Removal U(VI) from artificial seawater using facilely and covalently grafted polyacrylonitrile fibers with lysine

Energy Technology Data Exchange (ETDEWEB)

Li, Wenting; Liu, Qi; Liu, Jingyuan; Zhang, Hongsen; Li, Rumin; Li, Zhanshuang; Jing, Xiaoyan [Key Laboratory of Superlight Material and Surface Technology, Ministry of Education, Harbin Engineering University, Harbin 150001 (China); Wang, Jun, E-mail: zhqw1888@sohu.com [Key Laboratory of Superlight Material and Surface Technology, Ministry of Education, Harbin Engineering University, Harbin 150001 (China); Institute of Advanced Marine Materials, Harbin Engineering University, 150001 (China)

2017-05-01

Highlights: • Novel lysine modified fibrous adsorbents were prepared using a facile and green method. • PAN-Lys exhibited high adsorption activity and fast adsorption rate. • PAN-Lys significantly remove U(VI) from simulated seawater. - Abstract: Polyacrylonitrile fibers (PANF) covalently modified with lysine (PAN-Lys) was facilely synthesized and carefully characterized. The critical factors affecting U(VI) adsorption from aqueous solution were exploited, such as initial pH, contact time, concentration and temperature. The adsorption process is strongly dependent on solution pH. With excellent adsorption capacity and high affinity toward U(VI), the process for U(VI) is extremely rapid and the equilibrium can be reached within 20 min. The thermodynamics and kinetics were strictly evaluated. In addition, the hypothetical adsorption mechanisms were proposed. Moreover, the adsorption behavior at low concentrations (3–30 μg L{sup −1}) in simulated seawater was also investigated. Therefore, PAN-Lys can be potentially utilized for the efficient removal of U(VI) from seawater.

Chrome tannage using high-intensity ultrasonic field.

Science.gov (United States)

Mäntysalo, E; Marjoniemi, M; Kilpeläinen, M

1997-04-01

The process time in chrome tannage in leather making, using an elastic compression cycle followed by irradiation by high-intensity ultrasound, is quite short lasting only a few minutes, compared with a process time of several hours in modern chrome tannage. After ultrasonic irradiation, samples were basified in 17 h in chrome liquor at a pH of 4.0 and the shrinkage temperature was measured. The determination of the efficiency for the chrome liquor penetrating into the hides can be based on the steepness of the shrinkage temperature-processing time curve. An approximate value of 20 degrees C min(-1) can be evaluated for the initial slope of the curve when elastic compression and high-intensity ultrasonic irradiation is used, and a processing time of 2 min is required in chrome liquor (plus 17 h basification and 24 h storage time) to obtain leather stable to boiling. Usually, hides are kept in chrome liquor for 2 h.

Criticality experiment for No.2 core of DF-VI fast neutron criticality facility

International Nuclear Information System (INIS)

Yang Lijun; Liu Zhenhua; Yan Fengwen; Luo Zhiwen; Chu Chun; Liang Shuhong

2007-01-01

At the completion of the DF-VI fast neutron criticality facility, its core changed, and it was restarted and a series of experiments and measurements were made. According to the data from 29 criticality experiments, the criticality element number and mass were calculated, the control rod reactivity worth were measured by period method and rod compensate method, reactivity worth of safety rod and safety block were measured using reactivity instrument; the reactivity worth of outer elements and radial distribution of elements were measured too. Based on all the measurements mentioned above, safety operation parameters for core 2 in DF-VI fast neutron criticality facility were conformed. (authors)

Lung cancer in Yorkshire chrome platers, 1972-97.

Science.gov (United States)

Sorahan, T; Harrington, J M

2000-06-01

To investigate mortality from lung cancer in chrome platers, a group exposed to chromic acid. The mortality of a cohort of 1087 chrome platers (920 men, 167 women) from 54 plants situated in the West Riding of Yorkshire, United Kingdom, was investigated for the period 1972-97. All subjects were employed as chrome platers for >/=3 months and all were alive on 31 May 1972. Mortality data were also available for a cohort of 1163 comparison workers with no known occupational exposure to chrome compounds (989 men, 174 women). Information on duration of chrome work and smoking habits collected for a cross sectional survey carried out in 1969-72 were available for 916 (84.3%) of the chrome platers; smoking habits were available for 1004 (86.3%) comparison workers. Two analytical approaches were used, indirect standardisation and Poisson regression. Based on serial mortality rates for the general population of England and Wales, significantly increased mortality from lung cancer was observed (obs) in male chrome platers (obs 60, expected (exp) 32.5, standardised mortality ratio (SMR) 185, pchrome, although data on working after 1972 were not available. Confident interpretation is not possible but occupational exposures to hexavalent chromium may well have been involved in the increased mortality from lung cancer found in this cohort of chrome platers.

The rise of Chrome

OpenAIRE

Jonathan Tamary; Dror G. Feitelson

2015-01-01

Since Chrome’s initial release in 2008 it has grown in market share, and now controls roughly half of the desktop browsers market. In contrast with Internet Explorer, the previous dominant browser, this was not achieved by marketing practices such as bundling the browser with a pre-loaded operating system. This raises the question of how Chrome achieved this remarkable feat, while other browsers such as Firefox and Opera were left behind. We show that both the performance of Chrome and its co...

Refinement in black chrome for use as a solar selective coating

Science.gov (United States)

Mcdonald, G. E.

1974-01-01

Black chrome is significant as a solar selective coating because the current extensive use of black chrome in the electroplating industry as a durable decorative finish makes black chrome widely available on a commercial scale and potentially low in cost as a solar selective coating. Black-chrome deposits were modified by underplating with dull nickel or by being plated on rough surfaces. Both of these procedures increased the visible absorptance. There was no change in the infrared reflectance for the dull-nickel - black-chrome combination from that reported for the bright-nickel - black-chrome combination. However, the bright-nickel - black-chrome coating plated on rough surfaces indicated a slight decrease in infrared reflectance. As integrated over the solar spectrum for air mass 2, the reflectance of the dull-nickel - black-chrome coating was 0.077, of the bright-nickel - black-chrome coating plated on a 0.75-micron (30-microinch) surface was 0.070, of the bright-nickel - black-chrome coating plated on a 2.5 micron (100-microinch) surface was 0.064. The corresponding values for the bright-nickel - black-chrome coating on a 0.0125-micron (0.5-microinch) surface, two samples of black nickel, and two samples of Nextrel black paint were 0.132, 0.123, 0.133, and 0.033, respectively.

Don’t let Chrome expose your passwords

CERN Multimedia

Computer Security Team

2013-01-01

Do you still struggle with remembering your password? Is this despite our many attempts to help you: “Train your Brain: Don't put your password on paper!" (article here), “Creativity@CERN” (article here) and “Maths to the rescue!" (article here)? Then you might have considered the “save your password” features in Chrome, Firefox or Internet Explorer… these features remember your Facebook, CERN, Twitter, Amazon and ebay passwords. But be careful: it might be easy for someone to read them!   If enabled, Chrome, Firefox, Internet Explorer and others can remember the password of specific sites after you’ve logged in to those sites the first time. As the passwords are, however, stored in plain text, they can still be read out by anyone with access to that computer. In Chrome, just type “chrome://settings/passwords” and click the password you want to reveal. Or in F...

Investigation of the interaction of chrome compounds with blue-green microalgae Spirulina platensis

International Nuclear Information System (INIS)

Mosulishvili, L.M.; Belokobyl'skij, A.I.; Kirkesali, E.I.; Frontas'eva, M.V.; Pavlov, S.S.; Aksenova, N.G.

2002-01-01

The interaction of CrIII with the cells of blue-green microalgae Spirulina platensis in course of cultivation in a nutrient medium loaded with corresponding chrome compounds is studied. It is shown that the rate of absorption of CrVI ions by spirulina biomass from the nutrient medium is approximately two orders of magnitude lower as compared to that of CrIII ions. At the same time the presence of CrVI in a nutrient medium is accompanied by a significant decrease in the cell growth rate and by deteriorating the quality of spirulina biomass. It is established that at endogenous insertion of CrIII into the biocomplex of spirulina no change in the valence state of chromium in the nutrient medium is observed and the natural properties of the biomass do not change. On the basis of the obtained concentration dependences, the recommended doses of CrIII in the preparation 'Cr-Spirulina' within the ranges of 30-100 μg/g as a food addition, and 200-250 μg/g for a medical preventive treatment are determined. (author)

Novel Chemical Process for Producing Chrome Coated Metal

Directory of Open Access Journals (Sweden)

Christopher Pelar

2018-01-01

Full Text Available This work demonstrates that a version of the Reduction Expansion Synthesis (RES process, Cr-RES, can create a micron scale Cr coating on an iron wire. The process involves three steps. I. A paste consisting of a physical mix of urea, chrome nitrate or chrome oxide, and water is prepared. II. An iron wire is coated by dipping. III. The coated, and dried, wire is heated to ~800 °C for 10 min in a tube furnace under a slow flow of nitrogen gas. The processed wires were then polished and characterized, primarily with scanning electron microscopy (SEM. SEM indicates the chrome layer is uneven, but only on the scale of a fraction of a micron. The evidence of porosity is ambiguous. Elemental mapping using SEM electron microprobe that confirmed the process led to the formation of a chrome metal layer, with no evidence of alloy formation. Additionally, it was found that thickness of the final Cr layer correlated with the thickness of the precursor layer that was applied prior to the heating step. Potentially, this technique could replace electrolytic processing, a process that generates carcinogenic hexavalent chrome, but further study and development is needed.

Novel Chemical Process for Producing Chrome Coated Metal.

Science.gov (United States)

Pelar, Christopher; Greenaway, Karima; Zea, Hugo; Wu, Chun-Hsien; Luhrs, Claudia C; Phillips, Jonathan

2018-01-05

This work demonstrates that a version of the Reduction Expansion Synthesis (RES) process, Cr-RES, can create a micron scale Cr coating on an iron wire. The process involves three steps. I. A paste consisting of a physical mix of urea, chrome nitrate or chrome oxide, and water is prepared. II. An iron wire is coated by dipping. III. The coated, and dried, wire is heated to ~800 °C for 10 min in a tube furnace under a slow flow of nitrogen gas. The processed wires were then polished and characterized, primarily with scanning electron microscopy (SEM). SEM indicates the chrome layer is uneven, but only on the scale of a fraction of a micron. The evidence of porosity is ambiguous. Elemental mapping using SEM electron microprobe that confirmed the process led to the formation of a chrome metal layer, with no evidence of alloy formation. Additionally, it was found that thickness of the final Cr layer correlated with the thickness of the precursor layer that was applied prior to the heating step. Potentially, this technique could replace electrolytic processing, a process that generates carcinogenic hexavalent chrome, but further study and development is needed.

Ultrasound assisted chrome tanning: Towards a clean leather production technology.

Science.gov (United States)

Mengistie, Embialle; Smets, Ilse; Van Gerven, Tom

2016-09-01

Nowadays, there is a growing demand for a cleaner, but still effective alternative for production processes like in the leather industry. Ultrasound (US) assisted processing of leather might be promising in this sense. In the present paper, the use of US in the conventional chrome tanning process has been studied at different pH, temperature, tanning time, chrome dose and US exposure time by exposing the skin before tanning and during tanning operation. Both prior exposure of the skin to US and US during tanning improves the chrome uptake and reduces the shrinkage significantly. Prior exposure of the skin to US increase the chrome uptake by 13.8% or reduces the chrome dose from 8% to 5% (% based on skin weight) and shorten the process time by half while US during tanning increases the chrome uptake by 28.5% or reduces the chrome dose from 8% to 4% (half) and the tanning time to one third compared to the control without US. Concomitantly, the resulting leather quality (measured as skin shrinkage) improved from 5.2% to 3.2% shrinkage in the skin exposed to US prior tanning and to 1.3% in the skin exposed to US during the tanning experiment. This study confirms that US chrome tanning is an effective and eco-friendly tanning process which can produce a better quality leather product in a shorter process time with a lower chromium dose. Copyright © 2016 Elsevier B.V. All rights reserved.

Lung cancer in Yorkshire chrome platers, 1972-97

OpenAIRE

Sorahan, T.; Harrington, J

2000-01-01

OBJECTIVES—To investigate mortality from lung cancer in chrome platers, a group exposed to chromic acid.
METHODS—The mortality of a cohort of 1087 chrome platers (920 men, 167 women) from 54 plants situated in the West Riding of Yorkshire, United Kingdom, was investigated for the period 1972-97. All subjects were employed as chrome platers for ⩾3 months and all were alive on 31 May 1972. Mortality data were also available for a cohort of 1163 comparison workers with no known occupational expo...

Hex Chrome Free Coatings for Electronics Overview

Science.gov (United States)

Kessel, Kurt

2013-01-01

The overall objective of the Hex Chrome Free Coatings for Electronics project is to evaluate and test pretreatment coating systems not containing hexavalent chrome in avionics and electronics housing applications. This objective will be accomplished by testing strong performing coating systems from prior NASA and DoD testing or new coating systems as determined by the stakeholders.

Adsorption isotherm studies of chromium (VI) from aqueous solutions using sol-gel hydrotalcite-like compounds

Energy Technology Data Exchange (ETDEWEB)

Ramos-Ramirez, Esthela, E-mail: ramosre@quijote.ugto.mx [Centro de Investigaciones en Quimica Inorganica de la Universidad de Guanajuato, Noria Alta s/n, Col. Noria Alta, C.P. 36050, Guanajuato, Gto. (Mexico); Gutierrez Ortega, Norma L.; Conteras Soto, Cesar A. [Centro de Investigaciones en Quimica Inorganica de la Universidad de Guanajuato, Noria Alta s/n, Col. Noria Alta, C.P. 36050, Guanajuato, Gto. (Mexico); Instituto Nacional de Investigaciones Nucleares, Carretera Mexico-Toluca s/n, km 36.5, La Marquesa, Coyoacan Mexico, C.P. 52750 (Mexico); Olguin Gutierrez, Maria T. [Instituto Nacional de Investigaciones Nucleares, Carretera Mexico-Toluca s/n, km 36.5, La Marquesa, Coyoacan Mexico, C.P. 52750 (Mexico)

2009-12-30

In under-developed countries, industries such as paint and pigment manufacturing, leather tanning, chrome plating and textile processing, usually discharge effluents containing Cr(VI) and Cr(III) into municipal sanitary sewers. It has been reported that Cr(VI) acts as a powerful epithelial irritant and as a human carcinogen. In the present work, hydrotalcite-like compounds with a Mg/Al ratio = 2 were synthesized by the sol-gel method. The hydrotalcite-like compounds and their corresponding thermally treated products were characterized by powder X-ray diffraction, infrared spectroscopy and N{sub 2} adsorption. The hydrotalcite-like compounds and the heated solids were used as adsorbents for Cr(VI) in aqueous solutions. Adsorption isotherm studies of Cr(VI) from aqueous solution are described. The adsorbent capacity was determined using the Langmuir, Freundlich and Dubinin-Radushkevich adsorption isotherm models. The Cr(VI) adsorption isotherm data fit best to the Langmuir isotherm model. The maximum Cr(VI) uptake by hydrotalcite and the heated solids was determined using the Langmuir equation and was found to range between 26 and 29 mg Cr(VI)/g adsorbent.

Adsorption isotherm studies of chromium (VI) from aqueous solutions using sol-gel hydrotalcite-like compounds

International Nuclear Information System (INIS)

Ramos-Ramirez, Esthela; Gutierrez Ortega, Norma L.; Conteras Soto, Cesar A.; Olguin Gutierrez, Maria T.

2009-01-01

In under-developed countries, industries such as paint and pigment manufacturing, leather tanning, chrome plating and textile processing, usually discharge effluents containing Cr(VI) and Cr(III) into municipal sanitary sewers. It has been reported that Cr(VI) acts as a powerful epithelial irritant and as a human carcinogen. In the present work, hydrotalcite-like compounds with a Mg/Al ratio = 2 were synthesized by the sol-gel method. The hydrotalcite-like compounds and their corresponding thermally treated products were characterized by powder X-ray diffraction, infrared spectroscopy and N 2 adsorption. The hydrotalcite-like compounds and the heated solids were used as adsorbents for Cr(VI) in aqueous solutions. Adsorption isotherm studies of Cr(VI) from aqueous solution are described. The adsorbent capacity was determined using the Langmuir, Freundlich and Dubinin-Radushkevich adsorption isotherm models. The Cr(VI) adsorption isotherm data fit best to the Langmuir isotherm model. The maximum Cr(VI) uptake by hydrotalcite and the heated solids was determined using the Langmuir equation and was found to range between 26 and 29 mg Cr(VI)/g adsorbent.

Adsorption isotherm studies of chromium (VI) from aqueous solutions using sol-gel hydrotalcite-like compounds.

Science.gov (United States)

Ramos-Ramírez, Esthela; Ortega, Norma L Gutiérrez; Soto, Cesar A Contreras; Gutiérrez, Maria T Olguín

2009-12-30

In under-developed countries, industries such as paint and pigment manufacturing, leather tanning, chrome plating and textile processing, usually discharge effluents containing Cr(VI) and Cr(III) into municipal sanitary sewers. It has been reported that Cr(VI) acts as a powerful epithelial irritant and as a human carcinogen. In the present work, hydrotalcite-like compounds with a Mg/Al ratio=2 were synthesized by the sol-gel method. The hydrotalcite-like compounds and their corresponding thermally treated products were characterized by powder X-ray diffraction, infrared spectroscopy and N(2) adsorption. The hydrotalcite-like compounds and the heated solids were used as adsorbents for Cr(VI) in aqueous solutions. Adsorption isotherm studies of Cr(VI) from aqueous solution are described. The adsorbent capacity was determined using the Langmuir, Freundlich and Dubinin-Radushkevich adsorption isotherm models. The Cr(VI) adsorption isotherm data fit best to the Langmuir isotherm model. The maximum Cr(VI) uptake by hydrotalcite and the heated solids was determined using the Langmuir equation and was found to range between 26 and 29 mg Cr(VI)/g adsorbent.

Biorremediación de suelos contaminados con Cr (VI) y lindano

OpenAIRE

Montero Ruiz, Miguel

2018-01-01

[EN] Nowadays mixed pollution affects more than one third of the polluted soils in the world, therefore is needed to study harmless tecniques for the enviroment capable of doing an efficient management of the resources of a contaminated, degraded and depleted soil, and revalue it by its descontamination, soil health recuperation and revegetation. These actions generate vegetal biomass that can be use to make biofuel, reducing the costs. Chrome has two states of valencia, being Cr (VI) the mos...

Facile synthesis of magnetic Fe3O4/graphene composites for enhanced U(VI) sorption

Science.gov (United States)

Zhao, Donglin; Zhu, Hongyu; Wu, Changnian; Feng, Shaojie; Alsaedi, Ahmed; Hayat, Tasawar; Chen, Changlun

2018-06-01

A novel magnetic Fe3O4/graphene composite (FGC) was fabricated by a facile one-step reaction route and shown to be effective for sorbing U(VI) from aqueous solution. The structure, properties and application of the prepared FGC composite were well evaluated. The high saturation magnetization (45.6 emu/g) made FGC easier to be separated from the media within several seconds under an external magnetic. Effects of different ambient conditions (i.e., pH and ionic strength, contact time, temperatures) on sorption behaviors of U(VI) on FGC were carried out by batch experiments. According to the calculation of Langmuir model, the maximum sorption capacity of U(VI) on the FGC at pH 5.5 and 298 K was 176.47 mg/g. The sorption was correlated with the effects of pH, contact time, and temperature. X-ray photoelectron spectroscopy analysis revealed that U(VI) was sorbed on FGC via oxygen-containing functional groups. This work demonstrated that FGC could be recycled and used as an effective recyclable sorbent for sorption of U(VI).

Estimation of chromium (VI) in various body parts of local chicken

International Nuclear Information System (INIS)

Mahmud, T.; Rehman, R.; Anwar, J.; Abbas, A.; Farooq, M.

2011-01-01

Chicken is a common type of meat source in our food. It is fed with the feed containing small pieces of leather having Cr (VI) which persisted in it during chrome tanning process. The core purpose of present study was to determine the concentration of Cr (VI) in different body parts of chicken like leg, arm, head, heart, liver and bone. Estimation of Cr (VI) was done by preparing the sample solutions after ashing and digestion with nitric acid, by atomic absorption spectrophotometer. The results depicted that the meat part of leg had higher mean concentration (1.266 mg/kg) with 0.037 mg/kg standard error while the lowest average concentration was found in arm (0.233 mg/kg) with standard error as 0.019 mg/kg. In case of bones, the maximum mean concentration was found in head (1.433 mg/kg) with standard error as 0.670 mg/kg. The concentration of Cr (VI) was not found similar in meat and bones of chicken by employing Kruskal Wallis Test. (author)

40 CFR 415.340 - Applicability; description of the chrome pigments production subcategory.

Science.gov (United States)

2010-07-01

... chrome pigments production subcategory. 415.340 Section 415.340 Protection of Environment ENVIRONMENTAL... SOURCE CATEGORY Chrome Pigments Production Subcategory § 415.340 Applicability; description of the chrome pigments production subcategory. This subpart applies to discharges to waters of the United States and...

High exhaust chrome complex using chrome tanned tannery, solid wastes and common hydrocarbons as reductants and masking agents to minimize the liquid and solid wastes: tanning and environmental impact studies

International Nuclear Information System (INIS)

Nawaz, H.R.

2005-01-01

Still no alternate of chrome tanning has been found to achieve the best quality and quantity of leather. But the chrome tanning process is associated with the generation of very toxic liquid and solid wastes. Therefore we emphasized to develop an efficient process for the synthesis of high exhaust chrome complex that could minimize the both liquid and solid wastes up to very low limit. In this research, chrome shavings and raw organic compounds have beneficially utilized as a reductant as well as potential masking agents providing a comprehensive close loop. Two chrome tanning materials have been developed using leather shavings with molasses in product A and replacement of molasses by other organic compounds for chrome complex B. These materials have also been employed for the tanning of goatskins parallel to the commercial BCS from the market. The comparative studies revealed that, the quality of leather made from product B is either better or comparable with the conventional tanning material. The chrome contents in leather have been increased with the simultaneous decreased in spent chrome liquor. Hence the exhaustion rate of chrome complex B has been noted up to 95%. While the physical characteristics of resulted leather from product A and B have been found comparable to that of conventional tanned leather. Therefore this methodology would not only reduce liquid and solid wastes but also provide quality leather and economically multi benefits. (author)

Speciation of Cr(VI) in environmental samples in the vicinity of the ferrochrome smelter.

Science.gov (United States)

Sedumedi, Hilda N; Mandiwana, Khakhathi L; Ngobeni, Prince; Panichev, Nikolay

2009-12-30

The impact of ferrochrome smelter on the contamination of its environment with toxic hexavalent chromium, Cr(VI), was assessed by analyzing smelter dusts, soil, grass and tree barks. For the separation of Cr(VI) from Cr(III), solid samples were treated with 0.1M Na(2)CO(3) and filtered through hydrophilic PDVF 0.45 microm filter prior to the determination of Cr(VI) by electrothermal atomic absorption spectrometry (ET-AAS). Ferrochrome smelter dust was found to contain significant levels of Cr(VI), viz. 43.5 microg g(-1) (cyclone dust), 2710 microg g(-1) (fine dust), and 7800 microg g(-1) (slimes dust) which exceeded the maximum acceptable risk concentration (20 microg g(-1)). The concentration of Cr(VI) in environmental samples of grass (3.4+/-0.2), soil (7.7+/-0.2), and tree bark (11.8+/-1.2) collected in the vicinity of the chrome smelter were higher as compared with the same kind of samples collected from uncontaminated area. The results of the investigation show that ferrochrome smelter is a source of environmental pollution with contamination factors of Cr(VI) ranging between 10 and 50.

Speciation of Cr(VI) in environmental samples in the vicinity of the ferrochrome smelter

International Nuclear Information System (INIS)

Sedumedi, Hilda N.; Mandiwana, Khakhathi L.; Ngobeni, Prince; Panichev, Nikolay

2009-01-01

The impact of ferrochrome smelter on the contamination of its environment with toxic hexavalent chromium, Cr(VI), was assessed by analyzing smelter dusts, soil, grass and tree barks. For the separation of Cr(VI) from Cr(III), solid samples were treated with 0.1 M Na 2 CO 3 and filtered through hydrophilic PDVF 0.45 μm filter prior to the determination of Cr(VI) by electrothermal atomic absorption spectrometry (ET-AAS). Ferrochrome smelter dust was found to contain significant levels of Cr(VI), viz. 43.5 μg g -1 (cyclone dust), 2710 μg g -1 (fine dust), and 7800 μg g -1 (slimes dust) which exceeded the maximum acceptable risk concentration (20 μg g -1 ). The concentration of Cr(VI) in environmental samples of grass (3.4 ± 0.2), soil (7.7 ± 0.2), and tree bark (11.8 ± 1.2) collected in the vicinity of the chrome smelter were higher as compared with the same kind of samples collected from uncontaminated area. The results of the investigation show that ferrochrome smelter is a source of environmental pollution with contamination factors of Cr(VI) ranging between 10 and 50.

The coating layer structure of commercial chrome plates

International Nuclear Information System (INIS)

Chen, Sheng

2015-01-01

Highlights: • AES and XPS depth profiling analysis were used in the experiment. • The detailed coating layer structure of the commercial chrome plate was obtained. • Peak fitting method was used to investigate the chemical states of Cr in the coating. - Abstract: The surface and cross-sectional morphologies of the commercial chrome plate coating layer with the thickness of dozens of nanometers have been observed. To investigate the detailed structure of the coating layer, Auger electron spectroscopy (AES) and X-ray photoelectron spectroscopy (XPS) combined with the low energy Ar + sputtering technique have been employed. Through careful analysis of experimental data, it can be obtained that the coating layer of commercial chrome plates is composed of four layers from top to bottom with different compositions

Bio-reduction of Cr(VI) by exopolysaccharides (EPS) from indigenous bacterial species of Sukinda chromite mine, India.

Science.gov (United States)

Harish, R; Samuel, Jastin; Mishra, R; Chandrasekaran, N; Mukherjee, A

2012-07-01

Chrome mining activity has contributed intensively towards pollution of hexavalent chromium around Sukinda Valley, Orissa, India. In an attempt to study the specific contribution of exopolysaccharides (EPS) extracted from indigenous isolates towards Cr(VI) reduction, three chromium (VI) tolerant strains were isolated from the effluent mining sludge. Based on the tolerance towards Cr(VI) and EPS production capacity, one of them was selected for further work. The taxonomic identity of the selected strain was confirmed to be Enterobacter cloacae (showing 98% similarity in BLAST search to E. cloacae) through 16S rRNA analysis. The EPS production was observed to increase with increasing Cr(VI) concentration in the growth medium, highest being 0.078 at 100 mg/l Cr(VI). The extracted EPS from Enterobacter cloacae SUKCr1D was able to reduce 31.7% of Cr(VI) at 10 mg/l concentration, which was relevant to the prevailing natural concentrations at Sukinda mine effluent sludge. The FT-IR spectral studies confirmed the surface chemical interactions of hexavalent chromium with EPS.

Study on creep-fatigue evaluation of chrome-molybdenum steel

International Nuclear Information System (INIS)

Aoto, Kazumi; Wada, Yusaku

1993-01-01

Though chrome-molybdenum steel has quite different basic material properties from austenitic stainless steel, the life fraction rule based on an advanced ductility exhaustion theory proposed for SUS304 is able to give proper prediction for creep-fatigue life of chrome-molybdenum steel. The applicability of the present evaluation method to chrome-molybdenum steel is validated by both mechanical study and micro-structural observation. The mechanism of creep-fatigue failure of Mod.9Cr-1Mo(NT) is one of the most controversial subjects among researchers. However, it is clarified in this report that creep-fatigue damage of this material under actual loading conditions is dominated by creep-cavitation of grain boundaries as same way as that of austenitic stainless steel. Furthermore, for the life reduction of low cycle fatigue of chrome-molybdenum steel with compression-side strain hold, both effects of mean stress and oxide-wedge are denied and it is insisted that the acceleration of fatigue-crack propagation is occurred by oxide-progress location and its thickness. (author)

Improvement of exhaustion and fixation of chrome tan by hydroxy organic acids

International Nuclear Information System (INIS)

Nashy, E.H.A.; Khedr, M.H.; EL-Sayed, N.H.

2005-01-01

Chrome tan is the most important tanning agent in the tanning industry, but it causes extreme pollution due to the incomplete exhaustion of the serious chrome cations in tanning bath. The exhaustion and fixation of chrome tan were improved in this study through treatment of delimed hide with three carboxylic acids named citric, malic and tartaric acids before exposure to tanning process. The process was optimized taking into the account the shaking rate, chrome concentration (%), initial ph, acids concentration, and temperature and contact time. The optimum conditions for exhaustion, fixation, shrinkage temperature as well as skin quality showed that agitation rate of 150 rpm, chrome concentration of 16%, initial ph of 8.5, acid concentration of 3% tartaric acid, temperature of 35 degree C and contact time of 24 hr.The best results obtained are 88% exhaustion, 88.32% fixation and 106 degree C shrinkage temperature in aqueous medium

The influence of Chromium supplied by tanning and wet finishing processes on the formation of cr(vi in leather

Directory of Open Access Journals (Sweden)

W. F. Fuck

2011-06-01

Full Text Available Chromium used in leather manufacturing can be oxidized from the trivalent to the hexavalent state, causing environmental concerns. In this study, the influence of Cr(III from tanning, deacidification pH, fatliquors, chrome retanning and vegetable retanning on the formation of Cr(VI in leather was analyzed by comparing natural and aged samples. In wet-blue leather, even after aging and in fatliquored leathers that did not suffer the aging process, the presence of Cr(VI was always below the detection limit of 3 mg/kg. Considering the presence of Cr(VI, the supply of chromium during the retanning step had a more significant effect than during the tanning. In the fatliquoring process with sulfites, fish and synthetic fatliquor leather samples contained Cr(VI when aged, and the highest concentration detected was 26.7 mg/kg. The evaluation of Cr(VI formation led to recommendations for regulation in the leather industry.

Molecular spectroscopic study for suggested mechanism of chrome tanned leather

Science.gov (United States)

Nashy, Elshahat H. A.; Osman, Osama; Mahmoud, Abdel Aziz; Ibrahim, Medhat

2012-03-01

Collagen represents the structural protein of the extracellular matrix, which gives strength of hides and/or skin under tanning process. Chrome tan is the most important tanning agent all over the world. The methods for production of leather evolved over several centuries as art and engineering with little understanding of the underlying science. The present work is devoted to suggest the most probable mechanistic action of chrome tan on hide proteins. First the affect of Cr upon hide protein is indicated by the studied mechanical properties. Then the spectroscopic characterization of the hide protein as well as chrome tanned leather was carried out with Horizontal Attenuated Total Reflection (HATR) FT-IR. The obtained results indicate how the chromium can attached with the active sites of collagen. Molecular modeling confirms that chromium can react with amino as well as carboxylate groups. Four schemes were obtained to describe the possible interactions of chrome tan with hide proteins.

Chromium VI and stomach cancer: a meta-analysis of the current epidemiological evidence.

Science.gov (United States)

Welling, Roberta; Beaumont, James J; Petersen, Scott J; Alexeeff, George V; Steinmaus, Craig

2015-02-01

Chromium VI (hexavalent chromium, Cr(VI)) is an established cause of lung cancer, but its association with gastrointestinal cancer is less clear. The goal of this study was to examine whether the current human epidemiological research on occupationally inhaled Cr(VI) supports the hypothesis that Cr(VI) is associated with human stomach cancer. Following a thorough literature search and review of individual studies, we used meta-analysis to summarise the current epidemiological literature on inhaled Cr(VI) and stomach cancer, explore major sources of heterogeneity, and assess other elements of causal inference. We identified 56 cohort and case-control studies and 74 individual relative risk (RR) estimates on stomach cancer and Cr(VI) exposure or work in an occupation associated with high Cr(VI) exposure including chromium production, chrome plating, leather work and work with Portland cement. The summary RR for all studies combined was 1.27 (95% CI 1.18 to 1.38). In analyses limited to only those studies identifying increased risks of lung cancer, the summary RR for stomach cancer was higher (RR=1.41, 95% CI 1.18 to 1.69). Overall, these results suggest that Cr(VI) is a stomach carcinogen in humans, which is consistent with the tumour results reported in rodent studies. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://group.bmj.com/group/rights-licensing/permissions.

Speciation of Cr(VI) in environmental samples in the vicinity of the ferrochrome smelter

Energy Technology Data Exchange (ETDEWEB)

Sedumedi, Hilda N. [Department of Chemistry, Tshwane University of Technology, P.O. Box 56208, Arcadia, 0007, Pretoria (South Africa); Mandiwana, Khakhathi L., E-mail: MandiwanaKL@tut.ac.za [Department of Chemistry, Tshwane University of Technology, P.O. Box 56208, Arcadia, 0007, Pretoria (South Africa); Ngobeni, Prince; Panichev, Nikolay [Department of Chemistry, Tshwane University of Technology, P.O. Box 56208, Arcadia, 0007, Pretoria (South Africa)

2009-12-30

The impact of ferrochrome smelter on the contamination of its environment with toxic hexavalent chromium, Cr(VI), was assessed by analyzing smelter dusts, soil, grass and tree barks. For the separation of Cr(VI) from Cr(III), solid samples were treated with 0.1 M Na{sub 2}CO{sub 3} and filtered through hydrophilic PDVF 0.45 {mu}m filter prior to the determination of Cr(VI) by electrothermal atomic absorption spectrometry (ET-AAS). Ferrochrome smelter dust was found to contain significant levels of Cr(VI), viz. 43.5 {mu}g g{sup -1} (cyclone dust), 2710 {mu}g g{sup -1} (fine dust), and 7800 {mu}g g{sup -1} (slimes dust) which exceeded the maximum acceptable risk concentration (20 {mu}g g{sup -1}). The concentration of Cr(VI) in environmental samples of grass (3.4 {+-} 0.2), soil (7.7 {+-} 0.2), and tree bark (11.8 {+-} 1.2) collected in the vicinity of the chrome smelter were higher as compared with the same kind of samples collected from uncontaminated area. The results of the investigation show that ferrochrome smelter is a source of environmental pollution with contamination factors of Cr(VI) ranging between 10 and 50.

Qualification and Flight Test of Non-Chrome Primers for C-130 Aircraft

Science.gov (United States)

2011-08-17

system  Significant hexavalent chrome reduction in finish system  Potential exposure level of spray applied chromated conversion coating not as...Lockheed Martin Aeronautics Company Qualification and Flight Test of Non- Chrome Primers for C-130 Aircraft Scott Jones Lockheed Martin...00-2011 to 00-00-2011 4. TITLE AND SUBTITLE Qualification and Flight Test of Non- Chrome Primers for C-130 Aircraft 5a. CONTRACT NUMBER 5b. GRANT

Hexavalent Chrome Free Coatings for Electronics: Electromagnetic Interference (EMI) Shielding Effectiveness (SE)

Science.gov (United States)

Kessel, Kurt R.

2016-01-01

Determine the suitability of trivalent chromium conversion coatings that meet the requirements of MIL-DTL-5541, Type II, for use in applications where high-frequency electrical performance is important. Evaluate the ability of hexavalent chrome free pretreated aluminum to form adequate EMI seals, and maintain that seal while being subjected to harsh environmental conditions. Assess the performance of trivalent chromium pretreatments against a known control hexavalent chrome pretreatment before and after they have been exposed to a set of environmental conditions. It is known that environmental testing causes a decrease in shielding effectiveness when hexavalent chrome pretreatments are used (Alodine 1200s). Need to determine how shielding effectiveness will be affected with the use of hexavalent chrome free pretreatments. Performance will be assessed by evaluating shielding effectiveness (SE) test data from a variety of test samples comprised of different aluminum types and/or conversion coatings. The formation of corrosion will be evaluated between the mating surfaces and gasket to assess the corrosion resistant properties of the pretreatments, comparing the hexavalent control to the hexavalent chrome free pretreatments.

Hexavalent Chrome Free Coatings for Electronics Applications: Joint Test Report

Science.gov (United States)

Rothgeb, Matt; Kessel, Kurt

2013-01-01

The overall objective of the Hexavalent Chrome Free Coatings for Electronics Applications project is to evaluate and test pretreatments not containing hexavalent chrome in avionics and electronics housing applications. This objective will be accomplished by testing strong performing coating systems from prior NASA and DoD testing or new coating systems as determined by the stakeholders.

Removal of Cr(VI) from aqueous solution by fungal biomass

Energy Technology Data Exchange (ETDEWEB)

Ahluwalia, Sarabjeet Singh [Department of Biotechnology, General Shivdev Singh Diwan Gurbachan Singh Khalsa College, Patiala, Punjab (India); Goyal, Dinesh [Department of Biotechnology and Environmental Sciences, Thapar University, Patiala, Punjab (India)

2010-10-15

Chromium compounds are released by industrial processes including leather production, mining, petroleum refining, in textile industry and dyeing. They are a significant threat to the environment and public health because of their toxicity. Removal of hexavalent chromium by living biomass of different fungi was effective in the order of Aspergillus terricola>Aspergillus niger>Acremonium strictum>Aureobasidium pullulans>Paecilomyces variotii>Aspergillus foetidus>Cladosporium resinae>Phanerochaete chrysosporium. Non-living dried fungal biomass showed higher potential for metal removal than living cells. Among all fungi dead biomass of P. chrysosporium, C. resinae and P. variotii had the maximum specific chromium uptake capacity, which was 11.02, 10.69 and 10.35 mg/g of dry biomass respectively at pH 4.0-5.0 in batch sorption. Removal of Cr(VI) by P. chrysosporium from multi-metallic synthetic solution as well as chrome effluent was significant by bringing down the residual concentration to 0.1 mg/L in the effluent, which falls within the permissible range and its removal was not affected by the presence of other metal ions such as Fe, Zn and Ni. Fourier transform infrared spectral analysis revealed the presence of carboxylate (C=O) and amine (-NH{sup +}{sub 3}-NH{sup +}{sub 2}) functional groups commonly present on the cell surface of all fungi, with possible involvement in chromium binding. The result indicates that non-living fungal biomass either obtained as a by-product of fermentation industry or mass produced using inexpensive culture media can be used for bioremediation of Cr(VI) from chrome effluent on large scale. (Copyright copyright 2010 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Facile synthesis of amino-functionalized titanium metal-organic frameworks and their superior visible-light photocatalytic activity for Cr(VI) reduction

International Nuclear Information System (INIS)

Wang, Hou; Yuan, Xingzhong; Wu, Yan; Zeng, Guangming; Chen, Xiaohong; Leng, Lijian; Wu, Zhibin; Jiang, Longbo; Li, Hui

2015-01-01

Highlights: • NH 2 functionalized MIL-125(Ti) was fabricated by a facile solvothermal method. • The photocatalyst could reduce Cr(VI)–Cr(III) under visible light irradiation. • The Ti 3+ –Ti 4+ intervalence electron transfer is important for Cr(VI) reduction. • Used NH 2 -MIL-125(Ti) can be recycled for the photocatalytic reduction. - Abstract: Porous metal-organic frameworks (MOFs) have been arousing a great interest in exploring the application of MOFs as photocatalyst in environment remediation. In this work, two different MOFs, Ti-benzenedicarboxylate (MIL-125(Ti)) and amino-functionalized Ti-benzenedicarboxylate (NH 2 -MIL-125(Ti)) were successfully synthesized via a facile solvothermal method. The MIL-125(Ti) and NH 2 -MIL-125(Ti) were well characterized by XRD, SEM, XPS, N 2 adsorption–desorption measurements, thermogravimetric analysis and UV–vis diffuse reflectance spectra (DRS). It is revealed that the NH 2 -MIL-125(Ti) has well crystalline lattice, large surface area and mesoporous structure, chemical and thermal stability, and enhanced visible-light absorption up to 520 nm, which was associated with the chromophore (amino group) in the organic linker. Compared with MIL-125(Ti), NH 2 -MIL-125(Ti) exhibited more efficient photocatalytic activity for Cr(VI) reduction from aqueous solution under visible-light irradiation. The addition of hole scavenger, the hole scavenger concentration and the pH value of the reaction solution played important roles in the photo-catalytic reduction of Cr(VI). The presence of Ti 3+ –Ti 4+ intervalence electron transfer was the main reason for photo-excited electrons transportation from titanium-oxo clusters to Cr(VI), facilitating the Cr(VI) reduction under the acid condition. It was demonstrated that amino-functionalized Ti(IV)-based MOFs could be promising visible-light photocatalysts for the treatment of Cr(VI)-contained wastewater

THE CHROME-TANNED GOAT LEATHER FOR HIGH QUALITY OF BATIK

Directory of Open Access Journals (Sweden)

W. Pancapalaga

2015-09-01

Full Text Available in which the first stage aimed to evaluate sodium silica as batik wax releasing agent on chrome leather.Completely randomized design (CRD was applied in this study. The concentration of sodium silica wastreated as treatments, in which Tl = 0, T2 = 2 g/L, T3: 4 g/L and T4 = 6 g/L. The second stage of thestudy was aimed to evaluate the type of dye used in batik method dyeing on chrome-tanned goat leather.CRD was used and the treatments were types of dye, i.e. T'1 = acid, T'2= indigosol, T'3 = napthol, T'4 =remazol. In both studies, 9 replicates were applied for each treatment. The use of sodium silicateconcentration of 2 g/L resulted in the percentage of release wax of 91.4% and did not degrade the qualityof chrome leather. The type of acid dyes and naphthol provided the best adhesion and color brightnessand resistance to washing treatment, water, sweat, bend, and rub at 4/5 to 5 on a scale of gray. Inconclusion, chrome tanned goat leather with batik dyeing method was recommended to become one ofthe raw materials of leather goods.

Syndeformation Chrome Spinels Inclusions in the Plastically Deformed Olivine Aggregates (Kraka Ophiolites, the Southern Urals

Directory of Open Access Journals (Sweden)

D. E. Saveliev

2015-12-01

Full Text Available This article presents the results of structural, petrographic, mineralogical and chemical studies of dunite veinlets in spinel peridotite from the Kraka ophiolites. It is demonstrated that plastic deformation of polycrystalline olivine, which form dunite, was accompanied by precipitation of impurities (aluminum and chrome as newly formed chrome spinels. The thinnest acicular inclusions of 0.3-0.5 micron thick are aligned in olivine grains along [010] axis. Bigger elongated irregular chrome spinel grains usually occur along grain and sub-grain olivine boundaries, and, occasionally, inside the grains along [100] axis. Alteration from the fine xenomorphic grains of chrome spinels to the bigger idiomorphic crystals was observed. Analogically to dynamic ageing (dispersion hardening in metals, the structural and chemical alterations in dunites are interpreted as deformation induced segregation of impurities. It is suggested that the euhedral chrome spinel grains typical for ophiolitic dunites were formed by coalescence and spheroidization. This process may be a key factor in the formation of ophiolitic chrome ore deposits.

Treatment of hexavalent chromium Cr (VI) in tanning effluent

International Nuclear Information System (INIS)

Ahmed, I.; Ali, S.

1999-01-01

Most common chemical used in chrome tanning is basic chromium sulphate (BCS). Manufacturing of BCS involves many steps producing liquid waste. Waste generated at every stage contains Cr (VI), which must be reduced to Cr (III) before being disposed to the environment. Different methods were studied for the reduction of toxic Cr (III). Pickle liquor (waste of electroplating industry) can also be used for the reduction of hexavalent chromium Cr (vi) along with other reducing materials / chemicals. In an electroplating process metal is treated with HCl or H/sub 2/SO/sub 4/ to remove scales and rust, the pickled items are then washed with water, washing contains FeCl/sub 2/ or fees/sub 4/ respectively called pickle liquor. During waste treatment pH adjustment to 6.0 - 9.0 and settling the sludge, is discharged to the lagoon. The sludge obtained is dried and disposed off in landfills. Other reducing agents like sodium bisulphite and sulfur dioxide were also studied, but pickle liquor was found to be more effective and economical. (author)

Novel Chemical Process for Producing Chrome Coated Metal

OpenAIRE

Pelar, Christopher; Greenaway, Karima; Zea, Hugo; Wu, Chun-Hsien; Luhrs, Claudia C.; Phillips, Jonathan

2018-01-01

The article of record as published may be found at http://dx.doi.org/10.3390/ma11010078 This work demonstrates that a version of the Reduction Expansion Synthesis (RES) process, Cr-RES, can create a micron scale Cr coating on an iron wire. The process involves three steps. I. A paste consisting of a physical mix of urea, chrome nitrate or chrome oxide, and water is prepared. II. An iron wire is coated by dipping. III. The coated, and dried, wire is heated to ~800 ◦C for 10 min in a tube fu...

Electrodeposition of Nanocrystalline Co-P Coatings as a Hard Chrome Alternative (Briefing Charts)

Science.gov (United States)

2011-02-10

chrome plating utilizes chromium in the hexavalent state (Cr6+) Cr6+ is a known carcinogen and poses a health risk to operators OSHA lowered the Cr6+ PEL...from 52 µg/m3 to 5 µg/m3 8 Apr 09, Memorandum, DoD Directive Hexavalent Chromium Management Policy NAVAIR Cr6+ Authorization Process Hard Chrome ...Aerospace & Defense February 10, 2011 Electrodeposition of Nanocrystalline Co-P Coatings as a Hard Chrome Alternative Jack Benfer Co-PI NAVAIR

Treatment of hexavalent chrome by bacteria. Saikin ni yoru rokka kuromu no shori

Energy Technology Data Exchange (ETDEWEB)

Otake, H [Hiroshima University, Hiroshima (Japan). Faculty of Engineering

1993-08-01

A biological reduction method in which hazardous hexavalent chrome is reduced by bacteria is explained as one of the bioremediation technologies. Those bacteria are separated from active sludge in the urban sewage treatment plant. The hexavalent chrome-reducing bacteria were isolated by cultivating the sludge. They were Enterobacter cloacae which are intestinal bacteria. Then, they were named HO1 stock. As a result of analyzing the reduction mechanism, it was made clear that the function is localized in the cellular endosporium and that the reduction is made by utilizing the electronic transfer system of endosporium. Under both aerobic and anaerobic conditions, they convert the hexavalent chrome into the trivalent chrome outside the cells. As a result of test, it was known that 5mM hexavalent chrome can be treated in one day. A quick reduction was confirmed also through an experiment in which carbon source was added to the industrial wastewater. If used for the treatment of sludge/water contaminated by hexavalent chrome, the present reduction by bacteria has the following advantages: The highest reduction rate is given near pH=7 at ordinary temperatures. It is not necessary to add chemicals. Energy is not needed. It is a disadvantageous fact that the present bacteria, if exposed to oxygen, become inactive. 18 refs., 5 figs.

Facile synthesis of amino-functionalized titanium metal-organic frameworks and their superior visible-light photocatalytic activity for Cr(VI) reduction

Energy Technology Data Exchange (ETDEWEB)

Wang, Hou [College of Environmental Science and Engineering, Hunan University, Changsha 410082 (China); Key Laboratory of Environment Biology and Pollution Control, Hunan University, Ministry of Education, Changsha 410082 (China); Yuan, Xingzhong, E-mail: yxz@hnu.edu.cn [College of Environmental Science and Engineering, Hunan University, Changsha 410082 (China); Key Laboratory of Environment Biology and Pollution Control, Hunan University, Ministry of Education, Changsha 410082 (China); Wu, Yan [College of Environment and Energy, South China University of Technology, Guangzhou 510006 (China); Zeng, Guangming [College of Environmental Science and Engineering, Hunan University, Changsha 410082 (China); Key Laboratory of Environment Biology and Pollution Control, Hunan University, Ministry of Education, Changsha 410082 (China); Chen, Xiaohong [School of Business, Central South University, Changsha 410083 (China); Leng, Lijian; Wu, Zhibin; Jiang, Longbo [College of Environmental Science and Engineering, Hunan University, Changsha 410082 (China); Key Laboratory of Environment Biology and Pollution Control, Hunan University, Ministry of Education, Changsha 410082 (China); Li, Hui [Institute of Bio-energy, Hunan Academy of Forestry, Changsha 410004 (China)

2015-04-09

Highlights: • NH{sub 2} functionalized MIL-125(Ti) was fabricated by a facile solvothermal method. • The photocatalyst could reduce Cr(VI)–Cr(III) under visible light irradiation. • The Ti{sup 3+}–Ti{sup 4+} intervalence electron transfer is important for Cr(VI) reduction. • Used NH{sub 2}-MIL-125(Ti) can be recycled for the photocatalytic reduction. - Abstract: Porous metal-organic frameworks (MOFs) have been arousing a great interest in exploring the application of MOFs as photocatalyst in environment remediation. In this work, two different MOFs, Ti-benzenedicarboxylate (MIL-125(Ti)) and amino-functionalized Ti-benzenedicarboxylate (NH{sub 2}-MIL-125(Ti)) were successfully synthesized via a facile solvothermal method. The MIL-125(Ti) and NH{sub 2}-MIL-125(Ti) were well characterized by XRD, SEM, XPS, N{sub 2} adsorption–desorption measurements, thermogravimetric analysis and UV–vis diffuse reflectance spectra (DRS). It is revealed that the NH{sub 2}-MIL-125(Ti) has well crystalline lattice, large surface area and mesoporous structure, chemical and thermal stability, and enhanced visible-light absorption up to 520 nm, which was associated with the chromophore (amino group) in the organic linker. Compared with MIL-125(Ti), NH{sub 2}-MIL-125(Ti) exhibited more efficient photocatalytic activity for Cr(VI) reduction from aqueous solution under visible-light irradiation. The addition of hole scavenger, the hole scavenger concentration and the pH value of the reaction solution played important roles in the photo-catalytic reduction of Cr(VI). The presence of Ti{sup 3+}–Ti{sup 4+} intervalence electron transfer was the main reason for photo-excited electrons transportation from titanium-oxo clusters to Cr(VI), facilitating the Cr(VI) reduction under the acid condition. It was demonstrated that amino-functionalized Ti(IV)-based MOFs could be promising visible-light photocatalysts for the treatment of Cr(VI)-contained wastewater.

GSDO Program Hexavalent Chrome Alternatives: Final Pretreatments Test Report

Science.gov (United States)

Kessel, Kurt

2013-01-01

Hexavalent chrome free pretreatments should be considered for use on Ground Support Equipment (OSE) and Electrical Ground Support Equipment (EOSE). Both of the hexavalent chrome free pretreatments (Metalast TCP HF and SurTec 650C) evaluated by this project met, and in some instances exceeded, the requirements ofMIL-DTL-5541 "Chemical Conversion Coatings on Aluminum and Aluminum Alloys". For DC resistance measurements, both Metalast TCP HF and SurTec (!50C met initial requirements following assembly and in many cases continued to maintain passing readings for the duration of testing.

Selective coating for solar panels. [using black chrome and black nickel

Science.gov (United States)

Mcdonald, G. E. (Inventor)

1977-01-01

The energy absorbing properties of solar heating panels are improved by depositing a black chrome coating of controlled thickness on a specially prepared surface of a metal substrate. The surface is prepared by depositing a dull nickel on the substrate, and the black chrome is plated on this low emittance surface to a thickness between 0.5 micron and 2.5 microns.

Microstructural Evolution in Chroming Coatings Friction Pairs under Dry Sliding Test Conditions

Directory of Open Access Journals (Sweden)

Xin Wang

2018-01-01

Full Text Available The microstructures of subsurface layers of 20CrMnTi steel pins against chroming and nonchroming T10 under dry sliding tests were studied by means of OM (optical microscopy, XRD (X-ray diffraction, and SEM (scanning electron microscopy. Results showed that the chroming coating strengthened the disc surface and significantly affected microstructural evolution. Three layers—the matrix, deformation layer (DL, and surface layer (SL—formed in 20CrMnTi for the chroming T10. The matrix and deformation layer (DL formed in 20CrMnTi for the nonchroming T10. The formation of the microstructure was considered as a result of the shear deformation.

NASA TEERM Hexavalent Chrome Alternatives Projects

Science.gov (United States)

Kessel, Kurt; Rothgeb, Matt

2011-01-01

This slide presentation reviews the NASA project to select an alternative to hexavalent chrome in the aerospace industry. Included is a recent historic testing and research that the Agency has performed on (1) the external tank, (2) the shuttle orbiter, (3) the Shuttle Rocket Booster, and (4) the Space Shuttle Main Engine. Other related Technology Evaluation for Environmental Risk Mitigation (TEERM) projects are reviewed. The Phase I process of the project performed testing of alternatives the results are shown in a chart for different coating systems. International collaboration was also reviewed. Phase II involves further testing of pretreatment and primers for 6 and 12 months of exposure to conditions at Launch Pad and the beach. Further test were performed to characterize the life cycle corrosion of the space vehicles. A new task is described as a joint project with the Department of Defense to identify a Hex Chrome Free Coatings for Electronics.

Chemometrics models for assessment of oxidative stress risk in chrome-electroplating workers.

Science.gov (United States)

Zendehdel, Rezvan; Shetab-Boushehri, Seyed Vahid; Azari, Mansoor R; Hosseini, Vajihe; Mohammadi, Hamidreza

2015-04-01

Oxidative stress is the main cause of hexavalant chromium-induced damage in chrome electroplating workers. The main goal of this study is toxicity analysis and the possibility of toxicity risk categorizing in the chrome electroplating workers based on oxidative stress parameters as prognostic variables. We assessed blood chromium levels and biomarkers of oxidative stress such as lipid peroxidation, thiol (SH) groups and antioxidant capacity of plasma. Data were subjected to principle component analysis (PCA) and artificial neuronal network (ANN) to obtain oxidative stress pattern for chrome electroplating workers. Blood chromium levels increased from 4.42 ppb to 10.6 ppb. Induction of oxidative stress was observed by increased in lipid peroxidation (22.38 ± 10.47 μM versus 14.74 ± 4.82 μM, p chrome electroplaters. The result showed multivariate modeling can be interpreted as the induced biochemical toxicity in the workers exposed to hexavalent chromium. Different occupation groups were assessed on the basis of risk level of oxidative stress which could further justify proceeding engineering control measures.

NASA and ESA Collaboration on Hexavalent Chrome Alternatives - Pretreatments with Primers Screening Final Test Report

Science.gov (United States)

Rothgeb, Matthew J.; Kessel, Kurt R.

2015-01-01

Hexavalent chromium (hex chrome or Cr(VI)) is a widely used element within applied coating systems because of its self-healing and corrosion-resistant properties. The replacement of hex chrome in the processing of aluminum for aviation and aerospace applications remains a goal of great significance. Aluminum is the major manufacturing material of structures and components in the space flight arena. The National Aeronautics and Space Administration (NASA) and the European Space Agency (ESA) are engaged in a collaborative effort to test and evaluate alternatives to hexavalent chromium containing corrosion coating systems. NASA and ESA share common risks related to material obsolescence associated with hexavalent chromium used in corrosion-resistant coatings. In the United States, Occupational Safety and Health Administration (OSHA) studies have concluded that hexavalent chromium is carcinogenic and poses significant risk to human health. On May 5, 2011, amendments to the Defense Federal Acquisition Regulation Supplement (DFARS) were issued in the Federal Register. Subpart 223.73 prohibits contracts from requiring hexavalent chromium in deliverables unless certain exceptions apply. Subpart 252.223-7008 provides the contract clause prohibiting contractors and subcontractors from using or delivering hexavalent chromium in a concentration greater than 0.1 percent by weight for all new contracts associated with supplies, maintenance and repair services, and construction materials. ESA faces its own increasingly stringent regulations within European directives such as Registration, Evaluation, Authorization and Restriction of Chemical (REACH) substances and the Restriction of Hazardous Substances Directive (RoHS) which have set a mid-2017 sunset date for hexavalent chromium. NASA and ESA continue to search for an alternative to hexavalent chromium in coatings applications that meet their performance requirements in corrosion protection, cost, operability, and health and

SU-E-T-328: Dosimetric Impact of Cobalt-Chrome Stabilization Hardware in Paraspinal Radiation Therapy

International Nuclear Information System (INIS)

Tang, G; LoSasso, T; Saleh, Z; Mechalakos, J; Lim, S; Lovelock, D; Laufer, I; Bilsky, M; Yamada, J

2015-01-01

Purpose: Due to saturation, high density materials Result in an apparent density of 3.2 g/cm 3 in CT images. The true density of traditional titanium stabilization rods (∼4.4 g/cm 3 ) is typically ignored in treatment planning. This may not be acceptable for new cobalt-chrome rods with a density of 8.5 g/cm 3 . This study reports the dosimetric impact of cobalt-chrome rods in paraspinal radiotherapy. Methods: For titanium and cobalt-chrome rods, two planning studies were done for both IMRT and VMAT in Varian Eclipse using AAA. 1) The effect of planning without assigning the true rod density was assessed by comparing plans generated with the apparent density and recalculated with the true density for titanium and cobalt-chrome. 2) To test if TPS can compensate for high density rods during optimization. Furthermore, TPS calculation accuracy was verified using MapCheck for a single 20 x 10 cm 2 field. The MapCheck was incrementally shifted to achieve measurement resolution of 1 mm. Results: PTV coverage was ∼0.3% and ∼4.7% lower in plans that were recalculated with the true rod density of titanium and cobalt-chrome, respectively. PTV coverage can be maintained if the correct density is used in optimization. Measurements showed that TPS overestimated the dose locally by up to 11% for cobalt-chrome rods and up to 4% for titanium rods if the density is incorrect. With density corrected, maximum local differences of 6% and 3% were seen for cobalt-chrome and titanium rods, respectively. At 2 cm beneath a rod, electrons scattered from the side of the rod increased the lateral dose and diminished as depth increases. TPS was not able to account for this effect properly even with the true rod density assigned. Conclusion: Neglecting the true density of cobalt-chrome rods can cause under coverage to the PTV. Assigning the correct density during treatment planning can minimize unexpected decrease in PTV dose

Improvement of uptake of chrome tan on hide protein by basic oxides

International Nuclear Information System (INIS)

Nashya, E.H.A.; Aggiagh, A.E.; Khedra, M.H.; El-Sayeda, N.H.E.

2005-01-01

Three basic oxides were used to improve uptake of chrome tan as well as shrinkage temperature of the tanned leather. In addition, the skin quality is one of the most important factors taking into consideration. Three basic oxides, named magnesium oxide, manganese oxide and sodium bicarbonate. The process was optimized taking into the account the shaking rate, chrome concentration (%), initial ph, basic oxides concentration, temperature and contact time. The optimum conditions for exhaustion, fixation, shrinkage temperature as well as skin quality showed that agitation rate of 150 rpm, chrome concentration of 16%, initial ph of 2.5, basic oxide concentration of 4% magnesium oxide, temperature of 35 degree C and contact time of 24 hr. The best results obtained are 88% exhaustion, 90.03% fixation and 109 degree C shrinkage temperature in aqueous medium

Preparation of high exhaust chrome from leather shavings and hydrocarbons with its application in leather processing for green tanning technology

International Nuclear Information System (INIS)

Nawaz, H.R.; Solangi, B.A.; Nadeem, U.; Zehra, B.

2010-01-01

The use of chrome in tanning has made the remarkable advances to achieve the best quality and quantity of leather. But the chrome tanning process is associated with the generation of heavy metal containing solid wastes and toxic effluents. To solve the environmental issues we emphasized on the development of high exhaust chrome complex from chrome containing leather wastes that could minimize the toxic effluents up to negligible limit. Therefore in the synthetic process of chrome tanning material, the chrome shavings and the hydrocarbons have been utilized as a reductant as well as the potential masking intermediates. These chrome tanning materials have been prepared using leather shavings alone in product A, partial replacement of shavings by hydrocarbons for product B and then replacement of hydrocarbons by molasses for product C. The materials have been employed for the tanning of goat skins parallel to the commercial basic chromium sulfate (BCS). (author)

Chrome - Free Aluminum Coating System

Science.gov (United States)

Bailey, John H.; Gugel, Jeffrey D.

2010-01-01

This slide presentation concerns the program to qualify a chrome free coating for aluminum. The program was required due to findings by OSHA and EPA, that hexavalent chromium, used to mitigate corrosion in aerospace aluminum alloys, poses hazards for personnel. This qualification consisted of over 4,000 tests. The tests revealed that a move away from Cr+6, required a system rather than individual components and that the maximum corrosion protection required pretreatment, primer and topcoat.

Cr(VI) and Cr(III) removal from aqueous solution by raw and modified lignocellulosic materials: a review.

Science.gov (United States)

Miretzky, P; Cirelli, A Fernandez

2010-08-15

In aqueous systems, chromium usually exists in both trivalent and hexavalent oxidation states, being Cr(VI) of particular importance and concern due to its great toxicity. Industrial sources of Cr(VI) are leather tanning, mining of chrome ore, production of steel and alloys, etc. The most common conventional method for Cr(VI) removal is reduction to Cr(III) at pH 2.0 and precipitation of Cr (OH)(3) with lime at pH 9-10. The disadvantage of precipitation is the disposal of the solid waste. Adsorption of Cr by different low cost materials seems to be a suitable choice for wastewater treatment. Many by-products of agriculture have proved to be suitable low cost adsorbents for Cr(VI) and Cr(III) removal from water. Lignocellulosic residues, which include both wood residues and agricultural residues, have adsorption capacity comparable to other natural sorbents, but they have the advantage of very low or no cost, great availability and simple operational process. This study is a review of the recent literature on the use of natural and modified lignocellulosic residues for Cr adsorption. The Cr maximum adsorption capacity and the adsorption mechanism under different experimental conditions are reported when possibly. Copyright 2010 Elsevier B.V. All rights reserved.

Groundwater contaminated with hexavalent chromium [Cr (VI)]: a health survey and clinical examination of community inhabitants (Kanpur, India).

Science.gov (United States)

Sharma, Priti; Bihari, Vipin; Agarwal, Sudhir K; Verma, Vipin; Kesavachandran, Chandrasekharan N; Pangtey, Balram S; Mathur, Neeraj; Singh, Kunwar Pal; Srivastava, Mithlesh; Goel, Sudhir K

2012-01-01

We assessed the health effects of hexavalent chromium groundwater contamination (from tanneries and chrome sulfate manufacturing) in Kanpur, India. The health status of residents living in areas with high Cr (VI) groundwater contamination (N = 186) were compared to residents with similar social and demographic features living in communities having no elevated Cr (VI) levels (N = 230). Subjects were recruited at health camps in both the areas. Health status was evaluated with health questionnaires, spirometry and blood hematology measures. Cr (VI) was measured in groundwater samples by diphenylcarbazide reagent method. Residents from communities with known Cr (VI) contamination had more self-reports of digestive and dermatological disorders and hematological abnormalities. GI distress was reported in 39.2% vs. 17.2% males (AOR = 3.1) and 39.3% vs. 21% females (AOR = 2.44); skin abnormalities in 24.5% vs. 9.2% males (AOR = 3.48) and 25% vs. 4.9% females (AOR = 6.57). Residents from affected communities had greater RBCs (among 30.7% males and 46.1% females), lower MCVs (among 62.8% males) and less platelets (among 68% males and 72% females) than matched controls. There were no differences in leucocytes count and spirometry parameters. Living in communities with Cr (VI) groundwater is associated with gastrointestinal and dermatological complaints and abnormal hematological function. Limitations of this study include small sample size and the lack of long term follow-up.

Wear and creep of highly crosslinked polyethylene against cobalt chrome and ceramic femoral heads.

Science.gov (United States)

Galvin, A L; Jennings, L M; Tipper, J L; Ingham, E; Fisher, J

2010-10-01

The wear and creep characteristics of highly crosslinked ultrahigh-molecular-weight polyethylene (UHMWPE) articulating against large-diameter (36mm) ceramic and cobalt chrome femoral heads have been investigated in a physiological anatomical hip joint simulator for 10 million cycles. The crosslinked UHMWPE/ceramic combination showed higher volume deformation due to creep plus wear during the first 2 million cycles, and a steady-state wear rate 40 per cent lower than that of the crosslinked UHMWPE/cobalt chrome combination. Wear particles were isolated and characterized from the hip simulator lubricants. The wear particles were similar in size and morphology for both head materials. The particle isolation methodology used could not detect a statistically significant difference between the particles produced by the cobalt chrome and alumina ceramic femoral heads.

Development of technology of complex aluminum-silicon-chrome alloy with utilization of off grade raw materials

Directory of Open Access Journals (Sweden)

A. Mekhtiev

2015-01-01

Full Text Available Experimental studies on obtaining a complex aluminum-silicon-chrome alloy (FASCh from Karaganda high-ash coals and high-carbon ferrochromefines were carried out. A method for smelting low-carbon ferrochrome using aluminum-silicon-chrome alloy as a reductant is suggested.

NASA TEERM Hexavalent Chrome Alternatives Projects

Science.gov (United States)

Kessel, Kurt R.; Rothgeb, Matthew

2011-01-01

The overall objective of the Hex Chrome Free Coatings for Electronics project is to evaluate and test pretreatment coating systems not containing hexavalent chrome in avionics and electronics housing applications. This objective will be accomplished by testing strong performing coating systems from prior NASA and DoD testing or new coating systems as determined by the stakeholders. The technical stakeholders have agreed that this protocol will focus specifically on Class 3 coatings. Original Equipment Manufacturers (OEMs), depots, and support contractors have to be prepared to deal with an electronics supply chain that increasingly provides parts with lead-free finishes, some labeled no differently and intermingled with their SnPb counterparts. Allowance of lead-free components presents one of the greatest risks to the reliability of military and aerospace electronics. The introduction of components with lead-free terminations, termination finishes, or circuit boards presents a host of concerns to customers, suppliers, and maintainers of aerospace and military electronic systems such as: 1. Electrical shorting due to tin whiskers 2. Incompatibility of lead-free processes and parameters (including higher melting points of lead-free alloys) with other materials in the system 3. Unknown material properties and incompatibilities that could reduce solder joint reliability

Study of skin and mucous membrane disorders among workers engaged in the sodium dichromate manufacturing industry and chrome plating industry.

Science.gov (United States)

Singhal, Vijay Kumar; Deswal, Balbir Singh; Singh, Bachu Narayan

2015-01-01

Inhalation of dusts and fumes arising during the manufacture of sodium dichromate from chrome ore, chromic acid mist emitted during electroplating, and skin contact with chromate produce hazards to workers. (1) To elucidate the prevalence of skin and mucous membrane disorders among the workers engaged in the sodium dichromate manufacturing industry and chrome plating industry. (2) To know the relationship of prevalence with the duration of exposure to chrome mist, dust, and fumes. A cross-sectional study was conducted among all the workers engaged in sodium dichromate manufacturing and chrome plating from several industries situated near the Delhi-Haryana border in the districts of Faridabad and Sonepat of Haryana, India from January 01, 2014 to December 31, 2014. All the workers available from the concerned industries for the study were interviewed and medically examined after obtaining their informed consent. A total of 130 workers comprising 66 workers from the sodium dichromate manufacturing industry and 64 workers from the chrome plating industry were examined on a pretested schedule. Descriptive statistical methods (proportions, relative risk, and Chi-square test of significance with P value analyzed using Epi Info version 7). All the workers were found to be males and of the adult age group. Out of the total examined, 69.69% and 56.22% of the workers had disorders of the nasal mucous membrane in the sodium dichromate manufacturing industry and the chrome plating industry, respectively. 42.42% and 28.22% of the workers had perforation of the nasal septum in the sodium dichromate manufacturing industry and chrome plating industry, respectively. 6.06% and 3.12% workers had skin ulcers in the sodium dichromate manufacturing industry and chrome plating industry, respectively. Nasal irritation and rhinorrhea were the most commonly found symptoms in both the processes. 48.48% and 90.52% of the workers were using hand gloves in the sodium dichromate manufacturing

Safety evaluation of traces of nickel and chrome in cosmetics: The case of Dead Sea mud.

Science.gov (United States)

Ma'or, Ze'evi; Halicz, Ludwik; Portugal-Cohen, Meital; Russo, Matteo Zanotti; Robino, Federica; Vanhaecke, Tamara; Rogiers, Vera

2015-12-01

Metal impurities such as nickel and chrome are present in natural ingredients-containing cosmetic products. These traces are unavoidable due to the ubiquitous nature of these elements. Dead Sea mud is a popular natural ingredient of cosmetic products in which nickel and chrome residues are likely to occur. To analyze the potential systemic and local toxicity of Dead Sea mud taking into consideration Dead Sea muds' natural content of nickel and chrome. The following endpoints were evaluated: (Regulation No. 1223/20, 21/12/2009) systemic and (SCCS's Notes of Guidance) local toxicity of topical application of Dead Sea mud; health reports during the last five years of commercial marketing of Dead Sea mud. Following exposure to Dead Sea mud, MoS (margin of safety) calculations for nickel and chrome indicate no toxicological concern for systemic toxicity. Skin sensitization is also not to be expected by exposure of normal healthy skin to Dead Sea mud. Topical application, however, is not recommended for already nickel-or chrome-sensitized persons. As risk assessment of impurities present in cosmetics may be a difficult exercise, the case of Dead Sea mud is taken here as an example of a natural material that may contain traces of unavoidable metals. Copyright © 2015 The Authors. Published by Elsevier Inc. All rights reserved.

