WorldWideScience

Sample records for fan atomized oil

  1. Field testing the prototype BNL fan-atomized oil burner

    Energy Technology Data Exchange (ETDEWEB)

    McDonald, R.; Celebi, Y. [Brookhaven National Lab., Upton, NY (United States)

    1995-04-01

    BNL has developed a new oil burner design referred to as the Fan Atomized burner System. The primary objective of the field study was to evaluate and demonstrate the reliable operation of the Fan Atomized Burner. The secondary objective was to establish and validate the ability of a low firing rate burner (0.3-0.4 gph) to fully satisfy the heating and domestic hot water load demands of an average household in a climate zone with over 5,000 heating-degree-days. The field activity was also used to evaluate the practicality of side-wall venting with the Fan Atomized Burner with a low stack temperature (300F) and illustrate the potential for very high efficiency with an integrated heating system approach based on the Fan Atomized Burner.

  2. Market assessment for the fan atomized oil burner

    Energy Technology Data Exchange (ETDEWEB)

    Westphalen, D. [A.D. Little, Inc., Cambridge, MA (United States)

    1996-07-01

    The market potential for the fan atomized burner (FAB) in water and space heating applications was examined. The major findings of the study are as follows. (1). The FAB`s low-input capability allows development of oil-fired room heaters and wall furnaces, a new market area for oil heat. (2). Among conventional oil-fired products, furnaces will benefit most from the burner`s low input capability due to (1) their quick delivery of heat and (2) their more prevalent use in warmer climates and smaller homes. (3). The greatest potential for increased product sales or oil sales exists in the use of the burner with new products (i.e., room heaters). Sales of boilers and direct-fired water heaters are not likely to increase with the use of the burner. (4). Acceptance of the burner will be dependent on proof of reliability. Proof of better reliability than conventional burners would accelerate acceptance.

  3. Fan Atomized Burner design advances & commercial development progress

    Energy Technology Data Exchange (ETDEWEB)

    Kamath, B. [Heat-Wise, Inc., Ridge, NY (United States); Butcher, T.A. [Brookhaven National Lab., Upton, NY (United States)

    1996-07-01

    As a part of the Oil Heat Research and Development program, sponsored by the US Department of Energy, Brookhaven National Laboratory (BNL) has an on-going interest in advanced combustion technologies. This interest is aimed at: improving the initial efficiency of heating equipment, reducing long term fouling and efficiency degradation, reducing air pollutant emissions, and providing practical low-firing rate technologies which may lead to new, high efficiency oil-fired appliances. The Fan-Atomized Burner (FAB) technology is being developed at BNL as part of this general goal. The Fan-Atomized Burner uses a low pressure, air atomizing nozzle in place of the high pressure nozzle used in conventional burners. Because it is air-atomized the burner can operate at low firing rates without the small passages and reliability concerns of low input pressure nozzles. Because it uses a low pressure nozzle the burner can use a fan in place of the small compressor used in other air-atomized burner designs. High initial efficiency of heating equipment is achieved because the burner can operate at very low excess air levels. These low excess air levels also reduce the formation of sulfuric acid in flames. Sulfuric acid is responsible for scaling and fouling of heat exchanger surfaces.

  4. Characterization of fan spray atomizers through numerical simulation

    Energy Technology Data Exchange (ETDEWEB)

    Altimira, Mireia [Thermal and Fluids Engineering Division, Mechanical Engineering Department, Tecnun (University of Navarra), Manuel de Lardizabal 13, 20018 San Sebastian (Spain)], E-mail: maltimira@tecnun.es; Rivas, Alejandro; Larraona, Gorka S.; Anton, Raul; Ramos, Juan Carlos [Thermal and Fluids Engineering Division, Mechanical Engineering Department, Tecnun (University of Navarra), Manuel de Lardizabal 13, 20018 San Sebastian (Spain)

    2009-04-15

    The present paper focuses on the mathematical modeling of industrial fan spray atomizers. The two-phase flow taking place inside the nozzle's tip and the exterior region near the outlet of three different industrial nozzle designs has been modeled and simulated. As a result, valuable information has been obtained regarding the influence of the inner geometry on the flow and also the formation and development of the liquid sheet. Characteristic magnitudes such as the discharge coefficient and the liquid sheet thickness factor have been obtained and validated through experimental measurements. The accumulation of liquid at the border of fan-shaped liquid sheets, also known as rim, has been studied in the analyzed designs, revealing the presence of a tangential velocity component in the liquid sheet and a relationship between the incoming flow rate of the rim and the angle of the liquid sheet. The dependence of the results on turbulence modeling has also been analyzed, drawing interesting conclusions regarding their influence on the liquid sheet mean flow characteristics and on the surrounding gas. Thus, the mathematical model developed has been proved to be a useful tool for nozzle manufacturers; it provides the most important characteristic parameters of the liquid sheet formed given certain nozzle geometry and, additionally, those data necessary to carry out studies of instability, breakup and atomization of the liquid sheet.

  5. The BNL fan-atomized burner system prototype

    Energy Technology Data Exchange (ETDEWEB)

    Butcher, T.A.; Celebi, Y. [Brookhaven National Lab., Upton, NY (United States)

    1995-04-01

    Brookhaven National Laboratory (BNL) has a continuing interest in the development of advanced oil burners which can provide new capabilities not currently available with pressure atomized, retention head burners. Specifically program goals include: the ability to operate at firing rates as low as 0.25 gph; the ability to operate with very low excess air levels for high steady state efficiency and to minimize formation of sulfuric acid and iron sulfate fouling; low emissions of smoke, CO, and NO{sub x} even at very low excess air levels; and the potential for modulation - either staged firing or continuous modulation. In addition any such advanced burner must have production costs which would be sufficiently attractive to allow commercialization. The primary motivation for all work sponsored by the US DOE is, of course, improved efficiency. With existing boiler and furnace models this can be achieved through down-firing and low excess air operation. Also, with low excess air operation fouling and efficiency degradation due to iron-sulfate scale formation are reduced.

  6. Effects of Formulated Glyphosate and Adjuvant Tank Mixes on Atomization from Aerial Application Flat Fan Nozzles

    Science.gov (United States)

    2012-01-01

    flat fans, hollow cones , straight streams, air induction, and electrostatic nozzles. Additionally, nozzles, such as rotary atomizers, may introduce...imparted by the airstream, they will shatter [24,25]. When the for- mulated glyphosate product had additional adjuvants added, the changes (ei- ther increase...Experimental Study of Drop Size Distribution in the Bag Breakup Regime,” Ind. Eng. Chem. Res., Vol. 50, No. 16, 2011, 9767–9773. [25] Lane, W. R., “ Shatter of

  7. Impact Seeded Fault Data of Helicopter Oil Cooler Fan Bearings

    Science.gov (United States)

    2011-11-01

    and a tachometer signal to provide a measure of the shaft speed. Data were acquired using a National Instruments-based PXI system; the vibration data...approximately 40–45 min in duration) of the bearings to measure stable vibration signals—the ―baseline test‖ for the different fault conditions tested...5. Examples of Axial and Radial Vibration Data 13 6. Conclusion 15 7. References 16 Distribution List 17 iv List of Figures Figure 1. Oil

  8. Economic Recovery of Oil Trapped at Fan Margins Using High Angle Wells and Multiple Hydraulic Fractures

    Energy Technology Data Exchange (ETDEWEB)

    Mike L. Laue

    1997-05-30

    The distal fan margin in the northeast portion of the Yowlumne field contains significant reserves but is not economical to develop using vertical wells. Numerous interbedded shales and deteriorating rock properties limit producibility. In addition, extreme depths (13,000 ft) present a challenging environment for hydraulic fracturing and artificial lift. Lastly, a mature waterflood increases risk because of the uncertainty with size and location of flood fronts. This project attempts to demonstrate the effectiveness of exploiting the distal fan margin of this slope-basin clastic reservoir through the use of a high-angle well completed with multiple hydraulic-fracture treatments. The combination of a high-angle (or horizontal) well and hydraulic fracturing will allow greater pay exposure than can be achieved with conventional vertical wells while maintaining vertical communication between thin interbedded layers and the wellbore. The equivalent production rate and reserves of three vertical wells are anticipated at one-half to two-thirds the cost.

  9. 一次除尘风机稀油润滑系统的改进%Improvement of Oil Lubrication System for Primary De-dust Fans

    Institute of Scientific and Technical Information of China (English)

    邓志宏; 彭绍南; 漆良明

    2011-01-01

    通过更换供油泵和增加一个低位油箱,解决了在低转速下风机轴瓦和耦合器轴承的润滑问题,也杜绝了风机轴瓦漏油现象,确保了风机的正常运行。通过更换大容积高位事故油箱,为事故和故障的处理创造了条件,有效的防止了恶性事故的发生。%The feed oil pump is changed and a lower oil tank is installed to meet the needs of the lubrication of fan bearing bush and coupler bearing at the lower speed and eliminate the oil leakage of fan bearing bush and ensure the.fans in a normal operation. The overhead emergency oil tank is replaced with a new one with a larger volume, better for accident and/or fault treatment and effective prevention of serious accidents.

  10. Inductively coupled plasma--atomic emission spectrometry: trace elements in oil matrices

    Energy Technology Data Exchange (ETDEWEB)

    Peterson, C. A.

    1977-12-01

    The simultaneous determination of up to 20 trace elements in various oil matrices by inductively coupled plasma-atomic emission spectrometry is reported. The oil matrices investigated were lubricating oils (for wear metals), fuel oil, centrifuged coal liquefaction product, crude soybean oil, and commercial edible oils. The samples were diluted with appropriate organic solvents and injected into the plasma as an aerosol generated by a pneumatic nebulization technique. Detection limits of the 28 elements studied ranged from 0.0006 to 9 ..mu..g/g with the majority falling in the 0.01 to 0.1 ..mu..g/g range. Analytical calibration curves were linear over at least two orders of magnitude and for some elements this linearity extended over 4.5 orders of magnitude. Relevant data on precision and accuracy are included. Because metals often occur as particles in lubricating oil and coal liquefaction products, the effect of particles on the analytical results was examined. Wear metal particles in used oil did not appear to affect the analytical results. However, incomplete recovery relative to organometallic reference solutions was obtained for iron particles with a nominal mean diameter of 3.0 ..mu..m suspended in oil. It was shown that the following factors contributed to incomplete recovery for the particles: settling of the suspended particles in the flask, a difference in nebulization efficiency between particle suspensions and organometallic solutions, and indications of incomplete vaporization of the larger particles in the plasma.

  11. Efficient Atomization and Combustion of Emulsified Crude Oil

    Science.gov (United States)

    2014-09-18

    175 Characterization Factor, K 11.77 MCR, wt% 9.86 TBP YIELDS, VOL % Butanes and Lighter 0.918 Light Gasoline (55-175 °F) 2.832 Light Naphtha ...175-300 °F) 8.297 Heavy Naphtha (300-400 °F) 7.267 Kerosene (400-500 °F) 8.244 Atm. Gas Oil (500-650 °F) 14.304 Lt Vacuum Gas Oil (650-800...Specific Gravity 0.6643 Mercaptan Sulfur, ppm 0.289 Octane Number, Research, Clear 74.4 LIGHT NAPHTHA (175-300 °F) Gravity, °API 56.4 Specific

  12. Oil burners: Crude oil, atomization, and combustion efficiency. (Latest citations from the NTIS bibliographic database). Published Search

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-06-01

    The bibliography contains citations concerning fuel properties and boiler operations techniques to make maximum use of heavy crude oil, shale oil, and low grade fuels to reduce energy costs in boiler firing. Fuel properties pertain to chemical constituents, viscosity, desulfurization, and processing methods to upgrade the fuels. Operating techniques include atomization, dual-fuel burners, emission characteristics, and cost factors. Combustion efficiency is examined and some citations report on additives or processing techniques to improve the efficiency. The citations also report on studies of health effects in the use of synfuels, mostly as coal liquids to replace oil. (Contains 50-250 citations and includes a subject term index and title list.) (Copyright NERAC, Inc. 1995)

  13. Ky Fan inequalities

    CERN Document Server

    Moslehian, Mohammad Sal

    2011-01-01

    There are several inequalities in the literature carrying the name of Ky Fan. We survey these well-known Ky Fan inequalities and some other significant inequalities generalized by Ky Fan and review some of their recent developments.

  14. Atom-probe tomography of tribological boundary films resulting from boron-based oil additives

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Yoon-Jun; Baik, Sung-Il; Bertolucci-Coelho, Leonardo; Mazzaferro, Lucca; Ramirez, Giovanni; Erdemir, Ali; Seidman, D K

    2016-01-15

    Correlative characterization using atom-probe tomography (APT) and transmission electron microscopy (TEM) was performed on a tribofilm formed during sliding frictional testing with a fully formulated engine oil, which also contains a boron-based additive. The tribofilm formed is ~15 nm thick and consists of oxides of iron and compounds of B, Ca, P, and S, which are present in the additive. This study provides strong evidence for boron being embedded in the tribofilm, which effectively reduces friction and wear losses.

  15. Improvement of the Starting Way of Oil-immersed Air-cooled Transformer Cooling Fan%油浸式风冷变压器冷却风机启动方式改进

    Institute of Scientific and Technical Information of China (English)

    刘银

    2014-01-01

    This paper describes several types of oil-immersed air-cooled transformer, and then reviews the development process of the transformer cooling machine and their advantages and disadvantages, analyzes the development and usage of air-cooled oil-immersed transformer in China, and proposes to control cooling fan starting by oil temperature value.%本文首先介绍了油浸式风冷变压器的几种类型,然后回顾了各种变压器冷却机的发展历程和优缺点,并分析了油浸式风冷变压器在我国的发展使用情况,并且给出了用油温值控制冷却风机启动的建议。

  16. Atomic absorption techniques for determining vanadium and nickel in crude oil

    Energy Technology Data Exchange (ETDEWEB)

    Grizzle, P.L.; Wilson, C.A.; Ferrero, E.P.; Coleman, H.J.

    1977-05-01

    Four different techniques for sample preparation were evaluated for determining vanadium and nickel in crude oils by atomic absorption (AA) spectroscopy: (1) The flame-analyzed dilution method which consists of direct-flame AA analysis after diluting the sample with a suitable organic solvent; (2) the flame-analyzed, wet-ashing method in which the sample is combusted and the residue is then dissolved before flame analysis; (3) the flameless, dilution method which involves flameless AA analysis of the sample following dilution with a suitable organic solvent; and (4) the direct, flameless method in which the crude oil or residue is directly analyzed by flameless AA. The flame-analyzed dilution method yielded erratic and inaccurate analytical results for samples of crude oils as well as for a residual sample containing standard amounts of vanadium and nickel; hence, it is unsatisfactory for oil-identification. Similarly, the direct, flameless method is unsatisfactory owing to the small concentration range available for analysis (less than approximately 15 ppM). Both the flame-analyzed, wet-ashing and flameless-dilution methods yield reliable and reproducible (better than 10%) quantitative data for nickel and vanadium in crude oils and crude oil residues. Results demonstrate that the error associated with the loss of volatile metal containing compounds upon wet-ashing is within the reproducibility of the technique. Although wet-ashing may be slightly more reproducible, the flameless-dilution method is much simpler and faster and is recommended as the better of the two procedures for routine determinations of trace metals for oil identification.

  17. Composite fan stator assembly

    Energy Technology Data Exchange (ETDEWEB)

    Donges, G.L.

    1993-07-13

    A composite fan stator assembly is described for a gas turbine engine having at least two fan rotor stages, the composite stator assembly comprising: an annular composite fan case assembly including an access port, the fan case assembly circumferentially disposed around first and second fan rotor stage locations, a composite fan stator stage supported by and extending radially inward of the fan case assembly and axially disposed between the two fan rotor stage locations, the fan stator stage includes at least one removable vane segment accessible for removal through the access port for assembly and reassembly, the composite fan case assembly including a separable composite forward fan case assembly and a separable composite aft fan case assembly spaced axially aft of the forward fan case assembly, the forward fan case assembly being bolted to the aft fan case assembly, wherein the composite fan stator stage is axially and radially trapped and supported by the forward and aft fan case assemblies. A composite stator vane assembly comprising: a composite inner shroud, a composite outer shroud disposed radially outward of the inner shroud, a plurality of vanes disposed between the shrouds, the vanes including a suction side and a pressure side and radially inner and outer roots, the roots extending through platforms of corresponding ones of the inner and outer shrouds, four box-type attachment elements corresponding to curved suction and pressure sides of the inner and outer roots, the box-type attachment elements having two connected legs angled with respect to each other, a first one of the legs extending along, conforming to the curve of, and bonded to a corresponding one of the airfoil root sides, and a second one of the legs extending along and bonded to a composite shroud surface.

  18. Micro-remaining oil distribution simulation test of fan delta reservoir%扇三角洲储层微观剩余油分布模拟试验

    Institute of Scientific and Technical Information of China (English)

    刘太勋; 徐怀民

    2011-01-01

    利用图像分析系统对大港油田孔南地区某断块孔店组一段扇三角洲储层不同岩相单元样品进行微观孔隙结构的刻画,制作光刻模型,分别采用恒压注水和变压注水的方式开展微观剩余油分布模拟试验,对试验过程进行录像及图像采集,定性和定量地研究微观剩余油的分布,分析不同岩相单元中水驱油过程及微观剩余油分布模式,探讨剩余油分布的控制因素.研究结果表明:扇三角洲储层中剩余油微观分布形态主要有不连通孔隙中由于阻断现象形成的孤岛状剩余油(占剩余油总量的75%)、小孔喉区由于卡断现象形成的剩余油(占剩余油总量的20%)以及珠状、膜状剩余油(不超过剩余油总量的5%);控制不同岩相单元中驱油效率和剩余油分布的因素主要为孔隙结构、驱油压力、驱替流量及流速,孔隙结构类型是影响恒压条件下驱油效率的根本因素,驱油压力和驱油方式是影响驱油效率的关键因素,提高驱油压力、采用变压不稳定注水方式能够使驱油效率提高1倍.%Microscopic pore structure in different types of lithofacies units of fan delta reservoir io the first member of Kongdi-an group was characterized! By photo lithography model and image analysis system in a block of Kongnan area, Dagang Oilfield. Hie distribution of micro-remaining oil was simulated by constant pressure water injection and pressure-swing water injection. The experimental progresses were recorded and the pictures were taken. The distribution modes of tniero-remaining oil in different types of lithofacies units during the wateiflood test were analyzed quantitatively and qualitatively, thus the controlling factors for remaining oil distribution were discussed. The results show that the distribution shapes of ancle-remaining oil in fan delta reservoir mainly include island remaining oil by blocking in the disconnected pore,accounting far about 75% of all

  19. Atoms

    Institute of Scientific and Technical Information of China (English)

    刘洪毓

    2007-01-01

    Atoms(原子)are all around us.They are something like the bricks (砖块)of which everything is made. The size of an atom is very,very small.In just one grain of salt are held millions of atoms. Atoms are very important.The way one object acts depends on what

  20. Sign of the Casimir-Polder interaction between atoms and oil-water interfaces: Subtle dependence on dielectric properties

    CERN Document Server

    Boström, Mathias; Brevik, Iver; Parsons, Drew F; Sernelius, Bo E

    2012-01-01

    We demonstrate that Casimir-Polder energies between noble gas atoms (dissolved in water) and oil-water interfaces are highly surface specific. Both repulsion (e.g. hexane) and attraction (e.g. glycerol and cyclodecane) is found with different oils. For several intermediate oils (e.g. hexadecane, decane, and cyclohexane) both attraction and repulsion can be found in the same system. Near these oil-water interfaces the interaction is repulsive in the non-retarded limit and turns attractive at larger distances as retardation becomes important. These highly surface specific interactions may have a role to play in biological systems where the surface may be more or less accessible to dissolved atoms.

  1. Determination of the total iron content of used lubricating oils by atomic-absorption with use of emulsions.

    Science.gov (United States)

    Salvador, A; de la Guardia, M; Berenguer, V

    1983-12-01

    A new method is proposed for the determination of the total iron content of used lubricating oils. It is based on treatment of the samples with a mixture of hydrofluoric and nitric acids (without destruction of the organic matter) and emulsification, followed by atomic-absorption measurement. This allows the use of aqueous standards and provides a simple, rapid, inexpensive and accurate method, that is not affected by the particle size of the solids in the oil.

  2. Determination of cadmium and lead in edible oils by electrothermal atomic absorption spectrometry after reverse dispersive liquid-liquid microextraction.

    Science.gov (United States)

    López-García, Ignacio; Vicente-Martínez, Yesica; Hernández-Córdoba, Manuel

    2014-06-01

    The dispersive liquid-liquid microextraction of edible oils with a low volume of an acidic solution in the presence of isopropyl alcohol allows cadmium and lead to be completely separated into the aqueous phase. After centrifugation, the metals are determined by electrothermal atomization atomic absorption spectrometry using a palladium salt for chemical modification in the heating cycle. Using a 10 g oil sample, the enrichment factor is 140, which permits detection limits of 0.6 and 10 ng kg(-1) for cadmium and lead, respectively. The results agree with those obtained after sample mineralization. Data for the cadmium and lead levels for 15 samples of different characteristics are given.

  3. Determination of arsenic and cadmium in crude oil by direct sampling graphite furnace atomic absorption spectrometry

    Energy Technology Data Exchange (ETDEWEB)

    Jesus, Alexandre de; Zmozinski, Ariane Vanessa [Instituto de Quimica, Universidade Federal do Rio Grande do Sul, Av. Bento Goncalves 9500, 91501-970 Porto Alegre, RS (Brazil); Damin, Isabel Cristina Ferreira [Faculdade Dom Bosco de Porto Alegre, 90520-280, Porto Alegre, RS (Brazil); Silva, Marcia Messias, E-mail: mmsilva@iq.ufrgs.br [Instituto de Quimica, Universidade Federal do Rio Grande do Sul, Av. Bento Goncalves 9500, 91501-970 Porto Alegre, RS (Brazil); Instituto Nacional de Ciencia e Tecnologia do CNPq, INCT de Energia e Ambiente, Universidade Federal da Bahia, 40170-115 Salvador, BA (Brazil); Vale, Maria Goreti Rodrigues [Instituto de Quimica, Universidade Federal do Rio Grande do Sul, Av. Bento Goncalves 9500, 91501-970 Porto Alegre, RS (Brazil); Instituto Nacional de Ciencia e Tecnologia do CNPq, INCT de Energia e Ambiente, Universidade Federal da Bahia, 40170-115 Salvador, BA (Brazil)

    2012-05-15

    In this work, a direct sampling graphite furnace atomic absorption spectrometry method has been developed for the determination of arsenic and cadmium in crude oil samples. The samples were weighed directly on the solid sampling platforms and introduced into the graphite tube for analysis. The chemical modifier used for both analytes was a mixture of 0.1% Pd + 0.06% Mg + 0.06% Triton X-100. Pyrolysis and atomization curves were obtained for both analytes using standards and samples. Calibration curves with aqueous standards could be used for both analytes. The limits of detection obtained were 5.1 {mu}g kg{sup -1} for arsenic and 0.2 {mu}g kg{sup -1} for cadmium, calculated for the maximum amount of sample that can be analyzed (8 mg and 10 mg) for arsenic and cadmium, respectively. Relative standard deviations lower than 20% were obtained. For validation purposes, a calibration curve was constructed with the SRM 1634c and aqueous standards for arsenic and the results obtained for several crude oil samples were in agreement according to paired t-test. The result obtained for the determination of arsenic in the SRM against aqueous standards was also in agreement with the certificate value. As there is no crude oil or similar reference material available with a certified value for cadmium, a digestion in an open vessel under reflux using a 'cold finger' was adopted for validation purposes. The use of paired t-test showed that the results obtained by direct sampling and digestion were in agreement at a 95% confidence level. Recovery tests were carried out with inorganic and organic standards and the results were between 88% and 109%. The proposed method is simple, fast and reliable, being appropriated for routine analysis. - Highlights: Black-Right-Pointing-Pointer A direct sampling GF AAS method to determine As and Cd in crude oil was proposed. Black-Right-Pointing-Pointer The conventional chemical modifier Pd/Mg has been used to stabilize As and Cd. Black

  4. Investigation of the levels of some element in edible oil samples produced in Turkey by atomic absorption spectrometry

    Energy Technology Data Exchange (ETDEWEB)

    Mendil, Durali, E-mail: dmendil@gop.edu.tr [Gaziosmanpasa University, Faculty of Science and Arts, Chemistry Department, 60250 Tokat (Turkey); Uluoezlue, Ozguer Dogan; Tuezen, Mustafa [Gaziosmanpasa University, Faculty of Science and Arts, Chemistry Department, 60250 Tokat (Turkey); Soylak, Mustafa [Erciyes University, Faculty of Science and Arts, Department of Chemistry, 38039 Kayseri (Turkey)

    2009-06-15

    The element contents (Fe, Mn, Zn, Cu, Pb, Co, Cd, Na, K, Ca and Mg) in edible oils (olive oil, hazelnut oil, sunflower oil, margarine, butter and corn oil) from Turkey were determined using atomic absorption spectrometry after microwave digestion. The concentrations of trace element in the samples were found to be 291.0-52.0, 1.64-0.04, 3.08-1.03, 0.71-0.05, 0.03-0.01, 1.30-0.50, 84.0-0.90, 50.1-1.30, 174.2-20.8 and 20.8-0.60 {mu}g/g for iron, manganese, zinc, copper, lead, cobalt, sodium, potassium, calcium, and magnesium, respectively. Cadmium was found to be 4.57-0.09 {mu}g/kg. The high heavy metal and minerals accumulation levels in the samples were found in olive oil for Cu, Pb, Co, margarine for Fe, K, corn oil for Zn, Mn, butter for Na, Mg, sunflower oil for Ca and hazelnut oil for Cd, respectively.

  5. Survey of reproductive hazards among oil, chemical, and atomic workers exposed to halogenated hydrocarbons

    Energy Technology Data Exchange (ETDEWEB)

    Savitz, D.A.; Harley, B.; Krekel, S.; Marshall, J.; Bondy, J.; Orleans, M.

    1984-01-01

    Several halogenated hydrocarbons are suspected of causing adverse reproductive effects. Because of such concerns, the Oil, Chemical, and Atomic Workers International Union surveyed the reproductive histories of two groups of workers. One group worked at plants engaged in the production or use of halogenated hydrocarbons (exposed) whereas the others had no such opportunity for exposure (nonexposed). Although a low response rate precludes firm conclusions, the 1,280 completed questionnaires provide useful data for generating hypotheses in this developing field of interest. A history of diagnosed cancer was reported more frequently among exposed workers. The infant mortality rate was also significantly elevated among the offspring of exposed workers. No risk gradient was observed for episodes of infertility, fetal loss, congenital defects, or low-birthweight offspring. Concerns with nonresponse, exposure characterization, possible confounding factors, and limited statistical power are addressed. The results provide further suggestions which help to direct studies of occupational reproductive risks.

  6. [Oil atomic spectrometric feature selection by Parzen window based vague sets theory].

    Science.gov (United States)

    Xu, Chao; Zhang, Pei-Lin; Ren, Guo-Quan; Zhang, Xiao-Dong; Yang, Yu-Dong

    2011-02-01

    Large quantity and ambiguity of oil atomic spectrometric information greatly affects the applicable efficiency and accuracy in fault diagnosis. A novel method for choosing less and effective spectrometric features is presented. Based on gearbox test bed, we simulated the normal wear state and two typical faults to acquire the lubricant samples. The three wear states are regarded as three vague sets, and spectrometric feature values are vague values on vague sets. Based on similarity between vague values, mean vague sensibility (MVS) is defined to describe the sensitive degree of spectrometric feature to wear state. Besides, the membership degrees of vague sets greatly depend on human experience. The probability density distribution of spectrometric data of three wear states was estimated with Parzen window. Combined with Bayesian formula, the range of vague sets membership was calculated. Experimental results verify that the proposed method is of efficient help in choosing high fault-sensitive features from so many spectrometric features.

  7. Determination of calcium, magnesium and zinc in unused lubricating oils by atomic absorption spectroscopy.

    Science.gov (United States)

    Udoh, A P

    1995-12-01

    Varying concentrations of lanthanum and strontium were added to solutions of ashed unused lubricating oils for the determination of calcium, magnesium and zinc content using flame atomic absorption spectrophotometry. At least 3000 mug g(-1) of lanthanum or strontium was required to completely overcome the interference of the phosphate ion, PO(3-)(4), and give peak values for calcium. The presence of lanthanum or strontium did not cause an appreciable increase in the amount of magnesium and zinc obtained from the analyses. The method is fast and reproducible, and the coefficients of variation calculated for the elements using one of the samples were 1.6% for calcium, 3.5% for magnesium and 0.2% for zinc. Results obtained by this method were better than those obtained by other methods for the same samples.

  8. Grain-size characteristics and flow strength in the submarine fan deposits from the Qianhe Oil Field, Ludong depression, Liaoning%辽宁陆东凹陷前河油田水下扇沉积粒度特征及水流强度分析

    Institute of Scientific and Technical Information of China (English)

    雷霄雨

    2015-01-01

    The Jiufotang Formation in the Qianhe Oil Field, Ludong depression, Liaoning is built up of a succession of submarine fan deposits generated by the gravity flows and tractional currents during the deposition of the Jiufotang Formation and Shahai Formation. Three sedimentary microfacies have been distinguished, according to lithologic associations and well logs, including the proximal fan, mid-fan front and terminal fan, of which the mid-fan front sandstones turned out to be excellent reservoir rocks because of the discovery of the industrial oil run indicated by the L1 well in the study area.%前河油田九佛堂组为一套水下扇沉积。通过对不同层位取心井粒度资料分析及对比,分析其差异的原因,确定各层位搬运方式及沉积作用形式,并运用霍姆斯水流强度图分析从湖盆边缘向湖盆内的水流强度变化。根据岩性组合及测井曲线特征,识别出扇根、扇中前缘及扇端3种微相。并认为沿水流及砂体发育方向为部署有利区带。

  9. Solar powered headwear fan

    Energy Technology Data Exchange (ETDEWEB)

    Hirsh, G.B.; Volk, S.; Cirrito, W.; Brann, D.

    1987-07-21

    A fan assembly is described. A housing is adapted for resting on an exterior surface of headwear. A fan mounted in the housing at one end of the housing is adapted for forcing air through an opening defined in a forward protuberance of the headwear. Solar cell means are mounted on the housing at another end of the housing opposite to and remote from the one end for powering the fan means and adapted for resting on a crown of the headwear. Vent means are defined by the housing for allowing air to be sucked into the housing and forced out of the housing when the power means drive the fan means. Mounting means are defined by the housing, including hinge means for removably mounting the modular fan assembly on an exterior surface of the headwear. A portion of the housing occupies a substantial distance between the fan means and the solar cell means. Display means are defined by the portion of the housing between the power means and the fan means for displaying of decorative graphic material.

  10. 基于Atom技术的无风扇嵌入式工业电脑%Embedded Industrial Computer Without Fan Based on Atom Technology

    Institute of Scientific and Technical Information of China (English)

    研华科技

    2010-01-01

    @@ 日前,研华自动化推出了2款基于Atom技术的无风扇嵌入式工业电脑,UNO-2173A和UNO-2173AF.UNO-2173A和UNO-2173AF配备Atom 1.6GHz处理器,千兆以太网端口,丰富的I/O接口,同时,带有1个Mini-PCle插孔,可用于支持WLAN、3C及Moblin(移动式Linux)解决方案.这些机型能够兼容Windows 7,并且已经通过Energy Star认证,支持IP-40等级防尘保护和宽温操作(-20~70℃),完美呈现出高性能低功耗的卓越品质.

  11. Comparison of Y-jet and OIL effervescent atomizers based on internal and external two-phase flow characteristics

    Directory of Open Access Journals (Sweden)

    Mlkvik Marek

    2016-01-01

    Full Text Available Presented paper focuses on spraying of two viscous liquids (μ = 60 and 143 mPa·s by two types of twinfluid atomizers with internal mixing. We compared the well-known Y-jet atomizer with the less known, “outside in liquid” (OIL, configuration of the effervescent atomizer. The required liquid viscosity was achieved by using the water-maltodextrin solutions of different concentrations. Both the liquids were sprayed at two gas inlet pressures (Δp = 0.14 and 0.28 MPa and various gas-to-liquid ratios (GLR = 2.5%, 5%, 10% and 20%. The comparison was focused on four characteristics: liquid flow-rate (for the same working regimes, defined by Δp and GLR, internal flow regimes, Weber numbers of a liquid breakup (We and droplet sizes. A high-speed camera and Malvern Spraytec laser diffraction system were used to obtain necessary experimental data. Comparing the results of our experiments, we can state that for both the liquids the OIL atomizer reached higher liquid flow-rates at corresponding working regimes, it was typical by annular internal flow and higher We in the near-nozzle region at all the working regimes. As a result, it produced considerably smaller droplets than the second tested atomizing device, especially for GLR < 10%.

  12. The determination of wear metals in used lubricating oils by flame atomic absorption spectrometry using sulphanilic acid as ashing agent.

    Science.gov (United States)

    Ekanem, E J; Lori, J A; Thomas, S A

    1997-11-01

    A simple and reliable ashing procedure is proposed for the preparation of used lubricating oil samples for the determination of calcium, magnesium, zinc, iron, chromium and nickel by flame atomic absorption spectrometry. Sulphanilic acid was added to oil samples and the mixture coked and the coke ashed at 550 degrees C. The solutions of the ash were analysed by flame AAS for the metals. The release of calcium, zinc, iron and chromium was improved by the addition of sulphanilic acid to samples. The relative standard deviations of metal concentration results in the initial oil samples were 1.5% for Ca (1500 mg l(-1) level), 0.3% for Mg (100 mg l(-1) level), 3.1% for Zn (1500 mg l(-1) level), 0.7% for Fe (500 mg l(-1) level), 0.02% for Cr (50 mg l(-1) level) and 0.002% for Ni (10 mg l(-1) level). The optimum sample size for efficient metal release was 20 g while the optimum sulphanilic acid to oil ratio was 0.05 g per gram of oil for Zn and Cr and 0.10 g for Ca and Fe. Results obtained by this procedure were highly reproducible and comparable with those obtained for the same samples using standard procedures.

  13. Determination of some inorganic metals in edible vegetable oils by inductively coupled plasma atomic emission spectroscopy (ICP-AES

    Directory of Open Access Journals (Sweden)

    Musa Özcan, M.

    2008-09-01

    Full Text Available Seventeen edible vegetable oils were analyzed spectrometrically for their metal (Cu, Fe, Mn, Co, Cr, Pb, Cd, Ni, and Zn contents. Toxic metals in edible vegetable oils were determined by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES. The highest metal concentrations were measured as 0.0850, 0.0352, 0.0220, 0.0040, 0.0010, 0.0074, 0.0045, 0.0254 and 0.2870 mg/kg for copper in almond oil, for iron in corn oil-(c, for manganese in soybean oil, for cobalt in sunflower oil-(b and almond oil, for chromium in almond oil, for lead in virgin olive oil, for cadmium in sunflower oil-(e, for nickel almond oil and for zinc in almond oil respectively. The method for determining toxic metals in edible vegetable oils by using ICP-AES is discussed. The metals were extracted from low quantities of oil (2-3 g with a 10% nitric acid solution. The extracted metal in acid solution can be injected into the ICPAES. The proposed method is simple and allows the metals to be determined in edible vegetable oils with a precision estimated below 10% relative standard deviation (RSD for Cu, 5% for Fe, 15% for Mn, 8% for Co, 10% for Cr, 20% for Pb, 5% for Cd, 16% for Ni and 11% for Zn.En este estudio se analizó espectrométricamente el contenido en metales (Cu, Fe, Mn, Co, Cr, Pb, Cd, Ni, and Zn de 17 aceites vegetales comestibles mediante ICP-AES. Las concentaciones más elevadas se encontraron para el cobre en el aceite de almendra (0.0850 mg/kg, para el hierro en el aceite de maiz(c,(0.0352 mg/kg, para el manganeso en el aceite de soja (0.0220 mg/kg, para el cobalto en el aceite de girasol (b (0.0040 mg/kg, para el cromo en el aceite de almendra (0.0010 mg/kg, para el plomo en el aceite de oliva virgen (0.0074 mg/kg, para el cadmio en el aceite de girasol (e (0.0045 mg/kg, para el niquel en el aceite de almendra (0.0254 mg/kg y para el zincen el aceite de almendra (0.2870 mg/kg. Los metales se extrajeron a partir de bajas cantidades de aceite (2-3 g, con

  14. Determination of aluminum by electrothermal atomic absorption spectroscopy in lubricating oils emulsified in a sequential injection analysis system.

    Science.gov (United States)

    Burguera, José L; Burguera, Marcela; Antón, Raquel E; Salager, Jean-Louis; Arandia, María A; Rondón, Carlos; Carrero, Pablo; de Peña, Yaneira Petit; Brunetto, Rosario; Gallignani, Máximo

    2005-12-15

    The sequential injection (SIA) technique was applied for the on-line preparation of an "oil in water" microemulsion and for the determination of aluminum in new and used lubricating oils by electrothermal atomic absorption spectrometry (ET AAS) with Zeeman-effect background correction. Respectively, 1.0, 0.5 and 1.0ml of surfactants mixture, sample and co-surfactant (sec-butanol) solutions were sequentially aspirated to a holding coil. The sonication and repetitive change of the flowing direction improved the stability of the different emulsion types (oil in water, water in oil and microemulsion). The emulsified zone was pumped to fill the sampling arm of the spectrometer with a sub-sample of 200mul. Then, 10mul of this sample solution were introduced by means of air displacement in the graphite tube atomizer. This sequence was timed to synchronize with the previous introduction of 15mug of Mg(NO(3))(2) (in a 10mul) by the spectrometer autosampler. The entire SIA system was controlled by a computer, independent of the spectrometer. The furnace program was carried out by employing a heating cycle in four steps: drying (two steps at 110 and 130 degrees C), pyrolisis (at 1500 degrees C), atomization (at 2400 degrees C) and cleaning (at 2400 degrees C). The calibration graph was linear from 7.7 to 120mugAll(-1). The characteristic mass (mo) was 33.2pg/0.0044s and the detection limit was 2.3mugAll(-1). The relative standard (RSD) of the method, evaluated by replicate analyses of different lubricating oil samples varied in all cases between 1.5 and 1.7%, and the recovery values found in the analysis of spiked samples ranged from 97.2 to 100.4%. The agreement between the observed and reference values obtained from two NIST Standard Certified Materials was good. The method was simple and satisfactory for determining aluminum in new and used lubricating oils.

  15. Fans af Bruce

    DEFF Research Database (Denmark)

    Vaaben, Nana Katrine

    2007-01-01

    Analysen viser, hvordan det samme ritual under en koncert forener og opdeler de fans, der orienterer sig mod Bruce Springsteen. På den ene side forener ritualet hele publikum i en stor fælles "Intimitet for mange" og på den anden side splitter det dem, fordi det bliver tydeligt, hvem der er de ri...

  16. What a Football Fan

    Institute of Scientific and Technical Information of China (English)

    王保安; 孙鹏

    2004-01-01

    While the football fan was thrilled to be at the Super Bowl, he was disappointed with the location of his seat. Peering across the stadium through his binoculars, he spied an empty seat on the 50-yard line and made his way there.

  17. Determination of trace nickel in hydrogenated cottonseed oil by electrothermal atomic absorption spectrometry after microwave-assisted digestion.

    Science.gov (United States)

    Zhang, Gai

    2012-01-01

    Microwave digestion of hydrogenated cottonseed oil prior to trace nickel determination by electrothermal atomic absorption spectrometry (ETAAS) is proposed here for the first time. Currently, the methods outlined in U.S. Pharmacopeia 28 (USP28) or British Pharmacopeia (BP2003) are recommended as the official methods for analyzing nickel in hydrogenated cottonseed oil. With these methods the samples may be pre-treated by a silica or a platinum crucible. However, the samples were easily tarnished during sample pretreatment when using a silica crucible. In contrast, when using a platinum crucible, hydrogenated cottonseed oil acting as a reducing material may react with the platinum and destroy the crucible. The proposed microwave-assisted digestion avoided tarnishing of sample in the process of sample pretreatment and also reduced the cycle of analysis. The programs of microwave digestion and the parameters of ETAAS were optimized. The accuracy of the proposed method was investigated by analyzing real samples. The results were compared with the ones by pressurized-PTFE-bomb acid digestion and ones obtained by the U.S. Pharmacopeia 28 (USP28) method. The new method involves a relatively rapid matrix destruction technique compared with other present methods for the quantification of metals in oil.

  18. Thermoresponsive Melamine Sponges with Switchable Wettability by Interface-Initiated Atom Transfer Radical Polymerization for Oil/Water Separation.

    Science.gov (United States)

    Lei, Zhiwen; Zhang, Guangzhao; Deng, Yonghong; Wang, Chaoyang

    2017-03-15

    Here we have obtained a temperature responsive melamine sponge with a controllable wettability between superhydrophilicity and superhydrophobicity by grafting the octadecyltrichlorosilane and thermoresponsive poly(N-isopropylacrylamide) (PNIPAAm) onto the surface of melamine sponge skeletons. The whole process included the silanization in which step the rough surface with low surface energy and the NH2 were provided, and the atom transfer radical polymerization which ensured the successful grafting of PNIPAAm onto the skeleton's surface. The product exhibits a good reversible switch between superhydrophilicity and superhydrophobicity by changing the temperature below or above the lower critical solution temperature (LCST, about 32 °C) of PNIPAAm, and the modified sponge still retains a good responsiveness after undergoing two temperature switches for 20 cycles. Simultaneously, the functionalized sponges could be used to absorb the oil under water at 37 °C, and they released the absorbed oil in various ways under water at 20 °C, showing wide potential applications including oil/water separation.

  19. Observational Analysis of Coronal Fans

    Science.gov (United States)

    Talpeanu, D.-C.; Rachmeler, L; Mierla, Marilena

    2017-01-01

    Coronal fans (see Figure 1) are bright observational structures that extend to large distances above the solar surface and can easily be seen in EUV (174 angstrom) above the limb. They have a very long lifetime and can live up to several Carrington rotations (CR), remaining relatively stationary for many months. Note that they are not off-limb manifestation of similarly-named active region fans. The solar conditions required to create coronal fans are not well understood. The goal of this research was to find as many associations as possible of coronal fans with other solar features and to gain a better understanding of these structures. Therefore, we analyzed many fans and created an overview of their properties. We present the results of this statistical analysis and also a case study on the longest living fan.

  20. Fan Cart: The Next Generation

    Science.gov (United States)

    Lamore, Brian

    2016-10-01

    For years the fan cart has provided physics students with an excellent resource for exploring fundamental mechanics concepts such as acceleration, Newton's laws, impulse, momentum, work-energy, and energy conversions. The Physics Teacher has even seen some excellent do-it-yourself (DIY) fan carts and activities. If you are interested in developing the `E' portion of your and your students' STEM (science, technology, engineering, and math) skills, one way to accomplish this is to revisit the DIY fan cart. In this article I share a design of a new edition of the DIY fan cart and some ideas for incorporating the engineering design process into your high school curriculum.

  1. Dynamic and Implications of Football Fans' Club and Fans ...

    African Journals Online (AJOL)

    DrNneka

    Dross (2009) identified football games as one event that has proved potent ... have potential of drawing human attention to participate either as a player or as a ... However, beyond what football fans wears, the fans are sometimes ready to ...

  2. Skífan

    OpenAIRE

    Elín Ólafsdóttir

    2011-01-01

    Skífan er eina fyrirtækið hér á landi sem sérhæfir sig í sölu á tónlist, mynddiskum, tölvuleikjum og leikjatölvum. Sú atvinnugrein sem Skífan tilheyrir hefur fengið að finna töluvert fyrir þróun internetsins þar sem mögulegt er að hlaða þessu efni niður hvort sem er með löglegum eða ólöglegum hætti. Markmið verkefnisins var að skoða hver áhrif sviðsmynda væru á rekstrarlíkan Skífunnar. Höfundur fór í gegnum atvinnuvega- og samkeppnisgreiningu með aðstoð eiganda og rekstrarstjóra Skífunnar...

  3. Polarization-fan high-order harmonics

    Science.gov (United States)

    Fleischer, Avner; Bordo, Eliyahu; Kfir, Ofer; Sidorenko, Pavel; Cohen, Oren

    2017-02-01

    We predict high-order harmonics in which the polarization within the spectral bandwidth of each harmonic varies with frequency continuously and significantly. For example, the interaction of counter-rotating circularly-polarized bichromatic drivers having close central frequencies with isotropic gas leads to the emission of polarization-fan harmonics where each harmonic in the spectrum has the following property: it is nearly circularly-polarized in one tail of the harmonic peak, linear in the center of the peak and nearly circular with the opposite helicity in the opposite tail. Also, we show that polarization-fan high harmonics with modulated ellipticity are obtained when elliptical drivers are used. Polarization-fan harmonics are obtained as a result of multiple (at least two) head-on recollisions of electrons with their parent ions occurring from different angles in a two-dimensional plane. The use of bichromatic drivers with close central frequencies largely preserves the single-cycle, single-atom and macroscopic physics of ‘ordinary’ high harmonic generation, where both the driver and high harmonics are linearly polarized. Thus, it should offer several attracting features, including (i) a direct route for extending the maximal photon energy of observed helical high harmonics to keV by using bichromatic drivers only in the mid-IR region and (ii) utilizing phase matching methods that were developed for ‘ordinary’ high harmonic generation driven by quasi-monochromatic pulses (e.g. pressure tuning phase matching). These polarization-fan harmonics may be utilized for exploring non-repetitive ultrafast chiral phenomena, e.g. dynamics of magnetic domains, in a single shot.

  4. Fan Cart: The Next Generation

    Science.gov (United States)

    Lamore, Brian

    2016-01-01

    For years the fan cart has provided physics students with an excellent resource for exploring fundamental mechanics concepts such as acceleration, Newton's laws, impulse, momentum, work-energy, and energy conversions. "The Physics Teacher" has even seen some excellent do-it-yourself (DIY) fan carts and activities. If you are interested…

  5. Determination of calcium, magnesium and zinc in lubricating oils by flame atomic absorption spectrometry using a three-component solution.

    Science.gov (United States)

    Zmozinski, Ariane V; de Jesus, Alexandre; Vale, Maria G R; Silva, Márcia M

    2010-12-15

    Lubricating oils are used to decrease wear and friction of movable parts of engines and turbines, being in that way essential for the performance and the increase of that equipment lifespan. The presence of some metals shows the addition of specific additives such as detergents, dispersals and antioxidants that improve the performance of these lubricants. In this work, a method for determination of calcium, magnesium and zinc in lubricating oil by flame atomic absorption spectrometry (F AAS) was developed. The samples were diluted with a small quantity of aviation kerosene (AVK), n-propanol and water to form a three-component solution before its introduction in the F AAS. Aqueous inorganic standards diluted in the same way have been used for calibration. To assess the accuracy of the new method, it was compared with ABNT NBR 14066 standard method, which consists in diluting the sample with AVK and in quantification by F AAS. Two other validating methods have also been used: the acid digestion and the certified reference material NIST (SRM 1084a). The proposed method provides the following advantages in relation to the standard method: significant reduction of the use of AVK, higher stability of the analytes in the medium and application of aqueous inorganic standards for calibration. The limits of detection for calcium, magnesium and zinc were 1.3 μg g(-1), 0.052 μg g(-1) and 0.41 μg g(-1), respectively. Concentrations of calcium, magnesium and zinc in six different samples obtained by the developed method did not differ significantly from the results obtained by the reference methods at the 95% confidence level (Student's t-test and ANOVA). Therefore, the proposed method becomes an efficient alternative for determination of metals in lubricating oil.

  6. Optimisation of Fan Blade Angle

    Directory of Open Access Journals (Sweden)

    Swaroop M P

    2017-01-01

    Full Text Available This report represents the optimization of fan blade angle in accordance with the various room temperatures that can be in the tropical area like India. We took this work mainly because cooling is an important factor now a days in every area where construction and rooms are there and ceiling fans are the most common device that is commonly used. So it is of utmost importance to tweak the performance of this ceiling fan so that it can function in its most optimal condition. We have modeled the fan in a modeling software (SOLIDWORKS and imported that into an analyzing software (ANSYS and a result is generated on the various blade angles (0, 4, 8 and 12.5 degrees in accordance to room conditions. A trend line curve with the obtained data is expected as the result which can be crucial for designing of future fans

  7. Determination of metals in lubricating oils by flame atomic absorption spectrometry using a single-bore high-pressure pneumatic nebulizer.

    Science.gov (United States)

    Mora, J; Todolí, J L; Sempere, F J; Canals, A; Hernandis, V

    2000-12-01

    The behaviour of a single-bore high-pressure pneumatic nebulizer (SBHPPN) as a tool for the analysis of lubricating oils by flame atomic absorption spectrometry (FAAS) was investigated. The effects of the sample oil content [from 10% to 100% (w/w) oil in 4-methylpentan-2-one, IBMK] and the carrier nature (IBMK and methanol) on the characteristics of the aerosols generated, on the analyte transport efficiency and on the analytical figures of merit in FAAS were studied. A pneumatic concentric nebulizer (PCN) was used for comparison. Increasing the oil content increases the viscosity of the sample. With the PCN this gives rise to coarser aerosols, making it impossible to nebulize samples with an oil content higher than 70% (w/w). Using the SBHPPN, the viscosity of the sample scarcely affects the characteristics of the primary aerosols. Hence, the SBHPPN is able, by using the appropriate carrier, to nebulize pure lubricating oils. Among the carriers tested, IBMK is the most advisable because it is fully miscible with all the oil samples. The SBHPPN provides higher sensitivities and lower limits of detection than the PCN. Compared with a method based on organic dilution, the use of the SBHPPN for the direct analysis of lubricating oils by FAAS makes it possible, in addition to increasing the analysis throughput, to detect elements at lower concentrations. Moreover, the SBHPPN provides similar results to those obtained using a previous acid digestion step.

  8. A history of RPGs: Made by fans; played by fans

    Directory of Open Access Journals (Sweden)

    Paul Mason

    2012-09-01

    Full Text Available I explore some aspects of the early history of tabletop role-playing games (RPGs that are perhaps not well known among media scholars, and which offer an alternative take on the idea of fan activity.

  9. Proceedings of the 1998 oil heat technology conference

    Energy Technology Data Exchange (ETDEWEB)

    McDonald, R.J.

    1998-04-01

    The 1998 Oil Heat Technology Conference was held on April 7--8 at Brookhaven National Laboratory (BNL) under sponsorship by the US Department of Energy, Office of Building Technologies, State and Community Programs (DOE/BTS). The meeting was held in cooperation with the Petroleum Marketers Association of America (PMAA). Fourteen technical presentations was made during the two-day program, all related to oil-heat technology and equipment, these will cover a range of research, developmental, and demonstration activities being conducted within the United States and Canada, including: integrated oil heat appliance system development in Canada; a miniature heat-actuated air conditioner for distributed space conditioning; high-flow fan atomized oil burner (HFAB) development; progress in the development of self tuning oil burners; application of HFAB technology to the development of a 500 watt; thermophotovoltaic (TPV) power system; field tests of the Heat Wise Pioneer oil burner and Insight Technologies AFQI; expanded use of residential oil burners to reduce ambient ozone and particulate levels by conversion of electric heated homes to oilheat; PMAA`s Oil Heat Technician`s Manual (third edition); direct venting concept development; evolution of the chimney; combating fuel related problems; the effects of red dye and metal contamination on fuel oil stability; new standard for above ground and basement residential fuel oil storage; plastic and steel composite secondary contained tanks; and money left on the table: an economic analysis of tank cleaning.

  10. 14 CFR 29.908 - Cooling fans.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Cooling fans. 29.908 Section 29.908... STANDARDS: TRANSPORT CATEGORY ROTORCRAFT Powerplant General § 29.908 Cooling fans. For cooling fans that are a part of a powerplant installation the following apply: (a) Category A. For cooling fans...

  11. Size dependence of shape and stiffness of single sessile oil nanodroplets as measured by atomic force microscopy.

    Science.gov (United States)

    Munz, Martin; Mills, Tom

    2014-04-22

    This article presents results and guidelines on the quantitative analysis of size, shape, and stiffness of single sessile oil droplets in air and in water. Atomic force microscopy (AFM) facilitates the analysis of micro- and nanoscale droplets which are of growing importance for agrochemicals, cosmetics, or foodstuffs containing emulsions with nanoscale compartments or droplets. Measurement of droplet shape and stiffness provides information on the contact angle with the support surface as well as the interfacial tension of the liquid-liquid interface. In this study, micro- and nanoscale droplets were imaged both in amplitude modulation (AM) and force mapping modes. The effects of the AM mode set point ratio on the measured droplet shape are discussed, and a modified spherical cap model is suggested to extract the droplet-substrate contact angle. This model was applied to a population of different sized oil droplets imaged in water and led to the finding that the contact angle with the solid support varies with the droplet size. Force mapping was undertaken to measure the droplet stiffness as a function of the droplet size. Smaller droplets were found to be stiffer, in reasonable agreement with the Attard-Miklavcic model [Langmuir 2001, 17, 8217-8223] which describes the deformation of a sessile droplet in the nonwetting regime, i.e., by partial wrapping of the droplet around the probe surface. The model limitations are discussed in terms of the diverging droplet stiffness predicted for droplet radii similar to the probe radius as well as the error propagation associated with the droplet shape function.

  12. Stranger than fiction: Fan identity in cosplay

    Directory of Open Access Journals (Sweden)

    Nicolle Lamerichs

    2011-09-01

    Full Text Available Academic accounts of fan cultures usually focus on creative practices such as fan fiction, fan videos, and fan art. Through these practices, fans, as an active audience, closely interpret existing texts and rework them with texts of their own. A practice scarcely examined is cosplay ("costume play", in which fans produce their own costumes inspired by fictional characters. Cosplay is a form of appropriation that transforms and actualizes an existing story in close connection to the fan community and the fan's own identity. I provide analytical insights into this fan practice, focusing on how it influences the subject. Cosplay is understood as a performative activity and analyzed through Judith Butler's concept of performativity. I specifically focus on boundaries between the body and dress, and on those between reality and fiction. I aim to show that cosplay emphasizes the personal enactment of a narrative, thereby offering new perspectives on fan identity.

  13. Football – Feminisation – Fans

    DEFF Research Database (Denmark)

    Mintert, Svenja-Maria

    the number of female fans in football has grown over the past years. A national sense of community, emotion and passion for the game is in particular reached during the international tournaments at live football spectacles and many female fans cheer and sing for ‘their’ team with the utmost conviction. Yet...... sociological theories. The objective is, first, to develop new knowledge and understanding about the impact of football on gendered identity construction and negotiation – in both the performance and the consumption of football – and how these female fans contribute to a European dialogue, the gender......-specific experience and acting out of fandom, and the intersection between gender and national/European identity. The second objective is to study the role of gender in football and fan cultures with regard to gender-specific patterns of cross-cultural communication and identification. The third objective...

  14. Comparison of the Viscous Liquids Spraying by the OIG and the Oil Configurations of an Effervescent Atomizer at Low Inlet Pressures

    Directory of Open Access Journals (Sweden)

    Mlkvik Marek

    2016-07-01

    Full Text Available In this work we studied the influence of the fluid injection configuration (OIG: outside-in-gas, OIL: outside-in-liquid on the internal flows and external sprays parameters. We sprayed the viscous aqueous maltodextrin solutions (μ = 60 mPa·s at a constant inlet pressure of the gas and the gas to the liquid mass flow ratio (GLR within the range 2.5 to 20%. We found that the fluids injection has a crucial influence on the internal flows. The internal flows patterns for the OIG atomizer were the slug flows, the internal flow of the OIL device was annular which led to the significant improvement of the spray quality: Smaller droplets, faster atomization, fewer pulsations.

  15. On Some Generalized Ky Fan Minimax Inequalities

    Directory of Open Access Journals (Sweden)

    Luo Xianqiang

    2009-01-01

    Full Text Available Some generalized Ky Fan minimax inequalities for vector-valued mappings are established by applying the classical Browder fixed point theorem and the Kakutani-Fan-Glicksberg fixed point theorem.

  16. Advance Noise Control Fan II: Test Rig Fan Risk Management Study

    Science.gov (United States)

    Lucero, John

    2013-01-01

    Since 1995 the Advanced Noise Control Fan (ANCF) has significantly contributed to the advancement of the understanding of the physics of fan tonal noise generation. The 9'x15' WT has successfully tested multiple high speed fan designs over the last several decades. This advanced several tone noise reduction concepts to higher TRL and the validation of fan tone noise prediction codes.

  17. Online Fan Fiction and Critical Media Literacy

    Science.gov (United States)

    Black, Rebecca W.

    2010-01-01

    This article explores English-language-learning (ELL) youths' engagement with popular media through composing and publicly posting stories in an online fan fiction writing space. Fan fiction is a genre that lends itself to critical engagement with media texts as fans repurpose popular media to design their own narratives. Analyses describe how…

  18. Fan/Ram Duct Program

    Science.gov (United States)

    1973-10-01

    mwm^mmmt c INPUT I ] H—f TRANSIENT ROUTINE P"" CONTROL """I FAN ] COMPRESSOR MAIN BURNER I DUCT HZ HIGH TURBINE in— LOW TURBINE I...and pressure ratio. 6. Low Turbine Low turbine characteristics, identical In form to those of the high turbine, are shown in figures 27 and 28. 7

  19. School Athletics and Fan Aggression

    Science.gov (United States)

    Bryan, Clifford; Horton, Robert

    1976-01-01

    Several hypotheses are developed regarding fans and their behavior based upon a review of the literature. An exploratory study is then described, in which participant observers at a university sports arena observed cases of aggressive behavior among the spectators. Based upon the literature review and the findings of the study, four…

  20. Evaluation of cadmium, lead, copper, iron and zinc in Turkish dietary vegetable oils and olives using electrothermal and flame atomic absorption spectrometry

    Energy Technology Data Exchange (ETDEWEB)

    Acar, O.

    2012-07-01

    The Cd, Pb, Cu, Fe and Zn contents of some edible vegetable oils (soybean, sunflower, flower, nut, corn and olive) and of olives (olive-1, black, green, black crushed with seeds and green crushed with seeds) were determined and evaluated by an electrothermal atomic absorption spectrometer (ETAAS) using an Sc + Ir + NH{sub 4}H{sub 2}PO{sub 4} chemical modifier mixture and flame atomic absorption spectrometer (FAAS) after microwave digestion. The pyrolysis and atomization temperatures of Cd, Pb and Cu in sample solutions with and without the modifier mixture were investigated. The limits of detection (LOD) for analytes found are 0.1, 0.6, 0.9, 15.0 and 12.0 {mu}g L{sup -}1 for Cd, Cu, Pb, Fe and Zn, respectively. The accuracy of the procedure proposed was confirmed by analyzing bovine liver 1577b standard reference material (SRM) and a spiked sample solution. The results of the analytes found were compared with certified and added values. The relative standard deviations of the analytes found were lower than 7% and the percent of recoveries obtained ranges from 96 to 101%. The Sc + Ir + NH{sub 4}H{sub 2}PO{sub 4} mixture proposed was applied for the determination of Cd, Pb and Cu in oils and olives. The results of analytes found in the samples were compared with international and national food quality guidelines as well as with literature values. (Author) 48 refs.

