Oxide formation and precipitation behaviors on interface of F82H steel joints during HIPing and hot pressing

International Nuclear Information System (INIS)

Kishimoto, H.; Ono, T.; Sakasegawa, H.; Tanigawa, H.; Ando, M.; Shibayama, T.; Kohno, Y.; Kohyama, A.

2013-01-01

Joining technologies for F82H steels are important issues for the development of fusion energy. The hot isostatic pressing (HIP) method is appropriate for consolidating the first wall of the blanket because of the flexibility of the shape of HIPed products. The HIP method is planned for fabricating a complex-shaped first wall component with built-in cooling channels; thus, accumulation of studies of microstructural and mechanical property changes, especially lower toughness of the HIPed joints, is essential. Present research aims to reveal the microstructural evolution of F82H joints fabricated by the HIP method compared with joints fabricated by hot pressing, focusing on the formation of oxides on the interface. F82H joints were characterized using 1/3-scale Charpy V-notch impact test, transmission electron microscope, scanning electron microscope, and electron probe analysis to survey the microstructural characteristics of the interface

Material properties of the F82H melted in an electric arc furnace

Energy Technology Data Exchange (ETDEWEB)

Sakasegawa, Hideo, E-mail: sakasegawa.hideo@jaea.go.jp [Japan Atomic Energy Agency, Rokkasho, Aomori (Japan); Tanigawa, Hiroyasu [Japan Atomic Energy Agency, Rokkasho, Aomori (Japan); Kano, Sho; Abe, Hiroaki [Institute for Materials Research, Tohoku university, Sendai, Miyagi (Japan)

2015-10-15

Highlights: • We studied material properties of reduced activation ferritic/martensitic steel. • We melted F82H using a 20 tons electric arc furnace for the first time. • Mass effect likely affected material properties. • MX (M: Metal, C: Carbon and/or Nitrogen) precipitates mainly formed on grain and sub grain boundaries. - Abstract: Fusion DEMO reactor requires over 11,000 tons of reduced activation ferritic/martensitic steel. It is necessary to develop the manufacturing technology for fabricating such large-scale steel with appropriate mechanical properties. In this work, we focused fundamental mechanical properties and microstructures of F82H-BA12 heat which was melted using a 20 tons electric arc furnace followed by electroslag remelting process. Its raw material of iron was blast furnace iron, because the production volume of electrolytic iron which has been used in former heats, is limited. After melting and forging, this F82H-BA12 heat was heat-treated in four different conditions to consider their fluctuations and to optimize them, and tensile and Charpy impact tests were then performed. The result of these mechanical properties were comparable to those of former F82H heats less than 5 tons which were melted applying vacuum induction melting.

Scale structure of aluminised F82H-mod. steel after HIP treatment

International Nuclear Information System (INIS)

Glasbrenner, H.; Stein-Fechner, K.; Konys, J.

2000-01-01

Coatings on low activation steels are required in fusion technology in order to reduce the tritium permeation rate through the steel into the cooling water system by a factor of at least 100. Alumina seems to be a promising coating material. However, an appropriate coating system must also have the potential for self-healing since the ceramic alumina scale tends to fail if mechanical stress is applied. A technology is introduced to form a ductile Al enriched surface scale on F82H-mod steel (Fe-7.7% Cr) and on top of it alumina. This technology consists of two main process steps. Hot dip aluminising has been performed at 700 deg. C for 30 s to the steel in order to introduce Al to the surface near zone by an easy way. The very hard intermetallic scale Fe 2 Al 5 which forms during the immersion process gets completely transformed into FeAl 2 , FeAl and α-Fe(Al) phases during a subsequent HIP process step at high pressure at 1040 deg. C and 30 min. The pressure chosen for the HIP experiment was 3000 bar. Compared to a heat treatment without superimposed high pressure pores formation due to the Kirkendall effect could be suppressed successfully. The influence of the high pressure on the heat treatment (1040 deg. C, 30 min) will be discussed in this paper

Metallurgical Characterization of Reduced Activation Martensitic Steel F-82H Modified

International Nuclear Information System (INIS)

Fernandez, P.; Lapena, J.; Lancha, A.M.; Gomez-Briceno, D.; Schirra, M.

1999-12-01

During 1995-1998 within of research and development programs on reduced ferritic/martensitic steels for fusion, metallurgical characterization of 8Cr-2WVTa steel, denominated F-28H modified, have been carried out. The work has focused on studying the microstructural and mechanical (tensile, creep, low cycle fatigue and charpy) characteristics of as-received state and aged material in the temperature range 300 degree centigrade to 600 degree centigrade for periods up to 5000 h. (Author) 45 refs

Weldability of dissimilar joint between F82H and SUS316L under fiber laser welding

Energy Technology Data Exchange (ETDEWEB)

Serizawa, Hisashi [Joining and Welding Research Institute, Osaka University, 11-1 Mihogaoka, Ibaraki, Osaka 567-0047 (Japan); Mori, Daiki; Shirai, Yuma; Ogiwara, Hiroyuki; Mori, Hiroaki [Graduate School of Engineering, Osaka University, 2-1 Yamadaoka, Suita, Osaka 565-0871 (Japan)

2013-10-15

Highlights: • The microstructure of F82H/SUS316L dissimilar joint can be divided into four regions. • In the case without beam position shift, hardness of WM cannot be reduced by PWHT. • The fiber laser welding would be applicable for constructing the dissimilar joint. -- Abstract: As one of the high beam quality heat sources, 4 kW fiber laser was applied for joining between reduced activation ferritic/martensitic steel, F82H and SUS316L austenitic stainless steel, and the microstructural analyses and Vickers hardness measurements were carried out before and after post-weld heat treatment (PWHT). The microstructure of joint can be divided into four regions which are base metal of F82H, heat affected zone (HAZ) in F82H, weld metal (WM) and base metal of SUS316L. Also, it is revealed that the high-power fiber laser can be employed for constructing butt joint between F82H and SUS316L by applying PWHT and shifting the laser beam position to SUS316L, where the distance between the contact face and beam should be set as a range from radius to diameter of laser beam.

Weldability of dissimilar joint between F82H and SUS316L under fiber laser welding

International Nuclear Information System (INIS)

Serizawa, Hisashi; Mori, Daiki; Shirai, Yuma; Ogiwara, Hiroyuki; Mori, Hiroaki

2013-01-01

Highlights: • The microstructure of F82H/SUS316L dissimilar joint can be divided into four regions. • In the case without beam position shift, hardness of WM cannot be reduced by PWHT. • The fiber laser welding would be applicable for constructing the dissimilar joint. -- Abstract: As one of the high beam quality heat sources, 4 kW fiber laser was applied for joining between reduced activation ferritic/martensitic steel, F82H and SUS316L austenitic stainless steel, and the microstructural analyses and Vickers hardness measurements were carried out before and after post-weld heat treatment (PWHT). The microstructure of joint can be divided into four regions which are base metal of F82H, heat affected zone (HAZ) in F82H, weld metal (WM) and base metal of SUS316L. Also, it is revealed that the high-power fiber laser can be employed for constructing butt joint between F82H and SUS316L by applying PWHT and shifting the laser beam position to SUS316L, where the distance between the contact face and beam should be set as a range from radius to diameter of laser beam

Hydrogen permeation measurement of the reduced activation ferritic steel F82H by the vacuum thermo-balance method

International Nuclear Information System (INIS)

Yoshida, Hajime; Enoeda, Mikio; Abe, Tetsuya; Akiba, Masato

2005-03-01

Hydrogen permeation fluxes of the reduced activation ferritic steel F82H were quantitatively measured by a newly proposed method, vacuum thermo-balance method, for a precise estimation of tritium leakage in a fusion reactor. We prepared sample capsules made of F82H, which enclosed hydrogen gas. The hydrogen in the capsules permeated through the capsule wall, and subsequently desorbed from the capsule surface during isothermal heating. The vacuum thermo-balance method allows simultaneous measurement of the hydrogen permeation flux by two independent methods, namely, the net weight reduction of the sample capsule and exhaust gas analysis. Thus the simultaneous measurements by two independent methods increase the reliability of the permeability measurement. When the gas pressure of enclosed hydrogen was 0.8 atm at the sample temperature of 673 K, the hydrogen permeation flux of F82H obtained by the net weight reduction and the exhaust gas analysis was 0.75x10 18 (H 2 /m 2 s) and 2.2x10 18 (H 2 /m 2 s), respectively. The ratio of the hydrogen permeation fluxes obtained by the net weight reduction to that measured by the exhaust gas analysis was in the range from 1/4 to 1/1 in this experiment. The temperature dependence of the estimated permeation flux was similar in both methods. Taking the uncertainties of both measurements into consideration, both results are supposed to be consistent. The enhancement of hydrogen permeation flux was observed from the sample of which outer surface was mechanically polished. Through the present experiments, it has been demonstrated that the vacuum thermo-balance method is effective for the measurement of hydrogen permeation rate of F82H. (author)

Small specimen test technology of fracture toughness in structural material F82H steel for fusion nuclear reactors

International Nuclear Information System (INIS)

Wakai, Eiichi; Ohtsuka, Hideo; Jitsukawa, Shiro; Matsukawa, Shingo; Ando, Masami

2006-03-01

Small specimen test technology (SSTT) has been developed to investigate mechanical properties of nuclear materials. SSTT has been driven by limited availability of effective irradiation volumes in test reactors and accelerator-based neutron and charged particle sources, and it is very useful for the reduction of waste materials produced in nuclear engineering. In this study new bend test machines have been developed to obtain fracture behaviors of F82H steel for very small bend specimens of pre-cracked t/2-1/3CVN (Charpy V-notch) with 20 mm-length and DFMB (deformation and fracture mini bend specimen) with 9 mm-length and disk compact tension of 0.18DCT type, and fracture behaviors were examined to evaluate DBTT (ductile-brittle transition temperature) at temperature from -180 to 25degC. The effect of specimen size on DBTT of F82H steel was also examined by using Charpy type specimens such as 1/2t-CVN, 1/3CVN and t/2-1/3CVN. In this paper, it also provides the information of the specimens irradiated at 250degC and 350degC to about 2 dpa in the capsule of 04M-67A and 04M-68A of JMTR experiments. (author)

Mechanical properties of TIG and EB weld joints of F82H

Energy Technology Data Exchange (ETDEWEB)

Hirose, Takanori, E-mail: hirose.takanori@jaea.go.jp; Sakasegawa, Hideo; Nakajima, Motoki; Tanigawa, Hiroyasu

2015-10-15

Highlights: • Narrow groove TIG minimized volume of F82H weld. • Mechanical properties of TIG and EB welds of F82H have been characterized. • Post weld heat treatment successfully moderate the toughness of weld metal without softening the base metal. - Abstract: This work investigates mechanical properties of weld joints of a reduced activation ferritic/martensitic steel, F82H and effects of post weld heat treatment on the welds. Vickers hardness, tensile and Charpy impact tests were conducted on F82H weld joints prepared using tungsten-inert-gas and electron beam after various heat treatments. Although narrow groove tungsten-inert-gas welding reduced volume of weld bead, significant embrittlement was observed in a heat affected zone transformed due to heat input. Post weld heat treatment above 993 K successfully moderated the brittle transformed region. The hardness of the brittle region strongly depends on the heat treatment temperature. Meanwhile, strength of base metal was slightly reduced by the treatment at temperature ranging from 993 to 1053 K. Moreover, softening due to double welding was observed only in the weld metal, but negligible in base metal.

Basic characterization of low-activated F82H-mod steel as compared to OPTIFER

International Nuclear Information System (INIS)

Schirra, M.; Adelhelm, C.; Graf, P.; Heger, S.; Kempe, H.; Zimmermann, H.

1997-12-01

Low-activated F82H-model steel plate material was made available to the European laboratories by the Japanese side. Basic characterization work is being performed by FZK/IMF. In the present report, the results obtained shall be compared with the European OPTIFER types. The chemical composition and the state as delivered are controlled. In addition, transformation, hardness and tempering behaviors shall be described. Tensile strength and impact bending strength were determined in the ranges of RT to 700 C and -80 C to +80 C, respectively. Particular attention is paid to the creep strength behavior. The current tests cover the range of up to 15000 h at temperatures ranging from 450 to 700 C. It can be noticed that the results measured for some parameters are subject to considerable scattering. As compared to previous tests, the experimental scope therefore had to be increased significantly. (orig.) [de

Behaviour of F82H mod. stainless steel in lead-bismuth under temperature gradient

Science.gov (United States)

Gómez Briceño, D.; Martín Muñoz, F. J.; Soler Crespo, L.; Esteban, F.; Torres, C.

2001-07-01

Austenitic steels can be used in a hybrid system in contact with liquid lead-bismuth eutectic if the region of operating temperatures is not beyond 400°C. For higher temperatures, martensitic steels are recommended. However, at long times, the interaction between the structural material and the eutectic leads to the dissolution of some elements of the steel (Ni, Cr and Fe, mainly) in the liquid metal. In a non-isothermal lead-bismuth loop, the material dissolution takes place at the hot leg of the circuit and, due to the mass transfer, deposition occurs at the cold leg. One of the possible ways to improve the performance of structural materials in lead-bismuth is the creation of an oxide layer. Tests have been performed in a small natural convection loop built of austenitic steel (316L) that has been operating for 3000 h. This loop contains a test area in which several samples of F82Hmod. martensitic steel have been tested at different times. A gas with an oxygen content of 10 ppm was bubbled in the hot area of the circuit during the operation time. The obtained results show that an oxide layer is formed on the samples introduced in the loop at the beginning of the operation and this layer increases with time. However, the samples introduced at different times during the loop operation, are not protected by oxide layers and present material dissolution in some cases.

Behaviour of F82H mod. stainless steel in lead-bismuth under temperature gradient

International Nuclear Information System (INIS)

Gomez Briceno, D.; Martin Munoz, F.J.; Soler Crespo, L.; Esteban, F.; Torres, C.

2001-01-01

Austenitic steels can be used in a hybrid system in contact with liquid lead-bismuth eutectic if the region of operating temperatures is not beyond 400 deg. C. For higher temperatures, martensitic steels are recommended. However, at long times, the interaction between the structural material and the eutectic leads to the dissolution of some elements of the steel (Ni, Cr and Fe, mainly) in the liquid metal. In a non-isothermal lead-bismuth loop, the material dissolution takes place at the hot leg of the circuit and, due to the mass transfer, deposition occurs at the cold leg. One of the possible ways to improve the performance of structural materials in lead-bismuth is the creation of an oxide layer. Tests have been performed in a small natural convection loop built of austenitic steel (316L) that has been operating for 3000 h. This loop contains a test area in which several samples of F82Hmod. martensitic steel have been tested at different times. A gas with an oxygen content of 10 ppm was bubbled in the hot area of the circuit during the operation time. The obtained results show that an oxide layer is formed on the samples introduced in the loop at the beginning of the operation and this layer increases with time. However, the samples introduced at different times during the loop operation, are not protected by oxide layers and present material dissolution in some cases

Chemical segregation behavior under thermal aging of the low-activation F82H-modified steel

International Nuclear Information System (INIS)

Lapena, J.; Garcia-Mazario, M.; Fernandez, P.; Lancha, A.M.

2000-01-01

In this work, thermal aging of the low-activation F82H-modified steel has been performed at temperatures in the range 300-600 deg. C during periods up to 5000 h. A detailed mechanical and microstructural characterization has been carried out in the aged materials, as well as in the as-received state material for reference. Auger electron spectroscopy (AES) analysis has been performed for these materials to study the microchemistry at the grain boundaries. The results show a decrease of the impact properties after aging at 600 deg. C that has been related to the precipitation of the Laves phase. Auger analyses show chromium enrichment and iron depletion at grain boundaries in all material conditions. In addition, sulphur and tungsten have been observed by this technique at grain boundaries, their presence and distribution being dependent on the material state

Proton irradiation effects on tensile and bend-fatigue properties of welded F82H specimens

Energy Technology Data Exchange (ETDEWEB)

Saito, S., E-mail: saito.shigeru@jaea.go.j [JAEA Tokai, J-PARC Center, 2-4 Shirakata-shirane, Tokai-mura, Naka-gun, Ibaraki-ken 319-1195 (Japan); Kikuchi, K.; Hamaguchi, D. [JAEA Tokai, J-PARC Center, 2-4 Shirakata-shirane, Tokai-mura, Naka-gun, Ibaraki-ken 319-1195 (Japan); Usami, K.; Ishikawa, A.; Nishino, Y.; Endo, S. [JAEA Tokai, Department of Hot Laboratories, Tokai-mura, Ibaraki-ken 319-1195 (Japan); Kawai, M. [KEK, Tsukuba-shi, Ibaraki-ken 305-0801 (Japan); Dai, Y. [PSI, Spallation Source Division, 5232 Villigen PSI (Switzerland)

2010-03-15

In several institutes, research and development for an accelerator-driven transmutation system (ADS) have been progressed. Ferritic/martensitic (FM) steels are the candidate materials for the beam window of ADS. To evaluate of the mechanical properties of the irradiated materials, the post irradiation examination (PIE) work of the SINQ (Swiss spallation neutron source) target irradiation program (STIP) specimens was carried out at JAEA. In present study, the results of PIE on FM steel F82H and its welded joint have been reported. The present irradiation conditions of the specimens were as follows: proton energy was 580 MeV. Irradiation temperatures were ranged from 130 to 380 deg. C, and displacement damage level was ranged from 5.7 to 11.8 dpa. The results of tensile tests performed at 22 deg. C indicated that the irradiation hardening occurred with increasing the displacement damage up to 10.1 dpa at 320 deg. C irradiation. At higher dose (11.8 dpa) and higher temperature (380 deg. C), irradiation hardening was observed, but degradation of ductility was relaxed in F82H welded joint. In present study, all specimens kept its ductility after irradiation and fractured in ductile manner. The results on bend-fatigue tests showed that the fatigue life (N{sub f}) of F82H base metal irradiated up to 6.3 dpa was almost the same with that of unirradiated specimens. The N{sub f} of the specimens irradiated up to 9.1 dpa was smaller than that of unirradiated specimens. Though the number of specimen was limited, the N{sub f} of F82H EB (15 mm) and EB (3.3 mm) welded joints seemed to increase after irradiation and the fracture surfaces of the specimens showed transgranular morphology. While F82H TIG welded specimens were not fractured by 10{sup 7} cycles.

In-pile Tritium Permeation through F82H Steel with and without a Ceramic Coating of Cr2O3-SiO2 Including CrPO4

International Nuclear Information System (INIS)

Nakamichi, M.; Hayashi, K.; Kulsartov, T.V.; Afanasyev, S.E.; Shestakov, V.P.; Chikhray, Y.V.; Kenzhin, E.A.; Kolbaenkov, A.N.

2006-01-01

Development of coating on blanket structural materials with significant reduction capability of tritium permeation is highly required in order to realize a reasonable design of a tritium recovery and processing system of demonstration (DEMO) fusion reactors. An effective coating has been developed in Japan Atomic Energy Agency (JAEA) using a ceramic material of Cr 2 O 3 -SiO 2 including CrPO 4 . In previous out-of-pile deuterium permeation experiments at 600 o C [T.V. Kulsartov et al., Fusion Eng. Des. 81 (2006) 701], a significant permeation reduction factor (PFR) of about 300 was obtained for the coating on the inner-side surface of tubular diffusion cells made by ferritic steel (F82H). In the present study, in-pile experiments on tritium permeation were conducted for F82H steel with and without the same coating, using a testing reactor IGV-1M in Kazakhstan. The tritium source used was liquid lithium-lead eutectics, Pb17Li, which was poured into a space around a tubular diffusion cell (specimen) of F82H steel with or without the coating on the inner side the cell. The irradiation time was about 4 hours, which corresponds to a fast-neuron fluence of about 2x10 21 m -2 (E > 1.1 MeV). The permeation reduction factor (PRF) was obtained by comparison of kinetics curves of tritium permeation through the diffusion cell of F82H steel with and without the coating. The PRFs at 600 and 500 o C were 292 and 30, respectively. These values are close to corresponding PRF values of 307 and 45, which had been obtained at 600 and 500 o C, respectively, in the previous out-of-pile experiments [T.V. Kulsartov et al., Fusion Eng. Des. 81 (2006) 701]. (author)

The dose dependence of fracture toughness Of F82H steel

Energy Technology Data Exchange (ETDEWEB)

Sokolov, M. [Oak Ridge National Laboratory, Materials Science and Technology Div., TN (United States); Tanigawa, H.; Ando, M.; Shiba, K. [Japan Atomic Energy Agency, Tokai-mura, Naga-gun, Ibaraki-ken (Japan); Odette, G. [UCSB, Santa-Barbara, Dept. of Mechanical Engineering UCSB, AK (United States); Hirose, T. [Blanket Engineering Group, Japan Atomic Energy Agency, Naka, Ibaraki (Japan); Klueh, R.L. [Oak Ridge Noational Laboratory, TN (United States)

2007-07-01

Full text of publication follows: The ferritic-martensitic steel F82H is a primary candidate low-activation material for fusion applications, and it is being investigated in the joint U.S. Department of Energy-Japan Atomic Energy Agency. As a part of this program, several capsules containing fracture toughness specimens were irradiated in High-Flux Isotope Reactor. These specimens were irradiated to a wide range of doses from 3.5 to 25 dpa. The range of irradiation temperature was from 250 deg. C to 500 deg. C. This paper summarizes the changes in fracture toughness transition temperature and decrease in the ductile fracture toughness as result of various irradiation conditions. It is shown that in the 3.5 to 25 dpa dose range, irradiation temperature plays the key rote in determination of the shift of the transition temperature. Highest embrittlement observed at 250 deg.C and the lowest at 500 deg. C. At a given irradiation temperature, shift of the fracture toughness transition temperature increases slightly with dose within the studied dose range. It appears that main gain in transition temperature shift occurred during initial {approx}5 dpa of irradiation. The present data are compared to the available published trends. (authors)

Fracture toughness of the IEA heat of F82H ferritic/martensitic stainless steel as a function of loading mode

Energy Technology Data Exchange (ETDEWEB)

Li, Huaxin; Gelles, D.S. [Pacific Northwest Labs., Richland, WA (United States); Hirth, J.P. [Washington State Univ., Pullman, WA (United States)] [and others

1997-04-01

Mode I and mixed-mode I/III fracture toughness tests were performed for the IEA heat of the reduced activation ferritic/martensitic stainless steel F82H at ambient temperature in order to provide comparison with previous measurements on a small heat given a different heat treatment. The results showed that heat to heat variations and heat treatment had negligible consequences on Mode I fracture toughness, but behavior during mixed-mode testing showed unexpected instabilities.

Hydrogen permeation behavior through F82H at high temperature

Energy Technology Data Exchange (ETDEWEB)

Matsuda, S.; Katayama, K.; Shimozori, M.; Fukada, S. [Interdisciplinary Graduate School of Engineering Science, Kyushu University, Kyushu (Japan); Ushida, H. [Energy Science and Engineering, Faculty of Engineering, Kyushu University, Kyushu (Japan); Nishikawa, M. [Malaysia-Japan International Institute of Technology, UTM, Kuala Lumpur (Malaysia)

2015-03-15

F82H is a primary candidate of structural material and coolant pipe material in a blanket of a fusion reactor. Understanding tritium permeation behavior through F82H is important. In a normal operation of a fusion reactor, the temperature of F82H will be controlled below 550 C. degrees because it is considered that F82H can be used up to 30,000 hours at 550 C. degrees. However, it is necessary to assume the situation where F82H is heated over 550 C. degrees in a severe accident. In this study, hydrogen permeation behavior through F82H was investigated in the temperature range from 500 to 800 C. degrees. In some cases, water vapor was added in a sample gas to investigate an effect of water vapor on hydrogen permeation. The permeability of hydrogen in the temperature range from 500 to 700 C. degrees agreed well with the permeability reported by E. Serra et al. The degradation of the permeability by water vapor was not observed. After the hydrogen permeation reached in a steady state at 700 C. degrees, the F82H sample was heated to 800 C. degrees. The permeability of hydrogen through F82H sample which was once heated up to 800 C. degrees was lower than that of the original one. (authors)

Fracture toughness of the F-82H steel-effect of loading modes, hydrogen, and temperature

International Nuclear Information System (INIS)

Li, H.-X.; Jones, R.H.; Hirth, J.P.; Gelles, D.S.

1996-01-01

The effects of loading mode, hydrogen, and temperature on fracture toughness and tearing modulus were examined for a ferritic/martensitic steel (F-82H). The introduction of a shear load component, mode III, significantly decreased the initiation and propagation resistance of cracks compared to the opening load, mode I, behavior. Mode I crack initiation and propagation exhibited the highest resistance. A minimum resistance occurred when the mode I and mode III loads were nearly equal. The presence of 4 wppm hydrogen decreased the cracking resistance compared to behavior without H regardless of the loading mode. The minimum mixed-mode fracture toughness with the presence of hydrogen was about 30% of the hydrogen-free mode I fracture toughness. The mixed-mode toughness exhibited a lesser sensitivity to temperature than the mode I toughness. The J IC value was 284 kJ/m 2 at room temperature, but only 60 kJ/m 2 at -55 C and 30 kJ/m 2 at -90 C. The ductile to brittle transition temperature (DBTT) was apparently higher than -55 C. (orig.)

Investigation of instability of M23C6 particles in F82H steel under electron and ion irradiation conditions

Science.gov (United States)

Kano, Sho; Yang, Huilong; Shen, Jingjie; Zhao, Zishou; McGrady, John; Hamaguchi, Dai; Ando, Mamami; Tanigawa, Hiroyasu; Abe, Hiroaki

2018-04-01

In order to clarify the instability of M23C6 in F82H steel under irradiation, both electron irradiation using a high voltage electron microscope (HVEM) and ion irradiation using an ion accelerator were performed. For the electron irradiation, in-situ observation under 2 MV electron irradiation and ex-situ high resolution electron microscopic (HREM) analysis were utilized to evaluate the response of M23C6 against irradiation. The temperature dependence of the irradiation induced instability of the carbide was first confirmed: 293 K indicating severe loss of crystallinity due to dissolution of the constituent atoms though irradiation-enhanced diffusion under the vacancy diffusion by the focused electron beam irradiation. For the ion irradiation, 10.5 MeV-Fe3+ ion was applied to bombard the F82H steel at 673 K to achieve the displacement damage of ≈20 dpa at the depth of 1.0 μm from surface. Cross-section TEM specimens were prepared by a focused ion beam technique. The shrinkage of carbide particles was observed especially near the irradiation surface. Besides, the lattice fringes at the periphery of carbide were observed in the irradiated M23C6 by the HREM analysis, which is different from that observed in the electron irradiation. It was clarified that the instability of M23C6 is dependent on the irradiation conditions, indicating that the flow rate of vacancy type defects might be the key factor to cause the dissolution of constituent atoms of carbide particles into matrix under irradiation.

Effect of He implantation on fracture behavior and microstructural evolution in F82H

Energy Technology Data Exchange (ETDEWEB)

Yabuuchi, Kiyohiro, E-mail: kiyohiro.yabuuchi@qse.tohoku.ac.jp [Department of Quantum Science and Energy Engineering, Tohoku University, 6-6-01-2, Aramaki-Aza-Aoba, Aobaku, Sendai, Miyagi 980-8579 (Japan); Sato, Kiminori; Nogami, Shuhei; Hasegawa, Akira [Department of Quantum Science and Energy Engineering, Tohoku University, 6-6-01-2, Aramaki-Aza-Aoba, Aobaku, Sendai, Miyagi 980-8579 (Japan); Ando, Masami; Tanigawa, Hiroyasu [Japan Atomic Energy Agency, 2-166, Oaza-Obuchi-Aza-Omotedate, Rokkasho-mura, Kamikita-gun, Aomori 039-3212 (Japan)

2014-12-15

Reduced-activation ferritic/martensitic steels (RAFMs) are the primary candidate structural materials for fusion reactor blanket components. He bubbles, which formed under 14 MeV neutron irradiation, is considered to cause some mechanical property changes. In a previous study, Hasegawa et al. investigated the fracture behavior using Charpy impact test of He implanted F82H by 50 MeV α-particles with cyclotron accelerator, and the ductile brittle transition temperature (DBTT) was increased and intergranular fracture (IGF) was observed. However, the cause of the IGF was not shown in the previous study. To clarify the cause of the IGF of the He implanted F82H by 50 MeV α-particles with cyclotron accelerator, the microstructure of the He implanted F82H was investigated. After Charpy impact test at 233 K, the brittle fracture surface of the He implanted specimen was observed by SEM and TEM. By SEM observation, grain boundary surface was clearly observed from the bottom of the notch to a depth of about 400 μm. This area correspond to the He implanted region. On the other hand, at unimplanted region, river pattern was observed and transgranular fracture occurred. TEM observation revealed the He bubbles agglomeration at dislocations, lath boundaries, and grain boundaries, and the coarsening of precipitates on grain boundaries. IGF of the He implanted F82H was caused by both He bubbles and coarsening precipitates.

A microstructural study of F82H-MOD. Plate, powder HIP and EB and TIG weldments

International Nuclear Information System (INIS)

Schuring, E.W.

1998-06-01

F82H is the heat identification number of a ferritic/martensitic steel. The steel has a chemical composition resulting in low activation after neutron irradiation. At ECN a microstructural study was conducted on plates of F82H (73, 15 and 25mm thick), a bar of HIPped F82H and EB and TIG welds in F82H plates. The investigation was aimed to characterise the microstructures for reference in irradiation experiments. The F82H mod. plates have a martensitic matrix with carbide precipitation on the prior austenite grain boundaries and the martensite laths. The carbide precipitation is most pronounced on the prior austenite grain boundaries. The PAG is comparable for the three plate thicknesses investigated. In two plates faint segregation bands were found with a denser carbide precipitation and 8-ferrite. Further Ta, Ti and Zr containing oxides are present. Hardness measurements show a higher overall hardness in the 25mm plate investigated compared to the 7.5 and 15mm plates. The F82H HIP bar shows a homogeneous PAG throughout the diameter. The microstructure shows a zone starting at about 1 mm below the surface with a width of 14mm, with a relatively high concentration of low precipitation density ferritic like fields, which corresponds to a zone with a 15HV5 lower hardness with respect to the rest of the bar. This zone is expected to be related to the HIP process. Further in the microstructure a circular pattern of W and Ta enriched inclusions is found, which mark the original HIP-powder grain boundaries. The EB-welds were manufactured by two manufactures and differ mostly in the heat input, resulting in differences in HAZ-width and the width of the weld cap. The F82H EB welds show comparable microstructures in the weld pool, with a martensitic microstructure free of carbides. All EB-welds contain 8-ferrite in concentrations of 0.1-1%. In the heat affected zone (HAZ), the coarse grained HAZ (CGHAZ) is free of carbide precipitation, whereas the fine grained HAZ (FGHAZ

Study of neutron irradiation on F82H alloys by Mössbauer spectroscopy

Energy Technology Data Exchange (ETDEWEB)

Huang, S.S., E-mail: h.shaosong@ht8.ecs.kyoto-u.ac.jp; Kitao, S.; Kobayashi, Y.; Yoshiie, T.; Xu, Q.; Sato, K.; Seto, M.

2015-01-15

The effects of neutron irradiation on F82H ferritic/martensitic stainless steel and its model alloys were studied by Mössbauer spectroscopy. The microstructural damage mechanisms of these alloys, during the void incubation period were interpreted using the short range order (SRO) parameters. Results show that within Fe–8Cr alloy, the atoms in the nearest neighbor (NN) of the Fe nuclei were inhomogeneous, prior to irradiation. A configuration trapping model of Cr supported the negative average SRO observed for the NN shells in our Fe–Cr alloys. We found that irradiation also accelerated the SRO in Fe–8Cr through a diffusion mechanism, where Cr atom repulsion was concentration dependent. Finally, comparative studies were conducted on F82H model alloys using the present Mössbauer measurements and our previously reported work on positron annihilation spectroscopy, which further established that irradiation of the alloys promoted the growth of a M{sub 23}C{sub 6} complex.

Evaluation of Cu as an interlayer in Be/F82H diffusion bonds for ITER TBM

Energy Technology Data Exchange (ETDEWEB)

Hunt, R.M., E-mail: rhunt@ucla.edu [Mechanical and Aerospace Engineering Department, UCLA, 44-128 Engineering IV, 420 Westwood Plaza, Los Angeles, CA 90025-1597 (United States); Goods, S.H., E-mail: shgoods@sandia.gov [Sandia National Laboratories, 7011 East Ave., Livermore, CA 94550 (United States); Ying, A., E-mail: ying@fusion.ucla.edu [Mechanical and Aerospace Engineering Department, UCLA, 44-128 Engineering IV, 420 Westwood Plaza, Los Angeles, CA 90025-1597 (United States); Dorn, C.K., E-mail: christopher_dorn@brushwellman.com [Brush Wellman Inc., 14710 W. Portage River So. Road, Elmore, OH 43416 (United States); Abdou, M., E-mail: abdou@fusion.ucla.edu [Mechanical and Aerospace Engineering Department, UCLA, 44-128 Engineering IV, 420 Westwood Plaza, Los Angeles, CA 90025-1597 (United States)

2011-10-01

Copper has been investigated as a potential interlayer material for diffusion bonds between beryllium and Reduced Activation Ferritic/Martensitic (RAFM) steel. Utilizing Hot Isostatic Pressing (HIP), copper was directly bonded to a RAFM steel, F82H, at 650 deg. C, 700 deg. C, 750 deg. C, 800 deg. C and 850 deg. C, under 103 MPa for 2 h. Interdiffusion across the bonded interface was limited to 1 {mu}m or less, even at the highest HIP'ing temperature. Through mechanical testing it was found that samples HIP'ed at 750 deg. C and above remain bonded up to 211 MPa under tensile loading, at which point ductile failure occurred in the bulk copper. As titanium will be used as a barrier layer to prevent the formation of brittle Be/Cu intermetallics, additional annealing studies were performed on copper samples coated with a titanium thin film to study Ti/Cu interdiffusion characteristics. Samples were heated to temperatures between 650 deg. C and 850 deg. C for 2 h in order to mimic the range of likely HIP temperatures. A correlation was drawn between HIP temperature and diffusion depth for use in determining the minimum Ti film thickness necessary to block diffusion in the Be/F82H joint.

Effect of laser beam position on mechanical properties of F82H/SUS316L butt-joint welded by fiber laser

Energy Technology Data Exchange (ETDEWEB)

Serizawa, Hisashi, E-mail: serizawa@jwri.osaka-u.ac.jp [Joining and Welding Research Institute, Osaka University, 11-1 Mihogaoka, Ibaraki, Osaka 567-0047 (Japan); Mori, Daiki; Ogiwara, Hiroyuki; Mori, Hiroaki [Graduate School of Engineering, Osaka University, 2-1 Yamadaoka, Suita, Osaka 565-0871 (Japan)

2014-10-15

Highlights: • The micro hardness of weld metal in F82H/SUS316L joint partially decreases after PWHT by shifting beam position to SUS316L. • Charpy impact energy of F82H/SUS316L joint obviously increases after PWHT due to the release of residual stress. • The tensile strength of weld metal in F82H/SUS316L joint is higher than that of SUS316L. • The fiber laser welding seems to be one of the most candidate methods to join between F82H and SUS316L pipes practically. - Abstract: A dissimilar butt-joint between reduced activation ferritic/martensitic steel F82H and SUS316L austenitic stainless steel was made by 4 kW fiber laser and the influence of laser beam position on its mechanical properties before and after post-weld heat treatment (PWHT) was examined at room temperature. From the nano-indentation measurements and the microstructural observations, it is found that the micro hardness of weld metal partially decreases after PWHT by shifting beam position to SUS316L because its phase seems to move from only the martensitic phase to the mixture of austenitic and martensitic phases. In addition, Charpy impact test suggests that the impact energy slightly increases by shifting beam position before PWHT and obviously increases after PWHT due to the release of residual stress. Moreover, the tensile test indicates that the tensile strength of weld metal is higher than that of SUS316L and the fracture occurs at the base metal of SUS316L regardless of laser beam position.

Materials design data for reduced activation martensitic steel type F82H

Energy Technology Data Exchange (ETDEWEB)

Tavassoli, A.-A.F. E-mail: tavassoli@cea.fr; Rensman, J.-W.; Schirra, M.; Shiba, K

2002-11-01

This paper presents materials data for design of ITER test blanket modules with the reduced activation ferritic martensitic steel type F82H as structural material. From the physical properties databases, variations of modulus of elasticity, density, thermal conductivity, thermal diffusivity, specific heat, mean and instantaneous linear coefficients of thermal expansion versus temperature are derived. Also reported are Poisson's ratio and magnetic properties. From the tension test results, nominal and minimum stress values of S{sub y} and S{sub u} are derived and used for calculation of allowable primary membrane stress intensity S{sub m}. Likewise, uniform and total elongations, as well as reduction of area data, are used for calculation of minimum and true ductility at rupture values. From the instrumented Charpy impact and fracture toughness test data, ductile to brittle transition temperature, toughness and behavior of material in different fracture modes are evaluated. The effect of specimen size and geometry are discussed but preference is given to standard size specimens. From the fatigue data, total strain range versus number of cycles to failure curves are plotted and used to derive fatigue design curves, using a reduction factor of 2 on strain and a reduction factor of 20 on number of cycles to failure. Cyclic hardening curves are also derived and compared with monotonic hardening curves. From the creep data, time dependent allowable stresses S{sub r} and S{sub t} are calculated. Combination of tension and creep results are used to deduce S{sub mt} and isochronus curves. Finally, irradiated and aged materials data are compared to insure that the safety margins incorporated in unirradiated design limits are not exceeded.

Impact properties of reduced activation ferritic/martensitic steel, F82H jointed by hot isostatic pressing

Energy Technology Data Exchange (ETDEWEB)

Ogiwara, H.; Tanigawa, H. [Japan Atomic Energy Agency, Tokai-mura, Naga-gun, Ibaraki-ken (Japan); Hirose, T. [Blanket Engineering Group, Japan Atomic Energy Agency, Naka, Ibaraki (Japan); Enoeda, M. [Naka Fusion Research Establishment, J.A.E.R.I., Japan Atomic Energy Research Institute, Ibaraki-ken (Japan); Kohyama, A. [Kyoto Univ., lnstitute of Advanced Energy (Japan)

2007-07-01

Full text of publication follows: Reduced-activation ferritic/martensitic steels are the leading candidate structural material for the blanket system of fusion reactors. The important issue at the current stage is the finalization of a detailed manufacturing specification for ITER test blanket module. Hot isostatic pressing (HIP) process is one of the most important methods to fabricate the first wall with cooling channels. The objective of this paper is to optimize HIP condition to obtain the excellent joints mechanical properties. The materials used were F82H steels. The joint was produced by solid state HIP method. Before HIP treatments, specimens were heated in vacuum condition to out-gas. This treatment was conducted to decrease oxidation on the surfaces. HIP treatments were carried out for 2 h at 1100 deg. C - 140 MPa. The specimens were normalized at 960 deg. C for 0.5 h and tempered at 750 deg. C for 1.5 h. The bonding interface was characterized by scanning electron microscopy. Charpy impact tests and tensile tests were conducted to evaluate the mechanical properties of the HIP joint. Impact tests revealed that there were no significant differences in the ductile-brittle transition temperatures of HIP jointed specimens and base metal specimens, but the upper-shelf energy (USE) of the HIP joint specimens at room temperature was only about 10% of that of the base metal specimens. SEM observations of the fracture surface of HIP joint specimens revealed that a large number of oxides were formed on the HIP joint. This result indicates that oxides formed on the HIP joint are the dominant factor of the impact properties. Based on these results, the pre-HIP treatment conditions had been optimized to reduce the number of oxides, and USE of HIP joint specimens increased to about 50% of that of the base metal. The detailed analyses on the HIP joint microstructure will be reported. (authors)

Interface strength measurement of tungsten coatings on F82H substrates

International Nuclear Information System (INIS)

Kim, Hyoungil; El-Awady, Jaafar; Gupta, Vijay; Ghoniem, Nasr; Sharafat, Shahram

2009-01-01

In the current work, hot isostatic pressing is adopted to deposit tungsten coatings on F82H substrates. The interface strength of the W/F82H samples is measured using the Laser Spallation technique and the microstructure is analyzed to determine the strength of the coating. Finally, the failure mechanisms of the hot isostatic pressing versus vacuum plasma spraying tungsten coatings and their different failure strengths are compared. It is concluded that the hot isostatic pressing process ensures a good adhesion for the W/F82H interface while the vacuum plasma spraying process results in relatively lower failure strength for the W-coating itself due to the high porosity in the coating.

Study of irradiated F82H steel and its model Fe-Cr alloy by Moessbauer spectroscopy

International Nuclear Information System (INIS)

Huang, S.S.; Kitao, S.; Xu, Q.; Sato, K.; Yoshiie, T.

2013-01-01

In this work, Moessbauer spectroscopy which is a super-precision tool was conducted on F82H and its model Fe-Cr alloys before and after irradiation to take a further look on the interaction between carbides and point defects and Cr effect on microstructural evolution during irradiation in void incubation period. (J.P.N.)

Employment of fluorine doped zinc tin oxide (ZnSnOx:F) coating layer on stainless steel 316 for a bipolar plate for PEMFC

International Nuclear Information System (INIS)

Park, Ji Hun; Byun, Dongjin; Lee, Joong Kee

2011-01-01

Highlights: → Preparation of fluorine doped tin oxide (SnOx:F) and fluorine doped zinc tin oxide (ZnSnOx:F) coating layer on the surface of stainless steel 316 bipolar plate for PEMFCs (Proton Exchange Membrane Fuel Cells). → Evaluations of the corrosion resistance and the interfacial contact resistance of the bare, SnOx:F and ZnSnOx:F thin film coated stainless steel 316 bipolar plates. → Evaluation of single cell performance such as cell voltage and power density using bare stainless steel, SnOx:F and ZnSnOx:F film coated bipolar plates. - Abstract: The investigation of the electrochemical characteristics of the fluorine doped tin oxide (SnOx:F) and fluorine doped zinc tin oxide (ZnSnOx:F) was carried out in the simulated PEMFC environment and bare stainless steel 316 was used as a reference. The results showed that the ZnSnOx:F coating enhanced both the corrosion resistance and interfacial contact resistance (ICR). The corrosion current for ZnSnOx:F was 1.2 μA cm -2 which was much lower than that of bare stainless steel of 50.16 μA cm -2 . The ZnSnOx:F coated film had the smallest corrosion current due to the formation of a tight surface morphology with very few pin-holes. The ZnSnOx:F coated film exhibited the highest values of the cell voltage and power density due to its having the lowest ICR values.

Development of HIP bonding procedure and mechanical properties of HIP bonded joints for reduced activation ferritic steel F-82H

International Nuclear Information System (INIS)

Oda, Masahiro; Kurasawa, Toshimasa; Kuroda, Toshimasa; Hatano, Toshihisa; Takatsu, Hideyuki

1997-03-01

Structural materials of blanket components in fusion DEMO reactors will receive a neutron wall load more than 3-5MW/m 2 as well as exposed by surface heat flux more than 0.5MW/m 2 . A reduced activation ferritic steel F-82H has been developed by JAERI in collaboration with NKK from viewpoints of resistance for high temperature and neutron loads and lower radioactivity. This study intends to obtain basic performance of F-82H to establish the fabrication procedure of the first wall and blanket box by using Hot Isostatic Pressing (HIP) bonding. Before HIP bonding tests, effects of heat treatment temperature and surface roughness on mechanical properties of joints were investigated in the heat treatment tests and diffusion bonding tests, respectively. From these results, the optimum HIP bonding conditions and the post heat treatment were selected. Using these conditions, the HIP bonding tests were carried out to evaluate HIP bondability and to obtain mechanical properties of the joints. Sufficient HIP bonding performance was obtained under the temperature of 1040degC, the compressive stress of 150MPa, the holding time of 2h, and the surface roughness ∼μ m. Mechanical properties of HIP bonded joints with these conditions were similar to those of as-received base metal. An oxide formation on the surface to be bonded would need to be avoided for sufficient bonding. The bonding ratio, Charpy impact value and fatigue performance of the joints strongly depended on the HIP conditions, especially temperature, while micro-structure, Vickers hardness and tensile properties had little dependence on the HIP temperature. The surface roughness strongly affected the bonding ratio and would be required to be in the level of a few μ m. In the HIP bonding test of the welded material, the once-melted surface could be jointed by the HIP bonding under the above-mentioned procedure. (J.P.N.)

Post-irradiation mechanical tests on F82H EB and TIG welds

International Nuclear Information System (INIS)

Rensman, J.; Osch, E.V. van; Horsten, M.G.; D'Hulst, D.S.

2000-01-01

The irradiation behaviour of electron beam (EB) and tungsten inert gas (TIG) welded joints of the reduced-activation martensitic steel IEA heat F82H-mod. was investigated by neutron irradiation experiments in the high flux reactor (HFR) in Petten. Mechanical test specimens, such as tensile specimens and KLST-type Charpy impact specimens, were neutron irradiated up to a dose level of 2-3 dpa at a temperature of 300 deg. C in the HFR reactor in Petten. The tensile results for TIG and EB welds are as expected with practically no strain hardening capacity left. Considering impact properties, there is a large variation in impact properties for the TIG weld. The irradiation tends to shift the DBTT of particularly the EB welds to very high values, some cases even above +250 deg. C. PWHT of EB-welded material gives a significant improvement of the DBTT and USE compared to the as-welded condition

Microstructure and Hardness Variation in a TIG Weldment of Irradiated F82H

International Nuclear Information System (INIS)

Tanigawa, H.; Ando, M.; Sawai, T.; Shiba, K.; Hashimoto, N.; Klueh, R.L.

2003-01-01

Previous work reported that a TIG weld joint of F82H exhibited low irradiation hardening in a tensile test, compared to the base metal. Microhardness tests and microstructure observation on the neutron-irradiated TIG weld joint of F82H revealed that the over-tempered zone in the heat-affected zone (HAZ) exhibited this good performance. The region in the HAZ where the prior austenite grain size became very fine during welding also exhibited lower irradiation hardening. Hypotheses for these low-hardening mechanisms were proposed based on the phase diagram and grain size

Positron annihilation lifetime measurements of austenitic stainless and ferritic/martensitic steels irradiated in the SINQ target irradiation program

Energy Technology Data Exchange (ETDEWEB)

Sato, K., E-mail: ksato@rri.kyoto-u.ac.jp [Research Reactor Institute, Kyoto University, Kumatori-cho, Sennan-gun, Osaka 590-0494 (Japan); Xu, Q.; Yoshiie, T. [Research Reactor Institute, Kyoto University, Kumatori-cho, Sennan-gun, Osaka 590-0494 (Japan); Dai, Y. [Spallation Neutron Source Division, Paul Scherrer Institute, CH-5232 Villigen PSI (Switzerland); Kikuchi, K. [Frontier Research Center for Applied Atomic Sciences, Ibaraki University, Tokai-mura, Naka-gun, Ibaraki 319-1106 (Japan)

2012-12-15

Titanium-doped austenitic stainless steel (JPCA) and reduced activated ferritic/martensitic steel (F82H) irradiated with high-energy protons and spallation neutrons were investigated by positron annihilation lifetime measurements. Subnanometer-sized (<{approx}0.8 nm) helium bubbles, which cannot be observed by transmission electron microscopy, were detected by positron annihilation lifetime measurements for the first time. For the F82H steel, the positron annihilation lifetime of the bubbles decreased with increasing irradiation dose and annealing temperature because the bubbles absorb additional He atoms. In the case of JPCA steel, the positron annihilation lifetime increased with increasing annealing temperature above 773 K, in which case the dissociation of complexes of vacancy clusters with He atoms and the growth of He bubbles was detected. He bubble size and density were also discussed.

Positron annihilation lifetime measurements of austenitic stainless and ferritic/martensitic steels irradiated in the SINQ target irradiation program

International Nuclear Information System (INIS)

Sato, K.; Xu, Q.; Yoshiie, T.; Dai, Y.; Kikuchi, K.

2012-01-01

Titanium-doped austenitic stainless steel (JPCA) and reduced activated ferritic/martensitic steel (F82H) irradiated with high-energy protons and spallation neutrons were investigated by positron annihilation lifetime measurements. Subnanometer-sized (<∼0.8 nm) helium bubbles, which cannot be observed by transmission electron microscopy, were detected by positron annihilation lifetime measurements for the first time. For the F82H steel, the positron annihilation lifetime of the bubbles decreased with increasing irradiation dose and annealing temperature because the bubbles absorb additional He atoms. In the case of JPCA steel, the positron annihilation lifetime increased with increasing annealing temperature above 773 K, in which case the dissociation of complexes of vacancy clusters with He atoms and the growth of He bubbles was detected. He bubble size and density were also discussed.

Effects of helium implantation on fatigue properties of F82H-IEA heat

Energy Technology Data Exchange (ETDEWEB)

Yamamoto, N.; Murase, Y.; Nagakawa, J. [National Research Institute for Metals, Tsukuba, Ibaraki (Japan)

2007-07-01

Full text of publication follows: Ferritic steels including reduced activation ones that have been recognized as attractive structural candidates for DEMO reactors and the beyond are known to be highly resistant to helium embrittlement. However, almost studies that deduced this behavior have been carried out by means of short time experiments such as tensile tests, and a few results are available concerning long term inspections, although the detrimental helium effect appears more severely in the latter. The aim of this work is to obtain further information on the influence of helium on fatigue properties of a representative reduced activation ferritic/martensitic steel F82H (8Cr2WVTa) using helium implantation technique with a cyclotron. The material examined is an IEA heat version of F82H. In order to realize a fine grain size due to thin specimens (0.08 mm thick) for ion irradiation, normalizing was conducted at rather low temperature of 1213 K, followed by tempering at 1023 K. Helium was implanted by {alpha}-particle irradiation at 823 K, a desired highest temperature of this material for first wall application, to the concentration of 100 appm He with an implantation rate of about 1.7 x 10{sup -3} appm He/s. Subsequent fatigue tests were conducted at the same temperature as that of irradiation, not only on implanted specimens but also on reference controls which were not implanted with helium but experienced the same metallurgical histories as those of irradiated ones. After fracture, samples were observed with electron microscopes. In short time periods, it has been notified that helium introduction caused no significant deterioration of both fatigue life and extension at fracture. In addition, all specimens failed in a fully trans-crystalline and ductile manner, irrespective of whether helium was present or not. Indication of grain boundary embrittlement was therefore not discerned. These facts would reflect insusceptible characteristics of this material to

Effects of helium implantation on fatigue properties of F82H-IEA heat

International Nuclear Information System (INIS)

Yamamoto, N.; Murase, Y.; Nagakawa, J.

2007-01-01

Full text of publication follows: Ferritic steels including reduced activation ones that have been recognized as attractive structural candidates for DEMO reactors and the beyond are known to be highly resistant to helium embrittlement. However, almost studies that deduced this behavior have been carried out by means of short time experiments such as tensile tests, and a few results are available concerning long term inspections, although the detrimental helium effect appears more severely in the latter. The aim of this work is to obtain further information on the influence of helium on fatigue properties of a representative reduced activation ferritic/martensitic steel F82H (8Cr2WVTa) using helium implantation technique with a cyclotron. The material examined is an IEA heat version of F82H. In order to realize a fine grain size due to thin specimens (0.08 mm thick) for ion irradiation, normalizing was conducted at rather low temperature of 1213 K, followed by tempering at 1023 K. Helium was implanted by α-particle irradiation at 823 K, a desired highest temperature of this material for first wall application, to the concentration of 100 appm He with an implantation rate of about 1.7 x 10 -3 appm He/s. Subsequent fatigue tests were conducted at the same temperature as that of irradiation, not only on implanted specimens but also on reference controls which were not implanted with helium but experienced the same metallurgical histories as those of irradiated ones. After fracture, samples were observed with electron microscopes. In short time periods, it has been notified that helium introduction caused no significant deterioration of both fatigue life and extension at fracture. In addition, all specimens failed in a fully trans-crystalline and ductile manner, irrespective of whether helium was present or not. Indication of grain boundary embrittlement was therefore not discerned. These facts would reflect insusceptible characteristics of this material to high

Hardness distribution and tensile properties in an electron-beam-welded F82H irradiated in HFIR

International Nuclear Information System (INIS)

Hashimoto, N.; Oka, H.; Muroga, T.; Kimura, A.; Sokolov, M.A.; Yamamoto, T.

2014-01-01

F82H-IEA and its EB-weld joint were irradiated at 573 and 773 K up to 9.6 dpa in the HFIR and the irradiation effect on its mechanical properties and microstructure were investigated. A hardness profile across the weld joint before irradiation showed the hardness in transformed region (TR) was high and especially that in the edge of TR was the highest (high hardness region: HHR) compared to base metal. This hardness distribution corresponds to grain size distribution. After irradiation, hardening in HHR was small compared to other region in the sample. In tensile test, the amount of hardening in yield strength and ultimate tensile strength of F82H EB-weld joint was almost similar to that of F82H-1EA but the fracture position of EB-weld joint was at the boundary of TR and BM. Therefore, the TR/BM boundary is the structural weak point in F82H EB-weld joint after irradiation. As the plastic instability was observed, the dislocation channeling deformation can be expected though the dislocation channel was not observed in this study. (author)

Microstructural development in multi-pass TIG welded F82H steels under dual-ion irradiation

Energy Technology Data Exchange (ETDEWEB)

Ogiwara, H.; Tanigawa, H. [Japan Atomic Energy Agency, Tokai-mura, Naga-gun, Ibaraki-ken (Japan); Kishimoto, H.; Tomohiro, M.; Kohyama, A. [Kyoto Univ., Institute of Advanced Energy (Japan)

2007-07-01

Full text of publication follows: Reduced-activation ferritic/martensitic (RAFM) steels are the first candidate materials for blanket structural component. On fabricating blanket components, various joining technologies will be required, and it could be anticipated that some parts of the weldments will suffer from high-dose 14 MeV neutron irradiation. For example, the current Japanese water cooled test blanket module design has the weldment of the first wall and side wall at 25 mm from the surface. This will not be the case for TIER-TBM, but could be the critical issue if the same design is applied for DEMO blanket system. In this study, the effects of displacement damage and helium production on mechanical properties and microstructures of the multi-pass tungsten inert gas (TIG) welding were investigated. The welded joint used in this study is a multi-pass TIG weldment on 15-mm thick plates of F82H-IEA. The post weld heat treatment was carried out at 720 deg. C for 1 h. To obtain systematic and accurate information of the microstructural response under fusion environment, dual-ion irradiation was performed. 15 mm x 20 mm pieces which cover the whole TIG weldment were irradiated at 470 deg. C up to 20 dpa using 6.4 MeV Fe{sup +3} and/or energy-degraded 1.0 MeV He{sup +}. The damage rate was 1.0 x 10{sup -3} dpa/s, and the helium injection rate was 15 x 10{sup -3} appm He/s. After the irradiations, thin film samples were made from various regions of the weldment by focused ion beam (FIB) processor, and transmission electron microscopy (TEM) observation and hardness tests were performed. Microstructure and Vickers hardness profiles across base metal, heat affected zone (HAZ) and fusion zone (FZ) were examined before irradiation experiments. The hardness measurements revealed that the maximum hardness was observed at the last pass region of FZ, and the softest region was in the middle of the FZ and HAZ region near the transformation line. In the microstructure study

Synergistic effect of Ti and F co-doping on dehydrogenation properties of MgH2 from first-principles calculations

International Nuclear Information System (INIS)

Zhang, J.; Huang, Y.N.; Mao, C.; Peng, P.

2012-01-01

Highlights: ► The co-incorporation of Ti and F into MgH 2 lattice is energetically favorable. ► The incorporated Ti and F in MgH 2 preferably generate TiH 2 and MgF 2 , respectively. ► The synergistic effect of Ti and F is superior to that of pure Ti. ► The weakened interactions of Mg–H explain enhanced dehydrogenation properties. - Abstract: The energetic and electronic properties of MgH 2 co-doped with Ti and F are investigated using first-principles calculations based on density functional theory. The calculation results show that incorporation of Ti combined with F atoms into MgH 2 lattice is energetically favorable relative to single incorporation of Ti atom. After dehydrogenation, the co-doped Ti and F in MgH 2 preferably generate TiH 2 and MgF 2 , respectively. Comparatively, the combined effect of Ti and F in improving the dehydrogenation properties of MgH 2 is superior to that of pure Ti. These results provide a reasonable explanation for experimental observations. Analysis of electronic structures suggests the enhanced dehydrogenation properties of doped MgH 2 can be attributed to the weakened bonding interactions between Mg and H due to foreign species doping.

Radiation induced microstructural evolution in ferritic/martensitic steels

International Nuclear Information System (INIS)

Kohno, Y.; Kohyama, A.; Asakura, K.; Gelles, D.S.

