WorldWideScience

Sample records for factorial split-plot designs

  1. Constructing General Orthogonal Fractional Factorial Split-Plot Designs

    NARCIS (Netherlands)

    Sartono, B.; Goos, P.; Schoen, E.

    2015-01-01

    While the orthogonal design of split-plot fractional factorial experiments has received much attention already, there are still major voids in the literature. First, designs with one or more factors acting at more than two levels have not yet been considered. Second, published work on nonregular

  2. Split-plot fractional designs: Is minimum aberration enough?

    DEFF Research Database (Denmark)

    Kulahci, Murat; Ramirez, Jose; Tobias, Randy

    2006-01-01

    Split-plot experiments are commonly used in industry for product and process improvement. Recent articles on designing split-plot experiments concentrate on minimum aberration as the design criterion. Minimum aberration has been criticized as a design criterion for completely randomized fractional...... factorial design and alternative criteria, such as the maximum number of clear two-factor interactions, are suggested (Wu and Hamada (2000)). The need for alternatives to minimum aberration is even more acute for split-plot designs. In a standard split-plot design, there are several types of two...... for completely randomized designs. Consequently, we provide a modified version of the maximum number of clear two-factor interactions design criterion to be used for split-plot designs....

  3. Estimation of Missing Observations in Two-Level Split-Plot Designs

    DEFF Research Database (Denmark)

    Almimi, Ashraf A.; Kulahci, Murat; Montgomery, Douglas C.

    2008-01-01

    Inserting estimates for the missing observations from split-plot designs restores their balanced or orthogonal structure and alleviates the difficulties in the statistical analysis. In this article, we extend a method due to Draper and Stoneman to estimate the missing observations from unreplicated...... two-level factorial and fractional factorial split-plot (FSP and FFSP) designs. The missing observations, which can either be from the same whole plot, from different whole plots, or comprise entire whole plots, are estimated by equating to zero a number of specific contrast columns equal...... to the number of the missing observations. These estimates are inserted into the design table and the estimates for the remaining effects (or alias chains of effects as the case with FFSP designs) are plotted on two half-normal plots: one for the whole-plot effects and the other for the subplot effects...

  4. Designing fractional factorial split-plot experiments using integer programming

    DEFF Research Database (Denmark)

    Capehart, Shay R.; Keha, Ahmet; Kulahci, Murat

    2011-01-01

    factorial (FF) design, with the restricted randomisation structure to account for the whole plots and subplots. We discuss the formulation of FFSP designs using integer programming (IP) to achieve various design criteria. We specifically look at the maximum number of clear two-factor interactions...

  5. Multi-reader ROC studies with split-plot designs: a comparison of statistical methods.

    Science.gov (United States)

    Obuchowski, Nancy A; Gallas, Brandon D; Hillis, Stephen L

    2012-12-01

    Multireader imaging trials often use a factorial design, in which study patients undergo testing with all imaging modalities and readers interpret the results of all tests for all patients. A drawback of this design is the large number of interpretations required of each reader. Split-plot designs have been proposed as an alternative, in which one or a subset of readers interprets all images of a sample of patients, while other readers interpret the images of other samples of patients. In this paper, the authors compare three methods of analysis for the split-plot design. Three statistical methods are presented: the Obuchowski-Rockette method modified for the split-plot design, a newly proposed marginal-mean analysis-of-variance approach, and an extension of the three-sample U-statistic method. A simulation study using the Roe-Metz model was performed to compare the type I error rate, power, and confidence interval coverage of the three test statistics. The type I error rates for all three methods are close to the nominal level but tend to be slightly conservative. The statistical power is nearly identical for the three methods. The coverage of 95% confidence intervals falls close to the nominal coverage for small and large sample sizes. The split-plot multireader, multicase study design can be statistically efficient compared to the factorial design, reducing the number of interpretations required per reader. Three methods of analysis, shown to have nominal type I error rates, similar power, and nominal confidence interval coverage, are available for this study design. Copyright © 2012 AUR. All rights reserved.

  6. Split-plot designs for robotic serial dilution assays.

    Science.gov (United States)

    Buzas, Jeffrey S; Wager, Carrie G; Lansky, David M

    2011-12-01

    This article explores effective implementation of split-plot designs in serial dilution bioassay using robots. We show that the shortest path for a robot to fill plate wells for a split-plot design is equivalent to the shortest common supersequence problem in combinatorics. We develop an algorithm for finding the shortest common supersequence, provide an R implementation, and explore the distribution of the number of steps required to implement split-plot designs for bioassay through simulation. We also show how to construct collections of split plots that can be filled in a minimal number of steps, thereby demonstrating that split-plot designs can be implemented with nearly the same effort as strip-plot designs. Finally, we provide guidelines for modeling data that result from these designs. © 2011, The International Biometric Society.

  7. Split-plot designs for multistage experimentation

    DEFF Research Database (Denmark)

    Kulahci, Murat; Tyssedal, John

    2016-01-01

    at the same time will be more efficient. However, there have been only a few attempts in the literature to provide an adequate and easy-to-use approach for this problem. In this paper, we present a novel methodology for constructing two-level split-plot and multistage experiments. The methodology is based...... be accommodated in each stage. Furthermore, split-plot designs for multistage experiments with good projective properties are also provided....

  8. The Use of Plackett-Burman Designs to Construct Split Plot Designs.

    NARCIS (Netherlands)

    Kulahci, M.; Bisgaard, S.

    2005-01-01

    Abstract When some factors are hard to change and others are relatively easier, split-plot experiments are often an economic alternative to fully randomized designs. Split-plot experiments, with their structure of subplot arrays imbedded within whole-plot arrays, have a tendency to become large,

  9. Checking the Adequacy of Fit of Models from Split-Plot Designs

    DEFF Research Database (Denmark)

    Almini, A. A.; Kulahci, Murat; Montgomery, D. C.

    2009-01-01

    models. In this article, we propose the computation of two R-2, R-2-adjusted, prediction error sums of squares (PRESS), and R-2-prediction statistics to measure the adequacy of fit for the WP and the SP submodels in a split-plot design. This is complemented with the graphical analysis of the two types......One of the main features that distinguish split-plot experiments from other experiments is that they involve two types of experimental errors: the whole-plot (WP) error and the subplot (SP) error. Taking this into consideration is very important when computing measures of adequacy of fit for split-plot...... of errors to check for any violation of the underlying assumptions and the adequacy of fit of split-plot models. Using examples, we show how computing two measures of model adequacy of fit for each split-plot design model is appropriate and useful as they reveal whether the correct WP and SP effects have...

  10. Split-Plot Designs with Mirror Image Pairs as Subplots

    DEFF Research Database (Denmark)

    Tyssedal, John; Kulahci, Murat; Bisgaard, Soren

    2011-01-01

    In this article we investigate two-level split-plot designs where the sub-plots consist of only two mirror image trials. Assuming third and higher order interactions negligible, we show that these designs divide the estimated effects into two orthogonal sub-spaces, separating sub-plot main effects...... appealing with effects of major interest free from full aliasing assuming that 3rd and higher order interactions are negligible....

  11. Paired split-plot designs of multireader multicase studies.

    Science.gov (United States)

    Chen, Weijie; Gong, Qi; Gallas, Brandon D

    2018-07-01

    The widely used multireader multicase ROC study design for comparing imaging modalities is the fully crossed (FC) design: every reader reads every case of both modalities. We investigate paired split-plot (PSP) designs that may allow for reduced cost and increased flexibility compared with the FC design. In the PSP design, case images from two modalities are read by the same readers, thereby the readings are paired across modalities. However, within each modality, not every reader reads every case. Instead, both the readers and the cases are partitioned into a fixed number of groups and each group of readers reads its own group of cases-a split-plot design. Using a [Formula: see text]-statistic based variance analysis for AUC (i.e., area under the ROC curve), we show analytically that precision can be gained by the PSP design as compared with the FC design with the same number of readers and readings. Equivalently, we show that the PSP design can achieve the same statistical power as the FC design with a reduced number of readings. The trade-off for the increased precision in the PSP design is the cost of collecting a larger number of truth-verified patient cases than the FC design. This means that one can trade-off between different sources of cost and choose a least burdensome design. We provide a validation study to show the iMRMC software can be reliably used for analyzing data from both FC and PSP designs. Finally, we demonstrate the advantages of the PSP design with a reader study comparing full-field digital mammography with screen-film mammography.

  12. Trellis plots as visual aids for analyzing split plot experiments

    DEFF Research Database (Denmark)

    Kulahci, Murat; Menon, Anil

    2017-01-01

    The analysis of split plot experiments can be challenging due to a complicated error structure resulting from restrictions on complete randomization. Similarly, standard visualization methods do not provide the insight practitioners desire to understand the data, think of explanations, generate...... hypotheses, build models, or decide on next steps. This article demonstrates the effective use of trellis plots in the preliminary data analysis for split plot experiments to address this problem. Trellis displays help to visualize multivariate data by allowing for conditioning in a general way. They can...

  13. Analysis of a Split-Plot Experimental Design Applied to a Low-Speed Wind Tunnel Investigation

    Science.gov (United States)

    Erickson, Gary E.

    2013-01-01

    A procedure to analyze a split-plot experimental design featuring two input factors, two levels of randomization, and two error structures in a low-speed wind tunnel investigation of a small-scale model of a fighter airplane configuration is described in this report. Standard commercially-available statistical software was used to analyze the test results obtained in a randomization-restricted environment often encountered in wind tunnel testing. The input factors were differential horizontal stabilizer incidence and the angle of attack. The response variables were the aerodynamic coefficients of lift, drag, and pitching moment. Using split-plot terminology, the whole plot, or difficult-to-change, factor was the differential horizontal stabilizer incidence, and the subplot, or easy-to-change, factor was the angle of attack. The whole plot and subplot factors were both tested at three levels. Degrees of freedom for the whole plot error were provided by replication in the form of three blocks, or replicates, which were intended to simulate three consecutive days of wind tunnel facility operation. The analysis was conducted in three stages, which yielded the estimated mean squares, multiple regression function coefficients, and corresponding tests of significance for all individual terms at the whole plot and subplot levels for the three aerodynamic response variables. The estimated regression functions included main effects and two-factor interaction for the lift coefficient, main effects, two-factor interaction, and quadratic effects for the drag coefficient, and only main effects for the pitching moment coefficient.

  14. Split-plot Experiments with Unusual Numbers of Subplot Runs

    DEFF Research Database (Denmark)

    Kulahci, Murat

    2007-01-01

    In many experimental situations, it may not be feasible or even possible to run experiments in a completely randomized fashion as usually recommended. Under these circumstances, split-plot experiments in which certain factors are changed less frequently than the others are often used. Most...

  15. Mixed-strain housing for female C57BL/6, DBA/2, and BALB/c mice: validating a split-plot design that promotes refinement and reduction.

    Science.gov (United States)

    Walker, Michael; Fureix, Carole; Palme, Rupert; Newman, Jonathan A; Ahloy Dallaire, Jamie; Mason, Georgia

    2016-01-27

    Inefficient experimental designs are common in animal-based biomedical research, wasting resources and potentially leading to unreplicable results. Here we illustrate the intrinsic statistical power of split-plot designs, wherein three or more sub-units (e.g. individual subjects) differing in a variable of interest (e.g. genotype) share an experimental unit (e.g. a cage or litter) to which a treatment is applied (e.g. a drug, diet, or cage manipulation). We also empirically validate one example of such a design, mixing different mouse strains -- C57BL/6, DBA/2, and BALB/c -- within cages varying in degree of enrichment. As well as boosting statistical power, no other manipulations are needed for individual identification if co-housed strains are differentially pigmented, so also sparing mice from stressful marking procedures. The validation involved housing 240 females from weaning to 5 months of age in single- or mixed- strain trios, in cages allocated to enriched or standard treatments. Mice were screened for a range of 26 commonly-measured behavioural, physiological and haematological variables. Living in mixed-strain trios did not compromise mouse welfare (assessed via corticosterone metabolite output, stereotypic behaviour, signs of aggression, and other variables). It also did not alter the direction or magnitude of any strain- or enrichment-typical difference across the 26 measured variables, or increase variance in the data: indeed variance was significantly decreased by mixed- strain housing. Furthermore, using Monte Carlo simulations to quantify the statistical power benefits of this approach over a conventional design demonstrated that for our effect sizes, the split- plot design would require significantly fewer mice (under half in most cases) to achieve a power of 80%. Mixed-strain housing allows several strains to be tested at once, and potentially refines traditional marking practices for research mice. Furthermore, it dramatically illustrates the

  16. Mixed-strain housing for female C57BL/6, DBA/2, and BALB/c mice: validating a split-plot design that promotes refinement and reduction

    Directory of Open Access Journals (Sweden)

    Michael Walker

    2016-01-01

    Full Text Available Abstract Background Inefficient experimental designs are common in animal-based biomedical research, wasting resources and potentially leading to unreplicable results. Here we illustrate the intrinsic statistical power of split-plot designs, wherein three or more sub-units (e.g. individual subjects differing in a variable of interest (e.g. genotype share an experimental unit (e.g. a cage or litter to which a treatment is applied (e.g. a drug, diet, or cage manipulation. We also empirically validate one example of such a design, mixing different mouse strains -- C57BL/6, DBA/2, and BALB/c -- within cages varying in degree of enrichment. As well as boosting statistical power, no other manipulations are needed for individual identification if co-housed strains are differentially pigmented, so also sparing mice from stressful marking procedures. Methods The validation involved housing 240 females from weaning to 5 months of age in single- or mixed- strain trios, in cages allocated to enriched or standard treatments. Mice were screened for a range of 26 commonly-measured behavioural, physiological and haematological variables. Results Living in mixed-strain trios did not compromise mouse welfare (assessed via corticosterone metabolite output, stereotypic behaviour, signs of aggression, and other variables. It also did not alter the direction or magnitude of any strain- or enrichment-typical difference across the 26 measured variables, or increase variance in the data: indeed variance was significantly decreased by mixed- strain housing. Furthermore, using Monte Carlo simulations to quantify the statistical power benefits of this approach over a conventional design demonstrated that for our effect sizes, the split- plot design would require significantly fewer mice (under half in most cases to achieve a power of 80 %. Conclusions Mixed-strain housing allows several strains to be tested at once, and potentially refines traditional marking practices

  17. The Efficiency of Split Panel Designs in an Analysis of Variance Model

    Science.gov (United States)

    Wang, Wei-Guo; Liu, Hai-Jun

    2016-01-01

    We consider split panel design efficiency in analysis of variance models, that is, the determination of the cross-sections series optimal proportion in all samples, to minimize parametric best linear unbiased estimators of linear combination variances. An orthogonal matrix is constructed to obtain manageable expression of variances. On this basis, we derive a theorem for analyzing split panel design efficiency irrespective of interest and budget parameters. Additionally, relative estimator efficiency based on the split panel to an estimator based on a pure panel or a pure cross-section is present. The analysis shows that the gains from split panel can be quite substantial. We further consider the efficiency of split panel design, given a budget, and transform it to a constrained nonlinear integer programming. Specifically, an efficient algorithm is designed to solve the constrained nonlinear integer programming. Moreover, we combine one at time designs and factorial designs to illustrate the algorithm’s efficiency with an empirical example concerning monthly consumer expenditure on food in 1985, in the Netherlands, and the efficient ranges of the algorithm parameters are given to ensure a good solution. PMID:27163447

  18. Relative Efficiency of Split-plot Design (SPD) to Randomized ...

    African Journals Online (AJOL)

    PROF. O. E. OSUAGWU

    2013-06-01

    Jun 1, 2013 ... West African Journal of Industrial and Academic Research Vol.7 No. 1 June .... effects. They concluded that the proposed efficiency measures provide feasible solutions for .... Fm = d.f for the whole-plot treatment; Fb= d.f for the ...

  19. Split double factorial with additional treatment and the post-harvest of Niagara grapes

    Directory of Open Access Journals (Sweden)

    Pórtya Piscitelli Cavalcanti

    2015-09-01

    Full Text Available ABSTRACTThis study aims to discuss and explain how to deal with the analysis of experiments conducted in completely randomized design (CRD and subdivided into double factorial with additional treatment in the plot. In addition it was illustrate the discussion by analyzing data from an experiment on post-harvest of Niagara grapes. The sums of squares for each source of variation are presented, while discussing how the additional treatment affects the whole variation. Niagara grapes were treated in the pre-harvest with three preservatives (calcium chloride, calcium nitrate and calcium lactate at 0%, 0.5%, 1% and 2% and stored for 0, 10, 20 and 30 days.All the preservatives evaluated at 0% represented the control (additional treatment.

  20. Design of a factorial experiment with randomization restrictions to assess medical device performance on vascular tissue.

    Science.gov (United States)

    Diestelkamp, Wiebke S; Krane, Carissa M; Pinnell, Margaret F

    2011-05-20

    Energy-based surgical scalpels are designed to efficiently transect and seal blood vessels using thermal energy to promote protein denaturation and coagulation. Assessment and design improvement of ultrasonic scalpel performance relies on both in vivo and ex vivo testing. The objective of this work was to design and implement a robust, experimental test matrix with randomization restrictions and predictive statistical power, which allowed for identification of those experimental variables that may affect the quality of the seal obtained ex vivo. The design of the experiment included three factors: temperature (two levels); the type of solution used to perfuse the artery during transection (three types); and artery type (two types) resulting in a total of twelve possible treatment combinations. Burst pressures of porcine carotid and renal arteries sealed ex vivo were assigned as the response variable. The experimental test matrix was designed and carried out as a split-plot experiment in order to assess the contributions of several variables and their interactions while accounting for randomization restrictions present in the experimental setup. The statistical software package SAS was utilized and PROC MIXED was used to account for the randomization restrictions in the split-plot design. The combination of temperature, solution, and vessel type had a statistically significant impact on seal quality. The design and implementation of a split-plot experimental test-matrix provided a mechanism for addressing the existing technical randomization restrictions of ex vivo ultrasonic scalpel performance testing, while preserving the ability to examine the potential effects of independent factors or variables. This method for generating the experimental design and the statistical analyses of the resulting data are adaptable to a wide variety of experimental problems involving large-scale tissue-based studies of medical or experimental device efficacy and performance.

  1. On the Kendrick Mass Defect Plots of Multiply Charged Polymer Ions: Splits, Misalignments, and How to Correct Them

    Science.gov (United States)

    Fouquet, Thierry N. J.; Cody, Robert B.; Ozeki, Yuka; Kitagawa, Shinya; Ohtani, Hajime; Sato, Hiroaki

    2018-05-01

    The Kendrick mass defect (KMD) analysis of multiply charged polymeric distributions has recently revealed a surprising isotopic split in their KMD plots—namely a 1/z difference between KMDs of isotopes of an oligomer at charge state z. Relying on the KMD analysis of actual and simulated distributions of poly(ethylene oxide) (PEO), the isotopic split is mathematically accounted for and found to go with an isotopic misalignment in certain cases. It is demonstrated that the divisibility (resp. indivisibility) of the nominal mass of the repeating unit (R) by z is the condition for homolog ions to line up horizontally (resp. misaligned obliquely) in a KMD plot. Computing KMDs using a fractional base unit R/z eventually corrects the misalignments for the associated charge state while using the least common multiple of all the charge states as the divisor realigns all the points at once. The isotopic split itself can be removed by using either a new charge-dependent KMD plot compatible with any fractional base unit or the remainders of KM (RKM) recently developed for low-resolution data all found to be linked in a unified theory. These original applications of the fractional base units and the RKM plots are of importance theoretically to satisfy the basics of a mass defect analysis and practically for a correct data handling of single stage and tandem mass spectra of multiply charged homo- and copolymers.

  2. Implementing Clinical Research Using Factorial Designs: A Primer.

    Science.gov (United States)

    Baker, Timothy B; Smith, Stevens S; Bolt, Daniel M; Loh, Wei-Yin; Mermelstein, Robin; Fiore, Michael C; Piper, Megan E; Collins, Linda M

    2017-07-01

    Factorial experiments have rarely been used in the development or evaluation of clinical interventions. However, factorial designs offer advantages over randomized controlled trial designs, the latter being much more frequently used in such research. Factorial designs are highly efficient (permitting evaluation of multiple intervention components with good statistical power) and present the opportunity to detect interactions amongst intervention components. Such advantages have led methodologists to advocate for the greater use of factorial designs in research on clinical interventions (Collins, Dziak, & Li, 2009). However, researchers considering the use of such designs in clinical research face a series of choices that have consequential implications for the interpretability and value of the experimental results. These choices include: whether to use a factorial design, selection of the number and type of factors to include, how to address the compatibility of the different factors included, whether and how to avoid confounds between the type and number of interventions a participant receives, and how to interpret interactions. The use of factorial designs in clinical intervention research poses choices that differ from those typically considered in randomized clinical trial designs. However, the great information yield of the former encourages clinical researchers' increased and careful execution of such designs. Copyright © 2017. Published by Elsevier Ltd.

  3. Information Management for Factory Planning and Design

    OpenAIRE

    Chen, Danfang

    2012-01-01

    This thesis is dedicated to the manufacturing industry for the improvement of information management within the factory planningand design domain, and for more efficient factory planning and design. Currently the manufacturing industry lacks sufficient methods for capturing, structuring, and representing information and knowledge for easy access, exchange, integration and reuse within the domain. Therefore the focus of this thesis is on information and knowledge management within factory plan...

  4. General B factory design considerations

    International Nuclear Information System (INIS)

    Zisman, M.S.

    1992-12-01

    We describe the general considerations that go into the design of an asymmetric B factory collider. Justification is given for the typical parameters of such a facility, and the physics and technology challenges that arise from these parameter choices are discussed. Cost and schedule issues for a B factory are discussed briefly. A summary of existing proposals is presented, noting their similarities and differences

  5. Mainz/PSI φ-factory design considerations

    International Nuclear Information System (INIS)

    Streun, A.

    1991-01-01

    Design considerations for a φ-factory with a Luminosity of the order of 10 33 cm -2 s -1 lead to the concept of a multi-bunch round beam double storage ring with superconducting solenoids for micro-beta focusing and beam rotation. Simulations of the beam-beam-interaction indicate, that significantly higher beam-beam-parameters may become possible with round beams. A rough draft design of a round beam φ-factory is presented. (orig.)

  6. Evaluating Plot Designs for the Tropics

    Science.gov (United States)

    Paul C. van Deusen; Bruce Bayle

    1991-01-01

    Theory and procedures are reviewed for determining the best type of plot for a given forest inventory. A general methodology is given that clarifies the relationship between different plot designs and the associated methods to produce the inventory estimates.

  7. Urban pattern: Layout design by hierarchical domain splitting

    KAUST Repository

    Yang, Yongliang; Wang, Jun; Vouga, Etienne; Wonka, Peter

    2013-01-01

    We present a framework for generating street networks and parcel layouts. Our goal is the generation of high-quality layouts that can be used for urban planning and virtual environments. We propose a solution based on hierarchical domain splitting using two splitting types: streamline-based splitting, which splits a region along one or multiple streamlines of a cross field, and template-based splitting, which warps pre-designed templates to a region and uses the interior geometry of the template as the splitting lines. We combine these two splitting approaches into a hierarchical framework, providing automatic and interactive tools to explore the design space.

  8. Urban pattern: Layout design by hierarchical domain splitting

    KAUST Repository

    Yang, Yongliang

    2013-11-06

    We present a framework for generating street networks and parcel layouts. Our goal is the generation of high-quality layouts that can be used for urban planning and virtual environments. We propose a solution based on hierarchical domain splitting using two splitting types: streamline-based splitting, which splits a region along one or multiple streamlines of a cross field, and template-based splitting, which warps pre-designed templates to a region and uses the interior geometry of the template as the splitting lines. We combine these two splitting approaches into a hierarchical framework, providing automatic and interactive tools to explore the design space.

  9. Effects of process parameters on ozone washing for denim using 3/sup 3/ factorial design

    International Nuclear Information System (INIS)

    Asim, F.; Mahmood, M.

    2017-01-01

    Denim garment is getting popular day by day. It is highly demandable because of its versatility, comfort and durability. Different techniques of denim washing increase this demand drastically. Denim washing is the process to enhance the appearance of a garment. This enhanced appearance may be the aged look, faded look, greyer cast, or any other shade setting or resin application. The two most advanced washing techniques are; ozone wash and laser wash. The effects of ozone on environment as well as on the garment are significant and cannot be neglected because number of benefits achieved such as time saving, less energy consumption, chemical, labour cost reduction, less discharge of water and chemicals. Therefore, effects of process parameters on ozone washing for denim fabric have been investigated in this research work using three level factorial design. 33 factorial design has been designed and conducted to investigate the effect of gas concentration, time and speed on the response variables namely; Shrinkage, Tensile and Tear strength of ozone washing. The influence of individual factors and their interactions has been critically examined using software Design Expert 8.0. Prior to the analysis of variance model accuracy has been examined through various residuals plots. The study of residuals plots shown that the residuals are normally distributed and significant evidence of possible outliers was not found. So the model can be used to predicted results with 95% confidence interval. The results from the experiment suggest that two out of three factors were significant, which are speed and time that influences mainly on the tear strength of the denim garment. (author)

  10. Update formulas for split-plot and block designs

    NARCIS (Netherlands)

    H. Arnouts (Heidi); P.P. Goos (Peter)

    2009-01-01

    textabstractFor the algorithmic construction of optimal experimental designs, it is important to be able to evaluate small modifications of given designs in terms of the optimality criteria at a low computational cost. This can be achieved by using powerful update formulas for the optimality

  11. Design, analysis and presentation of factorial randomised controlled trials

    Directory of Open Access Journals (Sweden)

    Little Paul

    2003-11-01

    Full Text Available Abstract Background The evaluation of more than one intervention in the same randomised controlled trial can be achieved using a parallel group design. However this requires increased sample size and can be inefficient, especially if there is also interest in considering combinations of the interventions. An alternative may be a factorial trial, where for two interventions participants are allocated to receive neither intervention, one or the other, or both. Factorial trials require special considerations, however, particularly at the design and analysis stages. Discussion Using a 2 × 2 factorial trial as an example, we present a number of issues that should be considered when planning a factorial trial. The main design issue is that of sample size. Factorial trials are most often powered to detect the main effects of interventions, since adequate power to detect plausible interactions requires greatly increased sample sizes. The main analytical issues relate to the investigation of main effects and the interaction between the interventions in appropriate regression models. Presentation of results should reflect the analytical strategy with an emphasis on the principal research questions. We also give an example of how baseline and follow-up data should be presented. Lastly, we discuss the implications of the design, analytical and presentational issues covered. Summary Difficulties in interpreting the results of factorial trials if an influential interaction is observed is the cost of the potential for efficient, simultaneous consideration of two or more interventions. Factorial trials can in principle be designed to have adequate power to detect realistic interactions, and in any case they are the only design that allows such effects to be investigated.

  12. A conceptual design of circular Higgs factory

    Energy Technology Data Exchange (ETDEWEB)

    Cai, Yunhai

    2016-11-30

    Similar to a super B-factory, a circular Higgs factory (CHF) will require strong focusing systems near the interaction points and a low-emittance lattice in the arcs to achieve a factory luminosity. At electron beam energy of 125 GeV, beamstrahlung effects during the collision pose an additional challenge to the collider design. In particular, a large momentum acceptance at the 2% level is necessary to retain an adequate beam lifetime. This turns out to be the most challenging aspect in the design of a CHF. In this paper, an example will be provided to illustrate the beam dynamics in a CHF, emphasizing the chromatic optics. Basic optical modules and advanced analysis will be presented. Most importantly, we will show that 2% momentum aperture is achievable.

  13. Handbook factory planning and design

    CERN Document Server

    Wiendahl, Hans-Peter; Nyhuis, Peter

    2015-01-01

    This handbook introduces a methodical approach and pragmatic concept for the planning and design of changeable factories that act in strategic alliances to supply the ever-changing needs of the global market. In the first part, the change drivers of manufacturing enterprises and the resulting new challenges are considered in detail with focus on an appropriate change potential. The second part concerns the design of the production facilities and systems on the factory levels work place, section, building and site under functional, organisational, architectural and strategic aspects keeping in mind the environmental, health and safety aspects including corporate social responsibility. The third part is dedicated to the planning and design method that is based on a synergetic interaction of process and space. The accompanying project management of the planning and construction phase and the facility management for the effective utilization of the built premises close the book. -        Concise overview o...

  14. CONFOUNDING STRUCTURE OF TWO-LEVEL NONREGULAR FACTORIAL DESIGNS

    Institute of Scientific and Technical Information of China (English)

    Ren Junbai

    2012-01-01

    In design theory,the alias structure of regular fractional factorial designs is elegantly described with group theory.However,this approach cannot be applied to nonregular designs directly. For an arbitrary nonregular design,a natural question is how to describe the confounding relations between its effects,is there any inner structure similar to regular designs? The aim of this article is to answer this basic question.Using coefficients of indicator function,confounding structure of nonregular fractional factorial designs is obtained as linear constrains on the values of effects.A method to estimate the sparse significant effects in an arbitrary nonregular design is given through an example.

  15. FFAG Designs for the International Design Study for the Neutrino Factory

    Energy Technology Data Exchange (ETDEWEB)

    Berg, J.S.; Machida, S.

    2009-05-04

    The International Design Study for the Neutrino Factory (IDS-NF) aims to produce a design report for a neutrino factory. One component of that design is a linear nonscaling fixed-field alternating gradient accelerator (FFAG) that will accelerate to the final energy of 25 GeV. An FFAG is used to reduce the machine cost by maximizing the number of passes made through the RF cavities. We present some design options for this FFAG, individually optimized for cost. We study the addition of nonlinear magnets to the lattice to improve the performance of the lattice and consider the negative effects of doing so.

  16. Flow-based approach for holistic factory engineering and design

    OpenAIRE

    Constantinescu, C.; Westkämper, E.

    2010-01-01

    The engineering of future factories requires digital tools along life cycle phases from investment planning to ramp-up. Manufacturers need scientific-based integrated highly dynamic data management systems for the participative and integrated factory planning. The paper presents a new approach for the continuously integrated product design, factory and process planning, through a service-oriented architecture for the implementation of digital factory tools. A first prototype of the digital fa...

  17. B factory RF system design issues

    International Nuclear Information System (INIS)

    Zisman, M.S.

    1992-01-01

    We discuss the issues of relevance to the design of a B factory RF system. First, the general parameter regime is outlined, and the reasons behind certain commonly made choices are indicated. This regime involves high beam currents, and many relatively short bunches. Next, the physics difficulties associated with coupled-bunch instabilities are described briefly. We then describe in general terms the alternative approaches taken by various B factory designers, the motivation for these choices, and the technical issues raised by them. Technical solutions have been proposed for both the room-temperature and the superconducting RF scenarios, and considerable R ampersand D is being carried out worldwide to confirm and optimize these solutions

  18. B factory rf system design issues

    International Nuclear Information System (INIS)

    Zisman, M.S.

    1992-06-01

    We discuss the issues of relevance to the design of a B factory RF system. First, the general parameter regime is outlined, and the reasons behind certain commonly made choices are indicated. This regime involves high beam currents, and many relatively short bunches. Next, the physics difficulties associated with coupled-bunch instabilities are described briefly. We then describe in general terms the alternative approaches taken by various B factory designers, the motivation for these choices, and the technical issues raised by them. Technical solutions have been proposed for both the room-temperature and the superconducting RF scenarios, and considerable R ampersand D is being carried out worldwide to confirm and optimize these solutions

  19. Argonne Tau-charm factory collider design study

    International Nuclear Information System (INIS)

    Teng, L.C.; Crosbie, E.A.; Norem, J.

    1995-01-01

    The design approach and design principles for a Tau-charm Factory at Argonne were studied. These studies led to a set of preliminary parameters and tentative component features as presented in this paper

  20. The Mathematics of Symmetrical Factorial Designs

    Indian Academy of Sciences (India)

    The Mathematics of Symmetrical Factorial Designs. Mausumi Bose (nee Sen) obtained her MSc degree in. Statistics from the Calcutta. University and PhD degree from the Indian Statistical. Institute. She is on the faculty of the Indian. Statistical Institute. Her main field of research interest is design and analysis of experiments.

  1. Apiary B Factory lattice design

    International Nuclear Information System (INIS)

    Donald, M.H.R.; Garren, A.A.

    1991-04-01

    The Apiary B Factory is a proposed high-intensity electron-positron collider. This paper will present the lattice design for this facility, which envisions two rings with unequal energies in the PEP tunnel. The design has many interesting optical and geometrical features due to the needs to conform to the existing tunnel, and to achieve the necessary emittances, damping times and vacuum. Existing hardware is used to a maximum extent. 8 figs. 1 tab

  2. Formulation of topical bioadhesive gel of aceclofenac using 3-level factorial design.

    Science.gov (United States)

    Singh, Sanjay; Parhi, Rabinarayan; Garg, Anuj

    2011-01-01

    The objective of this work was to develop bioadhesive topical gel of Aceclofenac with the help of response-surface approach. Experiments were performed according to a 3-level factorial design to evaluate the effects of two independent variables [amount of Poloxamer 407 (PL-407 = X1) and hydroxypropylmethyl cellulose K100 M (HPMC = X2)] on the bioadhesive character of gel, rheological property of gel (consistency index), and in-vitro drug release. The best model was selected to fit the data. Mathematical equation was generated by Design Expert® software for the model which assists in determining the effect of independent variables. Response surface plots were also generated by the software for analyzing effect of the independent variables on the response. Quadratic model was found to be the best for all the responses. Both independent variable (X1 and X2) were found to have synergistic effect on bioadhesion (Y1) but the effect of HPMC was more pronounced than PL-407. Consistency index was enhanced by increasing the level of both independent variables. An antagonistic effect of both independent variables was found on cumulative percentage release of drug in 2 (Y3) and 8 h (Y4). Both independent variables approximately equally contributed the antagonistic effect on Y3 whereas antagonistic effect of HPMC was more pronounced than PL-407. The effect of formulation variables on the product characteristics can be easily predicted and precisely interpreted by using a 3-level factorial experimental design and generated quadratic mathematical equations.

  3. Argonne Tau-charm Factory collider design study

    International Nuclear Information System (INIS)

    Teng, L.C.; Crosbie, E.A.; Norem, J.; Repond, J.

    1996-01-01

    The design approach and design principles for a Tau-charm Factory at Argonne were studied. These studies led to a set of preliminary parameters and tentative component features as presented in this paper. copyright 1996 American Institute of Physics

  4. D.3.3 PLOT Persuasive Learning Design Framework

    DEFF Research Database (Denmark)

    Gram-Hansen, Sandra Burri

    2012-01-01

    In this third and final deliverable of WP3: Persuasive Learning Designs, the theoretical cross field between persuasion and learning and the practical analysis of the technological learning tools and products which are currently related to the PLOT project, namely the GLOMaker and the 3ET tool......, are linked together as persuasive learning designs are defined and exemplified through the four e-PLOT cases. Based on the literary study of D.3.1 as well as the subsequent discussions and reflections regarding the theoretical foundation and practical application of persuasive learning technologies......-PLOT work cases. In conclusion, the report presents a number of suggestions regarding the improvement of the two learning tools, which from a theoretical perspective will enhance the persuasive potential, and which can be taken into consideration in WP4 and 5....

  5. Design and manufacture NCS instruments for cement factories

    International Nuclear Information System (INIS)

    Nguyen Thanh Tuy; Nguyen Tien Dung; Dang Nguyet Anh; Nguyen Phuc; Khuong Thanh Tuan; Luong Duc Long; Pham Trong Quyen

    2003-01-01

    The ministry project 'Design and manufacture some of NCS instruments for cement factories' is a part of instrumentation for cement production in Vietnam. The objectives of the project include: 1/Design and manufacture the automatic control system for cement raw material mixing, connected to components X-ray analyzer through serial port of PC; 2/Design and manufacture the automatic discharge control system using gamma rays. The instruments, made by the project , for controlling the conveyor belt weighing machine can be easily improved for various types of conveyor belt weighing machines. Their mobility and software equipped can be adapted for requirement of modern cement production technology. The instruments are operating well in some cement factories and they are helping in quality control. (NHA)

  6. Gravel admix, vegetation, and soil water interactions in protective barriers: Experimental design, construction, and initial conditions

    International Nuclear Information System (INIS)

    Waugh, W.J.

    1989-05-01

    The purpose of this study is to measure the interactive effects of gravel admix and greater precipitation on soil water storage and plant abundance. The study is one of many tasks in the Protective Barrier Development Program for the disposal of Hanford defense waste. A factorial field-plot experiment was set up at the site selected as the borrow area for barrier topsoil. Gravel admix, vegetation, and enhanced precipitation treatments were randomly assigned to the plots using a split-split plot design structure. Changes in soil water storage and plant cover were monitored using neutron probe and point intercept methods, respectively. The first-year results suggest that water extraction by plants will offset gravel-caused increases in soil water storage. Near-surface soil water contents were much lower in graveled plots with plants than in nongraveled plots without plants. Large inherent variability in deep soil water storage masked any effects gravel may have had on water content below the root zone. In the future, this source of variation will be removed by differencing monthly data series and testing for changes in soil water storage. Tests of the effects of greater precipitation on soil water storage were inconclusive. A telling test will be possible in the spring of 1988, following the first wet season during which normal precipitation is doubled. 26 refs., 9 figs., 9 tabs

  7. Worm plot to diagnose fit in quantile regression

    NARCIS (Netherlands)

    Buuren, S. van

    2007-01-01

    The worm plot is a series of detrended Q-Q plots, split by covariate levels. The worm plot is a diagnostic tool for visualizing how well a statistical model fits the data, for finding locations at which the fit can be improved, and for comparing the fit of different models. This paper shows how the

  8. Worm plot to diagnose fit in quantile regression

    NARCIS (Netherlands)

    Buuren, S. van

    2007-01-01

    The worm plot is a series of detrended Q-Q plots, split by covariate levels. The worm plot is a diagnostic tool for visualizing how well a statistical model fits the data, for finding locations at which the fit can be improved, and for comparing the fit of different models. This paper shows how

  9. Effects of drought stress and different densities on oil yield and ...

    African Journals Online (AJOL)

    For evaluation of water deficit stress and planting density effects on the oil and biological yield attributes of sunflower, an experiment was conducted in a randomized complete block design (RCBD) based split plot factorial design in three replications in the research field of Baku State University, Baku, Azerbaijan, in 2009.

  10. Architectural design of experience based factory model for software ...

    African Journals Online (AJOL)

    architectural design. Automation features are incorporated in the design in which workflow system and intelligent agents are integrated, and the facilitation of cloud environment is empowered to further support the automation. Keywords: architectural design; knowledge management; experience factory; workflow;

  11. Beyond the Interconnections: Split Manufacturing in RF Designs

    Directory of Open Access Journals (Sweden)

    Yu Bi

    2015-08-01

    Full Text Available With the globalization of the integrated circuit (IC design flow of chip fabrication, intellectual property (IP piracy is becoming the main security threat. While most of the protection methods are dedicated for digital circuits, we are trying to protect radio-frequency (RF designs. For the first time, we applied the split manufacturing method in RF circuit protection. Three different implementation cases are introduced for security and design overhead tradeoffs, i.e., the removal of the top metal layer, the removal of the top two metal layers and the design obfuscation dedicated to RF circuits. We also developed a quantitative security evaluation method to measure the protection level of RF designs under split manufacturing. Finally, a simple Class AB power amplifier and a more sophisticated Class E power amplifier are used for the demonstration through which we prove that: (1 the removal of top metal layer or the top two metal layers can provide high-level protection for RF circuits with a lower request to domestic foundries; (2 the design obfuscation method provides the highest level of circuit protection, though at the cost of design overhead; and (3 split manufacturing may be more suitable for RF designs than for digital circuits, and it can effectively reduce IP piracy in untrusted off-shore foundries.

  12. Design studies for the Positron Factory

    International Nuclear Information System (INIS)

    Okada, S.; Sunaga, H.; Kaneko, H.; Masuno, S.; Kawasuso, A.; Sakai, T.; Takizawa, H.; Yotsumoto, K.; Honda, Y.; Tagawa, S.

    1996-01-01

    In the design study for the Positron Factory, a feasibility of simultaneous extraction of multi-channel monoenergetic positron beams, which had been proposed at the previous conference (Linac 94), was demonstrated by an experiment using an electron linac. On the basis of the experimental result, an efficient moderator structure, which is composed of honeycomb-like assembled moderator foils and reflectors, is proposed. (author)

  13. Diseños experimentales e investigacion científica

    Directory of Open Access Journals (Sweden)

    Badii, M.H

    2007-07-01

    Full Text Available The basics of the experimental designs are noted. Different features of common types of experimental designs such as the completely randomized design, the randomized block design, the Latin Square design, the split plot design and the factorial design are described. Each experimental design is illustrated by an example using real data. The application of experimental designs to the scientific research is discussed.

  14. Dual-Band Split-Ring Antenna Design for WLAN Applications

    OpenAIRE

    BAŞARAN, S. Cumhur; ERDEMLİ, Yunus E.

    2014-01-01

    A dual-band microstrip antenna based on split-ring elements is introduced for WLAN (2.4/5.2 GHz) applications. The proposed split-ring antenna (SRA) has a compact novel design which provides about 2% impedance-bandwidth without a need for additional matching network. Analysis and design of the proposed microstrip antenna is carried out by means of full-wave simulators based on the finite-element method.

  15. MapFactory - Towards a mapping design pattern for big geospatial data

    Science.gov (United States)

    Rautenbach, Victoria; Coetzee, Serena

    2018-05-01

    With big geospatial data emerging, cartographers and geographic information scientists have to find new ways of dealing with the volume, variety, velocity, and veracity (4Vs) of the data. This requires the development of tools that allow processing, filtering, analysing, and visualising of big data through multidisciplinary collaboration. In this paper, we present the MapFactory design pattern that will be used for the creation of different maps according to the (input) design specification for big geospatial data. The design specification is based on elements from ISO19115-1:2014 Geographic information - Metadata - Part 1: Fundamentals that would guide the design and development of the map or set of maps to be produced. The results of the exploratory research suggest that the MapFactory design pattern will help with software reuse and communication. The MapFactory design pattern will aid software developers to build the tools that are required to automate map making with big geospatial data. The resulting maps would assist cartographers and others to make sense of big geospatial data.

  16. Bioretention Systems: Partial Factorial Designs for Nitrate Removal

    Science.gov (United States)

    Changes in nutrient loadings are monitored by introducing captured stormwater runoff into eight outdoor rain gardens at EPA’s Urban Water Research Facility in Edison, New Jersey scaled for residential and urban landscapes. The partial factorial design includes non-vegetated meso...

  17. Fitting diameter distribution models to data from forest inventories with concentric plot design

    Energy Technology Data Exchange (ETDEWEB)

    Nanos, N.; Sjöstedt de Luna, S.

    2017-11-01

    Aim: Several national forest inventories use a complex plot design based on multiple concentric subplots where smaller diameter trees are inventoried when lying in the smaller-radius subplots and ignored otherwise. Data from these plots are truncated with threshold (truncation) diameters varying according to the distance from the plot centre. In this paper we designed a maximum likelihood method to fit the Weibull diameter distribution to data from concentric plots. Material and methods: Our method (M1) was based on multiple truncated probability density functions to build the likelihood. In addition, we used an alternative method (M2) presented recently. We used methods M1 and M2 as well as two other reference methods to estimate the Weibull parameters in 40000 simulated plots. The spatial tree pattern of the simulated plots was generated using four models of spatial point patterns. Two error indices were used to assess the relative performance of M1 and M2 in estimating relevant stand-level variables. In addition, we estimated the Quadratic Mean plot Diameter (QMD) using Expansion Factors (EFs). Main results: Methods M1 and M2 produced comparable estimation errors in random and cluster tree spatial patterns. Method M2 produced biased parameter estimates in plots with inhomogeneous Poisson patterns. Estimation of QMD using EFs produced biased results in plots within inhomogeneous intensity Poisson patterns. Research highlights:We designed a new method to fit the Weibull distribution to forest inventory data from concentric plots that achieves high accuracy and precision in parameter estimates regardless of the within-plot spatial tree pattern.

  18. Design Learning of Teaching Factory in Mechanical Engineering

    Science.gov (United States)

    Putra, R. C.; Kusumah, I. H.; Komaro, M.; Rahayu, Y.; Asfiyanur, E. P.

    2018-02-01

    The industrial world that is the target of the process and learning outcomes of vocational high school (SMK) has its own character and nuance. Therefore, vocational education institutions in the learning process should be able to make the appropriate learning approach and in accordance with the industrial world. One approach to learning that is based on production and learning in the world of work is by industry-based learning or known as Teaching Factory, where in this model apply learning that involves direct students in goods or service activities are expected to have the quality so it is worth selling and accepted by consumers. The method used is descriptive approach. The purpose of this research is to get the design of the teaching factory based on the competency requirements of the graduates of the spouse industry, especially in the engineering department. The results of this study is expected to be one of the choice of model factory teaching in the field of machinery engineering in accordance with the products and competencies of the graduates that the industry needs.

  19. Design and analysis of unequal split Bagley power dividers

    Science.gov (United States)

    Abu-Alnadi, Omar; Dib, Nihad; Al-Shamaileh, Khair; Sheta, Abdelfattah

    2015-03-01

    In this article, we propose a general design procedure to develop unequal split Bagley power dividers (BPDs). Based on the mathematical approach carried out in the insight of simple circuit and transmission line theories, exact design equations for 3-way and 5-way BPDs are derived. Utilising the developed equations leads to power dividers with the ability of offering different output power ratios through a suitable choice of the characteristic impedances of the interconnecting transmission lines. For verification purposes, a 1:2:1 3-way, 1:2:1:2:1 5-way and 1:3:1:3:1 5-way BPDs are designed and fabricated. The experimental and full-wave simulation results prove the validity of the designed unequal split BPDs.

  20. Effects of D-a-tocopherol and dietary energy on growth and health of preruminant dairy calves

    Science.gov (United States)

    To observe the effects of supplemental dietary d-a-tocopherol in relation to dietary energy on growth and immune status in dairy calves, 32 newborn Holstein bull calves were assigned to 1 of 4 treatments for 5 weeks in a 2x2 factorial randomized complete block, split-plot design. Calves received mod...

  1. D.3.2 PLOT Persuasive Learning Design Framework

    DEFF Research Database (Denmark)

    Gram-Hansen, Sandra Burri; Schärfe, Henrik; Winther-Nielsen, Nicolai

    2011-01-01

    of the technological learning tools and products which are currently related to the PLOT project, namely the GLOMaker and the 3ET tool, and a selection of GLOs and learning exercises. The primary focus of the analysis is to explore how the theoretical perspectives presented in D.3.1 are represented in these tools...... as an: ‚Internal report for project use containing an empirically-based assessment of existing systems and their potential in terms of learning and persuasion. This will be used as a discussion document by the consortium.‛ To meet the requirements of this deliverable, this documents presents analysis......, in particular the notions of persuasive design and constructive alignment. Whilst the report provides a persuasive design perspective on the technologies related to Euro PLOT, it must be stressed that if the document is to function as a basis for further discussion within the consortium, the partners...

  2. A Preliminary Interaction Region Design for a Super B-Factory

    CERN Document Server

    Sullivan, Michael K; Donald, Martin; Ecklund, Stanley; Novokhatski, Alexander; Seeman, John; Wienands, Ulrich

    2005-01-01

    The success of the two B-Factories (PEP-II and KEKB) has encouraged us to look at design parameters for a B-Factory with a 30-50 times increase in the luminosity of the present machines (L~1e36). In order to achieve this high luminosity, the beta y* values are reduced to 3-2 mm, the bunch spacing is minimized (0.6-0.3 m) and the bunch currents are increased. Total beam currents range from 5-25 A. The interaction region (IR) of these "SuperB" designs presents special challenges. Synchrotron radiation fans from local bending in shared magnets and from upstream sources pose difficulties due to the high power levels in these fans. High-order-mode(HOM)heating, effects that have been seen in the present B-factories, will become much more pronounced with the very short bunches and high beam currents. Masking the detector beam pipe from synchrotron radiation must take into account effects of HOM power generation. Backgrounds that are a function of the luminosity will become very important. We presen...

  3. Full factorial design analysis of carbon nanotube polymer-cement composites

    Directory of Open Access Journals (Sweden)

    Fábio de Paiva Cota

    2012-08-01

    Full Text Available The work described in this paper is related to the effect of adding carbon nanotubes (CNT on the mechanical properties of polymer-cement composites. A full factorial design has been performed on 160 samples to identify the contribution provided by the following factors: polymeric phase addition, CNT weight addition and water/cement ratio. The response parameters of the full factorial design were the bulk density, apparent porosity, compressive strength and elastic modulus of the polymer-cement-based nanocomposites. All the factors considered in this analysis affected significantly the bulk density and apparent porosity of the composites. The compressive strength and elastic modulus were affected primarily by the cross-interactions between polymeric phase and CNT additions, and the water/cement ratio with polymeric phase factors.

  4. Numerical investigation of a dual-loop EGR split strategy using a split index and multi-objective Pareto optimization

    International Nuclear Information System (INIS)

    Park, Jungsoo; Song, Soonho; Lee, Kyo Seung

    2015-01-01

    Highlights: • Model-based control of dual-loop EGR system is performed. • EGR split index is developed to provide non-dimensional index for optimization. • EGR rates are calibrated using EGR split index at specific operating conditions. • Multi-objective Pareto optimization is performed to minimize NO X and BSFC. • Optimum split strategies are suggested with LP-rich dual-loop EGR at high load. - Abstract: A proposed dual-loop exhaust-gas recirculation (EGR) system that combines the features of high-pressure (HP) and low-pressure (LP) systems is considered a key technology for improving the combustion behavior of diesel engines. The fraction of HP and LP flows, known as the EGR split, for a given dual-loop EGR rate play an important role in determining the engine performance and emission characteristics. Therefore, identifying the proper EGR split is important for the engine optimization and calibration processes, which affect the EGR response and deNO X efficiencies. The objective of this research was to develop a dual-loop EGR split strategy using numerical analysis and one-dimensional (1D) cycle simulation. A control system was modeled by coupling the 1D cycle simulation and the control logic. An EGR split index was developed to investigate the HP/LP split effects on the engine performance and emissions. Using the model-based control system, a multi-objective Pareto (MOP) analysis was used to minimize the NO X formation and fuel consumption through optimized engine operating parameters. The MOP analysis was performed using a response surface model extracted from Latin hypercube sampling as a fractional factorial design of experiment. By using an LP rich dual-loop EGR, a high EGR rate was attained at low, medium, and high engine speeds, increasing the applicable load ranges compared to base conditions

  5. Winter cover crops on processing tomato yield, quality, pest pressure, nitrogen availability, and profit margins

    OpenAIRE

    Belfry, Kimberly D.; Trueman, Cheryl; Vyn, Richard J.; Loewen, Steven A.; Van Eerd, Laura L.

    2017-01-01

    Much of cover crop research to date focuses on key indicators of impact without considering the implications over multiple years, in the absence of a systems-based approach. To evaluate the effect of three years of autumn cover crops on subsequent processing tomato (Solanum lycopersicum L.) production in 2010 and 2011, a field split-split-plot factorial design trial with effects of cover crop type, urea ammonium nitrate fertilizer rate (0 or 140 kg N ha-1 preplant broadcast incorporated) and ...

  6. Design optimization of condenser microphone: a design of experiment perspective.

    Science.gov (United States)

    Tan, Chee Wee; Miao, Jianmin

    2009-06-01

    A well-designed condenser microphone backplate is very important in the attainment of good frequency response characteristics--high sensitivity and wide bandwidth with flat response--and low mechanical-thermal noise. To study the design optimization of the backplate, a 2(6) factorial design with a single replicate, which consists of six backplate parameters and four responses, has been undertaken on a comprehensive condenser microphone model developed by Zuckerwar. Through the elimination of insignificant parameters via normal probability plots of the effect estimates, the projection of an unreplicated factorial design into a replicated one can be performed to carry out an analysis of variance on the factorial design. The air gap and slot have significant effects on the sensitivity, mechanical-thermal noise, and bandwidth while the slot/hole location interaction has major influence over the latter two responses. An organized and systematic approach of designing the backplate is summarized.

  7. Gaming in the Classroom: An Innovative Way to Teach Factorial Designs

    Science.gov (United States)

    Stansbury, Jessica A.; Munro, Geoffrey D.

    2013-01-01

    This study tested the effectiveness of video game use for instruction of factorial designs in a research methods course. Students designed and conducted a mini study, playing "Dance, Dance, Revolution", using video game scores as the dependent variable. A mixed-design analysis of variance revealed a significantly greater increase from pretest to…

  8. Factorial study of rain garden design for nitrogen removal

    Science.gov (United States)

    Abstract Nitrate (〖NO〗_3^--N ) removal studies in bioretention systems showed great variability in removal rates and in some cases 〖NO〗_3^--N was exported. A 3-way factorial design (2 x 2 x 4) was devised for eight outdoor un-vegetated rain gardens to evaluate the effects of ...

  9. M-Split: A Graphical User Interface to Analyze Multilayered Anisotropy from Shear Wave Splitting

    Science.gov (United States)

    Abgarmi, Bizhan; Ozacar, A. Arda

    2017-04-01

    Shear wave splitting analysis are commonly used to infer deep anisotropic structure. For simple cases, obtained delay times and fast-axis orientations are averaged from reliable results to define anisotropy beneath recording seismic stations. However, splitting parameters show systematic variations with back azimuth in the presence of complex anisotropy and cannot be represented by average time delay and fast axis orientation. Previous researchers had identified anisotropic complexities at different tectonic settings and applied various approaches to model them. Most commonly, such complexities are modeled by using multiple anisotropic layers with priori constraints from geologic data. In this study, a graphical user interface called M-Split is developed to easily process and model multilayered anisotropy with capabilities to properly address the inherited non-uniqueness. M-Split program runs user defined grid searches through the model parameter space for two-layer anisotropy using formulation of Silver and Savage (1994) and creates sensitivity contour plots to locate local maximas and analyze all possible models with parameter tradeoffs. In order to minimize model ambiguity and identify the robust model parameters, various misfit calculation procedures are also developed and embedded to M-Split which can be used depending on the quality of the observations and their back-azimuthal coverage. Case studies carried out to evaluate the reliability of the program using real noisy data and for this purpose stations from two different networks are utilized. First seismic network is the Kandilli Observatory and Earthquake research institute (KOERI) which includes long term running permanent stations and second network comprises seismic stations deployed temporary as part of the "Continental Dynamics-Central Anatolian Tectonics (CD-CAT)" project funded by NSF. It is also worth to note that M-Split is designed as open source program which can be modified by users for

  10. Fitting diameter distribution models to data from forest inventories with concentric plot design

    Directory of Open Access Journals (Sweden)

    Nikos Nanos

    2017-10-01

    Research highlights:We designed a new method to fit the Weibull distribution to forest inventory data from concentric plots that achieves high accuracy and precision in parameter estimates regardless of the within-plot spatial tree pattern.

  11. Rank-based permutation approaches for non-parametric factorial designs.

    Science.gov (United States)

    Umlauft, Maria; Konietschke, Frank; Pauly, Markus

    2017-11-01

    Inference methods for null hypotheses formulated in terms of distribution functions in general non-parametric factorial designs are studied. The methods can be applied to continuous, ordinal or even ordered categorical data in a unified way, and are based only on ranks. In this set-up Wald-type statistics and ANOVA-type statistics are the current state of the art. The first method is asymptotically exact but a rather liberal statistical testing procedure for small to moderate sample size, while the latter is only an approximation which does not possess the correct asymptotic α level under the null. To bridge these gaps, a novel permutation approach is proposed which can be seen as a flexible generalization of the Kruskal-Wallis test to all kinds of factorial designs with independent observations. It is proven that the permutation principle is asymptotically correct while keeping its finite exactness property when data are exchangeable. The results of extensive simulation studies foster these theoretical findings. A real data set exemplifies its applicability. © 2017 The British Psychological Society.

  12. Factorial Design Approach in Proportioning Prestressed Self-Compacting Concrete.

    Science.gov (United States)

    Long, Wu-Jian; Khayat, Kamal Henri; Lemieux, Guillaume; Xing, Feng; Wang, Wei-Lun

    2015-03-13

    In order to model the effect of mixture parameters and material properties on the hardened properties of, prestressed self-compacting concrete (SCC), and also to investigate the extensions of the statistical models, a factorial design was employed to identify the relative significance of these primary parameters and their interactions in terms of the mechanical and visco-elastic properties of SCC. In addition to the 16 fractional factorial mixtures evaluated in the modeled region of -1 to +1, eight axial mixtures were prepared at extreme values of -2 and +2 with the other variables maintained at the central points. Four replicate central mixtures were also evaluated. The effects of five mixture parameters, including binder type, binder content, dosage of viscosity-modifying admixture (VMA), water-cementitious material ratio (w/cm), and sand-to-total aggregate ratio (S/A) on compressive strength, modulus of elasticity, as well as autogenous and drying shrinkage are discussed. The applications of the models to better understand trade-offs between mixture parameters and carry out comparisons among various responses are also highlighted. A logical design approach would be to use the existing model to predict the optimal design, and then run selected tests to quantify the influence of the new binder on the model.

  13. Accelerator design of the KEK B-Factory

    International Nuclear Information System (INIS)

    Kurokawa, Shin-ichi; Satoh, Kotaro; Kikutani, Eiji

    1991-03-01

    A design study has been made for the KEK B-Factory, an accelerator complex dedicated to the detection of the CP-violation effect of B-mesons. It is an asymmetric two-ring electron-positron collider of 3.5x8 GeV within a new tunnel measuring 1273 m circumference. The design peak luminosity is to be 10 34 cm -2 s -1 , which will be realized in two steps. The luminosity is to be 2 x 10 33 cm -2 s -1 with a head-on collision scheme in the first step; it is then increased to a final value of 10 34 cm -2 s -1 with a finite-angle crossing scheme. This document comprises two parts; the first part presents an overview of the design; the second part is a collection of papers giving detailed descriptions of various subjects. Stress is put on the design of the first step; the second step is mentioned when necessary. (author)

  14. Dynamic Supply Chain Design and Operations Plan for Connected Smart Factories with Additive Manufacturing

    Directory of Open Access Journals (Sweden)

    Byung Do Chung

    2018-04-01

    Full Text Available Interest in smart factories and smart supply chains has been increasing, and researchers have emphasized the importance and the effects of advanced technologies such as 3D printers, the Internet of Things, and cloud services. This paper considers an innovation in dynamic supply-chain design and operations: connected smart factories that share interchangeable processes through a cloud-based system for personalized production. In the system, customers are able to upload a product design file, an optimal supply chain design and operations plan are then determined based on the available resources in the network of smart factories. The concept of smart supply chains is discussed and six types of flexibilities are identified, namely: design flexibility, product flexibility, process flexibility, supply chain flexibility, collaboration flexibility, and strategic flexibility. Focusing on supply chain flexibility, a general planning framework and various optimization models for dynamic supply chain design and operations plan are proposed. Further, numerical experiments are conducted to analyze fixed, production, and transportation costs for various scenarios. The results demonstrate the extent of the dynamic supply chain design and operations problem, and the large variation in transportation cost.

  15. Radiation safety design of super KEKB factory

    International Nuclear Information System (INIS)

    Sanami, Toshiya

    2015-01-01

    The SuperKEKB factory, which was scheduled to start operation early 2015, is an electron-positron collider designed to produce an 80x10"3"4-1/cm"2/s luminosity, which is 40 times greater than the KEKB factory. Built to investigate CP violation and 'new physics' beyond the Standard Model, the facility consists of a 7-GeV electron/3.5-GeV positron linac, a 1.1- GeV positron damping ring, beam transport, and a 7-GeV electron/4-GeV positron collider. To meet this level of luminosity, the collider will be operated with a small beam size and a large crossing angle at the interaction point. According to particle tracking simulations, beam losses under these conditions will be 35 times more than those previously operated. To help optimise shielding configurations, leakage radiation and induced activity are estimated through empirical equations and detailed Monte-Carlo simulations using MARS15 code for the interaction region, beam halo collimators, emergency pathways, ducts, forward direction tunnels, and positron production target. Examples of shielding strategies are presented to reduce both leakage dose and airborne activity for several locations in the facility. (authors)

  16. Interim Design Report for the International Design Study for a Neutrino Factory

    International Nuclear Information System (INIS)

    Choubey, S.; Gandhi, R.; Goswami, S.; Berg, J.S.; Fernow, R.; Gallardo, J.C.; Gupta, R.; Kirk, H.; Simos, N.; Souchlas, N.; Ellis, M.

    2011-01-01

    The starting point for the International Design Study for the Neutrino Factory (the IDS-NF) was the output of the earlier International Scoping Study for a future Neutrino Factory and super-beam facility (the ISS). The accelerator facility described in section 2 incorporates the improvements that have been derived from the substantial amount of work carried out within the Accelerator Working Group. Highlights of these improvements include: (1) Initial concepts for the implementation of the proton driver at each of the three example sites, CERN, FNAL, and RAL; (2) Detailed studies of the energy deposition in the target area; (3) A reduction in the length of the muon beam phase-rotation and bunching systems; (4) Detailed analyses of the impact of the risk that stray magnetic field in the accelerating cavities in the ionization cooling channel will reduce the maximum operating gradient. Several alternative ionization-cooling lattices have been developed as fallback options to mitigate this technical risk; (5) Studies of particle loss in the muon front-end and the development of strategies to mitigate the deleterious effects of such losses; (6) The development of more complete designs for the muon linac and re-circulating linacs; (7) The development of a design for the muon FFAG that incorporates insertions for injection and extraction; and (8) Detailed studies of diagnostics in the decay ring. Other sub-systems have undergone a more 'incremental' evolution; an indication that the design of the Neutrino Factory has achieved a degree of maturity. The design of the neutrino detectors described in section 3 has been optimized and the Detector Working Group has made substantial improvements to the simulation and analysis of the Magnetized Iron Neutrino Detector (MIND) resulting in an improvement in the overall neutrino-detection efficiency and a reduction in the neutrino-energy threshold. In addition, initial consideration of the engineering of the MIND has generated a

  17. Systems analysis and futuristic designs of advanced biofuel factory concepts.

    Energy Technology Data Exchange (ETDEWEB)

    Chianelli, Russ; Leathers, James; Thoma, Steven George; Celina, Mathias C.; Gupta, Vipin P.

