan Republic (SOCAR). The objective of this study is to support SOCAR with specific technologies and capacity building for environmental remediation works on various sectors of the Peninsula. As an independent consultancy company, ECOREM provides sustainable and quality advice, seeking the balance to the interests of the client and the environment in the broadest sense of the word. Within this study, it is important to underline that extraction activities in the country have been going on for more than a century. Given that the age of the environmental problems is equal to the history of the oil production, it is nearly impossible to point out the responsibilities of the various companies or to define the exact activities that occurred on a particular location. From the data gathered so far, more than 3600 ha of oil contaminated area are known in Baku and the Absheron Peninsula. Within this feasibility study, ECOREM will advice SOCAR on suitable and best available remediation technologies to apply on prior contaminated areas. According to the Environmental Policy of the Company, SOCAR would like to act in priority on the numerous contaminated lands of the Absheron Peninsula. Through the exploitation of the extensive GIS database provided by SOCAR, the oil contaminated sites will be examined in details in order to determine the most sensitive areas, on which remediation works or monitoring should be implemented in priority. To locate these sites, ECOREM will provide SOCAR with technical support in order to conduct risk analysis, remediation and monitoring of soil and/or groundwater oil pollutions. According to these results, practical solutions will be proposed concerning the possible reuse and management of contaminated soils and hazardous

  17. Feasibility study on improving SO/sub 2/ abatement economics through improvements in byproduct utilization. Final report. 2 Volumes

    Energy Technology Data Exchange (ETDEWEB)

    1984-01-17

    This study was undertaken to assess the technical feasibility of improving SO/sub 2/ abatement economics through improvements in byproduct utilization, and to recommend the most appropriate strategy for fostering the development and commericalization of such technology. Existing byproduct technology was reviewed and the potential for new technology assessed. This was done by a literature review and a survey of individuals and organizations actively engaged in this area. The assessment is confined to technical aspects only. This phase of the study concludes that there is a wide range of abatement byproduct technology, at various stages of development, which if appropriately exploited, offers the potential of improving byproduct utility and value, and hence the economics of Canadian SO/sub 2/ abatement. The second phase of this study addresses the problem of the most effective strategy for ensuring the development and commercialization of appropriate byproduct technology. This is based on discussions with individuals and organizations involved in the field, and assessment of the motivation and potential effectiveness of alternative approaches within the context of a diverse Canadian industry, the technology status in Canada and the national need. Includes 51-page bibliography. 400 refs., 14 tabs.

  18. Ute Mountain Ute Tribe Community-Scale Solar Feasibility Study

    Energy Technology Data Exchange (ETDEWEB)

    Rapp, Jim [Parametrix; Knight, Tawnie [Ute Mountain Ute Tribe

    2014-01-30

    Parametrix Inc. conducted a feasibility study for the Ute Mountain Ute Tribe to determine whether or not a community-scale solar farm would be feasible for the community. The important part of the study was to find where the best fit for the solar farm could be. In the end, a 3MW community-scale solar farm was found best fit with the location of two hayfield sites.

  19. Report on technical feasibility of underground pumped hydroelectric storage in a marble quarry site in the Northeast United States

    Energy Technology Data Exchange (ETDEWEB)

    Chas. T. Main, Inc.

    1982-03-01

    The technical and economic aspects of constructing a very high head underground hydroelectric pumped storage were examined at a prefeasibility level. Excavation of existing caverns in the West Rutland Vermont marble quarry would be used to construct the underground space. A plant capacity of 1200 MW and 12 h of continuous capacity were chosen as plant operating conditions. The site geology, plant design, and electrical and mechanical equipment required were considered. The study concluded that the cost of the 1200 MW underground pumped storage hydro electric project at this site even with the proposed savings from marketable material amounts to between $581 and $595 per kilowatt of installed capacity on a January 1982 pricing level. System studies performed by the planning group of the New England Power System indicate that the system could economically justify up to about $442 per kilowatt on an energy basis with no credit for capacity. To accommodate the plant with the least expensive pumping energy, a coal and nuclear generation mix of approximately 65% would have to be available before the project becomes feasible. It is not expected that this condition can be met before the year 2000 or beyond. It is therefore concluded that the West Rutland underground pumped storage facility is uneconomic at this time. Several variables however could have marked influence on future planning and should be examined on periodic basis.

  20. Virtual rehabilitation in a school setting: is it feasible for children with cerebral palsy?

    Science.gov (United States)

    Rosie, Juliet A; Ruhen, Shelley; Hing, Wayne A; Lewis, Gwyn N

    2015-01-01

    To determine the feasibility of a school-based virtual rehabilitation intervention for children with cerebral palsy. A feasibility study was conducted using a mixed method approach. Participants were five children with cerebral palsy who were currently attending a rural school. Each child received an 8-week rehabilitation programme involving an Interactive Virtual Reality Exercise (IREX) system. The IREX was placed in the child's school for the duration of the intervention. Each child's programme was designed by a physiotherapist but supervised by a teacher aide at the school. Feasibility of the intervention was assessed through a questionnaire completed by the child and an interview conducted with the teacher supervisor. The children all rated the IREX intervention as fun, easy to use, and beneficial for their arm. Categories from the supervisor interviews centred on resolving technical issues, the enjoyment of taking part due to the child's progress, and the central role of interacting with the child. Input from the research physiotherapist was critical to the success of the intervention. The IREX is feasible to implement in a school-based setting supervised by teachers. This provides an option for delivering physiotherapy to children in isolated areas who do not receive on-going therapy. Implication for Rehabilitation Virtual rehabilitation programmes using the IREX are feasible in a school-based setting. The negative impact of technical difficulties is likely to be overcome by the user's enjoyment and rehabilitation benefits gained. Input from a therapist in designing and monitoring the programme is critical.

  1. Multidisciplinary design optimization of large wind turbines—Technical, economic, and design challenges

    International Nuclear Information System (INIS)

    Ashuri, Turaj; Zaaijer, Michiel B.; Martins, Joaquim R.R.A.; Zhang, Jie

    2016-01-01

    Highlights: • 5, 10 and 20 MW wind turbines are developed using multidisciplinary design optimization. • Technical feasibility and economy of large wind turbines are investigated. • Critical upscaling trends of existing wind turbines are presented up to 20 MW. • Design challenges of large wind turbines are identified, and design solutions proposed. • With no design innovation, upscaling of existing turbines will increase the costs. - Abstract: Wind energy has experienced a continuous cost reduction in the last decades. A popular cost reduction technique is to increase the rated power of the wind turbine by making it larger. However, it is not clear whether further upscaling of the existing wind turbines beyond the 5–7 MW range is technically feasible and economically attractive. To address this question, this study uses 5, 10, and 20 MW wind turbines that are developed using multidisciplinary design optimization as upscaling data points. These wind turbines are upwind, 3-bladed, pitch-regulated, variable-speed machines with a tubular tower. Based on the design data and properties of these wind turbines, scaling trends such as loading, mass, and cost are developed. These trends are used to study the technical and economical aspects of upscaling and its impact on the design and cost. The results of this research show the technical feasibility of the existing wind turbines up to 20 MW, but the design of such an upscaled machine is cost prohibitive. Mass increase of the rotor is identified as a main design challenge to overcome. The results of this research support the development of alternative lightweight materials and design concepts such as a two-bladed downwind design for upscaling to remain a cost effective solution for future wind turbines.

  2. Feasibility Study of Economics and Performance of Solar Photovoltaics at the Santo Domingo Pueblo in Sandoval County, New Mexico

    Energy Technology Data Exchange (ETDEWEB)

    Geiger, J.; Lisell, L.; Mosey, G.

    2013-07-01

    The U.S. Environmental Protection Agency (EPA), in accordance with the RE-Powering America's Land initiative, selected the Pueblo of Santo Domingo in Sandoval County, New Mexico, for a renewable energy production feasibility study. The National Renewable Energy Laboratory (NREL) provided technical assistance for this project. The purpose of this report is to assess specific areas on the Pueblo for potential installation of photovoltaic (PV) systems and to estimate the cost, performance, and site impacts of different PV options. The report also recommends financing options that could assist in the implementation of these PV systems.

  3. Economic feasibility of food irradiation in the Philippines

    International Nuclear Information System (INIS)

    Singson, C.C.; De Guzman, Z.M.; Pasion, W.B.

    1991-01-01

    Food irradiation is not a new technology and is accepted in many countries. Market acceptance of irradiated foods is established and the importance of radiation to reduce post-harvest food losses, increase shelf-life and improve hygienic quality of foods has been recognized in Asia and the Pacific. Countries with strict quarantine restrictions, such as the United States and Japan, require treatment of fresh fruits and produce for insect pests disinfestation. Several studies have established the technical feasibility of using radiation to preserve some food items in the country such as mangoes, onions, garlic, black pepper, coffee, prawns and desiccated coconut. The aim of this study is to determine the feasibility of setting up an irradiation facility in the Philippines, to undertake the processing of selected food items especially those with good export potentials, to identify areas of concern vital to the success or failure of this type of undertaking and to make recommendations to enhance the viability of this project. (auth.). 13 refs.; appendices; 6 tabs

  4. Feasibility of ultrasound-guided intraarticular contrast injection for MR arthrography

    International Nuclear Information System (INIS)

    Baek, Soo Jin; Lee, Jong Min; Kang, Duck Sick

    2005-01-01

    To assess the feasibility of ultrasound-guided intraarticular contrast injection using the posterior approach for MR arthrography. Between June 2002 and October 2004, 132 patients (29 female, 103 male: mean age, 33.6 years) underwent ultrasound-guided intraarticular contrast media injection (40 ml saline + 10 ml 2% lidocaine + 0.2 ml gadopentetate dimeglumine + 0.4 ml epinephrine) for MR arthrography. The patients were classified into four groups, viz. the no leakage group, the minor leakage with successful intraarticular injection group, the major leakage with unsuccessful intraarticular injection group, and the injection failure group. The 'no leakage' and 'minor leakage' groups were considered to be technical successes, while the 'major leakage' and 'injection failure' groups were regarded as technical failures. The technical success rate of ultrasound-guided intraarticular contrast injection using the posterior approach for MR Arthrography was 99.2% (131/132 patients) and one patients 0.7% (1/132 patients) was included in the 'major leakage' group. Ultrasound-guided intraarticular contrast injection using the posterior approach for MR arthrography was feasible with a high success rate

  5. Feasibility of mHealth and Near Field Communication technology based medication adherence monitoring.

    Science.gov (United States)

    Morak, Juergen; Schwarz, Mark; Hayn, Dieter; Schreier, Guenter

    2012-01-01

    Poor patients' adherence to intake of prescribed medication has been identified as a serious problem in the treatment of chronically ill patients. Technical solutions are needed to measure and - if necessary - to increase the patients' adherence. A telemonitoring solution was developed to record a patient's medication intake based on smart blisters and mobile phones with NFC functionality. The components allowed recording of drug type, timestamp, and dosage of pills taken. The system's usability and technical feasibility was evaluated in the course of an application study. Over a period of 13 months 59 patients suffering from diabetes were monitored. 1,760 blisters were handed out to these patients and 14,843 takeout events were recorded and transmitted via mobile phone. Results indicate the feasibility of this concept to monitor adherence. Although the system still needs to be optimized for routine use it shows the potential for targeting the problem of poor patient adherence by NFC enabled devices.

  6. Final report on a study of coherence in acceptability criteria for the technical aspects of risks associated with potentially hazardous installations

    International Nuclear Information System (INIS)

    Chicken, J.C.

    1988-01-01

    This report describes the results of the study that was made, under Contract No ECI-1390-B7221-85D, for the European Atomic Energy Community. The aim of the study was to examine and assess the feasibility of developing coherent and uniform criteria for judging the acceptability of the technical aspects of the risks associated with potentially hazardous installations. The report is arranged in five main parts. First the nature of hazardous installations is considered and this provides the basis for examination of the currently-used technical risk acceptability criteria. Next, the possible forms of criteria are explored and then universally consistent partial and overall technical risk acceptability criteria are proposed. Following this the implications of using the criteria proposed at the design, regulatory and operating levels are examined. Then, by testing the criteria against some real decisions, the practical problems of using the proposed criteria are explored. This leads to consideration of possible alternatives to the proposed criteria. Finally the conclusions that appear to be justified are summarized and the need for further work is identified

  7. Telestroke ambulances in prehospital stroke management: concept and pilot feasibility study.

    Science.gov (United States)

    Liman, Thomas G; Winter, Benjamin; Waldschmidt, Carolin; Zerbe, Norman; Hufnagl, Peter; Audebert, Heinrich J; Endres, Matthias

    2012-08-01

    Pre- and intrahospital time delays are major concerns in acute stroke care. Telemedicine-equipped ambulances may improve time management and identify patients with stroke eligible for thrombolysis by an early prehospital stroke diagnosis. The aims of this study were (1) to develop a telestroke ambulance prototype; (2) to test the reliability of stroke severity assessment; and (3) to evaluate its feasibility in the prehospital emergency setting. Mobil, real-time audio-video streaming telemedicine devices were implemented into advanced life support ambulances. Feasibility of telestroke ambulances and reliability of the National Institutes of Health Stroke Scale assessment were tested using current wireless cellular communication technology (third generation) in a prehospital stroke scenario. Two stroke actors were trained in simulation of differing right and left middle cerebral artery stroke syndromes. National Institutes of Health Stroke Scale assessment was performed by a hospital-based stroke physician by telemedicine, by an emergency physician guided by telemedicine, and "a posteriori" on the basis of video documentation. In 18 of 30 scenarios, National Institutes of Health Stroke Scale assessment could not be performed due to absence or loss of audio-video signal. In the remaining 12 completed scenarios, interrater agreement of National Institutes of Health Stroke Scale examination between ambulance and hospital and ambulance and "a posteriori" video evaluation was moderate to good with weighted κ values of 0.69 (95% CI, 0.51-0.87) and 0.79 (95% CI, 0.59-0.98), respectively. Prehospital telestroke examination was not at an acceptable level for clinical use, at least on the basis of the used technology. Further technical development is needed before telestroke is applicable for prehospital stroke management during patient transport.

  8. An investigation into the technical feasibility of cyclotron production of technetium-99m

    International Nuclear Information System (INIS)

    Egan, G.F.; Lagunas-Solar, M.C.

    1994-01-01

    The role of technetium-99m in nuclear medicine is well established with 80 per cent to 90 per cent of all nuclear medicine studies utilising this isotope. Technetium-99m is currently produced from nuclear reactors via production of the parent radionuclide molybdenum-99. The reactor production of 99m Tc has both significant financial and environmental costs, with unresolved problems in the areas of radioactive waste disposal and reactor decommissioning. Recent scientific publications have indicated that medical quality 99m Tc may be produced using cyclotrons without having the associated problems of waste disposal and decommissioning. Further scientific research is now required to demonstrate the feasibility of this cyclotron production technique. A collaboration between the Cyclotron and PET Centre, Austin Hospital, the National Medical Cyclotron, ANSTO, Sydney, and the Crocker Nuclear Laboratory, University of California, Davis, USA has been proposed. The general objective of the proposed collaboration is to acquire additional scientific data to evaluate the 99m Tc cyclotron production method and to determine the feasibility of cyclotron technology for Australian nuclear medicine. 16 refs., 2 tabs

  9. Optoacoustic technique for noninvasive monitoring of blood oxygenation: a feasibility study

    Science.gov (United States)

    Esenaliev, Rinat O.; Larina, Irina V.; Larin, Kirill V.; Deyo, Donald J.; Motamedi, Massoud; Prough, Donald S.

    2002-08-01

    Replacement of invasive monitoring of cerebral venous oxygenation with noninvasive techniques offers great promise in the management of life-threatening neurologic illnesses including traumatic brain injury. We developed and built an optoacoustic system to noninvasively monitor cerebral venous oxygenation; the system includes a nanosecond Nd:YAG laser and a specially designed optoacoustic probe. We tested the system in vitro in sheep blood with experimentally varied oxygenation. Our results demonstrated that (1) the amplitude and temporal profile of the optoacoustic waves increase with blood oxygenation in the range from 24% to 92%, (2) optoacoustic signals can be detected despite optical and acoustic attenuation by thick bone, and (3) the system is capable of real-time and continuous measurements. These results suggest that the optoacoustic technique is technically feasible for continuous, noninvasive monitoring of cerebral venous oxygenation.

  10. The Economic Pre-feasibility Study of Madura Nuclear Desalination System

    International Nuclear Information System (INIS)

    Djoko-Birmanto, Moch; Suparman

    2004-01-01

    The feasibility study is needed in the planning of construction of NPPs SMART type coupled with desalination technology of MED tpe to produce clean water in Madura island. One important part of the feasibility study is the economical and financial analysis. The feasibility criteria of nuclear desalination project is analyzed by using the general parameters that is commonly used in evaluating a project, which is Financial Net Present Value (FNPV), Financial Internal Rate of Return (FIRR) and Payback Period. The calculation result shows that with the electricity selling price of 54.17 mills/KWh, for entirely project funded by the foreign loan, local loan and equity, it could be obtained FIRR 12.73 %, FNPV US$ 75.29 million and Payback Period is 8 years. By seeing from the project feasibility criteria, this nuclear desalination project can be feasible and the investment aspect shows that this project is beneficial because the capital return rate is rather high, the benefit in the end of the economic life-time is rather big and the capital payback period is fast. (author)

  11. Technical and economic feasibility for the application of micronized coal as a replacement for No. 2 oil for start-up and low-load operation at Illinois Power Havana No. 6 Cycling Unit

    International Nuclear Information System (INIS)

    Rosenberger, F.; Guilfoyle, C.J.; Parker, W.O. Jr.

    1991-01-01

    Uncertainty regarding oil availability and long-term price stability make it difficult for a utility to predict annual ignition costs for a cycling unit. Illinois Power Company, Sargent and Lundy Engineering and Micro-fuel Corporation have produced a detailed feasibility study on the application of micronized coal as a replacement fuel for start-up and low-load operation for Havana No. 6. This unit is a B and W opposed-fired boiler which is rated at 410 MWe (summer net). This paper presents technical and economic analysis, including the uncertainties of the application of this technology

  12. Image-guided intensity-modulated radiotherapy for patients with locally advanced gastric cancer: a clinical feasibility study.

    Science.gov (United States)

    Badakhshi, Harun; Gruen, Arne; Graf, Reinhold; Boehmer, Dirk; Budach, Volker

    2014-01-01

    The aim of this study was to determine the medical and technical feasibility of intensity-modulated radiotherapy (IMRT) in high-risk nonmetastatic gastric cancer stage II and III after primary gastrectomy and D2 lymphadenectomy. A prospective nonrandomized phase II trial was performed on 25 consecutive patients with gastric cancer with high risk (T3-4, N1-3, G2-3, R0-1). The dose delivered was 45 Gy (1.80 Gy per fraction) in IMRT technique. Concurrent 5-fluorouracil-based chemotherapy at 225 mg/m(2) was administered as a continuous intravenous infusion. Primary endpoints were acute gastrointestinal toxicity (CTC 4.0) and technical feasibility of IMRT in regard to dose planning and radiation delivery. Early acute events were defined as clinical and chemical adverse effects of IMRT and concurrent chemotherapy during treatment. By definition, 90 days after the end of IMRT has been evaluated as acute-phase toxicity. No patient had grade 4 or higher acute adverse events. Clinical grade 3 toxicity occurred in two patients (8%) with diarrhea and in one case (4%) with nausea. Hematological changes with grade 3 occurred in three cases (12%) with hemoglobin decrease, in five cases (25%) as leukopenia, and in one case (4%) with thrombocytopenia. The mean dose for liver was 16 Gy and the percentage volume exceeding 30 Gy (V30) was 21%. Mean dose for right and left kidney was 9 and 13 Gy, respectively, and V20 was 9% and 13%, respectively. Heart received a median dose of 15 Gy and V40 was 17%. The mean dose to the bowel was 11 Gy and V40 was 6%. Spinal cord had at maximum 33 Gy in median. Specifics of dose distribution, including the coverage, for the target region were as follows: minimum was 33 Gy, maximum 48.6 Gy, and mean dose 44.6 Gy. The prescribed dose (45 Gy) covered 99% and 95% of planning target volume (OTV) in 66% and 92% of cases, respectively. Median PTV was 15.77 ml (range, 805-3,604 ml). The data support the practical feasibility of IMRT in adjuvant treatment in

  13. Investigation of the feasibility of underground coal gasification in North Dakota, United States

    International Nuclear Information System (INIS)

    Pei, Peng; Nasah, Junior; Solc, Jaroslav; Korom, Scott F.; Laudal, Daniel; Barse, Kirtipal

    2016-01-01

    Highlights: • A four-year feasibility study of underground coal gasification is presented. • A test site was selected for feasibility investigation. • Gasification test, a hydrogeological study and geomechanical study were performed. • Results suggest favorable conditions for UCG development at the selected site. - Abstract: Underground coal gasification (UCG) is a promising technology that has the potential to recover currently-unmineable coal resources. The technical feasibility and economic success of a UCG project is highly site specific. Any risks associated with UCG, such as subsidence, groundwater contamination, and syngas quality, should be sufficiently evaluated through a feasibility study. This paper presents a four-year UCG feasibility study utilizing lignite seams in North Dakota, United States. Four wells were drilled through the lignite seams at a selected site, and lignite and strata cores were recovered. A geological model of the formation was built, coal and rock properties were analyzed, and field hydrogeological tests and laboratory gasification tests were performed. This work provided valuable insights in rock mechanics, hydrogeology, and coal properties. The study results show that the selected site is suitable for development of a UCG plant because there are minimal induced subsidence risks, there is hydrological isolation from major aquifers and the coal produces desirable syngas quality for liquid fuel production. Methodologies developed in this study will benefit the design, optimization and management of the UCG process.

  14. [A case study regarding the technical and public health feasibility of collecting water from fog].

    Science.gov (United States)

    García-Ubaque, César A; Vaca-Bohórquez, Martha L; García-Ubaque, Juan C

    2013-01-01

    Evaluating the collection of water for human consumption from fog nets in San Antonio (Cundinamarca department). Water was collected from fog using a prototype 6 m²sensor unit which was installed In the area for 53 days; this water was analysed to assess its quality regarding human consumption. The collection area's average daily volume was 43.26 L/day and the parameters evaluated met the minimum values established by local regulations for drinking water (RAS 2000), except for pH. This technique represents an alternative for obtaining water fit for human consumption and can be scaled-up to produce the quantity needed for communities living in low rainfall areas. It can thereby lead to improving such populations' health conditions. Its economic feasibility should thus be assessed regarding its implementation and sustainability.

