WorldWideScience

Sample records for fabricating geometrically-complex components

  1. Flexible Production of Geometrically Complex Superalloy Components, Phase II

    Data.gov (United States)

    National Aeronautics and Space Administration — In order to design and manufacture complex, one-of-a-kind to limited quantity rocket propulsion system components, while shortening the development cycle time and...

  2. Flexible Production of Geometrically Complex Superalloy Components, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — In order to design and manufacture complex, one-of-a-kind to limited quantity rocket propulsion system components, while shortening the development cycle time and...

  3. Fabricating nuclear components

    International Nuclear Information System (INIS)

    Anon.

    1977-01-01

    Activities of the Nuclear Engineering Division of Vickers Ltd., particularly fabrication of long slim tubular components for power reactors and the construction of irradiation loops and rigs, are outlined. The processes include hydraulic forming for fabrication of various types of tubes and outer cases of fuel transfer buckets, various specialised welding operations including some applications of the TIG process, and induction brazing of specialised assemblies. (U.K.)

  4. Refractory alloy component fabrication

    International Nuclear Information System (INIS)

    Young, W.R.

    1984-01-01

    Purpose of this report is to describe joining procedures, primarily welding techniques, which were developed to construct reliable refractory alloy components and systems for advanced space power systems. Two systems, the Nb-1Zr Brayton Cycle Heat Receiver and the T-111 Alloy Potassium Boiler Development Program, are used to illustrate typical systems and components. Particular emphasis is given to specific problems which were eliminated during the development efforts. Finally, some thoughts on application of more recent joining technology are presented. 78 figures

  5. Plasmonic components fabrication via nanoimprint

    DEFF Research Database (Denmark)

    Boltasseva, Alexandra

    2009-01-01

    A review report on nanoimprinted plasmonic components is given. The fabrication of different metal–dielectric geometries and nanostructured surfaces that support either propagating or localized surface plasmon modes is discussed. The main characteristics and advantages of the nanoimprint technology...... for the fabrication of various plasmonic structures are outlined. The discussion of plasmonic waveguiding structures focuses on planar waveguides based on metal strips embedded into a dielectric and on profiled metal surfaces. Nanoimprint-based fabrication of two-dimensional nanostructured plasmonic surfaces...... for enhanced transmission studies and sensor applications is also discussed. Throughout the report, the main fabrication schemes are described, as well as the challenges facing future manufacturing of plasmonic components for device applications....

  6. Simulating geometrically complex blast scenarios

    Directory of Open Access Journals (Sweden)

    Ian G. Cullis

    2016-04-01

    Full Text Available The effects of blast waves generated by energetic and non-energetic sources are of continuing interest to the ballistics research community. Modern conflicts are increasingly characterised by asymmetric urban warfare, with improvised explosive devices (IEDs often playing a dominant role on the one hand and an armed forces requirement for minimal collateral effects from their weapons on the other. These problems are characterised by disparate length- and time-scales and may also be governed by complex physics. There is thus an increasing need to be able to rapidly assess and accurately predict the effects of energetic blast in topologically complex scenarios. To this end, this paper presents a new QinetiQ-developed advanced computational package called EAGLE-Blast, which is capable of accurately resolving the generation, propagation and interaction of blast waves around geometrically complex shapes such as vehicles and buildings. After a brief description of the numerical methodology, various blast scenario simulations are described and the results compared with experimental data to demonstrate the validation of the scheme and its ability to describe these complex scenarios accurately and efficiently. The paper concludes with a brief discussion on the use of the code in supporting the development of algorithms for fast running engineering models.

  7. Fabrication of plastic microfluidic components

    Science.gov (United States)

    Martin, Peter M.; Matson, Dean W.; Bennett, Wendy D.; Hammerstrom, D. J.

    1998-09-01

    Plastic components have many advantages, including ease of fabrication, low cost, chemical inertness, lightweight, and disposability. We report on the fabrication of three plastics-based microfluidic components: a motherboard, a dialysis unit, and a metal sensor. Microchannels, headers, and interconnects were produced in thin sheets (>=50 microns) of polyimide, PMMA, polyethylene, and polycarbonate using a direct-write excimer laser micromachining system. Machined sheets were laminated by thermal and adhesive bonding to form leak-tight microfluidic components. The microfluidic motherboard borrowed the `functionality on a chip' concept from the electronics industry and was the heart of a complex microfluidic analytical device. The motherboard platform was designed to be tightly integrated and self-contained (i.e., liquid flows are all confined within machined microchannels), reducing the need for tubing with fluid distribution and connectivity. This concept greatly facilitated system integration and miniaturization. As fabricated, the motherboard consisted of three fluid reservoirs connected to micropumps by microchannels. The fluids could either be pumped independently or mixed in microchannels prior to being directed to exterior analytical components via outlet ports. The microdialysis device was intended to separate electrolytic solutes from low volume samples prior to mass spectrometric analysis. The device consisted of a dialysis membrane laminated between opposed serpentine microchannels containing the sample fluid and a buffer solution. The laminated metal sensor consisted of fluid reservoirs, micro-flow channels, micropumps, mixing channels, reaction channels, and detector circuitry.

  8. Fabricating plasmonic components for nanophotonics

    DEFF Research Database (Denmark)

    Boltasseva, Alexandra; Nielsen, Rasmus Bundgaard; Jeppesen, Claus

    2009-01-01

    We report on experimental realization of different metal-dielectric structures that are used as surface plasmon polariton waveguides and as plasmonic metamaterials. Fabrication approaches based on different lithographic and deposition techniques are discussed.......We report on experimental realization of different metal-dielectric structures that are used as surface plasmon polariton waveguides and as plasmonic metamaterials. Fabrication approaches based on different lithographic and deposition techniques are discussed....

  9. Automated laser fabrication of cemented carbide components

    Science.gov (United States)

    Paul, C. P.; Khajepour, A.

    2008-07-01

    Automated Laser Fabrication (ALFa) is one of the most rapidly growing rapid-manufacturing technologies. It is similar to laser cladding at process level with different end applications. In general, laser cladding technique is used to deposit materials on the substrate either to improve the surface properties or to refurbish the worn-out parts, while ALFa is capable of near net shaping the components by layer-by-layer deposition of the material directly from CAD model. This manufacturing method is very attractive for low volume manufacturing of hard materials, as near net shaping minimizes machining of hard material and subsequently brings significant savings in time and costly material. To date, many researchers have used this technology to fabricate components using various alloy steels, nickel-based alloys and cobalt-based alloys. In the present study, the work is extended to tungsten carbide cobalt (WC-Co) composites. A set of comprehensive experiments was carried out to study the effect of processing parameters during multi-layer fabrication. The process parameters were optimized for the component-level fabrication. Fabricated components were subjected to dye-penetrant testing, three-point flexural testing, hardness measurement, optical and scanning electron microscopy and X-ray diffraction analysis. The test results revealed that the laser-fabricated material was defect free and more ductile in nature. Thus, ALFa technology, not only produced the quality components, but also minimized machining of hard material and brought significant saving of time and costly WC-Co material.

  10. Directed light fabrication of rhenium components

    Energy Technology Data Exchange (ETDEWEB)

    Milewski, J.O.; Thoma, D.J.; Lewis, G.K.

    1997-02-01

    Directed Light Fabrication (DLF) is a direct metal deposition process that fuses powder, delivered by gas into the focal zone of a high powered laser beam to form fully dense near-net shaped components. This is accomplished in one step without the use of molds, dies, forming, pressing, sintering or forging equipment. DLF is performed in a high purity inert environment free from the contaminants associated with conventional processing such as oxide and carbon pickup, lubricants, binding agents, cooling or cleaning agents. Applications using rhenium have historically been limited in part by its workability and cost. This study demonstrates the ability to fuse rhenium metal powder, using a DLF machine, into free standing rods and describes the associated parameter study. Microstructural comparisons between DLF deposited rhenium and commercial rhenium sheet product is performed. This research combined with existing DLF technology demonstrates the feasibility of forming complex rhenium, metal shapes directly from powder.

  11. Design and Fabrication of Photonic Crystal Materials and Components

    DEFF Research Database (Denmark)

    Harpøth, Anders

    2005-01-01

    The work described in this thesis covers the issues of producing materials for use as base material for fabricating photonic crystals and the design, fabrication and characterization of photonic crystal components. One of the aims is to investigate the possibilities of fabricating a silicon...... approaches to improve the performance of selected components have been carried out, by applying a method adopted from mechanical engineering called topology optimization. Also different approaches have been applied in order to investigate the loss in a cavity resonator. Finally, the fabrication of several...... components has been carried out with a subsequent characterization of the fabricated components....

  12. 49 CFR 192.153 - Components fabricated by welding.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 3 2010-10-01 2010-10-01 false Components fabricated by welding. 192.153 Section....153 Components fabricated by welding. (a) Except for branch connections and assemblies of standard... welding, whose strength cannot be determined, must be established in accordance with paragraph UG-101 of...

  13. Mechanical components: fabrication of major reactor structures

    International Nuclear Information System (INIS)

    Nicholson, S.

    1985-01-01

    The paper examines the validity of criticisms of quality assurance of mechanical plant and welded products within major reactor structures, taking into account experience gained on the AGR's. Various constructive recommendations are made aimed at furthering the objectives of quality assurance in the nuclear industry and making it more cost-effective. Current levels of quality related costs in the fabrication industry are provided as a basis for discussion. (U.K.)

  14. Information Geometric Complexity of a Trivariate Gaussian Statistical Model

    Directory of Open Access Journals (Sweden)

    Domenico Felice

    2014-05-01

    Full Text Available We evaluate the information geometric complexity of entropic motion on low-dimensional Gaussian statistical manifolds in order to quantify how difficult it is to make macroscopic predictions about systems in the presence of limited information. Specifically, we observe that the complexity of such entropic inferences not only depends on the amount of available pieces of information but also on the manner in which such pieces are correlated. Finally, we uncover that, for certain correlational structures, the impossibility of reaching the most favorable configuration from an entropic inference viewpoint seems to lead to an information geometric analog of the well-known frustration effect that occurs in statistical physics.

  15. Progress in ceramic component fabrication technology

    Science.gov (United States)

    Storm, R. S.; Lashway, R. W.

    1982-01-01

    Net shape techniques have been used in the production of rotating and static vehicular engine high-temperature components composed of sintered Alpha-SiC (SASC). Injection-molded rotors have been cold spin tested, as well as a slip-cast combustor assembly hot rig. SASC pistons and cylinder liners have also been constructed for an opposed piston, two-cycle diesel test rig while test results are presented. An uncooled, minimum-friction internal combustion engine with multi-fuel capability due to its elevated combustion temperatures appears to be achievable in the near term by means of SASC techniques. The flexural strength of SASC at 1500 C is 446 MPa, identical to that at room temperature, and excellent strength retention has been demonstrated after 3500 hours of cyclic exposure.

  16. Design and Fabrication of SOI-based photonic crystal components

    DEFF Research Database (Denmark)

    Borel, Peter Ingo; Frandsen, Lars Hagedorn; Harpøth, Anders

    2004-01-01

    We present examples of ultra-compact photonic crystal components realized in silicon-on-insulator material. We have fabricated several different types of photonic crystal waveguide components displaying high transmission features. This includes 60° and 120° bends, different types of couplers......, and splitters. Recently, we have designed and fabricated components with more than 200 nm bandwidths. Design strategies to enhance the performance include systematic variation of design parameters using finite-difference time-domain simulations and inverse design methods such as topology optimization....

  17. Optimization benefits analysis in production process of fabrication components

    Science.gov (United States)

    Prasetyani, R.; Rafsanjani, A. Y.; Rimantho, D.

    2017-12-01

    The determination of an optimal number of product combinations is important. The main problem at part and service department in PT. United Tractors Pandu Engineering (shortened to PT.UTPE) Is the optimization of the combination of fabrication component products (known as Liner Plate) which influence to the profit that will be obtained by the company. Liner Plate is a fabrication component that serves as a protector of core structure for heavy duty attachment, such as HD Vessel, HD Bucket, HD Shovel, and HD Blade. The graph of liner plate sales from January to December 2016 has fluctuated and there is no direct conclusion about the optimization of production of such fabrication components. The optimal product combination can be achieved by calculating and plotting the amount of production output and input appropriately. The method that used in this study is linear programming methods with primal, dual, and sensitivity analysis using QM software for Windows to obtain optimal fabrication components. In the optimal combination of components, PT. UTPE provide the profit increase of Rp. 105,285,000.00 for a total of Rp. 3,046,525,000.00 per month and the production of a total combination of 71 units per unit variance per month.

  18. Mastering the design technology of NPP component fabrication

    International Nuclear Information System (INIS)

    Popov, L.I.

    1986-01-01

    The problems of mastering and improvement of the technology of NPP component fabrication are discussed. Main methods for improvement of storing, thermal, welding, mechano-assemblying and instrumental productions as well as means of mechanization and automation of the production and methods for quality control are considered

  19. Modeling fabrication of nuclear components: An integrative approach

    Energy Technology Data Exchange (ETDEWEB)

    Hench, K.W.

    1996-08-01

    Reduction of the nuclear weapons stockpile and the general downsizing of the nuclear weapons complex has presented challenges for Los Alamos. One is to design an optimized fabrication facility to manufacture nuclear weapon primary components in an environment of intense regulation and shrinking budgets. This dissertation presents an integrative two-stage approach to modeling the casting operation for fabrication of nuclear weapon primary components. The first stage optimizes personnel radiation exposure for the casting operation layout by modeling the operation as a facility layout problem formulated as a quadratic assignment problem. The solution procedure uses an evolutionary heuristic technique. The best solutions to the layout problem are used as input to the second stage - a simulation model that assesses the impact of competing layouts on operational performance. The focus of the simulation model is to determine the layout that minimizes personnel radiation exposures and nuclear material movement, and maximizes the utilization of capacity for finished units.

  20. Two-component microinjection moulding for MID fabrication

    DEFF Research Database (Denmark)

    Islam, Aminul; Hansen, Hans Nørgaard; Tang, Peter Torben

    2010-01-01

    Moulded interconnect devices (MIDs) are plastic substrates with electrical infrastructure. The fabrication of MIDs is usually based on injection moulding, and different process chains may be identified from this starting point. The use of MIDs has been driven primarily by the automotive sector......-component injection moulding and subsequent metallisation. This technology promises cost effective and convergent manufacturing approaches for both macro- and microapplications. This paper presents the results of industrial MID production based on two-component injection moulding and discusses the important issues...

  1. Two component micro injection molding for MID fabrication

    DEFF Research Database (Denmark)

    Islam, Mohammad Aminul; Hansen, Hans Nørgaard; Tang, Peter Torben

    2009-01-01

    Molded Interconnect Devices (MIDs) are plastic substrates with electrical infrastructure. The fabrication of MIDs is usually based on injection molding and different process chains may be identified from this starting point. The use of MIDs has been driven primarily by the automotive sector......, but recently the medical sector seems more and more interested. In particular the possibility of miniaturization of 3D components with electrical infrastructure is attractive. The paper describes possible manufacturing routes and challenges of miniaturized MIDs based on two component micro injection molding...

  2. The fabrication of nozzles for nuclear components by welding

    International Nuclear Information System (INIS)

    Moraes, M.M.; Krausser, P.; Echeverria, J.A.V.

    1986-01-01

    A nozzle with medium outside diameter of 1000 mm and medium thickness of 150 mm composed integrally by deposited metal by submerged-arc (wire S3NiMo1, 0.5mm) was fabricated in NUCLEP. The nondestructive, mechanical, metallographic and chemical testing carried out in a test sample made by the same procedure and welding parameters, showed results according to specifications established for primary components for nuclear power plants, and the tests presented mechanical properties and tenacity better than similar nozzle samples. This nozzle is cheapest concerning to importations, in respecting to its forged similar. (M.C.K.) [pt

  3. Fabrication of Complex Optical Components From Mold Design to Product

    CERN Document Server

    Riemer, Oltmann; Gläbe, Ralf

    2013-01-01

    High quality optical components for consumer products made of glass and plastic are mostly fabricated by replication. This highly developed production technology requires several consecutive, well-matched processing steps called a "process chain" covering all steps from mold design, advanced machining and coating of molds, up to the actual replication and final precision measurement of the quality of the optical components. Current market demands for leading edge optical applications require high precision and cost effective parts in large volumes. For meeting these demands it is necessary to develop high quality process chains and moreover, to crosslink all demands and interdependencies within these process chains. The Transregional Collaborative Research Center "Process chains for the replication of complex optical elements" at Bremen, Aachen and Stillwater worked extensively and thoroughly in this field from 2001 to 2012. This volume will present the latest scientific results for the complete process chain...

  4. Inertial Confinement Fusion Target Component Fabrication and Technology Development report

    International Nuclear Information System (INIS)

    Steinman, D.

    1994-03-01

    On December 30, 1990, the US Department of Energy entered into a contract with General Atomics (GA) to be the Inertial Confinement Fusion Target Component Fabrication and Technology Development Support contractor. This report documents the technical activities which took place under this contract during the period of October 1, 1992 through September 30, 1993. During this period, GA was assigned 18 tasks in support of the Inertial Confinement Fusion program and its laboratories. These tasks included ''Capabilities Activation'' and ''Capabilities Demonstration'' to enable us to begin production of glass and composite polymer capsules. Capsule delivery tasks included ''Small Glass Shell Deliveries'' and ''Composite Polymer Capsules'' for Lawrence Livermore National Laboratory (LLNL) and Los Alamos National Laboratory (LANL). We also were asked to provide direct ''Onsite Support'' at LLNL and LANL. We continued planning for the transfer of ''Micromachining Equipment from Rocky Flats'' and established ''Target Component Micromachining and Electroplating Facilities'' at GA. We fabricated over 1100 films and filters of 11 types for Sandia National Laboratory and provided full-time onsite engineering support for target fabrication and characterization. We initiated development of methods to make targets for the Naval Research Laboratory. We investigated spherical interferometry, built an automated capsule sorter, and developed an apparatus for calorimetric measurement of fuel fill for LLNL. We assisted LANL in the ''Characterization of Opaque b-Layered Targets.'' We developed deuterated and UV-opaque polymers for use by the University of Rochester's Laboratory for Laser Energetics (UR/LLE) and devised a triple-orifice droplet generator to demonstrate the controlled-mass nature of the microencapsulation process

  5. On P vs. NP, Geometric Complexity Theory, Explicit Proofs and the Complexity Barrier

    OpenAIRE

    Mulmuley, Ketan D.

    2009-01-01

    Geometric complexity theory (GCT) is an approach to the P vs. NP and related problems. This article gives its complexity theoretic overview without assuming any background in algebraic geometry or representation theory.

  6. Prediction of Corrosion of Advanced Materials and Fabricated Components

    Energy Technology Data Exchange (ETDEWEB)

    A. Anderko; G. Engelhardt; M.M. Lencka (OLI Systems Inc.); M.A. Jakab; G. Tormoen; N. Sridhar (Southwest Research Institute)

    2007-09-29

    The goal of this project is to provide materials engineers, chemical engineers and plant operators with a software tool that will enable them to predict localized corrosion of process equipment including fabricated components as well as base alloys. For design and revamp purposes, the software predicts the occurrence of localized corrosion as a function of environment chemistry and assists the user in selecting the optimum alloy for a given environment. For the operation of existing plants, the software enables the users to predict the remaining life of equipment and help in scheduling maintenance activities. This project combined fundamental understanding of mechanisms of corrosion with focused experimental results to predict the corrosion of advanced, base or fabricated, alloys in real-world environments encountered in the chemical industry. At the heart of this approach is the development of models that predict the fundamental parameters that control the occurrence of localized corrosion as a function of environmental conditions and alloy composition. The fundamental parameters that dictate the occurrence of localized corrosion are the corrosion and repassivation potentials. The program team, OLI Systems and Southwest Research Institute, has developed theoretical models for these parameters. These theoretical models have been applied to predict the occurrence of localized corrosion of base materials and heat-treated components in a variety of environments containing aggressive and non-aggressive species. As a result of this project, a comprehensive model has been established and extensively verified for predicting the occurrence of localized corrosion as a function of environment chemistry and temperature by calculating the corrosion and repassivation potentials.To support and calibrate the model, an experimental database has been developed to elucidate (1) the effects of various inhibiting species as well as aggressive species on localized corrosion of nickel

  7. Multi-Step Deep Reactive Ion Etching Fabrication Process for Silicon-Based Terahertz Components

    Science.gov (United States)

    Jung-Kubiak, Cecile (Inventor); Reck, Theodore (Inventor); Chattopadhyay, Goutam (Inventor); Perez, Jose Vicente Siles (Inventor); Lin, Robert H. (Inventor); Mehdi, Imran (Inventor); Lee, Choonsup (Inventor); Cooper, Ken B. (Inventor); Peralta, Alejandro (Inventor)

    2016-01-01

    A multi-step silicon etching process has been developed to fabricate silicon-based terahertz (THz) waveguide components. This technique provides precise dimensional control across multiple etch depths with batch processing capabilities. Nonlinear and passive components such as mixers and multipliers waveguides, hybrids, OMTs and twists have been fabricated and integrated into a small silicon package. This fabrication technique enables a wafer-stacking architecture to provide ultra-compact multi-pixel receiver front-ends in the THz range.

  8. Fabrication of micro-optical components using femtosecond oscillator pulses

    Science.gov (United States)

    Rodrigues, Vanessa R. M.; Ramachandran, Hema; Chidangil, Santhosh; Mathur, Deepak

    2017-06-01

    With a penchant for integrated photonics and miniaturization, the fabrication of micron sized optical elements using precision laser pulse management is drawing attention due to the possibility of minimizing tolerances for collateral material damage. The work presented here deals with the design, fabrication and characterization of a range of diffractive optics - gratings, grids and Fresnel zone plates - on transparent and metallic samples. Their low volume, light weight, transmission bandwidth, high damage threshold and flexible design make them suited for replacing conventional refractive optical elements. Our one-step, mask-less, 3-D laser direct writing process is a green fabrication technique which is in stark contrast to currently popular Photo-lithography based micro-structuring. Our method provides scope for modifications on the surface as well as within the bulk of the material. The mechanism involved in the fabrication of these optics on transparent and thin metallic substrates differ from each other. Our studies show that both amplitude and phase versions of micro-structures were achieved successfully with performances bearing 98% accuracy vis-a-vis theoretical expectations.

  9. Fabrication details for wire wrapped fuel assembly components

    International Nuclear Information System (INIS)

    Bosy, B.J.

    1978-09-01

    Extensive hydraulic testing of simulated LMFBR blanket and fuel assemblies is being carried out under this MIT program. The fabrication of these test assemblies has involved development of manufacturing procedures involving the wire wrapped pins and the flow housing. The procedures are described in detail in the report

  10. Fabrication development of full-sized components for GCFR core assemblies

    International Nuclear Information System (INIS)

    Lindgren, J.R.; Flynn, P.W.; Foster, L.C.

    1980-05-01

    This paper presents the status of the development of full-sized components for gas-cooled fast reactor (GCFR) core assemblies. Methods for ribbing of the fuel rod cladding, fabrication of grid spacers of two different designs, drawing of assembly flow ducts, and fabrication of fission gas collection manifolds by several methods are discussed

  11. KHIC's experience in the design and fabrication of nuclear components

    International Nuclear Information System (INIS)

    Suh, S.-C.

    1992-01-01

    Since 1980, Korea Heavy Industries ampersand Construction Company, Ltd. (KHIC) has specialized in the design and equipment supply for nuclear power facilities in Korea. In April 1987, KHIC became the prime contractor for the construction of Yonggwang 3 ampersand 4 (YGN 3 ampersand 4) nuclear power project. Accordingly, KHIC's technological self-reliance capability for the manufacturing processes of the primary system equipment and components has increased from 18% during the initial stage of Yonggwang 1 ampersand 2 (YGN 1 ampersand 2) project to 63% for YGN 3 ampersand 4 project. Self-reliance capability for the secondary system equipment and components has increased from 28% to 84% during the same period of time as well. The ultimate goal is to achieve complete and total assurance that our products are of the finest quality in the nuclear industry in the world market. Henceforth, we will be able to guarantee complete customer satisfaction and reliability of our products with safety assurance and leading edge technology

  12. Innovative three-dimensional neutronics analyses directly coupled with cad models of geometrically complex fusion systems

    International Nuclear Information System (INIS)

    Sawan, M.; Wilson, P.; El-Guebaly, L.; Henderson, D.; Sviatoslavsky, G.; Bohm, T.; Kiedrowski, B.; Ibrahim, A.; Smith, B.; Slaybaugh, R.; Tautges, T.

    2007-01-01

    Fusion systems are, in general, geometrically complex requiring detailed three-dimensional (3-D) nuclear analysis. This analysis is required to address tritium self-sufficiency, nuclear heating, radiation damage, shielding, and radiation streaming issues. To facilitate such calculations, we developed an innovative computational tool that is based on the continuous energy Monte Carlo code MCNP and permits the direct use of CAD-based solid models in the ray-tracing. This allows performing the neutronics calculations in a model that preserves the geometrical details without any simplification, eliminates possible human error in modeling the geometry for MCNP, and allows faster design iterations. In addition to improving the work flow for simulating complex 3- D geometries, it allows a richer representation of the geometry compared to the standard 2nd order polynomial representation. This newly developed tool has been successfully tested for a detailed 40 degree sector benchmark of the International Thermonuclear Experimental Reactor (ITER). The calculations included determining the poloidal variation of the neutron wall loading, flux and nuclear heating in the divertor components, nuclear heating in toroidal field coils, and radiation streaming in the mid-plane port. The tool has been applied to perform 3-D nuclear analysis for several fusion designs including the ARIES Compact Stellarator (ARIES-CS), the High Average Power Laser (HAPL) inertial fusion power plant, and ITER first wall/shield (FWS) modules. The ARIES-CS stellarator has a first wall shape and a plasma profile that varies toroidally within each field period compared to the uniform toroidal shape in tokamaks. Such variation cannot be modeled analytically in the standard MCNP code. The impact of the complex helical geometry and the non-uniform blanket and divertor on the overall tritium breeding ratio and total nuclear heating was determined. In addition, we calculated the neutron wall loading variation in

  13. Development of technology on natural flaw fabrication and precise diagnosis for the major components in NPPs

    International Nuclear Information System (INIS)

    Han, Jung Ho; Choi, Myung Sik; Lee, Doek Hyun; Hur, Do Haeng

    2002-01-01

    The objective of this research is to develop a fabrication technology of natural flaw specimen of major components in NPPs and a technology of precise diagnosis for failure and degradation of components using natural flaw specimen. 1) Successful development of the natural flaw fabrication technology of SG tube 2) Evaluation of ECT signal and development of precise diagnosis using natural flaws. - Determination of length, depth, width, and multiplicity of fabricated natural flaws. - Informations about detectability and accuracy of ECT evaluation on various kinds of defects are collected when the combination of probe and frequency is changed. - An advanced technology for precise ECT evaluation is established. 3) Application of precise ECT diagnosis to failure analysis of SG tube in operation. - Fretting wear of KSNP SG. - ODSCC at tube expanded region of KSNP SG. - Determination of through/non-through wall of axial crack

  14. Effect of components (polymer, plasticizer and solvent as a variable in fabrication of diclofenac transdermal patch

    Directory of Open Access Journals (Sweden)

    Chetna Modi

    2012-01-01

    Full Text Available Transdermal drug delivery influence consumer acceptance and marked increase in bioavailability of some drugs which undergoes hepatic first-pass metabolism. Fabrication of transdermal patch requires lots of attention regarding the amount of components used for it. Because of varied nature of polymer and plasticizer, transdermal patches have different properties and different drug release. This study is on the basis to evaluate the amount to be needed for fabrication of diclofenac transdermal patch. Study shows that Hydroxy Propyl Methyl Cellulose has great influence on transdermal patch, if it is used alone in combination with glycerin or PEG-4000 plasticizer.

  15. Cold Gas Dynamic Manufacturing - A New Approach to Near-Net Shape Metal Component Fabrication

    Science.gov (United States)

    2003-04-01

    transformations introduce further complications in the fabrication of Functionally Graded Material ( FGM ) components or the utilisation of novel nanocrystalline...reducing the gas velocity. Finally, the jet impacts the substrate plate and is decelerated to almost zero velocity in the axial direction. Particles...around its base allow the nozzle and chamber to slide as one along a ground base plate Powder Feed Inlet Process Gas Inlet High Speed Deposition

  16. GEOMETRIC COMPLEXITY ANALYSIS IN AN INTEGRATIVE TECHNOLOGY EVALUATION MODEL (ITEM FOR SELECTIVE LASER MELTING (SLM#

    Directory of Open Access Journals (Sweden)

    S. Merkt

    2012-01-01

    Full Text Available

    ENGLISH ABSTRACT: Selective laser melting (SLM is becoming an economically viable choice for manufacturing complex serial parts. This paper focuses on a geometric complexity analysis as part of the integrative technology evaluation model (ITEM presented here. In contrast to conventional evaluation methodologies, the ITEM considers interactions between product and process innovations generated by SLM. The evaluation of manufacturing processes that compete with SLM is the main goal of ITEM. The paper includes a complexity analysis of a test part from Festo AG. The paper closes with a discussion of how the expanded design freedom of SLM can be used to improve company operations, and how the complexity analysis presented here can be seen as a starting point for feature-based complexity analysis..

    AFRIKAANSE OPSOMMING: Selektiewe lasersmelting word geleidelik ’n gangbare ekonomiese keuse vir die vervaar-diging van opeenvolgende komplekse onderdele. Die navorsing is toegespits op die ontleding van meetkundige kompleksiteit as ’n gedeelte van ’n integrerende tegnologiese evalueringsmodel. Gemeet teen konvensionele evalueringsmodelle behandel die genoemde metode interaksies tussen produkte- en prosesinnovasies wat gegenereer word. Die navorsing behandel ’n kompleksiteitsontleding van ’n toetsonderdeel van die firma FESTO AG. Die resultaat toon hoe kompleksiteits-analise gebruik kan word as die vertrekpunt vir eienskapsgebaseerde analise.

  17. Fabrication of a resin appliance with alloy components using digital technology without an analog impression.

    Science.gov (United States)

    Al Mortadi, Noor; Jones, Quentin; Eggbeer, Dominic; Lewis, Jeffrey; Williams, Robert J

    2015-11-01

    The aim of this study was to fabricate a resin appliance incorporating "wire" components without the use of an analog impression and dental casts using an intraoral scanner and computer technology to build the appliance. This unique alignment of technology offers an enormous reduction in the number of fabrication steps when compared with more traditional methods of manufacture. The prototype incorporated 2 Adams clasps and a fitted labial bow. The alloy components were built from cobalt-chromium in an initial powdered form using established digital technology methods and then inserted into a build of a resin base plate. This article reports the first known use of computer-aided design and additive manufacture to fabricate a resin and alloy appliance, and constitutes proof of the concept for such manufacturing. The original workflow described could be seen as an example for many other similar appliances, perhaps with active components. The scan data were imported into an appropriate specialized computer-aided design software, which was used in conjunction with a force feedback (haptic) interface. The appliance designs were then exported as stereolithography files and transferred to an additive manufacturing machine for fabrication. The results showed that the applied techniques may provide new manufacturing and design opportunities in orthodontics and highlights the need for intraoral-specific additive manufacture materials to be produced and tested for biocompatibility compliance. In a trial, the retainer was fitted orally and judged acceptable by the clinician according to the typical criteria when placing such appliances in situ. Copyright © 2015 American Association of Orthodontists. Published by Elsevier Inc. All rights reserved.

  18. Net shape fabrication of stainless-steel micro machine components from metallic powder

    International Nuclear Information System (INIS)

    Imbaby, M; Jiang, K; Chang, I

    2008-01-01

    A fabrication process of the net shape 316-L stainless-steel micro machine components is reported. The fabrication process combines softlithography and powder metallurgy to produce microcomponents of complex geometries of high quality. The process starts with softlithography by producing ultra thick SU-8 master moulds and their negative replicas of polydimethylsiloxane (PDMS). Then stainless-steel slurry is prepared by mixing super fine 316-L steel powder and binder to fill the PDMS moulds. The two binders used in the experiments were Duramax D-3005 and a mixture of B1000 and B1007. The PDMS micro moulds are filled with the metallic slurries and green parts are obtained from de-moulding, before going through de-binding and sintering in forming gas atmosphere. The fabrication steps were repeatedly tested. The resultant micro parts show high quality shape retention which is attributed to the quality of the SU-8 master moulds. The hardness property of the sintered microcomponents was tested with a micro indenter and a 200 g load was applied. The Vickers hardness of the sintered components was found to be about 255, which was higher than 225 of annealed 316L stainless steel and the two binders make little difference on the hardness of the sintered samples

  19. Fault-patch stress-transfer efficiency in presence of sub-patch geometric complexity

    KAUST Repository

    Zielke, Olaf

    2015-04-01

    It is well known that faults are not planar surfaces. Instead they exhibit self-similar or self-affine properties that span a wide range of spatial (sub-micrometer to tens-of-kilometer). This geometric fault roughness has a distinct impact on amount and distribution of stresses/strains induced in the medium and on other portions of the fault. However, when numerically simulated (for example in multi-cycle EQ rupture simulations or Coulomb failure stress calculations) this roughness is largely ignored: individual fault patches --the incremental elements that build the fault surface in the respective computer models-- are planar and fault roughness at this and lower spatial scales is not considered. As a result, the fault-patch stress-transfer efficiency may be systematically too large in those numerical simulations with respect to the "actual" efficiency level. Here, we investigate the effect of sub-patch geometric complexity on fault-patch stress-transfer efficiency. For that, we sub-divide a fault patch (e.g., 1x1km) into a large number of sub-patches (e.g., 20x20m) and determine amount of induced stresses at selected positions around that patch for different levels and realizations of fault roughness. For each fault roughness level, we compute mean and standard deviation of the induced stresses, enabling us to compute the coefficient of variation. We normalize those values with stresses from the corresponding single (planar) fault patch, providing scaling factors and their variability for stress transfer efficiency. Given a certain fault roughness that is assumed for a fault, this work provides the means to implement the sub-patch fault roughness into investigations based on fault-patch interaction schemes.

  20. Fabrication of high-alloy powders consisting of spherical particles from ultradispersed components

    Science.gov (United States)

    Samokhin, A. V.; Fadeev, A. A.; Sinayskiy, M. A.; Alekseev, N. V.; Tsvetkov, Yu. V.; Arzhatkina, O. A.

    2017-07-01

    It is shown that powders of a model high alloy consisting of spherical particles 25-50 μm in size can be synthesized from a starting ultradispersed powder, which is made of a mixture of the alloy components and is fabricated by the magnesiothermal reduction of metal chlorides in the potassium chloride melt. The synthesis includes the stages of microgranulation of an ultradispersed powder, heat treatment of microgranules, classification of the microgranules with the separation of microgranule fraction of 25-50 μm, spheroidization of the separated fraction in a thermal plasma flow, and classification with the separation of a fraction of micro- and submicrometer-sized particles.

  1. 10 CFR Appendix O to Part 110 - Illustrative List of Fuel Element Fabrication Plant Equipment and Components Under NRC's Export...

    Science.gov (United States)

    2010-01-01

    ... 10 Energy 2 2010-01-01 2010-01-01 false Illustrative List of Fuel Element Fabrication Plant... Appendix O to Part 110—Illustrative List of Fuel Element Fabrication Plant Equipment and Components Under NRC's Export Licensing Authority Note: Nuclear fuel elements are manufactured from source or special...

  2. Direct laser fabrication of three dimensional components using SC420 stainless steel

    International Nuclear Information System (INIS)

    Ravi, G.A.; Hao, X.J.; Wain, N.; Wu, X.; Attallah, M.M.

    2013-01-01

    Highlights: ► The feasibility of direct laser fabrication of SC402 alloy was studied. ► Three-dimensional (3D) components with varying thicknesses can be built using DLF to near net-shape. ► The build size and orientation affects the mechanical properties. ► Hot isostatic pressing can be used to homogenise the mechanical properties. - Abstract: Direct Laser Fabrication (DLF) has been used in the fabrication of three-dimensional (3D) near net-shape metallic parts using stainless steel SC420 powder. The mechanical properties and microstructure of the as-deposited SC420 and of hot isostatically pressed DLF builds were investigated as a function of deposition direction and sample size using tensile testing, scanning electron microscopy and X-ray diffraction. The influence of the build geometry and orientation on the microstructure and the mechanical properties was also assessed. From this work, it was evident that the DLF process can produce three dimensional parts with good mechanical properties (yield strength > 1000 MPa, tensile strength > 1400 MPa, elongation > 5%), which approach the properties of wrought products

  3. Fused Filament Fabrication of Prosthetic Components for Trans-Humeral Upper Limb Prosthetics

    Science.gov (United States)

    Lathers, Steven M.

    Presented below is the design and fabrication of prosthetic components consisting of an attachment, tactile sensing, and actuator systems with Fused Filament Fabrication (FFF) technique. The attachment system is a thermoplastic osseointegrated upper limb prosthesis for average adult trans-humeral amputation with mechanical properties greater than upper limb skeletal bone. The prosthetic designed has: a one-step surgical process, large cavities for bone tissue ingrowth, uses a material that has an elastic modulus less than skeletal bone, and can be fabricated on one system. FFF osseointegration screw is an improvement upon the current two-part osseointegrated prosthetics that are composed of a fixture and abutment. The current prosthetic design requires two invasive surgeries for implantation and are made of titanium, which has an elastic modulus greater than bone. An elastic modulus greater than bone causes stress shielding and overtime can cause loosening of the prosthetic. The tactile sensor is a thermoplastic piezo-resistive sensor for daily activities for a prosthetic's feedback system. The tactile sensor is manufactured from a low elastic modulus composite comprising of a compressible thermoplastic elastomer and conductive carbon. Carbon is in graphite form and added in high filler ratios. The printed sensors were compared to sensors that were fabricated in a gravity mold to highlight the difference in FFF sensors to molded sensors. The 3D printed tactile sensor has a thickness and feel similar to human skin, has a simple fabrication technique, can detect forces needed for daily activities, and can be manufactured in to user specific geometries. Lastly, a biomimicking skeletal muscle actuator for prosthetics was developed. The actuator developed is manufactured with Fuse Filament Fabrication using a shape memory polymer composite that has non-linear contractile and passive forces, contractile forces and strains comparable to mammalian skeletal muscle, reaction

  4. Field analysis and enhancement of multi-pole magnetic components fabricated on printed circuit board

    International Nuclear Information System (INIS)

    Chiu, K.-C.; Chen, C.-S.

    2007-01-01

    A multi-pole magnetic component magnetized with a fine magnetic pole pitch of less than 1 mm is very difficult to achieve by using traditional methods. Moreover, it requires a precise mechanical process and a complicated magnetization system. Different fine magnetic pole pitches of 300, 350 and 400 μm have been accomplished on 9-pole magnetic components through the printed circuit board (PCB) manufacturing technology. Additionally, another fine magnetic pole pitch of 500 μm was also fabricated on a dual-layered (DL) wire circuit structure to investigate the field enhancement. After measurements, a gain factor of 1.37 was obtained in the field strength. The field variations among different magnetic pole pitches were analyzed in this paper

  5. Pulsed TIG welding in the fabrication of nuclear components and structures

    International Nuclear Information System (INIS)

    Lucas, W.; Males, B.O.

    1979-01-01

    TIG welding is an important welding technique in nuclear plant fabrication for the welding of critical components and structures where a high level of weld integrity is demanded. Whilst the process is ideally suited to precision welding, since the arc is a small intense heat source, it has proved to be somewhat intolerant to production variations in 'difficult' applications, such as tube to tube plate welding and orbital tube welding with tube in the fixed position. Whilst the problems directly associated with this intolerance (of the welding process) are less frequently observed when used manually, difficulties are experienced in fully mechanised welding operations particularly when welding to a relatively rigid approved procedure. Pulsing of the welding current was developed as a technique to achieve greater control of the behaviour of the weld pool. Instead of moving the weld pool in a continuous motion around the joint, welding was conducted intermittently in the form of overlapping spots. This technique, which offers significant advantages over continuous current welding has been exploited in nuclear fabrication for welding those components which demand a high level of weld quality. In this paper, the essential features of this technique are described and, in indicating its advantages, examples have been drawn from recent experiences on the welding of two types of joint for the Advanced Gas Cooled Reactor, a tube sheet and a butt joint in the G Position. (author)

  6. High power components fabrication for 100MeV proton accelerator

    International Nuclear Information System (INIS)

    Cho, Han Sung; Kwon, Hyeok Jung; Jang, Ji Ho; Cho, Yong Sub

    2012-01-01

    Proton Engineering Frontier Project (PEFP) is developing a 100 MeV proton linear accelerator, which consists of ion injector, 3 MeV RFQ, 100 MeV DTL, for basic science research and industrial applications. The design duty factor of the accelerator is as high as 24% up to 20 MeV section and 9% for 100 MeV section. Therefore high heat load is anticipated. The proper cooling of the accelerator components is essential for stable operation of the accelerator. Especially for DTL, many slug tuners are used for frequency tuning and field profile control purpose and active water cooling is required. To control the field profile stability through resonant coupling method, we use several post couplers and these post coupler requires water cooling to remove RF heat load. In addition, we designed and fabricated the vacuum grills with water cooling because wall current should flow through the vacuum grill. The high power RF coupler is a ridge loaded waveguide type iris coupler. The length of the coupler for 100 MeV DTL is reduced to about quarter wavelength from half wavelength one used for 20 MeV DTL. In this paper, a brief introduction and fabrication status of the high power components for the DTL such as slug tuners, post couplers, vacuum grills and high power RF couplers are presented

  7. Concentrating Solar Power Central Receiver Panel Component Fabrication and Testing FINAL REPORT

    Energy Technology Data Exchange (ETDEWEB)

    McDowell, Michael W [Pratt & Whitney Rocketdyne; Miner, Kris [Pratt & Whitney Rocketdyne

    2013-03-30

    The objective of this project is to complete a design of an advanced concentrated solar panel and demonstrate the manufacturability of key components. Then confirm the operation of the key components under prototypic solar flux conditions. This work is an important step in reducing the levelized cost of energy (LCOE) from a central receiver solar power plant. The key technical risk to building larger power towers is building the larger receiver systems. Therefore, this proposed technology project includes the design of an advanced molten salt prototypic sub-scale receiver panel that can be utilized into a large receiver system. Then complete the fabrication and testing of key components of the receive design that will be used to validate the design. This project shall have a significant impact on solar thermal power plant design. Receiver panels of suitable size for utility scale plants are a key element to a solar power tower plant. Many subtle and complex manufacturing processes are involved in producing a reliable, robust receiver panel. Given the substantial size difference between receiver panels manufactured in the past and those needed for large plant designs, the manufacture and demonstration on prototype receiver panel components with representative features of a full-sized panel will be important to improving the build process for commercial success. Given the thermal flux limitations of the test facility, the panel components cannot be rendered full size. Significance changes occurred in the projects technical strategies from project initiation to the accomplishments described herein. The initial strategy was to define cost improvements for the receiver, design and build a scale prototype receiver and test, on sun, with a molten salt heat transport system. DOE had committed to constructing a molten salt heat transport loop to support receiver testing at the top of the NSTTF tower. Because of funding constraints this did not happen. A subsequent plan to

  8. PDSM characterization for fabrication of free-space OXC optical components

    Science.gov (United States)

    Argueta, Victor; Fitzpatrick, Brianna

    2017-11-01

    In 2007 Dr Khine et al published a paper where they presented a technique using thermoplastics and PDMS to create microfluidic patterns1. Their technique involves printing a pattern in a polystyrene sheet using a laser printer. Once the pattern is transfer the polystyrene sheets they are heated to reduce their size. By printing the same pattern of the plastic sheets before heating, it is possible to control the height up to 80 μm and the width as thin as 65 μm1, 2. This technique is attractive to be used in optical fabrication due to its versatility, low cost and fast prototyping. However, in order to fabricate optical systems, we will need to control the refractive index of PDMS to allow design of basic optical components like waveguides, beam splitter, or diffuse reflectors; or more complex structures like interferometers, optical microfluidic lab-on-chip, micro-lens arrays. Several techniques exist to control the refractive index for PDMS either by controlling the curing temperature, the ratio between the base and curing agent, or by curing using UV light3-5. In this paper, we present the changes on refractive index by changing the curing temperature for different base/reaction agent ratios. We then apply these results to fabricate an optical component for a free-space optical cross-connect (OXC). Optical cross-connects are an important network element for constructing the next generation of optical networks, where provisioning (reconfiguration), scalability, and fast restoration will be needed6-8. The main attraction of all-optical switching is that it enables routing of optical data signals without the need for conversion to electrical signals, and therefore, is independent of data rate and data protocols. We have proposed previously9, 11 a new approach for an OXC. Our architecture is a free-space 3-D while still using digital MEMS. Our system is based on the optical White cell12, which consists of three spherical mirrors among which light can circulate. In

  9. SYNTHESIS AND FABRICATION OF MO-W COMPONENTS FOR NEUTRON RESONANCE SPECTROSCOPY TEMPERATURE MEASUREMENT

    International Nuclear Information System (INIS)

    BINGERT, S.; DESCH, P.; TRUJILLO, E.

    1999-01-01

    A Molybdenum-- 182 Tungsten (Mo- 182 W) alloy was specified for an application that would ultimately result in the measurement of temperature and particle velocity during the steady state time following the shock loading of various materials. The 182 W isotope provides a tag for the analysis of neutron resonance line shape from which the temperature may be calculated. The material was specified to have 1.8 atom percent W, with W-rich regions no larger than 1 microm in size. Both the composition and W distribution were critical to the experiment. Another challenge to the processing was the very small quantity of 182 W material available for the synthesis of the alloy. Therefore, limited fabrication routes were available for evaluation. Several synthesis and processing routes were explored to fabricate the required alloy components. First, precipitation of W onto Mo powder using ammonium metatungstate was investigated for powder synthesis followed by uniaxial hot pressing. Second, mechanical alloying (MA) followed by hot isostatic pressing (HIP) and warm forging was attempted. Finally, arc-melting techniques followed by either hot rolling or crushing the alloyed button into powder and consolidation were pursued. The results of the processing routes and characterization of the materials produced will be discussed

  10. Micro-optical components assembly for the fabrication of a miniaturized optoelectronic transducer

    Science.gov (United States)

    Corradi, P.; Ascari, L.; Menciassi, A.; Laschi, C.

    2007-10-01

    This paper describes the fabrication and, in particular, the assembly processes of a miniaturized micro-optical system, to be integrated on a hybrid flexible module, which hosts also electronics and microsensors. The whole module was conceived to be mass-produced in order to be distributed in skin-like structures for robotic tactile applications. Nevertheless, it is generally suitable for sensing applications where the flexibility and the thickness of the sensing network are primary requirements. The micro-optical system works as a part of an optoelectronic transducer where electric signals, generated by tactile MEMS sensors, are computed by a microcontroller that drives the micro-optical system. This consequently generates optical radiation, by means of integrated light emitting diodes (LEDs), to be coupled into optical fibers, which waveguide signals to a CMOS optical sensor. Micro-machining and micro-assembly processes of miniaturized components are critical steps in order to fabricate many of these modules according to the application requirements.

  11. Antibacterial performance of polypropylene nonwoven fabric wound dressing surfaces containing passive and active components

    Science.gov (United States)

    Xin, Zhirong; Du, Shanshan; Zhao, Chunyu; Chen, Hao; Sun, Miao; Yan, Shunjie; Luan, Shifang; Yin, Jinghua

    2016-03-01

    A growing number of wound dressing-related nosocomial infections necessitate the development of novel antibacterial strategies. Herein, polypropylene non-woven fabric (PPNWF) was facilely modified with passive and active antibacterial components, namely photografting polymerization both N-Vinyl-2-pyrrolidone (NVP) and glycidyl methacrylate (GMA) monomers, and the introduction of guanidine polymer through the reaction between active amino groups and epoxy groups. The modified samples were confirmed by attenuated total reflectance Fourier transform infrared spectroscopy (ATR-FTIR), X-ray photoelectron spectroscopy (XPS), respectively. Water contact angle measurement, antibacterial test, platelet and red blood cell adhesion were used to evaluate the hydrophilicity, antibacterial properties and hemocompatibility of the samples. It was found that the antibacterial properties were obviously enhanced, meanwhile significantly suppressing platelet and red blood cell adhesion after the above modification. This PPNWF samples that possess antifouling and antimicrobial properties, have great potential in wound dressing applications.

  12. Investigation of Springback Associated with Composite Material Component Fabrication (MSFC Center Director's Discretionary Fund Final Report, Project 94-09)

    Science.gov (United States)

    Benzie, M. A.

    1998-01-01

    The objective of this research project was to examine processing and design parameters in the fabrication of composite components to obtain a better understanding and attempt to minimize springback associated with composite materials. To accomplish this, both processing and design parameters were included in a Taguchi-designed experiment. Composite angled panels were fabricated, by hand layup techniques, and the fabricated panels were inspected for springback effects. This experiment yielded several significant results. The confirmation experiment validated the reproducibility of the factorial effects, error recognized, and experiment as reliable. The material used in the design of tooling needs to be a major consideration when fabricating composite components, as expected. The factors dealing with resin flow, however, raise several potentially serious material and design questions. These questions must be dealt with up front in order to minimize springback: viscosity of the resin, vacuum bagging of the part for cure, and the curing method selected. These factors directly affect design, material selection, and processing methods.

  13. Antibacterial performance of polypropylene nonwoven fabric wound dressing surfaces containing passive and active components

    Energy Technology Data Exchange (ETDEWEB)

    Xin, Zhirong, E-mail: xinzhirong2012@126.com [School of Chemistry and Chemical Engineering, Yantai University, Yantai 264005 (China); Du, Shanshan; Zhao, Chunyu; Chen, Hao; Sun, Miao [School of Chemistry and Chemical Engineering, Yantai University, Yantai 264005 (China); Yan, Shunjie [State Key Laboratory of Polymer Physics and Chemistry, Changchun Institute of Applied Chemistry, Chinese Academy of Sciences, Changchun 130022 (China); University of Chinese Academy of Sciences, Beijing 100049 (China); Luan, Shifang, E-mail: sfluan@ciac.ac.cn [State Key Laboratory of Polymer Physics and Chemistry, Changchun Institute of Applied Chemistry, Chinese Academy of Sciences, Changchun 130022 (China); Yin, Jinghua [State Key Laboratory of Polymer Physics and Chemistry, Changchun Institute of Applied Chemistry, Chinese Academy of Sciences, Changchun 130022 (China)

    2016-03-01

    Graphical abstract: - Highlights: • PNVP and PHMG components were covalently immobilized on PP{sub NWF} surface. • PP{sub NWF}-g-PNVP-PHMG possessed bacterial adhesion-resistant and bactericidal capabilities. • PP{sub NWF}-g-PNVP-PHMG obviously suppressed platelet and red blood cell adhesion. - Abstract: A growing number of wound dressing-related nosocomial infections necessitate the development of novel antibacterial strategies. Herein, polypropylene non-woven fabric (PP{sub NWF}) was facilely modified with passive and active antibacterial components, namely photografting polymerization both N-Vinyl-2-pyrrolidone (NVP) and glycidyl methacrylate (GMA) monomers, and the introduction of guanidine polymer through the reaction between active amino groups and epoxy groups. The modified samples were confirmed by attenuated total reflectance Fourier transform infrared spectroscopy (ATR-FTIR), X-ray photoelectron spectroscopy (XPS), respectively. Water contact angle measurement, antibacterial test, platelet and red blood cell adhesion were used to evaluate the hydrophilicity, antibacterial properties and hemocompatibility of the samples. It was found that the antibacterial properties were obviously enhanced, meanwhile significantly suppressing platelet and red blood cell adhesion after the above modification. This PP{sub NWF} samples that possess antifouling and antimicrobial properties, have great potential in wound dressing applications.

  14. Antibacterial performance of polypropylene nonwoven fabric wound dressing surfaces containing passive and active components

    International Nuclear Information System (INIS)

    Xin, Zhirong; Du, Shanshan; Zhao, Chunyu; Chen, Hao; Sun, Miao; Yan, Shunjie; Luan, Shifang; Yin, Jinghua

    2016-01-01

    Graphical abstract: - Highlights: • PNVP and PHMG components were covalently immobilized on PP NWF surface. • PP NWF -g-PNVP-PHMG possessed bacterial adhesion-resistant and bactericidal capabilities. • PP NWF -g-PNVP-PHMG obviously suppressed platelet and red blood cell adhesion. - Abstract: A growing number of wound dressing-related nosocomial infections necessitate the development of novel antibacterial strategies. Herein, polypropylene non-woven fabric (PP NWF ) was facilely modified with passive and active antibacterial components, namely photografting polymerization both N-Vinyl-2-pyrrolidone (NVP) and glycidyl methacrylate (GMA) monomers, and the introduction of guanidine polymer through the reaction between active amino groups and epoxy groups. The modified samples were confirmed by attenuated total reflectance Fourier transform infrared spectroscopy (ATR-FTIR), X-ray photoelectron spectroscopy (XPS), respectively. Water contact angle measurement, antibacterial test, platelet and red blood cell adhesion were used to evaluate the hydrophilicity, antibacterial properties and hemocompatibility of the samples. It was found that the antibacterial properties were obviously enhanced, meanwhile significantly suppressing platelet and red blood cell adhesion after the above modification. This PP NWF samples that possess antifouling and antimicrobial properties, have great potential in wound dressing applications.

  15. A study on embedded resistor components fabricated by laser micro-cladding and rapid prototype

    International Nuclear Information System (INIS)

    Li Huiling; Zeng Xiaoyan

    2006-01-01

    With the rapid development of IC and packaging, electronic devices are required to be smaller, to have a high-density integration, to become multifunction and to be of lower cost and high-reliability. Thick-film technology is not able to meet the current developing demands because of its shortcomings, such as the limit of pattern resolution, the severe torsion and delay of high-speed signal transmission. The speed and quality of signal transmission will be improved if embedded resistor components are directly integrated in the multiplayer substrate of multi-chip or laminated module, and high-density integration and reliability are achieved because the short interconnection and the less soldering point. In this paper, a technique named laser micro-cladding and rapid prototype is used to directly fabricate embedded resistor units on the multiplayer ceramic substrate without using a mask and high-temperature sintering, and without trimming resistor, which will simplify processing and decrease cost as well as improving high-speed and reliable performance

  16. Development and fabrication aspects regarding tungsten components for a He-cooled divertor

    International Nuclear Information System (INIS)

    Krauss, W.; Holstein, N.; Konys, J.

    2005-01-01

    Under the EU framework of power plant conceptual study (PPCS), a modular He-cooled divertor concept is investigated, which is projected to remove high heat loads of up to 15 MW/m 2 . This design is based on a modular arrangement of cooling fingers consisting of a tile acting as sacrificial layer, a thimble through-flowed by high pressurized He and special micro-structured components for enhanced heat transfer. The success of this design is strongly correlated to the availability of special tungsten alloys and for the pin/slot option efficient micro-structuring of W or W-1% La 2 O 3 arrays. An evaluation of shaping technologies for array manufacturing under consideration of applicability, degree of development status, expected effectiveness and economy was performed and the most promising methods were tested. Based on the today's knowledge, electrical discharge machining (EDM) and laser etching (LE) allow the shaping of slot arrays; however, an impact on microstructure was detected. Technologies like powder injection moulding (PIM) or electro-chemically assisted machining processes (ECM) need further development and testing to be applied as reliable fabrication processes in structuring of W-alloys

  17. Protective Coatings for Space System Components Fabricated Using Ionic Self Assembled Monolayer Processes

    National Research Council Canada - National Science Library

    Miler, Mike

    1997-01-01

    Self-assembled multilayer thin film fabrication methods offer unique opportunities to incorporate multiple functionalities into coatings for space system materials and structures as well as consumer products...

  18. Stress near geometrically complex strike-slip faults - Application to the San Andreas fault at Cajon Pass, southern California

    Science.gov (United States)

    Saucier, Francois; Humphreys, Eugene; Weldon, Ray, II

    1992-01-01

    A model is presented to rationalize the state of stress near a geometrically complex major strike-slip fault. Slip on such a fault creates residual stresses that, with the occurrence of several slip events, can dominate the stress field near the fault. The model is applied to the San Andreas fault near Cajon Pass. The results are consistent with the geological features, seismicity, the existence of left-lateral stress on the Cleghorn fault, and the in situ stress orientation in the scientific well, found to be sinistral when resolved on a plane parallel to the San Andreas fault. It is suggested that the creation of residual stresses caused by slip on a wiggle San Andreas fault is the dominating process there.

