WorldWideScience

Sample records for extremely dry conditions

  1. Hyper-dry conditions provide new insights into the cause of extreme floods after wildfire

    Science.gov (United States)

    Moody, John A.; Ebel, Brian A.

    2012-01-01

    A catastrophic wildfire in the foothills of the Rocky Mountains near Boulder, Colorado provided a unique opportunity to investigate soil conditions immediately after a wildfire and before alteration by rainfall. Measurements of near-surface (θ; and matric suction, ψ), rainfall, and wind velocity were started 8 days after the wildfire began. These measurements established that hyper-dryconditions (θ 3 cm-3; ψ > ~ 3 x 105 cm) existed and provided an in-situ retention curve for these conditions. These conditions exacerbate the effects of water repellency (natural and fire-induced) and limit the effectiveness of capillarity and gravity driven infiltration into fire-affected soils. The important consequence is that given hyper-dryconditions, the critical rewetting process before the first rain is restricted to the diffusion–adsorption of water-vapor. This process typically has a time scale of days to weeks (especially when the hydrologic effects of the ash layer are included) that is longer than the typical time scale (minutes to hours) of some rainstorms, such that under hyper-dryconditions essentially no rain infiltrates. The existence of hyper-dryconditions provides insight into why, frequently during the first rain storm after a wildfire, nearly all rainfall becomes runoff causing extremefloods and debris flows.

  2. Cushions of Thylacospermum caespitosum (Caryophyllaceae) do not facilitate other plants under extreme altitude and dry conditions in the north-west Himalayas.

    Science.gov (United States)

    de Bello, Francesco; Doležal, Jiří; Dvorský, Miroslav; Chlumská, Zuzana; Řeháková, Klára; Klimešová, Jitka; Klimeš, Leoš

    2011-09-01

    Cushion plants are commonly considered as keystone nurse species that ameliorate the harsh conditions they inhabit in alpine ecosystems, thus facilitating other species and increasing alpine plant biodiversity. A literature search resulted in 25 key studies showing overwhelming facilitative effects of different cushion plants and hypothesizing greater facilitation with increased environmental severity (i.e. higher altitude and/or lower rainfall). At the same time, emerging ecological theory alongside the cushion-specific literature suggests that facilitation might not always occur under extreme environmental conditions, and especially under high altitude and dryness. To assess these hypotheses, possible nursing effects of Thylacospermum caespitosum (Caryophyllaceae) were examined at extremely high altitude (5900 m a.s.l.) and in dry conditions (precipitation plants were detected. The number and abundance of species were greater outside cushions than within and on the edge of cushions. None of the 13 species detected was positively associated with cushions, while nine of them were negatively associated. Plant diversity increased with the size of the area sampled outside cushions, but no species-area relationship was found within cushions. The results support the emerging theoretical prediction of restricted facilitative effects under extreme combinations of cold and dryness, integrating these ideas in the context of the ecology of cushion plants. This evidence suggests that cases of missing strong facilitation are likely to be found in other extreme alpine conditions.

  3. Detectors in Extreme Conditions

    Energy Technology Data Exchange (ETDEWEB)

    Blaj, G. [SLAC National Accelerator Lab., Menlo Park, CA (United States); Carini, G. [SLAC National Accelerator Lab., Menlo Park, CA (United States); Carron, S. [SLAC National Accelerator Lab., Menlo Park, CA (United States); Haller, G. [SLAC National Accelerator Lab., Menlo Park, CA (United States); Hart, P. [SLAC National Accelerator Lab., Menlo Park, CA (United States); Hasi, J. [SLAC National Accelerator Lab., Menlo Park, CA (United States); Herrmann, S. [SLAC National Accelerator Lab., Menlo Park, CA (United States); Kenney, C. [SLAC National Accelerator Lab., Menlo Park, CA (United States); Segal, J. [SLAC National Accelerator Lab., Menlo Park, CA (United States); Tomada, A. [SLAC National Accelerator Lab., Menlo Park, CA (United States)

    2015-08-06

    Free Electron Lasers opened a new window on imaging the motion of atoms and molecules. At SLAC, FEL experiments are performed at LCLS using 120Hz pulses with 1012 - 1013 photons in 10 femtoseconds (billions of times brighter than the most powerful synchrotrons). This extreme detection environment raises unique challenges, from obvious to surprising. Radiation damage is a constant threat due to accidental exposure to insufficiently attenuated beam, focused beam and formation of ice crystals reflecting the beam onto the detector. Often high power optical lasers are also used (e.g., 25TW), increasing the risk of damage or impeding data acquisition through electromagnetic pulses (EMP). The sample can contaminate the detector surface or even produce shrapnel damage. Some experiments require ultra high vacuum (UHV) with strict design, surface contamination and cooling requirements - also for detectors. The setup is often changed between or during experiments with short turnaround times, risking mechanical and ESD damage, requiring work planning, training of operators and sometimes continuous participation of the LCLS Detector Group in the experiments. The detectors used most often at LCLS are CSPAD cameras for hard x-rays and pnCCDs for soft x-rays.

  4. Survival in Extreme Conditions.

    Science.gov (United States)

    Bloom, Martin; Halsema, James

    1983-01-01

    Explores the psychosocial and environmental configurations involved in the survival of 500 civilians in a Japanese internment camp in the Philippines during World War II. Although conditions were very harsh, the survival rate of this group was better than expected. Discusses available demographic, social organizational, and cultural information.…

  5. Extreme Conditions Modeling Workshop Report

    Energy Technology Data Exchange (ETDEWEB)

    Coe, R. G.; Neary, V. S.; Lawson, M. J.; Yu, Y.; Weber, J.

    2014-07-01

    Sandia National Laboratories (SNL) and the National Renewable Energy Laboratory (NREL) hosted the Wave Energy Converter (WEC) Extreme Conditions Modeling (ECM) Workshop in Albuquerque, NM on May 13th-14th, 2014. The objective of the workshop was to review the current state of knowledge on how to model WECs in extreme conditions (e.g. hurricanes and other large storms) and to suggest how U.S. Department of Energy (DOE) and national laboratory resources could be used to improve ECM methods for the benefit of the wave energy industry.

  6. Extreme conditions (p, T, H)

    Energy Technology Data Exchange (ETDEWEB)

    Mesot, J. [Lab. for Neutron Scattering ETH Zurich, Zurich (Switzerland) and Paul Scherrer Institute, Villigen (Switzerland)

    1996-11-01

    The aim of this paper is to summarize the sample environment which will be accessible at the SINQ. In order to illustrate the type of experiments which will be feasible under extreme conditions of temperature, magnetic field and pressure at the SINQ a few selected examples are also given. (author) 7 figs., 14 refs.

  7. Extreme Conditions Modeling Workshop Report

    Energy Technology Data Exchange (ETDEWEB)

    Coe, Ryan Geoffrey [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Neary, Vincent Sinclair [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Lawon, Michael J. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Yu, Yi-Hsiang [National Renewable Energy Lab. (NREL), Golden, CO (United States); Weber, Jochem [National Renewable Energy Lab. (NREL), Golden, CO (United States)

    2014-07-01

    Sandia National Laboratories (SNL) and the National Renewable Energy Laboratory (NREL) hosted the Wave Energy Converter (WEC) Extreme Conditions Modeling (ECM) Workshop in Albuquerque, New Mexico on May 13–14, 2014. The objective of the workshop was to review the current state of knowledge on how to numerically and experimentally model WECs in extreme conditions (e.g. large ocean storms) and to suggest how national laboratory resources could be used to improve ECM methods for the benefit of the wave energy industry. More than 30 U.S. and European WEC experts from industry, academia, and national research institutes attended the workshop, which consisted of presentations from W EC developers, invited keynote presentations from subject matter experts, breakout sessions, and a final plenary session .

  8. Using dry and wet year hydroclimatic extremes to guide future hydrologic projections

    Science.gov (United States)

    Oni, Stephen; Futter, Martyn; Ledesma, Jose; Teutschbein, Claudia; Buttle, Jim; Laudon, Hjalmar

    2016-07-01

    There are growing numbers of studies on climate change impacts on forest hydrology, but limited attempts have been made to use current hydroclimatic variabilities to constrain projections of future climatic conditions. Here we used historical wet and dry years as a proxy for expected future extreme conditions in a boreal catchment. We showed that runoff could be underestimated by at least 35 % when dry year parameterizations were used for wet year conditions. Uncertainty analysis showed that behavioural parameter sets from wet and dry years separated mainly on precipitation-related parameters and to a lesser extent on parameters related to landscape processes, while uncertainties inherent in climate models (as opposed to differences in calibration or performance metrics) appeared to drive the overall uncertainty in runoff projections under dry and wet hydroclimatic conditions. Hydrologic model calibration for climate impact studies could be based on years that closely approximate anticipated conditions to better constrain uncertainty in projecting extreme conditions in boreal and temperate regions.

  9. Changes in extreme dry and wet precipitation spell

    Science.gov (United States)

    Papalexiou, Simon Michael; Foufoula-Georgiou, Efi; Onof, Chris

    2016-04-01

    Global warming is expected to alter the behavior of hydroclimatic variables in various ways. Therefore, it is of great importance not only to identify which hydroclimatic variables are going through changes but also which of their specific characteristics change and in what way. For example the major focus regarding precipitation has been on changes or trends in extreme events or in annual totals, obviously, not without a reason. Yet one of the aspects of precipitation we believe is of equal importance and has not been extensively studied is extreme dry and wet spells. Changes in dry and wet spells can severely impact all aspects of human lives, ranging from infrastructure planning and water resources management to agriculture and infectious disease spread. In this study we perform an extensive analysis of extreme dry and wet precipitation spells using tenths of thousands of daily precipitation records in order to identify trends or variability changes in the maximum number of consecutive dry or wet days of each year. Our final goal is to evaluate the percentage of stations globally with positive/negative trends either in the mean value or in variability of extreme dry and wet spells and assess if this percentage is statistically justifiable.

  10. Extraordinary survival of nanobacteria under extreme conditions

    Science.gov (United States)

    Bjorklund, Michael; Ciftcioglu, Neva; Kajander, E. Olavi

    1998-07-01

    Nanobacteria show high resistance to gamma irradiation. To further examine their survival in extreme conditions several disinfecting and sterilizing chemicals as well as autoclaving, UV light, microwaves, heating and drying treatments were carried out. The effect of antibiotics used in cell culture were also evaluated. Two forms of nanobacteria were used in the tests: nanobacteria cultured in serum containing medium, and nanobacteria cultured in serum-free medium, the latter being more mineralized. Nanobacteria, having various amounts of apatite on their surfaces, were used to analyze the degree of protection given by the mineral. The chemicals tested included ethanol, glutaraldehyde, formalin, hypochlorite, hydrogen peroxide, hydrochloric acid, sodium hydroxide, detergents, and commercial disinfectants at concentrations generally used for disinfection. After chemical and physical treatments for various times, the nanobacteria were subcultered to detect their survival. The results show unique and wide resistance of nanobacteria to common agents used in disinfection. It can also be seen that the mineralization of the nanobacterial surface furthermore increases the resistance. Survival of nanobacteria is unique among living bacteria, but it can be compared with that observed in spores. Interestingly, nanobacteria have metabolic rate as slow as bacterial spores. A slow metabolic rate and protective structures, like mineral, biofilm and impermeable cell wall, can thus explain the observations made.

  11. Raman spectroscopy under extreme conditions

    Energy Technology Data Exchange (ETDEWEB)

    Goncharov, A F; Crowhurst, J C

    2004-11-05

    We report the results of Raman measurements of various materials under simultaneous conditions of high temperature and high pressure in the diamond anvil cell (DAC). High temperatures are generated by laser heating or internal resistive (ohmic) heating or a combination of both. We present Raman spectra of cubic boron nitride (cBN) to 40 GPa and up to 2300 K that show a continuous pressure and temperature shift of the frequency of the transverse optical mode. We have also obtained high-pressure Raman spectra from a new noble metal nitride, which we synthesized at approximately 50 GPa and 2000 K. We have obtained high-temperature spectra from pure nitrogen to 39 GPa and up to 2000 K, which show the presence of a hot band that has previously been observed in CARS measurements. These measurements have also allowed us to constrain the melting curve and to examine changes in the intramolecular potential with pressure.

  12. Energetic materials at extreme conditions

    Energy Technology Data Exchange (ETDEWEB)

    Millar, David I.A. [Edinburgh Univ. (United Kingdom). EaStCHEM Research School of Chemistry

    2012-07-01

    This thesis describes the high-pressure structural behaviour of a series of energetic compounds that includes the widely used explosive RDX and gas generators such as sodium azide. Using a combination of X-ray and neutron diffraction techniques, crystal structures of these compounds have been obtained under conditions of elevated pressure and temperature. Such studies present significant technical challenges associated with both data collection and analysis, especially for compounds containing conformationally flexible molecules, but the structural information obtained is crucial for enhancing the understanding of the characteristics of energetic materials. Particularly significant is the observation that a high-pressure, high-temperature form of RDX may be recovered to ambient pressure. This has implications for the discovery of new forms of energetic materials that may exhibit enhanced properties, e.g. reduced sensitivity to accidental initiation. The rich high-pressure behaviour of the simple inorganic azides is also noteworthy. All of the six compounds studied in this work were found to undergo at least one phase transition and a total of ten polymorphs have been identified at variable pressure and/or temperature. For example, at high pressure sodium azide adopts the same structure observed for the larger alkali metal azides at atmospheric conditions. The first two chapters of this thesis provide a very accessible introduction to high-pressure research and energetic materials. The subsequent chapters detail the results of these high-pressure studies of energetic materials, demonstrating excellent clarity of expression and highly developed critical analysis. The final chapter points clearly to future opportunities for extending these studies to other energetic materials and for alternative methodologies for their structural modification. (orig.)

  13. Statistical distributions of extreme dry spell in Peninsular Malaysia

    Science.gov (United States)

    Zin, Wan Zawiah Wan; Jemain, Abdul Aziz

    2010-11-01

    Statistical distributions of annual extreme (AE) series and partial duration (PD) series for dry-spell event are analyzed for a database of daily rainfall records of 50 rain-gauge stations in Peninsular Malaysia, with recording period extending from 1975 to 2004. The three-parameter generalized extreme value (GEV) and generalized Pareto (GP) distributions are considered to model both series. In both cases, the parameters of these two distributions are fitted by means of the L-moments method, which provides a robust estimation of them. The goodness-of-fit (GOF) between empirical data and theoretical distributions are then evaluated by means of the L-moment ratio diagram and several goodness-of-fit tests for each of the 50 stations. It is found that for the majority of stations, the AE and PD series are well fitted by the GEV and GP models, respectively. Based on the models that have been identified, we can reasonably predict the risks associated with extreme dry spells for various return periods.

  14. Observed changes in extreme wet and dry spells during the South Asian summer monsoon season

    Science.gov (United States)

    Singh, Deepti; Tsiang, Michael; Rajaratnam, Bala; Diffenbaugh, Noah S.

    2014-06-01

    The South Asian summer monsoon directly affects the lives of more than 1/6th of the world's population. There is substantial variability within the monsoon season, including fluctuations between periods of heavy rainfall (wet spells) and low rainfall (dry spells). These fluctuations can cause extreme wet and dry regional conditions that adversely impact agricultural yields, water resources, infrastructure and human systems. Through a comprehensive statistical analysis of precipitation observations (1951-2011), we show that statistically significant decreases in peak-season precipitation over the core-monsoon region have co-occurred with statistically significant increases in daily-scale precipitation variability. Further, we find statistically significant increases in the frequency of dry spells and intensity of wet spells, and statistically significant decreases in the intensity of dry spells. These changes in extreme wet and dry spell characteristics are supported by increases in convective available potential energy and low-level moisture convergence, along with changes to the large-scale circulation aloft in the atmosphere. The observed changes in wet and dry extremes during the monsoon season are relevant for managing climate-related risks, with particular relevance for water resources, agriculture, disaster preparedness and infrastructure planning.

  15. Conditional simulations for fields of extreme precipitation

    Science.gov (United States)

    Bechler, Aurélien; Vrac, Mathieu; Bel, Liliane

    2014-05-01

    Many environmental models, such as hydrological models, require input data, e.g. precipitation values, correctly simulated and distributed, even at locations where no observation is available. This is particularly true for extreme events that may be of high importance for impact studies. The last decade has seen max-stable processes emerge as a powerful tool for the statistical modeling of spatial extremes. Recently, such processes have been used in climate context to perform simulations at ungauged sites based on empirical distributions of a spatial field conditioned by observed values in some locations. In this work conditional simulations of extremal t process are investigated, taking benefits of its spectral construction. The methodology of conditional simulations proposed by Dombry et al. [2013] for Brown-Resnick and Schlather models is adapted for the extremal t process with some improvements which enlarge the possible number of conditional points. A simulation study enables to highlight the role of the different parameters of the model and to emphasize the importance of the steps of the algorithm. In this work, we focus on the French Mediterranean basin, which is a key spot of occurrences of meteorological extremes such as heavy precipitation. Indeed, major extreme precipitation are regularly observed in this region near the 'cévenol" mountains. The modeling and the understanding of these extreme precipitation - the so-called 'cévenol events" - are of major importance for hydrological studies in this complex terrain since they often trigger major floods in this region. The application of our methodology on real data in this region shows that the model and the algorithm perform well provided the stationary assumptions are fulfilled.

  16. Conditional simulation of extremal Gaussian processes

    CERN Document Server

    Dombry, Clément

    2012-01-01

    Recently the regular conditional distributions of max-infinitely divisible processes were derived by \\citet{Dombry2011} and although these conditional distributions have complicated closed forms, \\citet{Dombry2011b} introduce an algorithm to get conditional realizations of Brown-Resnick processes. In this paper we derive the regular conditional distributions of the max-stable process introduced by \\citet{Schlather2002} and adapt the framework of \\citet{Dombry2011b} to this specific process. We test the methods on simulated data and give an application to extreme temperatures in Switzerland. Results show that the proposed sampling scheme provide accurate conditional simulations and can handle real-sized problems.

  17. QCD under extreme conditions: an informal discussion

    CERN Document Server

    Fraga, E S

    2015-01-01

    We present an informal discussion of some aspects of strong interactions un- der extreme conditions of temperature and density at an elementary level. This summarizes lectures delivered at the 2013 and 2015 CERN – Latin-American Schools of High-Energy Physics and is aimed at students working in experi- mental high-energy physics.

  18. Effect of Extreme Drought on Tropical Dry Forests

    Science.gov (United States)

    Castro, Saulo; Sanchez-Azofeifa, Arturo; Sato, Hiromitsu; Cowling, Sharon; Vega-Araya, Mauricio

    2017-04-01

    Tropical dry forests (TDFs) hold a strong economic and cultural connection to human development in the Neotropics. Historically, TDFs not only represent a source of agricultural and urban land but also an important source of goods and ecosystem services for the communities that live around them. Such is the close connection of TDFs to human activity that they are considered the most heavily utilized and disturbed ecosystem in the world. However, TDF have been largely understudied and represent only a fraction of research devoted to globally tropical ecosystems. Thus we lack the framework to properly project how predicted increases in drought events due to climate change will impact TDFs and human society which depend on its services. Our study aims to show the effect of extreme drought on water, food security, and tropical dry forest productivity in the Guanacaste province of Costa Rica. Two pre-ENSO years (2013-2014) and an ENSO year (2015) were compared. The 2013 and 2014 pre-ENSO years were classified as a normal precipitation (1470 mm) and drought year (1027mm), respectively. The 2015 ENSO year was classified as a severe drought (654mm), with amplified effects resulting by the drought experienced during the previous (2014) growing cycle. Effects of the ENSO drought on agriculture and livestock sectors in the province included losses of US13million and US6.5million, respectively. Crop land losses equaled 2,118 hectares and 11,718 hectares were affected. Hydroelectricity generation decreased by 10% and potable water shortages were observed. The Agriculture and Livestock Ministry (MAG) and the National Emergency Commission (CNE) distributed animal feed and supplies to 4,000 farmers affected by the extreme droughts. Eddy covariance flux measurements were used to identify productivity changes during the extreme drought. Changes in phenologic stages and the transitions between CO2 sink to source during mid-growing cycle were observed. Drought significantly delayed

  19. EFFECT OF DRYING CONDITIONS ON MUSHROOM QUALITY

    Directory of Open Access Journals (Sweden)

    MANOJ KULSHRESHTHA

    2009-03-01

    Full Text Available Fluidized bed drying of mushroom was undertaken to study the drying characteristics and quality of the dried mushrooms. Drying was done at drying air temperatures of 50, 70, and 90oC and air velocities of 1.71 and 2.13 m/s. Two batch sizes, namely, 0.5 kg and 1 kg of sliced milky mushrooms were dried. Drying characteristics and the quality of dried mushrooms were analyzed. The results indicated that the drying time decreased only marginally with increase in air velocity. Drying air temperature of 50oC was better as it resulted in a dried product having better rehydration characteristics, lesser shrinkage and lighter color. Highest energy efficiency (79.74% was observed while drying a batch size of 1 kg at a drying air temperature of 50oC, using an air velocity of 1.7 m/s.

  20. Extreme dry spells: Problem of rounding and Bayesian solution

    Science.gov (United States)

    Cindric Kalin, Ksenija; Pasaric, Zoran

    2016-04-01

    Two theoretically justified models of extremes are applied to dry spell (DS) series: The generalized Pareto distribution is applied to peak-over-threshold data (POT-GP), and the Generalized Extreme Value distribution is applied to the annual maxima (AM-GEV). DS data are categorized according to three precipitation-per-day thresholds (1, 5 and 10 mm). The well-known classical methods for parameter estimation (L-moments and Maximum Likelihood) are applied both to measured and to simulated DS time series. When applied within the GEV model, both methods yield very similar results. Somewhat surprisingly, in the case of the GP model, these methods lead to substantially different estimates of parameters, as well as return values. This is found to be a consequence of the fact that DS values are recorded discretely as a whole number of days, whereas the classical extreme value distributions are intended for continuous data. The inference is further evaluated within the Bayesian paradigm, where the process of rounding can be incorporated in a straightforward manner. The study confirmed precautionary estimations when applying the AM-GEV model in comparison with the simpler AM-Gumbel model. Regarding POT-GP modelling, the Bayesian approach reveals a high uncertainty that can occur in parameter estimations when very high thresholds are considered. It is found that there are no clear criteria in the assessment of some optimal threshold, nor is there a necessity for its detection. Instead, Bayesian inference provides a reasonable overall picture of the range of thresholds compatible with the GP-model. Furthermore, it is concluded that when using rounded data, all three GP parameters should be assessed. The location estimates should be compatible with the theoretical value of 0.5. Although the present study is performed mainly on the DS series from two stations in Croatia spanning the period of 1961-2010, the authors believe that the methodology developed here is applicable to

  1. Pushing precipitation to the extremes in distributed experiments: Recommendations for simulating wet and dry years

    Science.gov (United States)

    Knapp, Alan K.; Avolio, Meghan L.; Beier, Claus; Carroll, Charles J.W.; Collins, Scott L.; Dukes, Jeffrey S.; Fraser, Lauchlan H.; Griffin-Nolan, Robert J.; Hoover, David L.; Jentsch, Anke; Loik, Michael E.; Phillips, Richard P.; Post, Alison K.; Sala, Osvaldo E.; Slette, Ingrid J.; Yahdjian, Laura; Smith, Melinda D.

    2017-01-01

    Intensification of the global hydrological cycle, ranging from larger individual precipitation events to more extreme multiyear droughts, has the potential to cause widespread alterations in ecosystem structure and function. With evidence that the incidence of extreme precipitation years (defined statistically from historical precipitation records) is increasing, there is a clear need to identify ecosystems that are most vulnerable to these changes and understand why some ecosystems are more sensitive to extremes than others. To date, opportunistic studies of naturally occurring extreme precipitation years, combined with results from a relatively small number of experiments, have provided limited mechanistic understanding of differences in ecosystem sensitivity, suggesting that new approaches are needed. Coordinated distributed experiments (CDEs) arrayed across multiple ecosystem types and focused on water can enhance our understanding of differential ecosystem sensitivity to precipitation extremes, but there are many design challenges to overcome (e.g., cost, comparability, standardization). Here, we evaluate contemporary experimental approaches for manipulating precipitation under field conditions to inform the design of ‘Drought-Net’, a relatively low-cost CDE that simulates extreme precipitation years. A common method for imposing both dry and wet years is to alter each ambient precipitation event. We endorse this approach for imposing extreme precipitation years because it simultaneously alters other precipitation characteristics (i.e., event size) consistent with natural precipitation patterns. However, we do not advocate applying identical treatment levels at all sites – a common approach to standardization in CDEs. This is because precipitation variability varies >fivefold globally resulting in a wide range of ecosystem-specific thresholds for defining extreme precipitation years. For CDEs focused on precipitation extremes, treatments should be based

  2. Injuries in an Extreme Conditioning Program.

    Science.gov (United States)

    Aune, Kyle T; Powers, Joseph M

    2016-10-19

    Extreme conditioning programs (ECPs) are fitness training regimens relying on aerobic, plyometric, and resistance training exercises, often with high levels of intensity for a short duration of time. These programs have grown rapidly in popularity in recent years, but science describing the safety profile of these programs is lacking. The rate of injury in the extreme conditioning program is greater than the injury rate of weightlifting and the majority of injuries occur to the shoulder and back. Cross-sectional study. Level 4. This is a retrospective survey of injuries reported by athletes participating in an ECP. An injury survey was sent to 1100 members of Iron Tribe Fitness, a gym franchise with 5 locations across Birmingham, Alabama, that employs exercises consistent with an ECP in this study. An injury was defined as a physical condition resulting from ECP participation that caused the athlete to either seek medical treatment, take time off from exercising, or make modifications to his or her technique to continue. A total of 247 athletes (22%) completed the survey. The majority (57%) of athletes were male (n = 139), and 94% of athletes were white (n = 227). The mean age of athletes was 38.9 years (±8.9 years). Athletes reported participation in the ECP for, on average, 3.6 hours per week (± 1.2 hours). Eighty-five athletes (34%) reported that they had sustained an injury while participating in the ECP. A total of 132 injuries were recorded, yielding an estimated incidence of 2.71 per 1000 hours. The shoulder or upper arm was the most commonly injured body site, accounting for 38 injuries (15% of athletes). Athletes with a previous shoulder injury were 8.1 times as likely to injure their shoulder in the ECP compared with athletes with healthy shoulders. The trunk, back, head, or neck (n = 29, 12%) and the leg or knee (n = 29, 12%) were the second most commonly injured sites. The injury incidence rate among athletes with < 6 months of experience in the ECP

  3. Matter Under Extreme Conditions: The Early Years

    CERN Document Server

    Keeler, R Norris

    2010-01-01

    Extreme conditions in natural flows are examined, starting with a turbulent big bang. A hydro-gravitational-dynamics cosmology model is adopted. Planck-Kerr turbulence instability causes Planck-particle turbulent combustion. Inertial-vortex forces induce a non-turbulent kinetic energy cascade to Planck-Kolmogorov scales where vorticity is produced, overcoming 10^113 Pa Planck-Fortov pressures. The spinning, expanding fireball has a slight deficit of Planck antiparticles. Space and mass-energy powered by gluon viscous stresses expand exponentially at speeds >10^25 c. Turbulent temperature and spin fluctuations fossilize at scales larger than ct, where c is light speed and t is time. Because “dark-energy” antigravity forces vanish when inflation ceases, and because turbulence produces entropy, the universe is closed and will collapse and rebound. Density and spin fossils of big bang turbulent mixing trigger structure formation in the plasma epoch. Fragmenting protosuperclustervoids and protoclustervoi...

  4. Matter Under Extreme Conditions: The Early Years

    Science.gov (United States)

    Keeler, R. Norris; Gibson, Carl H.

    2012-03-01

    Extreme conditions in natural flows are examined, starting with a turbulent big bang. A hydro-gravitational-dynamics cosmology model is adopted. Planck-Kerr turbulence instability causes Planck-particle turbulent combustion. Inertial-vortex forces induce a non-turbulent ki- netic energy cascade to Planck-Kolmogorov scales where vorticity is produced, overcoming 10113 Pa Planck-Fortov pressures. The spinning, expanding fireball has a slight deficit of Planck antiparticles. Space and mass-energy powered by gluon viscous stresses expand exponentially at speeds >1025 c. Turbulent temperature and spin fluctuations fossilize at scales larger than ct, where c is light speed and t is time. Because "dark-energy" antigravity forces vanish when infla- tion ceases, and because turbulence produces entropy, the universe is closed and will collapse and rebound. Density and spin fossils of big bang turbulent mixing trigger structure formation in the plasma epoch. Fragmenting protosuperclustervoids and protoclustervoids produce weak tur- bulence until the plasma-gas transition give chains of protogalaxies with the morphology of tur- bulence. Chain galaxy clusters observed at large redshifts ~8.6 support this interpretation. Pro- togalaxies fragment into clumps, each with a trillion Earth-mass H-He gas planets. These make stars, supernovae, the first chemicals, the first oceans and the first life soon after the cosmologi- cal event.

  5. Role of Anomalous States of Upper Tropospheric Circulation on Extremely Dry and Wet Summer Monsoon Events

    Science.gov (United States)

    Ahmad, S.; Koike, T.; Nishii, K.; Shrestha, M.

    2011-12-01

    Seasonal changes in wind pattern, monsoon, sometimes result in severe droughts and intense flooding in many parts of the world including South Asian countries like Pakistan. The livelihood of a vast population in Pakistan depends on agriculture and land use is strongly influenced by water-based ecosystems that depend on the monsoon rains. Furthermore, climate change studies undertaken so far reveal that action is essential in order to prevent long term damage to water cycle and thus of great concern to the community and stakeholders. Pakistan Summer Monsoon (PSM) is affected by both the disturbances from the tropical and the extratropical regions; however there is lack of understanding of physical mechanisms of PSM compared to other regional studies i.e. Indian Summer Monsoon (ISM) and South-East Asian Monsoon (SEAM). In our study, we applied heat and vorticity budgets, and wave train analysis to reveal the mechanisms of the extremely dry and wet PSM events associated with the anomalous upper tropospheric conditions. We found that the extremely dry (wet) PSM events were closely related with the anomalous cyclonic (anticyclonic) upper-tropospheric circulation around northwest of Pakistan, and mid-upper tropospheric cooling (warming) anomaly around Pakistan and to its north/northwest. We also found in addition to Rossby wave response due to the suppressed (enhanced) convective activities around monsoon regions, the midlatitude wave energy propagation emanating around cyclonic/anticyclonic anomaly around northwestern Atlantic, northeastern Atlantic, Europe or Mediterranean regions induced/reinforced/maintained the anomalous upper tropospheric cyclonic (anticyclonic) circulation around northwest of Pakistan during extremely dry (wet) PSM events. Therefore, devastating drought (flood) events over the PSM region resulting from weak (strong) convection anomalies are induced by both the tropical and extratropical processes.

  6. Community responses to extreme climatic conditions

    Directory of Open Access Journals (Sweden)

    Frédéric JIGUET, Lluis BROTONS, Vincent DEVICTOR

    2011-06-01

    Full Text Available Species assemblages and natural communities are increasingly impacted by changes in the frequency and severity of extreme climatic events. Here we propose a brief overview of expected and demonstrated direct and indirect impacts of extreme events on animal communities. We show that differential impacts on basic biological parameters of individual species can lead to strong changes in community composition and structure with the potential to considerably modify the functional traits of the community. Sudden disequilibria have even been shown to induce irreversible shifts in marine ecosystems, while cascade effects on various taxonomic groups have been highlighted in Mediterranean forests. Indirect effects of extreme climatic events are expected when event-induced habitat changes (e.g. soil stability, vegetation composition, water flows altered by droughts, floods or hurricanes have differential consequences on species assembled within the communities. Moreover, in increasing the amplitude of trophic mismatches, extreme events are likely to turn many systems into ecological traps under climate change. Finally, we propose a focus on the potential impacts of an extreme heat wave on local assemblages as an empirical case study, analysing monitoring data on breeding birds collected in France. In this example, we show that despite specific populations were differently affected by local temperature anomalies, communities seem to be unaffected by a sudden heat wave. These results suggest that communities are tracking climate change at the highest possible rate [Current Zoology 57 (3: 406–413, 2011].

  7. Community responses to extreme climatic conditions

    Institute of Scientific and Technical Information of China (English)

    Frédéric JIGUET; Lluis BROTONS; Vincent DEVICTOR

    2011-01-01

    Species assemblages and natural communities are increasingly impacted by changes in the frequency and severity of extreme climatic events. Here we propose a brief overview of expected and demonstrated direct and indirect impacts of extreme events on animal communities. We show that differential impacts on basic biological parameters of individual species can lead to strong changes in community composition and structure with the potential to considerably modify the functional traits of the community. Sudden disequilibria have even been shown to induce irreversible shifts in marine ecosystems, while cascade effects on various taxonomic groups have been highlighted in Mediterranean forests. Indirect effects of extreme climatic events are expected when event-induced habitat changes (e.g. Soil stability, vegetation composition, water flows altered by droughts, floods or hurricanes) have differential consequences on species assembled within the communities. Moreover, in increasing the amplitude of trophic mismatches, extreme events are likely to turn many systems into ecological traps under climate change. Finally, we propose a focus on the potential impacts of an extreme heat wave on local assemblages as an empirical case study, analysing monitoring data on breeding birds collected in France. In this example, we show that despite specific populations were differently affected by local temperature anomalies, communities seem to be unaffected by a sudden heat wave. These results suggest that communities are tracking climate change at the highest possible rate.

  8. SLOPE LITHOLOGIC PROPERTY, SOIL MOISTURE CONDITION AND REVEGETATION IN DRY-HOT VALLEY OF JINSHA RIVER

    Institute of Scientific and Technical Information of China (English)

    XIONG Dong-hong; ZHOU Hong-yi; YANG Zhong; ZHANG Xin-bao

    2005-01-01

    The dry-hot valley of the Jinsha River is one of the typical eco-fragile areas in Southwest China, as well as a focus ofrevegetation study in the upper and middle reaches of the Changjiang River. Due to its extremely dry and hot climate, severely degraded vegetation and the intense soil and water loss, there are extreme difficulties in vegetation restoration in this area and no great breakthrough has ever been achieved on studies of revegetation over the last several decades. Through over ten years' research conducted in the typical areas-the Yuanmou dry-hot valley, the authors found that the lithologic property is one of the crucial factors determining soil moisture conditions and vegetation types in the dry-hot valley, and the rainfall infiltration capability is also one of the key factors affecting the tree growth. Then the revegetation zoning based on different slopes was conducted and revegetation patterns for different zones were proposed.

  9. Crenarchaeal biofilm formation under extreme conditions.

    Directory of Open Access Journals (Sweden)

    Andrea Koerdt

    Full Text Available BACKGROUND: Biofilm formation has been studied in much detail for a variety of bacterial species, as it plays a major role in the pathogenicity of bacteria. However, only limited information is available for the development of archaeal communities that are frequently found in many natural environments. METHODOLOGY: We have analyzed biofilm formation in three closely related hyperthermophilic crenarchaeotes: Sulfolobus acidocaldarius, S. solfataricus and S. tokodaii. We established a microtitre plate assay adapted to high temperatures to determine how pH and temperature influence biofilm formation in these organisms. Biofilm analysis by confocal laser scanning microscopy demonstrated that the three strains form very different communities ranging from simple carpet-like structures in S. solfataricus to high density tower-like structures in S. acidocaldarius in static systems. Lectin staining indicated that all three strains produced extracellular polysaccharides containing glucose, galactose, mannose and N-acetylglucosamine once biofilm formation was initiated. While flagella mutants had no phenotype in two days old static biofilms of S. solfataricus, a UV-induced pili deletion mutant showed decreased attachment of cells. CONCLUSION: The study gives first insights into formation and development of crenarchaeal biofilms in extreme environments.

  10. More extreme precipitation in the world’s dry and wet regions

    Science.gov (United States)

    Donat, Markus G.; Lowry, Andrew L.; Alexander, Lisa V.; O'Gorman, Paul A.; Maher, Nicola

    2016-05-01

    Intensification of the hydrological cycle is expected to accompany a warming climate. It has been suggested that changes in the spatial distribution of precipitation will amplify differences between dry and wet regions, but this has been disputed for changes over land. Furthermore, precipitation changes may differ not only between regions but also between different aspects of precipitation, such as totals and extremes. Here we investigate changes in these two aspects in the world’s dry and wet regions using observations and global climate models. Despite uncertainties in total precipitation changes, extreme daily precipitation averaged over both dry and wet regimes shows robust increases in both observations and climate models over the past six decades. Climate projections for the rest of the century show continued intensification of daily precipitation extremes. Increases in total and extreme precipitation in dry regions are linearly related to the model-specific global temperature change, so that the spread in projected global warming partly explains the spread in precipitation intensification in these regions by the late twenty-first century. This intensification has implications for the risk of flooding as the climate warms, particularly for the world’s dry regions.

  11. Observational Simulation of Icing in Extreme Weather Conditions

    Science.gov (United States)

    Gultepe, Ismail; Heymsfield, Andrew; Agelin-Chaab, Martin; Komar, John; Elfstrom, Garry; Baumgardner, Darrel

    2017-04-01

    Observations and prediction of icing in extreme weather conditions are important for aviation, transportation, and shipping applications, and icing adversely affects the economy. Icing environments can be studied either in the outdoor atmosphere or in the laboratory. There have been several aircraft based in-situ studies related to weather conditions affecting aviation operations, transportation, and marine shipping that includes icing, wind, and turbulence. However, studying severe weather conditions from aircraft observations are limited due to safety and sampling issues, instrumental uncertainties, and even the possibility of aircraft producing its own physical and dynamical effects. Remote sensing based techniques (e.g. retrieval techniques) for studying severe weather conditions represent usually a volume that cannot characterize the important scales and also represents indirect observations. Therefore, laboratory simulations of atmospheric processes can help us better understand the interactions among microphysical and dynamical processes. The Climatic Wind Tunnel (CWT) in ACE at the University of Ontario Institute of Technology (UOIT) has a large semi-open jet test chamber with flow area 7-13 m2 that can precisely control temperatures down to -40°C, and up to 250 km hr-1 wind speeds, for heavy or dry snow conditions with low visibility, similar to ones observed in the Arctic and cold climate regions, or at high altitude aeronautical conditions. In this study, the ACE CWT employed a spray nozzle array suspended in its settling chamber and fed by pressurized water, creating various particle sizes from a few microns up to mm size range. This array, together with cold temperature and high wind speed, enabled simulation of severe weather conditions, including icing, visibility, strong wind and turbulence, ice fog and frost, freezing fog, heavy snow and blizzard conditions. In this study, the test results will be summarized, and their application to aircraft

  12. Effective interactions for extreme isospin conditions; Interactions effectives pour des conditions extremes d`isospin

    Energy Technology Data Exchange (ETDEWEB)

    Chabanat, E.

    1995-01-01

    One of the main goal in nuclear physics research is the study of nuclei in extreme conditions of spin and isospin. The more performing tools for theoretical predictions in this field are microscopic methods such as the Hartree-Fock one based on independent particle approximation. The main ingredient for such an approach is the effective nucleon-nucleon interaction. The actual trend being the study of nuclei more and more far from the stability valley, it is necessary to cast doubt over the validity of usual effective interaction. This work constitute a study on the way one can construct a new interaction allowing some theoretical predictions on nuclei far from the stability. We have thus made a complete study of symmetric infinite nuclear matter and asymmetric one up to pure neutron matter. One shows that the asymmetry coefficient, which was considered until now as fixing isospin properties, is not sufficient to have a correct description of very exotic isospin states. A new type of constraint is shown for fixing this degree of freedom: the neutron matter equation of state. One include this equation of state, taken from a theoretical model giving a good description of radii and masses of neutron stars. One can thus expect to build up new Skyrme interaction with realistic properties of ground state of very neutron-rich nuclei. (author). 63 refs., 68 figs., 15 tabs.

  13. [Guidelines on asthma in extreme environmental conditions].

    Science.gov (United States)

    Drobnic, Franchek; Borderías Clau, Luis

    2009-01-01

    Asthma is a highly prevalent chronic disease which, if not properly controlled, can limit the patient's activities and lifestyle. In recent decades, owing to the diffusion of educational materials, the application of clinical guidelines and, most importantly, the availability of effective pharmacological treatment, most patients with asthma are now able to lead normal lives. Significant social changes have also taken place during the same period, including more widespread pursuit of sporting activities and tourism. As a result of these changes, individuals with asthma can now participate in certain activities that were inconceivable for these patients only a few years ago, including winter sports, underwater activities, air flight, and travel to remote places with unusual environmental conditions (deserts, high mountain environments, and tropical regions). In spite of the publication of several studies on this subject, our understanding of the effects of these situations on patients with asthma is still limited. The Spanish Society of Pulmonology and Thoracic Surgery (SEPAR) has decided to publish these recommendations based on the available evidence and expert opinion in order to provide information on this topic to both doctors and patients and to avert potentially dangerous situations that could endanger the lives of these patients.

  14. Changing characteristics of extreme wet and dry spells of Indian monsoon rainfall

    Science.gov (United States)

    Vinnarasi, R.; Dhanya, C. T.

    2016-03-01

    Modeling of extreme events and its dynamic behavior have always been an intriguing topic. Increase in the magnitude and frequency of extreme events has widely been reported in recent decades, which is attributed to abrupt changes in climate. Numerous studies on extreme Indian monsoon characteristics, using a coarse-resolution data set, have pointed out significant changes in heavy precipitation pattern over India. However, these studies differ in their conclusions, emphasizing the need for a fine-resolution analysis. The present study aims to analyze the spatiotemporal variations and trends in the extreme (wet and dry) Indian monsoon precipitation, using 0.25° × 0.25° high-resolution gridded data for a period of 113 years (1901-2013). Significant increase in the maximum intensity of rainfall and spatial heterogeneity is observed over the past half century. In addition, significant negative trends in wet spell durations and positive trends in dry spell durations are observed over wet regions; whereas contrasting trends are observed over dry regions. A shift in the frequency distribution of extreme events during the monsoon period is also noticed. The 50 year return level of maximum intensity clearly shows positive trends over the past century. Though characteristics of extremes are observed to be highly localized, apparent signs of wet regions turning drier and dry regions turning wetter are obtained. A comprehensive insight into different characteristics (intensity, spell, onset, and frequency) of Indian monsoon extremes is provided, which will help in effective water resources management and flood/drought hazard preparedness.

  15. Diagnosing the Nature of Land-Atmosphere Coupling: A Case Study of Dry/Wet Extremes

    Science.gov (United States)

    Santanello, Joseph A., Jr.; Peters-Lidard, Christa; Kennedy, Aaron D.

    2012-01-01

    Land-atmosphere (L-A) interactions play a critical role in determining the diurnal evolution of land surface and planetary boundary layer (PBL) temperature and moisture states and fluxes. In turn, these interactions regulate the strength of the connection between surface moisture and precipitation in a coupled system. To address deficiencies in numerical weather prediction and climate models due to improper treatment of L-A interactions, recent studies have focused on development of diagnostics to quantify the strength and accuracy of the land-PBL coupling at the process-level. In this study, a diagnosis of the nature and impacts oflocalland-atmosphere coupling (LoCo) during dry and wet extreme conditions is presented using a combination of models and observations during the summers of2006-7 in the U.S. Southern Great Plains. Specifically, the Weather Research and Forecasting (WRF) model has been coupled to NASA's Land Information System (LIS), which provides a flexible and high-resolution representation and initialization of land surface physics and states. A range of diagnostics exploring the links and feedbacks between soil moisture and precipitation are examined for the dry/wet regimes of this region, along with the behavior and accuracy of different land-PBL scheme couplings under these conditions. In addition, we examine the impact of improved specification ofland surface states, anomalies, and fluxes that are obtained through the use of a hew optimization and uncertainty module in LIS, on the L-A coupling in WRF forecasts. Results demonstrate how LoCo diagnostics can be applied to coupled model components in the context of their integrated impacts on the process-chain connecting the land surface to the PBL and support of hydrological anomalies.

  16. Analysis of drying potato kinetics in laboratory conditions

    Directory of Open Access Journals (Sweden)

    Zlatković B.P.

    2005-01-01

    Full Text Available Chemistry is in its nature a fundamental science, but nowadays its results are increasingly used in practice. In such a way, many syntheses of important nutrition and industrial compounds (chemical technology, or destruction of harmful substances (chemical ecology have been developed. The analytic part of chemistry (analytical chemistry has found a significant usage even in optimization of technological processes of food technology. One of the oldest ways of food preservation is drying (dehydration. The basis of this process of preservation is to vaporize water, to dry enough the product, in order to stop the activity of enzymes and possibility of microorganisms’ development. Water in agricultural products is not free but bound to dry matter. Therefore, for its vaporizing it is necessary to bring enough heat. The part of the brought heat is used for vaporizing water, but one part of it becomes the energy for activation of several chemical reactions that decrease the nutritive values and the quality of future food. Therefore, the important engineering problem emerges: determination of optimal conditions for drying. For optimization of technological process of drying, it is necessary to do mathematical modeling of dependence of water vaporizing speed from environmental conditions beforehand. The aim of this paper is to determine potato pieces drying kinetics in laboratory dryer, in order to determine the optimal conditions for its industrial dehydration. It was established that in the first quarter of the time of drying evaporated 28.3% of total evaporation of water, and then in order by quarters: 53%, 14.1% and 4.6%, respectively. The greatest speed of drying was realized at moisture of potatoes about 50%.

  17. Adzuki beans (Vigna angularis seed quality under several drying conditions

    Directory of Open Access Journals (Sweden)

    Osvaldo Resende

    2012-03-01

    Full Text Available This study analyzed the drying process and the seed quality of adzuki beans (Vigna angularis. Grains of adzuki beans, with moisture content of 1.14 (decimal dry basis at harvest and dried until the moisture content of 0.11 (decimal dry basis. were used. Drying was done in an experimental drier maintened at controlled temperatures of 30, 40, 50, 60, and 70 ºC and relative humidity of 52.0, 28.0, 19.1, 13.1, and 6.8%, respectively. Physiological and technological seed quality was evaluated using the germination test, Index of Germination Velocity (IGV, electrical conductivity, and water absorption, respectively. Under the conditions tested in the present study, it can be concluded that drying time for adzuki beans decreases with the higher air temperatures of 60 and 70 ºC, and it affected the physiological and technological seed quality. Thus, to avoid compromising adzuki seeds quality, it is recommended to promote its drying up to 50 ºC.

  18. Effect of Drying Operating Conditions on Canola Oil Tocopherol Content

    Directory of Open Access Journals (Sweden)

    Daniela Laoretani

    2014-03-01

    Full Text Available The aim of this work was to evaluate two operating parameters of seed drying (temperature and initial moisture content on the tocopherol content of canola oil. The raw material was characterized by moisture, oil, protein, crude fiber and ash content. Seeds at 13.6% and 22.7% moisture content (dry basis, db were dried at temperatures in the range of 35–100 °C to a safe storage moisture of 7% db. Oil was extracted from each treated sample. The oil extracted from the samples dried at the extreme temperatures was analyzed by means of the acidity value, peroxide index and fatty acid composition, finding no significant differences among treatments or among untreated and treated samples. Tocopherol contents in the oils obtained for all the assayed temperatures were determined. Differences were found for the samples with 22.7% (db initial moisture content. Except at 35 °C, temperature affected negatively the oil tocopherol content. However, when 13.6% (db moisture seeds were processed, no significant differences were observed in the amount of this minor oil component among assays.

  19. Dynamic characterization of the cutting conditions in dry turning

    Energy Technology Data Exchange (ETDEWEB)

    Serra, R [ENI Val de Loire, Universite Francois Rabelais de Tours, Laboratoire de Mecanique et Rheologie, E.A. 2640, B.P. 3410, 41034 Blois Cedex (France); Chibane, H [Universite Francois Rabelais, Laboratoire de Mecanique et Rheologie, E.A. 2640, B.P. 3410, 41034 Blois Cedex (France); Leroy, R, E-mail: roger.serra@univ-tours.f [Universite Francois Rabelais, Polytech' Tours, Laboratoire de Mecanique et Rheologie, E.A. 2640, 7 Avenue Marcel Dassault, 37200 Tours (France)

    2009-08-01

    Machining instability in the form of violent vibrations or chatter is a physical process characterized by extreme cutting force at the cutting point. The process has very negative impact on machine integrity, tool life, surface quality and dimensional accuracy. Thus it could significantly compromise productivity and manufacturing quality. In the present paper, the importance of characterization and identification of dynamic instability in dry turning operation are shown. The stability behaviour of machine vibration or chatter has been examined and the various relevant parameters are studied and discuted. For chatter detection and identification of the transition between stable and unstable states, different methods are used. Results obtained proof the accuracy of these methods.

  20. Effect of moderate spray drying conditions on functionality of dried egg white and whole egg.

    Science.gov (United States)

    Ayadi, M A; Khemakhem, M; Belgith, H; Attia, H

    2008-08-01

    Dried egg and egg-derived proteins have a range of applications in baking, dressings, and confectionery products. Egg powder was produced under high time-temperature scales (approximately 160 degrees C), which led to many changes in egg components, resulting in different functional properties of eggs after reconstitution. In this study, moderate operating conditions were selected to dry egg white and whole egg using a pilot-scale spray dryer. Functional properties changes were evaluated with an appropriate statistical technique. Major finding supports that spray drying of egg white at moderate conditions (air inlet temperature ranged from 110 to 125 degrees C) resulted in a product that enhanced considerably the water holding capacity of produced gels. Moreover, gel prepared with the dried samples was firmer than that of the fresh samples. Drying at a moderate scale allowed not only the increasing of the foaming capacity and the stability of foam but also an increase in their emulsifying capacity and stability of the emulsions.

  1. Association of joint occurrence of warm and dry conditions over Greece with anticyclonic activity during summer

    Science.gov (United States)

    Hatzaki, Maria; Nastos, Panagiotis; Polychroni, Iliana; Flocas, Helena A.; Kouroutzoglou, John; Dalezios, Nicolas R.

    2016-04-01

    Anticyclones are often associated with extreme phenomena, like prolonged droughts or heatwaves and, thus, they can significantly impact fauna and flora, water resources and public health. In this study, the association of the summer anticyclonic activity with the joint occurrence of extreme warm and dry conditions over Greece is explored. The warm and dry extreme conditions are defined by utilizing the Warm/Dry (WD) index for representative meteorological stations from sub-regions of Greece with different climatic features. The WD index is the number of days over a period (here summer) having at the same time mean air temperature > 75th percentile of daily mean temperature and precipitation University of Melbourne (MS scheme), using the ERA-Interim mean sea-level pressure fields for 1979-2012. The examination of inter-annual and spatial variations of the WD index in association with shifts of the anticyclonic maxima shows that the different sub-regions of Greece are not affected evenly, stressing the role of the complex topography of the region and the variations in the subtropical jet position.

  2. The Extreme Conditions Beamline P02.2 and the Extreme Conditions Science Infrastructure at PETRA III

    Energy Technology Data Exchange (ETDEWEB)

    Liermann, H.-P., E-mail: hanns-peter.liermann@desy.de; Konôpková, Z. [Deutsches Elektronen-Synchrotron (DESY), Hamburg (Germany); Morgenroth, W. [University of Frankfurt, Frankfurt (Germany); Glazyrin, K.; Bednarčik, J.; McBride, E. E. [Deutsches Elektronen-Synchrotron (DESY), Hamburg (Germany); Petitgirard, S. [Deutsches Elektronen-Synchrotron (DESY), Hamburg (Germany); University of Bayreuth, Bayreuth (Germany); Delitz, J. T.; Wendt, M.; Bican, Y.; Ehnes, A.; Schwark, I.; Rothkirch, A.; Tischer, M.; Heuer, J.; Schulte-Schrepping, H.; Kracht, T.; Franz, H. [Deutsches Elektronen-Synchrotron (DESY), Hamburg (Germany)

    2015-06-19

    Performance description of the Extreme Conditions Beamline (ECB, P02.2) at PETRA III that is optimized for micro-diffraction at simultaneous high pressure and high and low temperatures created in different diamond anvil cells environments. Additional information of the capabilities of the Extreme Conditions Science Infrastructure for DAC work is provided. A detailed description is presented of the Extreme Conditions Beamline P02.2 for micro X-ray diffraction studies of matter at simultaneous high pressure and high/low temperatures at PETRA III, in Hamburg, Germany. This includes performance of the X-ray optics and instrumental resolution as well as an overview of the different sample environments available for high-pressure studies in the diamond anvil cell. Particularly emphasized are the high-brilliance and high-energy X-ray diffraction capabilities of the beamline in conjunction with the use of fast area detectors to conduct time-resolved compression studies in the millisecond time regime. Finally, the current capability of the Extreme Conditions Science Infrastructure to support high-pressure research at the Extreme Conditions Beamline and other PETRA III beamlines is described.

  3. Response of Simple, Model Systems to Extreme Conditions

    Energy Technology Data Exchange (ETDEWEB)

    Ewing, Rodney C. [Univ. of Michigan, Ann Arbor, MI (United States); Lang, Maik [Univ. of Michigan, Ann Arbor, MI (United States)

    2015-07-30

    The focus of the research was on the application of high-pressure/high-temperature techniques, together with intense energetic ion beams, to the study of the behavior of simple oxide systems (e.g., SiO2, GeO2, CeO2, TiO2, HfO2, SnO2, ZnO and ZrO2) under extreme conditions. These simple stoichiometries provide unique model systems for the analysis of structural responses to pressure up to and above 1 Mbar, temperatures of up to several thousands of kelvin, and the extreme energy density generated by energetic heavy ions (tens of keV/atom). The investigations included systematic studies of radiation- and pressure-induced amorphization of high P-T polymorphs. By studying the response of simple stoichiometries that have multiple structural “outcomes”, we have established the basic knowledge required for the prediction of the response of more complex structures to extreme conditions. We especially focused on the amorphous state and characterized the different non-crystalline structure-types that result from the interplay of radiation and pressure. For such experiments, we made use of recent technological developments, such as the perforated diamond-anvil cell and in situ investigation using synchrotron x-ray sources. We have been particularly interested in using extreme pressures to alter the electronic structure of a solid prior to irradiation. We expected that the effects of modified band structure would be evident in the track structure and morphology, information which is much needed to describe theoretically the fundamental physics of track-formation. Finally, we investigated the behavior of different simple-oxide, composite nanomaterials (e.g., uncoated nanoparticles vs. core/shell systems) under coupled, extreme conditions. This provided insight into surface and boundary effects on phase stability under extreme conditions.

  4. Drying kinetics and physico-chemical characteristics of Osmo- dehydrated Mango, Guava and Aonla under different drying conditions.

    Science.gov (United States)

    Kumar, P Suresh; Sagar, V R

    2014-08-01

    Mango (Mangiferra indica L), guava (Psiduim guajava L.) slices and aonla (Emblica officinalis L) segments were osmo-dried under four different dying conditions viz., cabinet drier (CD), vacuum oven drier (VOD), low temperature drier (LTD) and solar drier (SD) to evaluate the best drying condition for the fruits. It was found that vacuum oven drying was superior to other mode of drying as it holds maximum nutrients like acidity, ascorbic acid, sugar and water removal and moisture ratio of products. It was found through regression analysis that drying ratio and rehydration ratio was also superior in vacuum drying followed by cabinet drying. In addition, descriptive analysis on sensory score was also found best with vacuum drying while the Non-enzymatic browning (NEB), which is undesirable character on dried product, was more with solar drier.

  5. Directional analysis of extreme winds under mixed climate conditions

    CSIR Research Space (South Africa)

    Kruger, A

    2013-07-01

    Full Text Available -1 European-African Conference on Wind Engineering 2013, Robinson College, Cambridge, July 2013 Directional Analysis of Extreme Winds under Mixed Climate Conditions *Andries Kruger1, Adam Goliger2 and Johan Retief3 1Climate Service, South African...

  6. Host-parasite interactions under extreme climatic conditions

    Institute of Scientific and Technical Information of China (English)

    J. MARTINEZ; S. MERINO

    2011-01-01

    The effect that climatic changes can exert on parasitic interactions represents a multifactor problem whose results are difficult to predict. The actual impact of changes will depend on their magnitude and the physiological tolerance of affected organisms. When the change is considered extreme (I.e. Unusual weather events that are at the extremes of the historical distribution for a given area), the probability of an alteration in an organisms' homeostasis increases dramatically. However, factors determining the altered dynamics of host-parasite interactions due to an extreme change are the same as those acting in response to changes of lower magnitude. Only a deep knowledge of these factors will help to produce more accurate predictive models for the effects of extreme changes on parasitic interactions. Extreme environmental conditions may affect pathogens directly when they include free-living stages in their life-cycles and indirectly through reduced resource availability for hosts and thus reduced ability to produce efficient anti-parasite defenses, or by effects on host density affecting transmission dynamics of diseases or the frequency of intraspecific contact. What are the consequences for host-parasite interactions? Here we summarize the present knowledge on three principal factors in determining host-parasite associations; biodiversity, population density and immunocompetence. In addition, we analyzed examples of the effects of environmental alteration of anthropogenic origin on parasitic systems because the effects are analogous to that exerted by an extreme climatic change.

  7. Dry heat microbial reduction at various humidity conditions

    Science.gov (United States)

    Haberer, Klaus; Schuehlein, Karl-Heinz

    In accordance with interplanetary protection requirements space-craft intended to land on other planets must be of high microbiological purity. High temperatures and long exposure times are needed, to sufficiently treat space craft materials with dry heat. Humidity has been reported to have a major influence on dry heat inactivation of microorganisms. Data obtained in the 1970es show, that dry heat sterilization lethality in the temperature range 104C to 125C increased significantly if environmental humidity during treatment was lowered. However, lethality of the process might no longer be affected by humidity at temperatures under 125C. In order to expand the available body of data, an equipment for simultaneous exposure of multiple inoculated coupons under controlled ambient temperature conditions has been designed. The thermal exposure concept is based on constant heat radiation from an insulated heating block. Exposure chambers are continuously flushed by a pre-heated stream of air of controlled absolute humidity. The systems allows for rapid heating of steel carriers loaded with a defined number of bacterial spores. Relative sterilization effectiveness under changing exposure conditions including heat-up and cool down phases was determined, based on temperature profiles. Parallel exposure of 20 replicate carriers allowed for statistical analysis of the kill time by evaluation of the number of samples showing growth / no growth (fraction negative analysis). Experiments performed at temperatures between 120C and 200C at 5 absolute humidity conditions between 0.1 and 10 g/m of air showed no clear influence of absolute humidity. Pre-equilibration of the spores at relative humidity levels of 15, 48, and 85 percent showed higher sensitivity of the spores pre-incubated under dry conditions.

  8. Optimization on drying conditions of a solar electrohydrodynamic drying system based on desirability concept.

    Science.gov (United States)

    Dalvand, Mohammad Jafar; Mohtasebi, Seyed Saeid; Rafiee, Shahin

    2014-11-01

    The purpose of this article was to present a new drying method for agricultural products. Electrohydrodynamic (EHD) has been applied for drying of agricultural materials due to several advantages such as energy saving, low cost equipment, low drying temperatures, and superior material quality. To evaluate this method, an EHD dryer based on solar (photovoltaic) energy was designed and fabricated. Moreover, the optimum condition for the EHD drying of kiwi fruit was studied by applying the Box-Behnken design of response surface methodology. The desirability function was applied for optimization in case of single objective and multiobjective functions. By using the multiobjective optimization method, maximum desirability value of 0.865 was obtained based on the following: applied voltage of 15 kV, field strength of 5.2 kV cm(-1), without forced air stream, and finally a combination of 17 discharge electrodes (needles). The results indicated that increasing the applied voltage from 6 to 15 kV, moisture ratio (MR) decreased, though energy efficiency and energy consumption were increasing. On the other hand, field strength of 5.2 kV cm(-1) was the optimal point in terms of MR.

  9. Analysis of extreme summers and prior late winter/spring conditions in central Europe

    Directory of Open Access Journals (Sweden)

    C. Träger-Chatterjee

    2013-05-01

    Full Text Available Drought and heat waves during summer in mid-latitudes are a serious threat to human health and agriculture and have negative impacts on the infrastructure, such as problems in energy supply. The appearance of such extreme events is expected to increase with the progress of global warming. A better understanding of the development of extremely hot and dry summers and the identification of possible precursors could help improve existing seasonal forecasts in this regard, and could possibly lead to the development of early warning methods. The development of extremely hot and dry summer seasons in central Europe is attributed to a combined effect of the dominance of anticyclonic weather regimes and soil moisture–atmosphere interactions. The atmospheric circulation largely determines the amount of solar irradiation and the amount of precipitation in an area. These two variables are themselves major factors controlling the soil moisture. Thus, solar irradiation and precipitation are used as proxies to analyse extreme sunny and dry late winter/spring and summer seasons for the period 1958–2011 in Germany and adjacent areas. For this purpose, solar irradiation data from the European Center for Medium Range Weather Forecast 40-yr and interim re-analysis dataset, as well as remote sensing data are used. Precipitation data are taken from the Global Precipitation Climatology Project. To analyse the atmospheric circulation geopotential data at 850 hPa are also taken from the European Center for Medium Range Weather Forecast 40-yr and interim re-analysis datasets. For the years in which extreme summers in terms of high solar irradiation and low precipitation are identified, the previous late winter/spring conditions of solar irradiation and precipitation in Germany and adjacent areas are analysed. Results show that if the El Niño–Southern Oscillation (ENSO is not very intensely developed, extremely high solar irradiation amounts, together with

  10. Analysis of extreme summers and prior late winter/spring conditions in central Europe

    Science.gov (United States)

    Träger-Chatterjee, C.; Müller, R. W.; Bendix, J.

    2013-05-01

    Drought and heat waves during summer in mid-latitudes are a serious threat to human health and agriculture and have negative impacts on the infrastructure, such as problems in energy supply. The appearance of such extreme events is expected to increase with the progress of global warming. A better understanding of the development of extremely hot and dry summers and the identification of possible precursors could help improve existing seasonal forecasts in this regard, and could possibly lead to the development of early warning methods. The development of extremely hot and dry summer seasons in central Europe is attributed to a combined effect of the dominance of anticyclonic weather regimes and soil moisture-atmosphere interactions. The atmospheric circulation largely determines the amount of solar irradiation and the amount of precipitation in an area. These two variables are themselves major factors controlling the soil moisture. Thus, solar irradiation and precipitation are used as proxies to analyse extreme sunny and dry late winter/spring and summer seasons for the period 1958-2011 in Germany and adjacent areas. For this purpose, solar irradiation data from the European Center for Medium Range Weather Forecast 40-yr and interim re-analysis dataset, as well as remote sensing data are used. Precipitation data are taken from the Global Precipitation Climatology Project. To analyse the atmospheric circulation geopotential data at 850 hPa are also taken from the European Center for Medium Range Weather Forecast 40-yr and interim re-analysis datasets. For the years in which extreme summers in terms of high solar irradiation and low precipitation are identified, the previous late winter/spring conditions of solar irradiation and precipitation in Germany and adjacent areas are analysed. Results show that if the El Niño-Southern Oscillation (ENSO) is not very intensely developed, extremely high solar irradiation amounts, together with extremely low precipitation

  11. Estimating statistics of European wet and dry spells and associated precipitation extremes - interannual variability and trends

    Science.gov (United States)

    Zolina, O.; Simmer, C.; Belyaev, K.; Gulev, S.; Koltermann, K. P.

