Comparisons of FCC product yields and qualities between reactors using Canadian heavy feeds

Energy Technology Data Exchange (ETDEWEB)

Ng, Siauw H.; Fairbridge, Craig; Khulbe, Chandra [National Centre for Upgrading Technology, 1 Oil Patch Drive, Devon, Alberta (Canada); Humphries, Adrian [Akzo Nobel Catalysts LLC., 2625 Bay Area Boulevard, Suite 250, Houston, TX 77058 (United States); Zhu, Yuxia [Research Institute of Petroleum Processing, 18 Xue Yuen Road, PO Box 914, Beijing 100083 (China); Tsai, Thomas Y.R. [National Dong Hwa University, Hualien 974 (Taiwan); Ding, Fuchen [University of Petroleum, Beijing 102249 (China); Charland, Jean-Pierre [CANMET Energy Technology Centre-Ottawa, 1 Haanel Drive, Ottawa, Ontario (Canada); Yui, Sok [Syncrude, Research Centre, 9421-17 Avenue, Edmonton, Alberta (Canada)

2005-08-25

This study describes the effects of two catalysts, an octane-barrel and a bottoms-cracking catalyst, on the catalytic cracking of 10 oil-sands bitumen-derived feeds in fixed- and fluid-bed microactivity test (MAT) units, an Advanced Cracking Evaluation (ACE) unit, and a continuous riser pilot unit. This is part of a comprehensive study of the cracking behavior of Canadian vacuum gas oils. In general, at an equivalent catalyst/oil ratio, conversions decreased in the order ACE>fixed-bed MAT>fluid-bed MAT among the batch reactors. Between a batch reactor and the continuous riser, there existed a good correlation for a given product yield as well as for a given product quality, at a specific conversion. For the oil-sands-derived vacuum gas oils, the bottoms-cracking catalyst containing rare-earth-exchanged Y zeolite (REY) with a large-pore active matrix was more effective than the catalyst containing the rare-earth-exchanged ultrastable Y (REUSY) and ZSM-5 zeolites with an active matrix. The overall distribution of feed sulfur in cracked products, and the relationship of the sulfur content of feed with that of light cycle oil (LCO), confirmed the findings reported in the literature.

Prediction of gasoline yield in a fluid catalytic cracking (FCC riser using k-epsilon turbulence and 4-lump kinetic models: A computational fluid dynamics (CFD approach

Directory of Open Access Journals (Sweden)

Muhammad Ahsan

2015-07-01

Full Text Available Fluid catalytic cracking (FCC is an essential process for the conversion of gas oil to gasoline. This study is an effort to model the phenomenon numerically using commercial computational fluid dynamics (CFD software, heavy density catalyst and 4-lump kinetic model. Geometry, boundary conditions and dimensions of industrial riser for catalytic cracking unit are conferred for 2D simulation using commercial CFD code FLUENT 6.3. Continuity, momentum, energy and species transport equations, applicable to two phase solid and gas flow, are used to simulate the physical phenomenon as efficient as possible. This study implements and predicts the use of the granular Eulerian multiphase model with species transport. Time accurate transient problem is solved with the prediction of mass fraction profiles of gas oil, gasoline, light gas and coke. The output curves demonstrate the breaking of heavy hydrocarbon in the presence of catalyst. An approach proposed in this study shows good agreement with the experimental and numerical data available in the literature.

Uncertainty evaluation by gamma transmission measurements and CFD model comparison in a FCC cold pilot unit

Directory of Open Access Journals (Sweden)

Dantas C.C.

2013-01-01

Full Text Available The solid flow in air-catalyst in circulating fluidized bed was simulated with CFD model to obtain axial and radial distribution. Therefore, project parameters were confirmed and steady state operation condition was improved. Solid holds up axial end radial profiles simulation and comparison with gamma transmission measurements are in a good agreement. The transmission signal from an 241Am radioactive source was evaluated in NaI(Tl detector coupled to multichannel analyzer. This non intrusive measuring set up is installed at riser of a cold pilot unit to determine parameters of FCC catalyst flow at several concentrations. Mass flow rate calculated by combining solid hold up and solid phase velocity measurements was compared with catalyst inlet measured at down-comer. Evaluation in each measured parameter shows that a relative combined uncertainty of 6% in a 95% interval was estimated. Uncertainty analysis took into account a significant correlation in scan riser transmission measurements. An Eulerian approach of CFD model incorporating the kinetic theory of granular flow was adopted to describe the gas–solid two-phase flows in a multizone circulating reactor. Instantaneous and local gas-particle velocity, void fraction and turbulent parameters were obtained and results are shown in 2 D and 3D graphics.

Validation Plan of Turbulence Models for Internal Gas Flow Analysis in a Heated Rectangular Riser Duct

Energy Technology Data Exchange (ETDEWEB)

Kim, Sin-Yeob; Shin, Dong-Ho; Park, Goon-Cherl; Cho, Hyoung Kyu [Seoul National Univ., Seoul (Korea, Republic of); Kim, Chan-Soo [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2016-10-15

VHTR being developed at Korea Atomic Energy Research Institute adopts an air-cooled Reactor Cavity Cooling System (RCCS) incorporating rectangular riser channels to remove the afterheat emitted from the reactor vessel. Because the performance of RCCS is determined by heat removal rate through the RCCS riser, it is important to understand the heat transfer phenomena in the RCCS riser to ensure the safety of the reactor. In the mixed convection, due to the buoyance force induced by temperature and density differences, local flow structure and heat transfer mode near the heated wall have significantly dissimilar characteristics from both forced convection and free convection. In this study, benchmark calculation was conducted to reproduce the previous statements that V2F turbulence model can capture the mixed convection phenomena with the Shehata's experimental data. Then, the necessity of the model validation for the mixed convection phenomena was confirmed with the CFD analyses for the geometry of the prototype RCCS riser. For the purpose of validating the turbulence models for mixed convection phenomena in the heated rectangular riser duct, validation plan with three experimental tests was introduced. Among them, the flow visualization test facility with preserved cross-section geometry was introduced and a preliminary test result was shown.

Modelling of FCC (Fluid Catalytic Cracking) risers with six lumps; Modelo de elevadores de Unidades de Craqueamento Catalitico com cinetica de seis classes

Energy Technology Data Exchange (ETDEWEB)

Baldessar, Fabio; Negrao, Cezar O. Ribeiro; Palu, Claudia [Centro Federal de Educacao Tecnologica do Parana (CEFET-PR), Curitiba, PR (Brazil)

2004-07-01

The current work presents a mathematical model of an ascendant flow vertical reactor (riser) of a Fluid Catalytic Cracking Unit. The two-phase flow (gas-solid) and the cracking reactions are admitted one-dimensional and steady state. Mass, momentum and energy conservation equations are considered for each phase (solid and gas). A six-lump kinetic model is employed to evaluate gasoil, gasoline, GLP, fuel gas, light cycle oil and coke fractions. The model results are compared to experimental values from a pilot plant and to another model found in the literature. The results are in good agreement, showing the model has great potential. (author)

Measurement of density distribution of a cracking catalyst in experimental riser with a sampling procedure for gamma ray tomography

International Nuclear Information System (INIS)

Dantas, C.C.; Melo, S.B.; Oliveira, E.F.; Simoes, F.P.M.; Santos, M.G. dos; Santos, V.A. dos

2008-01-01

By scanning a riser the number of the gamma ray trajectories and the beam width involve temporal, spatial and density resolutions as they are closely correlated parameters. Therefore, evaluation of parameters and their interaction quantification, certainly, are required in the imaging process. Measuring the density distribution of the catalyst from the FCC - fluid cracking catalytic process in an experimental riser in single beam tomographic system, density resolution is evaluated and correlated with spatial resolution. The beam width Δs inside riser is measured and a criterion for determining spatial resolution is proposed. Experiments are carried out to demonstrate resolution effects of three Δs values: 3.30 x 10 -3 , 6.20 x 10 -3 and 12.00 x 10 -3 m. The gamma beam profile is modeled and a sampling rate according to Nyquist criterion is analyzed. The 4.3%, 8.1% and 15.6% ratios of Δs/R to internal riser radius are correlated to counting time in the sampling procedure. Results are discussed by comparison with values from literature

Riser pipe elevator

Energy Technology Data Exchange (ETDEWEB)

Bennett, W.; Jimenez, A.F.

1987-09-08

This patent describes a method for storing and retrieving a riser pipe, comprising the steps of: providing an upright annular magazine comprised of an inside annular wall and an outside annular wall, the magazine having an open top; storing the riser pipe in a substantially vertically oriented position within the annular magazine; and moving the riser pipe upwardly through the open top of the annular magazine at an angle to the vertical along at least a portion of the length of the riser pipe.

Determination of the catalyst circulation rate in a FCC cold flow pilot unit using nuclear techniques

International Nuclear Information System (INIS)

Santos, Valdemir A. dos; Lima, Emerson A.O.

2013-01-01

Nuclear techniques of gamma transmission and radioactive tracer were used to estimate the catalyst circulation rate in a cold flow pilot plant unit of Fluid Catalytic Cracking (FCC). Catalyst circulation rate in a FCC unit, allow to determine operating conditions of the exchange catalyst and inlet data for fluid dynamic simulation computational program. The pilot unit was fabricated obeying geometrical parameters provided by the Petrobras Research Center (CENPES), based on hot pilot units to existing in that center. The cold flow pilot unit has a transfer line, two separation vessels flash type, a return column, a riser and a regenerator. The vertical sections as riser, return column, regenerator column and transfer line are made of transparent material (glass). The two separation vessels have bases with tapered cylindrical shapes and are made of steel plates. The riser is divided into four sections of different diameters (0.005 m, 0.010 m, 0.018 m and 0.025 m) and rising upwards, to simulate the increasing flow rate caused by the increase of volume with the increase of the number of moles due to molecules breakage. The radioactive tracer used was the catalyst itself (intrinsic tracer) irradiated by neutron activation, yielding the radioisotope 59 Fe. The velocity measurements were also obtained with aid of an electronic clock triggered by certain radiation levels across the two detectors. Besides estimates for the catalyst circulation rate was possible to identify the type of flow relative to the catalyst in return column. (author)

Continuous composite riser

Energy Technology Data Exchange (ETDEWEB)

Slagsvold, L. [ABB Offshore Systems (Norway)

2002-12-01

The industry is now looking at developing reserves in waters depths of up to 3000 m (10000 ft). When moving into deeper waters the un-bonded flexible riser becomes very heavy and introduces large hang-off forces on the vessel. We are therefore investigating riser concepts incorporating new materials and with a simpler cross section that can be used for floating production. Advanced composite materials have properties such as, low weight, high strength, good durability and very good fatigue performance. Composite materials are slowly being exploited in the oil industry; they are being prototype tested for drilling risers and small diameter lines. Part of the process for the industry to accept larger diameter production risers made out of composite materials is to understand both the advantages and limitations. A new continuous composite riser system is being developed which capitalizes on the technical benefits of this material while addressing the known constraints. The fully bonded riser is being developed for ultra deep waters and its' characteristics include high temperature (160 deg C), high pressure (500 barg min), light weight, chemical resistant, good insulation, excellent fatigue characteristics and installation by reeling. The concept is based on the use of a thermoplastic liner together with a thermoplastic carbon fibre composite. This paper summarises the ongoing development, which has a goal to manufacture and qualify an 8'' riser, and includes all the steps in a production process from material qualification to the winding process and analytical modelling. (author)

Catalyst volumetric fraction simulation in a riser of a cold flow pilot unit with aid of transmission gamma technique

International Nuclear Information System (INIS)

Santos, Kamylla A.L. dos; Lima Filho, Hilario J.B. de; Benachour, Mohand; Dantas, Carlos C.; Santos, Valdemir A. dos

2013-01-01

Was obtained the radial profile of the catalyst volume fraction in a riser of the cold flow pilot unit of the Fluid Catalytic Cracking (FCC) unit, which was used for adjustment of the entrance conditions of the catalyst in a simulation program by Computational Fluid Dynamics (CFD). The height of the riser of the Cold Flow Pilot Unity (CFPU) utilized is 6.0m and its inner diameter is 0.097 m. A radiation-γ source of Am-241 and a NaI (Tl) detector, with shielding made of lead, have been installed on a steel backing that maintains the geometry of the source-detector-riser and allows to vary the distance from the source to the detector and the radial position in a given cross section of the riser. The data associated with the simulation of volume fraction radial profile of the catalyst were: Fluent software, version 12.0; preprocessor GAMBIT, version 2.3.16; Eulerian approach; structured mesh, cell number of 60000; turbulence model used was k-ε and kinetic theory of granular flow (KTGF) was implemented to describe the solid phase. Comparison of radial profiles simulated and experimental of the catalyst volumetric fraction in the CFPU riser allowed the identification of needs adjustments in the simulation for the input of catalyst, with consequent validation for the proposed model simulation. (author)

Polynomial reconstruction of radial catalyst concentration distribution in an experimental type FCC riser for a low number of transversal projections in gamma ray tomography

International Nuclear Information System (INIS)

Melo, Silvio B.; Simoes, Francisco P.M.; Oliveira, Eric F. de; Santos, Maria das Gracas dos; Dantas, Carlos C.

2007-01-01

In the FCC - Fluid Catalytic Cracking process the Riser is an opaque cylinder, so that, in order to investigate the catalyst concentration inside, a gamma- ray based tomography is employed. Each section is submitted to a parallel beam and by means of the Beer-Lambert transmission is calculated. This tomography session is repeated from different angles, in manual tomographic experiments where the source/detector pair is rotated, producing in each direction what we called a transversal projection. In order to reconstruct the concentration of the present catalyst in a given moment some methods use successfully the inverse Radon transform through the filtered back-projection algorithm. The results are fully satisfactory for a large number of projections, widely seen as better than those produced by the algebraic methods. For a low number of projections, however, the algebraic methods become more competitive. In practice, simple experimental set-ups work with less than 10 projections, due to the time taken by the whole process. In this work, we present an investigation of polynomial reconstructions by using Bezier surfaces of arbitrary degree, adjusted to the experimental data through a least squares method. A computational algorithm was developed to implement the mathematical reconstruction for the 3D graphics presentation. (author)

Key observations from a comprehensive FCC study on Canadian heavy gas oils from various origins: 1. Yield profiles in batch reactors

Energy Technology Data Exchange (ETDEWEB)

Ng, Siauw H.; Nakajima, Nobumasa [National Centre for Upgrading Technology, 1 Oil Patch Drive, Suite A202, Devon, Alberta (Canada T9G 1A8); Zhu, Yuxia [Research Institute of Petroleum Processing, 18 Xue Yuen Road, P.O. Box 914, Beijing 100083 (China); Humphries, Adrian [Albemarle Catalysts Company LP, 2625 Bay Area Blvd., Suite 250, Houston, TX 77058 (United States); Tsai, Thomas Y.R. [National Dong Hwa University, Hualien 974, Taiwan (ROC); Ding, Fuchen [Beijing Institute of Petrochemical Technology, Daxing, Beijing 102600 (China); Ling, Hao [East China University of Science and Technology, Shanghai 200237 (China); Yui, Sok [Syncrude Research Centre, 9421-17 Avenue, Edmonton, Alberta (Canada T6N 1H4)

2006-06-15

A series of cracking tests in a comprehensive study were conducted on separate occasions involving all or parts of 10 Canadian vacuum gas oil (VGO) feeds and a catalyst. VGOs were cracked in fixed- and fluid-bed microactivity test (MAT) units, the Advanced Cracking Evaluation (ACE) unit, and a modified ARCO riser reactor. Several important observations from this study were reported, including the effects of gasoline precursors on the maximum gasoline yields and aromatics in feeds on the conversion levels at which the maximum gasoline yields occurred. Yield profiles were found to be similar in shapes and relative positions between H{sub 2}S-free dry gas and catalytic coke for all but one of the feeds. Conversion and yield data obtained from the three batch reactors were compared and discussed. At a given conversion, correlations existed among the fixed- and fluid-bed MAT units, and the ACE for each product yield. A method to check the qualities of MAT and riser data was demonstrated by plotting the coke or total gas selectivity versus the gasoline selectivity. (author)

Composite risers for deep-water offshore technology: Problems and prospects. 1. Metal-composite riser

Science.gov (United States)

Beyle, A. I.; Gustafson, C. G.; Kulakov, V. L.; Tarnopol'skii, Yu. M.

1997-09-01

Prospects for the application of advanced composites in the offshore technology of oil production are considered. The use of composites in vertical pipelines-risers seems to be the most efficient. The operating loads are studied and the attendant problems are formulated. A comparative analysis of the characteristics of metal, composite, and metal-composite deep-water risers is presented. A technique is developed for designing multilayered risers, taking into account the action of internal and external pressures, gravity, and the axial tensile force created by tensioners, as well as the residual technological stresses due to the difference in coefficients of thermal expansion, physical-chemical shrinkage, and force winding. Numerical estimations are given for a two-layered riser with an inner metal layer of steel, titanium, or aluminum alloys and a composite layer of glass- or carbon-fiber plastics formed by circumferential winding. It is shown that the technological stresses substantially affect the characteristics of the riser.

Flow Mapping in a Gas-Solid Riser via Computer Automated Radioactive Particle Tracking (CARPT)

Energy Technology Data Exchange (ETDEWEB)

Muthanna Al-Dahhan; Milorad P. Dudukovic; Satish Bhusarapu; Timothy J. O' hern; Steven Trujillo; Michael R. Prairie

2005-06-04

Statement of the Problem: Developing and disseminating a general and experimentally validated model for turbulent multiphase fluid dynamics suitable for engineering design purposes in industrial scale applications of riser reactors and pneumatic conveying, require collecting reliable data on solids trajectories, velocities ? averaged and instantaneous, solids holdup distribution and solids fluxes in the riser as a function of operating conditions. Such data are currently not available on the same system. Multiphase Fluid Dynamics Research Consortium (MFDRC) was established to address these issues on a chosen example of circulating fluidized bed (CFB) reactor, which is widely used in petroleum and chemical industry including coal combustion. This project addresses the problem of lacking reliable data to advance CFB technology. Project Objectives: The objective of this project is to advance the understanding of the solids flow pattern and mixing in a well-developed flow region of a gas-solid riser, operated at different gas flow rates and solids loading using the state-of-the-art non-intrusive measurements. This work creates an insight and reliable database for local solids fluid-dynamic quantities in a pilot-plant scale CFB, which can then be used to validate/develop phenomenological models for the riser. This study also attempts to provide benchmark data for validation of Computational Fluid Dynamic (CFD) codes and their current closures. Technical Approach: Non-Invasive Computer Automated Radioactive Particle Tracking (CARPT) technique provides complete Eulerian solids flow field (time average velocity map and various turbulence parameters such as the Reynolds stresses, turbulent kinetic energy, and eddy diffusivities). It also gives directly the Lagrangian information of solids flow and yields the true solids residence time distribution (RTD). Another radiation based technique, Computed Tomography (CT) yields detailed time averaged local holdup profiles at

Advances in riser and pipeline technologies

Energy Technology Data Exchange (ETDEWEB)

Kan, Wan C.; Mortazavi, Mehrdad; Weir, Michael S. [ExxonMobil Development Company, Dallas, TX (United States)

2009-12-19

As oil and gas production continues to move into new frontier areas, novel applications of the existing riser and pipeline technologies need to be developed to meet the often more stringent requirements encountered in these environments. The challenges include ultra deep water, harsh environments, aggressive fluid conditions, and local content objectives, etc. They will require industry to constantly extend, expand, and enhance the broad range of solution options. Also, the existing design criteria in industry may need to be revised or new criteria may need to be developed to satisfy these needs. Exxon Mobil (Em) employs, and works with others in industry to promote robust design and operating practices. This approach requires in-depth understanding, sound engineering principles, advanced analysis, uncertainty management, and supportive qualification test data. It enables confident selection, extrapolation, and innovation of technologies to address new riser system and pipeline challenges. Focus on fundamental is imperative to ensure integrity of the selected systems during fabrication, installation, and operation phases. Recent and past project experience in deep water Gulf of Mexico and West Africa provides many successful examples of this approach. This paper reviews several examples of the key riser system and pipeline technology enhancements recently achieved by EM to provide confidence in addressing technical and project application challenges. Riser system technology enhancements addressed in this paper include steel catenary riser (SCR) application on turret-moored FPSO with severe motions, pipe-in-pipe (PIP) hybrid production riser to effectively manage gas lift and flow assurance requirements, irregular wave analysis methodology for flexible risers and umbilicals to reduce conservatism, and qualification of riser and pipeline VIV prediction and mitigation methods. Pipeline technology enhancements detailed in this paper include lateral buckling prediction

Severe Slugging in Air-Water Hybrid Riser System

Directory of Open Access Journals (Sweden)

Jing Gong

2014-11-01

Full Text Available In the subsea pipeline gathering system, severe slugging flow is prone to occur. Severe slugging flow brings major threat to production and flow assurance in oil and gas industry due to periodical pressure oscillation and large liquid volume. Currently many researchers pay much more attention on L-shaped riser, catenaries, and S-shaped riser; little research has been made on hybrid riser, which is applied in the Africa West and Gulf of Mexico oil fields. Flow characteristics simulation for hybrid riser is made in this paper, using the one-dimensional and quasi-equilibrium model to simulate not only the riser-base pressure, severe slugging period, and the liquid slug length of the whole system but also base-pressure in the flexible pipe section. The calculated results match well with the experiment data. Besides, the influence of flexible pipe to the severe slugging characteristics of hybrid riser system is analyzed, which are significant for the determination of riser structure.

Le comportement mécanique des risers. Influence des principaux paramètres Mechanical Behaviour of Marine Risers Mode of Influence of Principal Parameters

Directory of Open Access Journals (Sweden)

Sparks C.

2006-11-01

Full Text Available Cet article a pour but de déterminer les principaux paramètres qui gouvernent le comportement mécanique des risers de forage et de production, et d'expliquer pourquoi et comment ils interviennent. Une compréhension claire de ces influences permet d'optimiser rapidement un riser donné sans avoir recours à un grand nombre d'analyses par ordinateur. Celui qui conçoit un riser est principalement préoccupé par les points suivants : - niveaux de contraintes dans la partie courante du riser ; - mouvements angulaires à la base du riser (ou moments, dans le cas d'une liaison rigide ; - mouvements relatifs au niveau de la liaison plate-forme/riser. La méthode utilisée dans cet article consiste à établir des expressions analytiques valables pour des risers simplifiés. Les conclusions tirées de ces expressions ont ensuite été verifiéés à l'aide d'un programme de calcul capable de simuler le comportement dynamique d'un riser dans des configurations variées. This paper attempts to identify the principal parameters, that influence the behavior of drilling and production risers and to explain how and why they do so. Clear understanding of these influences enable particular risers to be optimised rapidly without recourse to an inordinate number of computer analyses. The points of greatest concern, to the riser designer, are: a Stress levels in the main length of riser. (b Angular movement at sea bed (or moment, if the connection is rigid. (c Relative movement at riser/platform connection. The approach, used in the paper, has been ta derive analytical expressions, for simplified riser cases. Conclusions drawn from these expressions have then been checked for validity, by using a dynamic analysis computer program to simulate a wide range of cases.

Modeling Of A Fluid Catalytic Cracking (Fcc) Riser Reactor - The ...

African Journals Online (AJOL)

Journal of Modeling, Design and Management of Engineering Systems. Journal Home · ABOUT · Advanced Search · Current Issue · Archives · Journal Home > Vol 1, No 1 (2002) >. Log in or Register to get access to full text downloads.

Steel catenary risers supported by subsurface buoy

OpenAIRE

Adebayo, Addayo

2011-01-01

Master's thesis in Offshore technology Oil and gas exploration and production activities in deep and ultra deep waters in hostile environments necessitates the need to develop innovative riser systems capable of ensuring transfer of fluids from the seabed to a floating vessel and vice versa, with little or no issues with respect to influences of environmental loads and vessel motions. Over the years, studies have shown that the conventional flexible riser and steel catenary riser config...

Computational Fluid Dynamics-Discrete Element Method (CFD-DEM) Study of Mass-Transfer Mechanisms in Riser Flow.

Science.gov (United States)

Carlos Varas, Álvaro E; Peters, E A J F; Kuipers, J A M

2017-05-17

We report a computational fluid dynamics-discrete element method (CFD-DEM) simulation study on the interplay between mass transfer and a heterogeneous catalyzed chemical reaction in cocurrent gas-particle flows as encountered in risers. Slip velocity, axial gas dispersion, gas bypassing, and particle mixing phenomena have been evaluated under riser flow conditions to study the complex system behavior in detail. The most important factors are found to be directly related to particle cluster formation. Low air-to-solids flux ratios lead to more heterogeneous systems, where the cluster formation is more pronounced and mass transfer more influenced. Falling clusters can be partially circumvented by the gas phase, which therefore does not fully interact with the cluster particles, leading to poor gas-solid contact efficiencies. Cluster gas-solid contact efficiencies are quantified at several gas superficial velocities, reaction rates, and dilution factors in order to gain more insight regarding the influence of clustering phenomena on the performance of riser reactors.

Reliability analysis of wake-induced collision of flexible risers

OpenAIRE

Fu, Ping; Leira, Bernt Johan; Myrhaug, Dag

2017-01-01

Collision between risers is an important design and operational concern, especially in deep water since the probability of collision tends to increase as the riser length increases. Riser collision is due to the joint effects of many processes, i.e. environmental loads, hydrodynamic interference and surface floater motions and the most of them are stochastic processes. This paper provides an approach for estimating the failure probability of riser collision by considering these joint effects ...

FCC-ee Overview

CERN Document Server

Zimmermann, F; Benedikt, M; Burkhardt, H; Cerutti, F; Ferrari, A; Gutleber, J; Haerer, B; Holzer, B; Jensen, E; Kersevan, R; Lebrun, P; Martin, R; Mereghetti, A; Osborne, J; Papaphilippou, Y; Schulte, D; Tomas, R; Wenninger, J; Blondel, A; Koratzinos, M; Boscolo, M; Lari, L; Furukawa, K; Ohmi, K; Oide, K; White, S; Bogomyagkov, A; Koop, I; Levichev, E; Muchnoi, N; Nikitin, S; Shatilov, D; Wienands, U; Gianfelice, E; Medina, L

2015-01-01

The FCC-ee is a proposed circular e+e- collider installed in a new 100 km tunnel delivering high luminosity to four experiments at centre-of-mass energies ranging from 91 GeV (Z pole) over 160 GeV (W threshold) and 240 GeV (H production) to 350 GeV (t physics). The FCC-ee design is pursued as part of the global Future Circular Collider (FCC) study, which regards the FCC-ee as a potential intermediate step towards a 100-TeV hadron collider, called FCC-hh, sharing the same tunnel infrastructure. We here report the FCC-ee design status.

Hydrodynamics of a natural circulation loop in a scaled-down steam drum-riser-downcomer assembly

Energy Technology Data Exchange (ETDEWEB)

Basu, Dipankar N., E-mail: dnbasu@iitg.ernet.in; Patil, N.D.; Bhattacharyya, Souvik; Das, P.K.

2013-12-15

Highlights: • Experimental investigation of loop hydrodynamics in a scaled-down simulated AHWR. • Identification of flow regimes and transition analyzing conductance probe signal. • Downcomer flow maximizes with fully developed churn flow and lowest for bubbly flow. • Highest downcomer flow rate is achieved with identical air supply to both risers. • Interaction of varying flow patterns reduces downcomer flow for unequal operation. - Abstract: Complex interactions of different phases, widely varying frictional characteristics of different flow regimes and the involvement of multiple scales of transport make the modelling of a two-phase natural circulation loop (NCL) exceedingly difficult. The knowledge base about the dependency of downcomer flow rate on riser-side flow patterns, particularly for systems with multiple parallel channels is barely developed, necessitating the need for detailed experimentation. The present study focuses on developing a scaled-down test facility relevant to the Advanced Heavy Water Reactor conceived in the atomic energy programme of India to study the hydrodynamics of the NCL using air and water as test fluids. An experimental facility with two risers, one downcomer and a phase-separating drum was fabricated. Conductivity probes and photographic techniques are used to characterize the two phase flow. Normalized voltage signals obtained from the amplified output of conductivity probes and their subsequent analysis through probability distribution function reveal the presence of different two-phase flow patterns in the riser tubes. With the increase in air supply per riser void fraction in the two-phase mixture increases and gradually flow patterns transform from bubbly to fully developed annular through slug, churn and dispersed annular flow regimes. Downcomer flow rate increases rapidly with air supply till a maximum and then starts decreasing due to enhanced frictional forces. However, the maximum value of downcomer water

Natural Frequencies and Mode Shapes of Statically Deformed Inclined Risers

KAUST Repository

Alfosail, Feras

2016-10-15

We investigate numerically the linear vibrations of inclined risers using the Galerkin approach. The riser is modeled as an Euler-Bernoulli beam accounting for the nonlinear mid-plane stretching and self-weight. After solving for the initial deflection of the riser due to self-weight, we use a Galerkin expansion employing 15 axially loaded beam mode shapes to solve the eigenvalue problem of the riser around the static equilibrium configuration. This yields the riser natural frequencies and corresponding exact mode shapes for various values of inclination angles and tension. The obtained results are validated against a boundary-layer analytical solution and are found to be in good agreement. This constitutes a basis to study the nonlinear forced vibrations of inclined risers.

Prevention of pulsations caused by flexible risers

NARCIS (Netherlands)

Belfroid S.P.C; Golliard, J.; Korst, H.J.C.

2013-01-01

In the last few decades, flexible risers have increasingly been used in the offshore oil and gas industry. In gas applications these risers can generate high amplitude tonal pressure fluctuations when the gas velocity reaches a threshold value. The resulting pressure fluctuations can then cause high

1000 meters water depth rigid TLP riser; Riser rigido de plataforma de pernas atirantadas para lamina d'agua de 1000 metros

Energy Technology Data Exchange (ETDEWEB)

Braga, Mauro Jacinto Pastor

1990-07-01

A procedure to estimate the fatigue life of a TLP riser in 1000 meters water depth based on a hydro-elastic analysis of an integrated riser-TLP model in the time domain is presented . The computational architecture is shown that makes it feasible to process and store the great amount of data involved. The procedure is applied to a 1000 meters water depth TLP with a set of 40 risers 8 inches in diameter equipped with a floatation layer. (author)

Flexible riser integrity management: areas of concern and applications

Energy Technology Data Exchange (ETDEWEB)

Podskarbi, Mateusz [Schlumberger Servicos de Petroleo Ltda., Rio de Janeiro, RJ (Brazil)

2008-07-01

Flexible risers are key enables for both deep water and shallow water offshore production developments. Number of flexible risers installed worldwide is into several thousands with two main concentration areas - offshore Brazil and North Sea. Flexible risers are subject to significant loads including environmental impacts, vessel motions, internal temperature and pressure as well as substantial installation loads. Excessive loads of one type or a combination of various types of loads can cause damage to the flexible that can lead to a catastrophic failure. Industry observed number of failures increasing in recent years. Operators and manufacturing companies are taking various steps to address this issue. One of possible approaches is to use monitoring instrumentation to measure riser response and integrity in real time. This paper reviews various types of flexible riser damage mechanisms caused by impact damage, corrosion, excessive pressure, armor wire rupture, compromising flexible riser minimum bend radius, excessive fatigue loading, etc. Failure mechanisms are reviewed with particular focus on the consequences that it causes in terms of risk to the infrastructure and detectable changes. Further part of the paper is focused on monitoring techniques employed and available to detect particular types of failure mechanisms. Systematic review of the monitoring techniques is provided with specific attention given to ability of these techniques to provide early warnings of riser failure. Evaluation of monitoring techniques versus modes of operation and failure mechanism is key to selecting appropriate system that ensures effectiveness of the integrity management program. (author)

FCC 5 and FCC 6 (3/4)

CERN Multimedia

CERN. Geneva; Schulte, Daniel

2016-01-01

Abstract: The electron-positron collider, FCC-ee, should provide collisions over a wide range of beam energies, ranging from roughly 35 GeV to almost 200 GeV. The physics goals of the FCC-ee collider call for luminosities around 1e36 cm-2s-1 per interaction point at the Z pole and several 1e34 cm-2s-1 at the ZH production peak. The beam energy should be pushed above 175 GeV, with a total synchrotron-radiation power not exceeding 100 MW. The extremely high luminosities and resulting short beam lifetime, due to radiative Bhabha scattering, can be sustained by top-up injection. The FCC-ee acce...

Composite Risers for Deepwater Applications Risers composites pour applications en mer profonde

Directory of Open Access Journals (Sweden)

Metivaud G.

2006-11-01

Full Text Available This paper is devoted to the high performance composite tubes developed by the Institut Français du Pétrole (IFP and Aerospatiale for deepwater risers applications. The design principles of the tubes are first presented, along with results of preliminary work carried out as part of the initial feasibility study. Applications of composite tubes to drilling riser Kill and Choke lines and to TLP production risers, both of which have been studied in detail, are then described. Technical and operational advantages obtained from such applications are discussed. Cet article présente les travaux réalisés par l'Institut Français du Pétrole et l'Aerospatiale dans le domaine des tubes composites haute performance pour les applications aux liaisons fond-surface de forage et de production en mer profonde. Les matériaux composites avancés sont une classe de matériaux très particulière, présentant à la fois des caractéristiques mécaniques élevées et une densité spécifique faible. Ils sont utilisés principalement par les industries de l'aéronautique et de l'espace, mais l'industrie pétrolière en mer profonde est un secteur où ils peuvent trouver dans l'avenir des applications très intéressantes, notamment les tubes de risers. Les tubes de risers pétroliers en mer présentent en effet une gamme de spécifications élevées (diamètres, pression, traction, fatigue dans un environnement sévère et leur poids suspendu peut pénaliser fortement les systèmes de forage ou de production par grande profondeur d'eau. Un premier concept de tube composite haute performance a été développé par IFP et Aerospatiale au début des années 1980 ; sa partie courante, réalisée par enroulement filamentaire de fibres de verre R ou de fibres de carbone, et son système d'embout ont été soumis à une série d'essais mécaniques (pression interne jusqu'à 105 MPa, traction supérieure à 1 000 kN pour un diamètre nominal de 0,1 m, millions de

Numerical Modeling and Mechanical Analysis of Flexible Risers

Directory of Open Access Journals (Sweden)

J. Y. Li

2015-01-01

Full Text Available ABAQUS is used to create a detailed finite element model for a 10-layer unbonded flexible riser to simulate the riser’s mechanical behavior under three load conditions: tension force and internal and external pressure. It presents a technique to create detailed finite element model and to analyze flexible risers. In FEM model, all layers are modeled separately with contact interfaces; interaction between steel trips in certain layers has been considered as well. FEM model considering contact interaction, geometric nonlinearity, and friction has been employed to accurately simulate the structural behavior of riser. The model includes the main features of the riser geometry with very little simplifying assumptions. The model was solved using a fully explicit time-integration scheme implemented in a parallel environment on an eight-processor cluster and 24 G memory computer. There is a very good agreement obtained from numerical and analytical comparisons, which validates the use of numerical model here. The results from the numerical simulation show that the numerical model takes into account various details of the riser. It has been shown that the detailed finite element model can be used to predict riser’s mechanics behavior under various load cases and bound conditions.

Dynamic response of a riser under excitation of internal waves

Science.gov (United States)

Lou, Min; Yu, Chenglong; Chen, Peng

2015-12-01

In this paper, the dynamic response of a marine riser under excitation of internal waves is studied. With the linear approximation, the governing equation of internal waves is given. Based on the rigid-lid boundary condition assumption, the equation is solved by Thompson-Haskell method. Thus the velocity field of internal waves is obtained by the continuity equation. Combined with the modified Morison formula, using finite element method, the motion equation of riser is solved in time domain with Newmark-β method. The computation programs are compiled to solve the differential equations in time domain. Then we get the numerical results, including riser displacement and transfiguration. It is observed that the internal wave will result in circular shear flow, and the first two modes have a dominant effect on dynamic response of the marine riser. In the high mode, the response diminishes rapidly. In different modes of internal waves, the deformation of riser has different shapes, and the location of maximum displacement shifts. Studies on wave parameters indicate that the wave amplitude plays a considerable role in response displacement of riser, while the wave frequency contributes little. Nevertheless, the internal waves of high wave frequency will lead to a high-frequency oscillation of riser; it possibly gives rise to fatigue crack extension and partial fatigue failure.

How to inspect platform risers: an effective approach and new challenges

International Nuclear Information System (INIS)

Agthoven, Robert van

2007-01-01

Ageing risers on offshore platforms, designed and built several decades ago, were until recently hard to inspect or not inspectable at all. This was due to their layout or ID geometry changes prohibiting the use of product propelled intelligent pigs, which are frequently used, on long distance pipelines. Growing concerns about reliability and safety, as well as environmental pressure, are the impetus for operators of offshore platforms to check the condition of the risers, which until now could not be inspected. This paper describes a few solutions to enter these 'non-inspect-able' risers to check their condition by using special small diameter cable operated tools. These new miniature cable tools are spin-offs from the well-known cable (tether, umbilical) tools introduced more than two decades ago by RTD for the inspection of (off)-loading lines. The first generation gravity driven small diameter riser inspection tools were designed to inspect the vertical section of the riser only. On-going development has resulted in a second generation of riser inspection tools which can now enter a few hundred metres into the horizontal connecting pipeline on the sea-floor by using a small, but powerful, crawler. With this ability these tools are the only solution for riser-pipes and relatively short connecting pipelines which terminate at a T-or Y-connection in the vicinity of the platform. All riser inspection tools apply ultrasonics to quantify wall thickness and corrosion. A novel TOFD (Time Of Flight Diffraction) module can be applied as an option to inspect in the circumferential weld area. All cable tools have a reinforced cable, which is used for tool control and retrieval. A strong advantage of these cable tools is that they provide on-line results and allow on-site evaluation. Since the introduction of these new tools considerable experience has been gained. The history of development and several typical cases of applications are given in this paper. In addition

Evaluation of riser 14 temperature response

International Nuclear Information System (INIS)

OGDEN, D.M.

1999-01-01

The initial sluicing activities of Project WRSS resulted in a two month increase in temperatures as measured by the Riser 14 thermocouple tree of tank 241-C-106. While this increase was anticipated, the maximum temperature was higher than expected. An evaluation was performed to determine if adequate subcooling exists in the waste to continue sluicing activities. It was determined that a minimum of 10 F subcooling exists in the waste and that the higher Riser 14 temperatures were the result of higher than assumed waste saturation temperature

Attrition Resistant Fischer-Tropsch Catalysts Based on FCC Supports

Energy Technology Data Exchange (ETDEWEB)

Adeyiga, Adeyinka

2010-02-05

Commercial spent fluid catalytic cracking (FCC) catalysts provided by Engelhard and Albemarle were used as supports for Fe-based catalysts with the goal of improving the attrition resistance of typical F-T catalysts. Catalysts with the Ruhrchemie composition (100 Fe/5 Cu/4.2 K/25 spent FCC on mass basis) were prepared by wet impregnation. XRD and XANES analysis showed the presence of Fe{sub 2}O{sub 3} in calcined catalysts. FeC{sub x} and Fe{sub 3}O{sub 4} were present in the activated catalysts. The metal composition of the catalysts was analyzed by ICP-MS. F-T activity of the catalysts activated in situ in CO at the same conditions as used prior to the attrition tests was measured using a fixed bed reactor at T = 573 K, P = 1.38 MPa and H{sub 2}:CO ratio of 0.67. Cu and K promoted Fe supported over Engelhard provided spent FCC catalyst shows relatively good attrition resistance (8.2 wt% fines lost), high CO conversion (81%) and C{sub 5}+ hydrocarbons selectivity (18.3%).

Thermal-hydraulic study of fixed bed nuclear reactor (FBNR), in FCC, BCC and pseudo-random configurations of the core through CFD method

International Nuclear Information System (INIS)

Luna, M.; Chavez, I.; Cajas, D.; Santos, R.

2015-01-01

The study of thermal-hydraulic performance of a fixed bed nuclear reactor (FBNR) core and the effect of the porosity was studied by the CFD method with 'SolidWorks' software. The representative sections of three different packed beds arrangements were analyzed: face-centered cubic (FCC), body-centered cubic (BCC), and a pseudo-random, with values of porosity of 0.28, 0.33 and 0.53 respectively. The minimum coolant flow required to avoid the phase change for each one of the configurations was determined. The results show that the heat transfer rate increases when the porosity value decreases, and consequently the minimum coolant flow in each configuration. The results of minimum coolant flow were: 728.51 kg/s for the FCC structure, 372.72 kg/s for the BCC, and 304.96 kg/s for the pseudo-random. Meanwhile, the heat transfer coefficients in each packed bed were 6480 W/m 2 *K, 3718 W/m 2 *K and 3042 W/m 2 *K respectively. Finally the pressure drop was calculated, and the results were 0.588 MPa for FCC configuration, 0.033 MPa for BCC and 0.017 MPa for the pseudo-random one. This means that with a higher porosity, the fluid can circulate easier because there are fewer obstacles to cross, so there are fewer energy losses. (authors)

Preliminary optimal configuration on free standing hybrid riser

Directory of Open Access Journals (Sweden)

Kyoung-Su Kim

2018-05-01

Full Text Available Free Standing Hybrid Riser (FSHR is comprised of vertical steel risers and Flexible Jumpers (FJ. They are jointly connected to a submerged Buoyancy Can (BC. There are several factors that have influence on the behavior of FSHR such as the span distance between an offshore platform and a foundation, BC up-lift force, BC submerged location and FJ length.An optimization method through a parametric study is presented. Firstly, descriptions for the overall arrangement and characteristics of FSHR are introduced. Secondly, a flowchart for optimization of FSHR is suggested. Following that, it is described how to select reasonable ranges for a parametric study and determine each of optimal configuration options. Lastly, numerical analysis based on this procedure is performed through a case study. In conclusion, the relation among those parameters is analyzed and non-dimensional parametric ranges on optimal arrangements are suggested. Additionally, strength analysis is performed with variation in the configuration. Keywords: Free standing hybrid riser, Hybrid riser system, Buoyancy can, Flexible jumper, Deepwater, Multi-body dynamics

Features of a time domain simulation tool for rigid riser design

Energy Technology Data Exchange (ETDEWEB)

Morooka, Celso K.; Brandt, Dustin M. [Universidade Estadual de Campinas (UNICAMP), SP (Brazil). Faculdade de Engenharia Mecanica. Dept. de Engenharia de Petroleo; Matt, Cyntia G.C.; Franciss, Ricardo [PETROBRAS S.A., Rio de Janeiro, RJ (Brazil). Centro de Pesquisas

2008-07-01

This paper present a number of numerical implementations designed for the analysis of rigid riser's static and dynamic behavior that includes the effects of vortex induced vibrations (VIV) and marine hydrodynamic loads in time domain. Features include the ability to consider pipe with a free-span utilizing a soil/riser interaction model. An implementation of a numerical coupling scheme to couple the vertical riser and platform dynamics was developed to allow prediction of the sub sea Blow-Out Preventer (BOP) re-entry into a sub sea petroleum well when drilling different phases of deep and ultra-deep wells. The developments contains support for the consideration of the Self Standing Hybrid Riser (SSHR) configuration which has been shown to be a promising riser configuration in deep and ultra-deep waters. A graphical interface was also created to better grasp the results and aid in the modeling, processing and to help analyze the numerical simulations, contributing to enhance agility and quality of the riser design and analysis processes. (author)

CFD Simulation of Vortex Induced Vibration for FRP Composite Riser with Different Modeling Methods

Directory of Open Access Journals (Sweden)

Chunguang Wang

2018-04-01

Full Text Available Steel risers are widely used in offshore oil and gas industry. However, the production capacity and depths are limited due to their extreme weight and poor fatigue and corrosion resistance. Nowadays, it is confirmed that fiber reinforced polymer (FRP composite risers have apparent advantages over steel risers. However, the study of vortex induced vibration (VIV for composite risers is rarely involved. Three different risers (one steel riser and two composite risers were compared for their VIV characteristics. The effects of 2D and 3D models and fluid–structure interaction (FSI were considered. The models of composite risers are established by effective modulus method (EMM and layered-structure method (LSM. It is found that 2D model are only suitable for ideal condition, while, for real situation, 3D model with FSI has to be considered. The results show that the displacements of the FRP composite risers are significantly larger than those of the steel riser, while the stresses are reversed. In addition, the distributions of the displacements and stresses depend on the geometries, material properties, top-tension force, constraints, etc. In addition, it is obvious that EMM are suitable to study the global working condition while LSM can be utilized to obtain the results in every single composite layer.

Response prediction of long flexible risers subject to forced harmonic vibration

OpenAIRE

Riveros, Carlos Alberto; Utsunomiya, Tomoaki; Maeda, Katsuya; Itoh, Kazuaki

2010-01-01

Several research efforts have been directed toward the development of models for response prediction of flexible risers. The main difficulties arise from the fact that the dynamic response of flexible risers involves highly nonlinear behavior and a self-regulated process. This article presents a quasi-steady approach for response prediction of oscillating flexible risers. Amplitude-dependent lift coefficients are considered, as is an increased mean drag coefficient model during synchronizatio...

Engineering study - installation of new risers in Single-Shell Tanks

International Nuclear Information System (INIS)

Magruder, W.J.

1994-08-01

A sampling program is being developed to characterize the 149 underground SSTs on the Hanford Site. The sampling effort will require access to the tank interior in a minimum of two locations per tank. Some of the risers suitable for sampling are either unavailable or are not in locations for proper characterization of the tank contents. Additional risers will be required in the SSTs to support the tank characterization sampling program. The purpose of this engineering study is to review alternatives for installation of new riser in the SSTs

Pressured drilling riser design for drilling in ultra deep water with surface bop

Energy Technology Data Exchange (ETDEWEB)

Zhang, J.; Morrison, D.; Efthymiou, M.; Lo, K.H. [Shell Global Solutions, 78 - Velizy Villacoublay (France); Magne, E.; Leach, C. [Shell Internationale Exploration and Production (Netherlands)

2002-12-01

In conventional drilling with a semi-submersible rig valuable rig time is used to run and retrieve the BOP and its accessories on the seabed, and this time increases with water depth. Furthermore, use of the conventional sub-sea BOP requires a large-diameter riser, which requires substantial rig storage and deck load capacity prior to installation. It also requires high riser-tensioning capacity or additional buoyancy. Thus as the water depth increases, it leads to a need for heavy duty 4. and 5. generation rigs with escalation in costs. The high cost of deep-water drill rigs is leading to the development of Surface BOP technology. In this development, the BOP is placed above sea level and the riser is simply a continuation of the casing (typical diameter 13-3/8''). This eliminates the need for a heavy 21'' riser and for running the BOP to the sea bed and retrieving it. Moreover, the reduced tension requirement for the smaller riser extends the water depth capability of 3. generation drilling semi-submersibles, enabling them to drill in deeper waters. A critical success factor for this development is the ability to design the riser/casing to withstand high internal pressures due to well kicks, in addition to environmental loads, and to restrict vessel offsets within certain limits so as not to overload the riser under the prevailing weather conditions. This paper addresses the design considerations of a pressured drilling riser that can be used with a surface BOP in deep-water. Key design issues that are sensitive to ultra-deep-water applications are discussed. The technical aspects of using (disposable) standard casing with threaded connector for the drilling riser are discussed, with a particular emphasis on the connector fatigue-testing program to quantify the stress concentration factor for fatigue design. Emerging composite material offers some alternatives to the steel riser when drilling in ultra-deep water Design issues related to the

A case study on riser analysis of a drilling riser in deep waters; Estudo de caso: analises estruturais e hidrodinamicas de um riser de perfuracao em aguas profundas

Energy Technology Data Exchange (ETDEWEB)

Roveri, Francisco E.; Pestana, Rafael G. [PETROBRAS S.A., Rio de Janeiro, RJ (Brazil). Centro de Pesquisas

2008-07-01

This paper presents a set of structural and hydrodynamic analyses of a connected marine riser, in 1900 meter water depth. Operating windows are determined for one year return period environmental conditions and for a set of drilling fluid weight density values. Parametric analyses are carried out to study the riser response sensitivity to variations in environmental conditions, drilling fluid weight density, upper and lower flex joint rotational stiffness and vessel motion phase angles. Current, drilling fluid weight density and vessel motion phase angle changes affect significantly the system response, whereas the response is not significantly affected by changes in wave height, wave period and flex joint rotational stiffness. (author)

Development of a 14-inch ID High-Pressure Hybrid Riser for SBOP Drilling Développement d’un riser hybride 14”ID haute pression pour le forage SBOP

Directory of Open Access Journals (Sweden)

Persent E.

2009-11-01

Full Text Available This paper discusses the development of a 14-inch ID high-pressure hybrid riser (10 000 psi for surface BOP drilling in ultra-deep water (10 000 ft. The high-pressure hybrid riser system is obtained by adapting and combining two existing technologies, previously developed by the IFP for other applications: – the Clip connector, a double breech-block type connector to provide a quick and safe connection for riser joints; – hybrid pipe technology, a steel pipe hoop-wound with tapes of carbon fibers impregnated with polyamide thermoplastic resin. IFP has developed a new 14-inch ID HP Clip connector for the hybrid riser application. The connector is capable of withstanding a 2.8 million pound tension and a 10 000 psi operating pressure. In addition, a 16-inch nominal OD hybrid riser pipe has been designed to replace the steel riser pipe with a thinnerwalled hoop-wound steel pipe. The significant weight savings that can be achieved with the hybrid riser pipe make it possible to design an effective riser architecture to withstand the high pressure and deep water requirements. Pursuant to design studies, a 14-inch ID prototype assembly consisting of two hybrid riser pipe sections with a high-pressure Clip connector was manufactured. A test program, including burst and collapse tests as well as cyclic fatigue testing, was formulated and carried out to qualify the performance of the Clip connector and hybrid riser pipe system. Completion of hybrid pipe additional fatigue testing and realization of a scale-one field testing of the hybrid riser are considered as the next steps of the project. To date, the main test results (burst, collapse, fatigue resistance confirm that the Clip connector and the hybrid pipe technologies are well suited for ultra-deep sea drilling with a surface BOP. However, the fatigue resistance of hybrid riser pipes still needs to be better characterized. Cet article présente le développement d’un riser hybride 14”ID haute

Uncertainty evaluation of fluid dynamic models and validation by gamma ray transmission measurements of the catalyst flow in a FCC cold pilot unity

International Nuclear Information System (INIS)

Teles, Francisco A.S.; Santos, Ebenezer F.; Dantas, Carlos C.; Melo, Silvio B.; Santos, Valdemir A. dos; Lima, Emerson A.O.

2013-01-01

In this paper, fluid dynamics of Fluid Catalytic Cracking (FCC) process is investigated by means of a Cold Flow Pilot Unit (CFPU) constructed in Plexiglas to visualize operational conditions. Axial and radial catalyst profiles were measured by gamma ray transmission in the riser of the CFPU. Standard uncertainty was evaluated in volumetric solid fraction measurements for several concentrations at a given point of axial profile. Monitoring of the pressure drop in riser shows a good agreement with measured standard uncertainty data. A further evaluation of the combined uncertainty was applied to volumetric solid fraction equation using gamma transmission data. Limit condition of catalyst concentration in riser was defined and simulation with random numbers provided by MATLAB software has tested uncertainty evaluation. The Guide to the expression of Uncertainty in Measurement (GUM) is based on the law of propagation of uncertainty and on the characterization of the quantities measured by means of either a Gaussian distribution or a t-distribution, which allows measurement uncertainty to be delimited by means of a confidence interval. A variety of supplements to GUM are being developed, which will progressively enter into effect. The first of these supplements [3] describes an alternative procedure for the calculation of uncertainties: the Monte Carlo Method (MCM).MCM is an alternative to GUM, since it performs a characterization of the quantities measured based on the random sampling of the probability distribution functions. This paper also explains the basic implementation of the MCM method in MATLAB. (author)

Uncertainty evaluation of fluid dynamic models and validation by gamma ray transmission measurements of the catalyst flow in a FCC cold pilot unity

Energy Technology Data Exchange (ETDEWEB)

Teles, Francisco A.S.; Santos, Ebenezer F.; Dantas, Carlos C., E-mail: francisco.teles@ufpe.br [Universidade Federal de Pernambuco (UFPE), Recife, PE (Brazil). Centro de Tecnologia e Geociencias. Departamento de Energia Nuclear; Melo, Silvio B., E-mail: sbm@cin.ufpe.br [Universidade Federal de Pernambuco (CIN/UFPE), Recife, PE (Brazil). Centro de Informatica; Santos, Valdemir A. dos, E-mail: vas@unicap.br [Universidade Catolica de Pernambuco (UNICAP), Recife, PE (Brazil). Dept. de Quimica; Lima, Emerson A.O., E-mail: emathematics@gmail.com [Universidade de Pernambuco (POLI/UPE), Recife, PE (Brazil). Escola Politecnica

2013-07-01

In this paper, fluid dynamics of Fluid Catalytic Cracking (FCC) process is investigated by means of a Cold Flow Pilot Unit (CFPU) constructed in Plexiglas to visualize operational conditions. Axial and radial catalyst profiles were measured by gamma ray transmission in the riser of the CFPU. Standard uncertainty was evaluated in volumetric solid fraction measurements for several concentrations at a given point of axial profile. Monitoring of the pressure drop in riser shows a good agreement with measured standard uncertainty data. A further evaluation of the combined uncertainty was applied to volumetric solid fraction equation using gamma transmission data. Limit condition of catalyst concentration in riser was defined and simulation with random numbers provided by MATLAB software has tested uncertainty evaluation. The Guide to the expression of Uncertainty in Measurement (GUM) is based on the law of propagation of uncertainty and on the characterization of the quantities measured by means of either a Gaussian distribution or a t-distribution, which allows measurement uncertainty to be delimited by means of a confidence interval. A variety of supplements to GUM are being developed, which will progressively enter into effect. The first of these supplements [3] describes an alternative procedure for the calculation of uncertainties: the Monte Carlo Method (MCM).MCM is an alternative to GUM, since it performs a characterization of the quantities measured based on the random sampling of the probability distribution functions. This paper also explains the basic implementation of the MCM method in MATLAB. (author)

Academic Training Lectures | FCC | 2-5 February

CERN Multimedia

2016-01-01

Please note that the next series of Academic Training Lectures will take place from 2 to 5 February 2016.   Tuesday, 2 February 2016 from 10.30 a.m. to 12.30 p.m. in the Filtration Plant (Building 222-R-001) FCC 1: Introduction to FCC by Michael Benedikt FCC 2: FCC Physics - Challenges and Potentials by Christophe Grojean, Michelangelo Mangano https://indico.cern.ch/event/472105/   Wednesday, 3 February 2016 from 10.30 a.m. to 12.30 p.m in the Filtration Plant (Building 222-R-001) FCC 3: FCC hh Detectors and Experiments by Werner Riegler FCC 4: Experimental Measurements and Detectors for the FCC-ee by Mogens Dam https://indico.cern.ch/event/472106/   Thursday, 4 February 2016 from 10.30 a.m. to 12.30 p.m in the Filtration Plant (Building 222-R-001) FCC 5: FCC Hadron Collider Design by Daniel Schulte FCC 6: FCC Lepton Collider Design by Frank Zimmermann https://indico...

Riser equipment decontamination engineering task plan

International Nuclear Information System (INIS)

BOGER, R.M.

1999-01-01

On October 15, 1998, two Characterization Project Operations (CPO) employees were found to have contaminated clothing. An operator had 300,000-dpm/100cm2 beta/gamma, no alpha, contamination on his coat sleeve and a Radiation Control Technician (RCT) had 10,000 dpm/100cm2 beta/gamma, no alpha, on his shirt sleeve. The CPO swing shift crew was working in TX tank farm, performing sampling activities at 241-TX-113. TX tank farm is a ''clean farm'' and does not require anti-contamination clothing for entry. The CPO personnel were dressed in normal work clothes. An operator and an RCT were performing a pre-job survey that involved removing bagging around the riser equipment. When the RCT saw that the contamination readings from smear samples of the riser equipment were greater than expected, the job was suspended. Crew members were then directed to areas of lower background radiation for personnel surveys. During personnel surveys, reportable contamination was found on the coat sleeve of the operator who had been involved in the pre-job survey and on the shirt sleeve of the RCT who had been involved in the pre-job survey. No other personnel were found to be contaminated. Because of this off normal event Characterization Engineering was given the following corrective action: Examine the process methodology used for core sampling operations to determine practicality and potential long-term advantages of reducing personnel contact with contaminated equipment. This Engineering Task Plan ensures that LMHC 1998a, Corrective Action No.7 is completely addressed by Characterization Engineering. The deliverable is an Engineering Study that evaluates decontamination of riser equipment components and considers additional engineered features to reduce potential exposure to workers operating the riser equipment. This engineering study shall also address any released design features that have failed to be implemented

Development and characterization of composite materials for production of composite risers by filament winding

Energy Technology Data Exchange (ETDEWEB)

Sobrinho, L.L.; Bastian, F.L. [Federal University of Rio de Janeiro, RJ (Brazil). Dept. of Metallurgical and Materials Engineering], e-mail: ledjane@metalmat.ufrj.br; Calado, V.M.A. [Federal University of Rio de Janeiro, RJ (Brazil). Escola de Quimica

2008-07-01

Industry has been challenged to provide riser systems which are more cost effective and which can fill the technology gaps with respect to water depth, riser diameter and high temperatures left open by flexible, steel catenary risers (SCRs) and hybrid risers. Composite materials present advantages over conventional steel risers because composite materials are lighter, more fatigue and corrosion resistant, better thermal insulators and can be designed for improving the structural and mechanical response. Besides, composite materials present some attractive attributes for the offshore service, such as: high specific strength and stiffness. This paper focuses on the development and characterization of a polymer matrix (epoxy) and of material composite (epoxy/fiber glass), which will be used in a development for composites risers by the filament winding process (wet winding). (author)

Fuel cycle costs for molten-salt reactors

International Nuclear Information System (INIS)

Nagashima, Kikusaburo

1983-01-01

This report describes FCC (fuel cycle cost) estimates for MSCR (molten-salt converter reactor) and MSBR (molten-salt breeder reactor) compared with those for LWRs (PWR and BWR). The calculation is based on the present worth technique with a given discount rate for each cost item, which enables us to make comparison between FCC's for MSCR, MSBR and LWRs. As far as the computational results obtained here are concerned, shown that the FCC's for MSCR and MSBR are 70 -- 60 % lower than the values for LWRs. And it could be said that the FCC for MSCR (Pu-converter) is about 10 % lower than that for MSBR, because of the smaller amount of fissile inventory of MSCR than the inventory of MSBR. (author)

Numerical Modeling and Mechanical Analysis of Flexible Risers

OpenAIRE

Li, J. Y.; Qiu, Z. X.; Ju, J. S.

2015-01-01

ABAQUS is used to create a detailed finite element model for a 10-layer unbonded flexible riser to simulate the riser’s mechanical behavior under three load conditions: tension force and internal and external pressure. It presents a technique to create detailed finite element model and to analyze flexible risers. In FEM model, all layers are modeled separately with contact interfaces; interaction between steel trips in certain layers has been considered as well. FEM model considering contact ...

Simplified Model for Evaluation of VIV-induced Fatigue Damage of Deepwater Marine Risers

Institute of Scientific and Technical Information of China (English)

XUE Hong-xiang; TANG Wen-yong; ZHANG Sheng-kun

2009-01-01

A simplified empirical model for fatigue analysis of deepwater marine risers due to vortex-induced vibration (VIV) in non-uniform current is presented. A simplified modal vibration equation is employed according to the characteristics of deepwater top tensioned risers. The response amplitude of each mode is determined by a balance between the energy feeding into the riser over the lock-in regions and the energy dissipated by the fluid damping over the remainder based on the data from self-excited oscillation and forced oscillation experiments of rigid cylinders. Multi-modal VIV fatigue loading is obtained by the square root of the sum of squares approach.Compared with previous works, this model can take fully account of the main intrinsic natures of VIV for low mass ratio structures on lock-in regions, added mass and nonlinear fluid damping. In addition, a closed form solution of fatigue damage is presented for the case of a riser with uniform mass and cross-section oscillating in a uniform flow. Fatigue analysis of a typical deepwater riser operating in Gulf of Mexico and West Africa shows that the current velocity profiles affect the riser's fatigue life significantly and the most dangerous locations of the riser are also pointed out.

A state space approach for the eigenvalue problem of marine risers

KAUST Repository

Alfosail, Feras; Nayfeh, Ali H.; Younis, Mohammad I.

2017-01-01

A numerical state-space approach is proposed to examine the natural frequencies and critical buckling limits of marine risers. A large axial tension in the riser model causes numerical limitations. These limitations are overcome by using

Girassol, Riser Towers for ultra deep water

Energy Technology Data Exchange (ETDEWEB)

Rougier, Regis

1999-07-01

This is a brief presentation of the technical concept developed by ALTO MAR GIRASSOL (AMG) for the Girassol umbilical and flowlines system. In 1998 AMG was awarded a contract by Elf Exploration Angola for the engineering, procurement, construction and installation (EPCI) of the umbilical and flowline system. The technical concept is based around the use of sealine bundles and self-supporting hybrid riser towers which carry the production, water injection, gas injection, gas lift and service lines. The items discussed are: (1) selected field layout, (2) seabed flowlines, hybrid riser system, umbilicals, export lines, installation plan and overall project schedule.

Identifying and evaluating high risk areas and challenges on marine drilling riser system in relation to deepwater problems

OpenAIRE

Iversen, Alexander

2012-01-01

Master's thesis in Offshore technology The main concerns during drilling operations are riser integrity and maintaining well control. This thesis has mainly been focusing on the problems and challenges faced with the marine riser system to illuminate high risk areas related to riser integrity. A marine riser system consists generally of four main elements; the upper marine riser package, riser joints, lower marine riser package, and the blowout preventer, each playing an important par...

Flexible riser global analysis for very shallow water

OpenAIRE

Karegar, Sadjad

2013-01-01

Master's thesis in Offshore technology Flexible risers are widely used for a range of water depths and can accommodate large floater motions when using a buoyant system. A wide range of buoyancy solutions have been developed for very shallow water (e.g. 30-50 m), shallow water (e.g. 90-110 m) and semi-deep water (e.g. 300-400 m) and in the ranges between these depths. Flexible risers can have different configurations. These different solutions have different characteristics which influe...

Damage localization of marine risers using time series of vibration signals

Science.gov (United States)

Liu, Hao; Yang, Hezhen; Liu, Fushun

2014-10-01

Based on dynamic response signals a damage detection algorithm is developed for marine risers. Damage detection methods based on numerous modal properties have encountered issues in the researches in offshore oil community. For example, significant increase in structure mass due to marine plant/animal growth and changes in modal properties by equipment noise are not the result of damage for riser structures. In an attempt to eliminate the need to determine modal parameters, a data-based method is developed. The implementation of the method requires that vibration data are first standardized to remove the influence of different loading conditions and the autoregressive moving average (ARMA) model is used to fit vibration response signals. In addition, a damage feature factor is introduced based on the autoregressive (AR) parameters. After that, the Euclidean distance between ARMA models is subtracted as a damage indicator for damage detection and localization and a top tensioned riser simulation model with different damage scenarios is analyzed using the proposed method with dynamic acceleration responses of a marine riser as sensor data. Finally, the influence of measured noise is analyzed. According to the damage localization results, the proposed method provides accurate damage locations of risers and is robust to overcome noise effect.

Monitoring system of depressurization valves of migrated gas in annular space of flexible risers

Energy Technology Data Exchange (ETDEWEB)

Mesquita, Luiz A.; Santos, Joilson M.; Carvalho, Antonio L.; Loureiro, Patricia [PETROBRAS S.A., Rio de Janeiro, RJ (Brazil)

2005-07-01

PETROBRAS Research and Development Center - CENPES developed an automatic system for monitoring pressure of annular space due to permeation of gas in flexible risers to inspect continuously integrity of such lines. To help maintaining physical integrity of flexible risers, two PSV's are installed to end fittings on top of riser, so that operation of any valve grants the maximum admissible gas pressure within the riser annular space, as overpressure might cause damages to external polymeric layer of flexible riser. Due to the fact that there is no mechanism allowing operation to verify correct PSV performance and frequency of valve's closings and openings, we felt to be necessary the development and implement an automatic instrumented system, integrated to platform's automation and control infrastructure. The objective of this instrumentation is to monitor and register pressure of annular space in flexible riser, as well as XV's depressurization frequency. Having such information registered and monitored, can infer some riser structural conditions, anticipating repairs and preventive maintenance. In this paper we present developed system details including instruments required, application, operation of associated screens that are used in the ECOS, with events, alarms and industrial automation services required (Application development and system integration). (author)

Riser equipment decontamination engineering task plan; TOPICAL

International Nuclear Information System (INIS)

BOGER, R.M.