  19. Production management and quality assurance for the fabrication of the In-Vessel Components of the stellarator Wendelstein 7-X

    Energy Technology Data Exchange (ETDEWEB)

    Li, C., E-mail: chuanfei.li@ipp.mpg.de; Boscary, J.; Dekorsy, N.; Junghanns, P.; Mendelevitch, B.; Peacock, A.; Pirsch, H.; Sellmeier, O.; Springer, J.; Stadler, R.; Streibl, B.

    2014-10-15

    Highlights: • Thousand parts for the divertor, first wall, cooling supply and diagnostics as W7-X In-Vessel Components. • Database building including part and assembly data, work and capacity organization, quality assurance documents. • Production management system to organize the fabrication and the associated quality assurance. • Successful use of an efficient and flexible product planning and scheduling tool for W7-X In-Vessel Components. - Abstract: The In-Vessel Components (IVC) of the stellarator Wendelstein 7-X consist of the divertor components and the first wall (FW) with their internal water cooling supply and a set of diagnostics. Due to the significant amount of different components, including many variants, a tool called Production Managing System (PMS) has been developed to organize the fabrication and the associated quality assurance. The PMS works by building a database containing the basic parts and assembly data, manufacturing and quality control plans, and available machine capacity. The creation of this database is based mainly on the parts lists, the manufacturing drawings, and details of the working flow organization. As a consequence of the learning process and technical adjustments during the design and manufacturing phase, the database needed to be permanently updated. Therefore an interface tool to optimize the data preparation has been developed. PMS has been demonstrated to be an efficient tool to support the IVC production activities providing reliable planning estimates, easily adaptable to problems encountered during the fabrication and provided a basis for the integration of quality assurance requirements.

  20. Production management and quality assurance for the fabrication of the In-Vessel Components of the stellarator Wendelstein 7-X

    International Nuclear Information System (INIS)

    Li, C.; Boscary, J.; Dekorsy, N.; Junghanns, P.; Mendelevitch, B.; Peacock, A.; Pirsch, H.; Sellmeier, O.; Springer, J.; Stadler, R.; Streibl, B.

    2014-01-01

    Highlights: • Thousand parts for the divertor, first wall, cooling supply and diagnostics as W7-X In-Vessel Components. • Database building including part and assembly data, work and capacity organization, quality assurance documents. • Production management system to organize the fabrication and the associated quality assurance. • Successful use of an efficient and flexible product planning and scheduling tool for W7-X In-Vessel Components. - Abstract: The In-Vessel Components (IVC) of the stellarator Wendelstein 7-X consist of the divertor components and the first wall (FW) with their internal water cooling supply and a set of diagnostics. Due to the significant amount of different components, including many variants, a tool called Production Managing System (PMS) has been developed to organize the fabrication and the associated quality assurance. The PMS works by building a database containing the basic parts and assembly data, manufacturing and quality control plans, and available machine capacity. The creation of this database is based mainly on the parts lists, the manufacturing drawings, and details of the working flow organization. As a consequence of the learning process and technical adjustments during the design and manufacturing phase, the database needed to be permanently updated. Therefore an interface tool to optimize the data preparation has been developed. PMS has been demonstrated to be an efficient tool to support the IVC production activities providing reliable planning estimates, easily adaptable to problems encountered during the fabrication and provided a basis for the integration of quality assurance requirements

  1. A CNC Sheetmetal Fabrication System for Production of Ships Ventilation Components and Flatwork

    National Research Council Canada - National Science Library

    Galie, Thomas R; Blais, David R

    1981-01-01

    .... By utilizing computer graphics technology and Computer Numeric Control (CNC) machine tools, it is possible to reduce the manhours required for fabrication of ventilation and flatwork by as much as 40 percent...

  2. Process chain for fabrication of anisotropic optical functional surfaces on polymer components

    DEFF Research Database (Denmark)

    Li, Dongya; Zhang, Yang; Regi, Francesco

    2017-01-01

    This paper aims to introduce a process chain for fabrication of anisotropic optical functional surfaces on polymer products. Thesurface features under investigation are composed of micro serrated ridges. The scope was to maximize the visible contrast betweenhorizontally orthogonal textured surfaces...

  3. Application of the methods of sensitivity analysis for optimization of allowances in fabrication of the WWER in-vessel components

    International Nuclear Information System (INIS)

    Mashkovich, V.P.; Safonov, V.I.; Stroganov, A.A.; Tsofin, V.I.

    1987-01-01

    Influence of steel layer thickness decrease , resulting from the existing technological allowances, on fabrication accuracy of in-vessel component shells and on the efficiency of the WWER reactor vessel iron-water shield is considered. Using the WWER-440 reactor as an example it is shown, that the most probable total thickness of steel shell walls is approximately by 0.25 cm smaller, than the nominal thickness. Besides local wall thickness decreases by 0.2-0.5 cm are considered allowable, though such defects may result in local overirradiation of reactor vessel inner surface and in reduction of the vessel service life, respectively. Conclusion is made about the necessity the reconsider and optimaze the existing allowances for fabrication of reactor in-vessel component shells

  4. Inertial confinement fusion target component fabrication and technology development support: Annual report, October 1, 1997--September 30, 1998

    Energy Technology Data Exchange (ETDEWEB)

    Gibson, J. [ed.

    1998-12-01

    During this period, General Atomics (GA) and their partner Schafer Corporation were assigned 17 formal tasks in support of the Inertial Confinement Fusion (ICF) program and its five laboratories. A portion of the effort on these tasks included providing direct ``On-site Support`` at Lawrence Livermore National Laboratory (LLNL), Los Alamos National Laboratory (LANL), and Sandia National Laboratory Albuquerque (SNLA). They fabricated and delivered over 1,200 hohlraum mandrels and numerous other micromachined components to LLNL, LANL, and SNLA. They produced more than 1,300 glass and plastic target capsules for LLNL, LANL, SNLA, and the University of Rochester/Laboratory for Laser Energetics (UR/LLE). They also delivered nearly 2,000 various target foils and films for Naval Research Lab (NRL) and UR/LLE in FY98. This report describes these target fabrication activities and the target fabrication and characterization development activities that made the deliveries possible. During FY98, great progress was made by the GA/Schafer-UR/LLE-LANL team in the design, procurement, installation, and testing of the OMEGA Cryogenic Target System (OCTS) that will field cryogenic targets on OMEGA. The design phase was concluded for all components of the OCTS and all major components were procured and nearly all were fabricated. Many of the components were assembled and tested, and some have been shipped to UR/LLE. The ICF program is anticipating experiments at the OMEGA laser and the National Ignition Facility (NIF) which will require targets containing cryogenic layered D{sub 2} or deuterium-tritium (DT) fuel. They are part of the National Cryogenic Target Program and support experiments at LLNL and LANL to generate and characterize cryogenic layers for these targets. They also contributed cryogenic support and developed concepts for NIF cryogenic targets. This report summarizes and documents the technical progress made on these tasks.

  5. Inertial confinement fusion target component fabrication and technology development support: Annual report, October 1, 1997 - September 30, 1998

    International Nuclear Information System (INIS)

    Gibson, J.

    1998-12-01

    During this period, General Atomics (GA) and their partner Schafer Corporation were assigned 17 formal tasks in support of the Inertial Confinement Fusion (ICF) program and its five laboratories. A portion of the effort on these tasks included providing direct ''On-site Support'' at Lawrence Livermore National Laboratory (LLNL), Los Alamos National Laboratory (LANL), and Sandia National Laboratory Albuquerque (SNLA). They fabricated and delivered over 1,200 hohlraum mandrels and numerous other micromachined components to LLNL, LANL, and SNLA. They produced more than 1,300 glass and plastic target capsules for LLNL, LANL, SNLA, and the University of Rochester/Laboratory for Laser Energetics (UR/LLE). They also delivered nearly 2,000 various target foils and films for Naval Research Lab (NRL) and UR/LLE in FY98. This report describes these target fabrication activities and the target fabrication and characterization development activities that made the deliveries possible. During FY98, great progress was made by the GA/Schafer-UR/LLE-LANL team in the design, procurement, installation, and testing of the OMEGA Cryogenic Target System (OCTS) that will field cryogenic targets on OMEGA. The design phase was concluded for all components of the OCTS and all major components were procured and nearly all were fabricated. Many of the components were assembled and tested, and some have been shipped to UR/LLE. The ICF program is anticipating experiments at the OMEGA laser and the National Ignition Facility (NIF) which will require targets containing cryogenic layered D 2 or deuterium-tritium (DT) fuel. They are part of the National Cryogenic Target Program and support experiments at LLNL and LANL to generate and characterize cryogenic layers for these targets. They also contributed cryogenic support and developed concepts for NIF cryogenic targets. This report summarizes and documents the technical progress made on these tasks

  6. Novel materials, fabrication techniques and algorithms for microwave and THz components, systems and applications

    Science.gov (United States)

    Liang, Min

    This dissertation presents the investigation of several additive manufactured components in RF and THz frequency, as well as the applications of gradient index lens based direction of arrival (DOA) estimation system and broadband electronically beam scanning system. Also, a polymer matrix composite method to achieve artificially controlled effective dielectric properties for 3D printing material is studied. Moreover, the characterization of carbon based nano-materials at microwave and THz frequency, photoconductive antenna array based Terahertz time-domain spectroscopy (THz-TDS) near field imaging system, and a compressive sensing based microwave imaging system is discussed in this dissertation. First, the design, fabrication and characterization of several 3D printed components in microwave and THz frequency are presented. These components include 3D printed broadband Luneburg lens, 3D printed patch antenna, 3D printed multilayer microstrip line structure with vertical transition, THz all-dielectric EMXT waveguide to planar microstrip transition structure and 3D printed dielectric reflectarrays. Second, the additive manufactured 3D Luneburg Lens is employed for DOA estimation application. Using the special property of a Luneburg lens that every point on the surface of the Lens is the focal point of a plane wave incident from the opposite side, 36 detectors are mounted around the surface of the lens to estimate the direction of arrival (DOA) of a microwave signal. The direction finding results using a correlation algorithm show that the averaged error is smaller than 1º for all 360 degree incident angles. Third, a novel broadband electronic scanning system based on Luneburg lens phased array structure is reported. The radiation elements of the phased array are mounted around the surface of a Luneburg lens. By controlling the phase and amplitude of only a few adjacent elements, electronic beam scanning with various radiation patterns can be easily achieved

  7. Aqueous Based Freeze-Form Extrusion Fabrication of Alumina Components (Preprint)

    Science.gov (United States)

    2009-01-01

    and binder-based 3-D Printing (3DP) [ Cima , et al., 2001], Chemical Liquid Deposition (CLD) [He and Zhou, 2000], Selective Laser Sintering (SLS...and Calvert, P., (1998) “Robocasting Provides Moldless Fabrication from Slurry Deposition,” Ceram. Ind., Vol.148, pp. 94-102 20 Cima , M.J

  8. Laser micro-bending for precise micro-fabrication of magnetic disk drive components

    Science.gov (United States)

    Matsushita, Naohisa

    2003-11-01

    Laser Micro-Bending technology attracts attention as one of the laser processing technology promising from now on. It has the feature that does not contact and does not have the spring back that fabrication in high accuracy can be performed. In our company, Laser Micro-Bending technology development is tackled about ten years before, and the laser bending fabrication technology of a sheet metal and ceramic material has so far been established. It has utilized as rapid prototyping of the sheet metal. But, by re-examination of laser oscillation control etc., it finds out that it is the excellent processing method for manufacture of the high precision mechanism parts for magnetic disk drives. This report explains the technology and machines of the roll and pitch adjustment of a magnetic head suspension, and flatting or crowning of the air bearing surface of a magnetic head slider by using Laser Micro-Bending technology.

  9. Nanograined Net-Shaped Fabrication of Rhenium Components by EB-PVD

    International Nuclear Information System (INIS)

    Singh, Jogender; Wolfe, Douglas E.

    2004-01-01

    Cost-effective net-shaped forming components have brought considerable interest into DoD, NASA and DoE. Electron beam physical vapor deposition (EB-PVD) offers flexibility in forming net-shaped components with tailored microstructure and chemistry. High purity rhenium (Re) components including rhenium-coated graphite balls, Re- plates and tubes have been successfully manufactured by EB-PVD. EB-PVD Re components exhibited sub-micron and nano-sized grains with high hardness and strength as compared to CVD. It is estimated that the cost of Re components manufactured by EB-PVD would be less than the current CVD and powder-HIP Technologies

  10. Fabrication of microstructures in aviation components with a femtosecond laser based on PZT scanning

    International Nuclear Information System (INIS)

    Yang, Xiaojun; Zhao, Wei; Li, Ming; Yang, Yong; Cheng, Guanghua; Zhao, Hualong; Li, Peng; Zhang, Huixing

    2013-01-01

    Thermal defects and low precision are the main disadvantages of fabricating micro-holes, irregular holes, and micro-slots in thermostable aviation materials. We demonstrate a manufacturing method employing a femtosecond laser and piezoelectric ceramic (PZT). The production process parameters were optimized according to the metallographic and dimensional accuracy of the microstructure, which was measured by phase-contrast microscopy and scanning electron microscopy. The limitations in a conventional aeroengine, such as in the recast layer, recrystallization, and micro-cracks, which degrade the performance and service life, were resolved with a simple, controllable, and commercial method. (paper)

  11. Design and fabrication of stainless steel components for long life of spent fuel reprocessing plants

    International Nuclear Information System (INIS)

    Natarajan, R.; Ramkumar, P.; Sundararaman, V.; Kamachi Mudali, U.; Baldev Raj; Shanmugam, K.

    2010-01-01

    Reprocessing of spent nuclear fuels based on the PUREX process is the proven process with many commercial plants operating satisfactorily worldwide. The process medium being nitric acid, austenitic stainless steel is the material of construction as it is the best commercially available material for meeting the conditions in the reprocessing plants. Because of the high radiation fields, contact maintenance of equipment and systems of these plants are very time consuming and costly unlike other chemical process plants. Though the plants constructed in the early years required extensive shut downs for replacement of equipment and systems within the first fifteen years of operation itself, development in the field of stainless steel metallurgy and fabrication techniques have made it possible to design the present day plants for an operating life period of forty years. A review of the operational experience of the PUREX process based aqueous reprocessing plants has been made in this paper and reveals that life limiting failures of equipment and systems are mainly due to corrosion while a few are due to stresses. Presently there are no standards for design specification of materials and fabrication of reprocessing plants like the nuclear power plants, where well laid down ASTM and ASME codes and standards are available which are based on the large scale operational feedbacks on pressure vessels for conventional and nuclear industries. (author)

  12. Near Net Shape Fabrication Technology for Shape Memory Alloy Components Project

    Data.gov (United States)

    National Aeronautics and Space Administration — This STTR Phase I effort proposes to develop an innovative, affordable processing route for larger-sized shape memory alloy (SMA) components. Despite significant...

  13. Near Net Shape Fabrication Technology for Shape Memory Alloy Components, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — This STTR Phase I effort proposes to develop an innovative, affordable processing route for larger-sized shape memory alloy (SMA) components. Despite significant...

  14. Fabrication of optical fiber micro(and nano)-optical and photonic devices and components, using computer controlled spark thermo-pulling system

    International Nuclear Information System (INIS)

    Fatemi, H.; Mosleh, A.; Pashmkar, M.; Khaksar Kalati, A.

    2007-01-01

    Fabrication of optical fiber Micro (and Nano)-Optical component and devices, as well as, those applicable for photonic purposes are described. It is to demonstrate the practical capabilities and characterization of the previously reported Computer controlled spark thermo-pulling fabrication system.

  15. Fabricating Superior NiAl Bronze Components through Wire Arc Additive Manufacturing

    Directory of Open Access Journals (Sweden)

    Donghong Ding

    2016-08-01

    Full Text Available Cast nickel aluminum bronze (NAB alloy is widely used for large engineering components in marine applications due to its excellent mechanical properties and corrosion resistance. Casting porosity, as well as coarse microstructure, however, are accompanied by a decrease in mechanical properties of cast NAB components. Although heat treatment, friction stir processing, and fusion welding were implemented to eliminate porosity, improve mechanical properties, and refine the microstructure of as-cast metal, their applications are limited to either surface modification or component repair. Instead of traditional casting techniques, this study focuses on developing NAB components using recently expanded wire arc additive manufacturing (WAAM. Consumable welding wire is melted and deposited layer-by-layer on substrates producing near-net shaped NAB components. Additively-manufactured NAB components without post-processing are fully dense, and exhibit fine microstructure, as well as comparable mechanical properties, to as-cast NAB alloy. The effects of heat input from the welding process and post-weld-heat-treatment (PWHT are shown to give uniform NAB alloys with superior mechanical properties revealing potential marine applications of the WAAM technique in NAB production.

  16. Inertial confinement fusion target component fabrication and technology development support: Annual report, October 1, 1995--September 30, 1996

    International Nuclear Information System (INIS)

    Hoppe, M.

    1997-02-01

    On December 30, 1990, the U.S. Department of Energy entered into a contract with General Atomics (GA) to be the Inertial Confinement Fusion (ICF) Target Component Fabrication and Technology Development Support contractor. In September 1995 this contract ended and a second contract was issued for us to continue this ICF target support work. This report documents the technical activities of the period October 1, 1995 through September 30, 1996. During this period, GA and our partners WJ Schafer Associates (WJSA) and Soane Technologies, Inc. (STI) were assigned 14 formal tasks in support of the Inertial Confinement Fusion program and its five laboratories. A portion of the effort on these tasks included providing direct open-quotes Onsite Supportclose quotes at Lawrence Livermore National Laboratory (LLNL), Los Alamos National Laboratory (LANL), and Sandia National Laboratory Albuquerque (SNLA). We fabricated and delivered over 800 gold-plated hohlraum mandrels to LLNL, LANL and SNLA. We produced nearly 1,200 glass and plastic target capsules for LLNL, LANL, SNLA and University of Rochester/Laboratory for Laser Energetics (UR/LLE). We also delivered over 100 flat foil targets for Naval Research Lab (NRL) and SNLA in FY96. This report describes these target fabrication activities and the target fabrication and characterization development activities that made the deliveries possible. The ICF program is anticipating experiments at the OMEGA laser and the National Ignition Facility (NIF) which will require capsules containing cryogenic layered D 2 or deuterium-tritium (DT) fuel. We are part of the National Cryogenic Target Program to create and demonstrate viable ways to generate and characterize cryogenic layers. Substantial progress has been made on ways to both create and characterize viable layers. During FY96, significant progress was made in the design of the OMEGA Cryogenic Target System that will field cryogenic targets on OMEGA

  17. Fabrication, Quality Assurance, and Quality Control for PROSPECT Detector Component Production

    Science.gov (United States)

    Gustafson, Ian; Prospect (The Precision Reactor Oscillation; Spectrum Experiment) Collaboration

    2017-09-01

    The Precision Reactor Oscillation and Spectrum Experiment (PROSPECT) is an electron antineutrino (νe) detector intended to make a precision measurement of the 235U neutrino spectrum and to search for the possible existence of sterile neutrinos with a mass splitting of Δm2 on the order of 1 eV2 . As a short baseline detector, PROSPECT will be located less than 10 meters from the High Flux Isotope Reactor at Oak Ridge National Laboratory. As PROSPECT intends to search for baseline-dependent oscillations, physical segmentation is needed to better measure the interaction position. PROSPECT will therefore be a segmented detector in two dimensions, thereby improving position measurements. PROSPECT will be segmented into 154 (11×14) 1.2-meter long rectangular tubes, using optical separators. Each separator will consist of a carbon fiber core, laminated with optical reflector (to increase light collection) and Teflon (to ensure compatibility with the scintillator). These optical separators will be held in place via strings of 3D printed PLA rods called `pinwheels.' This poster discusses the fabrication and quality assurance (QA) procedures used in the production of both the PROSPECT optical separators and pinwheels. For the PROSPECT collaboration.

  18. Fabrication of 3D fine scale PZT components by ink-jet prototyping process

    Science.gov (United States)

    Noguera, R.; Dossou-Yovo, C.; Lejeune, M.; Chartier, T.

    2005-09-01

    Different investigations have been carried out to optimize an ink-jet printing technique, devoted to the fabrication of 3D fine scale PZT parts, by adjustment of the fluid properties of the ceramic suspensions and by controlling the ejection and impact phenomena. A 10 vol% PZT loaded suspension characterized by a Newtonian behavior, corresponding to a viscosity of 10mPa.s and to a ratio Re/We1/2 of 5.98 has been selected. The ejection and impact phenomena strongly depend on the driving parameters of the printing head, in particular the formation of the droplet, with satellite or not, as well as its velocity and volume which are function of the pulse amplitude. Moreover, the conditions of ejection (droplet velocity and volume) control the characteristics of the deposit (definition, spreading, thickness uniformity). Sintered PZT pillar array has been achieved by ink-jet printing with a definition equal to 50μm. These structures could be very useful to improve the performances of 1-3 ceramic polymer composites for imaging probes or more generally for ultrasonic transducers and also of micro-deformable mirrors for optical adaptive systems.

  19. Net Shaped Component Fabrication of Refractory Metal Alloys using Vacuum Plasma Spraying

    Science.gov (United States)

    Sen, S.; ODell, S.; Gorti, S.; Litchford, R.

    2006-01-01

    The vacuum plasma spraying (VPS) technique was employed to produce dense and net shaped components of a new tungsten-rhenium (W-Re) refractory metal alloy. The fine grain size obtained using this technique enhanced the mechanical properties of the alloy at elevated temperatures. The alloy development also included incorporation of thermodynamically stable dispersion phases to pin down grain boundaries at elevated temperatures and thereby circumventing the inherent problem of recrystallization of refractory alloys at elevated temperatures. Requirements for such alloys as related to high temperature space propulsion components will be discussed. Grain size distribution as a function of cooling rate and dispersion phase loading will be presented. Mechanical testing and grain growth results as a function of temperature will also be discussed.

  20. The status of ceramic turbine component fabrication and quality assurance relevant to automotive turbine needs

    Energy Technology Data Exchange (ETDEWEB)

    Richerson, D.W.

    2000-02-01

    This report documents a study funded by the U.S. Department of Energy (DOE) Office of Transportation Technologies (OTT) with guidance from the Ceramics Division of the United States Automotive Materials Partnership (USAMP). DOE and the automotive companies have funded extensive development of ceramic materials for automotive gas turbine components, the most recent effort being under the Partnership for a New Generation of Vehicles (PNGV) program.

  1. Report on fabrication of pin components for fuel fabrication in FUJI project (Co-operation in the research and development of advanced sphere-pac fuel among PSI, JNC, and NRG)

    International Nuclear Information System (INIS)

    Suzuki, Masahiro; Hinai, Hiroshi; Shigetome, Yoshiaki; Kono, Shusaku; Matsuzaki, Masaaki

    2003-03-01

    Japan Nuclear Cycle Development Institute (JNC) has conducted the co-operation concerning vibro-packed fuels with Paul Scherrer Institut (PSI) in Switzerland and Nuclear Research and consultancy Group (NRG) in the Netherlands. The project 'Research and Development of advanced Sphere-pac Fuel' is called FUJI (FUel irradiations for JNC and PSI) Project. In this project, three types of fuels that are sphere-pac fuels, vipac fuels, and pellet fuels will be irradiated in the High Flux Reactor (HFR) to compare their performance. Based on the drawing which has been agreed among three parties, fabrication of the pin components and welding of the upper and lower connection end plugs were performed in accordance with ISO9001 in JNC. This report describes data of the fabricated pin components, results of welding qualification tests, and quality assurance of the welded components. The fabrication of pin components was successfully completed and they were delivered to PSI in October 2002. (author)

  2. A database of wavefront measurements for laser system modeling, optical component development and fabrication process qualification

    International Nuclear Information System (INIS)

    Wolfe, C.R.; Lawson, J.K.; Aikens, D.M.; English, R.E.

    1995-01-01

    In the second half of the 1990's, LLNL and others anticipate designing and beginning construction of the National Ignition Facility (NIF). The NIF will be capable of producing the worlds first laboratory scale fusion ignition and bum reaction by imploding a small target. The NIF will utilize approximately 192 simultaneous laser beams for this purpose. The laser will be capable of producing a shaped energy pulse of at least 1.8 million joules (MJ) with peak power of at least 500 trillion watts (TV). In total, the facility will require more than 7,000 large optical components. The performance of a high power laser of this kind can be seriously degraded by the presence of low amplitude, periodic modulations in the surface and transmitted wavefronts of the optics used. At high peak power, these phase modulations can convert into large intensity modulations by non-linear optical processes. This in turn can lead to loss in energy on target via many well known mechanisms. In some cases laser damage to the optics downstream of the source of the phase modulation can occur. The database described here contains wavefront phase maps of early prototype optical components for the NIF. It has only recently become possible to map the wavefront of these large aperture components with high spatial resolution. Modem large aperture static fringe and phase shifting interferometers equipped with large area solid state detectors have made this possible. In a series of measurements with these instruments, wide spatial bandwidth can be detected in the wavefront

  3. Inertial confinement fusion target component fabrication and technology development support. Annual report, October 1, 1996--September 30, 1997

    Energy Technology Data Exchange (ETDEWEB)

    Gibson, J. [ed.

    1998-03-01

    This report documents the technical activities of the period October 1, 1996 through September 30, 1997. During this period, GA and their partner Schafer Corporation were assigned 13 formal tasks in support of the ICF program and its five laboratories. A portion of the effort on these tasks included providing direct {open_quotes}Onsite Support{close_quotes} at Lawrence Livermore National Laboratory (LLNL), Los Alamos National Laboratory (LANL), and Sandia National Laboratory Albuquerque (SNLA). Over 700 gold-plated hohlraum mandrels were fabricated and delivered to LLNL, LANL and SNLA. More than 1600 glass and plastic target capsules were produced for LLNL, LANL, SNLA and University of Rochester/Laboratory for Laser Energetics (UR/LLE). Nearly 2000 various target foils and films were delivered for Naval Research Lab (NRL) and UR/LLE in FY97. This report describes these target fabrication activities and the target fabrication and characterization development activities that made the deliveries possible. The ICF program is anticipating experiments at the OMEGA laser and the National Ignition Facility (NIF) which will require targets containing cryogenic layered D{sub 2} or deuterium-tritium (DT) fuel. This project is part of the National Cryogenic Target Program and support experiments at LLNL and LANL to generate and characterize cryogenic layers for these targets. During FY97, significant progress was made in the design and component testing of the OMEGA Cryogenic Target System that will field cryogenic targets on OMEGA. This included major design changes, reduction in equipment, and process simplifications. This report summarizes and documents the technical progress made on these tasks.

  4. Functionalisation of Ti6Al4V components fabricated using selective laser melting with a bioactive compound

    Energy Technology Data Exchange (ETDEWEB)

    Vaithilingam, Jayasheelan [Additive Manufacturing and 3D Printing Research Group, School of Engineering, The University of Nottingham, Nottingham NG7 2RD (United Kingdom); Kilsby, Samuel [Department of Chemistry, Loughborough University, Loughborough LE11 3TU (United Kingdom); Goodridge, Ruth D., E-mail: Ruth.Goodridge@nottingham.ac.uk [Additive Manufacturing and 3D Printing Research Group, School of Engineering, The University of Nottingham, Nottingham NG7 2RD (United Kingdom); Christie, Steven D.R. [Department of Chemistry, Loughborough University, Loughborough LE11 3TU (United Kingdom); Edmondson, Steve [School of Materials, The University of Manchester, Manchester M13 9PL (United Kingdom); Hague, Richard J.M. [Additive Manufacturing and 3D Printing Research Group, School of Engineering, The University of Nottingham, Nottingham NG7 2RD (United Kingdom)

    2015-01-01

    Surface modification of an implant with a biomolecule is used to improve its biocompatibility and to reduce post-implant complications. In this study, a novel approach has been used to functionalise phosphonic acid monolayers with a drug. Ti6Al4V components fabricated using selective laser melting (SLM) were functionalised with Paracetamol (a pharmaceutically relevant biomolecule) using phosphonic acid based self-assembled monolayers (SAMs). The attachment, stability of the monolayers on the SLM fabricated surface and functionalisation of SAMs with Paracetamol were studied using X-ray photoelectron spectroscopy (XPS) and surface wettability measurements. The obtained results confirmed that SAMs were stable on the Ti6Al4V surface for over four weeks and then began to desorb from the surface. The reaction used to functionalise the phosphonic acid monolayers with Paracetamol was noted to be successful. Thus, the proposed method has the potential to immobilise drugs/proteins to SAM coated surfaces and improve their biocompatibility and reduce post-implant complications. - Graphical abstract: A significant change in the contact angle confirming the immobilisation of Paracetamol. (a) Before self-assembled monolayer (SAM) attachment, (b) after SAM attachment and (c) after the immobilisation of Paracetamol to the SAMs. - Highlights: • Ti6Al4V parts were fabricated using selective laser melting (SLM). • Monolayers used to modify the SLM surface were stable for over 28 days (in-vitro). • Surface roughness did not have a significant impact on the monolayer stability. • Paracetamol was successfully immobilised to the adsorbed monolayers. • Caution required before selecting Paracetamol as a model drug.

  5. Inertial confinement fusion target component fabrication and technology development support. Annual report, October 1, 1996 - September 30, 1997

    International Nuclear Information System (INIS)

    Gibson, J.

    1998-03-01

    This report documents the technical activities of the period October 1, 1996 through September 30, 1997. During this period, GA and their partner Schafer Corporation were assigned 13 formal tasks in support of the ICF program and its five laboratories. A portion of the effort on these tasks included providing direct open-quotes Onsite Supportclose quotes at Lawrence Livermore National Laboratory (LLNL), Los Alamos National Laboratory (LANL), and Sandia National Laboratory Albuquerque (SNLA). Over 700 gold-plated hohlraum mandrels were fabricated and delivered to LLNL, LANL and SNLA. More than 1600 glass and plastic target capsules were produced for LLNL, LANL, SNLA and University of Rochester/Laboratory for Laser Energetics (UR/LLE). Nearly 2000 various target foils and films were delivered for Naval Research Lab (NRL) and UR/LLE in FY97. This report describes these target fabrication activities and the target fabrication and characterization development activities that made the deliveries possible. The ICF program is anticipating experiments at the OMEGA laser and the National Ignition Facility (NIF) which will require targets containing cryogenic layered D 2 or deuterium-tritium (DT) fuel. This project is part of the National Cryogenic Target Program and support experiments at LLNL and LANL to generate and characterize cryogenic layers for these targets. During FY97, significant progress was made in the design and component testing of the OMEGA Cryogenic Target System that will field cryogenic targets on OMEGA. This included major design changes, reduction in equipment, and process simplifications. This report summarizes and documents the technical progress made on these tasks

  6. Fabrication and Characterizations of Materials and Components for Intermediate Temperature Fuel Cells and Water Electrolysers

    DEFF Research Database (Denmark)

    Jensen, Annemette Hindhede; Prag, Carsten Brorson; Li, Qingfeng

    The worldwide development of fuel cells and electrolysers has so far almost exclusively addressed either the low temperature window (20-200 °C) or the high temperature window (600-1000 °C). This work concerns the development of key materials and components of a new generation of fuel cells...... and electrolysers for operation in the intermediate temperature range from 200 to 400 °C. The intermediate temperature interval is of importance for the use of renewable fuels. Furthermore electrode kinetics is significantly enhanced compared to when operating at low temperature. Thus non-noble metal catalysts...... might be used. One of the key materials in the fuel cell and electrolyser systems is the electrolyte. Proton conducting materials such as cesium hydrogen phosphates, zirconium hydrogen phosphates and tin pyrophosphates have been investigated by others and have shown interesting potential....

  7. Functionalisation of Ti6Al4V components fabricated using selective laser melting with a bioactive compound.

    Science.gov (United States)

    Vaithilingam, Jayasheelan; Kilsby, Samuel; Goodridge, Ruth D; Christie, Steven D R; Edmondson, Steve; Hague, Richard J M

    2015-01-01

    Surface modification of an implant with a biomolecule is used to improve its biocompatibility and to reduce post-implant complications. In this study, a novel approach has been used to functionalise phosphonic acid monolayers with a drug. Ti6Al4V components fabricated using selective laser melting (SLM) were functionalised with Paracetamol (a pharmaceutically relevant biomolecule) using phosphonic acid based self-assembled monolayers (SAMs). The attachment, stability of the monolayers on the SLM fabricated surface and functionalisation of SAMs with Paracetamol were studied using X-ray photoelectron spectroscopy (XPS) and surface wettability measurements. The obtained results confirmed that SAMs were stable on the Ti6Al4V surface for over four weeks and then began to desorb from the surface. The reaction used to functionalise the phosphonic acid monolayers with Paracetamol was noted to be successful. Thus, the proposed method has the potential to immobilise drugs/proteins to SAM coated surfaces and improve their biocompatibility and reduce post-implant complications. Copyright © 2014. Published by Elsevier B.V.

  8. Inertial confinement fusion target component fabrication and technology development support: Annual report, October 1, 1993--September 30, 1994

    International Nuclear Information System (INIS)

    Hoppe, M.

    1995-04-01

    On December 30, 1990, the US Department of Energy entered into a contract with General Atomics (GA) to be the Inertial Confinement Fusion (ICF) Target Component Fabrication and Technology Development Support contractor. During the period, GA was assigned 17 tasks in support of the Inertial Confinement Fusion program and its laboratories. This year they achieved full production capabilities for the micromachining, dimensional characterization and gold plating of hohlraums. They fabricated and delivered 726 gold-plated mandrels of 27 different types to LLNL and 48 gold-plated mandrels of two different types to LANL. They achieved full production capabilities in composite capsule production ad delivered in excess of 240 composite capsules. They continuously work to improve performance and capabilities. They were also directed to dismantle, remove, and disposition all equipment at the previous contractor (KMSF) that had radioactive contamination levels low enough that they could be exposed to the general public without radiological constraints. GA was also directed to receive and store the tritium fill equipment. They assisted LANL in the development of techniques for characterization of opaque targets. They developed deuterated and UV-opaque polymers for use by the University of Rochester's Laboratory for Laser Energetics (UR/LLE) and devised a triple-orifice droplet generator to demonstrate the controlled-mass nature of the microencapsulation process. The ICF program is anticipating experiments at NIF and the Omega Upgrade. Both facilities will require capsules containing layered D 2 or D-T fuel. They continued engineering and assembly of equipment for a cryogenic target handling system for UR/LLE that will fill, transport, layer, and characterize targets filled with cryogenic deuterium or deuterium-tritium fuel, and insert these cryogenic targets into the OMEGA Upgrade target chamber for laser implosion experiments

  9. Inertial confinement fusion target component fabrication and technology development support. Annual report, October 1, 1994--September 30, 1995

    Energy Technology Data Exchange (ETDEWEB)

    Hoppe, M. [ed.

    1996-05-01

    On December 30, 1990, the US Department of Energy entered into a contract with General Atomics (GA) to be the Inertial Confinement Fusion (ICF) Target Component Fabrication and Technology Development Support contractor. This report documents the technical activities of the period October 1, 1994 through September 30, 1995. During this period, GA was assigned 15 tasks in support of the Inertial Confinement Fusion program and its laboratories. A portion of the effort on these tasks included providing direct ``Onsite Support`` at Lawrence Livermore National Laboratory (LLNL), Los Alamos National Laboratory (LANL), and Sandia National Laboratory Albuquerque (SNLA). The ICF program is anticipating experiments at the National Ignition Facility (NIF) and the OMEGA Upgrade. Both facilities will require capsules containing layered D{sub 2} or deuterium-tritium (D-T) fuel. The authors are part of the National Cryogenic Target Program to create and demonstrate viable ways to generate and characterize cryogenic layers. Progress has been made on ways to both create viable layers and to characterize them. They continued engineering, assembly and testing of equipment for a cryogenic target handling system for University of Rochester`s Laboratory for Laser Energetics (UR/LLE) that will fill, transport, layer, and characterize targets filled with cryogenic fuel, and insert these cryogenic targets into the OMEGA Upgrade target chamber for laser implosion experiments. This report summarizes and documents the technical progress made on these tasks.

  10. Inertial confinement fusion target component fabrication and technology development support. Annual report, October 1, 1994--September 30, 1995

    International Nuclear Information System (INIS)

    Hoppe, M.

    1996-05-01

    On December 30, 1990, the US Department of Energy entered into a contract with General Atomics (GA) to be the Inertial Confinement Fusion (ICF) Target Component Fabrication and Technology Development Support contractor. This report documents the technical activities of the period October 1, 1994 through September 30, 1995. During this period, GA was assigned 15 tasks in support of the Inertial Confinement Fusion program and its laboratories. A portion of the effort on these tasks included providing direct ''Onsite Support'' at Lawrence Livermore National Laboratory (LLNL), Los Alamos National Laboratory (LANL), and Sandia National Laboratory Albuquerque (SNLA). The ICF program is anticipating experiments at the National Ignition Facility (NIF) and the OMEGA Upgrade. Both facilities will require capsules containing layered D 2 or deuterium-tritium (D-T) fuel. The authors are part of the National Cryogenic Target Program to create and demonstrate viable ways to generate and characterize cryogenic layers. Progress has been made on ways to both create viable layers and to characterize them. They continued engineering, assembly and testing of equipment for a cryogenic target handling system for University of Rochester's Laboratory for Laser Energetics (UR/LLE) that will fill, transport, layer, and characterize targets filled with cryogenic fuel, and insert these cryogenic targets into the OMEGA Upgrade target chamber for laser implosion experiments. This report summarizes and documents the technical progress made on these tasks

  11. Surface chemistry of Ti6Al4V components fabricated using selective laser melting for biomedical applications

    Energy Technology Data Exchange (ETDEWEB)

    Vaithilingam, Jayasheelan, E-mail: Jayasheelan.Vaithilingam@nottingham.ac.uk [Additive Manufacturing and 3D Printing Research Group, EPSRC Centre for Innovative Manufacturing in Additive Manufacturing, School of Engineering, The University of Nottingham, Nottingham NG7 2RD (United Kingdom); Prina, Elisabetta [School of Pharmacy, Centre for Biomolecular Sciences, The University of Nottingham, Nottingham NG7 2RD (United Kingdom); Goodridge, Ruth D.; Hague, Richard J.M. [Additive Manufacturing and 3D Printing Research Group, EPSRC Centre for Innovative Manufacturing in Additive Manufacturing, School of Engineering, The University of Nottingham, Nottingham NG7 2RD (United Kingdom); Edmondson, Steve [School of Materials, The University of Manchester, Manchester M13 9PL (United Kingdom); Rose, Felicity R.A.J. [School of Pharmacy, Centre for Biomolecular Sciences, The University of Nottingham, Nottingham NG7 2RD (United Kingdom); Christie, Steven D.R. [Department of Chemistry, Loughborough University, Loughborough LE11 3TU (United Kingdom)

    2016-10-01

    Selective laser melting (SLM) has previously been shown to be a viable method for fabricating biomedical implants; however, the surface chemistry of SLM fabricated parts is poorly understood. In this study, X-ray photoelectron spectroscopy (XPS) was used to determine the surface chemistries of (a) SLM as-fabricated (SLM-AF) Ti6Al4V and (b) SLM fabricated and mechanically polished (SLM-MP) Ti6Al4V samples and compared with (c) traditionally manufactured (forged) and mechanically polished Ti6Al4V samples. The SLM–AF surface was observed to be porous with an average surface roughness (Ra) of 17.6 ± 3.7 μm. The surface chemistry of the SLM-AF was significantly different to the FGD-MP surface with respect to elemental distribution and their existence on the outermost surface. Sintered particles on the SLM-AF surface were observed to affect depth profiling of the sample due to a shadowing effect during argon ion sputtering. Surface heterogeneity was observed for all three surfaces; however, vanadium was witnessed only on the mechanically polished (SLM-MP and FGD-MP) surfaces. The direct and indirect 3T3 cell cytotoxicity studies revealed that the cells were viable on the SLM fabricated Ti6Al4V parts. The varied surface chemistry of the SLM-AF and SLM-MP did not influence the cell behaviour. - Highlights: • Surface chemistry of selective laser melted (SLM) Ti6Al4V parts was compared with conventionally forged Ti6Al4V parts. • The surface elemental compositions of the SLM as-fabricated surfaces were significantly different to the forged surface. • Surface oxide-layer of the SLM as-fabricated was thicker than the polished SLM surfaces and the forged Ti6Al4V surfaces.

  12. Surface chemistry of Ti6Al4V components fabricated using selective laser melting for biomedical applications.

    Science.gov (United States)

    Vaithilingam, Jayasheelan; Prina, Elisabetta; Goodridge, Ruth D; Hague, Richard J M; Edmondson, Steve; Rose, Felicity R A J; Christie, Steven D R

    2016-10-01

    Selective laser melting (SLM) has previously been shown to be a viable method for fabricating biomedical implants; however, the surface chemistry of SLM fabricated parts is poorly understood. In this study, X-ray photoelectron spectroscopy (XPS) was used to determine the surface chemistries of (a) SLM as-fabricated (SLM-AF) Ti6Al4V and (b) SLM fabricated and mechanically polished (SLM-MP) Ti6Al4V samples and compared with (c) traditionally manufactured (forged) and mechanically polished Ti6Al4V samples. The SLM-AF surface was observed to be porous with an average surface roughness (Ra) of 17.6±3.7μm. The surface chemistry of the SLM-AF was significantly different to the FGD-MP surface with respect to elemental distribution and their existence on the outermost surface. Sintered particles on the SLM-AF surface were observed to affect depth profiling of the sample due to a shadowing effect during argon ion sputtering. Surface heterogeneity was observed for all three surfaces; however, vanadium was witnessed only on the mechanically polished (SLM-MP and FGD-MP) surfaces. The direct and indirect 3T3 cell cytotoxicity studies revealed that the cells were viable on the SLM fabricated Ti6Al4V parts. The varied surface chemistry of the SLM-AF and SLM-MP did not influence the cell behaviour. Copyright © 2016 The Authors. Published by Elsevier B.V. All rights reserved.

  13. Architectural Geometry and Fabrication-Aware Design

    KAUST Repository

    Pottmann, Helmut

    2013-04-27

    Freeform shapes and structures with a high geometric complexity play an increasingly important role in contemporary architecture. While digital models are easily created, the actual fabrication and construction remains a challenge. This is the source of numerous research problems many of which fall into the area of Geometric Computing and form part of a recently emerging research area, called "Architectural Geometry". The present paper provides a short survey of research in Architectural Geometry and shows how this field moves towards a new direction in Geometric Modeling which aims at combining shape design with important aspects of function and fabrication. © 2013 Kim Williams Books, Turin.

  14. 3D-printed fusion components concepts and validation for the UST_2 stellarator

    International Nuclear Information System (INIS)

    Queral, V.

    2015-01-01

    Highlights: • A fabrication method for fusion components is developed and validated. • Synergies obtained from additive manufacturing and non-metal casting. • 3D-printed polyamide hollow truss structure and casting of acrylic resin tested. • UST_ 2 stellarator coil frame fabricated to validate the method performance. - Abstract: The geometric complexity and high accuracy simultaneously required in magnetic fusion devices, particularly stellarators and tokamaks, hampers the production of fusion components and devices. Rapid manufacturing construction methods, particularly enhanced for fusion, may contribute to a faster cycle and lower cost production of certain components for tokamaks and stellarators. Casting, cutting, forming, welding and mechanising are conventional production techniques for major fusion components, i.e. coil casings, coil frames, vacuum vessels and blankets. Synergies may emerge by combination of additive manufacturing (3D printing) with conventional manufacturing methods. 3D printing combined with resin moulding is tested by construction of the coil frame and the vacuum vessel of a small stellarator, UST_2. Satisfactory coil frames have been obtained by moulding acrylic resin in a special 3D printed polyamide hollow three-dimensional structure. The conceptual engineering design, construction process and validation of the components are described. The presented manufacturing method might contribute to advance the future 3D printing of larger metallic components for fusion.

  15. Inertial confinement fusion target component fabrication and technology development support. Annual report 10/1/98 through 9/30/99

    International Nuclear Information System (INIS)

    Gibson, Jane

    1999-01-01

    General Atomics (GA) has served as the Inertial Confinement Fusion (ICF) Target Component Fabrication and Technology Development Support contractor for the U.S. Department of Energy since December 30, 1990. This report documents the technical activities of the period October 1, 1998 through September 30, 1999. During this period, GA and our partner Schafer Corporation were assigned 17 formal tasks in support of the ICF program and its five laboratories. A portion of the effort on these tasks included providing direct ''Onsite Support'' at Lawrence Livermore National Laboratory (LLNL), Los Alamos National Laboratory (LANL), and Sandia National Laboratory (SNL). We fabricated and delivered over 1790 hohlraum mandrels and numerous other micromachined components to LLNL, LANL, and SNL. We produced more than 1380 glass and plastic target capsules over a wide range of sizes and designs (plus over 300 near target-quality capsules) for LLNL, LANL, SNL, and University of Rochester/Laboratory for Laser Energetic (UR/LLE). We also delivered various target foils and films for Naval Research Lab (NRL) and UWLLE in FY99. We fabricated a device to polish NIF-sized beryllium shells and prepared a laboratory for the safe operation of beryllium polishing activities. This report describes these target fabrication activities and the target fabrication and characterization development activities that made the deliveries possible. During FY99, the GA/Schafer portion of the GA/Schafer-UR/LLE-LANL team effort for design, procurement, installation, and testing of the OMEGA Cryogenic Target System (OCTS) that will field cryogenic targets on OMEGA was completed. All components of the OCTS were procured, fabricated, assembled, tested, and shipped to UR/LLE. Only minor documentation tasks remain to be done in FY00. The ICF program is anticipating experiments at the OMEGA laser and the National Ignition Facility (NIF) which will require targets containing cryogenic layered D2 or deuterium

  16. Fabrication of nano-scaled polymer-derived SiAlCN ceramic components using focused ion beam

    Science.gov (United States)

    Tian, Ye; Shao, Gang; Wang, Xingwei; An, Linan

    2013-09-01

    Fully dense polymer-derived amorphous silicoaluminum carbonitride (SiAlCN) ceramics were synthesized from polysilazane as preceramic precursors followed by a thermal decomposition process. The nanofabrication of amorphous SiAlCN ceramics was implemented with a focused ion beam (FIB). FIB conditions such as the milling rate, the beam current, and the number of passes were considered. It was found that nanopatterns with a feature size of less than 100 nm could be fabricated onto polymer-derived ceramics (PDCs) precisely and quickly. Specific nanostructures of thin walls, nozzle, and gear have been fabricated as demonstrations, indicating that the FIB technique was a promising method to realize nanostructures on PDCs, especially for microelectromechanical system and micro/nano-sensor applications.

  17. Fabrication of nano-scaled polymer-derived SiAlCN ceramic components using focused ion beam

    International Nuclear Information System (INIS)

    Tian, Ye; Wang, Xingwei; Shao, Gang; An, Linan

    2013-01-01

    Fully dense polymer-derived amorphous silicoaluminum carbonitride (SiAlCN) ceramics were synthesized from polysilazane as preceramic precursors followed by a thermal decomposition process. The nanofabrication of amorphous SiAlCN ceramics was implemented with a focused ion beam (FIB). FIB conditions such as the milling rate, the beam current, and the number of passes were considered. It was found that nanopatterns with a feature size of less than 100 nm could be fabricated onto polymer-derived ceramics (PDCs) precisely and quickly. Specific nanostructures of thin walls, nozzle, and gear have been fabricated as demonstrations, indicating that the FIB technique was a promising method to realize nanostructures on PDCs, especially for microelectromechanical system and micro/nano-sensor applications. (paper)

  18. Immobilisation of an antibacterial drug to Ti6Al4V components fabricated using selective laser melting

    Energy Technology Data Exchange (ETDEWEB)

    Vaithilingam, Jayasheelan [Additive Manufacturing and 3D Printing Research Group, School of Engineering, University of Nottingham, Nottingham NG7 2RD (United Kingdom); Kilsby, Samuel [Department of Chemistry, Loughborough University, Loughborough LE11 3TU (United Kingdom); Goodridge, Ruth D., E-mail: Ruth.Goodridge@nottingham.ac.uk [Additive Manufacturing and 3D Printing Research Group, School of Engineering, University of Nottingham, Nottingham NG7 2RD (United Kingdom); Christie, Steven D.R. [Department of Chemistry, Loughborough University, Loughborough LE11 3TU (United Kingdom); Edmondson, Steve [School of Materials, The University of Manchester, Manchester M13 9PL (United Kingdom); Hague, Richard J.M. [Additive Manufacturing and 3D Printing Research Group, School of Engineering, University of Nottingham, Nottingham NG7 2RD (United Kingdom)

    2014-09-30

    Graphical abstract: The potential integration of selective laser melting (SLM) with surface modification using self-assembled monolayers for biomedical application has been investigated. Ciprofloxacin{sup ®} was functionalised to the SLM fabricated Ti6Al4V surface. Sustained release of the drug under in-vitro condition was witnessed. The inhibition zones showed the eluted drug was active against Staphylococcus aureus (a) and Escherichia coli (b) upon its release from the SLM fabricated part. - Highlights: • Parts fabricated using selective laser melting were coated with Ciprofloxacin{sup ®}. • The total amount of drug coated was approximately 1 μg/cm{sup 2}. • The coating was highly stable under oxidative conditions. • In-vitro studies showed a sustained release of the drug for over 42 days. • Ciprofloxacin{sup ®} eluted from the Ti6Al4V surface inhibited bacterial growth. - Abstract: Bacterial infections from biomedical implants and surgical devices are a major problem in orthopaedic, dental and vascular surgery. Although the sources of contaminations that lead to bacterial infections are known, it is not possible to control or avoid such infections completely. In this study, an approach to immobilise Ciprofloxacin{sup ®} (an antibacterial drug) to phosphonic acid based self-assembled monolayers (SAMs) adsorbed on a selectively laser melted (SLM) Ti6Al4V structure, has been presented. X-ray photoelectron spectroscopy (XPS) and static water contact angle measurements confirmed the attachment of SAMs and the drug. Results showed that Ciprofloxacin{sup ®} is highly stable under the oxidative conditions used in this study. In-vitro stability was estimated by immersing the Ciprofloxacin{sup ®} immobilised substrates in 10 mM of Tris–HCl buffer (pH-7.4) for 42 days. The Tris–HCl buffer was analysed using UV–vis spectrophotometry at 7, 14, 28 and 42 day time intervals to determine the release of the immobilised drug. The drug was observed to

  19. Immobilisation of an antibacterial drug to Ti6Al4V components fabricated using selective laser melting

    International Nuclear Information System (INIS)

    Vaithilingam, Jayasheelan; Kilsby, Samuel; Goodridge, Ruth D.; Christie, Steven D.R.; Edmondson, Steve; Hague, Richard J.M.

    2014-01-01

    Graphical abstract: The potential integration of selective laser melting (SLM) with surface modification using self-assembled monolayers for biomedical application has been investigated. Ciprofloxacin ® was functionalised to the SLM fabricated Ti6Al4V surface. Sustained release of the drug under in-vitro condition was witnessed. The inhibition zones showed the eluted drug was active against Staphylococcus aureus (a) and Escherichia coli (b) upon its release from the SLM fabricated part. - Highlights: • Parts fabricated using selective laser melting were coated with Ciprofloxacin ® . • The total amount of drug coated was approximately 1 μg/cm 2 . • The coating was highly stable under oxidative conditions. • In-vitro studies showed a sustained release of the drug for over 42 days. • Ciprofloxacin ® eluted from the Ti6Al4V surface inhibited bacterial growth. - Abstract: Bacterial infections from biomedical implants and surgical devices are a major problem in orthopaedic, dental and vascular surgery. Although the sources of contaminations that lead to bacterial infections are known, it is not possible to control or avoid such infections completely. In this study, an approach to immobilise Ciprofloxacin ® (an antibacterial drug) to phosphonic acid based self-assembled monolayers (SAMs) adsorbed on a selectively laser melted (SLM) Ti6Al4V structure, has been presented. X-ray photoelectron spectroscopy (XPS) and static water contact angle measurements confirmed the attachment of SAMs and the drug. Results showed that Ciprofloxacin ® is highly stable under the oxidative conditions used in this study. In-vitro stability was estimated by immersing the Ciprofloxacin ® immobilised substrates in 10 mM of Tris–HCl buffer (pH-7.4) for 42 days. The Tris–HCl buffer was analysed using UV–vis spectrophotometry at 7, 14, 28 and 42 day time intervals to determine the release of the immobilised drug. The drug was observed to release in a sustained manner. 50% of

  20. Three techniques for the fabrication of high precision, mm-sized metal components based on two-photon lithography, applied for manufacturing horn antennas for THz transceivers

    Science.gov (United States)

    Standaert, Alexander; Brancato, Luigi; Lips, Bram; Ceyssens, Frederik; Puers, Robert; Reynaert, Patrick

    2018-03-01

    This paper proposes a novel packaging solution which integrates micro-machined 3D horn antennas with millimeter-wave and THz tranceivers. This packaging solution is shown to be a valid competitor to existing technologies like metallic split-block waveguides and low temperature cofired ceramics. Three different fabrication methods based on two-photon lithography are presented to form the horn antennas. The first uses two-photon lithography to form the bulk of the antenna. This structure is then metalised through physical vapor deposition (PVD) and copper plating. The second fabrication method makes use of a soft polydimethylsiloxane (PDMS) mold to easily replicate structures and the third method forms the horn antenna through electroforming. A prototype is accurately positioned on top of a 400 GHz 28 nm CMOS transmitter and glued in place with epoxy, thus providing a fully packaged solution. Measurement results show a 12 dB increase in the antenna gain when using the packaged solution. The fabrication processes are not limited to horn antennas alone and can be used to form a wide range of mm-sized metal components.

  1. Micro-EDM process modeling and machining approaches for minimum tool electrode wear for fabrication of biocompatible micro-components

    DEFF Research Database (Denmark)

    Puthumana, Govindan

    2017-01-01

    Micro-electrical discharge machining (micro-EDM) is a potential non-contact method for fabrication of biocompatible micro devices. This paper presents an attempt to model the tool electrode wear in micro-EDM process using multiple linear regression analysis (MLRA) and artificial neural networks...... linear regression model was developed for prediction of TWR in ten steps at a significance level of 90%. The optimum architecture of the ANN was obtained with 7 hidden layers at an R-sq value of 0.98. The predicted values of TWR using ANN matched well with the practically measured and calculated values...... (ANN). The governing micro-EDM factors chosen for this investigation were: voltage (V), current (I), pulse on time (Ton) and pulse frequency (f). The proposed predictive models generate a functional correlation between the tool electrode wear rate (TWR) and the governing micro-EDM factors. A multiple...

  2. Method of fabricating free-form, high-aspect ratio components for high-current, high-speed microelectrics

    Science.gov (United States)

    Maxwell, James L; Rose, Chris R; Black, Marcie R; Springer, Robert W

    2014-03-11

    Microelectronic structures and devices, and method of fabricating a three-dimensional microelectronic structure is provided, comprising passing a first precursor material for a selected three-dimensional microelectronic structure into a reaction chamber at temperatures sufficient to maintain said precursor material in a predominantly gaseous state; maintaining said reaction chamber under sufficient pressures to enhance formation of a first portion of said three-dimensional microelectronic structure; applying an electric field between an electrode and said microelectronic structure at a desired point under conditions whereat said first portion of a selected three-dimensional microelectronic structure is formed from said first precursor material; positionally adjusting either said formed three-dimensional microelectronic structure or said electrode whereby further controlled growth of said three-dimensional microelectronic structure occurs; passing a second precursor material for a selected three-dimensional microelectronic structure into a reaction chamber at temperatures sufficient to maintain said precursor material in a predominantly gaseous state; maintaining said reaction chamber under sufficient pressures whereby a second portion of said three-dimensional microelectronic structure formation is enhanced; applying an electric field between an electrode and said microelectronic structure at a desired point under conditions whereat said second portion of a selected three-dimensional microelectronic structure is formed from said second precursor material; and, positionally adjusting either said formed three-dimensional microelectronic structure or said electrode whereby further controlled growth of said three-dimensional microelectronic structure occurs.

  3. Development of and verification test integral reactor major components - Development of manufacturing process and fabrication of prototype for SG and CEDM

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Chang Hee; Park, Hwa Kyu; Kim, Yong Kyu; Choi, Yong Soon; Kang, Ki Su; Hyun, Young Min [Korea Heavy Industries and Construction Co., LTD., Changwon (Korea)

    1999-03-01

    Integral SMART(System integrated Modular Advanced Reactor) type reactor is under conceptual design. Because major components is integrated within in a single pressure vessel, compact design using advanced technology is essential. It means that manufacturing process for these components is more complex and difficult. The objective of this study is to confirm the possibility of manufacture of Steam Generator, Control Element Drive Mechanism(CEDM) and Reactor Assembly which includes Reactor Pressure Vessel, it is important to understand the design requirement and function of the major components. After understanding the design requirement and function, it is concluded that the helical bending and weld qualification of titanium tube for Steam Generator and the applicability of electron beam weld for CEDM step motor parts is the critical to fabricate the components. Therefore, bending mock-up and weld qualification of titanium tube was performed and the results are quite satisfactory. Also, it is concluded that electron beam welding technique can be applicable to the CEDM step motor part. (author). 22 refs., 14 figs., 46 tabs.