  15. Technical and economical feasibility of the hybrid adsorption compression heat pump concept for industrial applications

    International Nuclear Information System (INIS)

    Pal, Michel van der; Wemmers, Anton; Smeding, Simon; Boer, Robert de

    2013-01-01

    Heat pump technologies offer a significant potential for primary energy savings in industrial processes. Thermally driven heat pumps can use waste heat as driving energy source to provide either heating or cooling. A chemi-sorption heat transformer can upgrade a waste heat source to temperatures of 150–200 °C. The specific heat transformer process however requires waste heat temperatures in the range of 120 °C, whereas waste heat sources of lower temperatures are more abundant. Using this lower temperature waste heat, and still reach the desired higher output temperatures can be achieved by the integration of a chemisorption and mechanical compression step in a single hybrid heat pump concept. This concept can offer an increased flexibility in temperatures, both for the waste heat source as for the heat delivery. The technical and economical feasibility of the proposed hybrid heat pump concept is evaluated. The range of operating temperatures of different chemi-sorption working pairs for as heat driven and as hybrid systems are defined, as well as their energy efficiencies. Investment costs for the hybrid systems are derived and payback times are calculated. The range of payback times is from 2 to 9 years and are strongly influenced by the number of operating hours, the electrical COP of the compression stage, and the energy prices

  16. Feasibility study on tandem fuel cycle

    International Nuclear Information System (INIS)

    Han, P.S.; Suh, I.S.; Rim, C.S.; Kim, B.K.; Suh, K.S.; Ro, S.K.; Juhn, P.I.; Kim, S.Y.

    1983-01-01

    The objective of this feasibility study is to review and assess the current state of technology concerning the tandem fuel cycle. Based on the results from this study, a long-term development plan suitable for Korea has been proposed for this cycle, i.e., the PWR → CANDU tandem fuel cycle which used plutonium and uranium, recovered from spent PWR fuel by co-processing, as fuel material for CANDU reactors. (Author)

  17. A feasibility study of the provision of a personalized interdisciplinary audiovisual summary to facilitate care transfer care at hospital discharge: Care Transfer Video (CareTV).

    Science.gov (United States)

    Newnham, Harvey H; Gibbs, Harry H; Ritchie, Edward S; Hitchcock, Karen I; Nagalingam, Vathy; Hoiles, Andrew; Wallace, Ed; Georgeson, Elizabeth; Holton, Sara

    2015-04-01

    To assess the feasibility and patient acceptance of a personalized interdisciplinary audiovisual record to facilitate effective communication with patients, family, carers and other healthcare workers at hospital discharge. Descriptive pilot study utilizing a study-specific patient feedback questionnaire conducted from October 2013 to June 2014. Twenty General Medical inpatients being discharged from an Acute General Medical Ward in a metropolitan teaching hospital. Audiovisual record of a CareTV filmed at the patient's bedside by a consultant-led interdisciplinary team, within 24 h prior to discharge from the ward, provided immediately for the patient to take home. Patient surveys were completed within 2 weeks of discharge. Technical quality, utilization, acceptability, patient satisfaction and recall of diagnosis, medication changes and post-discharge review arrangements. All patients had watched their CareTV either alone or in the presence of a variety of others: close family, their GP, a medical specialist, friends or other health personnel. Participating patients had good understanding of the video content and recall of their diagnosis, medication changes and post-discharge plans. Patient feedback was overwhelmingly positive. In the context of a General Medical Unit with extensive experience in interdisciplinary bedside rounding and teamwork, CareTV is simple to implement, inexpensive, technically feasible, requires minimal staff training and is acceptable to patients. The results of this pilot study will inform and indicate the feasibility of conducting a larger randomized control trial of the impact of CareTV on patient satisfaction, medication adherence and recall of key information, and primary healthcare provider satisfaction. © The Author 2015. Published by Oxford University Press in association with the International Society for Quality in Health Care; all rights reserved.

  18. Fast 3-T MR-guided transrectal prostate biopsy using an in-room tablet device for needle guide alignment: a feasibility study.

    Science.gov (United States)

    Overduin, Christiaan G; Heidkamp, Jan; Rothgang, Eva; Barentsz, Jelle O; de Lange, Frank; Fütterer, Jurgen J

    2018-05-22

    To assess the feasibility of adding a tablet device inside the scanner room to assist needle-guide alignment during magnetic resonance (MR)-guided transrectal prostate biopsy. Twenty patients with one cancer-suspicious region (CSR) with PI-RADS score ≥ 4 on diagnostic multiparametric MRI were prospectively enrolled. Two orthogonal scan planes of an MR fluoroscopy sequence (~3 images/s) were aligned to the CSR and needle-guide pivoting point. Targeting was achieved by manipulating the needle-guide under MR fluoroscopy feedback on the in-room tablet device. Technical feasibility and targeting success were assessed. Complications and biopsy procedure times were also recorded. Needle-guide alignment with the in-room tablet device was technically successful in all patients and allowed sampling after a single alignment step in 19/20 (95%) CSRs (median size 14 mm, range: 4-45). Biopsy cores contained cancer in 18/20 patients. There were no per-procedural or post-biopsy complications. Using the tablet device, the mean time to first biopsy was 5.8 ± 1.0 min and the mean total procedure time was 23.7 ± 4.1 min. Use of an in-room tablet device to assist needle-guide alignment was feasible and safe during MR-guided transrectal prostate biopsy. Initial experience indicates potential for procedure time reduction. • Performing MR-guided prostate biopsy using an in-room tablet device is feasible. • CSRs could be sampled after a single alignment step in 19/20 patients. • The mean procedure time for biopsy with the tablet device was 23.7 min.

  19. Virtual Sensorimotor Balance Training for Children With Fetal Alcohol Spectrum Disorders: Feasibility Study.

    Science.gov (United States)

    McCoy, Sarah Westcott; Jirikowic, Tracy; Price, Robert; Ciol, Marcia A; Hsu, Lin-Ya; Dellon, Brian; Kartin, Deborah

    2015-11-01

    Diminished sensory adaptation has been associated with poor balance control for children with fetal alcohol spectrum disorders (FASD). A virtual reality system, Sensorimotor Training to Affect Balance, Engagement and Learning (STABEL), was developed to train sensory control for balance. The purpose of this study was to examine the STABEL system in children with FASD and children with typical development (TD) to (1) determine the feasibility of the STABEL system and (2) explore the immediate effects of the STABEL system on sensory attention and postural control. This is a technical report with observational study data. Eleven children with FASD and 11 children with TD, aged 8 to 16 years, completed 30 minutes of STABEL training. The children answered questions about their experience using STABEL. Sensory attention and postural control were measured pre- and post-STABEL training with the Multimodal Balance Entrainment Response system and compared using repeated-measures analysis of variance. All children engaged in game play and tolerated controlled sensory input during the STABEL protocol. Immediate effects post-STABEL training in both groups were increased postural sway velocity and some changes in entrainment gain. Children with FASD showed higher entrainment gain to vestibular stimuli. There were no significant changes in sensory attention fractions. The small sample size, dose of STABEL training, and exploratory statistical analyses are study limitations, but findings warrant larger systematic study to examine therapeutic effects. Children completed the training protocol, demonstrating the feasibility of the STABEL system. Differences in postural sway velocity post-STABEL training may have been affected by fatigue, warranting further investigation. Limited immediate effects suggest more practice is needed to affect sensory attention; however, entrainment gain changes suggest the STABEL system provoked vestibular responses during balance practice. © 2015

  20. Energy Flexibility from Large Prosumers to Support Distribution System Operation—A Technical and Legal Case Study on the Amsterdam ArenA Stadium

    Directory of Open Access Journals (Sweden)

    Dirk Kuiken

    2018-01-01

    Full Text Available To deal with the rising integration of stochastic renewables and energy intensive distributed energy resources (DER to the electricity network, alternatives to expensive network reinforcements are increasingly needed. An alternative solution often under consideration is integrating flexibility from the consumer side to system management. However, such a solution needs to be contemplated from different angles before it can be implemented in practice. To this end, this article considers a case study of the Amsterdam ArenA stadium and its surrounding network where flexibility is expected to be available to support the network in the future. The article studies the technical aspects of using this flexibility to determine to what extent, despite the different, orthogonal goals, the available flexibility can be used by various stakeholders in scenarios with a large load from electric vehicle charging points. Furthermore, a legal study is performed to determine the feasibility of the technical solutions proposed by analysing current European Union (EU and Dutch law and focusing on the current agreements existing between the parties involved. The article shows that flexibility in the network provided by Amsterdam ArenA is able to significantly increase the number of charging points the network can accommodate. Nonetheless, while several uses of flexibility are feasible under current law, the use of flexibility provided by electric vehicles specifically faces several legal challenges in current arrangements.

  1. Non-technical skills assessment in surgery.

    Science.gov (United States)

    Sharma, Bharat; Mishra, Amit; Aggarwal, Rajesh; Grantcharov, Teodor P

    2011-09-01

    Adverse events in surgery have highlighted the importance of non-technical skills, such as communication, decision-making, teamwork, situational awareness and leadership, to effective organizational performance. These skills carry particular importance to surgical oncology, as members of a multidisciplinary team must work cohesively to formulate effective patient care plans. Several non-technical skills evaluation tools have been developed for use in surgery, without adequate comparison and consensus on which should be standard for training. Eleven articles describing the use of three non-technical evaluation tools related to surgery: NOTSS (Non Technical Skills for Surgeons), NOTECHS (Non Technical Skills) and OTAS (Observational Teamwork Assessment for Surgery) were analyzed with respect to scale formulation, validity, reliability and feasibility. Furthermore, their use in training thus far and the future of non-technical rating scales in surgical curricula was discussed. Future work should focus on incorporating these assessment tools into training and into a real operating room setting to provide formative evaluations for surgical residents. Copyright © 2010 Elsevier Ltd. All rights reserved.

  2. Technical Feasibility Evaluation on The Use of A Peltier Thermoelectric Module to Recover Automobile Exhaust Heat

    Science.gov (United States)

    Sugiartha, N.; Sastra Negara, P.

    2018-01-01

    A thermoelectric module composes of integrated p-n semiconductors as hot and cold side junctions and uses Seebeck effect between them to function as a thermoelectric generator (TEG) to directly convert heat into electrical power. Exhaust heat from engines as otherwise wasted to the atmosphere is one of the heat sources freely available to drive the TEG. This paper evaluates technical feasibility on the use of a Peltier thermoelectric module for energy recovery application of such kind of waste heat. An experimental apparatus has been setup to simulate real conditions of automobile engine exhaust piping system. It includes a square section aluminium ducting, an aluminium fin heat sink and a TEC1 12706 thermoelectric module. A heater and a cooling fan are employed to simulate hot exhaust gas and ambient air flows, respectively. Electrical loading is controlled by resistors. Dependent variables measured during the test are cold and hot side temperatures, open and loaded circuit output voltages and electrical current. The test results revealed a promising application of the Peltier thermoelectric module for the engine exhaust heat recovery, though the loaded output power produced and loaded output voltage are still far lower than the commercially thermoelectric module originally purposed for the TEG application.

  3. MacMillan Pier Transportation Center Feasibility Study.

    Science.gov (United States)

    2006-06-01

    The MacMillan Pier Transportation Center Feasibility Study examines two potential sites (landside and waterside) for a transportation center that provides a range of tourist and traveler information. It would serve as a gateway for Provincetown and t...

  4. The implementation of an AR (augmented reality) approach to support mammographic interpretation training: an initial feasibility study

    Science.gov (United States)

    Tang, Qiang; Chen, Yan; Gale, Alastair G.

    2017-03-01

    Appropriate feedback plays an important role in optimising mammographic interpretation training whilst also ensuring good interpretation performance. The traditional keyboard, mouse and workstation technical approach has a critical limitation in providing supplementary image-related information and providing complex feedback in real time. Augmented Reality (AR) provides a possible superior approach in this situation, as feedback can be provided directly overlaying the displayed mammographic images so making a generic approach which can also be vendor neutral. In this study, radiological feedback was dynamically remapped virtually into the real world, using perspective transformation, in order to provide a richer user experience in mammographic interpretation training. This is an initial attempt of an AR approach to dynamically superimpose pre-defined feedback information of a DICOM image on top of a radiologist's view, whilst the radiologist is examining images on a clinical workstation. The study demonstrates the feasibility of the approach, although there are limitations on interactive operations which are due to the hardware used. The results of this fully functional approach provide appropriate feedback/image correspondence in a simulated mammographic interpretation environment. Thus, it is argued that employing AR is a feasible way to provide rich feedback in the delivery of mammographic interpretation training.

  5. Feasibility study for siting of a deep repository within the Storuman municipality

    International Nuclear Information System (INIS)

    1995-01-01

    It is SKB's task to gather a broad body of information for the siting of a deep repository for Sweden's spent nuclear fuel and other long-lived radioactive waste. The criteria presented by SKB serve as guidelines for the siting studies. Overviews of siting factors are compiled in general siting studies of all or parts of Sweden. Feasibility studies examine the siting prospects in potentially suitable and interested municipalities. SKB plans to carry out feasibility studies in five to ten municipalities in different parts of the country. General studies and feasibility studies are primarily based on existing material. The feasibility study in Storuman is the first to be conducted. It began during the second half of 1993 with the conclusion of an agreement between the municipality and SKB. SKB has been in charge of the execution of the feasibility study. SKB has been responsible for the summary provided in a status report published in June 1994, as well as for the conclusions and evaluations in this final report. Altogether about 30 reports have been published within the framework of the feasibility study. The purpose of the various studies have been to describe, in as much detail as possible, the prospects for siting a deep repository in the municipality of Storuman, and to shed light on the possible positive and negative consequences of such a siting. The feasibility study has led to a discussion within the municipality and the region concerning the siting of a deep repository. In SKB's opinion, this gives all those concerned ample opportunity to become acquainted with the issues and to assert their interests and present their viewpoints at an early stage. 55 refs

  6. Feasibility study for the installation of photovoltaic cladding on the Shirehall, Shrewsbury

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-10-01

    The study has shown that it is technically feasible to overcome the problems with the existing mosaic cladding with the insulation of PV rainscreen cladding incorporating thermal insulation and to provide an acceptable, possibly enhanced, visual appearance. Panels which match the PV panels but provide no electrical output would be required in areas where PV panels would be inappropriate. This arrangement results in additional costs. The PV panels would produce an estimated 321,200 kWh/year of electricity and the improved insulation provided with the system would save an estimated 388,800 kWh/year of gas for heating giving savings of about UK pounds 19,000/year. The costs of installing the rainscreen cladding over and above that required for the straightforward replacement of the existing mosaic tiles would be approximately UK pounds 3 million. The savings in the use of electricity and gas arising from the use of the PV rainscreen incorporating thermal insulation are unlikely to be sufficient to satisfy the normal criteria for the provision of the capital investment required. (author)

  7. The feasibility of heat generating waste disposal into deep ocean sedimentary formations

    International Nuclear Information System (INIS)

    Murray, C.N.

    1986-01-01

    The paper briefly reviews the work undertaken to date by the Commission of European Communities ''Sub-Seabed Program'' in collaboration with national programmes of member countries. Special emphasis has been placed on the studies of the characteristics of deep ocean sediments to act as a barrier to the dispersion of radionuclides and the technical investigations carried out to demonstrate engineering feasibility of the option. (author)

  8. Three Affliated Tribes Renewable Energy Feasibility Study

    Energy Technology Data Exchange (ETDEWEB)

    Belvin Pete; Kent Good; Krista Gordon; Ed McCarthy,

    2006-05-26

    The Three Affliated Tribes on the Fort Berthold Reservation studied the feasibility of a commercial wind facility on land selected and owned by the Tribes and examined the potential for the development of renewable energy resources on Tribal Lands.

  9. Feasibility study of a clinically-integrated randomized trial of modifications to radical prostatectomy

    Directory of Open Access Journals (Sweden)

    Vickers Andrew J

    2012-02-01

    Full Text Available Abstract Background Numerous technical modifications to radical prostatectomy have been proposed. Such modifications are likely to lead to only slight improvements in outcomes. Although small differences would be worthwhile, an appropriately powered randomized trial would need to be very large, and thus of doubtful feasibility given the expense, complexity and regulatory burden of contemporary clinical trials. We have proposed a novel methodology, the clinically-integrated randomized trial, which dramatically streamlines trial procedures in order to reduce the marginal cost of an additional patient towards zero. We aimed to determine the feasibility of implementing such a trial for radical prostatectomy. Methods Patients undergoing radical prostatectomy as initial treatment for prostate cancer were randomized in a factorial design to involvement of the fascia during placement of the anastomotic sutures, urethral irrigation, both or neither. Endpoint data were obtained from routine clinical documentation. Accrual and compliance rates were monitored to determine the feasibility of the trial. Results From a total of 260 eligible patients, 154 (59% consented; 56 patients declined to participate, 20 were not approached on recommendation of the treating surgeon, and 30 were not approached for logistical reasons. Although recording by surgeons of the procedure used was incomplete (~80%, compliance with randomization was excellent when it was recorded, with only 6% of procedures inconsistent with allocation. Outcomes data was received from 71% of patients at one year. This improved to 83% as the trial progressed. Conclusions A clinically-integrated randomized trial was conducted at low cost, with excellent accrual, and acceptable compliance with treatment allocation and outcomes reporting. This demonstrates the feasibility of the methodology. Improved methods to ensure documentation of surgical procedures would be required before wider implementation

  10. An eHealth Application of Self-Reported Sports-Related Injuries and Illnesses in Paralympic Sport: Pilot Feasibility and Usability Study.

    Science.gov (United States)

    Fagher, Kristina; Jacobsson, Jenny; Dahlström, Örjan; Timpka, Toomas; Lexell, Jan

    2017-11-29

    requested, as the athletes perceived that injuries and illnesses often occurred because of the impairment. Options for description of multifactorial incidents including an injury, an illness, and the impairment were also insufficient. Few technical issues were encountered, but athletes with visual impairment reported usability difficulties with the speech synthesizer. An incidence rate of 1.8 injuries and 1.7 illnesses per 100 hours of athlete exposure were recorded. The weekly pain prevalence was 56% and the impairment contributed to 20% of the reported incidents. The novel eHealth-based application for self-reported SRIIPS developed and tested in this pilot study was generally feasible and usable. With some adaptation to accommodate Paralympic athletes' prerequisites and improved technical support for athletes with visual impairment, this application can be recommended for use in prospective studies of SRIIPS. ClinicalTrials.gov NCT02788500; https://clinicaltrials.gov/ct2/show/NCT02788500 (Archived by WebCite at http://www.webcitation.org/6v56OqTeP). ©Kristina Fagher, Jenny Jacobsson, Örjan Dahlström, Toomas Timpka, Jan Lexell. Originally published in JMIR Human Factors (http://humanfactors.jmir.org), 29.11.2017.

  11. An eHealth Application of Self-Reported Sports-Related Injuries and Illnesses in Paralympic Sport: Pilot Feasibility and Usability Study

    Science.gov (United States)

    2017-01-01

    related to the impairments were requested, as the athletes perceived that injuries and illnesses often occurred because of the impairment. Options for description of multifactorial incidents including an injury, an illness, and the impairment were also insufficient. Few technical issues were encountered, but athletes with visual impairment reported usability difficulties with the speech synthesizer. An incidence rate of 1.8 injuries and 1.7 illnesses per 100 hours of athlete exposure were recorded. The weekly pain prevalence was 56% and the impairment contributed to 20% of the reported incidents. Conclusions The novel eHealth-based application for self-reported SRIIPS developed and tested in this pilot study was generally feasible and usable. With some adaptation to accommodate Paralympic athletes’ prerequisites and improved technical support for athletes with visual impairment, this application can be recommended for use in prospective studies of SRIIPS. Trial Registration ClinicalTrials.gov NCT02788500; https://clinicaltrials.gov/ct2/show/NCT02788500 (Archived by WebCite at http://www.webcitation.org/6v56OqTeP) PMID:29187343

  12. Optimal power flow for technically feasible Energy Management systems in Islanded Microgrids

    DEFF Research Database (Denmark)

    Sanseverino, Eleonora Riva; T. T. Quynh, T.; Di Silvestre, Maria Luisa

    2016-01-01

    This paper presents a combined optimal energy and power flow management for islanded microgrids. The highest control level in this case will provide a feasible and optimized operating point around the economic optimum. In order to account for both unbalanced and balanced loads, the optimal power...... flow is carried out using a Glow-worm Swarm Optimizer. The control level is organized into two different sub-levels, the highest of which accounts for minimum cost operation and the lowest one solving the optimal power flow and devising the set points of inverter interfaced generation units...... and rotating machines with a minimum power loss. A test has been carried out for 6 bus islanded microgrids to show the efficiency and feasibility of the proposed technique....

  13. Technical Feasibility Assessment of LED Roadway Lighting on the Golden Gate Bridge

    Energy Technology Data Exchange (ETDEWEB)

    Tuenge, Jason R.

    2012-09-01

    Subsequent to preliminary investigations by the Golden Gate Bridge Highway & Transportation District (GGB), in coordination with Pacific Gas & Electric (PG&E), the GATEWAY Demonstration program was asked to evaluate the technical feasibility of replacing existing roadway lighting on the bridge with products utilizing LED technology. GGB and PG&E also indicated interest in induction (i.e., electrodeless fluorescent) technology, since both light source types feature rated lifetimes significantly exceeding those of the existing high-pressure sodium (HPS) and low-pressure sodium (LPS) products. The goal of the study was to identify any solutions which would reduce energy use and maintenance without compromising the quantity or quality of existing illumination. Products used for roadway lighting on the historic bridge must be installed within the existing amber-lensed shoebox-style luminaire housings. It was determined that induction technology does not appear to represent a viable alternative for the roadway luminaires in this application; any energy savings would be attributable to a reduction in light levels. Although no suitable LED retrofit kits were identified for installation within existing luminaire housings, several complete LED luminaires were found to offer energy savings of 6-18%, suggesting custom LED retrofit kits could be developed to match or exceed the performance of the existing shoeboxes. Luminaires utilizing ceramic metal halide (CMH) were also evaluated, and some were found to offer 28% energy savings, but these products might actually increase maintenance due to the shorter rated lamp life. Plasma technology was evaluated, as well, but no suitable products were identified. Analysis provided in this report was completed in May 2012. Although LED technologies are expected to become increasingly viable over time, and product mock-ups may reveal near-term solutions, some options not currently considered by GGB may ultimately merit evaluation. For

  14. Restoring effective sleep tranquility (REST): A feasibility and pilot study.

    Science.gov (United States)

    Eakman, Aaron M; Schmid, Arlene A; Henry, Kimberly L; Rolle, Natalie R; Schelly, Catherine; Pott, Christine E; Burns, Joshua E

    2017-06-01

    The purpose of this pilot study was to establish the feasibility of completing a future controlled trial of a multi-component cognitive behavioral therapy for insomnia program for military veterans with sleep disturbance. This was a single-arm feasibility and pilot study. Participants were United States post-9/11 veterans with service-connected injuries, university students, and had self-reported sleep disturbances. Restoring Effective Sleep Tranquility was a multi-component cognitive behavioral therapy for insomnia intervention consisting of seven sessions of group therapy and eight 1:1 sessions delivered by occupational therapists. Feasibility and pilot indicators were process, resources, management, and scientific, including pre-post-assessments of sleep difficulties, dysfunctional sleep beliefs, participation, and pain interference. Indicators were supportive of feasibility, including reduced sleep difficulties (for example Medical Outcomes Study Sleep Measure [ t  = 3.29, p  = .02]), reduced nightmares: t  = 2.79, p  = .03; fewer dysfunctional sleep beliefs: t  = 3.63, p  = .01, and greater ability to participate in social roles: t  = -2.86, p  = .03, along with trends towards improved satisfaction with participation and reduced pain interference. The Restoring Effective Sleep Tranquility program may reduce sleep difficulties and improve participation in US veterans with service-connected injuries, and evidence indicates a controlled trial would be feasible to deliver.