1993-01-01

R and D of ferritic/martensitic steels as structural materials for fusion reactor is one of the most important issues of fusion technology. The efforts to characterize microstructural evolution under irradiation in the conventional Fe-Cr-Mo steels as well as newly developed Fe-Cr-Mn or Fe-Cr-W low activation ferritic/ martensitic steels have been continued. This paper provides some of the recent results of heavy irradiation effects on the microstructural evolution of ferritic/martensitic steels neutron irradiated in the FFTF/MOTA (Fast Flux Test Facility/Materials Open Test Assembly). Materials examined are Fe-10Cr-2Mo dual phase steel (JFMS: Japanese Ferritic/Martensitic Steel), Fe-12Cr-XMn-1Mo manganese stabilized martensitic steels and Fe-8Cr-2W Tungsten stabilized low activation martensitic steel (F82H). JFMS showed excellent void swelling resistance similar to 12Cr martensitic steel such as HT-9, while the manganese stabilized steels and F82H showed less void swelling resistance with small amount of void swelling at 640-700 K (F82H: 0.14% at 678 K). As for irradiation response of precipitate behavior, significant formation of intermetallic χ phase was observed in the manganese stabilized steels along grain boundaries which is though to cause mechanical property degradation. On the other hand, precipitates identified were the same type as those in unirradiated condition in F82H with no recognition of irradiation induced precipitates, which suggested satisfactory mechanical properties of F82H after the irradiation. (author)

Positron annihilation lifetime measurements of austenitic stainless and ferritic/martensitic steels irradiated in the SINQ target irradiation program

Science.gov (United States)

Sato, K.; Xu, Q.; Yoshiie, T.; Dai, Y.; Kikuchi, K.

2012-12-01

Titanium-doped austenitic stainless steel (JPCA) and reduced activated ferritic/martensitic steel (F82H) irradiated with high-energy protons and spallation neutrons were investigated by positron annihilation lifetime measurements. Subnanometer-sized (steel, the positron annihilation lifetime of the bubbles decreased with increasing irradiation dose and annealing temperature because the bubbles absorb additional He atoms. In the case of JPCA steel, the positron annihilation lifetime increased with increasing annealing temperature above 773 K, in which case the dissociation of complexes of vacancy clusters with He atoms and the growth of He bubbles was detected. He bubble size and density were also discussed.

Optical and magneto-optical properties of the electron-doped and hole-doped C{sub 82} crystal

Energy Technology Data Exchange (ETDEWEB)

Rostampour, E., E-mail: el_rostampour@yahoo.com [Plasma Physics Research Center, Science and Research Branch, Islamic Azad University, Tehran (Iran, Islamic Republic of); Koohi, A. [Plasma Physics and Nuclear Fusion Research School, Nuclear Science and Technology Research Institute, AEOI, Tehran (Iran, Islamic Republic of)

2015-01-15

The optical and magnetic properties of the doped C{sub 82} crystal have been investigated by Su–Schrieffer–Heeger (SSH) model, which is based on the Ewald method. When the C{sub 82} molecule is doped with one electron (or hole), a single electron is remained in the energy level that affects the optical and magnetic properties of the C{sub 82} crystal. The lattice and electronic structures of C{sub 82} changed with doping electron (or hole) in the molecule of C{sub 82}. Therefore, polarons are predicted in doped fullerenes. The obtained results showed that the dielectric tensor of the C{sub 82} crystal increased with doping electron (or hole) in the molecule of C{sub 82}. The spectral shapes of the dielectric tensor, circular dichroism and birefringence coefficient of the C{sub 82} crystal turn out to be determined mainly by the geometrical distributions of the pentagons in the fullerene structures.

Mechanical properties and microstructure of F-82H welded joints using CO{sub 2} laser beam

Energy Technology Data Exchange (ETDEWEB)

Yamanouchi, N.; Shiba, K.

1996-10-01

The laser welding of F-82H was successfully conducted. The heat affected zone of the welding, was about 21 mm width. It was quite adequate to make small specimens, such as SS-3 type sheet tensile specimen.

Microstructure and mechanical property in heat affected zone (HAZ in F82H jointed with SUS316L by fiber laser welding

Directory of Open Access Journals (Sweden)

S. Kano

2016-12-01

Full Text Available This study investigates the microstructure and mechanical property in heat affected zone (HAZ between F82H and SUS316L jointed by 4 kW fiber laser welding at different parameters such as laser scan rate and beam position. OM/FE-SEM observation, EPMA analysis and nano-indentation hardness test were utilized to characterize the microstructure and evaluate the mechanical property. Results show that the HAZ width is dependent on the welding condition. The precipitation of M23C6 particle in HAZ is found to be closely related to the distance from WM/HAZ interface. Decrease in Cr and C concentration in M23C6 depended on the welding condition; the decrease was relatively milder in the case of shifting the beam position to SUS side. Furthermore, the rapid increment in nano-indentation hardness, i.e. ≈2500 MPa, at HAZ/F82H interface was observed regardless of welding parameters. The temperatures at HAZ/F82H interface were estimated from Cr and C concentration change of M23C6 by EPMA. It was revealed that the temperature of HAZ/F82H interface increased with increasing HAZ width, and that the presence of over-tempered HAZ (THAZ region is confirmed only in the specimens welded right on the F82H/SUS interface (no-shift at the laser scan rate of 3 m/min.

Thermal and mechanical behaviour of the reduced-activation-ferritic-martensitic steel EUROFER

International Nuclear Information System (INIS)

Lindau, R.; Moeslang, A.; Schirra, M.

2002-01-01

Reduced activation ferritic/martensitic (RAFM) steels are being considered for structural application in potential fusion energy systems. Based on the substantial experience with RAFM developmental steels of OPTIFER type, an industrial 3.5 tons batch of a 9CrWVTa-RAFM steel, called EUROFER 97 had been specified and ordered. A characterisation programme has been launched to determine the relevant mechanical and physical-metallurgical properties in order to qualify the steel for fusion application. The hardening, tempering and transformation behaviour of EUROFER is in good agreement with that of other RAFM-steels like OPTIFER and the Japanese industrial scale heat F82H mod. Tensile tests, performed between RT and 750 deg. C, show comparable strength and ductility values that are not strongly affected by different heat treatments and ageing at 580 and 600 deg. C up to 3300 h. Impact bending tests indicate a superior ductile to brittle transition temperature (DBTT) of EUROFER in the as-received condition compared with that of F82H mod. Creep tests between 450 and 650 deg. C up to test times of 15000 h reveal a creep strength similar to other RAFM steels like OPTIFER and F82H mod. EUROFER shows a good low-cycle fatigue behaviour with longer lifetimes than F82H mod. The deformation and softening behaviour is similar

Mechanical properties of F82H plates with different thicknesses

Energy Technology Data Exchange (ETDEWEB)

Sakasegawa, Hideo, E-mail: sakasegawa.hideo@jaea.go.jp; Tanigawa, Hiroyasu

2016-11-01

Highlights: • Mass effect, homogeneity, and anisotropy in mechanical properties were studied. • Thickness dependence of tensile property was not observed. • Thickness dependence of Charpy impact property was observed. • Appropriate mechanical properties were obtained using an electric furnace. - Abstract: Fusion DEMO reactor requires over 11,000 tons of reduced activation ferritic/martensitic steel and it is indispensable to develop the manufacturing technology for producing large-scale components of DEMO blanket with appropriate mechanical properties. This is because mechanical properties are generally degraded with increasing production volume. In this work, we focused mechanical properties of F82H–BA12 heat which was melted in a 20 tons electric arc furnace. Plates with difference thicknesses from 18 to 100 mm{sup t} were made from its ingot through forging and hot-rolling followed by heat treatments. Tensile and Charpy impact tests were then performed on plates focusing on their homogeneity and anisotropy. From the result, their homogeneity and anisotropy were not significant. No obvious differences were observed in tensile properties between the plates with different thicknesses. However, Charpy impact property changed with increasing plate thickness, i.e. the ductile brittle transition temperature of a 100 mm{sup t} thick plate was higher than that of the other thinner plates.

Superior hydrogen storage kinetics of MgH2 nanoparticles doped with TiF3

International Nuclear Information System (INIS)

Xie, L.; Liu, Y.; Wang, Y.T.; Zheng, J.; Li, X.G.

2007-01-01

MgH 2 nanoparticles were obtained by hydriding ultrafine magnesium particles which were prepared by hydrogen plasma-metal reaction. The X-ray diffraction (XRD) and transmission electron microscopy (TEM) results show that the obtained sample is almost pure MgH 2 phase, without residual magnesium and with an average particle size of ∼300 nm. Milled with 5 wt.% TiF 3 as a doping precursor in a hydrogen atmosphere, the sample desorbed 4.5 wt.% hydrogen in 6 min under an initial hydrogen pressure of ∼0.001 bar at 573 K and absorbed 4.2 wt.% hydrogen in 1 min under ∼20 bar hydrogen at room temperature. Compared with MgH 2 micrometer particles doped with 5 wt.% TiF 3 under the same conditions as the MgH 2 nanoparticles, it is suggested that decrease of particle size is beneficial for enhancing absorption capacity at low temperatures, but has no effect on desorption. In addition, the catalyst was mainly responsible for improving the sorption kinetics and its catalytic mechanism is discussed

Effects of thermal aging on the mechanical behavior of F82H weldments

International Nuclear Information System (INIS)

Alamo, A.; Castaing, A.; Fontes, A.; Wident, P.

2000-01-01

The objective of this work is to characterize the mechanical behavior of F82H weldments, which were produced by tungsten inert gas (TIG) and electron beam (EB) processes. Tensile and impact properties were determined for both types of welds in the as-received condition and after thermal aging for 10 000 h at 400 deg. C and 550 deg. C. The mechanical properties of TIG welds and their evolution during aging is quite similar in the base metal (BM). The main difference was given by the impact energy level (upper shelf energy (USE)) of TIG joints, which is about 60% of the BM. EB welds were delivered without post-weld heat treatment. Very scattered results were obtained, particularly for impact properties

Superior hydrogen storage kinetics of MgH{sub 2} nanoparticles doped with TiF{sub 3}

Energy Technology Data Exchange (ETDEWEB)

Xie, L. [Beijing National Laboratory for Molecular Sciences (BNLMS), State Key Laboratory of Rare Earth Materials Chemistry and Applications, College of Chemistry and Molecular Engineering, Peking University, Beijing 100871 (China); Liu, Y. [Beijing National Laboratory for Molecular Sciences (BNLMS), State Key Laboratory of Rare Earth Materials Chemistry and Applications, College of Chemistry and Molecular Engineering, Peking University, Beijing 100871 (China); Wang, Y.T. [Beijing National Laboratory for Molecular Sciences (BNLMS), State Key Laboratory of Rare Earth Materials Chemistry and Applications, College of Chemistry and Molecular Engineering, Peking University, Beijing 100871 (China); Zheng, J. [Beijing National Laboratory for Molecular Sciences (BNLMS), State Key Laboratory of Rare Earth Materials Chemistry and Applications, College of Chemistry and Molecular Engineering, Peking University, Beijing 100871 (China); Li, X.G. [Beijing National Laboratory for Molecular Sciences (BNLMS), State Key Laboratory of Rare Earth Materials Chemistry and Applications, College of Chemistry and Molecular Engineering, Peking University, Beijing 100871 (China) and College of Engineering, Peking University, Beijing 100871 (China)]. E-mail: xgli@pku.edu.cn

2007-08-15

MgH{sub 2} nanoparticles were obtained by hydriding ultrafine magnesium particles which were prepared by hydrogen plasma-metal reaction. The X-ray diffraction (XRD) and transmission electron microscopy (TEM) results show that the obtained sample is almost pure MgH{sub 2} phase, without residual magnesium and with an average particle size of {approx}300 nm. Milled with 5 wt.% TiF{sub 3} as a doping precursor in a hydrogen atmosphere, the sample desorbed 4.5 wt.% hydrogen in 6 min under an initial hydrogen pressure of {approx}0.001 bar at 573 K and absorbed 4.2 wt.% hydrogen in 1 min under {approx}20 bar hydrogen at room temperature. Compared with MgH{sub 2} micrometer particles doped with 5 wt.% TiF{sub 3} under the same conditions as the MgH{sub 2} nanoparticles, it is suggested that decrease of particle size is beneficial for enhancing absorption capacity at low temperatures, but has no effect on desorption. In addition, the catalyst was mainly responsible for improving the sorption kinetics and its catalytic mechanism is discussed.

Plastic flow properties and fracture toughness characterization of unirradiated and irradiated tempered martensitic steels

International Nuclear Information System (INIS)

Spaetig, P.; Bonade, R.; Odette, G.R.; Rensman, J.W.; Campitelli, E.N.; Mueller, P.

2007-01-01

We investigate the plastic flow properties at low and high temperature of the tempered martensitic steel Eurofer97. We show that below room temperature, where the Peierls friction on the screw dislocation is active, it is necessary to modify the usual Taylor's equation between the flow stress and the square root of the dislocation density and to include explicitly the Peierls friction stress in the equation. Then, we compare the fracture properties of the Eurofer97 with those of the F82H steel. A clear difference of the fracture toughness-temperature behavior was found in the low transition region. The results indicate a sharper transition for Eurofer97 than for the F82H. Finally, the shift of the median toughness-temperature curve of the F82H steel was determined after two neutron irradiations performed in the High Flux Reactor in Petten

Creep behavior of double tempered 8% Cr-2% WVTa martensitic steel

International Nuclear Information System (INIS)

Tamura, Manabu; Shinozuka, Kei; Esaka, Hisao; Nowell, Matthew M.

2006-01-01

Creep testing was carried out at around 650degC for a martensitic 8Cr-2WVTa steel (F82H), which is a candidate alloy for the first wall of the fusion reactors of the Tokamak type. Rupture strength of the double tempered steel (F82HD) is lightly higher than that of simple tempered steel (F82HS). On the other hand, creep rate of F82HD is obviously smaller than that of F82HS in acceleration creep, though creep strain of F82HD in transition creep, where creep rate decreases with increasing strain, is larger than that of F82HS. Hardness of the crept H82HD decreases with increasing creep strain, which corresponded with the transmission electron microscopy (TEM) observation. On the contrary, X-ray diffraction and electron back-scattered diffraction pattern measurements show that fine sub-grains are created during transition creep. The creep curves were analyzed using an exponential type creep equation and the apparent activation energy, the activation volume and the pre-exponential factor were calculated as a function of creep strain. Then, these parameters were converted into two parameters, i.e. equivalent obstacle spacing (EOS) and mobile dislocation density parameter (MDDP). While EOS decreases with increasing creep strain, MDDP increases with increasing strain during transition creep. The decrease in EOS and the increase in either EOS or MDDP are rate-controlling factors in transition and acceleration creep, respectively. On the other hand, in case of F82HS, EOS increases and MDDP decreases during transition creep. In this case, the decrease in MDDP controls the creep rate during transition creep of F82HS. It is concluded that both EOS and MDDP are representative parameters of the change in substructure during creep. (author)

Positron annihilation lifetime measurements of vanadium alloy and F82H irradiated with fission and fusion neutrons

International Nuclear Information System (INIS)

Sato, K.; Inoue, K.; Yoshiie, T.; Xu, Q.; Wakai, E.; Kutsukake, C.; Ochiai, K.

2009-01-01

V-4Cr-4Ti, F82H, Ni and Cu were irradiated with fission and fusion neutrons at room temperature and 473 K. Defect structures were analyzed and compared using positron annihilation lifetime measurement, and microstructural evolution was discussed. The mean lifetime of positrons (the total amount of residual defects) increased with the irradiation dose. The effect of cascade impact was detected in Ni at room temperature. The size and the number of vacancy clusters were not affected by the displacement rate in the fission neutron irradiation at 473 K for the metals studied. The vacancy clusters were not formed in V-4Cr-4Ti irradiated at 473 K in the range of 10 -6 -10 -3 dpa. In F82H irradiated at 473 K, the defect evolution was prevented by pre-existing defects. The mean lifetime of positrons in fission neutron irradiation was longer than that in fusion neutron irradiation in V-4Cr-4Ti at 473 K. It was interpreted that more closely situated subcascades were formed in the fusion neutron irradiation and subcascades interacted with each other, and consequently the vacancy clusters did not grow larger.

Ferromagnetism in 4H-GaN polytype doped by non-magnetic light elements Li, Be, B, C, O, F, Ne, Na, and Mg: Ab-initio study

International Nuclear Information System (INIS)

Torrichi, M.; Ferhat, M.; Bouhafs, B.

2016-01-01

Using density-functional theory within the generalized-gradient approximation, we explore the magnetic behavior induced by nonmagnetic impurity X atoms, such as Li, Be, B, C, O, F, Ne, Na, and Mg on cation site in 4H-GaN polytype. The results reveal that Ne doped 4H-GaN has the highest magnetic moment of 3µ B , whereas Mg doped 4H-GaN has the lowest magnetic moment of 0.75µ B . Among the systems studied 4H-GaN doped Ne has been found to be half-metallic, whereas 4H-GaN doped F and Na are found to be nearly half-metallic. The partial density of states evidence that magnetism is achieved through a p-p like coupling between the impurity and the host 2p states. Furthermore, we inspect whether there exists a relationship between the spin-polarization and the local structure around the doping X atoms. It is found that for all the compounds studied, the total magnetic moment increases with increasing the X–N bond lengths. Interestingly, 4H-GaN:Be becomes ferromagnetic with increasing the Be–N bond length, whereas 4H-GaN:Na and 4H-GaN:F become half-metallic with increasing Na–N and F–N bond lengths. - Highlights: • The partial densities of states of 4H-GaN polytype doped light nonmagnetic elements have been investigated. • We found that 4H-GaN:Ne is half metallic. • We found that N atoms induced strong local magnetic. • We found that doping with half-filled X-s impurity states promotes ferromagnetism. • We found that doping with full-filled X-s impurity annihilates ferromagnetism.

Effect of ball milling time on the hydrogen storage properties of TiF{sub 3}-doped LiAlH{sub 4}

Energy Technology Data Exchange (ETDEWEB)

Liu, Shu-Sheng [Materials and Thermochemistry Laboratory, Dalian Institute of Chemical Physics, Chinese Academy of Sciences, 457 Zhongshan Road, Dalian, Liaoning 116023 (China); Graduate School of Chinese Academy of Sciences, Beijing 100049 (China); Sun, Li-Xian; Zhang, Yao; Zhang, Jian; Chu, Hai-Liang; Fan, Mei-Qiang; Zhang, Tao [Materials and Thermochemistry Laboratory, Dalian Institute of Chemical Physics, Chinese Academy of Sciences, 457 Zhongshan Road, Dalian, Liaoning 116023 (China); Xu, Fen [Faculty of Chemistry and Chemical Engineering, Liaoning Normal University, Dalian 116029 (China); Song, Xiao-Yan [College of Materials Science and Engineering, Key Laboratory of Advanced Functional Materials, Chinese Education Ministry, Beijing University of Technology, Beijing 100124 (China); Grolier, Jean Pierre [Laboratory of Thermodynamics of Solutions and Polymers, Blaise Pascal University, 24 Avenue des Landais, 63177-Aubiere Cedex (France)

2009-10-15

In the present work, the catalytic effect of TiF{sub 3} on the dehydrogenation properties of LiAlH{sub 4} has been investigated. Decomposition of LiAlH{sub 4} occurs during ball milling in the presence of 4 mol% TiF{sub 3}. Different ball milling times have been used, from 0.5 h to 18 h. With ball milling time increasing, the crystallite sizes of LiAlH{sub 4} get smaller (from 69 nm to 43 nm) and the dehydrogenation temperature becomes lower (from 80 C to 60 C). Half an hour ball milling makes the initial dehydrogenation temperature of doped LiAlH{sub 4} reduce to 80 C, which is 70 C lower than as-received LiAlH{sub 4}. About 5.0 wt.% H{sub 2} can be released from TiF{sub 3}-doped LiAlH{sub 4} after 18 h ball milling in the range of 60 C-145 C (heating rate 2 C min{sup -1}). TiF{sub 3} probably reacts with LiAlH{sub 4} to form the catalyst, TiAl{sub 3}. The mechanochemical and thermochemical reactions have been clarified. However, the rehydrogenation of LiAlH{sub 4}/Li{sub 3}AlH{sub 6} can not be realized under 95 bar H{sub 2} in the presence of TiF{sub 3} because of their thermodynamic properties. (author)

Electrospark doping of steel with tungsten

International Nuclear Information System (INIS)

Denisova, Yulia; Shugurov, Vladimir; Petrikova, Elizaveta; Seksenalina, Malika; Ivanova, Olga; Ikonnikova, Irina; Kunitsyna, Tatyana; Vlasov, Victor; Klopotov, Anatoliy; Ivanov, Yuriy

2016-01-01

The paper is devoted to the numerical modeling of thermal processes and the analysis of the structure and properties of the surface layer of carbon steel subjected to electrospark doping with tungsten. The problem of finding the temperature field in the system film (tungsten) / substrate (iron) is reduced to the solution of the heat conductivity equation. A one-dimensional case of heating and cooling of a plate with the thickness d has been considered. Calculations of temperature fields formed in the system film / substrate synthesized using methods of electrospark doping have been carried out as a part of one-dimensional approximation. Calculations have been performed to select the mode of the subsequent treatment of the system film / substrate with a high-intensity pulsed electron beam. Authors revealed the conditions of irradiation allowing implementing processes of steel doping with tungsten. A thermodynamic analysis of phase transformations taking place during doping of iron with tungsten in equilibrium conditions has been performed. The studies have been carried out on the surface layer of the substrate modified using the method of electrospark doping. The results showed the formation in the surface layer of a structure with a highly developed relief and increased strength properties

Electrospark doping of steel with tungsten

Energy Technology Data Exchange (ETDEWEB)

Denisova, Yulia, E-mail: yukolubaeva@mail.ru; Shugurov, Vladimir, E-mail: shugurov@opee.hcei.tsc.ru [Institute of High-Current Electronics of the Siberian Branch of the Russian Academy of Sciences, 634055, Russia, Tomsk, 2/3 Akademicheskiy Ave (Russian Federation); Petrikova, Elizaveta, E-mail: elizmarkova@yahoo.com [Institute of High-Current Electronics of the Siberian Branch of the Russian Academy of Sciences, 634055, Russia, Tomsk, 2/3 Akademicheskiy Ave (Russian Federation); National Research Tomsk State University, 36 Lenin Str. Tomsk, 634050 (Russian Federation); Seksenalina, Malika, E-mail: sportmiss@bk.ru [National Research Tomsk Polytechnic University, 30 Lenin Str. Tomsk, 634050 (Russian Federation); Ivanova, Olga, E-mail: ivaov@mail.ru; Ikonnikova, Irina, E-mail: irinaikonnikova@yandex.ru [Tomsk State University of Architecture and Building, 2 Solyanaya Sq. Tomsk, 634003 (Russian Federation); Kunitsyna, Tatyana, E-mail: kma11061990@mail.ru; Vlasov, Victor, E-mail: rector@tsuab.ru [National Research Tomsk Polytechnic University, 30 Lenin Str. Tomsk, 634050 (Russian Federation); Tomsk State University of Architecture and Building, 2 Solyanaya Sq. Tomsk, 634003 (Russian Federation); Klopotov, Anatoliy, E-mail: klopotovaa@tsuab.ru [National Research Tomsk State University, 36 Lenin Str. Tomsk, 634050 (Russian Federation); Tomsk State University of Architecture and Building, 2 Solyanaya Sq. Tomsk, 634003 (Russian Federation); Ivanov, Yuriy, E-mail: yufi55@mail.ru [Institute of High-Current Electronics of the Siberian Branch of the Russian Academy of Sciences, 634055, Russia, Tomsk, 2/3 Akademicheskiy Ave (Russian Federation); National Research Tomsk State University, 36 Lenin Str. Tomsk, 634050 (Russian Federation); National Research Tomsk Polytechnic University, 30 Lenin Str. Tomsk, 634050 (Russian Federation)

2016-01-15

The paper is devoted to the numerical modeling of thermal processes and the analysis of the structure and properties of the surface layer of carbon steel subjected to electrospark doping with tungsten. The problem of finding the temperature field in the system film (tungsten) / substrate (iron) is reduced to the solution of the heat conductivity equation. A one-dimensional case of heating and cooling of a plate with the thickness d has been considered. Calculations of temperature fields formed in the system film / substrate synthesized using methods of electrospark doping have been carried out as a part of one-dimensional approximation. Calculations have been performed to select the mode of the subsequent treatment of the system film / substrate with a high-intensity pulsed electron beam. Authors revealed the conditions of irradiation allowing implementing processes of steel doping with tungsten. A thermodynamic analysis of phase transformations taking place during doping of iron with tungsten in equilibrium conditions has been performed. The studies have been carried out on the surface layer of the substrate modified using the method of electrospark doping. The results showed the formation in the surface layer of a structure with a highly developed relief and increased strength properties.

Water corrosion of F82H-modified in simulated irradiation conditions by heat treatment

International Nuclear Information System (INIS)

Lapena, J.; Blazquez, F.

2000-01-01

This paper presents results of testing carried out on F82H in water at 260 deg. C with 2 ppm H 2 and the addition of 0.27 ppm Li in the form of LiOH. Uniform corrosion tests have been carried out on as-received material and on specimens from welded material [TIG and electron beam (EB)]. Stress corrosion cracking (SCC) tests have been carried out in as-received material and in material heat treated to simulate neutron irradiation hardening (1075 deg. C/30' a.c. and 1040 deg. C/30' + 625 deg. C/1 h a.c.) with hardness values of 405 and 270 HV30, respectively. Results for uniform corrosion after 2573 h of testing have shown weight losses of about 60 mg/dm 2 . Compact tension (CT) specimens from the as-received material tested under constant load have not experienced crack growth. However, in the simulated irradiation conditions for a stress intensity factor between 40 and 80 MPa√m, crack growth rates of about 7x10 -8 m/s have been measured

Enhancement of H2-sensing Properties of F-doped SnO2 Sensorby Surface Modification with SiO2

Directory of Open Access Journals (Sweden)

S. P. Khatkar

2006-05-01

Full Text Available Effects of surface chemical modification with sodium silicate on the gas-sensingproperties of F-doped SnO2 gas sensor designed and fabricated employing micro-electromechanical system (MEMS technology were investigated. Gas sensing properties of thesensor were checked against combustible gases like H2, CO, CH4 and C3H8 at a heatervoltage of 0.7 V. The H2 sensitivity of the surface modified F-doped SnO2 micro sensormarkedly increased and reached S = 175 which was found to be about 40 times more thanthat of unmodified sensor (S = ~ 4.2. The increase in the sensitivity is discussed in terms ofincreased resistivity and reduced permeation of gaseous oxygen into the underlying sensinglayer due to the surface modification of the sensor. The present micro-hydrogen sensor withenhanced sensitivity due to SiO2 incorporation is a low energy consuming portable sensormodule that can be mass-produced using MEMS technology at low cost.

46 CFR 54.25-25 - Welding of quenched and tempered steels (modifies UHT-82).

Science.gov (United States)

2010-10-01

... 46 Shipping 2 2010-10-01 2010-10-01 false Welding of quenched and tempered steels (modifies UHT-82... ENGINEERING PRESSURE VESSELS Construction With Carbon, Alloy, and Heat Treated Steels § 54.25-25 Welding of quenched and tempered steels (modifies UHT-82). (a) The qualification of welding procedures, welders, and...

Microstructure Changes of Aluminum Titanate Refractory Doped SiO{sub 2} and ZrO{sub 2} in Molten Steel

Energy Technology Data Exchange (ETDEWEB)

Kim, Dami; Kim, Hyung-Tae; Ryu, Sung-Soo; Kim, Hyeong-Jun [Korea Institute of Ceramic Engineering and Technology, Bucheon (Korea, Republic of)

2015-02-15

Aluminum titanate (AT) ceramics has high potential as alloy casting refractory materials due to their good thermal shock resistance which results from their low coefficient of thermal expansion. In a previous study, AT doped SiO{sub 2} and ZrO{sub 2} were developed to achieve stability and mechanical strength at high temperature. In this work, the changes of microstructure of AT doped SiO{sub 2} and ZrO{sub 2} were investigated in molten steel. A finger rotating test of sintered AT was carried out at 1300 ℃ for 30 min, 1 h, 2 h, and 3 h. Even if there was no reaction between AT and molten steel, a new surface was formed, followed by the decomposition of AT by the heat from molten steel, which was dominantly constituted of Al and Si due to decomposition of AT and Mullite phases. Some of the new surface layer was found to have been eroded by fluctuations of the molten steel.

Development of an extensive database of mechanical properties for Reduced Activation Ferritic/Martensitic Steels

International Nuclear Information System (INIS)

Tanigawa, H.; Shiba, K.; Ando, M.; Wakai, E.; Jitsukawa, S.; Hirose, T.; Kasada, R.; Kimura, A.; Kohyama, A.; Kohno, Y.; Klueh, R.L.; Sokolov, M.; Stoller, R.; Zinklek, S.; Yamamoto, T.; Odette, G.; Kurtz, R.J.

2007-01-01

Full text of publication follows: Reduced activation ferritic/martensitic steels (RAFMs) are recognized as the primary candidate structural materials for fusion blanket systems, as they have been developed based on massive industrial experience of ferritic/martensitic steel replacing Mo and Nb of high chromium heat resistant martensitic steels (such as modified 9Cr-1Mo) with W and Ta, respectively. F82H (8Cr-2W-0.2V-0.04Ta-0.1C) and JLF-1 (9Cr-2W-0.2V-0.08Ta-0.1C) are RAFMs, which have been developed and studied in Japan and the various effects of irradiation were reported. F82H is designed with emphasis on high temperature property and weldablility, and was provided and evaluated in various countries as a part of the IEA fusion materials development collaboration. The Japan/US collaboration program also has been conducted with the emphasis on heavy irradiation effects of F82H, JLF-1 and ORNL9Cr2WVTa over the past two decades using Fast Flux Testing Facility (FFTF) of PNNL and High Flux Isotope Reactor (HFIR) of ORNL, and the irradiation condition of the irradiation capsules of those reactors were precisely controlled by the well matured capsule designing and instrumentation. Now, among the existing database for RAFMs the most extensive one is that for F82H. The objective of this paper is to review the database status of RAFMs, mainly on F82H, to identify the key issues for the future development of database. Tensile, fracture toughness, creep and fatigue properties and microstructural studies before and after irradiation are summarized. (authors)

Development of an extensive database of mechanical properties for Reduced Activation Ferritic/Martensitic Steels

Energy Technology Data Exchange (ETDEWEB)

Tanigawa, H.; Shiba, K.; Ando, M.; Wakai, E.; Jitsukawa, S. [Japan Atomic Energy Agency, Tokai-mura, Naga-gun, Ibaraki-ken (Japan); Hirose, T. [Blanket Engineering Group, Japan Atomic Energy Agency, Naka, Ibaraki (Japan); Kasada, R.; Kimura, A.; Kohyama, A. [Kyoto Univ., lnstitute of Advanced Energy (Japan); Kohno, Y. [Muroran Institute of Technology, Muroran, Hokkaido (Japan); Klueh, R.L. [0ak Ridge Noational Laboratory, TN (United States); Sokolov, M.; Stoller, R.; Zinklek, S. [0ak Ridge Noational Laboratory, Materials Science and Technology Div., TN (United States); Yamamoto, T.; Odette, G. [UCSB, Dept. of Chemical Engineering UCSB, Santa-Barbara (United States); Kurtz, R.J. [Pacifie Northwest National Laboratory, Richland WA (United States)

2007-07-01

Full text of publication follows: Reduced activation ferritic/martensitic steels (RAFMs) are recognized as the primary candidate structural materials for fusion blanket systems, as they have been developed based on massive industrial experience of ferritic/martensitic steel replacing Mo and Nb of high chromium heat resistant martensitic steels (such as modified 9Cr-1Mo) with W and Ta, respectively. F82H (8Cr-2W-0.2V-0.04Ta-0.1C) and JLF-1 (9Cr-2W-0.2V-0.08Ta-0.1C) are RAFMs, which have been developed and studied in Japan and the various effects of irradiation were reported. F82H is designed with emphasis on high temperature property and weldablility, and was provided and evaluated in various countries as a part of the IEA fusion materials development collaboration. The Japan/US collaboration program also has been conducted with the emphasis on heavy irradiation effects of F82H, JLF-1 and ORNL9Cr2WVTa over the past two decades using Fast Flux Testing Facility (FFTF) of PNNL and High Flux Isotope Reactor (HFIR) of ORNL, and the irradiation condition of the irradiation capsules of those reactors were precisely controlled by the well matured capsule designing and instrumentation. Now, among the existing database for RAFMs the most extensive one is that for F82H. The objective of this paper is to review the database status of RAFMs, mainly on F82H, to identify the key issues for the future development of database. Tensile, fracture toughness, creep and fatigue properties and microstructural studies before and after irradiation are summarized. (authors)

Evaluation of toughness degradation by small punch (SP) tests for neutron irradiated structural steels

International Nuclear Information System (INIS)

Misawa, Toshihei; Hamaguchi, Yoshikazu; Kimura, Akihiko; Eto, Motokuni; Suzuki, Masahide; Nakajima, Nobuya.

1992-01-01

The small punch (SP) test as one of the useful small specimen testing technique (SSTT) has been developed to evaluate the fracture toughness, ductile-brittle transition temperature (DBTT) and tensile properties for neutron irradiated structural materials. The SP tests using the miniaturized specimens of φ3 mm TEM disk and 10 mm 2 coupon were performed for six kinds of ferritic steels of F-82, F-82H, HT-9, JFMS, 2.25-1Mo and SQV2A. It was shown that the temperature dependence of SP fracture energies with scatter in miniaturized testing can give reliable information on the DBTT by use of the statistical analysis based on the Weibull distribution. A good correlation between the DBTT of the SP tests and that of the standard CVN test has been obtained for the various nuclear ferritic steels. The SP test was performed for cryogenic austenitic steels as a way of evaluating elastic-plastic fracture toughness, J IC , on the basis of a universal empirical relationship between J IC and SP equivalent fracture strain, ε-bar qf . The SP testing using the neutron irradiated specimens of 2.25Cr-1Mo, F-82, F-82H and HT-9 steels was successfully applied and presented the neutron radiation induced changes on the DBTT, fracture toughness and tensile properties. (author)

Effects of helium on ductile brittle transition behavior of reduced activation ferritic steels after high concentration he implantation at high temperature

Energy Technology Data Exchange (ETDEWEB)

Hasegawa, A.; Ejiri, M.; Nogami, S.; Ishiga, M.; Abe, K. [Tohoku Univ., Dept. of Quantum Science and Energy Engr, Sendai (Japan); Kasada, R.; Kimura, A. [Kyoto Univ., Institute of Advanced Energy (Japan); Jitsukawa, S. [Japan Atomic Energy Agency, Tokai-mura, Naga-gun, Ibaraki-ken (Japan)

2007-07-01

Full text of publication follows: Influence of Helium (He) on fracture behavior of reduced activation ferritic/martensitic steels including Oxide Dispersion Strengthening (ODS) steels and F82H were examined. To study the He effects on fracture behavior of these steels after He bubble formation conditions, higher concentration of He implantation at around 550 C were performed and examined the relationship between microstructure evolution and fracture behavior of the steels. The 1.5CVN mini size Charpy specimens were used to evaluate impact test behavior. Reduced activation ferritic ODS steels, 9Cr-ODS and 12Cr-ODS steels were examine. F82H was also examined as reference material. Helium implantation was performed by a cyclotron of Tohoku University with a beam of 50 MeV {alpha}-particles at temperature around 550 C. A tandem-type energy degrader system was used to implant He into the specimen from the irradiated surface to the range of 50 MeV {alpha}-particles, that was about 380 {mu}m in iron. Implanted He concentration were about 1000 appm. Charpy impact test was performed using a instrumented impact test apparatus in Oarai branch of IMR, Tohoku University. Analyses of absorbed energy change and fracture surface were carried out. Vickers hardness test was also carried out on He implanted area of the 1.5CVN specimen to estimate irradiation hardening. Microstructural observation was performed by TEM. In the case of F82H, DBTT increased by the 1000 appm He implantation condition was about 80 C and grain boundary fracture surface was only observed in the He implanted area of all the ruptured specimens in brittle manner. On the other hand, DBTT shift and fracture mode change of He implanted 9Cr-ODS steel was not observed after He implantation. Microstructural observation showed that He bubble formation on the lath boundaries and grain boundaries were significant in F82H, but the bubble segregation on grain boundary in ODS steel was not apparent. The bubble formation

Corrosion protection of AISI 1018 steel using Co-doped TiO_2/polypyrrole nanocomposites in 3.5% NaCl solution

International Nuclear Information System (INIS)

Ladan, Magaji; Basirun, Wan Jeffrey; Kazi, Salim Newaz; Rahman, Fariza Abdul

2017-01-01

A polypyrrole nanocomposites (PPy NTCs) have been effectively synthesized in the presence of TiO_2 and Co-doped TiO_2 nanoparticles (NPs) by an in situ chemical oxidative polymerization. Field Emission Scanning Electron Microscopy and Transmission Electron Microscopy revealed a tube shape structure of the PPy. The TEM results confirmed that the nanocomposite size of Co-doped TiO_2/PPy NTCs was smaller than TiO_2/PPy NTCs thereby increasing the interaction between the PPy nanotube and the AISI steel surface. The corrosion performance of the coatings was evaluated by electrochemical impedance spectroscopy (EIS) and potentiodynamic polarization measurements in 3.5% NaCl solution. The EIS results show that the log |Z| of AISI 1018 coated with Co-doped TiO_2/PPy NTCs and TiO_2/PPy NTCs reached about 8.2 and 6.0 respectively after 30 days of exposure in 3.5% NaCl solution. This is likely due to the increased surface area of the PPy synthesized in the presence of Co-doped TiO_2 NPs. The EIS results are confirmed by the potentiodynamic polarization and open circuit potential values of the Co-doped TiO_2/PPy which indicated little changes between 1 and 30 days of exposure which confirms the protection ability of this coating. . It is evident that the presence of Co-doped TiO_2 NPs can enhance the resistance against corrosion at the steel/electrolyte interface. - Highlights: • Polymerization of pyrrole monomer in the presence of Co-doped TiO_2 decreases the size of the polypyrrole nanotube (PPy NT). • The corrosion protection increases with the increase in PPy NT dispersion. • The corrosion resistance of steel coated with Co-doped TiO_2/PPy NTCs is considerably higher. • TiO_2/PPy with Co doping reduces the charge transfer across the electrolyte/AISI 1018 steel interface.

Synthesis, characterization of CaF2 doped silicate glass-ceramics.

Science.gov (United States)

Riaz, Madeeha; Zia, Rehana; Mirza, Ambreen; Hussain, Tousif; Bashir, Farooq; Anjum, Safia

2017-06-01

This paper reports the fabrication and characterization of silicate glass-ceramics doped with (0-12mol%) CaF 2 . TGA-DSC analysis was carried out to determine the crystallization temperature and stability of glass measured by two glass parameters; Hruby parameter K H =(T x -T g )/(T L -T x ) and Weinberg parameter K W =(T c -T g )/T L . It was found that with CaF 2 doping improved sinterability at low temperature and provided stability to the glass. The XRD pattern exhibits a single phase of combeite and doping of CaF 2 cause increase in crystallite size. Microstructure of samples was also improved with CaF 2 addition, pores were significantly reduced. After 15days immersion in simulated body fluid all samples developed apatite layer onto its surface. Hence, the addition of CaF 2 provided bioactive glass-ceramic material having a low processing temperature. Copyright © 2017 Elsevier B.V. All rights reserved.

Corrosion protection of AISI 1018 steel using Co-doped TiO{sub 2}/polypyrrole nanocomposites in 3.5% NaCl solution

Energy Technology Data Exchange (ETDEWEB)

Ladan, Magaji, E-mail: ladanmagaji@yahoo.com [Department of Chemistry, Faculty of Science, University of Malaya, Kuala Lumpur, 50603 (Malaysia); Department of Pure and Industrial Chemistry, Bayero University Kano (Nigeria); Basirun, Wan Jeffrey, E-mail: jeff@um.edu.my [Department of Chemistry, Faculty of Science, University of Malaya, Kuala Lumpur, 50603 (Malaysia); Institute of Nanotechnology and Catalysis (NanoCat), University of Malaya, Kuala Lumpur, 50603 (Malaysia); Kazi, Salim Newaz; Rahman, Fariza Abdul [Department of Mechanical Engineering, Faculty of Engineering, University of Malaya, Kuala Lumpur, 50603 (Malaysia)

2017-05-01

A polypyrrole nanocomposites (PPy NTCs) have been effectively synthesized in the presence of TiO{sub 2} and Co-doped TiO{sub 2} nanoparticles (NPs) by an in situ chemical oxidative polymerization. Field Emission Scanning Electron Microscopy and Transmission Electron Microscopy revealed a tube shape structure of the PPy. The TEM results confirmed that the nanocomposite size of Co-doped TiO{sub 2}/PPy NTCs was smaller than TiO{sub 2}/PPy NTCs thereby increasing the interaction between the PPy nanotube and the AISI steel surface. The corrosion performance of the coatings was evaluated by electrochemical impedance spectroscopy (EIS) and potentiodynamic polarization measurements in 3.5% NaCl solution. The EIS results show that the log |Z| of AISI 1018 coated with Co-doped TiO{sub 2}/PPy NTCs and TiO{sub 2}/PPy NTCs reached about 8.2 and 6.0 respectively after 30 days of exposure in 3.5% NaCl solution. This is likely due to the increased surface area of the PPy synthesized in the presence of Co-doped TiO{sub 2} NPs. The EIS results are confirmed by the potentiodynamic polarization and open circuit potential values of the Co-doped TiO{sub 2}/PPy which indicated little changes between 1 and 30 days of exposure which confirms the protection ability of this coating. . It is evident that the presence of Co-doped TiO{sub 2} NPs can enhance the resistance against corrosion at the steel/electrolyte interface. - Highlights: • Polymerization of pyrrole monomer in the presence of Co-doped TiO{sub 2} decreases the size of the polypyrrole nanotube (PPy NT). • The corrosion protection increases with the increase in PPy NT dispersion. • The corrosion resistance of steel coated with Co-doped TiO{sub 2}/PPy NTCs is considerably higher. • TiO{sub 2}/PPy with Co doping reduces the charge transfer across the electrolyte/AISI 1018 steel interface.

Corrosion rate of parent and weld materials of F82H and JPCA steels under LBE flow with active oxygen control at 450 and 500 deg. C

International Nuclear Information System (INIS)

Kikuchi, Kenji; Kamata, Kinya; Ono, Mikinori; Kitano, Teruaki; Hayashi, Kenichi; Oigawa, Hiroyuki

2008-01-01

Corrosion behavior of parent and weld materials of F82H and JPCA was studied in the circulating LBE loop under impinging flow. These are candidate materials for Japanese Accelerator Driven System (ADS) beam windows. Maximum temperatures were kept to 450 and 500 deg. C with 100 deg. C constant temperature difference. Main flow velocity was 0.4-0.6 m/s in every case. Oxygen concentration was controlled to 2-4 x 10 -5 mass% although there was one exception. Testing time durations were 500-3000 h. Round bar type specimens were put in the circular tube of the loop. An electron beam weld in the middle of specimens was also studied. Optical microscopy, electron microscopy, X-ray element analyses and X-ray diffraction were used to investigate corrosion in these materials. Consequently corrosion depth and stability of those oxide layers were characterized based on the analyses. For a long-term behavior a linear law is recommended to predict corrosion in the ADS target design

Protective immunity induced in mice by F8.1 and F8.2 antigens purified from Schistosoma mansoni eggs

Directory of Open Access Journals (Sweden)

Claudia Campra Ferreira

1998-01-01

Full Text Available Schistosoma mansoni soluble egg antigens (SEA were fractionated by isoelectric focusing, resulting in 20 components, characterized by pH, absorbance and protein concentration. The higher absorbance fractions were submitted to electrophoresis, and fraction 8 (F8 presented a specific pattern of bands on its isoelectric point. Protein 3 was observed only on F8, and so, it was utilized to rabbit immunization, in order to evaluate its capacity of inducing protective immunity. IgG antibodies from rabbit anti-F8 serum were coupled to Sepharose, and used to obtain the specific antigen by affinity chromatography. This antigen, submitted to electrophoresis, presented two proteic bands (F8.1 and F8.2, which were transferred to nitrocellulose membrane (PVDF and sequenciated. The homology of F8.2 to known proteins was determined using the Basic Local Alignment Search Tool program (BLASTp. Significant homologies were obtained for the rabbit cytosolic Ca2+ uptake inhibitor, and for the bird a1-proteinase inhibitor. Immunization of mice with F8.1 and F8.2, in the presence of Corynebacterium parvum and Al(OH3 as adjuvant, induced a significant protection degree against challenge infection, as observed by the decrease on worm burden recovered from portal system.

Technical issues of reduced activation ferritic/martensitic steels for fabrication of ITER test blanket modules

International Nuclear Information System (INIS)

Tanigawa, H.; Hirose, T.; Shiba, K.; Kasada, R.; Wakai, E.; Serizawa, H.; Kawahito, Y.; Jitsukawa, S.; Kimura, A.; Kohno, Y.; Kohyama, A.; Katayama, S.; Mori, H.; Nishimoto, K.; Klueh, R.L.; Sokolov, M.A.; Stoller, R.E.; Zinkle, S.J.

2008-01-01

Reduced activation ferritic/martensitic steels (RAFMs) are recognized as the primary candidate structural materials for fusion blanket systems. The RAFM F82H was developed in Japan with emphasis on high-temperature properties and weldability. Extensive irradiation studies have conducted on F82H, and it has the most extensive available database of irradiated and unirradiated properties of all RAFMs. The objective of this paper is to review the R and D status of F82H and to identify the key technical issues for the fabrication of an ITER test blanket module (TBM) suggested from the recent research achievements in Japan. This work clarified that the primary issues with F82H involve welding techniques and the mechanical properties of weld joints. This is the result of the distinctive nature of the joint caused by the phase transformation that occurs in the weld joint during cooling, and its impact on the design of a TBM will be discussed

Enhanced hydrogen storage properties of MgH2 co-catalyzed with K2NiF6 and CNTs.

Science.gov (United States)

Sulaiman, N N; Ismail, M

2016-12-06

The composite of MgH 2 /K 2 NiF 6 /carbon nanotubes (CNTs) is prepared by ball milling, and its hydrogenation properties are studied for the first time. MgH 2 co-catalyzed with K 2 NiF 6 and CNTs exhibited an improvement in the onset dehydrogenation temperature and isothermal de/rehydrogenation kinetics compared with the MgH 2 -K 2 NiF 6 composite. The onset dehydrogenation temperature of MgH 2 doped with 10 wt% K 2 NiF 6 and 5 wt% CNTs is 245 °C, which demonstrated a reduction of 25 °C compared with the MgH 2 + 10 wt% K 2 NiF 6 composite. In terms of rehydrogenation kinetics, MgH 2 doped with 10 wt% K 2 NiF 6 and 5 wt% CNTs samples absorbed 3.4 wt% of hydrogen in 1 min at 320 °C, whereas the MgH 2 + 10 wt% K 2 NiF 6 sample absorbed 2.6 wt% of hydrogen under the same conditions. For dehydrogenation kinetics at 320 °C, the MgH 2 + 10 wt% K 2 NiF 6 + 5 wt% CNTs sample released 3.3 wt% hydrogen after 5 min of dehydrogenation. By contrast, MgH 2 doped with 10 wt% K 2 NiF 6 released 3.0 wt% hydrogen in the same time period. The apparent activation energy, E a , for the dehydrogenation of MgH 2 doped with 10 wt% K 2 NiF 6 reduced from 100.0 kJ mol -1 to 70.0 kJ mol -1 after MgH 2 was co-doped with 10 wt% K 2 NiF 6 and 5 wt% CNTs. Based on the experimental results, the hydrogen storage properties of the MgH 2 /K 2 NiF 6 /CNTs composite is enhanced because of the catalytic effects of the active species of KF, KH and Mg 2 Ni that are formed in situ during dehydrogenation, as well as the unique structure of CNTs.

Low temperature preparation and superconductivity of F-doped SmFeAsO

Energy Technology Data Exchange (ETDEWEB)

Chen, Y.L.; Cui, Y.J. [Key Laboratory of Magnetic Levitation Technologies and Maglev Trains (Ministry of Education of China), Superconductivity R and D Center (SRDC), Mail Stop 165, Southwest Jiaotong University, Chengdu, Sichuan 610031 (China); Cheng, C.H. [School of Materials Science and Engineering, University of New South Wales, Sydney, 2052 NSW (Australia); Yang, Y.; Wang, L.; Li, Y.C.; Zhang, Y. [Key Laboratory of Magnetic Levitation Technologies and Maglev Trains (Ministry of Education of China), Superconductivity R and D Center (SRDC), Mail Stop 165, Southwest Jiaotong University, Chengdu, Sichuan 610031 (China); Zhao, Y., E-mail: yzhao@swjtu.edu.c [Key Laboratory of Magnetic Levitation Technologies and Maglev Trains (Ministry of Education of China), Superconductivity R and D Center (SRDC), Mail Stop 165, Southwest Jiaotong University, Chengdu, Sichuan 610031 (China); School of Materials Science and Engineering, University of New South Wales, Sydney, 2052 NSW (Australia)

2010-11-01

A low temperature (1100 deg. C) process of preparing F-doped SmFeAsO samples has been developed using SmF{sub 3} with nanometer scale as the source of fluorine. A series of the SmFeAsO{sub 1-x}F{sub x} (x = 0, 0.05, 0.1, 0.15, 0.2, 0.25, 0.3) samples have been prepared using the present method. Compared with previous reports, the present SmF{sub 3} is more effective to introduce F into SmFeAsO system in which a transition temperature of 39 K can be observed when x = 0.05. The superconductivity is definitely enhanced with the increasing F-doping level. All the samples presented to be layered structure and the crystal particle size is about three times larger with sintering time increasing from 36 h to 48 h. Except for the nanometer scale of SmF{sub 3}, the flux effect of SmF{sub 3} is recognized to be another reason for the decrease of the sintering temperature. Further more, a relatively large amount of SmF{sub 3} was also employed in the raw materials to introduce excessive F and this has induced higher T{sub c} (55 K) in SmFeAsO{sub 0.8}F{sub 0.2+{delta}}system.

Scintillation and radiation damage of doped BaF2 crystals

International Nuclear Information System (INIS)

Gong Zufang; Xu Zizong; Chang Jin

1992-01-01

The emission spectra and the radiation damage of BaF 2 crystals doped Ce and Dy have been studied. The results indicate that the doped BaF 2 crystals have the intrinsic spectra of impurity besides the intrinsic spectra of BaF 2 crystals. The crystals colored and the transmissions decrease with the concentration of impurity in BaF 2 crystals after radiation by γ-ray of 60 Co. The doped Ce BaF 2 irradiated by ultraviolet has faster recover of transmissions but for doped Dy the effect is not obvious. The radiation resistance is not good as pure BaF 2 crystals

Finite element modeling and experimental study of brittle fracture in tempered martensitic steels for thermonuclear fusion applications

International Nuclear Information System (INIS)

Mueller, P. F.

2009-10-01

The present report studies the brittle fracture in high-chromium reduced activation tempered martensitic steels foreseen as structural materials for thermonuclear fusion reactors. Developing the adequate materials that can withstand the severe irradiation conditions of the burning plasma in a fusion reactor is one of the major challenges to be solved in order to make profit from the great advantages of thermonuclear fusion as an energy source. High-chromium tempered martensitic steels such as F82H and the most advanced version Eurofer97 are among the main candidate materials for structural applications in future fusion power plants due to low irradiation-induced swelling, good mechanical and thermal properties, and reasonably fast radioactive decay. Drawback of this kind of steels is irradiation embrittlement, which is manifested by a ductile-to-brittle transition temperature shift to higher temperatures after irradiation. The laboratory specimen fracture data has to be transferred to real components in order to assess the performance of these steels in the different operating and transient conditions they could find during the operation life of a fusion reactor. The specimen geometry effects and specimen size effects on measured fracture toughness need to be properly understood, taken into account and predicted with an appropriate model. The microstructure of Eurofer97 and F82H has been characterized and compared by means of optical microscopy, scanning electron microscopy, transmission electron microscopy and energy-dispersive X-ray spectroscopy in order to identify microstructural features that could play a role in the measured fracture toughness. Both steels have similar but slightly different chemical composition and final heat treatments but the prior austenitic grain size measured in F82H is approximately 8 times larger than in Eurofer97. The alloying element tantalum is added to stabilize the austenite grain size. In Eurofer97 it forms carbides of an

Microstructural characterization of dissimilar welds between Incoloy 800H and 321 Austenitic Stainless Steel

Energy Technology Data Exchange (ETDEWEB)

Sayiram, G., E-mail: sayiram.g@vit.ac.in; Arivazhagan, N.

2015-04-15

In this work, the microstructural character of dissimilar welds between Incoloy 800H and 321 Stainless Steel has been discussed. The microscopic examination of the base metals, fusion zones and interfaces was characterized using an optical microscope and scanning electron microscopy. The results revealed precipitates of Ti (C, N) in the austenitic matrix along the grain boundaries of the base metals. Migration of grain boundaries in the Inconel 82 weld metal was very extensive when compared to Inconel 617 weldment. Epitaxial growth was observed in the 617 weldment which increases the strength and ductility of the weld metal. Unmixed zone near the fusion line between 321 Stainless Steel and Inconel 82 weld metal was identified. From the results, it has been concluded that Inconel 617 filler metal is a preferable choice for the joint between Incoloy 800H and 321 Stainless Steel. - Highlights: • Failure mechanisms produced by dissimilar welding of Incoloy 800H to AISI 321SS • Influence of filler wire on microstructure properties • Contemplative comparisons of metallurgical aspects of these weldments • Microstructure and chemical studies including metallography, SEM–EDS • EDS-line scan study at interface.

Electrodeposition of zinc-doped silane films for corrosion protection of mild steels

International Nuclear Information System (INIS)

Wu Liankui; Hu Jiming; Zhang Jianqing

2012-01-01

Highlights: ► Metallic zinc is doped into organosilane films by one-step electrodeposition. ► The composite films exhibit the improved corrosion resistance of mild steels. ► Zinc-doping provides additional cathodic protection to the mild steels. - Abstract: Organosilane/zinc composite films are prepared by one-step electrodeposition onto cold-rolled steels for corrosion protection. Electrochemical impedance spectroscopy measurement, bulk solution immersion and wet heat tests all show that the composite films have improved corrosion performance. X-ray photoelectron spectroscopy measurement suggests the successful encapsulation of metallic zinc. The embedding of metallic zinc results in negative shift in open-circuit potential of the film-covered electrodes. Such cathodic protection effect given by the metallic zinc provides the improved corrosion resistance of the composite films.

Friction Stir Welding of HT9 Ferritic-Martensitic Steel: An Assessment of Microstructure and Properties

Science.gov (United States)

2013-06-01

report of FSW on a ferritic- martensitic stainless steel is the work of Chung, which applied this approach to a dissimilar weld between F82H (ferritic... martensitic ) and SUS304 (austenitic stainless ) [43]. 7 D. CORROSION OF FERRITIC/ MARTENSITIC STEELS IN HIGH TEMPERATURE MOLTEN SALT COOLANTS In...Philadelphia, PA, 1992, pp. 1267–1286, March 1990. [15] S. Rosenwasser, ―The application of martensitic stainless steels in a lifelong fusion first wall

XPS study of the ultrathin a-C:H films deposited onto ion beam nitrided AISI 316 steel

International Nuclear Information System (INIS)

Meskinis, S.; Andrulevicius, M.; Kopustinskas, V.; Tamulevicius, S.

2005-01-01

Effects of the steel surface treatment by nitrogen ion beam and subsequent deposition of the diamond-like carbon (hydrogenated amorphous carbon (a-C:H) and nitrogen doped hydrogenated amorphous carbon (a-CN x :H)) films were investigated by means of the X-ray photoelectron spectroscopy (XPS). Experimental results show that nitrogen ion beam treatment of the AISI 316 steel surface even at room temperature results in the formation of the Cr and Fe nitrides. Replacement of the respective metal oxides by the nitrides takes place. Formation of the C-N bonds was observed for both ultrathin a-C:H and ultrathin a-CN x :H layers deposited onto the nitrided steel. Some Fe and/or Cr nitrides still were presented at the interface after the film deposition, too. Increased adhesion between the steel substrate and hydrogenated amorphous carbon layer after the ion beam nitridation was explained by three main factors. The first two is steel surface deoxidisation/passivation by nitrogen as a result of the ion beam treatment. The third one is carbon nitride formation at the nitrided steel-hydrogenated amorphous carbon (or a-CN x :H) film interface

Effect of hydrogen doping on the properties of Al and F co-doped ZnO films for thin film silicon solar cell applications

Energy Technology Data Exchange (ETDEWEB)

Wang, Fang-Hsing, E-mail: fansen@dragon.nchu.edu.tw; Yang, Tung-Hsin

2016-04-30

Aluminum and fluorine co-doped zinc oxide (AFZO) thin films were prepared in Ar + H{sub 2} atmospheres by rf magnetron sputtering at room temperature. The structural, electrical, and optical properties of the prepared films were investigated using X-ray diffraction, scanning electron microscopy, atomic force microscopy, Hall-effect measurement, X-ray photoelectron spectroscopy, and ultraviolet–visible spectrometry, and their dependence on deposition atmosphere (i.e. H{sub 2} / (H{sub 2} + Ar) ratio) was studied. The resulting films showed a (0 0 2) diffraction peak, indicating a typical wurtzite structure, and the optimal film crystallinity was obtained with the H{sub 2} / (H{sub 2} + Ar) ratio of 3%. The electrical resistivity of AFZO films decreased to 9.16 × 10{sup −4} Ω-cm, which was lower than ZnO:Al and ZnO:F films due to double doping effect of Al and F. The resistivity further decreased to below 5 × 10{sup −4} Ω-cm for the AFZO film with the H{sub 2} / (H{sub 2} + Ar) ratio of 3%–5%. All the films regardless of hydrogen content displayed high transmittances (> 92%) in the visible wavelength range. Applying the developed AFZO films as front transparent electrodes, amorphous Si thin film solar cells were fabricated and the open-circuit voltage, fill factor, and efficiency of the cell with the hydrogenated AFZO film were improved in contrast to those without the hydrogenated film. - Highlights: • H{sub 2} doping improves optoelectronic properties of Al, F co-doped ZnO (AFZO) films. • Resistivity of AFZO films decreases to 4.4 × 10{sup −4} Ω-cm with the 3% H{sub 2}/(Ar + H{sub 2}) ratio. • AFZO films show high average visible transmittances of above 92%. • Efficiency of a-Si thin film solar cells is improved by AFZO:H as front electrode.