  4. Design and fabrication of circular and rectangular components for electron-cyclotron-resonant heating of tandem mirror experiment-upgrade

    Energy Technology Data Exchange (ETDEWEB)

    Felker, B.; Calderon, M.O.; Chargin, A.K.; Coffield, F.E.; Lang, D.D.; Rubert, R.R.; Pedrotti, L.R.; Stallard, B.W.; Gallagher, N.C. Jr.; Sweeney, D.W.

    1983-11-18

    The electron-cyclotron-resonant heating (ECRH) systems of rectangular waveguides on Tandem Mirror Experiment-Upgrade (TMX-U) operated with a overall efficiency of 50%, each system using a 28-GHz, 200-kW pulsed gyrotron. We designed and built four circular-waveguide systems with greater efficiency and greater power-handling capabilities to replace the rectangular waveguides. Two of these circular systems, at the 5-kG second-harmonic heating locations, have a total transmission efficiency of >90%. The two systems at the 10-kG fundamental heating locations have a total transmission efficiency of 80%. The difference in efficiency is due to the additional components required to launch the microwaves in the desired orientation and polarization with respect to magnetic-field lines at the 10-kG points. These systems handle the total power available from each gyrotron but do not have the arcing limitation problem of the rectangular waveguide. Each system requires several complex components. The overall physical layout and the design considerations for the rectangular and circular waveguide components are described here.

  5. Design and fabrication of circular and rectangular components for electron-cyclotron-resonant heating of tandem mirror experiment-upgrade

    International Nuclear Information System (INIS)

    Felker, B.; Calderon, M.O.; Chargin, A.K.

    1983-01-01

    The electron-cyclotron-resonant heating (ECRH) systems of rectangular waveguides on Tandem Mirror Experiment-Upgrade (TMX-U) operated with a overall efficiency of 50%, each system using a 28-GHz, 200-kW pulsed gyrotron. We designed and built four circular-waveguide systems with greater efficiency and greater power-handling capabilities to replace the rectangular waveguides. Two of these circular systems, at the 5-kG second-harmonic heating locations, have a total transmission efficiency of >90%. The two systems at the 10-kG fundamental heating locations have a total transmission efficiency of 80%. The difference in efficiency is due to the additional components required to launch the microwaves in the desired orientation and polarization with respect to magnetic-field lines at the 10-kG points. These systems handle the total power available from each gyrotron but do not have the arcing limitation problem of the rectangular waveguide. Each system requires several complex components. The overall physical layout and the design considerations for the rectangular and circular waveguide components are described here

  6. Explosion bonding of dissimilar materials for fabricating APS front end components: Analysis of metallurgical and mechanical properties and UHV applications

    International Nuclear Information System (INIS)

    Li, Yuheng; Shu, Deming; Kuzay, T.M.

    1994-01-01

    The front end beamline section contains photon shutters and fixed masks. These components are made of OFHC copper and GlidCOP AL-15. Stainless steels (304 or 316) are also used for connecting photon shutters and fixed masks to other components that operate in the ultrahigh vacuum system. All these dissimilar materials need to be joined together. However, bonding these dissimilar materials is very difficult because of their different mechanical and thermal properties and incompatible metallurgical properties. Explosion bonding is a bonding method in which the controlled energy of a detonating explosive is used to create a metallurgical bond between two or more similar or dissimilar materials. No intermediate filler metal, for example, a brazing compound or soldering alloy, is needed to promote bonding, and no external heat need be applied. A study of the metallurgical and mechanical properties and YGV applications of GlidCop AL-15, OFHC copper, and 304 stainless steel explosion-bonded joints has been done. This report contains five parts: an ultrasonic examination of explosion-bonded joints and a standard setup; mechanical-property and thermal-cycle tests of GlidCop AL-15/304 stainless steel explosion-bonded joints; leak tests of a GlidCop AL-15/304 stainless steel explosion-bonded interfaces for UHV application; metallurgical examination of explosion-bonded interfaces and failure analysis, and discussion and conclusion

  7. 3D Microstructural Architectures for Metal and Alloy Components Fabricated by 3D Printing/Additive Manufacturing Technologies

    Science.gov (United States)

    Martinez, E.; Murr, L. E.; Amato, K. N.; Hernandez, J.; Shindo, P. W.; Gaytan, S. M.; Ramirez, D. A.; Medina, F.; Wicker, R. B.

    The layer-by-layer building of monolithic, 3D metal components from selectively melted powder layers using laser or electron beams is a novel form of 3D printing or additive manufacturing. Microstructures created in these 3D products can involve novel, directional solidification structures which can include crystallographically oriented grains containing columnar arrays of precipitates characteristic of a microstructural architecture. These microstructural architectures are advantageously rendered in 3D image constructions involving light optical microscopy and scanning and transmission electron microscopy observations. Microstructural evolution can also be effectively examined through 3D image sequences which, along with x-ray diffraction (XRD) analysis in the x-y and x-z planes, can effectively characterize related crystallographic/texture variances. This paper compares 3D microstructural architectures in Co-base and Ni-base superalloys, columnar martensitic grain structures in 17-4 PH alloy, and columnar copper oxides and dislocation arrays in copper.

  8. Preliminary construction of integral analysis for characteristic components in complex matrices by in-house fabricated solid-phase microextraction fibers combined with gas chromatography-mass spectrometry.

    Science.gov (United States)

    Tang, Zhentao; Hou, Wenqian; Liu, Xiuming; Wang, Mingfeng; Duan, Yixiang

    2016-08-26

    Integral analysis plays an important role in study and quality control of substances with complex matrices in our daily life. As the preliminary construction of integral analysis of substances with complex matrices, developing a relatively comprehensive and sensitive methodology might offer more informative and reliable characteristic components. Flavoring mixtures belonging to the representatives of substances with complex matrices have now been widely used in various fields. To better study and control the quality of flavoring mixtures as additives in food industry, an in-house fabricated solid-phase microextraction (SPME) fiber was prepared based on sol-gel technology in this work. The active organic component of the fiber coating was multi-walled carbon nanotubes (MWCNTs) functionalized with hydroxyl-terminated polydimethyldiphenylsiloxane, which integrate the non-polar and polar chains of both materials. In this way, more sensitive extraction capability for a wider range of compounds can be obtained in comparison with commercial SPME fibers. Preliminarily integral analysis of three similar types of samples were realized by the optimized SPME-GC-MS method. With the obtained GC-MS data, a valid and well-fit model was established by partial least square discriminant analysis (PLS-DA) for classification of these samples (R2X=0.661, R2Y=0.996, Q2=0.986). The validity of the model (R2=0.266, Q2=-0.465) has also approved the potential to predict the "belongingness" of new samples. With the PLS-DA and SPSS method, further screening out the markers among three similar batches of samples may be helpful for monitoring and controlling the quality of the flavoring mixtures as additives in food industry. Conversely, the reliability and effectiveness of the GC-MS data has verified the comprehensive and efficient extraction performance of the in-house fabricated fiber. Copyright © 2016 Elsevier B.V. All rights reserved.

  9. Fabrication processes of C/Sic composites for high temperature components in energy systems and investigation of their oxidation behavior

    International Nuclear Information System (INIS)

    El-Hakim, E.

    2004-01-01

    Carbon fibre-reinforced ceramic matrix composite are promising candidate materials for high temperature applications such as structural components in energy systems, fusion reactors and advanced gas turbine engines. C/C composites has low oxidation resistance at temperatures above 500degree. To overcome this low oxidation resistance a coating should be applied. Tenax HTA 5131 carbon fibres impregnated with phenolic resin and reinforced silicon carbide were modified by the addition of a coating layer of boron oxide, (suspended in Dyansil-40) for improving anti-oxidation properties of the composites.The oxidation behavior of carbon-silicon carbide composites coated with B 2 O 3 , as an protective layer former, in dry air has been studied in the temperature range 800- 1000 degree for 8 hrs and 16 hrs. The results show that the oxidation rates of the uncoated composites samples are higher than those of the coated composites. The uncoated samples exhibit the highest oxidation rate during the initial stages of oxidation. The composite coated with B 2 O 3 had a significantly improved oxidation resistance due to the formation of a barrier layer for oxygen diffusion. This improvement in the oxidation resistance is attributed to the blocking of the active sites for oxygen diffusion. The oxidation resistance of the coated composite is highly improved; the weight loss percentage of casted samples is 4.5-16% after 16-hrs oxidation in air while the weight loss of uncoated samples is about 60%. The results are supported by scanning electron microscopy

  10. Fabrication and characterization of a metal-packaged regenerated fiber Bragg grating strain sensor for structural integrity monitoring of high-temperature components

    International Nuclear Information System (INIS)

    Tu, Yun; Tu, Shan-Tung

    2014-01-01

    Assessment of the structural integrity of components operating at high temperatures requires the development of novel sensors to measure strain. A metal-packaged regenerated fiber Bragg grating (RFBG) sensor is developed for measurement of strain using titanium–silver magnetron sputtering and nickel electroplating. The strain response of the sensor mounted onto a flat tensile specimen by spot welding is evaluated by uniaxial tensile tests at constant temperatures ranging from room temperature to 400 °C. Similar tests are performed on a bare RFBG sensor for comparison. The metal-packaged RFBG strain sensor exhibits higher strain sensitivity than that of the bare RFBG sensor, as well as good linearity, stability and repeatability of strain measurements. A three-dimensional finite element model of the sensor is established to predict the strain sensitivity based on the sensing principle of the fiber Bragg grating. Comparisons of the experimental results with the numerical predictions for the strain sensitivity show a satisfactory agreement. These results demonstrate that the metal-packaged RFBG strain sensors can be successfully fabricated by combining magnetron sputtering with electroplating, and provide great promise for structural integrity monitoring of high-temperature components. (paper)

  11. Laser fabrication of beryllium components

    International Nuclear Information System (INIS)

    Hanafee, J.E.; Ramos, T.J.

    1995-08-01

    Working with the beryllium industry on commercial applications and using prototype parts, the authors have found that the use of lasers provides a high-speed, low-cost method of cutting beryllium metal, beryllium alloys, and beryllium-beryllium oxide composites. In addition, they have developed laser welding processes for commercial structural grades of beryllium that do not need a filler metal; i.e., autogenous welds were made in commercial structural grades of beryllium by using lasers

  12. Mechanical and tribological properties of polymer-derived Si/C/N sub-millimetre thick miniaturized components fabricated by direct casting

    OpenAIRE

    Bakumov Vadym; Blugan Gurdial; Roos Sigfried; Graule Thomas J.; Fakhfouri Vahid; Grossenbacher Jonas; Gullo Maurizio Rosario; Kiefer Thomas C.; Brugger Juergen; Parlinska Magdalena; Kuebler Jakob

    2012-01-01

    The utilization of silicon based polymers as a source of amorphous non oxide ceramics obtained upon pyrolytic treatment of them is increasingly gaining attention in research and is currently expanding into the field of commercial products. This work is focused on the near net shaped fabrication mechanical and tribological properties of a polymer derived Si/C/N system. Small sub millimetre thick ceramic test discs and bars were fabricated by casting of polysilazane and/or polycarbosilane precu...

  13. Construction, fabrication, and installation

    International Nuclear Information System (INIS)

    1992-05-01

    This standard specifies the construction, fabrication, and installation requirements that apply to concrete containment structures of a containment system designated as class containment components, parts and appurtenances for nuclear power plants

  14. An Open-Source Building System with Digitally Fabricated Components : A design- and production process that makes optimal use of the predicted next industrial revolution

    NARCIS (Netherlands)

    Stoutjesdijk, P.M.M.

    2013-01-01

    With digital fabrication, our hardware is starting to bear greater resemblance to software. This paper explores the potential of processes used in the development of open-source software for the field of Architecture. The developed design process is connected to a building system that provides new

  15. Strength of PLA Components Fabricated with Fused Deposition Technology Using a Desktop 3D Printer as a Function of Geometrical Parameters of the Process

    Directory of Open Access Journals (Sweden)

    Vladimir E. Kuznetsov

    2018-03-01

    Full Text Available The current paper studies the influence of geometrical parameters of the fused deposition modeling (FDM—fused filament fabrication (FFF 3D printing process on printed part strength for open source desktop 3D printers and the most popular material used for that purpose—i.e., polylactic acid (PLA. The study was conducted using a set of different nozzles (0.4, 0.6, and 0.8 mm and a range of layer heights from the minimum to maximum physical limits of the machine. To assess print strength, a novel assessment method is proposed. A tubular sample is loaded in the weakest direction (across layers in a three-point bending fixture. Mesostructure evaluation through scanning electronic microscopy (SEM scans of the samples was used to explain the obtained results. We detected a significant influence of geometric process parameters on sample mesostructure, and consequently, on sample strength.

  16. Fabrication Facilities

    Data.gov (United States)

    Federal Laboratory Consortium — The Fabrication Facilities are a direct result of years of testing support. Through years of experience, the three fabrication facilities (Fort Hood, Fort Lewis, and...

  17. Fabricating off-diagonal components of frequency-dependent linear and nonlinear polarizabilities of doped quantum dots by Gaussian white noise

    Energy Technology Data Exchange (ETDEWEB)

    Saha, Surajit [Department of Chemistry, Bishnupur Ramananda College, Bishnupur, Bankura 722122, West Bengal (India); Ganguly, Jayanta [Department of Chemistry, Brahmankhanda Basapara High School, Basapara, Birbhum 731215, West Bengal (India); Ghosh, Manas, E-mail: pcmg77@rediffmail.com [Department of Chemistry, Physical Chemistry Section, Visva Bharati University, Santiniketan, Birbhum 731 235, West Bengal (India)

    2015-07-15

    We make a rigorous exploration of the profiles of off-diagonal components of frequency-dependent linear (α{sub xy}, α{sub yx}), first nonlinear (β{sub xyy}, β{sub yxx}), and second nonlinear (γ{sub xxyy}, γ{sub yyxx}) polarizabilities of quantum dots driven by Gaussian white noise. The quantum dot is doped with repulsive Gaussian impurity. Noise has been applied additively and multiplicatively to the system. An external oscillatory electric field has also been applied to the system. Gradual variations of external frequency, dopant location, and noise strength give rise to interesting features of polarizability components. The observations reveal intricate interplay between noise strength and dopant location which designs the polarizability profiles. Moreover, the mode of application of noise also modulates the polarizability components. Interestingly, in case of additive noise the noise strength has no role on polarizabilities whereas multiplicative noise invites greater delicacy in them. The said interplay provides a rather involved framework to attain stable, enhanced, and often maximized output of linear and nonlinear polarizabilities. - Highlights: • Linear and nonlinear polarizabilities of quantum dot are studied. • The polarizability components are off-diagonal and frequency-dependent. • Quantum dot is doped with a repulsive impurity. • Doped system is subject to Gaussian white noise. • Mode of noise application affects polarizabilities.

  18. Experimental Studies of Selected Aqueous Electrochemical Systems Relevant for Materials Processing in the Fabrications of Microelectronic Components and Direct Alcohol Fuel Cells

    Science.gov (United States)

    Shi, Xingzhao

    A broad range of electrochemical techniques are employed in this dissertation to investigate a selected set of aqueous electrochemical systems that are relevant for materials processing in the fabrication of microelectronic devices and direct alcohol fuel cells. In terms of technical applications, this work covers three main experimental systems: (i) chemical mechanical planarization (CMP), (ii) electro-less nickel deposition, and (iii) direct alkaline glycerol fuel cells. The first two areas are related to electronic device fabrications and the third topic is related to cost-effective energy conversion. The common electrochemical aspect of these different systems is that, in all these cases the active material characteristics are governed by complex (often multi-step) reactions occurring at metal-liquid (aqueous) interfaces. Electro-analytical techniques are ideally suited for studying the detailed mechanisms of such reactions, and the present investigation is largely focused on developing adequate analytical strategies for probing these reaction mechanisms. In the fabrication of integrated circuits, certain steps of materials processing involve CMP of Al deposited on thin layers of diffusion barrier materials like Ta/TaN, Co, or Ti/TiN. A specific example of this situation is found in the processing of replacement metal gates used for high-k/metal-gate transistors. Since the commonly used barrier materials are nobler than Al, the Al interface in contact with the barrier can become prone to galvanic corrosion in the wet CMP environment. Using model systems of coupon electrodes and two specific barrier metals, Ta and Co, the electrochemical factors responsible for these corrosion effects are investigated here in a moderately acidic (pH = 4.0) abrasive-free solution. The techniques of cyclic voltammetry and impedance spectroscopy are combined with strategic measurements of galvanic currents and open circuit potentials (OCPs). L-ascorbic acid (AA) is employed as a

  19. Design, fabrication and testing of an improved high heat flux element, experience feedback on steady state plasma facing components in Tore Supra

    International Nuclear Information System (INIS)

    Schlosser, J.; Chappuis, P.; Chatelier, M.; Durocher, A.; Guilheim, D.; Lipa, M.; Mitteau, R.; Tonon, G.; Tsitrone, E.

    1998-01-01

    Actively cooled plasma facing components (PFC) have been developed and used in Tore Supra since 1985. One of the main technological problem is due to the expansion mismatch between graphite armour and metallic heat sink material. A first technology used graphite tiles with or without a reinforcement and a compliant layer, brazed with titanium copper-silver (TiCuAg) alloy. The next technology used carbon fiber material (CFC) tiles with a 2 mm pure copper compliant layer, since the good mechanical strength of the CFC allowed the reinforcement layer to be suppressed. No destructive inspection during the manufacturing procedure was found to be essential to insure a good reliability of the elements. (orig.)

  20. Fabrication and Investigation of Two-Component Film of 2,5-Diphenyloxazole and Octafluoronaphthalene Exhibiting Tunable Blue/Bluish Violet Fluorescence Based on Low Vacuum Physical Vapor Deposition Method

    Directory of Open Access Journals (Sweden)

    Xiaoyu Zhai

    2016-01-01

    Full Text Available Organic luminescent materials play an important role in the fields of light-emitting diodes and fluorescent imaging. Moreover, new synthetic approaches towards π-conjugated molecular systems with high fluorescence quantum efficiency are highly desired. Herein, different 2,5-diphenyloxazole-octafluoronaphthalene (DPO-OFN films with tunable fluorescence have been prepared by Low Vacuum Physical Vapor Deposition (LVPVD method. DPO-OFN films showed some changed properties, such as molecular vibration and fluorescence. All films exhibited blue/bluish violet fluorescence and showed blue shift, in comparison with pristine DPO. This work introduced a new method to fabricate two-component molecular materials with tunable blue/bluish violet luminescence properties and provided a new perspective to prepare organic luminescent film materials, layer film materials, cocrystal materials, and cocrystal film materials. Importantly, these materials have potential applications in the fields of next generation of photofunctional materials.

  1. Benefits of Hot Isostatic Pressure/Powdered Metal (HIP/PM) and Additive Manufacturing (AM) To Fabricate Advanced Energy System Components

    Energy Technology Data Exchange (ETDEWEB)

    Horton, Nancy [Energy Industries of Ohio, Cleveland, OH (United States); Sheppard, Roy [Energy Industries of Ohio, Cleveland, OH (United States)

    2016-12-31

    Advanced Energy systems require large, complex components produced from materials capable of withstanding severe operating environments (high temperature, pressure, corrosivity). Such parts can be difficult to source, as conventional material processing technologies must be tailored to ensure a safe and cost effective approach to large-scale manufacture of quality structural advanced alloy components that meet the performance specifications of AE systems. (HIP/PM) has shown advantages over other manufacturing methods when working with these materials. For example, using HIP’ing in lieu of casting means significant savings in raw material costs, which for expensive, high-nickel alloys can be considerable for large-scale production. Use of HIP/PM also eliminates the difficulties resulting from reactivity of these materials in the molten state and facilitates manufacture of the large size requirements of the AE industry, producing a part that is defect and porosity free, thus further reducing or eliminating time and expense of post processing machining and weld repair. New advances in Additive Manufacturing (AM) techniques make it possible to further expand the benefits of HIP/PM in producing AE system components to create an even more robust manufacturing approach. Traditional techniques of welding and forming sheet metal to produce the HIP canisters can be time consuming and costly, with limitations on the complexity of part which can be achieved. A key benefit of AM is the freedom of design that it offers, so use of AM could overcome such challenges, ultimately enabling redesign of complete energy systems. A critical step toward this goal is material characterization of the required advanced alloys, for use in AM. Using Haynes 282, a high nickel alloy of interest to the Fossil Energy community, particularly for Advanced-UltraSuperCritical (AUSC) operating environments, as well as the crosscutting interests of the aerospace, defense and medical markets, this

  2. Digital fabrication

    CERN Document Server

    2012-01-01

    The Winter 2012 (vol. 14 no. 3) issue of the Nexus Network Journal features seven original papers dedicated to the theme “Digital Fabrication”. Digital fabrication is changing architecture in fundamental ways in every phase, from concept to artifact. Projects growing out of research in digital fabrication are dependent on software that is entirely surface-oriented in its underlying mathematics. Decisions made during design, prototyping, fabrication and assembly rely on codes, scripts, parameters, operating systems and software, creating the need for teams with multidisciplinary expertise and different skills, from IT to architecture, design, material engineering, and mathematics, among others The papers grew out of a Lisbon symposium hosted by the ISCTE-Instituto Universitario de Lisboa entitled “Digital Fabrication – A State of the Art”. The issue is completed with four other research papers which address different mathematical instruments applied to architecture, including geometric tracing system...

  3. Nuclear Fabrication Consortium

    Energy Technology Data Exchange (ETDEWEB)

    Levesque, Stephen [EWI, Columbus, OH (United States)

    2013-04-05

    This report summarizes the activities undertaken by EWI while under contract from the Department of Energy (DOE) Office of Nuclear Energy (NE) for the management and operation of the Nuclear Fabrication Consortium (NFC). The NFC was established by EWI to independently develop, evaluate, and deploy fabrication approaches and data that support the re-establishment of the U.S. nuclear industry: ensuring that the supply chain will be competitive on a global stage, enabling more cost-effective and reliable nuclear power in a carbon constrained environment. The NFC provided a forum for member original equipment manufactures (OEM), fabricators, manufacturers, and materials suppliers to effectively engage with each other and rebuild the capacity of this supply chain by : Identifying and removing impediments to the implementation of new construction and fabrication techniques and approaches for nuclear equipment, including system components and nuclear plants. Providing and facilitating detailed scientific-based studies on new approaches and technologies that will have positive impacts on the cost of building of nuclear plants. Analyzing and disseminating information about future nuclear fabrication technologies and how they could impact the North American and the International Nuclear Marketplace. Facilitating dialog and initiate alignment among fabricators, owners, trade associations, and government agencies. Supporting industry in helping to create a larger qualified nuclear supplier network. Acting as an unbiased technology resource to evaluate, develop, and demonstrate new manufacturing technologies. Creating welder and inspector training programs to help enable the necessary workforce for the upcoming construction work. Serving as a focal point for technology, policy, and politically interested parties to share ideas and concepts associated with fabrication across the nuclear industry. The report the objectives and summaries of the Nuclear Fabrication Consortium

  4. Fabrication and Characterization of Photonic Bandgap Components

    DEFF Research Database (Denmark)

    Frandsen, Lars Hagedorn

    2006-01-01

    Denne ph.d. afhandling beskæftiger sig med modelleringen, fabrikationen og karakteriseringen af fotoniske båndgabs komponenter, som er realiseret i et silicium-på-isolator materiale. Metoderne "plane-wave expansion theory" og "finite-difference time-domain modelling" er blevet anvendt til at mode...

  5. Fabrication and Characterisation of Optical Semiconductor Components

    DEFF Research Database (Denmark)

    Christiansen, Lotte Jin

    2006-01-01

    Formålet med projektet har været at fremstille en ny og simpel halvleder komponent til regenerering af optiske telekommunikations signaler. Mange af de hidtil mest brugte komponenter til dette formål er såkaldte interferometre, som kan være meget svære at fremstille rent procesteknisk, samtidig m...

  6. Fabrication of Micro Components by Electrochemical Deposition

    DEFF Research Database (Denmark)

    Tang, Peter Torben

    The main issue of this thesis is the combination of electrochemical deposition of metals and micro machining. Processes for electroplating and electroless plating of nickel and nickel alloys have been developed and optimised for compatibility with microelectronics and silicon based micromechanics...

  7. Using Powder Cored Tubular Wire Technology to Enhance Electron Beam Freeform Fabricated Structures

    Science.gov (United States)

    Gonzales, Devon; Liu, Stephen; Domack, Marcia; Hafley, Robert

    2016-01-01

    Electron Beam Freeform Fabrication (EBF3) is an additive manufacturing technique, developed at NASA Langley Research Center, capable of fabricating large scale aerospace parts. Advantages of using EBF3 as opposed to conventional manufacturing methods include, decreased design-to-product time, decreased wasted material, and the ability to adapt controls to produce geometrically complex parts with properties comparable to wrought products. However, to fully exploit the potential of the EBF3 process development of materials tailored for the process is required. Powder cored tubular wire (PCTW) technology was used to modify Ti-6Al-4V and Al 6061 feedstock to enhance alloy content, refine grain size, and create a metal matrix composite in the as-solidified structures, respectively.

  8. Status report, canister fabrication

    Energy Technology Data Exchange (ETDEWEB)

    Andersson, Claes-Goeran; Eriksson, Peter; Westman, Marika [Swedish Nuclear Fuel and Waste Management Co., Stockholm (Sweden); Emilsson, Goeran [CSM Materialteknik AB, Linkoeping (Sweden)

    2004-06-01

    The report gives an account of the development of material and fabrication technology for copper canisters with cast inserts during the period from 2000 until the start of 2004. The engineering design of the canister and the choice of materials in the constituent components described in previous status reports have not been significantly changed. In the reference canister, the thickness of the copper shell is 50 mm. Fabrication of individual components with a thinner copper thickness is done for the purpose of gaining experience and evaluating fabrication and inspection methods for such canisters. As a part of the development of cast inserts, computer simulations of the casting processes and techniques used at the foundries have been performed for the purpose of optimizing the material properties. These properties have been evaluated by extensive tensile testing and metallographic inspection of test material taken from discs cut at different points along the length of the inserts. The testing results exhibit a relatively large spread. Low elongation values in certain tensile test specimens are due to the presence of poorly formed graphite, porosities, slag or other casting defects. It is concluded in the report that it will not be possible to avoid some presence of observed defects in castings of this size. In the deep repository, the inserts will be exposed to compressive loading and the observed defects are not critical for strength. An analysis of the strength of the inserts and formulation of relevant material requirements must be based on a statistical approach with probabilistic calculations. This work has been initiated and will be concluded during 2004. An initial verifying compression test of a canister in an isostatic press has indicated considerable overstrength in the structure. Seamless copper tubes are fabricated by means of three methods: extrusion, pierce and draw processing, and forging. It can be concluded that extrusion tests have revealed a

  9. Adaptive Control of Freeze-Form Extrusion Fabrication Processes (Preprint)

    National Research Council Canada - National Science Library

    Zhao, Xiyue; Landers, Robert G; Leu, Ming C

    2008-01-01

    Freeze-form Extrusion Fabrication (FEF) is an additive manufacturing process that extrudes high solids loading aqueous ceramic pastes in a layer-by-layer fashion below the paste freezing temperature for component fabrication...

  10. ProtoCology : Integrating modular robotics and non standard fabrication

    NARCIS (Netherlands)

    Friedrich, H.C.

    2011-01-01

    Modular robotics and architectural designs built from CNC-fabricated unique components are two emergent research areas in which technologies such as integrated parametric design and fabrication, digital control and mechatronics affect construction and (re) configuration of built environments. These

  11. An Ethology of Urban Fabric(s)

    DEFF Research Database (Denmark)

    Fritsch, Jonas; Thomsen, Bodil Marie Stavning

    2014-01-01

    The article explores a non-metaphorical understanding of urban fabric(s), shifting the attention from a bird’s eye perspective to the actual, textural manifestations of a variety of urban fabric(s) to be studied in their real, processual, ecological and ethological complexity within urban life. We...... effectuate this move by bringing into resonance a range of intersecting fields that all deal with urban fabric(s) in complementary ways (interaction design and urban design activism, fashion, cultural theory, philosophy, urban computing)....

  12. Fabrication of mercury target vessel

    International Nuclear Information System (INIS)

    Wakui, Takashi; Kogawa, Hiroyuki; Haga, Katsuhiro; Futakawa, Masatoshi; Hayashi, Ryoichi; Uchiyama, Naoyoshi; Okamoto, Yoshinao; Nakamura, Koji

    2010-03-01

    The construction of materials and life science experimental facility in J-PARC (Japan Proton Accelerator Complex) project had been completed and accepted pulsed proton beams with low power. Since 2003, the detailed design, fabrication and examination for the mercury target vessel as a pulsed neutron source were carried out by the vender. The mercury target vessel consists of triple-walled structure in order to prevent the leak of mercury to outside at the failure of the mercury vessel and to remove the heat of the safety hull, which covers the mercury vessel, due to the injection of the pulsed proton beams. The high fabrication accuracy is required for the mercury target vessel assembled by the welding, because there are the relationships between the mercury target vessel and other components (target trolley, target storage container, flange of helium vessel, reflector and water-cooled shield). At each fabrication step, the examinations for the mercury target vessel with multi-walled structure were required. In this report, the required specification and basic structure of parts in the mercury target vessel are described and the fabrication procedure of the mercury target vessel by the vender is reported. In the fabrication of the mercury target vessel, there were many troubles such as large deformation due to the welding and then the vender repaired and brought the mercury target vessel to completion. Furthermore, improvements for the design and fabrication of the mercury target are reported. (author)

  13. Fabrication and Prototyping Lab

    Data.gov (United States)

    Federal Laboratory Consortium — Purpose: The Fabrication and Prototyping Lab for composite structures provides a wide variety of fabrication capabilities critical to enabling hands-on research and...

  14. Fabrication Aware Form-finding

    DEFF Research Database (Denmark)

    Egholm Pedersen, Ole; Larsen, Niels Martin; Pigram, Dave

    2014-01-01

    parts. The first material system employs a novel rotated joint design to allow the structural tuning of quasi-reciprocal timber frame elements fabricated from multi-axis machined plywood sheet stock. The second em-loys discontinuous post-tensioning to assemble unique precast concrete components......This paper describes a design and construction method that combines two distinct material systems with fabrication aware form-finding and file-to-factory workflows. The method enables the fluent creation of complex materially efficient structures comprising high populations of geometrically unique...

  15. Fabrication of recyclable superhydrophobic cotton fabrics

    Science.gov (United States)

    Han, Sang Wook; Park, Eun Ji; Jeong, Myung-Geun; Kim, Il Hee; Seo, Hyun Ook; Kim, Ju Hwan; Kim, Kwang-Dae; Kim, Young Dok

    2017-04-01

    Commercial cotton fabric was coated with SiO2 nanoparticles wrapped with a polydimethylsiloxane (PDMS) layer, and the resulting material surface showed a water contact angle greater than 160°. The superhydrophobic fabric showed resistance to water-soluble contaminants and maintained its original superhydrophobic properties with almost no alteration even after many times of absorption-washing cycles of oil. Moreover, superhydrophobic fabric can be used as a filter to separate oil from water. We demonstrated a simple method of fabrication of superhydrophobic fabric with potential interest for use in a variety of applications.

  16. Polymorphous computing fabric

    Science.gov (United States)

    Wolinski, Christophe Czeslaw [Los Alamos, NM; Gokhale, Maya B [Los Alamos, NM; McCabe, Kevin Peter [Los Alamos, NM

    2011-01-18

    Fabric-based computing systems and methods are disclosed. A fabric-based computing system can include a polymorphous computing fabric that can be customized on a per application basis and a host processor in communication with said polymorphous computing fabric. The polymorphous computing fabric includes a cellular architecture that can be highly parameterized to enable a customized synthesis of fabric instances for a variety of enhanced application performances thereof. A global memory concept can also be included that provides the host processor random access to all variables and instructions associated with the polymorphous computing fabric.

  17. Woven Apparel Fabrics

    OpenAIRE

    Redmore, Nicola

    2012-01-01

    This chapter considers the different woven manufacturing\\ud processes used in the production of apparel fabrics. It details the mainapparel fabric types and looks at the key performance requirements of those fabrics, in relation to both the weave structure and the fibre type. The chapter then goes on to briefly describe important considerations in the design process and the various end uses for woven fabric. Application examples detailed towards the end of the chapter include fabrics that are...

  18. Modeling of Shock Propagation and Attenuation in Viscoelastic Components

    Directory of Open Access Journals (Sweden)

    R. Rusovici

    2001-01-01

    Full Text Available Protection from the potentially damaging effects of shock loading is a common design requirement for diverse mechanical structures ranging from shock accelerometers to spacecraft. High damping viscoelastic materials are employed in the design of geometrically complex, impact-absorbent components. Since shock transients are characterized by a broad frequency spectrum, it is imperative to properly model frequency dependence of material behavior over a wide frequency range. The Anelastic Displacement Fields (ADF method is employed herein to model frequency-dependence within a time-domain finite element framework. Axisymmetric, ADF finite elements are developed and then used to model shock propagation and absorption through viscoelastic structures. The model predictions are verified against longitudinal wave propagation experimental data and theory.

  19. ITER Central Solenoid Module Fabrication

    Energy Technology Data Exchange (ETDEWEB)

    Smith, John [General Atomics, San Diego, CA (United States)

    2016-09-23

    The fabrication of the modules for the ITER Central Solenoid (CS) has started in a dedicated production facility located in Poway, California, USA. The necessary tools have been designed, built, installed, and tested in the facility to enable the start of production. The current schedule has first module fabrication completed in 2017, followed by testing and subsequent shipment to ITER. The Central Solenoid is a key component of the ITER tokamak providing the inductive voltage to initiate and sustain the plasma current and to position and shape the plasma. The design of the CS has been a collaborative effort between the US ITER Project Office (US ITER), the international ITER Organization (IO) and General Atomics (GA). GA’s responsibility includes: completing the fabrication design, developing and qualifying the fabrication processes and tools, and then completing the fabrication of the seven 110 tonne CS modules. The modules will be shipped separately to the ITER site, and then stacked and aligned in the Assembly Hall prior to insertion in the core of the ITER tokamak. A dedicated facility in Poway, California, USA has been established by GA to complete the fabrication of the seven modules. Infrastructure improvements included thick reinforced concrete floors, a diesel generator for backup power, along with, cranes for moving the tooling within the facility. The fabrication process for a single module requires approximately 22 months followed by five months of testing, which includes preliminary electrical testing followed by high current (48.5 kA) tests at 4.7K. The production of the seven modules is completed in a parallel fashion through ten process stations. The process stations have been designed and built with most stations having completed testing and qualification for carrying out the required fabrication processes. The final qualification step for each process station is achieved by the successful production of a prototype coil. Fabrication of the first

  20. Electronic components and systems

    CERN Document Server

    Dennis, W H

    2013-01-01

    Electronic Components and Systems focuses on the principles and processes in the field of electronics and the integrated circuit. Covered in the book are basic aspects and physical fundamentals; different types of materials involved in the field; and passive and active electronic components such as capacitors, inductors, diodes, and transistors. Also covered in the book are topics such as the fabrication of semiconductors and integrated circuits; analog circuitry; digital logic technology; and microprocessors. The monograph is recommended for beginning electrical engineers who would like to kn

  1. Zircaloy 4 ingots' industrial fabrication

    International Nuclear Information System (INIS)

    Leyt, A.

    1987-01-01

    The technology developed for the industrial fabrication of Zircaloy-4 ingots is presented. According to the results obtained: a) the homogeneity of the ingots is analyzed, regarding the distribution of components (tin, iron, chromium, oxygen) and Brinell hardness as a function of different types of charge: zirconium sponge-recycling alloy material, sponge of zirconium-alloy; b) the distribution of the same parameters as a function of production is also analyzed. (Author)

  2. Woven Fabrics Made of Auxetic Plied Yarns

    Directory of Open Access Journals (Sweden)

    Wing Sum Ng

    2018-02-01

    Full Text Available Auxetic plied yarns are specially constructed with two types of single yarns of different sizes and moduli. This paper investigates how to use these types of yarns to produce woven fabrics with auxetic effects. Four-ply auxetic yarns were first incorporated into a series of woven fabrics with different design parameters to study their auxetic behavior and percent open area during extension. Effects of auxetic plied yarn arrangement, single component yarn properties, weft yarn type, and weave structure were then evaluated. Additional double helical yarn (DHY and 6-ply auxetic yarn woven fabrics were also made for comparison. The results show that the alternative arrangement of S- and Z-twisted 4-ply auxetic yarns in a woven fabric can generate a higher negative Poisson’s ratio (NPR of the fabric. While the higher single stiff yarn modulus of auxetic yarn can result in greater NPR behavior, finer soft auxetic yarn does not necessarily generate such an effect. Weft yarns with low modulus and short float over the 4-ply auxetic yarns in fabric structure are favorable for producing high NPR behavior. The weft cover factor greatly affects the variation of the percent open area of the 4-ply auxetic yarn fabrics during extension. When different kinds of helical auxetic yarns (HAYs are made into fabrics, the fabric made of DHY does not have the highest NPR effect but it has the highest percent open area, which increases with increasing tensile strain.

  3. FABRIC QUALITY CONTROL SYSTEMS

    Directory of Open Access Journals (Sweden)

    Özlem KISAOĞLU

    2006-02-01

    Full Text Available Woven fabric quality depends on yarn properties at first, then weaving preparation and weaving processes. Defect control of grey and finished fabric is done manually on the lighted tables or automatically. Fabrics can be controlled by the help of the image analysis method. In image system the image of fabrics can be digitized by video camera and after storing controlled by the various processing. Recently neural networks, fuzzy logic, best wavelet packet model on automatic fabric inspection are developed. In this study the advantages and disadvantages of manual and automatic, on-line fabric inspection systems are given comparatively.

  4. Fused deposition of ceramics: A comprehensive experimental, analytical and computational study of material behavior, fabrication process and equipment design

    Science.gov (United States)

    Bellini, Anna

    Customer-driven product customization and continued demand for cost and time savings have generated a renewed interest in agile manufacturing based on improvements on Rapid Prototyping (RP) technologies. The advantages of RP technologies are: (1) ability to shorten the product design and development time, (2) suitability for automation and decrease in the level of human intervention, (3) ability to build many geometrically complex shapes. A shift from "prototyping" to "manufacturing" necessitates the following improvements: (1) Flexibility in choice of materials; (2) Part integrity and built-in characteristics to meet performance requirements; (3) Dimensional stability and tolerances; (4) Improved surface finish. A project funded by ONR has been undertaken to develop an agile manufacturing technology for fabrication of ceramic and multi-component parts to meet various needs of the Navy, such as transducers, etc. The project is based on adaptation of a layered manufacturing concept since the program required that the new technology be developed based on a commercially available RP technology. Among various RP technologies available today, Fused Deposition Modeling (FDM) has been identified as the focus of this research because of its potential versatility in the choice of materials and deposition configuration. This innovative approach allows for designing and implementing highly complex internal architectures into parts through deposition of different materials in a variety of configurations in such a way that the finished product exhibit characteristics to meet the performance requirements. This implies that, in principle, one can tailor-make the assemble of materials and structures as per specifications of an optimum design. The program objectives can be achieved only through accurate process modeling and modeling of material behavior. Oftentimes, process modeling is based on some type of computational approach where as modeling of material behavior is based on

  5. Other components

    International Nuclear Information System (INIS)

    Anon.

    1993-01-01

    This chapter includes descriptions of electronic and mechanical components which do not merit a chapter to themselves. Other hardware requires mention because of particularly high tolerance or intolerance of exposure to radiation. A more systematic analysis of radiation responses of structures which are definable by material was given in section 3.8. The components discussed here are field effect transistors, transducers, temperature sensors, magnetic components, superconductors, mechanical sensors, and miscellaneous electronic components

  6. APS Storage Ring vacuum chamber fabrication

    International Nuclear Information System (INIS)

    Goeppner, G.A.

    1990-01-01

    The 1104-m circumference Advanced Photon Source Storage Ring Vacuum System is composed of 240 individual sections, which are fabricated from a combination of aluminum extrusions and machined components. The vacuum chambers will have 3800 weld joints, each subject to strict vacuum requirements, as well as a variety of related design criteria. The vacuum criteria and chamber design are reviewed, including a discussion of the weld joint geometries. The critical fabrication process parameters for meeting the design requirements are discussed. The experiences of the prototype chamber fabrication program are presented. Finally, the required facilities preparation for construction activity is briefly described. 6 refs., 6 figs., 1 tab

  7. Load-dependent Optimization of Honeycombs for Sandwich Components - New Possibilities by Using Additive Layer Manufacturing

    Science.gov (United States)

    Riss, Fabian; Schilp, Johannes; Reinhart, Gunther

    Due to their feasible geometric complexity, additive layer manufacturing (ALM) processes show a highpotential for the production of lightweight components.Therefore, ALM processes enable the realization of bionic-designedcomponents like honeycombs, which are optimized depending upon load and outer boundary conditions.This optimization is based on a closed-loop, three-steps methodology: At first, each honeycomb is conformed to the surface of the part. Secondly, the structure is optimizedfor lightweight design.It is possible to achieve a homogeneous stress distribution in the part by varying the wall thickness, honeycombdiameter and the amount of honeycombs, depending on the subjected stresses and strains. At last, the functional components like threads or bearing carriers are integrated directly into the honeycomb core.Using all these steps as an iterative process, it is possible to reduce the mass of sandwich components about 50 percent compared to conventional approaches.

  8. Photochemical cutting of fabrics

    Science.gov (United States)

    Piltch, Martin S.

    1994-01-01

    Apparatus for the cutting of garment patterns from one or more layers of fabric. A laser capable of producing laser light at an ultraviolet wavelength is utilized to shine light through a pattern, such as a holographic phase filter, and through a lens onto the one or more layers of fabric. The ultraviolet laser light causes rapid photochemical decomposition of the one or more layers of fabric, but only along the pattern. The balance of the fabric of the one or more layers of fabric is undamaged.

  9. Inkjet deposited circuit components

    Science.gov (United States)

    Bidoki, S. M.; Nouri, J.; Heidari, A. A.

    2010-05-01

    All-printed electronics as a means of achieving ultra-low-cost electronic circuits has attracted great interest in recent years. Inkjet printing is one of the most promising techniques by which the circuit components can be ultimately drawn (i.e. printed) onto the substrate in one step. Here, the inkjet printing technique was used to chemically deposit silver nanoparticles (10-200 nm) simply by ejection of silver nitrate and reducing solutions onto different substrates such as paper, PET plastic film and textile fabrics. The silver patterns were tested for their functionality to work as circuit components like conductor, resistor, capacitor and inductor. Different levels of conductivity were achieved simply by changing the printing sequence, inks ratio and concentration. The highest level of conductivity achieved by an office thermal inkjet printer (300 dpi) was 5.54 × 105 S m-1 on paper. Inkjet deposited capacitors could exhibit a capacitance of more than 1.5 nF (parallel plate 45 × 45 mm2) and induction coils displayed an inductance of around 400 µH (planar coil 10 cm in diameter). Comparison of electronic performance of inkjet deposited components to the performance of conventionally etched items makes the technique highly promising for fabricating different printed electronic devices.

  10. Electronic components

    CERN Document Server

    Colwell, Morris A

    1976-01-01

    Electronic Components provides a basic grounding in the practical aspects of using and selecting electronics components. The book describes the basic requirements needed to start practical work on electronic equipment, resistors and potentiometers, capacitance, and inductors and transformers. The text discusses semiconductor devices such as diodes, thyristors and triacs, transistors and heat sinks, logic and linear integrated circuits (I.C.s) and electromechanical devices. Common abbreviations applied to components are provided. Constructors and electronics engineers will find the book useful

  11. Component testing

    International Nuclear Information System (INIS)

    Hutchings, M.T.; Schofield, Peter; Seymour, W.A.J.

    1986-01-01

    A method for non-destructive testing of an industrial component to ascertain if it is a single crystal, and to find the crystal orientations of those parts of the component which are single crystals, involves irradiating the component with a monochromatic collimated neutron beam. Diffracted neutron beams are observed live by means of LiF/ZnS composite screen, an image intensifier and a television camera and screen. (author)

  12. Silicon Micromachining for Terahertz Component Development

    Science.gov (United States)

    Chattopadhyay, Goutam; Reck, Theodore J.; Jung-Kubiak, Cecile; Siles, Jose V.; Lee, Choonsup; Lin, Robert; Mehdi, Imran

    2013-01-01

    Waveguide component technology at terahertz frequencies has come of age in recent years. Essential components such as ortho-mode transducers (OMT), quadrature hybrids, filters, and others for high performance system development were either impossible to build or too difficult to fabricate with traditional machining techniques. With micromachining of silicon wafers coated with sputtered gold it is now possible to fabricate and test these waveguide components. Using a highly optimized Deep Reactive Ion Etching (DRIE) process, we are now able to fabricate silicon micromachined waveguide structures working beyond 1 THz. In this paper, we describe in detail our approach of design, fabrication, and measurement of silicon micromachined waveguide components and report the results of a 1 THz canonical E-plane filter.

  13. High-Thermal-Conductivity Fabrics

    Science.gov (United States)

    Chibante, L. P. Felipe

    2012-01-01

    Heat management with common textiles such as nylon and spandex is hindered by the poor thermal conductivity from the skin surface to cooling surfaces. This innovation showed marked improvement in thermal conductivity of the individual fibers and tubing, as well as components assembled from them. The problem is centered on improving the heat removal of the liquid-cooled ventilation garments (LCVGs) used by astronauts. The current design uses an extensive network of water-cooling tubes that introduces bulkiness and discomfort, and increases fatigue. Range of motion and ease of movement are affected as well. The current technology is the same as developed during the Apollo program of the 1960s. Tubing material is hand-threaded through a spandex/nylon mesh layer, in a series of loops throughout the torso and limbs such that there is close, form-fitting contact with the user. Usually, there is a nylon liner layer to improve comfort. Circulating water is chilled by an external heat exchanger (sublimator). The purpose of this innovation is to produce new LCVG components with improved thermal conductivity. This was addressed using nanocomposite engineering incorporating high-thermalconductivity nanoscale fillers in the fabric and tubing components. Specifically, carbon nanotubes were added using normal processing methods such as thermoplastic melt mixing (compounding twin screw extruder) and downstream processing (fiber spinning, tubing extrusion). Fibers were produced as yarns and woven into fabric cloths. The application of isotropic nanofillers can be modeled using a modified Nielsen Model for conductive fillers in a matrix based on Einstein s viscosity model. This is a drop-in technology with no additional equipment needed. The loading is limited by the ability to maintain adequate dispersion. Undispersed materials will plug filtering screens in processing equipment. Generally, the viscosity increases were acceptable, and allowed the filled polymers to still be

  14. Fabrics for aeronautic construction

    Science.gov (United States)

    Walen, E D

    1918-01-01

    The Bureau of Standards undertook the investigation of airplane fabrics with the view of finding suitable substitutes for the linen fabrics, and it was decided that the fibers to be considered were cotton, ramie, silk, and hemp. Of these, the cotton fiber was the logical one to be given primary consideration. Report presents the suitability, tensibility and stretching properties of cotton fabric obtained by laboratory tests.

  15. Fabricating architectural volume

    DEFF Research Database (Denmark)

    Feringa, Jelle; Søndergaard, Asbjørn

    2015-01-01

    The 2011 edition of Fabricate inspired a number of collaborations, this article seeks to highlight three of these. There is a common thread amongst the projects presented: sharing the ambition to close the rift between design and fabrication while incorporating structural design aspects early on....... The development of fabrication techniques in the work presented is considered an inherent part of architectural design and shares the aspiration of developing approaches to manufacturing architecture that are scalable to architectural proportions1 and of practical relevance....

  16. MAGNETIC WOVEN FABRICS - PHYSICAL AND MAGNETIC PROPERTIES

    Directory of Open Access Journals (Sweden)

    GROSU Marian C

    2015-05-01

    Full Text Available A coated material is a composite structure that consists of at least two components: base material and coating layer. The purpose of coating is to provide special properties to base material, with potential to be applied in EMI shielding and diverse smart technical fields. This paper reports the results of a study about some physical and magnetic properties of coated woven fabrics made from cotton yarns with fineness of 17 metric count. For this aim, a plain woven fabric was coated with a solution hard magnetic polymer based. As hard magnetic powder, barium hexaferrite (BaFe12O19 was selected. The plain woven fabric used as base has been coated with five solutions having different amounts of hard magnetic powder (15% - 45% in order to obtain five different magnetic woven fabrics. A comparison of physical properties regarding weight (g/m2, thickness (mm, degree of charging (% and magnetic properties of magnetic woven samples were presented. Saturation magnetizing (emu/g, residual magnetizing (emu/g and coercive force (kA/m of pure hard magnetic powder and woven fabrics have been studied as hysteresis characteristics. The magnetic properties of the woven fabrics depend on the mass percentage of magnetic powder from coating solution. Also, the residual magnetism and coercive field of woven fabrics represents only a part of bulk barium hexafferite residual magnetism and coercive field.

  17. Design, Construction, and Analysis of Fabric-Reinforced Embankment Test Section at Pinto Pass, Mobile, Alabama.

    Science.gov (United States)

    1981-10-01

    the nonwoven fabrics, it is used as a component of woven geotechnical fabrics, along with the pre- viously mentioned polyesters, polypropylenes , nylons...texture, and a relatively high permeability. 20 The synthetics such as polyester, polyamide (nylon), and polypropylene fibers used in nonwoven fabrics...of these particular applications, geotechnical fabrics are widely re- ferred to as " filter cloth." Most woven and nonwoven fabrics have an equivalent

  18. Bone formation: The rules for fabricating a composite ceramic

    Energy Technology Data Exchange (ETDEWEB)

    Caplan, A.I. (Case Western Reserve Univ., Cleveland, OH (USA))

    1990-01-01

    Bone, teeth and shells are complex composite ceramics which are fabricated at low temperature by living organisms. The detailed understanding of this fabrication process is required if we are to attempt to mimic this low temperature assembly process. The guiding principles and major components are outlined with the intent of establishing non-vital fabrication schemes to form a complex composite ceramic consisting of an organix matrix inorganic crystalline phase. 19 refs.

  19. Requirements for containment system components in CANDU nuclear power plants

    International Nuclear Information System (INIS)

    1988-02-01

    This Standard specifies the requirements and establishes the rules for design, fabrication, and installation of pressure-retaining containment system components. In this Standard the term 'components' includes non registered items

  20. Fabricating architectural volume

    DEFF Research Database (Denmark)

    Feringa, Jelle; Søndergaard, Asbjørn

    2015-01-01

    The 2011 edition of Fabricate inspired a number of collaborations, this article seeks to highlight three of these. There is a common thread amongst the projects presented: sharing the ambition to close the rift between design and fabrication while incorporating structural design aspects early on...

  1. Smart Fabrics Technology Development

    Science.gov (United States)

    Simon, Cory; Potter, Elliott; Potter, Elliott; McCabe, Mary; Baggerman, Clint

    2010-01-01

    Advances in Smart Fabrics technology are enabling an exciting array of new applications for NASA exploration missions, the biomedical community, and consumer electronics. This report summarizes the findings of a brief investigation into the state of the art and potential applications of smart fabrics to address challenges in human spaceflight.

  2. Sintering furnace for remote fuel fabrication

    International Nuclear Information System (INIS)

    Bowen, W.W.

    1978-10-01

    Component testing and evaluation of a chemical vapor deposition Re/W muffle has been initiated. Hydrogen permeation testing and thermal cycling behavior will be evaluated. Fabrication of prototype 10-12 Kg furnace is scheduled for completion late in 1979, at which time testing of the system will be initiated

  3. Impact damage in woven fabric reinforced composites

    NARCIS (Netherlands)

    Akkerman, Remko; Warnet, Laurent; van der Ven, E.C.

    2002-01-01

    Very often, woven fabrics are used as the reinforcement in advanced composite materials. Although the resulting inplane stiffness is lower than of their unidirectional counterparts, the excellent drapability of these materials eases the production of more general doubly curved components. In

  4. Reverse-symmetry waveguides: Theory and fabrication

    DEFF Research Database (Denmark)

    Horvath, R.; Lindvold, Lars René; Larsen, N.B.

    2002-01-01

    We present an extensive theoretical analysis of reverse-symmetry waveguides with special focus on their potential application as sensor components in aqueous media and demonstrate a novel method for fabrication of such waveguides. The principle of reverse symmetry is based on making the refractive...

  5. Design and fabrication of a multipurpose railroad hand truck ...

    African Journals Online (AJOL)

    A multipurpose railroad hand truck comprising mainly of a frame, swinger arm, connecting rod, crank shaft, gears, wheels and brake was designed and fabricated to reduce the cost of material handling in small scaled manufacturing industries. The frame and other major components of the hand truck were fabricated with ...

  6. Novel Amalgams for In-Space Parts Fabrication

    Science.gov (United States)

    Cochran, Calvin; VanHoose, James R.; Grugel, Richard N.

    2012-01-01

    Sound amalgams can be fabricated by substituting Ga-In liquid for mercury; Cu-coated steel fibers bond well with the amalgam components. Inclusion of steel fibers significantly improved mechanical properties. An application scenario utilizing amalgams for in-space parts fabrication and repair was suggested. Procedure and materials need to be optimized

  7. Fabrics in Function

    DEFF Research Database (Denmark)

    Bang, Anne Louise

    2007-01-01

    to the establishment of an initial framework for the project it has a focus on how to explore costumers and users emotional experiences with fabrics. The three year research project is based on experimental design research and the textile designer's competences and knowledge. During the research project exploring...... sensing of fabrics in function. It is proposed that tactile and visual sensing of fabrics is a way to investigate and express emotional utility values. The further purpose is to use experiments with repertory grid models as part of the mapping of the entire research project and also as a basis...

  8. Component Rhinoplasty

    OpenAIRE

    Mohmand, Muhammad Humayun; Ahmad, Muhammad

    2014-01-01

    BACKGROUND According to statistics of American Society of Plastic Surgeons, cosmetic rhinoplasty was the second most frequently performed cosmetic surgery. This study shares the experiences with component rhinoplasty. METHODS From 2004 to 2010, all patients underwent aesthetic nasal surgery were enrolled. The patients requiring only correction of septal deviation and those presenting with cleft lip nasal deformity were excluded. All procedures were performed under general anaesthesia with ope...

  9. Hyperfrequency components

    Science.gov (United States)

    1994-09-01

    The document has a collection of 19 papers (11 on technologies, 8 on applications) by 26 authors and coauthors. Technological topics include: evolution from conventional HEMT's double heterojunction and planar types of pseudomorphic HEMT's; MMIC R&D and production aspects for very-low-noise, low-power, and very-low-noise, high-power applications; hyperfrequency CAD tools; parametric measurements of hyperfrequency components on plug-in cards for design and in-process testing uses; design of Class B power amplifiers and millimetric-wave, bigrid-transistor mixers, exemplifying combined use of three major types of physical simulation in electrical modeling of microwave components; FET's for power amplification at up to 110 GHz; production, characterization, and nonlinear applications of resonant tunnel diodes. Applications topics include: development of active modules for major European programs; tubes versus solid-state components in hyperfrequency applications; status and potentialities of national and international cooperative R&D on MMIC's and CAD of hyperfrequency circuitry; attainable performance levels in multifunction MMIC applications; state of the art relative of MESFET power amplifiers (Bands S, C, X, Ku); creating a hyperfrequency functions library, of parametrizable reference cells or macrocells; and design of a single-stage, low-noise, band-W amplifier toward development of a three-stage amplifier.

  10. Experimental Fabrication Facility

    Data.gov (United States)

    Federal Laboratory Consortium — Provides aviation fabrication support to special operations aircraft residing at Fort Eustis and other bases in the United States. Support is also provided to AATD...

  11. Alloy Fabrication Laboratory

    Data.gov (United States)

    Federal Laboratory Consortium — At NETL’s Alloy Fabrication Facility in Albany, OR, researchers conduct DOE research projects to produce new alloys suited to a variety of applications, from gas...