    2007-10-01

    The U.S. is addicted to petroleum--a dependency that periodically shocks the economy, compromises national security, and adversely affects the environment. If liquid fuels remain the main energy source for U.S. transportation for the foreseeable future, the system solution is the production of new liquid fuels that can directly displace diesel and gasoline. This study focuses on advanced concepts for biofuel factory production, describing three design concepts: biopetroleum, biodiesel, and higher alcohols. A general schematic is illustrated for each concept with technical description and analysis for each factory design. Looking beyond current biofuel pursuits by industry, this study explores unconventional feedstocks (e.g., extremophiles), out-of-favor reaction processes (e.g., radiation-induced catalytic cracking), and production of new fuel sources traditionally deemed undesirable (e.g., fusel oils). These concepts lay the foundation and path for future basic science and applied engineering to displace petroleum as a transportation energy source for good.

  18. Thermal-hydraulic mixing in the split-core ANS reactor design

    International Nuclear Information System (INIS)

    Dorning, R.J.J.

    1988-01-01

    A design has been proposed for the advanced neutron source (ANS) reactor that incorporates a split core, one purpose of which is to create a mixing plenum between the upper and lower cores. It was hoped that in addition to introducing various desirable neutronics features, such as decreasing the fast neutron flux contamination of thermal and cold neutron beams located in the reactor midplane, this mixing plenum would make possible higher operating powers by lowering the maximum core temperature. This lower temperature was to be achieved as a result of the mixing, of the hot D 2 O coolant exiting the upper-core channels, and the cold D 2 O leaving the large upper core bypass. It was expected that this mixing would bring about a significantly reduced lower core maximum coolant inlet temperature. The authors have carried out large-scale computer calculations to determine the extent to which this mixing occurs in current split-core design geometry, which does not incorporate baffles, mixing devices, or other design features introduced to enhance mixing. The large-scale self-consistent calculations summarized here indicate that innovative design ideas to enhance mixing will be necessary if the split-core concept is to achieve the amount of thermal mixing needed to make possible significantly higher power operation and corresponding higher flux sources

  19. Industry 4.0 learning factory didactic design parameters for industrial engineering education in South Africa

    OpenAIRE

    Sackey, S. M.; Bester, A.; Adams, D.

    2017-01-01

    To manage the impact of Industry 4.0 on industrial engineering (IE) education curriculum requirements, realistic teaching and learning infrastructure such as a learning factory are required. This paper scans the literature to determine Industry 4.0’s principles and interactions with IE and a learning factory, surveys relevant universities by questionnaire to determine its current status and practices, and formulates didactic design parameters for an Industry 4.0 learning factory to support IE...

  20. Alveolar Ridge Split Technique Using Piezosurgery with Specially Designed Tips

    Directory of Open Access Journals (Sweden)

    Alessandro Moro

    2017-01-01

    Full Text Available The treatment of patients with atrophic ridge who need prosthetic rehabilitation is a common problem in oral and maxillofacial surgery. Among the various techniques introduced for the expansion of alveolar ridges with a horizontal bone deficit is the alveolar ridge split technique. The aim of this article is to give a description of some new tips that have been specifically designed for the treatment of atrophic ridges with transversal bone deficit. A two-step piezosurgical split technique is also described, based on specific osteotomies of the vestibular cortex and the use of a mandibular ramus graft as interpositional graft. A total of 15 patients were treated with the proposed new tips by our department. All the expanded areas were successful in providing an adequate width and height to insert implants according to the prosthetic plan and the proposed tips allowed obtaining the most from the alveolar ridge split technique and piezosurgery. These tips have made alveolar ridge split technique simple, safe, and effective for the treatment of horizontal and vertical bone defects. Furthermore the proposed piezosurgical split technique allows obtaining horizontal and vertical bone augmentation.

  1. Alveolar Ridge Split Technique Using Piezosurgery with Specially Designed Tips.

    Science.gov (United States)

    Moro, Alessandro; Gasparini, Giulio; Foresta, Enrico; Saponaro, Gianmarco; Falchi, Marco; Cardarelli, Lorenzo; De Angelis, Paolo; Forcione, Mario; Garagiola, Umberto; D'Amato, Giuseppe; Pelo, Sandro

    2017-01-01

    The treatment of patients with atrophic ridge who need prosthetic rehabilitation is a common problem in oral and maxillofacial surgery. Among the various techniques introduced for the expansion of alveolar ridges with a horizontal bone deficit is the alveolar ridge split technique. The aim of this article is to give a description of some new tips that have been specifically designed for the treatment of atrophic ridges with transversal bone deficit. A two-step piezosurgical split technique is also described, based on specific osteotomies of the vestibular cortex and the use of a mandibular ramus graft as interpositional graft. A total of 15 patients were treated with the proposed new tips by our department. All the expanded areas were successful in providing an adequate width and height to insert implants according to the prosthetic plan and the proposed tips allowed obtaining the most from the alveolar ridge split technique and piezosurgery. These tips have made alveolar ridge split technique simple, safe, and effective for the treatment of horizontal and vertical bone defects. Furthermore the proposed piezosurgical split technique allows obtaining horizontal and vertical bone augmentation.

  2. Experimental burn plot trial in the Kruger National Park: history, experimental design and suggestions for data analysis

    Directory of Open Access Journals (Sweden)

    R. Biggs

    2003-12-01

    Full Text Available The experimental burn plot (EBP trial initiated in 1954 is one of few ongoing long-termfire ecology research projects in Africa. The trial aims to assess the impacts of differentfire regimes in the Kruger National Park. Recent studies on the EBPs have raised questions as to the experimental design of the trial, and the appropriate model specificationwhen analysing data. Archival documentation reveals that the original design was modified on several occasions, related to changes in the park's fire policy. These modifications include the addition of extra plots, subdivision of plots and changes in treatmentsover time, and have resulted in a design which is only partially randomised. The representativity of the trial plots has been questioned on account of their relatively small size,the concentration of herbivores on especially the frequently burnt plots, and soil variation between plots. It is suggested that these factors be included as covariates inexplanatory models or that certain plots be excluded from data analysis based on resultsof independent studies of these factors. Suggestions are provided for the specificationof the experimental design when analysing data using Analysis of Variance. It is concluded that there is no practical alternative to treating the trial as a fully randomisedcomplete block design.

  3. Experimental strategies in carrying out VCU for tobacco crop I: plot design and size.

    Science.gov (United States)

    Toledo, F H R B; Ramalho, M A P; Pulcinelli, C E; Bruzi, A T

    2013-09-19

    We aimed to establish standards for tobacco Valor de Cultivo e Uso (VCU) in Brazil. We obtained information regarding the size and design of plots of two varietal groups of tobacco (Virginia and Burley). Ten inbred lines of each varietal group were evaluated in a randomized complete block design with four replications. The plot contained 42 plants with six rows of seven columns each. For each experiment plant, considering the position of the respective plant in the plot (row and column) as a reference, cured leaf weight (g/plant), total sugar content (%), and total alkaloid content (%) were determined. The maximum curvature of the variations in coefficients was estimated. Trials with the number of plants per plot ranging from 2 to 41 were simulated. The use of a border was not justified because the interactions between inbred lines x position in the plots were never significant, showing that the behavior of the inbred lines coincided with the different positions. The plant performance varied according to the column position in the plot. To lessen the effect of this factor, the use of plots with more than one row is recommended. Experimental precision, evaluated by the CV%, increased with an increase in plot size; nevertheless, the maximum curvature of the variation coefficient method showed no expressive increase in precision if the number of plants was greater than seven. The result in identification of the best inbred line, in terms of the size of each plot, coincided with the maximum curvature method.

  4. Fractional factorial plans

    CERN Document Server

    Dey, Aloke

    2009-01-01

    A one-stop reference to fractional factorials and related orthogonal arrays.Presenting one of the most dynamic areas of statistical research, this book offers a systematic, rigorous, and up-to-date treatment of fractional factorial designs and related combinatorial mathematics. Leading statisticians Aloke Dey and Rahul Mukerjee consolidate vast amounts of material from the professional literature--expertly weaving fractional replication, orthogonal arrays, and optimality aspects. They develop the basic theory of fractional factorials using the calculus of factorial arrangements, thereby providing a unified approach to the study of fractional factorial plans. An indispensable guide for statisticians in research and industry as well as for graduate students, Fractional Factorial Plans features: * Construction procedures of symmetric and asymmetric orthogonal arrays. * Many up-to-date research results on nonexistence. * A chapter on optimal fractional factorials not based on orthogonal arrays. * Trend-free plans...

  5. Nonlinear Dot Plots.

    Science.gov (United States)

    Rodrigues, Nils; Weiskopf, Daniel

    2018-01-01

    Conventional dot plots use a constant dot size and are typically applied to show the frequency distribution of small data sets. Unfortunately, they are not designed for a high dynamic range of frequencies. We address this problem by introducing nonlinear dot plots. Adopting the idea of nonlinear scaling from logarithmic bar charts, our plots allow for dots of varying size so that columns with a large number of samples are reduced in height. For the construction of these diagrams, we introduce an efficient two-way sweep algorithm that leads to a dense and symmetrical layout. We compensate aliasing artifacts at high dot densities by a specifically designed low-pass filtering method. Examples of nonlinear dot plots are compared to conventional dot plots as well as linear and logarithmic histograms. Finally, we include feedback from an expert review.

  6. High-gravity brewing utilizing factorial design

    Directory of Open Access Journals (Sweden)

    R. B. Almeida

    2000-06-01

    Full Text Available A number of factors can influence the behavior of yeast during fermentation. Some of these factors (initial wort concentration, initial pH and percentage of corn syrup in the composition of the wort were studied in order to determine their influence on the productivity of fermentation. Fermentations were carried out at 25ºC utilizing a 2³ factorial design of these factors. The results showed that the percentage of corn syrup had no influence on process productivity, whereas initial pH and especially initial wort concentration did. It can be concluded that using pH and initial wort concentration values higher than those utilized in this work (5.5 and 20ºP, respectively will result in a higher productivity.

  7. Interim Design Report for the International Design Study for a Neutrino Factory

    Energy Technology Data Exchange (ETDEWEB)

    Choubey, S.; Gandhi, R.; Goswami, S.; /Harish-Chandra Res. Inst.; Berg, J.S.; Fernow, R.; Gallardo, J.C.; Gupta, R.; Kirk, H.; Simos, N.; Souchlas, N.; /Brookhaven; Ellis, M.; /Brunel U. /CERN /Durham U., IPPP /Fermilab /Geneva U. /Glasgow U. /Heidelberg, Max Planck Inst. /Imperial Coll., London /Jefferson Lab /Saha Inst.

    2011-10-01

    The starting point for the International Design Study for the Neutrino Factory (the IDS-NF) was the output of the earlier International Scoping Study for a future Neutrino Factory and super-beam facility (the ISS). The accelerator facility described in section 2 incorporates the improvements that have been derived from the substantial amount of work carried out within the Accelerator Working Group. Highlights of these improvements include: (1) Initial concepts for the implementation of the proton driver at each of the three example sites, CERN, FNAL, and RAL; (2) Detailed studies of the energy deposition in the target area; (3) A reduction in the length of the muon beam phase-rotation and bunching systems; (4) Detailed analyses of the impact of the risk that stray magnetic field in the accelerating cavities in the ionization cooling channel will reduce the maximum operating gradient. Several alternative ionization-cooling lattices have been developed as fallback options to mitigate this technical risk; (5) Studies of particle loss in the muon front-end and the development of strategies to mitigate the deleterious effects of such losses; (6) The development of more complete designs for the muon linac and re-circulating linacs; (7) The development of a design for the muon FFAG that incorporates insertions for injection and extraction; and (8) Detailed studies of diagnostics in the decay ring. Other sub-systems have undergone a more 'incremental' evolution; an indication that the design of the Neutrino Factory has achieved a degree of maturity. The design of the neutrino detectors described in section 3 has been optimized and the Detector Working Group has made substantial improvements to the simulation and analysis of the Magnetized Iron Neutrino Detector (MIND) resulting in an improvement in the overall neutrino-detection efficiency and a reduction in the neutrino-energy threshold. In addition, initial consideration of the engineering of the MIND has

  8. Industry 4.0 learning factory didactic design parameters for industrial engineering education in South Africa

    Directory of Open Access Journals (Sweden)

    Sackey, S. M.

    2017-05-01

    Full Text Available To manage the impact of Industry 4.0 on industrial engineering (IE education curriculum requirements, realistic teaching and learning infrastructure such as a learning factory are required. This paper scans the literature to determine Industry 4.0’s principles and interactions with IE and a learning factory, surveys relevant universities by questionnaire to determine its current status and practices, and formulates didactic design parameters for an Industry 4.0 learning factory to support IE education in South Africa, making use of existing models of cyber-physical systems and learning factory morphology. In other results, the technical universities are discovered to be more positively disposed, in general terms, to developing an Industry 4.0 learning factory than are the traditional programmes which, with one exception, prefer computational facilities. Of ten universities that offer IE, only one — a traditional programme — has made significant progress towards creating an Industry 4.0 learning factory.

  9. RF system design for the PEP-II B Factory

    International Nuclear Information System (INIS)

    Schwarz, H.; Rimmer, R.

    1994-06-01

    The paper presents an overview of the design of the RF system for the PEP-II B Factory. An RF station consists of either two or four single-cell cavities driven by a 1.2 MW klystron through a waveguide distribution network. A variety of feedback loops stabilize the RF and its interaction with the beam. System parameters and all the relevant parameters of klystron and cavities are given

  10. Two ways factorial design for round robin test of anemometers

    International Nuclear Information System (INIS)

    Cuerva, A.

    1998-01-01

    This work presents a way to carry out an inter-comparison between different cup anemometers that are tested in different wind tunnels. The method applied is known as Factorial design and allows determining the influence in the test of different factors in this case the anemometer itself and the wind tunnel where it is tested. (Author) 4 refs

  11. Two Ways Factorial Design for round robin test of anemometers

    Energy Technology Data Exchange (ETDEWEB)

    Cuerva, A.

    1998-07-01

    This work presents a way to carry out an inter-comparison between different cup anemometers that are tested in different wind tunnels. The method applied is known as Factorial design and allows determining the influence in the test of different factors in this case the anemometer itself and the wind tunnel where it is tested. (Author) 4 refs.

  12. Assessment of the recycling potential of fresh concrete waste using a factorial design of experiments.

    Science.gov (United States)

    Correia, S L; Souza, F L; Dienstmann, G; Segadães, A M

    2009-11-01

    Recycling of industrial wastes and by-products can help reduce the cost of waste treatment prior to disposal and eventually preserve natural resources and energy. To assess the recycling potential of a given waste, it is important to select a tool capable of giving clear indications either way, with the least time and work consumption, as is the case of modelling the system properties using the results obtained from statistical design of experiments. In this work, the aggregate reclaimed from the mud that results from washout and cleaning operations of fresh concrete mixer trucks (fresh concrete waste, FCW) was recycled into new concrete with various water/cement ratios, as replacement of natural fine aggregates. A 3(2) factorial design of experiments was used to model fresh concrete consistency index and hardened concrete water absorption and 7- and 28-day compressive strength, as functions of FCW content and water/cement ratio, and the resulting regression equations and contour plots were validated with confirmation experiments. The results showed that the fresh concrete workability worsened with the increase in FCW content but the water absorption (5-10 wt.%), 7-day compressive strength (26-36 MPa) and 28-day compressive strength (32-44 MPa) remained within the specified ranges, thus demonstrating that the aggregate reclaimed from FCW can be recycled into new concrete mixtures with lower natural aggregate content.

  13. Phenomenology of scaled factorial moments and future approaches for correlation studies

    International Nuclear Information System (INIS)

    Seibert, D.

    1991-01-01

    We show that the definitions of the exclusive and inclusive scaled factorial moments are not equivalent, and propose the use of scaled factorial moments that reduce to the exclusive moments in the case of fixed multiplicity. We then present a new derivation of the multiplicity scaling law for scaled factorial moment data. This scaling law seems to hold, independent of collision energy, for events with fixed projectile and target. However, deviations from this scaling law indicate that correlations in S-Au collisions are 30 times as strong as correlations in hadronic collisions. Finally, we discuss 'split-bin' correlation functions, the most useful tool for future investigations of these anomalously strong hadronic correlations. (orig.)

  14. Magnet design studies for the TRIUMF KAON factory proposal

    International Nuclear Information System (INIS)

    Otter, A.J.; Ellstrom, L.; Haddock, C.; Harold, M.; Reeve, P.; Sasaki, H.; Schwandt, P.

    1989-10-01

    TRIUMF is engaged on a one year Project Definition Study of its KAON factory proposal. This proposal calls for a total of 1800 magnets to be installed in three storage rings, two synchrotrons, beam transfer lines and experimental facilities to increase the present beam from 200 μA at 500 MeV to 100 μA at 30 GeV. The paper discusses the current design status concentrating on the ac booster synchrotron ring magnets which will be driven by biased dc current modulated at 50 Hz. Methods of estimating the core losses for this excitation, the coil eddy current losses and design and fabrication features of prototypes will be presented

  15. Application of Factorial Design for Gas Parameter Optimization in CO2 Laser Welding

    DEFF Research Database (Denmark)

    Gong, Hui; Dragsted, Birgitte; Olsen, Flemming Ove

    1997-01-01

    The effect of different gas process parameters involved in CO2 laser welding has been studied by applying two-set of three-level complete factorial designs. In this work 5 gas parameters, gas type, gas flow rate, gas blowing angle, gas nozzle diameter, gas blowing point-offset, are optimized...... to be a very useful tool for parameter optimi-zation in laser welding process. Keywords: CO2 laser welding, gas parameters, factorial design, Analysis of Variance........ The bead-on-plate welding specimens are evaluated by a number of quality char-acteristics, such as the penetration depth and the seam width. The significance of the gas pa-rameters and their interactions are based on the data found by the Analysis of Variance-ANOVA. This statistic methodology is proven...

  16. From field to factory-Taking advantage of shop manufacturing for the pebble bed modular reactor

    International Nuclear Information System (INIS)

    Wallace, Edward; Matzie, Regis; Heiderd, Roger; Maddalena, John

    2006-01-01

    The move of nuclear plant construction from the field to the factory for small, advanced pebble bed modular reactor (PBMR) designs has significant benefits compared to traditional light water reactor (LWR) field oriented designs. The use of modular factory construction techniques has a growing economic benefit over time through well-established process learning applications. This paper addresses the basic PBMR design objectives and commercialization model that drive this approach; provides a brief technical description of the PBMR design and layout with representative CAD views and discusses derived figures of merit highlighting the relative simplicity of PBMR compared to a modern LWR. The discussion emphasizes that more of PBMR can be built in the factory due to the simple design of a direct helium Brayton cycle compared to an indirect LWR steam cycle with its associated equipment. For the PBMR design there are fewer and less cumbersome auxiliary and safety systems with their attendant support requirements. Additionally, the labor force economic efficiency for nuclear projects is better in the factory than in the field, including consideration of labor costs and nuclear quality programs. Industrial learning is better in the factory because of the more controlled environment, mechanization optimization opportunities and because of the more stable labor force compared to the field. Supply chain benefits are more readily achievable with strategic contracts for module suppliers. Although building a nuclear power plant is not a typical high volume manufacturing process, for the PBMR-type of plant, with its high degree of standardization and relatively small, simplified design, the shift to factory work has a significant impact on overall project cost due to earlier identification and better coordination of parallel construction paths. This is in stark contrast to the construction of a large LWR in the past. Finally, the PBMR modular plant concept continues at the

  17. A Computer Program for Drip Irrigation System Design for Small Plots

    Science.gov (United States)

    Philipova, Nina; Nicheva, Olga; Kazandjiev, Valentin; Chilikova-Lubomirova, Mila

    2012-12-01

    A computer programhas been developed for design of surface drip irrigation system. It could be applied for calculation of small scale fields with an area up to 10 ha. The program includes two main parts: crop water requirements and hydraulic calculations of the system. It has been developed in Graphical User Interface in MATLAB and gives opportunity for selecting some parameters from tables such as: agro- physical soil properties, characteristics of the corresponding crop, climatic data. It allows the user of the program to assume and set a definite value, for example the emitter discharge, plot parameters and etc. Eight cases of system layout according to the water source layout and the number of plots of the system operation are laid into hydraulic section of the program. It includes the design of lateral, manifold, main line and pump calculations. The program has been compiled to work in Windows.

  18. AutoPyFactory: A Scalable Flexible Pilot Factory Implementation

    CERN Document Server

    Caballero, J; The ATLAS collaboration; Love, P; Stewart, G

    2012-01-01

    The ATLAS experiment at the CERN LHC is one of the largest users of grid computing infrastructure, which is a central part of the experiment’s computing operations. Considerable efforts have been made to use grid technology in the most efficient and effective way, including the use of a pilot job based workload management framework. In this model the experiment submits ’pilot’ jobs to sites without payload. When these jobs begin to run they contact a central service to retrieve a real payload to execute. The first generation of pilot factories were usually specific to a single VO, and were bound to the particular architecture of that VO’s distributed processing. A second generation provides factories which are more flexible, not tied to any particular VO, and provide new or improved features such as monitoring, logging, profiling, etc. In this paper we describe this key part of the ATLAS pilot architecture, a second generation pilot factory, AutoPyFactory. AutoPyFactory has a modular design and is hig...

  19. Load Sharing Multiobjective Optimization Design of a Split Torque Helicopter Transmission

    Directory of Open Access Journals (Sweden)

    Chenxi Fu

    2015-01-01

    Full Text Available Split torque designs can offer significant advantages over the traditional planetary designs for helicopter transmissions. However, it has two unique properties, gap and phase differences, which result in the risk of unequal load sharing. Various methods have been proposed to eliminate the effect of gap and promote load sharing to a certain extent. In this paper, system design parameters will be optimized to change the phase difference, thereby further improving load sharing. A nonlinear dynamic model is established to measure the load sharing with dynamic mesh forces quantitatively. Afterwards, a multiobjective optimization of a reference split torque design is conducted with the promoting of load sharing property, lightweight, and safety considered as the objectives. The load sharing property, which is measured by load sharing coefficient, is evaluated under multiple operating conditions with dynamic analysis method. To solve the multiobjective model with NSGA-II, an improvement is done to overcome the problem of time consuming. Finally, a satisfied optimal solution is picked up as the final design from the Pareto optimal front, which achieves improvements in all the three objectives compared with the reference design.

  20. FLP: a field line plotting code for bundle divertor design

    International Nuclear Information System (INIS)

    Ruchti, C.

    1981-01-01

    A computer code was developed to aid in the design of bundle divertors. The code can handle discrete toroidal field coils and various divertor coil configurations. All coils must be composed of straight line segments. The code runs on the PDP-10 and displays plots of the configuration, field lines, and field ripple. It automatically chooses the coil currents to connect the separatrix produced by the divertor to the outer edge of the plasma and calculates the required coil cross sections. Several divertor designs are illustrated to show how the code works

  1. Polarization Insensitivity in Double-Split Ring and Triple-Split Ring Terahertz Resonators

    International Nuclear Information System (INIS)

    Wu Qian-Nan; Lan Feng; Tang Xiao-Pin; Yang Zi-Qiang

    2015-01-01

    A modified double-split ring resonator and a modified triple-split ring resonator, which offer polarization-insensitive performance, are investigated, designed and fabricated. By displacing the two gaps of the conventional double-split ring resonator away from the center, the second resonant frequency for the 0° polarized wave and the resonant frequency for the 90° polarized wave become increasingly close to each other until they are finally identical. Theoretical and experimental results show that the modified double-split ring resonator and the modified triple-split ring resonator are insensitive to different polarized waves and show strong resonant frequency dips near 433 and 444 GHz, respectively. The results of this work suggest new opportunities for the investigation and design of polarization-dependent terahertz devices based on split ring resonators. (paper)

  2. Graphical Data Analysis on the Circle: Wrap-Around Time Series Plots for (Interrupted) Time Series Designs.

    Science.gov (United States)

    Rodgers, Joseph Lee; Beasley, William Howard; Schuelke, Matthew

    2014-01-01

    Many data structures, particularly time series data, are naturally seasonal, cyclical, or otherwise circular. Past graphical methods for time series have focused on linear plots. In this article, we move graphical analysis onto the circle. We focus on 2 particular methods, one old and one new. Rose diagrams are circular histograms and can be produced in several different forms using the RRose software system. In addition, we propose, develop, illustrate, and provide software support for a new circular graphical method, called Wrap-Around Time Series Plots (WATS Plots), which is a graphical method useful to support time series analyses in general but in particular in relation to interrupted time series designs. We illustrate the use of WATS Plots with an interrupted time series design evaluating the effect of the Oklahoma City bombing on birthrates in Oklahoma County during the 10 years surrounding the bombing of the Murrah Building in Oklahoma City. We compare WATS Plots with linear time series representations and overlay them with smoothing and error bands. Each method is shown to have advantages in relation to the other; in our example, the WATS Plots more clearly show the existence and effect size of the fertility differential.

  3. JINR tau-charm factory design study

    International Nuclear Information System (INIS)

    Perel'shtejn, E.; Aleksandrov, V.; Antropov, V.

    1993-01-01

    The review on tau-charm factory in JINR (Dubna) is presented. The structure scheme of tau-charm factory is described. The problems on injection complex are discussed: the composition, the working regime and parameters. The magnetic lattice of a booster is described. A versatile magnet lattice is used in tau-charm collider. It can realize both conventional flat beam scheme and monochromatization scheme. The results of chromaticity correction in high emittance lattice are presented. The list of parameters of tau-charm collider is given. The technical proposal of magnetic elements of booster and collider and their power supplies is made, as well as RF power supply in collider and vacuum system in its periodic cell. 12 refs.; 12 figs.; 3 tabs

  4. Vacuum system design for the PEP-II B Factory High-Energy Ring

    International Nuclear Information System (INIS)

    Perkins, C.; Bostic, D.; Daly, E.

    1994-06-01

    The design of the vacuum system for the PEP-II B Factory High-Energy Ring is reviewed. The thermal design and vacuum requirements are particularly challenging in PEP-II due to high stored beam currents up to 3.0 amps in 1658 bunches. The vacuum chambers for the HER arcs are fabricated by electron beam welding extruded copper sections up to 6 m long. Design of these chambers and the vacuum PumPing configuration is described with results from vacuum and thermal analyses

  5. Fractional Factorial Design for Parameter Sweep Experiments Using Nimrod/E

    Directory of Open Access Journals (Sweden)

    T.C. Peachey

    2008-01-01

    Full Text Available The techniques of formal experimental design and analysis are powerful tools for scientists and engineers. However, these techniques are currently underused for experiments conducted with computer models. This has motivated the incorporation of experimental design functionality into the Nimrod tool chain. Nimrod has been extensively used for exploration of the response of models to their input parameters; the addition of experimental design tools will combine the efficiency of carefully designed experiments with the power of distributed execution. This paper describes the incorporation of one type of design, the fractional factorial design, and associated analysis tools, into the Nimrod framework. The result provides a convenient environment that automates the design of an experiment, the execution of the jobs on a computational grid and the return of results, and which assists in the interpretation of those results. Several case studies are included which demonstrate various aspects of this approach.

  6. Optimization of minoxidil microemulsions using fractional factorial design approach.

    Science.gov (United States)

    Jaipakdee, Napaphak; Limpongsa, Ekapol; Pongjanyakul, Thaned

    2016-01-01

    The objective of this study was to apply fractional factorial and multi-response optimization designs using desirability function approach for developing topical microemulsions. Minoxidil (MX) was used as a model drug. Limonene was used as an oil phase. Based on solubility, Tween 20 and caprylocaproyl polyoxyl-8 glycerides were selected as surfactants, propylene glycol and ethanol were selected as co-solvent in aqueous phase. Experiments were performed according to a two-level fractional factorial design to evaluate the effects of independent variables: Tween 20 concentration in surfactant system (X1), surfactant concentration (X2), ethanol concentration in co-solvent system (X3), limonene concentration (X4) on MX solubility (Y1), permeation flux (Y2), lag time (Y3), deposition (Y4) of MX microemulsions. It was found that Y1 increased with increasing X3 and decreasing X2, X4; whereas Y2 increased with decreasing X1, X2 and increasing X3. While Y3 was not affected by these variables, Y4 increased with decreasing X1, X2. Three regression equations were obtained and calculated for predicted values of responses Y1, Y2 and Y4. The predicted values matched experimental values reasonably well with high determination coefficient. By using optimal desirability function, optimized microemulsion demonstrating the highest MX solubility, permeation flux and skin deposition was confirmed as low level of X1, X2 and X4 but high level of X3.

  7. Effects of amount and timing of nitrogen application and weed density on wild mustard (Sinapis arvensis seed production in winter wheat

    Directory of Open Access Journals (Sweden)

    mehdi rastgoo

    2009-06-01

    Full Text Available In order to study the effects of amount and timing of nitrogen application and weed density on wild mustard (Sinapis arvensis seed production in winter wheat, an experiment was conducted in 2001 at Research station of college of agriculture, Ferdowsi University of Mashhad. A Split plot design with three replications were used with factorial combination of weed density (0, 8, 16, and 32 plant/m2 and nitrogen (low=100, optimum= 150, and high= 225 Kg/ha as main plots.The sub plot factor included nitrogen splitting pattern (P1=1/3 at planting time+2/3 at tillering, P2= 1/3 at planting time + 1/3 at tillering + 1/3 at shooting. According to the results, wild mustard seed production increased with increasing wild mustard density and nitrogen rates, due to high wild mustard biomass production. Seed production of wild mustard was 161, 311, and 488 million/ha in low, optimum and high nitrogen rates, respectively. In the other hand, density and nitrogen rates had a significant effect on wild mustard fecundity. However, nitrogen splitting pattern showed no significant effect on wild mustard seed production.

  8. Factorial experimental design intended for the optimization of the alumina purification conditions

    Science.gov (United States)

    Brahmi, Mounaouer; Ba, Mohamedou; Hidri, Yassine; Hassen, Abdennaceur

    2018-04-01

    The objective of this study was to determine the optimal conditions by using the experimental design methodology for the removal of some impurities associated with the alumina. So, three alumina qualities of different origins were investigated under the same conditions. The application of full-factorial designs on the samples of different qualities of alumina has followed the removal rates of the sodium oxide. However, a factorial experimental design was developed to describe the elimination of sodium oxide associated with the alumina. The experimental results showed that chemical analyze followed by XRF prior treatment of the samples, provided a primary idea concerning these prevailing impurities. Therefore, it appeared that the sodium oxide constituted the largest amount among all impurities. After the application of experimental design, analysis of the effectors different factors and their interactions showed that to have a better result, we should reduce the alumina quantity investigated and by against increase the stirring time for the first two samples, whereas, it was necessary to increase the alumina quantity in the case of the third sample. To expand and improve this research, we should take into account all existing impurities, since we found during this investigation that the levels of partial impurities increased after the treatment.

  9. Selecting the optimum plot size for a California design-based stream and wetland mapping program.

    Science.gov (United States)

    Lackey, Leila G; Stein, Eric D

    2014-04-01

    Accurate estimates of the extent and distribution of wetlands and streams are the foundation of wetland monitoring, management, restoration, and regulatory programs. Traditionally, these estimates have relied on comprehensive mapping. However, this approach is prohibitively resource-intensive over large areas, making it both impractical and statistically unreliable. Probabilistic (design-based) approaches to evaluating status and trends provide a more cost-effective alternative because, compared with comprehensive mapping, overall extent is inferred from mapping a statistically representative, randomly selected subset of the target area. In this type of design, the size of sample plots has a significant impact on program costs and on statistical precision and accuracy; however, no consensus exists on the appropriate plot size for remote monitoring of stream and wetland extent. This study utilized simulated sampling to assess the performance of four plot sizes (1, 4, 9, and 16 km(2)) for three geographic regions of California. Simulation results showed smaller plot sizes (1 and 4 km(2)) were most efficient for achieving desired levels of statistical accuracy and precision. However, larger plot sizes were more likely to contain rare and spatially limited wetland subtypes. Balancing these considerations led to selection of 4 km(2) for the California status and trends program.

  10. AutoPyFactory: A Scalable Flexible Pilot Factory Implementation

    International Nuclear Information System (INIS)

    Caballero, J; Hover, J; Love, P; Stewart, G A

    2012-01-01

    The ATLAS experiment at the CERN LHC is one of the largest users of grid computing infrastructure, which is a central part of the experiment's computing operations. Considerable efforts have been made to use grid technology in the most efficient and effective way, including the use of a pilot job based workload management framework. In this model the experiment submits ‘pilot’ jobs to sites without payload. When these jobs begin to run they contact a central service to pick-up a real payload to execute. The first generation of pilot factories were usually specific to a single Virtual Organization (VO), and were bound to the particular architecture of that VO's distributed processing. A second generation provides factories which are more flexible, not tied to any particular VO, and provide new and improved features such as monitoring, logging, profiling, etc. In this paper we describe this key part of the ATLAS pilot architecture, a second generation pilot factory, AutoPyFactory. AutoPyFactory has a modular design and is highly configurable. It is able to send different types of pilots to sites and exploit different submission mechanisms and queue characteristics. It is tightly integrated with the PanDA job submission framework, coupling pilot flow to the amount of work the site has to run. It gathers information from many sources in order to correctly configure itself for a site and its decision logic can easily be updated. Integrated into AutoPyFactory is a flexible system for delivering both generic and specific job wrappers which can perform many useful actions before starting to run end-user scientific applications, e.g., validation of the middleware, node profiling and diagnostics, and monitoring. AutoPyFactory also has a robust monitoring system that has been invaluable in establishing a reliable pilot factory service for ATLAS.

  11. Optimization of MCM-48 synthesis using factorial design

    Energy Technology Data Exchange (ETDEWEB)

    Nascimento, A.R. do; Medeiros, R.L.B. de A.; Melo, M. A. de F.; Melo, D.M. de A. [Universitdade Federal do Rio Grande do Norte (UFRN), Natal (Brazil); Souza, M.J.B. de, E-mail: ale3ufs@yahoo.com.br [Universidade Federal de Sergipe (UFS), Sao Cristovao (Brazil)

    2016-10-15

    MCM-48 mesoporous materials were hydrothermally synthesized according to the 2{sup 2} factorial design by varying the crystallization time and temperature of the synthesis gel, and characterized by means of X-ray diffraction analysis and adsorption of N{sub 2} . In the crystallization temperature and time conditions used, specific areas between 924 to 1102 m{sup 2}.g{sup -1}, pore volumes between 0.015 to 0.087 cm{sup 3}.g{sup -1} and pore diameters between 3.2 to 4.0 nm were obtained. It was observed that for the syntheses performed at high temperature, the crystallization time should be reduced so that the material structure is formed. (author)

  12. Sterile neutrinos beyond LSND at the neutrino factory

    International Nuclear Information System (INIS)

    Meloni, Davide; Tang Jian; Winter, Walter

    2010-01-01

    We discuss the effects of one additional sterile neutrino at the Neutrino Factory. Compared to earlier analyses, which have been motivated by Liquid Scintillator Neutrino Detector (LSND) results, we do not impose any constraint on the additional mass squared splitting. This means that the additional mass eigenstate could, with small mixings, be located among the known ones, as it is suggested by the recent analysis of cosmological data. We use a self-consistent framework at the Neutrino Factory without any constraints on the new parameters. We demonstrate for a combined short and long baseline setup that near detectors can provide the expected sensitivity at the LSND-motivated Δm 41 2 -range, while some sensitivity can also be obtained in the region of the atmospheric mass splitting from the long baselines. We point out that limits on such very light sterile neutrinos may also be obtained from a reanalysis of atmospheric and solar neutrino oscillation data, as well as from supernova neutrino observations. In the second part of the analysis, we compare our sensitivity with the existing literature using additional assumptions, such as |Δm 41 2 |>>|Δm 31 2 |, leading to averaging of the fast oscillations in the far detectors. We demonstrate that while the Neutrino Factory has excellent sensitivity compared to existing studies using similar assumptions, one has to be very careful interpreting these results for a combined short and long baseline setup where oscillations could occur in the near detectors. We also test the impact of additional ν τ detectors at the short and long baselines, and we do not find a substantial improvement of the sensitivities.

  13. Urease inhibitor (NBPT and efficiency of single or split application of urea in wheat crop

    Directory of Open Access Journals (Sweden)

    Marcelo Curitiba Espindula

    2014-04-01

    Full Text Available NBPT (N-(n-butyl thiophosphoric triamide, a urease inhibitor, has been reported as one of the most promising compounds to maximize urea nitrogen use in agricultural systems. The objective of this study was to evaluate the performance of irrigated wheat fertilized with urea or urea + NBPT as single or split application. The experiment was conducted from June to October 2006 in Viçosa, MG, Brazil. The experimental design followed a 2×2 factorial scheme, in which urea or urea + NBPT were combined with two modes of application: full dose at sowing (60kg ha-1 or split (20kg ha-1 at sowing + 40kg ha-1 as topdressing at tillering, in randomized blocks with ten replications. The split application of nitrogen fertilization does not improve the yield wheat under used conditions. The use of urease inhibitor improves the grain yield of wheat crop when urea is applied in topdressing at tillering, but its use does not promote difference when urea is applied in the furrow at planting.

  14. Finite Element Analysis Design of a Split Rotor Bracket for a Bulb Turbine Generator

    Directory of Open Access Journals (Sweden)

    Yongyao Luo

    2013-01-01

    Full Text Available The rotor bracket is a key component of the generator rotor with cracks in the rotor bracket leading to rubbing between the rotor and stator, which threatens safe operation of the unit. The rotor rim is so complicated that the equivalent radial stiffness of rim was determined by numerical simulation other than engineering experience. A comprehensive numerical method including finite element analyses and the contact method for multibody dynamics has been used to design the split rotor bracket. The com-putational results showed that cracks would occur in the initial design of the bracket when the turbine operated at the runaway speed, and the bracket design should be improved. The improved design of the bracket was strong enough to avoid cracks and rub between the rotor and stator. This design experience will help improve the design of split rotor brackets for bulb turbine generators.

  15. Concentric Split Flow Filter

    Science.gov (United States)

    Stapleton, Thomas J. (Inventor)

    2015-01-01

    A concentric split flow filter may be configured to remove odor and/or bacteria from pumped air used to collect urine and fecal waste products. For instance, filter may be designed to effectively fill the volume that was previously considered wasted surrounding the transport tube of a waste management system. The concentric split flow filter may be configured to split the air flow, with substantially half of the air flow to be treated traveling through a first bed of filter media and substantially the other half of the air flow to be treated traveling through the second bed of filter media. This split flow design reduces the air velocity by 50%. In this way, the pressure drop of filter may be reduced by as much as a factor of 4 as compare to the conventional design.

  16. Thermodynamic analysis and system design of a novel split cycle engine concept

    International Nuclear Information System (INIS)

    Dong, Guangyu; Morgan, Robert E.; Heikal, Morgan R.

    2016-01-01

    The split cycle engine is a new reciprocating internal combustion engine with a potential of a radical efficiency improvement. In this engine, the compression and combustion–expansion processes occur in different cylinders. In the compression cylinder, the charge air is compressed through a quasi-isothermal process by direct cooling of the air. The high pressure air is then heated in a recuperator using the waste heat of exhaust gas before induction to the combustion cylinder. The combustion process occurs during the expansion stroke, in a quasi-isobaric process. In this paper, a fundamental theoretical cycle analysis and one-dimensional engine simulation of the split cycle engine was undertaken. The results show that the thermal efficiency (η) is mainly decided by the CR (compression ratio) and ER (expansion ratio), the regeneration effectiveness (σ), and the temperature rising ratio (N). Based on the above analysis, a system optimization of the engine was conducted. The results showed that by increasing CR from 23 to 25, the combustion and recuperation processes could be improved. By increasing the expansion ratio to 26, the heat losses during the gas exchange stroke were further reduced. Furthermore, the coolant temperatures of the compression and expansion chambers can be controlled separately to reduce the wall heat transfer losses. Compared to a conventional engine, a 21% total efficiency improvement was achieved when the split cycle was applied. It was concluded that through the system optimization, a total thermal efficiency of 53% can be achieved on split cycle engine. - Highlights: • Fundamental mechanism of the split cycle engine is investigated. • The key affecting factors of the thermodynamic cycle efficiency are identified. • The practical efficiency of split cycle applying on diesel engine is analysed. • The design optimization on the split cycle engine concept is conducted.

  17. SuperB A High-Luminosity Asymmetric $e^+ e^-$ Super Flavour Factory : Conceptual Design Report

    CERN Document Server

    Bona, M.; Grauges Pous, E.; Colangelo, P.; De Fazio, F.; Palano, A.; Manghisoni, M.; Re, V.; Traversi, G.; Eigen, G.; Venturini, M.; Soni, N.; Bruschi, M.; De Castro, S.; Faccioli, P.; Gabrieli, A.; Giacobbe, B.; Semprini Cesare, N.; Spighi, R.; Villa, M.; Zoccoli, A.; Hearty, C.; McKenna, J.; Soni, A.; Khan, A.; Barniakov, A.Y.; Barniakov, M.Y.; Blinov, V.E.; Druzhinin, V.P.; Golubev, V.B.; Kononov, S.A.; Koop, I.A.; Kravchenko, E.A.; Levichev, E.B.; Nikitin, S.A.; Onuchin, A.P.; Piminov, P.A.; Serednyakov, S.I.; Shatilov, D.N.; Skovpen, Y.I.; Solodov, E.A.; Cheng, C.H.; Echenard, B.; Fang, F.; Hitlin, D.J.; Porter, F.C.; Asner, D.M.; Pham, T.N.; Fleischer, R.; Giudice, G.F.; Hurth, T.; Mangano, M.; Mancinelli, G.; Meadows, B.T.; Schwartz, A.J.; Sokoloff, M.D.; Soffer, A.; Beard, C.D.; Haas, T.; Mankel, R.; Hiller, G.; Ball, P.; Pappagallo, M.; Pennington, M.R.; Gradl, W.; Playfer, S.; Abada, A.; Becirevic, D.; Descotes-Genon, S.; Pene, O.; Andreotti, D.; Andreotti, M.; Bettoni, D.; Bozzi, C.; Calabresi, R.; Cecchi, A.; Cibinetto, G.; Franchini, P.; Luppi, E.; Negrini, M.; Petrella, A.; Piemontese, L.; Prencipe, E.; Santoro, V.; Stancari, G.; Anulli, F.; Baldini-Ferroli, R.; Biagini, M.E.; Boscolo, M.; Calcaterra, A.; Drago, A.; Finocchiaro, G.; Guiducci, S.; Isidori, G.; Pacetti, S.; Patteri, P.; Peruzzi, I.M.; Piccolo, M.; Preger, M.A.; Raimondi, P.; Rama, M.; Vaccarezza, C.; Zallo, A.; Zobov, M.; De Sangro, R.; Buzzo, A.; Lo Vetere, M.; Macri, M.; Monge, M.R.; Passaggio, S.; Patrignani, C.; Robutti, E.; Tosi, S.; Matias, J.; Panduro Vazquez, W.; Borzumati, F.; Eyges, V.; Prell, S.A.; Pedlar, T.K.; Korpar, S.; Pestonik, R.; Staric, M.; Neubert, M.; Denig, A.G.; Nierste, U.; Agoh, T.; Ohmi, K.; Ohnishi, Y.; Fry, J.R.; Touramanis, C.; Wolski, A.; Golob, B.; Krizan, P.; Flaecher, H.; Bevan, A.J.; Di Lodovico, F.; George, K.A.; Barlow, R.; Lafferty, G.; Jawahery, A.; Roberts, D.A.; Simi, G.; Patel, P.M.; Robertson, S.H.; Lazzaro, A.; Palombo, F.; Kaidalov, A.; Buras, A.J.; Tarantino, C.; Buchalla, G.; Sanda, A.I.; D'Ambrosio, G.; Ricciardi, G.; Bigi, I.; Jessop, C.P.; Losecco, J.M.; Honscheid, K.; Arnaud, N.; Chehab, R.; Fedala, Y.; Polci, F.; Roudeau, P.; Sordini, V.; Soskov, V.; Stocchi, A.; Variola, A.; Vivoli, A.; Wormser, G.; Zomer, F.; Bertolin, A.; Brugnera, R.; Gagliardi, N.; Gaz, A.; Margoni, M.; Morandin, M.; Posocco, M.; Rotondo, M.; Simonetto, F.; Stroili, R.; Bonneaud, G.R.; Lombardo, V.; Calderini, G.; Ratti, L.; Speziali, V.; Biasini, M.; Covarelli, R.; Manoni, E.; Servoli, L.; Angelini, C.; Batignani, G.; Bettarini, S.; Bosi, F.; Carpinelli, M.; Cenci, R.; Cervelli, A.; Dell'Orso, M.; Forti, F.; Giannetti, P.; Giorgi, M.; Lusiani, A.; Marchiori, G.; Massa, M.; Mazur, M.A.; Morsani, F.; Neri, N.; Paoloni, E.; Raffaelli, F.; Rizzo, G.; Walsh, J.; Braun, V.; Lenz, A.; Adams, G.S.; Danko, I.Z.; Baracchini, E.; Bellini, F.; Cavoto, G.; D'Orazio, A.; Del Re, D.; Di Marco, E.; Faccini, R.; Ferrarotto, F.; Gaspero, Mario; Jackson, P.; Martinelli, G.; Mazzoni, M.A.; Morganti, Silvio; Piredda, G.; Renga, F.; Silvestrini, L.; Voena, C.; Catani, L.; Di Ciaccio, A.; Messi, R.; Santovetti, E.; Satta, A.; Ciuchini, M.; Lubicz, V.; Wilson, F.F.; Godang, R.; Chen, X.; Liu, H.; Park, W.; Purohit, M.; Trivedi, A.; White, R.M.; Wilson, J.R.; Allen, M.T.; Aston, D.; Bartoldus, R.; Brodsky, S.J.; Cai, Y.; Coleman, J.; Convery, M.R.; DeBarger, S.; Dingfelder, J.C.; Dubois-Felsmann, G.P.; Ecklund, S.; Fisher, A.S.; Haller, G.; Heifets, S.A.; Kaminski, J.; Kelsey, M.H.; Kocian, M.L.; Leith, D.W.G.S.; Li, N.; Luitz, S.; Luth, V.; MacFarlane, D.; Messner, R.; Muller, D.R.; Nosochkov, Y.; Novokhatski, A.; Pivi, M.; Ratcliff, B.N.; Roodman, A.; Schwiening, J.; Seeman, J.; Snyder, A.; Sullivan, M.; Va'Vra, J.; Wienands, U.; Wisniewski, W.; Stoeck, H.; Cheng, H.Y.; Li, H.N.; Keum, Y.Y.; Gronau, M.; Grossman, Y.; Bianchi, F.; Gamba, D.; Gambino, P.; Marchetto, F.; Menichetti, Ezio A.; Mussa, R.; Pelliccioni, M.; Dalla Betta, G.F.; Bomben, M.; Bosisio, L.; Cartaro, C.; Lanceri, L.; Vitale, L.; Azzolini, V.; Bernabeu, J.; Lopez-March, N.; Martinez-Vidal, F.; Milanes, D.A.; Oyanguren, A.; Paradisi, P.; Pich, A.; Sanchis-Lozano, M.A.; Kowalewski, Robert V.; Roney, J.M.; Back, J.J.; Gershon, T.J.; Harrison, P.F.; Latham, T.E.; Mohanty, G.B.; Petrov, A.A.; Pierini, M.; INFN

    2007-01-01

    The physics objectives of SuperB, an asymmetric electron-positron collider with a luminosity above 10^36/cm^2/s are described, together with the conceptual design of a novel low emittance design that achieves this performance with wallplug power comparable to that of the current B Factories, and an upgraded detector capable of doing the physics in the SuperB environment.

  18. Factorial design of a solar photocatalytic process to treatment of wastewater effluent

    Energy Technology Data Exchange (ETDEWEB)

    Francisco, Adriana Ribeiro; Paterniani, Jose Euclides Stipp [Universidade Estadual de Campinas (FEAGRI/UNICAMP), SP (Brazil). Fac. de Engenharia Agricola], E-mail: adriana.francisco@agr.unicamp.br; Kuwakino, Adriana Yuri [Universidade Estadual de Campinas (CESET/UNICAMP), Limeira, SP (Brazil). Centro Superior de Educacao Tecnologica

    2008-07-01

    Advanced treatments are attributed to improving the quality of various types of waste such as the sanitary wastewater. The heterogeneous photocatalysis is an alternative that allows to improve the effluents conditions. This is possible because many chemical compounds of environmental concern can be degraded using UV radiation on a semiconductor. However, to enable the efficiency of the process photocatalytic is necessary to conduct a study of optimization to establish favorable conditions between selected variables. The aim of this work was a reactor solar photocatalytic optimization using factorial design 2{sup k}, depending on variables: mass (TiO{sub 2}), time (min) and flow of air (L min{sup -1}), using as analytical response the removal of color. The experiment was conducted at the Faculty of Agricultural Engineering (FEAGRI) and it was used the sanitary wastewater of there. The results indicated that there were significant efficiency using combinations mass = 1000 mg L{sup -1}, time = 360 min and flow of air = 5 L min{sup -1}. In the calculations of factorial design, the time showed a marked positive effect of 7.76, while the flow of air, when in excess, had an inhibitor behavior, even getting positive effect. (author)

  19. Clustering Words to Match Conditions: An Algorithm for Stimuli Selection in Factorial Designs

    Science.gov (United States)

    Guasch, Marc; Haro, Juan; Boada, Roger

    2017-01-01

    With the increasing refinement of language processing models and the new discoveries about which variables can modulate these processes, stimuli selection for experiments with a factorial design is becoming a tough task. Selecting sets of words that differ in one variable, while matching these same words into dozens of other confounding variables…

  20. Design study of a 25.5-MHz split coaxial RFQ

    International Nuclear Information System (INIS)

    Arai, Shigeaki; Imanishi, Akira; Morimoto, Teruhisa; Shibuya, Shinji; Tojyo, Eiki; Tokuda, Noboru.

    1989-08-01

    A 25.5-MHz split coaxial RFQ with modulated vanes is now being fabricated. The RFQ, 2.1 m in length and 0.9 m in diameter, will accelerate ions with a charge-to-mass ratio greater than 1/30 from 1 keV/n up to 45.4 keV/n. The design works on beam dynamics and cavity fabrication are reported. (author)

  1. Divide and control: split design of multi-input DNA logic gates.

    Science.gov (United States)

    Gerasimova, Yulia V; Kolpashchikov, Dmitry M

    2015-01-18

    Logic gates made of DNA have received significant attention as biocompatible building blocks for molecular circuits. The majority of DNA logic gates, however, are controlled by the minimum number of inputs: one, two or three. Here we report a strategy to design a multi-input logic gate by splitting a DNA construct.

  2. Neutrino Factory

    CERN Document Server

    Bogomilov, M; Tsenov, R; Dracos, M; Bonesini, M; Palladino, V; Tortora, L; Mori, Y; Planche, T; Lagrange, J  B; Kuno, Y; Benedetto, E; Efthymiopoulos, I; Garoby, R; Gilardoini, S; Martini, M; Wildner, E; Prior, G; Blondel, A; Karadzhow, Y; Ellis, M; Kyberd, P; Bayes, R; Laing, A; Soler, F  J  P; Alekou, A; Apollonio, M; Aslaninejad, M; Bontoiu, C; Jenner, L  J; Kurup, A; Long, K; Pasternak, J; Zarrebini, A; Poslimski, J; Blackmore, V; Cobb, J; Tunnell, C; Andreopoulos, C; Bennett, J  R  J; Brooks, S; Caretta, O; Davenne, T; Densham, C; Edgecock, T  R; Fitton, M; Kelliher, D; Loveridge, P; McFarland, A; Machida, S; Prior, C; Rees, G; Rogers, C; Rooney, M; Thomason, J; Wilcox, D; Booth, C; Skoro, G; Back, J  J; Harrison, P; Berg, J  S; Fernow, R; Gallardo, J  C; Gupta, R; Kirk, H; Simos, N; Stratakis, D; Souchlas, N; Witte, H; Bross, A; Geer, S; Johnstone, C; Mokhov, N; Neuffer, D; Popovic, M; Strait, J; Striganov, S; Morfín, J  G; Wands, R; Snopok, P; Bogacz, S  A; Morozov, V; Roblin, Y; Cline, D; Ding, X; Bromberg, C; Hart, T; Abrams, R  J; Ankenbrandt, C  M; Beard, K  B; Cummings, M  A  C; Flanagan, G; Johnson, R  P; Roberts, T  J; Yoshikawa, C  Y; Graves, V  B; McDonald, K  T; Coney, L; Hanson, G

    2014-01-01

    The properties of the neutrino provide a unique window on physics beyond that described by the standard model. The study of subleading effects in neutrino oscillations, and the race to discover CP-invariance violation in the lepton sector, has begun with the recent discovery that $\\theta_{13} > 0$. The measured value of $\\theta_{13}$ is large, emphasizing the need for a facility at which the systematic uncertainties can be reduced to the percent level. The neutrino factory, in which intense neutrino beams are produced from the decay of muons, has been shown to outperform all realistic alternatives and to be capable of making measurements of the requisite precision. Its unique discovery potential arises from the fact that only at the neutrino factory is it practical to produce high-energy electron (anti)neutrino beams of the required intensity. This paper presents the conceptual design of the neutrino factory accelerator facility developed by the European Commission Framework Programme 7 EURO$\

  3. Design of a dual linear polarization antenna using split ring resonators at X-band

    Science.gov (United States)

    Ahmed, Sadiq; Chandra, Madhukar

    2017-11-01

    Dual linear polarization microstrip antenna configurations are very suitable for high-performance satellites, wireless communication and radar applications. This paper presents a new method to improve the co-cross polarization discrimination (XPD) for dual linear polarized microstrip antennas at 10 GHz. For this, three various configurations of a dual linear polarization antenna utilizing metamaterial unit cells are shown. In the first layout, the microstrip patch antenna is loaded with two pairs of spiral ring resonators, in the second model, a split ring resonator is placed between two microstrip feed lines, and in the third design, a complementary split ring resonators are etched in the ground plane. This work has two primary goals: the first is related to the addition of metamaterial unit cells to the antenna structure which permits compensation for an asymmetric current distribution flow on the microstrip antenna and thus yields a symmetrical current distribution on it. This compensation leads to an important enhancement in the XPD in comparison to a conventional dual linear polarized microstrip patch antenna. The simulation reveals an improvement of 7.9, 8.8, and 4 dB in the E and H planes for the three designs, respectively, in the XPD as compared to the conventional dual linear polarized patch antenna. The second objective of this paper is to present the characteristics and performances of the designs of the spiral ring resonator (S-RR), split ring resonator (SRR), and complementary split ring resonator (CSRR) metamaterial unit cells. The simulations are evaluated using the commercial full-wave simulator, Ansoft High-Frequency Structure Simulator (HFSS).

  4. Neutrino Factory: status and prospects

    International Nuclear Information System (INIS)

    Long, K.

    2011-01-01

    The properties of the neutrino provide a unique window on physics beyond that described by the Standard Model. The study of sub-leading effects in neutrino oscillations has begun with the race to measure θ 13 consensus is emerging within the international community that a novel neutrino source is required to allow sensitive searches for leptonic CP violation to be carried out and the neutrino mass-hierarchy to be determined. The Neutrino Factory, in which intense neutrino beams are produced from the decay of muons, has been shown to out-perform the other proposed facilities. The physics case for the Neutrino Factory will be reviewed and the baseline design of the facility being developed by the International Design Study for the Neutrino Factory (the IDS-NF) collaboration will be described.

  5. Steps towards the Neutrino Factory

    International Nuclear Information System (INIS)

    Long, K.

    2012-01-01

    The properties of the neutrino provide a unique window on physics beyond that described by the Standard Model. The study of sub-leading effects in neutrino oscillations has begun with the race to measure θ 13 . A consensus is emerging within the international community that a novel neutrino source is required to allow sensitive searches for leptonic CP violation to be carried out and the neutrino mass-hierarchy to be determined. The Neutrino Factory, in which intense neutrino beams are produced from the decay of muons, has been shown to out-perform the other proposed facilities. The physics case for the Neutrino Factory will be reviewed and the baseline design of the facility being developed by the International Design Study for the Neutrino Factory (the IDS-NF) collaboration will be described.

  6. Designing simulation experiments with controllable and uncontrollable factors for applications in healthcare

    DEFF Research Database (Denmark)

    Dehlendorff, Christian; Kulahci, Murat; Andersen, Klaus Kaae

    2011-01-01

    We propose a new methodology for designing computer experiments that was inspired by the split-plot designs that are often used in physical experimentation.The methodology has been developed for a simulation model of a surgical unit in a Danish hospital.We classify the factors as controllable and...

  7. Relative Efficiency of Split-plot Design (SPD) to Randomized ...

    African Journals Online (AJOL)

    West African Journal of Industrial and Academic Research. Journal Home · ABOUT THIS JOURNAL · Advanced Search · Current Issue · Archives · Journal Home > Vol 7, No 1 (2013) >. Log in or Register to get access to full text downloads.

  8. Coded Splitting Tree Protocols

    DEFF Research Database (Denmark)

    Sørensen, Jesper Hemming; Stefanovic, Cedomir; Popovski, Petar

    2013-01-01

    This paper presents a novel approach to multiple access control called coded splitting tree protocol. The approach builds on the known tree splitting protocols, code structure and successive interference cancellation (SIC). Several instances of the tree splitting protocol are initiated, each...... instance is terminated prematurely and subsequently iterated. The combined set of leaves from all the tree instances can then be viewed as a graph code, which is decodable using belief propagation. The main design problem is determining the order of splitting, which enables successful decoding as early...

  9. Isodose plotting for pen plotters

    International Nuclear Information System (INIS)

    Rosen, I.I.

    1985-01-01

    A general algorithm for treatment plan isodose line plotting is described which is particularly useful for pen plotters. Unlike other methods of plotting isodose lines, this algorithm is designed specifically to reduce pen motion, thereby reducing plotting time and wear on the transport mechanism. Points with the desired dose value are extracted from the dose matrix and stored, sorted into continuous contours, and then plotted. This algorithm has been implemented on DEC PDP-11/60 and VAX-11/780 computers for use with two models of Houston Instrument pen plotters, two models of Tektronix vector graphics terminals, a DEC VT125 raster graphics terminal, and a DEC VS11 color raster graphics terminal. Its execution time is similar to simpler direct-plotting methods

  10. System for histogram entry, retrieval, and plotting

    International Nuclear Information System (INIS)

    Kellogg, M.; Gallup, J.M.; Shlaer, S.; Spencer, N.

    1977-10-01

    This manual describes the systems for producing histograms and dot plots that were designed for use in connection with the Q general-purpose data-acquisition system. These systems allow for the creation of histograms; the entry, retrieval, and plotting of data in the form of histograms; and the dynamic display of scatter plots as data are acquired. Although the systems are designed for use with Q, they can also be used as a part of other applications. 3 figures

  11. BliP PLOT : PLOT DISTRIBUSI DATA BERDIMENSI - SATU

    OpenAIRE

    Anisa Anisa; Indwiati Indwiati

    2014-01-01

    Blip Plot, adalah salah satu plot yang sibuat untuk menampilkan data berdimensi-satu. Pada dasarnya plot ini terdiri dari kotak, garis, dan titik. Sebagaimana plot distribusi berdimensi-satu yang lain, BliP Plot menampilkan nilai-nilai data individu dalam titik-titik atau garis-garis, dan informasi berkelompok dalam garis atau kotak. Kelebihannya, Blip Plot menampilkan banyak keistimewaan baru seperti plot variable-widht dan beberapa pilihan pola titik. Keuntungan utama dari Blip ...

  12. Design of a holographic micro-scale spectrum-splitting photovoltaic system

    Science.gov (United States)

    Wu, Yuechen; Vorndran, Shelby; Ayala Pelaez, Silvana; Russo, Juan M.; Kostuk, Raymond K.

    2015-09-01

    Micro-scale PV technology combines the high conversion efficiency of concentrated photovoltaics (CPV) with the low costs and the simple form of flat panel PV. Some of the benefits of micro-scale PV include: reduced semiconductor material usage; improved heat rejection capacity; and more versatile PV cell interconnect configurations. Spectrumsplitting is also a beneficial technique to increase the efficiency and reduce the cost of photovoltaic systems. It spatially separates the incident solar spectrum into spectral components and directs them to PV cells with matching bandgaps. This approach avoids the current and lattice matching problems that exist in tandem multi-junction systems. In this paper, we applied the ideas of spectrum-splitting in a micro-scale PV system, and demonstrated a holographic micro-scale spectrum-splitting photovoltaic system. This system consists of a volume transmission hologram in combination with a micro-lens array. An analysis methodology was developed to design the system and determine the performance of the resulting system. The spatial characteristics of the dispersed spectrum, the overall system conversion efficiency, and the improvement over best bandgap will be discussed.

  13. Muon colliders and neutrino factories

    Energy Technology Data Exchange (ETDEWEB)

    Geer, S.; /Fermilab

    2010-09-01

    Over the last decade there has been significant progress in developing the concepts and technologies needed to produce, capture and accelerate {Omicron}(10{sup 21}) muons/year. This development prepares the way for a new type of neutrino source (Neutrino Factory) and a new type of very high energy lepton-antilepton collider (Muon Collider). This article reviews the motivation, design and R&D for Neutrino Factories and Muon Colliders.

  14. Design Studies for a 1036 SuperB-Factory

    International Nuclear Information System (INIS)

    Seeman, J

    2003-01-01

    A Super B Factory, an asymmetric e + e - collider with a luminosity of 10 36 cm -2 s -1 , can provide a sensitive probe of new physics in the flavor sector of the Standard Model. The success of PEP-II and KEKB in producing unprecedented luminosity with unprecedented short commissioning time has taught us about the accelerator physics of asymmetric e + e - colliders in a new parameter regime. It appears to be possible to build on this success to advance the state of the accelerator art by building a collider at a luminosity approaching 10 36 cm -2 s -1 . Such a collider would produce an integrated luminosity of 10,000 fb -1 (10 ab -1 ) in a running year. Design studies are underway to arrive at a complete parameter set based on a collider in the PEP-II tunnel but with an upgraded RF system (perhaps a higher frequency) and an upgraded interaction region [1-6

  15. Model-based design of bistable cell factories for metabolic engineering.

    Science.gov (United States)

    Srinivasan, Shyam; Cluett, William R; Mahadevan, Radhakrishnan

    2018-04-15

    Metabolism can exhibit dynamic phenomena like bistability due to the presence of regulatory motifs like the positive feedback loop. As cell factories, microorganisms with bistable metabolism can have a high and a low product flux at the two stable steady states, respectively. The exclusion of metabolic regulation and network dynamics limits the ability of pseudo-steady state stoichiometric models to detect the presence of bistability, and reliably assess the outcomes of design perturbations to metabolic networks. Using kinetic models of metabolism, we assess the change in the bistable characteristics of the network, and suggest designs based on perturbations to the positive feedback loop to enable the network to produce at its theoretical maximum rate. We show that the most optimal production design in parameter space, for a small bistable metabolic network, may exist at the boundary of the bistable region separating it from the monostable region of low product fluxes. The results of our analysis can be broadly applied to other bistable metabolic networks with similar positive feedback network topologies. This can complement existing model-based design strategies by providing a smaller number of feasible designs that need to be tested in vivo. http://lmse.biozone.utoronto.ca/downloads/. krishna.mahadevan@utoronto.ca. Supplementary data are available at Bioinformatics online.