Optical Determination of Lead Chrome Green in Green Tea by Fourier Transform Infrared (FT-IR Transmission Spectroscopy.

Directory of Open Access Journals (Sweden)

Xiaoli Li

Full Text Available The potential of Fourier transform infrared (FT-IR transmission spectroscopy for determination of lead chrome green in green tea was investigated based on chemometric methods. Firstly, the qualitative analysis of lead chrome green in tea was performed based on partial least squares discriminant analysis (PLS-DA, and the correct rate of classification was 100%. And then, a hybrid method of interval partial least squares (iPLS regression and successive projections algorithm (SPA was proposed to select characteristic wavenumbers for the quantitative analysis of lead chrome green in green tea, and 19 wavenumbers were obtained finally. Among these wavenumbers, 1384 (C = C, 1456, 1438, 1419(C = N, and 1506 (CNH cm-1 were the characteristic wavenumbers of lead chrome green. Then, these 19 wavenumbers were used to build determination models. The best model was achieved by least squares support vector machine (LS-SVMalgorithm with high coefficient of determination and low root-mean square error of prediction set (R2p = 0.864 and RMSEP = 0.291. All these results indicated the feasibility of IR spectra for detecting lead chrome green in green tea.

A conceptual model for determining career choice of CHROME alumna based on farmer's conceptual models

Science.gov (United States)

Moore, Lisa Simmons

This qualitative program evaluation examines the career decision-making processes and career choices of nine, African American women who participated in the Cooperating Hampton Roads Organization for Minorities in Engineering (CHROME) and who graduated from urban, rural or suburban high schools in the year 2000. The CHROME program is a nonprofit, pre-college intervention program that encourages underrepresented minority and female students to enter science, technically related, engineering, and math (STEM) career fields. The study describes career choices and decisions made by each participant over a five-year period since high school graduation. Data was collected through an Annual Report, Post High School Questionnaires, Environmental Support Questionnaires, Career Choice Questionnaires, Senior Reports, and standardized open-ended interviews. Data was analyzed using a model based on Helen C. Farmer's Conceptual Models, John Ogbu's Caste Theory and Feminist Theory. The CHROME program, based on its stated goals and tenets, was also analyzed against study findings. Findings indicated that participants received very low levels of support from counselors and teachers to pursue STEM careers and high levels of support from parents and family, the CHROME program and financial backing. Findings of this study also indicated that the majority of CHROME alumna persisted in STEM careers. The most successful participants, in terms of undergraduate degree completion and occupational prestige, were the African American women who remained single, experienced no critical incidents, came from a middle class to upper middle class socioeconomic background, and did not have children.

Groundwater contaminated with hexavalent chromium [Cr (VI]: a health survey and clinical examination of community inhabitants (Kanpur, India.

Directory of Open Access Journals (Sweden)

Priti Sharma

Full Text Available BACKGROUND: We assessed the health effects of hexavalent chromium groundwater contamination (from tanneries and chrome sulfate manufacturing in Kanpur, India. METHODS: The health status of residents living in areas with high Cr (VI groundwater contamination (N = 186 were compared to residents with similar social and demographic features living in communities having no elevated Cr (VI levels (N = 230. Subjects were recruited at health camps in both the areas. Health status was evaluated with health questionnaires, spirometry and blood hematology measures. Cr (VI was measured in groundwater samples by diphenylcarbazide reagent method. RESULTS: Residents from communities with known Cr (VI contamination had more self-reports of digestive and dermatological disorders and hematological abnormalities. GI distress was reported in 39.2% vs. 17.2% males (AOR = 3.1 and 39.3% vs. 21% females (AOR = 2.44; skin abnormalities in 24.5% vs. 9.2% males (AOR = 3.48 and 25% vs. 4.9% females (AOR = 6.57. Residents from affected communities had greater RBCs (among 30.7% males and 46.1% females, lower MCVs (among 62.8% males and less platelets (among 68% males and 72% females than matched controls. There were no differences in leucocytes count and spirometry parameters. CONCLUSIONS: Living in communities with Cr (VI groundwater is associated with gastrointestinal and dermatological complaints and abnormal hematological function. Limitations of this study include small sample size and the lack of long term follow-up.

Chitosan supramolecularly cross linked with trimesic acid - Facile synthesis, characterization and evaluation of adsorption potential for chromium(VI).

Science.gov (United States)

Bhatt, Ronak; Sreedhar, B; Padmaja, P

2017-11-01

A facile synthesis of Chitosan Supramolecularly cross-linked with Trimesic Acid (CTMA) is reported in this work. The adsorption potential of CTMA for removal of hexavalent chromium was evaluated and the influence of pH, temperature, contact time and adsorbent dose on the adsorption process was investigated. The experimental results showed that CTMA could efficiently adsorb Cr 6+ and partially reduce it to the less toxic Cr 3+ state. The maximum adsorption capacity of CTMA for Cr 6+ was found to be 129.53mg/g at pH 2.0. CTMA and chromium loaded CTMA were characterised by FT-IR, Raman, TGA-DSC, SEM-EDX, XRD, ESR and XPS spectroscopic techniques. Chitosan was observed to be cross- linked with TMA via ionic, hydrogen bonding and pi-pi supramolecular interactions while adsorption of chromium onto CTMA was by electrostatic forces and hydrogen bonding. From the observed results it was evident that CTMA was successfully applied for simultaneous removal of chromium, lead and iron from chrome plating effluent. Copyright © 2017 Elsevier B.V. All rights reserved.

Synthesis of Citric-Acrylate Oligomer and its in-Situ Reaction with Chrome Tanned Collagen (hide powder)

International Nuclear Information System (INIS)

Haroun, A.A.; Masoud, R.A.; Bronco, S.; Ciardelli, F.

2005-01-01

The purpose of this study was to formulate the new combined system of acrylic and citric acids, which has been prepared by free radical polymerization and esterification reaction at the same time to form citric acrylate (CAC) oligomer through ester linkage and low molecular weight (Mw 2241), in compared with polyacrylic acid. The chemical structure and the reaction mechanism of this oligomer were confirmed by different spectroscopic tools (1 H , 13 C-NMR, ATR-IR), gel permeation chromatography and thermogravimetric analysis (TGA/DTA). The problem of the effect of the masking agents in the chrome tanning of the collagen and the pickling of the hide has been approached from the study of the hydrothermal and mechanical properties, using this new eco-friendly oligomer, which was carried out in-situ treated/grafted chrome tanned collagen (hide powder), and pickled hide. The microemulsion grafting copolymerization of (CAC) using 2.2-azo-bis isobutyronitrile (ABIN), via direct coupling reaction, onto the chrome tanned collagen showed that the free amino groups of the collagen were considered to be a potential site for the in-situ reaction with (CAC) oligomer. Also, using of citric-acrylate (CAC) oligomer, during chrome tanning of leather, instead of the traditional strong acids (sulfuric, hydrochloric and formic) resulted in significant improvement in chrome exhaustion and physical properties

Le chrome en milieu marin

OpenAIRE

Chiffoleau, Jean-francois

1994-01-01

Le présent document constitue une synthèse des connaissances sur le cycle biogéochimique du chrome. Les sources naturelles et anthropiques sont étudiées, les échanges entre les différents compartiments géochimiques sont évalués, avec une attention particulière portée à la quantification des apports aussi bien des fleuves que de l'atmosphère au milieu marin. Les niveaux de concentration dans ces compartiments sont évalués, et montrent que l'on rencontre dans certaines régions des contamination...

Validation of HVOF WC/Co Thermal Spray Coatings as a Replacement for Hard Chrome Plating on Aircraft Landing Gear

National Research Council Canada - National Science Library

Sartwell, Bruce

2004-01-01

.... However, chrome plating utilizes hexavalent chromium, which is a highly toxic carcinogen, and increasingly stringent environmental and worker-safety regulations are making chrome plating more expensive for the DoD...

Ni–Mo–Co ternary alloy as a replacement for hard chrome

Energy Technology Data Exchange (ETDEWEB)

Srivastava, Meenu, E-mail: meenu_srivas@yahoo.co.uk; Anandan, C.; Grips, V.K. William

2013-11-15

Hard chrome is the most extensively used electroplated coating in the aerospace and automotive industries due to its attractive properties such as high hardness and excellent wear resistance. However, due to the health risks associated with the use of hexavalent chromium baths during electroplating, there is a need to identify an alternative to this coating. In this study a nickel–molybdenum alloy with cobalt as the alloying element has been developed. The coating was characterized for its micro hardness, wear resistance, coefficient of friction and corrosion resistance. The coating was also subjected to heat treatment at temperatures in the range of 200°–600 °C. It was observed that the micro hardness of Ni–Mo–Co (730 KHN) alloy coating under optimized conditions is apparently quiet similar to that of the most probable substitute Co–P (745 VHN) and hard chrome (800 VHN) coatings. The tribological properties like the wear rate and coefficient of friction of the 400 °C heat treated Ni–Mo–Co coating were noticed to be better compared to hard chrome coating. The electrochemical impedance and polarization studies showed that the corrosion resistance of heat treated Ni–Mo–Co alloy was better than as-deposited Ni–Mo–Co and Ni–Mo coating.

Ni–Mo–Co ternary alloy as a replacement for hard chrome

International Nuclear Information System (INIS)

Srivastava, Meenu; Anandan, C.; Grips, V.K. William

2013-01-01

Hard chrome is the most extensively used electroplated coating in the aerospace and automotive industries due to its attractive properties such as high hardness and excellent wear resistance. However, due to the health risks associated with the use of hexavalent chromium baths during electroplating, there is a need to identify an alternative to this coating. In this study a nickel–molybdenum alloy with cobalt as the alloying element has been developed. The coating was characterized for its micro hardness, wear resistance, coefficient of friction and corrosion resistance. The coating was also subjected to heat treatment at temperatures in the range of 200°–600 °C. It was observed that the micro hardness of Ni–Mo–Co (730 KHN) alloy coating under optimized conditions is apparently quiet similar to that of the most probable substitute Co–P (745 VHN) and hard chrome (800 VHN) coatings. The tribological properties like the wear rate and coefficient of friction of the 400 °C heat treated Ni–Mo–Co coating were noticed to be better compared to hard chrome coating. The electrochemical impedance and polarization studies showed that the corrosion resistance of heat treated Ni–Mo–Co alloy was better than as-deposited Ni–Mo–Co and Ni–Mo coating.

Elevated Frequencies of Micronuclei and other Nuclear Abnormalities of Chrome Plating Workers Occupationally Exposed to Hexavalent Chromium.

Science.gov (United States)

Sudha, S; Kripa, S K; Shibily, P; Shyn, J

2011-01-01

Biomonitoring provides a useful tool to estimate the genetic risk from exposure to genotoxic agents. The aim of this study was to assess the potential cytogenetic damage associated with occupational exposure to hexavalent chromium by using micronuclei (MN) as a biomarker. This was a cross-sectional study and all participants were males. Both the exposed and control individuals were selected from Coimbatore, Southern India. Exfoliated buccal cells from 44 chrome plating workers and 40 age and sex matched control subjects were examined for MN frequency and nuclear abnormalities (NA) other than micronuclei, such as binucleates, broken eggs, karyorrhexis, karyolysis and pyknosis. Results showed statistically significant difference between chrome plating workers and control groups. MN and NA frequencies in chrome plating workers were significantly higher than those in control groups (p chrome plating workers are under risk of significant cytogenetic damage. Therefore, there is a need to educate those who work with heavy metals about the potential hazard of occupational exposure and the importance of using protective measures.

Weight of Polyethylene Wear Particles is Similar in TKAs with Oxidized Zirconium and Cobalt-chrome Prostheses

Science.gov (United States)

Kim, Jun-Shik; Huh, Wansoo; Lee, Kwang-Hoon

2009-01-01

Background The greater lubricity and resistance to scratching of oxidized zirconium femoral components are expected to result in less polyethylene wear than cobalt-chrome femoral components. Questions/purposes We examined polyethylene wear particles in synovial fluid and compared the weight, size (equivalent circle diameter), and shape (aspect ratio) of polyethylene wear particles in knees with an oxidized zirconium femoral component with those in knees with a cobalt-chrome femoral component. Patients and Methods One hundred patients received an oxidized zirconium femoral component in one knee and a cobalt-chrome femoral component in the other. There were 73 women and 27 men with a mean age of 55.6 years (range, 44–60 years). The minimum followup was 5 years (mean, 5.5 years; range, 5–6 years). Polyethylene wear particles were analyzed using thermogravimetric methods and scanning electron microscopy. Results The weight of polyethylene wear particles produced at the bearing surface was 0.0223 ± 0.0054 g in 1 g synovial fluid in patients with an oxidized zirconium femoral component and 0.0228 ± 0.0062 g in patients with a cobalt-chrome femoral component. Size and shape of polyethylene wear particles were 0.59 ± 0.05 μm and 1.21 ± 0.24, respectively, in the patients with an oxidized zirconium femoral component and 0.52 ± 0.03 μm and 1.27 ± 0.31, respectively, in the patients with a cobalt-chrome femoral component. Knee Society knee and function scores, radiographic results, and complication rate were similar between the knees with an oxidized zirconium and cobalt-chrome femoral component. Conclusions The weight, size, and shape of polyethylene wear particles were similar in the knees with an oxidized zirconium and a cobalt-chrome femoral component. We found the theoretical advantages of this surface did not provide the actual advantage. Level of Evidence Level I, therapeutic study. See the guidelines for Authors for a complete

Effect of gamma radiation on chrome-tanned sheepskin

International Nuclear Information System (INIS)

Kaldirimci, C.

1982-01-01

Effect of 60 γ-radiation on chrome-tanned, blue-stock sheepskin was investigated. Radiation was applied between 0.35-10.5 Mrad and the resultant physical and mechanical changes were observed. Radiation did not change the water adsorption capability of leather but caused significant reductions in shrinkage temperature and tensile strength. The correlations between dose and radiation hazards were determined. (author)

Total control of chromium in tanneries - thermal decomposition of filtration cake from enzymatic hydrolysis of chrome shavings.

Science.gov (United States)

Kocurek, P; Kolomazník, K; Bařinová, M; Hendrych, J

2017-04-01

This paper deals with the problem of chromium recovery from chrome-tanned waste and thus with reducing the environmental impact of the leather industry. Chrome-tanned waste was transformed by alkaline enzymatic hydrolysis promoted by magnesium oxide into practically chromium-free, commercially applicable collagen hydrolysate and filtration cake containing a high portion of chromium. The crude and magnesium-deprived chromium cakes were subjected to a process of thermal decomposition at 650°C under oxygen-free conditions to reduce the amount of this waste and to study the effect of magnesium removal on the resulting products. Oxygen-free conditions were applied in order to prevent the oxidation of trivalent chromium into the hazardous hexavalent form. Thermal decomposition products from both crude and magnesium-deprived chrome cakes were characterized by high chromium content over 50%, which occurred as eskolaite (Cr 2 O 3 ) and magnesiochromite (MgCr 2 O 4 ) crystal phases, respectively. Thermal decomposition decreased the amount of chrome cake dry feed by 90%. Based on the performed experiments, a scheme for the total control of chromium in the leather industry was designed.

Development of CMOS MEMS inductive type tactile sensor with the integration of chrome steel ball force interface

Science.gov (United States)

Yeh, Sheng-Kai; Chang, Heng-Chung; Fang, Weileun

2018-04-01

This study presents an inductive tactile sensor with a chrome steel ball sensing interface based on the commercially available standard complementary metal-oxide-semiconductor (CMOS) process (the TSMC 0.18 µm 1P6M CMOS process). The tactile senor has a deformable polymer layer as the spring of the device and no fragile suspended thin film structures are required. As a tactile force is applied on the chrome steel ball, the polymer would deform. The distance between the chrome steel ball and the sensing coil would changed. Thus, the tactile force can be detected by the inductance change of the sensing coil. In short, the chrome steel ball acts as a tactile bump as well as the sensing interface. Experimental results show that the proposed inductive tactile sensor has a sensing range of 0-1.4 N with a sensitivity of 9.22(%/N) and nonlinearity of 2%. Preliminary wireless sensing test is also demonstrated. Moreover, the influence of the process and material issues on the sensor performances have also been investigated.

The Use Level of Chrome Tannage For Rabbit Fur Leather Observed on Tearing Strength, Stitch Tearing Strength, Water Absorption and Organoleptic

Directory of Open Access Journals (Sweden)

Mustakim Mustakim

2012-02-01

Full Text Available The purpose of this study was to find out the appropiate of chrome tannage level for rabbit fur leather quality. The result were expected to contribute information for many people who relate with tanning technology, especialy about the use level of chrome tannage for fur leather quality and could as patern to hold further research.The material that used were 12 pieces of three months of rabbit skin. The method is Completely Randomized Design, consist of three treatments of chrome tannage (Chromosal B, they were : B1 (Chromosal B 6%, B2 (Chromosal B 8%, and B3 (Chromosal B 10%. Each of treatment hold on four replications. The variables which measured are tearing strength, stitch teraing strength, water absorption and organoleptic consist of “kekuatan bulu”’ “kerataan bulu” and “kelemasan kulit” in fur leather. Data was analysed by analysis variance followed by Duncan’s Multiple Range Test. The result of this research show that the use level of chromosal B give very significant influence among tearing strength, stitch tearing strength and water absorption. It gave significant influence among the organoleptic test. Based on the result, can be concluded that 10 percent of chrome tannage (chromosal B, produce the best result on tearing strength, stitch tearing strength, water absorption and organoleptic for “kekuatan bulu” and “kerataan bulu”. The incrase of chrome tannage offer will decrease the “kelemasan kulit” in fur leather and the best “kelemasan kulit” produced by the lowest chrome tannage offer, that was 6 percent of Chromosal B. The best quality of rabbit fur leather produced by 10 percent of chrome tannage offer.   Keywords: chrome, tannage, fur leather

SUPERFUND TREATABILITY CLEARINGHOUSE: SOIL STABILIZATION PILOT STUDY, UNITED CHROME NPL SITE PILOT STUDY AND HEALTH AND SAFETY PROGRAM, UNITED CHROME NPL SITE PILOT STUDY

Science.gov (United States)

This document is a project plan for a pilot study at the United Chrome NPL site, Corvallis, Oregon and includes the health and safety and quality assurance/quality control plans. The plan reports results of a bench-scale study of the treatment process as iieasured by the ...

World Class Facilities Management

DEFF Research Database (Denmark)

Malmstrøm, Ole Emil; Jensen, Per Anker

2013-01-01

Alle der med entusiasme arbejder med Facilities Management drømmer om at levere World Class. DFM drømmer om at skabe rammer og baggrund for, at vi i Danmark kan bryste os at være blandt de førende på verdensplan. Her samles op på, hvor tæt vi er på at nå drømmemålet.......Alle der med entusiasme arbejder med Facilities Management drømmer om at levere World Class. DFM drømmer om at skabe rammer og baggrund for, at vi i Danmark kan bryste os at være blandt de førende på verdensplan. Her samles op på, hvor tæt vi er på at nå drømmemålet....

Analysis of KROTOS KS-2 and KS-4 steam explosion experiments with TEXAS-VI

Energy Technology Data Exchange (ETDEWEB)

Chen, Ronghua, E-mail: rhchen@mail.xjtu.edu.cn [State Key Laboratory of Multiphase Flow in Power Engineering, School of Nuclear Science and Technology, Xi’an Jiaotong University, Xi’an 710049 (China); Wang, Jun [Nuclear Engineering and Engineering Physics, College of Engineering, University of Wisconsin Madison, WI 53706 (United States); Su, G.H.; Qiu, Suizheng [State Key Laboratory of Multiphase Flow in Power Engineering, School of Nuclear Science and Technology, Xi’an Jiaotong University, Xi’an 710049 (China); Corradini, M.L., E-mail: Corradini@engr.wisc.edu [Nuclear Engineering and Engineering Physics, College of Engineering, University of Wisconsin Madison, WI 53706 (United States)

2016-12-01

Highlights: • The KS-2 and KS-4 steam explosion experiments were analyzed by TEXAS-VI. • The coarse mixing status up to the explosion triggering time was well predicted by TEXAS-VI. • The predicted dynamic explosion pressure was in good agreement with the experimental results. - Abstract: TEXAS-VI is a transient, three-field, one-dimensional mechanistic model for the steam explosion phenomena. A fuel solidification model and associated fragmentation criteria of the solidifying particle for both the mixing phase and explosion phase were developed and incorporated into TEXAS-VI to account for solidification. In the present study, TEXAS-VI was used to analyze the KS-2 and KS-4 steam explosion experiments, which were performed in the KROTOS facility as part of the OECD-SERENA-2 program. In the simulation, the KROTOS experimental facility was modeled as Eulerian control volumes based on the facility geometry. The molten corium jet was divided up into a series of LaGrangian master particles equal to the initial jet diameter. Both the mixing phase and the explosion phase of the experiments were simulated by TEXAS-VI. Comparison to test data indicates that the fuel jet kinematics and the vapor volume during the mixing phase were well predicted by TEXAS-VI. The TEXAS-VI prediction of the dynamic explosion pressure at different axial locations in the test was also in good agreement with the experimental results. The maximum pressure of KS-2 and KS-4 predicted by TEXAS-VI were 16.7 MPa and 41.9 MPa, respectively. The KS-4 maximum steam explosion pressure predicted by TEXAS-VI was higher than that of KS-2, which was consistent with experiment observation. The observed differences of the dynamic explosion pressure between the KS-2 and KS-4 experiments were also successfully simulated by TEXAS-VI. This suggests that TEXAS-VI is able to analyze the effect of prototypic melt compositions on the steam explosion phenomena. Additional benchmarking and evaluations are ongoing.

The Role of Diffusion Media in Nitriding Process on Surface Layers Characteristics of AISI 4140 with and without Hard Chrome Coatings

Directory of Open Access Journals (Sweden)

K.A. Widi

2016-09-01

Full Text Available The surface layer characteristics of the AISI 4140 tool steel treated by nitriding gas before and after hard chrome plating utilizing pure nitrogen diffusion media (fluidized bed reactor and the without gas (muffle reactor has been studied experimentally. The result shows that nitriding substrate with hard chrome layers has nitrogen atoms concentration almost twice greater than that without hard chrome layers. After being given a hard chrome plating, nitriding on AISI 4140 steel generally has a nitrogen concentration of up to 4 times more than the substrate without hard chrome coating. Almost the entire specimen showed the highest concentration of N atoms in the area below the surface (hardening depth of 200 to 450 µm. N atoms diffusion depth profile has a correlation with hardening depth profile, especially on the specimens layered with hard chromium. The substrate without hard chrome plating tends to have higher surface hardness than the sub-surface. The results show that the effectiveness and efficiency of the gas nitriding diffusion process can be produced without the use of gas in the muffle reactor but the specimens must be hard chromium coated first. This phenomenon can be explained by the role of the passive layer formation that works as a barrier to keeps the spreading of N atoms concentrated in sub-surface areas.

Solid-Phase Extraction of Trace Amounts of Uranium(VI in Environmental Water Samples Using an Extractant-Impregnated Resin Followed by Detection with UV-Vis Spectrophotometry

Directory of Open Access Journals (Sweden)

Ahmad Hosseini-Bandegharaei

2013-01-01

Full Text Available A stable extractant-impregnated resin (EIR containing Chrome Azurol B was prepared using Amberlite XAD-2010 as a porous polymeric support. The new EIR was employed for trace separation and preconcentration of U(VI ion followed by spectrophotometric determination with the arsenazo III procedure. CAB/XAD-2010 exhibited excellent selectivity for U(VI ion over coexisting ions. Experimental parameters including pH, contact time, shaking speed, and ionic strength were investigated by batch extraction methods. Maximum sorption of U(VI ions occurred at pH 4.3–6.9. The capacity of EIR was found to be 0.632 mmol·g−1. Equilibrium was reached in 25 min and the loading half-time, t1/2, was less than 6 min. The equilibrium adsorption isotherm of U(VI was fitted with the Langmuir adsorption model. In addition, a column packed with CAB/XAD-2010 was used for column-mode separation and preconcentration of U(VI ion. For the optimization of the dynamic procedure, effects of sample volume, sample and eluent flow rate, eluent concentration, and its volume were investigated. The preconcentration factors for U(VI were found out to be 160. But, for convenience, a preconcentration factor of 150 was utilized for the column-mode preconcentration. The dynamic procedure gave a detection limit of 5.0×10-10 mol·L−1 (0.12 μg·L−1 for U(VI ion. The proposed dynamic method showed good performance in analyzing environmental water samples.

Soybean plant growth study conducted using purified protein hydrolysate-based fertilizer made from chrome-tanned leather waste.

Science.gov (United States)

Pati, Anupama; Chaudhary, Rubina

2015-12-01

Leather processing discharges enormous amount of chrome containing leather solid waste which creates a major disposal problem. Chrome-tanned leather solid waste is a complex of collagen and chromium. The presence of chromium limits protein application in fertilizer industry. The purified protein hydrolysate with zero chromium could be used as a nitrogen source for fertilizer formulation. In this study, an attempt has been made to employ purified protein hydrolysate derived from chrome-tanned leather shavings (CTLS) in formulation of fertilizer. The formulated fertilizer (1–3 t ha(-1)) is employed as nitrogen source in production of soybean. Plant growth study demonstrates that formulated fertilizer dosage 3 t ha(-1) produced similar effects of commercial fertilizer-treated plants. Application of formulated fertilizer yielded higher seed in plant than commercial fertilizer.

Recovery and reuse of hexavalent chromium from aqueous solutions by a hybrid technique of electrodialysis and ion exchange

OpenAIRE

Gayathri, R.; Senthil Kumar, P.

2010-01-01

The chrome plating industry is one of the highly polluting industries whose effluent mainly consists of chromium(VI). This compound is highly toxic to aquatic life and human health. The rinse water constituents reflect the chrome plating bath characteristics; generally dead tank wash water contains about 1% of the plating bath concentration. Other metals and metal compounds usually considered as toxic can be precipitated out by suitably adjusting the pH of the wastewaters. However, Cr(VI) is ...

Mid-term survivorship and clinical outcomes of cobalt-chrome and oxidized zirconium on highly crosslinked polyethylene.

Science.gov (United States)

Petis, Stephen M; Vasarhelyi, Edward M; Lanting, Brent A; Howard, James L; Naudie, Douglas D R; Somerville, Lyndsay E; McCalden, Richard W

2016-02-01

The choice of bearing articulation for total hip arthroplasty in younger patients is amenable to debate. We compared mid-term patient-reported outcomes and survivorship across 2 different bearing articulations in a young patient cohort. We reviewed patients with cobalt-chrome or oxidized zirconium on highly crosslinked polyethylene who were followed prospectively between 2004 and 2012. Kaplan-Meier analysis was used to determine predicted cumulative survivorship at 5 years with all-cause and aseptic revisions as the outcome. We compared patient-reported outcomes, including the Harris hip score (HHS), Western Ontario and McMaster University Osteoarthritis Index (WOMAC) and Short-form 12 (SF-12) scores. A total of 622 patients were followed during the study period. Mean follow-up was 8.2 (range 2.0-10.6) years for cobalt-chrome and 7.8 (range 2.1-10.7) years for oxidized zirconium. Mean age was 54.9 ± 10.6 years for cobalt-chrome and 54.8 ± 10.7 years for oxidized zirconium. Implant survivorship was 96.0% (95% confidence interval [CI] 94.9%-97.1%) for cobalt-chrome and 98.7% (95% CI 98.0%-99.4%) for oxidized zirconium on highly crosslinked polyethylene for all-cause revisions, and 97.2% (95% CI 96.2%-98.2%) for cobalt-chrome and 99.0% (95% CI 98.4%-99.6%) for oxidized zirconium for aseptic revisions. An age-, sex- and diagnosis-matched comparison of the HHS, WOMAC and SF-12 scores demonstrated no significant changes in clinical outcomes across the groups. Both bearing surface couples demonstrated excellent mid-term survivorship and outcomes in young patient cohorts. Future analyses on wear and costs are warranted to elicit differences between the groups at long-term follow-up.

Selection of the Chrome Reduction Bacteria in the Waste of Tanning Leather Industries by Ozonization Method

International Nuclear Information System (INIS)

Yazid, M.; Aris Bastianudin; Widdi Usada

2007-01-01

Selection of the chrome reduction bacteria in the waste of tanning leather industries by ozonization method has been done. The objectives of this research was to obtain isolate bacteria from the waste with chrome contain, so that expected can be used for chrome bioremediation agent for arrange to improved the waste treatment for tanning leather industries. Selection of bacteria in the waste was carried out by ozonization method with time variation 0 to 210 minutes by time interval 15 minutes. Isolation bacteria was carried out was grown on the BHI media for 24 hours at 37°C temperature. So be inoculated by streak plate method on the TBX, MC, EA, CTM and BP media. Characterization of bacteria was done by saw the colonies morphology, sel morphology and biochemical characterization. So, identification of isolate bacteria by matching profile method. The result of this research can be obtained 5 isolate bacteria BCR1, BCR2, BCR3, BCR4 and BCR5 with the different phenotypic character. From the five isolate can be selected resistance ozon isolate until 180 minutes time ozonization were BCR 2, were identified belong to the genus of Bacillus. The examination results showed that the isolate bacteria be able to reduction of the chrome concentration in the waste of tanning leather industries by 71.03 %. Efficiency. (author)

Effect of current imbalance on stability of a cable-in-conduit conductor consisting of chrome-plated strands

International Nuclear Information System (INIS)

Koizumi, Norikiyo; Takahashi, Yoshikazu; Nishi, Masataka; Isono, Takaaki; Tsuji, Hiroshi; Ono, Michitaka; Hamajima, Takataro; Fujioka, Tsutomu.

1997-02-01

The effect of an unbalanced current distribution in a conductor consisting of chrome plated strands on stability was investigated using a cable-in-conduit conductor (CICC) consisting of 27 NbTi chrome-plated strands. In addition, the quench behavior when a non-uniform current distribution was produced in the conductor was studied from the experimental results. Moreover, impedance of the chrome-plated strands was measured using the sample conductor. The results show that the stability is determined by the largest strand current when it is sufficiently large otherwise by the transport current when it is not high enough. It was found that it took a long time to make the conductor quench from the onset of the normal transition of the strand carrying the large current. This is explained by the good diffusivity of the coolant temperature in the conductor's cross section. Since the ramp-rate limitation cannot probably take place if the coolant temperature is diffused well in the conductor's cross section, it is expected the ramp-rate limitation can be prevented using this effect. It is also shown that the chrome-plated strands come into contact with one another with uniform transverse conductance on the order of 10 3 S/m. (author)

Investigations on chemical-physical conditioning of ashes from the incineration of sewage sludge to deposit on surface landfill site; Untersuchungen zur Chemisch-Physikalischen Behandlung von Klaerschlammverbrennungsasche zur Ablagerung auf oberirdischen Deponien

Energy Technology Data Exchange (ETDEWEB)

Schneider, O.; Becker, A. [Technische Univ. Kaiserslautern (Germany). Fachgebiet Bodenmechanik und Grundbau; Scherer, G. [TERRAG Service und Vertrieb GmbH, Homburg (Germany)

2007-06-15

Depositing of ashes from the incineration of sewage sludge on landfill is possible after conditioning or within appropriate boxes. The partial high content of chromate- and dichromate- (chrome VI) concentration in the eluate of these slags can cause some difficulties. Presently, disposal of such slags is accomplished in underground spaces. Taking into account the provisions of national laws, possibility is limited. Therefore investigations on deposing of conditioned slags on surface landfills are of growing importance. The binders added to condition the incineration slags were chosen to assess the chemical change of hexavalent chrome (chrome VI) to indissoluble chrome (chrome III). Cement, SAV-residues as well as fly ash were taken as binders. The investigations presented refer to results on mechanical behaviour of conditioned slags. Emphasis is placed on the time-dependent behaviour of strength as well as on water permeability. Several cylindrical samples made by different compounds were tested within a period of about 112 days. Requirements with respect to strength were met within a few days. Demands on the eluate-criteria need additional investigations. (orig.)

Covalently bonded ionic liquid onto cellulose for fast adsorption and efficient separation of Cr(VI): Batch, column and mechanism investigation.

Science.gov (United States)

Dong, Zhen; Zhao, Long

2018-06-01

Combining the advantages of both cellulose and ionic liquid, ionic liquid functionalized cellulose (ILFC) as adsorbent was prepared through radiation grafting glycidyl methacrylate onto cellulose microsphere following by reaction with ionic liquid 1-aminopropyl-3-methyl imidazolium nitrate. Its adsorption properties towards Cr(VI) were investigated in batch and column experiments. In batch experiments, the adsorption kinetics was well fitted with pseudo-second-order mode with equilibrium time of 2 h and the adsorption capacity reached 181.8 mg/g at pH 2 calculated from Langmuir model. In fixed column, both Yoon-Nelson and Thomas models gave satisfactory fit to experimental data and breakthrough curves, and equilibrium adsorption capacity calculated by Thomas model was 161.0 mg/g. Moreover, ILFC exhibited high selectivity towards Cr(VI) even in synthetic chrome-plating wastewater. Besides, adsorption/desorption test revealed ILFC can be regenerated and reused several times without obvious decrease in adsorbed amount. The adsorption process was demonstrated to anion exchange-reduction mechanism via XPS analysis. Copyright © 2018 Elsevier Ltd. All rights reserved.

Chromatographic characterization of products isolated from chrome shavings

Directory of Open Access Journals (Sweden)

Edivaldo E Garcia

1999-01-01

Full Text Available Gel permeation chromatography and high performance liquid chromatography were employed for separation and chemical characterization of products isolated from chrome shavings. After enzymatic hydrolysis, the products isolated were peptides of higher molecular weight. Peptides of lower molecular weight and free aminoacids were the main products using sulfuric acid in chrome shavings solubilization. Glycine (17% , glutamic acid (10.6% , alanine (9.2% , and arginine (8.2% were the principal amino acids found. Phenylalanine(1.8% was the main aromatic amino acid , while tryptophane was completely absent.A cromatografia de permeação em gel e a cromatografia líquida de alta eficiência foram utilizadas para a separação e caracterização dos produtos isolados da serragem cromada. Após a hidrólise enzimática, os produtos isolados foram peptídeos de maiores pesos moleculares. Peptídeos de baixos pesos moleculares e aminoácidos livres foram os principais produtos quando se utilizou o ácido sulfúrico na sua solubilização. Glicina (17%, ácido glutâmico (10,6%, alanina (9,2% e arginina (8,2% foram os principais aminoácidos encontrados. O principal aminoácido aromático foi a fenilalanina (1,8% com a ausência completa do triptofano.

Microstructure and properties of high chrome steel roller after laser surface melting

International Nuclear Information System (INIS)

Li Meiyan; Wang Yong; Han Bin; Zhao Weimin; Han Tao

2009-01-01

Laser surface melting of high chrome steels was achieved by a 5 kW continuous wave CO 2 laser. The microstructure of the laser surface-melted steels was investigated by scanning electron microscopy, transmission electron microscopy and X-ray diffractometry, and the hardness profiles were determined by a Vickers hardness tester. The corrosion behavior in 3.5% NaCl solution was studied by electrochemical corrosion equipment. The large carbides of high chrome steels are completely dissolved and ultrafine dendrites of austenite with submicroscopic M 23 C 6 carbides precipitation are formed in the melted zone. The austenite in the melted zone has a high tempering stability. The corrosion resistance of the laser surface-melted steels is significantly improved due to the dissolution of carbides and the increase of the alloying elements in the solid solution as well as the large amount of austenite.

Characteristics of the chrome-tanned sheep leather treated by radiation-induced graft of BA

International Nuclear Information System (INIS)

Zhou Dezhong; Deng Yongzhen; Li Ying

1986-01-01

The characteristics of the chrome-tanned sheep leather treated by radiation-induced graft of BA is presented. Using the method of radiation-induced graft of BA instead of the chrome-retanning, the leather has been obviously improved not only in the surface, such as the brightness, fullness, uniformity of the thickness but also in the physical characteristics such as retaining of tensile strength, decreasing of water absorption after being immersed in water for 2h, and 24h, enhancement of tearing strength and stitch tear strength. Although the air permeability and water vapor permeability are a bit worse than the control, however is still in the range of the standard issued by Light Industry Ministry of China

Microstructure and properties of high chrome steel roller after laser surface melting

Energy Technology Data Exchange (ETDEWEB)

Li Meiyan, E-mail: lmy_102411@163.com [College of Electromechanical Engineering, China University of Petroleum, 271 Bei' er Road, Dongying 257061 (China); Wang Yong; Han Bin; Zhao Weimin; Han Tao [College of Electromechanical Engineering, China University of Petroleum, 271 Bei' er Road, Dongying 257061 (China)

2009-06-15

Laser surface melting of high chrome steels was achieved by a 5 kW continuous wave CO{sub 2} laser. The microstructure of the laser surface-melted steels was investigated by scanning electron microscopy, transmission electron microscopy and X-ray diffractometry, and the hardness profiles were determined by a Vickers hardness tester. The corrosion behavior in 3.5% NaCl solution was studied by electrochemical corrosion equipment. The large carbides of high chrome steels are completely dissolved and ultrafine dendrites of austenite with submicroscopic M{sub 23}C{sub 6} carbides precipitation are formed in the melted zone. The austenite in the melted zone has a high tempering stability. The corrosion resistance of the laser surface-melted steels is significantly improved due to the dissolution of carbides and the increase of the alloying elements in the solid solution as well as the large amount of austenite.

RESEARCH OF PROCESS OF AN ALLOYING OF THE FUSED COATINGS RECEIVED FROM THE SUPERFICIAL ALLOYED WIRE BY BORON WITH IN ADDITIONALLY APPLIED ELECTROPLATED COATING OF CHROME AND COPPER

Directory of Open Access Journals (Sweden)

V. A. Stefanovich

2015-01-01

Full Text Available Researches on distribution of chrome and copper in the fused coating received from the superficial alloyed wire by boron with in additionally applied electroplated coating of chrome and copper were executed. The structure of the fused coating consists of dendrites on which borders the boride eutectic is located. It is established that the content of chrome in dendrites is 1,5– 1,6 times less than in the borid; distribution of copper on structure is uniformed. Coefficients of digestion of chrome and copper at an argon-arc welding from a wire electrode with electroplated coating are established. The assimilation coefficient for chrome is equal to 0,9–1,0; for copper – 0,6–0,75.

Facile additive-free synthesis of iron oxide nanoparticles for efficient adsorptive removal of Congo red and Cr(VI)

Energy Technology Data Exchange (ETDEWEB)

Hao, Tao; Yang, Chao; Rao, Xuehui; Wang, Jide [Ministry Key Laboratory of Oil and Gas Fine Chemicals, College of Chemistry and Chemical Engineering, Xinjiang University, Urumqi 830046 (China); Niu, Chunge, E-mail: ncg@petrochina.com.cn [Petrochemical Research Institute, Karamay Petrochemical Company, Karamay 834000 (China); Su, Xintai, E-mail: suxintai827@163.com [Ministry Key Laboratory of Oil and Gas Fine Chemicals, College of Chemistry and Chemical Engineering, Xinjiang University, Urumqi 830046 (China)

2014-02-15

The iron oxide nanoparticles had been successfully synthesized via an additive-free hydrolysis process at 75 °C for 12 h. The product was characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), and N{sub 2} adsorption–desorption. The results of XRD and N{sub 2} adsorption–desorption demonstrated that the as-prepared product was mainly α-Fe{sub 2}O{sub 3} with a large surface area of 164.1 m{sup 2} g{sup −1}. The TEM images illustrated that the as-prepared product was found to consist of a mixture of irregular spherical nanoparticles (a diameter of ∼50 nm) and nanowhiskers (a diameter of ∼50 nm and uneven length). The as-prepared product was used to investigate its promising applications in water treatment. Due to its small size and large surface area, the maximum adsorption capacities of Congo red and Cr(VI) have been determined using the Langmuir equation and found to reach up to 253.8 and 17.0 mg g{sup −1}, respectively. The facile synthesis method and the superior adsorption performance derived from the iron oxide nanoparticles display the potential applications for the removal of Congo red and Cr(VI) from aqueous solution.

Occupational exposure to chrome VI compounds in French companies: results of a national campaign to measure exposure (2010-2013).

Science.gov (United States)

Vincent, Raymond; Gillet, Martine; Goutet, Pierre; Guichard, Christine; Hédouin-Langlet, Catherine; Frocaut, Anne Marie; Lambert, Pierre; Leray, Fabrice; Mardelle, Patricia; Dorotte, Michel; Rousset, Davy

2015-01-01

A campaign to measure exposure to hexavalent chromium compounds was carried out in France by the seven CARSAT chemistry laboratories, CRAMIF laboratory, and INRS over the 2010-2013 period. The survey included 99 companies involved in various activity sectors. The inhalable fraction of airborne particles was sampled, and exposure levels were determined using ion chromatography analysis combined with post-column derivatization and UV detection. The quality of the measurement results was guaranteed by an inter-laboratory comparison system involving all the laboratories participating in this study. Exposure levels frequently exceeded the French occupational exposure limit value (OELV) of 1 µg m(-3), in activities such as thermal metallization and manufacturing and application of paint in the aeronautics sector. The results also reveal a general trend for a greater proportion of soluble Chromium VI (Cr VI) compounds compared with insoluble compounds. Qualitative and quantitative information relating to the presence of other metallic compounds in the air of workplaces is also provided, for example for Cr III, Ni, Fe, etc. The sampling strategy used and the measurement method are easy to implement, making it possible to check occupational exposure with a view to comparing it to an 8 h-OELV of 1 µg m(-3). © The Author 2014. Published by Oxford University Press on behalf of the British Occupational Hygiene Society.

THE CONSEQUENCES ON BLOOD GSH DYNAMICS ON WISTAR FEMALE RATS AT AD LIBITUM CHROMIUM (VI ADMINISTRATION DURING THE GESTATION AFTER THE WEAN

Directory of Open Access Journals (Sweden)

CORINA GRĂVILĂ

2009-05-01

Full Text Available Chromium (VI is a widely used industrial chemical, extensively used in paints, metal finishes, steel including stainless steel manufacturing, alloy cast irons, chrome, and wood treatment. In nature chromium occurs in divalent, trivalent and hexavalent forms. Hexavalent chromium predominates over the trivalent form in natural waters. We have studied the influence of potassium dichromate (K2Cr2O7 on blood GSH values in rats. This study was carried out on 28 Wistar adult female rats, divided in 3 experimental groups (E and one control group (C. The rats were feed with 25ppm (LOAEL, 50ppm and 75ppm potassium dichromate, ad libitum, in drinking water, during the gestation. The control batch received tap water. Reduced glutathione (GSH was measured quantitatively after the wean using a Perkin-Elmer spectrophotometer, through Beutler et al. method, at 412nm. This study reports that potassium dichromate exposure induced the depletion of blood GSH because Cr(VI can generate reactive oxygen species (ROS. It can induce oxidative stress and toxicity.

Waste Treatment of Chrome Residue of Chromium Recovery Process Using Calcium Carbonate

International Nuclear Information System (INIS)

Endro Kismolo; Prayitno; Nurimaniwathy

2002-01-01

The aim of the research was to apply the precipitation technology for the treatment of aqueous wastes of leather tanning industries. The chrome liquid wastes taken was the effluent from the residue of the chromium recovery process using magnesium oxide. The precipitant used was calcium carbonate. The experiments was performed by adjusting the concentration of calcium carbonate from 50 ppm, 100 ppm, 150 ppm, 200 ppm, 250 ppm, 300 ppm, 350 ppm to 400 ppm. The stirring speed was varied from 50 rpm, 75 rpm, 100 rpm, 125 rpm, 150 rpm, 175 rpm to 200 rpm. The time of mixing was varied from 30 minutes, 60 minutes, 90 minutes, 120 minutes, 150 minutes, 175 minutes and 200 minutes. The result from the experiments lead to the best condition obtained were the concentration of precipitant was 300 ppm, flow rates of mixing was 125 rpm and time of mixing was 60 minutes. At this condition the separations efficiency of chrome obtained was 99.985%. (author)

Green chemistry approaches to leather tanning process for making chrome-free leather by unnatural amino acids.

Science.gov (United States)

Krishnamoorthy, G; Sadulla, S; Sehgal, P K; Mandal, Asit Baran

2012-05-15

In the present study, green and sustainable method or eco-friendly approaches to tanning process based on unnatural D-amino acids (D-AA)-aldehyde (Ald) as a substitute for chrome-free tanning has been attempted. The distribution of optically active D-AA in tanned leather, the hydrothermal stability, the mechanical properties and resistance to collagenolytic activity of tanned leather, the evaluation of eco-friendly characteristics were investigated. Scanning electron microscopic (SEM) and Atomic force microscopic (AFM) analyses indicate the surface morphology and roughness, respectively, of the tanned leather collagen matrix. Shrinkage and Differential scanning calorimetric (DSC) analyses shows that the shrinkage temperature (T(s)) and denaturation temperature (T(d)) of tanned leather are related to the content of D-AA+Ald present in the leather matrix. It has been found that the T(s) of D-AA tanned leather is more than that of Ald tanned leather and also more or less equal to chrome tanned leather. Environmental impact assessment (EIA) shows that the developed process results in significant reduction in total solids content (TSC) and improves better biodegradability of organic compound present in the effluent compared to chrome tanning. Copyright © 2012 Elsevier B.V. All rights reserved.

Identifying a novel role for X-prolyl aminopeptidase (Xpnpep) 2 in CrVI-induced adverse effects on germ cell nest breakdown and follicle development in rats.

Science.gov (United States)

Banu, Sakhila K; Stanley, Jone A; Sivakumar, Kirthiram K; Arosh, Joe A; Barhoumi, Rola; Burghardt, Robert C

2015-03-01

Environmental exposure to endocrine-disrupting chemicals (EDCs) is one cause of premature ovarian failure (POF). Hexavalent chromium (CrVI) is a heavy metal EDC widely used in more than 50 industries, including chrome plating, welding, wood processing, and tanneries. Recent data from U.S. Environmental Protection Agency indicate increased levels of Cr in drinking water from several American cities, which potentially predispose residents to various health problems. Recently, we demonstrated that gestational exposure to CrVI caused POF in F1 offspring. The current study was performed to identify the molecular mechanism behind CrVI-induced POF. Pregnant rats were treated with 25 ppm of potassium dichromate from Gestational Day (GD) 9.5 to GD 14.5 through drinking water, and the fetuses were exposed to CrVI through transplacental transfer. Ovaries were removed from the fetuses or pups on Embryonic Day (ED) 15.5, ED 17.5, Postnatal Day (PND) 1, PND 4, or PND 25, and various analyses were performed. Results showed that gestational exposure to CrVI: 1) increased germ cell/oocyte apoptosis and advanced germ cell nest (GCN) breakdown; 2) increased X-prolyl aminopeptidase (Xpnpep) 2, a POF marker in humans, during GCN breakdown; 3) decreased Xpnpep2 during postnatal follicle development; and 4) increased colocalization of Xpnpep2 with Col3 and Col4. We also found that Xpnpep2 inversely regulated the expression of Col1, Col3, and Col4 in all the developmental stages studied. Thus, CrVI advanced GCN breakdown and increased follicle atresia in F1 female progeny by targeting Xpnpep2. © 2015 by the Society for the Study of Reproduction, Inc.

PEEK-OPTIMA? as an alternative to cobalt chrome in the femoral component of total knee replacement: A preliminary study

OpenAIRE

Cowie, Raelene M; Briscoe, Adam; Fisher, John; Jennings, Louise M

2016-01-01

PEEK-OPTIMA™ (Invibio Ltd, UK) has been considered as an alternative joint arthroplasty bearing material due to its favourable mechanical properties and the biocompatibility of its wear debris. In this study, the potential to use injection moulded PEEK-OPTIMA™ as an alternative to cobalt chrome in the femoral component of a total knee replacement was investigated in terms of its wear performance. Experimental wear simulation of three cobalt chrome and three PEEK-OPTIMA™ femoral components art...

Effects of nanodiamonds of explosive synthesis on the skin of experimental animals locally exposed to cobalt and chrome ions.

Science.gov (United States)

Prokhorenkov, V I; Vasil'eva, E Yu; Puzyr', A P; Bondar', V S

2014-12-01

Experiments in vivo demonstrated the protective effect of modified nanodiamonds on guinea pig skin after local exposure cobalt ions, but not chrome ions. The observed differences are determined by different adsorption of these ions by nanodiamonds: in vitro experiments showed that nanodiamonds adsorbed cobalt ions, but not chrome ions from water solutions. The perspectives of using modified nanodiamonds as a new adsorbent for prevention of allergic contact dermatitis induced by ions of bivalent metals are discussed.

Minimization of the environmental impact of chrome tanning: a new process with high chrome exhaustion.

Science.gov (United States)

Morera, Josep M; Bacardit, Anna; Ollé, Lluís; Bartolí, Esther; Borràs, Maria D

2007-11-01

In all tanning technology operations wastes are generated. These reach the environment as residual waters, solid and liquid waste as well as atmospheric emissions and odours. This study tests an alternative method to the traditional tanning method at an industrial level. The new method is based on tanning without float and by significantly increasing the temperature at the end of the tanning process. The properties of the leathers obtained using the two methods have been compared and the results indicate that those leathers have similar physical, chemical, and organoleptic properties. However, the differences existing from the environmental point of view are significant. It is not necessary to use clean water for this tanning. Moreover, there is a 75% reduction of the residual float, a 91% reduction of the chrome discharged, and a 94% reduction of the chlorides discharged. A financial assessment was carried out to demonstrate that the newly proposed system is 32% more economic than the traditional one.

Radiation-initiated graft polymerization of methyl acrylate onto chrome-tanned sheepskin

International Nuclear Information System (INIS)

Kaldirimci, C.; Bas, N.

1982-01-01

Radiation grafting method was applied to obtain leather-polymer composite. Grafting of methyl acrylate onto chrome-tanned, bluestock sheepskin was investigated under the initiatory effect of 60 Co radiation of 0.20 11.50 Mrad. The percent of grafting was determined and water adsorption and shrinkage temperature measurements were carried out. It was shown that 2-4 Mrad is convenient to produce leather-polymer composite. (author)

Synthesis of surface Cr (VI)-imprinted magnetic nanoparticles for selective dispersive solid-phase extraction and determination of Cr (VI) in water samples.

Science.gov (United States)

Qi, Xue; Gao, Shuang; Ding, Guosheng; Tang, An-Na

2017-01-01

A facile, rapid and selective magnetic dispersed solid-phase extraction (dSPE) method for the extraction and enrichment of Cr (VI) prior to flame atomic absorption spectrometry (AAS) was introduced. For highly selective and efficient extraction, magnetic Cr (VI)-imprinted nanoparticles (Fe 3 O 4 @ Cr (VI) IIPs) were prepared by hyphenating surface ion-imprinted with sol-gel techniques. In the preparation process, chromate (Cr(VI)) was used as the template ion; vinylimidazole and 3-aminopropyltriethoxysilane were selected as organic functional monomer and co-monomer respectively. Another reagent, methacryloxypropyltrimethoxysilane was adopted as coupling agent to form the stable covalent bonding between organic and inorganic phases. The effects of various parameters on the extraction efficiency, such as pH of sample solution, the amount of adsorbent, extraction time, the type and concentration of eluent were systematically investigated. Furthermore, the thermodynamic and kinetic properties of the adsorption process were studied to explore the internal adsorption mechanism. Under optimized conditions, the preconcentration factor, limit of detection and linear range of the established dSPE-AAS method for Cr (VI) were found to be 98, 0.29μgL -1 and 4-140μgL -1 , respectively. The developed method was also successfully applied to the analysis of Cr (VI) in different water samples with satisfactory results, proving its reliability and feasibility in real sample analysis. Copyright © 2016 Elsevier B.V. All rights reserved.

Application of Nuclear methods in the chrome bed prospecting from Casimba sector, Pinares de Mayari

International Nuclear Information System (INIS)

Guerra, M.; Velazquez Cruz, R.

1993-01-01

A study for chrome determination in Casimba sector, Pinares de Mayari, was carried out using nuclear geophysical methods: and spectrometry neutron-gamma capture. For this purpose Cs 137 and Am-Be sources were used

40 CFR 425.20 - Applicability; description of the hair save, chrome tan, retan-wet finish subcategory.

Science.gov (United States)

2010-07-01

... ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS LEATHER TANNING AND FINISHING... cattle-like hides into finished leather by hair save unhairing, chrome tanning, and retan-wet finishing. ...

Spectroscopic confirmation of uranium(VI)-carbonato adsorption complexes on hematite

Science.gov (United States)

Bargar, John R.; Reitmeyer, Rebecca; Davis, James A.

1999-01-01

Evaluating societal risks posed by uranium contamination from waste management facilities, mining sites, and heavy industry requires knowledge about uranium transport in groundwater, often the most significant pathway of exposure to humans. It has been proposed that uranium mobility in aquifers may be controlled by adsorption of U(VI)−carbonato complexes on oxide minerals. The existence of such complexes has not been demonstrated, and little is known about their compositions and reaction stoichiometries. We have used attenuated total reflectance Fourier transform infrared (ATR-FTIR) and extended X-ray absorption fine structure (EXAFS) spectroscopies to probe the existence, structures, and compositions of ≡FeOsurface−U(VI)−carbonato complexes on hematite throughout the pH range of uranyl uptake under conditions relevant to aquifers. U(VI)−carbonato complexes were found to be the predominant adsorbed U(VI) species at all pH values examined, a much wider pH range than previously postulated based on analogy to aqueous U(VI)−carbonato complexes, which are trace constituents at pH carbonato complexes may be of major importance to the groundwater transport of similar actinide contaminants such as neptunium and plutonium.

Enhanced Cr(VI) removal by polyethylenimine- and phosphorus-codoped hierarchical porous carbons.

Science.gov (United States)

Chen, Shixia; Wang, Jun; Wu, Zeliang; Deng, Qiang; Tu, Wenfeng; Dai, Guiping; Zeng, Zheling; Deng, Shuguang

2018-08-01

The amino- and phosphorus-codoped (N,P-codoped) porous carbons derived from oil-tea shells were facilely fabricated through a combination of phosphoric acid (H 3 PO 4 ) activation and amino (polyethylenimine, PEI) modification method. The as-synthesized carbon adsorbents were systematically characterized and evaluated for Cr(VI) removal in aqueous solutions. The relationship between adsorbent properties and adsorption behaviors was illustrated. Moreover, the influences of contact time, initial Cr(VI) concentration, pH, coexisting anions and temperature were also investigated. The adsorption behavior of Cr(VI) could be perfectly described by the pseudo-second-order kinetic model and Sips adsorption model. The maximum adsorption capacity of Cr(VI) on the carbon adsorbents synthesized in this work was 355.0 mg/g, and this excellent Cr(VI) capacity could be sustained with other coexisting anions. In addition to high surface area and suitable pore size distribution, the high Cr(VI) removal capacity is induced by rich heteroatoms incorporation and the Cr(VI) removal mechanism was clearly illustrated. Furthermore, the continuous column breakthrough experiment on obtained N,P-codoped carbon was conducted and well fitted by the Thomas model. This work revealed that PEI modification and P-containing groups could significantly enhance Cr(VI) adsorption capacity and make these N,P-codoped biomass-derived carbons potent adsorbents in practical water treatment applications. Copyright © 2018 Elsevier Inc. All rights reserved.

Environmentally Friendly Zirconium Oxide Pretreatment

Science.gov (United States)

2013-05-01

Society for Testing and Materials AVCRAD Aviation Classification Repair Activity Depot Chrome (VI) Hexavalent Chromium CRS Cold Rolled Steel...are being used commercially in automotive and other industrial operations as replacements to hexavalent chromium-based and zinc phosphate...application over CRS and aluminum with water-borne and solvent-borne Mil-Spec primers gave results in corrosion performance similar to the chrome

Comparative statistical analysis of chrome and vegetable tanning effluents and their effects on related soil

International Nuclear Information System (INIS)

Tariq, Saadia R.; Shah, Munir H.; Shaheen, Nazia

2009-01-01

Two tanning units of Pakistan, namely, Kasur and Mian Channun were investigated with respect to the tanning processes (chrome and vegetable, respectively) and the effects of the tanning agents on the quality of soil in vicinity of tanneries were evaluated. The effluent and soil samples from 16 tanneries each of Kasur and Mian Channun were collected. The levels of selected metals (Na, K, Ca, Mg, Fe, Cr, Mn, Co, Cd, Ni, Pb and Zn) were determined by using flame atomic absorption spectrophotometer under optimum analytical conditions. The data thus obtained were subjected to univariate and multivariate statistical analyses. Most of the metals exhibited considerably higher concentrations in the effluents and soils of Kasur compared with those of Mian Channun. It was observed that the soil of Kasur was highly contaminated by Na, K, Ca and Mg emanating from various processes of leather manufacture. Furthermore, the levels of Cr were also present at much enhanced levels than its background concentration due to the adoption of chrome tanning. The levels of Cr determined in soil samples collected from the vicinity of Mian Channun tanneries were almost comparable to the background levels. The soil of this city was found to have contaminated only by the metals originating from pre-tanning processes. The apportionment of selected metals in the effluent and soil samples was determined by a multivariate cluster analysis, which revealed significant differences in chrome and vegetable tanning processes.

Comparative statistical analysis of chrome and vegetable tanning effluents and their effects on related soil.

Science.gov (United States)

Tariq, Saadia R; Shah, Munir H; Shaheen, Nazia

2009-09-30

Two tanning units of Pakistan, namely, Kasur and Mian Channun were investigated with respect to the tanning processes (chrome and vegetable, respectively) and the effects of the tanning agents on the quality of soil in vicinity of tanneries were evaluated. The effluent and soil samples from 16 tanneries each of Kasur and Mian Channun were collected. The levels of selected metals (Na, K, Ca, Mg, Fe, Cr, Mn, Co, Cd, Ni, Pb and Zn) were determined by using flame atomic absorption spectrophotometer under optimum analytical conditions. The data thus obtained were subjected to univariate and multivariate statistical analyses. Most of the metals exhibited considerably higher concentrations in the effluents and soils of Kasur compared with those of Mian Channun. It was observed that the soil of Kasur was highly contaminated by Na, K, Ca and Mg emanating from various processes of leather manufacture. Furthermore, the levels of Cr were also present at much enhanced levels than its background concentration due to the adoption of chrome tanning. The levels of Cr determined in soil samples collected from the vicinity of Mian Channun tanneries were almost comparable to the background levels. The soil of this city was found to have contaminated only by the metals originating from pre-tanning processes. The apportionment of selected metals in the effluent and soil samples was determined by a multivariate cluster analysis, which revealed significant differences in chrome and vegetable tanning processes.

Comparative statistical analysis of chrome and vegetable tanning effluents and their effects on related soil

Energy Technology Data Exchange (ETDEWEB)

Tariq, Saadia R. [Department of Chemistry, Lahore College for Women University, Lahore (Pakistan); Shah, Munir H., E-mail: munir_qau@yahoo.com [Department of Chemistry, Quaid-i-Azam University, Islamabad 45320 (Pakistan); Shaheen, Nazia [Department of Chemistry, Quaid-i-Azam University, Islamabad 45320 (Pakistan)

2009-09-30

Two tanning units of Pakistan, namely, Kasur and Mian Channun were investigated with respect to the tanning processes (chrome and vegetable, respectively) and the effects of the tanning agents on the quality of soil in vicinity of tanneries were evaluated. The effluent and soil samples from 16 tanneries each of Kasur and Mian Channun were collected. The levels of selected metals (Na, K, Ca, Mg, Fe, Cr, Mn, Co, Cd, Ni, Pb and Zn) were determined by using flame atomic absorption spectrophotometer under optimum analytical conditions. The data thus obtained were subjected to univariate and multivariate statistical analyses. Most of the metals exhibited considerably higher concentrations in the effluents and soils of Kasur compared with those of Mian Channun. It was observed that the soil of Kasur was highly contaminated by Na, K, Ca and Mg emanating from various processes of leather manufacture. Furthermore, the levels of Cr were also present at much enhanced levels than its background concentration due to the adoption of chrome tanning. The levels of Cr determined in soil samples collected from the vicinity of Mian Channun tanneries were almost comparable to the background levels. The soil of this city was found to have contaminated only by the metals originating from pre-tanning processes. The apportionment of selected metals in the effluent and soil samples was determined by a multivariate cluster analysis, which revealed significant differences in chrome and vegetable tanning processes.

Radiation induced graft copolymerization of methyl methacrylate onto chrome-tanned pig skins

International Nuclear Information System (INIS)

Pietrucha, K.; Pekala, W.; Kroh, J.

1981-01-01

Graft copolymerization of methyl methacrylate (MMA) onto chrome-tanned pig skins was carried out by irradiation with 60 Co γ-rays. The grafted polymethyl methacrylate (PMMA) chains were isolated by acid hydrolysis of the collagen backbone in order to characterize the graft copolymers. Proof of grafting was obtained through the detection of amino acid endgroups in the isolated grafts by reaction with ninhydrin. The grafting yield of MMA in aqueous emulsion was found to be higher than that for pure MMA and MMA in acetone. The degree of grafting increases with increasing monomer concentration in emulsion and reaches maximum at radiation dose ca 15 kGy. The yield of grafting is very high. The present paper reports the physical properties of chrome-tanned pig skins after graft polymerization with MMA in emulsion. Modified leathers are more resistant against water absorption and abrasion in comparison with unmodified ones. They have more uniform structure over the whole surface, greater thickness and stiffness. The mechanism of some of the processes occurring during radiation grafting of MMA in water emulsion on tanned leathers has been also suggested and discussed. (author)

Radiation induced graft copolymerization of methyl methacrylate onto chrome-tanned pig skins

Energy Technology Data Exchange (ETDEWEB)

Pietrucha, K.; Pekala, W.; Kroh, J. (Lodz Univ. (Poland))

1981-01-01

Graft copolymerization of methyl methacrylate (MMA) onto chrome-tanned pig skins was carried out by irradiation with /sup 60/Co ..gamma..-rays. The grafted polymethyl methacrylate (PMMA) chains were isolated by acid hydrolysis of the collagen backbone in order to characterize the graft copolymers. Proof of grafting was obtained through the detection of amino acid endgroups in the isolated grafts by reaction with ninhydrin. The grafting yield of MMA in aqueous emulsion was found to be higher than that for pure MMA and MMA in acetone. The degree of grafting increases with increasing monomer concentration in emulsion and reaches maximum at radiation dose ca 15 kGy. The yield of grafting is very high. The present paper reports the physical properties of chrome-tanned pig skins after graft polymerization with MMA in emulsion. Modified leathers are more resistant against water absorption and abrasion in comparison with unmodified ones. They have more uniform structure over the whole surface, greater thickness and stiffness. The mechanism of some of the processes occurring during radiation grafting of MMA in water emulsion on tanned leathers has been also suggested and discussed.

Compliance with the Clean Air Act Title VI Stratospheric Ozone Protection Program requirements at U.S. DOE Oak Ridge Reservation Facilities

International Nuclear Information System (INIS)

Humphreys, M.P.; Atkins, E.M.

1999-01-01

The Title VI Stratospheric Ozone Protection Program of the Clean Air Act (CAA) requires promulgation of regulations to reduce and prevent damage to the earth's protective ozone layer. Regulations pursuant to Title VI of the CAA are promulgated in the Code of Federal Regulations (CFR) at Title 40 CFR, Part 822. The regulations include ambitious production phaseout schedules for ozone depleting substances (ODS) including chlorofluorocarbons (CFCs), hydrochlorofluorocarbons (HCFCs), halons, carbon tetrachloride, and methyl chloroform under 40 CFR 82, Subpart A. The regulations also include requirements for recycling and emissions reduction during the servicing of refrigeration equipment and technician certification requirements under Subpart F; provisions for servicing of motor vehicle air conditioners under Subpart B; a ban on nonessential products containing Class 1 ODS under Subpart C; restrictions on Federal procurement of ODS under Subpart D; labeling of products using ODS under Subpart E; and the Significant New Alternatives Policy Program under Subpart G. This paper will provide details of initiatives undertaken at US Department of Energy (DOE) Oak Ridge Reservation (ORR) Facilities for implementation of requirements under the Title VI Stratospheric Ozone Protection Program. The Stratospheric Ozone Protection Plans include internal DOE requirements for: (1) maintenance of ODS inventories; (2) ODS procurement practices; (3) servicing of refrigeration and air conditioning equipment; (4) required equipment modifications or replacement; (5) technician certification training; (6) labeling of products containing ODS; (7) substitution of chlorinated solvents; and (8) replacement of halon fire protection systems. The plans also require establishment of administrative control systems which assure that compliance is achieved and maintained as the regulations continue to develop and become effective

Surface enrichment with chrome and nitriding of IF steel under an abnormal glow discharge

International Nuclear Information System (INIS)

Meira, S.R.; Borges, P.C.; Bernardelli, E.A.

2014-01-01

The objective of this work is to evaluate the influence of surface enrichment of IF steel with chrome, and nitriding, the formation of the nitrided layer. Thus, IF steel samples were subjected to surface enrichment process, using 409 stainless steel as a target for sputtering, followed by plasma nitriding, both under a dc abnormal glow discharge. The enrichment treatment was operated at 1200 ° C for 3h. The nitriding treatment was operated at 510 ° C for 2 h. The influence of the treatments on the layers formed was studied through optical microscopy (OM), scan electron microscopy (SEM), X-ray diffraction (XRD) and Vickers microindentation. The results show that the enrichment is effective to enrich the IF surface, furthermore, improves the characteristics of nitriding, comparing nitriding samples to nitriding and enriched, was observed needles of nitrides, as well as a higher hardness, which is associated with the nitrides of chrome, on the nitriding and enriched samples. (author)

Nucleotide sequence of Hungarian grapevine chrome mosaic nepovirus RNA1.

OpenAIRE

Le Gall, O; Candresse, T; Brault, V; Dunez, J

1989-01-01

The nucleotide sequence of the RNA1 of hungarian grapevine chrome mosaic virus, a nepovirus very closely related to tomato black ring virus, has been determined from cDNA clones. It is 7212 nucleotides in length excluding the 3' terminal poly(A) tail and contains a large open reading frame extending from nucleotides 216 to 6971. The presumably encoded polyprotein is 2252 amino acids in length with a molecular weight of 250 kDa. The primary structure of the polyprotein was compared with that o...

Separation of motor oils, oily wastes and hydrocarbons from contaminated water by sorption on chrome shavings.

Science.gov (United States)

Gammoun, A; Tahiri, S; Albizane, A; Azzi, M; Moros, J; Garrigues, S; de la Guardia, M

2007-06-25

In this paper, the ability of chrome shavings to remove motor oils, oily wastes and hydrocarbons from water has been studied. To determine amount of hydrocarbons sorbed on tanned wastes, a FT-NIR methodology was used and a multivariate calibration based on partial least squares (PLS) was employed for data treatment. The light density, porous tanned waste granules float on the surface of water and remove hydrocarbons and oil films. Wastes fibers from tannery industry have high sorption capacity. These tanned solid wastes are capable of absorbing many times their weight in oil or hydrocarbons (6.5-7.6g of oil and 6.3g of hydrocarbons per gram of chrome shavings). The removal efficiency of the pollutants from water is complete. The sorption of pollutants is a quasi-instantaneous process.

CHROME: An Approach to Teaching the Concept of Inter-Functional Cooperation in Services Organizations

Science.gov (United States)

Johnson, Lester W.

2010-01-01

When teaching a services course (e.g., Services Marketing) it is essential that students understand that marketing/management, operations and human resource management within the service organization be fully coordinated. One useful acronym used to remind students of this need is "CHROME", standing for Communications, Human Resources,…

A useful single-solution polychrome stain for plant material...Brook Cyte-Chrome I.

Science.gov (United States)

Stanley L Krugman; Julia F. Littlefield

1968-01-01

Fresh and chemically fixed sectioned plant material can be quickly stained by applying a Brook Cyte Chrome I polychrome stain. Staining time averaged only about 10 minutes. And exact timing of staining and de-staining is not as critical as with most of the commonly used stains. The overall quality is comparable to that of the traditional stains.

[New perspectives in biomonitoring of metallic elements: the example of hexavalent chromium].

Science.gov (United States)

Mutti, A; De Palma, G; Goldoni, M

2012-01-01

Plating industry is an important productive sector in all the national territory, because of its contribution to a high number of industrial products and crafts. In the chrome plating sector there is a specific chemical risk due to the exposure to compounds containing hexavalent Chromium [Cr(VI)]. Exhaled breath condensate (EBC) has been used to study both acute and long term exposure to Cr(VI) in chrome plating workers. Cr-EBC correlates with specific oxidative stress biomarkers. Moreover, both total Cr and its hexavalent fraction can be measured in EBC, which therefore is a promising biological fluid to assess the absorbed dose at the target organ level, the pulmonary reduction kinetics of Cr(VI) and in general its local pneumotoxic effects. EBC collection and analysis could give additional information to the traditional measures performed during biomonitoring.