  12. Variance Components

    CERN Document Server

    Searle, Shayle R; McCulloch, Charles E

    1992-01-01

    WILEY-INTERSCIENCE PAPERBACK SERIES. The Wiley-Interscience Paperback Series consists of selected books that have been made more accessible to consumers in an effort to increase global appeal and general circulation. With these new unabridged softcover volumes, Wiley hopes to extend the lives of these works by making them available to future generations of statisticians, mathematicians, and scientists. ". . .Variance Components is an excellent book. It is organized and well written, and provides many references to a variety of topics. I recommend it to anyone with interest in linear models.".

  13. DESIGN AND FABRICATION OF MICRONOZZLES

    Directory of Open Access Journals (Sweden)

    Kean How Cheah

    2011-05-01

    Full Text Available Normal 0 false false false EN-US ZH-CN X-NONE MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-fareast-font-family:SimSun; mso-fareast-theme-font:minor-fareast; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin; mso-bidi-font-family:"Times New Roman"; mso-bidi-theme-font:minor-bidi;} Micronozzle, a key component in micropropulsion system, has been designed and fabricated. Quasi 1D inviscid theory was used in designing a series of conical micronozzles of different expander half-angles (10°-50°. Aerospike micronozzle, a promising candidate to achieve high performance propulsion system, was designed with Angelino method (or Approximate method. Both micronozzles were fabricated using soft lithography, an inexpensive and relatively simple technique comparing to well-established deep reactive ion etching (DRIE technique, with polydimethylsiloxane (PDMS as structural material. Micronozzles with two different nozzle throat width, 53.5µm and 107µm, were fabricated for comparison. Microscopic inspections reveal 107µm is the more producible nozzle throat width with current equipments. The PDMS-based micronozzle can be used as cold gas microthruster system for micro- and nanosatellites.

  14. Ageing of zirconium alloy components

    Science.gov (United States)

    Chatterjee, S.; Shah, Priti Kotak; Dubey, J. S.

    2008-12-01

    India has two types (pressurized heavy water reactors (PHWRs) and boiling water reactors (BWRs)) of commercial nuclear reactors in operation, in addition to research reactors. Many of the life limiting critical components in these reactors are fabricated from zirconium alloys. The progressive degradation of these components caused by the cumulative exposure of high energy neutron irradiation with increasing period of reactor operation was monitored to assess the degree of ageing. The components/specimens examined included fuel element claddings removed from BWRs, pressure tubes and garter springs removed from PHWRs and calandria tube specimens used in PHWRs. The tests included tension test (for cladding, garter spring), fracture toughness test (for pressure tube), crush test (for garter spring), and measurement of irradiation induced growth (for calandria tube). Results of various tests conducted are presented and applications of the test results are elaborated for residual life estimation/life extension of the components.

  15. ATLAS facility fabrication and assembly

    CERN Document Server

    Ballard, E O; Davis, H A; Nielsen, K E; Parker, G V; Parsons, W M

    2001-01-01

    Summary form only given. Atlas is a pulsed-power facility recently completed at Los Alamos National Laboratory to drive hydrodynamic experiments. This new generation pulsed-power machine consists of a radial array of 24, 240-kV Marx modules and transmission lines supplying current to the load region at the machine center. The transmission lines, powered by the Marx modules, consist of cable headers, load protection switches and tri-plates interfacing to the center transition section through detachable current joints. A conical power-flow-channel attaches to the transition section providing an elevated interface to attach the experimental loads for diagnostic access. Fabrication and assembly of all components for the Atlas machine was completed in August 2000. The machine has also progressed through a test phase where the Marx module/transmission line units were fired, individually, into a test load. Progression continued with eight and sixteen lines being fired. Subsequently, an overall machine test was condu...

  16. Understanding core conductor fabrics

    International Nuclear Information System (INIS)

    Swenson, D E

    2011-01-01

    ESD Association standard test method ANSI/ESD STM2.1 - Garments (STM2.1), provides electrical resistance test procedures that are applicable for materials and garments that have surface conductive or surface dissipative properties. As has been reported in other papers over the past several years 1 fabrics are now used in many industries for electrostatic control purposes that do not have surface conductive properties and therefore cannot be evaluated using the procedures in STM2.1 2 . A study was conducted to compare surface conductive fabrics with samples of core conductor fibre based fabrics in order to determine differences and similarities with regards to various electrostatic properties. This work will be used to establish a new work item proposal within WG-2, Garments, in the ESD Association Standards Committee in the USA.

  17. Determining glacier flow direction from till fabrics

    Science.gov (United States)

    Iverson, Neal R.

    2017-12-01

    Field and experimental data indicate that fabrics of sheared basal tills, based on particle orientations and on anisotropy of magnetic susceptibility, are inclined relative to the macroscopic plane of shear. As a result, if this plane is tilted with a transverse component, one of the longest-standing axioms of glacial geology-that particles in basal till are preferentially oriented parallel to the direction of shear-is not strictly true. The resultant correction to the shearing direction increases with the transverse and longitudinal components of shear-plane inclination and with the magnitude of the fabric inclination relative to the shear plane. Azimuthal corrections calculated herein range from being negligible to a few tens of degrees for reasonable ranges of shear-plane tilt. The past success of fabric azimuths as indicators of flow direction, despite the absence of this correction, likely reflects the clustering of shear planes about the horizontal in basal tills. However, on the flanks of accreting subglacial bedforms, shear-plane attitudes may well conform to the local bedform slope. As illustrated with hypothetical fabrics of drumlins and flutes, azimuthal corrections can in that case be sufficiently large and systematic to seriously affect interpretations of bedform genesis.

  18. MOX Fabrication Isolation Considerations

    Energy Technology Data Exchange (ETDEWEB)

    Eric L. Shaber; Bradley J Schrader

    2005-08-01

    This document provides a technical position on the preferred level of isolation to fabricate demonstration quantities of mixed oxide transmutation fuels. The Advanced Fuel Cycle Initiative should design and construct automated glovebox fabrication lines for this purpose. This level of isolation adequately protects the health and safety of workers and the general public for all mixed oxide (and other transmutation fuel) manufacturing efforts while retaining flexibility, allowing parallel development and setup, and minimizing capital expense. The basis regulations, issues, and advantages/disadvantages of five potential forms of isolation are summarized here as justification for selection of the preferred technical position.

  19. Methods for fabrication of flexible hybrid electronics

    Science.gov (United States)

    Street, Robert A.; Mei, Ping; Krusor, Brent; Ready, Steve E.; Zhang, Yong; Schwartz, David E.; Pierre, Adrien; Doris, Sean E.; Russo, Beverly; Kor, Siv; Veres, Janos

    2017-08-01

    Printed and flexible hybrid electronics is an emerging technology with potential applications in smart labels, wearable electronics, soft robotics, and prosthetics. Printed solution-based materials are compatible with plastic film substrates that are flexible, soft, and stretchable, thus enabling conformal integration with non-planar objects. In addition, manufacturing by printing is scalable to large areas and is amenable to low-cost sheet-fed and roll-to-roll processes. FHE includes display and sensory components to interface with users and environments. On the system level, devices also require electronic circuits for power, memory, signal conditioning, and communications. Those electronic components can be integrated onto a flexible substrate by either assembly or printing. PARC has developed systems and processes for realizing both approaches. This talk presents fabrication methods with an emphasis on techniques recently developed for the assembly of off-the-shelf chips. A few examples of systems fabricated with this approach are also described.

  20. First wall/blanket fabrication technology

    International Nuclear Information System (INIS)

    Mohri, Kensuke; Yamazaki, Seiichiro; Kobayashi, Takeshi; Yamada, Takeshi; Akiba, Masato; Seki, Masahiro.

    1991-01-01

    In a fusion nuclear reactor, armor is required to protect the in-vessel components from the plasma energy. In many first wall armor concepts, a radiative cooled armor tile first wall is proposed as one of the candidate structure for the first wall components, characterized by a central mechanical attachment, a thermally insulated mount, remote-handling capability and simplicity. In this paper, R and D results on the fabrication of first wall panel with two Hot Isostatic Pressing (HIP) bonding techniques, i.e. grooved plate type technique and rectangular tube one, and on the fabrication of first wall panel with radiative cooled graphite armor tile are described. A thermal-analysis and stress-analysis for this first wall panel with radiative cooled graphite armor tile are also studied. (author)

  1. Feasibility Study of Laser Cutting for Fabrication of Tensile Specimen

    International Nuclear Information System (INIS)

    Jin, Y. G.; Baik, S. J.; Kim, G. S.; Heo, G. S.; Yoo, B. O.; Ahn, S. B.; Chun, Y. B.

    2015-01-01

    The specimen fabrication technique was established to machine the specimen from the irradiated materials. The wire cut EDM(electric discharge machine) was modified to fabricate the mechanical testing specimens from irradiated components and fuel claddings. The oxide layer removal system was also developed because the oxide layer on the surface of the irradiated components and claddings interrupted the applying the electric current during the processing. However, zirconium oxide is protective against further corrosion as well as beneficial to mechanical strength for the tensile deformation of the cladding. Thus, it is important to fabricate the irradiated specimens without removal of oxide layer on the surface of the irradiated structural components and claddings. In the present study, laser cutting system was introduced to fabricate the various mechanical testing specimens from the unirradiated fuel cladding and the feasibility of the laser cutting system was studied for the fabrication of various types of irradiated specimens in a hot cell at IMEF (Irradiated Materials Examination Facility) of KAERI. Laser beam machining system was introduced to fabricate the various mechanical testing specimens from the unirradiated fuel cladding and the dimensions were compared for the feasibility of the laser cutting system. The effect of surface oxide layer was also investigated for machining process of the zircaloy-4 fuel cladding and it was found that laser beam machining could be a useful tool to fabricate the specimens with surface oxide layer

  2. Pigmi mechanical fabrication

    International Nuclear Information System (INIS)

    Hart, V.E.

    1976-01-01

    A prime goal of the mechanical design effort associated with the PIGMI (Pion Generator for Medical Irradiations) program is to investigate new materials and fabrication techniques in an effort to obtain increased machine efficiency and reliability at a reasonable cost. A discussion is given dealing with the modeling program that LASL is pursuing for 450-MHz and 1350-MHz PIGMI development

  3. PIGMI mechanical fabrication

    International Nuclear Information System (INIS)

    Hart, V.E.

    1976-01-01

    A prime goal of the mechanical design effort associated with the PIGMI (Pion Generator for Medical Irradiations) program is to investigate new materials and fabrication techniques in an effort to obtain increased machine efficiency and reliability at a reasonable cost. The following discussion deals with the modeling program that LASL is pursuing for 450-MHz and 1350-MHz PIGMI development. (author)

  4. Fabrication activity for nanophotonics

    DEFF Research Database (Denmark)

    Malureanu, Radu; Chung, Il-Sug; Carletti, Luca

    We present the fabrication and characterization of new structures and materials to be used in nanophotonics. The first structure presented is a fractal metallic metasurface designed to be used as a high-sensitivity sensor for 810nm wavelength. A second structure is a high index contrast grating...

  5. Alkali semi-metal films and method and apparatus for fabricating them

    Energy Technology Data Exchange (ETDEWEB)

    Bhandari, Harish B.; Nagarkar, Vivek V.; Ovechkina, Olena E.; Frisch, Henry J.; Attenkofer, Klaus; Smedley, John M.

    2018-03-13

    Methods and systems for fabricating a film, such as, for example, a photocathode, having a tailored band structure and thin-film components that can be tailored for specific applications, such as, for example photocathode having a high quantum efficiency, and simple components fabricated by those methods.

  6. A Wear Geometry Model of Plain Woven Fabric Composites

    Directory of Open Access Journals (Sweden)

    Gu Dapeng

    2014-09-01

    Full Text Available The paper g describes a model meant for analysis of the wear geometry of plain woven fabric composites. The referred model consists of a mathematical description of plain woven fabric based on Peirce’s model coupled with a stratified method for the solution of the wear geometry. The evolutions of the wear area ratio of weft yarn, warp yarn and matrix resin on the worn surface are simulated by MatLab software in combination of warp and weft yarn diameters, warp and weft yarn-to-yarn distances, fabric structure phases (SPs. By comparing theoretical and experimental results from the PTFE/Kevlar fabric wear experiment, it can be concluded that the model can present a trend of the component area ratio variations along with the thickness of fabric, but has a inherently large error in quantitative analysis as an idealized model.

  7. True and intentionally fabricated memories

    OpenAIRE

    Justice, L.V.; Morrison, C.M.; Conway, M. A.

    2012-01-01

    The aim of the experiment reported here was to investigate the processes underlying the construction of truthful and deliberately fabricated memories. Properties of memories created to be intentionally false - fabricated memories - were compared to properties of memories believed to be true - true memories. Participants recalled and then wrote or spoke true memories and fabricated memories of everyday events. It was found that true memories were reliably more vivid than fabricated memories an...

  8. Fabrication of Nanochannels

    Directory of Open Access Journals (Sweden)

    Yuqi Zhang

    2015-09-01

    Full Text Available Nature has inspired the fabrication of intelligent devices to meet the needs of the advanced community and better understand the imitation of biology. As a biomimetic nanodevice, nanochannels/nanopores aroused increasing interest because of their potential applications in nanofluidic fields. In this review, we have summarized some recent results mainly focused on the design and fabrication of one-dimensional nanochannels, which can be made of many materials, including polymers, inorganics, biotic materials, and composite materials. These nanochannels have some properties similar to biological channels, such as selectivity, voltage-dependent current fluctuations, ionic rectification current and ionic gating, etc. Therefore, they show great potential for the fields of biosensing, filtration, and energy conversions. These advances can not only help people to understand the living processes in nature, but also inspire scientists to develop novel nanodevices with better performance for mankind.

  9. Automated breeder fuel fabrication

    International Nuclear Information System (INIS)

    Goldmann, L.H.; Frederickson, J.R.

    1983-01-01

    The objective of the Secure Automated Fabrication (SAF) Project is to develop remotely operated equipment for the processing and manufacturing of breeder reactor fuel pins. The SAF line will be installed in the Fuels and Materials Examination Facility (FMEF). The FMEF is presently under construction at the Department of Energy's (DOE) Hanford site near Richland, Washington, and is operated by the Westinghouse Hanford Company (WHC). The fabrication and support systems of the SAF line are designed for computer-controlled operation from a centralized control room. Remote and automated fuel fabriction operations will result in: reduced radiation exposure to workers; enhanced safeguards; improved product quality; near real-time accountability, and increased productivity. The present schedule calls for installation of SAF line equipment in the FMEF beginning in 1984, with qualifying runs starting in 1986 and production commencing in 1987. 5 figures

  10. Intentionally fabricated autobiographical memories

    OpenAIRE

    Justice, LV; Morrison, CM; Conway, MA

    2017-01-01

    Participants generated both autobiographical memories (AMs) that they believed to be true and intentionally fabricated autobiographical memories (IFAMs). Memories were constructed while a concurrent memory load (random 8-digit sequence) was held in mind or while there was no concurrent load. Amount and accuracy of recall of the concurrent memory load was reliably poorer following generation of IFAMs than following generation of AMs. There was no reliable effect of load on memory generation ti...

  11. Fabrication of nuclear fuel

    International Nuclear Information System (INIS)

    Ion, S.E.; Watson, R.H.; Loch, E.P.

    1989-01-01

    Commercial nuclear fuel fabrication is focused on providing quality products. Throughout manufacturing attention is placed on the precise control of processes, procedures and tooling to reduce product variability. This paper describes the processes used to manufacture fuel for the advanced gas cooled reactor, light water reactor, fast breeder reactor and Magnox reactor systems at the BNFL, Springfields, and Westinghouse Columbia, USA, facilities. It covers the chemical purification and conversion stages of fuel production before describing the fabrication of both oxide and metallic fuel and gives a general overview of the technology used. Although the principles of fuel fabrication in terms of providing a cladding designed to be the primary envelope to encase the fuel are similar for each system, there are detailed differences in manufacturing route and cladding type which arise from differing reactor requirements. These, together with developments made in response to customer needs, are reviewed and the need to maintain a high purity reliable product with low variability at all stages in manufacture is emphasized throughout. (author)

  12. Advanced fuel fabrication

    International Nuclear Information System (INIS)

    Bernard, H.

    1989-01-01

    This paper deals with the fabrication of advanced fuels, such as mixed oxides for Pressurized Water Reactors or mixed nitrides for Fast Breeder Reactors. Although an extensive production experience exists for the mixed oxides used in the FBR, important work is still needed to improve the theoretical and technical knowledge of the production route which will be introduced in the future European facility, named Melox, at Marcoule. Recently, the feasibility of nitride fuel fabrication in existing commercial oxide facilities was demonstrated in France. The process, based on carbothermic reduction of oxides with subsequent comminution of the reaction product, cold pressing and sintering provides (U, Pu)N pellets with characteristics suitable for irradiation testing. Two experiments named NIMPHE 1 and 2 fabricated in collaboration with ITU, Karlsruhe, involve 16 nitride and 2 carbide pins, operating at a linear power of 45 and 73 kW/m with a smear density of 75-80% TD and a high burn-up target of 15 at%. These experiments are currently being irradiated in Phenix, at Marcoule. (orig.)

  13. Design and Fabrication of a Free-Form Reciprocal Roof

    DEFF Research Database (Denmark)

    Parigi, Dario

    2015-01-01

    of relations between design parameters and a wide array of measurable performances. Due to the reciprocal structures geometric complexity, the shape generation process is handled using the Reciprocalizer, a software tool developed by the author that embeds in a computational environment the constructional...

  14. Elongation of fibers from highly viscous dextran solutions enables fabrication of rapidly dissolving drug carrying fabrics.

    Science.gov (United States)

    Frampton, John P; Lai, David; Lounds, Maxwell; Chung, Kyeongwoon; Kim, Jinsang; Mansfield, John F; Takayama, Shuichi

    2015-01-28

    A simple method is presented for forming thread-like fibers from highly viscous dextran solutions. Based on the cohesive and adhesive forces between a dextran solution and the substrate to which it is applied, multiple fibers of approximately 10 μm in diameter can be elongated simultaneously. These fibers can be woven into multiple layers to produce fabrics of varying fiber orientations and mechanical properties. Various bioactive agents can be incorporated into the dextran solution prior to fiber formation, including hemostatic and antibiotic agents. Fabrics containing thrombin are capable of coagulating human platelet poor plasma in vitro. Fabrics containing antibiotics are capable of suppressing bacterial growth in a disk diffusion assay. These data suggest that this new material composed entirely of dextran has promise as a drug delivery component in wound dressings. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  15. Electrochemical components employing polysiloxane-derived binders

    Science.gov (United States)

    Delnick, Frank M.

    2013-06-11

    A processed polysiloxane resin binder for use in electrochemical components and the method for fabricating components with the binder. The binder comprises processed polysiloxane resin that is partially oxidized and retains some of its methyl groups following partial oxidation. The binder is suitable for use in electrodes of various types, separators in electrochemical devices, primary lithium batteries, electrolytic capacitors, electrochemical capacitors, fuel cells and sensors.

  16. Rapid Manufacturing of High Power Electric Propulsion Components, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — A flexible, lower cost approach to the rapid manufacture of high power electric propulsion components is desirable. Today's near-net fabrication technologies are...

  17. Dissolvable microneedle fabrication using piezoelectric dispensing technology.

    Science.gov (United States)

    Allen, Evin A; O'Mahony, Conor; Cronin, Michael; O'Mahony, Thomas; Moore, Anne C; Crean, Abina M

    2016-03-16

    Dissolvable microneedle (DMN) patches are novel dosage forms for the percutaneous delivery of vaccines. DMN are routinely fabricated by dispensing liquid formulations into microneedle-shaped moulds. The liquid formulation within the mould is then dried to create dissolvable vaccine-loaded microneedles. The precision of the dispensing process is critical to the control of formulation volume loaded into each dissolvable microneedle structure. The dispensing process employed must maintain vaccine integrity. Wetting of mould surfaces by the dispensed formulation is also an important consideration for the fabrication of sharp-tipped DMN. Sharp-tipped DMN are essential for ease of percutaneous administration. In this paper, we demonstrate the ability of a piezoelectric dispensing system to dispense picolitre formulation volumes into PDMS moulds enabling the fabrication of bilayer DMN. The influence of formulation components (trehalose and polyvinyl alcohol (PVA) content) and piezoelectric actuation parameters (voltage, frequency and back pressure) on drop formation is described. The biological integrity of a seasonal influenza vaccine following dispensing was investigated and maintained voltage settings of 30 V but undermined at higher settings, 50 and 80 V. The results demonstrate the capability of piezoelectric dispensing technology to precisely fabricate bilayer DMN. They also highlight the importance of identifying formulation and actuation parameters to ensure controlled droplet formulation and vaccine stabilisation. Copyright © 2015 Elsevier B.V. All rights reserved.

  18. Magnetic and shape fabrics of magnetite in simple shear flows

    Science.gov (United States)

    Arbaret, Laurent; Launeau, Patrick; Diot, Hervé; Sizaret, Stanislas

    2013-01-01

    The magnetite fabrics measured by anisotropy of magnetic susceptibility (AMS) and by shape preferred orientation (SPO) optical methods are classically used as flow kinematics indicators in lava flows. The development of magnetite fabrics during simple shear strains γ ≤ 20 was performed using a suspension of 1% volume fraction of multidomain magnetite randomly contained in a mixture of silicone and wax. We measured AMS fabric and SPO ellipsoids by calculating a quadratic shape tensor from oriented thin-sections. For γ 8, fabric elements, foliation and lineation, are stabilised closely parallel to the flow plane and the shear direction, respectively. Two- and three-dimensional numerical simulations using measured aspect ratios of magnetite point out that the large scattering of aspect ratios and the initial orientation distribution of particles are together responsible for a wide-ranging loss of periodicity. The stable AMS and SPO fabrics observed at large strains in experiments are the result of these primary fabric properties combined to collisions between particles and, possibly, their complex three-dimensional shapes. In addition, the constant angular relationship observed at large strains between fabrics and flow components is related to the transient collisions. Consequently, the determination of the lava flow kinematics by using fabric properties measured either by AMS or by SPO analyses should be indubitably associated to a detailed study of the three-dimensional shape of the solid carriers. Regularly shaped populations of low elongated particles will be capable to produce cyclic to oscillating fabrics, while the fabric of elongated particles will be more sensitive to the shape parameters and collisions, ultimately favouring stable fabrics at large strains.

  19. Optical communication components

    Science.gov (United States)

    Eldada, Louay

    2004-03-01

    We review and contrast key technologies developed to address the optical components market for communication applications. We first review the component requirements from a network perspective. We then look at different material systems, compare their properties, and describe the functions achieved to date in each of them. The material systems reviewed include silica fiber, silica on silicon, silicon on insulator, silicon oxynitride, sol-gels, polymers, thin-film dielectrics, lithium niobate, indium phosphide, gallium arsenide, magneto-optic materials, and birefringent crystals. We then describe the most commonly used classes of optical device technology and present their pros and cons as well as the functions achieved to date in each of them. The technologies reviewed include passive, actuation, and active technologies. The passive technologies described include fused fibers, dispersion-compensating fiber, beam steering, Bragg gratings, diffraction gratings, holographic elements, thin-film filters, photonic crystals, microrings, and birefringent elements. The actuation technologies include thermo-optics, electro-optics, acousto-optics, magneto-optics, electroabsorption, liquid crystals, total internal reflection technologies, and mechanical actuation. The active technologies include heterostructures, quantum wells, rare-earth doping, dye doping, Raman amplification, and semiconductor amplification. We also investigate the use of different material systems and device technologies to achieve building-block functions, including lasers, amplifiers, detectors, modulators, polarization controllers, couplers, filters, switches, attenuators, isolators, circulators, wavelength converters, chromatic dispersion compensators, and polarization mode dispersion compensators. Some of the technologies presented are well established in the industry and in some cases have reached the commodity stage, others have recently become ready for commercial introduction, while some others

  20. Numerical and Experimental Study of Ti6Al4V Components Manufactured Using Powder Bed Fusion Additive Manufacturing

    Science.gov (United States)

    Zielinski, Jonas; Mindt, Hans-Wilfried; Düchting, Jan; Schleifenbaum, Johannes Henrich; Megahed, Mustafa

    2017-12-01

    Powder bed fusion additive manufacturing of titanium alloys is an interesting manufacturing route for many applications requiring high material strength combined with geometric complexity. Managing powder bed fusion challenges, including porosity, surface finish, distortions and residual stresses of as-built material, is the key to bringing the advantages of this process to production main stream. This paper discusses the application of experimental and numerical analysis towards optimizing the manufacturing process of a demonstration component. Powder characterization including assessment of the reusability, assessment of material consolidation and process window optimization is pursued prior to applying the identified optima to study the distortion and residual stresses of the demonstrator. Comparisons of numerical predictions with measurements show good correlations along the complete numerical chain.

  1. Mask fabrication process

    Science.gov (United States)

    Cardinale, Gregory F.

    2000-01-01

    A method for fabricating masks and reticles useful for projection lithography systems. An absorber layer is conventionally patterned using a pattern and etch process. Following the step of patterning, the entire surface of the remaining top patterning photoresist layer as well as that portion of an underlying protective photoresist layer where absorber material has been etched away is exposed to UV radiation. The UV-exposed regions of the protective photoresist layer and the top patterning photoresist layer are then removed by solution development, thereby eliminating the need for an oxygen plasma etch and strip and chances for damaging the surface of the substrate or coatings.

  2. Design and fabrication of miniature combination lock

    International Nuclear Information System (INIS)

    Yang Gao; Wei Su

    2006-01-01

    Design and fabrication of a miniature combination lock is reported. The prototype's outline size is less than 15mm x 20mm x 25mm, with the function of 24 steps single-try discrimination. Two miniature application-specific electromagnetic motors are used to drive a counter meshing gears (CMG) mechanism. Ratchet-pawl mechanism is respectively attached to each CMG gears assembly, to insure it step forward at accurate angles in company with motor driving circuit. Main functional components of the lock are fabricated by UV-LIGA micromachining process, including the motor's stator with 4-level planar coils. Handcraft assembling process and control circuit design are also briefly introduced. The prototype had already endured more than 1000 times of unlocking and 100 times of manually unlocking. It is proved that micro-motor and micromachining technologies are very useful in miniaturization of such a surety device

  3. Reforming Shapes for Material-aware Fabrication

    KAUST Repository

    Yang, Yongliang

    2015-08-10

    © 2015 The Eurographics Association and John Wiley & Sons Ltd. Published by John Wiley & Sons Ltd. As humans, we regularly associate shape of an object with its built material. In the context of geometric modeling, however, this inter-relation between form and material is rarely explored. In this work, we propose a novel data-driven reforming (i.e.; reshaping) algorithm that adapts an input multi-component model for a target fabrication material. The algorithm adapts both the part geometry and the inter-part topology of the input shape to better align with material-aware fabrication requirements. As output, we produce the reshaped model along with respective part dimensions and inter-part junction specifications. We evaluate our algorithm on a range of man-made models and demonstrate a variety of model reshaping examples focusing only on metal and wooden materials.

  4. 2k micro moulding for MID fabrication

    DEFF Research Database (Denmark)

    Islam, Aminul; Hansen, Hans Nørgaard; Jørgensen, Martin Bondo

    2009-01-01

    Molded Interconnect Devices (MIDs) are plastic substrates with electrical infrastructure. The fabrication of MIDs is usually based on injection molding and different process chains may be identified from this starting point. The use of MIDs has been driven primarily by the automotive sector......, but recently the medical sector seems more and more interested. In particular, the possibility of miniaturization of 3D components with electrical infrastructure is attractive. The paper describes possible manufacturing routes and challenges of miniaturized MIDs based on two component injection molding...... and subsequent metallization. This technology promises cost-effective and convergent manufacturing approaches for both macro and micro applications. This paper presents the results of industrial MID production based on two component injection molding and discusses the important issues for MID production that can...

  5. Fabrication of zein nanostructure

    Science.gov (United States)

    Luecha, Jarupat

    The concerns on the increase of polluting plastic wastes as well as the U.S. dependence on imported petrochemical products have driven an attention towards alternative biodegradable polymers from renewable resources. Zein protein, a co-product from ethanol production from corn, is a good candidate. This research project aims to increase zein value by adopting nanotechnology for fabricating advanced zein packaging films and zein microfluidic devices. Two nanotechnology approaches were focused: the polymer nanoclay nanocomposite technique where the nanocomposite structures were created in the zein matrix, and the soft lithography and the microfluidic devices where the micro and nanopatterns were created on the zein film surfaces. The polymer nanoclay nanocomposite technique was adopted in the commonly used zein film fabrication processes which were solvent casting and extrusion blowing methods. The two methods resulted in partially exfoliated nanocomposite structures. The impact of nanoclays on the physical properties of zein films strongly depended on the film preparation techniques. The impact of nanoclay concentration was more pronounced in the films made by extrusion blowing technique than by the solvent casting technique. As the processability limitation for the extrusion blowing technique of the zein sample containing hight nanoclay content, the effect of the nanoclay content on the rheological properties of zein hybrid resins at linear and nonlinear viscoelastic regions were further investigated. A pristine zein resin exhibited soft solid like behavior. On the other hand, the zein hybrid with nanoclay content greater than 5 wt.% showed more liquid like behavior, suggesting that the nanoclays interrupted the entangled zein network. There was good correspondence between the experimental data and the predictions of the Wagner model for the pristine zein resins. However, the model failed to predict the steady shear properties of the zein nanoclay nanocomposite

  6. AFIP-6 Fabrication Summary Report

    Energy Technology Data Exchange (ETDEWEB)

    Glenn A. Moore; M. Craig Marshall

    2011-09-01

    The AFIP-6 (ATR Full-size plate In center flux trap Position) experiment was designed to evaluate the performance of monolithic fuels at a scale prototypic of research reactor fuel plates. Two qualified fueled plates were fabricated for the AFIP-6 experiment; to be irradiated in the INL Advanced Test Reactor (ATR). This report provides details of the fuel fabrication efforts, including material selection, fabrication processes, and fuel plate qualification.

  7. Filter Fabrics for Airport Drainage.

    Science.gov (United States)

    1979-09-01

    pneumatically filling a woven polypropylene stocking with sand and vibrating it into a prebored hole, while another method uses a polyester nonwoven fabric...Selected Nonwoven Filter Fabrics," Letter Report, June 1977, U. S. Army Engineer Waterways Experiment Station, CE, Vicksburg, Miss. 18. BalL, J. E...woven and nonwoven plastic filter fabric. It has been developed based on limited field performance observations and the laboratory test evaluation of

  8. Solid freeform fabrication of biological materials

    Science.gov (United States)

    Wang, Jiwen

    This thesis investigates solid freeform fabrication of biological materials for dental restoration and orthopedic implant applications. The basic approach in this study for solid freeform fabrication of biological materials is micro-extrusion of single or multiple slurries for 3D components and inkjet color printing of multiple suspensions for functionally graded materials (FGMs). Common issues associated with micro-extrusion and inkjet color printing are investigated. These common issues include (i) formulation of stable slurries with a pseudoplastic property, (ii) cross-sectional geometry of the extrudate as a function of the extrusion parameters, (iii) fabrication path optimization for extrusion process, (iv) extrusion optimization for multi-layer components, (v) composition control in functionally graded materials, and (vi) sintering optimization to convert the freeform fabricated powder compact to a dense body for biological applications. The present study clearly shows that the rheological and extrusion behavior of dental porcelain slurries depend strongly on the pH value of the slurry and extrusion conditions. A slurry with pseudoplastic properties is a basic requirement for obtaining extruded lines with rectangular cross-sections. The cross-sectional geometry of the extrudate is also strongly affected by extrusion parameters including the extrusion nozzle height, nozzle moving speed, extrusion rate, and critical nozzle height. Proper combinations of these extrusion parameters are necessary in order to obtain single line extrudates with near rectangular cross-sections and 3D objects with dimensional accuracy, uniform wall thickness, good wall uprightness, and no wall slumping. Based on these understandings, single-wall, multi-wall, and solid teeth have been fabricated via micro-extrusion of the dental slurry directly from a CAD digital model in 30 min. Inkjet color printing using stable Al2O3 and ZrO 2 aqueous suspensions has been developed to fabricate

  9. Ultraviolet Protection by Fabric Engineering

    Directory of Open Access Journals (Sweden)

    Mukesh Kumar Singh

    2013-01-01

    Full Text Available Background. The increasing emission of greenhouse gases has evoked the human being to save the ozone layer and minimize the risk of ultraviolet radiation (UVR. Various fabric structures have been explored to achieve desired ultraviolet protection factor (UPF in various situations. Objective. In this study, the effect of various filament configurations like twisted, flat, intermingled, and textured in multifilament yarns on fabric in different combinations is assessed in order to engineer a fabric of better ultraviolet protection factor (UPF. Methods. In order to engineer a fabric having optimum UV protection with sufficient comfort level in multifilament woven fabrics, four different yarn configurations, intermingled, textured, twisted, and flat, were used to develop twelve different fabric samples. The most UV absorbing and most demanding fibre polyethylene terephthalate (PET was considered in different filament configuration. Results. The combinations of intermingled warp with flat, intermingled, and textured weft provided excellent UVR protection comparatively at about 22.5 mg/cm2 fabric areal density. The presence of twisted yarn reduced the UV protection due to enhanced openness in fabric structure. Conclusion. The appropriate combination of warp and weft threads of different configuration should be selected judiciously in order to extract maximum UV protection and wear comfort attributes in multifilament woven PET fabrics.

  10. Intentionally fabricated autobiographical memories.

    Science.gov (United States)

    Justice, Lucy V; Morrison, Catriona M; Conway, Martin A

    2018-02-01

    Participants generated both autobiographical memories (AMs) that they believed to be true and intentionally fabricated autobiographical memories (IFAMs). Memories were constructed while a concurrent memory load (random 8-digit sequence) was held in mind or while there was no concurrent load. Amount and accuracy of recall of the concurrent memory load was reliably poorer following generation of IFAMs than following generation of AMs. There was no reliable effect of load on memory generation times; however, IFAMs always took longer to construct than AMs. Finally, replicating previous findings, fewer IFAMs had a field perspective than AMs, IFAMs were less vivid than AMs, and IFAMs contained more motion words (indicative of increased cognitive load). Taken together, these findings show a pattern of systematic differences that mark out IFAMs, and they also show that IFAMs can be identified indirectly by lowered performance on concurrent tasks that increase cognitive load.

  11. Fabrication of superhydrophobic cotton fabrics using crosslinking polymerization method

    Science.gov (United States)

    Jiang, Bin; Chen, Zhenxing; Sun, Yongli; Yang, Huawei; Zhang, Hongjie; Dou, Haozhen; Zhang, Luhong

    2018-05-01

    With the aim of removing and recycling oil and organic solvent from water, a facile and low-cost crosslinking polymerization method was first applied on surface modification of cotton fabrics for water/oil separation. Micro-nano hierarchical rough structure was constructed by triethylenetetramine (TETA) and trimesoyl chloride (TMC) that formed a polymeric layer on the surface of the fabric and anchored Al2O3 nanoparticles firmly between the fabric surface and the polymer layer. Superhydrophobic property was further obtained through self-assembly grafting of hydrophobic groups on the rough surface. The as-prepared cotton fabric exhibited superoleophilicity in atmosphere and superhydrophobicity both in atmosphere and under oil with the water contact angle of 153° and 152° respectively. Water/oil separation test showed that the as-prepared cotton fabric can handle with various oil-water mixtures with a high separation efficiency over 99%. More importantly, the separation efficiency remained above 98% over 20 cycles of reusing without losing its superhydrophobicity which demonstrated excellent reusability in oil/water separation process. Moreover, the as-prepared cotton fabric possessed good contamination resistance ability and self-cleaning property. Simulation washing process test showed the superhydrophobic cotton fabric maintained high value of water contact angle above 150° after 100 times washing, indicating great stability and durability. In summary, this work provides a brand-new way to surface modification of cotton fabric and makes it a promising candidate material for oil/water separation.

  12. Launching of Series Fabrication of the LHC Main Quadrupoles

    CERN Document Server

    Burgmer, R; Krischel, D; Peyrot, M; Rifflet, J M; Schmidt, P; Simon, F; Tortschanoff, Theodor

    2002-01-01

    A collaboration agreement between CERN and CEA-Saclay resulted in the successful development and construction of prototypes of the LHC main superconducting quadrupole magnets and their assembly into cold masses. A call for tender was issued in October 1999 and led to the adjudication of a contract to ACCEL Instruments. A number of components will be provided by CERN to be used either directly by ACCEL for integration into the cold mass units or by sub-suppliers before delivery to ACCEL. During the series fabrication CEA's engineers and technicians, already experienced from their prototype work, will ensure the technology transfer and the technical follow up in the factory. ACCEL had to adapt two large fabrication halls to the needs of the magnet fabrication and the cold mass assembly. Procedures for a tight quality assurance and the logistics for the timely supply of components and a high production rate are being established in close collaboration by the three parties concerned.

  13. Fabrication and experimentation of FRP helical spring

    Science.gov (United States)

    Ekanthappa, J.; Shiva Shankar, G. S.; Amith, B. M.; Gagan, M.

    2016-09-01

    In present scenario, the automobile industry sector is showing increased interest in reducing the unsprung weight of the automobile & hence increasing the fuel Efficiency. One of the feasible sub systems of a vehicle where weight reduction may be attempted is vehicle- suspension system. Usage of composite material is a proven way to lower the component weight without any compromise in strength. The composite materials are having high specific strength, more elastic strain energy storage capacity in comparison with those of steel. Therefore, helical coil spring made of steel is replaceable by composite cylindrical helical coil spring. This research aims at preparing a re-usable mandrel (mould) of Mild steel, developing a setup for fabrication, fabrication of FRP helical spring using continuous glass fibers and Epoxy Resin (Polymer). Experimentation has been conducted on fabricated FRP helical spring to determine its strength parameters & for failure analysis. It is found that spring stiffness (K) of Glass/Epoxy helical-spring is greater than steel-coil spring with reduced weight.

  14. Micromirror array for protein micro array fabrication

    Science.gov (United States)

    Lee, Kook-Nyung; Shin, Dong-Sik; Lee, Yoon-Sik; Kim, Yong-Kweon

    2003-05-01

    We have designed, fabricated and characterized a micromirror array for protein microarray fabrication that has a simple structure, and the straightforward fabrication process for the mirror will allow the use of low-cost mirrors in protein pattern applications. The characteristics of an exposure system utilizing the micromirror array have been demonstrated by means of an experiment employing a photoresist that is in general use in the semiconductor industry. The micromirror dimensions were 54 × 54 mum2, with a 30 mum separation between mirrors, and a 5.5 mum gap from the bottom electrode so that the mirror had an approximately 10° deflection angle. The size and separation of the mirror were designed in consideration of the protein pattern size and pitch, in contrast with the commercial Texas Instruments Digital Light Processor, which is utilized in the components of projection display systems. The exposure system combined with the micromirror has been used in the photochemical synthesis of chemical ligands via protein immobilization on a chip. Several photosynthesis experiments for peptide array synthesis have been carried out using the micromirror array. Parallel experiments on photochemical ligand synthesis on a chip can easily be performed in the laboratory using this exposure system.

  15. Wafer-scale micro-optics fabrication

    Science.gov (United States)

    Voelkel, Reinhard

    2012-07-01

    Micro-optics is an indispensable key enabling technology for many products and applications today. Probably the most prestigious examples are the diffractive light shaping elements used in high-end DUV lithography steppers. Highly-efficient refractive and diffractive micro-optical elements are used for precise beam and pupil shaping. Micro-optics had a major impact on the reduction of aberrations and diffraction effects in projection lithography, allowing a resolution enhancement from 250 nm to 45 nm within the past decade. Micro-optics also plays a decisive role in medical devices (endoscopes, ophthalmology), in all laser-based devices and fiber communication networks, bringing high-speed internet to our homes. Even our modern smart phones contain a variety of micro-optical elements. For example, LED flash light shaping elements, the secondary camera, ambient light and proximity sensors. Wherever light is involved, micro-optics offers the chance to further miniaturize a device, to improve its performance, or to reduce manufacturing and packaging costs. Wafer-scale micro-optics fabrication is based on technology established by the semiconductor industry. Thousands of components are fabricated in parallel on a wafer. This review paper recapitulates major steps and inventions in wafer-scale micro-optics technology. The state-of-the-art of fabrication, testing and packaging technology is summarized.

  16. Design and fabrication of NDA standards

    International Nuclear Information System (INIS)

    Long, S.M.; Hsue, S.T.

    1996-01-01

    The Plutonium Facility, TA-55, at Los Alamos National Laboratory is currently producing NDA calibration standards used by various laboratories in the DOE complex. These NIST traceable standards have been produced to calibrate NDA instruments for accountability measurements used for resolving shipper/receiver differences, and for accountability in process residues and process waste. Standards are needed to calibrate various NDA (Non-destructive Assay) instruments such as neutron coincidence counters, gamma-ray counters, and calorimeters. These instruments measure various ranges of nuclear material being produced in the DOE nuclear community. Los Alamos National Laboratory has taken a lead role in fabrication of uranium and plutonium standards, along with other actinides such as neptunium and americium. These standards have been fabricated for several laboratories within the complex. This paper will summarize previous publications detailing the careful planning encompassing components such as precise weighing, destructive analysis, and the use of post fabrication NDA measurements to confirm that the standards meet all preliminary expectations before use in instrument calibration. The paper will also describe the specialized containers, diluents, and the various amount of nuclear materials needed to accommodate the calibration ranges of the instruments

  17. Two component micro injection moulding for moulded interconnect devices

    DEFF Research Database (Denmark)

    Islam, Aminul

    2008-01-01

    is to explore and overcome the challenges associated with MID production by two component injection moulding. Fabrication of micro scale MIDs by two component injection moulding, calls for plastic materials suitable for two component micro injection moulding and requires optimization in injection moulding...... component injection moulding is one of the most industrially adaptive processes. However, the use of two component injection moulding for MID fabrication, with circuit patterns in the sub-millimeter range, is still a big challenge at the present state of technology. The scope of the current Ph.D. project...... and selective metallization. Integrated knowledge about the materials, tooling, process conditions and product development is needed. The main issues to be taken into account for two component injection moulded MIDs are: • Two component injection moulding with a sharp interface between the two polymers...

  18. Unidirectional Fabric Drape Testing Method.

    Science.gov (United States)

    Mei, Zaihuan; Shen, Wei; Wang, Yan; Yang, Jingzhi; Zhou, Ting; Zhou, Hua

    2015-01-01

    In most cases, fabrics such as curtains, skirts, suit pants and so on are draped under their own gravity parallel to fabric plane while the gravity is perpendicular to fabric plane in traditional drape testing method. As a result, it does not conform to actual situation and the test data is not convincing enough. To overcome this problem, this paper presents a novel method which simulates the real mechanical conditions and ensures the gravity is parallel to the fabric plane. This method applied a low-cost Kinect Sensor device to capture the 3-dimensional (3D) drape profile, thus we obtained the drape degree parameters and aesthetic parameters by 3D reconstruction and image processing and analysis techniques. The experiment was conducted on our self-devised drape-testing instrument by choosing different kinds of weave structure fabrics as our testing samples and the results were compared with those of traditional method and subjective evaluation. Through regression and correlation analysis we found that this novel testing method was significantly correlated with the traditional and subjective evaluation method. We achieved a new, non-contact 3D measurement method for drape testing, namely unidirectional fabric drape testing method. This method is more suitable for evaluating drape behavior because it is more in line with actual mechanical conditions of draped fabrics and has a well consistency with the requirements of visual and aesthetic style of fabrics.

  19. Fabrication and characterization of a slanting-type solar water ...

    African Journals Online (AJOL)

    The system includes four major components; a wooden basin of surface area 0.16 m2, an absorber surface, a slanting glass roof and a condensate channel. Very cheap locally available materials were used to fabricate the solar still. The solar still produced an average of 0.09 m3 of distilled water per day, and this study was ...

  20. Evaluation of Fine Denier and Microdenier Multifilament Fabrics

    National Research Council Canada - National Science Library

    Winterhalter, C

    2002-01-01

    ... to MIL-C-3924, Cloth, Oxford, Cotton Warp and Nylon Filling, Quarpel Treated. MIL-C-3924 is one of the military's lightest weight water repellent fabrics and is used in the Snow Camouflage Overwhites and various hood components and caps...

  1. Project Plan Remote Target Fabrication Refurbishment Project

    International Nuclear Information System (INIS)

    Bell, Gary L.; Taylor, Robin D.

    2009-01-01

    In early FY2009, the DOE Office of Science - Nuclear Physics Program reinstated a program for continued production of 252 Cf and other transcurium isotopes at the Radiochemical Engineering Development Center (REDC) at Oak Ridge National Laboratory (ORNL). The FY2009 major elements of the workscope are as follows: (1) Recovery and processing of seven transuranium element targets undergoing irradiation at the High Flux Isotope Reactor (HFIR) at ORNL; (2) Development of a plan to manufacture new targets for irradiation beginning in early- to mid-FY10 to supply irradiated targets for processing Campaign 75 (TRU75); and (3) Refurbishment of the target manufacturing equipment to allow new target manufacture in early FY10 The 252 Cf product from processing Campaign 74 (recently processed and currently shipping to customers) is expected to supply the domestic demands for a period of approximately two years. Therefore it is essential that new targets be introduced for irradiation by the second quarter of FY10 (HFIR cycle 427) to maintain supply of 252 Cf; the average irradiation period is ∼10 HFIR cycles, requiring about 1.5 calendar years. The strategy for continued production of 252 Cf depends upon repairing and refurbishing the existing pellet and target fabrication equipment for one additional target production campaign. This equipment dates from the mid-1960s to the late 1980s, and during the last target fabrication campaign in 2005- 2006, a number of component failures and operations difficulties were encountered. It is expected that following the target fabrication and acceptance testing of the targets that will supply material for processing Campaign 75 a comprehensive upgrade and replacement of the remote hot-cell equipment will be required prior to subsequent campaigns. Such a major refit could start in early FY 2011 and would take about 2 years to complete. Scope and cost estimates for the repairs described herein were developed, and authorization for the work

  2. DRAPING SIMULATION OF WOVEN FABRICS

    Energy Technology Data Exchange (ETDEWEB)

    Rodgers, William [General Motors LLC; Jin, Xiaoshi [ESI Group NA; Zhu, Jiang [Optimal CAE; Wathen, Terrence [General Motors LLC; Doroudian2, Mark [ESI Group NA; Aitharaju, Venkat [General Motors LLC

    2016-09-07

    Woven fabric composites are extensively used in molding complex geometrical shapes due to their high conformability compared to other fabrics. Preforming is an important step in the overall process, where the two-dimensional fabric is draped to become the three-dimensional shape of the part prior to resin injection. During preforming, the orientation of the yarns may change significantly compared to the initial orientations. Accurate prediction of the yarn orientations after molding is important for evaluating the structural performance of the final part. This paper presents a systematic investigation of the angle changes during the preform operation for carbon fiber twill and satin weave fabrics. Preforming experiments were conducted using a truncated pyramid mold geometry designed and fabricated at the General Motors Research Laboratories. Predicted results for the yarn orientations were compared with experimental results and good agreement was observed

  3. Fabricating multifunctional silver nanoparticles-coated cotton fabric

    Directory of Open Access Journals (Sweden)

    Mohammad Shateri-Khalilabad

    2017-05-01

    Full Text Available Silver nanoparticles with high density coating were formed on the surface of cotton fabric through pre-activation by potassium hydroxide and in situ reduction of silver nitrate. The silver nanoparticles-coated fabric was then reacted with hexadecyltrimethoxysilane, which resulted in the formation of low surface energy layer around the fabric. The fabrics were characterized by reflectance spectrophotometry, scanning electron microscopy, energy dispersive X-ray spectroscopy and X-ray diffraction patterns. Wettability properties were measured by contact angle goniometry and shedding angle technique. Antibacterial activity was determined against Gram-positive Staphylococcus aureus and Gram-negative Escherichia coli. Ultraviolet-blocking was measured via transmittance data in the range of 280–400 nm. Microscopy images showed the formation of uniform and high density coating of silver on the surface of cotton fibers. The fabric showed hydrophobicity with CA of 158 ± 4.3° and SHA of 7°. Also, it demonstrated a high antibacterial activity against two bacterial challenges, as shown via formation of inhibition zone. Excellent ultraviolet protection of the fabric was demonstrated by ultraviolet protection factor value of 296. The fabric also showed good durability against repeated laundering.

  4. Two component micro injection moulding for moulded interconnect devices

    DEFF Research Database (Denmark)

    Among the available MID process chains, two component (2k) injection moulding with subsequent selective metallization is one of the most industrially adaptive processes. However the use of two component injection moulding for MID fabrication, with circuit patterns in the sub-millimeter range, is ......, is a challenge for industrial MID production. This research work demonstrates the feasibilities and challenges of MID fabrication by 2k moulding for highly precise and technically challenging applications......Among the available MID process chains, two component (2k) injection moulding with subsequent selective metallization is one of the most industrially adaptive processes. However the use of two component injection moulding for MID fabrication, with circuit patterns in the sub-millimeter range...

  5. Fabrication of complex structures or assemblies by Hot Isostatic Pressure (HIP) welding

    Science.gov (United States)

    Ashurst, A. N.; Goldstein, M.; Ryan, M. J.; Lessmann, G. G.; Bryant, W. A.

    1974-01-01

    HIP welding is effective method for fabricating complex structures or assemblies such as alternator rotors, regeneratively-cooled rocket-motor thrust chambers, and jet engine turbine blades. It can be applied to fabrication of many assemblies which require that component parts be welded together along complex interfaces.

  6. Superconducting circuit fabrication

    International Nuclear Information System (INIS)

    Stein, B.F.; Young, P.L.

    1984-01-01

    An improved method of anodization of thin films for the fabrication of superconducting devices. An electrically conducting contact layer is formed over a substrate between an electrically conducting object layer and the substrate. Also, an electrically insulating layer is formed between the object layer and the contact layer. The contact layer is connected to a power supply and at least a preselected portion of the object layer is anodized to a predetermined thickness. This may include anodizing all of some preselected portions through the complete thickness of the object layer. A pattern of hardened photoresist on the object layer provides portions not protected by the pattern. When anodization of the electrically conducting object layer takes place, the resulting anodized portion is thicker than the thickness of the portion of the object layer that it replaces. The present invention further includes reducing the preselected portion of the object layer to be anodized by a predetermined amount before anodizing so that when anodization is complete, the resulting partially anodized partially conducting object layer is substantially planar. Alternatively, the thickness of the anodized preselected portions can be reduced after anodizing by a predetermined amount to cause the layer to be substantially planar. The same pattern of hardened photoresist can be used when reducing the thickness of portions of the object layer or anodized preselected portions

  7. Switching Fabric Based on Multi-Level LVDS Compatible Interconnect, Phase II

    Data.gov (United States)

    National Aeronautics and Space Administration — Switching fabric (SF) is the key component of the next generation of back plane interconnects. Low power, TID and SEU resistant and high bandwidth upgradeable...

  8. Monitoring Electron Beam Freeform Fabrication by Active Machine Vision, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — Additive manufacturing is a modern fabrication process by which three dimensional components are built up layer-by-layer. Each layer corresponds to a cross-section...

  9. Switching Fabric based on Multi-Level LVDS Compatible Interconnect, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — The switching fabric (SF) is a key component of the next generation back plane interconnects. Extremely low-power, radiation-hardened, high-bandwidth upgradeable...

  10. MOX fuel fabrication at AECL

    International Nuclear Information System (INIS)

    Dimayuga, F.C.; Jeffs, A.T.

    1995-01-01

    Atomic Energy of Canada Limited's mixed-oxide (MOX) fuel fabrication activities are conducted in the Recycle Fuel Fabrication Laboratories (RFFL) at the Chalk River Laboratories. The RFFL facility is designed to produce experimental quantities of CANDU MOX fuel for reactor physics tests or demonstration irradiations. From 1979 to 1987, several MOX fuel fabrication campaigns were run in the RFFL, producing various quantities of fuel with different compositions. About 150 bundles, containing over three tonnes of MOX, were fabricated in the RFFL before operations in the facility were suspended. In late 1987, the RFFL was placed in a state of active standby, a condition where no fuel fabrication activities are conducted, but the monitoring and ventilation systems in the facility are maintained. Currently, a project to rehabilitate the RFFL and resume MOX fuel fabrication is nearing completion. This project is funded by the CANDU Owners' Group (COG). The initial fabrication campaign will consist of the production of thirty-eight 37-element (U,Pu)O 2 bundles containing 0.2 wt% Pu in Heavy Element (H.E.) destined for physics tests in the zero-power ZED-2 reactor. An overview of the Rehabilitation Project will be given. (author)

  11. Fabric circuits and method of manufacturing fabric circuits

    Science.gov (United States)

    Chu, Andrew W. (Inventor); Dobbins, Justin A. (Inventor); Scully, Robert C. (Inventor); Trevino, Robert C. (Inventor); Lin, Greg Y. (Inventor); Fink, Patrick W. (Inventor)

    2011-01-01

    A flexible, fabric-based circuit comprises a non-conductive flexible layer of fabric and a conductive flexible layer of fabric adjacent thereto. A non-conductive thread, an adhesive, and/or other means may be used for attaching the conductive layer to the non-conductive layer. In some embodiments, the layers are attached by a computer-driven embroidery machine at pre-determined portions or locations in accordance with a pre-determined attachment layout before automated cutting. In some other embodiments, an automated milling machine or a computer-driven laser using a pre-designed circuit trace as a template cuts the conductive layer so as to separate an undesired portion of the conductive layer from a desired portion of the conductive layer. Additional layers of conductive fabric may be attached in some embodiments to form a multi-layer construct.

  12. Fabrication of cotton fabric with superhydrophobicity and flame retardancy.

    Science.gov (United States)

    Zhang, Ming; Wang, Chengyu

    2013-07-25

    A simple and facile method for fabricating the cotton fabric with superhydrophobicity and flame retardancy is described in the present work. The cotton fabric with the maximal WCA of 160° has been prepared by the covalent deposition of amino-silica nanospheres and the further graft with (heptadecafluoro-1,1,2,2-tetradecyl) trimethoxysilane. The geometric microstructure of silica spheres was measured by transmission electron microscopy (TEM). The cotton textiles before and after treatment were characterized by using scanning electron microscope (SEM) and X-ray photoelectron spectroscopy (XPS). The wetting behavior of cotton samples was investigated by water contact angle measurement. Moreover, diverse performances of superhydrophobic cotton textiles have been evaluated as well. The results exhibited the outstanding superhydrophobicity, excellent waterproofing durability and flame retardancy of the cotton fabric after treatment, offering a good opportunity to accelerate the large-scale production of superhydrophobic textiles materials for new industrial applications. Copyright © 2013 Elsevier Ltd. All rights reserved.

  13. Fabrication of integrated metallic MEMS devices

    DEFF Research Database (Denmark)

    Yalcinkaya, Arda Deniz; Ravnkilde, Jan Tue; Hansen, Ole

    2002-01-01

    A simple and complementary metal oxide semiconductor (CMOS) compatible fabrication technique for microelectromechanical (MEMS) devices is presented. The fabrication technology makes use of electroplated metal layers. Among the fabricated devices, high quality factor microresonators...

  14. Fabrication of nanowires and nanostructures

    DEFF Research Database (Denmark)

    Mátéfi-Tempfli, Stefan; Mátéfi-Tempfli, M.; Piraux, L.

    2009-01-01

    We report on different approaches that we have adopted and developed for the fabrication of nanowires and nanostructures. Methods based on template synthesis and on self organization seem to be the most promising for the fabrication of nanomaterials and nanostructures due to their easiness and low...... cost. The development of a supported nanoporous alumina template and the possibility of using this template to combine electrochemical synthesis with lithographic methods open new ways for the fabrication of complex nanostructures. The numerous advantages of the supported template and its compatibility...

  15. Automated fabrication of reactor fuel

    International Nuclear Information System (INIS)

    Nyman, D.H.; McLemore, D.R.; Bennett, D.W.; Yatabe, J.M.

    1980-01-01

    The development of Secure Automated Fabrication (SAF) methods is the goal of the United States breeder reactor program and will form the technological basis for the future breeder reactor fuel supply. A major factor in achieving this goal is the development of remotely operated fuel fabrication equipment. The unit operations are being designed for microprocessor control connected to a central control center. The program schedule is to demonstrate the feasibility of automated pellet fuel fabrication and remote maintenance techniques by the mid-1980's. Development of major ceramic unit operations and the required computer control system is currently in the engineering testing stage

  16. Automated fabrication of thoria based fuel: challenges and initiatives

    International Nuclear Information System (INIS)

    Jayarajan, K.