    2013-12-01

    Probability distributions of the durations of wet and dry spells were modeled by applying truncated geometric distribution. It has been also extended to the fractional truncated geometric distribution which allows for the discrimination between the roles of a changing number of wet days and of a regrouping of wet and dry days in forming synoptic structure of precipitation. Analyses were performed using 2 collections of daily rain gauge data namely ECA (about 1000 stations) and regional German DWD network (more than 6000 stations) for the period from 1950 to 2009. Wet spells exhibit a statistically significant lengthening over northern Europe and central European Russia, which is especially pronounced in winter when the mean duration of wet periods increased by 15%-20%. In summer wet spells become shorter over Scandinavia and northern Russia. The duration of dry spells decreases over Scandinavia and southern Europe in both winter and summer. Climate tendencies in extreme wet and dry spell durations may not necessarily follow those in mean characteristics. The changing numbers of wet days cannot explain the long-term variability in the duration of wet and dry periods. The observed changes are mainly due to the regrouping of wet and dry days. The tendencies in duration of wet and dry spells have been analyzed for a number of European areas. Over the Netherlands both wet and dry periods are extended in length during the cold and the warm season. A simultaneous shortening of wet and dry periods is found in southern Scandinavia in summer. Over France and central southern Europe during both winter and summer and over the Scandinavian Atlantic coast in summer, opposite tendencies in the duration of wet and dry spells were identified. Growing durations of wet spells are associated with more intense precipitation events while precipitation during shorter wet spells become weaker. Both analyses of relatively coarse resolution ECA data and high resolution DWD station network

  12. Conditional probability of rainfall extremes across multiple durations

    Science.gov (United States)

    Le, Phuong Dong; Leonard, Michael; Westra, Seth

    2017-04-01

    The conditional probability that extreme rainfall will occur at one location given that it is occurring at another location is critical in engineering design and management circumstances including planning of evacuation routes and the sitting of emergency infrastructure. A challenge with this conditional simulation is that in many situations the interest is not so much the conditional distributions of rainfall of the same duration at two locations, but rather the conditional distribution of flooding in two neighbouring catchments, which may be influenced by rainfall of different critical durations. To deal with this challenge, a model that can consider both spatial and duration dependence of extremes is required. The aim of this research is to develop a model that can take account both spatial dependence and duration dependence into the dependence structure of extreme rainfalls. To achieve this aim, this study is a first attempt at combining extreme rainfall for multiple durations within a spatial extreme model framework based on max-stable process theory. Max-stable processes provide a general framework for modelling multivariate extremes with spatial dependence for just a single duration extreme rainfall. To achieve dependence across multiple timescales, this study proposes a new approach that includes addition elements representing duration dependence of extremes to the covariance matrix of max-stable model. To improve the efficiency of calculation, a re-parameterization proposed by Koutsoyiannis et al. (1998) is used to reduce the number of parameters necessary to be estimated. This re-parameterization enables the GEV parameters to be represented as a function of timescale. A stepwise framework has been adopted to achieve the overall aims of this research. Firstly, the re-parameterization is used to define a new set of common parameters for marginal distribution across multiple durations. Secondly, spatial interpolation of the new parameter set is used to

  13. Atomistic Simulations of Material Properties under Extreme Conditions

    Science.gov (United States)

    An, Qi

    Extreme conditions involve low or high temperatures (> 1500 K), high pressures (> 30 MPa), high strains or strain rates, high radiation fluxes (> 100 dpa), and high electromagnetic fields (> 15T). Material properties under extreme conditions can be extremely different from those under normal conditions. Understanding material properties and performance under extreme conditions, including their dynamic evolution over time, plays an essential role in improving material properties and developing novel materials with desired properties. To understand material properties under extreme conditions, we use molecular dynamics (MD) simulations with recently developed reactive force fields (ReaxFF) and traditional embedded atom methods (EAM) potentials to examine various materials (e.g., energetic materials and binary liquids) and processes. The key results from the simulations are summarized below. Anisotropic sensitivity of RDX crystals: Based on the compress-and-shear reactive dynamics (CS-RD) simulations of cyclotrimethylene trinitramine (RDX) crystals, we predict that for mechanical shocks between 3 and 7 GPa, RDX is the most sensitive to shocks perpendicular to the (100) and (210) planes, while it is insensitive to those perpendicular to the (120), (111), and (110) planes. The simulations demonstrate that the molecular origin of anisotropic shock sensitivity is the steric hindrance to shearing of adjacent slip planes. Mechanisms of hotspot formation in polymer bonded explosives (PBXs): The simulations of a realistic model of PBXs reveal that hotspots may form at the nonplanar interfaces where shear relaxation leads to a dramatic temperature increase that persists long after the shock front has passed the interface. For energetic materials this temperature increase is coupled to chemical reactions that eventually lead to detonation. We show that decreasing the density of the binder eliminates the hotspots or reduces the sensitivity. Cavitation in binary metallic liquids

  14. Determination of drying characteristics and quality properties of eggplant in different drying conditions

    Directory of Open Access Journals (Sweden)

    Gözde Bayraktaroglu Urun

    2015-12-01

    Full Text Available Drying is the most traditional process used for preserving eggplant a long time. The aim of this study was to determining drying characteristics and quality properties of eggplant dried by sun drying, hot air convective drying and infrared assisted convective drying. Convective drying and infrared assisted convective were carried out in a convective dryer at three different temperatures(40°, 50°, 60°C and air velocity at 5 m/s.The increasing of temperatures during the drying of eggplant led to a significant reduction of the drying time. However loss of nutrition was observed in eggplant samples dried at higher temperature.The biggest change in colour parameters was observed in samples dried with sun drying.So it was thought that sun drying had a negative effect on quality properties of eggplant samples.

  15. Prebiotic cell membranes that survive extreme environmental pressure conditions.

    Science.gov (United States)

    Kapoor, Shobhna; Berghaus, Melanie; Suladze, Saba; Prumbaum, Daniel; Grobelny, Sebastian; Degen, Patrick; Raunser, Stefan; Winter, Roland

    2014-08-04

    Attractive candidates for compartmentalizing prebiotic cells are membranes comprised of single-chain fatty acids. It is generally believed that life may have originated in the depth of the protoocean, that is, under high hydrostatic pressure conditions, but the structure and physical-chemical properties of prebiotic membranes under such conditions have not yet been explored. We report the temperature- and pressure-dependent properties of membranes composed of prebiotically highly-plausible lipids and demonstrate that prebiotic membranes could not only withstand extreme temperatures, but also serve as robust models of protocells operating in extreme pressure environments. We show that pressure not only increases the stability of vesicular systems but also limits their flexibility and permeability to solutes, while still keeping the membrane in an overall fluid-like and thus functional state. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  16. Ultrasonic Technique for Density Measurement of Liquids in Extreme Conditions

    Directory of Open Access Journals (Sweden)

    Rymantas Kazys

    2015-08-01

    Full Text Available An ultrasonic technique, invariant to temperature changes, for a density measurement of different liquids under in situ extreme conditions is presented. The influence of geometry and material parameters of the measurement system (transducer, waveguide, matching layer on measurement accuracy and reliability is analyzed theoretically along with experimental results. The proposed method is based on measurement of the amplitude of the ultrasonic wave, reflected from the interface of the solid/liquid medium under investigation. In order to enhance sensitivity, the use of a quarter wavelength acoustic matching layer is proposed. Therefore, the sensitivity of the measurement system increases significantly. Density measurements quite often must be performed in extreme conditions at high temperature (up to 220 °C and high pressure. In this case, metal waveguides between piezoelectric transducer and the measured liquid are used in order to protect the conventional transducer from the influence of high temperature and to avoid depolarization. The presented ultrasonic density measurement technique is suitable for density measurement in different materials, including liquids and polymer melts in extreme conditions. A new calibration algorithm was proposed. The metrological evaluation of the measurement method was performed. The expanded measurement uncertainty Uρ = 7.4 × 10−3 g/cm3 (1%.

  17. The dissociation constant of water at extreme conditions

    Science.gov (United States)

    Gonzalez-Vazquez, Otto; Giacomazzi, Luigi; Pinilla, C.; Scandolo, Sandro

    2013-06-01

    Only one out of 107 water molecules is dissociated in liquid water at ambient conditions, but the concentration of dissociated molecules increases with pressure ad temperature, and water eventually reaches a fully dissociated state when pressure exceeds 50-100 GPa and temperature reaches a few thousand Kelvin. The behavior of the dissociation constant of water (pKa) at conditions intermediate between ambient and the fully dissociated state is poorly known. Yet, the water pKa is a parameter of primary importance in the aqueous geochemistry as it controls the solubility of ions in geological fluids. We present results of molecular dynamics calculations of the pKa water at extreme conditions. Free-energy differences between the undissociated and the dissociated state are calculated by thermodynamic integration along the dissociation path. The calculations are based on a recently developed all-atom polarizable force-field for water, parametrized on density-functional theory calculations.

  18. The Matter in Extreme Conditions (MEC) instrument at LCLS

    Science.gov (United States)

    Nagler, Bob

    2015-06-01

    The last five years have seen the commissioning of and first user experiments on both the Free Electron Laser in Hamburg (FLASH) and the Linac Coherent Light Source (LCLS) in Stanford, and more are slated to come online in the next couple of years . The high photon frequency (i.e. larger than the plasma frequency of solid density), short pulse length (i.e. 10s to 100s of femtoseconds) and large photon number per pulse (i.e. 1012 photons per pulse) make it an ideal source to create and study states of matter at high energy density, a long-standing scientific challenge. Indeed, while matter in extreme conditions, which for the purpose of this talk we define as states under pressure up to hundreds of GPa and with temperatures ranging between 1eV and 1000eV, has been studied through dynamic shock compression and there has been significant progress made over many decades. However, large uncertainties still exist in the atomic structure and crystallographic structure, existence of high pressure phases, scattering factors, and equation of state of matter in extreme conditions. The Matter in Extreme Condition (MEC) instrument at LCLS is designed to overcome the unique experimental challenges that the study of matter in extreme conditions bring. It combines a suite of diagnostics and high power and energy optical lasers, which are standard fare in this research field, with the unmatched LCLS X-ray beam, to create an instrument that will be at the forefront of, and have a major impact on MEC science, in particular in the field of high pressure, warm dense matter, high energy density, and ultra-high intensity laser-matter interaction studies. The LCLS beam allows for unique investigation in all these extreme states using diagnostic methods such as X-ray Thomson Scattering, X-ray emission spectroscopy, X-ray diffraction, X-ray absorption spectroscopy, X-ray phase-contrast imaging, and pumping specific absorption lines to study (dense) plasma kinetics. Augmented with optical

  19. Detecting Climate Signals in Precipitation Extremes from TRMM (1998-2013) - Increasing Contrast Between Wet and Dry Extremes During the "Global Warming Hiatus"

    Science.gov (United States)

    Wu, Huey-Tzu Jenny; Lau, William K.-M.

    2016-01-01

    We investigate changes in daily precipitation extremes using Tropical Rainfall Measuring Mission (TRMM) data (1998-2013), which coincides with the "global warming hiatus." Results show a change in probability distribution functions of local precipitation events (LPEs) during this period consistent with previous global warming studies, indicating increasing contrast between wet and dry extremes, with more intense LPE, less moderate LPE, and more dry (no rain) days globally. Analyses for land and ocean separately reveal more complex and nuanced changes over land, characterized by a strong positive trend (+12.0% per decade, 99% confidence level (c.l.)) in frequency of extreme LPEs over the Northern Hemisphere extratropics during the wet season but a negative global trend (-6.6% per decade, 95% c.l.) during the dry season. A significant global drying trend (3.2% per decade, 99% c.l.) over land is also found during the dry season. Regions of pronounced increased dry events include western and central U.S., northeastern Asia, and Southern Europe/Mediterranean.

  20. Detecting climate signals in precipitation extremes from TRMM (1998-2013)—Increasing contrast between wet and dry extremes during the "global warming hiatus"

    Science.gov (United States)

    Wu, Huey-Tzu Jenny; Lau, William K.-M.

    2016-02-01

    We investigate changes in daily precipitation extremes using Tropical Rainfall Measuring Mission (TRMM) data (1998-2013), which coincides with the "global warming hiatus." Results show a change in probability distribution functions of local precipitation events (LPEs) during this period consistent with previous global warming studies, indicating increasing contrast between wet and dry extremes, with more intense LPE, less moderate LPE, and more dry (no rain) days globally. Analyses for land and ocean separately reveal more complex and nuanced changes over land, characterized by a strong positive trend (+12.0% per decade, 99% confidence level (c.l.)) in frequency of extreme LPEs over the Northern Hemisphere extratropics during the wet season but a negative global trend (-6.6% per decade, 95% c.l.) during the dry season. A significant global drying trend (3.2% per decade, 99% c.l.) over land is also found during the dry season. Regions of pronounced increased dry events include western and central U.S., northeastern Asia, and Southern Europe/Mediterranean.

  1. Large Chip Production Mechanism under the Extreme Load Cutting Conditions

    Institute of Scientific and Technical Information of China (English)

    LIU Xianli; HE Genghuang; YAN Fugang; CHENG Yaonan; LIU Li

    2015-01-01

    There has existed a great deal of theory researches in term of chip production and chip breaking characteristics under conventional cutting and high speed cutting conditions, however, there isn’t sufficient research on chip formation mechanism as well as its influence on cutting state regarding large workpieces under extreme load cutting. This paper presents a model of large saw-tooth chip through applying finite element simulation method, which gives a profound analysis about the characteristics of the extreme load cutting as well as morphology and removal of the large chip. In the meantime, a calculation formula that gives a quantitative description of the saw-tooth level regarding the large chip is established on the basis of cutting experiments on high temperature and high strength steel 2.25Cr-1Mo-0.25V. The cutting experiments are carried out by using the scanning electron microscope and super depth of field electron microscope to measure and calculate the large chip produced under different cutting parameters, which can verify the validity of the established model. The calculating results show that the large saw-toothed chip is produced under the squeezing action between workpiece and cutting tools. In the meanwhile, the chip develops a hardened layer where contacts the cutting tool and the saw-tooth of the chip tend to form in transverse direction. This research creates the theoretical model for large chip and performs the cutting experiments under the extreme load cutting condition, as well as analyzes the production mechanism of the large chip in the macro and micro conditions. Therefore, the proposed research could provide theoretical guidance and technical support in improving productivity and cutting technology research.

  2. [Sports and extreme conditions. Cardiovascular incidence in long term exertion and extreme temperatures (heat, cold)].

    Science.gov (United States)

    Melin, B; Savourey, G

    2001-06-30

    During ultra-endurance exercise, both increase in body temperature and dehydration due to sweat losses, lead to a decrease in central blood volume. The heart rate drift allows maintaining appropriate cardiac output, in order to satisfy both muscle perfusion and heat transfer requirements by increasing skin blood flow. The resulting dehydration can impair thermal regulation and increase the risks of serious accidents as heat stroke. Endurance events, lasting more than 8 hours, result in large sweat sodium chloride losses. Thus, ingestion of large amounts of water with poor salt intake can induce symptomatic hyponatremia (plasma sodium extreme condition.

  3. Extreme fog events in Poland with respect to circulation conditions

    Science.gov (United States)

    Ustrnul, Z.; Czekierda, D.; Wypych, A.

    2010-09-01

    Fog is a phenomenon which belongs to a group of so-called hydrometeorites and, according to the different dictionaries, it is a suspension of water droplets or ice crystals in the ground layer of the air that impairs visibility in the horizontal direction below 1 km. The phenomenon of fog, although much less dynamic or violent than other extreme phenomena, such as thunderstorms or hail, is equally dangerous and brings about huge social and economic complications. Land and air transportation suffer and fog may sometimes leads to a complete crippling of the whole economy in an area where fog occurs. The main objective of the study is determination of the circulation types bringing extreme fog events in Poland. The duration of fog at each meteorological station was considered as the main input data originated from 54 synoptic stations located across the country. The mentioned data series cover the period of 56 years (1951-2006). The occurrence of fog depends on meteorological conditions caused to a large extent by a given synoptic situation and local terrain conditions. In this study, according to its objectives, only circulation conditions are taken into consideration. These have been described by 5 different circulation classifications (Grosswetterlagen, Litynski, Osuchowska-Klein, Niedzwiedz and Ustrnul). Situations when this phenomenon occurred across a large part of the country were taken into detailed consideration. Special attention was paid to fog coverage during 24-hour periods. In this work, in light of certain doubts about the homogeneity of the observation material available, the intensity of fog was not included, as it requires additional and very tedious analysis. In the first step all cases of fog during the 1966-2006 study period which lasted 24 hours at more than 10 of the considered weather stations, i.e: at least 5 stations have been considered. As expected, in most cases, either a centre of a classical high pressure system or a high pressure wedge

  4. X-ray diffraction at Matter in Extreme Conditions endstation

    Science.gov (United States)

    Xing, Zhou; Galtier, Eric; Lee, Hae Ja; Nagler, Bob

    2015-11-01

    Understanding dynamic response at the atomic level under extreme conditions is highly sought after goal to science frontiers studying warm dense matter, high pressure, geoscience, astrophysics, and planetary science. Thus it is of importance to determine the high pressure phases or metastable phases of material under shock compression. In situ X-ray diffraction technique using LCLS free electron laser X-ray is a powerful tool to record structural behavior and microstructure evolution in dense matter. Shock-induced compression and phase transitions of material lead to changes of the lattice spacing or evolution of new X-ray diffraction patterns. In this talk, we describe a platform dedicated for the X-ray diffraction studies at Matter in Extreme Conditions (MEC), which can be used to reconstruct a complete diffraction pattern from numerous detectors, optimize detector positioning in a timely manner, extract the lattice spacing profiles and texture features. This platform is available to the user community for real-time analysis. We will also discuss experimental results, using this platform, on the crystalline silicon phase transitions up to 60 GPa.

  5. Triticale in the years with extreme weather conditions

    Directory of Open Access Journals (Sweden)

    Nožinić Miloš

    2009-01-01

    Full Text Available Unlike other grain crops, the area under triticale in the Republic of Srpska has been expanding every year. Since the introduction of this plant species in the broad production began a few years ago, the finding of the optimal variety agrotechnique in different environmental conditions has great importance. This paper deals with the results of the trials from seven locations in two very extreme vegetation seasons (2002/03, 2006/07. High yield of triticale on the location Banja Luka (150 m alt. with five triticale varieties in four sowing rates in the replication trial in very unfavorable weather conditions in 2003, points to emphasized triticale tolerance to high temperatures and drought. High grain yield of triticale in the trials on the locations Banja Luka, Butmir (460 m alt. and Živince (230 m alt. was obtained in 2007 too, when all vegetation months had higher mean temperature than long term average, what is a unique appearance in the entire 'meteorological history'. In the paper the appearance of the earliest triticale heading is described and explained. It happened at one production trial on Manjača (250 m alt. in the first decade of March in 2007. On the another location on Manjača (450 m alt., in the macrotrial, rye showed much higher tolerance to extreme soil acidity, than triticale. Obtained results and unusual appearances on triticale are helpful for the further research of the stability and adaptability of more important triticale traits. .

  6. Green roof establishment in extreme conditions : two case studies

    Energy Technology Data Exchange (ETDEWEB)

    Grothe, R. [Aloha Landscaping, Inc., Mendota Heights, MN (United States); Trichie, J. [Shakopee Mdewakanton Sioux Community, MN (United States)

    2007-07-01

    Green roof construction in the United States is growing at a rate of 60 to 80 per cent per year. This paper presented two case studies of green roof construction in Minnesota. In both cases, construction and budgeting delays moved the installation of the green roofs from early-May to mid-July. The first case study was a 20,000 square foot extensive green roof on the new Minneapolis Central Library which was completed in 2005. The second case study was a 30,000 square foot extensive green roof on the Mdewakanton Sioux Waste Water Treatment Plant in Shakopee, which was completed in 2006. This paper demonstrated that in order for green roofs to serve the functions for which they were intended, clear guidelines and specifications are needed to ensure that they are healthy. The size and locations of the two roofs were quite different, but they were identical in terms of waterproofing. State-of-the-art inverted hot-applied roof membrane technology was used in both roofs along with sub-surface irrigation systems. A mycorrhizae fungi was used in both cases to amend the growing medium. Both roofs used a diverse pallet of native and traditional sedum plant material. This paper highlighted preventative measures taken to ensure the successful installation and establishment of the two roofs built during extreme heat and drought-like conditions. The positive results confirm that it is possible to install green roofs during extremely harsh summer conditions. 9 refs., 4 tabs., 3 figs.

  7. Variance swap payoffs, risk premia and extreme market conditions

    DEFF Research Database (Denmark)

    Rombouts, Jeroen V.K.; Stentoft, Lars; Violante, Francesco

    This paper estimates the Variance Risk Premium (VRP) directly from synthetic variance swap payoffs. Since variance swap payoffs are highly volatile, we extract the VRP by using signal extraction techniques based on a state-space representation of our model in combination with a simple economic...... constraint. Our approach, only requiring option implied volatilities and daily returns for the underlying, provides measurement error free estimates of the part of the VRP related to normal market conditions, and allows constructing variables indicating agents' expectations under extreme market conditions....... The latter variables and the VRP generate different return predictability on the major US indices. A factor model is proposed to extract a market VRP which turns out to be priced when considering Fama and French portfolios....

  8. Material dynamics under extreme conditions of pressure and strain rate

    Energy Technology Data Exchange (ETDEWEB)

    Remington, B A; Allen, P; Bringa, E; Hawreliak, J; Ho, D; Lorenz, K T; Lorenzana, H; Meyers, M A; Pollaine, S W; Rosolankova, K; Sadik, B; Schneider, M S; Swift, D; Wark, J; Yaakobi, B

    2005-09-06

    Solid state experiments at extreme pressures (10-100 GPa) and strain rates ({approx}10{sup 6}-10{sup 8}s{sup -1}) are being developed on high-energy laser facilities, and offer the possibility for exploring new regimes of materials science. These extreme solid-state conditions can be accessed with either shock loading or with a quasi-isentropic ramped pressure drive. Velocity interferometer measurements establish the high pressure conditions. Constitutive models for solid-state strength under these conditions are tested by comparing 2D continuum simulations with experiments measuring perturbation growth due to the Rayleigh-Taylor instability in solid-state samples. Lattice compression, phase, and temperature are deduced from extended x-ray absorption fine structure (EXAFS) measurements, from which the shock-induced {alpha}-{omega} phase transition in Ti and the {alpha}-{var_epsilon} phase transition in Fe are inferred to occur on sub-nanosec time scales. Time resolved lattice response and phase can also be measured with dynamic x-ray diffraction measurements, where the elastic-plastic (1D-3D) lattice relaxation in shocked Cu is shown to occur promptly (< 1 ns). Subsequent large-scale molecular dynamics (MD) simulations elucidate the microscopic dynamics that underlie the 3D lattice relaxation. Deformation mechanisms are identified by examining the residual microstructure in recovered samples. The slip-twinning threshold in single-crystal Cu shocked along the [001] direction is shown to occur at shock strengths of {approx}20 GPa, whereas the corresponding transition for Cu shocked along the [134] direction occurs at higher shock strengths. This slip-twinning threshold also depends on the stacking fault energy (SFE), being lower for low SFE materials. Designs have been developed for achieving much higher pressures, P > 1000 GPa, in the solid state on the National Ignition Facility (NIF) laser.

  9. Effects of Drying Condition and Binding Agent on the Quality Characteristics of Ground Dried-Pork Meat Products.

    Science.gov (United States)

    Choi, Yun-Sang; Ku, Su-Kyung; Park, Jong-Dae; Kim, Hee-Ju; Jang, Aera; Kim, Young-Boong

    2015-01-01

    The purpose of this study was to investigate the influence of processing conditions (temperature and time) and binding agent types (glutinous rice flour, potato starch, bean flour, and acorn flour) on the physicochemical and sensory characteristics of ground dried-pork meat product. For this purpose, ground dried-pork meat product was produced by adding several binding agents at different drying temperatures and times. The drying time affected moisture content and water activity in all drying temperature. However, under the similar drying conditions, the extent of drying varied depending on the type of binding agents. The results of sensory evaluation for texture degree and overall acceptability indicated the following: overall, higher drying temperatures and longer drying time heightened the degree of texture, and the overall acceptability varied depending on binding agent type. Physicochemical and sensory characteristics were analyzed to determine any possible correlation. The results revealed a high correlation between moisture content, water activity, shear forces, and sensory evaluation (p<0.01). However, there was no correlation with respect to overall acceptability.

  10. Experimental study on rehydration conditions of freeze-dried platelets

    Institute of Scientific and Technical Information of China (English)

    Ju-li FAN; Xian-guo XU; Shao-zhi ZHANG; Fa-ming ZHU; Guang-ming CHEN; Li-xing YAN

    2009-01-01

    A rehydration process for freeze-dried human platelets was studied on 1 ml of samples.The effects of prehydration duration,prehydration temperature,an rehydration solution on the recovery rate,mean platelet volume(MPV),and platelet distribution width(PDW)were investigated.The mass changes during the prehydration process were also studied.Three prehydration durations:0,1.5,and 3.5 h,and two rehydration solutions:platelet-poor plasma and phosphate-buffered saline(PBS),were tested.It was found that:(1)the prehydration was of significance;(2)1.5 h of prehydration had better effects than 3.5 h of prehydration;(3)as a rehydration solution,the platelet-poor plasma behaved better than the PBS.The impacts of prehydration duration and temperature on the results were studied.There was almost no difference between 35 and 37℃.Among all the prehydration durations tested,15,30,60,90,and 120 min,the best result was achieved with the time duration of 15 min.The weights of prehydrated platelets at the end of each test were measured and the water contents were calculated.Atier 15 min of prehydration,the water contents in the samples were about(4.8±0.01)%and(5.27±0.29)%(w/w)corresponding to the conditions of 35 and 37 ℃.respectively.These results will be helpful for further studies on the freeze-drying of mammalian cells.

  11. Comparison of Surfactant Distributions in Pressure-Sensitive Adhesive Films Dried from Dispersion under Lab-Scale and Industrial Drying Conditions.

    Science.gov (United States)

    Baesch, S; Siebel, D; Schmidt-Hansberg, B; Eichholz, C; Gerst, M; Scharfer, P; Schabel, W

    2016-03-01

    Film-forming latex dispersions are an important class of material systems for a variety of applications, for example, pressure-sensitive adhesives, which are used for the manufacturing of adhesive tapes and labels. The mechanisms occurring during drying have been under intense investigations in a number of literature works. Of special interest is the distribution of surfactants during the film formation. However, most of the studies are performed at experimental conditions very different from those usually encountered in industrial processes. This leaves the impact of the drying conditions and the resulting influence on the film properties unclear. In this work, two different 2-ethylhexyl-acrylate (EHA)-based adhesives with varying characteristics regarding glass transition temperature, surfactants, and particle size distribution were investigated on two different substrates. The drying conditions, defined by film temperature and mass transfer in the gas phase, were varied to emulate typical conditions encountered in the laboratory and industrial processes. Extreme conditions equivalent to air temperatures up to 250 °C in a belt dryer and drying rates of 12 g/(m(2)·s) were realized. The surfactant distributions were measured by means of 3D confocal Raman spectroscopy in the dry film. The surfactant distributions were found to differ significantly with drying conditions at moderate film temperatures. At elevated film temperatures the surfactant distributions are independent of the investigated gas side transport coefficients: the heat and mass transfer coefficient. Coating on substrates with significantly different surface energies has a large impact on surfactant concentration gradients, as the equilibrium between surface and bulk concentration changes. Dispersions with higher colloidal stability showed more homogeneous lateral surfactant distributions. These results indicate that the choice of the drying conditions, colloidal stability, and substrates is crucial

  12. Large Scale Moisture Fluxes that are related to dry and wet conditions over Mediterranean Basin

    Science.gov (United States)

    Sahin, Sinan; Luterbacher, Juerg; Xoplaki, Elena; Turkes, Murat

    2016-04-01

    Large scale moisture flux analysis was carried out for the Mediterranean Basin in order to investigate the large scale atmospheric controls on moisture flux convergence that are related to dry and wet conditions. The seasonal moisture budget (precipitation minus evaporation) was calculated using the National Centers for Environmental Prediction - National Center for Atmospheric Research reanalysis data for the period 1949-2014. We focus on winter and summer circulation patterns for explaining the changes in dry and wet conditions rather than spring and autumn, as the transitional nature and characterization of these seasons are more uncertain in the Mediterranean basin. The driest and wettest years were chosen according to Standardized Precipitation Index (SPI) and the differences between those years and average conditions were compared statistically and graphically. According to results, large scale climate changes over Mediterranean Region are linked to significant changes of the moisture fluxes in the Gulf of Mexico region and partially in the US East coast especially for wet years. Therefore the climatic role of the Gulf Stream for extreme climate conditions over Mediterranean region should be investigated.

  13. Existing Condition Analysis of Dry Spent Fuel Storage Technology

    Institute of Scientific and Technical Information of China (English)

    LI Ning; XU Lan; HAO Jian-sheng

    2016-01-01

    As in some domestic nuclear power plants, spent fuel pools near capacity, away-from-reactor type storage should be arranged to transfer spent fuel before the pool capacity is full and the plants can operate in safety. This study compares the features of wet and dry storage technology, analyzes the actualities of foreign dry storage facilities and then introduces structural characteristics of some foreign dry storage cask. Finally, a glance will be cast on the failure of away-from-reactor storage facilities of Pressurized Water Reactor(PWR)to meet the need of spent-fuel storage. Therefore, this study believes dry storage will be a feasible solution to the problem.

  14. The effects of drying conditions on moisture transfer and quality of pomegranate fruit leather (pestil

    Directory of Open Access Journals (Sweden)

    Fatih Mehmet Yılmaz

    2017-01-01

    Full Text Available Vacuum, cabinet and open air drying of pomegranate fruit leather were carried out at various drying conditions to monitor the drying kinetics together with bionutrient degradation of the product. Drying curves exhibited first order drying kinetics and effective moisture diffusivity values varied between 3.1 × 10−9 and 52.6 × 10−9 m2/s. The temperature dependence of the effective moisture diffusivity was satisfactorily described by an Arrhenius-type relationship. Drying conditions, product thickness and operation temperature had various effects on drying rate and final quality of the product. In terms of drying kinetics and final quality of product, vacuum drying had higher drying rate with higher conservation of phenolic, anthocyanin and ascorbic acid that is connected to faster drying condition and oxygen deficient medium. Anthocyanin content was significantly affected by drying method, drying temperature and product thickness. Scatter plot using principle component analysis enabled better understanding of moisture transfer rate and anthocyanin change under various drying conditions.

  15. The frequency of occurrence of extreme and detrimental meteorological conditions for vegetation of crops in Poland (1971–2010

    Directory of Open Access Journals (Sweden)

    Ziernicka-Wojtaszek Agnieszka

    2016-06-01

    Full Text Available The frequency of occurrence of extreme and detrimental meteorological conditions for vegetation of crops in Poland (1971-2010. The subject, and aim of this study is the comparison of the frequency of occurrence of thermal, precipitation and pluvio-thermal conditions detrimental to agriculture in Poland during two periods: 1971-2000 and 1981-2010, constituting the former, and the current climate normal, respectively. Each month of the vegetation period (April-October was, in accordance with the current accounts carried out by agriculture correspondents, assigned to one of the following categories: favorable for vegetation, dry, dry and cool, cool, cool and humid, humid, dry and hot. An identical classification of meteorological vegetation conditions was also carried out for months characterized by extreme air temperature and precipitation values. Extreme values were defined as those monthly temperature mean values, and monthly precipitation totals, the probability of exceeding of which is lower than 10%, i.e. their probability of occurrence, or the socalled recurrence interval, is once every 10 years. The differences existing between the analyzed 30-year periods, can be attributed to the present day climate change - a significant increase in air temperature in April, June, July, and August, with a lack of significant precipitation trends. In the two compared periods, an increase in the number of extreme months from 74 to 82 was stated. The biggest changes during the extreme months were observed for precipitation deficits combined with hot air temperatures, namely, an increase from 15 to 29 months. In general, all the analyzed months of the vegetation period showed an increase in dry months (90 to 105 cases and a decrease in cool months (44 to 24 cases.

  16. Combined influence of growth and drying conditions on the activity of dried Lactobacillus plantarum

    NARCIS (Netherlands)

    Linders, L.J.M.; Kets, E.P.W.; Bont, J.A.M. de; Riet, K.V. van 't

    1998-01-01

    The production of active dried starter cultures can be influenced at several levels in the production process. In this paper the following process factors are discussed: osmotic stress during growth and cell density prior to drying. Contradicting results are reported in the literature on the influen

  17. Dry, drier, driest: An Australian story of extreme years and potential ecosystem collapse

    Science.gov (United States)

    Wardle, G. M.; Dickman, C. R.; Greenville, A. C.

    2016-12-01

    Ecosystems are expected to undergo large changes due to an increase in the frequency and intensity of extreme events. We can expect droughts to be longer, flooding to be more intense, and heatwaves and fires to increase. Importantly, at the regional scale these projections which are based on global climate models come with additional uncertainties that challenge how we can plan and evaluate options for adaptation. For many ecosystems, the understanding of the interdependencies and function is still limited, and particularly so for areas such as inland Australia that already exhibit unpredictable rainfall and lack strong seasonality. These drylands are water-limited and operate differently in dry, or wet years, when episodic pulses of resources drive increases in productivity. Increased extremes have the potential to disrupt the function of these highly dynamic and complex systems through feedbacks, synergies and through memory or delayed responses to change. Using our long-term work in the Simpson Desert as a case study, we explore the trends in productivity, the responses of flora and fauna to these opportunities and the spatial connectedness and heterogeneities that support the persistence of the ecosystem through dry times. Theory tells us that ecosystems may shift states abruptly when they cross critical thresholds. For example, arid grasslands may no longer have the capacity to return to a productive state following good rains. This happens under desertification, where plant cover and growth is limited — with flow on consequences for the entire ecosystem. Forecasting such changes is crucial but the fundamental knowledge relies on information that spans both long time scales and large spatial scales. We examine the knowledge gaps in quantifying ecosystem collapse using our IUCN ecosystem risk assessment of the Georgina gidgee woodlands. We conclude by arguing that without long-term data on trends and integration across the biophysical and and biological

  18. Extreme conditions over Europe and North America: role of the Atlantic Multidecadal Variability

    Science.gov (United States)

    Ruprich-Robert, Yohan; Msadek, Rym; Delworth, Tom

    2016-04-01

    The Atlantic Multidecadal Variability (AMV) is the result and possibly the source of marked modulations of the climate over many areas of the globe. For instance, the relatively warm and dry climate of North America throughout the 30-yr interval of 1931-60, during which the Dust Bowl and the 1950's drought occurred, has been linked to the concomitant warm phase of the AMV. During this period relative warm and wet conditions prevailed over Europe. After 1960, the Atlantic began to cool, and for almost three decades the North American climate turned wetter and cooler whereas Europe experienced cooler and dryer conditions. However, the shortness of the historical observations compared to the AMV period suggested by longer proxy (~60-80yr) does not allow to firmly conclude on the causal effect of the AMV. We use a model approach to isolate the causal role of the AMV on the occurrence of extreme events over Europe and North America. We present experiments based on two GFDL global climate models, a low resolution version, CM2.1 and a higher resolution model for the atmospheric component, FLOR. In both model experiments sea surface temperatures in the North Atlantic sector are restored to the observed AMV pattern, while the other basins are left fully coupled. In order to explore and robustly isolate the AMV impacts on extreme events, we use large ensemble simulations (100 members for CM2.1 and 50 for FLOR) that we run for 20 years. We find that a positive phase of the AMV increases the frequency of occurrence of drought over North America and of extremely cold/warm conditions over Northern/Central Europe during winter/summer. Interestingly, we find that the AMV impacts on these extreme conditions are modulated by the Pacific response to the AMV itself. Members that develop a weak Pacific response show more extreme events over Europe whereas those that develop a strong Pacific response show more extreme events over North America.

  19. Condition Judgement of Dry Eye in Sicca Syndrome

    Institute of Scientific and Technical Information of China (English)

    1994-01-01

    In this paper, we presented 32 dry eyes of 16 random patients with primary Sicca Syndrome graded with rose bengal(rb), Break up time of tear film (BUT) and Schirmer 1 test (S1T). Of them, the lip biopsy and tear β2-M level were examined and overall studied. The results showed that the grade of dry eye was closely related with both the degree of lymphocyte infiltration of lip glands and level of tear β2-M, and indicated that our grading methed for dry eye based on rb, BUT and SIT is dependable, and the l...

  20. Extreme hydrothermal conditions at an active plate-bounding fault.

    Science.gov (United States)

    Sutherland, Rupert; Townend, John; Toy, Virginia; Upton, Phaedra; Coussens, Jamie; Allen, Michael; Baratin, Laura-May; Barth, Nicolas; Becroft, Leeza; Boese, Carolin; Boles, Austin; Boulton, Carolyn; Broderick, Neil G R; Janku-Capova, Lucie; Carpenter, Brett M; Célérier, Bernard; Chamberlain, Calum; Cooper, Alan; Coutts, Ashley; Cox, Simon; Craw, Lisa; Doan, Mai-Linh; Eccles, Jennifer; Faulkner, Dan; Grieve, Jason; Grochowski, Julia; Gulley, Anton; Hartog, Arthur; Howarth, Jamie; Jacobs, Katrina; Jeppson, Tamara; Kato, Naoki; Keys, Steven; Kirilova, Martina; Kometani, Yusuke; Langridge, Rob; Lin, Weiren; Little, Timothy; Lukacs, Adrienn; Mallyon, Deirdre; Mariani, Elisabetta; Massiot, Cécile; Mathewson, Loren; Melosh, Ben; Menzies, Catriona; Moore, Jo; Morales, Luiz; Morgan, Chance; Mori, Hiroshi; Niemeijer, Andre; Nishikawa, Osamu; Prior, David; Sauer, Katrina; Savage, Martha; Schleicher, Anja; Schmitt, Douglas R; Shigematsu, Norio; Taylor-Offord, Sam; Teagle, Damon; Tobin, Harold; Valdez, Robert; Weaver, Konrad; Wiersberg, Thomas; Williams, Jack; Woodman, Nick; Zimmer, Martin

    2017-06-01

    Temperature and fluid pressure conditions control rock deformation and mineralization on geological faults, and hence the distribution of earthquakes. Typical intraplate continental crust has hydrostatic fluid pressure and a near-surface thermal gradient of 31 ± 15 degrees Celsius per kilometre. At temperatures above 300-450 degrees Celsius, usually found at depths greater than 10-15 kilometres, the intra-crystalline plasticity of quartz and feldspar relieves stress by aseismic creep and earthquakes are infrequent. Hydrothermal conditions control the stability of mineral phases and hence frictional-mechanical processes associated with earthquake rupture cycles, but there are few temperature and fluid pressure data from active plate-bounding faults. Here we report results from a borehole drilled into the upper part of the Alpine Fault, which is late in its cycle of stress accumulation and expected to rupture in a magnitude 8 earthquake in the coming decades. The borehole (depth 893 metres) revealed a pore fluid pressure gradient exceeding 9 ± 1 per cent above hydrostatic levels and an average geothermal gradient of 125 ± 55 degrees Celsius per kilometre within the hanging wall of the fault. These extreme hydrothermal conditions result from rapid fault movement, which transports rock and heat from depth, and topographically driven fluid movement that concentrates heat into valleys. Shear heating may occur within the fault but is not required to explain our observations. Our data and models show that highly anomalous fluid pressure and temperature gradients in the upper part of the seismogenic zone can be created by positive feedbacks between processes of fault slip, rock fracturing and alteration, and landscape development at plate-bounding faults.

  1. Extreme hydrothermal conditions at an active plate-bounding fault

    Science.gov (United States)

    Sutherland, Rupert; Townend, John; Toy, Virginia; Upton, Phaedra; Coussens, Jamie; Allen, Michael; Baratin, Laura-May; Barth, Nicolas; Becroft, Leeza; Boese, Carolin; Boles, Austin; Boulton, Carolyn; Broderick, Neil G. R.; Janku-Capova, Lucie; Carpenter, Brett M.; Célérier, Bernard; Chamberlain, Calum; Cooper, Alan; Coutts, Ashley; Cox, Simon; Craw, Lisa; Doan, Mai-Linh; Eccles, Jennifer; Faulkner, Dan; Grieve, Jason; Grochowski, Julia; Gulley, Anton; Hartog, Arthur; Howarth, Jamie; Jacobs, Katrina; Jeppson, Tamara; Kato, Naoki; Keys, Steven; Kirilova, Martina; Kometani, Yusuke; Langridge, Rob; Lin, Weiren; Little, Timothy; Lukacs, Adrienn; Mallyon, Deirdre; Mariani, Elisabetta; Massiot, Cécile; Mathewson, Loren; Melosh, Ben; Menzies, Catriona; Moore, Jo; Morales, Luiz; Morgan, Chance; Mori, Hiroshi; Niemeijer, Andre; Nishikawa, Osamu; Prior, David; Sauer, Katrina; Savage, Martha; Schleicher, Anja; Schmitt, Douglas R.; Shigematsu, Norio; Taylor-Offord, Sam; Teagle, Damon; Tobin, Harold; Valdez, Robert; Weaver, Konrad; Wiersberg, Thomas; Williams, Jack; Woodman, Nick; Zimmer, Martin

    2017-06-01

    Temperature and fluid pressure conditions control rock deformation and mineralization on geological faults, and hence the distribution of earthquakes. Typical intraplate continental crust has hydrostatic fluid pressure and a near-surface thermal gradient of 31 ± 15 degrees Celsius per kilometre. At temperatures above 300-450 degrees Celsius, usually found at depths greater than 10-15 kilometres, the intra-crystalline plasticity of quartz and feldspar relieves stress by aseismic creep and earthquakes are infrequent. Hydrothermal conditions control the stability of mineral phases and hence frictional-mechanical processes associated with earthquake rupture cycles, but there are few temperature and fluid pressure data from active plate-bounding faults. Here we report results from a borehole drilled into the upper part of the Alpine Fault, which is late in its cycle of stress accumulation and expected to rupture in a magnitude 8 earthquake in the coming decades. The borehole (depth 893 metres) revealed a pore fluid pressure gradient exceeding 9 ± 1 per cent above hydrostatic levels and an average geothermal gradient of 125 ± 55 degrees Celsius per kilometre within the hanging wall of the fault. These extreme hydrothermal conditions result from rapid fault movement, which transports rock and heat from depth, and topographically driven fluid movement that concentrates heat into valleys. Shear heating may occur within the fault but is not required to explain our observations. Our data and models show that highly anomalous fluid pressure and temperature gradients in the upper part of the seismogenic zone can be created by positive feedbacks between processes of fault slip, rock fracturing and alteration, and landscape development at plate-bounding faults.

  2. Bridge Management Strategy Based on Extreme User Costs for Bridge Network Condition

    Directory of Open Access Journals (Sweden)

    Ladislaus Lwambuka

    2014-01-01

    Full Text Available This paper presents a practical approach for prioritization of bridge maintenance within a given bridge network. The maintenance prioritization is formulated as a multiobjective optimization problem where the simultaneous satisfaction of several conflicting objectives includes minimization of maintenance costs, maximization of bridge deck condition, and minimization of traffic disruption and associated user costs. The prevalence of user cost during maintenance period is twofold; the first case refers to the period of dry season where normally the traffic flow is diverted to alternative routes usually resurfaced to regain traffic access. The second prevalence refers to the absence of alternative routes which is often the case in the least developed countries; in this case the user cost referred to results from the waiting time while the traffic flow is put on hold awaiting accomplishment of the maintenance activity. This paper deals with the second scenario of traffic closure in the absence of alternative diversion routes which in essence results in extreme user cost. The paper shows that the multiobjective optimization approach remains valid for extreme cases of user costs in the absence of detour roads as often is the scenario in countries with extreme poor road infrastructure.

  3. Effect of green roofs on air temperature; measurement study of well-watered and dry conditions

    Science.gov (United States)

    Solcerova, Anna; van de Ven, Frans; Wang, Mengyu; van de Giesen, Nick

    2016-04-01

    Rapid urbanization and increasing number and duration of heat waves poses a need for understanding urban climate and ways to mitigate extremely high temperatures. One of repeatedly suggested and often investigated methods to moderate the so called urban heat island are green roofs. This study investigates several extensive green roofs in Utrecht (NL) and their effect on air temperature right above the roof surface. Air temperature was measured 15 and 30 cm above the roof surface and also in the substrate. We show that under normal condition is air above green roof, compared to white gravel roof, colder at night and warmer during day. This suggest that green roofs might help decrease air temperatures at night, when the urban heat island is strongest, but possibly contribute to high temperatures during daytime. We also measured situation when the green roofs wilted and dried out. Under such conditions green roof exhibits more similar behavior to conventional white gravel roof. Interestingly, pattern of soil temperature remains almost the same for both dry and well-prospering green roof, colder during day and warmer at night. As such, green roof works as a buffer of diurnal temperature changes.

  4. Effect of Drying Conditions on the Collapse-prone Wood of Eucalyptus urophylla

    Directory of Open Access Journals (Sweden)

    Lin Yang

    2014-10-01

    Full Text Available Collapse is considered one of the most severe defects that can occur during the drying of eucalyptus, resulting in drying degradation. Liquid tension is one of the reasons for the collapse. Some transient-collapse cells can be recovered upon the disappearance of liquid tension, when moisture content is reduced during the drying process. How to control collapse and help its recovery are key factors of drying technology. This supports the introduction of a kind of sequential drying technology to the drying process. Thus, several intermittent drying procedures were used in this study. Measurements of shrinkage and collapse were made on Eucalyptus urophylla under continuous drying as well as several kinds of intermittent drying. Key factors of the intermittent drying schedule, observed for their effect on collapse recovery, were the length of the drying periods and temperature during the intermittent periods. The microstructure of collapse under different drying schedules was examined at the cellular level using scanning electron microscopy (SEM. This confirmed that intermittent drying conditions can help collapsed cells recover more thoroughly than continuous drying conditions.

  5. Fast temperature spectrometer for samples under extreme conditions.

    Science.gov (United States)

    Zhang, Dongzhou; Jackson, Jennifer M; Zhao, Jiyong; Sturhahn, Wolfgang; Alp, E Ercan; Toellner, Thomas S; Hu, Michael Y

    2015-01-01

    We have developed a multi-wavelength Fast Temperature Readout (FasTeR) spectrometer to capture a sample's transient temperature fluctuations, and reduce uncertainties in melting temperature determination. Without sacrificing accuracy, FasTeR features a fast readout rate (about 100 Hz), high sensitivity, large dynamic range, and a well-constrained focus. Complimenting a charge-coupled device spectrometer, FasTeR consists of an array of photomultiplier tubes and optical dichroic filters. The temperatures determined by FasTeR outside of the vicinity of melting are, generally, in good agreement with results from the charge-coupled device spectrometer. Near melting, FasTeR is capable of capturing transient temperature fluctuations, at least on the order of 300 K/s. A software tool, SIMFaster, is described and has been developed to simulate FasTeR and assess design configurations. FasTeR is especially suitable for temperature determinations that utilize ultra-fast techniques under extreme conditions. Working in parallel with the laser-heated diamond-anvil cell, synchrotron Mössbauer spectroscopy, and X-ray diffraction, we have applied the FasTeR spectrometer to measure the melting temperature of (57)Fe0.9Ni0.1 at high pressure.

  6. Focusing adaptive-optics for neutron spectroscopy at extreme conditions

    Energy Technology Data Exchange (ETDEWEB)

    Simeoni, G. G., E-mail: ggsimeoni@outlook.com [Heinz Maier-Leibnitz Zentrum (MLZ), FRM II, Technical University of Munich, D-85748 Garching (Germany); Physics Department E13, Technical University of Munich, D-85748 Garching (Germany); Valicu, R. G. [Heinz Maier-Leibnitz Zentrum (MLZ), FRM II, Technical University of Munich, D-85748 Garching (Germany); Physics Department E13, Technical University of Munich, D-85748 Garching (Germany); Physics Department E21, Technical University of Munich, D-85748 Garching (Germany); Borchert, G. [Heinz Maier-Leibnitz Zentrum (MLZ), FRM II, Technical University of Munich, D-85748 Garching (Germany); Böni, P. [Physics Department E21, Technical University of Munich, D-85748 Garching (Germany); Rasmussen, N. G. [Nanoscience Center, Niels Bohr Institute, University of Copenhagen, Universitetsparken 5, DK-2100 Copenhagen (Denmark); Yang, F.; Kordel, T.; Holland-Moritz, D.; Kargl, F.; Meyer, A. [Institut für Materialphysik im Weltraum, Deutsches Zentrum für Luft- und Raumfahrt, D-51170 Köln (Germany)

    2015-12-14

    Neutron Spectroscopy employing extreme-conditions sample environments is nowadays a crucial tool for the understanding of fundamental scientific questions as well as for the investigation of materials and chemical-physical properties. For all these kinds of studies, an increased neutron flux over a small sample area is needed. The prototype of a focusing neutron guide component, developed and produced completely at the neutron source FRM II in Garching (Germany), has been installed at the time-of-flight (TOF) disc-chopper neutron spectrometer TOFTOF and came into routine-operation. The design is based on the compressed Archimedes' mirror concept for finite-size divergent sources. It represents a unique device combining the supermirror technology with Adaptive Optics, suitable for broad-bandwidth thermal-cold TOF neutron spectroscopy (here optimized for 1.4–10 Å). It is able to squeeze the beam cross section down to a square centimeter, with a more than doubled signal-to-background ratio, increased efficiency at high scattering angles, and improved symmetry of the elastic resolution function. We present a comparison between the simulated and measured beam cross sections, as well as the performance of the instrument within real experiments. This work intends to show the unprecedented opportunities achievable at already existing instruments, along with useful guidelines for the design and construction of next-generation neutron spectrometers.

  7. Orographic Signature on Multiscale Statistics of Extreme Rainfall: Conditional downscaling with emphasis on extremes

    Science.gov (United States)

    Foufoula-Georgiou, E.; Ebtehaj, M.

    2010-09-01

    Rainfall intensity and spatio-temporal patterns often show a strong dependency on the underlying terrain. The main objective of this work is to study the statistical signature imprinted by orography on the spatial structure of rainfall and its temporal evolution at multiple scales, with the aim to develop a consistent theoretical basis for conditional downscaling of precipitation given the topographic information of the underlying terrain. The results of an extensive analysis of the high resolution stage II Doppler radar data of the Rapidan storm, June 1995, over the Appalachian Mountains is reported in this study. The orographic signature on the elementary statistical structure of the precipitation fields is studied via a variable-intensity thresholding scheme. This signature is further explored at multiple scales via analysis of the dependence of precipitation fields on the underlying terrain both in Fourier and Wavelet domains. The Generalized Normal distribution is found to be a suitable probability model to explain the variability of the rainfall wavelet coefficients and its dependence on the underlying elevations. These results provide a new perspective for more accurate statistical downscaling of the orographic precipitation over complex terrain with emphasis on extremes.

  8. Have precipitation extremes and annual totals been increasing in the world's dry regions over the last 60 years?

    CERN Document Server

    Sippel, Sebastian; Heimann, Martin; Lange, Holger; Mahecha, Miguel D; van Oldenborgh, Geert Jan; Otto, Friederike E L; Reichstein, Markus

    2016-01-01

    Daily rainfall extremes and annual totals have increased in large parts of the global land area over the last decades. These observations are consistent with theoretical considerations of a warming climate. However, until recently these global tendencies have not been shown to consistently affect land regions with limited moisture availability. A recent study, published by Donat et al. (2016, Nature Climate Change, doi:10.1038/nclimate2941), now identified rapid increases in globally aggregated dry region daily extreme rainfall and annual rainfall totals. Here, we reassess the respective analysis and find that a) statistical artifacts introduced by the choice of the reference period prior to data standardization lead to an overestimation of the reported trends by up to 40%, and also that b) the definition of `dry regions of the globe' affect the reported globally aggregated trends in extreme rainfall. Using the same observational dataset, but accounting for the statistical artifacts and using alternative, wel...

  9. Extreme wind conditions for a Danish offshore site

    DEFF Research Database (Denmark)

    Hansen, Kurt S.

    2000-01-01

    This paper presents an analysis of extreme wind speed gust values measured at a shallow water offshore site and at a coastal onshore site in Denmark. An estimate of 50-year extreme values has been evaluated using a new statistical method. In addition a mean gust shape is determined, based on a la...

  10. Optimization of freeze drying conditions for purified pectinase from mango (Mangifera indica cv. Chokanan) peel

    National Research Council Canada - National Science Library

    Mehrnoush, Amid; Mustafa, Shuhaimi; Yazid, Abdul Manap Mohd

    2012-01-01

    Response surface methodology (RSM) along with central composite design (CCD) was applied to optimize the freeze drying conditions for purified pectinase from mango (Mangifera indica cv. Chokanan) peel...

  11. Seasonal Forecasts of Extreme Conditions for Wildland Fire Management in Alaska using NMME

    Science.gov (United States)

    Bhatt, U. S.; Bieniek, P.; Thoman, R.; York, A.; Ziel, R.

    2016-12-01

    The summer of 2015 was the second largest Alaska fire season since 1950 where approximately the land area of Massachusetts burned. The record fire year of 2004 resulted in 6.5 million acres burned and was costly from property loss (> 35M) and emergency personnel (> 17M). In addition to requiring significant resources, wildfire smoke impacts air quality in Alaska and downstream into North America. Fires in Alaska result from lightning strikes coupled with persistent (extreme) dry warm conditions in remote areas with limited fire management and the seasonal climate/weather determine the extent of the fire season in Alaska. Fire managers rely on weather/climate outlooks for allocating staff and resources from days to a season in advance. Though currently few tested products are available at the seasonal scale. Probabilistic forecasts of the expected seasonal climate/weather would aid tremendously in the planning process. Advanced knowledge of both lightning and fuel conditions would assist managers in planning resource allocation for the upcoming season. For fuel conditions, the Canadian Forest Fire Weather Index System (CFFWIS) has been used since 1992 because it better suits the Alaska fire regime than the standard US National Fire Danger Rating System (NFDRS). This CFFWIS is based on early afternoon values of 2-m air temperature, relative humidity, and 10-m winds and daily total precipitation. Extremes of these indices and the variables are used to calculate these indices will be defined in reference to fire weather for the boreal forest. The CFFWIS will be applied and evaluated for the NMME hindcasts. This study will evaluate the quality of the forecasts comparing the hindcast NMME CFFWIS to acres burned in Alaska. Spatial synoptic patterns in the NMME related to fire weather extremes will be constructed using self-organized maps and probabilities of occurrence will be evaluated against acres burned.

  12. Thorium Chemistry in Oxo-Tellurium System under Extreme Conditions.

    Science.gov (United States)

    Xiao, Bin; Kegler, Philip; Bosbach, Dirk; Alekseev, Evgeny V

    2017-03-06

    Through the use of a high-temperature/high-pressure synthesis method, four thorium oxo-tellurium compounds with different tellurium valence states were isolated. The novel inorganic phases illustrate the intrinsic complexity of the actinide tellurium chemistry under extreme conditions of pressure and temperature. Th2Te3O11 is the first instance of a mixed-valent oxo-tellurium compound, and at the same time, Te exhibits three different coordination environments (Te(IV)O3, Te(IV)O4, and Te(VI)O6) within a single structure. These three types of Te polyhedra are further fused together, resulting in a [Te3O11](8-) fragment. Na4Th2(Te(VI)3O15) and K2Th(Te(VI)O4)3 are the first alkaline thorium tellurates described in the literature. Both compounds are constructed from ThO9 tricapped trigonal prisms and Te(VI)O6 octahedra. Na4Th2(Te(VI)3O15) is a three-dimensional framework based on Th2O15 and Te2O10 dimers, while K2Th(Te(VI)O4)3 contains tungsten oxide bronze like Te layers linked by ThO9 polyhedra. The structure of β-Th(Te(IV)O3)(SO4) is built from infinite thorium chains cross-linked by Te(IV)O3(2-) and SO4(2-) anions. Close structural analysis suggests that β-Th(Te(IV)O3)(SO4) is highly related to the structure of α-Th(SeO4)2. Additionally, the Raman spectra are recorded and the characteristic peaks are assigned based on a comparison of reported tellurites or tellurates.

  13. Final Report for Project. Quark matter under extreme conditions

    Energy Technology Data Exchange (ETDEWEB)

    Incera, Vivian [Univ. of Texas, El Paso, TX (United States); Ferrer, Efrain [Univ. of Texas, El Paso, TX (United States)

    2015-12-31

    The results obtained in the two years of the grant have served to shine new light on several important questions about the phases of quantum chromodynamics (QCD) under extreme conditions that include quark matter at high density, as well quark-gluon plasma at high temperatures, both in the presence of strong magnetic fields. The interest in including an external magnetic field on these studies is motivated by the generation of large magnetic fields in off-central heavy-ion collisions and by their common presence in astrophysical compact objects, the two scenarios where the physics of quark matter becomes relevant. The tasks carried out in this DOE project led us, among other things, to discover the first connection between the physics of very dense quark matter and novel materials as for instance topological insulators and Weyl semimetals; they allowed us to find a physical explanation for and a solution to a standing puzzle in the apparent effect of a magnetic field on the critical temperature of the QCD chiral transition; and they led us to establish by the first time that the core of the observed two-solar-mass neutron stars could be made up of quark matter in certain inhomogeneous chiral phases in a magnetic field and that this was consistent with current astrophysical observations. A major goal established by the Nuclear Science Advisory committee in its most recent report “Reaching for the Horizon” has been “to truly understand how nuclei and strongly interacting matter in all its forms behave and can predict their behavior in new settings.” The results found in this DOE project have all contributed to address this goal, and thus they are important for advancing fundamental knowledge in the area of nuclear physics and for enhancing our understanding of the role of strong magnetic fields in the two settings where they are most relevant, neutron stars and heavy-ion collisions.

  14. Extreme Conditioning Programs: Potential Benefits and Potential Risks.

    Science.gov (United States)

    Knapik, Joseph J

    2015-01-01

    CrossFit, Insanity, Gym Jones, and P90X are examples of extreme conditioning programs (ECPs). ECPs typically involve high-volume and high-intensity physical activities with short rest periods between movements and use of multiple joint exercises. Data on changes in fitness with ECPs are limited to CrossFit investigations that demonstrated improvements in muscle strength, muscular endurance, aerobic fitness, and body composition. However, no study has directly compared CrossFit or other ECPs to other more traditional forms of aerobic and resistance training within the same investigation. These direct comparisons are needed to more adequately evaluate the effectiveness of ECPs. Until these studies emerge, the comparisons with available literature suggest that improvements in CrossFit, in terms of muscular endurance (push-ups, sit-ups), strength, and aerobic capacity, appear to be similar to those seen in more traditional training programs. Investigations of injuries in ECPs are limited to two observational studies that suggest that the overall injury rate is similar to that seen in other exercise programs. Several cases of rhabdomyolysis and cervical carotid artery dissections have been reported during CrossFit training. The symptoms, diagnosis, and treatment of these are reviewed here. Until more data on ECPs emerge, physical training should be aligned with US Army doctrine. If ECPs are included in exercise programs, trainers should (1) have appropriate training certifications, (2) inspect exercise equipment regularly to assure safety, (3) introduce ECPs to new participants, (4) ensure medical clearance of Soldiers with special health problems before participation in ECPs, (4) tailor ECPs to the individual Soldier, (5) adjust rest periods to optimize recovery and reduce fatigue, (6) monitor Soldiers for signs of overtraining, rhabdomyolysis, and other problems, and (7) coordinate exercise programs with other unit training activities to eliminate redundant activities

  15. Lower Extremity Overuse Conditions Affecting Figure Skaters During Daily Training

    National Research Council Canada - National Science Library

    Campanelli, Valentina; Piscitelli, Francesco; Verardi, Luciano; Maillard, Pauline; Sbarbati, Andrea

    2015-01-01

    Background Most ice figure skaters train and compete with ongoing issues in the lower extremities, which are often overlooked by the skaters and considered injuries only when they prevent the athletes from skating...

  16. Uncertainties in extreme precipitation under climate change conditions

    DEFF Research Database (Denmark)

    Sunyer Pinya, Maria Antonia

    of adaptation strategies, but these changes are subject to uncertainties. The focus of this PhD thesis is the quantification of uncertainties in changes in extreme precipitation. It addresses two of the main sources of uncertainty in climate change impact studies: regional climate models (RCMs) and statistical...... by extreme precipitation pose a threat to human life and cause high economic losses for society. Thus, strategies to adapt to changes in extreme precipitation are currently being developed and established worldwide. Information on the expected changes in extreme precipitation is required for the development...... downscaling methods (SDMs). RCMs provide information on climate change at the regional scale. SDMs are used to bias-correct and downscale the outputs of the RCMs to the local scale of interest in adaptation strategies. In the first part of the study, a multi-model ensemble of RCMs from the European ENSEMBLES...

  17. Cosmetic Cleansing Oil Absorption by Soft Contact Lenses in Dry and Wet Conditions.

    Science.gov (United States)

    Tsukiyama, Junko; Miyamoto, Yuko; Kodama, Aya; Fukuda, Masahiko; Shimomura, Yoshikazu

    2017-09-01

    Previous reports showed that cosmetic cleansing oil for removing makeup, which contains mineral oil and surfactant, can deform some silicone hydrogel contact lenses (SHCLs) when applied directly to the lenses, although plasma-coated SHCLs (lotrafilcon A and B) were not affected. In the present study, we investigated hydrogel lenses and SHCLs in both wet and dry conditions. Several brands of hydrogel and SHCLs were immersed in a cleansing oil solution containing Sudan Black B for 5 min under wet and dry conditions. The lenses under the wet condition were simply picked up from the saline, whereas those under the dry condition were blotted with paper wipes. After immersing, the excess solution remaining on the lenses was removed by finger rubbing with a multipurpose solution. The lenses were then examined using a stereomicroscope, and their mean brightness was measured and compared. The cosmetic cleansing oil was not absorbed by the hydrogel lenses under wet or dry conditions. However, four of seven brands of SHCLs absorbed the cosmetic cleansing oil under both conditions (dry and wet), whereas asmofilcon A absorbed it only under the dry condition. Lotrafilcon B and delefilcon A did not absorb cleansing oil even under the dry condition. Hydrogel lenses resist cosmetic cleansing oil. However, SHCLs have different degrees of resistance depending on the lens material. Some SHCLs absorbed cosmetic cleansing oil more under dry conditions than under wet conditions.