Effect of ZDDP concentration on the thermal film formation on steel, hydrogenated non-doped and Si-doped DLC

Energy Technology Data Exchange (ETDEWEB)

Akbari, S. [Laboratory for Tribology and Interface Nanotechnology, University of Ljubljana, Ljubljana (Slovenia); Kovač, J. [Jozef Stefan Institute, Jamova 19, 1000 Ljubljana (Slovenia); Kalin, M., E-mail: mitjan.kalin@tint.fs.uni-lj.si [Laboratory for Tribology and Interface Nanotechnology, University of Ljubljana, Ljubljana (Slovenia)

2016-10-15

Highlights: • The effect of the ZDDP concentrations onto the steel, H-DLC and Si-DLC surfaces is investigated. • ZDDP film structure on the DLC coatings is different from steel. • Different concentrations of ZDDP do not affect the final chemical structure of the ZDDP film on any of the studied surfaces. • The thickness of the thermal film is linear with the concentration for a given surface. • The reactivity of the ZDDP film is higher on the steel surface than on the DLC coatings. - Abstract: This work focuses on the ZDDP concentration (1, 5 and 20 wt%) to form a ZDDP film on surfaces during static thermal tests at 150 °C. Silicon-doped and hydrogenated DLC coatings, as well as steel as reference, were studied using Attenuated Total Reflection-Fourier Transform Infrared (ATR-FTIR) spectroscopy and X-ray Photoelectron Spectroscopy (XPS). The results show that, on the three surfaces, the structure of the ZDDP thermal film consists of identical groups of pyrophosphate and zinc oxide, while the sulphuric groups are dissimilar. On the steel surface, the sulphuric part consists of a mixture of organic sulphide and sulphohydryl groups, but on H-DLC and Si-DLC only organic sulphide groups are found; there are no sulphohydryl groups. Moreover, both ATR-FTIR and XPS show that different concentrations of ZDDP do not affect the final chemical structure of the ZDDP thermal film on any of the studied surfaces. In addition, the XPS results show that the thickness of the thermal film is linear with the concentration for the whole range from 1 to 20 wt%, supporting also its uniform chemical structure. These thicknesses further show that the reactivity of the ZDDP film is higher on the steel surface than on the DLC coatings.

Tribochemical interactions of Si-doped DLC film against steel in sliding contact

International Nuclear Information System (INIS)

Yoon, Eui Sung; Pham, Duc Cuong; Ahn, Hyo Sok; Oh, Jae Eung

2007-01-01

This study concerns the effects of tribochemical interactions at the interface of Si-DLC (silicon-doped diamond-like carbon) film and steel ball in sliding contact on tribological properties of the film. The Si-DLC film was over-coated on pure DLC coating by radio frequency plasma-assisted chemical vapor deposition (r.f. PACVD) with different Si concentration. Friction tests against steel ball using a reciprocating type tribotester were performed in ambient environment. X-Ray photoelectron spectroscopy (XPS) and auger electron spectroscopy (AES) were used to study the chemical characteristics and elemental composition of the films and mating balls after tests. Results showed a darkgray film consisting of carbon, oxygen and silicon on the worn steel ball surface with different thickness. On the contrary, such film was not observed on the surface of the ball slid against pure DLC coating. The oxidation of Si-DLC surface and steel ball was also found at particular regions of contact area. This demonstrates that tribochemical interactions occurred at the contact area of Si-DLC and steel ball during sliding to form a tribofilm (so called transfer film) on the ball specimen. While the pure DLC coating exhibited high coefficient of friction (∼0.06), the Si-DLC film showed a significant lower coefficient of friction (∼0.022) with the presence of tribofilm on mating ball surface. However, the Si-DLC film possesses a very high wear rate in comparison with the pure DLC. It was found that the tribochemical interactions strongly affected tribological properties of the Si-DLC film in sliding against steel

Hydrogen storage properties of the Zintl phase alloy SrAl{sub 2} doped with TiF{sub 3}

Energy Technology Data Exchange (ETDEWEB)

Zhu Yunfeng, E-mail: yfzhu@njut.edu.c [College of Materials Science and Engineering, Nanjing University of Technology, 5 Xinmofan Road, Nanjing 210009 (China); Zhang Wei; Liu Zhibing; Li Liquan [College of Materials Science and Engineering, Nanjing University of Technology, 5 Xinmofan Road, Nanjing 210009 (China)

2010-03-04

In this paper, the structural and hydrogenation characteristics of TiF{sub 3}-doped Zintl phase alloy SrAl{sub 2} were studied by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and hydrogenation measurements. The results show that the hydrogenation kinetics of the Zintl phase alloy SrAl{sub 2} is improved greatly after doping with TiF{sub 3}. By adjusting the doping amount and ball milling time, the optimal doping conditions were obtained. The catalytic mechanism of TiF{sub 3} for the hydrogenation of SrAl{sub 2} was also investigated. SrAl{sub 2} does not react with TiF{sub 3} during the ball milling process. However, it reacts with TiF{sub 3} to form SrAl{sub 2}H{sub 2}, SrF{sub 2}, SrAl{sub 4} and Ti during the hydrogenation process, among which Ti plays an important role in the hydrogenation kinetics of SrAl{sub 2}.

Ho3+-doped AlF3-TeO2-based glass fibers for 2.1 µm laser applications

Science.gov (United States)

Wang, S. B.; Jia, Z. X.; Yao, C. F.; Ohishi, Y.; Qin, G. S.; Qin, W. P.

2017-05-01

Ho3+-doped AlF3-TeO2-based glass fibers based on AlF3-BaF2-CaF2-YF3-SrF2-MgF2-TeO2 glasses are fabricated by using a rod-in-tube method. The glass rod including a core and a thick cladding layer is prepared by using a suction method, where the thick cladding layer is used to protect the core from the effect of surface crystallization during the fiber drawing. By inserting the glass rod into a glass tube, the glass fibers with relatively low loss (~2.3 dB m-1 @ 1560 nm) are prepared. By using a 38 cm long Ho3+-doped AlF3-TeO2-based glass fiber as the gain medium and a 1965 nm fiber laser as the pump source, 2065 nm lasing is obtained for a threshold pump power of ~220 mW. With further increasing the pump power to ~325 mW, the unsaturated output power of the 2065 nm laser is about 82 mW and the corresponding slope efficiency is up to 68.8%. The effects of the gain fiber length on the lasing threshold, the slope efficiency, and the operating wavelength are also investigated. Our experimental results show that Ho3+-doped AlF3-TeO2-based glass fibers are promising gain media for 2.1 µm laser applications.

Characteristics of F doped PZT ceramics using different fluorine sources

Energy Technology Data Exchange (ETDEWEB)

Guiffard, B. [Laboratory of Electrical Engineering and Ferroelectricity, LGEF INSA-Lyon, Bat. Gustave Ferrie, 8 rue de la Physique, F-69621 Villeurbanne Cedex (France)]. E-mail: benoit.guiffard@insa-lyon.fr; Boucher, E. [SPCTS, UMR 6638, Faculte des Sciences et Techniques, Universite de Limoges, 123 Avenue Albert Thomas, 87060 Limoges Cedex (France); Lebrun, L. [Laboratory of Electrical Engineering and Ferroelectricity, LGEF INSA-Lyon, Bat. Gustave Ferrie, 8 rue de la Physique, F-69621 Villeurbanne Cedex (France); Guyomar, D. [Laboratory of Electrical Engineering and Ferroelectricity, LGEF INSA-Lyon, Bat. Gustave Ferrie, 8 rue de la Physique, F-69621 Villeurbanne Cedex (France)

2007-02-25

In this study, some structural and electrical properties of a PZT base composition Pb{sub 0.89}(Ba, Sr){sub 0.11}(Zr{sub 0.52}Ti{sub 0.48})O{sub 3} co-doped with 1 mol% manganese and 2 mol% fluorine have been studied. Two different fluorine sources were used: lead fluoride PbF{sub 2} and manganese fluoride MnF{sub 2}. These fluoride salts are added to the co-precipitated precursors powder. Mn dopant was added to the solution as manganese acetate (MnAc) before co-precipitation, when PbF{sub 2} was used. The structural analysis of the sintered ceramics revealed that MnF{sub 2} doping makes the volume of the cubic unit cell (V {sub c}) and the grain size decrease, whereas (MnAc, PbF{sub 2}) co-doping makes the apparent density increase and keeps the average grain size and V {sub c} unchanged. Both types of doping reagents largely enhance the piezoelectric activity (high d {sub 33} and k {sub 33} coefficients, well saturated Polarization-Electric field loops) but MnF{sub 2} induces both combinatory soft and hard characteristics compared to (MnAc, PbF{sub 2}) co-doping. Impedance spectroscopy showed that both types of doping reagents strongly reduce the electrical conductivity with the same conducting species, i.e. the same defect chemistry, confirmed by optical absorption data. Finally, this study shows that in the semi-wet process used, PbF{sub 2} is added homogeneously to the co-precipitated powder. Whatever the fluorine source, only the coexistence of Mn and F dopants is necessary to improve the piezoelectric response.

Enhanced electrochemical properties of F-doped Li2MnSiO4/C for lithium ion batteries

Science.gov (United States)

Wang, Chao; Xu, Youlong; Sun, Xiaofei; Zhang, Baofeng; Chen, Yanjun; He, Shengnan

2018-02-01

The Li2MnSiO4 as a novel cathode material for lithium ion batteries, performs high specific capacity, high thermal stability, low cost and etc. However, it suffers from relatively low electronic conductivity and lithium ion diffusion rate. Herein, we successfully introduce fluorine to Li2MnSiO4 (Li2MnSiO4-xFx, x = 0.00, 0.01, 0.03 and 0.05) to overcome these obstacles. The results show that F doping not only enlarges the lattice parameters but also decreases the particle size, synergistically improving the lithium ion diffusion of Li2MnSiO4. Moreover, F doping increase electronic conductivity of Li2MnSiO4/C by inhibiting the formation of C-O bonds in the carbon layers. Meanwhile, F doping improves the crystallinity and stabilizes the crystal structure of Li2MnSiO4. Finally, the Li2MnSiO3.97F0.03/C with the best electrochemical performances delivers the initial specific discharge capacity of 279 mA h g-1 at 25mA g-1 current density from 1.5 V to 4.8 V. Also, it maintains a higher capacity (201 mA h g-1) than F-free Li2MnSiO4 (145 mA h g-1) after 50 cycles.

Creep strength of reduced activation ferritic/martensitic steel Eurofer'97

International Nuclear Information System (INIS)

Fernandez, P.; Lancha, A.M.; Lapena, J.; Lindau, R.; Rieth, M.; Schirra, M.

2005-01-01

Creep rupture strength of tempered martensitic steel Eurofer'97 has been investigated. Different products form (plate and bar) have been tested in the temperature range from 450 deg. C to 650 deg. C at different loads. No significant differences in the creep rupture properties have been found between the studied product forms. The Eurofer'97 has shown adequate creep rupture strength levels at short creep rupture tests, similar to those of the F-82 H mod. steel. However, for long testing times (>9000 h) the results available up to now at 500 deg. C and 550 deg. C seem to indicate a change in the creep degradation mechanism

Metallurgical characterization of the reduced activation ferritic/martensitic steel Eurofer'97 on as-received condition

International Nuclear Information System (INIS)

Fernandez, P.; Lancha, A.M.; Lapena, J.; Hernandez-Mayoral, M.

2001-01-01

A new European reduced activation ferrous alloy (denominated Eurofer'97) developed as possible first wall and breeder blanket structural material for fusion applications is being characterized. In this paper, activities specially focussed to investigate the microstructural and mechanical properties of this material on the as-received state (normalized at 980 degree sign C/27' plus tempered at 760 degree sign C/90'/air cooled) are presented. Chemical analyses, a detailed microstructural study, hardness, tensile and Charpy tests have been carried out and are compared to the reduced activation material F-82H modified previously studied. The results show that the Eurofer'97 is a fully martensitic steel free of δ-ferrite with similar tensile and better impact properties than the F-82H modified steel. Two types of carbides have been observed in the Eurofer'97, namely, Cr rich precipitates and Ta/V rich precipitates, tentatively identified as M 23 C 6 type and (Ta,V)C type, respectively

Dosimeter properties of Ce and Eu doped LiCaAlF6

International Nuclear Information System (INIS)

Yanagida, Takayuki; Fujimoto, Yutaka; Watanabe, Kenichi; Fukuda, Kentaro

2014-01-01

Optical, scintillation properties, optical stimulated luminescence, and thermally stimulated luminescence of Ce 1, 3, and 5% doped and Eu 1, 1.5, and 2% doped LiCaAlF 6 crystals fabricated by Tokuyama Corp. were investigated. In transmittance, absorption was proportional to dopant concentrations and typical optical quantum yield of Ce and Eu-doped LiCaAlF 6 were 40 and 100%, respectively. Scintillation wavelength and decay time profiles were investigated under X-ray irradiation. Ce 3+ and Eu 2+ 5d-4f luminescence appeared around 300 nm and 370 nm with typical decay time of 40 ns and 1.5 μs, respectively. Optically stimulated luminescence of Ce-doped ones appeared under 405 nm stimulation with detectable intensity while those of Eu doped ones were quite weak. Thermally stimulated luminescence of Ce- and Eu-doped LiCaAlF 6 were enough strong and they exhibited good response function from 1 to 1000 mGy exposure. - Highlights: • Optical, scintillation, OSL, and TSL properties of Ce or Eu differently doped LiCaAlF6 were studied. • PL quantum yield of Ce and Eu doped LiCaAlF6 showed 40% and 100%, respectively. • OSL was observed in Ce-doped LiCaAlF6. • TSL was observed in both material systems and exhibited a good dose response from 1 to 1000 mGy

Electronic structures and magnetism of CaFeAsH and CaFeAsF

International Nuclear Information System (INIS)

Wang Guangtao; Shi Xianbiao; Liu Haipeng; Liu Qingbo

2015-01-01

We studied the electronic structures, magnetism, and Fermi surface (FS) nesting of CaFeAsH and CaFeAsF by first-principles calculations. In the nonmagnetic (NM) states, we found strong FS nesting, which induces magnetic instability and a spin density wave (SDW). Our calculations indicate that the ground state of CaFeAsH and CaFeAsF is the stripe antiferromagnetic state. The calculated bare susceptibility χ 0 (q) peaked at the M-point and was clearly suppressed and became slightly incommensurate with both electron doping and hole doping for both materials. (author)

Mechanical properties and electronic structure of edge-doped graphene nanoribbons with F, O, and Cl atoms.

Science.gov (United States)

Piriz, Sebastián; Fernández-Werner, Luciana; Pardo, Helena; Jasen, Paula; Faccio, Ricardo; Mombrú, Álvaro W

2017-08-16

In this study, we present the structural, electronic, and mechanical properties of edge-doped zigzag graphene nanoribbons (ZGNRs) doped with fluorine, oxygen, and chlorine atoms. To the best of our knowledge, to date, no experimental results concerning the mechanical properties of graphene-derived nanoribbons have been reported in the literature. Simulations indicate that Cl- and F-doped ZGNRs present an equivalent 2-dimensional Young's modulus E 2D , which seems to be higher than those of graphene and H-doped ZGNRs. This is a consequence of the electronic structure of the system, particularly originating from strong interactions between the dopant atoms localized at the edges. The interaction between dopant atoms located at the edges is higher for Cl and lower for F and O atoms. This is the origin of the observed trend, in which E > E > E for all the analyzed ZGNRs.

Effect of ZDDP concentration on the thermal film formation on steel, hydrogenated non-doped and Si-doped DLC

Science.gov (United States)

Akbari, S.; Kovač, J.; Kalin, M.

2016-10-01

This work focuses on the ZDDP concentration (1, 5 and 20 wt%) to form a ZDDP film on surfaces during static thermal tests at 150 °C. Silicon-doped and hydrogenated DLC coatings, as well as steel as reference, were studied using Attenuated Total Reflection-Fourier Transform Infrared (ATR-FTIR) spectroscopy and X-ray Photoelectron Spectroscopy (XPS). The results show that, on the three surfaces, the structure of the ZDDP thermal film consists of identical groups of pyrophosphate and zinc oxide, while the sulphuric groups are dissimilar. On the steel surface, the sulphuric part consists of a mixture of organic sulphide and sulphohydryl groups, but on H-DLC and Si-DLC only organic sulphide groups are found; there are no sulphohydryl groups. Moreover, both ATR-FTIR and XPS show that different concentrations of ZDDP do not affect the final chemical structure of the ZDDP thermal film on any of the studied surfaces. In addition, the XPS results show that the thickness of the thermal film is linear with the concentration for the whole range from 1 to 20 wt%, supporting also its uniform chemical structure. These thicknesses further show that the reactivity of the ZDDP film is higher on the steel surface than on the DLC coatings.

Silver doped metal layers for medical applications

International Nuclear Information System (INIS)

Kocourek, T; Jelínek, M; Mikšovský, J; Jurek, K; Weiserová, M

2014-01-01

Biological, physical and mechanical properties of silver-doped layers of titanium alloy Ti6Al4V and 316L steel prepared by pulsed laser deposition were studied. Metallic silver-doped coatings could be a new route for antibacterial protection in medicine. Thin films of silver and silver-doped materials were synthesized using KrF excimer laser deposition. The materials were ablated from two targets, which were composed either from titanium alloy with silver segments or from steel with silver segments. The concentration of silver ranged from 1.54 at% to 4.32 at% for steel and from 3.04 at% to 13.05 at% for titanium alloy. The layer properties such as silver content, structure, adhesion, surface wettability, and antibacterial efficacy (evaluated by Escherichia coli and Bacillus subtilis bacteria) were measured. Film adhesion was studied using scratch test. The antibacterial efficacy changed with silver doping up to 99.9 %. Our investigation was focused on minimum Ag concentration needed to reach high antibacterial efficiency, high film adhesion, and hardness.

Silver-doped metal layers for medical applications

International Nuclear Information System (INIS)

Kocourek, T; Jelínek, M; Mikšovský, J; Jurek, K; Weiserová, M

2014-01-01

Biological, physical and mechanical properties of silver-doped layers of titanium alloy Ti6Al4V and 316 L steel prepared by pulsed laser deposition were studied. Metallic silver-doped coatings could be a new route for antibacterial protection in medicine. Thin films of silver and silver-doped materials were synthesized using KrF excimer laser deposition. The materials were ablated from two targets, which were composed either from titanium alloy with silver segments or from steel with silver segments. The concentration of silver ranged from 1.54 to 4.32 at% for steel and from 3.04 to 13.05 at% for titanium alloy. The layer properties such as silver content, structure, adhesion, surface wettability, and antibacterial efficiency (evaluated by Escherichia coli and Bacillus subtilis bacteria) were measured. Film adhesion was studied using a scratch test. The antibacterial efficiency changed with silver doping up to 99.9 %. Our investigation was focused on the minimum Ag concentration needed to reach high antibacterial efficiency, high film adhesion, and hardness. (paper)

Structural and mechanical properties of welded joints of reduced activation martensitic steels

International Nuclear Information System (INIS)

Filacchioni, G.; Montanari, R.; Tata, M.E.; Pilloni, L.

2002-01-01

Gas tungsten arc welding and electron beam welding methods were used to realise welding pools on plates of reduced activation martensitic steels. Structural and mechanical features of these simulated joints have been investigated in as-welded and post-welding heat-treated conditions. The research allowed to assess how each welding technique affects the original mechanical properties of materials and to find suitable post-welding heat treatments. This paper reports results from experimental activities on BATMAN II and F82H mod. steels carried out in the frame of the European Blanket Project - Structural Materials Program

Improved dehydrogenation of TiF{sub 3}-doped NaAIH{sub 4} using mesoporous SiO{sub 2} as a co-dopant

Energy Technology Data Exchange (ETDEWEB)

Li, Y.; Zheng, S.; Fang, F.; Song, Y.; Sun, D. [Fudan Univ., Shanghai (China). Dept. of Materials Science

2010-07-01

This paper examined the improved dehydrogenation of titanium fluoride (TiF{sub 3})-doped sodium aluminum hydride (NaAIH{sub 4}) using mesoporous silicon dioxide (SiO{sub 2}) as a Co-dopant. The study revealed that the amount of hydrogen evolved was 3.8 wt. per cent for the pristine NaAlH{sub 4} and approximately 4.2 wt. per cent for the TiF{sub 3}-doped NaAlH{sub 4}. It increased to 4.9-5.0 wt. per cent once the samples were doped with mesoporous SiO{sub 2}. A favorable synergistic effect on the NaAlH{sub 4} dehydrogenation was achieved as mesoporous SiO{sub 2} was added as a co-dopant along with TiF{sub 3} which was associated with the nanosized pores and high specific surface area of mesoporous SiO{sub 2}. The catalytic mechanism of mesoporous SiO{sub 2} was more physical than chemical relative to the catalytic mechanism of TiF{sub 3}. 1 fig.

Neodymium-doped Sr5(PO4)3F and Sr5(VO4)3F

International Nuclear Information System (INIS)

Corker, D.L.; Nicholls, J.; Loutts, G.B.

1995-01-01

Neodymium-doped Sr 5 (PO 4 ) 3 F [neodymium strontium fluoride phosphate, (Nd,Sr) 5 (PO 4 ) 3 F] and neodymium-doped Sr 5 (VO 4 ) 3 F [neodymium strontium fluoride vanadate, (Nd,Sr) 5 (VO 4 ) 3 F] crystallize in space group P6 3 /m and are isostructural with calcium fluorophosphate, Ca 5 (PO 4 ) 3 F. There are two different Sr sites in Sr 5 (XO 4 ) 3 F, denoted Sr(1) and Sr(2). Using single-crystal X-ray diffraction the two structures were refined to R factors of 2.3 and 2.2%, respectively, showing that Nd is present at both Sr sites in (Sr,Nd) 5 (VO 4 ) 3 F but only at the Sr(2) site in (Sr,Nd) 5 (PO 4 ) 3 F. (orig.)

Synthesis and characterization of europium doped LiF phosphor

Energy Technology Data Exchange (ETDEWEB)

Villalobos, M. L.; Vallejo, M. A.; Sosa A, M. [Universidad de Guanajuato, Division de Ciencias e Ingenierias, Loma del Bosque No. 103, Lomas del Campestre, 37150 Leon, Guanajuato (Mexico); Diaz T, L. A., E-mail: villaloboscm2010@licifug.ugto.mx [Centro de Investigaciones en Optica, A. C., Loma del Bosque No. 115, Lomas del Campestre, 37150 Leon, Guanajuato (Mexico)

2015-10-15

LiF with different dopants has been one of the most investigated materials to use as thermoluminescent dosimeter. In this paper, we present the preparation method, the characterization and the thermoluminescent response of Eu doped LiF irradiated with X-rays. Pure and Eu doped LiF samples with different dopant concentration (0, 0.25, 0.5, 0.75 and 1 % mol) were synthesized using the precipitation method. The samples were structurally characterized by X-ray diffraction (XRD), the diffraction patterns showed a main cubic crystalline structure and a secondary hexagonal structure. The photoluminescence spectrum exhibited four well defined peaks characteristic of the Eu{sup 3+} ion. Thermoluminescent (Tl) glow curves of x-ray irradiated samples showed a well-defined single peak around 200 degrees C, except for the pure and 0.25% Eu doped samples. (Author)

Friction stir welding of F/M ODS steel plug and F/M steel tube

Energy Technology Data Exchange (ETDEWEB)

Kang, Suk Hoon, E-mail: shkang77@kaeri.re.kr [Nuclear Materials Division, Korea Atomic Energy Research Institute (Korea, Republic of); Vasudevan, M. [Materials Technology Division, Indira Gandhi Centre for Atomic Research, Kalpakkam (India); Noh, Sanghoon; Jin, Hyun Ju; Jang, Jinsung; Kim, Tae Kyu [Nuclear Materials Division, Korea Atomic Energy Research Institute (Korea, Republic of)

2016-11-01

Highlights: • Friction stir welding (FSW) was used for joining of oxide dispersion strengthened (ODS) steel plug and F/M steel tube. • The curvature and smaller thickness of tube was the major limitation for applying FSW method, it was solved using specially designed jig. • Considerable hardening occurs in the joint because the cooling rate was sufficient to reproduce a martensitic microstructure. • The measured hoop strength of the FSWed joint was 70–90 MPa, the value was at around 70% of the tube. - Abstract: Friction stir welding (FSW) was used for joining of oxide dispersion strengthened (ODS) steel plug and F/M steel tube. The dimensions of the tube included outer diameter of 7 mm, wall thickness of 0.5 mm. The objective was to find suitable process variables for gaining enough frictional heat from those thin and curved pieces. A specially designed jig was used for stabilization and slow rotation of tube during FSW. Additionally, the plug was designed to overlap the tube. Inconel 718 was used as FSW tool, the diameter was 3.5 mm. The adequate rotation speed of the tool and jig were 1200 rpm and 1.5 rpm, respectively. The joining was successfully accomplished using above combination, showing a good possibility. The hoop stress tests of joint were conducted by blowing Ar gas into the tube, the flow rate of gas was 10 MPa/min. The measured hoop stress was 70–90 MPa, the value was at around 70% of the tube.

Friction stir welding of F/M ODS steel plug and F/M steel tube

International Nuclear Information System (INIS)

Kang, Suk Hoon; Vasudevan, M.; Noh, Sanghoon; Jin, Hyun Ju; Jang, Jinsung; Kim, Tae Kyu

2016-01-01

Highlights: • Friction stir welding (FSW) was used for joining of oxide dispersion strengthened (ODS) steel plug and F/M steel tube. • The curvature and smaller thickness of tube was the major limitation for applying FSW method, it was solved using specially designed jig. • Considerable hardening occurs in the joint because the cooling rate was sufficient to reproduce a martensitic microstructure. • The measured hoop strength of the FSWed joint was 70–90 MPa, the value was at around 70% of the tube. - Abstract: Friction stir welding (FSW) was used for joining of oxide dispersion strengthened (ODS) steel plug and F/M steel tube. The dimensions of the tube included outer diameter of 7 mm, wall thickness of 0.5 mm. The objective was to find suitable process variables for gaining enough frictional heat from those thin and curved pieces. A specially designed jig was used for stabilization and slow rotation of tube during FSW. Additionally, the plug was designed to overlap the tube. Inconel 718 was used as FSW tool, the diameter was 3.5 mm. The adequate rotation speed of the tool and jig were 1200 rpm and 1.5 rpm, respectively. The joining was successfully accomplished using above combination, showing a good possibility. The hoop stress tests of joint were conducted by blowing Ar gas into the tube, the flow rate of gas was 10 MPa/min. The measured hoop stress was 70–90 MPa, the value was at around 70% of the tube.

High electrical resistivity Nd-Fe-B die-upset magnet doped with eutectic DyF3–LiF salt mixture

Directory of Open Access Journals (Sweden)

K. M. Kim

2017-05-01

Full Text Available Nd-Fe-B-type die-upset magnet with high electrical resistivity was prepared by doping of eutectic DyF3–LiF salt mixture. Mixture of melt-spun Nd-Fe-B flakes (MQU-F: Nd13.6Fe73.6Co6.6Ga0.6B5.6 and eutectic binary (DyF3–LiF salt (25 mol% DyF3 – 75 mol% LiF was hot-pressed and then die-upset. By adding the eutectic salt mixture (> 4 wt%, electrical resistivity of the die-upset magnet was enhanced to over 400 μΩ.cm compared to 190 μΩ.cm of the un-doped magnet. Remarkable enhancement of the electrical resistivity was attributed to homogeneous and continuous coverage of the interface between flakes by the easily melted eutectic salt dielectric mixture. It was revealed that active substitution of the Nd atoms in neighboring flakes by the Dy atoms from the added (DyF3–LiF salt mixture had occurred during such a quick thermal processing of hot-pressing and die-upsetting. This Dy substitution led to coercivity enhancement in the die-upset magnet doped with the eutectic (DyF3–LiF salt mixture. Coercivity and remanence of the die-upset magnet doped with (DyF3–LiF salt mixture was as good as those of the DyF3-doped magnet.

Pilot-scale ultrafiltration testing for the F and H area effluent treatment facility

International Nuclear Information System (INIS)

Kessler, J.L.

1984-01-01

An F and H Area Effluent Treatment Facility (F/H ETF) is being designed to treat low activity aqueous effluents which are produced from F and H Area daily operations. The treatment scheme for the F/H ETF will include pretreatment (pH adjustment and filtration) followed by Reverse Osmosis and/or Ion Exchange to remove dissolved species. Several alternative treatment processes are being considered for the F/H ETF. One of the alternatives in the pretreatment step is tubular Ultrafiltration (UF), using a dynamically formed zirconium oxide membrane supported on a porous stainless steel backing. Pilot-scale testing with a single membrane module (13 ft 2 area) and 200-Area effluent simulant has demonstrated that UF is a viable filtration option for the F/H ETF. UF testing at TNX has defined the operating conditions necessary for extended operation and also demonstrated excellent filtration performance (filtrate SDI 2 /day) flux and will provide excellent pretreatment for both reverse osmosis and ion exchange. 2 refs

Interfacial properties of HIP joint between beryllium and reduced activation ferritic/martensitic steel

International Nuclear Information System (INIS)

Hirose, T.; Ogiwara, H.; Enoeda, M.; Akiba, M.

2007-01-01

Full text of publication follows: ITER test blanket module is the most important components to validate energy production and fuel breeding process for future demonstration reactor. Reduced activation ferritic / martensitic steel is recognized as a promising structural material for breeding blanket systems. And Beryllium must be used as plasma facing materials for ITER in vessel components. In this work, interfacial properties of beryllium/reduced activation ferritic/martensitic steel (RAF/Ms) joint were investigated for a first wall of ITER test blanket module (TBM). The starting materials were ITER grade Beryllium, S65C and a Japanese RAF/M, F82H. The joint was produced by solid state hot isostatic pressing (HIP) method. Chromium layer with the thickness of 1 μm and 10 μm were formed by plasma vapor deposition on the beryllium surface as a diffusion barrier. The HIP was carried out at 1023 K and 1233 K which are determined by standard normalizing and tempering temperature of F82H. The joint made at 1233 K was followed by tempering at 1033 K. The bonding interface was characterized by electron probe microanalysis (EPMA). The bonding strength was also investigated by isometric four point bending tests at ambient temperature. EPMA showed chromium layer effectively worked as a diffusion barrier at 1023 K. However, the beryllium rich layer was formed in F82H after HIP at 1233 K followed by tempering. Bending tests revealed that thin chromium layer and low temperature HIP is preferable. The high temperature HIP introduce brittle BeFe inter metallic compounds along bonding interface. On the other hand, joint with thick chromium layer suffer from brittleness of chromium itself. (authors)

Interfacial properties of HIP joint between beryllium and reduced activation ferritic/martensitic steel

Energy Technology Data Exchange (ETDEWEB)

Hirose, T. [Blanket Engineering Group, Japan Atomic Energy Agency, Naka, Ibaraki (Japan); Ogiwara, H. [Japan Atomic Energy Agency, Tokai-mura, Naga-gun, Ibaraki-ken (Japan); Enoeda, M. [Naka Fusion Research Establishment, J.A.E.R.I., Japan Atomic Energy Research Institute, Naka-gun, Ibaraki-ken (Japan); Akiba, M. [Naka Fusion Institute, Japan Atomic Energy Agency, Naka, Ibaraki (Japan)

2007-07-01

Full text of publication follows: ITER test blanket module is the most important components to validate energy production and fuel breeding process for future demonstration reactor. Reduced activation ferritic / martensitic steel is recognized as a promising structural material for breeding blanket systems. And Beryllium must be used as plasma facing materials for ITER in vessel components. In this work, interfacial properties of beryllium/reduced activation ferritic/martensitic steel (RAF/Ms) joint were investigated for a first wall of ITER test blanket module (TBM). The starting materials were ITER grade Beryllium, S65C and a Japanese RAF/M, F82H. The joint was produced by solid state hot isostatic pressing (HIP) method. Chromium layer with the thickness of 1 {mu}m and 10 {mu}m were formed by plasma vapor deposition on the beryllium surface as a diffusion barrier. The HIP was carried out at 1023 K and 1233 K which are determined by standard normalizing and tempering temperature of F82H. The joint made at 1233 K was followed by tempering at 1033 K. The bonding interface was characterized by electron probe microanalysis (EPMA). The bonding strength was also investigated by isometric four point bending tests at ambient temperature. EPMA showed chromium layer effectively worked as a diffusion barrier at 1023 K. However, the beryllium rich layer was formed in F82H after HIP at 1233 K followed by tempering. Bending tests revealed that thin chromium layer and low temperature HIP is preferable. The high temperature HIP introduce brittle BeFe inter metallic compounds along bonding interface. On the other hand, joint with thick chromium layer suffer from brittleness of chromium itself. (authors)

Thermoluminescence of gamma rays irradiated LiF nanocubes doped with different elements

Energy Technology Data Exchange (ETDEWEB)

Salah, Numan, E-mail: nsalah@kau.edu.sa [Center of Nanotechnology, King Abdulaziz University, Jeddah 21589 (Saudi Arabia); Alharbi, Najlaa D. [Center of Nanotechnology, King Abdulaziz University, Jeddah 21589 (Saudi Arabia); Sciences Faculty for Girls, King Abdulaziz University, Jeddah 21589 (Saudi Arabia); Habib, Sami S. [Department of Aeronautical Engineering, King Abdulaziz University, Jeddah 21589 (Saudi Arabia)

2015-05-15

Lithium fluoride (LiF) doped with proper activator is a highly sensitive phosphor, widely used as a dosimeter for ionizing radiations. This work reports on the thermoluminesence (TL) response of LiF nanocubes doped with different impurities. These nanocubes were synthesized by the co-precipitation method and characterized by different techniques. The dopants used in this study are Eu, Tb, Dy, Cu and Ag. The gamma radiation induced TL glow peaks are located in the temperature range 120–125 °C. These samples have different TL sensitivities, where Eu doped one is found to be the most TL sensitive. Further irradiations in the dose range from 10 Gy to 30 kGy were performed to LiF:Eu and the obtained result is explained using a proposed multilevel TL model. According to this model, Eu dopant (in Eu{sup 3+} ionic form) could induce shallow and deep electron traps in the host of LiF nanocubes. These traps differ in their response according to the doses. The optimum concentration of Eu ions in LiF host is found to be 0.2 mol%. It is also found that LiF nanocubes are thermally stable in the range of 30–400 °C with a single phase. This property along with the good sensitivity of Eu doped one makes this tissue equivalent nanomaterial a proper candidate for heavy dose measurement like swift heavy ions used in radiotherapy. - Highlights: • Nanocubes of pure and doped LiF were produced by the co-precipitation method. • They were doped with Eu, Tb, Dy, Cu and Ag and studied for their TL response. • The gamma radiation induced TL glow peaks are located in the range 120–125 °C. • The Eu doped one is found to be the most TL sensitive, followed by Tb. • The tissue equivalent LiF:Eu nanocubes might be useful for heavy dose measurement.

Thermoluminescence of gamma rays irradiated LiF nanocubes doped with different elements

International Nuclear Information System (INIS)

Salah, Numan; Alharbi, Najlaa D.; Habib, Sami S.

2015-01-01

Lithium fluoride (LiF) doped with proper activator is a highly sensitive phosphor, widely used as a dosimeter for ionizing radiations. This work reports on the thermoluminesence (TL) response of LiF nanocubes doped with different impurities. These nanocubes were synthesized by the co-precipitation method and characterized by different techniques. The dopants used in this study are Eu, Tb, Dy, Cu and Ag. The gamma radiation induced TL glow peaks are located in the temperature range 120–125 °C. These samples have different TL sensitivities, where Eu doped one is found to be the most TL sensitive. Further irradiations in the dose range from 10 Gy to 30 kGy were performed to LiF:Eu and the obtained result is explained using a proposed multilevel TL model. According to this model, Eu dopant (in Eu 3+ ionic form) could induce shallow and deep electron traps in the host of LiF nanocubes. These traps differ in their response according to the doses. The optimum concentration of Eu ions in LiF host is found to be 0.2 mol%. It is also found that LiF nanocubes are thermally stable in the range of 30–400 °C with a single phase. This property along with the good sensitivity of Eu doped one makes this tissue equivalent nanomaterial a proper candidate for heavy dose measurement like swift heavy ions used in radiotherapy. - Highlights: • Nanocubes of pure and doped LiF were produced by the co-precipitation method. • They were doped with Eu, Tb, Dy, Cu and Ag and studied for their TL response. • The gamma radiation induced TL glow peaks are located in the range 120–125 °C. • The Eu doped one is found to be the most TL sensitive, followed by Tb. • The tissue equivalent LiF:Eu nanocubes might be useful for heavy dose measurement

Scintillation and optical stimulated luminescence of Ce-doped CaF2

International Nuclear Information System (INIS)

Yanagida, Takayuki; Fujimoto, Yutaka; Watanabe, Kenichi; Fukuda, Kentaro; Kawaguchi, Noriaki; Miyamoto, Yuka; Nanto, Hidehito

2014-01-01

Scintillation and optical stimulated luminescence of Ce 0.1–20% doped CaF 2 crystals prepared by Tokuyama Corp. were investigated. In X-ray induced scintillation spectra, luminescence due to Ce 3+ 5d–4f transition appeared around 320 nm with typically 40 ns decay time. By 241 Am 5.5 MeV α-ray irradiation, 0.1% doped one showed the highest scintillation light yield and the light yield monotonically decreased with Ce concentrations. Optically stimulated luminescence after X-ray irradiation was observed around 320 nm under 550 or 830 nm stimulation in all samples. As a result, intensities of optically stimulated luminescence were proportional to Ce concentrations. Consequently, scintillation and optically stimulated luminescence resulted to have a complementary relation in Ce-doped CaF 2 system. - Highlights: • Optical, scintillation, and OSL properties of Ce 0.1–20% doped CaF 2 were studied. • Scintillation light yield exhibited inverse proportionality to Ce concentrations. • OSL intensities showed proportionality to Ce concentrations. • Complementary relation of scintillation and OSL was experimentally confirmed

Vacuum Plasma Spraying W-coated Reduced Activation Structural Steels for Fusion Plasma Facing Components

Energy Technology Data Exchange (ETDEWEB)

Noh, Sanghoon; Kim, Tae Kyu [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2014-05-15

Tungsten (W) and its alloys are considered as candidate materials for plasma facing materials of the first wall and diverter components in fusion reactor systems because of high sputtering resistance and low tritium retention in a fusion environment. Therefore, it is considered that the joining between W and reduced activation structural steels, and its evaluation, are critical issues for the development of fusion reactors. However, the joining between these materials is a very challenging process because of significant differences in their physical properties, particularly the mismatch of coefficients of thermal expansion (CTE). For instance, the CTE of pure W is known to be about 4.3Χ10{sup -6}K{sup -1}; however, that of martensitic steels reaches over three times, about 12-14Χ10{sup -6}K{sup -1} at room temperature even up to 373K. Nevertheless, several joining techniques have been developed for joining between W and structural steels, such as a vapor deposition method, brazing and diffusion bonding. Meanwhile, vacuum plasma spraying (VPS) is supposed to be one of the prospective methods to fabricate a sufficient W layer on the steel substrates because of the coating of a large area with a relatively high fabricating rate. In this study, the VPS method of W powders on reduced activation steels was employed, and its microstructure and hardness distribution were investigated. ODS ferritic steels and F82H steel were coated by VPS-W, and the microstructure and hardness distribution were investigated. A microstructure analysis revealed that pure W was successfully coated on steel substrates by the VPS process without an intermediate layer, in spite of a mismatch of the CTE between dissimilar materials. After neutron irradiation, irradiation hardening significantly occurred in the VPSW. However, the hardening of VPS-W was lesser than that of bulk W irradiated HFIR at 773K. Substrate materials, ODS ferritic steels, and F82H steel, did not show irradiation hardening

Optically stimulated luminescence properties of Tm3+ doped KMgF3 fluoro perovskite

International Nuclear Information System (INIS)

Camargo, L.; Marcazzo, J.; Perez C, L.; Cruz Zaragoza, E.; Martinez O, S. A.

2017-10-01

In this work the optically stimulated luminescence (OSL) properties of undoped and Tm 3+ doped KMgF 3 fluoro perovskite have been investigated for the first time. OSL efficiency for stimulation with different wavelengths has been analyzed for each compound. The maximum OSL emission was found with blue light stimulation. The radioluminescence (Rl) spectra have shown two emission peaks at 455 and 360 nm, which can be ascribed to the 1 D 2 - 3 F 4 and 1 D 2 - 3 H 6 transitions of the Tm 3+ cations. It has been found that doping with Thulium 0.5 mol % renders the most intense OSL emission. Furthermore, several dosimetric properties such as OSL response as a function of dose, reproducibility of the OSL signal after several cycles of irradiation readout and the minimum detectable dose have been investigated. Finally, the OSL response of KMgF 3 : Tm 3+ has been compared to that of commercial Al 2 O 3 :C and the possible application of this fluoro perovskite to OSL dosimetry has been evaluated. (Author)

Self-ion Irradiation Damage of F/M and ODS steels

International Nuclear Information System (INIS)

Kang, Suk Hoon; Chun, Young-Bum; Noh, Sanghoon; Jang, Jinsung; Kim, Tae Kyu

2014-01-01

Oxide dispersion strengthened (ODS) ferritic steels are potential high-temperature materials that are stabilized by dispersed particles at elevated temperatures. These dispersed particles improve the tensile strength and creep rupture strength, they are expected to increase the operation temperature up to approximately 650 .deg. C and also enhance the energy efficiency of the fusion reactor. Some reports described that the nano-clusters are strongly resistant to coarsening by annealing up to 1000 .deg. C, and nanoclusters do not change after ion irradiation up to 0.7 dpa at 300 .deg. C. ODS steels will be inevitably exposed to neutron irradiation condition; the irradiation damages, creep and swelling are always great concern. The dispersed oxide particles are believed to determine the performance of the steel, even the radiation resistance. In this study, F/M and ODS model alloys of Korea Atomic Energy Research Institute (KAERI) were irradiated by Fe 3+ self-ion to emulate the neutron irradiation effect. In this study, Fe 3+ self-ion irradiation is used as means of introducing radiation damage in F/M steel and ODS steel. The ion accelerator named DuET (in Kyoto University, Japan) was used for irradiation of Fe 3+ ion by 6.4 MeV at 300 .deg. C. The maximum damage rate in F/M and ODS steels were estimated roughly 6 dpa. After radiation, point or line defects were dominantly observed in F/M steel, on the other hands, small circular cavities were typically observed in ODS steel. Nanoindentation is a useful tool to determine the irradiationinduced hardness change in the damage layer of ionirradiated iron base alloys

Structural, optical and electrochemical properties of F-doped vanadium oxide transparent semiconducting thin films

Energy Technology Data Exchange (ETDEWEB)

Mousavi, M.; Khorrami, G.H. [University of Bojnord, Department of Physics, Faculty of Basic Science, Bojnord (Iran, Islamic Republic of); Kompany, A. [Ferdowsi University of Mashhad, Department of Physics, Mashhad (Iran, Islamic Republic of); Yazdi, S.T. [Payame Noor University (PNU), Department of Physics, Tehran (Iran, Islamic Republic of)

2017-12-15

In this study, F-doped vanadium oxide thin films with doping levels up to 60 at % were prepared by spray pyrolysis method on glass substrates. To measure the electrochemical properties, some films were deposited on fluorine-tin oxide coated glass substrates. The effect of F-doping on the structural, electrical, optical and electrochemical properties of vanadium oxide samples was investigated. The X-ray diffractographs analysis has shown that all the samples grow in tetragonal β-V{sub 2}O{sub 5} phase structure with the preferred orientation of [200]. The intensity of (200) peak belonging to β-V{sub 2}O{sub 5} phase was strongest in the undoped vanadium oxide film. The scanning electron microscopy images show that the samples have nanorod- and nanobelt-shaped structure. The size of the nanobelts in the F-doped vanadium oxide films is smaller than that in the pure sample and the width of the nanobelts increases from 30 to 70 nm with F concentration. With increasing F-doping level from 10 to 60 at %, the resistivity, the transparency and the optical band gap decrease from 111 to 20 Ω cm, 70 to 50% and 2.4 to 2.36 eV, respectively. The cyclic voltammogram (CV) results show that the undoped sample has the most extensive CV and by increasing F-doping level from 20 to 60 at %, the area of the CV is expanded. The anodic and cathodic peaks in F-doped samples are stronger. (orig.)

Corrosion behavior of steels in liquid lead bismuth with low oxygen concentrations

Science.gov (United States)

Kurata, Yuji; Futakawa, Masatoshi; Saito, Shigeru

2008-02-01

Corrosion tests in pots were conducted to elucidate corrosion behavior of various steels in liquid lead-bismuth for 3000 h under the condition of an oxygen concentration of 5 × 10 -8 wt% at 450 °C and an oxygen concentration of 3 × 10 -9 wt% at 550 °C, respectively. Significant corrosion was not observed at 450 °C for ferritic/martensitic steels, F82H, Mod.9Cr-1Mo steel, 410SS, 430SS except 2.25Cr-1Mo steel. Pb-Bi penetration into steels and dissolution of elements into Pb-Bi were severe at 550 °C even for ferritic/martensitic steels. Typical dissolution attack occurred for pure iron both at 550 °C without surface Fe 3O 4 and at 450 °C with a thin Fe 3O 4 film. Ferritization due to dissolution of Ni and Cr, and Pb-Bi penetration were recognized for austenitic stainless steels, 316SS and 14Cr-16Ni-2Mo steel at both temperatures of 450 °C and 550 °C. The phenomena were mitigated for 18Cr-20Ni-5Si steel. In some cases oxide films could not be a corrosion barrier in liquid lead-bismuth.

Effects of impurity elements on mechanical properties and microstructures of reduced-activation ferritic/martensitic steels

Energy Technology Data Exchange (ETDEWEB)

Sawahata, A. [Ibaraki Univ., Graduate School of Science and Engineering, Hitachi (Japan); Tanigawa, H.; Shiba, K. [Japan Atomic Energy Agency, Naga-gun, Ibaraki-ken (Japan); Enomoto, M. [Ibaraki Univ., Dept. of Materials Science, Faculty of Engineering, Hitachi (Japan)

2007-07-01

Full text of publication follows: Reduced activation ferritic/martensitic steels (RAFs), such as F82H (Fe-8Cr-2W-0.2V- 0.04Ta-0.1C, in wt%), are one of the leading candidates for structural materials of fusion reactors. Impact property of F82H can be improved by adjusting the amount of tantalum or titanium concentration. On the other hand, it was reported by microstructure analyses of IEA steel that tantalum has a tendency to form oxides and causes a large dispersion of fracture toughness. In this study, the correlation between titanium or tantalum concentration and the impact property were reported focusing on difference in microstructure. Charpy impact test and microstructure analyses were carried out against modified F82H series of which titanium, nitrogen and tantalum composition were controlled. Charpy impact test results showed that the ductile-brittle transition temperature (DBTT) of T05A (0.05Ta- 0.0014N-steels. The size distribution analyses of oxides indicate that the number density of composite oxides in T05B was higher than in T05A. In addition, EDX analyses showed that composite oxides in T05B had a strong peak of titanium, but the peak were not detected in the oxides in T05A. These results suggest that titanium has a significant influence on the formation of oxides, and affects the impact property. The influence of tantalum concentration on the formation of these oxides and mechanical properties will be reported. (authors)

Depth profiling of hydrogen in ferritic/martensitic steels by means of a tritium imaging plate technique

International Nuclear Information System (INIS)

Otsuka, Teppei; Tanabe, Tetsuo

2013-01-01

Highlights: ► We applied a tritium imaging plate technique to depth profiling of hydrogen in bulk. ► Changes of hydrogen depth profiles in the steel by thermal annealing were examined. ► We proposed a release model of plasma-loaded hydrogen in the steel. ► Hydrogen is trapped at trapping sites newly developed by plasma loading. ► Hydrogen is also trapped at surface oxides and hardly desorbed by thermal annealing. -- Abstract: In order to understand how hydrogen loaded by plasma in F82H is removed by annealing at elevated temperatures in vacuum, depth profiles of plasma-loaded hydrogen were examined by means of a tritium imaging plate technique. Owing to large hydrogen diffusion coefficients in F82H, the plasma-loaded hydrogen easily penetrates into a deeper region becoming solute hydrogen and desorbs by thermal annealing in vacuum. However the plasma-loading creates new hydrogen trapping sites having larger trapping energy than that for the intrinsic sites beyond the projected range of the loaded hydrogen. Some surface oxides also trap an appreciable amount of hydrogen which is more difficult to remove by the thermal annealing

Electric field effect on the emission rate of H4F and H4S hole traps in InP

International Nuclear Information System (INIS)

Darwich, R.; Alek, B.

2010-01-01

The electric field effect on the emission rate enhancement of the H4 F and H4 S hole trap in highly Zn-doped InP has been examined using the deep level transient spectroscopy (DLTS) and double correlation DLTS (DDLTS). The DLTS and DDLTS results have been found to be in good agreement for low and intermediate electric fields, but they disagree for large field effect. Comparing our emission data with the theory, we have found that H4 F obeys the quantum model of phonon-assisted tunneling while H4 S follows the Poole-Frenkel model employing a three-dimensional screening coulombic potential. Our results show that the H4 S defect can be attributed to a charged (V p - Zn) complex. (author)

Luminescent properties of Ln3+ doped tellurite glasses containing AlF3

Science.gov (United States)

Walas, Michalina; Pastwa, Agata; Lewandowski, Tomasz; Synak, Anna; Gryczyński, Ignacy; Sadowski, Wojciech; Kościelska, Barbara

2016-09-01

The low-phonon energy tellurite glasses TeO2-BaO-Bi2O3 and TeO2-BaO-Bi2O3-AlF3 triply doped with Eu3+, Tb3+, Tm3+ ions in two different molar ratios were synthesized using melt-quenching technique. Their structure and luminescence properties were widely investigated by X-ray Diffraction (XRD), Differential Scanning Calorimetry (DSC), Fourier Transform Infrared Spectroscopy (FTIR) and Photoluminescence Spectroscopy (PL). The luminescence spectra of Eu3+, Tb3+, Tm3+ co-doped glasses show apart of the bands corresponding to the 4f-4f transitions of lanthanide ions also band corresponding to glass matrix. AlF3 doping increases emission intensity, although to improve overall emission color further studies on molar composition of samples and the molar ratio of the components should be carried out.

Deformation mechanisms in ferritic/martensitic steels and the impact on mechanical design

International Nuclear Information System (INIS)

Ghoniem, Nasr M.; Po, Giacomo; Sharafat, Shahram

2013-01-01

Structural steels for nuclear applications have undergone rapid development during the past few decades, thanks to a combination of trial-and-error, mechanism-based optimization, and multiscale modeling approaches. Deformation mechanisms are shown to be intimately related to mechanical design via dominant plastic deformation modes. Because mechanical design rules are mostly based on failure modes associated with plastic strain damage accumulation, we present here the fundamental deformation mechanisms for Ferritic/Martensitic (F/M) steels, and delineate their operational range of temperature and stress. The connection between deformation mechanisms, failure modes, and mechanical design is shown through application of design rules. A specific example is given for the alloy F82H utilized in the design of a Test Blanket Module (TBM) in the International Thermonuclear Experimental Reactor (ITER), where several constitutive equations are developed for design-related mechanical properties

Deformation mechanisms in ferritic/martensitic steels and the impact on mechanical design

Energy Technology Data Exchange (ETDEWEB)

Ghoniem, Nasr M., E-mail: ghoniem@seas.ucla.edu; Po, Giacomo; Sharafat, Shahram

2013-10-15

Structural steels for nuclear applications have undergone rapid development during the past few decades, thanks to a combination of trial-and-error, mechanism-based optimization, and multiscale modeling approaches. Deformation mechanisms are shown to be intimately related to mechanical design via dominant plastic deformation modes. Because mechanical design rules are mostly based on failure modes associated with plastic strain damage accumulation, we present here the fundamental deformation mechanisms for Ferritic/Martensitic (F/M) steels, and delineate their operational range of temperature and stress. The connection between deformation mechanisms, failure modes, and mechanical design is shown through application of design rules. A specific example is given for the alloy F82H utilized in the design of a Test Blanket Module (TBM) in the International Thermonuclear Experimental Reactor (ITER), where several constitutive equations are developed for design-related mechanical properties.

Superconducting Gap Symmetry of LaFeP(O,F Observed by Impurity Doping Effect

Directory of Open Access Journals (Sweden)

Shigeki Miyasaka

2016-08-01

Full Text Available We have investigated Mn, Co and Ni substitution effects on polycrystalline samples of LaFePO0.95F0.05 by resistivity and magnetoresistance measurements. In LaFe1-xMxPO0.95F0.05 (M = Mn, Co and Ni, the superconducting transition temperature (Tc monotonously decreases with increasing the impurity doping level of x. There is a clear difference of Tc suppression rates among Mn, Co and Ni doping cases, and the decreasing rate of Tc by Mn doping as a magnetic impurity is larger than those by the nonmagnetic doping impurities (Co/Ni. This result indicates that in LaFePO0.95F0.05, Tc is rapidly suppressed by the pair-breaking effect of magnetic impurities, and the pairing symmetry is a full-gapped s-wave. In the nonmagnetic impurity-doped systems, the residual resistivity in the normal state has nearly the same value when Tc becomes zero. The residual resistivity value is almost consistent with the universal value of sheet resistance for two-dimensional superconductors, suggesting that Tc is suppressed by electron localization in Co/Ni-doped LaFePO0.95F0.05.

Boron-doped cadmium oxide composite structures and their electrochemical measurements

Energy Technology Data Exchange (ETDEWEB)

Lokhande, B.J., E-mail: bjlokhande@yahoo.com [Lab of Smart Mtrls Supercapacitive and Energy Studies, School of Physical Sciences, Solapur University, Solapur 413255, Maharashtra (India); Ambare, R.C. [Lab of Smart Mtrls Supercapacitive and Energy Studies, School of Physical Sciences, Solapur University, Solapur 413255, Maharashtra (India); Mane, R.S. [School of Physical Sciences, Swami Ramanand Teerth Marathwada University, Nanded 431606 (India); Bharadwaj, S.R. [Chemistry Division, Bhabha Atomic Research Centre, Trombay, Mumbai 400085 (India)

2013-08-01

Graphical abstract: Conducting nano-fibrous 3% boron doped cadmium oxide thin films were prepared by SILAR and its super capacitive properties were studied. - Highlights: • Samples are of nanofibrous nature. • All samples shows pseudocapacitive behavior. • 3% B doped CdO shows good specific capacitance. • 3% B doped CdO shows maximum 74.93% efficiency at 14 mA/cm{sup 2}. • 3% B doped CdO shows 0.8 Ω internal resistance. - Abstract: Boron-doped and undoped cadmium oxide composite nanostructures in thin film form were prepared onto stainless steel substrates by a successive ionic layer adsorption and reaction method using aqueous solutions of cadmium nitrate, boric acid and 1% H{sub 2}O{sub 2}. As-deposited films were annealed at 623 K for 1 h. The X-ray diffraction study shows crystalline behavior for both doped and undoped films with a porous topography and nano-wires type architecture, as observed in SEM image. Wettability test confirms the hydrophilic surface with 58° contact angle value. Estimated band gap energy is around 1.9 eV. Electrochemical behavior of the deposited films is attempted in 1 M KOH electrolyte using cyclic voltammetry (CV), electrochemical impedance spectroscopy and galvanostatic charge–discharge tests. Maximum values of the specific capacitance, specific energy and specific power obtained for 3% B doped CdO film at 2 mV/s scan rate are 20.05 F/g, 1.22 Wh/kg and 3.25 kW/kg, respectively.

Origin of the high p-doping in F intercalated graphene on SiC

KAUST Repository

Cheng, Yingchun

2011-08-04

The atomic and electronic structures of F intercalated epitaxialgraphene on a SiC(0001) substrate are studied by first-principles calculations. A three-step fluorination process is proposed. First, F atoms are intercalated between the graphene and the SiC, which restores the Dirac point in the band structure. Second, saturation of the topmost Si dangling bonds introduces p-doping up to 0.37 eV. Third, F atoms bond covalently to the graphene to enhance the p-doping. Our model explains the highly p-doped state of graphene on SiC after fluorination [A. L. Walter et al., Appl. Phys. Lett. 98, 184102 (2011)].