  1. Ultrasound-assisted single-drop microextraction for the determination of cadmium in vegetable oils using high-resolution continuum source electrothermal atomic absorption spectrometry

    Energy Technology Data Exchange (ETDEWEB)

    Almeida, Jorge S.; Anunciação, Taiana A. [Departamento de Química Analítica, Instituto de Química, Universidade Federal da Bahia, Campus Universitário de Ondina, Salvador, Bahia 40170-280 (Brazil); Brandão, Geovani C. [Departamento de Química Analítica, Instituto de Química, Universidade Federal da Bahia, Campus Universitário de Ondina, Salvador, Bahia 40170-280 (Brazil); INCT de Energia e Ambiente, Instituto de Química, Universidade Federal da Bahia, Campus Universitário de Ondina, Salvador, Bahia 40170-280 (Brazil); Dantas, Alailson F. [Departamento de Química Analítica, Instituto de Química, Universidade Federal da Bahia, Campus Universitário de Ondina, Salvador, Bahia 40170-280 (Brazil); Lemos, Valfredo A. [Laboratório de Química Analítica (LQA), Universidade Estadual do Sudoeste da Bahia, Campus de Jequié, Jequié, Bahia 45506-191 (Brazil); and others

    2015-05-01

    This work presents an ultrasound-assisted single-drop microextraction procedure for the determination of cadmium in vegetable oils using high-resolution continuum source electrothermal atomic absorption spectrometry. Some initial tests showed that the best extraction efficiency was obtained when using ultrasound instead of mechanical agitation, indicating that acoustic cavitation improved the extraction process. Nitric, hydrochloric and acetic acids were evaluated for use in the extraction process, and HNO{sub 3} gave the best results. A two-level full-factorial design was applied to investigate the best conditions for the extraction of Cd from the oil samples. The influences of the sonication amplitude, time and temperature of the extraction were evaluated. The results of the design revealed that all of the variables had a significant effect on the experimental results. Afterward, a Box–Behnken design was applied to determine the optimum conditions for the determination of cadmium in vegetable oil samples. According to a multivariate study, the optimum conditions were as follows: sonication amplitude of 60%, extraction time of 15 min, extraction temperature of 46 °C and 0.1 mol L{sup −1} HNO{sub 3} as the extractor solution. Under optimized conditions, the developed method allows for the determination of Cd in oil samples with a limit of quantification of 7.0 ng kg{sup −1}. Addition and recovery experiments were performed in vegetable oil samples to evaluate the accuracy of the method, and the recoveries obtained varied from 90% to 115%. The samples were also analyzed after the acid digestion procedure, and the paired t-test (95% confidence level) did not show significant differences from the proposed method. - Highlights: • The determination of cadmium in vegetable oils was developed using UA-SDME. • HR-CS ET-AAS was employed as a detection technique with direct drop sampling. • The procedure allowed for a reduction in the consumption of reagents and

  2. Compressor-fan unitary structure for air conditioning system

    Science.gov (United States)

    Dreiman, N.

    2015-08-01

    An extremely compact, therefore space saving unitary structure of short axial length is produced by radial integration of a revolving piston rotary compressor and an impeller of a centrifugal fan. The unitary structure employs single motor to run as the compressor so the airflow fan and eliminates duality of motors, related power supply and control elements. Novel revolving piston rotary compressor which provides possibility for such integration comprises the following: a suction gas delivery system which provides cooling of the motor and supplies refrigerant into the suction chamber under higher pressure (supercharged); a modified discharge system and lubricating oil supply system. Axial passages formed in the stationary crankshaft are used to supply discharge gas to a condenser, to return vaporized cooling agent from the evaporator to the suction cavity of the compressor, to pass a lubricant and to accommodate wiring supplying power to the unitary structure driver -external rotor electric motor.

  3. 原子吸收法快速测定燃油中的铝%Rapid Determination of Aluminium in Fuel Oil by Atomic-absorption Spectrophotometry

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    The determination of aluminium in fuel oil by means of the technique of direct dilution using a mixed-solvent system, inorganic aluminiun standard and atomic absorption spectrophotometry is researched. Good recoveries of aluminium added to fuel oil were demonstrated. Relative standard deviation of 3.6% was reached.%采用无机铝标准物和混合溶剂系统直接稀释-原子吸收法测定燃油中铝,回收率达92.4%,相对标准偏差为3.6%,特征质量浓度为0.85μg/mL.

  4. Direct and simultaneous determination of Cr and Fe in crude oil using high-resolution continuum source graphite furnace atomic absorption spectrometry

    Energy Technology Data Exchange (ETDEWEB)

    Dittert, Ingrid M. [Departamento de Quimica, Universidade Federal de Santa Catarina, Campus Universitario, Trindade, 88040-900, Florianopolis, SC (Brazil); Silva, Jessee S.A. [Centro Federal de Educacao Tecnologica de Santa Catarina, Florianopolis, SC (Brazil); Araujo, Rennan G.O. [Departamento de Quimica, Universidade Federal de Santa Catarina, Campus Universitario, Trindade, 88040-900, Florianopolis, SC (Brazil)], E-mail: rgoa01@terra.com.br; Curtius, Adilson J.; Welz, Bernhard [Departamento de Quimica, Universidade Federal de Santa Catarina, Campus Universitario, Trindade, 88040-900, Florianopolis, SC (Brazil); Becker-Ross, Helmut [ISAS, Institute for Analytical Sciences, Department of Interface Spectroscopy, Albert-Einstein-Str. 9, 12489 Berlin (Germany)

    2009-06-15

    A simple, fast and sensitive direct method for the simultaneous determination of Cr and Fe in crude oil samples is proposed using high-resolution continuum source graphite furnace atomic absorption spectrometry. No sample preparation is used except for a 10-minute homogenization in an ultrasonic bath. Aliquots of 0.1-4 mg of the samples are weighed onto solid sampling platforms and analyzed directly using aqueous standards for calibration. The simultaneous determination was possible because there is a secondary Fe line at 358.120 nm in the vicinity of the most sensitive Cr line at 357.868 nm, and both absorption lines were within the wavelength interval covered by the linear charge-coupled device array detector. It has also been of advantage that the sensitivity ratio between the two analytical lines corresponded roughly to the concentration ratio of the two elements found in crude oil, and that both analytes have very similar volatility, so that no compromises had to be made regarding pyrolysis and atomization temperatures. Two oil reference materials have been analyzed and the results were in agreement with the certified or reported values. Characteristic masses of 3.6 pg and 0.5 ng were obtained for Cr and Fe, respectively. The limits of detection (3{sigma}, n = 10) were 1 {mu}g kg{sup - 1} for Cr and 0.6 mg kg{sup - 1} for Fe, and the precision, expressed as the relative standard deviation, ranged from 4 to 20%, which is often acceptable for a rapid direct analytical procedure. Five crude oils samples were analyzed.

  5. Direct and simultaneous determination of Cr and Fe in crude oil using high-resolution continuum source graphite furnace atomic absorption spectrometry

    Science.gov (United States)

    Dittert, Ingrid M.; Silva, Jessee S. A.; Araujo, Rennan G. O.; Curtius, Adilson J.; Welz, Bernhard; Becker-Ross, Helmut

    2009-06-01

    A simple, fast and sensitive direct method for the simultaneous determination of Cr and Fe in crude oil samples is proposed using high-resolution continuum source graphite furnace atomic absorption spectrometry. No sample preparation is used except for a 10-minute homogenization in an ultrasonic bath. Aliquots of 0.1-4 mg of the samples are weighed onto solid sampling platforms and analyzed directly using aqueous standards for calibration. The simultaneous determination was possible because there is a secondary Fe line at 358.120 nm in the vicinity of the most sensitive Cr line at 357.868 nm, and both absorption lines were within the wavelength interval covered by the linear charge-coupled device array detector. It has also been of advantage that the sensitivity ratio between the two analytical lines corresponded roughly to the concentration ratio of the two elements found in crude oil, and that both analytes have very similar volatility, so that no compromises had to be made regarding pyrolysis and atomization temperatures. Two oil reference materials have been analyzed and the results were in agreement with the certified or reported values. Characteristic masses of 3.6 pg and 0.5 ng were obtained for Cr and Fe, respectively. The limits of detection (3 σ, n = 10) were 1 µg kg - 1 for Cr and 0.6 mg kg - 1 for Fe, and the precision, expressed as the relative standard deviation, ranged from 4 to 20%, which is often acceptable for a rapid direct analytical procedure. Five crude oils samples were analyzed.

  6. WHO ARE FANS OF FACEBOOK FAN PAGES? AN ELECTRONIC WORD-OF-MOUTH COMMUNICATION PERSPECTIVE

    Directory of Open Access Journals (Sweden)

    Xiao Hu

    2014-12-01

    Full Text Available Given its great business value and popularity, Facebook fan pages have attracted more and more attention in both industry and academia. Fans of Facebook fan pages play an important role in electronic word-of-mouth (eWOM communication. This study focused on the population of fans on Facebook fan pages and examined the differences between fans and non-fans in terms of demographics, social network sites (SNS use, Internet use, and online shopping behaviors. The results indicated that fans used SNS more frequently than non-fans. Additionally, from the eWOM perspective, the researchers moderated product types in the model of people’s word-of-mouth (WOM preferences and found that people had different preferences for eWOM and traditional WOM for different products. Traditional WOM is still the most important source of information for people when shopping online.

  7. Football – Feminisation – Fans

    DEFF Research Database (Denmark)

    Mintert, Svenja-Maria

    Football has long time been considered as a genuine masculine domain. However, in the current football culture, the dualism of masculinity and femaleness is in progress. More and more women consume football which is in many countries considered the most popular sport, not only in Scandinavia where...... the number of female fans in football has grown over the past years. A national sense of community, emotion and passion for the game is in particular reached during the international tournaments at live football spectacles and many female fans cheer and sing for ‘their’ team with the utmost conviction. Yet......, the combination ‘women and football’ is still adhered to certain scepticism. Objective The overall objective of this Ph.D. thesis is to contribute to the body of knowledge associated with the distinct aspects of women’s football, female fandom and gender identities in European football drawing upon various...

  8. An Interview with Fan Wu

    Institute of Scientific and Technical Information of China (English)

    李娜

    2006-01-01

    Fan Wu grew up on a farm in South China, in the community to where her parents were exiled during the Cultural Revolution (1966-1976). Wu moved to the United States in 1997, to attend Stanford University, and she began writing in 2002. She now lives and works in northern California, the United State. February Flowers is her first novel. During her recent book tour in China, she took time to talk to Women of China. Women of China (WOC): What inspired

  9. Development of a method for total Hg determination in oil samples by cold vapor atomic absorption spectrometry after its extraction induced by emulsion breaking.

    Science.gov (United States)

    Vicentino, Priscila de O; Brum, Daniel M; Cassella, Ricardo J

    2015-01-01

    This work reports the development of a novel extraction method for total Hg determination in oil samples. After extracting Hg from samples it was quantified in the extracts by cold vapor atomic absorption spectrometry (CV-AAS), employing a laboratory-made gas-liquid separator (GLS) and NaBH4 as reducing agent. The extraction of Hg from samples was carried out by extraction induced by emulsion breaking (EIEB), which is based on the formation and breaking of water-in-oil emulsion between the oil samples and an extractant solution containing an emulsifying agent (surfactant) and nitric acid. Operational parameters of the GLS were evaluated in order to set the best performance of the measurement system. In these studies it was proven that the volume of sample and the concentration of HCl added to the sample extracts had significant influence on Hg response. The best conditions were achieved by adding 0.5 mL of a 0.3 mol L(-1) HCl solution on 1 mL of sample extract. The extraction conditions were also optimized. The highest efficiency was observed when 4 mL of a solution containing 2.5% triton X-100 and 15% v/v HNO3 were employed for the extraction of Hg contained in 20 mL of sample. Emulsion breaking was performed by heating at 80 °C and took approximately 20 min. The limit of quantification of the method was 1.9 µg L(-1) and recovery percentages between 80% and 103% were observed when spiked samples (2 and 10 µg L(-1)) of diesel oil, biodiesel and mineral oil were analyzed.

  10. Acoustic Power Transmission Through a Ducted Fan

    Science.gov (United States)

    Envia, Ed

    2016-01-01

    For high-speed ducted fans, when the rotor flowfield is shock-free, the main contribution to the inlet radiated acoustic power comes from the portion of the rotor stator interaction sound field that is transmitted upstream through the rotor. As such, inclusion of the acoustic transmission is an essential ingredient in the prediction of the fan inlet noise when the fan tip relative speed is subsonic. This paper describes a linearized Euler based approach to computing the acoustic transmission of fan tones through the rotor. The approach is embodied in a code called LINFLUX was applied to a candidate subsonic fan called the Advanced Ducted Propulsor (ADP). The results from this study suggest that it is possible to make such prediction with sufficient fidelity to provide an indication of the acoustic transmission trends with the fan tip speed.

  11. Computing Gröbner fans

    DEFF Research Database (Denmark)

    Fukuda, K.; Jensen, Anders Nedergaard; Thomas, R.R.

    2005-01-01

    This paper presents algorithms for computing the Gröbner fan of an arbitrary polynomial ideal. The computation involves enumeration of all reduced Gröbner bases of the ideal. Our algorithms are based on a uniform definition of the Gröbner fan that applies to both homogeneous and non...... are not always normal fans of polyhedra in which case reverse search applies automatically. Computational results using our implementation of these algorithms in the software package Gfan are included....

  12. REFINEMENTS OF THE FAN-TODD'S INEQUALITIES

    Institute of Scientific and Technical Information of China (English)

    庄国基

    2002-01-01

    Refinements to inequalities oninner product spaces are presented. In this respect, inequalities dealt with in this paper are: Cauchy's inequality, Bessel's inequality, Fan-Todd's inequality and Fan-Todd's determinantal inequality. In each case, a strictly increasing function is put forward, which lies between the smaller and the larger quantities of each inequality. As a result,an improved condition for equality of the Fan-Todd's determinantal inequality is deduced.

  13. The Challenges of Teaching Fan Studies

    DEFF Research Database (Denmark)

    Stephan, Matthias

    , has only gained in popularity. Yet, the nature of the course in question, an interdisciplinary open elective, has meant a class with a variety of backgrounds, preparation, and expectations from fan studies and its critical apparatus. In addition, due to the course being taught in English, it attracts...... a conversation about the best methods for teaching fan studies, and help to open up fan studies to be integrated into other courses and programs....

  14. Active Control of Fan Noise

    Institute of Scientific and Technical Information of China (English)

    Nobuhiko YAMASAKI; Hirotoshi TAJIMA

    2008-01-01

    In the wake-rotor interaction fan noise, a number of the interacting modes at the blade passing frequency (BPF)and its harmonics are generated which are prescribed by the number of stator and rotor blades etc. In the present study, the dominant mode is tried to be suppressed by the secondary sound from the loudspeaker actuators. One of the novel features of the present system is the adoption of the control board with the Field Programmable Gate Array (FPGA) hardware and the LabVIEW software to synchronize the circumferentially installed loudspeaker actuators with the relative location of rotational blades under arbitrary fan rotational speeds. The experiments were conducted under the conditions of three rotational speeds of 2004, 3150, and 4002 [rpm]. The reduction in the sound pressure level (SPL) was observed for all three rotational speeds. The sound pressure level at the BPF was reduced approximately 13 [dB] for 2004 [rpm] case, but not so large reduction was attained for other cases probably due to the inefficiency of the loudspeaker actuators at high frequencies

  15. Highly Loaded Fan by Using Tandem Cascade Rotor Blade

    Science.gov (United States)

    Hasegawa, Hiroaki; Suga, Shinya; Matsuoka, Akinori

    For axial flow compressors and fans in the aircraft engines higher pressure ratio is required in order to attain the high thrust engines. In this study, the fan with the tandem cascades was introduced to increase the fan pressure ratio. The use of tandem cascades in the fan allows savings in length and weight and therefore a compact fan could be built. The design of fan with tandem cascades and the fan testing were carried out to develop the high pressure ratio fan for the Air Turbo Ramjet (ATR) propulsion system. The ATR is a combined cycle engine which performs like a turbojet engine at subsonic speeds and a ramjet at supersonic speeds. In particular, high fan pressure ratio contributes to increase the engine thrust during subsonic flight at which the engine does not make use of ram effect. The results of the fan testing indicate that the pressure ratio of 2.2 is achieved in single stage fan.

  16. Turbofan gas turbine engine with variable fan outlet guide vanes

    Science.gov (United States)

    Wood, Peter John (Inventor); Zenon, Ruby Lasandra (Inventor); LaChapelle, Donald George (Inventor); Mielke, Mark Joseph (Inventor); Grant, Carl (Inventor)

    2010-01-01

    A turbofan gas turbine engine includes a forward fan section with a row of fan rotor blades, a core engine, and a fan bypass duct downstream of the forward fan section and radially outwardly of the core engine. The forward fan section has only a single stage of variable fan guide vanes which are variable fan outlet guide vanes downstream of the forward fan rotor blades. An exemplary embodiment of the engine includes an afterburner downstream of the fan bypass duct between the core engine and an exhaust nozzle. The variable fan outlet guide vanes are operable to pivot from a nominal OGV position at take-off to an open OGV position at a high flight Mach Number which may be in a range of between about 2.5-4+. Struts extend radially across a radially inwardly curved portion of a flowpath of the engine between the forward fan section and the core engine.

  17. Bright Streaks and Dark Fans

    Science.gov (United States)

    2007-01-01

    The south polar region of Mars is covered every year by a layer of carbon dioxide ice. In a region called the 'cryptic terrain,' the ice is translucent and sunlight can penetrate through the ice to warm the surface below. The ice layer sublimates (evaporates) from the bottom. The dark fans of dust seen in this image come from the surface below the layer of ice, carried to the top by gas venting from below. The translucent ice is 'visible' by virtue of the effect it has on the tone of the surface below, which would otherwise have the same color and reflectivity as the fans. Bright streaks in this image are fresh frost. The CRISM team has identified the composition of these streaks to be carbon dioxide. Observation Geometry Image PSP_003113_0940 was taken by the High Resolution Imaging Science Experiment (HiRISE) camera onboard the Mars Reconnaissance Orbiter spacecraft on 26-Mar-2007. The complete image is centered at -85.8 degrees latitude, 106.0 degrees East longitude. The range to the target site was 244.9 km (153.0 miles). At this distance the image scale is 49.0 cm/pixel (with 2 x 2 binning) so objects 147 cm across are resolved. The image shown here has been map-projected to 50 cm/pixel . The image was taken at a local Mars time of 06:20 PM and the scene is illuminated from the west with a solar incidence angle of 79 degrees, thus the sun was about 11 degrees above the horizon. At a solar longitude of 207.6 degrees, the season on Mars is Northern Autumn.

  18. 船用增压锅炉燃油雾化器流动特性数值研究%Numerical Investigation on Flow Characteristics of Oil Atomizer for Marine Supercharged Boiler

    Institute of Scientific and Technical Information of China (English)

    张少凯; 杨元龙; 郑子都

    2015-01-01

    为进一步提高船用增压锅炉的燃烧效率,明晰增压锅炉机械式燃油雾化器的雾化特性,建立船用增压锅炉机械式燃油雾化器的三维模型,采用标准k-ε湍流模型计算雾化器流场的湍流结构,基于CFD数值模拟的方法,得到在不同进口油压下雾化器关键性能参数的分布规律,分析表明,船用锅炉机械式雾化器的喷油口部位动能损失最大,承受流体冲击和剪切作用最强,极易诱发低频振动及结构损坏。%To directly improve combustion efficiency of the marine supercharged boiler and spray characteristics of mechani-cal oil atomizer, a 3D model for oil atomizer of the marine supercharged boiler is established.The flow characteristics of the oil atomizer are studied numerically based on CFX software.The standard k-εturbulence model is used to calculate the flow structure of the oil atomizer field.The distributions of key performance parameters are obtained under different inlet oil pressure condi-tions.The results show that the maximum kinetic energy loss, strongest shear and impact existed on the local injection port of at-omizer, which could induce low frequency vibration and structural damage easily.

  19. Dynamic response of Hovercraft lift fans

    Science.gov (United States)

    Moran, D. D.

    1981-08-01

    Hovercraft lift fans are subjected to varying back pressure due to wave action and craft motions when these vehicles are operating in a seaway. The oscillatory back pressure causes the fans to perform dynamically, exhibiting a hysteresis type of response and a corresponding degradation in mean performance. Since Hovercraft motions are influenced by variations in lift fan pressure and discharge, it is important to understand completely the nature of the dynamic performance of lift fans in order to completely solve the Hovercraft seakeeping problem. The present study was performed to determine and classify the instabilities encountered in a centrifugal fan operating against time-varying back pressure. A model-scale experiment was developed in which the fan discharge was directed into a flow-measuring device, terminating in a rotating valve which produced an oscillatory back pressure superimposed upon a mean aerodynamic resistance. Pressure and local velocity were measured as functions of time at several locations in the fan volute. The measurements permitted the identification of rotating (or propagating) stall in the impeller. One cell and two cell configurations were classified and the transient condition connecting these two configurations was observed. The mechanisms which lead to rotating stall in a centrifugal compressor are presented and discussed with specific reference to Hovercraft applications.

  20. Fan-structure waves in shear ruptures

    Science.gov (United States)

    Tarasov, Boris

    2016-04-01

    This presentation introduces a recently identified shear rupture mechanism providing a paradoxical feature of hard rocks - the possibility of shear rupture propagation through the highly confined intact rock mass at shear stress levels significantly less than frictional strength. According to the fan-mechanism the shear rupture propagation is associated with consecutive creation of small slabs in the fracture tip which, due to rotation caused by shear displacement of the fracture interfaces, form a fan-structure representing the fracture head. The fan-head combines such unique features as: extremely low shear resistance (below the frictional strength), self-sustaining stress intensification in the rupture tip (providing easy formation of new slabs), and self-unbalancing conditions in the fan-head (making the failure process inevitably spontaneous and violent). An important feature of the fan-mechanism is the fact that for the initial formation of the fan-structure an enhanced local shear stress is required, however, after completion of the fan-structure it can propagate as a dynamic wave through intact rock mass at shear stresses below the frictional strength. Paradoxically low shear strength of pristine rocks provided by the fan-mechanism determines the correspondingly low transient strength of the lithosphere, which favours generation of new earthquake faults in the intact rock mass adjoining pre-existing faults in preference to frictional stick-slip instability along these faults. The new approach reveals an alternative role of pre-existing faults in earthquake activity: they represent local stress concentrates in pristine rock adjoining the fault where special conditions for the fan-mechanism nucleation are created, while further dynamic propagation of the new fault (earthquake) occurs at low field stresses even below the frictional strength.

  1. Proceedings of the 1996 oil heat technology conference and workshop

    Energy Technology Data Exchange (ETDEWEB)

    McDonald, R.J.

    1996-07-01

    This Conference is a key technology transfer activity supported by the ongoing Combustion Equipment Technology (Oil-Heat R and D) program at BNL, and is aimed at providing a forum for the exchange of information among international researchers, engineers, manufacturers, and marketers of oil-fired space-conditioning equipment. The objectives of the Conference were to: identify and evaluate the state-of-the-art and recommend new initiatives for higher efficiency, a cleaner environment, and to satisfy consumer needs cost-effectively, reliably, and safely; and foster cooperation among federal and industrial representatives with the common goal of sustained national economic growth and energy security via energy conservation. The 1996 Oil Technology Conference comprised: (a) fourteen technical papers, and (b) four workshops which focused on mainstream issues in oil-heating technology, namely: oilheat research agenda forum; fan atomized burner commercialization, applications, and product development; fuel quality, storage and maintenance--industry discussion; and application of oil heat venting tables, NFPA 31 standard. Selected papers are indexed separately for inclusion in the Energy Science and Technology Database.

  2. Disabled Woman Heads Beijing Fans Association

    Institute of Scientific and Technical Information of China (English)

    1995-01-01

    THE next time you go to a football match in Beijing, look around the edge of the field. You might see a young woman in a wheelchair cheering her favorite team. Wu Jinghong is more than a handicapped person, more than a woman football fan. She is the head of the Beijing Football Fans Association, a group more than 1,000 members strong. Wu alone started the association in 1988 and because she is a woman, encouraged other women fans to openly support their favorite teams.

  3. Sherlock (Holmes in Japanese (fan works [symposium

    Directory of Open Access Journals (Sweden)

    Lori Morimoto

    2017-03-01

    Full Text Available I explore the history of Japanese writing centered on Sherlock Holmes as a means of interrogating the 2014 BBC Sherlock pastiche John and Sherlock Casebook 1: Jon, zenchi renmei e iku (The stark naked league, written by Japanese Sherlockian Kitahara Naohiko for mainstream publication by the publishing house Hayakawa shobō. I argue that exploration of the Japanese (fan cultural contexts of Kitahara's book begins to reveal the limits of the Anglo-American-centered framework through which fan studies scholars explore fan/producer relationships.

  4. 30 CFR 75.311 - Main mine fan operation.

    Science.gov (United States)

    2010-07-01

    ... back-up fan system— (1) Only persons necessary to evaluate the effect of the fan stoppage or restart... back-up fan system is used that does not provide the ventilating quantity provided by the main mine fan... fire or other products of combustion are approved in the ventilation plan. (g) If multiple mine...

  5. PICNIC - FANS, ULTRAS AND HOOLIGANS - INTERNAL DIFFERENTIATE OF SUBCULTURE GROUP FOOTBALL FANS IN POLAND

    Directory of Open Access Journals (Sweden)

    Maciej Solinski

    2006-01-01

    Full Text Available This article is a main part of "Internal differentiate of subculture group of football fans in Poland" project. Author has tried to show how the subculture of football fans can be differentiate. Author ha presented three different subgroups of Polish fans. It is very important to divide this subculture, because each subgroup has different mentality and style. That is why I have paid the most attention on this element.

  6. Knowing fans, knowing music : an exploration of fan interaction on Twitter

    OpenAIRE

    2011-01-01

    In this thesis, I examine what "knowing music" means to participants in online social musicking activities, along with the role Twitter plays in this process. I compare the way I came to "know" music through social networks with others' behaviors regarding music and social networking. Using Henry Jenkins's research framework as an aca-fan (a portmanteau word combining academic and fan), I study fan communities from the inside out. I begin by outlining my story of coming to know the music that...

  7. Numerical Analysis for the Air Flow of Cross Flow Fan

    Science.gov (United States)

    Sakai, Hirokazu; Tokushge, Satoshi; Ishikawa, Masatoshi; Ishihara, Takuya

    There are many factors for designing the cross flow fan. Therefore, the performance of cross flow fan is not clear yet. We can analyze the transient flow of a cross flow fan using sliding mesh approach. One of the tasks using Computational Fluid Dynamics (CFD) is a way of modeling for analysis heat exchangers with cross flow fan. These tasks are very important for design. The paper has a modeling of heat exchangers and meshing the fan blades. The next tasks, we focus the ability of cross flow fan when we change the geometry of fan blades.

  8. Active Vibration Reduction of Titanium Alloy Fan Blades (FAN1) Using Piezoelectric Materials

    Science.gov (United States)

    Choi, Benjamin; Kauffman, Jeffrey; Duffy, Kirsten; Provenza, Andrew; Morrison, Carlos

    2010-01-01

    The NASA Glenn Research Center is developing smart adaptive structures to improve fan blade damping at resonances using piezoelectric (PE) transducers. In this paper, a digital resonant control technique emulating passive shunt circuits is used to demonstrate vibration reduction of FAN1 Ti real fan blade at the several target modes. Single-mode control and multi-mode control using one piezoelectric material are demonstrated. Also a conceptual study of how to implement this digital control system into the rotating fan blade is discussed.

  9. How to do things with fan subs: Media engagement as subcultural capital in anime fan subbing

    Directory of Open Access Journals (Sweden)

    Douglas Schules

    2014-09-01

    Full Text Available Anime fandom has been a fairly constant subject in fan scholarship, although only recently have conversations about fan subbing begun to circulate. As useful as those conversations are, none have directly dealt either with the mechanisms of fan subbing, particularly the use of linear notes, as a practice or with how these subs intersect with the flows of subcultural capital. Fan subbing, both as a productive and a consumptive practice, plays a small but influential part in subcultural capital. Engagement with media is a compositional element of such capital in this community.

  10. Magnetic anomalies in Central Bengal fan

    Digital Repository Service at National Institute of Oceanography (India)

    Rao, T.C.S.; Lakshminarayana, S.; Sarma, K.V.L.N.S.

    Total magnetic field anomalies recorded over the Central Bengal Fan are analysed and the depths to the magnetic basement are computed using the analytical signal and the Werner deconvolution methods. To the west and east of 85 degrees E...

  11. Computing Gröbner fans

    DEFF Research Database (Denmark)

    Fukuda, K.; Jensen, Anders Nedergaard; Thomas, R.R.

    2005-01-01

    This paper presents algorithms for computing the Gröbner fan of an arbitrary polynomial ideal. The computation involves enumeration of all reduced Gröbner bases of the ideal. Our algorithms are based on a uniform definition of the Gröbner fan that applies to both homogeneous and non......-homogeneous ideals and a proof that this object is a polyhedral complex. We show that the cells of a Gröbner fan can easily be oriented acyclically and with a unique sink, allowing their enumeration by the memory-less reverse search procedure. The significance of this follows from the fact that Gröbner fans...

  12. Quiet, High-Efficiency Vaneaxial Fans Project

    Data.gov (United States)

    National Aeronautics and Space Administration — During this Phase I effort, CRG proposes to demonstrate the ability to significantly reduce the acoustic signature of vaneaxial fans by establishing quiet...

  13. Mexican Fan Palm - Orange Co. [ds350

    Data.gov (United States)

    California Department of Resources — This dataset provides the known distribution of Mexican fan palm (Washingtonia robusta) in southern Orange County. The surveys were conducted from May to June, 2007...

  14. Synchronous and Cogged Fan Belt Performance Assessment

    Energy Technology Data Exchange (ETDEWEB)

    Cutler, D.; Dean, J.; Acosta, J.

    2014-02-01

    The GSA Regional GPG Team commissioned the National Renewable Energy Laboratory (NREL) to perform monitoring of cogged V-belts and synchronous belts on both a constant volume and a variable air volume fan at the Byron G. Rodgers Federal Building and U.S. Courthouse in Denver, Colorado. These motor/fan combinations were tested with their original, standard V-belts (appropriately tensioned by an operation and maintenance professional) to obtain a baseline for standard operation. They were then switched to the cogged V-belts, and finally to synchronous belts. The power consumption by the motor was normalized for both fan speed and air density changes. This was necessary to ensure that the power readings were not influenced by a change in rotational fan speed or by the power required to push denser air. Finally, energy savings and operation and maintenance savings were compiled into an economic life-cycle cost analysis of the different belt options.

  15. A method to assess fluvial fan channel networks, with a preliminary application to fans in coastal British Columbia

    Science.gov (United States)

    Millard, Thomas Hugh; Hogan, Dan L.; Wilford, David J.; Roberts, Brian

    2010-03-01

    The channel network on a fluvial fan distributes sediment across the fan surface and determines fan development. We present a method to characterize fan channel networks (FCNs) so that the effect of controls (e.g., sediment supply) on the FCN can be evaluated. We then do a preliminary test of the method using three fans in coastal British Columbia. The method uses a set of three measures: 1) the spatial extent of hydrogeomorphic activity, measured as the percentage of the contemporary fan surface area occupied by active channels; 2) the topologic structure, using node counts to measure channel network complexity; and 3) a sediment budget to indicate the proportion of sediment that is stored on the fan, loosely characterized by comparing the second-largest clast size of sediment at the fan apex or intersection point with the second-largest clast at the toe of the fan. These measures were applied to two fan deltas and one partial fan delta in northern Vancouver Island, British Columbia, using channel surveys conducted in 2006 and 2007. All three fans are located within 30 km of each other, have similar climatic, physiographic, and vegetation settings, and have natural channel networks. Each fan has perennial channel flow at the fan apex. Watershed areas range from 19.5 to 35.6 km 2, and contemporary fan areas range from 0.2 to 0.7 km 2. The Melton Relative Relief ratio ranges from 0.24 to 0.30 and none of the fans show evidence of debris floods or debris flows. In addition to testing the efficacy of the FCN measures, we use these fans to explore the question of whether fans in similar geomorphic settings and with similar controls develop similar FCNs. Results show the fans have between 4.7-8.5 % of the contemporary fan surface occupied by the active channel network. Topologic node counts indicate that the two fan deltas have a similar level of channel complexity, with 42-54 nodes in total. The partial fan delta channel network is approximately half as complex, with

  16. Wordplay, mindplay: Fan fiction and postclassical narratology

    Directory of Open Access Journals (Sweden)

    Veerle Van Steenhuyse

    2014-09-01

    Full Text Available Recent narrative theories on story worlds, or the worlds evoked by narratives, call attention to the process of fan reading and the role which the canon plays in that process. This paper posits that such theories can help us understand literary techniques that make a difference on the level of the reading experience that is implied by fan fiction texts. This is illustrated with a close reading of Naguabo's "The Mother of All Marriage Proposals," a Jane Austen fic.

  17. Integral Compressor/Generator/Fan Unitary Structure

    OpenAIRE

    Dreiman, Nelik

    2016-01-01

    INTEGRAL COMPRESSOR / GENERATOR / FAN UNITARY STRUCTURE.*) Dr. Nelik Dreiman Consultant, P.O.Box 144, Tipton, MI E-mail: An extremely compact, therefore space saving single compressor/generator/cooling fan structure of short axial length and light weight has been developed to provide generation of electrical power with simultaneous operation of the compressor when power is unavailable or function as a regular AC compressor powered by a power line. The generators and ai...

  18. Fan affinity laws from a collision model

    CERN Document Server

    Bhattacharjee, Shayak

    2012-01-01

    The performance of a fan is usually estimated from hydrodynamical considerations. The calculations are long and involved and the results are expressed in terms of three affinity laws. In this work we use kinetic theory to attack this problem. A hard sphere collision model is used, and subsequently a correction to account for the flow behaviour of air is incorporated. Our calculations prove the affinity laws and provide numerical estimates of the air delivery, thrust and drag on a rotating fan.

  19. Aerodynamic modelling and optimization of axial fans

    Energy Technology Data Exchange (ETDEWEB)

    Noertoft Soerensen, Dan

    1998-01-01

    A numerically efficient mathematical model for the aerodynamics of low speed axial fans of the arbitrary vortex flow type has been developed. The model is based on a blade-element principle, whereby the rotor is divided into a number of annular stream tubes. For each of these stream tubes relations for velocity, pressure and radial position are derived from the conservation laws for mass, tangential momentum and energy. The equations are solved using the Newton-Raphson methods, and solutions converged to machine accuracy are found at small computing costs. The model has been validated against published measurements on various fan configurations, comprising two rotor-only fan stages, a counter-rotating fan unit and a stator-rotor stator stage. Comparisons of local and integrated properties show that the computed results agree well with the measurements. Optimizations have been performed to maximize the mean value of fan efficiency in a design interval of flow rates, thus designing a fan which operates well over a range of different flow conditions. The optimization scheme was used to investigate the dependence of maximum efficiency on 1: the number of blades, 2: the width of the design interval and 3: the hub radius. The degree of freedom in the choice of design variable and constraints, combined with the design interval concept, provides a valuable design-tool for axial fans. To further investigate the use of design optimization, a model for the vortex shedding noise from the trailing edge of the blades has been incorporated into the optimization scheme. The noise emission from the blades was minimized in a flow rate design point. Optimizations were performed to investigate the dependence of the noise on 1: the number of blades, 2: a constraint imposed on efficiency and 3: the hub radius. The investigations showed, that a significant reduction of noise could be achieved, at the expense of a small reduction in fan efficiency. (EG) 66 refs.

  20. The atomization and the flame structure in the combustion of residual fuel oils; La atomizacion y estructura de flama en la combustion de combustibles residuales

    Energy Technology Data Exchange (ETDEWEB)

    Bolado Estandia, Ramon [Instituto de Investigaciones Electricas, Cuernavaca (Mexico)

    1985-12-31

    In this article a research on the combustion of heavy residual fuel oils is presented. The type of flames studied were obtained by means of the burning of sprays produced by an atomizer designed and calibrated specially for the research purpose. The flame characteristics that were analyzed are its length, its luminosity, the temperature, the distribution of the droplets size and mainly the burning regime of the droplets in the flame. The experimental techniques that were used for these studies were shadow micro-photography, suction pyrometry and of total radiation, laser diffraction, 35 mm photography, and impact push. The analysis of the experimental results, together with the results of the application of a mathematical model, permitted to establish two parameters, that quantitatively related determine the burning regime of the droplets in a flame of sprays of residual heavy fuel oil. [Espanol] En este articulo se presenta una investigacion sobre la combustion de combustibles residuales pesados. El tipo de flamas estudiadas se obtuvieron mediante el quemado de sprays producidos por un atomizador disenado y calibrado especialmente para el proposito de la investigacion. Las caracteristicas de flama que se analizaron son la longitud, la luminosidad, la temperatura, la distribucion de tamano de gotas y, principalmente, el regimen de quemado de gotas en la flama. Las tecnicas experimentales que se usaron para estos estudios fueron microfotografia de sombras, pirometria de succion y de radiacion total, difraccion laser, fotografia de 35 mm y empuje de impacto. El analisis de resultados experimentales, junto con los resultados de la aplicacion de un modelo matematico, permitio establecer dos parametros, que relacionados cuantitativamente, determinan el regimen de quemado de gotas en una flama de sprays de combustible residual pesado.

  1. Fast emulsion-based method for simultaneous determination of Co, Cu, Pb and Se in crude oil, gasoline and diesel by graphite furnace atomic absorption spectrometry.

    Science.gov (United States)

    Luz, Maciel S; Nascimento, Angerson N; Oliveira, Pedro V

    2013-10-15

    A method for the simultaneous determination of Co, Cu, Pb and Se in crude oil, gasoline and diesel samples using emulsion-based sampling and GF AAS is proposed. 400mg of sample was weighted in volumetric flask following the sequential addition of 125 µL of hexane and 7.5 mL of Triton X-100(®) (20% mv(-1)). Subsequently, the mixture was stirred in ultrasonic bath, during 30 min, before dilution to 25 mL with deionized water. Aliquots of 20 μL of reference solution or sample emulsion were co-injected into the graphite tube with 10 μL of 2 g L(-1) Pd(NO3)2. The pyrolysis and atomization temperatures were 1300°C and 2250°C, respectively. The limits of detection (n=10, 3σ) and characteristic masses were 0.02 μg g(-1) (0.32 μg L(-1)) and 18 pg for Co, 0.03 μg g(-1) (0.48 μg L(-1)) and 15 pg for Cu, 0.04 μg g(-1) (0.64 μg L(-1)) and 48 pg for Pb, and 0.11 μg g(-1) (1.76 μg L(-1)) and 47 pg for Se. The reliabilities of the proposed method for Co and Se were checked by SRM(®) 1634c Residual Oil analysis. The found values are in accordance to the SRM at 95% confidence level (Student's t-test). Each sample was spiked with 0.18 μg g(-1) of Co, Cu, Pb and Se and the recoveries varied from 92% to 116% for Co, 83% to 117% for Cu, 72% to 117% for Pb, and 82% to 122% for Se.

  2. Radiated noise of ducted fans

    Science.gov (United States)

    Eversman, Walter

    The differences in the radiated acoustic fields of ducted and unducted propellers of the same thrust operating under similar conditions are investigated. An FEM model is created for the generation, propagation, and radiation of steady, rotor alone noise and exit guide vane interaction noise of a ducted fan. For a specified number of blades, angular mode harmonic, and rotor angular velocity, the acoustic field is described in a cylindrical coordinate system reduced to only the axial and radial directions. It is found that, contrary to the usual understanding of the Tyler and Sofrin (1962) result, supersonic tip speed rotor noise can be cut off if the tip Mach number is only slightly in excess of unity and if the number of blades is relatively small. If there are many blades, the fundamental angular mode number is large, and the Tyler and Sofrin result for thin annuli becomes more relevant. Shrouding of subsonic tip speed propellers is a very effective means of controlling rotor alone noise.

  3. The Connemara Fan: a major glacial grounding line fan west of Ireland

    Science.gov (United States)

    McCarron, Stephen; Praeg, Daniel; Monteys, Xavier; Scott, Gill

    2014-05-01

    Glacigenic topography on the mid-shelf (~130-350 m water depth) west of Galway, Ireland appears to have the morphological form, internal architecture and sediments associated with a large glacial grounding-line fan. Seismic data collected in 2009 and 2012 (during the GLAMAR and GATEWAYS 1 campaigns) reveal that the broad, arcuate ridges of the 'Olex moraine' form the landward part of a fan system which prograded beyond the mid-shelf break (defining the outer margin of the 'Clare Platform') westwards into the Porcupine Seabight. The topography is comparable to larger shelf-edge trough-mouth fans found further north along the same margin, however no discernible 'trough' has been identified on the Clare Platform. The ridge and fan topographic assemblage is renamed the 'Connemara Fan' in its entirety, based on its genetic relations and geographic location due west of Connemara, western Ireland. A macrofossil recovered from within a debris flow on the outer fan slope comprised of remobilised plumites dates to ~ 20 ka Cal B.P., indicating sediment reworking downslope following deglacial sediment input to at least that time. The Connemara Fan is the most southerly glacigenic fan identified along the north-east Atlantic margin. Its identification also adds to our knowledge of possibly multiple generations of ice sheets feeding onto the Irish shelf from west-central Ireland and the occurrence of ice sheet geometries and dynamics that evacuated ice, melt-water and sediment (ice streams?) westwards across the Clare Platform during past glaciations.

  4. Fan relationship management in football - going beyond traditional product offerings to win the hearts of fans

    DEFF Research Database (Denmark)

    Cortsen, Kenneth

    2015-01-01

    The management and control of fan relations should go beyond a football club’s traditional product and service offerings and touch the important experiential side of the football economy. This will create a stronger platform to optimize ROI, ROE and ROO relating to different fan segments....

  5. Novel Crosstalk Measurement Method for Multi-Core Fiber Fan-In/Fan-Out Devices

    DEFF Research Database (Denmark)

    Ye, Feihong; Ono, Hirotaka; Abe, Yoshiteru;

    2016-01-01

    We propose a new crosstalk measurement method for multi-core fiber fan-in/fan-out devices utilizing the Fresnel reflection. Compared with the traditional method using core-to-core coupling between a multi-core fiber and a single-mode fiber, the proposed method has the advantages of high reliabili...

  6. Evaluation of cadmium, lead, copper, iron and zinc in Turkish dietary vegetable oils and olives using electrothermal and flame atomic absorption spectrometry

    Directory of Open Access Journals (Sweden)

    Acar, Orhan

    2012-10-01

    Full Text Available The Cd, Pb, Cu, Fe and Zn contents of some edible vegetable oils (soybean, sunflower, flower, nut, corn and olive and of olives (olive-1, black, green, black crushed with seeds and green crushed with seeds were determined and evaluated by an electrothermal atomic absorption spectrometer (ETAAS using an Sc + Ir + NH4H2PO4 chemical modifier mixture and flame atomic absorption spectrometer (FAAS after microwave digestion. The pyrolysis and atomization temperatures of Cd, Pb and Cu in sample solutions with and without the modifier mixture were investigated. The limits of detection (LOD for analytes found are 0.1, 0.6, 0.9, 15.0 and 12.0 μg L–1 for Cd, Cu, Pb, Fe and Zn, respectively. The accuracy of the procedure proposed was confirmed by analyzing bovine liver 1577b standard reference material (SRM and a spiked sample solution. The results of the analytes found were compared with certified and added values. The relative standard deviations of the analytes found were lower than 7% and the percent of recoveries obtained ranges from 96 to 101%. The Sc + Ir + NH4H2PO4 mixture proposed was applied for the determination of Cd, Pb and Cu in oils and olives. The results of analytes found in the samples were compared with international and national food quality guidelines as well as with literature values.

    Se han determinado los metales Cd, Cu, Pb, Fe y Zn en aceites vegetales comestibles (soja, girasol, flores, nueces, maíz y aceite de oliva y aceitunas (aceitunas-1, negra, verde, negra machacadas con semillas y verde machacadas con semillas mediante espectrometría de absorción atómica electrotérmica (ETAAS utilizando como modificador químico la mezcla Sc + Ir + NH4H2PO4 y mediante espectrometría de absorción atómica de llama (FAAS tras digestión con microondas. Se estudiaron las temperaturas de pirólisis y atomización para Cd

  7. Design Guidelines for Quiet Fans and Pumps for Space Vehicles

    Science.gov (United States)

    Lovell, John S.; Magliozzi, Bernard

    2008-01-01

    This document presents guidelines for the design of quiet fans and pumps of the class used on space vehicles. A simple procedure is presented for the prediction of fan noise over the meaningful frequency spectrum. A section also presents general design criteria for axial flow fans, squirrel cage fans, centrifugal fans, and centrifugal pumps. The basis for this report is an experimental program conducted by Hamilton Standard under NASA Contract NAS 9-12457. The derivations of the noise predicting methods used in this document are explained in Hamilton Standard Report SVHSER 6183, "Fan and Pump Noise Control," dated May 1973 (6).

  8. Numerical Aerodynamic Evaluation and Noise Investigation of a Bladeless Fan

    OpenAIRE

    mohammad jafari; Hossein Afshin; Bijan Farhanieh; Hamidreza bozorgasareh

    2015-01-01

    Bladeless fan is a novel fan type that has no observable impeller, usually used for domestic applications. Numerical investigation of a Bladeless fan via Finite Volume Method was carried out in this study. The fan was placed in center of a 4×2×2m room and 473 Eppler airfoil profile was used as cross section of the fan. Performance and noise level of the fan by solving continuity and momentum equations as well as noise equations of Broadband Noise Source (BNS) and Ffowcs Williams a...

  9. Soybean oil and methyl oleate adsorption onto a steel surface investigated using a quartz crystal microbalance with dissipation monitoring and atomic force microscopy**1

    Science.gov (United States)

    The United States’ 2010 annual production of soybean oil exceeded 8 million metric tons, making a significant vegetable oil surplus available for new uses, particularly as a lubricant. Investigation of soybean oil and methyl oleate adsorption onto steel using a quartz crystal microbalance with diss...

  10. Optimism Bias in Fans and Sports Reporters.

    Directory of Open Access Journals (Sweden)

    Bradley C Love

    Full Text Available People are optimistic about their prospects relative to others. However, existing studies can be difficult to interpret because outcomes are not zero-sum. For example, one person avoiding cancer does not necessitate that another person develops cancer. Ideally, optimism bias would be evaluated within a closed formal system to establish with certainty the extent of the bias and the associated environmental factors, such that optimism bias is demonstrated when a population is internally inconsistent. Accordingly, we asked NFL fans to predict how many games teams they liked and disliked would win in the 2015 season. Fans, like ESPN reporters assigned to cover a team, were overly optimistic about their team's prospects. The opposite pattern was found for teams that fans disliked. Optimism may flourish because year-to-year team results are marked by auto-correlation and regression to the group mean (i.e., good teams stay good, but bad teams improve.

  11. Optimism Bias in Fans and Sports Reporters.

    Science.gov (United States)

    Love, Bradley C; Kopeć, Łukasz; Guest, Olivia

    2015-01-01

    People are optimistic about their prospects relative to others. However, existing studies can be difficult to interpret because outcomes are not zero-sum. For example, one person avoiding cancer does not necessitate that another person develops cancer. Ideally, optimism bias would be evaluated within a closed formal system to establish with certainty the extent of the bias and the associated environmental factors, such that optimism bias is demonstrated when a population is internally inconsistent. Accordingly, we asked NFL fans to predict how many games teams they liked and disliked would win in the 2015 season. Fans, like ESPN reporters assigned to cover a team, were overly optimistic about their team's prospects. The opposite pattern was found for teams that fans disliked. Optimism may flourish because year-to-year team results are marked by auto-correlation and regression to the group mean (i.e., good teams stay good, but bad teams improve).

  12. ANALYTICAL METHODS FOR CALCULATING FAN AERODYNAMICS

    Directory of Open Access Journals (Sweden)

    Jan Dostal

    2015-12-01

    Full Text Available This paper presents results obtained between 2010 and 2014 in the field of fan aerodynamics at the Department of Composite Technology at the VZLÚ aerospace research and experimental institute in Prague – Letnany. The need for rapid and accurate methods for the preliminary design of blade machinery led to the creation of a mathematical model based on the basic laws of turbomachine aerodynamics. The mathematical model, the derivation of which is briefly described below, has been encoded in a computer programme, which enables the theoretical characteristics of a fan of the designed geometry to be determined rapidly. The validity of the mathematical model is assessed continuously by measuring model fans in the measuring unit, which was developed and manufactured specifically for this purpose. The paper also presents a comparison between measured characteristics and characteristics determined by the mathematical model as the basis for a discussion on possible causes of measured deviations and calculation deviations.

  13. Fan Noise Source Diagnostic Test: Rotor Alone Aerodynamic Performance Results

    Science.gov (United States)

    Hughes, Christopher E.; Jeracki, Robert J.; Woodward, Richard P.; Miller, Christopher J.

    2005-01-01

    The aerodynamic performance of an isolated fan or rotor alone model was measured in the NASA Glenn Research Center 9- by 15- Foot Low Speed Wind Tunnel as part of the Fan Broadband Source Diagnostic Test conducted at NASA Glenn. The Source Diagnostic Test was conducted to identify the noise sources within a wind tunnel scale model of a turbofan engine and quantify their contribution to the overall system noise level. The fan was part of a 1/5th scale model representation of the bypass stage of a current technology turbofan engine. For the rotor alone testing, the fan and nacelle, including the inlet, external cowl, and fixed area fan exit nozzle, were modeled in the test hardware; the internal outlet guide vanes located behind the fan were removed. Without the outlet guide vanes, the velocity at the nozzle exit changes significantly, thereby affecting the fan performance. As part of the investigation, variations in the fan nozzle area were tested in order to match as closely as possible the rotor alone performance with the fan performance obtained with the outlet guide vanes installed. The fan operating performance was determined using fixed pressure/temperature combination rakes and the corrected weight flow. The performance results indicate that a suitable nozzle exit was achieved to be able to closely match the rotor alone and fan/outlet guide vane configuration performance on the sea level operating line. A small shift in the slope of the sea level operating line was measured, which resulted in a slightly higher rotor alone fan pressure ratio at take-off conditions, matched fan performance at cutback conditions, and a slightly lower rotor alone fan pressure ratio at approach conditions. However, the small differences in fan performance at all fan conditions were considered too small to affect the fan acoustic performance.

  14. Miocene Current-Modified Submarine Fans

    Science.gov (United States)

    Arce Perez, L. E.; Snedden, J.; Fisher, W. L.

    2016-12-01

    In the southwestern Gulf of Mexico, new and newly reprocessed seismic data has revealed a series of large bedforms, with set thicknesses of 130 to 250 meters. These exhibit hummocky, oblique and shingled to parallel seismic clinoform reflections. This seismic package has a paleowater depth of 450 meters. Those shingled seismic reflections in offshore east Mexico are interpreted as contourite drift deposits. These Miocene-age contourites may be related to strong ocean bottom currents that modified submarine fans and transported sediment to the north. Those contourites were identified on older seismic data, but are better imaged and interpreted on this new data. Plans are to map out and investigate the origin and extent of fans and contourites that extends over a large area of the Gulf of Mexico. In the Early Miocene several submarine fans systems were formed by the sediment input related to orogenic activity in Mexico. Submarine fan development persisted into the Middle Miocene due to continued uplift and erosion of the Mexican landmass. Initial, contourites are small and close proximity to the deep-water fan. In the Late Miocene time, contourite drift field reached its maximum extent in the Mexican deepwater area, anchored on its southern end by a submarine mound. This mounded submarine fan is located in the offshore northeast Veracruz and can be linked to increased uplift and erosion of the Trans-Mexican volcanic belt. In the Miocene-Pliocene, the large contourite drift begins to diminish in size and scale and is moribund by the Pliocene, with establishment of oceanic circulation similar to the present day. This research is important to understand more about the Gulf of Mexico and also for the Miocene timeframe that is a key phase in the earth's history. The role of the change in bottom water flow during progressive closure of the equatorial seaway separating North and South America will also be investigated.

  15. Experimental alluvial fans: Advances in understanding of fan dynamics and processes

    Science.gov (United States)

    Clarke, Lucy E.

    2015-09-01

    Alluvial fans are depositional systems that develop because of a disparity between the upstream and downstream sediment transport capacity of a system, usually at the base of mountain fronts as rivers emerge from the constrained mountain area onto the plain. They are dynamic landforms that are prone to abrupt changes on a geomorphological (decades to centuries) time scale, while also being long-term deposition features that preserve sedimentary strata and are sensitive indictors of environmental change. The complexity of interactions between catchment characteristics, climate, tectonics, internal system feedbacks, and environmental processes on field alluvial fans means that it is difficult to isolate individual variables in a field setting; therefore, the controlled conditions afforded by experimental models has provided a novel technique to overcome some of these complexities. The use of experimental models of alluvial fans has a long history and these have been implemented over a range of different research areas utilising various experimental designs. Using this technique, important advances have been made in determining the primary factors influencing fan slope, understanding of avulsion dynamics, identifying autogenic processes driving change on fan systems independent of any change in external conditions, and the mechanics of flow and flood risk on alluvial fans, to name a few. However, experiments cannot be carried out in isolation. Thus, combining the findings from experimental alluvial fans with field research and numerical modelling is important and, likewise, using these techniques to inform experimental design. If this can be achieved, there is potential for future experimental developments to explore key alluvial fan issues such as stratigraphic preservation potential and simulating extra terrestrial fan systems.

  16. Homophobia, heteronormativity, and slash fan fiction

    Directory of Open Access Journals (Sweden)

    April S. Callis

    2016-09-01

    Full Text Available I analyze the relationship between homophobia/heteronormativity and slash fan fiction. Through reading and coding almost 6,000 pages of Kirk/Spock fan fiction written from 1978 to 2014, I illuminate shifts in how normative gender and sexuality are portrayed by K/S authors. Writers of K/S, while ostensibly writing about the 23rd century, consciously or unconsciously include cultural norms from the 20th and 21st centuries. Thus, slash becomes a lens through which readers can view a decrease in both homophobia and heteronormativity in US culture over the past several decades.

  17. Fan fiction metadata creation and utilization within fan fiction archives: Three primary models

    Directory of Open Access Journals (Sweden)

    Shannon Fay Johnson

    2014-09-01

    Full Text Available Issues related to searchability and ease of access have plagued fan fiction since its inception. This paper discusses the predominate forms of fan-mediated indexing and descriptive metadata, commonly referred to as folksonomy or tagging, and compares the benefits and disadvantages of each model. These models fall into three broad categories: free tagging, controlled vocabulary, and hybrid folksonomy. Each model has distinct advantages and shortcomings related to findability, results filtering, and creative empowerment. Examples for each are provided. Possible ramifications to fan fiction from improved metadata and access are also discussed.

  18. Experiencing fan activism: Understanding the power of fan activist organizations through members' narratives

    Directory of Open Access Journals (Sweden)

    Neta Kligler-Vilenchik

    2012-06-01

    Full Text Available Fan activism, forms of civic engagement and political participation growing out of experiences of fandom, is a powerful mode of mobilization, particularly for young people. Building on 40 interviews with members of two organizations representing different configurations of fan activism, this article discusses three emerging elements that are key to the experience of membership in such groups. We suggest that the strength of fan activist groups builds on successfully combining these elements: two that are common to fandom, shared media experiences and a sense of community, and one that is traditionally ascribed to volunteerism and activism, the wish to help.

  19. Alluvial Fan Study Submission for UMATILLA COUNTY, OREGON

    Data.gov (United States)

    Federal Emergency Management Agency, Department of Homeland Security — Alluvial fan study data as defined in FEMA Guidelines and Specifications, Appendix G: Guidance for Alluvial Fan Flooding Analyses and Mapping

  20. Improving Fan System Performance: A Sourcebook for Industry

    Energy Technology Data Exchange (ETDEWEB)

    None

    2003-04-01

    This is one of a series of sourcebooks on motor-driven equipment produced by the Industrial Technologies Program. It provides a reference for industrial fan systems users, outlining opportunities to improve fan system performance.

  1. Fan action and political participation on "The Colbert Report"

    Directory of Open Access Journals (Sweden)

    Marcus Schulzke

    2012-06-01

    Full Text Available The Colbert Report merges the increasingly popular political satire genre with fan activism. The result is that the fan community helps to construct Colbert's malleable character and demonstrates symbolic power through its willingness to act. The fans are usually a nonpartisan force, acting to produce entertainment rather than substantive political change. However, this can be politically meaningful, as the fans' projects promote collective action, parallel political activities like voting and protesting, and encourage critical thinking about political information.

  2. Dead links, vaporcuts, and creativity in fan edit replication

    Directory of Open Access Journals (Sweden)

    Joshua Wille

    2015-09-01

    Full Text Available In my examination of a Star Wars prequel trilogy fan edit reportedly made by Topher Grace, I introduce the term vaporcut to describe fan edits with reputations that may generate critical discourse but that are not publicly released. I explore the ways some fan editors attempt to recreate intangible projects but inevitably produce variant works that reflect their own creative perspectives.

  3. Star Trek Rerun, Reread, Rewritten: Fan Writing as Textual Poaching.

    Science.gov (United States)

    Jenkins III, Henry

    1988-01-01

    Discusses women who write fiction and fan literature based on the "Star Trek" universe, outlining how Star Trek fans force the primary text to accommodate alternate interests. Also considers the issue of literary property in light of the moral economy of the fan community that shapes the range of permissible retellings of the program…

  4. Fan Stall Flutter Flow Mechanism Studied

    Science.gov (United States)

    Lepicovsky, Jan

    2002-01-01

    Modern turbofan engines employ a highly loaded fan stage with transonic or low-supersonic velocities in the blade-tip region. The fan blades are often prone to flutter at off-design conditions. Flutter is a highly undesirable and dangerous self-excited mode of blade oscillations that can result in high-cycle fatigue blade failure. The origins of blade flutter are not fully understood yet. Experimental data that can be used to clarify the origins of blade flutter in modern transonic fan designs are very limited. The Transonic Flutter Cascade Facility at the NASA Glenn Research Center was developed to experimentally study the details of flow mechanisms associated with fan flutter. The cascade airfoils are instrumented to measure high-frequency unsteady flow variations in addition to the steady flow data normally recorded in cascade tests. The test program measures the variation in surface pressure in response to the oscillation of one or more of the cascade airfoils. However, during the initial phases of the program when all airfoils were in fixed positions, conditions were found where significant time variations in the pressures near the airfoil leading edges could be observed.

  5. Acoustic analysis of a computer cooling fan

    Science.gov (United States)

    Huang, Lixi; Wang, Jian

    2005-10-01

    Noise radiated by a typical computer cooling fan is investigated experimentally and analyzed within the framework of rotor-stator interaction noise using point source formulation. The fan is 9 cm in rotor casing diameter and its design speed is 3000 rpm. The main noise sources are found and quantified; they are (a) the inlet flow distortion caused by the sharp edges of the incomplete bellmouth due to the square outer framework, (b) the interaction of rotor blades with the downstream struts which hold the motor, and (c) the extra size of one strut carrying electrical wiring. Methods are devised to extract the rotor-strut interaction noise, (b) and (c), radiated by the component forces of drag and thrust at the leading and higher order spinning pressure modes, as well as the leading edge noise generated by (a). By re-installing the original fan rotor in various casings, the noises radiated by the three features of the original fan are separated, and details of the directivity are interpreted. It is found that the inlet flow distortion and the unequal set of four struts make about the same amount of noise. Their corrections show a potential of around 10-dB sound power reduction.

  6. Generalized sorting profile of alluvial fans

    Science.gov (United States)

    Miller, Kimberly Litwin; Reitz, Meredith D.; Jerolmack, Douglas J.

    2014-10-01

    Alluvial rivers often exhibit self-similar gravel size distributions and abrupt gravel-sand transitions. Experiments suggest that these sorting patterns are established rapidly, but how—and how fast—this convergence occurs in the field is unknown. We examine the establishment of downstream sorting patterns in a kilometer-scale alluvial fan. The sharp transition from canyon to unconfined, channelized fan provides a well-defined boundary condition. The channel changes from deep and entrenched at the fan apex to shallow and depositional over a short distance, exhibiting nonequilibrium behavior. The resulting gravel-fining profile is not self-similar; the particle size distribution narrows until approximate equal mobility is achieved. Downfan, the gravel-sand transition appears to exhibit a self-similar form; field and laboratory data collapse when downstream distance is normalized by the location of the transition. Results suggest a generalized sorting profile for alluvial fans as a consequence of the threshold of motion and nonequilibrium channels.