  18. Response of Groundwater to Climate Change under Extreme Climate Conditions in North China Plain

    Institute of Scientific and Technical Information of China (English)

    Ying Zhang; Jincui Wang; Jihong Jing; Jichao Sun

    2014-01-01

    The North China Plain (NCP) is one of the water shortage areas of China. Lack of water resources restricted the economic and social development of North China area and resulted in deterio-ration of ecosystem and natural environment. Influenced by the climate change and human activities, the water circulation of NCP was largely changed and the crisis of water resources was aggravated. Therefore, it is important to study the features of the extreme climate and the response mechanism of groundwater to climate change. We analyzed the trend of climate change and extreme climate features in the past 60 years based on the monitoring data of meteorological stations. And then the response characteristics of groundwater to climate change were discussed. The average temperature of NCP was in an obviously upward trend. The overall precipitation variation was in a downward trend. The cli-mate change in this area showed a warming-drying trend. The intensity of extreme precipitation dis-played a trend of declining and then increasing from north to south as well as declining from eastern coastal plain to the piedmont plain. Grey correlation degree analysis indicated that groundwater depth had a close relationship with precipitation and human activities in NCP. The response of groundwater level to precipitation differed from the piedmont alluvial-pluvial plain to the coastal plain. The response was more obvious in the coastal plain than the piedmont alluvial-pluvial plain and the middle plain. The precipitation influenced the groundwater depth both directly and indirectly. Under the condition of extreme precipitation, the impact would aggravate, in the forms of rapid or lag raise of groundwater levels.

  19. OPTIMUM DRYING PROCESS. Best drying conditions to grind fruits and vegetables

    OpenAIRE

    Pina Laguna, Meritxell

    2013-01-01

    World’s population is increasing annually, thereby increasing world’s food demand. Considering current trends, changes in food production must be done in order to meet the estimated future demand. This problem and its possible solutions such as drying or pulverizing the foods, in which this thesis is focused on, are described in detail below.

  20. The Reactivity of Energetic Materials At Extreme Conditions

    Energy Technology Data Exchange (ETDEWEB)

    Fried, L E

    2006-10-23

    shock conditions, for example, energetic materials undergo rapid heating to a few thousand degrees and are subjected to a compression of hundreds of kilobars, resulting in almost 30% volume reduction. Complex chemical reactions are thus initiated, in turn releasing large amounts of energy to sustain the detonation process. Clearly, understanding of the various chemical events at these extreme conditions is essential in order to build predictive material models. Scientific investigations into the reactive process have been undertaken over the past two decades. However, the sub-{micro}s time scale of explosive reactions, in addition to the highly exothermic conditions of an explosion, make experimental investigation of the decomposition pathways difficult at best. More recently, new computational approaches to investigate condensed-phase reactivity in energetic materials have been developed. Here we focus on two different approaches to condensed-phase reaction modeling: chemical equilibrium methods and atomistic modeling of condensed-phase reactions. These are complementary approaches to understanding the chemical reactions of high explosives. Chemical equilibrium modeling uses a highly simplified thermodynamic picture of the reaction process, leading to a convenient and predictive model of detonation and other decomposition processes. Chemical equilibrium codes are often used in the design of new materials, both at the level of synthesis chemistry and formulation. Atomistic modeling is a rapidly emerging area. The doubling of computational power approximately every 18 months has made atomistic condensed-phase modeling more feasible. Atomistic calculations employ far fewer empirical parameters than chemical equilibrium calculations. Nevertheless, the atomistic modeling of chemical reactions requires an accurate global Born-Oppenheimer potential energy surface. Traditionally, such a surface is constructed by representing the potential energy surface with an analytical fit

  1. Impacts of extreme hydro-meteorological conditions on ecosystem functioning and productivity patterns across Australia

    Science.gov (United States)

    Huete, Alfredo; Ma, Xuanlong; Xie, Zunyi; Restrepo-Coupe, Natalia; Ponce-Campos, Guillermo

    2016-04-01

    As Earth's climate continues to change, the frequency and intensity of warm droughts, extreme precipitation patterns, and heat waves will alter in potentially different ways, ecosystem structure and functioning with major impacts on carbon and water balance, and food security. The extreme hydro-meteorological conditions that are presently impacting Australia approach those anticipated with future climate change and thus provide unique opportunities to study ecological sensitivity and functional responses and cross-biome productivity changes using contemporary, in-situ and satellite observational datasets. Here, we combined satellite vegetation index products from MODIS and AVHRR, total water storage (TWS) from the GRACE twin satellites, precipitation data and in-situ tower flux measurements to characterise ecosystem sensitivity, and analyse climate change impacts on ecosystem productivity and resilience. Recent advances in eddy covariance tower flux measurements and spatially contiguous remote sensing data provide innovative and promising capabilities to extend ecosystem functioning and productivity studies from local to regional and continental scales. In general, Australia exhibited ecosystem-level shifts in water demands with water availability across wet and dry years, and over all biomes analysed (arid grasslands to humid forests). In the drier years, higher ecosystem water use efficiencies (WUEe) enabled plants to maintain higher levels of productivity than would otherwise be expected for the lower amounts of rainfall and available water. Further, there were unique, functional class-specific coping strategies to drought and water availability. With prolonged warm drought conditions, biomes became increasingly water-limited and WUEe continued to increase until reaching a 'dry edge' threshold, a cross biome maximum WUEe, that cannot be sustained with further reductions in water availability and could potentially break down ecosystem resilience and induce

  2. Matter in Extreme Conditions Instrument - Conceptual Design Report

    Energy Technology Data Exchange (ETDEWEB)

    Boyce, R.F.; Boyce, R.M.; Haller, G.; Hastings, J.B.; Hays, G.; Lee, H.J.; /SLAC; Lee, R.W.; /LLNL, Livermore; Nagler, B.; /Rutherford; Scharfenstein, M.; Marsh, D.; White, W.E.; /SLAC

    2009-12-09

    The SLAC National Accelerator Laboratory (SLAC), in collaboration with Argonne National Laboratory (ANL), Lawrence Livermore National Laboratory (LLNL), and the University of California at Los Angeles (UCLA), is constructing a Free-Electron Laser (FEL) research facility. The FEL has already met its performance goals in the wavelength range 1.5 nm - 0.15 nm. This facility, the Linac Coherent Light Source (LCLS), utilizes the SLAC 2-Mile Linear Accelerator (linac) and will produce sub-picosecond pulses of short wavelength X-rays with very high peak brightness and almost complete transverse coherence. The final one-third of the SLAC linac is used as the source of electrons for the LCLS. The high energy electrons are transported across the SLAC Research Yard, into a tunnel which houses a long undulator. In passing through the undulator, the electrons are bunched by the force of their own synchrotron radiation and produce an intense, monochromatic, spatially coherent beam of X-rays. By varying the electron energy, the FEL X-ray wavelength is tunable from 1.5 nm to 0.15 nm. The LCLS includes two experimental halls as well as X-ray optics and infrastructure necessary to create a facility that can be developed for research in a variety of disciplines such as atomic physics, materials science, plasma physics and biosciences. This Conceptual Design Report, the authors believe, confirms the feasibility of designing and constructing an X-ray instrument in order to exploit the unique scientific capability of LCLS by creating extreme conditions and study the behavior of plasma under those controlled conditions. This instrument will address the Office of Science, Fusion Energy Sciences, mission objective related to study of Plasma and Warm Dense Matter as described in the report titled LCLS, the First Experiments, prepared by the LCLS Scientific Advisory Committee (SAC) in September 2000. The technical objective of the LCLS Matter in Extreme Conditions (MEC) Instrument project is

  3. Matter in Extreme Conditions Instrument - Conceptual Design Report

    Energy Technology Data Exchange (ETDEWEB)

    Boyce, R.F.; Boyce, R.M.; Haller, G.; Hastings, J.B.; Hays, G.; Lee, H.J.; /SLAC; Lee, R.W.; /LLNL, Livermore; Nagler, B.; /Rutherford; Scharfenstein, M.; Marsh, D.; White, W.E.; /SLAC

    2009-12-09

    The SLAC National Accelerator Laboratory (SLAC), in collaboration with Argonne National Laboratory (ANL), Lawrence Livermore National Laboratory (LLNL), and the University of California at Los Angeles (UCLA), is constructing a Free-Electron Laser (FEL) research facility. The FEL has already met its performance goals in the wavelength range 1.5 nm - 0.15 nm. This facility, the Linac Coherent Light Source (LCLS), utilizes the SLAC 2-Mile Linear Accelerator (linac) and will produce sub-picosecond pulses of short wavelength X-rays with very high peak brightness and almost complete transverse coherence. The final one-third of the SLAC linac is used as the source of electrons for the LCLS. The high energy electrons are transported across the SLAC Research Yard, into a tunnel which houses a long undulator. In passing through the undulator, the electrons are bunched by the force of their own synchrotron radiation and produce an intense, monochromatic, spatially coherent beam of X-rays. By varying the electron energy, the FEL X-ray wavelength is tunable from 1.5 nm to 0.15 nm. The LCLS includes two experimental halls as well as X-ray optics and infrastructure necessary to create a facility that can be developed for research in a variety of disciplines such as atomic physics, materials science, plasma physics and biosciences. This Conceptual Design Report, the authors believe, confirms the feasibility of designing and constructing an X-ray instrument in order to exploit the unique scientific capability of LCLS by creating extreme conditions and study the behavior of plasma under those controlled conditions. This instrument will address the Office of Science, Fusion Energy Sciences, mission objective related to study of Plasma and Warm Dense Matter as described in the report titled LCLS, the First Experiments, prepared by the LCLS Scientific Advisory Committee (SAC) in September 2000. The technical objective of the LCLS Matter in Extreme Conditions (MEC) Instrument project is

  4. Thin film composite nanofiltration membranes for extreme conditions

    NARCIS (Netherlands)

    Dalwani, Mayur Ramesh

    2011-01-01

    The research presented in this thesis focuses on development and performance evaluation of thin film composite (TFC) nanofiltration (NF) membranes, with special attention to extreme pH applications. In Chapter 2 a new method that allows molecular weight cut off (MWCO) characterization of NF membran

  5. Reducing uncertainty in prediction of dune erosion during extreme conditions

    NARCIS (Netherlands)

    Den Heijer, C.; Reniers, A.J.H.M.; Van de Graaff, J.; Van Gelder, P.H.A.J.M.

    2008-01-01

    Coastal dunes protect low lying coastal areas against the sea. Extreme waves and water levels during severe storms may cause breaching of the dunes. Consequently, serious damage due to flooding and direct wave attack could occur, resulting in loss of life and property. Proper coastal management impl

  6. A Comparative Analysis of Primary and Extreme Characteristics of Dry or Wet Status between Asia and North America

    Institute of Scientific and Technical Information of China (English)

    HUA Lijuan; MA Zhuguo; ZHONG Linhao

    2011-01-01

    In this study, the Palmer Drought Severity Index (PDSI) was used to analyze the average and extreme dry/wet states of Asia and North America from 1953 to 2003. The results indicate that the two continents underwent drying trends during this period. Compared with North America, Asia showed more severe drought trends. However, more significant and regular seasonal variation for drought was found in North America. The driest regions in Asia were located in the northern region of China, Mongolia, and eastern mid-Siberian plateau. Most regions in central North America were relatively wetter than other regions.The northern and southwestern regions of North America, as well as the Atlantic and Pacific coastal areas,experienced the most drought during this period. A sharp increase of the drought area and the number of extreme drought events took place from 1997 to 2003 in both Asia and North America. Severe drought events were more likely to occur during the summer on both continents. Asia had the most extreme drought events during July, but North America reached its highest drought frequency from June to September. In Asia, a persistent increasing trend of extreme drought emerged throughout the studied period. However,a more complex evolution of drought emerged in North America: a decreasing trend appeared before the mid-1960s and an increasing trend appeared after the late 1970s. A relatively steady dry/wet status was observed between the mid-1960s and the late 1970s. The role of exceptional, extreme drought events with respect to the La Nifia event was considered during 1997-2003.

  7. OPTIMIZATION OF MICROWAVE AND AIR DRYING CONDITIONS OF QUINCE (CYDONIA OBLONGA, MILLER USING RESPONSE SURFACE METHODOLOGY

    Directory of Open Access Journals (Sweden)

    Cem Baltacioglu

    2015-03-01

    Full Text Available Effects of slice thickness of quince (Cydonia oblonga Miller , microwave incident power and air drying temperature on antioxidant activity and total phenolic content of quince were investigated during drying in microwave and air drying. Optimum conditions were found to be: i for microwave drying, 285 W and 4.14 mm thick (maximum antioxidant activity and 285 W and 6.85 mm thick (maximum total phenolic content, and ii for air drying, 75 ºC and 1.2 mm thick (both maximum antioxidant activity and total phenolic content. Drying conditions were optimized by using the response surface methodology. 13 experiments were carried out considering incident microwave powers from 285 to 795 W, air temperature from 46 to 74 ºC and slice thickness from 1.2 to 6.8 mm.

  8. Have precipitation extremes and annual totals been increasing in the world's dry regions over the last 60 years?

    Science.gov (United States)

    Sippel, Sebastian; Zscheischler, Jakob; Heimann, Martin; Lange, Holger; Mahecha, Miguel D.; van Oldenborgh, Geert Jan; Otto, Friederike E. L.; Reichstein, Markus

    2017-01-01

    Daily precipitation extremes and annual totals have increased in large parts of the global land area over the past decades. These observations are consistent with theoretical considerations of a warming climate. However, until recently these trends have not been shown to consistently affect dry regions over land. A recent study, published by Donat et al. (2016), now identified significant increases in annual-maximum daily extreme precipitation (Rx1d) and annual precipitation totals (PRCPTOT) in dry regions. Here, we revisit the applied methods and explore the sensitivity of changes in precipitation extremes and annual totals to alternative choices of defining a dry region (i.e. in terms of aridity as opposed to precipitation characteristics alone). We find that (a) statistical artifacts introduced by data pre-processing based on a time-invariant reference period lead to an overestimation of the reported trends by up to 40 %, and that (b) the reported trends of globally aggregated extremes and annual totals are highly sensitive to the definition of a dry region of the globe. For example, using the same observational dataset, accounting for the statistical artifacts, and based on different aridity-based dryness definitions, we find a reduction in the positive trend of Rx1d from the originally reported +1.6 % decade-1 to +0.2 to +0.9 % decade-1 (period changes for 1981-2010 averages relative to 1951-1980 are reduced to -1.32 to +0.97 % as opposed to +4.85 % in the original study). If we include additional but less homogenized data to cover larger regions, the global trend increases slightly (Rx1d: +0.4 to +1.1 % decade-1), and in this case we can indeed confirm (partly) significant increases in Rx1d. However, these globally aggregated estimates remain uncertain as considerable gaps in long-term observations in the Earth's arid and semi-arid regions remain. In summary, adequate data pre-processing and accounting for uncertainties regarding the definition of dryness are

  9. EFFECT OF MECHANICAL CONDITIONING ON THIN-LAYER DRYING OF ENERGY SORGHUM (Sorghum bicolor (L.) Moench)

    Energy Technology Data Exchange (ETDEWEB)

    Ian J. Bonner; Kevin L. Kenney

    2012-10-01

    Cellulosic energy varieties of Sorghum bicolor (L.) Moench show promise as a bioenergy feedstock, however, high moisture content at the time of harvest results in unacceptable levels of degradation when stored in aerobic conditions. To safely store sorghum biomass for extended periods in baled format, the material must be dried to inhibit microbial growth. One possible solution is allowing the material to dry under natural in-field conditions. This study examines the differences in thin-layer drying rates of intact and conditioned sorghum under laboratory-controlled temperatures and relative humidity levels (20 degrees C and 30 degrees C from 40% to 85% relative humidity), and models experimental data using the Page’s Modified equation. The results demonstrate that conditioning drastically accelerates drying times. Relative humidity had a large impact on the time required to reach a safe storage moisture content for intact material (approximately 200 hours at 30 degrees C and 40% relative humidity and 400 hours at 30 degrees C and 70% relative humidity), but little to no impact on the thin-layer drying times of conditioned material (approximately 50 hours for all humidity levels < 70% at 30 degrees C). The drying equation parameters were influenced by temperature, relative humidity, initial moisture content, and material damage, allowing drying curves to be empirically predicted. The results of this study provide valuable information applicable to the agricultural community and to future research on drying simulation and management of energy sorghum.

  10. Combined effects of Fenton peroxidation and CaO conditioning on sewage sludge thermal drying.

    Science.gov (United States)

    Liu, Huan; Liu, Peng; Hu, Hongyun; Zhang, Qiang; Wu, Zhenyu; Yang, Jiakuan; Yao, Hong

    2014-12-01

    Joint application of Fenton's reagent and CaO can dramatically enhance sludge dewaterability, thus are also likely to affect subsequent thermal drying process. This study investigated the synergistic effects of the two conditioners on the thermal drying behavior of sewage sludge and the emission characteristics of main sulfur-/nitrogen-containing gases. According to the results, Fenton peroxidation combined with CaO conditioning efficiently promoted sludge heat transfer, reduced the amounts of both free and bound water, and created porous structure in solids to provide evaporation channels, thus producing significant positive effects on sludge drying performance. In this case, the required time for drying was shortened to one-third. Additionally, joint usage of Fenton's reagent and CaO did not increase the losses of organic matter during sludge drying process. Meanwhile, they facilitated the formation of sulfate and sulfonic acid/sulfone, leading to sulfur retention in dried sludge. Both of Fenton peroxidation and CaO conditioning promoted the oxidation, decomposition, and/or dissolution of protein and inorganic nitrogen in sludge pre-treatment. As a consequence, the emissions of sulfurous and nitrogenous gases from dewatered sludge drying were greatly suppressed. These indicate that combining Fenton peroxidation with CaO conditioning is a promising strategy to improve drying efficiency of sewage sludge and to control sulfur and nitrogen contaminants during sludge thermal drying process.

  11. Cosmic Matter under Extreme Conditions: CSQCD II Summary

    CERN Document Server

    Wambach, Jochen

    2009-01-01

    After the first meeting in Copenhagen in 2001 QSQCD II is the second workshop in this series dealing with cosmic matter at very high density and its astrophysical implications. The aim is to bring together reseachers in the physics of compact stars, both theoretical and observational. Consequently a broad range of topics was presented, reviewing extremely energetic cosmological events and their relation to the high-density equation of state of strong-interaction matter. This summary elucidates recent progress in the field, as presented by the participants, and comments on pertinent questions for future developments.

  12. An effective, cosmetically acceptable, novel hydro-gel emollient for the management of dry skin conditions.

    Science.gov (United States)

    Wynne, A; Whitefield, M; Dixon, A J; Anderson, S

    2002-06-01

    A novel hydro-gel emollient (Doublebase) has been developed with improved moisturizing effects. To test this novel hydro-gel for its moisturizing effect, for its potential to cause skin irritancy/allergy and for its clinical effectiveness and acceptability in dry skin conditions. Skin hydration (corneometry) and trans-epidermal water loss (TEWL) studies with a single application in 18 volunteers confirmed its efficacy (p effectiveness of Doublebase was demonstrated in an open study of 78 patients with dry skin conditions. Doublebase may be considered a suitable preparation that can be used effectively by most patients with dry skin conditions.

  13. Interactions between formulation and spray drying conditions related to survival of Lactobacillus plantarum WCFS1

    NARCIS (Netherlands)

    Perdana, J.A.; Fox, M.B.; Siwei, C.; Boom, R.M.; Schutyser, M.A.I.

    2014-01-01

    Protective solid carriers are commonly added to probiotic cultures prior to drying. Their formulation is not trivial and depends on the drying conditions applied. In this study, we systematically investigated the influence of formulation parameters on the survival of Lactobacillus plantarum WCFS1 af

  14. Interactions between formulation and spray drying conditions related to survival of Lactobacillus plantarum WCFS1

    NARCIS (Netherlands)

    Perdana, J.A.; Fox, M.B.; Siwei, C.; Boom, R.M.; Schutyser, M.A.I.

    2014-01-01

    Protective solid carriers are commonly added to probiotic cultures prior to drying. Their formulation is not trivial and depends on the drying conditions applied. In this study, we systematically investigated the influence of formulation parameters on the survival of Lactobacillus plantarum WCFS1

  15. Effect of drying conditions on the physical properties of impregnated orange peel

    Directory of Open Access Journals (Sweden)

    K. Manjarres-Pinzon

    2013-09-01

    Full Text Available Orange peel represents approximately 30-40 g/100g of the fresh fruit weight and could be used to develop value-added products. Hence, this study aims to evaluate the effects of drying conditions on the physical properties of orange peel impregnated with sucrose solution. The response surface method (RSM was used to optimize two parameters: drying temperature (35-55 ºC and air flow rate (2-3 m/s. The measured responses used to determine the effect of dying process conditions were: moisture content. drying time. total soluble solids. color and hardness. The dried orange peels from the optimal process were subjected to a sensory test by 60 consumers. The optimum conditions for the drying of orange peels were determined to obtain minimum hardness, moisture content and drying time for a w values below 0.6. The optimum conditions were found to be a dying temperature of 52.3 ºC and air flow rate of 2.0 m/s. At this point, drying time, hardness and moisture content were found to be 20 h, 78.4 N and 7.6%, respectively. The sensory results showed that consumers aged over 30 years old accepted well the dried orange peel.

  16. Evaluation of bioactive compounds and bioactivities of soybean dried by different methods and conditions.

    Science.gov (United States)

    Niamnuy, Chalida; Nachaisin, Mali; Laohavanich, Juckamas; Devahastin, Sakamon

    2011-12-01

    Soybean has attracted significant research and commercial interests due to its many health-promoting bioactive compounds, especially isoflavones (β-glucosides, malonyl-β-glucosides, acetyl-β-glucosides and aglycones). Isoflavones possess antioxidant activity and α-glucosidase inhibitory activity, which has proved effective in the treatment of type 2 diabetes mellitus. Prior to its use, however, soybean needs to be dried to extend its storage life and to prepare the material for subsequent food or pharmaceutical processing. The present study investigated the effects of drying methods and conditions on the drying characteristics, isoflavones, antioxidant activity and α -glucosidase inhibitory activity of dried soybean. Hot-air fluidized bed drying (HAFBD), superheated-steam fluidized bed drying (SSFBD) and gas-fired infrared combined with hot air vibrating drying (GFIR-HAVD) were carried out at various drying temperatures (50, 70, 130 and150°C). The results showed that higher drying temperatures led to higher drying rates and higher levels of β-glucosides and antioxidant activity, but to lower levels of malonyl-β-glucosides, acetyl-β-glucosides and total isoflavones. At the same drying temperature GFIR-HAVD resulted in the highest drying rates and the highest levels of β-glucosides, aglycones and total isoflavones, antioxidant activity as well as α-glucosidase inhibitory activity of dried soybean. A drying temperature of 130°C gave the highest levels of aglycones and α-glucosidase inhibitory activity in all cases. The relationships between all the studied parameters were monitored and simple correlations between them were determined. Copyright © 2011 Elsevier Ltd. All rights reserved.

  17. Investigation of the Variability and Implications of Meteorological Dry/Wet Conditions in the Poyang Lake Catchment, China, during the Period 1960–2010

    Directory of Open Access Journals (Sweden)

    Xu-chun Ye

    2015-01-01

    Full Text Available This paper presents a quantitative investigation of the variability of meteorological dry/wet conditions of the Poyang Lake catchment during 1960–2010 by using the standardized precipitation-evapotranspiration index (SPEI based on daily observations of 14 meteorological stations across the catchment. Extending from previous studies, the background of the encounter and overlap of multitimescales of meteorological dry/wet episodes for several severe drought and flood events were discussed. In addition, the possible impacts of temperature changes on dry/wet variability were also examined by the comparison of SPEI and standardized precipitation index (SPI variations at multitimescales during the study period. Major results show that the occurrence of dry/wet condition has become increasingly frequent in the recent two decades, especially the extreme wet episodes in 1990s and the extreme dry episodes in 2000s. Historically, the encounter and overlap of multitimescales of meteorological dry/wet episodes plays an important role in the occurrence of several severe drought and flood events. The study concluded that the impact of temperature anomaly to the dry/wet variability cannot be neglected.

  18. EXISTENCE OF EXTREME SOLUTION TO FIRST-ORDER IMPULSIVE DIFFERENTIAL EQUATIONS WITH NONLINEAR BOUNDARY CONDITIONS

    Institute of Scientific and Technical Information of China (English)

    2011-01-01

    This paper is concerned with the existence of extreme solutions to three-point boundary value problems with nonlinear boundary conditions for a class of first order impulsive differential equations. We obtain suficient conditions for the existence of extreme solutions by the upper and lower solutions method coupled with a monotone iterative technique.

  19. Rational Calibration of Four IEC 61400-1 Extreme External Conditions

    DEFF Research Database (Denmark)

    Larsen, Gunner Chr.; Hansen, Kurt Schaldemose

    2008-01-01

    Based on a set of asymptotic statistical models on closed form this paper presents a rational and consistent calibration of four extreme external conditions defined in the International Electrotechnical Commission (IEC) 61400-1 standard: extreme operating gust, extreme wind shear, extreme coherent...... gust with direction change and extreme wind direction change. These four extreme external conditions are used in the definition of six of the IEC 61400-1 ultimate load cases. The statistical models are based on simple and easily accessible mean wind speed and turbulence characteristics...... of the atmospheric boundary layer. Using the wind climate characteristics prescribed in the IEC 61400-1 standard as input to the set of statistical models ensures consistency between the specified wind climate and the proposed extreme gust magnitudes. Differences and equalities between the present IEC specifications...

  20. Functional and physicochemical properties of whole egg powder: effect of spray drying conditions

    OpenAIRE

    2010-01-01

    Pasteurized liquid whole egg was subjected to spray drying to determine the effect of spray drying conditions on moisture content, water activity, peroxide value, emulsion stability, gel texture, foaming stability and colour change of the powder product. Drying process was carried out in a pilot scale spray dryer (Mobile Minor Niro-Atomizer, Denmark). The inlet (165–195 °C) and outlet air temperatures (60–80 °C) and the atomization pressure (196–392 kPa) were investigated as spray drying proc...

  1. Effect of drying conditions on crystallinity of amylose nanoparticles prepared by nanoprecipitation.

    Science.gov (United States)

    Yan, Xiaoxia; Chang, Yanjiao; Wang, Qian; Fu, Youjia; Zhou, Jiang

    2017-04-01

    In this study, amylose nanoparticles prepared by nanoprecipitation were dried at different conditions. The crystalline structure, crystallinity, re-dispersibility and morphological characteristic of the amylose nanoparticles after drying were investigated. X-ray diffraction analysis revealed that the V-type crystalline structure of the amylose nanoparticles formed in the drying process instead of the precipitation process, and drying condition significantly affects the crystallinity. The temperature cycles drying at 4°C and 40°C considerably increased crystallinity of the amylose nanoparticles, 24h (4/40°C, 12h/12h) drying under 11% relative humidity could give rise to a crystallinity up to 50.05%. The applied drying procedures had no obvious effect on the appearance of the amylose nanoparticles. The Z average-size (d. nm) and polydispersity index (PDI) obtained from dynamic light scattering analysis suggested that the drying processes caused some aggregates, but the dried amylose nanoparticles could be well dispersed in water. Copyright © 2017 Elsevier B.V. All rights reserved.

  2. Extreme summer temperatures in Iberia: health impacts and associated synoptic conditions

    Directory of Open Access Journals (Sweden)

    R. García-Herrera

    2005-02-01

    Full Text Available This paper examines the effect of extreme summer temperatures on daily mortality in two large cities of Iberia: Lisbon (Portugal and Madrid (Spain. Daily mortality and meteorological variables are analysed using the same methodology based on Box-Jenkins models. Results reveal that in both cases there is a triggering effect on mortality when maximum daily temperature exceeds a given threshold (34°C in Lisbon and 36°C in Madrid. The impact of most intense heat events is very similar for both cities, with significant mortality values occurring up to 3 days after the temperature threshold has been surpassed. This impact is measured as the percentual increase of mortality associated to a 1°C increase above the threshold temperature. In this respect, Lisbon shows a higher impact, 31%, as compared with Madrid at 21%. The difference can be attributed to demographic and socio-economic factors. Furthermore, the longer life span of Iberian women is critical to explain why, in both cities, females are more susceptible than males to heat effects, with an almost double mortality impact value.

    The analysis of Sea Level Pressure (SLP, 500hPa geopotential height and temperature fields reveals that, despite being relatively close to each other, Lisbon and Madrid have relatively different synoptic circulation anomalies associated with their respective extreme summer temperature days. The SLP field reveals higher anomalies for Lisbon, but extending over a smaller area. Extreme values in Madrid seem to require a more western location of the Azores High, embracing a greater area over Europe, even if it is not as deep as for Lisbon. The origin of the hot and dry air masses that usually lead to extreme heat days in both cities is located in Northern Africa. However, while Madrid maxima require wind blowing directly from the south, transporting heat from Southern Spain and Northern Africa, Lisbon maxima occur under more easterly

  3. Microbial ecology of extreme environments: Antarctic dry valley yeasts and growth in substrate limited habitats

    Science.gov (United States)

    Vishniac, H. S.

    1981-01-01

    The multiple stresses temperature, moisture, and for chemoheterotrophs, sources of carbon and energy of the Dry Valley Antarctica soils allow at best depauperate communities, low in species diversity and population density. The nature of community structure, the operation of biogeochemical cycles, the evolution and mechanisms of adaptation to this habitat are of interest in informing speculations upon life on other planets as well as in modeling the limits of gene life. Yeasts of the Cryptococcus vishniacil complex (Basidiobiastomycetes) are investigated, as the only known indigenes of the most hostile, lichen free, parts of the Dry Valleys. Methods were developed for isolating these yeasts (methods which do not exclude the recovery of other microbiota). The definition of the complex was refined and the importance of nitrogen sources was established as well as substrate competition in fitness to the Dry Valley habitats.

  4. Effect of storage conditions on compaction behavior of two grades of spray-dried lactose.

    Science.gov (United States)

    Atassi, Faraj; Almaya, Ahmad; Aburub, Aktham

    2008-01-01

    In this work we examine the effect of storage conditions (moisture exposure) on the compression behavior of 2 grades of spray-dried lactose (Pharmatose DCL 11 and Pharmatose DCL 14) under 2 different circumstances. The first was to expose powder samples to moisture, then compress them. The second was to expose precompressed tablets to moisture. We clearly show that the effect of moisture exposure and amorphous content crystallization in spray-dried lactoses on compaction behavior depends on whether this moisture exposure takes place before or after compression. In addition, the impact of storage conditions depends on the grade of spray-dried lactose.

  5. Synoptic conditions leading to extremely high temperatures in Madrid

    Directory of Open Access Journals (Sweden)

    R. García

    Full Text Available Extremely hot days (EHD in Madrid have been analysed to determine the synoptic patterns that produce EHDs during the period of 1955–1998. An EHD is defined as a day with maximum temperature higher than 36.5°C, a value which is the threshold for the intense effects on mortatility and it coincides with the 95 percentile of the series. Two different situations have been detected as being responsible for an EHD occurrence, one more dynamical, produced by southern fluxes, and another associated with a stagnation situation over Iberia of a longer duration. Both account for 92% of the total number of days, thus providing an efficient classification framework. A circulation index has been derived to characterise and forecast an EHD occurrence. This paper shows that EHD occur in Madrid during short duration events, and no long heat waves, like those recorded in other cities, are present. Additionally, no clear pattern can be detected in the EHD frequency; the occurrence is tied to changes in the summer location of the Azores high.

    Key words. Meteorology and atmospheric dynamics (Climatology; synoptic-scale meteorology; general or miscellaneous

  6. Synoptic conditions leading to extremely high temperatures in Madrid

    Energy Technology Data Exchange (ETDEWEB)

    Garcia, R.; Prieto, L.; Hernandez, E.; Teso, T. del [Dept. Fisica de la Tierra II, Fac. CC. Fisicas, Univ. Camplutense de Madrid (Spain); Diaz, J. [Centro Universitario de Salud Publica, Univ. Autonoma de Madrid (Spain)

    2002-02-01

    Extremely hot days (EHD) in Madrid have been analysed to determine the synoptic patterns that produce EHDs during the period of 1955-1998. An EHD is defined as a day with maximum temperature higher than 36.5 C, a value which is the threshold for the intense effects on mortatility and it coincides with the 95 percentile of the series. Two different situations have been detected as being responsible for an EHD occurrence, one more dynamical, produced by southern fluxes, and another associated with a stagnation situation over Iberia of a longer duration. Both account for 92% of the total number of days, thus providing an efficient classification framework. A circulation index has been derived to characterise and forecast an EHD occurrence. This paper shows that EHD occur in Madrid during short duration events, and no long heat waves, like those recorded in other cities, are present. Additionally, no clear pattern can be detected in the EHD frequency; the occurrence is tied to changes in the summer location of the Azores high. (orig.)

  7. A Floating Offshore Wind Turbine in Extreme Wave Conditions

    DEFF Research Database (Denmark)

    Wehmeyer, Christof

    and peak enhancement factors, based on cyclonic storm conditions (Wehmeyer et al., 2012). 2. Based on Wehmeyer et al. (2012), a physical model test campaign was drafted, where an industry inspired floating offshore wind turbine was tested (Wehmeyer et al., 2013). 3. A comparison of measured pitch responses...

  8. Performance of Chlorella sorokiniana under simulated extreme winter conditions

    NARCIS (Netherlands)

    Cuaresma, M.; Buffing, M.F.; Janssen, M.G.J.; Lobato, C.V.; Wijffels, R.H.

    2012-01-01

    High annual microalgae productivities can only be achieved if solar light is efficiently used through the different seasons. During winter the productivity is low because of the light and temperature conditions. The productivity and photosynthetic efficiency of Chlorella sorokiniana were assessed

  9. Behavior of whey protein concentrates under extreme storage conditions

    Science.gov (United States)

    The overseas demand for whey protein concentrates (WPC) has increased steadily in recent years. Emergency aid foods often include WPC, but shelf-life studies of whey proteins under different shipment and storage conditions have not been conducted in the last 50 yr. Microbial quality, compound form...

  10. Resilience under conditions of extreme stress: a multilevel perspective.

    Science.gov (United States)

    Cicchetti, Dante

    2010-10-01

    Resilience has been conceptualized as a dynamic developmental process encompassing the attainment of positive adaptation within the context of significant threat, severe adversity, or trauma. Until the past decade, the empirical study of resilience predominantly focused on behavioral and psychosocial correlates of, and contributors to, the phenomenon and did not examine neurobiological or genetic correlates of and contributors to resilience. Technological advances in molecular genetics and neuroimaging, and in measuring other biological aspects of behavior, have made it more feasible to begin to conduct research on pathways to resilient functioning from a multilevel perspective. Child maltreatment constitutes a profound immersion in severe stress that challenges and frequently impairs development across diverse domains of biological and psychological functioning. Research on the determinants of resilience in maltreated children is presented as an illustration of empirical work that is moving from single-level to multilevel investigations of competent functioning in the face of adversity and trauma. These include studies of personality, neural, neuroendocrine, and molecular genetic contributors to resilient adaptation. Analogous to neural plasticity that takes place in response to brain injury, it is conjectured that it may be possible to conceptualize resilience as the ability of individuals to recover functioning after exposure to extreme stress. Multilevel randomized control prevention and intervention trials have substantial potential for facilitating the promotion of resilient functioning in diverse high-risk populations that have experienced significant adversity. Determining the multiple levels at which change is engendered through randomized control trials will provide insight into the mechanisms of change, the extent to which neural plasticity may be promoted, and the interrelations between biological and psychological processes in the development of

  11. The effect of field condition and shoe type on lower extremity injuries in American Football.

    Science.gov (United States)

    Iacovelli, Jaclyn Nicole; Yang, Jingzhen; Thomas, Geb; Wu, Hongqian; Schiltz, Trisha; Foster, Danny T

    2013-08-01

    Considerable improvement has been made in football field surfaces and types of shoe, yet relatively few epidemiological studies have investigated their roles in the risk of football injuries. This study examined the effects of field surface, surface condition and shoe type on the likelihood of lower extremity football injuries. Deidentified data from 188 players from one division I university football team during the 2007-2010 seasons were analysed. Lower extremity injury rate and rate ratio, along with 95% confidence limits, were calculated by football activity, playing surface condition and shoe type. A total of 130 lower extremity injuries were sustained, with an overall lower extremity injury rate of 33.5/10 000 athlete-sessions. The lower extremity injury rate was 2.61 times higher when the surface condition was abnormal compared with when the surface condition was normal. During games, the risk for lower extremity injury was 3.34 times higher (95% CI 1.70 to 6.56) on artificial turf compared with natural grass. However, this trend was not statistically significant in practice sessions. Furthermore, neither the number of shoe cleats nor the height of the shoe top was statistically associated with risk of lower extremity injuries. Football players who played on artificial turf or when the surface condition was abnormal were susceptible to lower extremity injuries. Evidence from this study suggests that further research into playing surfaces and shoe types may provide fruitful opportunities to reduce injuries to collegiate football players.

  12. Mathematical modelling of unglazed solar collectors under extreme operating conditions

    DEFF Research Database (Denmark)

    Bunea, M.; Perers, Bengt; Eicher, S.

    2015-01-01

    average temperature levels at the evaporator. Simulation of these systems requires a collector model that can take into account operation at very low temperatures (below freezing) and under various weather conditions, particularly operation without solar irradiation.A solar collector mathematical model......Combined heat pumps and solar collectors got a renewed interest on the heating system market worldwide. Connected to the heat pump evaporator, unglazed solar collectors can considerably increase their efficiency, but they also raise the coefficient of performance of the heat pump with higher...... was found due to the condensation phenomenon and up to 40% due to frost under no solar irradiation. This work also points out the influence of the operating conditions on the collector's characteristics.Based on experiments carried out at a test facility, every heat flux on the absorber was separately...

  13. Investigating the Effects of Simulated Space conditions on Novel Extremely Halophilic Archaea: Halovarius Luteus gen. nov., sp. nov.

    Science.gov (United States)

    Feshangsaz, Niloofar; Van Loon, ing.. Jack J. W. A.; Nazmi, Kamran; Semsarha, Farid

    2016-07-01

    Studying halophiles from different environments of Earth provide new insights into our search for life in the universe. Haloarchaea show some unique characteristics and physiological adaptations like acidic proteins against harsh environments such as natural brine with salt concentration approaching saturation (5 M) and regions with low active water. These properties make haloarchaea interesting candidate for astrobiological studies. Halovarius luteus gen. nov., sp. nov. a novel extremely halophilic archaeon from Urmia salt lake, in Iran has been chosen to explore its resistance against a series of extreme conditions. The aim of this study is to assess the resistance of strain DA50T under the effects of simulated space conditions like simulated microgravity, hypergravity, and desiccation. In this paper we will discuss the results of these studies where we specifically focus on changes in carotenoid pigments production and whole cell proteome. This is the first report of very novel Iranian archaea in response to extreme space conditions. The pigments were extracted by acetone and methanol. Pigments were analyzed by scanning the absorbance spectrum in the UV-VIS spectrophotometer. And they were separated by TLC. Whole protein from cell lysate supernatant was extracted after lysis with Bacterial Protein Extraction Reagent and fractionated by RP-HPLC using C18 column. Proteome analyzed by electrophoresis (SDS-PAGE), and MALDI-TOF. Carotenoid pigments are formed under different extreme conditions such as dry environment and gravitational changes. Also the protein composition exhibits alterations after exposure to the same conditions. Our conclusion is that pigments and proteins formation depend on the growth circumstances. Halophiles use this as an adaptation to survive under different environmental conditions.

  14. EXTREME METEOROLOGICAL CONDITIONS AND METABOLIC PROFILE IN HIGH YIELDING HOLSTEINFRIESIAN DAIRY COWS

    Directory of Open Access Journals (Sweden)

    Z. GERGÁCZ

    2013-12-01

    Full Text Available The impact of two years (2002 and 2003 with different summer temperature extremes on variation in metabolic profile was analyzed in blood and urine samples taken from healthy, primiparous (n = 371 and multiparous (n = 795 high yielding Holstein-Friesian dairy cows. In this study main focus was lead on three most critical physiological phases, thus cows were assigned into three groups as follows: (1 dry cows for 10 days prior to calving; (2 cows 1-30 days after delivery, and (3 cows with more than 31 days post partum. Findings reveal clear response of the cows to heat in selected blood (hemoglobin, plasma aceto-acetic-acid, FFA, AST, glucose, urea and urine (pH, NABE and urea parameters. In the majority of cows, glucose and hemoglobin level, one of the most significant blood parameters, indicated symptoms of insufficient energy supply. Further metabolic indicators differed more or less from reference values depending on actual condition. Due to heat load dry matter intake has been decreased even by 10-15 per cent in primiparous cows. They were expected to increase body weight and size and simultaneously produce attain at large milk yields. In doing so that cows would have require large amount of nutrients. Out of parameters such as hemoglobin, glucose, FFA, AST and blood-urea differed from the reference values in most cases; however, this phenomenon seemed to be present in almost every case for hemoglobin and glucose. The lack of energy caused by heat stress can be contributed to the decrease of dry matter intake which has been indicated by the urea levels and pH both in blood and urine prevailing unfavorable and insufficient feeding practice. The results reconfirm the need to reconsider both the actual feeding practice (e.g. to increase of nutrient content in rations, reduce the intake of soluble proteins in rumen, pay attention of crude fiber in Total Mixed Rations (TMR, NDF and ADF, avoid overfeeding of inorganic buffers, to control moisture

  15. Inference for Extremal Conditional Quantile Models, with an Application to Market and Birthweight Risks

    CERN Document Server

    Chernozhukov, Victor

    2009-01-01

    Quantile regression is an increasingly important empirical tool in economics and other sciences for analyzing the impact of a set of regressors on the conditional distribution of an outcome. Extremal quantile regression, or quantile regression applied to the tails, is of interest in many economic and financial applications, such as conditional value-at-risk, production efficiency, and adjustment bands in (S,s) models. In this paper we provide feasible inference tools for extremal conditional quantile models that rely upon extreme value approximations to the distribution of self-normalized quantile regression statistics. The methods are simple to implement and can be of independent interest even in the non-regression case. We illustrate the results with two empirical examples analyzing extreme fluctuations of a stock return and extremely low percentiles of live infants' birthweights in the range between 250 and 1500 grams.

  16. Water-CO2 Mixtures Under Extreme Conditions

    Science.gov (United States)

    Plattner, D. L.; Somayazulu, M.

    2010-12-01

    In situ high pressure-temperature Raman spectroscopy was used to investigate the formation of clathrates in water-CO2 mixtures and to study the chemical interactions between water and CO2 at supercritical conditions. Diamond anvil cell’s (DAC) were loaded with ruby, water, CO2, and a gold plated gasket. Quartz was later added to the cell as a pressure sensor for supercritical phase analysis. At 25 °C and within the pressure range of 0.8 to 2.6 GPa, no clathrate was observed. Our results confirm recent findings which also dispute claims of clathrate existence at our conditions. A decrease in the temperature required to reach the supercritical phase of water-CO2 mixtures was observed from 0.35 GPa to 4.5 GPa. Furthermore, at 4.4 GPa and 290 °C, a chemical reaction between CO2 and water occurred. The resulting compound has a Raman peak with a frequency shift of 1000 cm-1. This reaction and the compound it produces are of great interest and are currently being investigated.

  17. The microbial sulfur cycle at extremely haloalkaline conditions of soda lakes

    NARCIS (Netherlands)

    Sorokin, D.Y.; Kuenen, J.G.; Muyzer, G.

    2011-01-01

    Soda lakes represent a unique ecosystem with extremely high pH (up to 11) and salinity (up to saturation) due to the presence of high concentrations of sodium carbonate in brines. Despite these double extreme conditions, most of the lakes are highly productive and contain a fully functional

  18. Matter under Extreme Conditions: Advances Based on Static Compression

    Science.gov (United States)

    Hemley, Russell

    2008-04-01

    Current technological advances make it possible to perform experiments on materials at static or sustained conditions to multimegabar pressures (several hundred GPa) and several thousand degree (˜1 eV) temperatures. Densities of condensed matter can now be increased over an order of magnitude, causing novel transformations and new physical and chemical phenomena to occur. Growth in this area has been made possible by advances in diamond-anvil cell methods coupled with a wide range of probes, including x-ray diffraction, spectroscopy, inelastic scattering, radiography, and infrared spectroscopy using synchrotron radiation. Examples include investigations of dense hydrogen; transformations in molecular materials; novel ceramics; new types of superconductors, electronic, and magnetic materials; and liquids and amorphous materials. Particularly exciting are new developments in time resolved methods and coupling of static and dynamic compression techniques made possible by the creation of new large-scale facilities and novel technologies.

  19. A Floating Offshore Wind Turbine in Extreme Wave Conditions

    DEFF Research Database (Denmark)

    Wehmeyer, Christof

    and peak enhancement factors, based on cyclonic storm conditions (Wehmeyer et al., 2012). 2. Based on Wehmeyer et al. (2012), a physical model test campaign was drafted, where an industry inspired floating offshore wind turbine was tested (Wehmeyer et al., 2013). 3. A comparison of measured pitch responses...... versus responses from an in-house developed numerical tool, as well as a code to code comparison in regular non-linear waves served as initial key performance indicator of numerical model quality and good agreement was found (Wehmeyer et al., 2014). 4. As a final step, the numerical model was extended...... in order to include non-linear irregular incident waves as well as non-linear irregular incident waves with an embedded Stream-function wave. A linear background sea state into which a Stream-function wave was embedded was assumed no longer appropriate. Therefore a 2nd order sea state model was developed...

  20. Influence of emulsion composition and spray-drying conditions on microencapsulation of tilapia oil.

    Science.gov (United States)

    Huang, Hui; Hao, Shuxian; Li, Laihao; Yang, Xianqing; Cen, Jianwei; Lin, Wanling; Wei, Ya

    2014-09-01

    The influence of processing conditions on the microencapsulation of tilapia oil by spray drying was studied. Trehalose, gelatin, sucrose and xanthan were used as emulsion composition. The experimental parameters of spray drying such as inlet air temperature, solid content, drying air flow rate and atomizing pressure were optimized using a central composite design. Encapsulation efficiency and lipid oxidation were determined. Bulk density, powder morphology and particle size were also analyzed. Trehalose improved the glass transition temperature of wall material significantly and prevented the oxidation of the fish oil. Encapsulation efficiency reached a maximum of 90 % under optimum conditions with an inlet air temperature of 121 °C, a drying air flow rate of 0.65 m(3)/min and a spray pressure of 100 kPa.

  1. Complaints of Upper Extremity Numbness and Tingling Relieved With Dry Needling of the Teres Minor and Infraspinatus: A Case Report.

    Science.gov (United States)

    Lane, Elizabeth; Clewley, Derek; Koppenhaver, Shane

    2017-04-01

    Study Design Case report. Background Abnormal sensation, such as numbness or tingling, is traditionally thought to originate from neural compression. There is limited evidence to support reports of abnormal sensation arising from a trigger point. Case Description The patient was a 60-year-old woman with a primary complaint of right shoulder pain and secondary complaints of neck pain and right upper extremity numbness. Cervical spine neurological examination was unremarkable, and manual examination did not reproduce the patient's arm numbness or tingling symptoms. Compression of a trigger point in the infraspinatus and teres minor reproduced the patient's primary complaint of shoulder pain. The initial intervention included dry needling, which reproduced her upper extremity numbness. Subsequent treatment included manual therapy and exercise. Outcomes The patient was seen for a total of 3 visits, including the evaluation. Dry needling was utilized in 2 of her 3 visits. At discharge, she reported complete resolution of pain and altered sensation. Additionally, her scores on the Neck Disability Index, numeric pain-rating scale, and global rating of change exceeded the minimal clinically important difference. These outcomes were maintained at 2- and 12-month follow-up phone calls. Discussion This case report described the examination and use of dry needling in a case where the diagnosis was unclear. Clinicians may consider trigger point referral when examining patients with reports of abnormal sensation, especially when a more common cause cannot be identified. Level of Evidence Therapy, level 5. J Orthop Sports Phys Ther 2017;47(4):287-292. Epub 3 Mar 2017. doi:10.2519/jospt.2017.7055.

  2. Drying Shrinkage of Cement-Based Materials Under Conditions of Constant Temperature and Varying Humidity

    Institute of Scientific and Technical Information of China (English)

    MA Bao-guo; WEN Xiao-dong; WANG Ming-yuan; YAN Jia-jia; Gao Xiao-jian

    2007-01-01

    Currently,deformations along the central axis of specimens were usually measured under fixed environmental conditions. Seldom were the effects of environmental factors on the drying-shrinkage deformation of cement-based material considered. For this paper, the drying-shrinkage deformation at different w/b ratios and different additions to mortars was investigated under different environments at a temperature of 20 ℃ and humidity ranging from 100% to 50%. The specimens were cured in water for 28 days before measurement. The results illustrate that mortar shows much less shrinkage under various drying conditions when a lower w/b ratio is adopted. With a decrease in relative humidity the speed of drying-shrinkage becomes gradually lower. The addition of silica fume reduces the drying-shrinkage of mortar under higher relative humidity, because the pore structure of mortar with silica fume becomes more refined. The addition of fly ash increases the total porosity and the volume of coarse pores in the mortar. The drying-shrinkage of mortar under different conditions increases with the addition of more of fly ash.

  3. Influence of intermittent wetting and drying conditions on heavy metal removal by stormwater biofilters.

    Science.gov (United States)

    Blecken, Godecke-Tobias; Zinger, Yaron; Deletić, Ana; Fletcher, Tim D; Viklander, Maria

    2009-10-01

    Biofiltration is a technology to treat urban stormwater runoff, which conveys pollutants, including heavy metals. However, the variability of metals removal performance in biofiltration systems is as yet unknown. A laboratory study has been conducted with vegetated biofilter mesocosms, partly fitted with a submerged zone at the bottom of the filter combined with a carbon source. The biofilters were dosed with stormwater according to three different dry/wet schemes, to investigate the effect of intermittent wetting and drying conditions on metal removal. Provided that the biofilters received regular stormwater input, metal removal exceeded 95%. The highest metal accumulation occurs in the top layer of the filter media. However, after antecedent drying before a storm event exceeding 3-4 weeks the filters performed significantly worse, although metal removal still remained relatively high. Introducing a submerged zone into the filter improved the performance significantly after extended dry periods. In particular, copper removal in filters equipped with a submerged zone was increased by around 12% (alpha=0.05) both during wet and dry periods and for lead the negative effect of drying could completely be eliminated, with consistently low outflow concentrations even after long drying periods.

  4. Dry pretreatment of lignocellulose with extremely low steam and water usage for bioethanol production.

    Science.gov (United States)

    Zhang, Jian; Wang, Xiusheng; Chu, Deqiang; He, Yanqing; Bao, Jie

    2011-03-01

    Two rarely noticed but important parameters of the dilute sulfuric acid pretreatment of lignocellulose biomass, the feedstock filling ratio to the pretreatment reactor and the solids/liquid presoaking ratio, were extensively studied. The effects of the two parameters on the steam consumption, waste water generation, and pretreatment efficiency were investigated. At the full filling ratio and high solids/liquid presoaking ratio, this "dry" pretreatment method provided at least the following advantages: (1) the steam consumption was significantly reduced; (2) no aqueous acid containing waste water was generated; (3) high solids content of the pretreated materials were obtained and the consequent saccharification and fermentation was carried out at high solids loading easily. This method was applied to various lignocellulose feedstocks successfully and provided a practical means to produce ethanol economically feasible. Copyright © 2011 Elsevier Ltd. All rights reserved.

  5. Extreme dry spell detection and climatology over the Mediterranean Basin during the wet season

    Science.gov (United States)

    Raymond, Florian; Ullmann, Albin; Camberlin, Pierre; Drobinski, Philippe; Smith, Carmela Chateau

    2016-07-01

    The E-OBS precipitation gridded data set v.10.0 is used to detect very long dry spell (VLDS) events over the entire Mediterranean Basin for the 1957-2013 period, during the wet season (September to April). The main objective is to characterize these events as climatic objects, in terms of location, spatial extent, duration, and temporal variability. In this study, 76 VLDS events were detected in the Mediterranean Basin and grouped into four spatial patterns: scattered localized (with 25 events), northeast Mediterranean (11 events), West Mediterranean (15 events), and southeast Mediterranean (25 events). Each pattern shows seasonality in events. Most of the scattered localized, northeast, and southeast events begin in September, at the beginning of the wet season. In contrast, most of the West Mediterranean events begin in the middle of the wet season. Over time, there is a slight but not significant increase in the cumulative number of days per season affected by VLDS events.

  6. Microbial ecology of extreme environments: Antarctic dry valley yeasts and growth in substrate-limited habitats

    Science.gov (United States)

    Vishniac, H. S.

    1982-01-01

    The success of the Antarctic Dry Valley yeasts presumeably results from adaptations to multiple stresses, to low temperatures and substrate-limitation as well as prolonged resting periods enforced by low water availability. Previous investigations have suggested that the crucial stress is substrate limitation. Specific adaptations may be pinpointed by comparing the physiology of the Cryptococcus vishniacii complex, the yeasts of the Tyrol Valley, with their congeners from other habitats. Progress was made in methods of isolation and definition of ecological niches, in the design of experiments in competition for limited substrate, and in establishing the relationships of the Cryptococcus vishniacii complex with other yeasts. In the course of investigating relationships, a new method for 25SrRNA homology was developed. For the first time it appears that 25SrRNA homology may reflect parallel or convergent evolution.

  7. Diagnosing the Nature of Land-Atmosphere Coupling During the 2006-7 Dry/Wet Extremes in the U. S. Southern Great Plains

    Science.gov (United States)

    Santanello, Joseph A.; Peters-Lidard, Christa D.; Kennedy, Aaron D.; Kumar, Sujay; Dong, Xiquan

    2011-01-01

    Land-atmosphere (L-A) interactions play a critical role in determining the diurnal evolution of land surface and planetary boundary layer (PBL) temperature and moisture states and fluxes. In turn, these interactions regulate the strength of the connection between surface moisture and precipitation in a coupled system. To address deficiencies in numerical weather prediction and climate models due to improper treatment of L-A interactions, recent studies have focused on development of diagnostics to quantify the strength and accuracy of the land-PBL coupling at the process-level. In this study, a diagnosis of the nature and impacts of local land-atmosphere coupling (LoCo) during dry and wet extreme conditions is presented using a combination of models and observations during the summers of2006-7 in the U.S. Southern Great Plains. Specifically, the Weather Research and Forecasting (WRF) model has been coupled to NASA's Land Information System (LIS), which provides a flexible and high resolution representation and initialization of land surface physics and states. A range of diagnostics exploring the links and feedbacks between soil moisture and precipitation are examined for the dry/wet regimes of this region, along with the behavior and accuracy of different land-PBL scheme couplings under these conditions. Results demonstrate how LoCo diagnostics can be applied to coupled model components in the context of their integrated impacts on the process-chain connecting the land surface to the PBL and support of hydrological anomalies.

  8. New model for colour kinetics of plum under infrared vacuum condition and microwave drying

    Directory of Open Access Journals (Sweden)

    Reza Amiri Chayjan

    2016-06-01

    Full Text Available Background. Quality of dried foods is affected by the drying method and physiochemical changes in tissue. The drying method affects properties such as colour. The colour of processed food is one of the most impor- tant quality indices and plays a determinant role in consumer acceptability of food materials and the process- ing method. The colour of food materials can be used as an indirect factor to determine changes in quality, since it is simpler and faster than chemical methods. Material and methods. The study focused on the kinetics of colour changes of plum slices, under infrared vacuum and microwave conditions. Drying the samples was implemented at the absolute pressures of 20 and 60 kPa, drying temperatures of 50 and 60°C and microwave power of 90, 270, 450 and 630 W. Colour changes were quantified by the tri-stimulus L* (whiteness/darkness, a* (redness/greenness and b* (yellow- ness/blueness model, which is an international standard for color measurement developed by the Commis- sion Internationale d’Eclairage (CIE. These values were also used to calculate total colour change (∆E, chroma, hue angle, and browning index (BI. A new model was used for mathematical modelling of colour change kinetics. Results. The drying process changed the colour parameters of L*, a*, and b*, causing a colour shift toward the darker region. The values of L* and hue angle decreased, whereas the values of a*, b*, ∆E, chroma and browning index increased during exposure to infrared vacuum conditions and microwave drying. Comparing the results obtained using the new model with two conventional models of zero-order and first-order kinet- ics indicated that the new model presented more compatibility with the data of colour kinetics for all colour parameters and drying conditions. Conclusion. All kinetic changes in colour parameters can be explained by the new model presented in this study. The hybrid drying system included infrared vacuum conditions and

  9. High shear treatment of concentrates and drying conditions influence the solubility of milk protein concentrate powders.

    Science.gov (United States)

    Augustin, Mary Ann; Sanguansri, Peerasak; Williams, Roderick; Andrews, Helen

    2012-11-01

    The solubility of milk protein concentrate (MPC) powders was influenced by the method used for preparing the concentrate, drying conditions, and the type of dryer used. Increasing total solids of the ultrafiltered concentrates (23% total solids, TS) by diafiltration to 25% TS or evaporation to 31% TS decreased the solubility of MPC powders (80-83% protein, w/w dry basis), with ultrafiltration followed by evaporation to higher total solids having the greater detrimental effect on solubility. High shear treatment (homogenisation at 350/100 bar, microfluidisation at 800 bar or ultrasonication at 24 kHz, 600 watts) of ultrafiltered and diafiltered milk protein concentrates prior to spray drying increased the nitrogen solubility of MPC powders (82% protein, w/w dry basis). Of the treatments applied, microfluidisation was the most effective for increasing nitrogen solubility of MPC powders after manufacture and during storage. Manufacture of MPC powders (91% protein, w/w dry basis) prepared on two different pilot-scale dryers (single stage or two stage) from milk protein concentrates (20% TS) resulted in powders with different nitrogen solubility and an altered response to the effects of microfluidisation. Microfluidisation (400, 800 and 1200 bar) of the concentrate prior to drying resulted in increased long term solubility of MPC powders that were prepared on a single stage dryer but not those produced on a two stage spray dryer. This work demonstrates that microfluidisation can be used as a physical intervention for improving MPC powder solubility. Interactions between the method of preparation and treatment of concentrate prior to drying, the drying conditions and dryer type all influence MPC solubility characteristics.

  10. Diagnosing the Nature of Land-Atmosphere Coupling: A Case Study of Dry/Wet Extremes in the U. S. Southern Great Plains

    Science.gov (United States)

    Santanello, Joseph A. Jr.; Peters-Lidard, Christa D.; Kennedy, Aaron; Kumar, Sujay V.

    2012-01-01

    Land-atmosphere (L-A) interactions play a critical role in determining the diurnal evolution of land surface and planetary boundary layer (PBL) temperature and moisture states and fluxes. In turn, these interactions regulate the strength of the connection between surface moisture and precipitation in a coupled system. To address model deficiencies, recent studies have focused on development of diagnostics to quantify the strength and accuracy of the land- PBL coupling at the process-level. In this paper, a diagnosis of the nature and impacts of local land-atmosphere coupling (LoCo) during dry and wet extreme conditions is presented using a combination of models and observations during the summers of 2006 and 2007 in the U.S. Southern Great Plains. A range of diagnostics exploring the links and feedbacks between soil moisture and precipitation are applied to the dry/wet regimes exhibited in this region, and in the process a thorough evaluation of nine different land-PBL scheme couplings is conducted under the umbrella of a high-resolution regional modeling testbed. Results show that the sign and magnitude of errors in land surface energy balance components are sensitive to the choice of land surface model, regime type, and running mode. In addition, LoCo diagnostics show that the sensitivity of L-A coupling is stronger towards the land during dry conditions, while the PBL scheme coupling becomes more important during the wet regime. Results also demonstrate how LoCo diagnostics can be applied to any modeling system (e.g. reanalysis products) in the context of their integrated impacts on the process-chain connecting the land surface to the PBL and in support of hydrological anomalies.

  11. Critical review of creep FRAPCON-3 model under dry storage conditions

    Energy Technology Data Exchange (ETDEWEB)

    Feria, F.; Herranz, L.E. [Unit of Nuclear Safety Research, CIEMAT, Avda. Complutense 22, Madrid, Madrid 28040 (Spain)

    2009-06-15

    There is a general agreement that cladding creep rupture is the most likely and limiting failure mechanism of spent fuel in dry storage compared to other potential mechanisms, like stress corrosion cracking and/or delayed hydride cracking. Nevertheless, occurrence of creep rupture is very improbable since both decay heat and hoop stress tend to decrease throughout dry storage. In spite of this, the current trend to higher burn up levels needs further attention that ensures safe storage of spent fuel irradiated over 45 GWd/MTU. An extensive work has been carried out during the last four decades in the area of in-reactor creep modelling. Unfortunately, the in-reactor conditions are so different from those prevailing under dry storage, that all the experience gained cannot be extrapolated in a straightforward manner. On the other side, as creep tests simulating conditions throughout a 20-40 year dry storage are impractical, post-irradiation cladding creep behaviour has been modelled by means of time-temperature dependent laws developed on the basis of currently available zirconium alloys data. Additionally, some tests have been exploring the effect of irradiation, hydrogen distribution and material composition on the materials creep behaviour. Adaptation of fuel performance codes initially developed for normal and off-normal reactor operation is not an easy task either. Creep modelling is usually dependent of host codes because a good part of its validation and update has been carried out in an integral way, and as a consequence its independent performance assessment is not an easy task. This work examines the current capability of FRAPCON-3 to model creep behaviour under dry storage conditions. To do so, a review of its major fundamentals has been done and its range of applicability discussed. Once its main approximations and drawbacks have been identified, an attempt to overcome some of them has been intended by implementing an alternative expression for creep under

  12. Drying characteristics of zucchini slices under periodic infrared-microwave vacuum conditions

    Science.gov (United States)

    Chayjan, Reza Amiri; Dibagar, Nesa; Alaei, Behnam

    2017-06-01

    The purpose of the presented study was to describe the effects of various drying conditions on the drying behavior of zucchini slices as well as specifications of diffusivity, activation energy, shrinkage, and color. Zucchini samples, as the richest fount of macronutrient and micronutrient, were subjected to periodic microwave vacuum drying (at 450 W) at three levels of temperature (40, 50 and 60 °C), absolute pressure (20, 40 and 60 kPa) and exposure time (20-3, 30-4.5 and 40-6 s-min). An increase in the drying temperature and exposure time along with a decrease in absolute pressure caused a reduction in total drying time, however, greater heat damages and adversely texture and color effects were observed in this case. The effective moisture diffusivity of zucchini varied between 5.41×10-10 and 1.75×10-9, indicating that under circumstances of high temperature, long exposure time and low absolute pressure water was able to rapidly diffuse out of the tissue in the experimental domain. Lowering the absolute pressure of vacuum flask and increasing the exposure time led to the reduction in the activation energy of samples. The shrinkage coefficient was within the range of 79.91 to 84.92%. As such, the greatest total color difference was calculated between the color of raw and dried samples for those experiments with the largest increase in temperature, exposure time and a decrease in absolute pressure.

  13. Effect of pre-drying and par-frying conditions on the crispness of French fries

    NARCIS (Netherlands)

    Loon, W.A.M.; Visser, J.E.; Linssen, J.P.H.; Somsen, D.J.; Klok, H.J.; Voragen, A.G.J.