Influence of SrF_2-doping in AlN ceramics on scintillation and dosimeter properties

International Nuclear Information System (INIS)

Kojima, Kaori; Okada, Go; Fukuda, Kentaro; Yanagida, Takayuki

2016-01-01

In this study, we synthesized undoped AlN and SrF_2-doped AlN (AlN-SrF_2) ceramics by Spark Plasma Sintering (SPS), and we characterized their optical, scintillation and dosimeter properties. The prepared undoped AlN ceramic had gray color and visually non-transparent whereas, with an addition of SrF_2, the transparency improved and became translucent. The measured in-line transmittance was approximately 0.2% at wavelengths longer than 500 nm. While the addition of SrF_2 decreased the scintillation intensity, the decay time was significantly fastened, which is a great advantage for fast photon counting-based measurements. Both the thermally-stimulated luminescence (TSL) and optically-stimulated luminescence (OSL) showed good linear response from the milli-gray range to over 10 Gy. The sensitivity seems to decrease by an addition of SrF_2 as it suppresses structural defect centers which are responsible for dosimeter properties. However, the main TSL glow peak position shifts to higher temperature with the addition of SrF_2, which indicates that inclusion of SrF_2 improves the TSL signal stability. - Highlights: • We synthesized undoped and SrF_2-doped AlN ceramics by Spark Plasma Sintering. • We evaluated scintillator and dosimeter properties of undoped and SrF_2-doped AlN. • By doping with SrF_2, the decay time is shortened. • By doping with SrF_2, the stability of TSL and OSL is improved.

Corrosion Protection of Steels by Conducting Polymer Coating

Directory of Open Access Journals (Sweden)

Toshiaki Ohtsuka

2012-01-01

Full Text Available The corrosion protection of steels by conducting polymer coating is reviewed. The conducting polymer such as polyaniline, polypyrrole, and polythiophen works as a strong oxidant to the steel, inducing the potential shift to the noble direction. The strongly oxidative conducting polymer facilitates the steel to be passivated. A bilayered PPy film was designed for the effective corrosion protection. It consisted of the inner layer in which phosphomolybdate ion, PMo12O3−40 (PMo, was doped and the outer layer in which dodecylsulfate ion (DoS was doped. The inner layer stabilized the passive oxide and the outer possessed anionic perm-selectivity to inhibit the aggressive anions such as chloride from penetrating through the PPy film to the substrate steel. By the bilayered PPy film, the steel was kept passive for about 200 h in 3.5% sodium chloride solution without formation of corrosion products.

Synergistic effects of F and Fe in co-doped TiO{sub 2} nanoparticles

Energy Technology Data Exchange (ETDEWEB)

Zhang, Yufei, E-mail: zhang.yu.fei@stu.xjtu.edu.cn; Shen, Huiyuan; Liu, Yanhua, E-mail: yhliu@mail.xjtu.edu.cn [Xi’an Jiaotong University, Department of Building Environment and Services Engineering, School of Human Settlements and Civil Engineering (China)

2016-03-15

TiO{sub 2} photocatalysts co-doped with F and Fe were synthesized by a sol–gel method. Synergistic effects of F and Fe in the co-doped TiO{sub 2} were verified by NH{sub 3} decomposition, X-ray diffraction (XRD), scanning electron microscopy (SEM), high-resolution transmission electron microscopy (HRTEM), X-ray photoelectron spectroscopy (XPS) and ultraviolet–visible (UV–Vis) absorption spectroscopy, and was analyzed by the simulation based on the density functional theory (DFT). The results from NH{sub 3} decomposition confirmed that the cooperation of F and Fe broadened the optical response of TiO{sub 2} to visible light region and also enhanced the photocatalytic activity of TiO{sub 2} under ultraviolet light. XRD patterns, SEM and HRTEM images showed that the co-doped samples were nanometric anatase with an average particle size of 25 nm. Co-doping with F and Fe inhibited the grain growth of TiO{sub 2} from anatase to rutile and resulted in a larger lattice defect. XPS analysis exhibited that the doped F and Fe atoms were into the TiO{sub 2} lattice. UV–Vis absorption spectra showed that its optical absorption edge was moved up to approximately 617 nm and its ultraviolet absorption was also enhanced. The DFT results indicated that the cooperation of Fe 3d and O 2p orbits narrowed the band gap of TiO{sub 2} and F 2p orbit widened the upper valence bands. The synergistic electron density around F and Fe in co-doped TiO{sub 2} was capable to enhance the photo-chemical stability of TiO{sub 2}.

Enhanced visible light photocatalytic degradation of methylene blue by F-doped TiO{sub 2}

Energy Technology Data Exchange (ETDEWEB)

Yu, Wei [Engineering Research Center for Nanophotonics and Advanced Instrument, Ministry of Education, Department of Physics, East China Normal University, Shanghai 200062 (China); Liu, Xinjuan, E-mail: lxj669635@126.com [Shanghai Nanotechnlogy Promotion Center, Shanghai 200237 (China); Center for Coordination Bond and Electronic Engineering, College of Materials Science and Engineering, China Jiliang University, Hangzhou 310018 (China); Pan, Likun, E-mail: lkpan@phy.ecnu.edu.cn [Engineering Research Center for Nanophotonics and Advanced Instrument, Ministry of Education, Department of Physics, East China Normal University, Shanghai 200062 (China); Li, Jinliang; Liu, Junying [Engineering Research Center for Nanophotonics and Advanced Instrument, Ministry of Education, Department of Physics, East China Normal University, Shanghai 200062 (China); Zhang, Jing; Li, Ping; Chen, Chen [Shanghai Nanotechnlogy Promotion Center, Shanghai 200237 (China); Sun, Zhuo [Engineering Research Center for Nanophotonics and Advanced Instrument, Ministry of Education, Department of Physics, East China Normal University, Shanghai 200062 (China)

2014-11-15

Graphical abstract: F-doped TiO2 is synthesized using a modified sol–gel method for visible photocatalytic degradation of MB with a high degradation rate of 91%. - Highlights: • F-doped TiO{sub 2} are synthesized using a modified sol–gel method. • The photocatalytic degradation of methylene blue by F-doped TiO{sub 2} is investigated. • A high methylene blue degradation rate of 91% is achieved under visible light irradiation. - Abstract: F-doped TiO{sub 2} (F-TiO{sub 2}) were successfully synthesized using a modified sol–gel method. The morphologies, structures, and photocatalytic performance in the degradation of methylene blue (MB) were characterized by scanning electron microscopy, transmission electron microscopy, X-ray diffraction, UV–vis absorption spectroscopy, and electrochemical impedance spectra, respectively. The results show that F-TiO{sub 2} exhibits an enhanced photocatalytic performance in the degradation of MB with a maximum degradation rate of 91% under visible light irradiation as compared with pure TiO{sub 2} (32%). The excellent photocatalytic activity is due to the contribution from the increased visible light absorption, promoted separation of photo-generated electrons and holes as well as enhanced photocatalytic oxidizing species with the doping of F in TiO{sub 2}.

Electrochemical depositions of fluorohydroxyapatite doped by Cu2+, Zn2+, Ag+ on stainless steel substrates

International Nuclear Information System (INIS)

Bir, F.; Khireddine, H.; Touati, A.; Sidane, D.; Yala, S.; Oudadesse, H.

2012-01-01

Fluoridated hydroxyapatite (FHA, Ca 10 (PO 4 ) 6 (OH) 2-x F x where 0 2+ , Cu 2+ , Ag + ) substituted fluoridated hydroxyapatite coatings (M-FHA) were deposited on the surface of medical grade 316L stainless steel samples by electrochemical deposition technique. The FHA coatings were co-substituted with antibacterial ions (Zn 2+ , Cu 2+ or Ag + ) by co-precipitation and ion-exchange methods. Characterization studies of coatings from X-ray diffraction (XRD), Scanning electron microscopy (SEM) and Energy dispersive X-ray spectroscopy (EDX) showed that the obtained layers are monophase crystals FHA and did not contain any discernible crystalline impurity. The particles of all samples are of nano size that gives thin layers. The surface morphology, microstructure and Ca/P atomic ratio of the FHA coatings can be regulated by varying electrolyte temperature. This later affects the porosity of the coating surface and the chemical compositions of the deposits. Quantitative elemental analysis indicates that the copper, zinc and silver ions are incorporated into the Fluorohydroxyapatite. The antimicrobial effects of doped fluorohydroxyapatite coatings against pathogen bacterial strains Staphylococcus aureus were tested in liquid media. The results are promising and demonstrated that all doped FHA samples exhibit excellent antimicrobial activity “in vitro” against the microorganism, so the antimicrobial properties of the coatings developed are improved.

Crystal growth and evaluation of scintillation properties of Eu and alkali-metal co-doped LiSrAlF{sub 6} single crystals for thermal neutron detector

Energy Technology Data Exchange (ETDEWEB)

Wakahara, Shingo; Yokota, Yuui; Yamaji, Akihiro; Fujimoto, Yutaka; Sugiyama, Makoto; Kurosawa, Shunsuke [Institute for Materials Research, Tohoku University, 2-1-1 Katahira, Aoba-ku, Sendai, Miyagi 980-8577 (Japan); Yanagida, Takayuki [New Industry Creation Hatchery Center (NICHe), 6-6-10 Aoba, Aramaki, Aoba-ku, Sendai, Miyagi 980-8579 (Japan); Pejchal, Jan [Institute for Materials Research, Tohoku University, 2-1-1 Katahira, Aoba-ku, Sendai, Miyagi 980-8577 (Japan); Institute of Physics AS CR, Cukrovarnicka 10, Prague 16253 (Czech Republic); Kawaguchi, Noriaki [Institute for Materials Research, Tohoku University, 2-1-1 Katahira, Aoba-ku, Sendai, Miyagi 980-8577 (Japan); Tokuyama, Co. Ltd., Shibuya 3-chome, Shibuya-ku, Tokyo 150-8383 (Japan); Fukuda, Kentaro [Tokuyama, Co. Ltd., Shibuya 3-chome, Shibuya-ku, Tokyo 150-8383 (Japan); Yoshikawa, Akira [Institute for Materials Research, Tohoku University, 2-1-1 Katahira, Aoba-ku, Sendai, Miyagi 980-8577 (Japan); New Industry Creation Hatchery Center (NICHe), 6-6-10 Aoba, Aramaki, Aoba-ku, Sendai, Miyagi 980-8579 (Japan)

2012-12-15

In recent work, Na co-doping have found to improve the light output of Eu doped LiCaAlF{sub 6} (Eu:LiCAF) for thermal neutron scintillator. We grew Eu 2% and alkali metal 1% co-doped LiSAF crystals by Micro-Pulling down method to understand the effect of alkali metal co-doping on scintillation properties and mechanism compared with LiCAF. In photo- and {alpha}-ray induced radio-luminescence spectra of the all grown crystals, the emissions from d-f transition of Eu{sup 2+} were observed. Without relation to excitation source, decay times of co-doped LiSAF were longer than Eu only doped one. The light yield of Na, K and Cs co-doped LiSAF under {sup 252}Cf neutron excitation were improved. Especially, K co-doped Eu:LiSAF reached 33200 ph/n, which outperformed Eu only doped one by approximately 20% (copyright 2012 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

H+ irradiation effect in Co-doped BaFe2As2 single crystals

International Nuclear Information System (INIS)

Nakajima, Y.; Tsuchiya, Y.; Taen, T.; Tamegai, T.; Kitamura, H.; Murakami, T.

2011-01-01

The effect of H + irradiation on the suppression of Tc in Co-doped BaFe 2 As 2 . H + irradiation introduces nonmagnetic scattering centers. Critical Scattering rate is much higher than that expected in s±-pairing scenario. We report the suppression of the critical temperature T c in single crystalline Ba(Fe 1-x Co x ) 2 As 2 at under-, optimal-, and over-doping levels by 3 MeV proton irradiation. T c decreases and residual resistivity increases monotonically with increasing the dose. The low-temperature resistivity does not show the upturn in contrast with the α-particle irradiated NdFeAs(O,F), which suggests that proton irradiation introduces nonmagnetic scattering centers. Critical scattering rates for all samples obtained by three different ways are much higher than that expected in s±-pairing scenario based on inter-band scattering due to antiferro-magnetic spin fluctuations.

Evaluation of Ce3+ and alkali metal ions Co-doped LiSrAlF6 crystalline scintillators

International Nuclear Information System (INIS)

Wakahara, Shingo; Yanagida, Takayuki; Fujimoto, Yutaka; Yokota, Yuui; Pejchal, Jan; Kurosawa, Shunsuke; Suzuki, Shotaro; Kawaguchi, Noriaki; Fukuda, Kentaro; Yoshikawa, Akira

2013-01-01

High scintillation efficiency of Eu-doped LiSrAlF 6 (LiSAF) and LiCaAlF 6 (LiCAF) codoped with alkali metal ions has been reported in our recent studies. Thus in this paper, we demonstrated the scintillation properties of 1% Ce-doped LiSAF crystals with 1% alkali metal ions co-doping to increase the light yield and understand the scintillation mechanism. The crystals showed intense emission band corresponding to the 5d-4f transition of Ce 3+ , and their light yields under thermal neutron excitation were higher than that of the Ce only doped crystal. Especially, the light yield of Ce–Na co-doped crystal exceeded about two times that of Ce only doped one. -- Highlights: ► Ce-doped and alkali metal co-doped LiSAF crystals were grown by μ-PD method. ► Alkali metal co-doped crystals showed higher light yield than Ce only doped crystal. ► Decay time of alkali metal co-doped LiSAF were longer than that of Ce only doped one

Effects of irradiation conditions and environment on the reflectivity of different steel mirrors for ITER diagnostics systems

International Nuclear Information System (INIS)

Hernandez, Teresa; Martin, Piedad; Fernandez, Pilar; Hodgson, Eric R.

2009-01-01

In this work possible degradation of the reflectivity for mirrors made from various steels subjected to ionizing radiation, at moderate temperature and in different environments (vacuum, air, or nitrogen) up to a total dose of 9 MGy, has been examined. Mirrors were prepared from conventional austenitic stainless steel (316L) and also reduced activation ferritic/martensitic (RAFM) steels (Eurofer, ODS-Eurofer, F82H), and the reflectivity studied from ultraviolet to near infrared, before and after different treatments. Under all conditions the austenitic steel mirrors only degrade slightly (<10%), however for the reduced activation steels important reflectivity degradation for wavelengths below 1000 nm are observed for the different conditions. Surface morphology and microstructure has been also investigated using scanning electron microscopy (SEM). The production of near surface nitrides is considered to be the possible cause of the optical degradation.

Advantage of TiF{sub 3} over TiCl{sub 3} as a dopant precursor to improve the thermodynamic property of Na{sub 3}AlH{sub 6}

Energy Technology Data Exchange (ETDEWEB)

Kang Xiangdong [Shenyang National Laboratory for Materials Science, Institute of Metal Research, Chinese Academy of Sciences, Shenyang 110016 (China); Wang Ping [Shenyang National Laboratory for Materials Science, Institute of Metal Research, Chinese Academy of Sciences, Shenyang 110016 (China)]. E-mail: pingwang@imr.ac.cn; Cheng Huiming [Shenyang National Laboratory for Materials Science, Institute of Metal Research, Chinese Academy of Sciences, Shenyang 110016 (China)

2007-03-15

The effect of the dopant anion on thermodynamic tailoring in TiF{sub 3}- and TiCl{sub 3}-doped Na{sub 3}AlH{sub 6} was investigated by pressure-composition desorption isotherm measurements. It was found that the dissociation pressure of the TiF{sub 3}-doped hydride was substantially higher than that of the TiCl{sub 3}-doped sample. This finding agrees well with the theoretically demonstrated thermodynamic modification arising upon F{sup -} substitution in the hydride lattice, thus providing direct experimental evidence to support functionality of F{sup -} anion.

Zn2+-Doped Polyaniline/Graphene Oxide as Electrode Material for Electrochemical Supercapacitors

Science.gov (United States)

Xu, Hui; Tang, Jing; Chen, Yong; Liu, Jian; Pu, Jinjuan; Li, Qi

2017-10-01

Electrodes based on Zn2+-doped polyaniline/graphene oxide (Zn2+/PANI/GO) were synthesized on stainless steel mesh substrates in H2SO4 solution via electrochemical codeposition. Different concentrations of graphene oxide (GO) were incorporated into the films to improve the electrochemical performance of the electrodes. Electrochemical properties of the films were tested by cyclic voltammetry, galvanostatic charge-discharge tests, and electrochemical impedance spectroscopy, in a three-electrode system. The maximum specific capacitance of the Zn2+/PANI/GO film with a GO concentration of 15 mg L-1 was found to be 1266 F g-1 at a scan rate of 3 mV s-1. This value was higher than that of a Zn2+ doped polyaniline (Zn2+/PANI) film (814 F g-1). The Zn2+/PANI/GO film also showed good cycling stability, retaining over 86% of its initial capacitance after 1000 cycles. These results indicate that the Zn2+/PANI/GO composites can be applied as high performance supercapacitor electrodes.

Intrinsic Defects and H Doping in WO3

KAUST Repository

Zhu, Jiajie

2017-01-18

WO3 is widely used as industrial catalyst. Intrinsic and/or extrinsic defects can tune the electronic properties and extend applications to gas sensors and optoelectonics. However, H doping is a challenge to WO3, the relevant mechanisms being hardly understood. In this context, we investigate intrinsic defects and H doping by density functional theory and experiments. Formation energies are calculated to determine the lowest energy defect states. O vacancies turn out to be stable in O-poor environment, in agreement with X-ray photoelectron spectroscopy, and O-H bond formation of H interstitial defects is predicted and confirmed by Fourier transform infrared spectroscopy.

Novel and easy access to highly luminescent Eu and Tb doped ultra-small CaF2, SrF2 and BaF2 nanoparticles - structure and luminescence.

Science.gov (United States)

Ritter, Benjamin; Haida, Philipp; Fink, Friedrich; Krahl, Thoralf; Gawlitza, Kornelia; Rurack, Knut; Scholz, Gudrun; Kemnitz, Erhard

2017-02-28

A universal fast and easy access at room temperature to transparent sols of nanoscopic Eu 3+ and Tb 3+ doped CaF 2 , SrF 2 and BaF 2 particles via the fluorolytic sol-gel synthesis route is presented. Monodisperse quasi-spherical nanoparticles with sizes of 3-20 nm are obtained with up to 40% rare earth doping showing red or green luminescence. In the beginning luminescence quenching effects are only observed for the highest content, which demonstrates the unique and outstanding properties of these materials. From CaF 2 :Eu10 via SrF 2 :Eu10 to BaF 2 :Eu10 a steady increase of the luminescence intensity and lifetime occurs by a factor of ≈2; the photoluminescence quantum yield increases by 29 to 35% due to the lower phonon energy of the matrix. The fast formation process of the particles within fractions of seconds is clearly visualized by exploiting appropriate luminescence processes during the synthesis. Multiply doped particles are also available by this method. Fine tuning of the luminescence properties is achieved by variation of the Ca-to-Sr ratio. Co-doping with Ce 3+ and Tb 3+ results in a huge increase (>50 times) of the green luminescence intensity due to energy transfer Ce 3+ → Tb 3+ . In this case, the luminescence intensity is higher for CaF 2 than for SrF 2 , due to a lower spatial distance of the rare earth ions.

Optically stimulated luminescence properties of Tm{sup 3+} doped KMgF{sub 3} fluoro perovskite

Energy Technology Data Exchange (ETDEWEB)

Camargo, L.; Marcazzo, J. [UNCPBA, Facultad de Ciencias Exactas, Instituto de Fisica Arroyo Seco, Gral. Pinto 399, B7000GHG Tandil, Buenos Aires (Argentina); Perez C, L.; Cruz Zaragoza, E. [UNAM, Instituto de Ciencias Nucleares, Apdo. Postal 70543, 04510 Ciudad de Mexico (Mexico); Martinez O, S. A., E-mail: jmarcass@exa.unicen.edu.ar [Universidad Pedagogica y Tecnologica de Colombia, Grupo de Fisica Nuclear Aplicada y Simulacion, Av. Central del Norte 39-115, 150003 Tunja, Bocaya (Colombia)

2017-10-15

In this work the optically stimulated luminescence (OSL) properties of undoped and Tm{sup 3+} doped KMgF{sub 3} fluoro perovskite have been investigated for the first time. OSL efficiency for stimulation with different wavelengths has been analyzed for each compound. The maximum OSL emission was found with blue light stimulation. The radioluminescence (Rl) spectra have shown two emission peaks at 455 and 360 nm, which can be ascribed to the {sup 1}D{sub 2}-{sup 3}F{sub 4} and {sup 1}D{sub 2}-{sup 3}H{sub 6} transitions of the Tm{sup 3+} cations. It has been found that doping with Thulium 0.5 mol % renders the most intense OSL emission. Furthermore, several dosimetric properties such as OSL response as a function of dose, reproducibility of the OSL signal after several cycles of irradiation readout and the minimum detectable dose have been investigated. Finally, the OSL response of KMgF{sub 3}: Tm{sup 3+} has been compared to that of commercial Al{sub 2}O{sub 3}:C and the possible application of this fluoro perovskite to OSL dosimetry has been evaluated. (Author)

Superior catalytic effect of TiF3 over TiCl3 in improving the hydrogen sorption kinetics of MgH2: Catalytic role of fluorine anion

International Nuclear Information System (INIS)

Ma, L.-P.; Kang, X.-D.; Dai, H.-B.; Liang, Y.; Fang, Z.-Z.; Wang, P.-J.; Wang, P.; Cheng, H.-M.

2009-01-01

TiF 3 shows a superior catalytic effect over TiCl 3 in improving the hydrogen sorption kinetics of MgH 2 . Combined phase analysis and microstructure characterization suggest that both titanium halide additives react with host MgH 2 in a similar way. However, systematic X-ray photoelectron spectroscopy studies reveal that the incorporated fluorine (F) differs significantly from its analog chlorine (Cl) in terms of bonding state. The asymmetry of F 1s spectra and the sputtering-induced peak shift suggest that, in addition to the Mg-F bond, a new Ti-F-Mg bonding is formed in the TiF 3 -doped MgH 2 . In contrast, only one stable binding state of Cl is identified in the form of MgCl 2 for the TiCl 3 -doped MgH 2 . In combination with the designed experiments, these findings suggest that the generation of active F-containing species may be responsible for the advantage of TiF 3 over TiCl 3 in improving both the absorption and desorption kinetics of MgH 2 . Fundamentally, it emphasizes the functionality of F anion in tuning the activity of compound catalyst

Hole doping by pressure on the 1111 pnictides CaFeAsF and SrFeAsF

International Nuclear Information System (INIS)

Freitas, Daniele C; Sow, Amadou; Núñez-Regueiro, Manuel; Garbarino, Gastón; Weht, Ruben; Zhu, Xiyu; Han, Fei; Cheng, Peng; Ju, Jing; Hu Wen, Hai

2014-01-01

We determine the pressure phase diagram of the 1111 compounds CaFeAsF and SrFeAsF, up to 20 GPa and down to 4 K by electrical resistivity measurements and the change of structure up to 40 GPa at room temperature. The antiferromagnetic transition temperature, as determined by the derivative peak, shows a minimum at ∼5 GPa (10 GPa) for the Ca (Sr) compound. For CaFeAsF, superconductivity appears at this minimum, coincident with the development of a previously reported monoclinic phase. For SrFeAsF, where the orthorhombic and the monoclinic phase were reported to coexist, superconductivity exists above P≥1 GPa. Both phase diagrams can be scaled by a shift of ∼10 GPa pressure at which the volume of SrFeAsF and that of CaFeAsF at ambient pressure coincide. The difference of our phase diagram with that of electron-doped 1111 samples is accounted for by hole doping under pressure, which we verified through electron band structure calculations. (papers)

Sodium pool combustion test for small-scale leakage. Run-F7-4 and Run-F8-2

International Nuclear Information System (INIS)

Futagami, Satoshi; Ohno, Shuji

2003-06-01

Since 1998, the test (Run-F7 series) was performed to acquire the fundamental knowledge about the sodium pool growth and floor liner temperature in the case of small-scale leakage of sodium. And the test (Run-F8 series) was performed to know the floor liner material corrosion mechanism under high moisture conditions. In both test series, those influences are investigated by making the rate of sodium leakage, and moisture conditions of supply air into main parameters. As the last test, (1) Run-F7-4 (June 28, 2000) and (2) Run-F8-2 (January 26, 2000) were carried out. The conclusion of the following which receives sodium small-scale leakage (about 10 kg/h) was obtained from these experiments and the result of old Run-F7 and Run-F8 series. The peak temperature of a catch pan tends to become lower with decrease of sodium leak rate. Moreover, height of leak point and moisture conditions also become the factor which raises the catch pan peak temperature. Although it grows up in proportion [almost]to time in early stages of leakage about growth of a sodium pool, growth stops during the leakage. Moreover, the final growth area is mostly proportional to the rate of sodium leakage. It was suggested by the measured value of catch pan corrosion thickness and a material analysis result that the dominant corrosion mechanism was relatively slow Na-Fe double oxidization type corrosion even under the high moisture condition of 4.6 to 4.8%. And the chemical analysis result of a deposits also suggested that the catch pan material was in the environment in which molten salt type corrosion was not easy to occur. (author)

Hydrogen permeation through steel coated with erbium oxide by sol-gel method

International Nuclear Information System (INIS)

Yao Zhenyu; Suzuki, Akihiro; Levchuk, Denis; Chikada, Takumi; Tanaka, Teruya; Muroga, Takeo; Terai, Takayuki

2009-01-01

Er 2 O 3 coating is formed on austenitic stainless steel 316ss by sol-gel method. The results showed good crystallization of coating by baking in high purity flowing-argon at 973 K, and indicated that a little oxygen in baking atmosphere is necessary to crystallization of coating. The best baking temperature could be thought as 973 K, to get good crystallization of coating and avoid strong oxidation of steel substrate. The deuterium permeation test was performed for coated and bare 316ss, to evaluate the property of Er 2 O 3 sol-gel coating as a potential tritium permeation barrier. In this study, the deuterium permeability of coated 316ss is about 1-2 orders of magnitude lower than that of bare 316ss, and is about 2-3 orders of magnitude than the referred data of bare Eurofer97 and F82H martensitic steel.

Crystal growth and luminescence properties of Pr-doped LuLiF4 single crystal

International Nuclear Information System (INIS)

Sugiyama, Makoto; Yanagida, Takayuki; Yokota, Yuui; Kurosawa, Shunsuke; Fujimoto, Yutaka; Yoshikawa, Akira

2013-01-01

0.1, 1, and 3% Pr (with respect to Lu) doped LuLiF 4 (Pr:LuLiF 4 ) single crystals were grown by the micro-pulling-down (μ-PD) method. Transparency of the grown crystals was higher than 70% in the visible wavelength region with some absorption bands due to Pr 3+ 4f-4f transitions. Intense absorption bands related with the Pr 3+ 4f-5d transitions were observed at 190 and 215 nm. In radioluminescence spectra, Pr 3+ 5d-4f emissions were observed at 220, 240, 340, and 405 nm. In the pulse height spectra recorded under 137 Cs γ-ray excitation, the Pr 3% doped sample showed the highest light yield of 2050 photons/MeV and the scintillation decay time of it exhibited 23 and 72 ns also excited by 137 Cs γ-ray. -- Highlights: ► 0.1, 1, and 3% Pr-doped LuLiF 4 single crystals were grown by the μ-PD method. ► Pr 3+ 5d-4f emission peaks appeared at 220, 240, 340, and 405 nm ► The Pr 3%:LuLiF 4 crystal showed the highest light yield of 2050 photons/MeV

Dynamic mechanical properties of reduced activation ferritic steels

International Nuclear Information System (INIS)

Hirose, T.; Kohyama, A.; Tanigawa, H.; Ando, M.; Jitsukawa, S.

2003-01-01

A fatigue test method by a miniaturized hourglass-shaped fatigue specimen has been developed for International Fusion Materials Irradiation Facility (IFMIF) and sufficient potential as the alternative to a conventional large specimen was presented. Furthermore, focused ion beam micro- sampling method was successfully applied to microstructural analysis on fracture process. Where, the effects of displacement damage and transmutation helium on the fatigue properties of Reduced Activation Ferritic/Martensitic Steels, RAFs, were investigated. Neutron irradiation and helium-ion-implantation at ambient temperature caused radiation hardening to degrade fatigue lifetime of F82H steel. Microstructural analysis revealed that local brittle fractures occurred at early stage of fatigue tests was the origin of the degradation.. No significant difference in fatigue life degradation was detected with and without implanted helium. This result suggests that 100 appm helium implanted has no impact on fracture life time under neutron irradiation. (author)

Electrochemical Corrosion Behavior of Carbon Steel and Hot Dip Galvanized Steel in Simulated Concrete Solution with Different pH Values

Directory of Open Access Journals (Sweden)

Wanchen XIE

2017-08-01

Full Text Available Hot dip galvanizing technology is now widely used as a method of protection for steel rebars. The corrosion behaviors of Q235 carbon steel and hot galvanized steel in a Ca(OH2 solution with a pH from 10 to 13 was investigated by electrode potential and polarization curves testing. The results indicated that carbon steel and hot galvanized steel were all passivated in a strong alkaline solution. The electrode potential of hot dip galvanized steel was lower than that of carbon steel; thus, hot dip galvanized steel can provide very good anodic protection for carbon steel. However, when the pH value reached 12.5, a polarity reversal occurred under the condition of a certain potential. Hot dip galvanized coating became a cathode, and the corrosion of carbon steel accelerated. The electrochemical behaviors and passivation abilities of hot dip galvanized steel and carbon steel were affected by pH. The higher the pH value was, the more easily they were passivated.DOI: http://dx.doi.org/10.5755/j01.ms.23.3.16675

Sorption properties and reversibility of Ti(IV) and Nb(V)-fluoride doped-Ca(BH4)2-MgH2 system

International Nuclear Information System (INIS)

Bonatto Minella, Christian; Garroni, Sebastiano; Pistidda, Claudio; Baró, Maria Dolors; Gutfleisch, Oliver; Klassen, Thomas; Dornheim, Martin

2015-01-01

Highlights: • Faster desorption reaction for doped materials vs. the pure composite system. • Kinetic improvement concerning re-hydrogenation reaction showed by the addition of NbF 5 . • Full characterization of the de-hydrogenation reaction pathway by means of both SR-PXD and 11 B{ 1 H} MAS-NMR. • Study of the evolution of the chemical state of the additives upon both milling and sorption reactions. - Abstract: In the last decade, alkaline and alkaline earth metal tetrahydroborates have been the focuses of the research due to their high gravimetric and volumetric hydrogen densities. Among them, Ca(BH 4 ) 2 and the Ca(BH 4 ) 2 + MgH 2 reactive hydride composites (RHC), were calculated to have the ideal thermodynamic properties which fall within the optimal range for mobile applications. In this study, the addition of NbF 5 or TiF 4 to the Ca(BH 4 ) 2 + MgH 2 reactive hydride composite system was attempted aiming to obtain a full reversible system with the simultaneous suppression of CaB 12 H 12 . Structural characterization of the specimens was performed by means of in-situ Synchrotron Radiation Powder X-ray diffraction (SR-PXD) and 11 B{ 1 H} Solid State Magic Angle Spinning-Nuclear Magnetic Resonance (MAS-NMR). The evolution of the chemical state of the Nb- and Ti-based additives was monitored by X-ray Absorption Near Edge Structure (XANES). The addition of NbF 5 or TiF 4 to the Ca(BH 4 ) 2 + MgH 2 system have not suppressed completely the formation of CaB 12 H 12 and only a slight improvement concerning the reversible reaction was displayed just in the case of Nb-doped composite material

Heavily doped n-type a-IGZO by F plasma treatment and its thermal stability up to 600 °C

Science.gov (United States)

Um, Jae Gwang; Jang, Jin

2018-04-01

We report the electrical properties and thermal stability of heavily doped, amorphous indium-gallium-zinc-oxide (a-IGZO) treated with fluorine (F) plasma. When the F doping concentration in a-IGZO is 17.51 × 1021/cm-3, the a-IGZO exhibits a carrier concentration of 6 × 1019 cm-3, a resistivity of 3 × 10-3 Ω cm, and a Hall mobility of 20 cm2/V s. This indicates that F is a suitable n-type dopant in a-IGZO. The similarity of the ionic radius of F to that of oxygen (O) allows substitutional doping by replacing O with F or the occupation of the oxygen vacancy (VO) site by F and consequent reduction in defect density. The semiconducting property of a-IGZO can change into metallic behavior by F doping. The defect passivation by F incorporation is confirmed by the XPS depth profile, which reveals the significant reduction in the VO concentration due to the formation of In-F bonds. The heavily doped a-IGZO exhibits thermally stable conductivity up to 600 °C annealing and thus can be widely used for the ohmic contact of a-IGZO devices.

Characterization and corrosion behavior of F6NM stainless steel treated in high temperature water

Science.gov (United States)

Li, Zheng-yang; Cai, Zhen-bing; Yang, Wen-jin; Shen, Xiao-yao; Xue, Guo-hong; Zhu, Min-hao

2018-03-01

F6NM martensitic stainless steel was exposed to 350 °C water condition for 500, 1500, and 2500 h to simulate pressurized water reactor (PWR) condition. The characterization and corrosion behavior of the oxide film were investigated. Results indicate that the exposed steel surface formed a double-layer oxide film. The outer oxide film is Fe-rich and contains two type oxide particles. However, the inner oxide film is Cr-rich, and two oxide films, whose thicknesses increase with increasing exposure time. The oxide film reduces the corrosion behavior because the outer oxide film has many crack and pores. Finally, the mechanism and factors affecting the formation of the oxide film were investigated.

Highly efficient electrochemical degradation of perfluorooctanoic acid (PFOA) by F-doped Ti/SnO{sub 2} electrode

Energy Technology Data Exchange (ETDEWEB)

Yang, Bo, E-mail: boyang@szu.edu.cn [Department of Environmental Engineering, College of Chemistry and Chemical Engineering, Shenzhen University, Shenzhen 518060 (China); School of Environment, POPs Research Center, Tsinghua University, Beijing 100084 (China); Jiang, Chaojin [Department of Environmental Engineering, College of Chemistry and Chemical Engineering, Shenzhen University, Shenzhen 518060 (China); Yu, Gang, E-mail: yg-den@tsinghua.edu.cn [School of Environment, POPs Research Center, Tsinghua University, Beijing 100084 (China); Zhuo, Qiongfang [South China Institute of Environmental Sciences, The Ministry of Environment Protection, Guangzhou 510655 (China); Deng, Shubo [School of Environment, POPs Research Center, Tsinghua University, Beijing 100084 (China); Wu, Jinhua [School of Environment and Energy, South China University of Technology, Guangzhou 510006 (China); Zhang, Hong [Department of Environmental Engineering, College of Chemistry and Chemical Engineering, Shenzhen University, Shenzhen 518060 (China)

2015-12-15

Highlights: • A novel SnO{sub 2} electrode is prepared by F doping instead of the traditional Sb doping. • SnF{sub 4} as single-source precursor is used to fabricate the long-life Ti/SnO{sub 2}–F anode. • F-doped Ti/SnO{sub 2} anode possesses high OEP and decomposition ability for PFOA. • Further mechanistic detail of PFOA degradation on Ti/SnO{sub 2}–F electrode is proposed. - Abstract: The novel F-doped Ti/SnO{sub 2} electrode prepared by SnF{sub 4} as the single-source precursor was used for electrochemical degradation of aqueous perfluorooctanoic acid (PFOA). Higher oxidation reactivity and significantly longer service life were achieved for Ti/SnO{sub 2}–F electrode than Ti/SnO{sub 2}–X (X = Cl, Br, I, or Sb) electrode, which could decomposed over 99% of PFOA (50 mL of 100 mg L{sup −1}) within 30-min electrolysis. The property of Ti/SnO{sub 2}–F electrode and its electrooxidation mechanism were investigated by XRD, SEM–EDX, EIS, LSV, and interfacial resistance measurements. We propose that the similar ionic radii of F and O as well as strong electronegativity of F caused its electrochemical stability with high oxygen evolution potential (OEP) and smooth surface to generate weakly adsorbed ·OH. The preparation conditions of electrode were also optimized including F doping amount, calcination temperature, and dip coating times, which revealed the formation process of electrode. Additionally, the major mineralization product, F{sup −}, and low concentration of shorter chain perfluorocarboxylic acids (PFCAs) were detected in solution. So the reaction pathway of PFOA electrooxidation was proposed by intermediate analysis. These results demonstrate that Ti/SnO{sub 2}–F electrode is promising for highly efficient treatment of PFOA in wastewater.

Thermally and optically stimulated radiative processes in Eu and Y co-doped LiCaAlF6 crystal

International Nuclear Information System (INIS)

Fukuda, Kentaro; Yanagida, Takayuki; Fujimoto, Yutaka

2015-01-01

Yttrium co-doping was attempted to enhance dosimeter performance of Eu doped LiCaAlF 6 crystal. Eu doped and Eu, Y co-doped LiCaAlF 6 were prepared by the micro-pulling-down technique, and their dosimeter characteristics such as optically stimulated luminescence (OSL) and thermally stimulated luminescence (TSL) were investigated. By yttrium co-doping, emission intensities of OSL and TSL were enhanced by some orders of magnitude. In contrast, scintillation characteristics of yttrium co-doped crystal such as intensity of prompt luminescence induced by X-ray and light yield under neutron irradiation were degraded

Modifying the size and uniformity of upconversion Yb/Er:NaGdF4 nanocrystals through alkaline-earth doping.

Science.gov (United States)

Lei, Lei; Chen, Daqin; Huang, Ping; Xu, Ju; Zhang, Rui; Wang, Yuansheng

2013-11-21

NaGdF4 is regarded as an ideal upconversion (UC) host material for lanthanide (Ln(3+)) activators because of its unique crystal structure, high Ln(3+) solubility, low phonon energy and high photochemical stability, and Ln(3+)-doped NaGdF4 UC nanocrystals (NCs) have been widely investigated as bio-imaging and magnetic resonance imaging agents recently. To realize their practical applications, controlling the size and uniformity of the monodisperse Ln(3+)-doped NaGdF4 UC NCs is highly desired. Unlike the routine routes by finely adjusting the multiple experimental parameters, herein we provide a facile and straightforward strategy to modify the size and uniformity of NaGdF4 NCs via alkaline-earth doping for the first time. With the increase of alkaline-earth doping content, the size of NaGdF4 NCs increases gradually, while the size-uniformity is still retained. We attribute this "focusing" of size distribution to the diffusion controlled growth of NaGdF4 NCs induced by alkaline-earth doping. Importantly, adopting the Ca(2+)-doped Yb/Er:NaGdF4 NCs as cores, the complete Ca/Yb/Er:NaGdF4@NaYF4 core-shell particles with excellent size-uniformity can be easily achieved. However, when taking the Yb/Er:NaGdF4 NCs without Ca(2+) doping as cores, they could not be perfectly covered by NaYF4 shells, and the obtained products are non-uniform in size. As a result, the UC emission intensity of the complete core-shell NCs increases by about 30 times in comparison with that of the cores, owing to the effective surface passivation of the Ca(2+)-doped cores and therefore protection of Er(3+) in the cores from the non-radiative decay caused by surface defects, whereas the UC intensity of the incomplete core-shell NCs is enhanced by only 3 times.

(Zn-doped PVA)/n-4H-SiC (MPS)

Indian Academy of Sciences (India)

2018-05-23

May 23, 2018 ... A comparative study on dielectric behaviours of Au/(Zn-doped. PVA)/n-4H-SiC .... To form MPS structures, the prepared PVA (Zn nanoparticle- doped) ..... 95 2885. [26] MacCallum J R and Vincent C A 1989 Polymer electrolyte.

Embrittlement of irradiated ferritic/martensitic steels in the absence of irradiation hardening

Energy Technology Data Exchange (ETDEWEB)

Klueh, R.L. [Oak Ridge Noational Laboratory, TN (United States); Shiba, K. [Japan Atomic Energy Agency, Tokai-mura, Naga-gun, Ibaraki-ken (Japan); Sokolov, M. [Oak Ridge National Laboratory, Materials Science and Technology Div., TN (United States)

2007-07-01

Full text of publication follows: Neutron irradiation of 9-12% Cr ferritic/martensitic steels below 425-450 deg. C produces microstructural defects that cause an increase in yield stress and ultimate tensile strength. This irradiation hardening causes embrittlement, which is observed in Charpy impact and toughness tests as an increase in ductile-brittle transition temperature (DBTT). Based on observations that show little change in strength in these steels irradiated above 425-450 deg. C, the general conclusion has been that no embrittlement occurs above this irradiation-hardening temperature regime. In a recent study of F82H steel irradiated at 300, 380, and 500 deg. C, irradiation hardening-an increase in yield stress-was observed in tensile specimens irradiated at the two lower temperatures, but no change was observed for the specimens irradiated at 500 deg. C. As expected, an increase in DBTT occurred for the Charpy specimens irradiated at 300 and 380 deg. C. However, there was an unexpected increase in the DBTT of the specimens irradiated at 500 deg. C. The observed embrittlement was attributed to the irradiation-accelerated precipitation of Laves phase. This conclusion was based on results from a detailed thermal aging study of F82H, in which tensile and Charpy specimens were aged at 500, 550, 600, and 650 deg. C to 30,000 h. These studies indicated that there was a decrease in yield stress at the two highest temperatures and essentially no change at the two lowest temperatures. Despite the strength decrease or no change, the DBTT increased for Charpy specimens irradiated at all four temperatures. Precipitates were extracted from thermally aged specimens, and the amount of precipitate was correlated with the increase in transition temperature. Laves phase was identified in the extracted precipitates by X-ray diffraction. Earlier studies on conventional elevated-temperature steels also showed embrittlement effects above the irradiation-hardening temperature

An investigation of the Nb doping effect on structural, morphological, electrical and optical properties of spray deposited F doped SnO2 films

Science.gov (United States)

Turgut, G.; Keskenler, E. F.; Aydın, S.; Yılmaz, M.; Doǧan, S.; Düzgün, B.

2013-03-01

F and Nb + F co-doped SnO2 thin films were deposited on glass substrates by the spray pyrolysis method. The microstructural, morphological, electrical and optical properties of the 10 wt% F doped SnO2 (FTO) thin films were investigated specifically for niobium (Nb) doping in the range of 0-4 at.% with 1 at.% steps. As shown by the x-ray diffraction patterns, the films exhibited a tetragonal cassiterite structure with (200) preferential orientation. It was observed that grain sizes of the films for (200) and (301) peaks depended on the Nb doping concentration and varied in the range of 25.11-32.19 and 100.6-183.7 nm, respectively. The scanning electron microscope (SEM) micrographs showed that the FTO films were made of small pyramidal grains, while doubly doped films were made of small pyramidal grains and big polyhedron grains. From electrical studies, although 1 at.% Nb doped FTO films have the lowest sheet resistance and resistivity values, the highest figure-of-merit and optical band gap values obtained for FTO films were 16.2 × 10-2 Ω-1 and 4.21 eV, respectively. Also, infrared reflectivity values of the films were in the range of 97.39-98.98%. These results strongly suggest that these films are an attractive candidate for various optoelectronic applications and for photothermal conversion of solar energy.

Effects of heat treatment on mechanical properties of h13 steel

Science.gov (United States)

Guanghua, Yan; Xinmin, Huang; Yanqing, Wang; Xingguo, Qin; Ming, Yang; Zuoming, Chu; Kang, Jin

2010-12-01

Heat treatment on the mechanical properties of H13 hot working die steel for die casting is discussed. The H13 steel for die casting was treated by different temperatures of vacuum quenching, tempering, and secondary tempering to investigate its mechanical properties. Strength, plasticity, hardness, and impact toughness of the H13 hot working die steel for die casting were measured. Microstructure, grain size, and carbide particle size after heat treatment have a great impact on the mechanical properties of H13 hot working die steel for die casting. The microstructure of the H13 was analyzed by scanning electron microscopy (SEM) and by a metallographic microscope. It is found that H13 exhibits excellent mechanical properties after vacuum quenching at 1050°C and twice tempering at 600°C.

Origin of the high p-doping in F intercalated graphene on SiC

KAUST Repository

Cheng, Yingchun; Kaloni, T. P.; Huang, G. S.; Schwingenschlö gl, Udo

2011-01-01

and the SiC, which restores the Dirac point in the band structure. Second, saturation of the topmost Si dangling bonds introduces p-doping up to 0.37 eV. Third, F atoms bond covalently to the graphene to enhance the p-doping. Our model explains the highly p

F-doped VO2 nanoparticles for thermochromic energy-saving foils with modified color and enhanced solar-heat shielding ability.

Science.gov (United States)

Dai, Lei; Chen, Shi; Liu, Jianjun; Gao, Yanfeng; Zhou, Jiadong; Chen, Zhang; Cao, Chuanxiang; Luo, Hongjie; Kanehira, Minoru

2013-07-28

F-doped VO2 (M1) nanoparticles were prepared via one-pot hydrothermal synthesis. The F-doping can minimise the size of the VO2 (M1) nanoparticles, induce a homogeneous size distribution and effectively decrease the phase transition temperature to 35 °C at 2.93% F in VO2. VO2 smart glass foils obtained by casting these nanoparticles exhibit excellent thermochromism in the near-infrared region, which suggests that these foils can be used for energy-efficient glass. Compared to a pure VO2 foil, the 2.93% F-doped VO2 foil exhibits an increased solar-heat shielding ability (35.1%) and a modified comfortable colour, while still retaining an excellent solar modulation ability (10.7%) and an appropriate visible transmittance (48.7%). The F-doped VO2 foils are the first to simultaneously meet the requirements of a reduced phase transition temperature, diluted colour and excellent thermochromic properties, and these properties make the further improved F-doped VO2 foils suitable for commercial applications in energy efficient glass.

Synthesis and characterization of Er3+ doped CaF2 nanoparticles

International Nuclear Information System (INIS)

Zhi Guanglin; Song Jinghong; Mei Bingchu; Zhou Weibing

2011-01-01

Highlights: → Er 3+ :CaF 2 nanoparticles were synthesized by co-precipitation method with particle size of 8-36 nm. → Increasing dopant concentration increases lattice constants and decreases grain size. → Annealing treatment has a remarkable effect on luminescence properties. → Luminescence intensity decrease with the increasing of the dopant concentration. - Abstract: Er 3+ doped CaF 2 nanoparticles were synthesized by a chemical co-precipitation method. Effect of the dopant concentrations on the structure and optical properties of the CaF 2 nanoparticles was investigated. The X-ray powder diffraction and transmission electron microscopy analysis was used to characterize the structure and morphology of the nanoparticles. The nanoparticles with different dopant concentration exhibited a sphere-like morphology with diameters of about 8-36 nm. The incorporation of Er 3+ ions into CaF 2 resulted in the decrease in grain size and deterioration of crystallinity, but enlarged the lattice constants of CaF 2 . Additional annealing treatment at 400 deg. C to the prepared CaF 2 removed the NO 3 - and OH - groups adsorbed on the particles' surfaces, and improved the optical properties of the nanoparticles. The fluorescence intensity, with a maximum at approximately 0.4 mol%, decreased with the increase in doping concentration because of concentration quenching.

Synthesis of nanocrystalline LaF3 doped silica glasses by hydrofluoric acid catalyzed sol–gel process

International Nuclear Information System (INIS)

Nagayama, Shuhei; Kajihara, Koichi; Kanamura, Kiyoshi

2012-01-01

Highlights: ► Silica glasses doped by LaF 3 nanocrystals are obtained by HF-catalyzed sol–gel method. ► The processing time (∼1 week) is much shorter than that of previous studies. ► The uptake of SiF groups in the glass matrix greatly reduces the SiOH concentration. ► Effects of sintering conditions and properties of Er 3+ -doped samples are presented. - Abstract: Silica glasses doped with LaF 3 nanocrystals were prepared by HF-catalyzed sol–gel method. HF was used both as fluorine source and as catalyst of the sol–gel reaction, making it possible to shorten the processing time with reducing the concentration of SiOH groups to ∼10 18 cm −3 . The resultant glasses are transparent at visible spectral range, and the optical loss at the ultraviolet absorption edge is dominated by the Rayleigh scattering from LaF 3 crystallites. The size of LaF 3 crystallites increases with an increase in the sintering temperature and time, and is smaller than ∼40 nm in samples showing good visible transparency. Green upconversion photoluminescence is observed in an Er 3+ -doped sample under excitation at 980 nm.

Upconversion emission and cathodoluminescence of Er"3"+-doped NaYbF_4 nanoparticles for low-temperature thermometry and field emission displays

International Nuclear Information System (INIS)

Du, Peng; Yu, Jae Su; Luo, Laihui

2017-01-01

The Er"3"+-doped NaYbF_4 nanoparticles were fabricated by a hydrothermal method. The green and red emissions located at around 525, 542 and 657 nm corresponding to the "2H_1_1_/_2 → "4I_1_5_/_2, "4S_3_/_2 → "4I_1_5_/_2 and "4F_9_/_2 → "4I_1_5_/_2 transitions of Er"3"+ ions, respectively, were observed when pumped at 980 nm light. Furthermore, with the help of the fluorescence intensity ratio technique, the thermometric properties of as-prepared products from the thermally coupled "2H_1_1_/_2 and "4S_3_/_2 levels of Er"3"+ ions were studied by analyzing temperature-dependent upconversion (UC) emission spectra. The maximum sensitivity for the Er"3"+-doped NaYbF_4 nanoparticles was found to be around 0.0043 K"- "1 with a temperature range of 93-293 K. In addition, the cathodoluminescence (CL) spectrum of the synthesized nanoparticles was nearly the same as the UC emission spectrum and the CL emission intensity did not exhibit saturation with the increase of accelerating voltage and filament current. (orig.)

Impurity Antimony-Induced Creep Property Deterioration and Its Suppression by Rare Earth Ceriumfor a 9Cr-1Mo Ferritic Heat-Resistant Steel

Directory of Open Access Journals (Sweden)

Yewei Xu

2016-08-01

Full Text Available The high temperature creep properties of three groups of modified 9Cr-1Mo steel samples, undoped, doped with Sb, and doped with Sb and Ce, are evaluated under the applied stresses from 150 MPa to 210 MPa and at the temperatures from 873–923 K. The creep behavior follows the temperature-compensated power law as well as the Monkman-Grant relation. The creep activation energy for the Sb-doped steel (519 kJ/mol is apparently lower than that for the undoped one (541 kJ/mol, but it is considerably higher for the Sb+Ce-doped steel (621 kJ/mol. Based on the obtained relations, both the creep lifetimes under 50 MPa, 80 MPa, and 100 MPa in the range 853–923 K and the 105 h creep rupture strengths at 853 K, 873 K, and 893 K are predicted. It is demonstrated that the creep properties of the Sb-doped steel are considerably deteriorated but those of the Sb+Ce-doped steel are significantly improved as compared with the undoped steel. Microstructural and microchemical characterizations indicate that the minor addition of Ce can stabilize the microstructure of the steel by segregating to grain boundaries and dislocations, thereby offsetting the deleterious effect of Sb by coarsening the microstructure and weakening the grain boundary.

Current status and recent research achievements in ferritic/martensitic steels

Science.gov (United States)

Tavassoli, A.-A. F.; Diegele, E.; Lindau, R.; Luzginova, N.; Tanigawa, H.

2014-12-01

When the austenitic stainless steel 316L(N) was selected for ITER, it was well known that it would not be suitable for DEMO and fusion reactors due to its irradiation swelling at high doses. A parallel programme to ITER collaboration already had been put in place, under an IEA fusion materials implementing agreement for the development of a low activation ferritic/martensitic steel, known for their excellent high dose irradiation swelling resistance. After extensive screening tests on different compositions of Fe-Cr alloys, the chromium range was narrowed to 7-9% and the first RAFM was industrially produced in Japan (F82H: Fe-8%Cr-2%W-TaV). All IEA partners tested this steel and contributed to its maturity. In parallel several other RAFM steels were produced in other countries. From those experiences and also for improving neutron efficiency and corrosion resistance, European Union opted for a higher chromium lower tungsten grade, Fe-9%Cr-1%W-TaV steel (Eurofer), and in 1997 ordered the first industrial heats. Other industrial heats have been produced since and characterised in different states, including irradiated up to 80 dpa. China, India, Russia, Korea and US have also produced their grades of RAFM steels, contributing to overall maturity of these steels. This paper reviews the work done on RAFM steels by the fusion materials community over the past 30 years, in particular on the Eurofer steel and its design code qualification for RCC-MRx.

Current status and recent research achievements in ferritic/martensitic steels

Energy Technology Data Exchange (ETDEWEB)

Tavassoli, A.-A.F., E-mail: farhad.tavassoli@cea.fr [Commissariat à l' Energie Atomique et aux Energies Alternatives, CEA/DEN/DANS/DMN, F-91191 Gif-sur-Yvette (France); Diegele, E., E-mail: eberhard.diegele@kit.edu [Karlsruhe Institut of Technology (KIT), Karlsruhe (Germany); Lindau, R., E-mail: rainer.lindau@kit.edu [Karlsruhe Institut of Technology (KIT), Karlsruhe (Germany); Luzginova, N., E-mail: Natalia.Luzginova@gmail.com [NRG-Petten, 1755 ZG Petten (Netherlands); Tanigawa, H., E-mail: tanigawa.hiroyasu@jaea.go.jp [Japan Atomic Energy Authority (JAEA), Tokai, Ibaraki, 319-1195 (Japan)

2014-12-15

When the austenitic stainless steel 316L(N) was selected for ITER, it was well known that it would not be suitable for DEMO and fusion reactors due to its irradiation swelling at high doses. A parallel programme to ITER collaboration already had been put in place, under an IEA fusion materials implementing agreement for the development of a low activation ferritic/martensitic steel, known for their excellent high dose irradiation swelling resistance. After extensive screening tests on different compositions of Fe–Cr alloys, the chromium range was narrowed to 7–9% and the first RAFM was industrially produced in Japan (F82H: Fe–8%Cr–2%W–TaV). All IEA partners tested this steel and contributed to its maturity. In parallel several other RAFM steels were produced in other countries. From those experiences and also for improving neutron efficiency and corrosion resistance, European Union opted for a higher chromium lower tungsten grade, Fe–9%Cr–1%W–TaV steel (Eurofer), and in 1997 ordered the first industrial heats. Other industrial heats have been produced since and characterised in different states, including irradiated up to 80 dpa. China, India, Russia, Korea and US have also produced their grades of RAFM steels, contributing to overall maturity of these steels. This paper reviews the work done on RAFM steels by the fusion materials community over the past 30 years, in particular on the Eurofer steel and its design code qualification for RCC-MRx.

Synthesis and Characterization of Nd(3+)-Doped CaF2 Nanoparticles.

Science.gov (United States)

Yuan, Dan; Li, Weiwei; Mei, Bingchu; Song, Jinghong

2015-12-01

The Ca(1-x)F(2+x):Nd(x) nanoparticles were synthesized by chemical direct precipitation method. X-ray Diffraction (XRD), Scanning Electron Microscopy (SEM), Image analyzer, absorption spectrum and transmittance were taken to characterization the phases, morphologies, sizes, size distribution and optical properties of the samples. The results indicate that the Ca(1-x)F(2+x):Nd(x) samples can be rationally modified in size and morphology by altering the Nd3+ ions doping concentration. With increasing concentration of Nd3+ ions, the particle size decreased from 24 to 14 nm, the intensity of the diffraction peaks decreased, the Ca(1-x)F(2+x):Nd(x) particles aggregated ion of the formed clusters which should have an effect on both speed and orientation of the particles growth. The transmittance of ceramics with a thickness of 2 mm showed that the transmittance can reach 90% when the doping concentration was 5%, which should be profitable for LD pumping.

Thermally and optically stimulated radiative processes in Eu and Y co-doped LiCaAlF{sub 6} crystal

Energy Technology Data Exchange (ETDEWEB)

Fukuda, Kentaro, E-mail: ken-fukuda@tokuyama.co.jp [Tokuyama Corporation, 1-1 Mikage-cho, Shunan-shi, Yamaguchi 745-8648 (Japan); Yanagida, Takayuki; Fujimoto, Yutaka [Kyushu Institute of Technology, 2-4 Hibikino, Wakamatsu, Kitakyushu, Fukuoka 808-0196 (Japan)

2015-06-01

Yttrium co-doping was attempted to enhance dosimeter performance of Eu doped LiCaAlF{sub 6} crystal. Eu doped and Eu, Y co-doped LiCaAlF{sub 6} were prepared by the micro-pulling-down technique, and their dosimeter characteristics such as optically stimulated luminescence (OSL) and thermally stimulated luminescence (TSL) were investigated. By yttrium co-doping, emission intensities of OSL and TSL were enhanced by some orders of magnitude. In contrast, scintillation characteristics of yttrium co-doped crystal such as intensity of prompt luminescence induced by X-ray and light yield under neutron irradiation were degraded.