    2015-01-01

    The processes and techniques for fabrication of uranium-based fuel and plutonium-based fuel are well established. However, fabrication of thorium-based fuel has an additional challenge, due to high gamma radiation. 233 U produced from thorium in reactor is contaminated with 232 U, whose daughter products are hard gamma emitters. Therefore, 233 U fuel can be fabricated only in shielded cells. We have limited experience of remote fuel fabrication in shielded facility. Therefore, a mock up facility is being set-up at BARC to demonstrate fully remotised and fully automated fuel fabrication. In the facility, the automated handling of mixed oxide powder, fuel pellets, fuel pins and fuel cluster will be demonstrated. In addition to various processing, these components are subjected to a many inspections, such as dimension inspection, weight measurement, visual inspection and various NDTs. Mock-up systems for automated fabrication of pellets and pins are already made. Many novel tools and techniques were developed for automated material transfer. Another outcome of the development is the layout of hot cell and equipments, optimising the hot cell space, the number of material transfers and the number of equipments. The layout also provides access for remote maintenance

  17. Assesment On The Possibility To Modify Fabrication Equipment For Fabrication Of HWR And LWR Fuel Elements

    International Nuclear Information System (INIS)

    Tri-Yulianto

    1996-01-01

    Based on TOR BATAN for PELITA VI. On of BATAN program in the fuel element production technology section is the acquisition of the fuel element fabrication technology for research reactor as well as power reactor. The acquisition can be achieved using different strategies, e.g. by utilizing the facility owned for research and development of the technology desired or by transferring the technology directly from the source. With regards to the above, PEBN through its facility in BEBE has started the acquisition of the fuel element fabrication technology for power reactor by developing the existing equipment initially designed to fabricate HWR Cinere fuel element. The development, by way of modifying the equipment, is intended for the production of HWR (Candu) and LWR (PWR and BWR) fuel elements. To achieve above objective, at the early stage of activity, an assesment on the fabrication equipment for pelletizing, component production and assembly. The assesment was made by comparing the shape and the size of the existing fuel element with those used in the operating reactors such as Candu reactors, PWR and BWR. Equipment having the potential to be modified for the production of HWR fuel elements are as followed: For the pelletizing equipment, the punch and dies can be used of the pressing machine for making green pellet can be modified so that different sizes of punch and dies can be used, depending upon the size of the HWR and LWR pellets. The equipment for component production has good potential for modification to produce the HWR Candu fuel element, which has similar shape and size with those of the existing fuel element, while the possibility of producing the LWR fuel element component is small because only a limited number of the required component can be made with the existing equipment. The assembly equipment has similar situation whit that of the component production, that is, to assemble the HWR fuel element modification of few assembly units very probable

  18. Fabrication of integrated metallic MEMS devices

    DEFF Research Database (Denmark)

    Yalcinkaya, Arda Deniz; Ravnkilde, Jan Tue; Hansen, Ole

    2002-01-01

    A simple and complementary metal oxide semiconductor (CMOS) compatible fabrication technique for microelectromechanical (MEMS) devices is presented. The fabrication technology makes use of electroplated metal layers. Among the fabricated devices, high quality factor microresonators are characteri......A simple and complementary metal oxide semiconductor (CMOS) compatible fabrication technique for microelectromechanical (MEMS) devices is presented. The fabrication technology makes use of electroplated metal layers. Among the fabricated devices, high quality factor microresonators...

  19. Thin-Walled Double Side Freeform Component Milling Process with Paraffin Filling Method

    Directory of Open Access Journals (Sweden)

    Jun Zha

    2017-11-01

    Full Text Available The machining of thin-walled double side freeform component has many challenges in terms of the geometrical complexity, high-requirement accuracy, and especially low stiffness. This paper surveys the filling method during the milling processes of thin-walled double side freeform component. Firstly, the DEFORM-3D was used to analyze and calculate the surface residual stress which provides a theoretical basis for parameters selection of the rough milling process, and the optimal milling parameters were obtained by the Taguchi method. Residual stress measurements have been carried out to verify the simulation results. The results show the difference between simulation and experimental data is less than 15%. Secondly, semi-finishing parameters and finishing process parameters were determined by equal error step length and step distance method. Thirdly, two machining experiments were conducted with and without paraffin filling, and the accuracy was measured by coordinate measurement machine. The results shown that the PV values are 25.16 μm and 20.34 μm for the concave and convex surface, and the corresponding RMS values are 13.75 μm and 11.93 μm in the first milling experiment. The PV values have improved to 8.53 μm and 7.12 μm, and RMS values have improved to 2.45 μm and 3.05 μm by the filled method applied.

  20. Integrating 3D CAD data for manufacturing and fabrication the core model of reactor TRIGA PUSPATI

    International Nuclear Information System (INIS)

    Abu Bakar Harun

    2005-01-01

    This paper describe the intrigue integration of digital 3 Dimensional Computer Aided Design (3D CAD) data manipulation for the Core Model fabrication of REAKTOR TRIGA PUSPATI and ready for mass manufacturing. 3 Dimensional CAD data from Computer Aided Design program will be used as an interpreter in the fabrication of this project. The Core Model of REAKTOR TRIGA PUSPATI will be fabricated with the aid of 3D CAD drawings and digital files. The components will be segregated and divided into 2 categories namely Conventional d Rapid Fabrication. (Author)

  1. Pilling Resistance of Knitted Fabrics

    Directory of Open Access Journals (Sweden)

    Gita BUSILIENĖ

    2011-09-01

    Full Text Available Knitted fabrics with different quantity of elastane, conspicuous by high viscosity and elasticity, having one of the most important performance properties - resistance to pilling are often used in the production of high quality sportswear. During technological process imitating operating conditions, the behaviour of knitted fabrics may be changed by different industrial softeners from 12 % to 20 % of active substance, for example fatty acid condensate (Tubingal 5051 or silicone micro emulsion (Tubingal SMF. The aim of this investigation is to define the influence of fibrous composition and chemical softeners to the propensity of fuzzing and pilling of plain and plated jersey pattern knitted fabrics. The results of investigations showed that fibrous composition and thickness of materials (up to 6 % and washing as well as softening (from 33 % to 67 % change the resistance of knitted fabrics to pilling.http://dx.doi.org/10.5755/j01.ms.17.3.597

  2. Geoacoustic Physical Model Fabrication Laboratory

    Data.gov (United States)

    Federal Laboratory Consortium — FUNCTION: Fabricates three-dimensional rough surfaces (e.g., fractals, ripples) out of materials such as PVC or wax to simulate the roughness properties associated...

  3. Net-Shape Tailored Fabrics For Complex Composite Structures

    Science.gov (United States)

    Farley, Gary L.

    1995-01-01

    Proposed novel looms used to make fabric preforms for complex structural elements, both stiffening elements and skin, from continuous fiber-reinforced composite material. Components of looms include custom reed and differential fabric takeup system. Structural parts made best explained by reference to curved "I" cross-section frame. Technology not limited to these fiber orientations or geometry; fiber angles, frame radius of curvature, frame height, and flange width changed along length of structure. Weaving technology equally applicable to structural skins, such as wing of fuselage skins.

  4. Biofabrication micro- and nano-fabrication, printing, patterning and assemblies

    CERN Document Server

    Forgacs, Gabor

    2013-01-01

    Biofabrication is a practical guide to the novel, inherently cross-disciplinary scientific field that focuses on biomanufacturing processes and a related range of emerging technologies. These processes and technologies ultimately further the development of products that may involve living (cells and/or tissues) and nonliving (bio-supportive proteins, scaffolds) components. The book introduces readers to cell printing, patterning, assembling, 3D scaffold fabrication, cell/tissue-on-chips as a coherent micro-/nano-fabrication toolkit. Real-world examples illustrate how to apply biofabric

  5. Additive Manufacturing of Molds for Fabrication of Insulated Concrete Block

    Energy Technology Data Exchange (ETDEWEB)

    Love, Lonnie J. [ORNL; Lloyd, Peter D. [ORNL

    2018-02-01

    ORNL worked with concrete block manufacturer, NRG Insulated Block, to demonstrate additive manufacturing of a multi-component block mold for its line of insulated blocks. Solid models of the mold parts were constructed from existing two-dimensional drawings and the parts were fabricated on a Stratasys Fortus 900 using ULTEM 9085. Block mold parts were delivered to NRG and installed on one of their fabrication lines. While form and fit were acceptable, the molds failed to function during NRG’s testing.

  6. Design and Testing of Improved Spacesuit Shielding Components

    International Nuclear Information System (INIS)

    Ware, J.; Ferl, J.; Wilson, J.W.; Clowdsley, M.S.; DeAngelis, G.; Tweed, J.; Zeitlin, C.J.

    2002-01-01

    In prior studies of the current Shuttle Spacesuit (SSA), where basic fabric lay-ups were tested for shielding capabilities, it was found that the fabric portions of the suit give far less protection than previously estimated due to porosity and non-uniformity of fabric and LCVG components. In addition, overall material transmission properties were less than optimum. A number of alternate approaches are being tested to provide more uniform coverage and to use more efficient materials. We will discuss in this paper, recent testing of new material lay-ups/configurations for possible use in future spacesuit designs

  7. Design and Testing of Improved Spacesuit Shielding Components

    Energy Technology Data Exchange (ETDEWEB)

    Ware, J.; Ferl, J.; Wilson, J.W.; Clowdsley, M.S.; DeAngelis, G.; Tweed, J.; Zeitlin, C.J.

    2002-05-08

    In prior studies of the current Shuttle Spacesuit (SSA), where basic fabric lay-ups were tested for shielding capabilities, it was found that the fabric portions of the suit give far less protection than previously estimated due to porosity and non-uniformity of fabric and LCVG components. In addition, overall material transmission properties were less than optimum. A number of alternate approaches are being tested to provide more uniform coverage and to use more efficient materials. We will discuss in this paper, recent testing of new material lay-ups/configurations for possible use in future spacesuit designs.

  8. Silicone nanocomposite coatings for fabrics

    Science.gov (United States)

    Eberts, Kenneth (Inventor); Lee, Stein S. (Inventor); Singhal, Amit (Inventor); Ou, Runqing (Inventor)

    2011-01-01

    A silicone based coating for fabrics utilizing dual nanocomposite fillers providing enhanced mechanical and thermal properties to the silicone base. The first filler includes nanoclusters of polydimethylsiloxane (PDMS) and a metal oxide and a second filler of exfoliated clay nanoparticles. The coating is particularly suitable for inflatable fabrics used in several space, military, and consumer applications, including airbags, parachutes, rafts, boat sails, and inflatable shelters.

  9. Mitigating component performance variation

    Science.gov (United States)

    Gara, Alan G.; Sylvester, Steve S.; Eastep, Jonathan M.; Nagappan, Ramkumar; Cantalupo, Christopher M.

    2018-01-09

    Apparatus and methods may provide for characterizing a plurality of similar components of a distributed computing system based on a maximum safe operation level associated with each component and storing characterization data in a database and allocating non-uniform power to each similar component based at least in part on the characterization data in the database to substantially equalize performance of the components.

  10. Variability and component composition

    NARCIS (Netherlands)

    T. van der Storm (Tijs)

    2004-01-01

    textabstractIn component-based product populations, feature models have to be described at the component level to be able to benefit from a product family approach. As a consequence, composition of components becomes very complex. We describe how component-level variability can be managed in the

  11. IPRDS: component histories and nuclear plant aging

    International Nuclear Information System (INIS)

    Borkowski, R.J.; Kahl, W.K.

    1984-01-01

    A comprehensive assessment of nuclear power plant component operating histories, maintenance histories, and design and fabrication details is essential to understanding aging phenomena. As part of the In-Plant Reliability Data System (IPRDS), an attempt is being made to collect and analyze such information from a sampling of US nuclear power plants. Utilizing the IPRDS, one can reconstruct the failure history of the components and gain new insight into the causes and modes of failures resulting from normal or premature aging. This information assembled from the IPRDS can be combined with operating histories and postservice component inspection results for cradle-to-grave assessments of component aging under operating conditions. A comprehensive aging assessment can then be used to provide guidelines for improving the detection, monitoring, and mitigation of aging-related failures

  12. Analysis of fabric materials cut using ultraviolet laser ablation

    Science.gov (United States)

    Tsai, Hsin-Yi; Yang, Chih-Chung; Hsiao, Wen-Tse; Huang, Kuo-Cheng; Andrew Yeh, J.

    2016-04-01

    Laser ablation technology has widely been applied in the clothing industry in recent years. However, the laser mechanism would affect the quality of fabric contours and its components. Hence, this study examined carbonization and oxidation conditions and contour variation in nonwoven, cotton, and composite leather fabrics cut by using an ultraviolet laser at a wavelength of 355 nm. Processing parameters such as laser power, pulse frequency, scanning speed, and number of pulses per spot were adjusted to investigate component variation of the materials and to determine suitable cutting parameters for the fabrics. The experimental results showed that the weights of the component changed substantially by pulse frequency but slightly by laser power, so pulse frequency of 100 kHz and laser power of 14 W were the approximate parameters for three fabrics for the smaller carbonization and a sufficient energy for rapidly cutting, which the pulse duration of laser system was fixed at 300 μs and laser irradiance was 0.98 J/mm2 simultaneously. In addition, the etiolate phenomenon of nonwoven was reduced, and the component weight of cotton and composite leather was closed to the value of knife-cut fabric as the scanning speed increased. The approximate scanning speed for nonwoven and composite leather was 200 mm/s, and one for cotton was 150 mm/s, respectively. The sharper and firmer edge is obtained by laser ablation mechanism in comparison with traditional knife cutting. Experimental results can serve as the reference for laser cutting in the clothing industry, for rapidly providing smoother patterns with lower carbonization and oxidation edge in the fashion industry.

  13. Durable Superomniphobic Surface on Cotton Fabrics via Coating of Silicone Rubber and Fluoropolymers

    Directory of Open Access Journals (Sweden)

    Arsheen Moiz

    2018-03-01

    Full Text Available Performance textiles that protect human from different threats and dangers from environment are in high demand, and the advancement in functionalization technology together with employing advanced materials have made this an area of research focus. In this work, silicone rubber and environmentally friendly fluoropolymers have been employed to explore superomniphobic surface on cotton fabrics without compromising comfort much. It has been found that a cross-linked network between the rubber membrane and the fluoropolymers has been formed. The surface appearance, morphology, handle, thickness and chemical components of the surface of cotton fabrics have been changed. The coated fabrics showed resistance to water, aqueous liquid, oil, chemicals and soil. The comfort of the coated fabrics is different to uncoated cotton fabrics due to the existence of coated layers on the surface of cotton fabrics. This work would benefit the development and design of the next generation of performance textiles with balanced performance and comfort.

  14. Miniature Scroll Pumps Fabricated by LIGA

    Science.gov (United States)

    Wiberg, Dean; Shcheglov, Kirill; White, Victor; Bae, Sam

    2009-01-01

    Miniature scroll pumps have been proposed as roughing pumps (low - vacuum pumps) for miniature scientific instruments (e.g., portable mass spectrometers and gas analyzers) that depend on vacuum. The larger scroll pumps used as roughing pumps in some older vacuum systems are fabricated by conventional machining. Typically, such an older scroll pump includes (1) an electric motor with an eccentric shaft to generate orbital motion of a scroll and (2) conventional bearings to restrict the orbital motion to a circle. The proposed miniature scroll pumps would differ from the prior, larger ones in both design and fabrication. A miniature scroll pump would include two scrolls: one mounted on a stationary baseplate and one on a flexure stage (see figure). An electromagnetic actuator in the form of two pairs of voice coils in a push-pull configuration would make the flexure stage move in the desired circular orbit. The capacitance between the scrolls would be monitored to provide position (gap) feedback to a control system that would adjust the drive signals applied to the voice coils to maintain the circular orbit as needed for precise sealing of the scrolls. To minimize power consumption and maximize precision of control, the flexure stage would be driven at the frequency of its mechanical resonance. The miniaturization of these pumps would entail both operational and manufacturing tolerances of pump components. In addition, the vibrations of conventional motors and ball bearings exceed these tight tolerances by an order of magnitude. Therefore, the proposed pumps would be fabricated by the microfabrication method known by the German acronym LIGA ( lithographie, galvanoformung, abformung, which means lithography, electroforming, molding) because LIGA has been shown to be capable of providing the required tolerances at large aspect ratios.

  15. Fabrication of Composite Combustion Chamber/Nozzle for Fastrac Engine

    Science.gov (United States)

    Lawrence, T.; Beshears, R.; Burlingame, S.; Peters, W.; Prince, M.; Suits, M.; Tillery, S.; Burns, L.; Kovach, M.; Roberts, K.

    2001-01-01

    The Fastrac Engine developed by the Marshall Space Flight Center for the X-34 vehicle began as a low cost engine development program for a small booster system. One of the key components to reducing the engine cost was the development of an inexpensive combustion chamber/nozzle. Fabrication of a regeneratively cooled thrust chamber and nozzle was considered too expensive and time consuming. In looking for an alternate design concept, the Space Shuttle's Reusable Solid Rocket Motor Project provided an extensive background with ablative composite materials in a combustion environment. An integral combustion chamber/nozzle was designed and fabricated with a silica/phenolic ablative liner and a carbon/epoxy structural overwrap. This paper describes the fabrication process and developmental hurdles overcome for the Fastrac engine one-piece composite combustion chamber/nozzle.

  16. Fabrication of high aspect ratio micro electrode by using EDM

    International Nuclear Information System (INIS)

    Elsiti, Nagwa Mejid; Noordin, M.Y.; Alkali, Adam Umar

    2016-01-01

    The electrical discharge machining (EDM) process inherits characteristics that make it a promising micro-machining technique. Micro electrical discharge machining (micro- EDM) is a derived form of EDM, which is commonly used to manufacture micro and miniature parts and components by using the conventional electrical discharge machining fundamentals. Moving block electro discharge grinding (Moving BEDG) is one of the processes that can be used to fabricate micro-electrode. In this study, a conventional die sinker EDM machine was used to fabricate the micro-electrode. Modifications are made to the moving BEDG, which include changing the direction of movements and control gap in one electrode. Consequently current was controlled due to the use of roughing, semi-finishing and finishing parameters. Finally, a high aspect ratio micro-electrode with a diameter of 110.49μm and length of 6000μm was fabricated. (paper)

  17. A facile method to fabricate superhydrophobic cotton fabrics

    Science.gov (United States)

    Zhang, Ming; Wang, Shuliang; Wang, Chengyu; Li, Jian

    2012-11-01

    A facile and novel method for fabricating superhydrophobic cotton fabrics is described in the present work. The superhydrophobic surface has been prepared by utilizing cationic poly (dimethyldiallylammonium chloride) and silica particles together with subsequent modification of (heptadecafluoro-1,1,2,2-tetradecyl) trimethoxysilane. The size distribution of silica particles was measured by Particle Size Analyzer. The cotton textiles before and after treatment were characterized by using scanning electron microscope (SEM) and X-ray photoelectron spectroscopy (XPS). The wetting behavior of cotton samples was investigated by water contact angle measurement. Moreover, the superhydrophobic durability of coated cotton textiles has been evaluated by exposure, immersion and washing tests. The results show that the treated cotton fabrics exhibited excellent chemical stability and outstanding non-wettability with the WCA of 155 ± 2°, which offers an opportunity to accelerate the large-scale production of superhydrophobic textiles materials for new industrial applications.

  18. Fabrication of Nanoimprint stamps for photonic crystals

    International Nuclear Information System (INIS)

    Kouba, J; Kubenz, M; Mai, A; Ropers, G; Eberhardt, W; Loechel, B

    2006-01-01

    We report on fabrication of nanoimprint stamps for fabrication of two dimensional photonic crystals in visible range of spectra. Nanoimprint stamps made of silicon and/or nickel were successfully fabricated using electron beam lithography and advanced dry etching techniques. The quality of the stamps was evaluated using scanning electron microscopy. The fabricated stamps were also evaluated by imprinting them into suitable polymer materials

  19. Metallic Reactor Fuel Fabrication for SFR

    Energy Technology Data Exchange (ETDEWEB)

    Song, Hoon; Kim, Jong-Hwan; Ko, Young-Mo; Woo, Yoon-Myung; Kim, Ki-Hwan; Lee, Chan-Bock [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2015-05-15

    The metal fuel for an SFR has such advantages such as simple fabrication procedures, good neutron economy, high thermal conductivity, excellent compatibility with a Na coolant, and inherent passive safety 1. U-Zr metal fuel for SFR is now being developed by KAERI as a national R and D program of Korea. The fabrication technology of metal fuel for SFR has been under development in Korea as a national nuclear R and D program since 2007. The fabrication process for SFR fuel is composed of (1) fuel slug casting, (2) loading and fabrication of the fuel rods, and (3) fabrication of the final fuel assemblies. Fuel slug casting is the dominant source of fuel losses and recycled streams in this fabrication process. Fabrication on the rod type metallic fuel was carried out for the purpose of establishing a practical fabrication method. Rod-type fuel slugs were fabricated by injection casting. Metallic fuel slugs fabricated showed a general appearance was smooth.

  20. Optical Microresonators Theory, Fabrication, and Applications

    CERN Document Server

    Heebner, John; Ibrahim, Tarek

    2008-01-01

    This book explains why microresonators came to be important components in the photonic toolbox. While functionally similar to the Fabry-Perot, microring resonators offer a planar nature which is naturally compatible with monolithic microfabrication technologies. In these chapters lie the principles required to characterize, design, construct, and implement microresonators as lasers, amplifiers, sensors, filters, demultiplexers, switches, routers, and logic gates. Additionally, much like quantum dots and photonic crystals, it will be shown how microresonators offer an alternative method for creating engineerable materials with designer linear and nonlinear responses tailored for advanced functionalities operating at ultrafast speeds and compact scales. This is the first detailed text on the theory, fabrication, and applications of optical microresonators, and will be found useful by both graduate students and researchers. With an emphasis on building intuition with distilled equations and graphical illustratio...

  1. DWDM DFB LD fabricated by nanoimprint process

    Science.gov (United States)

    Liu, Wen; Wang, Lei; Zhou, Ning; Zhang, Yiwen; Qiu, Fei; Xu, Zhimou

    2011-02-01

    DFB LDs are key components in DWDM optical network. Now they are very expensive because the feedback grating period has to be controlled with very high accuracy and EBL is currently the most popular solution. We propose a high throughput, low cost NIL process based on a large stamp fabricated by SFIL and soft stamp pattern transfer method. DFB chips on 30mm*30mm area were manufactured with both good uniformity and performance. 13 ITU channels from 1540nm to 1560nm of 200GHz space are made. Our results show NIL has high potential to become another popular technology for DFB LD production, this cost effective and high efficiency manufacture solution may yield a significant impact to the future optical communication industry development.

  2. Reusable Component Services

    Data.gov (United States)

    U.S. Environmental Protection Agency — The Reusable Component Services (RCS) is a super-catalog of components, services, solutions and technologies that facilitates search, discovery and collaboration in...

  3. Experiences in the fabrication of aluminium clad metallic uranium fuel

    International Nuclear Information System (INIS)

    Vijayaraghavan, R.

    1989-01-01

    With a view to achieve self-sufficiency and self-reliance in the fabrication of metallic natural uranium fuel, a full fledged fuel fabrication facility was set up in 1958. Based on the then technical information available and the development work carried out, a flow-sheet for the fabrication of metallic uranium fuel, starting from uranium ingots, was worked out and the first fuel element was successfully fabricated in June 1959. More than half the first charge for the initial criticality of CIRUS, a 40 MWt research reactor at Trombay, was fabricated and supplied. Since then, this facility has been regularly catering to the replacement fuel and component requirements for CIRUS. The fuel for Dhruva, a 100 MWt research reactor at Trombay, is in the form of a cluster consisting of 7 fuel pins as compared to the rigid single fuel element for CIRUS. The fabrication process chosen for making this fuel is more or less on the same lines as that has been followed for CIRUS fuel. However, because of the smaller diameter of uranium metal rod, higher length to diameter ratio, configurations of fins on aluminium sheaths, cluster assembly etc., extensive development work was required to be undertaken for optimising various production parameters. Several prototype fuel clusters of different designs were made and subjected to rigorous out-of-pile and in-pile testing. Based on the reliable satisfactory performance, type II-B SPT cluster design was finally frozen for production. Stringent quality control is of prime importance in ensuring good performance of the fuel in the reactor. Hence, appropriate quality control measures have been adopted at various stages of fuel fabrication to ensure conformance with the specifications. (author) 9 refs., 11 figs., 1 tab

  4. SRF Cavity Fabrication and Materials

    CERN Document Server

    Singer, W

    2014-07-17

    The technological and metallurgical requirements of material for highgradient superconducting cavities are described. High-purity niobium, as the preferred metal for the fabrication of superconducting accelerating cavities, should meet exact specifications. The content of interstitial impurities such as oxygen, nitrogen, and carbon must be below 10μg/g. The hydrogen content should be kept below 2μg/g to prevent degradation of the Q-value under certain cool-down conditions. The material should be free of flaws (foreign material inclusions or cracks and laminations) that can initiate a thermal breakdown. Defects may be detected by quality control methods such as eddy current scanning and identified by a number of special methods. Conventional and alternative cavity fabrication methods are reviewed. Conventionally, niobium cavities are fabricated from sheet niobium by the formation of half-cells by deep drawing, followed by trim machining and Electron-Beam Welding (EBW). The welding of half-cells is a delicate...

  5. Software component quality evaluation

    Science.gov (United States)

    Clough, A. J.

    1991-01-01

    The paper describes a software inspection process that can be used to evaluate the quality of software components. Quality criteria, process application, independent testing of the process and proposed associated tool support are covered. Early results indicate that this technique is well suited for assessing software component quality in a standardized fashion. With automated machine assistance to facilitate both the evaluation and selection of software components, such a technique should promote effective reuse of software components.

  6. Fabrication Flaw Density and Distribution in Weld Repairs

    International Nuclear Information System (INIS)

    Doctor, Steven R.

    2009-01-01

    The Pacific Northwest National Laboratory (PNNL) is developing a generalized flaw distribution for the population of nuclear reactor pressure vessels and for piping welds in the U. S. operating reactors. The purpose of the generalized flaw distribution is to predict component-specific flaw densities. The estimates of fabrication flaws are intended for use in fracture mechanics structural integrity assessments. Structural integrity assessments, such as estimating the frequency of loss-of-coolant accidents, are performed by computer codes that require, as input, accurate estimates of flaw densities. Welds from four different cancelled reactor pressure vessels and a collection of archived pipes have been studied to develop empirical estimates of fabrication flaw densities. This paper describes the fabrication flaw distribution and characterization in the repair weld metal of vessels and piping. This work indicates that large flaws occur in these repairs which are complex in composition and sometimes include cracks on the ends of the repair cavities. Parametric analysis using an exponential fit is performed on the data. Construction records where available were reviewed. It is difficult to make conclusions due to the limited number of construction records reviewed. However, the records reviewed to date show a significant change in repair frequency over the years when the components in this study were fabricated. A description of repair flaw morphology is provided with a discussion of fracture mechanics significance.

  7. Reactor component automatic grapple

    International Nuclear Information System (INIS)

    Greenaway, P.R.

    1982-01-01

    A grapple for handling nuclear reactor components in a medium such as liquid sodium which, upon proper seating and alignment of the grapple with the component as sensed by a mechanical logic integral to the grapple, automatically seizes the component. The mechanical logic system also precludes seizure in the absence of proper seating and alignment. (author)

  8. Principal component analysis

    NARCIS (Netherlands)

    Bro, R.; Smilde, A.K.

    2014-01-01

    Principal component analysis is one of the most important and powerful methods in chemometrics as well as in a wealth of other areas. This paper provides a description of how to understand, use, and interpret principal component analysis. The paper focuses on the use of principal component analysis

  9. Proof of fatigue strength of nuclear components part II: Numerical fatigue analysis for transient stratification loading considering environmental effects

    International Nuclear Information System (INIS)

    Krätschmer, D.; Roos, E.; Schuler, X.; Herter, K.-H.

    2012-01-01

    For the construction, design and operation of nuclear components and systems the appropriate technical codes and standards provide detailed analysis procedures which guarantee a reliable behaviour of the structural components throughout the specified lifetime. Especially for cyclic stress evaluation the different codes and standards provide different fatigue analyses procedures to be performed considering the various mechanical and thermal loading histories and geometric complexities of the components. To consider effects of light water reactor coolant environments, new design curves included in report NUREG/CR-6909 for austenitic stainless steels and for low alloy steels have been presented. For the usage of these new design curves an environmental fatigue correction factor for incorporating environmental effects has to be calculated and used. The application of this environmental correction factor to a fatigue analysis of a nozzle with transient stratification loads, derived by in-service monitoring, has been performed. The results are used to compare with calculated usage factors, based on design curves without taking environmental effects particularly into account. - Highlights: ► We model an nozzle for fatigue analysis und mechanical and thermal loading conditions. ► A simplified as well as a general elastic–plastic fatigue analysis considering environmental effects is performed. ► The influence of different factors calculating the environmental factor F en are shown. ► The presented numerical evaluation methodology allows the consideration of all relevant parameters to assess lifetime.

  10. MQXFS1 Quadrupole Fabrication Report

    Energy Technology Data Exchange (ETDEWEB)

    Ambrosio, G. [Fermi National Accelerator Lab. (FNAL), Batavia, IL (United States); Anerella, M. [Brookhaven National Lab. (BNL), Upton, NY (United States); Bossert, R. [European Organization for Nuclear Research (CERN), Geneva (Switzerland); Cavanna, E. [European Organization for Nuclear Research (CERN), Geneva (Switzerland); Cheng, D. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Chlachidize, G. [Fermi National Accelerator Lab. (FNAL), Batavia, IL (United States); Cooley, L. [Fermi National Accelerator Lab. (FNAL), Batavia, IL (United States); Dietderich, D. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Felice, H. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Ferracin, P. [European Organization for Nuclear Research (CERN), Geneva (Switzerland); Ghosh, A. [Brookhaven National Lab. (BNL), Upton, NY (United States); Hafalia, R. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Holik, E. F. [Fermi National Accelerator Lab. (FNAL), Batavia, IL (United States); Bermudez, S. Izquierdo [European Organization for Nuclear Research (CERN), Geneva (Switzerland); Juchno, M. [European Organization for Nuclear Research (CERN), Geneva (Switzerland); Krave, S. [Fermi National Accelerator Lab. (FNAL), Batavia, IL (United States); Marchevsky, M. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Muratore, J. [Brookhaven National Lab. (BNL), Upton, NY (United States); Nobrega, F. [Fermi National Accelerator Lab. (FNAL), Batavia, IL (United States); Pan, H. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Perez, J. C. [European Organization for Nuclear Research (CERN), Geneva (Switzerland); Pong, I. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Prestemon, S. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Ravaioli, E. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Sabbi, G. L. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Santini, C. [Fermi National Accelerator Lab. (FNAL), Batavia, IL (United States); Schmalzle, J. [Brookhaven National Lab. (BNL), Upton, NY (United States); Stoynev, S. [Fermi National Accelerator Lab. (FNAL), Batavia, IL (United States); Strauss, T. [Fermi National Accelerator Lab. (FNAL), Batavia, IL (United States); Vallone, G. [European Organization for Nuclear Research (CERN), Geneva (Switzerland); Wanderer, P. [Brookhaven National Lab. (BNL), Upton, NY (United States); Wang, X. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Yu, M. [Fermi National Accelerator Lab. (FNAL), Batavia, IL (United States)

    2017-07-16

    This report presents the fabrication and QC data of MQXFS1, the first short model of the low-beta quadrupoles (MQXF) for the LHC High Luminosity Upgrade. It describes the conductor, the coils, and the structure that make the MQXFS1 magnet. Qualification tests and non-conformities are also presented and discussed. The fabrication of MQXFS1 was started before the finalization of conductor and coil design for MQXF magnets. Two strand design were used (RRP 108/127 and RRP 132/169). Cable and coil cross-sections were “first generation”.

  11. MQXFS1 Quadrupole Fabrication Report

    International Nuclear Information System (INIS)

    Ambrosio, G.; Anerella, M.; Bossert, R.; Cavanna, E.; Cheng, D.; Chlachidize, G.; Cooley, L.; Dietderich, D.; Felice, H.; Ferracin, P.; Ghosh, A.; Hafalia, R.; Holik, E. F.; Bermudez, S. Izquierdo; Juchno, M.; Krave, S.; Marchevsky, M.; Muratore, J.; Nobrega, F.; Pan, H.; Perez, J. C.; Pong, I.; Prestemon, S.; Ravaioli, E.; Sabbi, G. L.; Santini, C.; Schmalzle, J.; Stoynev, S.; Strauss, T.; Vallone, G.; Wanderer, P.; Wang, X.; Yu, M.

    2017-01-01

    This report presents the fabrication and QC data of MQXFS1, the first short model of the low-beta quadrupoles (MQXF) for the LHC High Luminosity Upgrade. It describes the conductor, the coils, and the structure that make the MQXFS1 magnet. Qualification tests and non-conformities are also presented and discussed. The fabrication of MQXFS1 was started before the finalization of conductor and coil design for MQXF magnets. Two strand design were used (RRP 108/127 and RRP 132/169). Cable and coil cross-sections were “first generation”.

  12. Advanced fabrication of hyperbolic metamaterials

    DEFF Research Database (Denmark)

    Shkondin, Evgeniy; Sukham, Johneph; Panah, Mohammad Esmail Aryaee

    2017-01-01

    Hyperbolic metamaterials can provide unprecedented properties in accommodation of high-k (high wave vector) waves and enhancement of the optical density of states. To reach such performance the metamaterials have to be fabricated with as small imperfections as possible. Here we report on our...... advances in two approaches in fabrication of optical metamaterials. We deposit ultrathin ultrasmooth gold layers with the assistance of organic material (APTMS) adhesion layer. The technology supports the stacking of such layers in a multiperiod construction with alumina spacers between gold films, which...

  13. Innovative Approaches to Large Component Packaging

    International Nuclear Information System (INIS)

    Freitag, A.; Hooper, M.; Posivak, E.; Sullivan, J.

    2006-01-01

    Radioactive waste disposal often times requires creative approaches in packaging design, especially for large components. Innovative design techniques are required to meet the needs for handling, transporting, and disposing of these large packages. Large components (i.e., Reactor Pressure Vessel (RPV) heads and even RPVs themselves) require special packaging for shielding and contamination control, as well as for transport and disposal. WMG Inc designed and used standard packaging for RPV heads without control rod drive mechanisms (CRDMs) attached for five RPV heads and has also more recently met an even bigger challenge and developed the innovative Intact Vessel Head Transport System (IVHTS) for RPV heads with CRDMs intact. This packaging system has been given a manufacturer's exemption by the United States Department of Transportation (USDOT) for packaging RPV heads. The IVHTS packaging has now been successfully used at two commercial nuclear power plants. Another example of innovative packaging is the large component packaging that WMG designed, fabricated, and utilized at the West Valley Demonstration Project (WVDP). In 2002, West Valley's high-level waste vitrification process was shut down in preparation for D and D of the West Valley Vitrification Facility. Three of the major components of concern within the Vitrification Facility were the Melter, the Concentrate Feed Makeup Tank (CFMT), and the Melter Feed Holdup Tank (MFHT). The removal, packaging, and disposition of these three components presented significant radiological and handling challenges for the project. WMG designed, fabricated, and installed special packaging for the transport and disposal of each of these three components, which eliminated an otherwise time intensive and costly segmentation process that WVDP was considering. Finally, WMG has also designed and fabricated special packaging for both the Connecticut Yankee (CY) and San Onofre Nuclear Generating Station (SONGS) RPVs. This paper

  14. Novel Amalgams for In-Space Fabrication of Replacement Parts

    Science.gov (United States)

    Cochran, Calvin T.; Van Hoose, James R.; Grugel, R. N.

    2012-01-01

    Being able to fabricate replacement parts during extended space flight missions precludes the weight, storage volume, and speculation necessary to accommodate spares. Amalgams, widely used in dentistry, are potential candidates for fabricating parts in microgravity environments as they are moldable, do not require energy for melting, and do not pose fluid handling problems. Unfortunately, amalgams have poor tensile strength and the room temperature liquid component is mercury. To possibly resolve these issues a gallium-indium alloy was substituted for mercury and small steel fibers were mixed in with the commercial alloy powder. Subsequent microscopic examination of the novel amalgam revealed complete bonding of the components, and mechanical testing of comparable samples showed those containing steel fibers to have a significant improvement in strength. Experimental procedures, microstructures, and test results are presented and discussed in view of further improving properties.

  15. Experience in developing countries in monitoring procurement and fabrication

    International Nuclear Information System (INIS)

    Csik, B.J.

    1977-01-01

    Owner's responsibility in monitoring procurement and fabrication. Monitoring ectivity, tasks, knowledge and personnel requirements, scope and organization. Contractual arrangements, commitments, responsibilities, rights and obligations. Domestic and foreign supplies. Staff and consultants. Experience in developing countries. Problem areas: availability of qualified staff, organization, methodology standards, codes, specifications, availability and flow of information, language, technical knowledge, access to suppliers' facilities, delays, nuclear safety related components, modifications and additionals. (orig.) [de

  16. Fabrication of metallic glass structures

    Science.gov (United States)

    Cline, C.F.

    1983-10-20

    Amorphous metal powders or ribbons are fabricated into solid shapes of appreciable thickness by the application of compaction energy. The temperature regime wherein the amorphous metal deforms by viscous flow is measured. The metal powders or ribbons are compacted within the temperature regime.

  17. The Danish fabricated metal industry:

    DEFF Research Database (Denmark)

    Hansen, Teis

    2010-01-01

    . This is less the case for low-tech industries, but their economic importance continues to be large, however. It is thus interesting to analyse how they manage to remain competitive. The analysis focuses on a case study of the fabricated metal industry by identifying the innovation strategies followed by firms...

  18. Fabrication of green polymeric membranes

    KAUST Repository

    Kim, Dooli

    2017-06-16

    Provided herein are methods of fabricating membranes using polymers with functionalized groups such as sulfone (e.g., PSf and PES), ether (e.g., PES), acrylonitrile (e.g., PAN), fluoride(e.g., pvdf and other fluoropolymers), and imide (e.g., extem) and ionic liquids. Also provided are membranes made by the provided methods.

  19. Transverse permeability of woven fabrics

    NARCIS (Netherlands)

    Grouve, Wouter Johannes Bernardus; Akkerman, Remko; Loendersloot, Richard; van den Berg, S.

    2008-01-01

    The transverse permeability is an essential input in describing the consolidation process of CETEX® laminates. A two-dimensional, finite difference based, Stokes flow solver has been developed to determine the mesoscopic permeability of arbitrary fabric structures. The use of a multigrid solver

  20. Microfluidic fabrication of plasmonic microcapsules

    NARCIS (Netherlands)

    Wang, J.; Jin, Mingliang; Eijkel, Jan C.T.; van den Berg, Albert; Zhou, G.F.; Shui, L.L.

    2016-01-01

    This paper presents the plasmonic microcapsules with well-ordered nanoparticles embedded in polymer network fabricated by using a microfluidic device. The well-ordered nanoparticle arrays on the microcapsule form high-density uniform “hot-spots‿ with a deposited metal film, on which the localized

  1. Fabrication Aware Form-finding

    DEFF Research Database (Denmark)

    Egholm Pedersen, Ole; Larsen, Niels Martin; Pigram, Dave

    2014-01-01

    This paper describes a design and construction method that combines two distinct material systems with fabrication aware form-finding and file-to-factory workflows. The method enables the fluent creation of complex materially efficient structures comprising high populations of geometrically uniqu...

  2. Development of Prototype HTS Components for Magnetic Suspension Applications

    Science.gov (United States)

    Haldar, P.; Hoehn, J., Jr.; Selvamanickam, V.; Farrell, R. A.; Balachandran, U.; Iyer, A. N.; Peterson, E.; Salazar, K.

    1996-01-01

    We have concentrated on developing prototype lengths of bismuth and thallium based silver sheathed superconductors by the powder-in-tube approach to fabricate high temperature superconducting (HTS) components for magnetic suspension applications. Long lengths of mono and multi filament tapes are presently being fabricated with critical current densities useful for maglev and many other applications. We have recently demonstrated the prototype manufacture of lengths exceeding 1 km of Bi-2223 multi filament conductor. Long lengths of thallium based multi-filament conductor have also been fabricated with practical levels of critical current density and improved field dependence behavior. Test coils and magnets have been built from these lengths and characterized over a range of temperatures and background fields to determine their performance. Work is in progress to develop, fabricate and test HTS windings that will be suitable for magnetic suspension, levitation and other electric power related applications.

  3. Electronic components with yttrium- and bismuth-based high-Tc superconductors

    International Nuclear Information System (INIS)

    Daginnus, M.; Guettler, B.

    1992-01-01

    This project investigates the fabrication of microwave components by use of high-Tc superconductors. Detailed descriptions are given of the manufacturing and use of active Y-Ba-Cu-O components. The surface resistance of thin films used in high-quality passive microwave components such as resonators and filters is measured and optimized. (orig./MM) [de

  4. Fabrication of CANDU dupic fuel

    International Nuclear Information System (INIS)

    Sullivan, J.D.; Ryz, M.A.; Lee, J.W.

    1999-01-01

    An important new fuel cycle that exploits the synergism between CANDU and pressurized-water reactors (PWRs) is the Direct Use of spent PWR Fuel in CANDU (DUPIC). In this fuel cycle, spent PWR fuel is reconfigured, using only dry processing techniques, to make it compatible with a CANDU reactor. The dry processing technique is inherently simpler than wet chemical processing techniques used for recycling spent fuel. Actinides and fission products are retained in the fuel, so that DUPIC fuel is highly radioactive, affording the fuel cycle a high degree of proliferation resistance. AECL's project to develop the fuel cycle has now progressed to the stage of fabricating DUPIC fuel elements for irradiation testing in a research reactor. The goal of this phase of the project is to demonstrate that the DUPIC fuel cycle is technically feasible. A major part of the technical feasibility study is demonstration of the irradiation performance of DUPIC fuel under CANDU conditions. Spent PWR fuel has been subjected to the oxidation and reduction of oxide fuels (OREOX) process, and the resulting powder has been fabricated into CANDU-quality pellets. The DUPIC pellets have been loaded into fuel elements for irradiation testing in the NRU research reactor at the Chalk River Laboratories. The fabrication stages included spent fuel decladding, powder production using the OREOX process, powder milling (to improve sinterability), pellet pressing, sintering, centreless grinding, element loading and element welding. This paper details the fabrication of the DUPIC pellets and elements and initial results of their characterization. The equipment used for fabrication of the DUPIC fuel elements is described, and the irradiation plan for these elements is also outlined. (author)

  5. Ground Motion Prediction Atop Geometrically Complex Sedimentary Basins - The Dead Sea Basin

    Science.gov (United States)

    Shani-Kadmiel, S.; Tsesarsky, M.; Louie, J. N.; Gvirtzman, Z.

    2014-12-01

    The Dead Sea Transform (DST) is the source for some of the largest earthquakes in the eastern Mediterranean. Several deep and structurally complex sedimentary basins are associated with the DST. These basins are up to 10 km deep and typically bounded by active fault zones. The low seismicity of the DST combined with the limited instrumental coverage of the seismic network in the area result in a critical knowledge gap. Therefore, it is necessary to complement the limited instrumental data with synthetic data based on computational modeling, in order to study the effects of earthquake ground motion in these sedimentary basins. We performed a 2D ground-motion analysis in the Dead Sea Basin (DSB) using a finite-difference code. Results indicate a complex pattern of ground motion amplification affected by the geometric features in the basin. To distinguish between the individual contributions of each geometrical feature in the basin, we developed a semiquantitative decomposition approach. This approach enabled us to interpret the DSB results as follows: (1) Ground-motion amplification as a result of resonance occurs basin-wide due to a high impedance contrast at the base of the uppermost layer; (2) Steep faults generate a strong edge-effect that further ampli- fies ground motions; (3) Sub-basins cause geometrical focusing that may significantly amplify ground motions; and (4) Salt diapirs diverge seismic energy and cause a de- crease in ground-motion amplitude. We address the significance of ground motion amplification due to geometrical focusing via an analytical and numerical study. We show that effective geometrical focusing occurs for a narrow set of eccentricities and velocity ratios, where seismic energy is converged to a region of ±0.5 km from surface. This mechanism leads to significant ground motion amplification at the center of the basin, up to a factor of 3; frequencies of the modeled spectrum are amplified up to the corner frequency of the source.

  6. Detection of inhomogeneities in membrane ohmic resistance in geometrically complex systems

    DEFF Research Database (Denmark)

    Svirskis, G; Hounsgaard, J; Gutman, A

    2000-01-01

    DC field-evoked transients in arbitrarily shaped neurons and syncytia were analyzed theoretically. In systems with homogeneous passive membrane properties, the transients develop much faster than the membrane discharges. Conductance of the proximal membrane could be larger due to the injury impos...

  7. Accurate Estimation of the Intrinsic Dimension Using Graph Distances: Unraveling the Geometric Complexity of Datasets

    Science.gov (United States)

    Granata, Daniele; Carnevale, Vincenzo

    2016-01-01

    The collective behavior of a large number of degrees of freedom can be often described by a handful of variables. This observation justifies the use of dimensionality reduction approaches to model complex systems and motivates the search for a small set of relevant “collective” variables. Here, we analyze this issue by focusing on the optimal number of variable needed to capture the salient features of a generic dataset and develop a novel estimator for the intrinsic dimension (ID). By approximating geodesics with minimum distance paths on a graph, we analyze the distribution of pairwise distances around the maximum and exploit its dependency on the dimensionality to obtain an ID estimate. We show that the estimator does not depend on the shape of the intrinsic manifold and is highly accurate, even for exceedingly small sample sizes. We apply the method to several relevant datasets from image recognition databases and protein multiple sequence alignments and discuss possible interpretations for the estimated dimension in light of the correlations among input variables and of the information content of the dataset. PMID:27510265

  8. CompSim: Cross sectional modeling of geometrical complex and inhomogeneous slender structures

    Directory of Open Access Journals (Sweden)

    Turaj Ashuri

    2017-01-01

    Full Text Available Many engineering disciplines require a fast and accurate estimate of structural properties in initial design phase for analysis and optimization studies. This paper presents an open-source computational code named CompSim to develop the structural properties of complex geometries with inhomogeneous materials. Weighted average technique is used to compute properties such as stiffness coefficients, area moment of inertia, and mass distribution. The accuracy of the code is evaluated for a multi-layer composite cross-section. As an illustrative example, the properties of the 20 MW common research wind turbine model are computed and presented. The code helps users to develop and optimize an initial structure in conceptual and preliminary design for further analysis in detailed design phase.

  9. CompSim: Cross sectional modeling of geometrical complex and inhomogeneous slender structures

    Science.gov (United States)

    Ashuri, Turaj; Zhang, Jie

    Many engineering disciplines require a fast and accurate estimate of structural properties in initial design phase for analysis and optimization studies. This paper presents an open-source computational code named CompSim to develop the structural properties of complex geometries with inhomogeneous materials. Weighted average technique is used to compute properties such as stiffness coefficients, area moment of inertia, and mass distribution. The accuracy of the code is evaluated for a multi-layer composite cross-section. As an illustrative example, the properties of the 20 MW common research wind turbine model are computed and presented. The code helps users to develop and optimize an initial structure in conceptual and preliminary design for further analysis in detailed design phase.

  10. CompSim: Cross sectional modeling of geometrical complex and inhomogeneous slender structures

    OpenAIRE

    Turaj Ashuri; Jie Zhang

    2017-01-01

    Many engineering disciplines require a fast and accurate estimate of structural properties in initial design phase for analysis and optimization studies. This paper presents an open-source computational code named CompSim to develop the structural properties of complex geometries with inhomogeneous materials. Weighted average technique is used to compute properties such as stiffness coefficients, area moment of inertia, and mass distribution. The accuracy of the code is evaluated for a multi-...

  11. Geometrically complex 3D-printed phantoms for diffuse optical imaging.

    Science.gov (United States)

    Dempsey, Laura A; Persad, Melissa; Powell, Samuel; Chitnis, Danial; Hebden, Jeremy C

    2017-03-01

    Tissue-equivalent phantoms that mimic the optical properties of human and animal tissues are commonly used in diffuse optical imaging research to characterize instrumentation or evaluate an image reconstruction method. Although many recipes have been produced for generating solid phantoms with specified absorption and transport scattering coefficients at visible and near-infrared wavelengths, the construction methods are generally time-consuming and are unable to create complex geometries. We present a method of generating phantoms using a standard 3D printer. A simple recipe was devised which enables printed phantoms to be produced with precisely known optical properties. To illustrate the capability of the method, we describe the creation of an anatomically accurate, tissue-equivalent premature infant head optical phantom with a hollow brain space based on MRI atlas data. A diffuse optical image of the phantom is acquired when a high contrast target is inserted into the hollow space filled with an aqueous scattering solution.

  12. Lab-on-chip components for molecular detection

    Science.gov (United States)

    Adam, Tijjani; Dhahi, Th S.; Mohammed, Mohammed; Hashim, U.; Noriman, N. Z.; Dahham, Omar S.

    2017-09-01

    We successfully fabricated Lab on chip components and integrated for possible use in biomedical application. The sensor was fabricated by using conventional photolithography method integrated with PDMS micro channels for smooth delivery of sample to the sensing domain. The sensor was silanized and aminated with 3-Aminopropyl triethoxysilane (APTES) to functionalize the surface with biomolecules and create molecular binding chemistry. The resulting Si-O-Si- components were functionalized with oligonucleotides probe of HPV, which interacted with the single stranded HPV DNA target to create a field across on the device. The fabrication, immobilization and hybridization processes were characterized with current voltage (I-V) characterization (KEITHLEY, 6487). The sensor show selectivity for the HPV DNA target in a linear range from concentration 0.1 nM to 1 µM. This strategy presented a simple, rapid and sensitive platform for HPV detection and would become a powerful tool for pathogenic microorganisms screening in clinical diagnosis.

  13. Supply chain components

    Directory of Open Access Journals (Sweden)

    Vieraşu, T.

    2011-01-01

    Full Text Available In this article I will go through three main logistics components, which are represented by: transportation, inventory and facilities, and the three secondary logistical components: information, production location, price and how they determine performance of any supply chain. I will discuss then how these components are used in the design, planning and operation of a supply chain. I will also talk about some obstacles a supply chain manager may encounter.

  14. Supply chain components

    OpenAIRE

    Vieraşu, T.; Bălăşescu, M.

    2011-01-01

    In this article I will go through three main logistics components, which are represented by: transportation, inventory and facilities, and the three secondary logistical components: information, production location, price and how they determine performance of any supply chain. I will discuss then how these components are used in the design, planning and operation of a supply chain. I will also talk about some obstacles a supply chain manager may encounter.

  15. Hot gas path component

    Science.gov (United States)

    Lacy, Benjamin Paul; Kottilingam, Srikanth Chandrudu; Porter, Christopher Donald; Schick, David Edward

    2017-09-12

    Various embodiments of the disclosure include a turbomachine component. and methods of forming such a component. Some embodiments include a turbomachine component including: a first portion including at least one of a stainless steel or an alloy steel; and a second portion joined with the first portion, the second portion including a nickel alloy including an arced cooling feature extending therethrough, the second portion having a thermal expansion coefficient substantially similar to a thermal expansion coefficient of the first portion, wherein the arced cooling feature is located within the second portion to direct a portion of a coolant to a leakage area of the turbomachine component.

  16. CORE COMPONENT POT

    Energy Technology Data Exchange (ETDEWEB)

    MARTIN RL; OMBERG RP

    1975-12-19

    The core component pot is an open top vessel used to hold both new and irradiated core components for storage in the IDS and for holding the components submerged in sodium while being trasported inside CLEM. The top of the CCP is equipped with a grapple lip which is engaged by the hoisting grapples. Heat for maintaining the preheat of new components and dissipation of decay heat of irradiated fuel assemblies is conducted between the wall of the pot and the surrounding environment by thermal radiation and convection.

  17. General requirements for pressure-retaining systems and components in CANDU nuclear power plants

    International Nuclear Information System (INIS)

    1991-11-01

    This standard specifies the general requirements for the design, fabrication and installation of pressure-retaining systems, components, and their supports in CANDU nuclear power plants. (16 figs., 2 tabs., 25 refs.)

  18. Pin Component Technology (V1.0) and Its C Interface

    National Research Council Canada - National Science Library

    Hissam, Scott; Ivers, James; Plakosh, Daniel; Wallnau, Kurt C

    2005-01-01

    .... Pin implements the container idiom for software components. Containers provide a pre-fabricated "shell" in which custom code executes and through which all interactions between custom code and its external environment are mediated...

  19. Fabrication drawings of fuel pins for FUJI project among PSI, JNC and NRG. Revised version 2

    International Nuclear Information System (INIS)

    Ozawa, Takayuki; Nakazawa, Hiroaki; Abe, Tomoyuki; Nagayama, Masahiro

    2002-10-01

    Irradiation tests and post-irradiation examinations in the framework of JNC-PSI-NRG collaboration project will be performed in 2003-2005. Irradiation fuel pins will be fabricated by the middle of 2003. The fabrication procedure for irradiation fuel pins has been started in 2001. Several fabrication tests and qualification tests in JNC and PSI (Paul Scherrer Institut, Switzerland) have been performed before the fuel pin fabrication. According to the design assignment between PSI and JNC in the frame of this project, PSI should make specification documents for the fuel pellet, the sphere-pac fuel particles, the vipac fuel fragments, and the fuel segment fabrication. JNC should make the fabrication drawings for irradiation pins. JNC has been performed the fuel design in cooperation with PSI and NRG (Nuclear Research and Consultancy Group, Holland). In this project, the pelletized fuel, the sphere-pac fuel, and the vipac fuel will be simultaneously irradiated on HFR (High Flux Reactor, Holland). The fabrication drawings have been made under the design assignment with PSI, and consist of the drawings of MOX pellet, thermal insulator pellet, pin components, fuel segments, and the constructed pin. The fabrication drawings were approved in October 2001, but after that, the optimization of specifications was discussed and agreed among all partners. According to this agreement, the fabrication drawings were revised in January 2002. After the earlier revision, the shape of particle retainer to be made by PSI was modified from its drawing beforehand delivered. In this report, the fabrication drawings revised again will be shown, and the fabrication procedure (welding Qualification Tests) will be modified in accordance with the result of discussion on the 3rd technical meeting held in September 2002. These design works have been performed in Fuel Design and Evaluation Group, Plutonium Fuel Fabrication Division, Plutonium Fuel Center under the commission of Plutonium Fuel

  20. Laser target fabrication, structure and method for its fabrication

    Science.gov (United States)

    Farnum, Eugene H.; Fries, R. Jay

    1985-01-01

    The disclosure is directed to a laser target structure and its method of fabrication. The target structure comprises a target plate containing an orifice across which a pair of crosshairs are affixed. A microsphere is affixed to the crosshairs and enclosed by at least one hollow shell comprising two hemispheres attached together and to the crosshairs so that the microsphere is juxtapositioned at the center of the shell.

  1. Feasibility and Testing of Additive Manufactured Components

    Energy Technology Data Exchange (ETDEWEB)

    Dehoff, Ryan R [ORNL; Hummelt, Ed [Eaton Corporation; Solovyeva, Lyudmila [Eaton Corporation

    2016-09-01

    This project focused on demonstrating the ability to fabricate two parts with different geometry: an arc flash interrupter and a hydraulic manifold. Eaton Corporation provided ORNL solid models, information related to tolerances and sensitive parameters of the parts and provided testing and evaluation. ORNL successfully manufactured both components, provided cost models of the manufacturing (materials, labor, time and post processing) and delivered test components for Eaton evaluation. The arc flash suppressor was fabricated using the Renishaw laser powder bed technology in CoCrMo while the manifold was produced from Ti-6Al-4V using the Arcam electron beam melting technology. These manufacturing techniques were selected based on the design and geometrical tolerances required. A full-scale manifold was produced on the Arcam A2 system (nearly 12 inches tall). A portion of the manifold was also produced in the Arcam Q10 system. Although a full scale manifold could not be produced in the system, a full scale manifold is expected to have similar material properties, geometric accuracy, and surface finish as could be fabricated on an Arcam Q20 system that is capable of producing four full scale manifolds in a production environment. In addition to the manifold, mechanical test specimens, geometric tolerance artifacts, and microstructure samples were produced alongside the manifold. The development and demonstration of these two key components helped Eaton understand the impact additive manufacturing can have on many of their existing products. By working within the MDF and leveraging ORNL’s manufacturing and characterization capabilities, the work will ensure the rapid insertion and commercialization of this technology.

  2. Preparation of activated carbon fabrics from cotton fabric precursor

    Science.gov (United States)

    Salehi, R.; Dadashian, F.; Abedi, M.