    2007-01-01

    An experimental design was used to study the effect of pre-drying (to 10, 15 and 20% weight loss) and par-frying conditions (160, 170 and 180 °C) on the crispness of French fries. Par-frying time was adjusted with a software program to obtain equal moisture content and internal texture for all sampl

  14. Optimization of microwave drying conditions of two banana varieties using response surface methodology

    Directory of Open Access Journals (Sweden)

    Adewale Olusegun Omolola

    2015-09-01

    Full Text Available AbstractOptimization of microwave drying conditions of Luvhele and Mabonde banana varieties were studied using response surface methodology. The drying was performed using a central composite rotatable design for two variables: microwave power level (100, 200 and 300 W and drying time (40, 26, and 12 min. for Luvhele; (100, 200 and 300 W and (42, 27, and 12 min for Mabonde. The colour and texture (hardness data were analyzed using ANOVA and regression analysis. The fitness of the models obtained was good as the lack of fit for each of the models was not significant. The coefficient of determination R2 of the models was relatively high, hence the models obtained for the responses were adequate and acceptable. Drying conditions of 178.76 W, 12 min. drying time were found optimum for product quality at a desirability of 0.91 for Luvhele; while 127.67 W, 12 min. with a desirability of 0.86 was predicted for Mabonde. The result of this study could be used as a standard for microwave processing of Luvhele and Mabondebanana varieties.

  15. Functional and physicochemical properties of whole egg powder: effect of spray drying conditions.

    Science.gov (United States)

    Koç, Mehmet; Koç, Banu; Susyal, Gonca; Sakin Yilmazer, Melike; Kaymak Ertekin, Figen; Bağdatlıoğlu, Neriman

    2011-04-01

    Pasteurized liquid whole egg was subjected to spray drying to determine the effect of spray drying conditions on moisture content, water activity, peroxide value, emulsion stability, gel texture, foaming stability and colour change of the powder product. Drying process was carried out in a pilot scale spray dryer (Mobile Minor Niro-Atomizer, Denmark). The inlet (165-195 °C) and outlet air temperatures (60-80 °C) and the atomization pressure (196-392 kPa) were investigated as spray drying process variables. Perturbation and 3-D graphs revealed that outlet air temperature and atomization pressure had more effect than inlet air temperature, on the properties of whole egg powder. Optimum spray drying conditions of whole egg powder were determined according to the specific end-product requirements (bakery foods, omelette and mayonnaise and salad dressing) targeting to obtain the desired value of functional properties, i.e.; emulsion stability, gel texture, foaming stability and colour change.

  16. Unusual salinity conditions in the Yangtze estuary in 2006: impacts of an extreme drought or of the Three Gorges Dam?

    Science.gov (United States)

    Dai, Zhijun; Chu, Ao; Stive, Marcel; Zhang, Xiaoling; Yan, Hong

    2011-07-01

    During the extreme dry year of 2006, abnormal salinity conditions in the Changjiang Estuary of the Yangtze River occurred in partial coincidence with the second impoundment phase of the TGD (Three Gorges Dam). Analysis of discharge observations in the upper reaches of the estuary and of salinity observations in the estuary as a whole reveals that in 2006 salinity was over 100 mg/l during 275 days, over 250 mg/l during 75 days and over 400 mg/l during 48 days. It is well known that this is due to extreme low discharges from the upper catchment area into the estuary. Moreover, large amounts of water consumed along the lower reaches of the Yangtze River can also aggravate the low discharges that lead to stronger saltwater intrusion in the estuary. Of the 75 days that salinity was over 250 mg/l, the low discharge was decreased further by 10 to 20% due to water consumption. The additional impact of the impoundment phase of the TGD (lasting 37 days in autumn) was noticeable only during 7 days in 2006. During that period, the relative contributions of the TGD and the water consumption in the lower reaches of the Yangtze River amounted to 70 and 30%, respectively. It may be concluded that the impact of the second impoundment phase of the TGD on salinity intrusion in the estuary was modest, while the extreme drought of 2006 was the dominant cause.

  17. Resistance of Microorganisms to Extreme Environmental Conditions and Its Contribution to Astrobiology

    Directory of Open Access Journals (Sweden)

    Pabulo Henrique Rampelotto

    2010-06-01

    Full Text Available In the last decades, substantial changes have occurred regarding what scientists consider the limits of habitable environmental conditions. For every extreme environmental condition investigated, a variety of microorganisms have shown that not only can they tolerate these conditions, but that they also often require these extreme conditions for survival. Microbes can return to life even after hundreds of millions of years. Furthermore, a variety of studies demonstrate that microorganisms can survive under extreme conditions, such as ultracentrifugation, hypervelocity, shock pressure, high temperature variations, vacuums, and different ultraviolet and ionizing radiation intensities, which simulate the conditions that microbes could experience during the ejection from one planet, the journey through space, as well as the impact in another planet. With these discoveries, our knowledge about the biosphere has grown and the putative boundaries of life have expanded. The present work examines the recent discoveries and the principal advances concerning the resistance of microorganisms to extreme environmental conditions, and analyzes its contributions to the development of the main themes of astrobiology: the origins of life, the search for extraterrestrial life, and the dispersion of life in the Universe.

  18. The Effect of Operating Conditions on Drying Characteristics and Quality of Ginger (Zingiber Officinale Roscoe) Using Combination of Solar Energy-Molecular Sieve Drying System

    Science.gov (United States)

    Hasibuan, R.; Zamzami, M. A.

    2017-03-01

    Ginger (Zingiber officinale Roscoe) is an agricultural product that can be used as beverages and snacks, and especially for traditional medicines. One of the important stages in the processing of ginger is drying. The drying process intended to reduce the water content of 85-90% to 8-10%, making it safe from the influence of fungi or insecticide. During the drying takes place, the main ingredient contained in ginger is homologous ketone phenolic known as gingerol are chemically unstable at high temperatures, for the drying technology is an important factor in maintaining the active ingredient (gingerol) which is in ginger. The combination of solar energy and molecular sieve dryer that are used in the research is capable of operating 24 hours. The purpose of this research is to study the effect of operating conditions (in this case the air velocity) toward the drying characteristics and the quality of dried ginger using the combination of solar energy and molecular sieve dryer. Drying system consist of three main parts which is: desiccator, solar collector, and the drying chamber. To record data changes in the mass of the sample, a load cell mounted in the drying chamber, and then connected to the automated data recording system using a USB data cable. All data of temperature and RH inside the dryer box and the change of samples mass recorded during the drying process takes place and the result is stored in the form of Microsoft Excel. The results obtained, shows that the air velocity is influencing the moisture content and ginger drying rate, where the moisture content equilibrium of ginger for the air velocity of 1.3 m/s was obtained on drying time of 360 minutes and moisture content of 2.8%, at 1.0 m/s was obtained on drying time of 300 minutes and moisture content of 1.4%, at 0, 8 m/s was obtained at 420 minutes drying time and the moisture content is 2.0%. The drying characteristics shows that there are two drying periods, which is: the increasing drying rate

  19. Drilling force and temperature of bone under dry and physiological drilling conditions

    Science.gov (United States)

    Xu, Linlin; Wang, Chengyong; Jiang, Min; He, Huiyu; Song, Yuexian; Chen, Hanyuan; Shen, Jingnan; Zhang, Jiayong

    2014-11-01

    Many researches on drilling force and temperature have been done with the aim to reduce the labour intensiveness of surgery, avoid unnecessary damage and improve drilling quality. However, there has not been a systematic study of mid- and high-speed drilling under dry and physiological conditions(injection of saline). Furthermore, there is no consensus on optimal drilling parameters. To study these parameters under dry and physiological drilling conditions, pig humerus bones are drilled with medical twist drills operated using a wide range of drilling speeds and feed rates. Drilling force and temperature are measured using a YDZ-II01W dynamometer and a NEC TVS-500EX thermal infrared imager, respectively, to evaluate internal bone damage. To evaluate drilling quality, bone debris and hole morphology are observed by SEM(scanning electron microscopy). Changes in drilling force and temperature give similar results during drilling such that the value of each parameter peaks just before the drill penetrates through the osteon of the compact bone into the trabeculae of the spongy bone. Drilling temperatures under physiological conditions are much lower than those observed under dry conditions, while a larger drilling force occurs under physiological conditions than dry conditions. Drilling speed and feed rate have a significant influence on drilling force, temperature, bone debris and hole morphology. The investigation of the effect of drilling force and temperature on internal bone damage reveals that a drilling speed of 4500 r/min and a feed rate of 50 mm/min are recommended for bone drilling under physiological conditions. Drilling quality peaks under these optimal parameter conditions. This paper proposes the optimal drilling parameters under mid- and high-speed surgical drilling, considering internal bone damage and drilling quality, which can be looked as a reference for surgeons performing orthopedic operations.

  20. Drilling Force and Temperature of Bone under Dry and Physiological Drilling Conditions

    Institute of Scientific and Technical Information of China (English)

    XU Linlin; WANG Chengyong; JIANG Min; HE Huiyu; SONG Yuexian; CHEN Hanyuan; SHEN Jingnan; ZHANG Jiayong

    2014-01-01

    Many researches on drilling force and temperature have been done with the aim to reduce the labour intensiveness of surgery, avoid unnecessary damage and improve drilling quality. However, there has not been a systematic study of mid- and high-speed drilling under dry and physiological conditions(injection of saline). Furthermore, there is no consensus on optimal drilling parameters. To study these parameters under dry and physiological drilling conditions, pig humerus bones are drilled with medical twist drills operated using a wide range of drilling speeds and feed rates. Drilling force and temperature are measured using a YDZ-II01W dynamometer and a NEC TVS-500EX thermal infrared imager, respectively, to evaluate internal bone damage. To evaluate drilling quality, bone debris and hole morphology are observed by SEM(scanning electron microscopy). Changes in drilling force and temperature give similar results during drilling such that the value of each parameter peaks just before the drill penetrates through the osteon of the compact bone into the trabeculae of the spongy bone. Drilling temperatures under physiological conditions are much lower than those observed under dry conditions, while a larger drilling force occurs under physiological conditions than dry conditions. Drilling speed and feed rate have a significant influence on drilling force, temperature, bone debris and hole morphology. The investigation of the effect of drilling force and temperature on internal bone damage reveals that a drilling speed of 4500 r/min and a feed rate of 50 mm/min are recommended for bone drilling under physiological conditions. Drilling quality peaks under these optimal parameter conditions. This paper proposes the optimal drilling parameters under mid- and high-speed surgical drilling, considering internal bone damage and drilling quality, which can be looked as a reference for surgeons performing orthopedic operations.

  1. Evaluation of Friction Stir Processing of HY-80 Steel Under Wet and Dry Conditions

    OpenAIRE

    Young, Garth William II

    2012-01-01

    This thesis describes the microstructural and mechanical property changes associated with Friction Stir Processing (FSP) of HY-80 steel under dry and underwater conditions. HY-80 is a low-carbon alloy steel that is used in a quenched and tempered condition and is highly susceptible to hydrogen assisted cracking associated with conventional fusion welding. FSW/P (400 RPM/ 2 IPM) was conducted using a polycrystalline cubic boron nitride tool having a pin length of 6.35 mm. Two sets ...

  2. What are extreme environmental conditions and how do organisms cope with them?

    Institute of Scientific and Technical Information of China (English)

    John C. WINGFIELD; J. Patrick KELLEY; Frédéric ANGELIER

    2011-01-01

    Severe environmental conditions affect organisms in two major ways. The environment may be predictably severe such as in deserts, polar and alpine regions, or individuals may be exposed to temporarily extreme conditions through weather, presence of predators, lack of food, social status etc. Existence in an extreme environment may be possible, but then to breed or molt in addition can present major bottlenecks that have resulted in the evolution of hormone-behavior adaptations to cope with unpredictable events. Examples of hormone-behavior adaptations in extreme conditions include attenuated testosterone secretion because territoriality and excess courtship may be too costly when there is one opportunity to reproduce. The individual may even become insensitive to testosterone when target areas of the brain regulating reproductive behavior no longer respond to the hormone. A second example is reduced sensitivity to glucocorticoids following acute stress during the breeding season or molt that allows successful reproduction and/or a vital renewal of the integument to endure extreme conditions during the rest of the year. Reduced sensitivity could involve: (a) modulated response of the hypothalamo-pituitary-adrenal axis, (b) reduced sensitivity to high glucocorticoid levels, or (c) a combination of (a) and (b). Moreover, corticosteroid binding proteins (CBP) buffer responses to stress by reducing the movement of glucocorticoids into target cells. Finally, intracellular enzymes (11β-hydroxysteroid dehy-drogenase and variants) can deactivate glucocorticoids entering cells thus reducing interaction with receptors. These mechanisms have important implications for climate change and increasing extremes of weather.

  3. Optimization of spray drying conditions for production of quality pomegranate juice powder

    OpenAIRE

    Khalid Muzaffar; Bijamwar Vilas Dinkarrao; Pradyuman Kumar

    2016-01-01

    The present study was aimed to optimize the spray drying operating parameters for the production of quality pomegranate juice powder using response surface methodology. The spray drying operating conditions including inlet air temperature (170–190°C), feed flow rate (18–30 mL/min), and blower speed varied (2,000–2,400 rpm) were used as independent variables. The responses evaluated were ascorbic acid content, anthocyanin content, moisture content, hygroscopicity, and water solubility index. S...

  4. Dielectric Spectroscopy of Bisphenol A Epoxy Resin Aged in Wet and Dry Conditions

    OpenAIRE

    2009-01-01

    This thesis presents the laboratory test data on Bisphenol A epoxy insulation.This thesis work deals with electrical, mechanical and thermal analysis of Bisphenol A epoxy resin. The main aim of this thesis work was to examine if dry and wet aging changes the glass transition temperature (Tg) of the epoxies and measure the impact on the complex permittivity under different ageing conditions namely dry and wet. During ageing the samples (epoxy discs and dog bones) were kept in water at 20°C, 45...

  5. Effect of Alloying Additions on the Oxidation of High Speed Steels under Dry and Wet Conditions

    Institute of Scientific and Technical Information of China (English)

    F.C. RIZZO; M.J.MONTEIRO; S.R.J.SAUNDERS

    2009-01-01

    An investigation has been carried out into the effects of chromium and vanadium content on the oxidation rate and on the adhesion of oxide scales grown on three different chemical compositions of high speed steels under dry and wet conditions. The oxidation tests were carried out in a thermobalance at 650 ℃ for up to 14.4 ks. The mass gain of the specimens increased with increasing contents of water vapour. Alloy composition had no effect on the oxidation rate in dry conditions. The "adhesion" of the oxide scale was determined using indentation with a Rockwell C diamond and the pull adhesion test to determine the interfacial toughness and the tensile strength of the oxide metal bond, respectively. Generally, the results of the investigation indicated that oxide adhesion was lowest for the specimens exposed to dry conditions, and that with increasing water vapour content, the scale was more adherent. Indentation test results showed that an increase in the Ⅴ concentration was deleterious to oxidc adhesion in both the dry and wet environments, whereas an increase in the Cr-content had little effect on adhesion.

  6. Optimization of Freeze Drying Conditions for Purified Pectinase from Mango (Mangifera indica cv. Chokanan Peel

    Directory of Open Access Journals (Sweden)

    Abdul Manap Mohd Yazid

    2012-03-01

    Full Text Available Response surface methodology (RSM along with central composite design (CCD was applied to optimize the freeze drying conditions for purified pectinase from mango (Mangifera indica cv. Chokanan peel. The effect of pectinase content (−2.66, 62.66 mg/mL, Arabic gum (−1.21, 10.21%, w/v, and maltodextrin (0.73, 7.26%, w/v as independent variables on activity, yield, and storage stability of freeze-dried enzyme was evaluated. Storage stability of pectinase was investigated after one week at 4 °C and yield percentage of the enzyme after encapsulation was also determined. The independent variables had the most significant (p < 0.05 effect on pectinase activity and yield of the enzyme. It was observed that the interaction effect of Arabic gum and maltodextrin improved the enzymatic properties of freeze-dried pectinase. The optimal conditions for freeze-dried pectinase from mango peel were obtained using 30 mg/mL of pectinase content, 4.5 (%, w/v of Arabic gum, and 4 (%, w/v of maltodextrin. Under these conditions, the maximum activity (11.12 U/mL, yield (86.4% and storage stability (84.2% of encapsulated pectinase were achieved.

  7. Dry co-digestion of sewage sludge and rice straw under mesophilic and thermophilic anaerobic conditions.

    Science.gov (United States)

    Chu, Xiangqian; Wu, Guangxue; Wang, Jiaquan; Hu, Zhen-Hu

    2015-12-01

    Dry anaerobic digestion of sewage sludge can recover biogas as energy; however, its low C/N ratio limits it as a single substrate in the anaerobic digestion. Rice straw is an abundant agricultural residue in China, which is rich in carbon and can be used as carbon source. In the present study, the performance of dry co-digestion of sewage sludge and rice straw was investigated under mesophilic (35 °C) and thermophilic (55 °C) conditions. The operational factors impacting dry co-digestion of sewage sludge and rice straw such as C/N ratio, moisture content, and initial pH were explored under mesophilic conditions. The results show that low C/N ratios resulted in a higher biogas production rate, but a lower specific biogas yield; low moisture content of 65 % resulted in the instability of the digestion system and a low specific biogas yield. Initial pH ranging 7.0-9.0 did not affect the performance of the anaerobic digestion. The C/N ratio of 26-29:1, moisture content of 70-80 %, and pH 7.0-9.0 resulted in good performance in the dry mesophilic co-digestion of sewage sludge and rice straw. As compared with mesophilic digestion, thermophilic co-digestion of sewage sludge and rice straw significantly enhanced the degradation efficiency of the substrates and the specific biogas yield (p co-digestion of sewage sludge under mesophilic and thermophilic conditions.

  8. Modeling evaporation processes in a saline soil from saturation to oven dry conditions

    Directory of Open Access Journals (Sweden)

    M. Gran

    2011-07-01

    Full Text Available Thermal, suction and osmotic gradients interact during evaporation from a salty soil. Vapor fluxes become the main water flow mechanism under very dry conditions. A coupled nonisothermal multiphase flow and reactive transport model was developed to study mass and energy transfer mechanisms during an evaporation experiment from a sand column. Very dry and hot conditions, including the formation of a salt crust, necessitate the modification of the retention curve to represent oven dry conditions. Experimental observations (volumetric water content, temperature and concentration profiles were satisfactorily reproduced using mostly independently measured parameters, which suggests that the model can be used to assess the underlying processes. Results show that evaporation concentrates at a very narrow front and is controlled by heat flow, and limited by salinity and liquid and vapor fluxes. The front divides the soil into a dry and saline portion above and a moist and diluted portion below. Vapor diffusses not only upwards but also downwards from the evaporation front, as dictated by temperature gradients. Condensation of this downward flux causes dilution, so that salt concentration is minimum and lower than the initial one, just beneath the evaporation front. While this result is consistent with observations, it required adopting a vapor diffusion enhancement factor of 8.

  9. Proceedings of the second symposium on science of hadrons under extreme conditions

    Energy Technology Data Exchange (ETDEWEB)

    Chiba, Satoshi [ed.

    2000-08-01

    The second symposium on Science of Hadrons under Extreme Conditions, organized by the Research Group for Hadron Science, Advanced Science Research Center, was held at Tokai Research Establishment of JAERI on January 24 to 26, 2000. The symposium was devoted for discussions and presentations of research results in wide variety of fields such as nuclear matter, high-energy nuclear reactions, quantum chromodynamics, supernovae and nucleosynthesis to understand various aspects of hadrons under extreme conditions. The 26 of the presented papers are indexed individually. (J.P.N.)

  10. Conditional Second Order Short-crested Water Waves Applied to Extreme Wave Episodes

    DEFF Research Database (Denmark)

    Jensen, Jørgen Juncher

    2005-01-01

    A derivation of the mean second order short-crested wave pattern and associated wave kinematics, conditional on a given magnitude of the wave crest, is presented. The analysis is based on the second order Sharma and Dean finite water wave theory. A comparison with a measured extreme wave profile......, the Draupner New Year Wave, shows a good agreement in the mean, indicating that this second order wave can be a good identifier of the shape and occurrence of extreme wave events. A discussion on its use as an initial condition for a fully non-linear three-dimensional surface wave analysis is given....

  11. Dry matter yield of improved alpine grasslands depending on climate conditions

    Directory of Open Access Journals (Sweden)

    Vasile Mocanu

    2014-11-01

    Full Text Available Normal 0 false false false EN-US X-NONE X-NONE MicrosoftInternetExplorer4 Climate conditions in any land area have a direct influence on the productivity level of natural ecosystems and agroecosystems. To assess the yield per area unit, we took into account the amounts of dry matter depending on temperature (10C and precipitations (1 mm during vegetation. During the experimental period, the mean annual temperature during vegetation was 9430C, with variations between 7750C (1997 and 1,1750C (2012. This multiannual variation of the thermal constant also influenced the level of dry matter yield per 10C, which ranged between 2.14 kg DM/10C and 9.08 kg DM/10C. As for the amounts of precipitations, dry matter yield varied between 6.02 kg DM/1 mm (2002 and 29.11 kg DM/1 mm (2003.

  12. Spent nuclear fuel project cold vacuum drying facility process water conditioning system design description

    Energy Technology Data Exchange (ETDEWEB)

    IRWIN, J.J.

    1998-11-30

    This document provides the System Design Description (SDD) for the Cold Vacuum Drying Facility (CVDF) Process Water Conditioning (PWC) System. The SDD was developed in conjunction with HNF-SD-SNF-SAR-002, Safety Analysis Report for the Cold Vacuum Drying Facility, Phase 2, Supporting Installation of Processing Systems (Garvin 1998), the HNF-SD-SNF-DRD-O02, 1998, Cold Vacuum Drying Facility Design Requirements, and the CVDF Design Summary Report. The SDD contains general descriptions of the PWC equipment, the system functions, requirements and interfaces. The SDD provides references for design and fabrication details, operation sequences and maintenance. This SDD has been developed for the SNFP Operations Organization and shall be updated, expanded, and revised in accordance with future design, construction and startup phases of the CVDF until the CVDF final ORR is approved.

  13. Influence of drying conditions on the effective moisture diffusivity and energy requirements during the drying of pretreated and untreated pumpkin

    Energy Technology Data Exchange (ETDEWEB)

    Tunde-Akintunde, Toyosi Y.; Ogunlakin, Grace O. [Ladoke Akintola University of Technology, PMB 4000, Ogbomoso, Oyo State (Nigeria)

    2011-02-15

    Pumpkin as a fruit is consumed by both animals and humans. Its high moisture content makes it perishable and thus there is a need for drying as a means of preservation. Thin-layer drying characteristics for the samples dried using a hot-air dryer were obtained from the experiment data. The drying was observed to take place in the falling rate drying period. Ficks law was used to determine the moisture diffusivity which varied from a minimum of 1.19 x 10{sup -9} m{sup 2}/s for untreated pumpkin samples dried at 40 C to a maximum value of 4.27 x 10{sup -9} m{sup 2}/s for steam blanched samples dried at 80 C. The value of the energy of activation varied from 21.44 to 28.67 kJ/mol. The input energy values and specific energy requirement for thin-drying of pumpkin samples were found to be in the range of 317.8-458.1 kW h and 1588.8-2290.3 kW h/kg from 40 C to 80 C with a drying air velocity of 1.5 m/s respectively. (author)

  14. Modeling evaporation processes in a saline soil from saturation to oven dry conditions

    Directory of Open Access Journals (Sweden)

    M. Gran

    2011-01-01

    Full Text Available Thermal, suction and osmotic gradients interact during evaporation from a salty soil. Vapor fluxes become the main water flow mechanism under very dry conditions. A coupled nonisothermal multiphase flow and a reactive transport model of a salty sand soil was developed to study such an intricate system. The model was calibrated with data from an evaporation experiment (volumetric water content, temperature and concentration. The retention curve and relative permeability functions were modified to simulate oven dry conditions. Experimental observations were satisfactorily reproduced, which suggests that the model can be used to assess the underlying processes. Results show that evaporation is controlled by heat, and limited by salinity and liquid and vapor fluxes. Below evaporation front vapor flows downwards controlled by temperature gradient and thus generates a dilution. Vapor diffusion and dilution are strongly influenced by heat boundary conditions. Gas diffusion plays a major role in the magnitude of vapor fluxes.

  15. Molecular formula composition of β-caryophyllene ozonolysis SOA formed in humid and dry conditions

    Science.gov (United States)

    Kundu, Shuvashish; Fisseha, Rebeka; Putman, Annie L.; Rahn, Thom A.; Mazzoleni, Lynn R.

    2017-04-01

    We studied the molecular formula composition of six β-caryophyllene SOA samples using ultrahigh resolution Fourier transform ion cyclotron resonance mass spectrometry under various reaction conditions. The SOA samples were generated in dry or low relative humidity (RH) chamber conditions with or without cyclohexane. All of the studied SOA mass spectra have three distinct clusters of hundreds of negative ions referred to as Group I (100 molecular formulas with higher average carbon numbers were observed in humid SOA than in dry SOA in the absence of cyclohexane, suggesting a decrease of cleavage reactions in humid condition. This study characterizes β-caryophyllene ozonolysis SOA based on ultrahigh mass resolution and demonstrates the significance of humidity in terms of the molecular distributions and relative abundances of the analytes. We also discuss the possible mechanism for the formation of Group I-III compounds based on the current understanding of SOA formation in the atmosphere.

  16. Evolution of self-organization in nano-structured PVD coatings under extreme tribological conditions

    Energy Technology Data Exchange (ETDEWEB)

    Fox-Rabinovich, G., E-mail: gfox@mcmaster.ca [Department of Mechanical Engineering, McMaster University, 1280 Main St. W., Hamilton, ON, Canada L8S 4L7 (Canada); Kovalev, A. [Surface Phenomena Researches Group, CNIICHERMET, 9/23, 2-nd Baumanskaya Street, Moscow 105005 (Russian Federation); Aguirre, M.H. [Laboratory of Advanced Microscopy, Institute of Nanoscience of Aragón, University of Zaragoza, 50018 Zaragoza (Spain); Yamamoto, K. [Materials Research Laboratory, Kobe Steel Ltd, 1-5-5 Takatsuda-dai, Nishi-ku, Kobe 651-2271, Hyogo (Japan); Veldhuis, S. [Department of Mechanical Engineering, McMaster University, 1280 Main St. W., Hamilton, ON, Canada L8S 4L7 (Canada); Gershman, I. [All-Russian Railway Research Institute, 10 Third Mytishchinskaya Street, Moscow 29851 (Russian Federation); Rashkovskiy, A. [Surface Phenomena Researches Group, CNIICHERMET, 9/23, 2-nd Baumanskaya Street, Moscow 105005 (Russian Federation); Endrino, J.L. [Albengoa Research, Energia Solar 1, Palmas Altas, Seville 41014 (Spain); Beake, B. [Micro Materials Limited, Willow House, Yale Business Village, Ellice Way, Wrexham LL13 7YL (United Kingdom); Dosbaeva, G. [Department of Mechanical Engineering, McMaster University, 1280 Main St. W., Hamilton, ON, Canada L8S 4L7 (Canada); Wainstein, D. [Surface Phenomena Researches Group, CNIICHERMET, 9/23, 2-nd Baumanskaya Street, Moscow 105005 (Russian Federation); Yuan, Junifeng; Bunting, J.W. [Department of Mechanical Engineering, McMaster University, 1280 Main St. W., Hamilton, ON, Canada L8S 4L7 (Canada)

    2014-04-01

    Highlights: • The evolution of self-organization under extreme frictional conditions has been studied. • Comprehensive characterization of the tribo-films was made using various surface analytical techniques. • During the running-in stage, mullite tribo-ceramics predominate on the surface of the nano-multilayer coating, establishing a functional hierarchy within the layer of tribo-films. • It is possible to control tribo-film evolution during self-organization by means of an increase in structural complexity and the non-equilibrium state of the surface engineered layer. - Abstract: The evolution of the self-organization process where dissipative structures are formed under the extreme frictional conditions associated with high performance dry machining of hardened steels has been studied in detail. The emphasis was on the progressive studies of surface transformations within multilayer and monolayer TiAlCrSiYN-based PVD coatings during the running-in stage of wear when self-organization process occurs. The coating layer was characterized by high resolution electron energy-loss spectroscopy (HREELS). It is shown that the nano-multilayer coating possesses higher non-equilibrium structure in comparison to the monolayer. Comprehensive studies of the tribo-films (dissipative structures) formed on the friction surface were made using a number of advanced surface characterization techniques such as X-ray photoelectron spectroscopy (XPS) and X-ray absorption near edge structure (XANES). The data obtained for the tribo-films was combined with the detailed TEM studies of the structural and phase transformations within the underlying coating layer. This data was related to the micro-mechanical characteristics of the coating layer and its wear resistance. It was demonstrated that the evolution of the self-organization process is strongly controlled by the characteristics of the tribo-films formed at different stages of the wear process. Within running-in stage (after

  17. Analysis of air-conditioning and drying processes using spreadsheet add-in for psychrometric data

    Directory of Open Access Journals (Sweden)

    E.O. Diemuodeke

    2010-01-01

    Full Text Available A spreadsheet add-in for the psychrometric data at any barometric pressure and in the air-conditioning and drying temperatureranges was developed using appropriate correlations. It was then used to simulate and analyse air-conditioning and dryingprocesses in the Microsoft Excel environment by exploiting its spreadsheet and graphic potentials. The package allowsone to determine the properties of humid air at any desired state, and to simulate and analyse air-conditioning as well asdrying processes. This, as a teaching tool, evokes the intellectual curiosity of students and enhances their interest and abilityin the thermodynamics of humid-air processes.

  18. Computer-Aided Framework for the Design of Freeze-Drying Cycles: Optimization of the Operating Conditions of the Primary Drying Stage

    Directory of Open Access Journals (Sweden)

    Davide Fissore

    2015-05-01

    Full Text Available This paper deals with the freeze-drying process and, in particular, with the optimization of the operating conditions of the primary drying stage. When designing a freeze-drying cycle, process control aims at obtaining the values of the operating conditions (temperature of the heating fluid and pressure in the drying chamber resulting in a product temperature lower than the limit value of the product, and in the shortest drying time. This is particularly challenging, mainly due to the intrinsic nonlinearity of the system. In this framework, deep process knowledge is required for deriving a suitable process dynamic model that can be used to calculate the design space for the primary drying stage. The design space can then be used to properly design (and optimize the process, preserving product quality. The case of a product whose dried layer resistance, one of the key model parameters, is affected by the operating conditions is addressed in this paper, and a simple and effective method to calculate the design space in this case is presented and discussed.

  19. Optimization of spray drying conditions for production of quality pomegranate juice powder

    Directory of Open Access Journals (Sweden)

    Khalid Muzaffar

    2016-12-01

    Full Text Available The present study was aimed to optimize the spray drying operating parameters for the production of quality pomegranate juice powder using response surface methodology. The spray drying operating conditions including inlet air temperature (170–190°C, feed flow rate (18–30 mL/min, and blower speed varied (2,000–2,400 rpm were used as independent variables. The responses evaluated were ascorbic acid content, anthocyanin content, moisture content, hygroscopicity, and water solubility index. Statistical analysis showed that among the independent variables, inlet air temperature showed greater effect on all the investigated responses. The derived optimum conditions were used for the powder production to check the validity of the quadratic model. Small deviations were observed between the experimental values and the predicted ones and the values were within the acceptable limits. The results showed that the optimum spray drying operating conditions for the production of pomegranate juice powder with optimum quality were 171°C inlet temperature, 30 mL/min feed flow rate, and 2,400 rpm blower speed. Under these optimum conditions, quality pomegranate juice powder with desirable properties of high content of vitamin C and anthocyanin, low moisture content, low hygroscopicity, and high solubility could be produced.

  20. Tribological characteristics of C/C-SiC braking composites under dry and wet conditions

    Institute of Scientific and Technical Information of China (English)

    LI Zhuan; XIAO Peng; XIONG Xiang; ZHU Su-hua

    2008-01-01

    C/C-SiC braking composites, based on reinforcement of carbon fibers and rnatrices of carbon and silicon carbide, were fabricated by warm compaction and in situ reaction process. The tribological characteristics of C/C-SiC braking composites under dry and wet conditions were investigated by means of MM-1000 type of friction testing machine. The influence of dry and wet conditions on the tribological characteristics of the C/C-SiC composites was ascertained. Under dry condition, C/C-SiC braking composites show superior tribological characteristics, including high coefficient of friction (0.38), good abrasive resistance (thickness loss is 1.10 μm per cycle) and steady breaking. The main wear mechanism is plastic deformation and abrasion caused by plough. Under wet condition, frictional films form on the worn surface. The coefficient of friction (0.35) could maintain mostly, and the thickness loss (0.70 μm per cycle) reduces to a certain extent. Furthermore, braking curves are steady and adhesion and oxidation are the main wear mechanisms.

  1. Comparison of Extreme Pressure Additive Treat Rates in Soybean and Mineral Oils Under Boundary Lubrication Conditions

    Science.gov (United States)

    Traditionally, it is considered that, under boundary lubrication conditions, the reduction in friction and wear is mostly dependent on Extreme Pressure (EP) additives, rather than the basestock. However, several studies indicate that vegetable oils also contribute to the lubricity under this regime...

  2. The Extreme Male Brain Theory and Gender Role Behaviour in Persons with an Autism Spectrum Condition

    Science.gov (United States)

    Stauder, J. E. A.; Cornet, L. J. M.; Ponds, R. W. H. M.

    2011-01-01

    According to the Extreme Male Brain theory persons with autism possess masculinised cognitive traits. In this study masculinisation of gender role behaviour is evaluated in 25 persons with an autism spectrum condition (ASC) and matched controls with gender role behaviour as part of a shortened version of the Minnesota Multiphasic Personality…

  3. The Extreme Male Brain Theory and Gender Role Behaviour in Persons with an Autism Spectrum Condition

    Science.gov (United States)

    Stauder, J. E. A.; Cornet, L. J. M.; Ponds, R. W. H. M.

    2011-01-01

    According to the Extreme Male Brain theory persons with autism possess masculinised cognitive traits. In this study masculinisation of gender role behaviour is evaluated in 25 persons with an autism spectrum condition (ASC) and matched controls with gender role behaviour as part of a shortened version of the Minnesota Multiphasic Personality…

  4. Special Features of the Carbonitriding of Parts of Instrument Bearings Designed for Extreme Service Conditions

    Science.gov (United States)

    Smirnov, A. E.; Shevchenko, S. Yu.; Shchipunov, V. S.; Kunyaev, V. E.; Seval'nev, G. S.

    2016-09-01

    A study is made of complexly alloyed steel 8Kh4V9F2-Sh, which is used for fabricating parts of engineering bearings operating under extreme conditions. Vacuum processes are shown to be preferable to gas carburizing for hardening the races of precision bearings. Vacuum carburizing is shown to be an effective technique for forming quality diffusion layers.

  5. Combined effects of graphite and sulfide on the tribological properties of bronze under dry conditions

    Directory of Open Access Journals (Sweden)

    Yoshimasa Hirai

    2016-12-01

    Full Text Available The present study describes the tribological properties of penetrated-graphite bronze containing micro-sized sulfide under dry conditions. The graphite penetration was carried out by means of roller burnishing. Micro shot peening was also applied in order to fabricate micro dimples in the penetrated graphite. The graphite area fraction was approximately 50%. The tribological properties were evaluated using a face-to-face type testing apparatus under dry conditions. The results showed that the friction coefficient of the sulfide-containing bronze decreased and the seizure resistance properties significantly increased. The friction distance until seizure occurrence was improved to more than 2.5 times. Furthermore, the friction coefficient was low and stable until the end of the experiment. It was inferred that the friction resistance was decreased and stabilized when the transfer layer was without Fe content.

  6. Retention of short chain fatty acids under drying and storage conditions

    Directory of Open Access Journals (Sweden)

    Alexandre Santos Souza

    2011-09-01

    Full Text Available Cheese whey permeate was used as a substrate for the fermentation of Propionibacterium freudenreichi PS1 for the production of short chain fatty acids, components of the bio-aroma of Swiss cheese. The liquid bio-aroma was encapsulated by spray drying under different conditions of air inlet temperature and feed rate. A study was carried out on the stability of the bio-aroma during storage in laminated packages at 30 °C for 96 days using the product showing the greatest retention of acetic and propionic acids. The results showed that the best drying conditions were an air entrance temperature of 180 °C and a feed rate of 24 g/min resulting in particles with a smooth surface and few invaginations and micro-fissures. However, 72% of the acetic acid and 80% of the propionic acid were lost during storage showing that the wall material used was inadequate to guarantee product stability.

  7. DETERMINATION OF WATER AND DRY MATTER IN ORNAMENTAL TREES UNDER THE CLIMATIC CONDITIONS OF IASI

    Directory of Open Access Journals (Sweden)

    Carmen Lamban

    2015-12-01

    Full Text Available This paper presents some results concerning the determination of water and dry matter through the quantitative gravimetric method in ornamental trees (leaves and branches of Juniperus, Thuja, Chamaecyparis, Picea, Pinus, Abies, Pseudotzuga genera, under the climatic conditions of Iasi. The purpose of carrying on this work is to see if moisture of vegetative part remains under normal limits. The success of propagation, planting, transplanting of woody plants is largely dependant on the presence of water.

  8. The Effect of Body Weight on Heat Strain Indices in Hot and Dry Climatic Conditions

    Directory of Open Access Journals (Sweden)

    Habibi

    2016-03-01

    Full Text Available Background Being overweight is a characteristic that may influence a person’s heat exchange. Objectives The purpose of this study was to assess the effect of body weight on heat strain indices in hot and dry climatic conditions. Materials and Methods This study was completed with a sample of 30 participants with normal weights, as well as 25 participants who were overweight. The participants were physically inactive for a period of 120 minutes in a climatic chamber with hot and dry conditions (22 - 32°C and with 40% relative humidity (RH.The physiological strain index (PSI and heat strain score index (HSSI questionnaires were used. Simultaneous measurements were completed during heat exposure for periods of five minutes. The resting periods acted as the initial measurements for 15 minutes. Results In both groups, oral temperature, heart rate, and thermal perceptual responses increased during heat exposure. The means and standard deviations of heart rate and oral temperature were gathered when participants were in hot and dry climatic conditions and were not physically active. The heart rates and oral temperatures were 79.21 ± 5.93 bpm and 36.70 ± 0.45°C, respectively, for those with normal weights. For overweight individuals, the measurements for heart rate and oral temperature reached 82.21 ± 8.9 bpm and 37.84 ± 0.37°C, respectively. Conclusions The results showed that, compared to participants with normal weights, physiological and thermal perceptual responses were higher in overweight participants. Therefore, overweight individuals should avoid hot/dry weather conditions to decrease the amount of heat strain.

  9. The determination of optimum condition in water hyacinth drying process by mixed adsorption drying method and modified fly ash as an adsorbent

    Science.gov (United States)

    Saputra, Asep Handaya; Putri, Rizky Anggreini

    2017-05-01

    Water hyacinth is an aquatic weed that has a very fast growth which makes it becomes a problem to the ecosystem. On the other hand, water hyacinth has a high fiber content (up to 20% by weight) which makes it potential to become raw material for composites and textile industries. As an aquatic plant, water hyacinth has a high initial moisture content that reaches more than 90%. Meanwhile the moisture content of fiber as a raw material for composite and textile industry should not be more than 10% to maintain the good quality of the products. Mixed adsorption drying method is one of the innovative method that can replace conventional drying process. Fluidization method which has been commonly used in agricultural and pharmaceutical products drying, can be enhanced by combining it with the adsorption method as performed in this study. In mixed fluidization-adsorption drying method, fly ash as adsorbent and water hyacinth fiber were put together into the fluidization column where the drying air evaporate the moisture content in water hyacinth fiber. In addition, the adsorbent adsorb the moisture content in the drying air to make the moisture content of the drying air remain low. The drying process is performed in various temperature and composition of water hyacinth and adsorbent in order to obtain the optimum drying condition. In addition, the effect of fly ash pellet and fly ash powder to the drying process was also performed. The result shows that the higher temperature and the more amount of adsorbent results in the faster drying rate. Fly ash pellet shows a better adsorption since it has a smaller pore diameter and wider surface area. The optimum temperature obtained from this study is 60°C and the optimum ratio of water hyacinth and fly ash is 50:50.

  10. High Temperature Oxidation Behavior of T91 Steel in Dry and Humid Condition

    Directory of Open Access Journals (Sweden)

    Yonghao Leong

    2016-09-01

    Full Text Available High temperature oxidation behavior of T91 ferritic/martensitic steel was examined over the temperature range of 500 to 700°C in dry and humid environments.  The weight gain result revealed that oxidation occurs at all range of temperatures and its rate is accelerated by increasing the temperature. The weight gain of the oxidized steel at 700°C in steam condition was six times bigger than the dry oxidation.. SEM/EDX of the cross-sectional image showed that under dry condition, a protective and steady growth of the chromium oxide (Cr2O3 layer was formed on the steel with the thickness of 2.39±0.34 µm. Meanwhile for the humid environment, it is found that the iron oxide layer, which consists of the hematite (Fe2O3 and magnetite (Fe3O4 was formed as the outer scale, and spinnel as inner scale. This result indicated that the oxidation behavior of T91 steel was affected by its oxidation environment. The existence of water vapor in steam condition may prevent the formation of chromium oxide as protective layer.

  11. Causes of the Extreme Dry Conditions Over California During Early 2013

    Science.gov (United States)

    Wang, Hailan; Schubert, Siegfried D.

    2014-01-01

    The 2013 SST anomalies produced a predilection for California drought, whereas the long-term warming trend appears to make no appreciable contribution because of the counteraction between its dynamical and thermodynamic effects.

  12. Frontiers of Optical Spectroscopy Investigating Extreme Physical Conditions with Advanced Optical Techniques

    CERN Document Server

    Bartolo, Baldassare

    2005-01-01

    Advanced spectroscopic techniques allow the probing of very small systems and very fast phenomena, conditions that can be considered "extreme" at the present status of our experimentation and knowledge. Quantum dots, nanocrystals and single molecules are examples of the former and events on the femtosecond scale examples of the latter. The purpose of this book is to examine the realm of phenomena of such extreme type and the techniques that permit their investigations. Each author has developed a coherent section of the program starting at a somewhat fundamental level and ultimately reaching the frontier of knowledge in the field in a systematic and didactic fashion. The formal lectures are complemented by additional seminars.

  13. Matter under extreme conditions probed by a seeded free-electron-laser

    Energy Technology Data Exchange (ETDEWEB)

    Bencivenga, F.; Principi, E.; Cucini, R.; Danailov, M. B.; Demidovich, A.; D’Amico, F.; Di Fonzo, S.; Gessini, A.; Kurdi, N.; Mahne, N.; Raimondi, L.; Zangrando, M.; Masciovecchio, C. [Elettra-Sincrotrone Trieste S.C.p.A., S.S. 14 km 163,5 in AREA Science Park, 34149 Basovizza (Italy); Giangrisostomi, E.; Battistoni, A.; Svetina, C. [Elettra-Sincrotrone Trieste S.C.p.A., S.S. 14 km 163,5 in AREA Science Park, 34149 Basovizza (Italy); Dipartimento di Fisica, Universita di Trieste, Piazzale Europa, 34127 Trieste (Italy); Di Cicco, A.; Gunnella, R.; Hatada, K. [CNISM, Dipartimento di Fisica, Universita' di Camerino, Via Madonna delle Carceri, 62032 Camerino (Italy); Filipponi, A. [Dipartimento di Scienze Fisiche e Chimiche, Universita' dell’Aquila, Via Vetoio, 67100 L’Aquila (Italy); and others

    2015-08-17

    FERMI is the first user dedicated seeded free-electron-laser (FEL) working in the extreme ultraviolet (XUV) and soft x-ray range. The EIS-TIMEX experimental end-station was availabe to external users since from the beginning of the user operation of the facility, in Dicember 2012. EIS-TIMEX has been conceived to exploit the unique properties of the FERMI source to study matter under extreme and metastable thermodynamic conditions. We hereby report on its basic parameters and applications, which includes very low jitter (i.e., high time resolution) pump-probe measurements.

  14. Influence of the emotional state on behavior in extreme conditions of competitive sports activities

    Directory of Open Access Journals (Sweden)

    Malakhov V.A.

    2014-03-01

    Full Text Available Purpose : establish a communication pattern of emotional intensity and level of extreme environment in which activity is performed. Materials : in the study involved 600 men aged 18-22 years. Results : the effect of the emotional state on the efficiency of the motor activity that flowed under extreme conditions. Set individual characteristics flow sports activities in extreme conditions. First used in the special semantic space for the orderly presentation of research results parachute jumps. The monogram built in semantic fields allows to establish the frequency response range of individual heartbeats and the optimal frequency for maximum performance. On the basis of established regularities of the "reflex of readiness" assessment methodology given emotional stress, which reflects the readiness of an individual to perform a parachute jump. An objective indicator of preparedness measures is a violation of the symmetry of the flow and haptic reflex and serial dynamometry. Conclusions : in using semantic spaces reflects the flowing of reflex of biological caution and accompaniment reflex. In the basis of constructing estimates of emotional stress are the regularities of mean arterial pressure as nonspecific reactions. Measure of extent of confused is estimated by variability of accompaniment reflex. Breach of symmetry in mean arterial pressure and the amplitude - frequency response accompaniment reflex, determine the validity of staying in extreme conditions. Introduction of the measure in using semantic spaces allows by selective data to establish the overall structure of the studied process.

  15. Effects of impregnation methods and drying conditions on quinoline hydrodenitrogenation over Ni-W based catalysts

    Energy Technology Data Exchange (ETDEWEB)

    Guo, Fang; Qiu, Zegang; Zhao, Liangfu; Xiang, Hongwei [Institute of Coal Chemistry, Chinese Academy of Sciences (China); Guo, Shaoqing [Taiyuan University of Science and Technology (China)

    2014-04-15

    The effects of impregnation methods (co-impregnation and sequential impregnation) and drying conditions (air and vacuum) on the structure and catalytic behavior of MCM-41 supported Ni-W catalysts were investigated. The catalysts were characterized by powder X-ray diffraction (XRD) analysis, Fourier-transform infrared spectroscopy (FT-IR), diffuse reflectance UV-Vis absorbance spectroscopy (DRS), Raman spectroscopy, X-ray photoelectron spectroscopy (XPS) and pyridine adsorbed infrared spectroscopy (Py-IR) techniques. They were tested for hydrodenitrogenation (HDN) of quinoline at temperatures of 300-400 deg C. The HDN results showed that the catalysts prepared by co-impregnation were more active than the catalysts prepared by sequential impregnation and the catalysts prepared by drying under vacuum were more active than the catalysts dried in air. Characterization revealed that the co-impregnation method and drying under vacuum promoted the dispersion of W, the formation of the active phases, and the formation of acidic sites on the catalysts. (author)

  16. Optimisation of spray drying operating conditions of Morinda citrifolia L. fruit extract using response surface methodology

    Directory of Open Access Journals (Sweden)

    Duduku Krishnaiah

    2015-01-01

    Full Text Available A conventional solvent extract of Morinda citrifolia L. fruit was spray dried using adjuvant maltodextrin (5 wt.%. Spray drying was carried out according to the D-optimal design, and the independent variables selected were temperature and Mcore/Mwall. The spray drying process was optimised by using response surface methodology (RSM for four different responses: moisture content (MC, DPPH scavenging activity, total phenolic content (TPC, and total flavonoid (TF. The effects of temperature and of the core to wall material ratio were found to be significant for all responses. The optimal spray drying condition for maltodextrin as binding material was found to be 1:1.5 (Mcore/Mwall, volume ratio of M. citrifolia L. extract to additive solution at 95 °C. The experimental values of the response variables correspond well to the predicted values. The microparticles obtained in this study represent an interesting food additive for incorporation into functional foods due to the presence of antioxidants.

  17. Adhesive Wear Performance of CFRP Multilayered Polyester Composites Under Dry/wet Contact Conditions

    Science.gov (United States)

    Danaelan, D.; Yousif, B. F.

    The tribo-performance of a new engineering composite material based on coconut fibers was investigated. In this work, coconut fibers reinforced polyester (CFRP) composites were developed. The tribo-experiments were conducted by using pin-on-disc machine under dry and wet sliding contact condition against smooth stainless steel counterface. Worn surfaces were observed using optical microscope. Friction coefficient and specific wear rate were presented as a function of sliding distance (0-0.6 km) at different sliding velocities (0.1-0.28 m/s). The effect of applied load and sliding velocity was evaluated. The results showed that all test parameters have significant influence on friction and wear characteristics of the composites. Moreover, friction coefficient increased as the normal load and speed increased, the values were about 0.7-0.9 under dry contact condition. Meanwhile, under wet contact condition, there was a great reduction in the friction coefficient, i.e. the values were about 0.1-0.2. Furthermore, the specific wear rates were found to be around 2-4 (10-3) mm3/Nm under dry contact condition and highly reduced under wet condition. In other words, the presence of water as cleaner and polisher assisted to enhance the adhesive wear performance of CFRP by about 10%. The images from optical microscope showed evidence of adhesive wear mode with transition to abrasive wear mode at higher sliding velocities due to third body abrasion. On the other hand, optical images for wet condition showed less adhesive wear and smooth surfaces.

  18. What are extreme environmental conditions and how do organisms cope with them?

    Directory of Open Access Journals (Sweden)

    John C. WINGFIELD, J. Patrick KELLEY, Frédéric ANGELIER

    2011-06-01

    Full Text Available Severe environmental conditions affect organisms in two major ways. The environment may be predictably severe such as in deserts, polar and alpine regions, or individuals may be exposed to temporarily extreme conditions through weather, presence of predators, lack of food, social status etc. Existence in an extreme environment may be possible, but then to breed or molt in addition can present major bottlenecks that have resulted in the evolution of hormone-behavior adaptations to cope with unpredictable events. Examples of hormone-behavior adaptations in extreme conditions include attenuated testosterone secretion because territoriality and excess courtship may be too costly when there is one opportunity to reproduce. The individual may even become insensitive to testosterone when target areas of the brain regulating reproductive behavior no longer respond to the hormone. A second example is reduced sensitivity to glucocorticoids following acute stress during the breeding season or molt that allows successful reproduction and/or a vital renewal of the integument to endure extreme conditions during the rest of the year. Reduced sensitivity could involve: (a modulated response of the hypothalamo-pituitary-adrenal axis, (b reduced sensitivity to high glucocorticoid levels, or (c a combination of (a and (b. Moreover, corticosteroid binding proteins (CBP buffer responses to stress by reducing the movement of glucocorticoids into target cells. Finally, intracellular enzymes (11b-hydroxysteroid dehydrogenase and variants can deactivate glucocorticoids entering cells thus reducing interaction with receptors. These mechanisms have important implications for climate change and increasing extremes of weather [Current Zoology 57 (3: 363–374, 2011].

  19. Radiation inactivation of microorganisms on food materials with different dry conditions

    Energy Technology Data Exchange (ETDEWEB)

    Ryomoto, Yasuhisa; Ito, Hitoshi [Japan Atomic Energy Research Inst., Takasaki, Gunma (Japan). Takasaki Radiation Chemistry Research Establishment

    2001-09-01

    The effect of dry condition of food materials such as spices or herbs with grain or powder were investigated for inactivation of microorganisms by gamma-rays or electron-beams. Radiation sensitivities on endospores of Bacillus pumilus and B. cereus at polished rice, whole black pepper and glass fiber filter dried with additives of 2% peptone + 1% glycerin were almost equivalent, and D{sub 10} values of gamma-rays were obtained to be 1.8 - 2.2 kGy for B. pumilus and 1.2 - 1.3 kGy for B. cereus, respectively. However, D{sub 10} value was decreased to 1.6 kGy for B. pumilus and 1.0 kGy for B. cereus in white pepper powder, and increased significantly as 2.6 kGy for B. pumilus and 1.8 kGy for B. cereus in senna herb powder. In the case of B. megaterium, Enterobacter cloacae and Escherichia coli, D{sub 10} values were increased at all of food materials even in white pepper powder compared with glass fiber filter with additives. These results are indicating that glycerin and related radical scavengers in food components protect the bacteria such as B. megaterium, Ent. cloacae and E. coli more significantly from effects of radiation than B. pumilus or B. cereus. The increase of radiation resistance of these bacteria should be responsible also to the amount of oxygen penetration in bacterial cells which dried at different conditions. On the irradiation of electron-beams, radiation resistance of all of bacteria increased more significantly than gamma-rays which depending to dose rate effects on bacteria. However, increase of radiation resistance was not observed at Aspergillus oryzae in all of food materials at different dry conditions. (author)

  20. Functional Muscular Condition Dynamics at Osteoarthrosis Conservative Treatment of Major Joints of Lower Extremities

    Directory of Open Access Journals (Sweden)

    М.S. Sayfutdinov

    2009-06-01

    Full Text Available The method of global electromyography has been used for the evaluation of 231 patients aged from 16 to 74 (43,7±0,8 with bilateral osteoarthrosis of major joints of lower extremities I-III degrees before the course of conservative treatment, immediately after the end of conservative treatment and in three months. Conservative treatment of patients with osteoarthrosis of major joints of lower extremities has been shown to cause restructuring of EMG patterns of maximal voluntary muscle contraction in lower extremities accompanied by decreased asymmetry of activity levels in muscle pairs and less observations of pathologically changed EMG that results in improved functional condition of the locomotor system.

  1. Size-dependent chemical ageing of oleic acid aerosol under dry and humidified conditions

    Science.gov (United States)

    Al-Kindi, Suad S.; Pope, Francis D.; Beddows, David C.; Bloss, William J.; Harrison, Roy M.

    2016-12-01

    A chemical reaction chamber system has been developed for the processing of oleic acid aerosol particles with ozone under two relative humidity conditions: dry and humidified to 65 %. The apparatus consists of an aerosol flow tube, in which the ozonolysis occurs, coupled to a scanning mobility particle sizer (SMPS) and an aerosol time-of-flight mass spectrometer (ATOFMS) which measure the evolving particle size and composition. Under both relative humidity conditions, ozonolysis results in a significant decrease in particle size and mass which is consistent with the formation of volatile products that partition from the particle to the gas phase. Mass spectra derived from the ATOFMS reveal the presence of the typically observed reaction products: azelaic acid, nonanal, oxononanoic acid and nonanoic acid, as well as a range of higher molecular weight products deriving from the reactions of reaction intermediates with oleic acid and its oxidation products. These include octanoic acid and 9- and 10-oxooctadecanoic acid, as well as products of considerably higher molecular weight. Quantitative evaluation of product yields with the ATOFMS shows a marked dependence upon both particle size association (from 0.3 to 2.1 µm diameter) and relative humidity. Under both relative humidity conditions, the percentage residual of oleic acid increases with increasing particle size and the main lower molecular weight products are nonanal and oxononanoic acid. Under dry conditions, the percentage of higher molecular weight products increases with increasing particle size due to the poorer internal mixing of the larger particles. Under humidified conditions, the percentage of unreacted oleic acid is greater, except in the smallest particle fraction, with little formation of high molecular weight products relative to the dry particles. It is postulated that water reacts with reactive intermediates, competing with the processes which produce high molecular weight products. Whilst the

  2. Influence of spray drying operating conditions on microencapsulated rosemary essential oil properties

    Directory of Open Access Journals (Sweden)

    Regiane Victória de Barros Fernandes

    2013-02-01

    Full Text Available Spray drying is an important method used by the food industry in the production of microencapsulated flavors to improve handling and dispersion properties. The objective of this study was to evaluate the influence of the process conditions on the properties of rosemary essential oil microencapsulated by spray drying using gum Arabic as encapsulant. The effects of the wall material concentration (10-30%, inlet air temperature (135-195 ºC, and feed flow rate (0.5-1.0 L.h-1 on the moisture content, hygroscopicity, wettability, solubility, bulk and tapped densities, particle density, flowability, and cohesiveness were evaluated using a 2³ central composite rotational experimental design. Moisture content, hygroscopicity and wettability were significantly affected by the three factors analyzed. Bulk density was positively influenced by the wall material concentration and negatively by the inlet air temperature. Particle density was influenced by the wall material concentration and the inlet air temperature variables, both in a negative manner. As for the solubility, tapped density, flowability, and cohesiveness, the models did not fit the data well. The results indicated that moderate wall material concentration (24%, low inlet air temperature (135 ºC, and moderate feed flow rate (0.7 L.h-1 are the best spray drying conditions.

  3. Photolysis of tembotrione and its main by-products under extreme artificial conditions:

    Energy Technology Data Exchange (ETDEWEB)

    Calvayrac, Christophe; Bontemps, Nataly [Laboratoire de Chimie des Biomolécules et de l' Environnement (LCBE, EA 4215), Université de Perpignan Via Domitia (UPVD), 52 avenue Paul Alduy, 66860 Perpignan (France); Nouga-Bissoue, Achille [Ecole Nationale Supérieure de l' Enseignement Technique (ENSET), Université de Douala, BP 2701 Douala (Cameroon); Romdhane, Sana; Coste, Camille-Michel [Laboratoire de Chimie des Biomolécules et de l' Environnement (LCBE, EA 4215), Université de Perpignan Via Domitia (UPVD), 52 avenue Paul Alduy, 66860 Perpignan (France); Cooper, Jean-Francois, E-mail: cooper@univ-perp.fr [Laboratoire de Chimie des Biomolécules et de l' Environnement (LCBE, EA 4215), Université de Perpignan Via Domitia (UPVD), 52 avenue Paul Alduy, 66860 Perpignan (France)

    2013-05-01

    The photolytic behaviour of tembotrione, a new chemical herbicide intended for foliar application in corn, was investigated under unnatural and extreme photochemical exposure in aqueous solutions in the laboratory. It appeared that degradation was dependent on pH and occurred more rapidly under acidic and neutral conditions, leading predominantly to the formation of a xanthenedione type compound by intramolecular cyclisation with loss of HCl. Trace amounts of benzoic acid by-products appeared also during UV-C irradiation (λ = 254 nm) of the parent compound. Results were comparable to those obtained with sulcotrione, another β-triketone herbicide. These extreme irradiation conditions clearly accelerated the phototransformation of sulcotrione vs. simulated sunlight irradiation. Furthermore, the photolysis of the degradation by-products, resulting from either photolysis, hydrolysis or biotic pathways of the two active ingredients, was also carried out. The benzoic acid by-products appeared more stable to photolysis than their parent molecules. Xanthenedione derivatives were degraded more rapidly with several differences depending on the pH value. - Highlights: • Tembotrione and sulcotrione water photolysis appeared enhanced under unnatural and extreme conditions. • Triketones were easily photodegraded under acidic and neutral conditions. • Xanthenedione derivatives were the predominant by-products. • Phototransformation of xanthenedione derivatives was pH-dependent. • Benzoic acid derivatives can be relatively stable.

  4. Spatial and temporal mapping of water content across Nafion membranes under wetting and drying conditions.

    Science.gov (United States)

    Zhang, Ziheng; Marble, Andrew E; MacMillan, Bryce; Promislow, Keith; Martin, Jonathan; Wang, Haijiang; Balcom, Bruce J

    2008-10-01

    Water transport and water management are fundamental to polymer electrolyte membrane fuel cell operation. Accurate measurements of water content within and across the Nafion layer are required to elucidate water transport behavior and validate existing numerical models. We report here a direct measurement of water content profiles across a Nafion layer under wetting and drying conditions, using a novel magnetic resonance imaging methodology developed for this purpose. This method, multi-echo double half k-space spin echo single point imaging, based on a pure phase encode spin echo, is designed for high resolution 1D depth imaging of thin film samples. The method generates high resolution (drying, in addition to the steady state.

  5. Formation and Characterization of TiO2/CNT Nanomaterials Dried under Supergravity Conditions

    Directory of Open Access Journals (Sweden)

    Minerva Vargas

    2009-01-01

    Full Text Available The elaboration of bilayer TiO2/CNT films dried under terrestrial gravity conditions (g and on a centrifuge with 1.3g and 7g is reported. The changes in microstructure and thickness of these coatings under supergravity environment cause a red-shift tendency in the optical properties at increasing values of acceleration. Experiments of a drop under enhanced gravity force in the range of 3.7 < Bo (bond number < 51.5 suggest the incomplete elimination of surfactant-water molecules in the TiO2/CNT bilayer film. Increasing acceleration up to 14g will widen the optical differences found, proving the layer-by-layer solution-chemical method in combination with these drying protocols, an alternative to produce thickness-sensitive solar-selective absorbing coatings.

  6. Inelastic X-ray scattering experiments at extreme conditions: high temperatures and high pressures

    Directory of Open Access Journals (Sweden)

    S.Hosokawa

    2008-03-01

    Full Text Available In this article, we review the present status of experimental techniques under extreme conditions of high temperature and high pressure used for inelastic X-ray scattering (IXS experiments of liquid metals, semiconductors, molten salts, molecular liquids, and supercritical water and methanol. For high temperature experiments, some types of single-crystal sapphire cells were designed depending on the temperature of interest and the sample thickness for the X-ray transmission. Single-crystal diamond X-ray windows attached to the externally heated high-pressure vessel were used for the IXS experiment of supercritical water and methanol. Some typical experimental results are also given, and the perspective of IXS technique under extreme conditions is discussed.

  7. Proceedings of the third symposium on science of hadrons under extreme conditions

    Energy Technology Data Exchange (ETDEWEB)

    Chiba, Satoshi (ed.) [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

    2001-09-01

    The third symposium on Science of Hadrons under Extreme Conditions, organized by the Research Group for Hadron Science, Advanced Science Research Center, was held at Tokai Research Establishment of JAERI on January 29 to 31, 2001. The symposium was devoted for discussions and presentations of research results in wide variety of hadron physics such as nuclear matter, high-energy nuclear reactions, quantum chromodynamics, neutron stars, supernovae, nucleosynthesis as well as finite nuclei to understand various aspects of hadrons under extreme conditions. Twenty two papers on these topics presented at the symposium, including a special talk on the present status of JAERI-KEK joint project on high-intensity proton accelerator, aroused lively discussions among approximately 40 participants. The 20 of the presented papers are indexed individually. (J.P.N.)

  8. Improvised purification methods for obtaining individual drinking water supply under war and extreme shortage conditions.

    Science.gov (United States)

    Kozlicic, A; Hadzic, A; Bevanda, H

    1994-01-01

    Supplying an adequate amount of drinking water to a population is a complex problem that becomes an extremely difficult task in war conditions. In this paper, several simple methods for obtaining individual supplies of drinking water by filtration of atmospheric water with common household items are reported. Samples of atmospheric water (rain and snow) were collected, filtered, and analyzed for bacteriological and chemical content. The ability of commonly available household materials (newspaper, filter paper, gauze, cotton, and white cotton cloth) to filter water from the environmental sources was compared. According to chemical and biological analysis, the best results were obtained by filtering melted snow from the ground through white cotton cloth. Atmospheric water collected during war or in extreme shortage conditions can be purified with simple improvised filtering techniques and, if chlorinated, used as an emergency potable water source.

  9. The limits of the adaptation of life to extreme conditions (in connection with problems of exobiology)

    Science.gov (United States)

    Aksenov, S. I.