1999-01-01

On October 15, 1998, two Characterization Project Operations (CPO) employees were found to have contaminated clothing. An operator had 300,000-dpm/100cm2 beta/gamma, no alpha, contamination on his coat sleeve and a Radiation Control Technician (RCT) had 10,000 dpm/100cm2 beta/gamma, no alpha, on his shirt sleeve. The CPO swing shift crew was working in TX tank farm, performing sampling activities at 241-TX-113. TX tank farm is a ''clean farm'' and does not require anti-contamination clothing for entry. The CPO personnel were dressed in normal work clothes. An operator and an RCT were performing a pre-job survey that involved removing bagging around the riser equipment. When the RCT saw that the contamination readings from smear samples of the riser equipment were greater than expected, the job was suspended. Crew members were then directed to areas of lower background radiation for personnel surveys. During personnel surveys, reportable contamination was found on the coat sleeve of the operator who had been involved in the pre-job survey and on the shirt sleeve of the RCT who had been involved in the pre-job survey. No other personnel were found to be contaminated. Because of this off normal event Characterization Engineering was given the following corrective action: Examine the process methodology used for core sampling operations to determine practicality and potential long-term advantages of reducing personnel contact with contaminated equipment. This Engineering Task Plan ensures that LMHC 1998a, Corrective Action No.7 is completely addressed by Characterization Engineering. The deliverable is an Engineering Study that evaluates decontamination of riser equipment components and considers additional engineered features to reduce potential exposure to workers operating the riser equipment. This engineering study shall also address any released design features that have failed to be implemented

An efficient structural finite element for inextensible flexible risers

Science.gov (United States)

Papathanasiou, T. K.; Markolefas, S.; Khazaeinejad, P.; Bahai, H.

2017-12-01

A core part of all numerical models used for flexible riser analysis is the structural component representing the main body of the riser as a slender beam. Loads acting on this structural element are self-weight, buoyant and hydrodynamic forces, internal pressure and others. A structural finite element for an inextensible riser with a point-wise enforcement of the inextensibility constrain is presented. In particular, the inextensibility constraint is applied only at the nodes of the meshed arc length parameter. Among the virtues of the proposed approach is the flexibility in the application of boundary conditions and the easy incorporation of dissipative forces. Several attributes of the proposed finite element scheme are analysed and computation times for the solution of some simplified examples are discussed. Future developments aim at the appropriate implementation of material and geometric parameters for the beam model, i.e. flexural and torsional rigidity.

OTEC riser cable model and prototype testing

Science.gov (United States)

Kurt, J. P.; Schultz, J. A.; Roblee, L. H. S.

1981-12-01

Two different OTEC riser cables have been developed to span the distance between a floating OTEC power plant and the ocean floor. The major design concerns for a riser cable in the dynamic OTEC environment are fatigue, corrosion, and electrical/mechanical aging of the cable components. The basic properties of the cable materials were studied through tests on model cables and on samples of cable materials. Full-scale prototype cables were manufactured and were tested to measure their electrical and mechanical properties and performance. The full-scale testing was culminated by the electrical/mechanical fatigue test, which exposes full-scale cables to simultaneous tension, bending and electrical loads, all in a natural seawater environment.

Engineering Task Plan for simulated riser installation by use of rotary drilling

International Nuclear Information System (INIS)

Barnes, G.A.

1995-12-01

This task is being performed to demonstrate the feasibility of the best riser installation alternative identified in the Engineering Study. This Engineering Task Plan (ETP) will be the WHC project management plan for the riser installation demonstration activities

Magnetic non-destructive evaluation of ruptures of tensile armor in oil risers

International Nuclear Information System (INIS)

Pérez-Benitez, J A; Padovese, L R

2012-01-01

Risers are flexible multilayered pipes formed by an inner flexible metal structure surrounded by polymer layers and spiral wound steel ligaments, also known as armor wires. Since these risers are used to link subsea pipelines to floating oil and gas production installations, and their failure could produce catastrophic consequences, some methods have been proposed to monitor the armor integrity. However, until now there is no practical method that allows the automatic non-destructive detection of individual armor wire rupture. In this work we show a method using magnetic Barkhausen noise that has shown high efficiency in the detection of armor wire rupture. The results are examined under the cyclic and static load conditions of the riser. This work also analyzes the theory behind the singular dependence of the magnetic Barkhausen noise on the applied tension in riser armor wires. (paper)

An analytic solution of the static problem of inclined risers conveying fluid

KAUST Repository

Alfosail, Feras; Nayfeh, Ali H.; Younis, Mohammad I.

2016-01-01

We use the method of matched asymptotic expansion to develop an analytic solution to the static problem of clamped–clamped inclined risers conveying fluid. The inclined riser is modeled as an Euler–Bernoulli beam taking into account its self

Biodegradation of 2,4,6-trichlorophenol in a packed-bed biofilm reactor equipped with an internal net draft tube riser for aeration and liquid circulation

Energy Technology Data Exchange (ETDEWEB)

Gomez-De Jesus, A.; Romano-Baez, F.J.; Leyva-Amezcua, L.; Juarez-Ramirez, C.; Ruiz-Ordaz, N. [Departamento de Ingenieria Bioquimica, Escuela Nacional de Ciencias Biologicas, IPN. Prol. Carpio y Plan de Ayala, Colonia Santo Tomas, s/n. CP 11340, Mexico, D.F. (Mexico); Galindez-Mayer, J. [Departamento de Ingenieria Bioquimica, Escuela Nacional de Ciencias Biologicas, IPN. Prol. Carpio y Plan de Ayala, Colonia Santo Tomas, s/n. CP 11340, Mexico, D.F. (Mexico)], E-mail: cmayer@encb.ipn.mx

2009-01-30

For the aerobic biodegradation of the fungicide and defoliant 2,4,6-trichlorophenol (2,4,6-TCP), a bench-scale packed-bed bioreactor equipped with a net draft tube riser for liquid circulation and oxygenation (PB-ALR) was constructed. To obtain a high packed-bed volume relative to the whole bioreactor volume, a high A{sub D}/A{sub R} ratio was used. Reactor's downcomer was packed with a porous support of volcanic stone fragments. PB-ALR hydrodynamics and oxygen mass transfer behavior was evaluated and compared to the observed behavior of the unpacked reactor operating as an internal airlift reactor (ALR). Overall gas holdup values {epsilon}{sub G}, and zonal oxygen mass transfer coefficients determined at various airflow rates in the PB-ALR, were higher than those obtained with the ALR. When comparing mixing time values obtained in both cases, a slight increment in mixing time was observed when reactor was operated as a PB-ALR. By using a mixed microbial community, the biofilm reactor was used to evaluate the aerobic biodegradation of 2,4,6-TCP. Three bacterial strains identified as Burkholderia sp., Burkholderia kururiensis and Stenotrophomonas sp. constituted the microbial consortium able to cometabolically degrade the 2,4,6-TCP, using phenol as primary substrate. This consortium removed 100% of phenol and near 99% of 2,4,6-TCP. Mineralization and dehalogenation of 2,4,6-TCP was evidenced by high COD removal efficiencies ({approx}95%), and by the stoichiometric release of chloride ions from the halogenated compound ({approx}80%). Finally, it was observed that the microbial consortium was also capable to metabolize 2,4,6-TCP without phenol as primary substrate, with high removal efficiencies (near 100% for 2,4,6-TCP, 92% for COD and 88% for chloride ions)

Most recent developments for monitoring and controlling the annulus conditions of Marlim-Sul flexible risers

Energy Technology Data Exchange (ETDEWEB)

Rabelo, Alexandre S.; Motta, Antonio; Romero, Antonio; Nunes, Joao P.; Zaganelli Junior, Jose L.; Brack, Marcelo [PETROBRAS, Rio de Janeiro, RJ (Brazil)

2009-07-01

The main objective of this paper is to present the recent developments for monitoring and controlling the annulus conditions of flexible risers. PETROBRAS has been monitoring the pressure of permeated gas in the annulus region of some risers in order to infer the eventual occurrence of non-conformities as damage on the riser external sheath, for example. Such occurrence would affect the permeated gas flow pattern, the gas pressurization period and the relief valve opening frequencies. Furthermore, the mentioned occurrence would increase the susceptibility of the steel armors to experience the potential failure mechanism of corrosion. In PETROBRAS, the current monitoring method is characterized by visual and periodic manometer readings from a manometer set installed near each riser end-fitting. The data is recorded in a daily report and analyzed by personnel onshore, who are in charge of comparing data and requesting relief valve's actuation, whenever necessary. The paper illustrates Marlim-Sul Asset experience on monitoring and data processing to control the annulus conditions of flexible risers during operation. It presents the in-house developed methodology to data management and processing. This methodology is based on a daily analysis of the permeated gas data worksheet. Some examples are given to illustrate it. The paper also summarizes current developments, in progress, in order to improve riser integrity management. The first development is being done to implement, in the future, automatic data acquisition and control systems. The purpose of automating this process is to improve methods and techniques for data acquisition, transmission and processing. The second development focuses on applications in which riser top end-fittings are submerged. In this particular scenario, a special system - with a quick connection sub sea device - is under development to allow the connection, by divers, after the riser pull-in, of the riser annulus to the platform gas

Tools for in service monitoring and testing of riser to prevent failure and extend service life

Energy Technology Data Exchange (ETDEWEB)

Ward, Haakon; Bondevik, Jon Olav; Skjerve, Haavard; Tveit, Oeyvind [SeaFlex AS, Asker (Norway)

2005-07-01

Exploration and development of new oil and gas fields is heavily dependant on use of flexible pipes and many field developments would not have been possible without them. The number of flexible risers in service is constantly increasing since relatively few offshore projects have reached the estimated operational life and the operational lifetime of several fields in-service has been extended due to new and improved technology. Many risers have been in service over a large number of years. Some risers have been operated under demanding conditions such as severe dynamic loads, high pressure and temperatures. One may in some cases find that risers actually have shorter service life than estimated in the design phase due to the severe operational conditions. In order to extend the use of the riser, some risers may have to be modified and re-terminated and prepared for a new and less demanding application. In order to operate risers safely, it is important to re-assess the fatigue life in order to prevent potential riser failure. The operator should implement methods and tools for in-service monitoring and testing. This paper addresses efficient and reliable methods and tools for monitoring of critical operational parameters as well as in-service riser testing. A brief description of structural failure modes will also be given in order to understand how to interpret test results in view of potential failure modes. (author)

NMR-ON on 60CoCo(fcc, hcp, thin film), 52MnCo(fcc), and 90NbCo(fcc)

International Nuclear Information System (INIS)

Zech, E.; Hagn, E.; Ernst, H.; Eska, G.

1978-01-01

With the NMR-ON method the magnetic hyperfine splitting constant of dilute impurities in a ferromagnetic host material (Fe, Ni, Co) can be determined with high accuracy (10 -3 ...10 -4 ). Only few NMR-ON experiments with Co as host lattice have been performed up to now. In constrast to Fe and Ni, two stable modifications exist for Co (fcc and hcp). In the hcp case the magnetic hyperfine field is expected to be anisotropic. Due to the electric field gradient, which is present in this case, a (small) guadrupole interaction is superimposed to the magnetic hyperfine interaction. For 60 CoCo measurements were done on a fcc foil, a hcp single crystal, and on thin films, which were prepared by evaporating Co into glass. For 52 MnCo and 90 NbCo measurements were performed for fcc Co. (Auth.)

Lattice Dynamics of fcc Ca

DEFF Research Database (Denmark)

Stassis, C.; Zaretsky, J.; Misemer, D. K.;

1983-01-01

A large single crystal of FCC Ca was grown and was used to study the lattice dynamics of this divalent metal by coherent inelastic neutron scattering. The phonon dispersion curves were measured, at room temperature, along the [ξ00], [ξξ0], [ξξξ], and [0ξ1] symmetry directions. The dispersion curves...... to the propagation of elastic waves. The frequencies of the T1[ξξ0] branch for ξ between approximately 0.5 and 0.8 are slightly above the velocity-of-sound line determined from the low-frequency measurements. Since a similar effect has been observed in FCC Yb, it is natural to assume that the anomalous dispersion...... bear a striking resemblance to those of FCC Yb, which is also a divalent metal with an electronic band structure similar to that of Ca. In particular, the shear moduli c44 and (c11-c 12)/2 differ by a factor of 3.4, which implies that FCC Ca (like FCC Yb) is very anisotropic with regard...

Oscillation of a rigid catenary riser due to the internal two-phase flow

Energy Technology Data Exchange (ETDEWEB)

Bordalo, Sergio N.; Morooka, Celso K.; Cavalcante, Cesar C.P. [Universidade Estadual de Campinas (UNICAMP), SP (Brazil); Matt, Cyntia G.C.; Franciss, Ricardo [PETROBRAS, Rio de Janeiro, RJ (Brazil). Centro de Pesquisas

2008-07-01

Production of petroleum reservoirs from deep and ultra-deep waters is of paramount importance in Brazil, and several researches are necessary to develop appropriated equipment and risers for those operational conditions. Risers are suspended pipes used to transport the petroleum fluids between the seabed and the floating production unit. The structural flexibility of riser's lines is conferred by its length when compared with the diameter, characterizing it as a slender body. The risers are submitted to large static and dynamic loads originated from its own weight, waves, currents, platform motions and the internal flow. These loadings may threaten, by fatigue, the structural integrity of the system, compromising its useful life, and so they must be considered in the riser's project. There is a large amount of knowledge in the literature about the effects of external loadings on these systems, but the effect of the internal flow remains vastly unexplored. The variation of the flow mass and momentum inside the riser causes a dynamic loading on this system, originating an oscillatory motion. Furthermore, the gas-liquid two-phase flow may assume several flow patterns (bubble, slug, intermittent or annular), each one possessing completely different characteristics. In this work, the influence of the internal flow on the oscillatory motion (whipping motion) of catenary risers is analyzed. To provide a better understanding of this physical phenomenon, a scaled apparatus was designed and built. The material used to manufacture the riser's model was a flexible silicone tube, and air and water were used to simulate the two-phase flow. The instrumentation used to measure the fluids flow rates and the sustaining force at the top of the model was installed in the apparatus. A video acquisition system was used to determine the displacements, and frequency spectrum, of color targets positioned throughout the model, under several flow conditions. The flow patterns

Reliable Radiographic Inspection of Flexible Risers for the Oil Industry

Science.gov (United States)

Almeida, Rômulo M.; Rebello, Joao Marcos A.; Vaz, Murilo A.

2010-02-01

Flexible risers are composite tubular structures manufactured by the concentric assemblage of cylindrical polymeric and helically wound metallic layers employed to convey pressurized fluids such as oil, gas and water in the ocean environment. The metallic layers account for the flexible risers' structural strength and are dimensioned according to the static and dynamic loads. They are usually installed in a free hanging catenary configuration and are subjected to the direct action of waves and marine currents and wave induced motions from the oil production platform. The fatigue rupture of wire armours in the end fitting or within the riser segment protected by the bend stiffener is an object of major concern. Integrity models have been developed, however inspection techniques are mandatory to ensure that failure is detected. Gammagraphy has been used as a common inspection technique in all regions of the flexible riser, mainly with the single wall-single view method. On the other side, there is not any qualified radiographic procedure to this kind of structure. Radiographic simulation was adopted and its validation with actual gammagraphies and establishment of radiographic parameters to complex radiation geometries were done. Results show the viability of the radiographic inspection analyzing the armour wires' rupture and the displacement between wires.

RELIABLE RADIOGRAPHIC INSPECTION OF FLEXIBLE RISERS FOR THE OIL INDUSTRY

International Nuclear Information System (INIS)

Almeida, Romulo M.; Rebello, Joao Marcos A.; Vaz, Murilo A.

2010-01-01

Flexible risers are composite tubular structures manufactured by the concentric assemblage of cylindrical polymeric and helically wound metallic layers employed to convey pressurized fluids such as oil, gas and water in the ocean environment. The metallic layers account for the flexible risers' structural strength and are dimensioned according to the static and dynamic loads. They are usually installed in a free hanging catenary configuration and are subjected to the direct action of waves and marine currents and wave induced motions from the oil production platform. The fatigue rupture of wire armours in the end fitting or within the riser segment protected by the bend stiffener is an object of major concern. Integrity models have been developed, however inspection techniques are mandatory to ensure that failure is detected. Gammagraphy has been used as a common inspection technique in all regions of the flexible riser, mainly with the single wall-single view method. On the other side, there is not any qualified radiographic procedure to this kind of structure. Radiographic simulation was adopted and its validation with actual gammagraphies and establishment of radiographic parameters to complex radiation geometries were done. Results show the viability of the radiographic inspection analyzing the armour wires' rupture and the displacement between wires.

Development and characterization of composite materials for production of composite risers by filament winding

Directory of Open Access Journals (Sweden)

Ledjane Lima Sobrinho

2011-09-01

Full Text Available Industry has been challenged to provide riser systems which are more cost effective and which can fill the technology gaps with respect to water depth, riser diameter and high temperatures left open by flexibles, steel catenary risers (SCRs and hybrid risers. Composite materials present advantages over conventional steel risers because composite materials are lighter, more fatigue and corrosion resistant, better thermal insulators and can be designed for improving the structural and mechanical response. This paper contains a study of the toughening mechanism of an epoxy resin under rubber addition by means of fractographic analysis and its relation with the fracture process and increase of strength of a composite riser employing this polymeric matrix. Initially, an epoxy resin system was toughened by rubber CTBN addition (10 wt. (% as a way of improving the flexibility of future risers. Mechanical and thermal analyses were carried out for characterizing the polymeric systems. Later, composite tubes were prepared and mechanically characterized. The influence of matrix toughening on the mechanical behavior of the tubes was also studied. Split-disk tests were used to determine the hoop tensile strength of these specimens. The results indicate that the matrix plays an important role in composite fracture processes. The adding rubber to the polymeric matrix promoted a simultaneous increase of stress and elongation at fracture of the tubes manufactured herein, which is not often reported. These results, probably, is function of better adhesion between fibers and polymeric matrix observed in the CTBN-modified composite rings, which was evidenced in the fractografic analysis by SEM after the split-disk tests.

Riser configuration, Tank 241-A-105, light duty utility arm

International Nuclear Information System (INIS)

Boucher, T.D.

1994-01-01

The light-duty utility arm (LDUA) is a seven-joint stainless steel robotic arm with a payload capacity of 75 lb. The robotic arm is deployed vertically with a maximum vertical reach of 63 ft. and a maximum horizontal reach of 13.5 ft. The functional requirements of the LDUA system are mapping and characterization of waste in Hanford single-shell tanks (SST) before and during waste retrieval. The LDUA system consists of a mobile deployment system (MDS), a vertical positioning mast (VPM), a tank riser interface confinement (TRIC), the LDUA, and a controller subsystem or support trailer. Currently, the system is in design and is subject to change; however, the LDUA or robotic arm will be deployed through a 12-in. riser above the tank dome. Field trips were performed to gather specifics for future deployment of the LDUA in Tank 241-A-105. The purpose of this report is to support two previous reports for the investigation of SSTs for deployment of the LDUA system. The first report identified the availability of risers while the second report identified the availability of Tanks 241-A-105, 241-A-S-109, 241-A-T-101, and 241-A-T-109 for deployment of the LDUA system. The second report also identified those 4- and 12-in. risers that could be used for deployment of the LDUA and camera system. This report addresses accessibility to the 241-A Tank Farm and the usability of the Tank 241-A-105 risers. The following information for assisting in the design and deployment of the LDUA will be discussed in this report: radiation survey; flange identification; high resolution video; computer simulated model; and field survey

9th FCC-ee (TLEP) Physics Workshop

CERN Document Server

2015-01-01

This is the 9th in the series of FCCee/TLEP-related workshops. It follows on from the sucessful 8th TLEP workshop that took place in Paris on 27-29 October 2014, and the FCC kick-off meeting held on 12-15 February 2014 at University of Geneva. The workshop is open to all FCC-ee /TLEP design study members, and more generally to all interested in a precision Z, W, H, top factory. The focus will be on physics and experiments at the FCC-ee, but a more general session is organized the first day (Tuesday 3 February afternoon) with presentations about the FCC design study as a whole, and on machine and physics for the FCC-ee and the FCC-hh, with synergies and complementarities. This session is aimed at a larger audience, towards improving the project visibility in Italy. It will be followed by a social dinner in the evening. The workshop starts on Tuesday at 13:30 and ends on Thursday 16:00. Registration is now open, please proceed at your earliest convenience! Please visit the FCC-ee / TLEP web site, and subscrib...

Three-Dimensional Dynamics of a Flexible Marine Riser Undergoing Large Elastic Deformations

International Nuclear Information System (INIS)

Raman-Nair, W.; Baddour, R.E.

2003-01-01

The equations of the three dimensional motion of a marine riser undergoing large elastic deformations are formulated using Kane's formalism. The riser is modeled using lumped masses connected by extensional and rotational springs including structural damping. Surface waves are described by Stokes? second-order wave theory. Fluid-structure coupling is achieved by application of the hydrodynamic loads via Morison's equation and added-mass coefficients using the instantaneous relative velocities and accelerations between the fluid field and the riser segments. In the same way, a model for incorporating the effects of vortex-induced lift forces is included. The effect of internal flow is included in the model. The detailed algorithm is presented and the equations are solved using a robust implementation of the Runge-Kutta method provided in MATLAB. The mathematical model and associated algorithm are validated by comparing the steady-state equilibrium configuration of the riser with special cases of an elastic catenary mooring line and large deflection statics of a cantilever beam. The results of sample simulations are presented

An optical sensor for the detection of leaks from subsea pipelines and risers

International Nuclear Information System (INIS)

McStay, D; Kerlin, J; Acheson, R

2007-01-01

An optical sensor for the rapid detection of detect leaks of oil, hydraulic fluids or leak detection chemicals from underwater pipelines and risers is reported. The sensor is designed to be deployed on ROVs or AUVs for the rapid survey of underwater pipelines and risers. The system employs ultra-bright LEDs to project a sensing light beam into the water to allow real time detection of ppm concentration plumes of material leaking from pipelines or riser in real time. Typically the system is deployed on an ROV which inspects a pipeline at a height of 2-3m

Numerical simulation of thermal-hydraulic processes in the riser chamber of installation for clinker production

Directory of Open Access Journals (Sweden)

Borsuk Grzegorz

2016-03-01

Full Text Available Clinker burning process has a decisive influence on energy consumption and the cost of cement production. A new problem is to use the process of decarbonization of alternative fuels from waste. These issues are particularly important in the introduction of a two-stage combustion of fuel in a rotary kiln without the typical reactor-decarbonizator. This work presents results of numerical studies on thermal-hydraulic phenomena in the riser chamber, which will be designed to burn fuel in the system where combustion air is supplied separately from the clinker cooler. The mathematical model is based on a combination of two methods of motion description: Euler description for the gas phase and Lagrange description for particles. Heat transfer between particles of raw material and gas was added to the numerical calculations. The main aim of the research was finding the correct fractional distribution of particles. For assumed particle distribution on the first stage of work, authors noted that all particles were carried away by the upper outlet to the preheater tower, what is not corresponding to the results of experimental studies. The obtained results of calculations can be the basis for further optimization of the design and operating conditions in the riser chamber with the implementation of the system.

Singing mitigation in an export riser via liquid injection: a field case study

NARCIS (Netherlands)

Belfroid, S.P.C.; Korst, H.J.C.; Beek, P.J.G. van; Lunde, K.; Eidsvik, I.G.; Hansen, F.; Olsen, B.

2014-01-01

Flexible Risers are prone to the generation of high amplitude tonal noise, i.e. a so-called singing riser. Recently, severe vibrations and high noise levels were encountered on the turret of an FPSO in the Norwegian Sea, resulting in significantly reduced production. The vibrations could be

The FCC-ee study: Progress and challenges

OpenAIRE

Koratzinos, Michael; Aumon, Sandra; Bogomyagkov, Anton; Boscolo, Manuela; Cook, Charlie; Doblhammer, Andreas; Härer, Bastian; Tomás, Rogelio; Levichev, Evgeny; Medina Medrano, Luis; Shatilov, Dmitry; Wienands, Ulrich; Zimmermann, Frank

2015-01-01

The FCC (Future Circular Collider) study represents a vision for the next large project in high energy physics, comprising an 80-100 km tunnel that can house a future 100 TeV hadron collider. The study also includes a high luminosity e+e- collider operating in the centre-of-mass energy range of 90-350 GeV as a possible intermediate step, the FCC-ee. The FCC-ee aims at definitive electro-weak precision measurements of the Z, W, H and top particles, and search for rare phenomena. Although FCC-e...

Spontaneous recombination volumes of Frenkel defects in neutron-irradiated non-fcc metals

International Nuclear Information System (INIS)

Nakagawa, M.; Mansel, W.; Boening, K.; Rosner, P.; Vogl, G.

1979-01-01

Production and production-rate curves for the non-fcc metals Fe, Mo, Ta, W, Zr, and Sn are obtained by electrical-resistivity measurements taken at 4.6 K during reactor neutron irradiations. The saturation concentration of Frenkel defects, c/sub s/, and the recombination volume v/sub o/ are evaluated. A parabolic relation between the spontaneous recombination volume v 0 and the compressibility kappa for a series of bcc metals is found

FCC Official Brochure - Japanese Version

CERN Multimedia

AUTHOR|(CDS)2082248; Yamamoto, Akira; Uchibori, Yumemi.katsuki

2017-01-01

The FCC brochure describes the main scope of the study and give more information about the main scenarios explored under the study. It also highlights the ongoing R&D efforts launched by the FCC study. Finally, it offers more information about the collaboration and a list of useful contact details.

FCC Official Brochure - French Version

CERN Multimedia

Charitos, Panagiotis

2017-01-01

The FCC brochure describes the main scope of the study and give more information about the main scenarios explored under the study. It also highlights the ongoing R&D efforts launched by the FCC study. Finally, it offers more information about the collaboration and a list of useful contact details.

FCC Official Brochure - German version

CERN Multimedia

Charitos, Panagiotis

2017-01-01

The FCC brochure describes the main scope of the study and give more information about the main scenarios explored under the study. It also highlights the ongoing R&D efforts launched by the FCC study. Finally, it offers more information about the collaboration and a list of useful contact details.

The Sleipner riser platform experience

International Nuclear Information System (INIS)

Anon.

1993-01-01

The article discusses briefly the Norwegian Sleipner riser project. The project has provided new insight on how to handle smaller development projects in a time saving and cost effective way. Through active cooperation between the prime contractors, the total project time, which included engineering, fabrication ready to tow, was slashed to a record 11 months. Normally, such a project would take a couple of years to complete. 1 fig

Inspection and monitoring techniques for un-bonded flexible risers and pipelines

OpenAIRE

Simonsen, Anders

2014-01-01

Master's thesis in Offshore technology Un-bonded flexible pipelines and risers are an alternative to conventional rigid steel pipes. The use of flexible pipes has enabled development of several offshore fields that seemed unfeasible with the use of rigid pipes due to extensive seabed preparation and large dynamic motions. The lack of knowledge and integrity management tools for flexible pipes is a limiting factor and cause pipelines and risers to be replaced before their service life has ...

Design study of an IHX support structure for a POOL-TYPE Sodium-cooled fast reactor

International Nuclear Information System (INIS)

Park, Chang Gyu; Kim, Jong Bum; Lee, Jae Han

2009-01-01

The IHX (Intermediate Heat eXchanger) for a pool-type SFR (Sodium-cooled Fast Reactor) system transfers heat from the primary high temperature sodium to the intermediate cold temperature sodium. The upper structure of the IHX is a coaxial structure designed to form a flow path for both the secondary high temperature and low temperature sodium. The coaxial structure of the IHX consists of a central downcomer and riser for the incoming and outgoing intermediate sodium, respectively. The IHX of a pool-type SFR is supported at the upper surface of the reactor head with an IHX support structure that connects the IHX riser cylinder to the reactor head. The reactor head is generally maintained at the low temperature regime, but the riser cylinder is exposed in the elevated temperature region. The resultant complicated temperature distribution of the co-axial structure including the IHX support structure may induce a severe thermal stress distribution. In this study, the structural feasibility of the current upper support structure concept is investigated through a preliminary stress analysis and an alternative design concept to accommodate the IHTS (Intermediate Heat Transport System) piping expansion loads and severe thermal stress is proposed. Through the structural analysis it is found that the alternative design concept is effective in reducing the thermal stress and acquiring structural integrity

An experimental study on the key fretting variables for flexible marine risers

OpenAIRE

O’Halloran, S.M.; Harte, A.M.; Shipway, P.H.; Leen, S.B.

2018-01-01

This paper presents an experimental investigation into the effects of contact conformity, contact pressure and displacement amplitude on the gross-slip fretting behaviour grease-lubricated cylinder-on-flat contacts in the context of flexible marine riser pressure armour wire, and compares behaviour with that observed in unlubricated conditions. Characterisation of friction and wear is critical to fretting fatigue life prediction in flexible risers since friction directly controls trailing-edg...

FCC-ee Physics workshop | 19-21 June 2014

CERN Multimedia

2014-01-01

The 7th FCC-ee/TLEP workshop, the first after the FCC kick-off in February 2014, will be focused on physics and experiments.     It will take place on 19-21 June at CERN in the TH auditorium. The registration is open and the agenda is available on the indico web page: http://indico.cern.ch/event/313708/. You are all cordially invited to attend! This will be the first in a series of workshops that will lead us to the first FCC-ee physics milestone, a document defining the physics landscape and study plans, required for March 2015. More information can be found here. FCC-ee is a high-luminosity Z, W, Higgs and top factory, to be hosted in a 100km tunnel, possibly as the first step towards a 100 TeV pp collider FCC-hh. These two machines are being studied within the FCC design study. High precision, high statistics and a clean environment are the tools available in FCC-ee to shed light on the unknown physics that underlies present mysteries: dark matter, the baryon asymmetry of th...

FCC 3 and FCC 4 (2/4)

CERN Multimedia

CERN. Geneva; Dam, Mogens

2016-01-01

Abstract: Owing to its specific interaction region design, the FCC-ee will be able to deliver unprecedented luminosities at centre-of-mass energies ranging from below the Z pole to the ttbar threshold and above. Operation at four energy regimes - at the Z pole, at the WW threshold, at 240 GeV for Higgs production, and at the ttbar thre...

Vector form Intrinsic Finite Element Method for the Two-Dimensional Analysis of Marine Risers with Large Deformations

Science.gov (United States)

Li, Xiaomin; Guo, Xueli; Guo, Haiyan

2018-06-01

Robust numerical models that describe the complex behaviors of risers are needed because these constitute dynamically sensitive systems. This paper presents a simple and efficient algorithm for the nonlinear static and dynamic analyses of marine risers. The proposed approach uses the vector form intrinsic finite element (VFIFE) method, which is based on vector mechanics theory and numerical calculation. In this method, the risers are described by a set of particles directly governed by Newton's second law and are connected by weightless elements that can only resist internal forces. The method does not require the integration of the stiffness matrix, nor does it need iterations to solve the governing equations. Due to these advantages, the method can easily increase or decrease the element and change the boundary conditions, thus representing an innovative concept of solving nonlinear behaviors, such as large deformation and large displacement. To prove the feasibility of the VFIFE method in the analysis of the risers, rigid and flexible risers belonging to two different categories of marine risers, which usually have differences in modeling and solving methods, are employed in the present study. In the analysis, the plane beam element is adopted in the simulation of interaction forces between the particles and the axial force, shear force, and bending moment are also considered. The results are compared with the conventional finite element method (FEM) and those reported in the related literature. The findings revealed that both the rigid and flexible risers could be modeled in a similar unified analysis model and that the VFIFE method is feasible for solving problems related to the complex behaviors of marine risers.

Numerical simulations of the dynamic of steel catenary riser under the influence of VIV-Vortex-Induced Vibration

Energy Technology Data Exchange (ETDEWEB)

Tsukada, Raphael I.; Morooka, Celso K. [Universidade Estadual de Campinas (UNICAMP), SP (Brazil). Faculdade de Engenharia Mecanica; Franciss, Ricardo; Matt, Cyntia G.C. [Petroleo Brasileiro S.A. (PETROBRAS), Rio de Janeiro, RJ (Brazil). Centro de Pesquisas (CENPES)

2009-07-01

Hydrocarbon discoveries in ultra deep waters and the recent pre-salt deep carbonate reservoirs along the Brazilian coast demand further technological development in order to exploit these resources. These developments usually require new concepts for offshore sea surface structures and subsea systems for the petroleum and gas production, which means cost effective solutions that provides higher operational safety on drilling and production operations. In this scenario, the effect of the natural phenomenon of Vortex-Induced Vibration (VIV) on risers is one of the concerns for its design due to the tendency of VIV to increase levels of stresses in the riser structure. Therefore the correct prediction of stresses and displacements due to VIV is of great importance for designing riser systems. The present work presents new developments based on previous results for VIV in vertical risers extended to curved risers such as steel catenary risers (SCR). Numerical simulations have been performed in time domain, and experimental results from model tests with a scaled SCR in a towing tank have been used to evaluate the proposed developments. Finally, the conclusions from the analysis of the results bring very promising results. (author)

Simulation of short-term annealing of displacement cascades in FCC metals

International Nuclear Information System (INIS)

Heinisch, H.L.; Doran, D.G.; Schwartz, D.M.

1980-01-01

Computer models have been developed for the simulation of high energy displacement cascades. The objective is the generation of defect production functions for use in correlation analysis of radiation effects in fusion reactor materials. In particular, the stochastic cascade annealing simulation code SCAS has been developed and used to model the short-term annealing behavior of simulated cascades in FCC metals. The code is fast enough to make annealing of high energy cascades practical. Sets of cascades from 5 keV to 100 keV in copper were generated by the binary collision code MARLOWE

Recreating Riser Slugging Flow Based on an Economic Lab-sized Setup

DEFF Research Database (Denmark)

Hansen, Lasse; Pedersen, Simon; Yang, Zhenyu

2013-01-01

As a kind of periodic phenomenon, the slugging flow in the offshore oil & gas production addresses a lot of attentions, due to its limitation of production rate, periodic overload processing facilities, and even direct cause of emergent shutdown. This work studies the emulation of the riser...... slugging flow in the offshore oil & gas production, by constructing an economical lab-sized setup in the university campus. Firstly, the construction and used components for the lab setup are illustrated; then, the constructed setup is validated by checking the consistency with some existing typical riser...

Analysis of the effects of corrosion probe on riser 241-AN-102-WST-16 during seismic event

International Nuclear Information System (INIS)

ZIADA, H.H.

1998-01-01

This analysis supports the installation activity of the corrosion probe in Tank 241-AN-102. The probe is scheduled to be installed in Riser 241-AN-102-WST-16 (formerly known as Riser 15B). The purpose of this analysis is to evaluate the potential effect of the corrosion probe on the riser during a credible seismic event. The previous analysis (HNF 1997a) considered only pump jet impingement loading

Reliability-based dynamic positioning of floating vessels with riser and mooring system

DEFF Research Database (Denmark)

Fang, Shaoji; Leira, Bernt J.; Blanke, Mogens

2011-01-01

To maintain safety of a floating vessel with associated slender components such as risers and mooring line, the vessel is normally kept within a limited region. To specify a safe position in that region, this paper suggests a new position chasing algorithm with the consideration of both riser ang...... to their criticality. An optimal position set-point is produced by minimization of the value of the cost function. Numerical simulations show the effectiveness of the proposed algorithm....

PURIFIED WASTE FCC CATALYST AS A CEMENT REPLACEMENT MATERIAL

Directory of Open Access Journals (Sweden)

Danute Vaiciukyniene

2015-06-01

Full Text Available Zeolites are commonly used in the fluid catalytic cracking process. Zeolite polluted with oil products and became waste after some time used. The quantity of this waste inevitably rises by expanding rapidly oil industry. The composition of these catalysts depends on the manufacturer and on the process that is going to be used. The main factors retarding hydration process of cement systems and modifying them strength are organic compounds impurities in the waste FCC catalyst. The present paper shows the results of using purified waste FCC catalyst (pFCC from Lithuania oil refinery, as Portland cement replacement material. For this purpose, the purification of waste FCC catalyst (FCC samples was treated with hydrogen peroxide. Hydrogen peroxide (H2O2 is one of the most powerful oxidizers known. By acting of waste with H2O2 it can eliminate the aforementioned waste deficiency, and the obtained product becomes one of the most promising ingredients, in new advanced building materials. Hardened cement paste samples with FCC or pFCC were formed. It was observed that the pFCC blended cements developed higher strength, after 28 days, compared to the samples with FCC or reference samples. Typical content of Portland cement substituting does not exceed 30 % of mass of Portland cement in samples. Reducing the consumption of Portland cement with utilizing waste materials is preferred for reasons of environmental protection.

Fatigue Strength of Titanium Risers - Defect Sensitivity

Energy Technology Data Exchange (ETDEWEB)

Babalola, Olusegun Tunde

2001-07-01

This study is centred on assessment of the fatigue strength of titanium fusion welds for deep-water riser's applications. Deep-water risers are subjected to significant fatigue loading. Relevant fatigue data for titanium fusion welds are very scarce. Hence there is a need for fatigue data and life prediction models for such weldments. The study has covered three topics: Fatigue testing, Fractography and defect assessment, and Fracture Mechanics modelling of fatigue crack growth. Two series of welded grade of titanium consisting of 14 specimens in each series were fatigue tested under constant amplitude loading. Prior to fatigue testing, strain gauge measurements of some specimens was conducted to enable the definition of stress range in the fatigue assessment procedure. The results were compared with finite solid element analysis and related to fatigue stresses in a riser pipe wall. Distribution and geometry of internal and surface defects both in the as-welded and in the post-weld machined conditions were assessed using fractography. This served as a tool to determine the fatigue initiation point in the welds. Fracture mechanics was applied to model fatigue strength of titanium welds with initiation from weld defects. Two different stress intensity factor formulations for embedded eccentrically placed cracks were used for analysis of elliptical cracks with the major axis parallel and close to one of the free surfaces. The methods were combined to give a satisfactory model for crack growth analysis. The model analyses crack growth of elliptical and semi-elliptical cracks in two directions, with updating of the crack geometry. Fatigue strength assessment was conducted using two crack growth models, the Paris-Erdogan relation with no threshold and the Donahue et al. relation with an implied threshold. The model was validated against experimental data, with a discussion on the choice of crack growth model. (author)

FCC-ee: Energy Calibration

Energy Technology Data Exchange (ETDEWEB)

Koratzinos, M. [Univ. of Geneva (Switzerland); Blondel, A. [Univ. of Geneva (Switzerland); Gianfelice-Wendt, E. [Fermi National Accelerator Lab. (FNAL), Batavia, IL (United States); Zimmermann, F. [European Organization for Nuclear Research (CERN), Geneva (Switzerland)

2015-06-02

The FCC-ee aims to improve on electroweak precision measurements, with goals of 100 ke V on the Z mass and width, and a fraction of MeV on the W mass. Compared to LEP, this implies a much improved knowledge of the center-of-mass energy when operating at the Z peak and WW threshold. This can be achieved by making systematic use of resonant depolarization. A number of issues have been identified, due in particular to the long polarization times. However the smaller emittance and energy spread of FCC-ee with respect to LEP should help achieve a much improved performance.

FCC-ee: Energy calibration

CERN Document Server

Koratzinos, M.; Gianfelice-Wendt, E.; Zimmermann, F.

The FCC-ee aims to improve on electroweak precision measurements, with goals of 100 keV on the Z mass and width, and a fraction of MeV on the W mass. Compared to LEP, this implies a much improved knowledge of the centre-of-mass energy when operating at the Z peak and WW threshold. This can be achieved by making systematic use of resonant depolarization. A number of issues have been identified, due in particular to the long polarization times. However the smaller emittance and energy spread of FCC-ee with respect to LEP should help achieve a much improved performance.

Single-shell tank riser resistance to ground test plan

International Nuclear Information System (INIS)

Kiewert, L.R.

1996-01-01

This Test Procedure provides the general directions for conducting Single-Shell Tank Riser to Earth Measurements which will be used by engineering as a step towards providing closure for the Lightning Hazard Issue

A numerical study of boiling flow instability of a reactor thermosyphon system

International Nuclear Information System (INIS)

Nayak, A.K.; Lathouwers, D.; Hagen, T.H.J.J. van der; Schrauwen, Frans; Molenaar, Peter; Rogers, Andrew

2006-01-01

A numerical study has been carried out to investigate the boiling flow instability of a reactor thermosyphon system. The numerical model solves the conservation equations of mass, momentum and energy applicable to a two-fluid and three-field steam-water system using a finite difference technique. The computer code MONA was used for this purpose. The code was applied to the thermosyphon system of an EO (ethylene oxide) chemical reactor in which the heat released by a catalytic reaction is carried by boiling water under natural circulation conditions. The steady-state characteristics of the reactor thermosyphon system were predicted using the MONA code and conventional two-phase flow models in order to understand the model applicability for this type of thermosyphon system. The two-fluid model was found to predict the flow closest to the measured value of the plant. The stability behaviour of the thermosyphon system was investigated for a wide range of operating conditions. The effects of power, subcooling, riser length and riser diameter on the boiling flow instability were determined. The system was found to be unstable at higher power conditions which is typical for a Type II instability. However, with an increase in riser diameter, oscillations at low power were observed as well. These are classified as Type I instabilities. Stability maps were predicted for both Type I and Type II instabilities. Methods of improving the stability of the system are discussed

A numerical study of boiling flow instability of a reactor thermosyphon system

Energy Technology Data Exchange (ETDEWEB)

Nayak, A.K.; Lathouwers, D.; Hagen, T.H.J.J. van der [Interfaculty Reactor Institute, Delft University of Technology, Mekelweg 15, 2629 JB Delft (Netherlands); Schrauwen, Frans; Molenaar, Peter; Rogers, Andrew [Shell Research and Technology Centre, Badhuisweg 3, 1031 CM Amsterdam (Netherlands)

2006-04-01

A numerical study has been carried out to investigate the boiling flow instability of a reactor thermosyphon system. The numerical model solves the conservation equations of mass, momentum and energy applicable to a two-fluid and three-field steam-water system using a finite difference technique. The computer code MONA was used for this purpose. The code was applied to the thermosyphon system of an EO (ethylene oxide) chemical reactor in which the heat released by a catalytic reaction is carried by boiling water under natural circulation conditions. The steady-state characteristics of the reactor thermosyphon system were predicted using the MONA code and conventional two-phase flow models in order to understand the model applicability for this type of thermosyphon system. The two-fluid model was found to predict the flow closest to the measured value of the plant. The stability behaviour of the thermosyphon system was investigated for a wide range of operating conditions. The effects of power, subcooling, riser length and riser diameter on the boiling flow instability were determined. The system was found to be unstable at higher power conditions which is typical for a Type II instability. However, with an increase in riser diameter, oscillations at low power were observed as well. These are classified as Type I instabilities. Stability maps were predicted for both Type I and Type II instabilities. Methods of improving the stability of the system are discussed. [Author].

Outline and Status of the FCC-ee Design Study

CERN Document Server

Zimmermann, Frank

2015-01-01

The Update of the European Strategy for Particle Physics in 2013 [1] declared as its second highest priority that “…to propose an ambitious post-LHC accelerator project….., CERN should undertake design studies for accelerator projects in a global context,…with emphasis on proton-proton and electron-positron high-energy frontier machines…”. In response to this request, the global Future Circular Collider (FCC) study is designing a 100-TeV proton collider (FCC-hh) in a new ~100 km tunnel near Geneva, a high-luminosity electron-positron collider (FCC-ee) as a potential intermediate step, and a lepton-hadron option (FCC-he). The FCC study comprises accelerators, technology, infrastructure, detector, physics, concepts for worldwide data services, international governance models, and implementation scenarios. The FCC study is mandated to deliver a Conceptual Design Report and preliminary cost estimate by the time of the next European Strategy Update expected for 2019. As of July 2015, 58 institutes from...

Remote installation of risers on underground nuclear waste storage tanks

International Nuclear Information System (INIS)

Jackson, J.P.; Gessner, R.F.

1988-03-01

The West Valley Demonstration Project was established to solidify 2120 m 3 (560,000) gallons of high-level nuclear waste generated during six years of commercial nuclear fuel reprocessing. This liquid will be processed to remove radioactive elements which, with the remaining sludge, will be combined with glass formers and be converted into borosilicate glass. Risers were installed on the high-level tank for installation of pumps which will be used to remove the liquid and sludge. The extensive use of remote technology was required to install the risers and to minimize operator exposure to high levels of radiation and contamination. The riser installation required remotely: drilling through two feet of concrete shielding; installing pump access pipes which are welded to the tank top; and cutting holes in tanks located 3658 mm (12) feet below ground. These operations were successfully completed 13 times without exposing personnel to high-level radiation or contamination. Specially designed remote equipment was developed for each step of this operation. Extensive operator training in the use of this equipment was performed on a tank with low radiation prior to work on the high-level tank. This paper discusses the application of remote technology that assured a quality job was safely accomplished. 3 refs., 18 figs., 2 tabs

Numerical Simulation of the Vortex-Induced Vibration of A Curved Flexible Riser in Shear Flow

Science.gov (United States)

Zhu, Hong-jun; Lin, Peng-zhi

2018-06-01

A series of fully three-dimensional (3D) numerical simulations of flow past a free-to-oscillate curved flexible riser in shear flow were conducted at Reynolds number of 185-1015. The numerical results obtained by the two-way fluid-structure interaction (FSI) simulations are in good agreement with the experimental results reported in the earlier study. It is further found that the frequency transition is out of phase not only in the inline (IL) and crossflow (CF) directions but also along the span direction. The mode competition leads to the non-zero nodes of the rootmean- square (RMS) amplitude and the relatively chaotic trajectories. The fluid-structure interaction is to some extent reflected by the transverse velocity of the ambient fluid, which reaches the maximum value when the riser reaches the equilibrium position. Moreover, the local maximum transverse velocities occur at the peak CF amplitudes, and the values are relatively large when the vibration is in the resonance regions. The 3D vortex columns are shed nearly parallel to the axis of the curved flexible riser. As the local Reynolds number increases from 0 at the bottom of the riser to the maximum value at the top, the wake undergoes a transition from a two-dimensional structure to a 3D one. More irregular small-scale vortices appeared at the wake region of the riser, undergoing large amplitude responses.

Study of Collective Effects in the FCC-ee Collider

OpenAIRE

Zobov, Mikhail; Belli, Eleonora; Castorina, Giovanni; Migliorati, Mauro; Persichelli, Serena; Rumolo, Giovanni; Spataro, Bruno

2018-01-01

The Future Circular Collider (FCC) study aims at designing different options of a post-LHC collider. The high luminosity electron-positron collider FCC-ee based on the crab waist concept is considered as an intermediate step on the way towards FCC-hh, a 100 TeV hadron collider using the same tunnel of about 100 km. Due to a high intensity of circulating beams the impact of collective effects on FCC-ee performance has to be carefully analyzed. In this paper we evaluate beam coupling impedance ...

Dalia integrated production bundle (IPB): an innovative riser solution for deep water fields

Energy Technology Data Exchange (ETDEWEB)

Reals, Th Boscals de; Gloaguen, M.; Roche, F. [Total E and P (Angola); Marion, A.; Poincheval, A. [Technip, Paris (France)

2008-07-01

The Dalia field is located 210 km north west of Luanda (Angola), about 140 km from shore in 1400 meter water-depth. It was the second major discovery out of 15 made in the block 17 operated by Total. The Dalia Umbilical, Flow lines and Risers EPCI Contract was awarded in 2003. The sea-line network to connect and control the 71 wells and 9 manifolds consist of the following: 40 km of insulated pipe in pipe (12 inches into 17 inches) production flow lines; 45 km of 12 inches water and gas injection lines; 6 off 1.7 km flexible water and gas injection risers; 8 off 1.65 km flexible Integrated Production Bundle (IPB) risers; 75 km of control umbilicals. The flow assurance and associated insulation requirement of the production transport system was one of the main challenges of the project. With a crude temperature of 45 deg C at the wellhead and the required minimum temperature of 35 deg C on arrival at the FPSO, this problem was complex. Understanding that, due to the Joule Thompson effect of the riser gas lift, a 'built in' loss of about 5 deg C is induced and together with further losses through the sub sea pipelines, some up to 6 km long, the agreed solution was 'pipe in pipe' for the production flow lines. The innovative flexible IPB riser, incorporating gas lift and heating to keep the fluid temperature above hydrate formation zone, was the selected riser solution. The IPB is new technology for deep water, developed by Technip for Dalia, and consists of a 12 inches nominal central flexible, surrounded by layers of heat tracing cables, small bore gas lift lines, optical fibres and many insulation layers with an Overall Heat Transfer Coefficient of approximately 3,4 W/m{sup 2}K. After an earlier research and development programme, a further extensive qualification programme was conducted during the course of the project, culminating with the deep water testing phase offshore Brazil. The IPB was then approved for fabrication and installation

Model of a catalytic injection in a riser by means of gamma ray transmission measurements

Energy Technology Data Exchange (ETDEWEB)

Moura, Alex E.; Brito, Macio F.P.; Dantas, Carlos C.; Melo, Silvio B., E-mail: alex.emoura@ufpe.br, E-mail: sbm@ufpe.br [Universidade Federal de Pernambuco (DEN/UFPE), Recife, PE (Brazil); Barbosa, Enivaldo S., E-mail: Enivaldo.santos@ufcg.edu.br [Universidade Federal de Campina Grande (UFCG), PB (Brazil). Departamento de Engenharia Mecanica; Lima, Emerson A.O., E-mail: eal@poli.br [Universidade de Pernambuco, Recife, PE (Brazil). Departamento de Matematica

2015-07-01

In Gas solid process involving a solid circulation through a closed loop the knowledge of the Solids Circulation Rate (SCR) is fundamental to control and improve the operation of a circulating fluidized bed system. A valve controls the circulation rate of solids in the riser of a fluid catalytic cracking unit. Initially, to control the catalyst injection in the riser, a rotary valve controlled and measured solid flow injection, but with a limited working time. Due to the fine powder catalyst abrasive action on the valve steel axis, this device stop work. A lab made valve were design to avoiding direct contact of the catalyst with mechanical moving parts in while control solid injection in riser, but do not measure the solid flow like the rotary valve. To control the lab made device a fixed pressure measurement at riser bottom is provided by control setup which corresponds to a given mass/time solid injection. In the present work, we proposed a method to evaluate the control valve based on a non-invasive technique. With gamma ray transmission measurements, in a cross section of the pipe, we developed a model that was used in the control system of the Cold Pilot Unit (CPU). Therefore, the interaction of the gamma ray with solid flow in riser should yield the necessary information for the process control system. A first model approximation consider the solid flow rate injection and solid velocity in riser as proposed in literature. In the CPU control system a Programmable Logic Controller-PLC keeps steady state processing the airflow, pressure profile and solid flow inputs. Additionally to preexisting PLC platform, some LabVIEW algorithms were implemented to achieve a good system performance operational condition. (author)

Model of a catalytic injection in a riser by means of gamma ray transmission measurements

International Nuclear Information System (INIS)

Moura, Alex E.; Brito, Macio F.P.; Dantas, Carlos C.; Melo, Silvio B.; Barbosa, Enivaldo S.; Lima, Emerson A.O.

2015-01-01

In Gas solid process involving a solid circulation through a closed loop the knowledge of the Solids Circulation Rate (SCR) is fundamental to control and improve the operation of a circulating fluidized bed system. A valve controls the circulation rate of solids in the riser of a fluid catalytic cracking unit. Initially, to control the catalyst injection in the riser, a rotary valve controlled and measured solid flow injection, but with a limited working time. Due to the fine powder catalyst abrasive action on the valve steel axis, this device stop work. A lab made valve were design to avoiding direct contact of the catalyst with mechanical moving parts in while control solid injection in riser, but do not measure the solid flow like the rotary valve. To control the lab made device a fixed pressure measurement at riser bottom is provided by control setup which corresponds to a given mass/time solid injection. In the present work, we proposed a method to evaluate the control valve based on a non-invasive technique. With gamma ray transmission measurements, in a cross section of the pipe, we developed a model that was used in the control system of the Cold Pilot Unit (CPU). Therefore, the interaction of the gamma ray with solid flow in riser should yield the necessary information for the process control system. A first model approximation consider the solid flow rate injection and solid velocity in riser as proposed in literature. In the CPU control system a Programmable Logic Controller-PLC keeps steady state processing the airflow, pressure profile and solid flow inputs. Additionally to preexisting PLC platform, some LabVIEW algorithms were implemented to achieve a good system performance operational condition. (author)

Development of an environment for 3D visualization of riser dynamics

Energy Technology Data Exchange (ETDEWEB)

Bernardes Junior, Joao Luiz; Martins, Clovis de Arruda [Universidade de Sao Paulo (USP), SP (Brazil). Escola Politecnica]. E-mails: joao.bernardes@poli.usp.br; cmartins@usp.br

2006-07-01

This paper describes the merging of Virtual Reality and Scientific Visualization techniques in the development of Riser View, a multi platform 3D environment for real time, interactive visualization of riser dynamics. Its features, architecture, unusual collision detection algorithm and how up was customized for the project are discussed. Using Open GL through VRK, the software is able to make use of the resources available in most modern Graphics. Acceleration Hardware to improve performance. IUP/LED allows for native loo-and-feel in MS-Windows or Linux platform. The paper discusses conflicts that arise between scientific visualization and aspects such as realism and immersion, and how the visualization is prioritized. (author)

HOM power in FCC-ee cavities

CERN Document Server

Karpov, Ivan; Chapochnikova, Elena

2018-01-01

This Note summarizes the results of the power loss calculations for FCC-ee machines with 400.79 MHz cavity options. The requirements for the single-cell cavity design and for the operation with beam are obtained from the results for the high-current FCC-ee machine (Z). For other machines the power loss is sufficiently low and can be absorbed and extracted by foreseen HOM couplers.

The FCC-ee study: Progress and challenges

CERN Document Server

Koratzinos, Michael; Bogomyagkov, Anton; Boscolo, Manuela; Cook, Charlie; Doblhammer, Andreas; Härer, Bastian; Tomás, Rogelio; Levichev, Evgeny; Medina Medrano, Luis; Shatilov, Dmitry; Wienands, Ulrich; Zimmermann, Frank

The FCC (Future Circular Collider) study represents a vision for the next large project in high energy physics, comprising an 80-100 km tunnel that can house a future 100 TeV hadron collider. The study also includes a high luminosity e+e- collider operating in the centre-of-mass energy range of 90-350 GeV as a possible intermediate step, the FCC-ee. The FCC-ee aims at definitive electro-weak precision measurements of the Z, W, H and top particles, and search for rare phenomena. Although FCC-ee is based on known technology, the goal performance in luminosity and energy calibration make it quite challenging. During 2014 the study went through an exploration phase. The study has now entered its second year and the aim is to produce a conceptual design report during the next three to four years. We here report on progress since the last IPAC conference.

Luminosity Targets for FCC-hh

CERN Document Server

Zimmermann, F.; Buffat, X.; Schulte, D.

2016-01-01

We discuss the choice of target values for the peak and integrated luminosity of a future high-energy frontier circular hadron collider (FCC-hh). We review the arguments on the physics reach of a hadron collider. Next we show that accelerator constraints will limit the beam current and the turnaround time. Taking these limits into account, we derive an expression for the ultimate integrated luminosity per year, depending on a possible pile-up limit imposed by the physics experiments. We finally benchmark our result against the planned two phases of FCC-hh [1, 2, 3

Effect of ZSM-5 on the production of reformulated gasoline. Comparison between FCC pilot plant and commercial results

International Nuclear Information System (INIS)

Lappas, A.A.; Iatridis, D.; Vasalos, I.A.; Phyxogios, G.

1999-01-01

One of the more interesting ways for production of light olefins and for minimization of Gasoline olefins is the use of catalytic additives in the FCC (fluid catalytic cracking) inventory. The most widely used additive for the FCC process is the ZSM-5 which is a shape selective zeolite. When this additive is added to FCC units, it boosts the yields of LPG's olefins at the expense of gasoline, while increasing gasoline RON. The addition of ZSM-5 offers a great flexibility to a refinery since, in a relatively simple and cheap way, it can increase the RON and produces higher yields of light olefins. For all the above reasons the last years more studies are carried out in order to investigate the effect of this additive. In study presented in this paper, main emphasis was given, for the investigation of the effect of ZSM- 5 addition on FCC product distribution and especially on gasoline olefins. Moreover, in the previous literature works the ZSM-5 influences were examined using mainly fixed bed reactors. In the present study the investigation was carried out in a FCC pilot plant. The additive was also added in a commercial FCC unit of a Greek refinery (Hellenic Aspropyrgos Refinery - HAR) and thus comparison results of commercial and pilot plant test are also presented. The above study is part of a research collaboration which exists the last 10 years between the laboratory of Environmental Fuels and hydrocarbons of Chemical Process Engineering Research Institute (LEFH/CPERI) and the main Greek refineries (HEL.PETROLEUM, Motor Oil Hellas Refinery). The target of this research collaboration is i) the development of technology for the production of reformulated fuels and hydrocarbons and ii) to assist the Greek refineries to face the new regulations for environmental friendly fuels

Application of corrosion screening tools for riser inspection

International Nuclear Information System (INIS)

Zamir Mohamed Daud; Vijayan, S.

2003-01-01

As offshore facilities approach the end of their design life, owners would like to assess the condition and integrity of plant and equipment. Detailed inspection, including non-destructive testing (NDT), are implemented and results are utilised for predictive maintenance and estimating useful remaining life. Except for risk based inspection, the extent of surface coverage required would be more compared to inspection of pre-determined spots. Risers, for example, usually have several layers of coating that prevent use of conventional techniques for inspection of corrosion. Complete coverage requires access (including removal coatings and insulation). Inspection utilising the conventional NDT tools can be very slow and expensive. However, recent advances have forwarded the use of specialised NDT techniques that were developed for inspection of corrosion under insulation (CUI). This paper details two screening inspection tools, LIXI Profiler and RTD-INCOTEST that have been applied to inspection of risers. LIXI Profiler is based on attenuation of penetrating radiation by materials, and RTD-INCOTEST is based on decay of pulsed eddy current in materials. (Author)

New tools for steel catenary risers inspection; Novas ferramentas para inspecao de risers tipo SCR

Energy Technology Data Exchange (ETDEWEB)

Camerini, Claudio Soligo; Marinho, Carla Alves; Raphael, Fabiana N.; Maia, Carlos [PETROBRAS S.A., Rio de Janeiro, RJ (Brazil); Freitas, Miguel [Pontificia Univ. Catolica do Rio de Janeiro, RJ (Brazil); Lopes, Ricardo Tadeu; Rocha, Henrique [Universidade Federal, Rio de Janeiro, RJ (Brazil). Coordenacao dos Programas de Pos-graduacao de Engenharia

2005-07-01

The Research Center of PETROBRAS and two of the Federal Brazilian Universities, PUC-Rio and UFRJ, have been developing two new projects in order to inspect risers of petroleum production. The first tool is an instrumented pig for profiling internal corrosion, having flexibility under diameter variations and independence related to thickness wall pipeline. The second one is a gammagraphy system remotely operated by ROVs, to be employed in alveoli corrosion and fatigue cracks detection in underwater pipelines. This work shows the trajectory of these two tools, describing laboratory and field tests and the future activities. (author)

Atomistically-informed dislocation dynamics in FCC crystals

International Nuclear Information System (INIS)

Martinez, E.; Marian, J.; Arsenlis, A.; Victoria, M.; Martinez, E.; Victoria, M.; Perlado, J.M.

2008-01-01

Full text of publication follows. We will present a nodal dislocation dynamics (DD) model to simulate plastic processes in fcc crystals. The model explicitly accounts for all slip systems and Burgers vectors observed in fcc systems, including stacking faults and partial dislocations. We derive simple conservation rules that describe all partial dislocation interactions rigorously and allow us to model and quantify cross-slip processes, the structure and strength of dislocation junctions, and the formation of fcc-specific structures such as stacking fault tetrahedra. The DD framework is built upon isotropic non-singular linear elasticity, and supports itself on information transmitted from the atomistic scale. In this fashion, connection between the meso and micro scales is attained self-consistently with core parameters fitted to atomistic data. We perform a series of targeted simulations to demonstrate the capabilities of the model, including dislocation reactions and dissociations and dislocation junction strength. Additionally we map the four-dimensional stress space relevant for cross-slip and relate our fundings to the plastic behaviour of' monocrystalline fcc metals. (authors)

New developments in FCC catalysis

Energy Technology Data Exchange (ETDEWEB)

Kelkar, C.P. [BASF Corporation, Iselin, NJ (United States)

2011-07-01

Fluid catalytic cracking (FCC) unit is one of the primary boiling point reduction units in the refinery that converts longer chain crude oil to useful products such as distillate, gasoline and LPG. As the quality of feedstock deteriorates, while specifications on the product side are becoming more and more stringent, the FCC unit is being severely challenged. Over the past few years BASF has introduced two new platform technologies that will assist in this challenge. This paper will present an overview of those platforms and also provide a brief update on the research underway to mitigate the current REO crisis. (orig.)

Dynamic model for a boiling water reactor

International Nuclear Information System (INIS)

Muscettola, M.

1963-07-01

A theoretical formulation is derived for the dynamics of a boiling water reactor of the pressure tube and forced circulation type. Attention is concentrated on neutron kinetics, fuel element heat transfer dynamics, and the primary circuit - that is the boiling channel, riser, steam drum, downcomer and recirculating pump of a conventional La Mont loop. Models for the steam and feedwater plant are not derived. (author)

QCD and $\\gamma\\,\\gamma$ studies at FCC-ee

CERN Document Server

Skands, Peter

2016-10-20

The Future Circular Collider (FCC) is a post-LHC project aiming at searches for physics beyond the SM in a new 80--100~km tunnel at CERN. Running in its first phase as a very-high-luminosity electron-positron collider (FCC-ee), it will provide unique possibilities for indirect searches of new phenomena through high-precision tests of the SM. In addition, by collecting tens of ab$^{-1}$ integrated luminosity in the range of center-of-mass energies $\\sqrt{s}$~=90--350~GeV, the FCC-ee also offers unique physics opportunities for precise measurements of QCD phenomena and of photon-photon collisions through, literally, billions of hadronic final states as well as unprecedented large fluxes of quasireal $\\gamma$'s radiated from the $\\rm e^+e^-$ beams. We succinctly summarize the FCC-ee perspectives for high-precision extractions of the QCD coupling, for detailed analyses of parton radiation and fragmentation, and for SM and BSM studies through $\\gamma\\gamma$ collisions.

Spectral fatigue analysis of a tensioned riser compliant tower

NARCIS (Netherlands)

Karadeniz, H.; Vrouwenvelder, A.C.W.M.; Shi, C.

1998-01-01

In this paper, the conceptual Tensioned Riser Compliant Tower (TRCT) structure of the Shell Oil, which is developed for a region of approximately 600 meter water depth of the West of Shetlands in the North Sea, is analyzed by using the SAPOS program of the Delft University of Technology. The fatigue

Helical wire stress analysis of unbonded flexible riser under irregular response

Science.gov (United States)

Wang, Kunpeng; Ji, Chunyan

2017-06-01

A helical wire is a critical component of an unbonded flexible riser prone to fatigue failure. The helical wire has been the focus of much research work in recent years because of the complex multilayer construction of the flexible riser. The present study establishes an analytical model for the axisymmetric and bending analyses of an unbonded flexible riser. The interlayer contact under axisymmetric loads in this model is modeled by setting radial dummy springs between adjacent layers. The contact pressure is constant during the bending response and applied to determine the slipping friction force per unit helical wire. The model tracks the axial stress around the angular position at each time step to calculate the axial force gradient, then compares the axial force gradient with the slipping friction force to judge the helical wire slipping region, which would be applied to determine the bending stiffness for the next time step. The proposed model is verified against the experimental data in the literature. The bending moment-curvature relationship under irregular response is also qualitatively discussed. The stress at the critical point of the helical wire is investigated based on the model by considering the local flexure. The results indicate that the present model can well simulate the bending stiffness variation during irregular response, which has significant effect on the stress of helical wire.

Reconstruction of Twist Torque in Main Parachute Risers

Science.gov (United States)

Day, Joshua D.