    2017-10-01

    The preparation of activated carbon fabrics (ACFs) from cotton fabric was performed by chemical activation with phosphoric acid (H3PO4). The operation conditions for obtaining the ACFs with the highest the adsorption capacity and process yield, proposed. Optimized conditions were: impregnation ratio of 2, the rate of temperature rising of 7.5 °C min-1, the activation temperature of 500 °C and the activation time of 30 min. The ACFs produced under optimized conditions was characterized by scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDX). The surface area and pore volume of carbon nanostructures was characterized by BET nitrogen adsorption isotherm at 77 °K. The pore size distribution calculated from the desorption branch according to BJH method. The iodine number of the prepared ACFs was determined by titration at 30 °C based on the ASTM D4607-94. The results showed the improvement of porous structure, fabric shape, surface area (690 m2/g), total pore volume (0.3216 cm3/g), and well-preserved fibers integrity.

  3. Design criteria monograph for metal tanks and tank components

    Science.gov (United States)

    1975-01-01

    Significant elements in detail tank design are wall and end structures, weld joints at bulkhead and attachment junctures, and ports and access openings. Additional design considerations are influence and effect of fabrication processes on tank component design, and finally, testing and inspection that are required to establish confidence in tank design.

  4. Qualitative Investigation of Some Locally Produced Printed Fabrics ...

    African Journals Online (AJOL)

    The results obtained showed that the locally produced fabrics exhibited comparably better end – use performance characteristics in terms of fabric weight per square meter, fabric flammability, and linear density. While the foreign fabrics are better in terms of Crease recovery, fabric handle, fabric sett, fabric shrinkage, and ...

  5. Mechanical development for reliable reactor components

    International Nuclear Information System (INIS)

    Ross-Ross, P.A.; Metcalfe, R.

    1983-09-01

    The CANDU reactor has achieved worldwide distinction because of its reliable performance. To achieve this, special attention was given to the reliability and maintainability of components in the heavy water circuits. Development programs were initiated early in the history of the CANDU reactor to improve the effectiveness of pump seals, valves, and static seals because of unacceptable performance of the commercial equipment then available. As a result, pump seals with a five year life now appear achievable, and valves and static seals are no longer a significant concern in CANDU reactors. Increasing effort is being given remotely operated tools and fabrication systems for radioactive environments

  6. Nylon fabric reinforced natural rubber compound

    Science.gov (United States)

    Kamal, Mazlina Mustafa; Ismail, Ismaliza

    2017-12-01

    Rubber fabric coated is a unique rubber-textile composite, in which technical textile acts as reinforcing material and strength providing material. In rubber textile composite, rubber to fabric adhesion plays the most critical role for determining assembly process and ultimate strength of product. A vulcanisable adhesive for rubber to fabric fabrication of composite material was developed which compatible with rubber as well as fabric. Evaluation of bonding system with respect to peel strength, shear adhesion strength and weave pattern of fabrics were the major determining criteria for selection and optimization of fabric for rubber hose application. Thus adhesive Cohedure with characteristics of high adhesive strength in Natural Rubber Polyester Fabric compound has been developed.

  7. Nanosensor Fabrication with 3D Manufacturing Techniques

    Data.gov (United States)

    National Aeronautics and Space Administration — We use 3D manufacturing techniques to fabricate sensors based on nanomaterials. We use 3D manufacturing techniques to fabricate sensors based on nanomaterials. This...

  8. Paving fabrics for reducing reflective cracking

    Science.gov (United States)

    1991-11-01

    This research effort was part of ADOT's New Product Evaluation Program. The objective was to evaluate the construction and field performances of three commercially available paving fabrics; Paveprep, Glassgrid, and Tapecoat. The fabrics were designed...

  9. Fabric quality issues related to apparel merchandising

    CSIR Research Space (South Africa)

    Das, Sonali

    2015-02-01

    Full Text Available The objectives of this study are to develop an understanding of fabric quality related issues and research gaps relevant to apparel manufacturing and merchandising within the South African context. The specific focus is on fabric objective...

  10. Design principles and overall aspects to proof the integrity of pressurized components

    International Nuclear Information System (INIS)

    Roos, E.; Herter, K.-H.; Schuler, X.

    2005-01-01

    Technical codes and standards used for the construction, design and operation of nuclear components and systems provides the material data required, detailed stress analysis procedures and a design philosophy which guarantees a reliable behaviour of the systems, structures and components (SSC) throughout the specified life time. It is important that the design concept accounts for most possible damage mechanisms and failure modes and provides rational margins of safety against each type of damage mechanism and failure mode. The design criteria according to codes and standards are the basic rules upon which the mechanical behaviour of the SSC is based. For cyclic stress evaluation the different codes and standards provides fatigue analyses to be performed considering the various loading histories (mechanical and thermal loads) and geometric complexities of the SSC. Essentially the philosophy for the mechanical design in all of the codes and standards broadly encompasses the two approaches of Design-by-Rule (DBR) and Design-by-Analysis (DBA). Design-by-Experiment (DBE) and Design-by-Fracture Mechanics (DBFA) are in special cases additional possibilities for the design as well as for the proof of integrity of SSC. Based on the German Basis Safety Concept a general concept to ensure the integrity of pressurised components is developed. As a premise for a systematically approach it is indispensable to show that the as-built status of quality (actual material characteristics, actual as-built configurations, design, actual loading) is according to the requirements given in the guidelines and standards, to show that sufficient knowledge of possible failure mechanism (e.g. no inadmissible dynamic loading, no corrosion) is available and to show that the as-built status of quality can be guaranteed for the succeeding operation. The calculation methods and fracture mechanics approaches are verified by numerous experimental data. (authors)

  11. Towards Cognitive Component Analysis

    DEFF Research Database (Denmark)

    Hansen, Lars Kai; Ahrendt, Peter; Larsen, Jan

    2005-01-01

    Cognitive component analysis (COCA) is here defined as the process of unsupervised grouping of data such that the ensuing group structure is well-aligned with that resulting from human cognitive activity. We have earlier demonstrated that independent components analysis is relevant for representi...

  12. Components development in the EU

    International Nuclear Information System (INIS)

    2015-01-01

    In the Euratom Sixth Framework Programme (FP6) an integrated project IP-EUROTRANS (transmutation) is ongoing. One of this project’s objectives is to develop and assess structural materials and heavy liquid metal (HLM) lead–lead-bismuth technologies for transmutation systems, where the HLM is both the spallation material and the core coolant. This involves specification and fabrication of reference materials, their characterisation in HLM and in representative conditions (with and without irradiation environment) in order to provide the data base needed for design purposes (e.g. fuel cladding, in-vessel components, primary vessel, instrumentation, target container, beam window), thermalhydraulics, measurement techniques, large scale integral tests and PTA studies for the MEGAPIE spallation target of FP5. In particular the ongoing R&D for the subcritical reactors XT-ADS, cooled by LBE, and EFIT, cooled by pure lead are: – To provide necessary information for designers, as concerns both T91 and 316L steels in contact with LBE and lead. This R&D is aimed to: • Determine the creep, low cycle fatigue, relaxation (fatigue and creep) fatigue behaviour of T91 and 316L in contact with lead and LBE, both qualitatively and quantitatively; • Characterize their fracture resistance, once again both qualitatively and quantitatively; • Constitute reliable data base over a wide temperature range, attaining 550°C; • Determine the fracture mechanisms of both ferritic–martensitic and austenitic materials in contact with HLMs

  13. The fabrication of nuclear fuel

    International Nuclear Information System (INIS)

    D'Amore, Mead

    1987-01-01

    The chronology of fuel product and core management development over the past 25 years in the USA is explained. Nuclear fuel for Westinghouse reactors is made by converting enriched uranium hexafluoride (UF 6 ) into uranium dioxide (UO 2 ) powder. The powder is pressed into pellets which are loaded into zircalloy fuel tubes (typically over 14 million pellets in 50,952 rods). The fuel rods are arranged in fuel assemblies which are shipped to the reactor site (typically 193 fuel assemblies are needed for one 1000MWe reactor). Each stage of the fuel fabrication cycle (cladding manufacture, chemical conversion UF 6 - UO 2 , pellet production, fuel rod fabrication, grid assembly, skeleton assembly, fuel assembly) is described, with particular reference to the Westinghouse process and plant. (UK)

  14. Quality in the fabrication process

    International Nuclear Information System (INIS)

    Romano, A.; Aguirre, F.

    2010-01-01

    Enusa commitment to quality in the manufacture process materializes in the application of the most advanced product quality control technologies such as not-destructive inspection techniques, like artificial vision, X-ray or UT inspection, or process parameter statistical control systems. Quality inspectors are trained and certified by the main National Quality Organizations and receive periodic training under a formal company training program that constantly updates their qualification. Fabrication quality control reliability is based on a strategy that prioritizes redundancy of critical inspection equipment's and inspection personnel knowledge polyvalence. Furthermore, improvement in fabrication quality is obtained by a systematic application of the six sigma methodology where added value is created in projects integrating crosscutting company knowledge, reinforcing the global company vision that the fuel business is based on quality. (Author)

  15. Solid Freeform Fabrication Proceedings -1999

    Science.gov (United States)

    1999-08-11

    noded bilinear thermal elements are used as part of the ABAQUS finite element software package. The laser beam focused on the top surface of substrate...with the PDM technology. The advantage of SDM is that refractory metals can be melted with the plasma-welding torch. In 3-D Printing, a green part is...Freeform Growth. I. Introduction Previous efforts in vapor-phase solid freeform fabrication have concentrated on the growth of transition and refractory

  16. Nanocarbon materials fabricated using plasmas

    Science.gov (United States)

    Hatakeyama, Rikizo

    2017-12-01

    Since the discovery of fullerenes more than three decades ago, new kinds of nanoscale materials of carbon allotropes called "nanocarbons" have so far been discovered or synthesized at successive intervals as cases such as carbon nanotubes, carbon nanohorns, graphene, carbon nanowalls, and a carbon nanobelt, while nanodiamonds were actually discovered before then. Their attractively excellent mechanical, physical, and chemical properties have driven researchers to continuously create one of the hottest frontiers in materials science and technology. While plasma states have often been involved in their discovery, on the other hand, plasma-based approaches to this exciting field originally hold promising and enormous potentials for advancing and expanding industrial/biomedical applications of nanocarbons of great diversity. This article provides an extensive overview on plasma-fabricated nanocarbon materials, where the term "fabrication" is defined as synthesis, functionalization, and assembly of devices to cover a wide range of issues associated with the step-by-step plasma processes. Specific attention has been paid to the comparative examination between plasma-based and non-plasma methods for fabricating the nanocarobons with an emphasis on the advantages of plasma processing, such as low-temperature/large-scale fabrication and diversity-carrying structure controllability. The review ends with current challenges and prospects including a ripple effect of the nanocarbon studies on the development of related novel nanomaterials such as transition metal dichalcogenides. It contains not only the latest progress in the field for cutting-edge scientists and engineers, but also the introductory guidance to non-specialists such as lower-class graduate students.

  17. A simplified approach to fabrication of an ocular prosthesis: A case series

    Directory of Open Access Journals (Sweden)

    Kaur Amandeep

    2010-01-01

    Full Text Available The eye is a vital organ and an important component of facial expression. Loss of an eye has a crippling effect on the psychology of the patient. Enucleation of the eye is therefore normally followed by fabrication of an ocular prosthesis to improve esthetics. A less complex technique for fabrication of an ocular prosthesis is described in this report of two different cases.

  18. Fabrication technology for ODS Alloy MA957

    International Nuclear Information System (INIS)

    ML Hamilton; DS Gelles; RJ Lobsinger; MM Paxton; WF Brown

    2000-01-01

    A successful fabrication schedule has been developed at Carpenter Technology Corporation for the production of MA957 fuel and blanket cladding. Difficulties with gun drilling, plug drawing and recrystallization were overcome to produce a pilot lot of tubing. This report documents the fabrication efforts of two qualified vendors and the support studies performed at WHC to develop the fabrication-schedule

  19. Natural fabric sandwich laminate composites: development and ...

    Indian Academy of Sciences (India)

    Home; Journals; Bulletin of Materials Science; Volume 40; Issue 1 ... Natural fabrics; jute; linen; sandwich laminate; mechanical properties; fractographic analysis. ... In this work, eco-friendly natural fabric sandwich laminate (NFSL) composites are formulated using jute and linen-fabric-reinforced epoxy with different layer ...

  20. Method for fabricating semiconductor devices

    Science.gov (United States)

    Kaiser, William J. (Inventor); Grunthaner, Frank J. (Inventor); Hecht, Michael H. (Inventor); Bell, Lloyd D. (Inventor)

    1995-01-01

    A process for fabricating gold/gallium arsenide structures, in situ, on molecular beam epitaxially grown gallium arsenide. The resulting interface proves to be Ohmic, an unexpected result which is interpreted in terms of increased electrode interdiffusion. More importantly, the present invention surprisingly permits the fabrication of Ohmic contacts in a III-V semiconductor material at room temperature. Although it may be desireable to heat the Ohmic contact to a temperature of, for example, 200 degrees Centigrade if one wishes to further decrease the resistance of the contact, such low temperature annealing is much less likely to have any deleterious affect on the underlying substrate. The use of the term in situ herein, contemplates continuously maintaining an ultra-high vacuum, that is a vacuum which is at least 10.sup.-8 Torr, until after the metallization has been completed. An alternative embodiment of the present invention comprising an additional step, namely the termination of the gallium arsenide by a two monolayer thickness of epitaxial aluminum arsenide as a diffusion barrier, enables the recovery of Schottky barrier behavior, namely a rectified I-V characteristic. The present invention provides a significant breakthrough in the fabrication of III-V semiconductor devices wherein excellent Ohmic contact and Schottky barrier interfaces to such devices can be achieved simply and inexpensively and without requiring the high temperature processing of the prior art and also without requiring the use of exotic high temperature refractory materials as substitutes for those preferred contact metals such as gold, aluminum and the like.

  1. Phosphorene: Fabrication, Properties, and Applications.

    Science.gov (United States)

    Kou, Liangzhi; Chen, Changfeng; Smith, Sean C

    2015-07-16

    Phosphorene, the single- or few-layer form of black phosphorus, was recently rediscovered as a two-dimensional layered material holding great promise for applications in electronics and optoelectronics. Research into its fundamental properties and device applications has since seen exponential growth. In this Perspective, we review recent progress in phosphorene research, touching upon topics on fabrication, properties, and applications; we also discuss challenges and future research directions. We highlight the intrinsically anisotropic electronic, transport, optoelectronic, thermoelectric, and mechanical properties of phosphorene resulting from its puckered structure in contrast to those of graphene and transition-metal dichalcogenides. The facile fabrication and novel properties of phosphorene have inspired design and demonstration of new nanodevices; however, further progress hinges on resolutions to technical obstructions like surface degradation effects and nonscalable fabrication techniques. We also briefly describe the latest developments of more sophisticated design concepts and implementation schemes that address some of the challenges in phosphorene research. It is expected that this fascinating material will continue to offer tremendous opportunities for research and development for the foreseeable future.

  2. Micro Machining Enhances Precision Fabrication

    Science.gov (United States)

    2007-01-01

    Advanced thermal systems developed for the Space Station Freedom project are now in use on the International Space Station. These thermal systems employ evaporative ammonia as their coolant, and though they employ the same series of chemical reactions as terrestrial refrigerators, the space-bound coolers are significantly smaller. Two Small Business Innovation Research (SBIR) contracts between Creare Inc. of Hanover, NH and Johnson Space Center developed an ammonia evaporator for thermal management systems aboard Freedom. The principal investigator for Creare Inc., formed Mikros Technologies Inc. to commercialize the work. Mikros Technologies then developed an advanced form of micro-electrical discharge machining (micro-EDM) to make tiny holes in the ammonia evaporator. Mikros Technologies has had great success applying this method to the fabrication of micro-nozzle array systems for industrial ink jet printing systems. The company is currently the world leader in fabrication of stainless steel micro-nozzles for this market, and in 2001 the company was awarded two SBIR research contracts from Goddard Space Flight Center to advance micro-fabrication and high-performance thermal management technologies.

  3. Fabrication of Artificial Food Bolus for Evaluation of Swallowing.

    Directory of Open Access Journals (Sweden)

    Miyu Hosotsubo

    Full Text Available Simple and easy methods to evaluate swallowing are required because of the recently increased need of rehabilitation for dysphagia. "Artificial food bolus", but not "artificial food", would be a valuable tool for swallowing evaluation without considering the mastication effect which is altered according to the individual's oral condition. Thus, this study was carried out to fabricate artificial bolus resembling natural food bolus. The mechanical property and the volume change of food bolus in normal people were firstly investigated. Thirty healthy adults without dysphagia were selected and asked to chew four sample foods (rice cake, peanut, burdock, and gummy candy. The results indicated that Young's modulus of bolus before swallowing was below 150 kPa. The bolus volume before swallowing was below 400 mm3. In addition, the saliva component ratio of each bolus was approximately 30wt%, and the average saliva viscosity of research participants was approximately 10 mPa•s. Based on the obtained data, artificial food bolus was designed and fabricated by using alginate hydrogel as a visco-elastic material and gelatin solution as a viscotic material with a ratio of 7:3 based on weight. Consequently, the swallowing time of fabricated artificial food bolus was measured among the same participants. The results indicated the participants swallowed fabricated food bolus with similar manner reflecting their mechanical property and volume. Thus, this artificial food bolus would be a promising tool for evaluation of swallowing.

  4. Fabrication of biomimetic dry-adhesion structures through nanosphere lithography

    Science.gov (United States)

    Kuo, P. C.; Chang, N. W.; Suen, Y.; Yang, S. Y.

    2018-03-01

    Components with surface nanostructures suitable for biomimetic dry adhesion have a great potential in applications such as gecko tape, climbing robots, and skin patches. In this study, a nanosphere lithography technique with self-assembly nanospheres was developed to achieve effective and efficient fabrication of dry-adhesion structures. Self-assembled monolayer nanospheres with high regularity were obtained through tilted dip-coating. Reactive-ion etching of the self-assembled nanospheres was used to fabricate nanostructures of different shapes and aspect ratios by varying the etching time. Thereafter, nickel molds with inverse nanostructures were replicated using the electroforming process. Polydimethylsiloxane (PDMS) nanostructures were fabricated through a gas-assisted hot-embossing method. The pulling test was performed to measure the shear adhesion on the glass substrate of a sample, and the static contact angle was measured to verify the hydrophobic property of the structure. The enhancement of the structure indicates that the adhesion force increased from 1.2 to 4.05 N/cm2 and the contact angle increased from 118.6° to 135.2°. This columnar structure can effectively enhance the adhesion ability of PDMS, demonstrating the potential of using nanosphere lithography for the fabrication of adhesive structures.

  5. Facile fabrication of a superhydrophobic fabric with mechanical stability and easy-repairability.

    Science.gov (United States)

    Zhu, Xiaotao; Zhang, Zhaozhu; Yang, Jin; Xu, Xianghui; Men, Xuehu; Zhou, Xiaoyan

    2012-08-15

    The poor mechanical stability of superhydrophobic fabrics severely hindered their use in practical applications. Herein, to address this problem, we fabricated a superhydrophobic fabric with both mechanical stability and easy-repairability by a simple method. The mechanical durability of the obtained superhydrophobic fabric was evaluated by finger touching and abrasion with sandpaper. The results show that rough surface textures of the fabric were retained, and the fabric surface still exhibited superhydrophobicity after tests. More importantly, when the fabric lost its superhydrophobicity after a long-time abrasion, it can be easily rendered with superhydrophobicity once more by a regeneration process. Copyright © 2012 Elsevier Inc. All rights reserved.

  6. Innovative Application of Fabric Recycling in Fashion

    Directory of Open Access Journals (Sweden)

    Chenyang Lee

    2017-10-01

    Full Text Available With the continuous development of the socialist market economy, human aesthetic standards are constantly changing, the occurrence of this situation to the development of the garment industry challenges, that is a single fabric has long been unable to meet people's aesthetic needs, And then the art of fabric reengineering will be born. This paper elaborates the meaning of fabric reworking art. This paper systematically describes the meaning of fabric reengineering to garment designer and garment itself, and comprehensively summarizes the fabric recycling technique and its characteristics.

  7. Micro-fabricated all optical pressure sensors

    DEFF Research Database (Denmark)

    Havreland, Andreas Spandet; Petersen, Søren Dahl; Østergaard, Christian

    2017-01-01

    Optical pressure sensors can operate in certain harsh application areas where the electrical pressure sensors cannot. However, the sensitivity is often not as good for the optical sensors. This work presents an all optical pressure sensor, which is fabricated by micro fabrication techniques, where...... the sensitivity can be tuned in the fabrication process. The developed sensor design, simplifies the fabrication process leading to a lower fabrication cost, which can make the all optical pressure sensors more competitive towards their electrical counterpart. The sensor has shown promising results and a linear...

  8. Remote fabrication of nuclear fuel: a secure automated fabrication overview

    International Nuclear Information System (INIS)

    Nyman, D.H.; Benson, E.M.; Yatabe, J.M.; Nagamoto, T.T.

    1981-01-01

    An automated line for the fabrication of breeder reactor fuel pins is being developed. The line will be installed in the Fuels and Materials Examination Facility (FMEF) presently under construction at the Hanford site near Richland, Washington. The application of automation and remote operations to fuel processing technology is needed to meet program requirements of reduced personnel exposure, enhanced safeguards, improved product quality, and increased productivity. Commercially available robots are being integrated into operations such as handling of radioactive material within a process operation. These and other automated equipment and chemistry analyses systems under development are described

  9. Explosive Components Facility

    Data.gov (United States)

    Federal Laboratory Consortium — The 98,000 square foot Explosive Components Facility (ECF) is a state-of-the-art facility that provides a full-range of chemical, material, and performance analysis...

  10. Fabric-based active electrode design and fabrication for health monitoring clothing.

    Science.gov (United States)

    Merritt, Carey R; Nagle, H Troy; Grant, Edward

    2009-03-01

    In this paper, two versions of fabric-based active electrodes are presented to provide a wearable solution for ECG monitoring clothing. The first version of active electrode involved direct attachment of surface-mountable components to a textile screen-printed circuit using polymer thick film techniques. The second version involved attaching a much smaller, thinner, and less obtrusive interposer containing the active electrode circuitry to a simplified textile circuit. These designs explored techniques for electronic textile interconnection, chip attachment to textiles, and packaging of circuits on textiles for durability. The results from ECG tests indicate that the performance of each active electrode is comparable to commercial Ag/AgCl electrodes. The interposer-based active electrodes survived a five-cycle washing test while maintaining good signal integrity.

  11. Geomechanical Anisotropy and Rock Fabric in Shales

    Science.gov (United States)

    Huffman, K. A.; Connolly, P.; Thornton, D. A.

    2017-12-01

    Digital rock physics (DRP) is an emerging area of qualitative and quantitative scientific analysis that has been employed on a variety of rock types at various scales to characterize petrophysical, mechanical, and hydraulic rock properties. This contribution presents a generic geomechanically focused DRP workflow involving image segmentation by geomechanical constituents, generation of finite element (FE) meshes, and application of various boundary conditions (i.e. at the edge of the domain and at boundaries of various components such as edges of individual grains). The generic workflow enables use of constituent geological objects and relationships in a computational based approach to address specific questions in a variety of rock types at various scales. Two examples are 1) modeling stress dependent permeability, where it occurs and why it occurs at the grain scale; 2) simulating the path and complexity of primary fractures and matrix damage in materials with minerals or intervals of different mechanical behavior. Geomechanical properties and fabric characterization obtained from 100 micron shale SEM images using the generic DRP workflow are presented. Image segmentation and development of FE simulation composed of relatively simple components (elastic materials, frictional contacts) and boundary conditions enable the determination of bulk static elastic properties. The procedure is repeated for co-located images at pertinent orientations to determine mechanical anisotropy. The static moduli obtained are benchmarked against lab derived measurements since material properties (esp. frictional ones) are poorly constrained at the scale of investigation. Once confidence in the input material parameters is gained, the procedure can be used to characterize more samples (i.e. images) than is possible from rock samples alone. Integration of static elastic properties with grain statistics and geologic (facies) conceptual models derived from core and geophysical logs

  12. Space laser components reliability

    OpenAIRE

    Riede, Wolfgang; Schroeder, Helmut

    2015-01-01

    Space environment presents unique challenges for operation of optics and optical coatings as part of laser systems. Besides testing components and sub-systems on the component qualification level, the extended testing of complete laser systems like flight modules under acceptance level conditions is an effective way to determine the reliability and long term stability, mitigating the mission risk. Hence, optics as part of high power space laser systems have to be extensively tested in view...

  13. Component fragility research program

    International Nuclear Information System (INIS)

    Tsai, N.C.; Mochizuki, G.L.; Holman, G.S.

    1989-11-01

    To demonstrate how ''high-level'' qualification test data can be used to estimate the ultimate seismic capacity of nuclear power plant equipment, we assessed in detail various electrical components tested by the Pacific Gas ampersand Electric Company for its Diablo Canyon plant. As part of our Phase I Component Fragility Research Program, we evaluated seismic fragility for five Diablo Canyon components: medium-voltage (4kV) switchgear; safeguard relay board; emergency light battery pack; potential transformer; and station battery and racks. This report discusses our Phase II fragility evaluation of a single Westinghouse Type W motor control center column, a fan cooler motor controller, and three local starters at the Diablo Canyon nuclear power plant. These components were seismically qualified by means of biaxial random motion tests on a shaker table, and the test response spectra formed the basis for the estimate of the seismic capacity of the components. The seismic capacity of each component is referenced to the zero period acceleration (ZPA) and, in our Phase II study only, to the average spectral acceleration (ASA) of the motion at its base. For the motor control center, the seismic capacity was compared to the capacity of a Westinghouse Five-Star MCC subjected to actual fragility tests by LLNL during the Phase I Component Fragility Research Program, and to generic capacities developed by the Brookhaven National Laboratory for motor control center. Except for the medium-voltage switchgear, all of the components considered in both our Phase I and Phase II evaluations were qualified in their standard commercial configurations or with only relatively minor modifications such as top bracing of cabinets. 8 refs., 67 figs., 7 tabs

  14. Impact test of components

    International Nuclear Information System (INIS)

    Borsoi, L.; Buland, P.; Labbe, P.

    1987-01-01

    Stops with gaps are currently used to support components and piping: it is simple, low cost, efficient and permits free thermal expansion. In order to keep the nonlinear nature of stops, such design is often modeled by beam elements (for the component) and nonlinear springs (for the stops). This paper deals with the validity and the limits of these models through the comparison of computational and experimental results. The experimental results come from impact laboratory tests on a simplified mockup. (orig.)

  15. Properties of honeycomb polyester knitted fabrics

    Science.gov (United States)

    Feng, A. F.

    2016-07-01

    The properties of honeycomb polyester weft-knitted fabrics were studied to understand their advantages. Seven honeycomb polyester weft-knitted fabrics and one common polyester weft-knitted fabric were selected for testing. Their bursting strengths, fuzzing and pilling, air permeability, abrasion resistance and moisture absorption and perspiration were studied. The results show that the honeycomb polyester weft-knitted fabrics have excellent moisture absorption and liberation. The smaller their thicknesses and area densities are, the better their moisture absorption and liberation will be. Their anti-fuzzing and anti-pilling is good, whereas their bursting strengths and abrasion resistance are poorer compared with common polyester fabric's. In order to improve the hygroscopic properties of the fabrics, the proportion of the honeycomb microporous structure modified polyester in the fabrics should not be less than 40%.

  16. Design Thinking for Digital Fabrication in Education

    DEFF Research Database (Denmark)

    Smith, Rachel Charlotte; Iversen, Ole Sejer; Hjorth, Mikkel

    2015-01-01

    In this paper, we argue that digital fabrication in education may benefit from design thinking, to foster a more profound understanding of digital fabrication processes among students. Two related studies of digital fabrication in education are presented in the paper. In an observational study we...... found that students (eleven to fifteen) lacked an understanding of the complexity of the digital fabrication process impeding on the potentials of digital fabrication in education. In a second explorative research through design study, we investigated how a focus on design thinking affected the students......’ performance in digital fabrication processes. Our findings indicate that design thinking can provide students with a general understanding of the creative and complex process through which artifacts and futures emerge in processes of digital fabrication....

  17. Two-component injection moulding simulation of ABS-POM micro structured surfaces

    DEFF Research Database (Denmark)

    Tosello, Guido; Hansen, Hans Nørgaard; Islam, Aminul

    2013-01-01

    Multi-component micro injection moulding (μIM) processes such as two-component (2k) μIM are the key technologies for the mass fabrication of multi-material micro products. 2k-μIM experiments involving a miniaturized test component with micro features in the sub-mm dimensional range and moulding a...... process. Flow front predictions are compared with experimental results using the short shots technique over the whole miniaturized component and within the surface micro structures....

  18. FFTF metal fuel pin fabrication

    International Nuclear Information System (INIS)

    Dittmer, J.O.; Benecke, M.W.; Feigenbutz, L.V.

    1989-01-01

    A major new initiative to develop, irradiate, and qualify a binary uranium/zirconium metal-fuel system in the Fast Flux Test Facility (FFTF) has been implemented by the Westinghouse Hanford Company for the US Department of Energy. Metal-fuel test assemblies have been designed and fabricated, and are now being irradiated in FFTF to provide the data needed to support the potential use of binary metal fuels in FFTF and other liquid-metal reactors. These development efforts support licensing activities for metal-fuel use in near-term advanced liquid-metal reactors

  19. The Fabrication of Qualified Citizens

    DEFF Research Database (Denmark)

    Andrade-Molina, Melissa

    2017-01-01

    Within the practices of school mathematics there exists many naturalized truths that have been (re)produced in different times and in different places. The belief of mathematics education becoming the key to economical progress assuring the future growth of nations is problematized. By following...... a rhizomatic analytical move, a historization of the present is deployed to map the fabrication of the desired qualified citizen in Chile. The analysis evidences the (re)production of dominant narratives about the “qualified citizen” are and have been entangled with the functioning of school geometry...

  20. Corning lightweight core fabrication technologies

    Science.gov (United States)

    VanBrocklin, Randy R.; Edwards, Mary J.; Hobbs, Thomas W.

    2003-12-01

    Fabrication of lightweight mirrors from low expansion glasses can be achieved using various core and faceplate lightweighting techniques. Lightweighting can be achieved using abrasive waterjet cutting, CNC milling and a new approach that Corning is developing to produce lightweight cores based on Corning's patented ceramic extrusion process. The selection of which lightweighting technology to use is dependent on customer design considerations of the lightweight mirror. These lightweighting techniques are reviewed and discussed, along with advantages and disadvantages of each technique. Corning will also introduce and discuss their new core lightweighting process.

  1. Wafer-scale fabrication of polymer distributed feedback lasers

    DEFF Research Database (Denmark)

    Christiansen, Mads Brøkner; Schøler, Mikkel; Balslev, Søren

    2006-01-01

    The authors demonstrate wafer-scale, parallel process fabrication of distributed feedback (DFB) polymer dye lasers by two different nanoimprint techniques: By thermal nanoimprint lithography (TNIL) in polymethyl methacrylate and by combined nanoimprint and photolithography (CNP) in SU-8. In both...... techniques, a thin film of polymer, doped with rhodamine-6G laser dye, is spin coated onto a Borofloat glass buffer substrate and shaped into a planar waveguide slab with first order DFB surface corrugations forming the laser resonator. When optically pumped at 532 nm, lasing is obtained in the wavelength...... range between 576 and 607 nm, determined by the grating period. The results, where 13 laser devices are defined across a 10 cm diameter wafer substrate, demonstrate the feasibility of NIL and CNP for parallel wafer-scale fabrication of advanced nanostructured active optical polymer components...

  2. A Facile Way to Fabricate Transparent Superhydrophobic Surfaces.

    Science.gov (United States)

    Shi, Wentao; He, Ran; Yunus, Doruk E; Yang, Jie; Liu, Yaling

    2018-07-01

    A fast, easy, and low-cost way to fabricate transparent superhydrophobic (SHP) surfaces is developed. By simply mixing silica nanoparticles (SiNPs), polydimethylsiloxane (PDMS) and heptane to form a suspension, dip- or drop-coating the suspension onto different surfaces, transparent SHP surfaces can be obtained. By tuning the ratio of the three components above, transparency of the coating can reach more than 90% transmittance in the visible region, while static water contact angle of the coating can reach as high as 162°. Dynamic contact angle study shows the advancing contact angle and receding contact angle of water can be as high as 168° and 161°, and the resulting contact angle hysteresis can be as low as 7°. The reported facile way of fabricating transparent superhydrophobic (SHP) surfaces is potential for applications which need both optical transparency and self-cleaning capability, such as solar cells, optical equipment, and visible microfluidic chips.

  3. A solar module fabrication process for HALE solar electric UAVs

    Energy Technology Data Exchange (ETDEWEB)

    Carey, P.G.; Aceves, R.C.; Colella, N.J.; Williams, K.A. [Lawrence Livermore National Lab., CA (United States); Sinton, R.A. [Private Consultant, San Jose, CA (United States); Glenn, G.S. [Spectrolab, Inc., Sylmar, CA (United States)

    1994-12-12

    We describe a fabrication process used to manufacture high power-to-weight-ratio flexible solar array modules for use on high-altitude-long-endurance (HALE) solar-electric unmanned air vehicles (UAVs). These modules have achieved power-to-weight ratios of 315 and 396 W/kg for 150{mu}m-thick monofacial and 110{mu}m-thick bifacial silicon solar cells, respectively. These calculations reflect average module efficiencies of 15.3% (150{mu}m) and 14.7% (110{mu}m) obtained from electrical tests performed by Spectrolab, Inc. under AMO global conditions at 25{degrees}C, and include weight contributions from all module components (solar cells, lamination material, bypass diodes, interconnect wires, and adhesive tape used to attach the modules to the wing). The fabrication, testing, and performance of 32 m{sup 2} of these modules will be described.

  4. RFQ1 fabrication and low power RF tuning

    International Nuclear Information System (INIS)

    McMichael, G.E.; Chidley, B.G.; Hutcheon, R.M.; TranNgoc, T.

    1987-01-01

    RFQ1, a 600 keV, 75 mA proton RFQ is the major component of a research program at the Chalk River Nuclear Laboratories (CRNL) to study high current 100% duty factor accelerator systems and develop improved accelerator technology. Features of the 270 MHz RFQ include removable vanes, vane coupling rings, and loop coupling to the rf drive line with the option of two drive loops. The main RFQ tank and vane bodies are fabricated from carbon steel which is copper plated following machining of the OFHC copper vane tips and initial low power rf tuning. Details of the mechanical fabrication and low power tuning are presented and rf characteristics compared with computer code predictions

  5. Design, fabrication and operation of the LVDT based vertical dilatometer

    International Nuclear Information System (INIS)

    Manoj, N.; Kerkar, A.S.; Mathews, M.D.; Gautam, J.K.; Tyagi, A.K.; Thomas, K.C.

    2005-07-01

    This report provides the details of a dilatometer developed in-house to measure thermal expansion from room temperature to 1173 K. The instrument was designed, fabricated and tested for its satisfactory performance by analyzing the thermal expansion properties of several materials up to a maximum temperature of 1123 K. One of the important feature in this design is that, the instrument has been fabricated by using all indigenously available components. The sample loading and initial zero adjustment procedure has been made very simple in this design. The software for furnace temperature programming and control, data collection, data processing and plotting of the graph has also been developed. Provision for carrying out the measurements in vacuum as well as flowing gas have been provided. (author)

  6. Design, fabrication, and characterization of high-efficiency extreme ultraviolet diffusers

    Energy Technology Data Exchange (ETDEWEB)

    Naulleau, Patrick P.; Liddle, J. Alexander; Salmassi, Farhad; Anderson, Erik H.; Gullikson, Eric M.

    2004-02-19

    As the development of extreme ultraviolet (EUV) lithography progresses, interest grows in the extension of traditional optical components to the EUV regime. The strong absorption of EUV by most materials and its extremely short wavelength, however, makes it very difficult to implement many components that are commonplace in the longer wavelength regimes. One such example is the diffuser often implemented with ordinary ground glass in the visible light regime. Here we demonstrate the fabrication of reflective EUV diffusers with high efficiency within a controllable bandwidth. Using these techniques we have fabricated diffusers with efficiencies exceeding 10% within a moderate angular single-sided bandwidth of approximately 0.06 radians.

  7. Encyclopedia of Software Components

    Science.gov (United States)

    Warren, Lloyd V. (Inventor); Beckman, Brian C. (Inventor)

    1997-01-01

    Intelligent browsing through a collection of reusable software components is facilitated with a computer having a video monitor and a user input interface such as a keyboard or a mouse for transmitting user selections, by presenting a picture of encyclopedia volumes with respective visible labels referring to types of software, in accordance with a metaphor in which each volume includes a page having a list of general topics under the software type of the volume and pages having lists of software components for each one of the generic topics, altering the picture to open one of the volumes in response to an initial user selection specifying the one volume to display on the monitor a picture of the page thereof having the list of general topics and altering the picture to display the page thereof having a list of software components under one of the general topics in response to a next user selection specifying the one general topic, and then presenting a picture of a set of different informative plates depicting different types of information about one of the software components in response to a further user selection specifying the one component.

  8. Multiscale principal component analysis

    International Nuclear Information System (INIS)

    Akinduko, A A; Gorban, A N

    2014-01-01

    Principal component analysis (PCA) is an important tool in exploring data. The conventional approach to PCA leads to a solution which favours the structures with large variances. This is sensitive to outliers and could obfuscate interesting underlying structures. One of the equivalent definitions of PCA is that it seeks the subspaces that maximize the sum of squared pairwise distances between data projections. This definition opens up more flexibility in the analysis of principal components which is useful in enhancing PCA. In this paper we introduce scales into PCA by maximizing only the sum of pairwise distances between projections for pairs of datapoints with distances within a chosen interval of values [l,u]. The resulting principal component decompositions in Multiscale PCA depend on point (l,u) on the plane and for each point we define projectors onto principal components. Cluster analysis of these projectors reveals the structures in the data at various scales. Each structure is described by the eigenvectors at the medoid point of the cluster which represent the structure. We also use the distortion of projections as a criterion for choosing an appropriate scale especially for data with outliers. This method was tested on both artificial distribution of data and real data. For data with multiscale structures, the method was able to reveal the different structures of the data and also to reduce the effect of outliers in the principal component analysis

  9. Fabricating with crystalline Si to improve superconducting detector performance

    Science.gov (United States)

    Beyer, A. D.; Hollister, M. I.; Sayers, J.; Frez, C. F.; Day, P. K.; Golwala, S. R.

    2017-05-01

    We built and measured radio-frequency (RF) loss tangent, tan δ, evaluation structures using float-zone quality silicon-on-insulator (SOI) wafers with 5 μm thick device layers. Superconducting Nb components were fabricated on both sides of the SOI Si device layer. Our main goals were to develop a robust fabrication for using crystalline Si (c-Si) dielectric layers with superconducting Nb components in a wafer bonding process and to confirm that tan δ with c-Si dielectric layers was reduced at RF frequencies compared to devices fabricated with amorphous dielectrics, such as SiO2 and SixNy, where tan δ ∼ 10-3. Our primary test structure used a Nb coplanar waveguide (CPW) readout structure capacitively coupled to LC resonators, where the capacitors were defined as parallel-plate capacitors on both sides of a c-Si device layer using a wafer bonding process with benzocyclobutene (BCB) wafer bonding adhesive. Our control experiment, to determine the intrinsic tan δ in the SOI device layer without wafer bonding, also used Nb CPW readout coupled to LC resonators; however, the parallel-plate capacitors were fabricated on both sides of the Si device layer using a deep reactive ion etch (DRIE) to access the c-Si underside through the buried oxide and handle Si layers in the SOI wafers. We found that our wafer bonded devices demonstrated F· δ = (8 ± 2) × 10-5, where F is the filling fraction of two-level states (TLS). For the control experiment, F· δ = (2.0 ± 0.6) × 10-5, and we discuss what may be degrading the performance in the wafer bonded devices as compared to the control devices.

  10. Fabricating with crystalline Si to improve superconducting detector performance

    International Nuclear Information System (INIS)

    Beyer, A D; Frez, C F; Day, P K; Hollister, M I; Sayers, J; Golwala, S R

    2017-01-01

    We built and measured radio-frequency (RF) loss tangent, tan δ, evaluation structures using float-zone quality silicon-on-insulator (SOI) wafers with 5 μm thick device layers. Superconducting Nb components were fabricated on both sides of the SOI Si device layer. Our main goals were to develop a robust fabrication for using crystalline Si (c-Si) dielectric layers with superconducting Nb components in a wafer bonding process and to confirm that tan δ with c-Si dielectric layers was reduced at RF frequencies compared to devices fabricated with amorphous dielectrics, such as SiO_2 and Si_xN_y, where tan δ ∼ 10"-"3. Our primary test structure used a Nb coplanar waveguide (CPW) readout structure capacitively coupled to LC resonators, where the capacitors were defined as parallel-plate capacitors on both sides of a c-Si device layer using a wafer bonding process with benzocyclobutene (BCB) wafer bonding adhesive. Our control experiment, to determine the intrinsic tan δ in the SOI device layer without wafer bonding, also used Nb CPW readout coupled to LC resonators; however, the parallel-plate capacitors were fabricated on both sides of the Si device layer using a deep reactive ion etch (DRIE) to access the c-Si underside through the buried oxide and handle Si layers in the SOI wafers. We found that our wafer bonded devices demonstrated F· δ = (8 ± 2) × 10"-"5, where F is the filling fraction of two-level states (TLS). For the control experiment, F· δ = (2.0 ± 0.6) × 10"-"5, and we discuss what may be degrading the performance in the wafer bonded devices as compared to the control devices. (paper)

  11. Porosity Prediction of Plain Weft Knitted Fabrics

    Directory of Open Access Journals (Sweden)

    Muhammad Owais Raza Siddiqui

    2014-12-01

    Full Text Available Wearing comfort of clothing is dependent on air permeability, moisture absorbency and wicking properties of fabric, which are related to the porosity of fabric. In this work, a plug-in is developed using Python script and incorporated in Abaqus/CAE for the prediction of porosity of plain weft knitted fabrics. The Plug-in is able to automatically generate 3D solid and multifilament weft knitted fabric models and accurately determine the porosity of fabrics in two steps. In this work, plain weft knitted fabrics made of monofilament, multifilament and spun yarn made of staple fibers were used to evaluate the effectiveness of the developed plug-in. In the case of staple fiber yarn, intra yarn porosity was considered in the calculation of porosity. The first step is to develop a 3D geometrical model of plain weft knitted fabric and the second step is to calculate the porosity of the fabric by using the geometrical parameter of 3D weft knitted fabric model generated in step one. The predicted porosity of plain weft knitted fabric is extracted in the second step and is displayed in the message area. The predicted results obtained from the plug-in have been compared with the experimental results obtained from previously developed models; they agreed well.

  12. Versatile superamphiphobic cotton fabrics fabricated by coating with SiO2/FOTS

    Science.gov (United States)

    Li, Deke; Guo, Zhiguang

    2017-12-01

    A multifunctional superamphiphobic cotton fabric was fabricated by coating silica nanoparticles on the cotton fabric surface and further modification by 1H,1H,2H,2H-perfluorooctyltrichlorosilane (FOTS). The fluctuant woven fabric and the fluffy spherical SiO2 nanoparticles constructed a dual micro/nano-structures. The surface free energy of the fabric composite was reduced by FOTS modifier. The interplay of the structured and perfluorinated SiO2 nanoparticles could not only endow the fabric highly liquid repellent ability, but could also to enhance the coating stability. The prepared cotton fabrics exhibited high liquid repellency to water, colza oil and n-hexadecane with lower surface tension, showing a contact angle of 158°, 152°, and 153°, respectively. The results demonstrated that superamphiphobic cotton fabric possessed desirable chemical and mechanical durability, self-cleaning and self-healing property, the robust and multifunctional fabric would find innovative opportunities for practical applications.

  13. Optimization of Ultrasonic Fabric Cleaning

    Energy Technology Data Exchange (ETDEWEB)

    Hand, T.E.

    1998-05-13

    The fundamental purpose of this project was to research and develop a process that would reduce the cost and improve the environmental efficiency of the present dry-cleaning industry. This second phase of research (see report KCP-94-1006 for information gathered during the first phase) was intended to allow the optimal integration of all factors of ultrasonic fabric cleaning. For this phase, Garment Care performed an extensive literature search and gathered data from other researchers worldwide. The Garment Care-AlliedSignal team developed the requirements for a prototype cleaning tank for studies and acquired that tank and the additional equipment required to use it properly. Garment Care and AlliedSignal acquired the transducers and generators from Surftran Martin-Walter in Sterling Heights, Michigan. Amway's Kelly Haley developed the test protocol, supplied hundreds of test swatches, gathered the data on the swatches before and after the tests, assisted with the cleaning tests, and prepared the final analysis of the results. AlliedSignal personnel, in conjunction with Amway and Garment Care staff, performed all the tests. Additional planning is under way for future testing by outside research facilities. The final results indicated repeatable performance and good results for single layered fabric swatches. Swatches that were cleaned as a ''sandwich,'' that is, three or more layers.

  14. Polymer micromold and fabrication process

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Abraham P. (1428 Whitecliff Way, Walnut Creek, CA 94596); Northrup, M. Allen (923 Creston Rd., Berkeley, CA 94708); Ahre, Paul E. (1299 Gonzaga Ct., Livermore, CA 94550); Dupuy, Peter C. (1736 Waldo Ct., Modesto, CA 95358)

    1997-01-01

    A mold assembly with micro-sized features in which the hollow portion thereof is fabricated from a sacrificial mandrel which is surface treated and then coated to form an outer shell. The sacrificial mandrel is then selectively etched away leaving the outer shell as the final product. The sacrificial mandrel is fabricated by a precision lathe, for example, so that when removed by etching the inner or hollow area has diameters as small as 10's of micros (.mu.m). Varying the inside diameter contours of the mold can be accomplished with specified ramping slopes formed on the outer surface of the sacrificial mandrel, with the inside or hollow section being, for example, 275 .mu.m in length up to 150 .mu.m in diameter within a 6 mm outside diameter (o.d.) mold assembly. The mold assembly itself can serve as a micronozzle or microneedle, and plastic parts, such as microballoons for angioplasty, polymer microparts, and microactuators, etc., may be formed within the mold assembly.

  15. Polymer micromold and fabrication process

    Energy Technology Data Exchange (ETDEWEB)

    Lee, A.P.; Northrup, M.A.; Ahre, P.E.; Dupuy, P.C.

    1997-08-19

    A mold assembly is disclosed with micro-sized features in which the hollow portion thereof is fabricated from a sacrificial mandrel which is surface treated and then coated to form an outer shell. The sacrificial mandrel is then selectively etched away leaving the outer shell as the final product. The sacrificial mandrel is fabricated by a precision lathe, for example, so that when removed by etching the inner or hollow area has diameters as small as 10`s of micros ({micro}m). Varying the inside diameter contours of the mold can be accomplished with specified ramping slopes formed on the outer surface of the sacrificial mandrel, with the inside or hollow section being, for example, 275 {micro}m in length up to 150 {micro}m in diameter within a 6 mm outside diameter (o.d.) mold assembly. The mold assembly itself can serve as a micronozzle or microneedle, and plastic parts, such as microballoons for angioplasty, polymer microparts, and microactuators, etc., may be formed within the mold assembly. 6 figs.

  16. LEU fuel fabrication in Argentina

    International Nuclear Information System (INIS)

    Giorsetti, D.R.; Gomez, J.O.; Marajofsky, A.; Kohut, C.

    1985-01-01

    As an Institution, aiming to meet with its own needs, CNEA has been intensively developing reduced enriched fuel to use in its own research and test reactors. Development of the fabrication technology as well as the design, installation and operation of the manufacturing plant, have been carried out with its own funds. Irradiation and post-irradiation of test miniplates have been taking place within the framework of the RERTR program. During the last years, CNEA has developed three LEU fuel types. In the previous RERTR meetings, we presented the technological results obtained with these fuel types. This paper focuses on CNEA LEU fuel element manufacturing status and the trained personnel we can offer in design and manufacture fuel capability. CNEA has its own fuel manufacturing technology; the necessary facilities to start the fuel fabrication; qualified technicians and professionals for: fuel design and behaviour analysis; fuel manufacturing and QA; international recognition of its fuel development and manufacturing capability through its ORR miniplate irradiation; its own natural uranium and the future possibility to enrich up to 20% U 235 ; the probability to offer a competitive fuel manufacturing cost in the international market; the disposition to cooperate with all countries that wish to take part and aim to reach an self-sufficiency in their own fuel supply needs

  17. QUIJOTE telescope design and fabrication

    Science.gov (United States)

    Gomez, Alberto; Murga, Gaizka; Etxeita, Borja; Sanquirce, Rubén; Rebolo, Rafael; Rubiño-Martin, Jose Alberto; Herreros, José-Miguel; Hoyland, Roger; Gomez, Francisca; Génova-Santos, Ricardo T.; Piccirillo, Lucio; Maffei, Bruno; Watson, Robert

    2010-07-01

    The QUIJOTE CMB experiment aims to characterize the polarization of the CMB in the frequency range 10-30 GHz and large angular scales. It will be installed in the Teide Observatory, following the projects that the Anisotropy of the Cosmic Microwave Background group has developed in the past (Tenerife experiment, IAC-Bartol experiment...) and is running at the present time (VSA, Cosmosomas). The QUIJOTE CMB experiment will consist of two telescopes which will be installed inside a unique enclosure, which is already constructed. The layout of both telescopes is based on an altazimuth mount supporting a primary and a secondary mirror disposed in a offset Gregorian Dragon scheme. The use of industrial-like fabrication techniques, such as sand-mould casting, CNC machining, and laser tracker measuring for alignment, provided the required performances for microwave observation. A fast-track construction scheme, altogether with the use of these fabrication techniques allowed designing and manufacturing the opto-mechanics of the telescope in 14 months prior to delivery for final start-up in December 2008.

  18. Cognitive Component Analysis

    DEFF Research Database (Denmark)

    Feng, Ling

    2008-01-01

    of audio contexts along with pattern recognition methods to map components to known contexts. It also involves looking for the right representations for auditory inputs, i.e. the data analytic processing pipelines invoked by human brains. The main ideas refer to Cognitive Component Analysis, defined......This dissertation concerns the investigation of the consistency of statistical regularities in a signaling ecology and human cognition, while inferring appropriate actions for a speech-based perceptual task. It is based on unsupervised Independent Component Analysis providing a rich spectrum...... as the process of unsupervised grouping of generic data such that the ensuing group structure is well-aligned with that resulting from human cognitive activity. Its hypothesis runs ecologically: features which are essentially independent in a context defined ensemble, can be efficiently coded as sparse...

  19. Solid state lighting component

    Energy Technology Data Exchange (ETDEWEB)

    Yuan, Thomas; Keller, Bernd; Tarsa, Eric; Ibbetson, James; Morgan, Frederick; Dowling, Kevin; Lys, Ihor

    2017-10-17

    An LED component according to the present invention comprising an array of LED chips mounted on a submount with the LED chips capable of emitting light in response to an electrical signal. The array can comprise LED chips emitting at two colors of light wherein the LED component emits light comprising the combination of the two colors of light. A single lens is included over the array of LED chips. The LED chip array can emit light of greater than 800 lumens with a drive current of less than 150 milli-Amps. The LED chip component can also operate at temperatures less than 3000 degrees K. In one embodiment, the LED array is in a substantially circular pattern on the submount.

  20. Fabrication for precision mechanisms. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Gillespie, L.K.

    1980-03-01

    The fabrication of components and assemblies for miniature precision mechanisms provides a variety of exacting manufacturing challenges. Size alone makes many parts hard to pick up, handle, measure, and install. This same small size causes more distortion or bending during machining, assembly, and welding. Some parts even float on the cleaning and deburring solutions. Tools break easily in very small holes, and surface finishes play an important role in part operation. Twenty-five manufacturing operations were studied to improve the precision of existing machining and assembly techniques. The study included the machining of metals and plastics using techniques new to the manufacture of miniature switches, timers, and actuators. Drilling, tapping, and press-fitting miniature features were evaluated. Fixturing and handling techniques, friction reduction, and the forming of ceramic parts were also studied. Many of the new approaches from this study have been incorporated into existing processes and further refined. Detailed observations have been reported in 33 other Bendix reports and the highlights of those observations are summarized in this study.

  1. Fabricating Superhydrophobic Polymeric Materials for Biomedical Applications.

    Science.gov (United States)

    Kaplan, Jonah; Grinstaff, Mark

    2015-08-28

    Superhydrophobic materials, with surfaces possessing permanent or metastable non-wetted states, are of interest for a number of biomedical and industrial applications. Here we describe how electrospinning or electrospraying a polymer mixture containing a biodegradable, biocompatible aliphatic polyester (e.g., polycaprolactone and poly(lactide-co-glycolide)), as the major component, doped with a hydrophobic copolymer composed of the polyester and a stearate-modified poly(glycerol carbonate) affords a superhydrophobic biomaterial. The fabrication techniques of electrospinning or electrospraying provide the enhanced surface roughness and porosity on and within the fibers or the particles, respectively. The use of a low surface energy copolymer dopant that blends with the polyester and can be stably electrospun or electrosprayed affords these superhydrophobic materials. Important parameters such as fiber size, copolymer dopant composition and/or concentration, and their effects on wettability are discussed. This combination of polymer chemistry and process engineering affords a versatile approach to develop application-specific materials using scalable techniques, which are likely generalizable to a wider class of polymers for a variety of applications.

  2. Electrospinning: a fascinating fiber fabrication technique.

    Science.gov (United States)

    Bhardwaj, Nandana; Kundu, Subhas C

    2010-01-01

    With the emergence of nanotechnology, researchers become more interested in studying the unique properties of nanoscale materials. Electrospinning, an electrostatic fiber fabrication technique has evinced more interest and attention in recent years due to its versatility and potential for applications in diverse fields. The notable applications include in tissue engineering, biosensors, filtration, wound dressings, drug delivery, and enzyme immobilization. The nanoscale fibers are generated by the application of strong electric field on polymer solution or melt. The non-wovens nanofibrous mats produced by this technique mimics extracellular matrix components much closely as compared to the conventional techniques. The sub-micron range spun fibers produced by this process, offer various advantages like high surface area to volume ratio, tunable porosity and the ability to manipulate nanofiber composition in order to get desired properties and function. Over the years, more than 200 polymers have been electrospun for various applications and the number is still increasing gradually with time. With these in perspectives, we aim to present in this review, an overview of the electrospinning technique with its promising advantages and potential applications. We have discussed the electrospinning theory, spinnable polymers, parameters (solution and processing), which significantly affect the fiber morphology, solvent properties and melt electrospinning (alternative to solution electrospinning). Finally, we have focused on varied applications of electrospun fibers in different fields and concluded with the future prospects of this efficient technology. (c) 2010 Elsevier Inc. All rights reserved.

  3. Component Reengineering Workshops

    DEFF Research Database (Denmark)

    Hansen, Klaus Marius; Christensen, Henrik Bærbak

    2004-01-01

    In mature domains, a number of competing product lines may emerge, and from the point of view of customers of such product lines, reengineering and reuse of assets across product lines from different vendors becomes important. To address this issue we present a low-cost approach, component...... reengineering workshops, for assessing reengineering costs of reusing components between different product lines. The approach works on the level of software architectures, and relies critically on input from various (technical) stakeholders. It has been validated through case studies that are also presented...

  4. Fabrication of Flexible Piezoelectric PZT/Fabric Composite

    Directory of Open Access Journals (Sweden)

    Caifeng Chen

    2013-01-01

    Full Text Available Flexible piezoelectric PZT/fabric composite material is pliable and tough in nature which is in a lack of traditional PZT patches. It has great application prospect in improving the sensitivity of sensor/actuator made by piezoelectric materials especially when they are used for curved surfaces or complicated conditions. In this paper, glass fiber cloth was adopted as carrier to grow PZT piezoelectric crystal particles by hydrothermal method, and the optimum conditions were studied. The results showed that the soft glass fiber cloth was an ideal kind of carrier. A large number of cubic-shaped PZT nanocrystallines grew firmly in the carrier with a dense and uniform distribution. The best hydrothermal condition was found to be pH 13, reaction time 24 h, and reaction temperature 200°C.