  16. Enabling optimization in LCA: from “ad hoc” to “structural” LCA approach—based on a biodiesel well-to-wheel case study

    DEFF Research Database (Denmark)

    Herrmann, Ivan Tengbjerg; Lundberg-Jensen, Martin; Jørgensen, Andreas

    2014-01-01

    for searching or screening product systems for environmental optimization potentials. In the presented case, the design has been a rather simple full factorial design. More complicated problems or designs, such as fractional designs, nested designs, split plot designs, and/or unbalanced data, in the context...... 2005). Through a biodiesel well-to-wheel study, we demonstrate a generic approach of applying explanatory variables and corresponding impact categories within the LCA methodology. Explanatory variables are product system variables that can influence the environmental impacts from the system....... Furthermore, using the structural approach enables two different possibilities for optimization: (1) single-objective optimization (SO) based on response surface methodology (Montgomery 2005) and (2) multiobjective optimization (MO) by the hypervolume estimation taboo search (HETS) method. HETS enables MO...

  17. An improved ultra-wideband bandpass filter design using split ring resonator with coupled microstrip line

    Science.gov (United States)

    Umeshkumar, Dubey Suhmita; Kumar, Manish

    2018-04-01

    This paper incorporates an improved design of Ultra Wideband Bandpass filter by using split ring resonators (SRR) along with the coupled microstrip lines. The use of split ring resonators and shunt step impedance open circuit stub enhances the stability due to transmission zeroes at the ends. The designing of filter and simulation of parameters is carried out using Ansoft's HFSS 13.0 software on RT/Duroid 6002 as a substrate with dielectric constant of 2.94. The design utilizes a frequency band from 22GHz to 29GHz. This band is reserved for Automotive Radar system and sensors as per FCC specifications. The proposed design demonstrates insertion loss less than 0.6dB and return loss better than 12dB at mid frequency i.e. 24.4GHz. The reflection coefficient shows high stability of about 12.47dB at mid frequency. The fractional bandwidth of the proposed filter is about 28.7% and size of filter design is small due to thickness of 0.127mm.

  18. Preconceptual design of a salt splitting process using ceramic membranes

    Energy Technology Data Exchange (ETDEWEB)

    Kurath, D.E.; Brooks, K.P.; Hollenberg, G.W.; Clemmer, R. [Pacific Northwest National Lab., Richland, WA (United States); Balagopal, S.; Landro, T.; Sutija, D.P. [Ceramatec, Inc., Salt Lake City, UT (United States)

    1997-01-01

    Inorganic ceramic membranes for salt splitting of radioactively contaminated sodium salt solutions are being developed for treating U. S. Department of Energy tank wastes. The process consists of electrochemical separation of sodium ions from the salt solution using sodium (Na) Super Ion Conductors (NaSICON) membranes. The primary NaSICON compositions being investigated are based on rare- earth ions (RE-NaSICON). Potential applications include: caustic recycling for sludge leaching, regenerating ion exchange resins, inhibiting corrosion in carbon-steel tanks, or retrieving tank wastes; reducing the volume of low-level wastes volume to be disposed of; adjusting pH and reducing competing cations to enhance cesium ion exchange processes; reducing sodium in high-level-waste sludges; and removing sodium from acidic wastes to facilitate calcining. These applications encompass wastes stored at the Hanford, Savannah River, and Idaho National Engineering Laboratory sites. The overall project objective is to supply a salt splitting process unit that impacts the waste treatment and disposal flowsheets and meets user requirements. The potential flowsheet impacts include improving the efficiency of the waste pretreatment processes, reducing volume, and increasing the quality of the final waste disposal forms. Meeting user requirements implies developing the technology to the point where it is available as standard equipment with predictable and reliable performance. This report presents two preconceptual designs for a full-scale salt splitting process based on the RE-NaSICON membranes to distinguish critical items for testing and to provide a vision that site users can evaluate.

  19. Preconceptual design of a salt splitting process using ceramic membranes

    International Nuclear Information System (INIS)

    Kurath, D.E.; Brooks, K.P.; Hollenberg, G.W.; Clemmer, R.; Balagopal, S.; Landro, T.; Sutija, D.P.

    1997-01-01

    Inorganic ceramic membranes for salt splitting of radioactively contaminated sodium salt solutions are being developed for treating U. S. Department of Energy tank wastes. The process consists of electrochemical separation of sodium ions from the salt solution using sodium (Na) Super Ion Conductors (NaSICON) membranes. The primary NaSICON compositions being investigated are based on rare- earth ions (RE-NaSICON). Potential applications include: caustic recycling for sludge leaching, regenerating ion exchange resins, inhibiting corrosion in carbon-steel tanks, or retrieving tank wastes; reducing the volume of low-level wastes volume to be disposed of; adjusting pH and reducing competing cations to enhance cesium ion exchange processes; reducing sodium in high-level-waste sludges; and removing sodium from acidic wastes to facilitate calcining. These applications encompass wastes stored at the Hanford, Savannah River, and Idaho National Engineering Laboratory sites. The overall project objective is to supply a salt splitting process unit that impacts the waste treatment and disposal flowsheets and meets user requirements. The potential flowsheet impacts include improving the efficiency of the waste pretreatment processes, reducing volume, and increasing the quality of the final waste disposal forms. Meeting user requirements implies developing the technology to the point where it is available as standard equipment with predictable and reliable performance. This report presents two preconceptual designs for a full-scale salt splitting process based on the RE-NaSICON membranes to distinguish critical items for testing and to provide a vision that site users can evaluate

  20. B-factory detectors

    International Nuclear Information System (INIS)

    Marlow, D.R.

    2002-01-01

    The designs of the recently commissioned BaBar and Belle B-Factory detectors are described. The discussion is organized around the methods and instruments used to detect the so-called gold-plated-mode B 0 →J/ΨK S decays and related modes

  1. Phenomenology of neutrino oscillations at the neutrino factory

    International Nuclear Information System (INIS)

    Tang, Jian

    2011-01-01

    We consider the prospects for a neutrino factory measuring mixing angles, the CP violating phase and mass-squared differences by detecting wrong-charge muons arising from the chain μ + → ν e → ν μ → μ - and the right-charge muons coming from the chain μ + → anti ν μ → anti ν μ → μ - (similar to μ - chains), where ν e → ν μ and anti ν μ → anti ν μ are neutrino oscillation channels through a long baseline. First, we study physics with near detectors and consider the treatment of systematic errors including cross section errors, flux errors, and background uncertainties. We illustrate for which measurements near detectors are required, discuss how many are needed, and what the role of the flux monitoring is. We demonstrate that near detectors are mandatory for the leading atmospheric parameter measurements if the neutrino factory has only one baseline, whereas systematic errors partially cancel if the neutrino factory complex includes the magic baseline. Second, we perform the baseline and energy optimization of the neutrino factory including the latest simulation results from the magnetized iron neutrino detector (MIND). We also consider the impact of τ decays, generated by appearance channels ν μ → ν τ and ν e → ν τ , on the discovery reaches of the mass orderings, the leptonic CP violation, and the non-zero θ 13 , which we find to be negligible for the considered detector. Third, we make a comparison of a high energy neutrino factory to a low energy neutrino factory and find that they are just two versions of the same experiment optimized for different regions of the parameter space. In addition, we briefly comment on whether it is useful to build the bi-magic baseline at the low energy neutrino factory. Finally, the effects of one additional massive sterile neutrino are discussed in the context of a combined short and long baseline setup. It is found that near detectors can provide the required sensitivity at the

  2. Predicting guar seed splitting by compression between two plates using Hertz theory of contact stresses.

    Science.gov (United States)

    Vishwakarma, R K; Shivhare, U S; Nanda, S K

    2012-09-01

    Hertz's theory of contact stresses was applied to predict the splitting of guar seeds during uni-axial compressive loading between 2 rigid parallel plates. The apparent modulus of elasticity of guar seeds varied between 296.18 and 116.19 MPa when force was applied normal to hilum joint (horizontal position), whereas it varied between 171.86 and 54.18 MPa when force was applied in the direction of hilum joint (vertical position) with in moisture content range of 5.16% to 15.28% (d.b.). At higher moisture contents, the seeds yielded after considerable deformation, thus showing ductile nature. Distribution of stresses below the point of contact were plotted to predict the location of critical point, which was found at 0.44 to 0.64 mm and 0.37 to 0.53 mm below the contact point in vertical and horizontal loading, respectively, depending upon moisture content. The separation of cotyledons from each other initiated before yielding of cotyledons and thus splitting of seed took place. The relationships between apparent modulus of elasticity, principal stresses with moisture content were described using second-order polynomial equations and validated experimentally. Manufacture of guar gum powder requires dehulling and splitting of guar seeds. This article describes splitting behavior of guar seeds under compressive loading. Results of this study may be used for design of dehulling and splitting systems of guar seeds. © 2012 Institute of Food Technologists®

  3. Development and application of computer-aided design methods for cell factory optimization

    DEFF Research Database (Denmark)

    Cardoso, Joao

    Genetically modified organisms (GMOs) can be used to produce chemicals for everyday applications. Engineering microorganisms is a multidisciplinary task comprising four steps: design, build, test and learn. The design and learn phases rely on computational, statistical models, data analysis...... and machine learning. The process of creating strains with commercially relevant titers is time consuming and expensive. Computer-aided design (CAD) software can help scientists build better strains by providing models and algorithms that can be used to generate and test hypotheses before implementing them...... microbial cell factories. In this PhD thesis we present cameo, a CAD software for metabolic engineering that uses GEMs. State-of-the-art and novel algorithms are implemented in cameo. These algorithms have been made accessible using a high-level API to enable any user to start running them without having...

  4. PEP-II: An asymmetric B factory. Conceptual design report

    Energy Technology Data Exchange (ETDEWEB)

    1993-06-01

    In this report, the authors have described an updated conceptual design for the high-luminosity Asymmetric B Factory (PEP-II) to be built in the PEP tunnel culmination of more than four years of effort aimed at the design and construction of an asymmetric e{sub +}e{sub {minus}} collider capable of achieving a luminosity of L = 3 {times} 10{sup 33} cm{sup {minus}2} s{sup {minus}1}. All aspects of the conceptual design were scrutinized in March 1991 by a DOE technical review committee chaired by Dr. L. Edward Temple. The design was deemed feasible and capable of achieving its physics goals. Furthermore, the cost estimate, schedule, and management plan for the project were fully endorsed by the committee. This updated conceptual design report captures the technical progress since the March 1991 review and reflects the lower cost estimate corresponding to the improved design. Although the PEP-II design has continued to evolve, no technical scope changes have been made that invalidate the conclusion of the DOE review. The configuration adopted utilizes two storage rings, an electron ring operating at 9 GeV and a positron ring at 3.1 GeV, each with a circumference of 2200 m. The high-energy ring is an upgrade of the PEP storage ring at SLAC; all PEP magnets and most power supplies will be reused. The upgrade consists primarily of replacing the PEP vacuum chamber and RF system with newly designed versions optimized for the high-current environment of PEP-II. The low-energy ring will be newly constructed and will be situated atop the high-energy ring in the PEP tunnel. Utilities already installed in the PEP tunnel are largely sufficient to operate the two PEP-II storage rings.

  5. A Prospectus on Restoring Late Successional Forest Structure to Eastside Pine Ecosystems Through Large-Scale, Interdisciplinary Research

    Science.gov (United States)

    Steve Zack; William F. Laudenslayer; Luke George; Carl Skinner; William Oliver

    1999-01-01

    At two different locations in northeast California, an interdisciplinary team of scientists is initiating long-term studies to quantify the effects of forest manipulations intended to accelerate andlor enhance late-successional structure of eastside pine forest ecosystems. One study, at Blacks Mountain Experimental Forest, uses a split-plot, factorial, randomized block...

  6. Optimal covariate designs theory and applications

    CERN Document Server

    Das, Premadhis; Mandal, Nripes Kumar; Sinha, Bikas Kumar

    2015-01-01

    This book primarily addresses the optimality aspects of covariate designs. A covariate model is a combination of ANOVA and regression models. Optimal estimation of the parameters of the model using a suitable choice of designs is of great importance; as such choices allow experimenters to extract maximum information for the unknown model parameters. The main emphasis of this monograph is to start with an assumed covariate model in combination with some standard ANOVA set-ups such as CRD, RBD, BIBD, GDD, BTIBD, BPEBD, cross-over, multi-factor, split-plot and strip-plot designs, treatment control designs, etc. and discuss the nature and availability of optimal covariate designs. In some situations, optimal estimations of both ANOVA and the regression parameters are provided. Global optimality and D-optimality criteria are mainly used in selecting the design. The standard optimality results of both discrete and continuous set-ups have been adapted, and several novel combinatorial techniques have been applied for...

  7. Interpretation of custom designed Illumina genotype cluster plots for targeted association studies and next-generation sequence validation

    Directory of Open Access Journals (Sweden)

    Tindall Elizabeth A

    2010-02-01

    Full Text Available Abstract Background High-throughput custom designed genotyping arrays are a valuable resource for biologically focused research studies and increasingly for validation of variation predicted by next-generation sequencing (NGS technologies. We investigate the Illumina GoldenGate chemistry using custom designed VeraCode and sentrix array matrix (SAM assays for each of these applications, respectively. We highlight applications for interpretation of Illumina generated genotype cluster plots to maximise data inclusion and reduce genotyping errors. Findings We illustrate the dramatic effect of outliers in genotype calling and data interpretation, as well as suggest simple means to avoid genotyping errors. Furthermore we present this platform as a successful method for two-cluster rare or non-autosomal variant calling. The success of high-throughput technologies to accurately call rare variants will become an essential feature for future association studies. Finally, we highlight additional advantages of the Illumina GoldenGate chemistry in generating unusually segregated cluster plots that identify potential NGS generated sequencing error resulting from minimal coverage. Conclusions We demonstrate the importance of visually inspecting genotype cluster plots generated by the Illumina software and issue warnings regarding commonly accepted quality control parameters. In addition to suggesting applications to minimise data exclusion, we propose that the Illumina cluster plots may be helpful in identifying potential in-put sequence errors, particularly important for studies to validate NGS generated variation.

  8. Virtual Learning Factory on VR-Supported Factory Planning

    OpenAIRE

    Weidig , Christian; Menck , Nicole; Winkes , Pascal ,; Aurich , Jan ,

    2014-01-01

    Part 13: Virtual Reality and Simulation; International audience; Learning Factories are becoming popular as tangible measures to teach engineering methods while making use of them in an industrial-like environment. Their core component is usually a factory demonstrator, users are physically working with. For factory planning such approaches can hardly be adapted, due to long lasting realization phases.To overcome this obstacle a virtual learning factory has been developed whose core component...

  9. MODEL PENGELOLAAN TEACHING FACTORY SEKOLAH MENENGAH KEJURUAN

    Directory of Open Access Journals (Sweden)

    M Burhan R Wijaya

    2013-02-01

    Full Text Available This study aims to identify and develop management models Factory Teaching Vocational School through a series of tests and validation of the model with the approach of reasearch and Development. Teaching Factory Management Models at Vocational Schools is a concept that combines learning management approach learning Competency Based Training (CBT and Production Based Training (PBT in the real atmosphere so that the process of achieving competence or skill skills life skills (life skills in accordance with the standards of graduate work in the industrial world. In particular, this study aims to formulate design management model development Teaching Factory Vocational School. To achieve the research objectives above using the approach of Research and Development, through preliminary studies, design development models, testing and validation. Preliminary study phase is planned to take the flow / stage as follows: the study of literature, study / collection of field data, and a description and analysis of field findings (factual, namely: (1 the description of the characteristics of vocational school with a standard performance indicators that can be poured as the content of the development of Teaching Factory, (2 description of the characteristics and potential development group management model Tefa as an outcome groups to develop and implement management models Tefa for Vocational Schools (3 description of the characteristics of potential stakeholders to support the development and implementation TEFA management model, and (4 preparation of the management model TEFA for Vocational Schools excellence and innovative. Trial design done on a limited scale model group. Then the model was accompanied by outcome group to develop and implement a model TEFA for Vocational Schools to determine whether the model developed can be applied correctly. Data analysis in this study, the preliminary study stage, the findings or the facts about productive learning

  10. Lighting up yeast cell factories by transcription factor-based biosensors

    DEFF Research Database (Denmark)

    D'ambrosio, Vasil; Jensen, Michael Krogh

    2017-01-01

    Our ability to rewire cellular metabolism for the sustainable production of chemicals, fuels and therapeutics based on microbial cell factories has advanced rapidly during the last two decades. Especially the speed and precision by which microbial genomes can be engineered now allow for more...... process. For this purpose, there is a need to develop new techniques for screening and selection of best-performing cell factory designs in multiplex. Here we review the current status of the sourcing, design and engineering of biosensors derived from allosterically regulated transcription factors applied...... advanced designs to be implemented and tested. However, compared to the methods developed for engineering cell factories, the methods developed for testing the performance of newly engineered cell factories in high throughput are lagging far behind, which consequently impacts the overall biomanufacturing...

  11. Review of U.S. Neutrino Factory Studies

    International Nuclear Information System (INIS)

    Zisman, Michael S.

    2005-01-01

    We summarize the status of the two U.S. feasibility studies carried out by the Neutrino Factory and Muon Collider Collaboration (NFMCC) along with recent improvements to Neutrino Factory design developed during the American Physical Society (APS) Neutrino Physics Study. Suggested accelerator topics for the International Scoping Study (ISS) are also indicated

  12. SCREENING OF MEDIUM COMPOUNDS USING A TWO-LEVEL FACTORIAL DESIGN FOR SACCHAROMYCES BOULARDII

    Directory of Open Access Journals (Sweden)

    GUOWEI SHU

    2016-04-01

    Full Text Available Even if the probiotic effect of Saccharomyces boulardii is has been reported, this yeast is rarely used in medium composition. Based on single factor experiment, two-level factorial design was employed to evaluate the effect of carbon sources (sucrose, glucose, nitrogen sources (soy peptone, beef extract, yeast extract, calf serum, malt extract and salts (K2HPO4, KH2PO4, MgSO4, Na2HPO4, NaH2PO4, CaCl2, sodium citrate, sodium glutamate on the growth of S. boulardii. At the same time, the optical density (OD in the medium was measured at 560 nm after 36 h of incubation. The result of two-level factorial design experiment showed that calf serum (p = 0.0214 and sodium citrate (p = 0.0045 are the significant growth factors of S. boulardii, sucrose (p = 0.0861 and malt extract (p = 0.0763 are important factors. In addition, sucrose and sodium citrate showed positive effect on the growth of S. boulardii. However, calf serum and malt extract showed negative effect on the growth. And we determined that the optimum medium composition for S. boulardii was as follow: 37.5 g·L-1 sucrose, 6 g·L-1 calf serum, 6 g·L-1 malt extract, 5 g·L-1 sodium citrate.

  13. The TRIUMF KAON Factory

    International Nuclear Information System (INIS)

    Craddock, M.

    1989-05-01

    TRIUMF has been awarded $11M for a one-year pre-construction Engineering Design and Impact Study of the KAON Factory. This will enable prototypes of many accelerator components to be built and the design of the accelerators and the layout of the experimental areas to be reviewed. The building and tunnel designs will be finalized, environmental, legal and economic impact studies carried out, and international involvement pursued further

  14. INDOOR THERMAL CONDITION OF FACTORY BUILDING IN BANGLADESH

    OpenAIRE

    Muhammed Abdullah Al Sayem Khan; Mohd. Hamdan Ahmad; Tareef Hayat Khan

    2011-01-01

    Bangladesh is a developing country and has a lot of factories for different products for local use and also export to abroad. Garments industries are one of the top most items of exported items. A huge number of populations are working in garments industries. But these factories are not well designed in sense of the thermal environment. Workers experiences sickness related to indoor environment. The productions of these factories are affected due to employees’ health condition. The research i...

  15. Considerations in Forest Growth Estimation Between Two Measurements of Mapped Forest Inventory Plots

    Science.gov (United States)

    Michael T. Thompson

    2006-01-01

    Several aspects of the enhanced Forest Inventory and Analysis (FIA) program?s national plot design complicate change estimation. The design incorporates up to three separate plot sizes (microplot, subplot, and macroplot) to sample trees of different sizes. Because multiple plot sizes are involved, change estimators designed for polyareal plot sampling, such as those...

  16. DESIGN AND LAYOUT CONCEPTS FOR COMPACT, FACTORY-PRODUCED, TRANSPORTABLE, GENERATION IV REACTOR SYSTEMS

    Energy Technology Data Exchange (ETDEWEB)

    Mynatt Fred R.; Townsend, L.W.; Williamson, Martin; Williams, Wesley; Miller, Laurence W.; Khan, M. Khurram; McConn, Joe; Kadak, Andrew C.; Berte, Marc V.; Sawhney, Rapinder; Fife, Jacob; Sedler, Todd L.; Conway, Larry E.; Felde, Dave K.

    2003-11-12

    The purpose of this research project is to develop compact (100 to 400 MWe) Generation IV nuclear power plant design and layout concepts that maximize the benefits of factory-based fabrication and optimal packaging, transportation and siting. The reactor concepts selected were compact designs under development in the 2000 to 2001 period. This interdisciplinary project was comprised of three university-led nuclear engineering teams identified by reactor coolant type (water, gas, and liquid metal) and a fourth Industrial Engineering team. The reactors included a Modular Pebble Bed helium-cooled concept being developed at MIT, the IRIS water-cooled concept being developed by a team led by Westinghouse Electric Company, and a Lead-Bismuth-cooled concept developed by UT. In addition to the design and layout concepts this report includes a section on heat exchanger manufacturing simulations and a section on construction and cost impacts of proposed modular designs.

  17. DESIGN AND LAYOUT CONCEPTS FOR COMPACT, FACTORY-PRODUCED, TRANSPORTABLE, GENERATION IV REACTOR SYSTEMS

    International Nuclear Information System (INIS)

    Mynatt, Fred R.; Townsend, L.W.; Williamson, Martin; Williams, Wesley; Miller, Laurence W.; Khan, M. Khurram; McConn, Joe; Kadak, Andrew C.; Berte, Marc V.; Sawhney, Rapinder; Fife, Jacob; Sedler, Todd L.; Conway, Larry E.; Felde, Dave K.

    2003-01-01

    The purpose of this research project is to develop compact (100 to 400 MWe) Generation IV nuclear power plant design and layout concepts that maximize the benefits of factory-based fabrication and optimal packaging, transportation and siting. The reactor concepts selected were compact designs under development in the 2000 to 2001 period. This interdisciplinary project was comprised of three university-led nuclear engineering teams identified by reactor coolant type (water, gas, and liquid metal) and a fourth Industrial Engineering team. The reactors included a Modular Pebble Bed helium-cooled concept being developed at MIT, the IRIS water-cooled concept being developed by a team led by Westinghouse Electric Company, and a Lead-Bismuth-cooled concept developed by UT. In addition to the design and layout concepts this report includes a section on heat exchanger manufacturing simulations and a section on construction and cost impacts of proposed modular designs

  18. Optimization of LDL targeted nanostructured lipid carriers of 5-FU by a full factorial design.

    Science.gov (United States)

    Andalib, Sare; Varshosaz, Jaleh; Hassanzadeh, Farshid; Sadeghi, Hojjat

    2012-01-01

    Nanostructured lipid carriers (NLC) are a mixture of solid and liquid lipids or oils as colloidal carrier systems that lead to an imperfect matrix structure with high ability for loading water soluble drugs. The aim of this study was to find the best proportion of liquid and solid lipids of different types for optimization of the production of LDL targeted NLCs used in carrying 5-Fu by the emulsification-solvent evaporation method. The influence of the lipid type, cholesterol or cholesteryl stearate for targeting LDL receptors, oil type (oleic acid or octanol), lipid and oil% on particle size, surface charge, drug loading efficiency, and drug released percent from the NLCs were studied by a full factorial design. The NLCs prepared by 54.5% cholesterol and 25% of oleic acid, showed optimum results with particle size of 105.8 nm, relatively high zeta potential of -25 mV, drug loading efficiency of 38% and release efficiency of about 40%. Scanning electron microscopy of nanoparticles confirmed the results of dynamic light scattering method used in measuring the particle size of NLCs. The optimization method by a full factorial statistical design is a useful optimization method for production of nanostructured lipid carriers.

  19. Phenomenology of neutrino oscillations at the neutrino factory

    Energy Technology Data Exchange (ETDEWEB)

    Tang, Jian

    2011-12-19

    We consider the prospects for a neutrino factory measuring mixing angles, the CP violating phase and mass-squared differences by detecting wrong-charge muons arising from the chain {mu}{sup +} {yields} {nu}{sub e} {yields} {nu}{sub {mu}} {yields} {mu}{sup -} and the right-charge muons coming from the chain {mu}{sup +} {yields} anti {nu}{sub {mu}} {yields} anti {nu}{sub {mu}} {yields} {mu}{sup -} (similar to {mu}{sup -} chains), where {nu}{sub e} {yields} {nu}{sub {mu}} and anti {nu}{sub {mu}} {yields} anti {nu}{sub {mu}} are neutrino oscillation channels through a long baseline. First, we study physics with near detectors and consider the treatment of systematic errors including cross section errors, flux errors, and background uncertainties. We illustrate for which measurements near detectors are required, discuss how many are needed, and what the role of the flux monitoring is. We demonstrate that near detectors are mandatory for the leading atmospheric parameter measurements if the neutrino factory has only one baseline, whereas systematic errors partially cancel if the neutrino factory complex includes the magic baseline. Second, we perform the baseline and energy optimization of the neutrino factory including the latest simulation results from the magnetized iron neutrino detector (MIND). We also consider the impact of {tau} decays, generated by appearance channels {nu}{sub {mu}} {yields} {nu}{sub {tau}} and {nu}{sub e} {yields} {nu}{sub {tau}}, on the discovery reaches of the mass orderings, the leptonic CP violation, and the non-zero {theta}{sub 13}, which we find to be negligible for the considered detector. Third, we make a comparison of a high energy neutrino factory to a low energy neutrino factory and find that they are just two versions of the same experiment optimized for different regions of the parameter space. In addition, we briefly comment on whether it is useful to build the bi-magic baseline at the low energy neutrino factory. Finally, the

  20. Planned e+e- factories

    International Nuclear Information System (INIS)

    Le Duff, J.

    1993-09-01

    Various Beauty and Tau-Charm factories and projects are reviewed. Different machines (TRISTAN II, PEP II, CESR-B, the Dubna project and the European project) are compared and their design and parameters are described. (K.A.) 34 refs., 2 figs., 2 tabs

  1. Design and optimization of cascaded DCG based holographic elements for spectrum-splitting PV systems

    Science.gov (United States)

    Wu, Yuechen; Chrysler, Benjamin; Pelaez, Silvana Ayala; Kostuk, Raymond K.

    2017-09-01

    In this work, the technique of designing and optimizing broadband volume transmission holograms using dichromate gelatin (DCG) is summarized for solar spectrum-splitting application. Spectrum splitting photovoltaic system uses a series of single bandgap PV cells that have different spectral conversion efficiency properties to more fully utilize the solar spectrum. In such a system, one or more high performance optical filters are usually required to split the solar spectrum and efficiently send them to the corresponding PV cells. An ideal spectral filter should have a rectangular shape with sharp transition wavelengths. DCG is a near ideal holographic material for solar applications as it can achieve high refractive index modulation, low absorption and scattering properties and long-term stability to solar exposure after sealing. In this research, a methodology of designing and modeling a transmission DCG hologram using coupled wave analysis for different PV bandgap combinations is described. To achieve a broad diffraction bandwidth and sharp cut-off wavelength, a cascaded structure of multiple thick holograms is described. A search algorithm is also developed to optimize both single and two-layer cascaded holographic spectrum splitters for the best bandgap combinations of two- and three-junction SSPV systems illuminated under the AM1.5 solar spectrum. The power conversion efficiencies of the optimized systems under the AM1.5 solar spectrum are then calculated using the detailed balance method, and shows an improvement compared with tandem structure.

  2. The Three-dimensional Digital Factory for Shipbuilding Technology Research

    Directory of Open Access Journals (Sweden)

    Xu Wei

    2016-01-01

    Full Text Available The three-dimensional digital factory technology research is the hotspot in shipbuilding recently. The three-dimensional digital factory technology not only focus on design the components of the product, but also discuss on the simulation and analyses of the production process.Based on the three-dimensional model, the basic data layer, application control layer and the presentation layer of hierarchical structure are established in the three-dimensional digital factory of shipbuilding in this paper. And the key technologies of three-dimensional digital factory of shipbuilding are analysed. Finally, a case study is applied and the results show that the three-dimensional digital factory will play an important role in the future.

  3. Design, manufacture and factory testing of the Ion Source and Extraction Power Supplies for the SPIDER experiment

    International Nuclear Information System (INIS)

    Bigi, Marco; Rinaldi, Luigi; Simon, Muriel; Sita, Luca; Taddia, Giuseppe; Carrozza, Saverino; Decamps, Hans; Luchetta, Adriano; Meddour, Abdelraouf; Moressa, Modesto; Morri, Cristiano; Musile Tanzi, Antonio; Recchia, Mauro; Wagner, Uwe; Zamengo, Andrea; Toigo, Vanni

    2015-01-01

    Highlights: • 5 MVA ion source power supplies effectively integrated in 150 m"2 Faraday cage. • Load protection and performance requirements met of custom design high voltage power supplies. • 200 kW tetrode oscillator with 200 kHz frequency range successfully tested. - Abstract: The SPIDER experiment, currently under construction at the Neutral Beam Test Facility in Padua, Italy, is a full-size prototype of the ion source for the ITER Neutral Beam Injectors. The Ion Source and Extraction Power Supplies (ISEPS) for SPIDER are supplied by OCEM Energy Technology s.r.l. (OCEM) under a procurement contract with Fusion for Energy (F4E) covering also the units required for MITICA and ITER injectors. The detailed design of SPIDER ISEPS was finalized in 2011 and manufacture of most components completed by end 2013. The Factory Acceptance Tests took place early 2014. ISEPS, with an overall power rating of 5 MVA, form a heterogeneous set of items including solid state power converters and 1 MHz radiofrequency generators of 200 kW output power. The paper presents the main features of the detailed design developed by OCEM, focusing in particular on the high output voltage pulse step modulators, the high output current resonant converters, the radiofrequency generators by HIMMELWERK GmbH and the architecture and implementation of the complex control system. Details are given on non-standard factory tests verifying the insulation requirements specific to this application. Performance of ISEPS during the factory acceptance tests is described, with emphasis on demonstration of the load protection requirements, a crucial point for all neutral beam power supplies. Finally, key dates of SPIDER ISEPS installation and site testing schedule are provided.

  4. Design, manufacture and factory testing of the Ion Source and Extraction Power Supplies for the SPIDER experiment

    Energy Technology Data Exchange (ETDEWEB)

    Bigi, Marco, E-mail: marco.bigi@igi.cnr.it [Consorzio RFX (CNR, ENEA, INFN, Università di Padova, Acciaierie Venete SpA), Corso Stati Uniti 4, 35127 Padova (Italy); Rinaldi, Luigi [OCEM Energy Technology, Via della Solidarietà 2/1, 40056 Valsamoggia (località Crespellano), Bologna (Italy); Simon, Muriel [Fusion for Energy, Josep Pla 2, 08019 Barcelona (Spain); Sita, Luca; Taddia, Giuseppe; Carrozza, Saverino [OCEM Energy Technology, Via della Solidarietà 2/1, 40056 Valsamoggia (località Crespellano), Bologna (Italy); Decamps, Hans [ITER Organization, Route de Vinon sur Verdon, 13115 Saint Paul lez Durance (France); Luchetta, Adriano [Consorzio RFX (CNR, ENEA, INFN, Università di Padova, Acciaierie Venete SpA), Corso Stati Uniti 4, 35127 Padova (Italy); Meddour, Abdelraouf [HIMMELWERK Hoch- und Mittelfrequenzanlagen GmbH, Jopestr. 10, 72072 Tübingen (Germany); Moressa, Modesto [Consorzio RFX (CNR, ENEA, INFN, Università di Padova, Acciaierie Venete SpA), Corso Stati Uniti 4, 35127 Padova (Italy); Morri, Cristiano; Musile Tanzi, Antonio [OCEM Energy Technology, Via della Solidarietà 2/1, 40056 Valsamoggia (località Crespellano), Bologna (Italy); Recchia, Mauro [Consorzio RFX (CNR, ENEA, INFN, Università di Padova, Acciaierie Venete SpA), Corso Stati Uniti 4, 35127 Padova (Italy); Wagner, Uwe [HIMMELWERK Hoch- und Mittelfrequenzanlagen GmbH, Jopestr. 10, 72072 Tübingen (Germany); Zamengo, Andrea; Toigo, Vanni [Consorzio RFX (CNR, ENEA, INFN, Università di Padova, Acciaierie Venete SpA), Corso Stati Uniti 4, 35127 Padova (Italy)

    2015-10-15

    Highlights: • 5 MVA ion source power supplies effectively integrated in 150 m{sup 2} Faraday cage. • Load protection and performance requirements met of custom design high voltage power supplies. • 200 kW tetrode oscillator with 200 kHz frequency range successfully tested. - Abstract: The SPIDER experiment, currently under construction at the Neutral Beam Test Facility in Padua, Italy, is a full-size prototype of the ion source for the ITER Neutral Beam Injectors. The Ion Source and Extraction Power Supplies (ISEPS) for SPIDER are supplied by OCEM Energy Technology s.r.l. (OCEM) under a procurement contract with Fusion for Energy (F4E) covering also the units required for MITICA and ITER injectors. The detailed design of SPIDER ISEPS was finalized in 2011 and manufacture of most components completed by end 2013. The Factory Acceptance Tests took place early 2014. ISEPS, with an overall power rating of 5 MVA, form a heterogeneous set of items including solid state power converters and 1 MHz radiofrequency generators of 200 kW output power. The paper presents the main features of the detailed design developed by OCEM, focusing in particular on the high output voltage pulse step modulators, the high output current resonant converters, the radiofrequency generators by HIMMELWERK GmbH and the architecture and implementation of the complex control system. Details are given on non-standard factory tests verifying the insulation requirements specific to this application. Performance of ISEPS during the factory acceptance tests is described, with emphasis on demonstration of the load protection requirements, a crucial point for all neutral beam power supplies. Finally, key dates of SPIDER ISEPS installation and site testing schedule are provided.

  5. An Evaluation of the Use of Statistical Procedures in Soil Science

    Directory of Open Access Journals (Sweden)

    Laene de Fátima Tavares

    2016-01-01

    Full Text Available ABSTRACT Experimental statistical procedures used in almost all scientific papers are fundamental for clearer interpretation of the results of experiments conducted in agrarian sciences. However, incorrect use of these procedures can lead the researcher to incorrect or incomplete conclusions. Therefore, the aim of this study was to evaluate the characteristics of the experiments and quality of the use of statistical procedures in soil science in order to promote better use of statistical procedures. For that purpose, 200 articles, published between 2010 and 2014, involving only experimentation and studies by sampling in the soil areas of fertility, chemistry, physics, biology, use and management were randomly selected. A questionnaire containing 28 questions was used to assess the characteristics of the experiments, the statistical procedures used, and the quality of selection and use of these procedures. Most of the articles evaluated presented data from studies conducted under field conditions and 27 % of all papers involved studies by sampling. Most studies did not mention testing to verify normality and homoscedasticity, and most used the Tukey test for mean comparisons. Among studies with a factorial structure of the treatments, many had ignored this structure, and data were compared assuming the absence of factorial structure, or the decomposition of interaction was performed without showing or mentioning the significance of the interaction. Almost none of the papers that had split-block factorial designs considered the factorial structure, or they considered it as a split-plot design. Among the articles that performed regression analysis, only a few of them tested non-polynomial fit models, and none reported verification of the lack of fit in the regressions. The articles evaluated thus reflected poor generalization and, in some cases, wrong generalization in experimental design and selection of procedures for statistical analysis.

  6. Particle factories

    International Nuclear Information System (INIS)

    Schindler, Rafe

    1989-01-01

    Physicists' attention is increasingly turning to the high luminosity frontier - providing enough collisions to amass sizable numbers of rare events - to complement the traditional quest for higher energies. This month we cover three areas where projects are now being considered: Phi-factory workshop, PSI Planning for B meson factory, Tau-charm factory

  7. Particle factories

    Energy Technology Data Exchange (ETDEWEB)

    Schindler, Rafe

    1989-07-15

    Physicists' attention is increasingly turning to the high luminosity frontier - providing enough collisions to amass sizable numbers of rare events - to complement the traditional quest for higher energies. This month we cover three areas where projects are now being considered: Phi-factory workshop, PSI Planning for B meson factory, Tau-charm factory.

  8. PLOT-3D, Graphics Subroutines for 3-D Surface Plots with Arbitrary Rotations

    International Nuclear Information System (INIS)

    Basinger, D.; Gvildys, J.

    1975-01-01

    1 - Description of problem or function: PLOT-3D is a package of sub- programs designed to draw three-dimensional surfaces from arrays of points (x,y,z). The surfaces can be drawn after arbitrary rotations about the three coordinate axes. 2 - Method of solution: PLOT-3D is a computer program to plot any surface for which each coordinate pair (x,y) is associated with a unique z in the set of points (x,y,z). It uses matrix transformation of the points to generate different views of the surface after arbitrary rotations about the three coordinate axes. Four versions of PLOT-3D are available. Output of version 1 and 3 is by film recorder. Output of version 2 and 4 is by CalComp plotter. Versions 3 and 4 do not draw lines which would be invisible to a viewer looking at an opaque surface, whereas versions 1 and 2 draw every line on the surface. 3 - Restrictions on the complexity of the problem: Versions 3 and 4 limit number of rows in arrays (x,y,z) to 100 and also number of columns in arrays (x,y,z) to 100

  9. Proceedings of the 2-nd workshop on JINR tau-charm factory

    International Nuclear Information System (INIS)

    Aleksandrov, V.S.; Perel'shtejn, E.A.

    1993-01-01

    Application of tau-charm factory for investigation of hadronic decay and charged leptonic weak interaction is considered. JINR tau-charm-factory design and magnetic and vacuum systems of the booster ring are described. New types of silicon microstrip detector sand BGO-counters developed for tau-charm-factory are proposed

  10. Engineering microbial cell factories for the production of plant natural products: from design principles to industrial-scale production.

    Science.gov (United States)

    Liu, Xiaonan; Ding, Wentao; Jiang, Huifeng

    2017-07-19

    Plant natural products (PNPs) are widely used as pharmaceuticals, nutraceuticals, seasonings, pigments, etc., with a huge commercial value on the global market. However, most of these PNPs are still being extracted from plants. A resource-conserving and environment-friendly synthesis route for PNPs that utilizes microbial cell factories has attracted increasing attention since the 1940s. However, at the present only a handful of PNPs are being produced by microbial cell factories at an industrial scale, and there are still many challenges in their large-scale application. One of the challenges is that most biosynthetic pathways of PNPs are still unknown, which largely limits the number of candidate PNPs for heterologous microbial production. Another challenge is that the metabolic fluxes toward the target products in microbial hosts are often hindered by poor precursor supply, low catalytic activity of enzymes and obstructed product transport. Consequently, despite intensive studies on the metabolic engineering of microbial hosts, the fermentation costs of most heterologously produced PNPs are still too high for industrial-scale production. In this paper, we review several aspects of PNP production in microbial cell factories, including important design principles and recent progress in pathway mining and metabolic engineering. In addition, implemented cases of industrial-scale production of PNPs in microbial cell factories are also highlighted.

  11. A tau-charm-factory at Argonne

    International Nuclear Information System (INIS)

    Norem, J.; Repond, J.

    1994-01-01

    In this paper we explore the possibility of building a tau-charm-factory at the Argonne National Laboratory. A tau-charm-factory is an e + e - collider with a center-of-mass energy between 3.0 GeV and 5.0 GeV and a luminosity of at least 1 x 10 33 cm -2 s -1 . Once operational, the facility will produce large samples of τ pairs, charm mesons, and charmonium with either negligible or well understood backgrounds. This will lead to high precision measurements in the second generation quark and the third generation lepton sectors that cannot be done at other facilities. Basic physical properties and processes, such as the tau neutrino mass, rare tau decays, charm decay constants, rare charm meson decays, neutral D 0 -- meson mixing, and many more will be studied with unique precision. An initial design of the collider including the injector system is described. The design shows that a luminosity of at least 1 x 10 33 cm -2 s -1 can be achieved over the entire center-of-mass energy range of the factory

  12. The design of a small linear-resonant, split Stirling cryogenic refrigerator compressor

    Science.gov (United States)

    Ackermann, R. A.

    1985-01-01

    The development of a small linear-resonant compressor for use in a 1/4-watt, 78K, split Stirling cryogenic refrigerator is discussed. The compressor contains the following special features: (1) a permanent-magnet linear motor; (2) resonant dynamics; (3) dynamic balancing; and (4) a close-clearance seal between the compressor piston and cylinder. This paper describes the design of the compressor, and presents component test data and system test data for the compressor driving a 1/4-watt expander.

  13. Optimization of LDL targeted nanostructured lipid carriers of 5-FU by a full factorial design

    Directory of Open Access Journals (Sweden)

    Sare Andalib

    2012-01-01

    Full Text Available Background: Nanostructured lipid carriers (NLC are a mixture of solid and liquid lipids or oils as colloidal carrier systems that lead to an imperfect matrix structure with high ability for loading water soluble drugs. The aim of this study was to find the best proportion of liquid and solid lipids of different types for optimization of the production of LDL targeted NLCs used in carrying 5-Fu by the emulsification-solvent evaporation method. Materials and Methods: The influence of the lipid type, cholesterol or cholesteryl stearate for targeting LDL receptors, oil type (oleic acid or octanol, lipid and oil% on particle size, surface charge, drug loading efficiency, and drug released percent from the NLCs were studied by a full factorial design. Results: The NLCs prepared by 54.5% cholesterol and 25% of oleic acid, showed optimum results with particle size of 105.8 nm, relatively high zeta potential of −25 mV, drug loading efficiency of 38% and release efficiency of about 40%. Scanning electron microscopy of nanoparticles confirmed the results of dynamic light scattering method used in measuring the particle size of NLCs. Conclusions: The optimization method by a full factorial statistical design is a useful optimization method for production of nanostructured lipid carriers.

  14. INFLUENCE BY ARTIFICIAL DEFOLIATION AND NPK FERTILIZER ...

    African Journals Online (AJOL)

    Dr. K.E. Law-Ogbomo

    main plot, defoliation (sub-plot) and time of defoliation (sub- sub plot). ... using analysis of variance procedure for splitsplit plot design and means were ... The interaction between NPK fertilizer application and defoliation was only .... yield components (number of dry pod per plant, number of seeds per pod and plant).

  15. INDOOR THERMAL CONDITION OF FACTORY BUILDING IN BANGLADESH

    Directory of Open Access Journals (Sweden)

    Muhammed Abdullah Al Sayem Khan

    2011-12-01

    Full Text Available Bangladesh is a developing country and has a lot of factories for different products for local use and also export to abroad. Garments industries are one of the top most items of exported items. A huge number of populations are working in garments industries. But these factories are not well designed in sense of the thermal environment. Workers experiences sickness related to indoor environment. The productions of these factories are affected due to employees’ health condition. The research is done in two different methods. One is empirical data collection using thermal data loggers and the other is questionnaire survey on the spots for three factory buildings. The field study was conducted in four different months of the same year during winter and summer period. Expected findings of this research are that the indoor environment is not comfortable for works at day time during summer season. This research will help the factory workers in providing a comfortable thermal environment and also help the employers or factory owners to increase their production margin.

  16. Design and Factory Test of the E /E- Frascati Linear Accelerator for DAFNE

    Energy Technology Data Exchange (ETDEWEB)

    Anamkath, H.; Lyons, S.; Nett, D.; Treas, P.; Whitham, K.; Zante, T.; /Titan Beta, Dublin; Miller, R.; /Titan Beta, Dublin /SLAC; Boni, R.; Hsieh, H.; Sannibale, F.; Vescovi, M.; Vignola, G.; /Frascati

    2011-11-28

    The electron-positron accelerator for the DAFNE project has been built and is in test at Titan Beta in Dublin, CA. This S-Band RF linac system utilizes four 45 MW sledded klystrons and 16-3 m accelerating structures to achieve the required performance. It delivers a 4 ampere electron beam to the positron converter and accelerates the resulting positrons to 550 MeV. The converter design uses a 4.3T pulsed tapered flux compressor along with a pseudo-adiabatic tapered field to a 5 KG solenoid over the first two positron accelerating sections. Quadrupole focusing is used after 100 MeV. The system performance is given in Table 1. This paper briefly describes the design and development of the various subassemblies in this system and gives the initial factory test data.

  17. Design and characterization of a novel toroidal split-ring resonator

    International Nuclear Information System (INIS)

    Bobowski, J. S.; Nakahara, Hiroko

    2016-01-01

    The design and characterization of a novel toroidal split-ring resonator (SRR) are described in detail. In conventional cylindrical SRRs, there is a large magnetic flux within the bore of the resonator. However, there also exists a non-negligible magnetic flux in the free space surrounding the resonator. The energy losses associated with this radiated power diminish the resonator’s quality factor. In the toroidal SRR, on the other hand, the magnetic field lines are strongly confined within the bore of the resonator resulting in high intrinsic quality factors and stable resonance frequencies without requiring additional electromagnetic shielding. This paper describes the design and construction of a toroidal SRR as well as an experimental investigation of its cw response in the frequency-domain and its time-domain response to a rf pulse. Additionally, the dependence of the toroidal SRR’s resonant frequency and quality factor on the strength of inductive coupling to external circuits is investigated both theoretically and experimentally

  18. Barrier erosion control test plan: Gravel mulch, vegetation, and soil water interactions

    Energy Technology Data Exchange (ETDEWEB)

    Waugh, W.J.; Link, S.O. (Pacific Northwest Lab., Richland, WA (USA))

    1988-07-01

    Soil erosion could reduce the water storage capacity of barriers that have been proposed for the disposal of near-surface waste at the US Department of Energy's Hanford Site. Gravel mixed into the top soil surface may create a self-healing veneer that greatly retards soil loss. However, gravel admixtures may also enhance infiltration of rainwater, suppress plant growth and water extraction, and lead to the leaching of underlying waste. This report describes plans for two experiments that were designed to test hypotheses concerning the interactive effects of surface gravel admixtures, revegetation, and enhanced precipitation on soil water balance and plant abundance. The first experiment is a factorial field plot set up on the site selected as a soil borrow area for the eventual construction of barriers. The treatments, arranged in a a split-split-plot design structure, include two densities of gravel admix, a mixture of native and introduced grasses, and irrigation to simulate a wetter climate. Changes in soil water storage and plant cover are monitored with neutron moisture probes and point intercept sampling, respectively. The second experiment consists of an array of 80 lysimeters containing several different barrier prototypes. Surface treatments are similar to the field-plot experiment. Drainage is collected from a valve at the base of each lysimeter tube, and evapotranspiration is estimated by subtraction. The lysimeters are also designed to be coupled to a whole-plant gas exchange system that will be used to conduct controlled experiments on evapotranspiration for modeling purposes. 56 refs., 6 figs., 8 tabs.

  19. An asymmetric B factory based on PEP

    International Nuclear Information System (INIS)

    1991-02-01

    In this report we describe a design for a high-luminosity Asymmetric B Factory to be built in the PEP tunnel on the SLAC site. This proposal, a collaborative effort SLAC, LBL, and LLNL, is the culmination of more than two years of effort aimed at the design and construction of an asymmetric e + e - collider capable of achieving a luminosity of L = 3 x 10 33 cm -2 s -1 . The configuration adopted utilizes two storage rings, and electron ring operating at 9 GeV and a positron ring at 3.1 GeV, each with a circumference of 2200 m. The high-energy ring is an upgrade of the PEP storage ring at SLAC; all PEP magnets and most power supplies will be reused. The upgrade consists primarily of replacing the PEP vacuum chamber and RF system with newly designed versions optimized for the high-current environment of the B Factory. The low-energy ring will be newly constructed and will be situated atop the high-energy ring in the PEP tunnel. Utilities already installed in the PEP tunnel are largely sufficient to operate the two B Factory storage rings

  20. CHANGES IN THE CHARACTERISTICS OF ‘PRATA’ BANANA TREATED WITH CYTOKININ AND GIBBERELLIN

    Directory of Open Access Journals (Sweden)

    JULIANA DOMINGUES LIMA

    Full Text Available ABSTRACT Plant growth regulators can influence fruit yield and quality. This study aimed to evaluate the effect of cytokinin and gibberelin on the agronomic and physicochemical characteristics of banana fruits cv. ‘Prata’ (Musa spp. AAB, according to the formation period and position in the bunch. The experiment was conducted in a completely randomized 2 x 5 factorial design, two periods of bunch development (summer and winter, five treatments and ten replicates. To study the effect of position in the bunch, split plot was adopted, considering in the plot, 2 x 5 factorial and in subplots, hand 1, hand 4 and last hand. Treatments consisted of 2 pulverizations with water, 150 mg L-1 cytokinin, 200 mg L-1 of gibberellic acid, 100 mg L-1 of cytokinin plus 200 mg L-1 of gibberellic acid and 200 mg L-1 of cytokinin plus 200 mg L-1 of gibberellic acid, applied from the fourth to the last hand of the bunch. Cytokinin and gibberellin, alone or associated, regardless of formation period and position, did not affect the size and physicochemical characteristics of fruits, only delayed the bunch harvest.

  1. NPLOT - NASTRAN PLOT

    Science.gov (United States)

    Mcentire, K.

    1994-01-01

    NPLOT is an interactive computer graphics program for plotting undeformed and deformed NASTRAN finite element models (FEMs). Although there are many commercial codes already available for plotting FEMs, these have limited use due to their cost, speed, and lack of features to view BAR elements. NPLOT was specifically developed to overcome these limitations. On a vector type graphics device the two best ways to show depth are by hidden line plotting or haloed line plotting. A hidden line algorithm generates views of models with all hidden lines removed, and a haloed line algorithm displays views with aft lines broken in order to show depth while keeping the entire model visible. A haloed line algorithm is especially useful for plotting models composed of many line elements and few surface elements. The most important feature of NPLOT is its ability to create both hidden line and haloed line views accurately and much more quickly than with any other existing hidden or haloed line algorithms. NPLOT is also capable of plotting a normal wire frame view to display all lines of a model. NPLOT is able to aid in viewing all elements, but it has special features not generally available for plotting BAR elements. These features include plotting of TRUE LENGTH and NORMALIZED offset vectors and orientation vectors. Standard display operations such as rotation and perspective are possible, but different view planes such as X-Y, Y-Z, and X-Z may also be selected. Another display option is the Z-axis cut which allows a portion of the fore part of the model to be cut away to reveal details of the inside of the model. A zoom function is available to terminals with a locator (graphics cursor, joystick, etc.). The user interface of NPLOT is designed to make the program quick and easy to use. A combination of menus and commands with help menus for detailed information about each command allows experienced users greater speed and efficiency. Once a plot is on the screen the interface

  2. Application of factorial design for the ab initio study of cis- and trans-1,2 dihaloethylene stabilities

    Directory of Open Access Journals (Sweden)

    Silva João Bosco P. da

    2000-01-01

    Full Text Available The chemometric technique Two Level Factorial Design was used to evaluate the principal and interaction effects of wave function modifications on calculated energy differences (DE between the cis and trans isomers of 1,2-dihaloethylenes, C2H2X2 (X=F and Cl. The factorial profile of DE is quite different for these systems. The addition of polarization and diffuse functions to the basis set have the largest effects in describing cis 1,2-difluoroethylene as the most stable isomer. In contrast electronic correlation, at the MP2 level, and the inclusion of polarization functions in the basis set have the largest effects in describing the cis form as the most stable one in the 1,2-dichloroethylenes. In both systems the interaction effects are smaller than the principal effects.

  3. Slope Stability of Geosynthetic Clay Liner Test Plots

    Science.gov (United States)

    Fourteen full-scale field test plots containing five types of geosynthetic clay liners (GCLs) were constructed on 2H:IV and 3H:IV slopes for the purpose of assessing slope stability. The test plots were designed to simulate typical final cover systems for landfill. Slides occurr...

  4. Embryo splitting

    Directory of Open Access Journals (Sweden)

    Karl Illmensee

    2010-04-01

    Full Text Available Mammalian embryo splitting has successfully been established in farm animals. Embryo splitting is safely and efficiently used for assisted reproduction in several livestock species. In the mouse, efficient embryo splitting as well as single blastomere cloning have been developed in this animal system. In nonhuman primates embryo splitting has resulted in several pregnancies. Human embryo splitting has been reported recently. Microsurgical embryo splitting under Institutional Review Board approval has been carried out to determine its efficiency for blastocyst development. Embryo splitting at the 6–8 cell stage provided a much higher developmental efficiency compared to splitting at the 2–5 cell stage. Embryo splitting may be advantageous for providing additional embryos to be cryopreserved and for patients with low response to hormonal stimulation in assisted reproduction programs. Social and ethical issues concerning embryo splitting are included regarding ethics committee guidelines. Prognostic perspectives are presented for human embryo splitting in reproductive medicine.

  5. Effect of Plant Density, Rate and Split Application of Nitrogen Fertilizer on Quality Characteristics and Nitrogen Use Efficiency of Safflower under Weed Competition

    Directory of Open Access Journals (Sweden)

    M Fuladvand

    2015-09-01

    Full Text Available In order to evaluation of plant density, rate and method of nitrogen fertilizer split application on quality characteristics and nitrogen use efficiency of safflower (Sofeh variety under weed competition a field experiment was carried out in field research Yasouj University in 2013. This experiment was a factorial based on randomized complete block design with three replications. First factor was a two levels plant density (20 and 40 plants m-2 and second factor was nitrogen rate application on nine levels. That included; non nitrogen application and 75 and 150 kgN ha-1 nitrogen application that both used with four split method. Split methods were included; S1 (%50 in pre planting stage - %50 in stem elongation stage, S2 (%25 in pre planting stage - %75 in stem elongation stage, S3 (%25 in pre planting stage - %50 in stem elongation stage -%25 in flowering stage and S4 (%25 in pre planting stage - %25 in stem elongation stage - %25 in flowering stage. Also in this experiment, weed did not control. Results showed that whit increasing crop density, oil yield and protein grain yield increased by 20 percent and nitrogen utilization efficiency increased by 10 percent. The highest oil yield (50.25 g m-2 was obtained from 75 kg ha-1 nitrogen with three-stage split application (S4. Finally, results showed that increasing nitrogen fertilizer application decreased nitrogen utilization efficiency but three-stage split method application increased this trait.

  6. Design and Experiment of a Differential-Based Power Split Device

    Directory of Open Access Journals (Sweden)

    Xiaohua Zeng

    2014-04-01

    Full Text Available Hybrid electric vehicles have excellent energy efficiency and emission performance. Power split device (PSD is a key component that directly affects the control strategy of power systems, the economic consumption of fuel, and the dynamic performance of vehicles. A differential-based PSD was proposed in this paper. A traditional differential was taken as the prototype and a new design method is proposed to retrofit the differential into a PSD. First, a comprehensive approach that includes theoretical analysis and software simulation was used to analyze the possibility as well as the necessity of retrofitting the differential into PSD. Then the differential was retrofitted. Finally, finite element analysis and bench test were conducted. Results showed that applying the retrofitted differential as PSD is practicable.

  7. Test results of distributed ion pump designs for the PEP-II Asymmetric B-Factory collider

    Energy Technology Data Exchange (ETDEWEB)

    Calderon, M.; Holdener, F.; Peterson, D. [Lawrence Livermore National Lab., CA (United States)] [and others

    1994-07-01

    The testing facility measurement methods and results of prototype distributed ion pump (DIP) designs for the PEP-II B-Factory High Energy Ring are presented. Two basic designs with 5- or 7-anode plates were tested at LLNL with penning cell sizes of 15, 18, and 21 mm. Direct comparison of 5- and 7-plate anodes with 18 mm holes shows increased pumping speed with the 7-plate design. The 5-plate, 18 mm and 7-plate, 15 mm designs both gave an average pumping speed of 135 1/s/m at 1 {times} 10{sup {minus}8} Torr nitrogen base pressure in a varying 0.18 T peak B-field. Comparison of the three hole sizes indicates that cells smaller than the 15 mm tested can be efficiently used to obtain higher pumping speeds for the same anode plate sizes used.

  8. Test results of distributed ion pump designs for the PEP-II Asymmetric B-Factory collider

    International Nuclear Information System (INIS)

    Calderon, M.; Holdener, F.; Peterson, D.

    1994-07-01

    The testing facility measurement methods and results of prototype distributed ion pump (DIP) designs for the PEP-II B-Factory High Energy Ring are presented. Two basic designs with 5- or 7-anode plates were tested at LLNL with penning cell sizes of 15, 18, and 21 mm. Direct comparison of 5- and 7-plate anodes with 18 mm holes shows increased pumping speed with the 7-plate design. The 5-plate, 18 mm and 7-plate, 15 mm designs both gave an average pumping speed of 135 1/s/m at 1 x 10 -8 Torr nitrogen base pressure in a varying 0.18 T peak B-field. Comparison of the three hole sizes indicates that cells smaller than the 15 mm tested can be efficiently used to obtain higher pumping speeds for the same anode plate sizes used

  9. Using factorial experimental design to evaluate the separation of plastics by froth flotation.

    Science.gov (United States)

    Salerno, Davide; Jordão, Helga; La Marca, Floriana; Carvalho, M Teresa

    2018-03-01

    This paper proposes the use of factorial experimental design as a standard experimental method in the application of froth flotation to plastic separation instead of the commonly used OVAT method (manipulation of one variable at a time). Furthermore, as is common practice in minerals flotation, the parameters of the kinetic model were used as process responses rather than the recovery of plastics in the separation products. To explain and illustrate the proposed methodology, a set of 32 experimental tests was performed using mixtures of two polymers with approximately the same density, PVC and PS (with mineral charges), with particle size ranging from 2 to 4 mm. The manipulated variables were frother concentration, air flow rate and pH. A three-level full factorial design was conducted. The models establishing the relationships between the manipulated variables and their interactions with the responses (first order kinetic model parameters) were built. The Corrected Akaike Information Criterion was used to select the best fit model and an analysis of variance (ANOVA) was conducted to identify the statistically significant terms of the model. It was shown that froth flotation can be used to efficiently separate PVC from PS with mineral charges by reducing the floatability of PVC, which largely depends on the action of pH. Within the tested interval, this is the factor that most affects the flotation rate constants. The results obtained show that the pure error may be of the same magnitude as the sum of squares of the errors, suggesting that there is significant variability within the same experimental conditions. Thus, special care is needed when evaluating and generalizing the process. Copyright © 2017 Elsevier Ltd. All rights reserved.

  10. BERKELEY/STANFORD: B factory plans

    International Nuclear Information System (INIS)

    Anon.

    1991-01-01

    For the past several years, accelerator physicists at Lawrence Berkeley Laboratory (LBL) and the Stanford Linear Accelerator Center (SLAC) have been involved in the design of an Asymmetric B Factory to be sited in the tunnel of the PEP electron-positron collider at SLAC

  11. Atmospheric deposition of trace elements around point sources and human health risk assessment. II: Uptake of arsenic and chromium by vegetables grown near a wood preservation factory

    DEFF Research Database (Denmark)

    Larsen, Erik Huusfeldt; Moseholm, Lars; Nielsen, Margot M.

    1992-01-01

    Kale, lettuce, carrots and potatoes were grown in 20 experimental plots surrounding a wood preservation factory, to investigate the amount and pathways for plant uptake of arsenic and chromium. Arsenate used in the wood preservation process is converted to the more toxic arsenite by incineration...... of waste wood and is emitted into the atmosphere. Elevated concentrations of inorganic arsenic and chromium were found both in the test plants and in the soil around the factory. Multivariate statistical analysis of the results indicated that the dominating pathway of arsenic and chromium from the factory...

  12. Optimization of wood flour acetylation by factorial design and partial least squares regression

    Directory of Open Access Journals (Sweden)

    Lisandra M. K. Nadal

    2012-01-01

    Full Text Available Acetylation was performed to reduce the polarity of wood and increase its compatibility with polymer matrices for the production of composites. These reactions were performed first as a function of acetic acid and anhydride concentration in a mixture catalyzed by sulfuric acid. A concentration of 50%/50% (v/v of acetic acid and anhydride was found to produced the highest conversion rate between the functional groups. After these reactions, the kinetics were investigated by varying times and temperatures using a 3² factorial design, and showed time was the most relevant parameter in determining the conversion of hydroxyl into carbonyl groups.

  13. CrossRef Neutrino factory proton driver and target design

    CERN Document Server

    Garoby, Roland; Thomason, John; Davenne, Tristan; Caretta, Ottone; Back, John J

    2016-01-01

    Neutrinos are very elusive particles belonging to the lepton family. They exist in different types corresponding to the different charged leptons, namely electrons, muons and taus. Contrary to electrons, neutrinos hardly interact with matter which makes them very difficult to detect and study. To the best of today’s knowledge, neutrinos have hardly any mass and they can change from one type to another (so-called “neutrino oscillation”). Most physicists think that this oscillation occurs because neutrinos have mass. A Neutrino Factory [1] is a special facility producing a large amount of neutrinos every year (typically 10$^{21}$ neutrinos/year). Its main purpose is to study the change of type of neutrinos between the place where they are generated and a remote location. In a Neutrino Factory, neutrinos result from the decay of muons, unstable particles with a mean lifetime of 2.2 $\\mu$s in their rest frame. Sharp beams of high energy neutrinos are obtained at the end of the long straight sections of a mu...