  7. Fan Affinity Laws from a Collision Model

    Science.gov (United States)

    Bhattacharjee, Shayak

    2012-01-01

    The performance of a fan is usually estimated using hydrodynamical considerations. The calculations are long and involved and the results are expressed in terms of three affinity laws. In this paper we use kinetic theory to attack this problem. A hard sphere collision model is used, and subsequently a correction to account for the flow behaviour…

  8. Test particle acceleration in torsional fan reconnection

    Science.gov (United States)

    Hosseinpour, M.

    2014-12-01

    Magnetic reconnection is understood to be a potential mechanism for particle acceleration in astrophysical and space plasmas, especially in solar flares. Torsional fan reconnection is one of the proposed mechanisms for steady-state three-dimensional (3D) magnetic reconnection. By using the magnetic and electric fields for `torsional fan reconnection', the features of test particle acceleration with input parameters for the solar corona are investigated numerically. We show that torsional fan reconnection is potentially an efficient particle accelerator and a proton can gain up to tens of MeV of kinetic energy within only a few milliseconds. Although the final kinetic energy of the accelerated particle depends on the injection position but there exists only one scenario for the particle's trajectory with different initial positions in which the particle is accelerated on the fan plane. Moreover, adopting either spatially uniform or non-uniform localized plasma resistivity does not much influence the features of trajectory. These results are compared with those of torsional spine reconnection.

  9. Fan Affinity Laws from a Collision Model

    Science.gov (United States)

    Bhattacharjee, Shayak

    2012-01-01

    The performance of a fan is usually estimated using hydrodynamical considerations. The calculations are long and involved and the results are expressed in terms of three affinity laws. In this paper we use kinetic theory to attack this problem. A hard sphere collision model is used, and subsequently a correction to account for the flow behaviour…

  10. Fan Ky不等式的一个新改进%A New Improvement of Fan Ky's Inequality

    Institute of Scientific and Technical Information of China (English)

    黄政; 高明哲; 徐景实

    2010-01-01

    利用Gram矩阵的正定性和可变单位向量建立了Fan Ky不等式的一个新的改进,并且建立了反向Fan Ky不等式.对于非奇异矩阵,得到了Fan Ky不等式以及反向Fan Ky不等式的推广.

  11. Regenerative Blower for EVA Suit Ventilation Fan

    Science.gov (United States)

    Izenson, Michael G.; Chen, Weibo; Paul, Heather L.

    2010-01-01

    Portable life support systems in future space suits will include a ventilation subsystem driven by a dedicated fan. This ventilation fan must meet challenging requirements for pressure rise, flow rate, efficiency, size, safety, and reliability. This paper describes research and development that showed the feasibility of a regenerative blower that is uniquely suited to meet these requirements. We proved feasibility through component tests, blower tests, and design analysis. Based on the requirements for the Constellation Space Suit Element (CSSE) Portable Life Support System (PLSS) ventilation fan, we designed the critical elements of the blower. We measured the effects of key design parameters on blower performance using separate effects tests, and used the results of these tests to design a regenerative blower that will meet the ventilation fan requirements. We assembled a proof-of-concept blower and measured its performance at sub-atmospheric pressures that simulate a PLSS ventilation loop environment. Head/flow performance and maximum efficiency point data were used to specify the design and operating conditions for the ventilation fan. We identified materials for the blower that will enhance safety for operation in a lunar environment, and produced a solid model that illustrates the final design. The proof-of-concept blower produced the flow rate and pressure rise needed for the CSSE ventilation subsystem while running at 5400 rpm, consuming only 9 W of electric power using a non-optimized, commercial motor and controller and inefficient bearings. Scaling the test results to a complete design shows that a lightweight, compact, reliable, and low power regenerative blower can meet the performance requirements for future space suit life support systems.

  12. Psychoacoustic study on contribution of fan noise to engine noise

    Science.gov (United States)

    Zhang, Junhong; Liu, Hai; Bi, Fengrong; Ni, Guangjian; Zhang, Guichang; Lin, Jiewei; Yu, Hanzhengnan

    2012-07-01

    There are more researches on engine fan noise control focusing on reducing fan noise level through optimizing fan structure, and a lot of research achievements have been obtained. However, researches on the effect of fan noise to engine noise quality are lacking. The influences of the effects of fan structure optimization on the engine noise quality are unclear. Thus, there will be a decline in fan noise level, but the deterioration of engine noise quality. Aiming at the above problems, in consideration of fan structure design and engine noise quality, an innovative method to analyze the contribution of fan noise to engine noise quality using psychoacoustic theory is proposed. The noises of diesel engine installing different cooling fans are measured by using the acoustic pressure method. The experiment results are regarded as analysis samples. The model of sensory pleasantness is used to analyze the sound quality of a diesel engine with different cooling fans. Results show that after installing 10-blade fan in medium diameter the sensory pleasantness at each test point is increased, and the increase is 13.53% on average, which indicate the improvement of the engine noise quality. In order to verify the psychoacoustical analysis, the subjective assessment is carried out. The test result shows the noise quality of engine installed 10-blade fan in medium diameter is most superior. 1/3 octave frequency spectrum analysis is used to study the reason of the improvement of engine noise quality. It is found that after installing proper cooling fan the sound pressure level below 400 Hz are obviously increased, the frequency assignment and spectral envelope are more reasonable and a proper cooling fan can optimize the spectrum structure of the engine noise. The psychoacoustic study is applied in the contribution of fan noise to engine noise, and the idea of engine sound quality improvement through the structure optimization is proposed.

  13. Introduction of a Cooling-Fan Efficiency Index

    DEFF Research Database (Denmark)

    Schiavon, S.; Melikov, Arsen Krikor

    2009-01-01

    In a warm environment, air movement with elevated velocity is a well-known cooling strategy. The local air movement is typically generated by cooling fans (e.g., ceiling fan, table fans, etc.). Appearance, power input, and price are the main parameters considered today when purchasing cooling fans......, while cooling capacity and efficiency of energy use are unknown. To address this knowledge gap, this paper introduces the cooling-fan efficiency (CFE) index, defined as the ratio between the cooling effect (measured with a thermal manikin) generated by the device and its power consumption. The index...

  14. Investigation and numerical simulation of inner-flow of an axial mineflow fan under low flow rate conditions

    Institute of Scientific and Technical Information of China (English)

    LI Yi-min; ZHOU Zhong-ning

    2008-01-01

    Because of unstable properties of axial mine flow fans working under conditions of low flow rates, the safety and reli-ability of fans in their operational zone is reduced. At times, serious vibration may bring about the destruction of equipment or even jeopardize the safety of entire factories. By means of oil flow visualization techniques and numerical simulation, we have investi-gated the inner-flow of an axial mine flow fan working under low flow rate conditions. The fundamental reasons of complex flow phenomena of the inner-flow of the flow fan under these stated conditions were revealed. At the same time and in order to improve the inner-flow under conditions of low flow rates, a blade separator and air separator were designed. From our tests we found that the blade separator and air separator are two kinds efficient methods to improve the unstable working characteristics of the axial mine flow fan operating under low flow rate conditions. The effect of the improvement of the air separator is stronger than that of the blade separator.

  15. Fan-beam intensity modulated proton therapy

    Science.gov (United States)

    Hill, Patrick; Westerly, David; Mackie, Thomas

    2013-01-01

    Purpose: This paper presents a concept for a proton therapy system capable of delivering intensity modulated proton therapy using a fan beam of protons. This system would allow present and future gantry-based facilities to deliver state-of-the-art proton therapy with the greater normal tissue sparing made possible by intensity modulation techniques. Methods: A method for producing a divergent fan beam of protons using a pair of electromagnetic quadrupoles is described and particle transport through the quadrupole doublet is simulated using a commercially available software package. To manipulate the fan beam of protons, a modulation device is developed. This modulator inserts or retracts acrylic leaves of varying thickness from subsections of the fan beam. Each subsection, or beam channel, creates what effectively becomes a beam spot within the fan area. Each channel is able to provide 0–255 mm of range shift for its associated beam spot, or stop the beam and act as an intensity modulator. Results of particle transport simulations through the quadrupole system are incorporated into the MCNPX Monte Carlo transport code along with a model of the range and intensity modulation device. Several design parameters were investigated and optimized, culminating in the ability to create topotherapy treatment plans using distal-edge tracking on both phantom and patient datasets. Results: Beam transport calculations show that a pair of electromagnetic quadrupoles can be used to create a divergent fan beam of 200 MeV protons over a distance of 2.1 m. The quadrupole lengths were 30 and 48 cm, respectively, with transverse field gradients less than 20 T/m, which is within the range of water-cooled magnets for the quadrupole radii used. MCNPX simulations of topotherapy treatment plans suggest that, when using the distal edge tracking delivery method, many delivery angles are more important than insisting on narrow beam channel widths in order to obtain conformal target coverage

  16. Characterization of Composite Fan Case Resins

    Science.gov (United States)

    Dvoracek, Charlene M.

    2004-01-01

    The majority of commercial turbine engines that power today s aircraft use a large fan driven by the engine core to generate thrust which dramatically increases the engine s efficiency. However, if one of these fan blades fails during flight, it becomes high energy shrapnel, potentially impacting the engine or puncturing the aircraft itself and thus risking the lives of passengers. To solve this problem, the fan case must be capable of containing a fan blade should it break off during flight. Currently, all commercial fan cases are made of either just a thick metal barrier or a thinner metal wall surrounded by Kevlar-an ultra strong fiber that elastically catches the blade. My summer 2004 project was to characterize the resins for a composite fan case that will be lighter and more efficient than the current metal. The composite fan case is created by braiding carbon fibers and injecting a polymer resin into the braid. The resin holds the fibers together, so at first using the strongest polymer appears to logically lead to the strongest fan case. Unfortunately, the stronger polymers are too viscous when melted. This makes the manufacturing process more difficult because the polymer does not flow as freely through the braid, and the final product is less dense. With all of this in mind, it is important to remember that the strength of the polymer is still imperative; the case must still contain blades with high impact energy. The research identified which polymer had the right balance of properties, including ease of fabrication, toughness, and ability to transfer the load to the carbon fibers. Resin deformation was studied to better understand the composite response during high speed impact. My role in this research was the testing of polymers using dynamic mechanical analysis and tensile, compression, and torsion testing. Dynamic mechanical analysis examines the response of materials under cyclic loading. Two techniques were used for dynamic mechanical analysis

  17. Improvement in performance of main ventilation fan for mines

    Energy Technology Data Exchange (ETDEWEB)

    Mukherjee, S.N. [Indian School of Mines, Dhanbad (India)

    2007-07-01

    This paper examined methods of improving the performance of main ventilation fans in mines. The basic principles of selecting and operating fans were reviewed, and methods of improving the energy efficiency of fans were evaluated. The study considered issues related to static efficiency, as well as curves and intersection points. Mine resistances were examined in relation to ventilation requirements at different phases of mine development. Flow losses and difficulties in producing accurate mathematical models of ventilation fans were also discussed. Fan operation set-points were reviewed. Details of tests conducted to determine the effects of the number of blades on fan performance were presented. The tests demonstrated the importance of incorporating cowl diffusers and guide vanes within the design of axial flow fans. The advantages of deblading were also discussed. 6 refs.

  18. Fluent-based numerical simulation of flow centrifugal fan

    Institute of Scientific and Technical Information of China (English)

    LI Xian-zhang

    2011-01-01

    Testing centrifugal fan flow field by physical laboratory is difficult because the testing system is complex and the workload is heavy, and the results observed by naked-eye deviates far from the actual value. To address this problem, the computational fluid dynamics software FLUENT was applied to establish three-dimensional model of the centrifugal fan. The numeral model was verified by comparing simulation data to experimental data. The pressure centrifugal fan and the speed changes in distribution in centrifugal fan was simulated by computational fluid dynamics software FLUENT. The simulation results show that the gas flow velocity in the impeller increases with impeller radius increase. Static pressure gradually increases when gas from the fan access is imported through fan impeller leaving fans.

  19. Numerical Aerodynamic Evaluation and Noise Investigation of a Bladeless Fan

    Directory of Open Access Journals (Sweden)

    mohammad jafari

    2015-01-01

    Full Text Available Bladeless fan is a novel fan type that has no observable impeller, usually used for domestic applications. Numerical investigation of a Bladeless fan via Finite Volume Method was carried out in this study. The fan was placed in center of a 4×2×2m room and 473 Eppler airfoil profile was used as cross section of the fan. Performance and noise level of the fan by solving continuity and momentum equations as well as noise equations of Broadband Noise Source (BNS and Ffowcs Williams and Hawkings (FW-H in both steady state and unsteady conditions were studied. Flow increase ratio of the fan was captured. Furthermore, BNS method could find outlet slit of the air as the main source of the noise generation. In order to validation of aeroacousticcode results, a simulation of noise for NACA 0012 airfoil via FW-H method was compared to experimental results and good agreement was obtained.

  20. Nocturnal Fanning Suppresses Downy Mildew Epidemics in Sweet Basil.

    Science.gov (United States)

    Cohen, Yigal; Ben-Naim, Yariv

    2016-01-01

    Downy mildew is currently the most serious disease of sweet basil around the world. The oomycete causal agent Peronospora belbahrii requires ≥ 4h free leaf moisture for infection and ≥7.5h of water-saturated atmosphere (relative humidity RH≥95%) at night for sporulation. We show here that continued nocturnal fanning (wind speed of 0.4-1.5 m/s) from 8pm to 8am dramatically suppressed downy mildew development. In three experiments conducted during 2015, percent infected leaves in regular (non-fanned) net-houses reached a mean of 89.9, 94.3 and 96.0% compared to1.2, 1.7 and 0.5% in adjacent fanned net-houses, respectively. Nocturnal fanning reduced the number of hours per night with RH≥95% thus shortened the dew periods below the threshold required for infection or sporulation. In experiments A, B and C, the number of nights with ≥4h of RH≥95% was 28, 10 and 17 in the non-fanned net-houses compared to 5, 0 and 5 in the fanned net-houses, respectively. In the third experiment leaf wetness sensors were installed. Dew formation was strongly suppressed in the fanned net-house as compared to the non-fanned net-house. Healthy potted plants became infected and sporulated a week later if placed one night in the non-fanned house whereas healthy plants placed during that night in the fanned house remained healthy. Infected potted basil plants sporulated heavily after one night of incubation in the non-fanned house whereas almost no sporulation occurred in similar plants incubated that night in the fanned house. The data suggest that nocturnal fanning is highly effective in suppressing downy mildew epidemics in sweet basil. Fanning prevented the within-canopy RH from reaching saturation, reduced dew deposition on the leaves, and hence prevented both infection and sporulation of P. belbahrii.

  1. Deep-water Fan Systems and Petroleum Resources on the Northern Slope of the South China Sea

    Institute of Scientific and Technical Information of China (English)

    PANG Xiong; YANG Shaokun; ZHU Ming; LI Jinsong

    2004-01-01

    The shallow shelf delta/strand arenaceous-pelitic deposit region in the north of the Pearl River mouth basin,sitting on the northern continental shelf of the South China Sea, has already become an important oil production base in China. Recent researched has revealed that a great deal of deep-water fans of great petroleum potentiality exist on the Baiyun deep-water slope below the big palco Pearl River and its large delta. Based on a mass of exploration wells and 2-D seismic data of the shallow shelf region, a interpretation of sequence stratigraphy confirmed the existence of deep-water fans. The cyclic falling of sea level, abundant detrital matter from the paleo Pearl River and the persistent geothermal subsidence in the Baiyun sag are the three prerequisites for the formation and development of deep-water fans. There are many in common between the deep-water shelf depositional system of the northern South China Sea and the exploration hotspots region on the two banks of the Atlantic. For example, both are located on passive continent margins, and persistent secular thermal subsidence and large palco rivers have supplied abundant material sources and organic matter.More recently, the discovery of the big gas pool on the northern slope of the Baiyun sag confirms that the Lower Tertiary lacustrine facies in the Baiyun sag has a great potentiality of source rocks. The fans overlying the Lower Tertiary source rocks should become the main exploration areas for oil and gas resources.

  2. Comparison of turbidite facies associations in modern passive-margin Mississippi fan with ancient active-margin fans

    Science.gov (United States)

    Shanmugam, G.; Moiola, R. J.; McPherson, J. G.; O'Connell, S.

    1988-07-01

    Our comparison of the modern passive-margin Mississippi fan (DSDP Leg 96) with ancient active-margin fans (e.g. Eocene Hecho Group, Spain) reveals major differences in turbidite facies associations (Mutti and Ricci Lucchi scheme) and in seismic characteristics in the lower fan area. The lower (outer) Mississippi fan is composed of channel (Facies B and F) and non-channel facies (C? and D), whereas ancient fans are characterized by non-channelized, thickening-upward, depositional lobe facies (C and D). An absence of depositional lobes in the lower Mississippi fan is also suggested by a lack of convex-upward (mounded) seismic reflections with bidirectional downlap. Continuous seismic reflections of the lower Mississippi fan may represent "sheet sands", but not those of true depositional lobes with mounded character. Extensive channelization in modern passive-margin fans appears to be a product of the lateral shifting of a major sinuous distributary system, developed as a consequence of low gradients and the transport of sediment with a relatively low sand/mud ratio. In contrast, channels in active-margin fans are short and of low sinuosity as a result of high gradients and the transport of sediment with a relatively high sand/mud ratio. The turbidite facies association scheme, which was developed exclusively from ancient active-margin fans, should be applied to mature passive-margin fans with qualifications because of the differences in spatial distribution of turbidite facies and their associations.

  3. Fanning the Optimal Breeze with an Abanico

    Science.gov (United States)

    Goon, Grace; Marthelot, Joel; Reis, Pedro; MIT EGS Lab Team

    Flexible hand-held fans, or abanicos, are universally employed as cooling devices that are both portable and sustainable. Their to and fro axial motion about one's hand generates an airflow that increases the evaporation rate near the skin and refreshes. We study this problem in the context of fluid-structure interaction, through precision model experiments. We first characterize the elastic properties of a semi-circular thin plates with various thickness and evaluate their aerodynamic performance in a custom built apparatus. The air velocity profile that results from the flapping motion of the fan is characterized for different driving conditions. A systematic variation of the geometric and elastic parameters, along with an exploration of the parameter space of the periodic driving motion (amplitude and frequency), allows us to establish optimal design and operational conditions for maximal output of the generated airflow, while minimizing the input power.

  4. Gigapixel Images Connect Sports Teams with Fans

    Science.gov (United States)

    2013-01-01

    Technology developed at Ames Research Center to take high-resolution imagery on Mars is now being used in baseball stadiums across the country. New York City-based Major League Baseball Advanced Media LP customized the platform to accommodate in-game shots that capture nearly the whole stadium. Fans navigate the photos online and tag themselves and their friends using social media tools.

  5. 超声波萃取-原子吸收光谱法测定不同植物油中多种矿物质元素%Determination of mineral elements in vegetable oils by atomic absorption with ultrasonication

    Institute of Scientific and Technical Information of China (English)

    姜波; 胡文忠; 刘长建; 马堃; 王薇

    2013-01-01

    研究采用索氏提取法提取了大豆、葵花籽、花生、油菜籽、芝麻、棉籽,以及蓖麻和油桐种的油脂.油样用硝酸和过氧化氢经超声波处理,经过过滤,得到了清澈透明的样品溶液.采用原子吸收光谱法(回收率97.5%~103.8%)测定了所提油中镁、钾、钠、钙、铁、铜、锌、锶和锰含量,在6种食用植物油中白花生油Na/K比值最小,其次为葵花籽油;Ca/Mg和Cu/Zn比值,葵花籽油高于白花生油.从金属元素角度来考虑,对于预防和治疗高血压有益的首选植物油应为葵花籽油.对人体有害的蓖麻油和桐油金属元素含量与食用植物油相当,若食用植物油中添加了蓖麻油和桐油,仅依靠金属元素含量检测是难以鉴别的,应结合油中有机成分的分析加以区分.%Oils were extracted from soybean,sunflower seed,peanut,rapeseed,sesame,castor bean and tung tree seed with Soxhlet extraction method.The oil samples were treated with ultrasonic extraction by adding nitric acid and hydrogen peroxide,the clear transparent sample solutions were obtained after filtrated.The contents of magnesium,potassium,sodium,calcium,iron,copper,zinc,strontium and manganese were determined by atomic absorption spectrometry(recovery ratios of the elements was 97.3% to 103.8%).Na/K specific value of white peanut oil was the smallest;secondly one was of sunflower seed oil among the six kinds of edible vegetable oils,and Ca/Mg and Cu/Zn specific values of sunflower seed oil were higher than white peanut oil.Therefore sunflower seed oil should be chosen prior for preventing and treating hypertension considering the metallic element content.The metallic element contents of castor oil and tung oil being harmful to human were matched with the six edible vegetable oils,so it was not able to distinguish the oil which was added the them into the edible vegetable oils,and should combine the analysis of organic components.

  6. Fan edits and the legacy of The Phantom Edit

    Directory of Open Access Journals (Sweden)

    Joshua Wille

    2014-09-01

    Full Text Available A fan edit can generally be defined as an alternative version of a film or television text created by a fan. It offers a different viewing experience, much as a song remix offers a different listening experience. The contemporary wave of fan edits has emerged during the remix zeitgeist of digital media and at a time when digital video editing technology has become more affordable and popular. The increasing number of alternative versions of films and the works of revisionist Hollywood filmmakers such as George Lucas have contributed to a greater public understanding of cinema as a fluid medium instead of one that exists in a fixed form. The Phantom Edit (2000, a seminal fan edit based on Lucas's Star Wars Episode I: The Phantom Menace (1999, inspired new ranks of fan editors. However, critics have misunderstood fan edits as merely the work of disgruntled fans. In order to provide a critical and historical basis for studies in fan editing as a creative practice, I examine previous interpretations of fan edits in the context of relevant contemporary works, and I use an annotated chronology of The Phantom Edit to trace its influence on subsequent fan editing communities and uncover their relationship with intellectual property disputes.

  7. "Emotions-Only" versus "Special People": Genre in fan discourse

    Directory of Open Access Journals (Sweden)

    Louisa Ellen Stein

    2008-09-01

    Full Text Available This essay looks at genre as a complex set of discursive threads running unevenly through production, TV text, and fan reception. Through a case study of the reception of fan favorite Roswell, this essay interrogates the role of genre in spectatorship. In its mixing of teen and science fiction elements, Roswell trod upon contested generic spaces, eliciting strong reaction from its viewers. Connections between genre and gender came to the fore, as producer commentary linked science fiction with male audiences and teen romance with female audiences. Fans responded with analyses that greatly complicated and at times overtly rejected industrial suppositions regarding the gendered work of genre. Through these fan conversations, we can witness the complexity of genre as discursive thread moving through not only TV texts but also multivariant fan responses. I intend this essay to work at two levels. My analysis of fan responses to Roswell models the possibilities of a close study of genre discourse. At the same time, my case study probes the nature of genre in fan engagement, as genre discourses intersect with other fan concerns such as character identification, perceptions of textual quality, and questions of gender representation. While we cannot necessarily look to fan accounts for proof of how viewers engage with genre, they do tell us how fans frame their engagement with genre, how they incorporate genre into their performance of fannishness, and how they perform and thus enact genre itself as a shared cultural process.

  8. The aerodynamics of a wind-tunnel fan

    Science.gov (United States)

    Corson, Blake W

    1941-01-01

    The vortex blade-element theory modified to apply to an axial fan working in a duct is reviewed. Thrust and power coefficients for a fan are identified with the corresponding coefficients for airplane propellers. The relation of pressure produced by the fan to the blade-element coefficients is developed. The distribution of axial velocity of fluid through a fan is assumed to be controlled by the fan itself. The radial distribution of tangential velocity imported by the fan to fluid moving through the fan is shown to be independent of the axial-velocity distribution. A nondimensional coefficient, designated the rotation constant, is introduced. This constant is based solely upon design information. The use of the rotation constant in simplifying the design of a fan for a specific operating condition is demonstrated. Based on the use of the rotation constant, a graphical method is outlined by which the performance of a given fan in a given wind tunnel may be predicted and by which the distributions of axial velocity of the fluid through the fan under various operating conditions may be established.

  9. A Fan-tastic Alternative to Bulbs: Learning Circuits with Fans

    Science.gov (United States)

    Ekey, Robert; Edwards, Andrea; McCullough, Roy; Reitz, William; Mitchell, Brandon

    2017-01-01

    The incandescent bulb has been a useful tool for teaching basic electrical circuits, as brightness is related to the current or power flowing through a bulb. This has led to the development of qualitative pedagogical treatments for examining resistive combinations in simple circuits using bulbs and batteries, which were first introduced by James Evans and thoroughly expanded upon by McDermott and others. This paper argues that replacing bulbs with small computer fans leads to similar, if not greater, insight of experimental results that can be qualitatively observed using a variety of senses. The magnitude of current through a fan is related to the frequency of the rotating fan blades, which can be seen, heard, and felt by the students. Experiments using incandescent bulbs only utilize vision, which is not ideal as the human eyes' perception of brightness is skewed because the response to light intensity is logarithmic rather than linear.

  10. Numerical Investigation on the Separated Flow of Axial Flow Stator in Diagonal Flow Fan

    Science.gov (United States)

    Kinoue, Yoichi; Shiomi, Norimasa; Setoguchi, Toshiaki; Kaneko, Kenji; Jin, Yingzi

    2010-06-01

    Experimental and numerical investigations were conducted for the internal flow of the stator of the diagonal flow fan. Corner separation near the hub surface and the suction surface of the stator blade are focused on. At low flow rate of 80% of the design flow rate, the corner separation between the suction surface and the hub surface can be found in both experimental and numerical results. Separation vortices are found in the computed oil flow on both suction and hub surfaces at 80% of the design flow rate in the three-dimensional numerical simulation.

  11. Beam fanning effect and image storage in Ce: KNSBN crystal

    Institute of Scientific and Technical Information of China (English)

    LI PanLai; GUO QingLin; WANG ZhiJun; PANG LiBin; LIANG BaoLai

    2007-01-01

    A non-synchronously-numerating experimental system is applied in this research. The effect of the incident beam intensity Ⅰ and the beam incident angle θ on beam fanning effect is investigated with a singular beam incident on Ce:KNSBN crystal. The results show that the beam fanning effect strongly depends on Iand θ. The threshold effect of/for the beam fanning in Ce:KNSBN crystal is observed, and the threshold intensity of incident beam keeps the same value of 38.2 mW/cm2 for different θ, and the steady beam fanning intensity Ifsat reaches a peak at θ=15° under the same Ⅰ. In addition, the effect of the incident beam modulated on the beam fanning noise and holographic storage in Ce:KNSBN crystal is studied. And the results suggest that the beam fanning noise is effectively suppressed, and the quality of the reappearance image is greatly improved.

  12. Procedure for Balancing an Air Distribution System with Decentralised Fans

    DEFF Research Database (Denmark)

    Gunner, Amalie; Hultmark, Göran; Vorre, Anders

    2015-01-01

    of the fans. In conventional air distribution systems the fan provides the necessary pressure to overcome the resistance in the branch with the highest pressure resistance. This gives an unnecessary overpressure in the remaining branches that does not provide any useful purpose. In order to decrease the fan......This paper presents results from an on-going project concerning new design procedures for mechanical ventilation systems with low energy use. Conventional constant air volume (CAV) systems are usually balanced using flat plate dampers. The purpose of using balancing dampers is to intentionally...... pressure requirements the fan was dimensioned for the branch with the least pressure resistance. The decentralised fans then provided sufficient pressure to overcome the exact resistance in the corresponding branch. The results show that by using decentralised fans in duct systems instead of dampers...

  13. Procedure for Balancing an Air Distribution System with Decentralised Fans

    DEFF Research Database (Denmark)

    Gunner, Amalie; Hultmark, Göran; Vorre, Anders;

    2015-01-01

    This paper presents results from an on-going project concerning new design procedures for mechanical ventilation systems with low energy use. Conventional constant air volume (CAV) systems are usually balanced using flat plate dampers. The purpose of using balancing dampers is to intentionally...... flawed. This paper presents a new procedure for balancing of CAV systems in combination with decentralised fans. The new system was based on replacing the balancing dampers with decentralised fans. By replacing the balancing dampers with decentralised fans, airflows can be balanced by adjusting the speed...... of the fans. In conventional air distribution systems the fan provides the necessary pressure to overcome the resistance in the branch with the highest pressure resistance. This gives an unnecessary overpressure in the remaining branches that does not provide any useful purpose. In order to decrease the fan...

  14. High pressure axial flow fans for modern coal power stations

    Energy Technology Data Exchange (ETDEWEB)

    Cyrus, Vaclav [AHT Energetika s.r.o., Praha (Czech Republic); Koci, Petr [ZVVZ Milevsko a.s. (Czech Republic)

    2008-07-01

    Brown coal fired power stations, located in Northern Bohemia, have mostly older boiler blocks with an output of 110 and 200 MWe. Flue gases are cleaned by the desulphurization plants installed between 1993 and 1997. Usually, each boiler block has two air fans and one to three flue gas fans. Flue gas fans operate in severe conditions; fan blades should be resistant to the flue gases containing sulphur and acid drops with the operating temperature at 170 C to 190 C. Additionally, flue gas also often contains ash particles. Currently, some boiler blocks are gradually being refurbished. New blocks with an electrical power output of 600 to 700 MWe are at the design stage. Submitted paper shows our design study of one stage axial flow fan for the new blocks. Results from the new aerodynamic research of the axial flow stages were used in the fan design. (orig.)

  15. Determination of the mineral compositions of some selected oil-bearing seeds and kernels using Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES

    Directory of Open Access Journals (Sweden)

    Musa Özcan, M.

    2006-06-01

    Full Text Available The aim of this paper was to establish the mineral contents of oil-bearing seeds and kernels such as peanut, turpentine, walnut, hazelnut, sesame, corn, poppy, almond, sunflower etc., using Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES. Significant differences in mineral composition were observed among crops. All seeds and kernels contained high amounts of Al, Ca, Fe, K, Mg, Na, P and Zn. B, Cr, Cu, Li, Ni, Sr, Ti while V contents of the crops were found to be very low. The levels of K and P of all crops in this study were found to be higher than those of other seeds and kernels. The results obtained from analyses of the crops showed that the mean levels of potassiumcontent ranged from 1701.08 mg/kg (corn to 20895.8 mg/kg (soybean, the average content of phosphorus ranged from 3076.9 mg/kg (turpentine to 12006,5 mg/kg to 2617.4 mg/kg (cotton seed, and Ca from 68.4 mg/kg (corn to 13195.7 mg/kg (poppy seed. The results show that these values may  be useful for the evaluation of dietary information. Particularly the obtained results provide evidence that soybean, pinestone and poppy seed are a good source of K, P and Ca, respectively. Whereas pinestone is a good source of zinc.La finalidad del trabajo es establecer el contenido en elementos minerales de semillas oleaginosas tales como cacahuetes, trementina, avellana, sesamo, maiz, almendras, girasol, utilizando ICP-AES. Se han observado diferencias significativas en la composición de minerales entre cosechas. Todas las semillas contienen cantidades elevadas de Al, Ca, Fe, K, Mg, Na, P y Zn. Los contenidos de B, Cr, Cu, Li, Ni, Sr, Ti y V, sin embargo, fueron bajos. Los contenidos de K y P en todas las semillas estudiadas fueron superiores a las de otras semillas. El contenido medio de K osciló entre 1.701,1 mg/kg (maiz a 20.895,8 mg/kg (soja, el P entre 3.076.9 mg/kg (trementina a 12.006.5 mg/kg o 2.617,4 mg/kg (semilla de algodón, y Ca de 68,4 mg/kg (maiz a 13.195,7 mg

  16. Energy consumption characteristics of transports using the prop-fan concept

    Science.gov (United States)

    1976-01-01

    The fuel saving and economic potentials of the prop-fan high-speed propeller concept were evaluated for twin-engine commercial transport airplanes designed for 3333.6 km range, 180 passengers, and Mach 0.8 cruise. A fuel saving of 9.7% at the design range was estimated for a prop-fan airplane having wing-mounted engines, while a 5.8% saving was estimated for a design having the engines mounted on the aft body. The fuel savings and cost were found to be sensitive to the propeller noise level and to aerodynamic drag effects due to wing-slipstream interaction. Uncertainties in these effects could change the fuel savings as much as + or - 50%. A modest improvement in direct operating cost (DOC) was estimated for the wing-mounted prop-fan at current fuel prices. This improvement could become substantial in the event of further relative increases in the price of oil. The improvement in DOC requires the achievement of the nominal fuel saving and reductions in propeller and gearbox maintenance costs relative to current experience.

  17. On limited fan-in optimal neural networks

    Energy Technology Data Exchange (ETDEWEB)

    Beiu, V.; Makaruk, H.E. [Los Alamos National Lab., NM (United States); Draghici, S. [Wayne State Univ., Detroit, MI (United States). Vision and Neural Networks Lab.

    1998-03-01

    Because VLSI implementations do not cope well with highly interconnected nets the area of a chip growing as the cube of the fan-in--this paper analyses the influence of limited fan in on the size and VLSI optimality of such nets. Two different approaches will show that VLSI- and size-optimal discrete neural networks can be obtained for small (i.e. lower than linear) fan-in values. They have applications to hardware implementations of neural networks. The first approach is based on implementing a certain sub class of Boolean functions, IF{sub n,m} functions. The authors will show that this class of functions can be implemented in VLSI optimal (i.e., minimizing AT{sup 2}) neural networks of small constant fan ins. The second approach is based on implementing Boolean functions for which the classical Shannon`s decomposition can be used. Such a solution has already been used to prove bounds on neural networks with fan-ins limited to 2. They generalize the result presented there to arbitrary fan-in, and prove that the size is minimized by small fan in values, while relative minimum size solutions can be obtained for fan-ins strictly lower than linear. Finally, a size-optimal neural network having small constant fan-ins will be suggested for IF{sub n,m} functions.

  18. The Mechanical Impact of Aerodynamic Stall on Tunnel Ventilation Fans

    Directory of Open Access Journals (Sweden)

    A. G. Sheard

    2012-01-01

    Full Text Available This paper describes work aimed at establishing the ability of a tunnel ventilation fan to operate without risk of mechanical failure in the event of aerodynamic stall. The research establishes the aerodynamic characteristics of a typical tunnel ventilation fan when operated in both stable and stalled aerodynamic conditions, with and without an anti-stall stabilisation ring, with and without a “nonstalling” blade angle and at full, half, and one quarter design speed. It also measures the fan’s peak stress, thus facilitating an analysis of the implications of the experimental results for mechanical design methodology. The paper concludes by presenting three different strategies for tunnel ventilation fan selection in applications where the selected fan will most likely stall. The first strategy selects a fan with a low-blade angle that is nonstalling. The second strategy selects a fan with a high-pressure developing capability. The third strategy selects a fan with a fitted stabilisation ring. Tunnel ventilation system designers each have their favoured fan selection strategy. However, all three strategies can produce system designs within which a tunnel ventilation fan performs reliably in-service. The paper considers the advantages and disadvantages of each selection strategy and considered the strengths and weaknesses of each.

  19. K-pop Reception and Participatory Fan Culture in Austria

    Directory of Open Access Journals (Sweden)

    Sang-Yeon Sung

    2013-12-01

    Full Text Available K-pop’s popularity and its participatory fan culture have expanded beyond Asia and become significant in Europe in the past few years. After South Korean pop singer Psy’s “Gangnam Style” music video topped the Austrian chart in October 2012, the number and size of K-pop events in Austria sharply increased, with fans organizing various participatory events, including K-pop auditions, dance festivals, club meetings, quiz competitions, dance workshops, and smaller fan-culture gatherings. In the private sector, longtime fans have transitioned from participants to providers, and in the public sector, from observers to sponsors. Through in-depth interviews with event organizers, sponsors, and fans, this article offers an ethnographic study of the reception of K-pop in Europe that takes into consideration local interactions between fans and Korean sponsors, perspectives on the genre, patterns of social integration, and histories. As a case study, this research stresses the local situatedness of K-pop fan culture by arguing that local private and public sponsors and fans make the reception of K-pop different in each locality. By exploring local scenes of K-pop reception and fan culture, the article demonstrates the rapidly growing consumption of K-pop among Europeans and stresses multidirectional understandings of globalization.

  20. A measuring stand for a ducted fan aircraft propulsion unit

    Directory of Open Access Journals (Sweden)

    Hlaváček David

    2014-03-01

    Full Text Available The UL-39 ultra-light aircraft which is being developed by the Department of Aerospace Engineering, Faculty of Mechanical Engineering, Czech Technical University in Prague, is equipped with an unconventional ducted fan propulsion unit. The unit consists of an axial fan driven by a piston engine and placed inside a duct ended with a nozzle. This article describes the arrangement of a modernised measuring stand for this highly specific propulsion unit which will be able to measure the fan pressure ratio and velocity field in front of and behind the fan and its characteristic curve.

  1. Improved extraction method for the determination of iron, copper, and nickel in new varieties of sunflower oil by atomic absorption spectroscopy.

    Science.gov (United States)

    Ansari, Rehana; Kazi, Tasneem G; Jamali, Mohammad K; Arain, Mohammad B; Sherazi, Syed T; Jalbani, Nusrat; Afridi, Hassan I

    2008-01-01

    A simple and fast procedure is proposed for the extraction of iron (Fe), copper (Cu), and nickel (Ni) in 16 varieties of sunflower seed oil samples using an ultrasonic bath. The experimental parameters of the ultrasonic-assisted extraction (UAE) method were optimized to improve the sensitivity and detect the metals at trace levels in minimum time. Conventional wet acid digestion method was used for comparative purposes. The optimum recovery of all 3 metals was obtained by UAE for 7 min, while the separation of aqueous and organic phases after extraction using centrifugation (UAE-2) required 3 min, as compared to the conventional equilibration method (UAE-1) that required 90 min. The respective recoveries of Cu, Fe, and Ni obtained with UAE-2 were in the range of 95.8-97.5, 93.5-98.3, and 95.6-98.2%, respectively, for different varieties of sunflower oil samples. Accuracy was determined by the standard addition method. Under the optimum operating conditions, the limits of detection obtained from the standard addition curves were 21.7, 20.4, and 35.6 ng/mL for Fe, Cu, and Ni, respectively. The fact that all varieties of sunflower oil contain significant amounts of Fe, Cu, and Ni indicates the deterioration of sunflower oil quality immediately after extraction from seeds, which poses a threat to oil quality and human health.

  2. Extreme Loading of Aircraft Fan Blade

    CERN Document Server

    Datta, Dibakar

    2013-01-01

    The response of an aircraft fan blade manufactured by composites under the action of static and impact load has been studied in this report. The modeling and analysis of the geometry has been done using CASTEM 2007 version. For the quasi static analysis, the pressure has been incrementally applied until it satisfies the failure criteria. The deformed configuration, strain, Von-Mises stress, and the deflection of the blade have been studied. The response of the system e.g. deformation time history due to the impact of the projectile has been studied where the Newmark method for the dynamic problem has been implemented.

  3. Condensate Accretion in Shock Tube's Expansion Fan

    Science.gov (United States)

    Mezonlin, Ephrem-Denis; DeSilva, Upul P.; Hunte, F.; Johnson, Joseph A., III

    1997-01-01

    It has been shown that turbulence and temperature influence the droplet sizes in expansion fan induced condensation by studying the Rayleigh scattering from one port in our shock tube's test section. We have modified our set-up so as to allow, using two ports, the real time measurement of the influence of turbulence and temperature on the rate at which these droplets grow. To do this, we looked at the Rayleigh scattering from two different ports for ten Reynolds numbers at five different temperatures. We modeled the time of flight of droplets, using the equations of one-dimensional gas dynamics and the measured shock wave speed in shock tube's driven section.

  4. Through flow analysis of pumps and fans

    Science.gov (United States)

    Neal, A. N.

    1980-08-01

    Incompressible through flow calculations in axial, mixed and centrifugal flow pumps and fans are described. An iterative scheme is used. A simple blade to blade model is applied on the surfaces of revolution defined by the meridional streamlines. This defines the fluid properties and the mean stream surface (S2 surface) for the next meridional solution. A computer program is available allowing the method to be applied for design purposes. APL is used for input and output and FORTRAN IV for computation. A typical calculation requires 30 sec of Univac 1100 time.

  5. Application of the extraction induced by emulsion breaking for the determination of Cu, Fe and Mn in used lubricating oils by flame atomic absorption spectrometry.

    Science.gov (United States)

    Caldas, Luiz Fernando S; Brum, Daniel M; de Paula, Carlos Eduardo R; Cassella, Ricardo J

    2013-06-15

    A novel approach is proposed for the sample preparation of used lubricating oils to determine Cu, Fe and Mn by FAAS. The method is based on the extraction induced by emulsion breaking, in which the elements of interest are transferred to an aqueous phase before the measurement by FAAS. In the method, each sample of used lubricating oil was diluted with toluene (20% v/v) and the resulting solution was emulsified with a Triton X-114 solution containing HNO3. Further, the water-in-oil emulsion was broken by centrifugation for 30 min at 3500 rpm, originating a system with two well-separated phases: (i) the upper phase, containing the used lubricating oil diluted in toluene and (ii) the lower aqueous phase, containing the analytes that were extracted from oil. The lower phase was collected, diluted with water and the analytes were determined by FAAS. The optimization of the methodology was performed by studying the influence of different parameters that could affect the extraction efficiency such as the nature and concentration of the solvent used for sample dilution, the concentrations of HNO3 and Triton X-114 in the solution employed for emulsification and the operational conditions for extraction (extraction, centrifugation and sampling times). The limits of quantification for Cu, Fe and Mn were 2.9, 77 and 8.2 ng g(-1), respectively. The accuracy of the method was evaluated by comparison with the reference method based on the total digestion of the samples in a closed-vessel microwave oven. There were no statistical differences between the results obtained with the proposed method and the reference one, except for Fe in the cases where its concentration was higher than 80 µg g(-1).

  6. Case study of French and Spanish fan reception of Game of Thrones

    Directory of Open Access Journals (Sweden)

    Mélanie Bourdaa

    2015-06-01

    Full Text Available The reception of the American TV show Game of Thrones (2011– by French and Spanish fans and nonfans is addressed via a qualitative methodology, the goal of which is to understand how European viewers perceive themselves as fans and what it means for them to be fans. Analysis of characteristics of a specifically European reception helps us learn what fan studies tell us about fans and what fans really think about fandoms.

  7. The Retarding Force on a Fan-Cart Reversing Direction

    Science.gov (United States)

    Aurora, Tarlok S.; Brunner, Bernard J.

    2011-01-01

    In introductory physics, students learn that an object tossed upward has a constant downward acceleration while going up, at the highest point and while falling down. To demonstrate this concept, a self-propelled fan cart system is used on a frictionless track. A quick push is given to the fan cart and it is allowed to move away on a track under…

  8. Female fans of men's football - a case study in Denmark

    DEFF Research Database (Denmark)

    Pfister, Gertrud Ursula; Lenneis, Verena; Mintert, Svenja-Maria

    2013-01-01

    to a 'man's world' and what are their roles in this 'male environment'? The statements of interviewees revealed that female fans have to cope with a measure of sexism, but that they can adopt the men's perspectives in order to be accepted as 'authentic fans'. Other women reacted on men's domination...

  9. Using Fan Fiction to Teach Critical Reading and Writing Skills

    Science.gov (United States)

    Kell, Tracey

    2009-01-01

    In this article, the author talks about fan fiction, which is defined by Jenkins (2008) as "original stories and novels which are set in the fictional universe of favorite television series, films, comics, games or other media properties." Fan fiction generally involves writing stories with a combination of established characters and established…

  10. Acoustic Measurements of an Uninstalled Spacecraft Cabin Ventilation Fan Prototype

    Science.gov (United States)

    Koch, L. Danielle; Brown, Clifford A.; Shook, Tony D.; Winkel, James; Kolacz, John S.; Podboy, Devin M.; Loew, Raymond A.; Mirecki, Julius H.

    2012-01-01

    Sound pressure measurements were recorded for a prototype of a spacecraft cabin ventilation fan in a test in the NASA Glenn Acoustical Testing Laboratory. The axial fan is approximately 0.089 m (3.50 in.) in diameter and 0.223 m (9.00 in.) long and has nine rotor blades and eleven stator vanes. At design point of 12,000 rpm, the fan was predicted to produce a flow rate of 0.709 cu m/s (150 cfm) and a total pressure rise of 925 Pa (3.72 in. of water) at 12,000 rpm. While the fan was designed to be part of a ducted atmospheric revitalization system, no attempt was made to throttle the flow or simulate the installed configuration during this test. The fan was operated at six speeds from 6,000 to 13,500 rpm. A 13-microphone traversing array was used to collect sound pressure measurements along two horizontal planes parallel to the flow direction, two vertical planes upstream of the fan inlet and two vertical planes downstream of the fan exhaust. Measurements indicate that sound at blade passing frequency harmonics contribute significantly to the overall audible noise produced by the fan at free delivery conditions.

  11. Procedure for Balancing an Air Distribution System with Decentralised Fans

    DEFF Research Database (Denmark)

    Gunner, Amalie; Hultmark, Göran; Vorre, Anders

    2015-01-01

    there is a potential for energy saving. In this study the calculated saving in the power consumption for the main fan was found to be 40%. The results also show that when dampers are replaced with decentralised fans with the same efficiency the overall power saving potential was 16%. In the study a mock-up...

  12. Amateur mythographies: Fan fiction and the myth of myth

    Directory of Open Access Journals (Sweden)

    Ika Willis

    2016-03-01

    Full Text Available This paper draws on classical scholarship on myth in order to critically examine three ways in which scholars and fans have articulated a relationship between fan fiction and myth. These are (1 the notion of fan fiction as a form of folk culture, reclaiming popular story from corporate ownership; (2 the notion of myth as counterhegemonic, often feminist, discourse; (3 the notion of myth as a commons of story and a universal story world. I argue that the first notion depends on an implicit primitivizing of fan fiction and myth, which draws ultimately on the work of Gottfried von Herder in the 18th century and limits our ability to produce historically and politically nuanced understandings of fan fiction. The second notion, which is visible in the work of Henry Jenkins and Constance Penley, is more helpful because of its attention to the politics of narration. However, it is the third model of myth, as a universal story world, where we find the richest crossover between fan fiction's creative power and contemporary classical scholarship on myth, especially in relation to Sarah Iles Johnston's analysis of hyperserial narrative. I demonstrate this through some close readings of fan fiction from the Greek and Roman Mythology fandom on Archive of Our Own. I conclude the paper by extending Johnston's arguments to show that fan-fictional hyperseriality, specifically, can be seen as mythic because it intervenes not only in the narrative worlds of its source materials but also in the social world of its telling.

  13. Gender constructions and negotiations of female football fans

    DEFF Research Database (Denmark)

    Lenneis, Verena; Pfister, Gertrud Ursula

    2015-01-01

    aims to give insight into gender constructions and negotiations of female football fans in the stands. Drawing on a social constructivist perspective to gender and Bourdieu's (1984) approaches to field, capital and habitus, we explored the experiences and opinions of female fans. The methods employed...

  14. 76 FR 50739 - Hung Ta Fan: Debarment Order

    Science.gov (United States)

    2011-08-16

    ... bases this order on a finding that Mr. Fan was convicted of a felony under Federal law for conduct... law). FDA's finding that debarment is appropriate is based on the felony conviction referenced herein... Thailand, when in fact he knew that the honey originated in China. Mr. Fan's actions allowed him to avoid...

  15. Simpler Variable-Speed Drive for Fan or Pump

    Science.gov (United States)

    Obler, H. D.

    1982-01-01

    Static pressure developed by a fan or pump is used directly to control its speed in a new drive unit. System is simpler and more economical than many other speed controllers, although it is less accurate and has a narrower speed range. However, since very accurate control is not usually required for fans and pumps, unit would work well in many applications.

  16. Facilitating Attuned Interactions: Using the FAN Approach to Family Engagement

    Science.gov (United States)

    Gilkerson, Linda

    2015-01-01

    Erikson Institute's Fussy Baby Network® (FBN) is a national model prevention program known for its approach to family engagement called the FAN (Gilkerson & Gray, 2014; Gilkerson et al., 2012). The FAN is both a conceptual framework and a practical tool to facilitate attunement in helping relationships and promote reflective practice. This…

  17. Wikipedia and participatory culture: Why fans edit [symposium

    Directory of Open Access Journals (Sweden)

    Paul Thomas

    2016-09-01

    Full Text Available Online, fans of popular culture media partake in participatory culture in various ways, such as writing fan fiction and scrutinizing media on message boards. Another way they do so is by editing relevant articles in the online encyclopedia Wikipedia. In fact, research has shown that Wikipedia articles skew heavily toward pop culture, suggesting that fans of pop culture are among the most enthusiastic of Wikipedia's editors. Of course, the question emerges: Why are pop culture fans in particular so interested in editing Wikipedia? Building on previous research, I argue that fans want to take part in the production of the media that they enjoy, that Wikipedia allows editors to create their own paratext (i.e., the Wikipedia article in relation to a main text (e.g., a movie, a television show, a book series, and that this paratext may be heavily used by the general public. Such usage is a form of implicit approval that affirms the editors' knowledge and encourages them to make more edits. Thus, Wikipedia validates the fan editor's work in a way that other outlets for participatory culture (e.g., fan fiction, fan art, songwriting cannot.

  18. Energy fan power consumption comparison of subway station HVAC system

    Institute of Scientific and Technical Information of China (English)

    JIANGYong; ZHUYingxin

    2003-01-01

    Subway thermal environment control system is a mass energy consumed system. The fan operation is the Key of energy saving. Some feasible fan operation modes are proposed and compared in this paper from the view of energy and operation cost saving. It is concluded that VAV is the optimal operation mode for metro system with highest energy saving.

  19. Nocturnal Fanning Suppresses Downy Mildew Epidemics in Sweet Basil.

    Directory of Open Access Journals (Sweden)

    Yigal Cohen

    Full Text Available Downy mildew is currently the most serious disease of sweet basil around the world. The oomycete causal agent Peronospora belbahrii requires ≥ 4h free leaf moisture for infection and ≥7.5h of water-saturated atmosphere (relative humidity RH≥95% at night for sporulation. We show here that continued nocturnal fanning (wind speed of 0.4-1.5 m/s from 8pm to 8am dramatically suppressed downy mildew development. In three experiments conducted during 2015, percent infected leaves in regular (non-fanned net-houses reached a mean of 89.9, 94.3 and 96.0% compared to1.2, 1.7 and 0.5% in adjacent fanned net-houses, respectively. Nocturnal fanning reduced the number of hours per night with RH≥95% thus shortened the dew periods below the threshold required for infection or sporulation. In experiments A, B and C, the number of nights with ≥4h of RH≥95% was 28, 10 and 17 in the non-fanned net-houses compared to 5, 0 and 5 in the fanned net-houses, respectively. In the third experiment leaf wetness sensors were installed. Dew formation was strongly suppressed in the fanned net-house as compared to the non-fanned net-house. Healthy potted plants became infected and sporulated a week later if placed one night in the non-fanned house whereas healthy plants placed during that night in the fanned house remained healthy. Infected potted basil plants sporulated heavily after one night of incubation in the non-fanned house whereas almost no sporulation occurred in similar plants incubated that night in the fanned house. The data suggest that nocturnal fanning is highly effective in suppressing downy mildew epidemics in sweet basil. Fanning prevented the within-canopy RH from reaching saturation, reduced dew deposition on the leaves, and hence prevented both infection and sporulation of P. belbahrii.

  20. Variable pitch fan system for NASA/Navy research and technology aircraft

    Science.gov (United States)

    Ryan, W. P.; Black, D. M.; Yates, A. F.

    1977-01-01

    Preliminary design of a shaft driven, variable-pitch lift fan and lift-cruise fan was conducted for a V/STOL Research and Technology Aircraft. The lift fan and lift-cruise fan employed a common rotor of 157.5 cm diameter, 1.18 pressure ratio variable-pitch fan designed to operate at a rotor-tip speed of 284 mps. Fan performance maps were prepared and detailed aerodynamic characteristics were established. Cost/weight/risk trade studies were conducted for the blade and fan case. Structural sizing was conducted for major components and weights determined for both the lift and lift-cruise fans.

  1. Costs and benefits of energy efficiency improvements in ceiling fans

    Energy Technology Data Exchange (ETDEWEB)

    Shah, Nihar; Sathaye, Nakul; Phadke, Amol; Letschert, Virginie [Lawrence Berkeley National Lab., CA (United States). Environmental Energy Technology Division

    2013-10-15

    Ceiling fans contribute significantly to residential electricity consumption, especially in developing countries with warm climates. The paper provides analysis of costs and benefits of several options to improve the efficiency of ceiling fans to assess the global potential for electricity savings and green house gas (GHG) emission reductions. Ceiling fan efficiency can be cost-effectively improved by at least 50% using commercially available technology. If these efficiency improvements are implemented in all ceiling fans sold by 2020, 70 terawatt hours per year could be saved and 25 million metric tons of carbon dioxide equivalent (CO2-e) emissions per year could be avoided, globally. We assess how policies and programs such as standards, labels, and financial incentives can be used to accelerate the adoption of efficient ceiling fans in order to realize potential savings.

  2. Portable Fan Assembly for the International Space Station

    Science.gov (United States)

    Jenkins, Arthur A.; Roman, Monsi C.

    1999-01-01

    NASA/ Marshall Space Flight Center (NASA/MSFC) is responsible for the design and fabrication of a Portable Fan Assembly (PFA) for the International Space Station (ISS). The PFA will be used to enhance ventilation inside the ISS modules as needed for crew comfort and for rack rotation. The PFA consists of the fan on-orbit replaceable unit (ORU) and two noise suppression packages (silencers). The fan ORU will have a mechanical interface with the Seat Track Equipment Anchor Assembly, in addition to the power supply module which includes a DC-DC converter, on/standby switch, speed control, power cable and connector. This paper provides a brief development history, including the criteria used for the fan, and a detailed description of the PFA operational configurations. Space Station requirements as well as fan performance characteristics are also discussed.

  3. Sediment velocities from sonobuoys: Bengal Fan, Sunda Trench, Andaman Basin, and Nicobar Fan

    Energy Technology Data Exchange (ETDEWEB)

    Hamilton, E.L.; Bachman, R.T.; Curray, J.R.; Moore, D.G.

    1977-07-10

    New measurements of interval compressional wave velocities were made in the first sediment layer using the sonobuoy technique during two expeditions in the Bay of Bengal, in the Andaman Sea, and over the Nicobar Fan and Sunda Trench. Sediment interval velocities from these areas were added to those previously reported, and revised diagrams and regression equations of instantaneous and mean velocity versus one-way travel time are furnished for four areas of the Bengal Fan, and for the Anadman Basin, Nicobar Fan, Sunda Trench. The velocity gradients directly below the sea floor were used to separate the Bengal Fan into four geoacoustic provinces. In the north and west the velocity gradients are 0.86 and 1.28 s/sup -1/, respectively, whereas in the central part of the fan the gradient is 1.87 s/sup -1/. These variations indicate lesser increases of velocity with depth in the sea floor in the north and west, and they are probably due to more rapid deposition, less consolidation, and less lithification near the riverine source areas of the sediments. The near-surface velocity gradients in the other areas are the Andaman Basin, 1.53 s/sup -1/, the Nicobar Fan 1.63 s/sup -1/, and the Sunda Trench, 1.41 s/sup -1/. The linear velocity gradients (from the sediment surface to a given travel time) in 17 areas of the Indian Ocean, Pacific area, Atlantic Ocean, and Gulf of Mexico were averaged at each 0.1 s from 0 to 0.5 s of one-way travel time. These averaged gradients ranged from 1.32 s/sup -1/ at t=0 to 0.76 s/sup -1/ at t=0.5 s. The regression equation for the velocity gradients a, in s/sup -1/, as a function of one-way travel time t, in seconds, is a=1.316-1.117t (for use from t=0 to 0.5 s). These average velocity gradients can be used with sediment surface velocities and one-way travel times (measured from reflection records) to compute sediment layer thickness in areas of turbidites lacking interval velocity measurements in the first sediment layer.

  4. Development of a Fan for Future Space Suit Applications

    Science.gov (United States)

    Paul. Heather L.; Converse, David; Dionne, Steven; Moser, Jeff

    2010-01-01

    NASA's next generation space suit system will place new demands on the fan used to circulate breathing gas through the ventilation loop of the portable life support system. Long duration missions with frequent extravehicular activities (EVAs), the requirement for significant increases in reliability and durability, and a mission profile that imposes strict limits on weight, volume and power create the basis for a set of requirements that demand more performance than is available from existing fan designs. This paper describes the development of a new fan to meet these needs. A centrifugal fan was designed with a normal operating speed of approximately 39,400 rpm to meet the ventilation flow requirements while also meeting the aggressive minimal packaging, weight and power requirements. The prototype fan also operates at 56,000 rpm to satisfy a second operating condition associated with a single fan providing ventilation flow to two spacesuits connected in series. This fan incorporates a novel nonmetallic "can" to keep the oxygen flow separate from the motor electronics, thus eliminating ignition potential. The nonmetallic can enables a small package size and low power consumption. To keep cost and schedule within project bounds a commercial motor controller was used. The fan design has been detailed and implemented using materials and approaches selected to address anticipated mission needs. Test data is presented to show how this fan performs relative to anticipated ventilation requirements for the EVA portable life support system. Additionally, data is presented to show tolerance to anticipated environmental factors such as acoustics, shock, and vibration. Recommendations for forward work to progress the technology readiness level and prepare the fan for the next EVA space suit system are also discussed.

  5. Alluvial Fan Morphology, distribution and formation on Titan

    Science.gov (United States)

    Birch, S. P. D.; Hayes, A. G.; Howard, A. D.; Moore, J. M.; Radebaugh, J.

    2016-05-01

    Titan is a hydrologically active world, with dozens of alluvial fans that are evidence of sediment transport from high to low elevations. However, the distribution and requirements for the formation of fans on Titan are not well understood. We performed the first global survey of alluvial fans on Titan using Cassini Synthetic Aperture Radar (SAR) data, which cover 61% of Titan's surface. We identified 82 fans with areas ranging from 28 km2 to 27,000 km2. A significant fraction (∼60%) of the fans are restricted to latitudes of ±50-80°, suggesting that fluvial sediment transport may have been concentrated in the near-polar terrains in the geologically recent past. The density of fans is also found to be correlated with the latitudes predicted to have the highest precipitation rates by Titan Global Circulation Models. In equatorial regions, observable fans are not generally found in proximity to dune fields. Such observations suggest that sediment transport in these areas is dominated by aeolian transport mechanisms, though with some degree of recent equatorial fluvial activity. The fan area-drainage area relationship on Titan is more similar to that on Earth than on Mars, suggesting that the fans on Titan are smaller than what may be expected, and that the transport of bedload sediment is limited. We hypothesize that this has led to the development of a coarse gravel-lag deposit over much of Titan's surface. Such a model explains both the morphology of the fans and their latitudinal concentration, yielding insight into the sediment transport regimes that operate across Titan today.

  6. Life, death and revival of debris-flow fans on Earth and Mars : fan dynamics and climatic inferences

    NARCIS (Netherlands)

    de Haas, T.

    2016-01-01

    Alluvial fans are ubiquitous landforms in high-relief regions on Earth and Mars. They have a semi-conical shape and are located at the transition between highlands and adjacent basins. Alluvial fans can form by a range of processes including debris flows, which are water-laden masses of soil and

  7. Life, death and revival of debris-flow fans on Earth and Mars : fan dynamics and climatic inferences

    NARCIS (Netherlands)

    de Haas, T.