  15. Planning for gasification of cellulosic wastes: Issues, feasibility and case study

    International Nuclear Information System (INIS)

    Staniewski, M.E.

    1993-01-01

    Gasification is presented as a concept that can assist municipalities and private companies to reduce the amount of solid waste generated and to utilize the cellulosic fraction of such waste as a biofuel. The technical and economic feasibility of cellulosic waste gasification is examined along with the implications associated with the environmental, social, and regulatory issues within a planning context. Study methods included a literature review, survey research employing nonstructured interviews, and a case study analysis. Opportunities for gasification are focused on regional governments in Ontario. The case study concentrated on the Regional Municipality of Waterloo. Regional governments in Ontario can benefit from utilizing the gasification concept to achieve a substantial reduction in the waste stream in an environmentally sound manner and contribute to solving worldwide problems associated with fossil fuel utilization. However, provincial and public acceptance will affect regional government decisions regarding gasification. Separate legislation should be enacted distinguishing gasification from incineration. In addition, the effectiveness of the environmental approval process must be improved; present procedures consume excess time and resources and act to discourage the involvement of public and private proponents. Public acceptance is likely to be affected by negative experiences associated with solid waste combustion. Nonbiased, reliable information is needed to clarify doubts and stress gasification's potential benefits. 85 refs., 15 figs., 26 tabs

  16. Zumbro Hydroelectric Project: installation of third unit. Feasibility assessment report

    Energy Technology Data Exchange (ETDEWEB)

    Williamson, James V.

    1979-03-01

    The feasibility of adding a third generating unit at an existing hydro power plant near Rochester, Minn. was examined considering the economic, technical, and environmental aspects. Installation of the unit, aiming at an Oct. 1983 completion date, is recommended. (LCL)

  17. Feasibility Study on HYSOL CSP

    DEFF Research Database (Denmark)

    Nielsen, Lars Henrik; Baldini, Mattia; Skytte, Klaus

    2016-01-01

    integrated HYSOL concept, therefore, becomes a fully dispatchable (offering firm power) and fully renewable energy source (RES) based power supply alternative, offering CO2-free electricity in regions with sufficient solar resources. The economic feasibility of HYSOL configurations is addressed in this paper....... The CO2 free HYSOL alternative is discussed relative to conventional reference firm power generation technologies. In particular the HYSOL performance relative to new power plants based on natural gas (NG) such as open cycle or combined cycle gas turbines (OCGT or CCGT) are in focus. The feasibility...

  18. Feasibility study for siting of a deep repository within the Storuman municipality

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-01-01

    It is SKB`s task to gather a broad body of information for the siting of a deep repository for Sweden`s spent nuclear fuel and other long-lived radioactive waste. The criteria presented by SKB serve as guidelines for the siting studies. Overviews of siting factors are compiled in general siting studies of all or parts of Sweden. Feasibility studies examine the siting prospects in potentially suitable and interested municipalities. SKB plans to carry out feasibility studies in five to ten municipalities in different parts of the country. General studies and feasibility studies are primarily based on existing material. The feasibility study in Storuman is the first to be conducted. It began during the second half of 1993 with the conclusion of an agreement between the municipality and SKB. SKB has been in charge of the execution of the feasibility study. SKB has been responsible for the summary provided in a status report published in June 1994, as well as for the conclusions and evaluations in this final report. Altogether about 30 reports have been published within the framework of the feasibility study. The purpose of the various studies have been to describe, in as much detail as possible, the prospects for siting a deep repository in the municipality of Storuman, and to shed light on the possible positive and negative consequences of such a siting. The feasibility study has led to a discussion within the municipality and the region concerning the siting of a deep repository. In SKB`s opinion, this gives all those concerned ample opportunity to become acquainted with the issues and to assert their interests and present their viewpoints at an early stage. 55 refs.

  19. Feasibility study for the partial conversion of a hydropower plant into a pumped-storage power plant: a case study of hydroelectric power plant La Barca (Asturias, Spain

    Directory of Open Access Journals (Sweden)

    E. Antuña Yudego

    2017-01-01

    Full Text Available Renewable energy sources have reported an unprecedented increase of global installed renewable power capacity. Against the advantages provided by this renewable power generation technology it should be taken into account an important issue: these intermittent energy sources supply a fluctuating output which is difficult to manage. Pumped-storage hydro power plants reappear in these circumstances as an efficient form of energy storage which allows to use reserves when necessary, enabling power generation output to cover continuously this energy demand. The present paper shows a simplified feasibility study of the partial conversion of hydropower plant La Barca, in Asturias, into a reversible storage through the development of an algorithm to simulate its operation according to electricity market prices. For this purpose, the operation in the deviation management market is considered and the technical modifications required for the conversion are shown. The estimation of costs and incomes present a feasible scenario.

  20. Feasibility study on naturally safe HTGR (NSHTR) for air ingress accident

    Energy Technology Data Exchange (ETDEWEB)

    Ohashi, Hirofumi, E-mail: ohashi.hirofumi@jaea.go.jp; Sato, Hiroyuki; Tachibana, Yukio; Kunitomi, Kazuhiko; Ogawa, Masuro

    2014-05-01

    A new design activity for an advanced reactor, referred to as a naturally safe high temperature gas-cooled reactor (NSHTR), has been launched by authors after the accident at the Fukushima Daiichi Nuclear Power Station. The concept of NSHTR is that the release of radioactive materials is kept at very low level and no harmful effect on people and the environment is ensured by only physical phenomena even in the absence of engineered safety features. At an air ingress accident, possible physical events that lead to the loss or degradation of the confinement function of the fuel-coating layers are the crack of the coatings caused by the explosion of carbon monoxide (CO) produced by the graphite oxidation and failure of the coatings by melting or sublimation caused by core heat up due to the reaction heat of the graphite oxidation. In this study, the CO concentration and the heat generated by graphite oxidation inside the circular tube were evaluated parametrically using a steady-state one-dimensional model to confirm the feasibility of NSHTR at a severe condition of the air ingress accident (i.e., a massive air ingress by simultaneous rupture of two primary pipes). It was confirmed that the CO concentration at the outlet of coolant channel can be maintained below the explosion limit due to the reaction with oxygen in the air, and the reaction heat can be removed with the decay heat by physical phenomena under certain conditions of the coolant channel geometry without any engineered safety features. The results revealed that the design of NSHTR is technically feasible in terms of the suppression of the CO explosion and the heat removal of the reaction heat at the air ingress accident.

  1. WERF MACT Feasibility Study Report

    Energy Technology Data Exchange (ETDEWEB)

    B. Bonnema; D. Moser; J. Riedesel; K. Kooda; K. Liekhus; K. Rebish; S. Poling

    1998-11-01

    This study was undertaken to determine the technical feasibility of upgrading the Waste Experimental Reduction Facility (WERF) at the Idaho National Engineering and Environmental Laboratory to meet the offgas emission limits proposed in the Maximum Achievable Control Technologies (MACT)rule. Four practicable offgas treatment processes were identified, which, if installed, would enable the WERF to meet the anticipated MACT emission limits for dioxins and furans (D/F), hydrochloric acid (HCI), and mercury (Hg). Due to the three-year time restraint for MACT compliance, any technology chosen for the upgrade must be performed within the general plant project funding limit of $5 M. The option selected consists of a partial-quench evaporative cooler with dry sorbent injection for HCI removal followed by a sulfur-impregnated activated carbon bed for Hg control. The planning cost estimate for implementing the option is $4.17 M (with 24% contingency). The total estimated cost includes capital costs, design and construction costs, and project management costs. Capital costs include the purchase of a new offgas evaporative cooler, a dry sorbent injection system with reagent storage, a new fabric filter baghouse, a fixed carbon bed absorber, and two offgas induced draft exhaust fans. It is estimated that 21 months will be required to complete the recommended modification to the WERF. The partial-quench cooler is designed to rapidly cool the offgas exiting the secondary combustion chamber to minimize D/F formation. Dry sorbent injection of an alkali reagent into the offgas is recommended. The alkali reacts with the HCI to form a salt, which is captured with the fly ash in the baghouse. A design HCI removal efficiency of 97.2% allows for the feeding 20 lbs/hr of chlorine to the WERF incinerator. The sorbent feed rate can be adjusted to achieve the desired HCI removal efficiency. A fixed bed of sulfur-impregnated carbon was conservatively sized for a total Hg removal capacity when

  2. Engineering feasibility analysis for in-situ stabilization of Canonsburg residues

    International Nuclear Information System (INIS)

    1982-01-01

    The US Department of Energy is considering several methods for carrying out remedial actions in Canonsburg, Pennsylvania, at the site of an inactive uranium-processing mill. The main objective of this study is to determine the feasibility of in-situ stabilization as the remedial action. In-situ stabilization is an alternative to site decontamination and offsite disposal. The problems associated with offsite hauling of large quantities of contaminated material and with the location and development of a new disposal site could be avoided by the implementation of an in-situ stabilization concept. In addition, the in-situ approach would be more cost-effective than offsite disposal. This study will establish that a technically feasible and implementable in-situ stabilization concept can be developed that meets regulatory requirements and is cost effective. This study in no way commits the DOE to implement any specific actions described herein. 11 refs., 30 figs., 24 tabs

  3. Structural Design Feasibility Study for the Global Climate Experiment

    Energy Technology Data Exchange (ETDEWEB)

    Lewin,K.F.; Nagy, J.

    2008-12-01

    Neon, Inc. is proposing to establish a Global Change Experiment (GCE) Facility to increase our understanding of how ecological systems differ in their vulnerability to changes in climate and other relevant global change drivers, as well as provide the mechanistic basis for forecasting ecological change in the future. The experimental design was initially envisioned to consist of two complementary components; (A) a multi-factor experiment manipulating CO{sub 2}, temperature and water availability and (B) a water balance experiment. As the design analysis and cost estimates progressed, it became clear that (1) the technical difficulties of obtaining tight temperature control and maintaining elevated atmospheric carbon dioxide levels within an enclosure were greater than had been expected and (2) the envisioned study would not fit into the expected budget envelope if this was done in a partially or completely enclosed structure. After discussions between NEON management, the GCE science team, and Keith Lewin, NEON, Inc. requested Keith Lewin to expand the scope of this design study to include open-field exposure systems. In order to develop the GCE design to the point where it can be presented within a proposal for funding, a feasibility study of climate manipulation structures must be conducted to determine design approaches and rough cost estimates, and to identify advantages and disadvantages of these approaches including the associated experimental artifacts. NEON, Inc requested this design study in order to develop concepts for the climate manipulation structures to support the NEON Global Climate Experiment. This study summarizes the design concepts considered for constructing and operating the GCE Facility and their associated construction, maintenance and operations costs. Comparisons and comments about experimental artifacts, construction challenges and operational uncertainties are provided to assist in selecting the final facility design. The overall goal

  4. Non-Technical Skills for Surgeons (NOTSS): Critical appraisal of its measurement properties.

    Science.gov (United States)

    Jung, James J; Borkhoff, Cornelia M; Jüni, Peter; Grantcharov, Teodor P

    2018-02-17

    To critically appraise the development and measurement properties, including sensibility, reliability, and validity of the Non-Technical Skills of Surgeons (NOTSS) system. Articles that described development process of the NOTSS system were identified. Relevant primary studies that presented evidence of reliability and validity were identified through a comprehensive literature review. NOTSS was developed through robust item generation and reduction strategies. It was shown to have good content validity, acceptability, and feasibility. Inter-rater reliability increased with greater expertise and number of assessors. Studies demonstrated evidence of cross-sectional construct validity, in that the tool was able to differentiate known groups of varied non-technical skill levels. Evidence of longitudinal construct validity also existed to demonstrate that NOTSS detected changes in non-technical skills before and after targeted training. In populations and settings presented in our critical appraisal, NOTSS provided reliable and valid measurements of intraoperative non-technical skills of surgeons. Copyright © 2018 Elsevier Inc. All rights reserved.

  5. The Feasibility and Validity of a Remote Pulse Oximetry System for Pulmonary Rehabilitation: A Pilot Study

    Directory of Open Access Journals (Sweden)

    Jonathan Tang

    2012-01-01

    Full Text Available Pulmonary rehabilitation is an effective treatment for people with chronic obstructive pulmonary disease. However, access to these services is limited especially in rural and remote areas. Telerehabilitation has the potential to deliver pulmonary rehabilitation programs to these communities. The aim of this study was threefold: to establish the technical feasibility of transmitting real-time pulse oximetry data, determine the validity of remote measurements compared to conventional face-to-face measures, and evaluate the participants’ perception of the usability of the technology. Thirty-seven healthy individuals participated in a single remote pulmonary rehabilitation exercise session, conducted using the eHAB telerehabilitation system. Validity was assessed by comparing the participant's oxygen saturation and heart rate with the data set received at the therapist’s remote location. There was an 80% exact agreement between participant and therapist data sets. The mean absolute difference and Bland and Altman’s limits of agreement fell within the minimum clinically important difference for both oxygen saturation and heart rate values. Participants found the system easy to use and felt confident that they would be able to use it at home. Remote measurement of pulse oximetry data for a pulmonary rehabilitation exercise session was feasible and valid when compared to conventional face-to-face methods.

  6. Security analysis of socio-technical physical systems

    NARCIS (Netherlands)

    Lenzini, Gabriele; Mauw, Sjouke; Ouchani, Samir

    2015-01-01

    Recent initiatives that evaluate the security of physical systems with objects as assets and people as agents – here called socio-technical physical systems – have limitations: their agent behavior is too simple, they just estimate feasibility and not the likelihood of attacks, or they do estimate

  7. Surgical timing after chemoradiotherapy for rectal cancer, analysis of technique (STARRCAT): results of a feasibility multi-centre randomized controlled trial.

    Science.gov (United States)

    Foster, J D; Ewings, P; Falk, S; Cooper, E J; Roach, H; West, N P; Williams-Yesson, B A; Hanna, G B; Francis, N K

    2016-10-01

    The optimal time of rectal resection after long-course chemoradiotherapy (CRT) remains unclear. A feasibility study was undertaken for a multi-centre randomized controlled trial evaluating the impact of the interval after chemoradiotherapy on the technical complexity of surgery. Patients with rectal cancer were randomized to either a 6- or 12-week interval between CRT and surgery between June 2012 and May 2014 (ISRCTN registration number: 88843062). For blinded technical complexity assessment, the Observational Clinical Human Reliability Analysis technique was used to quantify technical errors enacted within video recordings of operations. Other measured outcomes included resection completeness, specimen quality, radiological down-staging, tumour cell density down-staging and surgeon-reported technical complexity. Thirty-one patients were enrolled: 15 were randomized to 6 and 16-12 weeks across 7 centres. Fewer eligible patients were identified than had been predicted. Of 23 patients who underwent resection, mean 12.3 errors were observed per case at 6 weeks vs. 10.7 at 12 weeks (p = 0.401). Other measured outcomes were similar between groups. The feasibility of measurement of operative performance of rectal cancer surgery as an endpoint was confirmed in this exploratory study. Recruitment of sufficient numbers of patients represented a challenge, and a proportion of patients did not proceed to resection surgery. These results suggest that interval after CRT may not substantially impact upon surgical technical performance.

  8. Feasibility study: Assess the feasibility of siting a monitored retrievable storage facility

    International Nuclear Information System (INIS)

    King, J.W.

    1993-01-01

    The purpose of phase one of this study are: To understand the waste management system and a monitored retrievable storage facility; and to determine whether the applicant has real interest in pursuing the feasibility assessment process. Contents of this report are: Generating electric power; facts about exposure to radiation; handling storage, and transportation techniques; description of a proposed monitored retrievable storage facility; and benefits to be received by host jurisdiction

  9. Feasibility Study for a Hopi Utility-Scale Wind Project

    Energy Technology Data Exchange (ETDEWEB)

    Kendrick Lomayestewa

    2011-05-31

    The goal of this project was to investigate the feasibility for the generation of energy from wind and to parallel this work with the development of a tribal utility organization capable of undertaking potential joint ventures in utility businesses and projects on the Hopi reservation. The goal of this project was to investigate the feasibility for the generation of energy from wind and to parallel this work with the development of a tribal utility organization capable of undertaking potential joint ventures in utility businesses and projects on the Hopi reservation. Wind resource assessments were conducted at two study sites on Hopi fee simple lands located south of the city of Winslow. Reports from the study were recently completed and have not been compared to any existing historical wind data nor have they been processed under any wind assessment models to determine the output performance and the project economics of turbines at the wind study sites. Ongoing analysis of the wind data and project modeling will determine the feasibility of a tribal utility-scale wind energy generation.

  10. INTEC High-Level Waste Studies Universal Solvent Extraction Feasibility Study

    International Nuclear Information System (INIS)

    Banaee, J.; Barnes, C.M.; Battisti, T.; Herrmann, S.; Losinski, S.J.; McBride, S.

    2000-01-01

    This report summarizes a feasibility study that has been conducted on the Universal Solvent Extraction (UNEX) Process for treatment and disposal of 4.3 million liters of INEEL sodium-bearing waste located at the Idaho Nuclear Technology and Engineering Center. This feasibility study covers two scenarios of treatment. The first, the UNEX Process, partitions the Cs/Sr from the SBW and creates remote-handled LLW and contact-handled TRU waste forms. Phase one of this study, covered in the 30% review documents, dealt with defining the processes and defining the major unit operations. The second phase of the project, contained in the 60% review, expanded on the application of the UNEX processes and included facility requirements and definitions. Two facility options were investigated for the UNEX process, resulting in a 2 x 2 matrix of process/facility scenarios as follows: Option A, UNEX at Greenfield Facility, Option B, Modified UNEX at Greenfield Facility, Option C, UNEX at NWCF, th is document, covers life-cycle costs for all options presented along with results and conclusions determined from the study

  11. PV solar system feasibility study

    International Nuclear Information System (INIS)

    Ashhab, Moh’d Sami S.; Kaylani, Hazem; Abdallah, Abdallah

    2013-01-01

    Highlights: ► This research studies the feasibility of PV solar systems. ► The aim is to develop the theory and application of a hybrid system. ► Relevant research topics are reviewed and some of them are discussed in details. ► A prototype of the PV solar system is designed and built. - Abstract: This research studies the feasibility of PV solar systems and aims at developing the theory and application of a hybrid system that utilizes PV solar system and another supporting source of energy to provide affordable heating and air conditioning. Relevant research topics are reviewed and some of them are discussed in details. Solar heating and air conditioning research and technology exist in many developed countries. To date, the used solar energy has been proved to be inefficient. Solar energy is an abundant source of energy in Jordan and the Middle East; with increasing prices of oil this source is becoming more attractive alternative. A good candidate for the other system is absorption. The overall system is designed such that it utilizes solar energy as a main source. When the solar energy becomes insufficient, electricity or diesel source kicks in. A prototype of the PV solar system that operates an air conditioning unit is built and proper measurements are collected through a data logging system. The measured data are plotted and discussed, and conclusions regarding the system performance are extracted.

  12. Testing objective measures of motor impairment in early Parkinson's disease: Feasibility study of an at-home testing device.

    Science.gov (United States)

    Goetz, Christopher G; Stebbins, Glenn T; Wolff, David; DeLeeuw, William; Bronte-Stewart, Helen; Elble, Rodger; Hallett, Mark; Nutt, John; Ramig, Lorraine; Sanger, Terence; Wu, Allan D; Kraus, Peter H; Blasucci, Lucia M; Shamim, Ejaz A; Sethi, Kapil D; Spielman, Jennifer; Kubota, Ken; Grove, Andrew S; Dishman, Eric; Taylor, C Barr

    2009-03-15

    We tested the feasibility of a computer based at-home testing device (AHTD) in early-stage, unmedicated Parkinson's disease (PD) patients over 6 months. We measured compliance, technical reliability, and patient satisfaction to weekly assessments of tremor, small and large muscle bradykinesia, speech, reaction/movement times, and complex motor control. relative to the UPDRS motor score. The AHTD is a 6.5'' x 10'' computerized assessment battery. Data are stored on a USB memory stick and sent by internet to a central data repository as encrypted data packets. Although not designed or powered to measure change, the study collected data to observe patterns relative to UPDRS motor scores. Fifty-two PD patients enrolled, and 50 completed the 6 month trial, 48 remaining without medication. Patients complied with 90.6% of weekly 30-minute assessments, and 98.5% of data packets were successfully transmitted and decrypted. On a 100-point scale, patient satisfaction with the program at study end was 87.2 (range: 80-100). UPDRS motor scores significantly worsened over 6 months, and trends for worsening over time occurred for alternating finger taps (P = 0.08), tremor (P = 0.06) and speech (P = 0.11). Change in tremor was a significant predictor of change in UPDRS (P = 0.047) and was detected in the first month of the study. This new computer-based technology offers a feasible format for assessing PD-related impairment from home. The high patient compliance and satisfaction suggest the feasibility of its incorporation into larger clinical trials, especially when travel is difficult and early changes or frequent data collection are considered important to document.

  13. Integrating patient reported outcomes with clinical cancer registry data: a feasibility study of the electronic Patient-Reported Outcomes From Cancer Survivors (ePOCS) system.

    Science.gov (United States)

    Ashley, Laura; Jones, Helen; Thomas, James; Newsham, Alex; Downing, Amy; Morris, Eva; Brown, Julia; Velikova, Galina; Forman, David; Wright, Penny

    2013-10-25

    Routine measurement of Patient Reported Outcomes (PROs) linked with clinical data across the patient pathway is increasingly important for informing future care planning. The innovative electronic Patient-reported Outcomes from Cancer Survivors (ePOCS) system was developed to integrate PROs, collected online at specified post-diagnostic time-points, with clinical and treatment data in cancer registries. This study tested the technical and clinical feasibility of ePOCS by running the system with a sample of potentially curable breast, colorectal, and prostate cancer patients in their first 15 months post diagnosis. Patients completed questionnaires comprising multiple Patient Reported Outcome Measures (PROMs) via ePOCS within 6 months (T1), and at 9 (T2) and 15 (T3) months, post diagnosis. Feasibility outcomes included system informatics performance, patient recruitment, retention, representativeness and questionnaire completion (response rate), patient feedback, and administration burden involved in running the system. ePOCS ran efficiently with few technical problems. Patient participation was 55.21% (636/1152) overall, although varied by approach mode, and was considerably higher among patients approached face-to-face (61.4%, 490/798) than by telephone (48.8%, 21/43) or letter (41.0%, 125/305). Older and less affluent patients were less likely to join (both Pplanning and for targeting service provision.

  14. Fiscal 2000 regional new energy vision formulation - Financially aided project. Report on regional new energy vision formulation for Ueno village (Object of survey: Commercialization feasibility study for a stand-alone type wind power generation system at Ueno German Culture Village); 2000 nendo Uenoson chiiki shin energy vision sakutei hokokusho. Ueno Doitsu bunkamura dokuritsugata furyoku hatsuden system jigyoka feasibility study chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-02-01

    A survey is conducted about the profitability of installing a stand-alone type wind power system at Ueno village (Miyako Island), Okinawa Prefecture. The German Culture Village, which is an integrated resort house provided with accommodations (500 people), educational and cultural facilities, and sports facilities consumes 272 MWh/year in electric power. The results of the survey are summarized in six chapters, which are (1) the survey of the business under the project to be the object of feasibility study, (2) project to be the object of feasibility study, (3) outline of the Okinawa Electric Power Co., Inc., Miyakojima system and problems to ensue from its interconnection with wind turbines, (4) survey of stand-alone type wind turbine power generation systems, (5) technical/economic feasibility study, and (6) project management and future tasks. It is concluded that there will be profit in the presence of a subsidy that covers 65% or more of the total cost of constructing a system comprising three 600 KW wind turbines, three 400 kW class diesel generators, and storage batteries. (NEDO)

  15. Partitioning and transmutation - Technical feasibility, proliferation resistance and safeguardability

    International Nuclear Information System (INIS)

    Schenkel, R.; Glatz, J.-P.; Magill, J.; Mayer, K.