Chromium Elimination and Cannon Life Extension for Gun Tubes

Science.gov (United States)

2012-08-30

the use of hexavalent chromium (VI) in the production of cannon barrels by developing a cost effective environmentally friendly Explosive Bonding...erosion- resistant chrome cobalt alloy matrix with 15% tungsten. Stellite is used as M60 machine gun barrel liner. Tantalum Cobalt Tungsten...Grounds (YPG) Preliminary proof of principle endurance testing at YPG shows promising results when conducted side by side to a chrome plated

PEEK-OPTIMA™ as an alternative to cobalt chrome in the femoral component of total knee replacement: A preliminary study.

Science.gov (United States)

Cowie, Raelene M; Briscoe, Adam; Fisher, John; Jennings, Louise M

2016-11-01

PEEK-OPTIMA ™ (Invibio Ltd, UK) has been considered as an alternative joint arthroplasty bearing material due to its favourable mechanical properties and the biocompatibility of its wear debris. In this study, the potential to use injection moulded PEEK-OPTIMA ™ as an alternative to cobalt chrome in the femoral component of a total knee replacement was investigated in terms of its wear performance. Experimental wear simulation of three cobalt chrome and three PEEK-OPTIMA ™ femoral components articulating against all-polyethylene tibial components was carried out under two kinematic conditions: 3 million cycles under intermediate kinematics (maximum anterior-posterior displacement of 5 mm) followed by 3 million cycles under high kinematic conditions (anterior-posterior displacement 10 mm). The wear of the GUR1020 ultra-high-molecular-weight polyethylene tibial components was assessed by gravimetric analysis; for both material combinations under each kinematic condition, the mean wear rates were low, that is, below 5 mm 3 /million cycles. Specifically, under intermediate kinematic conditions, the wear rate of the ultra-high-molecular-weight polyethylene tibial components was 0.96 ± 2.26 mm 3 /million cycles and 2.44 ± 0.78 mm 3 /million cycle against cobalt chrome and PEEK-OPTIMA ™ implants, respectively (p = 0.06); under high kinematic conditions, the wear rates were 2.23 ± 1.85 mm 3 /million cycles and 4.44 ± 2.35 mm 3 /million cycles, respectively (p = 0.03). Following wear simulation, scratches were apparent on the surface of the PEEK-OPTIMA ™ femoral components. The surface topography of the femoral components was assessed using contacting profilometry and showed a statistically significant increase in measured surface roughness of the PEEK-OPTIMA ™ femoral components compared to the cobalt chrome implants. However, this did not appear to influence the wear rate, which remained linear over the duration of

PEEK-OPTIMA™ as an alternative to cobalt chrome in the femoral component of total knee replacement: A preliminary study

Science.gov (United States)

Cowie, Raelene M; Briscoe, Adam; Fisher, John; Jennings, Louise M

2016-01-01

PEEK-OPTIMA™ (Invibio Ltd, UK) has been considered as an alternative joint arthroplasty bearing material due to its favourable mechanical properties and the biocompatibility of its wear debris. In this study, the potential to use injection moulded PEEK-OPTIMA™ as an alternative to cobalt chrome in the femoral component of a total knee replacement was investigated in terms of its wear performance. Experimental wear simulation of three cobalt chrome and three PEEK-OPTIMA™ femoral components articulating against all-polyethylene tibial components was carried out under two kinematic conditions: 3 million cycles under intermediate kinematics (maximum anterior-posterior displacement of 5 mm) followed by 3 million cycles under high kinematic conditions (anterior-posterior displacement 10 mm). The wear of the GUR1020 ultra-high-molecular-weight polyethylene tibial components was assessed by gravimetric analysis; for both material combinations under each kinematic condition, the mean wear rates were low, that is, below 5 mm3/million cycles. Specifically, under intermediate kinematic conditions, the wear rate of the ultra-high-molecular-weight polyethylene tibial components was 0.96 ± 2.26 mm3/million cycles and 2.44 ± 0.78 mm3/million cycle against cobalt chrome and PEEK-OPTIMA™ implants, respectively (p = 0.06); under high kinematic conditions, the wear rates were 2.23 ± 1.85 mm3/million cycles and 4.44 ± 2.35 mm3/million cycles, respectively (p = 0.03). Following wear simulation, scratches were apparent on the surface of the PEEK-OPTIMA™ femoral components. The surface topography of the femoral components was assessed using contacting profilometry and showed a statistically significant increase in measured surface roughness of the PEEK-OPTIMA™ femoral components compared to the cobalt chrome implants. However, this did not appear to influence the wear rate, which remained linear over the duration of the study. These

Influences of the current density on the performances of the chrome-plated layer in deterministic electroplating repair

Science.gov (United States)

Xia, H.; Shen, X. M.; Yang, X. C.; Xiong, Y.; Jiang, G. L.

2018-01-01

Deterministic electroplating repair is a novel method for rapidly repairing the attrited parts. By the qualitative contrast and quantitative comparison, influences of the current density on performances of the chrome-plated layer were concluded in this study. The chrome-plated layers were fabricated under different current densities when the other parameters were kept constant. Hardnesses, thicknesses and components, surface morphologies and roughnesses, and wearability of the chrome-plated layers were detected by the Vickers hardness tester, scanning electron microscope / energy dispersive X-ray detector, digital microscope in the 3D imaging mode, and the ball-milling instrument with profilograph, respectively. In order to scientifically evaluate each factor, the experimental data was normalized. A comprehensive evaluation model was founded to quantitative analyse influence of the current density based on analytic hierarchy process method and the weighted evaluation method. The calculated comprehensive evaluation indexes corresponding to current density of 40A/dm2, 45A/dm2, 50A/dm2, 55A/dm2, 60A/dm2, and 65A/dm2 were 0.2246, 0.4850, 0.4799, 0.4922, 0.8672, and 0.1381, respectively. Experimental results indicate that final optimal option was 60A/dm2, and the priority orders were 60A/dm2, 55A/dm2, 45A/dm2, 50A/dm2, 40A/dm2, and 65A/dm2.

Facile synthesis of reduced graphene oxide/peroxomolybdate(VI)-citrate composite and its potential energy storage application

Energy Technology Data Exchange (ETDEWEB)

Ciszewski, Mateusz; Benke, Grzegorz; Leszczynska-Sejda, Katarzyna; Kopyto, Dorota [Institute of Non Ferrous Metals, Department of Hydrometallurgy, Gliwice (Poland)

2017-11-15

A new energy storage material based on molybdate active species has been presented. Molybdenum seems to be a perspective material in supercapacitors because of numerous possible metal oxidation states, electrolyte storage by means of various chemical reactions and availability in comparison to other refractory metals. Material synthesized within this research was composed of reduced graphene oxide matrix and peroxomolybdate(VI)-citrate active dimers. It was showed that peroxomolybdate(VI)-citrate structure enhanced electrochemical activity of symmetric supercapacitor. Simple methodology was used to synthesize a composite with pH adjustment as the key step. The specific capacity calculated from galvanostatic charge/discharge curves was as high as 250 F/g. Material was distinguished by good cyclability with 5% capacity loss after 1000 cycles. The increase in charge transfer resistance, induced by metal-oxygen compound within the carbon matrix was relatively low, compared to parent reduced graphene oxide. Amorphous structure of peroxomolybdate(VI)-modified material was observed with slight increase in the interlayer distance in comparison to parent reduced graphene oxide. The height and lateral size of crystallites were also determined. Significant decrease in the specific surface area of peroxomolybdate(VI)-modified composite was observed, in comparison to the parent reduced graphene oxide. (orig.)

Facile synthesis of reduced graphene oxide/peroxomolybdate(VI)-citrate composite and its potential energy storage application

International Nuclear Information System (INIS)

Ciszewski, Mateusz; Benke, Grzegorz; Leszczynska-Sejda, Katarzyna; Kopyto, Dorota

2017-01-01

A new energy storage material based on molybdate active species has been presented. Molybdenum seems to be a perspective material in supercapacitors because of numerous possible metal oxidation states, electrolyte storage by means of various chemical reactions and availability in comparison to other refractory metals. Material synthesized within this research was composed of reduced graphene oxide matrix and peroxomolybdate(VI)-citrate active dimers. It was showed that peroxomolybdate(VI)-citrate structure enhanced electrochemical activity of symmetric supercapacitor. Simple methodology was used to synthesize a composite with pH adjustment as the key step. The specific capacity calculated from galvanostatic charge/discharge curves was as high as 250 F/g. Material was distinguished by good cyclability with 5% capacity loss after 1000 cycles. The increase in charge transfer resistance, induced by metal-oxygen compound within the carbon matrix was relatively low, compared to parent reduced graphene oxide. Amorphous structure of peroxomolybdate(VI)-modified material was observed with slight increase in the interlayer distance in comparison to parent reduced graphene oxide. The height and lateral size of crystallites were also determined. Significant decrease in the specific surface area of peroxomolybdate(VI)-modified composite was observed, in comparison to the parent reduced graphene oxide. (orig.)

Spectroscopic Confirmation of Uranium (VI)-Carbonato Adsorption Complexes on Hematite

International Nuclear Information System (INIS)

Bargar, John R

1999-01-01

Evaluating societal risks posed by uranium contamination from waste management facilities, mining sites, and heavy industry requires knowledge about uranium transport in groundwater, often the most significant pathway of exposure to humans. It has been proposed that uranium mobility in aquifers may be controlled by adsorption of U(VI)-carbonato complexes on oxide minerals. The existence of such complexes has not been demonstrated, and little is known about their compositions and reaction stoichiometries. We have used Attenuated Total Reflectance Fourier Transform Infrared (ATR-FTIR) and Extended X-ray Absorption Fine Structure (EXAFS) spectroscopies to probe the existence, structures, and compositions of FeO surface -U(VI)-carbonato complexes on hematite throughout the pH range of uranyl uptake under conditions relevant to aquifers. U(VI)-carbonato complexes were found to be the predominant adsorbed U(VI) species at all pH values examined, a much wider pH range than previously postulated based on analogy to aqueous U(VI)-carbonato complexes, which are trace constituents at pH < 6. This result indicates the inadequacy of the common modeling assumption that the compositions and predominance of adsorbed species can be inferred from aqueous species. By extension, adsorbed carbonato complexes may be of major importance to the groundwater transport of similar actinide contaminants such as neptunium and plutonium

An electrochemical study of U(VI) and Cr(VI) in molten borates

International Nuclear Information System (INIS)

Brigaudeau, M.; Gregori de Pinochet, I. de

1977-01-01

The electrochemical reduction of U(VI) and Cr(VI), in molten Na 2 B 4 O 7 at 800 deg C was studied by means of linear sweep voltammetry, and chronopotentiometry. The reduction of U(VI) to U(V) proceeded reversibly at a platinum electrode. The diffusion coefficient for the U(VI) species at 800 deg C was 4.10 -7 cm 2 .s -1 . The activation energy of diffusion was (34,8 +- 0,8) kcal. mole -1 . Electrochemical studies of Cr(VI) at 800 0 C reveal a two-step reduction process at a platinum electrode. Only the voltammogram for the first step charge transfer process was studied. Analysis indicated that Cr(VI) is reversibly reduced to Cr(III) at a platinum electrode. The diffusion coefficient for Cr(VI) at 800 0 C is 1,9.10 -7 cm 2 .s -1 [fr

Spectrophotometric determination of Sc in eriochrome cyanine R(chrome azurol S) - phosphatidyl choline system

International Nuclear Information System (INIS)

Xu, Y.; Chen, X.; Hu, Z.

1987-01-01

Eriochrome cyanine R(chrome azurol S) is used as a color reagent to determine Sc in the presence of phosphatidyl choline, eta = 3.7 * 10 4 (4.5 * 10 4 ). This method has been connected to extraction separation to determine Sc in the presence of rare earth elements, and good results have been obtained. Phosphatidyl choline(PC) is a biochemical reagent, which can be used as a surfactant. It has been reported that chrome azurol S(CAS) can be used to determine Be in the presence of PC but it has not been reported that eriochrome cyanine R(ECR) and CAS can been used to determine Sc in the presence of PC. This paper has put forward a method by which Sc can be determined. ECR (CAS) has been used as a color reagent and PC as a surfactant. Conditional experiments have been made and this method has been connected to extraction separation. Tributyl phosphate (TBP) extracts Sc from rare earth elements to make a determination and good results have been obtained

Remediation of Cr(VI) contaminated soil using long-duration sodium thiosulfate supported by micro–nano networks

International Nuclear Information System (INIS)

He, Lulu; Wang, Min; Zhang, Guilong; Qiu, Guannan; Cai, Dongqing; Wu, Zhengyan; Zhang, Xin

2015-01-01

Highlights: • This work aims to develop a long-duration remediation agent (LRA). • LRA was obtained using Na 2 S 2 O 3 supported by attapulgite (ATP) micro–nano networks. • ATP micro–nano networks was induced by high-energy electron beam irradiation. • LRA can effectively control the migration of Cr(VI) and reducing Cr(VI) to Cr(III). • LRA displayed high performance on the remediation of heavy metal contaminated soil. - Abstract: In this work, a long-duration remediation agent (LRA) on hexavalent chromium (Cr(VI)) was developed using sodium thiosulfate (ST) supported by attapulgite (ATP) micro–nano networks induced through high-energy electron beam (HEEB) irradiation. The ATP networks could effectively reduce the leaching amount of Cr(VI) in soil. More importantly, the ATP networks could significantly control the leaching behavior of ST, and then prolong the duration and increase the reduction efficiency of ST on Cr(VI). As a result, LRA displayed high performance on controlling the migration of Cr(VI) and reducing Cr(VI) to Cr(III). Additionally, pot experiment indicated that LRA could effectively decrease the absorbed amount of Cr(VI) in corn, and reduce the inhibition effect of Cr(VI) on the growth of corn. Therefore, this work could provide a facile approach to remediate the Cr(VI)-contaminated soil and lower the harmful effect of Cr(VI) on crop

Remediation of Cr(VI) contaminated soil using long-duration sodium thiosulfate supported by micro–nano networks

Energy Technology Data Exchange (ETDEWEB)

He, Lulu [School of Life Sciences, Anhui Agricultural University, Hefei 230036 (China); Key Laboratory of Ion Beam Bioengineering, Hefei Institutes of Physical Science, Chinese Academy of Sciences and Anhui Province, Hefei, Anhui 230031 (China); Wang, Min; Zhang, Guilong [Key Laboratory of Ion Beam Bioengineering, Hefei Institutes of Physical Science, Chinese Academy of Sciences and Anhui Province, Hefei, Anhui 230031 (China); Bioenergy Forest Research Center of State Forestry Administration, Hefei 230031 (China); Qiu, Guannan [Key Laboratory of Ion Beam Bioengineering, Hefei Institutes of Physical Science, Chinese Academy of Sciences and Anhui Province, Hefei, Anhui 230031 (China); Cai, Dongqing, E-mail: dqcai@ipp.ac.cn [Key Laboratory of Ion Beam Bioengineering, Hefei Institutes of Physical Science, Chinese Academy of Sciences and Anhui Province, Hefei, Anhui 230031 (China); Bioenergy Forest Research Center of State Forestry Administration, Hefei 230031 (China); Wu, Zhengyan, E-mail: zywu@ipp.ac.cn [Key Laboratory of Ion Beam Bioengineering, Hefei Institutes of Physical Science, Chinese Academy of Sciences and Anhui Province, Hefei, Anhui 230031 (China); Bioenergy Forest Research Center of State Forestry Administration, Hefei 230031 (China); Zhang, Xin, E-mail: xinzhang@ahau.edu.cn [School of Life Sciences, Anhui Agricultural University, Hefei 230036 (China)

2015-08-30

Highlights: • This work aims to develop a long-duration remediation agent (LRA). • LRA was obtained using Na{sub 2}S{sub 2}O{sub 3} supported by attapulgite (ATP) micro–nano networks. • ATP micro–nano networks was induced by high-energy electron beam irradiation. • LRA can effectively control the migration of Cr(VI) and reducing Cr(VI) to Cr(III). • LRA displayed high performance on the remediation of heavy metal contaminated soil. - Abstract: In this work, a long-duration remediation agent (LRA) on hexavalent chromium (Cr(VI)) was developed using sodium thiosulfate (ST) supported by attapulgite (ATP) micro–nano networks induced through high-energy electron beam (HEEB) irradiation. The ATP networks could effectively reduce the leaching amount of Cr(VI) in soil. More importantly, the ATP networks could significantly control the leaching behavior of ST, and then prolong the duration and increase the reduction efficiency of ST on Cr(VI). As a result, LRA displayed high performance on controlling the migration of Cr(VI) and reducing Cr(VI) to Cr(III). Additionally, pot experiment indicated that LRA could effectively decrease the absorbed amount of Cr(VI) in corn, and reduce the inhibition effect of Cr(VI) on the growth of corn. Therefore, this work could provide a facile approach to remediate the Cr(VI)-contaminated soil and lower the harmful effect of Cr(VI) on crop.

Quantitative chemical microdetermination of beryllium with chrome azurol by the ring-oven technique

International Nuclear Information System (INIS)

Hansen, N.B.

1982-01-01

A method for determination of beryllium in minerals and rocks is described. Because of the toxicity of beryllium the method is designed for determination of 1-10 ng of Be. The sample is fused with sodium carbonate and sodium tetraborate. Interfering metals are masked with EDTA. Be is determined by the Weisz ring-oven method with Chrome Azurol. The relative error is 10%. (Author)

40 CFR 425.10 - Applicability; description of the hair pulp, chrome tan, retan-wet finishing subcategory.

Science.gov (United States)

2010-07-01

... ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS LEATHER TANNING AND FINISHING... addition to other unhairing and tanning operation, processes raw or cured cattle or cattle-like hides into finished leather by chemically dissolving the hide hair, chrome tanning, and retan-wet finishing. ...

Green chemistry approaches to leather tanning process for making chrome-free leather by unnatural amino acids

International Nuclear Information System (INIS)

Krishnamoorthy, G.; Sadulla, S.; Sehgal, P.K.; Mandal, Asit Baran

2012-01-01

Highlights: ► Unnatural D-AA assisted tanned leathers found soft and full possessing tight grain. ► Increased hydrothermal stability of collagen via intra and inter molecular crosslink. ► D-Ly+Ald tanned leathers revealed a properly oriented with well aligned structure. ► D-AA in collagen creates new topologies inaccessible to homo chiral molecules. ► Improves conventional tanning process, and reduce the total solid and liquid wastes. - Abstract: In the present study, green and sustainable method or eco-friendly approaches to tanning process based on unnatural D-amino acids (D-AA)-aldehyde (Ald) as a substitute for chrome-free tanning has been attempted. The distribution of optically active D-AA in tanned leather, the hydrothermal stability, the mechanical properties and resistance to collagenolytic activity of tanned leather, the evaluation of eco-friendly characteristics were investigated. Scanning electron microscopic (SEM) and Atomic force microscopic (AFM) analyses indicate the surface morphology and roughness, respectively, of the tanned leather collagen matrix. Shrinkage and Differential scanning calorimetric (DSC) analyses shows that the shrinkage temperature (T s ) and denaturation temperature (T d ) of tanned leather are related to the content of D-AA+Ald present in the leather matrix. It has been found that the T s of D-AA tanned leather is more than that of Ald tanned leather and also more or less equal to chrome tanned leather. Environmental impact assessment (EIA) shows that the developed process results in significant reduction in total solids content (TSC) and improves better biodegradability of organic compound present in the effluent compared to chrome tanning.

Fracturing of revision of a cobalt-chrome femoral head after fracturing of a ceramic femoral head, with diffuse metallosis. Case report

Directory of Open Access Journals (Sweden)

Pedro Miguel Dantas Costa Marques

2013-04-01

Full Text Available We presente a case of a fracture of a cobalt-chrome femoral head after revision of a hip total prosthesis with ceramic femoral head fracture. During surgery we found the cobalt-chrome femoral head fracture, wear of the polyethylene and massive metallosis in muscular and cartilaginous tissue. Both femoral stem and acetabular cup were stable and without apparent wearing. After surgical debridement, we promoted the substitution of the femoral head and the acetabular polyethylene by similar ones. After 12 months of follow-up, the patient has no pain complaints, function limit or systemic signs associated with malign metallosis

Vi, de civiliserede

DEFF Research Database (Denmark)

Nyemann, Dorthe

2016-01-01

Vi har i årtier troet på, at mennesker under de rette omstændigheder kan lykkes med at leve i fred og fordragelighed med hinanden. Skal vi til at erkende, at også vores samfundsstrukturer kun er en tynd fernis ovenpå et utæmmeligt voldspotentiale og egoisme?......Vi har i årtier troet på, at mennesker under de rette omstændigheder kan lykkes med at leve i fred og fordragelighed med hinanden. Skal vi til at erkende, at også vores samfundsstrukturer kun er en tynd fernis ovenpå et utæmmeligt voldspotentiale og egoisme?...

Plutonium(VI) accumulation and reduction by lichen biomass: correlation with U(VI)

International Nuclear Information System (INIS)

Ohnuki, Toshihiko; Aoyagi, Hisao; Kitatsuji, Yoshihiro; Samadfam, Mohammad; Kimura, Yasuhiko; William Purvis, O.

2004-01-01

The uptake of plutonium(VI) and uranium(VI) by lichen biomass was studied in the foliose lichen Parmotrema tinctorum to elucidate the migration behavior of Pu and U in the terrestrial environment. Pu and U uptake by P. tinctorum averaged 0.040±0.010 and 0.055±0.015 g g dry -1 , respectively, after 96 h incubation with 4.0x10 -4 mol l -1 Pu solutions of pH 3, 4 and 5. SEM observations showed that the accumulated Pu is evenly distributed on the upper and lower surfaces of P. tinctorum, in contrast to U(VI), which accumulated in both cortical and medullary layers. UV/VIS absorption spectroscopy demonstrates that a fraction of Pu(VI) in the solution is reduced to Pu(V) by the organic substances released from P. tinctorum, and the accumulated Pu on the surface is reduced to Pu(IV), while U(VI) keeps the oxidation state of VI. Since the solubility of Pu(IV) hydroxides is very low, reduced Pu(VI) does not penetrate to the medullary layers, but is probably precipitated as Pu(IV) hydroxides on the cortical lichen surface. It is concluded that the uptake and reduction of Pu(VI) by lichens is important to determine the mobilization and oxidation states of Pu in the terrestrial environment

Anaerobic bio-removal of uranium (VI) and chromium (VI): Comparison of microbial community structure

International Nuclear Information System (INIS)

Martins, Monica; Faleiro, Maria Leonor; Chaves, Sandra; Tenreiro, Rogerio; Santos, Erika; Costa, Maria Clara

2010-01-01

Several microbial communities, obtained from uranium contaminated and non-contaminated samples, were investigated for their ability to remove uranium (VI) and the cultures capable for this removal were further assessed on their efficiency for chromium (VI) removal. The highest efficiency for removal of both metals was observed on a consortium from a non-contaminated soil collected in Monchique thermal place, which was capable to remove 91% of 22 mg L -1 U(VI) and 99% of 13 mg L -1 Cr(VI). This study revealed that uranium (VI) removing communities have also ability to remove chromium (VI), but when uranium (VI) was replaced by chromium (VI) several differences in the structure of all bacterial communities were observed. TGGE and phylogenetic analysis of 16S rRNA gene showed that the uranium (VI) removing bacterial consortia are mainly composed by members of Rhodocyclaceae family and Clostridium genus. On the other hand, bacteria from Enterobacteriaceae family were detected in the community with ability for chromium (VI) removal. The existence of members of Enterobacteriaceae and Rhodocyclaceae families never reported as chromium or uranium removing bacteria, respectively, is also a relevant finding, encouraging the exploitation of microorganisms with new abilities that can be useful for bioremediation.

Anaerobic bio-removal of uranium (VI) and chromium (VI): Comparison of microbial community structure

Energy Technology Data Exchange (ETDEWEB)

Martins, Monica [Centro de Ciencias do Mar, Universidade do Algarve, Campus de Gambelas, 8005-139 Faro (Portugal); Faleiro, Maria Leonor [IBB - Centro de Biomedicina Molecular e Estrutural, Universidade do Algarve, Campus de Gambelas, 8005-139 Faro (Portugal); Chaves, Sandra; Tenreiro, Rogerio [Universidade de Lisboa, Faculdade de Ciencias, Centro de Biodiversidade, Genomica Integrativa e Funcional (BioFIG), Campus de FCUL, Campo Grande 1749-016 Lisboa (Portugal); Santos, Erika [Centro de Ciencias do Mar, Universidade do Algarve, Campus de Gambelas, 8005-139 Faro (Portugal); Costa, Maria Clara, E-mail: mcorada@ualg.pt [Centro de Ciencias do Mar, Universidade do Algarve, Campus de Gambelas, 8005-139 Faro (Portugal)

2010-04-15

Several microbial communities, obtained from uranium contaminated and non-contaminated samples, were investigated for their ability to remove uranium (VI) and the cultures capable for this removal were further assessed on their efficiency for chromium (VI) removal. The highest efficiency for removal of both metals was observed on a consortium from a non-contaminated soil collected in Monchique thermal place, which was capable to remove 91% of 22 mg L{sup -1} U(VI) and 99% of 13 mg L{sup -1} Cr(VI). This study revealed that uranium (VI) removing communities have also ability to remove chromium (VI), but when uranium (VI) was replaced by chromium (VI) several differences in the structure of all bacterial communities were observed. TGGE and phylogenetic analysis of 16S rRNA gene showed that the uranium (VI) removing bacterial consortia are mainly composed by members of Rhodocyclaceae family and Clostridium genus. On the other hand, bacteria from Enterobacteriaceae family were detected in the community with ability for chromium (VI) removal. The existence of members of Enterobacteriaceae and Rhodocyclaceae families never reported as chromium or uranium removing bacteria, respectively, is also a relevant finding, encouraging the exploitation of microorganisms with new abilities that can be useful for bioremediation.

Green chemistry approaches to leather tanning process for making chrome-free leather by unnatural amino acids

Energy Technology Data Exchange (ETDEWEB)

Krishnamoorthy, G.; Sadulla, S.; Sehgal, P.K. [Central Leather Research Institute, Council of Scientific and Industrial Research (CSIR), Adyar, Chennai 600 020 (India); Mandal, Asit Baran, E-mail: abmandal@hotmail.com [Central Leather Research Institute, Council of Scientific and Industrial Research (CSIR), Adyar, Chennai 600 020 (India)

2012-05-15

Highlights: Black-Right-Pointing-Pointer Unnatural D-AA assisted tanned leathers found soft and full possessing tight grain. Black-Right-Pointing-Pointer Increased hydrothermal stability of collagen via intra and inter molecular crosslink. Black-Right-Pointing-Pointer D-Ly+Ald tanned leathers revealed a properly oriented with well aligned structure. Black-Right-Pointing-Pointer D-AA in collagen creates new topologies inaccessible to homo chiral molecules. Black-Right-Pointing-Pointer Improves conventional tanning process, and reduce the total solid and liquid wastes. - Abstract: In the present study, green and sustainable method or eco-friendly approaches to tanning process based on unnatural D-amino acids (D-AA)-aldehyde (Ald) as a substitute for chrome-free tanning has been attempted. The distribution of optically active D-AA in tanned leather, the hydrothermal stability, the mechanical properties and resistance to collagenolytic activity of tanned leather, the evaluation of eco-friendly characteristics were investigated. Scanning electron microscopic (SEM) and Atomic force microscopic (AFM) analyses indicate the surface morphology and roughness, respectively, of the tanned leather collagen matrix. Shrinkage and Differential scanning calorimetric (DSC) analyses shows that the shrinkage temperature (T{sub s}) and denaturation temperature (T{sub d}) of tanned leather are related to the content of D-AA+Ald present in the leather matrix. It has been found that the T{sub s} of D-AA tanned leather is more than that of Ald tanned leather and also more or less equal to chrome tanned leather. Environmental impact assessment (EIA) shows that the developed process results in significant reduction in total solids content (TSC) and improves better biodegradability of organic compound present in the effluent compared to chrome tanning.

Validation of HVOF WC/Co Thermal Spray Coatings as a Replacement for Hard Chrome Plating on Aircraft Landing Gear

National Research Council Canada - National Science Library

Sartwell, Bruce

2004-01-01

.... This document constitutes the final report on a project to quality high-velocity oxygen-fuel (HVOF) thermal spray WC/Co coatings as a replacement for hard chrome plating on landing gear components...

Poultry feed based on protein hydrolysate derived from chrome-tanned leather solid waste: creating value from waste.

Science.gov (United States)

Chaudhary, Rubina; Pati, Anupama

2016-04-01

Leather industry generates huge amount of chrome-containing leather solid waste which creates major environment problems to tanners worldwide. Chrome-tanned leather solid waste is primarily chromium complex of collagen protein. The presence of chromium limits its protein application in animal feed industry. The purified protein hydrolysate with zero chromium could be used in poultry feed. In this study, an attempt has been made to assess performance of poultry with purified protein hydrolysate as a feed derived from chrome-tanned leather waste as partial replacement of soyabean meal as a sole source of protein for growing broiler chickens. Growth study was conducted to evaluate the effect of feeding protein hydrolysate on performance and physiochemical characteristics of meat of broiler chickens. Two experimental diets containing various levels of protein hydrolysate (EI-20 % and EII-30 %) were evaluated. The comparative study was performed as control with soyabean meal. Daily feed intake, body weight gain and feed conversion ratio were measured from day 8 to day 35. At the end of the study, birds were randomly selected and slaughtered to evaluate for physiochemical characteristics of meat. Diet had significant effects on feed intake and body weight gain. Birds fed with 20 and 30 % protein hydrolysate consumed 9.5 and 17.5 % higher amount of feed and gained 6.5 and 16.6 % higher than soyabean meal-fed birds. The current study produced evidence that protein hydrolysate can replace up to 75 % of soyabean meal in broiler diets without affecting either growth performance or meat characteristics.

II-VI semiconductor compounds

CERN Document Server

1993-01-01

For condensed matter physicists and electronic engineers, this volume deals with aspects of II-VI semiconductor compounds. Areas covered include devices and applications of II-VI compounds; Co-based II-IV semi-magnetic semiconductors; and electronic structure of strained II-VI superlattices.

Effect of liquid waste discharges from steam generating facilities

Energy Technology Data Exchange (ETDEWEB)

McGuire, H.E. Jr.

1977-09-01

This report contains a summary of the effects of liquid waste discharges from steam electric generating facilities on the environment. Also included is a simplified model for use in approximately determining the effects of these discharges. Four basic fuels are used in steam electric power plants: three fossil fuels--coal, natural gas, and oil; and uranium--presently the basic fuel of nuclear power. Coal and uranium are expected to be the major fuels in future years. The following power plant effluents are considered: heat, chlorine, copper, total dissolved solids, suspended solids, pH, oil and grease, iron, zinc, chrome, phosphorus, and trace radionuclides.

Effect of liquid waste discharges from steam generating facilities

International Nuclear Information System (INIS)

McGuire, H.E. Jr.

1977-09-01

This report contains a summary of the effects of liquid waste discharges from steam electric generating facilities on the environment. Also included is a simplified model for use in approximately determining the effects of these discharges. Four basic fuels are used in steam electric power plants: three fossil fuels--coal, natural gas, and oil; and uranium--presently the basic fuel of nuclear power. Coal and uranium are expected to be the major fuels in future years. The following power plant effluents are considered: heat, chlorine, copper, total dissolved solids, suspended solids, pH, oil and grease, iron, zinc, chrome, phosphorus, and trace radionuclides

Influence of Cooling Rate in High-Temperature Area on Hardening of Deposited High-Cutting Chrome-Tungsten Metal

OpenAIRE

Malushin, N. N.; Valuev, Denis Viktorovich; Valueva, Anna Vladimirovna; Serikbol, A.; Borovikov, I. F.

2015-01-01

The authors study the influence of cooling rate in high-temperature area for thermal cycle of high-cutting chrome-tungsten metal weld deposit on the processes of carbide phase merging and austenite grain growth for the purpose of providing high hardness of deposited metal (HRC 64-66).

Cinética e equilíbrio de adsorção dos oxiânions Cr (VI, Mo (VI e Se (VI pelo sal de amônio quaternário de quitosana Kinetics and equilibrium of adsorption of oxyanions Cr (VI, Mo (VI and Se (VI by quaternary ammonium chitosan salt

Directory of Open Access Journals (Sweden)

Viviane A. Spinelli

2005-07-01

Full Text Available O sal quaternário de quitosana foi sintetizado com cloreto de glicidil trimetil amônio. A modificação química foi caracterizada por espectrometria no IV, RMN de 13C e ¹H, e mmol/g de grupos quaternários presentes na matriz polimérica por condutimetria. A remoção de Cr (VI, Mo (VI e Se (VI, em meio aquoso, foi investigada em processo de batelada. A adsorção mostrou ser dependente do pH para o Cr (VI e Se (VI, com um pH ótimo de adsorção, entre 4,0 a 6,0. Para o Mo (VI a adsorção manteve-se quase constante no intervalo de pH entre 4,0 e 11,5. O modelo de isoterma de Langmuir descreveu melhor os dados de equilíbrio na faixa de concentração investigada. No presente estudo, um grama do sal quaternário de quitosana reticulado com glutaraldeído adsorveu 68,3 mg de Cr, 63,4 mg de Mo e 90,0 mg de Se. A velocidade de adsorção, no processo, segue a equação cinética de pseudo segunda-ordem, sendo que o equilíbrio para os três íons foi alcançado próximo aos 200 minutos. A análise dispersiva de raios-X para o Cr (VI mostrou que o principal mecanismo de adsorção é a troca iônica entre os íons Cl- da superfície do polímero pelos oxiânions. O trocador aniônico apresentou a seguinte ordem de seletividade: Cr (VI > Mo (VI > Se (VI.Quaternary chitosan salt was synthesized in the presence of glycidyl trimetyl ammonium chloride. The polymer was characterized by spectroscopic techniques: infrared, 13C and ¹H NMR, while the amount of quaternary ammonium groups was obtained by condutimetry. The removal of Cr (VI, Mo (VI and Se (VI from aqueous solutions was carried out in batch adsorption processes. The process seemed to be pH dependent for Cr (VI and Se (VI with an optimum pH ranging from 4.0 to 6.0; while for Mo (VI the adsorption remained almost constant within the range between 4.0 and 11.5. The Langmuir isotherm model provided the best fit of the equilibrium data over the whole concentration investigated. In the experiment

U(VI) sorption on kaolinite. Effects of pH, U(VI) concentration and oxyanions

International Nuclear Information System (INIS)

Liang Gao; Ziqian Yang; Keliang Shi; Xuefeng Wang; Zhijun Guo; Wangsuo Wu

2010-01-01

U(VI) sorption on kaolinite was studied as functions of contact time, pH, U(VI) concentration, solid-to-liquid ratio (m/V) by using a batch experimental method. The effects of sulfate and phosphate on U(VI) sorption were also investigated. It was found that the sorption kinetics of U(VI) can be described by a pseudo-second-order model. Potentiometric titrations at variable ionic strengths indicated that the titration curves of kaolinite were not sensitive to ionic strength, and that the pH of the zero net proton charge (pH PZNPC ) was at 6.9. The sorption of U(VI) on kaolinite increased with pH up to 6.5 and reached a plateau at pH >6.5. The presence of phosphate strongly increased U(VI) sorption especially at pH <5.5, which may be due to formation of ternary surface complexes involving phosphate. In contrast, the presence of sulfate did not cause any apparent effect on U(VI) sorption. A double layer model was used to interpret both results of potentiometric titrations and U(VI) sorption on kaolinite. (author)

Hexavalent Chrome Free Coatings for Electronics Applications: Joint Test Report

Science.gov (United States)

Kessel, Kurt

2012-01-01

Regardless of the corrosivity of the environment, all metals require periodic maintenance activity to guard against the insidious effects of corrosion and thus ensure that alloys meet or exceed design or performance life. The standard practice for protecting metallic substrates is the application of a coating system. Applied coating systems work via a variety of methods (barrier, galvanic, and/or inhibitor) and adhere to the substrate through a combination of chemical and physical bonds. For years hexavalent chromium has been a widely used element within applied coating systems because of its self healing and corrosion resistant properties. Occupational Safety and Health Administration (OSHA) studies have concluded that hexavalent chromium (hex chrome) is carcinogenic and poses significant risk to human health. On May 5, 2011 amendments to the Defense Federal Acquisition Regulation Supplement (DFARS) were issued in the Federal Register. Subpart 223.73 prohibits contracts from requiring hexavalent chromium in deliverables unless certain exceptions apply. These exceptions include authorization from a general or flag officer and members of the Senior Executive Service from a Program Executive Office, and unmodified legacy systems. Otherwise, Subpart 252.223-7008 provides the contract clause prohibiting contractors from using or delivering hexavalent chromium in a concentration greater than 0.1 percent by weight for all new contracts and to be included down to subcontractors for supplies, maintenance and repair services, and construction materials. National Aeronautics and Space Administration (NASA), Department of Defense (DoD), and industry stakeholders continue to search for alternatives to hex chrome in coatings applications that meet their performance requirements in corrosion protection, cost, operability, and health and safety, while typically specifying that performance must be equal to or greater than existing systems.

KENO-VI Primer: A Primer for Criticality Calculations with SCALE/KENO-VI Using GeeWiz

International Nuclear Information System (INIS)

Bowman, Stephen M.

2008-01-01

The SCALE (Standardized Computer Analyses for Licensing Evaluation) computer software system developed at Oak Ridge National Laboratory is widely used and accepted around the world for criticality safety analyses. The well-known KENO-VI three-dimensional Monte Carlo criticality computer code is one of the primary criticality safety analysis tools in SCALE. The KENO-VI primer is designed to help a new user understand and use the SCALE/KENO-VI Monte Carlo code for nuclear criticality safety analyses. It assumes that the user has a college education in a technical field. There is no assumption of familiarity with Monte Carlo codes in general or with SCALE/KENO-VI in particular. The primer is designed to teach by example, with each example illustrating two or three features of SCALE/KENO-VI that are useful in criticality analyses. The primer is based on SCALE 6, which includes the Graphically Enhanced Editing Wizard (GeeWiz) Windows user interface. Each example uses GeeWiz to provide the framework for preparing input data and viewing output results. Starting with a Quickstart section, the primer gives an overview of the basic requirements for SCALE/KENO-VI input and allows the user to quickly run a simple criticality problem with SCALE/KENO-VI. The sections that follow Quickstart include a list of basic objectives at the beginning that identifies the goal of the section and the individual SCALE/KENO-VI features that are covered in detail in the sample problems in that section. Upon completion of the primer, a new user should be comfortable using GeeWiz to set up criticality problems in SCALE/KENO-VI. The primer provides a starting point for the criticality safety analyst who uses SCALE/KENO-VI. Complete descriptions are provided in the SCALE/KENO-VI manual. Although the primer is self-contained, it is intended as a companion volume to the SCALE/KENO-VI documentation. (The SCALE manual is provided on the SCALE installation DVD.) The primer provides specific examples of

Removal of Cr(VI) from wastewaters at semi-industrial electrochemical reactors with rotating ring electrodes

International Nuclear Information System (INIS)

Rodriguez R, Miriam G.; Mendoza, Victor; Puebla, Hector; Martinez D, Sergio A.

2009-01-01

In Mexico, most of the electroplating and textile industries are small facilities and release relatively large amounts of hexavalent chromium (Cr(VI)) in surface waters. In this work, the results obtained during the operation of a batch reactor with a capacity of 170 L, and three electrochemical flow reactors-in-series system with a total capacity of 510 L (both using iron rotating ring electrodes to remove Cr(VI) from wastewaters) are presented. The reactors were scaled up from a laboratory reactor to a semi-industrial level, based on the similarity (dynamical, geometrical and electrochemical). An empirical Cr(VI) removal model was validated in batch and continuous reactors at different operating conditions. Cr(VI) concentration of the industrial wastewaters was reduced from about 500 mg/L to values lower than 0.5 mg/L. A very important parameter that affects the process is the pH, which affects the solubility of the Fe(III). Finally, the electrochemical treated wastewater can be reused

Removal of Cr(VI) from wastewaters at semi-industrial electrochemical reactors with rotating ring electrodes

Energy Technology Data Exchange (ETDEWEB)

Rodriguez R, Miriam G. [Depto. Energia, Universidad Autonoma Metropolitana-Azcapotzalco, Av. San Pablo 180, Azcapotzalco, CP 07740, Mexico D.F. (Mexico); Mendoza, Victor [Depto. Electronica, Universidad Autonoma Metropolitana-Azcapotzalco, Av. San Pablo 180, Azcapotzalco, CP 07740, Mexico D.F. (Mexico); Puebla, Hector [Depto. Energia, Universidad Autonoma Metropolitana-Azcapotzalco, Av. San Pablo 180, Azcapotzalco, CP 07740, Mexico D.F. (Mexico); Martinez D, Sergio A. [Depto. Energia, Universidad Autonoma Metropolitana-Azcapotzalco, Av. San Pablo 180, Azcapotzalco, CP 07740, Mexico D.F. (Mexico)], E-mail: samd@correo.azc.uam.mx

2009-04-30

In Mexico, most of the electroplating and textile industries are small facilities and release relatively large amounts of hexavalent chromium (Cr(VI)) in surface waters. In this work, the results obtained during the operation of a batch reactor with a capacity of 170 L, and three electrochemical flow reactors-in-series system with a total capacity of 510 L (both using iron rotating ring electrodes to remove Cr(VI) from wastewaters) are presented. The reactors were scaled up from a laboratory reactor to a semi-industrial level, based on the similarity (dynamical, geometrical and electrochemical). An empirical Cr(VI) removal model was validated in batch and continuous reactors at different operating conditions. Cr(VI) concentration of the industrial wastewaters was reduced from about 500 mg/L to values lower than 0.5 mg/L. A very important parameter that affects the process is the pH, which affects the solubility of the Fe(III). Finally, the electrochemical treated wastewater can be reused.

Cranial mononeuropathy VI

Science.gov (United States)

... Abducens palsy; Lateral rectus palsy; VIth nerve palsy; Cranial nerve VI palsy; Sixth nerve palsy; Neuropathy - sixth nerve ... Cranial mononeuropathy VI is damage to the sixth cranial nerve. This nerve is also called the abducens nerve. ...

Influence of Cooling Rate in High-Temperature Area on Hardening of Deposited High-Cutting Chrome-Tungsten Metal

International Nuclear Information System (INIS)

Malushin, N N; Valuev, D V; Valueva, A V; Serikbol, A; Borovikov, I F

2015-01-01

The authors study the influence of cooling rate in high-temperature area for thermal cycle of high-cutting chrome-tungsten metal weld deposit on the processes of carbide phase merging and austenite grain growth for the purpose of providing high hardness of deposited metal (HRC 64-66). (paper)

Chrome-free Samarium-based Protective Coatings for Magnesium Alloys

Science.gov (United States)

Hou, Legan; Cui, Xiufang; Yang, Yuyun; Lin, Lili; Xiao, Qiang; Jin, Guo

The microstructure of chrome-free samarium-based conversion coating on magnesium alloy was investigated and the corrosion resistance was evaluated as well. The micro-morphology, transverse section, crystal structure and composition of the coating were observed by scanning electron microscopy (SEM), X-ray diffraction (XRD), energy dispersive spectroscopy (EDS) and X- ray photoelectron spectroscopy (XPS), respectively. The corrosion resistance was evaluated by potentiodynamic polarization curve and electrochemical impedance spectroscopy (EIS). The results reveal that the morphology of samarium conversion coating is of crack-mud structure. Tiny cracks distribute in the compact coating deposited by samarium oxides. XRD, EDS and XPS results characterize that the coating is made of amorphous and trivalent-samarium oxides. The potentiodynamic polarization curve, EIS and OCP indicate that the samarium conversion coating can improve the corrosion resistance of magnesium alloys.

Removal of hexavalent chromium from wastewater using a new composite chitosan biosorbent.

Science.gov (United States)

Boddu, Veera M; Abburi, Krishnaiah; Talbott, Jonathan L; Smith, Edgar D

2003-10-01

A new composite chitosan biosorbent was prepared by coating chitosan, a glucosamine biopolymer, onto ceramic alumina. The composite bioadsorbent was characterized by high-temperature pyrolysis, porosimetry, scanning electron microscopy, and X-ray photoelectron spectroscopy. Batch isothermal equilibrium and continuous column adsorption experiments were conducted at 25 degrees C to evaluate the biosorbent for the removal of hexavalent chromium from synthetic as well as field samples obtained from chrome plating facilities. The effect of pH, sulfate, and chloride ion on adsorption was also investigated. The biosorbent loaded with Cr(VI) was regenerated using 0.1 M sodium hydroxide solution. A comparison of the results of the present investigation with those reported in the literature showed that chitosan coated on alumina exhibits greater adsorption capacity for chromium(VI). Further, experimental equilibrium data were fitted to Langmuir and Freundlich adsorption isotherms, and values of the parameters of the isotherms are reported. The ultimate capacity obtained from the Langmuir model is 153.85 mg/g chitosan.

Enzymatic reduction of U(VI) in groundwaters; Reduction enzymatique de U(VI) dans des eaux souterraines

Energy Technology Data Exchange (ETDEWEB)

Addelouas, A.; Gong, W. [Center for Radioactive Waste Management, Advanced Materials Laboratory, 1001 University, Albuquerque (United States); Lutze, W.; Nuttall, E. [New Mexico Univ., Albuquerque, NM (United States). Dept. of Chemical and Nuclear Engineering; Fritz, B.; Crovisier, J.L. [Centre National de la Recherche Scientifique (CNRS), 67 - Strasbourg (France). Centre de Sedimentologie et Geochimie de la Surface

1999-03-01

The use of enzymatic reduction of U(VI) in remediation of groundwater contaminated with U(VI) is receiving considerable attention. Certain strains of bacteria can combine the oxidation of an organic compound to the reduction of U(VI) to U(IV), which precipitates as uraninite. In the present study, we tested the reduction of U(VI) in groundwaters with various origins and compositions. In all groundwaters u(VI) was reduced by sulfate reducing bacteria that had been activated by ethanol and tri-metaphosphate. The reduction rate of U(VI) depends on sulfate concentration in water and the abundance of bacteria in the system. This work shows that bacteria capable of U(VI) reduction are ubiquitous in nature, and suggests the possibility of a large application of the enzymatic reduction of U(VI) for in situ clean up of groundwaters contaminated with uranium. (authors) 12 refs.

Chrome-tanned leather shavings as a filler of butadiene-acrylonitrile rubber.

Science.gov (United States)

Przepiórkowska, A; Chrońska, K; Zaborski, M

2007-03-06

The noxious wastes from the tanning industry such as chrome-tanned leather shavings were used as the only filler of rubber mixes containing carboxylated butadiene-acrylonitrile rubber (XNBR) or butadiene-acrylonitrile rubber (NBR), and a dispersing agent Limanol PEV (Schill & Seilacher). The best form addition of leather powder to the rubber mixes is mixed the waste protein with zinc oxide. The leather powder added to the rubber mixes improves the mechanical properties: tensile strength (T(s)), elongation at break (epsilon(b)) and increase the cross-linking density of carboxylated XNBR and NBR rubber mixes. Satisfactory results of these studies are presented in this work.

Automated System Calibration and Verification of the Position Measurements for the Los Alamos Isotope Production Facility and the Switchyard Kicker Facilities

Science.gov (United States)

Barr, D.; Gilpatrick, J. D.; Martinez, D.; Shurter, R. B.

2004-11-01

The Los Alamos Neutron Science Center (LANSCE) facility at Los Alamos National Laboratory has constructed both an Isotope Production Facility (IPF) and a Switchyard Kicker (XDK) as additions to the H+ and H- accelerator. These additions contain eleven Beam Position Monitors (BPMs) that measure the beam's position throughout the transport. The analog electronics within each processing module determines the beam position using the log-ratio technique. For system reliability, calibrations compensate for various temperature drifts and other imperfections in the processing electronics components. Additionally, verifications are periodically implemented by a PC running a National Instruments LabVIEW virtual instrument (VI) to verify continued system and cable integrity. The VI communicates with the processor cards via a PCI/MXI-3 VXI-crate communication module. Previously, accelerator operators performed BPM system calibrations typically once per day while beam was explicitly turned off. One of this new measurement system's unique achievements is its automated calibration and verification capability. Taking advantage of the pulsed nature of the LANSCE-facility beams, the integrated electronics hardware and VI perform calibration and verification operations between beam pulses without interrupting production beam delivery. The design, construction, and performance results of the automated calibration and verification portion of this position measurement system will be the topic of this paper.

Information profiles on potential occupational hazards: Inorganic chromium compounds. Draft report (Second)

Energy Technology Data Exchange (ETDEWEB)

1982-02-01

Information profiles are presented for the following inorganic chromium compounds: chromic(VI) acid, chromic(III) hydroxide, chromic(III) oxide, chromic(III) sulfate, chromic(III) sulfate (basic), chromium dioxide, potassium dichromate(VI), lead chromate, sodium-chromate(VI), sodium-dichromate(VI), and zinc-yellow-chromate(VI). Biological effects of hexavalent chromium in humans included skin ulceration, dermatitis, nasal membrane irritation and ulceration, nasal septal perforation, rhinitis, nosebleed, nephritis, liver damage, epigastric pain, pulmonary congestion and edema, and erosion and discoloration of teeth. Chromium(VI) compounds caused mutations in a variety of systems. Exposure to trivalent chromium in the work place has caused contact dermatitis and chrome ulcers. Epidemiological studies indicated respiratory carcinogenicity among workers occupationally exposed during chromate production.

Nucleotide sequence of Hungarian grapevine chrome mosaic nepovirus RNA1.

Science.gov (United States)

Le Gall, O; Candresse, T; Brault, V; Dunez, J

1989-10-11

The nucleotide sequence of the RNA1 of hungarian grapevine chrome mosaic virus, a nepovirus very closely related to tomato black ring virus, has been determined from cDNA clones. It is 7212 nucleotides in length excluding the 3' terminal poly(A) tail and contains a large open reading frame extending from nucleotides 216 to 6971. The presumably encoded polyprotein is 2252 amino acids in length with a molecular weight of 250 kDa. The primary structure of the polyprotein was compared with that of other viral polyproteins, revealing the same general genetic organization as that of other picorna-like viruses (comoviruses, potyviruses and picornaviruses), except that an additional protein is suspected to occupy the N-terminus of the polyprotein.

Compositional Variation of Chrome Spinels in the Ore-bearing Zones of the Kraka Ophiolite and the Chromitite Origin

Directory of Open Access Journals (Sweden)

D. E. Saveliev

2017-07-01

Full Text Available The article considers a chemical variation of accessory and ore-forming chrome spinels from the Kraka ultramafic massif at the different scales, from the deposit to the thin section. A correlation analysis of compositional and structural features of ultramafic rocks and ores was performed. The ultramafic rocks and chromitites in the studied massif show the distinct deformation structures and tectonite olivine fabric. A typical chemical gap (i.e. Cr#=Cr/(Cr+Al was observed between peridotite, on the one hand, and dunite and chromitite, on the other hand, on the scale of deposits and ore-bearing zones. The location and size of this gap depend on the type of deposit. The gap becomes wider from the disseminated tabular bodies to the typical podiform ones. It has been found that in the thin initial dunite veinlets in peridotite the chrome spinels chemistry changes gradually and there is no Cr# gap between peridotite and dunite. The dunite venlets show a strong olivine fabric, which is an evidence of their high-temperature plastic flow origin. It has been revealed that new chrome spinel grains previously formed as rods or needles and then coarsened. We explained this observation as the result of impurity segregation, coalescence and spheroidization induced by the plastic deformation of olivine. It is inferred that a solid crystal flow is the main requirement for the dunite and chromitite body formation in the Kraka ophiolite massif. In the solid stream, the mineral phase separation takes place. For example, olivine and orthopyroxene grains of parental peridotite separate from one another, and weaker (more mobile olivine grains form dunite bodies in which chromitite appears as a result of impurity segregation.

Formation of stable uranium(VI) colloidal nanoparticles in conditions relevant to radioactive waste disposal.

Science.gov (United States)

Bots, Pieter; Morris, Katherine; Hibberd, Rosemary; Law, Gareth T W; Mosselmans, J Frederick W; Brown, Andy P; Doutch, James; Smith, Andrew J; Shaw, Samuel

2014-12-09

The favored pathway for disposal of higher activity radioactive wastes is via deep geological disposal. Many geological disposal facility designs include cement in their engineering design. Over the long term, interaction of groundwater with the cement and waste will form a plume of a hyperalkaline leachate (pH 10-13), and the behavior of radionuclides needs to be constrained under these extreme conditions to minimize the environmental hazard from the wastes. For uranium, a key component of many radioactive wastes, thermodynamic modeling predicts that, at high pH, U(VI) solubility will be very low (nM or lower) and controlled by equilibrium with solid phase alkali and alkaline-earth uranates. However, the formation of U(VI) colloids could potentially enhance the mobility of U(VI) under these conditions, and characterizing the potential for formation and medium-term stability of U(VI) colloids is important in underpinning our understanding of U behavior in waste disposal. Reflecting this, we applied conventional geochemical and microscopy techniques combined with synchrotron based in situ and ex situ X-ray techniques (small-angle X-ray scattering and X-ray adsorption spectroscopy (XAS)) to characterize colloidal U(VI) nanoparticles in a synthetic cement leachate (pH > 13) containing 4.2-252 μM U(VI). The results show that in cement leachates with 42 μM U(VI), colloids formed within hours and remained stable for several years. The colloids consisted of 1.5-1.8 nm nanoparticles with a proportion forming 20-60 nm aggregates. Using XAS and electron microscopy, we were able to determine that the colloidal nanoparticles had a clarkeite (sodium-uranate)-type crystallographic structure. The presented results have clear and hitherto unrecognized implications for the mobility of U(VI) in cementitious environments, in particular those associated with the geological disposal of nuclear waste.

Uranium(VI) speciation by spectroscopy

International Nuclear Information System (INIS)

Meinrath, G.

1997-01-01

The application of UV-Vis and time-resolved laser-induced fluorescence (TRLF) spectroscopies to direct of uranium(VI) in environmental samples offers various prospects that have, however, serious limitations. While UV-Vis spectroscopy is probably not sensitive enough to detect uranium(VI) species in the majority of environmental samples, TRLFS is principially able to speciate uranium(VI) at very low concentration levels in the nanomol range. Speciation by TRLFS can be based on three parameters: excitation spectrum, emission spectrum and lifetime of the fluorescence emission process. Due to quenching effects, the lifetime may not be expected to be as characteristics as, e.g., the emission spectrum. Quenching of U(VI) fluorescence by reaction with organic substances, inorganic ions and formation of carbonate radicals is one important limiting factor in the application of U(VI) fluorescence spectroscopy. Fundamental photophysical criteria are illustrated using UV-Vis and fluorescence spectra of U(VI) hydrolysis and carbonato species as examples. (author)

Characterization of emission factors related to source activity for trichloroethylene degreasing and chrome plating processes.

Science.gov (United States)

Wadden, R A; Hawkins, J L; Scheff, P A; Franke, J E

1991-09-01

A study at an automotive parts fabrication plant evaluated four metal surface treatment processes during production conditions. The evaluation provides examples of how to estimate process emission factors from activity and air concentration data. The processes were open tank and enclosed tank degreasing with trichloroethylene (TCE), chromium conversion coating, and chromium electroplating. Area concentrations of TCE and chromium (Cr) were monitored for 1-hr periods at three distances from each process. Source activities at each process were recorded during each sampling interval. Emission rates were determined by applying appropriate mass balance models to the concentration patterns around each source. The emission factors obtained from regression analysis of the emission rate and activity data were 16.9 g TCE/basket of parts for the open-top degreaser; 1.0 g TCE/1000 parts for the enclosed degreaser; 1.48-1.64 mg Cr/1000 parts processed in the hot CrO3/HNO3 tank for the chrome conversion coating; and 5.35-9.17 mg Cr/rack of parts for chrome electroplating. The factors were also used to determine the efficiency of collection for the local exhaust systems serving each process. Although the number of observations were limited, these factors may be useful for providing initial estimates of emissions from similar processes in other settings.

Google Chrome OS: Cultural influence on product launch strategy between India and developed countries

OpenAIRE

Santhosh, Arjun

2011-01-01

In recent times product launch has become vital deciding factor in the success of a product. The significance of product launch becomes even higher if the product is radically new and different from existing products in the market. The aim of this dissertation is to look into the possible factors which might influence the product launch of Google Chrome Operating System that has radical concepts and design. The essential variations which might be needed for the successful launch in India as c...

PHOTOCATALYTIC REMOVAL OF TR I- AND HEXA-VALENT CHROMIUM IONS FROM CHROME-ELECTROPL ATING WASTEWATER

OpenAIRE

Puangrat Kajitvichyanukul; Chulaluck Changul

2017-01-01

A novel technique based on photocatalysis was applied to eliminate chromium ions, a toxic hazardous environmental pollutant. The photoreduction of each species of chromium (total, hexavalent, and trivalent chromiums) from chrome-electroplating wastewater was investigated using a titanium dioxide suspension under irradiation by a low-pressure mercury lamp. The initial concentration of total chromium was 300 mg/l. The applied conditions were the direct photocatalytic reduction process at pH 3.6...

Diverse anaerobic Cr(VI) tolerant bacteria from Cr(VI)-contaminated 100H site at Hanford

Science.gov (United States)

Chakraborty, R.; Phan, R.; Lam, S.; Leung, C.; Brodie, E. L.; Hazen, T. C.

2007-12-01

Hexavalent Chromium [Cr(VI)] is a widespread contaminant found in soil, sediment, and ground water. Cr(VI) is more soluble, toxic, carcinogenic, and mutagenic compared to its reduced form Cr(III). In order to stimulate microbially mediated reduction of Cr(VI), a poly-lactate compound HRC was injected into the chromium contaminated aquifers at site 100H at Hanford. Based on the results of the bacterial community composition using high-density DNA microarray analysis of 16S rRNA gene products, we recently investigated the diversity of the dominant anaerobic culturable microbial population present at this site and their role in Cr(VI) reduction. Positive enrichments set up at 30°C using specific defined anaerobic media resulted in the isolation of an iron reducing isolate strain HAF, a sulfate reducing isolate strain HBLS and a nitrate reducing isolate, strain HLN among several others. Preliminary 16S rDNA sequence analysis identifies strain HAF as Geobacter metallireducens, strain HLN as Pseudomonas stutzeri and strain HBLS as a member of Desulfovibrio species. Strain HAF isolated with acetate as the electron donor utilized propionate, glycerol and pyruvate as alternative carbon sources, and reduced metals like Mn(IV) and Cr(VI). Growth was optimal at 37°C, pH of 6.5 and 0% salinity. Strain HLN isolated with lactate as electron donor utilized acetate, glycerol and pyruvate as alternative carbon sources, and reduced metals like Mn(IV) and Cr(VI). Optimal growth was observed at 37°C, at a pH of 7.5 and 0.3% salinity. Anaerobic active washed cell suspension of strain HLN reduced almost 95 micromolar Cr(VI) within 4 hours relative to controls. Further, with 100 micromolar Cr(VI) as the sole electron acceptor, cells of strain HLN grew to cell numbers of 4.05X 107/ml over a period of 24hrs after an initial lag, demonstrating direct enzymatic Cr(VI) reduction by this species. 10mM lactate served as the sole electron donor. These results demonstrate that Cr(VI

Sensitive and selective electrochemical detection of chromium(VI) based on gold nanoparticle-decorated titania nanotube arrays.

Science.gov (United States)

Jin, Wei; Wu, Guosheng; Chen, Aicheng

2014-01-07

Owing to the severe toxicity and mobility of Cr(VI) in biological and environmental systems, it is of great importance to develop convenient and reliable methods for its detection. Here we report on a facile and effective electrochemical technique for monitoring Cr(VI) concentrations based on the utilization of Au nanoparticle-decorated titania nanotubes (TiO2NTs) grown on a titanium substrate. It was found that the electrochemical reduction of Cr(VI) at the Ti/TiO2NT/Au electrode exhibited an almost 23 fold improvement in activity as compared to a polycrystalline gold electrode, due to its nanoparticle/nanotubular heterojunction infrastructure. As a result, the Ti/TiO2NT/Au electrode demonstrated a wide linear concentration range from 0.10 μM to 105 μM, a low detection limit of 0.03 μM, and a high sensitivity of 6.91 μA μM(-1) Cr(VI) via amperometry, satisfying the detection requirements of the World Health Organization (WHO). Moreover, the Ti/TiO2NT/Au electrode exhibited good resistance against interference from coexisting Cr(III) and other metal ions, and excellent recovery for Cr(VI) detection in both tap and lake water samples. These attributes suggest that this hybrid sensor has strong potential in applications for the selective detection of Cr(VI).

Operating procedures for the Pajarito Site Critical Assembly Facility

International Nuclear Information System (INIS)

Malenfant, R.E.

1983-03-01

Operating procedures consistent with DOE Order 5480.2, Chapter VI, and the American National Standard Safety Guide for the Performance of Critical Experiments are defined for the Pajarito Site Critical Assembly Facility of the Los Alamos National Laboratory. These operating procedures supersede and update those previously published in 1973 and apply to any criticality experiment performed at the facility

Enzymatic reduction of U(VI) in groundwaters

International Nuclear Information System (INIS)

Addelouas, A.; Gong, W.; Lutze, W.; Nuttall, E.; Fritz, B.; Crovisier, J.L.

1999-01-01

The use of enzymatic reduction of U(VI) in remediation of groundwater contaminated with U(VI) is receiving considerable attention. Certain strains of bacteria can combine the oxidation of an organic compound to the reduction of U(VI) to U(IV), which precipitates as uraninite. In the present study, we tested the reduction of U(VI) in groundwaters with various origins and compositions. In all groundwaters u(VI) was reduced by sulfate reducing bacteria that had been activated by ethanol and tri-metaphosphate. The reduction rate of U(VI) depends on sulfate concentration in water and the abundance of bacteria in the system. This work shows that bacteria capable of U(VI) reduction are ubiquitous in nature, and suggests the possibility of a large application of the enzymatic reduction of U(VI) for in situ clean up of groundwaters contaminated with uranium. (authors)

25 Utilisation d'un nouveau bio-floculant extrait de cactus marocain ...

African Journals Online (AJOL)

AKA BOKO

chimique (coagulation floculation) afin de traiter des rejets liquides chargés en chrome. (VI). Ce bio-floculant nous a permis de réduire la turbidité d'un effluent industriel, en .... Spectrophotomètre UV-Visible, type UV-160 mode SHIMADZU.

Enzymatic U(VI) reduction by Desulfosporosinus species

International Nuclear Information System (INIS)

Suzuki, Y.; Kelly, S.D.; Kemner, K.M.; Banfield, J.F.

2004-01-01

Here we tested U(VI) reduction by a Desulfosporosinus species (sp.) isolate and type strain (DSM 765) in cell suspensions (pH 7) containing 1 mM U(VI) and lactate, under an atmosphere containing N 2 -CO 2 -H 2 (90: 5: 5). Although neither Desulfosporosinus species (spp.) reduced U(VI) in cell suspensions with 0.25% Na-bicarbonate or 0.85% NaCl, U(VI) was reduced in these solutions by a control strain, desulfovibrio desulfuricans (ATCC 642). However, both Desulfosporosinus strains reduced U(VI) in cell suspensions depleted in bicarbonate and NaCl. No U(VI) reduction was observed without lactate and H 2 electron donors or with heat-killed cells, indicating enzymatic U(VI) reduction. Uranium(VI) reduction by both strains was inhibited when 1 mM CuCl 2 was added to the cell suspensions. Because the Desulfosporosinus DSM 765 does not contain cytochrome c 3 used by Desulfovibrio spp. to reduce U(VI), Desulfosporosinus species reduce uranium via a different enzymatic pathway. (orig.)

Kiintoainehäviöselvitys

OpenAIRE

Ylimys, Jussi

2014-01-01

Teoriaosassa käydään läpi yleisesti pyörrepuhdistuslaitoksen toimintaa sekä kiintoainehäviöitä paperi- ja kartonkitehtailla. Tämän opinnäytetyön tarkoituksena oli tutkia Metsä Boardin Kyröskosken tehtaan kiintoainehäviötä. Työssä selvitettiin, minkälaista kiintoainetta jätevesilaitokselle päätyy ja miksi. Selvityksen kohteena oli myös, missä kohteissa kiintoainehäviöt tarkalleen syntyvät ja kuinka paljon häviötä tapahtuu. Kahden edellä mainitun tiedon perusteella selvitettiin, kuinka palj...

Peroxo complexes of molybdenum(VI), tungsten(VI), uranium(VI), zirconium(IV) and thorium(IV) ions containing tridentate Schiff bases derived from salicylaldehyde and amino acids

International Nuclear Information System (INIS)

Tarafder, M.T.H.; Khan, A.R.

1997-01-01

The synthesis of peroxo complexes of molybdenum(VI), tungsten(VI), uranium(VI), zirconium(IV), thorium(IV) and their possible oxygen transfer reactions is presented. An attempt has also been made to study the size of the metal ions and the electronic effect derived from the tridentate Schiff bases on the v 1 (O-O) mode of the complexes in their IR spectra

DNA-protein crosslinks in peripheral lymphocytes of individuals exposed to hexavalent chromium compounds.

Science.gov (United States)

Zhitkovich, A; Lukanova, A; Popov, T; Taioli, E; Cohen, H; Costa, M; Toniolo, P

1996-01-01

Abstract DNA-protein crosslinks were measured in peripheral blood lymphocytes of chrome-platers and controls from Bulgaria in order to evaluate a genotoxic effect of human exposure to carcinogenic Cr(VI) compounds. Chrome-platers and most of the unexposed controls were from the industrial city of Jambol; some additional controls were recruited from the seaside town of Burgas. The chrome-platers had significantly elevated levels of chromium in pre- and post-shift urine, erythrocytes and lymphocytes compared with the control subjects. The largest differences between the two groups were found in erythrocyte chromium concentrations which are considered to be indicative of Cr(VI) exposure. Despite the significant differences in internal chromium doses, levels of DNA-protein crosslinks were not significantly different between the combined controls and exposed workers. Individual DNA-protein crosslinks, however, correlated strongly with chromium in erythrocytes at low and moderate doses but at high exposures, such as among the majority of chrome-platers, these DNA adducts were saturated at maximum levels. The saturation of DNA-protein crosslinks seems to occur at 7-8 μg I-(1) chromium in erythrocytes whereas a mean erythrocyte chromium among the chrome platers was as high as 22.8 μg l(-1). Occupationally unexposed subjects exhibited a significant variability with respect to the erythrocyte chromium concentration, however erythrocyte chromium levels correlated closely with DNA-protein crosslinks in lymphocytes. The controls from Jambol had higher chromium concentrations in erythrocytes and elevated levels of DNA-protein crosslinks compared with Burgas controls. Occupational exposure to formaldehyde among furniture factory workers did not change levels of DNA-protein crosslinks in peripheral lymphocytes. DNA-protein crosslink measurements showed a low intraindividual variability and their levels among both controls and exposed indivduals were not affected by smoking, age

Risk factors for visual impairment and blindness amongst black adult diabetics receiving treatment at Government healthcare facilities in Mopani District, Limpopo province, South Africa.

Science.gov (United States)

Mabaso, Raymond G; Oduntan, Olalekan A

2014-11-21

Diabetes mellitus (DM) is a common systemic disease amongst Black South Africans. It may lead to diabetic retinopathy (DR), a common cause of visual impairment (VI) and blindness. DR may signifiantly increase the prevalence of VI and blindness. To assess risk factors for VI and blindness amongst a black diabetic South African population aged ≥ 40 years. The study was conducted in seven Government healthcare facilities (two hospitals, four clinics and one health centre) in Mopani District, Limpopo province, South Africa. This was a cross-sectional health facility-based quantitative study. Structured interviews were used to obtain information, which included sociodemographic profie, knowledge about DM and its ocular complications, presence of hypertension and accessibility to health facilities. Subsequently participants were examined for VI and blindness using an autorefractor, pinhole disc, ophthalmoscope and logMAR visual acuity chart. Anthropometric measurements (height, weight and waist) were also taken. Associations between 31 risk factors and VI as well as blindness were statistically examined. Participants (N = 225) included 161 women and 64 men aged 40-90 years (mean 61.5 ± 10.49 years); 41.3% of them had VI and 3.6% were blind. Cataracts (76.8%) and DR (7.1%) were the common causes of compensated VI and blindness. Risk factors that were associated with VI and blindness were age, monthly income, compliance with losing weight and physical activity. Findings suggest that lifestyle intervention and appropriate eyecare programmes may reduce VI and blindness in this population.