  14. An asymmetric B factory based on PEP

    Energy Technology Data Exchange (ETDEWEB)

    1991-02-01

    In this report we describe a design for a high-luminosity Asymmetric B Factory to be built in the PEP tunnel on the SLAC site. This proposal, a collaborative effort SLAC, LBL, and LLNL, is the culmination of more than two years of effort aimed at the design and construction of an asymmetric e{sup +}e{sup {minus}} collider capable of achieving a luminosity of L = 3 {times} 10{sup 33} cm{sup {minus}2} s{sup {minus}1}. The configuration adopted utilizes two storage rings, and electron ring operating at 9 GeV and a positron ring at 3.1 GeV, each with a circumference of 2200 m. The high-energy ring is an upgrade of the PEP storage ring at SLAC; all PEP magnets and most power supplies will be reused. The upgrade consists primarily of replacing the PEP vacuum chamber and RF system with newly designed versions optimized for the high-current environment of the B Factory. The low-energy ring will be newly constructed and will be situated atop the high-energy ring in the PEP tunnel. Utilities already installed in the PEP tunnel are largely sufficient to operate the two B Factory storage rings.

  15. Particulate photocatalysts for overall water splitting

    Science.gov (United States)

    Chen, Shanshan; Takata, Tsuyoshi; Domen, Kazunari

    2017-10-01

    The conversion of solar energy to chemical energy is a promising way of generating renewable energy. Hydrogen production by means of water splitting over semiconductor photocatalysts is a simple, cost-effective approach to large-scale solar hydrogen synthesis. Since the discovery of the Honda-Fujishima effect, considerable progress has been made in this field, and numerous photocatalytic materials and water-splitting systems have been developed. In this Review, we summarize existing water-splitting systems based on particulate photocatalysts, focusing on the main components: light-harvesting semiconductors and co-catalysts. The essential design principles of the materials employed for overall water-splitting systems based on one-step and two-step photoexcitation are also discussed, concentrating on three elementary processes: photoabsorption, charge transfer and surface catalytic reactions. Finally, we outline challenges and potential advances associated with solar water splitting by particulate photocatalysts for future commercial applications.

  16. Meson factories

    International Nuclear Information System (INIS)

    Dicello, J.F.; Zaider, M.; Bradbury, J.N.

    1979-01-01

    Technological improvements in accelerator design in the 1960's resulted in the capability to develop medium-energy proton accelerators with beam intensities of almost 1 mA. These beams are able to produce fluxes of secondary particles, including pions, muons, neutrinos, and neutrons, which are as much as 10,000 times as intense as those previously available. Those machines built for optimum meson production are commonly called meson factories. The characteristics of these facilities are reviewed, and the present programs in applied research, and some potential areas of future work are discussed

  17. Application of full 42 Factorial Design for the Development and Characterization of Insecticidal Soap from Neem Oil

    Directory of Open Access Journals (Sweden)

    A. S. KOVO

    2006-01-01

    Full Text Available The aim of this paper was to investigate the extraction, characterization and production of insecticidal soap from Neem oil using full 42 factorial design. Soxhlet extractor was used for the extraction purpose and two solvent was chosen to determine which is better. N-hexane gives a Neem oil yield of 45.43% while ethanol gives a yield of 46.38%, confirming the earlier literature result giving ethanol as better solvent for Neem oil extraction. The basic properties of the oil were determined as follows, saponification value 215.95ml/g, acid value 1.122g/mol, unsaponifiable matter 19.66 etc. The Neem oil was found to have a colour of golden yellow due to the presence of Nimbidin.Full 42 factorial design and mathematical model was applied to the extraction process and a first order regression equation of the form:Y = 9.548 + 0.144X1 + 0.1931X2 + 0.1892 X12was obtained growing the individual effect of time and solvent type as parameter and their interaction in the entire extraction process the Neem insecticidal soap was found to be effective in insect and pest control.

  18. Physics at e+e- factories

    International Nuclear Information System (INIS)

    Lueth, V.; MacFarlane, D.B.

    1991-02-01

    Feasible designs are well advanced for high-luminosity e + e - storage rings which produce B 0 bar B 0 pairs either at rest or, in what appears to be a more promising option, boosted in the detector frame. Facilities which could provide samples of 30--100 fb -1 per year on the Υ(4S) will be proposed in early 1991. Here we examine the principal physics goal of such B Factories, namely CP violation in the b system. Methods in a variety of channels, estimated event samples, and detector requirements are all considered. We conclude that the physics argument for an e + e - B Factory is well documented, and compelling. 50 refs., 22 figs., 10 tabs

  19. The participation of the Experimental Design Factory of the Uranium Industry of Czechoslovakia in the design of a tunneling machine with disk bits

    Energy Technology Data Exchange (ETDEWEB)

    Kastner, P

    1983-01-01

    A tunneling machine, two prototypes of which were designed and built jointly on the basis of scientific and technical cooperation between the Experimental Design Factory of the Uranium Industry of Czechoslovakia and the VEB-Schachtbau enterprise (East Germany), is described. The experimental design operations were conducted under the methodological leadership of the Mine Construction in the Uranium Industry (Czechoslovakia) enterprise. The experimental design factory developed a general design system for the machine and its individual subassemblies. The detailed technical documentation for the machine units was developed by both enterprises. Each enterprise made two complexes of specific units and spare parts. The prototypes were assembled in both countries with the technical assistance of the producer enterprise of the appropriate subassembly. Industrial tests were conducted by each enterprise independently with technical assistance and delivery of spare parts on the part of the producer enterprise. A machine under the title of VM 24-27 was used to drill more than 2,300 meters of water supply tunnel in East Germany in 1982 and a machine called the RS 24-27 (29) was used in Prague in the same year to drill approximately 1,400 meters of cable collectors. The machine is designed for the passage of rounded mine drifts with a diameter of 2.4 to 2.7 (2.9) meters) to the full cross section in stable rocks. Its overall length is 32.5 meters, while the total weight is 85 tons. The shift productivity was 9.55 meters. Since 1979 the Mining Construction in the Uranium Industry and the Experimental Design Plant of the Uranium Industry Enterprises of Czechoslovakia have supplied disk bits for the TVM Demag tunnel drilling machines (West Germany) and RS 24-27 and the HG 210 Wirth (West Germany) cross cut drills.

  20. Factory physics

    CERN Document Server

    Hopp, Wallace J.

    2011-01-01

    After a brief introductory chapter, "Factory Physics 3/e" is divided into three parts: I - The Lessons of History; II - Factory Physics; and III - Principles in Practice. The scientific approach to manufacturing and supply chain management, developed in Part II, is unique to this text. No other text or professional book provides a rigorous, principles-based foundation for manufacturing management. The Third Edition offers tighter connections between Lean Manufacturing, MRP/ERP, Six Sigma, Supply Chain Management, and Factory Physics. In addition to enhancing the historical overview of how these systems evolved, the authors show explicitly how users can achieve Lean Manufacturing objectives (faster response, less inventory) using the integration aspects of MRP/ERP/SCM systems along with the variance analysis methods of Six Sigma. Factory Physics provides the overarching framework that coordinates all of these initiatives into a single-focused strategy.

  1. Manufacturing data analytics using a virtual factory representation.

    Science.gov (United States)

    Jain, Sanjay; Shao, Guodong; Shin, Seung-Jun

    2017-01-01

    Large manufacturers have been using simulation to support decision-making for design and production. However, with the advancement of technologies and the emergence of big data, simulation can be utilised to perform and support data analytics for associated performance gains. This requires not only significant model development expertise, but also huge data collection and analysis efforts. This paper presents an approach within the frameworks of Design Science Research Methodology and prototyping to address the challenge of increasing the use of modelling, simulation and data analytics in manufacturing via reduction of the development effort. The use of manufacturing simulation models is presented as data analytics applications themselves and for supporting other data analytics applications by serving as data generators and as a tool for validation. The virtual factory concept is presented as the vehicle for manufacturing modelling and simulation. Virtual factory goes beyond traditional simulation models of factories to include multi-resolution modelling capabilities and thus allowing analysis at varying levels of detail. A path is proposed for implementation of the virtual factory concept that builds on developments in technologies and standards. A virtual machine prototype is provided as a demonstration of the use of a virtual representation for manufacturing data analytics.

  2. Photoelectrochemical water splitting: optimizing interfaces and light absorption

    NARCIS (Netherlands)

    Park, Sun-Young

    2015-01-01

    In this thesis several photoelectrochemical water splitting devices based on semiconductor materials were investigated. The aim was the design, characterization, and fabrication of solar-to-fuel devices which can absorb solar light and split water to produce hydrogen.

  3. Tamarind seed gum-hydrolyzed polymethacrylamide-g-gellan beads for extended release of diclofenac sodium using 32 full factorial design.

    Science.gov (United States)

    Nandi, Gouranga; Nandi, Amit Kumar; Khan, Najim Sarif; Pal, Souvik; Dey, Sibasish

    2018-07-15

    Development of tamarind seed gum (TSG)-hydrolyzed polymethacrylamide-g-gellan (h-Pmaa-g-GG) composite beads for extended release of diclofenac sodium using 3 2 full factorial design is the main purpose of this study. The ratio of h-Pmaa-g-GG and TSG and concentration of cross-linker CaCl 2 were taken as independent factors with three different levels of each. Effects of polymer ratio and CaCl 2 on drug entrapment efficiency (DEE), drug release, bead size and swelling were investigated. Responses such as DEE and different drug release parameters were statistically analyzed by 3 2 full factorial design using Design-Expert software and finally the formulation factors were optimized to obtain USP-reference release profile. Drug release rate was found to decrease with decrease in the ratio of h-Pmaa-g-GG:TSG and increase in the concentration of Ca 2+ ions in cross-linking medium. The optimized formulation showed DEE of 93.25% and an extended drug release profile over a period of 10h with f 2 =80.13. Kinetic modeling unveiled case-I-Fickian diffusion based drug release mechanism. Copyright © 2018 Elsevier B.V. All rights reserved.

  4. Test results of pre-production prototype distributed ion pump design for the PEP-II Asymmetric B-Factory collider

    Energy Technology Data Exchange (ETDEWEB)

    Holdener, F.R.; Behne, D.; Hathaway, D. [and others

    1995-04-24

    We have built and tested a plate-type pre-production distributed Ion Pump (DIP) for the PEP-II B-Factory High Energy Ring (HER). The design has been an earlier design to use less materials and to costs. Penning cell hole sizes of 15, 18, and 21 mm have been tested in a uniform magnetic field of 0.18 T to optimize pumping speed. The resulting final DIP design consisting of a 7-plate, 15 mm basic cell size anode was magnetic field of the HER dipole. A description of the final optimized DIP design will be presented along with the test results of the pumping speed measurements.

  5. arXiv Laura++ : a Dalitz plot fitter

    CERN Document Server

    Back, John; Harrison, Paul; Latham, Thomas; O'Hanlon, Daniel; Qian, Wenbin; del Amo Sanchez, Pablo; Craik, Daniel; Ilic, Jelena; Otalora Goicochea, Juan; Puccio, Eugenia; Silva Coutinho, Rafael; Whitehead, Mark

    The Dalitz plot analysis technique has become an increasingly important method in heavy flavour physics. The Laura++ fitter has been developed as a flexible tool that can be used for Dalitz plot analyses in different experimental environments. Explicitly designed for three-body decays of heavy-flavoured mesons to spinless final state particles, it is optimised in order to describe all possible resonant or nonresonant contributions, and to accommodate possible CP violation effects.

  6. JINR studies for a Tau-Charm Factory

    International Nuclear Information System (INIS)

    Chelkov, G.

    1994-01-01

    This paper touches on work being done a JINR relevant to a proposal for construction of a tau charm factory, and its attendant detector system. A workshop on such a device was held at JINR in 1992, and here the author touches on questions of what one wants to learn about tau particles from such a machine, the charge to the group looking at a detector design for such a facility, the general conclusions of the JINR study, and a status report of work on the JINR Tau Charm Factory project

  7. Particle physics prospects for the KAON factory

    International Nuclear Information System (INIS)

    Bryman, D.

    1989-05-01

    The Kaon Factory at TRIUMF will produce beams of kaons, antiprotons, neutrinos and other particles with a hundred-fold increase in intensity over existing machines in the 30 GeV region. This will make possible new high precision experiments designed to test current ideas as well as high sensitivity measurements which could potentially reveal new effects. A sample of particle physics experiments involving rare kaon decays, CP and T violation studies, neutrino properties and reactions and light quark spectroscopy which might take advantage of the new opportunities presented by the Kaon Factory is discussed

  8. Cell Factory Engineering

    DEFF Research Database (Denmark)

    Davy, Anne Mathilde; Kildegaard, Helene Faustrup; Andersen, Mikael Rørdam

    2017-01-01

    focused on individual strategies or cell types, but collectively they fall under the broad umbrella of a growing field known as cell factory engineering. Here we condense >130 reviews and key studies in the art into a meta-review of cell factory engineering. We identified 33 generic strategies......-review provides general strategy guides for the broad range of applications of rational engineering of cell factories....

  9. Optimization of thiamethoxam adsorption parameters using multi-walled carbon nanotubes by means of fractional factorial design.

    Science.gov (United States)

    Panić, Sanja; Rakić, Dušan; Guzsvány, Valéria; Kiss, Erne; Boskovic, Goran; Kónya, Zoltán; Kukovecz, Ákos

    2015-12-01

    The aim of this work was to evaluate significant factors affecting the thiamethoxam adsorption efficiency using oxidized multi-walled carbon nanotubes (MWCNTs) as adsorbents. Five factors (initial solution concentration of thiamethoxam in water, temperature, solution pH, MWCNTs weight and contact time) were investigated using 2V(5-1) fractional factorial design. The obtained linear model was statistically tested using analysis of variance (ANOVA) and the analysis of residuals was used to investigate the model validity. It was observed that the factors and their second-order interactions affecting the thiamethoxam removal can be divided into three groups: very important, moderately important and insignificant ones. The initial solution concentration was found to be the most influencing parameter on thiamethoxam adsorption from water. Optimization of the factors levels was carried out by minimizing those parameters which are usually critical in real life: the temperature (energy), contact time (money) and weight of MWCNTs (potential health hazard), in order to maximize the adsorbed amount of the pollutant. The results of maximal adsorbed thiamethoxam amount in both real and optimized experiments indicate that among minimized parameters the adsorption time is one that makes the largest difference. The results of this study indicate that fractional factorial design is very useful tool for screening the higher number of parameters and reducing the number of adsorption experiments. Copyright © 2015 Elsevier Ltd. All rights reserved.

  10. Rabi splitting in an acoustic cavity embedded plate

    International Nuclear Information System (INIS)

    Ni, Xu; Liu, Xiao-Ping; Chen, Ze-Guo; Zheng, Li-Yang; Xu, Ye-Long; Lu, Ming-Hui; Chen, Yan-Feng

    2014-01-01

    We design a structure to realize Rabi splitting and Rabi oscillation in acoustics. We develop rigorous analytical models to analyze the splitting effect from the aspect of phase matching, and from the aspect of mode coupling using a coupled mode model. In this model, we discover that the splitting effect is caused by the coupling of the Fabry–Perot fundamental mode with the resonant mode of an artificial acoustic ‘atom’. We then extract the coupling strength and analyze the impact of structural parameters on it. In addition, we demonstrate Rabi oscillation in the time domain. Such quantum phenomena in the classical regime may have potential applications in the design of novel ultrasonic devices.

  11. Application of fractional factorial design to improve hot smoked Nile Perch (Lates niloticus quality

    Directory of Open Access Journals (Sweden)

    Sokamté, T.A.

    2017-06-01

    Full Text Available The aim of this research was to study the parameters influencing moisture, salt and total phenol content of hot smoked Nile Perch and to compare the influence of processing conditions on its proximate composition and sensory quality. The effect on moisture, salt and total phenol content was investigated using fractional factorial design with seven factors and two levels: X1 for brine concentration, X2 for brining time, X3 for preliminary smoking-drying time, X4 for smoking time, X5 for hot smoking time, X6 for smoking temperature and X7 for hot smoking temperature. A Multiple Linear Regression Analysis was performed to fit the mathematical model to the collected data and the model tested using analysis of variance (ANOVA. Results of ANOVA indicated the good accuracy and highest significance of the mathematical model. The range of total protein and lipid content was 17.96 to 34.34% and 0.87 to 4.43%, respectively. The range of general acceptability of smoked Nile Perch was 4.6 to 8.2 based on 9-point hedonic scale. Based on the results obtained, including the overall acceptability, proximate composition and smoking criteria of finished product, samples produced with the following conditions: brining at 4% for 270min, drying at 30°C for 30min and the smoked time/temperature cycles following: 30°C/120min; 50°C/240min and 80°C/240min was the best and most accepted. The results derived from this study indicate that the fractional factorial design is a useful screening tool for improving industrial smoking process of Nile Perch.

  12. Photocatalytic water splitting: Quantitative approaches toward photocatalysis by design

    KAUST Repository

    Takanabe, Kazuhiro

    2017-10-11

    A widely used term, “photocatalysis”, generally addresses photocatalytic (energetically down-hill) and photosynthetic (energetically up-hill) reactions and refers to the use of photonic energy as a driving force for chemical transformations, i.e., electron reorganization to form/break chemical bonds. Although there are many such important reactions, this contribution focuses on the fundamental aspects of photocatalytic water splitting into hydrogen and oxygen by using light from the solar spectrum, which is one of the most investigated photosynthetic reactions. Photocatalytic water splitting using solar energy is considered to be artificial photosynthesis that produces a solar fuel because the reaction mimics nature’s photosynthesis not only in its redox reaction type but also in its thermodynamics (water splitting: 1.23 eV vs. glucose formation: 1.24 eV). To achieve efficient photocatalytic water splitting, all of the parameters, though involved at different timescales and spatial resolutions, should be optimized because the overall efficiency is obtained as the multiplication of all these fundamental efficiencies. The purpose of this review article is to provide the guidelines of a concept, “photocatalysis by design”, which is the opposite of “black box screening”; this concept refers to making quantitative descriptions of the associated physical and chemical properties to determine which events/parameters have the most impact on improving the overall photocatalytic performance, in contrast to arbitrarily ranking different photocatalyst materials. First, the properties that can be quantitatively measured or calculated are identified. Second, the quantities of these identified properties are determined by performing adequate measurements and/or calculations. Third, the obtained values of these properties are integrated into equations so that the kinetic/energetic bottlenecks of specific properties/processes can be determined, and the properties can

  13. Photocatalytic water splitting: Quantitative approaches toward photocatalysis by design

    KAUST Repository

    Takanabe, Kazuhiro

    2017-01-01

    A widely used term, “photocatalysis”, generally addresses photocatalytic (energetically down-hill) and photosynthetic (energetically up-hill) reactions and refers to the use of photonic energy as a driving force for chemical transformations, i.e., electron reorganization to form/break chemical bonds. Although there are many such important reactions, this contribution focuses on the fundamental aspects of photocatalytic water splitting into hydrogen and oxygen by using light from the solar spectrum, which is one of the most investigated photosynthetic reactions. Photocatalytic water splitting using solar energy is considered to be artificial photosynthesis that produces a solar fuel because the reaction mimics nature’s photosynthesis not only in its redox reaction type but also in its thermodynamics (water splitting: 1.23 eV vs. glucose formation: 1.24 eV). To achieve efficient photocatalytic water splitting, all of the parameters, though involved at different timescales and spatial resolutions, should be optimized because the overall efficiency is obtained as the multiplication of all these fundamental efficiencies. The purpose of this review article is to provide the guidelines of a concept, “photocatalysis by design”, which is the opposite of “black box screening”; this concept refers to making quantitative descriptions of the associated physical and chemical properties to determine which events/parameters have the most impact on improving the overall photocatalytic performance, in contrast to arbitrarily ranking different photocatalyst materials. First, the properties that can be quantitatively measured or calculated are identified. Second, the quantities of these identified properties are determined by performing adequate measurements and/or calculations. Third, the obtained values of these properties are integrated into equations so that the kinetic/energetic bottlenecks of specific properties/processes can be determined, and the properties can

  14. Formulation, evaluation and 3(2) full factorial design-based optimization of ondansetron hydrochloride incorporated taste masked microspheres.

    Science.gov (United States)

    Kharb, Vandana; Saharan, Vikas Anand; Dev, Kapil; Jadhav, Hemant; Purohit, Suresh

    2014-11-01

    Masking the bitter taste of Ondansetron hydrochloride (ONS) may improve palatability, acceptance and compliance of ONS products. ONS-loaded, taste-masked microspheres were prepared with a polycationic pH-sensitive polymer and 3(2) full factorial design (FFD) was applied to optimize microsphere batches. Solvent evaporation, in acetone--methanol/liquid paraffin system, was used to prepare taste-masked ONS microspheres. The effect of varying drug/polymer (D/P) ratios on microspheres characteristics were studied by 3(2) FFD. Desirability function was used to search the optimum formulation. Microspheres were evaluated by FTIR, XRD and DSC to examine interaction and effect of microencapsulation process. In vitro taste assessment approach based on bitterness threshold and drug release was used to assess bitterness scores. Prepared ONS microspheres were spherical and surface was wrinkled. ONS was molecularly dispersed in microspheres without any incompatibility with EE100. In hydrochloric acid buffer pH 1.2, ONS released completely from microsphere in just 10 min. Contrary to this, ONS release at initial 5 min from taste-masked microspheres was less than the bitterness threshold. Full factorial design and in vitro taste assessment approach, coupled together, was successfully applied to develop and optimize batches of ONS incorporated taste-masked microspheres.

  15. Product plots.

    Science.gov (United States)

    Wickham, Hadley; Hofmann, Heike

    2011-12-01

    We propose a new framework for visualising tables of counts, proportions and probabilities. We call our framework product plots, alluding to the computation of area as a product of height and width, and the statistical concept of generating a joint distribution from the product of conditional and marginal distributions. The framework, with extensions, is sufficient to encompass over 20 visualisations previously described in fields of statistical graphics and infovis, including bar charts, mosaic plots, treemaps, equal area plots and fluctuation diagrams. © 2011 IEEE

  16. SCALPLO, Plotting of Flux Output from SCALE Program

    International Nuclear Information System (INIS)

    Hersman, A.; De Leege, P.F.A.; Hoogenboom, J.E.

    1993-01-01

    1 - Description of program or function: SCALPLO is a plot program, designed to plot flux, power and spectrum information. Data exchange between SCALE modules and SCALPLO is via CCCC-interface files. As not all modules can produce these files, there are special routines supplied with SCALPLO that can produce CCCC-like files. These routines can be included in the code and for XSDRPM, CITATION, ANISN and DOT, the place to include these routines is supplied. 2 - Method of solution: SCALPLO consists of two sections. Firstly the pre-processor, which selects and reads the required data. Secondly the plot section which produces the plot on the selected output device. 3 - Restrictions on the complexity of the problem: SCALPLO requires DISSPLA version 11.0 or higher. The choice of output device depends on the devices installed

  17. Optimization of Emulsifying Effectiveness of Phytosterol in Milk Using Two-Level Fractional Factorial Design

    Directory of Open Access Journals (Sweden)

    He Yunxia

    2017-12-01

    Full Text Available In this paper emulsifying effects of seven emulsifiers including Tween 80, Span 80, tripolyglycerol monostearate, sodium stearoyl lactylate, sucrose ester, soy lecithin and monoglyceride on phytosterol in milk were investigated using single factor test and fractional factorial design. The addition for seven emulsifiers were in the following concentrations: 0.1%, 0.2%, 0.3%, 0.4%, 0.5% and 0.6%. The results revealed that tripolyglycerol monostearate, sucrose ester and monoglyceride had a significant emulsifying effect on phytosterol in milk, Tripolyglycerol monostearate showed a positive emulsifying effect on phytosterol in milk, while sucrose ester and monoglyceride exhibited a negative emulsifying effect on phytosterol in milk.

  18. Evaluation of the use of steelmaking slag as an aggregate in concrete mix: A factorial design approach

    OpenAIRE

    Aljbour Salah H.; Tarawneh Sultan A.; Al-Harahsheh Adnan M.

    2017-01-01

    Slag is investigated towards its potential use as an aggregate in concrete mix production. Full factorial design methodology is applied to study the effect of two process input variables, namely: slag as coarse aggregate and slag as medium aggregate on the properties of concrete mix. Additionally, the interaction between input variables is also examined. Incorporating steel slag aggregate in the concrete mix affected its compressive strength. Enhanced compressive strength concrete mix was obt...

  19. PRP: a FORTRAN IV interactive plotting program

    Science.gov (United States)

    Andrew, A. S.; Linde, J.

    A computer program, PRP, has been designed to plot any arithmetic combination selected from a set of major and trace element data on a y- x graph. y and x are defined and entered as a program string (y, x) which is interpreted sequentially. Operators ( +, -, ∗, /, ( unary) , square root, log 10, In c, antilog 10, exponential, integer, absolute value, (,),,) and integer or real numbers may be included. Axis lengths and scales are determined by the user. Five different plotting symbols are available.

  20. Statistical optimization of the growth factors for Chaetoceros neogracile using fractional factorial design and central composite design.

    Science.gov (United States)

    Jeong, Sung-Eun; Park, Jae-Kweon; Kim, Jeong-Dong; Chang, In-Jeong; Hong, Seong-Joo; Kang, Sung-Ho; Lee, Choul-Gyun

    2008-12-01

    Statistical experimental designs; involving (i) a fractional factorial design (FFD) and (ii) a central composite design (CCD) were applied to optimize the culture medium constituents for production of a unique antifreeze protein by the Antartic microalgae Chaetoceros neogracile. The results of the FFD suggested that NaCl, KCl, MgCl2, and Na2SiO3 were significant variables that highly influenced the growth rate and biomass production. The optimum culture medium for the production of an antifreeze protein from C. neogracile was found to be Kalleampersandrsquor;s artificial seawater, pH of 7.0ampersandplusmn;0.5, consisting of 28.566 g/l of NaCl, 3.887 g/l of MgCl2, 1.787 g/l of MgSO4, 1.308 g/l of CaSO4, 0.832 g/l of K2SO4, 0.124 g/l of CaCO3, 0.103 g/l of KBr, 0.0288 g/l of SrSO4, and 0.0282 g/l of H3BO3. The antifreeze activity significantly increased after cells were treated with cold shock (at -5oC) for 14 h. To the best of our knowledge, this is the first report demonstrating an antifreeze-like protein of C. neogracile.

  1. Process of chemical recycling of post-consumer PET using a factorial design

    International Nuclear Information System (INIS)

    Lacerda, Carlos Eduardo de O.; Almeida, Yeda Medeiros B. de; Vinhas, Gloria M.

    2015-01-01

    The present study investigated important variables in the depolymerization reaction of post-consumer poly (ethylene terephthalate) - PET via alkaline hydrolysis. Through this reaction is obtained terephthalic acid (PTA), a monomer, which when purified, is used for the production of PET resin. The study was based on a 2"2 factorial design in which the independent variables were the concentration of NaOH solution and the reaction time, and the dependent variable was the yield of PTA obtained. The experiments that generated the best results, 100 % of yield, were obtained with the higher values of the independent variables. Statistical analysis showed that the concentration of NaOH solution is the variable that most influences in the process. The PTA obtained was analyzed by NMR ¹H technique, confirming the strong resemblance to commercial PTA obtained by petrochemical way. (author)

  2. Tau-charm factory..

    Energy Technology Data Exchange (ETDEWEB)

    Anon.

    1995-10-15

    In addition to hearing the latest experimental and theoretical developments at the 17th International Symposium on Lepton Photon Interactions in Beijing, delegates were brought up-to-date on the substantial progress towards the realization of a Tau-Charm Factory in the Chinese capital. Opening the Symposium, Zhou Guangzhao, President of the Chinese Academy of Sciences, expressed a commitment of the Chinese government to basic research and its interest in the continuing development high energy physics in China. Following the very successful construction and operation of Beijing's Electron-Positron Collider, BEPC, the Chinese government has provided 5M yuan ($US 600,000) for a feasibility study by the end of 1996 for a Tau-Charm Factory at Beijing's Institute of High Energy Physics (IHEP). Professor Zhou expressed his belief that, once approved, such a factory would greatly enhance high energy physics in China. He warmly welcomed international collaboration both in the construction of the accelerator and in the experimental programme. His comments were reinforced in the following welcome speech by IHEP Director Zheng Zhipeng. Conference delegates had the opportunity to inspect the BEPC injector and collider, built almost entirely by Chinese industry. The International Committee for Future Accelerators (ICFA) met during the Symposium, with Tau- Charm Factory business on the agenda. In his subsequent report, ICFA Chairman John Peoples said that a Tau-Charm Factory provides a unique experimental environment for the precision studies of tau, charm and light quark-gluon spectroscopy, and that some issues in these fields are not satisfactorily addressed solely by B Factories or fixed-target experiments. The committee expressed a strong interest in seeing a Tau-Charm Factory built and noted the serious interest, especially in China, and looks forward to operation and exploitation by the international physics community. In their Beijing summary talks, both Sam Ting and T

  3. Tau-charm factory..

    International Nuclear Information System (INIS)

    Anon.

    1995-01-01

    In addition to hearing the latest experimental and theoretical developments at the 17th International Symposium on Lepton Photon Interactions in Beijing, delegates were brought up-to-date on the substantial progress towards the realization of a Tau-Charm Factory in the Chinese capital. Opening the Symposium, Zhou Guangzhao, President of the Chinese Academy of Sciences, expressed a commitment of the Chinese government to basic research and its interest in the continuing development high energy physics in China. Following the very successful construction and operation of Beijing's Electron-Positron Collider, BEPC, the Chinese government has provided 5M yuan ($US 600,000) for a feasibility study by the end of 1996 for a Tau-Charm Factory at Beijing's Institute of High Energy Physics (IHEP). Professor Zhou expressed his belief that, once approved, such a factory would greatly enhance high energy physics in China. He warmly welcomed international collaboration both in the construction of the accelerator and in the experimental programme. His comments were reinforced in the following welcome speech by IHEP Director Zheng Zhipeng. Conference delegates had the opportunity to inspect the BEPC injector and collider, built almost entirely by Chinese industry. The International Committee for Future Accelerators (ICFA) met during the Symposium, with Tau- Charm Factory business on the agenda. In his subsequent report, ICFA Chairman John Peoples said that a Tau-Charm Factory provides a unique experimental environment for the precision studies of tau, charm and light quark-gluon spectroscopy, and that some issues in these fields are not satisfactorily addressed solely by B Factories or fixed-target experiments. The committee expressed a strong interest in seeing a Tau-Charm Factory built and noted the serious interest, especially in China, and looks forward to operation and exploitation by the international physics community. In their Beijing summary talks, both Sam Ting

  4. Muon Acceleration: Neutrino Factory and Beyond

    Energy Technology Data Exchange (ETDEWEB)

    Bogacz, Alex [Thomas Jefferson National Accelerator Facility (TJNAF), Newport News, VA (United States)

    2018-03-01

    We summarize the current state of a concept for muon acceleration aimed at a future Neutrino Factory and extendable to Higgs Factory. The main thrust of these studies was to reduce the overall cost while maintaining performance by exploring the interplay between the complexity of the cooling systems and the acceptance of the accelerator complex. To ensure adequate survival for the short-lived muons, acceleration must occur at high average gradient. The need for large transverse and longitudinal acceptances drives the design of the acceleration system to an initially low RF frequency, e.g., 325 MHz, which is then increased to 650 MHz as the transverse size shrinks with increasing energy. High-gradient normal conducting RF cavities at these frequencies require extremely high peak-power RF sources. Hence superconducting RF (SRF) cavities are chosen. We consider an SRF-efficient design based on a multi-pass (4.5) ?dogbone? RLA, extendable to multi-pass FFAG-like arcs.

  5. Design and analysis of a wiggler magnet system for the PEP-II B-Factory LER

    International Nuclear Information System (INIS)

    Heim, J.; Kendall, M.; Bertolini, L.; Fackler, O.; O'Connor, T.; Swan, T.; Zholents, A.

    1996-01-01

    The Low Energy Ring (LER) of the PEP-II B-Factory will use a wiggler magnet system for emittance control and additional damping. The wiggler magnet system is a set of 11 individual iron core, water cooled, dipole magnets designed to operate at 1.6 T and generate 400 kW of synchrotron radiation. Space has been provided to add a second wiggler with an additional 400 kW of synchrotron radiation if more damping is needed in the future. A copper vacuum chamber is used with continuous antechambers connected to both sides of the beam chamber via slots. Synchrotron radiation dump surfaces and distributed vacuum pumping are located in both antechambers. The authors describe the design and analysis of the wiggler magnets and the salient features of the vacuum chamber and dumps

  6. Permanently split capacitor motor-study of the design parameters

    Science.gov (United States)

    Sarac, Vasilija; Stefanov, Goce

    2017-09-01

    Paper analyzes the influence of various design parameters on torque of permanently split capacitor motor. Motor analytical model is derived and it is used for calculating the performance characteristics of basic motor model. The acquired analytical model is applied in optimization software that uses genetic algorithms (GA) as an optimization method. Optimized motor model with increased torque is derived by varying three motor parameters in GA program: winding turns ratio, average air gap flux density and motor stack length. Increase of torque has been achieved for nominal operation but also at motor starting. Accuracy of the derived models is verified by Simulink. The acquired values of several motor parameters from transient characteristics of Simulink models are compared with the corresponding values obtained from analytical models of both motors, basic and optimized. Numerical analysis, based on finite element method (FEM), is also performed for both motor models. As a result of the FEM analysis, magnetic flux density in motor cross-section is calculated and adequate conclusions are derived in relation to core saturation and air gap flux density in both motor models.

  7. Plot 3

    DEFF Research Database (Denmark)

    Lund, Inger-Lise; Gjessing, Susanne; Hermansen, Anne-Mette

    Plot 3 er første udgivelse af et alsidigt dansksystem til mellemtrinnet, hvor digitale medier er integreret i den daglige undervisning.......Plot 3 er første udgivelse af et alsidigt dansksystem til mellemtrinnet, hvor digitale medier er integreret i den daglige undervisning....

  8. The Effect of Irrigation Regimes and Mulch Application on Vegetative Indices and Essential Oil Content of Peppermint (Mentha piperita L.

    Directory of Open Access Journals (Sweden)

    M. Azizi

    2016-02-01

    Full Text Available Peppermint (Mentha piperita L. from Lamiaceae family is one of the most important medicinal plants, used in food, sanitary and cosmetic industries. A field experiment was carried out in Ferdowsi University of Mashhad in 2010-2011 to evaluate the effects of three irrigation levels (100, 80 and 60 percent of water requirements calculated by evaporation pan class A and two mulch types (black plastic and wood chips in comparison to control (without mulch on physiological parameter and essential oils content in a factorial experiments on the basis of Randimised Complete Block Desing with four replications. The data obtained from each harvest analyzed as a factorial experiment on the basis of randomized complete block design with four replications and the results of two harvests analyzed as split plot on time. The results of two harvest indicated that peppermint plants grow better in the first harvest than the second harvest. Plants collected in the first harvest showed higher dry matter and essential oil yield. The highest dry herb yield (44.12 g/plant, the highest percentage of essential oil (2.835 %v/w and the highest essential oil yield (116.7 l/ha detected in plots treated with third level of irrigation and use of wood chips mulch. In conclusion the results also confirmed that the highest dry herb and the highest oil yield per area unit were observed in plots treated with third level of irrigation with use of wood chips mulch.

  9. SplitDist—Calculating Split-Distances for Sets of Trees

    DEFF Research Database (Denmark)

    Mailund, T

    2004-01-01

    We present a tool for comparing a set of input trees, calculating for each pair of trees the split-distances, i.e., the number of splits in one tree not present in the other.......We present a tool for comparing a set of input trees, calculating for each pair of trees the split-distances, i.e., the number of splits in one tree not present in the other....

  10. User manual for two simple postscript output FORTRAN plotting routines

    Science.gov (United States)

    Nguyen, T. X.

    1991-01-01

    Graphics is one of the important tools in engineering analysis and design. However, plotting routines that generate output on high quality laser printers normally come in graphics packages, which tend to be expensive and system dependent. These factors become important for small computer systems or desktop computers, especially when only some form of a simple plotting routine is sufficient. With the Postscript language becoming popular, there are more and more Postscript laser printers now available. Simple, versatile, low cost plotting routines that can generate output on high quality laser printers are needed and standard FORTRAN language plotting routines using output in Postscript language seems logical. The purpose here is to explain two simple FORTRAN plotting routines that generate output in Postscript language.

  11. The Half-Half Plot

    NARCIS (Netherlands)

    Einmahl, J.H.J.; Gantner, M.

    2009-01-01

    The Half-Half (HH) plot is a new graphical method to investigate qualitatively the shape of a regression curve. The empirical HH-plot counts observations in the lower and upper quarter of a strip that moves horizontally over the scatter plot. The plot displays jumps clearly and reveals further

  12. Analyzing the shape parameter effects on the performance of the mixed-flow fan using CFD and Factorial design

    International Nuclear Information System (INIS)

    Jung, Uk Hee; Kim, Joon Hyung; Kim, Sung; Kim, Jin Hyuk; Choi, Young Seok

    2016-01-01

    Fans are representative turbo-machinery widely used for ventilation throughout the industrial world. Recently, as the importance of energy saving has been magnified with the fans, the demand for the fans with high efficiency and performance has been increasing. The representative method for enhancing the performance includes design optimization; in practice, fan performance can be improved by changing the shape parameters such as those of meridional plane, impeller, and diffuser. Before optimizing the efficient design, a process of screening to select important design parameters is essential. The present study aimed to analyze the effects of mixed-flow fans' shape parameters on fan performance (static pressure and fan static efficiency) and derive optimum models based on the results. In this study, the shape parameters considered in the impeller domain are as follows: tip clearance, number of blades, beta angle of Leading edge (LE) in the blade, and beta angle of Trailing edge (TE) in the blade. The shape parameters considered in the diffuser domain are as follows: meridional length of the Guide vane (GV), number of GV, beta angle of LE in the GV and beta angle of TE in the GV. The effects of individual shape parameters were analyzed using the CFD (Computational fluid dynamic) and DOE (Design of experiments) methods. The reliability of CFD was verified through the comparison between preliminary fan model's experiment results and CFD results, and screening processes were implemented through 24-1 fractional factorial design. From the analysis of DOE results, it could be seen that the tip clearance and the number of blades in the impeller domain greatly affected the fan performance, and the beta angle of TE at the GV in the diffuser domain greatly affected the fan performance. Finally, the optimum models with improved fan performance were created using linear regression equations derived from 24-1 fractional factorial design.

  13. Computer experimental analysis of the CHP performance of a 100 kW e SOFC Field Unit by a factorial design

    Science.gov (United States)

    Calì, M.; Santarelli, M. G. L.; Leone, P.

    Gas Turbine Technologies (GTT) and Politecnico di Torino, both located in Torino (Italy), have been involved in the design and installation of a SOFC laboratory in order to analyse the operation, in cogenerative configuration, of the CHP 100 kW e SOFC Field Unit, built by Siemens-Westinghouse Power Corporation (SWPC), which is at present (May 2005) starting its operation and which will supply electric and thermal power to the GTT factory. In order to take the better advantage from the analysis of the on-site operation, and especially to correctly design the scheduled experimental tests on the system, we developed a mathematical model and run a simulated experimental campaign, applying a rigorous statistical approach to the analysis of the results. The aim of this work is the computer experimental analysis, through a statistical methodology (2 k factorial experiments), of the CHP 100 performance. First, the mathematical model has been calibrated with the results acquired during the first CHP100 demonstration at EDB/ELSAM in Westerwoort. After, the simulated tests have been performed in the form of computer experimental session, and the measurement uncertainties have been simulated with perturbation imposed to the model independent variables. The statistical methodology used for the computer experimental analysis is the factorial design (Yates' Technique): using the ANOVA technique the effect of the main independent variables (air utilization factor U ox, fuel utilization factor U F, internal fuel and air preheating and anodic recycling flow rate) has been investigated in a rigorous manner. Analysis accounts for the effects of parameters on stack electric power, thermal recovered power, single cell voltage, cell operative temperature, consumed fuel flow and steam to carbon ratio. Each main effect and interaction effect of parameters is shown with particular attention on generated electric power and stack heat recovered.

  14. KEKB B-Factory, the luminosity frontier

    International Nuclear Information System (INIS)

    Oide, Katsunobu

    2009-01-01

    The experiment at the KEKB B-Factory, as well as PEP-II, brought the final blow on the 2008 Nobel Prize in Physics for the Kobayashi-Maskawa theory. A few key issues will be described on the design and performance of KEKB to make the world's highest luminosity possible. (author)

  15. Preparation of one-step NiO/Ni-CGO composites using factorial design

    International Nuclear Information System (INIS)

    Araujo, A.J.M. de; Sousa, A R.O. de; Camposa, L.F.A.; Macedo, D.A.; Loureiro, F. J.A.; Fagg, D.P.

    2016-01-01

    This work deals with the synthesis, processing and characterization of NiO/Ni- CGO composite materials as potential solid oxide fuel cell (SOFC) anodes. The particulate materials were obtained by a one-step synthesis method and characterized by thermal analysis (prior to calcination) and X-ray diffraction (calcined powder). The ceramic processing of samples containing from 30 to 70 wt.% NiO was carried out by factorial design. Besides the NiO content controlled during the chemical synthesis, the impacts of the pore-former content (citric acid, used in proportions of 0, 7.5 and 15 wt.%) and the sintering temperature (1300, 1350 and 1400 °C) were also investigated. The open porosity of NiO-CGO composites and reduced Ni-CGO cermets was modeled as a function of factors (NiO content, citric acid content and sintering temperature) and interaction of factors. (author)

  16. Sample preparation and electrochemical data of Co3O4 working electrode for seawater splitting

    Directory of Open Access Journals (Sweden)

    Malkeshkumar Patel

    2017-10-01

    Full Text Available In this data article, we presented the electrochemical data of the working electrode made of Co3O4 semi-transparent film. Electrochemically stable, porous nature of Kirkendall-diffusion grown Co3O4 films were applied to generate hydrogen from the seawater splitting (Patel et al., 2017 [1]. The data presented in this article includes the photograph of prepared samples, polarization curves for water oxidation and Tafel plot, linear sweep voltammetry measurements under the pulsed light condition in 0.1 M Na2S2O3 electrolyte, and transient photoresponses with natural sea water. Moreover, seawater splitting using the Co3O4 working electrode is demonstrated.

  17. An asymmetric B-meson factory at PEP

    International Nuclear Information System (INIS)

    Garren, A.; Chattopadhyay, S.; Chin, Y.; Oddone, P.; Zisman, M.S.; Donald, M.; Feldman, G.; Paterson, J.M.; Rees, J.

    1989-03-01

    A preliminary design for a B-factory has been made using asymmetric collisions between positrons in the PEP storage ring and electrons in a new, log-energy ring. The design utilizes small-aperture, permanent-magnet quadrupoles close to the interaction point (IP). Optimization of optical and beam parameters at the IP will be discussed, as well as the lattice design of the interaction region and of the rings. 7 refs., 3 figs., 2 tabs

  18. A Generalization of the Alias Matrix

    DEFF Research Database (Denmark)

    Kulahci, Murat; Bisgaard, S.

    2006-01-01

    The investigation of aliases or biases is important for the interpretation of the results from factorial experiments. For two-level fractional factorials this can be facilitated through their group structure. For more general arrays the alias matrix can be used. This tool is traditionally based...... on the assumption that the error structure is that associated with ordinary least squares. For situations where that is not the case, we provide in this article a generalization of the alias matrix applicable under the generalized least squares assumptions. We also show that for the special case of split plot error...... structure, the generalized alias matrix simplifies to the ordinary alias matrix....

  19. Conditional Toxin Splicing Using a Split Intein System.

    Science.gov (United States)

    Alford, Spencer C; O'Sullivan, Connor; Howard, Perry L

    2017-01-01

    Protein toxin splicing mediated by split inteins can be used as a strategy for conditional cell ablation. The approach requires artificial fragmentation of a potent protein toxin and tethering each toxin fragment to a split intein fragment. The toxin-intein fragments are, in turn, fused to dimerization domains, such that addition of a dimerizing agent reconstitutes the split intein. These chimeric toxin-intein fusions remain nontoxic until the dimerizer is added, resulting in activation of intein splicing and ligation of toxin fragments to form an active toxin. Considerations for the engineering and implementation of conditional toxin splicing (CTS) systems include: choice of toxin split site, split site (extein) chemistry, and temperature sensitivity. The following method outlines design criteria and implementation notes for CTS using a previously engineered system for splicing a toxin called sarcin, as well as for developing alternative CTS systems.

  20. The introduction of radiation monitor produced by several nuclear instrument factories

    International Nuclear Information System (INIS)

    Yu Liying

    2005-01-01

    The paper introduce some radiation monitor products of several nuclear instrument factories include Xi'an Nuclear Instrument Factory, MGP Instruments Inc, and Canberra Industries Inc. The introduction aspects include the range, configuration, and application of products. So, the paper is reference for the designer with responsibility for radiation monitoring system of new nuclear project. (authors)

  1. SYSTEMS BIOLOGY AND METABOLIC ENGINEERING OF ARTHROSPIRA CELL FACTORIES

    Directory of Open Access Journals (Sweden)

    Amornpan Klanchui

    2012-10-01

    Full Text Available Arthrospira are attractive candidates to serve as cell factories for production of many valuable compounds useful for food, feed, fuel and pharmaceutical industries. In connection with the development of sustainable bioprocessing, it is a challenge to design and develop efficient Arthrospira cell factories which can certify effective conversion from the raw materials (i.e. CO2 and sun light into desired products. With the current availability of the genome sequences and metabolic models of Arthrospira, the development of Arthrospira factories can now be accelerated by means of systems biology and the metabolic engineering approach. Here, we review recent research involving the use of Arthrospira cell factories for industrial applications, as well as the exploitation of systems biology and the metabolic engineering approach for studying Arthrospira. The current status of genomics and proteomics through the development of the genome-scale metabolic model of Arthrospira, as well as the use of mathematical modeling to simulate the phenotypes resulting from the different metabolic engineering strategies are discussed. At the end, the perspective and future direction on Arthrospira cell factories for industrial biotechnology are presented.

  2. Sample size requirements for separating out the effects of combination treatments: randomised controlled trials of combination therapy vs. standard treatment compared to factorial designs for patients with tuberculous meningitis.

    Science.gov (United States)

    Wolbers, Marcel; Heemskerk, Dorothee; Chau, Tran Thi Hong; Yen, Nguyen Thi Bich; Caws, Maxine; Farrar, Jeremy; Day, Jeremy

    2011-02-02

    In certain diseases clinical experts may judge that the intervention with the best prospects is the addition of two treatments to the standard of care. This can either be tested with a simple randomized trial of combination versus standard treatment or with a 2 x 2 factorial design. We compared the two approaches using the design of a new trial in tuberculous meningitis as an example. In that trial the combination of 2 drugs added to standard treatment is assumed to reduce the hazard of death by 30% and the sample size of the combination trial to achieve 80% power is 750 patients. We calculated the power of corresponding factorial designs with one- to sixteen-fold the sample size of the combination trial depending on the contribution of each individual drug to the combination treatment effect and the strength of an interaction between the two. In the absence of an interaction, an eight-fold increase in sample size for the factorial design as compared to the combination trial is required to get 80% power to jointly detect effects of both drugs if the contribution of the less potent treatment to the total effect is at least 35%. An eight-fold sample size increase also provides a power of 76% to detect a qualitative interaction at the one-sided 10% significance level if the individual effects of both drugs are equal. Factorial designs with a lower sample size have a high chance to be underpowered, to show significance of only one drug even if both are equally effective, and to miss important interactions. Pragmatic combination trials of multiple interventions versus standard therapy are valuable in diseases with a limited patient pool if all interventions test the same treatment concept, it is considered likely that either both or none of the individual interventions are effective, and only moderate drug interactions are suspected. An adequately powered 2 x 2 factorial design to detect effects of individual drugs would require at least 8-fold the sample size of the

  3. Application of full factorial design to study the tribological properties of AA6061-B4C and AA6061-B4C-MoS2 composites

    Directory of Open Access Journals (Sweden)

    Monikandan V. V.

    2018-03-01

    Full Text Available This study statistically analyzes the tribological properties of AA6061-10 wt. % B4C mono composite and AA6061-10 wt.% B4C-7.5 wt. % MoS2 hybrid composite. The tribological behavior of the composites was studied at atmospheric conditions using a pin-on-disk tribo-tester. The tribological experiments were conducted as per the full factorial design (FFD experimental scheme. The ANOVA analysis of the wear rate revealed that the three factors, A (MoS2 particles addition, B (applied load, and D (sliding distance presented the physical and statistical significance on the wear rate. The ANOVA analysis of the friction coefficient revealed that the factors B (applied load and C (sliding speed and interaction AB (interaction of MoS2 particles addition and applied load presented the physical and statistical significance on the friction coefficient. It is observed from the main effects plots of the wear rate and friction coefficient that the increase in the levels of factors B (applied load and D (sliding distance increased the wear rate and friction coefficient. However, the wear rate and friction coefficient decreased with the increase in the level of factor A (MoS2 particles addition.

  4. Development and Validation of HPLC-DAD and UHPLC-DAD Methods for the Simultaneous Determination of Guanylhydrazone Derivatives Employing a Factorial Design.

    Science.gov (United States)

    Azevedo de Brito, Wanessa; Gomes Dantas, Monique; Andrade Nogueira, Fernando Henrique; Ferreira da Silva-Júnior, Edeildo; Xavier de Araújo-Júnior, João; Aquino, Thiago Mendonça de; Adélia Nogueira Ribeiro, Êurica; da Silva Solon, Lilian Grace; Soares Aragão, Cícero Flávio; Barreto Gomes, Ana Paula

    2017-08-30

    Guanylhydrazones are molecules with great pharmacological potential in various therapeutic areas, including antitumoral activity. Factorial design is an excellent tool in the optimization of a chromatographic method, because it is possible quickly change factors such as temperature, mobile phase composition, mobile phase pH, column length, among others to establish the optimal conditions of analysis. The aim of the present work was to develop and validate a HPLC and UHPLC methods for the simultaneous determination of guanylhydrazones with anticancer activity employing experimental design. Precise, exact, linear and robust HPLC and UHPLC methods were developed and validated for the simultaneous quantification of the guanylhydrazones LQM10, LQM14, and LQM17. The UHPLC method was more economic, with a four times less solvent consumption, and 20 times less injection volume, what allowed better column performance. Comparing the empirical approach employed in the HPLC method development to the DoE approach employed in the UHPLC method development, we can conclude that the factorial design made the method development faster, more practical and rational. This resulted in methods that can be employed in the analysis, evaluation and quality control of these new synthetic guanylhydrazones.

  5. Design and Construction of a High-speed Network Connecting All the Protein Crystallography Beamlines at the Photon Factory

    International Nuclear Information System (INIS)

    Matsugaki, Naohiro; Yamada, Yusuke; Igarashi, Noriyuki; Wakatsuki, Soichi

    2007-01-01

    A private network, physically separated from the facility network, was designed and constructed which covered all the four protein crystallography beamlines at the Photon Factory (PF) and Structural Biology Research Center (SBRC). Connecting all the beamlines in the same network allows for simple authentication and a common working environment for a user who uses multiple beamlines. Giga-bit Ethernet wire-speed was achieved for the communication among the beamlines and SBRC buildings

  6. Relationship between mandibular anatomy and the occurrence of a bad split upon sagittal split osteotomy.

    Science.gov (United States)

    Aarabi, Mohammadali; Tabrizi, Reza; Hekmat, Mina; Shahidi, Shoaleh; Puzesh, Ayatollah

    2014-12-01

    A bad split is a troublesome complication of the sagittal split osteotomy (SSO). The aim of this study was to evaluate the relation between the occurrence of a bad split and mandibular anatomy in SSO using cone-beam computed tomography. The authors designed a cohort retrospective study. Forty-eight patients (96 SSO sites) were studied. The buccolingual thickness of the retromandibular area (BLR), the buccolingual thickness of the ramus at the level of the lingula (BLTR), the height of the mandible from the alveolar crest to the inferior border of the mandible, (ACIB), the distance between the sigmoid notch and the inferior border of the mandible (SIBM), and the anteroposterior width of the ramus (APWR) were measured. The independent t test was applied to compare anatomic measurements between the group with and the group without bad splits. The receiver operating characteristic (ROC) test was used to find a cutoff point in anatomic size for various parts of the mandible related to the occurrence of bad splits. The mean SIBM was 47.05±6.33 mm in group 1 (with bad splits) versus 40.66±2.44 mm in group 2 (without bad splits; P=.01). The mean BLTR was 5.74±1.11 mm in group 1 versus 3.19±0.55 mm in group 2 (P=.04). The mean BLR was 14.98±2.78 mm in group 1 versus 11.21±1.29 mm in group 2 (P=.001). No statistically significant difference was found for APWR and ACIB between the 2 groups. The ROC test showed cutoff points of 10.17 mm for BLR, 36.69 mm for SIBM, and 4.06 mm for BLTR. This study showed that certain mandibular anatomic differences can increase the risk of a bad split during SSO surgery. Copyright © 2014 American Association of Oral and Maxillofacial Surgeons. Published by Elsevier Inc. All rights reserved.

  7. SplitRacer - a new Semi-Automatic Tool to Quantify And Interpret Teleseismic Shear-Wave Splitting

    Science.gov (United States)

    Reiss, M. C.; Rumpker, G.

    2017-12-01

    We have developed a semi-automatic, MATLAB-based GUI to combine standard seismological tasks such as the analysis and interpretation of teleseismic shear-wave splitting. Shear-wave splitting analysis is widely used to infer seismic anisotropy, which can be interpreted in terms of lattice-preferred orientation of mantle minerals, shape-preferred orientation caused by fluid-filled cracks or alternating layers. Seismic anisotropy provides a unique link between directly observable surface structures and the more elusive dynamic processes in the mantle below. Thus, resolving the seismic anisotropy of the lithosphere/asthenosphere is of particular importance for geodynamic modeling and interpretations. The increasing number of seismic stations from temporary experiments and permanent installations creates a new basis for comprehensive studies of seismic anisotropy world-wide. However, the increasingly large data sets pose new challenges for the rapid and reliably analysis of teleseismic waveforms and for the interpretation of the measurements. Well-established routines and programs are available but are often impractical for analyzing large data sets from hundreds of stations. Additionally, shear wave splitting results are seldom evaluated using the same well-defined quality criteria which may complicate comparison with results from different studies. SplitRacer has been designed to overcome these challenges by incorporation of the following processing steps: i) downloading of waveform data from multiple stations in mseed-format using FDSNWS tools; ii) automated initial screening and categorizing of XKS-waveforms using a pre-set SNR-threshold; iii) particle-motion analysis of selected phases at longer periods to detect and correct for sensor misalignment; iv) splitting analysis of selected phases based on transverse-energy minimization for multiple, randomly-selected, relevant time windows; v) one and two-layer joint-splitting analysis for all phases at one station by

  8. Cell factories for a sustainable world

    DEFF Research Database (Denmark)

    Kindtler, Jens William

    2016-01-01

    The Novo Nordisk Foundation Center for Biosustainability (CFB) is a university research center under the Technical University of Denmark within the field of design, engineering and construction of superior cell factories for the production of biopharmaceuticals, anti-infective compounds, industrial......-spectrum inhibitors against multi-drug resistant (MDR) Gram-negative bacterial pathogens using co-Adaptive Laboratory Evolution, 3. Design and engineering of E. coli and Saccharomyces cerevisiae for biobased production of various classes of chemicals. CFB has 230 employees....

  9. Effect of splitting a mixed-model line on shortening the line length under open- and closed-boundary working area settings

    Science.gov (United States)

    Zhang, Donghao; Matsuura, Haruki; Asada, Akiko

    2017-04-01

    Some automobile factories have segmented mixed-model production lines into shorter sub-lines according to part group, such as engine, trim, and powertrain. The effects of splitting a line into sub-lines have been reported from the standpoints of worker motivation, productivity improvement, and autonomy based on risk spreading. There has been no mention of the possibility of shortening the line length by altering the product sequence using sub-lines. The purpose of the present paper is to determine the conditions under which sub-lines reduce the line length and the degree to which the line length may be shortened. The line lengths for a non-split line and a line that has been split into sub-lines are compared using three methods for determining the working area, the standard closed boundary, the optimized open boundary, and real-life constant-length stations. The results are discussed by analyzing the upper and lower bounds of the line length. Based on these results, a procedure for deciding whether or not to split a production line is proposed.

  10. Comparison of Three Plot Selection Methods for Estimating Change in Temporally Variable, Spatially Clustered Populations.

    Energy Technology Data Exchange (ETDEWEB)

    Thompson, William L. [Bonneville Power Administration, Portland, OR (US). Environment, Fish and Wildlife

    2001-07-01

    Monitoring population numbers is important for assessing trends and meeting various legislative mandates. However, sampling across time introduces a temporal aspect to survey design in addition to the spatial one. For instance, a sample that is initially representative may lose this attribute if there is a shift in numbers and/or spatial distribution in the underlying population that is not reflected in later sampled plots. Plot selection methods that account for this temporal variability will produce the best trend estimates. Consequently, I used simulation to compare bias and relative precision of estimates of population change among stratified and unstratified sampling designs based on permanent, temporary, and partial replacement plots under varying levels of spatial clustering, density, and temporal shifting of populations. Permanent plots produced more precise estimates of change than temporary plots across all factors. Further, permanent plots performed better than partial replacement plots except for high density (5 and 10 individuals per plot) and 25% - 50% shifts in the population. Stratified designs always produced less precise estimates of population change for all three plot selection methods, and often produced biased change estimates and greatly inflated variance estimates under sampling with partial replacement. Hence, stratification that remains fixed across time should be avoided when monitoring populations that are likely to exhibit large changes in numbers and/or spatial distribution during the study period. Key words: bias; change estimation; monitoring; permanent plots; relative precision; sampling with partial replacement; temporary plots.

  11. The Idea Factory: An Interactive Intergroup Exercise

    Science.gov (United States)

    Rosh, Lisa; Leach, Evan

    2011-01-01

    This article outlines the Idea Factory exercise, an interactive exercise designed to help participants examine group, individual, and organizational factors that affect intergroup conflict. Specific emphasis is placed on exploring the relationship between intra- and intergroup dynamics and identifying managerial practices that foster effective…

  12. Effects of Cycocel and Nitrogen Application on Yield and Yield Components of Autumn-Grown Oilseed Rape at Different Plant Densities

    Directory of Open Access Journals (Sweden)

    S. Majd

    2013-06-01

    Full Text Available In this research, which was carried out as two experiments (in the field and greenhouse at Research Farm of College of Agriculture, Shiraz University, Shiraz, Iran, in 2009-2010 growing season, the effects of different levels of nitrogen, plant density and cycocel application on yield and yield components of autumn-grown oilseed rape (Talaye cultivar were investigated. The field experiment was designed as split-split plot based on completely randomized blocks design. Treatments included nitrogen level (80, 140, 200 and 260 kg/ha as the main plot, plant density (70 and 90 plants/m2 as sub-plot and cycocel rate (0, 1.4 and 2.8 L/ha as sub- subplot. The greenhouse experiment, which was arranged as a factorial based on complete randomized design, included nitrogen level (0, 50, 100, 150 and 200 kg/ha and cycocel rate (0, 1.4 and 2.8 L/ha. Results showed that the highest seed yield was achieved at 200 kg N/ha, 2.8 L/ha cycocel and plant density of 90 plants/m2 (533.17, 533.96 and 521.6 g/m2, respectively. Application of 2.8 L/ha cycocel was associated with increased number of siliques per plant and final plants dry weight. Increasing plant density from 70 to 90 plants/m2 was associated with decreased number of siliques per plant, plant dry weight and number of seeds per silique. It appears that application of 200 kg N/ha, 2.8 L/ha cycocel and plant density of 90 plants/m2 could be recommended for maximum grain yield of autumn-grown rapeseed cv. Talaye, in agroclimatic conditions similar to this research

  13. PLOTTAB, Curve and Point Plotting with Error Bars

    International Nuclear Information System (INIS)

    1999-01-01

    1 - Description of program or function: PLOTTAB is designed to plot any combination of continuous curves and/or discrete points (with associated error bars) using user supplied titles and X and Y axis labels and units. If curves are plotted, the first curve may be used as a standard; the data and the ratio of the data to the standard will be plotted. 2 - Method of solution: PLOTTAB: The program has no idea of what data is being plotted and yet by supplying titles, X and Y axis labels and units the user can produce any number of plots with each plot containing almost any combination of curves and points with each plot properly identified. In order to define a continuous curve between tabulated points, this program must know how to interpolate between points. By input the user may specify either the default option of linear x versus linear y interpolation or alternatively log x and/or log Y interpolation. In all cases, regardless of the interpolation specified, the program will always interpolate the data to the plane of the plot (linear or log x and y plane) in order to present the true variation of the data between tabulated points, based on the user specified interpolation law. Tabulated points should be tabulated at a sufficient number of x values to insure that the difference between the specified interpolation and the 'true' variation of a curve between tabulated values is relatively small. 3 - Restrictions on the complexity of the problem: A combination of up to 30 curves and sets of discrete points may appear on each plot. If the user wishes to use this program to compare different sets of data, all of the data must be in the same units

  14. Optimization Of Freeze-Dried Starter For Yogurt By Full Factorial Experimental Design

    Directory of Open Access Journals (Sweden)

    Chen He

    2015-12-01

    Full Text Available With the rapidly development of fermented milk product, it is significant for enhancing the performance of starter culture. This paper not only investigated the influence of anti-freeze factors and freeze-drying protective agents on viable count, freeze-drying survival rate and yield of Lactobacillus bulgaricus (LB and Streptococcus thermophilus (ST, but also optimized the bacteria proportion of freeze-dried starter culture for yogurt by full factorial experimental design. The results showed as following: the freeze-drying protective agents or anti-freeze factors could enhanced survival rate of LB and ST; the freeze-dried LB and ST powders containing both of anti-freeze factors and freeze-drying protective agents had higher viable count and freeze-drying survival rate that were 84.7% and 79.7% respectively; In terms of fermentation performance, the best group of freeze-dried starter for yogurt was the compound of LB3 and ST2.

  15. A factory concept for processing and manufacturing with lunar material

    Science.gov (United States)

    Driggers, G. W.