    2001-01-01

    Full text: The advantages of partitioning and transmutation (P and T) of minor actinides and selected fission products are largely discussed and described in literature. The advantages of separation of the long-lived alpha-emitters for the long-term storage of highly radioactive waste have been highlighted. After separation, these nuclides shall be transmuted by means of a dedicated reactor or accelerator driven system into shorter-lived fission products that are less hazardous. This, however, requires the development and implementation of a P and T fuel cycle, involving chemical separation of the minor actinides and the fabrication of MA containing fuels or targets. Concepts for P and T fuel cycles have been developed and technical issues are being addressed in various research programs. With the recognition of the proliferation potential associated with the minor actinides by the IAEA, also the proliferation and safeguards aspects need to be addressed. It is important to raise these points at an early stage of process development, in order to identify potential problems and to develop appropriate solutions. The oxide fuels used worldwide in thermal reactor systems for energy production are reprocessed by aqueous techniques. Therefore these systems, primarily the PUREX process, are fully developed and implemented commercially. Furthermore, the safeguards approach is fully implemented in existing facilities, covering uranium and plutonium. Pyroprocess systems have largely been associated with fast reactors and metallic fuels and their development has therefore only reached the pilot-scale stage and the feasibility of minor actinide (MA) separation still needs to be demonstrated. Hydrometallurgical and pyrochemical reprocessing should however not be considered as competing but rather as complementary technologies. For instance in a so-called double strata concept (foreseen for instance in the Japanese OMEGA project), the PUREX process (first stratum) would be

  16. Feasibility and utility of transradial cerebral angiography: experience during the learning period

    International Nuclear Information System (INIS)

    Kim, Ji Hyung; Park, Yong Sung; Chung, Chul Gu; Park, Kyeong Sug; Chung, Dong Jin; Kim, Hyun Jin

    2006-01-01

    We wanted to present our experiences for performing transradial cerebral angiography during the learning period, and we also wanted to demonstrate this procedure's technical feasibility and utility in various clinical situations. Thirty-two patients were enrolled in the study. All of them had unfavorable situations for performing transfemoral angiography, i.e., IV lines in the bilateral femoral vein, a phobia for groin puncture, decreased blood platelet counts, large hematoma or bruise, atherosclerosis in the bilateral femoral artery and the insistence of patients for choosing another procedure. After con firming the patency of the ulnar artery with a modified Allen's test and a pulse oximeter, the procedure was done using a 21-G micorpuncture set and 5-F Simon II catheters. After angiography, hemostasis was achieved with 1-2 minutes of manual compression and the subsequent application of a hospital-made wrist brace for two hours. The technical feasibility and procedure-related immediate and delayed complications were evaluated. The procedure was successful in 30/32 patients (93.8%). Failure occurred in two patients; one patient had hypoplasia of the radial artery and one patient had vasospasm following multiple puncture trials for the radial artery. Transradial cerebral angiography was technically feasible without significant difficulties even though it was tried during the learning period. Pain in the forearm or arm developed in some patients during the procedures, but this was usually mild and transient. Procedure-related immediate complications included severe bruising in one patient and a small hematoma in one patient. Any clinically significant complication or delayed complication such as radial artery occlusion was not demonstrated in our series. Transradial cerebral angiography is a useful alternative for the patients who have unfavorable clinical situations or contraindications for performing transfemoral cerebral angiography. For the experienced

  17. Feasibility and utility of transradial cerebral angiography: experience during the learning period

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Ji Hyung; Park, Yong Sung; Chung, Chul Gu; Park, Kyeong Sug; Chung, Dong Jin; Kim, Hyun Jin [Konyang University Hospital, Daejeon (Korea, Republic of)

    2006-03-15

    We wanted to present our experiences for performing transradial cerebral angiography during the learning period, and we also wanted to demonstrate this procedure's technical feasibility and utility in various clinical situations. Thirty-two patients were enrolled in the study. All of them had unfavorable situations for performing transfemoral angiography, i.e., IV lines in the bilateral femoral vein, a phobia for groin puncture, decreased blood platelet counts, large hematoma or bruise, atherosclerosis in the bilateral femoral artery and the insistence of patients for choosing another procedure. After con firming the patency of the ulnar artery with a modified Allen's test and a pulse oximeter, the procedure was done using a 21-G micorpuncture set and 5-F Simon II catheters. After angiography, hemostasis was achieved with 1-2 minutes of manual compression and the subsequent application of a hospital-made wrist brace for two hours. The technical feasibility and procedure-related immediate and delayed complications were evaluated. The procedure was successful in 30/32 patients (93.8%). Failure occurred in two patients; one patient had hypoplasia of the radial artery and one patient had vasospasm following multiple puncture trials for the radial artery. Transradial cerebral angiography was technically feasible without significant difficulties even though it was tried during the learning period. Pain in the forearm or arm developed in some patients during the procedures, but this was usually mild and transient. Procedure-related immediate complications included severe bruising in one patient and a small hematoma in one patient. Any clinically significant complication or delayed complication such as radial artery occlusion was not demonstrated in our series. Transradial cerebral angiography is a useful alternative for the patients who have unfavorable clinical situations or contraindications for performing transfemoral cerebral angiography. For the experienced

  18. Feasibility study on volcanic power generation system

    Energy Technology Data Exchange (ETDEWEB)

    None

    1977-07-01

    Investigations were carried out to determine the feasibility of volcanic power generation on Satsuma Io Island. Earthquakes were studied, as were the eruptions of subaerial and submarine hot springs. Hydrothermal rock alteration was studied and electrical surveys were made. General geophysical surveying was performed with thermocameras and radiation monitoring equipment. In particular, the Toyoba mine was studied, both with respect to its hot spring and its subsurface temperatures.

  19. Feasibility of extracting data from electronic medical records for research: an international comparative study.

    Science.gov (United States)

    van Velthoven, Michelle Helena; Mastellos, Nikolaos; Majeed, Azeem; O'Donoghue, John; Car, Josip

    2016-07-13

    Electronic medical records (EMR) offer a major potential for secondary use of data for research which can improve the safety, quality and efficiency of healthcare. They also enable the measurement of disease burden at the population level. However, the extent to which this is feasible in different countries is not well known. This study aimed to: 1) assess information governance procedures for extracting data from EMR in 16 countries; and 2) explore the extent of EMR adoption and the quality and consistency of EMR data in 7 countries, using management of diabetes type 2 patients as an exemplar. We included 16 countries from Australia, Asia, the Middle East, and Europe to the Americas. We undertook a multi-method approach including both an online literature review and structured interviews with 59 stakeholders, including 25 physicians, 23 academics, 7 EMR providers, and 4 information commissioners. Data were analysed and synthesised thematically considering the most relevant issues. We found that procedures for information governance, levels of adoption and data quality varied across the countries studied. The required time and ease of obtaining approval also varies widely. While some countries seem ready for secondary uses of data from EMR, in other countries several barriers were found, including limited experience with using EMR data for research, lack of standard policies and procedures, bureaucracy, confidentiality, data security concerns, technical issues and costs. This is the first international comparative study to shed light on the feasibility of extracting EMR data across a number of countries. The study will inform future discussions and development of policies that aim to accelerate the adoption of EMR systems in high and middle income countries and seize the rich potential for secondary use of data arising from the use of EMR solutions.

  20. Selling Technology in Technical Advertisements: A Case Study.

    Science.gov (United States)

    Guthrie, James R.

    1995-01-01

    Argues that, as the category of "technical products" has expanded and the public's enthusiasm for such products has lessened, marketing writers have begun to reconsider their approaches to technology in ads. Studies two technical ads in detail, and compares the ways in which they portray technology. (SR)

  1. Single-step simultaneous side-by-side placement of a self-expandable metallic stent with a 6-Fr delivery system for unresectable malignant hilar biliary obstruction: a feasibility study.

    Science.gov (United States)

    Kawakubo, Kazumichi; Kawakami, Hiroshi; Kuwatani, Masaki; Kudo, Taiki; Abe, Yoko; Kawahata, Shuhei; Kubo, Kimitoshi; Kubota, Yoshimasa; Sakamoto, Naoya

    2015-02-01

    Bilateral self-expandable metallic stent (SEMS) placement for the management of unresectable malignant hilar biliary obstruction (UMHBO) is technically challenging to perform using the existing metallic stents with thick delivery systems. The recently developed 6-Fr delivery systems could facilitate a single-step simultaneous side-by-side placement through the accessory channel of the duodenoscope. The aim of this study was to evaluate the feasibility of this procedure. Between May and September 2013, 13 consecutive patients with UMHBO underwent a single-step simultaneous side-by-side placement of SEMS with the 6-Fr delivery system. The technical success rate, stent patency, and rate of complications were evaluated from the prospectively collected database. Technical success was achieved in 11 (84.6%, 95% confidence interval [CI]: 57.8-95.8) patients. The median procedure time was 25 min. Early and late complications were observed in 23% (one segmental cholangitis and two liver abscesses) and 15% (one segmental cholangitis and one cholecystitis) patients, respectively. Median dysfunction free patency was 263 days (95% CI: 37-263). Five patients (38%) experienced stent occlusion that was successfully managed by endoscopic stent placement. A single-step simultaneous side-by-side placement of SEMS with a 6-Fr delivery system was feasible for the management of UMHBO. © 2014 Japanese Society of Hepato-Biliary-Pancreatic Surgery.

  2. IPNS upgrade: A feasibility study

    International Nuclear Information System (INIS)

    1995-04-01

    Many of Argonne National Laboratory's (ANL's) scientific staff members were very active in R ampersand D work related to accelerator-based spoliation sources in the 1970s and early 1980s. In 1984, the Seitz/Eastman Panel of the National Academy of Sciences reviewed U.S. materials science research facilities. One of the recommendations of this panel was that the United States build a reactor-based steady-state source, the Advanced Neutron Source (ANS), at Oak Ridge National Laboratory. Subsequently, R ampersand D activities related to the design of an accelerator-based source assumed a lower priority. The resumption of pulsed-source studies in this country started simultaneously with design activities in Europe aimed at the European Spallation Source (ESS). The European Community funded a workshop in September 1991 to define the parameters of the ESS. Participants in this workshop included both accelerator builders and neutron source users. A consortium of European countries has proposed to build a 5-MW pulsed source, and a feasibility study is currently under way. Soon after the birth of the ESS, a small group at ANL set about bringing themselves up to date on pulsed-source information since 1984 and studied the feasibility of upgrading ANL's Intense Pulsed Neutron Source (IPNS) to 1 MW by means of a rapidly cycling synchrotron that could be housed, along with its support facilities, in existing buildings. In early 1993, the Kohn panel recommended that (1) design and construction of the ANS should be completed according to the proposed project schedule and (2) development of competitive proposals for cost-effective design and construction of a 1-MW pulsed spallation source should be authorized immediately

  3. IPNS upgrade: A feasibility study

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-04-01

    Many of Argonne National Laboratory`s (ANL`s) scientific staff members were very active in R&D work related to accelerator-based spoliation sources in the 1970s and early 1980s. In 1984, the Seitz/Eastman Panel of the National Academy of Sciences reviewed U.S. materials science research facilities. One of the recommendations of this panel was that the United States build a reactor-based steady-state source, the Advanced Neutron Source (ANS), at Oak Ridge National Laboratory. Subsequently, R&D activities related to the design of an accelerator-based source assumed a lower priority. The resumption of pulsed-source studies in this country started simultaneously with design activities in Europe aimed at the European Spallation Source (ESS). The European Community funded a workshop in September 1991 to define the parameters of the ESS. Participants in this workshop included both accelerator builders and neutron source users. A consortium of European countries has proposed to build a 5-MW pulsed source, and a feasibility study is currently under way. Soon after the birth of the ESS, a small group at ANL set about bringing themselves up to date on pulsed-source information since 1984 and studied the feasibility of upgrading ANL`s Intense Pulsed Neutron Source (IPNS) to 1 MW by means of a rapidly cycling synchrotron that could be housed, along with its support facilities, in existing buildings. In early 1993, the Kohn panel recommended that (1) design and construction of the ANS should be completed according to the proposed project schedule and (2) development of competitive proposals for cost-effective design and construction of a 1-MW pulsed spallation source should be authorized immediately.

  4. Technical Feasibility of Integrated Laboratory in Faculty of Sports Science Universitas Negeri Semarang

    Directory of Open Access Journals (Sweden)

    Ipang Setiawan

    2017-11-01

    Full Text Available This research aims to analyze the requirements of technical integrated laboratory FIK Unnes in improving sports achievement in Central Java Province, Indonesia. Research method used in this research was qualitative descriptive, with evaluation approach, the instrument used document analysis, observation, interview and inquiry. Data analysis used by using Miles and Huberman interactive cycle then the pattern tendency was explained, qualitative analysis was initiated by describing reality happened in narration form then it was interpreted by a guidebook with ISO 17025 or SNI 17025 standard in laboratory. The result shows that the requirements of technical integrated laboratory FIK Unnes was quite maximum to contribute in improving sports achievement in Central Java Province, Indonesia, it was based on the technical standard from equipment, personnel, accommodation and environment condition, finding of test and measurement, quality assurance of measurement and test result, and reporting of result conducted based on ISO 17025 or SNI 17025 standard.

  5. CT colonography after colostomy - clinical application and technical feasibility

    International Nuclear Information System (INIS)

    Nedevska, A.

    2013-01-01

    Full text:Introduction: The aim of this study was to evaluate the clinical application and technical implementation of computed tomographic (CT ) colonoscopy in patients undergoing sigmoid or rectal resection and following sigmoid colostomy in the course of standard diagnostic postoperative follow-up and prior to the reconstructive colon surgery. Materials and Methods: The study included 48 patients who underwent anterior abdomen-perineal or rectal resection and subsequent sigmoid colostomy in case of sigma or rectum carcinoma. The pre-procedure bowel preparation included a full colon cleansing and barium-based fecal tagging. The balloon catheter (18 F) is placed in the colonic stoma. The balloon is insufflated with 15-30 ml saline or air. The balloon was gently pulled until opening of the stoma has been closed completely. In 15 patients, a second catheter was placed in the remaining rectum. Contrast scanning in supination was done for all patients. An additional scanning in left and right lateral position was necessary for 9 patients. Results: All studies were carried out without any major complications. All patients tolerated the intubation and insufflation of air into the intestinal lumen. Two patients (4%) have evaluated the examination as uncomfortable. In 6 patients (12.5 %) it was impossible to evaluate the intestinal segments because due to a collapse of the wall. Five of them were localized in the descending colon. In 5 patients there was a significant amount of residual intestinal contents. The fecal tagging and intravenous contrast enhancing allowed the assessment of these intestinal segments. The rectal residue was correctly assessed in all patients in terms of length, position and wall changes. Conclusion: CT colonoscopy is applicable after sigmostoma in patients with abdomen-perineal and anterior rectal resection. Further in-depth studies are needed to determine the clinical indications and reliability of the method

  6. Conducting feasibilities in clinical trials: An investment to ensure a good study

    Directory of Open Access Journals (Sweden)

    Viraj Rajadhyaksha

    2010-01-01

    Full Text Available Conducting clinical trial feasibility is one of the first steps in clinical trial conduct. This process includes assessing internal and environmental capacity, alignment of the clinical trial in terms of study design, dose of investigational product, comparator, patient type, with the local environment and assessing potential of conducting clinical trial in a specific country. A robust feasibility also ensures a realistic assessment and capability to conduct the clinical trial. For local affiliates of pharmaceutical organizations, and contract research organizations, this is a precursor to study placement and influences the decision of study placement. This article provides details on different types of feasibilities, information which is to be included and relevance of each. The article also aims to provide practical hands-on suggestions to make feasibilities more realistic and informative.

  7. Conducting feasibilities in clinical trials: an investment to ensure a good study.

    Science.gov (United States)

    Rajadhyaksha, Viraj

    2010-07-01

    Conducting clinical trial feasibility is one of the first steps in clinical trial conduct. This process includes assessing internal and environmental capacity, alignment of the clinical trial in terms of study design, dose of investigational product, comparator, patient type, with the local environment and assessing potential of conducting clinical trial in a specific country. A robust feasibility also ensures a realistic assessment and capability to conduct the clinical trial. For local affiliates of pharmaceutical organizations, and contract research organizations, this is a precursor to study placement and influences the decision of study placement. This article provides details on different types of feasibilities, information which is to be included and relevance of each. The article also aims to provide practical hands-on suggestions to make feasibilities more realistic and informative.

  8. Feasible Application Area Study for Linear Laser Cutting in Paper Making Processes

    Science.gov (United States)

    Happonen, A.; Stepanov, A.; Piili, H.

    Traditional industry sectors, like paper making industry, tend to stay within well-known technology rather than going forward towards promising, but still quite new technical solutions and applications. This study analyses the feasibility of the laser cutting in large-scale industrial paper making processes. Aim was to reveal development and process related challenges and improvement potential in paper making processes by utilizing laser technology. This study has been carried out, because there still seems to be only few large-scale industrial laser processing applications in paper converting processes worldwide, even in the beginning of 2010's. Because of this, the small-scale use of lasers in paper material manufacturing industry is related to a shortage of well-known and widely available published research articles and published measurement data (e.g. actual achieved cut speeds with high quality cut edges, set-up times and so on). It was concluded that laser cutting has strong potential in industrial applications for paper making industries. This potential includes quality improvements and a competitive advantage for paper machine manufacturers and industry. The innovations have also added potential, when developing new paper products. An example of these kinds of products are ones with printed intelligence, which could be a new business opportunity for the paper industries all around the world.

  9. Indicative criteria for assessing the feasibility of hydrogenerators modernization services; Criterios indicativos para analise da viabilidade de servicos de modernizacao de hidrogeradores

    Energy Technology Data Exchange (ETDEWEB)

    Pinto, Luciano Lopes [Universidade Federal de Itajuba (UNIFEI), MG (Brazil). Programa de Mestrado de Engenharia da Energia; Centrais Eletricas Brasileiras S.A. (ELETROBRAS), Rio de Janeiro, RJ (Brazil)], E-mail: lucianol@furnas.com.br; Tiago Filho, Geraldo Lucio [Universidade Federal de Itajuba (UNIFEI), MG (Brazil)], E-mail: tiago@unifei.edu.br; Gregati, Augusto Cezar Mileo [Companhia Paulista de Forca e Luz (CPFL), Sao Paulo, SP (Brazil)], E-mail: agregatti@baesa.com.br

    2010-10-15

    Aiming at helping the generating agents in direct actions for the development of new feasibility studies for implementation of the modernization of hydrogenerator, with the technological age over 30 (thirty) years, it presents evaluation criteria based on strategic parameters, operating income and availability. This criterion allows the analysis of the technical, operational, commercial and environmental issues involved in the feasibility study for modernization of hydrogenerator information available for the application of the theory, consolidated through diagnostic director. (author)

  10. Refurbishment of Railroad Crossties : A Technical and Economic Analysis

    Science.gov (United States)

    1977-12-01

    An analysis of the principal modes of failure for wooden railroad crossties was conducted and an evaluation of the technical and economic feasibility of refurbishing these ties was conducted. Among the principal modes of structural deterioration, onl...

  11. Analysis of Investment Feasibility to Pedestrian Bridge in Muara Teweh - Jingah

    Directory of Open Access Journals (Sweden)

    Laode Abd. Rahman

    2017-12-01

    Full Text Available The research aimed to analyze the needs of the construction of the Crossing Bridge of Muara Teweh - Jingah. The type of the research including the applied research was research concerning the application of theory to solve certain problems. The location of this research was at the Bridge Crossing of Muara Teweh - Jingah in North Barito District. Data analysis technique was feasibility study. The result of the research showed that 1 the construction of the Crossing Bridge of Muara Teweh - Jingah is needed to reduce the traffic density the traffic of the daily transportation in the development area has an effort to balance the traffic volume with road capacity in order to avoid LOS decrease and increase peoples prosperity level 2 the celebration of the construction of Muara Teweh - Jingah Crossing Bridge in terms of technical and economic and cultural aspects is stated to have fulfilled the feasibility 3 the feasibility of bridge development in terms of economic and cultural aspects is fulfilled because the value of BCR is greater than 1.0 and interest rate that is applicable is equal to 12 in 2015. Finally the bridge construction is feasible to be implemented.

  12. Technical and Economical Feasibility of Production of Ethanol from Sugar Cane and Sugar Cane Bagasse

    NARCIS (Netherlands)

    Efe, C.; Straathof, A.J.J.; Van der Wielen, L.A.M.

    2005-01-01

    The primary aim of this study is to investigate and analyze the sugar-ethanol plants operating in Brazil to construct a raw model to gain better understanding and insight about the technical and economical aspects of the currently operating plants. And, the secondary aim is to combine the knowledge

  13. Nuclear powered ships. Findings from a feasibility study

    International Nuclear Information System (INIS)

    Namikawa, Shunichiro; Maerli, Morten Bremer; Hoffmann, Peter Nyegaard; Brodin, Erik

    2011-01-01

    Nuclear shipping is attractive for several reasons, one of which is its positive effect on emissions (CO 2 , NOx and SOx). The benefits, however, do not come without risks of possible harmful effects on humans and wildlife. Nuclear ships set themselves apart from conventional ships, as well as from on-shore nuclear power-plants, on several counts. 1) The reactor-unit are non-stationary, and the reactor is subject to the ship motions. 2) Ship reactors must be compact due to space constraints. 3) Special design considerations are required to ensure reactor safety and security, as well as to enable refuelling. 4) A naval nuclear fuel cycle infrastructure for fuel fabrication, handling, and disposal is needed. Technological feasibility of nuclear shipping is by itself inconclusive to a expansion into civilian applications and use. Civilian nuclear propulsion needs to be commercially viable and politically acceptable. Appropriate legislation must be in place, and nuclear shipping concepts with proven safety records and highest possible nuclear proliferation-resistance must be established. Possible 'showstoppers' to a viable nuclear civilian shipping industry are outlined in the paper in view of Political, Technical, Regulatory, Commercial, Safety and Security aspects. Further, different types of ships with different propulsion system are compared in lights of life cycle cost and air emission. (author)

  14. Biodiesel feasibility study: An evaluation of material compatibility; performance; emission and engine durability

    Energy Technology Data Exchange (ETDEWEB)

    Fazal, M.A.; Haseeb, A.S.M.A.; Masjuki, H.H. [Department of Mechanical Engineering, University of Malaya, 50603 Kuala Lumpur (Malaysia)

    2011-02-15

    Biodiesel, derived from the transesterification of vegetable oils or animal fats, is composed of saturated and unsaturated long-chain fatty acid alkyl esters. In spite of having some application problems, recently it is being considered as one of the most promising alternative fuels in internal combustion engine. From scientific literatures, this paper has collected and analyzed the data on both advantages and disadvantages of biodiesel over conventional diesel. Since the aim of this study is to evaluate the biodiesel feasibility in automobiles, the first section is dedicated to materials compatibility in biodiesel as compared to that in diesel. The highest consensus is related to enhanced corrosion of automotive parts due to its compositional differences. In the subsequent sections, data on performance, emission and engine durability have been analyzed and compared. In this case, the highest consensus is found in reducing emissions as well as in increasing moving parts sticking, injector coking and filter plugging. This paper has also summarized the factors of biodiesel in contributing these technical performances. (author)

  15. Feasibility studies on macroscopic separation of carbon isotopes by IR laser chemistry - a technical report

    International Nuclear Information System (INIS)

    Mathi, P.; Nayak, A.K.; Parthasarathy, V.; Abhinandan, L.; Sarkar, S.K.