2015-01-01

The reconstruction of twist torque in the Main Parachute Risers of the Capsule Parachute Assembly System (CPAS) has been successfully used to validate CPAS Model Memo conservative twist torque equations. Reconstruction of basic, one degree of freedom drop tests was used to create a functional process for the evaluation of more complex, rigid body simulation. The roll, pitch, and yaw of the body, the fly-out angles of the parachutes, and the relative location of the parachutes to the body are inputs to the torque simulation. The data collected by the Inertial Measurement Unit (IMU) was used to calculate the true torque. The simulation then used photogrammetric and IMU data as inputs into the Model Memo equations. The results were then compared to the true torque results to validate the Model Memo equations. The Model Memo parameters were based off of steel risers and the parameters will need to be re-evaluated for different materials. Photogrammetric data was found to be more accurate than the inertial data in accounting for the relative rotation between payload and cluster. The Model Memo equations were generally a good match and when not matching were generally conservative.

Insulating fcc YH

International Nuclear Information System (INIS)

Molen, S. J. van der; Nagengast, D. G.; Gogh, A. T. M. van; Kalkman, J.; Kooij, E. S.; Rector, J. H.; Griessen, R.

2001-01-01

We study the structural, optical, and electrical properties of Mg z Y 1-z switchable mirrors upon hydrogenation. It is found that the alloys disproportionate into essentially pure YH 3-δ and MgH 2 with the crystal structure of YH 3-δ dependent on the Mg concentration z. For 0 3-δ are observed, whereas for z≥0.1 only cubic YH 3-δ is present. Interestingly, cubic YH 3-δ is expanded compared to YH 2 , in disagreement with theoretical predictions. From optical and electrical measurements we conclude that cubic YH 3-δ is a transparent insulator with properties similar to hexagonal YH 3-δ . Our results are inconsistent with calculations predicting fcc YH 3-δ to be metallic, but they are in good agreement with recent GW calculations on both hcp and fcc YH 3 . Finally, we find an increase in the effective band gap of the hydrided Mg z Y 1-z alloys with increasing z. Possibly this is due to quantum confinement effects in the small YH 3 clusters

Regeneration of Hydrotreating and FCC Catalysts

Energy Technology Data Exchange (ETDEWEB)

CM Wai; JG Frye; JL Fulton; LE Bowman; LJ Silva; MA Gerber

1999-09-30

Hydrotreating, hydrocracking, and fluid catalytic cracking (FCC) catalysts are important components of petroleum refining processes. Hydrotreating and hydrocracking catalysts are used to improve the yield of high-quality light oil fractions from heavier crude oil and petroleum feedstocks containing high levels of impurities. FCC catalysts improve the yield of higher octane gasoline from crude oil. Residuum hydrotreating and cracking catalysts are susceptible to irreversible deactivation caused by adsorption of sulfur and by metals impurities, such as vanadium and nickel. The gradual buildup of these impurities in a hydrotreating catalyst eventually plugs the pores and deactivates it. Nickel and vanadium adversely affect the behavior of cracking catalysts, reducing product yield and quality. Replacing deactivated catalysts represents a significant cost in petroleum refining. Equally important are the costs and potential liabilities associated with treating and disposing spent catalysts. For example, recent US Environmental Protection Agency rulings have listed spent hydrotreating and hydrorefining catalysts as hazardous wastes. FCC catalysts, though more easily disposed of as road-base or as filler in asphalt and cement, are still an economic concern mainly because of the large volumes of spent catalysts generated. New processes are being considered to increase the useful life of catalysts or for meeting more stringent disposal requirements for spent catalysts containing metals. This report discusses a collaborative effort between Pacific Northwest National Laboratory (PNNL) and Phillips Petroleum, Inc., to identify promising chemical processes for removing metals adhered to spent hydrodesulfurization (HDS, a type of hydrotreating catalyst) and FCC catalysts. This study, conducted by PNNL, was funded by the US Department of Energy's Bartlesville Project Office. Fresh and spent catalysts were provided by Phillips Petroleum. The FCC catalyst was a rare

Mathematics of flexible risers including pressure and internal flow affects

Energy Technology Data Exchange (ETDEWEB)

Seyed, F.B. (John Brown Engineers and Constructors Ltd., London (GB)); Patel, M.H. (University Coll., London (GB). Dept. of Mechanical Engineering)

1992-01-01

Derivations are presented for calculation of pressure and internal flow induced forces on flexible risers and other curved pipes using a mathematically rigorous approach. Approximate and exact methods are presented for calculation of pressure forces on straight and curved pipes in two dimensions. The mathematical identity of these equations with those for effective tension is illustrated. The force arising from the flow of an internal fluid of constant density is then calculated and combined with those for pressure forces in derivation of the catenary equations including pressure and internal flow terms. It is shown that internal flow contributes a new term to the expression for effective tension. These governing equations are then reduced for the specific cases of simple catenary, steep-S, lazy-S, steep-wave and lazy-wave risers. In each case, the solution method has been presented and the governing equilibrium and geometric compatability conditions cited. (author).

Precision measurements of the top quark couplings at the FCC

CERN Document Server

AUTHOR|(CDS)2051271

2015-01-01

The design study of the Future Circular Colliders (FCC) in a 100-km ring in the Geneva area has started at CERN at the beginning of 2014, as an option for post-LHC particle accelerators. The study has an emphasis on proton-proton and electron-positron high-energy frontier machines. In the current plans, the first step of the FCC physics programme would exploit a high-luminosity e+e- collider called FCC-ee, with centre-of-mass energies ranging from below the Z pole to the t-tbar threshold and beyond, followed by 100\\,TeV proton-proton collisions as ultimate goal. When combined, these two steps offer a large palette of complementary measurements and sensitivity for new physics. In particular, the association of the FCC-ee and the FCC-hh allows measurements of the top-quark electroweak and Yukawa couplings to be performed with unrivaled precision.

Inelastic neutron scattering from high-density fcc 4He

International Nuclear Information System (INIS)

Thomlinson, W.; Eckert, J.; Shirane, G.

1978-01-01

The phonon dispersion relations in high-density crystals of fcc 4 He have been measured along high-symmetry directions by the neutron-inelastic-scattering technique. A recent study of the lattice dynamics of fcc 4 He by Eckert et al. has been extended to cover the fcc phase diagram at pressures below 5 kbar. Molar volumes of 9.03, 9.43, and 9.97 cm 3 /mole have been studied in the temperature range from near the melting curve to near the fcc-hcp transition line. The phonon dispersion relations are in good agreement with a first-order self-consistent phonon theory calculation by Goldman. The observed phonon-group line shapes at large energy and momentum transfers show evidence for multiphonon scattering in agreement with calculations by Glyde. Eckert et al. reported extremely large anharmonic isochoric temperature shifts of the phonon energies. The present work studied the shifts as a function of molar volume and temperature. Mode-Grueneisen-parameter dispersion curves have been measured using the present data and earlier measurements at lower density in the fcc phase by Traylor et al. Macroscopic Grueneisen parameters have been calculated from the phonon density of states obtained from the data

Refining fault slip rates using multiple displaced terrace risers-An example from the Honey Lake fault, NE California, USA

Science.gov (United States)

Gold, Ryan D.; Briggs, Richard W.; Crone, Anthony J.; DuRoss, Christopher B.

2017-11-01

Faulted terrace risers are semi-planar features commonly used to constrain Quaternary slip rates along strike-slip faults. These landforms are difficult to date directly and therefore their ages are commonly bracketed by age estimates of the adjacent upper and lower terrace surfaces. However, substantial differences in the ages of the upper and lower terrace surfaces (a factor of 2.4 difference observed globally) produce large uncertainties in the slip-rate estimate. In this investigation, we explore how the full range of displacements and bounding ages from multiple faulted terrace risers can be combined to yield a more accurate fault slip rate. We use 0.25-m cell size digital terrain models derived from airborne lidar data to analyze three sites where terrace risers are offset right-laterally by the Honey Lake fault in NE California, USA. We use ages for locally extensive subhorizontal surfaces to bracket the time of riser formation: an upper surface is the bed of abandoned Lake Lahontan having an age of 15.8 ± 0.6 ka and a lower surface is a fluvial terrace abandoned at 4.7 ± 0.1 ka. We estimate lateral offsets of the risers ranging between 6.6 and 28.3 m (median values), a greater than fourfold difference in values. The amount of offset corresponds to the riser's position relative to modern stream meanders: the smallest offset is in a meander cutbank position, whereas the larger offsets are in straight channel or meander point-bar positions. Taken in isolation, the individual terrace-riser offsets yield slip rates ranging from 0.3 to 7.1 mm/a. However, when the offset values are collectively assessed in a probabilistic framework, we find that a uniform (linear) slip rate of 1.6 mm/a (1.4-1.9 mm/a at 95% confidence) can satisfy the data, within their respective uncertainties. This investigation demonstrates that integrating observations of multiple offset elements (crest, midpoint, and base) from numerous faulted and dated terrace risers at closely spaced

An atomic-scale model of fcc crystal-growth

Energy Technology Data Exchange (ETDEWEB)

Waal, B.W. van de (Technische Hogeschool Twente, Enschede (Netherlands). Dept. of Physics)

1991-01-01

Nearly perfect fcc growth may be simulated by the application of a simple growth-algorithm - only sites that are at least 4-coordinated are occupied - to a selected seed. The seed is a 22-atom cluster, being the smallest close-packed structure with two crossing stacking-faults. The stacking-faults produce active surface-sites, that can not be exhausted by occupation; they are arranged in non-vanishing steps, similar to those produced by screw-dislocations. The algorithm prevents further stacking-faults, and ensures ABC-stacking of close-packed (111)-layers, characteristic of the fcc structure. The same algorithm would not produce further growth of perfect fcc clusters or of Mackay icosahedra. It is proposed that the ability to grow fast under near-equilibrium conditions is a better criterion to select clusters as precursors of the bulk-structure than their cohesive energy. The crystal structure problem of the rare gases - why fcc, not hcp - is discussed in connection with the apparent impossibility to simulate hcp growth by an analogous procedure. (orig.).

Nanosized f.c.c. thallium inclusions in aluminium

International Nuclear Information System (INIS)

Johnson, E.; Johansen, A.; Thoft, N.B.; Andersen, H.H.; Sarholt-Kristensen, L.

1993-01-01

Ion implantation of pure aluminium with thallium induces the formation of nanosized crystalline inclusions of thallium with a f.c.c. structure. The size of the inclusions depends on the implantation conditions and subsequent annealing treatments and is typically in the range from 1 to 10 nm. The inclusions are aligned topotactically with the aluminium matrix with a cube-cube orientation relationship and they have a truncated octahedral shape bounded by {111} and {001} planes. The lattice parameter of the f.c.c. thallium inclusions is 0.484 ± 0.002 nm, which is slightly but significantly larger than in the high-pressure f.c.c. thallium phase known to be stable above 3.8 GPa. (Author)

Numerical investigation on effect of riser diameter and inclination on system parameters in a two-phase closed loop thermosyphon solar water heater

International Nuclear Information System (INIS)

Aung, Nay Zar; Li, Songjing

2013-01-01

Highlights: • Optimum inclination for maximum heat flux changes with latitude of location. • Optimum inclination for maximum heat flux also changes local solar time. • Maximum flow rate increases with increasing of riser tube size. • Maximum mass flow rate is obtained at different inclinations for different risers. • Length of two-phase region depends on inclination angles but not riser tube size. - Abstract: In this work, the effect of riser diameter and its inclination angle on system parameters in a two-phase closed loop thermosyphon solar water heater has been numerically investigated. Here, receivable heat flux by the collector, circulating mass flow rate, driving pressure, total pressure drop, heat transfer coefficient in risers and collector efficiency are defined as system parameters. For this aim, a model of two-phase thermosyphon solar water heater that is acceptable for various inclinations is presented and variations of riser diameter and inclination are considered. The riser tube size is varied from 1.25 cm to 2.5 cm with inclination range 2–75°. The system absolute pressure is set as 3567 Pa and water is chosen as working fluid. The results show that higher inclination angle is required for higher latitude location to obtain maximum solar heat flux. At local solar noon of 21.996 north latitude, the optimum inclination angle increases in the range of 24–44° with increasing of riser diameter giving maximum circulating mass flow rate from 0.02288 kg/s to 0.03876 kg/s. The longer two-phase heat transfer characteristics can be obtained at smaller inclination angles and mass flow rate for all riser tube sizes. Therefore, it is observed that the optimum inclination angles and diameters for solar heat flux, circulating mass flow rate and heat transfer coefficient in two-phase thermosyphon systemdo not coincide. From this work, better understanding and useful information are provided for constructing two-phase thermosyphon solar heaters

Laboratory measurements of vortex- and wake-induced vibrations of a tandem arrangement of two flexible risers

Science.gov (United States)

Liu, Huai-zeng; Wang, Fei; Jiang, Guo-sheng; Guo, Hai-yan; Li, Xiao-min

2016-03-01

The dynamic response of two flexible model risers in tandem arrangement immersed in a stepped current was analyzed. The risers, with an external diameter of 20 mm and a total length of 6200 mm, had an aspect ratio of 310. They were hinged to the support structure at the center-to-center distances away 3-12 times the external diameter. The top 1200 mm was exposed to a uniform current at a speed which was up to 0.9 m/s (the Reynolds number was 18000) and the rest in still water. The dynamic responses, which were obtained through the Fiber Bragg Grating strain gauges mounted on the surface, were analyzed by studying the cross-flow amplitudes and modal weights. The cross-flow vibration were observed up to the third mode, and the modal transformation from the second mode to the third mode was clearly observed. The experiment confirmed that the typical vortex-induced vibration (VIV) had occurred on the up-stream riser. But for the down-stream riser, the main excitation mechanism was wake-induced vibration (WIV). The modal transformation of WIV was more complex than that of VIV, which might be helpful for other researchers to study the interference effect.

Flexible Riser Monitoring Using Hybrid Magnetic/Optical Strain Gage Techniques through RLS Adaptive Filtering

Directory of Open Access Journals (Sweden)

Daniel Pipa

2010-01-01

Full Text Available Flexible riser is a class of flexible pipes which is used to connect subsea pipelines to floating offshore installations, such as FPSOs (floating production/storage/off-loading unit and SS (semisubmersible platforms, in oil and gas production. Flexible risers are multilayered pipes typically comprising an inner flexible metal carcass surrounded by polymer layers and spiral wound steel ligaments, also referred to as armor wires. Since these armor wires are made of steel, their magnetic properties are sensitive to the stress they are subjected to. By measuring their magnetic properties in a nonintrusive manner, it is possible to compare the stress in the armor wires, thus allowing the identification of damaged ones. However, one encounters several sources of noise when measuring electromagnetic properties contactlessly, such as movement between specimen and probe, and magnetic noise. This paper describes the development of a new technique for automatic monitoring of armor layers of flexible risers. The proposed approach aims to minimize these current uncertainties by combining electromagnetic measurements with optical strain gage data through a recursive least squares (RLSs adaptive filter.

Application of Zeolitic Additives in the Fluid Catalytic Cracking (FCC

Directory of Open Access Journals (Sweden)

A. Nemati Kharat

2013-06-01

Full Text Available Current article describes application of zeolites in fluid catalytic cracking (FCC. The use of several zeolitic additives for the production light olefins and reduction of pollutants is described. Application of zeolites as fluid catalytic cracking (FCC catalysts and additives due to the presence of active acid sites in the zeolite framework  increase the formation of desired cracking products (i.e., olefin and branched products  in the FCC unit.

Ab initio lattice stability of fcc and hcp Fe-Mn random alloys

International Nuclear Information System (INIS)

Gebhardt, T; Music, D; Hallstedt, B; Schneider, J M; Ekholm, M; Abrikosov, I A; Vitos, L

2010-01-01

We have studied the lattice stability of face centred cubic (fcc) versus hexagonal close packed (hcp) Fe-Mn random alloys using ab initio calculations. In the calculations we considered the antiferromagnetic order of local moments, which for fcc alloys models the magnetic configuration of this phase at room temperature (below its Neel temperature) as well as their complete disorder, corresponding to paramagnetic fcc and hcp alloys. For both cases, the results are consistent with our thermodynamic calculations, obtained within the Calphad approach. For the room temperature magnetic configuration, the cross-over of the total energies of the hcp phase and the fcc phase of Fe-Mn alloys is at the expected Mn content, whereas for the magnetic configuration above the fcc Neel temperature, the hcp lattice is more stable within the whole composition range studied. The increase of the total energy difference between hcp and antiferromagnetic fcc due to additions of Mn as well as the stabilizing effect of antiferromagnetic ordering on the fcc phase are well displayed. These results are of relevance for understanding the deformation mechanisms of these random alloys.

Ab initio lattice stability of fcc and hcp Fe-Mn random alloys

Energy Technology Data Exchange (ETDEWEB)

Gebhardt, T; Music, D; Hallstedt, B; Schneider, J M [Materials Chemistry, RWTH Aachen University, D-52056 Aachen (Germany); Ekholm, M; Abrikosov, I A [Department of Physics, Chemistry and Biology (IFM), Linkoeping University, SE-581 83 Linkoeping (Sweden); Vitos, L, E-mail: gebhardt@mch.rwth-aachen.d [Department of Materials Science and Engineering, Applied Materials Physics, oyal Institute of Technology, SE-10044 Stockholm (Sweden)

2010-07-28

We have studied the lattice stability of face centred cubic (fcc) versus hexagonal close packed (hcp) Fe-Mn random alloys using ab initio calculations. In the calculations we considered the antiferromagnetic order of local moments, which for fcc alloys models the magnetic configuration of this phase at room temperature (below its Neel temperature) as well as their complete disorder, corresponding to paramagnetic fcc and hcp alloys. For both cases, the results are consistent with our thermodynamic calculations, obtained within the Calphad approach. For the room temperature magnetic configuration, the cross-over of the total energies of the hcp phase and the fcc phase of Fe-Mn alloys is at the expected Mn content, whereas for the magnetic configuration above the fcc Neel temperature, the hcp lattice is more stable within the whole composition range studied. The increase of the total energy difference between hcp and antiferromagnetic fcc due to additions of Mn as well as the stabilizing effect of antiferromagnetic ordering on the fcc phase are well displayed. These results are of relevance for understanding the deformation mechanisms of these random alloys.

First-principles study of ternary fcc solution phases from special quasirandom structures

International Nuclear Information System (INIS)

Shin Dongwon; Wang Yi; Liu Zikui; Walle, Axel van de

2007-01-01

In the present work, ternary special quasirandom structures (SQSs) for a fcc solid solution phase are generated at different compositions, x A =x B =x C =(1/3) and x A =(1/2), x B =x C =(1/4), whose correlation functions are satisfactorily close to those of a random fcc solution. The generated SQSs are used to calculate the mixing enthalpy of the fcc phase in the Ca-Sr-Yb system. It is observed that first-principles calculations of all the binary and ternary SQSs in the Ca-Sr-Yb system exhibit very small local relaxation. It is concluded that the fcc ternary SQSs can provide valuable information about the mixing behavior of the fcc ternary solid solution phase. The SQSs presented in this work can be widely used to study the behavior of ternary fcc solid solutions

Physics case of FCC-ee

CERN Document Server

d'Enterria, David

2016-01-01

The physics case for electron-positron beams at the Future Circular Collider (FCC-ee) is succinctly summarized. The FCC-ee core program involves $e^+e^-$ collisions at $\\sqrt{s}$ = 90, 160, 240, and 350 GeV with multi-ab$^{-1}$ integrated luminosities, yielding about 10$^{12}$ Z bosons, 10$^{8}$ W$^+$W$^-$ pairs, 10$^{6}$ Higgs bosons and 4$\\cdot$10$^{5}$ $t\\bar{t}$ pairs per year. The huge luminosities combined with $\\cal{100}$ keV knowledge of the c.m. energy will allow for Standard Model studies at unrivaled precision. Indirect constraints on new physics can thereby be placed up to scales $\\Lambda_{_{\\rm NP}} \\approx$ 7 and 100 TeV for particles coupling respectively to the Higgs and electroweak bosons.

Electronic structure and superconductivity of fcc Cr

International Nuclear Information System (INIS)

Xu, J.; Freeman, A.J.; Jarlborg, T.; Brodsky, M.B.

1984-01-01

Results of self-consistent electronic structure calculations are reported for metastable fcc Cr metal. Unlike the case of bcc Cr which has E/sub F/ at a minimum in the density of states (DOS), the DOS at E/sub F/ in fcc Cr is at a peak making this one of the higher-DOS metals with the fcc structure (e.g., comparable with that of Ni and Pt). A calculated Stoner factor of 0.82 indicates that ferromagnetic ordering is not expected. Calculations of the electron-phonon coupling parameter lambda and superconducting transition temperature T/sub c/ were made using the rigid-ion approximation and strong-coupling theory with various estimates of the (unknown) phonon contribution. We conclude that T/sub c/'sroughly-equal2.5 K are reasonable, although they are substantially smaller than the T/sub c/roughly-equal10 K derived from measurements on Au-Cr-Au sandwiches

Numerical simulations of vortex-induced vibrations of a flexible riser with different aspect ratiosin uniform and shear currents

Science.gov (United States)

Duanmu, Yu; Zou, Lu; Wan, De-cheng

2017-12-01

This paper aimed at describing numerical simulations of vortex-induced vibrations (VIVs) of a long flexible riser with different length-to-diameter ratio (aspect ratio) in uniform and shear currents. Three aspect ratios were simulated: L/D = 500, 750 and 1 000. The simulation was carried out by the in-house computational fluid dynamics (CFD) solver viv-FOAM-SJTU developed by the authors, which was coupled with the strip method and developed on the OpenFOAM platform. Moreover, the radial basis function (RBF) dynamic grid technique is applied to the viv-FOAM-SJTU solver to simulate the VIV in both in-line (IL) and cross-flow (CF) directions of flexible riser with high aspect ratio. The validation of the benchmark case has been completed. With the same parameters, the aspect ratio shows a significant influence on VIV of a long flexible riser. The increase of aspect ratio exerted a strong effect on the IL equilibrium position of the riser while producing little effect on the curvature of riser. With the aspect ratio rose from 500 to 1 000, the maximum IL mean displacement increased from 3 times the diameter to 8 times the diameter. On the other hand, the vibration mode of the riser would increase with the increase of aspect ratio. When the aspect ratio was 500, the CF vibration was shown as a standing wave with a 3rd order single mode. When the aspect ratio was 1 000, the modal weights of the 5th and 6th modes are high, serving as the dominant modes. The effect of the flow profile on the oscillating mode becomes more and more apparent when the aspect ratio is high, and the dominant mode of riser in shear flow is usually higher than that in uniform flow. When the aspect ratio was 750, the CF oscillations in both uniform flow and shear flow showed multi-mode vibration of the 4th and 5th mode. While, the dominant mode in uniform flow is the 4th order, and the dominant mode in shear flow is the 5th order.

FCC-hh Hadron Collider - Parameter Scenarios and Staging Options

CERN Document Server

Benedikt, Michael; Schulte, Daniel; Zimmermann, F; Syphers, M J

2015-01-01

FCC-hh is a proposed future energy-frontier hadron collider, based on dipole magnets with a field around 16 T installed in a new tunnel with a circumference of about 100 km, which would provide proton collisions at a centre-of-mass energy of 100 TeV, as well as heavy-ion collisions at the equivalent energy. The FCC-hh should deliver a high integrated proton-proton luminosity at the level of several 100 fb−1 per year, or more. The challenges for operating FCC-hh with high beam current and at high luminosity include the heat load from synchrotron radiation in a cold environment, the radiation from collision debris around the interaction region, and machine protection. In this paper, starting from the FCC-hh design baseline parameters we explore different approaches for increasing the integrated luminosity, and discuss the impact of key individual pa- rameters, such as the turnaround time. We also present some injector considerations and options for early hadron-collider operation.

Dynamic optimization of a FCC converter unit: numerical analysis

Directory of Open Access Journals (Sweden)

E. Almeida Nt

2011-03-01

Full Text Available Fluidized-bed Catalytic Cracking (FCC is a process subject to frequent variations in the operating conditions (including feed quality and feed rate. The production objectives usually are the maximization of LPG and gasoline production. This fact makes the FCC converter unit an excellent opportunity for real-time optimization. The present work aims to apply a dynamic optimization in an industrial FCC converter unit, using a mechanistic dynamic model, and to carry out a numerical analysis of the solution procedure. A simultaneous approach was used to discretize the system of differential-algebraic equations and the resulting large-scale NLP problem was solved using the IPOPT solver. This study also does a short comparison between the results obtained by a potential dynamic real-time optimization (DRTO against a possible steady-state real-time optimization (RTO application. The results demonstrate that the application of dynamic real-time optimization of a FCC converter unit can bring significant benefits in production.

Economic Analysis on Direct Use of Spent Pressurized Water Reactor Fuel in CANDU Reactors - IV: DUPIC Fuel Cycle Cost

International Nuclear Information System (INIS)

Ko, Won Il; Choi, Hangbok; Yang, Myung Seung

2001-01-01

This study examines the economics of the DUPIC fuel cycle using unit costs of fuel cycle components estimated based on conceptual designs. The fuel cycle cost (FCC) was calculated by a deterministic method in which reference values of fuel cycle components are used. The FCC was then analyzed by a Monte Carlo simulation to get the uncertainty of the FCC associated with the unit costs of the fuel cycle components. From the deterministic analysis on the equilibrium fuel cycle model, the DUPIC FCC was estimated to be 6.21 to 6.34 mills/kW.h for DUPIC fuel options, which is a little smaller than that of the once-through FCC by 0.07 to 0.27 mills/kW.h. Considering the uncertainty (0.40 to 0.44 mills/kW.h) of the FCC estimated by the Monte Carlo simulation method, the cost difference between the DUPIC and once-through fuel cycle is negligible. On the other hand, the material balance calculation has shown that the DUPIC fuel cycle can save natural uranium resources by ∼20% and reduce the spent fuel arising by ∼65% compared with the once-through fuel cycle. In conclusion, the DUPIC fuel cycle is comparable with the once-through fuel cycle from the viewpoint of FCC. In the future, it should be important to consider factors such as the environmental benefit owing to natural uranium savings, the capability of reusing spent pressurized water reactor fuel, and the safeguardability of the fuel cycle when deciding on an advanced nuclear fuel cycle option

The impact of a grain of sand: increasing production speed in flexible risers generates significant savings in gas production

NARCIS (Netherlands)

Bokhorst, E. van; Blokland, H.

2012-01-01

Deep-sea oil and gas production normally involves the use of flexible risers that comprise a metal carcass with a large number of enveloping layers that safeguard the integrity of the pipe system. The flexible risers are hung from a floating platform and may be supported by several floating buoys to

Beam Dynamics Challenges for FCC-ee

CERN Document Server

AUTHOR|(SzGeCERN)442987; Benedikt, Michael; Oide, Katsunobu; Bogomyagkov, Anton; Levichev, Evgeny; Migliorati, Mauro; Wienands, Uli

2015-01-01

The goals of FCC-ee include reaching luminosities of up to a few 1036 cm-2s-1 per interaction point at the Z pole or some 1034 cm-2s-1 at the ZH production peak, and pushing the beam energy up to ≥175 GeV, in a ring of 100 km circumference, with a total synchrotron-radiation power not exceeding 100 MW. A parameter baseline as well as high-luminosity crab-waist options were described in [1] and [2], respectively. The extremely high luminosity and resulting short beam lifetime (due to radiative Bhabha scattering) are sustained by top-up injection. The FCC-ee design status and typical beam parameters for different modes of operation are reported in [3]. One distinct feature of the FCC-ee design is its conception as a double ring, with separate beam pipes for the two counter-rotating (electron and positron) beams, resembling, in this aspect, the high-luminosity B factories PEP-II, KEKB and SuperKEKB as well as the LHC. The two separate rings do not only permit operation with a large number of bunches, up to a f...

Impact of FCC regenerator design in the NOx emissions

Energy Technology Data Exchange (ETDEWEB)

Pereira, Hugo Borges; Sandes, Emanuel Freire; Gilbert, William Richard; Roncolatto, Rodolfo Eugenio; Gobbo, Rodrigo; Casavechia, Luiz Carlos; Candido, William Victor Carlos [Petroleo Brasileiro S.A. (PETROBRAS), Rio de Janeiro, RJ (Brazil); Bridi, Patricia Elaine [Possebon Engenharia, Sao Mateus do Sul, PR (Brazil)

2012-07-01

Fluid Catalytic Cracking (FCC) is the main point source of NOx in the refinery and it is responsible for at least 20% of the total NOx emissions from the refineries. The thermal NOx formation in the FCC regenerator is negligible. However, half of the feed nitrogen is converted to coke, and is burned in the regenerator. The majority of coke nitrogen is reduced to N2 and less than 10% is converted to NOx. This number may vary significantly with the oxygen excess in the flue gas and other operational conditions. With the purpose of evaluating the impact of different regenerator designs in NOx formation, several tests were carried out in the PETROBRAS FCC prototype unit. The test unit is equipped with adiabatic insulation and a CO boiler, allowing it to reproduce the heat balance of a commercial FCC and to operate either in full combustion or partial combustion. Two different designs of FCC regenerators were evaluated: single stage regenerator (the existing configuration) and two stage regenerator, with the catalyst bed divided into two sections by a structured packing baffle. It was observed in the tests that the combustion regime had a very strong effect on NOx formation. In full combustion, the effect of the FCC operating variables: excess oxygen, combustion promoter content in catalyst and regenerator design could be identified. The two stage configuration was capable of decreasing NOx emissions by 30%. In partial combustion, the effect of the CO-boiler variables on NOx emissions was overwhelming, but the use of the structured packing baffle was able to improve the catalyst regeneration.(author)

A state space approach for the eigenvalue problem of marine risers

KAUST Repository

Alfosail, Feras

2017-10-05

A numerical state-space approach is proposed to examine the natural frequencies and critical buckling limits of marine risers. A large axial tension in the riser model causes numerical limitations. These limitations are overcome by using the modified Gram–Schmidt orthonormalization process as an intermediate step during the numerical integration process with the fourth-order Runge–Kutta scheme. The obtained results are validated against those obtained with other numerical methods, such as the finite-element, Galerkin, and power-series methods, and are found to be in good agreement. The state-space approach is shown to be computationally more efficient than the other methods. Also, we investigate the effect of a high applied tension, a high apparent weight, and higher-order modes on the accuracy of the numerical scheme. We demonstrate that, by applying the orthonormalization process, the stability and convergence of the approach are significantly improved.

Neutron Scattering from fcc Pr and Pr3Tl

DEFF Research Database (Denmark)

Birgeneau, R. J.; Als-Nielsen, Jens Aage; Bucher, E.

1972-01-01

Elastic-neutron-scattering measurements on the singlet-ground-state ferromagnets fcc Pr and Pr3 Tl are reported. Both exhibit magnetic phase transitions, possibly to a simple ferromagnetic state at 20 and 11.6 °K, respectively. The transitions appear to be of second order although that in fcc Pr...

Experimental Plan for Crystal Accumulation Studies in the WTP Melter Riser

Energy Technology Data Exchange (ETDEWEB)

Miller, D. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Fowley, M. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

2015-04-28

This experimental plan defines crystal settling experiments to be in support of the U.S. Department of Energy – Office of River Protection crystal tolerant glass program. The road map for development of crystal-tolerant high level waste glasses recommends that fluid dynamic modeling be used to better understand the accumulation of crystals in the melter riser and mechanisms of removal. A full-scale version of the Hanford Waste Treatment and Immobilization Plant (WTP) melter riser constructed with transparent material will be used to provide data in support of model development. The system will also provide a platform to demonstrate mitigation or recovery strategies in off-normal events where crystal accumulation impedes melter operation. Test conditions and material properties will be chosen to provide results over a variety of parameters, which can be used to guide validation experiments with the Research Scale Melter at the Pacific Northwest National Laboratory, and that will ultimately lead to the development of a process control strategy for the full scale WTP melter. The experiments described in this plan are divided into two phases. Bench scale tests will be used in Phase 1 (using the appropriate solid and fluid simulants to represent molten glass and spinel crystals) to verify the detection methods and analytical measurements prior to their use in a larger scale system. In Phase 2, a full scale, room temperature mockup of the WTP melter riser will be fabricated. The mockup will provide dynamic measurements of flow conditions, including resistance to pouring, as well as allow visual observation of crystal accumulation behavior.

Stacking fault density and bond orientational order of fcc ruthenium nanoparticles

Science.gov (United States)

Seo, Okkyun; Sakata, Osami; Kim, Jae Myung; Hiroi, Satoshi; Song, Chulho; Kumara, Loku Singgappulige Rosantha; Ohara, Koji; Dekura, Shun; Kusada, Kohei; Kobayashi, Hirokazu; Kitagawa, Hiroshi

2017-12-01

We investigated crystal structure deviations of catalytic nanoparticles (NPs) using synchrotron powder X-ray diffraction. The samples were fcc ruthenium (Ru) NPs with diameters of 2.4, 3.5, 3.9, and 5.4 nm. We analyzed average crystal structures by applying the line profile method to a stacking fault model and local crystal structures using bond orientational order (BOO) parameters. The reflection peaks shifted depending on rules that apply to each stacking fault. We evaluated the quantitative stacking faults densities for fcc Ru NPs, and the stacking fault per number of layers was 2-4, which is quite large. Our analysis shows that the fcc Ru 2.4 nm-diameter NPs have a considerably high stacking fault density. The B factor tends to increase with the increasing stacking fault density. A structural parameter that we define from the BOO parameters exhibits a significant difference from the ideal value of the fcc structure. This indicates that the fcc Ru NPs are highly disordered.

Workshop summary, future prospects and FCC-ee impact on $\\alpha_s$

CERN Document Server

d'Enterria, David

2015-01-01

The workshop on “High-precision α s measurements from LHC to FCC-ee” –organized in the con- text of the preparation of the Future Circular Collider (FCC) Conceptual Design Report, within the FCC-e + e − “QCD and photon-photon” physics working group activities– discussed the latest advances in the measurement of the strong interaction coupling α s . The meeting brought together leading experts in the field to explore in depth recent theoretical and experimental developments on the determination of α s , new ways to measure this coupling in lepton-lepton, lepton-hadron and hadron-hadron collisions, and in particular the improvements expected at the proposed Future Circular Collider e + e − (FCC-ee) facility.

Stochastic dynamic analysis of marine risers considering Gaussian system uncertainties

Science.gov (United States)

Ni, Pinghe; Li, Jun; Hao, Hong; Xia, Yong

2018-03-01

This paper performs the stochastic dynamic response analysis of marine risers with material uncertainties, i.e. in the mass density and elastic modulus, by using Stochastic Finite Element Method (SFEM) and model reduction technique. These uncertainties are assumed having Gaussian distributions. The random mass density and elastic modulus are represented by using the Karhunen-Loève (KL) expansion. The Polynomial Chaos (PC) expansion is adopted to represent the vibration response because the covariance of the output is unknown. Model reduction based on the Iterated Improved Reduced System (IIRS) technique is applied to eliminate the PC coefficients of the slave degrees of freedom to reduce the dimension of the stochastic system. Monte Carlo Simulation (MCS) is conducted to obtain the reference response statistics. Two numerical examples are studied in this paper. The response statistics from the proposed approach are compared with those from MCS. It is noted that the computational time is significantly reduced while the accuracy is kept. The results demonstrate the efficiency of the proposed approach for stochastic dynamic response analysis of marine risers.

Stress induced martensitic transformation from bcc to fcc in Ag-Zn

International Nuclear Information System (INIS)

Takezawa, K.; Akamatsu, R.; Marukawa, K.

1995-01-01

The martensitic transformation in Ag-Zn alloys of low-Zn content has been studied by optical and electron microscopic observations and by tensile tests. The β 1 phase of B2 structure transforms to the thermo-elastic martensite having 9R structure similar to Cu-based alloys upon cooling to temperature below Ms. When the β 1 phase is stretched at room temperature, the slip deformation occurs at first and then the stress-induced martensite(SIM) of wedge-like morphology forms. The SIM has the ordered fcc structure containing micro-twins. This direct transformation from bcc to fcc is a unique feature in Ag-Zn alloys. In Cu alloys, martensites of fcc structure appear only after the second transformation from the first transformation product of 9R structure. The critical stress for the martensitic transformation and a degree of order of SIM decrease as the deformation temperature rises. In Ag-Zn alloys, the martensite of disordered fcc is thermally produced also by up-quenching to a higher temperature. In the present study, the relation between martensites of ordered and disordered fcc is discussed through thermodynamical calculations. The condition for the direct transformation from bcc to fcc is also examined. (orig.)

FCC catalyst technologies expand limits of process capability

International Nuclear Information System (INIS)

Leiby, S.

1992-01-01

This paper reports that over the past 30 or so years, many improvements in fluid catalytic cracking (FCC) operation have been achieved as the result of innovations in catalyst formulation. During the 1990s, new environmental regulations on issues such as reformulated gasoline will place new demands on both the refining industry and catalyst suppliers. An overview of cracking catalyst technology therefore seems in order. Today, high-technology innovations by catalyst manufacturers are rapid, but profit margins are slim. Catalyst formulations are shrouded in secrecy and probably depend almost as much on art as on science. Special formulations for specific cracking applications get the greatest emphasis today. To illustrate this point, OGJ's Worldwide Catalyst Report lists over 200 FCC catalyst designations. Catalysts containing components to enhance gasoline octane now account for about 70% of total U.S. FCC catalyst usage

Cross-talk studies between FCC-hh Experimental Interaction Regions

CERN Document Server

AUTHOR|(CDS)2081283; Seryi, Andrei; Appleby, Robert Barrie; Rafique, Haroon; Besana, Maria Ilaria

2017-01-01

Debris from 50 TeV proton-proton collisions at the main interaction point in the FCC-hh may contribute to the background in the subsequent detector. This cross-talk is of possible concern for the FCC-hh due to the high luminosity and energy of the collider. DPMJET-III is used as a collision debris generator in order to assess the muon cross-talk contribution. An analytical calculation of muon range in rock is performed. This is followed by a full Monte Carlo simulation using FLUKA, where the accelerator tunnel has been modelled. The muon cross talk between the adjacent interaction points is assessed and its implications for FCC-hh design are discussed.

FCC Official Brochure - 2016

CERN Multimedia

Charitos, Panagiotis

2016-01-01

The FCC brochure describes the main scope of the study and give more information about the main scenarios explored under the study. It also highlights the R&D efforts under the study that will go into a Conceptual Design Report. Finally, it offers more information about the collaboration and a list of useful contact details.

Report on coal refining and chemical equipment analogous to coal liquefaction equipment in fiscal 1981. Maintenance of equipment for direct desulfurization, indirect desulfurization, and fluidized catalytic cracking; 1981 nendo sekitan ekika ruiji seiyu seisei oyobi kagaku sochi ni kansuru chosa hokokusho. Chokudatsu, kandatsu, ryudo sesshoku bunkai sochi no hozen

Energy Technology Data Exchange (ETDEWEB)

NONE

1981-07-01

This questionnaire survey was intended to investigate the actual state of maintenance such as materials used, conditions for use, anti-corrosion measures, and cases and handling of damage, concerning primary apparatus in the direct/indirect desulfurization equipment and the fluidized catalytic crackers, which are owned by each oil refinery and which are analogous to coal liquefaction equipment. The questionnaire was intended for the following equipment and apparatus, with the actual state of their maintenance investigated. 1. Questionnaire concerning maintenance of direct desulfurization (reactor, high temperature separation tank, material furnace tube, reactor exit piping, high temperature heat exchanger, low temperature heat exchanger, and pressure reducing valve), 2. Questionnaire concerning maintenance of indirect desulfurization (reactor, high temperature separation tank, material furnace tube, reactor exit piping, high temperature heat exchanger, low temperature heat exchanger, and pressure reducing valve), 3. Questionnaire concerning maintenance of fluidized catalytic cracker (reactor, regeneration tower, riser pipe, and fractionator bottom pump). The questionnaire this time was distributed to 27 domestic oil companies, with the reply received from 23 of them. The replies were summarized by each type of equipment. Shown at the back of the report were the cases of damage and handling in FCC's and reactors. (NEDO)

FCC-ee accelerator parameters, performance and limitations

CERN Document Server

Koratzinos, Mike

2016-12-22

CERN has recently launched the Future Circular Collider (FCC) study to deal with all aspects of an ambitious post-LHC possible programme. The emphasis of the study is on a 100 TeV proton collider to be housed in a 80-100 km new ring in the Geneva region. An electron machine will also be considered as a possible intermediate first step (FCC-ee). The study benefits from earlier work done in the context of TLEP and has already published a parameter table, to serve as the basis for the work to be done. The study aims to publish a conceptual design report at around 2018. The recent discovery of a light Higgs boson has opened up considerable interest in circular e+e- Higgs factories around the world. FCC-ee is capable of very high luminosities in a wide centre-of-mass (ECM) spectrum from 90 to 350 GeV. This allows the very precise study of the Z, W and H bosons as well as the top quark, allowing for meaningful precision tests of the closure of the Standard Model.

Beam Optics for FCC-ee Collider Ring

CERN Document Server

Oide, Katsunobu; Aumon, S; Benedikt, M; Blondel, A; Bogomyagkov, A V; Boscolo, M; Burkhardt, H; Cai, Y; Doblhammer, A; Haerer, B; Holzer, B; Koop, I; Koratzinos, M; Jowett, John M; Levichev, E B; Medina, L; Ohmi, K; Papaphilippou, Y; Piminov, P A; Shatilov, D N; Sinyatkin, S V; Sullivan, M; Wenninger, J; Wienands, U; Zhou, D; Zimmermann, F

2017-01-01

A beam optics scheme has been designed [ 1 ] for the Future Circular Collider- e + e − (FCC-ee). The main characteristics of the design are: beam energy 45 to 175 GeV, 100 km circumference with two interaction points (IPs) per ring, horizontal crossing angle of 30 mrad at the IP and the crab-waist scheme [ 2 ] with local chromaticity correction. The crab-waist scheme is implemented within the local chromaticity correction system without additional sextupoles, by reducing the strength of one of the two sextupoles for vertical chromatic correction at each side of the IP. So- called “tapering" of the magnets is applied, which scales all fields of the magnets according to the local beam energy to compensate for the effect of synchrotron radiation (SR) loss along the ring. An asymmetric layout near the interaction region reduces the critical energy of SR photons on the incoming side of the IP to values below 100 keV, while matching the geometry to the beam line of the FCC proton collider (FCC-hh) [ 3 ] as clos...

Tools for Inspecting and Sampling Waste in Underground Radioactive Storage Tanks with Small Access Riser Openings

International Nuclear Information System (INIS)

Nance, T.A.

1998-01-01

Underground storage tanks with 2 inches to 3 inches diameter access ports at the Department of Energy's Savannah River Site have been used to store radioactive solvents and sludge. In order to close these tanks, the contents of the tanks need to first be quantified in terms of volume and chemical and radioactive characteristics. To provide information on the volume of waste contained within the tanks, a small remote inspection system was needed. This inspection system was designed to provide lighting and provide pan and tilt capabilities in an inexpensive package with zoom abilities and color video. This system also needed to be utilized inside of a plastic tent built over the access port to contain any contamination exiting from the port. This system had to be build to travel into the small port opening, through the riser pipe, into the tank evacuated space, and out of the riser pipe and access port with no possibility of being caught and blocking the access riser. Long thin plates were found in many access riser pipes that blocked the inspection system from penetrating into the tank interiors. Retrieval tools to clear the plates from the tanks using developed sampling devices while providing safe containment for the samples. This paper will discuss the inspection systems, tools for clearing access pipes, and solvent sampling tools developed to evaluate the tank contents of the underground solvent storage tanks

Single-crystal FCC and DHCP phases in Ce/Pr superlattices

International Nuclear Information System (INIS)

Lee, S.; Goff, J.P.; Ward, R.C.C.; Wells, M.R.; McIntyre, G.J.

2002-01-01

Cerium usually comprises a mixture of polycrystalline FCC and DHCP allotropes. Single-crystal Ce has been stabilised in Ce/Pr superlattices grown using molecular beam epitaxy. It is found that FCC or DHCP phases can be obtained depending on superlattice composition and growth conditions. Low-temperature neutron scattering was performed on Ce/Pr samples using the triple-axis spectrometer D10 at the ILL. Such measurements revealed one sample, [Ce 20 Pr 20 ] 60 , to be a single crystal with a DHCP unit cell; while another, [Ce 30 Pr 10 ] 56 , was a mixture of FCC and DHCP phases. Antiferromagnetic ordering of magnetic moments was observed in the DHCP sample (T N =11.1 K) with a magnetic structure similar to that found in bulk β-Ce. Surprisingly, the magnetic ordering was found to be confined to single Ce blocks. Furthermore, it was found that, at low temperatures, the lattice contraction observed for bulk FCC Ce was suppressed in Ce/Pr superlattices. (orig.)

A procedure to identify and to assess risk parameters in a SCR (Steel Catenary Riser) due to the fatigue failure

Energy Technology Data Exchange (ETDEWEB)

Stefane, Wania [Universidade Estadual de Campinas (UNICAMP), Campinas, SP (Brazil). Faculdade de Engenharia Mecanica; Morooka, Celso K. [Universidade Estadual de Campinas (UNICAMP), Campinas, SP (Brazil). Dept. de Engenharia de Petroleo. Centro de Estudos de Petroleo; Pezzi Filho, Mario [PETROBRAS S.A., Rio de Janeiro, RJ (Brazil). E and P. ENGP/IPMI/ES; Matt, Cyntia G.C.; Franciss, Ricardo [PETROBRAS S.A., Rio de Janeiro, RJ (Brazil). Centro de Pesquisas (CENPES)

2009-12-19

The discovery of offshore fields in ultra deep water and the presence of reservoirs located in great depths below the seabed requires innovative solutions for offshore oil production systems. Many riser configurations have emerged as economically viable technological solutions for these scenarios. Therefore the study and the development of methodologies applied to riser design and procedures to calculate and to dimension production risers, taken into account the effects of mete ocean conditions, such as waves, current and platform motion in the fatigue failure is fundamental. The random nature of these conditions as well as the mechanical characteristics of the riser components are critical to a probabilistic treatment to ensure the greatest reliability for risers and minimum risks associated to different aspects of the operation like the safety of the installation, economical concerns and the environment. The current work presents a procedure of the identification and the assessment of main parameters of risk when considering fatigue failure. Static and dynamic behavior of Steel Catenary Riser (SCR) under the effects of mete ocean conditions and uncertainties related to total cumulative damage (Miner-Palmgren's rule) are taken into account. The methodology adopted is probabilistic and the approach is analytical. The procedure is based on the First Order Reliability Method (FORM) which usually presents low computational effort and acceptable accuracy. The procedure suggested is applied for two practical cases, one using data available from the literature and the second with data collected from an actual Brazilian offshore field operation. For both cases, results of the probability of failure due to fatigue were obtained for different locations along the SCR length connected to a semi-submersible platform. From these results, the sensitivity of the probability of failure due to fatigue for a SCR could be verified, and the most effective parameter could also be

Future Circular Collider Study FCC-he Baseline Parameters

CERN Document Server

Bruning, Oliver; Klein, Max; Pellegrini, Dario; Schulte, Daniel; Zimmermann, Frank

2017-01-01

Initial considerations are presented on the FCC-he, the electron-hadron collider con guration within the Future Circular Collider study. This note considers arguments for the choice of the electron beam energy based on physics, ep scattering kinematics and cost. The default con guration for the electron accelerator, as for the LHeC, is chosen to be a multi-turn energy recovery linac external to the proton beam tunnel. The main accelerator parameters of the FCC-he are discussed, assuming the concurrent operation of ep with the 100TeV cms energy pp collider. These are compared with the LHeC design concept, for increased performance as for a Higgs facility using the HL-LHC, and also the high energy HE-LHC ep collider configuration. Initial estimates are also provided for the luminosity performance of electron-ion colliders for the 60 GeV electron ERL when combined with the LHC, the HE-LHC and the FCC ion beams.

Phonon dispersion curves of fcc La

International Nuclear Information System (INIS)

Stassis, C.; Loong, C.; Zarestky, J.

1982-01-01

Large single crystals of fcc La were grown in situ and were used to study the lattice dynamics of this phase of La by coherent inelastic neutron scattering. The phonon dispersion curves have been measured along the [xi00], [xixi0], [xixixi], and [0xi1] symmetry directions at 660 and 1100 K. The T[xixixi] branch exhibits anomalous dispersion for xi>0.25 and, in addition, close to the zone boundary, the phonon frequencies of this branch decrease with decreasing temperature. This soft-mode behavior may be related to the #betta→α# transformation in La, an assumption supported by recent band-theoretical calculations of the generalized susceptibility of fcc La. At X the frequencies of the L[xi00] branch are considerably lower than those of the corresponding branch of #betta#-Ce; a similar but not as pronounced effect is observed for the frequencies of the L[xixixi] branch close to the point L. Since the calculated generalized susceptibility of fcc La exhibits strong peaks at X and L, these anomalies may be due to the renormalization of the phonon frequencies by virtual fbold-arrow-left-rightd transitions to the unoccupied 4f level in La. The data were used to evaluate the elastic constants, the phonon density of states, and the lattice specific heat at constant pressure C/sub P//sup

47 CFR 2.926 - FCC identifier.

Science.gov (United States)

2010-10-01

... representative may receive a grantee code electronically via the Internet at https://gullfoss2.fcc.gov/prod/oet... which has not been granted equipment authorization where such grant is required prior to marketing...

Nucleation of fcc Ta when heating thin films

International Nuclear Information System (INIS)

Janish, Matthew T.; Mook, William M.; Carter, C. Barry

2015-01-01

Thin tantalum films have been studied during in situ heating in a transmission electron microscope. Diffraction patterns from the as-deposited films were typical of amorphous materials. Crystalline grains were observed to form when the specimen was annealed in situ at 450 °C. Particular attention was addressed to the formation and growth of grains with the face-centered cubic (fcc) crystal structure. These observations are discussed in relation to prior work on the formation of fcc Ta by deformation and during thin film deposition

An analytic solution of the static problem of inclined risers conveying fluid

KAUST Repository

Alfosail, Feras

2016-05-28

We use the method of matched asymptotic expansion to develop an analytic solution to the static problem of clamped–clamped inclined risers conveying fluid. The inclined riser is modeled as an Euler–Bernoulli beam taking into account its self-weight, mid-plane stretching, an applied axial tension, and the internal fluid velocity. The solution consists of three parts: an outer solution valid away from the two boundaries and two inner solutions valid near the two ends. The three solutions are then matched and combined into a so-called composite expansion. A Newton–Raphson method is used to determine the value of the mid-plane stretching corresponding to each applied tension and internal velocity. The analytic solution is in good agreement with those obtained with other solution methods for large values of applied tensions. Therefore, it can be used to replace other mathematical solution methods that suffer numerical limitations and high computational cost. © 2016 Springer Science+Business Media Dordrecht

Site occupation state of deuterium atoms in fcc Fe

International Nuclear Information System (INIS)

Aoki, Katsutoshi; Machida, Akihiko; Saitoh, Hiroyuki; Hattori, Takanori; Sano-Furukawa, Asami

2015-01-01

The deuterization process of fcc Fe to form solid-solution fcc FeD x was investigated by in situ neutron diffraction measurements at high temperature and high pressure. In a completely deuterized specimen at 988 K and 6.3 GPa, deuterium atoms occupy the octahedral and tetrahedral interstitial sites with an occupancy of 0.532(9) and 0.056(5), respectively, giving a deuterium composition x of 0.64(1). During deuterization, the metal-lattice expands approximately linearly with deuterium composition at a rate of 2.21 Å 3 per deuterium atom. The minor occupation of tetrahedral site is likely driven by the intersite movement of deuterium atoms along the <111> direction in the fcc metal lattice. These results provide implications for the light elements in the Earth's core and the mechanism of hydrogen embrittlement of ferrous metals. (author)

Clashing of risers due to vortex induced vibrations

Energy Technology Data Exchange (ETDEWEB)

Teissier, D. [Ecole Superieure d' Ingenieurs de Marseille (ESIM), 13 - Marseille (France)]|[Institut Francais du Petrole (IFP), 92 - Rueil-Malmaison (France); Scolan, Y.M. [Ecole Superieure d' Ingenieurs de Marseille (ESIM), 13 - Marseille (France); Fontaine, E. [Institut Francais du Petrole (IFP), 92 - Rueil-Malmaison (France)

2004-07-01

Phenomena such as Vortex Induced Vibrations can potentially damage offshore risers, especially in ar ay configurations. Due to wake interferences, amplification of VIV is observed leading to large displacements which are no more self limited to one di meter as in the case of VIV. In this context, clash ng becomes also an issue. In order to study this problems, Institut Francais du Petrole is developing a Computational Fluid Dynamics code, DeepFlow, devoted to the simulation of two-dimensional flows around risers. The extension to three-dimensional configurations follows from a strip theory for the fluid flow, coupled to a structural model for flexible pipes (DeepLines). The numerical method (Etienne s 1999) developed in DeepFlow allows to solve the two-dimensional Reynolds Averaged Navier-Stokes equations through a mixed representation (Eulerian and Lagrangian) of the flow properties: vorticity and turbulence. The Eulerian method is necessary in the close vicinity of the bodies in order to capture the boundary layer effects with accuracy, whereas the Lagrangian representation, based on a grid-less method is suitable for the flow in the wake. In the present pa-per, this approach is applied to study the flow around two freely moving cylinders. For this test case, there are some numerical results (Sagatum et al, 2002), however instabilities have been experimentally identified (Paidoussis et al, 1998; Zdravkovich, 1985, 2003). The approach has also been improved to solve accurately the interstitial flow when the bodies are very close to each other. Results from a Chimera approach are presented. (authors)

Analysis on flow characteristic of nuclear heating reactor

International Nuclear Information System (INIS)

Jiang Shengyao; Wu Xinxin

1997-06-01

The experiment was carried out on the test loop HRTL-5, which simulates the geometry and system design of a 5 MW Nuclear heating reactor. The analysis was based on a one-dimensional two-phase flow drift model with conservation equations for mass, steam mass, energy and momentum. Clausius-Clapeyron equation was used for the calculation of flashing front in the riser. A set of ordinary equation, which describes the behavior of two-phase flow in the natural circulation system, was derived through integration of the above conservation equations in subcooled boiling region, bulk boiling region in the heated section and in the riser. The method of time-domain was used for the calculation. Both static and dynamic results are presented. System pressure, inlet subcooling and heat flux are varied as input parameters. The results show that, firstly, subcooled boiling in the heated section and void flashing in the riser have significant influence on the distribution of the void fraction, mass flow rate and stability of the system, especially at lower pressure, secondly, in a wide range of two-phase flow conditions, only subcooled boiling occurs in the heated section. For the designed two-phase regime operation of the 5 MW nuclear heating reactor, the temperature at the core exit has not reaches its saturation value. Thirdly, the mechanism of two-phase flow oscillation, namely, 'zero-pressure-drop', is described. In the wide range of inlet subcooling (0 K<ΔT<28 K) there exists three regions for system flow condition, namely, (1) stable two-phase flow, (2) bulk and subcooled boiling unstable flow, (3) subcooled boiling and single phase stable flow. The response of mass flow rate, after a small disturbance in the heat flux, is showed in the above inlet subcooling range, and based on it the instability map of the system is given through experiment and calculation. (3 refs., 9 figs.)

Catalytic Transformation of Ethylbenzene over Y-Zeolite-based Catalysts

KAUST Repository

Al-Khattaf, Sulaiman

2008-11-19

Catalytic transformation of ethylbenzene (EB) has been investigated over ultrastable Y (USY)-zeolite-based catalysts in a novel riser simulator at different operating conditions. The effect of reaction conditions on EB conversion is reported. The USY catalyst (FCC-Y) was modified by steaming to form a significantly lower acidity catalyst (FCC-SY). The current study shows that the FCC-SY catalyst favors EB disproportionation more than cracking. A comparison has been made between the results of EB conversion over the lowly acidic catalyst (FCC-SY) and the highly acidic catalyst (FCC-Y) under identical conditions. It was observed that increase in catalyst acidity favored cracking of EB at the expense of disproportionation. Kinetic parameters for EB disappearance during disproportionation reaction over the FCC-SY catalyst were calculated using the catalyst activity decay function based on time on stream (TOS). © 2008 American Chemical Society.

Structural and magnetic properties of hcp and fcc Ni nanoparticles

International Nuclear Information System (INIS)

Gong, J.; Wang, L.L.; Liu, Y.; Yang, J.H.; Zong, Z.G.

2008-01-01

The face-centered-cubic (fcc) and hexagonal-close-packed (hcp) Ni nanoparticles were synthesized with citrate by sol-gel method and heat-treating technique. The structure, morphology and magnetic properties of the samples were characterized using X-ray diffraction (XRD), transmission electron microscopy (TEM), and vibrating sample magnetometer (VSM). Our XRD and TEM results suggested that hcp Ni nanoparticles were successfully synthesized when the heating temperature reaches 300 deg. C. With a further increase in temperature to 400 deg. C, a temperature-induced phase transformation of hcp to fcc was observed. Moreover, the VSM results demonstrated the existence of ferromagnetic behavior in the synthesized fcc and hcp Ni nanoparticles. Nevertheless, the magnetic measurement suggested that the magnetic properties in hcp nanoparticles is probably the sum of two contributions: superparamagnetic and ferromagnetic one. The unsaturated magnetization is much smaller than 47.6 emu/g for the fcc nanoparticles obtained at 400 deg. C and 55 emu/g for the bulk material. It was also found that changes of the stress, grain size and crystal structure during heat-treating have significant influences on the magnetic properties of the Ni nanoparticles

Direct measurement of alpha_QED(mZ)at the FCC-ee

CERN Document Server

Janot, Patrick

2016-02-08

When the measurements from the FCC-ee become available, an improved determination of the standard-model "input" parameters will be needed to fully exploit the new precision data towards either constraining or fitting the parameters of beyond-the-standard-model theories. Among these input parameters is the electromagnetic coupling constant estimated at the Z mass scale, alpha_QED(mZ). The measurement of the muon forward- backward asymmetry at the FCC-ee, just below and just above the Z pole, can be used to make a direct determination of alpha_QED(mZ) with an accuracy deemed adequate for an optimal use of the FCC-ee precision data.

Measuring light-by-light scattering at the LHC and FCC

CERN Document Server

d'Enterria, David

2016-01-01

Elastic light-by-light scattering, $\\gamma\\gamma\\to\\gamma\\gamma$, can be measured in electromagnetic interactions of lead (Pb) ions at the Large Hadron Collider (LHC) and Future Circular Collider (FCC), using the large (quasi)real photon fluxes available in ultraperipheral collisions. The $\\gamma\\gamma\\to\\gamma\\gamma$ cross sections for diphoton masses m$_{\\gamma\\gamma}>$ 5 GeV in pp, pPb, and PbPb collisions at LHC ($\\sqrt{\\rm s_{_{NN}}}$ = 5.5, 8.8, 14 TeV) and FCC ($\\sqrt{\\rm s_{_{NN}}}$ = 39, 63, 100 TeV) center-of-mass energies are presented. The measurement has controllable backgrounds in PbPb collisions, and one expects about 70 and 2500 signal events per year at the LHC and FCC respectively, after typical detector acceptance and reconstruction efficiency selections.

Vacancy formation enthalpies in bcc and fcc FeCo by positron annihilation

International Nuclear Information System (INIS)

Jackman, J.A.; Kim, S.M.; Buyers, W.J.L.

1982-01-01

A long slit angular correlation apparatus was used to measure the peak coincidence count rate in stoichiometric FeCo from 290 K to 1510 K. The count rate did not change significantly at the order-disorder phase transition (1008 K), but decreased sharply by 3.2% at the bcc-fcc phase transition at 1258 K. The threshold temperatures for the trapping of positrons in vacancies are measured to be 1125 K for the bcc phase and 1260 K for the fcc phase. The vacancy formation enthalpies in the bcc and fcc phases are determined to be 1.45 +- 0.05 eV and 1.63 +- 0.05 eV. The activation energies for self-diffusion have been estimated from the threshold temperatures, and are found to be 2.45 eV and 2.74 eV for the bcc and fcc phases respectively. (Auth.)

Bulk Nanostructured FCC Steels With Enhanced Radiation Tolerance

Energy Technology Data Exchange (ETDEWEB)

Zhang, Xinghang; Hartwig, K. Ted; Allen, Todd; Yang, Yong

2012-10-27

The objective of this project is to increase radiation tolerance in austenitic steels through optimization of grain size and grain boundary (GB) characteristics. The focus will be on nanocrystalline austenitic Fe-Cr-Ni alloys with an fcc crystal structure. The long-term goal is to design and develop bulk nanostructured austenitic steels with enhanced void swelling resistance and substantial ductility, and to enhance their creep resistance at elevated temperatures via GB engineering. The combination of grain refinement and grain boundary engineering approaches allows us to tailor the material strength, ductility, and resistance to swelling by 1) changing the sink strength for point defects, 2) by increasing the nucleation barriers for bubble formation at GBs, and 3) by changing the precipitate distributions at boundaries. Compared to ferritic/martensitic steels, austenitic stainless steels (SS) possess good creep and fatigue resistance at elevated temperatures, and better toughness at low temperature. However, a major disadvantage of austenitic SS is that they are vulnerable to significant void swelling in nuclear reactors, especially at the temperatures and doses anticipated in the Advanced Burner Reactor. The lack of resistance to void swelling in austenitic alloys led to the switch to ferritic/martensitic steels as the preferred material for the fast reactor cladding application. Recently a type of austenitic stainless steel, HT-UPS, was developed at ORNL, and is expected to show enhanced void swelling resistance through the trapping of point defects at nanometersized carbides. Reducing the grain size and increasing the fraction of low energy grain boundaries should reduce the available radiation-produced point defects (due to the increased sink area of the grain boundaries), should make bubble nucleation at the boundaries less likely (by reducing the fraction of high-energy boundaries), and improve the strength and ductility under radiation by producing a higher

The use of titanium alloys for dynamic risers: a literature review

Energy Technology Data Exchange (ETDEWEB)

Torster, F.; Kocak, M.; Santos, J.F. dos [GKSS-Forschungszentrum Geesthacht GmbH (Germany). Inst. fuer Werkstofforschung; Hutt, G. [Stolt Comex Seaway Ltd., Aberdeen, (Scotland)

1997-12-31

The main topic of this short literature review is to describe the material related aspects concerning the production and purpose of flexible titanium risers for offshore oil and gas production. Metallurgy and alloying of titanium are briefly introduced. The review concentrates on the materials properties that are relevant for the intended use in marine environment. The focus is put on {alpha}+{beta} Ti-alloys, because earlier investigations have shown that this alloy family is the most suitable one for this purpose. Further topics which are taken into account are welding processes for titanium, weld properties and aspects of the associated weld defects as well. This literature review has been carried out at GKSS-Forschungszentrum Geesthacht GmbH within the framework of the project `Titanium Risers for Deepwater Developments (contract nr. OG/175/95), supported by the THERMIE-JOULE Programme of the European Commission. The project consortium is formed by Stolt Comex Seaway Ltd. (UK), Seaflex AS (Norway) and GKSS (Germany). (orig.) [Deutsch] Die vorliegende kurze Literaturrecherche befasst sich vorrangig mit den materialbezogenen Aspekten der Produktion und des Einsatzes von flexiblen `Risern` aus Titanlegierungen fuer die Oel- und Gasfoerderung auf See. Die Metallurgie und das Legieren von Titan werden kurz vorgestellt. Die Recherche konzentriert sich im weiteren auf die Materialeigenschaften, die fuer den vorgesehenen Einsatz in mariner Umgebung von besonderer Bedeutung sind. In erster Linie wird dabei auf {alpha}+{beta}-Titanlegierungen eingegangen, da vorausgegangene Untersuchungen gezeigt haben, dass diese Legierungsfamilie die guenstigsten Eigenschaften fuer das vorgesehene Einsatzgebiet aufweist. Im weiteren werden die Schweissprozesse, die bei Titanlegierungen eingesetzt werden, vorgestellt und die Eigenschaften und moeglichen Schweissfehler der hergestellten Schweissverbindungen gegenuebergestellt. Diese Literaturrecherche wurde im GKSS-Forschungszentrum im

Necessary Tension in Marine Risers Tension des colonnes montantes en mer

Directory of Open Access Journals (Sweden)

Lubinski A.