  5. Fabrication of superhydrophobic cotton fabrics by silica hydrosol and hydrophobization

    Science.gov (United States)

    Xu, Lihui; Zhuang, Wei; Xu, Bi; Cai, Zaisheng

    2011-04-01

    Superhydrophobic cotton fabrics were prepared by the incorporation of silica nanoparticles and subsequent hydrophobization with hexadecyltrimethoxysilane (HDTMS). The silica nanoparticles were synthesized via sol-gel reaction with methyl trimethoxy silane (MTMS) as the precursor in the presence of the base catalyst and surfactant in aqueous solution. As for the resulting products, characterization by particle size analyzer, scanning electron microscopy (SEM), scanning probe microscopy (SPM), X-ray photoelectron spectroscopy (XPS), and thermal gravimetric analysis (TGA) were performed respectively. The size of SiO2 nanoparticles can be controlled by adjusting the catalyst and surfactant concentrations. The wettability of cotton textiles was evaluated by the water contact angle (WCA) and water shedding angle (WSA) measurements. The results showed that the treated cotton sample displayed remarkable water repellency with a WCA of 151.9° for a 5 μL water droplet and a WSA of 13° for a 15 μL water droplet.

  6. Fabrication of prototype mockups of ITER shielding blanket with separable first wall

    International Nuclear Information System (INIS)

    Kosaku, Yasuo; Kuroda, Toshimasa; Enoeda, Mikio; Hatano, Toshihisa; Sato, Satoshi; Akiba, Masato

    2002-07-01

    Design of shielding blanket for ITER-FEAT applies the first wall which has the separable structure from the shield block for the purpose of radio-active waste reduction in the maintenance work and cost reduction in fabrication process. Also, it is required to have various types of slots in both of the first wall and the shield block, to reduce the eddy current for reduction of electro-magnetic force in disruption events. This report summarizes the demonstrative fabrication of the ITER shielding blanket with separable first wall performed for the shielding blanket fabrication technology development, under the task agreement of G 16 TT 108 FJ (T420-2) in ITER Engineering Design Activity Extension Period. The objectives of the demonstrative fabrication are: to demonstrate the comprehensive fabrication technique in a large scale component (e.g the joining techniques for the beryllium armor/copper alloy and copper alloy/SS, and the slotting method of the FW and shield block); to develop an improved fabrication method for the shielding blanket based on the ITER-FEAT updated design. In this work, the fabrication technique of full scale separable first wall shield blanket was confirmed by fabricating full width Be armored first wall panel, full scale of 1/2 shield block with poloidal cooling channels. As the R and D for updated cooling channel configuration, the fabrication technique of the radial channel shield block was also demonstrated. Concluding to the all R and D results, it was demonstrated successfully that the fabrication technique and optimized conditions in the results obtained under the task agreement of G 16 TT 95 FJ (T420-1) was applicable to the prototype of the separable first wall blanket module. Additionally, basic echo data of ultra-sonic test method (UT) was obtained to show the applicability of UT method for in tube access detection of defect on the Cu alloy/SS tube interface. (author)

  7. Spain's nuclear components industry

    International Nuclear Information System (INIS)

    Kaibel, E.

    1985-01-01

    Spanish industrial participation in supply of components for nuclear power plants has grown steadily over the last fifteen years. The share of Spanish companies in work for the five second generation nuclear power plants increased to 50% of total capital investments. The necessity to maintain Spanish technology and production in the nuclear field is emphasized

  8. Component-oriented programming

    NARCIS (Netherlands)

    Bosch, J; Szyperski, C; Weck, W; Buschmann, F; Buchmann, AP; Cilia, MA

    2003-01-01

    This report covers the eighth Workshop on Component-Oriented Programming (WCOP). WCOP has been affiliated with ECOOP since its inception in 1996. The report summarizes the contributions made by authors of accepted position papers as well as those made by all attendees of the workshop sessions.

  9. Grey component analysis

    NARCIS (Netherlands)

    Westerhuis, J.A.; Derks, E.P.P.A.; Hoefsloot, H.C.J.; Smilde, A.K.

    2007-01-01

    The interpretation of principal component analysis (PCA) models of complex biological or chemical data can be cumbersome because in PCA the decomposition is performed without any knowledge of the system at hand. Prior information of the system is not used to improve the interpretation. In this paper

  10. Molecular Models Candy Components

    Science.gov (United States)

    Coleman, William F.

    2007-01-01

    An explanation of various principles of chemistry in a paper by Fanny Ennever by the use of candy is described. The paper explains components of sucrose and the invert sugar that results from the hydrolysis of sucrose and will help students in determining whether the products are indeed hydrates of carbon.

  11. Component lifetime modelling

    NARCIS (Netherlands)

    Verweij, J.F.; Verweij, J.F.; Brombacher, A.C.; Brombacher, A.C.; Lunenborg, M.M.; Lunenborg, M.M.

    1994-01-01

    There are two approaches to component lifetime modelling. The first one uses a reliability prediction method as described in the (military) handbooks with the appropriate models and parameters. The advantages are: (a) It takes into account all possible failure mechanisms. (b) It is easy to use. The

  12. Euler principal component analysis

    NARCIS (Netherlands)

    Liwicki, Stephan; Tzimiropoulos, Georgios; Zafeiriou, Stefanos; Pantic, Maja

    Principal Component Analysis (PCA) is perhaps the most prominent learning tool for dimensionality reduction in pattern recognition and computer vision. However, the ℓ 2-norm employed by standard PCA is not robust to outliers. In this paper, we propose a kernel PCA method for fast and robust PCA,

  13. Validating Timed Component Contracts

    DEFF Research Database (Denmark)

    Le Guilly, Thibaut; Liu, Shaoying; Olsen, Petur

    2015-01-01

    This paper presents a technique for testing software components with contracts that specify functional behavior, synchronization, as well as timing behavior. The approach combines elements from unit testing with model-based testing techniques for timed automata. The technique is implemented...... in an online testing tool, and we demonstrate its use on a concrete use case....

  14. ITER plasma facing components

    International Nuclear Information System (INIS)

    Kuroda, T.; Vieider, G.; Akiba, M.

    1991-01-01

    This document summarizes results of the Conceptual Design Activities (1988-1990) for the International Thermonuclear Experimental Reactor (ITER) project, namely those that pertain to the plasma facing components of the reactor vessel, of which the main components are the first wall and the divertor plates. After an introduction and an executive summary, the principal functions of the plasma-facing components are delineated, i.e., (i) define the low-impurity region within which the plasma is produced, (ii) absorb the electromagnetic radiation and charged-particle flux from the plasma, and (iii) protect the blanket/shield components from the plasma. A list of critical design issues for the divertor plates and the first wall is given, followed by discussions of the divertor plate design (including the issues of material selection, erosion lifetime, design concepts, thermal and mechanical analysis, operating limits and overall lifetime, tritium inventory, baking and conditioning, safety analysis, manufacture and testing, and advanced divertor concepts) and the first wall design (armor material and design, erosion lifetime, overall design concepts, thermal and mechanical analysis, lifetime and operating limits, tritium inventory, baking and conditioning, safety analysis, manufacture and testing, an alternative first wall design, and the limiters used instead of the divertor plates during start-up). Refs, figs and tabs

  15. Update On Monolithic Fuel Fabrication Development

    Energy Technology Data Exchange (ETDEWEB)

    C. R Clark; J. M. Wight; G. C. Knighton; G. A. Moore; J. F. Jue

    2005-11-01

    Efforts to develop a viable monolithic research reactor fuel plate have continued at Idaho National Laboratory. These efforts have concentrated on both fabrication process refinement and scale-up to produce full sized fuel plates. Advancements have been made in the production of U-Mo foil including full sized foils. Progress has also been made in the friction stir welding and transient liquid phase bonding fabrication processes resulting in better bonding, more stable processes and the ability to fabricate larger fuel plates.

  16. Plasmonic nanoparticles: Towards the fabrication of biosensors

    Science.gov (United States)

    Shen, Hui

    2015-07-01

    Au and Ag nanoparticles are mainly employed in the fabrication of biosensors owing to their unique optical properties compared to other noble metal nanoparticles. Many biosensors are fabricated for the rapid detection of different analytes such as organic and inorganic molecules, biomolecules like DNA, proteins, biotoxins and pathogens. In this mini review we mainly discuss on the usage of Au and Ag nanoparticles for the fabrication of colorimetric, SERS and two photon based photoluminescence biosensors.

  17. Nanocrystal thin film fabrication methods and apparatus

    Energy Technology Data Exchange (ETDEWEB)

    Kagan, Cherie R.; Kim, David K.; Choi, Ji-Hyuk; Lai, Yuming

    2018-01-09

    Nanocrystal thin film devices and methods for fabricating nanocrystal thin film devices are disclosed. The nanocrystal thin films are diffused with a dopant such as Indium, Potassium, Tin, etc. to reduce surface states. The thin film devices may be exposed to air during a portion of the fabrication. This enables fabrication of nanocrystal-based devices using a wider range of techniques such as photolithography and photolithographic patterning in an air environment.

  18. Plutonium fuel fabrication residues and wastes

    International Nuclear Information System (INIS)

    Arnal, T.; Cousinou, G.; Desille, H.

    1982-04-01

    This paper discusses the current situation in the fabrication plant at Cadarache with an annual plutonium throughput of several tons. Three major fabrication byproduct categories are defined in this plant: 1) scraps, directly recycled at the fabrication input station; 2) residues, byproducts recycled by chemical processes, or processed in washing and incineration stations; 3) wastes, placed in drums and evacuated directly to a waste conditioning station. The borderline between residues and wastes has yet to be precisely determined

  19. FABRIC TENSOR FOR DISCONTINUOUS GEOLOGICAL MATERIALS

    OpenAIRE

    小田, 匡寛

    1982-01-01

    Geometrical property (fabric) of discontinuity in geological materials is discussed in terms of (1) position and density, (2) shape and dimension and (3) orientation of related discontinuities such as joint, fault and discrete particle. By taking into account these geometrical elements, a unique measure called fabric tensor F_ is definitely introduced to embody the fabric concept without loss of generality.The first invariant of F_ is important as an index measure to evaluate the crack intens...

  20. Hemp nanocellulose: fabrication, characterisation and application

    OpenAIRE

    Dasong, Dai

    2015-01-01

    This thesis was submitted for the award of Doctor of Philosophy and was awarded by Brunel University London Nanocellulose has gained lots of attentions in recent years due to the development of nanotechnology. Thousands of publications have been reported about the fabrication, characterization and application of nanocellulose, among which most of the nanocelluloses were fabricated from the microcrystalline cellulose (MCC) or pulp, and only two methods about the nanocellulose fabrication ha...

  1. Developing a Model Component

    Science.gov (United States)

    Fields, Christina M.

    2013-01-01

    The Spaceport Command and Control System (SCCS) Simulation Computer Software Configuration Item (CSCI) is responsible for providing simulations to support test and verification of SCCS hardware and software. The Universal Coolant Transporter System (UCTS) was a Space Shuttle Orbiter support piece of the Ground Servicing Equipment (GSE). The initial purpose of the UCTS was to provide two support services to the Space Shuttle Orbiter immediately after landing at the Shuttle Landing Facility. The UCTS is designed with the capability of servicing future space vehicles; including all Space Station Requirements necessary for the MPLM Modules. The Simulation uses GSE Models to stand in for the actual systems to support testing of SCCS systems during their development. As an intern at Kennedy Space Center (KSC), my assignment was to develop a model component for the UCTS. I was given a fluid component (dryer) to model in Simulink. I completed training for UNIX and Simulink. The dryer is a Catch All replaceable core type filter-dryer. The filter-dryer provides maximum protection for the thermostatic expansion valve and solenoid valve from dirt that may be in the system. The filter-dryer also protects the valves from freezing up. I researched fluid dynamics to understand the function of my component. The filter-dryer was modeled by determining affects it has on the pressure and velocity of the system. I used Bernoulli's Equation to calculate the pressure and velocity differential through the dryer. I created my filter-dryer model in Simulink and wrote the test script to test the component. I completed component testing and captured test data. The finalized model was sent for peer review for any improvements. I participated in Simulation meetings and was involved in the subsystem design process and team collaborations. I gained valuable work experience and insight into a career path as an engineer.

  2. Economical Fabrication of Thick-Section Ceramic Matrix Composites

    Science.gov (United States)

    Babcock, Jason; Ramachandran, Gautham; Williams, Brian; Benander, Robert

    2010-01-01

    A method was developed for producing thick-section [>2 in. (approx.5 cm)], continuous fiber-reinforced ceramic matrix composites (CMCs). Ultramet-modified fiber interface coating and melt infiltration processing, developed previously for thin-section components, were used for the fabrication of CMCs that were an order of magnitude greater in thickness [up to 2.5 in. (approx.6.4 cm)]. Melt processing first involves infiltration of a fiber preform with the desired interface coating, and then with carbon to partially densify the preform. A molten refractory metal is then infiltrated and reacts with the excess carbon to form the carbide matrix without damaging the fiber reinforcement. Infiltration occurs from the inside out as the molten metal fills virtually all the available void space. Densification to coatings to the fiber preform was also required to accommodate the high preform thickness. The thick-section CMC processing developed in this work proved to be invaluable for component development, fabrication, and testing in two complementary efforts. In a project for the Army, involving SiC/SiC blisk development, nominally 0.8 in. thick x 8 in. diameter (approx. 2 cm thick x 20 cm diameter) components were successfully infiltrated. Blisk hubs were machined using diamond-embedded cutting tools and successfully spin-tested. Good ply uniformity and extremely low residual porosity (matrix composites fabricated via CVI or PIP. The pyrolytic carbon/zirconium nitride interface coating optimized in this work for use on carbon fibers was incorporated in the SiC/SiC composites and yielded a >41 ksi (approx. 283 MPa) flexural strength.

  3. Development of Self-Cleaning Denim Fabrics

    Science.gov (United States)

    Uğur, Ş. S.; Sarıışık, A. M.; Çavuşlar, E.; Ertek, M.

    2017-10-01

    Denim fabrics coated with TiO2 nanolayers for self-cleaning properties by using a continuous layer-by-layer method. Nanolayer coated denim fabrics washed with an enzyme process for aging affect. Fabrics were analyzed with SEM-EDX and XPS measurements. Self-cleaning properties of the nanolayer deposited denim fabrics were tested according to red wine stain against to Suntest visible light irradiation after 72 h. And also, some physical (air permeability, tensile strength) and color (color difference and rubbing fastness) properties were evaluated.

  4. Photolithography and Micro-Fabrication/ Packaging Laboratories

    Data.gov (United States)

    Federal Laboratory Consortium — The Photolithography and Micro-Fabrication/Packaging laboratories provide research level semiconductor processing equipment and facilities that do not require a full...

  5. Advances in superconducting quantum electronic microcircuit fabrication

    International Nuclear Information System (INIS)

    Kirschman, R.K.; Notarys, H.A.; Mercereau, J.E.

    1975-01-01

    Standard microelectronic fabrication techniques were utilized to produce batch quantities of superconducting quantum electronic devices and circuits. The over-all goal is a fabrication technology yielding circuits that are rugged, stable, and capable of being fabricated controllably and reproducibly in sizeable quantities. Progress toward this goal is presented, with primary emphasis on the most recent work, which includes the use of electron-beam lithography and techniques of hybrid microelectronics. Several prototype microcircuits were successfully fabricated. These microcircuits are formed in a thin-film parent material consisting of layers of superconducting and normal metals, and use proximity effect structures as the active circuit elements

  6. Development of blanket box structure fabrication technology

    International Nuclear Information System (INIS)

    Mohri, K.; Sato, S.; Kawaguchi, I.; Sato, K.; Kuroda, T.; Hashimoto, T.; Sato, S.; Takatsu, H.

    1995-01-01

    Fabrication studies have been performed for the first wall and blanket box structure in the fusion experimental reactor designed in Japan. The hot isostatic pressing technique has been proposed as one of the most promising candidate methods for fabricating the first wall. This paper describes the trial fabrication of a half-scale mock-up for part of an outboard module near the midplane, without the internal structure of a breeding region, to investigate its feasibility and to clarify technological issues associated with the proposed fabrication technologies. (orig.)

  7. Propulsion Design with Freeform Fabrication, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — Propulsion Design with Freeform Fabrication (PDFF) will develop and implement a novel design methodology that leverages the rapidly evolving Solid Freeform...

  8. Fabrication of Games and Learning

    DEFF Research Database (Denmark)

    Schoenau-Fog, Henrik; Reng, Lars; Kofoed, Lise

    2015-01-01

    The concept of Game based learning has proven to have many possibilities for supporting better learning outcomes, when using educational or commercial games in the classroom. However, there is also a great potential in using game development as a motivator in several other kinds of learning...... scenarios. Using game development as an approach for including game based learning in various educations has become more accessible due to more user friendly game development tools and systems. This study will thus focus on an exploration on how game development motivates students and what they learn when...... creating games. We exemplify the potential of using game fabrication as a learning environment with the investigation of a game production, which involved over 25 students across semesters. In order to investigate students’ experiences during this purposive game production, we set up an experiment where...

  9. Remote Microelectronics Fabrication Laboratory MEFLab

    Directory of Open Access Journals (Sweden)

    Jan Machotka

    2008-07-01

    Full Text Available Over the last decade, there has been a move towards using remote laboratories in engineering education. The majority of these laboratories are static, involving limited user-controlled mechanical movements. The University of South Australia has developed such a laboratory, called NetLab that has been successfully utilized for teaching both on-campus and transnational programs in electrical and electronics engineering. Following this success, we are now developing a remote laboratory for microelectronic fabrication, MEFLab. The first stage of the development is a remote laboratory for visual inspection and testing of electronic circuits directly on the silicon wafer under a microscope which is normally conducted in a cleanroom. The major challenge of this project is the accurate positioning of micro-probes remotely over the internet. This paper presents the details of the setup of this new remote laboratory, with a particular emphasis on the development of the hardware, software and graphical user interface.

  10. Fabrication of Metallic Hollow Nanoparticles

    Science.gov (United States)

    Kim, Jae-Woo (Inventor); Choi, Sr., Sang H. (Inventor); Lillehei, Peter T. (Inventor); Chu, Sang-Hyon (Inventor); Park, Yeonjoon (Inventor); King, Glen C. (Inventor); Elliott, James R. (Inventor)

    2016-01-01

    Metal and semiconductor nanoshells, particularly transition metal nanoshells, are fabricated using dendrimer molecules. Metallic colloids, metallic ions or semiconductors are attached to amine groups on the dendrimer surface in stabilized solution for the surface seeding method and the surface seedless method, respectively. Subsequently, the process is repeated with additional metallic ions or semiconductor, a stabilizer, and NaBH.sub.4 to increase the wall thickness of the metallic or semiconductor lining on the dendrimer surface. Metallic or semiconductor ions are automatically reduced on the metallic or semiconductor nanoparticles causing the formation of hollow metallic or semiconductor nanoparticles. The void size of the formed hollow nanoparticles depends on the dendrimer generation. The thickness of the metallic or semiconductor thin film around the dendrimer depends on the repetition times and the size of initial metallic or semiconductor seeds.

  11. Conception and construction rules for mechanical components of PWR nuclear island

    International Nuclear Information System (INIS)

    1988-06-01

    These rules of conception and construction for mechanical components of PWR nuclear island used in France are divided into 5 tomes bearing on: Tome 1: components of nuclear islands - Tome 2: materials - Tome 3: control methods - Tome 4: welding - Tome 5: fabrication [fr

  12. Coating of TPU-PDMS-TMS on Polycotton Fabrics for Versatile Protection

    Directory of Open Access Journals (Sweden)

    Arsheen Moiz

    2017-11-01

    Full Text Available This research aims to develop a non-fluorine based and durable coating technology that brings excellent hydrophobic, oleophobic and aqueous liquid repellent properties to polycotton fabrics (blend ratio 80/20 for cotton/polyester while maintaining comfort to an acceptable level. A crosslinked network from thermoplastic polyurethane (TPU, polydimethylsiloxane (PDMS and trimethylated silica (TMS has been formed on the surface of polycotton fabrics by the conventional padding-knife coating-padding-curing technique. A series of characterizations have been conducted to understand the chemical components, morphology, versatile protection and comfort of the coated fabrics. The TPU-PDMS-TMS (TPT coated fabrics showed a high hydrophobic surface with a high water contact angle of 142°, and the coating was durable against different cycles of laundering and crocking. The coated fabrics also showed excellent repellency against oils, liquids and chemicals for a long period of time. The coating has affected the air permeability and water vapor permeability together with the moisture management property of the polycotton fabrics, and the thermal resistance of the polycotton fabric has been enhanced at the same time. The coating technology developed can be further applied in protective clothing and functional textiles in different areas including military, mining and outdoor protection gear.

  13. [Study of nondestructive and fast identification of fabric fibers using near infrared spectroscopy].

    Science.gov (United States)

    Yuan, Hong-Fu; Chang, Rui-Xue; Tian, Ling-Ling; Song, Chun-Feng; Yuan, Xue-Qin; Li, Xiao-Yu

    2010-05-01

    A fast and nondestructive identification method to distinguish different types of fabric fibers is proposed in the present paper. A total of 214 fabric fiber samples, including wool, cashmere, terylene, polyamide, polyurethane, silk, flax, linen, cotton, viscose, cotton-flax blending, terylene-cotton blending, and wool-cashmere blending, were collected from Beijing Textile Fibre Inspection Institute. They contain yarns, raw wool or cashmere, and various fabric straps with different colors and different braid patterns. Sample presentation for measuring near infrared spectra of various textile fibers was tried to reduce the impact from the ununiformity of polymorphous fabric structure. Spectral data were pretreated using multiplicative signal correction (MSC) to reduce the influence of spectral noise and baseline shift. Classification of 12 kinds of fabric fibers in various braid patterns was studied using minimum spanning tree method and soft independent modeling of class analogy (SIMCA) classification based on principal component analysis of NIR spectra. The minimum spanning tree for the spectra of total samples shows that the samples in the same type fall almost into one cluster, but there are overlaps between some two different clusters of fabric fibers with very similar chemical compositions, such as wool and cashmere. Complete discrimination between cashmere and wool has been achieved using SIMCA. The results show that nondestructive and fast identification of fabric fibers using near infrared spectral technique is potentially feasible.

  14. FABRICATION OF WINDOW SADDLES FOR NIF CRYOGENIC HOHLRAUMS

    International Nuclear Information System (INIS)

    GIRALDEZ, E; KAAE, J.L

    2003-09-01

    OAK-B135 A planar diagnostic viewing port attached to the cylindrical wall of the NIF cryogenic hohlraum requires a saddle-like transition piece. While the basic design of this window saddle is straightforward, its fabrication is not, given the scale and precision of the component. They solved the problem through the use of a two segment copper mandrel to electroform the gold window saddle. The segments were micro-machined using a combination of single-point diamond turning and single point diamond milling. These processes as well as the electroplating conditions, final machining and mandrel removal are described in this paper

  15. The study and fabrication of DLC micropattern on roll mold

    Science.gov (United States)

    Kwon, Young Woo; Lee, Tae Dong; Park, Yeong Min; Cho, Hyun; Kim, Jin Kon; Kim, Tae Gyu

    2015-03-01

    Diamond-like carbon (DLC) coating is becoming a promising protective coating layers due to its superior properties. In this study, instead of protective coating, DLC film was applied as the only component for micropattern then etched with lithography and lift-off process selectively. Furthermore, DLC film has been fabricated on aluminum roll mold. Then UV curing resin was applied to form the pattern on the polyethylene terephthalate (PET) film. The dimension and formation of the DLC micropattern on roll mold were analyzed. Moreover, the Raman spectroscopic of nitrogen-doped DLC film was analyzed.

  16. Electrofluidics fabricated by space-selective metallization in glass microfluidic structures using femtosecond laser direct writing.

    Science.gov (United States)

    Xu, Jian; Wu, Dong; Hanada, Yasutaka; Chen, Chi; Wu, Sizhu; Cheng, Ya; Sugioka, Koji; Midorikawa, Katsumi

    2013-12-07

    Space-selective metallization of the inside of glass microfluidic structures using femtosecond laser direct-write ablation followed by electroless plating is demonstrated. Femtosecond laser direct writing followed by thermal treatment and successive chemical etching allows us to fabricate three-dimensional microfluidic structures inside photosensitive glass. Then, femtosecond laser ablation followed by electroless metal plating enables flexible deposition of patterned metal films on desired locations of not only the top and bottom walls but also the sidewalls of fabricated microfluidic structures. A volume writing scheme for femtosecond laser irradiation inducing homogeneous ablation on the sidewalls of microfluidic structures is proposed for sidewall metallization. The developed technique is used to fabricate electrofluidics in which microelectric components are integrated into glass microchannels. The fabricated electrofluidics are applied to control the temperature of liquid samples in the microchannels for the enhancement of chemical reactions and to manipulate the movement of biological samples in the microscale space.

  17. Design and fabrication of high power microwave window for 4 MeV LINAC

    International Nuclear Information System (INIS)

    Syunry, T.S.; Bhide, S.S.; Madan, R.S.; Das, S.; D'Sa, J.M.

    1988-01-01

    One of the critical components in the design and fabrication of 4 MeV LINAC is the R.F. window, through which 2 MW pulse R.F. power at 3 GHZ passes from the high pressure side to the chain of cavities under very high vacuum. Readymade windows, which can be incorporated in the LINAC are not easily available. These windows were fabricated inhouse, based upon some standard designs available in literature. However, the fabrication technique proved to be very difficult. The windows have been made successfully and tested for microwave performance. They were also rigorously thermally cycled and pressure tested. Fabrication details, test procedures and data are reported in this paper. (author). 5 figs., 2 tables

  18. Bayesian Independent Component Analysis

    DEFF Research Database (Denmark)

    Winther, Ole; Petersen, Kaare Brandt

    2007-01-01

    In this paper we present an empirical Bayesian framework for independent component analysis. The framework provides estimates of the sources, the mixing matrix and the noise parameters, and is flexible with respect to choice of source prior and the number of sources and sensors. Inside the engine...... in a Matlab toolbox, is demonstrated for non-negative decompositions and compared with non-negative matrix factorization.......In this paper we present an empirical Bayesian framework for independent component analysis. The framework provides estimates of the sources, the mixing matrix and the noise parameters, and is flexible with respect to choice of source prior and the number of sources and sensors. Inside the engine...

  19. Adaptable component frameworks

    DEFF Research Database (Denmark)

    Katajainen, Jyrki; Simonsen, Bo

    2009-01-01

    for vector, which is undoubtedly the most used container of the C++ standard library. In particular, we specify the details of a vector implementation that is safe with respect to referential integrity and strong exception safety. Additionally, we report the experiences and lessons learnt from......The CPH STL is a special edition of the STL, the containers and algorithms part of the C++ standard library. The specification of the generic components of the STL is given in the C++ standard. Any implementation of the STL, e.g. the one that ships with your standard-compliant C++ compiler, should...... the development of component frameworks which we hope to be of benefit to persons engaged in the design and implementation of generic software libraries....

  20. Bacterial Cell Wall Components

    Science.gov (United States)

    Ginsberg, Cynthia; Brown, Stephanie; Walker, Suzanne

    Bacterial cell-surface polysaccharides cells are surrounded by a variety of cell-surface structures that allow them to thrive in extreme environments. Components of the cell envelope and extracellular matrix are responsible for providing the cells with structural support, mediating intercellular communication, allowing the cells to move or to adhere to surfaces, protecting the cells from attack by antibiotics or the immune system, and facilitating the uptake of nutrients. Some of the most important cell wall components are polysaccharide structures. This review discusses the occurrence, structure, function, and biosynthesis of the most prevalent bacterial cell surface polysaccharides: peptidoglycan, lipopolysaccharide, arabinogalactan, and lipoarabinomannan, and capsular and extracellular polysaccharides. The roles of these polysaccharides in medicine, both as drug targets and as therapeutic agents, are also described.

  1. FIBROUS MONOLITH WEAR RESISTANT COMPONENTS FOR THE MINING INDUSTRY

    Energy Technology Data Exchange (ETDEWEB)

    Mark J. Rigali; Kenneth L. Knittel; Mike L. Fulcher

    2002-03-01

    During this reporting period, work continued on development of formulations using the materials identified as contenders for the fibrous monolith wear resistant components. The FM structures fabricated were: diamond/WC-Co, B{sub 4}C/WC-Co, TiB{sub 2}/WC-Co, WC-Co/Co, WC-Co/WC-Co. Results of our consolidation densification studies on these systems lead to the down-selection of WC-Co/WC-Co, WC-Co/Co and diamond/WC-Co for further development for mining applications including drill bit inserts, roof bit inserts, radial tools conical tools and wear plates (WC-Co based system only) for earth moving equipment. Prototype component fabrication focused on the fabrication of WC-Co/WC-Co FM conical tools, diamond/WC-Co coated drill bit insert prototypes. Fabrication of WC-Co/WC-Co FM insert prototypes for a grader blade is also underway. ACR plans to initiate field-testing of the drill bit insert prototypes and the grader blade insert this summer (2002). The first WC-Co/WC-Co FM conical tool prototypes were sent to Kennametal for evaluation towards the end of the current reporting period.

  2. Components of the environment

    International Nuclear Information System (INIS)

    Klinda, J.; Lieskovska, Z.

    1998-01-01

    This report of the Ministry of the Environment of the Slovak Republic deals with the components of the environment. The results of monitoring of air (emission situation), ambient air quality, atmospheric precipitation, tropospheric ozone, water (surface water, groundwater resources, waste water and drinking water), geological factors (geothermal energy, fuel deposits, ore deposits, non-metallic ore deposits), soil (area statistics, soil contamination. soil reaction and active extractable aluminium, soil erosion), flora and fauna (national strategy of biodiversity protection) are presented

  3. Surface mount component jig

    Science.gov (United States)

    Kronberg, James W.

    1990-08-07

    A device for bending and trimming the pins of a dual-inline-package component and the like for surface mounting rather than through mounting to a circuit board comprises, in a first part, in pin cutter astride a holder having a recess for holding the component, a first spring therebetween, and, in a second part, two flat members pivotally interconnected by a hinge and urged to an upward peaked position from a downward peaked position by a second spring. As a downward force is applied to the pin cutter it urges the holder downward, assisted by the first spring and a pair of ridges riding on shoulders of the holder, to carry the component against the upward peaked flat members which guide the pins outwardly. As the holder continues downwardly, the flat members pivot to the downward peaked position bending the pins upwardly against the sides of the holder. When the downward movement is met with sufficient resistance, the ridges of the pin cutter ride over the holder's shoulders to continue downward to cut any excess length of pin.

  4. Design, fabrication and testing of hierarchical micro-optical structures and systems

    Science.gov (United States)

    Cannistra, Aaron Thomas

    Micro-optical systems are becoming essential components in imaging, sensing, communications, computing, and other applications. Optically based designs are replacing electronic, chemical and mechanical systems for a variety of reasons, including low power consumption, reduced maintenance, and faster operation. However, as the number and variety of applications increases, micro-optical system designs are becoming smaller, more integrated, and more complicated. Micro and nano-optical systems found in nature, such as the imaging systems found in many insects and crustaceans, can have highly integrated optical structures that vary in size by orders of magnitude. These systems incorporate components such as compound lenses, anti-reflective lens surface structuring, spectral filters, and polarization selective elements. For animals, these hybrid optical systems capable of many optical functions in a compact package have been repeatedly selected during the evolutionary process. Understanding the advantages of these designs gives motivation for synthetic optical systems with comparable functionality. However, alternative fabrication methods that deviate from conventional processes are needed to create such systems. Further complicating the issue, the resulting device geometry may not be readily compatible with existing measurement techniques. This dissertation explores several nontraditional fabrication techniques for optical components with hierarchical geometries and measurement techniques to evaluate performance of such components. A micro-transfer molding process is found to produce high-fidelity micro-optical structures and is used to fabricate a spectral filter on a curved surface. By using a custom measurement setup we demonstrate that the spectral filter retains functionality despite the nontraditional geometry. A compound lens is fabricated using similar fabrication techniques and the imaging performance is analyzed. A spray coating technique for photoresist

  5. Fabrication and characterization of magnetic nanoparticle composite membranes

    Science.gov (United States)

    Cruickshank, Akeem Armand

    To effectively and accurately deliver drugs within the human body, both new designs and components for implantable micropumps are being studied. Designs must ensure high biocompatibility, drug compatibility, accuracy and small power consumption. The focus of this thesis was to fabricate a prototype magnetic nanoparticle membrane for eventual incorporation into a biomedical pump and then determine the relationship between this membrane deflection and applied pneumatic or magnetic force. The magnetic nanoparticle polymer composite (MNPC) membranes in this study were composed of crosslinked polydimethylsiloxane (PDMS) and iron oxide nanoparticles (IONPs). An optimal iron oxide fabrication route was identified and particle size in each batch was approximately 24.6 nm. Once these nanoparticles were incorporated into a membrane (5 wt. %), the nanoparticle formed agglomerates with an average diameter of 2.26 +/-1.23 microm. Comparisons between the 0 and 5 wt. % loading of particles into the membranes indicated that the elastic modulus of the composite decreased with increasing particle concentration. The pressure- central deflection of the membranes could not be predicated by prior models and variation between magnetic and pneumatic pressure-deflection curves was quantified. Attempts to fabricate membranes with above 5 wt. % nanoparticles were not successful (no gelation). Fourier Transform Infrared (FTIR) spectroscopy results suggest that excess oleic acid on the nanoparticles prior to mixing might have prevented crosslinking.

  6. Design and Fabrication of Vertically-Integrated CMOS Image Sensors

    Directory of Open Access Journals (Sweden)

    Orit Skorka

    2011-04-01

    Full Text Available Technologies to fabricate integrated circuits (IC with 3D structures are an emerging trend in IC design. They are based on vertical stacking of active components to form heterogeneous microsystems. Electronic image sensors will benefit from these technologies because they allow increased pixel-level data processing and device optimization. This paper covers general principles in the design of vertically-integrated (VI CMOS image sensors that are fabricated by flip-chip bonding. These sensors are composed of a CMOS die and a photodetector die. As a specific example, the paper presents a VI-CMOS image sensor that was designed at the University of Alberta, and fabricated with the help of CMC Microsystems and Micralyne Inc. To realize prototypes, CMOS dies with logarithmic active pixels were prepared in a commercial process, and photodetector dies with metal-semiconductor-metal devices were prepared in a custom process using hydrogenated amorphous silicon. The paper also describes a digital camera that was developed to test the prototype. In this camera, scenes captured by the image sensor are read using an FPGA board, and sent in real time to a PC over USB for data processing and display. Experimental results show that the VI-CMOS prototype has a higher dynamic range and a lower dark limit than conventional electronic image sensors.

  7. Design and fabrication of vertically-integrated CMOS image sensors.

    Science.gov (United States)

    Skorka, Orit; Joseph, Dileepan

    2011-01-01

    Technologies to fabricate integrated circuits (IC) with 3D structures are an emerging trend in IC design. They are based on vertical stacking of active components to form heterogeneous microsystems. Electronic image sensors will benefit from these technologies because they allow increased pixel-level data processing and device optimization. This paper covers general principles in the design of vertically-integrated (VI) CMOS image sensors that are fabricated by flip-chip bonding. These sensors are composed of a CMOS die and a photodetector die. As a specific example, the paper presents a VI-CMOS image sensor that was designed at the University of Alberta, and fabricated with the help of CMC Microsystems and Micralyne Inc. To realize prototypes, CMOS dies with logarithmic active pixels were prepared in a commercial process, and photodetector dies with metal-semiconductor-metal devices were prepared in a custom process using hydrogenated amorphous silicon. The paper also describes a digital camera that was developed to test the prototype. In this camera, scenes captured by the image sensor are read using an FPGA board, and sent in real time to a PC over USB for data processing and display. Experimental results show that the VI-CMOS prototype has a higher dynamic range and a lower dark limit than conventional electronic image sensors.

  8. Heater Development, Fabrication, and Testing: Analysis of Fabricated Heaters

    Science.gov (United States)

    Bragg-Sitton, S. M.; Dickens, R. E.; Farmer, J. T.; Davis, J. D.; Adams, M. R.; Martin, J. J.; Webster, K. L.

    2008-01-01

    Thermal simulators (highly designed heater elements) developed at the Early Flight Fission Test Facility (EFF-TF) are used to simulate the heat from nuclear fission in a variety of reactor concepts. When inserted into the reactor geometry, the purpose of the thermal simulators is to deliver thermal power to the test article in the same fashion as if nuclear fuel were present. Considerable effort has been expended to mimic heat from fission as closely as possible. To accurately represent the fuel, the simulators should be capable of matching the overall properties of the nuclear fuel rather than simply matching the fuel temperatures. This includes matching thermal stresses in the pin, pin conductivities, total core power, and core power profile (axial and radial). This Technical Memorandum discusses the historical development of the thermal simulators used in nonnuclear testing at the EFF-TF and provides a basis for the development of the current series of thermal simulators. The status of current heater fabrication and testing is assessed, providing data and analyses for both successes and failures experienced in the heater development and testing program.

  9. New Fabrication Strategies for Polymer Electrolyte Batteries

    National Research Council Canada - National Science Library

    Shriver, D

    1997-01-01

    .... The objective of this research was to fabricate lithium-polymer batteries by techniques that may produce a thin electrolyte and cathode films and with minimal contamination during fabrication. One such technique, ultrasonic spray was used. Another objective of this research was to test lithium cells that incorporate the new polymer electrolytes and polyelectrolytes.

  10. Fuel pellets of various shapes- fabrication experience

    International Nuclear Information System (INIS)

    Ramachandran, R.; Nair, M.R.; Majumdar, S.; Purushotham, D.S.C.

    1996-10-01

    Sintered uranium oxide and mixed oxide pellets are extensively used as nuclear reactor fuel. The shape of the fuel-pellets influence greatly their in-reactor performance. Fuel pellets of various shapes were prepared in Radiometallurgy Division to study their fabricability and in-reactor performance. This paper presents the experience in fabricating these fuel pellets. (author)

  11. Investigations of fabric stratifiers for solar tanks

    DEFF Research Database (Denmark)

    Andersen, Elsa; Furbo, Simon; Fan, Jianhua

    2005-01-01

    water. In this paper investigations of a number of different fabric stratification pipes are presented and compared to a non flexible inlet stratifier. Additional, detailed investigations of the flow structure close to two fabric stratification pipes are presented for one set of operating conditions...

  12. Fabrication of Polymer Optical Fibre (POF) Gratings.

    Science.gov (United States)

    Luo, Yanhua; Yan, Binbin; Zhang, Qijin; Peng, Gang-Ding; Wen, Jianxiang; Zhang, Jianzhong

    2017-03-04

    Gratings inscribed in polymer optical fibre (POF) have attracted remarkable interest for many potential applications due to their distinctive properties. This paper overviews the current state of fabrication of POF gratings since their first demonstration in 1999. In particular we summarize and discuss POF materials, POF photosensitivity, techniques and issues of fabricating POF gratings, as well as various types of POF gratings.

  13. Fuel Fabrication Capability Research and Development Plan

    Energy Technology Data Exchange (ETDEWEB)

    Senor, David J.; Burkes, Douglas

    2013-06-28

    The purpose of this document is to provide a comprehensive review of the mission of the Fuel Fabrication Capability (FFC) within the Global Threat Reduction Initiative (GTRI) Convert Program, along with research and development (R&D) needs that have been identified as necessary to ensuring mission success. The design and fabrication of successful nuclear fuels must be closely linked endeavors.

  14. Fabrication of photonic crystals and Nanocavities

    NARCIS (Netherlands)

    Woldering, L.A.

    2008-01-01

    The fabrication of three-dimensional inverse woodpile photonic crystals is highly desirable because of their predicted large photonic band gap, their conceptual ease of fabrication, and their robustness to withstand deviations from the ideal geometry that are intrinsic to nanofabrication. In this

  15. Fabrication, Morphological and Optoelectronic Properties of ...

    African Journals Online (AJOL)

    We report on the fabrication and characterization of MSM photodetector. We investigated the surface morphological and the structural properties of the porous silicon by optical microscopy, atomic force microscope (AFM) and X-ray diffraction. The metal–semiconductor–metal photodetector were fabricated by using Sb as ...

  16. Properties of natural fabric Polyalthia cerasoides

    CSIR Research Space (South Africa)

    Jayaramudu, J

    2009-06-01

    Full Text Available . The tensile properties were also studied. The effect of alkali treatment on the properties of the fabric was studied. The FTIR and chemical analyses indicated lowering of hemi-cellulose and lignin content on alkali treatment of the fabric. The tensile...

  17. Development of automated welding process for field fabrication of thick walled pressure vessels

    Energy Technology Data Exchange (ETDEWEB)

    Schneider, U A

    1981-01-01

    Research on automatic welding processes for the fabrication of thick-walled pressure vessels continued. A literature review on the subject was completed. A laboratory study of criteria for judging acceptable root parameters continued. Equipment for a demonstration facility to test the components and processes of the automated welding system has been specified and is being obtained. (LCL)

  18. Practice of the RCC-C for fabrication of large hardware equipments

    International Nuclear Information System (INIS)

    Gandrey, L.

    1983-03-01

    Presentation of FRAMATOME experience concerning practice of RCC-M (French design and construction rules for nuclear power plant components) to the fabrication of large equipments for primary circuits (tanks, vapor generators, pressurizers): utilization of the design and calculation rules, development of welding, enhancement of various controls (e.g. ultrasonic controls); study of their adaptability, occured problems, required investments, ... [fr

  19. Fabrication of a screw-retained fixed provisional prosthesis supported by dental implants.

    Science.gov (United States)

    Kökat, Ali Murat; Akça, Kivanç

    2004-03-01

    Screw-retained provisional implant-supported prostheses may have advantages over cement-retained prostheses in certain situations. This article describes a technique for fabrication of screw-retained provisional acrylic resin implant-supported prostheses from the modified metal components provided with the implant.

  20. Beryllium application in ITER plasma facing components

    International Nuclear Information System (INIS)

    Raffray, A.R.; Federici, G.; Barabash, V.; Cardella, A.; Jakeman, R.; Ioki, K.; Janeschitz, G.; Parker, R.; Tivey, R.; Pacher, H.D.; Wu, C.H.; Bartels, H.W.

    1997-01-01

    Beryllium is a candidate armour material for the in-vessel components of the International Thermonuclear Experimental Reactor (ITER), namely the primary first wall, the limiter, the baffle and the divertor. However, a number of issues arising from the performance requirements of the ITER plasma facing components (PFCs) must be addressed to better assess the attractiveness of Be as armour for these different components. These issues include heat loading limits arising from temperature and stress constraints under steady state conditions, armour lifetime including the effects of sputtering erosion as well as vaporisation and loss of melt during disruption events, tritium retention and permeation, and chemical hazards, in particular with respect to potential Be/steam reaction. Other issues such as fabrication and the possibility of in-situ repair are not performance-dependent but have an important impact on the overall assessment of Be as PFC armour. This paper describes the present view on Be application for ITER PFCs. The key issues are discussed including an assessment of the current level of understanding based on analysis and experimental data; and on-going activities as part of the ITER EDA R and D program are highlighted. (orig.)

  1. Thermoelectric Fabrics: Toward Power Generating Clothing

    Science.gov (United States)

    Du, Yong; Cai, Kefeng; Chen, Song; Wang, Hongxia; Shen, Shirley Z.; Donelson, Richard; Lin, Tong

    2015-01-01

    Herein, we demonstrate that a flexible, air-permeable, thermoelectric (TE) power generator can be prepared by applying a TE polymer (e.g. poly(3,4-ethylenedioxythiophene):poly(4-styrenesulfonate)) coated commercial fabric and subsequently by linking the coated strips with a conductive connection (e.g. using fine metal wires). The poly(3,4-ethylenedioxythiophene):poly(4-styrenesulfonate) coated fabric shows very stable TE properties from 300 K to 390 K. The fabric device can generate a TE voltage output (V) of 4.3 mV at a temperature difference (ΔT) of 75.2 K. The potential for using fabric TE devices to harvest body temperature energy has been discussed. Fabric-based TE devices may be useful for the development of new power generating clothing and self-powered wearable electronics. PMID:25804132

  2. Fabricating 3D figurines with personalized faces.

    Science.gov (United States)

    Tena, J Rafael; Mahler, Moshe; Beeler, Thabo; Grosse, Max; Hengchin Yeh; Matthews, Iain

    2013-01-01

    We present a semi-automated system for fabricating figurines with faces that are personalised to the individual likeness of the customer. The efficacy of the system has been demonstrated by commercial deployments at Walt Disney World Resort and Star Wars Celebration VI in Orlando Florida. Although the system is semi automated, human intervention is limited to a few simple tasks to maintain the high throughput and consistent quality required for commercial application. In contrast to existing systems that fabricate custom heads that are assembled to pre-fabricated plastic bodies, our system seamlessly integrates 3D facial data with a predefined figurine body into a unique and continuous object that is fabricated as a single piece. The combination of state-of-the-art 3D capture, modelling, and printing that are the core of our system provide the flexibility to fabricate figurines whose complexity is only limited by the creativity of the designer.

  3. Moisture management properties of Cupro knitted fabrics

    Science.gov (United States)

    Durur, G.; Oner, E.; Gunduz, G.

    2017-10-01

    On the purpose of analysing the moisture management behaviour of Cupro blend knitted fabrics made of Ne 40/1 and Ne 56/1 cotton/Cupro blend yarns, which have single jersey, 1x1 rib and interlock knitting types were systematically produced. Multi-dimensional liquid transport properties of the produced fabric were measured on the Moisture Management Tester (MMT). The air permeability and some structural properties of the fabrics were also measured, and the results were evaluated taking into account moisture management properties. According to results, it is observed that moisture management capacity and permeability of Cupro blends produced from finer yarns were higher than those of fabrics from coarse count yarns. Generally, Cupro blend knitted fabrics showed good moisture management properties.

  4. Feasibility of the fabrication of americium targets

    International Nuclear Information System (INIS)

    Haas, D.; Somers, J.

    1999-01-01

    The paper compares the processes used at ITU for the fabrication of americium targets for transmutation: powder mixing process, sol-gel method and the infiltration by an active solution of inactive pellets. The advantages of the latter process, related mainly to the lower level of dust formation, are stressed. Moreover, the radiological constraints on the fabrication as a function of Am content and of selected fabrication process are evaluated. As conclusion, the feasibility of Am target fabrication has been demonstrated on a laboratory scale, based on experimental results evaluation. The penalties due to radiological constraints in a semi-industrial process are acceptable. The future developments consist in the construction of a laboratory fully dedicated to minor actinides fuel pins or targets fabrication. (author)

  5. Composite metal foil and ceramic fabric materials

    Science.gov (United States)

    Webb, Brent J.; Antoniak, Zen I.; Prater, John T.; DeSteese, John G.

    1992-01-01

    The invention comprises new materials useful in a wide variety of terrestrial and space applications. In one aspect, the invention comprises a flexible cloth-like material comprising a layer of flexible woven ceramic fabric bonded with a layer of metallic foil. In another aspect, the invention includes a flexible fluid impermeable barrier comprising a flexible woven ceramic fabric layer having metal wire woven therein. A metallic foil layer is incontinuously welded to the woven metal wire. In yet another aspect, the invention includes a material comprising a layer of flexible woven ceramic fabric bonded with a layer of an organic polymer. In still another aspect, the invention includes a rigid fabric structure comprising a flexible woven ceramic fabric and a resinous support material which has been hardened as the direct result of exposure to ultraviolet light. Inventive methods for producing such material are also disclosed.

  6. Patterned Woven Fabrics in Lithuanian Folk Skirts

    Directory of Open Access Journals (Sweden)

    Eglė KUMPIKAITĖ

    2014-06-01

    Full Text Available In the article 258 Lithuanian folk skirts from National M. K. Čiurlionis Museum of Art and 85 skirts from Lithuanian Open Air Museum are investigated. The weaves and plans of weave of skirts fabrics are made. Also the composing of plans of weave is analysed in aspect of segment, ornament and symmetry group of patterned fabric weave. Also the symmetry groups of Lithuanian folk skirts fabrics and their distribution according to the fabric weave are analysed. The tendencies of symmetry groups and peculiarities of composing of plans of weave can help to recreate the reconstructions of authentic folk fabrics. DOI: http://dx.doi.org/10.5755/j01.ms.20.2.1950

  7. Fabrication drawings of fuel pins for FUJI project among PSI, JNC and NRG. Revised version

    International Nuclear Information System (INIS)

    Ozawa, Takayuki; Nakazawa, Hiroaki; Abe, Tomoyuki; Nagayama, Masahiro

    2002-02-01

    Irradiation tests and post-irradiation examinations in the framework of JNC-PSI-NRG collaboration project will be performed in 2003-2005. Irradiation fuel pins will be fabricated by the middle of 2003. The fabrication procedure for irradiation fuel pins has been started in 2001. Several fabrication tests and qualification tests in JNC and PSI (Paul Scherrer Institute, Switzerland) have been performed before the fuel pin fabrication. According to the design assignment between PSI and JNC in the frame of this project, PSI should make a specification document for the fuel pellet, the sphere-pac fuel particles, the vipac fuel particles, and the fuel pin. JNC should make a fabrication drawing for irradiation pins. JNC has been performed the fuel design in cooperation with PSI and NRG (Nuclear Research and Consultancy Group, Netherlands). In this project, the pelletized fuel, the sphere-pac fuel, and the vipac fuel will be simultaneously irradiated on HFR (High Flux Reactor, Netherlands). This fabrication drawing has been made under the design assignment with PSI, and consists of the drawing of MOX pellet, thermal insulator pellet, pin components, fuel segments, and the constructed pin. The fabrication drawings were approved in October 2001, but after that, the optimization of specifications has been discussed and agreed among all partners. In this report, the revised fabrication drawings will be shown. Based on the commission of Plutonium Fuel Technology Group, Advanced Fuel Recycle Technology Division, this design work has been performed in Fuel Design and Evaluation Group, Plutonium Fuel Fabrication Division, Plutonium Fuel Center. (author)

  8. Solid freeform fabrication of biomaterials

    Science.gov (United States)

    Chu, Tien-Min Gabriel

    1999-12-01

    The biological performance of porous Hydroxyapatite (HA) is closely related to the pore architecture in the implants. The study on the effect of architecture to the biological performance of porous HA requires new manufacturing methods that can fabricate implants with controlled pores channels. In this thesis, four highly loaded HA and alumina suspensions were formulated and three different processes involving Solid Freeform Fabrication (SFF) were developed. An aqueous HA suspension in acrylamides was first formulated and the UV-curing properties were evaluated. With a medical grade HA powder, two non-aqueous HA suspensions were formulated: a 40 vol.% HA suspension in Hexanediol Diacrylate (HDDA) and a 40 vol.% HA suspension in 1:1 mix of Propoxylated Neopentyl Glycol Diacrylate (PNPGDA) and Isobomyl Acrylate (EBA). A 50 vol.% Alumina suspension in PNPGDA/IBA was also formulated. The effect of dispersant to the viscosity of the suspensions was characterized. In the Stereolithography (SL) method, the curing parameters of HA/HDDA and HA/PNPGDA/IBA were determined. Prototype HA implants with 1,700 mum internal channels were built directly on an SL Apparatus (SLA). The designed internal channel patterns were preserved after sintering. In the Ink-jet printing method, the high temperature flow behaviors of the suspensions were characterized. The effects of solids loading to the viscosity of the suspensions were modeled with Krieger-Dougherty equation. Leveling theory developed in paint industry was employed to analyze the self-leveling capability of the suspensions. In the indirect SL method, the thermal curing behavior of HA and alumina suspensions were characterized. The total cure time was measured and the curing kinetics was modeled. Negative molds for the implants were designed and built on SLA with epoxy resin. HA/PNPGDA/IBA was cast into the mold and cured in an oven. The binders and the epoxy mold were pyrolyzed and the green bodies sintered. Internal channels

  9. Long wavelength MSM photodetectors fabricated on InGaNAs

    Science.gov (United States)

    Gouin, François; Noad, Julian; Higgins, Erle; Coulas, David

    2006-02-01

    Recently there has been a great deal of interest in the growth of dilute nitride quaternary alloys, such as InGaNAs, on GaAs substrates for the fabrication of GaAs-based components and optoelectronic integrated circuits. The addition of indium to the binary compound GaAs produces a ternary with a lower bandgap and larger lattice constant. The incorporation of nitrogen in this ternary further decreases the bandgap while reducing the lattice constant. This makes it possible to grow material lattice-matched to a GaAs substrate but with a narrower bandgap offering the possibility of growing materials suitable for opto-electronic devices on a GaAs substrate while operating at wavelengths used in long-distance optical communications. These devices can then be integrated with mature GaAs device technologies (MESFET, HBT) in photoreceivers and receivers/transmitters for improved functionality and reliability, lower cost, reduced size, etc. We have fabricated metal-semiconductor-metal (MSM) photodetectors on 1-μm thick In .1Ga .9N .03As .97 epilayers, a composition that results in a bandgap in the 1.3 μm region. We report on the DC characteristics, frequency dependence and wavelength dependence of the photoresponse. The results are compared to MSMs fabricated on GaAs. The temporal response is not as fast as that of GaAs MSMs and may be related to low carrier mobility. This shortcoming has been reported as the cause for the lower-than-expected efficiency of solar cells fabricated using this quarternary. The effect of growth conditions and thermal processing on detector characteristics such as bandwidth and dark current were investigated. The challenges associated with the use of InGaNAs in photodetectors (such as defects, response speed, requirement for thermal anneal) will be discussed.

  10. Scanning Probe Microscopy for Atomic-scale Silicon Device Fabrication

    Science.gov (United States)

    Simmons, Michelle

    2005-03-01

    Over the past three decades the driving force behind the expansion of the microelectronics industry has been the ability to pack ever more features onto a silicon chip, achieved by continually miniaturising the size of the individual components. However, after 2015 there is no known technological route to reduce device sizes below 10nm. In this talk we demonstrate a complete fabrication strategy towards atomic-scale device fabrication in silicon using a combination of scanning tunneling microscopy and high purity crystal growth. In particular we overcome one of the major obstacles to making functional semiconductor devices with an STM -- connecting macroscopic leads to the device once it is removed from the vacuum environment [1]. We demonstrate key steps of the fabrication process, including the ability to place individual phosphorus atoms in silicon at precise locations [2] and encapsulate them in epitaxial silicon with minimal diffusion and segregation of the dopants [3]. We present magnetoresistance data showing the cross-over from 2D to 1D transport in nano-scale quantum wires and arrays. Finally we discuss the implications of these results for the construction of more sophisticated atomic-scale devices in silicon such as a silicon based quantum computer. [1] F.J. Ruess, L. Oberbeck, M.Y. Simmons, K.E.J. Goh, A.R. Hamilton, T. Hallam, N.J. Curson and R.G. Clark, ``Fabrication of quantum wires using scanning probe microscopy'', Nano Letters 4, 1969 (2004). [2] S. R. Schofield, N. J. Curson, M. Y. Simmons, F. J. Ruess, T. Hallam, L. Oberbeck and R. G.Clark, ``Atomically precise placement of single dopants in silicon'', Physical Review Letters 91, 136104 (2003). [3] L. Oberbeck, N. J. Curson, T. Hallam, M. Y. Simmons and R.G. Clark, ``Measurement of phosphorus segregation in silicon at the atomic-scale using scanning tunneling microscopy'', Appl. Phys. Lett. 83, 1359 (2004).

  11. Progress in heavy ion-driven target fabrication and injection

    Science.gov (United States)

    Goodin, D. T.; Nobile, A.; Alexander, N. B.; Gallix, R.; Maxwell, J. L.; Petzoldt, R. W.; Rickman, W. S.; Valmianski, E. I.

    2005-05-01

    The target for an Inertial Fusion Energy (IFE) power plant is compressed and heated to fusion conditions by the driver beams. The "Target Fabrication Facility" (TFF) of a 1000 MW(e) IFE power plant must supply over 500,000 targets per day. The target is then injected into the target chamber at a rate of 5-10 Hz and tracked precisely so the driver beams can be directed to the target. The feasibility of developing successful fabrication and injection methodologies at the low cost required for energy production (about $0.25/target, about 10 4 less than current costs) is a critical issue for inertial fusion. The technologies for producing Heavy Ion Fusion (HIF) targets have significant overlaps and synergisms with current-day inertial fusion experimental targets and with laser fusion (direct drive) IFE targets. Capsule formation and characterization, permeation filling, and layering of the DT using a cryogenic fluidized bed are common methodologies shared between laser fusion and HIF. Specific to HIF targets are the techniques for fabricating and assembling the hohlraum components. We will report on experimental progress with the Laser-assisted Chemical Vapor Deposition (LCVD) technique to produce "micro-engineered" low-density metallic foams for the hohlraum, and calculations of hohlraums materials performance during handling. Fiber growth by LCVD in arrays has been demonstrated for the first time, important to achieve the volume production needed for IFE. We have also evaluated a variety of hohlraum material selections, with consideration of target physics, cost, ES&H, activation, and compatibility with the molten salt coolant. These materials include selections for once-through and for recycle scenarios. We have performed a cost analysis for an " nth-of-a-kind" Target Fabrication Facility using our current assumptions about the production processes. Some of these scenarios result in future target manufacturing costs consistent with economical electricity production.