The electrochemical aspect of the corrosion of austenitic stainless steels, in nitric acid and in the presence of hexavalent chromium (1961); Aspect electrochimique de la corrosion d'aciers inoxydables austenitiques en milieu nitrique et en presence de chrome hexavalent (1961)

Energy Technology Data Exchange (ETDEWEB)

Coriou, H; Hure, J; Plante, G [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1961-07-01

The corrosion of austenitic stainless steels in boiling nitric acid markedly increases when the medium contains hexavalent chromium ions. Because of several redox phenomena, the potential of the steel generally changes in course of time. Measurements show a relation between the weight loss and the potential of specimens. Additions of Mn(VII) and Ce(IV) are compared with that of Cr(VI), and show that the relation is a general one. The attack cf the metal in oxidizing media is largely intergranular, leading to exfoliation of the grains, although the steel studied is not sensitive to the classical Huey and Strauss tests. Also even in the absence of any other oxidizing reaction, the current density observed when the steel is anodically polarized under potentiostatic conditions does not correspond to the actual weight loss of the metal. (authors) [French] La corrosion d'aciers inoxydables austenitiques en milieu nitrique bouillant augmente notablement quand le milieu contient des ions chrome a l'etat hexavalent. Par suite de divers phenomenes d'oxydo-reduction, le potentiel de l'acier evolue generalement au cours du temps. Les mesures effectuees permettent d'etablir une relation entre les pertes de poids et le potentiel des echantillons. L'addition de Mn(VI) et Ce(IV) est compare a celle de Cr(VI) et montre que la relation precedente s'applique de facon generale. L'attaque du metal en milieu oxydant est en grande, partie due a une corrosion intergranulaire conduisant a un dechaussement des grains bien que l'acier etudie ne soit pas sensible aux tests classiques de Huey et de Strauss. Aussi, meme en l'absence de toute autre reaction d'oxydation l'intensite qu l'on observerait en soumettant l'acier a un potentiel anodique dans un montage potentiostatique ne correspondrait pas a la perte de poids reelle du metal. (auteurs)

ENDF-201, ENDF/B-VI summary documentation supplement 1, ENDF/HE-VI summary documentation

International Nuclear Information System (INIS)

McLane, V.

1996-12-01

The National Nuclear Data Center (NNDC) provides coordination for and serves as the secretariat to the Cross Section Evaluation Working Group (CSWEG). CSEWG is responsible for the oversight of the ENDF/B Evaluated Nuclear Data File. All data are checked and reviewed by CSEWG, and the file is maintained at the NNDC. For a description of the ENDF/B-VI file, see the ENDF-102 Data Formats and Procedures for the Evaluated Nuclear Data File ENDF-6. The purpose of this addendum to the ENDF/B-VI Summary Documentation is to provide documentation of Releases 1, 2, 3, and 4 for the ENDF/B-VI and ENDF/HE-VI evaluated nuclear data libraries. These releases contain many new and revised evaluations for the neutron, photo-atomic interaction, radioactive decay data, spontaneous fission product yield, neutron-induced fission product yield, thermal neutron scattering, proton, deuteron, and triton sublibraries. The summaries have been extracted mainly from the ENDF/B-VI File 1 comments (MT = 451), which have been checked, edited, and may also include supplementary information. Some summaries have been provided by the evaluators in electronic format, while others are extracted from reports on the evaluations. All references have been checked and corrected, or updated where appropriate. A list of the laboratories which have contributed evaluations used in ENDF/B-VI is given

ENDF-201, ENDF/B-VI summary documentation supplement 1, ENDF/HE-VI summary documentation

Energy Technology Data Exchange (ETDEWEB)

McLane, V.

1996-12-01

The National Nuclear Data Center (NNDC) provides coordination for and serves as the secretariat to the Cross Section Evaluation Working Group (CSWEG). CSEWG is responsible for the oversight of the ENDF/B Evaluated Nuclear Data File. All data are checked and reviewed by CSEWG, and the file is maintained at the NNDC. For a description of the ENDF/B-VI file, see the ENDF-102 Data Formats and Procedures for the Evaluated Nuclear Data File ENDF-6. The purpose of this addendum to the ENDF/B-VI Summary Documentation is to provide documentation of Releases 1, 2, 3, and 4 for the ENDF/B-VI and ENDF/HE-VI evaluated nuclear data libraries. These releases contain many new and revised evaluations for the neutron, photo-atomic interaction, radioactive decay data, spontaneous fission product yield, neutron-induced fission product yield, thermal neutron scattering, proton, deuteron, and triton sublibraries. The summaries have been extracted mainly from the ENDF/B-VI File 1 comments (MT = 451), which have been checked, edited, and may also include supplementary information. Some summaries have been provided by the evaluators in electronic format, while others are extracted from reports on the evaluations. All references have been checked and corrected, or updated where appropriate. A list of the laboratories which have contributed evaluations used in ENDF/B-VI is given.

24 CFR 971.11 - HOPE VI developments.

Science.gov (United States)

2010-04-01

... 24 Housing and Urban Development 4 2010-04-01 2010-04-01 false HOPE VI developments. 971.11... § 971.11 HOPE VI developments. Developments with HOPE VI implementation grants that have approved HOPE... with reasonable revitalization plans. Future HUD actions to approve or deny proposed HOPE VI...

CORROSION STUDY FOR THE EFFLUENT TREATMENT FACILITY CHROME (VI) REDUCTANT SOLUTION USING 304 AND 316L STAINLESS STEEL

Energy Technology Data Exchange (ETDEWEB)

DUNCAN JB; WYRAS RB

2007-10-08

This report documents the laboratory testing and analyses as directed under the test plan, RPP PLAN-34065, and documented in laboratory notebooks HNF 2742 and HNF-N-473-1. The purpose of this study was to evaluate and compare the electrochemical corrosion and pitting susceptibility of the 304 and 316L stainless steel in the acidified reducing solution that will be contained in either the secondary waste receiving tank or concentrate tank.

Technology-derived storage solutions for stabilizing insulin in extreme weather conditions I: the ViViCap-1 device.

Science.gov (United States)

Pfützner, Andreas; Pesach, Gidi; Nagar, Ron

2017-06-01

Injectable life-saving drugs should not be exposed to temperatures 30°C/86°F. Frequently, weather conditions exceed these temperature thresholds in many countries. Insulin is to be kept at 4-8°C/~ 39-47°F until use and once opened, is supposed to be stable for up to 31 days at room temperature (exception: 42 days for insulin levemir). Extremely hot or cold external temperature can lead to insulin degradation in a very short time with loss of its glucose-lowering efficacy. Combined chemical and engineering solutions for heat protection are employed in ViViCap-1 for disposable insulin pens. The device works based on vacuum insulation and heat consumption by phase-change material. Laboratory studies with exposure of ViViCap-1 to hot outside conditions were performed to evaluate the device performance. ViViCap-1 keeps insulin at an internal temperature phase-change process and 'recharges' the device for further use. ViViCap-1 performed within its specifications. The small and convenient device maintains the efficacy and safety of using insulin even when carried under hot weather conditions.

Reduction of ferrate(VI) and oxidation of cyanate in a Fe(VI)-TiO2-UV-NCO- system.

Science.gov (United States)

Winkelmann, Kurt; Sharma, Virender K; Lin, Yekaterina; Shreve, Katherine A; Winkelmann, Catherine; Hoisington, Laura J; Yngard, Ria A

2008-08-01

The aqueous photocatalytic degradation of cyanate (NCO(-)), which is a long-lived neurotoxin formed during the remediation of cyanide in industrial waste streams, was studied in the ferrate(VI)-UV-TiO2-NCO(-) system. Kinetics measurements of the photocatalytic reduction of ferrate(VI) were carried out as a function of [NCO(-)], [ferrate(VI)], [O(2)], light intensity (I(o)), and amount of TiO2 in suspensions at pH 9.0. The photocatalytic reduction rate of ferrate(VI) in the studied system can be expressed as -d[Fe(VI)]/dt=kI(o)(0.5) [NCO(-)] [TiO2]. The rate of photocatalytic oxidation of cyanate with ferrate(VI) was greater than the rate in the analogous system without ferrate(VI). The possibility of involvement of reactive ferrate(V) species for this enhancement was determined by studying the reactivity of ferrate(V) with NCO(-) in a homogeneous solution using a premix pulse radiolysis technique. The rate constant for the reaction of ferrate(V) and NCO(-) in alkaline medium was estimated to be (9.60+/-0.07) x 10(2) M(-1) s(-1), which is much slower than the ferrate(VI) self-decomposition reaction (k approximately 10(7) M(-1) s(-1)). An analysis of the kinetic data in the Fe(VI)-UV-TiO2-NCO(-) system suggests that ferrate(V) is not directly participating in the oxidation of cyanate. Possible reactions in the system are presented to explain results of ferrate(VI) reduction and oxidation of cyanate.

Exposure to Sodium Dichromate at Qarmat Ali Iraq in 2003: Part 2 -- Evaluation of Army and Contractor Actions Related to Hazardous Industrial Exposure

Science.gov (United States)

2011-09-28

hexavalent chromium (chromium VI), a known carcinogen. USACE and the Army command in Iraq were made aware of the exposure in 2003 and took a series of...occupational and environmental health risks to U.S. personnel from potential exposure to hexavalent chromium [Cr(VI)] and other hazards prior to...chromium, or stigmata such as chrome ulcers. It was assumed by the 12 USACHPPM identified members of the West Virginia Army National Guard as part of the

Vi har intet lært - hvornår lærer vi det?

DEFF Research Database (Denmark)

Sodemann, Morten

2016-01-01

WHO anså fra i går ikke længere ebola for at være en trussel mod global folkesundhed, så fra i dag er kameraerne slukket i Vestafrika og vi er tilbage hvor vi startede. SDG målene skal have et dansk udtryk, men hvad er de danske kompetencer på globalt plan når sundhed ikke længere er en kerneakti......WHO anså fra i går ikke længere ebola for at være en trussel mod global folkesundhed, så fra i dag er kameraerne slukket i Vestafrika og vi er tilbage hvor vi startede. SDG målene skal have et dansk udtryk, men hvad er de danske kompetencer på globalt plan når sundhed ikke længere er en...

Effective Adsorption/Reduction of Cr(VI) Oxyanion by Halloysite@Polyaniline Hybrid Nanotubes.

Science.gov (United States)

Zhou, Tianzhu; Li, Cuiping; Jin, Huiling; Lian, Yangyang; Han, Wenmei

2017-02-22

Halloysite@polyaniline (HA@PANI) hybrid nanotubes are synthesized by the in situ chemical polymerization of aniline on halloysite clay nanotubes. By facilely tuning the dopant acid, pH, and apparent weight proportion for aniline (ANI) and halloysite (HA) nanotubes in the synthesis process, PANI with tuned oxidation state, doping extent, and content are in situ growing on halloysite nanotubes. The reaction system's acidity is tuned by dopant acid, such as HCl, H 2 SO 4 , HNO 3 , and H 3 PO 4 . The adsorption result shows the fabricated HA@PANI hybrid nanotubes can effectively adsorb Cr(VI) oxyanion and the adsorption ability changes according to the dopant acid, pH, and apparent weight proportion for ANI and HA in the synthesis process. Among them, the HA@PANI fabricated with HCl as dopant acid tuning the pH at 0.5 and 204% apparent weight proportion for ANI and HA (HP/0.5/204%-HCl) shows the highest adsorption capacity. The adsorption capacity is in accordance well with the doping extent of PANI in HA@PANI. Furthermore, when HP/0.5/204%-HCl is redoped with HNO 3 , H 2 SO 4 , and H 3 PO 4 , the adsorption capacity declines, implying the dopant acid in the process of redoping exhibits a marked effect on Cr(VI) oxyanion adsorption for the HA@PANI hybrid nanotubes. HP/0.5/204%-HCl and HP/0.5/204%-H 3 PO 4 have demonstrated good regenerability with an above 80% removal ratio after four cycles. Moreover, the HA@PANI adsorbent has better sedimentation ability than that of pure PANI. The adsorption behavior is in good agreement with Langmuir and pseudo second-order equations, indicating the adsorption of HA@PANI for Cr(VI) oxyanion is chemical adsorption. FT-IR and XPS of HA@PANI after Cr(VI) oxyanion adsorption indicate that the doped amine/imine groups (-NH + /═N + - groups) are the main adsorption sites for the removal of Cr(VI) oxyanion by electrostatic adsorption and reduction of the adsorbed Cr (VI) oxyanion to Cr(III) simultaneously.

A comparative analysis of five chrome green pigments based on different spectroscopic techniques

International Nuclear Information System (INIS)

Desnica, V.; Furic, K.; Hochleitner, B.; Mantler, M.

2003-01-01

A detailed study of five chrome-based green pigments belonging to a large pigment collection at the Academy of Fine Arts in Vienna, Austria has been performed. The samples were analyzed and compared using the two X-ray methods--X-ray fluorescence and X-ray diffraction, and the two optical methods--Raman spectroscopy and infrared spectroscopy. The composition differences between the similarly denoted samples of the collection were determined and the significant sensitivity differences of the investigated methods to specific compounds have been established. This relative discrepancy of the obtained results depending on the technique used proved once again the need of a combined use of the investigated methods

The Effect of the Concentration of Oxidant, Cr(VI), on the Iron Oxidation in Saline Water

Science.gov (United States)

Ahn, H.; Jo, H. Y.; Ryu, J. H.; Koh, Y. K.

2014-12-01

Deep geological disposal is currently considered as the most appropriate method to isolate high level radioactive wastes (HLRWs) from the ecosystem. If groundwater seeps into underground disposal facilities, water molecules can be dissociated to radicals or peroxides, which can oxidize metal canisters and HLRWs. The oxidized radionuclides with a high solubility can be dissolved in the groundwater. Some dissolved radionuclides can act as oxidants. The continuous radiolysis of water molecules, which results from continuous seepage of groundwater, can enable the continuous production of the radioactive oxidants, resulting in an increase in concentration of oxidants. In this study, the effect of oxidant concentration on iron oxidation in the presence of salt was evaluated. Zero valent iron (ZVI) particles were reacted with Cr(VI) solutions with initial Cr(VI) concentrations ranged from 50 to 300 mg/L in reactors. The initial pH and NaCl concentration were fixed at 3 and 0.5 M, respectively. An increase in the initial Cr(VI) concentration caused an increase in the rate and extend of H2 gas production. The decrement of Cr(VI) was increased as the initial Cr(VI) concentration was increased. The penetration of H+ ions in the presence Cl- ions through the passive film on the ZVI particles caused the reaction between H+ ions and ZVI particles, producing H2 gas and Fe2+ ions. The passive film was damaged during the reaction due to the eruption of H2 gas or peptization by Cl- ions. The Fe2+ ions were reacted with Cr(VI) ions in the solution, producing Fe(III)-Cr(III) (oxy)hydroxides on the passive film of ZVI particles or in the solution as colloidal particles. The Fe(III)-Cr(III) (oxy)hydroxides tends to be precipitated as colloidal particles at a high Cr(VI) concentration and precipitated on the passive film at a low Cr(VI) concentration. The passive film was repaired or thickened by additional formation of Fe(III)-Cr(III) (oxy)hydroxides at a lower Cr(VI) concentration.

Comparative EXAFS study of uranium(VI) and neptunium(V) sorption onto kaolinite

International Nuclear Information System (INIS)

Reich, T.; Amayri, S.; Reich, Ta.; Jermolajev, J.

2005-01-01

Full text of publication follows: We investigated the surface sorption process of U(VI) and Np(V) on kaolinite by extended X-ray absorption fine structure (EXAFS) spectroscopy in the 10 μM concentration range. Batch experiments with kaolinite in CO 2 -equilibrated systems showed that the adsorption edge of U(VI) occurs at pH 5.5, i.e., near the pH PZC of kaolinite. The adsorption edge of Np(V) occurs well above the pH PZC value at pH 8.5. This may indicate that the bonds between Np(V) and the surface functional groups of kaolinite are not as strong as in the case of U(VI). U(VI) and Np(V) have in common that the amount which is adsorbed decreases when the pH is increased beyond the absorption maximum. This behavior can be attributed to the formation of U(VI) and Np(V) carbonato complexes in the aqueous solutions. The aim of this comparative EXAFS study was to investigate the reason for the different affinities of U(VI) and Np(V) for kaolinite by measuring their local environments at the clay surface. Samples were prepared from 4 g/L kaolinite, 0.1 M NaClO 4 , pH 3.0 - 10.5, presence and absence of ambient CO 2 . The U L 3 - and Np L 2 -edge EXAFS spectra of the wet paste samples were measured at room temperature in fluorescence mode at the Rossendorf Beamline (ROBL) at the European Synchrotron Radiation Facility. The measured U-O and U-Al/Si distances indicate inner-sphere sorption of U(VI) on kaolinite. There was no evidence of uranium neighbors in the EXAFS spectra, suggesting that the adsorbed U(VI) complexes were predominantly monomeric. The average distance between uranium and its equatorial oxygen atoms, O eq , increased from 2.32 to 2.38 Angstrom in the presence of atmospheric CO 2 when the pH was increased from 5.0 to 8.5. In the CO 2 -free system, the U-O eq distance was independent from pH and equal to 2.32 Angstrom. The lengthening of the average U-O eq distance in the presence of carbonate (or bicarbonate) suggests the formation of ternary U(VI

C-N bond cleavage of anilines by a (salen)ruthenium(VI) nitrido complex.

Science.gov (United States)

Man, Wai-Lun; Xie, Jianhui; Pan, Yi; Lam, William W Y; Kwong, Hoi-Ki; Ip, Kwok-Wa; Yiu, Shek-Man; Lau, Kai-Chung; Lau, Tai-Chu

2013-04-17

We report experimental and computational studies of the facile oxidative C-N bond cleavage of anilines by a (salen)ruthenium(VI) nitrido complex. We provide evidence that the initial step involves nucleophilic attack of aniline at the nitrido ligand of the ruthenium complex, which is followed by proton and electron transfer to afford a (salen)ruthenium(II) diazonium intermediate. This intermediate then undergoes unimolecular decomposition to generate benzene and N2.

Effect of uranium (VI) on the growth of yeast and influence of metabolism of yeast on adsorption of U (VI)

International Nuclear Information System (INIS)

Sakamoto, Fuminori; Ohnuki, Toshihiko; Kozai, Naofumi; Wakai, Eiichi; Francis, A.J.

2005-01-01

We have carried out the growth experiments of 3 strains of yeast in a medium containing uranium (VI) to elucidate the effect of U (VI) on the growth of microorganisms. Hansenula fabianii J640 grew in the liquid medium containing 0.1 mM U (VI) at lower rate than the control, but Saccharomyces cerevisiae did not grow under this condition. The H. fabianii J640 pre-cultured for 21 h in the liquid medium without U (VI) grew even after the exposure to 1 mM U (VI), but did not grow without pre-cultivation. For the pre-cultured H. fabianii J640, radioactivity of U in the medium was the same as the initial one for 110 h, and then gradually decreased. TEM-EDS analysis of H. fabianii J640 exposed to 1 mM U (VI) for 165 h showed accumulation of U (VI) on the cells. When H. fabianii J640 was not pre-cultured, radioactivity of U in the medium was lower than the initial one. These results indicated that U (VI) inhibits the growth of yeast, and that the adsorption of U (VI) by the cells depends on the metabolism of yeast. (author)

Design and construction of a fast critical facility

International Nuclear Information System (INIS)

Kato, W.Y.; Dates, L.R.

1962-01-01

Design and construction of a fast critical facility. In a fast-power-reactor development programme, a critical facility is found to be a highly useful tool to ascertain calculational techniques, to verify neutron cross-section sets, and to obtain integral reactor-physics parameters necessary for the nuclear design of a power system. Since it is primarily a physics instrument, the design of a fast critical facility itself poses a number of different problems not found in the design of a power reactor. In addition to usual questions of site, containment, core design and instrumentation , there arise such problems as: how to obtain a large degree of flexibility consistent with safety, the determination of the size and type of facility to meet the experimental physics requirements, the determination of the number and location of control and safety rods minimizing perturbation effects and the specification of the reproducibility of control rods and other movable components to obtain the accuracy required in reactivity measurements. These are some of the problems which are discussed in this paper based on recent experience at the Argonne National Laboratory which has under construction a fast critical facility, ZPR-VI at its Lemont, Illinois site for fast-reactor-physics studies. The ZPR-VI is a movable half- or split-table-type machine similar to ZPR-III. It has a matrix about two and a half times the volume of the earlier machine and will be used to investigate the physics of large, highly dilute, metal and cermet, unmoderated and partially moderated systems having core volumes up to about 1500 l. A detailed description of the ZPR-VI with a discussion on the criteria used in the design of its various components from the point of view of reactor physics is presented. In addition, such topics as management and operating procedures, potential hazards during operation, experimental techniques to be used and construction costs are also included. (author) [fr

Preparation and properties of N-Phenylbutyrohydroxamic acid and N-p-Chlorophenylbutyrohydroxamic acid and their uses as extracting agents for Chromium (VI), Molybdenum (VI), Titanium (IV) and Uranium (VI)

Energy Technology Data Exchange (ETDEWEB)

Abu Elnour, Sawsan Hassan [Department of Chemistry, Faculty of Science, University of Khartoum, Khartoum (Sudan)

1993-05-01

Two lignads, N-phenylbutyrohydroxamic acid (1), N-p-chlorophenylbutyryl chloride with {beta} phenyl-hydroylamine and N-p-chlorophenylhydroxylamine, respectively. The acids prepared were identified and characterised through their reactions with Vanadiun (V) and iron (III), their melting points, infra-red spectra and nitrogen content. The extractive properties of these acids towards the metals Cr (VI), Mo (VI), Ti (IV) and U (VI) were examined at different PH values. The percentage of maximum extraction with the two acids was found to be as follows : for Cr (VI) at PH 1, (100%) for both acids, Mo (VI) at PH 2 (33.34%) with acid (I) and (16.67%) with acid (II) and U (VI) at PH 6 (72%) with acid (I) and (76%) with acid (II). The metal: Ligand complexes ratios were determined by using the continuous variation method, the ratio of the two ligands with four metals was found to be 1:2. Finally the suitability of the two acids for spectrophotometric determination of four metals was examined.(Author) 90 refs. , 24 tabs. , 24 figs

Preparation and properties of N-Phenylbutyrohydroxamic acid and N-p-Chlorophenylbutyrohydroxamic acid and their uses as extracting agents for Chromium (VI), Molybdenum (VI), Titanium (IV) and Uranium (VI)

International Nuclear Information System (INIS)

Abu Elnour, Sawsan Hassan

1993-05-01

Two lignads, N-phenylbutyrohydroxamic acid (1), N-p-chlorophenylbutyryl chloride with β phenyl-hydroylamine and N-p-chlorophenylhydroxylamine, respectively. The acids prepared were identified and characterised through their reactions with Vanadiun (V) and iron (III), their melting points, infra-red spectra and nitrogen content. The extractive properties of these acids towards the metals Cr (VI), Mo (VI), Ti (IV) and U (VI) were examined at different PH values. The percentage of maximum extraction with the two acids was found to be as follows : for Cr (VI) at PH 1, (100%) for both acids, Mo (VI) at PH 2 (33.34%) with acid (I) and (16.67%) with acid (II) and U (VI) at PH 6 (72%) with acid (I) and (76%) with acid (II). The metal: Ligand complexes ratios were determined by using the continuous variation method, the ratio of the two ligands with four metals was found to be 1:2. Finally the suitability of the two acids for spectrophotometric determination of four metals was examined.(Author)

154 Effet du chrome niacinate sur la tolérance au glucose chez le rat ...

African Journals Online (AJOL)

PR BOKO

contribution to the DEX treated groups. CrN supplementation did not correct the elevation of blood glucose ... chrome niacinate (30mg/kg/j, PO) pendant 14 jours, n=10. 2-2-2. Prélèvements. 1mL de sang a été prélevé à partir de la veine caudale sur tube hépariné à j0, j7, j14, j21 et j28. Les prélèvements ont été centrifugés ...

Elevated Frequencies of Micronuclei and other Nuclear Abnormalities of Chrome Plating Workers Occupationally Exposed to Hexavalent Chromium

OpenAIRE

Sudha, S; Kripa, SK; Shibily, P; Shyn, J

2011-01-01

Background Biomonitoring provides a useful tool to estimate the genetic risk from exposure to genotoxic agents. The aim of this study was to assess the potential cytogenetic damage associated with occupational exposure to hexavalent chromium by using micronuclei (MN) as a biomarker. Methods This was a cross-sectional study and all participants were males. Both the exposed and control individuals were selected from Coimbatore, Southern India. Exfoliated buccal cells from 44 chrome plating work...

ESR investigations of radiation grafting of methyl methacrylate in aqueous emulsion onto chrome-tanned pig skin

International Nuclear Information System (INIS)

Pietrucha, K.; Pekala, W.; Plonka, A.

1980-01-01

Upon γ-irradiation at 77 K of the aqueous emulsions of methyl methacrylate embedded into chrome-tanned pig skins there are formed only the radicals of collagen and of 2-el-2-methylopropionic acid methyl ester. The presence of water in the system increases markedly the radiation yield of collagen radicals. During gradual heating up the polymerization reactions start and the macro-radical of growing polymer is observed. Chromium does not participate in the processes of initiation and grafting. (author)

Hardening parts by chrome plating in manufacture and repair

Science.gov (United States)

Astanin, V. K.; Pukhov, E. V.; Stekolnikov, Y. A.; Emtsev, V. V.; Golikova, O. A.

2018-03-01

In the engineering industry, galvanic coatings are widely used to prolong the service life of the machines, which contribute to the increase in the strength of the parts and their resistance to environmental influences, temperature and pressure drops, wear and fretting corrosion. Galvanic coatings have been widely applied in engineering, including agriculture, aircraft building, mining, construction, and electronics. The article focuses on the manufacturing methods of new agricultural machinery parts and the repair techniques of worn parts by chrome plating. The main attention is paid to the unstable methods of chromium deposition (in pulsed and reversing modes) in low-concentration electrolytes, which makes it possible to increase the reliability and durability of the hardened parts operation by changing the conditions of electrocrystallization, that is, directed formation of the structure and texture, thickness, roughness and microhardness of chromium plating. The practical recommendations are given on the current and temperature regimes of chromium deposition and composition of baths used for the restoration and hardening of the machine parts. Moreover, the basic methods of machining allowances removal are analysed.

Comparative of the Tribological Performance of Hydraulic Cylinders Coated by the Process of Thermal Spray HVOF and Hard Chrome Plating

Directory of Open Access Journals (Sweden)

R.M. Castro

2014-03-01

Full Text Available Due to the necessity of obtaining a surface that is resistant to wear and oxidation, hydraulic cylinders are typically coated with hard chrome through the process of electroplating process. However, this type of coating shows an increase of the area to support sealing elements, which interferes directly in the lubrication of the rod, causing damage to the seal components and bringing oil leakage. Another disadvantage in using the electroplated hard chromium process is the presence of high level hexavalent chromium Cr+6 which is not only carcinogenic, but also extremely contaminating to the environment. Currently, the alternative process of high-speed thermal spraying (HVOF - High Velocity Oxy-Fuel, uses composite materials (metal-ceramic possessing low wear rates. Research has shown that some mechanical properties are changed positively with the thermal spray process in industrial applications. It is evident that a coating based on WC has upper characteristics as: wear resistance, low friction coefficient, with respect to hard chrome coatings. These characteristics were analyzed by optical microscopy, roughness measurements and wear test.

Kinetic model of the thermal pyrolysis of chrome tanned leather treated with NaOH under different conditions using thermogravimetric analysis.

Science.gov (United States)

Bañón, E; Marcilla, A; García, A N; Martínez, P; León, M

2016-02-01

The thermal decomposition of chrome tanned leather before and after a soaking treatment with NaOH was studied using thermogravimetric analysis (TGA). The effect of the solution concentration (0.2M and 0.5M) and the soaking time (5min and 15min) was evaluated. TGA experiments at four heating rates (5, 10, 15 and 20°Cmin(-1)) were run in a nitrogen atmosphere for every treatment condition. A kinetic model was developed considering the effect of the three variables studied, i.e.: the NaOH solution concentration, the soaking time and the heating rate. The proposed model for chrome tanned leather pyrolysis involves a set of four reactions, i.e.: three independent nth order reactions, yielding the corresponding products and one of them undergoing a successive cero order reaction. The model was successfully applied simultaneously to all the experimental data obtained. The evaluation of the kinetic parameters obtained (activation energy, pre-exponential factor and reaction order) allowed a better understanding of the effect of the alkali treatment on these wastes. Copyright © 2015 Elsevier Ltd. All rights reserved.

Preparation of Eco-Friendly Leather by Process Modifications to Make Pollution Free Tanneries

OpenAIRE

Mekonnen, Derese; Habtamu, Shewarega; Sathiyamoorthy, M; Selvi, V

2013-01-01

The term eco friendly leather meant the chrome free leather. Around 80% of leather is tanned using chromium. The chromium used in the tannery may be in the form of chromium III, IV and chromium VI compounds. The chromium tanned leathers use chromium III salts (Trivalent chromium) in the form of chromium sulfate. This form of chromium is found naturally in the environment and is necessary nutrient for the human body. However the chromium III oxidizes to chromium VI (Hexavalent chromium) in the...

Recycling of Chrome Tanned Leather Dust in Acrylonitrile Butadiene Rubber

Science.gov (United States)

El-Sabbagh, Salwa H.; Mohamed, Ola A.

2010-06-01

Concerns on environmental waste problem caused by chrome tanned leather wastes in huge amount have caused an increasing interest in developing this wastes in many composite formation. This leather dust was used as filler in acrylonitrile butadiene rubber (NBR) before treatment and after treatment with ammonia solution and sod. formate. Different formulations of NBR/ leather dust (untreated-treated with ammonia solution—treated with sod. formate) composites are prepared. The formed composite exhibit a considerable improvement in some of their properties such as rheometric characteristics especially with composites loaded with treated leather dust. Tensile strength, modulus at 100% elongation, hardness and youngs modulus were improved then by further loading start to be steady or decrease. Cross linking density in toluene were increased by incorporation of leather dust treated or untreated resulting in decreases in equilibrium swelling. Distinct increase in the ageing coefficient of both treated and untreated leather with drop in NBR vulcanizates without leather dust. Addition of leather dust treated or untreated exhibit better thermal stability.

The influence of activating agents on the performance of rice husk-based carbon for sodium lauryl sulfate and chrome (Cr) metal adsorptions

Science.gov (United States)

Arneli; Safitri, Z. F.; Pangestika, A. W.; Fauziah, F.; Wahyuningrum, V. N.; Astuti, Y.

2017-02-01

This research aims to study the influence of activating agents to produce rice husk based-carbon with high adsorption capacity and efficiency for either hazardous organic molecules or heavy metals which are unfriendly for the environment. Firstly, rice husk was burned by pyrolysis at different temperatures to produce rice husk-based carbon. To improve its ability as an adsorbent, carbon was treated with activating agents, namely, H3PO4 and KOH at room and high temperature (420 °C). The performance of carbon was then tested by contacting it with surfactant (SLS). Finally, the surfactant-modified active carbon was applied for chrome metal removal. The result shows that activation of carbon using phosphate acid (H3PO4) was more effective than potassium hydroxide (KOH) conducted at high temperature to adsorb sodium lauryl sulfate (SLS) and chrome metal with the adsorption capacity 1.50 mgg-1 and 0.375 mgg-1, respectively.

Zero-valent iron nanoparticles embedded into reduced graphene oxide-alginate beads for efficient chromium (VI) removal.

Science.gov (United States)

Lv, Xiaoshu; Zhang, Yuling; Fu, Wenyang; Cao, Jiazhen; Zhang, Jiao; Ma, Hanbo; Jiang, Guangming

2017-11-15

Zero-valent iron nanoparticles (Fe 0 NPs) technologies are often challenged by poor dispersibility, chemical instability to oxidation, and mobility during processing, storage and use. This work reports a facile approach to synthesize Fe 0 NPs embedded reduced graphene oxide-alginate beads (Fe@GA beads) via the immobilization of pre-synthesized Fe 0 NPs into graphene oxide modified alginate gel followed by a modelling and in-situ reduction process. The structure/composition characterization of the beads finds that the graphene sheets and the Fe 0 NPs (a shape of ellipsoid and a size of beads. We demonstrate that these Fe@GA beads show a robust performance in aqueous Cr(VI) removal. With a optimized Fe and alginate content, Fe@GA bead can achieve a high Cr(VI) removal efficiency and an excellent mechanical strength. The initial Cr(VI) concentration, ionic strength, temperature and especially solution pH are all critical factors to control the Fe@GA beads performance in Cr(VI) removal. Fitness of the pseudo second-order adsorption model with data suggests adsorption is the rate-controlling step, and both Langmuir and Freundlich adsorption isotherm are suitable to describe the removal behavior. The possible Cr(VI) removal path by Fe@GA beads is put forward, and the synergistic effect in this ternary system implies the potentials of Fe@GA beads in pollutant removal from water body. Copyright © 2017 Elsevier Inc. All rights reserved.

Different roles of ROS and Nrf2 in Cr(VI)-induced inflammatory responses in normal and Cr(VI)-transformed cells

Energy Technology Data Exchange (ETDEWEB)

Roy, Ram Vinod; Pratheeshkumar, Poyil; Son, Yong-Ok; Wang, Lei [Center for Research on Environmental Disease, University of Kentucky, 1095 VA Drive, Lexington, KY 40536 (United States); Department of Toxicology and Cancer Biology, College of Medicine, University of Kentucky, 1095 VA Drive, Lexington, KY 40536 (United States); Hitron, John Andrew [Center for Research on Environmental Disease, University of Kentucky, 1095 VA Drive, Lexington, KY 40536 (United States); Divya, Sasidharan Padmaja; Zhang, Zhuo [Department of Toxicology and Cancer Biology, College of Medicine, University of Kentucky, 1095 VA Drive, Lexington, KY 40536 (United States); Shi, Xianglin, E-mail: xshi5@email.uky.edu [Center for Research on Environmental Disease, University of Kentucky, 1095 VA Drive, Lexington, KY 40536 (United States)

2016-09-15

Hexavalent chromium (Cr(VI)) is classified as a human carcinogen. Cr(VI) has been associated with adenocarcinomas and squamous cell carcinoma of the lung. The present study shows that acute Cr(VI) treatment in human bronchial epithelial cells (BEAS-2B) increased inflammatory responses (TNF-α, COX-2, and NF-кB/p65) and expression of Nrf2. Cr(VI)-induced generation of reactive oxygen species (ROS) are responsible for increased inflammation. Despite the fact that Nrf2 is a master regulator of response to oxidative stress, silencing of Nrf2 in the acute Cr(VI) treatment had no effect on Cr(VI)-induced inflammation. In contrast, in Cr(VI)-transformed (CrT) cells, Nrf2 is constitutively activated. Knock-down of this protein resulted in decreased inflammation, while silencing of SOD2 and CAT had no effect in the expression of these inflammatory proteins. Results obtained from the knock-down of Nrf2 in CrT cells are very different from the results obtained in the acute Cr(VI) treatment. In BEAS-2B cells, knock-down of Nrf2 had no effect in the inflammation levels, while in CrT cells a decrease in the expression of inflammation markers was observed. These results indicate that before transformation, ROS plays a critical role while Nrf2 not in Cr(VI)-induced inflammation, whereas after transformation (CrT cells), Nrf2 is constitutively activated and this protein maintains inflammation while ROS not. Constitutively high levels of Nrf2 in CrT binds to the promoter regions of COX-2 and TNF-α, leading to increased inflammation. Collectively, our results demonstrate that before cell transformation ROS are important in Cr(VI)-induced inflammation and after transformation a constitutively high level of Nrf2 is important. - Highlights: • Cr(VI)-induced ROS increased inflammation, while Nrf2 had no effect. • In the CrT cells knock-down of Nrf2 resulted in decreased inflammation. • Mechanistic differences in regulating Cr(VI)-induced inflammation.

Paul Scherrer Institute Scientific and Technical Report 2000. Volume VI: Large Research Facilities

International Nuclear Information System (INIS)

Foroughi, Fereydoun; Bercher, Renate; Buechli, Carmen; Zumkeller, Lotty

2001-01-01

The PSI Department Large Research Facilities (GFA) joins the efforts to provide an excellent research environment to Swiss and foreign research groups on the experimental facilities driven by our high intensity proton accelerator complex. Its divisions care for the running, maintenance and enhancement of the accelerator complex, the primary proton beamlines, the targets and the secondary beams as well as the neutron spallation source SINQ. The division for technical support and coordination provides for technical support to the research facility complementary to the basic logistic available from the department for logistics and marketing. Besides running the facilities, the staff of the department is also involved in theoretical and experimental research projects. Some of them address basic scientific questions mainly concerning the properties of micro- or nanostructured materials: experiments as well as large scale computer simulations of molecular dynamics were performed to investigate nonclassical materials properties. Others are related to improvements or extensions of the capabilities of our facilities. We also report on intriguing results from applications of the neutron capture radiography, the prompt gamma activation method and the isotope production facility at SINQ

Paul Scherrer Institute Scientific and Technical Report 2000. Volume VI: Large Research Facilities

Energy Technology Data Exchange (ETDEWEB)

Foroughi, Fereydoun; Bercher, Renate; Buechli, Carmen; Zumkeller, Lotty [eds.

2001-07-01

The PSI Department Large Research Facilities (GFA) joins the efforts to provide an excellent research environment to Swiss and foreign research groups on the experimental facilities driven by our high intensity proton accelerator complex. Its divisions care for the running, maintenance and enhancement of the accelerator complex, the primary proton beamlines, the targets and the secondary beams as well as the neutron spallation source SINQ. The division for technical support and coordination provides for technical support to the research facility complementary to the basic logistic available from the department for logistics and marketing. Besides running the facilities, the staff of the department is also involved in theoretical and experimental research projects. Some of them address basic scientific questions mainly concerning the properties of micro- or nanostructured materials: experiments as well as large scale computer simulations of molecular dynamics were performed to investigate nonclassical materials properties. Others are related to improvements or extensions of the capabilities of our facilities. We also report on intriguing results from applications of the neutron capture radiography, the prompt gamma activation method and the isotope production facility at SINQ.

Recursos de información elaborados por el CRAI. Instalar y Configurar Zotero enlazarlo a Mozilla, Chrome y Word

OpenAIRE

López Lucas, Jesús

2018-01-01

Este tutorial explica los pasos para la instalación del gestor de referencias bibliográficas Zotero en un PC con Sistema Operativo Microsoft Windows. Asimismo, se indican las características del software y la manera de trabajar con él desde Mozilla Firefox, Google Chrome y Microsoft Word. Tutorial sobre instalación y configuración de Zotero para los diferentes navegadores web.

Kinetic investigations of quinoline oxidation by ferrate(VI).

Science.gov (United States)

Luo, Zhiyong; Li, Xueming; Zhai, Jun

2016-01-01

Quinoline is considered as one of the most toxic and carcinogenic compounds and is commonly found in industrial wastewaters, which require treatment before being discharged. Removal of quinoline by the use of an environmentally friendly oxidant, potassium ferrate(VI) (K2FeO4), was assessed by studying the kinetics of the oxidation of quinoline by ferrate(VI) (Fe(VI)) as a function of pH (8.53-10.53) and temperature (21-36°C) in this work. The reaction of quinoline with Fe(VI) was found to be first order in Fe(VI), half order in quinoline, and 1.5 order overall. The observed rate constant at 28°C decreased non-linearly from 0.5334 to 0.2365 M(-0.5) min(-1) with an increase in pH from 8.53 to 10.03. Considering the equilibria of Fe(VI) and quinoline, the reaction between quinoline and Fe(VI) contained two parallel reactions under the given pH conditions. The individual rate constants of these two reactions were determined. The results indicate that the protonated species of Fe(VI) reacts more quickly with quinoline than the deprotonated form of Fe(VI). The reaction activation energy Ea was obtained to be 51.44 kJ·mol(-1), and it was slightly lower than that of conventional chemical reaction. It reveals that the oxidation of quinoline by Fe(VI) is feasible in the routine water treatment.

47 CFR 2.948 - Description of measurement facilities.

Science.gov (United States)

2010-10-01

... description of the measurement facilities employed. (1) If the measured equipment is subject to the... number; (v) FCC Registration Number (FRN); (vi) A statement as to whether or not the laboratory performs... supporting structures, and all structures within 5 times the distance between the measuring antenna and the...

Immunization with the conjugate vaccine Vi-CRM₁₉₇ against Salmonella typhi induces Vi-specific mucosal and systemic immune responses in mice.

Science.gov (United States)

Fiorino, Fabio; Ciabattini, Annalisa; Rondini, Simona; Pozzi, Gianni; Martin, Laura B; Medaglini, Donata

2012-09-21

Typhoid fever is a public health problem, especially among young children in developing countries. To address this need, a glycoconjugate vaccine Vi-CRM₁₉₇, composed of the polysaccharide antigen Vi covalently conjugated to the non-toxic mutant of diphtheria toxin CRM₁₉₇, is under development. Here, we assessed the antibody and cellular responses, both local and systemic, following subcutaneous injection of Vi-CRM₁₉₇. The glycoconjugate elicited Vi-specific serum IgG titers significantly higher than unconjugated Vi, with prevalence of IgG1 that persisted for at least 60 days after immunization. Vi-specific IgG, but not IgA, were present in intestinal washes. Lymphocytes proliferation after restimulation with Vi-CRM₁₉₇ was observed in spleen and mesenteric lymph nodes. These data confirm the immunogenicity of Vi-CRM₁₉₇ and demonstrate that the vaccine-specific antibody and cellular immune responses are present also in the intestinal tract, thus strengthening the suitability of Vi-CRM₁₉₇ as a promising candidate vaccine against Salmonella Typhi. Copyright © 2012 Elsevier Ltd. All rights reserved.

33 CFR 106.305 - Facility Security Assessment (FSA) requirements.

Science.gov (United States)

2010-07-01

... available to maintain essential services; (vi) The essential maintenance equipment and storage areas; (vii... procedures relating to essential services; (v) Measures to protect radio and telecommunication equipment... property, or economic disruption, of an attack on or at the OCS facility; and (7) Locations where access...

Electrochemical alkaline Fe(VI) water purification and remediation.

Science.gov (United States)

Licht, Stuart; Yu, Xingwen

2005-10-15

Fe(VI) is an unusual and strongly oxidizing form of iron, which provides a potentially less hazardous water-purifying agent than chlorine. A novel on-line electrochemical Fe(VI) water purification methodology is introduced. Fe(VI) addition had been a barrier to its effective use in water remediation, because solid Fe(VI) salts require complex (costly) syntheses steps and solutions of Fe(VI) decompose. Online electrochemical Fe(VI) water purification avoids these limitations, in which Fe(VI) is directly prepared in solution from an iron anode as the FeO42- ion, and is added to the contaminant stream. Added FeO42- decomposes, by oxidizing a wide range of water contaminants including sulfides (demonstrated in this study) and other sulfur-containing compounds, cyanides (demonstrated in this study), arsenic (demonstrated in this study), ammonia and other nitrogen-containing compounds (previously demonstrated), a wide range of organics (phenol demonstrated in this study), algae, and viruses (each previously demonstrated).

Electronic structure, fluorescence and photochemistry of the uranyl ion, and comparison with octahedral uranium (VI), ruthenyl (VI), rhenium (V) and osmium (VI) complexes

Energy Technology Data Exchange (ETDEWEB)

Joergensen, C K [Geneva Univ. (Switzerland)

1977-01-01

The highly anisotropic uranyl complexes (with very short U-O distances and very long distances to the ligating atoms in the equatorial plane) are compared with trans-dioxo complexes of 4d/sup 2/Ru(VI) and 5d/sup 2/Re(V) and Os(VI). A major difference is the low-lying empty 5f orbitals, and the first excited state is highly oxidizing, and sufficiently long-lived to abstract hydrogen atoms from most organic molecules. It is argued that even the low concentrations of uranyl carbonate present in sea water is excited by solar radiation roughly every 10 minutes. Octahedral U(VI)O/sub 6/ in perovskites and UF/sub 6/ are also discussed, as well as trans-lawrencium chemistry.

A review of the chrome mordant dyeing of wool with special reference to the afterchrome process

CSIR Research Space (South Africa)

Maasdorp, APB

1983-11-01

Full Text Available a -~min*o'- Hydroxyaw Dycs Salicylic Acid Dyes Azo dyes oxidkd to Quinone form when complexed (C.I. Mordant Black 3) e Chrome Fast Brow TV (C.I. Mordant Brow 33) Flavine A (C.I. Mordant Yellow 5) e Solochrome Rcd (C.I. Mordant..., it was decided that they should bedescribed in more detail. In 1858, Peter Greiss, a chemist at a Burton-on-Trent brewery produced the first diizonium salts by treating primary aromatic amines with nitrous acid produced from hydrochloric acid and sodium...

Biosorption of Cr(VI) by coconut coir: Spectroscopic investigation on the reaction mechanism of Cr(VI) with lignocellulosic material

International Nuclear Information System (INIS)

Shen, Ying-Shuian; Wang, Shan-Li; Huang, Shiuh-Tsuen; Tzou, Yu-Min; Huang, Jang-Hung

2010-01-01

In this study, the removal mechanism of Cr(VI) from water by coconut coir (CC) was investigated using X-ray photoelectron spectroscopy (XPS), Cr K-edge X-ray absorption near edge structure (XANES) and FTIR spectroscopy. The results showed that, upon reaction with CC at pH 3, Cr(VI) was reduced to Cr(III), which was either bound to CC or released back into solution. As revealed by the FTIR spectra of CC before and after reacting with Cr(VI), the phenolic methoxyl and hydroxyl groups of lignin in CC are the dominant drivers of Cr(VI) reduction, giving rise to carbonyl and carboxyl groups on CC. These functional groups can subsequently provide binding sites for Cr(III) resulting from Cr(VI) reduction. In conjunction with forming complexes with carbonyl and carboxyl groups, the formation of Cr(III) hydroxide precipitate could also readily occur as revealed by the linear combination fitting of the Cr K-edge XANES spectrum using a set of reference compounds. The phenolic groups in lignin are responsible for initiating Cr(VI) reduction, so lignocellulosic materials containing a higher amount of phenolic groups are expected to be more effective scavengers for removal of Cr(VI) from the environment.

Biosorption of Cr(VI) by coconut coir: Spectroscopic investigation on the reaction mechanism of Cr(VI) with lignocellulosic material

Energy Technology Data Exchange (ETDEWEB)

Shen, Ying-Shuian [Department of Soil and Environmental Sciences, National Chung Hsing University, 250 Kuo Kuang Road, Taichung 40227, Taiwan (China); Wang, Shan-Li, E-mail: slwang@nchu.edu.tw [Department of Soil and Environmental Sciences, National Chung Hsing University, 250 Kuo Kuang Road, Taichung 40227, Taiwan (China); Huang, Shiuh-Tsuen [Department of Soil and Environmental Sciences, National Chung Hsing University, 250 Kuo Kuang Road, Taichung 40227, Taiwan (China); Department of Science Application and Dissemination, National Taichung University, Taichung, Taiwan (China); Tzou, Yu-Min; Huang, Jang-Hung [Department of Soil and Environmental Sciences, National Chung Hsing University, 250 Kuo Kuang Road, Taichung 40227, Taiwan (China)

2010-07-15

In this study, the removal mechanism of Cr(VI) from water by coconut coir (CC) was investigated using X-ray photoelectron spectroscopy (XPS), Cr K-edge X-ray absorption near edge structure (XANES) and FTIR spectroscopy. The results showed that, upon reaction with CC at pH 3, Cr(VI) was reduced to Cr(III), which was either bound to CC or released back into solution. As revealed by the FTIR spectra of CC before and after reacting with Cr(VI), the phenolic methoxyl and hydroxyl groups of lignin in CC are the dominant drivers of Cr(VI) reduction, giving rise to carbonyl and carboxyl groups on CC. These functional groups can subsequently provide binding sites for Cr(III) resulting from Cr(VI) reduction. In conjunction with forming complexes with carbonyl and carboxyl groups, the formation of Cr(III) hydroxide precipitate could also readily occur as revealed by the linear combination fitting of the Cr K-edge XANES spectrum using a set of reference compounds. The phenolic groups in lignin are responsible for initiating Cr(VI) reduction, so lignocellulosic materials containing a higher amount of phenolic groups are expected to be more effective scavengers for removal of Cr(VI) from the environment.

Biosorption of Cr(VI) by coconut coir: spectroscopic investigation on the reaction mechanism of Cr(VI) with lignocellulosic material.

Science.gov (United States)

Shen, Ying-Shuian; Wang, Shan-Li; Huang, Shiuh-Tsuen; Tzou, Yu-Min; Huang, Jang-Hung

2010-07-15

In this study, the removal mechanism of Cr(VI) from water by coconut coir (CC) was investigated using X-ray photoelectron spectroscopy (XPS), Cr K-edge X-ray absorption near edge structure (XANES) and FTIR spectroscopy. The results showed that, upon reaction with CC at pH 3, Cr(VI) was reduced to Cr(III), which was either bound to CC or released back into solution. As revealed by the FTIR spectra of CC before and after reacting with Cr(VI), the phenolic methoxyl and hydroxyl groups of lignin in CC are the dominant drivers of Cr(VI) reduction, giving rise to carbonyl and carboxyl groups on CC. These functional groups can subsequently provide binding sites for Cr(III) resulting from Cr(VI) reduction. In conjunction with forming complexes with carbonyl and carboxyl groups, the formation of Cr(III) hydroxide precipitate could also readily occur as revealed by the linear combination fitting of the Cr K-edge XANES spectrum using a set of reference compounds. The phenolic groups in lignin are responsible for initiating Cr(VI) reduction, so lignocellulosic materials containing a higher amount of phenolic groups are expected to be more effective scavengers for removal of Cr(VI) from the environment. 2010 Elsevier B.V. All rights reserved.

Isolation of a star-shaped uranium(V/VI) cluster from the anaerobic photochemical reduction of uranyl(VI)

International Nuclear Information System (INIS)

Chatelain, Lucile; White, Sarah; Scopelliti, Rosario; Mazzanti, Marinella

2016-01-01

Actinide oxo clusters are an important class of compounds due to their impact on actinide migration in the environment. The photolytic reduction of uranyl(VI) has potential application in catalysis and spent nuclear fuel reprocessing, but the intermediate species involved in this reduction have not yet been elucidated. Here we show that the photolysis of partially hydrated uranyl(VI) in anaerobic conditions leads to the reduction of uranyl(VI), and to the incorporation of the resulting U V species into the stable mixed-valent star-shaped U VI /U V oxo cluster [U(UO 2 ) 5 (μ 3 -O) 5 (PhCOO) 5 (Py) 7 ]. This cluster is only the second example of a U VI /U V cluster and the first one associating uranyl groups to a non-uranyl(V) center. The U V center in 1 is stable, while the reaction of uranyl(V) iodide with potassium benzoate leads to immediate disproportionation and formation of the U 12 IV U 4 V O 24 cluster {[K(Py) 2 ] 2 [K(Py)] 2 [U 16 O 24 (PhCOO) 24 (Py) 2 ]}.

Comparison of U(VI) adsorption onto nanoscale zero-valent iron and red soil in the presence of U(VI)–CO_3/Ca–U(VI)–CO_3 complexes

International Nuclear Information System (INIS)

Zhang, Zhibin; Liu, Jun; Cao, Xiaohong; Luo, Xuanping; Hua, Rong; Liu, Yan; Yu, Xiaofeng; He, Likai

2015-01-01

Highlights: • NZVI can be used for adsorbing U(VI)–CO_3 complexes. • Use of NZVI is feasible for remediation of uranium-contaminated soils. • The mechanism of U(VI)–CO_3 complexes adsorbing onto NZVI has been explained. - Abstract: The influence of U(VI)–CO_3 and Ca–U(VI)–CO_3 complexes on U(VI) adsorption onto red soil and nanoscale zero-valent iron (NZVI) was investigated using batch adsorption and fixed-bed column experiments to simulate the feasibility of NZVI as the reactive medium in permeable- reactive barriers (PRB) for in situ remediation of uranium-contaminated red soils. The adsorption capacity (q_e) and distribution constant (K_d) of NZVI and red soil decreased with increasing pH, dissolved carbonate and calcium concentrations, but the q_e and K_d values of NZVI were 5–10 times higher than those of red soil. The breakthrough pore volume (PV) values increased with the decrease of pH, dissolved carbonate and calcium concentration; however, the breakthrough PV values of the PRB column filled with 5% NZVI were 2.0–3.5 times higher than the 100% red soil column. The U(VI)–CO_3 complexes adsorbed onto the surface of red soil/NZVI (≡SOH) to form SO–UO_2CO_3"− or SO–UO_2 (CO_3)_2"3"−. XPS and XRD analysis further confirmed the reduction of U(VI) to U(IV) and the formation of FeOOH on NZVI surfaces. The findings of this study are significant to the remediation of uranium-contaminated red soils and the consideration of practical U(VI) species in the natural environment.

Monitoring the intensity of mechanical vibration during the processing of chrome steel 14109

Directory of Open Access Journals (Sweden)

Š. Salokyová

2017-01-01

Full Text Available Article deals with the examination of the effect of cutting parameters on the occurrence and size of mechanical vibration on three selected measured points during the processing of chrome steel. It also includes execution, experiment evaluation in this field and comparison of measured vibrations acceleration amplitude values according to the standards. The results of the measurement serve for early identification of a defect, which has great effect on the smoothness and efficiency of the machine. The article concludes with the proposed new findings from the measured values evaluation and formulated new recommendations for the operation in production system with lathe turning technology. The measured experimental values of the acceleration amplitude of mechanical vibrations were compared with theoretical values.

In Situ Bioreduction of Uranium (VI) to Submicromolar Levels and Reoxidation by Dissolved Oxygen

International Nuclear Information System (INIS)

Wu, Weimin; Carley, Jack M.; Luo, Jian; Ginder-Vogel, Matthew A.; Cardenas, Erick; Leigh, Mary Beth; Hwang, Chaichi; Kelly, Shelly D.; Ruan, Chuanmin; Wu, Liyou; Van Nostrand, Joy; Gentry, Terry J.; Lowe, Kenneth Alan; Mehlhorn, Tonia L.; Carroll, Sue L.; Luo, Wensui; Fields, Matthew Wayne; Gu, Baohua; Watson, David B.; Kemner, Kenneth M.; Marsh, Terence; Tiedje, James; Zhou, Jizhong; Fendorf, Scott; Kitanidis, Peter K.; Jardine, Philip M.; Criddle, Craig

2007-01-01

Groundwater within Area 3 of the U.S. Department of Energy (DOE) Environmental Remediation Sciences Program (ERSP) Field Research Center at Oak Ridge, TN (ORFRC) contains up to 135 (micro)M uranium as U(VI). Through a series of experiments at a pilot scale test facility, we explored the lower limits of groundwater U(VI) that can be achieved by in-situ biostimulation and the effects of dissolved oxygen on immobilized uranium. Weekly 2 day additions of ethanol over a 2-year period stimulated growth of denitrifying, Fe(III)-reducing, and sulfate-reducing bacteria, and immobilization of uranium as U(IV), with dissolved uranium concentrations decreasing to low levels. Following sulfite addition to remove dissolved oxygen, aqueous U(VI) concentrations fell below the U.S. Environmental Protection Agency maximum contaminant limit (MCL) for drinking water ( -1 or 0.126 (micro)M). Under anaerobic conditions, these low concentrations were stable, even in the absence of added ethanol. However, when sulfite additions stopped, and dissolved oxygen (4.0-5.5 mg L -1 ) entered the injection well, spatially variable changes in aqueous U(VI) occurred over a 60 day period, with concentrations increasing rapidly from <0.13 to 2.0 (micro)M at a multilevel sampling (MLS) well located close to the injection well, but changing little at an MLS well located further away. Resumption of ethanol addition restored reduction of Fe(III), sulfate, and U(VI) within 36 h. After 2 years of ethanol addition, X-ray absorption near-edge structure spectroscopy (XANES) analyses indicated that U(IV) comprised 60-80% of the total uranium in sediment samples. At the completion of the project (day 1260), U concentrations in MLS wells were less than 0.1 (micro)M. The microbial community at MLS wells with low U(VI) contained bacteria that are known to reduce uranium, including Desulfovibrio spp. and Geobacter spp., in both sediment and groundwater. The dominant Fe(III)-reducing species were Geothrix spp

The electrochemical aspect of the corrosion of austenitic stainless steels, in nitric acid and in the presence of hexavalent chromium (1961); Aspect electrochimique de la corrosion d'aciers inoxydables austenitiques en milieu nitrique et en presence de chrome hexavalent (1961)

Energy Technology Data Exchange (ETDEWEB)

Coriou, H.; Hure, J.; Plante, G. [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1961-07-01

The corrosion of austenitic stainless steels in boiling nitric acid markedly increases when the medium contains hexavalent chromium ions. Because of several redox phenomena, the potential of the steel generally changes in course of time. Measurements show a relation between the weight loss and the potential of specimens. Additions of Mn(VII) and Ce(IV) are compared with that of Cr(VI), and show that the relation is a general one. The attack cf the metal in oxidizing media is largely intergranular, leading to exfoliation of the grains, although the steel studied is not sensitive to the classical Huey and Strauss tests. Also even in the absence of any other oxidizing reaction, the current density observed when the steel is anodically polarized under potentiostatic conditions does not correspond to the actual weight loss of the metal. (authors) [French] La corrosion d'aciers inoxydables austenitiques en milieu nitrique bouillant augmente notablement quand le milieu contient des ions chrome a l'etat hexavalent. Par suite de divers phenomenes d'oxydo-reduction, le potentiel de l'acier evolue generalement au cours du temps. Les mesures effectuees permettent d'etablir une relation entre les pertes de poids et le potentiel des echantillons. L'addition de Mn(VI) et Ce(IV) est compare a celle de Cr(VI) et montre que la relation precedente s'applique de facon generale. L'attaque du metal en milieu oxydant est en grande, partie due a une corrosion intergranulaire conduisant a un dechaussement des grains bien que l'acier etudie ne soit pas sensible aux tests classiques de Huey et de Strauss. Aussi, meme en l'absence de toute autre reaction d'oxydation l'intensite qu l'on observerait en soumettant l'acier a un potentiel anodique dans un montage potentiostatique ne correspondrait pas a la perte de poids reelle du metal. (auteurs)

Reactivity of nitrido complexes of ruthenium(VI), osmium(VI), and manganese(V) bearing Schiff base and simple anionic ligands.

Science.gov (United States)

Man, Wai-Lun; Lam, William W Y; Lau, Tai-Chu

2014-02-18

Nitrido complexes (M≡N) may be key intermediates in chemical and biological nitrogen fixation and serve as useful reagents for nitrogenation of organic compounds. Osmium(VI) nitrido complexes bearing 2,2':6',2″-terpyridine (terpy), 2,2'-bipyridine (bpy), or hydrotris(1-pyrazolyl)borate anion (Tp) ligands are highly electrophilic: they can react with a variety of nucleophiles to generate novel osmium(IV)/(V) complexes. This Account describes our recent results studying the reactivity of nitridocomplexes of ruthenium(VI), osmium(VI), and manganese(V) that bear Schiff bases and other simple anionic ligands. We demonstrate that these nitrido complexes exhibit rich chemical reactivity. They react with various nucleophiles, activate C-H bonds, undergo N···N coupling, catalyze the oxidation of organic compounds, and show anticancer activities. Ruthenium(VI) nitrido complexes bearing Schiff base ligands, such as [Ru(VI)(N)(salchda)(CH3OH)](+) (salchda = N,N'-bis(salicylidene)o-cyclohexyldiamine dianion), are highly electrophilic. This complex reacts readily at ambient conditions with a variety of nucleophiles at rates that are much faster than similar reactions using Os(VI)≡N. This complex also carries out unique reactions, including the direct aziridination of alkenes, C-H bond activation of alkanes and C-N bond cleavage of anilines. The addition of ligands such as pyridine can enhance the reactivity of [Ru(VI)(N)(salchda)(CH3OH)](+). Therefore researchers can tune the reactivity of Ru≡N by adding a ligand L trans to nitride: L-Ru≡N. Moreover, the addition of various nucleophiles (Nu) to Ru(VI)≡N initially generate the ruthenium(IV) imido species Ru(IV)-N(Nu), a new class of hydrogen-atom transfer (HAT) reagents. Nucleophiles also readily add to coordinated Schiff base ligands in Os(VI)≡N and Ru(VI)≡N complexes. These additions are often stereospecific, suggesting that the nitrido ligand has a directing effect on the incoming nucleophile. M≡N is also

Mechanisms of chromium (VI)-induced apoptosis in anterior pituitary cells.

Science.gov (United States)

Quinteros, Fernanda A; Machiavelli, Leticia I; Miler, Eliana A; Cabilla, Jimena P; Duvilanski, Beatriz H

2008-07-30

Hexavalent chromium (Cr (VI)) is a highly toxic metal. Exposure to Cr (VI) compounds may affect reproductive functions. Due to the importance of anterior pituitary hormones on reproductive physiology we have studied the effects of Cr (VI) on anterior pituitary. We previously demonstrated that, after in vivo Cr (VI) administration, Cr accumulates in the pituitary gland and affects prolactin secretion. In vitro, Cr (VI) causes apoptosis in anterior pituitary cells due to oxidative stress generation. To better understand the mechanisms involved in Cr (VI)-induced apoptosis we studied: (a) whether Cr (VI) affects the intracellular antioxidant response and (b) which of the apoptotic factors participates in Cr (VI) effect. Our results show that Cr (VI) treatment induces a decrease in catalase and glutathione peroxidase (GPx) activity but does not modify glutathione reductase (GR) activity. Cr (VI) exposure causes an increase of GSH levels. p53 and Bax mRNA are also upregulated by the metal. Pifithrin alpha, a p53 transcriptional inhibitor, increases Cr (VI) cytotoxicity, suggesting a role of p53 as a survival molecule. The antioxidant N-acetyl-cysteine (NAC) could prevent Bax mRNA increase and caspase 3 activation, confirming that Cr (VI)-induced apoptosis involves oxidative stress generation.

Virtual neutron scattering experiments - Training and preparing students for large-scale facility experiments

Directory of Open Access Journals (Sweden)

Julie Hougaard Overgaard

2016-11-01

Full Text Available Dansk Vi beskriver, hvordan virtuelle eksperimenter kan udnyttes i et læringsdesign ved at forberede de studerende til hands-on-eksperimenter ved storskalafaciliteter. Vi illustrerer designet ved at vise, hvordan virtuelle eksperimenter bruges på Niels Bohr Institutets kandidatkursus om neutronspredning. I den sidste uge af kurset, rejser studerende til et storskala neutronspredningsfacilitet for at udføre neutronspredningseksperimenter. Vi bruger studerendes udsagn om deres oplevelser til at argumentere for, at arbejdet med virtuelle experimenter forbereder de studerende til at engagere sig mere frugtbart med eksperimenter ved at lade dem fokusere på fysikken og relevante data i stedet for instrumenternes funktion. Vi hævder, at det er, fordi de kan overføre deres erfaringer med virtuelle eksperimenter til rigtige eksperimenter. Vi finder dog, at læring stadig er situeret i den forstand, at kun kendskab til bestemte eksperimenter overføres. Vi afslutter med at diskutere de muligheder, som virtuelle eksperimenter giver. English We describe how virtual experiments can be utilized in a learning design that prepares students for hands-on experiments at large-scale facilities. We illustrate the design by showing how virtual experiments are used at the Niels Bohr Institute in a master level course on neutron scattering. In the last week of the course, students travel to a large-scale neutron scattering facility to perform real neutron scattering experiments. Through student interviews and survey answers, we argue, that the virtual training prepares the students to engage more fruitfully with experiments by letting them focus on physics and data rather than the overwhelming instrumentation. We argue that this is because they can transfer their virtual experimental experience to the real-life situation. However, we also find that learning is still situated in the sense that only knowledge of particular experiments is transferred. We proceed to

Emissions of chromium (VI) from arc welding.

Science.gov (United States)

Heung, William; Yun, Myoung-Jin; Chang, Daniel P Y; Green, Peter G; Halm, Chris

2007-02-01

The presence of Cr in the +6 oxidation state (Cr[VI]) is still observed in ambient air samples in California despite steps taken to reduce emissions from plating operations. One known source of emission of Cr(VI) is welding, especially with high Cr-content materials, such as stainless steels. An experimental effort was undertaken to expand and update Cr(VI) emission factors by conducting tests on four types of arc-welding operations: gas-metal arc welding (GMAW), shielded metal arc welding (SMAW), fluxcore arc welding, and pulsed GMAW. Standard American Welding Society hood results were compared with a total enclosure method that permitted isokinetic sampling for particle size-cut measurement, as well as total collection of the aerosol. The fraction of Cr(VI) emitted per unit mass of Cr electrode consumed was determined. Consistent with AP-42 data, initial results indicate that a significant fraction of the total Cr in the aerosol is in the +6 oxidation state. The fraction of Cr(VI) and total aerosol mass produced by the different arc welding methods varies with the type of welding process used. Self-shielded electrodes that do not use a shield gas, for example, SMAW, produce greater amounts of Cr(VI) per unit mass of electrode consumed. The formation of Cr(VI) from standard electrode wires used for welding mild steel was below the method detection limit after eliminating an artifact in the analytical method used.

Selection and application of C18200 chrome copper for the OHTE confinement test helical coil

International Nuclear Information System (INIS)

Puhn, F.A.; Graumann, D.W.

1981-01-01

The selection and qualification of copper for the OHTE confinement test helical coil (H-coil) was a crucial step in the success of this new experiment. Previous problems encountered at General Atomic Company with close tolerance machined parts made from high strength copper were identified. The design criteria included selecting a material with minimal warpage during machining, an electrical conductivity >80% IACS, and a yield strength of at least 241 Mpa (35 ksi). The investigation of candidate materials and testing samples led to selection of a material that fully met all requirements. The C18200 chrome copper forged plates were supplied by the Ampco Metal Division of Ampco-Pittsburgh Corporation

Recovery and reuse of hexavalent chromium from aqueous solutions by a hybrid technique of electrodialysis and ion exchange

Energy Technology Data Exchange (ETDEWEB)

Gayathri, R. [Sengunthar Engineering College, Tiruchengode (India). Dept. of Civil Engineering], e-mail: gay3civil@gmail.com; Senthil Kumar, P. [SSN College of Engineering, Chennai (India). Dept. of Chemical Engineering], E-mail: senthilkumarp@ssn.edu.in

2010-01-15

The chrome plating industry is one of the highly polluting industries whose effluent mainly consists of chromium(VI). This compound is highly toxic to aquatic life and human health. The rinse water constituents reflect the chrome plating bath characteristics; generally dead tank wash water contains about 1% of the plating bath concentration. Other metals and metal compounds usually considered as toxic can be precipitated out by suitably adjusting the pH of the wastewaters. However, Cr(VI) is soluble in almost all pH ranges and therefore an efficient treatment is required for the removal and recovery of chromium, and also for the reuse of wastewaters. The present study aims to recover the chromium by a hybrid technique of electrodialysis and ion exchange for the removal and concentration of chromate ions from the effluent. The different modes of operation like batch recirculation process, batch recirculation process with continuous dipping and continuous process were carried out to remove and recover the chromium from the effluent and the percentage reductions of chromium were found to be 98.69%, 99.18% and 100%, respectively. (author)

Recovery and reuse of hexavalent chromium from aqueous solutions by a hybrid technique of electrodialysis and ion exchange

International Nuclear Information System (INIS)

Gayathri, R.; Senthil Kumar, P.

2010-01-01

The chrome plating industry is one of the highly polluting industries whose effluent mainly consists of chromium(VI). This compound is highly toxic to aquatic life and human health. The rinse water constituents reflect the chrome plating bath characteristics; generally dead tank wash water contains about 1% of the plating bath concentration. Other metals and metal compounds usually considered as toxic can be precipitated out by suitably adjusting the pH of the wastewaters. However, Cr(VI) is soluble in almost all pH ranges and therefore an efficient treatment is required for the removal and recovery of chromium, and also for the reuse of wastewaters. The present study aims to recover the chromium by a hybrid technique of electrodialysis and ion exchange for the removal and concentration of chromate ions from the effluent. The different modes of operation like batch recirculation process, batch recirculation process with continuous dipping and continuous process were carried out to remove and recover the chromium from the effluent and the percentage reductions of chromium were found to be 98.69%, 99.18% and 100%, respectively. (author)

Vi-da: vitiligo diagnostic assistance mobile application

Science.gov (United States)

Nugraha, G. A.; Nurhudatiana, A.; Bahana, R.

2018-03-01

Vitiligo is a skin disorder in which white patches of depigmentation appear on different parts of the body. Usually, patients come to hospitals or clinics to have their vitiligo conditions assessed. This can be very tiring to the patients, as vitiligo treatments usually take a relatively long period of time, which can range from months to years. To address this challenge, we present in this paper a prototype of an Android-based mobile application called Vi-DA, which stands for Vitiligo Diagnostic Assistance. Vi-DA consists of three subsystems, which are user sign-up subsystem, camera and image analysis subsystem, and progress report subsystem. The mobile application was developed in Java programming language and uses MySQL as the database system. Vi-DA adopts a vitiligo segmentation algorithm to segment input image into normal skin area, vitiligo skin area, and non-skin area. Results showed that Vi-DA gave comparable results to the previous system implemented in Matlab. User acceptance testing results also showed that all respondents agreed on the usefulness of the system and agreed to use Vi-DA again in the future. Vi-DA benefits both dermatologists and patients as not only a computer-aided diagnosis (CAD) tool but also as a smart application that can be used for self-assessment at home.