2006-11-01

Full Text Available The tension governing transverse static and dynamic deflections in a riser is not the actual tension but the so-called « effective tension » The concept of effective tension and effective compression is thoroughly explained, and means for calculating effective forces are given. Numerical examples are worked out for risers whose length is between 152 m (520 ft and 920 m (3020 ft. The reciprocal of maximum bending moment of the vicinity of the hall joint is plotted versus the effective tension of the ball joint. Bending moments used were obtained through use of static and dynamic computer programs applied ta a variety of conditions of wave loading, use or non-use of buoyant moterial sleeves, etc. The most important parameters affecting riser performance are the effective La tension régissant les déflections transversales statiques et dynamiques d'une colonne montante n'est pas la tension réelle mais ce qu'on appelle « la tension effective ». Le concept de tension ou de compression effective est expliqué en détail et la façon de calculer les forces effectives est indiquée dans cet article. Des exemples numériques sont développés pour des colonnes montantes de longueur comprise entre 152 m (520 ft et 920 m (3 020 ft. On a tracé la courbe de l'inverse du moment fléchissant en fonction de la tension effective à l'articulation. Les moments fléchissants utilisés ont été calculés par ordinateur en utilisant des programmes dynamiques et statiques pour des conditions variées d'action des vagues, la colonne montante étant ou non munie de manchettes de flottabilité, etc. Les deux paramètres les plus importants qui affectent le bon comportement d'une colonne montante sont la tension effective et la charge latérale.

Status of the FCC-ee Interaction Region Design

CERN Document Server

Roman Martin; Medina, L

2015-01-01

The FCC-ee project is a high-luminosity circular electron-positron collider envisioned to operate at center-of-mass energies from 90 to 350 GeV, allowing high-precision measurements of the properties of the Z, W and Higgs boson as well as the top quark. It is considered to be a predecessor of a new 100 TeV proton-proton collider hosted in the same 80 to 100 km tunnel in the Geneva area. Currently two interaction region designs are being developed by CERN and BINP using different approaches to the definition of baseline parameters. Both preliminary designs are presentedwith the aimof highlighting the challenges the FCC-ee is facing.

Interdiffusion and atomic mobility studies in Ni-rich fcc Ni−Al−Mn alloys

International Nuclear Information System (INIS)

Cheng, Kaiming; Liu, Dandan; Zhang, Lijun; Du, Yong; Liu, Shuhong; Tang, Chengying

2013-01-01

Highlights: •The interdiffusion coefficients of fcc Ni–Al–Mn alloys are experimentally determined. •The atomic mobilities of fcc Ni–Al–Mn alloys have been assessed. •The calculated results agree well with the present experimental diffusivities. •The mobility parameters obtained can be used to predict many diffusion phenomena. -- Abstract: By employing nine groups of bulk diffusion couples together with electron probe microanalysis technique, the composition dependence of ternary interdiffusion coefficients in Ni-rich fcc Ni−Al−Mn alloys at 1373 K was determined via the Matano–Kirkaldy method. The experimental interdiffusion coefficients were critically assessed to obtain the atomic mobilities of Ni, Al and Mn in fcc Ni−Al−Mn alloys by using the DICTRA (DIffusion-Controlled TRAnsformations) software package. The reliability of these mobilities was validated by comprehensive comparison between the model-predicted diffusion properties and the experimental data. The obtained atomic mobilities could be used to describe various diffusion phenomena in fcc Ni–Al–Mn alloys, such as the concentration profiles, interdiffusion flux and diffusion paths

Anchoring FRP Composite Armor in Flexible Offshore Riser Systems

DEFF Research Database (Denmark)

Costache, Andrei

things, they serve for the transportation of hydrocarbons from the subsea facilities to the production and drilling equipment at the sea surface. Flexible risers are the prime choice for connecting floating production, storage and offloading facilities, because they are specially designed for dynamic...... counterpart. A new double grip design with flat faces is proposed, in which the loads are transferred through friction. The behavior of such grip is studied by means of experimental testing and finite element modeling. Several iterations of the grip system were evaluated over the course of the project...

Ground state searches in fcc intermetallics

International Nuclear Information System (INIS)

Wolverton, C.; de Fontaine, D.; Ceder, G.; Dreysse, H.

1991-12-01

A cluster expansion is used to predict the fcc ground states, i.e., the stable phases at zero Kelvin as a function of composition, for alloy systems. The intermetallic structures are not assumed, but derived regorously by minimizing the configurational energy subject to linear constraints. This ground state search includes pair and multiplet interactions which spatially extend to fourth nearest neighbor. A large number of these concentration-independent interactions are computed by the method of direct configurational averaging using a linearized-muffin-tin orbital Hamiltonian cast into tight binding form (TB-LMTO). The interactions, derived without the use of any adjustable or experimentally obtained parameters, are compared to those calculated via the generalized perturbation method extention of the coherent potential approximation within the context of a KKR Hamiltonian (KKR-CPA-GPM). Agreement with the KKR-CPA-GPM results is quite excellent, as is the comparison of the ground state results with the fcc-based portions of the experimentally-determined phase diagrams under consideration

Development of Millimeter-Wave Velocimetry and Acoustic Time-of-Flight Tomography for Measurements in Densely Loaded Gas-Solid Riser Flow

Energy Technology Data Exchange (ETDEWEB)

Fort, James A.; Pfund, David M.; Sheen, David M.; Pappas, Richard A.; Morgen, Gerald P.

2007-04-01

The MFDRC was formed in 1998 to advance the state-of-the-art in simulating multiphase turbulent flows by developing advanced computational models for gas-solid flows that are experimentally validated over a wide range of industrially relevant conditions. The goal was to transfer the resulting validated models to interested US commercial CFD software vendors, who would then propagate the models as part of new code versions to their customers in the US chemical industry. Since the lack of detailed data sets at industrially relevant conditions is the major roadblock to developing and validating multiphase turbulence models, a significant component of the work involved flow measurements on an industrial-scale riser contributed by Westinghouse, which was subsequently installed at SNL. Model comparisons were performed against these datasets by LANL. A parallel Office of Industrial Technology (OIT) project within the consortium made similar comparisons between riser measurements and models at NETL. Measured flow quantities of interest included volume fraction, velocity, and velocity-fluctuation profiles for both gas and solid phases at various locations in the riser. Some additional techniques were required for these measurements beyond what was currently available. PNNL’s role on the project was to work with the SNL experimental team to develop and test two new measurement techniques, acoustic tomography and millimeter-wave velocimetry. Acoustic tomography is a promising technique for gas-solid flow measurements in risers and PNNL has substantial related experience in this area. PNNL is also active in developing millimeter wave imaging techniques, and this technology presents an additional approach to make desired measurements. PNNL supported the advanced diagnostics development part of this project by evaluating these techniques and then by adapting and developing the selected technology to bulk gas-solids flows and by implementing them for testing in the SNL riser

Pressure Profile in the experimental area of FCC-hh and FCC-ee calculated by an analytical code

CERN Multimedia

Aichinger, Ida

2017-01-01

Ultra high vacuum in the beam pipe is a basic requirement for the Future Circular Colliders (FCC). The dimension of the FCC and the high energy of the particles will make this requirement challenging. Simulations that predict the vacuum quality due to material and beam induced effects will allow to evaluate different designs and to choose an optimal solution. The mathematical model behind the simulations will be shown. Four coupled differential equations describe the mass conservation of the residual gas particles in the beam pipe. The sinks include all kind of distributed and local pumping. The sources are caused by synchrotron radiation, electron clouds, thermal outgassing and ion-induced desorption. The equation system is solved by an analytical method. This requires a transformation to first order equations for which a general valid solution exists. Adding a particular solution and the inclusion of appropriate boundary conditions define the solution function. The big advantage here is that an analytical...

Hydrodynamic study of an internal airlift reactor for microalgae culture.

Science.gov (United States)

Rengel, Ana; Zoughaib, Assaad; Dron, Dominique; Clodic, Denis

2012-01-01

Internal airlift reactors are closed systems considered today for microalgae cultivation. Several works have studied their hydrodynamics but based on important solid concentrations, not with biomass concentrations usually found in microalgae cultures. In this study, an internal airlift reactor has been built and tested in order to clarify the hydrodynamics of this system, based on microalgae typical concentrations. A model is proposed taking into account the variation of air bubble velocity according to volumetric air flow rate injected into the system. A relationship between riser and downcomer gas holdups is established, which varied slightly with solids concentrations. The repartition of solids along the reactor resulted to be homogenous for the range of concentrations and volumetric air flow rate studied here. Liquid velocities increase with volumetric air flow rate, and they vary slightly when solids are added to the system. Finally, liquid circulation time found in each section of the reactor is in concordance with those employed in microalgae culture.

Towards a Monochromatization Scheme for Direct Higgs Production at FCC-ee

CERN Document Server

Valdivia Garcia, Marco Alan; Zimmermann, Frank

2016-01-01

Direct Higgs production in e+e− collisions at the FCC is of interest if the centre-of-mass energy spread can be reduced by at least an order of magnitude. A monochromatization scheme, to accomplish this, can be realized with horizontal dispersion of opposite sign for the two colliding beams at the interaction point (IP). We recall historical approaches to monochromatization, then derive a set of IP parameters which would provide the required performance in FCC e+e− collisions at 62.5 GeV beam energy, compare these with the baseline optics parameters at neighbouring energies (45.6 and 80 GeV), comment on the effect of beamstrahlung, and indicate the modifications of the FCC-ee final-focus optics needed to obtain the required parameters.

Diffusivities and atomic mobilities in disordered fcc and ordered L12 Ni–Al–W alloys

International Nuclear Information System (INIS)

Chen, Chong; Zhang, Lijun; Xin, Jinghua; Wang, Yaru; Du, Yong; Luo, Fenghua; Zhang, Zhongjian; Xu, Tao; Long, Jianzhan

2015-01-01

Highlights: • The atomic mobilities for fcc Al–W, fcc Ni–W, fcc Ni–Al–W and L1 2 Ni–Al–W alloys were critically assessed. • The impurity diffusivity of W in fcc-Al was obtained via first-principles calculations. • The calculated results agree well with the diffusivities available in the literature. • Two fcc/L1 2 -type diffusion couples were prepared and the concentration-distance profiles were measured. • The model-predicted concentration profiles agree well with the experimental data in the literature and in the present work. - Abstract: Based on various experimentally measured diffusivities available in the literature together with the reported thermodynamic parameters, the atomic mobilities for disordered fcc and ordered L1 2 Ni–Al–W alloys were assessed on the basis of a recently developed phenomenological model incorporated in the DICTRA software. In order to provide the missing impurity diffusion coefficients of W in fcc-Al, first-principles calculations were utilized in the present work. Comprehensive comparisons between the calculated and experimental diffusion coefficients show that all the experimental data can be well reproduced by the atomic mobilities obtained in the present work. In order to further verify the reliability of the presently obtained atomic mobilities, two fcc/L1 2 -type diffusion couples (i.e., Ni–5 at.% Al–5 at.% W/Ni–20 at.% Al–4 at.% W and Ni/Ni–22 at.% Al–2 at.% W) were prepared and the concentration-distance profiles after annealing at 1323 K for 86.4 ks were measured. The excellent agreement between the model-predicted concentration-distance profiles and the experimental data indicates that the presently obtained atomic mobilities in fcc/L1 2 Ni–Al–W alloys are reliable

Magnetic properties of metastable bcc and fcc Fe-Cu alloys produced by vapor quenching

International Nuclear Information System (INIS)

Sumiyama, Kenji; Yoshitake, Tsutomu; Nakamura, Yoji

1984-01-01

High concentration Fesub(1-x)Cusub(x) alloys have been obtained by rf sputtering technique and investigated by X-ray diffraction and magnetization measurements. The bcc phase is extended over the region with x=0-0.4, while the fcc phase with x=0.6-1.0. For x=0.4-0.6, we have the mixed phase of bcc and fcc. The lattice constant of bcc phase increases slightly and that of fcc phase decreases with increasing x. In the bcc alloys, the average magnetic moment decreases with increasing x and deviates upwards from the simple dilution law. In the fcc alloys, the magnetic moment also decreases with increasing x but it deviates downwards from the simple dilution law. The Curie temperature, Tsub(c), of the Fesub(1-x)Cusub(x) alloys decreases abruptly with increasing x: Tsub(c) is higher than 750 K for the bcc alloys, while it is lower than 320 K for the fcc alloys and become 0 K at about x=0.92. (author)

Studi Pengaruh Gerak Semi-submersible Drilling Rig dengan Variasi Pre-tension Mooring Line terhadap Keamanan Drilling Riser

Directory of Open Access Journals (Sweden)

Arda Arda

2012-09-01

Full Text Available Analisis terhadap sistem tambat pada anjungan pengeboran semi-submersible drilling rig perlu dilakukan sebelum dilakukannya operasi di lapangan untuk mengetahui perencanaan sistem tambat yang tepat dan aman. Dalam penelitian ini dilakukan analisa perilaku gerak semi-submersible dengan variasi pre-tension mooring line untuk mengetahui berapa besar pre-tension minimal yang harus digunakan agar operasi pengeboran di lingkungan laut Natuna dapat berjalan dengan aman. Variasi pre-tension yang digunakan adalah sebesar 400kN-2000kN dengan penambahan sebesar 400kN. Karakteristik gerakan semi-submersible diprediksi dengan menghitung RAO free floating dengan pemodelan numerik dalam domain frekuensi. Kemudian dilakukan analisa simulasi sistem lengkap (platform, mooring dan drilling riser dengan pemodelan numerik dalam domain waktu. Hasil yang didapat yakni nilai maksimum tegangan mooring line memenuhi batas kriteria API-RP2SK untuk semua variasi pre-tension dengan safety factor terkecil 2.44. Sudut flex joint drilling riser yang terjadi melewati batas kriteria API-RP16Q pada pre-tension 400kN-800kN yang mencapai 6.20 untuk sudut maksimum dan 4.80 untuk sudut rata-rata. Tegangan von Mises yang terjadi pada drilling riser melebihi kriteria API-RP16Q pada pre-tension 400kN-1200kN karena nilainya mencapai 369 MPa (0.82 yield stress.

Magnetic properties of fcc (Co95Fe5)1-xAlx ribbons

International Nuclear Information System (INIS)

Makhlouf, Salah A.; Parker, F.T.; Benameur, T.

1999-01-01

Rapidly quenched (Co 95 Fe 5 ) 1-x Al x ribbons are investigated by X-ray diffraction, magnetization, and Moessbauer effect measurements. A single fcc phase is obtained for all ribbons x ≤ 10 at.%. The lattice constant increases linearly with x and is discussed in connection with magnetic moment. The influence of Al substitution on both magnetization and Fe-atom hyperfine field (H) is studied. At 296 K, the magnetization decreases linearly while H drops nonlinearly as x increases. Al substitution leads to substantial differences in iron hyperfine fields in bcc and fcc systems. Fe moment is perturbed differently by Al substitution in fcc (Co 95 Fe 5 ) 1-x Al x and bcc Fe-Al systems

CIRCUS and DESIRE: Experimental facilities for research on natural-circulation-cooled boiling water reactors

International Nuclear Information System (INIS)

Kruijf, W.J.M. de; Haden, T.H.J.J. van der; Zboray, R.; Manera, A.; Mudde, R.F.

2002-01-01

At the Delft University of Technology two thermohydraulic test facilities are being used to study the characteristics of Boiling Water Reactors (BWRs) with natural circulation core cooling. The focus of the research is on the stability characteristics of the system. DESIRE is a test facility with freon-12 as scaling fluid in which one fuel bundle of a natural-circulation BWR is simulated. The neutronic feedback can be simulated artificially. DESIRE is used to study the stability of the system at nominal and beyond nominal conditions. CIRCUS is a full-height facility with water, consisting of four parallel fuel channels and four parallel bypass channels with a common riser or with parallel riser sections. It is used to study the start-up characteristics of a natural-circulation BWR at low pressures and low power. In this paper a description of both facilities is given and the research items are presented. (author)

Considerations on operation schedule and maintenance aspects of FCC-hh

CERN Document Server

Niemi, Arto; Foraz, Katy

2018-01-01

The Future Circular Hadron Collider (FCC-hh) has ambitious goals for integrated luminosity production. Reaching these goals requires reducing the time for planned technical stops and commissioning, compared to the LHC. This note describes potential options for an FCC-hh operation schedule. Special attention is given to considerations on how to accomplish the required maintenance activities in a limited time frame. The note recommends to study further the feasibility and cost-efficiency of operating without annual stops and longer intervals between long shutdowns.

Reusing a residue of the oil industry (FCC) in the production of building elements

OpenAIRE

Caicedo Casso, Eduard Andrés; Universidad del Valle; Mejía de Gutiérrez, Ruby; Universidad del Valle; Gordillo Suárez, Marisol; Universidad Autónoma de Occidente; Torres Agredo, Janneth; Universidad Nacional de Colombia, sede Palmira

2015-01-01

This paper analyzes the feasibility of using a residue of spent catalyst (FCC) of the cracking process, from a Colombian oil company, in the production of building elements such as locks and pavers. To define the optimal mix of portland cement/FCC, Portland cement mortars with FCC ratios between 0 and 70% as replacement of cement were prepared and its compressive strength is evaluated at ages up to 28 days of curing. Using a statistical processing, applying the methodology of response, the pr...

Interdiffusion coefficients and atomic mobilities in fcc Cu-Fe-Mn alloys

Directory of Open Access Journals (Sweden)

Li J.

2014-01-01

Full Text Available In the present work, the interdiffusion coefficients in fcc Cu-Fe-Mn alloys were experimentally determined via a combination of solid/solid diffusion couples, electron probe microanalysis (EPMA technique and Matano-Kirkaldy method. Based on the reliable thermodynamic description of fcc phase in the Cu-Fe-Mn system available in the literature as well as the ternary diffusion coefficients measured in the present work, the atomic mobilities in fcc Cu-Fe-Mn alloys were assessed by utilizing the DICTRA (Diffusion Controlled TRAnsformation software package. The calculated interdiffusion coefficients based on the assessed atomic mobilities agree well with most of the experimental data. The comprehensive comparison between various model-predicted diffusion properties and the measured data, including the concentration penetration profiles, interdiffusion flux profile, and diffusion paths, further verify the reliability of the presently obtained atomic mobilities.

Elastic-constant systematics in f.c.c. metals, including lanthanides-actinides

Energy Technology Data Exchange (ETDEWEB)

Ledbetter, Hassel [Mechanical Engineering Department, University of Colorado, Boulder, Colorado 80309 (United States); Migliori, Albert [Los Alamos National Laboratory (E536), Los Alamos, New Mexico 87545 (United States)

2008-01-15

For f.c.c. metals, using Blackman's diagram of dimensionless elastic-constant ratios, we consider the systematics of physical properties and interatomic bonding. We focus especially on the lanthanides-actinides La, Ce, Yb, Th, U, Pu, those for which we know some monocrystal elastic constants. Their behavior differs from the other f.c.c. metals, and all except La show a negative Cauchy pressure, contrary to most f.c.c. metals, which show a positive Cauchy pressure. Among the lanthanides-actinides, {delta}-Pu stands apart, consistent with its many odd physical properties. Based on elastic-constant correlations, we suggest that {delta}-Pu possesses a strong s-electron interatomic-bonding component together with a covalent component. Elastically, {delta}-Pu shows properties similar to Yb. (copyright 2008 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

Analytic nearest neighbour model for FCC metals

International Nuclear Information System (INIS)

Idiodi, J.O.A.; Garba, E.J.D.; Akinlade, O.

1991-06-01

A recently proposed analytic nearest-neighbour model for fcc metals is criticised and two alternative nearest-neighbour models derived from the separable potential method (SPM) are recommended. Results for copper and aluminium illustrate the utility of the recommended models. (author). 20 refs, 5 tabs

Energy barrier of bcc-fcc phase transition via the Bain path in Yukawa system

Science.gov (United States)

Kiyokawa, Shuji

2018-05-01

In the Yukawa system with the dimensionless screening parameter κ>1.5 , when bcc-fcc transition occurs via Bain path, we show that spontaneous transitions do not occur even if the system temperature reaches the transition point of bcc-fcc because it is necessary to increase once the free energy in the process of transition from bcc to fcc through Bain deformation. Here, we refer the temporary increment of the free energy during Bain deformation as Bain barrier. Since there are the Bain barriers at the transitions between bcc and fcc phases, these phases may coexist as metastable state in the wide region (not a coexistence line) of κ and the coupling constant Γ. We study the excess energy of the system and the free energy difference between bcc and fcc phases by the Monte Carlo method, where the simulation box is divided into a large number of elements with small volume and a particle in the box is restricted be placed in one of these elements. By this method, we can tabulate the values of the interparticle potential and can calculate the internal energy fast and precisely.

Cross-twinning model of fcc crystal growth

NARCIS (Netherlands)

van de Waal, B.W.

1995-01-01

The theory developed in 1960 by Wagner, Hamilton and Seidensticker (WHS-theory) to explain observed crystal growth phenomena in Ge is critically reviewed and shown to be capable of explaining preservation of ABC stacking order in two dimensions in fcc crystals of effectively spherical closed shell

Cellular Phone Towers, FCC registered communications towers. Points were generated from FCC data latlong. Originally created as a basis of comparison for Appraiser's cell tower points, bu comparison was inconclusive. Represented all registered FCC sites as of 6/26/2003. No, Published in 2003, 1:1200 (1in=100ft) scale, Sedgwick County Government.

Data.gov (United States)

NSGIC Local Govt | GIS Inventory — Cellular Phone Towers dataset current as of 2003. FCC registered communications towers. Points were generated from FCC data latlong. Originally created as a basis of...

Diffusion behavior and atomic mobilities for fcc Cu–Cr–Ni alloys

International Nuclear Information System (INIS)

Xu, Gaochi; Liu, Yajun; Lei, Fuyue; Sheng, Guang; Kang, Zhitao

2015-01-01

In this work, diffusion couples of fcc Cu–Cr–Ni alloys annealed at 1373 K for 80 h are investigated. The interdiffusion coefficients are retrieved from common compositions of two diffusion couples, which are then combined with thermodynamic descriptions to explore atomic mobilities of Cu, Cr and Ni in fcc Cu–Cr–Ni alloys within the CALPHAD framework. In order to confirm the quality of such kinetic characteristics, a comparison between calculated and experimentally measured concentration profiles of diffusion couples and diffusion paths in Gibbs triangle is made, where the agreement is excellent. The results of this study contribute to the establishment of a general Ni-based mobility database for alloy design. - Highlights: • Atomic mobilities of fcc Cu–Cr–Ni phases were determined. • Experimental interdiffusivities were critically evaluated. • Main and cross interdiffusivities show their peculiarities. • The profiles reveal kinetic importance for alloy microstructures

On the modelling and the analysis of two-phase flow instabilities in pipeline-riser systems; Modelisation et analyse des instabilites d'ecoulements diphasiques dans les conduites petrolieres du type pipeline-riser

Energy Technology Data Exchange (ETDEWEB)

Zakarian, E.

2000-03-10

Recent estimations predict that over half the remaining offshore oil and gas reserves are located in deep water and marginal fields. For such reserves, economic recovery methods are required. Then, multiphase flows are transported within pipelines and separated on treatment platforms built in shallow water or processed in onshore facilities. Unfortunately, hydrodynamic instabilities may occur whenever gas and liquid flow in a pipeline, generating serious operating problems. This dissertation presents a new way to model two-phase flows in pipelines such as pipeline-riser systems. Equations are algebraic and differential. Their smoothness depends on the closure laws of the problem such as slip or friction laws. Smooth forms of these closure laws are presented for the first time in this dissertation. Therefore, a mathematical analysis of our model fits into a classical frame: a linear analysis leads to an analytical expression of the boundary between stable and unstable flows. A nonlinear analysis provides for the first time, the bifurcation curves of gas-liquid flows in pipe-riser systems, locally round their stability boundary. (author)

submitter Prospects of Sterile Neutrino Search with the FCC-ee

CERN Document Server

Bay Nielsen, Sissel

A proposed future circular e + e − collider, the FCC-ee, is suggested to search for sterile neutrinos. The Neutrino Minimal Standard Model, νMSM, is a model of sterile neutrinos, that accommodates explanations for several phenomena of physics beyond the Standard Model. This thesis presents an overview of the theoretical motivation for νMSM, an outline of the experimental conditions at the FCC-ee, and a review of previous accelerator bounds for sterile neutrinos. Two studies of sterile neutrinos with masses at the electroweak scale are introduced, an analysis of long lived sterile neutrinos, and an analysis of short lived sterile neutrinos. Both analyses include background studies and sensitivity estimates for the FCC-ee detector. The study of long lived sterile neutrinos is based on a search for detectable displaced vertices with 1012 Z decays, obtaining a search reach on the mixing angle |θ| 2 as small as 10−11. The study of short lived sterile neutrinos is a Monte Carlo study with a cut-based analysi...

submitter Some Critical Collective Effects for the FCC-ee Collider

CERN Document Server

Belli, Eleonora; Migliorati, Mauro; Persichelli, Serena; Rumolo, Giovanni; Spataro, Bruno; Zobov, Mikhail

2017-01-01

In the framework of the Future Circular Collider (FCC) design studies at CERN [1], the high luminosity electron-positron collider FCC-ee is considered as a possible first step towards FCC-hh, a 100 TeV hadron collider in the same tunnel of about 100 km. Table 1 summarizes the main beam parameters at four different center-of-mass energies from 45.6 GeV (Z pole) to 175 GeV (top pair threshold). One of the major issues for such a kind of machine is represented by collective effects due to electromagnetic fields generated by the interaction of the beam with the vacuum chamber, which could produce instabilities, thus limiting the machine operation and performance. An impedance model is needed to study these instabilities, to predict their effects on the beam dynamics and to find a possible solution for their mitigation. Another critical aspect for the future lepton collider is represented by the electron cloud which will be discussed in the last section of this contribution, together with possible strategies to su...

Multiport riser and flange assemblies acceptance test report

International Nuclear Information System (INIS)

Precechtel, D.R.; Schroeder, B.K.

1994-01-01

This document presents the results of the acceptance test for the multiport riser (MPR) and multiport flange (MPF) assemblies. The accepted MPR and MPF assemblies will be used in support of the hydrogen mitigation project for double-shell waste tank 241-SY-101 and other related projects. The testing described in this document verifies that the mechanical and interface features are operating as designed and that the unit is ready for field service. The objectives of the acceptance testing were as follows: Basic equipment functions and mechanical interfaces were verified; Installation and removal of equipment were demonstrated to the degree possible; Operation of the decon spray system and all valving was confirmed; and the accumulated leak rate of the MPR and MPF assemblies was determined

Exploring the $Z' \\rightarrow t\\overline{t}$ heavy resonance at FCC-hh

CERN Document Server

Smith, Rachel Emma Clarke

2017-01-01

My summer student project explored the feasibility of detecting final states with boosted top quarks at 100 TeV with the baseline FCC-hh detector. I focused specifically on the $Z' \\rightarrow t\\overline{t}$ hadronic process. I determined the exclusion cross-section of $Z' \\rightarrow t\\overline{t}$ and the integrated luminosity required to make a discovery at the baseline FCC detector at 95% confidence level.

Quantitative analysis of thermal diffuse X-ray scattering on single crystals. Communication 2. FCC metals

International Nuclear Information System (INIS)

Najsh, V.E.; Novoselova, T.V.; Sagaradze, I.V.; Kvyatkovskij, B.E.; Fedorov, V.I.; Chernenkov, Yu.P.

1994-01-01

With the use of X-ray diffractometer a study was made into the intensity of diffuse scattering in Ni crystals with FCC lattice. Earlier accomplished quantitative analysis for BCC crystals was extended to FCC lattices. Comparative evaluation was made for cooperative thermal oscillation patterns and corresponding diffuse scattering in crystals of various structures. Measurements on FCC crystals were carried out at room temperature using AgK a lpha-radiation in 96 points of Ni crystal. 8 refs., 4 figs

Photonic bandgap structure of 3-D fcc silica nanospheres

Energy Technology Data Exchange (ETDEWEB)

Woo, Y. K.; Ha, N. Y.; Hwang, Ji Soo; Chang, H. J.; Wu, J. W. [Dept. of Physics, Ewha Womans University, Seoul (Korea, Republic of)

2002-07-01

Photonic crystal is an artificial optical material with a periodic dielectric potential, hence exhibiting a bandgap for a propagating electromagnetic wave. We fabricated crystal possessing 3-D fcc opal structure from silica nanospheres. The crystals are self-assembled on a flat glass by evaporating the solvent in the nanosphere suspension at the room temperature. The suspension consists of silica nanospheres with a diameter of 200 nm. The microscopic arrangement of nanospheres is identified by a scanning electron microscope, the resulting structure being fcc.Transmission spectrum of the fabricated photonic crystal in the visible and near-infrared regions is measured at different incident angles to find the distinct Bragg peaks, analysis of which further confirmed the fcc structure of the photonic crystal. From the optical microscopic image, we find that the opal domain varies from 30 μm to 125 μm in size. In order to relate the observed Bragg peaks with the microscopic arrangement of silica nanospheres, we introduced the scalar wave approximation, where the electric field in the medium is treated as a scalar rather than a vector quantity. It is found that the theoretical prediction of the position of bandgap is in a good agreement with the experimental measurement.

Photonic bandgap structure of 3-D fcc silica nanospheres

International Nuclear Information System (INIS)

Woo, Y. K.; Ha, N. Y.; Hwang, Ji Soo; Chang, H. J.; Wu, J. W.

2002-01-01

Photonic crystal is an artificial optical material with a periodic dielectric potential, hence exhibiting a bandgap for a propagating electromagnetic wave. We fabricated crystal possessing 3-D fcc opal structure from silica nanospheres. The crystals are self-assembled on a flat glass by evaporating the solvent in the nanosphere suspension at the room temperature. The suspension consists of silica nanospheres with a diameter of 200 nm. The microscopic arrangement of nanospheres is identified by a scanning electron microscope, the resulting structure being fcc.Transmission spectrum of the fabricated photonic crystal in the visible and near-infrared regions is measured at different incident angles to find the distinct Bragg peaks, analysis of which further confirmed the fcc structure of the photonic crystal. From the optical microscopic image, we find that the opal domain varies from 30 μm to 125 μm in size. In order to relate the observed Bragg peaks with the microscopic arrangement of silica nanospheres, we introduced the scalar wave approximation, where the electric field in the medium is treated as a scalar rather than a vector quantity. It is found that the theoretical prediction of the position of bandgap is in a good agreement with the experimental measurement.

Study for a stress joint at the top of a SCR (Steel Catenary Risers); Estudo de 'stress joints' para o topo de um SCR (Steel Catenary Risers)

Energy Technology Data Exchange (ETDEWEB)

Siqueira, Elizabeth Frauches Netto; Andrade, Edmundo Queiroz de [PETROBRAS S.A., Rio de Janeiro, RJ (Brazil)

2008-07-01

Steel Catenary Risers, SCRs, need a top connection that bears the force transmitted to the platform. Essentially, two types of connections exist on the market: flex joint and stress joint (SJ). PETROBRAS has a SCR with top connection of flex joint type installed on one of its platforms; however, the company has been studying SJ as an option out of SCR top connection. A stress joint is a monolithic structure and can be inspected during manufacture and service, without so many difficult. They are metal structures composed of a uniform bore inserted in a tapered wall that increases gradually to support the force coming from the riser. The objective of this paper is to present a SJ sensitivity study for a production SCR supposedly hardwired to a unit of production of the semi-submersible type. The data used is based on real SCR data. For this study, global and local analyses were conducted for some models of stress joints, varying some parameters such as material and dimensions, allowing for the verification of some of the critical points of this type of connection. The results obtained will be shown in graphs and tensions maps to illustrate comparatively the critical points of the models analyzed. (author)

An accurate and computationally efficient small-scale nonlinear FEA of flexible risers

OpenAIRE

Rahmati, MT; Bahai, H; Alfano, G

2016-01-01

This paper presents a highly efficient small-scale, detailed finite-element modelling method for flexible risers which can be effectively implemented in a fully-nested (FE2) multiscale analysis based on computational homogenisation. By exploiting cyclic symmetry and applying periodic boundary conditions, only a small fraction of a flexible pipe is used for a detailed nonlinear finite-element analysis at the small scale. In this model, using three-dimensional elements, all layer components are...

Electrical Power Budget for FCC-ee

CERN Document Server

Aull, S.; Bozzini, D.; Brunner, O.; Burnet, J.-P.; Butterworth, A.; Calaga, R.; Jensen, E.; Mertens, V.; Milanese, A.; Nonis, M.; Oide, K.; Schwerg, N.; Tavian, L.; Wenninger, J.; Zimmermann, F.; Rinolfi, L; Blondel, A.; Koratzinos, M.; Gorgi Zadeh, S.

2016-01-01

We present a first rough estimate for the electrical power consumption of the FCC-ee lepton collider. This electrical power is dominated by the RF system, which provides the motivation for the ongoing R&D on highly efficient RF power sources. Other contributions come from the warm arc magnets, the cryogenics systems, cooling, ventilation, general services, the particle-physics detectors, and the injector complex.

Passive cooling system for liquid metal cooled nuclear reactors with backup coolant flow path

International Nuclear Information System (INIS)

Hunsbedt, A.; Boardman, C.E.

1993-01-01

A dual passive cooling system for liquid metal cooled nuclear fission reactors is described, comprising the combination of: a reactor vessel for containing a pool of liquid metal coolant with a core of heat generating fissionable fuel substantially submerged therein, a side wall of the reactor vessel forming an innermost first partition; a containment vessel substantially surrounding the reactor vessel in spaced apart relation having a side wall forming a second partition; a first baffle cylinder substantially encircling the containment vessel in spaced apart relation having an encircling wall forming a third partition; a guard vessel substantially surrounding the containment vessel and first baffle cylinder in spaced apart relation having a side wall forming a forth partition; a sliding seal at the top of the guard vessel edge to isolate the dual cooling system air streams; a second baffle cylinder substantially encircling the guard vessel in spaced part relationship having an encircling wan forming a fifth partition; a concrete silo substantially surrounding the guard vessel and the second baffle cylinder in spaced apart relation providing a sixth partition; a first fluid coolant circulating flow course open to the ambient atmosphere for circulating air coolant comprising at lent one down comer duct having an opening to the atmosphere in an upper area thereof and making fluid communication with the space between the guard vessel and the first baffle cylinder and at least one riser duct having an opening to the atmosphere in the upper area thereof and making fluid communication with the space between the first baffle cylinder and the containment vessel whereby cooling fluid air can flow from the atmosphere down through the down comer duct and space between the forth and third partitions and up through the space between the third and second partition and the riser duct then out into the atmosphere; and a second fluid coolant circulating flow

Thermal-Hydraulic Analysis of an Experimental Reactor Cavity Cooling System with Air. Part I: Experiments; Part II: Separate Effects Tests and Modeling

International Nuclear Information System (INIS)

Corradin, Michael; Dominguez, A.; Tokuhiro, Akira; Hamman, K.

2014-01-01

This experimental study investigates the thermal hydraulic behavior and the heat removal performance for a scaled Reactor Cavity Cooling System (RCCS) with air. A quarter-scale RCCS facility was designed and built based on a full-scale General Atomics (GA) RCCS design concept for the Modular High Temperature Gas Reactor (MHTGR). The GA RCCS is a passive cooling system that draws in air to use as the cooling fluid to remove heat radiated from the reactor pressure vessel to the air-cooled riser tubes and discharged the heated air into the atmosphere. Scaling laws were used to preserve key aspects and to maintain similarity. The scaled air RCCS facility at UW-Madison is a quarter-scale reduced length experiment housing six riser ducts that represent a 9.5° sector slice of the full-scale GA air RCCS concept. Radiant heaters were used to simulate the heat radiation from the reactor pressure vessel. The maximum power that can be achieved with the radiant heaters is 40 kW with a peak heat flux of 25 kW per meter squared. The quarter-scale RCCS was run under different heat loading cases and operated successfully. Instabilities were observed in some experiments in which one of the two exhaust ducts experienced a flow reversal for a period of time. The data and analysis presented show that the RCCS has promising potential to be a decay heat removal system during an accident scenario.

Thermal-Hydraulic Analysis of an Experimental Reactor Cavity Cooling System with Air. Part I: Experiments; Part II: Separate Effects Tests and Modeling

Energy Technology Data Exchange (ETDEWEB)

Corradin, Michael [Univ. of Wisconsin, Madison, WI (United States). Dept. of Engineering Physics; Anderson, M. [Univ. of Wisconsin, Madison, WI (United States). Dept. of Engineering Physics; Muci, M. [Univ. of Wisconsin, Madison, WI (United States). Dept. of Engineering Physics; Hassan, Yassin [Texas A & M Univ., College Station, TX (United States); Dominguez, A. [Texas A & M Univ., College Station, TX (United States); Tokuhiro, Akira [Univ. of Idaho, Moscow, ID (United States); Hamman, K. [Univ. of Idaho, Moscow, ID (United States)

2014-10-15

This experimental study investigates the thermal hydraulic behavior and the heat removal performance for a scaled Reactor Cavity Cooling System (RCCS) with air. A quarter-scale RCCS facility was designed and built based on a full-scale General Atomics (GA) RCCS design concept for the Modular High Temperature Gas Reactor (MHTGR). The GA RCCS is a passive cooling system that draws in air to use as the cooling fluid to remove heat radiated from the reactor pressure vessel to the air-cooled riser tubes and discharged the heated air into the atmosphere. Scaling laws were used to preserve key aspects and to maintain similarity. The scaled air RCCS facility at UW-Madison is a quarter-scale reduced length experiment housing six riser ducts that represent a 9.5° sector slice of the full-scale GA air RCCS concept. Radiant heaters were used to simulate the heat radiation from the reactor pressure vessel. The maximum power that can be achieved with the radiant heaters is 40 kW with a peak heat flux of 25 kW per meter squared. The quarter-scale RCCS was run under different heat loading cases and operated successfully. Instabilities were observed in some experiments in which one of the two exhaust ducts experienced a flow reversal for a period of time. The data and analysis presented show that the RCCS has promising potential to be a decay heat removal system during an accident scenario.

Core disruptive accident margin seal

International Nuclear Information System (INIS)

Golden, M.P.

1979-01-01

An apparatus for sealing the annulus defined within a substantially cylindrical rotatable riser assembly and plug combination of a nuclear reactor closure head is described. The apparatus comprises an inflatable sealing mechanism disposed in one portion of the riser assembly near the annulus such that upon inflation the sealing mechanism is radially actuated against the other portion of the riser assembly thereby sealing the annulus. The apparatus further comprises a connecting mechanism which places one end of the sealing mechanism in fluid communication with the reactor cover gas so that overpressurization of the reactor cover gas will increase the radial actuation of the sealing mechanism thus enhancing sealing of the annulus

Kinetics of disorder-to-fcc phase transition via an intermediate bcc state

International Nuclear Information System (INIS)

Liu Yongsheng; Nie Huifen; Bansil, Rama; Steinhart, Milos; Bang, Joona; Lodge, Timothy P.

2006-01-01

Time-resolved small-angle x-ray scattering measurements reveal that a long-lived intermediate bcc state forms when a poly(styrene-b-isoprene) diblock copolymer solution in an isoprene selective solvent is rapidly cooled from the disordered micellar fluid at high temperature to an equilibrium fcc state. The kinetics of the epitaxial growth of the [111] fcc peak from the [110] bcc peak was obtained by fitting the scattering data to a simple model of the transformation. The growth of the [111] fcc peak agrees with the Avrami model of nucleation and growth kinetics with an exponent n=1.4, as does the initial decay of the [110] bcc peak, with an exponent n=1.3. The data were also found to be in good agreement with the Cahn model of grain boundary nucleation and growth

Communication government agencies: the case of FCC/ Organismos de regulación y control de las comunicaciones: el caso de la FCC

Directory of Open Access Journals (Sweden)

Dra. Ana I. Segovia Alonso; asegovia@ccinf.ucm.es

2009-01-01

Full Text Available The Federal Communications Commission (FCC is one of the pioneering regulatory agencies in relation to the communication system within the capitalist model. From a general perspective, beginning with its constitution, plan of action, and regulatory decisions, we carry out a research of the historical, political and economic conditions under which this commission operates and was created. The main objective is to outline the reasons for the failures and mistakes of the FCC, that has been accused –since its origins- of acting in defence of the industry interests it seemingly regulates, and not in the public interest; and of being a creature of Congress, with no real independence from the politic, economic, and judiciary power. The final purpose of this essay is to suggest the necessary democratization of the communicative space, which needs an agency transformation that could change the current defence of the existing status quo. La Comisión Federal de Comunicaciones (FCC es uno de los organismos pioneros en el control y regulación del sistema comunicativo en el modelo capitalista. Desde una mirada general a partir de su composición, formas de actuación, y decisiones normativas, se realiza un estudio de los condicionamientos históricos, políticos y económicos bajo los cuales se crea y desarrolla su labor esta Comisión. El objetivo fundamental es delinear las razones de los errores y negligencias de la FCC, acusada desde sus inicios de actuar en defensa de los intereses de la industria a la que pretende regular, y no en interés del público; y de ser una criatura del Congreso sin independencia del poder político, ni económico, ni judicial. El propósito final del presente artículo es plantear la necesaria democratización del espacio comunicativo, que pasa por una transformación de estos organismos y su defensa del status quo existente.

Epitaxial growth of fcc Ti films on Al(001) surfaces

International Nuclear Information System (INIS)

Saleh, A.A.; Shutthanandan, V.; Shivaparan, N.R.; Smith, R.J.; Tran, T.T.; Chambers, S.A.

1997-01-01

High-energy ion scattering (HEIS), x-ray photoelectron spectroscopy, and x-ray photoelectron diffraction (XPD) were used to study the growth of thin Ti films on Al(001) surfaces. The Al surface peak area in the backscattered ion spectrum of MeV He + ions, incident along the [00 bar 1] direction, was used to monitor the atomic structure of the Ti films during growth. An initial decrease in the area was observed indicating epitaxial film growth. This decrease continued up to a critical film thickness of about 5.5 ML, after which point the structure of the film changed. Titanium films 3, 5, and 9 ML thick were characterized using XPD in the same chamber. Both the HEIS and XPD results show that the Ti films grow with an fcc structure on Al(001). A tetragonal distortion of 2.4% in the fcc Ti film was measured using ions incident along the [10 bar 1] direction. Although there is a general similarity of fcc Ti growth on both Al(001) and Al(110), the submonolayer growth regime does show differences for the two surfaces. copyright 1997 The American Physical Society

First Design of a Proton Collimation System for 50 TeV FCC-hh

CERN Document Server

Fiascaris, Maria; Mirarchi, Daniele; Redaelli, Stefano

2016-01-01

We present studies aimed at defining a first conceptual solution for a collimation system for the hadron-hadron option for the Future Circular Collider (FCC-hh). The baseline collimation layout is based on the scaling of the present LHC collimation system to the FCC-hh energy. It currently includes a dedicated betatron cleaning insertion as well as collimators in the experimental insertions to protect the inner triplets. An aperture model for the FCC-hh is defined and the geometrical acceptance is calculated at top energy taking into account mechanical and optics imperfections. Based on these studies the collimator settings needed to protect the machine are defined. The performance of the collimation system is then assessed with particle tracking simulation tools assuming a perfect machine.

Hybrid Composite Tensile Armour Wires in Flexible Risers: A Multi-scale Model

OpenAIRE

Gautam, Mayank; Katnam, Kali-Babu; Potluri, Venkata; Jha, Vivekanand; Latto, J.; Dodds, NI

2017-01-01

Traditional carbon-steel armour wires pose limitations (e.g. long spans, weight reduction, corrosion and fatigue) for flexible risers to operate in demanding and deeper water environments. In this context, an alternative to carbon-steel tensile armour wires is proposed recently by the authors (Gautam et al. [1]), comprising of hexagonally packed polymer composite rods with uni-directional fibres and an over-braided (i.e. bi-axial braid with high performance fibres) sleeve. These hybrid compos...

Tapering Options and Emittance Fine Tuning for the FCC-ee Collider

OpenAIRE

Härer, Bastian; Doblhammer, Andreas; Holzer, Bernhard

2016-01-01

The lepton collider version of the FCC study describes a future electron-positron collider with a circumference in the order of 100 km, optimised for operation with collision energies in the range of 90 GeV to 350 GeV (FCC- ee). This paper presents the layout of the machine and the constraints on the design of the arc lattice in the context of the four different beam energies that are foreseen for beam operation. Special emphasis is put on the compensation of the effect of the strong synchrot...

Precision Electroweak measurements at the FCC-ee

CERN Document Server

Dam, Mogens

2016-01-01

Because of a luminosity of up to five orders of magnitude larger than at LEP, electroweak precision measurements at the FCC-ee -- the Future Circular Collider with electron-positron beams -- would provide improvements by orders of magnitude over the present status and constitute a broad search for the existence of new, weakly interacting particles up to very high energy scales. The FCC-ee will address centre-of-mass energies ranging from below the Z pole to the $\\mathrm{t\\bar{t}}$ threshold and above. At energies around the Z pole, the Z-boson mass and width can be measured to better than 100 keV each. Asymmetry measurements at the Z pole allow improvements in the determination of the weak mixing angle by at least a factor 30 to $\\delta\\sin^2\\theta\\mathrm{_W^{eff}}\\simeq 6\\times 10^{-6}$. A determination of the electromagnetic coupling constant at the Z energy scale, $\\alpha_\\mathrm{QED}(m_\\mathrm{Z}^2)$, to a relative precision of $3\\times 10^{-5}$ can be obtained via measurement of the forward-backward asym...

Design considerations and experimental observations for the TAMU air-cooled reactor cavity cooling system for the VHTR

Energy Technology Data Exchange (ETDEWEB)

Sulaiman, S. A., E-mail: shamsulamri@tamu.edu; Dominguez-Ontiveros, E. E., E-mail: elvisdom@tamu.edu; Alhashimi, T., E-mail: jbudd123@tamu.edu; Budd, J. L., E-mail: dubaiboy@tamu.edu; Matos, M. D., E-mail: mailgoeshere@gmail.com; Hassan, Y. A., E-mail: yhasssan@tamu.edu [Department of Nuclear Engineering, Texas A and M University, College Station, TX, 77843-3133 (United States)

2015-04-29

The Reactor Cavity Cooling System (RCCS) is a promising passive decay heat removal system for the Very High Temperature Reactor (VHTR) to ensure reliability of the transfer of the core residual and decay heat to the environment under all off-normal circumstances. A small scale experimental test facility was constructed at Texas A and M University (TAMU) to study pertinent multifaceted thermal hydraulic phenomena in the air-cooled reactor cavity cooling system (RCCS) design based on the General Atomics (GA) concept for the Modular High Temperature Gas-Cooled Reactor (MHTGR). The TAMU Air-Cooled Experimental Test Facility is ⅛ scale from the proposed GA-MHTGR design. Groundwork for experimental investigations focusing into the complex turbulence mixing flow behavior inside the upper plenum is currently underway. The following paper illustrates some of the chief design considerations used in construction of the experimental test facility, complete with an outline of the planned instrumentation and data acquisition methods. Computational Fluid Dynamics (CFD) simulations were carried out to furnish some insights on the overall behavior of the air flow in the system. CFD simulations assisted the placement of the flow measurement sensors location. Preliminary experimental observations of experiments at 120oC inlet temperature suggested the presence of flow reversal for cases involving single active riser at both 5 m/s and 2.25 m/s, respectively and four active risers at 2.25 m/s. Flow reversal may lead to thermal stratification inside the upper plenum by means of steady state temperature measurements. A Particle Image Velocimetry (PIV) experiment was carried out to furnish some insight on flow patterns and directions.

Inherited textures in the bcc phase furnish information about the type of transformation from the fcc phase

International Nuclear Information System (INIS)

Jung, V.

1982-07-01

Drawing annealed cylindric 18/8 Cr Ni steels, which are originally free of textures, produces the transformed phases - hcp and bcc - both showing major texture contributions with increasing stretching of the cylindric specimens. After stretching the original fcc-phase shows two orientations: [100]fcc vertical stroke vertical stroke cylinder axis and [111]fcc vertical stroke vertical stroke cylinder axis, i.e. direction of stress. In both cases the martensitic phase is produced by gliding and shear in the sequence fcc → hcp → bcc by Nishiyama-Wasserman (N-W) or Kurdjumov-Sachs (K-S) transformation in the (111)fcc planes, which enclose a small angle with direction of stress, i.e. cylinder axis. The calculated orientation distributions of the (110)bcc reflex are compared with the distribution measured by neutron diffraction to get information on the bulk material. The special K-S transformation with only 6 (110)bcc orientations shows relatively good agreement with the measured distribution, except at small angles ω between the cylinder axis and the scattering vector. This might be caused by the isotropic fraction of the fcc phase producing an anisotropic (110)bcc orientation distribution. (orig.) [de

76 FR 69738 - Revised 2011 Annual Telecommunications Reporting Worksheet (FCC Form 499-A) and Accompanying...

Science.gov (United States)

2011-11-09

... Telecommunications Reporting Worksheet (FCC Form 499-A) and Accompanying Instructions AGENCY: Federal Communications... Telecommunications Reporting Worksheet (FCC Form 499-A) and accompanying instructions that have been approved by the... INFORMATION CONTACT: Ernesto Beckford, Wireline Competition Bureau, Telecommunications Access Policy Division...

Nitrogen Chemistry and Coke Transformation of FCC Coked Catalyst during the Regeneration Process

Science.gov (United States)

Shi, Junjun; Guan, Jianyu; Guo, Dawei; Zhang, Jiushun; France, Liam John; Wang, Lefu; Li, Xuehui

2016-06-01

Regeneration of the coked catalyst is an important process of fluid catalytic cracking (FCC) in petroleum refining, however, this process will emit environmentally harmful gases such as nitrogen and carbon oxides. Transformation of N and C containing compounds in industrial FCC coke under thermal decomposition was investigated via TPD and TPO to examine the evolved gaseous species and TGA, NMR and XPS to analyse the residual coke fraction. Two distinct regions of gas evolution are observed during TPD for the first time, and they arise from decomposition of aliphatic carbons and aromatic carbons. Three types of N species, pyrrolic N, pyridinic N and quaternary N are identified in the FCC coke, the former one is unstable and tends to be decomposed into pyridinic and quaternary N. Mechanisms of NO, CO and CO2 evolution during TPD are proposed and lattice oxygen is suggested to be an important oxygen resource. Regeneration process indicates that coke-C tends to preferentially oxidise compared with coke-N. Hence, new technology for promoting nitrogen-containing compounds conversion will benefit the in-situ reduction of NO by CO during FCC regeneration.

Carbon flow analysis and Carbon emission reduction of FCC in Chinese oil refineries

Science.gov (United States)

Jia, Fengrui; Wei, Na; Ma, Danzhu; Liu, Guangxin; Wu, Ming; Yue, Qiang

2017-08-01

The major problem of the energy production in oil refineries is the high emission of CO2 in China. The fluid catalytic cracking unit (FCC) is the key source of carbon emission in the oil refineries. According to the statistical data, the carbon emission of FCC unit accounts for more than 31% for the typical oil refineries. The carbon flow of FCC in the typical Chinese oil refineries were evaluated and analysed, which aimed at the solution of CO2 emission reduction. The method of substances flow analysis (SFA) and the mathematical programming were used to evaluate the carbon metabolism and optimize the carbon emission. The results indicated that the combustion emission of the reaction-regeneration subsystem (RRS) was the major source of FCC. The quantity of CO2 emission of RSS was more than 90%. The combustion efficiency and the amount of residual oil affected the carbon emission of RRS most according to the optimized analysis of carbon emission reduction. Moreover, the fractionation subsystem (TFS) had the highest environmental efficiency and the absorption-stabilization subsystem (ASS) had the highest resource efficiency (approximately to 1) of carbon.

Precision measurement of the top quark mass at threshold with the FCC-ee

CERN Document Server

Foppiani, Nicolo

2016-01-01

The project concerns the study of the sensitivity in measuring the Top quark mass at threshold at the FCC-ee, using a Montecarlo analysis. In particular it has been developed within the FCC software framework, using a fast simulation. The work focused firstly on developing a b-tagging algorithm inside of the FCC fast simulation, managing to obtain results comparable with the ALEPH ones, and new results with a futuristic detector like ILD. Afterwards the selection of the tt events at energy close to the pair production threshold has been studied, obtaining a selection efficiency of 55 % and a background rejection at the level of 99.4 %. In the end, a list of points that can be achieved in the future, to complete the analysis, has been identified.

Direct measurement of α_Q_E_D(m_Z"2) at the FCC-ee

International Nuclear Information System (INIS)

Janot, Patrick

2016-01-01

When the measurements from the FCC-ee become available, an improved determination of the standard-model “input' parameters will be needed to fully exploit the new precision data towards either constraining or fitting the parameters of beyond-the-standard-model theories. Among these input parameters is the electromagnetic coupling constant estimated at the Z mass scale, α_Q_E_D(m_Z"2). The measurement of the muon forward-backward asymmetry at the FCC-ee, just below and just above the Z pole, can be used to make a direct determination of α_Q_E_D(m_Z"2) with an accuracy deemed adequate for an optimal use of the FCC-ee precision data.

Influence of cross-sectional ratio of down comer to riser on the efficiency of liquid circulation in loop air lift bubble column

Science.gov (United States)

Yamamoto, Tatsumi; Kawasaki, Hiroyuki; Mori, Hidetoshi

2017-11-01

Loop type bubble columns have good performance of liquid circulation and mass transfer by airlift effect, where the liquid circulation time is an important measurable characteristic parameter. This parameter is affected by the column construction, the aspect ratio of the column, the cross-sectional area ratio of down comer to riser (R), and the superficial gas velocity in the riser (UGR). In this work, the mean gas holdup and the liquid circulation time (TC) have been measured in four types of loop airlift type bubble column: concentric tube internal loop airlift type, rectangular internal loop airlift type, external loop airlift type, external loop airlift with separator. Air and tap water were used as gas and liquid phase, respectively. The results have demonstrated that the mean gas holdup in riser increases in proportion to UGR, and that it in downcomer changes according to the geometric parameters of each bubble column. TC has been found to conform to an empirical equation which depends on UGR and the length of draft tube or division plate in the region of 0.33 < R < 1.

Anisotropy in the inelastic neutron scattering from fcc NiH

International Nuclear Information System (INIS)

Antonov, V.E.; Fedotov, V.K.; Gnesin, B.A.; Kolesnikov, A.I.; Grosse, G.; Ivanov, A.S.; Wagner, F.E.

2000-01-01

A sample of nearly stoichiometric fcc nickel hydride in the form of polycrystalline plates with strong texture was studied by inelastic neutron scattering (INS) in two different orientations, with the [100] axis of the texture parallel and at an angle of 45 to the direction of neutron momentum transfer. The INS spectra were measured at 5 K with energy transfers ω ranging from 26 to 380 meV. In the region of the second and third band of optical hydrogen vibrations, they showed a significant directional dependence. A similar anisotropy was recently observed in the INS spectrum of fcc palladium hydride, and the now available data for NiH and PdH are discussed together. (orig.)

Proximal tibial fracture following anterior cruciate ligament reconstruction surgery: a biomechanical analysis of the tibial tunnel as a stress riser.

Science.gov (United States)

Aldebeyan, Wassim; Liddell, Antony; Steffen, Thomas; Beckman, Lorne; Martineau, Paul A

2017-08-01

This is the first biomechanical study to examine the potential stress riser effect of the tibial tunnel or tunnels after ACL reconstruction surgery. In keeping with literature, the primary hypothesis tested in this study was that the tibial tunnel acts as a stress riser for fracture propagation. Secondary hypotheses were that the stress riser effect increases with the size of the tunnel (8 vs. 10 mm), the orientation of the tunnel [standard (STT) vs. modified transtibial (MTT)], and with the number of tunnels (1 vs. 2). Tibial tunnels simulating both single bundle hamstring graft (8 mm) and bone-patellar tendon-bone graft (10 mm) either STT or MTT position, as well as tunnels simulating double bundle (DB) ACL reconstruction (7, 6 mm), were drilled in fourth-generation saw bones. These five experimental groups and a control group consisting of native saw bones without tunnels were loaded to failure on a Materials Testing System to simulate tibial plateau fracture. There were no statistically significant differences in peak load to failure between any of the groups, including the control group. The fracture occurred through the tibial tunnel in 100 % of the MTT tunnels (8 and 10 mm) and 80 % of the DB tunnels specimens; however, the fractures never (0 %) occurred through the tibial tunnel of the standard tunnels (8 or 10 mm) (P = 0.032). In the biomechanical model, the tibial tunnel does not appear to be a stress riser for fracture propagation, despite suggestions to the contrary in the literature. Use of a standard, more vertical tunnel decreases the risk of ACL graft compromise in the event of a fracture. This may help to inform surgical decision making on ACL reconstruction technique.

Faulted terrace risers place new constraints on the late Quaternary slip rate for the central Altyn Tagh fault, northwest Tibet

Science.gov (United States)

Gold, R.D.; Cowgill, E.; Arrowsmith, J.R.; Chen, X.; Sharp, W.D.; Cooper, K.M.; Wang, X.-F.

2011-01-01

The active, left-lateral Altyn Tagh fault defines the northwestern margin of the Tibetan Plateau in western China. To clarify late Quaternary temporal and spatial variations in slip rate along the central portion of this fault system (85??-90??E), we have more than doubled the number of dated offset markers along the central Altyn Tagh fault. In particular, we determined offset-age relations for seven left-laterally faulted terrace risers at three sites (Kelutelage, Yukuang, and Keke Qiapu) spanning a 140-km-long fault reach by integrating surficial geologic mapping, topographic surveys (total station and tripod-light detection and ranging [T-LiDAR]), and geochronology (radiocarbon dating of organic samples, 230Th/U dating of pedogenic carbonate coatings on buried clasts, and terrestrial cosmogenic radionuclide exposure age dating applied to quartz-rich gravels). At Kelutelage, which is the westernmost site (37.72??N, 86.67??E), two faulted terrace risers are offset 58 ?? 3 m and 48 ?? 4 m, and formed at 6.2-6.1 ka and 5.9-3.7 ka, respectively. At the Yukuang site (38.00??N, 87.87??E), four faulted terrace risers are offset 92 ?? 12 m, 68 ?? 6 m, 55 ?? 13 m, and 59 ?? 9 m and formed at 24.2-9.5 ka, 6.4-5.0 ka, 5.1-3.9 ka, and 24.2-6.4 ka, respectively. At the easternmost site, Keke Qiapu (38.08??N, 88.12??E), a faulted terrace riser is offset 33 ?? 6 m and has an age of 17.1-2.2 ka. The displacement-age relationships derived from these markers can be satisfied by an approximately uniform slip rate of 8-12 mm/yr. However, additional analysis is required to test how much temporal variability in slip rate is permitted by this data set. ?? 2011 Geological Society of America.

Two-riser system improves drilling at Auger prospect

International Nuclear Information System (INIS)

Gonzalez, R.; Marsh, G.L.; Ritter, P.B.; Mendel, P.E.

1992-01-01

This paper reports on a two-rise system (TRS) for drilling deepwater development wells which eliminates some of the limitations of conventional subsea technology and allows flexibility in well programs. Shell Offshore Inc.'s deep exploratory wells in Garden Banks 426 and 471 have encountered drilling problems that were attributed to limitations in casing sizes imposed by conventional subsea drilling systems. These problems are not uncommon in exploratory deepwater, deep well drilling in the Gulf of Mexico. Reservoir depths of up to 19,500 ft true vertical depth (TVD) and 7-in. production casing requirements led to potentially troublesome and expensive well plans. Because of the constraints placed on the development drilling program by completion requirements and directional drilling, a two-riser system was designed and fabricated. Solving such significant drilling problems has reduced overall development costs

Simulation of recrystallization textures in FCC materials based on a self consistent model

International Nuclear Information System (INIS)

Bolmaro, R.E; Roatta, A; Fourty, A.L; Signorelli, J.W; Bertinetti, M.A

2004-01-01

The development of re-crystallization textures in FCC polycrystalline materials has been a long lasting scientific problem. The appearance of the so-called cubic component in high stack fault energy laminated FCC materials is not an entirely understood phenomenon. This work approaches the problem using a self- consistent simulation technique of homogenization. The information on first preferential neighbors is used in the model to consider grain boundary energies and intra granular misorientations and to treat the growth of grains and the mobility of the grain boundary. The energies accumulated by deformations are taken as conducting energies of the nucleation and the later growth is statistically governed by the grain boundary energies. The model shows the correct trend for re-crystallization textures obtained from previously simulated deformation textures for high and low stack fault energy FCC materials. The model's topological representation is discussed (CW)

Stability analysis on natural circulation boiling water reactors

International Nuclear Information System (INIS)

Metz, Peter

1999-05-01

The purpose of the study is a stability analysis of the simplified boiling water reactor concept. A fluid dynamics code, DYNOS, was developed and successfully validated against FRIGG and DESIRE data and a stability benchmark on the Ringhals 1 forced circulation BWR. Three simplified desings were considered in the analysis: The SWRIOOO by Siemens and the SBWR and ESBWR from the General Electric Co. For all three design operational characteristics, i.e. power versus flow rate maps, were calculated. The effects which different geometric and operational parameters, such as the riser height, inlet subcooling etc., have on the characteristics have been investigated. Dynamic simulations on the three simplified design revealed the geysering and the natural circulation oscillations modes only. They were, however, only encountered at pressure below 0.6 MPa. Stability maps for all tree simplified BWRs were calculated and plotted. The study concluded that a fast pressurisation of the reactor vessel is necessary to eliminate the possibility of geysering or natural circulation oscillations mode instability. (au)

Core disruptive accident margin seal

International Nuclear Information System (INIS)

Garin, J.; Belsick, J.C.

1978-01-01

Disclosed is an apparatus for sealing the annulus defined between a substantially cylindrical rotatable first riser assembly and plug combination disposed in a substantially cylindrical second riser assembly and plug combination of a nuclear reactor system. The apparatus comprises a flexible member disposed between the first and second riser components and attached to a metal member which is attached to an actuating mechanism. When the actuating mechanism is not actuated, the flexible member does not contact the riser components thus allowing the free rotation of the riser components. When desired, the actuating mechanism causes the flexible member to contact the first and second riser components in a manner to block the annulus defined between the riser components, thereby sealing the annulus between the riser components

ALARA plan for the Old Hydrofracture Facility tanks contents removal project at Oak Ridge National Laboratory, Oak Ridge, Tennessee. Amendment 1 for Appendix B: Install flex-pipe on tank riser spools

International Nuclear Information System (INIS)

1998-01-01

This amendment to Appendix B contains the specific ALARA evaluations for installing flex-pipe on riser spools to accommodate ventilation duct connections to the north risers of each tank. The work will be a routine task that is part of the Equipment Installation and Mobilization phase of the project. The dose rates were estimated using the recent Radiological Surveillance Section radiological survey: SAAS-97-063S. Task B-6 has been added to the OHF Project ALARA review process to address a field decision to modify an approach to installing the tank ventilation system. The revised approach will incorporate 12-in. diameter, 36-in. long, stainless steel flex-pipe connected to each north riser spool to address the problem of pipe fitting multiple bends and turns expected with the 12-in. PVC duct. This improved approach will reduce the time necessary to install the duct system between the tanks and the ventilation skid. However, the task includes opening the 12-in. riser spool connections to replace the currently installed blind gaskets. Since a riser spool for each tank will be opened, there is a potential for significant personnel exposure and spread of contamination that will addressed through this ALARA review process

Kinetics of self-interstitial migration in bcc and fcc transition metals

Science.gov (United States)

Bukkuru, S.; Bhardwaj, U.; Srinivasa Rao, K.; Rao, A. D. P.; Warrier, M.; Valsakumar, M. C.

2018-03-01

Radiation damage is a multi-scale phenomenon. A thorough understanding of diffusivities and the migration energies of defects is a pre-requisite to quantify the after-effects of irradiation. We investigate the thermally activated mobility of self-interstitial atom (SIA) in bcc transition metals Fe, Mo, Nb and fcc transition metals Ag, Cu, Ni, Pt using molecular dynamics (MD) simulations. The self-interstitial diffusion involves various mechanisms such as interstitialcy, dumbbell or crowdion mechanisms. Max-Space Clustering (MSC) method has been employed to identify the interstitial and its configuration over a wide range of temperature. The self-interstitial diffusion is Arrhenius like, however, there is a slight deviation at high temperatures. The migration energies, pre-exponential factors of diffusion and jump-correlation factors, obtained from these simulations can be used as inputs to Monte Carlo simulations of defect transport. The jump-correlation factor shows the degree of preference of rectilinear or rotational jumps. We obtain the average jump-correlation factor of 1.4 for bcc metals and 0.44 for fcc metals. It indicates that rectilinear jumps are preferred in bcc metals and rotational jumps are preferred in fcc metals.