    1977-01-01

    A conceptual design for an orbital factory sized to process 1.5 million metric tons per year of raw lunar fines into 0.3 million metric tons of manufacturing materials is presented. A conservative approach involving application of present earth-based technology leads to a design devoid of new inventions. Earth based counterparts to the factory machinery were used to generate subsystem masses and lumped parameters for volume and mass estimates. The results are considered to be conservative since technologies more advanced than those assumed are presently available in many areas. Some attributes of potential space processing technologies applied to material refinement and component manufacture are discussed.

  16. Computer modelling of bunch-by-bunch feedback for the SLAC B-factory design

    International Nuclear Information System (INIS)

    Briggs, D.; Fox, J.D.; Hosseini, W.; Klaisner, L.; Morton, P.; Pellegrin, J.L.; Thompson, K.A.; Lambertson, G.

    1991-05-01

    The SLAC B-factory design, with over 1600 high current bunches circulating in each ring, will require a feedback system to avoid coupled-bunch instabilities. A computer model of the storage ring, including the RF system, wave fields, synchrotron radiation loss, and the bunch-by-bunch feedback system is presented. The feedback system model represents the performance of a fast phase detector front end (including system noise and imperfections), a digital filter used to generate a correction voltage, and a power amplifier and beam kicker system. The combined ring-feedback system model is used to study the feedback system performance required to suppress instabilities and to quantify the dynamics of the system. Results are presented which show the time development of coupled bunch instabilities and the damping action of the feedback system. 3 refs., 5 figs., 2 tabs

  17. Multivariate study of parameters in the determination of pesticide residues in apple by headspace solid phase microextraction coupled to gas chromatography-mass spectrometry using experimental factorial design.

    Science.gov (United States)

    Abdulra'uf, Lukman Bola; Tan, Guan Huat

    2013-12-15

    Solid-phase microextraction (SPME) is a solvent-less sample preparation method which combines sample preparation, isolation, concentration and enrichment into one step. In this study, multivariate strategy was used to determine the significance of the factors affecting the solid phase microextraction of pesticide residues (fenobucarb, diazinon, chlorothalonil and chlorpyrifos) using a randomised factorial design. The interactions and effects of temperature, time and salt addition on the efficiency of the extraction of the pesticide residues were evaluated using 2(3) factorial designs. The analytes were extracted with 100 μm PDMS fibres according to the factorial design matrix and desorbed into a gas chromatography-mass spectrometry detector. The developed method was applied for the analysis of apple samples and the limits of detection were between 0.01 and 0.2 μg kg(-)(1), which were lower than the MRLs for apples. The relative standard deviations (RSD) were between 0.1% and 13.37% with average recovery of 80-105%. The linearity ranges from 0.5-50 μg kg(-)(1) with correlation coefficient greater than 0.99. Copyright © 2013 Elsevier Ltd. All rights reserved.

  18. The tau-charm factory: Experimental perspectives

    International Nuclear Information System (INIS)

    Perl, M.L.; Schindler, R.H.

    1991-09-01

    This report discusses the Tau-Charm Factory Concept; D and D S Physics at the Tau-Charm Factory; τ and ν τ Physics at the Tau-Charm Factory; and Charmonium, Gluonium and Light Quark Spectroscopy at the Tau-Charm Factory

  19. The Factory of the Future, Group Exhibition

    OpenAIRE

    Dean, Lionel T.

    2016-01-01

    3D Printing, The factory of the future, Lieu du Design (centre for Design), Paris This exhibition dedicated entirely to 3D printing technology was billed as “the first in France wholly devoted to exploring the interdisciplinary and multifaceted topic of 3D printing technology and its undeniable influence on everything from industry, to economics, to creative and social issues, demonstrated to the public through achievements in the fields of 3D design, 3D printed architecture, 3D printed fa...

  20. The effect of different tillage and cover crops on soil quality

    DEFF Research Database (Denmark)

    Abdollahi, Lotfollah; Munkholm, Lars Juhl

    This paper examines the effect of different tillage treatments and cover crop on soil physical, chemical and biological properties of a sandy loam soil in a long-term field trial set up in 2007 at Foulum, Denmark. The experimental design is a split plot design with different tillage practices (di...... that P improved soil quality compared to H and D, especially when combined with cover crop. We also conclude that D may benefit from cover crop to yield better soil friability and hence soil quality.......This paper examines the effect of different tillage treatments and cover crop on soil physical, chemical and biological properties of a sandy loam soil in a long-term field trial set up in 2007 at Foulum, Denmark. The experimental design is a split plot design with different tillage practices...... (direct drilling (D), harrowing (H) to a depth of 8 cm and ploughing to a depth of 20 cm (P)) as main plot. The soil was cropped with cover crop (+CC) or left without cover crop (-CC) as split plot treatments in the main plots with different tillage treatments. We assessed topsoil structural quality...

  1. Investigation of the impact of trace elements on anaerobic volatile fatty acid degradation using a fractional factorial experimental design.

    Science.gov (United States)

    Jiang, Ying; Zhang, Yue; Banks, Charles; Heaven, Sonia; Longhurst, Philip

    2017-11-15

    The requirement of trace elements (TE) in anaerobic digestion process is widely documented. However, little is understood regarding the specific requirement of elements and their critical concentrations under different operating conditions such as substrate characterisation and temperature. In this study, a flask batch trial using fractional factorial design is conducted to investigate volatile fatty acids (VFA) anaerobic degradation rate under the influence of the individual and combined effect of six TEs (Co, Ni, Mo, Se, Fe and W). The experiment inoculated with food waste digestate, spiked with sodium acetate and sodium propionate both to 10 g/l. This is followed by the addition of a selection of the six elements in accordance with a 2 6-2 fractional factorial principle. The experiment is conducted in duplicate and the degradation of VFA is regularly monitored. Factorial effect analysis on the experimental results reveals that within these experimental conditions, Se has a key role in promoting the degradation rates of both acetic and propionic acids; Mo and Co are found to have a modest effect on increasing propionic acid degradation rate. It is also revealed that Ni shows some inhibitory effects on VFA degradation, possibly due to its toxicity. Additionally, regression coefficients for the main and second order effects are calculated to establish regression models for VFA degradation. Copyright © 2017 Elsevier Ltd. All rights reserved.

  2. Automatic Classification of Station Quality by Image Based Pattern Recognition of Ppsd Plots

    Science.gov (United States)

    Weber, B.; Herrnkind, S.

    2017-12-01

    The number of seismic stations is growing and it became common practice to share station waveform data in real-time with the main data centers as IRIS, GEOFON, ORFEUS and RESIF. This made analyzing station performance of increasing importance for automatic real-time processing and station selection. The value of a station depends on different factors as quality and quantity of the data, location of the site and general station density in the surrounding area and finally the type of application it can be used for. The approach described by McNamara and Boaz (2006) became standard in the last decade. It incorporates a probability density function (PDF) to display the distribution of seismic power spectral density (PSD). The low noise model (LNM) and high noise model (HNM) introduced by Peterson (1993) are also displayed in the PPSD plots introduced by McNamara and Boaz allowing an estimation of the station quality. Here we describe how we established an automatic station quality classification module using image based pattern recognition on PPSD plots. The plots were split into 4 bands: short-period characteristics (0.1-0.8 s), body wave characteristics (0.8-5 s), microseismic characteristics (5-12 s) and long-period characteristics (12-100 s). The module sqeval connects to a SeedLink server, checks available stations, requests PPSD plots through the Mustang service from IRIS or PQLX/SQLX or from GIS (gempa Image Server), a module to generate different kind of images as trace plots, map plots, helicorder plots or PPSD plots. It compares the image based quality patterns for the different period bands with the retrieved PPSD plot. The quality of a station is divided into 5 classes for each of the 4 bands. Classes A, B, C, D define regular quality between LNM and HNM while the fifth class represents out of order stations with gain problems, missing data etc. Over all period bands about 100 different patterns are required to classify most of the stations available on the

  3. Magnets for TRIUMF's KAON factory

    International Nuclear Information System (INIS)

    Otter, A.J.; Reeve, P.A.

    1991-05-01

    The KAON Factory will require over 2000 magnets to transport protons from the existing 500 Mev cyclotron through three storage rings and two synchrotrons and deliver them to the experimental area at 30 Gev. The magnet requirements are summarized and the results of measurements on prototypes for the 50 hz Booster magnets are compared with design values. This paper will address three topics: the results of prototype work, some of the more difficult design aspects of other magnets and the tolerances required to achieve production magnets uniform to ± 2 parts in 10 4 . (Author) 10 refs., 3 figs., tab

  4. Formulation optimization of gentamicin loaded Eudragit RS100 microspheres using factorial design study.

    Science.gov (United States)

    Singh, Deependra; Saraf, Swarnlata; Dixit, Vinod Kumar; Saraf, Shailendra

    2008-04-01

    Gentamicin-Eudragit RS100 microspheres were prepared by modified double emulsion method. A 3(2) full factorial experiment was designed to study the effects of the composition of outer aqueous phase in terms of amount of glycerol (viscosity effect) and sodium chloride (osmotic pressure gradient effect) on the entrapment efficiency and % yield and microsphere size. The results of analysis of variance test for responses measured indicated that the test is significant (p>0.05). The contribution of sodium chloride concentration was found to be higher on entrapment efficiency and % yield, whereas glycerol produced significant effect on the mean diameter of microspheres. Microspheres demonstrated spherical particles in the size range of 33.24-60.43 microm. In vitro release profile of optimized formulation demonstrated sustained release for 24 h following Higuchi kinetics. Finally, drug bioactivity was found to remain intact after microencapsulation. Response surface graphs are presented to examine the effects of independent variables on the responses studied. Thus, by formulation design important parameters affecting formulation characteristics of gentamicin loaded Eudragit RS100 microspheres can be identified for controlled delivery with desirable characters in terms of maximum entrapment and yield.

  5. Review of kaon factory proposals

    International Nuclear Information System (INIS)

    Thiessen, H.A.

    1985-01-01

    Nuclear physics issues and particle physics issues for a kaon factory are discussed. Kaon factory accelerator proposals are then considered. Secondary beam considerations are covered and hardware development for a kaon factory is discussed. The prospects for construction are presented. 9 refs., 12 figs., 2 tabs

  6. Neutrino factories

    International Nuclear Information System (INIS)

    Dydak, F.

    2002-01-01

    The discovery of neutrino oscillations marks a major milestone in the history of neutrino physics, and opens a window to what lies beyond the Standard Model. Many current and forthcoming experiments will answer open questions; however, a major step forward, up to and possibly including CP violation in the neutrino mixing matrix, will be offered by the neutrino beams from a neutrino factory. The neutrino factory is a new concept for producing neutrino beams of unprecedented quality in terms of intensity, flavour composition, and precision of the beam parameters. These beams enable the exploration of otherwise inaccessible domains in neutrino oscillation physics by exploiting baselines of planetary dimensions. Suitable detectors pose formidable challenges but seem within reach with only moderate extrapolations from existing technologies. Although the main physics attraction of the neutrino factory is in the area of neutrino oscillations, an interesting spectrum of further opportunities ranging from high-precision, high-rate neutrino scattering to physics with high-intensity stopped muons comes with it

  7. The half-half plot

    NARCIS (Netherlands)

    Einmahl, J.H.J.; Gantner, M.

    2012-01-01

    The Half-Half (HH) plot is a new graphical method to investigate qualitatively the shape of a regression curve. The empirical HH-plot counts observations in the lower and upper quarter of a strip that moves horizontally over the scatterplot. The plot displays jumps clearly and reveals further

  8. Plasma physics plotting package

    International Nuclear Information System (INIS)

    Hyman, D.H.

    1981-02-01

    We describe a package of plotting routines that do up to six two- or three-dimensional plots on a frame with minimal loss of resolution. The package now runs on a PDP-10 with PLOT-10 TCS primitives and on a Control Data Corporation-7600 and a Cray-1 with TV80LIB primitives on the National Magnetic Fusion Energy Computer Center network. The package is portable to other graphics systems because only the primitive plot calls are used from the underlying system's graphics package

  9. Peer support for family carers of people with dementia, alone or in combination with group reminiscence in a factorial design: study protocol for a randomised controlled trial

    Directory of Open Access Journals (Sweden)

    Wenborn Jennifer

    2011-09-01

    Full Text Available Abstract Background Peer support interventions can improve carer wellbeing and interventions that engage both the carer and person with dementia can have significant mutual benefits. Existing research has been criticised for inadequate rigour of design or reporting. This paper describes the protocol for a complex trial that evaluates one-to-one peer support and a group reminiscence programme, both separately and together, in a factorial design. Design A 2 × 2 factorial multi-site randomised controlled trial of individual peer support and group reminiscence interventions for family carers and people with dementia in community settings in England, addressing both effectiveness and cost-effectiveness. Discussion The methods described in this protocol have implications for research into psychosocial interventions, particularly complex interventions seeking to test both individual and group approaches. Trial Registration ISRCTN37956201

  10. MatrixPlot: visualizing sequence constraints

    DEFF Research Database (Denmark)

    Gorodkin, Jan; Stærfeldt, Hans Henrik; Lund, Ole

    1999-01-01

    MatrixPlot: visualizing sequence constraints. Sub-title Abstract Summary : MatrixPlot is a program for making high-quality matrix plots, such as mutual information plots of sequence alignments and distance matrices of sequences with known three-dimensional coordinates. The user can add information...

  11. Distributed plot-making

    DEFF Research Database (Denmark)

    Jensen, Lotte Groth; Bossen, Claus

    2016-01-01

    different socio-technical systems (paper-based and electronic patient records). Drawing on the theory of distributed cognition and narrative theory, primarily inspired by the work done within health care by Cheryl Mattingly, we propose that the creation of overview may be conceptualised as ‘distributed plot......-making’. Distributed cognition focuses on the role of artefacts, humans and their interaction in information processing, while narrative theory focuses on how humans create narratives through the plot construction. Hence, the concept of distributed plot-making highlights the distribution of information processing...

  12. Particle identification at an asymmetric B Factory

    International Nuclear Information System (INIS)

    Coyle, P.; Eigen, G.; Hitlin, D.; Oddone, P.; Ratcliff, B.; Roe, N.; Va'vra, J.; Ypsilantis, T.

    1991-09-01

    Particle identification systems are an important component of any detector at a high-luminosity, asymmetric B Factory. In particular, excellent hadron identification is required to probe CP violation in B 0 decays to CP eigenstates. The particle identification systems discussed below also provide help in separating leptons from hadrons at low momenta. We begin this chapter with a discussion of the physics motivation for providing particle identification, the inherent limitations due to interactions and decays in flight, and the requirements for hermiticity and angular coverage. A special feature of an asymmetric B Factory is the resulting asymmetry in the momentum distribution as a function of polar angle; this will also be quantified and discussed. In the next section the three primary candidates, time-of-flight (TOF), energy loss (dE/dx), and Cerenkov counters, both ring-imaging and threshold, will be briefly described and evaluated. Following this, one of the candidates, a long-drift Cerenkov ring-imaging device, is described in detail to provide a reference design. Design considerations for a fast RICH are then described. A detailed discussion of aerogel threshold counter designs and associated R ampersand D conclude the chapter. 56 refs., 64 figs., 13 tabs

  13. RESPON TANAMAN KEDELAI TERHADAP PUPUK HAYATI MIKORIZA ARBUSKULA HASIL REKAYASA SPESIFIK GAMBUT

    Directory of Open Access Journals (Sweden)

    Iwan Sasli

    2013-03-01

    Full Text Available The objectives of  this research were to study the  effectiveness of arbuscular mycorrhizal biofertilizer on growth and yield of soybean in peat soil. The  experiment was arranged in a Split-Plot Design  with factorial pattern, consisting of two factors and three replications. The first factor was Mycorrhizal consisted  of the levels: without mycorrhizae, mycorrhizal from biofertilizer, and indigenous mycorrhizal propagule from  pineapple’s rhizosphere were as main-plot.  Dosage of phospate fertilizer  were as sub-plot consisted of:  100, 75,  50, and 25 kg P2O5.ha-1.  The research showed that the mycorrhizal biofertilizer can improve plant growth and increase the some variables, such as plant heights, days to flowering, number of productive branches, dry wight of 100 seeds, number of pods of plant, and the percentage of plant to mycorrhizal dependency. It can be concluded that the arbuscular mycorrhizal specific of peat can be developed as a biologiocal fertilizer and cope with limited nutrient in peat soils and to improve the efficiency of phopate fertilizer.Keyword : fertilizzer, mycorrhyzal,  peat, soybean

  14. Sample size requirements for separating out the effects of combination treatments: Randomised controlled trials of combination therapy vs. standard treatment compared to factorial designs for patients with tuberculous meningitis

    Directory of Open Access Journals (Sweden)

    Farrar Jeremy

    2011-02-01

    Full Text Available Abstract Background In certain diseases clinical experts may judge that the intervention with the best prospects is the addition of two treatments to the standard of care. This can either be tested with a simple randomized trial of combination versus standard treatment or with a 2 × 2 factorial design. Methods We compared the two approaches using the design of a new trial in tuberculous meningitis as an example. In that trial the combination of 2 drugs added to standard treatment is assumed to reduce the hazard of death by 30% and the sample size of the combination trial to achieve 80% power is 750 patients. We calculated the power of corresponding factorial designs with one- to sixteen-fold the sample size of the combination trial depending on the contribution of each individual drug to the combination treatment effect and the strength of an interaction between the two. Results In the absence of an interaction, an eight-fold increase in sample size for the factorial design as compared to the combination trial is required to get 80% power to jointly detect effects of both drugs if the contribution of the less potent treatment to the total effect is at least 35%. An eight-fold sample size increase also provides a power of 76% to detect a qualitative interaction at the one-sided 10% significance level if the individual effects of both drugs are equal. Factorial designs with a lower sample size have a high chance to be underpowered, to show significance of only one drug even if both are equally effective, and to miss important interactions. Conclusions Pragmatic combination trials of multiple interventions versus standard therapy are valuable in diseases with a limited patient pool if all interventions test the same treatment concept, it is considered likely that either both or none of the individual interventions are effective, and only moderate drug interactions are suspected. An adequately powered 2 × 2 factorial design to detect effects of

  15. On the Nature of Earth-Mars Porkchop Plots

    Science.gov (United States)

    Woolley, Ryan C.; Whetsel, Charles W.

    2013-01-01

    Porkchop plots are a quick and convenient tool to help mission designers plan ballistic trajectories between two bodies. Parameter contours give rise to the familiar 'porkchop' shape. Each synodic period the pattern repeats, but not exactly, primarily due to differences in inclination and non-zero eccentricity. In this paper we examine the morphological features of Earth-to-Mars porkchop plots and the orbital characteristics that create them. These results are compared to idealistic and optimized transfers. Conclusions are drawn about 'good' opportunities versus 'bad' opportunities for different mission applications.

  16. Design and alaysis of the PEP-II B-Factory HER QF5 quadrupole magnet

    International Nuclear Information System (INIS)

    Kendall, C.M.; Harvey, A.; Swan, J.; Yamamoto, R.; Yokota, T.; Tanabe, J.; Sullivan, M.; Wienands, U.

    1997-01-01

    The High Energy Ring (HER) in Stanford Linear Accelerator Center's PEP-II B-Factory employs two high field quality quadrupole magnets, labeled QF5, located in the Interaction Region (IR) symmetrically about the Interaction Point (IP), for final horizontal beam focusing. An asymmetric, septum, Collins quadrupole design is required for QF5 as a result of space constraints within the IR. Water cooled square hollow copper conductor is used in a two coil per pole configuration to develop the 61.7 kG/m and 82.2 kG/m gradients required for the HER 9 GeV and 12 GeV energy levels respectively. A 1.45 m long laminated iron core constructed in two halves with a 160 mm diameter aperture and pole tip shims shape the quadruple field. The QF5 field quality requirements include a multipole content of b n /b 2 ≤1 x 10 -4 for n = 3-15 at a radius of 78.1 mm. The QF5 quadrupole mechanical and magnetic design and analysis are presented

  17. Design, engineering, and construction of photosynthetic microbial cell factories for renewable solar fuel production.

    Science.gov (United States)

    Lindblad, Peter; Lindberg, Pia; Oliveira, Paulo; Stensjö, Karin; Heidorn, Thorsten

    2012-01-01

    There is an urgent need to develop sustainable solutions to convert solar energy into energy carriers used in the society. In addition to solar cells generating electricity, there are several options to generate solar fuels. This paper outlines and discusses the design and engineering of photosynthetic microbial systems for the generation of renewable solar fuels, with a focus on cyanobacteria. Cyanobacteria are prokaryotic microorganisms with the same type of photosynthesis as higher plants. Native and engineered cyanobacteria have been used by us and others as model systems to examine, demonstrate, and develop photobiological H(2) production. More recently, the production of carbon-containing solar fuels like ethanol, butanol, and isoprene have been demonstrated. We are using a synthetic biology approach to develop efficient photosynthetic microbial cell factories for direct generation of biofuels from solar energy. Present progress and advances in the design, engineering, and construction of such cyanobacterial cells for the generation of a portfolio of solar fuels, e.g., hydrogen, alcohols, and isoprene, are presented and discussed. Possibilities and challenges when introducing and using synthetic biology are highlighted.

  18. Design, Engineering, and Construction of Photosynthetic Microbial Cell Factories for Renewable Solar Fuel Production

    Energy Technology Data Exchange (ETDEWEB)

    Lindblad, Peter; Lindberg, Pia; Stensjoe, Karin (Photochemistry and Molecular Science, Dept. of Chemistry-Aangstroem Laboratory, Uppsala Univ., Uppsala (Sweden)), E-mail: Peter.Lindblad@kemi.uu.se; Oliveira, Paulo (Instituto de Biologia Molecular e Celular, Porto (Portugal)); Heidorn, Thorsten (Bioforsk-Norwegian Inst. for Agricultural and Environmental Research, Aas Oslo, (Norway))

    2012-03-15

    There is an urgent need to develop sustainable solutions to convert solar energy into energy carriers used in the society. In addition to solar cells generating electricity, there are several options to generate solar fuels. This paper outlines and discusses the design and engineering of photosynthetic microbial systems for the generation of renewable solar fuels, with a focus on cyanobacteria. Cyanobacteria are prokaryotic microorganisms with the same type of photosynthesis as higher plants. Native and engineered cyanobacteria have been used by us and others as model systems to examine, demonstrate, and develop photobiological H{sub 2} production. More recently, the production of carbon-containing solar fuels like ethanol, butanol, and isoprene have been demonstrated. We are using a synthetic biology approach to develop efficient photosynthetic microbial cell factories for direct generation of biofuels from solar energy. Present progress and advances in the design, engineering, and construction of such cyanobacterial cells for the generation of a portfolio of solar fuels, e.g., hydrogen, alcohols, and isoprene, are presented and discussed. Possibilities and challenges when introducing and using synthetic biology are highlighted

  19. Electrodialytic desalination of brackish water: determination of optimal experimental parameters using full factorial design

    Science.gov (United States)

    Gmar, Soumaya; Helali, Nawel; Boubakri, Ali; Sayadi, Ilhem Ben Salah; Tlili, Mohamed; Amor, Mohamed Ben

    2017-12-01

    The aim of this work is to study the desalination of brackish water by electrodialysis (ED). A two level-three factor (23) full factorial design methodology was used to investigate the influence of different physicochemical parameters on the demineralization rate (DR) and the specific power consumption (SPC). Statistical design determines factors which have the important effects on ED performance and studies all interactions between the considered parameters. Three significant factors were used including applied potential, salt concentration and flow rate. The experimental results and statistical analysis show that applied potential and salt concentration are the main effect for DR as well as for SPC. The effect of interaction between applied potential and salt concentration was observed for SPC. A maximum value of 82.24% was obtained for DR under optimum conditions and the best value of SPC obtained was 5.64 Wh L-1. Empirical regression models were also obtained and used to predict the DR and the SPC profiles with satisfactory results. The process was applied for the treatment of real brackish water using the optimal parameters.

  20. Application of a complete factorial design for the production of zeaxanthin by Flavobacterium sp.

    Science.gov (United States)

    Masetto, A; Flores-Cotera, L B; Díaz, C; Langley, E; Sanchez, S

    2001-01-01

    Utilizing a four-liter fermentor and applying a complete factorial design 2(3), the combined effects of agitation speed, aeration rate, and corn steep liquor concentration on zeaxanthin production by Flavobacterium sp. were studied. Maximum growth and production of total carotenoids and zeaxanthin were obtained at 600 rpm, 2 vvm and 4.6% corn steep liquor. Under these conditions, zeaxanthin represented 86% of the total carotenoids produced. Lower values of the variables studied resulted in lower growth, volumetric production of zeaxanthin and total carotenoids, and favored the formation of other carotenoids such as beta-carotene and canthaxanthin. The positive effects on growth and total carotenoids and zeaxanthin formation were in a large extent due to the interaction of agitation/corn steep liquor. However, aeration also had a positive effect on growth.

  1. The Design and Analysis of Split Row-Column Addressing Array for 2-D Transducer

    Directory of Open Access Journals (Sweden)

    Xu Li

    2016-09-01

    Full Text Available For 3-D ultrasound imaging, the row-column addressing (RCA with 2N connections for an N × N 2-D array makes the fabrication and interconnection simpler than the fully addressing with N2 connections. However, RCA degrades the image quality because of defocusing in signal channel direction in the transmit event. To solve this problem, a split row-column addressing scheme (SRCA is proposed in this paper. Rather than connecting all the elements in the signal channel direction together, this scheme divides the elements in the signal channel direction into several disconnected blocks, thus enables focusing beam access in both signal channel and switch channel directions. Selecting an appropriate split scheme is the key for SRCA to maintaining a reasonable tradeoff between the image quality and the number of connections. Various split schemes for a 32 × 32 array are fully investigated with point spread function (PSF analysis and imaging simulation. The result shows the split scheme with five blocks (4, 6, 12, 6, and 4 elements of each block can provide similar image quality to fully addressing. The splitting schemes for different array sizes from 16 × 16 to 96 × 96 are also discussed.

  2. Design, implementation, and experimental validation of optimal power split control for hybrid electric trucks

    NARCIS (Netherlands)

    Keulen, T. van; Mullem, D. van; Jager, B. van; Kessels, J.T.B.A.; Steinbuch, M.

    2012-01-01

    Hybrid electric vehicles require an algorithm that controls the power split between the internal combustion engine and electric machine(s), and the opening and closing of the clutch. Optimal control theory is applied to derive a methodology for a real-time optimal-control-based power split

  3. Energy usage in Beet Suger Factories. Sockerfabrikens energianvaendning; En systemstudie

    Energy Technology Data Exchange (ETDEWEB)

    Feltborg, G

    1990-02-01

    A computer program has been developed in order to simulate the energy consumption of beet sugar factories, for various plant configurations. The program is divided into five block units: Extraction and Juice purification, Juice concentration, Crystallization, Drying and finally the Power House. Each block consists of different modules, for example, a heat exchanger, an evaporator, a turbine and a dryer. The purpose of this project was to simulate some different system configurations of a sugar factory, whereby both new and previously used process technologies were utilized. The following parts of the process have been particularly emphasized: Power House - gas turbine, waste heat boiler. Drying - low-temperature dryer, steam dryer. Evaporation - vapour recompression. Crystallization - vapour recompression, continuous system. The different plant configurations have been compared to a reference factory, which is designed according to current technology used in a modern and well balanced Swedish factory. The comparisons are based upon the total power consumption as well as the total annual energy costs. Eleven different plant configurations were studied. The maximum power reduction is 36%, relative to the reference factory. The dissertation also contains an experimental study of a low-temperature drying process. The drying characteristics of pressed beet pulp were studied in a specially designed rotary dryer pilot plant. A number of parameters were varied i.e. the solid moisture content, air velocity, temperature and rotational speed. The results are given in terms of an apparent volumetric heat-transfer coefficient, determined from measured data. A mathematical model was established to determine the residence time of the material in the rotary dryer at different air velocities. (45 refs.).

  4. Informing the Uninformed: Optimizing the Consent Message Using a Fractional Factorial Design

    Science.gov (United States)

    Tait, Alan R.; Voepel-Lewis, Terri; Nair, Vijayan N.; Narisetty, Naveen N.; Fagerlin, Angela

    2013-01-01

    Objective Research information should be presented in a manner that promotes understanding. However, many parents and research subjects have difficulty understanding and making informed decisions. This study was designed to examine the effect of different communication strategies on parental understanding of research information. Participants 640 parents of children scheduled for elective surgery Design Observational study using a fractional factorial design Setting Large tertiary care children's hospital Interventions Parents were randomized to receive information about a hypothetical pain trial presented in one of 16 consent documents containing different combinations of 5 selected communication strategies (i.e., length, readability, processability [formatting], graphical display, and supplemental verbal disclosure). Main outcome measures Parents were interviewed to determine their understanding of the study elements (e.g., protocol, alternatives etc.) and their gist (main point) and verbatim (actual) understanding of the risks and benefits. Results Main effects for understanding were found for processability, readability, message length, use of graphics, and verbal discussion. Consent documents with high processability, 8th grade reading level, and graphics resulted in significantly greater gist and verbatim understanding compared with forms without these attributes (mean difference, 95% CI = 0.57, 0.26–0.88, correct responses out of 7 and 0.54, 0.20–0.88 correct responses out of 4 for gist and verbatim, respectively). Conclusions Results identified several communication strategy combinations that improved parents' understanding of research information. Adoption of these active strategies by investigators, clinicians, IRBs, and study sponsors represents a simple, practical, and inexpensive means to optimize the consent message and enhance parental, participant, and patient understanding. PMID:23700028

  5. Superconducting cavities for beauty factories

    International Nuclear Information System (INIS)

    Lengeler, H.

    1992-01-01

    The possibilities and merits of superconducting accelerating cavities for Beauty-factories are considered. There exist already large sc systems of size and frequency comparable to the ones needed for Beauty-factories. Their status and operation experience is discussed. A comparison of normal conducting and superconducting systems is done for two typical Beauty-factory rings

  6. Super B Factories

    Indian Academy of Sciences (India)

    B factory; CP violation; B meson; supersymmetry. PACS Nos 11.30.Hv; 11.30.Pb; 12.15.Hh; 12.15.Mm; 13.20.He; 13.20.Fc;. 13.35.Dx; 14.65.Fy. 1. Introduction. The two asymmetric B factories, PEP-II and KEK-B, and their companion detec- tors, BABAR and Belle, have produced a wealth of flavor physics results, subjecting.

  7. Fluoride removal from diluted solutions by Donnan dialysis using full factorial design

    Energy Technology Data Exchange (ETDEWEB)

    Boubakri, Ali; Helali, Nawel; Tlili, Mohamed; Amor, Mohamed Ben [Center of Researches and Water Technologies, Soliman (Turkey)

    2014-03-15

    Excessive fluoride concentration in potable water can lead to fluorosis of teeth and bones. In the present study, Donnan dialysis (DD) is applied for the removal of fluoride ions from diluted sodium fluoride solutions. A four factor two level (2{sup 4}) full factorial design was used to investigate the influence of different physico-chemical parameters on fluoride removal efficiency (Y{sub F}) and fluoride flux (J{sub F}) through anion exchange membrane. The statistical design determines factors which have the important effects on Donnan dialysis performance and studies all interactions among the considered parameters. The four significant factors were initial fluoride concentration, feed flow rate, temperature and agitation speed. The experimental results and statistical analysis show that the temperature and agitation speed have positive effects on fluoride removal efficiency and the initial fluoride concentration has a negative effect. In the case of fluoride flux, feed flow rate and initial concentration are the main effect and all factors have a positive effect. The interaction between studied parameters was not negligible on two responses. A maximum fluoride removal of 75.52% was obtained under optimum conditions and the highest value of fluoride flux obtained was 2.4 mg/cm{sup 2}·h. Empirical regression models were also obtained and used to predict the flux and the fluoride removal profiles with satisfactory results.

  8. Hydrogen Production from Semiconductor-based Photocatalysis via Water Splitting

    Directory of Open Access Journals (Sweden)

    Jeffrey C. S. Wu

    2012-10-01

    Full Text Available Hydrogen is the ideal fuel for the future because it is clean, energy efficient, and abundant in nature. While various technologies can be used to generate hydrogen, only some of them can be considered environmentally friendly. Recently, solar hydrogen generated via photocatalytic water splitting has attracted tremendous attention and has been extensively studied because of its great potential for low-cost and clean hydrogen production. This paper gives a comprehensive review of the development of photocatalytic water splitting for generating hydrogen, particularly under visible-light irradiation. The topics covered include an introduction of hydrogen production technologies, a review of photocatalytic water splitting over titania and non-titania based photocatalysts, a discussion of the types of photocatalytic water-splitting approaches, and a conclusion for the current challenges and future prospects of photocatalytic water splitting. Based on the literatures reported here, the development of highly stable visible–light-active photocatalytic materials, and the design of efficient, low-cost photoreactor systems are the key for the advancement of solar-hydrogen production via photocatalytic water splitting in the future.

  9. A distribution-free multi-factorial profiler for harvesting information from high-density screenings.

    Science.gov (United States)

    Besseris, George J

    2013-01-01

    Data screening is an indispensable phase in initiating the scientific discovery process. Fractional factorial designs offer quick and economical options for engineering highly-dense structured datasets. Maximum information content is harvested when a selected fractional factorial scheme is driven to saturation while data gathering is suppressed to no replication. A novel multi-factorial profiler is presented that allows screening of saturated-unreplicated designs by decomposing the examined response to its constituent contributions. Partial effects are sliced off systematically from the investigated response to form individual contrasts using simple robust measures. By isolating each time the disturbance attributed solely to a single controlling factor, the Wilcoxon-Mann-Whitney rank stochastics are employed to assign significance. We demonstrate that the proposed profiler possesses its own self-checking mechanism for detecting a potential influence due to fluctuations attributed to the remaining unexplainable error. Main benefits of the method are: 1) easy to grasp, 2) well-explained test-power properties, 3) distribution-free, 4) sparsity-free, 5) calibration-free, 6) simulation-free, 7) easy to implement, and 8) expanded usability to any type and size of multi-factorial screening designs. The method is elucidated with a benchmarked profiling effort for a water filtration process.

  10. A distribution-free multi-factorial profiler for harvesting information from high-density screenings.

    Directory of Open Access Journals (Sweden)

    George J Besseris

    Full Text Available Data screening is an indispensable phase in initiating the scientific discovery process. Fractional factorial designs offer quick and economical options for engineering highly-dense structured datasets. Maximum information content is harvested when a selected fractional factorial scheme is driven to saturation while data gathering is suppressed to no replication. A novel multi-factorial profiler is presented that allows screening of saturated-unreplicated designs by decomposing the examined response to its constituent contributions. Partial effects are sliced off systematically from the investigated response to form individual contrasts using simple robust measures. By isolating each time the disturbance attributed solely to a single controlling factor, the Wilcoxon-Mann-Whitney rank stochastics are employed to assign significance. We demonstrate that the proposed profiler possesses its own self-checking mechanism for detecting a potential influence due to fluctuations attributed to the remaining unexplainable error. Main benefits of the method are: 1 easy to grasp, 2 well-explained test-power properties, 3 distribution-free, 4 sparsity-free, 5 calibration-free, 6 simulation-free, 7 easy to implement, and 8 expanded usability to any type and size of multi-factorial screening designs. The method is elucidated with a benchmarked profiling effort for a water filtration process.

  11. Planned Positron Factory project

    International Nuclear Information System (INIS)

    Okada, Sohei

    1990-01-01

    The Japan Atomic Energy Research Institute, JAERI, has started, drafting a construction plan for the 'Positron Factory', in which intense energy-controllable monoenergetic positron beams are produced from pair-production reactions caused by high-energy electrons from a linac. The JAERI organized a planning committee to provide a basic picture for the Positron Factory. This article presents an overview of the interactions of positrons, intense positron sources and the research program and facilities planned for the project. The interactions of positrons and intense positron sources are discussed focusing on major characteristics of positrons in different energy ranges. The research program for the Positron Factory is then outlined, focusing on advanced positron annihilation techniques, positron spectroscopy (diffraction, scattering, channeling, microscopy), basic positron physics (exotic particle science), and positron beam technology. Discussion is also made of facilities required for the Positron Factory. (N.K.)

  12. Effect of polymer type on characteristics of buccal tablets using factorial design

    Directory of Open Access Journals (Sweden)

    O. Esim

    2018-01-01

    Full Text Available A two factor three level factorial design was used to investigate the effects of carbopol and cationic hydrophilic polymers which have a common use in buccal drug formulations. Statistical models with interaction terms were derived to evaluate influence of carbopol (X1 and chitosan (X2 on tablet disintegration (Y1 and dissolution (Y2, mechanical properties (Y3, swelling (Y4. Tablet disintegration studies were carried out using two different pH environments within buccal region pH limits and also two different commonly used dissolution methods for buccal tablets were also investigated to compare the effect of polymer type on dissolution. Polymer type and ratio affect the characteristics of the buccal tablets due to their different physicochemical behavior at buccal pH. Also significant variances between dissolution profiles for buccal tablets, using either USP Paddle or flow through cell methods were found. These results indicate that both polymer type and ratio as well as combination of them effects the drug behavior in different ways. Keywords: Buccal tablet, Hydrophilic matrix, Effect of polymer, Carbopol, Chitosan

  13. A kaon factory for TRIUMF

    International Nuclear Information System (INIS)

    Measday, D.F.

    1988-11-01

    The design study for the TRIUMF Kaon Factory has recently been funded. A short discussion of the scientific motivation is given first, followed by a brief description of the 30 GeV synchrotron which is being proposed. There will be five rings altogether using the present TRIUMF 500 MeV cyclotron as an injector. If the project is funded in 1990 the accelerators would be completed in 1995 or so, and the experimental programme would start a year later

  14. Advanced Envelope Research for Factory Built Housing, Phase 3. Design Development and Prototyping

    Energy Technology Data Exchange (ETDEWEB)

    Levy, E. [ARIES Collaborative, New York, NY (United States); Kessler, B. [ARIES Collaborative, New York, NY (United States); Mullens, M. [ARIES Collaborative, New York, NY (United States); Rath, P. [ARIES Collaborative, New York, NY (United States)

    2014-01-01

    The Advanced Envelope Research effort will provide factory homebuilders with high performance, cost-effective alternative envelope designs. In the near term, these technologies will play a central role in meeting stringent energy code requirements. For manufactured homes, the thermal requirements, last updated by statute in 1994, will move up to the more rigorous IECC 2012 levels in 2013, the requirements of which are consistent with site built and modular housing. This places added urgency on identifying envelope technologies that the industry can implement in the short timeframe. The primary goal of this research is to develop wall designs that meet the thermal requirements based on 2012 IECC standards. Given the affordable nature of manufactured homes, impact on first cost is a major consideration in developing the new envelope technologies. This work is part of a four-phase, multi-year effort. Phase 1 identified seven envelope technologies and provided a preliminary assessment of three selected methods for building high performance wall systems. Phase 2 focused on the development of viable product designs, manufacturing strategies, addressing code and structural issues, and cost analysis of the three selected options. An industry advisory committee helped critique and select the most viable solution to move further in the research -- stud walls with continuous exterior insulation. Phase 3, the subject of the current report, focused on the design development of the selected wall concept and explored variations on the use of exterior foam insulation. The scope also included material selection, manufacturing and cost analysis, and prototyping and testing.

  15. Advanced Envelope Research for Factory Built Housing, Phase 3 -- Design Development and Prototyping

    Energy Technology Data Exchange (ETDEWEB)

    Levy, E. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Kessler, B. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Mullens, M. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Rath, P. [National Renewable Energy Lab. (NREL), Golden, CO (United States)

    2014-01-01

    The Advanced Envelope Research effort will provide factory homebuilders with high performance, cost-effective alternative envelope designs. In the near term, these technologies will play a central role in meeting stringent energy code requirements. For manufactured homes, the thermal requirements, last updated by statute in 1994, will move up to the more rigorous IECC 2012 levels in 2013, the requirements of which are consistent with site built and modular housing. This places added urgency on identifying envelope technologies that the industry can implement in the short timeframe. The primary goal of this research is to develop wall designs that meet the thermal requirements based on 2012 IECC standards. Given the affordable nature of manufactured homes, impact on first cost is a major consideration in developing the new envelope technologies. This work is part of a four-phase, multi-year effort. Phase 1 identified seven envelope technologies and provided a preliminary assessment of three selected methods for building high performance wall systems. Phase 2 focused on the development of viable product designs, manufacturing strategies, addressing code and structural issues, and cost analysis of the three selected options. An industry advisory committee helped critique and select the most viable solution to move further in the research -- stud walls with continuous exterior insulation. Phase 3, the subject of the current report, focused on the design development of the selected wall concept and explored variations on the use of exterior foam insulation. The scope also included material selection, manufacturing and cost analysis, and prototyping and testing.

  16. Algebraic techniques for diagonalization of a split quaternion matrix in split quaternionic mechanics

    International Nuclear Information System (INIS)

    Jiang, Tongsong; Jiang, Ziwu; Zhang, Zhaozhong

    2015-01-01

    In the study of the relation between complexified classical and non-Hermitian quantum mechanics, physicists found that there are links to quaternionic and split quaternionic mechanics, and this leads to the possibility of employing algebraic techniques of split quaternions to tackle some problems in complexified classical and quantum mechanics. This paper, by means of real representation of a split quaternion matrix, studies the problem of diagonalization of a split quaternion matrix and gives algebraic techniques for diagonalization of split quaternion matrices in split quaternionic mechanics

  17. Kaon factories

    International Nuclear Information System (INIS)

    Craddock, M.K.

    1983-03-01

    Kaon factories would provide beams 100-1000 times more intense than those available from present accelerators in the 10-30 GeV range. More intense or cleaner secondary beams of kaons, antiprotons and neutrinos would be of particular interest for high precision experiments and studies of rare processes in both particle and nuclear physics, e.g. symmetry violations in K-decay, neutrino scattering, meson and baryon spectroscopy, hypernuclei, exotic atoms, K + studies of nuclear density and resonance propagation in nuclei. The various accelerators proposed include both fast-cycling synchrotrons providing 100 μA proton beams at 15 to 32 GeV and superconducting isochronous ring cyclotrons giving 100-400 μA at up to 15 GeV. This paper describes these designs and the various technical problems associated with them

  18. Neutrino Factory and Muon Collider Collaboration R and D Program

    International Nuclear Information System (INIS)

    Zisman, M.S.

    2000-01-01

    The Neutrino Factory and Muon Collider Collaboration (MC) comprises some 140 scientists and engineers located at U.S. National Laboratories and Universities, and at a number of non-U.S. research institutions. In the past year, the MC R and D program has shifted its focus mainly toward the design issues related to the development of a Neutrino Factory based on a muon storage ring. In this paper the status of the various R and D activities is described, and future plans are outlined

  19. An operator-console system of the photon factory injector LINAC

    International Nuclear Information System (INIS)

    Nakahara, Kazuo; Abe, Isamu; Furukawa, Kazuro; Kamikubota, Norihiko

    1990-01-01

    It is sometimes difficult to unify accelerator control systems constructed in different ways. This problem arose in unifying the control systems of the injector linac and the storage ring making up the Photon Factory of the National Laboratory for High Energy Physics. One easy approach is to unify only the operator consoles; the unified console is connected to both separate control systems using gateways. The operator-console system of the Photon Factory injector linac has been designed and constructed using this approach. It consists of several workstations interconnected via a local-area network, a gateway to the old linac control network and a CATV system for the real-time display of the accelerator status. In this way the linac will be controlled from the control center of the Photon Factory storage ring. (orig.)

  20. Microbiological properties and oxidizable organic carbon fractions of an oxisol under coffee with split phosphorus applications and irrigation regimes

    Directory of Open Access Journals (Sweden)

    Adriana Rodolfo da Costa

    2013-02-01

    Full Text Available Phosphorus fertilization and irrigation increase coffee production, but little is known about the effect of these practices on soil organic matter and soil microbiota in the Cerrado. The objective of this study was to evaluate the microbiological and oxidizable organic carbon fractions of a dystrophic Red Latossol under coffee and split phosphorus (P applications and different irrigation regimes. The experiment was arranged in a randomized block design in a 3 x 2 factorial design with three split P applications (P1: 300 kg ha-1 P2O5, recommended for the crop year, of which two thirds were applied in September and the third part in December; P2: 600 kg ha-1 P2O5, applied at planting and then every two years, and P3: 1,800 kg ha-1 P2O5, the requirement for six years, applied at once at planting, two irrigation regimes (rainfed and year-round irrigation, with three replications. The layers 0-5 and 5-10 cm were sampled to determine microbial biomass carbon (MBC, basal respiration (BR, enzyme activity of acid phosphatase, the oxidizable organic carbon fractions (F1, F2, F3, and F4, and total organic carbon (TOC. The irrigation regimes increased the levels of MBC, microbial activity and acid phosphatase, TOC and oxidizable fractions of soil organic matter under coffee. In general, the form of dividing P had little influence on the soil microbial properties and OC. Only P3 under irrigation increased the levels of MBC and acid phosphatase activity.

  1. Design of a Low Cost Smart Dryer Temperature Measurement System for Tea Factories

    Directory of Open Access Journals (Sweden)

    Utpal SARMA

    2009-09-01

    Full Text Available This paper presents the design of a low cost smart dryer temperature measurement system for Tea Factories using K-type Thermocouple implementing linearization polynomial. The thermo emf is amplified by an instrumentation amplifier having high CMRR (106 dB and high input impedance (1012 Ohm. The analog signal is converted to digital form with the help of an SPI compatible 12-bit ADC. Data acquisition and transmission is done with an 8- bit microcontroller. As the dependence of thermo emf on temperature is not linear hence it is fitted with a polynomial. NIST data for K-type TC is taken as a standard for this fitting. The error with linear fit and polynomial fit is also presented. The digital data is corrected according to the polynomial and sent to a PC located at a remote control room for monitoring and data logging via RS232C communication. The performance of the entire system is discussed in the paper.

  2. Analysis of semi-solid processing for metal matrix composite synthesis using factorial design

    Directory of Open Access Journals (Sweden)

    Kratus Ranieri

    2012-02-01

    Full Text Available The main goal in this work is to conduct a quantitative analysis of the mechanical stir casting process for obtaining particulate metal matrix composites. A combined route of stirring at semi-solid state followed by stirring at liquid state is proposed. A fractional factorial design was developed to investigate the influence and interactions of factors as: time, rotation, initial fraction and particle size, on the incorporated fraction. The best incorporations were obtained with all factors at high levels, as well as that very long stirring periods have no strong influence being particle size and rotation the most important factors on the incorporated fraction. Particle wetting occurs during stirring at semi-solid state, highlighting the importance of the interactions between particles and the alloy globularized phase. The role of the alloying element Mg as a wettability-promoting agent is discussed. The shear forces resulting from the stirring system is emphasized and understood as the effect of rotation itself added to the propeller blade geometry.

  3. Selected Chemical Properties of Soybean Rhizosphere Soil as Influenced by Cropping Systems, Rhizobium Inoculation, and the Supply of Phosphorus and Potassium after Two Consecutive Cropping Seasons

    Directory of Open Access Journals (Sweden)

    Daniel Nyoki

    2018-01-01

    Full Text Available The field experiment was carried out in northern Tanzania to assess the effects of intercropping systems, Rhizobium inoculation, and fertilization with P and K on chemical properties of soybean rhizosphere soil. The experiment was laid out in split-split plot design with 2 × 4 × 7 factorial arrangement replicated thrice. The main plots had two inoculation treatments and the subplots were comprised of four cropping systems which were sole maize, sole soybean, and two intercropping at different soybean spacing (75 × 20 and 75 × 40 cm. The fertilizer levels (kg/ha control (0 kg/ha; 20 K; 40 K; 26 P; 52 P; 26 P + 20 K; and 52 P + 40 K were assigned to sub-subplots. Statistical analysis was performed using ANOVA. Least Significant Difference was used to compare treatment means at p=0.05 significance level. The results indicated that rhizosphere soil chemical properties such as pH, organic carbon (OC, and macro- and micronutrients (N, P, Ca, Mg, and Na and Fe, Cu, Mn, and Zn, resp. were significantly increased in the Rhizobium inoculated soybean over the control. The supply of P and K fertilizers significantly increased the rhizosphere content of macronutrients (P, K, Ca, and Mg and also they altered the pH and EC of the rhizosphere soil relative to control.

  4. Software factory techniques applied to process control at CERN

    CERN Document Server

    Dutour, Mathias D

    2008-01-01

    The CERN Large Hadron Collider (LHC) requires constant monitoring and control of quantities of parameters to guarantee operational conditions. For this purpose, a methodology called UNICOS (UNIfied Industrial COntrols Systems) has been implemented to standardize the design of process control applications. To further accelerate the development of these applications, we migrated our existing UNICOS tooling suite toward a software factory in charge of assembling project, domain and technical information seamlessly into deployable PLC (Programmable logic Controller) - SCADA (Supervisory Control And Data Acquisition) systems. This software factory delivers consistently high quality by reducing human error and repetitive tasks, and adapts to user specifications in a cost-efficient way. Hence, this production tool is designed to encapsulate and hide the PLC and SCADA target platforms, enabling the experts to focus on the business model rather than specific syntaxes and grammars. Based on industry standard software, ...

  5. METABOLIC MODELLING IN THE DEVELOPMENT OF CELL FACTORIES BY SYNTHETIC BIOLOGY

    Directory of Open Access Journals (Sweden)

    Paula Jouhten

    2012-10-01

    Full Text Available Cell factories are commonly microbial organisms utilized for bioconversion of renewable resources to bulk or high value chemicals. Introduction of novel production pathways in chassis strains is the core of the development of cell factories by synthetic biology. Synthetic biology aims to create novel biological functions and systems not found in nature by combining biology with engineering. The workflow of the development of novel cell factories with synthetic biology is ideally linear which will be attainable with the quantitative engineering approach, high-quality predictive models, and libraries of well-characterized parts. Different types of metabolic models, mathematical representations of metabolism and its components, enzymes and metabolites, are useful in particular phases of the synthetic biology workflow. In this minireview, the role of metabolic modelling in synthetic biology will be discussed with a review of current status of compatible methods and models for the in silico design and quantitative evaluation of a cell factory.

  6. Towards energy transparent factories

    CERN Document Server

    Posselt, Gerrit

    2016-01-01

    This monograph provides a methodological approach for establishing demand-oriented levels of energy transparency of factories. The author presents a systematic indication of energy drivers and cost factors, taking into account the interdependencies between facility and production domains. Particular attention is given to energy flow metering and monitoring. Readers will also be provided with an in-depth description of a planning tool which allows for systematically deriving suitable metering points in complex factory environments. The target audience primarily comprises researchers and experts in the field of factory planning, but the book may also be beneficial for graduate students.

  7. Polymeric nanoparticles loaded with the 3,5,3´-triiodothyroacetic acid (Triac, a thyroid hormone: factorial design, characterization, and release kinetics

    Directory of Open Access Journals (Sweden)

    dos Santos KC

    2012-07-01

    Full Text Available Karen C dos Santos,1 Maria Fatima GF da Silva,1 Edenir R Pereira-Filho,1 Joao B Fernandes,1 Igor Polikarpov,2 Moacir R Forim11Department of Chemistry, Federal University of Sao Carlos, Sao Carlos, 2Physics Institute of Sao Carlos, University of Sao Paulo, Sao Carlos, Sao Paulo, BrazilAbstract: This present investigation deals with the development and optimization of polymeric nanoparticle systems loaded with 3,5,3´-triiodothyroacetic acid (Triac. A 211–6 fractional factorial design and another 22 factorial design were used to study the contrasts on particle size distribution, morphology, surface charge, drug content, entrapment efficiency, and in vitro drug release profiles. The independent variables were the concentration of Triac, type and quantity of both polymer and oil, quantity of Span™ 60 and Tween® 80, volume of solvent and water, and velocity of both magnetic stirring and the transfer of the organic phase into the aqueous solution. The results of optimized formulations showed a narrow size distribution with a polydispersity index lower than 0.200. The particle sizes were on average 159.6 nm and 285.6 nm for nanospheres and nanocapsules, respectively. The zeta potential was higher than 20 mV (in module and the entrapment efficiency was nearly 100%. A high-performance liquid chromatography method was developed, validated, and efficiently applied to Triac quantification in colloidal suspension. The main independent variables were the type and quantity of the polymer and oil. In vitro drug release profile depicted several features to sustain Triac release. Different formulations showed various release rates indicating an interaction between Triac and other formulation compounds such as polymer and/or oil quantity. Two different models were identified (biexponential and monoexponential that allowed the control of both the release rate and Triac concentration. Thus, the prepared nanoparticles described here may be of clinical importance

  8. Design of Experiments: Optimizing the Polycarboxylation/Functionalization of Tungsten Disulfide Nanotubes

    Directory of Open Access Journals (Sweden)

    Daniel Raichman

    2014-08-01

    Full Text Available Design of experiments (DOE methodology was used to identify and optimize factors that influence the degree of functionalization (polycarboxylation of WS2 INTs via a modified acidic Vilsmeier–Haack reagent. The six factors investigated were reaction time, temperature and the concentrations of 2-bromoacetic acid, WS2 INTs, silver acetate and DMF. The significance of each factor and the associated interactive effects were evaluated using a two-level factorial statistical design in conjunction with statistical software (MiniTab® 16 based on quadratic programming. Although statistical analysis indicated that no factors were statistically significant, time, temperature and concentration of silver acetate were found to be the most important contributors to obtaining maximum functionalization/carboxylation. By examining contour plots and interaction plots, it was determined that optimal functionalization is obtained in a temperature range of 115–120 °C with a reaction time of 54 h using a mixture of 6 mL DMF, 200 mg INTs, 800 mg 2-bromoacetic acid and 60 mg silver acetate.

  9. Deciding WQO for factorial languages

    KAUST Repository

    Atminas, Aistis; Lozin, Vadim V.; Moshkov, Mikhail

    2013-01-01

    A language is factorial if it is closed under taking factors (i.e. contiguous subwords). Every factorial language can be described by an antidictionary, i.e. a minimal set of forbidden factors. We show that the problem of deciding whether a factorial language given by a finite antidictionary is well-quasi-ordered under the factor containment relation can be solved in polynomial time. © 2013 Springer-Verlag Berlin Heidelberg.

  10. Deciding WQO for factorial languages

    KAUST Repository

    Atminas, Aistis

    2013-04-05

    A language is factorial if it is closed under taking factors (i.e. contiguous subwords). Every factorial language can be described by an antidictionary, i.e. a minimal set of forbidden factors. We show that the problem of deciding whether a factorial language given by a finite antidictionary is well-quasi-ordered under the factor containment relation can be solved in polynomial time. © 2013 Springer-Verlag Berlin Heidelberg.

  11. In-Factory Learning - Qualification For The Factory Of The Future

    Science.gov (United States)

    Quint, Fabian; Mura, Katharina; Gorecky, Dominic

    2015-07-01

    The Industry 4.0 vision anticipates that internet technologies will find their way into future factories replacing traditional components by dynamic and intelligent cyber-physical systems (CPS) that combine the physical objects with their digital representation. Reducing the gap between the real and digital world makes the factory environment more flexible, more adaptive, but also more complex for the human workers. Future workers require interdisciplinary competencies from engineering, information technology, and computer science in order to understand and manage the diverse interrelations between physical objects and their digital counterpart. This paper proposes a mixed-reality based learning environment, which combines physical objects and visualisation of digital content via Augmented Reality. It uses reality-based interaction in order to make the dynamic interrelations between real and digital factory visible and tangible. We argue that our learning system does not work as a stand-alone solution, but should fit into existing academic and advanced training curricula.

  12. Density Distribution Sunflower Plots

    Directory of Open Access Journals (Sweden)

    William D. Dupont

    2003-01-01

    Full Text Available Density distribution sunflower plots are used to display high-density bivariate data. They are useful for data where a conventional scatter plot is difficult to read due to overstriking of the plot symbol. The x-y plane is subdivided into a lattice of regular hexagonal bins of width w specified by the user. The user also specifies the values of l, d, and k that affect the plot as follows. Individual observations are plotted when there are less than l observations per bin as in a conventional scatter plot. Each bin with from l to d observations contains a light sunflower. Other bins contain a dark sunflower. In a light sunflower each petal represents one observation. In a dark sunflower, each petal represents k observations. (A dark sunflower with p petals represents between /2-pk k and /2+pk k observations. The user can control the sizes and colors of the sunflowers. By selecting appropriate colors and sizes for the light and dark sunflowers, plots can be obtained that give both the overall sense of the data density distribution as well as the number of data points in any given region. The use of this graphic is illustrated with data from the Framingham Heart Study. A documented Stata program, called sunflower, is available to draw these graphs. It can be downloaded from the Statistical Software Components archive at http://ideas.repec.org/c/boc/bocode/s430201.html . (Journal of Statistical Software 2003; 8 (3: 1-5. Posted at http://www.jstatsoft.org/index.php?vol=8 .

  13. Split warhead simultaneous impact

    Directory of Open Access Journals (Sweden)

    Rahul Singh Dhari

    2017-12-01

    Full Text Available A projectile system is proposed to improve efficiency and effectiveness of damage done by anti-tank weapon system on its target by designing a ballistic projectile that can split into multiple warheads and engage a target at the same time. This idea has been developed in interest of saving time consumed from the process of reloading and additional number of rounds wasted on target during an attack. The proposed system is achieved in three steps: Firstly, a mathematical model is prepared using the basic equations of motion. Second, An Ejection Mechanism of proposed warhead is explained with the help of schematics. Third, a part of numerical simulation which is done using the MATLAB software. The final result shows various ranges and times when split can be effectively achieved. With the new system, impact points are increased and hence it has a better probability of hitting a target.

  14. Enhancing biodegradation of wastewater by microbial consortia with fractional factorial design

    Energy Technology Data Exchange (ETDEWEB)

    Chen Yuancai [State Key Laboratory of Pulp and Paper Engineering, South China University of Technology, Guangzhou, 510640, Guangdong (China); Lin Chejen, E-mail: Jerry.Lin@lamar.edu [Department of Civil Engineering, Lamar University, Beaumont, TX 77710-0024 (United States); School of Environmental Science and Engineering, South China University of Technology, Guangzhou, 510006, Guangdong (China); Jones, Gavin [Texas Research Institute for Environmental Studies, Sam Houston State University, Huntsville, TX 77341-2506 (United States); Fu Shiyu; Zhan Huaiyu [State Key Laboratory of Pulp and Paper Engineering, South China University of Technology, Guangzhou, 510640, Guangdong (China)

    2009-11-15

    Batch experiments were conducted on the degradation of synthetic and municipal wastewater by six different strains, i.e., Agrobacterium sp., Bacillus sp., Enterobacter cloacae, Gordonia, Pseudomonas stutzeri, Pseudomonas putida. By applying a fractional factorial design (FFD) of experiments, the influence of each strain and their interactions were quantified. An empirical model predicting the treatment efficiency was built based on the results of the FFD experiments with an R{sup 2} value of 99.39%. For single strain, Enterobacter cloacae, Gordonia and P. putida (p = 0.008, 0.009 and 0.023, respectively) showed significant enhancement on organic removal in the synthetic wastewater. Positive interaction from Enterobacter cloacae, Gordonia (p = 0.046) was found, indicating that syntrophic interaction existed, and their coexistence can improve total organic carbon (TOC) degradation. Verification experiments were performed to evaluate the effect of bioaugmentation by introducing three selected strains into an activated sludge reactor for treating municipal wastewater. The removal efficiency of TOC with the bioaugmentation was increased from 67-72% to 80-84% at an influent TOC concentration of 200 mg/L. The results derived from this study indicate that the FFD is a useful screening tool for optimizing the microbial community to enhance treatment efficiency.

  15. Enhancing biodegradation of wastewater by microbial consortia with fractional factorial design

    International Nuclear Information System (INIS)

    Chen Yuancai; Lin Chejen; Jones, Gavin; Fu Shiyu; Zhan Huaiyu

    2009-01-01

    Batch experiments were conducted on the degradation of synthetic and municipal wastewater by six different strains, i.e., Agrobacterium sp., Bacillus sp., Enterobacter cloacae, Gordonia, Pseudomonas stutzeri, Pseudomonas putida. By applying a fractional factorial design (FFD) of experiments, the influence of each strain and their interactions were quantified. An empirical model predicting the treatment efficiency was built based on the results of the FFD experiments with an R 2 value of 99.39%. For single strain, Enterobacter cloacae, Gordonia and P. putida (p = 0.008, 0.009 and 0.023, respectively) showed significant enhancement on organic removal in the synthetic wastewater. Positive interaction from Enterobacter cloacae, Gordonia (p = 0.046) was found, indicating that syntrophic interaction existed, and their coexistence can improve total organic carbon (TOC) degradation. Verification experiments were performed to evaluate the effect of bioaugmentation by introducing three selected strains into an activated sludge reactor for treating municipal wastewater. The removal efficiency of TOC with the bioaugmentation was increased from 67-72% to 80-84% at an influent TOC concentration of 200 mg/L. The results derived from this study indicate that the FFD is a useful screening tool for optimizing the microbial community to enhance treatment efficiency.

  16. Ammonia-nitrogen and Phosphate Reduction by Bio-Filter using Factorial Design

    Science.gov (United States)

    Kasmuri, Norhafezah; Ashikin Mat Damin, Nur; Omar, Megawati

    2018-02-01

    Untreated landfill leachate is known to have endangered the environment. As such new treatment must be sought to ensure its cost-effective and sustainable treatment. Thus this paper reports the effectiveness of bio-filter to remove pollutants. In this research, the reduction of nutrients concentration was evaluated in two conditions: using bio-filter and without bio-filter. Synthetic wastewater was used in the batch culture. It was conducted within 21 days in the initial mediums of 100 mg/L ammonia-nitrogen. The nitrification medium consisted of 100 mg/L of ammonia-nitrogen while the nitrite assay had none. The petri dish experiment was also conducted to observe the existence of any colony. The results showed 22% of ammonia- nitrogen reduction and 33% phosphate in the nitrification medium with the bio-filter. The outcome showed that the bio-filter was capable to reduce the concentration of pollutants by retaining the slow growing bacteria (AOB and NOB) on the plastic carrier surface. The factorial design was applied to study the effect of the initial ammonia-nitrogen concentration and duration on nitrite-nitrogen removal. Finally, a regression equation was produced to predict the rate of nitrite-nitrogen removal without conducting extended experiments and to reduce the number of trials experiment.