    2016-01-01

    Alluvial fans are ubiquitous landforms in high-relief regions on Earth and Mars. They have a semi-conical shape and are located at the transition between highlands and adjacent basins. Alluvial fans can form by a range of processes including debris flows, which are water-laden masses of soil and roc

  8. Life, death and revival of debris-flow fans on Earth and Mars : fan dynamics and climatic inferences

    NARCIS (Netherlands)

    de Haas, T.

    2016-01-01

    Alluvial fans are ubiquitous landforms in high-relief regions on Earth and Mars. They have a semi-conical shape and are located at the transition between highlands and adjacent basins. Alluvial fans can form by a range of processes including debris flows, which are water-laden masses of soil and roc

  9. 石墨炉原子吸收光谱法测定植物油中砷%Determination of arsenic in vegetable oil by graphite furnace atomic absorption spectrophotometry

    Institute of Scientific and Technical Information of China (English)

    俞涛; 蒋雪凤; 钟小伶

    2012-01-01

    Objective:To develop a method for the determination of arsenic in vegetable oil by graphite furnace a-tomic absorption spectrophotometry. Methods: After samples were digested with microwave, magnesium nitrate was added as matrix modifier and then determined by graphite furnace atomic absorption spectrometry. Results: The method had a linear relationship in the range of 0 μg/L ~ 20 μg/L ( r = 0. 9997) , and the detection limit was 0. 006 mg/kg, RSDs were between 2. 7% ~ 3. 2% ,the rate of recoveries were between 84. 7% ~99. 0% . Conclu-sion ; The method is simple, sensitive, reproducible and can be applicable to the determination of arsenic in vegeta-ble oil.%目的:建立检测植物油中砷含量的石墨炉原子吸收光谱方法.方法:样品经微波消化后,采用硝酸镁作为基体改进剂,石墨炉原子吸收光谱法测定.结果:方法线性范围为0 μg/L~ 20 μg/L,相关系数为0.9997,方法检出限为0.006 mg/kg,RSD为2.7%~3.2%,加标回收率为84.7%~99.0%.结论:本法简便、灵敏度高、重现性好,适用于植物油中砷的测定.

  10. Aerodynamic Modelling and Optimization of Axial Fans

    DEFF Research Database (Denmark)

    Sørensen, Dan Nørtoft

    A numerically efficient mathematical model for the aerodynamics oflow speed axial fans of the arbitrary vortex flow type has been developed.The model is based on a blade-element principle, whereby therotor is divided into a number of annular streamtubes.For each of these streamtubes relations...... for velocity, pressure andradial position are derived from the conservationlaws for mass, tangential momentum and energy.The resulting system of equations is non-linear and, dueto mass conservation and pressure equilibrium far downstream of the rotor,strongly coupled.The equations are solved using the Newton...... distributionsof pitch angle and chord length have been chosen as independent variablesin the optimizations.Besides restricting the geometry of the rotor,constraints have been added to ensure a required pressure rise as well asnon-stalled flow conditions.Optimizations have been performed tomaximize the mean value...

  11. A generalization of Ky Fan's inequality

    Directory of Open Access Journals (Sweden)

    Peng Gao

    2001-01-01

    defined by f(x,y=0 and 0Fan's inequality. We also present some results on the comparison of Pn,sα(y−Pn,rα(y and Pn,sα(x−Pn,rα(x for s≥r, α∈ℝ.

  12. Failure analysis of air fan blades

    Institute of Scientific and Technical Information of China (English)

    WANG Yan-qing; JI Zhe; CUI Yong-li; CUI Chun-zhi; SUN Zhi

    2008-01-01

    The failure of all 12 blades of an air fan was investigated by metallurgical and mechanical experiments and an examina-tion of the fracture surface. The experimental results show that the cast aluminium-silicon alloy without any modification had a number of material defects, such as coarse grains, a loose structure, a large number of shrinkage holes, a long and thin bold-pin shaped silicon-phase, poor material strength and serious brittleness. In addition, installed on the spindle without elastic conjunction,blade No. 10 vibrated and inevitably.spun off due to the large centrifugal force. Therefore, blade No. 10 first cracked at the locking handle, then broke at the root, which caused all the other 11 blades to be broken by the crack of blade No.10.

  13. Soap operas and the history of fan discussion

    Directory of Open Access Journals (Sweden)

    Sam Ford

    2008-09-01

    Full Text Available For decades, fans of U.S. soap operas have formed social networks surrounding their shows, and they did so even before the concept entered the vernacular. Soap fans, who started on a geographically local scale and built their communities through grassroots efforts, have found a variety of venues to connect with one another over the past several decades. This study looks at the pre-Internet development of these social networks to show how that trajectory relates to the current online community of soap opera fans. Although several scholars have studied soap opera fandom, few have taken an historical approach at understanding the trajectory of soap fandom, a view especially necessary in an era where online social networks are at the center of audience studies and where cornerstone U.S. soap operas are struggling to retain relevance and audience. To fill this gap, I argue that understanding fan networks today requires looking back to previous methods of fan networking. Soaps' longevity (the youngest U.S. soap is more than 20 years old and frequency (all U.S. daytime soaps are daily make them crucial texts in demonstrating how the roots of fan social networks in a pre-Internet era helped shape that fandom's transition onto the Internet, and they also illustrate the continued evolution of these networks as fans move online.

  14. Experimental determination of tunnel ventilation axial ducted fan performance

    Directory of Open Access Journals (Sweden)

    Šekularac Milan B.

    2016-01-01

    Full Text Available To investigate traffic tunnel ventilation flows, a scaled model of a traffic tunnel with longitudinal ventilation system based on ducted fans is used. Flows in tunnels are influenced by tunnel geometry, fan characteristics, ventilation operation scenario, vehicle traffic, atmospheric factors, etc. To analyze flow fields of tunnels in detail, knowledge of tunnel jet-fan properties and turbulent flow characteristics at the fan exit are required, and can be used as input data for CFD boundary conditions of tunnel flow computation. For this purpose experimental measurements were done using the hot wire anemometry technique. The obtained results, trough ensemble-averaged and time averaged profiles of all velocity components, turbulence intensity, turbulent kinetic energy, integral flow length scales, available Reynolds stresses, Turbulent kinetic energy production rates and the fan thrust performance, are presented. These data allow us to analyze in more detail the influence of fan flow on energy and pollutant removal efficiencies of the tunnel ventilation and to evaluate accuracy of CFD studies on fan improvements.

  15. Reactive control of subsonic axial fan noise in a duct.

    Science.gov (United States)

    Liu, Y; Choy, Y S; Huang, L; Cheng, L

    2014-10-01

    Suppressing the ducted fan noise at low frequencies without varying the flow capacity is still a technical challenge. This study examines a conceived device consisting of two tensioned membranes backed with cavities housing the axial fan for suppression of the sound radiation from the axial fan directly. The noise suppression is achieved by destructive interference between the sound fields from the axial fan of a dipole nature and sound radiation from the membrane via vibroacoustics coupling. A two-dimensional model with the flow effect is presented which allows the performance of the device to be explored analytically. The air flow influences the symmetrical behavior and excites the odd in vacuo mode response of the membrane due to kinematic coupling. Such an asymmetrical effect can be compromised with off-center alignment of the axial fan. Tension plays an important role to sustain the performance to revoke the deformation of the membrane during the axial fan operation. With the design of four appropriately tensioned membranes covered by a cylindrical cavity, the first and second blade passage frequencies of the axial fan can be reduced by at least 20 dB. The satisfactory agreement between experiment and theory demonstrates that its feasibility is practical.

  16. Understanding Himalayan erosion and the significance of the Nicobar Fan

    Science.gov (United States)

    McNeill, Lisa C.; Dugan, Brandon; Backman, Jan; Pickering, Kevin T.; Pouderoux, Hugo F. A.; Henstock, Timothy J.; Petronotis, Katerina E.; Carter, Andrew; Chemale, Farid; Milliken, Kitty L.; Kutterolf, Steffen; Mukoyoshi, Hideki; Chen, Wenhuang; Kachovich, Sarah; Mitchison, Freya L.; Bourlange, Sylvain; Colson, Tobias A.; Frederik, Marina C. G.; Guèrin, Gilles; Hamahashi, Mari; House, Brian M.; Hüpers, Andre; Jeppson, Tamara N.; Kenigsberg, Abby R.; Kuranaga, Mebae; Nair, Nisha; Owari, Satoko; Shan, Yehua; Song, Insun; Torres, Marta E.; Vannucchi, Paola; Vrolijk, Peter J.; Yang, Tao; Zhao, Xixi; Thomas, Ellen

    2017-10-01

    A holistic view of the Bengal-Nicobar Fan system requires sampling the full sedimentary section of the Nicobar Fan, which was achieved for the first time by International Ocean Discovery Program (IODP) Expedition 362 west of North Sumatra. We identified a distinct rise in sediment accumulation rate (SAR) beginning ∼9.5 Ma and reaching 250-350 m/Myr in the 9.5-2 Ma interval, which equal or far exceed rates on the Bengal Fan at similar latitudes. This marked rise in SAR and a constant Himalayan-derived provenance necessitates a major restructuring of sediment routing in the Bengal-Nicobar submarine fan. This coincides with the inversion of the Eastern Himalayan Shillong Plateau and encroachment of the west-propagating Indo-Burmese wedge, which reduced continental accommodation space and increased sediment supply directly to the fan. Our results challenge a commonly held view that changes in sediment flux seen in the Bengal-Nicobar submarine fan were caused by discrete tectonic or climatic events acting on the Himalayan-Tibetan Plateau. Instead, an interplay of tectonic and climatic processes caused the fan system to develop by punctuated changes rather than gradual progradation.

  17. Characterizing subsurface hydraulic heterogeneity of alluvial fan using riverstage fluctuations

    Science.gov (United States)

    Wang, Yu-Li; Yeh, Tian-Chyi Jim; Wen, Jet-Chau; Huang, Shao-Yang; Zha, Yuanyuan; Tsai, Jui-Pin; Hao, Yonghong; Liang, Yue

    2017-04-01

    The objective of this study is to demonstrate the ability of riverstage tomography to estimate 2-D spatial distribution of hydraulic diffusivity (D) of Zhuoshui River alluvial fan, Taiwan, using groundwater level data from 65 wells and stream stage data from 5 gauging stations. In order to accomplish this objective, wavelet analysis is first conducted to investigate the temporal characteristics of groundwater level, precipitation, and stream stage. The results of the analysis show that variations of groundwater level and stream stage are highly correlated over seasonal and annual periods while that between precipitation is less significant. Subsequently, spatial cross-correlation between seasonal variations of groundwater level and riverstage data is analyzed. It is found that the correlation contour map reflects the pattern of sediment distribution of the fan. This finding is further substantiated by the cross-correlation analysis using both noisy and noise-free groundwater and riverstage data of a synthetic aquifer, where aquifer heterogeneity is known exactly. The ability of riverstage tomography is then tested with these synthetic data sets to estimate D distribution. Finally, the riverstage tomography is applied to the alluvial fan. The results of the application reveal that the apex and southeast of the alluvial fan are regions with relatively high D and the D values gradually decrease toward the shoreline of the fan. In addition, D at northern alluvial fan is slightly larger than that at southern. These findings are consistent with the geologic evolution of this alluvial fan.

  18. Fans of Columbine shooters Eric Harris and Dylan Klebold

    Directory of Open Access Journals (Sweden)

    Andrew Ryan Rico

    2015-09-01

    Full Text Available On April 20, 1999, Eric Harris and Dylan Klebold murdered 12 students and one teacher at Columbine High School in Littleton, Colorado, in what was then the deadliest school shooting in American history. Despite causing a national panic and serving as a flash point for larger narratives on bullying, gun control, and media violence, both boys have gained active online fans. These fandoms dedicated to the Columbine shooters are widely referred to as dark examples of Internet communities, while the fans are also frequently denigrated as unstable and violent outcasts. Such dark online fandoms are yet to permeate mainstream culture or to challenge the preexisting perception of these communities as breeding grounds for the next wave of school shooters. While studies have covered the types of fans and their myriad interests, the field remains focused on more conventional examples of fan communities. In an effort to challenge and expand the object of focus when we study fandom, this qualitative study examines Columbine fans and their activity in order to understand the dominant motives they appear to have for engaging with and around such controversial figures and then concludes by exploring how this community might help us reflect more broadly on our concept of fandom. Redeeming these fans as part of diverse and complex communities of social relevance can demonstrate how even a dark fandom such as that of these Columbine shooters provides valuable cultural insights and benefits the field of fan studies.

  19. Atomic resolution images of solid-liquid interfaces

    OpenAIRE

    Giambattista, Brian; McNairy, W. W.; Slough, C. G.; Johnson, A.; Bell, L. D.; Coleman, R. V.; Schneir, J.; Sonnenfeld, R.; Drake, B; Hansma, P K

    1987-01-01

    A scanning tunneling microscope (STM) can provide atomic-resolution images of solids covered with a variety of liquids, including cryogenic fluids, both polar and nonpolar solvents, conductive aqueous solutions, oils, and even greases. This short overview includes images of solids covered with liquid nitrogen, liquid helium, paraffin oil, silicone oil, microscope immersion oil, silicone vacuum grease, fluorocarbon grease, glycerol, and salt water. These images show atoms, charge-density waves...

  20. Use of booster fans in underground coal mining to advantage

    Institute of Scientific and Technical Information of China (English)

    Habibi A; Gillies A D S

    2011-01-01

    A booster fan is an underground main fan which is installed in series with a main surface fan and used to boost the air pressure of the ventilation to overcome mine resistance.Currently booster fans are used in several major coal mining countries including the United Kingdom,Australia,Poland and China.In the United States booster fans are prohibited in coal mines although they are used in several metal and non-metal mines.A study has been undertaken to examine alternatives for ventilating an underground room and pillar coal mine system.A feasibility study of a hypothetical situation has shown that current ventilation facilities are incapable of fulfilling mine air requirements in the future due to increased seam methane levels.A current ventilation network model has been prepared and projected to a mine five years plan.“Ventsim visual” software simulations of different possible ventilation options have been conducted in which varying methane levels are found at working faces.The software can also undertake financial simulations and project present value total costs for the options under study.Several scenarios for improving the ventilation situation such as improving main surface fans,adding intake shafts,adding exhaust shafts and utilizing booster fans have been examined.After taking into account the total capital and operating costs for the five years mine plan the booster fan scenarios are recommended as being the best alternatives for further serious consideration by the mine.The optimum option is a properly sized and installed booster fan system that can be used to create safe work conditions,maintain adequate air quantity with lowest cost,generate a reduction in energy consumption and decrease mine system air leakage.

  1. Female fans of men's football - a case study in Denmark

    DEFF Research Database (Denmark)

    Pfister, Gertrud Ursula; Lenneis, Verena; Mintert, Svenja-Maria

    2013-01-01

    Football is an invention by men for men, and today, the majority of players and fans are men. There is an abundance of literature on football and fandom; however, gender is mostly not an issue in these publications. Research about female football supporters and fans is very limited. This is also...... to a ‘man’s world’ and what are their roles in this ‘male environment’? The statements of interviewees revealed that female fans have to cope with a measure of sexism, but that they can adopt the men’s perspectives in order to be accepted as ‘authentic fans’. Other women reacted on men’s domination...

  2. Performance Study and CFD Predictions of a Ducted Fan System

    Science.gov (United States)

    Abrego, Anita I.; Chang, I-Chung; Bulaga, Robert W.; Rutkowski, Michael (Technical Monitor)

    2002-01-01

    An experimental investigation was completed in the NASA Ames 7 by 10-Foot Wind Tunnel to study the performance characteristics of a ducted fan. The goal of this effort is to study the effect of ducted fan geometry and utilize Computational Fluid Dynamics (CFD) analysis to provide a baseline for correlation. A 38-inch diameter, 10-inch chord duct with a five-bladed fixed-pitch fan was tested. Duct performance data were obtained in hover, vertical climb, and forward flight test conditions. This paper will present a description of the test, duct performance results and correlation with CFD predictions.

  3. Introduction of a Cooling-Fan Efficiency Index

    DEFF Research Database (Denmark)

    Schiavon, S.; Melikov, Arsen Krikor

    2009-01-01

    , while cooling capacity and efficiency of energy use are unknown. To address this knowledge gap, this paper introduces the cooling-fan efficiency (CFE) index, defined as the ratio between the cooling effect (measured with a thermal manikin) generated by the device and its power consumption. The index...... cooling effect and an index for determining fan efficiency, such as the CFE index proposed in this study, need to be developed. The cooling fans generate a nonuniform velocity field around occupants, which cannot be described with a single air-velociry value. Therefore, it is not clear how to apply...

  4. Characterization of dynamic change of Fan-delta reservoir properties in water-drive development

    Energy Technology Data Exchange (ETDEWEB)

    Wu Shenghe; Xiong Qihua; Liu Yuhong [Univ. of Petroleum Changping, Beijing (China)

    1997-08-01

    Fan-delta reservoir in Huzhuangji oil field of east China, is a typical highly heterogeneous reservoir. The oil field has been developed by water-drive for 10 years, but the oil recovery is less than 12%, and water cut is over 90%, resulting from high heterogeneity and serious dynamic change of reservoir properties. This paper aims at the study of dynamic change of reservoir properties in water-drive development. Through quantitative imaging analysis and mercury injection analysis of cores from inspection wells, the dynamic change of reservoir pore structure in water-drive development was studied. The results show that the {open_quotes}large pore channels{close_quotes} develop in distributary channel sandstone and become larger in water-drive development, resulting in more serious pore heterogeneity. Through reservoir sensitivity experiments, the rock-fluid reaction in water-drive development is studied. The results show the permeability of some distal bar sandstone and deserted channel sandstone becomes lower due to swelling of I/S clay minerals in pore throats. OD the other hand, the permeability of distributary channel and mouth bar sandstone become larger because the authigenic Koalinites in pore throats are flushed away with the increase of flow rate of injection water. Well-logging analysis of flooded reservoirs are used to study the dynamic change of reservoir properties in various flow units. The distribution of remaining oil is closely related to the types and distribution of flow units.

  5. COOLING FAN AND SYSTEM PERFORMANCE AND EFFICIENCY IMPROVEMENTS

    Energy Technology Data Exchange (ETDEWEB)

    Ronald Dupree

    2005-07-31

    Upcoming emissions regulations (Tiers 3, 4a and 4b) are imposing significantly higher heat loads on the cooling system than lesser regulated machines. This work was a suite of tasks aimed at reducing the parasitic losses of the cooling system, or improving the design process through six distinct tasks: 1. Develop an axial fan that will provide more airflow, with less input power and less noise. The initial plan was to use Genetic Algorithms to do an automated fan design, incorporating forward sweep for low noise. First and second generation concepts could not meet either performance or sound goals. An experienced turbomachinery designer, using a specialized CFD analysis program has taken over the design and has been able to demonstrate a 5% flow improvement (vs 10% goal) and 10% efficiency improvement (vs 10% goal) using blade twist only. 2. Fan shroud developments, using an 'aeroshroud' concept developed at Michigan State University. Performance testing at Michigan State University showed the design is capable of meeting the goal of a 10% increase in flow, but over a very narrow operating range of fan performance. The goal of 10% increase in fan efficiency was not met. Fan noise was reduced from 0 to 2dB, vs. a goal of 5dB at constant airflow. The narrow range of fan operating conditions affected by the aeroshroud makes this concept unattractive for further development at this time 3. Improved axial fan system modeling is needed to accommodate the numbers of cooling systems to be redesigned to meet lower emissions requirements. A CFD fan system modeling guide has been completed and transferred to design engineers. Current, uncontrolled modeling practices produce flow estimates in some cases within 5% of measured values, and in some cases within 25% of measured values. The techniques in the modeling guide reduced variability to the goal of + 5% for the case under study. 4. Demonstrate the performance and design versatility of a high performance fan. A

  6. Life, death and revival of debris-flow fans on Earth and Mars : fan dynamics and climatic inferences

    OpenAIRE

    Haas, T.

    2016-01-01

    Alluvial fans are ubiquitous landforms in high-relief regions on Earth and Mars. They have a semi-conical shape and are located at the transition between highlands and adjacent basins. Alluvial fans can form by a range of processes including debris flows, which are water-laden masses of soil and rock with volumetric sediment concentrations exceeding 40%. In this thesis, I aim to (1) unravel the formative dynamics of debris-flow fans and, building on these insights, to (2) reconstruct hydrolog...

  7. Is the turbidite facies association scheme valid for interpreting ancient submarine fan environments?

    Science.gov (United States)

    Shanmugam, G.; Damuth, J. E.; Moiola, R. J.

    1985-04-01

    Although turbidite facies reflect only processes of deposition, turbidite facies associations are routinely used to identify ancient submarine-fan subenvironments (e.g., upper fan, channel, lobe, etc.). The assumption that process of deposition also reflects environment of deposition may not be valid for the following reasons: (1) Mutti and Ricci Lucchi's facies association scheme for submarine fans has been developed exclusively from ancient turbidite sequences; however, the true relationship between such turbidite facies associations and related fan subenvironments has not been confirmed from modern fans; (2) individual channel-levee systems of many modern submarine fans are in many cases large enough to contain the entire ancient fan systems on which these facies associations are based; (3) large channel-levee systems comparable to those of modern fans have not been recognized in outcrops. Consequently, the validity of turbidite facies associations for interpreting ancient submarine-fan subenvironments must be considered tenuous until confirmed in modern fans.

  8. PLSS 2.5 Fan Design and Development

    Science.gov (United States)

    Quinn, Gregory; Carra, Michael; Converse, David; Chullen, Cinda

    2015-01-01

    NASA is building a high fidelity prototype of an advanced portable life support system (PLSS) as part of the Advanced Exploration Systems Program. This new PLSS, designated as PLSS 2.5, will advance component technologies and systems knowledge in order to inform a future flight program. The oxygen ventilation loop of its predecessor, PLSS 2.0, is driven by a centrifugal fan developed using specifications from the Constellation Program. PLSS technology and system parameters have matured to the point where the existing fan will not perform adequately for the new prototype. In addition, areas of potential improvement have been identified with the existing fan that could be addressed in a new design. As a result, a new fan was designed and tested for the PLSS 2.5.

  9. Autonomous Composite Fan Containment Integrity Monitoring (AUTOCONFIRM) System Project

    Data.gov (United States)

    National Aeronautics and Space Administration — New engine fan blade containment structures are being manufactured with advanced composite structures such that they can withstand blade-out events. The use of...

  10. Redefining genderswap fan fiction: A Sherlock case study

    Directory of Open Access Journals (Sweden)

    Ann McClellan

    2014-09-01

    Full Text Available Using BBC Sherlock (2010– fan fiction as case study, this article looks at how fans use and understand such concepts as biological sex and gender in genderswap fan fiction, arguing that the label often minimizes the importance of the physical body in determining gender identity. The label genderswap, most often used to describe stories where characters have become differently sexed, reflects and reinforces common cultural misunderstandings about differences between sex and gender. By teasing out definitions of genderswap, sex, gender, cisgender, and transgender, the article analyzes what genderswap includes and excludes from discussions of gender and identity within contemporary fan fiction, ultimately arguing for a broader conceptual understanding that grounds the genre within contemporary transgender theory.

  11. Low Cost/Low Noise Variable Pitch Ducted Fan Project

    Data.gov (United States)

    National Aeronautics and Space Administration — ACI proposes a design for a Propulsor (Low Cost/Low Noise Variable Pitch Ducted Fan) that has wide application in all sectors of Aviation. Propulsor hardware of this...

  12. Why do fans attend world Wrestling Entertainment? | Kruger | South ...

    African Journals Online (AJOL)

    South African Journal for Research in Sport, Physical Education and Recreation ... at a live Smackdown event in July 2011, which was part of the WWE's world tour. ... Therefore, marketing campaigns directed at these fans should be designed ...

  13. Gender constructions and negotiations of female football fans

    DEFF Research Database (Denmark)

    Lenneis, Verena; Pfister, Gertrud Ursula

    2015-01-01

    While both the media and the academic literature focus primarily on male fans, in particular on violence and the prevention of hooliganism, little is known about female football supporters. This is also true of Denmark, a country that is known for its high degree of gender equality. This article...... "hypermasculinity" nor "emphasised femininity" in their gender performances. Female fans do not only comply with and reproduce the rules of conduct in the stadium but also apply different forms of resistance against sexism and the domination of men in the stadium – both on the field and in the stands. The founding...... aims to give insight into gender constructions and negotiations of female football fans in the stands. Drawing on a social constructivist perspective to gender and Bourdieu's (1984) approaches to field, capital and habitus, we explored the experiences and opinions of female fans. The methods employed...

  14. Modeling and ecodesigning crossflow ventilation fans with Mathematica

    CERN Document Server

    Argentini, Gianluca

    2010-01-01

    The efficiency of a simple model of crossflow fan is maximized when the geometry depends on a design parameter. The flow field is numerically computed using a Galerkin method for solving a Poisson partial differential equation.

  15. Pathological effects of cyanobacteria on sea fans in southeast Florida.

    Science.gov (United States)

    Kiryu, Y; Landsberg, J H; Peters, E C; Tichenor, E; Burleson, C; Perry, N

    2015-07-01

    In early August 2008, observations by divers indicated that sea fans, particularly Gorgonia ventalina, Gorgonia flabellum, and Iciligorgia schrammi, were being covered by benthic filamentous cyanobacteria. From August 2008 through January 2009 and again in April 2009, tissue samples from a targeted G. ventalina colony affected by cyanobacteria and from a nearby, apparently healthy (without cyanobacteria) control colony, were collected monthly for histopathological examination. The primary cellular response of the sea fan to overgrowth by cyanobacteria was an increase in the number of acidophilic amoebocytes (with their granular contents dispersed) that were scattered throughout the coenenchyme tissue. Necrosis of scleroblasts and zooxanthellae and infiltration of degranulated amoebocytes were observed in the sea fan surface tissues at sites overgrown with cyanobacteria. Fungal hyphae in the axial skeleton were qualitatively more prominent in cyanobacteria-affected sea fans than in controls.

  16. Atomic energy

    CERN Multimedia

    1996-01-01

    Interviews following the 1991 co-operation Agreement between the Department of Atomic Energy (DAE) of the Government of India and the European Organization for Nuclear Research (CERN) concerning the participation in the Large Hadron Collider Project (LHC) . With Chidambaram, R, Chairman, Atomic Energy Commission and Secretary, Department of Atomic Energy, Department of Atomic Energy (DAE) of the Government of India and Professor Llewellyn-Smith, Christopher H, Director-General, CERN.

  17. Atom chips

    CERN Document Server

    Reichel, Jakob

    2010-01-01

    This book provides a stimulating and multifaceted picture of a rapidly developing field. The first part reviews fundamentals of atom chip research in tutorial style, while subsequent parts focus on the topics of atom-surface interaction, coherence on atom chips, and possible future directions of atom chip research. The articles are written by leading researchers in the field in their characteristic and individual styles.

  18. Extraction and preconcentration of copper from water, soils, lubricating oils and plant materials and its subsequent determination by atomic-absorption spectrophotometry.

    Science.gov (United States)

    Ejaz, M; Shamus-Zuha; Dil, W; Akhtar, A; Chaudhri, S A

    1981-07-01

    The extraction and preconcentration of the cupric thiocyanate complex with 4-(5-nonyl)pyridine in benzene is possible from neutral or up to 2M HCl, 0.5M HNO(3) or 0.25M H(2)SO(4) solutions. The method has considerable advantages over previously recommended extraction procedures because of selectivity, completeness of extraction in a single operation, short contact period, minimum amount of complexing agents needed and wide tolerance to various solution parameters. The complex formed from as little as 1 mug of copper can be extracted quantitatively into 1 ml of the organic phase from 500 ml of natural water. An extraction method is described which in combination with AAS can be used to determine copper in water, soils, fresh and used lubricating oils and plant-ash solutions down to the ng/ml or ng/g level.

  19. Noise Generation by Fans with Supersonic Tip Speeds

    Science.gov (United States)

    Glegg, Stewart; Envia, Edmane (Technical Monitor)

    2003-01-01

    Fan noise continues to be a significant issue for commercial aircraft engines and there still exists a requirement for improved understanding of the fundamental issues associated with fan noise source mechanisms. At the present time, most of the prediction methods identify the dominant acoustic sources to be associated with the stator vanes or blade trailing edges which are downstream of the fan face. However recent studies have shown that acoustic waves are significantly attenuated as they propagate upstream through a rotor, and if the appropriate corrections are applied, sound radiation from the engine inlet is significantly underpredicted. The prediction models can only be applied to fans with subsonic tip speeds. In contrast, most aircraft engines have fan tip speeds which are transonic and this implies an even higher attenuation for upstream propagating acoustic waves. Consequently understanding how sound propagates upstream through the fan is an important, and not well understood phenomena. The objective of this study is to provide improved insight into the upstream propagation effects through a rotor which are relevant to full scale engines. The focus of this study is on broadband fan noise generated by boundary layer turbulence interacting with the trailing edges of the fan blades. If this source mechanism is important upstream of the fan, the sound must propagate upstream through a transonic non uniform flow which includes large gradients and non linearities. Developing acoustic propagation models in this type of flow is challenging and currently limited to low frequency applications, where the frequency is of the same order as the blade passing frequency of the fan. For trailing edge noise, much higher frequencies are relevant and so a suitable approach needs to be developed, which is not limited by an unacceptably large computational effort. In this study we are in the process of developing a computational method which applies for the high frequencies of

  20. Should electric fans be used during a heat wave?

    Science.gov (United States)

    Jay, Ollie; Cramer, Matthew N; Ravanelli, Nicholas M; Hodder, Simon G

    2015-01-01

    Heat waves continue to claim lives, with the elderly and poor at greatest risk. A simple and cost-effective intervention is an electric fan, but public health agencies warn against their use despite no evidence refuting their efficacy in heat waves. A conceptual human heat balance model can be used to estimate the evaporative requirement for heat balance, the potential for evaporative heat loss from the skin, and the predicted sweat rate, with and without an electrical fan during heat wave conditions. Using criteria defined by the literature, it is clear that fans increase the predicted critical environmental limits for both the physiological compensation of endogenous/exogenous heat, and the onset of cardiovascular strain by an air temperature of ∼3-4 °C, irrespective of relative humidity (RH) for the young and elderly. Even above these critical limits, fans would apparently still provide marginal benefits at air temperatures as high as 51.1 °C at 10%RH for young adults and 48.1 °C at 10%RH for the elderly. Previous concerns that dehydration would be exacerbated with fan use do not seem likely, except under very hot (>40 °C) and dry (conditions, when predicted sweat losses are only greater with fans by a minor amount (∼20-30 mL/h). Relative to the peak outdoor environmental conditions reported during ten of the most severe heat waves in recent history, fan use would be advisable in all of these situations, even when reducing the predicted maximum sweat output for the elderly. The protective benefit of fans appears to be underestimated by current guidelines. Copyright © 2014 Elsevier Ltd and The Ergonomics Society. All rights reserved.

  1. On the Optimal Selection of Electrical Machines Fans

    Directory of Open Access Journals (Sweden)

    Mădălin Costin

    2014-09-01

    Full Text Available In this paper an analytic relationship for electrical machine fan design has been developed. In the particularly case of salient poles synchronous machine (with salient poles – for electromagnetic field excitation or surface mounded permanent magnet, this approach allowed to express the fan power as a function of machine middle axe air gap. This analytic foundation developed may leads to different optimization criteria as specific active materials or costs. Numerical simulations confirm our approach.

  2. Sport Fan Motivation: Are You Going To The Game?

    OpenAIRE

    Johannes A. Wiid; Cant, Michael C.

    2015-01-01

    Every individual or group consume sporting events for different reasons and are therefore motivated in different ways. People consuming sport events can be referred to as sport fans, someone who is enthusiastic about a particular sport, an athlete or someone who is motivated to make the effort to attend a live sporting event. Research on sport consumption motivation had led to the development of the Sport Fan Motivation Scale (SFMS), which consists of eight motives namely, eustress, self-este...

  3. Investigation of flow separation in a transonic-fan linear cascade using visualization methods

    Energy Technology Data Exchange (ETDEWEB)

    Lepicovsky, J. [ASRC Aerospace Corporation, NASA GRC, Cleveland, OH (United States)

    2008-06-15

    An extensive experimental study into the nature of the separated flows on the blade suction surface of modern transonic fans is described in this paper. The study was a subtask of a larger experimental effort focused on blade flutter excited by flow separation in the blade tip region. The tip sections of airfoils on transonic fan blades are designed for precompression and consequently they differ from sections on the rest of the blade. The blade tip section was modeled by a low aspect ratio blade and therefore most of the blade tested was exposed to the secondary flow effects. The aim of this work was to supply reliable data on flow separation on transonic fan blades for validation of future analytical studies. The experimental study focused on two visualization techniques: surface flow visualization using dye oils and schlieren (and shadowgraph) flow visualization. The following key observations were made during the study. For subsonic inlet flow, the flow on the suction surface of the blade was separated over a large portion of the blade, and the separated area increased with increasing inlet Mach number. For the supersonic inlet flow condition, the flow was attached from the leading edge up to the point where a bow shock from the upper neighboring blade imposed on the blade surface. Downstream, there was a separated flow region in which air flowed in the direction opposite the inlet flow. Finally, past the separated flow region, the flow reattached to the blade surface. For subsonic inlet flow, the low cascade solidity resulted in an increased area of separated flow. For supersonic flow conditions, the low solidity resulted in an improvement in flow over the suction surface. (orig.)

  4. Investigation of flow separation in a transonic-fan linear cascade using visualization methods

    Science.gov (United States)

    Lepicovsky, J.

    2008-06-01

    An extensive experimental study into the nature of the separated flows on the blade suction surface of modern transonic fans is described in this paper. The study was a subtask of a larger experimental effort focused on blade flutter excited by flow separation in the blade tip region. The tip sections of airfoils on transonic fan blades are designed for precompression and consequently they differ from sections on the rest of the blade. The blade tip section was modeled by a low aspect ratio blade and therefore most of the blade tested was exposed to the secondary flow effects. The aim of this work was to supply reliable data on flow separation on transonic fan blades for validation of future analytical studies. The experimental study focused on two visualization techniques: surface flow visualization using dye oils and schlieren (and shadowgraph) flow visualization. The following key observations were made during the study. For subsonic inlet flow, the flow on the suction surface of the blade was separated over a large portion of the blade, and the separated area increased with increasing inlet Mach number. For the supersonic inlet flow condition, the flow was attached from the leading edge up to the point where a bow shock from the upper neighboring blade imposed on the blade surface. Downstream, there was a separated flow region in which air flowed in the direction opposite the inlet flow. Finally, past the separated flow region, the flow reattached to the blade surface. For subsonic inlet flow, the low cascade solidity resulted in an increased area of separated flow. For supersonic flow conditions, the low solidity resulted in an improvement in flow over the suction surface.

  5. Simulation of fan topography and soil profile using a coupled soilscape-landscape evolution model

    Science.gov (United States)

    Welivitiya, Dimuth; Willgoose, Garry; Hancock, Greg

    2017-04-01

    In this study the evolution of a fluvial fan, its topography and soil profile grading under erosion and deposition and soil profile weathering was simulated using SSPAM coupled soil-landscape evolution model. A constant rainfall was simulated on a synthetic landform and a fluvial fan depositional structure was allowed to form at the latter part of the landform. At each time step the geomorphological and particle size distribution information of the fan was recorded. Using this recorded information, the evolutionary characteristics of the fan as well as the surface and subsurface sediment characteristics was examined and compared with experimental and field observation data. Different fan profile sections were also derived from the recorded data and analysed. The simulation produced a fluvial fan semicircular in shape, with concave up long profiles and convex up cross profiles. The surface sediment sizes of the simulated fan were coarsest near the fan apex and fines toward the fan toe with coarse grained sediment filaments extending radially from the fan apex. These geomorphological features and surface sediment distribution agrees well with field observations of natural fans. The results of the simulation also show that the fan develops as a result of the channel bringing sediments in to the fan and periodically changing its path due to steepening of channel gradient by sediment deposition. The position of the channel is fixed at the fan apex and the channel path constantly changes along any radial direction form the fan apex. This process is remarkably similar to the process of "Fan head trenching" described in literature which is the dominant process in fluvial fan development in the field. Finally, the analysis of fan cross-sections revealed complex sediment layering patterns in the fan profile. The simulation results of the SSSPAM coupled soilscape-landscape evolution model provide qualitatively correct geomorphological and sedimentary characterization of the

  6. Experimental and Numerical Investigation of a 60cm Diameter Bladeless Fan

    OpenAIRE

    mohammad jafari; Hossein Afshin; Bijan Farhanieh; Hamidreza bozorgasareh

    2016-01-01

    Bladeless fan is a novel type of fan with an unusual geometry and unique characteristics. This type of fan has been recently developed for domestic applications in sizes typically up to 30cm diameter. In the present study, a Bladeless fan with a diameter of 60cm was designed and constructed, in order to investigate feasibility of its usage in various industries with large dimensions. Firstly, flow field passed through this fan was studied by 3D modeling. Aerodynamic and aeroacoust...

  7. Damage-Tolerant Fan Casings for Jet Engines

    Science.gov (United States)

    2006-01-01

    All turbofan engines work on the same principle. A large fan at the front of the engine draws air in. A portion of the air enters the compressor, but a greater portion passes on the outside of the engine this is called bypass air. The air that enters the compressor then passes through several stages of rotating fan blades that compress the air more, and then it passes into the combustor. In the combustor, fuel is injected into the airstream, and the fuel-air mixture is ignited. The hot gasses produced expand rapidly to the rear, and the engine reacts by moving forward. If there is a flaw in the system, such as an unexpected obstruction, the fan blade can break, spin off, and harm other engine components. Fan casings, therefore, need to be strong enough to contain errant blades and damage-tolerant to withstand the punishment of a loose blade-turned-projectile. NASA has spearheaded research into improving jet engine fan casings, ultimately discovering a cost-effective approach to manufacturing damage-tolerant fan cases that also boast significant weight reduction. In an aircraft, weight reduction translates directly into fuel burn savings, increased payload, and greater aircraft range. This technology increases safety and structural integrity; is an attractive, viable option for engine manufacturers, because of the low-cost manufacturing; and it is a practical alternative for customers, as it has the added cost saving benefits of the weight reduction.

  8. Potential Global Benefits of Improved Ceiling Fan Energy Efficiency

    Energy Technology Data Exchange (ETDEWEB)

    Sathaye, Nakul [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Phadke, Amol [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Shah, Nihar [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Letschert, Virginie [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States)

    2012-10-31

    Ceiling fans contribute significantly to residential electricity consumption, both in an absolute sense and as a proportion of household consumption in many locations, especially in developing countries in warm climates. However, there has been little detailed assessment of the costs and benefits of efficiency improvement options for ceiling fans and the potential resulting electricity consumption and greenhouse gas (GHG) emissions reductions. We analyze the costs and benefits of several options to improve the efficiency of ceiling fans and assess the global potential for electricity savings and GHG emission reductions with more detailed assessments for India, China, and the U.S. We find that ceiling fan efficiency can be cost-effectively improved by at least 50% using commercially available technology. If these efficiency improvements are implemented in all ceiling fans sold by 2020, 70 terrawatt hours per year (TWh/year) could be saved and 25 million metric tons of carbon dioxide (CO2) emissions per year could be avoided, globally. We assess how policies and programs such as standards, labels, and financial incentives can be used to accelerate the adoption of efficient ceiling fans in order to realize this savings potential.

  9. COOLING FAN AND SYSTEM PERFORMANCE AND EFFICIENCY IMPROVEMENTS

    Energy Technology Data Exchange (ETDEWEB)

    Ronald Dupree

    2005-07-31

    Upcoming emissions regulations (Tiers 3, 4a and 4b) are imposing significantly higher heat loads on the cooling system than lesser regulated machines. This work was a suite of tasks aimed at reducing the parasitic losses of the cooling system, or improving the design process through six distinct tasks: 1. Develop an axial fan that will provide more airflow, with less input power and less noise. The initial plan was to use Genetic Algorithms to do an automated fan design, incorporating forward sweep for low noise. First and second generation concepts could not meet either performance or sound goals. An experienced turbomachinery designer, using a specialized CFD analysis program has taken over the design and has been able to demonstrate a 5% flow improvement (vs 10% goal) and 10% efficiency improvement (vs 10% goal) using blade twist only. 2. Fan shroud developments, using an 'aeroshroud' concept developed at Michigan State University. Performance testing at Michigan State University showed the design is capable of meeting the goal of a 10% increase in flow, but over a very narrow operating range of fan performance. The goal of 10% increase in fan efficiency was not met. Fan noise was reduced from 0 to 2dB, vs. a goal of 5dB at constant airflow. The narrow range of fan operating conditions affected by the aeroshroud makes this concept unattractive for further development at this time 3. Improved axial fan system modeling is needed to accommodate the numbers of cooling systems to be redesigned to meet lower emissions requirements. A CFD fan system modeling guide has been completed and transferred to design engineers. Current, uncontrolled modeling practices produce flow estimates in some cases within 5% of measured values, and in some cases within 25% of measured values. The techniques in the modeling guide reduced variability to the goal of + 5% for the case under study. 4. Demonstrate the performance and design versatility of a high performance fan. A

  10. Broadband Liner Optimization for the Source Diagnostic Test Fan

    Science.gov (United States)

    Nark, Douglas M.; Jones, Michael G.

    2012-01-01

    The broadband component of fan noise has grown in relevance with the utilization of increased bypass ratio and advanced fan designs. Thus, while the attenuation of fan tones remains paramount, the ability to simultaneously reduce broadband fan noise levels has become more appealing. This paper describes a broadband acoustic liner optimization study for the scale model Source Diagnostic Test fan. Specifically, in-duct attenuation predictions with a statistical fan source model are used to obtain optimum impedance spectra over a number of flow conditions for three liner locations in the bypass duct. The predicted optimum impedance information is then used with acoustic liner modeling tools to design liners aimed at producing impedance spectra that most closely match the predicted optimum values. Design selection is based on an acceptance criterion that provides the ability to apply increased weighting to specific frequencies and/or operating conditions. Typical tonal liner designs targeting single frequencies at one operating condition are first produced to provide baseline performance information. These are followed by multiple broadband design approaches culminating in a broadband liner targeting the full range of frequencies and operating conditions. The broadband liner is found to satisfy the optimum impedance objectives much better than the tonal liner designs. In addition, the broadband liner is found to provide better attenuation than the tonal designs over the full range of frequencies and operating conditions considered. Thus, the current study successfully establishes a process for the initial design and evaluation of novel broadband liner concepts for complex engine configurations.

  11. THz Beam Shaper Realizing Fan-Out Patterns

    Science.gov (United States)

    Liebert, K.; Rachon, M.; Siemion, A.; Suszek, J.; But, D.; Knap, W.; Sypek, M.

    2017-08-01

    Fan-out elements create an array of beams radiating at particular angles along the propagation axis. Therefore, they are able to form a matrix of equidistant spots in the far-field diffraction region. In this work, we report on the first fan-out structures designed for the THz range of radiation. Two types of light-dividing fan-out structures are demonstrated: (i) the 3×1 matrix fan-out structure based on the optimized binary phase grating and (ii) the 3×3 fan-out structure designed on the basis of the well-known Dammann grating. The structures were generated numerically and manufactured using the 3D printing technique with polyamide PA12. To obtain equal powers and symmetry of diffracted beams, the computer-aided optimization algorithm was used. Diffractive optical elements designed for 140 and 282 GHz were evaluated experimentally at both these frequencies using illumination with the wavefront coming from the point-like source. Described fan-out elements formed uniform intensity and equidistant energy distribution in agreement with the numerical simulations.

  12. "The florals": Female fans over 50 in the Sherlock fandom

    Directory of Open Access Journals (Sweden)

    Line Nybro Petersen

    2017-03-01

    Full Text Available This article uses e-mail interviews with nine female fans to explore what it means to be a fan over the age of 50 of the popular BBC drama Sherlock (2010–. The research aims to better understand the role of fandom in later life, in particular how the participants in this study negotiate their perceptions of their subjective age in relation to being a fan in this part of their life course. This study combines theory on cultural gerontology with fan studies and mediatization theory in order to understand the dynamics and processes that guide fans' negotiations of subjective age as well as the role of fan practices and the affordances of social media in these processes. I argue that fandom, as a manifestation of a mediatized culture, augments the relevance of subjective age and informs the way in which participants in middle and later life perceive and negotiate their own subjective age specifically in relation to fandom as youth culture, women's passion, and creativity.

  13. Fan Ky不等式的一个改进%A Refinement of Fan Ky's Inequality

    Institute of Scientific and Technical Information of China (English)

    周昱; 高明哲

    2007-01-01

    利用改进的H(o)lder不等式并借助于正交矩阵的行列式的积分表示法建立了Fan Ky不等式的一个有意义的改进.当A,B为n阶非奇异矩阵时,给出了新创建不等式的一个推广.特别当n=1时,得到了Young不等式的一个很强的结果.

  14. Dynamic Bowtie for Fan-beam CT

    CERN Document Server

    Liu, Fenglin; Cong, Wenxiang; Hsieh, Scott; Pelc, Norbert

    2013-01-01

    A bowtie is a filter used to shape an x-ray beam and equalize its flux reaching different detector channels. For development of spectral CT with energy-discriminative photon-counting (EDPC) detectors, here we propose and evaluate a dynamic bowtie for performance optimization based on a patient model or a scout scan. Our dynamic bowtie modifies an x-ray beam intensity profile by mechanical rotation and adaptive adjustment of the x-ray source flux. First, a mathematical model for dynamic bowtie filtering is established for an elliptical section in fan-beam geometry, and the contour of the optimal bowtie is derived. Then, numerical simulation is performed to compare the performance of the dynamic bowtie in the cases of an ideal phantom and a realistic cross-section relative to the counterparts without any bowtie and with a fixed bowtie respectively. Our dynamic bowtie can equalize the expected numbers of photons in the case of an ideal phantom. In practical cases, our dynamic bowtie can effectively reduce the dy...

  15. Characterisation of fan-beam collimators.

    Science.gov (United States)

    Pareto, D; Pavía, J; Falcón, C; Juvells, I; Cot, A; Ros, D

    2001-02-01

    Fan-beam collimators offer a good balance between resolution and noise. The collimator response may be included in iterative reconstruction algorithms in order to improve single-photon emission tomography (SPET) resolution. To this end, accurate determination of the focal region and characterisation of the collimator response as a function of the source co-ordinates must be performed. In this paper, a method to characterise fanbeam collimators is evaluated. First, we calculated the real focal region and the accuracy of the collimator convergence. Then, we confirmed the hypothesis that Gaussian distributions adequately fit the collimator responses, although no individualised treatment was performed for the tails of detector response which are associated with scattering and septal penetration. Finally, analytical functions were used to model the resolution and sensitivity. The parameter values in these functions were obtained from experimental measures by non-linear regression fitting. Our findings show differences of 1.43% between nominal and real focal length and standard deviations of 2.5 mm in the x-direction and 7.1 mm in the y-direction for the focal convergence. The correlation coefficients between experimental and predicted values were 0.994 for resolution and 0.991 for sensitivity. As a consequence, the proposed method can be used to characterise the collimator response.

  16. Atomic polarizabilities

    Energy Technology Data Exchange (ETDEWEB)

    Safronova, M. S. [Department of Physics and Astronomy, University of Delaware, Newark, DE 19716 (United States); Mitroy, J. [School of Engineering, Charles Darwin University, Darwin NT 0909 (Australia); Clark, Charles W. [Joint Quantum Institute, National Institute of Standards and Technology and the University of Maryland, Gaithersburg, Maryland 20899-8410 (United States); Kozlov, M. G. [Petersburg Nuclear Physics Institute, Gatchina 188300 (Russian Federation)

    2015-01-22

    The atomic dipole polarizability governs the first-order response of an atom to an applied electric field. Atomic polarization phenomena impinge upon a number of areas and processes in physics and have been the subject of considerable interest and heightened importance in recent years. In this paper, we will summarize some of the recent applications of atomic polarizability studies. A summary of results for polarizabilities of noble gases, monovalent, and divalent atoms is given. The development of the CI+all-order method that combines configuration interaction and linearized coupled-cluster approaches is discussed.

  17. Review: Bettina Fritzsche (2003. Pop-Fans. Studie einer Mädchenkultur [Pop-Fans: Study of a Girl Culture

    Directory of Open Access Journals (Sweden)

    Lothar Mikos

    2006-05-01

    Full Text Available This study focuses on the "girl culture" created by fans of boy groups and girl groups. The central case study is used to examine fan practices as cultural practices using reconstructive and documentary methodologies, and to assess the normative demands placed on young people. The study centers on the question of gender socialization by mediated symbolic resources, and shows that fan culture is a self-determined space in which girls can negotiate normative demands and engage with questions of gender, sexuality and the body, testing conformity and obstinacy. Fan activities are presented as part of the self-empowerment of girls. The study makes an important contribution to the research of a specific girl culture. It shows in a brilliant way how media representations are used as symbolic material in everyday cultural practices. URN: urn:nbn:de:0114-fqs0603187

  18. Ultracold atoms on atom chips

    DEFF Research Database (Denmark)

    Krüger, Peter; Hofferberth, S.; Haller, E.

    2005-01-01

    Miniaturized potentials near the surface of atom chips can be used as flexible and versatile tools for the manipulation of ultracold atoms on a microscale. The full scope of possibilities is only accessible if atom-surface distances can be reduced to microns. We discuss experiments in this regime...

  19. Investigation of Flow Separation in a Transonic-fan Linear Cascade Using Visualization Methods

    Science.gov (United States)

    Lepicovsky, Jan; Chima, Rodrick V.; Jett, Thomas A.; Bencic, Timothy J.; Weiland, Kenneth E.

    2000-01-01

    An extensive study into the nature of the separated flows on the suction side of modem transonic fan airfoils at high incidence is described in the paper. Suction surface.flow separation is an important flow characteristic that may significantly contribute to stall flutter in transonic fans. Flutter in axial turbomachines is a highly undesirable and dangerous self-excited mode of blade oscillations that can result in high cycle fatigue blade failure. The study basically focused on two visualization techniques: surface flow visualization using dye oils, and schlieren (and shadowgraph) flow visualization. The following key observations were made during the study. For subsonic inlet flow, the flow on the suction side of the blade is separated over a large portion of the blade, and the separated area increases with increasing inlet Mach number. For the supersonic inlet flow condition, the flow is attached from the leading edge up to the point where a bow shock from the upper neighboring blade hits the blade surface. Low cascade solidity, for the subsonic inlet flow, results in an increased area of separated flow. For supersonic flow conditions, a low solidity results in an improvement in flow over the suction surface. Finally, computational results modeling the transonic cascade flowfield illustrate our ability to simulate these flows numerically.

  20. Evaluation of Uncertainty of Measurement for Cadmium from Fish Oil by Atomic Absorption Spectrometry%原子吸收光谱法测定鱼油中镉的不确定度评定

    Institute of Scientific and Technical Information of China (English)

    杨玳; 黄舒丽

    2012-01-01

    Objective To establish a method for the uncertainty evaluation of measurement of cadmium from fish oil. Methods According to the relevant regulation of Evaluation and Expression of Uncertainty in Measurement and referring to Guidance on Evaluating the. Uncertainty in Chemical Analysis, the content of cadmium from fish oil was measured by the graphite furnace atomic absorption spectrometry, and the uncertainty was analyzed and evaluated. Results The combined relative standard uncertainty was 0.20 μg/kg, the expanded uncertainty was 0.40 μg/kg. Conclusion By using the method of uncertainty evaluation, the key procedure can be found and controlled in the process of measurement. The operation under the specifications during measuring process can reduce the uncertainty and make the determination results more reliable.%目的 建立测定鱼油中镉不确定度的评定方法.方法 根据《测量不确定度评定与表示》的有关规定,参考《化学分析中不确定度的评估指南》,采用石墨炉原子吸收光谱法测定鱼油中镉含量并分析与评定其不确定度.结果 合成标准不确定度0.20μg/kg,扩展不确定度0.40μg/kg.结论 运用此不确定度评定方法控制测量过程中的关键步骤,严格按照操作规范,可有效地减低引入的不确定度,使测定结果更可靠.

  1. Genes2FANs: connecting genes through functional association networks

    Directory of Open Access Journals (Sweden)

    Dannenfelser Ruth

    2012-07-01

    Full Text Available Abstract Background Protein-protein, cell signaling, metabolic, and transcriptional interaction networks are useful for identifying connections between lists of experimentally identified genes/proteins. However, besides physical or co-expression interactions there are many ways in which pairs of genes, or their protein products, can be associated. By systematically incorporating knowledge on shared properties of genes from diverse sources to build functional association networks (FANs, researchers may be able to identify additional functional interactions between groups of genes that are not readily apparent. Results Genes2FANs is a web based tool and a database that utilizes 14 carefully constructed FANs and a large-scale protein-protein interaction (PPI network to build subnetworks that connect lists of human and mouse genes. The FANs are created from mammalian gene set libraries where mouse genes are converted to their human orthologs. The tool takes as input a list of human or mouse Entrez gene symbols to produce a subnetwork and a ranked list of intermediate genes that are used to connect the query input list. In addition, users can enter any PubMed search term and then the system automatically converts the returned results to gene lists using GeneRIF. This gene list is then used as input to generate a subnetwork from the user’s PubMed query. As a case study, we applied Genes2FANs to connect disease genes from 90 well-studied disorders. We find an inverse correlation between the counts of links connecting disease genes through PPI and links connecting diseases genes through FANs, separating diseases into two categories. Conclusions Genes2FANs is a useful tool for interpreting the relationships between gene/protein lists in the context of their various functions and networks. Combining functional association interactions with physical PPIs can be useful for revealing new biology and help form hypotheses for further experimentation. Our

  2. Mining Study of Oil Atomic Emission Spectrum Data of Certain Diesel Engine%某型柴油机润滑油发射光谱数据挖掘研究*

    Institute of Scientific and Technical Information of China (English)

    张乔斌; 张春辉; 朱爱芳

    2014-01-01

    Atomic emission spectroscopy is one of the most widely used techniques for oil analysis in the world now .In order to deeply mine the relation between the concentration of wearing elements of diesel engine and its loads ,cylinders'clearances and runtime after renewing oil ,a simulation model and a prediction model of Fe concentration of a type of six cyl‐inder diesel engine are established by applying neural network .The engine set up seven different working conditions and measured concentration of sixty‐nine oil samples .The results show that the relative errors of the simulation value of the 69 samples are within less than 15% .The absolute errors of prediction value of the 19 samples are lower than the acceptable ac‐curacy indices and the relative errors of 84% samples are within 15% .It is proved that Fe concentration can be predicted ef‐fectively by Neural Network algorithm .%油料原子发射光谱仪是目前国内外广泛应用的油液分析技术之一。为了深入挖掘某型柴油机润滑油中磨损元素的浓度与柴油机负荷、气缸间隙和运行时间之间的对应关系,应用神经网络建立了某型六缸柴油机主要磨损元素 Fe的浓度仿真模型和预测模型。柴油机设置了7种工况,测量了69个油样。仿真模型中,69个油样仿真值的相对误差均小于15%;预测模型中,19个油样预测值的绝对误差均小于光谱仪精确度值,且84%的油样预测值的相对误差小于15%。预测结果表明:神经网络算法能较好地预测Fe元素浓度。

  3. Palm Oil

    Science.gov (United States)

    Palm oil is obtained from the fruit of the oil palm tree. Palm oil is used for preventing vitamin A deficiency, cancer, ... blood pressure, high cholesterol, and cyanide poisoning. Palm oil is used for weight loss and increasing the ...

  4. Diesel oil

    Science.gov (United States)

    Oil ... Diesel oil ... Diesel oil poisoning can cause symptoms in many parts of the body. EYES, EARS, NOSE, AND THROAT Loss of ... most dangerous effects of hydrocarbon (such as diesel oil) poisoning are due to inhaling the fumes. NERVOUS ...

  5. Sedimentology and hydrocarbon habitat of the submarine-fan deposits of the Central Carpathian Paleogene Basin (NE Slovakia)

    Energy Technology Data Exchange (ETDEWEB)

    Sotak, J. [Slovak Academy of Sciences, Banska Bystrica (Slovakia). Geological Institute; Pereszlenyi, M. [VVNP Research Oil Company for Exploration and Production, Bratislava (Slovakia); Marschalko, R.; Starek, D. [Slovak Academy of Sciences, Bratislava (Slovakia). Geological Institute; Milicka, J. [Comenius University, Bratislava (Slovakia). Dept. of Geochemistry

    2001-01-01

    The Central Carpathian Paleogene Basin accommodates a subsiding area of the destructive plate-margin. The basin history comprises marginal faulting and alluvial fan accumulation (E{sub 2}); transgressive onlap by shoreface sediments and carbonate platform deposits (E{sub 2}); glacio-eustatic regression induced by cooling (Terminal Eocene Event); forced regression, tectonic subsidence and growth-fault accumulation of basin-floor and slope fans (E{sub 3}); decelerating subsidence, aggradation and sea-level rising during the mud-rich deposition (O{sub 1}); high-magnitude drop in sea-level (Mid-Oligocene Event), retroarc backstep of depocenters and lowstand accumulation of sand-rich fans and suprafans (O{sub 2}-M{sub 1}); subduction-related shortening and basin inversion along the northern margins affected by backthrusting and transpressional deformation (O{sub 2}-M{sub 1}). The basin-fill sequence has poor (TOC {<=} 0.5%) to fair (TOC < 1.0%) quality of source rocks. Maturity of OM ranges from initial to relic stage of HC generation. Paleogene rock-extracts display a good correlation with scarce trapped oils. 'The presence of solid bitumens and HC-rich fluid inclusions indicates overpressure conditions during HC generation and migration. Potential HC reservoirs can be expected in porous lithologies (scarp breccias), in basement highs and traps related to backthrusting, fault-propagation folding and strike-slip tectonics. (author)

  6. Improved recovery from Gulf of Mexico reservoirs. Volume I (of 4): Task 1, conduct research on mud-rich submarine fans. Final report, February 14, 1995--October 13, 1996

    Energy Technology Data Exchange (ETDEWEB)

    Kimbrell, W.C.; Bassiouni, Z.A.; Bourgoyne, A.T.

    1997-01-13

    The objective for this portion of the research involved conducting field studies and laboratory investigations to develop and refine models for mud-rich submarine fan architectures used by seismic analysis and reservoir engineers. These research aspects have been presented in two papers as follows: (1) Bouma, A.H., {open_quotes}Review of Fine-Grained Submarine Fans and Turbidite Systems{close_quotes}; (2) Kirkova, J.T. and Lorenzo, J.M., {open_quotes}Synthetic Seismic Modeling of Measured Submarine Fans Sections, Case Study of the Tanqua Complex, Karoo, South Africa{close_quotes} The {open_quotes}Review of Fine-Grained Submarine Fans and Turbidite Systems{close_quotes} by Arnold Bouma discusses research targeted toward stimulating an increase in oil and gas recovery by developing new and improved geological understanding. The {open_quotes}Synthetic Seismic Modeling of Measured Submarine Fan Sections, Case Study of the Tanqua Complex, Karoo, South Africa{close_quotes} by J.T. Kirkova and J.M. Lorenso discusses the limitations of verticle resolution and how this affects the interpretation and characterization of submarine fan complexes.

  7. Numerical and experimental investigation on aerodynamic performance of small axial flow fan with hollow blade root

    Science.gov (United States)

    Li, Zhang; Jin, Yingzi; Huashu, Dou; Yuzhen, Jin

    2013-10-01

    To reduce the influence of adverse flow conditions at the fan hub and improve fan aerodynamic performance, a modification of conventional axial fan blades with numerical and experimental investigation is presented. Hollow blade root is manufactured near the hub. The numerical and experimental results show that hollow blade root has some effect on the static performance. Static pressure of the modified fan is generally the same with that of the datum fan, while, the efficiency curve of the modified fan has a different trend with that of the datum fan. The highest efficiency of the modified fan is 10% greater than that of the datum fan. The orthogonal experimental results of fan noise show that hollow blade root is a feasible method of reducing fan noise, and the maximum value of noise reduction is about 2 dB. The factors affecting the noise reduction of hollow blade root are in the order of importance as follows: hollow blade margin, hollow blade height and hollow blade width. The much smoother pressure distribution of the modified fan than that of the datum fan is the main mechanism of noise reduction of hollow blade root. The research results will provide the proof of the parameter optimization and the structure design for high performance and low noise small axial fans.