Nucleotide sequence and genetic organization of Hungarian grapevine chrome mosaic nepovirus RNA2.

Science.gov (United States)

Brault, V; Hibrand, L; Candresse, T; Le Gall, O; Dunez, J

1989-10-11

The complete nucleotide sequence of hungarian grapevine chrome mosaic nepovirus (GCMV) RNA2 has been determined. The RNA sequence is 4441 nucleotides in length, excluding the poly(A) tail. A polyprotein of 1324 amino acids with a calculated molecular weight of 146 kDa is encoded in a single long open reading frame extending from nucleotides 218 to 4190. This polyprotein is homologous with the protein encoded by the S strain of tomato black ring virus (TBRV) RNA2, the only other nepovirus sequenced so far. Direct sequencing of the viral coat protein and in vitro translation of transcripts derived from cDNA sequences demonstrate that, as for comoviruses, the coat protein is located at the carboxy terminus of the polyprotein. A model for the expression of GCMV RNA2 is presented.

ViA: a perceptual visualization assistant

Science.gov (United States)

Healey, Chris G.; St. Amant, Robert; Elhaddad, Mahmoud S.

2000-05-01

This paper describes an automated visualized assistant called ViA. ViA is designed to help users construct perceptually optical visualizations to represent, explore, and analyze large, complex, multidimensional datasets. We have approached this problem by studying what is known about the control of human visual attention. By harnessing the low-level human visual system, we can support our dual goals of rapid and accurate visualization. Perceptual guidelines that we have built using psychophysical experiments form the basis for ViA. ViA uses modified mixed-initiative planning algorithms from artificial intelligence to search of perceptually optical data attribute to visual feature mappings. Our perceptual guidelines are integrated into evaluation engines that provide evaluation weights for a given data-feature mapping, and hints on how that mapping might be improved. ViA begins by asking users a set of simple questions about their dataset and the analysis tasks they want to perform. Answers to these questions are used in combination with the evaluation engines to identify and intelligently pursue promising data-feature mappings. The result is an automatically-generated set of mappings that are perceptually salient, but that also respect the context of the dataset and users' preferences about how they want to visualize their data.

Comparison of U(VI) adsorption onto nanoscale zero-valent iron and red soil in the presence of U(VI)–CO{sub 3}/Ca–U(VI)–CO{sub 3} complexes

Energy Technology Data Exchange (ETDEWEB)

Zhang, Zhibin [Key Laboratory of Radioactive Geology and Exploration Technology Fundamental Science for National Defense, East China Institute of Technology, Nanchang 330013 (China); State Key Laboratory Breeding Base of Nuclear Resources and Environment (East China Institute of Technology), Ministry of Education, Nanchang 330013 (China); Chemistry, Biological and Materials Sciences Department, East China Institute of Technology, Nanchang 330013 (China); Liu, Jun [State Key Laboratory Breeding Base of Nuclear Resources and Environment (East China Institute of Technology), Ministry of Education, Nanchang 330013 (China); Cao, Xiaohong, E-mail: xhcao@ecit.cn [Key Laboratory of Radioactive Geology and Exploration Technology Fundamental Science for National Defense, East China Institute of Technology, Nanchang 330013 (China); State Key Laboratory Breeding Base of Nuclear Resources and Environment (East China Institute of Technology), Ministry of Education, Nanchang 330013 (China); Chemistry, Biological and Materials Sciences Department, East China Institute of Technology, Nanchang 330013 (China); Luo, Xuanping [Chemistry, Biological and Materials Sciences Department, East China Institute of Technology, Nanchang 330013 (China); Hua, Rong; Liu, Yan [Key Laboratory of Radioactive Geology and Exploration Technology Fundamental Science for National Defense, East China Institute of Technology, Nanchang 330013 (China); State Key Laboratory Breeding Base of Nuclear Resources and Environment (East China Institute of Technology), Ministry of Education, Nanchang 330013 (China); Chemistry, Biological and Materials Sciences Department, East China Institute of Technology, Nanchang 330013 (China); Yu, Xiaofeng; He, Likai [Chemistry, Biological and Materials Sciences Department, East China Institute of Technology, Nanchang 330013 (China); and others

2015-12-30

Highlights: • NZVI can be used for adsorbing U(VI)–CO{sub 3} complexes. • Use of NZVI is feasible for remediation of uranium-contaminated soils. • The mechanism of U(VI)–CO{sub 3} complexes adsorbing onto NZVI has been explained. - Abstract: The influence of U(VI)–CO{sub 3} and Ca–U(VI)–CO{sub 3} complexes on U(VI) adsorption onto red soil and nanoscale zero-valent iron (NZVI) was investigated using batch adsorption and fixed-bed column experiments to simulate the feasibility of NZVI as the reactive medium in permeable- reactive barriers (PRB) for in situ remediation of uranium-contaminated red soils. The adsorption capacity (q{sub e}) and distribution constant (K{sub d}) of NZVI and red soil decreased with increasing pH, dissolved carbonate and calcium concentrations, but the q{sub e} and K{sub d} values of NZVI were 5–10 times higher than those of red soil. The breakthrough pore volume (PV) values increased with the decrease of pH, dissolved carbonate and calcium concentration; however, the breakthrough PV values of the PRB column filled with 5% NZVI were 2.0–3.5 times higher than the 100% red soil column. The U(VI)–CO{sub 3} complexes adsorbed onto the surface of red soil/NZVI (≡SOH) to form SO–UO{sub 2}CO{sub 3}{sup −} or SO–UO{sub 2} (CO{sub 3}){sub 2}{sup 3−}. XPS and XRD analysis further confirmed the reduction of U(VI) to U(IV) and the formation of FeOOH on NZVI surfaces. The findings of this study are significant to the remediation of uranium-contaminated red soils and the consideration of practical U(VI) species in the natural environment.

Study of new U(VI) and Pu(VI) coprecipitation methods for the preparation of (U,Pu)O2

International Nuclear Information System (INIS)

Sanoit, J. de.

1990-01-01

Two U(VI) and Pu(VI) coprecipitation methods have been studied, for the definition of new processes to prepare (U,Pu)O 2 mixed oxides suitable for making MoX fuels or fast breeder reactor fuels. The first system is based on the coprecipitation of a new U(VI), Pu(VI) compound; ammonium uranoplutonate, where as a second system is related to the precipitation of uranyl plutonyl monocarbonate. Experimental conditions to optimize the precipitation and the filtration steps of these two systems have been determined. After calcination under reducing conditions, the mixed oxides obtained are characterized according to different techniques: granulometry, thermogravimetry, solubility in boiling HNO 3 solutions. The properties of such oxides are excellent. The possible processes for preparing (U, Pu)O 2 using these new routes are compared with those actually exploited [fr

Cr(VI) removal from aqueous solution by dried activated sludge biomass

International Nuclear Information System (INIS)

Wu Jun; Zhang Hua; He Pinjing; Yao Qian; Shao Liming

2010-01-01

Batch experiments were conducted to remove Cr(VI) from aqueous solution using activated sludge biomass. The effects of acid pretreatment of the biomass, initial pH, biomass and Cr(VI) concentrations on Cr(VI) removal efficiency were investigated. Proton consumption during the removal process and the reducing capacity of sludge biomass were studied. The results show that acid pretreatment could significantly improve Cr(VI) removal efficiency and increase Cr(VI) reducing capacity by 20.4%. Cr(VI) removal was remarkably pH-dependent; lower pH (pH = 1, 2) facilitated Cr(VI) reduction while higher pH (pH = 3, 4) favored sorption of the converted Cr(III). Lower Cr(VI) concentration as well as higher biomass concentration could accelerate Cr(VI) removal. Cr(VI) reduction was not the only reason for proton consumption in the removal process. Pseudo-second-order adsorption kinetic model could successfully simulate Cr(VI) removal except under higher pH conditions (pH = 3, 4).

Behaviour of chromium(VI) in stormwater soil infiltration systems

DEFF Research Database (Denmark)

Cederkvist, Karin; Ingvertsen, Simon T.; Jensen, Marina B.

2013-01-01

mm in 2 h) and extreme (100 mm in 3 h) rain events. The objectives were to understand the behaviour of the anionic and toxic Cr(VI) in soil at neutral pH and to asses treatment efficiency towards Cr(VI). During normal rain events Cr(VI) was largely retained (more than 50, even though pH was neutral......The ability of stormwater infiltration systems to retain Cr(VI) was tested by applying a synthetic stormwater runoff solution with a neutral pH and high Cr(VI) concentrations to four intact soil columns excavated from two roadside infiltration swales in Germany. Inlet flow rates mimicked normal (10......, while under extreme rain events approximately 20% of Cr(VI) was retained. In both cases effluent concentrations of Cr(VI) would exceed the threshold value of 3.4 mu g/L if the infiltrated water were introduced to freshwater environments. More knowledge on the composition of the stormwater runoff...

Isolation of a star-shaped uranium(V/VI) cluster from the anaerobic photochemical reduction of uranyl(VI)

Energy Technology Data Exchange (ETDEWEB)

Chatelain, Lucile; White, Sarah; Scopelliti, Rosario; Mazzanti, Marinella [Ecole Polytechnique Federale de Lausanne (EPFL) (Switzerland). Inst. de Sciences et Ingenierie Chimiques

2016-11-07

Actinide oxo clusters are an important class of compounds due to their impact on actinide migration in the environment. The photolytic reduction of uranyl(VI) has potential application in catalysis and spent nuclear fuel reprocessing, but the intermediate species involved in this reduction have not yet been elucidated. Here we show that the photolysis of partially hydrated uranyl(VI) in anaerobic conditions leads to the reduction of uranyl(VI), and to the incorporation of the resulting U{sup V} species into the stable mixed-valent star-shaped U{sup VI}/U{sup V} oxo cluster [U(UO{sub 2}){sub 5}(μ{sub 3}-O){sub 5}(PhCOO){sub 5}(Py){sub 7}]. This cluster is only the second example of a U{sup VI}/U{sup V} cluster and the first one associating uranyl groups to a non-uranyl(V) center. The U{sup V} center in 1 is stable, while the reaction of uranyl(V) iodide with potassium benzoate leads to immediate disproportionation and formation of the U{sub 12}{sup IV}U{sub 4}{sup V}O{sub 24} cluster {[K(Py)_2]_2[K(Py)]_2[U_1_6O_2_4(PhCOO)_2_4(Py)_2]}.

Microbial Precipitation of Cr(III)-Hydroxide and Se(0) Nanoparticles During Anoxic Bioreduction of Cr(VI)- and Se(VI)-Contaminated Water.

Science.gov (United States)

Kim, Yumi; Oh, Jong-Min; Roh, Yul

2017-04-01

This study examined the microbial precipitations of Cr(III)-hydroxide and Se(0) nanoparticles during anoxic bioreductions of Cr(VI) and Se(VI) using metal-reducing bacteria enriched from groundwater. Metal-reducing bacteria enriched from groundwater at the Korea Atomic Energy Research Institute (KAERI) Underground Research Tunnel (KURT), Daejeon, S. Korea were used. Metal reduction and precipitation experiments with the metal-reducing bacteria were conducted using Cr(VI)- and Se(VI)-contaminated water and glucose as a carbon source under an anaerobic environment at room temperature. XRD, SEM-EDX, and TEM-EDX analyses were used to characterize the mineralogy, crystal structure, chemistry, shape, and size distribution of the precipitates. The metal-reducing bacteria reduced Cr(VI) of potassium chromate (K₂CrO₄) to Cr(III) of chromium hydroxide [Cr(OH)3], and Se(VI) of sodium selenate (Na₂SeO₄) to selenium Se(0), with changes of color and turbidity. XRD, SEM-EDX, and TEM-EDX analyses revealed that the chromium hydroxide [Cr(OH)₃] was formed extracellularly with nanoparticles of 20–30 nm in size, and elemental selenium Se(0) nanoparticles had a sphere shape of 50–250 nm in size. These results show that metal-reducing bacteria in groundwater can aid or accelerate precipitation of heavy metals such as Cr(VI) and Se(VI) via bioreduction processes under anoxic environments. These results may also be useful for the recovery of Cr and Se nanoparticles in natural environments.

ViLLaGEs: opto-mechanical design of an on-sky visible-light MEMS-based AO system

Science.gov (United States)

Grigsby, Bryant; Lockwood, Chris; Baumann, Brian; Gavel, Don; Johnson, Jess; Ammons, S. Mark; Dillon, Daren; Morzinski, Katie; Reinig, Marc; Palmer, Dave; Severson, Scott; Gates, Elinor

2008-07-01

Visible Light Laser Guidestar Experiments (ViLLaGEs) is a new Micro-Electro Mechanical Systems (MEMS) based visible-wavelength adaptive optics (AO) testbed on the Nickel 1-meter telescope at Lick Observatory. Closed loop Natural Guide Star (NGS) experiments were successfully carried out during engineering during the fall of 2007. This is a major evolutionary step, signaling the movement of AO technologies into visible light with a MEMS mirror. With on-sky Strehls in I-band of greater than 20% during second light tests, the science possibilities have become evident. Described here is the advanced engineering used in the design and construction of the ViLLaGEs system, comparing it to the LickAO infrared system, and a discussion of Nickel dome infrastructural improvements necessary for this system. A significant portion of the engineering discussion revolves around the sizable effort that went towards eliminating flexure. Then, we detail upgrades to ViLLaGEs to make it a facility class instrument. These upgrades will focus on Nyquist sampling the diffraction limited point spread function during open loop operations, motorization and automation for technician level alignments, adding dithering capabilities and changes for near infrared science.

Nitrate Enhanced Microbial Cr(VI) Reduction-Final Report

Energy Technology Data Exchange (ETDEWEB)

John F. Stolz

2011-06-15

A major challenge for the bioremediation of radionuclides (i.e., uranium, technetium) and metals (i.e., Cr(VI), Hg) is the co-occurrence of nitrate as it can inhibit metal transformation. Denitrification (nitrate reduction to dinitrogen gas) is considered the most important ecological process. For many metal and metalloid reducing bacteria, however, ammonia is the end product through respiratory nitrate reduction (RNRA). The focus of this work was to determine how RNRA impacts Cr(VI) transformation. The goal was to elucidate the specific mechanism(s) that limits Cr(VI) reduction in the presence of nitrate and to use this information to develop strategies that enhance Cr(VI) reduction (and thus detoxification). Our central hypothesis is that nitrate impacts the biotransformation of metals and metalloids in three ways 1) as a competitive alternative electron acceptor (inhibiting transformation), 2) as a co-metabolite (i.e., concomitant reduction, stimulating transformation), and 3) as an inducer of specific proteins and pathways involved in oxidation/reduction reactions (stimulating transformation). We have identified three model organisms, Geobacter metallireducens (mechanism 1), Sulfurospirillum barnesii, (mechasism 2), and Desulfovibrio desulfuricans (mechanisms 3). Our specific aims were to 1) investigate the role of Cr(VI) concentration on the kinetics of both growth and reduction of nitrate, nitrite, and Cr(VI) in these three organisms; 2) develop a profile of bacterial enzymes involved in nitrate transformation (e.g., oxidoreductases) using a proteomic approach; 3) investigate the function of periplasmic nitrite reductase (Nrf) as a chromate reductase; and 4) develop a strategy to maximize microbial chromium reduction in the presence of nitrate. We found that growth on nitrate by G. metallireducens was inhibited by Cr(VI). Over 240 proteins were identified by LC/MS-MS. Redox active proteins, outer membrane heavy metal efflux proteins, and chemotaxis sensory

Learning the vi and Vim Editor

CERN Document Server

Robbins, Arnold; Hannah, Elbert

2008-01-01

There's nothing that hard-core Unix and Linux users are more fanatical about than their text editor. Editors are the subject of adoration and worship, or of scorn and ridicule, depending upon whether the topic of discussion is your editor or someone else's. vi has been the standard editor for close to 30 years. Popular on Unix and Linux, it has a growing following on Windows systems, too. Most experienced system administrators cite vi as their tool of choice. And since 1986, this book has been the guide for vi. However, Unix systems are not what they were 30 years ago, and neither is this

Chromium(VI) bioremediation by probiotics.

Science.gov (United States)

Younan, Soraia; Sakita, Gabriel Z; Albuquerque, Talita R; Keller, Rogéria; Bremer-Neto, Hermann

2016-09-01

Chromium is a common mineral in the earth's crust and can be released into the environment from anthropogenic sources. Intake of hexavalent chromium (Cr(VI)) through drinking water and food causes toxic effects, leading to serious diseases, and is a commonly reported environmental problem. Microorganisms can mitigate or prevent the toxic effects caused by heavy metals in addition to having effective resistance mechanisms to prevent cell damage and bind to these metals, sequestering them from the cell surface and removing them from the body. Species of Lactobacillus, Streptococcus, Bacillus and Bifidobacterium present in the human mouth and gut and in fermented foods have the ability to bind and detoxify some of these substances. This review address the primary topics related to Cr(VI) poisoning in animals and humans and the use of probiotics as a way to mitigate or prevent the toxic effects caused by Cr(VI). Further advances in the genetic knowledge of such microorganisms may lead to discoveries which will clarify the most active microorganisms that act as bioprotectants in bodies exposed to Cr(VI) and are an affordable option for people and animals intoxicated by the oral route. © 2016 Society of Chemical Industry. © 2016 Society of Chemical Industry.

The feasibility of BRT corridor VI shelters in Semarang City

Science.gov (United States)

Purnomo, Andi; Setiawan, Moch Fathoni

2018-03-01

Like other big cities in Indonesia, Semarang City as the capital of Central Java Province also has various city problems, one of them is the transportation problem. Transportation problems arise due to increased mobility of society that is not in balanced with the public transportation facilities and infrastructure availability. In order to create a better transportation system, the local government of Semarang City held Trans Semarang bus rapid transit (BRT) which began operating in 2010. This study aims to analyze the feasibility of BRT Trans Semarang corridor VI shelters. This research uses descriptive critique technique. The results are expected to be considered in determining the right policy in creating a better transportation system. Based on observations made, the majority of BRT Trans Semarang corridor VI uses non-permanent shelters and is less feasible to be a BRT shelter. Thus, the local government is expected to improve the feasibility of BRT Trans Semarang shelter so that the sense of security and comfort can be obtained by users of BRT. In addition, the local government is also expected to maintain the quality of services provided. These services include ticket service, the condition of buses, speed and waiting time, as well as the placement and condition of shelters.

Cr(VI) reduction and immobilization by novel carbonaceous modified magnetic Fe_3O_4/halloysite nanohybrid

International Nuclear Information System (INIS)

Tian, Xike; Wang, Weiwei; Tian, Na; Zhou, Chaoxin; Yang, Chao; Komarneni, Sridhar

2016-01-01

Highlights: • A novel magnetic nonohybrids (Fe_3O_4/HNTs@C) were synthesized for Cr(VI) removal. • Cr(VI) was reduced to Cr(III) by Fe_3O_4 nanoparticles and hydroxyl groups. • Cr ions were attached on Fe_3O_4/HNTs@C by ion exchange and coordination interaction. - Abstract: In this work, a novel “Dumbbell-like” magnetic Fe_3O_4/Halloysite nanohybrid (Fe_3O_4/HNTs@C) with oxygen-containing organic group grafting on the surface of natural halloysite nanotubes (HNTs) and homogeneous Fe_3O_4 nanospheres selectively aggregating at the tips of modified halloysite nanotubes was successfully synthesized. XRD, TEM, IR spectroscopy, XPS and VSM were used to characterize this newly halloysite nanohybrid and its formation mechanism was discussed. Cr(VI) ions adsorption experiments showed that the Fe_3O_4/halloysite nanohybrid exhibited higher adsorption ability with a maximum adsorption capacity of 132 mg/L at 303 K, which is about 100 times higher than that of unmodified halloysite nanotubes. More importantly, with the reduction of Fe_3O_4 and electron–donor effect of oxygen-containing organic groups, Cr(VI) ions were easily reduced into low toxicity Cr(III) and then adsorbed onto the surface of halloysite nanohybrid. In addition, appreciable magnetization was observed due to the aggregation of magnetite nanoparticles, which make adsorbent facility separated from aqueous solutions after Cr pollution adsorption.

A novel RE-chrome-boronizing technology assisted by fast multiple rotation rolling treatment at low temperature

Energy Technology Data Exchange (ETDEWEB)

Yuan, Xing-dong [School of Materials Science and Engineering, Shandong University, Jinan 250061 (China); School of Materials Science and Engineering, Shandong Jianzhu University, Jinan 250101 (China); Xu, Bin, E-mail: xubin@sdjzu.edu.cn [School of Materials Science and Engineering, Shandong Jianzhu University, Jinan 250101 (China); Cai, Yu-cheng [School of Materials Science and Engineering, Shandong Jianzhu University, Jinan 250101 (China)

2015-12-01

Highlights: • A nanostructured layer with grain size of approximately 30 nm was successfully fabricated in the upper-layer of carbon steel. • The penetrating rate was enhanced significantly by the fast multiple rotation rolling (FMRR) treatment at low temperature. • A novel and efficient RE-Chrome-Boronizing technology assisted by fast multiple rotation rolling (FMRR) treatment at low temperature was used to fabricate boride layers on the surface of carbon steel. - Abstract: The boride layer was fabricated on the surface of carbon steel by a novel RE-Chrome-Boronizing technology assisted by fast multiple rotation rolling (FMRR) treatment at low temperature. The microstructure of the boride layer was characterized by using scanning electron microscopy (SEM). The microstructure of the top surface layer of substrate was characterized by transmission electron microscopy (TEM) and high resolution rransmission electron microscopy (HRTEM). Experimental results showed that a nanostructured layer with grain size of approximately 30 nm was obtained; the amorphous phase and high-density dislocations were observed in upper-layer of FMRR samples, which led to the reduction of diffusion activation energy of boron atoms. Boride layers fabricated on the FMRR samples are continuous, dense, uniform, and low in brittleness. The penetrating rate was enhanced significantly when the FMRR samples were Cr-Rare earth-boronized at 650 °C for 6 h. The thickness of the boride layer of FMRR samples on carbon steel was approximately 25 μm when the duration was 60 min, which was approximately 1.5 times higher than the original sample. The boride layer consisted of mainly Fe2B, and adheres well to the metallic substrate.

Timing of Secondary Hydrothermal Alteration of the Luobusa Chromitites Constrained by Ar/Ar Dating of Chrome Chlorites

Directory of Open Access Journals (Sweden)

Wei Guo

2018-05-01

Full Text Available Chrome chlorites are usually found as secondary phases formed by hydrothermal alteration of chromite deposits and associated mafic/ultramafic rocks. Here, we report the 40Ar/39Ar age of chrome chlorites separated from the Luobusa massive chromitites which have undergone secondary alteration by CO2-rich hydrothermal fluids. The dating results reveal that the intermediate heating steps (from 4 to 10 of sample L7 generate an age plateau of 29.88 ± 0.42 Ma (MSWD = 0.12, plateau 39Ar = 74.6%, and the plateau data points define a concordant inverse isochron age of 30.15 ± 1.05 Ma (MSWD = 0.08, initial 40Ar/36Ar = 295.8 ± 9.7. The Ar release pattern shows no evidence of later degassing or inherited radiogenic component indicated by an atmospheric intercept, thus representing the age of the hydrothermal activity. Based on the agreement of this hydrothermal age with the ~30 Ma adakitic plutons exposed in nearby regions (the Zedong area, tens of kilometers west Luobusa and the extensive late Oligocene plutonism distributed along the southeastern Gangdese magmatic belt, it is suggested that the hydrothermal fluids are likely related to the ~30 Ma magmatism. The hydrothermal fluid circulation could be launched either by remote plutons (such as the Sangri granodiorite, the nearest ~30 Ma pluton west Luobusa or by a similar coeval pluton in the local Luobusa area (inferred, not found or reported so far. Our results provide important clues for when the listwanites in Luobusa were formed.

Titanium dioxide-based DGT for measuring dissolved As(V), V(V), Sb(V), Mo(VI) and W(VI) in water

DEFF Research Database (Denmark)

Panther, Jared G.; Stewart, Ryan R.; Teasdale, Peter R.

2013-01-01

A titanium dioxide-based DGT method (Metsorb-DGT) was evaluated for the measurement of As(V), V(V), Sb(V), Mo(VI), W(VI) and dissolved reactive phosphorus (DRP) in synthetic waters. Mass vs. time DGT deployments at pH 6.06 (0.01 mol L-1 NaNO3) demonstrated linear uptake of all analytes (R2...... for deployment times >4 h (CDGT=0.27-0.72). For ferrihydrite-DGT, CDGT/CSol values in the range 0.92-1.16 were obtained for As(V), V(V) and DRP, however, Mo(VI), Sb(V) and W(VI) could not be measured to within 15% of the solution concentration (C DGT/CSol 0.02-0.83)....

Når vi taler om 68

DEFF Research Database (Denmark)

Jensen, Henrik; Metz, Georg

Når vi taler om 68 er en intellektuel samtale mellem to ligeværdige gentlemen og skallesmækkere. En essayistisk dyst om porno, RAF, Pittelkow og livsfilosofi......Når vi taler om 68 er en intellektuel samtale mellem to ligeværdige gentlemen og skallesmækkere. En essayistisk dyst om porno, RAF, Pittelkow og livsfilosofi...

Research progress in the electrochemical synthesis of ferrate(VI)

International Nuclear Information System (INIS)

Macova, Zuzana; Bouzek, Karel; Hives, Jan; Sharma, Virender K.; Terryn, Raymond J.; Baum, J. Clayton

2009-01-01

There is renewed interest in the +6 oxidation state of iron, ferrate (VI) (Fe VI O 4 2- ), because of its potential as a benign oxidant for organic synthesis, as a chemical in developing cleaner ('greener') technology for remediation processes, and as an alternative for environment-friendly battery cathodes. This interest has led many researchers to focus their attention on the synthesis of ferrate(VI). Of the three synthesis methods, electrochemical, wet chemical and thermal, electrochemical synthesis has received the most attention due to its ease and the high purity of the product. Moreover, electrochemical processes use an electron as a so-called clean chemical, thus avoiding the use of any harmful chemicals to oxidize iron to the +6 oxidation state. This paper reviews the development of electrochemical methods to synthesize ferrate(VI). The approaches chosen by different laboratories to overcome some of the difficulties associated with the electrochemical synthesis of ferrate(VI) are summarized. Special attention is paid to parameters such as temperature, anolyte, and anode material composition. Spectroscopic work to understand the mechanism of ferrate(VI) synthesis is included. Recent advances in two new approaches, the use of an inert electrode and molten hydroxide salts, in the synthesis of ferrate(VI) are also reviewed. Progress made in the commercialization of ferrate(VI) continuous production is briefly discussed as well

Synthesis, characterization and oxidative behaviour of dioxoruthenium(VI) complexes

International Nuclear Information System (INIS)

Agarwal, D.D.; Rastogi, Rachana

1995-01-01

Dioxoruthenium(VI) complexes are found to give low yield of epoxide but good yield of cyclohexanone. The complexes are electro active giving metal centered Ru VI /Ru V couple. Cis-stilbene gives trans epoxide and benzaldehyde. Norbornene gives exo epoxy norbornene. The selectivity for allylic oxidation is high. In the present note the synthesis of dioxoruthenium(VI) complexes and their oxidation behaviour is reported. The dioxoruthenium(VI) complexes have been stoichiometrically found to be good oxidants. (author). 21 refs., 1 tab

Inhibition of bacterial U(VI) reduction by calcium

International Nuclear Information System (INIS)

Brooks, Scott C.; Fredrickson, Jim K.; Carroll, S. L.; Kennedy, David W.; Zachara, John M.; Plymale, Andrew E.; Kelly, S. D.; Kemner, K. M.; Fendorf, S.

2003-01-01

The rapid kinetics of bacterial U(VI) reduction and low solubility of uraninite (UO2,cr) make this process an attractive option for removing uranium from groundwater. Nevertheless, conditions that may promote or inhibit U(VI) reduction are not well-defined. Recent descriptions of Ca-UO2-CO3 complexes indicate that these species may dominate the aqueous speciation of U(VI) in many environments. We monitored the bacterial reduction of U(VI) in bicarbonate-buffered solution in the presence and absence of Ca. XAFS measurements confirmed the presence of a Ca-U(VI)-CO3 complex in the initial solutions containing calcium. Calcium, at millimolar concentrations (0.45-5 mM), caused a significant decrease in the rate and extent of bacterial U(VI) reduction. Both facultative (Shewanella putrefaciens strain CN32) and obligate (Desulfovibrio desulfuricans, Geobacter sulfurreducens) anaerobic bacteria were affected by the presence of calcium. Reduction of U(VI) ceased when the calculated system Eh re ached -0.046+/- 0.001 V, based on the Ca2UO2(CO3)(3) -- > UO2,cr couple. The results are consistent with the hypothesis that U is a less energetically favorable electron acceptor when the Ca-UO2-CO3 complexes are present. The results do not support Ca inhibition caused by direct interactions with the cells or with the electron donor as the reduction of fumarate or Tc(VII)O-4(-) under identical conditions was unaffected by the presence of Ca

Role of functional groups on Aspergillus niger biomass in the detoxification of hexavalent chromium.

Science.gov (United States)

Narvekar, Sneha; Vaidya, Varsha K

2009-10-01

Chromium (VI) contamination is not uncommon, especially near industries involved in leather tanning, chrome painting, metal cleaning and processing, wood preservation and alloy preparation. The mutagenic and carcinogenic properties of Chromium (VI) necessitate effective remedial processes. Difficulties associated with chemical and physical techniques to remediate a Chromium (VI) contaminated site to EPA recommended level (50 ppm), in addition to higher costs involved, assert the need for bioremedial measures. Biosorption can be one such solution to clean up heavy metal contamination. The objective of this study was to examine the main aspects of a possible strategy for the removal of Chromium (VI), employing Aspergillus niger biomass. The roles played by amines, carboxylic acids, phosphates, in Chromium (VI) biosorption were studied. Amino and the carboxy groups on the fungal cell wall play an important role in sorption. However, the role of carboxy group was far less than amino group. Surface adsorption of Chromium (VI) was also seen by scanning electron microscopy (SEM) thus indicating involvement of ion-exchange and surface adsorption mechanism in removal of Chromium (VI) ions.

Facile synthesis of AgI/BiOI-Bi{sub 2}O{sub 3} multi-heterojunctions with high visible light activity for Cr(VI) reduction

Energy Technology Data Exchange (ETDEWEB)

Wang, Qi [School of Environmental Science and Engineering, Zhejiang Gongshang University, Hangzhou 310018 (China); The Brook Byer Institute for Sustainable Systems and School of Civil and Environmental Engineering, Georgia Institute of Technology, Atlanta 30332 (United States); Shi, Xiaodong; Liu, Enqin [School of Environmental Science and Engineering, Zhejiang Gongshang University, Hangzhou 310018 (China); Crittenden, John C. [The Brook Byer Institute for Sustainable Systems and School of Civil and Environmental Engineering, Georgia Institute of Technology, Atlanta 30332 (United States); Ma, Xiangjuan; Zhang, Yi [School of Environmental Science and Engineering, Zhejiang Gongshang University, Hangzhou 310018 (China); Cong, Yanqing, E-mail: yqcong@hotmail.com [School of Environmental Science and Engineering, Zhejiang Gongshang University, Hangzhou 310018 (China)

2016-11-05

Graphical abstract: Highly visible-light-active AgI/BiOI-Bi{sub 2}O{sub 3} with multi-heterojunctions was developed. - Highlights: • Visible-light-active AgI/BiOI-Bi{sub 2}O{sub 3} with multi-heterojunctions was prepared. • Highly enhanced photocatalytic reduction of Cr(VI) was observed. • k{sub Cr(VI)} on AgI/BiOI-Bi{sub 2}O{sub 3} increased by ca.16 times relative to Bi{sub 2}O{sub 3}. • Decreased E{sub g}, shifted E{sub fb} and reduced charge transfer resistance were observed. • Simultaneous reduction of Cr(VI) and degradation of organics were achieved. - Abstract: AgI sensitized BiOI-Bi{sub 2}O{sub 3} composite (AgI/BiOI-Bi{sub 2}O{sub 3}) with multi-heterojunctions was prepared using simple etching-deposition process. Different characterization techniques were performed to investigate the structural, optical and electrical properties of the as-prepared photocatalysts. It was found that the ternary AgI/BiOI-Bi{sub 2}O{sub 3} composite exhibited: (1) improved photocurrent response, (2) smaller band gap, (3) greatly reduced charge transfer resistance and (4) negative shift of flat band potential, which finally led to easier generation and more efficient separation of photo-generated electron-hole pairs at the hetero-interfaces. Thus, for the reduction of Cr(VI), AgI/BiOI-Bi{sub 2}O{sub 3} exhibited excellent photocatalytic activity under visible light irradiation at near neutral pH. AgI/BiOI-Bi{sub 2}O{sub 3} was optimized when the initial molar ratio of KI to Bi{sub 2}O{sub 3} and AgNO{sub 3} to Bi{sub 2}O{sub 3} was 1:1 and 10%, respectively. The estimated k{sub Cr(VI)} on optimized AgI/BiOI-Bi{sub 2}O{sub 3} was about 16 times that on pure Bi{sub 2}O{sub 3}. Good stability was also observed in cyclic runs, indicating that the current multi-heterostructured photocatalyst is highly desirable for the remediation of Cr(VI)-containing wastewater.

New generation ion-imprinted nanocarrier for removal of Cr(VI) from wastewater

International Nuclear Information System (INIS)

Uygun, Murat; Feyzioğlu, Esra; Özçalışkan, Emir; Caka, Müşerref; Ergen, Aygen; Akgöl, Sinan; Denizli, Adil

2013-01-01

The purpose of this study was to prepare a novel ion-imprinted nanoparticle to remove Cr(VI) ions from waste water. For this, Cr(VI) ions were complexed with 2-methacryloylamido histidine (MAH) and then Cr(VI)-imprinted poly(HEMAH) nanoparticles were synthesized by surfactant-free emulsion polymerization technique. The templates, Cr(VI) ions, were removed from the nanoparticles using 0.1 M of HNO 3 solution. The specific surface area of the Cr(VI)-imprinted poly(HEMAH) nanoparticles was found to be 1,397.85 m 2 /g, and the particle size was calculated as 155.3 nm. These Cr(VI)-imprinted nanoparticles were used for the adsorption/desorption of Cr(VI) ions from its aqueous solutions. The effects of initial Cr(VI) concentration and medium pH on the Cr(VI) adsorption capacity were also studied. The maximum adsorbed amount of Cr(VI) on the imprinted nanoparticles was found to be 3,830.58 mg/g nanoparticle in pH 4.0. In order to investigate the selectivity of the imprinted nanoparticle, adsorption studies were repeated using Cr(III) ions. The selectivity results demonstrated that Cr(VI)-imprinted poly(HEMAH) nanoparticles showed high affinity for the Cr(VI) ions than Cr(III). The Cr(VI)-imprinted nanoparticles were used several times without decreasing their Cr(VI) adsorption capacities

New generation ion-imprinted nanocarrier for removal of Cr(VI) from wastewater

Science.gov (United States)

Uygun, Murat; Feyzioğlu, Esra; Özçalışkan, Emir; Caka, Müşerref; Ergen, Aygen; Akgöl, Sinan; Denizli, Adil

2013-08-01

The purpose of this study was to prepare a novel ion-imprinted nanoparticle to remove Cr(VI) ions from waste water. For this, Cr(VI) ions were complexed with 2-methacryloylamido histidine (MAH) and then Cr(VI)-imprinted poly(HEMAH) nanoparticles were synthesized by surfactant-free emulsion polymerization technique. The templates, Cr(VI) ions, were removed from the nanoparticles using 0.1 M of HNO3 solution. The specific surface area of the Cr(VI)-imprinted poly(HEMAH) nanoparticles was found to be 1,397.85 m2/g, and the particle size was calculated as 155.3 nm. These Cr(VI)-imprinted nanoparticles were used for the adsorption/desorption of Cr(VI) ions from its aqueous solutions. The effects of initial Cr(VI) concentration and medium pH on the Cr(VI) adsorption capacity were also studied. The maximum adsorbed amount of Cr(VI) on the imprinted nanoparticles was found to be 3,830.58 mg/g nanoparticle in pH 4.0. In order to investigate the selectivity of the imprinted nanoparticle, adsorption studies were repeated using Cr(III) ions. The selectivity results demonstrated that Cr(VI)-imprinted poly(HEMAH) nanoparticles showed high affinity for the Cr(VI) ions than Cr(III). The Cr(VI)-imprinted nanoparticles were used several times without decreasing their Cr(VI) adsorption capacities.

New generation ion-imprinted nanocarrier for removal of Cr(VI) from wastewater

Energy Technology Data Exchange (ETDEWEB)

Uygun, Murat, E-mail: muygun@adu.edu.tr [Adnan Menderes University, Kocarl Latin-Small-Letter-Dotless-I Vocational and Training School (Turkey); Feyzioglu, Esra; Oezcal Latin-Small-Letter-Dotless-I skan, Emir; Caka, Mueserref; Ergen, Aygen; Akgoel, Sinan [Ege University, Department of Biochemistry, Faculty of Science (Turkey); Denizli, Adil [Hacettepe University, Department of Chemistry, Faculty of Science (Turkey)

2013-08-15

The purpose of this study was to prepare a novel ion-imprinted nanoparticle to remove Cr(VI) ions from waste water. For this, Cr(VI) ions were complexed with 2-methacryloylamido histidine (MAH) and then Cr(VI)-imprinted poly(HEMAH) nanoparticles were synthesized by surfactant-free emulsion polymerization technique. The templates, Cr(VI) ions, were removed from the nanoparticles using 0.1 M of HNO{sub 3} solution. The specific surface area of the Cr(VI)-imprinted poly(HEMAH) nanoparticles was found to be 1,397.85 m{sup 2}/g, and the particle size was calculated as 155.3 nm. These Cr(VI)-imprinted nanoparticles were used for the adsorption/desorption of Cr(VI) ions from its aqueous solutions. The effects of initial Cr(VI) concentration and medium pH on the Cr(VI) adsorption capacity were also studied. The maximum adsorbed amount of Cr(VI) on the imprinted nanoparticles was found to be 3,830.58 mg/g nanoparticle in pH 4.0. In order to investigate the selectivity of the imprinted nanoparticle, adsorption studies were repeated using Cr(III) ions. The selectivity results demonstrated that Cr(VI)-imprinted poly(HEMAH) nanoparticles showed high affinity for the Cr(VI) ions than Cr(III). The Cr(VI)-imprinted nanoparticles were used several times without decreasing their Cr(VI) adsorption capacities.

ALTERATION OF U(VI)-PHASES UNDER OXIDIZING CONDITIONS

Energy Technology Data Exchange (ETDEWEB)

A.P. Deditius; S. Utsunomiya; R.C. Ewing

2006-02-21

Uranium-(VI) phases are the primary alteration products of the UO{sub 2} in spent nuclear fuel and the UO{sub 2+x}, in natural uranium deposits. The U(VI)-phases generally form sheet structures of edge-sharing UO{sub 2}{sup 2+} polyhedra. The complexity of these structures offers numerous possibilities for coupled-substitutions of trace metals and radionuclides. The incorporation of radionuclides into U(VI)-structures provides a potential barrier to their release and transport in a geologic repository that experiences oxidizing conditions. In this study, we have used natural samples of UO{sub 2+x}, to study the U(VI)-phases that form during alteration and to determine the fate of the associated trace elements.

ALTERATION OF U(VI)-PHASES UNDER OXIDIZING CONDITIONS

International Nuclear Information System (INIS)

A.P. Deditius; S. Utsunomiya; R.C. Ewing

2006-01-01

Uranium-(VI) phases are the primary alteration products of the UO 2 in spent nuclear fuel and the UO 2+x , in natural uranium deposits. The U(VI)-phases generally form sheet structures of edge-sharing UO 2 2+ polyhedra. The complexity of these structures offers numerous possibilities for coupled-substitutions of trace metals and radionuclides. The incorporation of radionuclides into U(VI)-structures provides a potential barrier to their release and transport in a geologic repository that experiences oxidizing conditions. In this study, we have used natural samples of UO 2+x , to study the U(VI)-phases that form during alteration and to determine the fate of the associated trace elements

Studies on tempering at different temperatures of the beta phase retained by water quenching in uranium-chromium alloys containing from 0,37 to 4 atoms of chromium percent (1963); Etude du revenu a differentes temperatures de la phase beta retenue par trempe a l'eau dans les alliages uranium-chrome contenant de 0,37 a 4 atomes pour cent de chrome (1963)

Energy Technology Data Exchange (ETDEWEB)

Degois, M [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1962-07-15

The author made a systematic study of the annealing of the beta phase retained by water-quenching in uranium-chromium alloys of concentrations between 0.37 and 4 of chromium percent. It is shown that alloys containing less than 1 atom per cent are transformed at temperatures between room temperature and 250 deg. C according to a bainitic process involving activation energies of the order of 14,500 cal/mole. Alloys containing more than 1 at. per cent are transformed at temperature between 400 and 650 deg. C by way of a germination and growth process involving an activation energy of the order of 33,000 cal/mole. The limit of solubility of chromium in beta uranium plays a fundamental part in the transformations of the alloys. The TTT curves of beta {yields} alpha transformation were drawn by the use of a thermo-dilatometer of very low inertia. The transformation law may be expressed 1 x = exp. (kt){sup n}; x represents the degree of progression of the transformation, k a coefficient dependent on the temperature, and n an exponent depending only on the composition of the alloy. A micrographic and crystallographic study confirmed the results found by dilatometry; in particular it was possible to measure the progression rates of the transformation. (author) [French] L'auteur a fait une etude systematique du revenu de la phase beta retenue par trempe a l'eau dans les alliages uranium-chrome de teneurs comprises entre 0,37 et 4 atomes pour cent de chrome. Il a montre que les alliages qui contiennent moins de 1 atome pour cent de chrome se transforment aux temperatures comprises entre la temperature ordinaire et 250 deg. C selon un processus bainitique mettant en jeu des energies d'activatlon de l'ordre de 14500 cal/mole. Les alliages qui renferment plus de 1 atome pour cent de chrome se transforment aux temperatures comprises entre 400 et 650 deg. C suivant un processus de germination et croissance mettant en jeu une energie d'activation de l'ordre de -33000 cal/mole. La

Oxidation of trimethoprim by ferrate(VI): kinetics, products, and antibacterial activity.

Science.gov (United States)

Anquandah, George A K; Sharma, Virender K; Knight, D Andrew; Batchu, Sudha Rani; Gardinali, Piero R

2011-12-15

Kinetics, stoichiometry, and products of the oxidation of trimethoprim (TMP), one of the most commonly detected antibacterial agents in surface waters and municipal wastewaters, by ferrate(VI) (Fe(VI)) were determined. The pH dependent second-order rate constants of the reactions of Fe(VI) with TMP were examined using acid-base properties of Fe(VI) and TMP. The kinetics of reactions of diaminopyrimidine (DAP) and trimethoxytoluene (TMT) with Fe(VI) were also determined to understand the reactivity of Fe(VI) with TMP. Oxidation products of the reactions of Fe(VI) with TMP and DAP were identified by liquid chromatography-tandem mass spectrometry (LC-MS/MS). Reaction pathways of oxidation of TMP by Fe(VI) are proposed to demonstrate the cleavage of the TMP molecule to ultimately result in 3,4,5,-trimethoxybenzaldehyde and 2,4-dinitropyrimidine as among the final identified products. The oxidized products mixture exhibited no antibacterial activity against E. coli after complete consumption of TMP. Removal of TMP in the secondary effluent by Fe(VI) was achieved.

Social Set Visualizer (SoSeVi) II

DEFF Research Database (Denmark)

Flesch, Benjamin; Vatrapu, Ravi

2016-01-01

This paper reports the second iteration of the Social Set Visualizer (SoSeVi), a set theoretical visual analytics dashboard of big social data. In order to further demonstrate its usefulness in large-scale visual analytics tasks of individual and collective behavior of actors in social networks......, the current iteration of the Social Set Visualizer (SoSeVi) in version II builds on recent advancements in visualizing set intersections. The development of the SoSeVi dashboard involved cutting-edge open source visual analytics libraries (D3.js) and creation of new visualizations such as of actor mobility...

Fremtidens lavenergibyggeri - kan vi gøre som vi plejer?

DEFF Research Database (Denmark)

Larsen, Tine Steen

2011-01-01

Stramninger af kravene til energiforbruget i vores boliger medfører stor fokus på energiberegningen, men erfaringer fra lavenergiboliger opført i dag viser, at vi, for at sikre succes for fremtidens boliger, også skal inddrage dokumentation af indeklimaet og forbedre samarbejdet mellem arkitekter...

Chromium(VI) generation in vadose zone soils and alluvial sediments of the southwestern Sacramento Valley, California: A potential source of geogenic Cr(VI) to groundwater

International Nuclear Information System (INIS)

Mills, Christopher T.; Morrison, Jean M.; Goldhaber, Martin B.; Ellefsen, Karl J.

2011-01-01

Highlights: → Southern Sacramento Valley soil and sediment has abundant naturally-occurring Cr(III). → Cr(III) resides mainly in chromite but some is associated with clays and Fe oxides. → Cr(VI) is mostly absent in surface soil but ubiquitous in deeper soil and sediment. → Cr(VI) increased linearly with time during lab soil incubations with no additions. → Cation exchange processes resulted in greater Cr(VI) generation rates. - Abstract: Concentrations of geogenic Cr(VI) in groundwater that exceed the World Health Organization's maximum contaminant level for drinking water (50 μg L -1 ) occur in several locations globally. The major mechanism for mobilization of this Cr(VI) at these sites is the weathering of Cr(III) from ultramafic rocks and its subsequent oxidation on Mn oxides. This process may be occurring in the southern Sacramento Valley of California where Cr(VI) concentrations in groundwater can approach or exceed 50 μg L -1 . To characterize Cr geochemistry in the area, samples from several soil auger cores (approximately 4 m deep) and drill cores (approximately 25 m deep) were analyzed for total concentrations of 44 major, minor and trace elements, Cr associated with labile Mn and Fe oxides, and Cr(VI). Total concentrations of Cr in these samples ranged from 140 to 2220 mg per kg soil. Between 9 and 70 mg per kg soil was released by selective extractions that target Fe oxides, but essentially no Cr was associated with the abundant reactive Mn oxides (up to ∼1000 mg hydroxylamine-reducible Mn per kg soil was present). Both borehole magnetic susceptibility surveys performed at some of the drill core sites and relative differences between Cr released in a 4-acid digestion versus total Cr (lithium metaborate fusion digestion) suggest that the majority of total Cr in the samples is present in refractory chromite minerals transported from ultramafic exposures in the Coast Range Mountains. Chromium(VI) in the samples studied ranged from 0 to 42 �

Chromium(VI) generation in vadose zone soils and alluvial sediments of the southwestern Sacramento Valley, California: A potential source of geogenic Cr(VI) to groundwater

Energy Technology Data Exchange (ETDEWEB)

Mills, Christopher T., E-mail: cmills@usgs.gov [United States Geological Survey, Crustal Geophysics and Geochemistry Science Center, Denver Federal Center, MS 964D, Denver, CO 80225 (United States); Morrison, Jean M.; Goldhaber, Martin B.; Ellefsen, Karl J. [United States Geological Survey, Crustal Geophysics and Geochemistry Science Center, Denver Federal Center, MS 964D, Denver, CO 80225 (United States)

2011-08-15

Highlights: > Southern Sacramento Valley soil and sediment has abundant naturally-occurring Cr(III). > Cr(III) resides mainly in chromite but some is associated with clays and Fe oxides. > Cr(VI) is mostly absent in surface soil but ubiquitous in deeper soil and sediment. > Cr(VI) increased linearly with time during lab soil incubations with no additions. > Cation exchange processes resulted in greater Cr(VI) generation rates. - Abstract: Concentrations of geogenic Cr(VI) in groundwater that exceed the World Health Organization's maximum contaminant level for drinking water (50 {mu}g L{sup -1}) occur in several locations globally. The major mechanism for mobilization of this Cr(VI) at these sites is the weathering of Cr(III) from ultramafic rocks and its subsequent oxidation on Mn oxides. This process may be occurring in the southern Sacramento Valley of California where Cr(VI) concentrations in groundwater can approach or exceed 50 {mu}g L{sup -1}. To characterize Cr geochemistry in the area, samples from several soil auger cores (approximately 4 m deep) and drill cores (approximately 25 m deep) were analyzed for total concentrations of 44 major, minor and trace elements, Cr associated with labile Mn and Fe oxides, and Cr(VI). Total concentrations of Cr in these samples ranged from 140 to 2220 mg per kg soil. Between 9 and 70 mg per kg soil was released by selective extractions that target Fe oxides, but essentially no Cr was associated with the abundant reactive Mn oxides (up to {approx}1000 mg hydroxylamine-reducible Mn per kg soil was present). Both borehole magnetic susceptibility surveys performed at some of the drill core sites and relative differences between Cr released in a 4-acid digestion versus total Cr (lithium metaborate fusion digestion) suggest that the majority of total Cr in the samples is present in refractory chromite minerals transported from ultramafic exposures in the Coast Range Mountains. Chromium(VI) in the samples studied ranged

Diverse functions of myosin VI elucidated by an isoform-specific α-helix domain.

Science.gov (United States)

Wollscheid, Hans-Peter; Biancospino, Matteo; He, Fahu; Magistrati, Elisa; Molteni, Erika; Lupia, Michela; Soffientini, Paolo; Rottner, Klemens; Cavallaro, Ugo; Pozzoli, Uberto; Mapelli, Marina; Walters, Kylie J; Polo, Simona

2016-04-01

Myosin VI functions in endocytosis and cell motility. Alternative splicing of myosin VI mRNA generates two distinct isoform types, myosin VI(short) and myosin VI(long), which differ in the C-terminal region. Their physiological and pathological roles remain unknown. Here we identified an isoform-specific regulatory helix, named the α2-linker, that defines specific conformations and hence determines the target selectivity of human myosin VI. The presence of the α2-linker structurally defines a new clathrin-binding domain that is unique to myosin VI(long) and masks the known RRL interaction motif. This finding is relevant to ovarian cancer, in which alternative myosin VI splicing is aberrantly regulated, and exon skipping dictates cell addiction to myosin VI(short) in tumor-cell migration. The RRL interactor optineurin contributes to this process by selectively binding myosin VI(short). Thus, the α2-linker acts like a molecular switch that assigns myosin VI to distinct endocytic (myosin VI(long)) or migratory (myosin VI(short)) functional roles.

Development of iron-based nanoparticles for Cr(VI removal from drinking water

Directory of Open Access Journals (Sweden)

Vourlias G.

2013-01-01

Full Text Available A great deal of research over recent decades has been motivated by the requirement to lower the concentration of chromium in drinking water. This study has been conducted to determine the feasibility of iron-based nanoparticles for chromium removal from contaminated water. Single Fe, Fe3O4 and binary Fe/Fe3O4 nanoparticles were grown at the 45-80 nm size range using the solar physical vapor deposition technique and tested as potential hexavalent chromium removing agents from aqueous solutions. Due to their higher electron donation ability compared to the Fe3O4 ones, single Fe nanoparticles exhibited the highest Cr(VI removal capacity of more than 3 µg/mg while maintaining a residual concentration 50 µg/L, equal to the regulation limit for drinking water. In combination to their facile and fast magnetic separation, the applicability of the studied particles in water treatment facilities should be considered.

The reduction of Np(VI) and Pu(VI) by organic chelating agents

International Nuclear Information System (INIS)

Reed, D.T.; Aase, S.B.; Banaszak, J.E.

1998-01-01

The reduction of NpO 2+ and PuO 2 2+ by oxalate. citrate, and ethylenediaminetetraacetic acid (EDTA) was investigated in low ionic strength media and brines. This was done to help establish the stability of the An(VI) oxidation state in the presence of organic complexants. The stability of the An(VI) oxidation state depended on the pH and relative strength of the various oxidation state-specific complexes. At low ionic strength and pH 6, NpO 2 O 2+ was rapidly reduced to form NpO 2 + organic complexes. At longer times, Np(IV) organic complexes were observed in the presence of citrate. PuO 2 2+ was predominantly reduced to Pu 4+ , resulting in the formation of organic complexes or polymeric/hydrolytic precipitates. The relative rates of reduction to the An(V) complex were EDTA > citrate > oxalate. Subsequent reduction to An(IV) complexes, however, occurred in the following order: citrate > EDTA > oxalate because of the stability of the An(V)-EDTA complex. The presence of organic complexants led to the rapid reduction of NpO 2 2+ and PuO 2 P 2+ in G-seep brine at pHs 5 and 7. At pHs 8 and 10 in ERDA-6 brine, carbonate and hydrolytic complexes predominated and slowed down or prevented the reduction of An(VI) by the organics present

20 CFR 655.1116 - Element VI-What notification must facilities provide to registered nurses?

Science.gov (United States)

2010-04-01

... provide to registered nurses? 655.1116 Section 655.1116 Employees' Benefits EMPLOYMENT AND TRAINING... Requirements Must a Facility Meet to Employ H-1C Nonimmigrant Workers as Registered Nurses? § 655.1116 Element VI—What notification must facilities provide to registered nurses? (a) The sixth attestation element...

Structural Fluctuations and Thermophysical Properties of Molten II-VI Compounds

Science.gov (United States)

Su, Ching-Hua; Zhu, Shen; Li, Chao; Scripa, R.; Lehoczky, Sandra L.; Kim, Y. W.; Baird, J. K.; Lin, B.; Ban, Heng; Benmore, Chris

2003-01-01

The objectives of the project are to conduct ground-based experimental and theoretical research on the structural fluctuations and thermophysical properties of molten II-VI compounds to enhance the basic understanding of the existing flight experiments in microgravity materials science programs as well as to study the fundamental heterophase fluctuation phenomena in these melts by: 1) conducting neutron scattering analysis and measuring quantitatively the relevant thermophysical properties of the II-VI melts (such as viscosity, electrical conductivity, thermal diffusivity and density) as well as the relaxation characteristics of these properties to advance the understanding of the structural properties and the relaxation phenomena in these melts and 2) performing theoretical analyses on the melt systems to interpret the experimental results. All the facilities required for the experimental measurements have been procured, installed and tested. It has long been recognized that liquid Te presents a unique case having properties between those of metals and semiconductors. The electrical conductivity for Te melt increases rapidly at melting point, indicating a semiconductor-metal transition. Te melts comprise two features, which are usually considered to be incompatible with each other: covalently bound atoms and metallic-like behavior. Why do Te liquids show metallic behavior? is one of the long-standing issues in liquid metal physics. Since thermophysical properties are very sensitive to the structural variations of a melt, we have conducted extensive thermophysical measurements on Te melt.

Structural Fluctuation and Thermophysical Properties of Molten II-VI Compounds

Science.gov (United States)

2003-01-01

The objectives of the project is to conduct ground-based experimental and theoretical research on the structural fluctuations and thermophysical properties of molten II-VI compounds to enhance the basic understanding of the existing flight experiments in microgravity materials science programs and to study the fundamental heterophase fluctuations phenomena in these melts by: 1) Conducting neutron scattering analysis and measuring quantitatively the relevant thermophysical properties of the II-VI melts such as viscosity, electrical conductivity, thermal diffusivity and density as well as the relaxation characteristics of these properties to advance the understanding of the structural properties and the relaxation phenomena in these melts and 2) Performing theoretical analyses on the melt systems to interpret the experimental results. All the facilities required for the experimental measurements have been procured, installed and tested. A relaxation phenomenon, which shows a slow drift of the measured thermal conductivity toward the equilibrium value after cooling of the sample, was observed for the first time. An apparatus based on the transient torque induced by a rotating magnetic field has been developed to determine the viscosity and electrical conductivity of semiconducting liquids. Viscosity measurements on molten tellurium showed similar relaxation behavior as the measured diffusivity. Neutron scattering experiments were performed on the HgTe and HgZnTe melts and the results on pair distribution showed better resolution than previous reported.

Parallel between steels alloyed with chrome-nickel and Fe-Mn-Al-C steels, in their response to fracture and wear (Review)

International Nuclear Information System (INIS)

Ramos, J; Perez, G.A

2008-01-01

The big worldwide demand for chrome-nickel alloy steels ('conventional steel') leads to the need for advanced materials for applications in different engineering systems that operate at high temperatures and in aggressive environmental conditions, favoring research and development in alternate alloys. In this technological race in search of these new materials, the FeMnAlC alloys ('new steels') have attracted attention for their excellent mechanical and tribological properties as well as for their good performance in corrosive-oxide environments, which make them similar to conventional steel. There are two important similarities between these two steels. First, an agent that causes the passive film to become stainless appears in both steels: chrome in the conventional steel, and aluminum in the FeMnAl alloy. The second similarity is that a stabilizing agent of the austenitic phase (FCC) appears in both, so that excellent mechanical properties can be obtained: nickel in the conventional steel, and manganese in the FeMnAl alloy. In certain sectors, such as aeronautics, conventional steel is rarely used because it is a very heavy material. This conventional steel is almost three times heavier that aluminum (7.85/2.7). Two advantages that the new FeMnAIC steels have compared to the conventional steels are that they are about 13% lighter in weight and they are less expensive. The FeMnAl also have excellent mechanical properties and good corrosion-oxidation resistance, which generates big expectations for their application in a broad scientific spectrum. This work reports the state of the information currently available about FeMnAlC alloys, comparing the mechanical and tribological behaviors of conventional alloy steels with chrome and nickel alloys, specifying the scopes of their application. A condition that favors the steels' fragility is the high speed of deformation and impact, where the FCC crystalline structure materials do not have a fragile ductile transition

Recovery and reuse of hexavalent chromium from aqueous solutions by a hybrid technique of electrodialysis and ion exchange

Directory of Open Access Journals (Sweden)

R. Gayathri

2010-03-01

Full Text Available The chrome plating industry is one of the highly polluting industries whose effluent mainly consists of chromium(VI. This compound is highly toxic to aquatic life and human health. The rinse water constituents reflect the chrome plating bath characteristics; generally dead tank wash water contains about 1% of the plating bath concentration. Other metals and metal compounds usually considered as toxic can be precipitated out by suitably adjusting the pH of the wastewaters. However, Cr(VI is soluble in almost all pH ranges and therefore an efficient treatment is required for the removal and recovery of chromium, and also for the reuse of wastewaters. The present study aims to recover the chromium by a hybrid technique of electrodialysis and ion exchange for the removal and concentration of chromate ions from the effluent. The different modes of operation like batch recirculation process, batch recirculation process with continuous dipping and continuous process were carried out to remove and recover the chromium from the effluent and the percentage reductions of chromium were found to be 98.69%, 99.18% and 100%, respectively.

Contribution to the study of the redox couple Np(VI)/Np(V) in the presence of uranium(VI) in solutions of nitric acid and nitrous acid; Contribution a l'etude du comportement redox du couple Np(VI)/Np(V) en presence d'uranium VI dans les solutions constituees d'acide nitrique et d'acide nitreux

Energy Technology Data Exchange (ETDEWEB)

Arpigny, S. [CEA Marcoule, Dept. de Radiochimie et Procedes, DRP, 30 (France)

2001-07-01

The redox behavior of the Np(VI)/Np(V) couple was the subject of a spectrometric study of the Np(VI) reduction reaction in nitric acid solutions (4 to 5 M) containing variable concentrations (1.5 to 3.5 x 10{sup -3} M) of nitrous acid. A low nitrous acid concentration and a high nitric acid concentration were found to favor the stabilization of Np(VI). The stoichiometric coefficients of nitrous acid and nitric acid in the Np(VI) reduction reaction were determined thermodynamically, although only the reaction order with respect to HNO{sub 2} could be calculated from a kinetic analysis. Adding nitrate ions to a HNO{sub 3}/HNO{sub 2} solution enhanced the stability of neptunium at oxidation state +VI, but also increased the reduction rate. When uranium(VI) was added to the HNO{sub 3}/HNO{sub 2} solutions, the total quantity of neptunium at oxidation state +V (either free or as a Np(V)-U(VI) complex) remained practically unchanged, as did the Np(VI) reduction rate. The electrochemical behavior of the Np(VI)/Np(V) couple was investigated in a weak acidic medium by voltammetry with an ultra-micro-electrode (UME). The oxidation wave limiting current variation was a linear function of the Np(V) concentration when a gold UME was used, but not with a platinum UME; the reduction wave limiting current variation versus the Np(V) concentration was linear with either gold or platinum UMEs. The presence of the Np(V)-U(VI) complex in the neptunium solutions was characterized by a shift in the normal apparent potential of the Np(VI)/Np(V) couple toward anodic potentials consistent with the previously determined values of the complexation constants. (author)

Chromium(VI) generation in vadose zone soils and alluvial sediments of the southwestern Sacramento Valley, California: a potential source of geogenic Cr(VI) to groundwater

Science.gov (United States)

Mills, Christopher T.; Morrison, Jean M.; Goldhaber, Martin B.; Ellefsen, Karl J.

2011-01-01

Concentrations of geogenic Cr(VI) in groundwater that exceed the World Health Organization’s maximum contaminant level for drinking water (50 μg L−1) occur in several locations globally. The major mechanism for mobilization of this Cr(VI) at these sites is the weathering of Cr(III) from ultramafic rocks and its subsequent oxidation on Mn oxides. This process may be occurring in the southern Sacramento Valley of California where Cr(VI) concentrations in groundwater can approach or exceed 50 μg L−1. To characterize Cr geochemistry in the area, samples from several soil auger cores (approximately 4 m deep) and drill cores (approximately 25 m deep) were analyzed for total concentrations of 44 major, minor and trace elements, Cr associated with labile Mn and Fe oxides, and Cr(VI). Total concentrations of Cr in these samples ranged from 140 to 2220 mg per kg soil. Between 9 and 70 mg per kg soil was released by selective extractions that target Fe oxides, but essentially no Cr was associated with the abundant reactive Mn oxides (up to ~1000 mg hydroxylamine-reducible Mn per kg soil was present). Both borehole magnetic susceptibility surveys performed at some of the drill core sites and relative differences between Cr released in a 4-acid digestion versus total Cr (lithium metaborate fusion digestion) suggest that the majority of total Cr in the samples is present in refractory chromite minerals transported from ultramafic exposures in the Coast Range Mountains. Chromium(VI) in the samples studied ranged from 0 to 42 μg kg−1, representing a minute fraction of total Cr. Chromium(VI) content was typically below detection in surface soils (top 10 cm) where soil organic matter was high, and increased with increasing depth in the soil auger cores as organic matter decreased. Maximum concentrations of Cr(VI) were up to 3 times greater in the deeper drill core samples than the shallow auger cores. Although Cr(VI) in these vadose zone soils and sediments was only a

Establishment of Wear Resistant HVOF Coatings for 50CrMo4 Chromium Molybdenum Alloy Steel as an Alternative for Hard Chrome Plating

Science.gov (United States)

Karuppasamy, S.; Sivan, V.; Natarajan, S.; Kumaresh Babu, S. P.; Duraiselvam, M.; Dhanuskodi, R.

2018-05-01

High cost imported components of seamless steel tube manufacturing plants wear frequently and need replacement to ensure the quality of the product. Hard chrome plating, which is time consuming and hazardous, is conventionally used to restore the original dimension of the worn-out surface of the machine components. High Velocity Oxy-Fuel (HVOF) thermal spray coatings with NiCrBSi super alloy powder and Cr3C2 NiCr75/25 alloy powder applied on a 50CrMo4 (DIN-1.7228) chromium molybdenum alloy steel, the material of the wear prone machine component, were evaluated for use as an alternative for hard chrome plating in this present work. The coating characteristics are evaluated using abrasive wear test, sliding wear test and microscopic analysis, hardness test, etc. The study results revealed that the HVOF based NiCrBSi and Cr3C2NiCr75/25 coatings have hardness in the range of 800-900 HV0.3, sliding wear rate in the range of 50-60 µm and surface finish around 5 microns. Cr3C2 NiCr75/25 coating is observed to be a better option out of the two coatings evaluated for the selected application.

Vi behøver innovation

DEFF Research Database (Denmark)

McAloone, Tim C.

2007-01-01

-Produktion og Maskiner. Innovation og bæredygtighed er to områder som vi i Skandinavien giver meget stor opmærksomhed for at kunne vedligeholde vores globale konkurrencekraft og stærke velfærdssamfund. Gennem årene har mange brancher bidraget til skabelsen af vidensbaserede innovationer, og det faktum, at de......Analyse: Vi behøver innovation En ny miljøbølge ruller, og danske virksomheder bør ride med Af Tim McAloone, fredag 02. feb 2007 kl. 04:50 Tim McAloone Lektor og ph.d. ved Institut for mekanik, energi og konstruktion ved DTU. Tim McAloone skriver fremover jævnligt kommentarer i Ingeniøren...... skandinaviske lande er relativt små, har ledt til en interessant evne til at etablere og derefter samarbejde inden for tætte netværk, som strækker sig over både faglige og geografiske grænser. Samtidig har vi set miljøhensyn vinde og tabe samfundsmæssig og industriel opmærksomhed på en nærmest periodisk basis...

Thermodynamic analysis of Cr(VI) extraction using TOPO impregnated membranes

Energy Technology Data Exchange (ETDEWEB)

Praveen, Prashant; Loh, Kai-Chee, E-mail: chelohkc@nus.edu.sg

2016-08-15

Highlights: • Cr(VI) extraction by extractant impregnated membranes (EIM) was investigated. • EIM exhibited high extraction efficiency, mass transfer rate and stability. • Mass transfer mechanism was proposed based on kinetics and equilibrium data. • Uptake of Cr(VI) by EIMs was endothermic and spontaneous. • Cr(VI) extraction by EIMs was dominated by physical interactions. - Abstract: Solid/liquid extraction of Cr(VI) was accomplished using trioctylphosphine oxide impregnated polypropylene hollow fiber membranes. Extraction of 100–500 mg/L Cr(VI) by the extractant impregnated membranes (EIM) was characterized by high uptake rate and capacity, and equilibrium was attained within 45 min of contact. Extraction equilibrium was pH-dependent (at an optimal pH 2), whereas stripping using 0.2 M sodium hydroxide yielded the highest recovery of 98% within 60 min. The distribution coefficient was independent of initial Cr(VI) concentration, and the linear distribution equilibrium isotherm could be modeled using Freundlich isotherm. The mass transfer kinetics of Cr(VI) was examined using pseudo-second-order and intraparticle diffusion models and a mass transfer mechanism was deduced. The distribution coefficient increased with temperature, which indicated endothermic nature of the reaction. Enthalpy and entropy change during Cr(VI) extraction were positive and varied in the range of 37–49 kJ/mol and 114–155 J/mol, respectively. The free energy change was negative, confirming the feasibility and spontaneity of the mass transfer process. Results obtained suggest that EIMs are efficient and sustainable for extraction of Cr(VI) from wastewater.

Influence of Calcium on Microbial Reduction of Solid Phase Uranium (VI)

International Nuclear Information System (INIS)

Liu, Chongxuan; Jeon, Byong-Hun; Zachara, John M.; Wang, Zheming

2007-01-01

The effect of calcium on microbial reduction of a solid phase U(VI), sodium boltwoodite (NaUO2SiO3OH · 1.5H2O), was evaluated in a culture of a dissimilatory metal-reducing bacterium (DMRB), Shewanella oneidensis strain MR-1. Batch experiments were performed in a non-growth bicarbonate medium with lactate as electron donor at pH 7 buffered with PIPES. Calcium increased both the rate and extent of Na-boltwoodite dissolution by increasing its solubility through the formation of a ternary aqueous calcium-uranyl-carbonate species. The ternary species, however, decreased the rates of microbial reduction of aqueous U(VI). Laser-induced fluorescence spectroscopy (LIFS) and transmission electron microscopy (TEM) revealed that microbial reduction of solid phase U(VI) is a sequentially coupled process of Na-boltwoodite dissolution, U(VI) aqueous speciation, and microbial reduction of dissolved U(VI) to U(IV) that accumulated on bacterial surfaces/periplasm. The overall rates of microbial reduction of solid phase U(VI) can be described by the coupled rates of dissolution and microbial reduction that were both influenced by calcium. The results demonstrated that dissolved U(VI) concentration during microbial reduction was a complex function of solid phase U(VI) dissolution kinetics, aqueous U(VI) speciation, and microbial activity

A simple Cr(VI)–S(IV)–O{sub 2} system for rapid and simultaneous reduction of Cr(VI) and oxidative degradation of organic pollutants

Energy Technology Data Exchange (ETDEWEB)

Yuan, Yanan; Yang, Shaojie [Department of Environmental Science, Hubei Key Lab of Biomass Resource Chemistry and Environmental Biotechnology, School of Resources and Environmental Science, Wuhan University, 430079 (China); Zhou, Danna, E-mail: zdncug@163.com [Faculty of Material Science and Chemistry, China University of Geosciences, Wuhan 430074 (China); Wu, Feng [Department of Environmental Science, Hubei Key Lab of Biomass Resource Chemistry and Environmental Biotechnology, School of Resources and Environmental Science, Wuhan University, 430079 (China)

2016-04-15

Highlights: • Rapid and simultaneous reduction of Cr(VI) and degradation of organic pollutants occur. • Oxysulfur radicals generated in Cr(VI)–S(IV)–O{sub 2} system oxidize the organic pollutants. • Acidic pH facilitates the reactions from both directions of reduction and oxidation. • Degradation potential of aromatic amines depends on the substituted groups. • Cr(VI)–S(IV)–O{sub 2} system is promising for “waste control by waste”. - Abstract: Hexavalent chromium (Cr(VI)), a heavy-metal contaminant, can be easily reduced to less toxic trivalent chromium (Cr(III)) by sulfite ions (S(IV)). However, S(IV) has not drawn as much attention as the ferrous ion has. We report herein a novel Cr(VI)–S(IV)–O{sub 2} system containing sulfite ions that rapidly and simultaneously reduces Cr(VI) and oxidize organic pollutants in the presence of oxygen in aqueous solutions. This Cr(VI)–S(IV)-O{sub 2} system contains the initiator Cr(VI), the reductant S(IV), and the oxidant O{sub 2}, which produce oxysulfur radicals (mainly SO{sub 4}·{sup −} and SO{sub 5}·{sup −}) and hydroxyl radicals (OH·). The Cr(VI)/S(IV) molar ratio, pH, and oxygen content play important roles in the entire reaction system. Acidic conditions (pH 3.0) facilitated degradation of organic compounds and reduction of Cr(VI) as well. In addition, experiments of rapid degradation of several kinds of organic pollutants such as azo dye (acid orange 7, AO7), aniline, phenol, bisphenol A etc were also conducted. Preliminary results show that the removal rates of the analogs of phenols or aromatic amines in this Cr(VI)–S(IV)–O{sub 2} system have a relationship with the electronic parameters (Hammett constant, σ) of the substituted groups. Thus, the Cr(VI)–S(IV)–O{sub 2} system, provides an excellent strategy of “waste control by waste” for removing multiple industrial contaminants.