Fluorine and boron co-doped diamond-like carbon films deposited by pulsed glow discharge plasma immersion ion processing

CERN Document Server

He, X M; Peters, A M; Taylor, B; Nastasi, M

2002-01-01

Fluorine (F) and boron (B) co-doped diamond-like carbon (FB-DLC) films were prepared on different substrates by the plasma immersion ion processing (PIIP) technique. A pulse glow discharge plasma was used for the PIIP deposition and was produced at a pressure of 1.33 Pa from acetylene (C sub 2 H sub 2), diborane (B sub 2 H sub 6), and hexafluoroethane (C sub 2 F sub 6) gas. Films of FB-DLC were deposited with different chemical compositions by varying the flow ratios of the C sub 2 H sub 2 , B sub 2 H sub 6 , and C sub 2 F sub 6 source gases. The incorporation of B sub 2 H sub 6 and C sub 2 F sub 6 into PIIP deposited DLC resulted in the formation of F-C and B-C hybridized bonding structures. The levels of the F and B concentrations effected the chemical bonding and the physical properties as was evident from the changes observed in density, hardness, stress, friction coefficient, and contact angle of water on films. Compared to B-doped or F-doped DLC films, the F and B co-doping of DLC during PIIP deposition...

DFT study of adsorption and dissociation behavior of H2S on Fe-doped graphene

International Nuclear Information System (INIS)

Zhang, Hong-ping; Luo, Xue-gang; Song, Hong-tao; Lin, Xiao-yan; Lu, Xiong; Tang, Youhong

2014-01-01

Highlights: • Fe-doped and Pt-doped graphene can significantly improve the interactions between H 2 S and graphene. • The location of S had an important role in the interactions between H 2 S and Fe-doped graphene. • The influence of Fe-S distance can be very weak in a certain range and H 2 S can be dissociated into S and H 2 . - Abstracts: Understanding the interaction mechanisms of hydrogen sulfide (H 2 S) with graphene is important in developing graphene-based sensors for gas detection and removal. In this study, the effects of doped Fe atom on interaction of H 2 S with graphene were investigated by density functional theory calculations. Analyses of adsorption energy, electron density difference, and density of states indicated that the doped Fe atom can significantly improve the interaction of H 2 S gas molecules with graphene, as well as Pt-doped graphene. The location of the sulfur atom is important in the interactions between H 2 S and Fe-doped graphene. The influence of the Fe-S distance can be very weak within a certain distance, as simulated in this study

H2S cracking resistance of type 420 stainless steel tubulars

International Nuclear Information System (INIS)

Klein, L.J.

1984-01-01

Type 420 stainless steel (13Cr) production tubing is being used successfully in deep sour gas wells in the Tuscaloosa Trend. Despite their reputation for poor H 2 S cracking resistance in laboratory tests, 12-13% Cr steels continue to perform well in sour environments. NACE Tensile Test and Shell bent beam test results indicate Type 420 is more resistant to H 2 S cracking than Type 410, but is not as resistant as carbon steel, at to 586-690 MPa (85-100 ksi) yield strength level. In addition to evaluating Type 420 stainless steel in the standard NACE Tensile and Shell bent beam tests, the effects on cracking tendency of chloride concentration, pH, and H 2 S gas concentration in the NACE Test solution were also examined. Type 420 appears to be more resistant to H 2 S cracking than is indicated by standard laboratory tests, at least in low H 2 S level sour environments

Superior catalytic effect of TiF{sub 3} over TiCl{sub 3} in improving the hydrogen sorption kinetics of MgH{sub 2}: Catalytic role of fluorine anion

Energy Technology Data Exchange (ETDEWEB)

Ma, L.-P.; Kang, X.-D.; Dai, H.-B.; Liang, Y.; Fang, Z.-Z.; Wang, P.-J. [Shenyang National Laboratory for Materials Science, Institute of Metal Research, Chinese Academy of Sciences, Shenyang 110016 (China); Wang, P. [Shenyang National Laboratory for Materials Science, Institute of Metal Research, Chinese Academy of Sciences, Shenyang 110016 (China)], E-mail: pingwang@imr.ac.cn; Cheng, H.-M. [Shenyang National Laboratory for Materials Science, Institute of Metal Research, Chinese Academy of Sciences, Shenyang 110016 (China)

2009-04-15

TiF{sub 3} shows a superior catalytic effect over TiCl{sub 3} in improving the hydrogen sorption kinetics of MgH{sub 2}. Combined phase analysis and microstructure characterization suggest that both titanium halide additives react with host MgH{sub 2} in a similar way. However, systematic X-ray photoelectron spectroscopy studies reveal that the incorporated fluorine (F) differs significantly from its analog chlorine (Cl) in terms of bonding state. The asymmetry of F 1s spectra and the sputtering-induced peak shift suggest that, in addition to the Mg-F bond, a new Ti-F-Mg bonding is formed in the TiF{sub 3}-doped MgH{sub 2}. In contrast, only one stable binding state of Cl is identified in the form of MgCl{sub 2} for the TiCl{sub 3}-doped MgH{sub 2}. In combination with the designed experiments, these findings suggest that the generation of active F-containing species may be responsible for the advantage of TiF{sub 3} over TiCl{sub 3} in improving both the absorption and desorption kinetics of MgH{sub 2}. Fundamentally, it emphasizes the functionality of F anion in tuning the activity of compound catalyst.

Low temperature plasma carburizing of AISI 316L austenitic stainless steel and AISI F51 duplex stainless steel

OpenAIRE

Pinedo,Carlos Eduardo; Tschiptschin,André Paulo

2013-01-01

In this work an austenitic AISI 316L and a duplex AISI F51 (EN 1.4462) stainless steel were DC-Plasma carburized at 480ºC, using CH4 as carbon carrier gas. For the austenitic AISI 316L stainless steel, low temperature plasma carburizing induced a strong carbon supersaturation in the austenitic lattice and the formation of carbon expanded austenite (γC) without any precipitation of carbides. The hardness of the carburized AISI 316L steel reached a maximum of 1000 HV due to ∼13 at% c...

Low temperature plasma carburizing of AISI 316L austenitic stainless steel and AISI F51 duplex stainless steel

OpenAIRE

Pinedo, Carlos Eduardo; Tschiptschin, André Paulo

2013-01-01

In this work an austenitic AISI 316L and a duplex AISI F51 (EN 1.4462) stainless steel were DC-Plasma carburized at 480ºC, using CH4 as carbon carrier gas. For the austenitic AISI 316L stainless steel, low temperature plasma carburizing induced a strong carbon supersaturation in the austenitic lattice and the formation of carbon expanded austenite (γC) without any precipitation of carbides. The hardness of the carburized AISI 316L steel reached a maximum of 1000 HV due to ∼13 at% carbon super...

Optical characterization of Tm3+ doped Bi2O3-GeO2-Ga2O3 glasses in absence and presence of BaF2

Science.gov (United States)

Han, Kexuan; Zhang, Peng; Wang, Shunbin; Guo, Yanyan; Zhou, Dechun; Yu, Fengxia

2016-01-01

In this paper, Two new Bi2O3-GeO2-Ga2O3 glasses (one presence of BaF2) doped with 1mol% Tm2O3 were prepared by melt-quenching technique. Differential thermal analysis (DTA), the absorption, Raman, IR spectra and fluorescence spectra were measured. The Judd–Ofelt intensity parameters, emission cross section, absorption cross section, and gain coefficient of Tm3+ ions were comparatively investigated. After the BaF2 introduced, the glass showed a better thermal stability, lower phonon energy and weaker OH− absorption coefficient, meanwhile, a larger ~1.8 μm emission cross section σem (7.56 × 10−21 cm2) and a longer fluorescence lifetime τmea (2.25 ms) corresponding to the Tm3+: 4F3 → 3H6 transition were obtained, which is due to the addition of fluoride in glass could reduce the quenching rate of hydroxyls and raise the cross-relaxation (3H6 + 3H4 → 3F4 + 3F4) rate. Our results suggest that the Tm3+ doped Bi2O3-GeO2-Ga2O3 glass with BaF2 might be potential to the application in efficient ~1.8 μm lasers system. PMID:27506152

Optical characterization of Tm(3+) doped Bi2O3-GeO2-Ga2O3 glasses in absence and presence of BaF2.

Science.gov (United States)

Han, Kexuan; Zhang, Peng; Wang, Shunbin; Guo, Yanyan; Zhou, Dechun; Yu, Fengxia

2016-08-10

In this paper, Two new Bi2O3-GeO2-Ga2O3 glasses (one presence of BaF2) doped with 1mol% Tm2O3 were prepared by melt-quenching technique. Differential thermal analysis (DTA), the absorption, Raman, IR spectra and fluorescence spectra were measured. The Judd-Ofelt intensity parameters, emission cross section, absorption cross section, and gain coefficient of Tm(3+) ions were comparatively investigated. After the BaF2 introduced, the glass showed a better thermal stability, lower phonon energy and weaker OH(-) absorption coefficient, meanwhile, a larger ~1.8 μm emission cross section σem (7.56 × 10(-21) cm(2)) and a longer fluorescence lifetime τmea (2.25 ms) corresponding to the Tm(3+): (4)F3 → (3)H6 transition were obtained, which is due to the addition of fluoride in glass could reduce the quenching rate of hydroxyls and raise the cross-relaxation ((3)H6 + (3)H4 → (3)F4 + (3)F4) rate. Our results suggest that the Tm(3+) doped Bi2O3-GeO2-Ga2O3 glass with BaF2 might be potential to the application in efficient ~1.8 μm lasers system.

Improved hydrogen storage properties of LiAlH4 by mechanical milling with TiF3

International Nuclear Information System (INIS)

Zang, Lei; Cai, Jiaxing; Zhao, Lipeng; Gao, Wenhong; Liu, Jian; Wang, Yijing

2015-01-01

Dehydrogenation behavior of LiAlH 4 (lithium alanate) admixed with TiF 3 is investigated by pressure-composition-temperature (PCT), fourier transform infrared spectroscopy (FTIR), X-ray Diffraction (XRD), differential scanning calorimetry (DSC) and temperature programmed desorption (TPD). The TiF 3 addition enhances kinetics of LiAlH 4 and decreases the decomposition temperature. The LiAlH 4 -2 mol % TiF 3 sample starts to release hydrogen at about 35 °C and the dehydrogenation rate reaches a maximum value at 108.4 °C, compared with 145 °C and 179.9 °C for the as-received LiAlH 4 . As for the dehydrogenation kinetics, the LiAlH 4 -2 mol % TiF 3 sample releases about 7.0 wt % H 2 at 140 °C within 80 min. In comparison, the as-received LiAlH 4 sample releases only 0.8 wt % hydrogen under the same conditions. The existence of proposed catalyst, Al 3 Ti formed in-situ in the process of dehydrogenation, has been confirmed experimentally by XRD measurements. The activation energy of LiAlH 4 -2 mol % TiF 3 composite is deduced to be 66.76 kJ mol −1 and 88.21 kJ mol −1 for the first and second reaction stages of LiAlH 4 dehydrogenation. - Highlights: • TiF 3 considerably enhances the dehydrogenation kinetics of LiAlH 4 . • TiF 3 -doped LiAlH 4 dehydrogenates even at room temperature. • Low activation energy of the dehydrogenation reaction. • Al 3 Ti formed in-situ helps to explain the dehydrogenation mechanism

Controllable synthesis and upconversion emission of ultrasmall near-monodisperse lanthanide-doped Sr2LaF7 nanocrystals

International Nuclear Information System (INIS)

Mao, Yifu; Ma, Mo; Gong, Lunjun; Xu, Changfu; Ren, Guozhong; Yang, Qibin

2014-01-01

Highlights: • Apropos NaOH content facilitates the growth of pure phase Sr 2 LaF 7 NCs. • Yb 3+ doping is favorable to the formation of Sr 2 LaF 7 NCs with uniform size. • Ultrasmall near-monodispersed Sr 2 LaF 7 NCs(sub-10 nm) were synthesized for the first time. • Intense multicolor upconversion can be obtained by properly lanthanide doping. - Abstract: Fluorite phase Sr 2 LaF 7 nanocrystals (NCs) were synthesized via solvothermal method using oleic acid as capping ligands. The effects of preparing conditions on the phase structure, crystal size, morphology, and upconversion (UC) emission properties of the products were studied. The results reveal that just apropos NaOH content facilitates the growth of near-monodispersed pure phase Sr 2 LaF 7 NCs, and Yb 3+ doping is favorable to the formation of pure Sr 2 LaF 7 phase with more uniform size distribution. The average crystalline size of the products can be controlled less than 10 nm. Following appropriate lanthanide ions doping, the NCs show intense blue, yellow, and white-color UC emission under the excitation of a 980 nm laser. The energy transfer UC mechanisms for the fluorescent intensity were also investigated

Controllable synthesis and crystal structure determined upconversion luminescence properties of Tm{sup 3+} (Er{sup 3+}) ions doped YbF{sub 3} and NaYbF{sub 4} crystals

Energy Technology Data Exchange (ETDEWEB)

Jiang, Tao [Institute of Photonics, Faculty of Science, Ningbo University, Ningbo 315211 (China); Qin, Weiping, E-mail: wpqin@jlu.edu.cn [State Key Laboratory on Integrated Optoelectronics, College of Electronic Science and Engineering, Jilin University, Changchun 130012 (China); Zhou, Jun [Institute of Photonics, Faculty of Science, Ningbo University, Ningbo 315211 (China)

2014-04-01

Graphical abstract: - Highlights: • The synthesis of YbF{sub 3} and NaYbF{sub 4} crystals was successfully fulfilled by hydrothermal method. • The phase and morphology of products were adjusted by changing the hydrothermal conditions. • Relatively enhanced ultraviolet upconversion emissions were observed in YbF{sub 3} nanocrystals. • The crystalline phase impact on the upconversion luminescence was systematically studied. - Abstract: The synthesis of YbF{sub 3} and NaYbF{sub 4} crystals was successfully fulfilled by a facial hydrothermal method. The phase and morphology of the products were adjusted by changing the surfactant additive and fluorine source and tuning the pH value of the initial solution. The products with various morphologies range from octahedral nanoparticles, corn-like nanobundles, nanospheres, microrods, and hollow microprisms were prepared at different conditions. The growth mechanism of these products has been systematically studied. Impressively, relatively enhanced high order ultraviolet (UV) upconversion (UC) luminescence was observed in Tm{sup 3+} (Er{sup 3+}) ions doped YbF{sub 3} nanocrystals (NCs) compared with NaYbF{sub 4} microcrystals under the excitation of 980 nm infrared laser. The investigation results reveal that the crystal symmetry of matrix has significant effect on the spectra and lifetimes of the doping lanthanide ions. The simply synthesized water soluble YbF{sub 3} NCs with efficient UV UC luminescence may find potential application in biochemistry.

Some mechanical properties of borided AISI H13 and 304 steels

International Nuclear Information System (INIS)

Taktak, Sukru

2007-01-01

In the present study, mechanical properties of borides formed on AISI H13 hot work tool and AISI 304 stainless steels have been investigated. Both steels have high chromium content and have a widespread use in the engineering application. Boriding treatment was carried out in slurry salt bath consisting of borax, boric acid, and ferrosilicon at temperature range of 800-950 deg. C for 3, 5, and 7 h. X-ray diffraction analysis of boride layers on the surface of steels revealed various peaks of FeB, Fe 2 B, CrB, and Ni 3 B. Metallographic studies showed that the boride layer has a flat and smooth morphology in the 304 steel while H13 steel was a ragged morphology. The characterization of the boride layer is also carried out by means of the micro-hardness, surface roughness, adhesion, and fracture toughness studies

Sorption properties and reversibility of Ti(IV) and Nb(V)-fluoride doped-Ca(BH{sub 4}){sub 2}-MgH{sub 2} system

Energy Technology Data Exchange (ETDEWEB)

Bonatto Minella, Christian, E-mail: christian.minella@kit.edu [Institute for Metallic Materials, IFW Dresden, Helmholtzstrasse 20, D-01069 Dresden (Germany); Technische Universität Dresden, D-01062 Dresden (Germany); Garroni, Sebastiano [Dipartimento di Chimica e Farmacia, Universitá di Sassari and INSTM, Via Vienna 2, I-07100 Sassari (Italy); Pistidda, Claudio [Institute of Materials Research, Materials Technology, Helmholtz-Zentrum Geesthacht, Zentrum für Material- und Küstenforschung GmbH, Max Planck Str. 1, D-21502 Geesthacht (Germany); Baró, Maria Dolors [Departament de Física, Universitat Autònoma de Barcelona, E-08193 Bellaterra (Spain); Gutfleisch, Oliver [Materials Science, Technische Universität Darmstadt, Alarich-Weiss-Str. 16, 64287 Darmstadt (Germany); Klassen, Thomas; Dornheim, Martin [Institute of Materials Research, Materials Technology, Helmholtz-Zentrum Geesthacht, Zentrum für Material- und Küstenforschung GmbH, Max Planck Str. 1, D-21502 Geesthacht (Germany)

2015-02-15

Highlights: • Faster desorption reaction for doped materials vs. the pure composite system. • Kinetic improvement concerning re-hydrogenation reaction showed by the addition of NbF{sub 5}. • Full characterization of the de-hydrogenation reaction pathway by means of both SR-PXD and {sup 11}B{"1H} MAS-NMR. • Study of the evolution of the chemical state of the additives upon both milling and sorption reactions. - Abstract: In the last decade, alkaline and alkaline earth metal tetrahydroborates have been the focuses of the research due to their high gravimetric and volumetric hydrogen densities. Among them, Ca(BH{sub 4}){sub 2} and the Ca(BH{sub 4}){sub 2} + MgH{sub 2} reactive hydride composites (RHC), were calculated to have the ideal thermodynamic properties which fall within the optimal range for mobile applications. In this study, the addition of NbF{sub 5} or TiF{sub 4} to the Ca(BH{sub 4}){sub 2} + MgH{sub 2} reactive hydride composite system was attempted aiming to obtain a full reversible system with the simultaneous suppression of CaB{sub 12}H{sub 12}. Structural characterization of the specimens was performed by means of in-situ Synchrotron Radiation Powder X-ray diffraction (SR-PXD) and {sup 11}B{"1H} Solid State Magic Angle Spinning-Nuclear Magnetic Resonance (MAS-NMR). The evolution of the chemical state of the Nb- and Ti-based additives was monitored by X-ray Absorption Near Edge Structure (XANES). The addition of NbF{sub 5} or TiF{sub 4} to the Ca(BH{sub 4}){sub 2} + MgH{sub 2} system have not suppressed completely the formation of CaB{sub 12}H{sub 12} and only a slight improvement concerning the reversible reaction was displayed just in the case of Nb-doped composite material.

Grazing incidence synchrotron X-ray diffraction and Moessbauer spectroscopy analyses of plasma nitrided ASTM F138 stainless steel

Energy Technology Data Exchange (ETDEWEB)

Souza, Danilo Olzon Dionysio de; Ardisson, Jose Domingos, E-mail: dolzon@gmail.com [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN-MG), Belo Horizonte, MG (Brazil); Silva, Edilaine Honorio [Studiecentrum voor Kernenergie (Belgium); Olzon-Dionysio, Maristela; Souza, Sylvio Dionysio de; Fabris, Jose Domingos [Universidade Federal dos Vales do Jequitinhonha e Mucuri (UFVJM), Diamantina, MG (Brazil); Martinez, L.G. [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

2016-07-01

Full text: systematic investigation of samples of plasma-nitriding austenitic stainless steels ASTM F138 and AISI 316L is reported. The surface treatment of the steels through plasma-nitriding was used to improve further the hardness, wear and corrosion resistance of these stainless steels. The resulting layered crystallographic structure actually corresponds to several phases with close cell parameters, making their identification and quantification a real experimental challenge. The ASTM F138 and AISI 316L stainless steel disks were plasma nitrided for 4 h at 400 deg C in a 80% H{sub 2} -20% N2 atmosphere at 6 torr, using plasma current frequencies between 6 and 100 kHz. Data of Moessbauer (CEMS and CXMS) and grazing incidence synchrotron X-ray diffraction (XRD-SR) were systematically collected. The nitrided layer thickness were not in general influenced by the plasma frequency, except at 12 kHz, which produced a layer thickness of approximately 8.0 mm, being in average 40% thicker than for the other samples. CXMS and CEMS Moessbauer spectra for this 12 kHz-sample show a much more pronounced magnetic resonance lines than for the other samples. The Fe{sub 4}N phase presents a single magnetic hyperfine interaction; the other two (Fe{sub 2-3}N and the expanded austenite) present both paramagnetic and magnetic components, even though their hyperfine parameters may not be safely separated. We also present the results of XRD-SR that were probed at several depths. The data from these techniques may be consistently correlated and this leads to an improved model to explain the structure of the nitrided layers. (author)

Studies on Stress Corrosion Cracking of Super 304H Austenitic Stainless Steel

Science.gov (United States)

Prabha, B.; Sundaramoorthy, P.; Suresh, S.; Manimozhi, S.; Ravishankar, B.

2009-12-01

Stress corrosion cracking (SCC) is a common mode of failure encountered in boiler components especially in austenitic stainless steel tubes at high temperature and in chloride-rich water environment. Recently, a new type of austenitic stainless steels called Super304H stainless steel, containing 3% copper is being adopted for super critical boiler applications. The SCC behavior of this Super 304H stainless steel has not been widely reported in the literature. Many researchers have studied the SCC behavior of steels as per various standards. Among them, the ASTM standard G36 has been widely used for evaluation of SCC behavior of stainless steels. In this present work, the SCC behavior of austenitic Fe-Cr-Mn-Cu-N stainless steel, subjected to chloride environments at varying strain conditions as per ASTM standard G36 has been studied. The environments employed boiling solution of 45 wt.% of MgCl2 at 155 °C, for various strain conditions. The study reveals that the crack width increases with increase in strain level in Super 304H stainless steels.

Inhibition of VEGF-dependent angiogenesis by the anti-CD82 monoclonal antibody 4F9 through regulation of lipid raft microdomains

International Nuclear Information System (INIS)

Nomura, Sayaka; Iwata, Satoshi; Hatano, Ryo; Komiya, Eriko; Dang, Nam H.; Iwao, Noriaki; Ohnuma, Kei; Morimoto, Chikao

2016-01-01

CD82 (also known as KAI1) belongs to the tetraspanin superfamily of type III transmembrane proteins, and is involved in regulating cell adhesion, migration and proliferation. In contrast to these well-established roles of CD82 in tumor biology, its function in endothelial cell (EC) activity and tumor angiogenesis is yet to be determined. In this study, we show that suppression of CD82 negatively regulates vascular endothelial growth factor (VEGF)-induced angiogenesis. Moreover, we demonstrate that the anti-CD82 mAb 4F9 effectively inhibits phosphorylation of VEGF receptor 2 (VEGFR2), which is the principal mediator of the VEGF-induced angiogenic signaling process in tumor angiogenesis, by regulating the organization of the lipid raft microdomain signaling platform in human EC. Our present work therefore suggests that CD82 on EC is a potential target for anti-angiogenic therapy in VEGFR2-dependent tumor angiogenesis. -- Highlights: •Knockdown of CD82 decreases EC migration, proliferation and angiogenesis. •Anti-CD82 mAb 4F9 inhibits EC migration, proliferation and angiogenesis. •4F9 inhibits VEGFR2 phosphorylation via control of CD82 distribution in lipid rafts.

Inhibition of VEGF-dependent angiogenesis by the anti-CD82 monoclonal antibody 4F9 through regulation of lipid raft microdomains

Energy Technology Data Exchange (ETDEWEB)

Nomura, Sayaka; Iwata, Satoshi; Hatano, Ryo [Division of Clinical Immunology, Advanced Clinical Research Center, The Institute of Medical Science, The University of Tokyo, 4-6-1 Shirokanedai, Minato-ku, Tokyo, 108-8639 (Japan); Komiya, Eriko [Department of Therapy Development and Innovation for Immune Disorders and Cancers, Graduate School of Medicine, Juntendo University, 2-1-1, Hongo, Bunkyo-ku, Tokyo, 113-8421 (Japan); Dang, Nam H. [Division of Hematology/Oncology, University of Florida, 1600 SW Archer Road- Box 100278, Room MSB M410A, Gainesville, FL, 32610 (United States); Iwao, Noriaki [Department of Hematology, School of Medicine, Juntendo University, 2-1-1, Hongo, Bunkyo-ku, Tokyo, 113-8421 (Japan); Ohnuma, Kei, E-mail: kohnuma@juntendo.ac.jp [Department of Rheumatology and Allergy, IMSUT Hospital, The Institute of Medical Science, The University of Tokyo, 4-6-1 Shirokanedai, Minato-ku, Tokyo, 108-8639 (Japan); Morimoto, Chikao [Division of Clinical Immunology, Advanced Clinical Research Center, The Institute of Medical Science, The University of Tokyo, 4-6-1 Shirokanedai, Minato-ku, Tokyo, 108-8639 (Japan); Department of Rheumatology and Allergy, IMSUT Hospital, The Institute of Medical Science, The University of Tokyo, 4-6-1 Shirokanedai, Minato-ku, Tokyo, 108-8639 (Japan)

2016-05-20

CD82 (also known as KAI1) belongs to the tetraspanin superfamily of type III transmembrane proteins, and is involved in regulating cell adhesion, migration and proliferation. In contrast to these well-established roles of CD82 in tumor biology, its function in endothelial cell (EC) activity and tumor angiogenesis is yet to be determined. In this study, we show that suppression of CD82 negatively regulates vascular endothelial growth factor (VEGF)-induced angiogenesis. Moreover, we demonstrate that the anti-CD82 mAb 4F9 effectively inhibits phosphorylation of VEGF receptor 2 (VEGFR2), which is the principal mediator of the VEGF-induced angiogenic signaling process in tumor angiogenesis, by regulating the organization of the lipid raft microdomain signaling platform in human EC. Our present work therefore suggests that CD82 on EC is a potential target for anti-angiogenic therapy in VEGFR2-dependent tumor angiogenesis. -- Highlights: •Knockdown of CD82 decreases EC migration, proliferation and angiogenesis. •Anti-CD82 mAb 4F9 inhibits EC migration, proliferation and angiogenesis. •4F9 inhibits VEGFR2 phosphorylation via control of CD82 distribution in lipid rafts.

Transmission photocathodes based on stainless steel mesh and quartz glass coated with N-doped DLC thin films prepared by reactive magnetron sputtering

Science.gov (United States)

Balalykin, N. I.; Huran, J.; Nozdrin, M. A.; Feshchenko, A. A.; Kobzev, A. P.; Arbet, J.

2016-03-01

The influence was investigated of N-doped diamond-like carbon (DLC) films properties on the quantum efficiency of a prepared transmission photocathode. N-doped DLC thin films were deposited on a silicon substrate, a stainless steel mesh and quartz glass (coated with 5 nm thick Cr adhesion film) by reactive magnetron sputtering using a carbon target and gas mixture Ar, 90%N2+10%H2. The elements' concentration in the films was determined by RBS and ERD. The quantum efficiency was calculated from the measured laser energy and the measured cathode charge. For the study of the vectorial photoelectric effect, the quartz type photocathode was irradiated by intensive laser pulses to form pin-holes in the DLC film. The quantum efficiency (QE), calculated at a laser energy of 0.4 mJ, rose as the nitrogen concentration in the DLC films was increased and rose dramatically after the micron-size perforation in the quartz type photocathodes.

Corrosion of type 316 stainless steel in molten LiF-LiCl-LiBr

International Nuclear Information System (INIS)

Tortorelli, P.F.; DeVan, J.H.; Keiser, J.R.

1981-01-01

The properties of LiF-LiCl-LiBr salt make it attractive as a solvent for extracting tritium from a fusion reactor lithium blanket. Consequently, the corrosion of type 316 stainless steel by flowing (about 15 mm/s) LiF-LiCl-LiBr at a maximum temperature of 535 0 C was studied to determine whether compatibility with the structural material would be limiting in such a system. The corrosion rate was found to be low ( 0 C (approximately that of type 316 stainless steel exposed to lithium flowing at a similar velocity). At the proposed operating temperature (less than or equal to approx. 535 0 C), however, it appears that type 316 stainless steel has acceptable compatibility with the tritium-processing salt LiF-LiCl-LiBr for use with a lithium blanket

Electroplating of erbium on steel surface in ErCl3 doped LiCl-KCl

International Nuclear Information System (INIS)

Kondo, Masatoshi; Tanaka, Teruya; Muroga, Takeo; Tsujimura, Hiroyuki; Ito, Yasuhiko

2012-01-01

The electroplating of Er metal on the reduced activation ferritic martensitic steel, JLF-1 (Fe-9Cr-2W-0.1C), in a molten salt was studied. The specimen was immersed in the molten ErCl 3 doped LiCl-KCl electrolyte. The electroplating was carried out by a constant potential electrolysis method and a pulsed current electrolysis method. It was found that the Er metal was deposited on the specimen surface due to the electrochemical reaction. (author)

Molecular Doping the Topological Dirac Semimetal Na3Bi across the Charge Neutrality Point with F4-TCNQ.

Science.gov (United States)

Edmonds, Mark T; Hellerstedt, Jack; O'Donnell, Kane M; Tadich, Anton; Fuhrer, Michael S

2016-06-29

We perform low-temperature transport and high-resolution photoelectron spectroscopy on 20 nm thin film topological Dirac semimetal Na3Bi grown by molecular beam epitaxy. We demonstrate efficient electron depletion ∼10(13) cm(-2) of Na3Bi via vacuum deposition of molecular F4-TCNQ without degrading the sample mobility. For samples with low as-grown n-type doping (1 × 10(12) cm(-2)), F4-TCNQ doping can achieve charge neutrality and even a net p-type doping. Photoelectron spectroscopy and density functional theory are utilized to investigate the behavior of F4-TCNQ on the Na3Bi surface.

H{sub 2}-Ar dilution for improved c-Si quantum dots in P-doped SiN{sub x}:H thin film matrix

Energy Technology Data Exchange (ETDEWEB)

Liu, Jia [Shaanxi Engineering Lab for Advanced Energy Technology, School of Materials Science and Engineering, Shaanxi Normal University, Xi’an 710119 (China); Zhang, Weijia, E-mail: zwjghx@126.com [Center of Condensed Matter and Material Physics, School of Physics and Nuclear Energy Engineering, Beihang University, Beijing, 100191 (China); Liu, Shengzhong, E-mail: szliu@dicp.ac.cn [Shaanxi Engineering Lab for Advanced Energy Technology, School of Materials Science and Engineering, Shaanxi Normal University, Xi’an 710119 (China); State key Laboratory of Catalysis, iChEM, Dalian Institute of Chemical Physics, Dalian National Laboratory for Clean Energy, Chinese Academy of Sciences, Dalian 116023 (China)

2017-02-28

Highlights: • Phosphorous-doped SiN{sub x}:H thin films containing c-Si QDs were prepared by PECVD in H{sub 2}-Ar mixed dilution under low temperature. • QD density and QD size can be controlled by tuning H{sub 2}/Ar flow ratio. • The sample prepared at the H{sub 2}/Ar flow ratio of 100/100 possesses both wide band gap and excellent conductivity. • Detail discussion has been presented for illustrating the influence of H{sub 2}/Ar mixed dilution on the crystallization process and P-doping. - Abstract: Phosphorus-doped hydrogenated silicon nitride (SiN{sub x}:H) thin films containing crystalline silicon quantum dot (c-Si QD) was prepared by plasma enhanced chemical vapor deposition (PECVD) using hydrogen-argon mixed dilution. The effects of H{sub 2}/Ar flow ratio on the structural, electrical and optical characteristics of as-grown P-doped SiN{sub x}:H thin films were systematically investigated. Experimental results show that crystallization is promoted by increasing the H{sub 2}/Ar flow ratio in dilution, while the N/Si atomic ratio is higher for thin film deposited with argon-rich dilution. As the H{sub 2}/Ar flow ratio varies from 100/100 to 200/0, the samples exhibit excellent conductivity owing to the large volume fraction of c-Si QDs and effective P-doping. By adjusting the H{sub 2}/Ar ratio to 100/100, P-doped SiN{sub x}:H thin film containing tiny and densely distributed c-Si QDs can be obtained. It simultaneously possesses wide optical band gap and high dark conductivity. Finally, detailed discussion has been made to analyze the influence of H{sub 2}-Ar mixed dilution on the properties of P-doped SiN{sub x}:H thin films.

Enhanced oxidation resistance of carbon fiber reinforced lithium aluminosilicate composites by boron doping

International Nuclear Information System (INIS)

Xia, Long; Jin, Feng; Zhang, Tao; Hu, Xueting; Wu, Songsong; Wen, Guangwu

2015-01-01

Highlights: • C f /LAS composites exhibit enhanced oxidation resistance by boron doping. • Boron doping is beneficial to the improvement of graphitization degree of carbon fibers. • Graphitization of carbon fibers together with the decrease of viscosity of LAS matrix is responsible to the enhancement of oxidation resistance of C f /LAS composites. - Abstract: Carbon fiber reinforced lithium aluminosilicate matrix composites (C f /LAS) modified with boron doping were fabricated and oxidized for 1 h in static air. Weight loss, residual strength and microstructure were analyzed. The results indicate that boron doping has a remarkable effect on improving the oxidation resistance for C f /LAS. The synergism of low viscosity of LAS matrix at high temperature and formation of graphite crystals on the surface of carbon fibers, is responsible for excellent oxidation resistance of the boron doped C f /LAS.

Evaluation of local deformation behavior accompanying fatigue damage in F82H welded joint specimens by using digital image correlation

International Nuclear Information System (INIS)

Nakata, Toshiya; Tanigawa, Hiroyasu

2012-01-01

Highlights: ► In tensile, the TIG welded joint material was concentrated in the THAZ. ► In tensile, fracture occurred at the point where the axial strain converged. ► In fatigue, fracture occurred at the point where the Max. shear strain converged. ► Many macrocracks and cavities formed in the FGHAZ and THAZ of the cross section. - Abstract: By using digital image correlation, the deformation behaviors of local domains of F82H joint specimens welded using tungsten inert gas (TIG) and electron beam (EB) welding were evaluated during tensile and fatigue testing. In the tensile test specimens, the tensile strength decreased in the TIG-welded joints, and ductility decreased in both the EB- and TIG-welded joints. Because axial strain increased in the tempered heat-affected zone (HAZ) and led to the fracture of the TIG-welded joint, the strength was considered to have decreased because of welding. In fatigue testing, the number of cycles to fracture for the welded joint decreased to less than 40–60% of that for the base metal. For both fracture specimens, the largest value of shear strain was observed in the region approximately between the fine-grained HAZ and tempered HAZ; this shear strain ultimately led to fracture. Cavities and macrocracks were observed in the fine-grained HAZ and tempered HAZ in the cross sections of the fracture specimens, and geometrical damage possibly resulted in the reduction of fatigue lifetime.

A facile method to synthesize nitrogen and fluorine co-doped TiO2 nanoparticles by pyrolysis of (NH4)2TiF6

International Nuclear Information System (INIS)

Chen Daimei; Jiang Zhongyi; Geng Jiaqing; Zhu Juhong; Yang Dong

2009-01-01

The nitrogen and fluorine co-doped TiO 2 (N-F-TiO 2 ) nanoparticles of anatase crystalline structure were prepared by a facile method of (NH 4 ) 2 TiF 6 pyrolysis, and characterized by thermogravimetry-differential thermal analysis (TG-DTA), X-ray diffraction (XRD), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), and ultraviolet visible (UV-Vis) spectroscopy etc. With the increase of calcination temperature, (NH 4 ) 2 TiF 6 decomposed into TiOF 2 and NH 4 TiOF 3 at first, and then formed anatase-type TiO 2 with thin sheet morphology. H 3 BO 3 as oxygen source can promote the formation of anatase TiO 2 , but decrease the F content in the N-F-TiO 2 materials due to the formation of volatile BF 3 during the precursor decomposition. The photocatalytic activity of the obtained N-F-TiO 2 samples was evaluated by the methylene blue degradation under visible light, and all the samples exhibited much higher photocatalytic activity than P25. Moreover, the merits and disadvantages of this proposed method to prepare doped TiO 2 are discussed.

Variable RF capacitor based on a-Si:H (P-doped) multi-length cantilevers

International Nuclear Information System (INIS)

Fu, Y Q; Milne, S B; Luo, J K; Flewitt, A J; Wang, L; Miao, J M; Milne, W I

2006-01-01

A variable RF capacitor with a-Si:H (doped with phosphine) cantilevers as the top electrode were designed and fabricated. Because the top multi-cantilever electrodes have different lengths, increasing the applied voltage pulled down the cantilever beams sequentially, thus realizing a gradual increase of the capacitance with the applied voltage. A high-k material, H f O 2 , was used as an insulating layer to increase the tuning range of the capacitance. The measured capacitance from the fabricated capacitor was much lower and the pull-in voltage was much higher than those from theoretical analysis because of incomplete contact of the two electrodes, existence of film differential stresses and charge injection effect. Increase of sweeping voltage rate could significantly shift the pull-in voltage to higher values due to the charge injection mechanisms

H I Kinematics along the Minor Axis of M82

Science.gov (United States)

Martini, Paul; Leroy, Adam K.; Mangum, Jeffrey G.; Bolatto, Alberto; Keating, Katie M.; Sandstrom, Karin; Walter, Fabian

2018-03-01

M82 is one of the best-studied starburst galaxies in the local universe, and is consequently a benchmark for studying star formation feedback at both low and high redshift. We present new VLA H I observations that reveal the cold gas kinematics along the minor axis in unprecedented detail. This includes the detection of H I up to 10 kpc along the minor axis toward the south and beyond 5 kpc to the north. A surprising aspect of these observations is that the line-of-sight H I velocity decreases substantially from about 120 to 50 {km} {{{s}}}-1 from 1.5 to 10 kpc off the midplane. The velocity profile is not consistent with the H I gas cooling from the hot wind. We demonstrate that the velocity decrease is substantially greater than the deceleration expected from gravitational forces alone. If the H I consists of a continuous population of cold clouds, some additional drag force must be present, and the magnitude of the drag force places a joint constraint on the ratio of the ambient medium to the typical cloud size and density. We also show that the H I kinematics are inconsistent with a simple conical outflow centered on the nucleus, but instead require the more widespread launch of the H I over the ∼1 kpc extent of the starburst region. Regardless of the launch mechanism for the H I gas, the observed velocity decrease along the minor axis is sufficiently great that the H I may not escape the halo of M82. The inferred H I outflow rate at 10 kpc off the midplane is much less than 1 {M}ȯ yr‑1.

Highly concentrated, stable nitrogen-doped graphene for supercapacitors: Simultaneous doping and reduction

Energy Technology Data Exchange (ETDEWEB)

Jiang Baojiang [College of Materials Science and Chemical Engineering, Harbin Engineering University, Harbin (China); Key Laboratory of Functional Inorganic Material Chemistry, Ministry of Education of the People' s Republic of China, Heilongjiang University, Harbin (China); Tian Chungui; Wang Lei; Sun Li; Chen Chen; Nong Xiaozhen [Key Laboratory of Functional Inorganic Material Chemistry, Ministry of Education of the People' s Republic of China, Heilongjiang University, Harbin (China); Qiao Yingjie, E-mail: qiaoyingjie@hrbeu.edu.cn [College of Materials Science and Chemical Engineering, Harbin Engineering University, Harbin (China); Fu Honggang, E-mail: fuhg@vip.sina.com [Key Laboratory of Functional Inorganic Material Chemistry, Ministry of Education of the People' s Republic of China, Heilongjiang University, Harbin (China)

2012-02-01

In this work, we developed a concentrated ammonia-assisted hydrothermal method to obtain N-doped graphene sheets by simultaneous N-doping and reduction of graphene oxide (GO) sheets. The effects of hydrothermal temperature on the surface chemistry and the structure of N-doped graphene sheets were also investigated. X-ray photoelectron spectroscopy (XPS) study of N-doped graphene reveals that the highest doping level of 7.2% N is achieved at 180 Degree-Sign C for 12 h. N binding configurations of sample consist of pyridine N, quaternary N, and pyridine-N oxides. N doping is accompanied by the reduction of GO with decreases in oxygen levels from 34.8% in GO down to 8.5% in that of N-doped graphene. Meanwhile, the sample exhibits excellent N-doped thermal stability. Electrical measurements demonstrate that products have higher capacitive performance than that of pure graphene, the maximum specific capacitance of 144.6 F/g can be obtained which ascribe the pseudocapacitive effect from the N-doping. The samples also show excellent long-term cycle stability of capacitive performance.

Highly concentrated, stable nitrogen-doped graphene for supercapacitors: Simultaneous doping and reduction

Science.gov (United States)

Jiang, Baojiang; Tian, Chungui; Wang, Lei; Sun, Li; Chen, Chen; Nong, Xiaozhen; Qiao, Yingjie; Fu, Honggang

2012-02-01

In this work, we developed a concentrated ammonia-assisted hydrothermal method to obtain N-doped graphene sheets by simultaneous N-doping and reduction of graphene oxide (GO) sheets. The effects of hydrothermal temperature on the surface chemistry and the structure of N-doped graphene sheets were also investigated. X-ray photoelectron spectroscopy (XPS) study of N-doped graphene reveals that the highest doping level of 7.2% N is achieved at 180 °C for 12 h. N binding configurations of sample consist of pyridine N, quaternary N, and pyridine-N oxides. N doping is accompanied by the reduction of GO with decreases in oxygen levels from 34.8% in GO down to 8.5% in that of N-doped graphene. Meanwhile, the sample exhibits excellent N-doped thermal stability. Electrical measurements demonstrate that products have higher capacitive performance than that of pure graphene, the maximum specific capacitance of 144.6 F/g can be obtained which ascribe the pseudocapacitive effect from the N-doping. The samples also show excellent long-term cycle stability of capacitive performance.

Effects of the F4TCNQ-Doped Pentacene Interlayers on Performance Improvement of Top-Contact Pentacene-Based Organic Thin-Film Transistors

Directory of Open Access Journals (Sweden)

Ching-Lin Fan

2016-01-01

Full Text Available In this paper, the top-contact (TC pentacene-based organic thin-film transistor (OTFT with a tetrafluorotetracyanoquinodimethane (F4TCNQ-doped pentacene interlayer between the source/drain electrodes and the pentacene channel layer were fabricated using the co-evaporation method. Compared with a pentacene-based OTFT without an interlayer, OTFTs with an F4TCNQ:pentacene ratio of 1:1 showed considerably improved electrical characteristics. In addition, the dependence of the OTFT performance on the thickness of the F4TCNQ-doped pentacene interlayer is weaker than that on a Teflon interlayer. Therefore, a molecular doping-type F4TCNQ-doped pentacene interlayer is a suitable carrier injection layer that can improve the TC-OTFT performance and facilitate obtaining a stable process window.

Effects of the F4TCNQ-Doped Pentacene Interlayers on Performance Improvement of Top-Contact Pentacene-Based Organic Thin-Film Transistors

Science.gov (United States)

Fan, Ching-Lin; Lin, Wei-Chun; Chang, Hsiang-Sheng; Lin, Yu-Zuo; Huang, Bohr-Ran

2016-01-01

In this paper, the top-contact (TC) pentacene-based organic thin-film transistor (OTFT) with a tetrafluorotetracyanoquinodimethane (F4TCNQ)-doped pentacene interlayer between the source/drain electrodes and the pentacene channel layer were fabricated using the co-evaporation method. Compared with a pentacene-based OTFT without an interlayer, OTFTs with an F4TCNQ:pentacene ratio of 1:1 showed considerably improved electrical characteristics. In addition, the dependence of the OTFT performance on the thickness of the F4TCNQ-doped pentacene interlayer is weaker than that on a Teflon interlayer. Therefore, a molecular doping-type F4TCNQ-doped pentacene interlayer is a suitable carrier injection layer that can improve the TC-OTFT performance and facilitate obtaining a stable process window. PMID:28787845

Synthesis and characterization of nano- and microcrystalline cubes of pure and Ag-doped LiF

Science.gov (United States)

Alharbi, Najlaa D.; Salah, Numan; Habib, Sami S.; Alarfaj, Esam

2013-01-01

Lithium fluoride (LiF) produced in single crystals and doped with proper activators is a highly sensitive phosphor used in several applications such as integrated optics, colour centre laser and radiation dosimetry. In this work, we have developed a new synthetic chemical co-precipitation route for the synthesis of well-crystallized micro- and nanocrystalline cubes of pure and silver (Ag)-doped LiF. The as-synthesized samples were characterized by x-ray diffraction (XRD), scanning electron microscopy, absorption spectrum, photoluminescence (PL) and Raman spectroscopy. Size of the produced cubes could be controlled in the range 10 µm-50 nm by varying the solvent : co-solvent ratio. Micro-sized cubes could be grown in the presence of water as a solvent, while ethanol, which acts as a co-solvent, is found to be effective in reducing the size to the nanoscale. XRD results show complete crystalline structures in a griceite phase. The PL result of pure nanocubes exhibits a broad band in the range 370-550 nm, while that doped with Ag shows a prominent band at 420 nm. Raman spectra of the pure and Ag-doped LiF samples display several bands located in the range 80-236 cm-1. These results show that pure nanocubes of LiF have active colour centres without irradiation, which could be enhanced/modified by Ag dopants. This implies that these nanocubes might be useful in the development of optical devices.

Synthesis and characterization of nano- and microcrystalline cubes of pure and Ag-doped LiF

International Nuclear Information System (INIS)

Alharbi, Najlaa D; Salah, Numan; Habib, Sami S; Alarfaj, Esam

2013-01-01

Lithium fluoride (LiF) produced in single crystals and doped with proper activators is a highly sensitive phosphor used in several applications such as integrated optics, colour centre laser and radiation dosimetry. In this work, we have developed a new synthetic chemical co-precipitation route for the synthesis of well-crystallized micro- and nanocrystalline cubes of pure and silver (Ag)-doped LiF. The as-synthesized samples were characterized by x-ray diffraction (XRD), scanning electron microscopy, absorption spectrum, photoluminescence (PL) and Raman spectroscopy. Size of the produced cubes could be controlled in the range 10 µm-50 nm by varying the solvent:co-solvent ratio. Micro-sized cubes could be grown in the presence of water as a solvent, while ethanol, which acts as a co-solvent, is found to be effective in reducing the size to the nanoscale. XRD results show complete crystalline structures in a griceite phase. The PL result of pure nanocubes exhibits a broad band in the range 370-550 nm, while that doped with Ag shows a prominent band at 420 nm. Raman spectra of the pure and Ag-doped LiF samples display several bands located in the range 80-236 cm -1 . These results show that pure nanocubes of LiF have active colour centres without irradiation, which could be enhanced/modified by Ag dopants. This implies that these nanocubes might be useful in the development of optical devices.

Comparative investigation on cation-cation (Al-Sn) and cation-anion (Al-F) co-doping in RF sputtered ZnO thin films: Mechanistic insight

Energy Technology Data Exchange (ETDEWEB)

Mallick, Arindam; Basak, Durga, E-mail: sspdb@iacs.res.in

2017-07-15

Highlights: • Comparative study on Al, Al-Sn and Al-F doped ZnO films has been carried out. • High transparent Al-F co-doped film shows three times enhanced carrier density. • Al-F co-doped film shows larger carrier relaxation time. • Al-Sn co-doped films shows carrier transport dominated by impurity scattering. • Al-F co-doped ZnO film can be applied as transparent electrode. - Abstract: Herein, we report a comparative mechanistic study on cation-cation (Al-Sn) and cation-anion (Al-F) co-doped nanocrystalline ZnO thin films grown on glass substrate by RF sputtering technique. Through detailed analyses of crystal structure, surface morphology, microstructure, UV-VIS-NIR transmission-reflection and electrical transport property, the inherent characteristics of the co-doped films were revealed and compared. All the nanocrystalline films retain the hexagonal wurtzite structure of ZnO and show transparency above 90% in the visible and NIR region. As opposed to expectation, Al-Sn (ATZO) co-doped film show no enhanced carrier concentration consistent with the probable formation of SnO{sub 2} clusters supported by the X-ray photoelectron spectroscopy study. Most interestingly, it has been found that Al-F (AFZO) co-doped film shows three times enhanced carrier concentration as compared to Al doped and Al-Sn co-doped films attaining a value of ∼9 × 10{sup 20} cm{sup −3} due to the respective cation and anion substitution. The carrier relaxation time increases in AFZO while it decreases significantly for ATZO film consistent with the concurrence of the impurity scattering in the latter.

Hardening and embrittlement mechanisms of reduced activation ferritic/martensitic steels irradiated at 573 K

Energy Technology Data Exchange (ETDEWEB)

Tanigawa, H. [Japan Atomic Energy Agency, Tokai-mura, Naga-gun, Ibaraki-ken (Japan); Klueh, R.L. [Oak Ridge Noational Laboratory, TN (United States); Hashimoto, N. [Hokkaido Univ., Materials Science and Engineering Div., Graduate School of Engineering, Sapporo (Japan); Sokolov, M. [Oak Ridge National Laboratory, Materials Science and Technology Div., TN (United States)

2007-07-01

Full text of publication follows: It has been reported that reduced-activation ferritic/martensitic steels (RAFMs), such as F82H, ORNL9Cr-2WVTa, and JLF-1, showed a variety of changes in ductile-brittle transition temperature and yield stress after irradiation at 573 K up to 5 dpa, and those differences could not be interpreted solely by the difference of dislocation microstructure induced by irradiation. To investigate the impact of other microstructural feature, i.e. precipitates, the precipitation behavior of F82H, ORNL 9Cr-2WVTa, and JLF-1 was examined. It was revealed that irradiation-induced precipitation and amorphization of precipitates partly occurred and caused the different precipitation on block, packet and prior austenitic grain boundaries. In addition to these phenomena, irradiation-induced nano-size precipitates were also observed in the matrix. It was also revealed that the chemical compositions of precipitates approached the calculated thermal equilibrium state of M{sub 23}C{sub 6} at an irradiation temperature of 573 K. The calculation also suggests the presence of Laves phase at 573 K, which is usually not observed at this temperature, but the ion irradiation on aged F82H with Laves phase suggests that Laves phase becomes amorphous and could not be stable under irradiation at 573 K. This observation indicates the possibility that the irradiation-induced nano-size precipitation could be the consequence of the conflict between precipitation and amorphization of Laves phase. Over all, these observations suggests that the variety of embrittlement and hardening of RAFMs observed at 573 K irradiation up to 5 dpa might be the consequence of the transition phenomena that occur as the microstructure approaches thermal equilibrium during irradiation at 573 K. (authors)

Synthesis and photoluminescence properties of Sm3+-doped CaWO4 nanoparticles

International Nuclear Information System (INIS)

Xiao Qi; Zhou Qitao; Li Ming

2010-01-01

The Sm 3+ -doped CaWO 4 nanoparticles were synthesized by hydrothermal method. The room temperature photoluminescence (PL) spectra of Sm 3+ -doped CaWO 4 nanoparticles doped with different Sm 3+ concentrations under 405 nm excitation have been investigated. The PL spectra showed four strong emission peaks at 460, 571, 609, and 653 nm. The first emission peak at 460 nm could be due to a structural defect of the lattice, an oxygen-deficient WO 3 complex. The other three emissions at 571, 609, and 653 nm were due to the f-f forbidden transitions of the 4f electrons of Sm 3+ , corresponding to 4 G 5/2 → 6 H 5/2 (571 nm), 6 H 7/2 (609 nm), and 6 H 9/2 (653 nm), respectively. In addition, the optimum Sm 3+ concentration in CaWO 4 nanoparticles for optical emission was determined to be 1.0%. The Sm 3+4 G 5/2 → 6 H 7/2 (609 nm) emission intensity of Sm 3+ -doped CaWO 4 nanoparticles significantly increased with the increase of Sm 3+ concentration, and showed a maximum when Sm 3+ doping content was 1.0%. If Sm 3+ concentration continued to increase, namely more than 1.0%, the Sm 3+4 G 5/2 → 6 H 7/2 emission intensity would decrease. The present materials might be a promising phosphor for white-light LED applications.

Nitrogen doping efficiency during vapor phase epitaxy of 4H-SiC

Energy Technology Data Exchange (ETDEWEB)

Rowland, L.B.; Brandt, C.D. [Northrop Grumman Science and Technology Center, Pittsburgh, PA (United States); Burk, A.A. Jr. [Northrop Grumman Advanced Technology Lab., Baltimore, MD (United States)

1998-06-01

This work examines the interrelationships among doping efficiency, mole fraction, and Si/C ratio for intentional doping of 4H-SiC during vapor phase epitaxy using N{sub 2}. For four Si/C ratios, the doping concentration increased linearly as a function of increasing N{sub 2} partial pressure with a slope of 1.0 {+-} 0.03. Variation of propane mole fraction while the SiH{sub 4} and N{sub 2} mole fractions were kept constant revealed two different modes of nitrogen incorporation, corresponding to carbon-rich and silicon-rich conditions. (orig.) 14 refs.

Influence of a doping by Al stainless steel on kinetics and character of interaction with the metallic nuclear fuel

Science.gov (United States)

Nikitin, S. N.; Shornikov, D. P.; Tarasov, B. A.; Baranov, V. G.

2016-04-01

Metallic nuclear fuel is a perspective kind of fuel for fast reactors. In this paper we conducted a study of the interaction between uranium-molybdenum alloy and ferritic- martensitic steels with additions of aluminum at a temperature of 700 ° C for 25 hours. The rate constants of the interaction layer growth at 700 °C is about 2.8.10-14 m2/s. It is established that doping Al stainless steel leads to decrease in interaction with uranium-molybdenum alloys. The phase composition of the interaction layer is determined.

A Study on the Fatigue-Fractured Surface of Normalized SS41 Steel and M.E.F. Dual Phase Steel by an X-ray Diffraction Technique

International Nuclear Information System (INIS)

Oh, Sae Wook; Park, Young Chul; Park, Soo Young; Kim, Deug Jin; Hue, Sun Chul

1996-01-01

This study verified the relationship between fracture mechanics parameters and X-ray parameters for normalized SS41 steel with homogeneous crystal structure and M.E.F. dual phase steel(martensite encapsulated islands of ferrite). The fatigue crack propagation test were carried out and X-ray diffraction technique was applied to fatigue fractured surface. The change in X-ray parameters(residual stress, half-value breadth) according to the depth of fatigue fractured surface were investigated. The depth of maximum plastic zone, W y , were determined on the basis of the distribution of the half-value breadth for normalized SS41 steel and that of the residual stress for M.E.F. dual phase steel. K max could be estimated by the measurement of W y

Impurity content of reduced-activation ferritic steels and a vanadium alloy

International Nuclear Information System (INIS)

Klueh, R.L.; Grossbeck, M.L.; Bloom, E.E.

1997-01-01

Inductively coupled plasma mass spectrometry was used to analyze a reduced-activation ferritic/martensitic steel and a vanadium alloy for low-level impurities that would compromise the reduced-activation characteristics of these materials. The ferritic steel was from the 5-ton IEA heat of modified F82H, and the vanadium alloy was from a 500-kg heat of V-4Cr-4Ti. To compare techniques for analysis of low concentrations of impurities, the vanadium alloy was also examined by glow discharge mass spectrometry. Two other reduced-activation steels and two commercial ferritic steels were also analyzed to determine the difference in the level of the detrimental impurities in the IEA heat and steels for which no extra effort was made to restrict some of the tramp impurities. Silver, cobalt, molybdenum, and niobium proved to be the tramp impurities of most importance. The levels observed in these two materials produced with present technology exceeded the limits for low activation for either shallow land burial or recycling. The chemical analyses provide a benchmark for the improvement in production technology required to achieve reduced activation; they also provide a set of concentrations for calculating decay characteristics for reduced-activation materials. The results indicate the progress that has been made and give an indication of what must still be done before the reduced-activation criteria can be achieved

Highly transparent and conductive Sn/F and Al co-doped ZnO thin films prepared by sol–gel method

International Nuclear Information System (INIS)

Pan, Zhanchang; Luo, Junming; Tian, Xinlong; Wu, Shoukun; Chen, Chun; Deng, Jianfeng; Xiao, Chumin; Hu, Guanghui; Wei, Zhigang

2014-01-01

Highlights: • F/Sn and Al co-doped ZnO thin films were synthesized by sol–gel method. • The co-doped nanocrystals exhibit good crystal quality. • The origin of the photoluminescence emissions was discussed. • The films showed high transmittance and low resistivity. -- Abstract: Al doped ZnO, Al–Sn co-doped ZnO and Al–F co-doped ZnO nanocrystals were successfully synthesized onto glass substrates by the sol–gel method. The structure and morphology of the films are characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and high resolution transmission electron microscopy (HRTEM). The results indicated that all the films were polycrystalline with a hexagonal wurtzite structure and exhibited a c-axis preferred orientation. The electrical and optical properties were also investigated by 4-point probe device and Uv–vis spectroscopy, room temperature photoluminescence (PL) and Raman spectrum (Raman), respectively. The PL and Raman results suggested that the co-doped films with a very low defect concentration and exhibit a better crystallinity than AZO thin films. The XPS study confirmed the incorporation of Al, Sn and F ions in the ZnO lattice

Upconversion improvement in KLaF{sub 4}:Yb{sup 3+}/Er{sup 3+} nanoparticles by doping Al{sup 3+} ions

Energy Technology Data Exchange (ETDEWEB)

Zhou, Haifang [Fuzhou University, School of Physics and Information Engineering, and Institute of Micro-Nano Devices and Solar Cells, Fuzhou (China); Jiangsu Collaborative Innovation Center of Photovoltaic Science and Engineering, Changzhou, Jiangsu (China); Wang, Xiechun; Lai, Yunfeng; Cheng, Shuying; Zheng, Qiao; Yu, Jinlin [Fuzhou University, School of Physics and Information Engineering, and Institute of Micro-Nano Devices and Solar Cells, Fuzhou (China)

2017-10-15

Rare-earth ion-doped upconversion (UC) materials show great potential applications in optical and optoelectronic devices due to their novel optical properties. In this work, hexagonal KLaF{sub 4}:Yb{sup 3+}/Er{sup 3+} nanoparticles (NPs) were successfully synthesized by a hydrothermal method, and remarkably enhanced upconversion luminescence in green and red emission bands in KLaF{sub 4}:Yb{sup 3+}/Er{sup 3+} NPs has been achieved by doping Al{sup 3+} ions under 980 nm excitation. Compared to the aluminum-free KLaF{sub 4}:Yb{sup 3+}/Er{sup 3+} NPs sample, the UC fluorescence intensities of the green and red emissions of NPs doped with 10 at.% Al{sup 3+} ions were significantly enhanced by 5.9 and 7.3 times, respectively. Longer lifetimes of the doped samples were observed for the {sup 4}S{sub 3/2} state and {sup 4}F{sub 9/2} state. The underlying reason for the UC enhancement by doping Al{sup 3+} ions was mainly ascribed to distortion of the local symmetry around Er{sup 3+} ions and adsorption reduction of organic ligands on the surface of NPs. In addition, the influence of doping Al{sup 3+} ions on the structure and morphology of the NPs samples was also discussed. (orig.)