  8. Fan-structure wave as a source of earthquake instability

    Science.gov (United States)

    Tarasov, Boris

    2015-04-01

    Today frictional shear resistance along pre-existing faults is considered to be the lower limit on rock shear strength at confined compression corresponding to the seismogenic layer. This determines the lithospheric strength and the primary earthquake mechanism associated with frictional stick-slip instability on pre-existing faults. This paper introduces a recently identified shear rupture mechanism providing a paradoxical feature of hard rocks - the possibility of shear rupture propagation through the highly confined intact rock mass at shear stress levels significantly less than frictional strength. In the new mechanism the rock failure, associated with consecutive creation of small slabs (known as 'domino-blocks') from the intact rock in the rupture tip, is driven by a fan-shaped domino structure representing the rupture head. The fan-head combines such unique features as: extremely low shear resistance (below the frictional strength), self-sustaining stress intensification in the rupture tip (providing easy formation of new domino-blocks), and self-unbalancing conditions in the fan-head (making the failure process inevitably spontaneous and violent). An important feature of the fan-mechanism is the fact that for the initial formation of the fan-structure an enhanced local shear stress is required, however, after completion of the fan-structure it can propagate as a dynamic wave through intact rock mass at shear stresses below the frictional strength. Paradoxically low shear strength of pristine rocks provided by the fan-mechanism determines the lower limit of the lithospheric strength and favours the generation of new faults in pristine rocks in preference to frictional stick-slip instability along pre-existing faults. The new approach reveals an alternative role of pre-existing faults in earthquake activity: they represent local stress concentrates in pristine rock adjoining the fault where special conditions for the fan-mechanism nucleation are created

  9. Research, development, and testing of a prototype two-stage low-input rate oil burner for variable output heating system applications

    Energy Technology Data Exchange (ETDEWEB)

    Krajewski, R.F.; Butcher, T.A. [Brookhaven National Labs., Upton, NY (United States)

    1997-09-01

    The use of a Two-Stage Fan Atomized Oil Burner (TSFAB) in space and water heating applications will have dramatic advantages in terms of it`s potential for a high Annual Fuel Utilization Efficiency (AFUE) and/or Energy Factor (EF) rating for the equipment. While demonstrations of a single rate burner in an actual application have already yielded sufficient confidence that space and domestic heating loads can be met at a single low firing rate, this represents only a narrow solution to the diverse nature of building space heating and domestic water loads that the industry must address. The mechanical development, proposed control, and testing of the Two-Stage burner is discussed in terms of near term and long term goals.

  10. Numerical Study of Transition of an Annular Lift Fan Aircraft

    Directory of Open Access Journals (Sweden)

    Yun Jiang

    2016-09-01

    Full Text Available The present study aimed at studying the transition of annular lift fan aircraft through computational fluid dynamics (CFD simulations. The oscillations of lift and drag, the optimization for the figure of merit, and the characteristics of drag, yawing, rolling and pitching moments in transition are studied. The results show that a two-stage upper and lower fan lift system can generate oscillations of lift and drag in transition, while a single-stage inner and outer fan lift system can eliminate the oscillations. The characteristics of momentum drag of the single-stage fans in transition are similar to that of the two-stage fans, but with the peak of drag lowered from 0.63 to 0.4 of the aircraft weight. The strategy to start transition from a negative angle of attack −21° further reduces the peak of drag to 0.29 of the weight. The strategy also reduces the peak of pitching torque, which needs upward extra thrusts of 0.39 of the weight to eliminate. The peak of rolling moment in transition needs differential upward thrusts of 0.04 of the weight to eliminate. The requirements for extra thrusts in transition lead to a total thrust–weight ratio of 0.7, which makes the aircraft more efficient for high speed cruise flight (higher than 0.7 Ma.

  11. Bifurcation analysis of fan casing under rotating air flow excitation

    Institute of Scientific and Technical Information of China (English)

    温登哲; 陈予恕

    2014-01-01

    A fan casing model of cantilever circular thin shell is constructed based on the geometric characteristics of the thin-walled structure of aero-engine fan casing. According to Donnelly’s shell theory and Hamilton’s principle, the dynamic equations are established. The dynamic behaviors are investigated by a multiple-scale method. The effects of casing geometric parameters and motion parameters on the natural frequency of the system are studied. The transition sets and bifurcation diagrams of the system are obtained through a singularity analysis of the bifurcation equation, showing that various modes of the system such as the bifurcation and hysteresis will appear in different parameter regions. In accordance with the multiple relationship of the fan speed and stator vibration frequency, the fan speed interval with the casing vibration sudden jump is calculated. The dynamic reasons of casing cracks are investigated. The possibility of casing cracking hysteresis interval is analyzed. The results show that cracking is more likely to appear in the hysteresis interval. The research of this paper provides a theoretical basis for fan casing design and system parameter optimization.

  12. Fan Noise Source Diagnostic Test: Vane Unsteady Pressure Results

    Science.gov (United States)

    Envia, Edmane

    2002-01-01

    To investigate the nature of fan outlet guide vane pressure fluctuations and their link to rotor-stator interaction noise, time histories of vane fluctuating pressures were digitally acquired as part of the Fan Noise Source Diagnostic Test. Vane unsteady pressures were measured at seven fan tip speeds for both a radial and a swept vane configuration. Using time-domain averaging and spectral analysis, the blade passing frequency (BPF) harmonic and broadband contents of the vane pressures were individually analyzed. Significant Sound Pressure Level (SPL) reductions were observed for the swept vane relative to the radial vane for the BPF harmonics of vane pressure, but vane broadband reductions due to sweep turned out to be much smaller especially on an average basis. Cross-correlation analysis was used to establish the level of spatial coherence of broadband pressures between different locations on the vane and integral length scales of pressure fluctuations were estimated from these correlations. Two main results of this work are: (1) the average broadband level on the vane (in dB) increases linearly with the fan tip speed for both the radial and swept vanes, and (2) the broadband pressure distribution on the vane is nearly homogeneous and its integral length scale is a monotonically decreasing function of fan tip speed.

  13. Numerical Analysis of Erosion Caused by Biomimetic Axial Fan Blade

    Directory of Open Access Journals (Sweden)

    Jun-Qiu Zhang

    2013-01-01

    Full Text Available Damage caused by erosion has been reported in several industries for a wide range of situations. In the present work, a new method is presented to improve the erosion resistance of machine components by biomimetic method. A numerical investigation of solid particle erosion in the standard and biomimetic configuration blade of axial fan is presented. The analysis consists in the application of the discrete phase model, for modeling the solid particles flow, and the Eulerian conservation equations to the continuous phase. The numerical study employs computational fluid dynamics (CFD software, based on a finite volume method. User-defined function was used to define wear equation. Gas/solid flow axial fan was simulated to calculate the erosion rate of the particles on the fan blades and comparatively analyzed the erosive wear of the smooth surface, the groove-shaped, and convex hull-shaped biomimetic surface axial flow fan blade. The results show that the groove-shaped biomimetic blade antierosion ability is better than that of the other two fan blades. Thoroughly analyze of antierosion mechanism of the biomimetic blade from many factors including the flow velocity contours and flow path lines, impact velocity, impact angle, particle trajectories, and the number of collisions.

  14. Topological invariants of a fan associated to a toric variety

    CERN Document Server

    Ford, T J

    1995-01-01

    Associated to a toric variety X of dimension r over a field k is a fan \\Delta on \\Bbb R^r. The fan \\Delta is a finite set of cones which are in one-to-one correspondence with the orbits of the torus action on X. The fan \\Delta inherits the Zariski topology from X. In this article some cohomological invariants of X are studied in terms of whether or not they depend only on \\Delta and not k. Secondly some numerical invariants of X are studied in terms of whether or not they are topological invariants of the fan \\Delta. That is, whether or not they depend only on the finite topological space defined on \\Delta. The invariants with which we are mostly concerned are the class group of Weil divisors, the Picard group, the Brauer group and the dimensions of the torsion free part of the \\'etale cohomology groups with coefficients in the sheaf of units. The notion of an open neighborhood of a fan is introduced and examples are given for which the above invariants are sufficiently fine to give nontrivial stratifications...

  15. "I'm Buffy, and you're history": Putting fan studies into history [editorial

    Directory of Open Access Journals (Sweden)

    Nancy Reagin

    2011-03-01

    Full Text Available This essay kicks off the special historical issue of Transformative Works and Cultures by offering an overview of the ways in which fan communities have been studied by academic historians, and how fan studies has written the history of fan communities. The essay discusses historical work done by amateur fan historians throughout the 20th century; what academic historians can offer fan communities; why academic historians could benefit from studying fandoms as part of the history of popular culture; and what fan studies as a discipline might gain from a broader historical analysis of fandoms.

  16. Atomic physics

    CERN Document Server

    Born, Max

    1989-01-01

    The Nobel Laureate's brilliant exposition of the kinetic theory of gases, elementary particles, the nuclear atom, wave-corpuscles, atomic structure and spectral lines, electron spin and Pauli's principle, quantum statistics, molecular structure and nuclear physics. Over 40 appendices, a bibliography, numerous figures and graphs.

  17. Atomic Calligraphy

    Science.gov (United States)

    Imboden, Matthias; Pardo, Flavio; Bolle, Cristian; Han, Han; Tareen, Ammar; Chang, Jackson; Christopher, Jason; Corman, Benjamin; Bishop, David

    2013-03-01

    Here we present a MEMS based method to fabricate devices with a small number of atoms. In standard semiconductor fabrication, a large amount of material is deposited, after which etching removes what is not wanted. This technique breaks down for structures that approach the single atom limit, as it is inconceivable to etch away all but one atom. What is needed is a bottom up method with single or near single atom precision. We demonstrate a MEMS device that enables nanometer position controlled deposition of gold atoms. A digitally driven plate is swept as a flux of gold atoms passes through an aperture. Appling voltages on four comb capacitors connected to the central plate by tethers enable nanometer lateral precision in the xy plane over 15x15 sq. microns. Typical MEMS structures have manufacturing resolutions on the order of a micron. Using a FIB it is possible to mill apertures as small as 10 nm in diameter. Assuming a low incident atomic flux, as well as an integrated MEMS based shutter with microsecond response time, it becomes possible to deposit single atoms. Due to their small size and low power consumption, such nano-printers can be mounted directly in a cryogenic system at ultrahigh vacuum to deposit clean quench condensed metallic structures.

  18. Effect of Number of Blades on Performance of Ceiling Fans

    Directory of Open Access Journals (Sweden)

    Adeeb Ehsan

    2015-01-01

    Full Text Available In this paper, the effect of number of blades on ceiling fan performance is discussed. This approach helps to satisfy tradeoff between high air flow (performance and power consumption (energy efficiency. Specifically, variation from two to six blades is considered with nonlinear forward sweep profile. Reynolds Averaged Navier-Stokes (RANS technique is used to model the flow field induced by the ceiling fan inside a generic room. The performance is gauged through response parameters namely volumetric flow rate, mass flow rate, torque and energy efficiency. The results indicate that mass and volumetric flow rates are maximized for six blade configuration and energy efficiency is maximized for two blade configuration. The study indicates the importance of tradeoff between high air flow through ceiling fan and associated energy efficiency.

  19. Performance and Stability Analysis of a Shrouded-Fan UAV

    CERN Document Server

    de Divitiis, Nicola

    2009-01-01

    This paper deals with the estimation of the performance and stability for a shrouded-fan unmanned rotorcraft whose mission profile also prescribes the flight in ground effect. The not so simple estimation of the aerodynamic coefficients and of the thrust in the various situations makes the performance calculation and the stability analysis difficult tasks. This is due to the strong interaction between the fan flow and shroud that causes quite different flow structures about the airframe depending on flight conditions. A further difficulty is related to the ground effect which produces substantial modifications in the rotor thrust and aerodynamic coefficients. To evaluate performance and stability, two models have been developed. One determines the aerodynamic coefficients of the shroud, whereas the other one calculates thrust and moment of the rotors system. Both models take into account the mutual interference between fan flow and fuselage and ground effect. Performance and stability are then discussed with ...

  20. Using Mobile Marketing to Engage NASCAR Fans and Increase Sales

    Directory of Open Access Journals (Sweden)

    MARK DODDS

    2011-01-01

    Full Text Available Mobile marketing displays engage the consumer. This sponsorship activation tactic is highly visible at NASCAR races. Some common elements include show cars, interactive race simulators, video games and race suit/equipment displays. The authors of this study argue that by using mobile marketing effectively as a sponsorship activation tactic, the race fans derive more enjoyment from the race experience. This increased enjoyment links to higher product sales for the sponsor. The implications of this study show that sponsors in other sports should use mobile marketing to increase the fan satisfaction of the game experience in order to increase their product sales. Additionally, event mangers should support mobile marketing as a sponsorship activation tactic with the intention of increasing fan enjoyment and improving attendance.

  1. Particle trajectories and acceleration during 3D fan reconnection

    CERN Document Server

    Dalla, S; 10.1051/0004-6361:200809771

    2008-01-01

    Context. The primary energy release in solar flares is almost certainly due to magnetic reconnection, making this a strong candidate as a mechanism for particle acceleration. While particle acceleration in 2D geometries has been widely studied, investigations in 3D are a recent development. Two main classes of reconnection regimes at a 3D magnetic null point have been identified: fan and spine reconnection Aims. Here we investigate particle trajectories and acceleration during reconnection at a 3D null point, using a test particle numerical code, and compare the efficiency of the fan and spine regimes in generating an energetic particle population. Methods. We calculated the time evolution of the energy spectra. We discuss the geometry of particle escape from the two configurations and characterise the trapped and escaped populations. Results. We find that fan reconnection is less efficent than spine reconnection in providing seed particles to the region of strong electric field where acceleration is possible...

  2. Reflection on Chinese boys' love fans: An insider's view [symposium

    Directory of Open Access Journals (Sweden)

    Erika Junhui Yi

    2013-03-01

    Full Text Available The fandom of BL, as it is known in China, celebrates explicit homoerotic relationships between boys or men—fictional characters taken from mainstream media, real-life celebrities, and male personifications of day-to-day objects and animals, as well as original characters. Mainstream media reports on BL fandom and BL fan girls in China have never been favorable; this subculture and the fans within it are constantly represented in a negative and biased light. But because I am a BL fan girl myself, I can offer an insider's perspective. This essay is a reflection on my personal experiences and observations as a member of BL fandom, and a response to erroneous, stigmatizing claims and moral panic about this community in China.

  3. A velocity parameter for the correlation of axial fan noise

    Science.gov (United States)

    Wright, T.

    1982-08-01

    An aerodynamic parameter that relates subsonic axial fan noise to the fundamental flow behavior in the blade row of a fan is proposed. The parameter is the peak or maximum blade surface velocity in the rotating reference frame and includes, either explicitly or implicitly, the influence of tip speed, volume flow rate, pressure rise, shaft horsepower and efficiency. Correlation of the noise associated with a very broad range of axial fans yields good agreement and collapse of data when compared to currently used correlation methods. Use of this parameter, rather than those based on overall performance, allows trade-off studies to be made within a given performance requirement so that a minimum noise configuration may be designed or selected.

  4. Effect of inlet box on performance of axial flow fans

    Institute of Scientific and Technical Information of China (English)

    Jingyin LI; Hua TIAN; Xiaofang YUAN

    2008-01-01

    Numerical investigations on 3D flow fields in an axial flow fan with and without an inlet box have been extensively conducted, focusing on the variation of fan performance caused by the internal flow fields and the velocity evenness at the exit of the inlet box. It is interest-ing to find that although the inlet box is well designed in accordance with basic design principles, there is a flow separation region in it. Furthermore, this flow separation and the resulting uneven velocity distribution at the exit lead to some decrease in the efficiency and an increase in the total pressure rise of the fan. This research shows that the inlet box needs further improvement and such a check on the flow fields is of value for the design of inlet boxes.

  5. Fan filmmaking and copyright in a global world: Warhammer 40,000 fan films and the case of Damnatus

    Directory of Open Access Journals (Sweden)

    John Walliss

    2010-09-01

    Full Text Available The last decade has witnessed a proliferation, both online and off-line, of films produced by amateurs inspired by mainstream films, TV shows, and novels. As with much other fan production, fan films exist in, at best, a legally gray area since they are produced by amateurs, rather than by the media companies that own the copyrights to the films and novels that provide both their inspiration and settings. I examine the phenomenon of fan filmmaking, focusing on films produced by fans of the Warhammer 40,000 (W40K tabletop battle game. In particular, I examine the case of Damnatus: The Enemy Within (Damnatus: Feind Im Innern, 2005, a German-made fan film set in the W40K universe, which was banned from release by the game's rights holder, the UK company Games Workshop, in 2007. Damnatus offers an interesting case study in both the ongoing struggle between rights holders and textual poachers and the tensions that can exist between different legal understandings of copyright in an increasingly globalized world.

  6. The Reasonable Explanation of Annihilation (fanā in Mysticism

    Directory of Open Access Journals (Sweden)

    Abulfazel Kiashemshaki

    2012-06-01

    Full Text Available Abstrak : Para mistikus melampaui tahap-tahap (derajat kesempurnaan mistik dan maqam spiritual dalam perjalanan mereka menuju Allah yang sulit dimengerti oleh non-mistikus. Karena itu, sebagian besar kalangan reflektif berusaha mengandalkan prinsip-prinsip intelektual dan teoritis mereka untuk memperoleh penjelasan atas pengalaman mistis dan ekstasi. Namun, keberhasilan penjelasannya sepenuhnya berada di bawah kuasa dan kekuatan dari prinsip-prinsip tersebut. (Fanā atau kesirnaan adalah salah satu tahap mistis atau keadaan yang sulit dimengerti oleh non-mistikus sehingga memunculkan berbagai teori yang berbeda untuk menjelaskannya. Pencapaian prestasi ilmiah dan filosofis merupakan penjelasan yang tepat atas fanā. Bagaimanapun upaya yang dilakukan dalam artikel ini membuktikan bahwa satu-satunya penjelasan yang sukses adalah penjelasan yang didasarkan pada prinsip-prinsip teosofi transendental dan mistisisme teoritis.Kata kunci : Fanā, Mistisisme, Penjelasan rasional, Mistisisme teoretis, Filsafat transendentalAbstract : Mystics are passing through stages (degrees of mystic perfection and esoteric abodes (spiritual stations in their spiritual journey to Allah which is difficult for unmystics to understand. Because of this, most of the reflective people are trying to rely on their intellectual and theoretical principles to obtain an understandable explanation of mystical experiences and ecstasy. However the success of such explanation completely lies in the power and strength of the above mentioned principles. (Fanā or annihilation is one of the mystical stages or states which unmystics find very difficult to reasonably understand, hence various and different theories have been provided for its explanation. Various scientific and philosophical achievements are appropriate explanations of annihilation (fanā which is valuable in its place; however effort had been made in this article to prove that the only successful explanation is an

  7. The Boundary Layer Interaction with Shock Wave and Expansion Fan

    Institute of Scientific and Technical Information of China (English)

    MaratA.Goldfeld; RomanV.Nestoulia; 等

    2000-01-01

    The results of experimental investigation of a turbulent boundary layer on compression and expansion surfaces are presented.They include the study of the shock wave and /or expansion fan action upon the boundary layer,boundary layer sepqartion and its relaxation.Complex events of paired interactions and the flow on compression convex-concave surfaces were studied.The posibility and conditions of the boundary layer relaminarization behind the expansion fan and its effect on the relaxation length are presented.Different model configurations for wide range conditions were investigated.Comparison of results for different interactions was carried out.

  8. Novel stator design of fan motors using soft magnetic composites

    Science.gov (United States)

    Hsu, Yu-Sheng; Tsai, Mi-Ching; Hsieh, Min-Fu

    2008-04-01

    Cooling fans are an important device needed in consumer electronic products. To enhance the performance of cooling fans, this paper presents a novel brushless dc motor with a three dimensional stator structure using soft magnetic composite to reduce the hub size and allow more airflow. Four models are designed and their output characteristics are compared using finite element simulation. From the results, one of them is selected for prototyping whose performance appears to meet the requirement. The prototype has a 10% smaller diameter than that of conventional types. Moreover, the operation test shows that the required performance is achieved.

  9. On a Fixed Point Theorem of Ky Fan

    Institute of Scientific and Technical Information of China (English)

    DE BLASI Francesco S.; GEORGIEV Pando Gr.

    2002-01-01

    We generalize a theorem of Ky Fan about the nearest distance between a closed convex setD in a Banach space E and its image by a function f: D → E, in several directions: (1) for noncompactsets D, when f(D) precompact; (2) for compact D and upper semicontinuous multifunction f; andmore generally, (3) for noncompact D and upper semicontinuous multifunction f with f(D) Hausdorffprecompact.In particular, we prove a version of the fixed point theorem of Kakutani-Ky Fan for multifunctions,whose values are convex closed bounded, thus not necessarily compact.

  10. Supersonic stall flutter of high-speed fans

    Science.gov (United States)

    Adamczyk, J. J.; Stevans, W.; Jutras, R.

    1981-01-01

    An analytical model is proposed for predicting the onset of supersonic stall bending flutter in high-speed rotors. The analysis is based on a modified two-dimensional, compressible, unsteady actuator disk theory. The stability boundary predicted by the analysis is shown to be in good agreement with the measured boundary of a high speed fan. The prediction that the flutter mode would be a forward traveling wave sensitive to wheel speed and aerodynamic loading is confirmed by experimental measurements. In addition, the analysis shows that reduced frequency and dynamic head also play a significant role in establishing the supersonic stall bending flutter boundary of an unshrouded fan.

  11. The Female Vikings, a women's fan group in Denmark

    DEFF Research Database (Denmark)

    Mintert, Svenja-Maria; Pfister, Gertrud Ursula

    2014-01-01

    Traditionally, football and fandom have been male domains and celebrations of masculinity. So far there has been some sociological and historical research on women's football; however, little is known about women's fandom, in particular about its formation and development. This article focuses...... on the historical development of a Danish women-only fan group called 'The Female Vikings', which support a professional football club, Lyngby Boldklub (BK), in a city north of Copenhagen. The article explores the backgrounds and motivations of female fans, as well as their ways of staging femininity in a man...

  12. The Female Vikings, a women's fan group in Denmark

    DEFF Research Database (Denmark)

    Mintert, Svenja-Maria; Pfister, Gertrud Ursula

    2014-01-01

    Traditionally, football and fandom have been male domains and celebrations of masculinity. So far there has been some sociological and historical research on women's football; however, little is known about women's fandom, in particular about its formation and development. This article focuses......'s world. Drawing on available information about football and fans in Denmark, we have reconstructed the developments of both Lyngby BK and its supporters. Special focus was placed on the histories and cultures as well as the experiences of female fans in this club. Insights into the foundation...

  13. Performance evaluation methods and instrumentation for mine ventilation fans

    Institute of Scientific and Technical Information of China (English)

    LI Man; WANG Xue-rong

    2009-01-01

    Ventilation fans are one of the most important pieces of equipment in coal mines. Their performance plays an important role in the safety of staff and production. Given the actual requirements of coal mine production, we instituted a research project on the measurement methods of key performance parameters such as wind pressure, amount of ventilation and power. At the end a virtual instrument for mine ventilation fans performance evaluation was developed using a USB interface. The practical perform-ance and analytical results of our experiments show that it is feasible, reliable and effective to use the proposed instrumentation for mine ventilation performance evaluation.

  14. "Cultural acupuncture": Fan activism and the Harry Potter Alliance

    Directory of Open Access Journals (Sweden)

    Henry Jenkins

    2012-06-01

    Full Text Available Fan activists have struggled to defend series from cancellation, defend themselves from cease and desist orders, promote alternative representations, and raise money for charity. Building on this background, this article examines how the Harry Potter Alliance encourages young people to speak out as fans on a broad range of human rights and social justice issues through what the group's leader, Andrew Slack, calls "cultural acupuncture." The group's practice of mapping the fictional content world onto real-world concerns helps empower young people to become civicly engaged and politically active.

  15. Towards a three-component model of fan loyalty: a case study of Chinese youth.

    Science.gov (United States)

    Zhang, Xiao-xiao; Liu, Li; Zhao, Xian; Zheng, Jian; Yang, Meng; Zhang, Ji-qi

    2015-01-01

    The term "fan loyalty" refers to the loyalty felt and expressed by a fan towards the object of his/her fanaticism in both everyday and academic discourses. However, much of the literature on fan loyalty has paid little attention to the topic from the perspective of youth pop culture. The present study explored the meaning of fan loyalty in the context of China. Data were collected by the method of in-depth interviews with 16 young Chinese people aged between 19 and 25 years who currently or once were pop fans. The results indicated that fan loyalty entails three components: involvement, satisfaction, and affiliation. These three components regulate the process of fan loyalty development, which can be divided into four stages: inception, upgrade, zenith, and decline. This model provides a conceptual explanation of why and how young Chinese fans are loyal to their favorite stars. The implications of the findings are discussed.

  16. ON A KIND OF GENERALIZED QUASI-VARIATIONAL INEQUALITIES AND FAN's MINIMAX INEQUALITY WITHOUT CONVEXITY

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    This paper gives a Fan,s type minimax theorem, a nearst point theorem and two existence theorems of solutions for a kind of generalized quasi-variational inequalities in H-spaces without any linear structure.

  17. Towards a three-component model of fan loyalty: a case study of Chinese youth.

    Directory of Open Access Journals (Sweden)

    Xiao-xiao Zhang

    Full Text Available The term "fan loyalty" refers to the loyalty felt and expressed by a fan towards the object of his/her fanaticism in both everyday and academic discourses. However, much of the literature on fan loyalty has paid little attention to the topic from the perspective of youth pop culture. The present study explored the meaning of fan loyalty in the context of China. Data were collected by the method of in-depth interviews with 16 young Chinese people aged between 19 and 25 years who currently or once were pop fans. The results indicated that fan loyalty entails three components: involvement, satisfaction, and affiliation. These three components regulate the process of fan loyalty development, which can be divided into four stages: inception, upgrade, zenith, and decline. This model provides a conceptual explanation of why and how young Chinese fans are loyal to their favorite stars. The implications of the findings are discussed.

  18. Experimental investigation of the noise emission of axial fans under distorted inflow conditions

    Science.gov (United States)

    Zenger, Florian J.; Renz, Andreas; Becher, Marcus; Becker, Stefan

    2016-11-01

    An experimental investigation on the noise emission of axial fans under distorted inflow conditions was conducted. Three fans with forward-skewed fan blades and three fans with backward-skewed fan blades and a common operating point were designed with a 2D element blade method. Two approaches were adopted to modify the inflow conditions: first, the inflow turbulence intensity was increased by two different rectangular grids and second, the inflow velocity profile was changed to an asymmetric characteristic by two grids with a distinct bar stacking. An increase in the inflow turbulence intensity affects both tonal and broadband noise, whereas a non-uniform velocity profile at the inlet influences mainly tonal components. The magnitude of this effect is not the same for all fans but is dependent on the blade skew. The impact is greater for the forward-skewed fans than for the backward-skewed and thus directly linked to the fan blade geometry.

  19. Design and Research of Intelligent Remote Control Fan Based on Single Chip Microcomputer and Bluetooth Technology

    National Research Council Canada - National Science Library

    Xue-Xia Zhang; You-Yun Dang; An-Ying Fu

    2017-01-01

    This paper is designed for intelligent remote control fans. The design of the microcontroller as the core, the sensor, Bluetooth and Andrews system applied to the design of intelligent remote control fan...

  20. Process sedimentology of submarine fan deposits - new perspectives

    Science.gov (United States)

    Postma, George

    2017-04-01

    To link submarine fan process sedimentology with sand distribution, sand body architecture, texture and fabric, the field geologist studies sedimentary facies, facies associations (fan elements) and stratigraphy. Facies analysis resides on factual knowledge of modern fan morphodynamics and physical modelling of en-masse sediment transport. Where do we stand after 55 years of submarine research, i.e. the date when the first submarine fan model was launched by Arnold Bouma in 1962? Since that date students of submarine fans have worked on a number of important, recurring questions concerned with facies analysis of submarine successions in outcrop and core: 1. What type of sediment transport produced the beds? 2. What facies can be related to initial flow conditions? 3. What is the significance of grain size jumps and bounding surface hierarchy in beds consisting of crude and spaced stratification (traction carpets)? Do these point to multi flow events or to flow pulsations by one and the same event? 4. What facies associations relate to the basic elements of submarine fans? 5. What are the autogenic and allogenic signatures in submarine fans? Particularly in the last decade, the enormous technical advancement helped to obtain high-quality data from observations of density flows in modern canyons, deep basins and deep-water delta slopes (refs 1,2,3). In combination with both physical (refs 4,5) and numerical modelling (ref 6) these studies broke new ground into our understanding of density flow processes in various submarine environments and have led to new concepts of submarine fan building by super- and subcritical high-density flow (ref 7). Do these new concepts provide better answers to our recurrent questions related to the morphodynamics of submarine fans and prediction of sand body architecture? In discussing this open question, I shall 1. apply the new concepts to a modern and ancient example of a channel-lobe-transition-zone (ref 8); 2. raise the problem of

  1. A Critical Review of Computational Methods and Their Application in Industrial Fan Design

    OpenAIRE

    Alessandro Corsini; Giovanni Delibra; Sheard, Anthony G.

    2013-01-01

    Members of the aerospace fan community have systematically developed computational methods over the last five decades. The complexity of the developed methods and the difficulty associated with their practical application ensured that, although commercial computational codes date back to the 1980s, they were not fully exploited by industrial fan designers until the beginning of the 2000s. The application of commercial codes proved to be problematic as, unlike aerospace fans, industrial fans i...

  2. Debris-flow dominance of alluvial fans masked by runoff reworking and weathering.

    OpenAIRE

    Haas, T.; Ventra, D.; Carbonneau, P. E.; Kleinhans, M. G.

    2014-01-01

    Arid alluvial fan aggradation is highly episodic and fans often comprise active and inactive sectors. Hence the morphology and texture of fan surfaces are partly determined by secondary processes of weathering and erosion in addition to primary processes of aggradation. This introduces considerable uncertainty in the identification of formative processes of terrestrial and Martian fans from aerial and satellite imagery. The objectives of this study are (i) to develop a model to describe the s...

  3. A secondary source configuration for control of a ventilation fan noise in ducts

    OpenAIRE

    Čudina, Mirko; Prezelj, Jurij

    2015-01-01

    The main noise source in heating, ventilation, and air conditioning systems is usually a ventilating fan. Noise, generated by the ventilating fan is transmitted through the duct into the living and working environment. A typical fan noise spectrum consists of a broadband noise, which is superimposed with pure tones. Different methods are available to reduce a transmission of such noise from the ventilating fan into the living and working environment. In this article it is demonstrated how a f...

  4. Kinetic Atom.

    Science.gov (United States)

    Wilson, David B.

    1981-01-01

    Surveys the research of scientists like Joule, Kelvin, Maxwell, Clausius, and Boltzmann as it comments on the basic conceptual issues involved in the development of a more precise kinetic theory and the idea of a kinetic atom. (Author/SK)

  5. Analysis of metal cations and inorganic anions in olive oil mill waste waters by atomic absorption spectroscopy and ion chromatography. Detection of metals bound mainly to the organic polymeric fraction.

    Science.gov (United States)

    Arienzo, M; Capasso, R

    2000-04-01

    Metal cations were quantitatively detected by atomic absorption spectrometry in samples of olive oil mill waste waters obtained by a pressure process (omww(1)) (K, 17.1; Mg, 2.72; Ca, 2.24; Na, 0.40; Fe, 0.123; Zn, 0.0630; Mn, 0.0147; Cu, 0.00860 g L(-)(1)) and a centrifugation process (omww(2)) (K, 9.80; Mg, 1.65; Ca, 1.35; Na, 0. 162; Fe, 0.0330; Zn, 0.0301; Mn, 0.00910; Cu, 0.00980 g L(-)(1)). The inorganic anions, determined in the same samples by ion chromatography, proved to be Cl(-), H(2)PO(4)(-), F(-), SO(4)(2)(-), and NO(3)(-) (1.61, 1.05, 0.66, 0.52, and 0.023 g L(-)(1), respectively, in omww(1) and 0.61, 0.40, 0.25, 0.20, and 0.0090 g L(-)(1), respectively, in omww(2)). Most of the metal cations were revealed to be bound to the omww organic polymeric fraction (opf), composed of polysaccharides, phenol polymers, and proteins. Opf relative molecular weight was substantially estimated in the range between 1000 and 30000 Da for approximately 75% and in the range from 30000 to 100000 Da for approximately 25%. The free residual cations pool proved to be neutralized by the inorganic counteranions. Finally, the possible exploitation of this material in agriculture and in environmental biotechnology processes is also discussed in the light of its chemical and biochemical oxygen demand parameters.

  6. Surface morphology of fans in the high-Arctic periglacial environment of Svalbard : Controls and processes

    NARCIS (Netherlands)

    De Haas, Tjalling; Kleinhans, Maarten G.; Carbonneau, Patrice E.; Rubensdotter, Lena; Hauber, Ernst

    2015-01-01

    Fan-shaped landforms occur in all climatic regions on Earth. They have been extensively studied in many of these regions, but there are few studies on fans in periglacial, Arctic and Antarctic regions. Fans in such regions are exposed to many site-specific environmental conditions in addition to the

  7. 30 CFR 75.313 - Main mine fan stoppage with persons underground.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Main mine fan stoppage with persons underground... COAL MINE SAFETY AND HEALTH MANDATORY SAFETY STANDARDS-UNDERGROUND COAL MINES Ventilation § 75.313 Main mine fan stoppage with persons underground. (a) If a main mine fan stops while anyone is underground...

  8. Debris-flow dominance of alluvial fans masked by runoff reworking and weathering

    NARCIS (Netherlands)

    de Haas, Tjalling; Ventra, Dario; Carbonneau, Patrice E.; Kleinhans, Maarten G.

    2014-01-01

    Arid alluvial fan aggradation is highly episodic and fans often comprise active and inactive sectors. Hence the morphology and texture of fan surfaces are partly determined by secondary processes of weathering and erosion in addition to primary processes of aggradation. This introduces considerable

  9. Determination of five kinds of trace elements in hogwash oil by microwave digestion-atomic absorption spectrometry%微波消解-原子吸收光谱法测定地沟油中5种微量元素

    Institute of Scientific and Technical Information of China (English)

    陈少永; 陶兆林; 张翊; 薛洪宝

    2015-01-01

    Objective:To explore the differences of five kinds of trace elements between edible cooking oil and hogwash oil. Methods:Different kinds of 5 parts edible oil and 1 part homemade lard oil,3 parts old cooking oil and 3 parts hogwash oil were collected. In each sample,0. 3 ~ 0. 4 g was weighed accurately. The samples were digested into a solution for determination by microwave. The contents of copper( Cu) ,zinc( Zn) ,manganese( Mn) ,lead( Pb) and iron( Fe) were determined by atomic absorption spectrometry. Results:In the experimental concentration range,the recovery rate was between 97. 6% to 102. 4%,the relative average deviation was 0. 6% to 2. 5%. The contents of 5 kinds of trace elements in old cooking oil were similar to soybean oil,and there had no differences of Cu,Zn,Mn and Pb contents between the edible oil and hogwash oil,whereas Fe content in old cooking oil and hogwash oil was higher than that in the edible oil(P<0. 01). Conclusions:There had no statistical differences of elements Cu,Zn,Mn and Pb contents between the edible oil and hogwash oil. Fe content was increased in hogwash oil,which may be due to the long-term exposure to the iron products when the hogwash oil was refined and transported.%目的::探讨地沟油与食用油中5种微量元素之间的差别。方法:选取不同种类的食用油5份和自制猪油1份(均称食用油),收集地沟油和煎炸老油各3份,准确称取各样品0.3~0.4 g,采用微波消解法制成可供测定的溶液,用原子吸收光谱法测定铜(Cu)、锌(Zn)、锰(Mn)、铅(Pb)和铁(Fe)的含量。结果:在实验选定浓度范围内,5种微量元素回收率为97.6%~102.4%,相对标准偏差为0.6%~2.5%。煎炸老油中5种微量元素的含量和大豆油相近;6种食用油中Cu、Zn、Mn和Pb的含量与地沟油差别不大;地沟油和煎炸老油中Fe的含量比6种食用油高(P<0.01)。结论:地沟油中Cu、Zn、Mn、Pb元素含量与食用油的含量差别不大,而Fe元素含

  10. Palaeoflow reconstruction from fan delta morphology on Mars

    NARCIS (Netherlands)

    Kleinhans, M.G.; Kasteele, H.E. van de; Hauber, E.

    2010-01-01

    Alluvial fans and deltas on Mars record past hydrological conditions. Until now these conditions have been inferred from the morphology of the feeder channels and the deposits from images and digital terrain models (DTMs), and from calculations of the bulk fluxes of water and sediment based on the d

  11. KKM and KY fan theorems in modular function spaces

    Directory of Open Access Journals (Sweden)

    Latif Abdul

    2011-01-01

    Full Text Available Abstract In modular function spaces, we introduce Knaster-Kuratowski-Mazurkiewicz mappings (in short KKM-mappings and prove an analogue to Ky Fan s fixed point theorem. 2010 Mathematics Subject Classification: Primary 46B20, 47H09; Secondary 47H10.

  12. The Nonrelativistic Scattering States of the Deng-Fan Potential

    Directory of Open Access Journals (Sweden)

    Bentol Hoda Yazarloo

    2013-01-01

    Full Text Available The approximately analytical scattering state solution of the Schrodinger equation is obtained for the Deng-Fan potential by using an approximation scheme to the centrifugal term. Energy eigenvalues, normalized wave functions, and scattering phase shifts are calculated. We consider and verify two special cases: the l=0 and the s-wave Hulthén potential.

  13. Modeling Fan Effects on the Time Course of Associative Recognition

    Science.gov (United States)

    Schneider, Darryl W.; Anderson, John R.

    2012-01-01

    We investigated the time course of associative recognition using the response signal procedure, whereby a stimulus is presented and followed after a variable lag by a signal indicating that an immediate response is required. More specifically, we examined the effects of associative fan (the number of associations that an item has with other items…

  14. Investigation of Cross Flow Fan Propulsion for Lightweight VTOL Aircraft

    Science.gov (United States)

    2000-12-01

    the aircraft longitudinal axis due to the total length of the unit. A total fan span of 20.6 inches is required to produce 690 lbf of thrust when...which are mounted parallel to the aircraft longitudinal axis and rest perpendicular, would be actuated as required to provide yaw control and aft

  15. Studying a Spacecraft Ventilation Fan: Progress and Possibilities

    Science.gov (United States)

    Koch, L. Denielle

    2011-01-01

    This document describes a presentation delivered to the Acoustics Technical Working Group at a meeting held in Cleveland, Ohio on April 21-22, 2011. The information contained in this presentation is considered to be preliminary, intended to begin a general discussion among audience members on the challenges associated with spacecraft ventilation fans and possible avenues of continued research.

  16. Propellers And Fans Based On The Moebius Strip

    Science.gov (United States)

    Seiner, John Milton; Gilinsky, Mikhail Markovich

    1996-01-01

    Moebius strip proposed as basis for optimally shaped airplane and boat propellers, fans, helicopter rotors, mixing screws, coffee grinders, and concrete mixers. Basic idea of optimal shaping of such device to increase working efficiency by increasing area for capture of still medium without increasing power needed for rotation.

  17. Intermittent Flow Regimes in a Transonic Fan Airfoil Cascade

    Directory of Open Access Journals (Sweden)

    J. Lepicovsky

    2004-01-01

    velocity.To date, this flow behavior has only been observed in a linear transonic cascade. Further research is necessary to confirm this phenomenon occurs in actual transonic fans and is not the by-product of an endwall restricted linear cascade.

  18. Energy efficient engine shroudless, hollow fan blade technology report

    Science.gov (United States)

    Michael, C. J.

    1981-01-01

    The Shroudless, Hollow Fan Blade Technology program was structured to support the design, fabrication, and subsequent evaluation of advanced hollow and shroudless blades for the Energy Efficient Engine fan component. Rockwell International was initially selected to produce hollow airfoil specimens employing the superplastic forming/diffusion bonding (SPF/DB) fabrication technique. Rockwell demonstrated that a titanium hollow structure could be fabricated utilizing SPF/DB manufacturing methods. However, some problems such as sharp internal cavity radii and unsatisfactory secondary bonding of the edge and root details prevented production of the required quantity of fatigue test specimens. Subsequently, TRW was selected to (1) produce hollow airfoil test specimens utilizing a laminate-core/hot isostatic press/diffusion bond approach, and (2) manufacture full-size hollow prototype fan blades utilizing the technology that evolved from the specimen fabrication effort. TRW established elements of blade design and defined laminate-core/hot isostatic press/diffusion bonding fabrication techniques to produce test specimens. This fabrication technology was utilized to produce full size hollow fan blades in which the HIP'ed parts were cambered/twisted/isothermally forged, finish machined, and delivered to Pratt & Whitney Aircraft and NASA for further evaluation.

  19. SOME GENERALIZATIONS OF KY FAN'S BEST APPROXIMATION THEOREM

    Institute of Scientific and Technical Information of China (English)

    A.R.Khan; N.Hussain; A.B.Thaheem

    2004-01-01

    We pressent new Ky Fan type best approximation theorems for a discontinuous multivalued map on metrizable topological vector spaces and hyperconvex spaces. In addition, fixed point results are derived for the map studied. Our work generalizes severl results in approximation theory.

  20. Così fan tutte: Brilliance or Buffoonery?

    Directory of Open Access Journals (Sweden)

    Sarah Whitfield

    2011-12-01

    Full Text Available Hardly any opera has endured more scrutiny and self-preserving apology than Mozart’s Così fan tutte. Flagrant opposition and a long string of “rescue” attempts shroud the receptive history of the work. Since its premiere, Così fan tutte has long been recognized as a problem opera. Many critics found it implausible that Mozart—the consummate composer and man that warranted their idolization—could have stooped so low as to agree to such an immoral plot. The great beauty in Mozart’s musical parody is that it at once mocks and transforms the supposed superficial experiment of Lorenzo Da Ponte’s libretto. The parody in Così fan tutte must be correctly interpreted. It is rampant, but it exists for much more than a perfunctory laugh. The beauty of Mozart’s music—in both moments of wild parody and heartfelt emotion—succeeds in giving Così fan tutte a depth that is both challenging and transforming.

  1. Analysis and control of computer cooling fan noise

    Science.gov (United States)

    Wong, Kam

    This thesis is divided into three parts: the study of the source mechanisms and their separation, passive noise control, and active noise control. The mechanisms of noise radiated by a typical computer cooling fan is investigated both theoretically and experimentally focusing on the dominant rotor-stator interaction. The unsteady force generated by the aerodynamic interaction between the rotor blades and struts is phase locked with the blade rotation and radiates tonal noise. Experimentally, synchronous averaging with the rotation signal extracts the tones made by the deterministic part of the rotor-strut interaction mechanism. This averaged signal is called the rotary noise. The difference between the overall noise and rotary noise is defined as random noise which is broadband in the spectrum. The deterministic tonal peaks are certainly more annoying than the broadband, so the suppression of the tones is the focus of this study. Based on the theoretical study of point force formulation, methods are devised to separate the noise radiated by the two components of drag and thrust forces on blades and struts. The source separation is also extended to the leading and higher order modes of the spinning pressure pattern. By using the original fan rotor and installing it in various casings, the noise sources of the original fan are decomposed into elementary sources through directivity measurements. Details of the acoustical directivity for the original fan and its various modifications are interpreted. For the sample fan, two common features account for most of the tonal noise radiated. The two features are the inlet flow distortion caused by the square fan casing, and the large strut carrying the electric wires for the motor. When the inlet bellmouth is installed and the large strut is trimmed down to size, a significant reduction of 12 dB in tonal sound power is achieved. These structural corrections constitute the passive noise control. However, the end product still

  2. First Test of Fan Active Noise Control (ANC) Completed

    Science.gov (United States)

    2005-01-01

    With the advent of ultrahigh-bypass engines, the space available for passive acoustic treatment is becoming more limited, whereas noise regulations are becoming more stringent. Active noise control (ANC) holds promise as a solution to this problem. It uses secondary (added) noise sources to reduce or eliminate the offending noise radiation. The first active noise control test on the low-speed fan test bed was a General Electric Company system designed to control either the exhaust or inlet fan tone. This system consists of a "ring source," an induct array of error microphones, and a control computer. Fan tone noise propagates in a duct in the form of spinning waves. These waves are detected by the microphone array, and the computer identifies their spinning structure. The computer then controls the "ring source" to generate waves that have the same spinning structure and amplitude, but 180 out of phase with the fan noise. This computer generated tone cancels the fan tone before it radiates from the duct and is heard in the far field. The "ring source" used in these tests is a cylindrical array of 16 flat-plate acoustic radiators that are driven by thin piezoceramic sheets bonded to their back surfaces. The resulting source can produce spinning waves up to mode 7 at levels high enough to cancel the fan tone. The control software is flexible enough to work on spinning mode orders from -6 to 6. In this test, the fan was configured to produce a tone of order 6. The complete modal (spinning and radial) structure of the tones was measured with two builtin sets of rotating microphone rakes. These rakes provide a measurement of the system performance independent from the control system error microphones. In addition, the far-field noise was measured with a semicircular array of 28 microphones. This test represents the first in a series of tests that demonstrate different active noise control concepts, each on a progressively more complicated modal structure. The tests are

  3. Peanut Oil

    Science.gov (United States)

    ... and baby care products. Sometimes the less expensive soya oil is added to peanut oil. ... are pregnant or breast-feeding. Allergy to peanuts, soybeans, and related plants: Peanut oil can cause serious ...

  4. Oil Spills

    Science.gov (United States)

    Oil spills often happen because of accidents, when people make mistakes or equipment breaks down. Other causes include natural disasters or deliberate acts. Oil spills have major environmental and economic effects. Oil ...

  5. Experimental Evaluation of Installed Cooking Exhaust Fan Performance

    Energy Technology Data Exchange (ETDEWEB)

    Singer, Brett C.; Delp, William W.; Apte, Michael G.

    2010-11-01

    The installed performance of cooking exhaust fans was evaluated through residential field experiments conducted on a sample of 15 devices varying in design and other characteristics. The sample included two rear downdraft systems, two under-cabinet microwave over range (MOR) units, three different installations of an under-cabinet model with grease screens across the bottom and no capture hood, two devices with grease screens covering the bottom of a large capture hood (one under-cabinet, one wall-mount chimney), four under-cabinet open hoods, and two open hoods with chimney mounts over islands. Performance assessment included measurement of airflow and sound levels across fan settings and experiments to quantify the contemporaneous capture efficiency for the exhaust generated by natural gas cooking burners.Capture efficiency is defined as the fraction of generated pollutants that are removed through the exhaust and thus not available for inhalation of household occupants. Capture efficiency (CE) was assessed for various configurations of burner use (e.g., single front, single back, combination of one front and one back, oven) and fan speed setting. Measured airflow rates were substantially lower than the levels noted in product literature for many of the units. This shortfall was observed for several units costing in excess of $1000. Capture efficiency varied widely (from<5percent to roughly 100percent) across devices and across conditions for some devices. As expected, higher capture efficiencies were achieved with higher fan settings and the associated higher air flow rates. In most cases, capture efficiencies were substantially higher for rear burners than for front burners. The best and most consistent performance was observed for open hoods that covered all cooktop burners and operated at higher airflow rates. The lowest capture efficiencies were measured when a front burner was used with a rear backdraft system or with lowest fan setting for above the range

  6. Design of a Low Speed Fan Stage for Noise Suppression

    Science.gov (United States)

    Dalton, W. N.; Elliot, D. B.; Nickols, K. L.

    1999-01-01

    This report describes the design of a low tip speed, moderate pressure rise fan stage for demonstration of noise reduction concepts. The fan rotor is a fixed-pitch configuration delivering a design pressure ratio of 1.378 at a specific flow of 43.1 lbm/sec/sq ft. Four exit stator configurations were provided to demonstrate the effectiveness of circumferential and axial sweep in reducing rotor-stator interaction tone noise. The fan stage design was combined with an axisymmetric inlet, conical convergent nozzle, and nacelle to form a powered fan-nacelle subscale model. This model has a 22-inch cylindrical flow path and employs a rotor with a 0.30 hub-to-tip radius ratio. The design is fully compatible with an existing NASA force balance and rig drive system. The stage aerodynamic and structural design is described in detail. Three-dimensional (3-D) computational fluid dynamics (CFD) tools were used to define optimum airfoil sections for both the rotor and stators. A fan noise predictive system developed by Pratt & Whitney under contract to NASA was used to determine the acoustic characteristics of the various stator configurations. Parameters varied included rotor-to-stator spacing and vane leading edge sweep. The structural analysis of the rotor and stator are described herein. An integral blade and disk configuration was selected for the rotor. Analysis confirmed adequate low cycle fatigue life, vibratory endurance strength, and aeroelastic suitability. A unique load carrying stator arrangement was selected to minimize generation of tonal noise due to sources other than rotor-stator interaction. Analysis of all static structural components demonstrated adequate strength, fatigue life, and vibratory characteristics.

  7. Upgrading of petroleum oil feedstocks using alkali metals and hydrocarbons

    Energy Technology Data Exchange (ETDEWEB)

    Gordon, John Howard

    2014-09-09

    A method of upgrading an oil feedstock by removing heteroatoms and/or one or more heavy metals from the oil feedstock composition. This method reacts the oil feedstock with an alkali metal and an upgradant hydrocarbon. The alkali metal reacts with a portion of the heteroatoms and/or one or more heavy metals to form an inorganic phase separable from the organic oil feedstock material. The upgradant hydrocarbon bonds to the oil feedstock material and increases the number of carbon atoms in the product. This increase in the number of carbon atoms of the product increases the energy value of the resulting oil feedstock.

  8. Upgrading of petroleum oil feedstocks using alkali metals and hydrocarbons

    Science.gov (United States)

    Gordon, John Howard

    2014-09-09

    A method of upgrading an oil feedstock by removing heteroatoms and/or one or more heavy metals from the oil feedstock composition. This method reacts the oil feedstock with an alkali metal and an upgradant hydrocarbon. The alkali metal reacts with a portion of the heteroatoms and/or one or more heavy metals to form an inorganic phase separable from the organic oil feedstock material. The upgradant hydrocarbon bonds to the oil feedstock material and increases the number of carbon atoms in the product. This increase in the number of carbon atoms of the product increases the energy value of the resulting oil feedstock.

  9. Electrostatic atomization: Effect of electrode materials on electrostatic atomizer performance

    Science.gov (United States)

    Sankaran, Abhilash; Staszel, Christopher; Kashir, Babak; Perri, Anthony; Mashayek, Farzad; Yarin, Alexander

    2016-11-01

    Electrostatic atomization was studied experimentally with a pointed electrode in a converging nozzle. Experiments were carried out on poorly conductive canola oil where it was observed that electrode material may affect charge transfer. This points at the possible faradaic reactions that can occur at the surfaces of the electrodes. The supply voltage is applied to the sharp electrode and the grounded nozzle body constitutes the counter-electrode. The charge transfer is controlled by the electrochemical reactions on both the electrodes. The electrical performance study of the atomizer issuing a charged oil jet was conducted using three different nozzle body materials - brass, copper and stainless steel. Also, two sharp electrode materials - brass and stainless steel - were tested. The experimental results revealed that both the nozzle body material, as well as the sharp electrode material affected the spray and leak currents. Moreover, the effect of the sharp electrode material is quite significant. This research is supported by NSF Grant 1505276.

  10. Fans and their applications in General Topology, Functional Analysis and Topological Algebra

    OpenAIRE

    Banakh, Taras

    2016-01-01

    A family of closed subsets of a topological space $X$ is called a (strict) $Cld$-fan in $X$ if this family is (strictly) compact-finite but not locally finite in $X$. Applications of (strict) $Cld$-fans are based on a simple observation that $k$-spaces contain no $Cld$-fan and Ascoli spaces contain no strict $Cld$-fan. In this paper we develop the machinery of (strict) fans and apply it to detecting the $k$-space and Ascoli properties in spaces that naturally appear in General Topology, Funct...

  11. Numerical investigation of geometric parameter effects on the aerodynamic performance of a Bladeless fan

    OpenAIRE

    Mohammad Jafari; Hossein Afshin; Bijan Farhanieh; Atta Sojoudi

    2016-01-01

    Aerodynamic performance of a Bladeless fan is numerically investigated considering the effect of five geometric parameters. Airflow through this fan was analyzed by simulating a Bladeless fan within a 2 m × 2 m × 4 m room. Analysis of the flow field inside the fan and the evaluation of its performance were obtained by solving conservations of mass and momentum equations for the aerodynamic investigations. In order to design the Bladeless fan an Eppler 473 airfoil profile was used as the cross...

  12. Reverse Flow Engine Core Having a Ducted Fan with Integrated Secondary Flow Blades

    Science.gov (United States)

    Kisska, Michael K. (Inventor); Princen, Norman H. (Inventor); Kuehn, Mark S. (Inventor); Cosentino, Gary B. (Inventor)

    2014-01-01

    Secondary air flow is provided for a ducted fan having a reverse flow turbine engine core driving a fan blisk. The fan blisk incorporates a set of thrust fan blades extending from an outer hub and a set of integral secondary flow blades extending intermediate an inner hub and the outer hub. A nacelle provides an outer flow duct for the thrust fan blades and a secondary flow duct carries flow from the integral secondary flow blades as cooling air for components of the reverse flow turbine engine.

  13. On the design and structural analysis of jet engine fan blade structures

    Science.gov (United States)

    Amoo, Leye M.

    2013-07-01

    Progress in the design and structural analysis of commercial jet engine fan blades is reviewed and presented. This article is motivated by the key role fan blades play in the performance of advanced gas turbine jet engines. The fundamentals of the associated physics are emphasized. Recent developments and advancements have led to an increase and improvement in fan blade structural durability, stability and reliability. This article is intended as a high level review of the fan blade environment and current state of structural design to aid further research in developing new and innovative fan blade technologies.

  14. Gas Turbine Engine Having Fan Rotor Driven by Turbine Exhaust and with a Bypass

    Science.gov (United States)

    Suciu, Gabriel L. (Inventor); Chandler, Jesse M. (Inventor)

    2016-01-01

    A gas turbine engine has a core engine incorporating a core engine turbine. A fan rotor is driven by a fan rotor turbine. The fan rotor turbine is in the path of gases downstream from the core engine turbine. A bypass door is moveable from a closed position at which the gases from the core engine turbine pass over the fan rotor turbine, and moveable to a bypass position at which the gases are directed away from the fan rotor turbine. An aircraft is also disclosed.

  15. On-chip grating coupler array on the SOI platform for fan-in/fan-out of MCFs with low insertion loss and crosstalk

    DEFF Research Database (Denmark)

    Ding, Yunhong; Ye, Feihong; Peucheret, Christophe

    2015-01-01

    We report the design and fabrication of a compact multi-core fiber fan-in/fan-out using a grating coupler array on the SOI platform. The grating couplers are fully-etched, enabling the whole circuit to be fabricated in a single lithography and etching step. Thanks to the apodized design for the g......We report the design and fabrication of a compact multi-core fiber fan-in/fan-out using a grating coupler array on the SOI platform. The grating couplers are fully-etched, enabling the whole circuit to be fabricated in a single lithography and etching step. Thanks to the apodized design...

  16. Aeroelastic Calculations of Quiet High- Speed Fan Performed

    Science.gov (United States)

    Bakhle, Milind A.; Srivastava, Rakesh; Mehmed, Oral; Min, James B.

    2002-01-01

    An advanced high-speed fan was recently designed under a cooperative effort between the NASA Glenn Research Center and Honeywell Engines & Systems. The principal design goals were to improve performance and to reduce fan noise at takeoff. Scale models of the Quiet High-Speed Fan were tested for operability, performance, and acoustics. During testing, the fan showed significantly improved noise characteristics, but a self-excited aeroelastic vibration known as flutter was encountered in the operating range. Flutter calculations were carried out for the Quiet High-Speed Fan using a three-dimensional, unsteady aerodynamic, Reynolds-averaged Navier-Stokes turbomachinery code named "TURBO." The TURBO code can accurately model the viscous flow effects that can play an important role in various aeroelastic problems such as flutter with flow separation, flutter at high loading conditions near the stall line (stall flutter), and flutter in the presence of shock and boundary-layer interaction. Initially, calculations were performed with no blade vibrations. These calculations were at a constant rotational speed and a varying mass flow rate. The mass flow rate was varied by changing the backpressure at the exit boundary of the computational domain. These initial steady calculations were followed by aeroelastic calculations in which the blades were prescribed to vibrate harmonically in a natural mode, at a natural frequency, and with a fixed interblade phase angle between adjacent blades. The AE-prep preprocessor was used to interpolate the in-vacuum mode shapes from the structural dynamics mesh onto the computational fluid dynamics mesh and to smoothly propagate the grid deformations from the blade surface to the interior points of the grid. The aeroelastic calculations provided the unsteady aerodynamic forces on the blade surface due to blade vibrations. These forces were vector multiplied with the structural dynamic mode shape to calculate the work done on the blade during

  17. Atomic theories

    CERN Document Server

    Loring, FH

    2014-01-01

    Summarising the most novel facts and theories which were coming into prominence at the time, particularly those which had not yet been incorporated into standard textbooks, this important work was first published in 1921. The subjects treated cover a wide range of research that was being conducted into the atom, and include Quantum Theory, the Bohr Theory, the Sommerfield extension of Bohr's work, the Octet Theory and Isotopes, as well as Ionisation Potentials and Solar Phenomena. Because much of the material of Atomic Theories lies on the boundary between experimentally verified fact and spec

  18. Quantitative analysis of the geometry of submarine channels: Implications for the classification of submarine fans

    Science.gov (United States)

    Clark, J. D.; Kenyon, N. H.; Pickering, K. T.

    1992-07-01

    Certain attributes of submarine channels measured from GLORIA sidescan sonar data from 16 different submarine fans indicate similarities with fluviatile systems. Channel width, depth, meander radius and wavelength, sinuosity, and gradient were measured. This approach makes it possible to identify high- sinuosity, low-gradient (e.g., Indus Fan channels) and low-sinuosity, high- gradient (e.g., Porcupine Seabight channels) channel systems as end members. Current classifications of submarine fans relate fan shape to grain size or sediment caliber and therefore are inadequate, principally because the shape of the fan is strongly controlled by the shape of the receiving basin, which in turn is dependent upon parameters such as tectonics and diapirism. Overall fan shape is almost invariably independent of the physics of sediment transport. Rather than fan shape, the geometry and other characteristics of submarine channels and canyons provide a more promising means of differentiating deep- marine turbidite systems.

  19. Submarine-fan facies associations of the Upper Cretaceous and Paleocene Gottero Sandstone, Ligurian Apennines, Italy

    Science.gov (United States)

    Nilsen, Tor H.; Abbate, Ernesto

    1984-06-01

    The Upper Cretaceous and Paleocene Gottero Sandstone was deposited as a small deep-sea fan on ophiolitic crust in a trench-slope basin. It was thrust northeastward as an allochthonous sheet in Early and Middle Cenozoic time. The Gottero, as thick as 1500 m, was probably derived from erosion of Hercynian granites and associated metamorphic rocks in northern Corsica. Outcrops of inner-fan channel, middle-fan channel and interchannel, outer-fan lobe, fan-fringe, and basin-plain facies associations indicate that the depositional model of Mutti and Ricci Lucchi for mixed-sediment deep-sea fans can be used. The original fan had a radius of 30 to 50 km.