  17. Bad splits in bilateral sagittal split osteotomy: systematic review of fracture patterns.

    Science.gov (United States)

    Steenen, S A; Becking, A G

    2016-07-01

    An unfavourable and unanticipated pattern of the mandibular sagittal split osteotomy is generally referred to as a 'bad split'. Few restorative techniques to manage the situation have been described. In this article, a classification of reported bad split pattern types is proposed and appropriate salvage procedures to manage the different types of undesired fracture are presented. A systematic review was undertaken, yielding a total of 33 studies published between 1971 and 2015. These reported a total of 458 cases of bad splits among 19,527 sagittal ramus osteotomies in 10,271 patients. The total reported incidence of bad split was 2.3% of sagittal splits. The most frequently encountered were buccal plate fractures of the proximal segment (types 1A-F) and lingual fractures of the distal segment (types 2A and 2B). Coronoid fractures (type 3) and condylar neck fractures (type 4) have seldom been reported. The various types of bad split may require different salvage approaches. Copyright © 2016 International Association of Oral and Maxillofacial Surgeons. Published by Elsevier Ltd. All rights reserved.

  18. Influence of solar irradiance, watering frequency and inorganic fertilizer on incidence of dieback disease and growth of Ceiba pentendra (L.) seedlings

    International Nuclear Information System (INIS)

    Nkyi, K.A.; Owusu-Sekyere, E.; Ofori, D.

    2012-01-01

    Efforts at raising seedlings of Ceiba pentandra in nurseries have been hampered by damping-off, leaf spots and stem anthracnose causing stem dieback disease by fungal attack. Managing the disease by fungicides retarded growth of the seedlings; hence a method of controlling the dieback disease and boosting growth of Ceiba pentandra seedlings based on environmental factors was investigated. Using a randomised complete block design in a factorial split-plot experiment, the dependence of survival and growth of Ceiba pentandra seedlings on solar irradiance, watering frequency and NPK (15:15:15) fertilizer was studied to improve the survival rate of seedlings by preventing dieback disease in large-scale plantation development in Ghana. Solar irradiance, daily watering of 4.5 L per plot and inorganic fertilizer application of 1.0 g per seedling had the strongest effect in minimizing the incidence of dieback disease and ensuring 90 % survival and improved collar diameter growth. The levels of irradiance, watering regime and optimum fertilizer application required to control dieback disease and promote growth of Ceiba pentandra seedlings were set, and could be adopted by tree growers. (au)

  19. Artificial Warming of Arctic Meadow under Pollution Stress: Experimental design

    Science.gov (United States)

    Moni, Christophe; Silvennoinen, Hanna; Fjelldal, Erling; Brenden, Marius; Kimball, Bruce; Rasse, Daniel

    2014-05-01

    split plots (diameter: 3.65 m & surface area: 10.5 m2) composed of one half amended with biochar and one control half not amended were prepared. Five of these plots are equipped with a warming system, while the other five were equipped with dummies. Each warmed plot is collocated with a control plot within one block. While split plots are all oriented in the same direction the position of blocks is randomized to eliminate the effect of the spatial variability. Biochar was incorporated in the first 20 cm of the soil with a rototiller. Warming system is provided by hexagonal arrays of infrared heaters. The temperature of the plots is monitored with infrared cameras. The 3oC increase of temperature is obtained by dynamically monitoring the temperature difference between warmed and control plots within blocks via improved software. Each plot is further equipped with a soil temperature and moisture sensor.

  20. Difference and ratio plots

    DEFF Research Database (Denmark)

    Svendsen, Anders Jørgen; Holmskov, U; Bro, Peter

    1995-01-01

    and systemic lupus erythematosus from another previously published study (Macanovic, M. and Lachmann, P.J. (1979) Clin. Exp. Immunol. 38, 274) are also represented using ratio plots. Our observations indicate that analysis by regression analysis may often be misleading....... hitherto unnoted differences between controls and patients with either rheumatoid arthritis or systemic lupus erythematosus. For this we use simple, but unconventional, graphic representations of the data, based on difference plots and ratio plots. Differences between patients with Burkitt's lymphoma...

  1. Preliminary conceptual design for a 510 MeV electron/positron injector for a UCLA φ factory

    International Nuclear Information System (INIS)

    Dahlbacka, G.; Hartline, R.; Barletta, W.; Pellegrini, C.

    1991-01-01

    UCLA is proposing a compact suer conducting high luminosity (10 32-33 cm -2 sec -1 ) e + e - collider for a φ factory. To achieve the required e + e - currents, full energy injections from a linac with intermediate storage in a Positron Accumulator Ring (PAR) is used. The elements of the linac are outlined with cost and future flexibility in mind. The preliminary conceptual design starts with a high current gun similar in design to those developed at SLAC and at ANL (for the APS). Four 4-section linac modules follow, each driven by a 60 MW klystron with a 1 μsec macropulse and an average current of 8.6 A. The first 4-section model is used to create positrons in a tungsten target at 186 MeV. The three remaining three modules are used to accelerate the e + e - beam to 558 MeV (no load limit) for injection into the PAR

  2. The Operator Guide: An Ambient Persuasive Interface in the Factory

    Science.gov (United States)

    Meschtscherjakov, Alexander; Reitberger, Wolfgang; Pöhr, Florian; Tscheligi, Manfred

    In this paper we introduce the context of a semiconductor factory as a promising area for the application of innovative interaction approaches. In order to increase efficiency ambient persuasive interfaces, which influence the operators' behaviour to perform in an optimized way, could constitute a potential strategy. We present insights gained from qualitative studies conducted in a specific semiconductor factory and provide a description of typical work processes and already deployed interfaces in this context. These findings informed the design of a prototype of an ambient persuasive interface within this realm - the "Operator Guide". Its overall aim is to improve work efficiency, while still maintaining a minimal error rate. We provide a detailed description of the Operator Guide along with an outlook of the next steps within a user-centered design approach.

  3. Reward-allocation judgments in Romania : A factorial survey approach

    NARCIS (Netherlands)

    Buzea, C.; Meseşan-Schmitz, L.; van de Vijver, F.J.R.

    2013-01-01

    We investigated reward-allocation judgments when positive outcomes (monetary rewards) were distributed and the allocator was not a co-recipient, in a sample of 200 Romanian students. Within a full factorial survey design, seven factors, selected to affect the allocation decision, were orthogonally

  4. Full factorial design applied to the synthesis of Pd-?Ag nanobars by the polyol method and the perspective for ethanol oxidation

    OpenAIRE

    Carrera-Cerritos, Raul; Ponce de Leon, Carlos; Ledesma-Garcia, J.; Fuentes-Ramirez, R.; Arriaga, L.G.

    2014-01-01

    Full factorial design methodology was applied to the synthesis and optimization of Pd–Ag nanobars usingthe polyol process as the reducer. The concentration of Br? ions, the temperature and the reaction timewere selected as factors to study, whereas the yield (% nanobars) was the response to be analyzed. Thenanoparticles were characterized by X-ray diffraction, energy-dispersive X-ray spectroscopy,transmission electron microscopy, high-resolution transmission electron microscopy and X-rayphoto...

  5. R and D Toward Neutrino Factories and Muon Colliders

    International Nuclear Information System (INIS)

    Zisman, Michael S.

    2003-01-01

    R and D aimed at the production, acceleration, and storage of intense muon beams is under way in the U.S., in Europe, and in Japan. Considerable progress has been made in the past few years toward the design of a ''Neutrino Factory'' in which a beam of 20-50 GeV mu- or mu+ is stored. Decay neutrinos from the beam illuminate a detector located roughly 3000 km from the ring. Here, we briefly describe the ingredients of a Neutrino Factory and then discuss the current R and D program and its results. A key concept in the design is ''ionization cooling,'' a process whereby the muon emittance is reduced by repeated interactions with an absorber material followed by reacceleration with high-gradient rf cavities. Plans to test this concept in the Muon Ionization Cooling Experiment (MICE) are well along and are described briefly

  6. Software factory techniques applied to Process Control at CERN

    CERN Multimedia

    Dutour, MD

    2007-01-01

    The CERN Large Hadron Collider (LHC) requires constant monitoring and control of quantities of parameters to guarantee operational conditions. For this purpose, a methodology called UNICOS (UNIfied Industrial COntrols Systems) has been implemented to standardize the design of process control applications. To further accelerate the development of these applications, we migrated our existing UNICOS tooling suite toward a software factory in charge of assembling project, domain and technical information seamlessly into deployable PLC (Programmable logic Controller) – SCADA (Supervisory Control And Data Acquisition) systems. This software factory delivers consistently high quality by reducing human error and repetitive tasks, and adapts to user specifications in a cost-efficient way. Hence, this production tool is designed to encapsulate and hide the PLC and SCADA target platforms, enabling the experts to focus on the business model rather than specific syntaxes and grammars. Based on industry standard software...

  7. The Smart Factory

    DEFF Research Database (Denmark)

    Radziwon, Agnieszka; Bilberg, Arne; Bogers, Marcel

    2014-01-01

    Nowadays we live in a world, which a decade ago would only be described in the science fiction literature. More and more things become smart and both scientists and engineers strive for developing not only new and innovative devices, but also homes, factories, or even cities. Despite of continuous...... development, many of those concepts are still being just a vision of the future, which still needs a lot of effort to become true. This paper reviews the usage of adjective smart in respect to technology and with a special emphasis on the smart factory concept placement among contemporary studies. Due...... to a lack of a consensus of common understanding of this term, a unified definition is proposed. The conceptualization will not only refer to various smart factory visions reported in the literature, but also link the crucial characteristics of this emerging manufacturing concept to usual manufacturing...

  8. Tau/Charm Factory Accelerator Report

    OpenAIRE

    M. E. BiaginiINFN, Laboratori Nazionali Frascati, Italy; R. BoniINFN, Laboratori Nazionali Frascati, Italy; M. BoscoloINFN, Laboratori Nazionali Frascati, Italy; A. ChiarucciINFN, Laboratori Nazionali Frascati, Italy; R. CiminoINFN, Laboratori Nazionali Frascati, Italy; A. ClozzaINFN, Laboratori Nazionali Frascati, Italy; A. DragoINFN, Laboratori Nazionali Frascati, Italy; S. GuiducciINFN, Laboratori Nazionali Frascati, Italy; C. LigiINFN, Laboratori Nazionali Frascati, Italy; G. MazzitelliINFN, Laboratori Nazionali Frascati, Italy; R. RicciINFN, Laboratori Nazionali Frascati, Italy; C. SanelliINFN, Laboratori Nazionali Frascati, Italy; M. SerioINFN, Laboratori Nazionali Frascati, Italy; A. StellaINFN, Laboratori Nazionali Frascati, Italy; S. TomassiniINFN, Laboratori Nazionali Frascati, Italy

    2014-01-01

    The present Report concerns the current status of the Italian Tau/Charm accelerator project and in particular discusses the issues related to the lattice design, to the accelerators systems and to the associated conventional facilities. The project aims at realizing a variable energy Flavor Factory between 1 and 4.6 GeV in the center of mass, and succeeds to the SuperB project from which it inherits most of the solutions proposed in this document. The work comes from a cooperation involving t...

  9. Neutrino factory and muon collider collaboration R and D activities

    International Nuclear Information System (INIS)

    Zisman, Michael S.; Neutrino Factory and Muon Collider Collaborat

    2001-01-01

    The Neutrino Factory and Muon Collider Collaboration (MC) comprises about 140 U.S. and non-U.S. accelerator and particle physicists. The MC is carrying out an R and D program aimed at validating the critical design concepts required for the construction of such machines. We are committed to encouraging international cooperation and coordination of the R and D effort. Main activities of the MC include a Targetry program, a MUCOOL program, a component development program, and a theory and simulation effort. Moreover, the MC has participated in several feasibility studies for a complete Neutrino Factory facility, with the aim of identifying any additional R and D activities needed to prepare a Zeroth-order Design Report (ZDR) in about two years and a Conceptual Design report (CDR) about two years thereafter. In this paper, the R and D goals in each area will be indicated, and the present status and future plans of the R and D program will be described

  10. Modeling Short-Range Soil Variability and its Potential Use in Variable-Rate Treatment of Experimental Plots

    Directory of Open Access Journals (Sweden)

    A Moameni

    2011-02-01

    Full Text Available Abstract In Iran, the experimental plots under fertilizer trials are managed in such a way that the whole plot area uniformly receives agricultural inputs. This could lead to biased research results and hence to suppressing of the efforts made by the researchers. This research was conducted in a selected site belonging to the Gonbad Agricultural Research Station, located in the semiarid region, northeastern Iran. The aim was to characterize the short-range spatial variability of the inherent and management-depended soil properties and to determine if this variation is large and can be managed at practical scales. The soils were sampled using a grid 55 m apart. In total, 100 composite soil samples were collected from topsoil (0-30 cm and were analyzed for calcium carbonate equivalent, organic carbon, clay, available phosphorus, available potassium, iron, copper, zinc and manganese. Descriptive statistics were applied to check data trends. Geostatistical analysis was applied to variography, model fitting and contour mapping. Sampling at 55 m made it possible to split the area of the selected experimental plot into relatively uniform areas that allow application of agricultural inputs with variable rates. Keywords: Short-range soil variability, Within-field soil variability, Interpolation, Precision agriculture, Geostatistics

  11. Market Structure and Stock Splits

    OpenAIRE

    David Michayluk; Paul Kofman

    2001-01-01

    Enhanced liquidity is one possible motivation for stock splits but empirical research frequently documents declines in liquidity following stock splits. Despite almost thirty years of inquiry, little is known about all the changes in a stock's trading activity following a stock split. We examine how liquidity measures change around more than 2,500 stock splits and find a pervasive decline in most measures. Large stock splits exhibit a more severe liquidity decline than small stock splits, esp...

  12. Mucoadhesive Hydrogel Films of Econazole Nitrate: Formulation and Optimization Using Factorial Design

    Directory of Open Access Journals (Sweden)

    Balaram Gajra

    2014-01-01

    Full Text Available The mucoadhesive hydrogel film was prepared and optimized for the purpose of local drug delivery to oral cavity for the treatment of oral Candidiasis. The mucoadhesive hydrogel film was prepared with the poly(vinyl alcohol by freeze/thaw crosslinking technique. 32 full factorial design was employed to optimize the formulation. Number of freeze/thaw cycles (4, 6, and 8 cycles and the concentration of the poly(vinyl alcohol (10, 15, and 20% were used as the independent variables whereas time required for 50% drug release, cumulative percent of drug release at 8th hour, and “k” of zero order equation were used as the dependent variables. The films were evaluated for mucoadhesive strength, in vitro residence time, swelling study, in vitro drug release, and effectiveness against Candida albicans. The concentration of poly(vinyl alcohol and the number of freeze/thaw cycles both decrease the drug release rate. Mucoadhesive hydrogel film with 15% poly(vinyl alcohol and 7 freeze/thaw cycles was optimized. The optimized batch exhibited the sustained release of drug and the antifungal studies revealed that the drug released from the film could inhibit the growth of Candida albicans for 12 hours.

  13. A systematic approach to designing statistically powerful heteroscedastic 2 × 2 factorial studies while minimizing financial costs

    Directory of Open Access Journals (Sweden)

    Show-Li Jan

    2016-08-01

    Full Text Available Abstract Background The 2 × 2 factorial design is widely used for assessing the existence of interaction and the extent of generalizability of two factors where each factor had only two levels. Accordingly, research problems associated with the main effects and interaction effects can be analyzed with the selected linear contrasts. Methods To correct for the potential heterogeneity of variance structure, the Welch-Satterthwaite test is commonly used as an alternative to the t test for detecting the substantive significance of a linear combination of mean effects. This study concerns the optimal allocation of group sizes for the Welch-Satterthwaite test in order to minimize the total cost while maintaining adequate power. The existing method suggests that the optimal ratio of sample sizes is proportional to the ratio of the population standard deviations divided by the square root of the ratio of the unit sampling costs. Instead, a systematic approach using optimization technique and screening search is presented to find the optimal solution. Results Numerical assessments revealed that the current allocation scheme generally does not give the optimal solution. Alternatively, the suggested approaches to power and sample size calculations give accurate and superior results under various treatment and cost configurations. Conclusions The proposed approach improves upon the current method in both its methodological soundness and overall performance. Supplementary algorithms are also developed to aid the usefulness and implementation of the recommended technique in planning 2 × 2 factorial designs.

  14. SpectraPLOT, Visualization Package with a User-Friendly Graphical Interface

    Science.gov (United States)

    Sebald, James; Macfarlane, Joseph; Golovkin, Igor

    2017-10-01

    SPECT3D is a collisional-radiative spectral analysis package designed to compute detailed emission, absorption, or x-ray scattering spectra, filtered images, XRD signals, and other synthetic diagnostics. The spectra and images are computed for virtual detectors by post-processing the results of hydrodynamics simulations in 1D, 2D, and 3D geometries. SPECT3D can account for a variety of instrumental response effects so that direct comparisons between simulations and experimental measurements can be made. SpectraPLOT is a user-friendly graphical interface for viewing a wide variety of results from SPECT3D simulations, and applying various instrumental effects to the simulated images and spectra. We will present SpectraPLOT's ability to display a variety of data, including spectra, images, light curves, streaked spectra, space-resolved spectra, and drilldown plasma property plots, for an argon-doped capsule implosion experiment example. Future SpectraPLOT features and enhancements will also be discussed.

  15. BABAR - the detector for the PEP II B Factory at SLAC

    International Nuclear Information System (INIS)

    Lueth, V.

    1994-09-01

    BABAR refers to the detector that is being designed for the PEP II B-Factory at SLAC to perform a comprehensive study of CP violation in B meson decays. The design requirements and the principal detector components are briefly described. A summary of the expected physics performance is presented

  16. RF field control for KAON Factory booster cavities

    International Nuclear Information System (INIS)

    Craig, S.T.; de Jong, M.S.

    1990-11-01

    A conceptual design is developed for control of the KAON Factory Booster rf accelerating fields. This design addresses control of cavity: tuning, voltage amplitude, and voltage phase angle. Time-domain simulations were developed to evaluated the proposed controllers. These simulations indicated that adequate tuning performance can be obtained with the combination of adaptive feed-forward and proportional feedback control. Voltage amplitude and voltage phase can be adequately controlled using non-adaptive feedforward and proportional feedback control

  17. PCs in the factory

    CERN Document Server

    2013-01-01

    Please note this is a short discount publication.PCs have become as essential to the factory environment as they are to the office environment. This in-depth report examines how specially adapted PCs and peripherals are being established in Factory Process Control and Reporting. The report covers: * Hardware and Software* Typical Applications* Implementation Issues* Case Studies and Real Applications

  18. A novel design for sap flux data acquisition in large research plots using open source components

    Science.gov (United States)

    Hawthorne, D. A.; Oishi, A. C.

    2017-12-01

    Sap flux sensors are a widely-used tool for estimating in-situ, tree-level transpiration rates. These probes are installed in the stems of multiple trees within a study area and are typically left in place throughout the year. Sensors vary in their design and theory of operation, but all require electrical power for a heating element and produce at least one analog signal that must be digitized for storage. There are two topologies traditionally adopted to energize these sensors and gather the data from them. In one, a single data logger and power source are used. Dedicated cables radiate out from the logger to supply power to each of the probes and retrieve analog signals. In the other layout, a standalone data logger is located at each monitored tree. Batteries must then be distributed throughout the plot to service these loggers. We present a hybrid solution based on industrial control systems that employs a central data logger and battery, but co-locates digitizing hardware with the sensors at each tree. Each hardware node is able to communicate and share power over wire links with neighboring nodes. The resulting network provides a fault-tolerant path between the logger and each sensor. The approach is optimized to limit disturbance of the study plot, protect signal integrity and to enhance system reliability. This open-source implementation is built on the Arduino micro-controller system and employs RS485 and Modbus communications protocols. It is supported by laptop based management software coded in Python. The system is designed to be readily fabricated and programmed by non-experts. It works with a variety of sap-flux measurement techniques and it is able to interface to additional environmental sensors.

  19. Muon Colliders and Neutrino Factories

    Energy Technology Data Exchange (ETDEWEB)

    Kaplan, Daniel M. [IIT, Chicago

    2015-05-29

    Muon colliders and neutrino factories are attractive options for future facilities aimed at achieving the highest lepton-antilepton collision energies and precision measurements of Higgs boson and neutrino mixing matrix parameters. The facility performance and cost depend on how well a beam of muons can be cooled. Recent progress in muon cooling design studies and prototype tests nourishes the hope that such facilities could be built starting in the coming decade. The status of the key technologies and their various demonstration experiments is summarized. Prospects "post-P5" are also discussed.

  20. Preserving the Modernist Vertical Urban Factory

    Directory of Open Access Journals (Sweden)

    Nina Rappaport

    2016-07-01

    Full Text Available This essay is adapted in part, from the section, “Modern Factory Architecture” case studies from Nina Rappaport’s book Vertical Urban Factory, published by Actar this spring. Vertical Urban Factory began as an architecture studio, and then an exhibition, which opened in New York in 2011 and traveled to Detroit and Toronto in 2012. Last year the show was displayed at Archizoom at EPFL in Lausanne; Industry City, Brooklyn; and the Charles Moore School of Architecture at Kean University, in New Jersey. The project continues as a think tank evaluating factory futures and urban industrial potential.

  1. The B-factory project at KEK

    International Nuclear Information System (INIS)

    Kurokawa, Shin-ichi; Satoh, Kotaro

    1993-01-01

    The B-Factory project at KEK aims at constructing an accelerator complex which enables us to detect the CP-violation effect of B-mesons. It is a two-ring electron-positron collider of 3.5x8 GeV in the existing TRISTAN tunnel. The design peak luminosity is 10 34 cm -2 s -1 , which will be realized in two steps: from a small-angle collision with a luminosity of 2x10 33 cm -2 s -1 to a large-angle crab-crossing scheme with the final luminosity of 10 34 cm -2 s -1 . Progress of design work and present status of R and D are reported. (author)

  2. Participation of CUKROPROJEKT in the export of sugar factories in the years 1952-1972. I. [China

    Energy Technology Data Exchange (ETDEWEB)

    1973-01-01

    CUKROPROJEKT supervised the building of 2 beet sugar factories in the Chinese People's Republic. Work started in 1954 with preparation of the lay-out and the actual erection of the plant started in 1954. The plants in question were the sugar factories Chiamussy on the river Sungari and Sinjungo (New China) in Kirin, both with a daily capacity of 1000 t. Initial difficulties were overcome, the factories were put into operation in 1955 and the planned output was achieved. CUKROPROJEKT experts acquainted themselves with cane sugar processing and planned a design for a 3000 tons/day sugar factory with departments for production of absolute alcohol, fodder yeast, and solid CO/sub 2/. The factory was built in the Pearl River delta. Building operations started in 1957 and the factory started working in 1959. The planned output was achieved during the 1st campaign, with a peak throughput of 3600 tons/day.

  3. Plotting system for the MINCS code

    International Nuclear Information System (INIS)

    Watanabe, Tadashi

    1990-08-01

    The plotting system for the MINCS code is described. The transient two-phase flow analysis code MINCS has been developed to provide a computational tool for analysing various two-phase flow phenomena in one-dimensional ducts. Two plotting systems, namely the SPLPLOT system and the SDPLOT system, can be used as the plotting functions. The SPLPLOT system is used for plotting time transients of variables, while the SDPLOT system is for spatial distributions. The SPLPLOT system is based on the SPLPACK system, which is used as a general tool for plotting results of transient analysis codes or experiments. The SDPLOT is based on the GPLP program, which is also regarded as one of the general plotting programs. In the SPLPLOT and the SDPLOT systems, the standardized data format called the SPL format is used in reading data to be plotted. The output data format of MINCS is translated into the SPL format by using the conversion system called the MINTOSPL system. In this report, how to use the plotting functions is described. (author)

  4. Factorial structure of aerobics athletes’ fitness

    Directory of Open Access Journals (Sweden)

    T.V. Shepelenko

    2017-11-01

    Full Text Available The purpose of the research is to develop an algorithm of teams’ formation in sport aerobics and to define factorial structure of athletes’ fitness. Material : in the research sport aerobics’ athletes (n=19 participated. All athletes are members of Kharkiv national team (Ukraine. All athletes underwent complete medical examination. The functional condition of an organism (arterial blood pressure, indicators of a variability of the rhythm of the heart, treadbahn testing, psycho-physiological state (time’s determination of simple and complex reaction were defined. The physical development and physical fitness and stability of vestibular system were also defined. The factorial and cluster analysis were used. Results : The algorithm of teams’ formation in sport aerobics is developed for performances in various competitive categories. The algorithm contains all stages of standard procedure of the factorial and cluster analysis. In the factorial analysis the individual factorial values were also defined. Conclusions : The obtained data are recommended to be used at teams’ formation for performances in various competitive categories: team formation for pair and group performances. The general and individual factorial structure of athletes’ complex fitness is defined. It is possible to select athletes with similar qualities and with different qualities for the mixed performances. The determination of individual factorial structure of fitness permits to estimate objectively variants of athletes’ formation in groups.

  5. Dynamics of a split torque helicopter transmission

    Science.gov (United States)

    Krantz, Timothy L.

    1994-06-01

    Split torque designs, proposed as alternatives to traditional planetary designs for helicopter main rotor transmissions, can save weight and be more reliable than traditional designs. This report presents the results of an analytical study of the system dynamics and performance of a split torque gearbox that uses a balance beam mechanism for load sharing. The Lagrange method was applied to develop a system of equations of motion. The mathematical model includes time-varying gear mesh stiffness, friction, and manufacturing errors. Cornell's method for calculating the stiffness of spur gear teeth was extended and applied to helical gears. The phenomenon of sidebands spaced at shaft frequencies about gear mesh fundamental frequencies was simulated by modeling total composite gear errors as sinusoid functions. Although the gearbox has symmetric geometry, the loads and motions of the two power paths differ. Friction must be considered to properly evaluate the balance beam mechanism. For the design studied, the balance beam is not an effective device for load sharing unless the coefficient of friction is less than 0.003. The complete system stiffness as represented by the stiffness matrix used in this analysis must be considered to precisely determine the optimal tooth indexing position.

  6. IPLOT, interactive MELCOR data plotting system

    International Nuclear Information System (INIS)

    2008-01-01

    1 - Description of program or function: IPLOT is an interactive MELCOR data plotting system. It provides several kinds of GUI interfaces for a flexible data plotting. IPLOT capabilities include creation, saving and loading of user specified MELCOR variables trend graphs. IPLOT can use one or several plot files for a graph generation while the graphs can be either in one window or in several windows. Besides IPLOT provides several graph convenient functions such as zooming, re-sizing, printing for a detail analysis of severe accidents. 2 - Methods: Trend values seeking in a plot file is performed by a binary search method for fast performance. 3 - Restrictions on the complexity of the problem: MELCOR plot files are required for plotting

  7. Design of S-Band Phased Array Antenna with High Isolation Using Broadside Coupled Split Ring Resonator

    Directory of Open Access Journals (Sweden)

    Sungyoun Hwang

    2018-04-01

    Full Text Available In this paper, a method of designing a Vivaldi type phased array antenna (PAA which operates at S-band (2.8–3.3 GHz is presented. The presented antenna uses broadside coupled split ring resonators (BC-SRRs for high isolation, wide field of view, and good active S-parameter characteristics. As an example, we design a 1 × 8 array antenna with various BC-SRR structures using theory and EM simulations. The antenna is fabricated and measured to verify the design. With the BC-SRR implemented between the two radiating elements, the isolation is shown to be enhanced by 6 dB, up to 23 dB. The scan angle is shown to be within ±53° based on a −10 dB active reflection coefficient. The operation of the scan angle is possible within ±60° with a little larger reflection coefficient (−7 dB to −8 dB. The proposed design with BC-SRRs is expected to be useful for PAA applications.

  8. Tracking Changes in Cardiac Output: Statistical Considerations on the 4-Quadrant Plot and the Polar Plot Methodology.

    Science.gov (United States)

    Saugel, Bernd; Grothe, Oliver; Wagner, Julia Y

    2015-08-01

    When comparing 2 technologies for measuring hemodynamic parameters with regard to their ability to track changes, 2 graphical tools are omnipresent in the literature: the 4-quadrant plot and the polar plot recently proposed by Critchley et al. The polar plot is thought to be the more advanced statistical tool, but care should be taken when it comes to its interpretation. The polar plot excludes possibly important measurements from the data. The polar plot transforms the data nonlinearily, which may prevent it from being seen clearly. In this article, we compare the 4-quadrant and the polar plot in detail and thoroughly describe advantages and limitations of each. We also discuss pitfalls concerning the methods to prepare the researcher for the sound use of both methods. Finally, we briefly revisit the Bland-Altman plot for the use in this context.

  9. RF field control for Kaon Factory booster cavities

    International Nuclear Information System (INIS)

    Craig, S.T.; de Jong, M.S.

    1992-08-01

    A conceptual design is developed for control of the Kaon Factory booster rf accelerating fields. This design addresses control of cavity: tuning, voltage amplitude, and voltage phase angle. Time-domain simulations were developed to evaluate the proposed controllers. These simulations indicate that adequate tuning performance can be obtained with the combination of adaptive feed forward and proportional feedback control. Voltage amplitude and voltage phase can be adequately controlled using non-adaptive feed forward and proportional feedback control. (Author) (figs., tabs.)

  10. SigmaPlot 2000, Version 6.00, SPSS Inc. Computer Software Project Management, Requirements, and Design Document

    Energy Technology Data Exchange (ETDEWEB)

    HURLBUT, S.T.

    2000-10-24

    SigmaPlot is a vendor software product that will be used to convert the area under an absorbance curve generated by a Fourier transform infrared spectrometer (FTIR) to a relative area. SigmaPlot will be used in conjunction with procedure ZA-565-301, ''Determination of Moisture by Supercritical Fluid Extraction and Infrared Detection.''

  11. Batch phenol biodegradation study and application of factorial experimental design

    Directory of Open Access Journals (Sweden)

    A. Hellal

    2010-01-01

    Full Text Available A bacterium, Pseudomonas aeruginosa (ATTC27853, was investigated for its ability to grow and to degrade phenol as solecarbon source, in aerobic batch culture. The parameters which affect the substrate biodegradation such as the adaptation ofbacteria to phenol, the temperature, and the nature of the bacteria were investigated. The results show that for a range oftemperature of 30 to 40°C, the best degradation of phenol for a concentration of 100mg/l was observed at 30°C. The regenerationof the bacterium which allows the reactivation of its enzymatic activity, shows that the degradation of 100 mg/ l ofsubstrate at 30° C required approximately 50 hours with revivified bacteria, while it only starts after 72 hours for those norevivified. Adapted to increasing concentrations, allows the bacteria to degrade a substrate concentration of about 400mg/l in less than 350 hours.A second part was consisted in the determination of a substrate degradation model using the factorial experiment design,as a function of temperature (30-40°C and of the size of the inoculums (260.88 - 521.76mg/ l. The results were analyzedstatistically using the Student’s t-test, analysis of variance, and F-test. The value of R2 (0.99872 and adjusted R2 (0.9962close to 1.0, verifies the good correlation between the observed and the predicted values, and provides the excellent relationshipbetween the independent variables (factors and the response (the time of the phenol degradation. F-value found above200, indicates that the considered model is statistically significant.

  12. Normal probability plots with confidence.

    Science.gov (United States)

    Chantarangsi, Wanpen; Liu, Wei; Bretz, Frank; Kiatsupaibul, Seksan; Hayter, Anthony J; Wan, Fang

    2015-01-01

    Normal probability plots are widely used as a statistical tool for assessing whether an observed simple random sample is drawn from a normally distributed population. The users, however, have to judge subjectively, if no objective rule is provided, whether the plotted points fall close to a straight line. In this paper, we focus on how a normal probability plot can be augmented by intervals for all the points so that, if the population distribution is normal, then all the points should fall into the corresponding intervals simultaneously with probability 1-α. These simultaneous 1-α probability intervals provide therefore an objective mean to judge whether the plotted points fall close to the straight line: the plotted points fall close to the straight line if and only if all the points fall into the corresponding intervals. The powers of several normal probability plot based (graphical) tests and the most popular nongraphical Anderson-Darling and Shapiro-Wilk tests are compared by simulation. Based on this comparison, recommendations are given in Section 3 on which graphical tests should be used in what circumstances. An example is provided to illustrate the methods. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  13. Effect of a Preoperative Preparation Program on Anxiety in School-age Children Undergoing Surgery Using a Factorial Design

    Directory of Open Access Journals (Sweden)

    Maliheh Shoja

    2018-01-01

    Full Text Available Background: Surgery is a stressful experience in children. Therefore, the familiarization of this population with treatment processes by means of appropriate training tools and techniques can be an effective way to control their anxiety. Aim: The aim of this study was to determine the effect of a preoperative preparation program on anxiety in school-age children undergoing surgery using a factorial design. Method: This clinical trial was conducted on 81 children aged 6-12 years as candidates for elective surgery at Doctor Sheikh Hospital in Mashhad, Iran, in 2016. A preparation program was implemented with two methods (i.e., displaying video tutorials with and without nurses’ explanations and on two different days (i.e., prior to and on the day of operation using a factorial design. The estimation of children’s anxiety was accomplished by using the Revised Children’s Manifest Anxiety Scale administered before training and prior to operating room admission. The data were analyzed by statistical tests in SPSS software, version 16. Results: The study groups were comparable in terms of demographic characteristics (P>0.05. There was no significant differences among the four groups regarding manifest anxiety based on the place of referral (i.e., department or clinic (P=0.22, presentation or non-presentation of explanations by nurses (P=0.12, and their interaction effects (P=0.22. Implications for Practice: No significant difference was observed among the four groups in terms of manifest anxiety. Therefore, all four training methods were effective in reducing anxiety in children. Consequently, each of these methods can be used depending on human resources and infrastructure of each department.

  14. Status of the SLAC/LBL/LLNL B-Factory and the BaBar detector

    International Nuclear Information System (INIS)

    Oddone, P.

    1994-08-01

    The primary motivation of the Asymmetric B-Factory is the study of CP violation. The decay of B mesons and, in particular, the decay of neutral B mesons, offers the possibility of determining conclusively whether CP violation is part and parcel of the Standard Model with three generations of quarks and leptons. Alternatively, the authors may discover that CP violation lies outside the present framework. In this paper the authors briefly describe the physics reach of the SLAC/LBL/LLNL Asymmetric B-Factory, the progress on the machine design and construction, the progress on the detector design, and the schedule to complete both projects

  15. Splitting methods for split feasibility problems with application to Dantzig selectors

    International Nuclear Information System (INIS)

    He, Hongjin; Xu, Hong-Kun

    2017-01-01

    The split feasibility problem (SFP), which refers to the task of finding a point that belongs to a given nonempty, closed and convex set, and whose image under a bounded linear operator belongs to another given nonempty, closed and convex set, has promising applicability in modeling a wide range of inverse problems. Motivated by the increasingly data-driven regularization in the areas of signal/image processing and statistical learning, in this paper, we study the regularized split feasibility problem (RSFP), which provides a unified model for treating many real-world problems. By exploiting the split nature of the RSFP, we shall gainfully employ several efficient splitting methods to solve the model under consideration. A remarkable advantage of our methods lies in their easier subproblems in the sense that the resulting subproblems have closed-form representations or can be efficiently solved up to a high precision. As an interesting application, we apply the proposed algorithms for finding Dantzig selectors, in addition to demonstrating the effectiveness of the splitting methods through some computational results on synthetic and real medical data sets. (paper)

  16. Generalized Probability-Probability Plots

    NARCIS (Netherlands)

    Mushkudiani, N.A.; Einmahl, J.H.J.

    2004-01-01

    We introduce generalized Probability-Probability (P-P) plots in order to study the one-sample goodness-of-fit problem and the two-sample problem, for real valued data.These plots, that are constructed by indexing with the class of closed intervals, globally preserve the properties of classical P-P

  17. Influence of core design, production technique, and material selection on fracture behavior of yttria-stabilized tetragonal zirconia polycrystal fixed dental prostheses produced using different multilayer techniques: split-file, over-pressing, and manually built-up veneers.

    Science.gov (United States)

    Mahmood, Deyar Jallal Hadi; Linderoth, Ewa H; Wennerberg, Ann; Vult Von Steyern, Per

    2016-01-01

    To investigate and compare the fracture strength and fracture mode in eleven groups of currently, the most commonly used multilayer three-unit all-ceramic yttria-stabilized tetragonal zirconia polycrystal (Y-TZP) fixed dental prostheses (FDPs) with respect to the choice of core material, veneering material area, manufacturing technique, design of connectors, and radii of curvature of FDP cores. A total of 110 three-unit Y-TZP FDP cores with one intermediate pontic were made. The FDP cores in groups 1-7 were made with a split-file design, veneered with manually built-up porcelain, computer-aided design-on veneers, and over-pressed veneers. Groups 8-11 consisted of FDPs with a state-of-the-art design, veneered with manually built-up porcelain. All the FDP cores were subjected to simulated aging and finally loaded to fracture. There was a significant difference (Pdesigns, but not between the different types of Y-TZP materials. The split-file designs with VITABLOCS(®) (1,806±165 N) and e.max(®) ZirPress (1,854±115 N) and the state-of-the-art design with VITA VM(®) 9 (1,849±150 N) demonstrated the highest mean fracture values. The shape of a split-file designed all-ceramic reconstruction calls for a different dimension protocol, compared to traditionally shaped ones, as the split-file design leads to sharp approximal indentations acting as fractural impressions, thus decreasing the overall strength. The design of a framework is a crucial factor for the load bearing capacity of an all-ceramic FDP. The state-of-the-art design is preferable since the split-file designed cores call for a cross-sectional connector area at least 42% larger, to have the same load bearing capacity as the state-of-the-art designed cores. All veneering materials and techniques tested in the study, split-file, over-press, built-up porcelains, and glass-ceramics are, with a great safety margin, sufficient for clinical use both anteriorly and posteriorly. Analysis of the fracture pattern shows

  18. Colorful Microbial Cell Factories

    DEFF Research Database (Denmark)

    Petersen, Pia Damm

    Yeast cell factories are powerful tools used for the production of high-value natural compounds otherwise not easily available. Many bioactive and industrially important plant secondary metabolites can be produced in yeast by engineering their biosynthetic pathways into yeast cells, as these both...... anthocyanins. Yeast cell factories present a platform to circumvent the problem of low yields of interesting molecular structures in plant tissues, as hand-picking of desired enzyme activities allows for specific biosynthesis of the precise pigment of interest, as well as choosing more stable structures...... for heterologous biosynthesis is possible. In cell factories, great improvements in yields can be achieved through molecular engineering of flux from endogenous yeast precursors, e.g. by elimination of by-product formation, and by genetic optimization of pathway components, such as fine-tuning of expression levels...

  19. The Brazilian national system of forest permanent plots

    Science.gov (United States)

    Yeda Maria Malheiros de Oliveira; Maria Augusta Doetzer Rosot; Patricia Povoa de Mottos; Joberto Veloso de Freitas; Guilherme Luis Augusto Gomide; < i> et al< /i>

    2009-01-01

    The Brazilian National System of Forest Permanent Plots (SisPP) is a governmental initiative designed and being implemented in partnership by the Ministry of Environment (MMA), represented by the National Forest Programme (PNF) and the Brazilian Forest Service (SFB) and the Embrapa Forestry (a research center of the Brazilian Agricultural Research Corporation - Embrapa...

  20. Yield and nutritional efficiency of corn in response to rates and splits of nitrogen fertilization

    Directory of Open Access Journals (Sweden)

    Telmo Jorge Carneiro Amado

    Full Text Available ABSTRACT Despite its relevance, nitrogen is poorly utilized by the plants when improperly applied. Thus, the objective of this study was to evaluate the yield and nitrogen use efficiency (NUE in corn in response to doses and split application of nitrogen fertilization. The experimental design was a randomized block design, with three replications. Doses of nitrogen of 0, 30, 60 and 180 kg ha-1 were applied at sowing in order to create different nutritional status of corn plants and to obtain different values of Normalized Difference Vegetation Index (NDVI measured with “Greenseeker®” optical sensor. The subplots with nitrogen doses in topdressing of 0, 30, 60 and 90 kg ha-1 at V8 and a dose of 60 kg ha-1 at V12 were placed in experimental plots with doses of 0, 30, 60 and 180 kg ha-1 of nitrogen at sowing. Moreover, NUE was calculated in the experiment using agronomic indexes determined by applications of nitrogen in late topdressing (V8 and V12 and contrasted to the possible combinations at doses of 60, 90 and 120 kg ha-1 of total N applied. The results showed the occurrence of a linear relationship between nitrogen fertilizer dose and NDVI at V8 as well as at V12 stages. Late topdressing fertilizations (V12 did not cause a decrease in grain yield when combined with nitrogen fertilization at sowing, moreover resulted in higher NUE. Split the nitrogen dose showed better NUE than the combinations where nitrogen was not applied at sowing or in topdressing. The delay of nitrogen topdressing can be an alternative for the planning of the moment of the N fertilization according to the climate forecast in each region.

  1. Split-Framework in Mandibular Implant-Supported Prosthesis

    Directory of Open Access Journals (Sweden)

    Danny Omar Mendoza Marin

    2015-01-01

    Full Text Available During oral rehabilitation of an edentulous patient with an implant-supported prosthesis, mandibular flexure must be considered an important biomechanical factor when planning the metal framework design, especially if implants are installed posterior to the interforaminal region. When an edentulous mandible is restored with a fixed implant-supported prosthesis connected by a fixed full-arch framework, mandibular flexure may cause needless stress in the overall restorative system and lead to screw loosening, poor fit of prosthesis, loss of the posterior implant, and patient’s discomfort due to deformation properties of the mandible during functional movements. The use of a split-framework could decrease the stress with a precise and passive fit on the implants and restore a more natural functional condition of the mandible, helping in the longevity of the prosthesis. Therefore, the present clinical report describes the oral rehabilitation of an edentulous patient by a mandibular fixed implant-supported prosthesis with a split-framework to compensate for mandibular flexure. Clinical Significance. The present clinical report shows that the use of a split-framework reduced the risk of loss of the posterior implants or screws loosening with acceptable patient comfort over the period of a year. The split-framework might have compensated for the mandibular flexure during functional activities.

  2. Evaluation of the influence of base and alkyl bromide on synthesis of pyrazinoic acid esters through factorial design

    International Nuclear Information System (INIS)

    Fernandes, Joao Paulo dos Santos; Felli, Veni Maria Andres

    2009-01-01

    Pyrazinoic acid esters have been synthesized as prodrugs of pyrazinoic acid. In the literature, its preparation is reported through the reaction of pyrazinoyl chloride with alcohols and the reaction with DCC/DMAP. In this work, it is reported a 22 factorial design to evaluate the preparation of these esters through the substitution of alkyl bromides with carboxylate anion. The controlled factors were alkyl chain length of bromides (ethyl and hexyl) and the used base (triethylamine and DBU). Results revealed that the used base used has significant effect on yield, and alkyl bromide used has neither significant influence, nor its interaction effect with base. (author)

  3. Study of flow behaviors of droplet merging and splitting in microchannels using Micro-PIV measurement

    Science.gov (United States)

    Li, Yi; Liu, Zhaomiao

    2017-01-01

    Droplet merging and splitting are important droplet manipulations in droplet-based microfluidics. However, the fundamental flow behaviors of droplets were not systematically studied. Hence, we designed two different microstructures to achieve droplet merging and splitting respectively, and quantitatively compared different flow dynamics in different microstructures for droplet merging and splitting via micro-particle image velocimetry (micro-PIV) experiments. Some flow phenomena of droplets different from previous studies were observed during merging and splitting using a high-speed microscope. It was also found the obtained instantaneous velocity vector fields of droplets have significant influence on the droplets merging and splitting. For droplet merging, the probability of droplets coalescence (η) in a microgroove is higher (50% T-junction microchannel (15% < η < 50%), and the highest coalescence efficiency (η = 92%) comes at the two-phase flow ratio e of 0.42 in the microgroove. Moreover, compared with a cylinder obstacle, Y-junction bifurcation can split droplets more effectively and the droplet flow during splitting is steadier. The results can provide better understanding of droplet behaviors and are useful for the design and applications of droplet-based microfluidics. PMID:28890680

  4. Study of flow behaviors of droplet merging and splitting in microchannels using Micro-PIV measurement.

    Science.gov (United States)

    Shen, Feng; Li, Yi; Liu, Zhaomiao; Li, XiuJun

    2017-04-01

    Droplet merging and splitting are important droplet manipulations in droplet-based microfluidics. However, the fundamental flow behaviors of droplets were not systematically studied. Hence, we designed two different microstructures to achieve droplet merging and splitting respectively, and quantitatively compared different flow dynamics in different microstructures for droplet merging and splitting via micro-particle image velocimetry (micro-PIV) experiments. Some flow phenomena of droplets different from previous studies were observed during merging and splitting using a high-speed microscope. It was also found the obtained instantaneous velocity vector fields of droplets have significant influence on the droplets merging and splitting. For droplet merging, the probability of droplets coalescence ( η ) in a microgroove is higher (50% < η < 92%) than that in a T-junction microchannel (15% < η < 50%), and the highest coalescence efficiency ( η = 92%) comes at the two-phase flow ratio e of 0.42 in the microgroove. Moreover, compared with a cylinder obstacle, Y-junction bifurcation can split droplets more effectively and the droplet flow during splitting is steadier. The results can provide better understanding of droplet behaviors and are useful for the design and applications of droplet-based microfluidics.

  5. Persuasive Technology for Learning and Teaching – The EuroPLOT Project

    OpenAIRE

    Behringer, R; Soosay, M; Gram-Hansen, SB; Øhrstrøm, P; Sørensen, CG; Smith, C; Mikulecká, J; Winther-Nielsen, N; Winther-Nielsen, M; Herber, E

    2013-01-01

    The concept of persuasive design has demonstrated its benefits by changing human behavior in certain situations, but in the area of education and learning, this approach has rarely been used. To change this and to study the feasibility of persuasive technology in teaching and learning, the EuroPLOT project (PLOT = Persuasive Learning Objects and Technologies) has been funded 2010-2013 by the Education, Audiovisual and Culture Executive Agency (EACEA) in the Life-long Learning (LLL) programme....

  6. Interaction region considerations for a B-factory

    International Nuclear Information System (INIS)

    DeStaebler, H.

    1990-07-01

    The goal of the project is to observe CP violation in the bar BB system. This machine is supposed to be a factory for high energy physics, not an R ampersand D project for accelerator physics. There are a number of interrelated design issues arising from the different desires of the detector and the machine, some of which are listed in this paper. A number of background and beampipe issues are mentioned. The emphasis is on calculations. Any satisfactory design will combine measurements on existing machines with calculations pertaining to the measurement conditions as well as to the proposed machine. 57 refs

  7. Design Expert Supported Mathematical Optimization and Predictability Study of Buccoadhesive Pharmaceutical Wafers of Loratadine

    Directory of Open Access Journals (Sweden)

    Prithviraj Chakraborty

    2013-01-01

    Full Text Available Objective. The objective of this work encompasses the application of the response surface approach in the development of buccoadhesive pharmaceutical wafers of Loratadine (LOR. Methods. Experiments were performed according to a 32 factorial design to evaluate the effects of buccoadhesive polymer, sodium alginate (A, and lactose monohydrate as ingredient, of hydrophilic matrix former (B on the bioadhesive force, disintegration time, percent (% swelling index, and time taken for 70% drug release (t70%. The effect of the two independent variables on the response variables was studied by response surface plots and contour plots generated by the Design-Expert software. The desirability function was used to optimize the response variables. Results. The compatibility between LOR and the wafer excipients was confirmed by differential scanning calorimetry, FTIR spectroscopy, and X-ray diffraction (XRD analysis. Bioadhesion force, measured with TAXT2i texture analyzer, showed that the wafers had a good bioadhesive property which could be advantageous for retaining the drug into the buccal cavity. Conclusion. The observed responses taken were in agreement with the experimental values, and Loratadine wafers were produced with less experimental trials, and a patient compliant product was achieved with the concept of formulation by design.

  8. Design Expert Supported Mathematical Optimization and Predictability Study of Buccoadhesive Pharmaceutical Wafers of Loratadine

    Science.gov (United States)

    Dey, Surajit; Parcha, Versha; Bhattacharya, Shiv Sankar; Ghosh, Amitava

    2013-01-01

    Objective. The objective of this work encompasses the application of the response surface approach in the development of buccoadhesive pharmaceutical wafers of Loratadine (LOR). Methods. Experiments were performed according to a 32 factorial design to evaluate the effects of buccoadhesive polymer, sodium alginate (A), and lactose monohydrate as ingredient, of hydrophilic matrix former (B) on the bioadhesive force, disintegration time, percent (%) swelling index, and time taken for 70% drug release (t 70%). The effect of the two independent variables on the response variables was studied by response surface plots and contour plots generated by the Design-Expert software. The desirability function was used to optimize the response variables. Results. The compatibility between LOR and the wafer excipients was confirmed by differential scanning calorimetry, FTIR spectroscopy, and X-ray diffraction (XRD) analysis. Bioadhesion force, measured with TAXT2i texture analyzer, showed that the wafers had a good bioadhesive property which could be advantageous for retaining the drug into the buccal cavity. Conclusion. The observed responses taken were in agreement with the experimental values, and Loratadine wafers were produced with less experimental trials, and a patient compliant product was achieved with the concept of formulation by design. PMID:23781498

  9. Micro Tools with Pneumatic Actuators for Desktop Factories

    Directory of Open Access Journals (Sweden)

    Björn HOXHOLD

    2009-10-01

    Full Text Available This paper presents the design, the simulation and the fabrication process of two novel pneumatically driven auxiliary micro tools that can be used to improve and to speed up assembling processes in desktop factories. The described micro systems are designed to function as centrifugal feeders for small glass balls or active clamping devices with small external dimensions. They are able to deliver more than six balls per second on demand to a gripper and align and clamp single chips in a fixed position.

  10. Construction of an experimental plot seeder of wheat planting and compare it by imported one

    Directory of Open Access Journals (Sweden)

    I Eskandari

    2016-09-01

    Full Text Available Introduction Researchers frequently include multiple cultivars and fertility levels in field experiments. Therefore, the experiments sowing operation must represent a considerable saving in time and labor, compared to hand sowing. Greater flexibility in experimental design and setup could be achieved by equipment that enables quick changes in the cultivar and fertilizer rates from one plot to the next. A satisfactory seed drill must distribute a given quantity of seed evenly over a predetermined length of coulter row, the coulters must be spaced at exact intervals and depth of sowing must be uniform. In a self-propelled type of plot seeder, no coulter should run in a wheel track as the compaction of the soil can cause observable differences in vigor between plants in such a row and those in un-compacted rows. The machine should sow in succession from a try in which a series of seed pocket separated clearly and must be put into distributer funnel by an assistant operator. The length of gap being varied according to the nature and purpose of the plot. The objectives of this experiment were 1- to design and construct a local self-propelled plot seeder and 2- To compare it with the imported (Wintersteiger plot seeder in cereal breeding programs. Materials and Methods A small-plot seeder was designed and constructed to meet this objective. The unit consists of the following basic components: a toolbar for pulling a set of six blade coulter, an air compressor for lifting and putting down the openers and metering transmission drive wheel, an operators chair and work rack, one belt seed distribution. A cone-celled and rotor seed distributor is used for seed distribution to the openers. The cone system is connected to the gearbox and allows for great flexibility in changing cultivars, crop species, and plot length. This is driven by the separate drive wheel. The cone-celled distributor sows all the seed of the sample in making one complete turn. The

  11. FLOWCHART; a computer program for plotting flowcharts

    Science.gov (United States)

    Bender, Bernice

    1982-01-01

    The computer program FLOWCHART can be used to very quickly and easily produce flowcharts of high quality for publication. FLOWCHART centers each element or block of text that it processes on one of a set of (imaginary) vertical lines. It can enclose a text block in a rectangle, circle or other selected figure. It can draw a 'line connecting the midpoint of any side of any figure with the midpoint of any side of any other figure and insert an arrow pointing in the direction of flow. It can write 'yes' or 'no' next to the line joining two figures. FLOWCHART creates flowcharts using some basic plotting subroutine* which permit plots to be generated interactively and inspected on a Tektronix compatible graphics screen or plotted in a deferred mode on a Houston Instruments 42' pen plotter. The size of the plot, character set and character height in inches are inputs to the program. Plots generated using the pen plotter can be up to 42' high--the larger size plots being directly usable as visual aids in a talk. FLOWCHART centers each block of text on an imaginary column line. (The number of columns and column width are specified as input.) The midpoint of the longest line of text within the block is defined to be the center of the block and is placed on the column line. The spacing of individual words within the block is not altered when the block is positioned. The program writes the first block of text in a designated column and continues placing each subsequent block below the previous block in the same column. A block of text may be placed in a different column by specifying the number of the column and an earlier block of text with which the new block is to be aligned. If block zero is given as the earlier block, the new text is placed in the new column continuing down the page below the previous block. Optionally a column and number of inches from the top of the page may be given for positioning the next block of text. The program will normally draw one of five

  12. Gas turbine designer computer program - a study of using a computer for preliminary design of gas turbines

    Energy Technology Data Exchange (ETDEWEB)

    Petersson, Rickard

    1995-11-01

    This thesis presents calculation schemes and theories for preliminary design of the fan, high pressure compressor and turbine of a gas turbine. The calculations are presented step by step, making it easier to implement in other applications. The calculation schemes have been implemented as a subroutine in a thermodynamic program. The combination of the thermodynamic cycle calculation and the design calculation turned out to give quite relevant results, when predicting the geometry and performance of an existing aero engine. The program developed is able to handle several different gas turbines, including those in which the flow is split (i.e. turbofan engines). The design process is limited to the fan, compressor and turbine of the gas turbine, the rest of the components have not been considered. Output from the program are main geometry, presented both numerically and as a scale plot, component efficiencies, stresses in critical points and a simple prediction of turbine blade temperatures. 11 refs, 21 figs, 1 tab

  13. Advanced Envelope Research for Factory Built Housing, Phase 3. Whole-House Prototyping

    Energy Technology Data Exchange (ETDEWEB)

    Levy, E. [Advanced Residential Integrated Energy Solutions (ARIES), New York, NY (United States); Mullens, M. [Advanced Residential Integrated Energy Solutions (ARIES), New York, NY (United States); Rath, P. [Advanced Residential Integrated Energy Solutions (ARIES), New York, NY (United States)

    2014-04-01

    The Advanced Envelope Research effort will provide factory homebuilders with high performance, cost-effective envelope designs that can be effectively integrated into the plant production process while meeting the thermal requirements of the 2012 IECC standards. This work is part of a multiphase effort. Phase 1 identified seven envelope technologies and provided a preliminary assessment of three methods for building high performance walls. Phase 2 focused on developing viable product designs, manufacturing strategies, addressing code and structural issues, and cost analysis of the three selected options. An industry advisory committee helped narrow the research focus to perfecting a stud wall design with exterior continuous insulation (CI). This report describes Phase 3, which was completed in two stages and continued the design development effort, exploring and evaluating a range or methods for applying CI to factory built homes. The scope also included material selection, manufacturing and cost analysis, and prototyping and testing. During this phase, a home was built with CI, evaluated, and placed in service. The experience of building a mock up wall section with CI and then constructing on line a prototype home resolved important concerns about how to integrate the material into the production process. First steps were taken toward finding least expensive approaches for incorporating CI in standard factory building practices and a preliminary assessment suggested that even at this early stage the technology is attractive when viewed from a life cycle cost perspective.

  14. Information security of Smart Factories

    Science.gov (United States)

    Iureva, R. A.; Andreev, Y. S.; Iuvshin, A. M.; Timko, A. S.

    2018-05-01

    In several years, technologies and systems based on the Internet of things (IoT) will be widely used in all smart factories. When processing a huge array of unstructured data, their filtration and adequate interpretation are a priority for enterprises. In this context, the correct representation of information in a user-friendly form acquires special importance, for which the market today presents advanced analytical platforms designed to collect, store and analyze data on technological processes and events in real time. The main idea of the paper is the statement of the information security problem in IoT and integrity of processed information.

  15. Accelerated and Rational Design of Improved CHO Cell Factories

    DEFF Research Database (Denmark)

    Grav, Lise Marie

    Recombinant production of therapeutic proteins provides huge benefits to human health and promises solutions to some of the most devastating and currently untreatable diseases in healthcare. Key to the development of new therapeutic proteins is to optimize and engineer living cells, namely cell...... of a number of novel tools is reported that aim to accelerate the construction of production cell lines for therapeutic proteins with optimal phenotypic attributes for industrial processes. Chinese hamster ovary (CHO) cells are the predominant production host for therapeutic proteins, and are the cell factory...... of interest in this thesis. The core of the thesis is revolved around the development and application of genome editing techniques that enable us to precisely engineer the genome of CHO cells by either rendering specific-targeted genes unfunctional or inserting new genes in precise genomic locations...

  16. Promoting contraceptive use among unmarried female migrants in one factory in Shanghai: a pilot workplace intervention.

    Science.gov (United States)

    Qian, Xu; Smith, Helen; Huang, Wenyuan; Zhang, Jie; Huang, Ying; Garner, Paul

    2007-05-31

    In urban China, more single women are becoming pregnant and resorting to induced abortion, despite the wide availability of temporary methods of contraception. We developed and piloted a workplace-based intervention to promote contraceptive use in unmarried female migrants working in privately owned factories. Quasi-experimental design. In consultation with clients, we developed a workplace based intervention to promote contraception use in unmarried female migrants in a privately owned factory. We then implemented this in one factory, using a controlled before-and-after design. The intervention included lectures, bespoke information leaflets, and support to the factory doctors in providing a contraceptive service. 598 women participated: most were under 25, migrants to the city, with high school education. Twenty percent were lost when staff were made redundant, and implementation was logistically complicated. All women attended the initial lecture, and just over half the second lecture. Most reported reading the educational material provided (73%), but very few women reported using the free family planning services offered at the factory clinic (5%) or the Family Planning Institute (3%). At baseline, 90% (N = 539) stated that contraceptives were required if having sex before marriage; of those reporting sex in the last three months, the majority reporting using contraceptives (78%, 62/79) but condom use was low (44%, 35/79). Qualitative data showed that the reading material seemed to be popular and young women expressed a need for more specific reproductive health information, particularly on HIV/AIDS. Women wanted services with some privacy and anonymity, and views on the factory service were mixed. Implementing a complex intervention with a hard to reach population through a factory in China, using a quasi-experimental design, is not easy. Further research should focus on the specific needs and service preferences of this population and these should be

  17. Promoting contraceptive use among unmarried female migrants in one factory in Shanghai: a pilot workplace intervention

    Directory of Open Access Journals (Sweden)

    Qian Xu

    2007-05-01

    Full Text Available Abstract Background In urban China, more single women are becoming pregnant and resorting to induced abortion, despite the wide availability of temporary methods of contraception. We developed and piloted a workplace-based intervention to promote contraceptive use in unmarried female migrants working in privately owned factories. Methods Quasi-experimental design. In consultation with clients, we developed a workplace based intervention to promote contraception use in unmarried female migrants in a privately owned factory. We then implemented this in one factory, using a controlled before-and-after design. The intervention included lectures, bespoke information leaflets, and support to the factory doctors in providing a contraceptive service. Results 598 women participated: most were under 25, migrants to the city, with high school education. Twenty percent were lost when staff were made redundant, and implementation was logistically complicated. All women attended the initial lecture, and just over half the second lecture. Most reported reading the educational material provided (73%, but very few women reported using the free family planning services offered at the factory clinic (5% or the Family Planning Institute (3%. At baseline, 90% (N = 539 stated that contraceptives were required if having sex before marriage; of those reporting sex in the last three months, the majority reporting using contraceptives (78%, 62/79 but condom use was low (44%, 35/79. Qualitative data showed that the reading material seemed to be popular and young women expressed a need for more specific reproductive health information, particularly on HIV/AIDS. Women wanted services with some privacy and anonymity, and views on the factory service were mixed. Conclusion Implementing a complex intervention with a hard to reach population through a factory in China, using a quasi-experimental design, is not easy. Further research should focus on the specific needs and

  18. Desarrollo vegetativo de patrones cítricos cultivados en condiciones de invernadero bajo dos sistemas de riego Vegetative development of citrus seedlings cultivated at greenhouse conditions and submitted to two irrigations systems

    Directory of Open Access Journals (Sweden)

    Gilmar Schäfer

    2006-08-01

    Full Text Available En el presente estudio se evaluó el desarrollo vegetativo de patrones cítricos cultivados en invernadero bajo dos sistemas de riego. El experimento se realizó en la Estação Experimental Agronômica de la Universidade Federal do Rio Grande do Sul, ubicada en Eldorado do Sul, Rio Grande do Sul, Brasil, entre los meses de septiembre de 2003 y abril de 2004, totalizando 225 días de experimentación. El diseño experimental fue de parcelas subdivididas, en factorial 2 x 3, con 4 repeticiones de 22 contenedores cada. En las parcelas principales se evaluaron los sistemas de riego (microaspersión y capilaridad y en las subparcelas los patrones cítricos Poncirus trifoliata (L. Raf., citrangero 'C37' [P. trifoliata x Citrus sinensis (L. Osb. cv. Pêra] y lima 'Rangpur' (C. limonia Osb.. En condiciones de invernadero los patrones cítricos presentan un desarrollo vegetativo más rápido bajo riego por capilaridad respecto a la microaspersión. Los patrones cítricos evaluados presentan desarrollos vegetativos distintos, donde el citrangero 'C37' supera a los demás.The aim of the present work was to evaluate the vegetative development of citrus rootstock seedlings cultivated under greenhouse conditions with two irrigation systems. The experiment was conducted at the Estação Experimental Agronômica , Universidade Federal do Rio Grande do Sul, located in Eldorado do Sul, Rio Grande do Sul, Brazil, from September 2003 to April 2004, totalizing 225 days of experimentation. The experimental design was a split-plot, in a 2x3 factorial, with 4 replications of 22 pots each. In the main plot the irrigation systems was evaluated (micro sprinkler and capillarity and in the split-plot the citrus rootstocks [Trifoliate orange - Poncirus trifoliata (L. Raf., 'C37' citrange - P. trifoliata x Citrus sinensis (L. Osb. cv. Pêra and 'Rangpur' lime - C. limonia Osb.] were evaluated. The main result showed in conditions of greenhouse citrus rootstock seedlings

  19. Modelling of uranium/plutonium splitting in purex process

    International Nuclear Information System (INIS)

    Boullis, B.; Baron, P.