    2007-11-01

    This report describes the feasibility studies for macroscopic separation of carbon isotopes (∼ 50% enrichment level) by infrared multiphoton dissociation (IRMPD) of Freon - 22 (CF 2 HCl) using a 10Hz pulsed carbon dioxide laser in a large volume (∼ 300 litre) photochemical reactor (PCR). After a general introduction to the objective, the importance of characterization studies with a 10 Hz CO 2 laser is brought out before large scale operation in the PCR is carried out. The laboratory scale results obtained in a small cell with a lower average power (0.5 W) CO 2 laser is verified with a higher power (10 W) laser under optimal conditions. Such an exercise helps in understanding of any anomalies of the results and for applying the appropriate corrective measures while scaling up. The report deals with the design details, fabrication, installation and commissioning of the major components of the setup namely laser system, photochemical reactor, low temperature distillation unit and preparative gas chromatograph for realizing the targeted task. It further describes the standardization methodology of a sensitive analytical technique using quadrupole mass spectrometry (QMS) to ascertain the C 2 F 4 product quality (i.e. enrichment). A pre- concentration method for separating C 2 F 4 from CF 2 HCl using gas chromatography has been developed for very low-level mass spectral analysis. During this exercise, an indigenous QMS developed in VPID (erstwhile MS and ES) has also been benchmarked by comparing its performance with a commercial QMS unit. The report gives in details the operational experience of carrying out the large scale enrichment task in a batch process. The modular PCR employing a multi-pass refocusing Herriott optics for efficient photon utilization and gas blower arrangement for gas circulation during laser photolysis has given a typical production rate of about 10 mg/hr for total carbon with a 13 C isotopic purity of ∼ 40%. It further indicates the scope

  16. Alpha radioimmunotherapy of multiple myeloma: study of feasibility of ex vivo medullary purge

    International Nuclear Information System (INIS)

    Couturier, O.; Filippovitch, I.V.; Sorokina, N.I.; Cherel, M.; Thedrez, P.; Faivre-Chauvet, A.; Chatal, J.F.

    1997-01-01

    The efficiency of the radioimmunotherapy (RIT) using beta emitters has been clinically proved in treatments of refractory forms of lymphoma. The alpha-emitting radioelements of short half-life are also good potential candidates for RIT, applicable to tumor targets accessible rapidly to the molecules of the radio-immuno-conjugates of size compatible with the short range of alpha particles (50 to 80 μm). The goal of this study is to demonstrate the feasibility of such an approach on a model of myeloma multiply targeted by specific antibodies (B-B4) coupled to bismuth-213 with a chelating agent (benzyl-DTPA). The efficiency of the alpha RIT was evaluated in vitro by means of different techniques analyzing the cellular mortality (the method of limited dilution), the effects on DNA (the testing of micro-nuclei), the analysis of radio-induced apoptosis (the test with acridine orange) and finally the study of non-specific irradiation on population of cells of hematopoietic system un-recognized by the B-B4 benzyl-DTPA) immuno-conjugate. The first results have shown besides the technical feasibility of the project a strong dose dependent cellular mortality with a survival falling rapidly from 28% to around 1 o/oo for a single doubling of the dose from 14.8 kBq / 10 5 cells (0.4 μCi) to 29.6 kBq/10 5 cells (0.8 μCi). The cellular mortality was total at 300 kBq/10 5 cells (8 μCi). The cells in an apoptosis state were evidenced at rates up to 40% for a dose of 7.4 kBq/10 5 cells (0.2 μ Ci). New experiments will permit confirming these first results and determining the irradiation range having in view a utilization in protocols of purging of the myeloma cells on pockets obtained after plasmaphereses

  17. Livingston Parish Landfill Methane Recovery Project (Feasibility Study)

    Energy Technology Data Exchange (ETDEWEB)

    White, Steven

    2012-11-15

    The Woodside Landfill is owned by Livingston Parish, Louisiana and is operated under contract by Waste Management of Louisiana LLC. This public owner/private operator partnership is commonplace in the solid waste industry today. The landfill has been in operation since approximately 1988 and has a permitted capacity of approximately 41 million cubic yards. Based on an assumed in-place waste density of 0.94 ton per cubic yard, the landfill could have an expected design capacity of 39.3 million tons. The landfill does have an active landfill gas collection and control system (LFGCCS) in place because it meets the minimum thresholds for the New Source Performance Standards (NSPS). The initial LFGCS was installed prior to 2006 and subsequent phases were installed in 2007 and 2010. The Parish received a grant from the United States Department of Energy in 2009 to evaluate the potential for landfill gas recovery and utilization at the Woodside Landfill. This includes a technical and economic feasibility study of a project to install a landfill gas to energy (LFGTE) plant and to compare alternative technologies. The LFGTE plant can take the form of on-site electrical generation, a direct use/medium Btu option, or a high-Btu upgrade technology. The technical evaluation in Section 2 of this report concludes that landfill gas from the Woodside landfill is suitable for recovery and utilization. The financial evaluations in sections 3, 4, and 5 of this report provide financial estimates of the returns for various utilization technologies. The report concludes that the most economically viable project is the Electricity Generation option, subject to the Parish’s ability and willingness to allocate adequate cash for initial capital and/or to obtain debt financing. However, even this option does not present a solid return: by our estimates, there is a 19 year simple payback on the electricity generation option. All of the energy recovery options discussed in this report

  18. Can we import quality tools? a feasibility study of European practice assessment in a country with less organised general practice

    Directory of Open Access Journals (Sweden)

    Pestiaux Dominique

    2009-10-01

    Full Text Available Abstract Background Quality is on the agenda of European general practice (GP. European researchers have, in collaboration, developed tools to assess quality of GPs. In this feasibility study, we tested the European Practice Assessment (EPA in a one-off project in Belgium, where general practice has a low level of GP organisation. Methods A framework for feasibility analysis included describing the recruiting of participants, a brief telephone study survey among non-responders, organisational and logistic problems. Using field notes and focus groups, we studied the participants' opinions. Results In this study, only 36 of 1000 invited practices agreed to participate. Co-ordination, administrative work, practice visits and organisational problems required several days per practice. The researchers further encountered technical problems, for instance when entering the data and uploading to the web-based server. In subsequent qualitative analysis using two focus groups, most participant GPs expressed a positive feeling after the EPA procedure. In the short period of follow-up, only a few GPs reported improvements after the visit. The participant GPs suggested that follow-up and coaching would probably facilitate the implementation of changes. Conclusion This feasibility study shows that prior interest in EPA is low in the GP community. We encountered a number of logistic and organisational problems. It proved attractive to participants, but it can be augmented by coaching of participants in more than a one-off project to identify and achieve targets for quality improvement. In the absence of commitment of the government, a network of universities and one scientific organisation will offer EPA as a service to training practices.

  19. Minimally invasive videoscopic parathyroidectomy: a feasibility study in dogs and humans.

    Science.gov (United States)

    Norman, J; Albrink, M H

    1997-10-01

    With increasing experience using preoperative sestamibi nuclear scanning, several reports have shown that selective unilateral neck exploration is sufficient in most patients with primary hyperparathyroidism. The current study was undertaken to determine the feasibility of videoscopic parathyroidectomy as a means to decrease scar size while allowing adequate exposure for the identification of normal parathyroid glands and removal of those glands that are enlarged. Eight mongrel dogs underwent removal of all parathyroid glands and both lobes of the thyroid using videoscopic techniques. Once the technical aspects of the operation were established, four patients with primary hyperparathyroidism underwent sestamibi-directed unilateral videoscopic neck exploration with attempted parathyroid removal. All thyroid and parathyroid tissues were removed from each dog without complications. Maintenance of an adequate working space proved to be the major difficulty that necessitated placement of a small mechanical retractor. This problem was even more severe in humans, which prevented the identification of one of four adenomas and three of four normal glands. Although videoscopic surgery is possible within the loose connective tissues of the canine neck, the inability to establish an adequate working space within the neck of humans and the location of parathyroid glands behind the thyroid precludes the use of this technique for patients with hyperparathyroidism.

  20. Quantification of manganese in human hand bones: a feasibility study

    Energy Technology Data Exchange (ETDEWEB)

    Aslam; Pejovic-Milic, A; Chettle, D R; McNeill, F E [Department of Medical Physics and Applied Radiation Sciences, McMaster University, Hamilton, ON, L8S 4K1 (Canada)], E-mail: aslamib@mcmaster.ca

    2008-08-07

    Manganese is both an essential element to human health and also toxic when humans are exposed to excessive levels, particularly by means of inhalation. Biological monitoring of manganese exposure is problematic. It is subject to homeostasis; levels in blood (or serum/plasma) reflect only the most recent exposure and rapidly return to within normal ranges, even when there has been a temporary excursion in response to exposure. In this context, we have been developing a non-invasive technique for measurement of manganese stored in bone, using in vivo neutron activation analysis. Following preliminary feasibility studies, the technique has been enhanced by two significant infrastructure advances. A specially designed irradiation facility serves to maximize the activation of manganese with respect to the dose of ionizing radiation. Secondly, an array of eight NaI(Tl) crystals provides a detection system with very close to 4{pi} geometry. This feasibility study, using neutron activation analysis to measure manganese in the bones of the hand, takes two features into account. Firstly, there is considerable magnesium present in the bone and this produces a spectral interference with the manganese. The {sup 26}Mg(n,{gamma}){sup 27}Mg reaction produces {gamma}-rays of 0.843 MeV from the decay of {sup 27}Mg, which interfere with the 0.847 MeV {gamma}-rays from the decay of {sup 56}Mn, produced by the {sup 55}Mn(n,{gamma}){sup 56}Mn reaction. Secondly, this work provides estimates of the levels of manganese to be expected in referent subjects. A revised estimate has been made from the most recent literature to explore the potential of the technique as a suitable means of screening patients and people exposed to excessive amounts of Mn who could develop many-fold increased levels of Mn in bones as demonstrated through various animal studies. This report presents the enhancements to the neutron activation system, by which manganese can be measured, which resulted in a detection

  1. Quantification of manganese in human hand bones: a feasibility study

    International Nuclear Information System (INIS)

    Aslam; Pejovic-Milic, A; Chettle, D R; McNeill, F E

    2008-01-01

    Manganese is both an essential element to human health and also toxic when humans are exposed to excessive levels, particularly by means of inhalation. Biological monitoring of manganese exposure is problematic. It is subject to homeostasis; levels in blood (or serum/plasma) reflect only the most recent exposure and rapidly return to within normal ranges, even when there has been a temporary excursion in response to exposure. In this context, we have been developing a non-invasive technique for measurement of manganese stored in bone, using in vivo neutron activation analysis. Following preliminary feasibility studies, the technique has been enhanced by two significant infrastructure advances. A specially designed irradiation facility serves to maximize the activation of manganese with respect to the dose of ionizing radiation. Secondly, an array of eight NaI(Tl) crystals provides a detection system with very close to 4π geometry. This feasibility study, using neutron activation analysis to measure manganese in the bones of the hand, takes two features into account. Firstly, there is considerable magnesium present in the bone and this produces a spectral interference with the manganese. The 26 Mg(n,γ) 27 Mg reaction produces γ-rays of 0.843 MeV from the decay of 27 Mg, which interfere with the 0.847 MeV γ-rays from the decay of 56 Mn, produced by the 55 Mn(n,γ) 56 Mn reaction. Secondly, this work provides estimates of the levels of manganese to be expected in referent subjects. A revised estimate has been made from the most recent literature to explore the potential of the technique as a suitable means of screening patients and people exposed to excessive amounts of Mn who could develop many-fold increased levels of Mn in bones as demonstrated through various animal studies. This report presents the enhancements to the neutron activation system, by which manganese can be measured, which resulted in a detection limit in the hand of human subjects of 1.6

  2. Feasibility of deep ocean disposal of heat generating waste. V.1

    International Nuclear Information System (INIS)

    Hemming, C.R.

    1988-06-01

    This report summarises the research performed in the UK during the period 1977 to 1987 as part of the international programme investigating the feasibility of ocean disposal of heat generating radioactive waste. This study has involved: (i) the definition of the disposal operations needed to meet the minimum requirements for safely emplacing waste on or under the floor of the deep ocean; (ii) the identification and characterisation of areas of the deep ocean that might be suitable for containing heat generating waste; (iii) a study of the processes by which radionuclides might migrate through the multiple barriers that isolate the waste from man's environment; and (iv) a calculation of the radiological impact of the conceptual deep ocean repository. It is concluded that, from a technical and scientific viewpoint, disposal of heat generating waste in the deep ocean could provide a safe, economic and feasible alternative to deep disposal on land. (author)

  3. U.S. spent nuclear fuel management: Political, fiscal, and technical feasibility

    International Nuclear Information System (INIS)

    Singer, Clifford

    2013-01-01

    Successful U.S. spent nuclear fuel management policy must satisfy political, fiscal, and technical constraints. Technical requirements have been thoroughly investigated in the United States and Nordic countries for volcanic tuff, salt, and granite. Fiscal planning requires an inflation-adjusted revenue stream and predictable real interest rate earnings on fund balances. A prompt solution satisfying political constraints requires compromise between the overlapping but distinct goals of seven different sets of interests at the federal level. Absent such compromise, there will be delay until sufficient support for one of three strategies evolves: (1) force the Yucca Mountain repository on Nevada, (2) open a centralized storage facility without coupling to repository licensing, or (3) follow a “consent-based” process for repository licensing. Formulations of each of these strategies to overcome impediments to their success are described. - Highlights: • U.S. spent nuclear fuel policy has been at an impasse. • No compromise on Yucca Mountain is at hand. • Yucca only, new repository, or no repository are options. • Success with each is more likely with sounder financing

  4. Front Range Forest Health Partnership Phase 1 feasibility study

    Energy Technology Data Exchange (ETDEWEB)

    Volkin, P

    1998-09-01

    The Front Range Forest Health Partnership is an alliance of individuals, citizen groups, federal, state, private, and nonprofit organizations that formed to promote forest health restoration and reduce fire risks on Colorado's Front Range. The partnership promotes selective thinning to restore forest health and supports economically feasible end uses for wood waste materials. The Phase I study was initiated to determine the environmental and economic feasibility of using wood wastes from forested and urban areas for the production of fuel-grade ethanol.

  5. Noninvasive Prenatal Detection of Trisomy 21 by Targeted Semiconductor Sequencing: A Technical Feasibility Study.

    Science.gov (United States)

    Xi, Yanwei; Arbabi, Aryan; McNaughton, Amy J M; Hamilton, Alison; Hull, Danna; Perras, Helene; Chiu, Tillie; Morrison, Shawna; Goldsmith, Claire; Creede, Emilie; Anger, Gregory J; Honeywell, Christina; Cloutier, Mireille; Macchio, Natasha; Kiss, Courtney; Liu, Xudong; Crocker, Susan; Davies, Gregory A; Brudno, Michael; Armour, Christine M

    2017-01-01

    To develop an alternate noninvasive prenatal testing method for the assessment of trisomy 21 (T21) using a targeted semiconductor sequencing approach. A customized AmpliSeq panel was designed with 1,067 primer pairs targeting specific regions on chromosomes 21, 18, 13, and others. A total of 235 samples, including 30 affected with T21, were sequenced with an Ion Torrent Proton sequencer, and a method was developed for assessing the probability of fetal aneuploidy via derivation of a risk score. Application of the derived risk score yields a bimodal distribution, with the affected samples clustering near 1.0 and the unaffected near 0. For a risk score cutoff of 0.345, above which all would be considered at "high risk," all 30 T21-positive pregnancies were correctly predicted to be affected, and 199 of the 205 non-T21 samples were correctly predicted. The average hands-on time spent on library preparation and sequencing was 19 h in total, and the average number of reads of sequence obtained was 3.75 million per sample. With the described targeted sequencing approach on the semiconductor platform using a custom-designed library and a probabilistic statistical approach, we have demonstrated the feasibility of an alternate method of assessment for fetal T21. © 2017 S. Karger AG, Basel.

  6. Important considerations for feasibility studies in physical activity research involving persons with multiple sclerosis: a scoping systematic review and case study.

    Science.gov (United States)

    Learmonth, Yvonne C; Motl, Robert W

    2018-01-01

    Much research has been undertaken to establish the important benefits of physical activity in persons with multiple sclerosis (MS). There is disagreement regarding the strength of this research, perhaps because the majority of studies on physical activity and its benefits have not undergone initial and systematic feasibility testing. We aim to address the feasibility processes that have been examined within the context of physical activity interventions in MS. A systematic scoping review was conducted based on a literature search of five databases to identify feasibility processes described in preliminary studies of physical activity in MS. We read and extracted methodology from each study based on the following feasibility metrics: process (e.g. recruitment), resource (e.g. monetary costs), management (e.g. personnel time requirements) and scientific outcomes (e.g. clinical/participant reported outcome measures). We illustrate the use of the four feasibility metrics within a randomised controlled trial of a home-based exercise intervention in persons with MS. Twenty-five studies were identified. Resource feasibility (e.g. time and resources) and scientific outcomes feasibility (e.g. clinical outcomes) methodologies were applied and described in many studies; however, these metrics have not been systematically addressed. Metrics related to process feasibility (e.g. recruitment) and management feasibility (e.g. human and data management) are not well described within the literature. Our case study successfully enabled us to address the four feasibility metrics, and we provide new information on management feasibility (i.e. estimate data completeness and estimate data entry) and scientific outcomes feasibility (i.e. determining data collection materials appropriateness). Our review highlights the existing research and provides a case study which assesses important metrics of study feasibility. This review serves as a clarion call for feasibility trials that will

  7. Technical and economic feasibility of thermal energy storage. Annual report

    Energy Technology Data Exchange (ETDEWEB)

    Glenn, D.R.

    1976-02-01

    This study provides a first-look at the system elements involved in: (1) creating a market; (2) understanding and deriving the requirements; (3) performing analytical effort; (4) specifying equipment; and (5) synthesizing applications for a thermal energy storage (TES) function. The work reviews implicated markets, energy consumption patterns, TES technologies, and applications. Further, several concepts are developed and evaluated in some detail. Key findings are: (1) there are numerous technical opportunities for TES in the residential and industrial market sectors; (2) apart from sensible heat storage and transfer, significant R and D is required to fully exploit the superior heat densities of latent heat-based TES systems, particularly at temperatures above 600/sup 0/F; (3) industrial energy conservation can be favorably impacted by TES where periodic or batch-operated unit functions characterize product manufacturing processes, i.e. bricks, steel, and ceramics; and (4) a severe data shortage exists for describing energy consumption rates in real time as related to plant process operations--a needed element in designing TES systems.

  8. Joint Feasibility study on the Instruction of a commercial FBR power plant to Korea between Korea and France

    International Nuclear Information System (INIS)

    Lee, Chang Kun; Cho, Mann; Juhn, Poong Eil; Nam, Jang Soo; Roh, Eun Rae; Yang, Chang Kook; Choi, Young Sang; Shin, Jae In; Chang, Young Nam; Kim, Hoa Gy; Lee, Hong Moon

    1985-03-01

    The objective of this joint feasibility study is to prepare for the implementation plan of the establishment of technological capability prior to the introduction of a commercial FBR power plant to Korea. The scope and contents of the second year project are as follows: Determined are the implementation activities in the two alternative FBR introduction scenarios i.e., a turnkey scenario and a gradual localization scenario with regard to the proportion of domestic participation. And FBR center is modeled as the construction of 4 units of 1,500 MWe LMFBR and related fuel cycle facilities such as reprocessing and fabrication plants at one site. In turnkey scenario, domestic implementation project is selected and the means to develop technical capability are classified into OJT/OJP, R and D, and technology transfer and the floating time schedule is made with reference to the first FBR operation year. In a gradual localization scenario Korean party's plan of means to develop technical capability is prepared. For the analysis of turnkey base introduction scenario project activities were extracted and analyzed referring to IAEA TR. 200 ''Manpower Development for Nuclear power Plant'', Guidebook (1980). And floating time schedule was prepared for the means to develop technical capability and project schedule. For the analysis of gradual localization scenario, project activities were derived under the assumption that entire facilities of FBR center should be localized. PWR's and FBR's fuel reprocessing facilities were incorporated in the reprocessing facility. (Author)

  9. Active Treatment for Idiopathic Adolescent Scoliosis (ACTIvATeS): a feasibility study.

    Science.gov (United States)

    Williams, Mark A; Heine, Peter J; Williamson, Esther M; Toye, Francine; Dritsaki, Melina; Petrou, Stavros; Crossman, Richard; Lall, Ranjit; Barker, Karen L; Fairbank, Jeremy; Harding, Ian; Gardner, Adrian; Slowther, Anne-Marie; Coulson, Neil; Lamb, Sarah E

    2015-07-01

    The feasibility of conducting a definitive randomised controlled trial (RCT) evaluating the clinical effectiveness and cost-effectiveness of scoliosis-specific exercises (SSEs) for adolescent idiopathic scoliosis (AIS) is uncertain. The aim of this study was to assess the feasibility of conducting a large, multicentre trial of SSE treatment for patients with AIS, in comparison with standard care, and to refine elements of the study design. The objectives were to (1) update a systematic review of controlled trials evaluating the efficacy of SSE in AIS; (2) survey UK orthopaedic surgeons and physiotherapists to determine current practice, patient populations and equipoise; (3) randomise 50 adolescents to a feasibility trial of either usual care or SSE interventions across a range of sites; (4) develop, document and assess acceptability and adherence of interventions; (5) assess and describe training requirements of physiotherapists; and (6) gain user input in all relevant stages of treatment and protocol design. Multicomponent feasibility study including UK clinician survey, systematic literature review and a randomised feasibility trial. The randomised feasibility study involved four secondary care NHS trusts providing specialist care for patients with AIS. The randomised feasibility study recruited people aged 10-16 years with mild AIS (Cobb angle of physiotherapy SSE programme supported by a home exercise plan. Our choice of intervention was informed by a systematic review of exercise interventions for AIS. The main outcome was feasibility of recruitment to the randomised study. Other elements were to inform choice of outcomes for a definitive trial and included curve severity, quality of life, requirement for surgery/brace, adverse events, psychological symptoms, costs and health utilities. A UK survey of orthopaedic consultants and physiotherapists indicated a wide variation in current provision of exercise therapy through physiotherapy services. It also found

  10. Analyzing maintenance strategies by agent-based simulations: A feasibility study

    International Nuclear Information System (INIS)

    Kaegi, M.; Mock, R.; Kroeger, W.