Cesium under pressure: First-principles calculation of the bcc-to-fcc phase transition

Science.gov (United States)

Carlesi, S.; Franchini, A.; Bortolani, V.; Martinelli, S.

1999-05-01

In this paper we present the ab initio calculation of the structural properties of cesium under pressure. The calculation of the total energy is done in the local-density approximation of density-functional theory, using a nonlocal pseudopotential including the nonlinear core corrections proposed by Louie et al. The calculation of the pressure-volume diagram for both bcc and fcc structures allows us to prove that the transition from bcc to fcc structure is a first-order transition.

Pressure-induced structural change from hexagonal to fcc metal lattice in scandium trihydride

International Nuclear Information System (INIS)

Ohmura, A.; Machida, A.; Watanuki, T.; Aoki, K.; Nakano, S.; Takemura, K.

2007-01-01

We synthesized scandium hydrides by hydrogenation of a scandium foil with hydrogen fluid under high pressure at ambient temperature. Scandium dihydride (ScH 2 ) and trihydride (ScH 3 ) were prepared near 4 and 5 GPa, respectively. The hydrogenation process and pressure-induced structural changes in ScH 3 were investigated by synchrotron radiation X-ray diffraction measurements up to 54.7 GPa. A structural transition from hexagonal to the fcc lattice began at 30 GPa and was completed at 46 GPa via an intermediate state similar to those reported for other hexagonal trihydrides. The intermediate state was not interpreted in terms of a coexisting state for the low-pressure hexagonal and the high-pressure fcc structures. The onset transition pressure of ScH 3 supported the previously proposed relation that the hexagonal-fcc transition pressure is inversely proportional to the ionic radius of the trihydride

Production and characterization of bio-oil from catalytic biomass pyrolysis

Directory of Open Access Journals (Sweden)

Antonakou Eleni V.

2006-01-01

Full Text Available Biomass flash pyrolysis is a very promising thermochemical process for the production of bio-fuels and/or chemicals. However, large-scale applications are still under careful consideration, because of the high bio-liquid upgrading cost. In this paper the production of bio-liquids from biomass flash pyrolysis in a single stage catalytic process is being investigated using a novel once through fluid bed reactor. This biomass pyrolysis unit was constructed in Chemical Process Engineering Research Institute and comprises of a catalyst regenerator, a biomass-vibrating hopper, a fluidization reactor (that consists of an injector and a riser reactor, a product stripper along with a hot cyclone and a filter housing and finally a product condensation/recovery section. The unit can process up to 20 g/min. of biomass (50-800 mm and can circulate up to 300 g/min. of catalyst or inert material. The experiments performed in the pilot plant showed that the unit operates without problems and with satisfactory mass balances in a wide range of experimental conditions both in the absence and presence of catalyst. With the incorporation of an FCC catalyst in the pyrolysis, the physical properties of the bio-oil produced changed, while more stable bio-oil was produced. .

Pseudomorphic-to-bulk fcc phase transition of thin Ni films on Pd(100)

International Nuclear Information System (INIS)

Rizzi, G.A.; Petukhov, M.; Sedona, F.; Granozzi, G.; Cossaro, A.; Bruno, F.; Cvetko, D.; Morgante, A.; Floreano, L.

2004-01-01

We have measured the transformation of pseudomorphic Ni films on Pd(100) into their bulk fcc phase as a function of the film thickness. We made use of x-ray diffraction and x-ray induced photoemission to study the evolution of the Ni film and its interface with the substrate. The growth of a film with tetragonally strained face centered symmetry (fct) has been observed by out-of-plane x-ray diffraction up to a limit thickness of 10 Ni pseudomorphic layers (some of them partially filled and intermixed with the substrate), where a new fcc bulklike phase is formed. After the formation of the bulklike Ni domains, we observed the pseudomorphic fct domains to disappear preserving the number of layers and their spacing. The phase transition thus proceeds via lateral growth of the bulklike phase within the pseudomorphic one, i.e., the bulklike fcc domains penetrate down to the substrate when formed. This large depth of the walls separating the domains of different phases is also indicated by the increase of the intermixing at the substrate-film interface, which starts at the onset of the transition and continues at even larger thickness. The bulklike fcc phase is also slightly strained; its relaxation towards the orthomorphic lattice structure proceeds slowly with the film thickness, being not yet completed at the maximum thickness presently studied of 30 A (∼17 layers)

Estudo do efeito de um "Riser Blowout" na perfuração de poços de petroleo em aguas profundas

OpenAIRE

Heitor Rodrigues de Paula Lima

1991-01-01

Resumo: Esta dissertação apresenta uma análise do comportamento da pressão dos fluidos que ocorre durante o especial acidente na perfuração de um poço submarino de petróleo conhecido como "Riser Blowout" ( * ). O modelo usado neste estudo baseia-se na solução do sistema de equações diferenciais parciais que governam o fluxo ascendente da mistura bifásica fluido de perfuração/ gás dentro do espaço anular entre a coluna de perfuração e o "marine riser". As perdas de carga devido a aceleração do...

Comportement mécanique des tuyaux. Influence de la traction, de la pression et du poids linéique. Application aux risers Mechanical Behavior of Pipes and Risers. Influence of Tension, Pressure and Weight

Directory of Open Access Journals (Sweden)

Sparks C.

2006-11-01

Full Text Available L'influence de la traction, de la pression et du poids linéique sur le comportement d'un tuyau (ou d'un riser a déjà été traitée dans de nombreux articles. Malgré cela, elle est fréquemment mal comprise, ce qui a parfois de; conséquences sérieuses. Par souci de clarté, l'approche de cet article est délibérément très élémentaire. Les problèmes principaux de la flexion, du flambage, de l'allongement et de la contrainte limite, qui sont souvent traités dans des articles différents, sont ici étudiés ensemble d'une façon homogène. On présente des interprétation: physiques, faciles à visualiser, des deux concepts de tension effective et de contrainte effective, dont l'utilisation est très répandue, ainsi que leur rapport avec des notions analogues dans d'autres domaines de l'art de l'ingénieur. La puissance de ces deux concepts est démontrée à la fin de l'article où ils sont utilisés pour résoudre huit problèmes divers. The influence of tension, pressure, and weight on different aspects of pipe and riser behavior has already been the subject of many articles (see references. In spite of this it has frequently been misunderstood, sometimes with serious consequences. The object of this payer is to explain the subject clearly and the approach is therefore deliberately very elementary. The principal problems of bending, buckling, yielding and strains, usually treated in separated papers, are here treated homogeneously. The widely used concepts of effective tension and effective stress are given interpretations, easy to visualise, which are related to analogous concepts in other engineering fields. Finally, eight diverse particular examples of the influence of tension, pressure and weight on pipe and riser behavior, are discussed.

Multidimensional analysis of developing two-phase flows in an ESBWR chimney with and without riser channels

International Nuclear Information System (INIS)

Murakawa, H.; Antal, S.P.; Lahey, R T.

2008-01-01

The object of this work was to simulate developing multidimensional velocity and void fraction distributions in bubbly and churn turbulent two-phase flows. An advanced Computational Multiphase Fluid Dynamics (CMFD) code, NPHASE, was used to perform three-dimensional, multi-field simulations of the developing phasic velocity and phase distributions in vertical adiabatic conduits. The NPHASE code employed a multi-field two-fluid model, in which, for churn turbulent flow, the vapor phase was divided into small and large, cap bubble fields. In addition, state-of-the-art interfacial area density and field-to-field mass transfer models were used for both the small and large, cap bubbles. In particular, the bubble breakup and coalescence processes were quantified using a two-group interfacial area density transport equation. This allowed the CMFD simulation of developing churn turbulent flows in an ESBWR with and without vertical riser channels in the chimney region above the core. Based on these simulations it was concluded that riser channels have little adverse effect on the induced natural circulation flow through the core and the stability characteristics of an ESBWR. (authors)

Investigating effects of BCC and FCC arrangements on flow and heat transfer characteristics in pebbles through CFD methodology

Energy Technology Data Exchange (ETDEWEB)

Ferng, Yuh Ming, E-mail: ymferng@ess.nthu.edu.tw [Department of Engineering and System Science, Institute of Nuclear Engineering and Science, National Tsing Hua University, 101, Sec. 2. Kuang-Fu Rd., Hsingchu 30013, Taiwan, ROC (China); Lin, Kun-Yueh [Department of Engineering and System Science, Institute of Nuclear Engineering and Science, National Tsing Hua University, 101, Sec. 2. Kuang-Fu Rd., Hsingchu 30013, Taiwan, ROC (China)

2013-05-15

Highlights: ► An HTGR would be one of the possible energy generation sources. ► We propose a CFD model to study effects of pebble arrangements for a PRB core. ► The entrance effect on the Nu number can be reasonably captured. ► The present predicted Nu versus Re{sub p} shows good agreement with data and correlation. ► Using FCC lattice in a core, simulation results may be non-conservative. -- Abstract: A high temperature gas cooled reactor (HTGR) would be one of the possible energy generation sources due to its advantages of inherently safety performance and higher conversion efficiency, etc. However, safety is the most important issue for its commercialization in energy industry. It is very crucial for safety design and operation of an HTGR to investigate its thermal–hydraulic characteristics. In this article, a computational fluid dynamics (CFD) methodology is proposed to investigate effects of different arrangements on these characteristics for an HTGR with a pebble bed (PB) core. Two kinds of arrangement: body-centered cubic (BCC) and face-centered cubic (FCC) are studies herein. Based on the simulation results, higher heat transfer capability and lower pebble temperature are predicted in the pebbles with the FCC-arrangement. The thermally fully-developed flow condition may be reached, which is shown in the result that the predicted average Nussel (Nu) number decreases from the 1st layer and reaches to an asymptotic value as the gas passes through the 6th layer of pebbles. This entrance effect reveals that the system codes using the correlations developed from the fully-developed flow condition can be appropriately applied in the entire PBR core. In addition, the present predicted dependence of Nu number on the inlet Reynolds (Re) number shows good agreement with that obtained from the well-known KTA. Measured data of Nu number versus Re number are also used to validate the CFD model.

Impact Of Particle Agglomeration On Accumulation Rates In The Glass Discharge Riser Of HLW Melter

International Nuclear Information System (INIS)

Kruger, A. A.; Rodriguez, C. A.; Matyas, J.; Owen, A. T.; Jansik, D. P.; Lang, J. B.

2012-01-01

The major factor limiting waste loading in continuous high-level radioactive waste (HLW) melters is an accumulation of particles in the glass discharge riser during a frequent and periodic idling of more than 20 days. An excessive accumulation can produce robust layers a few centimeters thick, which may clog the riser, preventing molten glass from being poured into canisters. Since the accumulation rate is driven by the size of particles we investigated with x-ray microtomography, scanning electron microscopy, and image analysis the impact of spinel forming components, noble metals, and alumina on the size, concentration, and spatial distribution of particles, and on the accumulation rate. Increased concentrations of Fe and Ni in the baseline glass resulted in the formation of large agglomerates that grew over the time to an average size of ∼185+-155 μm, and produced >3 mm thick layer after 120 h at 850 deg C. The noble metals decreased the particle size, and therefore significantly slowed down the accumulation rate. Addition of alumina resulted in the formation of a network of spinel dendrites which prevented accumulation of particles into compact layers

Sulfur and octane trade off in FCC naphta conventional hydrotreating

Energy Technology Data Exchange (ETDEWEB)

Badra, C. [INTEVEP S.A. Research and Technological Support Center of Petroleos de Venzuela, Caracas (Venezuela). Dept. de Refinacion; Perez, J.A. [INTEVEP S.A. Research and Technological Support Center of Petroleos de Venzuela, Caracas (Venezuela). Dept. de Refinacion; Salazar, J.A. [INTEVEP S.A. Research and Technological Support Center of Petroleos de Venzuela, Caracas (Venezuela). Dept. de Refinacion; Cabrera, L. [INTEVEP S.A. Research and Technological Support Center of Petroleos de Venzuela, Caracas (Venezuela). Dept. de Refinacion; Gracia, W. [INTEVEP S.A. Research and Technological Support Center of Petroleos de Venzuela, Caracas (Venezuela). Dept. de Refinacion

1997-06-01

A model to predict the change of octane numbers expected in an FCC naphtha hydrotreating process as a function of the hydroprocessing severity (degree of sulfur removal) and the type of naphtha (expressed as the sulfur content and bromine number in the feedstock) is presented. When considering hydrotreating as an option for processing their catalytic naphthas, refiners search for the proper balance between the desired reduction of sulfur and olefins and the resulting undesired reduction of octane (RON and MON). In doing so, refiners should study the possibility of performing the hydrotreating at mild severities and/or the possibility of fractionating FCC naphthas to just treat a specific cut. This paper provides simple tools to study and analyze these study cases and to assess the sulfur-octane trade offs. (orig.)

Experimental study of the spin density of metastable fcc ferromagnetic Fe-Cu alloys

International Nuclear Information System (INIS)

Bove, L. E.; Petrillo, C.; Sacchetti, F.; Mazzone, G.

2000-01-01

Magnetization density measurements on metastable Fe x Cu 1-x alloys at four compositions (x=20, 40, 50, and 60 at. %) and at 5 K temperature were carried out by means of polarized neutron diffraction. The samples were produced by high-energy ball milling and characterized by x-ray diffraction and fluorescence measurements. Additional bulk magnetization measurements were carried out on the two samples at high Fe concentration. Over the present concentration region, the Fe-Cu system is ferromagnetic and the four samples were found to be in the fcc phase. Fe-Cu is therefore a very suitable system to investigate the magnetic state of Fe in an fcc environment. Other than confirming that the Fe-Cu system is not a simple dilution alloy, the present results were compatible with a two-state model for fcc Fe--that is, two different coexisting electronic states associated with different magnetic moments and form factors

Updates on the optics of the future hadron-hadron collider FCC-hh

CERN Document Server

AUTHOR|(CDS)2093721; Boutin, David Jean Henri; Dalena, Barbara; Holzer, Bernhard; Langner, Andy Sven; Schulte, Daniel

2017-01-01

The FCC-hh (Future Hadron-Hadron Circular Collider) is one of the three options considered for the next generation accelerator in high-energy physics as recommended by the European Strategy Group. The layout of FCC-hh has been optimized to a more compact design following recommendations from civil engineering aspects. The updates on the first order and second order optics of the ring will be shown for collisions at the required centre-of-mass energy of 100 TeV. Special emphasis is put on the dispersion suppressors and general beam cleaning sections as well as first considerations of injection and extraction sections.

Numerical simulation and experimental analysis for a Risers Uphold Sub-Surface Buoy (BSR); Simulacao numerica e ensaio experimental da Boia de Sub-superficie de Suporte de Risers - BSSR

Energy Technology Data Exchange (ETDEWEB)

Araujo, Jairo B. de; Almeida, Jose Carlos L. de [PETROBRAS, Rio de Janeiro, RJ (Brazil); Rangel, Marcos; Fernandes, Antonio C.; Santos, Melquisedec F. dos; Sales Junior, Joel Sena [Universidade Federal do Rio de Janeiro (UFRJ), RJ (Brazil). Coordenacao dos Programas de Pos-graduacao de Engenharia (COPPE)

2004-07-01

This paper presents results, numeric and experimental, due to installation operation of a Risers Uphold Sub-Surface Buoy, (BSR). This kind of installation developed by PETROBRAS is unique in the world. The work of BSR installation was based on a numeric pre analysis to verify the system and determine the main parameters to be experimentally verified. The second phase of the work was the experimental analysis in a deep water ocean basin. s. The work describes the BSR and their main accessories, the experimental environment and the model constructed in aluminum in a 1:12 scale and the main results. (author)

75 FR 26091 - Safety Zone; Riser for DEEPWATER HORIZON at Mississippi Canyon 252 Outer Continental Shelf MODU...

Science.gov (United States)

2010-05-11

... the Gulf of Mexico AGENCY: Coast Guard, DHS. ACTION: Temporary final rule. SUMMARY: The Coast Guard is... personnel involved in oil pollution response efforts. Placing a safety zone around the riser will... the water's surface and subsurface. DATES: Effective Date: This rule is effective in the CFR on May 11...

Quantitative comparison between simulated and experimental FCC rolling textures

DEFF Research Database (Denmark)

Wronski, M.; Wierzbanowski, K.; Leffers, Torben

2015-01-01

The degree of similarity between simulated and experimental fcc rolling textures is characterized by a single scalar parameter. The textures are simulated with a relatively simple and efficient 1-point model which allows us to vary the strength of the interaction between the grains and the surrou...

Deformation microstructure and orientation of F.C.C. crystals

DEFF Research Database (Denmark)

Liu, Q.; Hansen, N.

1995-01-01

The effect of crystallographic orientation on the microstructural evolution in f.c.c. metals with medium to high stacking fault energy is analyzed. This analysis is based on a literature review of the behaviour of single crystals and polycrystals supplemented with an experimental study of cold...

Maximizing light olefins production in fluid catalytic cracking (FCC) units; Maximizacao de olefinas leves em unidades de craqueamento catalitico fluido

Energy Technology Data Exchange (ETDEWEB)

Pimenta, Ricardo D.M.; Pinho, Andrea de Rezende [PETROBRAS, Rio de Janeiro, RJ (Brazil)

2004-07-01

The Fluid Catalytic Cracking (FCC) process is widely spread over the ten PETROBRAS refineries in its thirteen industrial units. The importance of the FCC process resides on its high gasoline output, being the main supplier of this important product to the system. Additionally, FCC process is the main source of light hydrocarbons in the LPG range, including light olefins. The increasing demand for ethylene, propylene and butylenes was encouraging to concentrate the research efforts on studies about alternatives for the traditional FCC process. In the present work, the proposals from main licensors (UOP, KBR, Stone and Webster) for a light-olefins-driven FCC process (Petrochemical FCC) will be compared. Furthermore, the catalytic route for light olefins production in FCC units is also described. An additive based on ZSM- 5 zeolite, which is produced following a PETROBRAS proprietary technology, is being largely applied into the catalyst inventories of all FCC units. An analysis of different scenarios was performed to estimate the maximum potential of light olefins production from the highest possible ZSM-5 additive usage. More specifically for the case of ethylene, which production is also boosted by the same type of additive, studies are being conducted with the objective of recovering it from a C2 stream using specific units to do the splitting (UPGR). The search for increasing light olefins production in the refining processes is in line with PETROBRAS strategic plan which targeted for the company a more intense activity in the Brazilian petrochemical market (author)

Dynamic Aperture Studies for the FCC-ee

CERN Document Server

Medina, L; Tomas, R; Zimmermann, F

2015-01-01

Dynamic aperture (DA) studies have been conducted on the latest Future Circular Collider – ee (FCC-ee) lattices as a function of momentum deviation.Two different schemes for the interaction region are used, which are connected to the main arcs: the crab waist approach, developed by BINP, and an update to the CERN design where the use of crab cavities is envisioned. The results presented show an improvement in the performance of both designs.

Beam-beam studies for FCC-hh

CERN Document Server

AUTHOR|(CDS)2068329; Pieloni, Tatiana; Buffat, Xavier; Furuseth, Sondre Vik

2017-01-01

The Future Circular Collider hadron-hadron (FCC-hh) design study is currently exploring different IR design possibilities including round and flat optics or different crossing schemes. The present study intends to evaluate each scenario from the beam-beam effects point of view. In particular the single particle long term stability to maximize beam lifetimes and luminosity reach is used to quantify the differences. The impact of strong head on interactions on the beam quality and lifetime is addressed by means of GPU accelerated simulations code featuring a weak-strong 6-dimensional beam-beam interaction.

75 FR 62818 - Sunshine Act Meeting; FCC To Hold Open Commission Meeting Thursday, October 14, 2010

Science.gov (United States)

2010-10-13

... changes to the FCC's CableCARD rules to improve the consumer experience with the video navigation devices... Connection also will carry the meeting live via the Internet. To purchase these services call (703) 993-3100... purchased from the FCC's duplicating contractor, Best Copy and Printing, Inc. (202) 488-5300; Fax (202) 488...

Learning control for riser-slug elimination and production-rate optimization for an offshore oil and gas production process

DEFF Research Database (Denmark)

Pedersen, Simon; Løhndorf, Petar Durdevic; Yang, Zhenyu

2014-01-01

, (ii) maximizing the production rate at the riser of an offshore production platform, by manipulating a topside choke valve through a learning switching model-free PID controller. The results show good steady-state performance, though a long settling time due to the unknown reference for no slugging...

A new f.c.c. phase in yttrium films

International Nuclear Information System (INIS)

Kaul, V.K.; Srivastava, O.N.

1976-01-01

A new polymorphic phase characterised by a face-centered cubic structure, with lattice parameter 5.83 +- 0.02A, has been identified in thin films of yttrium. Electron diffraction evidence and electrical resistivity measurements have been carried out in order to detect the new f.c.c. phase. (Auth.)

A newly developed maneuver, field change conversion (FCC), improved evaluation of the left ventricular volume more accurately on quantitative gated SPECT (QGS) analysis

International Nuclear Information System (INIS)

Tajima, Osamu; Shibasaki, Masaki; Hoshi, Toshiko; Imai, Kamon

2002-01-01

The purpose of this study was to investigate whether a newly developed maneuver that reduces the reconstruction area by a half more accurately evaluates left ventricular (LV) volume on quantitative gated SPECT (QGS) analysis. The subjects were 38 patients who underwent left ventricular angiography (LVG) followed by G-SPECT within 2 weeks. Acquisition was performed with a general purpose collimator and a 64 x 64 matrix. On QGS analysis, the field magnification was 34 cm in original image (Original: ORI), and furthermore it was changed from 34 cm to 17 cm to enlarge the re-constructed image (Field Change Conversion: FCC). End-diastolic volume (EDV) and end-systolic volume (ESV) of the left ventricle were also obtained using LVG. EDV was 71±19 ml, 83±20 ml and 98±23 ml for ORI, FCC and LVG, respectively (p<0.001: ORI versus LVG, p<0.001: ORI versus FCC, p<0.001: FCC versus LVG). ESV was 28±12 ml, 34±13 ml and 41±14 ml for ORI, FCC and LVG, respectively (p<0.001: ORI versus LVG, p<0.001: ORI versus FCC, p<0.001: FCC versus LVG). FCC was better than ORI for calculating LV volume in clinical cases. Furthermore, FCC is a useful method for accurately measuring the LV volume on QGS analysis. (author)

Prediction of physicochemical properties of FCC feedstock by Chemometric analysis of their ultraviolet spectrum

International Nuclear Information System (INIS)

Baldrich Ferrer, Carlos A

2008-01-01

Chemometric analysis by Partial Least Squares (PLS) has been applied in this work to correlate the ultraviolet spectrum of combined Fluid Catalytic Cracking (FCC) feedstock with their physicochemical properties. The prediction errors obtained in the validation process using refinery samples demonstrate the accuracy of the predicted properties. This new analytical methodology allows obtaining in one analysis detailed information about the most important physicochemical properties of FCC feedstock and could be used as a valuable tool for operational analysis

Growth of metastable fcc Mn thin film on GaAs(001) and its electronic structure studied by photoemission with synchrotron radiation

International Nuclear Information System (INIS)

Chen Yan; Dong Guosheng; Zhang Ming

1995-01-01

The epitaxial growth of metastable fcc Mn thin films on GaAs(001) surface has been achieved at a substrate temperature of 400 K. The development of the fcc Mn thin films as a function of coverage is studied by photoemission with synchrotron radiation. The electron density of states below the Fermi edge of the fcc Mn phase is measured. A significant difference of the electronic structures is observed between the metastable fcc Mn phase and the thermodynamically stable α-Mn phase. Possible mechanisms are proposed to interpret the experimental result

GENIUS & the Swedish Fast Reactor programme

International Nuclear Information System (INIS)

Wallenius, Janne

2012-01-01

Concluding remarks: Sweden’s growing fast reactor programme focuses on LFR technology, but we also participate in ASTRID. • An innovative facility for UN fabrication, an LBE thermal hydraulics loop and a lead corrosion facility are operational. • A plutonium fuel fabrication lab is is under installation (this week!) • The government is assessing the construction of ELECTRA-FCC, a centre for Gen IV-system R&D, at a tentative cost of ~ 140±20 M€. • Location: Oskarshamn (adjacent to intermediate repository) • Date of criticality: 2023 (best case) • Swedish participation in IAEA TWG-FR should intensify

Diffusivities and atomic mobilities in Cu-rich fcc Al-Cu-Mn alloys

Energy Technology Data Exchange (ETDEWEB)

Yin, Ming; Du, Yong; Cui, Senlin; Xu, Honghui; Liu, Shuhong [Central South Univ., Changsha (China). State Key Laboratory of Powder Metallurgy; Zhang, Lijun [Bochum Univ. (DE). Interdisciplinary Centre for Advanced Materials Simulation (ICAMS)

2012-07-15

Via solid-solid diffusion couples, electron probe microanalysis and the Whittle and Green method, interdiffusivities in fcc Al-Cu-Mn alloys at 1 123 K were measured. The reliability of the obtained diffusivities is validated by comparing the computed diffusivities with literature data plus constraints among the diffusivities. Through assessments of experimentally determined diffusion coefficients by means of a diffusion-controlled transformations simulation package, the atomic mobilities of Al, Cu, and Mn in fcc Al-Cu-Mn alloys are obtained. Comprehensive comparisons between the model-predicted and the experimental data indicate that the presently obtained atomic mobilities can reproduce most of the diffusivities, concentration profiles, and diffusion paths reasonably. (orig.)

Ternary diffusion in Cu-rich fcc Cu–Al–Si alloys at 1073 K

Energy Technology Data Exchange (ETDEWEB)

Liu, Dandan [School of Materials Science and Engineering, Central South University, Changsha, Hunan 410083 (China); State Key Laboratory of Powder Metallurgy, Central South University, Changsha, Hunan 410083 (China); Zhang, Lijun [State Key Laboratory of Powder Metallurgy, Central South University, Changsha, Hunan 410083 (China); Du, Yong, E-mail: yongducalphad@gmail.com [State Key Laboratory of Powder Metallurgy, Central South University, Changsha, Hunan 410083 (China); Xu, Honghui [State Key Laboratory of Powder Metallurgy, Central South University, Changsha, Hunan 410083 (China); Jin, Zhanpeng [School of Materials Science and Engineering, Central South University, Changsha, Hunan 410083 (China)

2013-07-25

Highlights: •Interdiffusivities in Cu-rich fcc Cu–Al–Si alloys at 1073 K were determined. •The present results were compared with experimental data in boundary binary systems. •The present results were validated by thermodynamic constraints and Fick’s law. •The sign of ternary cross diffusivities was predicted in terms of thermodynamics. -- Abstract: Utilizing six groups of bulk diffusion couples and with electron probe microanalysis technique, the composition dependence of ternary interdiffusion coefficients in Cu-rich fcc Cu–Al–Si alloys at 1073 K were determined by the Matano-Kirkaldy method. Using a three-dimensional representation, the obtained main ternary diffusion coefficients were found to be consistent with the experimental data in boundary binaries available in the literature. The reliability of the obtained interdiffusivities was further validated by thermodynamic constraints as well as by Fick’s second law applied to numerical simulation. The sign of the ternary cross diffusivities in fcc Cu–Al–Si alloys, which shows a noticeable effect on microstructure, was also successfully predicted in terms of thermodynamics.

Ternary diffusion in Cu-rich fcc Cu–Al–Si alloys at 1073 K

International Nuclear Information System (INIS)

Liu, Dandan; Zhang, Lijun; Du, Yong; Xu, Honghui; Jin, Zhanpeng

2013-01-01

Highlights: •Interdiffusivities in Cu-rich fcc Cu–Al–Si alloys at 1073 K were determined. •The present results were compared with experimental data in boundary binary systems. •The present results were validated by thermodynamic constraints and Fick’s law. •The sign of ternary cross diffusivities was predicted in terms of thermodynamics. -- Abstract: Utilizing six groups of bulk diffusion couples and with electron probe microanalysis technique, the composition dependence of ternary interdiffusion coefficients in Cu-rich fcc Cu–Al–Si alloys at 1073 K were determined by the Matano-Kirkaldy method. Using a three-dimensional representation, the obtained main ternary diffusion coefficients were found to be consistent with the experimental data in boundary binaries available in the literature. The reliability of the obtained interdiffusivities was further validated by thermodynamic constraints as well as by Fick’s second law applied to numerical simulation. The sign of the ternary cross diffusivities in fcc Cu–Al–Si alloys, which shows a noticeable effect on microstructure, was also successfully predicted in terms of thermodynamics

HDPE (High Density Polyethylene) pipeline and riser design in Guanabara Bay: challenges and solutions

Energy Technology Data Exchange (ETDEWEB)

Bomfimsilva, Carlos; Jorge, Joao Paulo Carrijo; Schmid, Dominique; Gomes, Rodrigo Klim [INTECSEA, Sao Paulo, SP (Brazil); Lima, Alexander Piraja [GDK, Salvador, BA (Brazil)

2009-12-19

Worldwide shipments of plastic pipes are forecasted to increase 5.2% per year since 2008, being commonly used for water supply and sewage disposal. The HDPE (High Density Polyethylene) pipes have been applied recently to deliver potable water and fire fighting water for the main pier of the LNG system in Guanabara Bay, Rio de Janeiro. The system contains three sizes of pipe outside diameter, 110 mm and 160 mm for water supply, and 500 mm for the fire fighting system. The main design challenges of the pipeline system included providing on-bottom stability, a suitable installation procedure and a proper riser design. The on-bottom stability calculations, which are quite different from the conventional steel pipelines, were developed by designing concrete blocks to be assembled on the pipeline in a required spacing to assure long term stability, knowing that plastic pipes are buoyant even in flooded conditions. The installation procedure was developed considering the lay down methodology based on surface towing technique. The riser was designed to be installed together with additional steel support structure to allow the entire underwater system to have the same plastic pipe specification up to the surface. This paper presents the main challenges that were faced during the design of the HDPE pipelines for the LNG system in Guanabara Bay, addressing the solutions and recommendations adopted for the plastic underwater pipeline system.

Stability analysis on natural circulation boiling water reactors

Energy Technology Data Exchange (ETDEWEB)

Metz, Peter

1999-05-01

The purpose of the study is a stability analysis of the simplified boiling water reactor concept. A fluid dynamics code, DYNOS, was developed and successfully validated against FRIGG and DESIRE data and a stability benchmark on the Ringhals 1 forced circulation BWR. Three simplified desings were considered in the analysis: The SWRIOOO by Siemens and the SBWR and ESBWR from the General Electric Co. For all three design operational characteristics, i.e. power versus flow rate maps, were calculated. The effects which different geometric and operational parameters, such as the riser height, inlet subcooling etc., have on the characteristics have been investigated. Dynamic simulations on the three simplified design revealed the geysering and the natural circulation oscillations modes only. They were, however, only encountered at pressure below 0.6 MPa. Stability maps for all tree simplified BWRs were calculated and plotted. The study concluded that a fast pressurisation of the reactor vessel is necessary to eliminate the possibility of geysering or natural circulation oscillations mode instability. (au) 26 tabs., 88 ills.

Development of TPNCIRC code for Evaluation of Two-Phase Natural Circulation Flow Performance under External Reactor Vessel Cooling Conditions

International Nuclear Information System (INIS)

Choi, A-Reum; Song, Hyuk-Jin; Park, Jong-Woon

2015-01-01

During a severe accident, corium is relocated to the lower head of the nuclear reactor pressure vessel (RPV). Design concept of retaining the corium inside a nuclear reactor pressure vessel (RPV) through external cooling under hypothetical core melting accidents is called external reactor vessel cooling (ERVC). In this respect, validated two-phase natural circulation flow (TPNC) model is necessary to determine the adequacy of the ERVC design and operating conditions such as inlet area, form losses, gap distance, riser length and coolant conditions. The most important model generally characterizing the TPNC are void fraction and two-phase friction factors. Typical experimental and analytical studies to be referred to on two-phase circulation flow characteristics are those by Reyes, Gartia et al. based on Vijayan et al., Nayak et al. and Dubey et al. In the present paper, two-phase natural circulation (TPNC) flow characteristics under external reactor vessel cooling (ERVC) conditions are studied using two existing TPNC flow models of Reyes and Gartia et al. incorporating more improved void fraction and two-phase friction models. These models and correlations are integrated into a computer program, TPNCIRC, which can handle candidate ERVC design parameters, such as inlet, riser and downcomer flow lengths and areas, gap size between reactor vessel and surrounding insulations, minor loss factors and operating parameters of decay power, pressure and subcooling. Accuracy of the TPNCIRC program is investigated with respect to the flow rate and void fractions for existing measured data from a general experiment and ULPU specifically designed for the AP1000 in-vessel retention. Also, the effect of some important design parameters are examined for the experimental and plant conditions. Using the flow models and correlations are integrated into a computer program, TPNCIRC, a number of correlations have been examined. This seems coming from the differences of void fractions

Effect of the fcc-hcp martensitic transition on the equation of state of solid krypton up to 140 GPa

Science.gov (United States)

Rosa, A. D.; Garbarino, G.; Briggs, R.; Svitlyk, V.; Morard, G.; Bouhifd, M. A.; Jacobs, J.; Irifune, T.; Mathon, O.; Pascarelli, S.

2018-03-01

Solid krypton (Kr) undergoes a pressure-induced martensitic phase transition from a face-centered cubic (fcc) to a hexagonal close-packed (hcp) structure. These two phases coexist in a very wide pressure domain inducing important modifications of the bulk properties of the resulting mixed phase system. Here, we report a detailed in situ x-ray diffraction and absorption study of the influence of the fcc-hcp phase transition on the compression behavior of solid krypton in an extended pressure domain up to 140 GPa. The onset of the hcp-fcc transformation was observed in this study at around 2.7 GPa and the coexistence of these two phases up to 140 GPa, the maximum investigated pressure. The appearance of the hcp phase is also evidenced by the pressure-induced broadening and splitting of the first peak in the XANES spectra. We demonstrate that the transition is driven by a continuous nucleation and intergrowth of nanometric hcp stacking faults that evolve in the fcc phase. These hcp stacking faults are unaffected by high-temperature annealing, suggesting that plastic deformation is not at their origin. The apparent small Gibbs free-energy differences between the two structures that decrease upon compression may explain the nucleation of hcp stacking faults and the large coexistence domain of fcc and hcp krypton. We observe a clear anomaly in the equation of state of the fcc solid at ˜20 GPa when the proportion of the hcp form reaches ˜20 % . We demonstrate that this anomaly is related to the difference in stiffness between the fcc and hcp phases and propose two distinct equation of states for the low and high-pressure regimes.

A Guide to Federal Regulation; Understanding the FCC Rules.

Science.gov (United States)

Cable Television Information Center, Washington, DC.

While it is apparent that the Federal Communications Commission (FCC) has given a great deal of thought to the regulation of cable systems, the basic success or failure of cable as a communications service will depend on local development. Relatively little guidance has been provided to local franchising authorities for selecting among applicants,…

High-Pressure Geophysical Properties of Fcc Phase FeHX

Science.gov (United States)

Thompson, E. C.; Davis, A. H.; Bi, W.; Zhao, J.; Alp, E. E.; Zhang, D.; Greenberg, E.; Prakapenka, V. B.; Campbell, A. J.

2018-01-01

Face centered cubic (fcc) FeHX was synthesized at pressures of 18-68 GPa and temperatures exceeding 1,500 K. Thermally quenched samples were evaluated using synchrotron X-ray diffraction (XRD) and nuclear resonant inelastic X-ray scattering (NRIXS) to determine sample composition and sound velocities to 82 GPa. To aid in the interpretation of nonideal (X ≠ 1) stoichiometries, two equations of state for fcc FeHX were developed, combining an empirical equation of state for iron with two distinct synthetic compression curves for interstitial hydrogen. Matching the density deficit of the Earth's core using these equations of state requires 0.8-1.1 wt % hydrogen at the core-mantle boundary and 0.2-0.3 wt % hydrogen at the interface of the inner and outer cores. Furthermore, a comparison of Preliminary Reference Earth Model (PREM) to a Birch's law extrapolation of our experimental results suggests that an iron alloy containing ˜0.8-1.3 wt % hydrogen could reproduce both the density and compressional velocity (VP) of the Earth's outer core.

Towards an unbiased comparison of CC, BCC, and FCC lattices in terms of prealiasing

KAUST Repository

Vad, Viktor

2014-06-01

In the literature on optimal regular volume sampling, the Body-Centered Cubic (BCC) lattice has been proven to be optimal for sampling spherically band-limited signals above the Nyquist limit. On the other hand, if the sampling frequency is below the Nyquist limit, the Face-Centered Cubic (FCC) lattice was demonstrated to be optimal in reducing the prealiasing effect. In this paper, we confirm that the FCC lattice is indeed optimal in this sense in a certain interval of the sampling frequency. By theoretically estimating the prealiasing error in a realistic range of the sampling frequency, we show that in other frequency intervals, the BCC lattice and even the traditional Cartesian Cubic (CC) lattice are expected to minimize the prealiasing. The BCC lattice is superior over the FCC lattice if the sampling frequency is not significantly below the Nyquist limit. Interestingly, if the original signal is drastically undersampled, the CC lattice is expected to provide the lowest prealiasing error. Additionally, we give a comprehensible clarification that the sampling efficiency of the FCC lattice is lower than that of the BCC lattice. Although this is a well-known fact, the exact percentage has been erroneously reported in the literature. Furthermore, for the sake of an unbiased comparison, we propose to rotate the Marschner-Lobb test signal such that an undue advantage is not given to either lattice. © 2014 The Eurographics Association and John Wiley & Sons Ltd. Published by John Wiley & Sons Ltd.

Towards an unbiased comparison of CC, BCC, and FCC lattices in terms of prealiasing

KAUST Repository

Vad, Viktor; Csé bfalvi, Balá zs; Rautek, Peter; Grö ller, Eduard M.

2014-01-01

In the literature on optimal regular volume sampling, the Body-Centered Cubic (BCC) lattice has been proven to be optimal for sampling spherically band-limited signals above the Nyquist limit. On the other hand, if the sampling frequency is below the Nyquist limit, the Face-Centered Cubic (FCC) lattice was demonstrated to be optimal in reducing the prealiasing effect. In this paper, we confirm that the FCC lattice is indeed optimal in this sense in a certain interval of the sampling frequency. By theoretically estimating the prealiasing error in a realistic range of the sampling frequency, we show that in other frequency intervals, the BCC lattice and even the traditional Cartesian Cubic (CC) lattice are expected to minimize the prealiasing. The BCC lattice is superior over the FCC lattice if the sampling frequency is not significantly below the Nyquist limit. Interestingly, if the original signal is drastically undersampled, the CC lattice is expected to provide the lowest prealiasing error. Additionally, we give a comprehensible clarification that the sampling efficiency of the FCC lattice is lower than that of the BCC lattice. Although this is a well-known fact, the exact percentage has been erroneously reported in the literature. Furthermore, for the sake of an unbiased comparison, we propose to rotate the Marschner-Lobb test signal such that an undue advantage is not given to either lattice. © 2014 The Eurographics Association and John Wiley & Sons Ltd. Published by John Wiley & Sons Ltd.

On the nature of the dhcp to fcc transition under pressure in Pr and Pr-Th alloys

International Nuclear Information System (INIS)

Vijayakumar, V.; Godwal, B.K.; Sikka, S.K.; Chidambaram, R.

1988-01-01

The results of electrical resistance (R), thermoelectric power (TEP) and X-ray diffraction measurements on praseodymium (Pr) and its alloys with thorium under pressure are reported. The maximum in R vs P curve exhibited by Pr persists only in the dhcp phase of Pr-Th alloy. X-ray measurements confirmed that in the alloys also the maximum in R vs P curve is due to the dhcp → fcc transition. Thus the behaviour of Pr and Pr-Th alloys is different from that of La and its alloys with Ce and Th where the maximum in the R vs P curve is electronic in origin and is exhibited by the dhcp, fcc and dist fcc phases. (author). 14 refs

Iron Contamination Mechanism and Reaction Performance Research on FCC Catalyst

Directory of Open Access Journals (Sweden)

Zhaoyong Liu

2015-01-01

Full Text Available FCC (Fluid Catalytic Cracking catalyst iron poisoning would not only influence units’ product slate; when the poisoning is serious, it could also jeopardize FCC catalysts’ fluidization in reaction-regeneration system and further cause bad influences on units’ stable operation. Under catalytic cracking reaction conditions, large amount of iron nanonodules is formed on the seriously iron contaminated catalyst due to exothermic reaction. These nodules intensify the attrition between catalyst particles and generate plenty of fines which severely influence units’ smooth running. A dense layer could be formed on the catalysts’ surface after iron contamination and the dense layer stops reactants to diffuse to inner structures of catalyst. This causes extremely negative effects on catalyst’s heavy oil conversion ability and could greatly cut down gasoline yield while increasing yields of dry gas, coke, and slurry largely. Research shows that catalyst’s reaction performance would be severely deteriorated when iron content in E-cat (equilibrium catalyst exceeds 8000 μg/g.

Diagnosis of Catalyst Cooler and Riser in RFCC using Sealed gamma-ray Source

International Nuclear Information System (INIS)

Kim, Jin Seop; Kim, Jong Bum; Jung, Sung Hee; Kim, Jae Ho

2005-12-01

With a quantitative growth of the petroleum industry, a lot of budget are spent for the maintenance and repairs of facilities related to the process annually. Among them, the RFCC(residual fluid catalytic cracking) is a highly value-added unit which converts gas oil and heavier streams to lighter, more valuable products such as propylene, gasoline by an injection of atmospheric residue into the fluided catalyst. In this study, field experiments were performed to analyze the reasons of an abnormal operation in the catalyst cooler and the catalyst riser belonged to the RFCC unit respectively and to estimate the amount of seriousness using sealed gamma-ray source( 60 Co). The catalyst cooler functions cooling for the regeneration of a catalyst, which will be used to a new media in the RFCC unit. The catalyst riser, while, plays an important part in transporting to next cyclotron steps by mixing of an oil, steam and a catalyst mechanically. The purposes of this study is what was the condition of catalyst flow pattern and whether the coke was produced in an inside process or not. Gamma radiation counts were measured by the detector(NaI) positioned outside the pipe-wall diametrically opposite to the gamma source with a regular space. From the results, the section different from the distribution pattern of nearby catalyst in a facility was found. And this became the definitive information to a process operator. Diagnosis technique using gamma radiation source is proved to be the effective and reliable method in providing information on the media distribution in a facility

Design and performance studies of a hadronic calorimeter for a FCC-hh experiment

Science.gov (United States)

Faltova, J.

2018-03-01

The hadron-hadron Future Circular Collider (FCC-hh) project studies the physics reach of a proton-proton machine with a centre-of-mass-energy of 100 TeV and five times greater peak luminosities than at the High-Luminosity LHC (HL-LHC). The high-energy regime of the FCC-hh opens new opportunities for the discovery of physics beyond the standard model. At 100 TeV a large fraction of the W, Z, H bosons and top quarks are produced with a significant boost. It implies an efficient reconstruction of very high energetic objects decaying hadronically. The reconstruction of those boosted objects sets the calorimeter performance requirements in terms of energy resolution, containment of highly energetic hadron showers, and high transverse granularity. We present the current baseline technologies for the calorimeter system in the barrel region of the FCC-hh reference detector: a liquid argon electromagnetic and a scintillator-steel hadronic calorimeters. The focus of this paper is on the hadronic calorimeter and the performance studies for hadrons. The reconstruction of single particles and the achieved energy resolution for the combined system of the electromagnetic and hadronic calorimeters are discussed.

Influence of riser-induced slugs on the downstream separation processes

DEFF Research Database (Denmark)

Pedersen, Simon; Løhndorf, Petar Durdevic; Yang, Zhenyu

2017-01-01

In Oil & Gas installations the severe slug is an undesired flow regime due to the negative impact on the production rate and facility safety. This study will evaluate the severe riser-induced slugs’ influence to a typical separation process, consisting of a 3-phase gravity separator physically...... linked to a de-oiling hydrocyclone, based on experimental tests performed on a laboratory testing facility. Several scenarios are compared, while three PID controllers’ coefficients are kept constant for all the tests: The separator pressure, water level, and hydrocyclone pressure-drop-ratio (PDR......) controllers. Each respective scenario makes a comparison between uncontrolled, open-, and closed-loop anti-slug control configurations. It is concluded that both open- and closed-loop anti-slug control strategies improve the water level and PDR setpoint tracking equally well, but that the closed-loop strategy...

FCC046: A CANDIDATE GASEOUS POLAR RING DWARF ELLIPTICAL GALAXY IN THE FORNAX CLUSTER

Energy Technology Data Exchange (ETDEWEB)

De Rijcke, S.; Buyle, P.; Koleva, M. [Department of Physics and Astronomy, Ghent University, Krijgslaan 281 S9, B-9000 Ghent (Belgium)

2013-06-20

FCC046 is a Fornax Cluster dwarf elliptical galaxy. Optical observations have shown that this galaxy, besides an old and metal-poor stellar population, also contains a very young centrally concentrated population and is actively forming stars, albeit at a very low level. Here, we report on 21 cm observations of FCC046 with the Australia Telescope Compact Array which we conducted in the course of a small survey of Fornax Cluster early-type dwarf galaxies. We have discovered a {approx}10{sup 7} M{sub Sun} H I cloud surrounding FCC046. We show that the presence of this significant gas reservoir offers a concise explanation for this galaxy's optical morphological and kinematical properties. Surprisingly, the H I gas, as evidenced by its morphology and its rotational motion around the galaxy's optical major axis, is kinematically decoupled from the galaxy's stellar body. This is the first time such a ring of gaseous material in minor-axis rotation is discovered around a dwarf galaxy.

The influence of additions of Al and Si on the lattice stability of fcc and hcp Fe-Mn random alloys

Energy Technology Data Exchange (ETDEWEB)

Gebhardt, T; Music, D; Schneider, J M [Materials Chemistry, RWTH Aachen University, D-52056 Aachen (Germany); Ekholm, M; Abrikosov, I A [Department of Physics, Chemistry and Biology (IFM), Linkoeping University, SE-58183 Linkoeping (Sweden); Vitos, L [Department of Materials and Engineering, Applied Materials Physics, Royal Institute of Technology (KTH), SE-10044 Stockholm (Sweden); Dick, A; Hickel, T; Neugebauer, J, E-mail: gebhardt@mch.rwth-aachen.de [Department of Computational Materials Design, Max-Planck-Institut fuer Eisenforschung GmbH, D-40237 Duesseldorf (Germany)

2011-06-22

We have studied the influence of additions of Al and Si on the lattice stability of face-centred-cubic (fcc) versus hexagonal-closed-packed (hcp) Fe-Mn random alloys, considering the influence of magnetism below and above the fcc Neel temperature. Employing two different ab initio approaches with respect to basis sets and treatment of magnetic and chemical disorder, we are able to quantify the predictive power of the ab initio methods. We find that the addition of Al strongly stabilizes the fcc lattice independent of the regarded magnetic states. For Si a much stronger dependence on magnetism is observed. Compared to Al, almost no volume change is observed as Si is added to Fe-Mn, indicating that the electronic contributions are responsible for stabilization/destabilization of the fcc phase.

The influence of additions of Al and Si on the lattice stability of fcc and hcp Fe-Mn random alloys

International Nuclear Information System (INIS)

Gebhardt, T; Music, D; Schneider, J M; Ekholm, M; Abrikosov, I A; Vitos, L; Dick, A; Hickel, T; Neugebauer, J

2011-01-01

We have studied the influence of additions of Al and Si on the lattice stability of face-centred-cubic (fcc) versus hexagonal-closed-packed (hcp) Fe-Mn random alloys, considering the influence of magnetism below and above the fcc Neel temperature. Employing two different ab initio approaches with respect to basis sets and treatment of magnetic and chemical disorder, we are able to quantify the predictive power of the ab initio methods. We find that the addition of Al strongly stabilizes the fcc lattice independent of the regarded magnetic states. For Si a much stronger dependence on magnetism is observed. Compared to Al, almost no volume change is observed as Si is added to Fe-Mn, indicating that the electronic contributions are responsible for stabilization/destabilization of the fcc phase.

The Architecture and Beyond of Tread and Riser

Directory of Open Access Journals (Sweden)

Sai Sanath

2016-01-01

The primary constitution of stairs is the arrangement of horizontal and vertical measures known as tread and riser. This is the simplest arrangement that essentially conveys people from one level to the other with required comfort and safety. Steps are a universal symbol with multiple interpretations. They are the most generally used similes in art, philosophy and psychology. Stairs occupy a unique status in the built environment because they not only convey people, but also symbolize the psychological, spiritual and artistic aspects of human nature. The mental significance and symbolic connotations of steps are deeply rooted. Understanding the role of stairs in different spheres of human need and expression is crucial in approaching its design. The pattern of stairs is dependent on the type of materials and other related design considerations. It is one of the unique architectural entities that reflect the various facets of social, psychological, artistic, metaphysical and religious dimensions. The importance of physical activity in the rising sedentary life styles is linked to the design of building elements, especially the staircases. The advancement in technology has displaced the role of stairs into an inconsequential means of emergency escape. But the importance of physical activity in the rising sedentary lifestyle has revitalized the concept of stairs as an active building component. The mono functional approach to staircases in high-rise buildings, especially as the means of escape in emergency situations, indicates that the design of staircases as multi functional element is still under the confines of design explorations. This paper is an attempt to understand the concept of stairs not only from the evolutionary point of view, but also the associated metaphoric meanings and its emerging multi facet identity. The concept of vertical accessibility in the form of tread and riser arrangement makes stairs a timeless phenomenon. The approach to multi utility

Phonons in fcc binary alloys

International Nuclear Information System (INIS)

Sharma, Amita; Rathore, R.P.S.

1992-01-01

Born-Mayer potential has been modified to account for the unpaired (three body) forces among the common nearest neighbours of the ordered binary fcc alloys i.e. Ni 3 Fe 7 , Ni 5 Fe 5 and Ni 75 Fe 25 . The three body potential is added to the two body form of Morse to formalize the total interaction potential. Measured inverse ionic compressibility, cohesive energy, lattice constant and one measured phonon frequency are used to evaluate the defining parameters of the potential. The potential seeks to bring about the binding among 140 and 132 atoms though pair wise (two body) and non-pair wise (three body) forces respectively. The phonon-dispersion relations obtained by solving the secular equation are compared with the experimental findings on the aforesaid alloys. (author). 19 refs., 3 figs

Anti-Invar properties and magnetic order in fcc Fe-Ni-C alloy

International Nuclear Information System (INIS)

Nadutov, V.M.; Kosintsev, S.G.; Svystunov, Ye.O.; Garamus, V.M.; Willumeit, R.; Eckerlebe, H.; Ericsson, T.; Annersten, H.

2011-01-01

Anti-Invar effect was revealed in the fcc Fe-25.3%Ni-0.73%C (wt%) alloy, which demonstrates high values of thermal expansion coefficient (TEC) (15-21)x10 -6 K -1 accompanied by almost temperature-insensitive behavior in temperature range of 122-525 K. Alloying with carbon considerably expanded the low temperature range of anti-Invar behavior in fcc Fe-Ni-based alloy. The Curie temperature of the alloy T C =195 K was determined on measurements of temperature dependences of magnetic susceptibility and saturation magnetization. The Moessbauer and small-angle neutron scattering (SANS) experiments on the fcc Fe-25.3%Ni-(0.73-0.78)%C alloys with the varying temperatures below and above the Curie point and in external magnetic field of 1.5-5 T were conducted. Low value of the Debye temperature Θ D =180 K was estimated using the temperature dependence of the integral intensity of Moessbauer spectra for specified temperature range. The inequality B eff =(0.7-0.9)B ext was obtained in external field Moessbauer measurement that points to antiferromagnetically coupled Fe atoms, which have a tendency to align their spins perpendicular to B ext . Nano length scale magnetic inhomogeneities nearby and far above T C were revealed, which assumed that it is caused by mixed antiferromagnetically and ferromagnetically coupled Fe atom spins. The anti-Invar behavior of Fe-Ni-C alloy is explained in terms of evolution of magnetic order with changing temperature resulting from thermally varied interspin interaction and decreasing stiffness of interatomic bond. - Highlights: → Anti-Invar effect was revealed in the fcc Fe-25.3%Ni-0.73%C (wt%) alloy. → Carbon expanded the temperature range of anti-Invar behavior in Fe-Ni-based alloy. → Moessbauer data point to mixed interspin interaction and low the Dedye temperature. → The SANS experiments reveal nano length scale magnetic inhomogeneities ≤6 nm. → Anti-Invar behavior of Fe-Ni-C alloy explained by thermally varied magnetic order.

Two-Layer 16 Tesla Cosθ Dipole Design for the FCC

Energy Technology Data Exchange (ETDEWEB)

Holik, Eddie Frank [Fermilab; Ambrosio, Giorgio [Fermilab; Apollinari, G. [Fermilab

2018-02-13

The Future Circular Collider or FCC is a study aimed at exploring the possibility to reach 100 TeV total collision energy which would require 16 tesla dipoles. Upon the conclusion of the High Luminosity Upgrade, the US LHC Accelerator Upgrade Pro-ject in collaboration with CERN will have extensive Nb3Sn magnet fabrication experience. This experience includes robust Nb3Sn conductor and insulation scheming, 2-layer cos2θ coil fabrication, and bladder-and-key structure and assembly. By making im-provements and modification to existing technology the feasibility of a two-layer 16 tesla dipole is investigated. Preliminary designs indicate that fields up to 16.6 tesla are feasible with conductor grading while satisfying the HE-LHC and FCC specifications. Key challenges include accommodating high-aspect ratio conductor, narrow wedge design, Nb3Sn conductor grading, and especially quench protection of a 16 tesla device.

IODP Expedition 319, NanTroSEIZE Stage 2: First IODP Riser Drilling Operations and Observatory Installation Towards Understanding Subduction Zone Seismogenesis

Directory of Open Access Journals (Sweden)

Sean Toczko

2010-09-01

Full Text Available The Nankai Trough Seismogenic Zone Experiment (NanTroSEIZE is a major drilling project designed to investigate fault mechanics and the seismogenic behavior of subduction zone plate boundaries. Expedition 319 is the first riser drilling operation within scientific ocean drilling. Operations included riser drilling at Site C0009 in the forearc basin above the plate boundary fault, non-riser drilling at Site C0010 across the shallow part of the megasplay faultsystem—which may slip during plate boundary earthquakes—and initial drilling at Site C0011 (incoming oceanic plate for Expedition 322. At Site C0009, new methods were tested, including analysis of drill mud cuttings and gas, and in situ measurements of stress, pore pressure, and permeability. These results, in conjunction with earlier drilling, will provide a the history of forearc basin development (including links to growth of the megasplay fault system and modern prism, b the first in situ hydrological measurements of the plate boundary hanging wall, and c integration of in situ stress measurements (orientation and magnitude across the forearc and with depth. A vertical seismic profile (VSP experiment provides improved constraints on the deeper structure of the subduction zone. At Site C0010, logging-while-drilling measurements indicate significantchanges in fault zone and hanging wall properties over short (<5 km along-strike distances, suggesting different burial and/or uplift history. The first borehole observatory instruments were installed at Site C0010 to monitor pressure and temperature within the megasplay fault zone, and methods of deployment of more complex observatoryinstruments were tested for future operations.

Dislocation cross-slip in fcc solid solution alloys

International Nuclear Information System (INIS)

Nöhring, Wolfram Georg; Curtin, W.A.

2017-01-01

Cross-slip is a fundamental process of screw dislocation motion and plays an important role in the evolution of work hardening and dislocation structuring in metals. Cross-slip has been widely studied in pure FCC metals but rarely in FCC solid solutions. Here, the cross-slip transition path in solid solutions is calculated using atomistic methods for three representative systems of Ni-Al, Cu-Ni and Al-Mg over a range of solute concentrations. Studies using both true random alloys and their corresponding average-alloy counterparts allow for the independent assessment of the roles of (i) fluctuations in the spatial solute distribution in the true random alloy randomness and (ii) average alloy properties such as stacking fault energy. The results show that the solute fluctuations dominate the activation energy barrier, i.e. there are large sample-to-sample variations around the average activation barrier. The variations in activation barrier correlate linearly with the energy difference between the initial and final states. The distribution of this energy difference can be computed analytically in terms of the solute/dislocation interaction energies. Thus, the distribution of cross-slip activation energies can be accurately determined from a parameter-free analytic model. The implications of the statistical distribution of activation energies on the rate of cross-slip in real alloys are then identified.

A combined wear-fatigue design methodology for fretting in the pressure armour layer of flexible marine risers

OpenAIRE

O'Halloran, S.M.; Shipway, P.H.; Connaire, A.D.; Leen, Sean B.; Harte, A.M.

2017-01-01

This paper presents a combined experimental and computational methodology for fretting wear-fatigue prediction of pressure armour wire in flexible marine risers. Fretting wear, friction and fatigue parameters of pressure armour material have been characterised experimentally. A combined fretting wear-fatigue finite element model has been developed using an adaptive meshing technique and the effect of bending-induced tangential slip has been characterised. It has been shown that a surface dama...

Construction Method Study For Installation Of A Large Riser In A Single-Shell Tank

International Nuclear Information System (INIS)

Adkisson, D.A.

2010-01-01

This study evaluates and identifies a construction method for cutting a hole in a single-shell tank dome. This study also identifies and evaluates vendors for performing the cut. Single-shell tanks (SST) in the 241-C tank farm are currently being retrieved using various retrieval technologies (e.g., modified sluicing). The Hanford Federal Facility Agreement and Consent Order require that the SSTs be retrieved to less than 360 cubic feet of radioactive waste. The current technologies identified and deployed for tank retrieval have not been able to retrieve waste in accordance with the Hanford Federal Facility Agreement and Consent Order. As such, alternative retrieval systems have been proposed and are currently under construction that will have the ability to retrieve waste to this defined level. The proposed retrieval systems will not fit down existing risers. New risers will need to be installed to provide the retrieval systems access to the inside of the SSTs. The purpose of this study is two-fold. The first objective is to identify multiple concrete cutting technologies and perform an initial pre-screening, evaluate the technologies identified for more in-depth analysis, and recommend a technology/methodology for cutting a hole in the tank dome. The identified/pre-screened methods will be evaluated based on the following criteria: (1) Maturity/complexity; (2) Waste generation; (3) Safety; (4) Cost; and (5) Schedule. Once the preferred method is identified to cut the hole in the tank dome, the second objective is to identify, evaluate, and recommend a vendor for the technology selected that will perform the cutting process.

Overview of design development of FCC-hh Experimental Interaction Regions

CERN Document Server

AUTHOR|(CDS)2082479; Abelleira, Jose; Cruz Alaniz, Emilia; Van Riesen-Haupt, Leon; Benedikt, Michael; Besana, Maria Ilaria; Buffat, Xavier; Burkhardt, Helmut; Cerutti, Francesco; Langner, Andy Sven; Martin, Roman; Riegler, Werner; Schulte, Daniel; Tomas Garcia, Rogelio; Appleby, Robert Barrie; Rafique, Haroon; Barranco Garcia, Javier; Pieloni, Tatiana; Boscolo, Manuela; Collamati, Francesco; Nevay, Laurence James; Hofer, Michael

2017-01-01

The experimental interaction region (EIR) is one of the key areas that define the performance of the Future Circular Collider. In this overview we will describe the status and the evolution of the design of EIR of FCC-hh, focusing on design of the optics, energy deposition in EIR elements, beam-beam effects and machine detector interface issues.

Future Circular Collider Study (FCC) kick-off meeting | 12-15 February

CERN Multimedia

2014-01-01

The kick-off meeting of the international "Future Circular Collider Study" (FCC) will take place in Geneva from 12 to 15 February 2014 at the University of Geneva, Unimail site. The programme and registration details can be found on the meeting's website. This meeting is the starting point of the five-year international "Future Circular Collider Study" (FCC). The main emphasis of the conceptual design study will be on a hadron collider with a centre-of-mass energy of the order of 100 TeV in a new tunnel with a 80-100 km circumference for the purposes of studying physics at the highest energies. The study will also include a lepton collider, as a potential intermediate step towards realisation of the hadron facility. Options for e-p scenarios will also be considered. The main purpose of this meeting is to discuss the study topics and to prepare international collaborations. The meeting is a public meeting with a registration deadline closing on Friday 31 Janua...

Description of hardening curves of fcc single- and polycrystals

International Nuclear Information System (INIS)

Mecking, H.

1975-01-01

Stress-strain curves are analyzed over their entire strain region and over a wide range of temperatures to arrive at a general analytic description of work-hardening curves. The data were obtained with fcc single and polycrystals, but there is experimental and theoretical evidence that the principles of the analysis are also applicable for other crystal structures and even for more complex technical materials. 9 figs, 1 table, 46 refs

Crystal phase-based epitaxial growth of hybrid noble metal nanostructures on 4H/fcc Au nanowires

Science.gov (United States)

Lu, Qipeng; Wang, An-Liang; Gong, Yue; Hao, Wei; Cheng, Hongfei; Chen, Junze; Li, Bing; Yang, Nailiang; Niu, Wenxin; Wang, Jie; Yu, Yifu; Zhang, Xiao; Chen, Ye; Fan, Zhanxi; Wu, Xue-Jun; Chen, Jinping; Luo, Jun; Li, Shuzhou; Gu, Lin; Zhang, Hua

2018-03-01

Crystal-phase engineering offers opportunities for the rational design and synthesis of noble metal nanomaterials with unusual crystal phases that normally do not exist in bulk materials. However, it remains a challenge to use these materials as seeds to construct heterometallic nanostructures with desired crystal phases and morphologies for promising applications such as catalysis. Here, we report a strategy for the synthesis of binary and ternary hybrid noble metal nanostructures. Our synthesized crystal-phase heterostructured 4H/fcc Au nanowires enable the epitaxial growth of Ru nanorods on the 4H phase and fcc-twin boundary in Au nanowires, resulting in hybrid Au-Ru nanowires. Moreover, the method can be extended to the epitaxial growth of Rh, Ru-Rh and Ru-Pt nanorods on the 4H/fcc Au nanowires to form unique hybrid nanowires. Importantly, the Au-Ru hybrid nanowires with tunable compositions exhibit excellent electrocatalytic performance towards the hydrogen evolution reaction in alkaline media.

Realizing high magnetic moments in fcc Fe nanoparticles through atomic structure stretch

International Nuclear Information System (INIS)

Baker, S H; Roy, M; Thornton, S C; Binns, C

2012-01-01

We describe the realization of a high moment state in fcc Fe nanoparticles through a controlled change in their atomic structure. Embedding Fe nanoparticles in a Cu 1-x Au x matrix causes their atomic structure to switch from bcc to fcc. Extended x-ray absorption fine structure (EXAFS) measurements show that the structure in both the matrix and the Fe nanoparticles expands as the amount of Au in the matrix is increased, with the data indicating a tetragonal stretch in the Fe nanoparticles. The samples were prepared directly from the gas phase by co-deposition, using a gas aggregation source and MBE-type sources respectively for the nanoparticle and matrix materials. The structure change in the Fe nanoparticles is accompanied by a sharp increase in atomic magnetic moment, ultimately to values of ∼2.5 ± 0.3 μ B /atom. (paper)

Low-cycle fatigue-cracking mechanisms in fcc crystalline materials

Science.gov (United States)

Zhang, P.; Qu, S.; Duan, Q. Q.; Wu, S. D.; Li, S. X.; Wang, Z. G.; Zhang, Z. F.

2011-01-01

The low-cycle fatigue (LCF) cracking behavior in various face-centered-cubic (fcc) crystalline materials, including Cu single crystals, bicrystals and polycrystals, Cu-Al and Cu-Zn alloys, ultrafine-grained (UFG) Al-Cu and Cu-Zn alloys, was systematically investigated and reviewed. In Cu single crystals, fatigue cracking always nucleates along slip bands and deformation bands. The large-angle grain boundary (GB) becomes the preferential site in bicrystals and polycrystals. In addition, fatigue cracking can also nucleate along slip bands and twin boundaries (TBs) in polycrystalline materials. However, shear bands and coarse deformation bands are observed to the preferential sites for fatigue cracking in UFG materials with a large number of GBs. Based on numerous observations on fatigue-cracking behavior, the fatigue-cracking mechanisms along slip bands, GBs, TBs, shear bands and deformation bands were systematically compared and classified into two types, i.e. shear crack and impingement crack. Finally, these fatigue-cracking behaviors are discussed in depth for a better understanding of their physical nature and the transition from intergranular to transgranular cracking in various fcc crystalline materials. These comprehensive results for fatigue damage mechanisms should significantly aid in obtaining the optimum design to further strengthen and toughen metallic materials in practice.