77 FR 64399 - Order of Succession for HUD Region VI

Science.gov (United States)

2012-10-19

... Region VI AGENCY: Office of Field Policy and Management, HUD. ACTION: Notice of Order of Succession... its Field Offices (Region VI). This Order of Succession supersedes all previous Orders of Succession for HUD Region VI. DATES: Effective Date: October 9, 2012. FOR FURTHER INFORMATION CONTACT: Lawrence D...

Nanoscale investigation of the degradation mechanism of a historical chrome yellow paint by quantitative electron energy loss spectroscopy mapping of chromium species.

Science.gov (United States)

Tan, Haiyan; Tian, He; Verbeeck, Jo; Monico, Letizia; Janssens, Koen; Van Tendeloo, Gustaaf

2013-10-18

Getting the picture: The investigation of 100 year old chrome yellow paint by transmission electron microscopy and spectroscopy has led to the identification of four types of core-shell particles. This nanoscale investigation has allowed a mechanism to be proposed for the darkening of some bright yellow colors in Van Gogh's paintings (e.g. in Falling leaves (Les Alyscamps), 1888). Copyright © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Extraction behavior of uranium(VI) with polyurethane foam

International Nuclear Information System (INIS)

Tingchia Huang; Donghwang Chen; Muchang Shieh; Chingtsven Huang

1992-01-01

The extraction of uranium(VI) from aqueous solution with polyether-based polyurethane (PU) foam was studied. The effects of the kinds and concentrations of nitrate salts, uranium(VI) concentration, temperature, nitric acid concentration, pH, the content of poly(ethylene oxide) in the polyurethane foam, and the ratio of PU foam weight and solution volume on the extraction of uranium(VI) were investigated. The interferences of fluoride and carbonate ions on the extraction of uranium(VI) were also examined, and methods to overcome both interferences were suggested. It was found that no uranium was extracted in the absence of a nitrate salting-out agent, and the extraction behaviors of uranium(IV) with polyurethane foam could be explained in terms of an etherlike solvent extraction mechanism. In addition, the percentage extraction of a multiple stage was also estimated theoretically

Ecologically sustainable coating technology. BehrOxal process; Oekologisch nachhaltige Beschichtungstechnologie. BehrOxal-Verfahren

Energy Technology Data Exchange (ETDEWEB)

Anon.

2007-10-15

Since 1st July, 2007, any more hexavalent chromium (chromium(VI)) has to be used in vehicles. Two years ago, Behr GmbH and Co. KG (Stuttgart, Federal Republic of Germany) developed a new procedure in order to coat evaporators in air conditioners perfectly chrome-free. Since one year, the coating process is used serially. The resonance of the customers is positively throughout - so the manufacturer.

Paul Scherrer Institute Scientific Report 1998. Volume VI: Large Research Facilities

International Nuclear Information System (INIS)

Bauer, Guenter; Bercher, Renate; Buechli, Carmen; Foroughi, Fereydoun; Meyer, Rosa

1999-01-01

The department GFA (Grossforschungsanlagen, Large Research Facilities) has been established in October 1998 and its main duty is operation, maintenance and development of the PSI accelerators, the spallation neutron source and the beam transport systems for pions and muons. A large effort of this group concerns the planning and co-ordination of the assembly of the Swiss Light Source (SLS). (author)

Vi-CRM 197 as a new conjugate vaccine against Salmonella Typhi.

Science.gov (United States)

Micoli, F; Rondini, S; Pisoni, I; Proietti, D; Berti, F; Costantino, P; Rappuoli, R; Szu, S; Saul, A; Martin, L B

2011-01-17

An efficacious, low cost vaccine against typhoid fever, especially for young children, would make a major impact on disease burden in developing countries. The virulence capsular polysaccharide of Salmonella Typhi (Vi) coupled to recombinant mutant Pseudomonas aeruginosa exoprotein A (Vi-rEPA) has been shown to be highly efficacious. We investigated the use of carrier proteins included in infant vaccines, standardized the conjugation process and developed key assays required for routine lot release at production scale. Vi from a BSL1 organism, Citrobacter freundii, strain WR7011, was used as an alternative to Vi from S. Typhi. We showed that Vi conjugated to CRM(197), a non-toxic mutant of diphtheria toxin, widely used in commercial vaccines, was produced at high yield. Vi-CRM(197) proved immunogenic in animal studies, even without adjuvant. Thus, Vi-CRM(197) appears to be a suitable candidate for the development of a commercially viable, effective typhoid vaccine for developing countries. Copyright © 2010 Elsevier Ltd. All rights reserved.

The adsorption ability of Cr(VI) on sawdust–polyaniline nanocomposite

International Nuclear Information System (INIS)

Binh Phan, Thi; Que Do, Ngoc; Thanh Thuy Mai, Thi

2010-01-01

The results of this study of sawdust–polyaniline nanocomposite synthesized by a chemical method for Cr(VI) treatment in the environment are presented. Cr(VI) adsorption on a composite was determined by colorimetry. The results showed that sawdust–polyaniline composite synthesized with an aniline:sawdust ratio equal to 0.5 had an adsorption degree of 21.4 mg g −1 and adsorbed nearly 99% of the Cr(VI) after 2 h. The composite could be used for the adsorption of Cr(VI) from waste water. The Cr(VI) adsorption ability of the composite slightly depends on the pH value of the medium. The adsorption is fast during the first half hour and then the rate decreases

Testing of ENDF/B-VI data for shielding applications

International Nuclear Information System (INIS)

Ingersoll, D.T.

1995-01-01

Version VI of the U.S. Evaluated Nuclear Data File (END/B-VI) was released for open distribution in 1990 after an extensive multiyear, multilaboratory evaluation effort coordinated by the Cross Section Evaluation Working Group (CSEWG). More than 75 of the 320 evaluations contained in the library are new for Version VI, including many relatively important nuclides and many with substantial changes to the cross-section data. Also, several important changes were made to the basic data formats for Version VI to permit better representation of the data and to allow additional types of data. Although these format changes yielded improved evaluations, they hindered processing of the data for use in applications codes and delayed the timely integral testing of the data. It has been only during the past year that significant integral testing of END/B-VI data has been achieved. The results and conclusions from some of these efforts are summarized in the following paragraphs

Photoreduction of chromium(VI) in the presence of algae, Chlorella vulgaris

International Nuclear Information System (INIS)

Deng Lin; Wang Hongli; Deng Nansheng

2006-01-01

In this thesis, the photochemical reduction of hexavalent chromium Cr(VI) in the presence of algae, Chlorella vulgaris, was investigated under the irradiation of metal halide lamps (λ=365nm, 250W). The affecting factors of photochemical reduction were studied in detail, such as exposure time, initial Cr(VI) concentration, initial algae concentration and pH. The rate of Cr(VI) photochemical reduction increased with algae concentration increasing, exposure time increasing, initial Cr(VI) concentration decreasing and the decrease of pH. When pH increased to 6, the rate of Cr(VI) photochemical reduction nearly vanished. When initial Cr(VI) concentration ranged from 0.4 to 1.0mgL -1 and initial algae concentration ranged from ABS algae (the absorbency of algae)=0.025 to ABS algae =0.180, According to the results of kinetic analyses, the kinetic equation of Cr(VI) photochemical reduction in aqueous solution with algae under 250W metal halide lamps was V 0 =kC 0 0.1718 A algae 0.5235 (C 0 was initial concentration of Cr(VI); A algae was initial concentration of algae) under the condition of pH 4

Enhanced control and sensing for the REMOTEC ANDROS Mk VI robot. CRADA final report

International Nuclear Information System (INIS)

Spelt, P.F.; Harvey, H.W.

1998-01-01

This Cooperative Research and Development Agreement (CRADA) between Lockheed Martin Energy Systems, Inc., and REMOTEC, Inc., explored methods of providing operator feedback for various work actions of the ANDROS Mk VI teleoperated robot. In a hazardous environment, an extremely heavy workload seriously degrades the productivity of teleoperated robot operators. This CRADA involved the addition of computer power to the robot along with a variety of sensors and encoders to provide information about the robot's performance in and relationship to its environment. Software was developed to integrate the sensor and encoder information and provide control input to the robot. ANDROS Mk VI robots are presently used by numerous electric utilities to perform tasks in reactors where substantial exposure to radiation exists, as well as in a variety of other hazardous environments. Further, this platform has potential for use in a number of environmental restoration tasks, such as site survey and detection of hazardous waste materials. The addition of sensors and encoders serves to make the robot easier to manage and permits tasks to be done more safely and inexpensively (due to time saved in the completion of complex remote tasks). Prior research on the automation of mobile platforms with manipulators at Oak Ridge National Laboratory's Center for Engineering Systems Advanced Research (CESAR, B ampersand R code KC0401030) Laboratory, a BES-supported facility, indicated that this type of enhancement is effective. This CRADA provided such enhancements to a successful working teleoperated robot for the first time. Performance of this CRADA used the CESAR laboratory facilities and expertise developed under BES funding

Importance of c-Type cytochromes for U(VI reduction by Geobacter sulfurreducens

Directory of Open Access Journals (Sweden)

Leang Ching

2007-03-01

Full Text Available Abstract Background In order to study the mechanism of U(VI reduction, the effect of deleting c-type cytochrome genes on the capacity of Geobacter sulfurreducens to reduce U(VI with acetate serving as the electron donor was investigated. Results The ability of several c-type cytochrome deficient mutants to reduce U(VI was lower than that of the wild type strain. Elimination of two confirmed outer membrane cytochromes and two putative outer membrane cytochromes significantly decreased (ca. 50–60% the ability of G. sulfurreducens to reduce U(VI. Involvement in U(VI reduction did not appear to be a general property of outer membrane cytochromes, as elimination of two other confirmed outer membrane cytochromes, OmcB and OmcC, had very little impact on U(VI reduction. Among the periplasmic cytochromes, only MacA, proposed to transfer electrons from the inner membrane to the periplasm, appeared to play a significant role in U(VI reduction. A subpopulation of both wild type and U(VI reduction-impaired cells, 24–30%, accumulated amorphous uranium in the periplasm. Comparison of uranium-accumulating cells demonstrated a similar amount of periplasmic uranium accumulation in U(VI reduction-impaired and wild type G. sulfurreducens. Assessment of the ability of the various suspensions to reduce Fe(III revealed no correlation between the impact of cytochrome deletion on U(VI reduction and reduction of Fe(III hydroxide and chelated Fe(III. Conclusion This study indicates that c-type cytochromes are involved in U(VI reduction by Geobacter sulfurreducens. The data provide new evidence for extracellular uranium reduction by G. sulfurreducens but do not rule out the possibility of periplasmic uranium reduction. Occurrence of U(VI reduction at the cell surface is supported by the significant impact of elimination of outer membrane cytochromes on U(VI reduction and the lack of correlation between periplasmic uranium accumulation and the capacity for uranium

Cr(III) reactivity and foot dermatitis in Cr(VI) positive patients

DEFF Research Database (Denmark)

Hansen, Malene Barré; Menné, Torkil; Johansen, Jeanne Duus

2006-01-01

Chromium allergy has become synonymous with Cr(VI) allergy. However, real exposure to chromium from leather products may include both Cr(III) and Cr(VI). In this study, we investigate the reactivity to both Cr(VI) and Cr(III) in consecutive patients to analyse the relation between foot eczema/leather...... to Cr(III). The increased risk was not due to a higher degree of sensitivity to Cr(VI). Leather was reported most frequently as the suspected cause of chromium dermatitis (54%). However, Cr(VI) allergics having foot eczema and positive or doubtful Cr(III) reactions often had positive reactions to other...

Paul Scherrer Institute Scientific Report 1998. Volume VI: Large Research Facilities

Energy Technology Data Exchange (ETDEWEB)

Bauer, Guenter; Bercher, Renate; Buechli, Carmen; Foroughi, Fereydoun; Meyer, Rosa [eds.

1999-09-01

The department GFA (Grossforschungsanlagen, Large Research Facilities) has been established in October 1998 and its main duty is operation, maintenance and development of the PSI accelerators, the spallation neutron source and the beam transport systems for pions and muons. A large effort of this group concerns the planning and co-ordination of the assembly of the Swiss Light Source (SLS). (author) figs., tabs., refs.

An experimental study on the sorption of U(VI) onto granite

International Nuclear Information System (INIS)

Baik, Min Hoon; Hahn, Pil Soo

2002-01-01

The sorption of U(VI) on a domestic granite is studied as a function of experimental conditions such as contact time, solution-solid ratio, ionic strength, and pH using a batch procedure. The distribution coefficients, K d 's, of U(VI) are about 1-100mL/g depending on the experimental conditions. The sorption of U(VI) onto granite particles is greatly dependent upon the contact time, solution-solid ratio, and pH, but very little is dependent on the ionic strength. It is noticed that an U(VI)-carbonato ternary surface complex can be formed in the neutral range of pH. In the alkaline range of pH above 7, U(VI) sorption onto granite particles is greatly decreased due to the formation of anionic U(VI)-carbonato aqueous complexes

Simultaneous Cr(VI) bio-reduction and methane production by anaerobic granular sludge.

Science.gov (United States)

Hu, Qian; Sun, Jiaji; Sun, Dezhi; Tian, Lan; Ji, Yanan; Qiu, Bin

2018-08-01

Wastewater containing toxic hexavalent chromium (Cr(VI)) were treated with well-organized anaerobic granular sludge in this study. Results showed that the anaerobic granular sludge rapidly removed Cr(VI), and 2000 µg·L -1 Cr(VI) was completely eliminated within 6 min, which was much faster than the reported duration of removal by reported artificial materials. Sucrose added as a carbon source acted as an initial electron donor to reduce Cr(VI) to Cr(III). This process was considered as the main mechanism of Cr(VI) removal. Methane production by anaerobic granular sludge was improved by the addition of Cr(VI) at a concentration lower than 500 µg·L -1 . Anaerobic granular sludge had a well-organized structure, which presented good resistance against toxic Cr(VI). Trichoccus accelerated the degradation of organic substances to generate acetates with a low Cr(VI) concentration, thereby enhancing methane production by acetotrophic methanogens. Copyright © 2018 Elsevier Ltd. All rights reserved.

Re-examination of immune response and estimation of anti-Vi IgG protective threshold against typhoid fever-based on the efficacy trial of Vi conjugate in young children.

Science.gov (United States)

Szu, Shousun C; Klugman, Keith P; Hunt, Steven

2014-04-25

The capsular polysaccharide of Salmonella enterica serovar Typhi, Vi antigen, is an essential virulence factor and a protective antigen. Similar to other polysaccharide vaccines, the protective action of Vi, both to the polysaccharide alone or when presented as a conjugate, is mediated by serum IgG Vi antibodies. The evaluation of Vi capsular polysaccharide based vaccines to prevent typhoid fever would be significantly facilitated by the identification of a "protective level" of serum antibodies to Vi antigen. The protective level of anti-Vi IgG against typhoid fever was derived from the protective efficacy and immune response of a Vi-rEPA conjugate vaccine efficacy trial. The estimation was derived by two methods: correlation of the percent efficacy and the antibody distribution profile in the vaccine group at a given period of observation, and use of the relative ratio of anti-Vi IgG levels between the vaccine and placebo groups greater or equal to the Relative Risk of typhoid fever used in the efficacy determination. Both methods predicted a similar range of a minimum protective level of anti-Vi IgG between 1.4 and 2.0μg/ml (short term threshold). When applying a protective threshold of 10μg/ml at 6 months post immunization, an IgG level in excess of 1.4μg/ml was achieved by 90% of children at 46 months post immunization, consistent with an 89% level of protection over the duration of the study. We thus suggest that the proportion of children with Vi IgG>10μg/ml (long term threshold) 6 months after immunization may reflect the proportion protected over at least a 4 year period. The current assignment of an anti-Vi IgG protective level may be of value when evaluating vaccine performance of future Vi conjugate vaccines. Published by Elsevier Ltd.

Factors affecting the adsorption of chromium (VI) on activated carbon

Energy Technology Data Exchange (ETDEWEB)

Yavuz, R.; Orbak, I.; Karatepe, N. [Istanbul Technical University, Istanbul (Turkey)

2006-09-15

The aim of this investigation was to determine the adsorption behavior of chromium (VI) on two different activated carbon samples produced from Tuncbilek lignite. The effects of the initial chromium (VI) concentration (250-1000 mg/L), temperature (297-323 K) and pH (2.0-9.5) on adsorption were investigated systematically. The effectiveness of the parameters on chromium adsorption was found to be in the order of pH, the initial Cr(VI) concentration and the temperature. Increasing the pH from 2.0 to 9.5 caused a decrease in adsorption. However, the adsorption was increased by increasing the initial Cr(VI) concentration and temperature. The multilinear mathematical model was also developed to predict the Cr(VI) adsorption on activated carbon samples within the experimental conditions.

Simultaneous removal of Cr(VI) and 4-chlorophenol through photocatalysis by a novel anatase/titanate nanosheet composite: Synergetic promotion effect and autosynchronous doping

International Nuclear Information System (INIS)

Liu, Wen; Sun, Weiling; Borthwick, Alistair G.L.; Wang, Ting; Li, Fan; Guan, Yidong

2016-01-01

Highlights: • TNS composed of anatase and titanate synthesized via a facile one-step method. • Cr(VI) and 4-CP can be simultaneously removed by TNS through photocatalysis. • Photocatalytic efficiencies of Cr(VI) and 4-CP greatly enhanced when coexisting. • Synergetic promotion effect occurs due to separation of electron-hole pairs. • Autosynchronous doping after Cr(III) adsorption leads to narrowed energy gap. - Abstract: Clean-up of wastewaters with coexisting heavy metals and organic contaminants is a huge issue worldwide. In this study, a novel anatase/titanate nanosheet composite material (labeled as TNS) synthesized through a one-step hydrothermal reaction was demonstrated to achieve the goal of simultaneous removal of Cr(VI) and 4-cholophenol (4-CP) from water. TEM and XRD analyses indicated the TNS was a nano-composite of anatase and titanate, with anatase acting as the primary photocatalysis center and titanate as the main adsorption site. Enhanced photocatalytic removal of co-existent Cr(VI) and 4-CP was observed in binary systems, with apparent rate constants (k_1) for photocatalytic reactions of Cr(VI) and 4-CP about 3.1 and 2.6 times of that for single systems. In addition, over 99% of Cr(VI) and 4-CP was removed within 120 min through photocatalysis by TNS at pH 7 in the binary system. Mechanisms for enhanced photocatalytic efficiency in the binary system are identified as: (1) a synergetic effect on the photo-reduction of Cr(VI) and photo-oxidation of 4-CP due to efficient separation of electron-hole pairs, and (2) autosynchronous doping because of reduced Cr(III) adsorption onto TNS. Furthermore, TNS could be efficiently reused after a simple acid-base treatment.

Simultaneous removal of Cr(VI) and 4-chlorophenol through photocatalysis by a novel anatase/titanate nanosheet composite: Synergetic promotion effect and autosynchronous doping

Energy Technology Data Exchange (ETDEWEB)

Liu, Wen, E-mail: wzl0025@auburn.edu [Jiangsu Key Laboratory of Atmospheric Environment Monitoring and Pollution Control, School of Environmental Science and Engineering, Nanjing University of Information Science and Technology, Nanjing 210044 (China); The Key Laboratory of Water and Sediment Sciences, Ministry of Education, Department of Environmental Engineering, Peking University, Beijing 100871 (China); Environmental Engineering Program, Department of Civil Engineering, Auburn University, Auburn, AL 36849 (United States); Sun, Weiling [The Key Laboratory of Water and Sediment Sciences, Ministry of Education, Department of Environmental Engineering, Peking University, Beijing 100871 (China); Borthwick, Alistair G.L. [School of Engineering, The University of Edinburgh, The King’s Buildings, Edinburgh EH9 3JL (United Kingdom); Wang, Ting [The Key Laboratory of Water and Sediment Sciences, Ministry of Education, Department of Environmental Engineering, Peking University, Beijing 100871 (China); Li, Fan [Environmental Engineering Program, Department of Civil Engineering, Auburn University, Auburn, AL 36849 (United States); Guan, Yidong, E-mail: yidongguan@nuist.edu.cn [Jiangsu Key Laboratory of Atmospheric Environment Monitoring and Pollution Control, School of Environmental Science and Engineering, Nanjing University of Information Science and Technology, Nanjing 210044 (China); Environmental Engineering Program, Department of Civil Engineering, Auburn University, Auburn, AL 36849 (United States)

2016-11-05

Highlights: • TNS composed of anatase and titanate synthesized via a facile one-step method. • Cr(VI) and 4-CP can be simultaneously removed by TNS through photocatalysis. • Photocatalytic efficiencies of Cr(VI) and 4-CP greatly enhanced when coexisting. • Synergetic promotion effect occurs due to separation of electron-hole pairs. • Autosynchronous doping after Cr(III) adsorption leads to narrowed energy gap. - Abstract: Clean-up of wastewaters with coexisting heavy metals and organic contaminants is a huge issue worldwide. In this study, a novel anatase/titanate nanosheet composite material (labeled as TNS) synthesized through a one-step hydrothermal reaction was demonstrated to achieve the goal of simultaneous removal of Cr(VI) and 4-cholophenol (4-CP) from water. TEM and XRD analyses indicated the TNS was a nano-composite of anatase and titanate, with anatase acting as the primary photocatalysis center and titanate as the main adsorption site. Enhanced photocatalytic removal of co-existent Cr(VI) and 4-CP was observed in binary systems, with apparent rate constants (k{sub 1}) for photocatalytic reactions of Cr(VI) and 4-CP about 3.1 and 2.6 times of that for single systems. In addition, over 99% of Cr(VI) and 4-CP was removed within 120 min through photocatalysis by TNS at pH 7 in the binary system. Mechanisms for enhanced photocatalytic efficiency in the binary system are identified as: (1) a synergetic effect on the photo-reduction of Cr(VI) and photo-oxidation of 4-CP due to efficient separation of electron-hole pairs, and (2) autosynchronous doping because of reduced Cr(III) adsorption onto TNS. Furthermore, TNS could be efficiently reused after a simple acid-base treatment.

Analytical applications of N-phenyl-n-butyro hydroxamic and N-p-tolyl-n-butyro hydroxamic acids towards chromium (VI), copper (II), iron (III) and uranium (VI)

International Nuclear Information System (INIS)

Elkhadir, A. Y. F.

2001-05-01

Two aliphatic hydroxamic acids were prepared; N-phenyl-n-butyro hydroxamic acid and N-p-tolyl-n-butyro hydroxamic acid, by the reaction of β-phenylhydroxylamine and p-tolyl hydroxylamine with n-butyryl chloride. The acids were identified by: their melting points, characteristic reactions with acidic solutions of vanadium (V) and iron (III), infrared spectroscopy, nitrogen content and molecular weight determination. The extractability of these acids towards Cr (VI), Cu (II), Fe (III) and U (VI) were investigated at different pH values and molar acid concentrations. N-phenyl-n- butyro hydroxamic acid has a maximum extraction (98.80%) for Cr (VI) at 4 M H 2 SO 4 , (83.25%) for Cu (II) at pH 6, (99.17%) for Fe (III) at pH 5 and (99.76%) at 4 M HNO 3 for U (VI) respectively. N-p-tolyl-n-butyro hydroxamic acid has a maximum extraction (98.40%) for Cr (VI)at 4 M H 2 SO 4 , (81.30%) for Cu (II) at pH 6, (92.80%) for Fe (III) at pH 5 and (99.64%) for U (VI) at 4 M HNO 3 , respectively. The ratios of the metal to ligands were determined by job method (continuous variation method) and were found to be 1:2 for Cr (VI) and U (VI). (Author)

Analytical applications of N-phenyl-n-butyro hydroxamic and N-p-tolyl-n-butyro hydroxamic acids towards chromium (VI), copper (II), iron (III) and uranium (VI)

Energy Technology Data Exchange (ETDEWEB)

Elkhadir, A Y. F. [Department of Chemistry, Faculty of Science, University of Khartoum, Khartoum (Sudan)

2001-05-01

Two aliphatic hydroxamic acids were prepared; N-phenyl-n-butyro hydroxamic acid and N-p-tolyl-n-butyro hydroxamic acid, by the reaction of {beta}-phenylhydroxylamine and p-tolyl hydroxylamine with n-butyryl chloride. The acids were identified by: their melting points, characteristic reactions with acidic solutions of vanadium (V) and iron (III), infrared spectroscopy, nitrogen content and molecular weight determination. The extractability of these acids towards Cr (VI), Cu (II), Fe (III) and U (VI) were investigated at different pH values and molar acid concentrations. N-phenyl-n- butyro hydroxamic acid has a maximum extraction (98.80%) for Cr (VI) at 4 M H{sub 2}SO{sub 4}, (83.25%) for Cu (II) at pH 6, (99.17%) for Fe (III) at pH 5 and (99.76%) at 4 M HNO{sub 3} for U (VI) respectively. N-p-tolyl-n-butyro hydroxamic acid has a maximum extraction (98.40%) for Cr (VI)at 4 M H{sub 2} SO{sub 4}, (81.30%) for Cu (II) at pH 6, (92.80%) for Fe (III) at pH 5 and (99.64%) for U (VI) at 4 M HNO{sub 3}, respectively. The ratios of the metal to ligands were determined by job method (continuous variation method) and were found to be 1:2 for Cr (VI) and U (VI). (Author)

Photoreduction of chromium(VI) in the presence of algae, Chlorella vulgaris

Energy Technology Data Exchange (ETDEWEB)

Deng Lin [School of Resources and Environmental Science, Wuhan University, Wuhan 430072 (China); Wang Hongli [School of Resources and Environmental Science, Wuhan University, Wuhan 430072 (China); Deng Nansheng [School of Resources and Environmental Science, Wuhan University, Wuhan 430072 (China)]. E-mail: nsdengwhu@163.com

2006-11-16

In this thesis, the photochemical reduction of hexavalent chromium Cr(VI) in the presence of algae, Chlorella vulgaris, was investigated under the irradiation of metal halide lamps ({lambda}=365nm, 250W). The affecting factors of photochemical reduction were studied in detail, such as exposure time, initial Cr(VI) concentration, initial algae concentration and pH. The rate of Cr(VI) photochemical reduction increased with algae concentration increasing, exposure time increasing, initial Cr(VI) concentration decreasing and the decrease of pH. When pH increased to 6, the rate of Cr(VI) photochemical reduction nearly vanished. When initial Cr(VI) concentration ranged from 0.4 to 1.0mgL{sup -1} and initial algae concentration ranged from ABS{sub algae} (the absorbency of algae)=0.025 to ABS{sub algae}=0.180, According to the results of kinetic analyses, the kinetic equation of Cr(VI) photochemical reduction in aqueous solution with algae under 250W metal halide lamps was V{sub 0}=kC{sub 0}{sup 0.1718}A{sub algae}{sup 0.5235} (C{sub 0} was initial concentration of Cr(VI); A{sub algae} was initial concentration of algae) under the condition of pH 4.

CoQ10 Deficiency May Indicate Mitochondrial Dysfunction in Cr(VI Toxicity

Directory of Open Access Journals (Sweden)

Xiali Zhong

2017-04-01

Full Text Available To investigate the toxic mechanism of hexavalent chromium Cr(VI and search for an antidote for Cr(VI-induced cytotoxicity, a study of mitochondrial dysfunction induced by Cr(VI and cell survival by recovering mitochondrial function was performed. In the present study, we found that the gene expression of electron transfer flavoprotein dehydrogenase (ETFDH was strongly downregulated by Cr(VI exposure. The levels of coenzyme 10 (CoQ10 and mitochondrial biogenesis presented by mitochondrial mass and mitochondrial DNA copy number were also significantly reduced after Cr(VI exposure. The subsequent, Cr(VI-induced mitochondrial damage and apoptosis were characterized by reactive oxygen species (ROS accumulation, caspase-3 and caspase-9 activation, decreased superoxide dismutase (SOD and ATP production, increased methane dicarboxylic aldehyde (MDA content, mitochondrial membrane depolarization and mitochondrial permeability transition pore (MPTP opening, increased Ca2+ levels, Cyt c release, decreased Bcl-2 expression, and significantly elevated Bax expression. The Cr(VI-induced deleterious changes were attenuated by pretreatment with CoQ10 in L-02 hepatocytes. These data suggest that Cr(VI induces CoQ10 deficiency in L-02 hepatocytes, indicating that this deficiency may be a biomarker of mitochondrial dysfunction in Cr(VI poisoning and that exogenous administration of CoQ10 may restore mitochondrial function and protect the liver from Cr(VI exposure.

As duas naturezas de Lévi-Strauss

Directory of Open Access Journals (Sweden)

Philippe Descola

2011-11-01

Full Text Available Aborda-se aqui a complexidade do status do par conceitual natureza e cultura no pensamento de Lévi-Strauss. Ao mesmo tempo ferramenta de análise, cena filosófica dos primórdios e antinomia a superar, revisita-se os diferentes usos e significados na obra de Lévi-Strauss do conceito de natureza e sua relação com o de cultura. Mostra-se como é possível reconhecer na obra de Lévi-Strauss dois conceitos de natureza: por um lado, uma natureza que se opõe à cultura num programa científico formulado em termos classicamente dualistas e, por outro, uma teoria do conhecimento decididamente monista que considera o espírito como parte e produto desse mesmo mundo. Argumenta-se que se o dualismo entre cultura e natureza fundou o pensamento estruturalista de Lévi-Strauss, é na própria obra deste que encontramos os argumentos e meios de superá-lo. A vocação do estruturalismo na antropologia de hoje, no entanto, é de ir mais longe neste caminho do que foi o próprio fundador.

Procedure for plutonium determination using Pu(VI) spectra

International Nuclear Information System (INIS)

Walker, L.F.; Temer, D.J.; Jackson, D.D.

1996-01-01

This document describes a simple spectrophotometric method for determining total plutonium in nitric acid solutions based on the spectrum of Pu(VI). Plutonium samples in nitric acid are oxidized to Pu(VI) with Ce(IV) and the net absorbance at the 830 nm peak is measured

Wind tunnel test of musi VI bridge

Science.gov (United States)

Permata, Robby; Andika, Matza Gusto; Syariefatunnisa, Risdhiawan, Eri; Hermawan, Budi; Noordiana, Indra

2017-11-01

Musi VI Bridge is planned to cross the Musi River in Palembang City, South Sumatera Province, Indonesia. The main span is a steel arch type with 200 m length and side span length is 75 m. Finite element analysis results showed that the bridge has frequency ratio for torsional and heaving mode (torsional frequency/heaving frequency)=1.14. This close to unity value rises concern about aerodynamic behaviour and stability of the bridge deck under wind loading. Sectional static and free vibration wind tunnel test were performed to clarify this phenomena in B2TA3 facility in Serpong, Indonesia. The test followed the draft of Guide of Wind Tunnel Test for Bridges developed by Indonesian Ministry of Public Works. Results from wind tunnel testing show that the bridge is safe from flutter instability and no coupled motion vibration observed. Therefore, low value of frequency ratio has no effect to aerodynamic behaviour of the bridge deck. Vortex-induced vibration in heaving mode occurred in relatively low wind velocity with permissible maximum amplitude value.

Surface enrichment with chrome and nitriding of IF steel under an abnormal glow discharge; Enriquecimento superficial com cromo e nitretacao do aco IF em descarga eletrica em regime anormal

Energy Technology Data Exchange (ETDEWEB)

Meira, S.R.; Borges, P.C., E-mail: sabrina.r.meira@gmail.com [Universidade Tecnologica Federal do Parana (UTFPR), Curitiba, PR (Brazil). Grupo de Materiais; Bernardelli, E.A. [Instituto Federal do Parana (IFPR), Paranagua, PR (Brazil). Laboratorio de Materiais

2014-07-01

The objective of this work is to evaluate the influence of surface enrichment of IF steel with chrome, and nitriding, the formation of the nitrided layer. Thus, IF steel samples were subjected to surface enrichment process, using 409 stainless steel as a target for sputtering, followed by plasma nitriding, both under a dc abnormal glow discharge. The enrichment treatment was operated at 1200 ° C for 3h. The nitriding treatment was operated at 510 ° C for 2 h. The influence of the treatments on the layers formed was studied through optical microscopy (OM), scan electron microscopy (SEM), X-ray diffraction (XRD) and Vickers microindentation. The results show that the enrichment is effective to enrich the IF surface, furthermore, improves the characteristics of nitriding, comparing nitriding samples to nitriding and enriched, was observed needles of nitrides, as well as a higher hardness, which is associated with the nitrides of chrome, on the nitriding and enriched samples. (author)

Cr(VI) reduction and immobilization by novel carbonaceous modified magnetic Fe{sub 3}O{sub 4}/halloysite nanohybrid

Energy Technology Data Exchange (ETDEWEB)

Tian, Xike, E-mail: xktian@cug.edu.cn [Faculty of Material Science and Chemistry, China University of Geosciences, Wuhan 430074 (China); Wang, Weiwei; Tian, Na; Zhou, Chaoxin; Yang, Chao [Faculty of Material Science and Chemistry, China University of Geosciences, Wuhan 430074 (China); Komarneni, Sridhar [Materials Research Laboratory, Materials Research Institute and Department of Ecosystem Science and Management, The Pennsylvania State University, University Park, PA 16802 (United States)

2016-05-15

Highlights: • A novel magnetic nonohybrids (Fe{sub 3}O{sub 4}/HNTs@C) were synthesized for Cr(VI) removal. • Cr(VI) was reduced to Cr(III) by Fe{sub 3}O{sub 4} nanoparticles and hydroxyl groups. • Cr ions were attached on Fe{sub 3}O{sub 4}/HNTs@C by ion exchange and coordination interaction. - Abstract: In this work, a novel “Dumbbell-like” magnetic Fe{sub 3}O{sub 4}/Halloysite nanohybrid (Fe{sub 3}O{sub 4}/HNTs@C) with oxygen-containing organic group grafting on the surface of natural halloysite nanotubes (HNTs) and homogeneous Fe{sub 3}O{sub 4} nanospheres selectively aggregating at the tips of modified halloysite nanotubes was successfully synthesized. XRD, TEM, IR spectroscopy, XPS and VSM were used to characterize this newly halloysite nanohybrid and its formation mechanism was discussed. Cr(VI) ions adsorption experiments showed that the Fe{sub 3}O{sub 4}/halloysite nanohybrid exhibited higher adsorption ability with a maximum adsorption capacity of 132 mg/L at 303 K, which is about 100 times higher than that of unmodified halloysite nanotubes. More importantly, with the reduction of Fe{sub 3}O{sub 4} and electron–donor effect of oxygen-containing organic groups, Cr(VI) ions were easily reduced into low toxicity Cr(III) and then adsorbed onto the surface of halloysite nanohybrid. In addition, appreciable magnetization was observed due to the aggregation of magnetite nanoparticles, which make adsorbent facility separated from aqueous solutions after Cr pollution adsorption.

PHOTOCATALYTIC REMOVAL OF TR I- AND HEXA-VALENT CHROMIUM IONS FROM CHROME-ELECTROPL ATING WASTEWATER

Directory of Open Access Journals (Sweden)

Puangrat Kajitvichyanukul

2017-11-01

Full Text Available A novel technique based on photocatalysis was applied to eliminate chromium ions, a toxic hazardous environmental pollutant. The photoreduction of each species of chromium (total, hexavalent, and trivalent chromiums from chrome-electroplating wastewater was investigated using a titanium dioxide suspension under irradiation by a low-pressure mercury lamp. The initial concentration of total chromium was 300 mg/l. The applied conditions were the direct photocatalytic reduction process at pH 3.65 and the indirect photocatalytic reduction with added hole scavengers at the same solution pH. Results from both processes were comparatively discussed. Result show that chromium was not efficiently removed by direct photoreduction. In contrast, with the adding of hole scavengers, which were formate ions, the photoreduction of chromium was very favorable. Both hexavalent and trivalent chromiums were efficiently removed. The photocatalytic mechanism is purposed in this study.

Spectrophotometric determination of zirconium with Chrome Azurol s in aqueous streams of nuclear fuel reprocessing

International Nuclear Information System (INIS)

Ganesh, S.; Velavendan, P.; Pandey, N.K.; Kamachi Mudali, U.; Natarajan, R.

2014-01-01

A sensitive and reproducible spectrophotometric method for the determination of zirconium is developed. The method is based on the formation of stable bluish violet colour complex with Chrome Azurol S (CAS) with maximum absorption at 598 nm. The complex formed obeys Beer's law in the range of 1-7 μg/mL. Under optimum conditions, the sensitivity of the proposed method, (i.e. the detection limit), molar absorptivity and Sandell's sensitivity values are 2.42 μg/mL, 3.93 x10 3 L.Mol -1 .cm -1 and 2.54 x 10 -4 μg/cm 2 respectively. Relative standard deviation is less than 2% and correlation coefficient is 0.997. The present method is highly sensitive, selective, rapid and simple. It can be applied for the direct determination of zirconium in environmental, industrial, water and nuclear reprocessing samples. (author)

Modelling Cr(VI) removal by a combined carbon-activated sludge system

International Nuclear Information System (INIS)

Orozco, A. Micaela Ferro; Contreras, Edgardo M.; Zaritzky, Noemi E.

2008-01-01

The combined carbon-activated sludge process has been proposed as an alternative to protect the biomass against toxic substances in wastewaters; however, the information about the effect of powdered-activated carbon (PAC) addition in activated sludge reactors for the treatment of wastewaters containing Cr(VI) is limited. The objectives of the present study were: (a) to evaluate the removal of hexavalent chromium by (i) activated sludge microorganisms in aerobic batch reactors, (ii) powdered-activated carbon, and (iii) the combined action of powdered-activated carbon and biomass; (b) to propose mathematical models that interpret the experimental results. Different Cr(VI) removal systems were tested: (S1) biomass (activated sludge), (S2) PAC, and (S3) the combined activated carbon-biomass system. A Monod-based mathematical model was used to describe the kinetics of Cr(VI) removal in the system S1. A first-order kinetics with respect to Cr(VI) and PAC respectively, was proposed to model the removal of Cr(VI) in the system S2. Cr(VI) removal in the combined carbon-biomass system (S3) was faster than both Cr(VI) removal using PAC or activated sludge individually. Results showed that the removal of Cr(VI) using the activated carbon-biomass system (S3) was adequately described by combining the kinetic equations proposed for the systems S1 and S2

A CMOS rail-to-rail linear VI-converter

NARCIS (Netherlands)

Vervoort, P.P.; Vervoort, P.P.; Wassenaar, R.F.

1995-01-01

A linear CMOS VI-converter operating in strong inversion with a common-mode input range from the negative to the positive supply rail is presented. The circuit consists of three linear VI-converters based on the difference of squares principle. Two of these perform the actual V to I conversion,

Ternary uranium(VI) carbonato humate complex studied by cryo-TRLFS

International Nuclear Information System (INIS)

Steudtner, R.; Sachs, S.; Schmeide, K.; Brendler, V.; Bernhard, G.

2011-01-01

The complex formation of U(VI) with humic acid (HA) in the presence of carbonate was studied by time-resolved laser-induced fluorescence spectroscopy at low temperature (cryo-TRLFS) at pH 8.5. In the presence of HA, a decrease of the luminescence intensity of U(VI) and no shift of the emission band maxima in comparison to the luminescence spectrum of the UO 2 (CO 3 ) 3 4- complex, the dominating U(VI) species under the applied experimental conditions in the absence of HA, was observed. The formation of a ternary U(VI) carbonato humate complex of the type UO 2 (CO 3 ) 2 HA(II) 4- starting from UO 2 (CO 3 ) 3 4- was concluded from the luminescence data. For this complex a complex stability constant of log K=2.83 ± 0.17 was determined. Slope analysis resulted in a slope of 1.12 ± 0.11, which verifies the postulated complexation reaction. The results agree very well with literature data. Speciation calculations show that the formation of the ternary U(VI) carbonato humate complex can significantly influence the U(VI) speciation under environmental conditions. (orig.)

THE SURPRISINGLY CONSTANT STRENGTH OF O VI ABSORBERS OVER COSMIC TIME

International Nuclear Information System (INIS)

Fox, Andrew J.

2011-01-01

O VI absorption is observed in a wide range of astrophysical environments, including the local interstellar medium, the disk and halo of the Milky Way, high-velocity clouds, the Magellanic Clouds, starburst galaxies, the intergalactic medium (IGM), damped Lyα systems, and gamma-ray-burst host galaxies. Here, a new compilation of 775 O VI absorbers drawn from the literature is presented, all observed at high resolution (instrumental FWHM ≤ 20 km s -1 ) and covering the redshift range z = 0-3. In galactic environments [log N(H I) ∼> 20], the mean O VI column density is shown to be insensitive to metallicity, taking a value log N(O VI) ∼ 14.5 for galaxies covering the range -1.6 ∼ 4 K) clouds and hot (∼10 6 K) plasma, although many such layers would have to be intersected by a typical galaxy-halo sight line to build up the characteristic galactic N(O VI). The alternative, widely used model of single-phase photoionization for intergalactic O VI is ruled out by kinematic evidence in the majority of IGM O VI components at low and high redshift.

Reduction of trace quantities of chromium(VI by strong acids

Directory of Open Access Journals (Sweden)

Pezzin Sérgio H

2004-01-01

Full Text Available The chemical behavior of Cr(VI at low concentrations (10-4 to 10-7 mol L-1 in several strong acids was studied using high specific activity 51Cr(VI as a tracer. The speciation of the products from these systems was carried out by ion exchange chromatography with stepwise elution. The results show that trace quantities of Cr(VI, monitored by means of radiochromium (51Cr, are reduced in the presence of mineral acids such as perchloric, hydrochloric, hydrofluoric, sulfuric, nitric and trifluoromethanesulfonic acids, even in the absence of conventional reducing agents, producing different measureable Cr(III species, depending on the acid anion. Detailed studies of the reduction of low concentrations of Cr(VI with nitric acid have shown that the relative rate of reduction increases as the concentration of the acid increases or as the concentration of the Cr(VI decreases.

Estudio de inmunogenicidad de la vacuna antitifoídica cubana de polisacárido Vi vax-TyVi® en ratones

Directory of Open Access Journals (Sweden)

Juan Carlos Ramírez

2006-08-01

Full Text Available Salmonella enterica serovar Typhi es un microorganismo que provoca más de 16 millones de casos de fiebre tifoidea con aproximadamente 600 000 muertes al año en todo el mundo. Dentro de las vacunas antitifoídicas la de polisacárido capsular Vi ha encontrado, gracias a sus incuestionables ventajas, una gran aceptación entre productores y consumidores. El presente trabajo aborda el estudio de inmunogenicidad de la vacuna antitifoídica cubana de polisacárido Vi vax-TyViâ en ratones. El estudio estuvo conformado por un grupo control no inoculado y un segundo grupo que recibió 0,05 mL de la vacuna por vía intramuscular. Se tomaron muestras de sangre a los -3, 7, 14, 21, 28, 42, 56 y 84 días. La actividad de anticuerpos IgG antipolisacárido Vi de los sueros individuales fue determinada por ELISA. Los datos fueron analizados por grupo y por sexo y se calculó el porcentaje de seroconversión, considerándose respondedor aquel animal que al menos aumentara en cuatro veces su título inicial. La respuesta de anticuerpos inducida por la vacuna mostró un aumento notable de los títulos de IgG antipolisacárido Vi en el grupo vacunado (100% de seroconversión, mientras que el grupo control no incrementó sus niveles mínimos iniciales (0% de respondedores. Aunque más dispersa, la respuesta de anticuerpos antiVi fue significativamente mayor en las hembras que en los machos.

Synthesis, structure and properties of oxo- and dioxochloride complexes of molybdenum(VI) and tungsten(VI) with 8-oxyquinoline

International Nuclear Information System (INIS)

Abramenko, V.L.; Sergienko, V.S.; Egorova, O.A.

2005-01-01

Complexes of oxo- and dioxochlorides of molybdenum(VI) and tungsten(VI) with 8-oxyquinoline of molecular and intracomplex type are synthesized and studied by the method of IR spectroscopy. The complexes have octahedral structure. It is proposed that 8-oxyquinoline in molecular complexes is coordinated by central atom through nitrogen atom of heterocycle, but in intracomplex compounds - through heterocyclic nitrogen atom and oxygen atom of deprotonated OH-group. Thermal stability of the complexes is studied [ru

Quantifying Cr(VI) Production and Export from Serpentine Soil of the California Coast Range.

Science.gov (United States)

McClain, Cynthia N; Fendorf, Scott; Webb, Samuel M; Maher, Kate

2017-01-03

Hexavalent chromium (Cr(VI)) is generated in serpentine soils and exported to surface and groundwaters at levels above health-based drinking water standards. Although Cr(VI) concentrations are elevated in serpentine soil pore water, few studies have reported field evidence documenting Cr(VI) production rates and fluxes that govern Cr(VI) transport from soil to water sources. We report Cr speciation (i) in four serpentine soil depth profiles derived from the California Coast Range serpentinite belt and (ii) in local surface waters. Within soils, we detected Cr(VI) in the same horizons where Cr(III)-minerals are colocated with biogenic Mn(III/IV)-oxides, suggesting Cr(VI) generation through oxidation by Mn-oxides. Water-extractable Cr(VI) concentrations increase with depth constituting a 7.8 to 12 kg/km 2 reservoir of Cr(VI) in soil. Here, Cr(VI) is produced at a rate of 0.3 to 4.8 kg Cr(VI)/km 2 /yr and subsequently flushed from soil during water infiltration, exporting 0.01 to 3.9 kg Cr(VI)/km 2 /yr at concentrations ranging from 25 to 172 μg/L. Although soil-derived Cr(VI) is leached from soil at concentrations exceeding 10 μg/L, due to reduction and dilution during transport to streams, Cr(VI) levels measured in local surface waters largely remain below California's drinking water limit.

Nucleotide sequence of the 3' ends of the double-stranded RNAs of grapevine chrome mosaic nepovirus.

Science.gov (United States)

Le Gall, O; Candresse, T; Dunez, J

1988-02-01

Attempts were made to label the termini of dsRNAs corresponding to the two genomic RNAs of grapevine chrome mosaic nepovirus (GCMV). It was not possible to label the 5' ends of the dsRNAs with [gamma-32P]ATP, which suggests that a genome-linked protein blocks their 5' ends. Both dsRNA species were labelled at their 3' ends with pCp. The 3'-terminal sequences were determined by 'wandering spot' or by partial enzymic cleavage analysis. One strand (presumably positive) ended in a poly(A) 30 to 50 nucleotides long whereas the other (presumably negative) ended in 3'-ACCUUUUAAAAAG (RNA1) or 3'-ACCUUUUAAUAAAG (RNA2). The sequences resemble closely those complementary to the 5' ends of the RNAs of tomato black ring virus (strain S), which is distantly related to GCMV.

Emission during the firing of chrome-magnesite products in tunnel kilns

Energy Technology Data Exchange (ETDEWEB)

Krechin, Yu.V.; Telegin, S.V.; Ivanov, N.M.; Kasimov, A.M.; Plichko, E.P.; Sverkov, Yu.M.; Maksimov, B.N.

1986-11-01

When chrome-magnesite products are fired in tunnel furnaces, the concentration in the effluent gas of dust is 110-150; of Cr/sub 7/O/sub 3/, 5-7; NO/sub x/, 20-35; CO, 100-125; SO/sub 2/, 25-40; and SO/sub 3/, 30-70 mg/m/sup 3/. The emission dust is finely dispersed. The average size of the particles of dust is 0.3, the minimum 0.05, and the maximum 1 ..mu..m. There is no hydrogen sulfide, NO/sub 2/, or CrO/sub 3/ in the emission. Dust and nitrogen oxides are formed in the firing zone of the kiln. The formation of dust and NO/sub 2/ depends on the air-consumption coefficient. The use of the pipe-in-pipe type of ports does not provide good gas combustion. To improve the operation of the kiln and the combustion of the natural gas it is recommended that instead of the obsolescent tube-in-tube ports, the ports developed by the Eastern Institute of Refractories be installed since they have given good results in tests. To improve the scattering effect of the removal of dust in the existing equipment it is recommended that the height of the flue stacks be increased to 40-50 m.

Chromium (VI) biosorption properties of multiple resistant bacteria isolated from industrial sewerage.

Science.gov (United States)

Oyetibo, Ganiyu Oladunjoye; Ilori, Matthew Olusoji; Obayori, Oluwafemi Sunday; Amund, Olukayode Oladipo

2013-08-01

Chromium (VI) [Cr (VI)] biosorption by four resistant autochthonous bacterial strains was investigated to determine their potential for use in sustainable marine water-pollution control. Maximum exchange between Cr (VI) ions and protons on the cells surfaces were at 30-35 °C, pH 2.0 and 350-450 mg/L. The bacterial strains effectively removed 79.0-90.5 % Cr (VI) ions from solution. Furthermore, 85.3-93.0 % of Cr (VI) ions were regenerated from the biomasses, and 83.4-91.7 % of the metal was adsorbed when the biomasses was reused. Langmuir isotherm performed better than Freundlich isotherm, depicting that Cr (VI) affinity was in the sequence Rhodococcus sp. AL03Ni > Burkholderia cepacia AL96Co > Corynebacterium kutscheri FL108Hg > Pseudomonas aeruginosa CA207Ni. Biosorption isotherms confirmed that Rhodococcus sp. AL03Ni was a better biosorbent with a maximum uptake of 107.46 mg of Cr (VI) per g (dry weight) of biomass. The results highlight the high potential of the organisms for bacteria-based detoxification of Cr (VI) via biosorption.

Mucopolysaccharidosis VI

Directory of Open Access Journals (Sweden)

Harmatz Paul

2010-04-01

Full Text Available Abstract Mucopolysaccharidosis VI (MPS VI is a lysosomal storage disease with progressive multisystem involvement, associated with a deficiency of arylsulfatase B leading to the accumulation of dermatan sulfate. Birth prevalence is between 1 in 43,261 and 1 in 1,505,160 live births. The disorder shows a wide spectrum of symptoms from slowly to rapidly progressing forms. The characteristic skeletal dysplasia includes short stature, dysostosis multiplex and degenerative joint disease. Rapidly progressing forms may have onset from birth, elevated urinary glycosaminoglycans (generally >100 μg/mg creatinine, severe dysostosis multiplex, short stature, and death before the 2nd or 3rd decades. A more slowly progressing form has been described as having later onset, mildly elevated glycosaminoglycans (generally ARSB gene, located in chromosome 5 (5q13-5q14. Over 130 ARSB mutations have been reported, causing absent or reduced arylsulfatase B (N-acetylgalactosamine 4-sulfatase activity and interrupted dermatan sulfate and chondroitin sulfate degradation. Diagnosis generally requires evidence of clinical phenotype, arylsulfatase B enzyme activity ®, clinical management was limited to supportive care and hematopoietic stem cell transplantation. Galsulfase is now widely available and is a specific therapy providing improved endurance with an acceptable safety profile. Prognosis is variable depending on the age of onset, rate of disease progression, age at initiation of ERT and on the quality of the medical care provided.

Integrated Cr(VI) removal using constructed wetlands and composting.

Science.gov (United States)

Sultana, Mar-Yam; Chowdhury, Abu Khayer Md Muktadirul Bari; Michailides, Michail K; Akratos, Christos S; Tekerlekopoulou, Athanasia G; Vayenas, Dimitrios V

2015-01-08

The present work was conducted to study integrated chromium removal from aqueous solutions in horizontal subsurface (HSF) constructed wetlands. Two pilot-scale HSF constructed wetlands (CWs) units were built and operated. One unit was planted with common reeds (Phragmites australis) and one was kept unplanted. Influent concentrations of Cr(VI) ranged from 0.5 to 10mg/L. The effect of temperature and hydraulic residence time (8-0.5 days) on Cr(VI) removal were studied. Temperature was proved to affect Cr(VI) removal in both units. In the planted unit maximum Cr(VI) removal efficiencies of 100% were recorded at HRT's of 1 day with Cr(VI) concentrations of 5, 2.5 and 1mg/L, while a significantly lower removal rate was recorded in the unplanted unit. Harvested reed biomass from the CWs was co-composted with olive mill wastes. The final product had excellent physicochemical characteristics (C/N: 14.1-14.7, germination index (GI): 145-157%, Cr: 8-10mg/kg dry mass), fulfills EU requirements and can be used as a fertilizer in organic farming. Copyright © 2014 Elsevier B.V. All rights reserved.

Retention of U(VI) onto silica in presence of model organic molecules

International Nuclear Information System (INIS)

Pham, T.T.H.; Mercier-Bion, F.; Drot, R.; Lagarde, G.; Simoni, E.; Lambert, J.

2008-01-01

It is well-known that the organic matter influences the retention of ions onto mineral surfaces. However, the major part of concerned studies implies humic substances and complex solids. Another approach for identifying the sorption mechanisms is possible by studying simpler solids than those present in natural medium. So, silica is chosen as mineral surface because of its abundance in soils and of the presence of Si-O groups in clayey minerals. Uranium (VI) is selected as cation. Simple organic molecules like acetic (one carboxylic group) and oxalic (two carboxylic functions) acids are considered as models of the natural organic matter for understanding their role in the retention of U(VI) onto powders and slides of silica. Binary (organics/silica, U(VI)/silica) and ternary systems (organics/silica/U(VI)) are studied by complementary approaches. Sorption edges as function of pH are obtained by liquid scintillation methods and capillary electrophoresis. Different spectroscopic techniques are used to deduce the interactions between the organic matter and U(VI) sorbed onto the silica whose: Time-Resolved Laser induced Fluorescence Spectroscopy (TRLFS), X-ray Photoelectron Spectroscopy (XPS), Nuclear Microprobe Analysis (NMA). The results of the effect of these model organic molecules onto the U(VI) retention showed a good agreement between the different techniques. Concerning the acetic acid, there are not differences in the sorption percentages of uranyl (see the figure). All these results indicate that the uranyl-acetate complexes stay in the aqueous solution rather than sorbing onto the silica. On the contrary, oxalic acid influences the sorption of U(VI) onto the silica surface. The sorption percentage of U(VI) in the ternary system (oxalic acid/silica/U(VI)) is lower than the binary system (U(VI)/silica) (see the figure). So, the presence of oxalic acid decreases the sorption of U(VI) onto the silica surface. (authors)

Experimental Monitoring of Cr(VI) Bio-reduction Using Electrochemical Geophysics

International Nuclear Information System (INIS)

Birsen Canan; Gary R. Olhoeft; William A. Smith

2007-01-01

Many Department of Energy (DOE) sites are contaminated with highly carcinogenic hexavalent chromium (Cr(VI)). In this research, we explore the feasibility of applying complex resistivity to the detection and monitoring of microbially-induced reduction of hexavalent chromium (Cr(VI)) to a less toxic form (Cr(III)). We hope to measure the change in ionic concentration that occurs during this reduction reaction. This form of reduction promises to be an attractive alternative to more expensive remedial treatment methods. The specific goal of this research is to define the minimum and maximum concentration of the chemical and biological compounds in contaminated samples for which the Cr(VI) - Cr(III) reduction processes could be detected via complex resistivity. There are three sets of experiments, each comprised of three sample columns. The first experiment compares three concentrations of Cr(VI) at the same bacterial cell concentration. The second experiment establishes background samples with, and without, Cr(VI) and bacterial cells. The third experiment examines the influence of three different bacterial cell counts on the same concentration of Cr(VI). A polarization relaxation mechanism was observed between 10 and 50 Hz. The polarization mechanism, unfortunately, was not unique to bio-chemically active samples. Spectral analysis of complex resistivity data, however, showed that the frequency where the phase minimum occurred was not constant for bio-chemically active samples throughout the experiment. A significant shifts in phase minima occurred between 10 to 20 Hz from the initiation to completion of Cr(VI) reduction. This phenomena was quantified using the Cole-Cole model and the Marquardt-Levenberg nonlinear least square minimization method. The data suggests that the relaxation time and the time constant of this relaxation are the Cole-Cole parameters most sensitive to changes in biologically-induced reduction of Cr(VI)

Paisaje del viñedo: patrimonio y recurso

Directory of Open Access Journals (Sweden)

Luis Vicente Elías

2008-01-01

Full Text Available La propuesta de que el paisaje del viñedo sea el complemento a la visita a la bodega, siendo esta el eje del turismo del vino, es el objetivo de este trabajo. Repasando los conceptos variables de patrimonio, llegamos al paisaje del viñedo como recurso, formando parte del patrimonio natural. Pero este no se puede desvincular de los otros aspectos patrimoniales, por lo que la cultura tradicional es el soporte de la tipología de paisaje que queremos proponer y que va contrastar con los nuevos paisajes del viñedo que surgen de las recientes técnicas en los cultivos y de la actual vitivicultura, emparejada con una moderna “cultura del vino”. El análisis de las diversas normativas, que salvaguardan el paisaje y la comprobación del escaso valor legal del paisaje del viñedo, es otro puntal de este trabajo que trata de unir paisaje con cultura tradicional como recursos del Turismo del Vino, integrados en las Rutas del Vino.

Recyclable magnetic photocatalysts of Fe2+/TiO2 hierarchical architecture with effective removal of Cr(VI) under UV light from water

International Nuclear Information System (INIS)

Xu, S.C.; Zhang, Y.X.; Pan, S.S.; Ding, H.L.; Li, G.H.

2011-01-01

Highlights: ► Fe 2+ /TiO 2 catalyst has a three-level hierarchical architecture. ► With a removal effectiveness of 99.3% at Cr(VI) concentration of 10 mg L −1 . ► Two-step reduction: TiO 2 photoreduces Fe 2+ to Fe and Fe reduces Cr(VI) to Cr(III). ► Hierarchical architecture serves as both photocatalytic reactor and absorbent. ► Fe 2+ /TiO 2 catalyst can be magnetically separated from wastewater and recycled. - Abstract: We report the synthesis and photocatalytic removal of Cr(VI) from water of hierarchical micro/nanostructured Fe 2+ /TiO 2 tubes. The TiO 2 tubes fabricated by a facile solvothermal approach show a three-level hierarchical architecture assembled from dense nanosheets nearly vertically standing on the surface of TiO 2 microtube. The nanosheets with a thickness of about 20 nm are composed of numerous TiO 2 nanocrystals with size in the range of 15–20 nm. Ferrous ions are doped into the hierarchical architecture by a reduction route. The Fe 2+ /TiO 2 catalyst demonstrates an effective removal of Cr(VI) from water under UV light and the removal effectiveness reaches 99.3% at the initial Cr(VI) concentration of 10 mg L −1 . The ferrous ion in the catalyst serves not as the photo-electron trap but as an intermedium of a two-step reduction. The TiO 2 photoreduces the Fe 2+ ions to Fe atoms firstly, then the Fe atoms reduce the Cr(VI) to Cr(III), and the later is removed by adsorption. The hierarchical architecture of the catalyst serves as a reactor for the photocatalytic reaction of Cr(VI) ions and an effective absorbent for the removal of Cr(III) ions. The catalyst can be easily magnetically separated from the wastewater after photocatalytic reaction and recycled after acid treatment.

Delineation and Diagnostic Criteria of Oral-Facial-Digital Syndrome Type VI

Directory of Open Access Journals (Sweden)

Poretti Andrea

2012-01-01

Full Text Available Abstract Oral-Facial-Digital Syndrome type VI (OFD VI represents a rare phenotypic subtype of Joubert syndrome and related disorders (JSRD. In the original report polydactyly, oral findings, intellectual disability, and absence of the cerebellar vermis at post-mortem characterized the syndrome. Subsequently, the molar tooth sign (MTS has been found in patients with OFD VI, prompting the inclusion of OFD VI in JSRD. We studied the clinical, neurodevelopmental, neuroimaging, and genetic findings in a cohort of 16 patients with OFD VI. We derived the following inclusion criteria from the literature: 1 MTS and one oral finding and polydactyly, or 2 MTS and more than one typical oral finding. The OFD VI neuroimaging pattern was found to be more severe than in other JSRD subgroups and includes severe hypoplasia of the cerebellar vermis, hypoplastic and dysplastic cerebellar hemispheres, marked enlargement of the posterior fossa, increased retrocerebellar collection of cerebrospinal fluid, abnormal brainstem, and frequently supratentorial abnormalities that occasionally include characteristic hypothalamic hamartomas. Additionally, two new JSRD neuroimaging findings (ascending superior cerebellar peduncles and fused thalami have been identified. Tongue hamartomas, additional frenula, upper lip notch, and mesoaxial polydactyly are specific findings in OFD VI, while cleft lip/palate and other types of polydactyly of hands and feet are not specific. Involvement of other organs may include ocular findings, particularly colobomas. The majority of the patients have absent motor development and profound cognitive impairment. In OFD VI, normal cognitive functions are possible, but exceptional. Sequencing of known JSRD genes in most patients failed to detect pathogenetic mutations, therefore the genetic basis of OFD VI remains unknown. Compared with other JSRD subgroups, the neurological findings and impairment of motor development and cognitive functions in OFD

New approach in modeling Cr(VI) sorption onto biomass from metal binary mixtures solutions

Energy Technology Data Exchange (ETDEWEB)

Liu, Chang [College of Environmental Science and Engineering, Anhui Normal University, South Jiuhua Road, 189, 241002 Wuhu (China); Chemical Engineering Department, Escola Politècnica Superior, Universitat de Girona, Ma Aurèlia Capmany, 61, 17071 Girona (Spain); Fiol, Núria [Chemical Engineering Department, Escola Politècnica Superior, Universitat de Girona, Ma Aurèlia Capmany, 61, 17071 Girona (Spain); Villaescusa, Isabel, E-mail: Isabel.Villaescusa@udg.edu [Chemical Engineering Department, Escola Politècnica Superior, Universitat de Girona, Ma Aurèlia Capmany, 61, 17071 Girona (Spain); Poch, Jordi [Applied Mathematics Department, Escola Politècnica Superior, Universitat de Girona, Ma Aurèlia Capmany, 61, 17071 Girona (Spain)

2016-01-15

In the last decades Cr(VI) sorption equilibrium and kinetic studies have been carried out using several types of biomasses. However there are few researchers that consider all the simultaneous processes that take place during Cr(VI) sorption (i.e., sorption/reduction of Cr(VI) and simultaneous formation and binding of reduced Cr(III)) when formulating a model that describes the overall sorption process. On the other hand Cr(VI) scarcely exists alone in wastewaters, it is usually found in mixtures with divalent metals. Therefore, the simultaneous removal of Cr(VI) and divalent metals in binary mixtures and the interactive mechanism governing Cr(VI) elimination have gained more and more attention. In the present work, kinetics of Cr(VI) sorption onto exhausted coffee from Cr(VI)–Cu(II) binary mixtures has been studied in a stirred batch reactor. A model including Cr(VI) sorption and reduction, Cr(III) sorption and the effect of the presence of Cu(II) in these processes has been developed and validated. This study constitutes an important advance in modeling Cr(VI) sorption kinetics especially when chromium sorption is in part based on the sorbent capacity of reducing hexavalent chromium and a metal cation is present in the binary mixture. - Highlights: • A kinetic model including Cr(VI) reduction, Cr(VI) and Cr(III) sorption/desorption • Synergistic effect of Cu(II) on Cr(VI) elimination included in the model • Model validation by checking it against independent sets of data.

New approach in modeling Cr(VI) sorption onto biomass from metal binary mixtures solutions

International Nuclear Information System (INIS)

Liu, Chang; Fiol, Núria; Villaescusa, Isabel; Poch, Jordi

2016-01-01

In the last decades Cr(VI) sorption equilibrium and kinetic studies have been carried out using several types of biomasses. However there are few researchers that consider all the simultaneous processes that take place during Cr(VI) sorption (i.e., sorption/reduction of Cr(VI) and simultaneous formation and binding of reduced Cr(III)) when formulating a model that describes the overall sorption process. On the other hand Cr(VI) scarcely exists alone in wastewaters, it is usually found in mixtures with divalent metals. Therefore, the simultaneous removal of Cr(VI) and divalent metals in binary mixtures and the interactive mechanism governing Cr(VI) elimination have gained more and more attention. In the present work, kinetics of Cr(VI) sorption onto exhausted coffee from Cr(VI)–Cu(II) binary mixtures has been studied in a stirred batch reactor. A model including Cr(VI) sorption and reduction, Cr(III) sorption and the effect of the presence of Cu(II) in these processes has been developed and validated. This study constitutes an important advance in modeling Cr(VI) sorption kinetics especially when chromium sorption is in part based on the sorbent capacity of reducing hexavalent chromium and a metal cation is present in the binary mixture. - Highlights: • A kinetic model including Cr(VI) reduction, Cr(VI) and Cr(III) sorption/desorption • Synergistic effect of Cu(II) on Cr(VI) elimination included in the model • Model validation by checking it against independent sets of data

Cr(VI) retention and transport through Fe(III)-coated natural zeolite

Energy Technology Data Exchange (ETDEWEB)

Du, Gaoxiang [School of Materials Science and Technology, China University of Geosciences, Beijing 100083 (China); Li, Zhaohui, E-mail: li@uwp.edu [School of Materials Science and Technology, China University of Geosciences, Beijing 100083 (China); Geosciences Department, University of Wisconsin-Parkside, Kenosha, WI 53144 (United States); Department of Earth Sciences, National Cheng Kung University, 1 University Road, Tainan 70101, Taiwan (China); Liao, Libing [School of Materials Science and Technology, China University of Geosciences, Beijing 100083 (China); Hanson, Renee; Leick, Samantha; Hoeppner, Nicole [Geosciences Department, University of Wisconsin-Parkside, Kenosha, WI 53144 (United States); Jiang, Wei-Teh [Department of Earth Sciences, National Cheng Kung University, 1 University Road, Tainan 70101, Taiwan (China)

2012-06-30

Graphical abstract: Breakthrough curves of Cr(VI) from columns packed with raw zeolite (a) and Fe(III)-zeolite (b). The solid line in (b) is the HYDRUS-1D fit to the observed data with adsorption term only, while the dashed line in (b) includes a reduction term in the HYDRUS-1D fit. Highlights: Black-Right-Pointing-Pointer Zeolite modified with Fe(III) could be used for adsorption and retention of Cr(VI). Black-Right-Pointing-Pointer The Fe present on zeolite was in an amorphous Fe(OH){sub 3} form. Black-Right-Pointing-Pointer A Cr(VI) adsorption capacity of 82 mg/kg was found on Fe(III)-zeolite. Black-Right-Pointing-Pointer A Cr(VI) retardation factor of 3 or 5 was determined from column and batch studies. - Abstract: Cr(VI) is a group A chemical based on the weight of evidence of carcinogenicity. Its transport and retention in soils and groundwater have been studied extensively. Zeolite is a major component in deposits originated from volcanic ash and tuff after alteration. In this study, zeolite aggregates with the particle size of 1.4-2.4 mm were preloaded with Fe(III). The influence of present Fe(III) on Cr(VI) retention by and transport through zeolite was studied under batch and column experiments. The added Fe(III) resulted in an enhanced Cr(VI) retention by the zeolite with a capacity of 82 mg/kg. The Cr(VI) adsorption on Fe(III)-zeolite followed a pseudo-second order kinetically and the Freundlich adsorption isotherm thermodynamically. Fitting the column experimental data to HYDRUS-1D resulted in a retardation factor of 3 in comparison to 5 calculated from batch tests at an initial Cr(VI) concentration of 3 mg/L. The results from this study showed that enhanced adsorption and retention of Cr(VI) may happen in soils derived from volcanic ash and tuff that contains significant amounts of zeolite with extensive Fe(III) coating.