    1987-06-01

    A mathematical model simulating the highly complex uranium/plutonium splitting operation in PUREX process has been achieved by the french ''Commissariat a l'Energie Atomique''. The development of such a model, which includes transfer and redox reactions kinetics for all the species involved, required an important experimental work in the field of basis chemical data acquisition. The model has been successfully validated by comparison of its results with those of specific trials achieved (at laboratory scale), and with the available results of the french reprocessing units operation. It has then been used for the design of french new plants splitting operations

  20. Evaluation of Mandibular Anatomy Associated With Bad Splits in Sagittal Split Ramus Osteotomy of Mandible.

    Science.gov (United States)

    Wang, Tongyue; Han, Jeong Joon; Oh, Hee-Kyun; Park, Hong-Ju; Jung, Seunggon; Park, Yeong-Joon; Kook, Min-Suk

    2016-07-01

    This study aimed to identify risk factors associated with bad splits during sagittal split ramus osteotomy by using three-dimensional computed tomography. This study included 8 bad splits and 47 normal patients without bad splits. Mandibular anatomic parameters related to osteotomy line were measured. These included anteroposterior width of the ramus at level of lingula, distance between external oblique ridge and lingula, distance between sigmoid notch and inferior border of mandible, mandibular angle, distance between inferior outer surface of mandibular canal and inferior border of mandible under distal root of second molar (MCEM), buccolingual thickness of the ramus at level of lingula, and buccolingual thickness of the area just distal to first molar (BTM1) and second molar (BTM2). The incidence of bad splits in 625 sagittal split osteotomies was 1.28%. Compared with normal group, bad split group exhibited significantly thinner BTM2 and shorter sigmoid notch and inferior border of mandible (P bad splits. These anatomic data may help surgeons to choose the safest surgical techniques and best osteotomy sites.

  1. Muon front end for the neutrino factory

    CERN Document Server

    Rogers, C T; Prior, G; Gilardoni, S; Neuffer, D; Snopok, P; Alekou, A; Pasternak, J

    2013-01-01

    In the neutrino factory, muons are produced by firing high-energy protons onto a target to produce pions. The pions decay to muons and pass through a capture channel known as the muon front end, before acceleration to 12.6 GeV. The muon front end comprises a variable frequency rf system for longitudinal capture and an ionization cooling channel. In this paper we detail recent improvements in the design of the muon front end.

  2. A review of metabolic and enzymatic engineering strategies for designing and optimizing performance of microbial cell factories

    Directory of Open Access Journals (Sweden)

    Amanda K. Fisher

    2014-08-01

    Full Text Available Microbial cell factories (MCFs are of considerable interest to convert low value renewable substrates to biofuels and high value chemicals. This review highlights the progress of computational models for the rational design of an MCF to produce a target bio-commodity. In particular, the rational design of an MCF involves: (i product selection, (ii de novo biosynthetic pathway identification (i.e., rational, heterologous, or artificial, (iii MCF chassis selection, (iv enzyme engineering of promiscuity to enable the formation of new products, and (v metabolic engineering to ensure optimal use of the pathway by the MCF host. Computational tools such as (i de novo biosynthetic pathway builders, (ii docking, (iii molecular dynamics (MD and steered MD (SMD, and (iv genome-scale metabolic flux modeling all play critical roles in the rational design of an MCF. Genome-scale metabolic flux models are of considerable use to the design process since they can reveal metabolic capabilities of MCF hosts. These can be used for host selection as well as optimizing precursors and cofactors of artificial de novo biosynthetic pathways. In addition, recent advances in genome-scale modeling have enabled the derivation of metabolic engineering strategies, which can be implemented using the genomic tools reviewed here as well.

  3. Fifth International Symposium on Recurrence Plot

    CERN Document Server

    Riley, Michael; Giuliani, Alessandro; Webber, Charles; Jr, Jr; Translational Recurrences : From Mathematical Theory to Real-World Applications

    2014-01-01

    This book features 13 papers presented at the Fifth International Symposium on Recurrence Plots, held August 2013 in Chicago, IL. It examines recent applications and developments in recurrence plots and recurrence quantifi cation analysis (RQA) with special emphasis on biological and cognitive systems and the analysis of coupled systems using cross-recurrence methods. Readers will discover new applications and insights into a range of systems provided by recurrence plot analysis and new theoretical and mathematical developments in recurrence plots. Recurrence plot based analysis is a powerful tool that operates on real-world complex systems that are nonlinear, non-stationary, noisy, of any statistical distribution, free of any particular model type, and not particularly long. Quantitative analyses promote the detection of system state changes, synchronized dynamical regimes, or classifi cation of system states. Th e book will be of interest to an interdisciplinary audience of recurrence plot users and researc...

  4. A first look at measurement error on FIA plots using blind plots in the Pacific Northwest

    Science.gov (United States)

    Susanna Melson; David Azuma; Jeremy S. Fried

    2002-01-01

    Measurement error in the Forest Inventory and Analysis work of the Pacific Northwest Station was estimated with a recently implemented blind plot measurement protocol. A small subset of plots was revisited by a crew having limited knowledge of the first crew's measurements. This preliminary analysis of the first 18 months' blind plot data indicates that...

  5. deltaPlotR: An R Package for Di?erential Item Functioning Analysis with Ango? s Delta Plot

    OpenAIRE

    David Magis; Bruno Facon

    2014-01-01

    Angoff's delta plot is a straightforward and not computationally intensive method to identify differential item functioning (DIF) among dichotomously scored items. This approach was recently improved by proposing an optimal threshold selection and by considering several item purification processes. Moreover, to support practical DIF analyses with the delta plot and these improvements, the R package deltaPlotR was also developed. The purpose of this paper is twofold: to outline the delta plot ...

  6. Shielding design of RIKEN RI Beam Factory

    Energy Technology Data Exchange (ETDEWEB)

    Uwamino, Yoshitomo; Fukunishi, Nobuhisa [Institute of Physical and Chemical Research, Wako, Saitama (Japan); Oishi, Koji [Shimizu Corp., Tokyo (Japan)

    2000-03-01

    Construction of the RIKEN RI Beam Factory is started, and the phase 1 will be finished by the end of March 2003. Two ring cyclotrons including one superconducting machine and two Big RIPSs will be constructed in the phase 1. Heavy ions of proton to uranium will be accelerated up to 400 MeV/u (A<40) and 150 MeV/u for uranium at an intensity of 10{sup 13} pps. Neutron production by the 400 MeV/u {sup 20}Ne beam was measured at HIMAC of NIRS and it was used for the source term of the shielding calculations. The deep penetration of high-energy neutrons was calculated by using the ANISN code with the DLC-119/HILO86R group constants and also by using the HETC code. The ANISN results were modified by using the HETC results and the shielding experiment at ISIS, and they were fitted by a simple formula for practical use. High-energy neutron penetrations of slantwise injection and the reflection probabilities of iron slab were calculated with the HETC code, and these results were used for the estimation of the thickness for the iron local shielding of Big RIPSs. Induced radioactivity in the air, accelerator components and the building, and the skyshine effect were also estimated. (author)

  7. Optimization of Amylase and Protease Production from Aspergillus awamori in Single Bioreactor Through EVOP Factorial Design Technique

    Directory of Open Access Journals (Sweden)

    Sangeeta Negi

    2006-01-01

    Full Text Available Evolutionary operation (EVOP factorial design technique was explored in order to economically produce amylase and protease at their optimum level in a single bioreactor by modified solid-state fermentation. Maximum yields of amylase and protease were achieved, using wheat bran as a substrate by a highly potent, locally isolated strain of Aspergillus awamori: Nakazawa MTCC 6652. The strain had been induced previously, inferring the ability to produce both enzymes concomitantly in a single bioreactor with their maximum capacity. The highest secretion of amylase and protease were measured to be 9420.6 and 1930 U/g, respectively, at 37 °C. pH and relative humidity were found to be optimum at 4 and 85 %, evaluated through EVOP method.

  8. SatisFactory Final System Evaluation Report

    OpenAIRE

    Sunlight SA

    2018-01-01

    The present document is a deliverable of the SatisFactory project, funded by the European Commission’s Directorate-General for Research and Innovation (DG RTD), under its Horizon 2020 Research and innovation programme (H2020). The main objective of this deliverable is to report on the SatisFactory Final System Evaluation, with regards to the industrial pilots at COMAU and SUNLIGHT. The evaluation of SatisFactory platform is based on the implementation of the business scenarios where each tool...

  9. WQO is Decidable for Factorial Languages

    KAUST Repository

    Atminas, Aistis

    2017-08-08

    A language is factorial if it is closed under taking factors, i.e. contiguous subwords. Every factorial language can be described by an antidictionary, i.e. a minimal set of forbidden factors. We show that the problem of deciding whether a factorial language given by a finite antidictionary is well-quasi-ordered under the factor containment relation can be solved in polynomial time. We also discuss possible ways to extend our solution to permutations and graphs.

  10. The TRIUMF KAON Factory

    International Nuclear Information System (INIS)

    Craddock, M.K.

    1990-11-01

    The TRIUMF KAON Factory is designed to produce beams of kaons, antiprotons, other hadrons and neutrinos 100 times more intense, or cleaner, than are available now, for a broad range of experiments in particle and nuclear physics. This will require a 100 μA beam of 30 GeV protons, to be produced by an interleaved sequence of two fast-cycling synchrotrons and three storage rings, with the existing TRIUMF H - cyclotron as injector. An $11-million preconstruction study has enabled the overall design to be reviewed and prototypes of various accelerator components to be built and evaluated. Environmental, industrial and economic impact studies have also been completed. Payment of one-third of the total cost of $708 million (Canadian) has been approved by the government of British Columbia; a further third is expected from international sources, on the basis of inter-governmental consultations. A decision on the final third is expected from the government of Canada before the end of 1990. (Author) (15 refs., 7 figs.)

  11. Phosphorus fertilization in sugarcane cultivation under different soil managements

    OpenAIRE

    Sousa Junior, Paulo R. de; Brunharo, Caio A. C. G.; Furlani, Carlos E. A.; Prado, Renato de M.; Maldonado Júnior, Walter; Zerbato, Cristiano

    2017-01-01

    ABSTRACT Soil preparation along with its chemical adjustment is the most important step in sugarcane plantation, especially because it provides proper conditions for plant development. The objective of the present research was to evaluate sugarcane response to the application of different phosphorus doses and their location, associated with both minimum soil tillage and conventional soil tillage. The experiment was conducted in a split-split-plot randomized block design, where the main plots ...

  12. Recent progress in neutrino factory and muon collider research within the Muon Collaboration

    Directory of Open Access Journals (Sweden)

    Mohammad M. Alsharo’a

    2003-08-01

    Full Text Available We describe the status of our effort to realize a first neutrino factory and the progress made in understanding the problems associated with the collection and cooling of muons towards that end. We summarize the physics that can be done with neutrino factories as well as with intense cold beams of muons. The physics potential of muon colliders is reviewed, both as Higgs factories and compact high-energy lepton colliders. The status and time scale of our research and development effort is reviewed as well as the latest designs in cooling channels including the promise of ring coolers in achieving longitudinal and transverse cooling simultaneously. We detail the efforts being made to mount an international cooling experiment to demonstrate the ionization cooling of muons.

  13. Recent progress in neutrino factory and muon collider research within the muon collaboration

    International Nuclear Information System (INIS)

    Alsharo'a, Mohammad M.; Ankenbrandt, Charles M.; Atac, Muzaffer; Autin, Bruno R.; Balbekov, Valeri I.; Barger, Vernon D.; Benary, Odette; Bennett, J. Roger J.; Berger, Michael S.; Berg, J. Scott; Berz, Martin; Black, Edgar L.; Blondel, Alain; Bogacz, S. Alex; Bonesini, M.; Bracker, Stephen B.; Bross, Alan D.; Bruno, Luca; Buckley-Geer, Elizabeth J.; Caldwell, Allen C.; Companelli, Mario; Cassel, Kevin W.; Catanesi, M. Gabriela; Chattopadhyay, Swapan; Chou, Weiren; Cline, David B.; Coney, Linda R.; Conrad, Janet M.; Corlett, John N.; Cremaldi, Lucien; Cummings, Mary Anne; Darve, Christine; DeJongh, Fritz; Drozhdin, Alexandr; Drumm, Paul; Elvira, V. Daniel; Errede, Deborah; Fabich, Adrian; Fawley, William M.; Fernow, Richard C.; Ferrario, Massimo; Finley, David A.; Fisch, Nathaniel J.; Fukui, Yasuo; Furman, Miguel A.; Gabriel, Tony A.; Galea, Raphael; Gallardo, Juan C.; Garoby, Roland; Garren, Alper A.; Geer, Stephen H.; Gilardoni, Simone; Van Ginneken, Andreas J.; Ginzburg, Ilya F.; Godang, Romulus; Goodman, Maury; Gosz, Michael R.; Green, Michael A.; Gruber, Peter; Gunion, John F.; Gupta, Ramesh; Haines, John R.; Hanke, Klaus; Hanson, Gail G.; Han, Tao; Haney, Michael; Hartill, Don; Hartline, Robert E.; Haseroth, Helmut D.; Hassanein, Ahmed; Hoffman, Kara; Holtkamp, Norbert; Holzer, E. Barbara; Johnson, Colin; Johnson, Rolland P.; Johnstone, Carol; Jungmann, Klaus; Kahn, Stephen A.; Kaplan, Daniel M.; Keil, Eberhard K.; Kim, Eun-San; Kim, Kwang-Je; King, Bruce J.; Kirk, Harold G.; Kuno, Yoshitaka; Ladran, Tony S.; Lau, Wing W.; Learned, John G.; Lebedev, Valeri; Lebrun, Paul; Lee, Kevin; Lettry, Jacques A.; Lavender, Marco; Li, Derun; Lombardi, Alessandra; Lu, Changguo; Makino, Kyoko; Malkin, Vladimir; Marfatia, D.; McDonald, Kirk T.; Mezzetto, Mauro; Miller, John R.; Mills, Frederick E.; Mocioiu, I.; Mokhov, Nikolai V.; Monroe, Jocelyn; Moretti, Aldred; Mori, Yoshiharu; Neuffer, David V.; Ng, King-Yuen; Norem, James H.

    2003-01-01

    We describe the status of our effort to realize a first neutrino factory and the progress made in understanding the problems associated with the collection and cooling of muons towards that end. We summarize the physics that can be done with neutrino factories as well as with intense cold beams of muons. The physics potential of muon colliders is reviewed, both as Higgs Factories and compact high energy lepton colliders. The status and timescale of our research and development effort is reviewed as well as the latest designs in cooling channels including the promise of ring coolers in achieving longitudinal and transverse cooling simultaneously. We detail the efforts being made to mount an international cooling experiment to demonstrate the ionization cooling of muons

  14. Baby factories taint surrogacy in Nigeria.

    Science.gov (United States)

    Makinde, Olusesan Ayodeji; Makinde, Olufunmbi Olukemi; Olaleye, Olalekan; Brown, Brandon; Odimegwu, Clifford O

    2016-01-01

    The practice of reproductive medicine in Nigeria is facing new challenges with the proliferation of 'baby factories'. Baby factories are buildings, hospitals or orphanages that have been converted into places for young girls and women to give birth to children for sale on the black market, often to infertile couples, or into trafficking rings. This practice illegally provides outcomes (children) similar to surrogacy. While surrogacy has not been well accepted in this environment, the proliferation of baby factories further threatens its acceptance. The involvement of medical and allied health workers in the operation of baby factories raises ethical concerns. The lack of a properly defined legal framework and code of practice for surrogacy makes it difficult to prosecute baby factory owners, especially when they are health workers claiming to be providing services to clients. In this environment, surrogacy and other assisted reproductive techniques urgently require regulation in order to define when ethico-legal lines have been crossed in providing surrogacy or surrogacy-like services. Copyright © 2015 Reproductive Healthcare Ltd. Published by Elsevier Ltd. All rights reserved.

  15. Haiti. Educating factory workers.

    Science.gov (United States)

    Hughes, H

    1990-04-01

    There are approximately 50,000 workers employed in the light assembly industry in Haiti. About 70% are women, the majority of whom are aged between 25 and 34 years, and are either single or in a nonpermanent relationship with the father of their children. Many live and work in appalling conditions, surviving on very low wages to support several children and an extended family. The acquired immunodeficiency syndrome (AIDS) is now a visible problem in many factories. In October 1988, the Center for the Promotion of Women Workers (Centre de Promotion des Femmes Ouvriers/CPFO) launched a pilot AIDS education program for factory women. The Center, based in a large industrial zone near the airport, runs a health clinic and courses in literacy, communications skills, health promotion and family planning. The new AIDS program allowed CPFO staff to gain entry into factories for the 1st time. Other courses were held outside working hours and outside factory premises. Staff contacted manages by telephone to arrange a meeting to discuss AIDS and to ask permission to hold educational "round tables" with workers. Of 18 managers in the factories approached over a 12-month period, only 2 refused entry to CPFO staff. Almost all managers reported they had registered between 2 and 5 deaths from AIDS among their employees over the past couple of years. A total of 85 educational sessions, each lasting about 2 hours, were held within 28 different factories, community or labor organizations reaching 3063 workers (male and female). In each session, the presentation was carried out by 2 CPFO trained monitors and included a slide show, flip charts, and the video "Met ko," originally produced for Haitian immigrants in New York. The most important aspect of the program was the training of 38 volunteer factory-based health promoters. These promoters attended the round table sessions, where they facilitated discussion and distributed condoms and were subsequently available for counseling co

  16. Improvement of biomass production and glucoamylase activity by Candida famata using factorial design.

    Science.gov (United States)

    Mosbah, Habib; Aissa, Imen; Hassad, Nahla; Farh, Dhaker; Bakhrouf, Amina; Achour, Sami

    2016-07-01

    To improve biomass production and glucoamylase activity (GA) by Candida famata, culture conditions were optimized. A 2(3) full factorial design (FFD) with a response surface model was used to evaluate the effects and interactions of pH (X1 ), time of cultivation (X2 ), and starch concentration (X3 ) on the biomass production and enzyme activity. A total of 16 experiments were conducted toward the construction of an empiric model and a first-order equation. It was found that all factors (X1 , X2 , and X3 ) and their interactions were significant at a certain confidence level (P production and GA of C. famata. Under this optimized medium, the experimental biomass production and GA obtained were 1.8 ± 0.54 g/L and 0.078 ± 0.012 µmol/L/Min, about 1.5- and 1.8-fold, respectively, higher than those in basal medium. The (R(2) ) coefficients obtained were 0.997 and 0.990, indicating an adequate degree of reliability in the model. Approximately 99% of validity of the predicted value was achieved. © 2015 International Union of Biochemistry and Molecular Biology, Inc.

  17. Common angle plots as perception-true visualizations of categorical associations.

    Science.gov (United States)

    Hofmann, Heike; Vendettuoli, Marie

    2013-12-01

    Visualizations are great tools of communications-they summarize findings and quickly convey main messages to our audience. As designers of charts we have to make sure that information is shown with a minimum of distortion. We have to also consider illusions and other perceptual limitations of our audience. In this paper we discuss the effect and strength of the line width illusion, a Muller-Lyer type illusion, on designs related to displaying associations between categorical variables. Parallel sets and hammock plots are both affected by line width illusions. We introduce the common-angle plot as an alternative method for displaying categorical data in a manner that minimizes the effect from perceptual illusions. Results from user studies both highlight the need for addressing line-width illusions in displays and provide evidence that common angle charts successfully resolve this issue.

  18. Internet Factories

    NARCIS (Netherlands)

    Strijkers, R.J.

    2014-01-01

    This thesis contributes a novel concept for introducing new network technologies in network infrastructures. The concept, called Internet factories, describes the methodical process to create and manage application-specific networks from application programs, referred to as Netapps. An Internet

  19. Internet factories

    NARCIS (Netherlands)

    Strijkers, R.J.

    2014-01-01

    This thesis contributes a novel concept for introducing new network technologies in network infrastructures. The concept, called Internet factories, describes the methodical process to create and manage application-specific networks from application programs, referred to as Netapps. An Internet

  20. Baby Factory

    African Journals Online (AJOL)

    Prof

    2018-01-24

    Jan 24, 2018 ... mass media have the power to easily propagate ideas on social change ... issue of 'baby factory' is becoming everyday news affecting the right of ... according to recent mass media reports, teenage girls and young women are.

  1. Modeling habitat split: landscape and life history traits determine amphibian extinction thresholds.

    Directory of Open Access Journals (Sweden)

    Carlos Roberto Fonseca

    Full Text Available Habitat split is a major force behind the worldwide decline of amphibian populations, causing community change in richness and species composition. In fragmented landscapes, natural remnants, the terrestrial habitat of the adults, are frequently separated from streams, the aquatic habitat of the larvae. An important question is how this landscape configuration affects population levels and if it can drive species to extinction locally. Here, we put forward the first theoretical model on habitat split which is particularly concerned on how split distance - the distance between the two required habitats - affects population size and persistence in isolated fragments. Our diffusive model shows that habitat split alone is able to generate extinction thresholds. Fragments occurring between the aquatic habitat and a given critical split distance are expected to hold viable populations, while fragments located farther away are expected to be unoccupied. Species with higher reproductive success and higher diffusion rate of post-metamorphic youngs are expected to have farther critical split distances. Furthermore, the model indicates that negative effects of habitat split are poorly compensated by positive effects of fragment size. The habitat split model improves our understanding about spatially structured populations and has relevant implications for landscape design for conservation. It puts on a firm theoretical basis the relation between habitat split and the decline of amphibian populations.

  2. Modeling habitat split: landscape and life history traits determine amphibian extinction thresholds.

    Science.gov (United States)

    Fonseca, Carlos Roberto; Coutinho, Renato M; Azevedo, Franciane; Berbert, Juliana M; Corso, Gilberto; Kraenkel, Roberto A

    2013-01-01

    Habitat split is a major force behind the worldwide decline of amphibian populations, causing community change in richness and species composition. In fragmented landscapes, natural remnants, the terrestrial habitat of the adults, are frequently separated from streams, the aquatic habitat of the larvae. An important question is how this landscape configuration affects population levels and if it can drive species to extinction locally. Here, we put forward the first theoretical model on habitat split which is particularly concerned on how split distance - the distance between the two required habitats - affects population size and persistence in isolated fragments. Our diffusive model shows that habitat split alone is able to generate extinction thresholds. Fragments occurring between the aquatic habitat and a given critical split distance are expected to hold viable populations, while fragments located farther away are expected to be unoccupied. Species with higher reproductive success and higher diffusion rate of post-metamorphic youngs are expected to have farther critical split distances. Furthermore, the model indicates that negative effects of habitat split are poorly compensated by positive effects of fragment size. The habitat split model improves our understanding about spatially structured populations and has relevant implications for landscape design for conservation. It puts on a firm theoretical basis the relation between habitat split and the decline of amphibian populations.

  3. Humic Acid and Water Management to Decrease Ferro (Fe2+ Solution and Increase Productivity of Established New Rice Field

    Directory of Open Access Journals (Sweden)

    Amrizal Saidi

    2012-01-01

    Full Text Available The purpose of this research was to gain a technological breakthrough in controlling Fe toxicity (Fe2+ on Ultisol ina new established rice field by using humic acid from rice straw compost and water management, so that optimalproduction of rice plants could be achieved. The experiment was designed using a 2 × 4 factorials with 3 replicationsin a split plot design. The main plot was water management consists of 2 levels: continuous and intermittentirrigation (2 weeks flooded and 2 weeks field capacity. Small plot was humic acid which was extracted from ricestraw compost by NaOH 0.5 N which consists of 4 levels: 0, 200, 400, and 600 mg kg-1. The results showed thatapplications of humic acid from 0 to 600 mg kg-1 that was followed by 2 weeks of intermittent irrigation decreasedFe2+ concentration. It was approaching levels that were not toxic to plants, with soil Fe2+ between 180-250 mg kg-1.The best treatment was found at the application of 600 mg kg-1 humic acid extracted from rice straw compostcombined with 2 week flooded – 2 weeks field capacity of water management. Those treatment decreased Fe2+concentration from 1,614 to 180 mg kg-1 and increased the dry weight of grain from 5.15 to 16.73 g pot-1 compared tocontinuous flooding and without humic acid application.

  4. Present status of positron factory project

    International Nuclear Information System (INIS)

    Okada, S.; Sunaga, H.; Kaneko, H.; Tachibana, H.; Yotsumoto, K.; Okamoto, J.

    1992-01-01

    The Japan Atomic Energy Research Institute, JAERI, has been promoting design studies for the 'Positron Factory', in which linac-based intense monoenergetic positron beams are planned to be applied to advanced materials characterization and new fields of basic research. A tentative goal of the beam intensity is 10 10 s -1 , which is assumed to be realized with an electron linac of 100 kW class with a beam energy around 100 to 150 MeV. We performed a technical survey on the dedicated linac. It confirmed technical feasibility of manufacturing the state-of-the-art machine. We have been carrying out a design study of the target. A new concept of the target design is proposed, which is expected to supply intense slow positron beams simultaneously for multiple beam channels, on the basis of Monte Carlo simulations. (author)

  5. A user's guide of a plotting program PLTJOINT

    International Nuclear Information System (INIS)

    Sasaki, Makoto; Sato, Wakaei; Nakagawa, Masayuki; Mori, Takamasa

    1988-02-01

    A plotting program PLTJOINT is able to plot various types of input and output data from neutronics calculations with two dimensional coordinates. These data include cross sections, neutron flux or spectrum, reaction rate distribution and auxiliary data. These are read from the input and output files of the JOINT system and the transport code system using double differential form cross section, and from arbitrary BCD input file. General purpose option is also available. Much care is taken in lettering such as types of characters (italic, Greek letters and characters), super and subscript of alphabet and numeral. Users can design their own characters by using a program IGDRASIL. Most of input data can be read in free format. The code has been programed so flexibly that new functions can be easily added to. (author)

  6. Seed yield and some yield components of sesame as affected by ...

    African Journals Online (AJOL)

    In order to study the effect of different irrigation, N and superabsorbent levels on yield and yield components of sesame, a field experiment was conducted in Khosf Region, Birjand, Iran in 2009 as a split-split plot design based on a randomized complete block design. The treatments included irrigation interval at three levels ...

  7. Usage of a statistical method of designing factorial experiments in the mechanical activation of a complex CuPbZn sulphide concentrate

    Directory of Open Access Journals (Sweden)

    BalហPeter

    2003-09-01

    Full Text Available Mechanical activation belongs to innovative procedures which intensify technological processes by creating new surfaces and making a defective structure of solid phase. Mechanical impact on the solid phase is a suitable procedure to ensure the mobility of its structure elements and to accumulate the mechanical energy that is later used in the processes of leaching.The aim of this study was to realize the mechanical activation of a complex CuPbZn sulphide concentrate (Slovak deposit in an attritor by using of statistical methods for the design of factorial experiments and to determine the conditions for preparing the optimum mechanically activated sample of studied concentrate.The following parameters of the attritor were studied as variables:the weight of sample/steel balls (degree of mill filling, the number of revolutions of the milling shaft and the time of mechanical activation. Interpretation of the chosen variables inducing the mechanical activation of the complex CuPbZn concentrate was also carried out by using statistical methods of factorial design experiments. The presented linear model (23 factorial experiment does not support directly the optimum search, therefore this model was extended to the nonlinear model by the utilization of second order ortogonal polynom. This nonlinear model does not describe adequately the process of new surface formation by the mechanical activation of the studied concentrate. It would be necessary to extend the presented nonlinear model to the nonlinear model of the third order or choose another model. In regard to the economy with the aspect of minimal energy input consumption, the sample with the value of 524 kWht-1 and with the maximum value of specific surface area 8.59 m2g-1 (as a response of the factorial experiment was chosen as the optimum mechanically activated sample of the studied concentrate. The optimum mechanically activated sample of the complex CuPbZn sulphide concentrate was prepared

  8. Study on bio-ethanol production from oil palm (Elaies Guineensis) trunks sap using factorial design

    Energy Technology Data Exchange (ETDEWEB)

    Norhazimah, A. H.; Che Ku, M. Faizala [Faculty of Chemical and Natural Resources Engineering, Universiti Malaysia Pahang (Malaysia)], email: amfaizal@ump.edu.my

    2011-07-01

    Oil palm (Elaies Guineensis) trunks (OPT), a waste generated from the re-plantation of oil palm trees for palm oil production, contain useful fermentable sugar for bio-ethanol production, and are a very important biomass material for future energy production. The fermentation usually can be affected along several parameters: temperature, pH, agitation rate, percentage inoculums, time of incubation, nitrogen sources, age of the inoculums and other chemical and physical factors. Since identifying all the effects of a particular factor on the fermentation process is impractical for reasons of time and cost, the approach of this study was based on a two-level five-factor (25) full factorial design (FFD) in order to identify the independent parameters for screening experiment purposes and determine the range of levels of the factor as well as the regions for optimization. The results from this study showed that the most influential principal factors affecting ethanol concentration and productivity were temperature, followed by initial pH and agitation rate.

  9. Recent Advances in Bismuth-Based Nanomaterials for Photoelectrochemical Water Splitting.

    Science.gov (United States)

    Bhat, Swetha S M; Jang, Ho Won

    2017-08-10

    In recent years, bismuth-based nanomaterials have drawn considerable interest as potential candidates for photoelectrochemical (PEC) water splitting owing to their narrow band gaps, nontoxicity, and low costs. The unique electronic structure of bismuth-based materials with a well-dispersed valence band comprising Bi 6s and O 2p orbitals offers a suitable band gap to harvest visible light. This Review presents significant advancements in exploiting bismuth-based nanomaterials for solar water splitting. An overview of the different strategies employed and the new ideas adopted to improve the PEC performance of bismuth-based nanomaterials are discussed. Morphology control, the construction of heterojunctions, doping, and co-catalyst loading are several approaches that are implemented to improve the efficiency of solar water splitting. Key issues are identified and guidelines are suggested to rationalize the design of efficient bismuth-based materials for sunlight-driven water splitting. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  10. Muon front end for the neutrino factory

    Directory of Open Access Journals (Sweden)

    C. T. Rogers

    2013-04-01

    Full Text Available In the neutrino factory, muons are produced by firing high-energy protons onto a target to produce pions. The pions decay to muons and pass through a capture channel known as the muon front end, before acceleration to 12.6 GeV. The muon front end comprises a variable frequency rf system for longitudinal capture and an ionization cooling channel. In this paper we detail recent improvements in the design of the muon front end.

  11. Mars Science Laboratory Launch-Arrival Space Study: A Pork Chop Plot Analysis

    Science.gov (United States)

    Cianciolo, Alicia Dwyer; Powell, Richard; Lockwood, Mary Kae

    2006-01-01

    Launch-Arrival, or "pork chop", plot analysis can provide mission designers with valuable information and insight into a specific launch and arrival space selected for a mission. The study begins with the array of entry states for each pair of selected Earth launch and Mars arrival dates, and nominal entry, descent and landing trajectories are simulated for each pair. Parameters of interest, such as maximum heat rate, are plotted in launch-arrival space. The plots help to quickly identify launch and arrival regions that are not feasible under current constraints or technology and also provide information as to what technologies may need to be developed to reach a desired region. This paper provides a discussion of the development, application, and results of a pork chop plot analysis to the Mars Science Laboratory mission. This technique is easily applicable to other missions at Mars and other destinations.

  12. Silicon nitride tri-layer vertical Y-junction and 3D couplers with arbitrary splitting ratio for photonic integrated circuits.

    Science.gov (United States)

    Shang, Kuanping; Pathak, Shibnath; Liu, Guangyao; Feng, Shaoqi; Li, Siwei; Lai, Weicheng; Yoo, S J B

    2017-05-01

    We designed and demonstrated a tri-layer Si3N4/SiO2 photonic integrated circuit capable of vertical interlayer coupling with arbitrary splitting ratios. Based on this multilayer photonic integrated circuit platform with each layer thicknesses of 150 nm, 50 nm, and 150 nm, we designed and simulated the vertical Y-junctions and 3D couplers with arbitrary power splitting ratios between 1:10 and 10:1 and with negligible(< -50 dB) reflection. Based on the design, we fabricated and demonstrated tri-layer vertical Y-junctions with the splitting ratios of 1:1 and 3:2 with excess optical losses of 0.230 dB. Further, we fabricated and demonstrated the 1 × 3 3D couplers with the splitting ratio of 1:1:4 for symmetric structures and variable splitting ratio for asymmetric structures.

  13. Mixture-mixture design for the fingerprint optimization of chromatographic mobile phases and extraction solutions for Camellia sinensis.

    Science.gov (United States)

    Borges, Cleber N; Bruns, Roy E; Almeida, Aline A; Scarminio, Ieda S

    2007-07-09

    A composite simplex centroid-simplex centroid mixture design is proposed for simultaneously optimizing two mixture systems. The complementary model is formed by multiplying special cubic models for the two systems. The design was applied to the simultaneous optimization of both mobile phase chromatographic mixtures and extraction mixtures for the Camellia sinensis Chinese tea plant. The extraction mixtures investigated contained varying proportions of ethyl acetate, ethanol and dichloromethane while the mobile phase was made up of varying proportions of methanol, acetonitrile and a methanol-acetonitrile-water (MAW) 15%:15%:70% mixture. The experiments were block randomized corresponding to a split-plot error structure to minimize laboratory work and reduce environmental impact. Coefficients of an initial saturated model were obtained using Scheffe-type equations. A cumulative probability graph was used to determine an approximate reduced model. The split-plot error structure was then introduced into the reduced model by applying generalized least square equations with variance components calculated using the restricted maximum likelihood approach. A model was developed to calculate the number of peaks observed with the chromatographic detector at 210 nm. A 20-term model contained essentially all the statistical information of the initial model and had a root mean square calibration error of 1.38. The model was used to predict the number of peaks eluted in chromatograms obtained from extraction solutions that correspond to axial points of the simplex centroid design. The significant model coefficients are interpreted in terms of interacting linear, quadratic and cubic effects of the mobile phase and extraction solution components.

  14. DKIST enclosure modeling and verification during factory assembly and testing

    Science.gov (United States)

    Larrakoetxea, Ibon; McBride, William; Marshall, Heather K.; Murga, Gaizka

    2014-08-01

    The Daniel K. Inouye Solar Telescope (DKIST, formerly the Advanced Technology Solar Telescope, ATST) is unique as, apart from protecting the telescope and its instrumentation from the weather, it holds the entrance aperture stop and is required to position it with millimeter-level accuracy. The compliance of the Enclosure design with the requirements, as of Final Design Review in January 2012, was supported by mathematical models and other analyses which included structural and mechanical analyses (FEA), control models, ventilation analysis (CFD), thermal models, reliability analysis, etc. During the Enclosure Factory Assembly and Testing the compliance with the requirements has been verified using the real hardware and the models created during the design phase have been revisited. The tests performed during shutter mechanism subsystem (crawler test stand) functional and endurance testing (completed summer 2013) and two comprehensive system-level factory acceptance testing campaigns (FAT#1 in December 2013 and FAT#2 in March 2014) included functional and performance tests on all mechanisms, off-normal mode tests, mechanism wobble tests, creation of the Enclosure pointing map, control system tests, and vibration tests. The comparison of the assumptions used during the design phase with the properties measured during the test campaign provides an interesting reference for future projects.

  15. The Split-Brain Phenomenon Revisited: A Single Conscious Agent with Split Perception.

    Science.gov (United States)

    Pinto, Yair; de Haan, Edward H F; Lamme, Victor A F

    2017-11-01

    The split-brain phenomenon is caused by the surgical severing of the corpus callosum, the main route of communication between the cerebral hemispheres. The classical view of this syndrome asserts that conscious unity is abolished. The left hemisphere consciously experiences and functions independently of the right hemisphere. This view is a cornerstone of current consciousness research. In this review, we first discuss the evidence for the classical view. We then propose an alternative, the 'conscious unity, split perception' model. This model asserts that a split brain produces one conscious agent who experiences two parallel, unintegrated streams of information. In addition to changing our view of the split-brain phenomenon, this new model also poses a serious challenge for current dominant theories of consciousness. Copyright © 2017 Elsevier Ltd. All rights reserved.

  16. Phi factories

    International Nuclear Information System (INIS)

    Anon.

    1990-01-01

    Plans for 'phi factories' gathered momentum with a recent workshop at UCLA. These machines, high luminosity electron-positron colliders working near the phi resonance at 1020 MeV, have been proposed at Laboratories in Europe, the US, Japan and the USSR

  17. Triadic split-merge sampler

    Science.gov (United States)

    van Rossum, Anne C.; Lin, Hai Xiang; Dubbeldam, Johan; van der Herik, H. Jaap

    2018-04-01

    In machine vision typical heuristic methods to extract parameterized objects out of raw data points are the Hough transform and RANSAC. Bayesian models carry the promise to optimally extract such parameterized objects given a correct definition of the model and the type of noise at hand. A category of solvers for Bayesian models are Markov chain Monte Carlo methods. Naive implementations of MCMC methods suffer from slow convergence in machine vision due to the complexity of the parameter space. Towards this blocked Gibbs and split-merge samplers have been developed that assign multiple data points to clusters at once. In this paper we introduce a new split-merge sampler, the triadic split-merge sampler, that perform steps between two and three randomly chosen clusters. This has two advantages. First, it reduces the asymmetry between the split and merge steps. Second, it is able to propose a new cluster that is composed out of data points from two different clusters. Both advantages speed up convergence which we demonstrate on a line extraction problem. We show that the triadic split-merge sampler outperforms the conventional split-merge sampler. Although this new MCMC sampler is demonstrated in this machine vision context, its application extend to the very general domain of statistical inference.

  18. Advanced Envelope Research for Factory Built Housing, Phase 3 -- Whole-House Prototyping

    Energy Technology Data Exchange (ETDEWEB)

    Levy, E.; Mullens, M.; Rath, P.

    2014-04-01

    The Advanced Envelope Research effort will provide factory homebuilders with high performance, cost-effective envelope designs that can be effectively integrated into the plant production process while meeting the thermal requirements of the 2012 IECC standards. Given the affordable nature of manufactured homes, impact on first cost is a major consideration in developing new envelope technologies. This work is part of a multi-phase effort. Phase 1 identified seven envelope technologies and provided a preliminary assessment of three methods for building high performance walls. Phase 2 focused on developing viable product designs, manufacturing strategies, addressing code and structural issues, and cost analysis of the three selected options. An industry advisory committee helped narrow the research focus to perfecting a stud wall design with exterior continuous insulation (CI). Phase 3, completed in two stages, continued the design development effort, exploring and evaluating a range or methods for applying CI to factory built homes. The scope also included material selection, manufacturing and cost analysis, and prototyping and testing. During this phase, a home was built with CI, evaluated, and placed in service. The experience of building a mock up wall section with CI and then constructing on line a prototype home resolved important concerns about how to integrate the material into the production process. First steps were taken toward finding least expensive approaches for incorporating CI in standard factory building practices and a preliminary assessment suggested that even at this early stage the technology is attractive when viewed from a life cycle cost perspective.

  19. Polymeric nanoparticles loaded with the 3,5,3'-triiodothyroacetic acid (Triac), a thyroid hormone: factorial design, characterization, and release kinetics.

    Science.gov (United States)

    Dos Santos, Karen C; da Silva, Maria Fatima Gf; Pereira-Filho, Edenir R; Fernandes, Joao B; Polikarpov, Igor; Forim, Moacir R

    2012-01-01

    This present investigation deals with the development and optimization of polymeric nanoparticle systems loaded with 3,5,3'-triiodothyroacetic acid (Triac). A 2(11-6) fractional factorial design and another 2(2) factorial design were used to study the contrasts on particle size distribution, morphology, surface charge, drug content, entrapment efficiency, and in vitro drug release profiles. The independent variables were the concentration of Triac, type and quantity of both polymer and oil, quantity of Span™ 60 and Tween® 80, volume of solvent and water, and velocity of both magnetic stirring and the transfer of the organic phase into the aqueous solution. The results of optimized formulations showed a narrow size distribution with a polydispersity index lower than 0.200. The particle sizes were on average 159.6 nm and 285.6 nm for nanospheres and nanocapsules, respectively. The zeta potential was higher than 20 mV (in module) and the entrapment efficiency was nearly 100%. A high-performance liquid chromatography method was developed, validated, and efficiently applied to Triac quantification in colloidal suspension. The main independent variables were the type and quantity of the polymer and oil. In vitro drug release profile depicted several features to sustain Triac release. Different formulations showed various release rates indicating an interaction between Triac and other formulation compounds such as polymer and/or oil quantity. Two different models were identified (biexponential and monoexponential) that allowed the control of both the release rate and Triac concentration. Thus, the prepared nanoparticles described here may be of clinical importance in delivering Triac for thyroid treatment.

  20. Smart Factory

    DEFF Research Database (Denmark)

    Bilberg, Arne; Radziwon, Agnieszka; Grube Hansen, David

    2017-01-01

    their innovation and competitive advantage by focusing at their competences, strengths and opportunities. The project suggests innovative solutions and business models through collaboration and use of new technologies. In the Smart Factory, SMEs should be able to collaborate on new products, markets and production......, and to target their challenges and ensure sustainable growth and business in these enterprises. Therefore the focus of the Smart Factory project was to support the growth and sustainable development of the small and medium sized manufacturing industry in Denmark. The project focused on SMEs and how to improve......A large part of Danish Industry is based on Small and Medium Sized Enterprises (SMEs), which account for –99% of the companies in Denmark and about two third of the job positions (source: statistikbanken.dk) . That is why, it is so important also to focus research and development at SMEs...

  1. Broadband non-polarizing terahertz beam splitters with variable split ratio

    KAUST Repository

    Wei, Minggui

    2017-08-15

    Seeking effective terahertz functional devices has always aroused extensive attention. Of particular interest is the terahertz beam splitter. Here, we have proposed, designed, manufactured, and tested a broadband non-polarizing terahertz beam splitter with a variable split ratio based on an all-dielectric metasurface. The metasurface was created by patterning a dielectric surface of the N-step phase gradient and etching to a few hundred micrometers. The conversion efficiency as high as 81% under the normal incidence at 0.7 THz was achieved. Meanwhile, such a splitter works well over a broad frequency range. The split ratio of the proposed design can be continuously tuned by simply shifting the metasurface, and the angle of emergences can also be easily adjusted by choosing the step of phase gradients. The proposed design is non-polarizing, and its performance is kept under different polarizations.

  2. Broadband non-polarizing terahertz beam splitters with variable split ratio

    Science.gov (United States)

    Wei, Minggui; Xu, Quan; Wang, Qiu; Zhang, Xueqian; Li, Yanfeng; Gu, Jianqiang; Tian, Zhen; Zhang, Xixiang; Han, Jiaguang; Zhang, Weili

    2017-08-01

    Seeking effective terahertz functional devices has always aroused extensive attention. Of particular interest is the terahertz beam splitter. Here, we have proposed, designed, manufactured, and tested a broadband non-polarizing terahertz beam splitter with a variable split ratio based on an all-dielectric metasurface. The metasurface was created by patterning a dielectric surface of the N-step phase gradient and etching to a few hundred micrometers. The conversion efficiency as high as 81% under the normal incidence at 0.7 THz was achieved. Meanwhile, such a splitter works well over a broad frequency range. The split ratio of the proposed design can be continuously tuned by simply shifting the metasurface, and the angle of emergences can also be easily adjusted by choosing the step of phase gradients. The proposed design is non-polarizing, and its performance is kept under different polarizations.

  3. Broadband non-polarizing terahertz beam splitters with variable split ratio

    KAUST Repository

    Wei, Minggui; Xu, Quan; Wang, Qiu; Zhang, Xueqian; Li, Yanfeng; Gu, Jianqiang; Tian, Zhen; Zhang, Xixiang; Han, Jiaguang; Zhang, Weili

    2017-01-01

    Seeking effective terahertz functional devices has always aroused extensive attention. Of particular interest is the terahertz beam splitter. Here, we have proposed, designed, manufactured, and tested a broadband non-polarizing terahertz beam splitter with a variable split ratio based on an all-dielectric metasurface. The metasurface was created by patterning a dielectric surface of the N-step phase gradient and etching to a few hundred micrometers. The conversion efficiency as high as 81% under the normal incidence at 0.7 THz was achieved. Meanwhile, such a splitter works well over a broad frequency range. The split ratio of the proposed design can be continuously tuned by simply shifting the metasurface, and the angle of emergences can also be easily adjusted by choosing the step of phase gradients. The proposed design is non-polarizing, and its performance is kept under different polarizations.

  4. The Use of a Fractional Factorial Design to Determine the Factors That Impact 1,3-Propanediol Production from Glycerol by Halanaerobium hydrogeniformans

    Directory of Open Access Journals (Sweden)

    Shivani Kalia

    2016-08-01

    Full Text Available In recent years, biodiesel, a substitute for fossil fuels, has led to the excessive production of crude glycerol. The resulting crude glycerol can possess a high concentration of salts and an alkaline pH. Moreover, current crude glycerol purification methods are expensive, rendering this former commodity a waste product. However, Halanaerobium hydrogeniformans, a haloalkaliphilic bacterium, possesses the metabolic capability to convert glycerol into 1,3-propanediol, a valuable commodity compound, without the need for salt dilution or adjusting pH when grown on this waste. Experiments were performed with different combinations of 24 medium components to determine their impact on the production of 1,3-propanediol by using a fractional factorial design. Tested medium components were selected based on data from the organism’s genome. Analysis of HPLC data revealed enhanced production of 1,3-propanediol with additional glycerol, pH, vitamin B12, ammonium ions, sodium sulfide, cysteine, iron, and cobalt. However, other selected components; nitrate ions, phosphate ions, sulfate ions, sodium:potassium ratio, chloride, calcium, magnesium, silicon, manganese, zinc, borate, nickel, molybdenum, tungstate, copper and aluminum, did not enhance 1,3-propanediol production. The use of a fractional factorial design enabled the quick and efficient assessment of the impact of 24 different medium components on 1,3-propanediol production from glycerol from a haloalkaliphilic bacterium.

  5. The Use of a Fractional Factorial Design to Determine the Factors That Impact 1,3-Propanediol Production from Glycerol by Halanaerobium hydrogeniformans.

    Science.gov (United States)

    Kalia, Shivani; Trager, Jordan; Sitton, Oliver C; Mormile, Melanie R

    2016-08-20

    In recent years, biodiesel, a substitute for fossil fuels, has led to the excessive production of crude glycerol. The resulting crude glycerol can possess a high concentration of salts and an alkaline pH. Moreover, current crude glycerol purification methods are expensive, rendering this former commodity a waste product. However, Halanaerobium hydrogeniformans, a haloalkaliphilic bacterium, possesses the metabolic capability to convert glycerol into 1,3-propanediol, a valuable commodity compound, without the need for salt dilution or adjusting pH when grown on this waste. Experiments were performed with different combinations of 24 medium components to determine their impact on the production of 1,3-propanediol by using a fractional factorial design. Tested medium components were selected based on data from the organism's genome. Analysis of HPLC data revealed enhanced production of 1,3-propanediol with additional glycerol, pH, vitamin B12, ammonium ions, sodium sulfide, cysteine, iron, and cobalt. However, other selected components; nitrate ions, phosphate ions, sulfate ions, sodium:potassium ratio, chloride, calcium, magnesium, silicon, manganese, zinc, borate, nickel, molybdenum, tungstate, copper and aluminum, did not enhance 1,3-propanediol production. The use of a fractional factorial design enabled the quick and efficient assessment of the impact of 24 different medium components on 1,3-propanediol production from glycerol from a haloalkaliphilic bacterium.

  6. Design-Parameters Setup for Power-Split Dual-Regime IVT

    Science.gov (United States)

    Preda, Ion; Ciolan, Gheorghe; Covaciu, Dinu

    2017-10-01

    To analyze the working possibilities of power-split infinitely variable transmissions (IVTs) it is necessary to follow a systematic approach. The method proposed in this paper consists of generating a block diagram of the transmission and then, based on this diagram, to derive the kinematics and dynamics equations of the transmission. For an actual numerical case, the derived equations are used to find characteristic values of the transmission components (gear and chain drives, planetary units) necessary to calculate the speed ratios, the speeds, torques and powers acting on the shafts and coupling (control) elements, and even to estimate the overall efficiency of the transmission.

  7. Atrial fibrillation detection by heart rate variability in Poincare plot.

    Science.gov (United States)

    Park, Jinho; Lee, Sangwook; Jeon, Moongu

    2009-12-11

    Atrial fibrillation (AFib) is one of the prominent causes of stroke, and its risk increases with age. We need to detect AFib correctly as early as possible to avoid medical disaster because it is likely to proceed into a more serious form in short time. If we can make a portable AFib monitoring system, it will be helpful to many old people because we cannot predict when a patient will have a spasm of AFib. We analyzed heart beat variability from inter-beat intervals obtained by a wavelet-based detector. We made a Poincare plot using the inter-beat intervals. By analyzing the plot, we extracted three feature measures characterizing AFib and non-AFib: the number of clusters, mean stepping increment of inter-beat intervals, and dispersion of the points around a diagonal line in the plot. We divided distribution of the number of clusters into two and calculated mean value of the lower part by k-means clustering method. We classified data whose number of clusters is more than one and less than this mean value as non-AFib data. In the other case, we tried to discriminate AFib from non-AFib using support vector machine with the other feature measures: the mean stepping increment and dispersion of the points in the Poincare plot. We found that Poincare plot from non-AFib data showed some pattern, while the plot from AFib data showed irregularly irregular shape. In case of non-AFib data, the definite pattern in the plot manifested itself with some limited number of clusters or closely packed one cluster. In case of AFib data, the number of clusters in the plot was one or too many. We evaluated the accuracy using leave-one-out cross-validation. Mean sensitivity and mean specificity were 91.4% and 92.9% respectively. Because pulse beats of ventricles are less likely to be influenced by baseline wandering and noise, we used the inter-beat intervals to diagnose AFib. We visually displayed regularity of the inter-beat intervals by way of Poincare plot. We tried to design an

  8. Analysis of scaled-factorial-moment data

    International Nuclear Information System (INIS)

    Seibert, D.

    1990-01-01

    We discuss the two standard constructions used in the search for intermittency, the exclusive and inclusive scaled factorial moments. We propose the use of a new scaled factorial moment that reduces to the exclusive moment in the appropriate limit and is free of undesirable multiplicity correlations that are contained in the inclusive moment. We show that there are some similarities among most of the models that have been proposed to explain factorial-moment data, and that these similarities can be used to increase the efficiency of testing these models. We begin by calculating factorial moments from a simple independent-cluster model that assumes only approximate boost invariance of the cluster rapidity distribution and an approximate relation among the moments of the cluster multiplicity distribution. We find two scaling laws that are essentially model independent. The first scaling law relates the moments to each other with a simple formula, indicating that the different factorial moments are not independent. The second scaling law relates samples with different rapidity densities. We find evidence for much larger clusters in heavy-ion data than in light-ion data, indicating possible spatial intermittency in the heavy-ion events

  9. Optimization and influence of parameter affecting the compressive strength of geopolymer concrete containing recycled concrete aggregate: using full factorial design approach

    Science.gov (United States)

    Krishnan, Thulasirajan; Purushothaman, Revathi

    2017-07-01

    There are several parameters that influence the properties of geopolymer concrete, which contains recycled concrete aggregate as the coarse aggregate. In the present study, the vital parameters affecting the compressive strength of geopolymer concrete containing recycled concrete aggregate are analyzedby varying four parameters with two levels using full factorial design in statistical software Minitab® 17. The objective of the present work is to gain an idea on the optimization, main parameter effects, their interactions and the predicted response of the model generated using factorial design. The parameters such as molarity of sodium hydroxide (8M and 12M), curing time (6hrs and 24 hrs), curing temperature (60°C and 90°C) and percentage of recycled concrete aggregate (0% and 100%) are considered. The results show that the curing time, molarity of sodium hydroxide and curing temperature were the orderly significant parameters and the percentage of Recycled concrete aggregate (RCA) was statistically insignificant in the production of geopolymer concrete. Thus, it may be noticeable that the RCA content had negligible effect on the compressive strength of geopolymer concrete. The expected responses from the generated model showed a satisfactory and rational agreement to the experimental data with the R2 value of 97.70%. Thus, geopolymer concrete comprising recycled concrete aggregate can solve the major social and environmental concerns such as the depletion of the naturally available aggregate sources and disposal of construction and demolition waste into the landfill.

  10. [Effect of comprehensive control and prevention for chronic disease in demonstration plot of Chongqing].

    Science.gov (United States)

    Qi, Li; Ding, Xian-bin; Mao, De-qiang; Feng, Lian-gui; Wang, Yu-lin; Jiao, Yan; Zhang, Chun-hua; Lü, Xiao-yan; Li, Hong; Xia, Yi-yin

    2013-03-01

    To evaluate the effect of comprehensive control and prevention for chronic diseases in demonstration plot of Chongqing. Residents were enrolled through multi-stage stratified random sampling method from 17 districts or counties which had successfully established demonstration plots and 21 districts or counties which had not established demonstration plots (non-demonstration plot for short) yet on May, 2012. Questionnaire was designed to survey awareness of health knowledge, health behaviors and utilization of health supportive tools. The results were analyzed by SPSS 15.0 software. We investigated 15 108 residents, 6156 of which were in demonstration plot and others (8951) were not. The findings revealed the percentage of the people who were aware the national action of health lifestyle in demonstration plot and in non-demonstration plot were 44.4% (2734/6157) and 40.2% (3598/8951), respectively, and the awareness of the hypertension risk of too much sodium were 72.4% (4458/6156) and 67.5% (6042/8951), respectively, and the awareness of the cardinal vascular disease (CVD) risk of obesity and overweight were 77.2% (4753/6157) and 69.6% (6230/8951), respectively. About the residents' health behaviors in demonstration plot and in non-demonstration plot, the utilization rates of salt restriction scoop or pot were 23.5% (1447/6157) and 17.9% (1602/8951), and the utilization rates of oil restriction pot were 16.7% (1028/6157) and 11.8% (1064/8951), respectively. Totally, 33 of the 37 indexes were shown higher in demonstration plot than that in non-demonstration plot (P plot was more effective, and the remarkable improvement of health knowledge and behaviors level had been achieved in demonstration plot.

  11. THE USE OF A FACTORIAL DESIGN TO EVALUATE THE PHYSICAL STABILITY OF TABLETS PREPARED BY DIRECT COMPRESSION .2. SELECTION OF EXCIPIENTS SUITABLE FOR USE UNDER TROPICAL STORAGE-CONDITIONS

    NARCIS (Netherlands)

    BOS, CE; BOLHUIS, GK; LERK, CF; DEBOER, JH; DUINEVELD, CAA; SMILDE, AK; DOORNBOS, DA

    1991-01-01

    A factorial design has been used to study the influence of disintegrant concentration, storage temperature and relative humidity upon storage on the physical stability of tablets prepared by direct compression. Tablets prepared from a binary mixture of a filler-binder and a disintegrant were stored

  12. Progress of the PEP-II B-factory

    International Nuclear Information System (INIS)

    Seeman, J.; Browne, M.; Cai, Y.; Colocho, W.; Decker, F.-J.; Donald, M.; Ecklund, S.; Erickson, R.; Fisher, A.; Fox, J.; Heifets, S.; Iverson, R.; Kozanecki, W.; Krejcik, P.; Kulikov, A.; Novokhatski, A.; Schuh, P.; Schwarz, H.; Stanek, M.; Sullivan, M.; Teytelman, D.; Turner, J.; Wienands, U.; Yan, Y.; Yocky, J.; Biagini, M.; Zisman, M.

    2003-01-01

    PEP-II is an e + e - B-Factory Collider located at SLAC operating at the Upsilon 4S resonance. PEP-II has delivered, over the past five years, an integrated luminosity to the BaBar detector of over 139 fb -1 and has reached a luminosity of 6.58 x 10 36 /cm 2 /s. Steady progress is being made in reaching higher luminosity. The goal over the next several years is to reach a luminosity of at least 2 x 10 34 /cm 2 /s. The accelerator physics issues being addressed in PEP-II to reach this goal include the electron cloud instability, beam-beam effects, parasitic beam-beam effects, high RF beam loading, shorter bunches, lower beta y*, interaction region operation, and coupling control. A view of the PEP-II tunnel is shown in Figure 1. The present parameters of the PEP-II B-Factory are shown in Table 1 compared to the design. The present peak luminosity is 219% of design and the best integrated luminosity per month is 7.4 fb -1 that is 225% of design. The best luminosity per month is shown in Figure 2. The integrated luminosity over a month is shown in Figure 3 and the total integrated luminosity in shown in Figure 4. The progress in luminosity has come from correcting the orbits, adding specific orbit bumps to correct coupling and dispersion issues, lowering the beta y* in the LER, and moving the fractional horizontal tunes in both rings to just above the half integer (<0.52)

  13. KAON factories

    International Nuclear Information System (INIS)

    Craddock, M.K.

    1989-09-01

    Proposals for high intensity proton synchrotrons (typically providing 100 μA (6 x 10 14 p/s)) at 30 GeV have been made in Canada, Europe, Japan, the USA and the USSR. These beams would be roughly 100 times more intense than those available now and would yield equivalent increases in the fluxes of secondary particles (kaons, pions, muons, antiprotons, hyperons and neutrinos) - or cleaner beams for a smaller increase in flux. The ability to investigate rare processes on the precision frontier opens new avenues to fundamental questions in both particle and nuclear physics, complementary to traditional approaches via the energy frontier. The demand for higher currents has led to novel features in many of the accelerator designs: asymmetric magnet cycles, avoidance of transition crossing, separate collector and stretcher rings, three-dimensional beam painting at injection, bucket-to-bucket beam transfer, perpendicular biassing of microwave ferrite in the rf tuners, the use of Siberian Snakes to preserve polarization, and the addition of a pre-septum to make slow extraction >99.8% efficient. Other characteristic features include rapid cycling rates, booster stages, H - injection, low impedance enclosures, powerful feedback systems for control of beam instabilities and beam loading, and local collimation systems for handling beam loss. This paper reviews the general features of kaon factory accelerator design and the status of the various proposals

  14. Study on uranium loss during 'Iron-Gypsum Cake' precipitation from acid leach liquor of Jaduguda ore using factorially designed experiments

    International Nuclear Information System (INIS)

    Das, Amrita; Yadav, Manoj; Chatterjee, Ankur; Singh, A.K.; Hubli, R.C.

    2012-01-01

    Acid leaching process for uranium recovery from ore often generates considerable amounts of impurities into the solution. It is a challenge to separate the non-valuable impurities as manageable and stable waste products for final disposal, without losing the valuable constituents. The main impurities that come with the leach liquor are iron and sulfate. Their removal is essential for meeting the iron requirement in leaching circuit and also for making the effluent suitable for recycle. Factorial design analysis was applied to study of process variables for precipitation of iron and sulphate from leach liquor with composition using CaO as precipitation reagent

  15. Use of fractional factorial design for selection of nutrients for culturing Paecilomyces variotii in eucalyptus hemicellulosic hydrolysate

    Directory of Open Access Journals (Sweden)

    J.B. Almeida e Silva

    1998-09-01

    Full Text Available A eucalyptus hemicellulose fraction was hydrolysed by treating eucalyptus wood chips with sulfuric acid. The hydrolysate was used as the substrate to grow Paecilomyces variotii IOC-3764 cultured for 72 or 96 hours. The influence of the inhibitors, nutrients and fermentation time was verified by a 28-4 and, subsequently, a 25-1 fractional factorial design. The effects of the inhibitors (acetic acid and furfural, nutrients (rice bran, urea, potassium nitrate, ammonium sulfate, magnesium sulfate and sodium phosphate and fermentation time were investigated. The highest yield (10.59 g/L of biomass was obtained when the microorganisms were cultivated for 72 hours in a medium composed of 30 g/L rice bran, 9.4 g/L ammonium sulfate (2 g/L nitrogen and 2 g/L sodium phosphate.

  16. Influence of core design, production technique, and material selection on fracture behavior of yttria-stabilized tetragonal zirconia polycrystal fixed dental prostheses produced using different multilayer techniques: split-file, over-pressing, and manually built-up veneers

    Directory of Open Access Journals (Sweden)

    Mahmood DJH

    2016-02-01

    Full Text Available Deyar Jallal Hadi Mahmood, Ewa H Linderoth, Ann Wennerberg, Per Vult Von Steyern Department of Prosthetic Dentistry, Faculty of Odontology, Malmö University, Malmö, Sweden Aim: To investigate and compare the fracture strength and fracture mode in eleven groups of currently, the most commonly used multilayer three-unit all-ceramic yttria-stabilized tetragonal zirconia polycrystal (Y-TZP fixed dental prostheses (FDPs with respect to the choice of core material, veneering material area, manufacturing technique, design of connectors, and radii of curvature of FDP cores. Materials and methods: A total of 110 three-unit Y-TZP FDP cores with one intermediate pontic were made. The FDP cores in groups 1–7 were made with a split-file design, veneered with manually built-up porcelain, computer-aided design-on veneers, and over-pressed veneers. Groups 8–11 consisted of FDPs with a state-of-the-art design, veneered with manually built-up porcelain. All the FDP cores were subjected to simulated aging and finally loaded to fracture. Results: There was a significant difference (P<0.05 between the core designs, but not between the different types of Y-TZP materials. The split-file designs with VITABLOCS® (1,806±165 N and e.max® ZirPress (1,854±115 N and the state-of-the-art design with VITA VM® 9 (1,849±150 N demonstrated the highest mean fracture values. Conclusion: The shape of a split-file designed all-ceramic reconstruction calls for a different dimension protocol, compared to traditionally shaped ones, as the split-file design leads to sharp approximal indentations acting as fractural impressions, thus decreasing the overall strength. The design of a framework is a crucial factor for the load bearing capacity of an all-ceramic FDP. The state-of-the-art design is preferable since the split-file designed cores call for a cross-sectional connector area at least 42% larger, to have the same load bearing capacity as the state-of-the-art designed

  17. Factorials of real negative and imaginary numbers - A new perspective.

    Science.gov (United States)

    Thukral, Ashwani K

    2014-01-01

    Presently, factorials of real negative numbers and imaginary numbers, except for zero and negative integers are interpolated using the Euler's gamma function. In the present paper, the concept of factorials has been generalised as applicable to real and imaginary numbers, and multifactorials. New functions based on Euler's factorial function have been proposed for the factorials of real negative and imaginary numbers. As per the present concept, the factorials of real negative numbers, are complex numbers. The factorials of real negative integers have their imaginary part equal to zero, thus are real numbers. Similarly, the factorials of imaginary numbers are complex numbers. The moduli of the complex factorials of real negative numbers, and imaginary numbers are equal to their respective real positive number factorials. Fractional factorials and multifactorials have been defined in a new perspective. The proposed concept has also been extended to Euler's gamma function for real negative numbers and imaginary numbers, and beta function.