Study of the physics potential of the FCC-hh machine to measure the coupling of the Higgs boson to b quarks

CERN Document Server

Rodríguez, Arturo

2016-01-01

The FCC project as well as the Pythia + Delphes analysis within the FCC software are introduced. The ROOT analysis carried out to reconstruct main observables, such the invariant mass of the bb system, transverse mass and momentum of the W boson together with the lepton pT and distribution is explained. The resulting reconstructed invariant mass of the bb system showed a peak near the 125 GeV in correspondence with the Higgs boson. Future steps towards estimating the physics potential of the FCC-hh machine in this channel are discussed.

47 CFR 0.409 - Commission policy on private printing of FCC forms.

Science.gov (United States)

2010-10-01

... ORGANIZATION General Information General § 0.409 Commission policy on private printing of FCC forms. The... in quality to the original document, without change to the page size, image size, configuration of... Managing Director. [53 FR 27861, July 25, 1988] Printed Publications ...

Quasi-static crack tip fields in rate-sensitive FCC single crystals

Indian Academy of Sciences (India)

In this work, the effects of loading rate, material rate sensitivity and constraint level on quasi-static crack tip fields in a FCC single crystal are studied. ... Global General Motors R&D, India Science Lab, GM Technical Centre (India), Bangalore 560 066, India; Department of Mechanical Engineering, Indian Institute of Science, ...

Synthesis and characterization of branched fcc/hcp ruthenium nanostructures and their catalytic activity in ammonia borane hydrolysis

KAUST Repository

AlYami, Noktan

2018-01-30

Several systems have shown the ability to stabilize uncommon crystal structures during the synthesis of metallic nanoparticles. By tailoring the nanoparticle crystal structure, the physical and chemical properties of the particles can also be controlled. Herein, we first synthesized branched nanoparticles of mixed hcp/fcc ruthenium, which were formed using tungsten carbonyl [W(CO)6] as both a reducing agent and a source of carbon monoxide. The branched particles were formed from multiple particulates off a central core. High-resolution transmission electron microscopy (HRTEM) clearly showed that the branched structures consisted of aligned hcp crystal domains, a mixture of fcc and hcp crystal domains with several defects and misalignments, and particles that contained multiple cores and branches. Branched particles were also formed with molybdenum carbonyl [Mo(CO)6], and faceted particles of hcp and fcc particles were formed with Re2(CO)10 as a carbon monoxide source. Without metal carbonyls, small particles of spherical hcp ruthenium were produced, and their size could be controlled by the selection of the precursor. The ruthenium nanoparticles were tested for ammonia borane hydrolysis; the branched nanoparticles were more reactive for catalytic hydrogen evolution than the faceted hcp/fcc nanoparticles or the spherical hcp nanoparticles. This work showcases the potential of crystal phase engineering of transition metal nanoparticles by different carbon monoxide precursors for tailoring their catalytic reactivity.

Microstructural analysis and the mechanism if the coke formation in a refractory castable used in a fluidized catalytic cracking unit; Analise microestructural e mecanismo de formacao do coque em um concreto refratario utilizado em unidades de craqueamento catalitico fludizado

Energy Technology Data Exchange (ETDEWEB)

Cabrelon, M.D.; Rodrigues, J.A. [Universidade Federal de Sao Carlos (GEMM/UFSCAR), Sao Carlos, SP (Brazil). Grupo de Engenharia de Microestrutura de Materiais], Email: marcelodezena@gmail.com; Medeiros, J. [PETROBRAS, Rio de Janeiro, RJ (Brazil). Centro de Pesquisas; Toledo Filho, R.D. [Coordenacao dos Programas de Pos-Graduacao de Engenharia (COPPE/UFRJ), Rio de Janeiro, RJ (Brazil). Lab. de Estruturas e Materiais

2010-07-01

The cokes formation in the refractory castables for FCC's unit is cited as one the most relevant problem in the internal face of the petrochemical Riser, but its mechanism is still unknown. In this sense, was made a microstructural study with a anti-erosive refractory castable class C, exposed to a cokemaker atmosphere, aiming to identify a mechanism to explain the coke's formation. For this reason, test samples were molded and subjected to a cokemaker process in the reactor pilot from CENPES-PETROBRAS-RJ, under an atmosphere of propene, as one temperature of 540 deg C and soaking time ranging between 10 and 480h. These samples had their internal and surface microstructures analyzed by Optical and Scanning Electron Microscopy. The results showed that the aggregates had deterioration and your internal pores were filled with coke. In this point, starts the growth of microspheres of coke on the external face, coalescing and forming 'columns' in which become denser when increasing the exposure time to a saturated atmosphere with hydrocarbon. (author)

Microstructural analysis and the mechanism if the coke formation in a refractory castable used in a fluidized catalytic cracking unit; Analise microestructural e mecanismo de formacao do coque em um concreto refratario utilizado em unidades de craqueamento catalitico fludizado

Energy Technology Data Exchange (ETDEWEB)

Cabrelon, M D; Rodrigues, J.A. [Universidade Federal de Sao Carlos (GEMM/UFSCAR), Sao Carlos, SP (Brazil). Grupo de Engenharia de Microestrutura de Materiais], Email: marcelodezena@gmail.com; Medeiros, J [PETROBRAS, Rio de Janeiro, RJ (Brazil). Centro de Pesquisas; Toledo Filho, R D [Coordenacao dos Programas de Pos-Graduacao de Engenharia (COPPE/UFRJ), Rio de Janeiro, RJ (Brazil). Lab. de Estruturas e Materiais

2010-07-01

The cokes formation in the refractory castables for FCC's unit is cited as one the most relevant problem in the internal face of the petrochemical Riser, but its mechanism is still unknown. In this sense, was made a microstructural study with a anti-erosive refractory castable class C, exposed to a cokemaker atmosphere, aiming to identify a mechanism to explain the coke's formation. For this reason, test samples were molded and subjected to a cokemaker process in the reactor pilot from CENPES-PETROBRAS-RJ, under an atmosphere of propene, as one temperature of 540 deg C and soaking time ranging between 10 and 480h. These samples had their internal and surface microstructures analyzed by Optical and Scanning Electron Microscopy. The results showed that the aggregates had deterioration and your internal pores were filled with coke. In this point, starts the growth of microspheres of coke on the external face, coalescing and forming 'columns' in which become denser when increasing the exposure time to a saturated atmosphere with hydrocarbon. (author)

The Effect of Stick Stiffness of Friction Models on the Bending Behavior in Non-Bonded Flexible Risers

OpenAIRE

Dai, Tianjiao; Ye, Naiquan; Sævik, Svein

2017-01-01

This paper investigates the effect of stick stiffness on the bending behavior in non-bonded flexible risers. The stick stiffness was normally implemented in the friction model for calculating the friction stress between layers in such structures. As the stick stiffness may be too small to achieve the plane-surfaces-remain-plane assumption under low contact pressure in some friction models [1], a new friction model was proposed for maintaining the constant stick stiffness in the present work. ...

Steel catenary riser design based on coupled analysis methodology; Projeto de um riser rigido em catenaria baseado em metodologia de analise acoplada

Energy Technology Data Exchange (ETDEWEB)

Bahiense, Rodrigo A.; Rodrigues, Marcos V. [Det Norske Veritas (DNV), Rio de Janeiro, RJ (Brazil)

2008-07-01

Due to adoption of oil and gas production systems to deep and ultra-deep water, achieving frontiers that were not conceivable before, research in computational methods has contributed to implementation of sophisticated and efficient numerical tools in order to perform simulations considering those operational conditions. Thus, this work presents a steel catenary riser (SCR) design which is connected to a semi-submersible platform where the applied motions to SCR are obtained from analyses based on de-coupled and coupled methodologies. With increase of the line number of the system and water depth, the effects due to coupling of the lines on the platform motions are significant. It can be observed from performed evaluations for a floating production system, comparing the obtained results for SCR under extreme and fatigue conditions when it was submitted to the platform motions considering both methodologies mentioned. So, from the results obtained it can be concluded that for production system evaluated the adoption of decoupled methodology presents more conservative results. Thus the adoption of the coupled model associated to design practice of production lines presents as an alternative more realist and accurate to provide the optimization in the design of these structures. (author)

Physics Perspectives for a Future Circular Collider: FCC-ee

CERN Multimedia

CERN. Geneva

2017-01-01

The lectures will briefly discuss the parameters of a Future Circular Collider, before addressing in detail the physics perspectives and the challenges for the experiments and detector systems. The main focus will be on ee and pp collisions, but opportunities for e—p physics will also be covered. The FCC physics perspectives will be presented with reference to the ongoing LHC programme, including the physics potential from future upgrades to the LHC in luminosity and possibly energy.  

First results for a FCC-hh ring optics design

CERN Document Server

Chance, Antoine; Payet, Jacques; Alemany Fernandez, Reyes; Holzer, Bernhard; Schulte, Daniel

2015-01-01

The first order considerations of the optics for the FCC-hh ring are presented. The arc cell is generated taking into account some general considerations like the whole circumference, maximum gradients and lengths of the elements in the cell. The integration of the insertion regions started. Three types of Dispersion Suppressors (DIS) are studied. The sensitivity of the arc parameters to these layout considerations is studied in more detail. An alternative layout is shown as well.

Proceedings, High-Precision $\\alpha_s$ Measurements from LHC to FCC-ee

Energy Technology Data Exchange (ETDEWEB)

d' Enterria, David [CERN; Skands, Peter Z. [Monash U.

2015-01-01

This document provides a writeup of all contributions to the workshop on "High precision measurements of $\\alpha_s$: From LHC to FCC-ee" held at CERN, Oct. 12--13, 2015. The workshop explored in depth the latest developments on the determination of the QCD coupling $\\alpha_s$ from 15 methods where high precision measurements are (or will be) available. Those include low-energy observables: (i) lattice QCD, (ii) pion decay factor, (iii) quarkonia and (iv) $\\tau$ decays, (v) soft parton-to-hadron fragmentation functions, as well as high-energy observables: (vi) global fits of parton distribution functions, (vii) hard parton-to-hadron fragmentation functions, (viii) jets in $e^\\pm$p DIS and $\\gamma$-p photoproduction, (ix) photon structure function in $\\gamma$-$\\gamma$, (x) event shapes and (xi) jet cross sections in $e^+e^-$ collisions, (xii) W boson and (xiii) Z boson decays, and (xiv) jets and (xv) top-quark cross sections in proton-(anti)proton collisions. The current status of the theoretical and experimental uncertainties associated to each extraction method, the improvements expected from LHC data in the coming years, and future perspectives achievable in $e^+e^-$ collisions at the Future Circular Collider (FCC-ee) with $\\cal{O}$(1--100 ab$^{-1}$) integrated luminosities yielding 10$^{12}$ Z bosons and jets, and 10$^{8}$ W bosons and $\\tau$ leptons, are thoroughly reviewed. The current uncertainty of the (preliminary) 2015 strong coupling world-average value, $\\alpha_s(m_Z)$ = 0.1177 $\\pm$ 0.0013, is about 1\\%. Some participants believed this may be reduced by a factor of three in the near future by including novel high-precision observables, although this opinion was not universally shared. At the FCC-ee facility, a factor of ten reduction in the $\\alpha_s$ uncertainty should be possible, mostly thanks to the huge Z and W data samples available.

Resistencia a la corrosión ácida de morteros de cementos adicionados con catalizador de craqueo catalítico gastado (sFCC

Directory of Open Access Journals (Sweden)

Silvia Izquierdo

Full Text Available El catalizador de craqueo catalítico gastado (sFCC es un residuo producido por la industria petroquímica y ha demostrado una elevada potencialidad como adición puzolánica en mezclas de cemento Portland (OPC. El presente artículo evalúa la eficacia del sFCC como adición mineral activa en morteros de cemento Portland, así como la resistencia al ataque químico cuando los materiales producidos son inmersos en ácido sulfúrico (H2SO4, acético (CH3COOH o clorhídrico (HCl. Se llevó a cabo una comparación del desempeño del sFCC como adición frente a adiciones comercialmente disponibles, tales como humo de sílice (SF y metacaolín (MK. Los resultados revelan un incremento en las resistencias mecánicas de hasta un 17% en morteros con sFCC en comparación a un mortero referencia sin adición (OPC. La inmersión en H2SO4 durante 90 días condujo a la formación de yeso y pérdida de resistencias mecánicas de hasta un ~25% en las mezclas con MK y sFCC. Para las muestras inmersas en HCl y especialmente las constituidas con sFCC y MK, se identificó Sal de Friedel, como consecuencia del ingreso de Cl" y posterior reacción con los monosulfoaluminatos formados durante la hidratación del cemento. La inmersión en ácido acético condujo a pérdidas de resistencia de hasta un 57% para OPC y 37% para morteros adicionados con sFCC. De esta manera, la inmersión en HCl promueve el mayor ataque para los sistemas adicionados y posterior deterioro, seguido del CH3COOH y H2SO4. Se destaca el mejor desempeño del mortero con 20% sFCC, en particular en presencia de ácido sulfúrico.

COMPUTATIONAL AND EXPERIMENTAL MODELING OF THREE-PHASE SLURRY-BUBBLE COLUMN REACTOR

Energy Technology Data Exchange (ETDEWEB)

Isaac K. Gamwo; Dimitri Gidaspow

1999-09-01

Considerable progress has been achieved in understanding three-phase reactors from the point of view of kinetic theory. In a paper in press for publication in Chemical Engineering Science (Wu and Gidaspow, 1999) we have obtained a complete numerical solution of bubble column reactors. In view of the complexity of the simulation a better understanding of the processes using simplified analytical solutions is required. Such analytical solutions are presented in the attached paper, Large Scale Oscillations or Gravity Waves in Risers and Bubbling Beds. This paper presents analytical solutions for bubbling frequencies and standing wave flow patterns. The flow patterns in operating slurry bubble column reactors are not optimum. They involve upflow in the center and downflow at the walls. It may be possible to control flow patterns by proper redistribution of heat exchangers in slurry bubble column reactors. We also believe that the catalyst size in operating slurry bubble column reactors is not optimum. To obtain an optimum size we are following up on the observation of George Cody of Exxon who reported a maximum granular temperature (random particle kinetic energy) for a particle size of 90 microns. The attached paper, Turbulence of Particles in a CFB and Slurry Bubble Columns Using Kinetic Theory, supports George Cody's observations. However, our explanation for the existence of the maximum in granular temperature differs from that proposed by George Cody. Further computer simulations and experiments involving measurements of granular temperature are needed to obtain a sound theoretical explanation for the possible existence of an optimum catalyst size.

Atomic structure of radiation damages in FCC-metals after neutron irradiation

International Nuclear Information System (INIS)

Popova, E.V.; Ivchenko, V.A.; Kozlov, A.V.

2005-01-01

Full text: Radiation clusters, formed at a neutron irradiation, are a product of evolution of cascade areas. The quantitative information about clusters can be used for verification of calculations of cascade damage ability, in particular, cascade efficiency. Data about concentration clusters and an average of the vacancies containing in them, allow to receive total of the vacancies reserved in them and to use them for comparison to results of calculations of cascade damage ability. A correctness of such comparison by that above, than below temperature of a neutron irradiation. The purpose of work was experimental studying radiation clusters formed in FCC-metals at a low temperature neutron irradiation methods of dilatometry, field ion (FIM) and transmission electronic microscopy (TEM). Radiation clusters were studied: in industrial austenite steel C0.05Crl6Nil5Mo2Mnl, irradiated in reactor Rw-2a at temperature 310 K up to fluence intermediate and fast neutrons (with E > 0,1 MeV) 6.7·l0 21 m -2 ; in a modelling material - Pt (cleanliness of 99.99 %) with the same - FCC-structure in an initial condition and after an irradiation in reactor RWW-2M at temperature 310 K up to fluence intermediate and fast neutrons (with E > 0.1 MeV) 3.5·10 22 m -2 . As a result of an irradiation of steel and pure Pt, in these materials by methods FIM and TEM many radiation clusters, the accelerated neutrons initiated by interaction with substance was revealed. It is established that these damage areas represent the depleted zones containing separate vacancies, and also small vacancy complexes, with the 'belt' interstitial atoms. The quantitative estimation of the sizes of such radiating defects is lead and their density in volume is experimentally established. So the neutron irradiation of steel at temperature 310 K up to fluence 6.7·10 21 m -2 causes formation radiation clusters which average diameter according to TEM makes 3 nanometers. Observable by methods FIM clusters have the

Electronic Structure of the fcc Transition Metals Ir, Rh, Pt, and Pd

DEFF Research Database (Denmark)

Andersen, O. Krogh

1970-01-01

We give a complete description of a relativistic augmented-plane-wave calculation of the band structures of the paramagnetic fcc transition metals Ir, Rh, Pt, and Pd. The width and position of the d band decrease in the sequence Ir, Pt, Rh, Pd; and N(EF)=13.8,23.2,18.7, and 32.7 (states/atom)/Ry,......We give a complete description of a relativistic augmented-plane-wave calculation of the band structures of the paramagnetic fcc transition metals Ir, Rh, Pt, and Pd. The width and position of the d band decrease in the sequence Ir, Pt, Rh, Pd; and N(EF)=13.8,23.2,18.7, and 32.7 (states....../atom)/Ry, respectively. Spin-orbit coupling is important for all four metals and the coupling parameter varies by 30% over the d bandwidth. Detailed comparisons with de Haas—van Alphen Fermi-surface dimensions have previously been presented and the agreement was very good. Comparison with measured electronic specific...

Ultraboosted Zt and γt production at the HL-LHC and FCC-hh

Energy Technology Data Exchange (ETDEWEB)

Aguilar-Saavedra, J.A. [Universidad de Granada, Departamento de Fisica Teorica y del Cosmos, Granada (Spain)

2017-11-15

Searches for anomalous Zt and γt production provide an excellent probe of flavour-changing top interactions when the energies considered are very large. In this note we estimate the sensitivity to these interactions at the high-luminosity phase of the LHC and a future 100 TeV pp collider (FCC-hh). For the LHC, the expected limits on t → uZ/uγ branching ratios from Zt and γt production will reach the 10{sup -5} level, one order of magnitude better than the existing projections for t → uZ from t anti t production. For the FCC-hh, the limits on t → uZ/uγ could reach an impressive sensitivity at the 10{sup -6} level, with limits on t → cZ/cγ at the 10{sup -5} level. (orig.)

Roadside Infrastructure for Safer European Roads (RISER) D06: European Best Practice for Roadside Design: Guidelines for Roadside Infrastructure on New and Existing Roads

NARCIS (Netherlands)

Thomson, R.; Fagerlind, H.; Martinez, A.V.; Amenguel, A.; Naing, C.; Hill, J.; Hoschopf, H.; Dupré, G.; Bisson, O.; Kelkka, M.; Horst, A.R.A. van der; Garcia, J.

2006-01-01

The European Commission Directorate General for Transportation and Energy (DGTREN) sponsored a research project to investigate the best practice guidelines for roadside infrastructure. The RISER consortium has compiled the following document which is a synthesis of existing practice in Europe with

A study of fission product transport from failed fuel during N reactor postulated accidents

International Nuclear Information System (INIS)

Hagrman, D.L.

1989-09-01

This report presents a study of fission product transport behavior in N Reactor during a severe accident. More detail about fission product behavior than has previously been available is provided and key parameters that control this behavior are identified. The current report is an extension to a previous interum study that has added an aerosol formation model, replaced an older aerosol deposition model with an improved correlation, and incorporated results of a revised analysis of the process tubes. The LACE LA1 and LA3 tests are used to assess the revised model applied to determine aerosol deposition. The study concludes that a cesium iodide aerosol is likely to form near the downstream end of the process tubes. Transport of most of the released cesium and iodine as well as less volatile material depends on the behavior of this aerosol and the behavior is sensitive to several parameters that are not well known. If the environment is very clean and effluent flow is sufficient to support oxidation of the zircaloy and uranium of the process tubes, almost none of the aerosol deposits in the riser. Reduction of the effluent flow or the presence of high concentrations of aerosols of very low volatile material like zirconium, uranium, or their oxides causes deposition of the fission products in the riser piping. 24 refs., 18 figs., 11 tabs

A conceptual solution for a beam halo collimation system for the Future Circular hadron-hadron Collider (FCC-hh)

Science.gov (United States)

Fiascaris, M.; Bruce, R.; Redaelli, S.

2018-06-01

We present the first conceptual solution for a collimation system for the hadron-hadron option of the Future Circular Collider (FCC-hh). The collimation layout is based on the scaling of the present Large Hadron Collider collimation system to the FCC-hh energy and it includes betatron and momentum cleaning, as well as dump protection collimators and collimators in the experimental insertions for protection of the final focus triplet magnets. An aperture model for the FCC-hh is defined and the geometrical acceptance is calculated at injection and collision energy taking into account mechanical and optics imperfections. The performance of the system is then assessed through the analysis of normalized halo distributions and complete loss maps for an ideal lattice. The performance limitations are discussed and a solution to improve the system performance with the addition of dispersion suppression collimators around the betatron cleaning insertion is presented.

Cemento adicionado con un residuo del proceso de craqueo catalítico (FCC: hidratación y microestructura

Directory of Open Access Journals (Sweden)

Silvia Izquierdo

2013-08-01

Full Text Available El presente trabajo estudia el efecto de la incorporación de un residuo procedente de la industria petroquímica denominado catalizador gastado del craqueo catalítico (FCC en la hidratación y microestructura de pastas cementicias. Se utilizan como materiales de referencia, además del cemento portland (OPC, dos tipos de adición de alto desempeño, metacaolín (MK y humo de sílice (HS. La caracterización de los productos de hidratación se realizó por medio de difracción de rayos X (DRX, análisis termogravimétrico (TG, microscopia electrónica de barrido (SEM y resonancia magnética nuclear (NMR. Se complementa este estudio con la evaluación de la resistencia mecánica a compresión de morteros a edad hasta de 90 días. Los resultados indican que los principales productos de hidratación en las pastas adicionadas con FCC son silicato cálcico hidratado (CSH, aluminatos cálcicos hidratados (CAH y silicoaluminatos cálcicos hidratados (CASH. Pastas con 10% de FCC reportan un consumo de cal del 61% a edad de 360 días de curado, valor muy superior al reportado por las adiciones de MK y HS en la misma proporción, esto indica una mayor reactividad del FCC, que incluso se manifiesta a edades tempranas. Cabe anotar que, considerando el factor de dilución, la incorporación de un 10% de FCC como reemplazo del cemento contribuye a la resistencia del material adicionado en órdenes de hasta un 30%. Esto es un indicativo del uso potencial de este residuo como material suplementario en mezclas cementicias.

Development of OCDMA system based on Flexible Cross Correlation (FCC) code with OFDM modulation

Science.gov (United States)

Aldhaibani, A. O.; Aljunid, S. A.; Anuar, M. S.; Arief, A. R.; Rashidi, C. B. M.

2015-03-01

The performance of the OCDMA systems is governed by numerous quantitative parameters such as the data rate, simultaneous number of users, the powers of transmitter and receiver, and the type of codes. This paper analyzes the performance of the OCDMA system using OFDM technique to enhance the channel data rate, to save power and increase the number of user of OSCDMA systems compared with previous hybrid subcarrier multiplexing/optical spectrum code division multiplexing (SCM/OSCDM) system. The average received signal to noise ratio (SNR) with the nonlinearity of subcarriers is derived. The theoretical results have been evaluated based on BER and number of users as well as amount of power saved. The proposed system gave better performance and save around -6 dBm of the power as well as increase the number of users twice compare to SCM/OCDMA system. In addition it is robust against interference and much more spectrally efficient than SCM/OCDMA system. The system was designed based on Flexible Cross Correlation (FCC) code which is easier construction, less complexity of encoder/decoder design and flexible in-phase cross-correlation for uncomplicated to implement using Fiber Bragg Gratings (FBGs) for the OCDMA systems for any number of users and weights. The OCDMA-FCC_OFDM improves the number of users (cardinality) 108% compare to SCM/ODCMA-FCC system.

Model validation using CFD-grade experimental database for NGNP Reactor Cavity Cooling Systems with water and air

Energy Technology Data Exchange (ETDEWEB)

Manera, Annalisa [Univ. of Michigan, Ann Arbor, MI (United States); Corradini, Michael [Univ. of Wisconsin, Madison, WI (United States); Petrov, Victor [Univ. of Michigan, Ann Arbor, MI (United States); Anderson, Mark [Univ. of Wisconsin, Madison, WI (United States); Tompkins, Casey [Univ. of Wisconsin, Madison, WI (United States); Nunez, Daniel [Univ. of Michigan, Ann Arbor, MI (United States)

2018-02-13

This project has been focused on the experimental and numerical investigations of the water-cooled and air-cooled Reactor Cavity Cooling System (RCCS) designs. At this aim, we have leveraged an existing experimental facility at the University of Wisconsin-Madison (UW), and we have designed and built a separate effect test facility at the University of Michigan. The experimental facility at UW has underwent several upgrades, including the installation of advanced instrumentation (i.e. wire-mesh sensors) built at the University of Michigan. These provides highresolution time-resolved measurements of the void-fraction distribution in the risers of the water-cooled RCCS facility. A phenomenological model has been developed to assess the water cooled RCCS system stability and determine the root cause behind the oscillatory behavior that occurs under normal two-phase operation. Testing under various perturbations to the water-cooled RCCS facility have resulted in changes in the stability of the integral system. In particular, the effects on stability of inlet orifices, water tank volume have and system pressure been investigated. MELCOR was used as a predictive tool when performing inlet orificing tests and was able to capture the Density Wave Oscillations (DWOs) that occurred upon reaching saturation in the risers. The experimental and numerical results have then been used to provide RCCS design recommendations. The experimental facility built at the University of Michigan was aimed at the investigation of mixing in the upper plenum of the air-cooled RCCS design. The facility has been equipped with state-of-theart high-resolution instrumentation to achieve so-called CFD grade experiments, that can be used for the validation of Computational Fluid Dynanmics (CFD) models, both RANS (Reynold-Averaged) and LES (Large Eddy Simulations). The effect of risers penetration in the upper plenum has been investigated as well.

A novel start-up procedure for natural-circulation boiling water reactors

International Nuclear Information System (INIS)

Annalisa Manera; Frank Schaefer

2005-01-01

Valves). In this case steam is generated due to flashing at high pressure. The simulation by means of TRACG shows that no flow oscillations occur during the transition from single- to two-phase operation. A similar start-up procedure is simulated by Cheng and coauthors [4] by means of the code RAMONA-4B. They find contradicting results compared to the one obtained by Cheung and Rao. However, RAMONA-4B cannot predict the occurrence of flashing at low pressures, since a single average system pressure is used by this code to calculate thermodynamic properties of water and steam in the system. Therefore, the results obtained by this code are meaningless with regard to the start-up of natural circulation two-phase systems. In the present work a novel start-up procedure will be illustrated which does not require any additional system and in which there is no necessity for an abrupt steam production at high pressure [5], as in the procedure of Cheung and Rao. In the procedure proposed in this work, the reactor vessel is pressurized by means of steam produced in the reactor vessel itself, but outside the core and riser section. In this way, the system can be pressurized while the reactor still operates in single-phase conditions, thus without occurrence of flashing-induced flow oscillations. At the same time, a smooth steam production and pressurization of the system is achieved. The feasibility of the intermediate state in which steam is produced in the reactor vessel while the circulation in core and riser sections remains single-phase has been already proved during an experimental campaign performed at the large-scale facility PANDA. The procedure is simulated by means of the ATHLET code, developed by GRS (Germany). This code has been successfully qualified against low-pressure flashing-induced instabilities within the framework of the EU project NACUSP. (authors)

Kaolin and commercial fcc catalysts in the cracking of loads of polypropylene under refinary conditions

Directory of Open Access Journals (Sweden)

A. M. Ribeiro

2013-12-01

Full Text Available The efficiency of Commercial FCC catalysts (low, medium and high activities was evaluated by the catalytic cracking process of combined feeds of polypropylene (PP and vaseline, using a microactivity test unit (M.A.T. for the production of fuel fractions (gasoline, diesel and residue. The PP/vaseline loads, at 2.0% and 4.0% wt, were processed under refinery conditions (load/catalyst ratio and temperature of process. For the PP/vaseline load (4.0% wt, the production of the gasoline fraction was favored by all catalysts, while the diesel fraction was favored by PP/vaseline load (2.0% wt, showing a preferential contact of the zeolite external surface with the end of the polymer chains for the occurrence of the catalytic cracking. All the loads produced a bigger quantity of the gaseous products in the presence of highly active commercial FCC catalyst. The improvement in the activity of the commercial FCC catalyst decreased the production of the liquid fractions and increased the quantity of the solid fractions, independent of the concentration of the loads. These results can be related to the difficulty of the polymer chains to access the catalyst acid sites, occurring preferentially end-chain scission at the external surface of the catalyst.

Olefin recovery from FCC off-gas can pay off

International Nuclear Information System (INIS)

Brahn, M.G.

1992-01-01

This paper reports on olefins recovery from refinery FCC offgas streams which offers an attractive cash flow from olefins from a tail-gas stream that has typically been consumed as refinery fuel. Such recovery schemes can be employed in refineries or olefins plants, and can be tailored to fit individual requirements. Mobil Chemical Co. has operated such a dephlegmator-based off-gas recovery unit at its Beaumont, Tex., olefin plant since 1987. It reported that the project was paid out within 11 months of initial start-up

Effect of bidirectional internal flow on fluid–structure interaction dynamics of conveying marine riser model subject to shear current

Directory of Open Access Journals (Sweden)

Zheng-Shou Chen

2012-03-01

Full Text Available This article presents a numerical investigation concerning the effect of two kinds of axially progressing internal flows (namely, upward and downward on fluid–structure interaction (FSI dynamics about a marine riser model which is subject to external shear current. The CAE technology behind the current research is a proposed FSI solution, which combines structural analysis software with CFD technology together. Efficiency validation for the CFD software was carried out first. It has been proved that the result from numerical simulations agrees well with the observation from relating model test cases in which the fluidity of internal flow is ignorable. After verifying the numerical code accuracy, simulations are conducted to study the vibration response that attributes to the internal progressive flow. It is found that the existence of internal flow does play an important role in determining the vibration mode (/dominant frequency and the magnitude of instantaneous vibration amplitude. Since asymmetric curvature along the riser span emerges in the case of external shear current, the centrifugal and Coriolis accelerations owing to up- and downward internal progressive flows play different roles in determining the fluid–structure interaction response. The discrepancy between them becomes distinct, when the velocity ratio of internal flow against external shear current is relatively high.

Quench Protection Study of the Eurocircol 16 T cosθ Dipole for the Future Circular Collider (FCC)

CERN Document Server

AUTHOR|(CDS)2151660; Caiffi, Barbara; Fabbricatore, Pasquale; Farinon, Stefania; Salmi, Tiina-Mari; Sorbi, Massimo Leone; Stenvall, Antti; Volpini, Giovanni

2017-01-01

After LHC will be turned off, a new, more energetic machine will be needed in order to explore unknown regions of the high-energy physics. For this reason, the project Future Circular Collider (FCC) has started, with the goal of developing a 100 km circumference collider of 50 TeV proton beams. The Eurocircol collaboration is part of the FCC study under the European Community leadership, and it aims to develop a conceptual design of FCC within 2019. One of the main targets is to design a bending dipole able to reach 16 T operation magnetic field, in order to accomplish the size and energy constraints. Such a magnetic field can be reached using Nb$_{3}$Sn conductors at their highest performance. One option under exploration is the Cosθ dipole, by INFN of Milano and Genova. One of the aspects to be taken into consideration is the amount of conductor needed, because of the relatively high cost of superconducting cables involving Nb$_{3}$Sn. The amount of superconductor in the cross-section conductor area is a d...

NCTA v. FCC - Do Commercial Free Speech Justifications Trump Consumers' Personal Data Protection Rights? Answer To Shape Mobile Advertising Industry

DEFF Research Database (Denmark)

Cleff, Evelyne Beatrix; King, Nancy J.

2010-01-01

telecommunication carriers' personal data sharing practices in order to protect their customers' data privacy when the regulation restricts use of the data for marketing purposes. In this case National Cable and Telecommunications Association (NCTA) challenged a new Federal Communications Commission (FCC) rule...... requiring carriers to obtain customers' advance approval before releasing their telephone record information for marketing purposes. NCTA claimed the FCC's new opt-in rule violates companies' First Amendment right to engage in commercial speech. At stake in this appeal was the constitutionally required...... balance between protecting consumers' information privacy in an era of pervasive data processing and protecting the rights of marketers to engage in protected commercial free speech that involves using customers' personal information. A ruling against the FCC would have limited the use of government...

Lattice dynamics of fcc helium at high pressure

International Nuclear Information System (INIS)

Eckert, J.; Thomlinson, W.; Shirane, G.

1977-01-01

The neutron-inelastic-scattering technique was used to measure the phonon dispersion relations in a high-density crystal of fcc He at 38 K. The crystal was grown at a pressure of 4.93 kbar and a temperature of 38.5 K in a high-pressure sample holder. Its lattice parameter was determined to be 3.915 +- 0.002 A, equivalent to a molar volume of 9.03 cm 3 /mol. The measured dispersion curves were found to be in good agreement with a recent calculation by Goldman using the first-order self-consistent phonon theory without short-range correlation functions. The strong anharmonic effects observed in earlier measurements on the crystals of 21 cm 3 /mol were found to be much less prominent in this He crystal. The magnitude of the multiphonon interference effects on the one-phonon intensities is shown to be less than half of that observed in the low-density crystals. Thermodynamic analysis of the data yielded THETA/sup M//sub D/ = 154 K which indicates that the ratio of mean amplitude of vibration to the nearest-neighbor distance is 8.6%, as opposed to nearly 30% for the lowest-density He crystals. The dependence of the phonon energies on volume is discussed with reference to the earlier work of Traylor et al. on an fcc crystal at 11.7 cm 3 /mol. Limited measurements were also made at 22 K to determine the temperature dependence of the phonon energies. Unusually large isochoric temperature shifts of as much as 15% for some phonons close to the zone center were found over the range of 22--38 K

The FCC-ee Interaction Region Magnet Design

CERN Document Server

Koratzinos, Michael; Blondel, Alain; Bogomyagkov, Anton; Holzer, Bernhard; Oide, Katsunobu; Sinyatkin, Sergey; Zimmermann, Frank; van Nugteren, Jeroen

2016-01-01

The design of the region close to the interaction point of the FCC-ee experiments is especially challenging. The beams collide at an angle (+-15 mrad) in the high-field region of the detector solenoid. Moreover, the very low vertical beta_y* of the machine necessitates that the final focusing quadrupoles have a distance from the IP (L*) of around 2 m and therefore are inside the main detector solenoid. The beams should be screened from the effect of the detector magnetic field, and the emittance blow-up due to vertical dispersion in the interaction region should be minimized, while leaving enough space for detector components. Crosstalk between the two final focus quadrupoles, only about 6 cm apart at the tip, should also be minimized.

Bcc and Fcc transition metals and alloys: a central role for the Jahn-Teller effect in explaining their ideal and distorted structures.

Science.gov (United States)

Lee, Stephen; Hoffmann, Roald

2002-05-01

Transition metal elements, alloys, and intermetallic compounds often adopt the body centered cubic (bcc) and face centered cubic (fcc) structures. By comparing quantitative density functional with qualitative tight-binding calculations, we analyze the electronic factors which make the bcc and fcc structures energetically favorable. To do so, we develop a tight-binding function, DeltaE(star), a function that measures the energetic effects of transferring electrons within wave vector stars. This function allows one to connect distortions in solids to the Jahn-Teller effect in molecules and to provide an orbital perspective on structure determining deformations in alloys. We illustrate its use by considering first a two-dimensional square net. We then turn to three-dimensional fcc and bcc structures, and distortions of these. Using DeltaE(star), we rationalize the differences in energy of these structures. We are able to deduce which orbitals are responsible for instabilities in seven to nine valence electron per atom (e(-)/a) bcc systems and five and six e(-)/a fcc structures. Finally we demonstrate that these results account for the bcc and fcc type structures found in both the elements and binary intermetallic compounds of group 4 through 9 transition metal atoms. The outline of a theory of metal structure deformations based on loss of point group operation rather than translational symmetry is presented.

Enhanced propylene production in FCC by novel catalytic materials

Energy Technology Data Exchange (ETDEWEB)

Kelkar, C.P.; Harris, D.; Xu, M.; Fu, J. [BASF Catalyst LLC, Iselin, NJ (United States)

2007-07-01

Fluid catalytic cracking is expected to increasingly supply the additional incremental requirements for propylene. The most efficient route to increase propylene yield from an FCC unit is through the use of medium pore zeolites such as ZSM-5. ZSM-5 zeolite cracks near linear olefins in the gasoline range to LPG olefins such as propylene and butylenes. This paper will describe catalytic approaches to increase gasoline range olefins and the chemistry of ZSM-5 to crack those olefins. The paper will also describe novel catalytic materials designed to increase propylene. (orig.)

Design of an Inductive Adder for the FCC injection kicker pulse generator

Science.gov (United States)

Woog, D.; Barnes, M. J.; Ducimetière, L.; Holma, J.; Kramer, T.

2017-07-01

The injection system for a 100 TeV centre-of-mass collider is an important part of the Future Circular Collider (FCC) study. Due to issues with conventional kicker systems, such as self-triggering and long term availability of thyratrons and limitations of HV-cables, innovative design changes are planned for the FCC injection kicker pulse generator. An inductive adder (IA) based on semiconductor (SC) switches is a promising technology for kicker systems. Its modular design, and the possibility of an active ripple suppression are significant advantages. Since the IA is a complex device, with multiple components whose characteristics are important, a detailed design study and construction of a prototype is necessary. This paper summarizes the system requirements and constraints, and describes the main components and design challenges of the prototype IA. It outlines the results from simulations and measurements on different magnetic core materials as well as on SC switches. The paper concludes on the design choices and progress for the prototype to be built at CERN.

Ab initio random structure search for 13-atom clusters of fcc elements

International Nuclear Information System (INIS)

Chou, J P; Hsing, C R; Wei, C M; Cheng, C; Chang, C M

2013-01-01

The 13-atom metal clusters of fcc elements (Al, Rh, Ir, Ni, Pd, Pt, Cu, Ag, Au) were studied by density functional theory calculations. The global minima were searched for by the ab initio random structure searching method. In addition to some new lowest-energy structures for Pd 13 and Au 13 , we found that the effective coordination numbers of the lowest-energy clusters would increase with the ratio of the dimer-to-bulk bond length. This correlation, together with the electronic structures of the lowest-energy clusters, divides the 13-atom clusters of these fcc elements into two groups (except for Au 13 , which prefers a two-dimensional structure due to the relativistic effect). Compact-like clusters that are composed exclusively of triangular motifs are preferred for elements without d-electrons (Al) or with (nearly) filled d-band electrons (Ni, Pd, Cu, Ag). Non-compact clusters composed mainly of square motifs connected by some triangular motifs (Rh, Ir, Pt) are favored for elements with unfilled d-band electrons. (paper)

Tunneling anisotropic magnetoresistance in Co/AIOx/Al tunnel junctions with fcc Co (111) electrodes

NARCIS (Netherlands)

Wang, Kai; Tran, T. Lan Ahn; Brinks, Peter; Brinks, P.; Sanderink, Johannes G.M.; Bolhuis, Thijs; van der Wiel, Wilfred Gerard; de Jong, Machiel Pieter

2013-01-01

Tunneling anisotropic magnetoresistance (TAMR) has been characterized in junctions comprised of face-centered cubic (fcc) Co (111) ferromagnetic electrodes grown epitaxially on sapphire substrates, amorphous AlOx tunnel barriers, and nonmagnetic Al counterelectrodes. Large TAMR ratios have been

75 FR 34450 - FCC to Hold Open Commission Meeting Thursday, June 17, 2010

Science.gov (United States)

2010-06-17

..., and bring the benefits of broadband to all Americans. The meeting site is fully accessible to people... www.capitolconnection.gmu.edu http://www.capitolconnection.gmu.edu/ >. Copies of materials adopted at this meeting can be purchased from the FCC's duplicating contractor, Best Copy and Printing, Inc. (202...

First-principles calculation of the magnetic properties of paramagnetic fcc iron

International Nuclear Information System (INIS)

Johnson, D.D.; Gyorffy, B.L.; Pinski, F.J.; Staunton, J.; Stocks, G.M.

1985-01-01

Using the disordered local moment picture of itinerant magnetism, we present calculations of the temperature and volume dependence of the magnetic moment and spin-spin correlations for fcc Fe in the paramagnetic state. These calculations are based on the parameter-free, first principles approach of local spin density functional theory and the coherent potential approximation is used to treat the disorder associated with the random orientation of the local moments

Optimising A Read Out for A Possible FCC hh Collision

CERN Document Server

Alagaraisamy, Revathy

2017-01-01

The Future Circular Collider Study (FCC) aims to provide a conceptual design for an accelerator to possibly be constructed in the 2040s-2050s. The most ambitious design proposed is a 100 km-circumference proton-proton collider (FCChh), designed to achieve a centre-of-mass energy of 100 TeV and exceeding . Thus,along with this the precision of the detector is increased via many ways,e.g: calculation and reduction of electronic noise with PCB readout in detector.

Recovery of Frenkel defects in fcc metals

International Nuclear Information System (INIS)

Chaplin, R.L.; Miller, M.G.

1976-01-01

Because of the production of Frenkel defects occurs most readily along specific crystallographic directions in fcc structures, the recovery mechanism by which annihilation occurs should also be related to the same crystallographic orientations. The recovery path of a diffusing interstitial requires the formation of a temporary metastable state as a close-pair Frenkel defect prior to annihilation. A theoretical treatment of this scheme for interstitial-vacancy recombination shows that during the Isub(D) diffusion there is an experimentally measurable difference if the recovery forms a Isub(B) or a Isub(C) close-pair configuration in aluminum. Experimental results are given which show a difference from the theoretical predictions, and it is concluded that the assumed analytical function describing the interstitial-vacancy distribution created by a 0.4 MeV electron irradiation should be modified. (author)

Influence of Addition of Fluid Catalytic Cracking Residue (FCC and the SiO2 Concentration in Alkali-Activated Ceramic Sanitary-Ware (CSW Binders

Directory of Open Access Journals (Sweden)

Juan Cosa

2018-03-01

Full Text Available Production of Portland cement requires a large volume of natural raw materials and releases huge amounts of CO2 to the atmosphere. Lower environmental impact alternatives focus on alkali-activated cements. In this paper, fluid catalytic cracking residue (FCC was used to partially replace (0 wt %–50 wt % ceramic sanitaryware (CSW in alkali-activated systems. Samples were activated with NaOH and sodium silicate solutions and were cured at 65 °C for 7 days and at 20 °C for 28 and 90 days. In order to increase CSW/FCC binders’ sustainability, the influence of reducing the silica concentration (from 7.28 mol·kg−1 up to 2.91 mol·kg−1 was analyzed. The microstructure of the developed binders was investigated in pastes by X-ray diffraction, thermo tests and field emission scanning electron microscopy analyses. Compressive strength evolution was assessed in mortars. The results showed a synergetic effect of the CSW/FCC combinations so that, under the studied conditions, mechanical properties significantly improved when combining both waste materials (up to 70 MPa were achieved in the mortars containing 50 wt % FCC cured at room temperature for 90 days. Addition of FCC allowed CSW to be activated at room temperature, which significantly broadens the field of applications of alkali-activated CSW binders.

Martensitic transformation, fcc and hcp relative phase stability, and thermal cycling effects in Fe-Mn and Fe-Mn-X Alloys (X = Si, Co)

International Nuclear Information System (INIS)

Baruj, Alberto

1999-01-01

In this Thesis we present a study of the fcc and hcp relative phase stability in the Fe-Mn and Fe-Mn-Co systems. In particular, we have investigated the effect of two main factors affecting the relative phase stability: changes in the chemical composition of the alloys and changes in the density of crystalline defects in the microstructure.In order to analyse the effect of chemical composition, we have performed an experimental study of the fcc/hcp martensitic transformation temperatures in Fe-Mn-Co alloys in the composition range lying between 15% and 34% Mn, and between 1% and 16% Co.We have measured the martensitic transformation temperatures by means of dilatometry and electrical resistivity.We have combined this information with measurements of the fcc/hcp martensitic transformation temperatures in Co-rich alloys to perform a modelling of the Gibbs energy function for the hcp phase in the Fe-Mn-Co and Fe-Co systems.We found that, for alloys in the Mn range between 17% and 25%, Co additions tend to stabilise slightly the fcc phase.In the alloys with Mn contents below that range, increasing the amount of Co stabilise the bcc phase. In alloys with Mn contents above 25% the Neel temperature is depressed by the addition of Co, which stabilise the hcp phase.In order to investigate the effect of changes in the density of crystalline defects, we have performed thermal cycling experiments through the fcc/hcp martensitic transformation in Fe-Mn, Fe-Mn-Co and Fe-Mn-Si alloys.We have applied the thermodynamic description obtained before in order to analyse these experiments.We found in the thermal cycling experiments a first stage where the martensitic transformation is promoted.This stage occurs in all the studied alloys during the first cycle or the two first cycles.Increasing the number of thermal cycles, the promotion stage is replaced by an inhibition of the transformation stage.We propose a possible microstructural interpretation of these phenomena where the plastic

ESTUDIO COMPARATIVO DE PASTAS DE CEMENTO ADICIONADAS CON CATALIZADOR DE CRAQUEO CATALÍTICO USADO (FCC, Y METACAOLIN (MK

Directory of Open Access Journals (Sweden)

Janneth Torres Agredo

2012-01-01

Full Text Available Este artículo es parte de un proyecto de investigación cuyo objetivo principal es evaluar el desempeño de un residuo de una refinería de petróleo, como adición al cemento Portland con el fin de establecer la viabilidad de su aplicación en materiales de construcción. Este residuo denominado catalizador usado a partir del proceso de craqueo catalítico (fcc procede de las unidades de ruptura catalítica en lecho fluido y está compuesto principalmente por sílice y alúmina. Se analizó la hidratación en pastas de cemento adicionadas con el fcc, y se hizo una comparación con la adición de metacaolín (mk. Para realizar el estudio, se prepararon pastas de cemento Portland Ordinario (opc, adicionadas en porcentajes del 10 y 20% de fcc y mk como reemplazo de cemento. La actividad puzolánica de las adiciones y el tipo de productos de hidratación se determinaron mediante las técnicas de difracción de rayos X (drx y del análisis termogravimétrico (tg/dtg. Como fases principales del proceso de hidratación en las pastas adicionadas con fcc se encontraron silicatos cálcicos hidratados (csh, aluminatos cálcicos hidratados (cah, y silico aluminatos cálcicos (cash, productos similares a los obtenidos en pastas adicionadas con metacaolín.

Measurement of Gas Velocities in the Presence of Solids in the Riser of a Cold Flow Circulating Fluidized Bed

International Nuclear Information System (INIS)

Spenik, J.; Ludlow, J.C.; Compston, R.; Breault, R.W.

2007-01-01

The local gas velocity and the intensity of the gas turbulence in a gas/solid flow are a required measurement in validating the gas and solids flow structure predicted by computational fluid dynamic (CFD) models in fluid bed and transport reactors. The high concentration and velocities of solids, however, make the use of traditional gas velocity measurement devices such as pitot tubes, hot wire anemometers and other such devices difficult. A method of determining these velocities has been devised at the National Energy Technology Laboratory employing tracer gas. The technique developed measures the time average local axial velocity gas component of a gas/solid flow using an injected tracer gas which induces changes in the heat transfer characteristics of the gas mixture. A small amount of helium is injected upstream a known distance from a self-heated thermistor. The thermistor, protected from the solids by means of a filter, is exposed to gases that are continuously extracted from the flow. Changes in the convective heat transfer characteristics of the gas are indicated by voltage variations across a Wheatstone bridge. When pulsed injections of helium are introduced to the riser flow the change in convective heat transfer coefficient of the gas can be rapidly and accurately determined with this instrument. By knowing the separation distance between the helium injection point and the thermistor extraction location as well as the time delay between injection and detection, the gas velocity can easily be calculated. Variations in the measured gas velocities also allow the turbulence intensity of the gas to be estimated

Numerical modelling of micro-machining of f.c.c. single crystal: Influence of strain gradients

KAUST Repository

Demiral, Murat; Roy, Anish; El Sayed, Tamer S.; Silberschmidt, Vadim V.

2014-01-01

of orthogonal micro-machining of f.c.c. single crystal copper was developed. The model was implemented in a commercial software ABAQUS/Explicit employing a user-defined subroutine VUMAT. Strain-gradient crystal-plasticity and conventional crystal

Effects of Dynamic Impact Loading on Microstructure of FCC (TWIP) Steel

Science.gov (United States)

2014-08-01

the plate to the maximum bulge at the centre of the plate after a blast. Figure 2 shows the aluminium bulge depth measuring device in which the...is shown in Table 1. The most notable feature of the steel is the high level of manganese (18%) combined with significant levels of aluminium ...representatively in the current investigation. Figure 9(a) shows the typical rolling texture components in FCC alloys [12] as reference, consisting of ideal

A Novel FCC Catalyst Based on a Porous Composite Material Synthesized via an In Situ Technique

Directory of Open Access Journals (Sweden)

Shu-Qin Zheng

2015-11-01

Full Text Available To overcome diffusion limitations and improve transport in microporous zeolite, the materials with a wide-pore structure have been developed. In this paper, composite microspheres with hierarchical porous structure were synthesized by an in situ technique using sepiolite, kaolin and pseudoboehmite as raw material. A novel fluid catalytic cracking (FCC catalyst for maximizing light oil yield was prepared based on the composite materials. The catalyst was characterized by XRD, FT-IR, SEM, nitrogen adsorption-desorption techniques and tested in a bench FCC unit. The results indicated that the catalyst had more meso- and macropores and more acid sites than the reference catalyst, and thus can increase light oil yield by 1.31 %, while exhibiting better gasoline and coke selectivity.

Design and performance of an electromagnetic calorimeter for a FCC-hh experiment

Science.gov (United States)

Zaborowska, A.

2018-03-01

The physics reach and feasibility of the Future Circular Collider are currently under investigation. The goal is to collide protons with centre-of-mass energies up to 100 TeV, extending the research carried out at the current HEP facilities. The detectors designed for the FCC experiments need to tackle harsh conditions of the unprecedented collision energy and luminosity. The baseline technology for the calorimeter system of the FCC-hh detector is described. The electromagnetic calorimeter in the barrel, as well as the electromagnetic and hadronic calorimeters in the endcaps and the forward regions, are based on the liquid argon as active material. The detector layout in the barrel region combines the concept of a high granularity calorimeter with precise energy measurements. The calorimeters have to meet the requirements of high radiation hardness and must be able to deal with a very high number of collisions per bunch crossings (pile-up). A very good energy and angular resolution for a wide range of electrons' and photons' momentum is needed in order to meet the demands based on the physics benchmarks. First results of the performance studies with the new liquid argon calorimeter are presented, meeting the energy resolution goal.

Microstructure and mechanical properties of bulk highly faulted fcc/hcp nanostructured cobalt microstructures

Energy Technology Data Exchange (ETDEWEB)

Barry, Aliou Hamady [Université Paris 13, Sorbonne Paris Cité, LSPM CNRS UPR 3407, 93430 Villetaneuse (France); Laboratoire Chimie des Matériaux, Département de Chimie, Faculté des Sciences et Technique, Université de Nouakchott (Mauritania, Islamic Republic of); Dirras, Guy, E-mail: dirras@unv-paris13.fr [Université Paris 13, Sorbonne Paris Cité, LSPM CNRS UPR 3407, 93430 Villetaneuse (France); Schoenstein, Frederic; Tétard, Florent; Jouini, Noureddine [Université Paris 13, Sorbonne Paris Cité, LSPM CNRS UPR 3407, 93430 Villetaneuse (France)

2014-05-01

Nanostructured cobalt powders with an average particle size of 50 nm were synthesized using a polyol method and subsequently consolidated by spark plasma sintering (SPS). SPS experiments performed at 650 °C with sintering times ranging from 5 to 45 min under a pressure of 100 MPa, yielded to dense bulk nanostructured cobalt (relative density greater than 97%). X-ray diffraction patterns of the as-prepared powders showed only a face centered cubic (fcc) crystalline phase, whereas the consolidated samples exhibited a mixture of both fcc and hexagonal close packed (hcp) phases. Transmission electron microscopy observations revealed a lamellar substructure with a high density of nanotwins and stacking faults in every grain of the sintered samples. Room temperature compression tests, carried out at a strain rate of 10{sup −3} s{sup −1}, yielded to highest strain to fracture values of up to 5% for sample of holding time of 15 min, which exhibited a yield strength of 1440 MPa, an ultimate strength as high as 1740 MPa and a Young's modulus of 205 GPa. The modulus of elasticity obtained from the nanoindentation tests, ranges from 181 to 218 GPa. The lowest modulus value of 181 GPa was obtained for the sample with the highest sintering time (45 min), which could be related to mass density loss as a consequence of trapped gases releasing. - Highlights: • Co nanopowder (50 nm) was prepared by reduction in polyol medium. • SPS was used to process bulk nanostructured Co specimens. • Microstructures were made of intricate fcc/hcp, along with nanotwins and SFs. • High strengths and moderate compressive ductility were obtained. • Deformation mechanisms related to complex interplay of different length scales.

Diffusion coefficients of rare earth elements in fcc Fe: A first-principles study

Science.gov (United States)

Wang, Haiyan; Gao, Xueyun; Ren, Huiping; Chen, Shuming; Yao, Zhaofeng

2018-01-01

The diffusion data and corresponding detailed insights are particularly important for the understanding of the related kinetic processes in Fe based alloys, e.g. solute strengthening, phase transition, solution treatment etc. We present a density function theory study of the diffusivity of self and solutes (La, Ce, Y and Nb) in fcc Fe. The five-frequency model was employed to calculate the microscopic parameters in the correlation factors of the solute diffusion. The interactions of the solutes with the first nearest-neighbor vacancy (1nn) are all attractive, and can be well understood on the basis of the combination of the strain-relief effects and the electronic effects. It is found that among the investigated species, Ce is the fastest diffusing solute in fcc Fe matrix followed by Nb, and the diffusion coefficients of these two solutes are about an order of magnitude higher than that of Fe self-diffusion. And the results show that the diffusion coefficient of La is slightly higher than that of Y, and both species are comparable to that of Fe self-diffusion.

Nature of nitrogen specie in coke and their role in NOx formation during FCC catalyst regeneration

International Nuclear Information System (INIS)

Babich, I.V.; Seshan, K.; Lefferts, L.

2005-01-01

NO x emission during the regeneration of coked fluid catalytic cracking (FCC) catalysts is an environmental problem. In order to follow the route to NO x formation and try to find ways to suppress it, a coked industrial FCC catalyst has been prepared using model N-containing compounds, e.g., pyridine, pyrrole, aniline and hexadecane-pyridine mixture. Nitrogen present in the FCC feed is incorporated as polyaromatic compounds in the coke deposited on the catalyst during cracking. Its functionality has been characterized using XPS. Nitrogen specie of different types, namely, pyridine, pyrrolic or quaternary-nitrogen (Q-N) have been discriminated. Decomposition of the coke during the catalyst regeneration (temperature programmed oxidation (TPO) and isothermal oxidation) has been monitored by GC and MS measurements of the gaseous products formed. The pyrrolic- and pyridinic-type N specie, present more in the outer coke layers, are oxidized under conditions when still large amount of C or CO is available from coke to reduced NO x formed to N 2 . ''Q-N'' type species are present in the inner layer, strongly adsorbed on the acid sites on the catalyst. They are combusted last during regeneration. As most of the coke is already combusted at this point, lack of reductants (C, CO, etc.) results in the presence of NO x in the tail gas

evaluation of commercial FCC catalysts for hydrocarbon conversion. I. Physicochemical characterization and n-hexane conversion.

NARCIS (Netherlands)

Brait, A.; Brait, A.; Seshan, Kulathuiyer; Lercher, J.A.

1998-01-01

The physicochemical properties of six steam-stabilized, commercial FCC catalysts were compared in respect of their catalytic activity for n-hexane conversion. The conversion of n-hexane over these catalysts could be fully explained by three reaction pathways: protolytic cracking, protolytic

Physics Perspectives for a Future Circular Collider: FCC-hh - Accelerator & Detectors

CERN Multimedia

CERN. Geneva

2017-01-01

The lectures will briefly discuss the parameters of a Future Circular Collider, before addressing in detail the physics perspectives and the challenges for the experiments and detector systems. The main focus will be on ee and pp collisions, but opportunities for e—p physics will also be covered. The FCC physics perspectives will be presented with reference to the ongoing LHC programme, including the physics potential from future upgrades to the LHC in luminosity and possibly energy.

CFD Model Development and validation for High Temperature Gas Cooled Reactor Cavity Cooling System (RCCS) Applications

International Nuclear Information System (INIS)

Hassan, Yassin; Corradini, Michael; Tokuhiro, Akira; Wei, Thomas Y.C.

2014-01-01

The Reactor Cavity Cooling Systems (RCCS) is a passive safety system that will be incorporated in the VTHR design. The system was designed to remove the heat from the reactor cavity and maintain the temperature of structures and concrete walls under desired limits during normal operation (steady-state) and accident scenarios. A small scale (1:23) water-cooled experimental facility was scaled, designed, and constructed in order to study the complex thermohydraulic phenomena taking place in the RCCS during steady-state and transient conditions. The facility represents a portion of the reactor vessel with nine stainless steel coolant risers and utilizes water as coolant. The facility was equipped with instrumentation to measure temperatures and flow rates and a general verification was completed during the shakedown. A model of the experimental facility was prepared using RELAP5-3D and simulations were performed to validate the scaling procedure. The experimental data produced during the steady-state run were compared with the simulation results obtained using RELAP5-3D. The overall behavior of the facility met the expectations. The facility capabilities were confirmed to be very promising in performing additional experimental tests, including flow visualization, and produce data for code validation.

CFD Model Development and validation for High Temperature Gas Cooled Reactor Cavity Cooling System (RCCS) Applications

Energy Technology Data Exchange (ETDEWEB)

Hassan, Yassin [Univ. of Wisconsin, Madison, WI (United Texas A & M Univ., College Station, TX (United States); Corradini, Michael; Tokuhiro, Akira; Wei, Thomas Y.C.

2014-07-14

The Reactor Cavity Cooling Systems (RCCS) is a passive safety system that will be incorporated in the VTHR design. The system was designed to remove the heat from the reactor cavity and maintain the temperature of structures and concrete walls under desired limits during normal operation (steady-state) and accident scenarios. A small scale (1:23) water-cooled experimental facility was scaled, designed, and constructed in order to study the complex thermohydraulic phenomena taking place in the RCCS during steady-state and transient conditions. The facility represents a portion of the reactor vessel with nine stainless steel coolant risers and utilizes water as coolant. The facility was equipped with instrumentation to measure temperatures and flow rates and a general verification was completed during the shakedown. A model of the experimental facility was prepared using RELAP5-3D and simulations were performed to validate the scaling procedure. The experimental data produced during the steady-state run were compared with the simulation results obtained using RELAP5-3D. The overall behavior of the facility met the expectations. The facility capabilities were confirmed to be very promising in performing additional experimental tests, including flow visualization, and produce data for code validation.

Comparison of Mechanical Properties of Ni[sub]3Al Thin Films in Disordered FCC and Ordered L1[sub]2 Phases

OpenAIRE

Nix, Wiliam D.; Saha, R.; Aziz, Michael; Hutchinson, John; Evans, Anthony G.; Huang, Yonggang

2001-01-01

We report the results of several experiments isolating the effect of long-range order on mechanical properties of intermetallic compounds. Kinetically disordered FCC Ni3Al (Ni 76%) thin films were produced by rapid solidification following pulsed laser melting. For comparison, compositionally and microstructurally identical films with ordered L12 structure were produced by subsequent annealing at 550 °C for 2 hours. These FCC and L12 Ni3Al thin films were tested by nanoindentation for hardnes...

EFFECT OF VANADIUM ON THE DEACTIVATION OF FCC CATALYSTS

Directory of Open Access Journals (Sweden)

Roncolatto R.E

1998-01-01

Full Text Available This work provides concrete evidence that vanadium causes the destruction of the zeolite in the FCC catalysts by a mechanism of acid attack or solid-solid transformation, as well as additional dealumination of the zeolite framework in the presence of steam and at high temperature. While these effects resulted in the reduction in crystallinity (zeolite Y content, specific area and unit cell size of the Y zeolite as the amount of vanadium in the catalysts increased, the reduction in activity was the most pronounced. The differences in these behaviors were interpreted and the model can be used for better catalyst formulation or screening.

Gibbs energy modelling of the driving forces and calculation of the fcc/hcp martensitic transformation temperatures in Fe-Mn and Fe-Mn-Si alloys

International Nuclear Information System (INIS)

Cotes, S.; Fernandez Guillermet, A.; Sade, M.

1999-01-01

Very recent, accurate dilatometric measurements of the fcc hcp martensitic transformation (MT) temperatures are used to develop a new thermodynamic description of the fcc and hcp phases in the Fe-Mn-Si system, based on phenomenological models for the Gibbs energy function. The composition dependence of the driving forces for the fcc→hcp and the hcp→fcc MTs is established. Detailed calculations of the MT temperatures are reported, which are used to investigate the systematic effects of Si additions upon the MT temperatures of Fe-Mn alloys. A critical comparison with one of the most recent thermodynamic analyses of the Fe-Mn-Si system, which is due to Forsberg and Agren, is also presented. (orig.)

A systematic study on the interfacial energy of O-line interfaces in fcc/bcc systems

International Nuclear Information System (INIS)

Dai, Fuzhi; Zhang, Wenzheng

2013-01-01

Habit planes between face-centered cubic (fcc)/body-centered cubic (bcc) phases usually exhibit irrational orientations, which often agree with the O-line criterion. Previously, energy calculation was made to test whether the habit planes were energetically favorable, but the values of the energy were found very sensitive to the initial atomic configuration in an irrationally orientated interface. In this paper, under the O-line condition, simple selection criteria are proposed to define and remove interfacial interstitials and vacancies in the initial atomic configuration. The criteria are proved to be effective in obtaining robust energy results. Interfacial energies of two types of O-line interfaces in fcc/bcc systems are calculated following the criteria. The observed transformation crystallography of precipitates in Ni–Cr and Cu–Cr systems can be explained consistently as the irrational habit plane in each system is associated with the lowest energy O-line interface. (paper)

FCC Rolling Textures Reviewed in the Light of Quantitative Comparisons between Simulated and Experimental Textures

DEFF Research Database (Denmark)

Wierzbanowski, Krzysztof; Wroński, Marcin; Leffers, Torben

2014-01-01

The crystallographic texture of metallic materials has a very strong effect on the properties of the materials. In the present article, we look at the rolling textures of fcc metals and alloys, where the classical problem is the existence of two different types of texture, the "copper-type texture......" and the "brass-type texture." The type of texture developed is determined by the stacking fault energy of the material, the rolling temperature and the strain rate of the rolling process. Recent texture simulations by the present authors provide the basis for a renewed discussion of the whole field of fcc......} slip without or with deformation twinning, but we also consider slip on other slip planes and slip by partial dislocations. We consistently make quantitative comparison of the simulation results and the experimental textures by means of a scalar correlation factor. We find that the development...

Regulation of Fumonisin B1 Biosynthesis and Conidiation in Fusarium verticillioides by a Cyclin-Like (C-Type) Gene, FCC1†

Science.gov (United States)

Shim, Won-Bo; Woloshuk, Charles P.