  20. Human KIAA1018/FAN1 nuclease is a new mitotic substrate of APC/CCdh1

    Institute of Scientific and Technical Information of China (English)

    Fenju Lai; Kaishun Hu; Yuanzhong Wu; Jianjun Tang; Yi Sang; Jingying Cao; Tiebang Kang

    2012-01-01

    A recently identified protein,FAN1 (FANCD2-associated nuclease 1,previously known as KIAA1018),is a novel nuclease associated with monoubiquitinated FANCD2 that is required for cellular resistance against DNA interstrand crosslinking (ICL) agents.The mechanisms of FAN1 regulation have not yet been explored.Here,we provide evidence that FAN1 is degraded during mitotic exit,suggesting that FAN1 may be a mitotic substrate of the anaphase-promoting cyclosome complex (APC/C).Indeed,.Cdh1,but not Cdc20,was capable of regulating the protein level of FAN1 through the KEN box and the D-box.Moreover,the up- and down-regulation of FAN1 affected the progression to mitotic exit.Collectively,these data suggest that FAN1 may be a new mitotic substrate of APC/CCdh1 that plays a key role during mitotic e xit.

  1. Modal analysis of an aircraft engine fan noise

    Science.gov (United States)

    Gorodkova, Natalia; Chursin, Valeriy; Bersenev, Yuliy; Burdakov, Ruslan; Siner, Aleksandr; Viskova, Tatiana

    2016-10-01

    The fan is one of the main noise sources of an aircraft engine. To reduce fan noise and provide liner optimization in the inlet it is necessary to research modal structure of the fan noise. The present paper contains results of acoustic tests on installation for mode generation that consists of 34-channel generator and the inlet updated for mounting of 100 microphones, the experiments were provided in new anechoic chamber of Perm National Research Polytechnic University, the engine with the same inlet was also tested in the open test bench conditions, and results of the fan noise modal structure are presented. For modal structure educting, all 100 channels were synchronously registered in a given frequency range. The measured data were analyzed with PULSE analyzer using fast Fourier transform with a frequency resolution 8..16 Hz. Single modes with numbers from 0 to 35 at frequencies 500; 630; 800; 1000; 1250; 1600 Hz and different combinations of modes at frequencies 1000, 1600, 2000, 2500 Hz were set during tests. Modes with small enough numbers are generated well on the laboratory installation, high-number modes generate additional modes caused by a complicated interference pattern of sound field in the inlet. Open test bench results showed that there are also a lot of harmonic components at frequencies lower than fan BPF. Under 0.65 of cut off there is only one distinct mode, other modes with close and less numbers appear from 0.7 of cut off and above. At power regimes 0.76 and 0.94 of cut off the highest mode also changes from positive to negative mode number area. Numbers of the highest modes change smoothly enough with the growth of power regime. At power regimes with Mach>1 (0.7 of cut off and above) on circumference of blade wheel there is a well-defined noise of shock waves at rotor frequency harmonics that appears at the range between the first rotor frequency and fan blade passing frequency (BPF). It is planned to continue researching of sound field

  2. Analysis of Axial Flow Ventilation Fans by Vortex - Method.

    Science.gov (United States)

    Hardin, Richard Anthony

    A steady vortex-lattice method is used to solve the lifting surface equation for an axial flow fan. The type of fan studied is designed for industrial and ventilation applications and in thermofluid systems such as cooling towers. The fan blades are thin cambered surfaces manufactured from metal sheets. The numerical approach is inviscid and results in a boundary value problem with viscous effects partially accounted for by application of drag coefficient data. A non-linear wake alignment procedure is used to account for the effects of vorticity shedding in the wake and variation in wake geometry with operating conditions. The wake alignment procedure is semi-free with wake input parameters required for accurate use of the technique. A study of the wake parameters was conducted and gave trends in the variation of their values with flow rate. At "free-air" conditions, flow visualization estimates of these parameters were found to agree with those from the computations. Comparisons are made between the measured and predicted fan performance with and without a surrounding duct. The comparison of the results were especially good at the "free-air" condition using wake parameters determined from flow visualization and an inlet velocity profile measured using hot-wire anemometry. To enable better understanding of basic flow phenomena and to provide data for verification of numerical analyses, a method for measuring unsteady surface pressure on a rotating axial-flow fan blade was devised. Unsteadiness of pressure on the blade surfaces is due to the effects of upstream fan motor supports and other installation features. A pressure transducer and signal amplification circuit were mounted on a circuit board at the rotating hub with signals taken off the rotating shaft through copper disk-mercury slip rings. The pressure difference across the blade was determined and the data were corrected for time lag and distortion caused by the length of tubing. The pressure difference

  3. 电感耦合等离子体发射光谱法测定油田水中的硼%Determination of Boron in Oil Field Water by Inductively Coupled Plasma-Atomic Emission Spectrometry

    Institute of Scientific and Technical Information of China (English)

    宋继芳

    2012-01-01

    样品经硝酸酸化、滤膜过滤处理后,用电感耦合等离子体发射光谱法直接测定其中硼的含量.通过正交实验优选仪器参数和分析谱线,在选定的波长208.959nm下,对样品稀释倍数和介质酸种类进行选择,结果表明,硼含量低于10mg/L的样品不用稀释,高于10mg/L的样品一般稀释20倍,介质选用硝酸可使测定结果更加准确.对油田水中共存的7种主要金属元素进行了干扰试验,样品中存在20mg/L的Sr、Ba、Fe,50mg/L的Mg、Ca,100mg/L的K,200mg/L的Na对待测元素的测定没有影响.选取油田水样品进行加标回收试验,方法平均回收率为95.3%~102.0%,精密度(RSD,n=11)为0.43%~0.92%,检出限为0.0020mg/L.方法简便、快速,结果令人满意,与姜黄素分光光度法比较,克服了分析流程长、使用试剂较多且不易操作的不足.%Boron in oil field water has been directly determined by Inductively Coupled Plasma-Atomic Emission Spectrometry (ICP-AES) after sample were treated with nitric acid and filtrated. This method overcomes the problems of spectrophotometry such as long analysis flow, more reagent and difficulty in controlling the chemical procedure. The working parameters and the spectral line were optimized by orthogonal tests. The dilute multiple and acid medium were analyzed using the selected 208.959 nm frequency. The results show that it is not necessary to dilute the sample when the content of B is less than 10 mg/L, and the dilution factor is 20 when B is greater than 10 mg/L. The selected HNO3 as the acid medium, improved the accuracy of the results. The interference tests were carried out for 7 major metals in oil field water. 20 mg/L Sr, Ba and Fe, 50 mg/L Mg and Ca, 100 mg/L K and 200 mg/L Na have no interference for the measurements of the target element. The detection limit of boron was 0.0020 mg/L and the recoveries ranged from 95.3% to 102.0% with a precision in the range of 0.43% - 0.92% ( RSD, n = 11

  4. Atomic Resolution Images of Solid-Liquid Interfaces

    Science.gov (United States)

    Giambattista, Brian; McNairy, W. W.; Slough, C. G.; Johnson, A.; Bell, L. D.; Coleman, R. V.; Schneir, J.; Sonnenfeld, R.; Drake, B.; Hansma, P. K.

    1987-07-01

    A scanning tunneling microscope (STM) can provide atomic-resolution images of solids covered with a variety of liquids, including cryogenic fluids, both polar and nonpolar solvents, conductive aqueous solutions, oils, and even greases. This short overview includes images of solids covered with liquid nitrogen, liquid helium, paraffin oil, silicone oil, microscope immersion oil, silicone vacuum grease, fluorocarbon grease, glycerol, and salt water. These images show atoms, charge-density waves, grains in an evaporated metal film, and even corrosion processes as they occur in real time. The future includes not only basic research in surface science but also applied research in lithography, lubrication, catalysis, corrosion, electrochemistry, and perhaps even biology.

  5. Active Control of Fan Noise: Feasibility Study. Volume 3; Active Fan Noise Cancellation in the NASA Lewis Active Noise Control Fan Facility

    Science.gov (United States)

    Pla, Frederic G.; Hu, Ziqiang; Sutliff, Daniel L.

    1996-01-01

    This report describes the Active Noise Cancellation (ANC) System designed by General Electric and tested in the NASA Lewis Research Center's (LERC) 48 inch Active Noise Control Fan (ANCF). The goal of this study is to assess the feasibility of using wall mounted secondary acoustic sources and sensors within the duct of a high bypass turbofan aircraft engine for global active noise cancellation of fan tones. The GE ANC system is based on a modal control approach. A known acoustic mode propagating in the fan duct is canceled using an array of flush-mounted compact sound sources. The canceling modal signal is generated by a modal controller. Inputs to the controller are signals from a shaft encoder and from a microphone array which senses the residual acoustic mode in the duct. The key results are that the (6,0) was completely eliminated at the 920 Hz design frequency and substantially reduced elsewhere. The total tone power was reduced 6.8 dB (out of a possible 9.8 dB). Farfield reductions of 15 dB (SPL) were obtained. The (4,0) and (4,1) modes were reduced simultaneously yielding a 15 dB PWL decrease. The results indicate that global attenuation of PWL at the target frequency was obtained in the aft quadrant using an ANC actuator and sensor system totally contained within the duct. The quality of the results depended on precise mode generation. High spillover into spurious modes generated by the ANC actuator array caused less than optimum levels of PWL reduction. The variation in spillover is believed to be due to calibration procedure, but must be confirmed in subsequent tests.

  6. Unsteady flowfield simulation of ducted prop-fan configurations

    Science.gov (United States)

    Janus, J. M.; Horstman, Howard Z.; Whitfield, David L.

    1992-01-01

    A technique for the simulation of unsteady flows in and around complex rotating machinery is presented. Additional domain decomposition mechanisms are introduced which extend the range of applicability of software developed for the time-accurate simulation of rotating machinery flowfields. The flow models uses the unsteady 3D Euler equations, discretized as a finite-volume method, utilizing a high-resolution approximate Riemann solver for cell interface flux definitions. Multiblock domain decomposition is used to partition the field radially, axially, as well as circumferentially into an ordered arrangement of blocks which exhibit varying degrees of similarity. A general high-order numerical scheme is applied to satisfy the geometric conservation law. Two configurations are presented - ducted single rotation prop-fan and a rotor-deswirl vane combination which form a single stage fan. Comparisons are made to other numerical solutions for these geometries and to available experimental data.

  7. Natures of Rotating Stall Cell in a Diagonal Flow Fan

    Institute of Scientific and Technical Information of China (English)

    N. SHIOMI; K. KANEKO; T. SETOGUCHI

    2005-01-01

    In order to clarify the natures of a rotating stall cell, the experimental investigation was carried out in a high specific-speed diagonal flow fan. The pressure field on the casing wall and the velocity fields at the rotor inlet and outlet were measured under rotating stall condition with a fast response pressure transducer and a single slant hot-wire probe, respectively. The data were processed using the "Double Phase-Locked Averaging (DPLA)"technique, which enabled to obtain the unsteady flow field with a rotating stall cell in the relative co-ordinate system fixed to the rotor. As a result, the structure and behavior of the rotating stall cell in a high specific-speed diagonal flow fan were shown.

  8. Pattern recognition: A dialogue on racism in fan communities [symposium

    Directory of Open Access Journals (Sweden)

    TWC Editor

    2009-11-01

    Full Text Available In early 2009, science fiction fandom's online landscape erupted with discussions of race. A post regarding cultural appropriation on author Elizabeth Bear's blog sparked a wide-ranging conversation that soon became acrimonious, with professional science fiction and fantasy writers and fans of science fiction literature and media weighing in. More recently, criticisms of Patricia C. Wrede's decision to set her young adult novel, The Thirteenth Child (2009, in an America empty of indigenous people have spearheaded new waves of discussion. Often the more widely read summaries of these debates have focused on what they mean for writers and aspiring writers who plan to represent minority cultures in their works. But what has their significance been for members of fan communities?

  9. Wake Management Strategies for Reduction of Turbomachinery Fan Noise

    Science.gov (United States)

    Waitz, Ian A.

    1998-01-01

    The primary objective of our work was to evaluate and test several wake management schemes for the reduction of turbomachinery fan noise. Throughout the course of this work we relied on several tools. These include 1) Two-dimensional steady boundary-layer and wake analyses using MISES (a thin-shear layer Navier-Stokes code), 2) Two-dimensional unsteady wake-stator interaction simulations using UNSFLO, 3) Three-dimensional, steady Navier-Stokes rotor simulations using NEWT, 4) Internal blade passage design using quasi-one-dimensional passage flow models developed at MIT, 5) Acoustic modeling using LINSUB, 6) Acoustic modeling using VO72, 7) Experiments in a low-speed cascade wind-tunnel, and 8) ADP fan rig tests in the MIT Blowdown Compressor.

  10. Experimental investigation of unsteady fan flow interaction with downstream struts

    Science.gov (United States)

    Ng, W. F.; Obrien, W. F.; Olsen, T. L.

    1986-07-01

    In the present study of the unsteady pressure field produced on fan rotor blades by interaction with downstream struts, a single stage, low speed axial-flow fan was instrumented with blade-mounted high frequency pressure transducers. In addition, stationary pressure problems were used to map out the flowfield. Fluctuating pressure measurements are presented for blade midspan and 85-percent span on both the suction and pressure surfaces of the rotor blades at several positions of the downstream struts, and for two different flow coefficients. The strut is found to produce an effect on the unsteady pressure field on the rotor blades; this effect exceeds that due to the stator at design rotor-stator-strut spacing, but it rapidly declines as the struts are moved downstream.

  11. Advanced Trailing Edge Blowing Concepts for Fan Noise Control

    Directory of Open Access Journals (Sweden)

    Cezar RIZEA

    2012-03-01

    Full Text Available This study documents trailing edge blowing research performed to reduce rotor / stator interaction noise in turbofan engines. The existing technique of filling every velocity deficit requires a large amount of air and is therefore impractical. The purpose of this research is to investigate new blowing configurations in order to achieve noise reduction with lesser amounts of air. Using the new configurations air is not injected into every fan blade, but is instead varied circumferentially. For example, blowing air may be applied to alternating fan blades. This type of blowing configuration both reduces the amount of air used and changes the spectral shape of the tonal interaction noise. The original tones at the blade passing frequency and its harmonics are reduced and new tones are introduced between them. This change in the tonal spectral shape increases the performance of acoustic liners used in conjunction with trailing edge blowing.

  12. Euler/Navier-Stokes Solvers Applied to Ducted Fan Configurations

    Science.gov (United States)

    Keith, Theo G., Jr.; Srivastava, Rakesh

    1997-01-01

    Due to noise considerations, ultra high bypass ducted fans have become a more viable design. These ducted fans typically consist of a rotor stage containing a wide chord fan and a stator stage. One of the concerns for this design is the classical flutter that keeps occurring in various unducted fan blade designs. These flutter are catastrophic and are to be avoided in the flight envelope of the engine. Some numerical investigations by Williams, Cho and Dalton, have suggested that a duct around a propeller makes it more unstable. This needs to be further investigated. In order to design an engine to safely perform a set of desired tasks, accurate information of the stresses on the blade during the entire cycle of blade motion is required. This requirement in turn demands that accurate knowledge of steady and unsteady blade loading be available. Aerodynamic solvers based on unsteady three-dimensional analysis will provide accurate and fast solutions and are best suited for aeroelastic analysis. The Euler solvers capture significant physics of the flowfield and are reasonably fast. An aerodynamic solver Ref. based on Euler equations had been developed under a separate grant from NASA Lewis in the past. Under the current grant, this solver has been modified to calculate the aeroelastic characteristics of unducted and ducted rotors. Even though, the aeroelastic solver based on three-dimensional Euler equations is computationally efficient, it is still very expensive to investigate the effects of multiple stages on the aeroelastic characteristics. In order to investigate the effects of multiple stages, a two-dimensional multi stage aeroelastic solver was also developed under this task, in collaboration with Dr. T. S. R. Reddy of the University of Toledo. Both of these solvers were applied to several test cases and validated against experimental data, where available.

  13. Instrumentation for propulsion systems development. [high speed fans and turbines

    Science.gov (United States)

    Warshawsky, I.

    1978-01-01

    Apparatus and techniques developed or used by NASA-Lewis to make steady state or dynamic measurements of gas temperature, pressure, and velocity and of the temperature, tip clearance, and vibration of the blades of high-speed fans or turbines are described. The advantages and limitations of each instrument and technique are discussed and the possibility of modifying them for use in developing various propulsion systems is suggested.

  14. GENERALIZATIONS OF KY FAN'S THEOREM ON BEST APPROXIMATIONS

    Institute of Scientific and Technical Information of China (English)

    T.D.Narang

    2009-01-01

    In 1969, Ky Fan[3] proved that for any continuous function f from a compact convex subset M of a normed linear space X into X, there exists x ∈ M such that ||f(x)-x|| = dist(f(x),M). Since then, there have appeared several generalizations, extensions and applications of this result. This paper also deals with some extensions and generalizations of this result when the underlying spaces are convex metric spaces.

  15. The Diagonal Compression Field Method using Circular Fans

    DEFF Research Database (Denmark)

    Hansen, Thomas

    2005-01-01

    This paper presents a new design method, which is a modification of the diagonal compression field method, the modification consisting of the introduction of circular fan stress fields. The traditional method does not allow changes of the concrete compression direction throughout a given beam...... fields may be used whenever changes in the concrete compression direction are desired. To illustrate the new design method, a specific example of a prestressed concrete beam is calculated....

  16. Fans of Columbine shooters Eric Harris and Dylan Klebold

    OpenAIRE

    Andrew Ryan Rico

    2015-01-01

    On April 20, 1999, Eric Harris and Dylan Klebold murdered 12 students and one teacher at Columbine High School in Littleton, Colorado, in what was then the deadliest school shooting in American history. Despite causing a national panic and serving as a flash point for larger narratives on bullying, gun control, and media violence, both boys have gained active online fans. These fandoms dedicated to the Columbine shooters are widely referred to as dark examples of Internet communities, while t...

  17. Aerodynamic optimisation of an industrial axial fan blade

    OpenAIRE

    2006-01-01

    Numerical optimisation methods have successfully been used for a variety of aerodynamic design problems over quite a few years. However the application of these methods to the aerodynamic blade shape optimisation of industrial axial fans has received much less attention in the literature probably given the fact that the majority of resources available to develop these automated design approaches is to be found in the aerospace field. This work presents the develo...

  18. Dual Fan Separator within the Universal Waste Management System

    Science.gov (United States)

    Stapleton, Tom; Converse, Dave; Broyan, James Lee, Jr.

    2014-01-01

    Since NASA's new spacecraft in development for both LEO and Deep Space capability have considerable crew volume reduction in comparison to the Space Shuttle, the need became apparent for a smaller commode. In response the Universal Waste Management System (UWMS) was designed, resulting in an 80% volume reduction from the last US commode, while enhancing performance. The ISS WMS and previous shuttle commodes have a fan supplying air flow to capture feces and a separator to capture urine and separate air from the captured air/urine mixture. The UWMS combined both rotating equipment components into a single unit, referred to at the Dual Fan Separator (DFS). The combination of these components resulted in considerable packaging efficiency and weight reduction, removing inter-component plumbing, individual mounting configurations and required only a single motor and motor controller, in some of the intended UWMS platform applications the urine is pumped to the ISS Urine Processor Assembly (UPA) system. It requires the DFS to include less than 2.00% air inclusion, by volume, in the delivered urine. The rotational speed needs to be kept as low as possible in centrifugal urine separators to reduce air inclusion in the pumped fluid, while fans depend on rotational speed to develop delivered head. To satisfy these conflicting requirements, a gear reducer was included, allowing the fans to rotate at a much higher speed than the separator. This paper outlines the studies and analysis performed to develop the DFS configuration. The studies included a configuration trade study, dynamic stability analysis of the rotating bodies and a performance analysis of included labyrinth seals. NASA is considering a program to fly the UWMS aboard the ISS as a flight experiment. The goal of this activity is to advance the Technical Readiness Level (TRL) of the DFS and determine if the concept is ready to be included as part of the flight experiment deliverable.

  19. Stable fan filter design using two-variable reactance functions

    Science.gov (United States)

    Bruton, L. T.; Bartley, N. R.

    1982-03-01

    Two-variable reactance transformation (as proposed by King et al., 1982) for the design of stable two-dimensional recursive fan filters with narrow stopbands is compared with the design method proposed by Bruton et al. (1981) using numerical optimization of a resistively terminated (2 + n sub 1 + n sub 2)-port network. The method of King et al. is found to be definitely more simple to design.

  20. iFan iphone风力充电器

    Institute of Scientific and Technical Information of China (English)

    2011-01-01

    你还在每天为了寻找为iPhone充电的电源而烦恼么?这里有一款非常给力的iPhone手机配件——iFan iPhone风力充电器。在充当保护套之外它头顶上的风扇可以收集风能转化为电能给iPhone充电。

  1. Evaluation of Retrofit Variable-Speed Furnace Fan Motors

    Energy Technology Data Exchange (ETDEWEB)

    Aldrich, R.; Williamson, J.

    2014-01-01

    In conjunction with the New York State Energy Research and Development Authority (NYSERDA) and Proctor Engineering Group, Ltd. (PEG), the Consortium for Advanced Residential Buildings (CARB) has evaluated the Concept 3 (tm) replacement motors for residential furnaces. These brushless, permanent magnet (BPM) motors can use much less electricity than their PSC (permanent split capacitor) predecessors. This evaluation focuses on existing homes in the heating-dominated climate of upstate New York with the goals of characterizing field performance and cost-effectiveness. The results of this study are intended to be useful to home performance contractors, HVAC contractors, and home efficiency program stakeholders. The project includes eight homes in and near Syracuse, NY. Tests and monitoring was performed both before and after fan motors were replaced. Average fan power reductions were approximately 126 Watts during heating and 220 Watts during cooling operation. Over the course of entire heating and cooling seasons, these translated into average electric energy savings of 163 kWh. Average cost savings were $20 per year. Homes where the fan was used outside of heating and cooling mode saved an additional $42 per year on average. Results indicate that BPM replacement motors will be most cost-effective in HVAC systems with longer run times and relatively low duct static pressures. More dramatic savings are possible if occupants use the fan-only setting when there is no thermal load. There are millions of cold-climate, U.S. homes that meet these criteria, but the savings in most homes tested in this study were modest.

  2. Streaming Scholarship: Using Fan Vids to Teach "Harry Potter"

    Science.gov (United States)

    Winters, Sarah Fiona

    2013-01-01

    This article argues that Harry Potter fan vids can be used in the classroom as works of secondary criticism about J. K. Rowling's primary text. It makes two claims: the first is that vids can be read as criticism of a particular text (in this case Harry Potter) alongside other critical essays on that text; the second is that the practice of…

  3. Streaming Scholarship: Using Fan Vids to Teach "Harry Potter"

    Science.gov (United States)

    Winters, Sarah Fiona

    2013-01-01

    This article argues that Harry Potter fan vids can be used in the classroom as works of secondary criticism about J. K. Rowling's primary text. It makes two claims: the first is that vids can be read as criticism of a particular text (in this case Harry Potter) alongside other critical essays on that text; the second is that the practice of…

  4. Oil risk in oil stocks

    NARCIS (Netherlands)

    Scholtens, Bert; Wang, L

    2008-01-01

    We assess the oil price sensitivities and oil risk premiums of NYSE listed oil & gas firms' returns by using a two-step regression analysis under two different arbitrage pricing models. Thus, we apply the Fama and French (1992) factor returns in a study of oil stocks. In all, we find that the return

  5. Oil risk in oil stocks

    NARCIS (Netherlands)

    Scholtens, Bert; Wang, L

    2008-01-01

    We assess the oil price sensitivities and oil risk premiums of NYSE listed oil & gas firms' returns by using a two-step regression analysis under two different arbitrage pricing models. Thus, we apply the Fama and French (1992) factor returns in a study of oil stocks. In all, we find that the return

  6. Auxiliary lift propulsion system with oversized front fan

    Energy Technology Data Exchange (ETDEWEB)

    Castells, O.T.; Johnson, J.E.; Rundell, D.J.

    1980-09-16

    A propulsion system for use primarily in V/STOL aircraft is provided with a variable cycle, double bypass gas turbofan engine and a remote augmenter to produce auxiliary lift. The fan is oversized in air-pumping capability with respect to the cruise flight requirements of the remainder of the engine and a variable area, low pressure turbine is capable of supplying varying amounts of rotational energy to the oversized fan, thereby modulating its speed and pumping capability. During powered lift flight, the variable cycle engine is operated in the single bypass mode with the oversized fan at its maximum pumping capability. In this mode, substantially all of the bypass flow is routed as an auxiliary airstream to the remote augmenter where it is mixed with fuel, burned and exhausted through a vectorable nozzle to produce thrust for lifting. Additional lift is generated by the high energy products of combustion of the variable cycle engine which are further energized in an afterburner and exhausted through a thrust vectorable nozzle at the rear of the engine.

  7. Characteristics of tip-leakage flow in an axial fan

    Science.gov (United States)

    Park, Keuntae; Choi, Haecheon; Choi, Seokho; Sa, Yongcheol

    2014-11-01

    An axial fan with a shroud generates complicated vortical structures by the interaction of the axial flow with the fan blades and shroud near the blade tips. Large eddy simulation (LES) is performed for flow through a forward-swept axial fan, operating at the design condition of Re = 547,000 based on the radius of blade tip and the tip velocity. A dynamic global model (Lee et al. 2010) is used for a subgrid-scale model, and an immersed boundary method in a non-inertial reference frame (Kim & Choi 2006) is adopted for the present simulation. It is found that two vortical structures are formed near the blade tip: the main tip leakage vortex (TLV) and the auxiliary TLV. The main TLV is initiated near the leading edge, develops downstream, and impinges on the pressure surface of the next blade, where the pressure fluctuations and turbulence intensity become high. On the other hand, the auxiliary TLV is initiated at the aft part of the blade but is relatively weak such that it merges with the main TLV. Supported by the KISTI Supercomputing Center (KSC-2014-C2-014).

  8. Investigation of fatigue fracture of generator-rotor fan blades

    Energy Technology Data Exchange (ETDEWEB)

    Sameezadeh, Mahmood; Farhangi, Hassan [School of Metallurgy and Materials Engineering, Univ. of Tehran (Iran); Soltani, Nasser [School of Mechanical Engineering, Univ. of Tehran (Iran); Ataei, Peyman [Dept. of Metallurgy and Materials Engineering, South Tehran Branch of Azad Univ., Tehran (Iran)

    2009-11-15

    The failure of a rotating axial flow fan of a 123 MW electric power generator unit is analyzed. The fan was mounted on the generator-rotor at the turbine end. Initial investigations showed that three fan blades had fractured just about 11 h after resuming operation following the last overhaul, causing extensive damage to the unit. The failure of the blades was investigated using fractographic and microstructural characterization techniques as well as mechanical evaluations. Based on fractographic observations high cycle fatigue was identified as the failure mechanism. Formation of multiple primary cracks which coalesced during crack growth to form shallow and semi-elliptical crack geometry was indicative of the influence of additional bending stresses, probably resulting from excessive vibrations. Using fracture mechanics principles, the magnitude of the maximum stress at the time of final fracture of the first broken blade was estimated to be more than 3 times higher than the design operating stress. Furthermore, crack growth lifetime of the blades was evaluated using FRANC3D software. It was found that an operating period of just about one hour was required for small initial cracks to propagate to final failure under the action of excessive bending stresses. (orig.)

  9. Effects of Bifurcations on Aft-Fan Engine Nacelle Noise

    Science.gov (United States)

    Nark, Douglas M.; Farassat, Fereidoun; Pope, D. Stuart; Vatsa, Veer N.

    2004-01-01

    Aft-fan engine nacelle noise is a significant factor in the increasingly important issue of aircraft community noise. The ability to predict such noise within complex duct geometries is a valuable tool in studying possible noise attenuation methods. A recent example of code development for such predictions is the ducted fan noise propagation and radiation code CDUCT-LaRC. This work focuses on predicting the effects of geometry changes (i.e. bifurcations, pylons) on aft fan noise propagation. Beginning with simplified geometries, calculations show that bifurcations lead to scattering of acoustic energy into higher order modes. In addition, when circumferential mode number and the number of bifurcations are properly commensurate, bifurcations increase the relative importance of the plane wave mode near the exhaust plane of the bypass duct. This is particularly evident when the bypass duct surfaces include acoustic treatment. Calculations involving more complex geometries further illustrate that bifurcations and pylons clearly affect modal content, in both propagation and radiation calculations. Additionally, results show that consideration of acoustic radiation results may provide further insight into acoustic treatment effectiveness for situations in which modal decomposition may not be straightforward. The ability of CDUCT-LaRC to handle complex (non-axisymmetric) multi-block geometries, as well as axially and circumferentially segmented liners, allows investigation into the effects of geometric elements (bifurcations, pylons).

  10. River terraces and alluvial fans: The case for an integrated Quaternary fluvial archive

    Science.gov (United States)

    Mather, A. E.; Stokes, M.; Whitfield, E.

    2017-06-01

    The fluvial archive literature is dominated by research on river terraces with appropriate mention of adjacent environments such as lakes. Despite modern sedimentary basins comprising a significant (>88%) volume of distributive fluvial systems, of which alluvial fans (>1 km, archive community. Published literature is used to examine both thematic and geographical based benefits of alluvial fan research that can assist understanding of Quaternary fluvial archives. 3 regional case studies are presented that illustrate the interaction between alluvial fan and river terrace archives at Quaternary time-scales at 3 different stages of landscape evolution. These are i) continuous mountain front alluvial fans interacting with a non incising but laterally eroding axial fluvial system; ii) alluvial fans which transition into fluvial terraces as sedimentary basins shift from net aggradation to net incision and iii) tributary-junction alluvial fans that develop predominantly within incising river valley systems. A simple conceptual model is proposed to summarise the dynamic role of alluvial fans within this landscape context. The alluvial fans act as potential 'buffers' between hillslopes and river terrace records under 'top down' climate-driven high sediment supply and alluvial fan aggradation, and 'couplers' during periods of less sediment (in relation to water) discharge and alluvial fan incision. These dynamics will change with the addition of 'bottom up' controls such as main river incision, which will typically enhance the coupling effect of both systems.

  11. The Conceptual Design of High Pressure Reversible Axial Tunnel Ventilation Fans

    Directory of Open Access Journals (Sweden)

    A. G. Sheard

    2012-01-01

    Full Text Available Tunnel ventilation fans, classically, must have the ability to both supply and extract air from a tunnel system, with the operator's choice dependent on the tunnel ventilation system's operating mode most appropriate at any given point in time. Consequently, tunnel ventilation fans must incorporate a reversible aerodynamic design which limits the maximum fan pressure rise. This paper presents three high pressure reversible fan concepts. These comprise a two-stage counter rotating fan, a single-stage high speed fan, and a two-stage fan with a single motor and impeller on each end of the motor shaft. The authors consider the relative merits of each concept. The third concept offers the most compact fan, transform, silencer, and damper package size. The authors discuss the mechanical design challenges that occur with a two-stage fan with a single motor and impeller on each end of the motor shaft. They present and consider a selected motor bearing arrangement and casing design for maintainability. Finally, the authors present both prototype fan and full-scale package aerodynamic and acoustic performance, before discussing the challenges presented by high temperature certification in accordance with the requirements of EN 12101-3: 2012.

  12. Numerical investigation of geometric parameter effects on the aerodynamic performance of a Bladeless fan

    Directory of Open Access Journals (Sweden)

    Mohammad Jafari

    2016-03-01

    Full Text Available Aerodynamic performance of a Bladeless fan is numerically investigated considering the effect of five geometric parameters. Airflow through this fan was analyzed by simulating a Bladeless fan within a 2 m × 2 m × 4 m room. Analysis of the flow field inside the fan and the evaluation of its performance were obtained by solving conservations of mass and momentum equations for the aerodynamic investigations. In order to design the Bladeless fan an Eppler 473 airfoil profile was used as the cross section of the fan. Five distinct parameters, namely height of cross section of the fan, outlet angle of the flow relative to the fan axis, thickness of airflow outlet slit, hydraulic diameter, and aspect ratio for circular and quadratic cross sections were considered. Validating 3-D numerical results, experimental results of a round jet showed good agreement with those of the simulation data. The multiplier factor M is defined to show the ratio of the outlet flow rate to inlet flow rate from the fan. The obtained numerical results showed that the Discharge ratio has the maximum value for the height of 3 cm. The numerical outcomes of outlet thickness variation indicate that this parameter is one of the most influential parameters on the aerodynamic performance of a Bladeless fan. The results for the outlet thicknesses of 1, 2 and 3 mm showed that the Discharge ratio increased significantly when the outlet thickness decreased.

  13. Experimental and Numerical Investigation of a 60cm Diameter Bladeless Fan

    Directory of Open Access Journals (Sweden)

    mohammad jafari

    2016-01-01

    Full Text Available Bladeless fan is a novel type of fan with an unusual geometry and unique characteristics. This type of fan has been recently developed for domestic applications in sizes typically up to 30cm diameter. In the present study, a Bladeless fan with a diameter of 60cm was designed and constructed, in order to investigate feasibility of its usage in various industries with large dimensions. Firstly, flow field passed through this fan was studied by 3D modeling. Aerodynamic and aeroacoustic performance of the fan were considered via solving the conservation of mass and momentum equations in their unsteady form. To validate the acoustic code, NACA 0012 airfoil was simulated in a two dimension domain and the emitted noise was calculated for Re=2×105. Good agreement between numerical and experimental results was observed by applying FW-H equations for predicting noise of the fan. To validate the simulated aerodynamic results, a Bladeless fan with a 60cm diameter was constructed and experimentally tested. In addition, the difference between the experimental and numerical results was acceptable for this fan. Moreover, the experimental results in the present study showed that this fan is capable to be designed and used for various industrial applications.

  14. Health assessment of cooling fan bearings using wavelet-based filtering.

    Science.gov (United States)

    Miao, Qiang; Tang, Chao; Liang, Wei; Pecht, Michael

    2012-12-24

    As commonly used forced convection air cooling devices in electronics, cooling fans are crucial for guaranteeing the reliability of electronic systems. In a cooling fan assembly, fan bearing failure is a major failure mode that causes excessive vibration, noise, reduction in rotation speed, locked rotor, failure to start, and other problems; therefore, it is necessary to conduct research on the health assessment of cooling fan bearings. This paper presents a vibration-based fan bearing health evaluation method using comblet filtering and exponentially weighted moving average. A new health condition indicator (HCI) for fan bearing degradation assessment is proposed. In order to collect the vibration data for validation of the proposed method, a cooling fan accelerated life test was conducted to simulate the lubricant starvation of fan bearings. A comparison between the proposed method and methods in previous studies (i.e., root mean square, kurtosis, and fault growth parameter) was carried out to assess the performance of the HCI. The analysis results suggest that the HCI can identify incipient fan bearing failures and describe the bearing degradation process. Overall, the work presented in this paper provides a promising method for fan bearing health evaluation and prognosis.

  15. Health Assessment of Cooling Fan Bearings Using Wavelet-Based Filtering

    Directory of Open Access Journals (Sweden)

    Qiang Miao

    2012-12-01

    Full Text Available As commonly used forced convection air cooling devices in electronics, cooling fans are crucial for guaranteeing the reliability of electronic systems. In a cooling fan assembly, fan bearing failure is a major failure mode that causes excessive vibration, noise, reduction in rotation speed, locked rotor, failure to start, and other problems; therefore, it is necessary to conduct research on the health assessment of cooling fan bearings. This paper presents a vibration-based fan bearing health evaluation method using comblet filtering and exponentially weighted moving average. A new health condition indicator (HCI for fan bearing degradation assessment is proposed. In order to collect the vibration data for validation of the proposed method, a cooling fan accelerated life test was conducted to simulate the lubricant starvation of fan bearings. A comparison between the proposed method and methods in previous studies (i.e., root mean square, kurtosis, and fault growth parameter was carried out to assess the performance of the HCI. The analysis results suggest that the HCI can identify incipient fan bearing failures and describe the bearing degradation process. Overall, the work presented in this paper provides a promising method for fan bearing health evaluation and prognosis.

  16. Large scale application of vibration sensors for fan monitoring at commercial layer hen houses.

    Science.gov (United States)

    Chen, Yan; Ni, Ji-Qin; Diehl, Claude A; Heber, Albert J; Bogan, Bill W; Chai, Li-Long

    2010-01-01

    Continuously monitoring the operation of each individual fan can significantly improve the measurement quality of aerial pollutant emissions from animal buildings that have a large number of fans. To monitor the fan operation by detecting the fan vibration is a relatively new technique. A low-cost electronic vibration sensor was developed and commercialized. However, its large scale application has not yet been evaluated. This paper presents long-term performance results of this vibration sensor at two large commercial layer houses. Vibration sensors were installed on 164 fans of 130 cm diameter to continuously monitor the fan on/off status for two years. The performance of the vibration sensors was compared with fan rotational speed (FRS) sensors. The vibration sensors exhibited quick response and high sensitivity to fan operations and therefore satisfied the general requirements of air quality research. The study proved that detecting fan vibration was an effective method to monitor the on/off status of a large number of single-speed fans. The vibration sensor itself was $2 more expensive than a magnetic proximity FRS sensor but the overall cost including installation and data acquisition hardware was $77 less expensive than the FRS sensor. A total of nine vibration sensors failed during the study and the failure rate was related to the batches of product. A few sensors also exhibited unsteady sensitivity. As a new product, the quality of the sensor should be improved to make it more reliable and acceptable.

  17. Atomic rivals

    Energy Technology Data Exchange (ETDEWEB)

    Goldschmidt, B.

    1990-01-01

    This book is a memoir of rivalries among the Allies over the bomb, by a participant and observer. Nuclear proliferation began in the uneasy wartime collaboration of the United States, England, Canada, and Free France to produce the atom bomb. Through the changes of history, a young French chemist had a role in almost every act of this international drama. This memoir is based on Goldschmidt's own recollections, interviews with other leading figures, and 3,000 pages of newly declassified documents in Allied archives. From his own start as Marie Curie's lab assistant, Goldschmidt's career was closely intertwined with Frances complicated rise to membership in the nuclear club. As a refugee from the Nazis, he became part of the wartime nuclear energy project in Canada and found himself the only French scientist to work (although briefly) on the American atom bomb project.

  18. Study on the performance improvement of multiblade fans. Effects of suction cones; Tayoku fan no seino kaizen ni kansuru kenkyu. Suction cone no eikyo

    Energy Technology Data Exchange (ETDEWEB)

    Kuratani, F.; Ogawa, T. [Hyogo University of Teacher Education, Hyogo (Japan); Yamamoto, S.

    1999-07-25

    In order to improve the performance of a multiblade fan, the effects of three types of suction cones of the fan casing on the fan efficiency and noise are investigated experimentally. The first type of the suction cone is the insertion type, which is inserted into the inside of the fan impeller. The second type is the extrusion type, which extrudes outside from the casing surface. The third type is the combination type of two types. The results of those three types are compared with those of the commonly used suction cone. The followings are made clear: (1) The insertion type and the extrusion type are effective in improving the efficiency and reducing noise. (2) The optimal lengths of the insertion and the extrusion exist. (3) The combination type is more effective in improving the efficiency. (4) The combination type with the skewed cutoff of the fan casing shows the best effect. (author)

  19. Atomic physics

    Energy Technology Data Exchange (ETDEWEB)

    Livingston, A.E.; Kukla, K.; Cheng, S. [Univ. of Toledo, OH (United States)] [and others

    1995-08-01

    In a collaboration with the Atomic Physics group at Argonne and the University of Toledo, the Atomic Physics group at the University of Notre Dame is measuring the fine structure transition energies in highly-charged lithium-like and helium-like ions using beam-foil spectroscopy. Precise measurements of 2s-2p transition energies in simple (few-electron) atomic systems provide stringent tests of several classes of current atomic- structure calculations. Analyses of measurements in helium-like Ar{sup 16+} have been completed, and the results submitted for publication. A current goal is to measure the 1s2s{sup 3}S{sub 1} - 1s2p{sup 3}P{sub 0} transition wavelength in helium-like Ni{sup 26+}. Measurements of the 1s2s{sup 2}S{sub 1/2} - 1s2p{sup 2}P{sub 1/2,3/2} transition wavelengths in lithium-like Kr{sup 33+} is planned. Wavelength and lifetime measurements in copper-like U{sup 63+} are also expected to be initiated. The group is also participating in measurements of forbidden transitions in helium-like ions. A measurement of the lifetime of the 1s2s{sup 3}S{sub 1} state in Kr{sup 34+} was published recently. In a collaboration including P. Mokler of GSI, Darmstadt, measurements have been made of the spectral distribution of the 2E1 decay continuum in helium-like Kr{sup 34+}. Initial results have been reported and further measurements are planned.

  20. The Atomic orbitals of the topological atom

    OpenAIRE

    Ramos-Cordoba, Eloy; Salvador Sedano, Pedro

    2013-01-01

    The effective atomic orbitals have been realized in the framework of Bader's atoms in molecules theory for a general wavefunction. This formalism can be used to retrieve from any type of calculation a proper set of orthonormalized numerical atomic orbitals, with occupation numbers that sum up to the respective Quantum Theory of Atoms in Molecules (QTAIM) atomic populations. Experience shows that only a limited number of effective atomic orbitals exhibit significant occupation numbers. These c...

  1. Design and Research of Intelligent Remote Control Fan Based on Single Chip Microcomputer and Bluetooth Technology

    Directory of Open Access Journals (Sweden)

    Zhang Xue-Xia

    2017-01-01

    Full Text Available This paper is designed for intelligent remote control fans. The design of the microcontroller as the core, the sensor, Bluetooth and Andrews system applied to the design of intelligent remote control fan. According to the temperature sensor to achieve the indoor temperature collection, to achieve and set the temperature comparison, thus affecting the fan speed. At the same time, the system according to the infrared sensor components to detect external factors, in order to achieve the running or stopping of the fan, that is, to achieve intelligent control of the fan. In addition, the system achieve the Bluetooth and mobile phone Andrews system of effective combination, and through the software program to complete the fan remote operation and wind speed control.

  2. Numerical simulation of air flow field in high-pressure fan with splitter blades

    Institute of Scientific and Technical Information of China (English)

    Jianfeng LI; Junfu LU; Hai ZHANG; Qing LIU; Guangxi YUE

    2008-01-01

    For a deeper understanding of the flow char-acteristics in the high-pressure centrifugal blower of a fan of Model 9-26 with splitter blades, a three dimensional (3-D) numerical simulation of air flows in the fan was con-ducted with FLUENT software. The standard k-ε tur-bulent model and unstructured grids were used. The computational fluid dynamics (CFD) results showed that the performance of a fan could be improved by adding the splitter blades in the channel among the leaf blades. Under operational conditions, with the presence of splitter blades, the air flow rate of the fan increased about 5% and the total pressure at the outlet of the fan increased about 10% on average. It was also found that the length of the splitter blades affected the air flow and pressure drop. There is an optimal value for the length. The simulation results provide helpful information for improving the fan performance.

  3. Tectonic and climatic controls on fan systems: The Kohrud mountain belt, Central Iran

    Science.gov (United States)

    Jones, Stuart J.; Arzani, Nasser; Allen, Mark B.

    2014-04-01

    Late Pleistocene to Holocene fans of the Kohrud mountain belt (Central Iran) illustrate the problems of differentiating tectonic and climatic drivers for the sedimentary signatures of alluvial fan successions. It is widely recognised that tectonic processes create the topography that causes fan development. The existence and position of fans along the Kohrud mountain belt, NE of Esfahan, are controlled by faulting along the Qom-Zefreh fault system and associated fault zones. These faults display moderate amounts of historical and instrumental seismicity, and so may be considered to be tectonically active. However, fluvial systems on the fans are currently incising in response to low Gavkhoni playa lake levels since the mid-Holocene, producing incised gullies on the fans up to 30 m deep. These gullies expose an interdigitation of lake deposits (dominated by fine-grained silts and clays with evaporites) and coarse gravels that characterise the alluvial fan sediments. The boundaries of each facies are mostly sharp, with fan sediments superimposed on lake sediments with little to no evidence of reworking. In turn, anhydrite-glauberite, mirabilite and halite crusts drape over the gravels, recording a rapid return to still water, shallow ephemeral saline lake sedimentation. Neither transition can be explained by adjustment of the hinterland drainage system after tectonic uplift. The potential influence in Central Iran of enhanced monsoons, the northward drift of the Intertopical Convergence Zone (ITCZ) and Mediterranean climates for the early Holocene (~ 6-10 ka) point to episodic rainfall (during winter months) associated with discrete high magnitude floods on the fan surfaces. The fan sediments were deposited under the general influence of a highstand playa lake whose level was fluctuating in response to climate. This study demonstrates that although tectonism can induce fan development, it is the sensitive balance between aridity and humidity resulting from changes in

  4. Seafloor-precipitated carbonate fans in the Neoproterozoic Rainstorm Member, Johnnie Formation, Death Valley Region, USA

    OpenAIRE

    Pruss, Sara Brady; Corsetti, Frank A.; Fischer, Woodward W.

    2008-01-01

    Cm-sized carbonate seafloor fans occur in the Neoproterozoic Rainstorm Member of the Johnnie Formation, Death Valley, USA. The fans formed in a mixed carbonate-clastic succession near storm wave base at the base of parasequences on a storm-dominated ramp. Petrographic observations indicate that the fans were originally precipitated as aragonite and later inverted to calcite during diagenesis. Although not directly dated, the Rainstorm Member preserves a large magnitude negative carbon isotopi...

  5. Alluvial fan flooding in the Department of Pocito, Province of San Juan, Argentina

    Institute of Scientific and Technical Information of China (English)

    LauraPatriciaPerucca; JuanParedes

    2004-01-01

    The study consists of the identification of landforms subject to alluvial fan flooding in active sectors of the Zonda range piedmont. In the Department of Pocito, located about 5 km southwest of San Juan City, a series of alluvial fans have been identified. These alluvial fans are located downstream of the natural drainage basins covering an area of approximately 130 km2 towards the eastern slopes of the Zonda range at a median elevation of 2,000 m a.s.l.

  6. Quantitative reconstruction of late Holocene surface evolution on an alpine debris-flow fan

    Science.gov (United States)

    Schürch, Peter; Densmore, Alexander L.; Ivy-Ochs, Susan; Rosser, Nick J.; Kober, Florian; Schlunegger, Fritz; McArdell, Brian; Alfimov, Vasili

    2016-12-01

    Debris-flow fans form a ubiquitous record of past debris-flow activity in mountainous areas, and may be useful for inferring past flow characteristics and consequent future hazard. Extracting information on past debris flows from fan records, however, requires an understanding of debris-flow deposition and fan surface evolution; field-scale studies of these processes have been very limited. In this paper, we document the patterns and timing of debris-flow deposition on the surface of the large and exceptionally active Illgraben fan in southwestern Switzerland. We use terrain analysis, radiocarbon dating of sediment fill in the Illgraben catchment, and cosmogenic 10Be and 36Cl exposure dating of debris-flow deposits on the fan to constrain the temporal evolution of the sediment routing system in the catchment and on the fan during the past 3200 years. We show that the fan surface preserves a set of debris-flow lobes that were predominantly deposited after the occurrence of a large rock avalanche near the fan apex at about 3200 years ago. This rock avalanche shifted the apex of the fan and impounded sediment within the Illgraben catchment. Subsequent evolution of the fan surface has been governed by both lateral and radial shifts in the active depositional lobe, revealed by the cosmogenic radionuclide dates and by cross-cutting geometrical relationships on the fan surface. This pattern of frequent avulsion and fan surface occupation provides field-scale evidence of the type of large-scale compensatory behavior observed in experimental sediment routing systems.

  7. Low-pressure reversible axial fan with straight profile blades and relatively high efficiency

    OpenAIRE

    2012-01-01

    The paper presents the design and operating characteristics of a model of reversible axial fan with only one impeller, whose reversibility is achieved by changing the direction of rotation. The fan is designed for the purpose of providing alternating air circulation in wood dryers in order to reduce the consumption of electricity for the fan and increase energy efficiency of the entire dryer. To satisfy the reversibility of flow, the shape of the blade profile is symmetrical along the l...

  8. Timing and nature of alluvial fan development along the Chajnantor Plateau, northern Chile

    Science.gov (United States)

    Cesta, Jason M.; Ward, Dylan J.

    2016-11-01

    Alluvial systems in the Atacama Desert provide a unique opportunity to elucidate the sedimentary response to climate variability, particularly changes in precipitation, in hyperarid environments. Alluvial fans along the eastern margin of the Salar de Atacama, adjacent to the Chajnantor Plateau in the Atacama Desert of northern Chile, provide an archive of climate-modulated sediment transfer and erosion at an extreme of Earth's climate. Three regional alluvial fan surfaces (Qf1 [oldest] to Qf3 [youngest]) were mapped along the western flank of the Chajnantor Plateau. The alluvial fans were examined with geomorphic and terrestrial cosmogenic 36Cl surface exposure dating methods to define the timing of alluvial fan formation and to determine the role of climatic processes on fan development in a hyperarid environment. Alluvial fans in the study area are comprised of hyperconcentrated flow and boulder-rich debris flow deposits that reflect deposition transitioning between cohesive and noncohesive regimes. Alluvial fan surfaces yield exposure ages that range from 49.6 ± 4.4 to 194 ± 12 ka, while debris flow boulders yield exposure ages ranging from 12.4 ± 2.1 to 229 ± 53 ka. Cosmogenic 36Cl exposure ages indicate that abandonment of alluvial fan surfaces Qf1, Qf2, and Qf3 date to 175 ± 22.6 ka (MIS 6), 134.5 ± 9.18 ka (MIS 6), and 20.07 ± 6.26 ka (MIS 2), respectively. A 36Cl concentration-depth profile through alluvial fan Qf1 suggests a simple depositional history with minimal nuclide inheritance implying relatively rapid aggradation (6 m in ca. 25 kyr) followed by surface abandonment ca. 180-200 ka. Our data support a strong climatic control on alluvial fan evolution in the region, and we propose that the alluvial fans along the margins of the Salar de Atacama form according to the humid model of fan formation.

  9. Multi-objective optimization design and experimental investigation of centrifugal fan performance

    Science.gov (United States)

    Zhang, Lei; Wang, Songling; Hu, Chenxing; Zhang, Qian

    2013-11-01

    Current studies of fan performance optimization mainly focus on two aspects: one is to improve the blade profile, and another is only to consider the influence of single impeller structural parameter on fan performance. However, there are few studies on the comprehensive effect of the key parameters such as blade number, exit stagger angle of blade and the impeller outlet width on the fan performance. The G4-73 backward centrifugal fan widely used in power plants is selected as the research object. Based on orthogonal design and BP neural network, a model for predicting the centrifugal fan performance parameters is established, and the maximum relative errors of the total pressure and efficiency are 0.974% and 0.333%, respectively. Multi-objective optimization of total pressure and efficiency of the fan is conducted with genetic algorithm, and the optimum combination of impeller structural parameters is proposed. The optimized parameters of blade number, exit stagger angle of blade and the impeller outlet width are seperately 14, 43.9°, and 21 cm. The experiments on centrifugal fan performance and noise are conducted before and after the installation of the new impeller. The experimental results show that with the new impeller, the total pressure of fan increases significantly in total range of the flow rate, and the fan efficiency is improved when the relative flow is above 75%, also the high efficiency area is broadened. Additionally, in 65% -100% relative flow, the fan noise is reduced. Under the design operating condition, total pressure and efficiency of the fan are improved by 6.91% and 0.5%, respectively. This research sheds light on the considering of comprehensive effect of impeller structrual parameters on fan performance, and a new impeller can be designed to satisfy the engineering demand such as energy-saving, noise reduction or solving air pressure insufficiency for power plants.

  10. Low-pressure reversible axial fan with straight profile blades and relatively high efficiency

    OpenAIRE

    Spasić Živan T.; Milanović Saša M.; Šušteršič Vanja M.; Nikolić Boban D.

    2012-01-01

    The paper presents the design and operating characteristics of a model of reversible axial fan with only one impeller, whose reversibility is achieved by changing the direction of rotation. The fan is designed for the purpose of providing alternating air circulation in wood dryers in order to reduce the consumption of electricity for the fan and increase energy efficiency of the entire dryer. To satisfy the reversibility of flow, the shape of the blade profile is symmetrical along the l...

  11. Serpentine Diffuser Performance with Emphasis on Future Introduction to a Transonic Fan (Postprint)

    Science.gov (United States)

    2013-01-01

    AFRL-RQ-WP-TP-2014-0168 SERPENTINE DIFFUSER PERFORMANCE WITH EMPHASIS ON FUTURE INTRODUCTION TO A TRANSONIC FAN (POSTPRINT) Chase A...June 2012 – 01 December 2012 4. TITLE AND SUBTITLE SERPENTINE DIFFUSER PERFORMANCE WITH EMPHASIS ON FUTURE INTRODUCTION TO A TRANSONIC FAN...resulting in an overall recovery factor of 0.983. Distortion descriptors are presented and discussed. 15. SUBJECT TERMS diffuser , transonic fan

  12. The deep-lake deposit in the Upper Triassic Yanchang Formation in Ordos Basin, China and its significance for oil-gas accumulation

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    The deep-lake facies of the Yanchang Formation represents a large outflowing lake basin in the Ordos area. Its deposition can be divided into four stages: lake genetic and expanding stage, peak stage, inversion stage and dying stage. All the stages are obviously consistent with the evolution of depositional environment and the paleoclimate in the region. The study indicates that the lake basin has evolution fluctuations from highstand to lowstand for four times in its evolution history, and the deposition center of the lake has not obviously moved, staying along the Huachi-Yijun belt. The deep lake sedimentary system mainly consists of deep water deltas and turbidite fans during the entire evolution course of the lake basin in the Late Triassic. The former mainly developed on the slope of steep shore of the delta in the early period of the deep-water expansion and gradually experienced a big shift from deep-water deltas to shallow-water platform delta. And the latter appeared almost in all the above stages and had two types of turbidite fans, slope-moving turbidite fans and slump turbidite fans. The slope-moving turbidite fans have relatively complete facies belts overlapping one another vertically and consist of the slope channel of inter fans, the turbidite channel, inter turbidite channel and turbidite channel front of middle fans and outer fans (or lakebottom plain). However, the slide-moving turbidity fans are formed in the deep lake with their microfacies difficult to be distinguished, and only the center microfacies and edge microfacies can be determined. The two types of the turbidity fans are similarly distributing in the near-root-slope and far-root-slope regions. The deep-lake deposition governs the distribution of the hydrocarbon and reservoir, while the slope-moving turbidite fans are excellent reservoirs for oil-gas exploration due to their great thickness, widespread distribution and accumulation properties.

  13. Petroleum Oils

    Science.gov (United States)

    Different types of crude oil and refined product, of all different chemical compositions, have distinct physical properties. These properties affect the way oil spreads and breaks down, its hazard to marine and human life, and the likelihood of threat.

  14. Oil spills

    National Research Council Canada - National Science Library

    Moghissi, A.A

    1980-01-01

    Contents: Oil spills on land as potential sources of groundwater contamination / J.J. Duffy, E. Peake and M.F. Mohtadi -- Ecological effects of experimental oil spills in eastern coastal plain estuaries...

  15. Submarine-fan facies associations of the Eocene Butano Sandstone, Santa Cruz mountains, California

    Science.gov (United States)

    Nilsen, Tor H.

    1984-06-01

    The Eocene Butano Sandstone was deposited as a submarine fan in a relatively small, partly restricted basin in a borderland setting. It is possibly as thick as 3000 m and was derived from erosion of nearly Mesozoic granitic and older metamorphic rocks located to the south. Deposition was at lower bathyal to abyssal water depths. The original fan may have been 120-to 160-km long and 80-km wide. Outcrops of submarine-canyon, innerfan, middle-fan, and outer-fan facies associations indicate that the depositional model of Mutti and Ricci Lucchi can be used to describe the Butano Sandstone.

  16. An experimental investigation of two 15 percent-scale wind tunnel fan-blade designs

    Science.gov (United States)

    Signor, David B.

    1988-01-01

    An experimental 3-D investigation of two fan-blade designs was conducted. The fan blades tested were 15 percent-scale models of blades to be used in the fan drive of the National Full-Scale Aerodynamic Complex at NASA Ames Research Center. NACA 65- and modified NACA 65-series sections incorporated increased thickness on the upper surface, between the leading edge and the one-half-chord position. Twist and taper were the same for both blade designs. The fan blades with modified 65-series sections were found to have an increased stall margin when they were compared with the unmodified blades.

  17. Two-dimensional model of a slow-mode expansion fan at Io

    Science.gov (United States)

    Krisko, P. H.; Hill, T. W.

    1991-01-01

    A 2D model for the standing slow-mode expansion fan that is expected to exist downstream of the Jovian moon Io is developed. The leading edge of the expansion fan makes an angle of 45 deg with the upstream magnetic field direction, and the fan width is about 114 deg. The plasma flow returns to its upstream direction by way of a slow-mode shock behind Io where the MHD parameters return asymptotically to their upstream conditions. The magnetic field perturbation within the fan is much smaller than that associated with the Alfven wing, which lies farther upstream.

  18. Numerical and experimental study on aerodynamic performance of small axial flow fan with splitter blades

    Science.gov (United States)

    Zhu, Lifu; Jin, Yingzi; Li, Yi; Jin, Yuzhen; Wang, Yanping; Zhang, Li

    2013-08-01

    To improve the aerodynamic performance of small axial flow fan, in this paper the design of a small axial flow fan with splitter blades is studied. The RNG k-ɛ turbulence model and SIMPLE algorithm were applied to the steady simulation calculation of the flow field, and its result was used as the initial field of the large eddy simulation to calculate the unsteady pressure field. The FW-H noise model was adopted to predict aerodynamic noise in the six monitoring points. Fast Fourier transform algorithm was applied to process the pressure signal. Experiment of noise testing was done to further investigate the aerodynamic noise of fans. And then the results obtained from the numerical simulation and experiment were described and analyzed. The results show that the static characteristics of small axial fan with splitter blades are similar with the prototype fan, and the static characteristics are improved within a certain range of flux. The power spectral density at the six monitoring points of small axial flow fan with splitter blades have decreased to some extent. The experimental results show sound pressure level of new fan has reduced in most frequency bands by comparing with prototype fan. The research results will provide a proof for parameter optimization and noise prediction of small axial flow fans with high performance.

  19. Experimental Investigation on Design Enhancement of Axial Fan Using Fixed Guide Vane

    Science.gov (United States)

    Munisamy, K. M.; Govindasamy, R.; Thangaraju, S. K.

    2015-09-01

    Airflow passes through the rotating blade in an axial flow fan will experience a helical flow pattern. This swirling effect leads the system to experience swirl energy losses or pressure drop yet reducing the total efficiency of the fan system. A robust tool to encounter this air spin past the blade is by introducing guide vane to the system. Owing to its importance, a new approach in designing outlet guide vane design for a commercial usage 1250mm diameter axial fan with a 30° pitch angle impeller has been introduced in this paper. A single line metal of proper curvature guide vane design technique has been adopted for this study. By choosing fan total efficiency as a target variable to be improved, the total and static pressure on the design point were set to be constraints. Therefore, the guide vane design was done based on the improvement target on the static pressure in system. The research shows that, with the improvement in static pressure by 29.63% through guide vane installation, the total fan efficiency is increased by 5.12%, thus reduces the fan power by 5.32%. Good agreement were found, that when the fan total efficiency increases, the power consumption of the fan is reduced. Therefore, this new approach of guide vane design can be applied to improve axial fan performance.