Hydrogen Storage Characteristics of CNT doped NaAlH4

International Nuclear Information System (INIS)

Pukazhselvan, D.; Sterlin Leo Hudson, M.; Bipin Kumar Gupta; Srivastava, O.N.

2006-01-01

The current Hydrogen based energy infrastructure required a high energy density consumer friendly hydrogen storage media. Although the desired goals for the hydrogen fueled vehicular transport has not yet met by any hydrogen storage material, complex Sodium Alanate is said to be a promising candidate under this demand due to its high hydrogen storage capacity and the thermodynamically permissible reversible hydrogen storage capacity. However its poor sorption behavior under moderate conditions (NaAlH 4 →Na 3 AlH 6 ; 3.7 wt % vs 50 hrs at ∼170 C and Na 3 AlH 6 →NaH; 1.85 wt % vs 30 hrs at ∼220 C) urges their limited uses in ages. But these limitations can be removed by using catalysts particularly transition elements but the location of catalyst in NaAlH 4 matrix and the possible mechanism is not yet clearly understood. The aim of the present investigation is to improve the overall sorption characteristics of NaAlH 4 by a new light weighted high surface area (1315 sq mtr/gm) material (CNT) admixing and to obtain a best doping level to NaAlH 4 . So far only Ti has been attempted as a suitable catalyst. It is believed that the high surface area of CNT can provide an additional solid-gas (H 2 ) surface/interface and it can produce thermal contact between grains (thermal conductivity Kth of MWCNT: 3000 w/k and Kth of NaAlH 4 : 0.32 w/k) for stimulating their thermally activated dissociation in NaAlH 4 . In parallel with this approach XRD of NaAlH 4 reveals that there was no change in lattice structure after doping by CNT, SEM picture depicts that CNT precipitation in grain surfaces. Catalytic concentration of various mole % of x values finds that x = 8 is the best doping level as it gives 3.3 wt % of hydrogen within 2 hrs. The comparative sorption behavior with Ti:NaAlH 4 also shows CNTs as an optimum alternative catalyst to NaAlH 4 and besides this CNT doped desorbed ingredients shown good re-hydrogenation behavior(3.7 wt % at 8. cycle and 4.2 wt % maximum at

Thermal neutron imaging with rare-earth-ion-doped LiCaAlF6 scintillators and a sealed 252Cf source

International Nuclear Information System (INIS)

Kawaguchi, Noriaki; Yanagida, Takayuki; Fujimoto, Yutaka; Yokota, Yuui; Kamada, Kei; Fukuda, Kentaro; Suyama, Toshihisa; Watanabe, Kenichi; Yamazaki, Atsushi; Chani, Valery; Yoshikawa, Akira

2011-01-01

Thermal neutron imaging with Ce-doped LiCaAlF 6 crystals has been performed. The prototype of the neutron imager using a Ce-doped LiCaAlF 6 scintillating crystal and a position sensitive photomultiplier tube (PSPMT) which had 64 multi-channel anode was developed. The Ce-doped LiCaAlF 6 single crystal was grown by the Czochralski method. A plate with dimensions of a diameter of 50x2 mm 2 was cut from the grown crystal, polished, and optically coupled to PSPMT by silicone grease. The 252 Cf source ( 6 .

Upconversion emission and cathodoluminescence of Er{sup 3+}-doped NaYbF{sub 4} nanoparticles for low-temperature thermometry and field emission displays

Energy Technology Data Exchange (ETDEWEB)

Du, Peng; Yu, Jae Su [Kyung Hee University, Department of Electronics and Radio Engineering, Yongin (Korea, Republic of); Luo, Laihui [Ningbo University, Department of Microelectronic Science and Engineering, Ningbo (China)

2017-03-15

The Er{sup 3+}-doped NaYbF{sub 4} nanoparticles were fabricated by a hydrothermal method. The green and red emissions located at around 525, 542 and 657 nm corresponding to the {sup 2}H{sub 11/2} → {sup 4}I{sub 15/2}, {sup 4}S{sub 3/2} → {sup 4}I{sub 15/2} and {sup 4}F{sub 9/2} → {sup 4}I{sub 15/2} transitions of Er{sup 3+} ions, respectively, were observed when pumped at 980 nm light. Furthermore, with the help of the fluorescence intensity ratio technique, the thermometric properties of as-prepared products from the thermally coupled {sup 2}H{sub 11/2} and {sup 4}S{sub 3/2} levels of Er{sup 3+} ions were studied by analyzing temperature-dependent upconversion (UC) emission spectra. The maximum sensitivity for the Er{sup 3+}-doped NaYbF{sub 4} nanoparticles was found to be around 0.0043 K{sup -} {sup 1} with a temperature range of 93-293 K. In addition, the cathodoluminescence (CL) spectrum of the synthesized nanoparticles was nearly the same as the UC emission spectrum and the CL emission intensity did not exhibit saturation with the increase of accelerating voltage and filament current. (orig.)

Effects of disorder on the intrinsically hole-doped iron-based superconductor KC a2F e4A s4F2 by cobalt substitution

Science.gov (United States)

Ishida, Junichi; Iimura, Soshi; Hosono, Hideo

2017-11-01

In this paper, the effects of cobalt substitution on the transport and electronic properties of the recently discovered iron-based superconductor KC a2F e4A s4F2 , with Tc=33 K , are reported. This material is an unusual superconductor showing intrinsic hole conduction (0.25 holes /F e2 + ). Upon doping of Co, the Tc of KC a2(Fe1-xC ox) 4A s4F2 gradually decreased, and bulk superconductivity disappeared when x ≥0.25 . Conversion of the primary carrier from p type to n type upon Co-doping was clearly confirmed by Hall measurements, and our results are consistent with the change in the calculated Fermi surface. Nevertheless, neither spin density wave (SDW) nor an orthorhombic phase, which are commonly observed for nondoped iron-based superconductors, was observed in the nondoped or electron-doped samples. The electron count in the 3 d orbitals and structural parameters were compared with those of other iron-based superconductors to show that the physical properties can be primarily ascribed to the effects of disorder.

Partial substitution of vanadium by niobium in AISI H13 steel

International Nuclear Information System (INIS)

Itman Filho, A.; Balancin, O.

1987-01-01

The aim of this work was to study the tempering resistence in conditions of use of the AISI H13 steel, after partial substitution of vanadium by niobium. Four alloys of this steel were elaborated and in three of them the niobim was added in the contents of 0,2; 0,5 and 1,0%. Metallographic techniques were performed to compare qualitatively the niobium effect in several processing and thermal analisys of the steels. Grain size measurements were made after austenitization of the steels, hardness measurements in prepared samples were made after quenching and tempering, tensile testing at elevated temperature was investigated and yield strength, reduction of area after steel breaking and elongation were calculated. After these studies it was possible to certify that the partial substitution of vanadium by niobium did not alter significantly the basic mechanical properties of the AISI H13. (Author) [pt

Intrinsic Defects and H Doping in WO3

KAUST Repository

Zhu, Jiajie; Vasilopoulou, Maria; Davazoglou, Dimitris; Kennou, Stella; Chroneos, Alexander; Schwingenschlö gl, Udo

2017-01-01

WO3 is widely used as industrial catalyst. Intrinsic and/or extrinsic defects can tune the electronic properties and extend applications to gas sensors and optoelectonics. However, H doping is a challenge to WO3, the relevant mechanisms being hardly

Recent status and improvement of reduced-activation ferritic-martensitic steels for high-temperature service

Energy Technology Data Exchange (ETDEWEB)

Tan, L., E-mail: tanl@ornl.gov [Oak Ridge National Laboratory, Oak Ridge, TN, 37831 (United States); Katoh, Y. [Oak Ridge National Laboratory, Oak Ridge, TN, 37831 (United States); Tavassoli, A.-A.F.; Henry, J. [DMN/Dir, DEN, CEA Saclay, 91191, Gif-sur-Yvette Cedex (France); Rieth, M. [Karlsruhe Institute of Technology, Karlsruhe, 76021 (Germany); Sakasegawa, H. [National Institutes for Quantum and Radiological Science and Technology, Rokkasho, Aomori, 039-3212 (Japan); Oak Ridge National Laboratory, Oak Ridge, TN, 37831 (United States); Tanigawa, H. [National Institutes for Quantum and Radiological Science and Technology, Rokkasho, Aomori, 039-3212 (Japan); Huang, Q. [Institute of Nuclear Energy Safety Technology, Chinese Academy of Sciences, Hefei, Anhui, 230031 (China)

2016-10-15

Reduced-activation ferritic-martensitic (RAFM) steels, candidate structural materials for fusion reactors, have achieved technological maturity after about three decades of research and development. The recent status of a few developmental aspects of current RAFM steels, such as aging resistance, plate thickness effects, fracture toughness, and fatigue, is updated in this paper, together with ongoing efforts to develop next-generation RAFM steels for superior high-temperature performance. In addition to thermomechanical treatments, including nonstandard heat treatment, alloy chemistry refinements and modifications have demonstrated some improvements in high-temperature performance. Castable nanostructured alloys (CNAs) were developed by significantly increasing the amount of nanoscale MX (M = V/Ta/Ti, X = C/N) precipitates and reducing coarse M{sub 23}C{sub 6} (M = Cr). Preliminary results showed promising improvement in creep resistance and Charpy impact toughness. Limited low-dose neutron irradiation results for one of the CNAs and China low activation martensitic are presented and compared with data for F82H and Eurofer97 irradiated up to ∼70 displacements per atom at ∼300–325 °C.

Mixed-mode I/III fracture toughness of a ferritic/martensitic stainless steel

International Nuclear Information System (INIS)

Li, Huaxin; Jones, R.H.; Gelles, D.S.; Hirth, J.P.

1993-10-01

The critical J-integrals of mode I (J IC ), mixed-mode I/III (J MC ), and mode III (J IIIC ) were examined for a ferritic stainless steel (F-82H) at ambient temperature. A determination of J MC was made using modified compact-tension specimens. Different ratios of tension/shear stress were achieved by varying the principal axis of the crack plane between 0 and 55 degrees from the load line. Results showed that J MC and tearing modulus (T M ) values varied with the crack angles and were lower than their mode I and mode III counterparts. Both the minimum J MC and T M values occurred at a crack angle between 40 and 50 degrees, where the load ratio of σ i /σ iii was 1.2 to 0.84. The J min was 240 Kj/M 2 , and ratios of J IC /J min and J IIIC /J min were 2.1 and 1.9, respectively. The morphology of fracture surfaces was consistent with the change of J MC and T M values. While the upper shelf-fracture toughness of F-82H depends on loading mode, the J min remains very high. Other important considerations include the effect of mixed-mode loading on the DBT temperature, and effects of hydrogen and irradiation on J min

Improved Dehydrogenation Properties of 2LiNH2-MgH2 by Doping with Li3AlH6

Directory of Open Access Journals (Sweden)

Shujun Qiu

2017-01-01

Full Text Available Doping with additives in a Li-Mg-N-H system has been regarded as one of the most effective methods of improving hydrogen storage properties. In this paper, we prepared Li3AlH6 and evaluated its effect on the dehydrogenation properties of 2LiNH2-MgH2. Our studies show that doping with Li3AlH6 could effectively lower the dehydrogenation temperatures and increase the hydrogen content of 2LiNH2-MgH2. For example, 2LiNH2-MgH2-0.1Li3AlH6 can desorb 6.43 wt % of hydrogen upon heating to 300 °C, with the onset dehydrogenation temperature at 78 °C. Isothermal dehydrogenation testing indicated that 2LiNH2-MgH2-0.1Li3AlH6 had superior dehydrogenation kinetics at low temperature. Moreover, the release of byproduct NH3 was successfully suppressed. Measurement of the thermal diffusivity suggests that the enhanced dehydrogenation properties may be ascribed to the fact that doping with Li3AlH6 could improve the heat transfer for solid–solid reaction.

Decapado de un acero inoxidable austenítico mediante mezclas ecológicas basadas en H2O2 - H2SO4 - iones F-

Directory of Open Access Journals (Sweden)

Narváez, L.

2013-04-01

Full Text Available This study reports the pickling of 316L stainless steel using mixtures of hydrogen peroxide (H2O2, sulphuric acid (H2SO4 and fluoride ions as hydrofluoric acid (HF, sodium fluoride (NaF and potassium fluoride (KF. The decomposition of H2O2 in the mixtures was assessed at different temperatures 25 °C to 60 °C, with ferric ion contents from 0 to 40 g/l. According to the results obtained, were established the optimal condition pickling at 20 g/l of ferric ions, 25 °C and p-toluensulphonic acid as stabilizer of H2O2. The HF pickling mixture was the only capable to remove totally the oxide layer from the 316L stainless steel after 300 s. The fluoride salts pickling mixtures only remove partially the oxide layer (20 to 40 % aprox. after 300 s. When the pickling time was increased until 1200 s, the removal percentages were around to 80 %.En este estudio se presenta el decapado del acero inoxidable austenítico 316L utilizando mezclas de peróxido de hidrógeno (H2O2/ácido sulfúrico (H2SO4/iones fluoruro; los iones fluoruro provienen del ácido fluorhídrico (HF, fluoruro de sodio (NaF y fluoruro de potasio (KF. La estabilidad del H2O2 fue valorada modificando las concentraciones del ión férrico de 0 a 40 g/l y las temperaturas de 25 °C a 60 °C en las mezclas decapantes. Se establecieron las condiciones óptimas de decapado utilizando 20 g/l de iones férrico a 25 °C empleando el ácido p-toluensulfónico como estabilizante del H2O2. La mezcla que contenía HF fue la única capaz de eliminar completamente los óxidos superficiales del acero a tiempos de 300 s. Las mezclas a base de sales fluoradas eliminaron parcialmente los óxidos (20 y 40 % aprox. en 300 s. Al incrementar el tiempo de decapado hasta 1200 s se obtuvieron porcentajes de eliminación alrededor de un 80 %.

Modeling of helium bubble nucleation and growth in neutron irradiated boron doped RAFM steels

International Nuclear Information System (INIS)

Dethloff, Christian; Gaganidze, Ermile; Svetukhin, Vyacheslav V.; Aktaa, Jarir

2012-01-01

Reduced activation ferritic/martensitic (RAFM) steels are promising candidates for structural materials in future fusion technology. In addition to other irradiation defects, the transmuted helium is believed to strongly influence material hardening and embrittlement behavior. A phenomenological model based on kinetic rate equations is developed to describe homogeneous nucleation and growth of helium bubbles in neutron irradiated RAFM steels. The model is adapted to different 10 B doped EUROFER97 based heats, which already had been studied in past irradiation experiments. Simulations yield bubble size distributions, whereby effects of helium generation rate, surface energy, helium sinks and helium density are investigated. Peak bubble diameters under different conditions are compared to preliminary microstructural results on irradiated specimens. Helium induced hardening was calculated by applying the Dispersed Barrier Hardening model to simulated cluster size distributions. Quantitative microstructural investigations of unirradiated and irradiated specimens will be used to support and verify the model.

Modeling of helium bubble nucleation and growth in neutron irradiated boron doped RAFM steels

Energy Technology Data Exchange (ETDEWEB)

Dethloff, Christian, E-mail: christian.dethloff@kit.edu [Karlsruhe Institute of Technology (KIT), Institute for Applied Materials, Hermann-von-Helmholtz-Platz 1, 76344 Eggenstein-Leopoldshafen (Germany); Gaganidze, Ermile [Karlsruhe Institute of Technology (KIT), Institute for Applied Materials, Hermann-von-Helmholtz-Platz 1, 76344 Eggenstein-Leopoldshafen (Germany); Svetukhin, Vyacheslav V. [Ulyanovsk State University, Leo Tolstoy Str. 42, 432970 Ulyanovsk (Russian Federation); Aktaa, Jarir [Karlsruhe Institute of Technology (KIT), Institute for Applied Materials, Hermann-von-Helmholtz-Platz 1, 76344 Eggenstein-Leopoldshafen (Germany)

2012-07-15

Reduced activation ferritic/martensitic (RAFM) steels are promising candidates for structural materials in future fusion technology. In addition to other irradiation defects, the transmuted helium is believed to strongly influence material hardening and embrittlement behavior. A phenomenological model based on kinetic rate equations is developed to describe homogeneous nucleation and growth of helium bubbles in neutron irradiated RAFM steels. The model is adapted to different {sup 10}B doped EUROFER97 based heats, which already had been studied in past irradiation experiments. Simulations yield bubble size distributions, whereby effects of helium generation rate, surface energy, helium sinks and helium density are investigated. Peak bubble diameters under different conditions are compared to preliminary microstructural results on irradiated specimens. Helium induced hardening was calculated by applying the Dispersed Barrier Hardening model to simulated cluster size distributions. Quantitative microstructural investigations of unirradiated and irradiated specimens will be used to support and verify the model.

Corrosion fatigue crack growth in clad low-alloy steels: Part 1, medium-sulfur forging steel

International Nuclear Information System (INIS)

James, L.A.; Poskie, T.J.; Auten, T.A.; Cullen, W.H.

1996-01-01

Corrosion fatigue crack propagation tests were conducted on a medium- sulfur ASTM A508-2 forging steel overlaid with weld-deposited Alloy EN82H cladding. The specimens featured semi-elliptical surface cracks penetrating approximately 6.3 mm of cladding into the underlying steel. The initial crack sizes were relatively large with surface lengths of 30.3--38.3 mm, and depths of 13.1--16.8 mm. The experiments were conducted in a quasi-stagnant low-oxygen (O 2 < 10 ppb) aqueous environment at 243 degrees C, under loading conditions (ΔK, R, and cyclic frequency) conductive to environmentally-assisted cracking (EAC) in higher-sulfur steels under quasi-stagnant conditions. Earlier experiments on unclad compact tension specimens of this heat of steel did not exhibit EAC, and the present experiments on semi-elliptical surface cracks penetrating cladding also did not exhibit EAC

Struvite recovery from swine waste biogas digester effluent through a stainless steel device under constant pH conditions.

Science.gov (United States)

Perera, P W Anton; Wu, Wei-Xiang; Chen, Ying-Xu; Han, Zhi-Ying

2009-06-01

To investigate the struvite precipitation under constant and non-constant pH conditions and to test a stainless steel device under different operating regimes to maximize the recovery of struvite. The molar ratio of NH4+: Mg2+: PO4(3-) was adjusted to 1: 1.2: 1.2 and pH was elevated to 9.0. The absorbance measurement was used to trace the process of struvite crystallization. Wastewater and precipitate analysis was done by standard analytical methods. The pH constant experiment reported a significantly higher struvite precipitation (24.6 +/- 0.86 g) than the non-constant pH experiment (19.8 +/- 1.86 g). The SAR ranged from 5.6 to 8.2 g m(-2) h(-1) to 3.6-4.8 g m(-2) h(-1) in pH constant and non-constant experiments, respectively. The highest struvite deposit on the device was found in regime 3 followed by in regimes 2 and 4. The highest PO4(3-) (97.2%) and NH4+ (71%) removal was reported in the R1 regime. None of the influent Cu2+ or Zn2+ was precipitated on the device. A higher struvite yield is evident in pH constant experiments. Moreover, the stainless steel device facilitates the isolation of heavy metal free pure (around 96%) struvite from swine waste biogas digester effluent contaminated with cu2+ and Zn2+ and the highest yield is attainable with the device operating at 50 rpm with agitation by a magnetic stirrer.

Hydrogen degradation of the 26H2MF alloy steel in H2SO4 and hydrocarbon environments

International Nuclear Information System (INIS)

Zielinski, A.; Swieczko-Zurek, B.; Michaliak, P.

2004-01-01

The Polish 26H2M alloy steel has been subjected to different heat treatment resulting in different microstructure and fracture appearance. The slow strain rate tests have been made on smooth round specimens in diluted sulphuric acid, boiler fuel and used mineral machine oil. The 26H2MF steel has become relatively immune in neutral boiler fuel and mineral oil and been heavily suffered from hydrogen degradation in acidic environment. The results demonstrate that the 26H2MF steel is highly susceptible to hydrogen degradation but in absence of stress raisers the increased hydrogen absorption in hydrocarbons can cause only small loss of its plasticity. (author) >>>

Spectroscopic properties of Er3+ and Yb3+ co-doped glass ceramics containing SrF2 nanocrystals

International Nuclear Information System (INIS)

Qiao Xvsheng; Fan Xianping; Wang Minquan; Zhang Xianghua

2009-01-01

The spectroscopic properties of Er 3+ /Yb 3+ co-doped 50SiO 2 -10Al 2 O 3 -20ZnF 2 -20SrF 2 glass and glass ceramic containing SrF 2 nanocrystals were investigated. The formation of SrF 2 nanocrystals in the glass ceramic was confirmed by XRD. The oscillator strengths for several transitions of the Er 3+ ions in the glass ceramic have been obtained and the Judd-Ofelt parameters were then determined. The XRD result and Judd-Ofelt parameters suggested that Er 3+ and Yb 3+ ions had efficiently enriched in the SrF 2 nanocrystals in the glass ceramic. The lifetime of excited states has been used to reveal the surroundings of luminescent Er 3+ and Yb 3+ and energy transfer (ET) mechanism between Er 3+ and Yb 3+ . Much stronger upconversion luminescence and longer lifetime of the Er 3+ /Yb 3+ co-doped glass ceramic were observed in comparison with the Er 3+ /Yb 3+ co-doped glass, which could be ascribed to more efficient ET from Yb 3+ to Er 3+ due to the enrichment of Yb 3+ and Er 3+ and the shortening of the distance between lanthanide ions in the precipitated SrF 2 nanocrystals.

Technical issues of RAFMs for the fabrication of ITER Test Blanket Module

International Nuclear Information System (INIS)

Tanigawa, Hiroyasu; Hirose, Takanori; Shiba, Kiyoyuki

2007-01-01

Reduced activation ferritic/martensitic steels (RAFMs) are recognized as the primary candidate structural materials for fusion blanket systems, as it has they have been developed based on massive industrial experience of ferritic/martensitic steel replacing Mo and Nb of high chromium heat resistant martensitic steels (such as modified 9Cr-1Mo) with W and Ta, respectively. F82H and JLF-1 are RAFMs, which have been developed and studied in Japan and the various effects of irradiation were reported. F82H is designed with emphasis on high temperature property and weldability, and was provided and evaluated in various countries as a part of the IEA fusion materials development collaboration. The JAEA/US collaboration program also has been conducted with the emphasis on irradiation effects of F82H. Now, among the existing database for RAFMs the most extensive one is that for F82H. The objective of this paper is to review the R and D status of F82H and to identify the key technical issues for the fabrication of ITER Test Blanket Module (TBM) suggested from the recent achievements in Japan. It is desirable to make the status of RAFMs equivalent to commercial steels to use RAFMs as the ITER-TBM structural material. This would require demonstrating the reproducibility and weldability as well as providing the database. The excellent reproducibility of F82H has been demonstrated with four 5-ton-heats, and two of them were provided as F82H-IEA heats. It has been also proved that F82H could be provided as plates (thickness of 1.5 to 55 mm), pipes and rectangular tubes. It is also important to have the excellent weldability as the TBM has about 300m length of weld line, and it was proved through TIG, EB and YAG weld test performed in air atmosphere. Various mechanical and microstructural data have been accumulated including long-term tests such as creep rupture tests and aging tests. Although F82H is a well-perceived RAFM as the ITER-TBM structural material, some issues are

Improved hydrogen storage properties of LiAlH{sub 4} by mechanical milling with TiF{sub 3}

Energy Technology Data Exchange (ETDEWEB)

Zang, Lei; Cai, Jiaxing; Zhao, Lipeng; Gao, Wenhong; Liu, Jian, E-mail: liujian@nankai.eud.cn; Wang, Yijing

2015-10-25

Dehydrogenation behavior of LiAlH{sub 4} (lithium alanate) admixed with TiF{sub 3} is investigated by pressure-composition-temperature (PCT), fourier transform infrared spectroscopy (FTIR), X-ray Diffraction (XRD), differential scanning calorimetry (DSC) and temperature programmed desorption (TPD). The TiF{sub 3} addition enhances kinetics of LiAlH{sub 4} and decreases the decomposition temperature. The LiAlH{sub 4}-2 mol % TiF{sub 3} sample starts to release hydrogen at about 35 °C and the dehydrogenation rate reaches a maximum value at 108.4 °C, compared with 145 °C and 179.9 °C for the as-received LiAlH{sub 4}. As for the dehydrogenation kinetics, the LiAlH{sub 4}-2 mol % TiF{sub 3} sample releases about 7.0 wt % H{sub 2} at 140 °C within 80 min. In comparison, the as-received LiAlH{sub 4} sample releases only 0.8 wt % hydrogen under the same conditions. The existence of proposed catalyst, Al{sub 3}Ti formed in-situ in the process of dehydrogenation, has been confirmed experimentally by XRD measurements. The activation energy of LiAlH{sub 4}-2 mol % TiF{sub 3} composite is deduced to be 66.76 kJ mol{sup −1} and 88.21 kJ mol{sup −1} for the first and second reaction stages of LiAlH{sub 4} dehydrogenation. - Highlights: • TiF{sub 3} considerably enhances the dehydrogenation kinetics of LiAlH{sub 4}. • TiF{sub 3}-doped LiAlH{sub 4} dehydrogenates even at room temperature. • Low activation energy of the dehydrogenation reaction. • Al{sub 3}Ti formed in-situ helps to explain the dehydrogenation mechanism.

Magnetic phase investigations on fluorine (F) doped LiFePO4

Science.gov (United States)

Radhamani, A. V.

2018-03-01

LiFePO4 (LFP) is a very promising cathode material for Li-ion batteries due to its high thermal stability, less toxicity and high theoretical capacity (170 mAh g-1). Anion doping, especially fluorine (F) at the oxygen site is one way to improve the low electronic conductivity of the material. In this line, fluorine doped LFP was prepared at different fluorine concentrations (1 to 40 mol%) to study the structural, spectroscopic and magnetic properties in view of the material property optimization for battery applications. The investigation of the magnetic properties was found to be successful for the determination of small amounts of magnetic impurities which were not noticeably observed from structural characterizations. Determination of conducting magnetic impurities has its own relevance in the current scenario of Li-ion based battery applications. Systematic characterization studies along with the implications of magnetic phases on the material activity of fluorine doped LiFePO4 nanoparticles will be discussed in detail.

Process dependence of H passivation and doping in H-implanted ZnO

International Nuclear Information System (INIS)

Zhang, Z; Brillson, L J; Look, D C; Schifano, R; Johansen, K M; Svensson, B G

2013-01-01

We used depth-resolved cathodoluminescence spectroscopy (DRCLS), photoluminescence (PL) spectroscopy and temperature-dependent Hall-effect (TDHE) measurements to describe the strong dependence of H passivation and doping in H-implanted ZnO on thermal treatment. Increasing H implantation dose increases passivation of Zn and oxygen vacancy-related defects, while reducing deep level emissions. Over annealing temperatures of 100-400 °C at different times, 1 h annealing at 200 °C yielded the lowest DRCLS deep level emissions, highest TDHE carrier mobility, and highest near band-edge PL emission. These results describe the systematics of dopant implantation and thermal activation on H incorporation in ZnO and their effects on its electrical properties.

VUV spectroscopy of Tm3+ and Mn2+ doped LiSrAlF6

International Nuclear Information System (INIS)

True, M.; Kirm, M.; Negodine, E.; Vielhauer, S.; Zimmerer, G.

2004-01-01

LiSrAlF 6 (LiSAF) crystals doped with either Tm 3+ or Mn 2+ were obtained by solid-state reaction and investigated spectroscopically using synchrotron radiation in the vacuum-ultra-violet and ultra-violet spectral regions. In the Tm 3+ doped LiSAF crystals, the slow spin-forbidden 5d-4f emission peaking at 166 nm with a lifetime of at least 1 μs was observed. The respective excitation spectrum consists of several bands in the range of 160-110 nm arising due to the 4f-5d absorption. The f-f emissions of Tm 3+ are well excited in the range of 135-110 nm, but not under excitation into the lower lying d-bands. The excitation mechanisms of different emissions will be discussed including the F - to Tm 3+ charge transfer excitation peaking at 127 nm in LiSAF. The characteristic broad 4 T 1 → 6 A 1 emission band of Mn 2+ peaking at 508 (504) nm was observed in LiSAF:Mn 2+ crystal at 10 (300) K. Three intense excitation bands, tentatively ascribed to the 3d-4s transitions of Mn 2+ , were revealed in the range of 170-110 nm

Study of wettability and cell viability of H implanted stainless steel

Science.gov (United States)

Shafique, Muhammad Ahsan; Ahmad, Riaz; Rehman, Ihtesham Ur

2018-03-01

In the present work, the effect of hydrogen ion implantation on surface wettability and biocompatibility of stainless steel is investigated. Hydrogen ions are implanted in the near-surface of stainless steel to facilitate hydrogen bonding at different doses with constant energy of 500 KeV, which consequently improve the surface wettability. Treated and untreated sample are characterized for surface wettability, incubation of hydroxyapatite and cell viability. Contact angle (CA) study reveals that surface wettability increases with increasing H-ion dose. Raman spectroscopy shows that precipitation of hydroxyapatite over the surface increase with increasing dose of H-ions. Cell viability study using MTT assay describes improved cell viability in treated samples as compared to the untreated sample. It is found that low dose of H-ions is more effective for cell proliferation and the cell count decreases with increasing ion dose. Our study demonstrates that H ion implantation improves the surface wettability and biocompatibility of stainless steel.

Proximity-induced spin-valley polarization in silicene or germanene on F-doped WS2

KAUST Repository

Sattar, Shahid

2016-11-11

Silicene and germanene are key materials for the field of valleytronics. However, interaction with the substrate, which is necessary to support the electronically active medium, becomes a major obstacle. In the present work, we propose a substrate (F-doped WS2) that avoids detrimental effects and at the same time induces the required valley polarization, so that no further steps are needed for this purpose. The behavior is explained by proximity effects on silicene or germanene, as demonstrated by first-principles calculations. Broken inversion symmetry due to the presence of WS2 opens a substantial band gap in silicene or germanene. F doping of WS2 results in spin polarization, which, in conjunction with proximity-enhanced spin-orbit coupling, creates sizable spin-valley polarization.

Thermomechanical modelling of laser surface glazing for H13 tool steel

Science.gov (United States)

Kabir, I. R.; Yin, D.; Tamanna, N.; Naher, S.

2018-03-01

A two-dimensional thermomechanical finite element (FE) model of laser surface glazing (LSG) has been developed for H13 tool steel. The direct coupling technique of ANSYS 17.2 (APDL) has been utilised to solve the transient thermomechanical process. A H13 tool steel cylindrical cross-section has been modelled for laser power 200 W and 300 W at constant 0.2 mm beam width and 0.15 ms residence time. The model can predict temperature distribution, stress-strain increments in elastic and plastic region with time and space. The crack formation tendency also can be assumed by analysing the von Mises stress in the heat-concentrated zone. Isotropic and kinematic hardening models have been applied separately to predict the after-yield phenomena. At 200 W laser power, the peak surface temperature achieved is 1520 K which is below the melting point (1727 K) of H13 tool steel. For laser power 300 W, the peak surface temperature is 2523 K. Tensile residual stresses on surface have been found after cooling, which are in agreement with literature. Isotropic model shows higher residual stress that increases with laser power. Conversely, kinematic model gives lower residual stress which decreases with laser power. Therefore, both plasticity models could work in LSG for H13 tool steel.

Effect of H, O intentionally doping on photoelectric properties in MOVPE-growth GaN layers

KAUST Repository

Ohkawa, Kazuhiro

2017-10-24

GaN crystal growth requires higher purity of materials. Some contaminants in NH3 gas could be the causal factor of defects in GaN crystals. These atoms act as donor or acceptor. In order to clearly demonstrate the effect of gaseous impurities such as H2O on the properties of undoped-GaN layer, high purity NH3 (N70) was used as NH3 source. The concentration of H2O in NH3 was varied at 32, 49, 75, 142, 266, 489, and 899 ppb, respectively. Under the same recipe, we deposited undoped-GaN epitaxial layer with purifier, and H2O-doped GaN series layers. As similar to the results of CO and CO2-doped GaN series, the increase tendency of carrier density changing with increasing H2O concentration. The FWHMs of XRC around (0002) remain stable, witnessing that the crystal quality of GaN layer remain good. LT (15K) PL of undoped-GaN and H2O-doped GaN were measured, the D0X emission peak intensity of all H2O-doped GaN are decreased drastically compared with undoped-GaN. H2O impurity was doped into GaN layer, which not only effects electrical properties and but also effects the radiative emission and furthermore effects PL intensity, its mechanism is discussed.

Simultaneous aluminizing and chromizing of steels to form (Fe,Cr){sub 3}Al coatings and Ge-doped silicide coatings of Cr-Zr base alloys

Energy Technology Data Exchange (ETDEWEB)

Zheng, M.; He, Y.R.; Rapp, R.A. [Ohio State Univ., Columbus, OH (United States). Dept. of Materials Science and Engineering

1997-12-01

A halide-activated cementation pack involving elemental Al and Cr powders has been used to achieve surface compositions of approximately Fe{sub 3}Al plus several percent Cr for low alloy steels (T11, T2 and T22) and medium carbon steel (1045 steel). A two-step treatment at 925 C and 1150 C yields the codeposition and diffusion of aluminum and chromium to form dense and uniform ferrite coatings of about 400 {micro}m thickness, while preventing the formation of a blocking chromium carbide at the substrate surfaces. Upon cyclic oxidation in air at 700 C, the coated steel exhibits a negligible 0.085 mg/cm{sup 2} weight gain for 1900 one-hour cycles. Virtually no attack was observed on coated steels tested at ABB in simulated boiler atmospheres at 500 C for 500 hours. But coatings with a surface composition of only 8 wt% Al and 6 wt% Cr suffered some sulfidation attack in simulated boiler atmospheres at temperatures higher than 500 C for 1000 hours. Two developmental Cr-Zr based Laves phase alloys (CN129-2 and CN117(Z)) were silicide/germanide coated. The cross-sections of the Ge-doped silicide coatings closely mimicked the microstructure of the substrate alloys. Cyclic oxidation in air at 1100 C showed that the Ge-doped silicide coating greatly improved the oxidation resistance of the Cr-Zr based alloys.

Effect of Al-doped on physical properties of ZnO Thin films grown by spray pyrolysis on SnO2: F/glass

Directory of Open Access Journals (Sweden)

Castagné M.

2012-06-01

Full Text Available Transparent conducting thin films of aluminum-doped zinc oxide (ZnO:Al have been deposited on SnO2:F/glass by the chemical spray technique, starting from zinc acetate (CH3CO22Zn.2H2O and aluminum chloride AlCl3. The effect of changing the aluminum-to-zinc ratio y from 0 to 3 at.%, has been thoroughly investigated. It was found that the optical and electrical properties of Al doped ZnO films improved with the addition of aluminum in the spray solution until y=2%. At this Al doping percentage, the thin layers have a resistivity equal to 4.1 × 10−4 Ω.cm and a transmittance of about 90 % in the region [600-1000] nm. XRD patterns confirm that the films have polycristalline nature and a wurtzite (hexagonal structure which characterized with (100, (002 and (101 principal orientations. The undoped films have (002 as the preferred orientation but Al doped ones have (101 as the preferred orientation. Beyond y= 1%, peak intensities decrease considerably.

Band gap opening of bilayer graphene by F4-TCNQ molecular doping and externally applied electric field.

Science.gov (United States)

Tian, Xiaoqing; Xu, Jianbin; Wang, Xiaomu

2010-09-09

The band gap opening of bilayer graphene with one side surface adsorption of F4-TCNQ is reported. F4-TCNQ doped bilayer graphene shows p-type semiconductor characteristics. With a F4-TCNQ concentration of 1.3 x 10(-10) mol/cm(2), the charge transfer between each F4-TCNQ molecule and graphene is 0.45e, and the built-in electric field, E(bi), between the graphene layers could reach 0.070 V/A. The charge transfer and band gap opening of the F4-TCNQ-doped graphene can be further modulated by an externally applied electric field (E(ext)). At 0.077 V/A, the gap opening at the Dirac point (K), DeltaE(K) = 306 meV, and the band gap, E(g) = 253 meV, are around 71% and 49% larger than those of the pristine bilayer under the same E(ext).

Technical issues of fabrication technologies of reduced activation ferritic/martensitic steels

International Nuclear Information System (INIS)

Tanigawa, Hiroyasu; Sakasegawa, Hideo; Hirose, Takanori

2013-01-01

Highlights: • The key technical issues of RAFM steel fabrication are the control of Ta, and deoxidation of the steel with a limited amount of Al addition. • Addition of Ta with poor deoxidation might results in the agglomeration of inclusions at 1/2t position. • ESR was proved to be effective removing Ta oxide inclusions and avoiding agglomeration of inclusions at 1/2t position, and achieving low oxygen concentration. -- Abstract: The key issue for DEMO application is that Reduced activation ferritic/martensitic (RAFM) steels fabrication technologies has to be highly assured, especially with respect to high availability, reliability and reduced activation capability on the DEMO level fabrication, which requires not a few tons but thousand tons RAFM fabrication. One of the key technical issues of RAFM fabrication is the control of Ta, and deoxidation of the steel with a limited amount of Al addition. The series of F82H (Fe–8Cr–2W–V, Ta) melting revealed that Ta have tendency to form oxide on melting process, and this will have large impact on reliability of the steels. Al is also the key elements, as it is commonly used for deoxidation of steels, and achieving lower oxygen level is essential to obtain good mechanical properties, but the maximum concentration of Al is limited in view of reduced activation capability. These tendency and limitation resulted in the Ta oxide agglomeration in the middle of plate, but the remelting process, ESR (electro slag remelting), was found to be successful on removing those Ta oxides

DFT insights into the electronic and optical properties of fluorine-doped monoclinic niobium pentoxide (B-Nb{sub 2}O{sub 5}:F)

Energy Technology Data Exchange (ETDEWEB)

El-Shazly, Tamer S.; Rehim, Sayed S.A. [Ain-Shams University, Chemistry Department, Faculty of Science, Cairo (Egypt); Hassan, Walid M.I. [Cairo University, Chemistry Department, Faculty of Science, Giza (Egypt); Allam, Nageh K. [American University in Cairo, Energy Materials Lab (EML), School of Sciences and Engineering, New Cairo (Egypt)

2016-09-15

We report on the effect of fluorine doping on the electronic structure and optical properties of monoclinic niobium pentoxide (B-Nb{sub 2}O{sub 5}) as revealed by the first principles calculations. Density functional theory (DFT) along with generalized gradient approximation (GGA) at the revised Perdew-Burke-Ernzerhof (PBEsol) exchange-correlation functional was used in this study. The band calculations revealed that the studied materials are indirect bandgap semiconductors, with bandgap energies of 2.67 and 2.28 eV for the undoped and F-doped B-Nb{sub 2}O{sub 5}, respectively. Upon doping B-Nb{sub 2}O{sub 5}, the Fermi level shifts towards the conduction band, allowing optical absorption in the visible region with enhanced transmittance in the wavelength range 400-1000 nm. The calculated static refractive index of the undoped B-Nb{sub 2}O{sub 5} is in good agreement with the reported experimental value, which is enhanced upon F-incorporation resulting in cladding properties for the F-doped B-Nb{sub 2}O{sub 5}. Also, the effective mass of free charge carriers increased upon F-doping. The enhanced properties were attributed to the effect of the excessive valent electron of the incorporated F atom. (orig.)

1/f noise in titanium doped aluminum thin film deposited by electron beam evaporation method and its dependence on structural variation with temperature

Science.gov (United States)

Ananda, P.; Vedanayakam, S. Victor; Thyagarajan, K.; Nandakumar, N.

2018-05-01

A brief review of Titanium doped Aluminum film has many attractive properties such as thermal properties and 1/f noise is highlighted. The thin film devices of Titanium doped alluminium are specially used in aerospace technology, automotive, biomedical fields also in microelectronics. In this paper, we discus on 1/f noise and nonlinear effects in titanium doped alluminium thin films deposited on glass substrate using electron beam evaporation for different current densities on varying temperatures of the film. The plots are dawn for 1/f noise of the films at different temperatures ranging from 300°C to 450°C and the slopes are determined. The studies shows a higher order increment in FFT amplitude of low frequency 1/f noise in thin films at annealing temperature 400°C. In this technology used in aerospace has been the major field of application of titanium doped alluminium, being one of the major challenges of the development of new alloys with improved strength at high temperature, wide chord Titanium doped alluminium fan blades increases the efficiency while reducing 1/f noise. Structural properties of XRD is identified.

NaF-assisted hydrothermal synthesis of Ti-doped hematite nanocubes with enhanced photoelectrochemical activity for water splitting

Energy Technology Data Exchange (ETDEWEB)

Zheng, Chong; Zhu, Zezhou; Wang, Sibo; Hou, Yidong, E-mail: ydhou@fzu.edu.cn

2015-12-30

Graphical abstract: An enhanced photoelectrochemical activity for water splitting was achieved over porous Ti-doped α-Fe{sub 2}O{sub 3} nanocubes. - Highlights: . • Ti-doped hematite nanocubes were successfully prepared by NaF-assisted hydrothermal deposition and subsequent annealing. • Ti-doped α-Fe{sub 2}O{sub 3} nanocubes showed an enhanced PEC activity with an IPCE of 25.2% at 340 nm at 1.23 V vs. RHE. • The enhanced activity of Ti-doped hematite nanocubes can be ascribed to high surface area and fast charge transportation. - Abstract: Ti-doped α-Fe{sub 2}O{sub 3} nanocubes on FTO substrate was prepared by hydrothermal deposition β-FeOOH onto FTO glass with a solution of FeCl{sub 3}, TiOCl{sub 2} and NaF, followed by an appropriate annealing. In comparison to Ti-doped α-Fe{sub 2}O{sub 3} nanorods Ti-doped α-Fe{sub 2}O{sub 3} nanocubes showed an enhanced photoelectrochemical activity for water splitting, with a remarkable IPCE of 25.2% at 340 nm at the potential of 1.23 V vs. RHE. The hematite films were studied in detail by X-ray diffraction, scanning electron microscopy, transmission electron microscopy, X-ray photoelectron spectroscopy, UV–vis absorption spectroscopy and electrochemical impedance spectroscopy. On the basis of the obtained results, the improved performance of Ti-doped α-Fe{sub 2}O{sub 3} nanocubes can be ascribed to the porous structure, good electrical conductivity and fast charge transportation of hematite.

The effect of the film thickness and doping content of SnO2:F thin films prepared by the ultrasonic spray method

International Nuclear Information System (INIS)

Rahal Achour; Benramache Said; Benhaoua Boubaker

2013-01-01

This paper reports on the effects of film thickness and doping content on the optical and electrical properties of fluorine-doped tin oxide. Tin (II) chloride dehydrate, ammonium fluoride dehydrate, ethanol and HCl were used as the starting materials, dopant source, solvent and stabilizer, respectively. The doped films were deposited on a glass substrate at different concentrations varying between 0 and 5 wt% using an ultrasonic spray technique. The SnO 2 :F thin films were deposited at a 350 °C pending time (5, 15, 60 and 90 s). The average transmission was about 80%, and the films were thus transparent in the visible region. The optical energy gap of the doped films with 2.5 wt% F was found to increase from 3.47 to 3.89 eV with increasing film thickness, and increased after doping at 5 wt%. The decrease in the Urbach energy of the SnO 2 :F thin films indicated a decrease in the defects. The increase in the electrical conductivity of the films reached maximum values of 278.9 and 281.9 (Ω·cm) −1 for 2.5 and 5 wt% F, respectively, indicating that the films exhibited an n-type semiconducting nature. A systematic study on the influence of film thickness and doping content on the properties of SnO 2 :F thin films deposited by ultrasonic spray was reported. (semiconductor materials)

Tribological evaluation of surface modified H13 tool steel in warm forming of Ti–6Al–4V titanium alloy sheet

Directory of Open Access Journals (Sweden)

Wang Dan

2014-08-01

Full Text Available The H13 hot-working tool steel is widely used as die material in the warm forming of Ti–6Al–4V titanium alloy sheet. However, under the heating condition, severe friction and lubricating conditions between the H13 tools and Ti–6Al–4V titanium alloy sheet would cause difficulty in guaranteeing forming quality. Surface modification may be used to control the level of friction force, reduce the friction wear and extend the service life of dies. In this paper, four surface modification methods (chromium plating, TiAlN coating, surface polishing and nitriding treatment were applied to the H13 surfaces. Taking the coefficient of friction (CoF and the wear degree as evaluation indicators, the high-temperature tribological behavior of the surface modified H13 steel was experimentally investigated under different tribological conditions. The results of this study indicate that the tribological properties of the TiAlN coating under dry friction condition are better than the others for a wide range of temperature (from room temperature to 500 °C, while there is little difference of tribological properties between different surface modifications under graphite lubricated condition, and the variation law of CoF with temperature under graphite lubricated is opposite to that under the dry friction.

Development of Stronger and More Reliable Cast Austenitic Stainless Steels (H-Series) Based on Scientific Design Methodology

Energy Technology Data Exchange (ETDEWEB)

Muralidharan, G.; Sikka, V.K.; Pankiw, R.I.

2006-04-15

The goal of this program was to increase the high-temperature strength of the H-Series of cast austenitic stainless steels by 50% and upper use temperature by 86 to 140 F (30 to 60 C). Meeting this goal is expected to result in energy savings of 38 trillion Btu/year by 2020 and energy cost savings of $185 million/year. The higher strength H-Series of cast stainless steels (HK and HP type) have applications for the production of ethylene in the chemical industry, for radiant burner tubes and transfer rolls for secondary processing of steel in the steel industry, and for many applications in the heat-treating industry. The project was led by Duraloy Technologies, Inc. with research participation by the Oak Ridge National Laboratory (ORNL) and industrial participation by a diverse group of companies. Energy Industries of Ohio (EIO) was also a partner in this project. Each team partner had well-defined roles. Duraloy Technologies led the team by identifying the base alloys that were to be improved from this research. Duraloy Technologies also provided an extensive creep data base on current alloys, provided creep-tested specimens of certain commercial alloys, and carried out centrifugal casting and component fabrication of newly designed alloys. Nucor Steel was the first partner company that installed the radiant burner tube assembly in their heat-treating furnace. Other steel companies participated in project review meetings and are currently working with Duraloy Technologies to obtain components of the new alloys. EIO is promoting the enhanced performance of the newly designed alloys to Ohio-based companies. The Timken Company is one of the Ohio companies being promoted by EIO. The project management and coordination plan is shown in Fig. 1.1. A related project at University of Texas-Arlington (UT-A) is described in Development of Semi-Stochastic Algorithm for Optimizing Alloy Composition of High-Temperature Austenitic Stainless Steels (H-Series) for Desired

Moessbauer study of LaFeAsO and F-doped superconductors in external magnetic fields

International Nuclear Information System (INIS)

Kitao, S; Kobayashi, Y; Higashitaniguchi, S; Kurokuzu, M; Saito, M; Seto, M; Mitsui, T; Kamihara, Y; Hirano, M; Hosono, H

2010-01-01

The iron-based F-doped superconductors LaFeAsO 1-x F x with a transition temperature of 24 K (for x = 0.07) and 26 K (x = 0.11) and its parent material LaFeAsO were studied using 57 Fe Moessbauer spectroscopy. Further investigation was carried out by applying external magnetic fields. F-doped superconductors showed a singlet pattern with no magnetic splitting throughout the temperature range from 4.2 to 298 K. On the other hand, magnetically-split spectra were observed in the parent LaFeAsO below the Neel temperature of about 140 K. The internal magnetic field reached 5.3 T at 4.2 K. The external magnetic fields up to 14 T were applied to the singlet phases, F-doped superconductors and the parent LaFeAsO above the Neel temperature. The induced magnetically-split spectra showed the internal magnetic fields with the comparable value to the applied fields. This fact confirmed that these singlet phases have the paramagnetic feature. The magnetic fields were also applied to the magnetically-ordered phase of LaFeAsO below the Neel temperature. The evolution of the spectra depending on the external magnetic fields was clearly explained by a model with two sublattice spins of the powdered antiferromagnet. This fact confirmed the magnetically-ordered phase is an antiferromagnet. The spin-flop field was also estimated by the model as about 26 T.

Lignocellulose-derived porous phosphorus-doped carbon as advanced electrode for supercapacitors

Science.gov (United States)

Yi, Jianan; Qing, Yan; Wu, ChuTian; Zeng, Yinxiang; Wu, Yiqiang; Lu, Xihong; Tong, Yexiang

2017-05-01

Engineering porous heteroatom-doped carbon nanomaterials with remarkable capacitive performance is highly attractive. Herein, a simple and smart method has been developed to synthesize phosphorus (P) doped carbon with hierarchical porous structure derived from lignocellulose. Hierarchically porous P doped carbon is readily obtained by the pyrolysis of lignocellulose immersed in ZnCl2/NaH2PO4 aqueous solution, and exhibits excellent capacitive properties. The as-obtained P doped porous carbon delivers a significant capacitance of 133 F g-1 (146 mF cm-2) at a high current density of 10 A g-1 with outstanding rate performance. Furthermore, the P doped carbon electrode yields a long-term cycling durability with more than 97.9% capacitance retention after 10000 cycles as well. A symmetric supercapacitor with a maximum energy density of 4.7 Wh kg-1 is also demonstrated based on these P doped carbon electrodes.

Thermal neutron imaging with rare-earth-ion-doped LiCaAlF{sub 6} scintillators and a sealed {sup 252}Cf source

Energy Technology Data Exchange (ETDEWEB)

Kawaguchi, Noriaki, E-mail: famicom@mail.tagen.tohoku.ac.jp [Tokuyama Corporation, Shibuya 3-chome, Shibuya-ku, Tokyo 150-8383 (Japan); IMRAM, Tohoku University, 2-1-1 Katahira, Aoba-ku, Sendai, Miyagi 980-8577 (Japan); Yanagida, Takayuki; Fujimoto, Yutaka; Yokota, Yuui; Kamada, Kei [IMRAM, Tohoku University, 2-1-1 Katahira, Aoba-ku, Sendai, Miyagi 980-8577 (Japan); Fukuda, Kentaro; Suyama, Toshihisa [Tokuyama Corporation, Shibuya 3-chome, Shibuya-ku, Tokyo 150-8383 (Japan); Watanabe, Kenichi; Yamazaki, Atsushi [Nagoya University, Furo-cho, Chikusa-ku, Nagoya 464-8603 (Japan); Chani, Valery [IMRAM, Tohoku University, 2-1-1 Katahira, Aoba-ku, Sendai, Miyagi 980-8577 (Japan); Yoshikawa, Akira [IMRAM, Tohoku University, 2-1-1 Katahira, Aoba-ku, Sendai, Miyagi 980-8577 (Japan); New Industry Creation Hatchery Center, Tohoku University, Sendai 980-8579 (Japan)

2011-10-01

Thermal neutron imaging with Ce-doped LiCaAlF{sub 6} crystals has been performed. The prototype of the neutron imager using a Ce-doped LiCaAlF{sub 6} scintillating crystal and a position sensitive photomultiplier tube (PSPMT) which had 64 multi-channel anode was developed. The Ce-doped LiCaAlF{sub 6} single crystal was grown by the Czochralski method. A plate with dimensions of a diameter of 50x2 mm{sup 2} was cut from the grown crystal, polished, and optically coupled to PSPMT by silicone grease. The {sup 252}Cf source (<1 MBq) was sealed with 43 mm of polyethylene for neutron thermalization. Alphabet-shaped Cd pieces with a thickness of 2 mm were used as a mask for the thermal neutrons. After corrections for the pedestals and gain of each pixel, we successfully obtained two-dimensional neutron images using Ce-doped LiCaAlF{sub 6}.

F/H Lab

Data.gov (United States)

Federal Laboratory Consortium — The F/H Laboratory is the largest of the eight laboratories within the SRS Analytical Area Project with over 100,000 square feet of floor space, 20,000 square foot...

Some physical properties of anhydrous and hydrated Brownmillerite doped with NaF

International Nuclear Information System (INIS)

Hassaan, M.Y.; El Desoky, M.M.; Salem, S.M.; Yousif, A.A.

2003-01-01

Different samples of Brownmillerite (the ferrite phase of cement clinker) doped with 0, 1 or 3 wt.% NaF were prepared. At first, the oxide mixture of Brownmillerite was prepared according to the following composition: 4 mol CaO, 1 mol Al 2 O 3 and 1 mol Fe 2 O 3 in addition to 1 or 3 wt.% NaF. Each mixture was mixed very well, introduced into an electric furnace at 1300 deg. C for 1 h in a platinum crucible, and then quenched in air. The product was divided into four portions mixed with 40 wt.% distilled water to form Brownmillerite paste, except for one portion which was left dry. Each paste was molded into two molds; after 24 h, they were immersed in a distilled water and withdrawn after 1 or 3 days of hydration, respectively. The pastes were ground again. The anhydrous powders of Brownmillerites and the hydrated samples were prepared for a.c. conduction measurements by pressing it to be in pellets form. The two surfaces of each pellet were coated with silver paste. The a.c. conductivity and dielectric constant for different samples were measured using four-probe method. The data was collected from 320 up to 670 K. Moessbauer spectra and X-ray diffraction patterns were measured for each sample (anhydrous and hydrated) to confirm the formation of Brownmillerite, identify the iron states and the magnetic properties. The results showed that NaF addition to Brownmillerite expedites the hydration reaction rate. The superparamagnetic relaxation, which appeared in the anhydrous Brownmillerite spectra due to the small particle size, decreases with increasing the hydration time. Also, the Fe 3+ (Oh) state increases while Fe 3+ (Td) decreases with the time of hydration. The a.c. conductivity value at fixed frequency for anhydrous and hydrated samples was found to increase with NaF addition. The a.c. conductivity and Moessbauer measurements can be used as good tools to verify the purity of Brownmillerite phase and, accordingly, the purity of cement

Spectral analysis of Pr{sup 3+} doped germanate glasses modified by BaO and BaF{sub 2}

Energy Technology Data Exchange (ETDEWEB)

Pisarska, Joanna, E-mail: joanna.pisarska@us.edu.pl [University of Silesia, Institute of Chemistry, Szkolna 9 Street, 40-007 Katowice (Poland); Pisarski, Wojciech A. [University of Silesia, Institute of Chemistry, Szkolna 9 Street, 40-007 Katowice (Poland); Dorosz, Dominik; Dorosz, Jan [Bialystok University of Technology, Faculty of Electrical Engineering, Wiejska 45D Street, 15-351 Bialystok (Poland)

2016-03-15

Luminescence properties of Pr{sup 3+} ions in germanate glasses modified by BaF{sub 2} were investigated. Several luminescence bands originating to transitions from the {sup 3}P{sub 0} state to the lower-lying states of Pr{sup 3+} were registered under 450 nm excitation. The spectral analysis suggests that the positions of luminescence bands and their relative intensities are changed significantly with BaF{sub 2} content. The relative integrated luminescence intensities of {sup 3}P{sub 0}→{sup 3}H{sub 4} transition (blue) to the {sup 3}P{sub 0}→{sup 3}F{sub 2} transition (red) of Pr{sup 3+} ions strongly depend on fluoride modifier BaF{sub 2} in glass composition. The luminescence bands of Pr{sup 3+} ions are shifted to shorter wavelengths with increasing BaF{sub 2} content. - Highlights: • Praseodymium doped lead-free germanate glasses modified by BaF{sub 2} were prepared. • Emission spectra correspond to transitions from {sup 3}P{sub 0} state to lower-lying states of Pr{sup 3+}. • The relative emission band intensities of Pr{sup 3+} depend strongly on BaF{sub 2} content. • Emission bands of Pr{sup 3+} are shifted to shorter wavelengths with increasing BaF{sub 2} content.

Corrosion of stainless steels in lead-bismuth eutectic up to 600 °C

Science.gov (United States)

Soler, L.; Martín, F. J.; Hernández, F.; Gómez-Briceño, D.