Simultaneous Treatment of Agro-Industrial and Industrial Wastewaters: Case Studies of Cr(VI/Second Cheese Whey and Cr(VI/Winery Effluents

Directory of Open Access Journals (Sweden)

Triantafyllos I. Tatoulis

2018-03-01

Full Text Available Hexavalent chromium (Cr(VI was co-treated either with second cheese whey (SCW or winery effluents (WE using pilot-scale biological trickling filters in series under different operating conditions. Two pilot-scale filters in series using plastic support media were used in each case. The first filter (i.e., Cr-SCW-filter or Cr-WE-filter aimed at Cr(VI reduction and the partial removal of dissolved chemical oxygen demand (d-COD from SCW or WE and was inoculated with indigenous microorganisms originating from industrial sludge. The second filter in series (i.e., SCW-filter or WE-filter aimed at further d-COD removal and was inoculated with indigenous microorganisms that were isolated from SCW or WE. Various Cr(VI (5–100 mg L−1 and SCW or WE (d-COD, 1000–25,000 mg L−1 feed concentrations were tested. Based on the experimental results, the sequencing batch reactor operating mode with recirculation of 0.5 L min−1 proved very efficient since it led to complete Cr(VI reduction in the first filter in series and achieved high Cr(VI reduction rates (up to 36 and 43 mg L−1 d−1, for SCW and WW, respectively. Percentage d-COD removal for SCW and WE in the first filter was rather low, ranging from 14 to 42.5% and from 4 to 29% in the Cr-SCW-filter and Cr-WE-filter, respectively. However, the addition of the second filter in series enhanced total d-COD removal to above 97% and 90.5% for SCW and WE, respectively. The above results indicate that agro-industrial wastewater could be used as a carbon source for Cr(VI reduction, while the use of two trickling filters in series could effectively treat both industrial and agro-industrial wastewaters with very low installation and operational costs.

Ternary uranium(VI) carbonato humate complex studied by cryo-TRLFS

Energy Technology Data Exchange (ETDEWEB)

Steudtner, R.; Sachs, S.; Schmeide, K.; Brendler, V.; Bernhard, G. [Helmholtz-Zentrum Dresden-Rossendorf, Dresden (Germany). Inst. of Radiochemistry

2011-07-01

The complex formation of U(VI) with humic acid (HA) in the presence of carbonate was studied by time-resolved laser-induced fluorescence spectroscopy at low temperature (cryo-TRLFS) at pH 8.5. In the presence of HA, a decrease of the luminescence intensity of U(VI) and no shift of the emission band maxima in comparison to the luminescence spectrum of the UO{sub 2}(CO{sub 3}){sub 3}{sup 4-} complex, the dominating U(VI) species under the applied experimental conditions in the absence of HA, was observed. The formation of a ternary U(VI) carbonato humate complex of the type UO{sub 2}(CO{sub 3}){sub 2}HA(II){sup 4-} starting from UO{sub 2}(CO{sub 3}){sub 3}{sup 4-} was concluded from the luminescence data. For this complex a complex stability constant of log K=2.83 {+-} 0.17 was determined. Slope analysis resulted in a slope of 1.12 {+-} 0.11, which verifies the postulated complexation reaction. The results agree very well with literature data. Speciation calculations show that the formation of the ternary U(VI) carbonato humate complex can significantly influence the U(VI) speciation under environmental conditions. (orig.)

Recovery of uranium (VI) from low level aqueous radioactive waste

International Nuclear Information System (INIS)

Kulshrestha, Mukul

1996-01-01

Investigation was undertaken to evaluate the uranium (VI) removal and recovery potential of a naturally occurring, nonviable macrofungus, Ganoderma Lucidum from the simulated low level aqueous nuclear waste. These low level waste waters discharged from nuclear mine tailings and nuclear power reactors have a typical U(VI) concentration of 10-100 mg/L. It is possible to recover this uranium economically with the advent of biosorption as a viable technology. Extensive laboratory studies have revealed Ganoderma Lucidum to be a potential biosorbent with a specific uptake of 2.75 mg/g at an equilibrium U(VI) concentration of 10 mg/L at pH 4.5. To recover the sorbed U(VI), the studies indicated 0.2N Na 2 CO 3 to be an effective elutant. The kinetics of U(VI) desorption from loaded Ganoderma Lucidum with 0.2N Na 2 CO 3 as elutant, was found to be rapid with more than 75% recovery occurring in the first five minutes, the specific metal release rate being 0.102 mg/g/min. The equilibrium data fitted to a linearised Freundlich plot and exhibited a near 100% recovery of sorbed U(VI), clearly revealing a cost-effective method of recovery of precious uranium from low level wastewater. (author). 7 refs., 3 figs., 1 tab

A numerical investigation into the influence of the properties of cobalt chrome cellular structures on the load transfer to the periprosthetic femur following total hip arthroplasty.

Science.gov (United States)

Hazlehurst, Kevin Brian; Wang, Chang Jiang; Stanford, Mark

2014-04-01

Stress shielding of the periprosthetic femur following total hip arthroplasty is a problem that can promote the premature loosening of femoral stems. In order to reduce the need for revision surgery it is thought that more flexible implant designs need to be considered. In this work, the mechanical properties of laser melted square pore cobalt chrome molybdenum cellular structures have been incorporated into the design of a traditional monoblock femoral stem. The influence of incorporating the properties of cellular structures on the load transfer to the periprosthetic femur was investigated using a three dimensional finite element model. Eleven different stiffness configurations were investigated by using fully porous and functionally graded approaches. This investigation confirms that the periprosthetic stress values depend on the stiffness configuration of the stem. The numerical results showed that stress shielding is reduced in the periprosthetic Gruen zones when the mechanical properties of cobalt chrome molybdenum cellular structures are used. This work identifies that monoblock femoral stems manufactured using a laser melting process, which are designed for reduced stiffness, have the potential to contribute towards reducing stress shielding. Copyright © 2014 IPEM. Published by Elsevier Ltd. All rights reserved.

Solvent impregnated resin for isolation of U(VI) from industrial wastes

International Nuclear Information System (INIS)

Karve, M.; Rajgor, R.V.

2008-01-01

A solid-phase extraction method based upon impregnation of Cyanex 302 (bis(2,4,4- trimethylpentyl)mono-thio-phosphinic acid) on Amberlite XAD-2 resin is proposed for isolation of U(VI) from uranmicrolite ore tailing samples and industrial effluent samples. U(VI) was sorbed from nitric acid media on the solvent-impregnated resin (SIR) and was recovered completely with 1.0 M HCl. Based upon sorption behavior of U(VI) with Cyanex 302, it was quantitatively sorbed on the SIR in a dynamic method, while the other metal ions were not sorbed by the modified resin. The preparation of impregnated resin is simple, based upon physical interaction of the extractant and solid support, has good sorption capacity for U(VI), and is also reliable for detection of traces of U(VI). (authors)

190-C Facility <90 Day Storage Pad training plan

International Nuclear Information System (INIS)

Little, N.C.

1996-12-01

This is the Environmental Restoration Contractor (ERC) team training plan for the 190-C Facility <90 Day Storage Pad of Hazardous Waste. It is intended to meet the requirements of Washington Administrative Code (WAC) 173-303-330 and the Hanford Dangerous Waste Permit. Training unrelated to compliance with WAC 173-303-330 is not addressed in this training plan. WAC 173-303-330(1)(d)(ii, v, vi) requires that personnel be familiarized, where applicable, with waste feed cut-off systems, response to ground-water contamination incidents, and shutdown of operations. These are not applicable to 190-C Facility <90 Day Storage Pad, and are therefore not covered in this training plan

Cr (VI) remediation by indigenous bacteria in soils contaminated by chromium-containing slag

International Nuclear Information System (INIS)

Chai Liyuan; Huang Shunhong; Yang Zhihui; Peng Bing; Huang Yan; Chen Yuehui

2009-01-01

Hexavalent chromium (Cr) is a toxic element causing serious environmental threat. Recently, more and more attention is paid to the bio-remediation of Cr (VI) in the contaminated soils. Cr (VI) remediation by indigenous bacteria in soils contaminated by chromium-containing slag at a steel-alloy factory in Hunan Province, China, was investigated in the present study. The results showed that when sufficient nutrients were amended into the contaminated soils, total Cr (VI) concentration declined from the initial value of 462.8 to 10 mg kg -1 at 10 days and the removal rate was 97.8%. Water soluble Cr (VI) decreased from the initial concentration of 383.8 to 1.7 mg kg -1 . Exchangeable Cr (VI) and carbonates-bound Cr (VI) were removed by 92.6% and 82.4%, respectively. Meanwhile, four Cr (VI) resistant bacterial strains were isolated from the soil under the chromium-containing slag. Only one strain showed a high ability for Cr (VI) reduction in liquid culture. This strain was identified as Pannonibacter phragmitetus sp. by gene sequencing of 16S rRNA. X-ray photoelectron spectroscope (XPS) analysis indicated that Cr (VI) was reduced into trivalent chromium. The results suggest that indigenous bacterial strains have potential application for Cr (VI) remediation in the soils contaminated by chromium-containing slag.

Impact of water quality parameters on the sorption of U(VI) onto hematite

International Nuclear Information System (INIS)

Zhao Donglin; Wang Xianbiao; Yang Shitong; Guo Zhiqiang; Sheng Guodong

2012-01-01

In this study, the sorption of U(VI) from aqueous solution on hematite was studied as a function of various water quality parameters such as contact time, pH, ionic strength, soil humic acid (HA) or fulvic acid (FA), solid content and temperature by using a batch technique. The results demonstrated that the sorption of U(VI) was strongly dependent on ionic strength at pH 6.0 and the sorption was mainly dominated by inner-sphere surface complexation. The presence of HA/FA increases U(VI) sorption at low pH, whereas decreases U(VI) sorption at high pH. The thermodynamic parameters (ΔH 0 , ΔS 0 , and ΔG 0 ) were calculated from the temperature dependent sorption isotherms, and the results suggested that U(VI) sorption was a spontaneous and endothermic process. The results might be important for the application of hematite in U(VI) pollution management. Highlights: ► The sorption of U(VI) was strongly dependent on ionic strength at pH 6.0. ► A positive effect of HA/FA on U(VI) sorption was found at low pH, whereas a negative effect was observed at high pH. ► U(VI) sorption was a spontaneous and endothermic process. ► The results are quite important for the application of hematite in U(VI) pollution management.

Electrochemical processes for the environmental remediation of toxic Cr(VI): A review

International Nuclear Information System (INIS)

Jin, Wei; Du, Hao; Zheng, Shili; Zhang, Yi

2016-01-01

Highlights: • Recent advances in electrochemical technologies for practical Cr(VI) treatment applications was reviewed. • The mechanism and performance of electrocoagulation, electrochemical reduction, electrodialysis, electro-electrodialysis and electrodeionization were discussed and compared. • The remained challenges and future perspectives were commented. - Abstract: Hexavalent chromium Cr(VI) is extremely toxic and classified as one of the 17 chemicals posing the greatest threat to humans. Large amounts of Cr(VI) compounds are directly or indirectly discharged into the environment, therefore considerable efforts have been made to control the Cr(VI) concentration below the recommended level. It has been demonstrated that electrochemical technique is one of the most efficient and environmental benign approach for the Cr(VI) removal. This review aims at recent advances in electrochemical technology for practical Cr(VI) treatment applications. By using the “clean reagent” of electron, Cr(VI) can be completely eliminated or separated via different electrochemical techniques such as electrocoagulation, electrochemical reduction, electrodialysis, electro-electrodialysis and electrodeionization. Besides, the mechanism and performance of different strategies are commented and compared. The treatment process is largely dependent on variables such as pH, electrode materials, cell configuration and techniques integration. Furthermore, the remained limitation and challenges for the electrochemical Cr(VI) remediation are also discussed.

Bulk solubility and speciation of plutonium(VI) in phosphate-containing solutions

International Nuclear Information System (INIS)

Weger, H.T.; Okajima, S.; Cunnane, J.C.; Reed, D.T.

1992-01-01

The solubility and speciation of Pu(VI) with phosphate as a function of pH was investigated to determine the ability of phosphate to act as an actinide getter. The general properties were first investigated and are reported here with the goal of performing more quantitative experiments in the future. Solubility was approached from oversaturation at initial pH = 4, 10 and 13.4. Absorption spectra were recorded, the solution filtered and the filtrate counted. Absorption spectra were obtained at varying phosphate concentrations and at pH of 2.7 to 11.9. The effect of complexation on the 833 mn Pu(VI) band was characterized. Evidence for three phosphate complexes was obtained for pH -5 to 10 -6 M Pu(VI) was measured in the filtrate at pH ≤ 10 that were passed through a 50 mn filter. Pu(VI) complexes with phosphate over hydroxide at pH ≤ 11.6, but at pH ≥ 11.9, only hydrolyzed Pu(VI) was detected. At pH = 12, the concentration of Pu(VI) was as high as 10 -4 M

Bacillus lichenformis γ-glutamyl exopolymer: Physicochemical characterization and U(VI) interaction

International Nuclear Information System (INIS)

He, L.M.; Neu, M.P.; Vanderberg, L.A.

2000-01-01

Complexation by microbially produced exopolymers may significantly impact the environmental mobility and toxicity of metals. This study focused on the conformational structure of the bacterial exopolymer, γ-D-poly(glutamic acid) and its interactions with U(VI) examined using ATR-FTIR spectroscopy. Solution pH, polymer concentration, and ionic strength affected the conformation of the exopolymer, and U(VI) binding was monitored. At low pH, low concentration, or low ionic strength, this exopolymer exists in an α-helical conformation, while at high pH, concentration, or ionic strength the exopolymer exhibits a β-sheet structure. The change in exopolymer conformation is likely to influence the number and nature of exposed surface functional groups, sites most responsible for metal complexation. The authors found the polyglutamate capsule binds U(VI) in a binuclear, bidentate fashion; in contrast the glutamate monomer forms a mononuclear, bidentate complex with U(VI). The apparent polynuclear binding of U(VI) may induce β-sheet structure formation provided the U(VI) Concentration is sufficiently high

Selectivity enhancement of phosphate based functional polymeric gels towards Uranium(VI) using ion imprinting

International Nuclear Information System (INIS)

Chappa, Sankararao; Agarwal, Chhavi; Pandey, A.K.

2015-01-01

The imprinting of gel containing polymer chains of ethylene glycol methacrylate phosphate (EGMP) for U(VI) ions were carried out. The U(VI) imprinting has been carried out in pure EGMP and in EGMP: poly(ethylene glycol) methacrylate (PEGMA) = 1:9 composition. Complexation of the monomer with template (U(VI)) followed by polymerization have been used to imprint the U(VI) onto the polymer chains. The comparison of uptake studies of U(VI) and Pu(IV) at 3 M HNO 3 shows increased selectivity of U(VI) relative to Pu(IV) for both the gel compositions. The less uptake of U(VI) for imprinted EGMP:PEGMA gel relative to pure imprinted EGMP gel at tracer level can be possibly due to the requirement of two EGMP units in the vicinity for U(VI) complexation. (author)

Enhancing Surface Finish of Additively Manufactured Titanium and Cobalt Chrome Elements Using Laser Based Finishing

Science.gov (United States)

Gora, Wojciech S.; Tian, Yingtao; Cabo, Aldara Pan; Ardron, Marcus; Maier, Robert R. J.; Prangnell, Philip; Weston, Nicholas J.; Hand, Duncan P.

Additive manufacturing (AM) offers the possibility of creating a complex free form object as a single element, which is not possible using traditional mechanical machining. Unfortunately the typically rough surface finish of additively manufactured parts is unsuitable for many applications. As a result AM parts must be post-processed; typically mechanically machined and/or and polished using either chemical or mechanical techniques (both of which have their limitations). Laser based polishing is based on remelting of a very thin surface layer and it offers potential as a highly repeatable, higher speed process capable of selective area polishing, and without any waste problems (no abrasives or liquids). In this paper an in-depth investigation of CW laser polishing of titanium and cobalt chrome AM elements is presented. The impact of different scanning strategies, laser parameters and initial surface condition on the achieved surface finish is evaluated.

Clinical evaluation of complete solo surgery with the "ViKY®" robotic laparoscope manipulator.

Science.gov (United States)

Takahashi, Masahiro; Takahashi, Masanori; Nishinari, Naoto; Matsuya, Hideki; Tosha, Tsutomu; Minagawa, Yukihiro; Shimooki, Osamu; Abe, Tadashi

2017-02-01

Advancement in both surgical technique and medical equipment has enabled solo surgery. ViKY ® Endoscope Positioning System (ViKY ® ) is a robotic system that remotely controls an endoscope and provides direct vision control to the surgeon. Here, we report our experience with ViKY ® -assisted solo surgery. We retrospectively examined 25 cases of solo surgery TAPP with ViKY ® . ViKY ® was setup by the surgeon alone, and the setup duration was determined as the time at which the side rail was positioned and that when the endoscope was installed. For assessing the control unit, the number of false movements was counted. We compared the operative results between ViKY ® -assisted solo surgery TAPP and the conventional method with an assistant. The average time to set up ViKY ® was 7.9 min. The average number of commands for ViKY ® during surgery was 98.3, and the average number of errors and no response of control unit was 7.9. The mean duration of surgery was 136 min for the ViKY ® group, including the setup time, and 117 min for the conventional method. No case required an assistant during the operation. There was also no difference between the two groups with regard to postoperative complications and the rate of recurrence. ViKY ® proved reliable in recognizing orders with very few failures, and the operations were performed safely and were comparable to the conventional operations with assistants. Solo surgery with ViKY ® was beneficial in this clinical evaluation.

cis-dioxomolybdenum(VI)-(ONO)

Indian Academy of Sciences (India)

Various ONO type Schiff base ligands L(H)2 used for the preparation of ... and derivatives.6–33 Depending on the method of prepa- ration .... HCl. Scheme 6. Synthesis of a Mo(VI) Schiff base complexe by selective inversion at C–1 carbon of a ...

Multi-crystalline II-VI based multijunction solar cells and modules

Science.gov (United States)

Hardin, Brian E.; Connor, Stephen T.; Groves, James R.; Peters, Craig H.

2015-06-30

Multi-crystalline group II-VI solar cells and methods for fabrication of same are disclosed herein. A multi-crystalline group II-VI solar cell includes a first photovoltaic sub-cell comprising silicon, a tunnel junction, and a multi-crystalline second photovoltaic sub-cell. A plurality of the multi-crystalline group II-VI solar cells can be interconnected to form low cost, high throughput flat panel, low light concentration, and/or medium light concentration photovoltaic modules or devices.

24 CFR 972.115 - Relationship between required conversions and HOPE VI developments.

Science.gov (United States)

2010-04-01

... conversions and HOPE VI developments. 972.115 Section 972.115 Housing and Urban Development Regulations... Relationship between required conversions and HOPE VI developments. HUD actions to approve or deny proposed HOPE VI revitalization plans must be consistent with the requirements of this subpart. Developments...

A combined wet chemistry and EXAFS study of U(VI) uptake by cementitious materials

International Nuclear Information System (INIS)

Wieland, E.; Harfouche, M.; Tits, J.; Kunz, D.; Daehn, R.; Fujita, T.; Tsukamoto, M.

2006-01-01

The sorption behaviour and speciation of U(VI) in cementitious systems was investigated by a combination of wet chemistry experiments and synchrotron-based X-ray absorption spectroscopy (XAS) measurements. Radiotracer studies using 233 U were carried out on hardened cement paste (HCP) and calcium silicate hydrates (C-S-H), which are the major constituents of HCP, to determine the uptake kinetics and sorption isotherms. C-S-H phases were synthesized using different methods for solid phase preparation, which enabled us to study the U(VI) uptake by different types of C-S-H phases and a wide range of Ca/Si compositions, and to distinguish U(VI) sorption on the surface of C-S-H from U(VI) incorporation into the structure. XAS measurements were performed using U(VI) loaded HCP and C-S-H materials (sorption and co-precipitation samples) to gain structural information on the U(VI) speciation in these systems, i.e., the type and number of neighbouring atoms, and bond distances. Examples of studies that have utilized XAS to characterize U(VI) speciation in cementitious systems are still rare, and to the best of our knowledge, detailed XAS investigations of the U(VI)/C-S-H system are lacking. The results obtained from the combined use of wet chemical and spectroscopic techniques allow mechanistic models of the immobilization process to be proposed for cementitious waste forms containing low and high U(VI) inventories. In the latter case U(VI) immobilization is controlled by a solubility-limiting process with the U(VI) mineral predominantly formed under the conditions prevailing in cementitious systems. At low U(VI) concentrations, however, U(VI) appears to be predominantly bound onto C-S-H phases. The coordination environment of U(VI) taken up by C-S-H was found to resemble that of U(VI) in uranophane. A mechanistic understanding of the U(VI) binding by cementitious materials will allow more detailed and scientifically well founded predictions of the retention of

Contribution of extracellular polymeric substances from Shewanella sp. HRCR-1 biofilms to U(VI) immobilization.

Science.gov (United States)

Cao, Bin; Ahmed, Bulbul; Kennedy, David W; Wang, Zheming; Shi, Liang; Marshall, Matthew J; Fredrickson, Jim K; Isern, Nancy G; Majors, Paul D; Beyenal, Haluk

2011-07-01

The goal of this study was to quantify the contribution of extracellular polymeric substances (EPS) to U(VI) immobilization by Shewanella sp. HRCR-1. Through comparison of U(VI) immobilization using cells with bound EPS (bEPS) and cells with minimal EPS, we show that (i) bEPS from Shewanella sp. HRCR-1 biofilms contribute significantly to U(VI) immobilization, especially at low initial U(VI) concentrations, through both sorption and reduction; (ii) bEPS can be considered a functional extension of the cells for U(VI) immobilization and they likely play more important roles at lower initial U(VI) concentrations; and (iii) the U(VI) reduction efficiency is dependent upon the initial U(VI) concentration and decreases at lower concentrations. To quantify the relative contributions of sorption and reduction to U(VI) immobilization by EPS fractions, we isolated loosely associated EPS (laEPS) and bEPS from Shewanella sp. HRCR-1 biofilms grown in a hollow fiber membrane biofilm reactor and tested their reactivity with U(VI). We found that, when reduced, the isolated cell-free EPS fractions could reduce U(VI). Polysaccharides in the EPS likely contributed to U(VI) sorption and dominated the reactivity of laEPS, while redox active components (e.g., outer membrane c-type cytochromes), especially in bEPS, possibly facilitated U(VI) reduction.

Sorption of chromium (VI) by Mg/Fe hydrotalcite type compunds

Energy Technology Data Exchange (ETDEWEB)

García-Sosa, I., E-mail: irma.garcia@inin.gob.mx; Cabral-Prieto, A., E-mail: agustin.cabral@inin.gob.mx [Instituto Nacional de Investigaciones Nucleares, Departamento de Química (Mexico); Nava, N., E-mail: tnava@imp.mx; Navarrete, J. [Instituto Mexicano del Petróleo (Mexico); Olguín, M. T., E-mail: teresa.olguin@inin.gob.mx [Instituto Nacional de Investigaciones Nucleares, Departamento de Química (Mexico); Escobar, Luis, E-mail: luis.escobar@inin.gob.mx [Instituto Nacional de Investigaciones Nucleares, Departamento de Física (Mexico); López-Castañares, R., E-mail: rlc@anuies.mx; Olea-Cardoso, O., E-mail: olc@anuies.mx [Universidad Autónoma del Edo. de México, Facultad de Química (Mexico)

2015-06-15

The synthesis by co-precipitation and characterization by X-ray diffraction, Raman and Mössbauer spectroscopies of Mg-Fe-hydrotalcite compounds, and their sorption capacities for Cr(VI) in aqueous media were carried out. The average sorption capacity of Cr(VI) for the non-thermal treated samples was of 6.2 mg/g. The ferrihydrite was omnipresent in all prepared hydrotalcite samples. A brief discussion is made on the role of both the hydrotalcite and ferrihydrite for removing such amount of Cr(VI)

Uranium(VI) retention on quartz and kaolinite. Experiments and modelling

International Nuclear Information System (INIS)

Mignot, G.

2001-01-01

The behaviour of uranium in the geosphere is an important issue for safety performance assessment of nuclear waste repositories, or in the context of contaminated sites due to mining activity related to nuclear field. Under aerobic conditions, the fate of uranium is mainly governed by the ability of minerals to sorb U(VI) aqueous species. Hence, a thorough understanding of U(VI) sorption processes on minerals is required to provide a valuable prediction of U(VI) migration in the environment. In this study, we performed sorption/desorption experiments of U(VI) on quartz and kaolinite, for systems favouring the formation in solution (i) of UO 2 2+ and monomeric hydrolysis products or (ii) of di-/tri-meric uranyl aqueous species, and / or U(VI)-colloids or UO 2 (OH) 2 precipitates, or (iii) of uranyl-carbonate complexes. Particular attention was paid to determine the surface characteristics of the solids and their modification due to dissolution/precipitation processes during experiments. A double layer surface complexation model was applied to our experimental data in order to derive surface complexation equilibria and intrinsic constants which allow a valuable description of U(VI) retention over a wide range of pH, ionic strength, initial concentration of uranium [0.1-10μM] and solid - solution equilibration time. U(VI) sorption on quartz was successfully modeled by using two sets of adsorption equilibria, assuming (i) the formation of the surface complexes SiOUO 2 + , SiOUO 2 OH and SiO(UO 2 ) 3 (OH) 5 , or (ii) the formation of the mono-dentate complex SiO(UO 2 ) 3 (OH) 5 and of the bidentate complex (SiO) 2 UO 2 . Assumptions on the density of each type of surface sites of kaolinite and on their acid-base properties were made from potentiometric titrations of kaolinite suspensions. We proposed on such a basis a set of surface complexation equilibria which accounts for U(VI) uptake on kaolinite over a wide range of chemical conditions, with aluminol edge sites as

Effet des polyamines sur la réduction du chrome hexavalent par des souches bactériennes et leur résistance

Directory of Open Access Journals (Sweden)

Tahri Joutey, N.

2014-01-01

Full Text Available Effect of polyamines on the reduction of hexavalent chromium by bacterial strains and their resistance. Polyamines are involved in several functions in bacteria. In this study, we examined the role of polyamines in hexavalent chromium (Cr[VI] reduction by three bacterial strains isolated from sites contaminated by tannery effluents. The strains were identified as Serratia proteamaculans, Leucobacter chromiireducens and Brevibacterium frigoritolerans. The inhibition of polyamine synthesis by α-difluoromethylornithine (DFMO caused a decrease in Cr(VI tolerance in the bacterial isolates, indicating the role of endogenous polyamines in resistance to Cr(VI. The exogenous application of polyamines (putrescine, spermidine, cadaverine was found to stimulate growth and Cr(VI reduction by the bacterial strains in Luria-Bertani medium. The results show the importance of polyamines in response to heavy metal stresses, especially Cr(VI toxicity.

strong>Hvad skal vi med en hjerne?strong>

DEFF Research Database (Denmark)

Hermansen, Judy

2009-01-01

neurologen Antonio Damasio, at sikre vores overlevelse og velbefindende (i nævnte rækkefølge). Vi ved, at der findes såkaldte belønningsstrukturer i hjernen på både dyr og mennesker, som aktiverer følelser af velbehag, når vi gør "det rigtige", dvs. noget der er godt for os. Men hvordan de mere konkret...

Syntheses and catalytic oxotransfer activities of oxo molybdenum(vi) complexes of a new aminoalcohol phenolate ligand.

Science.gov (United States)

Hossain, M K; Haukka, M; Sillanpää, R; Hrovat, D A; Richmond, M G; Nordlander, E; Lehtonen, A

2017-05-30

The new aminoalcohol phenol 2,4-di-tert-butyl-6-(((2-hydroxy-2-phenylethyl)amino)methyl)phenol (H2L) was prepared by a facile solvent-free synthesis and used as a tridentate ligand for new cis-dioxomolybdenum(vi)(L) complexes. In the presence of a coordinating solvent (DMSO, MeOH, pyridine), the complexes crystallise as monomeric solvent adducts while in the absence of such molecules, a trimer with asymmetric Mo[double bond, length as m-dash]O→Mo bridges crystallises. The complexes can catalyse epoxidation of cis-cyclooctene and sulfoxidation of methyl-p-tolylsulfide, using tert-butyl hydroperoxide as oxidant.

Reduction of Cr(VI) in aqueous solution with DC diaphragm glow discharge

International Nuclear Information System (INIS)

Wang, Xiaoyan; Jin, Xinglong; Zhou, Minghua; Chen, Zhenhai; Deng, Kai

2013-01-01

This paper investigated the reduction of Cr(VI) in aqueous solution with direct current diaphragm glow discharge (DGD). The glow discharge sustained around the hole on a quartz tube which divided the electrolyte cell into two parts. The reduction efficiencies of Cr(VI) under different applied voltages, initial conductivities, hole diameters, hole numbers, initial pH values and initial concentrations were systematically studied. The results showed that the reduction efficiency of Cr(VI) increased with the increase of applied voltage, initial conductivity, hole diameter and hole number. The different initial pH values showed less effects on the reduction of Cr(VI). The reduction efficiency decreased with the increasing initial concentration. In addition, the simultaneous reduction of Cr(VI) and decolorization of acid orange (AO) with DGD were also fulfilled. Furthermore, the energy efficiency for Cr(VI) reduction with DGD was calculated and compared with those in photocatalysis and other glow discharge reactor

Characterization of U(VI)-carbonato ternary complexes on hematite: EXAFS and electrophoretic mobility measurements

Science.gov (United States)

Bargar, John R.; Reitmeyer, Rebecca; Lenhart, John J.; Davis, James A.

2000-01-01

We have measured U(VI) adsorption on hematite using EXAFS spectroscopy and electrophoresis under conditions relevant to surface waters and aquifers (0.01 to 10 μM dissolved uranium concentrations, in equilibrium with air, pH 4.5 to 8.5). Both techniques suggest the existence of anionic U(VI)-carbonato ternary complexes. Fits to EXAFS spectra indicate that U(VI) is simultaneously coordinated to surface FeO6 octahedra and carbonate (or bicarbonate) ligands in bidentate fashions, leading to the conclusion that the ternary complexes have an inner-sphere metal bridging (hematite-U(VI)-carbonato) structure. Greater than or equal to 50% of adsorbed U(VI) was comprised of monomeric hematite-U(VI)-carbonato ternary complexes, even at pH 4.5. Multimeric U(VI) species were observed at pH ≥ 6.5 and aqueous U(VI) concentrations approximately an order of magnitude more dilute than the solubility of crystalline β-UO2(OH)2. Based on structural constraints, these complexes were interpreted as dimeric hematite-U(VI)-carbonato ternary complexes. These results suggest that Fe-oxide-U(VI)-carbonato complexes are likely to be important transport-limiting species in oxic aquifers throughout a wide range of pH values.

Étude de l’évolution de la teneur en chrome hexavalent dans le cuir, influence des conditions de fabrication et importance des facteurs environnementaux

OpenAIRE

Fontaine , Mathilde

2017-01-01

Currently, 80 to 85% of leather is tanned with chrome. This process allows to obtain excellent physico-mechanical properties with optimum economic conditions. The chromium salts in trivalent form used in the manufacturing of leather are not harmful; however under some conditions and associated with other substances, trivalent chromium can be transformed into hexavalent chromium, highly allergenic and potentially harmful to the health of the consumer. Since 1st May 2015, the presence of hexava...

Extraction kinetics of uranium (VI) with polyurethane foam

International Nuclear Information System (INIS)

Huang, Ting-Chia; Chen, Dong-Hwang; Huang, Shius-Dong; Huang, Ching-Tsven; Shieh, Mu-Chang.

1993-01-01

The extraction kinetics of uranium(VI) from aqueous nitrate solution with polyether-based polyurethane foam was investigated in a batch reactor with automatic squeezing. The extraction curves of uranium(VI) concentration in solution vs. extraction time exhibited a rather rapid exponential decay within the first few minutes, followed by a slower exponential decay during the remaining period. This phenomenon can be attributed to the presence of two-phase structure, hard segment domains and soft segment matrix in the polyurethane foam. A two-stage rate model expressed by a superposition of two exponential curves was proposed, according to which the experimental data were fitted by an optimization method. The extraction rate of uranium (VI) was also found to increase with increasing temperature, nitrate concentration, and hydration of the cation of nitrate salt. (author)

Determination of Cr2O3 in chrome-tanned leather by radionuclide-excited X-ray fluorescence analysis

International Nuclear Information System (INIS)

Melich, M.; Palagyi, S.; Kern, M.

1989-01-01

Preliminary results on the determination of Cr 2 O 3 in chrome-tanned leather by measuring the content of Cr by means of radionuclide-excited XRF analysis are reported. For excitation a 3.7 GBq 238 Pu source was used and the characteristic K X-rays of Cr were detected with a planar Si(Li) detector. Both smooth and rough sides of the leather were analyzed directly or with a pair of V/Ti balanced filters. A fairly good correlation was found between Cr Kx counts of the rough side and the Cr 2 O 3 concentrations determined chemically in the range of 3.5 to 6.0% Cr 2 O 3 . The method renders possible a rapid and non-destructive determination of Cr 2 O 3 in various leather samples. (author)

Adsorption of Cr(VI and Speciation of Cr(VI and Cr(III in Aqueous Solutions Using Chemically Modified Chitosan

Directory of Open Access Journals (Sweden)

ChunYuan Tao

2012-05-01

Full Text Available A new type of grafting chitosan (CTS was synthesized using 2-hydroxyethyl- trimethyl ammonium chloride (HGCTS. The adsorption of Cr(VI on HGCTS was studied. The effect factors on adsorption and the adsorption mechanism were considered. The results indicated that the HGCTS could concentrate and separate Cr(VI at pH 4.0; the adsorption equilibrium time was 80 min; the maximum adsorption capacity was 205 mg/g. The adsorption isotherm and kinetics were investigated, equilibrium data agreed very well with the Langmuir model and the pseudo second-order model could describe the adsorption process better than the pseudo first-order model. A novel method for speciation of Cr(VI and Cr(III in environmental water samples has been developed using HGCTS as adsorbent and FAAS as determination means. The detection limit of this method was 20 ng/L, the relatively standard deviation was 1.2% and the recovery was 99%~105%.

Wavelengths and energy levels of I V and I VI

International Nuclear Information System (INIS)

Kaufman, V.; Sugar, J.; Joshi, Y.N.

1988-01-01

The spectra of iodine were photographed in the 139--1500-Aat;O region on various spectrographs. Earlier analyses of I V and I VI were revised and extended. For I V 26 lines were classified, and for I VI 35 lines were classified. Ionization energies have been estimated to be 415 510 atm≅ 300 cm -1 (51.52 atm≅ 0.04 eV) and 599 800 atm≅ 3 000 cm -1 (74.37 atm≅ 0.37 eV) for I V and I VI, respectively

Group ib organometallic chemistry. XXXIV. Thermal behaviour and chemical reactivity of tetranuclear Me2N-substituted diarypropenylcopper-copper anion (Vi2Cu4X2) and mixed diarylpropenyl/organocopper (Vi2Cu4R2) compounds

NARCIS (Netherlands)

Hoedt, R.W.M. ten; Koten, G. van; Noltes, J.G.

1980-01-01

Thermal decomposition of configurationally pure 1,2-diarylpropenylcopper compounds Z-Vi2CU4Br2 and Z-Vi2Cu4R2 [Vi = (2-Me2NC6H4)C=C(Me)-(C6H4Me-4), R = 2-Me2NC6H4 or 4-MeC6H4CC] predominantly results in the formation of ViH. In contrast, only dimers (ViVi) were formed on thermolysis of (Z-ViCu2OTf)η

Intervening O vi Quasar Absorption Systems at Low Redshift: A Significant Baryon Reservoir.

Science.gov (United States)

Tripp; Savage; Jenkins

2000-05-01

Far-UV echelle spectroscopy of the radio-quiet QSO H1821+643 (zem=0.297), obtained with the Space Telescope Imaging Spectrograph (STIS) at approximately 7 km s-1 resolution, reveals four definite O vi absorption-line systems and one probable O vi absorber at 0.15quasar in redshift; these are likely intervening systems unrelated to the background QSO. In the case of the strong O vi system at zabs=0.22497, multiple components are detected in Si iii and O vi as well as H i Lyman series lines, and the differing component velocity centroids and b-values firmly establish that this is a multiphase absorption system. A weak O vi absorber is detected at zabs=0.22637, i.e., offset by approximately 340 km s-1 from the zabs=0.22497 system. Lyalpha absorption is detected at zabs=0.22613, but no Lyalpha absorption is significantly detected at 0.22637. Other weak O vi absorbers at zabs=0.24531 and 0.26659 and the probable O vi system at 0.21326 have widely diverse O vi/H i column density ratios with N(O vi)/N(H i) ranging from vi absorbers with rest equivalent width greater than 30 mÅ in the H1821+643 spectrum is remarkably high, dN&solm0;dz approximately 48, which implies with a high (90%) confidence that it is greater than 17 in the low-redshift intergalactic medium. We conservatively estimate that the cosmological mass density of the O vi systems is Omegab(Ovi&parr0; greater, similar0.0008 h-175. With an assumed metallicity of 1/10 solar and a conservative assumption that the fraction of oxygen in the O vi ionization stage is 0.2, we obtain Omegab(Ovi&parr0; greater, similar0.004 h-175. This is comparable to the combined cosmological mass density of stars and cool gas in galaxies and X-ray-emitting gas in galaxy clusters at low redshift.

On halide derivatives of rare-earth metal(III) oxidomolybdates(VI) and -tungstates(VI)

International Nuclear Information System (INIS)

Schleid, Thomas; Hartenbach, Ingo

2016-01-01

Halide derivatives of rare-earth metal(III) oxidomolybdates(VI) have been investigated comprehensively over the last decade comprising the halogens fluorine, chlorine, and bromine. Iodide-containing compounds are so far unknown. The simple composition REXMoO 4 (RE=rare-earth element, X=halogen) is realized for X=F almost throughout the complete lanthanide series as well as for yttrium. While ytterbium and lutetium do not form any fluoride derivative, for lanthanum, only a fluoride-deprived compound with the formula La 3 FMo 4 O 16 is realized. Moreover, molybdenum-rich compounds with the formula REXMo 2 O 7 are also known for yttrium and the smaller lanthanoids. For X=Cl the composition REClMoO 4 is known for yttrium and the whole lanthanide series, although, four different structure types were identified. Almost the same holds for X=Br, however, only two different structure types are realized in this class of compounds. In the case of halide derivatives of rare-earth metal(III) oxidotungstates(VI) the composition REXWO 4 is found for chlorides and bromides only, so far. Due to the similar size of Mo 6+ and W 6+ cations, the structures found for the tungstates are basically the same as for the molybdates. With the larger lanthanides, the representatives for both chloride and bromide derivates exhibit similar structural motifs as seen in the molybdates, however, the crystal structure cannot be determined reliably. In case of the smaller lanthanoids, the chloride derivatives are isostructural with the respective molybdates, although the existence ranges differ slightly. The same is true for rare-earth metal(III) bromide oxidotungstates(VI).

Uranium(VI) Reduction by Nanoscale Zerovalent Iron in Anoxic Batch Systems

International Nuclear Information System (INIS)

Yan, Sen; Hua, Bin; Bao, Zhengyu; Yang, John; Liu, Chongxuan; Deng, Baolin

2010-01-01

This study investigated the influences of pH, bicarbonate, and calcium on U(VI) adsorption and reduction by synthetic nanosize zero valent iron (nano Fe 0 ) particles under an anoxic condition. The results showed that about 87.1%, 82.7% and 78.3% of U(VI) could be reduced within 96 hours in the presence of 10 mM bicarbonate at pHs 6.92, 8.03 and 9.03, respectively. The rates of U(VI) reduction and adsorption by nano Fe 0 , however, varied significantly with increasing pH and concentrations of bicarbonate and/or calcium. Solid phase analysis by X-ray photoelectron spectroscopy confirmed the formation of UO 2 and iron (hydr)oxides as a result of the redox interactions between adsorbed U(VI) and nano Fe 0 . This study highlights the potential important role of groundwater chemical composition in controlling the rates of U(VI) reductive immobilization using nano Fe 0 in subsurface environments.

Extractive behavior of U(VI) in the paraffin soluble ionic liquid

International Nuclear Information System (INIS)

Rama, R.; Kumaresan, R.; Venkatesan, K.A.; Antony, M.P.; Vasudeva Rao, P.R.

2013-01-01

An Aliquat-336 based ionic liquid namely, tri-n-octylmethylammonium bis(2-ethylhexyl)phosphate ((A3636) + (DEHP) - ) was prepared and studied for the extraction of U(VI) from nitric acid medium. Since the ionic liquid, (A336) + (DEHP) - , was miscible in n-dodecane (n-DD), the extraction of U(VI) in the solution of tri-n-butylphosphate (TBP) in n-DD, was investigated in the presence of small concentrations of ionic liquid. The distribution ratio of U(VI) in 0.3 M (A336) + (DEHP) - /n-DD decreased with increase in the concentration of nitric acid. The effect of concentration of TBP, ionic liquid nitric acid and nitrate ion on the extraction of U(VI) in ionic liquid medium was studied. The mechanistic aspect of extraction was investigated by the slope analysis of the extraction data. The studies indicated the feasibility of modifying the extractive properties of U(VI) in TBP/n-DD using ionic liquid. (author)

Gravimetric determination of uranium(VI) and thorium(IV) with substituted pyrazolones

International Nuclear Information System (INIS)

Arora, H.C.; Rao, G.N.

1981-01-01

4-Acylpyrazolones like 1-phenyl-3-methyl-4-benzoyl-5-pyrazolone (PMBP), 1-phenyl-3-methyl-4-p-nitrobenzoyl-5-pyrazolone (PMNP) and 1-phenyl-3-methyl-4-(3,5 dinitrobenzoyl)-5-pyrazolone (PMDP) have been synthesized and developed as gravimetric reagents for the determination of U(VI) and Th(IV). Uranium(VI) is almost quantitatively precipitated with PMBP, PMNP, and PMDP at pH 2.20, 1.85 and 1.70 respectively. The pH values for the complete precipitation of thorium(IV) with PMBP, PMNP and PMDP are 2.90, 2.75 and 2.50 respectively. PMBP has proved to be an efficient ligand for gravimetric determination of U(VI) by direct weighing method after drying at 100 +- 10 deg C. The percentage relative error varies from 0.4 to 1.6 in the determination of U(VI) by this method. The effect of a number of interfering ions on the precipitation of U(VI) by PMBP has been reported. (author)

ViCTree: An automated framework for taxonomic classification from protein sequences.

Science.gov (United States)

Modha, Sejal; Thanki, Anil; Cotmore, Susan F; Davison, Andrew J; Hughes, Joseph

2018-02-20

The increasing rate of submission of genetic sequences into public databases is providing a growing resource for classifying the organisms that these sequences represent. To aid viral classification, we have developed ViCTree, which automatically integrates the relevant sets of sequences in NCBI GenBank and transforms them into an interactive maximum likelihood phylogenetic tree that can be updated automatically. ViCTree incorporates ViCTreeView, which is a JavaScript-based visualisation tool that enables the tree to be explored interactively in the context of pairwise distance data. To demonstrate utility, ViCTree was applied to subfamily Densovirinae of family Parvoviridae. This led to the identification of six new species of insect virus. ViCTree is open-source and can be run on any Linux- or Unix-based computer or cluster. A tutorial, the documentation and the source code are available under a GPL3 license, and can be accessed at http://bioinformatics.cvr.ac.uk/victree_web/. sejal.modha@glasgow.ac.uk.

Contribution of Extracellular Polymeric Substances from Shewanella sp. HRCR-1 Biofilms to U(VI) Immobilization

Energy Technology Data Exchange (ETDEWEB)

Cao, Bin; Ahmed, B.; Kennedy, David W.; Wang, Zheming; Shi, Liang; Marshall, Matthew J.; Fredrickson, Jim K.; Isern, Nancy G.; Majors, Paul D.; Beyenal, Haluk

2011-06-05

The goal of this study was to quantify the contribution of extracellular polymeric substances (EPS) in U(VI) immobilization by Shewanella sp. HRCR-1. Through comparison of U(VI) immobilization using cells with bound EPS (bEPS) and cells without EPS, we showed that i) bEPS from Shewanella sp. HRCR-1 biofilms contributed significantly to U(VI) immobilization, especially at low initial U(VI) concentrations, through both sorption and reduction; ii) bEPS could be considered as a functional extension of the cells for U(VI) immobilization and they likely play more important roles at initial U(VI) concentrations; and iii) U(VI) reduction efficiency was found to be dependent upon initial U(VI) concentration and the efficiency decreased at lower concentrations. To quantify relative contribution of sorption and reduction in U(VI) immobilization by EPS fractions, we isolated loosely associated EPS (laEPS) and bEPS from Shewanella sp. HRCR-1 biofilms grown in a hollow fiber membrane biofilm reactor and tested their reactivity with U(V). We found that, when in reduced form, the isolated cell-free EPS fractions could reduce U(VI). Polysaccharides in the EPS likely contributed to U(VI) sorption and dominated reactivity of laEPS while redox active components (e.g., outer membrane c-type cytochromes), especially in bEPS, might facilitate U(VI) reduction.

Differential Killing of Salmonella enterica Serovar Typhi by Antibodies Targeting Vi and Lipopolysaccharide O:9 Antigen.

Directory of Open Access Journals (Sweden)

Peter J Hart

Full Text Available Salmonella enterica serovar Typhi expresses a capsule of Vi polysaccharide, while most Salmonella serovars, including S. Enteritidis and S. Typhimurium, do not. Both S. Typhi and S. Enteritidis express the lipopolysaccharide O:9 antigen, yet there is little evidence of cross-protection from anti-O:9 antibodies. Vaccines based on Vi polysaccharide have efficacy against typhoid fever, indicating that antibodies against Vi confer protection. Here we investigate the role of Vi capsule and antibodies against Vi and O:9 in antibody-dependent complement- and phagocyte-mediated killing of Salmonella. Using isogenic Vi-expressing and non-Vi-expressing derivatives of S. Typhi and S. Typhimurium, we show that S. Typhi is inherently more sensitive to serum and blood than S. Typhimurium. Vi expression confers increased resistance to both complement- and phagocyte-mediated modalities of antibody-dependent killing in human blood. The Vi capsule is associated with reduced C3 and C5b-9 deposition, and decreased overall antibody binding to S. Typhi. However, purified human anti-Vi antibodies in the presence of complement are able to kill Vi-expressing Salmonella, while killing by anti-O:9 antibodies is inversely related to Vi expression. Human serum depleted of antibodies to antigens other than Vi retains the ability to kill Vi-expressing bacteria. Our findings support a protective role for Vi capsule in preventing complement and phagocyte killing of Salmonella that can be overcome by specific anti-Vi antibodies, but only to a limited extent by anti-O:9 antibodies.

Differential Killing of Salmonella enterica Serovar Typhi by Antibodies Targeting Vi and Lipopolysaccharide O:9 Antigen.

Science.gov (United States)

Hart, Peter J; O'Shaughnessy, Colette M; Siggins, Matthew K; Bobat, Saeeda; Kingsley, Robert A; Goulding, David A; Crump, John A; Reyburn, Hugh; Micoli, Francesca; Dougan, Gordon; Cunningham, Adam F; MacLennan, Calman A

2016-01-01

Salmonella enterica serovar Typhi expresses a capsule of Vi polysaccharide, while most Salmonella serovars, including S. Enteritidis and S. Typhimurium, do not. Both S. Typhi and S. Enteritidis express the lipopolysaccharide O:9 antigen, yet there is little evidence of cross-protection from anti-O:9 antibodies. Vaccines based on Vi polysaccharide have efficacy against typhoid fever, indicating that antibodies against Vi confer protection. Here we investigate the role of Vi capsule and antibodies against Vi and O:9 in antibody-dependent complement- and phagocyte-mediated killing of Salmonella. Using isogenic Vi-expressing and non-Vi-expressing derivatives of S. Typhi and S. Typhimurium, we show that S. Typhi is inherently more sensitive to serum and blood than S. Typhimurium. Vi expression confers increased resistance to both complement- and phagocyte-mediated modalities of antibody-dependent killing in human blood. The Vi capsule is associated with reduced C3 and C5b-9 deposition, and decreased overall antibody binding to S. Typhi. However, purified human anti-Vi antibodies in the presence of complement are able to kill Vi-expressing Salmonella, while killing by anti-O:9 antibodies is inversely related to Vi expression. Human serum depleted of antibodies to antigens other than Vi retains the ability to kill Vi-expressing bacteria. Our findings support a protective role for Vi capsule in preventing complement and phagocyte killing of Salmonella that can be overcome by specific anti-Vi antibodies, but only to a limited extent by anti-O:9 antibodies.

Bicarbonate Impact on U(VI) Bioreduction in a Shallow Alluvial Aquifer

Energy Technology Data Exchange (ETDEWEB)

Long, Philip E.; Williams, Kenneth H.; Davis, James A.; Fox, Patricia M.; Wilkins, Michael J.; Yabusaki, Steven B.; Fang, Yilin; Waichler, Scott R.; Berman, Elena S.; Gupta, Manish; Chandler, Darrell P.; Murray, Christopher J.; Peacock, Aaron D.; Giloteaux, L.; Handley, Kim M.; Lovley, Derek R.; Banfield, Jillian F.

2015-02-01

Field-scale biostimulation and desorption tracer experiments conducted in a uranium (U) contaminated, shallow alluvial aquifer have provided insight into the coupling of microbiology, biogeochemistry, and hydrogeology that control U mobility in the subsurface. Initial experiments successfully tested the concept that Fe-reducing bacteria such as Geobacter sp. could enzymatically reduce soluble U(VI) to insoluble U(IV) during in situ electron donor amendment (Anderson et al. 2003, Williams et al. 2011). In parallel, in situ desorption tracer tests using bicarbonate amendment demonstrated rate-limited U(VI) desorption (Fox et al. 2012). These results and prior laboratory studies underscored the importance of enzymatic U(VI)-reduction and suggested the ability to combine desorption and bioreduction of U(VI). Here we report the results of a new field experiment in which bicarbonate-promoted uranium desorption and acetate amendment were combined and compared to an acetate amendment-only experiment in the same experimental plot. Results confirm that bicarbonate amendment to alluvial aquifer desorbs U(VI) and increases the abundance of Ca-uranyl-carbonato complexes. At the same time, that the rate of acetate-promoted enzymatic U(VI) reduction was greater in the presence of added bicarbonate in spite of the increased dominance of Ca-uranyl-carbonato aqueous complexes. A model-simulated peak rate of U(VI) reduction was ~3.8 times higher during acetate-bicarbonate treatment than under acetate-only conditions. Lack of consistent differences in microbial community structure between acetate-bicarbonate and acetate-only treatments suggest that a significantly higher rate of U(VI) reduction the bicarbonate-impacted sediment may be due to a higher intrinsic rate of microbial reduction induced by elevated concentrations of the bicarbonate oxyanion. The findings indicate that bicarbonate amendment may be useful in improving the engineered bioremediation of uranium in aquifers.

Bicarbonate impact on U(VI) bioreduction in a shallow alluvial aquifer

Science.gov (United States)

Long, Philip E.; Williams, Kenneth H.; Davis, James A.; Fox, Patricia M.; Wilkins, Michael J.; Yabusaki, Steven B.; Fang, Yilin; Waichler, Scott R.; Berman, Elena S. F.; Gupta, Manish; Chandler, Darrell P.; Murray, Chris; Peacock, Aaron D.; Giloteaux, Ludovic; Handley, Kim M.; Lovley, Derek R.; Banfield, Jillian F.

2015-02-01

Field-scale biostimulation and desorption tracer experiments conducted in a uranium (U) contaminated, shallow alluvial aquifer have provided insight into the coupling of microbiology, biogeochemistry, and hydrogeology that control U mobility in the subsurface. Initial experiments successfully tested the concept that Fe-reducing bacteria such as Geobacter sp. could enzymatically reduce soluble U(VI) to insoluble U(IV) during in situ electron donor amendment (Anderson et al., 2003; Williams et al., 2011). In parallel, in situ desorption tracer tests using bicarbonate amendment demonstrated rate-limited U(VI) desorption (Fox et al., 2012). These results and prior laboratory studies underscored the importance of enzymatic U(VI)-reduction and suggested the ability to combine desorption and bioreduction of U(VI). Here we report the results of a new field experiment in which bicarbonate-promoted uranium desorption and acetate amendment were combined and compared to an acetate amendment-only experiment in the same experimental plot. Results confirm that bicarbonate amendment to alluvial aquifer sediments desorbs U(VI) and increases the abundance of Ca-uranyl-carbonato complexes. At the same time, the rate of acetate-promoted enzymatic U(VI) reduction was greater in the presence of added bicarbonate in spite of the increased dominance of Ca-uranyl-carbonato aqueous complexes. A model-simulated peak rate of U(VI) reduction was ∼3.8 times higher during acetate-bicarbonate treatment than under acetate-only conditions. Lack of consistent differences in microbial community structure between acetate-bicarbonate and acetate-only treatments suggest that a significantly higher rate of U(VI) reduction in the bicarbonate-impacted sediment may be due to a higher intrinsic rate of microbial reduction induced by elevated concentrations of the bicarbonate oxyanion. The findings indicate that bicarbonate amendment may be useful in improving the engineered bioremediation of uranium in

Review of carcinogenicity of hexavalent chrome and proposal of revising approval standards for an occupational cancers in Korea.

Science.gov (United States)

Kim, Jungwon; Seo, Sangyun; Kim, Yangho; Kim, Dae Hwan

2018-01-01

The objective of this study is to suggest revised recognition standards for occupational disease due to chromium (VI) by reflecting recent domestic and international research works and considering domestic exposure status with respect to target organs, exposure period, and cumulative exposure dose in relation to the chromium (VI)-induced occupational disease compensation. In this study, the reports published by major international institutions such as World Health Organization (WHO) International Agency for Research on Cancer (IARC) (2012), Occupational Safety and Health Administration (OSHA) (2006), National Institute for Occupational Safety and Health (NIOSH) (2013), American Conference of Governmental Industrial Hygienists (ACGIH) (2004), National Toxicology Program (NTP) (2014), and Agency for Toxic Substances and Disease Registry (ASTDR) (2012) were reviewed and the recent research works searched by PubMed were summarized. Considering the recent research works and the domestic situation, only lung cancer is conserved in the legislative bill in relation to chromium (VI), and the exposure period is not included in the bill. Nasal and paranasal sinus cancer was excluded from the list of cancers that are compensated as the chromium (VI)- induced occupational disease, while lung cancer remains in the list. In the view of legislative unity, considering the fact that only the cancers having sufficient evidence are included in the conventional list of cancers compensated as occupational disease, nasal and paranasal sinus cancer having limited evidence were excluded from the list.The exposure period was also removed from the legislative bill due to the insufficient evidence. Recent advices in connection with cumulative exposure dose were proposed, and other considerable points were provided with respect to individual occupational relevance. It is suggested that the current recognition standard which is "Lung cancer or nasal and paranasal sinus cancer caused by exposure

Mechanism of uranium (VI) removal by two anaerobic bacterial communities

Energy Technology Data Exchange (ETDEWEB)

Martins, Monica [Centro de Ciencias do Mar, Universidade do Algarve, FCT-DQF (edificio 8), Campus de Gambelas, 8005-139 Faro (Portugal); Faleiro, Maria Leonor [IBB - Centro de Biomedicina Molecular e Estrutural, Universidade do Algarve, FCT, Campus de Gambelas, 8005-139 Faro (Portugal); Costa, Ana M. Rosa da [Centro de Investigacao em Quimica do Algarve, Universidade do Algarve, FCT, DQF, Campus de Gambelas, 8005-139 Faro (Portugal); Chaves, Sandra; Tenreiro, Rogerio [Universidade de Lisboa, Faculdade de Ciencias, Centro de Biodiversidade, Genomica Integrativa e Funcional (BioFIG), Campus de FCUL, Campo Grande, 1749-016 Lisboa (Portugal); Matos, Antonio Pedro [Servico de Anatomia Patologica, Hospital Curry Cabral, Lisboa (Portugal); Costa, Maria Clara, E-mail: mcorada@ualg.pt [Centro de Ciencias do Mar, Universidade do Algarve, FCT-DQF (edificio 8), Campus de Gambelas, 8005-139 Faro (Portugal)

2010-12-15

The mechanism of uranium (VI) removal by two anaerobic bacterial consortia, recovered from an uncontaminated site (consortium A) and other from an uranium mine (consortium U), was investigated. The highest efficiency of U (VI) removal by both consortia (97%) occurred at room temperature and at pH 7.2. Furthermore, it was found that U (VI) removal by consortium A occurred by enzymatic reduction and bioaccumulation, while the enzymatic process was the only mechanism involved in metal removal by consortium U. FTIR analysis suggested that after U (VI) reduction, U (IV) could be bound to carboxyl, phosphate and amide groups of bacterial cells. Phylogenetic analysis of 16S rRNA showed that community A was mainly composed by bacteria closely related to Sporotalea genus and Rhodocyclaceae family, while community U was mainly composed by bacteria related to Clostridium genus and Rhodocyclaceae family.

Mechanism of uranium (VI) removal by two anaerobic bacterial communities

International Nuclear Information System (INIS)

Martins, Monica; Faleiro, Maria Leonor; Costa, Ana M. Rosa da; Chaves, Sandra; Tenreiro, Rogerio; Matos, Antonio Pedro; Costa, Maria Clara

2010-01-01

The mechanism of uranium (VI) removal by two anaerobic bacterial consortia, recovered from an uncontaminated site (consortium A) and other from an uranium mine (consortium U), was investigated. The highest efficiency of U (VI) removal by both consortia (97%) occurred at room temperature and at pH 7.2. Furthermore, it was found that U (VI) removal by consortium A occurred by enzymatic reduction and bioaccumulation, while the enzymatic process was the only mechanism involved in metal removal by consortium U. FTIR analysis suggested that after U (VI) reduction, U (IV) could be bound to carboxyl, phosphate and amide groups of bacterial cells. Phylogenetic analysis of 16S rRNA showed that community A was mainly composed by bacteria closely related to Sporotalea genus and Rhodocyclaceae family, while community U was mainly composed by bacteria related to Clostridium genus and Rhodocyclaceae family.

Cr(VI) occurrence and geochemistry in water from public-supply wells in California

Science.gov (United States)

Izbicki, John; Wright, Michael; Seymour, Whitney A.; McCleskey, R. Blaine; Fram, Miranda S.; Belitz, Kenneth; Esser, Bradley K.

2015-01-01

Hexavalent chromium, Cr(VI), in 918 wells sampled throughout California between 2004 and 2012 by the Groundwater Ambient Monitoring and Assessment-Priority Basin Project (GAMA-PBP) ranged from less than the study reporting limit of 1 microgram per liter (μg/L) to 32 μg/L. Statewide, Cr(VI) was reported in 31 percent of wells and equaled or exceeded the recently established (2014) California Maximum Contaminant Level (MCL) for Cr(VI) of 10 μg/L in 4 percent of wells. Cr(VI) data collected for regulatory purposes overestimated Cr(VI) occurrence compared to spatially-distributed GAMA-PBP data. Ninety percent of chromium was present as Cr(VI), which was detected more frequently and at higher concentrations in alkaline (pH ≥ 8), oxic water; and more frequently in agricultural and urban land uses compared to native land uses. Chemical, isotopic (tritium and carbon-14), and noble-gas data show high Cr(VI) in water from wells in alluvial aquifers in the southern California deserts result from long groundwater-residence times and geochemical reactions such as silicate weathering that increase pH, while oxic conditions persist. High Cr(VI) in water from wells in alluvial aquifers along the west-side of the Central Valley results from high-chromium in source rock eroded to form those aquifers, and areal recharge processes (including irrigation return) that can mobilize chromium from the unsaturated zone. Cr(VI) co-occurred with oxyanions having similar chemistry, including vanadium, selenium, and uranium. Cr(VI) was positively correlated with nitrate, consistent with increased concentrations in areas of agricultural land use and mobilization of chromium from the unsaturated zone by irrigation return.

Oxidation of ciprofloxacin and enrofloxacin by ferrate(VI): Products identification, and toxicity evaluation

International Nuclear Information System (INIS)

Yang, Bin; Kookana, Rai S.; Williams, Mike; Ying, Guang-Guo; Du, Jun; Doan, Hai; Kumar, Anupama

2016-01-01

Ferrate(VI) (Fe(VI)) has been known to react with emerging organic contaminants containing electron-rich organic moieties, such as phenols, anilines, olefins, reduced sulfur and deprotonated amines. Oxidation of fluoroquinolone antibiotics, ciprofloxacin (CIP) and enrofloxacin (ENR), by Fe(VI) were investigated for their reaction products and toxicity changes as well as biodegradability of these products. Ten products were identified for both CIP and ENR reactions with Fe(VI) using a high-resolution accurate-mass Orbitrap mass analyzer. Structural changes to the CIP and ENR molecule included dealkylation, formation of alcohols and amides in piperazine ring and oxygen transfer to the double bond in quinolone structure. An enamine formation mechanism was tentatively proposed to facilitate the interpretation of CIP and ENR oxidation pathways. Toxicity evaluation using Microbial Assay for toxicity Risk Assessment (MARA) bioassay indicated that Fe(VI) oxidation products of CIP and ENR contributed negligible antibacterial potency and Fe(VI) oxidation treatment can remove the residual toxicity of CIP and ENR impacted source waters. The Fe(VI) oxidation treatment resulted in formation of relatively more biodegradable products (based on in silico assessment) than their corresponding parent compounds. The results showed that Fe(VI) has a good potential to degrade fluoroquinolone antibiotics and their antimicrobial potency in natural waters.

Oxidation of ciprofloxacin and enrofloxacin by ferrate(VI): Products identification, and toxicity evaluation

Energy Technology Data Exchange (ETDEWEB)

Yang, Bin, E-mail: Bin.Yang@csiro.au [CSIRO Land and Water, Waite Campus, PMB 2, Glen Osmond, South Australia 5064 (Australia); Kookana, Rai S.; Williams, Mike [CSIRO Land and Water, Waite Campus, PMB 2, Glen Osmond, South Australia 5064 (Australia); Ying, Guang-Guo [State Key Laboratory of Organic Geochemistry, Guangzhou Institute of Geochemistry, Chinese Academy of Sciences, Guangzhou 510640 (China); Du, Jun; Doan, Hai; Kumar, Anupama [CSIRO Land and Water, Waite Campus, PMB 2, Glen Osmond, South Australia 5064 (Australia)

2016-12-15

Ferrate(VI) (Fe(VI)) has been known to react with emerging organic contaminants containing electron-rich organic moieties, such as phenols, anilines, olefins, reduced sulfur and deprotonated amines. Oxidation of fluoroquinolone antibiotics, ciprofloxacin (CIP) and enrofloxacin (ENR), by Fe(VI) were investigated for their reaction products and toxicity changes as well as biodegradability of these products. Ten products were identified for both CIP and ENR reactions with Fe(VI) using a high-resolution accurate-mass Orbitrap mass analyzer. Structural changes to the CIP and ENR molecule included dealkylation, formation of alcohols and amides in piperazine ring and oxygen transfer to the double bond in quinolone structure. An enamine formation mechanism was tentatively proposed to facilitate the interpretation of CIP and ENR oxidation pathways. Toxicity evaluation using Microbial Assay for toxicity Risk Assessment (MARA) bioassay indicated that Fe(VI) oxidation products of CIP and ENR contributed negligible antibacterial potency and Fe(VI) oxidation treatment can remove the residual toxicity of CIP and ENR impacted source waters. The Fe(VI) oxidation treatment resulted in formation of relatively more biodegradable products (based on in silico assessment) than their corresponding parent compounds. The results showed that Fe(VI) has a good potential to degrade fluoroquinolone antibiotics and their antimicrobial potency in natural waters.

A Salmonella Typhimurium-Typhi genomic chimera: a model to study Vi polysaccharide capsule function in vivo.

Directory of Open Access Journals (Sweden)

Angela M Jansen

2011-07-01

Full Text Available The Vi capsular polysaccharide is a virulence-associated factor expressed by Salmonella enterica serotype Typhi but absent from virtually all other Salmonella serotypes. In order to study this determinant in vivo, we characterised a Vi-positive S. Typhimurium (C5.507 Vi(+, harbouring the Salmonella pathogenicity island (SPI-7, which encodes the Vi locus. S. Typhimurium C5.507 Vi(+ colonised and persisted in mice at similar levels compared to the parent strain, S. Typhimurium C5. However, the innate immune response to infection with C5.507 Vi(+ and SGB1, an isogenic derivative not expressing Vi, differed markedly. Infection with C5.507 Vi(+ resulted in a significant reduction in cellular trafficking of innate immune cells, including PMN and NK cells, compared to SGB1 Vi(- infected animals. C5.507 Vi(+ infection stimulated reduced numbers of TNF-α, MIP-2 and perforin producing cells compared to SGB1 Vi(-. The modulating effect associated with Vi was not observed in MyD88(-/- and was reduced in TLR4(-/- mice. The presence of the Vi capsule also correlated with induction of the anti-inflammatory cytokine IL-10 in vivo, a factor that impacted on chemotaxis and the activation of immune cells in vitro.

Paul Scherrer Institute Scientific and Technical Report 1999. Volume VI: Large Research Facilities

Energy Technology Data Exchange (ETDEWEB)

Foroughi, Fereydoun; Bercher, Renate; Buechli, Carmen; Meyer, Rosa [eds.

2000-07-01

The department GFA (Grossforschungsanlagen, Large Research Facilities) has been established in October 1998. Its main duty is operation, maintenance and development of the PSI accelerators, the spallation neutron source and the beam transport systems for pions and muons. A large effort of this group concerns the planning and co-ordination of new projects like e.g. the assembly of the synchrotron light source (SLS), design studies of a new proton therapy facility, the ultracold neutron source and a new intensive secondary beam line for low energy muons. A large fraction of this report is devoted to research especially in the field of materials Science. The studies include large scale molecular dynamics computer simulations on the elastic and plastic behavior of nanostructured metals, complemented by experimental mechanical testing using micro-indentation and miniaturized tensile testing, as well as microstructural characterisation and strain field mapping of metallic coatings and thin ceramic layers, the latter done with synchrotron radiation.

Paul Scherrer Institute Scientific and Technical Report 1999. Volume VI: Large Research Facilities

International Nuclear Information System (INIS)

Foroughi, Fereydoun; Bercher, Renate; Buechli, Carmen; Meyer, Rosa

2000-01-01

The department GFA (Grossforschungsanlagen, Large Research Facilities) has been established in October 1998. Its main duty is operation, maintenance and development of the PSI accelerators, the spallation neutron source and the beam transport systems for pions and muons. A large effort of this group concerns the planning and co-ordination of new projects like e.g. the assembly of the synchrotron light source (SLS), design studies of a new proton therapy facility, the ultracold neutron source and a new intensive secondary beam line for low energy muons. A large fraction of this report is devoted to research especially in the field of materials Science. The studies include large scale molecular dynamics computer simulations on the elastic and plastic behavior of nanostructured metals, complemented by experimental mechanical testing using micro-indentation and miniaturized tensile testing, as well as microstructural characterisation and strain field mapping of metallic coatings and thin ceramic layers, the latter done with synchrotron radiation

Uranium(VI) adsorption properties of a chelating resin containing polyamine-substituted methylphosphonic acid moiety

International Nuclear Information System (INIS)

Matsuda, Masaaki; Akiyoshi, Yoshirou

1991-01-01

Uranium(VI) adsorption and desorption properties of a chelating resin containing polyamine-substituted methylphosphonic acid moiety of 2.29 mmol/g-resin (APA) were examined. Uranium(VI) adsorption properties of several ion exchange resins and extractant agents which were known as excellent adsorbents for uranium(VI), were examined together for a comparison with those of APA. Uranium(VI) adsorption capacity of APA at the concentration of 100 mg·dm -3 -uranium(VI) in 100 g·dm -3 -H 2 SO 4 aq. soln., 190 g·dm -3 -H 3 PO 4 aq. soln. and uranium enriched sea water, was 0.2, 0.05 and 0.05 mmol·g -1 respectively. The adsorption capacity of APA for uranium(VI) in these solutions was larger than that of another adsorbents, except the adsorption of uranium(VI) in enriched sea water on ion exchange resin containing phosphoric acid moiety (adsorption capacity ; 0.2 mmol·g -1 ). Uranium(VI) adsorption rate on APA was high and the relation between treatment time (t : min) and uranium(VI) concentration (y : mg·dm -3 ) in 100 g·dm -3 H 2 SO 4 aq. soln. after treatment, was shown as following equation, y=20 0.048t+1.90 (0≤t≤30). The adsorbed uranium(VI) on APA was able to be eluted with a mixed aq. soln. of hydrogen peroxide and sodium hydroxide and also was able to be eluted with an aq. alkaline soln. dissolved reduction agents such as sodium sulfite and hydrazine. From these results, it was thought that uranium(VI) adsorbed on APA was eluted due to the reduction to uranium(VI) by these eluents. (author)

Development of spectrophotometric determination of beryllium in beryl minerals using chrome Azurol S

Directory of Open Access Journals (Sweden)

Hisham K. Fouad

2016-09-01

Full Text Available A developed, direct, rapid, and sensitive spectrophotometric determination of beryllium in beryl minerals with Chrome Azurol S (CAS as a chromogenic reagent was developed in the present article. The determination was performed without either solvent extraction or ion exchange separation of beryllium from its matrix. The stable 1:1 Be-CAS complex was formed instantly with duration time of at least 24 h with constant absorbance. Different parameters such as wavelengths, pH, EDTA concentration and dye concentration were studied for the optimum determination of beryllium. Interference due to presence of high aluminum concentrations was overcome by adding 5% EDTA disodium salt solution. Maximum absorbance for Be-CAS complex was performed at λmax 568 NM using acetate buffer at pH 4.6. Beer’s law was obeyed in the range from 0.02 to 9 ppm with molar absorptivity ε = 0.22 × 104 mol−1 cm−1 and an average standard deviation of 0.7. The R.S.D for 10 replicate measurements of 1 ppm Be was 1.2%.