  12. Analysis of Depth of Shade on Mercerized and Unmercerized Fabric among Different Woven Fabric Structures

    OpenAIRE

    Alam, Md Shamim

    2016-01-01

    The main objective of this paper is to analyze and compare the color strengths of mercerized and unmercerized fabric among different fabric structures. In this research work Remazol reactive dye and three types of woven fabrics were used such as 20⁎20 sheeting, 30⁎30 sheeting, and herringbone. Spectrophotometer was used to find out the amount of dye which is fixed in the fabrics after soap wash. Three different woven fabrics were dyed with reactive dye (Remazol Red, Remazol Yellow, and Remazo...

  13. Analysis Components Investigation Report

    Science.gov (United States)

    2014-10-01

    ssification a the marg ford and h ures such ge of this l s integratio PREVIOUS WRI ities. For in annotating ame meanin ck by valid rest. These ansion...ent to rder. order. rder el has d to the val, and learning , which ibrary is oo! and feature ovides a Analys 4 4 1 is Component THIS DOCU... learn m tor Machin sed to give to re-rank be execut he model w s the follow ed by any the trainin ciated with ation of the the docume all terms

  14. Impedance of accelerator components

    International Nuclear Information System (INIS)

    Corlett, J.N.

    1996-05-01

    As demands for high luminosity and low emittance particle beams increase, an understanding of the electromagnetic interaction of these beams with their vacuum chamber environment becomes more important in order to maintain the quality of the beam. This interaction is described in terms of the wake field in time domain, and the beam impedance in frequency domain. These concepts are introduced, and related quantities such as the loss factor are presented. The broadband Q = 1 resonator impedance model is discussed. Perturbation and coaxial wire methods of measurement of real components are reviewed

  15. Automotive component failures

    CSIR Research Space (South Africa)

    Heyes, AM

    1998-06-01

    Full Text Available [ However\\ in the presence of a stress concentration the ultimate tensile stress can be exceeded before the ultimate shear stress is reached\\ resulting in a tensile failure 0 [ 2[6[ Metallo`raphy and Ener`y Dispersive Spectroscopy "EDS# A microspecimen...\\ Vol[ 4\\ No[ 1\\ pp[ 018 030\\ 0887 0887 Elsevier Science Ltd[ All rights reserved\\ Pergamon Printed in Great Britain 0249 5296:87 ,08[99 9[99 PII] S0249 5296"87#99909 6 AUTOMOTIVE COMPONENT FAILURES A[ M[ HEYES Advanced Engineering and Testing...

  16. Food Components and Supplements

    DEFF Research Database (Denmark)

    Parlesak, Alexandr

    2012-01-01

    .g., secondary plant metabolites such as flavonoids), or as contaminants that enter the food chain at different stages or during the food production process. For these components, a wide spectrum of biological effects was observed that ranges from health-threatening impacts (e.g., polycyclic aromatic amines...... acting as carcinogens) to health-protective effects (e.g., flavonoids ameliorating detrimental effects of mitochondrial oxidative stress). In particular, secondary plant metabolites along with vitamins, specific types of macronutrients and live bacteria (probiotics) as well as substances promoting...

  17. Mesh Retrieval by Components

    Science.gov (United States)

    Tal, Ayellet; Zuckerberger, Emanuel

    This paper examines the application of the human vision theories of Marr and Biederman to the retrieval of three-dimensional objects. The key idea is to represent an object by an attributed graph that consists of the object's meaningful components as nodes, where each node is fit to a basic shape. A system that realizes this approach was built and tested on a database of about 400 objects and achieves promising results. It is shown that this representation of 3D objects is very compact. Moreover, it gives rise to a retrieval algorithm that is invariant to non-rigid transformations and does not require normalization.

  18. A STATISTICAL APPROACH FOR OBTAINING THE CONTROLLED WOVEN FABRIC WIDTH

    NARCIS (Netherlands)

    Maqsood, Muhammad

    2015-01-01

    A common problem faced in fabric manufacturing is the production of inconsistent fabric width on shuttleless looms in spite of the same fabric specifications. Weft-wise crimp controls the fabric width and it depends on a number of factors, including warp tension, temple type, fabric take-up pressing

  19. Fabrication of microfluidic integrated biosensor

    Science.gov (United States)

    Adam, Tijjani; Dhahi, Th S.; Mohammed, Mohammed; Hashim, U.; Noriman, N. Z.; Dahham, Omar S.

    2017-09-01

    An event of miniaturizing for sensor systems to carry out biological diagnostics are gaining wade spread acceptance. The system may contain several different sensor units for the detection of specific analyte, the analyte to be detected might be any kind of biological molecules (DNA, mRNA or proteins) or chemical substances. In most cases, the detection is based on receptor-ligand binding like DNA hybridization or antibody-antigen interaction, achieving this on a nanostructure. DNA or protein must be attached to certain locations within the structure. Critical for this is to have a robust binding chemistry to the surface in the microstructure. Here we successfully designed and fabricated microfluidics element for passive fluid delivery into polysilicon Nanowire sensing domain, we further demonstrated a very simple and effective way of integrating the two devices to give full functionalities of laboratory on a single chip. The sensing element was successfully surface modified and tested on real biomedical clinical sample for evaluation and validation.

  20. Plastron Respiration Using Commercial Fabrics

    Directory of Open Access Journals (Sweden)

    Shaun Atherton

    2014-01-01

    Full Text Available A variety of insect and arachnid species are able to remain submerged in water indefinitely using plastron respiration. A plastron is a surface-retained film of air produced by surface morphology that acts as an oxygen-carbon dioxide exchange surface. Many highly water repellent and hydrophobic surfaces when placed in water exhibit a silvery sheen which is characteristic of a plastron. In this article, the hydrophobicity of a range of commercially available water repellent fabrics and polymer membranes is investigated, and how the surface of the materials mimics this mechanism of underwater respiration is demonstrated allowing direct extraction of oxygen from oxygenated water. The coverage of the surface with the plastron air layer was measured using confocal microscopy. A zinc/oxygen cell is used to consume oxygen within containers constructed from the different membranes, and the oxygen consumed by the cell is compared to the change in oxygen concentration as measured by an oxygen probe. By comparing the membranes to an air-tight reference sample, it was found that the membranes facilitated oxygen transfer from the water into the container, with the most successful membrane showing a 1.90:1 ratio between the cell oxygen consumption and the change in concentration within the container.

  1. Large superconducting coil fabrication development

    International Nuclear Information System (INIS)

    Brown, R.L.; Allred, E.L.; Anderson, W.C.; Burn, P.B.; Deaderick, R.I.; Henderson, G.M.; Marguerat, E.F.

    1975-01-01

    Toroidal fields for some fusion devices will be produced by an array of large superconducting coils. Their size, space limitation, and field requirements dictate that they be high performance coils. Once installed, accessibility for maintenance and repairs is severely restricted; therefore, good reliability is an obvious necessity. Sufficient coil fabrication will be undertaken to develop and test methods that are reliable, fast, and economical. Industrial participation will be encouraged from the outset to insure smooth transition from development phases to production phases. Initially, practice equipment for three meter bore circular coils will be developed. Oval shape coil forms will be included in the practice facility later. Equipment that is more automated will be developed with the expectation of winding faster and obtaining good coil quality. Alternate types of coil construction, methods of winding and insulating, will be investigated. Handling and assembly problems will be studied. All technology developed must be feasible for scaling up when much larger coils are needed. Experimental power reactors may need coils having six meter or larger bores

  2. Prognostics for Microgrid Components

    Science.gov (United States)

    Saxena, Abhinav

    2012-01-01

    Prognostics is the science of predicting future performance and potential failures based on targeted condition monitoring. Moving away from the traditional reliability centric view, prognostics aims at detecting and quantifying the time to impending failures. This advance warning provides the opportunity to take actions that can preserve uptime, reduce cost of damage, or extend the life of the component. The talk will focus on the concepts and basics of prognostics from the viewpoint of condition-based systems health management. Differences with other techniques used in systems health management and philosophies of prognostics used in other domains will be shown. Examples relevant to micro grid systems and subsystems will be used to illustrate various types of prediction scenarios and the resources it take to set up a desired prognostic system. Specifically, the implementation results for power storage and power semiconductor components will demonstrate specific solution approaches of prognostics. The role of constituent elements of prognostics, such as model, prediction algorithms, failure threshold, run-to-failure data, requirements and specifications, and post-prognostic reasoning will be explained. A discussion on performance evaluation and performance metrics will conclude the technical discussion followed by general comments on open research problems and challenges in prognostics.

  3. Interactions between photodegradation components

    Directory of Open Access Journals (Sweden)

    Abdollahi Yadollah

    2012-09-01

    Full Text Available Abstract Background The interactions of p-cresol photocatalytic degradation components were studied by response surface methodology. The study was designed by central composite design using the irradiation time, pH, the amount of photocatalyst and the p-cresol concentration as variables. The design was performed to obtain photodegradation % as actual responses. The actual responses were fitted with linear, two factor interactions, cubic and quadratic model to select an appropriate model. The selected model was validated by analysis of variance which provided evidences such as high F-value (845.09, very low P-value (2 = 0.999, adjusted R-squared (Radj2 = 0.998, predicted R-squared (Rpred2 = 0.994 and the adequate precision (95.94. Results From the validated model demonstrated that the component had interaction with irradiation time under 180 min of the time while the interaction with pH was above pH 9. Moreover, photocatalyst and p-cresol had interaction at minimal amount of photocatalyst (p-cresol. Conclusion These variables are interdependent and should be simultaneously considered during the photodegradation process, which is one of the advantages of the response surface methodology over the traditional laboratory method.

  4. Towards in process control of polymer micro manufactured components

    DEFF Research Database (Denmark)

    Calaon, Matteo; Tosello, Guido; Hansen, Hans Nørgaard

    2016-01-01

    In the last decade the number of applications of micro components has increased steadily. In order for Europe to maintain its leading role in the polymer micro-fabrication industry there is a need of expansion for processes capabilities for mass manufacture. The present study focuses on the design...... was employed to perform the measurements on the produced polymer parts. Automated measuring routine allowed fast dimensional quality mapping of the functional sub-mm features integrated in the plastic frame of the final microwave component. Design of experiment (DOE) was adopted to quantify significant factors...

  5. Two-component micro injection moulding for hearing aid applications

    DEFF Research Database (Denmark)

    Islam, Aminul; Hansen, Hans Nørgaard; Marhöfer, David Maximilian

    2012-01-01

    Two-component (2k) injection moulding is an important process technique at the present state of technology, and it is growing rapidly in the field of precision micro moulding. Besides combining different material properties in the same product, two-component moulding can eliminate many assembly...... parts. An intensive search for suitable 2k materials is made and few combinations of plastic materials are presented in the paper which can be used for highly demanding application areas like hearing aids. By using these material combinations, a demonstrator 2k micro part has been fabricated...

  6. Structural evaluation of safety class components to natural phenomena loadings

    International Nuclear Information System (INIS)

    Conrads, T.J.

    1989-01-01

    This paper addresses the efforts completed at the US Department of Energy Hanford Site near Richland, Washington, to qualify structurally a number of existing safety class components in the Plutonium Finishing Plant complex. Design, fabrication, and installation of the facility occurred in the 1950s and 1960s and were based on the Uniform Building Code criteria for wind and earthquake loads. Recently the buildings were qualified to site-specific wind and seismic hazards. The methodology employed to qualify seismically the safety class components is discussed

  7. Passive RF component technology materials, techniques, and applications

    CERN Document Server

    Wang, Guoan

    2012-01-01

    Focusing on novel materials and techniques, this pioneering volume provides you with a solid understanding of the design and fabrication of smart RF passive components. You find comprehensive details on LCP, metal materials, ferrite materials, nano materials, high aspect ratio enabled materials, green materials for RFID, and silicon micromachining techniques. Moreover, this practical book offers expert guidance on how to apply these materials and techniques to design a wide range of cutting-edge RF passive components, from MEMS switch based tunable passives and 3D passives, to metamaterial-bas

  8. Chondrites and their Components

    Science.gov (United States)

    Scott, E. R. D.; Krot, A. N.

    2003-12-01

    What are Chondrites?Chondrites are meteorites that provide the best% clues to the origin of the solar system. They are the oldest known rocks - their components formed during the birth of the solar system ca. 4,567 Ma - and their abundances of nonvolatile elements are close to those in the solar photosphere. Chondrites are broadly ultramafic in composition, consisting largely of iron, magnesium, silicon, and oxygen. The most abundant constituents of chondrites are chondrules, which are igneous particles that crystallized rapidly in minutes to hours. They are composed largely of olivine and pyroxene, commonly contain metallic Fe,Ni and are 0.01-10 mm in size. Some chondrules are rounded as they were once entirely molten but many are irregular in shape because they were only partly melted or because they accreted other particles as they solidified. Chondrites themselves were never molten. The definition of a chondrite has expanded recently with the discovery in Antarctica and the Sahara Desert of extraordinary meteorites with chondrules 10-100 μm in size, and chondrites so rich in metallic Fe,Ni that they were initially classified as iron meteorites with silicate inclusions. Thus, in meteoritics, as in other fields of planetary science, new discoveries sometimes require definitions to be modified.Chondrites are so diverse in their mineralogical and textural characteristics that it is not possible to describe a typical chondrite. We show one with diversely textured chondrules including prominent, aesthetically pleasing, rounded chondrules (Figure 1(a)), and another with more uniformly textured chondrules (Figure 1(b)). Owing to the high abundance of rounded or droplet chondrules in the abundant, so-called "ordinary" chondrites ( Figure 1(a)), studies of the origin of chondrules have commonly been based on these chondrites. (7K)Figure 1. Maps showing magnesium concentrations in two chondrites: (a) PCA91082, a CR2 carbonaceous chondrite, and (b) Tieschitz, an H/L3

  9. Computer Optimization of Biodegradable Nanoparticles Fabricated by Dispersion Polymerization

    Directory of Open Access Journals (Sweden)

    Emmanuel O. Akala

    2015-12-01

    Full Text Available Quality by design (QbD in the pharmaceutical industry involves designing and developing drug formulations and manufacturing processes which ensure predefined drug product specifications. QbD helps to understand how process and formulation variables affect product characteristics and subsequent optimization of these variables vis-à-vis final specifications. Statistical design of experiments (DoE identifies important parameters in a pharmaceutical dosage form design followed by optimizing the parameters with respect to certain specifications. DoE establishes in mathematical form the relationships between critical process parameters together with critical material attributes and critical quality attributes. We focused on the fabrication of biodegradable nanoparticles by dispersion polymerization. Aided by a statistical software, d-optimal mixture design was used to vary the components (crosslinker, initiator, stabilizer, and macromonomers to obtain twenty nanoparticle formulations (PLLA-based nanoparticles and thirty formulations (poly-ɛ-caprolactone-based nanoparticles. Scheffe polynomial models were generated to predict particle size (nm, zeta potential, and yield (% as functions of the composition of the formulations. Simultaneous optimizations were carried out on the response variables. Solutions were returned from simultaneous optimization of the response variables for component combinations to (1 minimize nanoparticle size; (2 maximize the surface negative zeta potential; and (3 maximize percent yield to make the nanoparticle fabrication an economic proposition.

  10. Computer Optimization of Biodegradable Nanoparticles Fabricated by Dispersion Polymerization.

    Science.gov (United States)

    Akala, Emmanuel O; Adesina, Simeon; Ogunwuyi, Oluwaseun

    2015-12-22

    Quality by design (QbD) in the pharmaceutical industry involves designing and developing drug formulations and manufacturing processes which ensure predefined drug product specifications. QbD helps to understand how process and formulation variables affect product characteristics and subsequent optimization of these variables vis-à-vis final specifications. Statistical design of experiments (DoE) identifies important parameters in a pharmaceutical dosage form design followed by optimizing the parameters with respect to certain specifications. DoE establishes in mathematical form the relationships between critical process parameters together with critical material attributes and critical quality attributes. We focused on the fabrication of biodegradable nanoparticles by dispersion polymerization. Aided by a statistical software, d-optimal mixture design was used to vary the components (crosslinker, initiator, stabilizer, and macromonomers) to obtain twenty nanoparticle formulations (PLLA-based nanoparticles) and thirty formulations (poly-ɛ-caprolactone-based nanoparticles). Scheffe polynomial models were generated to predict particle size (nm), zeta potential, and yield (%) as functions of the composition of the formulations. Simultaneous optimizations were carried out on the response variables. Solutions were returned from simultaneous optimization of the response variables for component combinations to (1) minimize nanoparticle size; (2) maximize the surface negative zeta potential; and (3) maximize percent yield to make the nanoparticle fabrication an economic proposition.

  11. Computer Optimization of Biodegradable Nanoparticles Fabricated by Dispersion Polymerization

    Science.gov (United States)

    Akala, Emmanuel O.; Adesina, Simeon; Ogunwuyi, Oluwaseun

    2015-01-01

    Quality by design (QbD) in the pharmaceutical industry involves designing and developing drug formulations and manufacturing processes which ensure predefined drug product specifications. QbD helps to understand how process and formulation variables affect product characteristics and subsequent optimization of these variables vis-à-vis final specifications. Statistical design of experiments (DoE) identifies important parameters in a pharmaceutical dosage form design followed by optimizing the parameters with respect to certain specifications. DoE establishes in mathematical form the relationships between critical process parameters together with critical material attributes and critical quality attributes. We focused on the fabrication of biodegradable nanoparticles by dispersion polymerization. Aided by a statistical software, d-optimal mixture design was used to vary the components (crosslinker, initiator, stabilizer, and macromonomers) to obtain twenty nanoparticle formulations (PLLA-based nanoparticles) and thirty formulations (poly-ɛ-caprolactone-based nanoparticles). Scheffe polynomial models were generated to predict particle size (nm), zeta potential, and yield (%) as functions of the composition of the formulations. Simultaneous optimizations were carried out on the response variables. Solutions were returned from simultaneous optimization of the response variables for component combinations to (1) minimize nanoparticle size; (2) maximize the surface negative zeta potential; and (3) maximize percent yield to make the nanoparticle fabrication an economic proposition. PMID:26703678

  12. Fabrication Control Plan for ORNL RH-LOCA ATF Test Specimens to be Irradiated in the ATR

    Energy Technology Data Exchange (ETDEWEB)

    Field, Kevin G. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Howard, Richard [Idaho National Lab. (INL), Idaho Falls, ID (United States); Teague, Michael [Idaho National Lab. (INL), Idaho Falls, ID (United States)

    2014-06-01

    The purpose of this fabrication plan is (1) to summarize the design of a set of rodlets that will be fabricated and then irradiated in the Advanced Test Reactor (ATR) and (2) provide requirements for fabrication and acceptance criteria for inspections of the Light Water Reactor (LWR) – Accident Tolerant Fuels (ATF) rodlet components. The functional and operational (F&OR) requirements for the ATF program are identified in the ATF Test Plan. The scope of this document only covers fabrication and inspections of rodlet components detailed in drawings 604496 and 604497. It does not cover the assembly of these items to form a completed test irradiation assembly or the inspection of the final assembly, which will be included in a separate INL final test assembly specification/inspection document. The controls support the requirements that the test irradiations must be performed safely and that subsequent examinations must provide valid results.

  13. Advanced Manufacturing of an Aircraft Component (Fish-Head): A Technology Review on the Fabrication

    OpenAIRE

    M. Minhat; S. B. Mohamed; M. S. Kasim; M. A. Sulaiman; Zairi Ismael Rizman

    2016-01-01

    The Airbus fish-head is machined using a 5-axis Computerized Numerical Control (CNC) milling machine, which consists of many complex shapes that are built into it. A conventional CNC machining requires tremendous effort in programming and investment due to the increasing in features complexity of the fish-head to be machined. An alternative method through advanced manufacturing processes namely vacuum casting, Fused Deposition Modelling (FDM) and three dimensional printing (3DP) is reviewed. ...

  14. Fabrication and component testing results for a Nb3Sn dipole magnet

    International Nuclear Information System (INIS)

    Dell'Orco, D.; Scanlan, R.M.; Taylor, C.E.; Lietzke, A.; Caspi, S.; van Oort, J.M.; McInturff, A.D.

    1994-10-01

    At present, the maximum field achieved in accelerator R ampersand D dipoles is slightly over 10T, with NbTi conductor at 1.8 K. Although Nb 3 Sn has the potential to achieve much higher fields, none of the previous dipoles constructed from Nb 3 Sn have broken the 10T barrier. We report here on the construction of a dipole with high current density Nb 3 Sn with a predicted short sample limit of 13T. A wind and react technique, followed by epoxy impregnation of the fiberglass insulated coils, was used. The problems identified with the use of Nb 3 SD in earlier dipole magnets were investigated in a series of supplemental tests. This includes measurement of the degradation of J c with transverse strain, cabling degradation, joint resistance measurements, and epoxy strength tests. In addition, coff assembly techniques were developed to ensure that adequate prestress could be applied without damaging the reacted Nb 3 Sn cable. We report here the results of these tests and the construction status of this 50 mm bore dipole

  15. Design and fabrication of HTTR components by Kawasaki Heavy Industries, LTD

    International Nuclear Information System (INIS)

    Nomura, Youichi; Katsuki, Taketsugu; Satou, Kouji

    2000-01-01

    Developed by Japan Atomic Energy Research Institute, HTTR reached the critical point for the first time, on 10th of November 1998, and is now under examination for raising power to 100% operation. Kawasaki Heavy Industries, LTD has been engaged in construction of HTTR, in charge of designing and manufacturing of various facilities. We are taking this opportunity to review our designing and manufacturing of facilities, in the FAPIG magazine. (author)

  16. Mathematical and Computational Framework for Virtual Fabrication Environment for Aircraft Components

    National Research Council Canada - National Science Library

    Szabo, Barna A

    2008-01-01

    ... so that they can serve as reliable and accurate representations of physical reality in the sense that they will provide predictions of events or states of systems that can be confirmed consistently by physical observations...

  17. Process chain for fabrication of anisotropic optical functional surfaces on polymer components

    DEFF Research Database (Denmark)

    Li, Dongya; Zhang, Yang; Regi, Francesco

    2017-01-01

    from a certain viewing angle. The process chain comprised three steps: tooling, replicationand quality assurance. Tooling was achieved by precision micro milling. Replication processes such as injection moulding, hotembossing, blow moulding, etc. were employed according to the specific type of product...

  18. 19 CFR 10.14 - Fabricated components subject to the exemption.

    Science.gov (United States)

    2010-04-01

    ....14 Section 10.14 Customs Duties U.S. CUSTOMS AND BORDER PROTECTION, DEPARTMENT OF HOMELAND SECURITY... of various type, electrical conductors, metal foils, insulating tapes, ribbons, findings used in... assembly for a computer is assembled in the United States by soldering American-made and foreign-made...

  19. Fabrication of mechanical components and piping design for Brazilian nuclear reactors

    International Nuclear Information System (INIS)

    Deppe, L.O.

    1987-01-01

    The supply of Brazilian equipment and piping design for Angra 2 (and Angra 3 in some cases) have reached an advanced status in spite of the continuous outside difficulties which affect these nuclear power plants. The achieved quality is similar to the quality achieved in foreign countries and the nationalization program foreseen in 1975 is being largely surpassed. In this paper the actual situation is presented as well as the future perspectives. (Author) [pt

  20. Fibre, yarn and fabric properties of the Cashmere component of South African indigenous goat hair

    CSIR Research Space (South Africa)

    Botha, Anton F

    2008-11-01

    Full Text Available on studies undertaken to determine the ability of South African indigenous goats to produce cashmere-like fibres and presents some of the results obtained on fleece samples tested during the past 10 years. Reference is made to the fibre quality, yield...

  1. Fibre, yarn and fabric properties of the Cashmere component of South African indigenous goat hair.

    CSIR Research Space (South Africa)

    Botha, Anton F

    2008-11-01

    Full Text Available South Africa has over 4 million indigenous goats (Boer, Savannah and Nguni/Mbusi breeds), many of which have two coats of fibre, namely a cashmere-like fine down and a coarse guard hair. These goats are primarily kept for their meat, milk and skin...

  2. Heat Transfer in Directional Water Transport Fabrics

    Directory of Open Access Journals (Sweden)

    Chao Zeng

    2016-10-01

    Full Text Available Directional water transport fabrics can proactively transfer moisture from the body. They show great potential in making sportswear and summer clothing. While moisture transfer has been previously reported, heat transfer in directional water transport fabrics has been little reported in research literature. In this study, a directional water transport fabric was prepared using an electrospraying technique and its heat transfer properties under dry and wet states were evaluated, and compared with untreated control fabric and the one pre-treated with NaOH. All the fabric samples showed similar heat transfer features in the dry state, and the equilibrium temperature in the dry state was higher than for the wet state. Wetting considerably enhanced the thermal conductivity of the fabrics. Our studies indicate that directional water transport treatment assists in moving water toward one side of the fabric, but has little effect on thermal transfer performance. This study may be useful for development of “smart” textiles for various applications.

  3. Component Based Testing with ioco

    NARCIS (Netherlands)

    van der Bijl, H.M.; Rensink, Arend; Tretmans, G.J.

    Component based testing concerns the integration of components which have already been tested separately. We show that, with certain restrictions, the ioco-test theory for conformance testing is suitable for component based testing, in the sense that the integration of fully conformant components is

  4. Component Composition Using Feature Models

    DEFF Research Database (Denmark)

    Eichberg, Michael; Klose, Karl; Mitschke, Ralf

    2010-01-01

    In general, components provide and require services and two components are bound if the first component provides a service required by the second component. However, certain variability in services - w.r.t. how and which functionality is provided or required - cannot be described using standard i...

  5. Powder Injection Molding of Ceramic Engine Components for Transportation

    Science.gov (United States)

    Lenz, Juergen; Enneti, Ravi K.; Onbattuvelli, Valmikanathan; Kate, Kunal; Martin, Renee; Atre, Sundar

    2012-03-01

    Silicon nitride has been the favored material for manufacturing high-efficiency engine components for transportation due to its high temperature stability, good wear resistance, excellent corrosion resistance, thermal shock resistance, and low density. The use of silicon nitride in engine components greatly depends on the ability to fabricate near net-shape components economically. The absence of a material database for design and simulation has further restricted the engineering community in developing parts from silicon nitride. In this paper, the design and manufacturability of silicon nitride engine rotors for unmanned aerial vehicles by the injection molding process are discussed. The feedstock material property data obtained from experiments were used to simulate the flow of the material during injection molding. The areas susceptible to the formation of defects during the injection molding process of the engine component were identified from the simulations. A test sample was successfully injection molded using the feedstock and sintered to 99% density without formation of significant observable defects.

  6. FIBROUS MONOLITH WEAR RESISTANT COMPONENTS FOR THE MINING INDUSTRY

    Energy Technology Data Exchange (ETDEWEB)

    Mike L. Fulcher; Kenneth L. Knittel

    2004-06-08

    The work performed on this program was to develop wear resistant, tough FM composite materials with efforts focused on WC-Co based FM systems. The materials were developed for use in mining industry wear applications. Components of interest were drill bit inserts for drilling blast holes. Other component applications investigated included wear plates for a variety of equipment such as pit shovels, wear surfaces for conveyors, milling media for ball milling operations, hydrocyclone cones, grader blades and dozer teeth. Cross-cutting technologies investigated included hot metal extrusion dies, drill bits for circuit board fabrication, cutting tools for cast iron and aluminum machining. An important part of the work was identification of the standard materials used in drilling applications. A materials trade study to determine those metals and ceramics used for mining applications provided guidance for the most important materials to be investigated. WC-Co and diamond combinations were shown to have the most desirable properties. Other considerations such as fabrication technique and the ability to consolidate shifted the focus away from diamond materials and toward WC-Co. Cooperating partners such as Kennametal and Kyocera assisted with supplies, evaluations of material systems, fabricated parts and suggestions for cross-cutting technology applications for FM architectures. Kennametal provided the raw materials (WC-Co and Al-TiCN powders) for the extent of the material evaluations. Kyocera shared their research into various FM systems and provided laboratory testing of fabricated materials. Field testing provided by partners Superior Rock Bit and Brady Mining and Construction provided insight into the performance of the fabricated materials under actual operational conditions. Additional field testing of cross-cutting technology, the extrusion of hot metals, at Extruded Metals showed the potential for additional market development.

  7. Component failure data handbook

    International Nuclear Information System (INIS)

    Gentillon, C.D.

    1991-04-01

    This report presents generic component failure rates that are used in reliability and risk studies of commercial nuclear power plants. The rates are computed using plant-specific data from published probabilistic risk assessments supplemented by selected other sources. Each data source is described. For rates with four or more separate estimates among the sources, plots show the data that are combined. The method for combining data from different sources is presented. The resulting aggregated rates are listed with upper bounds that reflect the variability observed in each rate across the nuclear power plant industry. Thus, the rates are generic. Both per hour and per demand rates are included. They may be used for screening in risk assessments or for forming distributions to be updated with plant-specific data

  8. Impedance and component heating

    CERN Document Server

    Métral, E; Mounet, N; Pieloni, T; Salvant, B

    2015-01-01

    The impedance is a complex function of frequency, which represents, for the plane under consideration (longitudinal, horizontal or vertical), the force integrated over the length of an element, from a “source” to a “test” wave, normalized by their charges. In general, the impedance in a given plane is a nonlinear function of the test and source transverse coordinates, but it is most of the time sufficient to consider only the first few linear terms. Impedances can influence the motion of trailing particles, in the longitudinal and in one or both transverse directions, leading to energy loss, beam instabilities, or producing undesirable secondary effects such as excessive heating of sensitive components at or near the chamber wall, called beam-induced RF heating. The LHC performance limitations linked to impedances encountered during the 2010-2012 run are reviewed and the currently expected situation during the HL-LHC era is discussed.

  9. Food Components and Supplements

    DEFF Research Database (Denmark)

    Parlesak, Alexandr

    2012-01-01

    The major part of food consists of chemical compounds that can be used for energy production, biological synthesis, or maintenance of metabolic processes by the host. These components are defined as nutrients, and can be categorized into macronutrients (proteins, carbohydrates, triglycerides......, and alcohol), minerals, and micronutrients. The latter category comprises 13 vitamins and a hand full of trace elements. Many micronutrients are used as food supplements and are ingested at doses exceeding the amounts that can be consumed along with food by a factor of 10–100. Both macro- and micronutrients...... can interact with enzyme systems related to xenobiotic metabolism either by regulation of their expression or direct interference with their enzymatic activity. During food consumption, we consume a wide range of xenobiotics along with the consumable food, either as an original part of the food (e...

  10. High thermal load component

    International Nuclear Information System (INIS)

    Fuse, Toshiaki; Tachikawa, Nobuo.

    1996-01-01

    A cooling tube made of a pure copper is connected to the inner portion of an armour (heat resistant member) made of an anisotropic carbon/carbon composite (CFC) material. The CFC material has a high heat conductivity in longitudinal direction of fibers and has low conductivity in perpendicular thereto. Fibers extending in the armour from a heat receiving surface just above the cooling tube are directly connected to the cooling tube. A portion of the fibers extending from a heat receiving surface other than portions not just above the cooling tube is directly bonded to the cooling tube. Remaining fibers are disposed so as to surround the cooling tube. The armour and the cooling tube are soldered using an active metal flux. With such procedures, high thermal load components for use in a thermonuclear reactor are formed, which are excellent in a heat removing characteristic and hardly causes defects such as crackings and peeling. (I.N.)

  11. Autonomous component carrier selection

    DEFF Research Database (Denmark)

    Garcia, Luis Guilherme Uzeda; Pedersen, Klaus; Mogensen, Preben

    2009-01-01

    management and efficient system operation. Due to the expected large number of user-deployed cells, centralized network planning becomes unpractical and new scalable alternatives must be sought. In this article, we propose a fully distributed and scalable solution to the interference management problem......Low-power base stations such as e.g. Femto-cells are one of the candidates for high data rate provisioning in local areas, such as residences, apartment complexes, business offices and outdoor hotspot scenarios. Unfortunately, the benefits are not without new challenges in terms of interference...... in local areas, basing our study case on LTE-Advanced. We present extensive network simulation results to demonstrate that a simple and robust interference management scheme, called autonomous component carrier selection allows each cell to select the most attractive frequency configuration; improving...

  12. Solar bowl component efficiencies

    International Nuclear Information System (INIS)

    O'Hair, E.A.; Green, B.L.

    1992-01-01

    Battelle Pacific Northwest Laboratory has published two volumes on the economic evaluation of various proposed configurations and plant sizes for the four solar thermal technologies. These are the latest in a series of publications sponsored by the Department of Energy (DOE) on plant and operational costs and are more complete in that they include calculations of electrical output. These latest Battelle volumes use the 1976 solar data from Barstow, Calif., and by calculating or estimating the energy conversion efficiency of each element in the process from sun to electricity predict the output and cost of electricity from different plant sizes for each of the four technologies. In this paper a comparison is presented of the component efficiencies developed by Battelle and those of the solar bowl at Crosbyton, Tex

  13. The fabrication of andean particularism

    Directory of Open Access Journals (Sweden)

    1989-01-01

    Full Text Available Ce travail aborde la question des liens que la société coloniale garde avec son passé. Plutôt que de concevoir cette relation en termes de survie d'une culture indigène authentique à travers le canal de la résistance, l'auteur met l'accent sur la fabrication de la tradition au sein de l'appareil étatique du régime colonial et montre comment la résistance politique tournée vers le passé réutilise cette tradition. Cette recherche part de l'étude de cas que présente un incident peu connu dans les Andes du nord, lié au 'culte à l'Inca' et survenu dans l'Audience de Quito, au XVIIème siècle. Un tel objet d'étude semble fort riche d'enseignements et nous laisse entrevoir le rapport existant entre l'autorité et la tradition, car il met en lumière les mécanismes de remémoration, conservation et de récupération du passé. Este trabajo aborda la problemática de la relación que la sociedad colonial mantiene con su pasado. En vez de concebir esta relación a través de la figura de la conservación de la cultura andina por la vía de la resistencia, enfoca la fabricación de la tradición (de la memoria y de las costumbres en el seno de los aparatos estatales del régimen colonial. Muestra como la resistencia política orientada hacia el pasado reutiliza la tradición inventada dentro de los dispositivos disciplinarios. La discusión de estos temas se lleva a cabo en base a un estudio de caso de un incidente del culto al Inca y de resistencia enfocada en el simbolismo del Inca, que tuvo lugar en la Audiencia de Quito a mediados del siglo diecisiete. La invocación del Inca en la época colonial ofrece un campo privilegiado para examinar la relación entre la autoridad y los orígenes, ya que implica la conmemoración, continuación y recuperación del pasado. This paper addresses the issue of the relationship that the colonial order keeps with its past. Instead of conceiving this relation in terms of the preservation of an

  14. Toward an Active Fabric-Based Air Decontamination System

    National Research Council Canada - National Science Library

    Gaddy, G. A; Bratcher, Matthew S; Mills, G; Huang, S; Slaten, B. L; Debortoli, J

    2004-01-01

    ...) particles that were grafted on cotton fabric and on TiO2 particles that were embedded in glass fabric Modified TiO2 particles were grafted onto cotton fabric and irradiated in the presence of CHCl3...

  15. Progress on KMRR fuel fabrication

    International Nuclear Information System (INIS)

    Kuk, I.H.; Lee, J.B.; Rhee, C.K.; Kim, K.W.

    1991-01-01

    In order to increase the practical applicability of powder heat-treatment in KMRR fuel fabrication, efforts were made to reduce the critical size. Primary U 3 Si 2 particle size was reviewed in terms of cooling rate. Temperature dependence of peritectoid reaction was reviewed as well. (1) Cooling rate of U 3 Si molten alloy was calculated by ADINA program. In practice, particle size of the primary U 3 Si 2 varies radially. U 3 Si 2 size increases as it goes deeper from the surface. As cooling rate increases, primary U 3 Si 2 size decreases. (2) Peritectoid reaction occurs in two unique groups of temperature; one is below 790 C where β-U and U 3 Si 2 reaction occurs, and the other above 790 C where γ-U and U 3 Si 2 reaction occurs. 780 C is most completely reacting temperature in β-U region, and 810 C is so in γ-U region. Reaction is completed more perfectly in γ-U region than in β-U region. 810 C is found to be the optimized heat-treatment temperature, but it is desirable not to approach to 790 C in heat-treatment. (3) The critical powder size in powder heat-treatment is dependent on the primary U 3 Si 2 particle size. The smaller the primary U 3 Si 2 particle size, the smaller the critical particle size of the powder. At present, the primary U 3 Si 2 particle size can be reduced to 3∝5 μm at 4∝5 mm deep from surface in Cu mold. This may be reduced further by rapid solidification process. (orig.)

  16. Silicon fabric for multi-functional applications

    KAUST Repository

    Sevilla, Galo T.

    2013-06-01

    This paper reports a generic process flow to fabricate mechanically flexible and optically semi-transparent thermoelectric generators (TEGs), micro lithium-ion batteries (μLIB) and metal-oxide-semiconductor capacitors (MOSCAPs) on mono-crystalline silicon fabric platforms from standard bulk silicon (100) wafers. All the fabricated devices show outstanding mechanical flexibility and performance, making an important step towards monolithic integration of Energy Chip (self-powered devices) including energy harvesters and electronic devices on flexible platforms. We also report a recyclability process for the remaining bulk substrate after release, allowing us to achieve a low cost flexible platform for high performance applications. © 2013 IEEE.

  17. UPDATE ON MONOLITHIC FUEL FABRICATION METHODS

    Energy Technology Data Exchange (ETDEWEB)

    C. R. Clark; J. F. Jue; G. A. Moore; N. P. Hallinan; B. H. Park; D. E. Burkes

    2006-10-01

    Efforts to develop a viable monolithic research reactor fuel plate have continued at Idaho National Laboratory. These efforts have concentrated on both fabrication process refinement and scale-up to produce full sized fuel plates. Progress at INL has led to fabrication of hot isostatic pressed uranium-molybdenum bearing monolithic fuel plates. These miniplates are part of the RERTR-8 miniplate irradiation test. Further progress has also been made on friction stir weld processing which has been used to fabricate full size fuel plates which will be irradiated in the ATR and OSIRIS reactors.

  18. Design, fabrication and installation of irradiation facilities

    Energy Technology Data Exchange (ETDEWEB)

    Sim, Bong Shick; Kim, Y. S.; Lee, C. Y. and others

    1999-03-01

    The principal contents of this project are to design, fabricate and install the steady-state fuel test loop in HANARO for nuclear technology development. Procurement and fabrication of main equipment, licensing and technical review for fuel test loop have been performed during 2 years(1997, 1998) for this project. Following contents are described in the report. - Procurement and fabrication of the equipment, piping for OPS - IPS manufacture - License - Technical review and evaluation of the FTL facility. As besides, as these irradiation facilities will be installed in HANARO, review of safety concern, discussion with KINS for licensing and review ofHANARO interface have been performed respectively. (author)

  19. Confidence regions for fabric shape diagrams

    Science.gov (United States)

    Ringrose, Trevor J.; Benn, Douglas I.

    1997-12-01

    Fabric shape is often quantified using the three eigenvalues from the 'orientation tensor' method applied to a sample of directions. Several studies have used eigenvalues plotted on fabric shape diagrams to distinguish sedimentary facies or strain histories. However, such studies seldom consider how well the sample eigenvalues represent the true fabric shape. In this paper, we use 'bootstrapping' techniques to define confidence regions for sample eigenvalues, and show that sample and population eigenvalues may differ substantially. Confidence regions are often very large for small sample sizes, and we recommend that sample sizes should be at least 50.

  20. Thermoplastic microcantilevers fabricated by nanoimprint lithography

    DEFF Research Database (Denmark)

    Greve, Anders; Keller, Stephan Urs; Vig, Asger Laurberg

    2010-01-01

    Nanoimprint lithography has been exploited to fabricate micrometre-sized cantilevers in thermoplastic. This technique allows for very well defined microcantilevers and gives the possibility of embedding structures into the cantilever surface. The microcantilevers are fabricated in TOPAS and are up...... to 500 μm long, 100 μm wide, and 4.5 μm thick. Some of the cantilevers have built-in ripple surface structures with heights of 800 nm and pitches of 4 μm. The yield for the cantilever fabrication is 95% and the initial out-of-plane bending is below 10 μm. The stiffness of the cantilevers is measured...

  1. Fabricating solid carbon porous electrodes from powders

    Science.gov (United States)

    Kaschmitter, James L.; Tran, Tri D.; Feikert, John H.; Mayer, Steven T.

    1997-01-01

    Fabrication of conductive solid porous carbon electrodes for use in batteries, double layer capacitors, fuel cells, capacitive dionization, and waste treatment. Electrodes fabricated from low surface area (Electrodes having a higher surface area, fabricated from powdered carbon blacks, such as carbon aerogel powder, carbon aerogel microspheres, activated carbons, etc. yield high conductivity carbon compositives with excellent double layer capacity, and can be used in double layer capacitors, or for capacitive deionization and/or waste treatment of liquid streams. By adding metallic catalysts to be high surface area carbons, fuel cell electrodes can be produced.

  2. Fabrication of biopolymer cantilevers using nanoimprint lithography

    DEFF Research Database (Denmark)

    Keller, Stephan Sylvest; Feidenhans'l, Nikolaj Agentoft; Fisker-Bødker, Nis

    2011-01-01

    The biodegradable polymer poly(l-lactide) (PLLA) was introduced for the fabrication of micromechanical devices. For this purpose, thin biopolymer films with thickness around 10 μm were spin-coated on silicon substrates. Patterning of microcantilevers is achieved by nanoimprint lithography. A major...... challenge was the high adhesion between PLLA and silicon stamp. Optimized stamp fabrication and the deposition of a 125 nm thick fluorocarbon anti-stiction coating on the PLLA allowed the fabrication of biopolymer cantilevers. Resonance frequency measurements were used to estimate the Young’s modulus...

  3. Fabrication and Multiprobe Electrical Characterization of Nanostructures

    DEFF Research Database (Denmark)

    Klarskov, Mikkel Buster

    2013-01-01

    Engineering of graphene for modifying electrical properties, such as opening an electronic band gap, has been shown both theoretically and experimentally by creating periodic holes in the graphene sheet, however at the price of lower carrier mobility. Such holes can be made with special fabrication...... techniques, such as colloidal lithography or block copolymers lithography, which covers the entire sample. This project presents graphene devices with periodic holes fabricated by electron beam lithography. Only partial coverage of holes are fabricated by making from one to many rows of holes perpendicular...

  4. Deep x-ray lithography processing for batch fabrication of thick polymer-based antenna structures

    Science.gov (United States)

    Rashidian, Atabak; Klymyshyn, David M.; Boerner, Martin; Mohr, Jürgen

    2010-02-01

    Deep x-ray lithography is applied for the first time to fabricate polymer-based antenna structures with different portions of ceramic contents. To produce successful and viable antenna structures, three different methods are proposed using positive and negative tone resists. In the first method the structures are lithographically fabricated avoiding an intermediate molding step using SU-8 as a photosensitive resist filled with fine ceramic powder with particles in the submicron range. In the second and third methods a polymethylmethacrylate (PMMA) mold is first fabricated by x-ray lithography, and then SU-8/MMA mixed with the high ceramic powder content is injected into the mold. In these methods a final step of crosslinking for SU-8 and polymerization for MMA is also required. Optimized fabrication parameters allow the production of high quality antenna structures as thick as 2.3 mm. X-ray lithography capabilities in fabrication of antennas and other passive microwave components with special features reinforce the idea of fabricating integrated passive microwave circuits along with active circuits using this emerging technology.

  5. Optimum processing parameters for the fabrication of twill flax fabric-reinforced polypropylene (PP) composites

    Science.gov (United States)

    Zuhudi, Nurul Zuhairah Mahmud; Minhat, Mulia; Shamsuddin, Mohd Hafizi; Isa, Mohd Dali; Nur, Nurhayati Mohd

    2017-12-01

    In recent years, natural fabric thermoplastic composites such as flax have received much attention due to its attractive capabilities for structural applications. It is crucial to study the processing of flax fabric materials in order to achieve good quality and cost-effectiveness in fibre reinforced composites. Though flax fabric has been widely utilized for several years in composite applications due to its high strength and abundance in nature, much work has been concentrated on short flax fibre and very little work focused on using flax fabric. The effectiveness of the flax fabric is expected to give higher strength performance due to its structure but the processing needs to be optimised. Flax fabric composites were fabricated using compression moulding due to its simplicity, gives good surface finish and relatively low cost in terms of labour and production. Further, the impregnation of the polymer into the fabric is easier in this process. As the fabric weave structure contributes to the impregnation quality which leads to the overall performance, the processing parameters of consolidation i.e. pressure, time, and weight fraction of fabric were optimized using the Taguchi method. This optimization enhances the consolidation quality of the composite by improving the composite mechanical properties, three main tests were conducted i.e. tensile, flexural and impact test. It is observed that the processing parameter significantly affected the consolidation and quality of composite.

  6. Fabric Reconstruction Based on Sustainable Development: Take the Type of Fabric Recycling as an Example

    Directory of Open Access Journals (Sweden)

    Zhangting Guan

    2017-07-01

    Full Text Available Sustainable development is a very important concept of our time, it wants to do is to live in harmony with people, to protect the environment where our human survival. Fabric recycling refers to the use of a variety of traditional and high-tech means of the existing fabric fabric design and processing. So that the surface of a rich visual texture and tactile texture "through the fabric recycling approach. However, the fabric form and clothing design coordination between the clothing design is essential to the link! Garment fabric is not only the material basis of clothing modeling But also an important form of plastic arts. Fabric recycling art has gradually become a new breakthrough point of fashion design! And become an important means to increase the added value of clothing products. But at the same time fabric recycling also follow the concept of sustainable development. This paper analyzes the relationship between fabric reengineering and sustainable development. Combined with practice to explore the fabric processing technology and its creative ideas and some of its environmental performance.

  7. Lab on a fabric: Mass producible and low-cost fabric filters for the high-throughput viable isolation of circulating tumor cells.

    Science.gov (United States)

    Bu, Jiyoon; Kang, Yoon-Tae; Lee, Yong-Seok; Kim, Jeongsuk; Cho, Young-Ho; Moon, Byung-In

    2017-05-15

    Circulating tumor cells (CTCs) play an important role in estimating the presence and the metastatic relapse of tumor. Despite of their importance, isolation of viable CTCs is still struggling, since chemical or mechanical damages are unavoidable when separating less than 1000 of CTCs out of billions of other blood components. Furthermore, the current CTC isolation devices show low productivity, since they are produced after a series of complicated fabrication processes. Here, we present a low-cost and mass-producible fabric filters for the viable CTC isolation and the further molecular assay for profiling cancer-associated markers. The fabric filter, produced by polyester monofilament yarns, can be massively produced at extremely low-cost, by showing productivity of ~22filters/s at ~59filters/USD. By utilizing size-based sorting method, the fabric filter is capable to isolate both epithelial and mesenchymal CTCs, while slots with curved walls are beneficial for preventing the cell rupture by reducing 21.6% of mechanical stress compared to the conventional straight-walled slots. We applied our filter to 11 human blood samples and found that the number of CTCs was closely related to the expression level of Ki-67, which is highly overexpressed in proliferative tumors. The fabric filter might be an appropriate caner-screening tool in developing countries, where people suffer from insufficient healthcare services. Copyright © 2017 Elsevier B.V. All rights reserved.

  8. DESIGN AND FABRICATION OF THE BEAM POSITION MONITOR FOR THE PEFP LINAC

    Directory of Open Access Journals (Sweden)

    HYEOK-JUNG KWON

    2013-08-01

    Full Text Available The beam position monitor (BPM is an essential component for the PEFP 100-MeV linac's commissioning. A prototype stripline-type linac BPM was designed for this purpose. The electrode aperture is 20 mm in diameter, and the electrode is 25 mm long, so it can be installed between Drift Tube Linac (DTL101 and DTL102, which is the shortest distance. One end of the electrode is connected to the Sub Miniature Type A (SMA feed through for signal measurement, and the other end is terminated as a short. The signal amplitude of the fundamental component was calculated and compared with that of the second harmonic component. The designed BPM was fabricated and a low-power RF test was conducted. In this paper, the design, fabrication and low power test of the BPM for the PEFP linac are presented.

  9. Impediments for Digital Fabrication in Education

    DEFF Research Database (Denmark)

    Smith, Rachel Charlotte; Iversen, Ole Sejer; Veerasawmy, Rune

    2016-01-01

    of technology and design is largely absent. The paper addresses the experiences and challenges that digital fabrication technology present for teachers in educational environments, and the impediments that are linked to the teachers' roles in design processes of digital fabrication. Based on a research study...... with eight primary and lower secondary teachers, the findings point to four central impediments for integrating digital fabrication and design into school environments. The findings extend current perceptions of digital technology in education towards exploratory processes of investigation in which......Digital fabrication technologies are increasingly integrated across subjects in primary and secondary education. Focus on the potentials of these technologies has mainly been on the support to STEM oriented learning goals, while emphasis on teachers' roles with the new learning processes...

  10. Sandia programs relevant to microelectronics fabrication

    Energy Technology Data Exchange (ETDEWEB)

    Picraux, S.T.; Vook, F.L.; Gregory, B.L.

    1987-04-01

    This report was prepared for the Semiconductor Industry and the National Laboratories Workshop held at the National Academy of Sciences, Washington, DC, February 24, 1987. It details the current Sandia program activities relevant to microelectronics fabrication.

  11. Laminate mechanics for balanced woven fabrics

    NARCIS (Netherlands)

    Akkerman, Remko

    2006-01-01

    Laminate mechanics equations are presented for composites with balanced woven fabric reinforcements. It is shown that mimicking these textile composites with equivalent transversely isotropic (‘unidirectional’) layers requires disputable manipulations. Various micromechanics predictions of textile

  12. Studies on Wicking Behaviour of Polyester Fabric

    Directory of Open Access Journals (Sweden)

    Arobindo Chatterjee

    2014-01-01

    Full Text Available This paper aims to investigate vertical wicking properties of polyester fabric based on change in sample direction and change in tension. Also experimental results are compared with theoretical results. Polyester fabric made out of spun yarn with four types of variation in pick density was used. Theoretical values of vertical wicking were calculated by using Lucas-Washburn equation and experimental results were recorded using strip test method. Maximum height reached experimentally in both warp way and weft way is more than that of the theoretical values. The maximum height attained by fabric experimentally in weft is more as compared to warp way. Vertical wicking increases with increase in tension. This paper is focused on wicking which plays a vital role in determining comfort and moisture transport behavior of fabric.

  13. Fabrication Process Development for Light Deformable Mirrors

    Data.gov (United States)

    National Aeronautics and Space Administration — The project objective is to develop robust, reproductibble fabrication processes to realize functional deformable membrane mirrors (DM) for a space mission in which...

  14. Fabrication of 3D Silicon Sensors

    Energy Technology Data Exchange (ETDEWEB)

    Kok, A.; Hansen, T.E.; Hansen, T.A.; Lietaer, N.; Summanwar, A.; /SINTEF, Oslo; Kenney, C.; Hasi, J.; /SLAC; Da Via, C.; /Manchester U.; Parker, S.I.; /Hawaii U.

    2012-06-06

    Silicon sensors with a three-dimensional (3-D) architecture, in which the n and p electrodes penetrate through the entire substrate, have many advantages over planar silicon sensors including radiation hardness, fast time response, active edge and dual readout capabilities. The fabrication of 3D sensors is however rather complex. In recent years, there have been worldwide activities on 3D fabrication. SINTEF in collaboration with Stanford Nanofabrication Facility have successfully fabricated the original (single sided double column type) 3D detectors in two prototype runs and the third run is now on-going. This paper reports the status of this fabrication work and the resulted yield. The work of other groups such as the development of double sided 3D detectors is also briefly reported.

  15. Flame retardant treatments of PBI fabric.

    Science.gov (United States)

    Temin, S. C.

    1972-01-01

    Fabrics knitted or woven from polybenzimidazole (PBI) fibers were treated to reduce flammability in oxygen atmospheres, particularly that of 5 psia oxygen. Bromination to approximately 15% weight gain of such fabrics led to markedly lower burning rates; samples brominated to over 80% weight gain were self-extinguishing in 5 psia oxygen. The loss in tensile strength of fabrics due to bromination was negligible although shrinkage was observed. Free fibers showed negligible losses on bromination. Treatment of PBI fabric with organophosphorus compounds also achieved self-extinguishing character in 5 psia oxygen but the enhanced flameproofing was largely lost on leaching. Reaction with POCl3 in pyridine led to a permanent reduction in flammability.

  16. Wireless fabric patch sensors for wearable healthcare.

    Science.gov (United States)

    Yoo, Hoi-Jun; Yoo, Jerald; Yan, Long

    2010-01-01

    Two novel wireless fabric patch sensors are introduced for low energy wearable healthcare. The first is a wirelessly powered patch sensor that can be attached to a patient to capture electrocardiogram (ECG) while consuming only 12 microW. By using fabric circuit board technology, the band-aid like sensor is implemented. The second wearable cardiac heathcare sensor, fabricated in the form of 4-layer compact smart poultice type including flexible battery, can extend to monitor bio-impedance together with ECG signals at 16 different sites of the heart with 25 reconfigurable electrodes. It also provides cm-range inductive coupled remote system start-up and duty-cycled data transmission using body as communication channel for a low energy wireless interconnectivity. Both sensors exploit dry fabric electrodes to minimize skin irritation during clinical long term operation.

  17. Semiconductors detectors: basics principals, fabrication and repair

    International Nuclear Information System (INIS)

    Souza Coelho, L.F. de.

    1982-05-01

    The fabrication and repairing techniques of semiconductor detectors, are described. These methods are shown in the way they are applied by the semiconductor detector laboratory of the KFA-Julich, where they have been developed during the last 15 years. The history of the semiconductor detectors is presented here, being also described the detector fabrication experiences inside Brazil. The key problems of manufacturing are raised. In order to understand the fabrication and repairing techniques the working principles of these detectors, are described. The cases in which worked during the stay in the KFA-Julich, particularly the fabrication of a plane Ge (Li) detector, with side entry, and the repair of a coaxial Ge (Li) is described. The vanguard problems being researched in Julich are also described. Finally it is discussed a timetable for the semiconductor detector laboratory of the UFRJ, which laboratory is in the mounting stage now. (Author) [pt

  18. Diffractive optics: design, fabrication, and test

    National Research Council Canada - National Science Library

    O'Shea, Donald C

    2004-01-01

    This book provides the reader with the broad range of materials that were discussed in a series of short courses presented at Georgia Tech on the design, fabrication, and testing of diffractive optical elements (DOEs...

  19. Fabrication of Nickel Nanotube Using Anodic Oxidation and Electrochemical Deposition Technologies and Its Hydrogen Storage Property

    Directory of Open Access Journals (Sweden)

    Yan Lv

    2016-01-01

    Full Text Available Electrochemical deposition technique was utilized to fabricate nickel nanotubes with the assistance of AAO templates. The topography and element component of the nickel nanotubes were characterized by TEM and EDS. Furthermore, the nickel nanotube was made into microelectrode and its electrochemical hydrogen storage property was studied using cyclic voltammetry. The results showed that the diameter of nickel nanotubes fabricated was around 20–100 mm, and the length of the nanotube could reach micron grade. The nickel nanotubes had hydrogen storage property, and the hydrogen storage performance was higher than that of nickel powder.

  20. Radiation damage in components

    International Nuclear Information System (INIS)

    Takano, Tomehachi

    1977-01-01

    The performance change of typical capacitors and resistors in electronic components by Co-60 γ-irradiation from the 1320 Ci source was examined in the range of 10 5 to 10 8 R. Specifically, the characteristic change during irradiation and the recovery after irradiation were continuously observed. The capacity change is +2.4% at maximum in ceramic and metallized paper capacitors, and -2.4% at maximum in mylar and paper capacitors. It is also +-0.4% at maximum in mica and polystyrene capacitors. Some of these capacitors showed the recovery of the capacity change, but the others did not. Dielectric loss varied by 15% at larger dose in some capacitors, and the recovery was not observed. While, the insulation resistance of the resistors of 10 15 Ω or more lowered to 10 13 Ω or less after 10 to 30 sec. irradiation, but recovered soon nearly to the initial values after irradiation was interrupted. The resistance change of carbon film resistors is about 0.2 to 2%, and recovered to the initial values in 100 hours after irradiation. The resistance change of composition resistors is large over the range of -13 to +35%, besides, no sign of recovery was seen. In carbon film resistors, the surface insulated type indicated far better results which are assumed to be caused by the selection of element materials and the forming of coating materials. (Wakatsuki, Y.)