2004-11-01

An experimental program has been carried out to understand the differences in the corrosion behaviour between different stainless steels: the austenitic steels 304L and 316L, the martensitic steels F82Hmod, T91 and EM10, and the low alloy steel P22. The influence of oxygen level in Pb-Bi, temperature and exposure time is studied. At 600 °C, the martensitic steels and the P22 steel exhibit thick oxide scales that grow with time, following a linear law for the wet environment and a parabolic law for the dry one. The austenitic stainless steels show a better corrosion behaviour, especially AISI 304L. Under reducing conditions, the steels exhibit dissolution, more severe for the austenitic stainless steels. At 450 °C, all the materials show an acceptable behaviour provided a sufficient oxygen level in the Pb-Bi. At reducing conditions, the martensitic steels and the P22 steel have a good corrosion resistance, while the austenitic steels exhibit already dissolution at the longer exposures.

Corrosion of stainless steels in lead-bismuth eutectic up to 600 deg. C

International Nuclear Information System (INIS)

Soler, L.; Martin, F.J.; Hernandez, F.; Gomez-Briceno, D.

2004-01-01

An experimental program has been carried out to understand the differences in the corrosion behaviour between different stainless steels: the austenitic steels 304L and 316L, the martensitic steels F82Hmod, T91 and EM10, and the low alloy steel P22. The influence of oxygen level in Pb-Bi, temperature and exposure time is studied. At 600 deg. C, the martensitic steels and the P22 steel exhibit thick oxide scales that grow with time, following a linear law for the wet environment and a parabolic law for the dry one. The austenitic stainless steels show a better corrosion behaviour, especially AISI 304L. Under reducing conditions, the steels exhibit dissolution, more severe for the austenitic stainless steels. At 450 deg. C, all the materials show an acceptable behaviour provided a sufficient oxygen level in the Pb-Bi. At reducing conditions, the martensitic steels and the P22 steel have a good corrosion resistance, while the austenitic steels exhibit already dissolution at the longer exposures

Destabilized LiBH4-NaAlH4 Mixtures Doped with Titanium Based Catalysts

DEFF Research Database (Denmark)

Shi, Qing; Yu, Xuebin; Feidenhans'l, Robert

2008-01-01

We investigate the hydrogen storage properties of the mixed complex hydride LiBH4-NaAlH4 system, both undoped and doped with a TiCl3 additive. The mixed system is found to initiate a transformation to LiBH4-NaAlH4 after ball-milling, and the doped system is found to have a significant lower hydro...

Reduced-pressure chemical vapor deposition of boron-doped Si and Ge layers

International Nuclear Information System (INIS)

Bogumilowicz, Y.; Hartmann, J.M.

2014-01-01

We have studied the in-situ boron (B) doping of germanium (Ge) and silicon (Si) in Reduced Pressure-Chemical Vapor Deposition. Three growth temperatures have been investigated for the B-doping of Ge: 400, 600 and 750 °C at a constant growth pressure of 13300 Pa (i.e. 100 Torr). The B concentration in the Ge:B epilayer increases linearly with the diborane concentration in the gaseous phase. Single-crystalline Ge:B layers with B concentrations in-between 9 ∙ 10 17 and 1 ∙ 10 20 cm −3 were achieved. For the in-situ B doping of Si at 850 °C, two dichlorosilane mass flow ratios (MFR) have been assessed: F[SiH 2 Cl 2 ]/F[H 2 ] = 0.0025 and F[SiH 2 Cl 2 ]/F[H 2 ] = 0.0113 at a growth pressure of 2660 Pa (i.e. 20 Torr). Linear boron incorporation with the diborane concentration in the gas phase has been observed and doping levels in-between 3.5 ∙ 10 17 and 1 ∙ 10 20 cm −3 were achieved. We almost kept the same ratio of B versus Si atoms in the gas phase and in the Si epilayer. By contrast, roughly half of the B atoms present in the gas phase were incorporated in the Ge:B layers irrespective of the growth temperature. X-Ray Diffraction (XRD) allowed us to extract from the angular position of the Ge:B layer diffraction peak the substitutional B concentration. Values close to the B concentrations obtained by 4-probe resistivity measurements were obtained. Ge:B layers were smooth (< 1 m root mean square roughness associated with 20 × 20 μm 2 Atomic Force Microscopy images). Only for high F[B 2 H 6 ]/F[GeH 4 ] MFR (3.2 10 −3 ) did the Ge:B layers became rough; they were however still mono-crystalline (XRD). Above this MFR value, Ge:B layers became polycrystalline. - Highlights: • Boron doping of germanium and silicon in Reduced Pressure-Chemical Vapor Deposition • Linear boron incorporation in Ge:B and Si:B with the diborane flow • Single-crystal Ge:B layers with B concentrations in-between 9 ∙ 10 17 and 1 ∙ 10 20 cm −3 • Single-crystal Si

A comparative study on the flux pinning properties of Zr-doped YBCO film with those of Sn-doped one prepared by metal-organic deposition

International Nuclear Information System (INIS)

Choi, S. M.; Shin, G. M.; Joo, Y.S.; Yoo, S. I.

2013-01-01

We investigated the flux pinning properties of both 10 mol% Zr-and Sn-doped YBa 2 Cu 3 O 7-δ (YBCO) films with the same thickness of ∽350 nm for a comparative purpose. The films were prepared on the SrTiO 3 (STO) single crystal substrate by the metal-organic deposition (MOD) process. Compared with Sn-doped YBCO film, Zr-doped one exhibited a significant enhancement in the critical current density (J c ) and pinning force density (F p ). The anisotropic J c ,min/J c ,max ratio in the field-angle dependence of J c at 77 K for 1 T was also improved from 0.23 for Sn-doped YBCO to 0.39 for Zr-doped YBCO. Thus, the highest magnetic J c values of 9.0 and 2.9 MA/cm 2 with the maximum F p (F p ,max) values of 19 and 5 GN/m 3 at 65 and 77 K for H // c, respectively, could be achieved from Zr-doped YBCO film. The stronger pinning effect in Zr-doped YBCO film is attributable to smaller BaZrO-3 (BZO) nanoparticles (the average size ≈ 28.4 nm) than YBa 2 SnO 5. 5 (YBSO) nanoparticles (the average size ≈ 45.0 nm) incorporated in Sn-doped YBCO film since smaller nanoparticles can generate more defects acting as effective flux pinning sites due to larger incoherent interfacial area for the same doping concentration.

Ce decay curves in Ce, Tb co-doped LaF3 and the energy transfer mechanism

International Nuclear Information System (INIS)

Kroon, R.E.; Swart, H.C.; Ntwaeaborwa, O.M.; Seed Ahmed, H.A.A.

2014-01-01

Energy transfer phenomena can play an important role in the development of luminescent materials, and hosts co-doped with Ce 3+ and Tb 3+ ions continue to be actively studied. Several recent reports on Ce, Tb co-doped phosphors suggest different mechanisms for the energy transfer from Ce 3+ to Tb 3+ ions and further study is required to reach consensus on the mechanism or to understand why different mechanisms dominate in different hosts. A more direct method of analysis is proposed to distinguish between the different types of multipole energy transfer mechanisms. When applied to Ce, Tb co-doped LaF 3 , the experimental data shows a poor match to any of these models but is consistent with energy transfer through the exchange mechanism. The decay curves of Ce emission in Ce, Tb co-doped LaF 3 were also studied to obtain further insight on the energy transfer mechanism. Although the decrease in lifetime with increasing Tb concentration shows that energy transfer occurs through a non-radiative mechanism, the form of the decay curves does not correspond to what is expected for energy transfer via multipole interactions.

Surface studies on benzophenone doped PDMS microstructures fabricated using KrF excimer laser direct write lithography

International Nuclear Information System (INIS)

Kant, Madhushree Bute; Shinde, Shashikant D.; Bodas, Dhananjay; Patil, K.R.; Sathe, V.G.; Adhi, K.P.; Gosavi, S.W.

2014-01-01

Graphical abstract: - Highlights: • Use of KrF Laser micromachining for Lab-On-Chip applications at lower fluence. • Addition of Benzophenone in PDMS enhances its self development sensitivity. • Benzophenone helps efficient energy transfer for equal density of bond scissioning. • Correlation of chemical composition with laser dose and microstructure. • Microstructures with well defined clean sidewalls. - Abstract: This paper discusses microfabrication process for benzophenone doped polydimethylsiloxane (PDMS) using laser lithography. KrF excimer laser of 248 nm with 20 ns pulse width at repetition rate of 1 Hz was used for microfabrication of undoped and benzophenone doped PDMS. The doped-PDMS shows sensitivity below 365 nm, permitting processing under ambient light. The analysis of etch depth revealed that doped PDMS shows self developable sensitivity at lower fluence of ∼250 mJ/cm 2 . The unexposed and exposed surface was studied using Fourier transform infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS), Raman spectroscopy and Scanning electron microscopy (SEM). Spectrocopic analysis indicated increase in C-O, C=O, Si-O 3 and Si-O 4 bonding at the expense of Si-C and Si-O 2 bonds of PDMS. In case of laser exposed doped-PDMS, removal of benzophenone from probe depth of spectroscopy was observed. Whereas the surface morphology of exposed and unexposed doped-PDMS was observed to be same, indicating clean development of PDMS micropatterns. The present study indicates that addition of 3.0 wt.% benzophenone in PDMS enhance self development sensitivity of PDMS. The self developable results on doped-PDMS are quite encouraging for its potential use in point of care Lab-On-Chip applications, for fabricating micropatterns using direct write laser lithography technology

Thermo-mechanical fatigue behavior of reduced activation ferrite/martensite stainless steels

International Nuclear Information System (INIS)

Petersen, C.; Rodrian, D.

2002-01-01

The thermo-mechanical cycling fatigue (TMCF) behavior of reduced activation ferrite/martensite stainless steels is examined. The test rig consists of a stiff load frame, which is directly heated by the digitally controlled ohmic heating device. Cylindrical specimens are used with a wall thickness of 0.4 mm. Variable strain rates are applied at TMCF test mode, due to the constant heating rate of 5.8 K/s and variable temperature changes. TMCF results of as received EUROFER 97 in the temperature range between 100 and 500-600 deg. C show a reduction in life time (a factor of 2) compared to F82H mod. and OPTIFER IV. TMCF-experiments with hold times of 100 and 1000 s show dramatic reduction in life time for all three materials

Temperature dependence of the ultraviolet luminescence of Pr3+-doped 20Al(PO3)3-80LiF glass scintillator

International Nuclear Information System (INIS)

Tsuboi, Mizuki; Takeda, Kohei; Nakazato, Tomoharu

2017-01-01

The development of scintillator materials for scattered neutrons is essential in studying laser fusion experiments. We have previously investigated and proposed Pr 3+ -doped 20Al(PO 3 ) 3 -80LiF (APLF + Pr) glasses as scintillators for neutron detection. The APLF + Pr glass emissions are then investigated with synchrotron radiation excitation and varying sample temperature. APLF + Pr glasses exhibit luminescence emission located at 200 to 300 nm and 400 nm attributed to the 4f5d → 4f 2 and 4f 2 → 4f 2 ( 1 S 0 → 3 P j + 1 I 6 ) transitions, respectively. In addition, the 200 to 300-nm emission is not substantially affected by temperature, while the 400-nm emission intensities increase with decreasing sample temperature. This temperature dependence is attributed to cross relaxation whose effect can be controlled by the Pr-doping concentration. Our results suggest that doping concentration of APLF + Pr must be optimized and that APLF + Pr glasses must operate a low temperatures for better neutron detection. (author)

Eu and Rb co-doped LiCaAlF6 scintillators for neutron detection

International Nuclear Information System (INIS)

Yamaji, Akihiro; Yanagida, Takayuki; Kawaguchi, Noriaki; Yokota, Yuui; Fujimoto, Yutaka; Kurosawa, Shunsuke; Pejchal, Jan; Watanabe, Kenichi; Yamazaki, Atsushi; Yoshikawa, Akira

2013-01-01

Eu and Rb co-doped LiCaAlF 6 (LiCAF) single crystals with different dopant concentrations were grown by the micro-pulling-down method for neutron detection. Their transmittance spectra showed strong absorption bands at 200–220 and 290–350 nm, and under 241 Am alpha-ray excitation, their radioluminescence spectra exhibited an intense emission peak at 373 nm that was attributed to the Eu 2+ 5d–4f transition. These results were consistent with those for the Rb-free Eu:LiCAF. The highest light yield among the grown crystals was 36,000 ph/n, which was 20% greater than that of the Rb-free crystal. In addition, the neutron-excited scintillation decay times were 650–750 ns slower than that of the Rb-free Eu:LiCAF. -- Highlights: •Eu and Rb co-doped LiCaAlF 6 crystals were grown by the micro-pulling down method. •Transmittance, photoluminescence and radioluminescence spectra were measured. •The light yields and scintillation decays were evaluated under 252 Cf neutron irradiation

Antibacterial properties of F-doped ZnO visible light photocatalyst

Energy Technology Data Exchange (ETDEWEB)

Podporska-Carroll, Joanna, E-mail: joannapcarroll@gmail.com [Center for Research in Engineering Surface Technology (CREST), DIT FOCAS Institute, Kevin St., Dublin (Ireland); Myles, Adam [Center for Research in Engineering Surface Technology (CREST), DIT FOCAS Institute, Kevin St., Dublin (Ireland); School of Chemical and Pharmaceutical Sciences, Dublin Institute of Technology, Kevin St., Dublin (Ireland); Quilty, Brid [School of Biotechnology, Dublin City University, Dublin (Ireland); McCormack, Declan E.; Fagan, Rachel [Center for Research in Engineering Surface Technology (CREST), DIT FOCAS Institute, Kevin St., Dublin (Ireland); School of Chemical and Pharmaceutical Sciences, Dublin Institute of Technology, Kevin St., Dublin (Ireland); Hinder, Steven J. [The Surface Analysis Laboratory, Faculty of Engineering and Physical Sciences, University of Surrey, Guildford, Surrey GU2 7XH (United Kingdom); Dionysiou, Dionysios D., E-mail: dionysios.d.dionysiou@uc.edu [Environmental Engineering and Science Program, Department of Biomedical, Chemical and Environmental Engineering (DBCEE), 705 Engineering Research Center, University of Cincinnati, Cincinnati, OH 45221-0012 (United States); Pillai, Suresh C., E-mail: Pillai.Suresh@itsligo.ie [Center for Research in Engineering Surface Technology (CREST), DIT FOCAS Institute, Kevin St., Dublin (Ireland); Nanotechnology Research Group, Department of Environmental Science, PEM Centre, Institute of Technology Sligo, Sligo (Ireland)

2017-02-15

Highlights: • F doped ZnO nano-powders were obtained by a modified sol–gel method. • These materials were found to be effective against S. aureus and E. coli. • Enhanced visible light photocatalytic and antimicrobial properties were obtained. • The toxic effect of ZnO on bacteria can be due to the release of zinc cations. • Production of reactive oxidation species influences bacterial viability. - Abstract: Nanocrystalline ZnO photocatalysts were prepared by a sol–gel method and modified with fluorine to improve their photocatalytic anti-bacterial activity in visible light. Pathogenic bacteria such as Escherichia coli (Gram-negative) and Staphylococcus aureus (Gram-positive) were employed to evaluate the antimicrobial properties of synthesized materials. The interaction with biological systems was assessed by analysis of the antibacterial properties of bacteria suspended in 2% (w/w) powder solutions. The F-doping was found to be effective against S. aureus (99.99% antibacterial activity) and E. coli (99.87% antibacterial activity) when irradiated with visible light. Production of reactive oxygen species is one of the major factors that negatively impact bacterial growth. In addition, the nanosize of the ZnO particles can also be toxic to microorganisms. The small size and high surface-to-volume ratio of the ZnO nanoparticles are believed to play a role in enhancing antimicrobial activity.

Micro-Abrasion Wear Resistance of Borided 316L Stainless Steel and AISI 1018 Steel

Science.gov (United States)

Reséndiz-Calderon, C. D.; Rodríguez-Castro, G. A.; Meneses-Amador, A.; Campos-Silva, I. E.; Andraca-Adame, J.; Palomar-Pardavé, M. E.; Gallardo-Hernández, E. A.

2017-11-01

The 316L stainless steel has high corrosion resistance but low tribological performance. In different industrial sectors (biomedical, chemical, petrochemical, and nuclear engineering), improvement upon wear resistance of 316L stainless steel components using accessible and inexpensive methods is critical. The AISI 1018 steel is widely used in industry, but its tribological performance is not the best among steels. Therefore, in this study the behavior of the borided 316L stainless steel and 1018 steel is evaluated under micro-abrasion wear. The boriding was carried out at 1223 K over 6 h of exposure time, resulting in a biphase layer composed of FeB/Fe2B phases. In order to evaluate Fe2B phase with no influence from FeB phase, AISI 1018 steel samples were borided at 1273 K for over 20 min and then diffusion annealed at 1273 K over 2 h to obtain a Fe2B mono-phase layer. Micro-abrasion wear resistance was evaluated by a commercial micro-abrasion testing rig using a mix of F-1200 SiC particles with deionized water as abrasive slurry. The obtained wear rates for FeB and Fe2B phases and for the 316L stainless steel were compared. Wear resistance of 316L stainless steel increases after boriding. The wear mechanisms for both phases and for the stainless steel were identified. Also, transient conditions for rolling and grooving abrasion were determined for the FeB and Fe2B phases.

Synergistic effects of Mo and F doping on the quality factor of ZnO thin films prepared by a fully automated home-made nebulizer spray technique

Science.gov (United States)

Ravichandran, K.; Dineshbabu, N.; Arun, T.; Manivasaham, A.; Sindhuja, E.

2017-01-01

Transparent conducting oxide films of undoped, Mo doped, Mo + F co-doped ZnO were deposited using a facile homemade nebulizer spray pyrolysis technique. The effects of Mo and F doping on the structural, optical, electrical and surface morphological properties were investigated using XRD, UV-vis-NIR spectroscopy, I-V and Hall probe techniques, FESEM and AFM, and XPS, respectively. The XRD analysis confirms that all the films are well crystallized with hexagonal wurtzite structure. All the synthesized samples exhibit high transmittance (above 85%) in the visible region. The current-voltage (I-V) characteristics show the ohmic conduction nature of the films. The Hall probe measurements show that the synergistic effects of Mo and F doping cause desirable improvements in the quality factor of the ZnO films. A minimum resistivity of 5.12 × 10-3 Ω cm with remarkably higher values of mobility and carrier concentration is achieved for Mo (2 at.%) + F (15 at.%) co-doped ZnO films. A considerable variation in the intensity of deep level emission caused by Mo and F doping is observed in the photoluminescence (PL) studies. The presence of the constituent elements in the samples is confirmed by XPS analysis.

Superconductivity and magnetism in Ir-doped GdFeAsO

International Nuclear Information System (INIS)

Cui, Y.J.; Chen, Y.L.; Cheng, C.H.; Yang, Y.; Jiang, J.; Wang, Y.Z.; Zhang, Y.; Zhao, Y.

2010-01-01

The 5d-transition metal, Ir has successfully been doped at Fe site and induced superconductivity in GdFeAsO at T c = 18.9 K and ∼20 atom%. The Ir-doping shortened the c-axis length and stretched the a-axis one, which led to enhance the coupling between the FeAs- and SmO-layer, and to weaken the bonding between Fe and As atom. Paramagnetism was observed in all of the samples, which was resulted from the magnetic Gd ion as in the F-doped GdFeAsO. An upper critical field of GdFe 0.8 Ir 0.2 AsO was extrapolated to around 24 T, much smaller than that of F-doped GdFeAsO owing to a relatively low T c and small value of dH c2 /dT.

A first-principles study on the magnetic properties of nonmetal atom doped phosphorene monolayers.

Science.gov (United States)

Zheng, Huiling; Zhang, Jianmin; Yang, Baishun; Du, Xiaobo; Yan, Yu

2015-07-07

In order to induce magnetism in two-dimensional semiconductors for their applications in spintronic devices and novel chemical and electronic properties of semiconducting phosphorene, the geometrical structure, electronic and magnetic properties of doped phosphorene monolayers with a series of nonmetal atoms, including H, F, Cl, Br, I, B, C, Si, N, As, O, S and Se, were systematically investigated using first-principles calculations. The results show that although the substitutional doping of H, F, Cl, Br, I, B, N, O, S or Se results in large structural deformation at the doping sites of phosphorene monolayers, all neutral nonmetal atom doped systems are stable. The calculated formation energies reveal that the substitutional doping of numerous nonmetal atoms in phosphorene monolayer are possible under appropriate experimental conditions, and the charged dopants C(-), Si(-), S(+) and Se(+) are stable. Moreover, the substitutional doping of H, F, Cl, Br, I, B, N, As, C(-), Si(-), S(+) or Se(+) cannot induce magnetism in phosphorene monolayer due to the saturation or pairing of valence electrons of dopant and its neighboring P atoms, whereas ground states of neutral C, Si, O, S or Se doped systems are magnetic due to the appearance of an unpaired valence electron of C and Si or the formation of a nonbonding 3p electron of a neighboring P atom around O, S and Se. Furthermore, the magnetic coupling between the moments induced by two Si, O, S or Se are long-range anti-ferromagnetic and the coupling can be attributed to the hybridization interaction involving polarized electrons, whereas the coupling between the moments induced by two C is weak.

Gas Sensing of Fluorine Doped Tin Oxide Thin Films Prepared by Spray Pyrolysis

Directory of Open Access Journals (Sweden)

A. A. YADAV

2008-05-01

Full Text Available Fluorine doped tin oxide (F: SnO2 films have been prepared onto the amorphous glass substrates by a spray pyrolysis. XRD studies reveal that the material deposited is polycrystalline SnO2 and have tetragonal structure. It is observed that films are highly orientated along (200 direction. The direct optical band gap energy for the F: SnO2 films are found to be 4.15 eV. Gas sensing properties of the sensor were checked against combustible gases like H2, CO2 CO, C3H8, CH4.The H2 sensitivity of the F-doped SnO2 sensor was found to be increased. The increase in the sensitivity is discussed in terms of increased resistivity and reduced permeation of gaseous oxygen into the underlying sensing layer due to the surface modification of the sensor.

Development of transparent conductive indium and fluorine co-doped ZnO thin films: Effect of F concentration and post-annealing temperature

Energy Technology Data Exchange (ETDEWEB)

Hadri, A. [University Mohammed V, Faculty of Sciences, Physics Department, LPM, B.P. 1014, Rabat (Morocco); Taibi, M. [University of Mohammed V, LPCMIN, Ecole Normale Superieure, Rabat (Morocco); Loghmarti, M.; Nassiri, C.; Slimani Tlemçani, T. [University Mohammed V, Faculty of Sciences, Physics Department, LPM, B.P. 1014, Rabat (Morocco); Mzerd, A., E-mail: mzerd@yahoo.fr [University Mohammed V, Faculty of Sciences, Physics Department, LPM, B.P. 1014, Rabat (Morocco)

2016-02-29

In the present work ZnO, In doped ZnO and In-F co-doped ZnO (IFZO) films were synthesized on heated glass substrates (350 °C) by the chemical spray technique. The effect of fluorine concentration on the structural, morphological, optical and electrical properties was studied. It was observed from X-ray diffraction (XRD) that the films have a polycrystalline structure and the intensity of the peaks depend on the doping and co-doping concentration. No diffraction peak related to dopants in XRD patterns along with shift in peaks angles to ZnO proved that In and F ions were doped into ZnO thin films. The Raman spectra confirm the hexagonal structure of the as-deposited films, and demonstrated an enhancement of the surface phonon mode of doped and co-doped films as compared to undoped films. The as-deposited films showed an average transmittance above 70%, in the wavelength range of 400–800 nm. A minimum electrical resistivity, in the order of 5.2 × 10{sup −} {sup 2} Ω cm was obtained for the IFZO thin film with 5 at.% F doping. Moreover, the electrical properties of doped and co-doped films were enhanced after post-deposition annealing. It was found that post-annealed thin films at 350 °C showed a decrease of one order of magnitude of the resistivity values. Such a transparent and conducting thin film can be suitable for optical and electrical applications owing to their low resistivity combined with high transmittance in the visible range. - Highlights: • Conductive transparent ZnO, IZO, IFZO thin films were deposited by spray pyrolysis. • Doping and co-doping affect morphology and optoelectrical properties. • As deposited film with high fluorine content exhibited high carrier mobility (55 cm{sup 2} V{sup −} {sup 1} s{sup −} {sup 1}). • Correlation between intrinsic defects and carrier mobility was observed. • Post-annealing in Ar atmosphere improves conductivity.

Surface studies on benzophenone doped PDMS microstructures fabricated using KrF excimer laser direct write lithography

Energy Technology Data Exchange (ETDEWEB)

Kant, Madhushree Bute; Shinde, Shashikant D. [Department of Physics, University of Pune, Pune 411007 (India); Bodas, Dhananjay [Centre for Nanobioscience, Agharkar Research Institute, Agharkar road, Pune 411004 (India); Patil, K.R. [Center for Materials Characterization, National Chemical Laboratories, Pune 411008 (India); Sathe, V.G. [UGC DAE Inter University Consortium, Indore 452017 (India); Adhi, K.P. [Department of Physics, University of Pune, Pune 411007 (India); Gosavi, S.W., E-mail: swg@physics.unipune.ac.in [Department of Physics, University of Pune, Pune 411007 (India)

2014-09-30

Graphical abstract: - Highlights: • Use of KrF Laser micromachining for Lab-On-Chip applications at lower fluence. • Addition of Benzophenone in PDMS enhances its self development sensitivity. • Benzophenone helps efficient energy transfer for equal density of bond scissioning. • Correlation of chemical composition with laser dose and microstructure. • Microstructures with well defined clean sidewalls. - Abstract: This paper discusses microfabrication process for benzophenone doped polydimethylsiloxane (PDMS) using laser lithography. KrF excimer laser of 248 nm with 20 ns pulse width at repetition rate of 1 Hz was used for microfabrication of undoped and benzophenone doped PDMS. The doped-PDMS shows sensitivity below 365 nm, permitting processing under ambient light. The analysis of etch depth revealed that doped PDMS shows self developable sensitivity at lower fluence of ∼250 mJ/cm{sup 2}. The unexposed and exposed surface was studied using Fourier transform infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS), Raman spectroscopy and Scanning electron microscopy (SEM). Spectrocopic analysis indicated increase in C-O, C=O, Si-O{sub 3} and Si-O{sub 4} bonding at the expense of Si-C and Si-O{sub 2} bonds of PDMS. In case of laser exposed doped-PDMS, removal of benzophenone from probe depth of spectroscopy was observed. Whereas the surface morphology of exposed and unexposed doped-PDMS was observed to be same, indicating clean development of PDMS micropatterns. The present study indicates that addition of 3.0 wt.% benzophenone in PDMS enhance self development sensitivity of PDMS. The self developable results on doped-PDMS are quite encouraging for its potential use in point of care Lab-On-Chip applications, for fabricating micropatterns using direct write laser lithography technology.

Surface chemical and photocatalytic consequences of Ca-doping of BiFeO{sub 3} as probed by XPS and H{sub 2}O{sub 2} decomposition studies

Energy Technology Data Exchange (ETDEWEB)

Zaki, Mohamed I., E-mail: mizaki@link.net [Chemistry Department, Faculty of Science, Minia University, El-Minia 61519 (Egypt); Ramadan, Wegdan [Physics Department, Faculty of Science, Alexandria University, Alexandria 21511 (Egypt); Katrib, Ali [Chemistry Department, Faculty of Science, Kuwait University, P.O. Box 5969, Safat 13060 (Kuwait); Rabee, Abdallah I.M. [Chemistry Department, Faculty of Science, Minia University, El-Minia 61519 (Egypt)

2014-10-30

Graphical abstract: - Highlights: • BiFeO{sub 3} is a modest visible-light heterogeneous photocatalyst for H{sub 2}O{sub 2} decomposition. • The ferrite activity is promoted with Ca-doping up to 10 wt%-Ca. • Favourable consequences are enhanced surface metal redoxability and oxide basicity. • Furthering doping to >10 wt%-Ca retrogresses the ferrite photocatalytic activity. • A retrogressive doping consequence is bulk phase separation of α(γ)-Fe{sub 2}O{sub 3}. - Abstract: Pure and Ca-doped Bi{sub 1−x}Ca{sub x}FeO{sub 3} samples were prepared with x = 0.0–0.2, adopting a sol–gel method. Previously reported studies performed on similarly composed and prepared samples revealed that Ca-doping, above solubility limit (namely at ≥10%-Ca), results in phase separation and formation of BiFeO{sub 3}/α(γ)-Fe{sub 2}O{sub 3} nanocomposite particles. Hetero p/n nanojunctions thus established were considered to help separating photo-generated electron–hole pairs and, therefore, explain consequent promotion of photo-Fenton catalytic activity of BiFeO{sub 3} towards methylene blue degradation in presence of H{sub 2}O{sub 2} additive. However, the encompassed decomposition of H{sub 2}O{sub 2} was not addressed. To bridge this gap of knowledge, the present investigation was designed to assess Ca-doping-effected surface chemical modifications and gauge its impact on the heterogeneous photo-/thermo-catalytic activity of BiFeO{sub 3} towards H{sub 2}O{sub 2} decomposition, by means of X-ray photoelectron spectroscopy (XPS) and H{sub 2}O{sub 2} decomposition gravimetry. XPS results revealed generation of high binding energy Bi 4f and Fe 2p states, as well as enhancement of the surface basicity, upon doping to 10%-Ca. These surface chemical consequences are rendered hardly detectable upon further increase of the dopant magnitude to 20%-Ca. In parallel, the H{sub 2}O{sub 2} decomposition activity of the ferrite, under natural visible light, is enhanced to optimize

Mechanism of improvement on strength and toughness of H13 die steel by nitrogen

International Nuclear Information System (INIS)

Li, Jing-Yuan; Chen, Yu-Lai; Huo, Jian-Hua

2015-01-01

The mechanism of nitrogen addition to AISI H13 die steel is proposed and supported using thermodynamic calculations in addition to observed changes in precipitate, microstructure, crystal structure, and macroproperties. The results indicate that the average impact toughness ak of the novel nitrogen H13 steel is maximally 17.6 J cm −2 and minimally 13.4 J cm −2 . These values result in die steel that reaches premium grade and approximate the superior grade as specified in NADCA#207-2003, additionally the hardness is improved 3–5HRC. Experimental findings indicate that the residual V(C,N) particles undissolved during nitrogen H13 steel austenitizing by quenching helps to suppress growth of original austenitic crystal grains, this in turn results in finer martensitic structures after quenching. In the subsequent tempering process all N atoms are dissolved in the solid state matrix a result of C atoms displacing N atoms in V(C,N). Solid dissolution of N atoms produces a distorted lattice of Fe matrix which results in an increase in the hardness of the steel. Additionally this displacement reaction is important for slow growth of secondary particles in nitrogen H13 steel during the tempering process which helps to increase impact toughness compared to its nitrogen-free counterpart given the same condition of heat-treatment

Crystal growth and scintillation properties of Ce and Eu doped LiSrAlF{sub 6}

Energy Technology Data Exchange (ETDEWEB)

Yamaji, Akihiro, E-mail: yamaji-a@imr.tohoku.ac.jp [Institute of Materials Research, Tohoku University, 2-1-1 Katahira, Aoba-ku, Sendai 980-8577 (Japan); Yanagida, Takayuki [New Industry Creation Hatchery Center (NICHe), Tohoku University, 6-6-10 Aoba, Aramaki, Aoba-ku, Sendai 980-8579 (Japan); Kawaguchi, Noriaki [Tokuyama Corporation, Shibuya 3-chome, Shibuya, Tokyo 150-8383 (Japan); Fujimoto, Yutaka; Yokota, Yuui [Institute of Materials Research, Tohoku University, 2-1-1 Katahira, Aoba-ku, Sendai 980-8577 (Japan); Watanabe, Kenichi; Yamazaki, Atsushi [Department of Material, Physics and Energy Engineering, Nagoya University, Furo-cho, Chikusa-ku, Nagoya, 464-8603 (Japan); Yoshikawa, Akira [Institute of Materials Research, Tohoku University, 2-1-1 Katahira, Aoba-ku, Sendai 980-8577 (Japan); New Industry Creation Hatchery Center (NICHe), Tohoku University, 6-6-10 Aoba, Aramaki, Aoba-ku, Sendai 980-8579 (Japan); Pejchal, Jan [Institute of Physics AS CR, Cukrovarnicka 10, 16200 Prague 6 (Czech Republic)

2011-12-11

Ce and Eu doped LiSrAlF{sub 6} (LiSAF) single crystals for the neutron detection with different dopant concentrations were grown by the micro-pulling-down method ({mu}-PD). In Ce:LiSAF, intense emission peaks due to Ce{sup 3+} 5d-4f transitions were observed at approximately 315 and 335 nm in photo- and {alpha}-ray induced radio-luminescence spectra. In case of Eu:LiSAFs, an intense emission peak at 375 nm due to Eu{sup 2+} 5d-4f transition was observed in the radio-luminescence spectra. The pulse height spectra and decay time profiles were measured under {sup 252}Cf neutron irradiation to examine the neutron response. The Ce 3% and Eu 2% doped LiSAF showed the highest light yield of 2860 ph/n with 19 ns main decay time component and 24,000 ph/n with 1610 ns.

A facile method to synthesize nitrogen and fluorine co-doped TiO{sub 2} nanoparticles by pyrolysis of (NH{sub 4}){sub 2}TiF{sub 6}

Energy Technology Data Exchange (ETDEWEB)

Chen Daimei; Jiang Zhongyi; Geng Jiaqing; Zhu Juhong; Yang Dong, E-mail: dyangdong@hotmail.co [Tianjin University, Key Laboratory for Green Chemical Technology, School of Chemical Engineering and Technology (China)

2009-02-15

The nitrogen and fluorine co-doped TiO{sub 2} (N-F-TiO{sub 2}) nanoparticles of anatase crystalline structure were prepared by a facile method of (NH{sub 4}){sub 2}TiF{sub 6} pyrolysis, and characterized by thermogravimetry-differential thermal analysis (TG-DTA), X-ray diffraction (XRD), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), and ultraviolet visible (UV-Vis) spectroscopy etc. With the increase of calcination temperature, (NH{sub 4}){sub 2}TiF{sub 6} decomposed into TiOF{sub 2} and NH{sub 4}TiOF{sub 3} at first, and then formed anatase-type TiO{sub 2} with thin sheet morphology. H{sub 3}BO{sub 3} as oxygen source can promote the formation of anatase TiO{sub 2}, but decrease the F content in the N-F-TiO{sub 2} materials due to the formation of volatile BF{sub 3} during the precursor decomposition. The photocatalytic activity of the obtained N-F-TiO{sub 2} samples was evaluated by the methylene blue degradation under visible light, and all the samples exhibited much higher photocatalytic activity than P25. Moreover, the merits and disadvantages of this proposed method to prepare doped TiO{sub 2} are discussed.

Cubic to tetragonal phase transition of Tm3+ doped nanocrystals in oxyfluoride glass ceramics

International Nuclear Information System (INIS)

Li, Yiming; Fu, Yuting; Shi, Yahui; Zhang, Xiaoyu; Yu, Hua; Zhao, Lijuan

2016-01-01

Tm 3+ ions doped β-PbF 2 nanocrystals in oxyfluoride glass ceramics with different doping concentrations and thermal temperatures are prepared by a traditional melt-quenching and thermal treatment method to investigate the structure and the phase transition of Tm 3+ doped nanocrystals. The structures are characterized by X-ray diffraction Rietveld analysis and confirmed with numerical simulation. The phase transitions are proved further by the emission spectra. Both of the doping concentration and thermal temperature can induce an O h to D 4h site symmetry distortion and a cubic to tetragonal phase transition. The luminescence of Tm 3+ doped nanocrystals at 800 nm was modulated by the phase transition of the surrounding crystal field

Zirconium coatings doped with nanoparticles for the protection of stainless steel

International Nuclear Information System (INIS)

Pineda, F; Vargas, E; Martinez, C; Sancy, M; Rabagliati, F.M; Pavez, J; Paez, M.A

2008-01-01

The anticorrosive protection of metal alloys, like stainless steel, is usually carried out with chrome-based coatings, but the toxic wastes associated with the process minimizes its applicability. The above has motivated the search for alternative protection methodologies, among which are the inorganic polymers prepared by the sol-gel method, which are a viable protection alternative because of their outstanding chemical and physical properties in aggressive environments. Despite the method's benefits, the application of sol-gel coatings to metals exposed to highly corrosive materials is restricted due to the substantial porosity of the films. Recent studies report that this limiting factor can be diminished by adding inorganic nanoparticles to the polymeric matrices, significantly improving the anticorrosive properties of the coatings. Considering the above, this work evaluated the inclusion of iron oxide nanoparticles (III) in zirconium polymeric matrices for the protection of 316 and 316L stainless steel. Electrochemical techniques, such as polarization curves and electrochemical impedance spectroscopy and morphological analysis with atomic force microscopy were used for this purpose. The responses obtained showed improvements in the anticorrosive properties of the zirconium films when doped with nanoparticles, and the best protective response was obtained with the minimum amount of the nanomaterial, aided by a significant increase in the metallic material's passivity. A critical content of nanoparticles was also identified in the polymeric matrix, above which the coating suffers serious deterioration, caused by the apparent formation of percolation channels leading to the oversaturation of the polymeric matrix

Pressure-induced changes in Cr3+-doped elpasolites and LiCaAlF6: Interpretation of macroscopic data

DEFF Research Database (Denmark)

Trueba, A. ,; García Lastra, Juan Maria; Aramburu, J. A.

2010-01-01

In the research of pressure effects on Cr3+-doped insulating lattices, it is crucial to understand the dependence of the 10Dq parameter on the sample volume, V. This problem is explored in the present work through ab initio calculations on Cr3+-doped K2NaScF6, Cs2NaYCl6, and Cs2NaYBr6 elpasolite...... dependence on V−m/3 for LiCaAlF6:Cr3+ where the measured exponent m=2.3 is seemingly anomalous when compared to the values found for ruby (m=4.5) or NiO (m=5)....

Superconductivity and magnetism in Ir-doped GdFeAsO

Energy Technology Data Exchange (ETDEWEB)

Cui, Y.J.; Chen, Y.L. [Key Laboratory of Magnetic Levitation and Maglev Trains (Ministry of Education of China), Superconductivity R and D Center (SRDC), Mail Stop 165, Southwest Jiaotong University, Chengdu, Sichuan 610031 (China); Cheng, C.H. [School of Materials Science and Engineering, University of New South Wales, Sydney 2052 NSW (Australia); Yang, Y.; Jiang, J.; Wang, Y.Z.; Zhang, Y. [Key Laboratory of Magnetic Levitation and Maglev Trains (Ministry of Education of China), Superconductivity R and D Center (SRDC), Mail Stop 165, Southwest Jiaotong University, Chengdu, Sichuan 610031 (China); Zhao, Y., E-mail: yzhao@swjtu.edu.c [Key Laboratory of Magnetic Levitation and Maglev Trains (Ministry of Education of China), Superconductivity R and D Center (SRDC), Mail Stop 165, Southwest Jiaotong University, Chengdu, Sichuan 610031 (China); School of Materials Science and Engineering, University of New South Wales, Sydney 2052 NSW (Australia)

2010-11-01

The 5d-transition metal, Ir has successfully been doped at Fe site and induced superconductivity in GdFeAsO at T{sub c} = 18.9 K and {approx}20 atom%. The Ir-doping shortened the c-axis length and stretched the a-axis one, which led to enhance the coupling between the FeAs- and SmO-layer, and to weaken the bonding between Fe and As atom. Paramagnetism was observed in all of the samples, which was resulted from the magnetic Gd ion as in the F-doped GdFeAsO. An upper critical field of GdFe{sub 0.8}Ir{sub 0.2}AsO was extrapolated to around 24 T, much smaller than that of F-doped GdFeAsO owing to a relatively low T{sub c} and small value of dH{sub c2}/dT.

Effect of concentration variation on 2.0 µm emission of Ho3+-doped SiO2-Al2O3-Na2CO3-SrF2-CaF2 oxyfluorosilicate glasses

Science.gov (United States)

Gelija, Devarajulu; Borelli, Deva Prasad Raju

2018-02-01

The concentration variation of Ho3+ ion-doped SiO2-Al2O3-Na2CO3-SrF2-CaF2 glasses has been prepared by conventional melt quenching method. The thermal stability of 1 mol % of Ho3+-doped oxyfluorosilicate glass has been calculated using the differential thermal analysis (DTA) spectra. The phenomenological Judd-Ofelt intensity parameters Ωλ ( λ = 2, 4 and 6) were calculated for all concentrations of Ho3+ ions. The luminescence spectra in visible region of Ho3+ ion-doped glasses were recorded under the excitation wavelength of 452 nm. The spectra consists of several intense emission bands (5F4, 5S2) → 5I8 (547 nm), 5F3 → 5I8 (647 nm), 5F5 → 5I7 (660 nm) and (5F4, 5S2) → 5I7 (750 nm) in the range 500-780 nm. The fluorescence emission at ˜2.0 µm (5I7 → 5I8) was observed under the excitation of 488 nm Ar-ion laser. The stimulated emission cross section for 5I7 → 5I8 transition (˜2.0 µm) varies from 8.46 to 9.52 × 10-21 cm2, as calculated by the Fuchtbauer-Ladenburg (FL) theory. However, Mc-Cumber theory was used to calculate emission cross section values about 4.24-5.75 × 10-21 cm2 for the 5I7 → 5I8 transition in all concentrations of Ho3+-doped oxyfluorosilicate glasses. Therefore, these results reveal that the 0.5 mol % of Ho3+-doped oxyfluorosilicate glasses, exhibiting higher emission cross section, has potentially been used for laser applications at ˜ 2.0 µm.

Shear Behavior of Corrugated Steel Webs in H Shape Bridge Girders

Directory of Open Access Journals (Sweden)

Qi Cao

2015-01-01

Full Text Available In bridge engineering, girders with corrugated steel webs have shown good mechanical properties. With the promotion of composite bridge with corrugated steel webs, in particular steel-concrete composite girder bridge with corrugated steel webs, it is necessary to study the shear performance and buckling of the corrugated webs. In this research, by conducting experiment incorporated with finite element analysis, the stability of H shape beam welded with corrugated webs was tested and three failure modes were observed. Structural data including load-deflection, load-strain, and shear capacity of tested beam specimens were collected and compared with FEM analytical results by ANSYS software. The effects of web thickness, corrugation, and stiffening on shear capacity of corrugated webs were further discussed.

High level caves rheological studies of tanks 15H, 42H, and 8F sludge/slurries

International Nuclear Information System (INIS)

Hamm, B.A.

1984-01-01

Samples of sludge were diluted to varying solids loading with salt-supernate, deionized water or pH 12 solution (0.01M NaOH). Rheological and physical property determinations were made. There was not a large change in rhelogical properties of sludge following aluminum dissolution, and a dissolved solids contribution to yield stress was not observed. The tank 15/42 and GIW-79 sludges had aluminum concentrations from 14 to 28 wt %. The tank 8 and GIW-82 sludges had aluminum concentrations from 6 to 8 wt %. The high aluminum sludges showed a more rapid increase in yield stress as a function of insoluble solids than the low aluminum sludges. The synthetic sludge formulation used in the GIW-79 study was a fairly good match for tank 15/42 sludge and the GIW-82 formulation was a fairly food match for tank 8 sludge when comparing yield stress and consistency relationship to insoluble solids. The tank 15/42 results indicate a yield stress of about 200 dynes/cm 2 at 13 wt % insoluble solids. The tank 8 results show a yield stress of about 80 dynes/cm 2 at 19 wt % insoluble solids. The calculational procedure used yields a conservative upper limit on the value of yield stress. For sludge transfer from F to H-area (30 to 50 dynes/cm 2 ), the tank 8 sludge concentration range was 3 to 18 wt % insoluble solids. For transfer from H to S-area (30 to 100 dynes/cm 2 ), the tank 8 concentration range was 3 to 22 wt % insoluble solids and the tank 15/42 range was found to be 6 to 11 wt % insoluble solids

Radiation effects on low cycle fatigue properties of reduced activation ferritic/martensitic steels

International Nuclear Information System (INIS)

Hirose, T.; Tanigawa, H.; Ando, M.; Kohyama, A.; Katoh, Y.; Narui, M.

2002-01-01

The reduced activation ferritic/martensitic steel, RAFs F82H IEA heat has been fatigue-tested at ambient temperature under diametral strain controlled conditions. In order to evaluate the effects of radiation damage and transmutation damage on fatigue characteristics, post-neutron irradiation and post-helium ion implantation fatigue tests were carried out. Fracture surfaces and fatigue crack initiation on the specimen surface were observed by SEM. Low-temperature irradiation caused an increase in stress amplitude and a reduction in fatigue lifetime corresponding to radiation hardening and loss of ductility. Neutron irradiated samples showed brittle fracture surface, and it was significant for large strain tests. On the other hand, helium implantation caused delay of cyclic softening. However, brittle crack initiation and propagation did not depend on the helium concentration profiles

Laser Cladding of CPM Tool Steels on Hardened H13 Hot-Work Steel for Low-Cost High-Performance Automotive Tooling

Science.gov (United States)

Chen, J.; Xue, L.

2012-06-01

This paper summarizes our research on laser cladding of high-vanadium CPM® tool steels (3V, 9V, and 15V) onto the surfaces of low-cost hardened H13 hot-work tool steel to substantially enhance resistance against abrasive wear. The results provide great potential for fabricating high-performance automotive tooling (including molds and dies) at affordable cost. The microstructure and hardness development of the laser-clad tool steels so obtained are presented as well.

Corrosion of 316 stainless steel in high temperature molten Li{sub 2}BeF{sub 4} (FLiBe) salt

Energy Technology Data Exchange (ETDEWEB)

Zheng, Guiqiu, E-mail: guiqiuzheng@gmail.com; Kelleher, Brian; Cao, Guoping; Anderson, Mark; Allen, Todd; Sridharan, Kumar

2015-06-15

In support of structural material development for the fluoride-salt-cooled high-temperature reactor (FHR), corrosion tests of 316 stainless steel were performed in the potential primary coolant, molten Li{sub 2}BeF{sub 4} (FLiBe) at 700 °C for an exposure duration up to 3000 h. Tests were performed in both 316 stainless steel and graphite capsules. Corrosion in both capsule materials occurred by the dissolution of chromium from the stainless steel into the salt which led to the depletion of chromium predominantly along the grain boundaries of the test samples. The samples tested in graphite capsules showed a factor of two greater depth of corrosion attack as measured in terms of chromium depletion, compared to those tested in 316 stainless steel capsules. The samples tested in graphite capsules showed the formation of Cr{sub 7}C{sub 3} particulate phases throughout the depth of the corrosion layer. Samples tested in both types of capsule materials showed the formation of MoSi{sub 2} phase due to increased activity of Mo and Si as a result of Cr depletion, and furthermore corrosion promoted the formation of a α-ferrite phase in the near-surface regions of the 316 stainless steel. Based on the corrosion tests, the corrosion attack depth in FLiBe salt was predicted as 17.1 μm/year and 31.2 μm/year for 316 stainless steel tested in 316 stainless steel and in graphite capsules respectively. It is in an acceptable range compared to the Hastelloy-N corrosion in the Molten Salt Reactor Experiment (MSRE) fuel salt.

Some loop experiments in the NRX reactor to study the corrosion of mild steel by flowing water at 90oF

International Nuclear Information System (INIS)

Allison, G.M.

1956-11-01

This work was undertaken to find the water conditions necessary for minimum corrosion in the mild steel thermal shield recirculating systems in NRX and NRU. This report contains the chemical and corrosion results obtained by operating three mild steel loops in which water at 85-95 o F was recirculated through test sections located in J-rod positions in the NRX reactor. Lowest corrosion rates were found when the water was maintained at pH 10.5 with or without oxygen being present. In both cases the corrosion was general in nature and no pitting occurred. At pH 7 with oxygen present in the water severe pitting took place and the corrosion rate was several times higher than similar conditions without oxygen in the water. Under oxygen-free conditions the corrosion product was Fe 3 O 4 . At pH 7 and with 3-5 ppm of O 2 in the water the corrosion product was a mixture of Fe 3 O 4 and γ-Fe 2 O 3 . At high pH with oxygen present Fe 3 O 4 predominated with some traces of Fe 2 O 3 . The systems tested may he listed in order of increasing corrosiveness: High pH with or without O 2 in the water 2 present and continual purification 2 present and no purification or pH control 2 present. (author)

Optical properties of lithium magnesium borate glasses doped with Dy3+ and Sm3+ ions

International Nuclear Information System (INIS)

Yasser Saleh Mustafa Alajerami; Suhairul Hashim; Wan Muhamad Saridan Wan Hassan; Ahmad Termizi Ramli; Azman Kasim

2012-01-01

Several studies showed the interesting properties of trivalent lanthanide ions when doped in various types of glasses. Optical and physical properties of lithium magnesium borate glasses doped with Dy 3+ then with Sm 3+ ions were determined by measuring their absorption and luminescence spectra in the visible region. The absorption spectra of Dy 3+ showed eight absorption bands with hypersensitive transition at 1265 nm ( 6 H 15/2 → 6 F 11/2 - 6 H 9/2 ) and three PL emission bands at 588 nm ( 4 F 9/2 → 6 H 15/2 ), 660 nm ( 4 F 9/2 → 6 H 13/2 ) and 775 nm ( 4 F 9/2 → 6 H 11/2 ). Regarding the Sm3 + , nine absorption bands were observed with hypersensitive transition at 1237 nm ( 6 H 5/2 - 6 F 7/2 ); the PL spectrum showed four prominent peaks at 4 G 5/2 → 6 H 5/2 (yellow color), 4 G 5/2 → 6 H 7/2 (bright orange color), 4 G 5/2 → 6 H 9/2 (orange reddish color) and 4 G 5/2 → 6 H 11/2 (red color), respectively. Finally, a series of physical parameters such as the oscillator strengths, refractive index, ions concentration, Polaron radius and other parameters were calculated for each dopant.

Evaluation of the mechanical properties of Niobium modified cast AISI H 13 hot work tool steel

International Nuclear Information System (INIS)

Noorian, A.; Kheirandish, Sh.; Saghafian, H.

2010-01-01

In this research, the effects of partially replacing of vanadium and molybdenum with niobium on the mechanical properties of AISIH 13 hot-work tool steel have been studied. Cast samples made of the modified new steel were homogenized and austenitized at different conditions, followed by tempering at the specified temperature ranges. Hardness, red hardness, three point bending test and Charpy impact test were carried out to evaluate the mechanical properties together with characterizing the microstructure of the modified steel using scanning electron microscope. The results show that niobium addition modifies the cast structure of Nb-alloyed steel, and increases its maximum hardness. It was found that bending strength; bending strain, impact strength, and red hardness of the modified cast steel are also higher than those of the cast H13 steel, and lower than those of the wrought H13 steel.

Hardness of H13 Tool Steel After Non-isothermal Tempering

Science.gov (United States)

Nelson, E.; Kohli, A.; Poirier, D. R.

2018-04-01

A direct method to calculate the tempering response of a tool steel (H13) that exhibits secondary hardening is presented. Based on the traditional method of presenting tempering response in terms of isothermal tempering, we show that the tempering response for a steel undergoing a non-isothermal tempering schedule can be predicted. Experiments comprised (1) isothermal tempering, (2) non-isothermal tempering pertaining to a relatively slow heating to process-temperature and (3) fast-heating cycles that are relevant to tempering by induction heating. After establishing the tempering response of the steel under simple isothermal conditions, the tempering response can be applied to non-isothermal tempering by using a numerical method to calculate the tempering parameter. Calculated results are verified by the experiments.

Efficient charge carriers induced by extra outer-shell electrons in iron-pnictides: a comparison between Ni- and Co-doped CaFeAsF

International Nuclear Information System (INIS)

Zhang Min; Yu Yi; Tan Shun; Zhang Yuheng; Zhang Changjin; Zhang Lei; Qu Zhe; Ling Langsheng; Xi, Chuanying

2010-01-01

A comprehensive study of the difference between CaFe 1-x Ni x AsF and CaFe 1-x Co x AsF systems has been carried out by measuring the efficient charge carrier concentration, the valence states and the superconducting phase diagram. It is found that at the same doping level, Ni doping introduces nearly twice the number of charge carriers as Co doping. However, x-ray absorption near-edge spectroscopy measurements reveal that the valence state of Fe in both systems is close to 2, indicating that there is no valence mismatch. We suggest that the charge carriers in CaFe 1-x M x AsF (M=transition metal elements) are not induced by valence mismatch but come from the difference in the number of outer-shell electrons. We also suggest that with Ni and Co doping, the systems change from a multi-band material in the underdoped regions to a single-band state in the overdoped regions.

Mechanism of luminescent emission in BaY2F8 scintillators doped with rare earths

International Nuclear Information System (INIS)

Santos, Ana Carolina de Mello

2013-01-01

In this work samples of Barium Yttrium Fluoride (BaY 2 F 8 -BaYF) doped with different concentrations of Tb 3+ , Er 3+ , Tm 3+ e Nd 3+ ions were characterized, aiming their application in radiation detection devices using their scintillating properties. Two types of samples were produced, polycrystalline samples, obtained via solid state reaction and single crystals, obtained via the floating zone melting method. The radioluminescence measurements (RL) revealed that the samples doped with 2.0 or 3.0 % Tb showed RL intensity at 545 nm two times higher than samples of CsI:Tl, although the total scintillation yield was smaller when compared to this commercial scintillator. Thermoluminescence (TL) results showed that all doped samples exhibited the same peak at 123°C, which is characteristic of the matrix (BaY 2 F 2 ). Comparison of the areas under the TL and RL curves for Tb 3+ and Nd 3+ doped BaYF revealed that the trapping centers are competing with the scintillation of the samples. However, this was not true for the Er 3+ and Tm 3+ doped samples and it was found that the scintillation yield is independent of the trap concentration up to a certain concentration limit. From this point on, the scintillation yields started increasing as the trap concentration increased. The radiation damage defects in BaYF:Tb 3+ were studied via optical absorption (OA) and correlated with TL, showing that trapping centers are connected to the color centers. All samples exhibited different luminescence decay processes with time constants ranging from microseconds, for the fast processes, milliseconds, for the intermediate ones, and phosphorescent processes with decay time on the order of seconds. For the Nd 3+ doped samples, very fast decay process was also found with time constants of about 60ns and that is an indication that this material can be used in fast detection systems, although its scintillation efficiency was weak. The combined results obtained with these techniques together

Spectral response of REE3+ doped LaAlO3

International Nuclear Information System (INIS)

Boronat, C.; Correcher, V.; Garcia G, J.; Morales, A.; Zarate, J.; Rivera, T.

2016-10-01

This paper reports on the preliminary results obtained from the cathodoluminescence (Cl) and thermoluminescence (Tl) properties of undoped LaAlO 3 (LAO) and LaAlO 3 : REE (REE=Dy 3+ , Pr 3+ and Eu 3+ ) to be potentially employed for dosimetric purposes. The samples were synthesized by a sol-gel process based on the Pechini 's method with a spray-drying technique and, subsequently, characterized by environmental scanning electron microscopy and energy dispersive X-ray analysis spectrometry. Cl spectra display sharp and narrow wavebands that could specifically be associated with structural (in the range of 300-450 nm) and point defects (from 450 to 800 nm). The observed wavebands could be assigned as follows: (i) 480 and 570 from the Dy-doped LAO should corresponding respectively to 4 F 9/2 → 6 H 15/2 and 4 F 9/2 → 6 H 13/2 transitions, (II) 490-638 from the Pr-doped LAO is linked to 3 P 0 → 3 H 4 , 1 D 2 → 3 H 4 transitions and (III) 590 and 620 where the dopant Eu 3+ gives rise to 5 D 0 → 7 F 1 and 5 D 0 → 7 F 2 transitions and (IV) a UV-blue broad band is associated with NBOHC in undoped LAO. Such emissions are due to the presence of the 4f electrons of rare earth ions that are shielded by the outer 5s and 5p electrons, the intra-4f emission spectra of REE. Furthermore, the study performed on the Tl emission of LaAlO 3 :Dy 3+ displays (i) two maxima centred at 150 and 240 degrees Celsius (ratio 1:2) similarly to the Pr 3+ doped sample but with 7:5 of ratio. And (II) the highest radiation sensitivity, allowing us to think on the potential use of this material for dosimetric purposes, however further works are necessary to confirm such assertion. (Author)

Effect of concentration variation on 2.0 μm emission of Ho3+-doped SiO2-Al2O3-Na2CO3-SrF2-CaF2 oxyfluorosilicate glasses

International Nuclear Information System (INIS)

Gelija, Devarajulu; Borelli, Deva Prasad Raju

2018-01-01

The concentration variation of Ho 3+ ion-doped SiO 2 -Al 2 O 3 -Na 2 CO 3 -SrF 2 -CaF 2 glasses has been prepared by conventional melt quenching method. The thermal stability of 1 mol % of Ho 3+ -doped oxyfluorosilicate glass has been calculated using the differential thermal analysis (DTA) spectra. The phenomenological Judd-Ofelt intensity parameters Ω λ (λ = 2, 4 and 6) were calculated for all concentrations of Ho 3+ ions. The luminescence spectra in visible region of Ho 3+ ion-doped glasses were recorded under the excitation wavelength of 452 nm. The spectra consists of several intense emission bands ( 5 F 4 , 5 S 2 ) → 5 I 8 (547 nm), 5 F 3 → 5 I 8 (647 nm), 5 F 5 → 5 I 7 (660 nm) and ( 5 F 4 , 5 S 2 ) → 5 I 7 (750 nm) in the range 500-780 nm. The fluorescence emission at ∝ 2.0 μm ( 5 I 7 → 5 I 8 ) was observed under the excitation of 488 nm Ar-ion laser. The stimulated emission cross section for 5 I 7 → 5 I 8 transition (∝ 2.0 μm) varies from 8.46 to 9.52 x 10 -21 cm 2 , as calculated by the Fuchtbauer-Ladenburg (FL) theory. However, Mc-Cumber theory was used to calculate emission cross section values about 4.24-5.75 x 10 -21 cm 2 for the 5 I 7 → 5 I 8 transition in all concentrations of Ho 3+ -doped oxyfluorosilicate glasses. Therefore, these results reveal that the 0.5 mol % of Ho 3+ -doped oxyfluorosilicate glasses, exhibiting higher emission cross section, has potentially been used for laser applications at ∝ 2.0 μm. (orig.)