  18. Policy options for the split incentive: Increasing energy efficiency for low-income renters

    International Nuclear Information System (INIS)

    Bird, Stephen; Hernández, Diana

    2012-01-01

    The split incentive problem concerns the lack of appropriate incentives to implement energy efficiency measures. In particular, low income tenants face a phenomenon of energy poverty in which they allocate significantly more of their household income to energy expenditures than other renters. This problem is substantial, affecting 1.89% of all United States' energy use. If effectively addressed, it would create a range of savings between 4 and 11 billion dollars per year for many of the nation's poorest residents. We argue that a carefully designed program of incentives for participants (including landlords) in conjunction with a unique type of utility-managed on-bill financing mechanism has significant potential to solve many of the complications. We focus on three kinds of split incentives, five concerns inherent to addressing split incentive problems (scale, endurance, incentives, savings, political disfavor), and provide a detailed policy proposal designed to surpass those problems, with a particular focus on low-income tenants in a U.S. context. - Highlights: ► We demonstrate the significant impact of the split incentive on low-income tenants. ► We discuss split incentive characteristics, and policy failures. ► We described an on-bill financing model with unique features. ► This policy has protections and incentives for tenants and landlords.

  19. Statistical analysis of weld bead geometry in Ti6Al4V laser cladding. Comparison of central composite design and five step full factorial test plan

    Energy Technology Data Exchange (ETDEWEB)

    Marko, Angelina [Fraunhofer Institute for Production Systems and Design Technology IPK, Berlin (Germany); Graf, Benjamin; Rethmeier, Michael [Fraunhofer Institute for Production Systems and Design Technology IPK, Berlin (Germany). Dept. for Joining and Coating Technology

    2017-11-01

    The process of laser cladding has become more important during recent years because of its broad application for cladding, repair or additive manufacturing. In the field of mechanical engineering, one use is the repair of turbine blades. For high quality and reliability of the repaired components, it is necessary to adjust the weld bead geometry to the specific repair task. The bead geometry influences the metallurgical bonding and the degree of dilution as well as the formation of defects like pores or cracks. Therefore, it is important to know the effects of the different parameters on the welding bead. A valuable tool to meet this industrial challenge is the design of experiments (DoE). In this context, the user can choose between a huge number of test plans. Greater profit of information is expected by a larger test range. In order to confirm the acceptance, a five-step full factorial test plan is compared to a central composite design in this paper. Moreover, the limits of the experimental range are indicated and restrictions can be derived. As the results show, the essential effects are detected with a full factorial test plan as well as with a central composite design. Merely the effect strength could not always be specified unambiguously. On this account and in consideration of cost efficiency, the use of central compound design is recommended in industrial applications.

  20. Statistical analysis of weld bead geometry in Ti6Al4V laser cladding. Comparison of central composite design and five step full factorial test plan

    International Nuclear Information System (INIS)

    Marko, Angelina; Graf, Benjamin; Rethmeier, Michael

    2017-01-01

    The process of laser cladding has become more important during recent years because of its broad application for cladding, repair or additive manufacturing. In the field of mechanical engineering, one use is the repair of turbine blades. For high quality and reliability of the repaired components, it is necessary to adjust the weld bead geometry to the specific repair task. The bead geometry influences the metallurgical bonding and the degree of dilution as well as the formation of defects like pores or cracks. Therefore, it is important to know the effects of the different parameters on the welding bead. A valuable tool to meet this industrial challenge is the design of experiments (DoE). In this context, the user can choose between a huge number of test plans. Greater profit of information is expected by a larger test range. In order to confirm the acceptance, a five-step full factorial test plan is compared to a central composite design in this paper. Moreover, the limits of the experimental range are indicated and restrictions can be derived. As the results show, the essential effects are detected with a full factorial test plan as well as with a central composite design. Merely the effect strength could not always be specified unambiguously. On this account and in consideration of cost efficiency, the use of central compound design is recommended in industrial applications.

  1. Plot 5

    DEFF Research Database (Denmark)

    Lund, Inger-Lise; Hermansen, Anne-Mette; Ferdinand, Trine

    Danskfaglig vejledning informerer om de tanker, der ligger til grund for Plot 5, og beskriver danskfaget ud fra nyere forskning inden for fagets mange delområder. Kapitelvejledning introducerer bogens tekster, forklarer hensigten med kapitlernes opgaver, giver forslag til undervisningen og brugen...

  2. Plot 4

    DEFF Research Database (Denmark)

    Lund, Inger-Lise; Hermansen, Anne-Mette; Ferdinand, Trine

    Danskfaglig vejledning informerer om de tanker, der ligger til grund for Plot 4, og beskriver danskfaget ud fra nyere forskning inden for fagets mange delområder. Kapitelvejledning introducerer bogens tekster, forklarer hensigten med kapitlernes opgaver, giver forslag til undervisningen og brugen...

  3. The Tau-Charm Factory in the ERA of B-Factories and CESR

    International Nuclear Information System (INIS)

    Beers, L.V.; Perl, M.L.

    1994-10-01

    This paper is a collection of presentations made at a conference on tau-charm factories, held at the Stanford Linear Accelerator Center and Stanford University on August 15-16, 1994. The papers presented summarize the physics which can be learned from such a facility, the advantages it would present over planned B-factories and large centers such as CESR, and the types of decay modes which could be observed. More detailed studies of tau physics are opened up, as well as charmonium and charmed systems. Seperate presentations to the proceedings are indexed individually into the database

  4. DETECTION OF FLUX EMERGENCE, SPLITTING, MERGING, AND CANCELLATION OF NETWORK FIELD. I. SPLITTING AND MERGING

    Energy Technology Data Exchange (ETDEWEB)

    Iida, Y.; Yokoyama, T. [Department of Earth and Planetary Science, University of Tokyo, Hongo, Bunkyo-ku, Tokyo 113-0033 (Japan); Hagenaar, H. J. [Lockheed Martin Advanced Technology Center, Org. ADBS, Building 252, 3251 Hanover Street, Palo Alto, CA 94304 (United States)

    2012-06-20

    Frequencies of magnetic patch processes on the supergranule boundary, namely, flux emergence, splitting, merging, and cancellation, are investigated through automatic detection. We use a set of line-of-sight magnetograms taken by the Solar Optical Telescope (SOT) on board the Hinode satellite. We found 1636 positive patches and 1637 negative patches in the data set, whose time duration is 3.5 hr and field of view is 112'' Multiplication-Sign 112''. The total numbers of magnetic processes are as follows: 493 positive and 482 negative splittings, 536 positive and 535 negative mergings, 86 cancellations, and 3 emergences. The total numbers of emergence and cancellation are significantly smaller than those of splitting and merging. Further, the frequency dependence of the merging and splitting processes on the flux content are investigated. Merging has a weak dependence on the flux content with a power-law index of only 0.28. The timescale for splitting is found to be independent of the parent flux content before splitting, which corresponds to {approx}33 minutes. It is also found that patches split into any flux contents with the same probability. This splitting has a power-law distribution of the flux content with an index of -2 as a time-independent solution. These results support that the frequency distribution of the flux content in the analyzed flux range is rapidly maintained by merging and splitting, namely, surface processes. We suggest a model for frequency distributions of cancellation and emergence based on this idea.

  5. The Low-Energy Neutrino Factory

    International Nuclear Information System (INIS)

    Brass, Alan; Geer, Steve; Ellis, Malcolm; Mena, Olga; Pascoli, Silvia

    2008-01-01

    To date most studies of Neutrino Factories have focused on facilities where the energy of the muon in the storage ring has been in the range of 25-50 GeV. In this paper we present a concept for a Low-Energy (∼ 4 GeV) neutrino factory. For baselines of O(1000 km), the rich oscillation pattern at low neutrino interaction energy (0.5 - ∼3 GeV) provides the unique performance of this facility with regard to its sensitivity to CP violation and the determination of the neutrino mass hierarchy. A unique neutrino detector is needed, however, in order to exploit this oscillation pattern. We will describe the basic accelerator facility, demonstrate the methodology of the analysis and give an estimate on how well the Low-Energy neutrino factory can measure θ 13 , CP violation and the mass hierarchy. We will also describe the detector concept that is used, show a preliminary analysis regarding its performance and indicate what R and D is still needed. Finally we will show how the Low-Energy neutrino factory could be a step towards an energy frontier muon collider.

  6. The Energy Factory; EnergieFabriek

    Energy Technology Data Exchange (ETDEWEB)

    Van den Boomen, M.; Van den Dungen, G.J.; Elias, T.; Jansen, M. [Universiteit van Amsterdam UvA, Amsterdam (Netherlands)

    2009-05-15

    The Energy Factory is a collaboration of 26 Dutch local water boards in which options for energy saving and energy production are examined. According to the authors, the initiative of the Energy Factory will lead to a reframing of the role of the water boards. Moreover, they explain how the PPP concept (People, Planet, Profit) may act as platform for negotiations between actors who are involved in the Energy Factory. In addition, the PPP concept is used to demonstrate that the Energy Factory will lead to larger social involvement, social entrepreneurship and growing profits [Dutch] De Energiefabriek is een samenwerkingsverband van 26 waterschappen in Nederland waarin wordt gezocht naar mogelijkheden om energie te besparen en zelf energie te produceren. Volgens de auteurs van deze notitie leidt het initiatief van de Energiefabriek tot een reframing van de rol van waterschappen. Daarnaast leggen ze uit hoe het PPP-concept (People, Profit, Planet) kan fungeren als platform voor onderhandelingen tussen de actoren die betrokken zijn bij de Energiefabriek. Verder wordt met het PPP-concept aangetoond dat de Energiefabriek leidt tot ruimere maatschappelijke betrokkenheid, maatschappelijk ondernemen en winstvergroting.

  7. Split2 Protein-Ligation Generates Active IL-6-Type Hyper-Cytokines from Inactive Precursors.

    Science.gov (United States)

    Moll, Jens M; Wehmöller, Melanie; Frank, Nils C; Homey, Lisa; Baran, Paul; Garbers, Christoph; Lamertz, Larissa; Axelrod, Jonathan H; Galun, Eithan; Mootz, Henning D; Scheller, Jürgen

    2017-12-15

    Trans-signaling of the major pro- and anti-inflammatory cytokines Interleukin (IL)-6 and IL-11 has the unique feature to virtually activate all cells of the body and is critically involved in chronic inflammation and regeneration. Hyper-IL-6 and Hyper-IL-11 are single chain designer trans-signaling cytokines, in which the cytokine and soluble receptor units are trapped in one complex via a flexible peptide linker. Albeit, Hyper-cytokines are essential tools to study trans-signaling in vitro and in vivo, the superior potency of these designer cytokines are accompanied by undesirable stress responses. To enable tailor-made generation of Hyper-cytokines, we developed inactive split-cytokine-precursors adapted for posttranslational reassembly by split-intein mediated protein trans-splicing (PTS). We identified cutting sites within IL-6 (E 134 /S 135 ) and IL-11 (G 116 /S 117 ) and obtained inactive split-Hyper-IL-6 and split-Hyper-IL-11 cytokine precursors. After fusion with split-inteins, PTS resulted in reconstitution of active Hyper-cytokines, which were efficiently secreted from transfected cells. Our strategy comprises the development of a background-free cytokine signaling system from reversibly inactivated precursor cytokines.

  8. Alternative Muon Cooling Options based on Particle-Matter-Interaction for a Neutrino Factory

    CERN Document Server

    Stratakis, D; Alekou, A; Pasternak, J

    2013-01-01

    An ionization cooling channel is a tightly spaced lattice containing absorbers for reducing the momentum of the muon beam, rf cavities for restoring the momentum and strong solenoids for focusing the beam. Such a lattice is an essential feature of most designs for Neutrino Factories and Muon Colliders. Here, we explore three different approaches for designing ionization cooling channels based on periodic solenoidal focusing. Key parameters such as the engineering constraints arising from the length and separation between the solenoidal coils are systematically examined. In addition, we propose novel approaches for reducing the peak magnetic field inside the rf cavities, for example, by using bucked coils for focusing. Our lattice designs are numerically examined against two independent codes: The ICOOL and G4BL code. The performance of our proposed cooling channels is examined by implementing those to the front-end of a Neutrino Factory.

  9. Splitting: The Development of a Measure.

    Science.gov (United States)

    Gerson, Mary-Joan

    1984-01-01

    Described the development of a scale that measures splitting as a psychological structure. The construct validity of the splitting scale is suggested by the positive relationship between splitting scores and a diagnostic measure of the narcissistic personality disorder, as well as a negative relationship between splitting scores and levels of…

  10. Bad splits in bilateral sagittal split osteotomy: systematic review and meta-analysis of reported risk factors.

    Science.gov (United States)

    Steenen, S A; van Wijk, A J; Becking, A G

    2016-08-01

    An unfavourable and unanticipated pattern of the bilateral sagittal split osteotomy (BSSO) is generally referred to as a 'bad split'. Patient factors predictive of a bad split reported in the literature are controversial. Suggested risk factors are reviewed in this article. A systematic review was undertaken, yielding a total of 30 studies published between 1971 and 2015 reporting the incidence of bad split and patient age, and/or surgical technique employed, and/or the presence of third molars. These included 22 retrospective cohort studies, six prospective cohort studies, one matched-pair analysis, and one case series. Spearman's rank correlation showed a statistically significant but weak correlation between increasing average age and increasing occurrence of bad splits in 18 studies (ρ=0.229; Pbad split among the different splitting techniques. A meta-analysis pooling the effect sizes of seven cohort studies showed no significant difference in the incidence of bad split between cohorts of patients with third molars present and concomitantly removed during surgery, and patients in whom third molars were removed at least 6 months preoperatively (odds ratio 1.16, 95% confidence interval 0.73-1.85, Z=0.64, P=0.52). In summary, there is no robust evidence to date to show that any risk factor influences the incidence of bad split. Copyright © 2016 International Association of Oral and Maxillofacial Surgeons. Published by Elsevier Ltd. All rights reserved.

  11. Design and Development of a Relative Humidity and Room Temperature Measurement System with On Line Data Logging Feature for Monitoring the Fermentation Room of Tea Factory

    Directory of Open Access Journals (Sweden)

    Utpal SARMA

    2011-12-01

    Full Text Available The design and development of a Relative Humidity (RH and Room Temperature (RT monitoring system with on line data logging feature for monitoring fermentation room of a tea factory is presented in this paper. A capacitive RH sensor with on chip signal conditioner is taken as RH sensor and a temperature to digital converter (TDC is used for ambient temperature monitoring. An 8051 core microcontroller is the heart of the whole system which reads the digital equivalent of RH data with the help of a 12-bit Analog to Digital (A/D converter and synchronize TDC to get the ambient temperature. The online data logging is achieved with the help of RS-232C communication. Field performance is also studied by installing it in the fermentation room of a tea factory.

  12. Virtual Factory Testbed

    Data.gov (United States)

    Federal Laboratory Consortium — The Virtual Factory Testbed (VFT) is comprised of three physical facilities linked by a standalone network (VFNet). The three facilities are the Smart and Wireless...

  13. Photon factory activity report, 1993

    International Nuclear Information System (INIS)

    1994-01-01

    This issue is the annual report of the Photon Factory, National Laboratory of High Energy Physics. First the outline of the Photon Factory is presented. Injector linac, light source, beamlines and instrumentation, synchrotron radiation facility at the Tristan accumulation ring, and the Tristan super light facility are described in detail. The facility is open to researchers. The user's reports are collected as well. (J.P.N.)

  14. THE USE OF A FACTORIAL DESIGN TO EVALUATE THE PHYSICAL STABILITY OF TABLETS PREPARED BY DIRECT COMPRESSION .1. A NEW APPROACH BASED ON THE RELATIVE CHANGE IN TABLET PARAMETERS

    NARCIS (Netherlands)

    Bos, C. E.; BOLHUIS, G. K.; LERK, C. F.; de Boer, J. H.; DUINEVELD, C. A. A.; Smilde, A. K.; Doornbos, D. A.

    1991-01-01

    A factorial design has been used to study the influence of disintegrant concentration and compression force as well as storage temperature and relative humidity on the physical stability during storage of alpha-lactose monohydrate/rice starch tablets prepared by direct compression. The tablet

  15. Representing uncertainty on model analysis plots

    Directory of Open Access Journals (Sweden)

    Trevor I. Smith

    2016-09-01

    Full Text Available Model analysis provides a mechanism for representing student learning as measured by standard multiple-choice surveys. The model plot contains information regarding both how likely students in a particular class are to choose the correct answer and how likely they are to choose an answer consistent with a well-documented conceptual model. Unfortunately, Bao’s original presentation of the model plot did not include a way to represent uncertainty in these measurements. I present details of a method to add error bars to model plots by expanding the work of Sommer and Lindell. I also provide a template for generating model plots with error bars.

  16. Photocatalytic water splitting: Materials design and high-throughput screening of molecular compositions

    Science.gov (United States)

    Khnayzer, Rony S.

    Due to the expected increases on energy demand in the near future, the development of new catalytic molecular compositions and materials capable of directly converting water, with the aid of solar photons, into hydrogen becomes obviated. Hydrogen is a combustible fuel and precious high-energy feedstock chemical. However, for the water-splitting reaction to proceed efficiently and economically enough for large-scale application, efficient light-absorbing sensitizers and water splitting catalysts are required. To study the kinetics of the water reduction reaction, we have used titania (TiO2) nanoparticles as a robust scaffold to photochemically grow platinum (Pt) nanoparticles from a unique surface-anchored molecular precursor Pt(dcbpy)Cl2 [dcbpy = 4,4'-dicarboxylic acid-2,2'-bipyridine]. The hybrid Pt/TiO 2 nanomaterials obtained were shown to be a superior water reduction catalyst (WRC) in aqueous suspensions when compared with the benchmark platinized TiO2. In addition, cobalt phosphate (CoPi) water oxidation catalyst (WOC) was photochemically assembled on the surface of TiO2, and its structure and mechanism of activity showed resemblance to the established electrochemically grown CoPi material. Both WRC and WOC described above possessed near unity Faradaic efficiency for hydrogen and oxygen production respectively, and were fully characterized by electron microscopy, x-ray absorption spectroscopy, electrochemistry and photochemistry. While there are established materials and molecules that are able to drive water splitting catalysis, some of these efficient semiconductors, including titanium dioxide (TiO2) and tungsten trioxide (WO3), are only able to absorb high-energy (ultraviolet or blue) photons. This high-energy light represents merely a fraction of the solar spectrum that strikes the earth and the energy content of those remaining photons is simply wasted. A strategy to mitigate this problem has been developed over the years in our laboratory. Briefly

  17. Photon Factory Activity Report, 1994

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-12-31

    Photon Factory Activity Report no.12 deals with our activities in the period from October 1993 through September 1994. We operate two light sources at the Photon Factory; the 2.5-GeV Photon Factory storage ring, which is a dedicated light source, and the 6.5-GeV TRISTAN Accumulation Ring, which is parasitically used as a light source. We keep more than seventy experimental stations at two facilities, and accept experiments primarily according to approval by the Program Advisory Committee. The number of proposals to the Photon Factory has been still growing. Three-hundred eighty two proposals were approved by the PAC in FY1994, which is an increase by thirteen percent compared to the previous year. Remarkable was growth in biology proposals, particularly proposals in protein crystallography. In FY 1994, we accepted approximately 20,000 man-days as general users, and almost ten percent of them were from abroad. We always open the facility to users, not only domestic but also international. Recently we have been concentrating our effort to upgrading of the light sources and reconstruction of the experimental stations to keep the Photon Factory an attractive research facility in the forthcoming years. We have already started a program of reducing the emittance of the 2.5-GeV storage ring, which now operates with an emittance of 110 nm-rad, to 27 nm-rad by modifying the lattice, with the goal of operation at the reduced emittance in the fall of 1997. We also have conceived of a conversion of the TRISTAN Accumulation Ring to a dedicated light source of high energies. The on-going TRISTAN project will terminate by the end of 1995, and the TRISTAN Main Ring will be converted to a new B-Factory. At this moment, the TRISTAN Accumulation Ring will be disused as the injector to the Main Ring, and conversion of the AR to a dedicated light source becomes possible. (J.P.N.)

  18. Photon Factory Activity Report, 1994

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-12-31

    Photon Factory Activity Report no.12 deals with our activities in the period from October 1993 through September 1994. We operate two light sources at the Photon Factory; the 2.5-GeV Photon Factory storage ring, which is a dedicated light source, and the 6.5-GeV TRISTAN Accumulation Ring, which is parasitically used as a light source. We keep more than seventy experimental stations at two facilities, and accept experiments primarily according to approval by the Program Advisory Committee. The number of proposals to the Photon Factory has been still growing. Three-hundred eighty two proposals were approved by the PAC in FY1994, which is an increase by thirteen percent compared to the previous year. Remarkable was growth in biology proposals, particularly proposals in protein crystallography. In FY 1994, we accepted approximately 20,000 man-days as general users, and almost ten percent of them were from abroad. We always open the facility to users, not only domestic but also international. Recently we have been concentrating our effort to upgrading of the light sources and reconstruction of the experimental stations to keep the Photon Factory an attractive research facility in the forthcoming years. We have already started a program of reducing the emittance of the 2.5-GeV storage ring, which now operates with an emittance of 110 nm-rad, to 27 nm-rad by modifying the lattice, with the goal of operation at the reduced emittance in the fall of 1997. We also have conceived of a conversion of the TRISTAN Accumulation Ring to a dedicated light source of high energies. The on-going TRISTAN project will terminate by the end of 1995, and the TRISTAN Main Ring will be converted to a new B-Factory. At this moment, the TRISTAN Accumulation Ring will be disused as the injector to the Main Ring, and conversion of the AR to a dedicated light source becomes possible. (J.P.N.)

  19. Photon Factory Activity Report, 1994

    International Nuclear Information System (INIS)

    1995-01-01

    Photon Factory Activity Report no.12 deals with our activities in the period from October 1993 through September 1994. We operate two light sources at the Photon Factory; the 2.5-GeV Photon Factory storage ring, which is a dedicated light source, and the 6.5-GeV TRISTAN Accumulation Ring, which is parasitically used as a light source. We keep more than seventy experimental stations at two facilities, and accept experiments primarily according to approval by the Program Advisory Committee. The number of proposals to the Photon Factory has been still growing. Three-hundred eighty two proposals were approved by the PAC in FY1994, which is an increase by thirteen percent compared to the previous year. Remarkable was growth in biology proposals, particularly proposals in protein crystallography. In FY 1994, we accepted approximately 20,000 man-days as general users, and almost ten percent of them were from abroad. We always open the facility to users, not only domestic but also international. Recently we have been concentrating our effort to upgrading of the light sources and reconstruction of the experimental stations to keep the Photon Factory an attractive research facility in the forthcoming years. We have already started a program of reducing the emittance of the 2.5-GeV storage ring, which now operates with an emittance of 110 nm-rad, to 27 nm-rad by modifying the lattice, with the goal of operation at the reduced emittance in the fall of 1997. We also have conceived of a conversion of the TRISTAN Accumulation Ring to a dedicated light source of high energies. The on-going TRISTAN project will terminate by the end of 1995, and the TRISTAN Main Ring will be converted to a new B-Factory. At this moment, the TRISTAN Accumulation Ring will be disused as the injector to the Main Ring, and conversion of the AR to a dedicated light source becomes possible. (J.P.N.)

  20. Chlorophyll meter reading and total nitrogen content applied as ...

    African Journals Online (AJOL)

    The present study was aimed to assess the relationship between the reading of the chlorophyll meter and the total nitrogen (N) content in the leaf in different parts of the crambe plant, depending on the doses of nitrogen applied to the canopy. Randomized block design in a split plot experimental design was used. The plots ...

  1. Dalitz plot analysis of D0 hadronic decays D0->K0K-pi+, D0->antiK0K+pi- and D0->antiK0K+K-

    International Nuclear Information System (INIS)

    Palano, Antimo

    2002-01-01

    A Dalitz plot analysis of the D 0 hadronic decays D 0 → K 0 K - π + , D 0 → (bar K) 0 K + π - and D 0 → (bar K) 0 K + K - is presented. This analysis is based on a data sample of 22 fb -1 collected with the BABAR detector at the PEP-II asymmetric-energy B Factory at SLAC running on or near the Υ(4S) resonance. The events are selected from continuum e + e - annihilations using the decay D* + → D 0 π + . Preliminary measurements of the branching fractions of the above hadronic decays are obtained. Preliminary estimates of fractions and phases for resonant and nonresonant contributions to the Dalitz plot are also presented

  2. A Randomized Longitudinal Factorial Design to Assess Malaria Vector Control and Disease Management Interventions in Rural Tanzania

    Directory of Open Access Journals (Sweden)

    Randall A. Kramer

    2014-05-01

    Full Text Available The optimization of malaria control strategies is complicated by constraints posed by local health systems, infrastructure, limited resources, and the complex interactions between infection, disease, and treatment. The purpose of this paper is to describe the protocol of a randomized factorial study designed to address this research gap. This project will evaluate two malaria control interventions in Mvomero District, Tanzania: (1 a disease management strategy involving early detection and treatment by community health workers using rapid diagnostic technology; and (2 vector control through community-supported larviciding. Six study villages were assigned to each of four groups (control, early detection and treatment, larviciding, and early detection and treatment plus larviciding. The primary endpoint of interest was change in malaria infection prevalence across the intervention groups measured during annual longitudinal cross-sectional surveys. Recurring entomological surveying, household surveying, and focus group discussions will provide additional valuable insights. At baseline, 962 households across all 24 villages participated in a household survey; 2,884 members from 720 of these households participated in subsequent malariometric surveying. The study design will allow us to estimate the effect sizes of different intervention mixtures. Careful documentation of our study protocol may also serve other researchers designing field-based intervention trials.

  3. A randomized longitudinal factorial design to assess malaria vector control and disease management interventions in rural Tanzania.

    Science.gov (United States)

    Kramer, Randall A; Mboera, Leonard E G; Senkoro, Kesheni; Lesser, Adriane; Shayo, Elizabeth H; Paul, Christopher J; Miranda, Marie Lynn

    2014-05-16

    The optimization of malaria control strategies is complicated by constraints posed by local health systems, infrastructure, limited resources, and the complex interactions between infection, disease, and treatment. The purpose of this paper is to describe the protocol of a randomized factorial study designed to address this research gap. This project will evaluate two malaria control interventions in Mvomero District, Tanzania: (1) a disease management strategy involving early detection and treatment by community health workers using rapid diagnostic technology; and (2) vector control through community-supported larviciding. Six study villages were assigned to each of four groups (control, early detection and treatment, larviciding, and early detection and treatment plus larviciding). The primary endpoint of interest was change in malaria infection prevalence across the intervention groups measured during annual longitudinal cross-sectional surveys. Recurring entomological surveying, household surveying, and focus group discussions will provide additional valuable insights. At baseline, 962 households across all 24 villages participated in a household survey; 2,884 members from 720 of these households participated in subsequent malariometric surveying. The study design will allow us to estimate the effect sizes of different intervention mixtures. Careful documentation of our study protocol may also serve other researchers designing field-based intervention trials.

  4. STANFORD (SLAC): B factory construction begins

    Energy Technology Data Exchange (ETDEWEB)

    Anon.

    1994-03-15

    At a ceremony marking the start of construction, members of the US Congress and Secretary of Energy Hazel O'Leary hailed the new Asymmetric B Factory as the key to continued vitality of the Stanford Linear Accelerator Center (SLAC). Being built in collaboration with the Lawrence Berkeley Laboratory and the Lawrence Livermore National Laboratory, the B factory is a $177 million upgrade of the existing PEP electron-positron collider. Scheduled for completion in 1998, the B factory will generate many millions of B mesons, allowing, among other physics, an intensive search for the phenomena of CP violation in the decays of these particles.

  5. Deficits and Solutions in the Development of Modular Factory Systems

    OpenAIRE

    Achim Kampker; Peter Burggräf; Moritz Krunke; Hanno Voet

    2017-01-01

    As a reaction to current challenges in factory planning, many companies think about introducing factory standards to lower planning times and decrease planning costs. If these factory standards are set-up with a high level of modularity, they are defined as modular factory systems. This paper deals with the main current problems in the application of modular factory systems in practice and presents a solution approach with its basic models. The methodology is based on methods from factory pla...

  6. SuperB: A High-Luminosity Asymmetric e+e- Super Flavor Factory

    Energy Technology Data Exchange (ETDEWEB)

    Bona, M.; /et al.

    2007-05-18

    We discuss herein the exciting physics program that can be accomplished with a very large sample of heavy quark and heavy lepton decays produced in the very clean environment of an e{sup +}e{sup -} collider; a program complementary to that of an experiment such as LHCb at a hadronic machine. It then presents the conceptual design of a new type of e{sup +}e{sup -} collider that produces a nearly two-order-of-magnitude increase in luminosity over the current generation of asymmetric B Factories. The key idea is the use of low emittance beams produced in an accelerator lattice derived from the ILC Damping Ring Design, together with a new collision region, again with roots in the ILC final focus design, but with important new concepts developed in this design effort. Remarkably, SuperB produces this very large improvement in luminosity with circulating currents and wallplug power similar to those of the current B Factories. There is clear synergy with ILC R&D; design efforts have already influenced one another, and many aspects of the ILC Damping Rings and Final Focus would be operationally tested at SuperB. Finally, the design of an appropriate detector, based on an upgrade of BABAR as an example, is discussed in some detail. A preliminary cost estimate is presented, as is an example construction timeline.

  7. A large magnetic detector for the neutrino factory

    International Nuclear Information System (INIS)

    Cervera, A.; Dydak, F.; Gomez Cadenas, J.J.

    2000-01-01

    The physics opportunities of the neutrino factory have been the subject of a number of recent studies. It was shown that sensitive measurements of the angle θ 13 , of MSW effects, and of the sign of the atmospheric mass difference Δm 23 2 are possible, and even CP violation in the neutrino mixing matrix may be within reach. The focus of interest is the oscillation ν e →ν μ , which leads in the well-defined neutrino beam of the neutrino factory to 'wrong-sign' muon events. In this paper, we show that a large magnetic detector will be capable of detecting with high efficiency and small backgrounds such wrong-sign muon events. We present a conceptual design of the apparatus and its performance. Various backgrounds are analysed and we demonstrate that they can be sufficiently suppressed by appropriate cuts. We illustrate the performance of the large magnetic detector by its sensitivity to the angle θ 13

  8. Does African catfish ( Clarias gariepinus ) affect rice in integrated ...

    African Journals Online (AJOL)

    An experiment was conducted for 98 days in the Lake Victoria Basin to investigate the interactions of fish and rice growth performance in rice paddies. The experiment was laid out in a split-plot design, with rice cultivar as the main plot and method of rice-fish culture as the sub-plot. Treatments consisted of two levels of ...

  9. Análise factorial confirmatória do TEOSQp Confirmatory factorial analysis of TEOSQp

    Directory of Open Access Journals (Sweden)

    Helder M. Fernandes

    2010-04-01

    Full Text Available O propósito do presente estudo foi avaliar a confiabilidade, a validade factorial e a invariância (por sexo da versão portuguesa do TEOSQ (Fonseca & Biddle, 2001. Integraram a amostra 1010 estudantes com uma média de idade de 15,42 anos. A análise factorial e da invariância foi avaliada através da análise factorial confirmatória. Os resultados corroboram a proposta de uma estrutura de duas subescalas (tarefa e ego. Com base nos índices de modificação e justificação teórica, o TEOSQ p foi reduzido a 12-itens, com melhores índices de adequação para o modelo oblíquo. Os resultados relativos à invariância por sexo não apresentaram apoio empírico total para a assumpção de equivalência multi-grupo, sugerindo que o TEOSQ p não parece avaliar as orientações cognitivas do mesmo modo, para os indivíduos do sexo masculino (modelo ortogonal e feminino (modelo oblíquo. Face aos resultados obtidos, foram discutidas as implicações conceptuais, empíricas, assim como os aspectos de carácter aplicado.The present research assessed the reliability, factorial validity and measurement invariance (by gender of the Portuguese version of TEOSQ -Task and Ego Orientation in Sport Questionnaire (Fonseca & Biddle, 2001. Data were collected from 1010 physical education students with a mean age of 15.42 ( SD=1.91. Factorial and invariance measurements were tested via confirmatory factorial analysis. Results supported internal consistency for the two proposed subscales (task and ego. Based on modification indices and theoretical justification the TEOSQ p was reduced to 12 items with better goodness-of-fit indices for the oblique model. The results of gender invariance did not provide full empirical support to the multi-group equivalence assumption, being suggested that TEOSQ p does not measure in the same way goal orientations for boys (orthogonal model and girls (oblique model. In light of these results, conceptual, empirical and practical

  10. Experimental and Computational Studies on the Design of Dyes for Water-splitting Dye-sensitized Photoelectrochemical Tandem Cells

    Science.gov (United States)

    Mendez-Hernandez, Dalvin D.

    Solar energy is a promising alternative for addressing the world's current and future energy requirements in a sustainable way. Because solar irradiation is intermittent, it is necessary to store this energy in the form of a fuel so it can be used when required. The light-driven splitting of water into oxygen and hydrogen (a useful chemical fuel) is a fascinating theoretical and experimental challenge that is worth pursuing because the advance of the knowledge that it implies and the availability of water and sunlight. Inspired by natural photosynthesis and building on previous work from our laboratory, this dissertation focuses on the development of water-splitting dye-sensitized photoelectrochemical tandem cells (WSDSPETCs). The design, synthesis, and characterization of high-potential porphyrins and metal-free phthalocyanines with phosphonic anchoring groups are reported. Photocurrents measured for WSDSPETCs made with some of these dyes co-adsorbed with molecular or colloidal catalysts on TiO2 electrodes are reported as well. To guide in the design of new molecules we have used computational quantum chemistry extensively. Linear correlations between calculated frontier molecular orbital energies and redox potentials were built and tested at multiple levels of theory (from semi-empirical methods to density functional theory). Strong correlations (with r2 values > 0.99) with very good predictive abilities (rmsd mV) were found when using density functional theory (DFT) combined with a continuum solvent model. DFT was also used to aid in the elucidation of the mechanism of the thermal relaxation observed for the charge-separated state of a molecular triad that mimics the photo-induced proton coupled electron transfer of the tyrosine-histidine redox relay in the reaction center of Photosystem II. It was found that the inclusion of explicit solvent molecules, hydrogen bonded to specific sites within the molecular triad, was essential to explain the observed thermal

  11. Split Malcev algebras

    Indian Academy of Sciences (India)

    project of the Spanish Ministerio de Educación y Ciencia MTM2007-60333. References. [1] Calderón A J, On split Lie algebras with symmetric root systems, Proc. Indian. Acad. Sci (Math. Sci.) 118(2008) 351–356. [2] Calderón A J, On split Lie triple systems, Proc. Indian. Acad. Sci (Math. Sci.) 119(2009). 165–177.

  12. Dalitz Plot Analysis of $B^0_d \\to K+ \\pi^- \\pi^0$ Decays

    Energy Technology Data Exchange (ETDEWEB)

    Yu, Zhitang; /Wisconsin U., Madison

    2006-05-05

    This thesis describes a Dalitz plot analysis of B{sup 0} {yields} K{sup +}{pi}{sup -}{pi}{sup 0} decays. The data sample comprises 213 million {Upsilon}(4S) {yields} B{bar B} decays collected with the BABAR detector at the PEP-II asymmetric-energy B Factory at the Stanford Linear Accelerator Center in California (SLAC). Preliminary results are presented for measurements of the inclusive branching fraction, quasi-two-body fractions and CP-violating charge asymmetries for intermediate states including K*(892){sup +}{pi}{sup -} and {rho}(770){sup -}K{sup +}. Observations of B{sup 0} decays to the K{pi} S-wave intermediate states, K*{sub 0}(1430){sup +}{pi}{sup -} and K*{sub 0}(1430){sup 0}{pi}{sup 0}, are reported. Evidence of the decay B{sup 0} {yields} K*(892){sup 0}{pi}{sup 0} is seen. We set upper limits at 90% confidence level on branching fractions of the nonresonant and other less significant intermediate states.

  13. Accelerator and Technical Sector Seminar: Future neutrino facilities: the neutrino factory

    CERN Multimedia

    2012-01-01

    Thursday 19.January 2012 at 14:15  -  IT Auditorium (bldg. 31 3-004) Future neutrino facilities: the neutrino factory by Gersende Prior / University of Geneva and CERN EN/MEF The neutrino factory is one of the proposed designs for a future intense neutrino beam facility. In its current layout, a high-power proton beam impinges on an Hg jet target producing pions, decaying in turn into muons. In order to reduce the particle beam emittance, the muon transverse momentum is reduced through ionization cooling by a technically demanding set-up made of closely-packed RF cavities alternating with absorbers. In this talk I will present the motivation for building an intense neutrino beam and some of the proposed neutrino facilities' design. I will discuss the challenges inherent to the cooling of muons, possible optimization of the current baseline and the on-going R&D. ________________ ATS Seminars Organisers: H. Burkhardt (BE), S. Sgobba (EN), G. deRijk (TE)

  14. Two-Loop Splitting Amplitudes

    International Nuclear Information System (INIS)

    Bern, Z.

    2004-01-01

    Splitting amplitudes govern the behavior of scattering amplitudes at the momenta of external legs become collinear. In this talk we outline the calculation of two-loop splitting amplitudes via the unitarity sewing method. This method retains the simple factorization properties of light-cone gauge, but avoids the need for prescriptions such as the principal value or Mandelstam-Leibbrandt ones. The encountered loop momentum integrals are then evaluated using integration-by-parts and Lorentz invariance identities. We outline a variety of applications for these splitting amplitudes

  15. Two-loop splitting amplitudes

    International Nuclear Information System (INIS)

    Bern, Z.; Dixon, L.J.; Kosower, D.A.

    2004-01-01

    Splitting amplitudes govern the behavior of scattering amplitudes at the momenta of external legs become collinear. In this talk we outline the calculation of two-loop splitting amplitudes via the unitarity sewing method. This method retains the simple factorization properties of light-cone gauge, but avoids the need for prescriptions such as the principal value or Mandelstam-Leibbrandt ones. The encountered loop momentum integrals are then evaluated using integration-by-parts and Lorentz invariance identities. We outline a variety of applications for these splitting amplitudes

  16. The TRIUMF KAON factory

    International Nuclear Information System (INIS)

    Craddock, M.K.

    1991-05-01

    The TRIUMF KAON Factory is designed to produce beams of kaons, antiprotons, other hadrons and neutrinos 100 times more intense, or cleaner, than are available now, for a broad range of particle and nuclear physics experiments. This will require a 100 μA beam of 30 GeV protons, to be produced by an interleaved sequence of two fast-cycling synchrotrons and three storage rings, with the existing TRIUMF H - cyclotron as injector. An $11-million preconstruction study has enabled the overall design to be reviewed and prototypes of various components to be built and evaluated -fast-cycling dipole and quadrupole magnets, a dual-frequency magnet power supply, ceramic beam pipes with internal RF shields, an RF cavity (using perpendicular bias), an extraction kicker, and RF beam chopper, and production targets. Environmental, industrial and economic impact studies have also been completed and the cost estimates and schedule updated. The total cost of $708 million (Canadian) will be shared equally between Canada, British Columbia (already approved) and international contributors. The federal decision is expected shortly. (Author) 29 refs., 5 figs

  17. Confirmatory factorial analysis of TEOSQp / Análise factorial confirmatória do TEOSQp

    Directory of Open Access Journals (Sweden)

    Helder M. Fernandes

    2010-01-01

    Full Text Available The present research assessed the reliability, factorial validity and measurement invariance (by gender of the Portuguese version of TEOSQ –Task and Ego Orientation in Sport Questionnaire (Fonseca & Biddle, 2001. Data were collected from 1010 physical education students with a mean age of 15.42 ( SD=1.91. Factorial and invariance measurements were tested via confirmatory factorial analysis. Results supported internal consistency for the two proposed subscales (task and ego. Based on modification indices and theoretical justification the TEOSQ p was reduced to 12 items with better goodness-of-fit indices for the oblique model. The results of gender invariance did not provide full empirical support to the multi-group equivalence assumption, being suggested that TEOSQ p does not measure in the same way goal orientations for boys (orthogonal model and girls (oblique model. In light of these results, conceptual, empirical and practical issues were discussed.

  18. Presenting simulation results in a nested loop plot.

    Science.gov (United States)

    Rücker, Gerta; Schwarzer, Guido

    2014-12-12

    Statisticians investigate new methods in simulations to evaluate their properties for future real data applications. Results are often presented in a number of figures, e.g., Trellis plots. We had conducted a simulation study on six statistical methods for estimating the treatment effect in binary outcome meta-analyses, where selection bias (e.g., publication bias) was suspected because of apparent funnel plot asymmetry. We varied five simulation parameters: true treatment effect, extent of selection, event proportion in control group, heterogeneity parameter, and number of studies in meta-analysis. In combination, this yielded a total number of 768 scenarios. To present all results using Trellis plots, 12 figures were needed. Choosing bias as criterion of interest, we present a 'nested loop plot', a diagram type that aims to have all simulation results in one plot. The idea was to bring all scenarios into a lexicographical order and arrange them consecutively on the horizontal axis of a plot, whereas the treatment effect estimate is presented on the vertical axis. The plot illustrates how parameters simultaneously influenced the estimate. It can be combined with a Trellis plot in a so-called hybrid plot. Nested loop plots may also be applied to other criteria such as the variance of estimation. The nested loop plot, similar to a time series graph, summarizes all information about the results of a simulation study with respect to a chosen criterion in one picture and provides a suitable alternative or an addition to Trellis plots.

  19. Photon factory activity report, 1992

    International Nuclear Information System (INIS)

    1993-01-01

    This issue is the annual report of the Photon Factory, National laboratory of High Energy Physics. First, the outline of the Photon Factory is presented. Injector linac, light source, beamlines and instrumentation, the Tristan synchrotron radiation facility at the accumulation ring, and the Tristan super light facility are described in detail. The facility is open to researchers. The user's reports are collected as well. (J.P.N.) (435 refs.)

  20. Splitting of high power, cw proton beams

    Directory of Open Access Journals (Sweden)

    Alberto Facco

    2007-09-01

    Full Text Available A simple method for splitting a high power, continuous wave (cw proton beam in two or more branches with low losses has been developed in the framework of the EURISOL (European Isotope Separation On-Line Radioactive Ion Beam Facility design study. The aim of the system is to deliver up to 4 MW of H^{-} beam to the main radioactive ion beam production target, and up to 100 kW of proton beams to three more targets, simultaneously. A three-step method is used, which includes magnetic neutralization of a fraction of the main H^{-} beam, magnetic splitting of H^{-} and H^{0}, and stripping of H^{0} to H^{+}. The method allows slow raising and individual fine adjustment of the beam intensity in each branch.

  1. Contour plotting programs for printer and Calcomp plotter

    International Nuclear Information System (INIS)

    Moller, P.

    1980-07-01

    Contour plotting programs for plotting contour diagrams on printers or Calcomp plotters are described. The subroutines also exist in versions that are useful for the special application of finding minima and saddlepoints of nuclear potential energy surfaces generated by the subroutine PETR3 of another program package. For the general user, however, the most interesting aspect of the plotting package is probably the possibility of generating printer contour plots. The plotting of printer contour plots is a very fast and convenient way of displaying two-dimensional functions. 3 figures

  2. Plot til lyst

    DEFF Research Database (Denmark)

    Sandvik, Kjetil

    Den velfungerende krimi faciliterer denne dobbelte plotlæsning ved at muliggøre en særlig form for legende og udforskende interaktion mellem læser og plot: Ved at lægge spor ud og holde tolkningsmuligheder og løsningsmuligheder åbne får vi mulighed for at påtage os og udføre opklaringsarbejdet side......, der inviterer os med ind i selve handlingens rum og forløb og giver os forskellige handlingsmuligheder i forhold til disse. I bogen omtales denne særlige form for plot for forlystelsesplot med henvisning til forlystelsesparken og den særlige form for interaktiv fortælleform, som vi finder der: en...

  3. The rainfall plot: its motivation, characteristics and pitfalls.

    Science.gov (United States)

    Domanska, Diana; Vodák, Daniel; Lund-Andersen, Christin; Salvatore, Stefania; Hovig, Eivind; Sandve, Geir Kjetil

    2017-05-18

    A visualization referred to as rainfall plot has recently gained popularity in genome data analysis. The plot is mostly used for illustrating the distribution of somatic cancer mutations along a reference genome, typically aiming to identify mutation hotspots. In general terms, the rainfall plot can be seen as a scatter plot showing the location of events on the x-axis versus the distance between consecutive events on the y-axis. Despite its frequent use, the motivation for applying this particular visualization and the appropriateness of its usage have never been critically addressed in detail. We show that the rainfall plot allows visual detection even for events occurring at high frequency over very short distances. In addition, event clustering at multiple scales may be detected as distinct horizontal bands in rainfall plots. At the same time, due to the limited size of standard figures, rainfall plots might suffer from inability to distinguish overlapping events, especially when multiple datasets are plotted in the same figure. We demonstrate the consequences of plot congestion, which results in obscured visual data interpretations. This work provides the first comprehensive survey of the characteristics and proper usage of rainfall plots. We find that the rainfall plot is able to convey a large amount of information without any need for parameterization or tuning. However, we also demonstrate how plot congestion and the use of a logarithmic y-axis may result in obscured visual data interpretations. To aid the productive utilization of rainfall plots, we demonstrate their characteristics and potential pitfalls using both simulated and real data, and provide a set of practical guidelines for their proper interpretation and usage.

  4. Resolution V fractional factorial Design for Screening of factors affecting weakly basic drugs liposomal systems.

    Science.gov (United States)

    El-Helaly, Sara Nageeb; Habib, Basant A; Abd El-Rahman, Mohamed K

    2018-04-21

    This study aims to investigate factors affecting weakly basic drugs liposomal systems. Resolution V fractional factorial design (2 V 5-1 ) is used as an example of screening designs that would better be used as a wise step before proceeding with detailed factors effects or optimization studies. Five factors probable to affect liposomal systems of weakly basic drugs were investigated using Amisulpride as a model drug. Factors studied were; A: Preparation technique B: Phosphatidyl choline (PhC) amount (mg) C: Cholesterol: PhC molar ratio, D: Hydration volume (ml) and E: Sonication type. Levels investigated were; Ammonium sulphate-pH gradient technique or Transmembrane zinc chelation-pH gradient technique, 200 or 400 mg, 0 or 0.5, 10 or 20 ml and bath or probe sonication for A, B, C, D and E respectively. Responses measured were Particle size (PS) (nm), Zeta potential (ZP) (mV) and Entrapment efficiency percent (EE%). Ion selective electrode was used as a novel method for measuring unentrapped drug concentration and calculating entrapment efficiency without the need for liposomal separation. Factors mainly affecting the studied responses were Cholesterol: PhC ratio and hydration volume for PS, preparation technique for ZP and preparation technique and hydration volume for EE%. The applied 2 V 5-1 design enabled the use of only 16 trial combinations for screening the influence of five factors on weakly basic drugs liposomal systems. This clarifies the value of the use of screening experiments before extensive investigation of certain factors in detailed optimization studies. Copyright © 2017. Published by Elsevier B.V.

  5. Morphophysiology and nutritive value of signalgrass in silvipastoral system with different tree arrangements

    Directory of Open Access Journals (Sweden)

    Joysiene Sanguinete Coelho

    2014-06-01

    Full Text Available The study was carried out with the aim to evaluate the effect of different special arrangements in forage yield, nutritive value and structure of the understory of signalgrass (Brachiaria decumbens in silvipastoral system with different regrowth times. The design was in complete randomized block with tree replicates in a factorial scheme with split-plots 2 × 2 × 5 consisting two spatial arrangements [Double lines 9 × (2 × 2m and simple lines (9 × 2m] in two sampling places (in the middle of the intercropping and under the three canopy in the plot and five regrowth times (35, 42, 49, 56 e 63 days in the split-plot. It was used a silvipastoral system established since June, 2008 in degraded pasture with signalgrass predominance. The pasture was homogenized by grazing at 15 cm from the soil level. Were evaluated the dry matter yield leaf:stem ratio, light interception and leaf area index. In addition were evaluated the nutritive value characteristics dry matter content, neutral and acid detergent fiber, crude protein and lignin. The photosynthetic active radiation was monitored. The use of simple or double lines did not influence the leaf area index, light interception and dry mass yield. The leaf:stem ratio was influenced by the sampling place only in the double line arrangement. The neutral detergent fiber was substantially high in the double line arrangement. Therefore, the use of double lines reduces the photosynthetic active radiation amount incident in the understory, but does not reduce the forage yield in relation to simple line arrangements. These results indicate the use of double lines arrangement may allow the harvest of more threes without reduce the pasture production.

  6. STANFORD (SLAC): B factory construction begins

    International Nuclear Information System (INIS)

    Anon.

    1994-01-01

    At a ceremony marking the start of construction, members of the US Congress and Secretary of Energy Hazel O'Leary hailed the new Asymmetric B Factory as the key to continued vitality of the Stanford Linear Accelerator Center (SLAC). Being built in collaboration with the Lawrence Berkeley Laboratory and the Lawrence Livermore National Laboratory, the B factory is a $177 million upgrade of the existing PEP electron-positron collider. Scheduled for completion in 1998, the B factory will generate many millions of B mesons, allowing, among other physics, an intensive search for the phenomena of CP violation in the decays of these particles

  7. CADASTRAL CLASSIFICATION OF THE LAND PLOTS IN UKRAINE

    Directory of Open Access Journals (Sweden)

    KIRICHEK Yu. O.

    2016-04-01

    Full Text Available Summary. Work concerns development of national system of classification of the land plots. The developed classification will allow to solve correctly a number of the corresponding cadastral, land management, estimated and other tasks. The analysis of classifications of lands, improvements and real estate in general is made. The created offers concerning creation of a new classification of the land plots in Ukraine. Today the Ukrainian real estate market has no single system that separates the system property groups, classes and types. This significantly complicates the work and can not fully be aware of the specific situation of real estate market. This task is designed to solve classification properties, it is used to transition from a diversity of individual properties to a limited number of classes of evaluation objects. The classification is different functional purpose (use facilities assessment, which determines the difference in value.

  8. Engineering the Polyketide Cell Factory

    DEFF Research Database (Denmark)

    Mølgaard, Louise

    sufficient titers. To improve the production of polyketides biological engineering principles have been applied for the development and engineering of microbial polyketide cell factories. The two biological hosts used for heterologous polyketide production were Aspergillus nidulans and Saccharomyces...... phosphopantetheinylase (PPTase). This versatile vector system can easily be used for expression of other polyketides of interest as well as extended to express whole gene clusters. After achieving proof of principle in terms of expression, the polyketide cell factory must be optimized. The optimization can be achieved...... characterization in bioreactors revealed that the yields of 6-MSA on biomass increased albeit not significantly. As a result of this it may be argued that there is still more work to be done in terms of model building in A. nidulans. Utilizing another well-established cell factory S. cerevisiae the capabilities...

  9. Photon Factory activity report, 1991

    International Nuclear Information System (INIS)

    1992-01-01

    The Photon Factory is a national synchrotron radiation research facility affiliated with the National Laboratory for High Energy Physics located in Tsukuba Science City. The Photon Factory consists of a 2.5 GeV electron/positron linear accelerator, a 2.5 GeV electron/positron storage ring, beam lines and experimental stations. All the facilities for synchrotron radiation research are open to scientists. A part of the accumulation ring of the TRISTAN main ring has been used as a synchrotron radiation source in the energy range from 5.8 to 6.5 GeV. The Photon Factory is composed of three divisions of Injector Linac, Light Source and Instrumentation. The researches of each divisions are reviewed, and the users' short reports are collected. The list of published papers with author index is also included in the publication. (K.I.) 233 refs

  10. A Method for Solving the Voltage and Torque Equations of the Split-Phase Induction Machines

    Directory of Open Access Journals (Sweden)

    G. A. Olarinoye

    2013-06-01

    Full Text Available Single phase induction machines have been the subject of many researches in recent times. The voltage and torque equations which describe the dynamic characteristics of these machines have been quoted in many papers, including the papers that present the simulation results of these model equations. The way and manner in which these equations are solved is not common in literature. This paper presents a detailed procedure of how these equations are to be solved with respect to the splitphase induction machine which is one of the different types of the single phase induction machines available in the market. In addition, these equations have been used to simulate the start-up response of the split phase induction motor on no-load. The free acceleration characteristics of the motor voltages, currents and electromagnetic torque have been plotted and discussed. The simulation results presented include the instantaneous torque-speed characteristics of the Split phase Induction machine. A block diagram of the method for the solution of the machine equations has also been presented.

  11. Survivor shielding. Part A. Nagasaki factory worker shielding

    International Nuclear Information System (INIS)

    Santoro, Robert T.; Barnes, John M.; Azmy, Yousry Y.; Kerr, George D.; Egbert, Stephen D.; Cullings, Harry M.

    2005-01-01

    Recent investigations based on conventional chromosome aberration data by the RERF suggest that the DS86 doses received by many Nagasaki factory workers may have been overestimated by as much as 40% relative to those for other survivors in Japanese-type houses and other shielding configurations (Kodama et al. 2001). Since the factory workers represent about 25% of the Nagasaki survivors with DS86 doses in excess of 0.5 Gy (50 rad), systematic errors in their dose estimates can have a major impact on the risk coefficients from RERF studies. The factory worker doses may have been overestimated for a number of reasons. The calculation techniques, including the factory building modeling, weapon source spectra and cross-section data used in the DS86 shielding calculations were not detailed enough to replicate actual conditions. The models used did not take into account local shielding provided by machinery, tools, and the internal structure in the buildings. In addition, changes in the disposition of shielding following collapse of the building by the blast wave were not considered. The location of large factory complexes may be uncertain, causing large numbers of factory survivors, correctly located relative to each other, to be uniformly too close to the hypocenter. Any or all of these reasons are sufficient to result in an overestimate of the factory worker doses. During the DS02 studies, factory worker doses have been reassessed by more carefully modeling the factory buildings, incorporating improved radiation transport methods and cross-section data and using the most recent bomb leakage spectra (Chapter 2). Two-dimensional discrete ordinates calculations were carried out initially to estimate the effects of workbenches and tools on worker doses to determine if the inclusion of these components would, in fact, reduce the dose by amounts consistent with the RERF observations (Kodama et al. 2001). (author)

  12. Productive variability, border use and plot size in trials with cherry tomato

    Directory of Open Access Journals (Sweden)

    Daniel Santos

    2018-02-01

    Full Text Available ABSTRACT: Knowing the productive variability within protected environments is crucial for choosing the experimental design to be used in that conditions. Thus, the aim of the present study was to assess the variability of fruit production in protected environment cultivated with cherry tomatoes and to verify the border effect and plot size in reducing this variability. To this, data from an uniformity test carried out in a greenhouse with cherry tomato cv. ‘Lili’ were used. Total fresh mass of fruits per plant was considered being these plants arranged in cropping rows parallel to the lateral openings of the greenhouse and also the same plants arranged in columns perpendicular to these openings. To generate the borders, different scenarios were designed by excluding rows and columns and using different plot sizes. In each scenario, homogeneity of variances among the remaining rows and columns was tested. There is no variability of fruit production among rows or columns in trials with cherry tomatoes carried out in greenhouses and the use of border does not bring benefits in terms of reduction of coefficient of variation or reduction of cases of variance heterogeneity among rows or columns. Plots with a size equal to or greater than two plants make possible to use the completely randomized design in the cherry tomato trials in greenhouses.

  13. Multiple hypothesis clustering in radar plot extraction

    NARCIS (Netherlands)

    Huizing, A.G.; Theil, A.; Dorp, Ph. van; Ligthart, L.P.

    1995-01-01

    False plots and plots with inaccurate range and Doppler estimates may severely degrade the performance of tracking algorithms in radar systems. This paper describes how a multiple hypothesis clustering technique can be applied to mitigate the problems involved in plot extraction. The measures of

  14. Storytelling in Earth sciences: The eight basic plots

    Science.gov (United States)

    Phillips, Jonathan

    2012-11-01

    Reporting results and promoting ideas in science in general, and Earth science in particular, is treated here as storytelling. Just as in literature and drama, storytelling in Earth science is characterized by a small number of basic plots. Though the list is not exhaustive, and acknowledging that multiple or hybrid plots and subplots are possible in a single piece, eight standard plots are identified, and examples provided: cause-and-effect, genesis, emergence, destruction, metamorphosis, convergence, divergence, and oscillation. The plots of Earth science stories are not those of literary traditions, nor those of persuasion or moral philosophy, and deserve separate consideration. Earth science plots do not conform those of storytelling more generally, implying that Earth scientists may have fundamentally different motivations than other storytellers, and that the basic plots of Earth Science derive from the characteristics and behaviors of Earth systems. In some cases preference or affinity to different plots results in fundamentally different interpretations and conclusions of the same evidence. In other situations exploration of additional plots could help resolve scientific controversies. Thus explicit acknowledgement of plots can yield direct scientific benefits. Consideration of plots and storytelling devices may also assist in the interpretation of published work, and can help scientists improve their own storytelling.

  15. Atomic Energy (factories) rules: 1988

    International Nuclear Information System (INIS)

    1988-01-01

    These rules are made by the Central Government under the Factories Act, 1948 and extend to all factories engaged in carrying out the purposes of the Atomic Energy Act, 1962. The rules cover the requirements of inspecting staff, health aspects, personnel safety, personnel welfare, working hours, employment of young persons, special provisions in case of dangerous manufacturing processes or operations, supplemental rules for administrative aspects and special powers of competent authority. (M.G.B.)

  16. Cell Factory Stability and Genetic Circuits for Improved Strain Development

    DEFF Research Database (Denmark)

    Rugbjerg, Peter

    . However, all synthetic gene systems -­ including the target metabolic pathways themselves -­ represent a possible fitness burden to the cell and thus constitute a threat to strain stability. In this thesis, several studies served to develop genetic systems for optimizing cell factory development...... systems can challenge the stability of strain designs. A metabolite-­producing Escherichia coli strain was long-­term cultured to study production stability and the dynamic effects of mutations within the cell population. A genetic error landscape of pathway disruptions was identified including particular......Development of new chemical-­‐producing microbial cell factories is an iterative trial-­and-­error process, and to screen candidate cells at high throughput, genetic biosensor systems are appealing. Each biosensor has distinct biological parameters, making modular tuning networks attractive...

  17. Energy–exergy analysis and optimisation of a model sugar factory in Turkey

    International Nuclear Information System (INIS)

    Taner, Tolga; Sivrioglu, Mecit

    2015-01-01

    This study is related to the energy and exergy analysis of a model sugar factory in Turkey. In this study, energy efficiency issue in food industries are investigated within a general context to provide energy saving by reducing energy – exergy losses in the sugar production process. The aim of this study is to determine the best energy and exergy efficiency with the mass and energy balances according to design parameters for a sugar factory. Energy savings that can be applied in food industries are examined. Appropriate scenarios are prepared, and optimization results are compared. As a result of thermodynamics calculations made according to the 1st and 2nd Laws of Thermodynamics, energy and exergy efficiencies of a factory were calculated. Factory total energy efficiency and exergy efficiency were found to be 72.2% and 37.4%, respectively, and according to these results, energy quality was found to be 0.64. In conclusion, the current turbine power process energy and exergy efficiencies were 46.4% and 27.7%, respectively, and the optimized turbine power process energy and exergy efficiencies were 48.7% and 31.7%, respectively. This study performs an attitude to the problem of exergy optimization of the turbine power plant. An overall assessment of the energy and exergy efficiency calculations is performed and is focused on how they should be. - Highlights: • The energy and exergy efficiency of a sugar plant depends more on steam than process. • Energy and exergy efficiencies of a factory increase when the turbine power increases, as in a sugar factory. • Statistical analysis demonstrates the precision of data. • Thermoeconomic analysis of the energy and exergy efficiency of the Çumra Sugar Integrated Plant is performed.

  18. Vegetation resurvey is robust to plot location uncertainty

    Science.gov (United States)

    Kopecký, Martin; Macek, Martin

    2017-01-01

    Aim Resurveys of historical vegetation plots are increasingly used for the assessment of decadal changes in plant species diversity and composition. However, historical plots are usually relocated only approximately. This potentially inflates temporal changes and undermines results. Location Temperate deciduous forests in Central Europe. Methods To explore if robust conclusions can be drawn from resurvey studies despite location uncertainty, we compared temporal changes in species richness, frequency, composition and compositional heterogeneity between exactly and approximately relocated plots. We hypothesized that compositional changes should be lower and changes in species richness should be less variable on exactly relocated plots, because pseudo-turnover inflates temporal changes on approximately relocated plots. Results Temporal changes in species richness were not more variable and temporal changes in species composition and compositional heterogeneity were not higher on approximately relocated plots. Moreover, the frequency of individual species changed similarly on both plot types. Main conclusions The resurvey of historical vegetation plots is robust to uncertainty in original plot location and, when done properly, provides reliable evidence of decadal changes in plant communities. This provides important background for other resurvey studies and opens up the possibility for large-scale assessments of plant community change. PMID:28503083

  19. Beam-beam studies for the proposed SLAC/LBL/LLNL B Factory

    International Nuclear Information System (INIS)

    Furman, M.A.

    1991-05-01

    We present a summary of beam-beam dynamics studies that have been carried out to date for the proposed SLAC/LBL/LLNL B Factory. Most of the material presented here is contained in the proposal's Conceptual Design Report, although post-CDR studies are also presented. 15 refs., 6 figs., 2 tabs

  20. Industrial systems biology and its impact on synthetic biology of yeast cell factories.

    Science.gov (United States)

    Fletcher, Eugene; Krivoruchko, Anastasia; Nielsen, Jens

    2016-06-01

    Engineering industrial cell factories to effectively yield a desired product while dealing with industrially relevant stresses is usually the most challenging step in the development of industrial production of chemicals using microbial fermentation processes. Using synthetic biology tools, microbial cell factories such as Saccharomyces cerevisiae can be engineered to express synthetic pathways for the production of fuels, biopharmaceuticals, fragrances, and food flavors. However, directing fluxes through these synthetic pathways towards the desired product can be demanding due to complex regulation or poor gene expression. Systems biology, which applies computational tools and mathematical modeling to understand complex biological networks, can be used to guide synthetic biology design. Here, we present our perspective on how systems biology can impact synthetic biology towards the goal of developing improved yeast cell factories. Biotechnol. Bioeng. 2016;113: 1164-1170. © 2015 Wiley Periodicals, Inc. © 2015 Wiley Periodicals, Inc.