2001-01-01

Fumonisins are a group of mycotoxins produced in corn kernels by the plant-pathogenic fungus Fusarium verticillioides. A mutant of the fungus, FT536, carrying a disrupted gene named FCC1 (for Fusarium cyclin C1) resulting in altered fumonisin B1 biosynthesis was generated. FCC1 contains an open reading frame of 1,018 bp, with one intron, and encodes a putative 319-amino-acid polypeptide. This protein is similar to UME3 (also called SRB11 or SSN8), a cyclin C of Saccharomyces cerevisiae, and contains three conserved motifs: a cyclin box, a PEST-rich region, and a destruction box. Also similar to the case for C-type cyclins, FCC1 was constitutively expressed during growth. When strain FT536 was grown on corn kernels or on defined minimal medium at pH 6, conidiation was reduced and FUM5, the polyketide synthase gene involved in fumonisin B1 biosynthesis, was not expressed. However, when the mutant was grown on a defined minimal medium at pH 3, conidiation was restored, and the blocks in expression of FUM5 and fumonisin B1 production were suppressed. Our data suggest that FCC1 plays an important role in signal transduction regulating secondary metabolism (fumonisin biosynthesis) and fungal development (conidiation) in F. verticillioides. PMID:11282612

Stacking fault growth of FCC crystal: The Monte-Carlo simulation approach

International Nuclear Information System (INIS)

Jian Jianmin; Ming Naiben

1988-03-01

The Monte-Carlo method has been used to simulate the growth of the FCC (111) crystal surface, on which is presented the outcrop of a stacking fault. The comparison of the growth rates has been made between the stacking fault containing surface and the perfect surface. The successive growth stages have been simulated. It is concluded that the outcrop of stacking fault on the crystal surface can act as a self-perpetuating step generating source. (author). 7 refs, 3 figs

78 FR 49480 - Proposed Information Collection; Comment Request; NTIA/FCC Web-based Frequency Coordination System

Science.gov (United States)

2013-08-14

... Information Collection; Comment Request; NTIA/FCC Web- based Frequency Coordination System AGENCY: National... the data by means of an internet web-based system. The applications on the Web site provide real-time... INFORMATION: I. Abstract The National Telecommunications and Information Administration (NTIA) hosts a web...

75 FR 42376 - Proposed Information Collection; Comment Request; NTIA/FCC Web-based Frequency Coordination System

Science.gov (United States)

2010-07-21

... Information Collection; Comment Request; NTIA/FCC Web- based Frequency Coordination System AGENCY: National.... Abstract The National Telecommunications and Information Administration (NTIA) hosts a Web-based system...) bands that are shared on a co-primary basis by federal and non-federal users. The Web-based system...

Stability and ordering properties of fcc alloys based on Rh, Ir, Pd, and Pt

Czech Academy of Sciences Publication Activity Database

Turchi, P. E. A.; Drchal, Václav; Kudrnovský, Josef

2006-01-01

Roč. 74, č. 6 (2006), 064202/1-064202/12 ISSN 1098-0121 Institutional research plan: CEZ:AV0Z10100520; CEZ:AV0Z1010914 Keywords : alloy phase stability * ordering in alloys * fcc alloys of Rh, Ir, Pd, Pt Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 3.107, year: 2006

The impact of the Family Communication Coordinator (FCC) Protocol on the role stress of hospital chaplains.

Science.gov (United States)

Dodd-McCue, Diane; Tartaglia, Alexander

2005-01-01

The Family Communication Coordinator (FCC) Protocol was implemented to provide early family intervention and to facilitate effective communications during potential organ donation cases. Previous studies found the Protocol associated with improved donor outcome measures and with reduced role stress for ICU nurses caring for potential donors. The present study examines the impact of the Protocol on the perceived role stress of hospital chaplains serving as FCCs. All hospital chaplains serving as FCCs at an academic teaching hospital were surveyed. Their perceptions of job dimensions, role stress, job satisfaction, and commitment were measured; interviews and secondary data supplemented the surveys. The findings demonstrate that the FCC Protocol is associated with improved role stress, specifically role ambiguity and role conflict, among hospital chaplains serving as FCCs. Additionally, the findings suggest that satisfaction with the Protocol may be associated with experience with the Protocol.

Commercial application of titania-supported hydrodesulfurization catalysts in the production of hydrogen using full-range FCC off-gas

Energy Technology Data Exchange (ETDEWEB)

Wang, Shaohu [SINOPEC Wuhan Branch, Qingshan, Wuhan 430082 (China); Shen, Binglong; Qu, Lianglong [Beijing Haishunde Titanium Catalyst Co. Ltd., A-1 North East-Ring Road, Beijing Economic-Technological Development Area, Beijing 100176 (China)

2004-11-24

This paper provides an alternative for low-cost feed used for on-purpose hydrogen production. Full-range FCC off-gas was applied to steam-reforming process as feed after treating with hydrogenation and hydrodesulfurization catalysts. Commercial run results were reported with novel TiO{sub 2}-supported Mo-based catalysts, T205A-1 and T205. The processes of catalysts loading, sulfidation, start-up and long-term run were described in details. Long-term run showed that TiO{sub 2}-supported Mo catalysts have good low-temperature hydrogenation activity, excellent HDS activity, and outstanding stability. Use of FCC off-gas as feed for hydrogen production is quite promising and will increase margins for refiners today.

Ab initio study on the thermal properties of the fcc Al3Mg and Al3Sc alloys

International Nuclear Information System (INIS)

Li Donglin; Chen Ping; Yi Jianxiong; Tang Biyu; Peng Liming; Ding Wenjiang

2009-01-01

Ab initio density functional theory (DFT) and density function perturbation theory (DFPT) have been used to investigate the thermal properties of the fcc Al 3 Mg and Al 3 Sc alloys over a wide range of pressure and temperature, in comparison with fcc Al. Phonon dispersions were obtained at equilibrium and strained configurations by density functional perturbation theory. Using the quasiharmonic approximation for the free energy, several thermal quantities of interest, such as the thermal Grueneisen parameter, heat capacity, thermal expansion coefficient and entropy, were calculated as a function of temperature and pressure, and the variation features of these quantities were discussed in detail. This investigation provides useful information for design and applications of technologically relevant Al-based alloys.

Phase transition of the FCC Ising ferromagnet with competing interactions

International Nuclear Information System (INIS)

Oh, J.H.; Lee, J.Y.; Kim, D.C.

1984-01-01

A molecular field theory with correlation and Monte Carlo simulations are utilized to determine the zero field phase diagram of a fcc Ising model with ferromagnetic nearest neighbor(-J) and antiferromagnetic next neighbor (*aJ) interactions. The correlated molecular field theory predicts a fluctuation induced first order phase transition for 0.87<*a<1.31. Monte Carlo analysis indicates that the first order transition occurs for a somewhat wider range of *a. The transition temperatures obtained by the two methods are in good agreement especially near *a=1 where the fluctuation effect is expected to be large. (Author)

A case study in flow assurance of a pipeline-riser system using OLGA

Energy Technology Data Exchange (ETDEWEB)

Nemoto, Rafael Horschutz; Balino, Jorge Luis [Nucleo de Dinamica e Fluidos. Dept. de Engenharia Mecanica. Universidade de Sao Paulo (EP/USP), SP (Brazil)], e-mails: rafael.nemoto@usp.br, jlbalino@usp.br; Tanaka, Rafael Loureiro; Godinho, Carlos Alberto [Prysmian Cables and Systems, Cariacica, ES (Brazil)], e-mails: rafael.tanaka@prysmian.com, carlos.godinho@prysmian.com

2010-07-01

In this paper, a case study in flow assurance is performed considering an offshore operating system, using the software OLGA. As operating system we consider a pipeline-riser geometry with typical dimensions of offshore oil production systems, and a three-phase flow of oil, gas and water. The model developed in OLGA considers the composition and dimensions of the tubes, heat transfer parameters, process equipment and fluid sources. The fluids properties are calculated using the software PVTsim. Simulations are ran in order to determine the pipeline inner diameter and insulation required to satisfy pressure and temperature requirements. It is also possible to simulate the transient behavior of the system, which allows to evaluate if production instabilities are present. In case instabilities exist, two mitigation alternatives are evaluated: closure of a choke valve before the separator and gas lift. Considering a possible production shutdown, the tubes insulation is calculated in order to avoid hydrate formation. (author)

Development of local shear bands and orientation gradients in fcc polycrystals

International Nuclear Information System (INIS)

Beaudoin, A.J. Jr.; Mecking, H.; Kocks, U.F.

1995-01-01

A finite element formulation which derives constitutive response from crystal plasticity theory is used to examine localized deformation in fcc polycrystals. The polycrystals are simple, idealized arrangements of grains. Localized deformations within individual grains lead to the development of domains that are separated by boundaries of high misorientation. Shear banding is seen to occur on a microscopic scale of grain dimensions. The important consequences of these simulations are that the predicted local inhomogeneities are meeting various requirements which make them possible nucleation sites for recrystallization

Photonic generation of FCC-compliant UWB pulses based on modified Gaussian quadruplet and incoherent wavelength-to-time conversion

Science.gov (United States)

Mu, Hongqian; Wang, Muguang; Tang, Yu; Zhang, Jing; Jian, Shuisheng

2018-03-01

A novel scheme for the generation of FCC-compliant UWB pulse is proposed based on modified Gaussian quadruplet and incoherent wavelength-to-time conversion. The modified Gaussian quadruplet is synthesized based on linear sum of a broad Gaussian pulse and two narrow Gaussian pulses with the same pulse-width and amplitude peak. Within specific parameter range, FCC-compliant UWB with spectral power efficiency of higher than 39.9% can be achieved. In order to realize the designed waveform, a UWB generator based on spectral shaping and incoherent wavelength-to-time mapping is proposed. The spectral shaper is composed of a Gaussian filter and a programmable filter. Single-mode fiber functions as both dispersion device and transmission medium. Balanced photodetection is employed to combine linearly the broad Gaussian pulse and two narrow Gaussian pulses, and at same time to suppress pulse pedestals that result in low-frequency components. The proposed UWB generator can be reconfigured for UWB doublet by operating the programmable filter as a single-band Gaussian filter. The feasibility of proposed UWB generator is demonstrated experimentally. Measured UWB pulses match well with simulation results. FCC-compliant quadruplet with 10-dB bandwidth of 6.88-GHz, fractional bandwidth of 106.8% and power efficiency of 51% is achieved.

NiFe epitaxial films with hcp and fcc structures prepared on bcc-Cr underlayers

Energy Technology Data Exchange (ETDEWEB)

Higuchi, Jumpei, E-mail: higuchi@futamoto.elect.chuo-u.ac.jp [Faculty of Science and Engineering, Chuo University, 1-13-27 Kasuga, Bunkyo-ku, Tokyo 112-8551 (Japan); Ohtake, Mitsuru; Sato, Yoichi [Faculty of Science and Engineering, Chuo University, 1-13-27 Kasuga, Bunkyo-ku, Tokyo 112-8551 (Japan); Kirino, Fumiyoshi [Graduate School of Fine Arts, Tokyo National University of Fine Arts and Music, 12-8 Ueno-koen, Taito-ku, Tokyo 110-8714 (Japan); Futamoto, Masaaki [Faculty of Science and Engineering, Chuo University, 1-13-27 Kasuga, Bunkyo-ku, Tokyo 112-8551 (Japan)

2011-09-30

NiFe epitaxial films are prepared on Cr(211){sub bcc} and Cr(100){sub bcc} underlayers grown hetero-epitaxially on MgO single-crystal substrates by ultra-high vacuum rf magnetron sputtering. The film growth behavior and the crystallographic properties are studied by reflection high energy electron diffraction and pole figure X-ray diffraction. Metastable hcp-NiFe(11-bar 00) and hcp-NiFe(112-bar 0) crystals respectively nucleate on Cr(211){sub bcc} and Cr(100){sub bcc} underlayers, where the hcp-NiFe crystals are stabilized through hetero-epitaxial growth. The hcp-NiFe(11-bar 00) crystal is a single-crystal with the c-axis parallel to the substrate surface, whereas the hcp-NiFe(112-bar 0) crystal is a bi-crystal with the respective c-axes lying in plane and perpendicular each other. With increasing the film thickness, the hcp structure in the NiFe films starts to transform into more stable fcc structure by atomic displacement parallel to the hcp(0001) close packed plane. The resulting films consist of hcp and fcc crystals.

NiFe epitaxial films with hcp and fcc structures prepared on bcc-Cr underlayers

International Nuclear Information System (INIS)

Higuchi, Jumpei; Ohtake, Mitsuru; Sato, Yoichi; Kirino, Fumiyoshi; Futamoto, Masaaki

2011-01-01

NiFe epitaxial films are prepared on Cr(211) bcc and Cr(100) bcc underlayers grown hetero-epitaxially on MgO single-crystal substrates by ultra-high vacuum rf magnetron sputtering. The film growth behavior and the crystallographic properties are studied by reflection high energy electron diffraction and pole figure X-ray diffraction. Metastable hcp-NiFe(11-bar 00) and hcp-NiFe(112-bar 0) crystals respectively nucleate on Cr(211) bcc and Cr(100) bcc underlayers, where the hcp-NiFe crystals are stabilized through hetero-epitaxial growth. The hcp-NiFe(11-bar 00) crystal is a single-crystal with the c-axis parallel to the substrate surface, whereas the hcp-NiFe(112-bar 0) crystal is a bi-crystal with the respective c-axes lying in plane and perpendicular each other. With increasing the film thickness, the hcp structure in the NiFe films starts to transform into more stable fcc structure by atomic displacement parallel to the hcp(0001) close packed plane. The resulting films consist of hcp and fcc crystals.

Atomic vibration amplitudes in fcc and hcp 4He through x-ray diffraction measurements

International Nuclear Information System (INIS)

Venkataraman, C.T.; Simmons, R.O.

2003-01-01

Atomic vibration amplitudes in dense fcc and hcp 4 He crystals have been measured using synchrotron x rays from the dependence of integrated Bragg intensities up to wave vectors of 91 nm -1 . Observed raw Bragg x-ray integrated intensities cover an extraordinary range, greater than 10 5 , due to the combined effect of the Debye-Waller factor and electronic form factor. From analysis of these intensities mean-square atomic vibration amplitudes Q 2 > and Lindemann ratios are determined. Path-integral Monte Carlo (PIMC) computations of Draeger and Ceperley, extrapolated to the thermodynamic limit, provide excellent agreement with these experimental results. For both present measurements and the PIMC results, one finds both a predominantly Gaussian distribution in Q 2 > and an extraordinarily large Lindemann ratio. In contrast, these directly measured x-ray values are significantly larger than published values inferred from Born-von Karman fitting to phonon dispersion measured by neutron scattering. Mildly anharmonic neon, which is fairly well described by self-consistent phonon theories, is contrasted with present results on fcc 4 He at corresponding densities

Lattice mechanical properties of some fcc f-shell metals

International Nuclear Information System (INIS)

Baria, J.K.; Jani, A.R.

2003-01-01

A pseudopotential depending on an effective core radius is proposed to study the binding energy, equation of state, ion-ion interaction, phonon dispersion curves (q-space and r-space analysis), mode Grueneisen parameters and dynamical elastic constants of some fcc f-shell metals La, Yb, Ce and Th. The contribution of the s-like electrons is calculated in the second-order perturbation theory for the potential while d- and f-like electron is taken into account by introducing repulsive short-range Born-Mayer term. The parameter of the potential is evaluated by zero pressure condition. An excellent agreement between theoretical investigations and experimental findings is achieved which confirms the present formalism. (author)

Effect of Steam Deactivation Severity of ZSM-5 Additives on LPG Olefins Production in the FCC Process.

Science.gov (United States)

Gusev, Andrey A; Psarras, Antonios C; Triantafyllidis, Konstantinos S; Lappas, Angelos A; Diddams, Paul A

2017-10-21

ZSM-5-containing catalytic additives are widely used in oil refineries to boost light olefin production and improve gasoline octanes in the Fluid Catalytic Cracking (FCC) process. Under the hydrothermal conditions present in the FCC regenerator (typically >700 °C and >8% steam), FCC catalysts and additives are subject to deactivation. Zeolites (e.g., Rare Earth USY in the base catalyst and ZSM-5 in Olefins boosting additives) are prone to dealumination and partial structural collapse, thereby losing activity, micropore surface area, and undergoing changes in selectivity. Fresh catalyst and additives are added at appropriate respective levels to the FCC unit on a daily basis to maintain overall targeted steady-state (equilibrated) activity and selectivity. To mimic this process under accelerated laboratory conditions, a commercial P/ZSM-5 additive was hydrothermally equilibrated via a steaming process at two temperatures: 788 °C and 815 °C to simulate moderate and more severe equilibration industrial conditions, respectively. n -Dodecane was used as probe molecule and feed for micro-activity cracking testing at 560 °C to determine the activity and product selectivity of fresh and equilibrated P-doped ZSM-5 additives. The fresh/calcined P/ZSM-5 additive was very active in C 12 cracking while steaming limited its activity, i.e., at catalyst-to-feed (C/F) ratio of 1, about 70% and 30% conversion was obtained with the fresh and steamed additives, respectively. A greater activity drop was observed upon increasing the hydrothermal deactivation severity due to gradual decrease of total acidity and microporosity of the additives. However, this change in severity did not result in any selectivity changes for the LPG (liquefied petroleum gas) olefins as the nature (Brønsted-to-Lewis ratio) of the acid/active sites was not significantly altered upon steaming. Steam deactivation of ZSM-5 had also no significant effect on aromatics formation which was enhanced at higher

Effect of Steam Deactivation Severity of ZSM-5 Additives on LPG Olefins Production in the FCC Process

Directory of Open Access Journals (Sweden)

Andrey A. Gusev

2017-10-01

Full Text Available ZSM-5-containing catalytic additives are widely used in oil refineries to boost light olefin production and improve gasoline octanes in the Fluid Catalytic Cracking (FCC process. Under the hydrothermal conditions present in the FCC regenerator (typically >700 °C and >8% steam, FCC catalysts and additives are subject to deactivation. Zeolites (e.g., Rare Earth USY in the base catalyst and ZSM-5 in Olefins boosting additives are prone to dealumination and partial structural collapse, thereby losing activity, micropore surface area, and undergoing changes in selectivity. Fresh catalyst and additives are added at appropriate respective levels to the FCC unit on a daily basis to maintain overall targeted steady-state (equilibrated activity and selectivity. To mimic this process under accelerated laboratory conditions, a commercial P/ZSM-5 additive was hydrothermally equilibrated via a steaming process at two temperatures: 788 °C and 815 °C to simulate moderate and more severe equilibration industrial conditions, respectively. n-Dodecane was used as probe molecule and feed for micro-activity cracking testing at 560 °C to determine the activity and product selectivity of fresh and equilibrated P-doped ZSM-5 additives. The fresh/calcined P/ZSM-5 additive was very active in C12 cracking while steaming limited its activity, i.e., at catalyst-to-feed (C/F ratio of 1, about 70% and 30% conversion was obtained with the fresh and steamed additives, respectively. A greater activity drop was observed upon increasing the hydrothermal deactivation severity due to gradual decrease of total acidity and microporosity of the additives. However, this change in severity did not result in any selectivity changes for the LPG (liquefied petroleum gas olefins as the nature (Brønsted-to-Lewis ratio of the acid/active sites was not significantly altered upon steaming. Steam deactivation of ZSM-5 had also no significant effect on aromatics formation which was enhanced at

Curie temperatures of fcc and bcc Nickel and Permalloy: Supercell and Green's function methods

Czech Academy of Sciences Publication Activity Database

Yu, P.; Jin, X.F.; Kudrnovský, Josef; Wang, D. S.; Bruno, P.

2008-01-01

Roč. 77, č. 5 (2008), 054431/1-054431/8 ISSN 1098-0121 R&D Projects: GA MŠk OC 150; GA AV ČR IAA100100616 Institutional research plan: CEZ:AV0Z10100520 Keywords : fcc - and bcc-Ni * Permalloy * magnetic moments * Curie temperatures Subject RIV: BE - Theoretical Physics Impact factor: 3.322, year: 2008

Pore Scale Thermal Hydraulics Investigations of Molten Salt Cooled Pebble Bed High Temperature Reactor with BCC and FCC Configurations

Directory of Open Access Journals (Sweden)

Shixiong Song

2014-01-01

CFD results and empirical correlations’ predictions of pressure drop and local Nusselt numbers. Local pebble surface temperature distributions in several default conditions are investigated. Thermal removal capacities of molten salt are confirmed in the case of nominal condition; the pebble surface temperature under the condition of local power distortion shows the tolerance of pebble in extreme neutron dose exposure. The numerical experiments of local pebble insufficient cooling indicate that in the molten salt cooled pebble bed reactor, the pebble surface temperature is not very sensitive to loss of partial coolant. The methods and results of this paper would be useful for optimum designs and safety analysis of molten salt cooled pebble bed reactors.

Identifying self-interstitials of bcc and fcc crystals in molecular dynamics

Science.gov (United States)

Bukkuru, S.; Bhardwaj, U.; Warrier, M.; Rao, A. D. P.; Valsakumar, M. C.

2017-02-01

Identification of self-interstitials in molecular dynamics (MD) simulations is of critical importance. There exist several criteria for identifying the self-interstitial. Most of the existing methods use an assumed cut-off value for the displacement of an atom from its lattice position to identify the self-interstitial. The results obtained are affected by the chosen cut-off value. Moreover, these chosen cut-off values are independent of temperature. We have developed a novel unsupervised learning algorithm called Max-Space Clustering (MSC) to identify an appropriate cut-off value and its dependence on temperature. This method is compared with some widely used methods such as effective sphere (ES) method and nearest neighbor sphere (NNS) method. The cut-off radius obtained using our method shows a linear variation with temperature. The value of cut-off radius and its temperature dependence is derived for five bcc (Cr, Fe, Mo, Nb, W) and six fcc (Ag, Au, Cu, Ni, Pd, Pt) crystals. It is seen that the ratio of the cut-off values "r" to the lattice constant "a" lies between 0.23 and 0.3 at 300 K and this ratio is on an average smaller for the fcc crystals. Collision cascade simulations are carried out for Primary knock-on Atom (PKA) energies of 5 keV in Fe (at 300 K and 1000 K) and W (at 300 K and 2500 K) and the results are compared using the various methods.

Use of riser tube rotation equipment in the Emlichheim and Landau petroleum mines of Wintershall AG Erdoelwerke; Einsatz von Steigrohrdrehvorrichtungen in den Erdoelfoerderbetrieben Emlichheim und Landau der Wintershall AG Erdoelwerke

Energy Technology Data Exchange (ETDEWEB)

Caspari, R. [Wintershall AG Erdoelwerke, Emlichheim (Germany)

1998-12-31

Riser tube rotation equipment has been in use in the Emlichheim and Landau petroleum wells since 1994 in order to ensure longer life of the riser tubes. (orig.) [Deutsch] In den von Wintershall operierten Erdoelfoerderbetrieben Emlichheim und Landau werden ca. 90% der Bohrungen mit Gestaengetiefpumpen gefoerdert. Aufgrund der lagerstaettentechnischen Gegebenheiten, der Thermalmassnahmen in Emlichheim und der Infrastruktur der Betriebe koennen andere Foerderhilfsmittel wie Tauchkreiselpumpe, Excenterschneckenpumpe oder Gasliften nur bedingt zum Einsatz kommen. Ein wesentlicher Faktor fuer den wirtschaftlichen Betrieb dieser Bohrungen sind die Aufwaeltigungen zur Beseitigung von Schaeden an der Tiefpumpe, dem Pumpgestaenge und den Steigrohren. Waehrend die Einsatzdauer der Tiefpumpen und des Pumpgestaenges durch hoeherwertige Materialguete und geeignete Optimierungsmassnahmen erhoeht werden konnten, sind die Standzeiten der Steigrohre nahezu unveraendert geblieben. Um diese zu erhoehen, werden in den Erdoelfoerderbetrieben Emlichheim und Landau seit April 1994 Steigrohrdrehvorrichtungen eingesetzt. (orig.)

Physics perspectives for a Future Circular Collider: FCC-hh/eh - Physics-Perspectives

CERN Multimedia

CERN. Geneva

2017-01-01

The lectures will briefly discuss the parameters of a Future Circular Collider, before addressing in detail the physics perspectives and the challenges for the experiments and detector systems. The main focus will be on ee and pp collisions, but opportunities for e—p physics will also be covered. The FCC physics perspectives will be presented with reference to the ongoing LHC programme, including the physics potential from future upgrades to the LHC in luminosity and possibly energy.

Fluidization behavior in a circulating slugging fluidized bed reactor. Part I : residence time and residence time distribution of polyethylene solids

NARCIS (Netherlands)

Putten, van I.C.; Sint Annaland, van M.; Weickert, G.

2007-01-01

Square nosed slugging fluidization behavior in a circulating fluidized bed riser using a polyethylene powder with a very wide particle size distribution was studied. In square nosed slugging fluidization the extent of mixing of particles of different size depends on the riser diameter, gas velocity,

Fluidization behavior in a circulating slugging fluidized bed reactor. Part I: Residence time and residence time distribution of polyethylene solids

NARCIS (Netherlands)

van Putten, I.C.; van Sint Annaland, M.; Weickert, G.

2007-01-01

Square nosed slugging fluidization behavior in a circulating fluidized bed riser using a polyethylene powder with a very wide particle size distribution was studied. In square nosed slugging fluidization the extent of mixing of particles of different size depends on the riser diameter, gas velocity,

A study of thermal-hydraulic requirements for increasing the power rates for natural-circulation boiling water reactors

International Nuclear Information System (INIS)

Yasuo, A.; Inada, F.; Hidaka, M.

1992-01-01

In this paper, the feasibility of higher power rates for natural-circulation boiling water reactors (BWRs) is studied with the objective of examining the flexibility of the plant power rate in constructing such plants to cope with the increasing demand for electricity. By applying existing one-dimensional design codes, the riser heights necessary to meet two major thermal-hydraulic requirements, i.e., critical power and core stability, are systematically calculated. Several restrictions on the maximum diameter and height of the pressure vessel are also considered because these restrictions could make construction impossible or drastically increase the construction costs. A very simple map of the dominant parameters for higher power rates is obtained. It is concluded that natural-circulation BWRs of >1000 MW (electric) will be feasible within the restrictions considered here

Interfacial morphologies and growth modes of F.C.C. metallic crystals from liquid alloys

International Nuclear Information System (INIS)

Camel, Denis

1980-01-01

Equilibrium and growth morphologies of f.c.c. metallic crystals in contact with liquid alloys have been observed in-situ using transmission electron microscopy. These morphologies have been discussed in terms of atomic interfacial structure and growth mechanisms with the help of a statistical thermodynamic model which takes into account the effects of chemical interactions and interfacial adsorption. (author) [fr

The FCC process as a producer of light olefins

International Nuclear Information System (INIS)

Yung, K.Y.; Yanik, S.; O'Connor, P.; Pouwels, C.

1992-01-01

To reduce emissions from the gasoline engine, aromatics content and vapor pressure of the motor gasoline pool will be reduced and a minimum amount of oxygen will be mandated. This reformulation will limit the application of high octane components like benzene, toluene and butanes and will require the use of oxygenates. To compensate for the loss in octane, the use of alkylate and, of course also oxygenates will grow. The Fluid Catalytic Cracking Unit is, as producer of (olefinic) propanes, butanes and pentanes, an important feedstock producer for alkylate and oxygenate producing process. Hence, process adjustments and FCC catalyst formations to increase the yield of above desirable light products are of prime importance and will be dealt with in this paper

Adaption of the LHC cold mass cooling system to the requirements of the Future Circular Collider (FCC)

Science.gov (United States)

Kotnig, C.; Tavian, L.; Brenn, G.

2017-12-01

The cooling of the superconducting magnet cold masses with superfluid helium (He II) is a well-established concept successfully in operation for years in the LHC. Consequently, its application for the cooling of FCC magnets is an obvious option. The 12-kW heat loads distributed over 10-km long sectors not only require an adaption of the magnet bayonet heat exchangers but also present new challenges to the cryogenic plants, the distribution system and the control strategy. This paper recalls the basic LHC cooling concept with superfluid helium and defines the main parameters for the adaption to the FCC requirements. Pressure drop and hydrostatic head are developed in the distribution and pumping systems; their impact on the magnet temperature profile and the corresponding cooling efficiency is presented and compared for different distribution and pumping schemes.

Bonding properties of FCC-like Au ₄₄ (SR) ₂₈ clusters from X-ray absorption spectroscopy

Energy Technology Data Exchange (ETDEWEB)

Yang, Rui [Department of Chemistry, Dalhousie University, Halifax, NS B3H 4R2, Canada.; Chevrier, Daniel M. [Department of Chemistry, Dalhousie University, Halifax, NS B3H 4R2, Canada.; Zeng, Chenjie [Department of Chemistry, Carnegie Mellon University, Pittsburgh, PA 15213, USA.; Jin, Rongchao [Department of Chemistry, Carnegie Mellon University, Pittsburgh, PA 15213, USA.; Zhang, Peng [Department of Chemistry, Dalhousie University, Halifax, NS B3H 4R2, Canada.

2017-11-01

Thiolate-protected gold clusters with precisely controlled atomic composition have recently emerged as promising candidates for a variety of applications because of their unique optical, electronic, and catalytic properties. The recent discovery of the Au44(SR)28 total structure is considered as an interesting finding in terms of the face-centered cubic (FCC)-like core structure in small gold-thiolate clusters. Herein, the unique bonding properties of Au44(SR)28 is analyzed using temperature-dependent X-ray absorption spectroscopy (XAS) measurements at the Au L3-edge and compared with other FCC-like clusters such as Au36(SR)24 and Au28(SR)20. A negative thermal expansion was detected for the Au–Au bonds of the metal core (the first Au–Au shell) and was interpreted based on the unique Au core structure consisting of the Au4 units. EXAFS fitting results from Au28(SR)20, Au36(SR)24, and Au44(SR)28 show a size-dependent negative thermal expansion behavior in the first Au–Au shell, further highlighting the importance of the Au4 units in determining the Au core bonding properties and shedding light on the growth mechanism of these FCC-like Au clusters.

Microstructure-sensitive modelling of dislocation creep in polycrystalline FCC alloys: Orowan theory revisited

Energy Technology Data Exchange (ETDEWEB)

Galindo-Nava, E.I., E-mail: eg375@cam.ac.uk; Rae, C.M.F.

2016-01-10

A new approach for modelling dislocation creep during primary and secondary creep in FCC metals is proposed. The Orowan equation and dislocation behaviour at the grain scale are revisited to include the effects of different microstructures such as the grain size and solute atoms. Dislocation activity is proposed to follow a jog-diffusion law. It is shown that the activation energy for cross-slip E{sub cs} controls dislocation mobility and the strain increments during secondary creep. This is confirmed by successfully comparing E{sub cs} with the experimentally determined activation energy during secondary creep in 5 FCC metals. It is shown that the inverse relationship between the grain size and dislocation creep is attributed to the higher number of strain increments at the grain level dominating their magnitude as the grain size decreases. An alternative approach describing solid solution strengthening effects in nickel alloys is presented, where the dislocation mobility is reduced by dislocation pinning around solute atoms. An analysis on the solid solution strengthening effects of typical elements employed in Ni-base superalloys is also discussed. The model results are validated against measurements of Cu, Ni, Ti and 4 Ni-base alloys for wide deformation conditions and different grain sizes.

Lattice design and beam optics calculations for the new large-scale electron-positron collider FCC-ee

CERN Document Server

Haerer, Bastian; Prof. Dr. Schmidt, Ruediger; Dr. Holzer, Bernhard

Following the recommendations of the European Strategy Group for High Energy Physics, CERN launched the Future Circular Collider Study (FCC) to investigate the feasibility of large-scale circular colliders for future high energy physics research. This thesis presents the considerations taken into account during the design process of the magnetic lattice in the arc sections of the electron-positron version FCC-ee. The machine is foreseen to operate at four different centre-of-mass energies in the range of 90 to 350 GeV. Different beam parameters need to be achieved for every energy, which requires a flexible lattice design in the arc sections. Therefore methods to tune the horizontal beam emittance without re-positioning machine components are implemented. In combination with damping and excitation wigglers a precise adjustment of the emittance can be achieved. A very first estimation of the vertical emittance arising from lattice imperfections is performed. Special emphasis is put on the optimisation of the ...

Preliminary Design Study of a Pre-booster Damping Ring for the FCC e+e− Injector

CERN Document Server

Etisken, O; Papaphilippou, Y

2017-01-01

The aim of the FCC e+e− lepton collider is to collide particles in the energy range 40–175 GeV. The FCC e+e− injector complex needs to produce and transport high-intensity e+e− beams at a fast repetition rate of about 0.1 Hz to top up the collider at its collision energy. A basic parameter set exists for all collider energies, assuming a 10 GeV linac operating with a large number of bunches accumulating in the existing SPS, which serves as pre-accelerator and damping ring before the bunches are transferred to the high-energy booster. The purpose of this study is to provide the conceptual design of an alternative damping and accelerator ring, replacing the SPS in the current scheme. This ring will have an injection energy of around 6 GeV and an extraction energy of around 20 GeV. Apart from establishing the basic ring parameters, the final study will include the optics design and layout, and single particle linear and non-linear dynamics optimization, including magnetic and alignment error tolerances. ...

Thermohydraulic simulation of HTR-10 nuclear reactor core using realistic CFD approach

International Nuclear Information System (INIS)

Silva, Alexandro S.; Dominguez, Dany S.; Mazaira, Leorlen Y. Rojas; Hernandez, Carlos R.G.; Lira, Carlos Alberto Brayner de Oliveira

2015-01-01

High-temperature gas-cooled reactors (HTGRs) have the potential to be used as possible energy generation sources in the near future, owing to their inherently safe performance by using a large amount of graphite, low power density design, and high conversion efficiency. However, safety is the most important issue for its commercialization in nuclear energy industry. It is very important for safety design and operation of an HTGR to investigate its thermal–hydraulic characteristics. In this article, it was performed the thermal–hydraulic simulation of compressible flow inside the core of the pebble bed reactor HTR (High Temperature Reactor)-10 using Computational Fluid Dynamics (CFD). The realistic approach was used, where every closely packed pebble is realistically modelled considering a graphite layer and sphere of fuel. Due to the high computational cost is impossible simulate the full core; therefore, the geometry used is a column of FCC (Face Centered Cubic) cells, with 41 layers and 82 pebbles. The input data used were taken from the thermohydraulic IAEA Benchmark (TECDOC-1694). The results show the profiles of velocity and temperature of the coolant in the core, and the temperature distribution inside the pebbles. The maximum temperatures in the pebbles do not exceed the allowable limit for this type of nuclear fuel. (author)

Catalytic cracking of vacuum gasoil overSVR, ITH, and MFI zeolites as FCC catalyst additives

Czech Academy of Sciences Publication Activity Database

Hussain, A. I.; Palani, A.; Aitani, A. M.; Čejka, Jiří; Shamzhy, Mariya; Kubů, Martin; Al-Khattaf, S. S.

2017-01-01

Roč. 161, JUN 2017 (2017), s. 23-32 ISSN 0378-3820 R&D Projects: GA ČR GBP106/12/G015; GA ČR(CZ) GP14-30898P Institutional support: RVO:61388955 Keywords : ith * mfi * Light olefins * FCC additives Subject RIV: CF - Physical ; Theoretical Chemistry OBOR OECD: Physical chemistry Impact factor: 3.752, year: 2016

Effect of flow on corrosion in catenary risers and its corrosion inhibitor performance

Energy Technology Data Exchange (ETDEWEB)

Ferreira, Pedro Altoe; Magalhaes, Alvaro Augusto Oliveira; Silva, Jussara de Mello [PETROBRAS S.A., Rio de Janeiro, RJ (Brazil); Kang, Cheolho; More, Parimal P. [Det Norske Veritas (DNV), Oslo (Norway)

2009-07-01

In oil and gas production, multiphase flow is often encountered and a range of different flow patterns can be experienced in pipelines. The flow regime transition and flow characteristics can be changed with the change of pipeline topography, which affects the corrosion and the performance of corrosion inhibitor in these multiphase pipelines. This paper outlines on the effect of inclination on the flow characteristics and their subsequent effect on corrosion rates. Also, this paper presents on the performance of three candidate corrosion inhibitors under severe slugging conditions at low water cut. For the simulation of offshore flow lines and risers, the experiments were carried out in a 44 m long, 10 cm diameter, three different pipeline inclinations of 0, 3 and 45 degrees. Light condensate oil with a viscosity of 2.5 cP at room temperature was used and water cut was 20%. The results indicated that the baseline corrosion rate in 45 degrees showed higher than other inclinations. Each corrosion inhibitor showed a different inhibitor performance. (author)

Estudio de la hidratación de pastas de cemento adicionadas con catalizador de craqueo catalítico usado (FCC de una refinería colombiana

Directory of Open Access Journals (Sweden)

Jenny Johanna Trochez

2010-01-01

Full Text Available En este artículo se analiza el efecto de la incorporación de un residuo industrial de una refinería de petróleo colombiana, conocido como catalizador de craqueo catalítico usado (FCC, en el proceso de hidratación de pastas cementicias. Para tal efecto, se prepararon pastas de cemento Pórtland ordinario (OPC adicionadas en porcentajes del 10 y 20% de FCC como reemplazo de la cantidad de cemento. La reactividad puzolánica del material y el tipo de productos de hidratación se determinó mediante difracción de rayos X (DRX y análisis termogravimétrico (TG/DTG. Adicionalmente, se determinó el calor de hidratación liberado con base en la norma ASTM C186. Los resultados indican que el proceso de hidratación de pastas adicionadas con FCC es altamente exotérmico como consecuencia de su actividad puzolánica a cortas edades. Las fases principales presentes en el proceso de hidratación de las pastas adicionadas con FCC fueron CSH, CAH y CASH, productos similares a los obtenidos en pastas adicionadas con metacaolín.

Determination of concentration distribution and velocity of a catalyst in a model of a fluidized bed reactor using nuclear techniques

International Nuclear Information System (INIS)

Santos, V.A. dos.

1981-09-01

A simplified model of a cracking unit was construct. The gaseous phase consisted of air, the solid phase (zeolite catalyst cracking) and both the phases circulate at the ambiente temperature in the steady state with 500 g of catalyst and air flow of 1600 1/h. Measurements for the circulation time of the solid phase (catalyst), concentration and radial distribution of catalyst have been carried out. The reduced experimental model of the cracking reactor (FCC) was used and radioctive tracer and attenuation of γ-radiation techniques were employed. (E.G.) [pt

A three-dimensional simulation of gas/particle flow and ozone decomposition in the riser of a circulating fluidized bed

DEFF Research Database (Denmark)

Hansen, Kim Granly; Solberg, Tron; Hjertager, Bjørn Helge

2004-01-01

The isothermal decomposition of ozone has been implemented in the CFD code FLOTRACS-MP-3D. The code is a 3D multiphase computational fluid dynamics code with an Eulerian description of both gas and particle phase. The turbulent motion of the particulate phase is modeled using the kinetic theory...... for granular flow, and the gas phase turbulence is modeled using a Sub-Grid-Scale model, cf. Ibsen et al. (2001). The decomposition reaction is studied in a 3D representation of a 0.254 m i.d. riser, which has been studied experimentally by Ouyang et al. (1993). The authors obtained profiles of ozone...

78 FR 23563 - FCC Reduces Backlog of Broadcast Indecency Complaints by 70% (More Than One Million Complaints...

Science.gov (United States)

2013-04-19

... Electronic Document Management System (EDOCS) at http://hraunfoss.fcc.gov/edocs_public/ . Alternative formats... may be filed using the Commission's Electronic Comment Filing System (ECFS). See Electronic Filing of Documents in Rulemaking Proceedings, 63 FR 24121 (1998). [ssquf] Electronic Filers: Comments may be filed...

Determination of the catalyst velocity profile along the riser of a fluidized bed reactor model by nuclear techniques

International Nuclear Information System (INIS)

Santos, V.A. dos; Dantas, C.C.

1982-01-01

A method adequated to industrial applications of flow measurements in fuidized bed reactor was developed. To measure the medium velocity of a catalyst, where the velocity is low, a radioactive tracer was used, 59 Fe and, to measure density by gamma attenuation, a standard source of 241 Am was used. The signals produced in NaI (Tl) scintilators detectors, were sent simultaneously to an electronic clock, to register the transit time, in the medium velocity measure of the catalyst whose reproductibility was 0.4%. The total estimated error for the method was a maximum of 4%. Important simplifications and pratical advantages are presented, if the method is compared to conventional measures with tracers. (E.G.) [pt

Catalytic cracking of Arabian Light VGO over novel zeolites as FCC catalyst additives for maximizing propylene yield

Czech Academy of Sciences Publication Activity Database

Hussain, A. I.; Aitani, A.; Kubů, Martin; Čejka, Jiří; Al-Khattaf, S.

2016-01-01

Roč. 167, MAR 2016 (2016), s. 226-239 ISSN 0016-2361 R&D Projects: GA ČR GBP106/12/G015 Institutional support: RVO:61388955 Keywords : catalytic cracking * FCC additives * 10-ring zeolites Subject RIV: CF - Physical ; Theoretical Chemistry Impact factor: 4.601, year: 2016

On the fabricability of a composite material containing the FCC matrix with embedded ductile B2 intermetallics

International Nuclear Information System (INIS)

Hosseinifar, Mehdi; Malakhov, Dmitri V.

2010-01-01

An imaginary composite material containing a ductile Al-rich FCC matrix with embedded particles of ductile RMg intermetallics (R is a rare-earth metal) may possess high strength and formability thus making it suitable as a replacement for steel in automotive applications. Although different fabrications routes can be explored, a direct-chill casting is likely least expensive of them. A crucial question is whether it is possible to find such a composition of the ternary Al-R-Mg melt whose solidification would result in the desired Al/RMg structure. In order to answer the question, a thermodynamic model of the Al-La-Mg system was built using the CALPHAD method. The model, whose validity was demonstrated by calorimetric experiments, was then used to prove that the FCC + LaMg composite material could not be produced via casting. Similar properties of rare-earth metals suggest that the conclusion based on the analysis of the particular Al-La-Mg case, will likely remain valid for other rare-earth elements.

MicroED Structure of Au146(p-MBA)57 at Subatomic Resolution Reveals a Twinned FCC Cluster.

Science.gov (United States)

Vergara, Sandra; Lukes, Dylan A; Martynowycz, Michael W; Santiago, Ulises; Plascencia-Villa, Germán; Weiss, Simon C; de la Cruz, M Jason; Black, David M; Alvarez, Marcos M; López-Lozano, Xochitl; Barnes, Christopher O; Lin, Guowu; Weissker, Hans-Christian; Whetten, Robert L; Gonen, Tamir; Yacaman, Miguel Jose; Calero, Guillermo

2017-11-16

Solving the atomic structure of metallic clusters is fundamental to understanding their optical, electronic, and chemical properties. Herein we present the structure of the largest aqueous gold cluster, Au 146 (p-MBA) 57 (p-MBA: para-mercaptobenzoic acid), solved by electron micro-diffraction (MicroED) to subatomic resolution (0.85 Å) and by X-ray diffraction at atomic resolution (1.3 Å). The 146 gold atoms may be decomposed into two constituent sets consisting of 119 core and 27 peripheral atoms. The core atoms are organized in a twinned FCC structure, whereas the surface gold atoms follow a C 2 rotational symmetry about an axis bisecting the twinning plane. The protective layer of 57 p-MBAs fully encloses the cluster and comprises bridging, monomeric, and dimeric staple motifs. Au 146 (p-MBA) 57 is the largest cluster observed exhibiting a bulk-like FCC structure as well as the smallest gold particle exhibiting a stacking fault.

Probing Anomalous WW γ and WWZ Couplings with Polarized Electron Beam at the LHeC and FCC-Ep Collider

CERN Document Server

Turk Cakir, I; Tasci, A T; Cakir, O

2016-01-01

We study the anomalous WWγ and WWZ couplings by calculating total cross sections of two processes at the LHeC with electron beam energy Ee=140 GeV and the proton beam energy Ep=7 TeV, and at the FCC-ep collider with the polarized electron beam energy Ee=80 GeV and the proton beam energy Ep=50 TeV. At the LHeC with electron beam polarization, we obtain the results for the difference of upper and lower bounds as (0.975, 0.118) and (0.285, 0.009) for the anomalous (∆κγ, λγ) and (∆κz, λz) couplings, respectively. As for FCC-ep collider, these bounds are obtained as (1.101, 0.065) and (0.320, 0.002) at an integrated luminosity of Lint=100 fb-1.

Geometric factors in f.c.c. and b.c.c. metal-on-metal epitaxy

International Nuclear Information System (INIS)

Bruce, L.A.; Jaeger, H.

1978-01-01

Deposits of Ni, Au and Ag formed by condensing metal vapour in U.H.V. onto (001)W, held at a temperature Tsub(s) in the range 300K< Tsub(s)<1200 K, always form epitaxial layers. However, while Au and Ag form (001) epitaxial layers of f.c.c. single crystals, (001)d parallel to (001)s with, say, [110]d parallel to [010]s, Ni and Cu occur in two orthogonal domains, each characterized by an exclusive set of fault (or twin) planes. Within a fault plane, atoms are hexagonally close-packed and, within a domain, fault planes are normal to either [1-1-0]s or [1-10]s and a close-packed direction in the planes is normal to the substrate. The lateral stacking of the fault planes may range from random at low values of Tsub(s) to that of, say, (11-1-) planes in heavily faulted and/or twinned (110) epitaxed f.c.c. material, or of basal planes in (110) epitaxed h.c.p. material at high values of Tsub(s). The results are readily explained on the basis of a growth model developed for deposits of Ni and Cu on (001) Ag. (author)

Radiation Load Optimization in the Final Focus System of FCC-hh

CERN Document Server

Martin, Roman; Cerutti, Francesco; Tomás, Rogelio

2016-01-01

With a center-of-mass energy of up to 100 TeV, FCC-hh will produce highly energetic collision debris at the Interaction Point (IP). Protecting the final focus quadrupoles from this radiation is challenging, since the required amount of shielding placed inside the magnets will reduce the free aperture, thereby limiting the β^{*} reach and luminosity. Hence, radiation mitigation strategies that make best use of the available aperture are required. In this paper, we study the possibility to split the first quadrupole Q1 into two quadrupoles with individual apertures, in order to distribute the radiation load more evenly and reduce the peak dose.

Analytic equation of state for FCC C60 solid based on analytic mean-field potential approach

International Nuclear Information System (INIS)

Sun Jiuxun

2006-01-01

The analytic mean-field approach (AMFP) was applied to the FCC C60 solid. For the intermolecular forces the Girifalco potential has been utilized. The analytic expressions for the Helmholtz free energy, internal energy and equation of state have been derived. The numerical results of thermodynamic quantities are compared with the molecular dynamic (MD) simulations and the unsymmetrized self-consistent field approach (CUSF) in the literature. It is shown that our AMFP results are in good agreement with the MD data both at low and high temperatures. The results of CUSF are in accordance with the AMFP at low temperature, but at high temperature the difference becomes prominent. Especially the AMFP predicted that the FCC C60 solid is stable upto 2202 K, the spinodal temperature, in good agreement with 2320 K from the MD simulation. However, the CUST just gives 1916 K, a temperature evidently lower than the MD data. The AMFP qualifies as a useful approach that can reasonably consider the anharmonic effects at high temperature

First-principles calculations of bulk and interfacial thermodynamic properties for fcc-based Al-Sc alloys

International Nuclear Information System (INIS)

Asta, M.; Foiles, S.M.; Quong, A.A.

1998-01-01

The configurational thermodynamic properties of fcc-based Al-Sc alloys and coherent Al/Al 3 Sc interphase-boundary interfaces have been calculated from first principles. The computational approach used in this study combines the results of pseudopotential total-energy calculations with a cluster-expansion description of the alloy energetics. Bulk and interface configurational-thermodynamic properties are computed using a low-temperature-expansion technique. Calculated values of the {100} and {111} Al/Al 3 Sc interfacial energies at zero temperature are, respectively, 192 and 226mJ/m 2 . The temperature dependence of the calculated interfacial free energies is found to be very weak for {100} and more appreciable for {111} orientations; the primary effect of configurational disordering at finite temperature is to reduce the degree of crystallographic anisotropy associated with calculated interfacial free energies. The first-principles-computed solid-solubility limits for Sc in bulk fcc Al are found to be underestimated significantly in comparison with experimental measurements. It is argued that this discrepancy can be largely attributed to nonconfigurational contributions to the entropy which have been neglected in the present thermodynamic calculations. copyright 1998 The American Physical Society

Axens new HyC 10 technology optimized with FCC while processing bitumen from Western Canada

Energy Technology Data Exchange (ETDEWEB)

Wisdom, L.; Sardar, H.; Nocca, J.L. [Axens North America Inc., Houston, TX (United States); Morel, F. [Axens SA, Salindres (France)

2006-07-01

A low pressure mild hydroconversion (MHC) method was described. HyC Technology has been recently commercialized as a cost-effective way of integrating fluid catalytic cracking (FCC) pretreating at moderate pressures, while still meeting the current and projected future requirements for ultra low sulfur diesel fuel. MHC has a low-medium conversion with sufficient FCC feed throughput to maintain gasoline production along with optimized hydrogen consumption. The process was recently tested using Canadian bitumen at a United States PADD II refinery. Details of production processes, feed quality and cracking potential for Canadian bitumen were presented. Partially hydrotreated straight run diesel (HDT) techniques were also compared with the MHC method. It was noted that MHC converted diesel is more refractory than HDT converted diesel, and that HDT techniques remain more appropriate for a variety of feeds and in situations where there is a hydrogen deficiency. Plans are now in place to adjust MHC HyC technology towards current diesel specifications, as well as to ensure constant MHC conversion. Yields, diesel, and residue product quality data for the first commercial plant using the technology were presented, as well as feedstock design bases. refs., tabs., figs.

Nucleation of recrystallization at selected sites in deformed fcc metals

DEFF Research Database (Denmark)

Xu, Chaoling

The objective of this thesis is to explore nucleation of recrystallization at selected sites in selected face-centered-cubic (FCC) metals, namely cold rolled columnar-grained nickel and high purity aluminum further deformed by indenting. Various techniques, including, optical microscopy, electron...... backscattered diffraction (EBSD), electron channeling contrast (ECC) and synchrotron X-ray technique, differential-aperture X-ray microscopy (DAXM), were used to characterize the microstructures, to explore nucleation sites, orientation relationships between nuclei and deformed microstructures, and nucleation...... mechanisms. In the cold rolled nickel samples, the preference of triple junctions (TJs) and grain boundaries (GBs) as nucleation sites is observed. The majorities of the nuclei have the same orientations as the surrounding matrix or are twin-related to a surrounding deformed grain. Only a few nuclei...

Durabilidad de morteros adicionados con FCC expuestos a sulfato de magnesio y sulfato de sodio

Directory of Open Access Journals (Sweden)

S Izquierdo

Full Text Available En este trabajo se presenta un análisis del deterioro de morteros adicionados con 10 y 20% de un residuo de catalizador de craqueo catalítico (FCC en presencia de sulfato de sodio (Na2SO4 y sulfato de magnesio (MgSO4 al 5% (concentración de 50g/L. Como materiales de referencia se utilizaron cemento portland sin adición (Cem.Ref, adicionado con 10% metacaolin (Cem-10MK y con 10% de humo de sílice (Cem-10HS. Para evaluar el desempeño frente a sulfatos se utilizó la norma ASTM C1012, determinándose la expansión longitudinal y la pérdida de resistencia a la compresión hasta edad de 392 días de exposición. Adicionalmente se efectuó el análisis microestructural por medio de difracción de rayos X (DRX y microscopia electrónica de barrido (SEM, para identificar los productos generados. Los resultados indican que la resistencia residual de las mezclas adicionadas con 10 y 20% de FCC luego de 360 días de inmersión en la solución de Na2SO4 son un 18,5% superior al valor reportado por la mezcla patrón y un 55% y 39% superior con respecto al de las mezclas conteniendo 10% de MK y HS respectivamente. Los morteros FCC10% en presencia de Na2SO4 reportan pérdida de resistencia del orden del 10% e inmersos en MgSO4 del 38%, valores inferiores al resto de mezclas evaluadas. Cabe anotar, que el MgSO4 es una solución más agresiva que Na2SO4 para todas las mezclas evaluadas. Como productos de la reacción con los sulfatos se identificaron etringita y yeso.

Zn(II Removal from Wastewater by Electrocoagulation/Flotation Method using New Configuration of a Split-Plate Airlift Electrochemical Reactor

Directory of Open Access Journals (Sweden)

Saad H. Ammar

2018-01-01

Full Text Available In this paper, split-plate airlift electrochemical reactor as an apparatus with new configuration for wastewater treatment was provided. Two aluminum plates were fixed inside the reactor and present two functions; first it works as split plates for internal loop generation of the airlift system (the zone between the two plates acts as riser while the other two zones act as downcomer and second it works as two electrodes for electrocoagulation process. Simulated wastewater contaminated with zinc ions was used to test the performance of this apparatus for zinc removal by studying the effect of different experimental variables such as initial concentration of zinc (50-800 ppm, electrical current density (2.67-21.4 mA/cm2, initial pH (3-11, air flowrate (12-50 LPH, and implicitly the electrocoagulation time. The results have shown the applicability of this split-plate airlift reactor as electrocoagulation cell in the treatment of wastewater such as wastewater containing Zink ions. The Zink removal percent was shown to increase upon increasing the current density and the electrolysis time. Also best removal percent was achieved in the initial pH range between 7 and 9. The minimum electrocoagulation time required for removal of ≥ 90% of Zn(II decreases from 90 to 22 min when operating current density increases from 2.67 to 21.4 mA/cm2.

Possible origin of the discrepancy in Peierls stresses of fcc metals: First-principles simulations of dislocation mobility in aluminum

Science.gov (United States)

Shin, Ilgyou; Carter, Emily A.

2013-08-01

Dislocation motion governs the strength and ductility of metals, and the Peierls stress (σp) quantifies dislocation mobility. σp measurements carry substantial uncertainty in face-centered cubic (fcc) metals, and σp values can differ by up to two orders of magnitude. We perform first-principles simulations based on orbital-free density functional theory (OFDFT) to calculate the most accurate currently possible σp for the motion of (1)/(2)111 dislocations in fcc Al. We predict the σps of screw and edge dislocations (dissociated in their equilibrium state) to be 1.9×10-4G and 4.9×10-5G, respectively (G is the shear modulus). These values fall within the range of measurements from mechanical deformation tests (10-4-10-5G). OFDFT also finds a new metastable structure for a screw dislocation not seen in earlier simulations, in which a dislocation core on the glide plane does not dissociate into partials. The corresponding σp for this undissociated dislocation is predicted to be 1.1×10-2G, which agrees with typical Bordoni peak measurements (10-2-10-3G). The calculated σps for dissociated and undissociated screw dislocations differ by two orders of magnitude. The presence of undissociated, as well as dissociated, screw dislocations may resolve the decades-long mystery in fcc metals regarding the two orders of magnitude discrepancy in σp measurements.

FCC-hh final-focus for flat-beams: parameters and energy deposition studies

CERN Document Server

AUTHOR|(CDS)2081283; Cruz Alaniz, Emilia; Seryi, Andrei; Van Riesen-Haupt, Leon; Besana, Maria Ilaria

2017-01-01

The international Future Circular Collider (FCC) study comprises the study of a new scientific structure in a tunnel of 100 km. This will allow the installation of two accelerators, a 45.6–175 GeV lepton collider and a 100-TeV hadron collider. An optimized design of a final-focus system for the hadron collider is presented here. The new design is more compact and enables unequal ${\\beta}$$^{∗}$ in both planes, whose choice is justified here. This is followed by energy deposition studies, where the total dose in the magnets as a consequence of the collision debris is evaluated.

Strength of Dislocation Junctions in FCC-monocrystals with a [\\overline{1}11] Deformation Axis

Science.gov (United States)

Kurinnaya, R. I.; Zgolich, M. V.; Starenchenko, V. A.

2017-07-01

The paper examines all dislocation reactions implemented in FCC-monocrystals with axis deformation oriented in the [\\overline{1}11] direction. It identifies the fracture stresses of dislocation junctions depending on intersection geometry of the reacting dislocation loop segments. Estimates are produced for the full spectrum of reacting forest dislocations. The paper presents the statistical data of the research performed and identifies the share of long strong dislocation junctions capable of limiting the zone of dislocation shift.

Diffraction evidence for an FCC in equilibrium HCP transformation in ytterbium

International Nuclear Information System (INIS)

Kayser, F.X.

1971-04-01

X-ray powder patterns obtained from polycrystalline wires of high-purity Yb in several heat treated conditions have demonstrated (i) the existence of a martensitic transformation, β-Yb (fcc) reversible α-Yb(hcp) and (ii) that the hexagonal close-packed structure is the thermodynamically stable form of Yb at temperatures below approximately 270 0 K. Precision lattice parameters determined for both polymorphs at room temperature indicate the fractional volume change on the transformation to be 0.0091, a magnitude that is consistent with the belief that α-Yb is divalent. This can be regarded as a stacking fault transformation, and one wherein the preponderance of the volume change is accommodated by displacements normal to the habit plane

Study Of Boosted W-Jets And Higgs-Jets With the SiFCC Detector

Energy Technology Data Exchange (ETDEWEB)

Yu, Shin-Shan [Taiwan, Natl. Central U.; Chekanov, Sergei [Argonne; Gray, Lindsey [Fermilab; Kotwal, Ashutosh [Duke U.; Sen, Sourav [Duke U.; Tran, Nhan Viet [Fermilab

2016-11-04

We study the detector performance in the reconstruction of hadronically-decaying W bosons and Higgs bosons at very high energy proton colliders using a full GEANT4 simulation of the SiFCC detector. The W and Higgs bosons carry transverse momentum in the multi-TeV range, which results in collimated decay products that are reconstructed as a single jet. We present a measurement of the energy response and resolution of boosted W-jets and Higgs-jets and show the separation of two sub-jets within the boosted boson jet.

Ecuaciones constitutivas avanzadas para describir el comportamiento termoviscoplástico de metales FCC

OpenAIRE

Pereira Valadés, Daniel

2011-01-01

En este proyecto de fin de carrera se ha llevado a cabo el estudio y proposición de ecuaciones constitutivas avanzadas que permitan describir con exactitud el comportamiento termoviscoplástico de metales FCC. Este estudio es de vital importancia para entender el proceso que tiene lugar en estos metales bajo condiciones de carga dinámicas, siempre en deformación plástica. La utilidad del estudio reside en la gran cantidad de procesos industriales que se llevan a cabo con este tipo de solicitac...

Towards the conceptual design of the cryogenic system of the Future Circular Collider (FCC)

Science.gov (United States)

Chorowski, M.; Correia Rodrigues, H.; Delikaris, D.; Duda, P.; Haberstroh, C.; Holdener, F.; Klöppel, S.; Kotnig, C.; Millet, F.; Polinski, J.; Quack, H.; Tavian, L.

2017-12-01

Following the update of the European strategy in particle physics, CERN has undertaken an international study of possible future circular colliders beyond the LHC. The study considers several options for very high-energy hadron-hadron, electron-positron and hadron-electron colliders. From the cryogenics point of view, the most challenging option is the hadron-hadron collider (FCC-hh) for which the conceptual design of the cryogenic system is progressing. The FCC-hh cryogenic system will have to produce up to 120 kW at 1.8 K for the superconducting magnet cooling, 6 MW between 40 and 60 K for the beam-screen and thermal-shield cooling as well as 850 g/s between 40 and 290 K for the HTS current-lead cooling. The corresponding total entropic load represents about 1 MW equivalent at 4.5 K and this cryogenic system will be by far the largest ever designed. In addition, the total mass to be cooled down is about 250’000 t and an innovative cool-down process must be proposed. This paper will present the proposed cryogenic layout and architecture, the cooling principles of the main components, the corresponding cooling schemes, as well as the cryogenic plant arrangement and proposed process cycles. The corresponding required development plan for such challenging cryogenic system will be highlighted.

Application of reliability techniques to prioritize BWR [boiling water reactor] recirculation loop welds for in-service inspection

International Nuclear Information System (INIS)

Holman, G.S.

1989-12-01

In January 1988 the US Nuclear Regulatory Commission issued Generic Letter 88-01 together with NUREG-0313, Revision 2, ''Technical Report on Material Selection and Processing Guidelines for BWR Coolant Pressure Boundary Piping,'' to implement NRC long-range plans for addressing the problem of stress corrosion cracking in boiling water reactor piping. NUREG-0313 presents guidelines for categorizing BWR pipe welds according to their SCC condition (e.g., presence of known cracks, implementation of measures for mitigating SCC) as well as recommended inspection schedules (e.g., percentage of welds inspected, inspection frequency) for each weld category. NUREG-0313 does not, however, specify individual welds to be inspected. To address this issue, the Lawrence Livermore National Laboratory developed two recommended inspection samples for welds in a typical BWR recirculation loop. Using a probabilistic fracture mechanics model, LLNL prioritized loop welds on the basis of estimated leak probabilities. The results of this evaluation indicate that riser welds and bypass welds should be given priority attention over other welds. Larger-diameter welds as a group can be considered of secondary importance compared to riser and bypass welds. A ''blind'' comparison between the probability-based inspection samples and data from actual field inspections indicated that the probabilistic analysis generally captured the welds which the field inspections identified as warranting repair or replacement. Discrepancies between the field data and the analytic results can likely be attributed to simplifying assumptions made in the analysis. The overall agreement between analysis and field experience suggests that reliability techniques -- when combined with historical experience -- represent a sound technical basis on which to define meaningful weld inspection programs. 13 refs., 8 figs., 5 tabs

CFD simulation of CO_2 sorption on K_2CO_3 solid sorbent in novel high flux circulating-turbulent fluidized bed riser: Parametric statistical experimental design study

International Nuclear Information System (INIS)

Thummakul, Theeranan; Gidaspow, Dimitri; Piumsomboon, Pornpote; Chalermsinsuwan, Benjapon

2017-01-01

Highlights: • Circulating-turbulent fluidization was proved to be advantage on CO_2 sorption. • The novel regime was proven to capture CO_2 higher than the conventional regimes. • Uniform solid particle distribution was observed in the novel fluidization regime. • The system continuity had more effect in the system than the process system mixing. • Parametric experimental design analysis was studied to evaluate significant factor. - Abstract: In this study a high flux circulating-turbulent fluidized bed (CTFB) riser was confirmed to be advantageous for carbon dioxide (CO_2) sorption on a potassium carbonate solid sorbent. The effect of various parameters on the CO_2 removal level was evaluated using a statistical experimental design. The most appropriate fluidization regime was found to occur between the turbulent and fast fluidization regimes, which was shown to capture CO_2 more efficiently than conventional fluidization regimes. The highest CO_2 sorption level was 93.4% under optimized CTFB operating conditions. The important parameters for CO_2 capture were the inlet gas velocity and the interactions between the CO_2 concentration and the inlet gas velocity and water vapor concentration. The CTFB regime had a high and uniform solid particle distribution in both the axial and radial system directions and could transport the solid sorbent to the regeneration reactor. In addition, the process system continuity had a stronger effect on the CO_2 removal level in the system than the process system mixing.

Dislocation creation and void nucleation in FCC ductile metals under tensile loading: a general microscopic picture.

Science.gov (United States)

Pang, Wei-Wei; Zhang, Ping; Zhang, Guang-Cai; Xu, Ai-Guo; Zhao, Xian-Geng

2014-11-10

Numerous theoretical and experimental efforts have been paid to describe and understand the dislocation and void nucleation processes that are fundamental for dynamic fracture modeling of strained metals. To date an essential physical picture on the self-organized atomic collective motions during dislocation creation, as well as the essential mechanisms for the void nucleation obscured by the extreme diversity in structural configurations around the void nucleation core, is still severely lacking in literature. Here, we depict the origin of dislocation creation and void nucleation during uniaxial high strain rate tensile processes in face-centered-cubic (FCC) ductile metals. We find that the dislocations are created through three distinguished stages: (i) Flattened octahedral structures (FOSs) are randomly activated by thermal fluctuations; (ii) The double-layer defect clusters are formed by self-organized stacking of FOSs on the close-packed plane; (iii) The stacking faults are formed and the Shockley partial dislocations are created from the double-layer defect clusters. Whereas, the void nucleation is shown to follow a two-stage description. We demonstrate that our findings on the origin of dislocation creation and void nucleation are universal for a variety of FCC ductile metals with low stacking fault energies.