An All-Solid-State pH Sensor Employing Fluorine-Terminated Polycrystalline Boron-Doped Diamond as a pH-Insensitive Solution-Gate Field-Effect Transistor.

Science.gov (United States)

Shintani, Yukihiro; Kobayashi, Mikinori; Kawarada, Hiroshi

2017-05-05

A fluorine-terminated polycrystalline boron-doped diamond surface is successfully employed as a pH-insensitive SGFET (solution-gate field-effect transistor) for an all-solid-state pH sensor. The fluorinated polycrystalline boron-doped diamond (BDD) channel possesses a pH-insensitivity of less than 3mV/pH compared with a pH-sensitive oxygenated channel. With differential FET (field-effect transistor) sensing, a sensitivity of 27 mv/pH was obtained in the pH range of 2-10; therefore, it demonstrated excellent performance for an all-solid-state pH sensor with a pH-sensitive oxygen-terminated polycrystalline BDD SGFET and a platinum quasi-reference electrode, respectively.

Investigation on the effect of chemical composition on the texture and bake hardening I F steels

International Nuclear Information System (INIS)

Kariman, M.; Motaghi, A.; Raygan, Sh.; Habibi Parsa, M.; Nili Ahmadabadi, M.

2008-01-01

Interstitial free steels have good formability and also excellent deep draw ability. These features make them one of the applicable materials in automotive industry. Chemical composition and thermomechanical treatment used to process these steels have important role in final properties of them. In this study, the effect of chemical composition on texture, anisotropic properties and bake harden ability of these steels were investigated. The results showed that contribution of vanadium as a weak carbonitride former element with titanium as strong carbonitride former could change the texture of steels. Replacing titanium with vanadium caused harmful effect on mechanical properties. In this research deep drawing properties of five steels were compared based on I {111} / I{001} and I {111} / I{110} parameters. The results of bake harden ability test showed that there were critical limits for vanadium volume fractions above which bake harden properties was improved. It was shown that the bake harden properties of Nb-steels were better than that of Ti-steels. This was due to the better solution of Nb(C,N) compared to Ti(C,N). Addition of vanadium to Ti-steels may improve bake harden properties of I F steels

Flower colour modification of chrysanthemum by suppression of F3'H and overexpression of the exogenous Senecio cruentus F3'5'H gene.

Directory of Open Access Journals (Sweden)

Huang He

Full Text Available Chrysanthemum (Chrysanthemum × morifolium is one of the most important ornamental plants in the world. They are typically used as cut flowers or potted plants. Chrysanthemum can exhibit red, purple, pink, yellow and white flowers, but lack bright red and blue flowers. In this study, we identified two chrysanthemum cultivars, C × morifolium 'LPi' and C × morifolium 'LPu', that only accumulate flavonoids in their ligulate flowers. Next, we isolated seven anthocyanin biosynthesis genes, namely CmCHS, CmF3H, CmF3'H, CmDFR, CmANS, CmCHI and Cm3GT in these cultivars. RT-PCR and qRT-PCR analyses showed that CmF3'H was the most important enzyme required for cyanidin biosynthsis. To rebuild the delphinidin pathway, we downregulated CmF3'H using RNAi and overexpressed the Senecio cruentus F3'5'H (PCFH gene in chrysanthemum. The resultant chrysanthemum demonstrated a significantly increased content of cyanidin and brighter red flower petals but did not accumulate delphinidin. These results indicated that CmF3'H in chrysanthemum is important for anthocyanin accumulation, and Senecio cruentus F3'5'H only exhibited F3'H activity in chrysanthemum but did not rebuild the delphinidin pathway to form blue flower chrysanthemum.

Flower colour modification of chrysanthemum by suppression of F3'H and overexpression of the exogenous Senecio cruentus F3'5'H gene.

Science.gov (United States)

He, Huang; Ke, Hu; Keting, Han; Qiaoyan, Xiang; Silan, Dai

2013-01-01

Chrysanthemum (Chrysanthemum × morifolium) is one of the most important ornamental plants in the world. They are typically used as cut flowers or potted plants. Chrysanthemum can exhibit red, purple, pink, yellow and white flowers, but lack bright red and blue flowers. In this study, we identified two chrysanthemum cultivars, C × morifolium 'LPi' and C × morifolium 'LPu', that only accumulate flavonoids in their ligulate flowers. Next, we isolated seven anthocyanin biosynthesis genes, namely CmCHS, CmF3H, CmF3'H, CmDFR, CmANS, CmCHI and Cm3GT in these cultivars. RT-PCR and qRT-PCR analyses showed that CmF3'H was the most important enzyme required for cyanidin biosynthsis. To rebuild the delphinidin pathway, we downregulated CmF3'H using RNAi and overexpressed the Senecio cruentus F3'5'H (PCFH) gene in chrysanthemum. The resultant chrysanthemum demonstrated a significantly increased content of cyanidin and brighter red flower petals but did not accumulate delphinidin. These results indicated that CmF3'H in chrysanthemum is important for anthocyanin accumulation, and Senecio cruentus F3'5'H only exhibited F3'H activity in chrysanthemum but did not rebuild the delphinidin pathway to form blue flower chrysanthemum.

Separative recovery with lime of phosphate and fluoride from an acidic effluent containing H3PO4, HF and/or H2SiF6.

Science.gov (United States)

Gouider, Mbarka; Feki, Mongi; Sayadi, Sami

2009-10-30

Fluoride content and flow-rate of fertilizer plant wastewater from phosphoric acid and/or triple superphosphate (TSP) production lead to the discharge of several thousand tons of fluoride (F(-)) per year and even more for phosphate (PO4(3-)). Since sustainability is an important environmental concern, the removal methods should allow phosphorus and fluoride to be recycled as a sustainable products for use as raw materials either in agricultural or industrial applications. In the present work, separative recovery with lime of these two target species was investigated. A preliminary speciation study, carried out on the crude effluent, showed that two forms of fluoride: HF and H2SiF6 are present in a highly acidic medium (pH approximately 2). Evidence that fluoride is present under both free (HF) and combined (H2SiF6) forms, in the phosphate-containing effluent, was provided by comparing potentiometric titration curves of a crude wastewater sample and synthetic acid mixtures containing H3PO4, HF and H2SiF6. In a second step synthetic effluent containing mixtures of the following acids: HF, H2SiF6 and H3PO4, were treated with lime. The behaviour of these compounds under lime treatment was analysed. The data showed that fluoride has a beneficial effect on phosphate removal. Moreover, by acting on the precipitation pH, a "selective" recovery of fluoride and phosphate ions was possible either from phosphoric acid/hydrofluoric acid or phosphoric acid/hexafluorosilicic acid mixtures. Indeed, the first stage of the separative recovery, led to a fluoride removal efficiency of 97-98% from phosphoric acid/hydrofluoric acid mixture. It was of 93-95% from phosphoric acid/hexafluorosilicic acid mixture. During the second stage, the phosphate precipitation reached 99.8% from both acidic mixtures whereas it did not exceed 82% from a solution containing H3PO4 alone. The XRD and IR analyses showed that during lime treatment, a H2SiF6 hydrolysis occurred, instead of CaSiF6 solid

Creep of ex-service AISI-316H steel at very low strain rates

Energy Technology Data Exchange (ETDEWEB)

Kloc, Lubos; Sklenicka, Vaclav [Academy of Sciences of the Czech Republic, Brno (Czech Republic). Inst. of Physics of Materials; Spindler, Michael [British Energy Generation, Barbwood, Gloucester (United Kingdom)

2010-07-01

The creep response of ex-service Type 316H austenitic steel was investigated at temperatures from 470 to 550 C and stresses from 80 to 120 MPa. These conditions lead to very low strain rates. Both helicoid spring specimen tests and conventional uniaxial creep tests were used to measure these very low creep strains. An internal stress model was used to analyse the creep curves and the results were compared to creep curves obtained on a Type 316H in the as-received condition, which for austenitic steels is after solution heat treatment. The creep behavior of the ex-service steel was very similar to that of the as-received steel. Thus, no creep damage or significant change of microstructure was detected during the service period of 65,000 hours at {proportional_to} 520 C. It was found that the helicoid spring specimen technique provides results compatible with that of conventional creep tests, but with superior accuracy with very low creep strains. (orig.)

Moessbauer spectroscopy study on the corrosion resistance of plasma nitrided ASTM F138 stainless steel in chloride solution

International Nuclear Information System (INIS)

Souza, S.D. de; Olzon-Dionysio, M.; Basso, R.L.O.; Souza, S. de

2010-01-01

Plasma nitriding of ASTM F138 stainless steel samples has been carried out using dc glow discharge under 80% H 2 -20% N 2 gas mixture, at 673 K, and 2, 4, and 7 h time intervals, in order to investigate the influence of treatment time on the microstructure and the corrosion resistance properties. The samples were characterized by scanning electron microscopy, glancing angle X-ray diffraction and conversion electron Moessbauer spectroscopy, besides electrochemical tests in NaCl aerated solution. A modified layer of about 6 μm was observed for all the nitrided samples, independent of nitriding time. The X-ray diffraction analysis shows broad γ N phase peaks, signifying a great degree of nitrogen supersaturation. Besides γ N, the Moessbauer spectroscopy results indicated the occurrence of γ' and ε phases, as well as some other less important phases. Corrosion measurements demonstrate that the plasma nitriding time affects the corrosion resistance and the best performance is reached at 4 h treatment. It seems that the ε/γ' fraction ratio plays an important role on the resistance corrosion. Additionally, the Moessbauer spectroscopy was decisive in this study, since it was able to identify and quantify the iron phases that influence the corrosion resistance of plasma nitrided ASTM F138 samples.

Initiation and developmental stages of steel corrosion in wet H2S environments

International Nuclear Information System (INIS)

Bai, Pengpeng; Zhao, Hui; Zheng, Shuqi; Chen, Changfeng

2015-01-01

Highlights: • The initiation and development stages of steel corrosion in wet H 2 S environment were investigated. • Preferential dissolution at the grain boundaries of steel allowed corrosion products to form and accumulate. • The shapes and crystal types of corrosion products at various steel layers differed. • With increasing duration time, the S 2− peak with a binding energy of 161.2 eV gradually decreased. • A model of the formation process of corrosion product films was proposed. - Abstract: The initiation and various developmental stages of steel corrosion in H 2 S environments were investigated using atomic force microscopy (AFM), scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS) and transmission electron microscopy (TEM). Results revealed that grain boundaries corrode at the initiation stage and that corrosion products initially form on both sides of the grain boundary and then accumulate. Corrosion products grew at the interface between the steel and corrosion product layer at the developmental stage. XPS analyses showed the composition and valence states of the corrosion products, and a model of the formation process of corrosion product films was proposed

Enhancement of luminescence properties in Er3+ doped TeO2-Na2O-PbX (X=O and F) ternary glasses.

Science.gov (United States)

Kumar, Kaushal; Rai, S B; Rai, D K

2007-04-01

An enhancement of luminescence properties in Er3+ doped ternary glasses is observed on the addition of PbO/PbF2. The infrared to visible upconversion emission bands are observed at 410, 525, 550 and 658 nm, due to the 2H9/2-->4I15/2, 2H11/2-->4I15/2, 4S3/2-->4I15/2, 4F9/2-->4I15/2 transitions respectively, on excitation with 797 nm laser line. A detailed study reveals that the 2H9/2-->4I15/2 transition arises due to three step upconversion process while other transitions arise due to two step absorption. On excitation with 532 nm radiation, ultraviolet and violet upconversion bands centered at 380, 404, 410 and 475 nm wavelengths are observed along with one photon luminescence bands at 525, 550, 658 and 843 nm wavelengths. These bands are found due to the 4G11/2-->4I15/2, 2P3/2-->4I13/2, 2H9/2-->4I15/2, 2P3/2-->4I11/2, 2H11/2-->4I15/2, 4S3/2-->4I15/2, 4F9/2-->4I15/2 and 4S3/2-->4I13/2 transitions, respectively. Though incorporation of PbO and PbF2 both enhances fluorescence intensities however, PbF2 content has an important influence on upconversion luminescence emission. The incorporation of PbF2 enhances the red emission (658 nm) intensity by 1.5 times and the violet emission (410 nm) intensity by 2.0 times. A concentration dependence study of fluorescence reveals the rapid increase in the red (4F9/2-->4I15/2) emission intensity relative to the green (4S3/2-->4I15/2) emission with increase in the Er3+ ion concentration. This behaviour has been explained in terms of an energy transfer by relaxation between excited ions.

Ce and Eu-doped LiSrAlF6 scintillators for neutron detectors

International Nuclear Information System (INIS)

Yanagida, Takayuki; Kawaguchi, Noriaki; Fujimoto, Yutaka; Yokota, Yuui; Yamazaki, Atsushi; Watanabe, Kenichi; Kamada, Kei; Yoshikawa, Akira; Chani, Valery

2011-01-01

Ce 1%, Eu 1%, and Eu 2%-doped LiSrAlF 6 (LiSAF) single crystals were grown by the micro-pulling-down method for thermal neutron applications. The crystals were transparent, 2.0 mm in diameter and 20–40 mm in length. Neither visible inclusions nor cracks were observed. Their transmittance spectra were measured. The strong absorption lines were observed at 200, 240, and 300 nm for Ce:LiSAF due to Ce 3+ 4f–5d transition. In Eu:LiSAF, 200 (4f–5d) and 300 (4f–4f) nm absorption lines were detected. The samples demonstrated strong emission peaks at 300 nm (Ce:LiSAF) and 370 nm (Eu:LiSAFs) when they were irradiated with 241 Am α-rays simulating the α-particles from the 6 Li(n, α) reaction. Thermal neutron responses were examined under 252 Cf irradiation. The absolute light yield of Ce, Eu 1%, and Eu 2% crystals were 3400, 18000, and 30000 ph/n, respectively. Main components of the scintillation decay time of Ce, Eu 1%, and Eu 2%-doped LiSAFs were 63, 1293, and 1205 ns.

Evaluation of H2S sensing characteristics of metals-doped graphene and metals-decorated graphene: Insights from DFT study

Science.gov (United States)

Khodadadi, Zahra

2018-05-01

The high tendency of graphene to adsorb H2S gas has made it a good choice for the purpose of separating H2S gas from industrial waste streams, and it can also be used as a good H2S sensor. In this research, the adsorption of H2S molecule on pristine, transition metal (Ni, Cu and Zn)-doped graphene and metal-decorated graphene nanosheets have been investigated via first-principles approach based on Density Functional Theory (DFT). The most stable adsorption geometry, rate of adsorption energy and charge transfer of H2S molecule on pristine, metal-doped, and metal-decorated graphene nanosheets have been discussed. The adsorption of H2S gas on several kinds of graphene nanosheets was studied by three different models. As H2S molecule adsorbed on metal-doped graphene nanosheets, we found that the configuration with two hydrogen atoms towards the metal-doped graphene nanosheet as most desirable situation. Moreover, the calculations show that the adsorption energy of H2S on Cu-doped graphene nanosheet is the highest among all the other metal-doped graphene nanosheet systems. We also investigated the H2S capability to bind to Ni, Cu and Zn-decorated graphene nanosheets. It was found that after adsorption, the configuration of the sulfur atom, which was located close to the metal-decorated graphene nanosheets was stable thermodynamically. The Ni-decorated graphene nanosheet with large adsorption energy and short binding distance is suitable for chemisorptions. The unfilled d-shells Ni-decorated graphene nanosheets are primarily responsible for increase in the reactivity.

Preparation of acridine orange-doped silica nanoparticles for pH measurement

International Nuclear Information System (INIS)

Liu, Jinshui; Zang, Lingjie; Wang, Yiru; Liu, Guoning

2014-01-01

Acridine orange was first encapsulated into silica shell via a facile reverse microemusion method to built core–shell fluorescent nanoparticles. The nanoparticles are all in spherical shape and have a narrow size distribution, and its application as a optical pH sensor has been demonstrated. This novel sensor is based on the pH-dependent fluorescence intensities of acridine orange in different pH value. The fluorescence intensity of acridine orange-doped silica nanoparticles was decreased by increasing pH value. Under optimum conditions, the changes of fluorescence intensity were proportional to the pH value in the range of 8.00–10.90. In addition, the sensor can be easily separated by centrifugation and adds no pollution to the environment compared to the free dyes. Furthermore, the effects of ionic strength and co-existing substances were proved to have little influence on the determination of pH. The sensor has been successfully applied to determine the pH of two artificial samples. Hence, the core–shell fluorescent nanoparticles show potential for practical application. -- Highlights: • Acridine orange was encapsulated into silica shell via a facile reverse microemusion method to built core–shell fluorescent nanoparticles. • The fluorescence intensity of acridine orange-doped silica nanoparticles was decreased by increasing pH value. • Its can be used as an optical pH sensor. • The sensor can be easily separated by centrifugation and adds no pollution to the environment compared to the free dyes. • The sensor has been successfully applied to determine the pH of artificial samples

Optical gain of LaF3:Nd nanoparticle doped polymers for active integrated optical devices

NARCIS (Netherlands)

Stouwdam, J.W.; Klunder, D.J.W.; Borreman, A.; Diemeer, Mart; Worhoff, Kerstin; Driessen, A.; de Ridder, R.M.; de Ridder, R.M; Altena, G; Altena, G.; Geuzebroek, D.H.; Dekker, R; Dekker, R.

2003-01-01

We report on rare earth doped LaF3 nanoparticles dispersed in PMMA and SU-8 photosensitive polymers. We observed optical gain after we applied these materials for waveguides. Experimental results on various samples will be discussed. We theoretically discuss the improvements that can be obtained and

Influence of tempering on mechanical properties of ferritic martensitic steels

International Nuclear Information System (INIS)

Chun, Y. B.; Han, C. H.; Choi, B. K.; Lee, D. W.; Kim, T. K.; Jeong, Y. H.; Cho, S.

2012-01-01

In the mid-1980s research programs for development of low activation materials began. This is based on the US Nuclear Regulatory Commission Guidelines (10CFR part 61) that were developed to reduce long-lived radioactive isotopes, which allows nuclear reactor waste to be disposed of by shallow land burial when removed from service. Development of low activation materials is also key issue in nuclear fusion systems, as the structural components can became radioactive due to nuclear transmutation caused by exposure to high dose neutron irradiation. Reduced-activation ferritic martensitic (RAFM) steels have been developed in the leading countries in nuclear fusion technology, and are now being considered as primary candidate material for the test blanket module (TBM) in the international thermonuclear experiment reactor (ITER). RAFM steels developed so far (e.g., EUROFER 97 and F82H) meet the requirement for structural application in the ITER. However, if such alloys are used in the DEMO or commercial fusion reactor is still unclear, as the reactors are designed to operate under much severe conditions (i.e., higher outlet coolant temperature and neutron fluences). Such harsh operating conditions lead to development of RAFM steels with better creep and irradiation resistances. Mechanical properties of RAFM steels are strongly affected by microstructural features including the distribution, size and type of precipitates, dislocation density and grain size. For a given composition, such microstructural characteristics are determined mainly by thermo-mechanical process employed to fabricate the final product, and accordingly a final heat treatment, i.e., tempering is the key step to control the microstructure and mechanical properties. In the present work, we investigated mechanical properties of the RAFM steels with a particular attention being paid to effects of tempering on impact and creep properties

Investigation of the multiphotonic excitation processes of the 4f2 5d configuration in LiYF4, LiLuF4 and BaY2F8 crystals doped with trivalent neodymium

International Nuclear Information System (INIS)

Librantz, Andre Felipe Henriques

2004-01-01

Ultraviolet (UV) fluorescence of Nd 3+ ions induced by multistep laser excitation was investigated in Nd-doped LiYF 4 (YLF), LiLuF 4 (LLF) and BaY 2 F 8 (BaYF) crystals using a technique of time-resolved spectroscopy. The observed UV luminescence was due to transitions between the bottom of 4f 2 5d configuration and the 4f 3 states of Nd 3+ ions. The lower excited state 4f 2 ( 3 H)5d [ 4 K 11/2 ] was reached by three stepwise absorptions of photons at 521 nm (green) and 478 nm (blue) of a short pulse laser excitation. The three sequential absorptions at 478 nm constitutes a new multiphoton excitation process of Nd 3+ in these crystals with the following excitation sequence: 4 I 9/2 + hv(480 nm)→ 2 G(1) 9/2 + hv(480 nm)→ 2 F(2) 7/2 + hv(480 nm)→ 4f 2 ( 3 H)5d [ 4 K 9/2 ] (excited state at ∼ 63000 cm -1 ). The observed UV emissions from [ 4 K 11/2 ] state have a lifetime of 35 ns (parity allowed) and are: broadband in contrast to UV emissions from 4f 3 configuration, which are also present in the luminescence investigation but having longer lifetime (8 μs) and structures composed of narrow lines. The excitation spectrum of fast UV luminescence exhibited different structure depending on the excitation geometry (σ or π) with respect to the c-axis of the crystal. It was seen two new emissions from [ 4 K 11/2 ] and 2 F(2) 5/2 states near 528 nm, which modified the branching ratio of the bottom of the 4f 2 5d configuration (∼ 55500 cm -1 for the YLF and LLF crystals and ∼-53700 cm -1 for the BaYF crystal). The equivalent cross-section of three and two excitation process was estimated at 521 nm by solving the rate equations of the system under short laser excitation, which leads us to infer that is possible to have laser action under pulsed laser pumping with intensity below the crystal damage threshold. (author)

Mechanoluminescence by impulsive deformation of γ-irradiated Er-doped CaF2 crystals

International Nuclear Information System (INIS)

Brahme, Nameeta; Shukla, Manju; Bisen, D.P.; Kurrey, U.; Choubey, Anil; Kher, R.S.; Singh, Manisha

2011-01-01

An impulsive technique has been used for mechanoluminescence (ML) measurements in γ-irradiated Er doped CaF 2 crystals. When the ML is excited impulsively by the impact of moving piston on to γ-irradiated CaF 2 :Er crystals, two peaks are observed in ML intensity with time and it is seen that the peak intensities of first and second peaks (I m1 and I m2 ) increase with increasing impact velocity. However the time corresponding to first and second peaks (t m1 and t m2 ) shifts towards shorter time values with increasing impact velocity. It is also seen that the total ML intensity I Total initially increases with the impact velocity and then it attains a saturation value for higher values of the impact velocity. We have presented a theoretical explanation for the observed results. - Research highlights: → Impulsive technique has been used for mechanoluminescence (ML) studies in γ-irradiated Er doped CaF 2 crystals. → ML intensity exhibited two peaks with time (I m1 and I m2 ), where the intensity of both the peaks increased with increasing impact velocity. → The time of occurrence of the peaks (t m1 and t m2 ) reduced with increasing the impact velocity. → Total ML intensity (I Total ) first increases and then attains a saturation value with an increment in the impact velocity. → A theoretical explanation is presented to the observed results.

Effect of coatings on long term behaviour of a commercial stainless steel for solid oxide electrolyser cell interconnect application in H2/H2O atmosphere

International Nuclear Information System (INIS)

Ardigo, M.R.; Popa, I.; Chevalier, S.; Girardon, P.; Perry, F.; Laucournet, R.; Brevet, A.; Desgranges, C.

2014-01-01

K41X (AISI 441) stainless steel evidenced a high electrical conductivity after 3000 h ageing in H 2 /H 2 O side when used as interconnect for solid oxide electrolyser cells (SOEC) working at 800 C. Perovskite (La 1-x Sr x MnO 3-δ ) and spinel (Co 3 O 4 ) oxides coatings were applied on the surface of the ferritic steel for ageing at 800 C for 3000 h. Both coatings improved the behaviour of the steel and give interesting opportunities to use the K41X steel as interconnect for hydrogen production via high temperature steam electrolysis. Co 3 O 4 reduced into Co leading to a very good Area Specific Resistance (ASR) parameter, 0.038 Ωcm 2 . Despite a good ASR (0.06 Ωcm 2 ), La 1-x Sr x MnO 3-δ was less promising because it partially decomposed into MnO and La 2 O 3 during ageing in H 2 /H 2 O atmosphere. (authors)

Corrosion of austenitic and ferritic-martensitic steels exposed to supercritical carbon dioxide

International Nuclear Information System (INIS)

Tan, L.; Anderson, M.; Taylor, D.; Allen, T.R.

2011-01-01

Highlights: → Oxidation is the primary corrosion phenomenon for the steels exposed to S-CO 2 . → The austenitic steels showed significantly better corrosion resistance than the ferritic-martensitic steels. → Alloying elements (e.g., Mo and Al) showed distinct effects on oxidation behavior. - Abstract: Supercritical carbon dioxide (S-CO 2 ) is a potential coolant for advanced nuclear reactors. The corrosion behavior of austenitic steels (alloys 800H and AL-6XN) and ferritic-martensitic (FM) steels (F91 and HCM12A) exposed to S-CO 2 at 650 deg. C and 20.7 MPa is presented in this work. Oxidation was identified as the primary corrosion phenomenon. Alloy 800H had oxidation resistance superior to AL-6XN. The FM steels were less corrosion resistant than the austenitic steels, which developed thick oxide scales that tended to exfoliate. Detailed microstructure characterization suggests the effect of alloying elements such as Al, Mo, Cr, and Ni on the oxidation of the steels.

Estimation of flow stress of radiation induced F/M steels using molecular dynamics and discrete dislocation dynamics approach

International Nuclear Information System (INIS)

More, Ameya; Dutta, B.K.; Durgaprasad, P.V.; Arya, A.K.

2012-01-01

Fe-Cr based Ferritic/Martensitic (F/M) steels are the candidate structural materials for future fusion reactors. In this work, a multi-scale approach comprising atomistic Molecular Dynamics (MD) simulations and Discrete Dislocation Dynamics (DDD) simulations are used to model the effect of irradiation dose on the flow stress of F/M steels. At the atomic scale, molecular dynamics simulations are used to study the dislocation interaction with irradiation induced defects, i.e. voids and He bubbles. Whereas, the DDD simulations are used to estimate the change in flow stress of the material as a result of irradiation hardening. (author)

Vacuum-annealing induced enhancements in the transparent conducting properties of Mo  +  F doped ZnO thin films

Science.gov (United States)

Dineshbabu, N.; Ravichandran, K.

2017-09-01

The decisive aim of the present study is to enhance the transparent conducting properties of Mo  +  F co-doped ZnO films through annealing. In this work, Mo  +  F co-doped ZnO (MFZO) films were deposited on glass substrates at a deposition temperature of 350 °C using a home-made nebulizer spray pyrolysis technique and the prepared samples were annealed under air and vacuum atmosphere at 400 °C for 2 h. The structural, electrical, optical, surface morphological and elemental properties of as-deposited, air-annealed and vacuum-annealed samples were compared using various analytical techniques. The vacuum-annealed sample shows lowest resistivity of 1.364  ×  10-3 Ω cm and high transmittance of 90% in the visible region with high ohmic conducting nature. The optical bandgap of the sample was found to be increased to 3.36 eV after vacuum annealing treatment. The XRD patterns of the films confirmed the polycrystalline nature. The PL measurements show the defect levels of the deposited films. The FESEM and AFM studies show an increase in the grain size and roughness of the films, respectively, after vacuum-annealing treatment. The presence of the elements before and after annealing treatment was confirmed using XPS analysis.

Synthesis of calcium doped lanthanum manganite by mechanosynthesis

International Nuclear Information System (INIS)

Bolarin, A.M.; Sanchez, F.; Palomares, S.; Aguilar, J.A.; Torres-Villasenor, G.

2007-01-01

Lanthanum manganite doped with calcium, Ca 1/3 La 2/3 MnO 3-δ , was prepared by a high-energy ball milling. The precursors used were Mn 2 O 3 , La 2 O 3 and CaO, mixed in the stoichiometric ratio to obtain this manganite. The mechano-chemical process was performed at room temperature in a SPEX 8000D mixer/mill, using hardened steel balls and stainless steel vials, in air atmosphere. X-ray diffraction was used to elucidate the phase transformation as a function of the milling time. The Rietveld refinement was used in order to characterize structurally the manganites. The morphology and particle size of powder compound obtained were characterized by scanning electron microscope. The particle size of this powder material was measured with zeta size analyzer, and selected area electron diffraction (SAED) from TEM was used to elucidate the crystalline structure of this powder compound. The results showed that it is possible to obtain calcium doped lanthanum manganite by mechano-synthesis, using a weight ratio of ball to powder of 12:1, after 3 h of milling. The evolution of the phase transformation during the milling time is reported. Increases in milling time produce exponential decrease in the particle size, up to 680 nm after 1 h of milling. After the milling process it is obtained a powder compound with an orthorhombic structure (S.G. Pbnm). A prolonged milling time (>9 h) produce an important reduction in the particle size but this is accompanied with a high iron contamination caused by metallic residues originated from vial and balls and also, after 9 h of milling time, it was found an important distortion in orthorhombic structure, obtaining two types of parameters

Computer modelling of defect structure and rare earth doping in LiCaAlF sub 6 and LiSrAlF sub 6

CERN Document Server

Amaral, J B; Valerio, M E G; Jackson, R A

2003-01-01

This paper describes a computational study of the mixed metal fluorides LiCaAlF sub 6 and LiSrAlF sub 6 , which have potential technological applications when doped with a range of elements, especially those from the rare earth series. Potentials are derived to represent the structure and properties of the undoped materials, then defect properties are calculated, and finally solution energies for rare earth elements are calculated, enabling preferred dopant sites and charge compensation mechanisms to be predicted.

Biocompatibility of 17-4 PH stainless steel foam for implant applications.

Science.gov (United States)

Mutlu, Ilven; Oktay, Enver

2011-01-01

In this study, biocompatibility of 17-4 PH stainless steel foam for biomedical implant applications was investigated. 17-4 PH stainless steel foams having porosities in the range of 40-82% with an average pore size of around 600 μm were produced by space holder-sintering technique. Sintered foams were precipitation hardened for times of 1-6 h at temperatures between 450-570 °C. Compressive yield strength and Young's modulus of aged stainless steel foams were observed to vary between 80-130 MPa and 0.73-1.54 GPa, respectively. Pore morphology, pore size and the mechanical properties of the 17-4 PH stainless steel foams were close to cancellous bone. In vitro evaluations of cytotoxicity of the foams were investigated by XTT and MTT assays and showed sufficient biocompatibility. Surface roughness parameters of the stainless steel foams were also determined to characterize the foams.

High yield and facile microwave-assisted synthesis of conductive H_2SO_4 doped polyanilines

International Nuclear Information System (INIS)

Gizdavic-Nikolaidis, Marija R.; Jevremovic, Milutin M.; Milenkovic, Maja; Allison, Morgan C.; Stanisavljev, Dragomir R.; Bowmaker, Graham A.; Zujovic, Zoran D.

2016-01-01

The microwave-assisted synthesis of polyaniline (PANI) was performed using ammonium persulphate (APS) as oxidizing agent in 0.5 M–2.5 M concentration range of aqueous sulphuric acid (H_2SO_4) at 93 W applied microwave power of 10 min duration. The microwave (MW) synthesized PANIs had 3 times higher yield in comparison to PANI samples prepared using a classical method, CS (0 W MW power) at the same temperature for 10 min synthesis duration period. Fourier Transform Infrared (FTIR) and UV–Vis spectroscopies confirmed the formation of PANI structure in all products. The influence of H_2SO_4 acid dopant on the spin concentration of MW and CS H_2SO_4 doped PANI samples were examined by EPR spectroscopy, while the morphological characteristics were investigated by using scanning electron microscopy (SEM). XRD results showed amorphous phases in both MW and CS H_2SO_4 doped PANI samples. Conductivity measurements revealed ∼1.5 times higher conductivity values for MW H_2SO_4 doped PANI samples in comparison with PANI samples prepared by the CS method under same condition. The influence of sulfate anion in comparison to chloride anion as a dopant on morphological, dopant levels and conductivity properties of MW PANI samples were also investigated. - Highlights: • Nanoporous microwave synthesized doped polyanilines as chemical sensor material. • Morphology and physical properties of polyanilines depend on acid concentration. • Spin concentration is determined by the nature of the polyaniline synthesis.

Luminescence properties and gamma-ray response of the Ce and Ca co-doped (Gd,Y)F3 single crystals

International Nuclear Information System (INIS)

Kamada, Kei; Yanagida, Takayuki; Fujimoto, Yutaka; Fukabori, Akihiro; Yoshikawa, Akira; Nikl, Martin

2011-01-01

The Ca0.5% and Ce1%, 3%, 7%, 10% co-doped Gd 0.5 Y 0.5 F 3 single crystals were grown by the μ-PD method. In the Ca0.5% and Ce3% co-doped sample, Ce 3+ -perturbed luminescence at 380 nm was observed with 32.4 ns photoluminescence decay time. The energy transfer in the sequence of the regular Ce 3+ → (Gd 3+ ) n → the perturbed Ce 3+ sites was evidenced through observation of decay time shortening of the regular Ce 3+ and Gd 3+ centers and the change between the Gd 3+ and Ce 3+ -perturbed emission intensity. The gamma-ray excited scintillation response of the Ca0.5%, Ce7% co-doped Gd 0.5 Y 0.5 F 3 sample was investigated with the help of the pulse height spectra and the light yield, energy resolution and non-proportionality was evaluated in the interval of energies of 59.4-1274 keV.

Optical and structural characterization of the pure and doped BaY2F8 with rare earths for application in radiation detectors and scintillators

International Nuclear Information System (INIS)

Mello, Ana Carolina Santana de

2008-01-01

In this work Barium Yttrium Fluoride (BaY 2 F 8 -BaYF) doped with different concentrations of ions Tb 3+ , Er 3+ , Tm 3+ e Nd 3+ were characterized, aiming the application in radiation detection devices that use the scintillating properties. Two types of samples were produced in the CLA-IPEN-SP, polycrystalline samples, obtained via solid state reaction of BaF 2 and YF 3 under HF atmosphere, and single crystals, obtained via the zone melting method also in a HF atmosphere. The samples were characterized using the following experimental techniques: X-ray powder diffraction, Radioluminescence (RL), Optical Absorption and Dispersive X-ray Absorption Spectroscopy (DXAS). The X-ray diffraction pattern showed the presence of the phase BaY 2 F 8 and a small amount of the phase Ba 4 Y 3 F 17 in the polycrystalline pure and Tb 3+ doped samples. The other samples showed only the desired BaY 2 F 8 phase. The radioluminescence measurements of the doped BaYF, when irradiated with X-rays, showed emission peaks in energies that are characteristics of the 4f-4f transitions of rare earths. The RL of the samples with 2 mol por cent and 3 mold of Tb 3+ showed quite intense peaks with a maximum emission peak at 545 nm. The Tm 3+ doped BYF showed that the scintillation efficiency is not directly proportional to the doping level, and the highest RL emission were obtained for the polycrystalline samples doped with 1 mol por cent, showing a maximum peak intensity at 456 nm (the blue region of the visible spectrum). All samples showed a phosphorescent decay time of the order of seconds. Single crystals of BaYF doped with 2 mol por cent of Er 3+ , in addition to one of the highest phosphorescence time, presents a quite strong Rl in the green region of the spectra. The radiation damage was evaluated by the optical absorption techniques and the results showed that the formation of the absorption bands can be connected to colors centers generated by radiation in the matrix. Measurements of

Indirect Voltammetric Sensing Platforms For Fluoride Detection on Boron-Doped Diamond Electrode Mediated via [FeF6]3− and [CeF6]2− Complexes Formation

International Nuclear Information System (INIS)

Culková, Eva; Tomčík, Peter; Švorc, Ľubomír; Cinková, Kristína; Chomisteková, Zuzana; Durdiak, Jaroslav; Rievaj, Miroslav; Bustin, Dušan

2014-01-01

Very simple and sensitive electroanalytical technique based on synergistic combination of reaction electrochemistry (specificity) and bare boron-doped diamond electrode (sensitivity) for the detection of fluorides in drinking water was developed as variant based on dynamic electrochemistry to ISE analysis. It is based on the formation of electroinactive fluoride complexes with Fe(III) and Ce(IV) ions decreasing such diffusion current of free metal on boron-doped diamond electrode. Due to low background signal of boron-doped diamond electrode reasonably low detection limits of the order of 10 −6 mol L −1 for linear sweep voltammetric method using formation of [FeF 6 ] 3− and 10 −7 mol L −1 in a square-wave variant of this technique have been achieved. This is approximately 1–2 orders lower than in the case of platinum comb-shaped interdigitated microelectrode array. Linear sweep voltammetric method based on [CeF 6 ] 2− complex formation has lower sensitivity and may be suitable for samples with higher content of fluoride and not to analysis of drinking water

Effects of Rare Earth on the Microstructure and Impact Toughness of H13 Steel

OpenAIRE

Gao, Jinzhu; Fu, Paixian; Liu, Hongwei; Li, Dianzhong

2015-01-01

Studies of H13 steel suggest that under appropriate conditions, additions of rare-earth metals (REM) can significantly enhance mechanical properties, such as impact toughness. This improvement is apparently due to the formation of finer and more dispersive RE inclusions and grain refinement after REM additions. In this present work, the microstructure evolution and mechanical properties of H13 steel with rare earth additions (0, 0.015, 0.025 and 0.1 wt.%) were investigated. The grain size, ...

Sigma phases in an 11%Cr ferritic/martensitic steel with the normalized and tempered condition

Energy Technology Data Exchange (ETDEWEB)

Shen, Yinzhong, E-mail: shenyz@sjtu.edu.cn [School of Mechanical Engineering, Shanghai Jiao Tong University, 800 Dongchuan Road, Shanghai 200240 (China); Zhou, Xiaoling; Shi, Tiantian; Huang, Xi [School of Mechanical Engineering, Shanghai Jiao Tong University, 800 Dongchuan Road, Shanghai 200240 (China); Shang, Zhongxia [School of Materials Science and Engineering, Shanghai Jiao Tong University, 800 Dongchuan Road, Shanghai 200240 (China); Liu, Wenwen; Ji, Bo; Xu, Zhiqiang [School of Mechanical Engineering, Shanghai Jiao Tong University, 800 Dongchuan Road, Shanghai 200240 (China)

2016-12-15

At the present time 9–12% Cr ferritic/martensitic (F/M) steels with target operating temperatures up to 650 °C and higher are being developed in order to further increase thermal efficiency so as to reduce coal consumption and air pollution. An 11% Cr F/M steel was prepared by reference to the nominal chemical composition of SAVE12 steel with an expected maximum use temperature of 650 °C. The precipitate phases of the 11% Cr F/M steel normalized at 1050 °C for 0.5 h and tempered at 780 °C for 1.5 h were investigated by transmission electron microscopy. Except for Cr-/Cr-Fe-Co-rich M{sub 23}C{sub 6}, Nb-/V-/Ta-Nb-/Nd-rich MX, Fe-rich M{sub 5}C{sub 2}, Co-rich M{sub 3}C and Fe-Co-rich M{sub 6}C phases previously identified in the steel, two types of sigma phases consisting of σ-FeCr and σ-FeCrW were found to be also present in the normalized and tempered steel. Identified σ-FeCr and σ-FeCrW phases have a simple tetragonal crystal structure with estimated lattice parameters a/c = 0.8713/0.4986 and 0.9119/0.5053 nm, respectively. The compositions in atomic pct of the observed sigma phases were determined to be approximately 50Fe-50Cr for the σ-FeCr, and 30Fe-55Cr-10W in addition to a small amount of Ta, Co and Mn for the σ-FeCrW. The sigma phases in the steel exhibit various blocky morphologies, and appear to have a smaller amount compared with the dominant phases Cr-rich M{sub 23}C{sub 6} and Nb-/V-/Ta-Nb-rich MX of the steel. The σ-FeCr phase in the steel was found to precipitate at δ-ferrite/martensite boundaries, suggesting that δ-ferrite may rapidly induce the formation of sigma phase at δ-ferrite/martensite boundaries in high Cr F/M steels containing δ-ferrite. The formation mechanism of sigma phases in the steel is also discussed in terms of the presence of δ-ferrite, M{sub 23}C{sub 6} precipitation, precipitation/dissolution of M{sub 2}X, and steel composition. - Highlights: •Precipitate phases in normalized and tempered 11%Cr F/M steel are

Color-stable and efficient tandem white organic light-emitting devices using a LiF n-doping layer and a MoO{sub x} p-doping layer as charge generating unit

Energy Technology Data Exchange (ETDEWEB)

Chen, Yu; Wu, Qingyang; Zhang, Zhensong; Yue, Shouzhen; Guo, Runda; Wang, Peng; Wu, Mingzhu; Gou, Changhua; Zhao, Yi, E-mail: yizhao@jlu.edu.cn; Liu, Shiyong

2013-10-31

We have demonstrated color-stable and efficient tandem organic light-emitting devices (OLEDs) using 4,7-diphenyl-1,10-phenanthroline (Bphen):LiF/4,4′,4″-tris(N-3-methylphenyl-N-phenyl-amino)triphenylamine (m-MTDATA):molybdenum oxide (MoO{sub x}) as charge generating unit (CGU), which has the advantages of air stability and ease of fabrication; the working mechanism of Bphen:LiF/m-MTDATA:MoO{sub x} is also discussed through analysis of the electrical and spectral emission properties of tandem devices with different CGUs. The performance of tandem white OLED, comprising blue and yellow phosphorescent EL units, can be improved by optimizing the thickness of Bphen:LiF layer. The device comprised of 30 nm Bphen:LiF layer has a maximum current efficiency of 38.7 cd/A and it can still maintain 24.6 cd/A at the luminance of 10,370 cd/m{sup 2}. Moreover, the Commission Internationale de L'Eclairage (CIE) coordinates of the device are rather stable and the variation is only (± 0.003, ± 0.007) over a wide range of luminance (100–13,000 cd/m{sup 2}). - Highlights: • LiF n-doping layer and MoO{sub x} p-doping layer were used as charge generating units. • The device performance was improved by optimizing the thickness of n-doping layer. • High luminance and efficiency were both achieved at a very low current density. • The device showed rather stable spectra over a wide range of luminance.

VUV and UV–vis optical study on KGd2F7 luminescent host doped with terbium and co-doped with europium

International Nuclear Information System (INIS)

Lisiecki, Radosław

2013-01-01

The KGd 2 F 7 :Tb and KGd 2 F 7 :Tb,Eu samples were obtained using a solid state reaction. Excitation spectra and emission spectra are reported and analyzed within the VUV–UV–vis spectral range. The intense green luminescence is observed in the KGd 2 F 7 :Tb while the combined emission of terbium and europium in the KGd 2 F 7 :Tb,Eu covers substantially the region of white light. The materials under study can be effectively excited making use of intense f–d transitions of Tb 3+ in the VUV–UV region. Experimental lifetimes of luminescent levels have been measured and discussed. It was found that the considerable energy transfer from Tb 3+ to Eu 3+ occurs. -- Highlights: • The prospective green and white emitting phosphors. • The effective VUV and UV–vis excitation process. • The considerable energy transfer among optically active ions. • The influence of (Tb, Eu) co-doping on relaxation dynamic of excited states

Substrate pH and butterfly bush response to dolomitic lime or steel slag amendment

Science.gov (United States)

Steel slag is a fertilizer amendment with a high concentration of calcium oxide, and thus capable of raising substrate pH similar to dolomitic lime. Steel slag, however, contains higher concentrations of some nutrients, such as iron, manganese, and silicon, compared to dolomitic lime. The objectiv...

Synthesis of Ti-doped DLC film on SS304 steels by Filtered Cathodic Vacuum Arc (FCVA) technique for tribological improvement

Science.gov (United States)

Bootkul, D.; Saenphinit, N.; Supsermpol, B.; Aramwit, C.; Intarasiri, S.

2014-08-01

Currently, stainless steels are widely used in various industrial applications due to their excellence in toughness and corrosion resistance. But their resistance to wear needs to be improved for appropriate use in tribological applications. The Filtered Cathodic Vacuum Arc (FCVA) is a superior technique for forming a high-density film structure of amorphous carbon, especially for a tetrahedral amorphous carbon (ta-C) type, because it can produce a plasma of highly energetic ions that can penetrate into a growing coating, resulting in densification of the film. However, this technique tends to generate high internal stress, due to serious accumulation of energy in the film structure that then leads to film delamination. In general, there are numerous solutions that have been used to reduce the internal stress. DLC with various additive elements such as Ti, Cr or W as strong-carbide-forming (SCF) metals is one of the popular methods to provide attractive combinations of properties of wear resistance and film adhesion as well as reducing the internal stress. The present study was focused on investigation of titanium-doped DLC coating on SS304 steel, mainly for adhesion improvement in optimizing for tribological applications. The synthesized films were formed by the FCVA technique at normal substrate temperature. In the experimental set-up, the films were produced by mixing the titanium and carbon ions generated by dual cathode plasma source operating in synchronous pulsed mode. Their compositions were adjusted by varying the relative duration of the pulse length from each cathode. Titanium doping concentration was varied from pure DLC deposition as the control group to titanium and graphite trigger pulses ratios of 1:16, 1:12, 1:10, 1:8 and 1:4, as the Ti-doped DLC group. The results showed that by increasing titanium trigger pulses ratio from 1:16, 1:12, 1:10 and 1:8, respectively, the film adhesion was increased while the wear rate did not change significantly as

White emission materials from glass doped with rare Earth ions: A review

Energy Technology Data Exchange (ETDEWEB)

Yasaka, P.; Kaewkhao, J., E-mail: mink110@hotmail.com [Center of Excellence in Glass Technology and Materials Science (CEGM), Nakhon Pathom Rajabhat University, Nakhon Pathom 73000 (Thailand); Physics Program, Faculty of Science and Technology, Nakhon Pathom Rajabhat University, 73000 (Thailand)

2016-03-11

Solid State Lighting (SSL) based devices are predicted to play a crucial role in the coming years. Development of W-LED, which have an edge over traditional lighting sources due to their compact size, higher reliability, shock resistance, interesting design possibilities, higher transparency and an extremely long lifetime. Over the fifteen trivalent lanthanide ions, Dy{sup 3+} ions doped glasses are most appropriate for white light generation because of the fact that it exhibits two intense emission bands corresponds to the {sup 4}F{sub 9/2}→{sup 6}H{sub 15/2} (magnetic dipole) and {sup 4}F{sub 9/2}→{sup 6}H{sub 13/2} (electric dipole) transitions at around 480-500 nm and 580-600 nm pertaining to blue and yellow regions respectively. In this work, the developments of Dy3+ doped in several glass structures for white emitting materials application have reviewed. Properties of Dy{sup 3+} doped in glasses were discussed for use as a solid state lighting materials application.

Investigation of Eh, pH and corrosion potential of steel in anoxic groundwater

Energy Technology Data Exchange (ETDEWEB)

Peat, R.; Brabon, S.; Fennell, P.A.H.; Rance, A.P.; Smart, N.R. [AEA Technology (United Kingdom)

2001-01-01

SKB intend to dispose of the spent nuclear fuel produced by Sweden's eleven nuclear reactors by encapsulating it in corrosion-resistant copper canisters containing a cast iron or carbon steel insert. After encapsulation, the fuel will be transported to a geological repository, where the containers will be deposited at a depth of 500 to 700 m in granitic rock and surrounded by a bentonite clay backfill material. If, or when the copper corrosion shield fails, the iron insert will be in contact with oxygen-free water and hydrogen-producing, anaerobic corrosion will start. SKB have carried out modelling calculations of the oxidising power (Eh) of groundwater and wished to confirm the results by carrying out experimental measurements. The objective of the work described in this report was to demonstrate the feasibility of monitoring Eh, pH and corrosion potential in a cell where anaerobic corrosion of steel in artificial groundwater was occurring. To this end, gas cells similar to those used previously for anaerobic corrosion rate measurements were used as the basis for the design of an electrochemical cell. The cell incorporated electrodes to provide an in situ measurement of the redox potential, Eh, the pH and the corrosion potential of carbon steel. The main stages of the work were: Design of the electrochemical cell; Preparation of silver-silver chloride and calomel reference electrodes; Calibration of the reference electrodes and commercial glass pH electrodes against a standard hydrogen electrode; Assembly of the test cell under anoxic conditions; Monitoring the cell before and after the addition of steel wires to the test solution. Details of the design of the test cell and the experimental procedures used are described. Two cells were set up. The first employed a silver-silver chloride reference electrode, which was failed after approximately 400 hours, and the second cell therefore used a calomel reference electrode. The results of the electrode

{sup 5}D{sub 3}{yields}{sup 7}F{sub J} emission of Tb doped sol-gel silica

Energy Technology Data Exchange (ETDEWEB)

Seed Ahmed, H.A.A.; Ntwaeaborwa, O.M.; Gusowski, M.A. [Department of Physics, University of the Free State, IB51, Box 339, Bloemfontein 9300 (South Africa); Botha, J.R. [Department of Physics, Nelson Mandela Metropolitan University, Box 77000, Port Elizabeth 6031 (South Africa); Kroon, R.E., E-mail: KroonRE@ufs.ac.za [Department of Physics, University of the Free State, IB51, Box 339, Bloemfontein 9300 (South Africa)

2012-05-15

Amorphous silica samples doped with 0.1 and 1 mol% of terbium (Tb) were synthesized by the sol-gel method. In addition to the green light associated with {sup 5}D{sub 4}{yields}{sup 7}F{sub J} transitions of Tb{sup 3+}, the sample containing 0.1 mol% also emitted blue light as a result of {sup 5}D{sub 3}{yields}{sup 7}F{sub J} transitions during photoluminescence (PL) measurements. As a result of concentration quenching this blue emission was not observed for the samples doped with the higher concentration (1 mol%). However the blue {sup 5}D{sub 3} {yields}{sup 7}F{sub J} emission was observed in the 1 mol% doped samples during cathodoluminescence (CL) measurements. Since a rough calculation indicated that the excitation rate in the CL system where the blue emission is observed may be similar to a laser PL system under conditions where the blue emission is not observed, the difference is attributed to the nature of the excitation sources. It is suggested that during the CL excitation incident electrons can reduce non-luminescent Tb{sup 4+} ions in the silica, substituting for Si{sup 4+} ions, to the excited (Tb{sup 3+}) Low-Asterisk state and that these are responsible for the blue emission, which does not occur during PL excitation.

1887 nm lasing in Tm3+-doped TeO2-BaF2-Y2O3 glass microstructured fibers

Science.gov (United States)

Wang, Shunbin; Yao, Chuanfei; Jia, Zhixu; Qin, Guanshi; Qin, Weiping

2017-04-01

In this paper, we demonstrate ∼2 μm lasing in Tm3+-doped fluorotellurite microstructured fibers. The Tm3+-doped fibers are based on TeO2-BaF2-Y2O3 glasses and fabricated by using a rod-in-tube method. Under the pump of a 1570 nm Er3+-doped fiber laser, lasing at 1887 nm is obtained in a ∼42.5 cm long Tm3+-doped fiber with a threshold pump power of 94 mW. As the pump power increases to 780 mW, the obtained maximum unsaturated power reaches up to ∼408 mW with a slop efficiency of ∼58.1%. This result indicates that the Tm3+-doped fluorotellurite fibers are promising gain media for ∼2 μm fiber lasers.

Passive behaviour of alloy corrosion-resistant steel Cr10Mo1 in simulating concrete pore solutions with different pH

International Nuclear Information System (INIS)

Ai, Zhiyong; Jiang, Jinyang; Sun, Wei; Song, Dan; Ma, Han; Zhang, Jianchun; Wang, Danqian

2016-01-01

Highlights: • A new alloy corrosion-resistant steel Cr10Mo1 is developed for reinforcing rebar of concrete in severe environments. • The effects of pH on the passive behaviour of Cr10Mo1 steel compared with plain carbon steel were studied systematically by electrochemical techniques and surface analysis. • The mechanism for self-reinforcing passivity against carbonation of the corrosion-resistant steel is revealed. - Abstract: The passive behaviour of new alloy corrosion-resistant steel Cr10Mo1 and plain carbon steel (as a comparison) in simulating concrete pore solutions of different pH (ranging from 13.5 to 9.0) under open circuit potential conditions, was evaluated by various electrochemical techniques: potentiodynamic polarization, capacitance measurements and electrochemical impedance spectroscopy. The chemical composition and structure of passive films were investigated by X-ray photoelectron spectroscopy (XPS) and secondary ion mass spectroscopy (SIMS). The electrochemical responses of passive films show that Cr10Mo1 steel has an increasing passivity with pH decreasing while carbon steel dose conversely, revealing carbonation does no negative effect on passivation of the corrosion-resistant steel. SIMS reveals that the passive film on the corrosion-resistant steel presents a bilayer structure: an outer layer mainly consisting of Fe oxides and hydroxides, and an inner layer enriched in Cr species, while only a Fe-concentrated layer for carbon steel. According to the XPS analysis results, as the pH decreases, more stable and protective Cr oxides are enriched in the film on Cr10Mo1 steel while Fe oxides gradually decompose. Higher content of Cr oxides in the film layer provides Cr10Mo1 corrosion-resistant steel more excellent passivity at lower pH.

Passive behaviour of alloy corrosion-resistant steel Cr10Mo1 in simulating concrete pore solutions with different pH

Energy Technology Data Exchange (ETDEWEB)

Ai, Zhiyong, E-mail: 230139452@seu.edu.cn [School of Materials Science and Engineering, Southeast University, Nanjing 211189, Jiangsu (China); Jiangsu Key Laboratory of Construction Materials, Nanjing 211189, Jiangsu (China); Jiang, Jinyang, E-mail: jiangjinyang16@163.com [School of Materials Science and Engineering, Southeast University, Nanjing 211189, Jiangsu (China); Jiangsu Key Laboratory of Construction Materials, Nanjing 211189, Jiangsu (China); Sun, Wei, E-mail: sunwei@seu.edu.cn [School of Materials Science and Engineering, Southeast University, Nanjing 211189, Jiangsu (China); Jiangsu Key Laboratory of Construction Materials, Nanjing 211189, Jiangsu (China); Song, Dan, E-mail: songdancharls@hhu.edu.cn [School of Materials Science and Engineering, Southeast University, Nanjing 211189, Jiangsu (China); Jiangsu Key Laboratory of Construction Materials, Nanjing 211189, Jiangsu (China); College of Mechanics and Materials, Hohai University, Nanjing 210098, Jiangsu (China); Ma, Han, E-mail: mahan-iris@shasteel.cn [Research Institute of Jiangsu Shasteel Iron and Steel, Zhangjiagang 215625, Jiangsu (China); Zhang, Jianchun, E-mail: Zhangjc-iris@shasteel.cn [Research Institute of Jiangsu Shasteel Iron and Steel, Zhangjiagang 215625, Jiangsu (China); Wang, Danqian, E-mail: wonderbaba@126.com [School of Materials Science and Engineering, Southeast University, Nanjing 211189, Jiangsu (China); Jiangsu Key Laboratory of Construction Materials, Nanjing 211189, Jiangsu (China)

2016-12-15

Highlights: • A new alloy corrosion-resistant steel Cr10Mo1 is developed for reinforcing rebar of concrete in severe environments. • The effects of pH on the passive behaviour of Cr10Mo1 steel compared with plain carbon steel were studied systematically by electrochemical techniques and surface analysis. • The mechanism for self-reinforcing passivity against carbonation of the corrosion-resistant steel is revealed. - Abstract: The passive behaviour of new alloy corrosion-resistant steel Cr10Mo1 and plain carbon steel (as a comparison) in simulating concrete pore solutions of different pH (ranging from 13.5 to 9.0) under open circuit potential conditions, was evaluated by various electrochemical techniques: potentiodynamic polarization, capacitance measurements and electrochemical impedance spectroscopy. The chemical composition and structure of passive films were investigated by X-ray photoelectron spectroscopy (XPS) and secondary ion mass spectroscopy (SIMS). The electrochemical responses of passive films show that Cr10Mo1 steel has an increasing passivity with pH decreasing while carbon steel dose conversely, revealing carbonation does no negative effect on passivation of the corrosion-resistant steel. SIMS reveals that the passive film on the corrosion-resistant steel presents a bilayer structure: an outer layer mainly consisting of Fe oxides and hydroxides, and an inner layer enriched in Cr species, while only a Fe-concentrated layer for carbon steel. According to the XPS analysis results, as the pH decreases, more stable and protective Cr oxides are enriched in the film on Cr10Mo1 steel while Fe oxides gradually decompose. Higher content of Cr oxides in the film layer provides Cr10Mo1 corrosion-resistant steel more excellent passivity at lower pH.