  20. Design of a high performance low aerodynamic noise axial flow fan

    OpenAIRE

    2007-01-01

    The project starts with a description of the main sources of noise in an axial flow fan for concluding that the thing we should avoid is the trailing edge noise. After that the formulas for designing a fan and an aerodynamics background are presented. Once we get the results of these formulas a low noise optimization is carried on for leading us to a table of results where the main characteristics of design for our fan are obtained. After these tables the design of the fan is obtained with Pr...

  1. Noise reduction for centrifugal fan with non-isometric forward-swept blade impeller

    Institute of Scientific and Technical Information of China (English)

    Jianfeng MA; Datong QI; Yijun MAO

    2008-01-01

    To reduce the noise of the T9-19No.4A centri-fugal fan, whose impeller has equidistant forward-swept blades, two new impellers with different blade spacing were designed and an experimental study was conducted. Both the fan's aerodynamic performance and noise were measured when the two redesigned impellers were com-pared with the original ones. The test results are discussed in detail and the effect of the noise reduction method for a centrifugal fan using impellers with non-isometric for-ward-swept blades was analyzed, which can serve as a reference for researches on reduction of fan noise.

  2. Football fan aggression: the importance of low Basal cortisol and a fair referee.

    Directory of Open Access Journals (Sweden)

    Leander van der Meij

    Full Text Available Fan aggression in football (soccer is a societal problem that affects many countries worldwide. However, to date, most studies use an epidemiological or survey approach to explain football fan aggression. This study used a controlled laboratory study to advance a model of predictors for fan aggression. To do so, football fans (n = 74 saw a match summary in which their favorite team lost against their most important rival. Next, we measured levels of aggression with the hot sauce paradigm, in which fans were given the opportunity to administer a sample of hot sauce that a rival football supporter had to consume. To investigate if media exposure had the ability to reduce aggression, before the match fans saw a video in which fans of the rival team commented in a neutral, negative, or positive manner on their favorite team. Results showed that the media exposure did not affect aggression. However, participants displayed high levels of aggression and anger after having watched the match. Also, aggression was higher in fans with lower basal cortisol levels, which suggests that part of the aggression displayed was proactive and related to anti-social behavior. Furthermore, aggression was higher when the referee was blamed and aggression was lower when the performance of the participants' favorite team was blamed for the match result. These results indicate that aggression increased when the match result was perceived as unfair. Interventions that aim to reduce football fan aggression should give special attention to the perceived fairness of the match result.

  3. Football fan aggression: the importance of low Basal cortisol and a fair referee.

    Science.gov (United States)

    van der Meij, Leander; Klauke, Fabian; Moore, Hannah L; Ludwig, Yannick S; Almela, Mercedes; van Lange, Paul A M

    2015-01-01

    Fan aggression in football (soccer) is a societal problem that affects many countries worldwide. However, to date, most studies use an epidemiological or survey approach to explain football fan aggression. This study used a controlled laboratory study to advance a model of predictors for fan aggression. To do so, football fans (n = 74) saw a match summary in which their favorite team lost against their most important rival. Next, we measured levels of aggression with the hot sauce paradigm, in which fans were given the opportunity to administer a sample of hot sauce that a rival football supporter had to consume. To investigate if media exposure had the ability to reduce aggression, before the match fans saw a video in which fans of the rival team commented in a neutral, negative, or positive manner on their favorite team. Results showed that the media exposure did not affect aggression. However, participants displayed high levels of aggression and anger after having watched the match. Also, aggression was higher in fans with lower basal cortisol levels, which suggests that part of the aggression displayed was proactive and related to anti-social behavior. Furthermore, aggression was higher when the referee was blamed and aggression was lower when the performance of the participants' favorite team was blamed for the match result. These results indicate that aggression increased when the match result was perceived as unfair. Interventions that aim to reduce football fan aggression should give special attention to the perceived fairness of the match result.

  4. Axial Fan Blade Vibration Assessment under Inlet Cross-Flow Conditions Using Laser Scanning Vibrometry

    Directory of Open Access Journals (Sweden)

    Till Heinemann

    2017-08-01

    Full Text Available In thermal power plants equipped with air-cooled condensers (ACCs, axial cooling fans operate under the influence of ambient flow fields. Under inlet cross-flow conditions, the resultant asymmetric flow field is known to introduce additional harmonic forces to the fan blades. This effect has previously only been studied numerically or by using blade-mounted strain gauges. For this study, laser scanning vibrometry (LSV was used to assess fan blade vibration under inlet cross-flow conditions in an adapted fan test rig inside a wind tunnel test section. Two co-rotating laser beams scanned a low-pressure axial fan, resulting in spectral, phase-resolved surface vibration patterns of the fan blades. Two distinct operating points with flow coefficients of 0.17 and 0.28 were examined, with and without inlet cross-flow influence. While almost identical fan vibration patterns were found for both reference operating points, the overall blade vibration increased by 100% at the low fan flow rate as a result of cross-flow, and by 20% at the high fan flow rate. While numerically predicted natural frequency modes could be confirmed from experimental data as minor peaks in the vibration amplitude spectrum, they were not excited significantly by cross-flow. Instead, primarily higher rotation-rate harmonics were amplified; that is, a synchronous blade-tip flapping was strongly excited at the blade-pass frequency.

  5. Oil Shale

    Science.gov (United States)

    Birdwell, Justin E.

    2017-01-01

    Oil shales are fine-grained sedimentary rocks formed in many different depositional environments (terrestrial, lacustrine, marine) containing large quantities of thermally immature organic matter in the forms of kerogen and bitumen. If defined from an economic standpoint, a rock containing a sufficient concentration of oil-prone kerogen to generate economic quantities of synthetic crude oil upon heating to high temperatures (350–600 °C) in the absence of oxygen (pyrolysis) can be considered an oil shale.

  6. Atom Skimmers and Atom Lasers Utilizing Them

    Science.gov (United States)

    Hulet, Randall; Tollett, Jeff; Franke, Kurt; Moss, Steve; Sackett, Charles; Gerton, Jordan; Ghaffari, Bita; McAlexander, W.; Strecker, K.; Homan, D.

    2005-01-01

    Atom skimmers are devices that act as low-pass velocity filters for atoms in thermal atomic beams. An atom skimmer operating in conjunction with a suitable thermal atomic-beam source (e.g., an oven in which cesium is heated) can serve as a source of slow atoms for a magneto-optical trap or other apparatus in an atomic-physics experiment. Phenomena that are studied in such apparatuses include Bose-Einstein condensation of atomic gases, spectra of trapped atoms, and collisions of slowly moving atoms. An atom skimmer includes a curved, low-thermal-conduction tube that leads from the outlet of a thermal atomic-beam source to the inlet of a magneto-optical trap or other device in which the selected low-velocity atoms are to be used. Permanent rare-earth magnets are placed around the tube in a yoke of high-magnetic-permeability material to establish a quadrupole or octupole magnetic field leading from the source to the trap. The atoms are attracted to the locus of minimum magnetic-field intensity in the middle of the tube, and the gradient of the magnetic field provides centripetal force that guides the atoms around the curve along the axis of the tube. The threshold velocity for guiding is dictated by the gradient of the magnetic field and the radius of curvature of the tube. Atoms moving at lesser velocities are successfully guided; faster atoms strike the tube wall and are lost from the beam.

  7. Mineral oils

    Science.gov (United States)

    Furby, N. W.

    1973-01-01

    The characteristics of lubricants made from mineral oils are discussed. Types and compositions of base stocks are reviewed and the product demands and compositions of typical products are outlined. Processes for commercial production of mineral oils are examined. Tables of data are included to show examples of product types and requirements. A chemical analysis of three types of mineral oils is reported.

  8. Oil biodegradation

    NARCIS (Netherlands)

    Rahsepar, Shokouhalsadat; Langenhoff, Alette A.M.; Smit, Martijn P.J.; Eenennaam, van Justine S.; Murk, Tinka; Rijnaarts, Huub H.M.

    2017-01-01

    During the Deepwater Horizon (DwH) oil spill, interactions between oil, clay particles and marine snow lead to the formation of aggregates. Interactions between these components play an important, but yet not well understood, role in biodegradation of oil in the ocean water. The aim of this study

  9. Influence of Coanda surface curvature on performance of bladeless fan

    Science.gov (United States)

    Li, Guoqi; Hu, Yongjun; Jin, Yingzi; Setoguchi, Toshiaki; Kim, Heuy Dong

    2014-10-01

    The unique Coanda surface has a great influence on the performance of bladeless fan. However, there is few studies to explain the relationship between the performance and Coanda surface curvature at present. In order to gain a qualitative understanding of effect of the curvature on the performance of bladeless fan, numerical studies are performed in this paper. Firstly, three-dimensional numerical simulation is done by Fluent software. For the purpose to obtain detailed information of the flow field around the Coanda surface, two-dimensional numerical simulation is also conducted. Five types of Coanda surfaces with different curvature are designed, and the flow behaviour and the performance of them are analyzed and compared with those of the prototype. The analysis indicates that the curvature of Coanda surface is strongly related to blowing performance, It is found that there is an optimal curvature of Coanda surfaces among the studied models. Simulation result shows that there is a special low pressure region. With increasing curvature in Y direction, several low pressure regions gradually enlarged, then begin to merge slowly, and finally form a large area of low pressure. From the analyses of streamlines and velocity angle, it is found that the magnitude of the curvature affects the flow direction and reasonable curvature can induce fluid flow close to the wall. Thus, it leads to that the curvature of the streamlines is consistent with that of Coanda surface. Meanwhile, it also causes the fluid movement towards the most suitable direction. This study will provide useful information to performance improvements of bladeless fans.

  10. Fan beam image reconstruction with generalized Fourier slice theorem.

    Science.gov (United States)

    Zhao, Shuangren; Yang, Kang; Yang, Kevin

    2014-01-01

    For parallel beam geometry the Fourier reconstruction works via the Fourier slice theorem (or central slice theorem, projection slice theorem). For fan beam situation, Fourier slice can be extended to a generalized Fourier slice theorem (GFST) for fan-beam image reconstruction. We have briefly introduced this method in a conference. This paper reintroduces the GFST method for fan beam geometry in details. The GFST method can be described as following: the Fourier plane is filled by adding up the contributions from all fanbeam projections individually; thereby the values in the Fourier plane are directly calculated for Cartesian coordinates such avoiding the interpolation from polar to Cartesian coordinates in the Fourier domain; inverse fast Fourier transform is applied to the image in Fourier plane and leads to a reconstructed image in spacial domain. The reconstructed image is compared between the result of the GFST method and the result from the filtered backprojection (FBP) method. The major differences of the GFST and the FBP methods are: (1) The interpolation process are at different data sets. The interpolation of the GFST method is at projection data. The interpolation of the FBP method is at filtered projection data. (2) The filtering process are done in different places. The filtering process of the GFST is at Fourier domain. The filtering process of the FBP method is the ramp filter which is done at projections. The resolution of ramp filter is variable with different location but the filter in the Fourier domain lead to resolution invariable with location. One advantage of the GFST method over the FBP method is in short scan situation, an exact solution can be obtained with the GFST method, but it can not be obtained with the FBP method. The calculation of both the GFST and the FBP methods are at O(N^3), where N is the number of pixel in one dimension.

  11. Analysis of high velocity impact on hybrid composite fan blades

    Science.gov (United States)

    Chamis, C. C.; Sinclair, J. H.

    1979-01-01

    This paper describes recent developments in the analysis of high velocity impact of composite blades using a computerized capability which consists of coupling a composites mechanics code with the direct-time integration features of NASTRAN. The application of the capability to determine the linear dynamic response of an intraply hybrid composite aircraft engine fan blade is described in detail. The predicted results agree with measured data. The results also show that the impact stresses reach sufficiently high magnitudes to cause failures in the impact region at early times of the impact event.

  12. Debris flow hazards and risks on Cheekye Fan, British Columbia

    Science.gov (United States)

    Jakob, M.

    2009-04-01

    Natural hazard and risk assessments hinge fundamentally on a detailed understanding of the relationship between frequency and magnitude of the hazardous process under investigation. When information is sought from the deep past (i.e. several thousand years), continuous event records do not exist and the researcher has to rely on proxy data to develop the F-M model. Such work is often prohibitively expensive and few well researched examples for mass movement are available worldwide. Cheekye fan is a desirable location for land development and has a depth and breadth of previous research unprecedented on any debris flow fan in Canada. We pursued two principal strains of research to formulate a reliable frequency-magnitude relationship. The first focuses on stratigraphic analyses combined with radiometric dating and dendrochronology to reconstruct a comprehensive picture of Holocene debris flow activity. The second approach examines hydrological limitations of rock avalanche evolution into debris flows through either entrainment of saturated sediments or by failure of a landslide-generated dam and upstream impoundment. We thus hypothesize that debris flows from Cheekye River can be separated into two quasi homogenous populations: those that are typically triggered by relatively small debris avalanches, slumps or rock falls or simply by progressive bulking of in-stream erodible sediments; and those that are thought to result from transformation of rock avalanches. Our work suggests that debris flows exceeding some 3 million cubic metres in volume are unlikely to reach Cheekye fan due to limited water available to fully fluidize a rock avalanche. This analysis has also demonstrated that in order to arrive at reasonable estimates for the frequency and magnitude of debris flows on a complex alluvial fan, significant multidisciplinary efforts are required. As a second step in the analysis, we model the design debris flow using a two-dimensional debris flow runout model

  13. Development of an Ultralight with a Ducted Fan

    Directory of Open Access Journals (Sweden)

    Jiří Brabec

    2012-01-01

    Full Text Available This paper introduces the UL-39 project, an ultralight aircraft with a ducted fan, and some of the problems that have arisen in the course of its development. Several problems with the design of a non-traditional aircraft of this kind are mentioned, e.g. the design of the airframe, and the design of the propulsion unit. The paper describes the specific procedure for determining the basic thrust characteristics of this unusual aircraft concept, and also the experimental determination of these characteristics. Further options for applying the experience gained during the work, and the futurefocus of work on these issues, are outlined at the end of the paper.

  14. Experimental Investigation of Stator Flow in Diagonal Flow Fan

    Institute of Scientific and Technical Information of China (English)

    Jie Wang; Yoichi Kinoue; Norimasa Shiomi; Toshiaki Setoguchi; Kenji Kaneko; Yingzi Jin

    2008-01-01

    perimental investigations were conducted for the internal flow of the stator of the diagonal flow fan. Comer separation near the hub surface and the suction surface of the stator blade are focused on. At the design flow rate, the values of the axial velocity and the total pressure at stator outlet decrease near the suction surface at around the hub surface by the influence of the comer wall. At low flow rate of 80-90 % of the design flow rate, the comer separation between the suction surface and the hub surface can be found, which become widely spread at 80 % of the design flow rate.

  15. Experimental investigation of stator flow in diagonal flow fan

    Science.gov (United States)

    Wang, Jie; Kinoue, Yoichi; Shiomi, Norimasa; Setoguchi, Toshiaki; Kaneko, Kenji; Jin, Yingzi

    2008-12-01

    Experimental investigations were conducted for the internal flow of the stator of the diagonal flow fan. Corner separation near the hub surface and the suction surface of the stator blade are focused on. At the design flow rate, the values of the axial velocity and the total pressure at stator outlet decrease near the suction surface at around the hub surface by the influence of the corner wall. At low flow rate of 80-90 % of the design flow rate, the corner separation between the suction surface and the hub surface can be found, which become widely spread at 80 % of the design flow rate.

  16. Numerical evaluation of tandem rotor for highly loaded transonic fan

    Institute of Scientific and Technical Information of China (English)

    ZHAO Bin; LIU Bao-jie

    2011-01-01

    Transonic tandem rotor was designed for highly loaded fan at a corrected tip speed of 381 m/s and another conventional rotor was designed as a baseline to evaluate the loading superiority of tandem rotor with three-dimensional (3-D) numerical simulation. The aft blade solidity and its impact on total loading level were studied in depth. The result indicates that tandem rotor has potential to achieve higher loading level and attain favorable aerodynamic performance in a wide range of loading coefficient 0. 55 ~ 0.68, comparing with the conventional rotor which produced a total pressure ratio of 2.0 and loading coefficient of 0. 42.

  17. Zero-Divisor Semigroups of Fan-Shaped Graph

    Institute of Scientific and Technical Information of China (English)

    Ke ZHOU; Hua Dong SU

    2011-01-01

    Let Pn be a path graph with n vertices,and let Fn =Pn U {c},where c is adjacent to all vertices of Pn.The resulting graph is called a fan-shaped graph.The corresponding zero-divisor semigroups have been completely determined by Tang et al.for n =2,3,4 and by Wu et al.for n ≥ 6,respectively.In this paper,we study the case for n =5,and give all the corresponding zero-divisor semigroups of Fn.

  18. Two-Stage Fan I: Aerodynamic and Mechanical Design

    Science.gov (United States)

    Messenger, H. E.; Kennedy, E. E.

    1972-01-01

    A two-stage, highly-loaded fan was designed to deliver an overall pressure ratio of 2.8 with an adiabatic efficiency of 83.9 percent. At the first rotor inlet, design flow per unit annulus area is 42 lbm/sec/sq ft (205 kg/sec/sq m), hub/tip ratio is 0.4 with a tip diameter of 31 inches (0.787 m), and design tip speed is 1450 ft/sec (441.96 m/sec). Other features include use of multiple-circular-arc airfoils, resettable stators, and split casings over the rotor tip sections for casing treatment tests.

  19. Atomic magnetometer

    Science.gov (United States)

    Schwindt, Peter [Albuquerque, NM; Johnson, Cort N [Albuquerque, NM

    2012-07-03

    An atomic magnetometer is disclosed which uses a pump light beam at a D1 or D2 transition of an alkali metal vapor to magnetically polarize the vapor in a heated cell, and a probe light beam at a different D2 or D1 transition to sense the magnetic field via a polarization rotation of the probe light beam. The pump and probe light beams are both directed along substantially the same optical path through an optical waveplate and through the heated cell to an optical filter which blocks the pump light beam while transmitting the probe light beam to one or more photodetectors which generate electrical signals to sense the magnetic field. The optical waveplate functions as a quarter waveplate to circularly polarize the pump light beam, and as a half waveplate to maintain the probe light beam linearly polarized.

  20. Surface processes on a mud-dominated Mars analogue alluvial fan, Atacama Desert, northern Chile

    Science.gov (United States)

    Hobley, D. E.; Howard, A. D.; Morgan, A. M.; Matsubara, Y.; Moore, J. M.; Parsons, R.; Williams, R. M.; Burr, D. M.; Hayes, A. G.; Dietrich, W.

    2012-12-01

    We characterize surface processes on highly unusual terrestrial alluvial fans, which we interpret as a strong analogue for large fans on Mars. The Mars fans date to post-Noachian periods when the martian climate was dominated by cold, hyperarid conditions. Some of the martian fans are differentially eroded to leave their distributary channels in positive relief. This inversion, along with the lack of boulders visible on most fan surfaces, reveals that the dominant grain size of the fans is fine enough for the overbank deposits to be stripped by wind. Degradation, image resolution, and lack of ground truthing all act to obscure the nature of the past flow processes. The fans in the Pampa de Tamarugal of the Atacama Desert of northern Chile are excellent potential Mars analogues for a number of reasons: 1. Hyperaridity, with ~2 mm/y rainfall over the fans themselves, resulting in 2. very little vegetation, 3. no fluvial erosion on the fans themselves, and 4. wind-driven erosion of the fan surfaces; 5. equivalent fan scale (tens of km); 6. similar fan gradient (low); 7. low channel branching density; 8. runoff fed from adjacent, much steeper terrain receiving more precipitation (~500 km2 drainages receiving 0.1-1 m/y precipitation in the High Andes, crater walls and interpreted orographic effects on Mars). Both the modern channels and the preserved stratigraphy are dominated by debris flow-like sheetflow mud deposits. Channels are leveed by concrete-like mass-supported deposits of granules and sand suspended in a silt and clay matrix, often overtopping the channel margins and forming up to 150 m wide levees and km-length sheet flows. This leveeing strongly constrains the aggrading channel, which is typically dominated by better sorted and imbricated fluvial deposits. We infer that the wetter tail of mudlfows sorts the deposits, keeping the central channel unblocked by mud. Relatively few channels are active at any time, but aggradation triggers occasional avulsions

  1. Demonstration of Intelligent Control and Fan Improvements in Computer Room Air Handlers

    Energy Technology Data Exchange (ETDEWEB)

    Coles, Henry [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States). Environmental Energy Technologies Division; Greenberg, Steve [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States). Environmental Energy Technologies Division; Vita, Corinne [Vigilent, Oakland, CA (United States)

    2012-11-30

    This report documents a demonstration of the energy-efficiency improvement provided by a new control system for computer room air handling devices. It also analyzes measured and reported air handling device fan power associated with changing the fan type. A 135,000 square foot commercial data center was used for the demonstration. All air handling units were upgraded with improved efficiency fans, and a control system that automatically adjusts the fan speed for the air handling units was added. Power measurements were collected for a baseline and for a period with the fan speed control system active. Changing the fan type resulted in a savings of 47 percent of energy used by the air handling equipment and associated chiller plant energy needed to cool the air handlers themselves. The addition of the fan speed control resulted in an additional 37 percent savings in the same two categories. The combined savings for the two improvements for the same categories was 66 percent compared to the data center fitted with the original fans without a control system. The energy use reduction provided by the complete air handling device improvement program for the whole data center site is estimated to be 2.9 million kilowatt hours per year—an overall data center site savings of 8.0 percent. The reduced electrical energy use at the site provides a 1.9 million pound yearly reduction of carbon dioxide emissions. This demonstration showed that fan upgrades and a control system addition provide cost-effective improvements for data centers, with a payback reported to be under two years without utility incentives. In addition to the control system providing energy savings, the data collection and visual analysis capabilities provided immediate and long-term benefits. It is recommended that data center operators consider investing in fan upgrades and/or adding fan speed control for computer room air handlers.

  2. Controls on modern tributary-junction alluvial fan occurrence and morphology: High Atlas Mountains, Morocco

    Science.gov (United States)

    Stokes, Martin; Mather, Anne E.

    2015-11-01

    Modern tributary-junction alluvial fans (cone-shaped depositional landforms formed in confined valley settings) were analysed from a 20-km-long reach of the Dades River in the distal part of the fold-thrust belt region in the south-central High Atlas Mountains of Morocco. Here, a deeply dissected network of ephemeral tributary streams and a perennial trunk drainage characterised by an arid mountain desert climate are configured onto a folded and thrust faulted Mesozoic sedimentary sequence. Out of 186 tributary streams, only 29 (16%) generated alluvial fans at their tributary junctions. The fan-generating catchments possess higher relief, longer lengths, lower gradients, and larger areas than nonfan-generating catchments. Whilst geologically, fan-generating catchments are underlain by folded/steeply dipping weak bedrock conducive to high sediment yield. Tributary-junction fans are built from debris flow or fluvial processes into open or confined canyon trunk valley settings. The proximity of the perennial trunk drainage combined with the valley morphology produces lobate or foreshortened trimmed fan forms. Analysis of fan (area, gradient, process), catchment (area, relief, length, gradient), and tributary valley (width) variables reveals weak morphometric relationships, highlighted by residual plots that show dominance of smaller and lower gradient than expected fan forms. These morphometric relationships can be explained by interplay between the catchment and trunk drainage geology, morphology, climate, and flood regime that are combined into a conceptual 'build and reset' model. Ephemeral tributary-junction fans develop progressively during annual localised winter-spring storm events, attempting to build towards a morphological equilibrium. However, the fans never reach an equilibrium morphological form as they are reset by rare (> 10 year) large floods along the River Dades that are linked to regional incursions of Atlantic low pressure troughs. The model

  3. High Atom Number in Microsized Atom Traps

    Science.gov (United States)

    2015-12-14

    Final Performance Report on ONR Grant N00014-12-1-0608 High atom number in microsized atom traps for the period 15 May 2012 through 14 September...TYPE Final Technical Report 3. DATES COVERED (From - To) 05/15/2012-09/14/2012 4. TITLE AND SUBTITLE High atom number in microsized atom traps...forces for implementing a small-footprint, large-number atom -chip instrument. Bichromatic forces rely on absorption and stimulated emission to produce

  4. Detecting Neutral Atoms on an Atom Chip

    OpenAIRE

    Wilzbach, M.; Haase, A.; Schwarz, M; Heine, D.; Wicker, K.; Liu, X; Brenner, K. -H.; Groth, S.; Fernholz, Th.; Hessmo, B.; Schmiedmayer, J.

    2006-01-01

    Detecting single atoms (qubits) is a key requirement for implementing quantum information processing on an atom chip. The detector should ideally be integrated on the chip. Here we present and compare different methods capable of detecting neutral atoms on an atom chip. After a short introduction to fluorescence and absorption detection we discuss cavity enhanced detection of single atoms. In particular we concentrate on optical fiber based detectors such as fiber cavities and tapered fiber d...

  5. Rapid delineation of alluvial fans using IfSAR-derived DEM for selected provinces in the Philippines

    Science.gov (United States)

    Ortiz, Iris Jill; Aquino, Dakila; Norini, Gianluca; Narod Eco, Rodrigo; Mahar Lagmay, Alfredo

    2015-04-01

    Alluvial fans are fan-shaped geomorphic features formed when sediments from a watershed are transported and deposited downstream via tributaries flowing out from the sudden break of a slope. Hazards usually associated with alluvial fans are flooding and debris flows. In this study, we used an Interferometric Synthetic Aperture Radar-derived digital elevation model of Pangasinan and Nueva Ecija Provinces in the Philippines to identify and delineate alluvial fans. Primary parameters considered include the geomorphic characteristics of the catchment area, stream network and slopes ranging from 0.11 to 8 degrees. Using this method, 12 alluvial fans were identified in Pangasinan and 16 in Nueva Ecija with areas ranging from 0.35 to 80 sq. km. The largest fan identified is the Mangatarem-Aguilar fan in Pangaisnan with a total area of 80.87 sq km while the Gabaldon fan in Nueva Ecija with total area of 48.11 sq km. We observed from the results that some alluvial fans have multiple feeder streams, and others have overlapping lateral extents with adjacent fans. These overlapping fans are called bajadas. In addition, the general location of fans and their apices in the two provinces appear to coincide with segments of the Philippines Fault System. There are about people 1.4 million living within these alluvial fans. Mapping and characterizing and identifying their associated hazards is crucial in the disaster preparedness efforts of the exposed population.

  6. Effects of perforation number of blade on aerodynamic performance of dual-rotor small axial flow fans

    Science.gov (United States)

    Hu, Yongjun; Wang, Yanping; Li, Guoqi; Jin, Yingzi; Setoguchi, Toshiaki; Kim, Heuy Dong

    2015-04-01

    Compared with single rotor small axial flow fans, dual-rotor small axial flow fans is better regarding the static characteristics. But the aerodynamic noise of dual-rotor small axial flow fans is worse than that of single rotor small axial flow fans. In order to improve aerodynamic noise of dual-rotor small axial flow fans, the pre-stage blades with different perforation numbers are designed in this research. The RANS equations and the standard k-ɛ turbulence model as well as the FW-H noise model are used to simulate the flow field within the fan. Then, the aerodynamic performance of the fans with different perforation number is compared and analyzed. The results show that: (1) Compared to the prototype fan, the noise of fans with perforation blades is reduced. Additionally, the noise of the fans decreases with the increase of the number of perforations. (2) The vorticity value in the trailing edge of the pre-stage blades of perforated fans is reduced. It is found that the vorticity value in the trailing edge of the pre-stage blades decreases with the increase of the number of perforations. (3) Compared to the prototype fan, the total pressure rising and efficiency of the fans with perforation blades drop slightly.

  7. Intermittent Flow Regimes in a Transonic Fan Airfoil Cascade

    Science.gov (United States)

    Lepicovsky, J.; McFarland, E. R.; Chima, R. V.; Capece, V. R.; Hayden, J.

    2002-01-01

    A study was conducted in the NASA Glenn Research Center linear cascade on the intermittent flow on the suction surface of an airfoil section from the tip region of a modern low aspect ratio fan blade. Experimental results revealed that, at a large incidence angle, a range of transonic inlet Mach numbers exist where the leading-edge shock-wave pattern was unstable. Flush mounted high frequency response pressure transducers indicated large local jumps in the pressure in the leading edge area, which generates large intermittent loading on the blade leading edge. These measurements suggest that for an inlet Mach number between 0.9 and 1.0 the flow is bi-stable, randomly switching between subsonic and supersonic flows. Hence, it appears that the change in overall flow conditions in the transonic region is based on the frequency of switching between two stable flow states rather than on the continuous increase of the flow velocity. To date, this flow behavior has only been observed in a linear transonic cascade. Further research is necessary to confirm this phenomenon occurs in actual transonic fans and is not the byproduct of an endwall restricted linear cascade.

  8. Piezoelectric Vibration Damping Study for Rotating Composite Fan Blades

    Science.gov (United States)

    Min, James B.; Duffy, Kirsten P.; Choi, Benjamin B.; Provenza, Andrew J.; Kray, Nicholas

    2012-01-01

    Resonant vibrations of aircraft engine blades cause blade fatigue problems in engines, which can lead to thicker and aerodynamically lower performing blade designs, increasing engine weight, fuel burn, and maintenance costs. In order to mitigate undesirable blade vibration levels, active piezoelectric vibration control has been investigated, potentially enabling thinner blade designs for higher performing blades and minimizing blade fatigue problems. While the piezoelectric damping idea has been investigated by other researchers over the years, very little study has been done including rotational effects. The present study attempts to fill this void. The particular objectives of this study were: (a) to develop and analyze a multiphysics piezoelectric finite element composite blade model for harmonic forced vibration response analysis coupled with a tuned RLC circuit for rotating engine blade conditions, (b) to validate a numerical model with experimental test data, and (c) to achieve a cost-effective numerical modeling capability which enables simulation of rotating blades within the NASA Glenn Research Center (GRC) Dynamic Spin Rig Facility. A numerical and experimental study for rotating piezoelectric composite subscale fan blades was performed. It was also proved that the proposed numerical method is feasible and effective when applied to the rotating blade base excitation model. The experimental test and multiphysics finite element modeling technique described in this paper show that piezoelectric vibration damping can significantly reduce vibrations of aircraft engine composite fan blades.

  9. Fan Noise Source Diagnostic Test: Tone Modal Structure Results

    Science.gov (United States)

    Heidelberg, Laurence J.

    2002-01-01

    This investigation is part of a test series that was extremely comprehensive and included aerodynamic and acoustic testing of a fan stage using two different fan rotors and three different stator designs. The test series is known as the Source Diagnostic Test (SDT) and was conducted by NASA Glenn as part of the Advanced Subsonic Technology (AST) Noise Reduction Program. Tone mode measurements of one of the rotors with three different stators were made. The stator designs involve changes in vane count and sweep at constant solidity. The results of both inlet and exhaust tone mode measurements are presented in terms of mode power for both circumferential and radial mode orders. The results show benefits of vane sweep to be large, up to 13 dB in total tone power. At many conditions, the increase in power due to cutting on the rotor/stator interaction is more than offset by vane sweep. The rotor locked mode is shown as an important contributor to tone power when the blade tip speed is near and above Mach one. This is most evident in the inlet when the direct rotor field starts to cut on.

  10. Fan Noise Source Diagnostic Test: LDV Measured Flow Field Results

    Science.gov (United States)

    Podboy, Gary C.; Krupar, Martin J.; Hughes, Christopher E.; Woodward, Richard P.

    2003-01-01

    Results are presented of an experiment conducted to investigate potential sources of noise in the flow developed by two 22-in. diameter turbofan models. The R4 and M5 rotors that were tested were designed to operate at nominal take-off speeds of 12,657 and 14,064 RPMC, respectively. Both fans were tested with a common set of swept stators installed downstream of the rotors. Detailed measurements of the flows generated by the two were made using a laser Doppler velocimeter system. The wake flows generated by the two rotors are illustrated through a series of contour plots. These show that the two wake flows are quite different, especially in the tip region. These data are used to explain some of the differences in the rotor/stator interaction noise generated by the two fan stages. In addition to these wake data, measurements were also made in the R4 rotor blade passages. These results illustrate the tip flow development within the blade passages, its migration downstream, and (at high rotor speeds) its merging with the blade wake of the adjacent (following) blade. Data also depict the variation of this tip flow with tip clearance. Data obtained within the rotor blade passages at high rotational speeds illustrate the variation of the mean shock position across the different blade passages.

  11. Experimental Investigation of a High Pressure Ratio Aspirated Fan Stage

    Science.gov (United States)

    Merchant, Ali; Kerrebrock, Jack L.; Adamczyk, John J.; Braunscheidel, Edward

    2004-01-01

    The experimental investigation of an aspirated fan stage designed to achieve a pressure ratio of 3.4:1 at 1500 ft/sec is presented in this paper. The low-energy viscous flow is aspirated from diffusion-limiting locations on the blades and flowpath surfaces of the stage, enabling a very high pressure ratio to be achieved in a single stage. The fan stage performance was mapped at various operating speeds from choke to stall in a compressor facility at fully simulated engine conditions. The experimentally determined stage performance, in terms of pressure ratio and corresponding inlet mass flow rate, was found to be in good agreement with the three-dimensional viscous computational prediction, and in turn close to the design intent. Stage pressure ratios exceeding 3:1 were achieved at design speed, with an aspiration flow fraction of 3.5 percent of the stage inlet mass flow. The experimental performance of the stage at various operating conditions, including detailed flowfield measurements, are presented and discussed in the context of the computational analyses. The sensitivity of the stage performance and operability to reduced aspiration flow rates at design and off design conditions are also discussed.

  12. Altitude effects on combustion in residential furnaces with fan assist

    Energy Technology Data Exchange (ETDEWEB)

    Arnold, S.; Fleck, B.A.; Ackerman, M.Y.; Dale, J.D.; Wilson, D.J. [Alberta Univ., Edmonton, AB (Canada). Dept. of Mechanical Engineering

    2002-07-01

    Five residential furnaces were tested to determine if altitude has an effect on the performance of modern furnaces equipped with fan assisted flue venting systems. The tests were conducted at 3 altitudes, 50 m, 685 m and 2050 m above sea level at sites in Vancouver, Edmonton, and Fortress Mountain, Alberta. Current furnace derating practices require that furnaces at high altitude have small fuel openings or decreased fuel supply manifold pressures. However, it is possible that modern furnaces with fan driven combustion venting do not have to be derated to the same extent. Propane and natural gas were the fuel sources for the tests. It was confirmed that since most residential systems are designed to operate at 100 per cent excess air, the current derating standard practice is overly conservative. The effects of altitude on carbon monoxide and carbon dioxide levels were also examined, along with burner and igniter operating characteristics, heat exchanger operating temperatures, and blocked-vent shutoff combustion performance. 1 tab., 3 figs.

  13. Jet Engine Fan Blade Containment Using an Alternate Geometry

    Science.gov (United States)

    Carney, K.S.; Pereira, J.M.; Revilock, D.M.; Matheny, P.

    2008-01-01

    With a goal of reducing jet engine weight, simulations of a fan blade containment system with an alternate geometry were tested and analyzed. A projectile simulating a fan blade was shot at two alternate geometry containment case configurations using a gas gun. The first configuration was a flat plate representing a standard case configuration. The second configuration was a flat plate with a radially convex curve section at the impact point. The curved surface was designed to force the blade to deform plastically, dissipating energy before the full impact of the blade is received by the plate. The curved case was able to tolerate a higher impact velocity before failure. The computational model was developed and correlated with the tests and a weight savings assessment was performed. For the particular test configuration used in this study the ballistic impact velocity of the curved plate was approximately 60 m/s (200 ft/s) greater than that of the flat plate. For the computational model to successfully duplicate the test, the very high strain rate behavior of the materials had to be incorporated.

  14. Toric Stacks I: The Theory of Stacky Fans

    CERN Document Server

    Geraschenko, Anton

    2011-01-01

    The purpose of this paper and its sequel (Toric Stacks II) is to introduce and develop a theory of toric stacks which encompasses and extends the notions of toric stacks defined in [Laf02, BCS05, FMN09, Iwa09a, Sat09, Tyo10], as well as classical toric varieties. In this paper, we define a \\emph{toric stack} as a quotient of a toric variety by a subgroup of its torus (we also define a generically stacky version). Any toric stack arises from a combinatorial gadget called a \\emph{stacky fan}. We develop a dictionary between the combinatorics of stacky fans and the geometry of toric stacks, stressing stacky phenomena such as canonical stacks and good moduli space morphisms. We also show that smooth toric stacks carry a moduli interpretation extending the usual moduli interpretations of $\\PP^n$ and $[\\AA^1/\\GG_m]$. Indeed, smooth toric stacks precisely solve moduli problems specified by (generalized) effective Cartier divisors with given linear relations and given intersection relations. Smooth toric stacks there...

  15. Evaluation of Retrofit Variable-Speed Furnace Fan Motors

    Energy Technology Data Exchange (ETDEWEB)

    Aldrich, R. [Consortium for Advanced Residential Buildings (CARB), Norwalk, CT (United States); Williamson, J. [Consortium for Advanced Residential Buildings (CARB), Norwalk, CT (United States)

    2014-01-01

    In conjunction with the New York State Energy Research and Development Authority (NYSERDA) and Proctor Engineering Group, Ltd. (PEG), the Consortium for Advanced Residential Buildings (CARB) has evaluated the Concept 3™ replacement motors for residential furnaces. These brushless, permanent magnet (BPM) motors can use much less electricity than their PSC (permanent split capacitor) predecessors. This evaluation focuses on existing homes in the heating-dominated climate of upstate New York with the goals of characterizing field performance and cost effectiveness. The project includes eight homes in and near Syracuse, NY. Tests and monitoring was performed both before and after fan motors were replaced. Results indicate that BPM replacement motors will be most cost effective in HVAC systems with longer run times and relatively low duct static pressures. More dramatic savings are possible if occupants use the fan-only setting when there is no thermal load. There are millions of cold-climate, U.S. homes that meet these criteria, but the savings in most homes tested in this study were modest.

  16. Cost analysis of composite fan blade manufacturing processes

    Science.gov (United States)

    Stelson, T. S.; Barth, C. F.

    1980-01-01

    The relative manufacturing costs were estimated for large high technology fan blades prepared by advanced composite fabrication methods using seven candidate materials/process systems. These systems were identified as laminated resin matrix composite, filament wound resin matrix composite, superhybrid solid laminate, superhybrid spar/shell, metal matrix composite, metal matrix composite with a spar and shell, and hollow titanium. The costs were calculated utilizing analytical process models and all cost data are presented as normalized relative values where 100 was the cost of a conventionally forged solid titanium fan blade whose geometry corresponded to a size typical of 42 blades per disc. Four costs were calculated for each of the seven candidate systems to relate the variation of cost on blade size. Geometries typical of blade designs at 24, 30, 36 and 42 blades per disc were used. The impact of individual process yield factors on costs was also assessed as well as effects of process parameters, raw materials, labor rates and consumable items.

  17. On-chip grating coupler array on the SOI platform for fan-in/fan-out of multi-core fibers with low insertion loss and crosstalk

    DEFF Research Database (Denmark)

    Ding, Yunhong; Ye, Feihong; Peucheret, Christophe

    2014-01-01

    We design and fabricate a compact multi-core fiber fan-in/fan-out using a fully-etched grating coupler array on the SOI platform. Lowest coupling loss of 6.8 dB with 3 dB bandwidth of 48 nm and crosstalk lower than ×32 dB are demonstrated.......We design and fabricate a compact multi-core fiber fan-in/fan-out using a fully-etched grating coupler array on the SOI platform. Lowest coupling loss of 6.8 dB with 3 dB bandwidth of 48 nm and crosstalk lower than ×32 dB are demonstrated....

  18. Variable scale channel avulsion history using fan architecture and stratigraphy, and sediment provenance of Sutlej-Yamuna fans in northwest Gangetic plains during Late Quaternary

    Science.gov (United States)

    Singh, Ajit; Gupta, Sanjeev; Sinha, Rajiv; Densmore, Alexander; Buylaert, Jan-Pieter; Carter, Andrew; Van-Dijk, Wout M.; Joshi, Suneel; Nayak, Nibedita; Mason, Philippa J.; Kumar, Dewashish; Mondal, Setbandhu; Murray, Andrew; Rai, Shiv P.; Shekhar, Shashank

    2016-04-01

    Channel avulsion during fan development controls distribution and deposition of channel sandbodies and hence alluvial architecture of a fan system. Variable scale spatio-temporal information of fluvial responses to past climate changes is stored in these channel sandbodies. Further these channel sandbodies form fluvial aquifers in alluvial fans and therefore understanding of alluvial architecture and stratigraphy of a fan is crucial for development of groundwater management strategies. In this study we used multiple approaches to map subsurface fluvial aquifer architecture and alluvial stratigraphy, and to estimate sediment provenance using U-Pb dating of detrital zircon grains of Sutlej-Yamuna fan system in northwest India. Satellite imagery based geomorphic mapping shows two large fan system with interfan area. The fan surfaces show presence of major and minor paleochannels. 2D resistivity tomography along several transects across fan surfaces shows distinct layers with contrasting resistivity values. These geo-electric facies corresponds to presence of channel sandbodies beneath surface signature of paleochannels and finer floodplain deposits useful to demarcate lateral extent of subsurface channel sandbodies. A more detailed subsurface stratigraphy using ~50m deep sediment cores and their luminescence ages from across fan surface shows presence of multi-storey sandbodies (MSB) separated by floodplain fines. Within the MSB, individual channel deposits are identified by presence of channel scour surfaces located at coarse sand overlying fine sand layer. Depositional ages of MSB's ranges from ~81 ka (late MIS5) to ~15 ka (MIS2) with major depositional break during MIS3 in parts of the fans. Sediment aggradation rate varies laterally across fan surface as well as vertically down the depth with an average rate of 0.54 mm/year. Fluvial channel persistence for studied time interval (about last 81 ka BP) shows major depositional breaks (and possible incision) at ~41 ka

  19. Autogenic dynamics of alluvial fans in endorheic basins: Outcrop examples and stratigraphic significance

    NARCIS (Netherlands)

    Ventra, D.; Nichols, G.J.

    2014-01-01

    Alluvial fans are relatively simple depositional systems, due to the direct coupling of sediment sources and adjacent accumulation areas. Nonetheless, general models of alluvial-fan evolution and stratigraphy remain elusive, due to the great sensitivity of such systems to allogenic controls and

  20. The Role of Physical Education and Other Formative Experiences of Three Generations of Female Football Fans

    Science.gov (United States)

    Pope, Stacey; Kirk, David

    2014-01-01

    The experiences of female sports fans have been largely marginalised in academic research to date and little research has examined the formative sporting experiences of female spectators. This article draws on 51 semi-structured interviews with three generations of female fans of one (men's) professional football club (Leicester City), to…

  1. The Role of Physical Education and Other Formative Experiences of Three Generations of Female Football Fans

    Science.gov (United States)

    Pope, Stacey; Kirk, David

    2014-01-01

    The experiences of female sports fans have been largely marginalised in academic research to date and little research has examined the formative sporting experiences of female spectators. This article draws on 51 semi-structured interviews with three generations of female fans of one (men's) professional football club (Leicester City), to consider…

  2. Bottom of the Iceberg: The Archontic Text - Review of Fanged Fan Fiction (McFarland, 2013)

    DEFF Research Database (Denmark)

    Schubart, Rikke

    2014-01-01

    Anmeldelse af Lindgren, Maria og Malin Isaksson, Fanged Fan Fiction: Variations on Twilight, True Blood and The Vampire Diaries (McFarland, 2013)......Anmeldelse af Lindgren, Maria og Malin Isaksson, Fanged Fan Fiction: Variations on Twilight, True Blood and The Vampire Diaries (McFarland, 2013)...

  3. Fangirls as Teachers: Examining Pedagogic Discourse in an Online Fan Site

    Science.gov (United States)

    Lammers, Jayne C.

    2013-01-01

    Videogames, such as "The Sims," are a digital media passion drawing adolescents to online spaces where they create and share content. This article explores how discourses and expectations are taught in one online, videogame-related fan site of adolescents who read and write "Sims" fan fiction. Using Bernstein's pedagogic…

  4. "Past the brink of tacit support": Fan activism and the Whedonverses

    Directory of Open Access Journals (Sweden)

    Tanya R. Cochran

    2012-06-01

    Full Text Available For decades, the phrase fan activism has referred almost exclusively to television fans' efforts to save their favorite series. These campaigns—dating at least as far back as the original Star Trek (1966–69 to the more recent Farscape (1999–2003, Firefly (2002–3, Jericho (2006–8, and Veronica Mars (2004–7, among others—appear effective at catalyzing fan involvement, yet are largely ineffective at saving series. In other words, while it may achieve some secondary, albeit significant, victories such as tighter-knit relationships among fans, fan crusading rarely seems to end with the supposed primary goal of activist labors: more installments of the texts devotees admire and love. Recently, however, the phenomenon of fan activism has taken on a new dimension, and scholars are beginning to take note by asking several important questions. As Henry Jenkins asks, how does a fan move from "participatory culture to public participation"? And what does this move mean? As one might expect, there are many reasons for and implications that emerge from this reallocation of such devoted attention. To explore some of those reasons and implications, the author considers some of the devotees of television auteur Joss Whedon, their activist efforts, and the distinct ways Whedon inspires a politically participatory fan following. Ultimately, the author contends that through their activism, many enthusiasts of the Whedonverses extend the worlds of Whedon's stories by consciously constructing a sociopolitical, feminist identity.

  5. Portable Life Support System 2.5 Fan Design and Development

    Science.gov (United States)

    Quinn, Gregory; Carra, Michael; Converse, David; Chullen, Cinda

    2016-01-01

    NASA is building a high-fidelity prototype of an advanced Portable Life Support System (PLSS) as part of the Advanced Exploration Systems Program. This new PLSS, designated as PLSS 2.5, will advance component technologies and systems knowledge to inform a future flight program. The oxygen ventilation loop of its predecessor, PLSS 2.0, was driven by a centrifugal fan developed using specifications from the Constellation Program. PLSS technology and system parameters have matured to the point where the existing fan will not perform adequately for the new prototype. In addition, areas of potential improvement were identified with the PLSS 2.0 fan that could be addressed in a new design. As a result, a new fan was designed and tested for the PLSS 2.5. The PLSS 2.5 fan is a derivative of the one used in PLSS 2.0, and it uses the same nonmetallic, canned motor, with a larger volute and impeller to meet the higher pressure drop requirements of the PLSS 2.5 ventilation loop. The larger impeller allows it to operate at rotational speeds that are matched to rolling element bearings, and which create reasonably low impeller tip speeds consistent with prior, oxygen-rated fans. Development of the fan also considered a shrouded impeller design that could allow larger clearances for greater oxygen safety, assembly tolerances and particle ingestion. This paper discusses the design, manufacturing and performance testing of the new fans.

  6. The Role of Physical Education and Other Formative Experiences of Three Generations of Female Football Fans

    Science.gov (United States)

    Pope, Stacey; Kirk, David

    2014-01-01

    The experiences of female sports fans have been largely marginalised in academic research to date and little research has examined the formative sporting experiences of female spectators. This article draws on 51 semi-structured interviews with three generations of female fans of one (men's) professional football club (Leicester City), to consider…

  7. 75 FR 37453 - Notice of Issuance of Final Determination Concerning Dimmer and Fan Speed Switch Controls

    Science.gov (United States)

    2010-06-29

    ... Agreements Act of 1979; Country of Origin of Titan dimmer and fan speed switch control; substantial.... This case involves two models: the Titan model dimmer and fan speed switch control and the Harmony... components into the finished product. The titan dimmer has a total of 34 components in addition to the...

  8. Discrete-Frequency Radiated Noise and Unsteady Rotor Force from a Subsonic Axial Flow Fan

    Science.gov (United States)

    1988-07-01

    modification ( Tarzan , Muffin, Muffin XL, and Patriot) performed by Fitzgerald [16,17]. He *i used an unobstructed inflow for the fans and found that the...Washburn [18] conducted a very systematic study of the tonal radiation from the Muffin XL and Tarzan fan models. He introduced idealized inflow disturbances

  9. Using the FAN Approach to Deepen Trauma-Informed Care for Infants, Toddlers, and Families

    Science.gov (United States)

    Heffron, Mary Claire; Gilkerson, Linda; Cosgrove, Kimberly; Heller, Sherryl Scott; Imberger, Jaci; Leviton, Audrey; Mueller, Mary; Norris-Shortle, Carole; Phillips, Caroline; Spielman, Eda; Wasserman, Kate

    2016-01-01

    Erikson Institute Fussy Baby Network® (FBN) leaders from around the country have been considering the importance of building trauma-informed service programs. In this article, they discuss ways that the Facilitating Attuned Interaction (FAN) approach and the core processes used by the FAN can be helpful both when trauma is an unexpected presence…

  10. Acoustic modeling of fan noise generation and scattering in a modular duct system

    NARCIS (Netherlands)

    Nijhof, Marten; Beltman, Marco; Wijnant, Ysbrand; Boer, de André

    2005-01-01

    Fan noise is an important noise source in computers. The noise spectrum of fans contains tonal noise, found at the so-called Blade Passing Frequency (BPF) and its higher harmonics, that plays an important role in the perceived sound quality. An acoustic resonator integrated in the duct of an in-duct

  11. Geometric-Phase Polarization Fan-out Grating Fabricated with Deep-UV Interference Lithography

    Science.gov (United States)

    Wan, Chenhao; Lombardo, David; Sarangan, Andrew; Zhan, Qiwen

    2017-06-01

    We report the design, fabrication and testing of a highly efficient polarization fan-out grating for coherent beam combining working at 1550 nm. The grating design exploits the geometric-phase effect. Deep-UV interference lithography is used to fabricate the designed grating. Such a polarization fan-out grating demonstrates several advantages that are ideal for laser beam combining.

  12. Fifty shades of exploitation: Fan labor and Fifty Shades of Grey

    Directory of Open Access Journals (Sweden)

    Bethan Jones

    2014-03-01

    Full Text Available This exploration of the debates that have taken place in fandom over the ethics of pulling fan fiction and publishing it as original work draws on the notion of the fannish gift economy, which postulates that gifts such as fan fiction and fan art have value in the fannish community because they are designed to create and cement its social structure. Tension exists between fans who subscribe to the notion of a fannish gift economy and those who exploit fandom by using it to sell their pulled-to-publish works. An examination of E. L. James's 2012 Fifty Shades trilogy (comprising the books Fifty Shades of Grey, Fifty Shades Darker, and Fifty Shades Freed, which began as Twilight fan fiction, in addition to Twilight fan art sold through sites such as Redbubble and Etsy, demonstrates a tension between the two modes of fan expression: sale of artworks appears to be an acceptable practice in fandom, but the commercial sale of fan fic, even when marketed as original fiction, is widely contested.

  13. Fangirls as Teachers: Examining Pedagogic Discourse in an Online Fan Site

    Science.gov (United States)

    Lammers, Jayne C.

    2013-01-01

    Videogames, such as "The Sims," are a digital media passion drawing adolescents to online spaces where they create and share content. This article explores how discourses and expectations are taught in one online, videogame-related fan site of adolescents who read and write "Sims" fan fiction. Using Bernstein's pedagogic…

  14. Towards a three-component model of fan loyalty: a case study of Chinese youth

    National Research Council Canada - National Science Library

    Zhang, Xiao-xiao; Liu, Li; Zhao, Xian; Zheng, Jian; Yang, Meng; Zhang, Ji-qi

    2015-01-01

    .... The present study explored the meaning of fan loyalty in the context of China. Data were collected by the method of in-depth interviews with 16 young Chinese people aged between 19 and 25 years who currently or once were pop fans...

  15. Autogenic dynamics of alluvial fans in endorheic basins: Outcrop examples and stratigraphic significance

    NARCIS (Netherlands)

    Ventra, D.; Nichols, G.J.

    2014-01-01

    Alluvial fans are relatively simple depositional systems, due to the direct coupling of sediment sources and adjacent accumulation areas. Nonetheless, general models of alluvial-fan evolution and stratigraphy remain elusive, due to the great sensitivity of such systems to allogenic controls and thei

  16. Measurement of airflow and pressure characteristics of a fan built in a car ventilation system

    Directory of Open Access Journals (Sweden)

    Pokorný Jan

    2016-01-01

    Full Text Available The aim of this study was to identify a set of operating points of a fan built in ventilation system of our test car. These operating points are given by the fan pressure characteristics and are defined by a pressure drop of the HVAC system (air ducts and vents and volumetric flow rate of ventilation air. To cover a wide range of pressure drops situations, four cases of vent flaps setup were examined: (1 all vents opened, (2 only central vents closed (3 only central vents opened and (4 all vents closed. To cover a different volumetric flows, the each case was measured at least for four different speeds of fan defined by the fan voltage. It was observed that the pressure difference of the fan is proportional to the fan voltage and strongly depends on the throttling of the air distribution system by the settings of the vents flaps. In case of our test car we identified correlations between volumetric flow rate of ventilation air, fan pressure difference and fan voltage. These correlations will facilitate and reduce time costs of the following experiments with this test car.

  17. Measurement of airflow and pressure characteristics of a fan built in a car ventilation system

    Science.gov (United States)

    Pokorný, Jan; Poláček, Filip; Fojtlín, Miloš; Fišer, Jan; Jícha, Miroslav

    2016-03-01

    The aim of this study was to identify a set of operating points of a fan built in ventilation system of our test car. These operating points are given by the fan pressure characteristics and are defined by a pressure drop of the HVAC system (air ducts and vents) and volumetric flow rate of ventilation air. To cover a wide range of pressure drops situations, four cases of vent flaps setup were examined: (1) all vents opened, (2) only central vents closed (3) only central vents opened and (4) all vents closed. To cover a different volumetric flows, the each case was measured at least for four different speeds of fan defined by the fan voltage. It was observed that the pressure difference of the fan is proportional to the fan voltage and strongly depends on the throttling of the air distribution system by the settings of the vents flaps. In case of our test car we identified correlations between volumetric flow rate of ventilation air, fan pressure difference and fan voltage. These correlations will facilitate and reduce time costs of the following experiments with this test car.

  18. Performance and Internal Flow of Sirocco Fan Using Contra-Rotating Rotors

    Institute of Scientific and Technical Information of China (English)

    J. Fukutomi; T.Shigemitsu; T. Yasunobu

    2008-01-01

    A sirocco fan using contra-rotating rotors in which an inner rotor is settled inside the sirocco fan rotor end each rotor rotates in an opposite direction was proposed for the purpose of getting the higher pressure and making the structure of a sirocco fan more compact. If the high discharge pressure is obtained with the adoption of the contra-rotating rotors, it could be used for various purposes. Pressure coefficient of a sirocco fan with contra-rotating rotors is 2.5 times as high as the conventional sirocco fan and the maximum efficiency point of contra-rotating rotors shifts to larger flow rate than a conventional sirocco fan. On the other hand, it was clarified from the flow measurement results that circumferential velocity component at the outlet of the outer rotor of contra-rotating rotors becomes larger than a conventional one. In the present paper, the performance of a conventional sirocco fan and a sirocco fan with contra-rotating rotors are shown and the internal flow field at the outlet of outer rotor of both cases is clarified. Then, the effect of different kind of contra-rotating rotors on the performance and internal flow field is investigated and the rotor design with higher performanco would be discussed.

  19. Relativistic Treatment of Spinless Particles Subject to a Rotating Deng-Fan Oscillator

    Institute of Scientific and Technical Information of China (English)

    DONG Shi-Hai

    2011-01-01

    The bound state solutions of the Klein-Gordon equation with the rotating Deng-Fan molecular potential are presented by using a proper approximation to the centrifugal term within the framework of equal scalar and vector Deng-Fan potentials. It is shown that the solutions can be expressed by the generalized hypergeometric functions. The normalized wavefunctions are also derived.

  20. Numerical Experiment of the Solid Particle Erosion of Bionic Configuration Blade of Centrifugal Fan

    Institute of Scientific and Technical Information of China (English)

    Junqiu ZHANG; Zhiwu HAN; Wei YIN; Huiyuan WANG; Chao GE; Jialian JIANG

    2013-01-01

    In this paper,a bionic method was presented to improve the erosion resistance of blade of the centrifugal fan.A numerical investigation of the solid particle erosion on the standard and bionic configuration blade of 4-72N_o10C centrifugal fan was presented.The numerical study employs computational fluid dynamics (CFD) software,based on a finite volume method,in which the discrete phase model was used to modele the solid particles flow,and the Eulerian conservation equation was adopt to simulate the continuous phase.Moreover,user-defined function was used to define wear equation.The various diameters of the particles were taken into account.The positions of collision of standard and bionic fan blades were discussed,and two kinds of centrifugal fan blade wear were compared.The results show that the particles from the incident source with different positions have different processes of turning and movement when enter into the impeller.The trajectories of flow in the fan channel are significantly different for the particles with different diameters.Bionic fan blade have lower erosion rate than the standard fan blade when the particle size is 20 μm.The anti-erosion mechanism of the bionic fan blade was discussed.

  1. Aliphatic hydrocarbons and triterpenes of the Congo deep-sea fan

    Science.gov (United States)

    Méjanelle, Laurence; Rivière, Béatrice; Pinturier, Laurence; Khripounoff, Alexis; Baudin, François; Dachs, Jordi

    2017-08-01

    Hydrocarbons were analyzed in sediments from the Congo River deep-sea fan, from the Congo River, and in sinking particles collected by sediment traps 40 m above the sediment. Studied sites encompassed three lobes of decreasing age of formation along the canyon: sites A, F and C and a another lobe system, disconnected from the active channel since 4 ka, Site E. Terrestrial long-chain odd n-alkanes were dominant in all sediments of the lobe system. Unsaturated terpenoids sourced by higher plants, such as gammacerene, lupene, ursene and oleanene, were also detected. At site C, characterized by high accumulation rates (10-20 cm yr-1), the organic matter spends less time in the oxic layer than at other sites and high phytadiene concentrations 10-17 μg gOC-1) evidenced recent terrestrial and phytoplanktonic remains reworked in anaerobic conditions. In these sediments, organic carbon-normalized concentrations of terrestrial alkanes and terpenoids were several fold higher than in the lobe sediments with lower accumulation rates (sites A and F), arguing for a more rapid degradation of terrestrial hydrocarbons than bulk organic carbon in the first steps of pre-diagenesis. Ample variations in the contributions of biomarkers from higher plants, ferns, bacteria and angiosperms, indicate an heterogeneous contribution of the soil and vegetation detritus delivered to the Congo lobe sediments. Lower concentrations in terrestrial hydrocarbons at site E, 45 km away from the active canyon, indicated that river particles are still admixed to the dominant marine organic matter. Diploptene and hop-7(21)-ene have a dual origin, from terrestrial and marine microorganisms. Scatter in their relationship to gammacerene argues for a contribution of marine microorganisms, in addition to soils-sourced microorganisms. The close distribution patterns of diploptene, hop-21-ene, hop-7(21)ene and neohop-13(18)-ene is in line with the hypothesis of sequential clay-catalyzed isomerisation of bacterial

  2. Results of an Advanced Fan Stage Operating Over a Wide Range of Speed and Bypass Ratio. Part 1; Fan Stage Design and Experimental Results

    Science.gov (United States)

    Suder, Kenneth L.; Prahst, Patricia S.; Thorp, Scott A.

    2011-01-01

    NASA s Fundamental Aeronautics Program is investigating turbine-based combined cycle (TBCC) propulsion systems for access to space because it provides the potential for aircraft-like, space-launch operations that may significantly reduce launch costs and improve safety. To this end, National Aeronautics and Space Administration (NASA) and General Electric (GE) teamed to design a Mach 4 variable cycle turbofan/ramjet engine for access to space. To enable the wide operating range of a Mach 4+ variable cycle turbofan ramjet required the development of a unique fan stage design capable of multi-point operation to accommodate variations in bypass ratio (10 ), fan speed (7 ), inlet mass flow (3.5 ), inlet pressure (8 ), and inlet temperature (3 ). In this paper, NASA has set out to characterize a TBCC engine fan stage aerodynamic performance and stability limits over a wide operating range including power-on and hypersonic-unique "windmill" operation. Herein, we will present the fan stage design, and the experimental test results of the fan stage operating from 15 to 100 percent corrected design speed. Whereas, in the companion paper, we will provide an assessment of NASA s APNASA code s ability to predict the fan stage performance and operability over a wide range of speed and bypass ratio.