    1973-01-01

    Accommodation is discussed as a universal evolutionary principle which essentially will apply to all life forms, regardless of chemical base (carbon, silicon, etc.). Life forms must either adapt to extreme conditions or perish, and for any life form an extremum factor is any significant deviation in environmental parameters. The possibility of life forms existing in specific extraterrestrial environments is discussed, and a conclusion is drawn which unequivocally states that through many forms of accommodation life is possible in many different environments.

  10. Life at extreme conditions: Neutron scattering studies of biological molecules suggest that evolution selected dynamics

    Indian Academy of Sciences (India)

    Joseph (Giuseppe) Zaccai

    2008-10-01

    The short review concentrates on recent work performed at the neutrons in biology laboratories of the Institut Laue Langevin and Institut de Biologie Structurale in Grenoble. Extremophile organisms have been discovered that require extreme conditions of temperature, pressure or solvent environment for survival. The existence of such organisms poses a significant challenge in understanding the physical chemistry of their proteins, in view of the great sensitivity of protein structure and stability to the aqueous environment and to external conditions in general. Results of neutron scattering measurements on the dynamics of proteins from extremophile organisms, in vitro as well as in vivo, indicated remarkably how adaptation to extreme conditions involves forces and fluctuation amplitudes that have been selected specifically, suggesting that evolutionary macromolecular selection proceeded via dynamics. The experiments were performed on a halophilic protein, and membrane adapted to high salt, a thermophilic enzyme adapted to high temperature and its mesophilic (adapted to 37°C) homologue; and in vivo for psychrophilic, mesophilic, thermophilic and hyperthermophilic bacteria, adapted respectively to temperatures of 4°C, 37°C, 75°C and 85°C. Further work demonstrated the existence of a water component of exceptionally low mobility in an extreme halophile from the Dead Sea, which is not present in mesophile bacterial cells.

  11. Water Use Efficiency and Physiological Response of Rice Cultivars under Alternate Wetting and Drying Conditions

    Directory of Open Access Journals (Sweden)

    Yunbo Zhang

    2012-01-01

    Full Text Available One of the technology options that can help farmers cope with water scarcity at the field level is alternate wetting and drying (AWD. Limited information is available on the varietal responses to nitrogen, AWD, and their interactions. Field experiments were conducted at the International Rice Research Institute (IRRI farm in 2009 dry season (DS, 2009 wet season (WS, and 2010 DS to determine genotypic responses and water use efficiency of rice under two N rates and two water management treatments. Grain yield was not significantly different between AWD and continuous flooding (CF across the three seasons. Interactive effects among variety, water management, and N rate were not significant. The high yield was attributed to the significantly higher grain weight, which in turn was due to slower grain filling and high leaf N at the later stage of grain filling of CF. AWD treatments accelerated the grain filling rate, shortened grain filling period, and enhanced whole plant senescence. Under normal dry-season conditions, such as 2010 DS, AWD reduced water input by 24.5% than CF; however, it decreased grain yield by 6.9% due to accelerated leaf senescence. The study indicates that proper water management greatly contributes to grain yield in the late stage of grain filling, and it is critical for safe AWD technology.

  12. Static friction of biomimetic surface microstructure of PDMS under wet and dry conditions

    Science.gov (United States)

    Yu, Haiwu; Jia, Hongduo; Gong, Ling; Li, Rong; Wang, Caiping; Wang, Xiaojie

    2016-04-01

    Smooth adhesive pad found among arthropods, amphibians, particularly tree frogs, are usually covered with surface microstructure of different shape to enhance the attachment abilities on the smooth substrate. During the last decade, it has gained more attentions in the development of anti-slippery systems by mimicking these unique characteristics. In this paper, we studied a new amphibian species newt by observing their climbing abilities on wet and dry vertical smooth surface, and found that the newts can even hang on the surface with an inclination angle more than 90° without falling. We investigated the toe pad micro-structured surface of the newt by using scanning electron microscopy (SEM), and found that an array of hexagonal cells with micro-ridges on cell borders exists for the larvae; while an array of hexagonal cells separated by microgrooves is for the adult. Inspired by these features, the biomimetic micro-structured surfaces were fabricated using a soft elastomeric material polydimethysiloxane (PDMS). Four different microstructures were chosen to study their tribological properties with a solid substrate under wet and dry conditions. The patterns of the microstructures include round pillar, hexagonal pillar, round pillars surrounded by a closed hexagonal ridge, and round pillars surrounded by a semi-closed hexagonal ridge. The static friction tests were carried out using the multi-functional surface meter TYPE12. The results showed that the area ratio of the micro pillar plays a major role in enhancing the static friction for both wet and dry conditions, while the numerical density of the micro pillar has less effect on the friction enhancement. Among the four kind specimens, the specimen with hexagonal pillars would increase the static friction more than others at the same test conditions when the pillar area ratio is lower than 40%.

  13. [Hygienic problems of population health maintenance under the extremal conditions of North].

    Science.gov (United States)

    Potapov, A I; Istomin, A V; Shushkova, T S; Ustiushin, B V; Iudina, T V; Maĭmulov, V G; Raengulov, B M; Shagdarova, A N

    2005-01-01

    A range of multi-sided studies, carried out in various regions of Far North (Jamalo-Nenets autonomous region, Komi republic, Sakha republic (Yakutia)) have established the leading hygienic risk factors of population health deterioration, including those characteristic of small nationalities of North. The consideration of the obtained data, including regional alimentary status peculiarities, the condition of metabolic processes and antioxidant balance of the organism, allowed establishment of effective approaches to the maintenance of notherners' health. These approaches are based upon the optimization of nutrition as an element of population health control under extremal conditions.

  14. Adhesion energy between mica surfaces: Implications for the frictional coefficient under dry and wet conditions

    Science.gov (United States)

    Sakuma, Hiroshi

    2013-12-01

    frictional strength of faults is a critical factor that contributes to continuous fault slip and earthquake occurrence. Frictional strength can be reduced by the presence of sheet-structured clay minerals. In this study, two important factors influencing the frictional coefficient of minerals were quantitatively analyzed by a newly developed computational method based on a combination of first-principles study and thermodynamics. One factor that helps reduce the frictional coefficient is the low adhesion energy between the layers under dry conditions. Potassium ions on mica surfaces are easily exchanged with sodium ions when brought into contact with highly concentrated sodium-halide solutions. We found that the surface ion exchange with sodium ions reduces the adhesion energy, indicating that the frictional coefficient can be reduced under dry conditions. Another factor is the lubrication caused by adsorbed water films on mineral surfaces under wet conditions. Potassium and sodium ions on mica surfaces have a strong affinity for water molecules. In order to remove the adsorbed water molecules confined between mica surfaces, a differential compressive stress of the order of tens of gigapascals was necessary at room temperature. These water molecules inhibit direct contact between mineral surfaces and reduce the frictional coefficient. Our results imply that the frictional coefficient can be modified through contact with fluids depending on their salt composition. The low adhesion energy between fault-forming minerals and the presence of an adsorbed water film is a possible reason for the low frictional coefficient observed at continuous fault slip zones.

  15. Role of PET in improving wear properties of PP in dry sliding condition

    Indian Academy of Sciences (India)

    Somit Neogi; S A R Hashmi; Navin Chand

    2003-10-01

    The sliding wear of isotactic polypropylene (PP), polyethylene terephthalate (PET) and their blends was evaluated as a function of applied pressure and composition against a stainless steel counter face in dry condition. Wear rate decreases with the addition of PET in the blend. The wear was observed in two stages, the moderate wear and high wear while increasing the applied pressure on test samples. The addition of PET in PP helps in increasing the limit of moderate wear towards the high-pressure side. Microstructure and worn surfaces of samples were observed by scanning electron microscope. The wear phenomenon has been discussed based on wear losses and worn surfaces.

  16. Performance of some sunflower genotypes grown under dry weather conditions in south Bulgaria

    Directory of Open Access Journals (Sweden)

    Nurettin Tahsin

    2015-09-01

    Full Text Available Information on yield and agricultural performance of new sunflower (Helianthus annuus L. hybrids grown under dry weather conditions in South Bulgaria is limited. The objectives of this field study is to acquire information on seed yield and other agricultural characteristics of five sunflower hybrids and their parental lines in South Bulgaria. This research was carried out on the Experimental farm at the Agricultural University in Plovdiv, Bulgaria in the seasons of 2008 and 2009. Statistical analysis revealed that the differences among genotypes for all studied characters were significant in both seasons as well as in the combined one.

  17. Impact of different spray-drying conditions on the viability of wine Saccharomyces cerevisiae strains.

    Science.gov (United States)

    Aponte, Maria; Troianiello, Gabriele Danilo; Di Capua, Marika; Romano, Raffaele; Blaiotta, Giuseppe

    2016-01-01

    Spray-drying (SD) is widely considered a suitable method to preserve microorganisms, but data regarding yeasts are still scanty. In this study, the effect of growing media, process variables and carriers over viability of a wild wine Saccharomyces (S.) cerevisiae LM52 was evaluated. For biomass production, the strain was grown (batch and fed-batch fermentation) in a synthetic, as well as in a beet sugar molasses based-medium. Drying of cells resuspended in several combinations of soluble starch and maltose was performed at different inlet and outlet temperatures. Under the best conditions-suspension in soluble starch plus maltose couplet to inlet and outlet temperatures of 110 and 55 °C, respectively-the loss of viability of S. cerevisiae LM52 was 0.8 ± 0.1 and 0.5 ± 0.2 Log c.f.u. g(-1) for synthetic and molasses-based medium, respectively. Similar results were obtained when S. cerevisiae strains Zymoflore F15 and EC1118, isolated from commercial active dry yeast (ADY), were tested. Moreover, powders retained a high vitality and showed good fermentation performances up to 6 month of storage, at both 4 and -20 °C. Finally, fermentation performances of different kinds of dried formulates (SD and ADY) compared with fresh cultures did not show significant differences. The procedure proposed allowed a small-scale production of yeast in continuous operation with relatively simple equipment, and may thus represent a rapid response-on-demand for the production of autochthonous yeasts for local wine-making.

  18. Reduced CO2 fertilization effect in temperate C3 grasslands under more extreme weather conditions

    Science.gov (United States)

    Obermeier, W. A.; Lehnert, L. W.; Kammann, C. I.; Müller, C.; Grünhage, L.; Luterbacher, J.; Erbs, M.; Moser, G.; Seibert, R.; Yuan, N.; Bendix, J.

    2016-12-01

    The increase in atmospheric greenhouse gas concentrations from anthropogenic activities is the major driver of recent global climate change. The stimulation of plant photosynthesis due to rising atmospheric carbon dioxide concentrations ([CO2]) is widely assumed to increase the net primary productivity (NPP) of C3 plants--the CO2 fertilization effect (CFE). However, the magnitude and persistence of the CFE under future climates, including more frequent weather extremes, are controversial. Here we use data from 16 years of temperate grassland grown under `free-air carbon dioxide enrichment’ conditions to show that the CFE on above-ground biomass is strongest under local average environmental conditions. The observed CFE was reduced or disappeared under wetter, drier and/or hotter conditions when the forcing variable exceeded its intermediate regime. This is in contrast to predictions of an increased CO2 fertilization effect under drier and warmer conditions. Such extreme weather conditions are projected to occur more intensely and frequently under future climate scenarios. Consequently, current biogeochemical models might overestimate the future NPP sink capacity of temperate C3 grasslands and hence underestimate future atmospheric [CO2] increase.

  19. Reduced CO2 fertilization effect in temperate C3 grasslands under more extreme weather conditions

    Science.gov (United States)

    Obermeier, W. A.; Lehnert, L. W.; Kammann, C. I.; Müller, C.; Grünhage, L.; Luterbacher, J.; Erbs, M.; Moser, G.; Seibert, R.; Yuan, N.; Bendix, J.

    2017-02-01

    The increase in atmospheric greenhouse gas concentrations from anthropogenic activities is the major driver of recent global climate change. The stimulation of plant photosynthesis due to rising atmospheric carbon dioxide concentrations ([CO2]) is widely assumed to increase the net primary productivity (NPP) of C3 plants--the CO2 fertilization effect (CFE). However, the magnitude and persistence of the CFE under future climates, including more frequent weather extremes, are controversial. Here we use data from 16 years of temperate grassland grown under `free-air carbon dioxide enrichment’ conditions to show that the CFE on above-ground biomass is strongest under local average environmental conditions. The observed CFE was reduced or disappeared under wetter, drier and/or hotter conditions when the forcing variable exceeded its intermediate regime. This is in contrast to predictions of an increased CO2 fertilization effect under drier and warmer conditions. Such extreme weather conditions are projected to occur more intensely and frequently under future climate scenarios. Consequently, current biogeochemical models might overestimate the future NPP sink capacity of temperate C3 grasslands and hence underestimate future atmospheric [CO2] increase.

  20. Life under multiple extreme conditions: diversity and physiology of the halophilic alkalithermophiles.

    Science.gov (United States)

    Mesbah, Noha M; Wiegel, Juergen

    2012-06-01

    Around the world, there are numerous alkaline, hypersaline environments that are heated either geothermally or through intense solar radiation. It was once thought that such harsh environments were inhospitable and incapable of supporting a variety of life. However, numerous culture-dependent and -independent studies revealed the presence of an extensive diversity of aerobic and anaerobic bacteria and archaea that survive and grow under these multiple harsh conditions. This diversity includes the halophilic alkalithermophiles, a novel group of polyextremophiles that require for growth and proliferation the multiple extremes of high salinity, alkaline pH, and elevated temperature. Life under these conditions undoubtedly involves the development of unique physiological characteristics, phenotypic properties, and adaptive mechanisms that enable control of membrane permeability, control of intracellular osmotic balance, and stability of the cell wall, intracellular proteins, and other cellular constituents. This minireview highlights the ecology and growth characteristics of the extremely halophilic alkalithermophiles that have been isolated thus far. Biochemical, metabolic, and physiological properties of the extremely halophilic alkalithermophiles are described, and their roles in resistance to the combined stressors of high salinity, alkaline pH, and high temperature are discussed. The isolation of halophilic alkalithermophiles broadens the physicochemical boundaries for life and extends the boundaries for the combinations of the maximum salinity, pH, and temperature that can support microbial growth.

  1. The impact of extreme weather conditions on the life of settlers in the Central Russia in X - XVI centuries

    Science.gov (United States)

    Graves, Irina; Nizovtsev, Viacheslav; Erman, Natalia

    2017-04-01

    A special place in the reconstruction of climate dynamics takes an analysis of extraordinary meteorological phenomena. These extreme weather events in the first place impact the functioning of, the rhythm and dynamics of the landscapes and determine not only the features of economy, but also certain aspects of historical development. In the analysis of primary chronicles and published data, along with the direct climatic characteristics (hot, warm, cold, wet, dry, etc.) a lot of attention was paid to abnormal (extreme) natural phenomena and indirect indications of climate variability (floods, crop failures, hunger years, epidemics, etc.). As a result, tables were compiled reflecting climatic basic characteristics and extremes for each year since 900 BC. X-XI centuries was a period of minor climatic optimum - the climate was warmer and drier than the modern one. In addition to higher temperatures (up to 1-3C above than mordern), during this period there were no severe winters. A small amount of summer rainfall has led to a reduction in the number of small water reservoirs and flooding rivers. This is evidenced by Slavic settlements on floodplains of a number of rivers in the Moscow region. It is in this favorable climatic time the way "from the Vikings to the Greeks" was open. Catastrophic natural events had a minimum repeatability. For example, during the X century the Russian chronicles mentioned 41 extreme event, but for the XIII century - 102. Most of the villages and towns were located on the low floodplain terraces of rivers. The main farmland was concentrated there as well. In the "period of contrasts" (XIII - XIV centuries) there was an increase of intra-seasonal climate variability, humidity and widespread reduction in summer temperatures by 1-2C. The number of extreme weather events increased: cold prolonged winters, long rains in summers, cold weather returns in the early summer, early frosts in late summer - early autumn. Such conditions often

  2. Self-heating of dried industrial wastewater sludge: lab-scale investigation of supporting conditions.

    Science.gov (United States)

    Della Zassa, M; Biasin, A; Zerlottin, M; Refosco, D; Canu, P

    2013-06-01

    We studied the reactivity of dried sludge produced by treatment of wastewater, mainly from tanneries. The solids transformations have been first characterized with thermal analysis (TGA and DSC) proving that exothermic transformation takes place at fairly low temperature, before the total organic combustion that occurs in air above 400°C. The onset of low temperature reactions depends on the heating rate and it can be below 100°C at very small heating rate. Then, we reproducibly determined the conditions to trigger dried sludge self-heating at the laboratory scale, on samples in the 0.2-0.3 kg size. Thermal insulation, some aeration and addition of water are key factors. Mastering the self-heating at this scale allows more detailed investigations as well as manipulation of conditions, to understand its nature, course and remediation. Here we report proves and discussions on the role of air, water, particle size, porosity and biological activity, as well as proving that also dried sludge from similar sources lead to self-heating. Tests demonstrate that air and water are simultaneously required for significant self-heating to occur. They act in diverging directions, both triggering the onset of the reactions and damping the temperature rise, by supporting heat loss. The higher the O2 concentration, the higher the solids heating rate. More added water prolongs the exothermic phase. Further additions of water can reactivate the material. Water emphasizes the exothermic processes, but it is not sufficient to start it in an air-free atmosphere. The initial solid moisture concentration (between 8% and 15%) affects the onset of self-heating as intuitive. The sludge particles size strongly determines the strength and extent of the heat release, indicating that surface reactions are taking place. In pelletized particles, limitations to water and air permeability mitigates the reaction course.

  3. Influence of Superplasticizers on Strength and Shrinkage Cracking of Cement Mortar under Drying Conditions

    Institute of Scientific and Technical Information of China (English)

    MA Baoguo; WANG Xin'gang; LI Xiangguo; YANG Lei

    2007-01-01

    The effects of polynaphthalene series superplasticizers(PNS) with a low content of sodium sulfate (H-UNF),with a high content of sodium sulfate(C-UNF) and polycarboxylate type superplasticizer (PC) on strength and shrinkage cracking of cement mortar under drying conditions were investigated by means of multi-channel ellipse ring shrinkage cracking test, free shrinkage and strength test. The general effect of PNS and PC is to increase the initial cracking time of mortars, and decrease the cracking sensitivity of mortars. As for decreasing the cracking sensitivity of mortars, PC>H-UNF>C-UNF. To incorporate superplasticizers is apparently to increase the free shrinkage of mortars when keeping the constant w/b ratio and the content of cement pastes. As for the effect of controlling the volume stability of mortars, PC>C-UNF>H-UNF. Maximum crack width of mortars containing PC is lower, but the development rate of maximum crack width of mortars containing H-UNF is faster in comparison with control mortars. The flexural and compressive strengths of mortars at 28-day increase with increasing superplasticizer dosages under drying conditions. PC was superior to PNS in the aspect of increasing strength.

  4. Optimization of freeze drying conditions for purified pectinase from mango (Mangifera indica cv. Chokanan) peel.

    Science.gov (United States)

    Mehrnoush, Amid; Mustafa, Shuhaimi; Yazid, Abdul Manap Mohd

    2012-01-01

    Response surface methodology (RSM) along with central composite design (CCD) was applied to optimize the freeze drying conditions for purified pectinase from mango (Mangifera indica cv. Chokanan) peel. The effect of pectinase content (-2.66, 62.66 mg/mL), Arabic gum (-1.21, 10.21%, w/v), and maltodextrin (0.73, 7.26%, w/v) as independent variables on activity, yield, and storage stability of freeze-dried enzyme was evaluated. Storage stability of pectinase was investigated after one week at 4 °C and yield percentage of the enzyme after encapsulation was also determined. The independent variables had the most significant (p mango peel were obtained using 30 mg/mL of pectinase content, 4.5 (%, w/v) of Arabic gum, and 4 (%, w/v) of maltodextrin. Under these conditions, the maximum activity (11.12 U/mL), yield (86.4%) and storage stability (84.2%) of encapsulated pectinase were achieved.

  5. Persistence of dengue virus RNA in dried Aedes aegypti (Diptera: Culicidae) exposed to natural tropical conditions.

    Science.gov (United States)

    Bangs, Michael J; Pudiantari, Ratna; Gionar, Yoyo R

    2007-01-01

    Aedes aegypti (L.) is the primary vector of dengue viruses, a group of four serotypic single-stranded RNA viruses. Dengue virus RNA can be readily detected in fresh or dried infected mosquitoes by using reverse transcriptase-polymerase chain reaction (RT-PCR). The current study examined the persistence and limit of dengue virus RNA detection in infected Ae. aegypti killed and exposed to natural ambient tropical conditions of temperature and humidity. Under relatively harsh conditions, dengue RNA retained sufficient integrity to be detected in dried mosquitoes up to 13 wk after exposure to relatively high ambient temperatures (26.3-31.7 degrees C) and relative humidity (49.4-69.9%). These findings confirm that the necessity for testing either fresh or frozen mosquitoes is not a prerequisite when using RT-PCR as the viral detection method, and under particular epidemiological circumstances it allows for a more convenient means of conducting vector-virus surveillance activities where collection methods and logistics may preclude immediate testing or access to a cold chain.

  6. Transitional dispersive scenarios driven by mesoscale flows on complex terrain under strong dry convective conditions

    Directory of Open Access Journals (Sweden)

    J. L. Palau

    2009-01-01

    Full Text Available By experimentation and modelling, this paper analyses the atmospheric dispersion of the SO2 emissions from a power plant on complex terrain under strong convective conditions, describing the main dispersion features as an ensemble of "stationary dispersive scenarios" and reformulating some "classical" dispersive concepts to deal with the systematically monitored summer dispersive scenarios in inland Spain. The results and discussions presented arise from a statistically representative study of the physical processes associated with the multimodal distribution of pollutants aloft and around a 343-m-tall chimney under strong dry convective conditions in the Iberian Peninsula. This paper analyses the importance of the identification and physical implications of transitional periods for air quality applications. The indetermination of a transversal plume to the preferred transport direction during these transitional periods implies a small (or null physical significance of the classical definition of horizontal standard deviation of the concentration distribution.

  7. Onset of frictional sliding of rubber-glass contact under dry and lubricated conditions

    Science.gov (United States)

    Tuononen, Ari J.

    2016-06-01

    Rubber friction is critical in many applications ranging from automotive tyres to cylinder seals. The process where a static rubber sample transitions to frictional sliding is particularly poorly understood. The experimental and simulation results in this paper show a completely different detachment process from the static situation to sliding motion under dry and lubricated conditions. The results underline the contribution of the rubber bulk properties to the static friction force. In fact, simple Amontons’ law is sufficient as a local friction law to produce the correct detachment pattern when the rubber material and loading conditions are modelled properly. Simulations show that micro-sliding due to vertical loading can release initial shear stresses and lead to a high static/dynamic friction coefficient ratio, as observed in the measurements.

  8. The effect of rainfall and competition intensity on forest response to drought: lessons learned from a dry extreme.

    Science.gov (United States)

    Dorman, Michael; Perevolotsky, Avi; Sarris, Dimitrios; Svoray, Tal

    2015-04-01

    We investigated forest responses to global warming by observing: (1) planted Pinus halepensis forests, (2) an aridity gradient-with annual precipitation (P) ranging from ~300 to ~700 mm, and (3) periods of wet and dry climate that included the driest period during at least the last 110 years. We examined: (1) how the length of climatic integration periods to which trees are most responsive varies in space and time, (2) the extent to which competition modulates growth decline during drought (2011) and subsequent recovery (2012) years. The temporal scale of rainfall that was most influential on growth shortened in progressing southward, and in the drier than in the wetter period. Long-term underground water storage, as reflected in the relationship of growth to multiple-year rainfall, remained significant up to the point where P ≈ 500 mm. Under drier conditions (P Competition appeared to set an upper limit to growth, while growth variation among individual trees increased as competition-intensity decreased. That upper limit increased in 2012 compared with 2011. The observed insensitivity of slow-growing trees to competition implies that mortality risk may be density independent, when even any potential for higher soil moisture availability in open stands is lost to evapotranspiration before it can benefit tree growth.

  9. Some traits of low temperature germplasm wheat under extremely unfavorable weather conditions

    Institute of Scientific and Technical Information of China (English)

    张嵩午; 王长发; 冯佰利; 苗芳; 周春菊; 张荣萍

    2001-01-01

    Through a long-term observation on the canopy temperature and some traits of wheat the temperature germplasm of wheat was found to result in the wheats having either a high or a low plant temperature. Under normal weather conditions, the wheat having a low temperature germplasm (LTG) demonstrated several advantageous physiologi-cal and agronomic traits than those having a high temperature germplasm (HTG). Under the extremely unfavorableweather conditions, such as rainy weather or severe drought, LTG wheat still could maintain its superiority to HTG wheat in physiological and agronomic traits including leaf functional duration, chlorophyll content, malondialdehyde content, transpiration rate, net photosynthesis rate, root vitality and kernel plumpness. The wide adaptability of LTG wheat to awide range of meteoro-ecological conditions could provide a valuable germplasm in breeding of good strains with broad-spectrum stress resistance.

  10. The myoglobin of Emperor penguin (Aptenodytes forsteri): amino acid sequence and functional adaptation to extreme conditions.

    Science.gov (United States)

    Tamburrini, M; Romano, M; Giardina, B; di Prisco, G

    1999-02-01

    In the framework of a study on molecular adaptations of the oxygen-transport and storage systems to extreme conditions in Antarctic marine organisms, we have investigated the structure/function relationship in Emperor penguin (Aptenodytes forsteri) myoglobin, in search of correlation with the bird life style. In contrast with previous reports, the revised amino acid sequence contains one additional residue and 15 differences. The oxygen-binding parameters seem well adapted to the diving behaviour of the penguin and to the environmental conditions of the Antarctic habitat. Addition of lactate has no major effect on myoglobin oxygenation over a large temperature range. Therefore, metabolic acidosis does not impair myoglobin function under conditions of prolonged physical effort, such as diving.

  11. 21st century increases in the likelihood of extreme hydrologic conditions for the mountainous basins of the Southwestern United States

    Science.gov (United States)

    Stewart, Iris T.; Ficklin, Darren L.; Carrillo, Carlos A.; McIntosh, Russell

    2015-10-01

    Extreme hydrologic conditions, such as floods, droughts, and elevated stream temperatures, significantly impact the societal fabric and ecosystems, and there is rising concern about increases in the frequency of extreme conditions with projected climate changes. Here we ask what changes in the occurrence of extreme hydrologic conditions can be expected by the end of the century for the important water-generating, mountainous basins of the Southwestern United States, namely the Sierra Nevada and Upper Colorado River Basins. The extreme conditions considered are very high flows, low flows, and elevated stream temperature as derived from historic and future simulations using the Soil and Water Assessment Tool (SWAT) hydrologic model and downscaled output from a General Circulation Model ensemble. Results indicate noteworthy differences in the frequency changes of extremes based on geographic region, season, elevation, and stream size. We found wide-spread increases in the occurrence of stream flows exceeding 150% of historic monthly averages for winter by the end of the century, and extensive increases in the occurrence of both extreme low flows (representing 3 °C of monthly averages) during the summer months, with some basins expecting extreme conditions 90-100% of the time by the end of the century. Understanding the differences in the changes of extreme conditions can identify climate-sensitive regions and assist in targeted planning for climate change adaptation and mitigation.

  12. Normal and Extreme Wind Conditions for Power at Coastal Locations in China.

    Science.gov (United States)

    Gao, Meng; Ning, Jicai; Wu, Xiaoqing

    2015-01-01

    In this paper, the normal and extreme wind conditions for power at 12 coastal locations along China's coastline were investigated. For this purpose, the daily meteorological data measured at the standard 10-m height above ground for periods of 40-62 years are statistically analyzed. The East Asian Monsoon that affects almost China's entire coastal region is considered as the leading factor determining wind energy resources. For most stations, the mean wind speed is higher in winter and lower in summer. Meanwhile, the wind direction analysis indicates that the prevalent winds in summer are southerly, while those in winter are northerly. The air densities at different coastal locations differ significantly, resulting in the difference in wind power density. The Weibull and lognormal distributions are applied to fit the yearly wind speeds. The lognormal distribution performs better than the Weibull distribution at 8 coastal stations according to two judgement criteria, the Kolmogorov-Smirnov test and absolute error (AE). Regarding the annual maximum extreme wind speed, the generalized extreme value (GEV) distribution performs better than the commonly-used Gumbel distribution. At these southeastern coastal locations, strong winds usually occur in typhoon season. These 4 coastal provinces, that is, Guangdong, Fujian, Hainan, and Zhejiang, which have abundant wind resources, are also prone to typhoon disasters.

  13. Normal and Extreme Wind Conditions for Power at Coastal Locations in China.

    Directory of Open Access Journals (Sweden)

    Meng Gao

    Full Text Available In this paper, the normal and extreme wind conditions for power at 12 coastal locations along China's coastline were investigated. For this purpose, the daily meteorological data measured at the standard 10-m height above ground for periods of 40-62 years are statistically analyzed. The East Asian Monsoon that affects almost China's entire coastal region is considered as the leading factor determining wind energy resources. For most stations, the mean wind speed is higher in winter and lower in summer. Meanwhile, the wind direction analysis indicates that the prevalent winds in summer are southerly, while those in winter are northerly. The air densities at different coastal locations differ significantly, resulting in the difference in wind power density. The Weibull and lognormal distributions are applied to fit the yearly wind speeds. The lognormal distribution performs better than the Weibull distribution at 8 coastal stations according to two judgement criteria, the Kolmogorov-Smirnov test and absolute error (AE. Regarding the annual maximum extreme wind speed, the generalized extreme value (GEV distribution performs better than the commonly-used Gumbel distribution. At these southeastern coastal locations, strong winds usually occur in typhoon season. These 4 coastal provinces, that is, Guangdong, Fujian, Hainan, and Zhejiang, which have abundant wind resources, are also prone to typhoon disasters.

  14. Meibomian gland dysfunction determines the severity of the dry eye conditions in visual display terminal workers.

    Directory of Open Access Journals (Sweden)

    Huping Wu

    Full Text Available OBJECTIVE: To explore meibomian gland dysfunction (MGD may determine the severity of dry eye conditions in visual display terminal (VDT workers. METHODOLOGY: Prospective, case-control study carried out in China.106 eyes of 53 patients (VDT work time >4 hour per day were recruited as the Long time VDT group; 80 eyes of 40 control subjects (VDT work time ≤ 4 hour per day served as the Short time VDT group. A questionnaire of Ocular Surface Disease Index (OSDI and multiple tests were performed. Three dry eye tests: tear film breakup time (BUT, corneal fluorescein staining, Schirmer I test; and three MGD parameters: lid margin abnormality score, meibum expression assessment (meibum score, and meibomian gland dropout degree (meiboscore using Keratograph 5 M. PRINCIPAL FINDINGS: OSDI and corneal fluorescein score were significantly higher while BUT was dramatically shorter in the long time VDT group than the short time VDT group. However, the average of Schirmer tear volumes was in normal ranges in both groups. Interestingly, the three MGD parameters were significantly higher in the long time VDT group than the short time one (P<0.0001. When 52 eyes with Schirmer <10 mm and 54 eyes with Schirmer ≥ 10 mm were separated from the long time VDT workers, no significant differences were found between the two subgroups in OSDI, fluorescein staining and BUT, as well as the three MGD parameters. All three MGD parameters were positively correlated with VDT working time (P<0.0001 and fluorescein scores (P<0.0001, inversely correlated with BUT (P<0.05, but not correlated with Schirmer tear volumes in the VDT workers. CONCLUSIONS: Our findings suggest that a malfunction of meibomian glands is associated with dry eye patients in long term VDT workers with higher OSDI scores whereas some of those patients presenting a normal tear volume.

  15. The Phase-Contrast Imaging Instrument at the Matter in Extreme Conditions Endstation at LCLS

    CERN Document Server

    Nagler, Bob; Galtier, Eric C; Arnold, Brice; Brown, Shaughnessy B; Fry, Alan; Gleason, Arianna; Granados, Eduardo; Hashim, Akel; Hastings, Jerome B; Samberg, Dirk; Seiboth, Frank; Tavella, Franz; Xing, Zhou; Lee, Hae Ja; Schroer, Christian G

    2016-01-01

    We describe the Phase-Contrast Imaging instrument at the Matter in Extreme Conditions (MEC) endstation of the Linac Coherent Light Source. The instrument can image phenomena with a spatial resolution of a few hundreds of nanometers and at the same time reveal the atomic structure through X-ray diffraction, with a temporal resolution better than 100 femtosecond. It was specifically designed for studies relevant to High-Energy-Density Science and can monitor, e.g., shock fronts, phase transitions, or void collapses. This versatile instrument was commissioned last year and is now available to the MEC user community.

  16. A statistical methodology for the estimation of extreme wave conditions for offshore renewable applications

    DEFF Research Database (Denmark)

    Larsén, Xiaoli Guo; Kalogeri, Christina; Galanis, George

    2015-01-01

    Rev, which is located in the North Sea, west of Denmark. The post-processing targets at correcting the modeled time series of the significant wave height, in order to match the statistics of the corresponding measurements, including not only the conventional parameters such as the mean and standard...... as a characteristic index of extreme wave conditions. The results from the proposed methodology seem to be in a good agreement with the measurements at both the relatively deep, open water and the shallow, coastal water sites, providing a potentially useful tool for offshore renewable energy applications. © 2015...

  17. Proceedings of the first symposium on science of hadrons under extreme conditions

    Energy Technology Data Exchange (ETDEWEB)

    Chiba, Satoshi; Maruyama, Toshiki [eds.

    1999-08-01

    The first symposium on Science of Hadrons under Extreme Conditions, organized by the Research Group for Hadron Science, Advanced Science Research Center, was held at Tokai Research Establishment of JAERI on March 11 and 12, 1999. The symposium was devoted for discussions and presentations of research results in wide variety of fields such as observation of X-ray pulsars, theoretical studies of nuclear matter, nuclear structure, low- and high-energy nuclear reactions and QCD. Thirty seven papers on these topics presented at the symposium are indexed individually. (J.P.N.)

  18. Inversion of Extremely Ill-Conditioned Matrices in Floating-Point

    OpenAIRE

    Rump, Siegfried M.

    2009-01-01

    Let an $n\\times n$ matrix $A$ of floating-point numbers in some format be given. Denote the relative rounding error unit of the given format by $\\mathtt{eps}$. Assume $A$ to be extremely ill-conditioned, that is $\\cond(A)\\gg\\mathtt{eps}^{-1}$. In about 1984 I developed an algorithm to calculate an approximate inverse of $A$ solely using the given floating-point format. The key is a multiplicative correction rather than a Newton-type additive correction. I did not publish it ...

  19. Probing the local, electronic and magnetic structure of matter under extreme conditions of temperature and pressure

    DEFF Research Database (Denmark)

    Torchio, R.; Boccato, S.; Cerantola, V.;

    2016-01-01

    In this paper we present recent achievements in the field of investigation of the local, electronic and magnetic structure of the matter under extreme conditions of pressure and temperature. These results were obtained thanks to the coupling of a compact laser heating system to the energy......-dispersive XAS technique available on the ID24 beamline at the ESRF synchrotron. The examples chosen concern the melting and the liquid structure of 3d metals and alloys under high pressures (HPs) and the observation of temperature-induced spin crossover in FeCO3 at HP....

  20. The effect of thermal processing condition on the physicochemical and sensory characteristics of fermented sausages dried by Quick-Dry-Slice process®.

    Science.gov (United States)

    Ferrini, G; Arnau, J; Guàrdia, M D; Comaposada, J

    2014-02-01

    The effect of different thermal processing conditions just after fermentation on physicochemical parameters and sensory attributes of salami and chorizo slices dried by Quick-Dry-Slice process®, was evaluated. Meat and common additives were mixed, stuffed and fermented. Previous to drying the sausages were subjected to thermal treatment at 53 °C at different exposure times (0, 50, 65, 80, 95 and 110 min). Finally, the sausages were sliced and dried using QDS process®. Color, instrumental texture and sensory analysis were performed. Lightness (L*) after fermentation increased with thermal processing in both products while redness (a*) and yellowness (b*) decreased only in salami. Thermal treatment after fermentation increased the initial force (F0). Cooked appearance, cooked fat odor, cooked flavor and stringiness increased when the thermal processing time was increased. Thermal processing of salami and chorizo at 53 °C for 50 min and drying up to 30% of weight loss resulted in a similar product to that obtained without thermal processing.

  1. A kinetic study of drying of TEOS-derived gels under nearly isothermal conditions

    Directory of Open Access Journals (Sweden)

    Donatti Dario A.

    1999-01-01

    Full Text Available The drying of wet Tetraethoxysilane-derived gels was studied by means of thermogravimetric analysis as a function of the time, from the instant when the samples were placed into a pre-heated oven, kept at 70, 83 and 100 °C. The precursor sol of the gel was obtained by sono-hydrolysis of the Tetraethoxysilane under acid condition and the final [Water]/[Tetraethoxysilane] molar ratio was adjusted to 30. The wet gels were cylindrical (2.5 cm height and 1.2 cm diameter after 30 days of aging at 30 °C in a hermetically sealed container. The changes in volume and weight during drying are compatible with a mechanism controlled by evaporation from a flat liquid-vapour interface at the surface of the body and contraction of the gel by capillary forces, together with structural changes induced by polycondensation, which partially account for the irreversible shrinkage of the gel. The employed thermogravimetric method does not permit to unequivocally follow the small and slow final loss of weight associated to the falling rate periods.

  2. Recent findings on the oxidation of UO{sub 2} fuel under nominally dry storage conditions

    Energy Technology Data Exchange (ETDEWEB)

    Taylor, P.; McEachern, R.J.; Sunder, S.; Wasywich, K.M.; Miller, N.H.; Wood, D.D

    1995-07-01

    This paper is an overview of fuel-storage demonstration experiments, supporting research on UO{sub 2} oxidation, and associated model development, in progress at AECL's Whiteshell Laboratories. The work is being performed to determine the time/temperature limits for safe storage of irradiated CANDU fuel in dry air. The most significant recent experimental finding has been the detection of small quantities of U{sub 3}O{sub 8}, formed over periods of one to several years in a variety of experiments at 150-170 deg C. Another important trading is the slight suppression of U{sub 3}O{sub 8} formation in SIMFUEL and other doped U0{sub 2} formulations. The development of a nucleation-and-growth model for U{sub 3}O{sub 8} formation is discussed, along with available activation energy data. These provide a basis for predicting U{sub 3}O{sub 8} formation rates under dry-storage conditions, and hence optimizing fuel storage strategies. (author)

  3. Thermo-mechanical Analysis of the Dry Clutches under Different Boundary Conditions

    Directory of Open Access Journals (Sweden)

    O.I. Abdullah

    2014-06-01

    Full Text Available The high thermal stresses, generated between the contacting surfaces of the clutch system (pressure plate, clutch disc and flywheel due to the frictional heating during the slipping, are considered to be one of the main reasons of clutch failure. A finite element technique has been used to study the transient thermoelastic phenomena of a dry clutch. The effect of the boundary conditions on the contact pressure distribution, the temperature field and the heat flux generated along the frictional surfaces are investigated. Analysis has been completed using two dimensional axisymmetric model that was used to simulate the clutch elements. ANSYS software has been used to perform the numerical calculation in this paper.

  4. Temperate heath plant response to dry conditions depends on growth strategy and less on physiology

    DEFF Research Database (Denmark)

    Albert, Kristian Rost; Kongstad, J.; Schmidt, I. K.

    2012-01-01

    The evidence that is currently available demonstrates that future changes in precipitation patterns will affect plant carbon uptake. However, the outcome in terms of success, productivity and fecundity depends upon individual species and different responses of various growth forms. Examination...... of these differences in response in dry versus rewetting conditions can be used to highlight the limitations coherent in different strategies adopted by, for example, evergreen shrubs and grasses. We investigated the leaf-level photosynthetic performance, leaf C, N and d13C along with vegetation cover and biomass...... rewetting increased leaf nitrogen and photosynthesis in the grass much more than for the dwarf shrub. These different strategies may have a considerable impact on carbon uptake and on the ability of a species to compete, as future climatic changes are likely to extend the summer drought period together...

  5. EFFECT OF CUTTING PARAMETERS ON SUPER ALLOY IN TURNING OPERATION UNDER DRY CONDITION

    Directory of Open Access Journals (Sweden)

    P.Marimuthu

    2014-12-01

    Full Text Available Ni-base super alloys are widely used in several industrial sectors, like petrochemical and power generation due to their high performance in aggressive environments. Inconel625 is primarily a Ni–Cr– Mo alloy used in different applications for its strength, excellent fabric ability and outstanding corrosion resistance. Machining of super alloy has been found to be a challenging task it has attracted considerable research. So, it is essential to know the cutting parameters for effective machining of super alloys. The present work focuses on finding the optimal cutting parameters for turning Inconel625 to achieve minimum surface roughness (SR, tool wear (TW and maximum material removal rate (MRR in CNC turning under dry conditions using TiAlN coated cutting tool. Single response optimization is performed by Taguchi method and multi response optimization is performed by desirability function analysis.

  6. Quantitative evaluation of the mitochondrial proteomes of Drosophila melanogaster adapted to extreme oxygen conditions.

    Science.gov (United States)

    Yin, Songyue; Xue, Jin; Sun, Haidan; Wen, Bo; Wang, Quanhui; Perkins, Guy; Zhao, Huiwen W; Ellisman, Mark H; Hsiao, Yu-hsin; Yin, Liang; Xie, Yingying; Hou, Guixue; Zi, Jin; Lin, Liang; Haddad, Gabriel G; Zhou, Dan; Liu, Siqi

    2013-01-01

    Mitochondria are the primary organelles that consume oxygen and provide energy for cellular activities. To investigate the mitochondrial mechanisms underlying adaptation to extreme oxygen conditions, we generated Drosophila strains that could survive in low- or high-oxygen environments (LOF or HOF, respectively), examined their mitochondria at the ultrastructural level via transmission electron microscopy, studied the activity of their respiratory chain complexes, and quantitatively analyzed the protein abundance responses of the mitochondrial proteomes using Isobaric tag for relative and absolute quantitation (iTRAQ). A total of 718 proteins were identified with high confidence, and 55 and 75 mitochondrial proteins displayed significant differences in abundance in LOF and HOF, respectively, compared with the control flies. Importantly, these differentially expressed mitochondrial proteins are primarily involved in respiration, calcium regulation, the oxidative response, and mitochondrial protein translation. A correlation analysis of the changes in the levels of the mRNAs corresponding to differentially regulated mitochondrial proteins revealed two sets of proteins with different modes of regulation (transcriptional vs. post-transcriptional) in both LOF and HOF. We believe that these findings will not only enhance our understanding of the mechanisms underlying adaptation to extreme oxygen conditions in Drosophila but also provide a clue in studying human disease induced by altered oxygen tension in tissues and cells.

  7. Quantitative evaluation of the mitochondrial proteomes of Drosophila melanogaster adapted to extreme oxygen conditions.

    Directory of Open Access Journals (Sweden)

    Songyue Yin

    Full Text Available Mitochondria are the primary organelles that consume oxygen and provide energy for cellular activities. To investigate the mitochondrial mechanisms underlying adaptation to extreme oxygen conditions, we generated Drosophila strains that could survive in low- or high-oxygen environments (LOF or HOF, respectively, examined their mitochondria at the ultrastructural level via transmission electron microscopy, studied the activity of their respiratory chain complexes, and quantitatively analyzed the protein abundance responses of the mitochondrial proteomes using Isobaric tag for relative and absolute quantitation (iTRAQ. A total of 718 proteins were identified with high confidence, and 55 and 75 mitochondrial proteins displayed significant differences in abundance in LOF and HOF, respectively, compared with the control flies. Importantly, these differentially expressed mitochondrial proteins are primarily involved in respiration, calcium regulation, the oxidative response, and mitochondrial protein translation. A correlation analysis of the changes in the levels of the mRNAs corresponding to differentially regulated mitochondrial proteins revealed two sets of proteins with different modes of regulation (transcriptional vs. post-transcriptional in both LOF and HOF. We believe that these findings will not only enhance our understanding of the mechanisms underlying adaptation to extreme oxygen conditions in Drosophila but also provide a clue in studying human disease induced by altered oxygen tension in tissues and cells.

  8. Extreme Wave-Induced Oscillation in Paradip Port Under the Resonance Conditions

    Science.gov (United States)

    Kumar, Prashant; Gulshan

    2017-08-01

    A mathematical model is constructed to analyze the long wave-induced oscillation in Paradip Port, Odisha, India under the resonance conditions to avert any extreme wave hazards. Boundary element method (BEM) with corner contribution is utilized to solve the Helmholtz equation under the partial reflection boundary conditions. Furthermore, convergence analysis is also performed for the boundary element scheme with uniform and non-uniform discretization of the boundary. The numerical scheme is also validated with analytic approximation and existing studies based on harbor resonance. Then, the amplification factor is estimated at six key record stations in the Paradip Port with multidirectional incident waves and resonance modes are also estimated at the boundary of the port. Ocean surface wave field is predicted in the interior of Paradip Port for the different directional incident wave at various resonance modes. Moreover, the safe locations in the port have been identified for loading and unloading of moored ship with different resonance modes and directional incident waves.

  9. Influence of Extreme Storage Conditions on Extra Virgin Olive Oil Parameters: Traceability Study

    Directory of Open Access Journals (Sweden)

    Alfredo Escudero

    2016-01-01

    Full Text Available This study reflects the effect of extreme storage conditions on several extra virgin olive oil (EVOO varieties (arbequina, hojiblanca, and picual. The conditions were simulated in the laboratory, by means of heating treatments in stove at different temperatures (40 and 60°C and times (two and three weeks. The aim is the evaluation of the deterioration of the quality parameters and minority components, which are responsible for the nutritional and therapeutic properties (fatty acids, polyphenols, pigments, and tocopherols, and organoleptic qualities. The quality criteria and limits used in this work are according to International Olive Council. The results contribute to the control of the traSceability for the commercialization of the EVOO.

  10. Influence of Extreme Storage Conditions on Extra Virgin Olive Oil Parameters: Traceability Study

    Science.gov (United States)

    Escudero, Alfredo; Pacheco, Rafael

    2016-01-01

    This study reflects the effect of extreme storage conditions on several extra virgin olive oil (EVOO) varieties (arbequina, hojiblanca, and picual). The conditions were simulated in the laboratory, by means of heating treatments in stove at different temperatures (40 and 60°C) and times (two and three weeks). The aim is the evaluation of the deterioration of the quality parameters and minority components, which are responsible for the nutritional and therapeutic properties (fatty acids, polyphenols, pigments, and tocopherols), and organoleptic qualities. The quality criteria and limits used in this work are according to International Olive Council. The results contribute to the control of the traSceability for the commercialization of the EVOO. PMID:28042493

  11. Variably-saturated flow in large weighing lysimeters under dry conditions: inverse and predictive modeling

    Science.gov (United States)

    Iden, Sascha; Reineke, Daniela; Koonce, Jeremy; Berli, Markus; Durner, Wolfgang

    2015-04-01

    A reliable quantification of the soil water balance in semi-arid regions requires an accurate determination of bare soil evaporation. Modeling of soil water movement in relatively dry soils and the quantitative prediction of evaporation rates and groundwater recharge pose considerable challenges in these regions. Actual evaporation from dry soil cannot be predicted without detailed knowledge of the complex interplay between liquid, vapor and heat flow and soil hydraulic properties exert a strong influence on evaporation rates during stage-two evaporation. We have analyzed data from the SEPHAS lysimeter facility in Boulder City (NV) which was installed to investigate the near-surface processes of water and energy exchange in desert environments. The scientific instrumentation consists of 152 sensors per Lysimeter which measured soil temperature, soil water content, and soil water potential. Data from three weighing lysimeters (3 m long, surface area 4 m2) were used to identifiy effective soil hydraulic properties of the disturbed soil monoliths by inverse modeling with the Richards equation assuming isothermal flow conditions. Results indicate that the observed soil water content in 8 different soil depths can be well matched for all three lysimeters and that the effective soil hydraulic properties of the three lysimeters agree well. These results could only be obtained with a flexible model of the soil hydraulic properties which guaranteed physical plausibility of water retention towards complete dryness and accounted for capillary, film and isothermal vapor flow. Conversely, flow models using traditional parameterizations of the soil hydraulic properties were not able to match the observed evaporation fluxes and water contents. After identifying the system properties by inverse modeling, we checked the possibility to forecast evaporation rates by running a fully coupled water, heat and vapor flow model which solved the energy balance of the soil surface. In these

  12. In Vitro Impact of Conditioned Medium From Demineralized Freeze-Dried Bone on Human Umbilical Endothelial Cells.

    Science.gov (United States)

    Harnik, Branko; Miron, Richard J; Buser, Daniel; Gruber, Reinhard

    2017-03-01

    Angiogenesis is essential for the consolidation of bone allografts. The underlying molecular mechanism, however, remains unclear. Soluble factors released from demineralized freeze-dried bone target mesenchymal cells; however, their effect on endothelial cells has not been investigated so far. The aim of the present study was therefore to examine the effect of conditioned medium from demineralized freeze-dried bone on human umbilical endothelial cells in vitro. Conditioned medium was first prepared from demineralized freeze-dried bone following 24 hours incubation at room temperature to produce demineralized bone conditioned media. Thereafter, conditioned medium was used to stimulate human umbilical vein endothelial cells in vitro by determining the cell response based on viability, proliferation, expression of apoptotic genes, a Boyden chamber to determine cell migration, and the formation of branches. The authors report here that conditioned medium decreased viability and proliferation of endothelial cells. Neither of the apoptotic marker genes was significantly altered when endothelial cells were exposed to conditioned medium. The Boyden chamber revealed that endothelial cells migrate toward conditioned medium. Moreover, conditioned medium moderately stimulated the formation of branches. These findings support the concept that conditioned medium from demineralized freeze-dried bone targets endothelial cells by decreasing their proliferation and enhancing their motility under these in vitro conditions.

  13. Concrete Condition Assessment Using Impact-Echo Method and Extreme Learning Machines

    Directory of Open Access Journals (Sweden)

    Jing-Kui Zhang

    2016-03-01

    Full Text Available The impact-echo (IE method is a popular non-destructive testing (NDT technique widely used for measuring the thickness of plate-like structures and for detecting certain defects inside concrete elements or structures. However, the IE method is not effective for full condition assessment (i.e., defect detection, defect diagnosis, defect sizing and location, because the simple frequency spectrum analysis involved in the existing IE method is not sufficient to capture the IE signal patterns associated with different conditions. In this paper, we attempt to enhance the IE technique and enable it for full condition assessment of concrete elements by introducing advanced machine learning techniques for performing comprehensive analysis and pattern recognition of IE signals. Specifically, we use wavelet decomposition for extracting signatures or features out of the raw IE signals and apply extreme learning machine, one of the recently developed machine learning techniques, as classification models for full condition assessment. To validate the capabilities of the proposed method, we build a number of specimens with various types, sizes, and locations of defects and perform IE testing on these specimens in a lab environment. Based on analysis of the collected IE signals using the proposed machine learning based IE method, we demonstrate that the proposed method is effective in performing full condition assessment of concrete elements or structures.

  14. Concrete Condition Assessment Using Impact-Echo Method and Extreme Learning Machines.

    Science.gov (United States)

    Zhang, Jing-Kui; Yan, Weizhong; Cui, De-Mi

    2016-03-26

    The impact-echo (IE) method is a popular non-destructive testing (NDT) technique widely used for measuring the thickness of plate-like structures and for detecting certain defects inside concrete elements or structures. However, the IE method is not effective for full condition assessment (i.e., defect detection, defect diagnosis, defect sizing and location), because the simple frequency spectrum analysis involved in the existing IE method is not sufficient to capture the IE signal patterns associated with different conditions. In this paper, we attempt to enhance the IE technique and enable it for full condition assessment of concrete elements by introducing advanced machine learning techniques for performing comprehensive analysis and pattern recognition of IE signals. Specifically, we use wavelet decomposition for extracting signatures or features out of the raw IE signals and apply extreme learning machine, one of the recently developed machine learning techniques, as classification models for full condition assessment. To validate the capabilities of the proposed method, we build a number of specimens with various types, sizes, and locations of defects and perform IE testing on these specimens in a lab environment. Based on analysis of the collected IE signals using the proposed machine learning based IE method, we demonstrate that the proposed method is effective in performing full condition assessment of concrete elements or structures.

  15. Experimental study on drying of typical MSW under incinerator-like conditions

    Institute of Scientific and Technical Information of China (English)

    ZHANG; YanGuo; CHEN; MeiQian; MENG; AiHong; LI; QingHai; CHEN; YunXuan

    2007-01-01

    In this paper, a series of experiments were conducted to investigate the drying of typical municipal solid wastes (MSW) in a muffle incinerator. From the experimental drying characteristic curves, the effects of temperature on drying process were observed to be more obvious in the low temperature region than in the high temperature region in muffle incinerator. At a specified drying temperature, drying time was highly dependent upon the packed waste thickness, having an exponent relation with the thickness. When the drying temperature increased or the thickness of potato bulks was diminished, the maximum drying rate reduced. Based on the first-order reaction, activation energy (Ea), and factor A of potato and cabbage were determined.

  16. Influenza transmission during extreme indoor conditions in a low-resource tropical setting

    Science.gov (United States)

    Tamerius, James; Ojeda, Sergio; Uejio, Christopher K.; Shaman, Jeffrey; Lopez, Brenda; Sanchez, Nery; Gordon, Aubree

    2017-04-01

    Influenza transmission occurs throughout the planet across wide-ranging environmental conditions. However, our understanding of the environmental factors mediating transmission is evaluated using outdoor environmental measurements, which may not be representative of the indoor conditions where influenza is transmitted. In this study, we examined the relationship between indoor environment and influenza transmission in a low-resource tropical population. We used a case-based ascertainment design to enroll 34 households with a suspected influenza case and then monitored households for influenza, while recording indoor temperature and humidity data in each household. We show that the indoor environment is not commensurate with outdoor conditions and that the relationship between indoor and outdoor conditions varies significantly across homes. We also show evidence of influenza transmission in extreme indoor environments. Specifically, our data suggests that indoor environments averaged 29 °C, 18 g/kg specific humidity, and 68 % relative humidity across 15 transmission events observed. These indoor settings also exhibited significant temporal variability with temperatures as high as 39 °C and specific and relative humidity increasing to 22 g/kg and 85 %, respectively, during some transmission events. However, we were unable to detect differences in the transmission efficiency by indoor temperature or humidity conditions. Overall, these results indicate that laboratory studies investigating influenza transmission and virus survival should increase the range of environmental conditions that they assess and that observational studies investigating the relationship between environment and influenza activity should use caution using outdoor environmental measurements since they can be imprecise estimates of the conditions that mediate transmission indoors.

  17. Influenza transmission during extreme indoor conditions in a low-resource tropical setting

    Science.gov (United States)

    Tamerius, James; Ojeda, Sergio; Uejio, Christopher K.; Shaman, Jeffrey; Lopez, Brenda; Sanchez, Nery; Gordon, Aubree

    2016-08-01

    Influenza transmission occurs throughout the planet across wide-ranging environmental conditions. However, our understanding of the environmental factors mediating transmission is evaluated using outdoor environmental measurements, which may not be representative of the indoor conditions where influenza is transmitted. In this study, we examined the relationship between indoor environment and influenza transmission in a low-resource tropical population. We used a case-based ascertainment design to enroll 34 households with a suspected influenza case and then monitored households for influenza, while recording indoor temperature and humidity data in each household. We show that the indoor environment is not commensurate with outdoor conditions and that the relationship between indoor and outdoor conditions varies significantly across homes. We also show evidence of influenza transmission in extreme indoor environments. Specifically, our data suggests that indoor environments averaged 29 °C, 18 g/kg specific humidity, and 68 % relative humidity across 15 transmission events observed. These indoor settings also exhibited significant temporal variability with temperatures as high as 39 °C and specific and relative humidity increasing to 22 g/kg and 85 %, respectively, during some transmission events. However, we were unable to detect differences in the transmission efficiency by indoor temperature or humidity conditions. Overall, these results indicate that laboratory studies investigating influenza transmission and virus survival should increase the range of environmental conditions that they assess and that observational studies investigating the relationship between environment and influenza activity should use caution using outdoor environmental measurements since they can be imprecise estimates of the conditions that mediate transmission indoors.

  18. The fate of carbon dioxide in water-rich fluids under extreme conditions

    Science.gov (United States)

    Pan, Ding; Galli, Giulia

    2016-01-01

    Investigating the fate of dissolved carbon dioxide under extreme conditions is critical to understanding the deep carbon cycle in Earth, a process that ultimately influences global climate change. We used first-principles molecular dynamics simulations to study carbonates and carbon dioxide dissolved in water at pressures (P) and temperatures (T) approximating the conditions of Earth’s upper mantle. Contrary to popular geochemical models assuming that molecular CO2(aq) is the major carbon species present in water under deep Earth conditions, we found that at 11 GPa and 1000 K, carbon exists almost entirely in the forms of solvated carbonate (CO32−) and bicarbonate (HCO3−) ions and that even carbonic acid [H2CO3(aq)] is more abundant than CO2(aq). Furthermore, our simulations revealed that ion pairing between Na+ and CO32−/HCO3− is greatly affected by P-T conditions, decreasing with increasing pressure at 800 to 1000 K. Our results suggest that in Earth’s upper mantle, water-rich geofluids transport a majority of carbon in the form of rapidly interconverting CO32− and HCO3− ions, not solvated CO2(aq) molecules. PMID:27757424

  19. The fate of carbon dioxide in water-rich fluids at extreme conditions

    CERN Document Server

    Pan, Ding

    2016-01-01

    Investigating the fate of dissolved carbon dioxide under extreme conditions is critical to understanding the deep carbon cycle in the Earth, a process that ultimately influences global climate change. We used first-principles molecular dynamics simulations to study carbonates and carbon dioxide dissolved in water at pressures (P) and temperatures (T) approximating the conditions of the Earth's upper mantle. Contrary to popular geochemical models assuming that molecular CO$_2$(aq) is the major carbon species present in water under deep earth conditions, we found that at 11 GPa and 1000 K carbon exists almost entirely in the forms of solvated carbonate (CO$_3^{2-}$) and bicarbonate (HCO$_3^-$) ions, and that even carbonic acid (H$_2$CO$_3$(aq)) is more abundant than CO$_2$(aq). Furthermore, our simulations revealed that ion pairing between Na$^+$ and CO$_3^{2-}$/HCO$_3^-$ is greatly affected by P-T conditions, decreasing with increasing pressure at 800$\\sim$1000 K. Our results suggest that in the Earth's upper ...

  20. Establishment and performance of an experimental green roof under extreme climatic conditions

    Energy Technology Data Exchange (ETDEWEB)

    Klein, Petra M., E-mail: pkklein@ou.edu [School of Meteorology, University of Oklahoma, Norman, OK (United States); Coffman, Reid, E-mail: rcoffma4@kent.edu [College of Architecture and Environmental Design, Kent State University, Kent, OH (United States)

    2015-04-15

    Green roofs alter the surface energy balance and can help in mitigating urban heat islands. However, the cooling of green roofs due to evapotranspiration strongly depends on the climatic conditions, and vegetation type and density. In the Southern Central Plains of the United States, extreme weather events, such as high winds, heat waves and drought conditions pose challenges for successful implementation of green roofs, and likely alter their standard performance. The National Weather Center Experimental Green Roof, an interdisciplinary research site established in 2010 in Norman, OK, aimed to investigate the ecological performance and surface energy balance of green roof systems. Starting in May 2010, 26 months of vegetation studies were conducted and the radiation balance, air temperature, relative humidity, and buoyancy fluxes were monitored at two meteorological stations during April–October 2011. The establishment of a vegetative community trended towards prairie plant dominance. High mortality of succulents and low germination of grasses and herbaceous plants contributed to low vegetative coverage. In this condition succulent diversity declined. Bouteloua gracilis and Delosperma cooperi showed typological dominance in harsh climatic conditions, while Sedum species experienced high mortality. The plant community diversified through volunteers such as Euphorbia maculate and Portulaca maculate. Net radiation measured at a green-roof meteorological station was higher than at a control station over the original, light-colored roofing material. These findings indicate that the albedo of the green roof was lower than the albedo of the original roofing material. The low vegetative coverage during the heat and drought conditions in 2011, which resulted in the dark substrate used in the green roof containers being exposed, likely contributed to the low albedo values. Nevertheless, air temperatures and buoyancy fluxes were often lower over the green roof indicating

  1. Research Article: Effects of long-term simulated Martian conditions on a freeze-dried and homogenized bacterial permafrost community

    DEFF Research Database (Denmark)

    Hansen, Aviaja Anna; Jensen, Lars Liengård; Kristoffersen, Tommy

    2009-01-01

    Indigenous bacteria and biomolecules (DNA and proteins) in a freeze-dried and homogenized Arctic permafrost were exposed to simulated martian conditions that correspond to about 80 days on the surface of Mars with respect to the accumulated UV dose. The simulation conditions included UV radiation...... and polynucleotides are more resistant to destruction than living biota. Astrobiology 9, 229-240....

  2. Century-scale causal relationships between global dry/wet conditions and the state of the Pacific and Atlantic Oceans

    Science.gov (United States)

    Sun, Qiaohong; Miao, Chiyuan; AghaKouchak, Amir; Duan, Qingyun

    2016-06-01

    The Granger causality test is used to examine the effects of the El Niño-Southern Oscillation (ENSO), the Pacific Decadal Oscillation (PDO), and the North Atlantic Oscillation (NAO) on global dry/wet conditions. The results show robust relationships between dry/wet conditions and the ocean states, as assessed through a multi-index (standardized precipitation evapotranspiration index and standardized precipitation index) and multiscale (3 months and 12 months) evaluation. The influence of ENSO events is widespread, dominating about 38% of the global land surface (excluding Antarctica). Southern and western North America, northern South America, and eastern Russia are influenced by the PDO. The NAO influences not only dry/wet conditions in Europe but also dry/wet conditions in northern Africa. Similarly, climate variability in southern Europe and northern Africa may be due to the concurrence of the ENSO and the NAO. Knowledge of the spatial influence of ocean states on global dry/wet conditions is valuable for improving drought and flood forecasting.

  3. Kelp and seaweed feeding by High-Arctic wild reindeer under extreme winter conditions

    Directory of Open Access Journals (Sweden)

    Brage Bremset Hansen

    2012-03-01

    Full Text Available One challenge in current Arctic ecological research is to understand and predict how wildlife may respond to increased frequencies of “extreme” weather events. Heavy rain-on-snow (ROS is one such extreme phenomenon associated with winter warming that is not well studied but has potentially profound ecosystem effects through changes in snow-pack properties and ice formation. Here, we document how ice-locked pastures following substantial amounts of ROS forced coastal Svalbard reindeer (Rangifer tarandus platyrhynchus to use marine habitat in late winter 2010. A thick coat of ground ice covered 98% of the lowland ranges, almost completely blocking access to terrestrial forage. Accordingly, a population census revealed that 13% of the total population (n=26 of 206 individuals and 21% of one sub-population were feeding on washed-up kelp and seaweed on the sea-ice foot. Calves were overrepresented among the individuals that applied this foraging strategy, which probably represents a last attempt to avoid starvation under particularly severe foraging conditions. The study adds to the impression that extreme weather events such as heavy ROS and associated icing can trigger large changes in the realized foraging niche of Arctic herbivores.