Effects of different level addition of zeolite ZSM-5 additive on quality and composition of the dry gas, LPG (Liquefied Petroleum Gas) and gasoline, produced in FCC (Fluid Catalytic Cracking); Efeito dos diferentes niveis de adicao de aditivos de ZSM-5 na qualidade e composicao do gas combustivel, GLP e gasolina produzidos em FCC

Energy Technology Data Exchange (ETDEWEB)

Bastiani, Raquel; Pimenta, Ricardo D.M.; Almeida, Marlon B.B.; Lau, Lam Y. [PETROBRAS S.A., Rio de Janeiro, RJ (Brazil)

2004-07-01

The effects of the addition of different level of ZSM-5 additives on different FCC catalysts formulations have been studied on laboratory scale FST (Fluidized Simulation Test). The main objective of the present work is to perform a qualitative identification of the main parameters of FCC catalyst which affect the ZSM-5 additives performance concerning quality and composition of Dry Gas, LPG and Gasoline. The product composition of each test was analyzed by PIANO groups separated by carbon number. The effect of ZSM-5 on products composition was evaluated. The results showed that the ZSM-5 additive cracks gasoline range olefins and isoparaffins into Dry Gas and LPG, favoring the formation of ethylene, propylene and butylenes, while the absolute yield of gasoline aromatics changes little. The aromatics fraction in gasoline, MON and RON numbers in gasoline increase. The ZSM-5 effectiveness is negatively affected by high levels of rare earth on FCC catalyst (RE-USY). Higher hydrogen transfer provides lower olefins (higher than C6) formation, which are the most reactive species for ZSM-5 cracking. (author)

Recent advances on thermohydraulic simulation of HTR-10 nuclear reactor core using realistic CFD approach

Energy Technology Data Exchange (ETDEWEB)

Silva, Alexandro S., E-mail: alexandrossilva@ifba.edu.br [Instituto Federal de Educacao, Ciencia e Tecnologia da Bahia (IFBA), Vitoria da Conquista, BA (Brazil); Mazaira, Leorlen Y.R., E-mail: leored1984@gmail.com, E-mail: cgh@instec.cu [Instituto Superior de Tecnologias y Ciencias Aplicadas (INSTEC), La Habana (Cuba); Dominguez, Dany S.; Hernandez, Carlos R.G., E-mail: alexandrossilva@gmail.com, E-mail: dsdominguez@gmail.com [Universidade Estadual de Santa Cruz (UESC), Ilheus, BA (Brazil). Programa de Pos-Graduacao em Modelagem Computacional; Lira, Carlos A.B.O., E-mail: cabol@ufpe.br [Universidade Federal de Pernambuco (UFPE), Recife, PE (Brazil)

2015-07-01

High-temperature gas-cooled reactors (HTGRs) have the potential to be used as possible energy generation sources in the near future, owing to their inherently safe performance by using a large amount of graphite, low power density design, and high conversion efficiency. However, safety is the most important issue for its commercialization in nuclear energy industry. It is very important for safety design and operation of an HTGR to investigate its thermal-hydraulic characteristics. In this article, it was performed the thermal-hydraulic simulation of compressible flow inside the core of the pebble bed reactor HTR (High Temperature Reactor)-10 using Computational Fluid Dynamics (CFD). The realistic approach was used, where every closely packed pebble is realistically modelled considering a graphite layer and sphere of fuel. Due to the high computational cost is impossible simulate the full core; therefore, the geometry used is a FCC (Face Centered Cubic) cell with the half height of the core, with 21 layers and 95 pebbles. The input data used were taken from the thermal-hydraulic IAEA Bechmark. The results show the profiles of velocity and temperature of the coolant in the core, and the temperature distribution inside the pebbles. The maximum temperatures in the pebbles do not exceed the allowable limit for this type of nuclear fuel. (author)

Recent advances on thermohydraulic simulation of HTR-10 nuclear reactor core using realistic CFD approach

International Nuclear Information System (INIS)

Silva, Alexandro S.; Mazaira, Leorlen Y.R.; Dominguez, Dany S.; Hernandez, Carlos R.G.

2015-01-01

High-temperature gas-cooled reactors (HTGRs) have the potential to be used as possible energy generation sources in the near future, owing to their inherently safe performance by using a large amount of graphite, low power density design, and high conversion efficiency. However, safety is the most important issue for its commercialization in nuclear energy industry. It is very important for safety design and operation of an HTGR to investigate its thermal-hydraulic characteristics. In this article, it was performed the thermal-hydraulic simulation of compressible flow inside the core of the pebble bed reactor HTR (High Temperature Reactor)-10 using Computational Fluid Dynamics (CFD). The realistic approach was used, where every closely packed pebble is realistically modelled considering a graphite layer and sphere of fuel. Due to the high computational cost is impossible simulate the full core; therefore, the geometry used is a FCC (Face Centered Cubic) cell with the half height of the core, with 21 layers and 95 pebbles. The input data used were taken from the thermal-hydraulic IAEA Bechmark. The results show the profiles of velocity and temperature of the coolant in the core, and the temperature distribution inside the pebbles. The maximum temperatures in the pebbles do not exceed the allowable limit for this type of nuclear fuel. (author)

A new approach to establish both stable and metastable phase equilibria for fcc ordered/disordered phase transition: application to the Al–Ni and Ni–Si systems

International Nuclear Information System (INIS)

Yuan Xiaoming; Zhang Lijun; Du Yong; Xiong Wei; Tang Ying; Wang Aijun; Liu Shuhong

2012-01-01

Both two-sublattice (2SL) and four-sublattice (4SL) models in the framework of the compound energy formalism can be used to describe the fcc ordered/disordered transitions. When transferring the parameters of 2SL disregarding the metastable ordered states into those of 4SL, inconsistence in either stable or metastable phase diagrams could appear, as detected in both Al–Ni and Ni–Si systems. To avoid such a kind of drawback, this behavior was analyzed and investigated in the Ni–Si and Al–Ni systems with the aid of first–principle calculations. Furthermore, a new approach considering both the stable and metastable fcc ordered phase equilibria deduced from the first–principles calculations was proposed to perform a reliable thermodynamic modeling for the fcc ordered/disordered transition. The Ni–Si system was then thermodynamically assessed using the presently proposed approach. The good agreement between the calculation and experiments demonstrates the reliability of the proposed approach. It is expected that the approach is valid for other systems showing complex ordered/disordered transitions. - Highlights: ► We discuss the drawbacks of order/disorder modeling in the Ni–Si and Al–Ni systems. ► We perform ab initio calculation of thermodynamic properties in the Ni–Si system. ► A CALPHAD–type approach is proposed to model the fcc ordered/disordered transition. ► The Ni–Si system was thermodynamically assessed using the new approach.

Betatron-collimation Studies for Heavy Ions in the FCC-hh

CERN Multimedia

Logothetis Agaliotis, Efstathios

2018-01-01

One of the biggest challenges in the design of the FCC-hh is the collimation system. From LHC experience it is known that a collimation system optimized for proton cleaning has a significantly reduced efficiency for heavy ions. The study presented in this contribution evaluates the betatron-collimation efficiency for the heavy-ion operation with lead nuclei at a beam energy of 50 Z TeV in the system designed for proton operation. The fragmentation processes of the main beam particles in the primary collimator are simulated with FLUKA and fragments are individually tracked with SixTrack until being lost in the downstream aperture. In this way a first-impact loss-map is obtained, identifying locations where high energy deposition are to be expected. This provides a first-level assessment of feasibility and allows to include countermeasures in the conceptual accelerator design.

Rayleigh oscillations localized near free surface of a fcc crystal

International Nuclear Information System (INIS)

Kosevich, A.M.; Matsokin, D.V.; Savotchenko, S.E.

1997-01-01

The waves, which are localized near the free (001) surface of a fcc crystal and propagate in the [110] direction, are described using the model of central interaction of the nearest neighbors. The frequencies of these waves come into the gaps within the frequency spectrum of bulk harmonic oscillations with a fixed wave vector k component along the surface. The long-wave limit and the case of wave vectors close to the Brillouin band boundary are studied analytically. These limit dependences are in agreement with other authors results which were obtained by numerical methods. Analytical calculations in the limit intervals of k are supplemented by numerical calculations for any values of the wave vector. It is essential that these waves have a displacement component which is perpendicular to the crystal surface and can, therefore, be studied by methods of He atoms inelastic scattering

The influence of anisotropy on the core structure of Shockley partial dislocations within FCC materials

Science.gov (United States)

Szajewski, B. A.; Hunter, A.; Luscher, D. J.; Beyerlein, I. J.

2018-01-01

Both theoretical and numerical models of dislocations often necessitate the assumption of elastic isotropy to retain analytical tractability in addition to reducing computational load. As dislocation based models evolve towards physically realistic material descriptions, the assumption of elastic isotropy becomes increasingly worthy of examination. We present an analytical dislocation model for calculating the full dissociated core structure of dislocations within anisotropic face centered cubic (FCC) crystals as a function of the degree of material elastic anisotropy, two misfit energy densities on the γ-surface ({γ }{{isf}}, {γ }{{usf}}) and the remaining elastic constants. Our solution is independent of any additional features of the γ-surface. Towards this pursuit, we first demonstrate that the dependence of the anisotropic elasticity tensor on the orientation of the dislocation line within the FCC crystalline lattice is small and may be reasonably neglected for typical materials. With this approximation, explicit analytic solutions for the anisotropic elasticity tensor {B} for both nominally edge and screw dislocations within an FCC crystalline lattice are devised, and employed towards defining a set of effective isotropic elastic constants which reproduce fully anisotropic results, however do not retain the bulk modulus. Conversely, Hill averaged elastic constants which both retain the bulk modulus and reasonably approximate the dislocation core structure are employed within subsequent numerical calculations. We examine a wide range of materials within this study, and the features of each partial dislocation core are sufficiently localized that application of discrete linear elasticity accurately describes the separation of each partial dislocation core. In addition, the local features (the partial dislocation core distribution) are well described by a Peierls-Nabarro dislocation model. We develop a model for the displacement profile which depends upon

In-situ transmission electron microscopy study of ion-irradiated copper : comparison of the temperature dependence of cascade collapse in FCC- and BCC- metals.

Energy Technology Data Exchange (ETDEWEB)

Daulton, T. L.

1998-10-23

The kinetics which drive cascade formation and subsequent collapse into point-defect clusters is investigated by analyzing the microstructure produced in situ by low fluence 100 keV Kr ion irradiations of fcc-Cu over a wide temperature range (18-873 K). The yield of collapsed point-defect clusters is demonstrated unequivocally to be temperature dependent, remaining approximately constant up to lattice temperatures of 573 K and then abruptly decreasing with increasing temperature. This drop in yield is not caused by defect loss during or following ion irradiation. This temperature dependence can be explained by a thermal spike effect. These in-situ yield measurements are compared to previous ex-situ yield measurements in fcc-Ni and bcc-Mo.

Atomic mobility in liquid and fcc Al-Si-Mg-RE (RE = Ce, Sc) alloys and its application to the simulation of solidification processes in RE-containing A357 alloys

Energy Technology Data Exchange (ETDEWEB)

Lu, Zhao; Zhang, Lijun [Central South Univ., Changsha (China). State Key Lab of Powder Metallurgy; Tang, Ying [Thermo-Calc Software AB, Solna (Sweden)

2017-06-15

This paper first provides a critical review of experimental and theoretically-predicted diffusivities in both liquid and fcc Al-Si-Mg-RE (RE = Ce, Sc) alloys as-reported by previous researchers. The modified Sutherland equation is then employed to predict self- and impurity diffusivities in Al-Si-Mg-RE melts. The self-diffusivity of metastable fcc Sc is evaluated via the first-principles computed activation energy and semi-empirical relations. Based on the critically-reviewed and presently evaluated diffusivity information, atomic mobility descriptions for liquid and fcc phases in the Al-Si-Mg-RE systems are established by means of the Diffusion-Controlled TRAnsformation (DICTRA) software package. Comprehensive comparisons show that most of the measured and theoretically-predicted diffusivities can be reasonably reproduced by the present atomic mobility descriptions. The atomic mobility descriptions for liquid and fcc Al-Si-Mg-RE alloys are further validated by comparing the model-predicted differential scanning calorimetry curves for RE-containing A357 alloys during solidification against experimental data. Detailed analysis of the curves and microstructures in RE-free and RE-containing A357 alloys indicates that both Ce and Sc can serve as the grain refiner for A357 alloys, and that the grain refinement efficiency of Sc is much higher.

Atomic mobility in liquid and fcc Al-Si-Mg-RE (RE = Ce, Sc) alloys and its application to the simulation of solidification processes in RE-containing A357 alloys

International Nuclear Information System (INIS)

Lu, Zhao; Zhang, Lijun

2017-01-01

This paper first provides a critical review of experimental and theoretically-predicted diffusivities in both liquid and fcc Al-Si-Mg-RE (RE = Ce, Sc) alloys as-reported by previous researchers. The modified Sutherland equation is then employed to predict self- and impurity diffusivities in Al-Si-Mg-RE melts. The self-diffusivity of metastable fcc Sc is evaluated via the first-principles computed activation energy and semi-empirical relations. Based on the critically-reviewed and presently evaluated diffusivity information, atomic mobility descriptions for liquid and fcc phases in the Al-Si-Mg-RE systems are established by means of the Diffusion-Controlled TRAnsformation (DICTRA) software package. Comprehensive comparisons show that most of the measured and theoretically-predicted diffusivities can be reasonably reproduced by the present atomic mobility descriptions. The atomic mobility descriptions for liquid and fcc Al-Si-Mg-RE alloys are further validated by comparing the model-predicted differential scanning calorimetry curves for RE-containing A357 alloys during solidification against experimental data. Detailed analysis of the curves and microstructures in RE-free and RE-containing A357 alloys indicates that both Ce and Sc can serve as the grain refiner for A357 alloys, and that the grain refinement efficiency of Sc is much higher.

Observations of a fcc helium gas-bubble superlattice in copper, nickel, and stainless steel

International Nuclear Information System (INIS)

Johnson, P.B.; Mazey, D.J.

1980-01-01

Transmission electron microscopy is used to investigate the spatial arrangement of the small gas bubbles produced in several fcc metals by 30 keV helium ion irradiation to high dose at 300 K. In what is a new result for this important class of metals it is found that the helium gas bubbles lie on a superlattice having an fcc structure with principal axes aligned with those of the metal matrix. The bubble lattice constant asub(i), is measured for a helium fluence just below the critical dose for radiation blistering of the metal surface (approximately 4 x 10 17 He/cm 2 ). Implantation rates are typically approximately 10 14 He ions cm -2 sec -1 . The values of asub(i) obtained for copper, nickel and stainless steel are (7.6 +- 0.3)nm, (6.6 +- 0.5)nm and (6.4 +- 0.5)nm respectively. Above the critical dose the bubble lattice is seen to survive in some blister caps as well as in the region between blisters. Bubble alignment is also observed in the case of hydrogen bubbles produced in copper by low energy proton irradiation to high fluence at 300 K. The presentation of this data was accompanied by a cine film illustrating the behaviour of the gas bubble lattice in copper during post-irradiation annealing in the electron microscope. A summary of the film is given in the appendix. (author)

A Three-Dimensional Numerical Study of Gas-Particle Flow and Chemical Reactions in Circulating Fluidised Bed Reactors

DEFF Research Database (Denmark)

Hansen, Kim Granly

Three-dimensional Computational Fluid Dynamics (CFD) simulations of Circulating Fluidized Beds (CFB's) have been performed. The computations are performed using a 3D multiphase computational fluid dynamics code with an Eulerian description of both gas and particle phases. The turbulent motion...... implemented in the CFD code FLOTRACS-MP-3D. The decomposition reaction is studied in a 3D representation of a 0.254 m i.d. riser, which has been studied experimentally by Ouyang et al. (1993). Comparison between measured and simulated time-averaged ozone concentration at different elevations in the riser...

Sensitivity study of the Hb$\\bar{b}$ and Hc$\\bar{c}$ couplings for e$^+$- e$^-$ collisions at FCC

CERN Document Server

Heckmann, Lea Alina

2017-01-01

The Future Circular Collider (FCC) is one of the possible future projects proposed at CERN. With a circumference of 80 - 100km it should initially serve as an e$^+$- e$^-$ collider reaching energies between 90 - 350 GeV. While operating at centre of mass energies of 240 GeV and luminosities of 5*10$^{34}$ cm$^{-2}$s$^{-1}$ FCC should be used as a Higgs factory with the aim of validating standard model predictions. Therefore, it should be able to measure the Higgs couplings with precisions around 1%. In order to estimate the sensitivity of the branching ratio for $H\\rightarrow c\\bar{c}$ (BR(Hcc)) a simultaneous simulation and analysis of Hb$\\bar{b}$ and Hc$\\bar{c}$ is necessary. Therefore, events were generated for both cases and afterwards the CMS detector with an added c-tagging method was used to simulate the detector response. Relevant events were selected and afterwards used for optimising a simultaneous fit determining BR(Hbb) and BR(Hcc) and its uncertainties. The same procedure was applied while chang...

Transalkylation of ethyl benzene with triethylbenzene over ZSM-5 zeolite catalyst

KAUST Repository

Akhtar, M. Naseem; Tukur, Nasiru M.; Al-Yassir, Nabil; Al-Khattaf, Sulaiman; Čejka, Jiří

2010-01-01

Transalkylation of 1,3,5-triethylbenzene (TEB) with ethylbenzene (EB) has been studied over ZSM-5 zeolite using a riser simulator reactor with respect to optimizing DEB yield. The reaction temperature was varied from 350 to 500°C with contact time

Microstructure and Mechanical Strengths of Metastable FCC Solid Solutions in Al-Ce-Fe System

OpenAIRE

A., Inoue; H., Yamaguchi; M., Kikuchi; T., Masumoto; Institute for Materials Research; Institute for Materials Research; Institute for Materials Research; Institute for Materials Research

1990-01-01

A metastable fcc solid solution (SS) with high mechanical strengths and good bending ductility was found to be formed in rapidly solidified Al-Ce-Fe alloys containing the solute elements below about 6 at%. The SS consists of equiaxed grains with a size of about 2μm and contains a high density of internal defects. The highest hardness (H_v) and tensile fracture strengtn (σ_f) are 440 and 860 MPa in the as-quenched state and remain almost unchanged up to about 600 K for 1 h, though fine compoun...

Epitaxial growth of fcc-CoxNi100-x thin films on MgO(110) single-crystal substrates

International Nuclear Information System (INIS)

Ohtake, Mitsuru; Nukaga, Yuri; Sato, Yoichi; Futamoto, Masaaki; Kirino, Fumiyoshi

2009-01-01

Co x Ni 100-x (x=100, 80, 20, 0 at. %) epitaxial thin films were prepared on MgO(110) single-crystal substrates heated at 300 deg. C by ultrahigh vacuum molecular beam epitaxy. The growth mechanism is discussed based on lattice strain and crystallographic defects. CoNi(110) single-crystal films with a fcc structure are obtained for all compositions. Co x Ni 100-x film growth follows the Volmer-Weber mode. X-ray diffraction analysis indicates that the out-of-plane and the in-plane lattice spacings of the Co x Ni 100-x films are in agreement within ±0.5% with the values of the respective bulk Co x Ni 100-x crystals, suggesting that the strain in the film is very small. High-resolution cross-sectional transmission microscopy shows that an atomically sharp boundary is formed between a Co(110) fcc film and a MgO(110) substrate, where periodical misfit dislocations are preferentially introduced in the film at the Co/MgO interface. The presence of such periodical misfit dislocations relieves the strain caused by the lattice mismatch between the film and the substrate.

Identifying self-interstitials of bcc and fcc crystals in molecular dynamics

International Nuclear Information System (INIS)

Bukkuru, S.; Bhardwaj, U.; Warrier, M.; Rao, A.D.P.; Valsakumar, M.C.

2017-01-01

Identification of self-interstitials in molecular dynamics (MD) simulations is of critical importance. There exist several criteria for identifying the self-interstitial. Most of the existing methods use an assumed cut-off value for the displacement of an atom from its lattice position to identify the self-interstitial. The results obtained are affected by the chosen cut-off value. Moreover, these chosen cut-off values are independent of temperature. We have developed a novel unsupervised learning algorithm called Max-Space Clustering (MSC) to identify an appropriate cut-off value and its dependence on temperature. This method is compared with some widely used methods such as effective sphere (ES) method and nearest neighbor sphere (NNS) method. The cut-off radius obtained using our method shows a linear variation with temperature. The value of cut-off radius and its temperature dependence is derived for five bcc (Cr, Fe, Mo, Nb, W) and six fcc (Ag, Au, Cu, Ni, Pd, Pt) crystals. It is seen that the ratio of the cut-off values “r” to the lattice constant “a” lies between 0.23 and 0.3 at 300 K and this ratio is on an average smaller for the fcc crystals. Collision cascade simulations are carried out for Primary knock-on Atom (PKA) energies of 5 keV in Fe (at 300 K and 1000 K) and W (at 300 K and 2500 K) and the results are compared using the various methods. - Highlights: • Max-Space Clustering (MSC) method is developed to identify interstitials in crystals. • MSC provides a structured way to identify the temperature dependent cut-off radius. • It is compared with widely used sphere methods and found to be better. • MSC coupled with graph tree optimization can be used to obtain diffusion trajectory. • Cascade simulations of Fe, W are carried out and results are compared with various methods.

Identifying self-interstitials of bcc and fcc crystals in molecular dynamics

Energy Technology Data Exchange (ETDEWEB)

Bukkuru, S., E-mail: srinivasaraobukkuru@gmail.com [Dept. of Nuclear Physics, Andhra University, Visakhapatnam 530003 (India); Bhardwaj, U., E-mail: haptork@gmail.com [Computational Analysis Division, BARC, Visakhapatnam 530012, Andhra Pradesh (India); Warrier, M., E-mail: manoj.warrier@gmail.com [Computational Analysis Division, BARC, Visakhapatnam 530012, Andhra Pradesh (India); Rao, A.D.P., E-mail: adp_rao_99@yahoo.com [Dept. of Nuclear Physics, Andhra University, Visakhapatnam 530003 (India); Valsakumar, M.C., E-mail: mc.valsakumar@gmail.com [IIT Palakkad, Kozhippara P.O., Palakkad 678557, Kerala (India)

2017-02-15

Identification of self-interstitials in molecular dynamics (MD) simulations is of critical importance. There exist several criteria for identifying the self-interstitial. Most of the existing methods use an assumed cut-off value for the displacement of an atom from its lattice position to identify the self-interstitial. The results obtained are affected by the chosen cut-off value. Moreover, these chosen cut-off values are independent of temperature. We have developed a novel unsupervised learning algorithm called Max-Space Clustering (MSC) to identify an appropriate cut-off value and its dependence on temperature. This method is compared with some widely used methods such as effective sphere (ES) method and nearest neighbor sphere (NNS) method. The cut-off radius obtained using our method shows a linear variation with temperature. The value of cut-off radius and its temperature dependence is derived for five bcc (Cr, Fe, Mo, Nb, W) and six fcc (Ag, Au, Cu, Ni, Pd, Pt) crystals. It is seen that the ratio of the cut-off values “r” to the lattice constant “a” lies between 0.23 and 0.3 at 300 K and this ratio is on an average smaller for the fcc crystals. Collision cascade simulations are carried out for Primary knock-on Atom (PKA) energies of 5 keV in Fe (at 300 K and 1000 K) and W (at 300 K and 2500 K) and the results are compared using the various methods. - Highlights: • Max-Space Clustering (MSC) method is developed to identify interstitials in crystals. • MSC provides a structured way to identify the temperature dependent cut-off radius. • It is compared with widely used sphere methods and found to be better. • MSC coupled with graph tree optimization can be used to obtain diffusion trajectory. • Cascade simulations of Fe, W are carried out and results are compared with various methods.

Calculation of the surface free energy of fcc copper nanoparticles

International Nuclear Information System (INIS)

Jia Ming; Lai Yanqing; Tian Zhongliang; Liu Yexiang

2009-01-01

Using molecular dynamics simulations with the modified analytic embedded-atom method we calculate the Gibbs free energy and surface free energy for fcc Cu bulk, and further obtain the Gibbs free energy of nanoparticles. Based on the Gibbs free energy of nanoparticles, we have investigated the heat capacity of copper nanoparticles. Calculation results indicate that the Gibbs free energy and the heat capacity of nanoparticles can be divided into two parts: bulk quantity and surface quantity. The molar heat capacity of the bulk sample is lower compared with the molar heat capacity of nanoparticles, and this difference increases with the decrease in the particle size. It is also observed that the size effect on the thermodynamic properties of Cu nanoparticles is not really significant until the particle is less than about 20 nm. It is the surface atoms that decide the size effect on the thermodynamic properties of nanoparticles

Localization in small fcc-particles with surface irregularities and disorder

International Nuclear Information System (INIS)

Bucher, J.P.; Bloomfield, L.A.

1991-01-01

A numerical eigenvector analysis is used to investigate Anderson localization in small fcc-particles of N = 309 and N = 147 atoms. Special attention is given to the way size and surface roughness of the particles influence the localization behavior. States begin to localize in a non-exponential regime several lattice spacings from the center of localization and finally converge to a fully exponentially-localized regime for strong disorder. For smooth surface particles, it is found that the states localize first at the band bottom and a mobility edge can clearly be defined for increasing disorder. This doesn't seem to be the case for the rougher particles, where the band middle and the band bottom show similar behavior towards localization. Although particles with surface irregularities show an onset of localization for smaller values of the disorder than smooth particles, the localization length is greater. (orig.)

Physics at the FCC-hh, a 100 TeV pp collider

CERN Document Server

2017-01-01

A 100 TeV pp collider is under consideration, by the high-energy physics community, as an important step for the future development of our field, following the completion of the LHC and High-luminosity LHC physics programmes. In particular, CERN is considering 100 TeV pp collisions as the key target of a Future Circular Collider facility, built around a 100 km tunnel and designed to deliver pp, e+e- and ep collisions, in addition to a programme with heavy ion beams and with the injector complex. CERN is coordinating an international study tasked with the completion, by the end of 2018, of a Conceptual Design Report (CDR) for this facility. This document presents the first results of the assessment of the physics potential of the hadronic part of this research programme (FCC-hh).

Out-of-phase flashing induced instabilities in CIRCUS facility

Energy Technology Data Exchange (ETDEWEB)

Christian Pablo Marcel; Van der Hagen, T.H.J.J. [Interfaculty Reactor Institute, Delft University of Technology, Mekelweg 15, 2629 JB Delft (Netherlands)

2005-07-01

Full text of publication follows: Flashing-induced instabilities are very important during the startup phase of natural-circulation boiling water reactors. To study this type of instability an axial fully scaled facility named CIRCUS was constructed. Experiments at low power and low pressure (typical startup conditions) are carried out on this steam/water natural circulation loop with two parallel risers. A detailed measurement of the void-fraction profile is possible by using needle-probes and the use of glass tubes for the riser and core sections allow to use optical techniques for velocity measurements. The flashing and the mechanism of flashing-induced instabilities are analyzed paying special attention on the strong coupling effect between the two riser channels. It is clear from the experiments that the out-of-phase instability is much more susceptible to occur than the in-phase instability in a system with two parallel risers. The instability region is found as soon as the operational boundary between single-phase and two-phase operation is crossed. The relation between the period of the oscillations and the fluid transient time is also investigated. The stability map constructed using this experimental data is also discussed. (authors)

1978 annual report

International Nuclear Information System (INIS)

1978-06-01

In fiscal 1978 efforts continued to be made to increase New Brunswick's energy independence through research into and development of indigenous power sources including coal, peat, tidal, and hydroelectric resources. At Point Lepreau nuclear generating station the reactor building was completed, the concrete vault was prepared, and the calandria was installed. Work continued within the reactor building. Excavation of the cooling water tunnels and riser shafts was completed. (LL)

In situ transmission electron microscopy study of ion-irradiated copper: comparison of the temperature dependence of cascade collapse in fcc- and bcc-metals

International Nuclear Information System (INIS)

Daulton, T.L.; Kirk, M.A.; Rehn, L.E.

2000-01-01

The kinetics which drive cascade formation and subsequent collapse into point-defect clusters are investigated by analyzing the microstructure produced in situ by low fluence 100 keV Kr ion irradiations of fcc-Cu over a wide temperature range (18-873 K). The yield of collapsed point-defect clusters is demonstrated unequivocally to be temperature dependent, remaining approximately constant up to lattice temperatures of 573 K and then abruptly decreasing with increasing temperature. This drop in yield is not caused by defect loss during or following ion irradiation. In addition, this temperature dependence can be explained by a thermal spike effect. These in situ yield measurements are compared to previous ex situ yield measurements in fcc-Ni and bcc-Mo

Experimental study of the vortex-induced vibration of drilling risers under the shear flow with the same shear parameter at the different Reynolds numbers.

Science.gov (United States)

Liangjie, Mao; Qingyou, Liu; Shouwei, Zhou

2014-01-01

A considerable number of studies for VIV under the uniform flow have been performed. However, research on VIV under shear flow is scarce. An experiment for VIV under the shear flow with the same shear parameter at the two different Reynolds numbers was conducted in a deep-water offshore basin. Various measurements were obtained by the fiber bragg grating strain sensors. Experimental data were analyzed by modal analysis method. Results show several valuable features. First, the corresponding maximum order mode of the natural frequency for shedding frequency is the maximum dominant vibration mode and multi-modal phenomenon is appeared in VIV under the shear flow, and multi-modal phenomenon is more apparent at the same shear parameter with an increasing Reynolds number under the shear flow effect. Secondly, the riser vibrates at the natural frequency and the dominant vibration frequency increases for the effect of the real-time tension amplitude under the shear flow and the IL vibration frequency is the similar with the CF vibration frequency at the Reynolds number of 1105 in our experimental condition and the IL dominant frequency is twice the CF dominant frequency with an increasing Reynolds number. In addition, the displacement trajectories at the different locations of the riser appear the same shape and the shape is changed at the same shear parameter with an increasing Reynolds number under the shear flow. The diagonal displacement trajectories are observed at the low Reynolds number and the crescent-shaped displacement trajectories appear with an increasing Reynolds number under shear flow in the experiment.

Experimental study of the vortex-induced vibration of drilling risers under the shear flow with the same shear parameter at the different Reynolds numbers.

Directory of Open Access Journals (Sweden)

Mao Liangjie

Full Text Available A considerable number of studies for VIV under the uniform flow have been performed. However, research on VIV under shear flow is scarce. An experiment for VIV under the shear flow with the same shear parameter at the two different Reynolds numbers was conducted in a deep-water offshore basin. Various measurements were obtained by the fiber bragg grating strain sensors. Experimental data were analyzed by modal analysis method. Results show several valuable features. First, the corresponding maximum order mode of the natural frequency for shedding frequency is the maximum dominant vibration mode and multi-modal phenomenon is appeared in VIV under the shear flow, and multi-modal phenomenon is more apparent at the same shear parameter with an increasing Reynolds number under the shear flow effect. Secondly, the riser vibrates at the natural frequency and the dominant vibration frequency increases for the effect of the real-time tension amplitude under the shear flow and the IL vibration frequency is the similar with the CF vibration frequency at the Reynolds number of 1105 in our experimental condition and the IL dominant frequency is twice the CF dominant frequency with an increasing Reynolds number. In addition, the displacement trajectories at the different locations of the riser appear the same shape and the shape is changed at the same shear parameter with an increasing Reynolds number under the shear flow. The diagonal displacement trajectories are observed at the low Reynolds number and the crescent-shaped displacement trajectories appear with an increasing Reynolds number under shear flow in the experiment.

Hydrogen diffusion and trapping in bcc and fcc metals

International Nuclear Information System (INIS)

Richter, D.

1979-01-01

The fundamental aspects of the metal--hydrogen systems are described. The large number of anomalous properties are the reason for continuous scientific effort. The time scale of hydrogen motion is extremely short. The characteristic frequencies of the localized modes of hydrogen in Ta, Nb, or V are in the order of 10 -14 sec (energies between 0.1 to 0.2 eV); the jump frequencies for H-diffusion at elevated temperatures in those systems are between 10 +12 to 10 +13 sec -1 . They are comparable with the correlation times for diffusion in liquids and more than ten orders of magnitude larger than the jump times for nitrogen in Nb. Out of the large number of experimental data this paper will survey only some recent results on representative fcc and bcc metals for dilute H solutions. The nature of the elementary step in H-diffusion is described. Here the temperature and isotope dependence of the H-diffusion coefficient gives hints to the mechanism involved. The experimental results are discussed in terms of semiclassical and quantum mechanical diffusion theories

Scenario for Precision Beam Energy Calibration in FCC-ee

CERN Document Server

Koop, I A

2015-01-01

The resonance depolarization method was very successfully used in the experiments at LEP, where the mass of the Z-boson was determined with the relative uncertainty [1, 2]. In the future FCC-ee circular electron-positron collider the luminosity at Z-peak (beam energy 45.5 GeV) is expected be 4-5 orders of magnitude higher and one goal is to perform the same experiments as at LEP, but with much greater accuracy, approaching the level of [3]. Obviously this can be done only by measuring the spin precession frequency. But there are many problems which still need to be solved on the way towards a complete design. The first one: the self-polarization takes too long a time. The Sokolov-Ternov polarization time is about 250 hours at Z-peak. One approach is to install the special field-asymmetric polarizing wigglers to make the self-polarization time much shorter [4, 5] and to utilize only few percent of the polarization degree to measure the resonance spin precession frequency. But these very strong wigglers substan...

Vacancy behavior in a compressed fcc Lennard-Jones crystal

International Nuclear Information System (INIS)

Beeler, J.R. Jr.

1981-12-01

This computer experiment study concerns the determination of the stable vacancy configuration in a compressed fcc Lennard-Jones crystal and the migration of this defect in a compressed crystal. Isotropic and uniaxial compression stress conditions were studied. The isotropic and uniaxial compression magnitudes employed were 0.94 less than or equal to eta less than or equal to 1.5, and 1.0 less than or equal to eta less than or equal to 1.5, respectively. The site-centered vacancy (SCV) was the stable vacancy configuration whenever cubic symmetry was present. This includes all of the isotropic compression cases and the particular uniaxial compression case (eta = √2) that give a bcc structure. In addition, the SCV was the stable configuration for uniaxial compression eta 1.20, the SV-OP is an extended defect and, therefore, a saddle point for SV-OP migration could not be determined. The mechanism for the transformation from the SCV to the SV-OP as the stable form at eta = 1.29 appears to be an alternating sign [101] and/or [011] shear process

FRAUD/SABOTAGE Killing Nuclear-Reactors!!! ``Super"alloys GENERIC ENDEMIC Wigner's-Disease IN-stability!!!

Science.gov (United States)

Asphahani, Aziz; Siegel, Sidney; Siegel, Edward

2010-03-01

Siegel [[J.Mag.Mag.Mtls.7,312(78); PSS(a)11,45(72); Semis.& Insuls.5(79)] (at: ORNL, ANS, Westin``KL"ouse, PSEG, IAEA, ABB) warning of old/new nuclear-reactors/spent-fuel-casks/refineries/ jet/missile/rocket-engines austenitic/FCC Ni/Fe-based (so MIS- called)``super"alloys(182/82;Hastelloy-X; 600;304/304L-SSs; 690 !!!) GENERIC ENDEMIC EXTANT detrimental(synonyms): Wigner's- diseas(WD)[J.Appl.Phys.17,857(46)]; Ostwald-ripening; spinodal- decomposition; overageing-embrittlement; thermomechanical- INstability: Mayo[Google: ``If Leaks Could Kill"; at flickr.com search on ``Giant-Magnotoresistance"; find: [SiegelPolitics(79)]; Hoffman[animatedsoftware.com],...what DOE/NRC MISlabels as ``butt-welds" ``stress-corrosion cracking" endpoint's ROOT-CAUSE ULTIMATE-ORIGIN is WD overageing-embrit- tlement caused brittle-fracture cracking from early/ongoing AEC/DOE-n``u''tional-la``v''atories sabotage!!!

FRAUD/SABOTAGE Killing Nuclear-Reactors Need Modeling!!!: "Super"alloys GENERIC ENDEMIC Wigner's-Disease/.../IN-stability: Ethics? SHMETHICS!!!

Science.gov (United States)

Asphahani, Aziz; Siegel, Sidney; Siegel, Edward

2010-03-01

Carbides solid-state chemistry domination of old/new nuclear- reactors/spent-fuel-casks/refineries/jet/missile/rocket-engines in austenitic/FCC Ni/Fe-based(so miscalled)``super"alloys(182/82; Hastelloy-X,600,304/304L-SSs,...,690!!!) GENERIC ENDEMIC EXTANT detrimental(synonyms): Wigner's-diseas(WD)[J.Appl.Phys.17,857 (1946)]/Ostwald-ripening/spinodal-decomposition/overageing- embrittlement/thermal-leading-to-mechanical(TLTM)-INstability: Mayo[Google:``If Leaks Could Kill"; at flickr.com search on ``Giant-Magnotoresistance"; find: Siegel[J.Mag.Mag.Mtls.7,312 (1978)]Politics(1979)]-Hoffman[animatedsoftware.com], what DOE/NRC MISlabels as ``butt-welds" ``stress-corrosion cracking" endpoint's ROOT-CAUSE ULTIMATE-ORIGIN is WD overageing-embritt- lement caused brittle-fracture cracking from early/ongoing AEC/ DOE-n"u"tional-la"v"atories sabotage!!!

Energy of the Isolated Metastable Iron-Nickel FCC Nanocluster with a Carbon Atom in the Tetragonal Interstice.

Science.gov (United States)

Bondarenko, Natalya V; Nedolya, Anatoliy V

2017-12-01

The energy of the isolated iron-nickel nanocluster was calculated by molecular mechanics method using Lennard-Jones potential. The cluster included a carbon atom that drifted from an inside octahedral interstice to a tetrahedral interstice in [Formula: see text] direction and after that in direction to the surface. In addition, one of 14 iron atoms was replaced by a nickel atom, the position of which was changing during simulation.The energy of the nanocluster was estimated at the different interatomic distances. As a result of simulation, the optimal interatomic distances of Fe-Ni-C nanocluster was chosen for the simulation, in which height of the potential barrier was maximal and face-centered cubic (FCC) nanocluster was the most stable.It is shown that there were three main positions of a nickel atom that significantly affected nanocluster's energy.The calculation results indicated that position of the carbon atom in the octahedral interstice was more energetically favorable than tetrahedral interstice in the case of FCC nanocluster. On the other side, the potential barrier was smaller in the direction [Formula: see text] than in the direction .This indicates that there are two ways for carbon atom to drift to the surface of the nanocluster.

Experimental study of liquid carryover in a separator drum

International Nuclear Information System (INIS)

Prabhudharwadkar, Deoras M.; More, Rahul Z.; Iyer, Kannan N.

2010-01-01

The phenomenon of carryover, i.e. entrainment of liquid along with separated steam is observed in all the steam separators. Due to the risks, such as turbine blade erosion and radioactivity leakage, associated with it, it is desired to have an estimate of the carryover value. This is all the more important when the separation is only under the influence of gravity as proposed in some of the new generation natural circulation reactors. Experiments were carried out in an air-water facility at atmospheric conditions to characterize the entrainment in drums with ratio of the drum diameter to riser diameter varying from 1 to 6. Various parameters influencing the liquid entrainment were identified. The vapour superficial velocity and the drum diameter to riser diameter ratio were found to be the most influencing parameters. A dimensionless prediction correlation was evolved for the liquid entrainment and it was found to agree with previous works in the literature for drum to riser diameter ratio equal to 1.

Vacancy-mediated fcc/bcc phase separation in Fe1 -xNix ultrathin films

Science.gov (United States)

Menteş, T. O.; Stojić, N.; Vescovo, E.; Ablett, J. M.; Niño, M. A.; Locatelli, A.

2016-08-01

The phase separation occurring in Fe-Ni thin films near the Invar composition is studied by using high-resolution spectromicroscopy techniques and density functional theory calculations. Annealed at temperatures around 300 ∘C ,Fe0.70Ni0.30 films on W(110) break into micron-sized bcc and fcc domains with compositions in agreement with the bulk Fe-Ni phase diagram. Ni is found to be the diffusing species in forming the chemical heterogeneity. The experimentally determined energy barrier of 1.59 ±0.09 eV is identified as the vacancy formation energy via density functional theory calculations. Thus, the principal role of the surface in the phase separation process is attributed to vacancy creation without interstitials.

Thermal-hydraulic analysis of bayonet cooling thimble in fuel drain tank of ORNL 10 MW MSRE

International Nuclear Information System (INIS)

Sun Lu; Sun Licheng; Yan Changqi

2012-01-01

The residual heat removal system of molten salt reactor designed by ORNL, using molten salt as fuel and draining the fuel into fuel drain tank after shutdown of the reactor, removes the decay heat by the circulation of water through the bayonet cooling thimbles in the fuel drain tank. According to structural features of the bayonet cooling thimbles in ORNL 10 MW molten salt reactor experiment (MSRE), this paper presents the analytical results of the influence of the width of gas gap and the width of steam riser on the heat removal ability and the natural circulation of the cooling water, etc. The analysis results show that, when the width of gas gap range from 3.1 mm to 5.1 mm, the change of heat dissipation power and natural circulation flow rate are both less than 5%; when the width of steam riser changes from 3.6 mm to 5.1 mm, the flow mass of the natural circulation change from 1.9 kg/s to 4.79 kg/s, with a slightly effect on the heat transfer efficiency of the system. (authors)

Observations and measurements of dynamic effects due to beam-beam interactions in the LHC and extrapolation to the FCC-hh

CERN Document Server

Goncalves Jorge, Patrik

The Future Circular hadron-hadron Collider (FCC-hh) is a design study for a 100 TeV centre-of-mass energy. The dynamics of the beams in such a collider poses many challenges, in particular the amount of energy stored in each beam (8.4 GJ) makes them very destructive and therefore requires a tight control of the machine and beam parameters during the full cycle in order to avoid damages and reach the collider designed performances. The FCC-hh features an increase of the beam brightness during the cycle due to the presence of synchrotron radiation damping at high energy. As a result, the electromagnetic forces that the two beams exert on each other, the so-called beam-beam forces, are enhanced and might become an issue for the safe operation of the machine. In this new regime, the impact of the beam-beam interaction on the optics becomes non-negligible. In this master thesis, for the first time, the impact of the beam-beam interaction on the optics ($\\beta$-beating) is measured in a hadron collider (LHC). The e...

COMPUTATIONAL AND EXPERIMENTAL MODELING OF SLURRY BUBBLE COLUMN REACTORS

Energy Technology Data Exchange (ETDEWEB)

Paul C.K. Lam; Isaac K. Gamwo; Dimitri Gidaspow

2002-05-01

The objective of this study was to develop a predictive experimentally verified computational fluid dynamics (CFD) model for gas-liquid-solid flow. A three dimensional transient computer code for the coupled Navier-Stokes equations for each phase was developed and is appended in this report. The principal input into the model is the viscosity of the particulate phase which was determined from a measurement of the random kinetic energy of the 800 micron glass beads and a Brookfield viscometer. The details are presented in the attached paper titled ''CFD Simulation of Flow and Turbulence in a Slurry Bubble Column''. This phase of the work is in press in a referred journal (AIChE Journal, 2002) and was presented at the Fourth International Conference on Multiphase Flow (ICMF 2001) in New Orleans, May 27-June 1, 2001 (Paper No. 909). The computed time averaged particle velocities and concentrations agree with Particle Image Velocimetry (PIV) measurements of velocities and concentrations, obtained using a combination of gamma-ray and X-ray densitometers, in a slurry bubble column, operated in the bubbly-coalesced fluidization regime with continuous flow of water. Both the experiment and the simulation show a down-flow of particles in the center of the column and up-flow near the walls and nearly uniform particle concentration. Normal and shear Reynolds stresses were constructed from the computed instantaneous particle velocities. The PIV measurement and the simulation produced instantaneous particle velocities. The PIV measurement and the simulation produced similar nearly flat horizontal profiles of turbulent kinetic energy of particles. To better understand turbulence we studied fluidization in a liquid-solid bed. This work was also presented at the Fourth International Conference on Multiphase Flow (ICMF 2001, Paper No. 910). To understand turbulence in risers, measurements were done in the IIT riser with 530 micron glass beads using a PIV

Modelling of the intragranular back-stress and recovery in FCC single crystals and polycrystals

Energy Technology Data Exchange (ETDEWEB)

Sauzay, M

2003-07-01

High temperature mechanical tests including recovery times on FCC metals or alloys involve at least two mechanisms. First, the formation of a two phase dislocation microstructure (cells, walls/channels... ) induces intragranular back-stress and hardening. Second, if the recovery time and the temperature are large enough, the previously formed dislocation microstructure can disappear, even if no remote stress is applied. Simple models of these two mechanisms are proposed. They are based on TEM observations and are validated comparing with several measurements from the literature. These models do not use arty fitted parameter and could help to predict the macroscopic behavior during creep-fatigue tests. (author)

Modelling of the intragranular back-stress and recovery in FCC single crystals and polycrystals

International Nuclear Information System (INIS)

Sauzay, M.

2003-01-01

High temperature mechanical tests including recovery times on FCC metals or alloys involve at least two mechanisms. First, the formation of a two phase dislocation microstructure (cells, walls/channels... ) induces intragranular back-stress and hardening. Second, if the recovery time and the temperature are large enough, the previously formed dislocation microstructure can disappear, even if no remote stress is applied. Simple models of these two mechanisms are proposed. They are based on TEM observations and are validated comparing with several measurements from the literature. These models do not use arty fitted parameter and could help to predict the macroscopic behavior during creep-fatigue tests. (author)

Comparison of void strengthening in fcc and bcc metals: Large-scale atomic-level modelling

International Nuclear Information System (INIS)

Osetsky, Yu.N.; Bacon, D.J.

2005-01-01

Strengthening due to voids can be a significant radiation effect in metals. Treatment of this by elasticity theory of dislocations is difficult when atomic structure of the obstacle and dislocation is influential. In this paper, we report results of large-scale atomic-level modelling of edge dislocation-void interaction in fcc (copper) and bcc (iron) metals. Voids of up to 5 nm diameter were studied over the temperature range from 0 to 600 K. We demonstrate that atomistic modelling is able to reveal important effects, which are beyond the continuum approach. Some arise from features of the dislocation core and crystal structure, others involve dislocation climb and temperature effects

Formation of catalyst deposits in flue gas slide valves at an FCC unit: an experimental solution; Formacao de depositos de catalisador em valvula corredica dos gases de combustao de unidade de FCC: uma experiencia de solucao

Energy Technology Data Exchange (ETDEWEB)

Silva, Luiz Eduardo Magalhaes Correa da; Rodrigues, Jayme Thadeu [PETROBRAS (Brazil). Refinaria Alberto Pasqualini

1990-04-01

We describe flue gas slide valve sticking at the FCC (fluid catalytic cracking) Unit Alberto Pasqualini Refinery (REFAP/PETROBRAS). Findings show that this sticking was due to the formation of catalyst deposits below the slide valve guides. A retrospective survey has suggested that what caused troubleshooting was dragging by medium steam in the cat cracker. We present a theoretical formulation to account for catalyst deposit formation, as well as some points that should be observed in order to minimize the problem. (author) 13 refs., 8 figs., 2 tabs.

Critical heat flux and flow instability in an advanced light water reactor

International Nuclear Information System (INIS)

Dae-Hyun Hwang; Kyong-Won Seo; Chung-Chan Lee; Sung-Kyun Zee

2005-01-01

Full text of publication follows: An advanced light water reactor concept has been continuously studied in KAERI with an output in the range of about 60 to 300 MW th . The reactor is purposed to be utilized as an energy source for seawater desalination as well as small scale power generation. In order to achieve the intrinsic safety and enhanced operational flexibility, some specific design considerations such as low power density and soluble boron free operation have been incorporated in the multiple-parallel-channel type reactor core. The low power density can be achieved by adopting fuel assemblies with tightly spaced non-square lattice rod array. The allowable core operating region should be primarily limited by the two design parameters; the critical heat flux(CHF) and the flow instabilities in the multiple parallel fuel assembly channels. The characteristics of CHF and flow instability have been investigated through experimental and analytical works. The CHF prediction model was established on the basis of experimental data obtained from 19-rod test bundles. The CHF experiments have been conducted for various test bundles with different heated lengths, uniform and non-uniform radial and axial power distributions, water and Freon as the working fluids, and different number of unheated rods. The parametric ranges of CHF experiments covers the pressure from 6 to 18 MPa, the mass flux from 150 to 2000 kg/m 2 /s, and the inlet subcooling from 10 to 120 deg. C. The flow instabilities due to density wave oscillations were investigated by conducting experiments with two parallel channels under the pressure ranges from 6 to 16 MPa. The parametric behavior of flow instability was examined for the test sections with different lengths of adiabatic risers, different axial power shapes, different inlet restrictions, and different channel cross sections. The stability boundary was experimentally determined by increasing channel inlet temperature or reducing the flow rate

Fuel cycle cost uncertainty from nuclear fuel cycle comparison

International Nuclear Information System (INIS)

Li, J.; McNelis, D.; Yim, M.S.

2013-01-01

This paper examined the uncertainty in fuel cycle cost (FCC) calculation by considering both model and parameter uncertainty. Four different fuel cycle options were compared in the analysis including the once-through cycle (OT), the DUPIC cycle, the MOX cycle and a closed fuel cycle with fast reactors (FR). The model uncertainty was addressed by using three different FCC modeling approaches with and without the time value of money consideration. The relative ratios of FCC in comparison to OT did not change much by using different modeling approaches. This observation was consistent with the results of the sensitivity study for the discount rate. Two different sets of data with uncertainty range of unit costs were used to address the parameter uncertainty of the FCC calculation. The sensitivity study showed that the dominating contributor to the total variance of FCC is the uranium price. In general, the FCC of OT was found to be the lowest followed by FR, MOX, and DUPIC. But depending on the uranium price, the FR cycle was found to have lower FCC over OT. The reprocessing cost was also found to have a major impact on FCC

Feasibility evaluation of using spent FCC catalyst for metals treatment from industrial waste; Avaliacao do potencial de recuperacao de niquel de catalisadores equilibrados (E-CAT) atraves da tecnica de remediacao eletrocinetica

Energy Technology Data Exchange (ETDEWEB)

Baptista, Adalberto; Ponte, Haroldo de Araujo [Universidade Federal do Parana (UFPR), Curitiba, PR (Brazil)

2004-07-01

The purpose of this work is to describe the feasibility evaluation using FCC catalyst for treatment from industrial wastes increasing the life time of the spent catalysts and reducing the environmental impact. Evaluated the reutilization of catalyst in process recovery of nickel adsorbed. The technique used was the Electrokinetic Remediation. This technique is based in application of a direct current of low intensity or low potential between the electrodes located in soil. The pollutants are mobilized how loaded species or particles. It used a electrokinetic reactor with approximated volume of 1200 cm{sup 3}, where the residue is placed. In your extremity are adapted two cameras of acrylic, being one anodic, with steel inox 304 electrode, and other cathodic, with lead electrode. In anodic camera, it was injected, with aid a bomb, a solution of sulfuric acid, which work as electrolyte, to a flow rate of 20 ml/h. Was evaluated the desorption of Nickel in the equilibrium catalyst submitting a variation of the conditions of the concentration and potential. (author)

Effect of Rh-based additives on NO and CO formed during regeneration of spent FCC catalyst

Energy Technology Data Exchange (ETDEWEB)

Iliopoulou, E.F.; Efthimiadis, E.A.; Vasalos, I.A. [Aristotle University of Thessaloniki and Center for Research and Technology Hellas, Chemical Process Engineering Research Institute, Department of Chemical Engineering, P.O. Box 1517, 54006 University City, Thessaloniki (Greece); Barth, J.-O.; Lercher, J.A. [Institut fur Technische Chemie, Technische Universitat Munchen, Lichtenbergstrasse 4, D-85748 Garching (Germany)

2004-02-10

Regeneration studies of spent FCC catalyst were performed in a bench-scale unit under reaction conditions that sufficiently simulate those in the regenerator of the fluid catalytic cracking (FCC) unit. The effect of a conventional Pt-based CO promoter (CP-3) on the composition of flue gases was examined. As expected addition of CP-3 in the catalytic inventory decreased CO emissions by one order of magnitude, but tripled the NO emissions independently of the concentration of CO promoter used. Addition of a series of Rh-based catalysts modified the composition of flue gases emitted during regeneration. The parameters under study were the catalytic support, the Rh loading on the additive, and the amount of additive used during regeneration. Both a stoichiometric spinel MgO{center_dot}Al{sub 2}O{sub 3} of high crystallinity and a commercial alumina were competent supports. Promotion of the alumina support with Ce or performing regeneration introducing CO did not affect the additive performance significantly. A combined performance of CO oxidation and NO reduction was achieved minimizing both the Rh loading in the additive (0.1wt.%) and the concentration of additive used during regeneration (1wt.%). IR studies suggest that NO reduction by CO over Rh/alumina additives proceeds via the dissociative adsorption of NO, the formation of NCO species on Rh and their migration to the alumina support to finally yield N{sub 2} and CO{sub 2}.

Ab initio pair potentials for FCC metals: An application of the method of Moebius transform

International Nuclear Information System (INIS)

Mookerjee, A.; Chen Nanxian; Kumar, V.; Satter, M.A.

1991-10-01

We use the method of Moebius transform introduced by one of us (Chen, Phys. Rev. Lett. 64, 1193 (1990)) to obtain pair potentials for fcc metals from first principles total energy calculations. The derivation is exact for radial potentials and it converges much faster than the earlier reported method of Carlsson-Gelatt-Ehrenreich. We have tested this formulation for Cu using the tight binding representation of the linear muffin tin orbital method. Our results agree with those obtained by Carlsson et al. and qualitatively with the other Morse-type pair potentials derived from effective medium theories. (author). 18 refs, 3 figs, 3 tabs

Mobile application MDDCS for modeling the expansion dynamics of a dislocation loop in FCC metals

Science.gov (United States)

Kirilyuk, Vasiliy; Petelin, Alexander; Eliseev, Andrey

2017-11-01

A mobile version of the software package Dynamic Dislocation of Crystallographic Slip (MDDCS) designed for modeling the expansion dynamics of dislocation loops and formation of a crystallographic slip zone in FCC-metals is examined. The paper describes the possibilities for using MDDCS, the application interface, and the database scheme. The software has a simple and intuitive interface and does not require special training. The user can set the initial parameters of the experiment, carry out computational experiments, export parameters and results of the experiment into separate text files, and display the experiment results on the device screen.

Numerical modelling of micro-machining of f.c.c. single crystal: Influence of strain gradients

KAUST Repository

Demiral, Murat

2014-11-01

A micro-machining process becomes increasingly important with the continuous miniaturization of components used in various fields from military to civilian applications. To characterise underlying micromechanics, a 3D finite-element model of orthogonal micro-machining of f.c.c. single crystal copper was developed. The model was implemented in a commercial software ABAQUS/Explicit employing a user-defined subroutine VUMAT. Strain-gradient crystal-plasticity and conventional crystal-plasticity theories were used to demonstrate the influence of pre-existing and evolved strain gradients on the cutting process for different combinations of crystal orientations and cutting directions. Crown Copyright © 2014.

Spin-glass behavior in the S=1/2 fcc ordered perovskite Sr2CaReO6

International Nuclear Information System (INIS)

Wiebe, C.R.; Greedan, J.E.; Luke, G.M.; Gardner, J.S.

2002-01-01

The ordered perovskite Sr 2 CaReO 6 of monoclinic symmetry [space group P2 1 /n,a=5.7556(3) A,b=5.8534(3) A,c=8.1317(4) A,β=90.276(5) deg. at T=4 K] has been synthesized using standard solid-state chemistry techniques. The difference in the size and charge of the cations induces an ordering of the B site Ca 2+ and Re 6+ ions which leads to a distorted fcc lattice of spin-(1/2) Re 6+ (5d 1 ) moments. dc magnetic susceptibility measurements indicate a maximum at T G ∼14 K and an irreversibility in the field-cooled and zero-field-cooled data at ∼22 K that is believed to be caused by the geometric frustration inherent in the fcc structure. Neutron-scattering measurements confirm the absence of magnetic long-range order, and muon spin relaxation experiments indicate the presence of an abrupt spin freezing at T G . Specific heat measurements reveal a broad anomaly typical of spin glasses and no sharp feature. 65% of the spin entropy is released at low temperatures. The low-temperature data do not show the expected linear temperature dependence, but rather a T 3 relationship, as is observed, typically, for antiferromagnetic spin waves. The material is characterized as an unconventional, essentially disorder-free, spin glass

Size dependent hcp-to-fcc transition temperature in Co nanoclusters obtained by ion implantation in silica

International Nuclear Information System (INIS)

Mattei, G.; Maurizio, C.; Fernandez, C Julian de; Mazzoldi, P.; Battaglin, G.; Canton, P.; Cattaruzza, E.; Scian, C.

2006-01-01

In this work we present in situ investigations on the increase of the hcp-to-fcc transition temperature for Co with respect to the bulk value (420 deg. C) when nanoclusters are considered. Starting from Co:SiO 2 composites obtained by ion implantation with average Co cluster size of about 5 nm, a transition temperature between 800 deg. C and 900 deg. C is found upon thermal annealing in vacuum by in situ transmission electron microscopy. Preliminary results on electron irradiation to promote the transition at lower temperatures are presented

arXiv Energy-Frontier Lepton-Hadron Collisions at CERN: the LHeC and the FCC-eh

CERN Document Server

Kuze, Masahiro

2018-05-03

Lepton-hadron colliders that use a proton or nucleus beam of current and future hadron colliders and let it collide with an electron beam from a newly built electron accelerator bring attractive physics programs which are strong and complementary to the hadron collider physics. Machine development for Energy Recovery LINAC and physics performance studies of such electron-hadron colliders, specifically the LHeC that uses the existing LHC beam and FCC-eh that is an option of Future Circular Collider program, are ongoing and reviewed in this article.

EVALUACIÓN MICROMAGNÉTICA DEL NIVEL DE TENSIONES EN ALAMBRES DE TRACCIÓN DE RISERS FLEXIBLES

Directory of Open Access Journals (Sweden)

JOSÉ MATOS

2013-01-01

Full Text Available En el presente trabajo se describe el uso de un método no destructivo que combina las medidas de los parámetros micromagnéticos para cuantificar las tensiones durante los ensayos de tracción en alambres que componen la armadura estructural de risers flexibles. Este método consideró las técnicas de análisis armónico del campo magnético tangencial, análisis de ruido Barkhausen y el análisis del incremento de la permeabilidad, mediante el ensayo de tracción con carga controlada. Se utiliza la regresión lineal de multiparámetros para analizar los datos de cada técnica en forma individual y en conjunto, con el objetivo de correlacionar los valores conocidos de las cargas con los valores medidos en los ensayos realizados. Los resultados muestran una buena relación de los valores obtenidos mediante el método micromagnético y las cargas aplicadas a los cuerpos de prueba, demostrando la eficacia de la técnica en estas aplicaciones.

Statistical study of defects caused by primary knock-on atoms in fcc Cu and bcc W using molecular dynamics

Energy Technology Data Exchange (ETDEWEB)

Warrier, M., E-mail: Manoj.Warrier@gmail.com [Computational Analysis Division, BARC, Visakhapatnam, Andhra Pradesh, 530012 (India); Bhardwaj, U.; Hemani, H. [Computational Analysis Division, BARC, Visakhapatnam, Andhra Pradesh, 530012 (India); Schneider, R. [Computational Science, Ernst-Moritz-Arndt University, D-17489 Greifswald (Germany); Mutzke, A. [Max-Planck-Institut für Plasmaphysik, D-17491 Greifswald (Germany); Valsakumar, M.C. [School for Engineering Sciences and Technology, University of Hyderabad, Gachibowli, Hyderabad, Telangana State, 500046 (India)

2015-12-15

We report on molecular Dynamics (MD) simulations carried out in fcc Cu and bcc W using the Large-scale Atomic/Molecular Massively Parallel Simulator (LAMMPS) code to study (i) the statistical variations in the number of interstitials and vacancies produced by energetic primary knock-on atoms (PKA) (0.1–5 keV) directed in random directions and (ii) the in-cascade cluster size distributions. It is seen that around 60–80 random directions have to be explored for the average number of displaced atoms to become steady in the case of fcc Cu, whereas for bcc W around 50–60 random directions need to be explored. The number of Frenkel pairs produced in the MD simulations are compared with that from the Binary Collision Approximation Monte Carlo (BCA-MC) code SDTRIM-SP and the results from the NRT model. It is seen that a proper choice of the damage energy, i.e. the energy required to create a stable interstitial, is essential for the BCA-MC results to match the MD results. On the computational front it is seen that in-situ processing saves the need to input/output (I/O) atomic position data of several tera-bytes when exploring a large number of random directions and there is no difference in run-time because the extra run-time in processing data is offset by the time saved in I/O. - Highlights: • MD simulations of collision cascades in 200 random directions explored in the energy range of 1–5 keV for fcc Cu and bcc W. • 60–80 random directions must be sampled for the number of displacements produced in a collision cascade to stabilize. • In-cascade clustering of interstitials and vacancies occur. • Direction averaged distribution of interstitials and vacancies around the origin of a PKA is presented. • Comparisons with MD indicate that the recoils produced in BCA-MC simulations be checked for recombination against all vacancies created.

About the choice of Gibbs' potential for modelling of FCC ↔ HCP transformation in FeMnSi-based shape memory alloys

Science.gov (United States)

Evard, Margarita E.; Volkov, Aleksandr E.; Belyaev, Fedor S.; Ignatova, Anna D.

2018-05-01

The choice of Gibbs' potential for microstructural modeling of FCC ↔ HCP martensitic transformation in FeMn-based shape memory alloys is discussed. Threefold symmetry of the HCP phase is taken into account on specifying internal variables characterizing volume fractions of martensite variants. Constraints imposed on model constants by thermodynamic equilibrium conditions are formulated.

Exploring the triplet parameters space to optimise the final focus of the FCC-hh

CERN Document Server

AUTHOR|(CDS)2141109; Abelleira, Jose; Seryi, Andrei; Cruz Alaniz, Emilia

2017-01-01

One of the main challenges when designing final focus systems of particle accelerators is maximising the beam stay clear in the strong quadrupole magnets of the inner triplet. Moreover it is desirable to keep the quadrupoles in the triplet as short as possible for space and costs reasons but also to reduce chromaticity and simplify corrections schemes. An algorithm that explores the triplet parameter space to optimise both these aspects was written. It uses thin lenses as a first approximation and MADX for more precise calculations. In cooperation with radiation studies, this algorithm was then applied to design an alternative triplet for the final focus of the Future Circular Collider (FCC-hh).

Multiphase flows with phase change

Indian Academy of Sciences (India)

Multiphase flows with phase change are ubiquitous in many industrial sectors ranging from energy and infra-structure to specialty chemicals and pharmaceuticals. My own interest in mul- tiphase flows with phase change started more than 15 years ago when I had initiated work on riser reactor for fluid catalytic cracking and ...

Precision natural SUSY at CEPC, FCC-ee, and ILC

International Nuclear Information System (INIS)

Fan, JiJi; Reece, Matthew; Wang, Lian-Tao

2015-01-01

Testing the idea of naturalness is and will continue to be one of the most important goals of high energy physics experiments. It will play a central role in the physics program of future colliders. In this paper, we present projections of the reach of natural SUSY at future lepton colliders: CEPC, FCC-ee and ILC. We focus on the observables which give the strongest reach, the electroweak precision observables (for left-handed stops), and Higgs to gluon and photon decay rates (for both left- and right-handed stops). There is a “blind spot” when the stop mixing parameter X t is approximately equal to the average stop mass. We argue that in natural scenarios, bounds on the heavy Higgs bosons from tree-level mixing effects that modify the hbb̄ coupling together with bounds from b→sγ play a complementary role in probing the blind spot region. For specific natural SUSY scenarios such as folded SUSY in which the top partners do not carry Standard Model color charges, electroweak precision observables could be the most sensitive probe. In all the scenarios discussed in this paper, the combined set of precision measurements will probe down to a few percent in fine-tuning.

First Considerations on Beam Optics and Lattice Design for the Future Hadron-Hadron Collider FCC

CERN Document Server

Alemany Fernandez, R

2014-01-01

The present document explains the steps carried out in order to make the first design of the Future Hadron-Hadron Collider (FCC-hh) following the base line parameters that can be found in [1]. Two lattice layouts are presented, a ring collider with 12 arcs and 12 straight sections, four of them designed as interaction points, and a racetrack like collider with two arcs and two straight sections, each of them equipped with two interaction points. The lattice design presented in the paper is modular allowing the same modules be used for both layouts. The present document addresses as well the beta star reach at the interaction points.

Moessbauer spectroscopy of isotope separator implanted sup(119m)Sn in FCC metals

International Nuclear Information System (INIS)

Larsen, A.N.; Weyer, G.

1979-01-01

Radioactive sup(119m)Sn has been implanted in FCC metals by means of an isotope separator. Moessbauer spectra have been measured for the 24 keV transition of 119 Sn. Large substitutional fractions are found in all cases. A correlation for substitutional lattice sites between the measured isomer shifts of the impurity atoms and the force constants of the host lattices is discussed. Debye-Waller factors determined for substitutional Sn in the host lattices are found to be smaller than values calculated by a simple mass-defect model. For some host metals indications of an influence of radiation damage on the spectra are observed. Defect sites are assigned to Sn in aluminium and lead. Qualitative conclusions on the structures of these defects are drawn from the determined Moessbauer parameters. (author)