  3. Statistic inversion of multi-zone transition probability models for aquifer characterization in alluvial fans

    CERN Document Server

    Zhu, Lin; Gong, Huili; Gable, Carl; Teatini, Pietro

    2015-01-01

    Understanding the heterogeneity arising from the complex architecture of sedimentary sequences in alluvial fans is challenging. This paper develops a statistical inverse framework in a multi-zone transition probability approach for characterizing the heterogeneity in alluvial fans. An analytical solution of the transition probability matrix is used to define the statistical relationships among different hydrofacies and their mean lengths, integral scales, and volumetric proportions. A statistical inversion is conducted to identify the multi-zone transition probability models and estimate the optimal statistical parameters using the modified Gauss-Newton-Levenberg-Marquardt method. The Jacobian matrix is computed by the sensitivity equation method, which results in an accurate inverse solution with quantification of parameter uncertainty. We use the Chaobai River alluvial fan in the Beijing Plain, China, as an example for elucidating the methodology of alluvial fan characterization. The alluvial fan is divided...

  4. Fan Performance Testing and Oxygen Compatibility Assessment Results for Future Space Suit Life Support Systems

    Science.gov (United States)

    Paul, Heather L.; Jennings, Mallory A.; Vogel, Matthew

    2009-01-01

    An advanced portable life support system (PLSS) for the space suit will require a small, robust, and energyefficient system to transport the ventilation gas through the space suit for lunar Extravehicular Activity (EVA) operations. A trade study identified and compared ventilation transport technologies in commercial, military, and space applications to determine which technologies could be adapted for EVA use. Based on the trade study results, five commercially available, 24-volt fans were selected for performance testing at various pressures and flow rates. Measured fan parameters included fan delta-pressures, input voltages, input electrical currents, and in some cases motor windings electrical voltages and currents. In addition, a follow-on trade study was performed to identify oxygen compatibility issues and assess their impact on fan design. This paper outlines the results of the fan performance characterization testing, as well as the results from the oxygen compatibility assessment.

  5. Energy-optimal speed control of fans and compressor in a refrigeration system

    DEFF Research Database (Denmark)

    Jakobsen, Arne; Rasmussen, Bjarne D.

    1998-01-01

    Use of variable speed compressors and variable speed fans for both the evaporator and the condenser makes the refrigeration system more flexible, adds to the degree of freedom of the control system and therefore makes it possible to (on-line) optimise the various speeds involved. Say, for example...... choosing the combination of compressor speed, evaporator fan and condenser fan speeds which minimises the total power consumption of the motors involved. A system and integrated control viewpoint is necessary as a “component-oriented” and “single-loop-control” approach will not lead to the discovery...... that the cooling capacity must be increased due to increased cooling load. This can be done by increasing the compressor speed and/or the evaporator fan speed and also to some extent by increasing the condenser fan speed. The general control problem is to obtain the desired temperature of the cooled air, while...

  6. Unsteady Operation of New Type Turbofan Engine with Aerodynamic Torque Converter Reducing Front Fan Speed

    Institute of Scientific and Technical Information of China (English)

    Toshiaki KANEMOTO; Seita SEKI; Kazunori IDENO; Ahmed Mohamed GALAL

    2005-01-01

    It is desired to increase the rotational speed of the core engine of the turbofan so as to get the best efficiency for the next leap of engine technology. The conventional mechanism in which the front fan is directly connected to the output shaft of a core engine, have a limit of increasing the spool speed, because the fan diameter is very large. The authors have proposed a new driving system in which the front fan is driven through the aerodynamic torque converter. The front fan can work at the best performance at slower speed while the core engine runs more efficiently at higher speed. Continuously, this paper discusses the response of the front fan in the unsteady operation of the core engine, accompanying with the internal flow. The system has the acceptable responsibility in the unsteady operation which is very important for the aircrafts.

  7. Numerical Simulation of Capillary Flow in Fan-Shaped Asymmetric Interior Corner Under Microgravity

    Science.gov (United States)

    Yong-Qiang, Li; Wen-Hui, Cao; Ling, Liu

    2017-02-01

    Based on fluid mechanics theories, this research focuses on numerical simulation and analysis of capillary flow under microgravity in fan-shaped asymmetric interior corner. We analyze the effect the contact angle has on rising height in a fan-shaped asymmetric interior corner, and get the Concus-Finn condition the calculation of capillary flow needs to satisfy in fan-shaped asymmetric interior corner. Then we study the effect that different parameters of experimental medium and container configuration has on capillary flow in fan-shaped asymmetric interior corner when Concus-Finn condition is fulfilled. The conclusions of this paper has an important role in guiding the analytic solution of flow in a fan-shaped asymmetric interior corner under microgravity. We can also chose the appropriate experimental medium and design a container based on this paper.

  8. A Preliminary Axial Fan Design Method with the Considerat ion of Performance and Noise Characteristics

    Science.gov (United States)

    Lee, Chan; Kil, Hyun Gwon

    2010-06-01

    Presented in this paper are a fan's aero-acoustic performance method and its computation procedure which combines aerodynamic flow field data, performances and noise levels of fan. The internal flow field and the performance of fan are analyzed by the through-flow modeling, inviscid pitch-averaged quasi-3D flow analysis combined with flow deviation and pressure loss distribution models. Based on the predicted internal flow field dada by the trough-flow modeling, fan noise is predicted by two models for the discrete frequency noise due to rotating steady aerodynamic thrust and blade interaction and for the broadband noise due to turbulent boundary layer and wake vortex shedding. The present predictions of the flow distribution, the performance and the noise level of fan are well agreed with actual test results.

  9. Aerodynamic performance of two fifteen-percent-scale wind-tunnel drive fan designs

    Science.gov (United States)

    Signor, D. B.; Borst, H. V.

    1986-01-01

    An experimental and analytical investigation of two fan blade designs was conducted. The fan blades tested were 15 percent scale models of the blades used in the National Full Scale Aerodynamic Complex fan drive at NASA Ames Research Center. The fan blades were composed of NACA-65 and modified NACA-65-series airfoil design sections. The blades with modified 65-series sections incorporated increased thickness on the upper surface, between the leading edge and the one-half chord position. Twist and taper were the same for both blade designs. The fan blades with modified 65-series sections were found to have an increase in stall margin when they were compared with the unmodified blades. The experimental performance data agreed favorably with theoretical calculations.

  10. Creative choices and fan practices in the transformation of theme park space

    Directory of Open Access Journals (Sweden)

    Carissa Ann Baker

    2016-09-01

    Full Text Available This article describes and interprets fan activities within the theme park space related to a particular fan object. It examines an evolving paradigm wherein the role of theme park visitors is changed. Rather than being perceived as observers of spectacles, they can participate and interact with the environment in new ways. An example of this is Sorcerers of the Magic Kingdom (2012, an interactive role-playing quest and collector card game at Disney's Magic Kingdom Park in Florida. Fans participate in a variety of practices that have dynamically redefined theme park activities. Together, management, designers, and fans have cocreated and reconstructed the theme park experience as one of exploration and participation. Despite multiple levels of control, fans will likewise persist in engagement with activities (in park and online that help shape and interrogate the theme park space.

  11. Acoustic evaluation of a novel swept-rotor fan. [noise reduction in turbofan engines

    Science.gov (United States)

    Lucas, J. G.; Woodward, R. P.; Mackinnon, M. J.

    1978-01-01

    Inlet noise and aerodynamic performance are presented for a high tip speed fan designed with rotor blade leading edge sweep that gives a subsonic component of inlet Mach number normal to the edge at all radii. The intent of the design was to minimize the generation of rotor leading edge shock waves thereby minimizing multiple pure tone noise. Sound power level and spectral comparisons are made with several high-speed fans of conventional design. Results show multiple pure tone noise at levels below those of some of the other fans and this noise was initiated at a higher tip speed. Aerodynamic performance of the fan did not meet design goals for this first build which applied conventional design procedures to the swept fan geometry.

  12. Aero-Acoustics of Modern Transonic Fans—Fan Noise Reduction from Its Sources

    Institute of Scientific and Technical Information of China (English)

    L. Xu; J.D. Denton

    2003-01-01

    The noise of aerodynamics nature from modern transonic fan is examined from its sources with the perspective of noise reduction through aero-acoustics design using advanced Computational Fluid Dynamics (CFD) tools.In particular the problems associated with the forward propagating noise in the front is addressed. It is identified that the shock wave spillage from the leading edge near the fan tip is the main source of the tone noise. Two different approaches have been studied to reduce the forward arc tone noise and two state-of-art transonic fans are designed using the strategies developed. The following rig tests show that while the fans exhibit other noise problems,the primary goals of noise reduction have been achieved through both fans and the novel noise reduction concept vindicated.

  13. OPTIMIZATION DESIGN OF GAS-PARTICLE TWO-PHASE AXIAL-FLOW FAN

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    Based on the shaping theory of writhed blade in streamline design, the geometric shape of blade is designed and then computational formulas for the dynamic design of fan with writhed the blades in gas-particle two-phase axial-flow are derived with the two-phase continuum coupling model. Concurrently, the correlation between the structure of impeller and flow-field dynamic functional parameters is presented. Further, the software for the optimization design of gas-particle two-phase axial-flow fan with writhed blades is obtained. By means of the available software, a sample fan is formed with its all dynamic characteristic curves and geometric shape. Finally, the conclusion on the effect of particles on fan running is reached, quantitatively and qualitatively, as is expected in the fan industry.

  14. Self-organzatonal interacton as a factor of fan groups survival

    Directory of Open Access Journals (Sweden)

    S. S. Baranova

    2016-06-01

    Also in this study the matter of survival of social groups is examined though the synergetic approach. Survival of the football fan groups is presented as a result of the overcoming the internal entropy of the system. In addition, in the end of the article the implementation of value basis and their functions in the self-organized football fan groups are discussed. The author demonstrates the social importance of the informal internal «code» for football fans. This s how the author defines the role of the self-organization as a factor of the football fan groups survival. Thus, the inner football fans corporate culture is seen not only as a system that is capable of self-regulation, but also as a basic condition for self-organization.

  15. Partially inverted, mixed grain size alluvial fans in the Atacama Desert as analogues for Martian sediment fans

    Science.gov (United States)

    Hobley, D. E.; Howard, A. D.

    2011-12-01

    Martian alluvial fans have now been recognized in many craters around the equatorial latitudes of Mars. HiRISE imagery reveals that their surfaces often show a radial pattern of narrow (10s to 100s of meters), long (km), low relief (thread, with some anastomosing reaches. Almost all flows transport abundant muds as well as a coarser load of cobbles and larger clasts. Occasionally this mud fraction may instead be replaced by sandier material, but this contrast makes little difference to the bulk channel form. Low natural levees are present around many channels, but lobate sheets of fine sediment are ubiquitous beyond these, indicating very frequent overtopping of the levees by hyperconcentrated flows. The main channel course also avulses frequently. Once inactive, channels subsequently begin to be inverted by wind erosion and winnowing of fines, and the second order surface texture of the eroded surfaces and the orientation of some channel segments are both controlled by the wind direction. The first order degradation of the individual channel lobes however is not well predicted by the deposit age and hence duration of exposure. Instead, the original grain size distribution of the deposit and the channel form are of comparable importance. We are developing a numerical model of concurrent fan deposition and inversion to further understand and quantify these processes.

  16. FCJ-171 Expectations denied: Fan and industry conflict around the localisation of the Japanese video game Yakuza 3

    Directory of Open Access Journals (Sweden)

    Craig Norris

    2014-12-01

    Full Text Available Online fan cultures provides researchers with a space to observe and analyse the development and establishment of fan participation with media properties. The visibility of, and zealous postings by, fans on online forums offers a valuable opportunity to explore what happens when fans feel their expectations are being denied or limited by creator or industry actions. This article examines the fallout around the localisation of the Japanese video game Yakuza 3 into the West in 2010.

  17. Development of high-performance and low-noise axial-flow fan units in their local operating region

    Energy Technology Data Exchange (ETDEWEB)

    Heo, Seung; Ha, Min Ho; Cheong, Cheol Ung [Pusan National University, Busan (Korea, Republic of); Kim, Tae Hoon [LG Electronics Inc., Changwon (Korea, Republic of)

    2015-09-15

    Aerodynamic and aeroacoustic performances of an axial-flow fan unit are improved by modifying its housing structure without changing the fan blade. The target axial-flow fan system is used to lower temperature of a compressor and a condenser in the machine room of a household refrigerator which has relatively high system resistance due to complex layout of structures inside it. First, the performance of the fan system is experimentally characterized by measuring its volume flow rate versus static pressure using a fan performance tester satisfying the AMCA (Air Movement and Control Association) regulation, AMCA 210-07. The detailed structure of flow driven by the fan is numerically investigated using a virtual fan performance tester based on computational fluid dynamics techniques. The prediction result reveals possible loss due to radial and tangential velocity components in the wake flow downstream of the fan. The length of the fan housing is chosen as a design parameter for improving the aerodynamic and aeroacoustic performances of the fan unit by reducing the identified radial and tangential velocity components. Three fan units with different housing lengths longer than the original are analyzed using the virtual fan performance tester. The results confirm the improved aerodynamic performance of the proposed three designs. The flow field driven by the proposed fan unit is closely examined to find the causes for the observed performance improvements, which ensures that the radial and tangential velocity components in the wake flow are reduced. Finally, the improved performance of the proposed fan systems is validated by comparing the P-Q and efficiency curves measured using the fan performance tester. The noise emission from the household refrigerator is also found to be lessened when the new fan units are installed.

  18. Morphology and sedimentology of two contemporary fan deltas on the southeastern Baja California Peninsula, Mexico

    Science.gov (United States)

    Nava-Sanchez, Enrique; Cruz-Orozco, Rodolfo; Gorsline, Donn S.

    1995-08-01

    The San Juan de Los Planes drainage basin is located on the southeastern margin of the Baja California Peninsula, approximately 20 km southeast of the city of La Paz. Pleistocene alluvial fans have been built into the basin from the surrounding areas of high relief and are presently being eroded. At the fan apex, the dissection depth ranges from 20 to 40 m, and is 6 to 15 m at the coast. The sediments have been redeposited in several active modern fan deltas built out into the narrow shelf of La Ventana Bay. Shelf width ranges from 0 to 5 km (average 3 km). Wave energy is delivered from southeasterly storms and from the local sea breeze winds; the respective wave heights average 2 and 1 m. The Agua Caliente and Las Canoas fan deltas, the subjects of this paper, are located on the active El Sargento Fault Zone and are fed by channels that deeply dissect the older fan surfaces. The Agua Caliente fan delta is a classic Gilbert-type delta with a steeply inclined delta front. Wave reworking and redistribution of the sediments at the delta face are important and a wave-cut terrace has developed at about 6 m depth. The Las Canoas fan delta is a shoal-water-profile, Hjulstrom type with a gently inclined delta front. Wave energy is less important. The alignments of the coasts of both fans are controlled by the fault line. Sediment supply is largest for the Las Canoas fan delta. The fan deltas are examples of this depositional form as it has developed in an arid, tectonically active, high-relief and narrow neo-trailing edge margin.

  19. Fan cooling of the resting area in a free stalls dairy barn.

    Science.gov (United States)

    Calegari, Ferdinando; Calamari, Luigi; Frazzi, Ermes

    2014-08-01

    This summer study evaluated the effect of providing additional fans (cooling) in the resting area within a free-stall dairy barn that had fans and sprinklers in the feeding area and paddock availability. Thirty cows were divided into two homogenous groups and kept in two pens: one had the resting area equipped with two fans (FAN) while no fans were added to the other resting area (CON). Microclimatic parameters, rectal temperature (RT), breathing rate (BR), milk yield, and milk pH traits were recorded. Time budgeting and the behaviour of the cows (time spent in the feeding area, standing and lying in other areas) were also recorded using digital video technology. Two slight-to-moderate heat waves were observed. During the hottest period the daily maximum temperature recorded was 33.5 °C and the daily maximum THI was 81.6. During this period, the BR and RT increased only slightly in both groups, with lower BR (n.s.) in FAN compared with CON. Milk yield was better maintained (n.s.) in FAN compared with CON during the hottest period. The FAN cows showed a greater (Pfree stalls (9.5 and 8.6 h/day in FAN and CON, respectively), whereas CON cows made greater (P<0.05) use of the paddock during evening and late evening hours. Consequently, the total daily lying time was 13.5 h/day in both groups. In conclusion, the results suggest that using fans in the resting area improves cow comfort, which increases use of the resting area. The lying time results also suggest that the benefits of providing ventilation in the resting area might be more evident in barns where there is no paddock.

  20. Channel Networks on Large Fans: Refining Analogs for the Ridge-forming Unit, Sinus Meridiani

    Science.gov (United States)

    Wilkinson, Justin

    2009-01-01

    Stream channels are generally thought of as forming within confined valley settings, separated by interfluves. Sinuous ridges on Mars and Earth are often interpreted as stream channels inverted by subsequent erosion of valley sides. In the case of the ridge-forming unit (RFU), this interpretation fails to explain the (i) close spacing of the ridges, which are (ii) organized in networks, and which (iii) cover large areas (approximately 175,000 km (exp 2)). Channel networks on terrestrial fans develop unconfined by valley slopes. Large fans (100s km long) are low-angle, fluvial features, documented worldwide, with characteristics that address these aspects of the RFU. Ridge patterns Channels on large fans provide an analog for the sinuous and elongated morphology of RFU ridges, but more especially for other patterns such as subparallel, branching and crossing networks. Branches are related to splays (delta-like distributaries are rare), whose channels can rejoin the main channel. Crossing patterns can be caused by even slight sinuosity splay-related side channels often intersect. An avulsion node distant from the fan apex, gives rise to channels with slightly different, and hence intersecting, orientations. Channels on neighboring fans intersect along the common fan margin. 2. Network density Channels are the dominant feature on large terrestrial fans (lakes and dune fields are minor). Inverted landscapes on subsequently eroded fans thus display indurated channels as networks of significantly close-spaced ridges. 3. Channel networks covering large areas Areas of individual large terrestrial fans can reach >200,000 km 2 (105-6 km 2 with nested fans), providing an analog for the wide area distribution of the RFU.

  1. Morphometry and Geomorphic Characteristics of Large Alluvial fans and Megafans in South America

    Science.gov (United States)

    Latrubesse, E. M.; Sounny-Slitine, M. A.

    2015-12-01

    Alluvial megafans are 'large' fan-shaped bodies of sediment that form from lateral migrations of a river as it exits a topographic front. They differ from large alluvial fans (radial length between 30-100km) with sizes greater than 100-km in radial length. This study characterizes and describes megafans and large alluvial fan through morphometrics. We cataloged the fans into a geodatabase delineating size and extent of basins both upstream and downstream from the apex. Through remote sensing, elevation modeling and geomorphic mapping, we populated the database with fan morphometric measurements, qualitative descriptions and basin parameters. Metrics include planform area, catchment area, gradient, relief index, drainage density, and others. These were compared to longitudinal/transverse profiles, satellite imagery, and geomorphic maps. The database is global, however since the largest megafans of the world are located in South America, this preliminary analysis will focus on the continent. We found morphometric and characteristic differences between large alluvial fans and megafans in the region. These include difference in relationship between morphometrics, for example the ratio between catchment and fan size area. These properties of fans could be a better approach in differentiating megafans from large alluvial fans. The current criteria is an artificial scale divide, which varies in the literature, with the most common being a 100-km apex-to-toe length. Alternative values as little of 30-km apex-to-toe length have been proposed, as well as alternative metrics like coverage areas of greater than 10,000 square-km. We propose that geomorphic characteristics and morphometrics provide an intrinsic approach to differentiating megafans from larger alluvial fans.

  2. Stratigraphy, depositional rates, and other DSDP Leg 96 conclusions: Mississippi fan

    Energy Technology Data Exchange (ETDEWEB)

    Coleman, J.M.; Bouma, A.H.

    1984-04-01

    The Quaternary Mississippi fan consists of at least seven seismically mappable fan lobes. Eight sites were drilled into the youngest fan lobe during DSDP Leg 96. The Holocene (Ericson Zone Z) is capped by a marly foraminiferal ooze. Assuming an age of 12,000 yr for the Holocene/Pleistocene boundary, a minimum accumulation rate of 3-30 cm/1000 yr (1-12 in/1000 yr) is computed for the Holocene. The youngest fan lobe was deposited during the upper part of Ericson Zone Y (late Wisconsin glacial, 12,000-85,000 y.B.P.). Deposition rates for the Y Zone are extremely high for the middle fan sites, averaging 12 m/1000 yr (39 ft/1000 yr). Lower fan accumulation rates are 7 m/1000 yr (23 ft/1000 yr) for the channel sites and 6 m/1000 yr (20 ft/1000 yr) for the channel-mouth depositional lobes. These rates are not corrected for compaction. Foraminifera are scarce; the occurrence of shallow-water benthic species indicates a displaced inner and middle neritic origin for the sediments. Drilling on the youngest fan lobe shows that most of the silts and sands were transported through the upper and middle fan channel onto the lower fan, producing a 6 to 10-km (4 to 6-mi) wide, 135-m (443-ft) thick aggradational channel deposit. Much of the fine-grained sediment spilled out of the channel onto the adjacent overbank areas, constructing broad marginal plain. The channels on the lower fans are smaller and shift position frequently. Channel-mount depositional lobes are constructed at the end of the active channels and are composed of more than 50% net sand.

  3. Effect of tip flange on tip leakage flow of small axial flow fans

    Science.gov (United States)

    Zhang, Li; Jin, Yingzi; Jin, Yuzhen

    2014-02-01

    Aerodynamic performance of an axial flow fan is closely related to its tip clearance leakage flow. In this paper, the hot-wire anemometer is used to measure the three dimensional mean velocity near the blade tips. Moreover, the filtered N-S equations with finite volume method and RNG k-ɛ turbulence model are adopted to carry out the steady simulation calculation of several fans that differ only in tip flange shape and number. The large eddy simulation and the FW-H noise models are adopted to carry out the unsteady numerical calculation and aerodynamic noise prediction. The results of simulation calculation agree roughly with that of tests, which proves the numerical calculation method is feasible.The effects of tip flange shapes and numbers on the blade tip vortex structure and the characteristics are analyzed. The results show that tip flange of the fan has a certain influence on the characteristics of the fan. The maximum efficiencies for the fans with tip flanges are shifted towards partial flow with respect to the design point of the datum fan. Furthermore, the noise characteristics for the fans with tip flanges have become more deteriorated than that for the datum fan. Tip flange contributes to forming tip vortex shedding and the effect of the half-cylinder tip flange on tip vortex shedding is obvious. There is a distinct relationship between the characteristics of the fan and tip vortex shedding. The research results provide the profitable reference for the internal flow mechanism of the performance optimization of small axial flow fans.

  4. Experimental impact testing and analysis of composite fan cases

    Science.gov (United States)

    Vander Klok, Andrew Joe

    For aircraft engine certification, one of the requirements is to demonstrate the ability of the engine to withstand a fan blade-out (FBO) event. A FBO event may be caused by fatigue failure of the fan blade itself or by impact damage of foreign objects such as bird strike. An un-contained blade can damage flight critical engine components or even the fuselage. The design of a containment structure is related to numerous parameters such as the blade tip speed; blade material, size and shape; hub/tip diameter; fan case material, configuration, rigidity, etc. To investigate all parameters by spin experiments with a full size rotor assembly can be prohibitively expensive. Gas gun experiments can generate useful data for the design of engine containment cases at much lower costs. To replicate the damage modes similar to that on a fan case in FBO testing, the gas gun experiment has to be carefully designed. To investigate the experimental procedure and data acquisition techniques for FBO test, a low cost, small spin rig was first constructed. FBO tests were carried out with the small rig. The observed blade-to-fan case interactions were similar to those reported using larger spin rigs. The small rig has the potential in a variety of applications from investigating FBO events, verifying concept designs of rotors, to developing spin testing techniques. This rig was used in the developments of the notched blade releasing mechanism, a wire trigger method for synchronized data acquisition, high speed video imaging and etc. A relationship between the notch depth and the release speed was developed and verified. Next, an original custom designed spin testing facility was constructed. Driven by a 40HP, 40,000rpm air turbine, the spin rig is housed in a vacuum chamber of phi72inx40in (1829mmx1016mm). The heavily armored chamber is furnished with 9 viewports. This facility enables unprecedented investigations of FBO events. In parallel, a 15.4ft (4.7m) long phi4.1inch (105mm

  5. "Bohr's Atomic Model."

    Science.gov (United States)

    Willden, Jeff

    2001-01-01

    "Bohr's Atomic Model" is a small interactive multimedia program that introduces the viewer to a simplified model of the atom. This interactive simulation lets students build an atom using an atomic construction set. The underlying design methodology for "Bohr's Atomic Model" is model-centered instruction, which means the central model of the…

  6. The atomic orbitals of the topological atom.

    Science.gov (United States)

    Ramos-Cordoba, Eloy; Salvador, Pedro; Mayer, István

    2013-06-07

    The effective atomic orbitals have been realized in the framework of Bader's atoms in molecules theory for a general wavefunction. This formalism can be used to retrieve from any type of calculation a proper set of orthonormalized numerical atomic orbitals, with occupation numbers that sum up to the respective Quantum Theory of Atoms in Molecules (QTAIM) atomic populations. Experience shows that only a limited number of effective atomic orbitals exhibit significant occupation numbers. These correspond to atomic hybrids that closely resemble the core and valence shells of the atom. The occupation numbers of the remaining effective orbitals are almost negligible, except for atoms with hypervalent character. In addition, the molecular orbitals of a calculation can be exactly expressed as a linear combination of this orthonormalized set of numerical atomic orbitals, and the Mulliken population analysis carried out on this basis set exactly reproduces the original QTAIM atomic populations of the atoms. Approximate expansion of the molecular orbitals over a much reduced set of orthogonal atomic basis functions can also be accomplished to a very good accuracy with a singular value decomposition procedure.

  7. Promoting fan engagement: An exploration of the fundamental motives for sport consumption amongst premier league football spectators

    NARCIS (Netherlands)

    Stander, Frederick W.; van Zyl, Llewellyn E.; Motaung, Kemiso

    2016-01-01

    The aim of this study was to examine whether fan engagement could be predicted by the motivational dimensions of sport consumption. A sample of 806 football sport fans (African = 85%, male = 67.4%, part of an organised supporters club = 57.6%) were participants. They completed the Fan Engagement

  8. Promoting fan engagement: An exploration of the fundamental motives for sport consumption amongst premier league football spectators

    NARCIS (Netherlands)

    Stander, Frederick W.; Zyl, van Llewellyn E.; Motaung, Kemiso

    2016-01-01

    The aim of this study was to examine whether fan engagement could be predicted by the motivational dimensions of sport consumption. A sample of 806 football sport fans (African = 85%, male = 67.4%, part of an organised supporters club = 57.6%) were participants. They completed the Fan Engagement Sca

  9. Using Synthetic Aperture Radar data of terrestrial analogs to test for alluvial fan formation mechanisms on Titan

    Science.gov (United States)

    Cartwright, R. J.; Burr, D. M.

    2017-03-01

    Landforms on Titan include features hypothesized to be alluvial fans. Terrestrial alluvial fans form via two processes: fluid-gravity flows (sheetfloods) and sediment-gravity flows (debris flows). Along the Panamint Mountain Range in Death Valley, California, USA, seven fans formed primarily by debris flows are located adjacent to seven fans formed primarily by sheetfloods. The causal difference between these two groupings stems from their catchment lithologies; the debris flow fan catchments are clay-rich and relatively sand-poor, and the sheetflood fan catchments are clay-poor and sand-rich. On Titan, the low and mid latitudes are dominated by sand seas, demonstrating that sand is available for transport. At high latitudes, these sand seas are absent, suggesting that transportable sand is scarce. Based on the sedimentology of the two Panamint Range fan types, we hypothesize that possible fans at lower latitudes on Titan are formed by sheetfloods, whereas those at higher latitudes formed primarily by debris flows. To test these hypotheses, we measured and analyzed the mean normalized radar cross sections (σ°) and changes in σ° with downfan distance for debris flow and sheetflood fans along the Panamint Range. We then compared the results with the same measurements for possible fans on Titan. We find that, in the Panamint Range, debris flow fans are brighter than sheetflood fans and have greater change in σ° with downfan distance, and that on Titan, low-latitude possible fans are likewise brighter than the fans at high latitudes with greater change in σ° with downfan distance. Consequently, our findings suggest that low-latitude possible fans on Titan are formed primarily by debris flows, whereas high-latitude possible fans on Titan are formed primarily by sheetfloods. Thus, our results do not support our hypotheses. Scenarios to explain these results include: (1) high-latitude possible fans are dominated by radar-dark debris flow deposits, (2) low- and mid

  10. Alluvial fan response to climatic change: Insights from numerical modeling (Invited)

    Science.gov (United States)

    Pelletier, J. D.

    2009-12-01

    Alluvial fans in the western U.S. exhibit a regionally correlative sequence of Plio-Quaternary deposits. Cosmogenic and U-series dating has greatly improved the age control on these deposits and their associated terraces and generally strengthened the case for aggradation during humid-to-arid transitions. Still, the linkages between climate change, upland basin response, and alluvial fan response are not well constrained. Fans may fill and cut as a result of autogenetic processes/internal adjustments, changes in regional temperature (which controls snowmelt-induced flooding), changes in the frequency-size distribution of rainfall events, and/or changes in upslope vegetation. Here I describe the results of a numerical modeling study designed to better constrain the relationships between different end-member forcing mechanisms and the geologic record of alluvial fan deposits and terraces. The model solves the evolution of the fan topography using Exner's equation (conservation of mass) coupled with a nonlinear, threshold-controlled transport relation for sand and gravel. Bank retreat is modeled using an advection equation with a rate proportional to bank shear stress. I begin by considering the building of a fan under conditions of constant water and sediment supply. This simple system exhibits all of the complexity of fans developed under experimental conditions, and it provides insights into the mechanisms that control avulsions and it provides a baseline estimate for the within-fan relief that can result from autogenetic processes. Relationships between the magnitude and period of variations in the sediment-to-water ratio and the geomorphic response of fans are then discussed. I also consider the response of a coupled drainage basin-fan system to changes in climate, including the hydrologic and vegetation response of upland hillslopes. Fans can aggrade or incise in response to the same climatic event depending on the relief of the upstream drainage basin, which

  11. Unidad de limpieza de filtros FanCoil®

    OpenAIRE

    2010-01-01

    El objeto de éste proyecto es la definición del proceso de limpieza y el diseño de una máquina limpiadora de filtros FanCoil® para con ello dar solución a una necesidad expuesta por el Departamento de Mantenimiento de la Universidad Pública de Navarra. La máquina en cuestión constará de los elementos mecánicos, hidráulicos y eléctricos que se consideren oportunos para realizar la función deseada con las máximas garantías posibles de operatividad y seguridad. Con carácter gen...

  12. Saving energy for ventilation using decentralised duct fans

    DEFF Research Database (Denmark)

    Gunner, Amalie; Bergsøe, Niels Christian; Afshari, Alireza

    2014-01-01

    pressure drops which in turn will increase energy use. This paper presents a novel procedure for balancing CAV-systems using decentralised duct fans instead of flat plate dampers. The procedure will result in lower pressure drops and consequently in a reduction of energy use for ventilation when compared......In conventional mechanical ventilation systems with constant air volume (CAV) airflows are often balanced using balancing flat plate dampers. The purpose of the dampers is to obtain nominal airflows to the individual zones or rooms in the building. Unfortunately, this procedure leads to increased...... to a conventional mechanical ventilation system with flat plate dampers. Theoretical calculations and experimental observations for the investigated systems show that the power demand for distribution of air can be reduced about 30%. The work carried out forms part of an ongoing PhD-project on mechanical...

  13. Air Distribution in Rooms with a Fan-Driven Convector

    DEFF Research Database (Denmark)

    Larsen, Tine Steen; Bindels, Rob H.W.; Michalak, Lukasz

    2007-01-01

    Experiments with a fan-driven convector used for both heating and cooling are de.scribed in this paper. Only the cooling situation is considered. The convector is positioned in the upper corner ofthe room, and from there the cold air is let out through the device along the ceiling. The airflow...... coming from the dijfuser is partly controlled by the momentum flow and partly from gravity forces, where the thermal load in the room and the temperature difference between room air and supply air affect the airflow from the convector. The convector system was tested in the same test room in which many...... regular ventilation systems were tested earlier to be ahle to compare airflow from the convector .system with regular ventilation ,systems at a later stage of this research. The heat load in the room consists of a thermal manikin sitting at a desk, a computer, and a desk lamp producing a total heat load...

  14. Nth-powered amplitude squeezing in fan-states

    CERN Document Server

    Duc, T M

    2002-01-01

    Squeezing properties of the Hillery-type N-powered amplitude are investigated in the fan-state vertical bar xi; 2k, f> sub F which is linearly superposed by 2k 2k-quantum nonlinear coherent states in the phase-locked manner. The general expression of squeezing is derived analytically for arbitrary xi, k, N and f showing a multi-directional character of squeezing. For a given k, squeezing may appear to the even power N=2k if f ident to 1 and N>=2k if f not =1 and the number of directions along with the Nth-powered amplitude is squeezed is exactly equal to N, for both f ident to 1 (the light field) and f not =1 (the vibrational motion of the trapped ion). Discussions are also given elucidating the qualitative difference between the cases of f ident to 1 and f not =1.

  15. Functional Planning and Design of a Fan Shaped Technical Museum

    Directory of Open Access Journals (Sweden)

    Dr. Lovely K M

    2014-04-01

    Full Text Available The proposed building aims at the development of the built environment. The principal objective of this paper is the functional planning, analysis and design of a fan shaped technical museum. Technical museum is a museum that tells the stories of architecture, engineering and design. The functional planning was done according to the clauses given by Museum Building Design and Exhibition Layout: Patterns of Interactions, ICOM Code of Ethics for Museum, and Key Concepts of Museology. Plan, elevation and section were drawn in AutoCAD 2010. The design involves load calculations and analyzing the whole structure by STAAD.ProV8i. The design methods used in STAAD.ProV8i analysis are limit state design conforming to Indian Standard Code of practice. Also the building was analyzed for all possible load combinations.

  16. SPORT FAN MOTIVATION QUESTIONNAIRE: A STUDY OF VALIDITY AND RELIABILITY

    Directory of Open Access Journals (Sweden)

    Muhammed Emin KAFKAS

    2012-04-01

    Full Text Available The purpose of this research, Yousof Al-Thibiti (2004 Fan Motivational scale was developed by Turkish adapts and scales to analyze the validity and reliability. The study group was composed that Inonu University studying at different faculty of education between the age of 17-31 494’ü (%54 women and 421’i (%46 male students. Firstly of linguistic equivalence of the scale were examined. Secondly after linguistic equivalence was performed reliability analysis. The total scale internal consistency coefficients for sizes .85 and subscale range of .70-.78, the re-test reliability coefficients were between .79-.89. at the same time, exploratory factor analysis and confirmatory factor analysis is carried out with the scale and found to comply with the data. As a result of scale to measure the status of individuals to participate in sporting activities was found to have an appropriate structure.

  17. A simplified fragility analysis of fan type cable stayed bridges

    Institute of Scientific and Technical Information of China (English)

    R. A. Khan; T. K. Datta; S. Ahmad

    2005-01-01

    A simplified fragility analysis of fan type cable stayed bridges using Probabilistic Risk Analysis (PRA)procedure is presented for determining their failure probability under random ground motion. Seismic input to the bridge support is considered to be a risk consistent response spectrum which is obtained from a separate analysis. For the response analysis, the bridge deck is modeled as a beam supported on springs at different points. The stiffnesses of the springs are determined by a separate 2D static analysis of cable-tower-deck system. The analysis provides a coupled stiffness matrix for the spring system. A continuum method of analysis using dynamic stiffness is used to determine the dynamic properties of the bridges .The response of the bridge deck is obtained by the response spectrum method of analysis as applied to multidegree of freedom system which duly takes into account the quasi - static component of bridge deck vibration. The fragility analysis includes uncertainties arising due to the variation in ground motion, material property, modeling, method of analysis,ductility factor and damage concentration effect. Probability of failure of the bridge deck is determined by the First Order Second Moment (FOSM) method of reliability. A three span double plane symmetrical fan type cable stayed bridge of total span 689 m, is used as an illustrative example. The fragility curves for the bridge deck failure are obtained under a number of parametric variations. Some of the important conclusions of the study indicate that (i) not only vertical component but also the horizontal component of ground motion has considerable effect on the probability of failure; (ii) ground motion with no time lag between support excitations provides a smaller probability of failure as compared to ground motion with very large time lag between support excitation; and (iii) probability of failure may considerably increase for soft soil condition.

  18. Antidiabetic oils.

    Science.gov (United States)

    Berraaouan, Ali; Abid, Sanae; Bnouham, Mohamed

    2013-11-01

    Many studies have demonstrated evidence of the health benefits of natural products. Plant extracts have been tested on a variety of physiological disorders, including diabetes mellitus. Studies have tested aqueous extracts, plant fractions extracts, families of active of compounds, and specific active compounds. In this review, we describe the antidiabetic effects of vegetable oils. Information was collected from ScienceDirect and PubMed databases using the following key words: Diabetes mellitus, Oils, Vegetable oils, Type 1 diabetes, type 2 diabetes, antidiabetic effect, antihyperglycemic, antidiabetic oil. We have compiled approximately ten vegetable oils with including experimental studies that have demonstrated benefits on diabetes mellitus. There are soybean, argan, olive, palm, walnut, black cumin, safflower, Colocynth, Black seed, Rice bran, Cinnamom, and Rocket oils. For each vegetable oil, we investigated on the plant's traditional uses, their pharmacological activities and their antidiabetic effects. It seems that many vegetable oils are really interesting and can be used in the improvement of human health, particularly, to prevent or to treat diabetes mellitus complications.

  19. Coconut Oil

    Science.gov (United States)

    ... immune system. Despite coconut oil's high calorie and saturated fat content, some people use it by mouth to ... Coconut oil is high in a saturated fat called medium chain triglycerides. These fats work differently than other types of saturated fat in the body. However, research on the effects ...

  20. Release of Crude Oil from Silica and Calcium Carbonate Surfaces

    DEFF Research Database (Denmark)

    Liu, Xiaoyan; Yan, Wei; Stenby, Erling Halfdan;

    2016-01-01

    Adsorption and desorption of a North Sea crude oil to silica and calcium carbonate surfaces were studied by a quartz crystal microbalance, while the bare surfaces and adsorbed oil layers were characterized by atomic force microscopy and contact angle measurements. Water contact angles were measured...... on the bare surfaces, surfaces with an adsorbed oil layer, and surfaces after being exposed to aqueous salt solutions. This showed that the silica surface became more hydrophobic after oil adsorption, while the wettability of the calcium carbonate surface was not significantly changed by adsorption of an oil...... layer. A surface energy component analysis based on the acid base theory showed that oil adsorption on the surfaces depends upon apolar, acidic, and basic oil components of the crude oil and that the adsorbed oil components differ for adsorption to silica and calcium carbonate. Desorption of the crude...

  1. Atomic phase diagram

    Institute of Scientific and Technical Information of China (English)

    LI Shichun

    2004-01-01

    Based on the Thomas-Fermi-Dirac-Cheng model, atomic phase diagram or electron density versus atomic radius diagram describing the interaction properties of atoms of different kinds in equilibrium state is developed. Atomic phase diagram is established based on the two-atoms model. Besides atomic radius, electron density and continuity condition for electron density on interfaces between atoms, the lever law of atomic phase diagram involving other physical parameters is taken into account, such as the binding energy, for the sake of simplicity.

  2. Sedimentology and clast fabric of subaerial debris flow facies in a glacially-influenced alluvial fan

    Science.gov (United States)

    Eyles, N.; Kocsis, S.

    1988-09-01

    A large alluvial fan (2 km 2), constructed between 11,000 and 7000 years B.P. at the mouth of Cinquefoil Creek in interior British Columbia, Canada, is identified as "glacially-influenced, debris flow-dominated". The fan was rapidly constructed during and immediately after deglaciation when large volumes of glacial debris were resedimented downslope; fans of this type are widespread in the glaciated portion of the North American Cordillera. Diamict facies, deposited as debris flows, account for 48% of the fan volume, sheetflodd gravels 37%, and other facies 15%. Diamicts show three facies types; crudely-bedded facies containing rafts of soft sediment that are attributed to downslope collapse and mixing of heterogeneous glacial deposits. These occur within the core of the fan. Massive and weakly graded (inverse to normal) diamict facies, derived from the downslope flow of weathered volcanic bedrock, occur within a well-defined bed that can be traced across the entire fan. The occurrence of weakly graded facies as lateral equivalents to massive facies within the same bed, implies the partial development of turbulent, high-velocity "streams" within a viscous debris flow moving over a slope of 6°. Clast fabrics in these facies show weakly-clustered a-axes dipping up and downslope comparable to other debris flows and lahars. The Cinquefoil fan, its internal structure and facies, provides a good "modern" analogue for ancient diamictite sequences deposited in areas of active uplift, rifting and glaciation.

  3. Fan type end moraine related glaciofluvial deposits of Last Glaciation from Lithuania

    Science.gov (United States)

    Šinkūnė, Eglė; Šinkūnas, Petras

    2015-04-01

    Several alluvial-fan type end moraine related sites were chosen for detailed sedimentological analyses in ice marginal zone of the last glaciation in Lithuania. Such glaciofluvial ice-marginal fans are formed close to linear ice-sheet front and have semi-conical form or represent simple asymmetric hill forms or more complex ridges with steep proximal and gentler distal slopes. Sedimentary sequences of ice-marginal fans studied consist mainly of waterlain sandy and gravelly deposits with pebbles and boulders. In some sequences a debris-flow deposits are observed as well as beds of sorted material interbedded with dominating high energy sheetflow deposits. Sediment grain size, sorting, structure and bedding characteristics dependent on ice proximity and hydrodynamic conditions were analysed. Highly pulsatory water discharge can be interpreted from depositional architecture of the end moraine related fans. The inferred character of sedimentation suggests that landforms consisting of deposits studied are genetically similar to the alluvial fans. According to the sedimentation features the investigated landforms are an intermediate between the marginal glaciofluvial ridges and sandur fans. Are they a transition zone of sedimentation between the end moraines and proximal outwash plains, or can be the end moraine related fans distinguished as a separate type of glaciofluvial deposits? This question is still open.

  4. Development of a Solar Powered Standing Dc Fan Using Three Phase

    Directory of Open Access Journals (Sweden)

    Musa B. Ibrahim

    2016-12-01

    Full Text Available A solar powered standing dc fan is a small, portable type of fan that is used in various rooms of home or office. It is more convenient compared to other types, like kitchen exhaust, window, and pedestal fans because of its portability. It serves a number of functions for home owners and office workers such as conservation of energy, removal of heat and unwanted fumes from indoor areas, cooling a room and generation of Mechanical noise that helps to distract a person's attention from undesirable background noise so one could focus on his task. The idea of a solar fan has been proven to be very good especially for a country like Nigeria that enjoys an average of 8 hours of sunlight daily. In this research a 3-blade standing fan of 30 watts capacity capable of providing 6 hours of continuous operation was powered with just 1 photo-voltaic (PV module of 80 watts power rating. Also a minimum of 85% efficiency was achieved and the fan runs at a low torque of 0.95 Nm. The fan blade rotates at a tip speed of 500 rpm and rotates on a 100 mm diameter shaft. In order to maintain constant operation during the night and when the sun is not at its peak, a 75Ah, 12V battery has been considered suitable for the power storage assessor

  5. Fan Noise Source Diagnostic Test Computation of Rotor Wake Turbulence Noise

    Science.gov (United States)

    Nallasamy, M.; Envia, E.; Thorp, S. A.; Shabbir, A.

    2002-01-01

    An important source mechanism of fan broadband noise is the interaction of rotor wake turbulence with the fan outlet guide vanes. A broadband noise model that utilizes computed rotor flow turbulence from a RANS code is used to predict fan broadband noise spectra. The noise model is employed to examine the broadband noise characteristics of the 22-inch Source Diagnostic Test fan rig for which broadband noise data were obtained in wind tunnel tests at the NASA Glenn Research Center. A 9-case matrix of three outlet guide vane configurations at three representative fan tip speeds are considered. For all cases inlet and exhaust acoustic power spectra are computed and compared with the measured spectra where possible. In general, the acoustic power levels and shape of the predicted spectra are in good agreement with the measured data. The predicted spectra show the experimentally observed trends with fan tip speed, vane count, and vane sweep. The results also demonstrate the validity of using CFD-based turbulence information for fan broadband noise calculations.

  6. Fan activism, cybervigilantism, and Othering mechanisms in K-pop fandom

    Directory of Open Access Journals (Sweden)

    Sun Jung

    2012-06-01

    Full Text Available Korean popular music (K-pop fandom may serve as a case study to identify both cynical and utopian views of fans' participatory Net activism by addressing three key aspects: fan activism, cybervigilantism, and Othering mechanisms. Fancom (fan company in the K-pop scene refers to the way fans systematically manage their own stars. These notions of assertive fancom practices address how fans actively participate in sociocultural events such as fund raising, donating to charity, and volunteering in emergency situations. This management may take another turn, however: antifandom surrounds K-pop star Tablo, signifying cybervigilantism of sinsang teolgi (personal information theft, a term referring to the online activities of a group of netizens who seek to expose the personal details of perceived wrongdoers by publishing them online as a form of punishment. The Tablo case revitalized public concern over privacy and the security of personal information in the digital era. Finally, Othering mechanisms in participatory online K-pop fandom display a strong sense of nationalism and even racism, as demonstrated by responses to anti-Korean rhetoric posted on the MySpace page of K-pop idol Jae-Beom. This highlights the relationship between participatory Net activism and nationalistic sentiment active within K-pop fandom. Some K-pop fan practices may have negative connotations, but by engaging with specific civic issues and social events, participatory fan practices encourage people to interact, discuss, and challenge conventional discourses, which may lead to new forms of social action.

  7. Measurement and analysis of radiated sound from a low speed fan with a large tip gap.

    Science.gov (United States)

    Bilka, M J; Anthoine, J; Schram, C

    2014-05-01

    The wake flow field and radiated sound from a low speed axial fan is studied experimentally. The fan geometry uses controlled diffusion blades and is designed with a low aspect ratio (0.9). The fan is installed with a large tip gap, approximately 10% of the blade span. The radiated sound field is analyzed using a known trailing edge noise formulation. First, the model is compared to an experiment of a single airfoil in a wind tunnel to assess the predictive capabilities. Second, measurements of the fan are made at two different blade loading conditions. Hot wire measurements are made in the near wake of the fan to assess the extent of the tip leakage flow for each condition. The radiated sound fields are compared with the trailing edge noise theory. Use is made of the wake measurements as an input to a surface pressure model. When the fan is operated with the optimal blade loading, the influence of the tip leakage flow is found to be of secondary acoustic impact. When the fan is operated at a high loading condition for the blades, a more significant leakage flow develops and is found to be responsible for the dominant radiated sound.

  8. Low-pressure reversible axial fan with straight profile blades and relatively high efficiency

    Directory of Open Access Journals (Sweden)

    Spasić Živan T.

    2012-01-01

    Full Text Available The paper presents the design and operating characteristics of a model of reversible axial fan with only one impeller, whose reversibility is achieved by changing the direction of rotation. The fan is designed for the purpose of providing alternating air circulation in wood dryers in order to reduce the consumption of electricity for the fan and increase energy efficiency of the entire dryer. To satisfy the reversibility of flow, the shape of the blade profile is symmetrical along the longitudinal and transversal axes of the profile. The fan is designed with equal specific work of all elementary stages, using the method of lift forces. The impeller blades have straight mean line profiles. The shape of the blade profile was adopted after the numerical simulations were carried out and high efficiency was achieved. Based on the calculation and conducted numerical simulations, a physical model of the fan was created and tested on a standard test rig, with air loading at the suction side of the fan. The operating characteristics are shown for different blade angles. The obtained maximum efficiency was around 0.65, which represents a rather high value for axial fans with straight profile blades.

  9. Flow performance of highly loaded axial fan with bowed rotor blades

    Science.gov (United States)

    Chen, L.; Liu, X. J.; Yang, A. L.; Dai, R.

    2013-12-01

    In this paper, a partial bowed rotor blade was proposed for a newly designed high loaded axial fan. The blade was positively bowed 30 degrees from hub to 30 percent spanwise position. Flows of radial blade and bowed blade fans were numerically compared for various operation conditions. Results show that the fan's performance is improved. At the designed condition with flow coefficient of 0.52, the efficiency of the bowed blade fan is increased 1.44% and the static pressure rise is increased 11%. Comparing the flow structures, it can be found that the separated flow in the bowed fan is reduced and confined within 20 percent span, which is less than the 35 percent in the radial fan. It means that the bowed blade generates negative blade force and counteracts partial centrifugal force. It is alleviates the radial movements of boundary layers in fan's hub region. Flow losses due to 3D mixing are reduced in the rotor. Inlet flow to downstream stator is also improved.

  10. Traditional transformations and transmedial affirmations: Blurring the boundaries of Sherlockian fan practices

    Directory of Open Access Journals (Sweden)

    Ashley D. Polasek

    2017-03-01

    Full Text Available The modes of discourse employed by fans of Sherlock Holmes represent both affirmational and transformational impulses. As the fan community has grown and diversified, tensions have arisen between Sherlockians who prefer to utilize traditional frameworks dating back to the early practices of the Baker Street Irregulars in the 1930s and '40s and those who operate primarily in virtual spaces and utilize 21st-century digital platforms as frameworks for their discourse. Because the demographics of affirmational fans tend to align with those of fans preferring traditional frameworks, and conversely, the demographics of transformational fans tend to align with those of fans preferring transmedial frameworks, the styles of engagement often become conflated with the impulses driving the discourse itself. By first examining these tensions and then utilizing case studies that illustrate the four combinations of frameworks and modes of discourse—traditional-affirmational, transmedial-affirmational, traditional-transformational, and transmedial-transformational—I seek to complicate the boundaries that appear to divide the larger Sherlock Holmes fan community. I will demonstrate that the twin fannish impulses to affirm the text and transform it have operated not at odds but in parallel throughout the history of the fandom.

  11. An inventory and risk-based prioritization of Steep Creek Fans in Alberta, Canada

    Directory of Open Access Journals (Sweden)

    Holm Kris

    2016-01-01

    Full Text Available In June 2013, heavy rainfall caused flooding on most rivers in the province of Alberta, Canada, producing one of Canada’s most expensive natural disasters with about $6 billion (CDN in damage. Flooding inundated several municipalities including downtown Calgary, the fourth-largest city in Canada. Debris flows and debris floods caused extensive highway closures and damages to development on alluvial fans. Following these events, the Government of Alberta requested an inventory of all fans intersecting municipal development, major roads and highways in Alberta. Such fans may be subject to debris flow, debris flood (mud flows, and/or flood hazards. The study area spans the entirety of the Alberta Rocky Mountains, approximately 51,000 km2 (7% of Alberta. We characterize 710 fans in terms of hazard level and presence and types of elements at risk. We statistically analyse watershed attributes to predict the dominant fan hydrogeomorphic process types. All fans under provincial jurisdiction are assigned priority ratings based on hazard levels and the presence and value of elements at risk. The prioritization is risk-based as it considers both hazards and potential consequences. Of the fans prioritized, 13% intersected parcels containing land and residential developments with an assessed value of $2.4 billion (CDN, and the remainder were crossed by roads, pipelines or transmission lines. We present the study results on an interactive, searchable web application that can support ongoing hazard and risk assessments and risk reduction planning.

  12. RESEARCH ON DESIGN METHODOLOGY OF SMALL AXIAL FAN ‐CONSIDERATION OF INLET FLOW VELOCITY FOR PERFORMANCE ENHANCEMENT‐

    OpenAIRE

    2013-01-01

    The efficiency of small axial fan used as cooling device in information technology machines is extremely low, comparing with conventional axial fan which is much larger than small fan. In the design of conventional axial fan, the axial velocity of the inlet flow is regarded as uniform along the blade span. However, in case of the small fan, the velocity could not be uniform.Because the hub-tip ratiois so large that the blade span will be too short to keep the uniform flow region. So, it is im...

  13. Flow Characteristics of the Sound Pressure Level and its Prediction for a Low Pressure Axial Flow Fan

    OpenAIRE

    1987-01-01

    The relation between the noise level of an axial flow fan and the flow around the fan rotor was investigated over a wide range of fan flow rates. The magnitude of the wake width in the region where the velocity of air relative to the blade is large controls the noise level. The change in the noise level with fan flow rate can be estimated by a working formula proposed by the present authors for predicting the noise level of a fan working at its design point.

  14. INFLUENCE OF APPLYING ADDITIONAL FORCING FANS FOR THE AIR DISTRIBUTION IN VENTILATION NETWORK

    Directory of Open Access Journals (Sweden)

    Nikodem SZLĄZAK

    2016-07-01

    Full Text Available Mining progress in underground mines cause the ongoing movement of working areas. Consequently, it becomes neces-sary to adapt the ventilation network of a mine to direct airflow into newly-opened districts. For economic reasons, opening new fields is often achieved via underground workings. Length of primary intake and return routes increases and also increases the total resistance of a complex ventilation network. The development of a subsurface structure can make it necessary to change the air distribution in a ventilation network. Increasing airflow into newly-opened districts is necessary. In mines where extraction does not entail gas-related hazards, there is possibility of implementing a push-pull ventilation system in order to supplement airflows to newly developed mining fields. This is achieved by installing sub-surface fan stations with forcing fans at the bottom of downcast shaft. In push-pull systems with multiple main fans, it is vital to select forcing fans with characteristic curves matching those of the existing exhaust fans to prevent undesirable mutual interaction. In complex ventilation networks it is necessary to calculate distribution of airflow (especially in net-works with a large number of installed fans. In the article the influence of applying additional forcing fans for the air distribution in ventilation network for underground mine were considered. There are also analysed the extent of over-pressure caused by the additional forcing fan in branches of the ventilation network (the operating range of additional forcing fan. Possibilities of increasing airflow rate in working areas were conducted.

  15. Cold Matter Assembled Atom-by-Atom

    CERN Document Server

    Endres, Manuel; Keesling, Alexander; Levine, Harry; Anschuetz, Eric R; Krajenbrink, Alexandre; Senko, Crystal; Vuletic, Vladan; Greiner, Markus; Lukin, Mikhail D

    2016-01-01

    The realization of large-scale fully controllable quantum systems is an exciting frontier in modern physical science. We use atom-by-atom assembly to implement a novel platform for the deterministic preparation of regular arrays of individually controlled cold atoms. In our approach, a measurement and feedback procedure eliminates the entropy associated with probabilistic trap occupation and results in defect-free arrays of over 50 atoms in less than 400 ms. The technique is based on fast, real-time control of 100 optical tweezers, which we use to arrange atoms in desired geometric patterns and to maintain these configurations by replacing lost atoms with surplus atoms from a reservoir. This bottom-up approach enables controlled engineering of scalable many-body systems for quantum information processing, quantum simulations, and precision measurements.

  16. Where program and fantasy meet: Female fans conversing with character bots in Japan [symposium

    Directory of Open Access Journals (Sweden)

    Keiko Nishimura

    2013-03-01

    Full Text Available Character bots are automated programs that post—that is, tweet—characters' lines from popular manga, anime, games, and so on. They post regularly, and in the past few years they have become difficult to ignore, especially in fan communities. Many fans take great pleasure in interacting with favorite characters as bots; rhey also enjoy the communities that spring up around favorite series, characters, and, yes, even bots. Here I adopt an ethnographic approach to analyze the human dimensions of the phenomenon of character bots, based on participant observation among female fans in Japan.

  17. Climatic and Tectonic Controls on Alluvial Fan Evolution: The Lost River Range, Idaho

    Science.gov (United States)

    Phillips, R. J.; Pierce, J. L.; Sharp, W. D.; Pierce, K. L.

    2006-12-01

    In the northern Basin &Range, alluvial fans developed along the Lost River range-front consist of several distinct inset fan segments with concave-up radial profiles. Multiple large radius (>5 km), shallow (2- 3°), alluvial fans extend across and beyond the active, ~140-km-long, normal Lost River fault. These large fans are relict features, formed by major sheetfloods that occurred intermittently between ~15-180 ka. More recent deposition has been dominated by debris-flows that form small-radius (cuts through gravelly fan deposits, indicates that the fan soils are geochemically suitable for uranium-series dating (median U=7ppm, 232Th=0.09ppm, 232Th/230Th=154). 230Th/U analysis of these calcic soils can thus provide precise temporal constraints on intervals of surface stability and subsequent soil formation. The oldest fan surface (Qfo1, 178+/-8 ka), exposed within the footwall of the trench, suggests an interval of surface stability, indicating that the fan was likely abandoned due to incision early in MIS 6. Incision may have resulted from surface faulting along the Arco segment of the Lost River fault, but could relate to changes in stream power or sediment supply associated with climatic change or with auto-cyclic variations within the drainage basin. A younger incised and faulted fan surface (Qfo2, 69+/-6 ka), likely represents active alluviation at the beginning of MIS 4 and, since it formed as hanging-wall alluvial gravel, provides age limits on an episode of fault displacement between Qfo1 and Qfo2. In situ pedogenic carbonate coats on sub-angular gravels within the colluvial fault wedge date at 68+/-2 ka, suggesting that either faulting occurred soon after Qfo2 stabilized or that soil carbonate coats were recycled into the colluvial wedge from the faulted surface. Further studies in the Lost River Range will assess the timing of fan deposition, surface stabilization and fault activity since the late Pleistocene using coupled application of Optically

  18. Development of a Solar Powered Standing Dc Fan Using Three Phase

    OpenAIRE

    Musa B. Ibrahim; Auwal Mohammed; Haruna Abubakar

    2016-01-01

    A solar powered standing dc fan is a small, portable type of fan that is used in various rooms of home or office. It is more convenient compared to other types, like kitchen exhaust, window, and pedestal fans because of its portability. It serves a number of functions for home owners and office workers such as conservation of energy, removal of heat and unwanted fumes from indoor areas, cooling a room and generation of Mechanical noise that helps to distract a person's attention from undesira...

  19. Measurement of unsteady surface pressure on rotor blades of fans by pressure-sensitive paint

    Science.gov (United States)

    Yokoyama, Hiroshi; Miura, Kouhei; Iida, Akiyoshi

    2017-01-01

    To clarify the unsteady pressure distributions on the rotor blades of an axial fan, a pressure-sensitive paint (PSP) technique was used. To capture the image of the rotating fan as a static image, an optical derotator method with a dove prism was adopted. It was confirmed by preliminary experiments with a resonator and a speaker that the pressure fluctuations with 347 Hz can be measured by the present PSP. The measured mean pressure distributions were compared with the predicted results based on large-eddy simulations. The measured instantaneous surface pressure is instrumental to identify acoustic source of fan noise in the design stage.

  20. A comparative study of varying fan noise mitigation techniques in relation to sustainable design goals

    Science.gov (United States)

    Overweg, Cornelis; Fullerton, Jeff L.

    2005-04-01

    Green building design promotes effective use of materials and energy, improved indoor environmental quality (IEQ), and enhanced occupant comfort. These ``green'' goals can occasionally conflict with common acoustical approaches used for fan noise control. A design striving for low noise levels from the ventilation system to benefit occupant comfort can inadvertently introduce elements that are contradictory to other green building objectives. For example, typical fan noise control devices introduce higher energy consumption or less beneficial indoor environmental quality. This paper discusses the acoustical, mechanical, environmental, and relative cost impacts of various fan noise control techniques.