Group IB Organometallic Chemistry XXXIV: Thermal behavior and chemical reactivity of tetranuclear Me2N-substituted diarylpropenylcopper-copper anion (Vi2Cu4X2) and mixed diarylpropenyl/organocopper (Vi2Cu4R2) compounds

NARCIS (Netherlands)

Koten, G. van; Hoedt, R.W.M. ten; Noltes, J.G.

1980-01-01

Thermal decomposition of configurationally pure 1, 2-diarylpropenylcopper compounds Z-Vi{2}CU{4}Br{2} and Z-Vi{2}Cu{4}R{2} [Vi @? (2-Me{2}NC{6}H{4})C@?C(Me)-(C{6}H{4}Me-4), R @? 2-Me{2}NC{6}H{4} or 4-MeC{6}H{4}C@?C] predominantly results in the formation of ViH. In contrast, only dimers (ViVi) were

Oxidação de microcistinas-LR em águas pelo íon ferrato(VI Aqueous oxidation of microcystin-LR by ferrate(VI

Directory of Open Access Journals (Sweden)

Sérgio João de Luca

2010-03-01

Full Text Available Toxinas de cianobactérias têm se tornado um grave problema na produção segura de água para consumo humano e animal. Técnicas convencionais de tratamento falham em atingir padrões de potabilidade. O ferrato(VI de potássio, um composto oxidante e coagulante, mostra potencialidade no tratamento de águas contaminadas. Neste trabalho, são apresentados resultados da oxidação pelo ferrato(VI de uma toxina gerada por cianobactérias, a microcistina-LR. Ensaios de cinética de oxidação e de teste de jarros mostram um valor médio de 0,012 min-1 para a constante de taxa de reação de pseudoprimeira ordem, para concentrações de MC-LR de 100 a 200 µg.L-1 na água bruta. Dosagens de 1,6 a 5,0 mg.L-1 de ferrato(VI sugerem o atendimento ao padrão de potabilidade para microcistinas, mostrando que o oxidante poderá ser empregado como coadjuvante no tratamento de água.Algae toxins are becoming a severe problem in the water treatment industry, especially for human and animal consumption. Traditional treatment processes have failed in complying with water supply standards. Potassium ferrate(VI is a powerful oxidant, disinfectant and, also, a coagulant. In this paper, the results of microcystin-LR oxidation by ferrate(VI ion are presented. Kinetic and jar tests showed a average value of 0,012 min-1 for the pseudo first order reaction rate constant, for 100 and 200 µg.L-1 concentration of MC-LR. Ferrate(VI dosages between 1.6 and 5.0 mg.L-1 suggest that water supply standards for MC-LR can be reached, which means that the oxidant may be employed as coadjuvant in water treatment.

Retention of uranium(VI) by laumontite, a fracture-filling material of granite

International Nuclear Information System (INIS)

Baik, M.H.; Lee, S.Y.; Shon, W.J.

2009-01-01

Retention of U(VI) by laumontite, a fracture-filling material of granite as investigated by conducting dynamic and batch sorption experiments in a love-box using a granite core with a natural fracture. The hydrodynamic properties of the granite core were obtained from the elution curve of a on-sorbing tracer, Br - . The elution curve of U(VI) showed a similar behavior to Br - . This reveals that the retention of U(VI) by the fracture-filling material was not significant when migrating through the fracture at a given condition. From the dynamic sorption experiment, the retardation factor R a and the distribution coefficient K a of U(VI) were obtained as about 2.9 and 0.16 cm, respectively. The distribution coefficient K d ) of U(VI) onto laumontite obtained by conducting a batch sorption experiment resulted in a small value of 2.3±0.5 mL/g. This low K d value greed with the result of the dynamic sorption experiment. For the distribution of uranium on the granite surface investigated by an X-ray image mapping, the fracture region filled with laumontite showed a relatively lower content of uranium compared to the surrounding granite surface. Thus, the low retention of U(VI) by the fracture-filling material can be explained by following two mechanisms. One is that U(VI) exists as anionic uranyl hydroxides or uranyl carbonates at a given groundwater condition and the other is the remarkably low sorption capacity of the laumontite for U(VI). author)

Fluorescent silver nanoclusters for ultrasensitive determination of chromium(VI) in aqueous solution

International Nuclear Information System (INIS)

Zhang, Jian Rong; Zeng, Ai Lian; Luo, Hong Qun; Li, Nian Bing

2016-01-01

Highlights: • Fluorescent Ag nanoclusters were first applied to Cr(VI) detection. • The proposed method is simple, rapid, and environmentally friendly. • The sensor shows a wide linear range, low detection limit, and good selectivity. • The system can also be used for the indirect assay of total chromium and Cr(III). • The analyses in real water samples are satisfactory. - Abstract: In this work, a simple and sensitive Cr(VI) sensor is proposed based on fluorescent polyethyleneimine-stabilized Ag nanoclusters, which allows the determination over a wide concentration range of 0.1 nM–3.0 μM and with a detection limit as low as 0.04 nΜ and a good selectivity. The quenching mechanism was discussed in terms of the absorption and fluorescence spectra, suggesting that Cr(VI) is connected to Ag nanoclusters by hydrogen bond between the oxygen atom at the vertex of tetrahedron structure of Cr(VI) and the amino nitrogen of polyethyleneimine that surrounded Ag nanoclusters and electron transfer from Ag nanoclusters to highly electron-deficient Cr(VI) results in fluorescence quenching. Despite the failure to quench the fluorescence efficiently, Cr(III) can also be measured using the proposed Ag nanoclusters by being oxidized to Cr(VI) in alkaline solution (pH ∼9) containing H 2 O 2 . Therefore, our approach could be used to detect Cr(VI), Cr(III) and the total chromium level in aqueous solution. In addition, Cr(VI) analysis in real water samples were satisfactory, indicating this method could be practically promising for chromium measurements.

Cr(VI) reduction and immobilization by novel carbonaceous modified magnetic Fe3O4/halloysite nanohybrid.

Science.gov (United States)

Tian, Xike; Wang, Weiwei; Tian, Na; Zhou, Chaoxin; Yang, Chao; Komarneni, Sridhar

2016-05-15

In this work, a novel "Dumbbell-like" magnetic Fe3O4/Halloysite nanohybrid (Fe3O4/HNTs@C) with oxygen-containing organic group grafting on the surface of natural halloysite nanotubes (HNTs) and homogeneous Fe3O4 nanospheres selectively aggregating at the tips of modified halloysite nanotubes was successfully synthesized. XRD, TEM, IR spectroscopy, XPS and VSM were used to characterize this newly halloysite nanohybrid and its formation mechanism was discussed. Cr(VI) ions adsorption experiments showed that the Fe3O4/halloysite nanohybrid exhibited higher adsorption ability with a maximum adsorption capacity of 132 mg/L at 303K, which is about 100 times higher than that of unmodified halloysite nanotubes. More importantly, with the reduction of Fe3O4 and electron-donor effect of oxygen-containing organic groups, Cr(VI) ions were easily reduced into low toxicity Cr(III) and then adsorbed onto the surface of halloysite nanohybrid. In addition, appreciable magnetization was observed due to the aggregation of magnetite nanoparticles, which make adsorbent facility separated from aqueous solutions after Cr pollution adsorption. Copyright © 2016 Elsevier B.V. All rights reserved.

Natural and man-made hexavalent chromium, Cr(VI), in groundwater near a mapped plume, Hinkley, California—study progress as of May 2017, and a summative-scale approach to estimate background Cr(VI) concentrations

Science.gov (United States)

Izbicki, John A.; Groover, Krishangi D.

2018-03-22

This report describes (1) work done between January 2015 and May 2017 as part of the U.S. Geological Survey (USGS) hexavalent chromium, Cr(VI), background study and (2) the summative-scale approach to be used to estimate the extent of anthropogenic (man-made) Cr(VI) and background Cr(VI) concentrations near the Pacific Gas and Electric Company (PG&E) natural gas compressor station in Hinkley, California. Most of the field work for the study was completed by May 2017. The summative-scale approach and calculation of Cr(VI) background were not well-defined at the time the USGS proposal for the background Cr(VI) study was prepared but have since been refined as a result of data collected as part of this study. The proposed summative scale consists of multiple items, formulated as questions to be answered at each sampled well. Questions that compose the summative scale were developed to address geologic, hydrologic, and geochemical constraints on Cr(VI) within the study area. Each question requires a binary (yes or no) answer. A score of 1 will be assigned for an answer that represents data consistent with anthropogenic Cr(VI); a score of –1 will be assigned for an answer that represents data inconsistent with anthropogenic Cr(VI). The areal extent of anthropogenic Cr(VI) estimated from the summative-scale analyses will be compared with the areal extent of anthropogenic Cr(VI) estimated on the basis of numerical groundwater flow model results, along with particle-tracking analyses. On the basis of these combined results, background Cr(VI) values will be estimated for “Mojave-type” deposits, and other deposits, in different parts of the study area outside the summative-scale mapped extent of anthropogenic Cr(VI).

Effect of Salicylic and Picolinic Acids on the Adsorption of U(VI) onto Oxides

International Nuclear Information System (INIS)

Park, Kyoung Kyun; Jung, Euo Chang; Cho, Hye Ryun; Song, Kyu Seok

2009-01-01

The effect of organic acids on the adsorption of U(VI) onto oxide surfaces (TiO 2 (anatase), SiO 2 (amorphous) and Al 2 O-3(amorphous)) has been investigated. Two different organic acids, salicylic and picolinic acids, were used. Changes of adsorption ratio of U(VI), which depend on the existence of organic acids in a sample, were measured as a function of pH. Quantities of adsorbed organic acids, which depend on the existence of U(VI) in a sample, were also measured as a function of pH. It is confirmed that the soluble complex formation of U(VI) with organic acids can deteriorate the adsorption of U(VI) onto TiO 2 surface. It is noteworthy that salicylic acid does not affect the adsorption of U(VI) onto SiO 2 surface, however, picolinic acid enhances the adsorption of U(VI) onto SiO 2 surface. The latter effect can be understood by considering the formation of a ternary surface complex on SiO 2 surface, which was confirmed by the co-adsorption of picolinic acid with U(VI) and the change in a fluorescence spectra of U(VI) on surface, In the case of Al 2 O-3, organic acids themselves were largely adsorbed onto a surface without deteriorating the adsorption of U(VI). This would support the possibility of a ternary surface complex formation on the Al 2 O-3 surface, and an additional spectroscopic study is required.

Role of paramagnetic chromium in chromium(VI)-induced damage in cultured mammalian cells.

OpenAIRE

Sugiyama, M

1994-01-01

Chromium(VI) compounds are known to be potent toxic and carcinogenic agents. Because chromium(VI) is easily taken up by cells and is subsequently reduced to chromium(III), the formation of paramagnetic chromium such as chromium(V) and chromium(III) is believed to play a role in the adverse biological effects of chromium(VI) compounds. The present report, uses electron spin resonance (ESR) spectroscopy; the importance of the role of paramagnetic chromium in chromium(VI)-induced damage in intac...

Environmental survey of Region VI, Haltenbanken, 2009; Miljoeundersoekelse i Region VI, Haltenbanken, 2009

Energy Technology Data Exchange (ETDEWEB)

Holm, May-Helen; Cochrane, Sabine; Mannvik, Hans-Petter; Wasbotten, Ingar Halvorsen

2010-07-01

There has been an environmental investigation in Region VI Halten Bank. This report presents the results of the chemical and biological assays performed on samples from a total of 316 stations in 16 fields and 15 regional stations. A status of environmental conditions in the region is given at the end of the report. (AG)

Sorption and bioreduction of hexavalent uranium at a military facility by the Chesapeake Bay

International Nuclear Information System (INIS)

Dong Wenming; Xie Guibo; Miller, Todd R.; Franklin, Mark P.; Oxenberg, Tanya Palmateer; Bouwer, Edward J.; Ball, William P.; Halden, Rolf U.

2006-01-01

Directly adjacent to the Chesapeake Bay lies the Aberdeen Proving Ground, a U.S. Army facility where testing of armor-piercing ammunitions has resulted in the deposition of >70,000 kg of depleted uranium (DU) to local soils and sediments. Results of previous environmental monitoring suggested limited mobilization in the impact area and no transport of DU into the nation's largest estuary. To determine if physical and biological reactions constitute mechanisms involved in limiting contaminant transport, the sorption and biotransformation behavior of the radionuclide was studied using geochemical modeling and laboratory microcosms (500 ppb U(VI) initially). An immediate decline in dissolved U(VI) concentrations was observed under both sterile and non-sterile conditions due to rapid association of U(VI) with natural organic matter in the sediment. Reduction of U(VI) to U(IV) occurred only in non-sterile microcosms. In the non-sterile samples, intrinsic bioreduction of uranium involved bacteria of the order Clostridiales and was only moderately enhanced by the addition of acetate (41% vs. 56% in 121 days). Overall, this study demonstrates that the migration of depleted uranium from the APG site into the Chesapeake Bay may be limited by a combination of processes that include rapid sorption of U(VI) species to natural organic matter, followed by slow, intrinsic bioreduction to U(IV). - At the Aberdeen Proving Ground in Maryland, USA, migration of depleted uranium into the Chesapeake Bay is limited by rapid sorption of the radionuclide to natural organic matter followed by slow biological reduction of water-soluble U(VI) to the insoluble and less toxic U(IV) species

Hexavalent Chromium: Analysis of the Mechanism of Groundwater Contamination in a Former Industrial Site in the Province of Vicenza (Northern Italy)

OpenAIRE

Valentina Accoto; Pierluigi Bullo; Ruben Faccio; Leonardo Mason; Andrea Sottani

2017-01-01

The study consisted in the analysis of the mobilization mechanisms of hexavalent chromium (Cr(VI)) into groundwater from a decommissioned contaminated factory. The site is located in the Province of Vicenza and formerly was a chrome-plating plant. The subsoil consists predominantly of gravelly deposits with a thickness of at least one hundred meters. An unconfined aquifer is present with water table at about 23 m depth bgl. During the seven years of monitoring (2008-2014), the fluctuation of ...

Biased Brownian motion mechanism for processivity and directionality of single-headed myosin-VI.

Science.gov (United States)

Iwaki, Mitsuhiro; Iwane, Atsuko Hikikoshi; Ikebe, Mitsuo; Yanagida, Toshio

2008-01-01

Conventional form to function as a vesicle transporter is not a 'single molecule' but a coordinated 'two molecules'. The coordinated two molecules make it complicated to reveal its mechanism. To overcome the difficulty, we adopted a single-headed myosin-VI as a model protein. Myosin-VI is an intracellular vesicle and organelle transporter that moves along actin filaments in a direction opposite to most other known myosin classes. The myosin-VI was expected to form a dimer to move processively along actin filaments with a hand-over-hand mechanism like other myosin organelle transporters. However, wild-type myosin-VI was demonstrated to be monomer and single-headed, casting doubt on its processivity. Using single molecule techniques, we show that green fluorescent protein (GFP)-fused single-headed myosin-VI does not move processively. However, when coupled to a 200 nm polystyrene bead (comparable to an intracellular vesicle in size) at a ratio of one head per bead, single-headed myosin-VI moves processively with large (40 nm) steps. Furthermore, we found that a single-headed myosin-VI-bead complex moved more processively in a high-viscous solution (40-fold higher than water) similar to cellular environment. Because diffusion of the bead is 60-fold slower than myosin-VI heads alone in water, we propose a model in which the bead acts as a diffusional anchor for the myosin-VI, enhancing the head's rebinding following detachment and supporting processive movement of the bead-monomer complex. This investigation will help us understand how molecular motors utilize Brownian motion in cells.

Molasses as an efficient low-cost carbon source for biological Cr(VI) removal

Energy Technology Data Exchange (ETDEWEB)

Michailides, Michail K. [Department of Environmental and Natural Resources Management, University of Patras, 2 G. Seferi Str., GR-30100 Agrinio (Greece); Tekerlekopoulou, Athanasia G., E-mail: atekerle@upatras.gr [Department of Environmental and Natural Resources Management, University of Patras, 2 G. Seferi Str., GR-30100 Agrinio (Greece); Akratos, Christos S.; Coles, Sandra [Department of Environmental and Natural Resources Management, University of Patras, 2 G. Seferi Str., GR-30100 Agrinio (Greece); Pavlou, Stavros [Institute of Chemical Engineering Sciences (FORTH/ICE-HT), Stadiou Str., Platani, P.O. Box 1414, GR-26504 Patras (Greece); Department of Chemical Engineering, University of Patras, GR-26504 Patras (Greece); Vayenas, Dimitrios V. [Department of Environmental and Natural Resources Management, University of Patras, 2 G. Seferi Str., GR-30100 Agrinio (Greece); Institute of Chemical Engineering Sciences (FORTH/ICE-HT), Stadiou Str., Platani, P.O. Box 1414, GR-26504 Patras (Greece)

2015-01-08

Highlights: • Suspended and attached growth reactors were examined for Cr(VI) bio-reduction. • Molasses was proved an efficient and very low cost carbon source. • Molasses was more efficient than sugar in enhancing Cr(VI) reduction. • SBR with recirculation was the most proper operating mode. - Abstract: In the present study, indigenous microorganisms from industrial sludge were used to reduce the activity of Cr(VI). Molasses, a by-product of sugar processing, was selected as the carbon source (instead of sugar used in a previous work) as it is a low-cost energy source for bioprocesses. Initially, experiments were carried out in suspended growth batch reactors for Cr(VI) concentrations of 1.5–110 mg/L. The time required for complete Cr(VI) reduction increased with initial Cr(VI) concentration. Initial molasses concentration was also found to influence the Cr(VI) reduction rate. The optimal concentration for all initial Cr(VI) concentrations tested was 0.8 gC/L. Experiments were also carried out in packed-bed reactors. Three different operating modes were used to investigate the optimal performance and efficiency of the filter, i.e. batch, continuous and SBR with recirculation. The latter mode with a recirculation rate of 0.5 L/min lead to significantly high Cr(VI) reduction rates (up to 135 g/m{sup 2} d). The results of this work were compared with those of a similar work using sugar as the carbon source and indicate that molasses could prove a feasible technological solution to a serious environmental problem.

Kinetic study of time-dependent fixation of U{sup VI} on biochar

Energy Technology Data Exchange (ETDEWEB)

Ashry, A. [Division of Agricultural and Environmental Sciences, School of Biosciences, University of Nottingham, Sutton Bonington, Leicestershire LE12 5RD (United Kingdom); Radiation Protection Department, Nuclear Research Centre, Egyptian Atomic Energy Authority, Cairo (Egypt); Bailey, E.H., E-mail: liz.bailey@nottingham.ac.uk [Division of Agricultural and Environmental Sciences, School of Biosciences, University of Nottingham, Sutton Bonington, Leicestershire LE12 5RD (United Kingdom); Chenery, S.R.N. [British Geological Survey, Nicker Hill, Keyworth, Nottingham NG12 5GG (United Kingdom); Young, S.D. [Division of Agricultural and Environmental Sciences, School of Biosciences, University of Nottingham, Sutton Bonington, Leicestershire LE12 5RD (United Kingdom)

2016-12-15

Biochar, a by-product from the production of biofuel and syngas by gasification, was tested as a material for adsorption and fixation of U{sup VI} from aqueous solutions. A batch experiment was conducted to study the factors that influence the adsorption and time-dependent fixation on biochar at 20 °C, including pH, initial concentration of U{sup VI} and contact time. Uranium (U{sup VI}) adsorption was highly dependent on pH but adsorption on biochar was high over a wide range of pH values, from 4.5 to 9.0, and adsorption strength was time-dependent over several days. The experimental data for pH > 7 were most effectively modelled using a Freundlich adsorption isotherm coupled to a reversible first order kinetic equation to describe the time-dependent fixation of U{sup VI} within the biochar structure. Desorption experiments showed that U{sup VI} was only sparingly desorbable from the biochar with time and isotopic dilution with {sup 233}U{sup VI} confirmed the low, or time-dependent, lability of adsorbed {sup 238}U{sup VI}. Below pH 7 the adsorption isotherm trend suggested precipitation, rather than true adsorption, may occur. However, across all pH values (4.5-9) measured saturation indices suggested precipitation was possible: autunite below pH 6.5 and either swartzite, liebigite or bayleyite above pH 6.5.

Raman spectrometric determination of Pu(VI) and Pu(V) in nitric acid solutions

International Nuclear Information System (INIS)

Gantner, E.; Freudenberger, M.; Steinert, D.; Ache, H.J.

1987-03-01

The determination of Pu(VI) in nitric acid solutions by spontaneous Laser Raman Spectrometry (LRS) was investigated and a calibration curve was established using U(VI) as internal standard. In addition, the concentrations of Pu(VI) and Pu(V) as a function of time were measured by this method in Pu(VI) solutions of different acidity containing H 2 O 2 as the reducing agent. In solutions which are intensely coloured by the presence of Ru(NO) complexes Pu(VI) can also be determined by LRS using a Kr + laser as excitation source. In future experiments, the study of the Pu(IV)-interaction with Ru using LRS and spectrophotometry as analytical techniques is therefore intended. (orig.) [de

28 CFR 42.405 - Public dissemination of title VI information.

Science.gov (United States)

2010-07-01

... Federally Assisted Programs § 42.405 Public dissemination of title VI information. (a) Federal agencies... 28 Judicial Administration 1 2010-07-01 2010-07-01 false Public dissemination of title VI information. 42.405 Section 42.405 Judicial Administration DEPARTMENT OF JUSTICE NONDISCRIMINATION; EQUAL...

ENDF-201: ENDF/B-VI summary documentation

International Nuclear Information System (INIS)

Rose, P.F.

1991-10-01

Responsibility for oversight of the ENDF/B Evaluated Nuclear Data file lies with the Cross Section Evaluation Working Group (CSEWG), which is comprised of representatives from various governmental and industrial laboratories in the United States. Individual evaluations are provided by scientists at several US laboratories, including significant contributions by scientists from all over the world. In addition, ENDF/B-VI includes for the first time complete evaluations for three materials that were provided from laboratories outside the US. All data are checked and reviewed by CSEWG, and the data file is maintained and issued by the National Nuclear Data Center at Brookhaven National Laboratory. The previous version of the library, ENDF/B-V, was issued in 1979, and two revisions to the data file were provided in subsequent years, the latest occurring in 1981. A total of 75 new or extensively modified neutron sublibrary evaluations are included in ENDF/B-VI, and are summarized in this document. One incident proton sublibrary is described for Fe 56 . The remaining evaluations in ENDF/B-VI have been carried over from earlier versions of ENDF, and have been updated to reflect the new formats. The release of ENDF/B-VI was carried out between January and June of 1990, with groups of materials being released on ''tapes.'' Table 1 is an index to the evaluation summaries, and includes the material identification or MAT number, the responsible laboratory, and the ''tape'' number. These evaluations have been released without restrictions on their distribution or use

ENDF-201: ENDF/B-VI summary documentation

Energy Technology Data Exchange (ETDEWEB)

Rose, P.F. (comp.)

1991-10-01

Responsibility for oversight of the ENDF/B Evaluated Nuclear Data file lies with the Cross Section Evaluation Working Group (CSEWG), which is comprised of representatives from various governmental and industrial laboratories in the United States. Individual evaluations are provided by scientists at several US laboratories, including significant contributions by scientists from all over the world. In addition, ENDF/B-VI includes for the first time complete evaluations for three materials that were provided from laboratories outside the US. All data are checked and reviewed by CSEWG, and the data file is maintained and issued by the National Nuclear Data Center at Brookhaven National Laboratory. The previous version of the library, ENDF/B-V, was issued in 1979, and two revisions to the data file were provided in subsequent years, the latest occurring in 1981. A total of 75 new or extensively modified neutron sublibrary evaluations are included in ENDF/B-VI, and are summarized in this document. One incident proton sublibrary is described for Fe{sup 56}. The remaining evaluations in ENDF/B-VI have been carried over from earlier versions of ENDF, and have been updated to reflect the new formats. The release of ENDF/B-VI was carried out between January and June of 1990, with groups of materials being released on tapes.'' Table 1 is an index to the evaluation summaries, and includes the material identification or MAT number, the responsible laboratory, and the tape'' number. These evaluations have been released without restrictions on their distribution or use.

ENDF-201: ENDF/B-VI summary documentation

Energy Technology Data Exchange (ETDEWEB)

Rose, P.F. [comp.

1991-10-01

Responsibility for oversight of the ENDF/B Evaluated Nuclear Data file lies with the Cross Section Evaluation Working Group (CSEWG), which is comprised of representatives from various governmental and industrial laboratories in the United States. Individual evaluations are provided by scientists at several US laboratories, including significant contributions by scientists from all over the world. In addition, ENDF/B-VI includes for the first time complete evaluations for three materials that were provided from laboratories outside the US. All data are checked and reviewed by CSEWG, and the data file is maintained and issued by the National Nuclear Data Center at Brookhaven National Laboratory. The previous version of the library, ENDF/B-V, was issued in 1979, and two revisions to the data file were provided in subsequent years, the latest occurring in 1981. A total of 75 new or extensively modified neutron sublibrary evaluations are included in ENDF/B-VI, and are summarized in this document. One incident proton sublibrary is described for Fe{sup 56}. The remaining evaluations in ENDF/B-VI have been carried over from earlier versions of ENDF, and have been updated to reflect the new formats. The release of ENDF/B-VI was carried out between January and June of 1990, with groups of materials being released on ``tapes.`` Table 1 is an index to the evaluation summaries, and includes the material identification or MAT number, the responsible laboratory, and the ``tape`` number. These evaluations have been released without restrictions on their distribution or use.

Biological Cr(VI) removal using bio-filters and constructed wetlands.

Science.gov (United States)

Michailides, Michail K; Sultana, Mar-Yam; Tekerlekopoulou, Athanasia G; Akratos, Christos S; Vayenas, Dimitrios V

2013-01-01

The bioreduction of hexavalent chromium from aqueous solution was carried out using suspended growth and packed-bed reactors under a draw-fill operating mode, and horizontal subsurface constructed wetlands. Reactors were inoculated with industrial sludge from the Hellenic Aerospace Industry using sugar as substrate. In the suspended growth reactors, the maximum Cr(VI) reduction rate (about 2 mg/L h) was achieved for an initial concentration of 12.85 mg/L, while in the attached growth reactors, a similar reduction rate was achieved even with high initial concentrations (109 mg/L), thus confirming the advantage of these systems. Two horizontal subsurface constructed wetlands (CWs) pilot-scale units were also built and operated. The units contained fine gravel. One unit was planted with common reeds and one was kept unplanted. The mean influent concentrations of Cr(VI) were 5.61 and 5.47 mg/L for the planted and unplanted units, respectively. The performance of the planted CW units was very effective as mean Cr(VI) removal efficiency was 85% and efficiency maximum reached 100%. On the contrary, the unplanted CW achieved very low Cr(VI) removal with a mean value of 26%. Both attached growth reactors and CWs proved efficient and viable means for Cr(VI) reduction.

Modeling of the YALINA booster facility by the Monte Carlo code MONK

International Nuclear Information System (INIS)

Talamo, A.; Gohar, Y.; Kondev, F.; Kiyavitskaya, H.; Serafimovich, I.; Bournos, V.; Fokov, Y.; Routkovskaya, C.

2007-01-01

The YALINA-Booster facility has been modeled according to the benchmark specifications defined for the IAEA activity without any geometrical homogenization using the Monte Carlo codes MONK and MCNP/MCNPX/MCB. The MONK model perfectly matches the MCNP one. The computational analyses have been extended through the MCB code, which is an extension of the MCNP code with burnup capability because of its additional feature for analyzing source driven multiplying assemblies. The main neutronics arameters of the YALINA-Booster facility were calculated using these computer codes with different nuclear data libraries based on ENDF/B-VI-0, -6, JEF-2.2, and JEF-3.1.

Chrome Tanning Leather of Giant Sea Perch Combined with Seed Extract Areca Nut on the Physical Characteristics

Directory of Open Access Journals (Sweden)

Bustami - Ibrahim

2014-11-01

Full Text Available Tanning is the process of converting raw hide protein to leather, which are stable, not easily decompose, and is suitable for a variety of uses. The use of vegetable based tanning materials in the leather tanning process has not been carried out. Vegetable based materials that were used are betel nuts. This plant contains tannin which is the main agent in the process of leather tanning. The aim of this study was to determine the physical characteristics of snapper leather treated with betel nut extract. Soxhlet extracting method with methanol as a solvent were used to obtain tannin from betel nuts. Tanned Snapper Leather were analyzed for physical quality, elongation strength, tensile strength, tear strength, and sewing strength. The result showed that methanol extracted betel nut with 10% concentration gives the optimum physical characteristics.Keywords: areca nut, chrome, snapper, snapper

VI Tallinna arhitektuuritriennaal / Leonhard Lapin

Index Scriptorium Estoniae

Lapin, Leonhard, 1947-

2005-01-01

15.-17. IX Tallinnas Niguliste kirikus toimuval VI Tallinna arhitektuuritriennaalil esinevad inglise arhitektuurikriitik Peter Davey, šveitsi arhitekt Peter Zumthor, soome arhitekt Juha Leviskä, eesti arhitekt Vilen Künnapu, eesti kunstiajaloolane Juhan Maiste jt. Külastatakse KUMU, tutvutab autor Pekka Vapaavuori

Extraction of uranium (VI) sulphate complexes by Adogen amines

Energy Technology Data Exchange (ETDEWEB)

Elyamani, I S; Abd Elmessieh, E N [Nuclear chemistry department, hot laboratories center, atomic energy authority, Cairo, (Egypt)

1995-10-01

The distribution of U(VI) between aqueous H{sub 2} So{sub 4} solutions and organic phases of adogen-368 has been described. The dependence of extraction on acidity, diluent type, metal and extractant concentrations was investigated. The possible extraction mechanism is discussed in the light of results obtained. The separation of U(VI) from rare earths is suggested. 5 figs., 1 tab.

Photo-oxidation. Of the system chrome hexavalent-4-chlorophenol

International Nuclear Information System (INIS)

Gil Pavas, Edison; Cabrera Limpias, Marianela; Jaramillo Jimenez, Sergio Alejandro

2003-01-01

As a proposal to eliminate highly toxic chemical components derived from industrial waste, the researchers study the behavior of the compound hexavalent chromium / 4-chlorophenol system when subjected to photo degradation in a photo-reactor compound parabolic cylinder (CPC) to scale pilot. The effect is analyzed in order to determine the operation conditions to reach the highest degradation levels possible. The analyzed variables were pH, concentration of catalyst (TiO 2 ), time of recirculation and the relation of initial concentrations among polluting agents. The factor that most influences the levels of removal reached is the pH, which has a different effect for each of the pollutants. This implies that, theoretically, you cannot adopt a unique group of operation parameters to favor the degradation of both however, in the practice; high levels of degradation of both pollutants are obtained in the optimal point of operation of the chrome. It is also observed that the catalyst concentration does not influence the degradation of the polluting agents significantly, at least for the initial concentrations studied. The recirculation time is closely related to the kinetics of degradation of each polluting agent. Elevated degradation levels are reached in a short time for 4-chlorophenol, while more prolonged recirculation times are required for hexavalent chromium. The relation of initial concentrations of the polluting agents also exerts an opposite effect on the degradation levels reached for each polluting agent; the hexavalent chromium reduction is favored with high initial concentrations of 4-chlorophenol, whereas the oxidation of 4-chlorophenol is favored with high initial hexavalent chromium concentrations, which suggests some synergy between the oxidation-reduction reactions of 4-chlorophenol and hexavalent chromium. Finally, a 97% hexavalent chromium reduction and a 94.9% oxidation of 4-chlorophenol were obtained

Chromed Leather Dyeing Peculiarities when Deliming with Peracetic Acid

Directory of Open Access Journals (Sweden)

Kęstutis BELEŠKA

2013-05-01

Full Text Available The research was aimed to investigate the influence of deliming with peracetic acid on leather dyeing kinetics. Hydrophobic C.I. Acid Red 213 and hydrophilic C.I. Acid Red 423 dyes were used. Sorption of dye depends on hydrophobicity/hydrophility of dye and dyeing temperature. Equilibrium of process is reached faster using hydrophobic C.I. Acid Red 213 at 45 ºC. However, both control and experimental leather fibres adsorb more hydrophilic dye C.I. Acid Red 423 and this fact does not depend on temperature. The diffusion coefficient of dye C.I. Acid Red 423 calculated according to Weisz model is higher when dyeing conventional leather. The change of deliming method has influence on chromed leather dyeing but this influence is not significant. The adsorption ability of control leather fibres at 30 ºC and 45 ºC is higher using both dyes as compared to the dyeing the experimental one. The increase of dyeing temperature increases the adsorption ability independently on the sort of leather fibres. Such dependence of the adsorption ability on the temperature shows that hydrophobic action and van der Waals forces prevail between dye and fibres during dyeing process. The Gibbs energy changes show that adsorption of both dyes by leather fibres independently on their sort is a spontaneous process. The affinity of both dyes to conventional leather fibres is higher comparing with experimental one. The change of enthalpy is positive in all cases, and it means that the driving force of the dyeing is the change of entropy.DOI: http://dx.doi.org/10.5755/j01.ms.19.2.4431

Reduction of chromium (VI by the indirect action of Thiobacillus thioparus

Directory of Open Access Journals (Sweden)

E. Donati

2003-03-01

Full Text Available The microbial reduction of chromium(VI to chromium(III has been one of the most widely studied forms of metal bioremediation. Recently, we have found that Thiobacillus ferrooxidans and Thiobacillus thiooxidans, growing on elemental sulphur, can indirectly promote chromium(VI reduction by producing reducing agents such as sulphite and thiosulphate, which abiotically reduce chromium(VI. Those species of Thiobacillus are acidophilic bacteria which grow optimally at pH values lower than 4. However, most of those reducing agents are stabilised at higher pH values. Thus, the present paper reports on the ability to reduce chromium(VI using another specie of Thiobacilli, Thiobacillus thioparus, which is able to grow at pH close to 7.0. T. thioparus cultures were carried out in a fermentation vessel containing medium and sulphur as the sole energy source and maintained at 30ºC and 400 rpm. The pH was adjusted to 6.0, 7.0 or 8.0 and maintained with the automatic addition of KOH. Our results show high chromium (VI reduction values (close to 100% at the end of bacterial growth at the three pH values. The results of these experiments are very promising for development of a microbiological process to be used in the detoxification of chromium(VI-polluted effluents.

CHROMIUM(VI REDUCTION BY A MIXED CULTURE OF SULFATE REDUCING BACTERIA DEVELOPED IN COLUMN REACTOR

Directory of Open Access Journals (Sweden)

Cynthia Henny

2008-03-01

Full Text Available A lactate enriched mixed sulfate reducing bacteria (SRB culture was examined for the reduction of Cr(VI in a continuous flow system. The influent was mineral salts media added with lactate and sulfate with amounts of 8 and 6 mM respectively as electron donor and electron acceptor. The SRB culture was allowed to stabilize in the column before adding the Cr(VI to the influent. Chromium and sulfate reduction and lactate oxidation were examined by measuring the concentrations of Cr(Vl, sulfate and lactate in the influent and the effluent over time. The experiment was discontinued when Cr(VI concentration in the effiuent was breakthrough. In the absence of Cr(VI, sulfate was not completely reduced in the column, although lactate was completely oxidized and acetate as an intermediate product was not often detected. Almost all of Cr(VI loaded was reduced in the column seeded with the SRB culture at influent Cr(VI concentrations of 192,385 and769 mM. There was no significant Cr(VI loss in the control column, indicating that Cr(VI removal was due to the reduction of Cr(VI to Cr (lll by the SRB culture. The instantaneous Cr(VI removal decreased to a minimum of 32%, 24 days after the influent Cr(VI concentration was increased to 1540 mM, ancl sulfate removal efficiency decreased to a minimum of 17%. The SRB population in the column decreased 100 days after C(VI was added to the column. The total mass of Cr(VI reduced was approximately 878 mmol out of 881 mmol of Cr(Vl loaded in 116 days. The results clearly show that our developed SRB culture could reduced Cr(Vl considerably.

Studies on the kinetics of uranium (VI) electro-reduction and reextraction: Pt. 2

International Nuclear Information System (INIS)

Tong Jihong; Ma Xuquan; Tai Derong; Sun Shiren

1992-01-01

The kinetics of U(VI) reextraction and U(IV) extraction in the process of U(VI) electro-reduction with the system of HNO 3 -N 2 H 5 NO 3 (H 2 O)/UO 2 (NO 3 ) 2 -HNO 3 (30% TBP-OK) is investigated with a constant interfacial area cell (Lewis cell) with cathode and anode in it. According to the experimental results and data processing, the apparent activation energy of the U(VI) reextraction process is 36.02 kJ/nol. The U(VI) reextraction rate increases when the stirring speed of two phases increases. This process is mainly diffusion controlled. For the U(VI) extraction process, the apparent activation energy is 21.13 kJ/mol. The U(IV) extraction rate also increases when the stirring speed of two phases increases. This process is mainly diffusion controlled. The lower the potential of cathode is, the higher the rates of U(VI) reextraction and U(IV) extraction are

Effects of chromium on the immune system.

Science.gov (United States)

Shrivastava, Richa; Upreti, R K; Seth, P K; Chaturvedi, U C

2002-09-06

Chromium is a naturally occurring heavy metal found commonly in the environment in trivalent, Cr(III), and hexavalent, Cr(VI), forms. Cr(VI) compounds have been declared as a potent occupational carcinogen among workers in chrome plating, stainless steel, and pigment industries. The reduction of Cr(VI) to Cr(III) results in the formation of reactive intermediates that together with oxidative stress oxidative tissue damage and a cascade of cellular events including modulation of apoptosis regulatory gene p53, contribute to the cytotoxicity, genotoxicity and carcinogenicity of Cr(VI)-containing compounds. On the other hand, chromium is an essential nutrient required to promote the action of insulin in body tissues so that the body can use sugars, proteins and fats. Chromium is of significant importance in altering the immune response by immunostimulatory or immunosuppressive processes as shown by its effects on T and B lymphocytes, macrophages, cytokine production and the immune response that may induce hypersensitivity reactions. This review gives an overview of the effects of chromium on the immune system of the body. Copyright 2002 Federation of European Microbiological Societies

Long-time rupture strength and creep behaviour of welded joints on heat-resistant CrMoV steels with 1 and 12% chrome

International Nuclear Information System (INIS)

Maier, G.; Maile, K.; Theofel, H.

1985-01-01

Power plant components in the creep range are damaged frequently in the weld joint zones. The investigation concentrated therefore on the reliability of the information supplied by tests on small- and large-size samples. Creep rupture tests of dissimilar welded joints (1% with 12% chrome) with variations of heat input and weld metal have been conducted. At creep rupture times of about 10 4 h all joints failed in the outside heat affected zone of the weaker base metal. Large-size samples, proved in comparison at same stresses, showed distinctly longer times to rupture. (orig.) [de

Kinetics and Products of Chromium(VI) Reduction by Iron(II/III)-Bearing Clay Minerals.

Science.gov (United States)

Joe-Wong, Claresta; Brown, Gordon E; Maher, Kate

2017-09-05

Hexavalent chromium is a water-soluble pollutant, the mobility of which can be controlled by reduction of Cr(VI) to less soluble, environmentally benign Cr(III). Iron(II/III)-bearing clay minerals are widespread potential reductants of Cr(VI), but the kinetics and pathways of Cr(VI) reduction by such clay minerals are poorly understood. We reacted aqueous Cr(VI) with two abiotically reduced clay minerals: an Fe-poor montmorillonite and an Fe-rich nontronite. The effects of ionic strength, pH, total Fe content, and the fraction of reduced structural Fe(II) [Fe(II)/Fe(total)] were examined. The last variable had the largest effect on Cr(VI) reduction kinetics: for both clay minerals, the rate constant of Cr(VI) reduction varies by more than 3 orders of magnitude with Fe(II)/Fe(total) and is described by a linear free energy relationship. Under all conditions examined, Cr and Fe K-edge X-ray absorption near-edge structure spectra show that the main Cr-bearing product is a Cr(III)-hydroxide and that Fe remains in the clay structure after reacting with Cr(VI). This study helps to quantify our understanding of the kinetics of Cr(VI) reduction by Fe(II/III)-bearing clay minerals and may improve predictions of Cr(VI) behavior in subsurface environments.

Polyaniline (PANI) modified bentonite by plasma technique for U(VI) removal from aqueous solution

Energy Technology Data Exchange (ETDEWEB)

Liu, Xinghao [Institute of Nuclear Physics and Chemistry, China Academy of Engineering Physics, Mianyang 621900 (China); Intelligent Manufacturing Technology Research Institute, Hefei University of Technology, Hefei 230088 (China); Cheng, Cheng [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei 230031 (China); Xiao, Chengjian, E-mail: xiaocj@caep.cn [Institute of Nuclear Physics and Chemistry, China Academy of Engineering Physics, Mianyang 621900 (China); Shao, Dadong, E-mail: shaodadong@126.com [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei 230031 (China); Xu, Zimu, E-mail: xzm@mail.ustc.edu.cn [Intelligent Manufacturing Technology Research Institute, Hefei University of Technology, Hefei 230088 (China); Wang, Jiaquan; Hu, Shuheng [Intelligent Manufacturing Technology Research Institute, Hefei University of Technology, Hefei 230088 (China); Li, Xiaolong; Wang, Weijuan [Institute of Nuclear Physics and Chemistry, China Academy of Engineering Physics, Mianyang 621900 (China)

2017-07-31

Highlights: • PANI/bentonie can be synthesized by simple plasma technique. • PANI/bentonie has an excellent adsorption capacity for trace uranium in solution. • U(VI) adsorption on PANI/bentonite is a spontaneous and endothermic process. - Abstract: Polyaniline (PANI) modified bentonite (PANI/bentonie) was synthesized by plasma induced polymerization of aniline on bentonite surface, and applied to uptake of uranium(VI) ions from aqueous solution. The as-synthesized PANI/bentonie was characterized by scanning electron microscopy (SEM), powder X-ray diffraction (XRD), thermal gravimetric analysis (TGA), and X-ray photoelectron spectroscopy (XPS). Batch adsorption technique was utilized to investigate the adsorption of U(VI) on bentonite and PANI/bentonite. The adsorption of U(VI) (10 mg/L) on PANI/bentonite surface is fairly depend on solution pH, ionic strength, and temperature in solution. The modified PANI on PANI/bentonite surface significantly enhances its adsorption capability for U(VI). The presence of humic acid (HA) can sound enhance U(VI) adsorption on PANI/bentonite at pH < 6.5 because of the strong complexation, and inhibits U(VI) adsorption at pH > 6.5. According to the thermodynamic parameters, the adsorption of U(VI) on PANI/bentonite surface is a spontaneous and endothermic process. The results highlight the application of PANI/bentonite composites as candidate material for the uptake of trace U(VI) from aqueous solution.

Study on Cr(VI) Leaching from Cement and Cement Composites

Science.gov (United States)

Palascakova, Lenka; Kanuchova, Maria

2018-01-01

This paper reports an experimental study on hexavalent chromium leaching from cement samples and cement composites containing silica fume and zeolite additions that were subjected to various leaching agents. The water-soluble Cr(VI) concentrations in cements ranged from 0.2 to 3.2 mg/kg and represented only 1.8% of the total chromium content. The presence of chromium compounds with both chromium oxidation states of III and VI was detected in the cement samples by X-ray photoelectron spectroscopy (XPS). Leaching tests were performed in a Britton-Robinson buffer to simulate natural conditions and showed increased dissolution of Cr(VI) up to 6 mg/kg. The highest amount of leached hexavalent chromium was detected after leaching in HCl. The findings revealed that the leaching of chromium from cements was higher by 55–80% than that from the cement composites. A minimum concentration was observed for all cement samples when studying the relationship between the soluble Cr(VI) and the cement storage time. PMID:29690550

Remediation of U(VI)-contaminated water using zero-valent iron

International Nuclear Information System (INIS)

Abdelouas, A.; Gong, W.; Lutze, W.; Nuttall, E.

1999-01-01

We investigated the possibility of U(VI) reduction by zero-valent iron (Fe 0 ). We conducted batch experiments with granular iron and solutions containing 0.25 and 9.3 mg L -1 U(VI) at 24 deg C. The solution pH ranges between 2 and 9. In all experiments uranium removal was complete within several hours to several days regardless of the pH value. The reduced uranium precipitated as poorly crystallized hydrated uraninite, UO 2 .nH 2 O. The reduction of U(VI) to U(IV) by Fe 0 was found to be the principal mechanism of U removal from the solution. Other mechanisms such as U(VI) sorption on the newly formed Fe(III) hydroxides are insignificant. These results show that zero-valent iron can be used to remedy U-contaminated waters from uranium mines and mill tailings sites, the pH of which usually ranges between 2 and 9. (authors)

A critical review of ferrate(VI)-based remediation of soil and groundwater.

Science.gov (United States)

Rai, Prabhat Kumar; Lee, Jechan; Kailasa, Suresh Kumar; Kwon, Eilhann E; Tsang, Yiu Fai; Ok, Yong Sik; Kim, Ki-Hyun

2018-01-01

Over the past few decades, diverse chemicals and materials such as mono- and bimetallic nanoparticles, metal oxides, and zeolites have been used for soil and groundwater remediation. Ferrate (Fe VI O 4 2- ) has been widely employed due to its high-valent iron (VI) oxo compound with high oxidation/reduction potentials. Ferrate has received attention for wide environmental applications including water purification and sewage sludge treatment. Ferrate provides great potential for diverse environmental applications without any environmental problems. Therefore, this paper provides comprehensive information on the recent progress on the use of (Fe VI O 4 2- ) as a green material for use in sustainable treatment processes, especially for soil and water remediation. We reviewed diverse synthesis recipes for ferrates (Fe VI O 4 2- ) and their associated physicochemical properties as oxidants, coagulants, and disinfectants for the elimination of a diverse range of chemical and biological species from water/wastewater samples. A summary of the eco-sustainable performance of ferrate(VI) in water remediation is also provided and the future of ferrate(VI) is discussed in this review. Copyright © 2017 Elsevier Inc. All rights reserved.

Carbon-13 NMR characterization of actinyl(VI) carbonate complexes in aqueous solution

International Nuclear Information System (INIS)

Clark, D.L.; Hobart, D.E.; Palmer, P.D.; Sullivan, J.C.; Stout, B.E.

1992-01-01

The uranyl(VI) carbonate system has been re-examined using 13 C NMR of 99.9% 13 C-enriched U VI O 2 ( 13 CO 3 ) 3 4- in millimolar concentrations. By careful control of carbonate ion concentration, we have confirmed the existence of the trimer, and observed dynamic equilibrium between the monomer and the timer. In addition, the ligand exchange reaction between free and coordinated carbonate on Pu VI O 2 ( 13 CO 3 ) 3 4- and Am VI O 2 ( 13 CO 3 ) 3 4- systems has been examined by variable temperature 13 C NMR line-broadening techniques 13 C NMR line-broadening techniques. A modified Carr-Purcell-Meiboom-Gill NMR pulse sequence was written to allow for experimental determination of ligand exchange parameters for paramagnetic actinide complexes. Preliminary Eyring analysis has provided activation parameters of ΔG double-dagger 295 = 56 kJ/M, ΔH double-dagger = 38 kJ/M, and ΔS double-dagger = -60 J/M-K for the plutonyl triscarbonate system, suggesting an associative transition state for the plutonyl (VI) carbonate complex self-exchange reaction. Experiments for determination of the activation parameters for the americium (VI) carbonate system are in progress

Oral-facial-digital syndrome with mesoaxial polysyndactyly, common AV canal, hirschsprung disease and sacral dysgenesis: Probably a transitional type between II, VI, variant of type VI or a new type

Directory of Open Access Journals (Sweden)

Rabah M. Shawky

2014-07-01

Full Text Available We report a 4 month old male infant, the first in order of birth of healthy first cousin consanguineous parents who has many typical features of oral-facial-digital syndrome type VI (OFDS VI including hypertelorism, bilateral convergent squint, depressed nasal bridge, and wide upturned nares, low set posteriorly rotated ears, long philtrum, gum hyperplasia with notches of the alveolar borders, high arched palate, and hyperplastic oral frenula. He has mesoaxial and postaxial, polysyndactyly which is the specific feature of OFDS VI, however the cerebellum is normal on MRI brain. He has also some rare congenital anomalies including common atrioventricular canal, hirschsprung disease, and sacral dysgenesis. This patient may have a transitional type between II and VI, a variant of type VI or a new type.

Hvad skal vi med Trump-satire?

DEFF Research Database (Denmark)

Møller, Mette

2017-01-01

Trump-satire er et stort hit, og særligt en lang række satiriske videohilsner til Trump fra lande verden over får folk til at trække på smilebåndet. Men hvorfor er det så sjovt at gøre grin med Trump, og hvad kan vi bruge den politiske humor til?......Trump-satire er et stort hit, og særligt en lang række satiriske videohilsner til Trump fra lande verden over får folk til at trække på smilebåndet. Men hvorfor er det så sjovt at gøre grin med Trump, og hvad kan vi bruge den politiske humor til?...

KENO-VI: A Monte Carlo Criticality Program with generalized quadratic geometry

International Nuclear Information System (INIS)

Hollenbach, D.F.; Petrie, L.M.; Landers, N.F.

1993-01-01

This report discusses KENO-VI which is a new version of the KENO monte Carlo Criticality Safety developed at Oak Ridge National Laboratory. The purpose of KENO-VI is to provide a criticality safety code similar to KENO-V.a that possesses a more general and flexible geometry package. KENO-VI constructs and processes geometry data as sets of quadratic equations. A lengthy set of simple, easy-to-use geometric functions, similar to those provided in KENO-V.a., and the ability to build more complex geometric shapes represented by sets of quadratic equations are the heart of the geometry package in KENO-VI. The code's flexibility is increased by allowing intersecting geometry regions, hexagonal as well as cuboidal arrays, and the ability to specify an array boundary that intersects the array

Chemistry of the Colloidal Group II-VI Nanocrystal Synthesis

Energy Technology Data Exchange (ETDEWEB)

Liu, Haitao [Univ. of California, Berkeley, CA (United States)

2007-05-17

In the last two decades, the field of nanoscience andnanotechnology has witnessed tremendous advancement in the synthesis andapplication of group II-VI colloidal nanocrystals. The synthesis based onhigh temperature decomposition of organometallic precursors has becomeone of the most successful methods of making group II-VI colloidalnanocrystals. This methodis first demonstrated by Bawendi and coworkersin 1993 to prepare cadmium chalcogenide colloidal quantum dots and laterextended by others to prepare other group II-VI quantum dots as well asanisotropic shaped colloidal nanocrystals, such as nanorod and tetrapod.This dissertation focuses on the chemistry of this type of nanocrystalsynthesis. The synthesis of group II-VI nanocrystals was studied bycharacterizing the molecular structures of the precursors and productsand following their time evolution in the synthesis. Based on theseresults, a mechanism was proposed to account for the 2 reaction betweenthe precursors that presumably produces monomer for the growth ofnanocrystals. Theoretical study based on density functional theorycalculations revealed the detailed free energy landscape of the precursordecomposition and monomerformation pathway. Based on the proposedreaction mechanism, a new synthetic method was designed that uses wateras a novel reagent to control the diameter and the aspect ratio of CdSeand CdS nanorods.

Kinetics of U(VI) reduction by a dissimilatory Fe(III)-reducing bacterium under non-growth conditions

International Nuclear Information System (INIS)

Truex, M.J.; Peyton, B.M.; Valentine, N.B.; Gorby, Y.A.

1997-01-01

Dissimilatory metal-reducing microorganisms may be useful in processes designed for selective removal of uranium from aqueous streams. These bacteria can use U(VI) as an electron acceptor and thereby reduce soluble U(VI) to insoluble U(IV). While significant research has been devoted to demonstrating and describing the mechanism of dissimilatory metal reduction, the reaction kinetics necessary to apply this for remediation processes have not been adequately defined. In this study, pure culture Shewanella alga strain BrY reduced U(VI) under non-growth conditions in the presence of excess lactate as the electron donor. Initial U(VI) concentrations ranged from 13 to 1,680microM. A maximum specific U(VI) reduction rate of 2.37 micromole-U(VI)/(mg-biomass h) and Monod half-saturation coefficient of 132 microM-U(VI) were calculated from measured U(VI) reduction rates. U(VI) reduction activity was sustained at 60% of this rate for at least 80 h. The initial presence of oxygen at a concentration equal to atmospheric saturation at 22 C delays but does not prevent U(VI) reduction. The rate of U(VI) reduction by BrY is comparable or better than rates reported for other metal reducing species. BrY reduces U(VI) at a rate that is 30% of its Fe(III) reduction rate

Towards a consistent geochemical model for prediction of uranium(VI) removal from groundwater by ferrihydrite

International Nuclear Information System (INIS)

Gustafsson, Jon Petter; Daessman, Ellinor; Baeckstroem, Mattias

2009-01-01

Uranium(VI), which is often elevated in granitoidic groundwaters, is known to adsorb strongly to Fe (hydr)oxides under certain conditions. This process can be used in water treatment to remove U(VI). To develop a consistent geochemical model for U(VI) adsorption to ferrihydrite, batch experiments were performed and previous data sets reviewed to optimize a set of surface complexation constants using the 3-plane CD-MUSIC model. To consider the effect of dissolved organic matter (DOM) on U(VI) speciation, new parameters for the Stockholm Humic Model (SHM) were optimized using previously published data. The model, which was constrained from available X-ray absorption fine structure (EXAFS) spectroscopy evidence, fitted the data well when the surface sites were divided into low- and high-affinity binding sites. Application of the model concept to other published data sets revealed differences in the reactivity of different ferrihydrites towards U(VI). Use of the optimized SHM parameters for U(VI)-DOM complexation showed that this process is important for U(VI) speciation at low pH. However in neutral to alkaline waters with substantial carbonate present, Ca-U-CO 3 complexes predominate. The calibrated geochemical model was used to simulate U(VI) adsorption to ferrihydrite for a hypothetical groundwater in the presence of several competitive ions. The results showed that U(VI) adsorption was strong between pH 5 and 8. Also near the calcite saturation limit, where U(VI) adsorption was weakest according to the model, the adsorption percentage was predicted to be >80%. Hence U(VI) adsorption to ferrihydrite-containing sorbents may be used as a method to bring down U(VI) concentrations to acceptable levels in groundwater

Predicting chromium (VI) adsorption rate in the treatment of liquid ...

African Journals Online (AJOL)

Administrator

The adsorption rate of chromium (VI) on commercial activated carbon during the ... time and initial chromium (VI) ion concentration. .... model, the separation factor r, according to Calvo et al (2001) cited .... Lead (II) and nickel (II) adsorption kinetics .... heavy metal by Talaromyces helicus: a trained fungus for copper and.

Cloning and expression of a Vi mimotope of Salmonella enterica ...

African Journals Online (AJOL)

STORAGESEVER

2009-09-15

Sep 15, 2009 ... A recombinant His-Vi protein of Salmonella enterica serovar Typhi was successfully constructed and cloned into ... mainly through consumption of food or water contami- nated with .... and healthy individuals (double arrows) followed by the detection using recombinant His-Vi protein as the primary antibody ...

Uranium(VI) sorption on iron oxides in Hanford Site sediment: Application of a surface complexation model

International Nuclear Information System (INIS)

Um, Wooyong; Serne, R. Jeffrey; Brown, Christopher F.; Rod, Kenton A.

2008-01-01

Sorption of U(VI) on Hanford fine sand (HFS) with varying Fe-oxide (especially ferrihydrite) contents showed that U(VI) sorption increased with the incremental addition of synthetic ferrihydrite into HFS, consistent with ferrihydrite being one of the most reactive U(VI) sorbents present in natural sediments. Surface complexation model (SCM) calculations for U(VI) sorption, using only U(VI) surface-reaction constants obtained from U(VI) sorption data on freshly synthesized ferrihydrite at different pHs, were similar to the measured U(VI) sorption results on pure synthetic ferrihydrite and on HFS with high contents of ferrihydrite (5 wt%) added. However, the SCM prediction using only U(VI) sorption reactions and constants for synthetic ferrihydrite overestimated U(VI) sorption on the natural HFS or HFS with addition of low amounts of added ferrihydrite (1 wt% added). Over-predicted U(VI) sorption was attributed to reduced reactivity of natural ferrihydrite present in Hanford Site sediments, compared to freshly prepared synthetic ferrihydrite. Even though the SCM general composite (GC) approach is considered to be a semi-quantitative estimation technique for contaminant sorption, which requires systematic experimental data on the sorbent-sorbate system being studied to obtain credible SCM parameters, the general composite SCM model was still found to be a useful technique for describing U(VI) sorption on natural sediments. Based on U(VI) batch sorption results, two simple U(VI) monodentate surface species, SO U O 2 HCO 3 and SO U O 2 OH on ferrihydrite and phyllosillicate in HFS, respectively, can be successfully used to describe U(VI) sorption onto Hanford Site sediment contacting varying geochemical solutions

Ferrate(VI) as a greener oxidant: Electrochemical generation and treatment of phenol.

Science.gov (United States)

Sun, Xuhui; Zhang, Qi; Liang, He; Ying, Li; Xiangxu, Meng; Sharma, Virender K

2016-12-05

Ferrate(VI) (Fe(VI)O4(2-), Fe(VI)) is a greener oxidant in the treatment of drinking water and wastewater. The electrochemical synthesis of Fe(VI) may be considered environmentally friendly because it involves one-step process to convert Fe(0) to Fe(VI) without using harmful chemicals. Electrolysis was performed by using a sponge iron as an anode in NaOH solution at different ionic strengths. The cyclic voltammetric (CV) curves showed that the sponge iron had higher electrical activity than the grey cast iron. The optimum current density was 0.054mAcm(-2) in 10M NaOH solution, which is much lower than the electrolyte concentrations used in other electrode materials. A comparison of current efficiency and energy consumption was conducted and is briefly discussed. The generated ferrate solution was applied to degrade phenol in water at two levels (2mgL(-1) and 5mgL(-1)). The maximum removal efficiency was ∼70% and the optimum pH for phenol treatment was 9.0. Experiments on phenol removal using conventional coagulants (ferric chloride (FeCl3) and polyaluminium chloride (PAC)) were performed independently to demonstrate that removal of phenol by Fe(VI) occurred mainly by oxidative transformation. A combination of Fe(VI) and coagulant may be advantageous in enhancing removal efficiency, adjusting pH, and facilitating flocculation. Copyright © 2015 Elsevier B.V. All rights reserved.

The O VI Mystery: Mismatch between X-Ray and UV Column Densities

Science.gov (United States)

Mathur, S.; Nicastro, F.; Gupta, A.; Krongold, Y.; McLaughlin, B. M.; Brickhouse, N.; Pradhan, A.

2017-12-01

The UV spectra of Galactic and extragalactic sightlines often show O VI absorption lines at a range of redshifts, and from a variety of sources from the Galactic circumgalactic medium to active galactic nuclei (AGN) outflows. Inner shell O VI absorption is also observed in X-ray spectra (at λ =22.03 Å), but the column density inferred from the X-ray line was consistently larger than that from the UV line. Here we present a solution to this discrepancy for the z = 0 systems. The O II Kβ line {}4{S}0\\to {(}3D)3{p}4P at 562.40 eV (≡22.04 Å) is blended with the O VI Kα line in X-ray spectra. We estimate the strength of this O II line in two different ways, and show that in most cases the O II line accounts for the entire blended line. The small amount of O VI equivalent width present in some cases has column density entirely consistent with the UV value. This solution to the O VI discrepancy, however, does not apply to high column-density systems like AGN outflows. We discuss other possible causes to explain their UV/X-ray mismatch. The O VI and O II lines will be resolved by gratings on board the proposed mission Arcus and the concept mission Lynx, and would allow the detection of weak O VI lines not just at z = 0, but also at higher redshift.

Sediment studies of the biological factors controlling the reduction of U(VI)

International Nuclear Information System (INIS)

Lovley, Derek R.

2004-01-01

Studies were conducted primarily with sediments, both in laboratory incubations and in a field experiment, with supporting studies with pure cultures. To our knowledge the sediment studies were the first on microbial U(VI) reduction in actual uranium-contaminated subsurface sediments, under conditions that mimic those found in situ. Important findings included: (1) U(VI) reduction is a biotic process in subsurface sediments. (2) U(VI) reduction can be stimulated most effectively with the addition of acetate. Although it had been speculated that microbial U(VI) reduction might be capable of this type of environmental remediation ever since the discovery of microbial U(VI) reduction, this had not been previously demonstrated under environmentally relevant conditions. (3) U(VI) is reduced concurrently with Fe(III) and prior to sulfate reduction. U(VI) and Fe(III) reduction proceeded concurrently, accompanied by a dramatic enrichment in organisms in the Geobacteraceae. Sulfate-reducing microorganisms do not appear to be important components of the microbial community reducing U(VI) in these subsurface sediments. (4) Nitrate has important influences on U(VI) reduction. Nitrate inhibits the reduction of metals until nitrate is depleted. Fe(III)-reducing microorganisms such as Geobacter metallireducens and Desulfitobacterium species can oxidize Fe(II) with the reduction of nitrate which is an important consideration because our previous studies have demonstrated that freshly precipitated Fe(III) oxides can reoxidize U(IV) to U(VI). The discovery that G. metallireducens can ''run backwards'' and oxidize U(IV) when nitrate is present reveals another mechanism preventing precipitation of U(IV) in the presence of nitrate as well as potential novel strategy for removing uranium from the subsurface after a site has been remediated. (5) Importance of understanding Fe(III) forms available for microbial reduction. Fe(III) is orders of magnitude more abundant than U(VI) as an

GeoViQua: quality-aware geospatial data discovery and evaluation

Science.gov (United States)

Bigagli, L.; Papeschi, F.; Mazzetti, P.; Nativi, S.

2012-04-01

GeoViQua (QUAlity aware VIsualization for the Global Earth Observation System of Systems) is a recently started FP7 project aiming at complementing the Global Earth Observation System of Systems (GEOSS) with rigorous data quality specifications and quality-aware capabilities, in order to improve reliability in scientific studies and policy decision-making. GeoViQua main scientific and technical objective is to enhance the GEOSS Common Infrastructure (GCI) providing the user community with innovative quality-aware search and evaluation tools, which will be integrated in the GEO-Portal, as well as made available to other end-user interfaces. To this end, GeoViQua will promote the extension of the current standard metadata for geographic information with accurate and expressive quality indicators, also contributing to the definition of a quality label (GEOLabel). GeoViQua proposed solutions will be assessed in several pilot case studies covering the whole Earth Observation chain, from remote sensing acquisition to data processing, to applications in the main GEOSS Societal Benefit Areas. This work presents the preliminary results of GeoViQua Work Package 4 "Enhanced geo-search tools" (WP4), started in January 2012. Its major anticipated technical innovations are search and evaluation tools that communicate and exploit data quality information from the GCI. In particular, GeoViQua will investigate a graphical search interface featuring a coherent and meaningful aggregation of statistics and metadata summaries (e.g. in the form of tables, charts), thus enabling end users to leverage quality constraints for data discovery and evaluation. Preparatory work on WP4 requirements indicated that users need the "best" data for their purpose, implying a high degree of subjectivity in judgment. This suggests that the GeoViQua system should exploit a combination of provider-generated metadata (objective indicators such as summary statistics), system-generated metadata (contextual

Immobilization of Cr(Vi) as a contaminant from soil by iron compounds; Inmovilizacion de Cr(VI) como contaminante del suelo por compuestos de hierro

Energy Technology Data Exchange (ETDEWEB)

Marin A, M. de J.; Romero G, E. T. [ININ, Carretera Mexico-Toluca s/n, Ocoyoacac 52750, Estado de Mexico (Mexico); Reyes G, L. R. [Universidad Autonoma del Estado de Hidalgo, Centro de Investigacion en Ciencias de la Tierra, Carretera Pachuca-Tulancingo Km. 4.5, Pachuca 42184, Hidalgo (Mexico)], e-mail: elizabeth.romero@inin.gob.mx

2008-07-01

The objective of this research was to determine the physicochemical and surface properties of Fe{sup 0} and FeS to select the appropriate radioactive material for use in the design of artificial barriers or walls and remove Cr (Vi). The physicochemical characterization was carried out of iron: Fe{sup 0} and FeS, using scanning electron microscopy of high vacuum, X-ray diffraction and thermal gravimetric analysis techniques. As for the characterization of the surface, was used to determine the surface area, point of zero charge, density of active sites and kinetics of moisture. We obtained a solution of Cr (Vi) by elution of deionized water on the pollution land of Buenavista, Guanajuato. The concentration of Cr (Vi) from a stock solution was 55.56 mg / L determined by UV-Vis spectrophotometry. Stripping or maximum immobilization of Cr (Vi) with Fe{sup 0} (material chosen by their physicochemical and surface properties) was 68.25% using Fe{sup 0}, at a concentration less than 0.1, ph equal to 3 and a contact time of 24 hours. (Author)

Ferric chloride modified zeolite in wastewater on Cr (VI) adsorption characteristics

Science.gov (United States)

Wu, Xiaoqing; Zhang, Kang; Chen, Wen; Zhang, Hua

2018-03-01

Zeolite was modified by ferric chloride(Fe-Z) removal Cr (VI) ion from wastewater. The results showed that the effect of Cr(VI) adsorption on modified zeolite depended significantly on pH. It is favorable for the adsorption of Cr(VI) in acid condition. The Langmuir isotherm model has high fitting accuracy with experimental data, demonstrated that is monolayer adsorption and chemical adsorption.The pseudo-second-order equation provided the best correlation to the data. The model can describe the adsorption reaction process well.

29 CFR 1910.1026 - Chromium (VI).

Science.gov (United States)

2010-07-01

... allows employees to consume food or beverages at a worksite where chromium (VI) is present, the employer... effect on productivity. 2. Plating Bath Surface Tension Management and Fume Suppression • Lower surface...

Validación de un ELISA tipo inhibición para cuantificar polisacárido Vi en la vacuna antitifoídica cubana vax-TyVi

Directory of Open Access Journals (Sweden)

Esther María Fajardo

2006-08-01

Full Text Available Se describe la validación de un ELISA tipo inhibición, reportado por primera vez en la literatura científica para cuantificar un antígeno vacunal: el polisacárido Vi de Salmonella Typhi, para ser empleado en el control de la calidad de la vacuna antitifoídica cubana vax- TyViâ. El ensayo consta de seis pasos: 1 Recubrimiento de placa de reacción con poli-L-lisina y posteriormente polisacárido Vi; 2 Bloqueo con leche descremada; 3 Inhibición o neutralización en tubos de suero anti-Vi de conejo, respectivamente, con polisacárido Vi de Curva de Calibración (concentraciones desde 1–32 μg/mL, control positivo y muestras de vacuna (3 diluciones; 4 Neutralización de anticuerpos anti-Vi libres, presentes en las mezclas anteriores, por el Polisacárido de Recubrimiento; 5 Reconocimiento de anticuerpos anti-Vi unidos a la placa (conjugado anti-IgG de conejo-fosfatasa alcalina y 6 Revelado por reacción enzima-sustrato. Los parámetros de validación estudiados y sus resultados fueron: 1 Precisión, expresada como coeficiente de variación a tres niveles de concentración de polisacárido, comprendidos en el rango de su especificación (35, 50 y 70 μg/mL y evaluada en términos de repetibilidad; precisión intraensayos (cuatro analistas y reproducibilidad (seis analistas: £ 20%; 2 Linealidad (100*R2: 99,68 %; 3 Límite de detección: 0,5 μg/mL; 4 Exactitud (recuperación para las tres diluciones de la muestra: entre 100 y 118%, y 5 Robustez: no influye 1,5 h de bloqueo (p = 0,52 ni ± 5 min para leer placa (p = 0,56; influye grandemente la calidad del agua (p = 0,026, a favor del agua para inyección. El ensayo es adecuado para los fines propuestos y es una medida de la inmunogenicidad in vitro del polisacárido Vi.