  4. Diamonds on Diamond: structural studies at extreme conditions on the Diamond Light Source.

    Science.gov (United States)

    McMahon, M I

    2015-03-06

    Extreme conditions (EC) research investigates how the structures and physical and chemical properties of materials change when subjected to extremes of pressure and temperature. Pressures in excess of one million times atmospheric pressure can be achieved using a diamond anvil cell, and, in combination with high-energy, micro-focused radiation from a third-generation synchrotron such as Diamond, detailed structural information can be obtained using either powder or single-crystal diffraction techniques. Here, I summarize some of the research drivers behind international EC research, and then briefly describe the techniques by which high-quality diffraction data are obtained. I then highlight the breadth of EC research possible on Diamond by summarizing four examples from work conducted on the I15 and I19 beamlines, including a study which resulted in the first research paper from Diamond. Finally, I look to the future, and speculate as to the type of EC research might be conducted at Diamond over the next 10 years.

  5. Outer scale and Monin-Obukhov flux relationships of atmospheric turbulence under dry convective conditions

    Science.gov (United States)

    De Bruin, Henk; Hartogensis, Oscar

    2015-04-01

    In this study we will investigate the assumption that in the atmospheric surface layer the outer scale (L0) is proportional to the height above the surface, under dry convective conditions. For this purpose we analyzed raw sonic anemometers data collected at 3.5 m and at 9 m in a field campaign at the Santa Cruz Flats (32040.3190'N, 111032.641'W, 526 m of elevation) near Eloy, Arizona. For simplicity, we define the L0 as that separation distance at which the spatial correlation coefficient of air temperature at two points in the surface layer is 0.5. Then, according to the 2/3-Kolmogorov scaling law in the inertial sub-range, L0 is determined by the variance and the structure parameter of T . It is found that L0 does not scale with height. Possible reasons for this negative result will be discussed, by considering the methodology to determine structure parameters, Taylor's frozen turbulence hypothesis, effects of intermittency and Monin-Obukhov flux relationships for variance and structure parameter for T . The question is asked whether the concept of surface constant flux layer still holds under strong convective condition.

  6. The microbial sulfur cycle at extremely haloalkaline conditions of soda lakes.

    Science.gov (United States)

    Sorokin, Dimitry Y; Kuenen, J Gijs; Muyzer, Gerard

    2011-01-01

    Soda lakes represent a unique ecosystem with extremely high pH (up to 11) and salinity (up to saturation) due to the presence of high concentrations of sodium carbonate in brines. Despite these double extreme conditions, most of the lakes are highly productive and contain a fully functional microbial system. The microbial sulfur cycle is among the most active in soda lakes. One of the explanations for that is high-energy efficiency of dissimilatory conversions of inorganic sulfur compounds, both oxidative and reductive, sufficient to cope with costly life at double extreme conditions. The oxidative part of the sulfur cycle is driven by chemolithoautotrophic haloalkaliphilic sulfur-oxidizing bacteria (SOB), which are unique for soda lakes. The haloalkaliphilic SOB are present in the surface sediment layer of various soda lakes at high numbers of up to 10(6) viable cells/cm(3). The culturable forms are so far represented by four novel genera within the Gammaproteobacteria, including the genera Thioalkalivibrio, Thioalkalimicrobium, Thioalkalispira, and Thioalkalibacter. The latter two were only found occasionally and each includes a single species, while the former two are widely distributed in various soda lakes over the world. The genus Thioalkalivibrio is the most physiologically diverse and covers the whole spectrum of salt/pH conditions present in soda lakes. Most importantly, the dominant subgroup of this genus is able to grow in saturated soda brines containing 4 M total Na(+) - a so far unique property for any known aerobic chemolithoautotroph. Furthermore, some species can use thiocyanate as a sole energy source and three out of nine species can grow anaerobically with nitrogen oxides as electron acceptor. The reductive part of the sulfur cycle is active in the anoxic layers of the sediments of soda lakes. The in situ measurements of sulfate reduction rates and laboratory experiments with sediment slurries using sulfate, thiosulfate, or elemental sulfur as

  7. Extreme midlatitude cyclones and their implications for precipitation and wind speed extremes in simulations of the Maunder Minimum versus present day conditions

    Energy Technology Data Exchange (ETDEWEB)

    Raible, C.C.; Casty, C. [University of Bern, Climate and Environmental Physics, Physics Institute, Bern (Switzerland); Yoshimori, M. [University of Bern, Climate and Environmental Physics, Physics Institute, Bern (Switzerland); Rutgers University, Center for Environmental Prediction, New Brunswick, NJ (United States); Stocker, T.F. [University of Bern, Climate and Environmental Physics, Physics Institute, Bern (Switzerland); University of Hawaii, International Pacific Research Center, SOEST, Honolulu, HI (United States)

    2007-03-15

    Extreme midlatitude cyclone characteristics, precipitation, wind speed events, their inter-relationships, and the connection to large-scale atmospheric patterns are investigated in simulations of a prolonged cold period, known as the Maunder Minimum from 1640 to 1715 and compared with today. An ensemble of six simulations for the Maunder Minimum as well as a control simulation for perpetual 1990 conditions are carried out with a coupled atmosphere-ocean general circulation model, i.e., the Climate Community System Model (CCSM). The comparison of the simulations shows that in a climate state colder than today the occurrence of cyclones, the extreme events of precipitation and wind speed shift southward in all seasons in the North Atlantic and the North Pacific. The extremes of cyclone intensity increases significantly in winter in almost all regions, which is related to a stronger meridional temperature gradient and an increase in lower tropospheric baroclinicity. Extremes of cyclone intensity in subregions of the North Atlantic are related to extremes in precipitation and in wind speed during winter. Moreover, extremes of cyclone intensity are also connected to distinct large-scale atmospheric patterns for the different subregions, but these relationships vanish during summer. Analyzing the mean 1,000 hPa geopotential height change of the Maunder Minimum simulations compared with the control simulation, we find a similar pattern as the correlation pattern with the cyclone intensity index of the southern Europe cyclones. This illustrates that changes in the atmospheric high-frequency, i.e., the simulated southward shift of cyclones in the North Atlantic and the related increase of extreme precipitation and wind speed in particular in the Mediterranean in winter, are associated with large-scale atmospheric circulation changes. (orig.)

  8. Sudden pore pressure rise and rapid landslide initiation induced under extreme rainfall conditions - a case study

    Science.gov (United States)

    Fukuoka, Hiroshi; Wang, Fawu; Wang, Gonghui

    2010-05-01

    Since July 19 to 26, 2009, western Japan had a severe rainstorms and caused floods and landslides. Most of the landslides are debris slide - debris flows. Most devastated case took place in Hofu city, Japan. On July 21, extremely intense rainstorm caused numerous debris flows and mud flows in the hillslopes Some of the debris flows destroyed residential houses and home for elderly people, and finally killed 14 residents. Debris flow distribution map was prepared soon based on airphoto interpretation. Japanese Meteorological Agency runs nation-wide ground-based rain gauge network as well as radar rain gauges, which provide hourly to 10 minutes precipitation distribution real-time with spatial resolution of about 5 km. Distribution of daily (cumulative) precipitation of July 21 shows (1) The cumulative precipitation from 6 am -- 12 am of the day was evaluated that their return period could be 200 - 600 years statistically. In 2009, another extraordinary rainfall, of which intensity was evaluated as less than 100 years more more, caused floods in another city claiming many residents lives on the way to evacuation area. Those frequent extraordinary extreme rainfall is not concluded as the consequence of global warming nor climate change, however, those frequency of extreme rainfall events affecting societies are obviously increasing in Japan, too. As for the Hofu city case, it was proved that debris flows took place in the high precipitation area and covered by covered by weathered granite sands and silts which is called "masa". This sands has been proved susceptible against landslides under extreme rainfall conditions. However, the transition from slide - debris flow process is not well revealed, except authors past experiment on the similar masa samples in June 1999 Hiroshima debris flow case. Authors have embedded pore pressure control system for the undrained ring shear apparatus. Strongly weathered sandy soils were sampled just on the smooth and flat granitic

  9. Foundations of high-energy-density physics physical processes of matter at extreme conditions

    CERN Document Server

    Larsen, Jon

    2017-01-01

    High-energy-density physics explores the dynamics of matter at extreme conditions. This encompasses temperatures and densities far greater than we experience on Earth. It applies to normal stars, exploding stars, active galaxies, and planetary interiors. High-energy-density matter is found on Earth in the explosion of nuclear weapons and in laboratories with high-powered lasers or pulsed-power machines. The physics explored in this book is the basis for large-scale simulation codes needed to interpret experimental results whether from astrophysical observations or laboratory-scale experiments. The key elements of high-energy-density physics covered are gas dynamics, ionization, thermal energy transport, and radiation transfer, intense electromagnetic waves, and their dynamical coupling. Implicit in this is a fundamental understanding of hydrodynamics, plasma physics, atomic physics, quantum mechanics, and electromagnetic theory. Beginning with a summary of the topics and exploring the major ones in depth, thi...

  10. Development of a system for simultaneously generating triple extreme conditions for neutron scattering experiments

    Energy Technology Data Exchange (ETDEWEB)

    Ichimura, Shigeju [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

    1998-10-01

    We have developed new system available for controlling sample environment during the neutron scattering experiments. The system can simultaneously generate triple extreme conditions of low temperature, high magnetic field and high pressure. The system consists of : (1) a liquid-helium cryostat which enables the sample temperature range of 1.7 K to 200 K, (2) a superconducting magnet providing a vertical field up to 5 Tesla with antisymmetric split-coil geometry for polarized-beam experiments, and (3) a non-magnetic clamping high-pressure cell designed with the aim of generating hydrostatic pressure up to 2.5 Gpa. In the workshop, we will report the outline of the system and some results of performance tests using the system at JRR-3M of JAERI. (author)

  11. Nanocomposite polymeric electrolytes to record electrophysiological brain signals in prolonged, unconventional or extreme conditions.

    Science.gov (United States)

    Licoccia, Silvia; Luisa Di Vona, M; Romagnoli, Paola; Narici, Livio; Acquaviva, Massimo; Carozzo, Simone; Marco, Stefano Di; Saturno, Moreno; Sannita, Walter G; Traversa, Enrico

    2006-09-01

    Chemically stable nanocomposite iono-conducting polymeric membranes (based on lithium salts and nanocrystalline oxide powders dispersed in a polymethyl methacrylate matrix) performed successfully in the recording of human brain responses to visual stimulation. Impedance was higher than that of conventional electrodes. However, the electrophysiological signals recorded by acid Al(2)O(3) and neutral Al(2)O(3) 5 wt.% and 10 wt.% nanocomposite gel electrolytes were comparable to those obtained with standard electrodes, even without preliminary skin cleaning and in the absence of gel electrolytes allowing better contact with and skin-electrode ionic conductance. The electrochemical and mechanical characteristics of these membranes make them fit for human and animal research, for clinical application (specifically in emergencies, prolonged electrophysiological recordings), or in unconventional or extreme conditions when fluid electrolytes are unsuitable (e.g., biomedical space research).

  12. Seed storage at elevated partial pressure of oxygen, a fast method for analysing seed ageing under dry conditions

    Science.gov (United States)

    Groot, S. P. C.; Surki, A. A.; de Vos, R. C. H.; Kodde, J.

    2012-01-01

    Background and Aims Despite differences in physiology between dry and relative moist seeds, seed ageing tests most often use a temperature and seed moisture level that are higher than during dry storage used in commercial practice and gene banks. This study aimed to test whether seed ageing under dry conditions can be accelerated by storing under high-pressure oxygen. Methods Dry barley (Hordeum vulgare), cabbage (Brassica oleracea), lettuce (Lactuca sativa) and soybean (Glycine max) seeds were stored between 2 and 7 weeks in steel tanks under 18 MPa partial pressure of oxygen. Storage under high-pressure nitrogen gas or under ambient air pressure served as controls. The method was compared with storage at 45 °C after equilibration at 85 % relative humidity and long-term storage at the laboratory bench. Germination behaviour, seedling morphology and tocopherol levels were assessed. Key Results The ageing of the dry seeds was indeed accelerated by storing under high-pressure oxygen. The morphological ageing symptoms of the stored seeds resembled those observed after ageing under long-term dry storage conditions. Barley appeared more tolerant of this storage treatment compared with lettuce and soybean. Less-mature harvested cabbage seeds were more sensitive, as was the case for primed compared with non-primed lettuce seeds. Under high-pressure oxygen storage the tocopherol levels of dry seeds decreased, in a linear way with the decline in seed germination, but remained unchanged in seeds deteriorated during storage at 45 °C after equilibration at 85 % RH. Conclusions Seed storage under high-pressure oxygen offers a novel and relatively fast method to study the physiology and biochemistry of seed ageing at different seed moisture levels and temperatures, including those that are representative of the dry storage conditions as used in gene banks and commercial practice. PMID:22967856

  13. High Efficiency Liquid-Desiccant Regenerator for Air Conditioning and Industrial Drying

    Energy Technology Data Exchange (ETDEWEB)

    Andrew Lowenstein

    2005-12-19

    Over 2 quads of fossil fuels are used each year for moisture removal. This includes industrial and agricultural processes where feedstocks and final products must be dried, as well as comfort conditioning of indoor spaces where the control of humidity is essential to maintaining healthy, productive and comfortable working conditions. Desiccants, materials that have a high affinity for water vapor, can greatly reduce energy use for both drying and dehumidification. An opportunity exists to greatly improve the competitiveness of advanced liquid-desiccant systems by increasing the efficiency of their regenerators. It is common practice within the chemical process industry to use multiple stage boilers to improve the efficiency of thermal separation processes. The energy needed to regenerate a liquid desiccant, which is a thermal separation process, can also be reduced by using a multiple stage boiler. In this project, a two-stage regenerator was developed in which the first stage is a boiler and the second stage is a scavenging-air regenerator. The only energy input to this regenerator is the natural gas that fires the boiler. The steam produced in the boiler provides the thermal energy to run the second-stage scavenging-air regenerator. This two-stage regenerator is referred to as a 1?-effect regenerator. A model of the high-temperature stage of a 1?-effect regenerator for liquid desiccants was designed, built and successfully tested. At nominal operating conditions (i.e., 2.35 gpm of 36% lithium chloride solution, 307,000 Btu/h firing rate), the boiler removed 153 lb/h of water from the desiccant at a gas-based efficiency of 52.9 % (which corresponds to a COP of 0.95 when a scavenging-air regenerator is added). The steam leaving the boiler, when condensed, had a solids concentration of less than 10 ppm. This low level of solids in the condensate places an upper bound of about 6 lb per year for desiccant loss from the regenerator. This low loss will not create

  14. High-fidelity numerical modeling of the Upper Mississippi River under extreme flood condition

    Science.gov (United States)

    Khosronejad, Ali; Le, Trung; DeWall, Petra; Bartelt, Nicole; Woldeamlak, Solomon; Yang, Xiaolei; Sotiropoulos, Fotis

    2016-12-01

    We present data-driven numerical simulations of extreme flooding in a large-scale river coupling coherent-structure resolving hydrodynamics with bed morphodynamics under live-bed conditions. The study area is a ∼ 3.2 km long and ∼ 300 m wide reach of the Upper Mississippi River, near Minneapolis MN, which contains several natural islands and man-made hydraulic structures. We employ the large-eddy simulation (LES) and bed-morphodynamic modules of the Virtual Flow Simulator (VFS-Rivers) model, a recently developed in-house code, to investigate the flow and bed evolution of the river during a 100-year flood event. The coupling of the two modules is carried out via a fluid-structure interaction approach using a nested domain approach to enhance the resolution of bridge scour predictions. We integrate data from airborne Light Detection and Ranging (LiDAR), sub-aqueous sonar apparatus on-board a boat and in-situ laser scanners to construct a digital elevation model of the river bathymetry and surrounding flood plain, including islands and bridge piers. A field campaign under base-flow condition is also carried out to collect mean flow measurements via Acoustic Doppler Current Profiler (ADCP) to validate the hydrodynamic module of the VFS-Rivers model. Our simulation results for the bed evolution of the river under the 100-year flood reveal complex sediment transport dynamics near the bridge piers consisting of both scour and refilling events due to the continuous passage of sand dunes. We find that the scour depth near the bridge piers can reach to a maximum of ∼ 9 m. The data-driven simulation strategy we present in this work exemplifies a practical simulation-based-engineering-approach to investigate the resilience of infrastructures to extreme flood events in intricate field-scale riverine systems.

  15. Optimisation of spray drying operating conditions of Morinda citrifolia L. fruit extract using response surface methodology

    OpenAIRE

    2015-01-01

    A conventional solvent extract of Morinda citrifolia L. fruit was spray dried using adjuvant maltodextrin (5 wt.%). Spray drying was carried out according to the D-optimal design, and the independent variables selected were temperature and Mcore/Mwall. The spray drying process was optimised by using response surface methodology (RSM) for four different responses: moisture content (MC), DPPH scavenging activity, total phenolic content (TPC), and total flavonoid (TF). The effects of temperature...

  16. Ambient Dried Aerogels

    Science.gov (United States)

    Jones, Steven M.; Paik, Jong-Ah

    2013-01-01

    A method has been developed for creating aerogel using normal pressure and ambient temperatures. All spacecraft, satellites, and landers require the use of thermal insulation due to the extreme environments encountered in space and on extraterrestrial bodies. Ambient dried aerogels introduce the possibility of using aerogel as thermal insulation in a wide variety of instances where supercritically dried aerogels cannot be used. More specifically, thermoelectric devices can use ambient dried aerogel, where the advantages are in situ production using the cast-in ability of an aerogel. Previously, aerogels required supercritical conditions (high temperature and high pressure) to be dried. Ambient dried aerogels can be dried at room temperature and pressure. This allows many materials, such as plastics and certain metal alloys that cannot survive supercritical conditions, to be directly immersed in liquid aerogel precursor and then encapsulated in the final, dried aerogel. Additionally, the metalized Mylar films that could not survive the previous methods of making aerogels can survive the ambient drying technique, thus making multilayer insulation (MLI) materials possible. This results in lighter insulation material as well. Because this innovation does not require high-temperature or high-pressure drying, ambient dried aerogels are much less expensive to produce. The equipment needed to conduct supercritical drying costs many tens of thousands of dollars, and has associated running expenses for power, pressurized gasses, and maintenance. The ambient drying process also expands the size of the pieces of aerogel that can be made because a high-temperature, high-pressure system typically has internal dimensions of up to 30 cm in diameter and 60 cm in height. In the case of this innovation, the only limitation on the size of the aerogels produced would be in the ability of the solvent in the wet gel to escape from the gel network.

  17. Establishment and performance of an experimental green roof under extreme climatic conditions.

    Science.gov (United States)

    Klein, Petra M; Coffman, Reid

    2015-04-15

    Green roofs alter the surface energy balance and can help in mitigating urban heat islands. However, the cooling of green roofs due to evapotranspiration strongly depends on the climatic conditions, and vegetation type and density. In the Southern Central Plains of the United States, extreme weather events, such as high winds, heat waves and drought conditions pose challenges for successful implementation of green roofs, and likely alter their standard performance. The National Weather Center Experimental Green Roof, an interdisciplinary research site established in 2010 in Norman, OK, aimed to investigate the ecological performance and surface energy balance of green roof systems. Starting in May 2010, 26 months of vegetation studies were conducted and the radiation balance, air temperature, relative humidity, and buoyancy fluxes were monitored at two meteorological stations during April-October 2011. The establishment of a vegetative community trended towards prairie plant dominance. High mortality of succulents and low germination of grasses and herbaceous plants contributed to low vegetative coverage. In this condition succulent diversity declined. Bouteloua gracilis and Delosperma cooperi showed typological dominance in harsh climatic conditions, while Sedum species experienced high mortality. The plant community diversified through volunteers such as Euphorbia maculate and Portulaca maculate. Net radiation measured at a green-roof meteorological station was higher than at a control station over the original, light-colored roofing material. These findings indicate that the albedo of the green roof was lower than the albedo of the original roofing material. The low vegetative coverage during the heat and drought conditions in 2011, which resulted in the dark substrate used in the green roof containers being exposed, likely contributed to the low albedo values. Nevertheless, air temperatures and buoyancy fluxes were often lower over the green roof indicating

  18. Rapid measurement and evaluation of the effect of drying conditions on harpagoside content in Harpagophytum procumbens (devil's claw) root.

    Science.gov (United States)

    Joubert, Elizabeth; Manley, Marena; Gray, Brian R; Schulz, Hartwig

    2005-05-04

    The effect of drying conditions on harpagoside (HS) retention, as well as the use of near-infrared spectroscopy (NIRS) for rapid quantification of the iridoids, HS, and 8-rho-coumaroyl harpagide (8rhoCHG) and moisture, in dried Harpagophytum procumbens (devil's claw) root was investigated. HS retention was significantly (P < 0.05) lower in sun-dried samples as compared to tunnel-dried (60 degrees C, 30% relative humidity) and freeze-dried samples. The best retention of HS was obtained at 50 degrees C when evaluating tunnel drying at dry bulb temperatures of 40, 50, and 60 degrees C and 30% relative humidity. NIRS can effectively predict moisture content with a standard error of prediction (SEP) and correlation coefficient (r) of 0.24% and 0.99, respectively. The HS and 8rhoCHG NIRS calibration models established for both iridoid glucosides can be used for screening purposes to get a semiquantitative classification of devil's claw roots (for HS: SEP = 0.236%, r = 0.64; for 8rhoCHG: SEP = 0.048%, r = 0.73).

  19. Solar Wind Interaction with the Martian Upper Atmosphere at Early Mars/Extreme Solar Conditions

    Science.gov (United States)

    Dong, C.; Bougher, S. W.; Ma, Y.; Toth, G.; Lee, Y.; Nagy, A. F.; Tenishev, V.; Pawlowski, D. J.; Combi, M. R.

    2014-12-01

    The investigation of ion escape fluxes from Mars, resulting from the solar wind interaction with its upper atmosphere/ionosphere, is important due to its potential impact on the long-term evolution of Mars atmosphere (e.g., loss of water) over its history. In the present work, we adopt the 3-D Mars cold neutral atmosphere profiles (0 ~ 300 km) from the newly developed and validated Mars Global Ionosphere Thermosphere Model (M-GITM) and the 3-D hot oxygen profiles (100 km ~ 5 RM) from the exosphere Monte Carlo model Adaptive Mesh Particle Simulator (AMPS). We apply these 3-D model output fields into the 3-D BATS-R-US Mars multi-fluid MHD (MF-MHD) model (100 km ~ 20 RM) that can simulate the interplay between Mars upper atmosphere and solar wind by considering the dynamics of individual ion species. The multi-fluid MHD model solves separate continuity, momentum and energy equations for each ion species (H+, O+, O2+, CO2+). The M-GITM model together with the AMPS exosphere model take into account the effects of solar cycle and seasonal variations on both cold and hot neutral atmospheres. This feature allows us to investigate the corresponding effects on the Mars upper atmosphere ion escape by using a one-way coupling approach, i.e., both the M-GITM and AMPS model output fields are used as the input for the multi-fluid MHD model and the M-GITM is used as input into the AMPS exosphere model. In this study, we present M-GITM, AMPS, and MF-MHD calculations (1-way coupled) for 2.5 GYA conditions and/or extreme solar conditions for present day Mars (high solar wind velocities, high solar wind dynamic pressure, and high solar irradiance conditions, etc.). Present day extreme conditions may result in MF-MHD outputs that are similar to 2.5 GYA cases. The crustal field orientations are also considered in this study. By comparing estimates of past ion escape rates with the current ion loss rates to be returned by the MAVEN spacecraft (2013-2016), we can better constrain the

  20. Characterization of Multi-Scale Atmospheric Conditions Associated with Extreme Precipitation in the Transverse Ranges of Southern California

    Science.gov (United States)

    Oakley, N.; Kaplan, M.; Ralph, F. M.

    2015-12-01

    The east-west oriented Transverse Ranges of Southern California have historically experienced shallow landslides and debris flows that threaten life and property. Steep topography, soil composition, and frequent wildfires make this area susceptible to mass wasting. Extreme rainfall often acts as a trigger for these events. This work characterizes atmospheric conditions at multiple scales during extreme (>99th percentile) 1-day precipitation events in the major sub-ranges of the Transverse Ranges. Totals from these 1-day events generally exceed the established sub-daily intensity-duration thresholds for shallow landslides and debris flows in this region. Daily extreme precipitation values are derived from both gridded and station-based datasets over the period 1958-2014. For each major sub-range, extreme events are clustered by atmospheric feature and direction of moisture transport. A composite analysis of synoptic conditions is produced for each cluster to create a conceptual model of atmospheric conditions favoring extreme precipitation. The vertical structure of the atmosphere during these extreme events is also examined using observed and modeled soundings. Preliminary results show two atmospheric features to be of importance: 1) closed and cutoff low-pressure systems, areas of counter-clockwise circulation that can produce southerly flow orthogonal to the Transverse Range ridge axes; and 2) atmospheric rivers that transport large quantities of water vapor into the region. In some cases, the closed lows and atmospheric rivers work in concert with each other to produce extreme precipitation. Additionally, there is a notable east-west dipole of precipitation totals during some extreme events between the San Gabriel and Santa Ynez Mountains where extreme values are observed in one range and not the other. The cause of this relationship is explored. The results of this work can help forecasters and emergency responders determine the likelihood that an event will

  1. The near-term prediction of drought and flooding conditions in the northeastern United States based on extreme phases of AMO and NAO

    Science.gov (United States)

    Berton, Rouzbeh; Driscoll, Charles T.; Adamowski, Jan F.

    2017-10-01

    frequency of wet, average, and dry discharge conditions with regards to the extreme phases of AMO and NAO. While the function was decaying, the tail asymptotically merged into and stabilized at the theoretical probability of the event. As the basin scale increased, the probability of wet, average, and dry discharge conditions decreased. The Merrimack River watershed will most likely experience greater than average discharge as its extreme condition, therefore development should be avoided on flood plains. Furthermore, the current reservoir storage capacity in the Merrimack should be improved in order to accommodate excess water input and minimize flood damage. Future research should target changes in the magnitude and timing of high discharge events in order to develop adaptation strategies for aging hydraulic infrastructure in the region.

  2. Effect of drying conditions on triticale seed germination and weevil infestation

    Science.gov (United States)

    The combination of high protein content and a soft seed coat makes triticale vulnerable to attack by weevils. Drying triticale grain to moisture contents safe for storage can prevent infestation by weevils, but if grain is being stored for seed, high drying temperatures can affect seed germination. ...

  3. Simulating the effect of conditioning on the drying of cut grass

    NARCIS (Netherlands)

    Lorenzi, de F.; Bosma, A.H.; Stanghellini, C.

    1996-01-01

    Field wilting and drying of hay is an important agricultural process upon which the quality of material subsequently conserved is dependent. The research described here aims at translating the biophysical processes that affect field drying of grass into parameters sets to be used for decision suppor

  4. Circuits and signal conditioning for a peanut-drying monitoring system

    Science.gov (United States)

    Post-harvest processes at peanut buying points and other peanut grading facilities have a direct impact on the quality of the product. Peanut drying is an essential task for safe peanut storage. The rate at which peanuts are dried can also affect the flavor and milling qualities. Current peanut dryi...

  5. Rainwater harvesting to alleviate water scarcity in dry conditions: A case study in Faria Catchment, Palestine

    Directory of Open Access Journals (Sweden)

    Sameer SHADEED

    2010-06-01

    Full Text Available In arid and semi-arid regions, the availability of adequate water of appropriate quality has become a limiting factor for development. This paper aims to evaluate the potential for rainwater harvesting in the arid to semi-arid Faria Catchment, in the West Bank, Palestine. Under current conditions, the supply-demand gap is increasing due to the increasing water demands of a growing population with hydrologically limited and uncertain supplies. By 2015, the gap is estimated to reach 4.5 × 106 m3. This study used the process-oriented and physically-based TRAIN-ZIN model to evaluate two different rainwater harvesting techniques during two rainfall events. The analysis shows that there is a theoretical potential for harvesting an additional 4 × 106 m3 of surface water over the entire catchment. Thus, it is essential to manage the potential available surface water supplies in the catchment to save water for dry periods when the supply-demand gap is comparatively high. Then a valuable contribution to bridging the supply-demand gap can be made.

  6. Effects of spray-drying conditions on the chemical, physical, and sensory properties of cheese powder.

    Science.gov (United States)

    Koca, Nurcan; Erbay, Zafer; Kaymak-Ertekin, Figen

    2015-05-01

    Dairy powders are produced to increase the shelf life of fresh dairy products and for use as flavoring agents. In this study, 24 cheese powders produced under 7 different conditions were used to investigate the effects of spray-drying parameters (e.g., inlet air temperature, atomization pressure, and outlet air temperature) on the quality of white cheese powder. Composition, color, physical properties, reconstitution, and sensory characteristics of white cheese powders were determined. The results revealed that the white cheese powders produced in this study had low moisture content ratios and water activity values. High outlet air temperatures caused browning and enhanced Maillard reactions. Additionally, high outlet air temperatures increased wettability and dispersibility and decreased the solubility of white cheese powders. Free fat content was positively correlated with inlet air temperature and negatively correlated with outlet air temperature and atomization pressure. Sensory analyses revealed that white cheese powder samples had acceptable sensory characteristics with the exception of the sample produced at an outlet air temperature of 100°C, which had high scores for scorched flavor and color and low scores for cheese flavor.

  7. A new fluorescent pH probe for extremely acidic conditions

    Energy Technology Data Exchange (ETDEWEB)

    Xu, Yu [School of Chemistry and Chemical Engineering, Shandong University, Jinan 250100 (China); Taishan College, Shandong University, Jinan 250100 (China); Jiang, Zheng [School of Life Science, Shandong University, Jinan 250100 (China); Taishan College, Shandong University, Jinan 250100 (China); Xiao, Yu [School of Chemistry and Chemical Engineering, Shandong University, Jinan 250100 (China); Taishan College, Shandong University, Jinan 250100 (China); Bi, Fu-Zhen [School of Chemistry and Chemical Engineering, Shandong University, Jinan 250100 (China); Miao, Jun-Ying, E-mail: miaojy@sdu.edu.cn [School of Life Science, Shandong University, Jinan 250100 (China); Zhao, Bao-Xiang, E-mail: bxzhao@sdu.edu.cn [School of Chemistry and Chemical Engineering, Shandong University, Jinan 250100 (China)

    2014-04-01

    A new coumarin-based fluorescent probe can detect highly acidic conditions in both solution and bacteria with high selectivity and sensitivity. Highlights: • A new fluorescence probe for very low pH was synthesized and characterized. • The probe can monitor pH in solution and bacteria. • The two-step protonation of N atoms of the probe leads to fluorescence quenching. Abstract: A novel turn-off fluorescent probe based on coumarin and imidazole moiety for extremely acidic conditions was designed and developed. The probe with pKa = 2.1 is able to respond to very low pH value (below 3.5) with high sensitivity relying on fluorescence quenching at 460 nm in fluorescence spectra or the ratios of absorbance maximum at 380 nm to that at 450 nm in UV–vis spectra. It can quantitatively detect pH value based on equilibrium equation, pH = pKa -log[(Ix - Ib)/(Ia - Ix)]. It had very short response time that was less than 1 min, good reversibility and nearly no interference from common metal ions. Moreover, using ¹H NMR analysis and theoretical calculation of molecular orbital, we verified that a two-step protonation process of two N atoms of the probe leaded to photoinduced electron transfer (PET), which was actually the mechanism of the fluorescence quenching phenomenon under strongly acidic conditions. Furthermore, the probe was also applied to imaging strong acidity in bacteria, E.coli and had good effect. This work illustrates that the new probe could be a practical and ideal pH indicator for strongly acidic conditions with good biological significance.

  8. Response of ecosystem productivity to dry/wet conditions indicated by different drought indices.

    Science.gov (United States)

    Wang, Haiyan; He, Bin; Zhang, Yafeng; Huang, Ling; Chen, Ziyue; Liu, Junjie

    2017-08-28

    Various climatic and hydrological variables such as precipitation, soil moisture, stream flow, and water level can be used to assess drought conditions, however, the response of ecosystem productivity to such metrics is not very clear. In this study, we examined the sensitivity of GPP anomalies to five drought indicators: the Standardized Precipitation Index (SPI), the Standardized Precipitation-Evapotranspiration Index (SPEI), Palmer Drought Severity Index (PDSI), deficit of soil moisture (DSM), and the difference between precipitation (P) and evapotranspiration (ET) (D(P-ET)). The global spatial distributions of drying and wetting trends from 2000 to 2014 determined by these five indices were similar. Additionally, the percent of drought-impacted areas decreased over the study period, indicating a reduction in drought conditions. GPP increased over the study period in the Northern Hemisphere (NH) but decreased in the Southern Hemisphere (SH), resulting in a net increase in global GPP. GPP anomalies were more sensitive to drought indices in the SH than in the NH. Among the five indices, GPP anomalies were most closely correlated with SPI in the NH (R=0.60, P<0.05) and SPEI in the SH (R=0.93, P<0.01). Regionally speaking, annual and seasonal GPP anomalies were most sensitive to DSM and PDSI, highlighting the importance of soil moisture observations to regional drought monitoring and assessment. The results of this study are important for evaluating the impacts of drought on ecosystem production and the global carbon cycle. Copyright © 2017 Elsevier B.V. All rights reserved.

  9. Comparison of diagnostic tests in distinct well-defined conditions related to dry eye disease.

    Directory of Open Access Journals (Sweden)

    Monica Alves

    Full Text Available PURPOSE: This study compares signs, symptoms and predictive tools used to diagnose dry eye disease (DED and ocular surface disorders in six systemic well-defined and non-overlapping diseases. It is well known that these tests are problematic because of a lack of agreement between them in identifying these conditions. Accordingly, we provide here a comparative clinical profile analysis of these different diseases. METHODS: A spontaneous and continuous sample of patients with Sjögren's syndrome (SS (n=27, graft-versus-host-disease (GVHD (n=28, Graves orbitopathy (n=28, facial palsy (n=8, diabetes mellitus without proliferative retinopathy (n=14 and glaucoma who chronically received topical drugs preserved with benzalkonium chloride (n=20 were enrolled. Evaluation consisted of a comprehensive protocol encompassing: (1 structured questionnaire - Ocular Surface Disease Index (OSDI; (2 tear osmolarity (TearLab Osmolarity System - Ocusense; (3 tear film break-up time (TBUT; (4 fluorescein and lissamine green staining; (5 Schirmer test and (6 severity grading. RESULTS: One hundred and twenty five patients (aged 48.8 years-old ± 14.1, male:female ratio=0.4 were enrolled in the study, along with 24 age and gender matched controls. Higher scores on DED tests were obtained in Sjögren Syndrome (P<0.05, except for tear film osmolarity that was higher in diabetics (P<0.001 and fluorescein staining, that was higher in facial palsy (P<0.001. TFBUT and OSDI correlated better with other tests. The best combination of diagnostic tests for DED was OSDI, TBUT and Schirmer test (sensitivity 100%, specificity 95% and accuracy 99.3%. CONCLUSIONS: DED diagnostic test results present a broad range of variability among different conditions. Vital stainings and TBUT correlated best with one another whereas the best test combination to detect DED was: OSDI/TBUT/Schirmer.

  10. The influence of surface type on the absorbed radiation by a human under hot, dry conditions

    Science.gov (United States)

    Hardin, A. W.; Vanos, J. K.

    2017-05-01

    Given the predominant use of heat-retaining materials in urban areas, numerous studies have addressed the urban heat island mitigation potential of various "cool" options, such as vegetation and high-albedo surfaces. The influence of altered radiational properties of such surfaces affects not only the air temperature within a microclimate, but more importantly the interactions of long- and short-wave radiation fluxes with the human body. Minimal studies have assessed how cool surfaces affect thermal comfort via changes in absorbed radiation by a human (R abs) using real-world, rather than modeled, urban field data. The purpose of the current study is to assess the changes in the absorbed radiation by a human—a critical component of human energy budget models—based on surface type on hot summer days (air temperatures > 38.5∘C). Field tests were conducted using a high-end microclimate station under predominantly clear sky conditions over ten surfaces with higher sky view factors in Lubbock, Texas. Three methods were used to measure and estimate R abs: a cylindrical radiation thermometer (CRT), a net radiometer, and a theoretical estimation model. Results over dry surfaces suggest that the use of high-albedo surfaces to reduce overall urban heat gain may not improve acute human thermal comfort in clear conditions due to increased reflected radiation. Further, the use of low-cost instrumentation, such as the CRT, shows potential in quantifying radiative heat loads within urban areas at temporal scales of 5-10 min or greater, yet further research is needed. Fine-scale radiative information in urban areas can aid in the decision-making process for urban heat mitigation using non-vegetated urban surfaces, with surface type choice is dependent on the need for short-term thermal comfort, or reducing cumulative heat gain to the urban fabric.

  11. Predicting the solubility of gases in Nitrile Butadiene Rubber in extreme conditions using molecular simulation

    Science.gov (United States)

    Khawaja, Musab; Molinari, Nicola; Sutton, Adrian; Mostofi, Arash

    In the oil and gas industry, elastomer seals play an important role in protecting sensitive monitoring equipment from contamination by gases - a problem that is exacerbated by the high pressures and temperatures found down-hole. The ability to predict and prevent such permeative failure has proved elusive to-date. Nitrile butadiene rubber (NBR) is a common choice of elastomer for seals due to its resistance to heat and fuels. In the conditions found in the well it readily absorbs small molecular weight gases. How this behaviour changes quantitatively for different gases as a function of temperature and pressure is not well-understood. In this work a series of fully atomistic simulations are performed to understand the effect of extreme conditions on gas solubility in NBR. Widom particle insertion is used to compute solubilities. The importance of sampling and allowing structural relaxation upon compression are highlighted, and qualitatively reasonable trends reproduced. Finally, while at STP it has previously been shown that the solubility of CO2 is higher than that of He in NBR, we observe that under the right circumstances it is possible to reverse this trend.

  12. Extreme sensory processing patterns and their relation with clinical conditions among individuals with major affective disorders.

    Science.gov (United States)

    Engel-Yeger, Batya; Muzio, Caterina; Rinosi, Giorgio; Solano, Paola; Geoffroy, Pierre Alexis; Pompili, Maurizio; Amore, Mario; Serafini, Gianluca

    2016-02-28

    Previous studies highlighted the involvement of sensory perception in emotional processes. However, the role of extreme sensory processing patterns expressed in hyper- or hyposensitivity was not thoroughly considered. The present study, in real life conditions, examined the unique sensory processing patterns of individuals with major affective disorders and their relationship with psychiatric symptomatology. The sample consisted of 105 participants with major affective conditions ranging in age from 20 to 84 years (mean=56.7±14.6). All participants completed the Temperament Evaluation of Memphis, Pisa, Paris and San Diego (TEMPS-A), the second version of the Beck Depression Inventory (BDI-II), and Adolescent/Adult Sensory Profile (AASP). Sensory sensitivity/avoiding hypersensitivity patterns and low registration (a hyposensitivity pattern) were prevalent among our sample as compared to normative data. About seventy percent of the sample showed lower seeking tendency. Stepwise regression analyses revealed that depression and anxious/cyclothymic affective temperaments were predicted by sensory sensory/avoiding. Anxious and irritable affective temperaments were predicted by low registration. Hyperthymic affective temperament and lower severity of depression were predicted by sensation seeking. Hyposensitivity or hypersensitivity may be "trait" markers of individuals with major affective disorders. Interventions should refer to the individual unique sensory profiles and their behavioral and functional impact in the context of real life.

  13. Cell viability of microencapsulated Bifidobacterium animalis subsp. lactis under freeze-drying, storage and gastrointestinal tract simulation conditions.

    Science.gov (United States)

    Shamekhi, Fatemeh; Shuhaimi, Mustafa; Ariff, Arbakariya; Manap, Yazid A

    2013-03-01

    The purpose of this study was to improve the survival of Bifidobacterium animalis subsp. lactis 10140 during freeze-drying process by microencapsulation, using a special pediatric prebiotics mixture (galactooligosaccharides and fructooligosaccharides). Probiotic microorganisms were encapsulated with a coat combination of prebiotics-calcium-alginate prior to freeze-drying. Both encapsulated and free cells were then freeze-dried in their optimized combinations of skim milk and prebiotics. Response surface methodology (RSM) was used to produce a coating combination as well as drying medium with the highest cell viability during freeze-drying. The optimum encapsulation composition was found to be 2.1 % Na-alginate, 2.9 % prebiotic, and 21.7 % glycerol. Maximum survival predicted by the model was 81.2 %. No significant (p > 0.05) difference between the predicted and experimental values verified the adequacy of final reduced models. The protection ability of encapsulation was then examined over 120 days of storage at 4 and 25 °C and exposure to a sequential model of infantile GIT conditions including both gastric conditions (pH 3.0 and 4.0, 90 min, 37 °C) and intestinal conditions (pH 7.5, 5 h, 37 °C). Significantly improved cell viability showed that microencapsulation of B. lactis 10140 with the prebiotics was successful in producing a stable symbiotic powdery nutraceutical.

  14. Regional metamorphism at extreme conditions: Implications for orogeny at convergent plate margins

    Science.gov (United States)

    Zheng, Yong-Fei; Chen, Ren-Xu

    2017-09-01

    Regional metamorphism at extreme conditions refers either to Alpine-type metamorphism at low geothermal gradients of 30 °C/km. Extreme pressures refer to those above the polymorphic transition of quartz to coesite, so that ultrahigh-pressure (UHP) eclogite-facies metamorphism occurs at mantle depths of >80 km. Extreme temperatures refer to those higher than 900 °C at crustal depths of ≤80 km, so that ultrahigh-temperature (UHT) granulite-facies metamorphism occurs at medium to high pressures. While crustal subduction at the low geothermal gradients results in blueschist-eclogite facies series without arc volcanism, heating of the thinned orogenic lithosphere brings about the high geothermal gradients for amphibolite-granulite facies series with abundant magmatism. Therefore, UHP metamorphic rocks result from cold lithospheric subduction to the mantle depths, whereas UHT metamorphic rocks are produced by hot underplating of the asthenospheric mantle at the crustal depths. Active continental rifting is developed on the thinned lithosphere in response to asthenospheric upwelling, and this tectonism is suggested as a feasible mechanism for regional granulite-facies metamorphism, with the maximum temperature depending on the extent to which the mantle lithosphere is thinned prior to the rifting. While lithospheric compression is associated with subduction metamorphism in accretionary and collisional orogens, the thinned orogenic lithosphere undergoes extension due to the asthenospheric upwelling to result in orogen-parallel rifting metamorphism and magmatism. Thus, the rifting metamorphism provides a complement to the subduction metamorphism and its operation marks the asthenospheric heating of the orogenic lithosphere. Because of the partial melting and melt extraction of the lower continental crust, contemporaneous granite-migmatite-granulite associations may serve as a petrological indicator of rifting orogeny that is superimposed on precedingly accretionary and

  15. Final Report - Membranes and MEA's for Dry, Hot Operating Conditions

    Energy Technology Data Exchange (ETDEWEB)

    Hamrock, Steven J

    2011-06-30

    The focus of this program was to develop a new Proton Exchange Membrane (PEM) which can operate under hotter, dryer conditions than the state of the art membranes today and integrate it into a Membrane Electrode Assembly (MEA). These MEA's should meet the performance and durability requirements outlined in the solicitation, operating under low humidification conditions and at temperatures ranging from -20ºC to 120ºC, to meet 2010 DOE technical targets for membranes. This membrane should operate under low humidification conditions and at temperatures ranging from -20ºC to 120ºC in order to meet DOE HFCIT 2010 commercialization targets for automotive fuel cells. Membranes developed in this program may also have improved durability and performance characteristics making them useful in stationary fuel cell applications. The new membranes, and the MEA's comprising them, should be manufacturable at high volumes and at costs which can meet industry and DOE targets. This work included: A) Studies to better understand factors controlling proton transport within the electrolyte membrane, mechanisms of polymer degradation (in situ and ex situ) and membrane durability in an MEA; B) Development of new polymers with increased proton conductivity over the range of temperatures from -20ºC to 120ºC and at lower levels of humidification and with improved chemical and mechanical stability; C) Development of new membrane additives for increased durability and conductivity under these dry conditions; D) Integration of these new materials into membranes and membranes into MEA's, including catalyst and gas diffusion layer selection and integration; E) Verification that these materials can be made using processes which are scalable to commercial volumes using cost effective methods; F) MEA testing in single cells using realistic automotive testing protocols. This project addresses technical barriers A (Durability) and C (Performance) from the Fuel Cells section of the

  16. Optimisation of the round window opening in cochlear implant surgery in wet and dry conditions: impact on intracochlear pressure changes.

    Science.gov (United States)

    Mittmann, Philipp; Ernst, A; Mittmann, M; Todt, I

    2016-11-01

    To preserve residual hearing in cochlear implant candidates, the atraumatic insertion of the cochlea electrode has become a focus of cochlea implant research. In a previous study, intracochlear pressure changes during the opening of the round window membrane were investigated. In the current study, intracochlear pressure changes during opening of the round window membrane under dry and transfluid conditions were investigated. Round window openings were performed in an artificial cochlear model. Intracochlear pressure changes were measured using a micro-optical pressure sensor, which was placed in the apex. Openings of the round window membrane were performed under dry and wet conditions using a cannula and a diode laser. Statistically significant differences in the intracochlear pressure changes were seen between the different methods used for opening of the round window membrane. Lower pressure changes were seen by opening the round window membrane with the diode laser than with the cannula. A significant difference was seen between the dry and wet conditions. The atraumatic approach to the cochlea is assumed to be essential for the preservation of residual hearing. Opening of the round window under wet conditions produce a significant advantage on intracochlear pressure changes in comparison to dry conditions by limiting negative outward pressure.

  17. Behavioral and life history responses to extreme climatic conditions: Studies on a migratory songbird

    Institute of Scientific and Technical Information of China (English)

    A. P. Mφller

    2011-01-01

    Behavioral responses to environmental change are the mechanisms that allow for rapid phenotypic change preventing temporary or permanent damage and hence preventing reductions in fitness. Extreme climatic events are by definition rare, although they are predicted to increase in amplitude and frequency in the coming years. However, our current knowledge about behavioral responses to such extreme events is scarce. Here I analyze two examples of the effects of extreme weather events on behavior and life history: (1) A comparison of behavior and life history during extremely warm and extremely cold years relative to normal years; and (2) a comparison of behavior before and after the extremely early snowfall in fall 1974 when numerous birds died in the Alps during September-October. Behavioral and life history responses of barn swallows Hirundo rustica to extremely cold and extremely warm years were positively correlated, with particularly large effect sizes in cold years. Extreme mortality in barn swallows during fall migration 1974 in the Alps eliminated more than 40% of the breeding population across large areas in Central and Northern Europe, and this affected first arrival date, changes in timing and extent of reproduction and changes in degree of breeding sociality supposedly as a consequence of correlated responses to selection. Finally, I provide directions for research that will allow us to better understand behavior and life history changes in response to extreme climate change [Current Zoology 57 (3): 351-362,2011].

  18. Behavioral and life history responses to extreme climatic conditions: Studies on a migratory songbird

    Directory of Open Access Journals (Sweden)

    A. P. Møller

    2011-06-01

    Full Text Available Behavioral responses to environmental change are the mechanisms that allow for rapid phenotypic change preventing temporary or permanent damage and hence preventing reductions in fitness. Extreme climatic events are by definition rare, although they are predicted to increase in amplitude and frequency in the coming years. However, our current knowledge about behavioral responses to such extreme events is scarce. Here I analyze two examples of the effects of extreme weather events on behavior and life history: (1 A comparison of behavior and life history during extremely warm and extremely cold years relative to normal years; and (2 a comparison of behavior before and after the extremely early snowfall in fall 1974 when numerous birds died in the Alps during September-October. Behavioral and life history responses of barn swallows Hirundo rustica to extremely cold and extremely warm years were positively correlated, with particularly large effect sizes in cold years. Extreme mortality in barn swallows during fall migration 1974 in the Alps eliminated more than 40% of the breeding population across large areas in Central and Northern Europe, and this affected first arrival date, changes in timing and extent of reproduction and changes in degree of breeding sociality supposedly as a consequence of correlated responses to selection. Finally, I provide directions for research that will allow us to better understand behavior and life history changes in response to extreme climate change [Current Zoology 57 (3: 351–362, 2011].

  19. Tribological Behavior of Babbitt Alloy Rubbing Against Si3N4 and Steel Under Dry Friction Condition

    Science.gov (United States)

    Ji, Xianbing; Chen, Yinxia

    2016-03-01

    The tribological behavior of Babbitt alloy rubbing with Si3N4 ball and steel ball with various sliding speeds at dry friction condition was investigated. It was found that B88 alloy rubbing with Si3N4 ball and steel ball possesses a low sliding wear resistance at dry friction. The wear rate is above 10-4 mm3/Nm, and the friction coefficient is from 0.2 to 0.4. At low sliding speed of 0.05-0.1 m/s, the mainly wear mechanisms are microgroove and fatigue wear, while at high sliding speed of 0.5 m/s, the wear mechanisms depend on plastic deformation and delamination. The high wear rate indicates that it is needed to prevent Babbitt alloy from working at dry friction conditions, while the low friction coefficient suggests that it is not easy to the occurrence of cold weld.

  20. A Study on Extremely Dry and Wet Summer Monsoon in Pakistan by Focusing on the Anomalous States of the Upper Troposphere

    Science.gov (United States)

    Ahmad, S.; Koike, T.; Nishii, K.

    2012-04-01

    Seasonally-changes in wind pattern, monsoon, sometimes results in severe droughts and intense flooding in many parts of the world including South Asian countries like Pakistan. The livelihood of a vast population in Pakistan depends on agriculture and land use is strongly influenced by water-based ecosystems that depend on the monsoon rains. Furthermore, climate change studies undertaken so far reveal that action is essential in order to prevent long term damage to water cycle and thus of great concern to the community and stakeholders. Pakistan Summer Monsoon (PSM) is generally affected by both the disturbances from the tropical and the extratropical regions; however there is lack of understanding of physical mechanisms of PSM compared to other regional studies i.e. Indian Summer Monsoon (ISM) and South-East Asian Monsoon (SEAM). In our study, we applied heat and vorticity budgets and wave train analysis to reveal the mechanisms of the extremely dry and wet PSM events associated with the anomalous upper tropospheric circulation. We found that the extremely dry (wet) PSM events are closely related with the strengthening(weakening) of the upper-tropospheric central Asian high. We also found that in addition to Rossby-wave (Matsuno-Gill) type atmospheric response, the Rossby wave train along the Asian Jet originating from northwestern Europe or North Atlantic Ocean strengthened(weakened) the upper-tropospheric central Asian high. Therefore strong convection anomalies resulting in severe flooding (drought) events over the PSM region are induced by both the tropical and extratropical processes. Key Words: Pakistan, Extremes Monsoon Events, Physical Processes, Heat Budget, Vorticity, Wave Train

  1. Optimization of freeze-drying condition of amikacin solid lipid nanoparticles using D-optimal experimental design.

    Science.gov (United States)

    Varshosaz, Jaleh; Ghaffari, Solmaz; Khoshayand, Mohammad Reza; Atyabi, Fatemeh; Dehkordi, Abbas Jafarian; Kobarfard, Farzad

    2012-01-01

    Amikacin as an aminoglycoside antibiotic was chosen to be loaded in a cholesterol carrier with nanoparticle size and sustained release profile to increase the dose interval of amikacin and reduce side-effects. To support the stability of solid lipid nanoparticles (SLNs), freeze-drying was suggested. Factors affecting the freeze-drying process in the present study included the type and concentration of cryoprotectants. Pre-freezing temperature effects were also studied on particle size of SLNs of amikacin. In some preliminary experiments, important factors which influenced the particle size of SLNs after lyophilization were selected and a D-optimal design was applied to optimize the freeze-drying conditions in the production of SLNs with minimum particle size growth after freeze-drying. Zeta potential, DSC thermograms, release profiles and morphology of the optimized particles were studied before and after freeze-drying. Results showed sucrose changed the particle size of SLNs of amikacin from 149 ± 4 nm to 23.9 ± 16.7 nm; in that situation, the absolute value of zeta potential changed from 1 ± 0.7 mV to 13 ± 4 mV. The release profiles showed a sustained release behavior of the loaded drug that did not change significantly before and after freeze-drying, but a burst effect was seen after it in the first 2 h. DSC analysis showed chemical interaction between amikacin and cholesterol.

  2. Surf zone, infragravity wave energy flux, and runup in extreme conditions

    Science.gov (United States)

    Fiedler, J. W.; Brodie, K. L.; McNinch, J.; Guza, R. T.

    2014-12-01

    Waves, currents, and sand levels were observed on a 1.4 km-long cross-shore transect extending from the back beach to ~11 m water depth at Agate Beach, Oregon in Fall 2013. Wave runup and water table fluctuations on this low slope (1:80) beach were measured with a cliff-mounted scanning Lidar and buried pressure sensors. Significant wave heights at an offshore buoy in 128m depth ranged from small (0.5m) to extreme (7.5m), with peak periods between 4-22 seconds. Infragravity frequency (nominally 0.01 Hz) horizontal runup excursions exceeded 100m, and infragravity cross-shore velocity exceeded 3 m/s. Cross-shore patterns of infragravity wave energy flux, observed with seven co-located pressure and current meters, indicate 'proto-saturation' of the inner surfzone in extreme conditions. That is, the intensification of incident wave forcing (e.g. higher energy, longer swell) leads to a wider surfzone and an increase in the shoreward infragravity wave energy seaward of the surfzone, but produces more modest increases in flux in the inner surfzone, and in the runup. Nonlinear energy balances, based on the observations, show transfer of energy from sea-swell to infragravity waves, and vice-versa. The infragravity energy balance closes in cases with low energy incident sea-swell. With more energetic incident waves, there is an unexplained inner surfzone energy sink at the lowest IG frequencies (0.004-0.02 Hz). Ongoing work aims to quantify the effect on infragravity energy balances by infragravity wave breaking and bottom friction. Additionally, the estimates may be degraded by contamination with rotational velocities of surfzone eddies. Whatever the dynamical explanation, infragravity wave runup on a low slope beach in high-energy conditions is limited significantly by dissipation. The slow rate of runup increase suggests nascent, or 'proto' saturation. This work was supported by the U.S. Army Corps of Engineers.

  3. Behavioral and life history responses to extreme climatic conditions: Studies on a migratory songbird

    OpenAIRE

    2011-01-01

    Behavioral responses to environmental change are the mechanisms that allow for rapid phenotypic change preventing temporary or permanent damage and hence preventing reductions in fitness. Extreme climatic events are by definition rare, although they are predicted to increase in amplitude and frequency in the coming years. However, our current knowledge about behavioral responses to such extreme events is scarce. Here I analyze two examples of the effects of extreme weather events on behavior ...

  4. Comparative analysis of aluminium surface roughness in end-milling under dry and minimum quantity lubrication (MQL conditions

    Directory of Open Access Journals (Sweden)

    Okonkwo Ugochukwu C.

    2015-01-01

    Full Text Available In this study an experimental investigation of effects of cutting parameters on surface roughness during end milling of aluminium 6061 under dry condition and minimum quantity lubrication (MQL condition were carried out. Spindle speed (N, feed rate (f, axial depth of cut (a and radial depth of cut (r were cutting parameters chosen as input variables in the investigation of the surface roughness quality. The experimental design adopted for this study was the central composite design (CCD of response surface methodology. Thirty samples were run in a CNC milling machine for each condition and the surface roughness measured using Mitutoyo surface tester. A comparison showing the effects of cutting parameters on the surface roughness for dry and MQL conditions in end-milling of aluminium were evaluated. Surface roughness values for MQL condition were lower with up to 20% reduction when compared to dry conditions. MQL cutting condition was found to be better and more reliable because it is environmentally friendly and gives better surface finish. With the obtained optimum input parameters for surface roughness, production operations will be enhanced.

  5. Numerical Computation of Electric Field and Potential Along Silicone Rubber Insulators Under Contaminated and Dry Band Conditions

    Science.gov (United States)

    Arshad; Nekahi, A.; McMeekin, S. G.; Farzaneh, M.

    2016-09-01

    Electrical field distribution along the insulator surface is considered one of the important parameters for the performance evaluation of outdoor insulators. In this paper numerical simulations were carried out to investigate the electric field and potential distribution along silicone rubber insulators under various polluted and dry band conditions. Simulations were performed using commercially available simulation package Comsol Multiphysics based on the finite element method. Various pollution severity levels were simulated by changing the conductivity of pollution layer. Dry bands of 2 cm width were inserted at the high voltage end, ground end, middle part, shed, sheath, and at the junction of shed and sheath to investigate the effect of dry band location and width on electric field and potential distribution. Partial pollution conditions were simulated by applying pollution layer on the top and bottom surface respectively. It was observed from the simulation results that electric field intensity was higher at the metal electrode ends and at the junction of dry bands. Simulation results showed that potential distribution is nonlinear in the case of clean and partially polluted insulator and linear for uniform pollution layer. Dry band formation effect both potential and electric field distribution. Power dissipated along the insulator surface and the resultant heat generation was also studied. The results of this study could be useful in the selection of polymeric insulators for contaminated environments.

  6. The Effectiveness of Trigger Point Dry Needling for Musculoskeletal Conditions by Physical Therapists: A Systematic Review and Meta-analysis.

    Science.gov (United States)

    Gattie, Eric; Cleland, Joshua A; Snodgrass, Suzanne

    2017-03-01

    Study Design Systematic review and meta-analysis. Background An increasing number of physical therapists in the United States and throughout the world are using dry needling to treat musculoskeletal pain. Objective To examine the short- and long-term effectiveness of dry needling delivered by a physical therapist for any musculoskeletal pain condition. Methods Electronic databases were searched. Eligible randomized controlled trials included those with human subjects who had musculoskeletal conditions that were treated with dry needling performed by a physical therapist, compared with a control or other intervention. The overall quality of the evidence was assessed using the Grading of Recommendations Assessment, Development and Evaluation. Results The initial search returned 218 articles. After screening, 13 were included. Physiotherapy Evidence Database quality scale scores ranged from 4 to 9 (out of a maximum score of 10), with a median score of 7. Eight meta-analyses were performed. In the immediate to 12-week follow-up period, studies provided evidence that dry needling may decrease pain and increase pressure pain threshold when compared to control/sham or other treatment. At 6 to 12 months, dry needling was favored for decreasing pain, but the treatment effect was not statistically significant. Dry needling, when compared to control/sham treatment, provides a statistically significant effect on functional outcomes, but not when compared to other treatments. Conclusion Very low-quality to moderate-quality evidence suggests that dry needling performed by physical therapists is more effective than no treatment, sham dry needling, and other treatments for reducing pain and improving pressure pain threshold in patients presenting with musculoskeletal pain in the immediate to 12-week follow-up period. Low-quality evidence suggests superior outcomes with dry needling for functional outcomes when compared to no treatment or sham needling. However, no difference in

  7. 360⁰ -View of Quantum Theory and Ab Initio Simulation at Extreme Conditions: 2014 Sanibel Symposium

    Energy Technology Data Exchange (ETDEWEB)

    Cheng, Hai-Ping [Univ. of Florida, Gainesville, FL (United States)

    2016-09-02

    The Sanibel Symposium 2014 was held February 16-21, 2014, at the King and Prince, St. Simons Island, GA. It was successful in bringing condensed-matter physicists and quantum chemists together productively to drive the emergence of those specialties. The Symposium had a significant role in preparing a whole generation of quantum theorists. The 54th Sanibel meeting looked to the future in two ways. We had 360⁰-View sessions to honor the exceptional contributions of Rodney Bartlett (70), Bill Butler (70), Yngve Öhrn (80), Fritz Schaefer (70), and Malcolm Stocks (70). The work of these five has greatly impacted several generations of quantum chemists and condensed matter physicists. The “360⁰” is the sum of their ages. More significantly, it symbolizes a panoramic view of critical developments and accomplishments in theoretical and computational chemistry and physics oriented toward the future. Thus, two of the eight 360⁰-View sessions focused specifically on younger scientists. The 360⁰-View program was the major component of the 2014 Sanibel meeting. Another four sessions included a sub-symposium on ab initio Simulations at Extreme Conditions, with focus on getting past the barriers of present-day Born-Oppenheimer molecular dynamics by advances in finite-temperature density functional theory, orbital-free DFT, and new all-numerical approaches.

  8. Smell-taste dysfunctions in extreme weight/eating conditions: analysis of hormonal and psychological interactions.

    Science.gov (United States)

    Fernández-Aranda, Fernando; Agüera, Zaida; Fernández-García, Jose C; Garrido-Sanchez, Lourdes; Alcaide-Torres, Juan; Tinahones, Francisco J; Giner-Bartolomé, Cristina; Baños, Rosa M; Botella, Cristina; Cebolla, Ausias; de la Torre, Rafael; Fernández-Real, Jose M; Ortega, Francisco J; Frühbeck, Gema; Gómez-Ambrosi, Javier; Granero, Roser; Islam, Mohamed A; Jiménez-Murcia, Susana; Tárrega, Salomé; Menchón, José M; Fagundo, Ana B; Sancho, Carolina; Estivill, Xavier; Treasure, Janet; Casanueva, Felipe F

    2016-02-01

    (1) The objective of this study is to analyze differences in smell-taste capacity between females in extreme weight/eating conditions (EWC) and (2) to explore the interaction between smell/taste capacity, gastric hormones, eating behavior and body mass index (BMI). The sample comprised 239 females in EWC [64 Anorexia nervosa (AN) and 80 age-matched healthy-weight controls, and 59 obese and 36 age-matched healthy-weight controls]. Smell and taste assessments were performed through "Sniffin' Sticks" and "Taste Strips," respectively. The assessment measures included the eating disorders inventory-2, the symptom check list 90-revised, and The Dutch Eating Behavior Questionnaire, as well as peptides from the gastrointestinal tract [Ghrelin, peptide YY, cholecystokinin]. Smell capacity was differentially associated across EWC groups. Smell was clearly impaired in obese participants and increased in AN (hyposmia in Obesity was 54.3 and 6.4 % in AN), but taste capacity did not vary across EWC. Ghrelin levels were significantly decreased in obese subjects and were related to smell impairment. EWC individuals showed a distinct smell profile and circulating ghrelin levels compared to controls. Smell capacity and ghrelin may act as moderators of emotional eating and BMI.

  9. Modified and double-clad large mode-area leakage channel fibers for extreme temperature conditions

    Science.gov (United States)

    Thavasi Raja, G.; Varshney, Shailendra K.

    2015-03-01

    Recently large-mode-area hybrid leakage channel fibers (HLCFs) were reported to overcome the limitation on mode area with single-mode (SM) operation for the practical bending radius of 7.5 cm at the preferred wavelength of 1064 nm. In this paper, we present the effects of a thermally induced refractive index change on the mode area of bend-compensated extremely LMA modified HLCFs (M-HLCFs) and double-clad M-HLCFs. A full-vectorial finite-element method-based modal solver is used to obtain the modal characteristics of M-HLCFs in various heat load conditions. Numerical simulations reveal that the effective mode area of M-HLCFs is ˜1433 μm2 at room temperature, which marginally decreases to ˜1387 μm2 while SM operation is maintained when the temperature distribution rises to ˜125 °C over the fiber geometry during high-power operations. We have also investigated a double-clad M-HLCF design exhibiting a mode area > ˜ 1000 μm2 for all heat load density variations up to a maximum of 12 × 109 W m-3, corresponding to a 250 °C temperature in the center of the fiber core region.