    2009-01-01

    Thoroughly planned and implemented maintenance strategies save time and cost. However, the integration of maintenance work into reliability analysis is difficult as common modeling techniques are often not applicable due to state explosion which calls for restrictive model assumptions and oversimplification. From authors' point of view, agent-based modeling (ABM) of technical and organizational systems is a promising approach to overcome such problems. But since ABM is not well established in reliability analysis its feasibility in this area still has to be demonstrated. For this purpose ABM is compared with Markov chains, namely by analyzing the reliability of a maintained n-unit system with dependent repair events, applying both modeling approaches. Although ABM and Markov chains lead to the same numerical results, the former points out the potentiality of an improved system state handling. This is demonstrated by extending the ABM with operators as additional 'agents' featuring their location (x;y) availability (0;1) and different maintenance strategies. This extension highlights the capability of ABM to analyze complex emergent system behavior and allows a systematic refinement and optimization of the maintenance strategies.

  11. Conceptual Design and Feasibility Analyses of a Robotic System for Automated Exterior Wall Painting

    Directory of Open Access Journals (Sweden)

    Young S. Kim

    2008-11-01

    Full Text Available There are approximately 6,677,000 apartment housing units in South Korea. Exterior wall painting for such multi-dwelling apartment housings in South Korea represents a typical area to which construction automation technology can be applied for improvement in safety, productivity, quality, and cost over the conventional method. The conventional exterior wall painting is costly and labor-intensive, and it especially exposes workers to significant health and safety risks. The primary objective of this study is to design a conceptual model of an exterior wall painting robot which is applicable to apartment housing construction and maintenance, and to conduct its technical?economical feasibility analyses. In this study, a design concept using a high ladder truck is proposed as the best alternative for automation of the exterior wall painting. Conclusions made in this study show that the proposed exterior wall painting robot is technically and economically feasible, and can greatly enhance safety, productivity, and quality compared to the conventional method. Finally, it is expected that the conceptual model of the exterior wall painting robot would be efficiently used in various applications in exterior wall finishing and maintenance of other architectural and civil structures such as commercial buildings, towers, and high-rise storage tanks.

  12. Technical approach to finalizing sensible soil cleanup levels at the Fernald Environmental Management Project

    International Nuclear Information System (INIS)

    Carr, D.; Hertel, B.; Jewett, M.; Janke, R.; Conner, B.

    1996-01-01

    The remedial strategy for addressing contaminated environmental media was recently finalized for the US Department of Energy's (DOE) Fernald Environmental Management Project (FEMP) following almost 10 years of detailed technical analysis. The FEMP represents one of the first major nuclear facilities to successfully complete the Remedial Investigation/Feasibility Study (RI/FS) phase of the environmental restoration process. A critical element of this success was the establishment of sensible cleanup levels for contaminated soil and groundwater both on and off the FEMP property. These cleanup levels were derived based upon a strict application of Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA) regulations and guidance, coupled with positive input from the regulatory agencies and the local community regarding projected future land uses for the site. The approach for establishing the cleanup levels was based upon a Feasibility Study (FS) strategy that examined a bounding range of viable future land uses for the site. Within each land use, the cost and technical implications of a range of health-protective cleanup levels for the environmental media were analyzed. Technical considerations in driving these cleanup levels included: direct exposure routes to viable human receptors; cross- media impacts to air, surface water, and groundwater; technical practicality of attaining the levels; volume of affected media; impact to sensitive environmental receptors or ecosystems; and cost. This paper will discuss the technical approach used to support the finalization of the cleanup levels for the site. The final cleanup levels provide the last remaining significant piece to the puzzle of establishing a final site-wide remedial strategy for the FEMP, and positions the facility for the expedient completion of site-wide remedial activities

  13. Bond Feasibility Study. Project Identification Committee Report.

    Science.gov (United States)

    Wichita Public Schools, KS.

    A committee, appointed by the Board of Education, was requested to make a comprehensive study of the school building needs of Unified School District No. 259. In an attempt to determine the feasibility of a general bond election to upgrade the public schools, the specific charge to the committee was to evaluate the needs for physical plant…

  14. The Feasibility of Teaching Science via a Socio-Historical Approach. Part 1. Technical Report No. 303.

    Science.gov (United States)

    Agin, Michael Lawrence

    Reported is a study made to determine the feasibility of teaching science by utilizing selected concepts related to the social and historical development of science and selected concepts related to atomic energy. Instructional materials included textual materials developed by the investigator, a test, a series of slides, and four motion pictures.…

  15. Ear-EEG from generic earpieces: A feasibility study

    DEFF Research Database (Denmark)

    Kidmose, Preben; Looney, D; Jochumsen, Lars

    2013-01-01

    key patient needs (discreet, unobstrusive, user-friendly, robust) and that is low-cost and suitable for off-the-shelf use; thus promising great advantages for healthcare applications. Its feasibility is validated in a comprehensive comparative study with our established prototype, based...

  16. Modelling the International Climate Change Negotiations: A Non-Technical Outline of Model Architecture

    Energy Technology Data Exchange (ETDEWEB)

    Underdal, Arild

    1997-12-31

    This report discusses in non-technical terms the overall architecture of a model that will be designed to enable the user to (1) explore systematically the political feasibility of alternative policy options and (2) to determine the set of politically feasible solutions in the global climate change negotiations. 25 refs., 2 figs., 1 tab.

  17. Fast-mixed spectrum reactor interim report initial feasibility study

    International Nuclear Information System (INIS)

    Fischer, G.J.; Cerbone, R.J.

    1979-01-01

    The report summarizes the results of an initial four-month feasibility study of the Fast-Mixed Spectrum Reactor (FMSR). Reactor physics, fuel cycle, and thermal-hydraulic analyses were performed on a reference design. These results when coupled to a fuel and materials evaluation performed in cooperation with the Argonne National Laboratory indicate that the FMSR is feasible provided the fuels, cladding, and subassembly ducts can survive a peak fuel burnup of 15 to 20 atom percent heavy metal and peak fluences of 8 x 10 23 (nvt > 0.1 MeV). The results of this short study have also provided a basis for exploring alternative designs requiring significantly lower peak burnup and fluences for their operation

  18. Longitudinal study of the feasibility of using ecological momentary assessment to study teacher stress: Objective and self-reported measures.

    Science.gov (United States)

    McIntyre, Teresa M; McIntyre, Scott E; Barr, Christopher D; Woodward, Phillip S; Francis, David J; Durand, Angelia C; Mehta, Paras; Kamarck, Thomas W

    2016-10-01

    There is a lack of comprehensive research on Ecological Momentary Assessment (EMA) feasibility to study occupational stress, especially its long-term sustainability. EMA application in education contexts has also been sparse. This study investigated the feasibility of using EMA to study teacher stress over 2 years using both objective compliance data and a self-reported feasibility survey. It also examined the influence of individual and school factors on EMA feasibility. Participants were 202 sixth through eighth grade teachers from 22 urban middle schools in the southern United States. EMA was implemented via an iPod-based Teacher Stress Diary (TSD). Teachers recorded demands, stress responses, and resources during 12 days (6 waves) over 2 years. Feasibility was assessed via compliance data generated by the TSD (e.g., entry completion) and an EMA Feasibility Survey of self-reported user-friendliness and EMA interference. The results showed high compliance regarding entry and item completion, and completion time, which was sustained over time. User-friendliness was appraised as very high and EMA interference as low. Initial difficulties regarding timing and length of assessments were addressed via EMA method refinement, resulting in improved feasibility. Teachers' ethnicity, age, marital status, grade/course taught, class size, class load, and daily workload impacted feasibility. The results supported the feasibility of using EMA to study work stress longitudinally and the value of continued feasibility monitoring. They also support EMA use to study teacher stress and inform EMA implementation in schools. Some teacher and school factors need to be taken into consideration when deciding on EMA implementation in education contexts. (PsycINFO Database Record (c) 2016 APA, all rights reserved).

  19. Congeneration feasibility: Otis Elavator Company and Polychrome Corporation

    Science.gov (United States)

    Fox, H.

    1982-05-01

    An investigation of the technical and economic feasibility of cogenerating electric and thermal power at two manufacturing plants (Otis Elevator Company and Polychrome Corporation) located on neighboring properties in Yonkers, NY is discussed. Existing electrical and steam producing equipment and energy consumption date are summarized. Alternative cases examined include electrical energy generation, electrical energy generation with waste heat recovery and a combined cycle case. Also reported are life cycle cost economic evaluations including simple payback period and return on investment indices. While it was concluded that cogeneration of heat and electricity at these industrial plant sites would not be economically viable, this detailed study provides valuable insights.

  20. International Case-Control Study of Adult Brain, Head and Neck Tumours: Results of the Feasibility Study (invited paper)

    International Nuclear Information System (INIS)

    Cardis, E.; Kilkenny, M.

    1999-01-01

    The objectives of the feasibility study were to collect and analyse the information necessary to assess the feasibility of a multi-centric study of adult head and neck tumours (including brain tumours) and mobile telephones. Information was obtained on the availability and accessibility of records from companies, the prevalence of mobile telephone use over time and the expected number of tumour cases in the proposed study regions. The conclusion is that it is feasible to develop a study of the relation between mobile telephone use and brain cancer risk. The feasibility of a study of the relation between radiofrequency exposure and cancer risk is, however, unclear at present. It is unknown whether a sufficiently accurate and precise RF exposure gradient can be derived to classify adequately each subject in the proposed study. A study of the relation between mobile telephone use and risk of salivary gland tumours and acoustic neurinomas is probably feasible, but more information is required about the logistic difficulties of ascertaining these cases in the study regions. Two subcommittees have been formed to develop the exposure measurement and epidemiological aspect of the study. (author)

  1. DPC loading feasibility study report

    International Nuclear Information System (INIS)

    Dafoe, R.E.; Lopez, D.A.; Williams, K.L.

    1997-11-01

    Disposal of radioactive wastes now stored at the Idaho Chemical Processing Plant at the Idaho National Engineering and Environmental Laboratory is mandated under a ''Settlement Agreement'' between the Department of Energy and the State of Idaho. This study investigates the feasibility of using the Dry Transfer Cell facility to package waste into Dual Purpose Canisters for interim storage at the adjacent Dry Storage System comprised of an interim storage pad with NUHOMS reg-sign storage modules. The wastes would then be road-ready for eventual disposal in a permanent repository. The operating period for these activities is expected to be from 2015 to 2035

  2. Training Endogenous Task Shifting Using Music Therapy: A Feasibility Study.

    Science.gov (United States)

    Lynch, Colleen; LaGasse, A Blythe

    2016-01-01

    People with acquired brain injury (ABI) are highly susceptible to disturbances in executive functioning (EF), and these effects are pervasive. Research studies using music therapy for cognitive improvement in this population are limited. The purpose of this study was to determine the feasibility of a Musical Executive Function Training (MEFT) intervention to address task-shifting skills in adults with ABI and to obtain preliminary evidence of intervention effect on task shifting. Fourteen participants were randomly assigned to one of three groups: a music therapy intervention group (MTG), a singing group (SG), or the no-intervention control group (CG). The SG and MTG met for one hour a day for five days. Feasibility measures included participant completion rates and intervention fidelity. Potential benefits were measured using the Trail Making Test and the Paced Auditory Serial Addition Task as a pre- and posttest measure. Participant completion rates and interventionist fidelity to the protocol supported feasibility. One-way ANOVA of the pre- and posttest group differences revealed a trend toward improvement in the MTG over the SG. Feasibility and effect size data support a larger trial of the MEFT protocol. © the American Music Therapy Association 2016. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

  3. The use of consumer depth cameras for 3D surface imaging of people with obesity: A feasibility study.

    Science.gov (United States)

    Wheat, J S; Clarkson, S; Flint, S W; Simpson, C; Broom, D R

    2018-05-21

    Three dimensional (3D) surface imaging is a viable alternative to traditional body morphology measures, but the feasibility of using this technique with people with obesity has not been fully established. Therefore, the aim of this study was to investigate the validity, repeatability and acceptability of a consumer depth camera 3D surface imaging system in imaging people with obesity. The concurrent validity of the depth camera based system was investigated by comparing measures of mid-trunk volume to a gold-standard. The repeatability and acceptability of the depth camera system was assessed in people with obesity at a clinic. There was evidence of a fixed systematic difference between the depth camera system and the gold standard but excellent correlation between volume estimates (r 2 =0.997), with little evidence of proportional bias. The depth camera system was highly repeatable - low typical error (0.192L), high intraclass correlation coefficient (>0.999) and low technical error of measurement (0.64%). Depth camera based 3D surface imaging was also acceptable to people with obesity. It is feasible (valid, repeatable and acceptable) to use a low cost, flexible 3D surface imaging system to monitor the body size and shape of people with obesity in a clinical setting. Copyright © 2018 Asia Oceania Association for the Study of Obesity. Published by Elsevier Ltd. All rights reserved.

  4. The feasibility study on commercialized fast reactor cycle system

    International Nuclear Information System (INIS)

    Noda, Hiroshi

    2002-01-01

    The feasibility study on commercialized Fast Reactor cycle system (FS) has been carried out by a joint team with the participation of all parties concerned in Japan since July, 1999. It aims to clarify various perspectives for commercialized fast reactor cycle system and also suggest development strategies to diverse social needs in the 21 st century. The FS consists of several phases. The phase 1 has progressed as planned and the highly feasible candidate concepts with innovative technologies have been screened out among a wide variety of concepts. During the phase 2, approximately five years after the phase 1, the in-depth design studies and engineering scale tests of key technologies are being conducted to verify and validate the feasibility of screened candidate concepts. At the end of the phase 2, a few promising concepts will be selected with their R and D tasks. The paper describes the results of the phase 1, the activities of the phase 2 and the new concept related to the fast reactor fuel cycle focusing on the reduction in environmental burden, which is one of key factors to sustain the nuclear power generation in the 21 st century

  5. A Persuasive and Social mHealth Application for Physical Activity: A Usability and Feasibility Study.

    Science.gov (United States)

    Al Ayubi, Soleh U; Parmanto, Bambang; Branch, Robert; Ding, Dan

    2014-05-22

    Advances in smartphones and the wide usage of social networking systems offer opportunities for the development of innovative interventions to promote physical activity. To that end, we developed a persuasive and social mHealth application designed to monitor and motivate users to walk more every day. The objectives of this project were to conduct a focused review on the fundamental characteristics of mHealth for physical activity promotion, to develop an mHealth application that meets such characteristics, and to conduct a feasibility study to deploy the application in everyday life. This project started as an analytical study to review the fundamental characteristics of the technologies used in physical activity monitoring and promotion. Then, it was followed by a technical development of the application. Next, a 4 week deployment was conducted where participants used the application as part of their daily life. A think-aloud method and in-depth semistructured interviews were conducted following the deployment. A qualitative description method was used to thematically analyze the interviews. Feasibility measures included, adherence to the program, user-system interactions, motivation to use, and experience with physical activity and online social interactions. There were seven fundamental characteristics of physical activity monitoring and promotion that were identified, which were then used as a foundation to develop the application. There were fourteen participants that enrolled in the application evaluation. The age range was from 24 to 45; body mass index ranged from 18.5 to 42.98, with 4 of the subjects falling into the category "obese". Half of them were experienced with smartphones, and all were familiar with a social network system. There were thirteen participants that completed the study; one was excluded. Overall, participants gave high scores to almost all of the usability factors examined, with averages of 4.52 out of a 5.00 maximum. Over 29 days

  6. Feasibility study for the installation of a nuclear reactor in thermal stimulation processes in heavy oil extraction from Orinoco oil belt

    International Nuclear Information System (INIS)

    Munoz, A.; Sanchez, R.

    1982-01-01

    Due to strategic need in the exploitation of heavy and extraheavy oil wells of Orinoco oil belt, technical and economical studies have been carried out to determine an optimal method for oil production and exploitation. So far, studies indicate thermal stimulation is the most adequate technique. Experience shows that stimulation cost is high when traditional methods (boilers) are used. The profit is due to the high price of oil in international market. Due to actual oil price trends, evaluation of nontraditional methods to generate steam in thermal stimulation processes (steam injection) is in order. A nuclear reactor as steam generator was evaluated. It was found economical feasibility and saving in fuel cost between 31.08% and 72.63% depending on oil prices

  7. Technical democracy as a challenge to urban studies

    DEFF Research Database (Denmark)

    Farías, Ignacio; Blok, Anders

    2016-01-01

    What is technical democracy? And why does it matter for urban studies? As an introduction to this special feature, we address these questions by reflecting on To Our Friends, the 2014 manifesto of the Invisible Committee. We engage in particular its provocative diagnosis of the current situation......: power no longer resides in the modern institutions of representative democracy and the market economy; instead, power has become a matter of logistics, infrastructures and expertise. This diagnosis, we suggest, brings into view the challenge of technical democracy, that is, the democratization of techno......-scientific expertise and the instauration of forms of lasting collaboration among experts and laypeople. Urban politics, we claim, increasingly turns around socio-technical controversies and it is in terms of the politics of expertise that we should analyse and engage it. Building on Science and Technology Studies...

  8. Subsidence monitoring system for offshore applications: technology scouting and feasibility studies

    Directory of Open Access Journals (Sweden)

    R. Miandro

    2015-11-01

    Full Text Available Because of concern about possible impacts of hydrocarbon production activities on coastal-area environments and infrastructures, new hydrocarbon offshore development projects in Italy must submit a monitoring plan to Italian authorities to measure and analyse real-time subsidence evolution. The general geological context, where the main offshore Adriatic fields are located, is represented by young unconsolidated terrigenous sediments. In such geological environments, sea floor subsidence, caused by hydrocarbon extraction, is quite probable. Though many tools are available for subsidence monitoring onshore, few are available for offshore monitoring. To fill the gap ENI (Ente Nazionale Idrocarburi started a research program, principally in collaboration with three companies, to generate a monitoring system tool to measure seafloor subsidence. The tool, according to ENI design technical-specification, would be a robust long pipeline or cable, with a variable or constant outside diameter (less than or equal to 100 mm and interval spaced measuring points. The design specifications for the first prototype were: to detect 1 mm altitude variation, to work up to 100 m water depth and investigation length of 3 km. Advanced feasibility studies have been carried out with: Fugro Geoservices B.V. (Netherlands, D'Appolonia (Italy, Agisco (Italy. Five design (using three fundamental measurements concepts and five measurement tools were explored: cable shape changes measured by cable strain using fiber optics (Fugro; cable inclination measured using tiltmeters (D'Appolonia and measured using fiber optics (Fugro; and internal cable altitude-dependent pressure changes measured using fiber optics (Fugro and measured using pressure transducers at discrete intervals along the hydraulic system (Agisco. Each design tool was analysed and a rank ordering of preferences was performed. The third method (measurement of pressure changes, with the solution proposed by Agisco

  9. Subsidence monitoring system for offshore applications: technology scouting and feasibility studies

    Science.gov (United States)

    Miandro, R.; Dacome, C.; Mosconi, A.; Roncari, G.

    2015-11-01

    Because of concern about possible impacts of hydrocarbon production activities on coastal-area environments and infrastructures, new hydrocarbon offshore development projects in Italy must submit a monitoring plan to Italian authorities to measure and analyse real-time subsidence evolution. The general geological context, where the main offshore Adriatic fields are located, is represented by young unconsolidated terrigenous sediments. In such geological environments, sea floor subsidence, caused by hydrocarbon extraction, is quite probable. Though many tools are available for subsidence monitoring onshore, few are available for offshore monitoring. To fill the gap ENI (Ente Nazionale Idrocarburi) started a research program, principally in collaboration with three companies, to generate a monitoring system tool to measure seafloor subsidence. The tool, according to ENI design technical-specification, would be a robust long pipeline or cable, with a variable or constant outside diameter (less than or equal to 100 mm) and interval spaced measuring points. The design specifications for the first prototype were: to detect 1 mm altitude variation, to work up to 100 m water depth and investigation length of 3 km. Advanced feasibility studies have been carried out with: Fugro Geoservices B.V. (Netherlands), D'Appolonia (Italy), Agisco (Italy). Five design (using three fundamental measurements concepts and five measurement tools) were explored: cable shape changes measured by cable strain using fiber optics (Fugro); cable inclination measured using tiltmeters (D'Appolonia) and measured using fiber optics (Fugro); and internal cable altitude-dependent pressure changes measured using fiber optics (Fugro) and measured using pressure transducers at discrete intervals along the hydraulic system (Agisco). Each design tool was analysed and a rank ordering of preferences was performed. The third method (measurement of pressure changes), with the solution proposed by Agisco, was

  10. Technical document characterization by data analysis

    International Nuclear Information System (INIS)

    Mauget, A.

    1993-05-01

    Nuclear power plants possess documents analyzing all the plant systems, which represents a vast quantity of paper. Analysis of textual data can enable a document to be classified by grouping the texts containing the same words. These methods are used on system manuals for feasibility studies. The system manual is then analyzed by LEXTER and the terms it has selected are examined. We first classify according to style (sentences containing general words, technical sentences, etc.), and then according to terms. However, it will not be possible to continue in this fashion for the 100 system manuals existing, because of lack of sufficient storage capacity. Another solution is being developed. (author)

  11. Feasibility of geothermal space/water heating for Mammoth Lakes Village, California. Final report, September 1976--September 1977

    Energy Technology Data Exchange (ETDEWEB)

    Sims, A.V.; Racine, W.C.

    1977-12-01

    Results of a study to determine the technical, economic, and environmental feasibility of geothermal district heating for Mammoth Lakes Village, California are reported. The geothermal district heating system selected is technically feasible and will use existing technology in its design and operation. District heating can provide space and water heating energy for typical customers at lower cost than alternative sources of energy. If the district heating system is investor owned, lower costs are realized after five to six years of operation, and if owned by a nonprofit organization, after zero to three years. District heating offers lower costs than alternatives much sooner in time if co-generation and/or DOE participation in system construction are included in the analysis. During a preliminary environmental assessment, no potential adverse environmental impacts could be identified of sufficient consequence to preclude the construction and operation of the proposed district heating system. A follow-on program aimed at implementing district heating in Mammoth is outlined.

  12. A feasibility study of thyroid cancer among patients treated with I-131

    International Nuclear Information System (INIS)

    Anderson, T.W.

    1984-04-01

    This study examined the feasibility of conducting a Canada-wide follow-up study of persons receiving I-131 before 1970, to see if current estimates of induction of thyroid cancer are well founded. It is concluded that such a study is not feasible due to the widespread destruction of old records, and the limited quantity of personal identifying information on those records that do still exist

  13. The Dutch Technical-Tactical Tennis Test (D4T) for Talent Identification and Development : Psychometric Characteristics

    NARCIS (Netherlands)

    Kolman, Nikki; Huijgen, Barbara; Kramer, Tamara; Elferink-Gemser, Marije; Visscher, Chris

    2017-01-01

    This study examined the test-retest reliability, validity and feasibility of the newly developed Dutch Technical Tactical Tennis Test (D4T). This new test is relevant for talent identification and development in tennis. Thirty-two youth male tennis players (age 13.4 +/- 0.5) were classified as elite

  14. 200-BP-5 operable unit Technical Baseline report

    International Nuclear Information System (INIS)

    Jacques, I.D.; Kent, S.K.