  10. 360⁰ -View of Quantum Theory and Ab Initio Simulation at Extreme Conditions: 2014 Sanibel Symposium

    Energy Technology Data Exchange (ETDEWEB)

    Cheng, Hai-Ping [Univ. of Florida, Gainesville, FL (United States)

    2016-09-02

    The Sanibel Symposium 2014 was held February 16-21 2014 at the King and Prince, St. Simons Island, GA. It was successful in bringing condensed-matter physicists and quantum chemists together productively to drive the emergence of those specialties. The Symposium had a significant role in preparing a whole generation of quantum theorists. The 54th Sanibel meeting looked to the future in two ways. We had 360⁰-View sessions to honor the exceptional contributions of Rodney Bartlett (70), Bill Butler (70), Yngve Öhrn (80), Fritz Schaefer (70), and Malcolm Stocks (70). The work of these five has greatly impacted several generations of quantum chemists and condensed matter physicists. The “360⁰” is the sum of their ages. More significantly, it symbolizes a panoramic view of critical developments and accomplishments in theoretical and computational chemistry and physics oriented toward the future. Thus, two of the eight 360⁰-View sessions focused specifically on younger scientists. The 360⁰-View program was the major component of the 2014 Sanibel meeting. Another four sessions included a sub-symposium on ab initio Simulations at Extreme Conditions, with focus on getting past the barriers of present-day Born-Oppenheimer molecular dynamics by advances in finite-temperature density functional theory, orbital-free DFT, and new all-numerical approaches.

  11. Effect of environmental factors on body condition score of Taggar goats under dry land farming in western Sudan

    Directory of Open Access Journals (Sweden)

    I. Bushara

    2011-09-01

    Full Text Available Effects of type of supplementation, season of kidding and litter size on body condition score (BCS at kidding and at weaning time were evaluated in Taggar goats in extensive management under dry land farm. The supplemented groups (2 and 3 had (P0.05 for higher BCS at kidding compared with single and triplet kidders. At weaning time triplets kidder had slightly lower (P<0.05 body condition compared to single and twin kidders.

  12. Effects of reclaimed asphalt pavement on indirect tensile strength test of foamed asphalt mix tested in dry condition

    Science.gov (United States)

    Yati Katman, Herda; Rasdan Ibrahim, Mohd; Yazip Matori, Mohd; Norhisham, Shuhairy; Ismail, Norlela

    2013-06-01

    Indirect tensile strength (ITS) test was conducted to analyse strength of the foamed asphalt mixes incorporating reclaimed asphalt pavement. Samples were tested for ITS after cured in the oven at 40°C for 72 hours. This testing condition known as dry condition or unconditioned. Laboratory results show that reclaimed asphalt pavement (RAP) contents insignificantly affect the ITS results. ITS results significantly affected by foamed bitumen contents.

  13. Characterization of Extremely Low Frequency Magnetic Fields from Diesel, Gasoline and Hybrid Cars under Controlled Conditions

    Directory of Open Access Journals (Sweden)

    Ronen Hareuveny

    2015-01-01

    Full Text Available This study characterizes extremely low frequency (ELF magnetic field (MF levels in 10 car models. Extensive measurements were conducted in three diesel, four gasoline, and three hybrid cars, under similar controlled conditions and negligible background fields. Averaged over all four seats under various driving scenarios the fields were lowest in diesel cars (0.02 μT, higher for gasoline (0.04–0.05 μT and highest in hybrids (0.06–0.09 μT, but all were in-line with daily exposures from other sources. Hybrid cars had the highest mean and 95th percentile MF levels, and an especially large percentage of measurements above 0.2 μT. These parameters were also higher for moving conditions compared to standing while idling or revving at 2500 RPM and higher still at 80 km/h compared to 40 km/h. Fields in non-hybrid cars were higher at the front seats, while in hybrid cars they were higher at the back seats, particularly the back right seat where 16%–69% of measurements were greater than 0.2 μT. As our results do not include low frequency fields (below 30 Hz that might be generated by tire rotation, we suggest that net currents flowing through the cars’ metallic chassis may be a possible source of MF. Larger surveys in standardized and well-described settings should be conducted with different types of vehicles and with spectral analysis of fields including lower frequencies due to magnetization of tires.

  14. Structural and Mechanical Properties of Intermediate Filaments under Extreme Conditions and Disease

    Science.gov (United States)

    Qin, Zhao

    Intermediate filaments are one of the three major components of the cytoskeleton in eukaryotic cells. It was discovered during the recent decades that intermediate filament proteins play key roles to reinforce cells subjected to large-deformation as well as participate in signal transduction. However, it is still poorly understood how the nanoscopic structure, as well as the biochemical properties of these protein molecules contribute to their biomechanical functions. In this research we investigate the material function of intermediate filaments under various extreme mechanical conditions as well as disease states. We use a full atomistic model and study its response to mechanical stresses. Learning from the mechanical response obtained from atomistic simulations, we build mesoscopic models following the finer-trains-coarser principles. By using this multiple-scale model, we present a detailed analysis of the mechanical properties and associated deformation mechanisms of intermediate filament network. We reveal the mechanism of a transition from alpha-helices to beta-sheets with subsequent intermolecular sliding under mechanical force, which has been inferred previously from experimental results. This nanoscale mechanism results in a characteristic nonlinear force-extension curve, which leads to a delocalization of mechanical energy and prevents catastrophic fracture. This explains how intermediate filament can withstand extreme mechanical deformation of > 1 00% strain despite the presence of structural defects. We combine computational and experimental techniques to investigate the molecular mechanism of Hutchinson-Gilford progeria syndrome, a premature aging disease. We find that the mutated lamin tail .domain is more compact and stable than the normal one. This altered structure and stability may enhance the association of intermediate filaments with the nuclear membrane, providing a molecular mechanism of the disease. We study the nuclear membrane association

  15. Physiological Responses to Firefighting in Extreme Temperatures Do Not Compare to Firefighting in Temperate Conditions

    Directory of Open Access Journals (Sweden)

    Stephanie Windisch

    2017-08-01

    Full Text Available Purpose: The aim of this study was to examine physiological responses to two different simulated firefighting exercises: a firefighting exercise with flashovers, smoke, poor visibility and extreme temperatures (300° in a burning container and a standard firefighting exercise in temperate conditions. Furthermore, a second purpose of the study was to find out if the contribution of strength and endurance capacities to firefighting performance changes when the demands of the firefighting exercise change.Methods: Sixteen professional firefighters performed a maximum treadmill test, strength testing, a standard simulated firefighting exercise (SFE without heat and flashovers and a firefighting exercise with a simulation of the flashover phenomenon in a burning container (FOT. The treadmill testing was used to determine peak oxygen uptake (VO2peak, ventilatory threshold (VT1 and respiratory compensation point (RCP. Three intensity zones were identified according to heart rate (HR values corresponding to VT1 and RCP: zone 1–HR below VT1, zone 2-HR between VT1 and RCP, zone 3–HR above RCP. Firefighting performance was determined by a simple time-strain-air depletion model (TSA taking the sum of z-transformed parameters of time to finish the exercise, strain in terms of mean heart rate, and air depletion from the breathing apparatus. Correlations were then established between TSA based firefighting performance parameters and fitness variables representing strength and endurance.Results: HR was significantly lower during SFE (79.9 ± 6.9%HRmax compared to FOT (85.4 ± 5.2%HRmax. During SFE subjects spent 24.6 ± 30.2% of time in zone 1, 65.8 ± 28.1% in zone 2 and 9.7 ± 16.6% in zone 3. During FOT subjects spent 16.3 ± 12.8% in zone 1, 50.4 ± 13.2% in zone 2 and 33.3 ± 16.6% in zone 3. Out of all correlations, relative VO2peak showed the highest relation to mean HR during SFE (−0.593 as well as FOT (−0.693.Conclusions: Endurance in terms of

  16. Dry/Wet Conditions Monitoring Based on TRMM Rainfall Data and Its Reliability Validation over Poyang Lake Basin, China

    Directory of Open Access Journals (Sweden)

    Xianghu Li

    2013-11-01

    Full Text Available Local dry/wet conditions are of great concern in regional water resource and floods/droughts disaster risk management. Satellite-based precipitation products have greatly improved their accuracy and applicability and are expected to offer an alternative to ground rain gauges data. This paper investigated the capability of Tropical Rainfall Measuring Mission (TRMM rainfall data for monitoring the temporal and spatial variation of dry/wet conditions in Poyang Lake basin during 1998–2010, and validated its reliability with rain gauges data from 14 national meteorological stations in the basin. The results show that: (1 the daily TRMM rainfall data does not describe the occurrence and contribution rates of precipitation accurately, but monthly TRMM data have a good linear relationship with rain gauges rainfall data; (2 both the Z index and Standardized Precipitation Index (SPI based on monthly TRMM rainfall data oscillate around zero and show a consistent interannual variability as compared with rain gauges data; (3 the spatial pattern of moisture status, either in dry months or wet months, based on both the Z index and SPI using TRMM data, agree with the observed rainfall. In conclusion, the monthly TRMM rainfall data can be used for monitoring the variation and spatial distribution of dry/wet conditions in Poyang Lake basin.

  17. A Combination of Extreme Environmental Conditions Favor the Prevalence of Endospore-Forming Firmicutes

    Science.gov (United States)

    Filippidou, Sevasti; Wunderlin, Tina; Junier, Thomas; Jeanneret, Nicole; Dorador, Cristina; Molina, Veronica; Johnson, David R.; Junier, Pilar

    2016-01-01

    Environmental conditions unsuitable for microbial growth are the rule rather than the exception in most habitats. In response to this, microorganisms have developed various strategies to withstand environmental conditions that limit active growth. Endospore-forming Firmicutes (EFF) deploy a myriad of survival strategies in order to resist adverse conditions. Like many bacterial groups, they can form biofilms and detect nutrient scarcity through chemotaxis. Moreover, within this paraphyletic group of Firmicutes, ecophysiological optima are diverse. Nonetheless, a response to adversity that delimits this group is the formation of wet-heat resistant spores. These strategies are energetically demanding and therefore might affect the biological success of EFF. Therefore, we hypothesize that abundance and diversity of EFF should be maximized in those environments in which the benefits of these survival strategies offsets the energetic cost. In order to address this hypothesis, geothermal and mineral springs and drillings were selected because in these environments of steep physicochemical gradients, diversified survival strategies may become a successful strategy.We collected 71 samples from geothermal and mineral environments characterized by none (null), single or multiple limiting environmental factors (temperature, pH, UV radiation, and specific mineral composition). To measure success, we quantified EFF gene copy numbers (GCN; spo0A gene) in relation to total bacterial GCN (16S rRNA gene), as well as the contribution of EFF to community composition. The quantification showed that relative GCN for EFF reached up to 20% at sites characterized by multiple limiting environmental factors, whereas it corresponded to less than 1% at sites with one or no limiting environmental factor. Pyrosequencing of the 16S rRNA gene supports a higher contribution of EFF at sites with multiple limiting factors. Community composition suggested a combination of phylotypes for which active

  18. A combination of extreme environmental conditions favor the prevalence of Endospore-forming Firmicutes

    Directory of Open Access Journals (Sweden)

    Sevasti Filippidou

    2016-11-01

    Full Text Available Environmental conditions unsuitable for microbial growth are the rule rather than the exception in most habitats. In response to this, microorganisms have developed various strategies to withstand environmental conditions that limit active growth. Endospore-forming Firmicutes (EFF deploy a myriad of survival strategies in order to resist adverse conditions. Like many bacterial groups, they can form biofilms and detect nutrient scarcity through chemotaxis. Moreover, within this paraphyletic group of Firmicutes, ecophysiological optima are diverse. Nonetheless, a response to adversity that delimits this group is the formation of wet-heat resistant spores. These strategies are energetically demanding and therefore might affect the biological success of EFF. Therefore, we hypothesize that abundance and diversity of EFF should be maximized in those environments in which the benefits of these survival strategies offsets the energetic cost. In order to address this hypothesis, geothermal and mineral springs and drillings were selected because in these environments of steep physicochemical gradients, diversified survival strategies may become a successful strategy. We collected 71 samples from geothermal and mineral environments characterized by none (null, single or multiple limiting environmental factors (temperature, pH, UV radiation and specific mineral composition. To measure success, we quantified EFF gene copy numbers (GCN; spo0A gene in relation to total bacterial GCN (16S rRNA gene, as well as the contribution of EFF to community composition. The quantification showed that relative GCN for EFF reached up to 20% at sites characterized by multiple limiting environmental factors, whereas it corresponded to less than 1% at sites with one or no limiting environmental factor. Pyrosequencing of the 16S rRNA gene supports a higher contribution of EFF at sites with multiple limiting factors. Community composition suggested a combination of phylotypes

  19. XBeach-G: a tool for predicting gravel barrier response to extreme storm conditions

    Science.gov (United States)

    Masselink, Gerd; Poate, Tim; McCall, Robert; Roelvink, Dano; Russell, Paul; Davidson, Mark

    2014-05-01

    Gravel beaches protect low-lying back-barrier regions from flooding during storm events and their importance to society is widely acknowledged. Unfortunately, breaching and extensive storm damage has occurred at many gravel sites and this is likely to increase as a result of sea-level rise and enhanced storminess due to climate change. Limited scientific guidance is currently available to provide beach managers with operational management tools to predict the response of gravel beaches to storms. The New Understanding and Prediction of Storm Impacts on Gravel beaches (NUPSIG) project aims to improve our understanding of storm impacts on gravel coastal environments and to develop a predictive capability by modelling these impacts. The NUPSIG project uses a 5-pronged approach to address its aim: (1) analyse hydrodynamic data collected during a proto-type laboratory experiment on a gravel beach; (2) collect hydrodynamic field data on a gravel beach under a range of conditions, including storm waves with wave heights up to 3 m; (3) measure swash dynamics and beach response on 10 gravel beaches during extreme wave conditions with wave heights in excess of 3 m; (4) use the data collected under 1-3 to develop and validate a numerical model to model hydrodynamics and morphological response of gravel beaches under storm conditions; and (5) develop a tool for end-users, based on the model formulated under (4), for predicting storm response of gravel beaches and barriers. The aim of this presentation is to present the key results of the NUPSIG project and introduce the end-user tool for predicting storm response on gravel beaches. The model is based on the numerical model XBeach, and different forcing scenarios (wave and tides), barrier configurations (dimensions) and sediment characteristics are easily uploaded for model simulations using a Graphics User Interface (GUI). The model can be used to determine the vulnerability of gravel barriers to storm events, but can also be

  20. Cold-water coral growth under extreme environmental conditions, the Cape Lookout area, NW Atlantic

    Science.gov (United States)

    Mienis, F.; Duineveld, G. C. A.; Davies, A. J.; Lavaleye, M. M. S.; Ross, S. W.; Seim, H.; Bane, J.; van Haren, H.; Bergman, M. J. N.; de Haas, H.; Brooke, S.; van Weering, T. C. E.

    2014-05-01

    day, which is the largest temperature variability as measured so far in a cold-water coral habitat. Warm events, related to Gulf Stream meanders, had the duration of roughly 1 week and the current during these events was directed to the NNE. The consequences of such events must be significant given the strong effects of temperature on the metabolism of cold-water corals. Furthermore, elevated acoustic backscatter values and high mass fluxes were also recorded during these events, indicating a second stressor that may affect the corals. The abrasive nature of sand in combination with strong currents might sand blast the corals. We conclude that cold-water corals near Cape Lookout live under extreme conditions that limit mound growth at present.

  1. Influence of product thickness, chamber pressure and heating conditions on production rate of freeze-dried yoghurt

    Energy Technology Data Exchange (ETDEWEB)

    Sharma, N.K. [G.B. Pant Univ., of Agriculture and Technology (India). Dept. of Mechanical Engineering; Arora, C.P. [Indian Inst. of Tech., New Delhi (India)

    1995-06-01

    The effects of product thickness, chamber pressure and heating conditions on product temperature profiles and production rate of freeze-dried yoghurt were investigated experimentally. Three sample thicknesses - 3.8 mm, 6.2 mm and 9.4 mm - were tested at chamber pressures of 0.01 and 0.5 mmHg. The production rate increased by decreasing product thickness in contact heating through the bottom of the frozen layer, whereas no significant change was observed in radiant heating. A reduction in chamber pressure from 0.50 to 0.01 mmHg increased the drying time in radiant heating. Maximum production rate was obtained when the thickness of dried product was 6.2 mm, when heat was transferred simultaneously through the frozen and dried layers, and the chamber pressure was at 0.01 mmHg. Use of the product tray developed in this study prevents the growth of dry layers at the contact surfaces. (Author)

  2. Experimental investigation of convective drying kinetics of kiwi under different conditions

    Science.gov (United States)

    Darıcı, Selçuk; Şen, Soner

    2015-08-01

    The effects of air temperature, velocity and humidity on drying characteristics of kiwi are experimentally investigated for the temperatures in the range of 50-80 °C, of the velocities 0.5-2.0 m/s, of the relative humidity values of 5-20 % and for two slice thicknesses. It is observed that there is a very close agreement between the model of Midilli et al. (Dry Technol 20:1503-1513, 2002) and the present study with coefficients of correlation R2 of 0.9949-0.9996.

  3. Secondary Organic Aerosol formation from isoprene photooxidation under dry conditions (CUMULUS project)

    Science.gov (United States)

    Brégonzio-Rozier, Lola; Siekmann, Frank; Giorio, Chiara; Temime-Roussel, Brice; Pangui, Edouard; Morales, Sébastien; Gratien, Aline; Ravier, Sylvain; Monod, Anne; Doussin, Jean-Francois

    2014-05-01

    Isoprene (2-methyl-1,3-butadiene, C5H8) is one of the most abundant non-methane hydrocarbons emitted into the troposphere. Its annual global emission has recently been estimated in the range of 440 to 660 TgC (Guenther et al., 2006). Because of its large concentrations and high reactivity with the hydroxyl radical (OH), isoprene can have a strong influence on tropospheric photochemistry. It has been determined recently that isoprene also plays a role in secondary organic aerosol (SOA) formation in the ambient atmosphere even if isoprene leads to low SOA yields. The aim of the present work was to study isoprene photo-oxidation with OH radical in order to investigate its oxidation products and resulting aerosol production. A special care was taken to the realism of the experiment: light source, NOx and OH levels and aging time (around 10 hours). Experiments were performed in the CESAM chamber (Wang et al., 2011) which was designed to investigate multiphase processes under realistic actinic flux, and accurate control of temperature. In each experiment, around 800 ppb of isoprene was injected in the chamber together with the OH source under dry conditions (FTIR), a Proton Transfer Reaction Mass Spectrometer (PTR-TOF-MS) and NOx and ozone analyzers. A Scanning Mobility Particle Sizer (SMPS) and an Aerodyne High Resolution Time-Of-Flight Aerosol Mass Spectrometer (HR-TOF-AMS) were also used to investigate SOA formation and composition. In all experiments, we noted a SOA production at the end of isoprene oxidation i.e. exhibiting a clear secondary products type growth. Several results (including SOA densities and yields, and O/C ratios) were obtained using SMPS and AMS data allowing us to characterize SOA formation and composition during the experiments. The characterization of the gaseous and particulate phases will be presented. While the SOA yields in the literature exhibit a general dispersion, the SOA yields obtained during the experiments are consistent with the

  4. Complex layered dental restorations: Are they recognizable and do they survive extreme conditions?

    Science.gov (United States)

    Soon, Alistair S; Bush, Mary A; Bush, Peter J

    2015-09-01

    Recent research has shown that restorative dental materials can be recognized by microscopy and elemental analysis (scanning electron microscopy/energy dispersive X-ray spectroscopy and X-ray fluorescence; SEM/EDS and XRF) and that this is possible even in extreme conditions, such as cremation. These analytical methods and databases of dental materials properties have proven useful in DVI (disaster victim identification) of a commercial plane crash in 2009, and in a number of other victim identification cases. Dental materials appear on the market with ever expanding frequency. With their advent, newer methods of restoration have been proposed and adopted in the dental office. Methods might include placing multiple layers of dental materials, where they have different properties including adhesion, viscosity, or working time. These different dental materials include filled adhesives, flowable resins, glass ionomer cements, composite resins, liners and sealants. With possible combinations of different materials in these restorations, the forensic odontologist is now confronted with a new difficulty; how to recognize each individual material. The question might be posed if it is even possible to perform this task. Furthermore, an odontologist might be called upon to identify a victim under difficult circumstances, such as when presented with fragmented or incinerated remains. In these circumstances the ability to identify specific dental materials could assist in the identification of the deceased. Key to use of this information is whether these new materials and methods are detailed in the dental chart. Visual or radiographic inspection may not reveal the presence of a restoration, let alone the possible complex nature of that restoration. This study demonstrates another scientific method in forensic dental identification.

  5. An Invariant-Preserving ALE Method for Solids under Extreme Conditions

    Energy Technology Data Exchange (ETDEWEB)

    Sambasivan, Shiv Kumar [Los Alamos National Laboratory; Christon, Mark A [Los Alamos National Laboratory

    2012-07-17

    We are proposing a fundamentally new approach to ALE methods for solids undergoing large deformation due to extreme loading conditions. Our approach is based on a physically-motivated and mathematically rigorous construction of the underlying Lagrangian method, vector/tensor reconstruction, remapping, and interface reconstruction. It is transformational because it deviates dramatically from traditionally accepted ALE methods and provides the following set of unique attributes: (1) a three-dimensional, finite volume, cell-centered ALE framework with advanced hypo-/hyper-elasto-plastic constitutive theories for solids; (2) a new physically and mathematically consistent reconstruction method for vector/tensor fields; (3) advanced invariant-preserving remapping algorithm for vector/tensor quantities; (4) moment-of-fluid (MoF) interface reconstruction technique for multi-material problems with solids undergoing large deformations. This work brings together many new concepts, that in combination with emergent cell-centered Lagrangian hydrodynamics methods will produce a cutting-edge ALE capability and define a new state-of-the-art. Many ideas in this work are new, completely unexplored, and hence high risk. The proposed research and the resulting algorithms will be of immediate use in Eulerian, Lagrangian and ALE codes under the ASC program at the lab. In addition, the research on invariant preserving reconstruction/remap of tensor quantities is of direct interest to ongoing CASL and climate modeling efforts at LANL. The application space impacted by this work includes Inertial Confinement Fusion (ICF), Z-pinch, munition-target interactions, geological impact dynamics, shock processing of powders and shaped charges. The ALE framework will also provide a suitable test-bed for rapid development and assessment of hypo-/hyper-elasto-plastic constitutive theories. Today, there are no invariant-preserving ALE algorithms for treating solids with large deformations. Therefore

  6. PREFACE: International Symposium on Molecular Conductors: Novel Functions of Molecular Conductors under Extreme Conditions (ISMC 2008)

    Science.gov (United States)

    Takahashi, Toshihiro; Suzumura, Yoshikazu

    2008-02-01

    The International Symposium on Molecular Conductors 2008 (ISMC2008) was held as the second international symposium of the project entitled `Novel Functions of Molecular Conductors under Extreme Conditions', which was supported by the Grant-in-aid for Scientific Research on Priority Areas from the Ministry of Education, Culture, Sports, Science and Technology in Japan. The project lasted from September 2003 to March 2008, and was completed by this symposium held at Okazaki Conference Center, Institute for Molecular Science, Okazaki, Japan (23-25 July 2008), which about 100 scientists attended. During the symposium, five project teams gave summary talks and exciting talks were given on the topics developed recently not only by the members of the project but also by other scientists including invited speakers from abroad, who are doing active research on molecular conductors. It is expected that papers presented in the symposium will give valuable hints for the next step in the research of this field. Therefore the organizers of this symposium decided to publish this proceedings in order to demonstrate these activities, not only for the local community of the project, but also for the broad society of international scientists who are interested in molecular conductors. The editors, who are also the organizers of this symposium, believe that this proceedings provides a significant and relevant contribution to the field of molecular conductors since it is the first time we have published such a proceedings as an electronic journal. We note that all papers published in this volume of Journal of Physics: Conference Series have been peer reviewed by expert referees. Editors made every effort to satisfy the criterion of a proceedings journal published by IOP Publishing. Toshihiro Takahashi and Yoshikazu Suzumura Editors: Toshihiro Takahashi (Gakushuin University) (Chairman) Kazushi Kanoda (University of Tokyo) Seiichi Kagoshima (University of Tokyo) Takehiko Mori (Tokyo

  7. "Rotten Ice": Characterizing the Physical Properties of Arctic Sea Ice Under Conditions of Extreme Summer Melt

    Science.gov (United States)

    Light, B.; Frantz, C. M.; Junge, K.; Orellana, M. V.; Carpenter, S.; Farley, S. M.; Lieb-Lappen, R.; Courville, Z.

    2016-12-01

    The microstructural properties of sea ice are central to understanding the mechanical, thermal, electrical, and optical properties of a sea ice cover. Over the course of an annual cycle, this small scale structure routinely evolves from a network of mostly isolated brine and gas inclusions prevalent in cold ice, to a more connected, more permeable structure as the ice endures summer melt processes. In the case of extreme summer melt, sea ice can become "rotten", and it is expected that such rotten ice may become more prevalent as melt seasons lengthen. Rotten ice is approximately isothermal, largely drained of brine, and is typified by the presence of large multi-cm-scale void spaces that contribute to its high permeability and low structural integrity. These properties are expected to alter the ice cover response to dynamic forcing, ability to backscatter incident light, and its melt rate. An interdisciplinary effort to characterize the physical properties of rotten first-year ice, in concert with some of its chemical and biological properties, is being carried out both in the field and in the laboratory. Time-series samples focusing on the evolution of ice microstructure were acquired and analyzed for shore-fast first-year sea ice near Barrow, Alaska in May - July of 2015. Laboratory studies have focused on assessing the seasonal evolution of optical properties of this ice, as well as the measurement of melt rates of ice grown under carefully controlled laboratory conditions. Preliminary results from these studies illuminate some of the physical and biophysical controls on late summer ice melt.

  8. Executive functions profile in extreme eating/weight conditions: from anorexia nervosa to obesity.

    Directory of Open Access Journals (Sweden)

    Ana B Fagundo

    Full Text Available BACKGROUND: Extreme weight conditions (EWC groups along a continuum may share some biological risk factors and intermediate neurocognitive phenotypes. A core cognitive trait in EWC appears to be executive dysfunction, with a focus on decision making, response inhibition and cognitive flexibility. Differences between individuals in these areas are likely to contribute to the differences in vulnerability to EWC. The aim of the study was to investigate whether there is a common pattern of executive dysfunction in EWC while comparing anorexia nervosa patients (AN, obese subjects (OB and healthy eating/weight controls (HC. METHODS: Thirty five AN patients, fifty two OB and one hundred thirty seven HC were compared using the Wisconsin Card Sorting Test (WCST; Stroop Color and Word Test (SCWT; and Iowa Gambling Task (IGT. All participants were female, aged between 18 and 60 years. RESULTS: There was a significant difference in IGT score (F(1.79; p<.001, with AN and OB groups showing the poorest performance compared to HC. On the WCST, AN and OB made significantly more errors than controls (F(25.73; p<.001, and had significantly fewer correct responses (F(2.71; p<.001. Post hoc analysis revealed that the two clinical groups were not significantly different from each other. Finally, OB showed a significant reduced performance in the inhibition response measured with the Stroop test (F(5.11; p<.001 compared with both AN and HC. CONCLUSIONS: These findings suggest that EWC subjects (namely AN and OB have similar dysfunctional executive profile that may play a role in the development and maintenance of such disorders.

  9. Spray-drying of alumina powder for APS: effect of slurry properties and drying conditions upon particle size and morphology of feedstock

    Indian Academy of Sciences (India)

    Bai Yu; Yang Jian Feng; Lee Soo Wohn; Chen Huang; Yu Fang Li; Zhang Jia

    2011-12-01

    In this paper, effects of variables concerning slurry properties and drying conditions on the particle size and morphology of feedstock were discussed. The results indicated that, the increase of powder loading increased 50 and volume content but reduced recovery rate slightly. Other variables, such as inlet temperature, showed a maximum on the desired property. The particle size of resulting feedstock increased with the rise of feeding rate of slurry, however, decreased with the increase of atomization pressure based on the premise that atomization pressure was enough to force slurry to form the liquid membrane. For preparation of spherical feedstock, optimized variables were as follows: 60 wt.% powder in slurry, 2 wt.% PVA in slurry, inlet temperature of 60°C, atomization pressure of 13 × 103 KPa and feeding rate of 12 ml min-1. The volume content of feedstocks with 10–45 m was above 65% and for 50 it was 15.42 m. In addition, according to the heat and mass transfer equation, the drying mechanism was established, which was well in agreement with the experimental results.

  10. Assessment of hydrological extremes in the basins of Shilka and Argun rivers (Far East of Russia) in changing conditions

    Science.gov (United States)

    Sokolova, Daria; Semenova, Olga; Vinogradova, Tatyana

    2016-04-01

    Eastern Transbaikal region of Russia is formed by the basins of the Argun and Shilka Rivers (the upreaches of the Amur River). This region is simultaneously under the flood and drought hazard threat due to the combination of dry continental climate and monsoon impacts. Observed intensification of extreme hazard events in the region requires the scientific base of development of adaptation and mitigation measures. The aim of the study is the analysis of long-term variability of hydrological characteristics of the region by the means of mathematical statistics and projection of hydrological extremes in changing conditions of climate and landscapes based on hydrological modelling. Our research consisted of two stages. Firstly, we developed the database of observed daily hydrographs for about 50 runoff gauges of the region with average continuous period of observations 50 years (up to 2013) and areas from 12.3 to 200000 km2. Statistical analysis of the data was conducted and the trends of changes were assessed and analyzed. At the second stage we selected four river watersheds as the objects of modelling, namely, the gauging stations at the rivers Zun-Cooka, Gazipur, Borzya and Mogoytuy, ranging in size from 100 to 4000 km2. The basins are characterized by the variety of runoff conditions. Average elevation is about 650 m, hilly plateaus dominate the relief. The landscapes are taiga and forest-steppe with discontinuous permafrost. The climate is continental, annual precipitation varies within the range 200-450 mm, runoff - from 30 to 100 mm. The objectives of modelling stage were 1) the estimation of the hydrological model's parameters and its validation at historical data, 2) development of conceptual scenarios of changes of climate and landscapes, 3) running the model in projection mode to assess the implications of possible changes in hydrological regime. High variability of climate and hydrological regime do not allow for conventional modelling procedures to be

  11. Reactivity of Xe with ice at extreme P-T conditions

    Science.gov (United States)

    Sanloup, C.; Hochlaf, M.; Maynard-Casely, H.; Gregoryanz, E.; Mezouar, M.

    2010-12-01

    Water is an important component of terrestrial and giant planets so that any reactivity with Xe at depth would have strong consequences on our knowledge of planetary dynamics as it heavily relies on Xe isotopes geochemistry. The chemistry of ‘noble gas’ have seen fascinating experimental and theoretical advances during the last twenty years as highlighted by review papers (1,2). Noble gas chemistry proceeds essentially by photosynthesis of precursors in a low-temperature noble-gas matrix. The pressure variable has seldom been investigated as a mean to enforce Xe to bond other elements (3). Xe is among the gases that stabilize clathrate hydrates through van der Waals interactions. Xe hydrates are stable up to 2.5 GPa, before dissociating into Xe plus ice VII (4). However, the chemistry of water with solid Xe has been successfully explored by UV photolysis (5,6). Those findings plus our own results on the stability of Xe oxides in the terrestrial crust (7) let us envisage that the chemistry of Xe with oxygen at extreme conditions could be flourishing. We have thus explored the reactivity of Xe with water up to 80 GPa by using a laser-heated diamond-anvil cell combined with in situ x-ray diffraction measurements. Formation of a compound is indeed observed at conditions that could occur in the interiors of ice-rich giant planets Uranus and Neptune. To complement the x-ray diffraction data, ab initio calculations have been carried out to determine the molecular structure of the new found compound. These resuts hence add another example of noble gas sequestration in giant planets, as recently proposed for Ne (8). References: 1. W. Grochala, Chem. Soc. Rev. 1632, 36 (2007). 2. R. B. Gerber, Annu. Rev. Phys. Chem., 55, 55 (2004). 3. A. I. Katz and V. A. Apkarian, J. Phys. Chem., 94, 6671-6678 (1990). 4. C. Sanloup et al., PNAS 99, 25 (2002). 5. M. Pettersson et al., Eur. J. Inorg. Chem. 505, 729 (1999). 6. L. Khriachtchev et al., JACS 130, 6114 (2008). 7. C. Sanloup et

  12. Air-drying of cells, the novel conditions for stimulated synthesis of triacylglycerol in a Green Alga, Chlorella kessleri.

    Directory of Open Access Journals (Sweden)

    Takuma Shiratake

    Full Text Available Triacylglycerol is used for the production of commodities including food oils and biodiesel fuel. Microalgae can accumulate triacylglycerol under adverse environmental conditions such as nitrogen-starvation. This study explored the possibility of air-drying of green algal cells as a novel and simple protocol for enhancement of their triacylglycerol content. Chlorella kessleri cells were fixed on the surface of a glass fibre filter and then subjected to air-drying with light illumination. The dry cell weight, on a filter, increased by 2.7-fold in 96 h, the corresponding chlorophyll content ranging from 1.0 to 1.3-fold the initial one. Concomitantly, the triacylglycerol content remarkably increased to 70.3 mole% of fatty acids and 15.9% (w/w, relative to total fatty acids and dry cell weight, respectively, like in cells starved of nitrogen. Reduction of the stress of air-drying by placing the glass filter on a filter paper soaked in H2O lowered the fatty acid content of triacylglycerol to 26.4 mole% as to total fatty acids. Moreover, replacement of the H2O with culture medium further decreased the fatty acid content of triacylglycerol to 12.2 mole%. It thus seemed that severe dehydration is required for full induction of triacylglycerol synthesis, and that nutritional depletion as well as dehydration are crucial environmental factors. Meanwhile, air-drying of Chlamydomonas reinhardtii cells increased the triacylglycerol content to only 37.9 mole% of fatty acids and 4.8% (w/w, relative to total fatty acids and dry cell weight, respectively, and a marked decrease in the chlorophyll content, on a filter, of 33%. Air-drying thus has an impact on triacylglycerol synthesis in C. reinhardtii also, however, the effect is considerably limited, owing probably to instability of the photosynthetic machinery. This air-drying protocol could be useful for the development of a system for industrial production of triacylglycerol with appropriate selection of the

  13. Air-drying of cells, the novel conditions for stimulated synthesis of triacylglycerol in a Green Alga, Chlorella kessleri.

    Science.gov (United States)

    Shiratake, Takuma; Sato, Atsushi; Minoda, Ayumi; Tsuzuki, Mikio; Sato, Norihiro

    2013-01-01

    Triacylglycerol is used for the production of commodities including food oils and biodiesel fuel. Microalgae can accumulate triacylglycerol under adverse environmental conditions such as nitrogen-starvation. This study explored the possibility of air-drying of green algal cells as a novel and simple protocol for enhancement of their triacylglycerol content. Chlorella kessleri cells were fixed on the surface of a glass fibre filter and then subjected to air-drying with light illumination. The dry cell weight, on a filter, increased by 2.7-fold in 96 h, the corresponding chlorophyll content ranging from 1.0 to 1.3-fold the initial one. Concomitantly, the triacylglycerol content remarkably increased to 70.3 mole% of fatty acids and 15.9% (w/w), relative to total fatty acids and dry cell weight, respectively, like in cells starved of nitrogen. Reduction of the stress of air-drying by placing the glass filter on a filter paper soaked in H2O lowered the fatty acid content of triacylglycerol to 26.4 mole% as to total fatty acids. Moreover, replacement of the H2O with culture medium further decreased the fatty acid content of triacylglycerol to 12.2 mole%. It thus seemed that severe dehydration is required for full induction of triacylglycerol synthesis, and that nutritional depletion as well as dehydration are crucial environmental factors. Meanwhile, air-drying of Chlamydomonas reinhardtii cells increased the triacylglycerol content to only 37.9 mole% of fatty acids and 4.8% (w/w), relative to total fatty acids and dry cell weight, respectively, and a marked decrease in the chlorophyll content, on a filter, of 33%. Air-drying thus has an impact on triacylglycerol synthesis in C. reinhardtii also, however, the effect is considerably limited, owing probably to instability of the photosynthetic machinery. This air-drying protocol could be useful for the development of a system for industrial production of triacylglycerol with appropriate selection of the algal species.

  14. Analytical solutions for determining extreme water levels in surge tank of hydropower station under combined operating conditions

    Science.gov (United States)

    Wang, Bingbao; Guo, Wencheng; Yang, Jiandong

    2017-06-01

    Combined operating condition usually refers to the control operating condition under which the highest and lowest water levels occur in a surge tank of hydropower station. In this paper, with the basic equations of surge analysis and nonlinear vibrational asymptotic method, analytical expressions of the worst superimposition time of surge waves in an upstream surge tank under four typical combined operating conditions (i.e. load-acceptance-then-rejection, successive load rejection, successive load acceptance and load-rejection-then-acceptance) are derived firstly. Then using these expressions, the analytical extreme water levels are determined. The analytical solutions are verified with numerical simulation results. Finally, the effect of the hydraulic resistance coefficient of surge tank on the control operating condition is investigated. The results indicate that: The analytical solutions for determining extreme water levels in surge tank under various combined operating conditions are accurate due to the good agreements between the analytical results and the numerical results. With the increase of the hydraulic resistance coefficient of surge tank, the control operating condition for the highest water level shifts from load-acceptance-then-rejection condition to successive load rejection condition, and the control operating condition for the lowest water level shifts from load-rejection-then-acceptance condition to successive load acceptance condition.

  15. Reliability of offshore wind power production under extreme wind conditions. Deliverable D 9.5. Work Package 9: Electrical grid

    DEFF Research Database (Denmark)

    Cutululis, Nicolaos Antonio; Zeni, Lorenzo

    Reliability of offshore wind production under extreme wind conditions was investigated in this report. The wind power variability from existing and future large offshore wind farms in Western Denmark were simulated using the Correlated Wind model developed at Risø. The analysis was done for five ...... ramp rates and reserves requirements....

  16. Extreme conditioning programs and injury risk in a US Army Brigade Combat Team.

    Science.gov (United States)

    Grier, Tyson; Canham-Chervak, Michelle; McNulty, Vancil; Jones, Bruce H

    2013-01-01

    Brigades and battalions throughout the US Army are currently implementing a variety of exercise and conditioning programs with greater focus on preparation for mission-specific tasks. An Army physical therapy clinic working with a light infantry brigade developed the Advanced Tactical Athlete Conditioning (ATAC) program. The ATAC program is a unique physical training program consisting of high-intensity aquatic exercises, tactical agility circuits, combat core conditioning, and interval speed training. Along with ATAC, battalions have also incorporated components of fitness programs such as the Ranger Athlete Warrior program and CrossFit (Crossfit, Inc, Santa Monica, CA) an extreme conditioning program (ECP). To determine if these new programs (ATAC, ECP) had an effect on injury rates and physical fitness. Surveys were administered to collect personal characteristics, tobacco use, personal physical fitness training, Army physical fitness test results, and self-reported injuries. Medical record injury data were obtained 6 months before and 6 months after the implementation of the new program. Predictors of injury risk were assessed using multivariate logistic regression. Odds ratios (OR) and 95% confidence intervals (CI) were reported. Injury incidence among Soldiers increased 12% for overall injuries and 16% for overuse injuries after the implementation of the ATAC/ECPs. However, injury incidence among Soldiers not participating in ATAC/ECPs also increased 14% for overall injuries and 10% for overuse injuries. Risk factors associated with higher injury risk for Soldiers participating in ATAC/ECPs included: greater mileage run per week during unit physical training (OR (>16 miles per week÷≤7 miles per week)=2.24, 95% CI, 1.33-3.80); higher body mass index (BMI) (OR (BMI 25-29.9÷BMI<25)=1.77, 95% CI, 1.29-2.44), (OR (BMI =30÷BMI<25)=2.72, 95% CI, 1.67-4.43); cigarette use (OR (smoker÷nonsmoker)=1.80, 95% CI, 1.34-2.42); poor performance on the 2-mile run during

  17. QTL-seq for rapid identification of candidate genes for 100-seed weight and root/total plant dry weight ratio under rainfed conditions in chickpea.

    Science.gov (United States)

    Singh, Vikas K; Khan, Aamir W; Jaganathan, Deepa; Thudi, Mahendar; Roorkiwal, Manish; Takagi, Hiroki; Garg, Vanika; Kumar, Vinay; Chitikineni, Annapurna; Gaur, Pooran M; Sutton, Tim; Terauchi, Ryohei; Varshney, Rajeev K

    2016-11-01

    Terminal drought is a major constraint to chickpea productivity. Two component traits responsible for reduction in yield under drought stress include reduction in seeds size and root length/root density. QTL-seq approach, therefore, was used to identify candidate genomic regions for 100-seed weight (100SDW) and total dry root weight to total plant dry weight ratio (RTR) under rainfed conditions. Genomewide SNP profiling of extreme phenotypic bulks from the ICC 4958 × ICC 1882 population identified two significant genomic regions, one on CaLG01 (1.08 Mb) and another on CaLG04 (2.7 Mb) linkage groups for 100SDW. Similarly, one significant genomic region on CaLG04 (1.10 Mb) was identified for RTR. Comprehensive analysis revealed four and five putative candidate genes associated with 100SDW and RTR, respectively. Subsequently, two genes (Ca_04364 and Ca_04607) for 100SDW and one gene (Ca_04586) for RTR were validated using CAPS/dCAPS markers. Identified candidate genomic regions and genes may be useful for molecular breeding for chickpea improvement. © 2016 The Authors. Plant Biotechnology Journal published by Society for Experimental Biology and The Association of Applied Biologists and John Wiley & Sons Ltd.

  18. High N, dry: Experimental nitrogen deposition exacerbates native shrub loss and nonnative plant invasion during extreme drought.

    Science.gov (United States)

    Valliere, Justin M; Irvine, Irina C; Santiago, Louis; Allen, Edith B

    2017-03-20

    Hotter, longer, and more frequent global change-type drought events may profoundly impact terrestrial ecosystems by triggering widespread vegetation mortality. However, severe drought is only one component of global change, and ecological effects of drought may be compounded by other drivers, such as anthropogenic nitrogen (N) deposition and nonnative plant invasion. Elevated N deposition, for example, may reduce drought tolerance through increased plant productivity, thereby contributing to drought-induced mortality. High N availability also often favors invasive, nonnative plant species, and the loss of woody vegetation due to drought may create a window of opportunity for these invaders. We investigated the effects of multiple levels of simulated N deposition on a Mediterranean-type shrubland plant community in southern California from 2011 to 2016, a period coinciding with an extreme, multi-year drought in the region. We hypothesized that N addition would increase native shrub productivity, but that this would increase susceptibility to drought and result in increased shrub loss over time. We also predicted that N addition would favor nonnatives, especially annual grasses, leading to higher biomass and cover of these species. Consistent with these hypotheses, we found that high N availability increased native shrub canopy loss and mortality, likely due to the higher productivity and leaf area and reduced water-use efficiency we observed in shrubs subject to N addition. As native shrub cover declined, we also observed a concomitant increase in cover and biomass of nonnative annuals, particularly under high levels of experimental N deposition. Together, these results suggest that the impacts of extended drought on shrubland ecosystems may be more severe under elevated N deposition, potentially contributing to the widespread loss of native woody species and vegetation type-conversion. This article is protected by copyright. All rights reserved.

  19. Effects of fibrous fillers on friction and wear properties of polytetrafluoroethylene composites under dry or wet conditions

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    The friction and wear behavior and mechanism as well as the mechanical properties of polytetrafluoroethylene (PTFE) composites filled with potassium titanate whiskers (PTW) and short carbon fibers (CF) under dry, wet and alkaline conditions were investigated. Experiments indicated that owing to appropriate cooling and boundary lubricating effects, the filled PTFE composites showed much lower frictional coefficient and better wear resistance under alkaline than dry and wet sliding conditions. The wear resistance of carbon-fiber-filled PTFE was much better than that of potassium titanate-whisker-filled PTFE composites in water. Results also showed that the transfer film on counterpart rings was significantly hindered by water and alkali. Hydrophilic-filler-reinforced PTFE composites yield higher wear rate when sliding under water.

  20. Spectra and vegetation index variations in moss soil crust in different seasons, and in wet and dry conditions

    Science.gov (United States)

    Fang, Shibo; Yu, Weiguo; Qi, Yue

    2015-06-01

    Similar to vascular plants, non-vascular plant mosses have different periods of seasonal growth. There has been little research on the spectral variations of moss soil crust (MSC) over different growth periods. Few studies have paid attention to the difference in spectral characteristics between wet MSC that is photosynthesizing and dry MSC in suspended metabolism. The dissimilarity of MSC spectra in wet and dry conditions during different seasons needs further investigation. In this study, the spectral reflectance of wet MSC, dry MSC and the dominant vascular plant (Artemisia) were characterized in situ during the summer (July) and autumn (September). The variations in the normalized difference vegetation index (NDVI), biological soil crust index (BSCI) and CI (crust index) in different seasons and under different soil moisture conditions were also analyzed. It was found that (1) the spectral characteristics of both wet and dry MSCs varied seasonally; (2) the spectral features of wet MSC appear similar to those of the vascular plant, Artemisia, whether in summer or autumn; (3) both in summer and in autumn, much higher NDVI values were acquired for wet than for dry MSC (0.6 ∼ 0.7 vs. 0.3 ∼ 0.4 units), which may lead to misinterpretation of vegetation dynamics in the presence of MSC and with the variations in rainfall occurring in arid and semi-arid zones; and (4) the BSCI and CI values of wet MSC were close to that of Artemisia in both summer and autumn, indicating that BSCI and CI could barely differentiate between the wet MSC and Artemisia.

  1. Quantitative Proteomic Analysis of Germination of Nosema bombycis Spores under Extremely Alkaline Conditions

    Science.gov (United States)

    Liu, Han; Chen, Bosheng; Hu, Sirui; Liang, Xili; Lu, Xingmeng; Shao, Yongqi

    2016-01-01

    The microsporidian Nosema bombycis is an obligate intracellular pathogen of the silkworm Bombyx mori, causing the epidemic disease Pebrine and extensive economic losses in sericulture. Although N. bombycis forms spores with rigid spore walls that protect against various environmental pressures, ingested spores germinate immediately under the extremely alkaline host gut condition (Lepidoptera gut pH > 10.5), which is a key developmental turning point from dormant state to infected state. However, to date this process remains poorly understood due to the complexity of the animal digestive tract and the lack of genetic tools for microsporidia. Here we show, using an in vitro spore germination model, how the proteome of N. bombycis changes during germination, analyse specific metabolic pathways employed in detail, and validate key functional proteins in vivo in silkworms. By a label-free quantitative proteomics approach that is directly based on high-resolution mass spectrometry (MS) data, a total of 1136 proteins were identified with high confidence, with 127 proteins being significantly changed in comparison to non-germinated spores. Among them, structural proteins including polar tube protein 1 and 3 and spore wall protein (SWP) 4 and 30 were found to be significantly down-regulated, but SWP9 significantly up-regulated. Some nucleases like polynucleotide kinase/phosphatase and flap endonucleases 1, together with a panel of hydrolases involved in protein degradation and RNA cleavage were overrepresented too upon germination, which implied that they might play important roles during spore germination. The differentially regulated trends of these genes were validated, respectively, by quantitative RT-PCR and 3 proteins of interest were confirmed by Western blotting analyses in vitro and in vivo. Furthermore, the pathway analysis showed that abundant up- and down-regulations appear involved in the glycolysis, pentose phosphate pathway, purine, and pyrimidine metabolism

  2. Quantitative Proteomic Analysis of Germination of Nosema bombycis Spores under Extremely Alkaline Conditions.

    Science.gov (United States)

    Liu, Han; Chen, Bosheng; Hu, Sirui; Liang, Xili; Lu, Xingmeng; Shao, Yongqi

    2016-01-01

    The microsporidian Nosema bombycis is an obligate intracellular pathogen of the silkworm Bombyx mori, causing the epidemic disease Pebrine and extensive economic losses in sericulture. Although N. bombycis forms spores with rigid spore walls that protect against various environmental pressures, ingested spores germinate immediately under the extremely alkaline host gut condition (Lepidoptera gut pH > 10.5), which is a key developmental turning point from dormant state to infected state. However, to date this process remains poorly understood due to the complexity of the animal digestive tract and the lack of genetic tools for microsporidia. Here we show, using an in vitro spore germination model, how the proteome of N. bombycis changes during germination, analyse specific metabolic pathways employed in detail, and validate key functional proteins in vivo in silkworms. By a label-free quantitative proteomics approach that is directly based on high-resolution mass spectrometry (MS) data, a total of 1136 proteins were identified with high confidence, with 127 proteins being significantly changed in comparison to non-germinated spores. Among them, structural proteins including polar tube protein 1 and 3 and spore wall protein (SWP) 4 and 30 were found to be significantly down-regulated, but SWP9 significantly up-regulated. Some nucleases like polynucleotide kinase/phosphatase and flap endonucleases 1, together with a panel of hydrolases involved in protein degradation and RNA cleavage were overrepresented too upon germination, which implied that they might play important roles during spore germination. The differentially regulated trends of these genes were validated, respectively, by quantitative RT-PCR and 3 proteins of interest were confirmed by Western blotting analyses in vitro and in vivo. Furthermore, the pathway analysis showed that abundant up- and down-regulations appear involved in the glycolysis, pentose phosphate pathway, purine, and pyrimidine metabolism

  3. Optimization of wear behavior of electroless Ni-P-W coating under dry and lubricated conditions using genetic algorithm (GA

    Directory of Open Access Journals (Sweden)

    Arkadeb Mukhopadhyay

    2016-12-01

    Full Text Available The present study aims to investigate the tribological behavior of Ni-P-W coating under dry and lubricated condition. The coating is deposited onto mild steel (AISI 1040 specimens by the electroless method using a sodium hypophosphite based alkaline bath. Coating characterization is done to investigate the effect of microstructure on its performance. The change in microhardness is observed to be quite significant after annealing the deposits at 400°C for 1h. A pin–on–disc type tribo-tester is used to investigate the tribological behavior of the coating under dry and lubricated conditions. The experimental design formulation is based on Taguchi’s orthogonal array. The design parameters considered are the applied normal load, sliding speed and sliding duration while the response parameter is wear depth. Multiple regression analysis is employed to obtain a quadratic model of the response variables with the main design parameters under considerations. A high value of coefficient of determination of 95.3% and 87.5% of wear depth is obtained under dry and lubricated conditions, respectively which indicate good correlation between experimental results and the multiple regression models. Analysis of variance at a confidence level of 95% shows that the models are statistically significant. Finally, the quadratic equations are used as objective functions to obtain the optimal combination of tribo testing parameters for minimum wear depth using genetic algorithm (GA.

  4. Damage escape and repair in dried Chroococcidiopsis spp. from hot and cold deserts exposed to simulated space and martian conditions.

    Science.gov (United States)

    Billi, Daniela; Viaggiu, Emanuela; Cockell, Charles S; Rabbow, Elke; Horneck, Gerda; Onofri, Silvano

    2011-01-01

    The cyanobacterium Chroococcidiopsis, overlain by 3 mm of Antarctic sandstone, was exposed as dried multilayers to simulated space and martian conditions. Ground-based experiments were conducted in the context of Lichens and Fungi Experiments (EXPOSE-E mission, European Space Agency), which were performed to evaluate, after 1.5 years on the International Space Station, the survival of cyanobacteria (Chroococcidiopsis), lichens, and fungi colonized on Antarctic rock. The survival potential and the role played by protection and repair mechanisms in the response of dried Chroococcidiopsis cells to ground-based experiments were both investigated. Different methods were employed, including evaluation of the colony-forming ability, single-cell analysis of subcellular integrities based on membrane integrity molecular and redox probes, evaluation of the photosynthetic pigment autofluorescence, and assessment of the genomic DNA integrity with a PCR-based assay. Desiccation survivors of strain CCMEE 123 (coastal desert, Chile) were better suited than CCMEE 134 (Beacon Valley, Antarctica) to withstand cellular damage imposed by simulated space and martian conditions. Exposed dried cells of strain CCMEE 123 formed colonies, maintained subcellular integrities, and, depending on the exposure conditions, also escaped DNA damage or repaired the induced damage upon rewetting.

  5. Estimation of Extreme Values by the Average Conditional Exceedance Rate Method

    Directory of Open Access Journals (Sweden)

    A. Naess

    2013-01-01

    Full Text Available This paper details a method for extreme value prediction on the basis of a sampled time series. The method is specifically designed to account for statistical dependence between the sampled data points in a precise manner. In fact, if properly used, the new method will provide statistical estimates of the exact extreme value distribution provided by the data in most cases of practical interest. It avoids the problem of having to decluster the data to ensure independence, which is a requisite component in the application of, for example, the standard peaks-over-threshold method. The proposed method also targets the use of subasymptotic data to improve prediction accuracy. The method will be demonstrated by application to both synthetic and real data. From a practical point of view, it seems to perform better than the POT and block extremes methods, and, with an appropriate modification, it is directly applicable to nonstationary time series.

  6. Optimization of graphene dry etching conditions via combined microscopic and spectroscopic analysis

    OpenAIRE

    Prado,Mariana C.; Jariwala, Deep; Marks, Tobin J.; Hersam, Mark C.

    2013-01-01

    Single-layer graphene structures and devices are commonly defined using reactive ion etching and plasma etching with O2 or Ar as the gaseous etchants. Although optical microscopy and Raman spectroscopy are widely used to determine the appropriate duration of dry etching, additional characterization with atomic force microscopy (AFM) reveals that residual graphene and/or etching byproducts persist beyond the point where the aforementioned methods suggest complete graphene etching. Recognizing ...

  7. Environmental conditions and biotic interactions influence ecosystem structure and function in a drying stream

    Science.gov (United States)

    Ludlam, J.P.; Magoulick, D.D.

    2010-01-01

    Benthic consumers influence stream ecosystem structure and function, but these interactions depend on environmental context. We experimentally quantified the effects of central stoneroller minnows (Campostoma anomalum (Rafinesque) and Meek's crayfish (Orconectes meeki meeki (Faxon)) on benthic communities using electric exclusion quadrats in Little Mulberry Creek before (June) and during (August) seasonal stream drying. Unglazed ceramic tiles were deployed in June and August to measure periphyton and invertebrate abundance, and leafpack decomposition and primary production were also measured in August. Relationships between stoneroller and crayfish density and the size of consumer effects were evaluated with multiple linear regression models. Average chlorophyll a abundance was greater on exposed than exclusion tiles in August, but not in June. Sediment dry mass, periphyton ash-free dry mass (AFDM), and chironomid densities on tiles did not differ among treatments in either period. Leaf packs decayed faster in exposed than exclusion treatments (kexposed = 0.038 ?? 0.013, kexclusion = 0.007 ?? 0.002), but consumer effects were stronger in some pools than others. Leafpack invertebrate biomass and abundance and tile primary productivity did not differ among treatments. Consumer effects on chlorophyll a were related to crayfish and stoneroller density, and effects on chironomid density were related to stoneroller density. These results contrast with a previous exclusion experiment in Little Mulberry Creek that demonstrated strong consumer effects. The influence of stream drying on consumer effects appears to have been reduced by strong spates, underscoring the importance of conducting multi-year studies to determine the magnitude of variability in ecological interactions. ?? US Government: USGS 2010.

  8. Impact Fretting Wear Behavior of Alloy 690 Tubes in Dry and Deionized Water Conditions

    Science.gov (United States)

    Cai, Zhen-Bing; Peng, Jin-Fang; Qian, Hao; Tang, Li-Chen; Zhu, Min-Hao

    2017-07-01

    The impact fretting wear has largely occurred at nuclear power device induced by the flow-induced vibration, and it will take potential hazards to the service of the equipment. However, the present study focuses on the tangential fretting wear of alloy 690 tubes. Research on impact fretting wear of alloy 690 tubes is limited and the related research is imminent. Therefore, impact fretting wear behavior of alloy 690 tubes against 304 stainless steels is investigated. Deionized water is used to simulate the flow environment of the equipment, and the dry environment is used for comparison. Varied analytical techniques are employed to characterize the wear and tribochemical behavior during impact fretting wear. Characterization results indicate that cracks occur at high impact load in both water and dry equipment; however, the water as a medium can significantly delay the cracking time. The crack propagation behavior shows a jagged shape in the water, but crack extended disorderly in dry equipment because the water changed the stress distribution and retarded the friction heat during the wear process. The SEM and XPS analysis shows that the main failure mechanisms of the tube under impact fretting are fatigue wear and friction oxidation. The effect of medium(water) on fretting wear is revealed, which plays a potential and promising role in the service of nuclear power device and other flow equipments.

  9. Mixed cropping of annual feed legumes with barley improves feed quantity and crude protein content under dry-land conditions

    Directory of Open Access Journals (Sweden)

    Khoshnood Alizadeh

    2013-01-01

    Full Text Available The objective of this research is to determine a suitable mixture of annual feed legumes and barley as a winter crop under dry-land conditions. Seeds of Hungarian vetch (cv. 2670, smooth vetch (cv. Maragheh, and local varieties of grass pea and field pea were mixed with barley (cv. Abidar in a 1:1 ratio and were tested, along with related monoculture. All legumes in the mixture survived winter while legumes alone, except Hungarian vetch, did not survive in the cold areas. The maximum fresh and dry forage yields (56 and 15 ton ha-1 respectively were obtained from a mixture of smooth vetch and barley in provinces with mild winter and more than 400 mm of rainfall. The mixture of barley and smooth vetch resulted in the highest mean crude protein content (17%. Autumn seeding of smooth vetch and barley in a 1:1 ratio produced more than 2 ton ha-1 of dry biomass with good quality in all studied areas and thus could serve as an alternative cropping system after wheat/barley in cold and semi-cold dry land.

  10. Sorption of Cu(II Ions on Chitosan-Zeolite X Composites: Impact of Gelling and Drying Conditions

    Directory of Open Access Journals (Sweden)

    Amal Djelad

    2016-01-01

    Full Text Available Chitosan-zeolite Na-X composite beads with open porosity and different zeolite contents were prepared by an encapsulation method. Preparation conditions had to be optimised in order to stabilize the zeolite network during the polysaccharide gelling process. Composites and pure reference components were characterized using X-ray diffraction (XRD; scanning electron microscopy (SEM; N2 adsorption–desorption; and thermogravimetric analysis (TG. Cu(II sorption was investigated at pH 6. The choice of drying method used for the storage of the adsorbent severely affects the textural properties of the composite and the copper sorption effectiveness. The copper sorption capacity of chitosan hydrogel is about 190 mg·g−1. More than 70% of this capacity is retained when the polysaccharide is stored as an aerogel after supercrititcal CO2 drying, but nearly 90% of the capacity is lost after evaporative drying to a xerogel. Textural data and Cu(II sorption data indicate that the properties of the zeolite-polysaccharide composites are not just the sum of the properties of the individual components. Whereas a chitosan coating impairs the accessibility of the microporosity of the zeolite; the presence of the zeolite improves the stability of the dispersion of chitosan upon supercritical drying and increases the affinity of the composites for Cu(II cations. Chitosan-zeolite aerogels present Cu(II sorption properties.

  11. Crystallization and Thermoelectric Transport in Semiconductor Micro- and Nanostructures Under Extreme Conditions

    Energy Technology Data Exchange (ETDEWEB)

    Gokirmak, Ali [Univ. of Connecticut, Storrs, CT (United States); Silva, Helena [Univ. of Connecticut, Storrs, CT (United States)

    2017-08-30

    This project focused on thermoelectric transport in semiconductor micro and nanostructures where moderate and typical operating voltages and currents lead to extreme thermal gradients and current densities. Models that describe behavior of semiconducting materials typically assume an equilibrium condition or slight deviations from it. In these cases the generation-recombination processes are assumed to have reached a local equilibrium for a given temperature. Hence, free carrier concentrations and their mobilities, band-gap, thermal conductivity, thermoelectric properties, mobility of atoms and mechanical properties of the material, can be described as a function of temperature. In the case of PN junctions under electrical bias, carrier concentrations can change up to ~ 1020 cm-3 and a drift-diffusion approximation is typically used to obtain the carrier concentrations while assuming that the material properties do not change. In non-equilibrium conditions, the assumption that the material properties remain the same may not be valid. While the increased conduction-band electron concentration may not have a drastic effect on the material, large hole concentration is expected to soften the material as ‘a hole’ comes into existence as a broken bond in the lattice. As the hole density approaches 1022 cm-3, the number of bonds holding the lattice together is significantly reduced, making it easier to break additional bonds, reduce band-gap and inhibit phonon transport. As these holes move away from where they were generated, local properties are expected to deviate significantly from the equilibrium case. Hence, temperature alone is not sufficient to describe the behavior of the material. The behavior of the solid material close to a molten region (liquid-solid interfaces) is also expected to deviate from the equilibrium case as a function of hole injection rate, which can be drastically increased or decreased in the presence of an electric field. In the past years

  12. The effect of visual field condition on kinetic in upper extremities and e.m.g in lower extremities while performing reaching in normal adults

    Science.gov (United States)

    Park, Hyekang; Kang, Youngeun; Yoo, Minah; Lee, Bomjin; Yang, Jeongok; Lee, Joongsook; Han, Dongwook; Oh, Taeyoung

    2017-01-01

    [Purpose] The aims of this study was to investigate mean velocity and angle of shoulder joint, activation of tibialis anterior and gastrocnemius according to both eyes, dominant eye and non-dominant eye condition during reaching task in normal adults. [Subjects and Methods] Our research recruited 24 participants (male 11, female 13) in Silla University. Participants were performed reaching out movement by conditions of both eye, dominants eye, non-dominants eye. The target was placed at 45 degree diagonal direction and distance far away 130% of their arm length. Kinetic analysis of the upper extremities was investigated by QUALISYS 3-dimensional motion analysis system. Muscle activation were measured by EMG during reaching tasks. The collected data were statistically processed using the SPSS for win version 20.0. [Results] There was a significant difference of shoulder joint velocity of flexion, abduction and internal rotation according to visual field condition during reaching tasks. There was no significant difference of shoulder joint angle and muscle activation according to visual field conditions during reaching tasks. [Conclusion] In conclusion, visual field has an influence on shoulder joint velocity. Therefore, the visual field may be to play an important role in reach performance. PMID:28210047

  13. Net joint kinetics in the limbs of pigs walking on concrete floor in dry and contaminated conditions.

    Science.gov (United States)

    Thorup, V M; Laursen, B; Jensen, B R

    2008-04-01

    In pigs (Sus scrofa), joint disorders are frequent leg problems, and inappropriate pigpen floors and slippery floor conditions may contribute to these problems. Therefore, this study first aimed to quantify the net joint kinetics (net joint moments and net joint reaction forces) in the forelimbs and hindlimbs of healthy pigs walking on solid concrete floors. Second, this study aimed to examine the effect of floor condition on the net joint kinetics. Kinematic (50-Hz video recordings) and kinetic (1-kHz force plate measurements) data were collected from 30 pigs and combined with body segment parameters from a cadaver study. Net joint kinetics was calculated by using a 2-dimensional inverse dynamic solution. Inverse dynamics have, to our knowledge, not been applied in pigs before. Dry, greasy, and wet floor conditions were tested with 10 pigs each. In the forelimbs, peak joint moment was less (P < 0.01) on greasy (0.184 +/- 0.012 Nm/kg, moment of force per kg of BW) than on dry (0.232 +/- 0.012 Nm/kg) or wet (0.230 +/- 0.012 Nm/kg) conditions. Additionally, the minimum forelimb joint moment was more negative (P < 0.05) on greasy (-0.119 +/- 0.009 Nm/kg) than on dry or wet (both -0.091 +/- 0.009 Nm/kg) conditions. The forelimb joint reaction forces and the hindlimb joint kinetics were unaffected by floor condition. The greatest (P < 0.001) joint moments occurred in the shoulder (-0.376 +/- 0.007 Nm/kg), elbow (0.345 +/- 0.009 Nm/kg), hip (0.252 +/- 0.009 Nm/kg), and tarsal (0.329 +/- 0.009 Nm/kg) joints, which may be related to the greater incidence of joint diseases in some of these joints. In conclusion, the forelimb joints of the pigs responded more markedly to floor condition than did their hindlimb joints, probably because the forelimbs carry more weight. In particular, between the dry and greasy floor conditions, the joint loading differed, most likely because the pigs adapted to a potentially slippery surface.