    1991-10-01

    This report supports development of a remedial investigation/feasibility study work plan for the 200-BP-5 operable unit. The report summarizes baseline information for waste sites and unplanned release sites located in the 200-BP-5 operable unit. The sites were investigated by the Technical Baseline Section of the Environmental Engineering Group, Westinghouse Hanford Company (Westinghouse Hanford). The investigation consisted of review and evaluation of current and historical Hanford Site reports, drawings, and photographs, and was supplemented with recent inspections of the Hanford Site and employee interviews. No field investigations or sampling were conducted

  15. Presurgical motor, somatosensory and language fMRI: Technical feasibility and limitations in 491 patients over 13 years

    International Nuclear Information System (INIS)

    Tyndall, Anthony J.; Reinhardt, Julia; Stippich, Christoph; Tronnier, Volker; Mariani, Luigi

    2017-01-01

    To analyse the long-term feasibility and limitations of presurgical fMRI in a cohort of tumour and epilepsy patients with different MR-scanners at 1.5 and 3.0 T. Four hundred and ninety-one consecutive patients undergoing presurgical fMRI between 2000 and 2012 on five different MR-scanners using established paradigms and semi-automated data processing were included. Success rates of task performance and BOLD-activation were determined for motor and somatosensory somatotopic mapping and language localisation. Procedural success, failures and imaging artifacts were analysed. MR-field strengths were compared. Two thousand three hundred fifteen of 2348 (98.6 %) attempted paradigms (1033 motor, 1220 speech, 95 somatosensory) were successfully performed. 100 paradigms (4.3 %) were repetition runs. 23 speech, 6 motor and 2 sensory paradigms failed for non-compliance and technical issues. Most language paradigm failures were noted in overt sentence generation. Average significant BOLD-activation was higher for motor than language paradigms (95.8 vs. 81.6 %). Most language paradigms showed significantly higher activation rates at 3 T compared to 1.5 T, whereas no significant difference was found for motor paradigms. fMRI proved very robust for the presurgical localisation of the different motor and somatosensory body representations, as well as Broca's and Wernicke's language areas across different MR-scanners at 1.5 and 3.0 T over 13 years. (orig.)

  16. Presurgical motor, somatosensory and language fMRI: Technical feasibility and limitations in 491 patients over 13 years

    Energy Technology Data Exchange (ETDEWEB)

    Tyndall, Anthony J.; Reinhardt, Julia; Stippich, Christoph [University Hospital Basel, Division of Diagnostic and Interventional Neuroradiology, Basel (Switzerland); Tronnier, Volker [University Hospital Schleswig-Holstein, Luebeck Campus, Department of Neurosurgery, Luebeck (Germany); Mariani, Luigi [University Hospitals Basel, Department of Neurosurgery, Basel (Switzerland)

    2017-01-15

    To analyse the long-term feasibility and limitations of presurgical fMRI in a cohort of tumour and epilepsy patients with different MR-scanners at 1.5 and 3.0 T. Four hundred and ninety-one consecutive patients undergoing presurgical fMRI between 2000 and 2012 on five different MR-scanners using established paradigms and semi-automated data processing were included. Success rates of task performance and BOLD-activation were determined for motor and somatosensory somatotopic mapping and language localisation. Procedural success, failures and imaging artifacts were analysed. MR-field strengths were compared. Two thousand three hundred fifteen of 2348 (98.6 %) attempted paradigms (1033 motor, 1220 speech, 95 somatosensory) were successfully performed. 100 paradigms (4.3 %) were repetition runs. 23 speech, 6 motor and 2 sensory paradigms failed for non-compliance and technical issues. Most language paradigm failures were noted in overt sentence generation. Average significant BOLD-activation was higher for motor than language paradigms (95.8 vs. 81.6 %). Most language paradigms showed significantly higher activation rates at 3 T compared to 1.5 T, whereas no significant difference was found for motor paradigms. fMRI proved very robust for the presurgical localisation of the different motor and somatosensory body representations, as well as Broca's and Wernicke's language areas across different MR-scanners at 1.5 and 3.0 T over 13 years. (orig.)

  17. Investigating the potential and feasibility of an offshore wind farm in the Northern Adriatic Sea

    International Nuclear Information System (INIS)

    Schweizer, Joerg; Antonini, Alessandro; Govoni, Laura; Gottardi, Guido; Archetti, Renata; Supino, Enrico; Berretta, Claudia; Casadei, Carlo; Ozzi, Claudia

    2016-01-01

    Highlights: • First feasibility study for an offshore wind farm in the Northern Adriatic Sea. • Field wind and wave data collected at the site. • Site-specific design of transition piece and foundation. • Economical and technical feasibility applied to four different scenarios. - Abstract: The use of offshore wind power is becoming increasingly important towards a sustainable growth worldwide. In Italy, as well as in other countries where wind energy is provided only by onshore plants, the interest in the deployment of offshore wind resources is rapidly growing, despite relatively modest average wind speeds, compared to typical wind conditions in the North Sea. Research efforts have, so far, addressed the exploration of the most promising locations, based on wind characteristics; however, more extended evidence of technical and economic feasibility is now needed to raise awareness in the decision makers and secure to this source of renewable energy a proper role in the future energy policies. Within such a context, the paper presents the first feasibility study for the development of an offshore wind farm off the coast of Rimini, in the Northern Adriatic Sea. The study is based on an anemometric campaign started at the site in 2008 to provide a statistical assessment of the wind characteristics and the related wind energy potential, and on a 10-year wave measurement record next to the area, together with a thorough analysis of the site geological and environmental characteristics. Environmental data are interpreted with a proper consideration of the extreme events distribution and relevant results are used to select the most appropriate commercially available wind turbine and to design the site-specific support structure. A comprehensive evaluation of the investment costs and revenues is then carried out with reference to two wind farm layouts (a first smaller, constituted of 15 elements, and another one, featuring up to 60 elements) and in relation to two

  18. Engineering feasibility analysis for in-situ stabilization of Canonsburg residues. [UMTRA project

    Energy Technology Data Exchange (ETDEWEB)

    1982-01-01

    The US Department of Energy is considering several methods for carrying out remedial actions in Canonsburg, Pennsylvania, at the site of an inactive uranium-processing mill. The main objective of this study is to determine the feasibility of in-situ stabilization as the remedial action. In-situ stabilization is an alternative to site decontamination and offsite disposal. The problems associated with offsite hauling of large quantities of contaminated material and with the location and development of a new disposal site could be avoided by the implementation of an in-situ stabilization concept. In addition, the in-situ approach would be more cost-effective than offsite disposal. This study will establish that a technically feasible and implementable in-situ stabilization concept can be developed that meets regulatory requirements and is cost effective. This study in no way commits the DOE to implement any specific actions described herein. 11 refs., 30 figs., 24 tabs.

  19. Deschutes estuary feasibility study: hydrodynamics and sediment transport modeling

    Science.gov (United States)

    George, Douglas A.; Gelfenbaum, Guy; Lesser, Giles; Stevens, Andrew W.

    2006-01-01

    Continual sediment accumulation in Capitol Lake since the damming of the Deschutes River in 1951 has altered the initial morphology of the basin. As part of the Deschutes River Estuary Feasibility Study (DEFS), the United States Geological Survey (USGS) was tasked to model how tidal and storm processes will influence the river, lake and lower Budd Inlet should estuary restoration occur. Understanding these mechanisms will assist in developing a scientifically sound assessment on the feasibility of restoring the estuary. The goals of the DEFS are as follows. - Increase understanding of the estuary alternative to the same level as managing the lake environment.

  20. Feasibility analysis of wastewater and solid waste systems for application in Indonesia

    NARCIS (Netherlands)

    Kerstens, S.M.; Leusbrock, I.; Zeeman, G.

    2015-01-01

    Indonesia is one of many developing countries with a backlog in achieving targets for the implementation of wastewater and solid waste collection, treatment and recovery systems. Therefore a technical and financial feasibility analysis of these systems was performed using Indonesia as an example.

  1. Percutaneous sacroplasty with the use of C-arm flat-panel detector CT: technical feasibility and clinical outcome

    International Nuclear Information System (INIS)

    Kang, Sung Eun; Lee, Joon Woo; Kim, Joo Hyung; Kang, Heung Sik; Park, Kun Woo; Yeom, Jin S.

    2011-01-01

    Sacroplasty for sacral insufficiency fractures (SIFs) has been performed mostly under computed tomography (CT) or fluoroscopy guidance. The purposes of this study are to describe technical tips and clinical outcomes of sacroplasty under C-arm flat panel detector CT (C-arm CT) guidance, and to compare the cement distributions shown on C-arm CT with those on multi-detector CT (MDCT). This study consisted of patients who underwent sacroplasty for SIF using C-arm CT from May 2006 to May 2009. Technical success was assessed in terms of cement filling and leakage. Clinical outcome was assessed at short-term (less than 1 month) and long-term (more than 1 month) follow-up using a four-grade patient satisfaction scale: poor, fair, good, and excellent. After sacroplasty, all patients underwent MDCT and three radiologists compared MDCT images with C-arm CT images in consensus, focusing on the cement distribution and cement leakage. Sacroplasties were performed on both sacral alae in all 8 patients (male:female = 2:6, mean age = 76.9, range = 63-82). The technical success rate was 100%. At short-term follow up, 6 patients (87.5%) reported significant improvement. Five patients (62.5%) were available for long-term follow-up and all 5 patients reported a reduced pain and an improved ability to ambulate. Using MDCT as the standard of reference, the cement distribution was visualized equally well by C-arm CT. Sacroplasty under C-arm CT showed excellent technical success and good clinical outcome. There was an excellent correlation between C-arm CT and MDCT in evaluating cement distribution and cement leakage. (orig.)

  2. Percutaneous sacroplasty with the use of C-arm flat-panel detector CT: technical feasibility and clinical outcome

    Energy Technology Data Exchange (ETDEWEB)

    Kang, Sung Eun; Lee, Joon Woo; Kim, Joo Hyung; Kang, Heung Sik [Seoul National University Bundang Hospital, Department of Radiology, Gyeonggi-do (Korea, Republic of); Park, Kun Woo; Yeom, Jin S. [Seoul National University Bundang Hospital, Department of Orthopaedic Surgery, Gyeonggi-do (Korea, Republic of)

    2011-04-15

    Sacroplasty for sacral insufficiency fractures (SIFs) has been performed mostly under computed tomography (CT) or fluoroscopy guidance. The purposes of this study are to describe technical tips and clinical outcomes of sacroplasty under C-arm flat panel detector CT (C-arm CT) guidance, and to compare the cement distributions shown on C-arm CT with those on multi-detector CT (MDCT). This study consisted of patients who underwent sacroplasty for SIF using C-arm CT from May 2006 to May 2009. Technical success was assessed in terms of cement filling and leakage. Clinical outcome was assessed at short-term (less than 1 month) and long-term (more than 1 month) follow-up using a four-grade patient satisfaction scale: poor, fair, good, and excellent. After sacroplasty, all patients underwent MDCT and three radiologists compared MDCT images with C-arm CT images in consensus, focusing on the cement distribution and cement leakage. Sacroplasties were performed on both sacral alae in all 8 patients (male:female = 2:6, mean age = 76.9, range = 63-82). The technical success rate was 100%. At short-term follow up, 6 patients (87.5%) reported significant improvement. Five patients (62.5%) were available for long-term follow-up and all 5 patients reported a reduced pain and an improved ability to ambulate. Using MDCT as the standard of reference, the cement distribution was visualized equally well by C-arm CT. Sacroplasty under C-arm CT showed excellent technical success and good clinical outcome. There was an excellent correlation between C-arm CT and MDCT in evaluating cement distribution and cement leakage. (orig.)

  3. Feasibility study of component risk ranking for plant maintenance

    International Nuclear Information System (INIS)

    Ushijima, Koji; Yonebayashi, Kenji; Narumiya, Yoshiyuki; Sakata, Kaoru; Kumano, Tetsuji

    1999-01-01

    Nuclear power is the base load electricity source in Japan, and reduction of operation and maintenance cost maintaining or improving plant safety is one of the major issues. Recently, Risk Informed Management (RIM) is focused as a solution. In this paper, the outline regarding feasibility study of component risk ranking for plant maintenance for a typical Japanese PWR plant is described. A feasibility study of component risk raking for plant maintenance optimization is performed on check valves and motor-operated valves. Risk ranking is performed in two steps using probabilistic analysis (quantitative method) for risk ranking of components, and deterministic examination (qualitative method) for component review. In this study, plant components are ranked from the viewpoint of plant safety / reliability, and the applicability for maintenance is assessed. As a result, distribution of maintenance resources using risk ranking is considered effective. (author)

  4. A Feasibility Study of Youth Apprenticeship in Arkansas.

    Science.gov (United States)

    Jobs for the Future, Inc., West Somerville, MA.

    A study assessed the feasibility and attractiveness of youth apprenticeship in Arkansas in over 80 interviews with employers in 5 key Arkansas industries and occupations. They were allied health, food processing (equipment repair and maintenance and lab technician/quality control), information services, metalworking, and self-employment and…

  5. Mindfulness and Climate Change Action: A Feasibility Study

    Directory of Open Access Journals (Sweden)

    Maggie Grabow

    2018-05-01

    Full Text Available Pro-environmental behaviors and the cultural shifts that can accompany these may offer solutions to the consequences of a changing climate. Mindfulness has been proposed as a strategy to initiate these types of behaviors. In 2017, we pilot-tested Mindful Climate Action (MCA, an eight-week adult education program that delivers energy use, climate change, and sustainability content in combination with training in mindfulness meditation, among 16 individuals living in Madison, WI. We collected participant data at baseline and at different times across the study period regarding household energy use, transportation, diet, and health and happiness. This pilot study aimed to evaluate the feasibility of the various MCA study practices including measurement tools, outcome assessment, curriculum and related educational materials, and especially the mindfulness-based climate action trainings. MCA was well-received by participants as evidenced by high adherence rate, high measures of participant satisfaction, and high participant response rate for surveys. In addition, we successfully demonstrated feasibility of the MCA program, and have estimated participant’s individual carbon footprints related to diet, transportation, and household energy.

  6. Radiation processing of fruits and vegetables-a technically and economically feasible technology

    Energy Technology Data Exchange (ETDEWEB)

    Moy, J H

    1986-12-31

    Exporting fresh tropical fruits and vegetables to non-infested areas often requires an approved and efficacious quarantine treatment. The feasibility and efficacy of the gamma-radiation process has been demonstrated through quality retention of fresh commodities irradiated at 0.26-0.30 kGy for fruit fly control. Experimental results have shown that papayas and mangoes can be irradiated at up to 1.0 kGy without any adverse effects on their organoleptic and nutrient qualities. Thus it is possible to combine irradiation within this dose level with other techniques to extend the shelf-life of fruits. For example, the shelf-life of papayas can be extended 3-4 days longer after hot water treatment (49 degrees C for 20 minutes for decay control followed by gamma-radiation at 0.75 kGy.) Slowing of the fruit`s respiration results in a delay in its ripening. Irradiation at 0.30 to 0.50 kGy preserves the organoleptic qualities of California citrus and stone fruits. Citrus can tolerate higher doses than stone fruits especially if refrigeration follows irradiation. The extension of shelf-life of irradiated onions and potatoes at low dose (0.02 - 0.15 kGy) through sprout inhibition has been established by a number of studies. The prospect of low dose irradiation of fruits and vegetables is good because problems previously existing as barriers to early commercialization of the radiation process are being resolved. These include: government regulations; economic feasibility; and industry interest. Further efforts are needed, however, to develop international trade agreements on irradiated foods and to launch a consumer education program so as to instil confidence and increase consumer acceptance of the safety and benefits of irradiated foods

  7. Radiation processing of fruits and vegetables-a technically and economically feasible technology

    International Nuclear Information System (INIS)

    Moy, J. H.

    1985-01-01

    Exporting fresh tropical fruits and vegetables to non-infested areas often requires an approved and efficacious quarantine treatment. The feasibility and efficacy of the gamma-radiation process has been demonstrated through quality retention of fresh commodities irradiated at 0.26-0.30 kGy for fruit fly control. Experimental results have shown that papayas and mangoes can be irradiated at up to 1.0 kGy without any adverse effects on their organoleptic and nutrient qualities. Thus it is possible to combine irradiation within this dose level with other techniques to extend the shelf-life of fruits. For example, the shelf-life of papayas can be extended 3-4 days longer after hot water treatment (49 degrees C for 20 minutes for decay control followed by gamma-radiation at 0.75 kGy.) Slowing of the fruit's respiration results in a delay in its ripening. Irradiation at 0.30 to 0.50 kGy preserves the organoleptic qualities of California citrus and stone fruits. Citrus can tolerate higher doses than stone fruits especially if refrigeration follows irradiation. The extension of shelf-life of irradiated onions and potatoes at low dose (0.02 - 0.15 kGy) through sprout inhibition has been established by a number of studies. The prospect of low dose irradiation of fruits and vegetables is good because problems previously existing as barriers to early commercialization of the radiation process are being resolved. These include: government regulations; economic feasibility; and industry interest. Further efforts are needed, however, to develop international trade agreements on irradiated foods and to launch a consumer education program so as to instil confidence and increase consumer acceptance of the safety and benefits of irradiated foods

  8. Methodology study: Co-generation feasibility at sawmills

    International Nuclear Information System (INIS)

    Host, J.

    1991-01-01

    This report discussed the various factors that should be studied and evaluated before establishing a cogeneration plant. The results of three case studies and a survey of energy needs in smaller and medium size sawmills are also presented. In general, cogeneration is feasible for supplying electric energy required for processing logs using fuelbark and other residues from the manufacturing process. A rebuilt turbine-generator unit is an initial cost saving alternative that is advantageous throughout the life of the operation

  9. Defining Feasibility and Pilot Studies in Preparation for Randomised Controlled Trials: Development of a Conceptual Framework.

    Directory of Open Access Journals (Sweden)

    Sandra M Eldridge

    Full Text Available We describe a framework for defining pilot and feasibility studies focusing on studies conducted in preparation for a randomised controlled trial. To develop the framework, we undertook a Delphi survey; ran an open meeting at a trial methodology conference; conducted a review of definitions outside the health research context; consulted experts at an international consensus meeting; and reviewed 27 empirical pilot or feasibility studies. We initially adopted mutually exclusive definitions of pilot and feasibility studies. However, some Delphi survey respondents and the majority of open meeting attendees disagreed with the idea of mutually exclusive definitions. Their viewpoint was supported by definitions outside the health research context, the use of the terms 'pilot' and 'feasibility' in the literature, and participants at the international consensus meeting. In our framework, pilot studies are a subset of feasibility studies, rather than the two being mutually exclusive. A feasibility study asks whether something can be done, should we proceed with it, and if so, how. A pilot study asks the same questions but also has a specific design feature: in a pilot study a future study, or part of a future study, is conducted on a smaller scale. We suggest that to facilitate their identification, these studies should be clearly identified using the terms 'feasibility' or 'pilot' as appropriate. This should include feasibility studies that are largely qualitative; we found these difficult to identify in electronic searches because researchers rarely used the term 'feasibility' in the title or abstract of such studies. Investigators should also report appropriate objectives and methods related to feasibility; and give clear confirmation that their study is in preparation for a future randomised controlled trial designed to assess the effect of an intervention.

  10. Defining Feasibility and Pilot Studies in Preparation for Randomised Controlled Trials: Development of a Conceptual Framework.

    Science.gov (United States)

    Eldridge, Sandra M; Lancaster, Gillian A; Campbell, Michael J; Thabane, Lehana; Hopewell, Sally; Coleman, Claire L; Bond, Christine M

    2016-01-01

    We describe a framework for defining pilot and feasibility studies focusing on studies conducted in preparation for a randomised controlled trial. To develop the framework, we undertook a Delphi survey; ran an open meeting at a trial methodology conference; conducted a review of definitions outside the health research context; consulted experts at an international consensus meeting; and reviewed 27 empirical pilot or feasibility studies. We initially adopted mutually exclusive definitions of pilot and feasibility studies. However, some Delphi survey respondents and the majority of open meeting attendees disagreed with the idea of mutually exclusive definitions. Their viewpoint was supported by definitions outside the health research context, the use of the terms 'pilot' and 'feasibility' in the literature, and participants at the international consensus meeting. In our framework, pilot studies are a subset of feasibility studies, rather than the two being mutually exclusive. A feasibility study asks whether something can be done, should we proceed with it, and if so, how. A pilot study asks the same questions but also has a specific design feature: in a pilot study a future study, or part of a future study, is conducted on a smaller scale. We suggest that to facilitate their identification, these studies should be clearly identified using the terms 'feasibility' or 'pilot' as appropriate. This should include feasibility studies that are largely qualitative; we found these difficult to identify in electronic searches because researchers rarely used the term 'feasibility' in the title or abstract of such studies. Investigators should also report appropriate objectives and methods related to feasibility; and give clear confirmation that their study is in preparation for a future randomised controlled trial designed to assess the effect of an intervention.

  11. Floating natural gas processing plants. Technical ideal or feasible technology

    Energy Technology Data Exchange (ETDEWEB)

    Backhaus, H

    1977-04-01

    Realizability of floating natural gas processing plants is decisively influenced by the economy of the system. Illustrated by the example of the natural gas product LPG (liquefied petroleum gas), a model cost calculation is carried out. It is demonstrated that the increase in the price level during the 1973/1974 energy crisis is an important factor for the realiability in terms of economy of such complicated technical systems. Another aspect which the model calculation revealed is that the economy of floating natural gas processing plants and storage systems can only be estimated in connection with other system components.

  12. Implementation of an electronic fingerprint-linked data collection system: a feasibility and acceptability study among Zambian female sex workers.

    Science.gov (United States)

    Wall, Kristin M; Kilembe, William; Inambao, Mubiana; Chen, Yi No; Mchoongo, Mwaka; Kimaru, Linda; Hammond, Yuna Tiffany; Sharkey, Tyronza; Malama, Kalonde; Fulton, T Roice; Tran, Alex; Halumamba, Hanzunga; Anderson, Sarah; Kishore, Nishant; Sarwar, Shawn; Finnegan, Trisha; Mark, David; Allen, Susan A

    2015-06-27

    Patient identification within and between health services is an operational challenge in many resource-limited settings. When following HIV risk groups for service provision and in the context of vaccine trials, patient misidentification can harm patient care and bias trial outcomes. Electronic fingerprinting has been proposed to identify patients over time and link patient data between health services. The objective of this study was to determine 1) the feasibility of implementing an electronic-fingerprint linked data capture system in Zambia and 2) the acceptability of this system among a key HIV risk group: female sex workers (FSWs). Working with Biometrac, a US-based company providing biometric-linked healthcare platforms, an electronic fingerprint-linked data capture system was developed for use by field recruiters among Zambian FSWs. We evaluated the technical feasibility of the system for use in the field in Zambia and conducted a pilot study to determine the acceptability of the system, as well as barriers to uptake, among FSWs. We found that implementation of an electronic fingerprint-linked patient tracking and data collection system was feasible in this relatively resource-limited setting (false fingerprint matching rate of 1/1000 and false rejection rate of lodges) could be addressed by recruiting women during less busy hours, in their own homes, in the presence of "Queen Mothers" (FSW organizers), or in the presence of a FSW that has already been fingerprinted. Our findings have major implications for key population research and improved health services provision. However, more work needs to be done to increase the acceptability of the electronic fingerprint-linked data capture system during field recruitment. This study indicated several potential avenues that will be explored to increase acceptability.

  13. Feasibility study of upgrading Byllesby and Buck power plants on the New River in the Commonwealth of Virginia

    Energy Technology Data Exchange (ETDEWEB)

    1979-05-01

    The feasibility of upgrading alternatives of the 66-year-old Byllesby and Buck hydroelectric developments located on the New River in Virginia was investigated. Evaluation of technical, economic and environmental factors led to the conclusion that modernization of the plants could result in an annual generation increase of 20.2 GWh at a cost of $6.1 million and with a benefit-cost ratio of 2.32. The recommended retrofitting includes replacing existing runners with new, more efficiently designed runners, modifying draft tube and wicker gate, and rewinding the generators. (LCL)

  14. Feasibility studies - Oesthammar, Nykoeping, Oskarshamn, Tierp, Hultsfred and Aelvkarleby. Summary report

    International Nuclear Information System (INIS)

    2001-06-01

    Swedish Nuclear Fuel and Waste Management Company, SKB, has carried out feasibility studies on a municipal scale as a part of the siting programme for the deep repository for spent nuclear fuel. Final reports describing the results of the six feasibility studies in Oesthammar, Nykoeping, Oskarshamn, Tierp, Aelvkarleby and Hultsfred were submitted during the autumn and winter of 2000/2001. With this as a basis, the siting work can now proceed to the next phase - site investigations. In this stage, investigations that include test drilling will be conducted on at least two sites. In December 2000, SKB published the report 'Integrated account of method, site selection and programme prior to the site investigation phase', in which SKB stipulates where they want to conduct site investigations and how they will be carried out. The report is being reviewed by the Swedish Nuclear Power Inspectorate during the first half of 2001. Before the site investigations can be initiated,the go-ahead is required from the national safety authorities, the Government, and concerned municipalities and landowners. SKB projects that the it will be possible to commence the site investigations in 2002. This report comprises an English summary of the final reports from the six feasibility studies. The report summarizes the most important results and conclusions from the different feasibility studies. All six final reports are available in their entirety in Swedish

  15. Feasibility studies - Oesthammar, Nykoeping, Oskarshamn, Tierp, Hultsfred and Aelvkarleby. Summary report

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-06-01

    Swedish Nuclear Fuel and Waste Management Company, SKB, has carried out feasibility studies on a municipal scale as a part of the siting programme for the deep repository for spent nuclear fuel. Final reports describing the results of the six feasibility studies in Oesthammar, Nykoeping, Oskarshamn, Tierp, Aelvkarleby and Hultsfred were submitted during the autumn and winter of 2000/2001. With this as a basis, the siting work can now proceed to the next phase - site investigations. In this stage, investigations that include test drilling will be conducted on at least two sites. In December 2000, SKB published the report 'Integrated account of method, site selection and programme prior to the site investigation phase', in which SKB stipulates where they want to conduct site investigations and how they will be carried out. The report is being reviewed by the Swedish Nuclear Power Inspectorate during the first half of 2001. Before the site investigations can be initiated,the go-ahead is required from the national safety authorities, the Government, and concerned municipalities and landowners. SKB projects that the it will be possible to commence the site investigations in 2002. This report comprises an English summary of the final reports from the six feasibility studies. The report summarizes the most important results and conclusions from the different feasibility studies. All six final reports are available in their entirety in Swedish.

  16. Pre-feasibility study of 80mw onshore wind farm

    International Nuclear Information System (INIS)

    Almas, M.S.

    2014-01-01

    This paper discusses a pre-feasibility study of 80MW onshore wind farm in the KPK (Khyber Pakhtunkhwa) province previously known as NWFP (North West Frontier) Province of Pakistan. The realistic data of wind speed is collected from Laboratory of Meteorology and Climatology (University of the Punjab) to study the feasibility of wind farm. Detailed analysis of wind turbines from four different manufacturers is carried out together with justifications of selecting a particular wind turbine. Issues related to site selection, wind farm civil foundation, recommendations for a particular choice of tower along with environmental effects are presented. Wind data analysis is carried out by using WINDROSE PRO software to determine the resultant direction of wind at the selected site for wind farm layout. The wind distribution at hub height of the wind turbine is calculated and is used to compute annual power production by the wind farm using power curves of the wind turbine. Electrical network integration issues of wind farm to the external grid are studied and the optimum point of connection is proposed. Finally, economic analysis of the whole wind farm project depending upon the LCC (Life Cycle Cost Analysis) is presented and the feasibility of the project from the investor's point of view is identified. The study concludes that the cost per kilowatt hour of electricity generated by this wind power plant will be 10.4 PKR/kWh and the payback period for the whole project is about 11.2 years. (author)

  17. Study of the method of placing technical stations

    Directory of Open Access Journals (Sweden)

    Sattorov S.B.

    2017-12-01

    Full Text Available At present, the organization of transportation by rail is associated with the processing of trains and wagons along the route. Accommodation and equipping of technical stations play a major role in the organization of the transportation process. The uninterrupted operation of the technical stations ensures the stability of the railway transport as a whole. The distance between the technical stations determines the duration of operation of the locomotive crew, the efficient use of the locomotive, the required number of locomotive crews and locomotives for carrying out the transportation plan, and also improves the main indicators of the railway. However, often train locomotives do not fulfill their assigned tasks due to the lack of time for the locomotive crew in order to deliver the train to the nearest technical station, as well as the irrational use of the standard time of the locomotive crew. In connection with the expectation of delivery, the locomotive brigade replacing the locomotive, the idle time of the wagons at the intermediate stations increases. All this makes it difficult to control the movement of trains and reduces the speed of moving cars on the railway transport. The purpose of the study is to develop a method for placing technical stations on a railway test site in the course of an electric traction. To achieve this goal, it will be necessary to solve the following tasks: generalization of the main parameters of the location of technical stations; determination of half-races between technical stations in the operation of one locomotive brigade; search for the required number of change of the locomotive brigade; determination of the distance between technical stations. The methods of research are based on the generalization and analysis of existing results in finding the rational location of technical stations. Results: It is revealed that the first step for the rational placement of technical stations is to determine the

  18. Staging and storage facility feasibility study. Final report

    International Nuclear Information System (INIS)

    Swenson, C.E.

    1995-02-01

    This study was performed to investigate the feasibility of adapting the design of the HWVP Canister Storage Building (CSB) to meet the needs of the WHC Spent Nuclear Fuel Project for Staging and Storage Facility (SSF), and to develop Rough Order of Magnitude (ROM) cost and schedule estimates

  19. Feasibility Study of a Solar-Powered Electric Vehicle Charging Station Model

    Directory of Open Access Journals (Sweden)

    Bin Ye

    2015-11-01

    Full Text Available In China, the power sector is currently the largest carbon emitter and the transportation sector is the fastest-growing carbon emitter. This paper proposes a model of solar-powered charging stations for electric vehicles to mitigate problems encountered in China’s renewable energy utilization processes and to cope with the increasing power demand by electric vehicles for the near future. This study applies the proposed model to Shenzhen City to verify its technical and economic feasibility. Modeling results showed that the total net present value of a photovoltaic power charging station that meets the daily electricity demand of 4500 kWh is $3,579,236 and that the cost of energy of the combined energy system is $0.098/kWh. In addition, the photovoltaic powered electric vehicle model has pollutant reduction potentials of 99.8%, 99.7% and 100% for carbon dioxide, sulfur dioxide, and nitrogen oxides, respectively, compared with a traditional gasoline-fueled car. Sensitivity analysis results indicated that interest rate has a relatively strong influence on COE (Cost of Energy. An increase in the interest rate from 0% to 6% increases COE from $0.027/kWh to $0.097/kWh. This analysis also suggests that carbon pricing promotes renewable energy only when the price of carbon is above $20/t.

  20. Evaluation of Technical Feasibility of Homogeneous Charge Compression Ignition (HCCI) Engine Fueled with Hydrogen, Natural Gas, and DME

    Energy Technology Data Exchange (ETDEWEB)

    Pratapas, John; Mather, Daniel; Kozlovsky, Anton

    2013-03-31

    The objective of the proposed project was to confirm the feasibility of using blends of hydrogen and natural gas to improve the performance, efficiency, controllability and emissions of a homogeneous charge compression ignition (HCCI) engine. The project team utilized both engine simulation and laboratory testing to evaluate and optimize how blends of hydrogen and natural gas fuel might improve control of HCCI combustion. GTI utilized a state-of-the art single-cylinder engine test platform for the experimental work in the project. The testing was designed to evaluate the feasibility of extending the limits of HCCI engine performance (i.e., stable combustion, high efficiency and low emissions) on natural gas by using blends of natural gas and hydrogen. Early in the project Ricardo provided technical support to GTI as we applied their engine performance simulation program, WAVE, to our HCCI research engine. Modeling support was later provided by Digital Engines, LLC to use their proprietary model to predict peak pressures and temperatures for varying operating parameters included in the Design of Experiments test plan. Digital Engines also provided testing support for the hydrogen and natural gas blends. Prof. David Foster of University of Wisconsin-Madison participated early in the project by providing technical guidance on HCCI engine test plans and modeling requirements. The main purpose of the testing was to quantify the effects of hydrogen addition to natural gas HCCI. Directly comparing straight natural gas with the hydrogen enhanced test points is difficult due to the complexity of HCCI combustion. With the same air flow rate and lambda, the hydrogen enriched fuel mass flow rate is lower than the straight natural gas mass flow rate. However, the energy flow rate is higher for the hydrogen enriched fuel due to hydrogen’s significantly greater lower heating value, 120 mJ/kg for hydrogen compared to 45 mJ/kg for natural gas. With these caveats in mind, an

  1. Status of Recent Developments in the Technical Standards of Japan

    International Nuclear Information System (INIS)

    Ahn, Hyung-Joon; Ahn, Sang-Kyu; Koh, Jae-Dong; Kim, Chang-Bum

    2006-01-01

    Japan has systematically revamped its technical standards for nuclear reactor facilities by formulating various performance regulations. Being part of a trend toward deregulation, such efforts toward social regulation is aimed at effectively operating administrative procedural laws to keep pace with global trends and enhance the benefits of deregulation under the principle of self-responsibility. Based on the collection of public opinions in February and March 2005, the Nuclear and Industrial Safety Agency(NISA) presented its position that it was required to promptly perform a flexible assessment of the technical feasibility of formulated society and association standards. Current, pressing issues are summarized as an early revision of technical standards regarding nuclear facilities for power generation, use of society and association standards, and the overhaul of nuclear safety regulations subject to performance regulations. Subjecting technical standards to performance regulations means stipulating the qualitative aspects of performance and the targets that certain facilities must achieve, which are not specific standards, but general compulsory standards. This study examines the early revision of technical standards on nuclear facilities for power generation and the status of the use of society and association standards, as well as introducing the details of revisions in the concrete containment vessel standards as specific examples

  2. Design of subjects training on reactor simulator and feasibility study - toward the empirical evaluation of interface design concept

    International Nuclear Information System (INIS)

    Yamaguchi, Y.; Furukawa, H.; Tanabe, F.

    1998-01-01

    On-going JAERI's project for empirical evaluation of the ecological interface design concept was first described. The empirical evaluation is planned to be proceeded through three consecutive steps; designing and actual implementation of the interface on reactor simulator, verification of the interface created, and the validation by the simulator experiment. For conducting the project, three different experimental resources are prerequisite, that are, data analysis method for identifying the operator's strategies, experimental facility including reactor simulator, and experimental subjects or subjects training method. Among the three experimental resources, subjects training method was recently designed and a simulator experiment was earned out in order to examine the feasibility of the designed training method. From the experiment and analysis of the experimental records, we could conclude that it is feasible that the experimental subjects having an appropriate technical basis can gain the sufficient competence for evaluation work of the interface design concept by using the training method designed. (author)

  3. Feasibility study: Assess the feasibility of siting a monitored retrievable storage facility. Phase 1

    Energy Technology Data Exchange (ETDEWEB)

    King, J.W.

    1993-08-01

    The purpose of phase one of this study are: To understand the waste management system and a monitored retrievable storage facility; and to determine whether the applicant has real interest in pursuing the feasibility assessment process. Contents of this report are: Generating electric power; facts about exposure to radiation; handling storage, and transportation techniques; description of a proposed monitored retrievable storage facility; and benefits to be received by host jurisdiction.

  4. Case study of an organic Rankine cycle applied for excess heat recovery: Technical, economic and policy matters

    International Nuclear Information System (INIS)

    Lemmens, Sanne; Lecompte, Steven

    2017-01-01

    Highlights: • Case study of an organic Rankine cycle for heat recovery from an industrial kiln. • The costs and financial feasibility of the system are discussed in detail. • The cost structure is most defined by the capital costs, annual costs are limited. • The system is financially feasible, but subsidies remain important. • The results are most sensitive to changes in load hours and electricity price. - Abstract: Many industrial processes inevitably produce excess heat as by-product. Recovering this heat is a matter of waste management and provides opportunities to improve the energy use efficiency. The excess heat can be used for heating purposes (e.g., in processes, or delivered to district heating systems or buildings) or to generate electricity. An increasingly applied technology for industrial excess heat recovery is the organic Rankine cycle (ORC), suitable to recover low-grade heat from 90 °C onwards. Although ORCs are studied intensively, few studies have examined the economics of commissioned ORC systems. This paper investigates a 375 kW_g_r_o_s_s ORC system employed for flue gas heat recovery from an industrial kiln in Flanders, Belgium. The purpose of the study is twofold: providing insight into a practical ORC case; and evaluating the financial feasibility while taking the specific policy circumstances into account. The financial appraisal takes account of the specific technical setup, the diverse costs of the system, the external economic parameters, and the policy circumstances in Europe, Belgium and Flanders. A sensitivity analysis illustrates the influence of each parameter on the results. The analysis demonstrates the dominance of the investment costs (4217 €_2_0_1_3/kW_g_r_o_s_s) in the expenses. Under the valid conditions the investment has a positive financial return, but the financial support from the government is indispensable. Finally, the sensitivity analysis reveals the importance of attaining sufficient load hours and the

  5. Feasibility study of full-reactor gas core demonstration test

    Science.gov (United States)

    Kunze, J. F.; Lofthouse, J. H.; Shaffer, C. J.; Macbeth, P. J.

    1973-01-01

    Separate studies of nuclear criticality, flow patterns, and thermodynamics for the gas core reactor concept have all given positive indications of its feasibility. However, before serious design for a full scale gas core application can be made, feasibility must be shown for operation with full interaction of the nuclear, thermal, and hydraulic effects. A minimum sized, and hence minimum expense, test arrangement is considered for a full gas core configuration. It is shown that the hydrogen coolant scattering effects dominate the nuclear considerations at elevated temperatures. A cavity diameter of somewhat larger than 4 ft (122 cm) will be needed if temperatures high enough to vaporize uranium are to be achieved.

  6. Technical and economic analysis of hydrogen refuelling

    International Nuclear Information System (INIS)

    Nistor, Silviu; Dave, Saraansh; Fan, Zhong; Sooriyabandara, Mahesh

    2016-01-01

    Highlights: • Technical and economic models of a hydrogen station for vehicles refuelling. • Hydrogen demand from fuel cell electric vehicles modelled stochastically. • Study case based on a UK pilot project. • Operation of the H_2 station using combined energy from wind and power grid is preferred. • Return on investment of 5–10 years is possible for the hydrogen station. - Abstract: This paper focuses on technical and economic analysis of a hydrogen refilling station to provide operational insight through tight coupling of technical models of physical processes and economic models. This allows the dynamic relationships of the system to be captured and analysed to provide short/medium term analytical capability to support system design, planning, and financing. The modelling developed here highlights the need to closely link technical and economic models for technology led projects where technical capability and commercial feasibility are important. The results show that hydrogen fuel can be competitive with petrol on a GBP/KG basis if the return on investment period is over 10 years for PEM electrolysers and 5 for Alkaline electrolysers. We also show that subsidies on capital costs (as reflected by some R&D funding programs) make both PEM and Alkaline technologies cheaper than the equivalent price of petrol, which suggests more emphasis should be put on commercialising R&D funded projects as they have commercial advantages. The paper also shows that a combined wind and grid connected station is preferable so that a higher number of customers are served (i.e. minimum shortage of hydrogen).

  7. Feasibility Study and Optimization of An Hybrid System (Eolian ...

    African Journals Online (AJOL)

    Feasibility Study and Optimization of An Hybrid System (Eolian- Photovoltaic - Diesel) With Provision of Electric Energy Completely Independent. ... reducing emissions of greenhouse gas (CO2 rate = 16086 kg / year for a system using only the generator diesel and is 599 kg / year for the stand alone hybrid system studied).

  8. Feasible way of Human Solid and Liquid Wastes' Inclusion Into Intersystem Mass Exchange of Biological-Technical Life Support Systems

    Science.gov (United States)

    Ushakova, Sofya; Tikhomirov, Alexander A.; Tikhomirova, Natalia; Kudenko, Yurii; Griboskaya, Illiada; Gros, Jean-Bernard; Lasseur, Christophe

    The basic objective arising at use of mineralized human solid and liquid wastes serving as the source of mineral elements for plants cultivation in biological-technical life support systems appears to be NaCl presence in them. The given work is aimed at feasibility study of mineralized human metabolites' utilization for nutrient solutions' preparation for their further employment at a long-term cultivation of uneven-aged wheat and Salicornia europaea L. cenosis in a conveyer regime. Human solid and liquid wastes were mineralized by the "wet incineration" method developed by Yu. Kudenko. On their base the solutions were prepared which were used for cultivation of 5-aged wheat conveyer with the time step-interval of 14 days. Wheat was cultivated by hydroponics method on expanded clay aggregate. For partial demineralization of nutrient solution every two weeks after regular wheat harvesting 12 L of solution was withdrawn from the wheat irrigation tank and used for Salicornia europaea cultivation by the water culture method in a conveyer regime. The Salicornia europaea conveyer was represented by 2 ages with the time step-interval of 14 days. Resulting from repeating withdrawal of the solution used for wheat cultivation, sodium concentration in the wheat irrigation solution did not exceed 400 mg/l, and mineral elements contained in the taken solution were used for Salicornia europaea cultivation. The experiment lasted 7 months. Total wheat biomass productivity averaged 30.1 g*m-2*day-1 at harvest index equal to 36.8The work was carried out under support of SB RAS grant 132 and INTAS 05-1000008-8010

  9. Technical aspects of 3MV particle accelerator at GGV Bilaspur

    International Nuclear Information System (INIS)

    Mallik, C.

    2013-01-01

    The accelerator at GGV, Bilaspur is a 3 MV pelletron operating is Tandem mode. The talk will describe the technical aspects of the accelerator. It will also discuss the beam aspects of the pelletron and the feasibility options with the accelerator. (author)

  10. Feasibility study of geospatial mapping of chronic disease risk to inform public health commissioning.

    Science.gov (United States)

    Noble, Douglas; Smith, Dianna; Mathur, Rohini; Robson, John; Greenhalgh, Trisha

    2012-01-01

    To explore the feasibility of producing small-area geospatial maps of chronic disease risk for use by clinical commissioning groups and public health teams. Cross-sectional geospatial analysis using routinely collected general practitioner electronic record data. Tower Hamlets, an inner-city district of London, UK, characterised by high socioeconomic and ethnic diversity and high prevalence of non-communicable diseases. The authors used type 2 diabetes as an example. The data set was drawn from electronic general practice records on all non-diabetic individuals aged 25-79 years in the district (n=163 275). The authors used a validated instrument, QDScore, to calculate 10-year risk of developing type 2 diabetes. Using specialist mapping software (ArcGIS), the authors produced visualisations of how these data varied by lower and middle super output area across the district. The authors enhanced these maps with information on examples of locality-based social determinants of health (population density, fast food outlets and green spaces). Data were piloted as three types of geospatial map (basic, heat and ring). The authors noted practical, technical and information governance challenges involved in producing the maps. Usable data were obtained on 96.2% of all records. One in 11 adults in our cohort was at 'high risk' of developing type 2 diabetes with a 20% or more 10-year risk. Small-area geospatial mapping illustrated 'hot spots' where up to 17.3% of all adults were at high risk of developing type 2 diabetes. Ring maps allowed visualisation of high risk for type 2 diabetes by locality alongside putative social determinants in the same locality. The task of downloading, cleaning and mapping data from electronic general practice records posed some technical challenges, and judgement was required to group data at an appropriate geographical level. Information governance issues were time consuming and required local and national consultation and agreement. Producing

  11. Utility scale wind turbines on a grid-connected island: A feasibility study

    Energy Technology Data Exchange (ETDEWEB)

    Dua, Mohit; Manwell, James F.; McGowan, Jon G. [Department of Mechanical and Industrial Engineering, Renewable Energy Research Laboratory (RERL), University of Massachusetts, Amherst, MA 01003 (United States)

    2008-04-15

    This paper analyzes the technical and economic feasibility of installing utility-scale wind turbines on the Fox Islands, located 12 miles from the coast of Maine in the United States. Three locations on the islands, as well as a near offshore site, are analyzed in detail as potential sites for wind turbine installations. As discussed in this work, the logistic problems of transporting and installing wind turbines on the island require innovative solutions. These include locally available amphibious vessels, which can land turbine components at suitable shallow spots on the island, self-erecting towers, which allow use of a smaller crane for installation, and a special turbine foundation suitable for the local ground conditions. In the economic analysis, in addition to standard life-cycle parameters, renewable energy credits (REC) were also included. This work concludes that the installation of sub-megawatt wind turbines on the island is logistically possible and will lead to a reduction in the cost of electricity to the customers. (author)

  12. Engineering management at feasibility study stage of nuclear power plant under EPC mode

    International Nuclear Information System (INIS)

    Wang Zhiqiang

    2015-01-01

    After the investment reform by the State Council in 2004, NDRC carries out approval system for enterprises to invest in nuclear power plants. Feasibility study stage is a critical stage on the mainline of nuclear power project approval, which intersects with the license application, and engineering design. The owners of nuclear power plants are required stringently in engineering management. From the owners' management point of view under EPC mode, this paper sorts the preliminary project process for nuclear power plants, focusing on the management in the feasibility study stage. License application and engineering design management in the feasibility study stage are also discussed. (author)

  13. Feasibility of waste gas turbogenerators on motor ships

    Energy Technology Data Exchange (ETDEWEB)

    Steczek, M

    1979-01-01

    Using the waste gas energy, on any motor ship, electrical energy can be generated by means of a vapour cycle process without fuel costs. In the article, it is shown that engine performance on such a waste gas turbo generator can generate the power needed on board for operating the ship. This technical investigation is followed by a feasibility calculation which shows that such an installation is paid off very quickly with today's fuel costs.

  14. Safety and Feasibility of Transradial Access for Visceral Interventions in Patients with Thrombocytopenia.

    Science.gov (United States)

    Titano, J J; Biederman, D M; Marinelli, B S; Patel, R S; Kim, E; Tabori, N E; Nowakowski, F S; Lookstein, R A; Fischman, A M

    2016-05-01

    Transradial access (TRA) has shown lower morbidity and decreased bleeding complications compared to transfemoral access. This study evaluates the safety and