  14. Effect of conditioning methods on the microtensile bond strength of phosphate monomer-based cement on zirconia ceramic in dry and aged conditions.

    Science.gov (United States)

    Amaral, Regina; Ozcan, Mutlu; Valandro, Luiz Felipe; Balducci, Ivan; Bottino, Marco Antonio

    2008-04-01

    The objective of this study was to evaluate the durability of bond strength between a resin cement and aluminous ceramic submitted to various surface conditioning methods. Twenty-four blocks (5 x 5 x 4 mm(3)) of a glass-infiltrated zirconia-alumina ceramic (In-Ceram Zirconia Classic) were randomly divided into three surface treatment groups: ST1-Air-abrasion with 110-mum Al2O3 particles + silanization; ST2-Laboratory tribochemical silica coating method (110-microm Al2O3, 110-microm silica) (Rocatec) + silanization; ST3-Chairside tribochemical silica coating method (30-microm SiO(x)) (CoJet) + silanization. Each treated ceramic block was placed in its silicone mold with the treated surface exposed. The resin cement (Panavia F) was prepared and injected into the mold over the treated surface. Specimens were sectioned to achieve nontrimmed bar specimens (14 sp/block) that were randomly divided into two conditions: (a) Dry-microtensile test after sectioning; (b) Thermocycling (TC)-(6,000x, 5-55 degrees C) and water storage (150 days). Thus, six experimental groups were obtained (n = 50): Gr1-ST1 + dry; Gr2-ST1 + TC(;) Gr3-ST2 + dry; Gr4-ST2 + TC; Gr5-ST3 + dry; Gr6-ST3 + TC. After microtensile testing, the failure types were noted. ST2 (25.1 +/- 11) and ST3 (24.1 +/- 7.4) presented statistically higher bond strength (MPa) than that of ST1 (17.5 +/- 8) regardless of aging conditions (p silanization showed durable bond strength. After aging, air-abrasion with 110-microm Al(2)O(3) + silanization showed the largest decrease indicating that aging is fundamental for bond strength testing for acid-resistant zirconia ceramics in order to estimate their long-term performance in the mouth.

  15. Mercury critical concentrations to Enchytraeus crypticus (Annelida: Oligochaeta) under normal and extreme conditions of moisture in tropical soils - Reproduction and survival.

    Science.gov (United States)

    Buch, Andressa Cristhy; Schmelz, Rüdiger M; Niva, Cintia Carla; Correia, Maria Elizabeth Fernandes; Silva-Filho, Emmanoel Vieira

    2017-05-01

    Soil provides many ecosystem services that are essential to maintain its quality and healthy development of the flora, fauna and human well-being. Environmental mercury levels may harm the survival and diversity of the soil fauna. In this respect, efforts have been made to establish limit values of mercury (Hg) in soils to terrestrial fauna. Soil organisms such as earthworms and enchytraeids have intimate contact with trace metals in soil by their oral and dermal routes, reflecting the potentially adverse effects of this contaminant. The main goal of this study was to obtain Hg critical concentrations under normal and extreme conditions of moisture in tropical soils to Enchytraeus crypticus to order to assess if climate change may potentiate their acute and chronic toxicity effects. Tropical soils were sampled from of two Forest Conservation Units of the Rio de Janeiro State - Brazil, which has been contaminated by Hg atmospheric depositions. Worms were exposed to three moisture conditions, at 20%, 50% and 80% of water holding capacity, respectively, and in combination with different Hg (HgCl2) concentrations spiked in three types of tropical soil (two natural soils and one artificial soil). The tested concentrations ranged from 0 to 512mg Hg kg(-1) dry weight. Results indicate that the Hg toxicity is higher under increased conditions of moisture, significantly affecting survival and reproduction rate. Copyright © 2017 Elsevier Inc. All rights reserved.

  16. Initial corrosion behavior of AZ91 magnesium alloy in simulating acid rain under wet-dry cyclic condition

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    Corrosion behavior of AZ91 magnesium alloy in simulating acid rain under wet-dry cyclic condition was investigated.The results show that corrosion potential shifts positively and the corrosion current density decreases at low wet-dry cyclic time.Further increase of the cyclic time results in the negative movement of corrosion potential and the increase of current density.SEM observation indicates that corrosion Occurs only in αphase,βphase is inert in corrosive medium,and the corrosion of AZ91 magnesium appears in uniform characteristic.XPS analysis suggests that the corrosion product is mainly composed of oxide and hydroxide of magnesium and aluminum,and a small amount of sulfate is also contained in the film.

  17. Modulating Role of Vitamins C and E against Transport-Induced Stress in Pullets during the Hot-Dry Conditions.

    Science.gov (United States)

    Minka, N S; Ayo, J O

    2011-01-01

    The modulating effects of ascorbic acid (AA), vitamin E (E), and a combination of AA and E (AA + E) against eight-hour road transportation stress were investigated in 120 pullets during the hot-dry season. The result obtained showed that handling, loading and transportation induced lymphopenia, neutrophilia, liveweight loss, and mortality, which was alleviated by oral administration of AA, E, and AA + E at doses of 60 mg, 30 mg, and 60 + 30 mg per kg bodyweight, respectively, 30 minutes before being loaded and transported. The meteorological conditions recorded during the study period were higher (P < .05) than the thermoneutral values established for chickens in the zone. In conclusion, the administration of vitamins AA, E, and AA + E, especially AA, ameliorated the risk of adverse effects of handling, loading, transportation, and thermal stress in pullets during the hot-dry season.

  18. Exceedance Frequency Analysis of Contaminants in Streams Under Dry-Weather Conditions in Denton, Texas.

    Science.gov (United States)

    Shrestha, Manjul; Hudak, Paul F

    2016-02-01

    Percentages of dry-weather stream samples exceeding water quality criteria for ten parameters were compiled for mixed land use watersheds in north-central Texas. Most problematic were total suspended solids (TSS), total dissolved solids (TDS), ammonia, nitrate, phosphorus and copper. Nutrients had much higher exceedance frequency at a sampling station impacted by wastewater discharge. Whereas, TSS and TDS exceedance frequency was highest in predominantly agricultural and rangeland watersheds, and urbanized watersheds respectively. Total dissolved solids was most often exceeded in urbanized watersheds. For several parameters, especially TDS, TSS, ammonia and copper, median concentrations were below water quality thresholds in most watersheds, but exceedance frequency was high. For example, median TSS was less than its threshold in every watershed, but exceedance frequency was higher than 10 % in four of five watersheds - and nearly 43 % in one watershed. This pattern reflects the skewed nature of water quality data; often times, many observations cluster around the lowest values, causing the median to be relatively low, but several (high) outliers form the right-hand tail of the distribution. Results of this study indicate a need to examine exceedance frequency in addition to traditional descriptive measures to better understand dry-weather stream quality in watersheds.

  19. Temperature and moisture conditions for life in the extreme arid region of the Atacama desert: four years of observations including the El Nino of 1997-1998

    Science.gov (United States)

    McKay, Christopher P.; Friedmann, E. Imre; Gomez-Silva, Benito; Caceres-Villanueva, Luis; Andersen, Dale T.; Landheim, Ragnhild

    2003-01-01

    The Atacama along the Pacific Coast of Chile and Peru is one of the driest and possibly oldest deserts in the world. It represents an extreme habitat for life on Earth and is an analog for life in dry conditions on Mars. We report on four years (September 1994-October 1998) of climate and moisture data from the extreme arid region of the Atacama. Our data are focused on understanding moisture sources and their role in creating suitable environments for photosynthetic microorganisms in the desert surface. The average air temperature was 16.5 degrees C and 16.6 degrees C in 1995 and 1996, respectively. The maximum air temperature recorded was 37.9 degrees C, and the minimum was -5.7 degrees C. Annual average sunlight was 336 and 335 W m(-2) in 1995 and 1996, respectively. Winds averaged a few meters per second, with strong fohn winds coming from the west exceeding 12 m s(-1). During our 4 years of observation there was only one significant rain event of 2.3 mm, which occurred near midnight local time. We suggest that this event was a rainout of a heavy fog. It is of interest that the strong El Nino of 1997-1998 brought heavy rainfall to the deserts of Peru, but did not bring significant rain to the central Atacama in Chile. Dew occurred at our station frequently following high nighttime relative humidity, but is not a significant source of moisture in the soil or under stones. Groundwater also does not contribute to surface moisture. Only the one rain event of 2.3 mm resulted in liquid water in the soil and beneath stones for a total of only 65-85 h over 4 years. The paucity of liquid water under stones is consistent with the apparent absence of hypolithic (under-stone) cyanobacteria, the only known primary producers in such extreme deserts.

  20. A First-Principles Multi-phase Equation of State of Carbon under Extreme Conditions

    Energy Technology Data Exchange (ETDEWEB)

    Correa, A A; Benedict, X L; Young, D A; Schwegler, E; Bonev, S A

    2008-02-01

    We describe the construction of a multi-phase equation of state for carbon at extreme pressures based on ab initio electronic structure calculations of two solid phases (diamond and BC8) and the liquid. Solid-phase free energies are built from knowledge of the cold curves and phonon calculations, together with direct ab initio molecular dynamics calculations of the equation of state, which are used to extract anharmonic corrections to the phonon free energy. The liquid free energy is constructed based on results from molecular dynamics calculations and constraints determined from previously calculated melting curves, assuming a simple solid-like free energy model. The resulting equation of state is extended to extreme densities and temperatures with a Thomas Fermi-based free energy model. Comparisons to available experimental results are discussed.

  1. Response of shoal grass, Halodule wrightii, to extreme winter conditions in the Lower Laguna Madre, Texas

    Science.gov (United States)

    Hicks, D.W.; Onuf, C.P.; Tunnell, J.W.

    1998-01-01

    Effects of a severe freeze on the shoal grass, Halodule wrightii, were documented through analysis of temporal and spatial trends in below-ground biomass. The coincidence of the second lowest temperature (-10.6??C) in 107 years of record, 56 consecutive hours below freezing, high winds and extremely low water levels exposed the Laguna Madre, TX, to the most severe cold stress in over a century. H. wrightii tolerated this extreme freeze event. Annual pre- and post-freeze surveys indicated that below-ground biomass estimated from volume was Unaffected by the freeze event. Nor was there any post-freeze change in biomass among intertidal sites directly exposed to freezing air temperatures relative to subtidal sites which remained submerged during the freezing period.

  2. Kelp and seaweed feeding by High-Arctic wild reindeer under extreme winter conditions

    OpenAIRE

    2012-01-01

    One challenge in current Arctic ecological research is to understand and predict how wildlife may respond to increased frequencies of ‘‘extreme’’ weather events. Heavy rain-on-snow (ROS) is one such extreme phenomenon associated with winter warming that is not well studied but has potentially profound ecosystem effects through changes in snow-pack properties and ice formation. Here, we document how ice-locked pastures following substantial amounts of ROS forced coastal Svalbard reindeer (Rang...

  3. Investigation of carbon dioxide phase shift possibility under extreme Antarctic winter conditions

    CERN Document Server

    Vashchenko, V M

    2014-01-01

    The Antarctic winter atmosphere minimal temperature and pressure series reveal that $CO_2$ phase shift (deposition) is possible in some extreme cases, even leading to possible $CO_2$ snow phenomenon at Vostok Antarctic station and in other near South Pole regions. A hypothesis has been formulated that stable $CO_2$ snow cover might have formed in Earth past which may influence interpretation of glacial chronology records. This effect may also manifest in other minor gases. Its global climate role is discussed.

  4. Intestinal anisakiasis can cause intussusception in adults:An extremely rare condition

    Institute of Scientific and Technical Information of China (English)

    Tomofumi; Miura; Akira; Iwaya; Takao; Shimizu; Junpei; Tsuchiya; Junichiro; Nakamura; Satoshi; Yamada; Tsutomu; Miura; Masahiko; Yanagi; Hiroyuki; Usuda; Iwao; Emura; Toru; Takahashi

    2010-01-01

    We report an extremely rare case of adult intussusception caused by anisakiasis. A 41-year-old man was admitted into our hospital for right lower abdominal colicky pain. Ultrasonography and computed tomography revealed the presence of intussusception. As pneumodynamic resolution by colonoscopy failed, surgery was performed. The anisakis body was found in the submucosal layer of the resection specimen. The patient was discharged 9 d after the operation. Anisakiasis may cause intussusception in any country wh...

  5. Sediment Dynamics Within Buffer Zone and Sinkhole Splay Areas Under Extreme Soil Disturbance Conditions.

    Science.gov (United States)

    Schoonover, Jon E; Crim, Jackie F; Williard, Karl W J; Groninger, John W; Zaczek, James J; Pattumma, Klairoong

    2015-09-01

    Sedimentation dynamics were assessed in sinkholes within training areas at Ft. Knox Military Installation, a karst landscape subjected to decades of tracked vehicle use and extreme soil disturbance. Sinkholes sampled were sediment-laden and behaved as intermittent ponds. Dendrogeomorphic analyses were conducted using willow trees (Salix spp.) located around the edge of 18 sinkholes to estimate historical sedimentation rates, and buried bottles were installed in 20 sinkholes at the center, outer edge, and at the midpoint between the center and edge to estimate annual sedimentation rates. Sedimentation data were coupled with vegetation characteristics of sinkhole buffers to determine relationships among these variables. The dendrogeomorphic method estimated an average accumulation rate of 1.27 cm year(-1) translating to a sediment loss rate of 46.1 metric ton year(-1) from the training areas. However, sediment export to sinkholes was estimated to be much greater (118.6 metric ton year(-1)) via the bottle method. These data suggest that the latter method provided a more accurate estimate since accumulation was greater in the center of sinkholes compared to the periphery where dendrogeomorphic data were collected. Vegetation data were not tightly correlated with sedimentation rates, suggesting that further research is needed to identify a viable proxy for direct measures of sediment accumulation in this extreme deposition environment. Mitigation activities for the sinkholes at Ft. Knox's tank training area, and other heavily disturbed karst environments where extreme sedimentation exists, should consider focusing on flow path and splay area management.

  6. Core safety of Indian nuclear power plants (NPPs) under extreme conditions

    Indian Academy of Sciences (India)

    J B Joshi; A K Nayak; M Singhal; D Mukhopadhaya

    2013-10-01

    Nuclear power is currently the fourth largest source of electricity production in India after thermal, hydro and renewable sources of electricity. Currently, India has 20 nuclear reactors in operation and seven other reactors are under construction. Most of these reactors are indigenously designed and built Heavy Water Reactors. In addition, a 300 MWe Advanced Heavy Water Reactor has already been designed and in the process of deployment in near future for demonstration of power production from Thorium apart from enhanced safety features by passive means. India has ambitious plans to enhance the share of electricity production from nuclear. The recent Fukushima accident has raised concerns of safety of Nuclear Power Plants worldwide. The Fukushima accident was caused by extreme events, i.e., large earthquake followed by gigantic Tsunami which are not expected to hit India’s coast considering the geography of India and historical records. Nevertheless, systematic investigations have been conducted by nuclear scientists in India to evaluate the safety of the current Nuclear Power Plants in case of occurrence of such extreme events in any nuclear site. This paper gives a brief outline of the safety features of Indian Heavy Water Reactors for prevention and mitigation of such extreme events. The probabilistic safety analysis revealed that the risk from Indian Heavy Water Reactors are negligibly small.

  7. Operational flood management under large-scale extreme conditions, using the example of the Middle Elbe

    Directory of Open Access Journals (Sweden)

    A. Kron

    2010-06-01

    Full Text Available In addition to precautionary or technical flood protection measures, short-term strategies of the operational management, i.e. the initiation and co-ordination of preventive measures during and/or before a flood event are crucially for the reduction of the flood damages. This applies especially for extreme flood events. These events are rare, but may cause a protection measure to be overtopped or even to fail and be destroyed. In such extreme cases, reliable decisions must be made and emergency measures need to be carried out to prevent even larger damages from occurring.

    Based on improved methods for meteorological and hydrological modelling a range of (physically based extreme flood scenarios can be derived from historical events by modification of air temperature and humidity, shifting of weather fields and recombination of flood relevant event characteristics. By coupling the large scale models with hydraulic and geotechnical models, the whole flood-process-chain can be analysed right down to the local scale. With the developed GIS-based tools for hydraulic modelling FlowGIS and the Dike-Information-System, (IS-dikes it is possible to quantify the endangering shortly before or even during a flood event, so the decision makers can evaluate possible options for action in operational mode.

  8. Correlations in condensed matter under extreme conditions a tribute to Renato Pucci on the occasion of his 70th birthday

    CERN Document Server

    2017-01-01

    This book addresses a wide range of topics relating to the properties and behavior of condensed matter under extreme conditions such as intense magnetic and electric fields, high pressures, heat and cold, and mechanical stresses. It is divided into four sections devoted to condensed matter theory, molecular chemistry, theoretical physics, and the philosophy and history of science. The main themes include electronic correlations in material systems under extreme pressure and temperature conditions, surface physics, the transport properties of low-dimensional electronic systems, applications of the density functional theory in molecular systems, and graphene. The book is the outcome of a workshop held at the University of Catania, Italy, in honor of Professor Renato Pucci on the occasion of his 70th birthday. It includes selected invited contributions from collaborators and co-authors of Professor Pucci during his long and successful career, as well as from other distinguished guest authors.

  9. Study on Strength of Hybrid Mortar Synthesis with Epoxy Resin, Fly Ash and Quarry Dust Under Extreme Conditions

    Science.gov (United States)

    Sudheer, P.; Muni Reddy, M. G., Dr.; Adiseshu, S., Dr.

    2017-08-01

    Blend and characterization of Bisphenol-A diglycidyl ether based thermosetting polymer mortar comprising an epoxy resin, Fly ash and Quarry dust are presented here for the strength study. The specimens have been prepared by means of an innovative process in Extreme conditions of commercial epoxy resin, Fly ash and Quarry dust based paste. In this way, thermosetting based hybrid mortars characterized by a different contents of normalized Fly ash and Quarry dust by a homogeneous distribution of the resin have been attained. Once hardened, these new composite materials show improved compressive strength and toughness in respect to both the Fly ash and Rock sand pastes since the Resin provides a more cohesive microstructure, with a reduced number of micro cracks. The micro structural characterization allows pointing out the presence of an Interfacial Transition Zone similar to that observed in cement based mortars. A correlation between micro-structural features and mechanical properties of the mortar has also been studied in Extreme conditions.

  10. Corrosion Evolution of Reinforcing Steel in Concrete under Dry/Wet Cyclic Conditions Contaminated with Chloride

    Institute of Scientific and Technical Information of China (English)

    J. Wei; X.X. Fu; J.H. Dong; W. Ke

    2012-01-01

    The corrosion evolution of rebar in concrete was monitored by electrochemical impedance spectroscopy (EIS) under dry/wet alternated accelerated corrosion test. Four stages with different dynamic characteristics were observed during the corrosion evolution. They were passive stage, local corrosion controlled by the charge transfer step, accelerated corrosion controlled by the mass transfer step, and constant rate corrosion controlled by the mass transfer step through a barrier layer. X-ray diffraction (XRD) analysis showed that the corrosion product of rebar in mortar was composed of α-FeOOH, γ-FeOOH and Fe304. The corrosion mechanisms of all four stages were discussed and the corrosion reactions were proposed according to the corrosion product and corrosion evolution characteristics.

  11. Plastic Growth response of European beech provenances to dry site conditions

    NARCIS (Netherlands)

    Stojnic, S.; Sass, U.G.W.; Orlovic, S.; Matovic, B.; Eilmann, B.

    2013-01-01

    Due to projected global warming, there is a great concern about the ability of European beech to adapt to future climate conditions. Provenance trials provide an excellent basis to assess the potential of various provenances to adjust to given climate conditions. In this study we compared the perfor

  12. Optimisation of freeze drying conditions for purified serine protease from mango (Mangifera indicaCv. Chokanan) peel.

    Science.gov (United States)

    Mehrnoush, Amid; Tan, Chin Ping; Hamed, Mirhosseini; Aziz, Norashikin Ab; Ling, Tau Chuan

    2011-09-01

    This study investigated the possible relationship between the encapsulation variables, namely serine protease content (9-50mg/ml, X1), Arabic gum (0.2-10%(w/w), X2), maltodextrin (2-5%(w/w), X3) and calcium chloride (1.3-5.5%(w/w), X4) on the enzymatic properties of encapsulated serine protease. The study demonstrated that Arabic gum, maltodextrin and calcium chloride, as coating agents, protected serine protease from activity loss during freeze-drying. The overall optimum region resulted in a suitable freeze drying condition with a yield of 92% for the encapsulated serine protease, were obtained using 29.5mg/ml serine protease content, 5.1%(w/w) Arabic gum, 3.5%(w/w) maltodextrin and 3.4%(w/w) calcium chloride. It was found that the interaction effect of Arabic gum and calcium chloride improved the serine protease activity, and Arabic gum was the most effective amongst the examined coating agents. Thus, Arabic gum should be considered as potential protection in freeze drying of serine protease.

  13. Dry Matter Accumulation and Remobilization in Grain Sorghum Genotypes (Sorghum bicolor L. Moench (underNormal and Water Stress Conditions

    Directory of Open Access Journals (Sweden)

    A Beheshti

    2011-02-01

    Full Text Available Abstract Production, remobilization and accumulation of assimilates in crops especially under water stress are essential factors for determination and studying the yield differences of species and cultivars. Field experiment was conducted using a split plot design based on a randomized complete block design with 3 replication s during 2007 growing season in agricultural research station (Khorasan Agricultural and Natural Resource Research Center, Mashhad-Iran. Main plots were consisted of 2 levels of water, water deficit after anthesis and normal condition (with out water stress and factorial arrangement of photosynthesis status (non desiccation and chemical desiccation with potassium iodide and 3 grain sorghum genotypes (Sepide, M5 and M2 promising lines were assigned to sub plots. Results of variance analysis showed, that the effects of water stress on dry matter accumulation, efficiency of remobilization (REE, percent of remobilization (REP, biologic yield were significant in (p≤0.01 (and grain yield (economic yield was significant in p≤0.05, respectively. Water deficit caused an increase of 10.08%, 24.45 % and 12.43% in dry matter accumulation, percent of remobilization and efficiency of remobilization, respectively as compared to normal conditions. This in turn was led to decrease in seed yield, biological yield and harvest index by 36.38%, 5.43% and 31.60%, respectively. The effect of disturbance in current photosynthesis was significant in all of traits and caused the increase of 15.58%, 17.5% and 36.62% in dry matter accumulation, efficiency of remobilization and percent of remobilization, respectively. The role of remobilization was crucial in sorghum genotypes. Interaction between factors showed that highest dry matter accumulation, percentage of remobilization and efficiency of remobilization was in drought stress and disturbance in current photosynthesis and was 16.62%, 62.54 and 24.60%, respectively and was significantly

  14. Extremely low prevalence of Batrachochytrium dendrobatidis in frog populations from neotropical dry forest of Costa Rica supports the existence of a climatic refuge from disease.

    Science.gov (United States)

    Zumbado-Ulate, Héctor; Bolaños, Federico; Gutiérrez-Espeleta, Gustavo; Puschendorf, Robert

    2014-12-01

    Population declines and extinctions of numerous species of amphibians, especially stream-breeding frogs, have been linked to the emerging infectious disease chytridiomycosis, caused by the chytrid fungus, Batrachochytrium dendrobatidis. In Central America, most of the 34 species of the Craugastor punctariolus species group have disappeared in recent years in high- and low-elevation rainforests. Distribution models for B. dendrobatidis and the continuous presence of the extirpated stream-dwelling species, Craugastor ranoides, in the driest site of Costa Rica (Santa Elena Peninsula), suggest that environmental conditions might restrict the growth and development of B. dendrobatidis, existing as a refuge from chytridiomycosis-driven extinction. We conducted field surveys to detect and quantify the pathogen using Real-time PCR in samples from 15 species of frogs in two locations of tropical dry forest. In Santa Elena Peninsula, we swabbed 310 frogs, and only one sample of the species, C. ranoides, tested positive for B. dendrobatidis (prevalence refuges from chytridiomycosis and highlights the importance of tropical dry forest conservation for amphibians in the face of epidemic disease.

  15. Vadose-zone moisture dynamics under radiation boundary conditions during a drying process

    Institute of Scientific and Technical Information of China (English)

    韩江波; 周志芳; 傅志敏; 王锦国

    2014-01-01

    In order to better understand the soil moisture dynamics during a drying process, a soil column experiment is conducted in the laboratory, followed by the numerical modeling with consideration of the coupled liquid water, water vapor and heat transport in the vadose zone. Results show that there are three distinct subzones above the water table according to the temporally dynamic variation of the water content profiles. Zone 1 sees a decrease in the water contents in the upper profiles (0 m-0.05 m) due to a negative net water flux in this zone where the upward isothermal water vapor flux becomes the main flow mechanism in the soils. In contrast, the water content within Zone 2 in the depth ranging from 0.05 m to 0.37 m sees an apparent increase over time, resulting from the positive net thermal water-vapor and isothermal liquid-water fluxes into this layer. Zone 3 (0.37 m-0.65 m) also sees an apparent decrease in the water content since the isothermal liquid water flux carries the liquid water either upward out of this region for vaporization or downward to the water table as a recharge to the groundwater.

  16. Wear mechanism for spray deposited Al-Si/SiCp composites under dry sliding condition

    Institute of Scientific and Technical Information of China (English)

    滕杰; 李华培; 陈刚

    2015-01-01

    Al-Si/15%SiCp (volume fraction) composites with different silicon contents were fabricated by spray deposition technique, and typical microstructures of these composites were studied by optical microscopy (OM). Dry sliding wear tests were carried out using a block-on-ring wear machine to investigate the effect of applied load range of 10−220 N on the wear and friction behavior of these composites sliding against SAE 52100 grade bearing steel. Scanning electron microscopy (SEM) and energy-dispersive X-ray microanalysis (EDAX) were utilized to examine the morphologies of the worn surfaces in order to observe the wear characteristics and investigate the wear mechanism. The results show that the wear behavior of these composites is dependent on the silicon content in the matrix alloy and the applied load. Al-Si/15%SiCp composites with higher silicon content exhibit better wear resistance in the applied load range. Under lower loads, the major wear mechanisms are oxidation wear and abrasive wear for all tested composites. Under higher loads, severe adhesive wear becomes the main wear mechanisms for Al-7Si/15%SiCp and Al-13Si/15%SiCp composites, while Al-20Si/15%SiCp presents a compound wear mechanism, consisting of oxidation, abrasive wear and adhesion wear.

  17. Impact of urban WWTP and CSO fluxes on river peak flow extremes under current and future climate conditions.

    Science.gov (United States)

    Keupers, Ingrid; Willems, Patrick

    2013-01-01

    The impact of urban water fluxes on the river system outflow of the Grote Nete catchment (Belgium) was studied. First the impact of the Waste Water Treatment Plant (WWTP) and the Combined Sewer Overflow (CSO) outflows on the river system for the current climatic conditions was determined by simulating the urban fluxes as point sources in a detailed, hydrodynamic river model. Comparison was made of the simulation results on peak flow extremes with and without the urban point sources. In a second step, the impact of climate change scenarios on the urban fluxes and the consequent impacts on the river flow extremes were studied. It is shown that the change in the 10-year return period hourly peak flow discharge due to climate change (-14% to +45%) was in the same order of magnitude as the change due to the urban fluxes (+5%) in current climate conditions. Different climate change scenarios do not change the impact of the urban fluxes much except for the climate scenario that involves a strong increase in rainfall extremes in summer. This scenario leads to a strong increase of the impact of the urban fluxes on the river system.

  18. Equation of state density models for hydrocarbons in ultradeep reservoirs at extreme temperature and pressure conditions

    Science.gov (United States)

    Wu, Yue; Bamgbade, Babatunde A.; Burgess, Ward A.; Tapriyal, Deepak; Baled, Hseen O.; Enick, Robert M.; McHugh, Mark A.

    2013-10-01

    The necessity of exploring ultradeep reservoirs requires the accurate prediction of hydrocarbon density data at extreme temperatures and pressures. In this study, three equations of state (EoS) models, Peng-Robinson (PR), high-temperature high-pressure volume-translated PR (HTHP VT-PR), and perturbed-chain statistical associating fluid theory (PC-SAFT) EoS are used to predict the density data for hydrocarbons in ultradeep reservoirs at temperatures to 523 K and pressures to 275 MPa. The calculated values are compared with experimental data. The results show that the HTHP VT-PR EoS and PC-SAFT EoS always perform better than the regular PR EoS for all the investigated hydrocarbons.

  19. How light modifies the electron–electron interaction under extreme conditions

    Energy Technology Data Exchange (ETDEWEB)

    Hinschberger, Y. [Instituto de Física dos Materiais da Universidade do Porto, Departamento de Física e Astronomia, Rua do campo Alegre, 687, 4169-007 Porto (Portugal); Hervieux, P.-A., E-mail: hervieux@ipcms.u-strasbg.fr [Institut de Physique et Chimie des Matériaux de Strasbourg, CNRS and Université de Strasbourg, 23 rue du Loess, BP 43, 67034 Strasbourg Cedex 2 (France)

    2015-10-02

    In the domain of extreme light–matter interactions, we show that the electron–electron interaction can be modified coherently by the electric field of the light. The latter play the role of a third partner not only acting on the electrons individually but also on their mutual interaction. By using an original formalism based on the Foldy–Wouthuysen transformation and applied to the Dirac–Breit Hamiltonian in the presence of a time-dependent electromagnetic field, we obtain analytical expressions of new three-body light–matter interactions. - Highlights: • A time-dependent electromagnetic field can modify the electronic interaction. • Analytical expressions of this three-body light matter interactions are presented. • Effects can be evaluated with the amplitude of the laser and electronic distance.

  20. Parameterization of gaseous dry deposition in atmospheric chemistry models: Sensitivity to aerodynamic resistance formulations under statically stable conditions

    Science.gov (United States)

    Toyota, Kenjiro; Dastoor, Ashu P.; Ryzhkov, Andrei

    2016-12-01

    Turbulence controls the vertical transfer of momentum, heat and trace constituents in the atmospheric boundary layer. In the lowest 10% of this layer lies the surface boundary layer (SBL) where the vertical fluxes of transferred quantities have been successfully parameterized using the Monin-Obukhov similarity theory in weather forecast, climate and atmospheric chemistry models. However, there is a large degree of empiricism in the stability-correction parameterizations used to formulate eddy diffusivity and aerodynamic resistance particularly under strongly stable ambient conditions. Although the influence of uncertainties in stability-correction parameterizations on eddy diffusivity is actively studied in boundary-layer meteorological modeling, its impact on dry deposition in atmospheric chemistry modeling is not well characterized. In this study, we address this gap by providing the mathematical basis for the relationship between the formulations of vertical surface flux used in meteorological and atmospheric chemistry modeling communities, and by examining the sensitivity of the modeled dry deposition velocities in statically stable SBL to the choice of stability-correction parameterizations used in three operational and/or research environmental models (GEM/GEM-MACH, ECMWF IFS and CMAQ-MM5). Aerodynamic resistances (ra) calculated by the three sets of parameterizations are notably different from each other and are also different from those calculated by a "z-less" scaling formulation under strongly stable conditions (the bulk Richardson number > 0.2). Furthermore, we show that many atmospheric chemistry models calculate ra using formulations which are inconsistent with the derivation of micro-meteorological parameters. Finally, practical implications of the differences in stability-correction algorithms are discussed for the computations of dry deposition velocities of SO2, O3 and reactive bromine compounds for specific cases of stable SBL.

  1. Response of Root Properties to Tripartite Symbiosis between Lucerne (Medicago sativa L., Rhizobia and Mycorrhiza Under Dry Organic Farming Conditions

    Directory of Open Access Journals (Sweden)

    M. R. Ardakani

    2009-01-01

    Full Text Available Problem statement: It is generally considered that root turnover is a major contributor to organic matter and mineral nutrient cycles in organic managed agroecosystems. Approach: This study designed to investigate whether microbial activity could affect on root properties of Lucerne in an organically managed field under dry weather conditions. The trial was laid out as a factorial experiment in the fields of the University of Natural Resources and Applied Life Sciences, Vienna- Austria at Raasdorf in 2007. The experimental factors of Rhizobium (Sinorhizobium meliloti and Arbuscular Mycorrhiza (AM including Glomus etunicatum, G. intraradices and G. claroideum and irrigation levels were tested. Results: Results showed that increasing water deficit affected root dry weigh, specific root mass and root length significantly at 1% level and co-inoculation of rhizobium and mycorrhiza with irrigation increased all root parameters. Datas of variance analysis for mycorrhizal colonization showed that main effect of using mycorrhiza had significant effects on root parameters at 5 and 1% probability level at first and second harvest, respectively. Results of mean comparisons by Duncans Multiple Range Test showed that mycorrhizal colonization was higher in the inoculated treatments by rhizobium, mycorrhiza and irrigated plots in both harvests. Double interaction of mycorrhiza and irrigation was higher in both harvests (37.05 and 65.73%, respectively. Conclusion: It can be suggested that the tripartite symbiosis of Rhizobium, AM and Lucerne can improve the performance of Lucerne in organic farming and under dry conditions. Such traits could be incorporated into breeding programs to improve drought tolerance especially in organic fields.

  2. Wear Behaviour of Hard Cr Coatings for Cold Forming Tools Under Dry Sliding Conditions

    Directory of Open Access Journals (Sweden)

    S. Mitrović

    2012-03-01

    Full Text Available Cr hard coatings are largely used in industry in metal cutting and cold forming processes; This work on quantitative way represents improvement, in terms of wear resistance, which is obtained by depositing Cr hard coating on foundation material. Wear testing is done on tribometer with block –on –disc contact geometry at sliding contact of Cr hard coated sample with steel disc. Testing was performed in conditions without lubrication at variable value of contact parameters (normal load, sliding speed. Cr hard coatings in all contact conditions show smaller values of wear rate.

  3. Warm Dry Weather Conditions Cause of 2016 Fort McMurray Wild Forest Fire and Associated Air Quality

    Science.gov (United States)

    de Azevedo, S. C.; Singh, R. P.; da Silva, E. A., Sr.

    2016-12-01

    The climate change is evident from the increasing temperature around the world, day to day life and increasing frequency of natural hazards. The warm and dry conditions are the cause of frequent forest fires around the globe. Forest fires severely affect the air quality and human health. Multi sensor satellites and dense network of ground stations provide information about vegetation health, meteorological, air quality and atmospheric parameters. We have carried out detailed analysis of satellite and ground data of wild forest fire that occurred in May 2016 in Fort McMurray, Alberta, Canada. This wild forest fire destroyed 10 per cent of Fort McMurray's housing and forced more than 90,000 people to evacuate the surrounding areas. Our results show that the warm and dry conditions with low rainfall were the cause of Fort McMurray wild fire. The air quality parameters (particulate matter, CO, ozone, NO2, methane) and greenhouse gases measured from Atmospheric Infrared Sounder (AIRS) satellite show enhanced levels soon after the forest fire. The emissions from the forest fire affected health of population living in surrounding areas up to 300 km radius.

  4. Screen of Different Cotton Varieties under Dry Land Conditions in Namibia

    Institute of Scientific and Technical Information of China (English)

    ALWEENDO T E; SHIPEPE B T

    2008-01-01

    @@ Cotton has been identified as a crop with promising potential in Namibia.As such,cotton variety evaluation trials have been conducted for yield,fiber qualities,resistance to diseases and pests,as well as adaptability to the climatic conditions.

  5. Investigation of impact of storage conditions on Hypericum perforatum L. dried total extract

    Directory of Open Access Journals (Sweden)

    Halil Koyu

    2015-09-01

    Full Text Available Hypericum perforatum L. (Hypericaceae has been widely prescribed for mild to moderate depression following the release of promising results in clinical trials. However, it is known that its constituents may be affected by milieu. The stability complexities of the constituents of H. perforatum have gained interest in recent years. The aim of the present study was to examine the impact of storage conditions on H. perforatum total extract simultaneously under different storage conditions. Temperature, humidity, and light conditions were evaluated. Comparative analyses of methanol extracts were conducted using high performance liquid chromatography-diode array detection for chlorogenic acid, rutin, hyperoside, isoquercitrin, quercitrin, quercetin, amentoflavone, pseudohypericin, hyperforin, and hypericin. Analysis and extraction were performed using a validated method. The fluctuation of the constituents of the plant extract has been demonstrated. Among these components, chlorogenic acid was the most stable. Hyperforin, hypericin, and pseudohypericin were more stable than the flavonoids at −20°C, in the 6th month. As estimated, decay was lowest at −20°C and highest at 40°C–75% relative humidity for the analyzed constituents. Except for hyperforin, light protection decreased the breakdown of components within 4 months. However, at the 6th month, equivalent changes were seen for all constituents. Degradation of the constituents at −20°C indicates the importance of stability tests in analysis studies covering time and storage conditions.

  6. 78 FR 19148 - Shielding and Radiation Protection Review Effort and Licensing Conditions for Dry Storage...

    Science.gov (United States)

    2013-03-29

    ...; ] NUCLEAR REGULATORY COMMISSION 10 CFR Part 72 Shielding and Radiation Protection Review Effort and...-ISG-26A), Revision 0, ``Shielding and Radiation Protection Review Effort and Licensing Conditions for... to NRC staff when reviewing the shielding and radiation protection portions of applications...

  7. A conditional extreme value theory approach in value-at-risk forecasting: Evidence from Southeastern Europe and USA market

    Directory of Open Access Journals (Sweden)

    Totić Selena

    2015-01-01

    Full Text Available As a consequence of the recent financial crisis, the adequacy of different Value-at-Risk (VaR methodologies was heavily questioned. Current practice in VaR assessment relies on modeling the whole distribution of returns. As an alternative, in this paper we model tail behavior of returns, and thus VaR, using conditional Extreme Value Theory (EVT, which combines EVT and GARCH methodology. Moreover, we examine the performance of conditional EVT with the daily returns of seven stock market indices, of which six are from Southeastern Europe (BelexLine, BET, BUX, CROBEX, SBITOP, SOFIX from the period of September 2004 - April 2013, and one from USA market (Standard&Poors 500 Index from the period January 1998 - April 2013. Backtesting of historical daily returns proves that conditional EVT model gives good predictions for all indices and for all confidence levels.

  8. Sensory profiling of Dalmatian dry-cured ham under different temperature conditions

    Directory of Open Access Journals (Sweden)

    Zlatko Janječić

    2010-01-01

    Full Text Available To investigate the influence of the Dalmatian ham processing conditions on weight loss and sensory characteristics, 20 hams were processed following different temperature conditions during salting and ripening. For that purpose, hams were evaluated using quantitative descriptive analysis. The weight loss was higher and all sensory traits except presence of tyrosine and phenylalanine crystals were higher rated for hams processed at higher temperatures. The most significant (P<0.0001 influence of temperature was established on subcutaneous fat color, muscle color and presence of tyrosine and phenylalanine, whereas no influence was established on appearance, marbling, flavor and melting. This concludes that there is overall significant effect of higher temperature on sensory characteristics most likely due to the more intense proteolysis and lipolysis.

  9. Diagnosing the Local Land-Atmosphere Coupling (LoCo) in Models and Observations: A Study of Dry/Wet Extremes in the U. S. Southern Great Plains

    Science.gov (United States)

    Santanello, J. A.; Peters-Lidard, C. D.; Kumar, S.; Dong, X.; Kennedy, A. D.

    2010-12-01

    Land-atmosphere interactions play a critical role in determining the diurnal evolution of both planetary boundary layer (PBL) and land surface temperature and moisture states. The degree of coupling between the land surface and PBL in numerical weather prediction and climate models remains largely unexplored and undiagnosed due to the complex interactions and feedbacks present across a range of scales. Further, uncoupled systems or experiments (e.g., the Project for Intercomparison of Land Parameterization Schemes, PILPS) may lead to inaccurate water and energy cycle process understanding by neglecting feedback processes such as PBL-top entrainment. In this study, a framework for diagnosing local land-atmosphere coupling (LoCo) is presented using a coupled mesoscale model with a suite of PBL and land surface model (LSM) options along with observations during the summers of 2006/7 in the U.S. Southern Great Plains. Specifically, the Weather Research and Forecasting (WRF) model has been coupled to NASA's Land Information System (LIS), which provides a flexible and high-resolution representation and initialization of land surface physics and states. A range of diagnostics exploring the links and feedbacks between soil moisture and precipitation are examined for the dry/wet extremes of this region, along with the sensitivity of PBL-LSM coupling to perturbations in soil moisture. As such, this methodology provides a potential pathway to study factors controlling local land-atmosphere coupling (LoCo) using the LIS-WRF system, which is serving as a testbed for LoCo experiments to evaluate coupling diagnostics within the community.

  10. Diagnosing the Nature of Land-Atmosphere Coupling During the 2006-7 Dry/Wet Extremes in the U.S. Southern Great Plains

    Science.gov (United States)

    Santanello, Joseph A., Jr.; Peters-Lidard, Christa D.; Kumar, Sujay V.; Dong, Xiquan; Kennedy, Aaron D.

    2011-01-01

    Land-atmosphere interactions play a critical role in determining the. diurnal evolution of both planetary boundary layer (PBL) and land surface temperature and moisture states. The degree of coupling between the land surface and PBL in numerical weather prediction and climate models remains largely unexplored and undiagnosed due to the complex interactions and feedbacks present across a range of scales. Further, uncoupled systems or experiments (e.g., the Project for Intercomparison of Land Parameterization Schemes, PILPS) may lead to inaccurate water and energy cycle process understanding by neglecting feedback processes such as PBL-top entrainment. In this study, a framework for diagnosing local land-atmosphere coupling (LoCo) is presented using a coupled mesoscale model with a suite of PBL and land surface model (LSM) options along with observations during the summers of 200617 in the U.S. Southern Great Plains. Specifically, the Weather Research and Forecasting (WRF) model has been coupled to NASA's Land Information System (LIS), which provides a flexible and high-resolution representation and initialization of land surface physics and states. A range of diagnostics exploring the links and feedbacks between soil moisture and precipitation are examined for the dry/wet extremes of this region, along with the sensitivity of PBL-LSM coupling to perturbations in soil moisture. As such, this methodology provides a potential pathway to study factors controlling local land-atmosphere coupling (LoCo) using the LIS-WRF system, which is serving as a testbed for LoCo experiments to evaluate coupling diagnostics within the community.

  11. [Deep-sea research ground for the study of living matter properties in extreme conditions].

    Science.gov (United States)

    Polikarpov, G G

    2011-01-01

    The Black Sea hollow bottom is a promising research ground in the field of deep-sea radiochemoecology and exobiology. It has turned out to be at the intersection of the earth and cosmic scientific interests such as deep-sea marine radiochemoecology from the perspective of the study of extreme biogeocenological properties of the Earth biosphere and exobiology from the standpoint of the study of life phenomena (living matter) outside the Earth biosphere, i.e. on other planets and during hypothetical transfer of spores in the outer space. The potential of this ground is substantiated with the data published by the author and co-workers on accumulation of 90Sr, 137Cs and Pu isotopes with silts of bathyal pelo-contour, on the quality of deep-sea hydrogen sulphide waters (after their contact with air) for vital functions of planktonic and benthic aerobes, as well as the species composition of marine, freshwater and terrestrial plants grown from the spores collected from the bottom sediments of the Black Sea bathyal. Discussion was based on V.I. Vernadsky's ideas about the living matter and biosphere, which allowed conclusions about the biospheric and outer space role of the described phenomena.

  12. Extreme temperatures increase the deleterious consequences of inbreeding under laboratory and semi-natural conditions

    DEFF Research Database (Denmark)

    Kristensen, Torsten Nygård; Barker, J. Stuart F.; Pedersen, Kamilla Sofie

    2008-01-01

    The majority of experimental studies of the effects of population bottlenecks on fitness are performed under laboratory conditions, which do not account for the environmental complexity that populations face in nature. In this study, we test inbreeding depression in multiple replicates of inbred...... when compared with non-inbred lines of Drosophila melanogaster under different temperature conditions. Egg-to-adult viability, developmental time and sex ratio of emerging adults are studied under low, intermediate and high temperatures under laboratory as well as semi-natural conditions. The results...... the sex ratio with more females relative to males emerging at low temperatures, suggesting that selection against males in pre-adult life stages is stronger at low temperatures. The coefficient of variation (CV) of egg-to-adult viability within and among lines is higher for inbred flies and generally...

  13. Extremal properties of conditional entropy and quantum discord for XXZ, symmetric quantum states

    Science.gov (United States)

    Yurischev, M. A.

    2017-10-01

    For the XXZ subclass of symmetric two-qubit X states, we study the behavior of quantum conditional entropy S_{cond} as a function of measurement angle θ \\in [0,π /2]. Numerical calculations show that the function S_{cond}(θ ) for X states can have at most one local extremum in the open interval from zero to π /2 (unimodality property). If the extremum is a minimum, the quantum discord displays region with variable (state-dependent) optimal measurement angle θ ^*. Such θ -regions (phases, fractions) are very tiny in the space of X-state parameters. We also discover the cases when the conditional entropy has a local maximum inside the interval (0,π /2). It is remarkable that the maxima exist in surprisingly wide regions, and the boundaries for such regions are defined by the same bifurcation conditions as for those with a minimum.

  14. Modeling heat stress effect on Holstein cows under hot and dry conditions: selection tools.

    Science.gov (United States)

    Carabaño, M J; Bachagha, K; Ramón, M; Díaz, C

    2014-12-01

    component, a constant term that is not affected by temperature, representing from 64% of the variation for SCS to 91% of the variation for milk. The second component, showing a flat pattern at intermediate temperatures and increasing or decreasing slopes for the extremes, gathered 15, 11, and 24% of the variation for fat and protein yield and SCS, respectively. This component could be further evaluated as a selection criterion for heat tolerance independently of the production level.

  15. Observations and Predictions of Wave Runup, Extreme Water Levels, and Medium-Term Dune Erosion during Storm Conditions

    Directory of Open Access Journals (Sweden)

    Serge Suanez

    2015-07-01

    Full Text Available Monitoring of dune erosion and accretion on the high-energy macrotidal Vougot beach in North Brittany (France over the past decade (2004–2014 has revealed significant morphological changes. Dune toe erosion/accretion records have been compared with extreme water level measurements, defined as the sum of (i astronomic tide; (ii storm surge; and (iii vertical wave runup. Runup parameterization was conducted using swash limits, beach profiles, and hydrodynamic (Hm0, Tm0,–1, and high tide water level—HTWL data sets obtained from high frequency field surveys. The aim was to quantify in-situ environmental conditions and dimensional swash parameters for the best calibration of Battjes [1] runup formula. In addition, an empirical equation based on observed tidal water level and offshore wave height was produced to estimate extreme water levels over the whole period of dune morphological change monitoring. A good correlation between this empirical equation (1.01Hmoξo and field runup measurements (Rmax was obtained (R2 85%. The goodness of fit given by the RMSE was about 0.29 m. A good relationship was noticed between dune erosion and high water levels when the water levels exceeded the dune foot elevation. In contrast, when extreme water levels were below the height of the toe of the dune sediment budget increased, inducing foredune recovery. These erosion and accretion phases may be related to the North Atlantic Oscillation Index.

  16. Studies of nuclei under the extreme conditions of density, temperature, isospin asymmetry and the phase diagram of hadronic matter

    Energy Technology Data Exchange (ETDEWEB)

    Mekjian, Aram [Rutgers Univ., Piscataway, NJ (United States). Dept. of Physics and Astronomy

    2016-10-18

    The main emphasis of the entire project is on issues having to do with medium energy and ultra-relativistic energy and heavy ion collisions. A major goal of both theory and experiment is to study properties of hot dense nuclear matter under various extreme conditions and to map out the phase diagram in density or chemical potential and temperature. My studies in medium energy nuclear collisions focused on the liquid-gas phase transition and cluster yields from such transitions. Here I developed both the statistical model of nuclear multi-fragmentation and also a mean field theory.

  17. Role of the tissue free amino acids in adaptation of medicinal leeches Hirudo medicinalis L., 1758 to extreme climatic conditions.

    Science.gov (United States)

    Chernaya, L V; Kovalchuk, L A; Nokhrina, E S

    2016-01-01

    The first comparison of the spectra of free amino acids in tissues of the medicinal leeches H. medicinalis from different climatic and geographical Eurasian areas has been performed. Adaptation of H. medicinalis to extreme climatic conditions occurs via intensification of the amino acid metabolism resulting from a significant increase in the content of essential amino acids. Accumulation of arginine, histidine, and lysine (3.6-, 3.9-, and 2.0-fold increases, respectively) has proved to play a special protective role in adaptation of H. medicinalis to the low positive temperatures.

  18. Surrounding rock deformation regularity of roadway under extremely complicated geological conditions in deep mine and its control

    Institute of Scientific and Technical Information of China (English)

    刘长友; 何卓军; 万志军

    2003-01-01

    By combining the practices of deep mine mining in Changguang Mine field and using the Universal Distinct Element Code 3.0(UDEC3.0) numerical computing method, the distribution characteristics of deformation field and stress field as well as the surrounding rock deformation regularity of soft rock roadway are analyzed under extremely complicated geological conditions, a technical principle of bolting to control the surrounding rock of roadway is put forward. And also using a dynamic control for surrounding rocks designing method, the supporting parameters and implement plan are rationally determined. The experimental tests have obtained a good controlling result of surrounding rock.

  19. The microbial sulfur cycle at extremely haloalkaline conditions of soda lakes

    Directory of Open Access Journals (Sweden)

    Dimitry Y Sorokin

    2011-03-01

    Full Text Available Microbial sulfur cycle is among the most active in soda lakes. Oxidative part of the cycle is driven by chemolithoautotrophic haloalkaliphilic sulfur-oxidizing bacteria. They are present at high number of up to 106 viable cells/cm3 and represented by four genera within the Gammaproteobacteria, Thioalkalivibrio, Thioalkalimicrobium, Thioalkalispira and Thioalkalibacter. The genus Thioalkalivibrio is the most physiologically diverse and covers whole spectrum of salt/pH conditions present in soda lakes. The dominant subgroup of this genus is able to grow in saturated soda brines containing 4 M total Na+ - a unique property for any known aerobic chemolithoautotrophs. Some of the species can use thiocyanate as a sole energy source and 3 species out of 9 can grow anaerobically with nitrogen oxides. The reductive part of the cycle is also active in anoxic sediments of various soda lakes. In situ and laboratory experiments showed high sulfate reduction rates only hampered at salt-saturated conditions. The highest rates of sulfidogenesis were observed with elemental sulfur followed by thiosulfate. Formate was the most efficient electron donor with all three sulfur electron acceptors, while acetate was only utilized as an electron donor at sulfur-reducing conditions. The soda lake sulfidogenesis showed obligately alkaliphilic pH response matching the in situ conditions. Microbiological analysis showed a domination of three groups of haloalkaliphilic autotrophic SRB belonging to the order Desulfovibrionales with a clear tendency to grow by thiosulfate disproportionation even at salt-saturating conditions. Few novel representatives of the order Desulfobacterales capable of heterotrophic growth with VFA and alcohols at high pH and moderate salinity have also been found, while acetate oxidation was a function of a specialized group of haloalkaliphilic sulfur-reducing bacteria belonging to the phylum Chrysiogenetes.

  20. Penetration Depth Measurements Using a Tunnel Diode Oscillator in Extreme Conditions

    Science.gov (United States)

    Agosta, Charles C.

    2004-03-01

    The tunnel diode oscillator (TDO) has been used as a tool in condensed matter physics for over 30 years. We will discuss the application of the TDO to measure rf penetration depth in small metallic and superconducting samples in the range of 10 -1500 MHz. Our technique involves placing a sample in or on the inductor of a self-resonant tank circuit powered by a tunnel diode, and measuring the impedance of the sample by recording the frequency and amplitude shift as a function of magnetic field or temperature. This technique is very sensitive to the properties of the electrons in a sample, does not require contacts on a sample, can be used for arbitrarily small samples, is very compatible with pulsed magnetic fields, and works well in pressure cells. We will begin by giving a brief history of the TDO in condensed matter physics. We will describe the electronic theory of the TDO showing the important parameters necessary to keep the circuit stable and oscillating in different venues such as very low temperatures and pulsed magnetic fields. We will also describe some of the trade offs between stability and sensitivity in these extreme environments. We will then discuss how to interpret the data produced by the TDO, concentrating on the description of rf penetration in metallic and type II superconducting samples. Finally, as examples of the power of this TDO method, we will show Fermi surface measurements, type II superconducting phase diagrams, including details of the vortex system, and very recent results showing evidence of an inhomogeneous superconducting state. Support for this project has come from the NHMFL and the NSF

  1. Transformation and accumulation of PAH and bound residues in soil under extreme conditions - a risk assessment approach

    Science.gov (United States)

    Eschenbach, Annette

    2010-05-01

    The degradation of PAH in contaminated soil does not proceed completely in the majority of cases. However microorganisms which are able to degrade PAH are present in PAH-contaminated soils normally. A total degradation of PAH in contaminated soils is often limited by a lack of bioavailability, which results from a lack of mass transfer. The analytical depletion of contaminants in soil is not only based on degradation processes but also on a fixation or immobilization of the xenobiotic substances as stronger adsorbed to or bound residues in the soil matrix. These bound residues were verified by using 14C-labelled PAH in different soil samples. To evaluate the long term fate of theses PAH-residues the stability and transformation of 14C-labelled non-extractable PAH-residues was investigated in detail under different extreme ecological and climate conditions such as biological stress, freezing and thawing cycles, and chemical worst case conditions. The transformation and remobilization of non-extractable PAH-residues was observed in long-time experiments and was very limited in general (Eschenbach et al. 2001). Only small amounts of non extractable residues were transformed and converted to CO2 and thereby detoxified. However the treatment with a complexing agent led to an increase of extractable 14C-activity. In a further set of experiments the long term risk of a groundwater contamination was assessed. Therefore the elution rate of 14C-PAH was investigated by a routinely usable column test system. It was found that the PAH elution was not solely controlled by desorption processes. The extractable PAH concentrations and elution rates were affected by the mineralization and formation of bound residues as well. For the assessment of the maximum PAH release rate the soil material was treated by extreme and worst case conditions as well. The impact of the elution of bidestillated water, of repeated freeze-thaw cycles and a simulation of acidic rain was investigated. The

  2. Effect of live and dry food on rearing of tench (Tinca tinca L. larvae under controlled conditions

    Directory of Open Access Journals (Sweden)

    Daniel Żarski

    2011-01-01

    Full Text Available In the current paper we present a method of rearing tench (Tinca tinca L. larvae under controlled conditions, fed on dry food (Gemma and Perla and Artemia nauplii or decapsulated cysts of Artemia. Tench larvae were obtained after artificial spawning by aid of Ovopel stimulation. Two experiments were conducted during which fish were divided into 4 groups (in duplicate and placed in 30 dm3 glass fish tanks set up in a recirculating system. The fish were fed ad libitum and reared for 25 days. Larvae were fed exclusively (experiment 1 or after 10 days (experiment 2 of receiving Artemia nauplii with two types of compound feeds and decapsulated cysts of Artemia. The best growth rate was observed in the control group fed on Artemia nauplii and in the group offered decapsulated cysts in both experiments. The highest survival rate, over 96%, occurred in the control group. A twofold worse survival rate was obtained in the group fed exclusively on dry food. Applied transition schedule had significant effect on survival rate among treatments, however it did not influence the percentage of body deformations occurring in groups receiving compound feed only. The results obtained indicate the necessity of applying gradual transition from live food to compound feed and the improvement of feeding schedules in common tench culture.

  3. Contrasting Hydraulic Strategies during Dry Soil Conditions in Quercus rubra and Acer rubrum in a Sandy Site in Michigan

    Directory of Open Access Journals (Sweden)

    Julia E. Thomsen

    2013-12-01

    Full Text Available Correlation analyses were carried out for the dynamics of leaf water potential in two broad-leaf deciduous tree species in a sandy site under a range of air vapor pressure deficits and a relatively dry range of soil conditions. During nights when the soil is dry, the diffuse-porous, isohydric and shallow-rooted Acer rubrum does not recharge its xylem and leaf water storage to the same capacity that is observed during nights when the soil is moist. The ring-porous, deep-rooted Quercus rubra displays a more anisohydric behavior and appears to be capable of recharging to capacity at night-time even when soil moisture at the top 1 m is near wilting point, probably by accessing deeper soil layers than A. rubrum. Compared to A. rubrum, Q. rubra displays only a minimal level of down-regulation of stomatal conductance, which leads to a reduction of leaf water potential during times when vapor pressure deficit is high and soil moisture is limiting. We determine that the two species, despite typically being categorized by ecosystem models under the same plant functional type—mid-successional, temperate broadleaf—display different hydraulic strategies. These differences may lead to large differences between the species in water relations, transpiration and productivity under different precipitation and humidity regimes.

  4. Effect of live and dry food on rearing of tench (Tinca tinca L. larvae under controlled conditions

    Directory of Open Access Journals (Sweden)

    Andrzej Mamcarz

    2011-03-01

    Full Text Available In the current paper we present a method of rearing tench (Tinca tinca L. larvae under controlled conditions, fed on dry food (Gemma and Perla and Artemia nauplii or decapsulated cysts of Artemia. Tench larvae were obtained after artificial spawning by aid of Ovopel stimulation. Two experiments were conducted during which fish were divided into 4 groups (in duplicate and placed in 30 dm3 glass fish tanks set up in a recirculating system. The fish were fed ad libitum and reared for 25 days. Larvae were fed exclusively (experiment 1 or after 10 days (experiment 2 of receiving Artemia nauplii with two types of compound feeds and decapsulated cysts of Artemia. The best growth rate was observed in the control group fed on Artemia nauplii and in the group offered decapsulated cysts in both experiments. The highest survival rate, over 96%, occurred in the control group. A twofold worse survival rate was obtained in the group fed exclusively on dry food. Applied transition schedule had significant effect on survival rate among treatments, however it did not influence the percentage of body deformations occurring in groups receiving compound feed only. The results obtained indicate the necessity of applying gradual transition from live food to compound feed and the improvement of feeding schedules in common tench culture.

  5. Evaluation of surface detail reproduction, dimensional stability and gypsum compatibility of monophase polyvinyl-siloxane and polyether elastomeric impression materials under dry and moist conditions.

    Science.gov (United States)

    Vadapalli, Sriharsha Babu; Atluri, Kaleswararao; Putcha, Madhu Sudhan; Kondreddi, Sirisha; Kumar, N Suman; Tadi, Durga Prasad

    2016-01-01

    This in vitro study was designed to compare polyvinyl-siloxane (PVS) monophase and polyether (PE) monophase materials under dry and moist conditions for properties such as surface detail reproduction, dimensional stability, and gypsum compatibility. Surface detail reproduction was evaluated using two criteria. Dimensional stability was evaluated according to American Dental Association (ADA) specification no. 19. Gypsum compatibility was assessed by two criteria. All the samples were evaluated, and the data obtained were analyzed by a two-way analysis of variance (ANOVA) and Pearson's Chi-square tests. When surface detail reproduction was evaluated with modification of ADA specification no. 19, both the groups under the two conditions showed no significant difference statistically. When evaluated macroscopically both the groups showed statistically significant difference. Results for dimensional stability showed that the deviation from standard was significant among the two groups, where Aquasil group showed significantly more deviation compared to Impregum group (P impregum and aquasil performed better in dry condition than in moist; impregum performed better than aquasil in both the conditions. When tested for surface detail reproduction according to ADA specification, under dry and moist conditions both of them performed almost equally. When tested according to macroscopic evaluation, impregum and aquasil performed significantly better in dry condition compared to moist condition. In dry condition, both the materials performed almost equally. In moist condition, aquasil performed significantly better than impregum. Regarding gypsum compatibility according to ADA specification, in dry condition both the materials performed almost equally, and in moist condition aquasil performed better than impregum. When tested by macroscopic evaluation, impregum performed better than aquasil in both the conditions.

  6. Friction and wear of HNBR with different fillers under dry rolling and sliding conditions

    Directory of Open Access Journals (Sweden)

    2009-02-01

    Full Text Available Peroxide cured hydrogenated acrylonitrile/butadiene rubber (HNBR compounds with 20 parts per hundred rubber (phr active fillers, such as carbon black (CB, multiwall carbon nanotube (MWCNT and silica were produced and their friction and wear properties under unlubricated rolling and sliding conditions were evaluated. The network-related properties of the HNBR compounds were deduced from dynamic-mechanical thermal analysis (DMTA. The coefficient of friction (COF and the specific wear rate (Ws were determined in different home-made test rigs. The CB and MWCNT containing HNBR compounds exhibited the best resistance to rolling and sliding wear, respectively, among the HNBR systems studied. The worn surfaces were inspected in scanning electron microscope (SEM and the wear mechanisms were analyzed and discussed in respect to the types of wear and fillers.

  7. EFFECTS OF EXTREME AND UNUSUAL CONDITIONS ON LANA ALLOYS: INTERIM REPORT, FY14 (U)

    Energy Technology Data Exchange (ETDEWEB)

    Shanahan, Kirk L.

    2014-04-25

    The TTP proposed research aimed at determining: a) the rate at which these changes occurred and the effect of initial conditions, especially in the early phases of Hydrogen Heat Treatment (HHT), b) whether or not different LANA alloys would show similar effects, and c) whether common contaminants/poisons impacted LANA alloy hydride chemistry similarly to what had been found for Pd and Pd-alloy hydride chemistry.

  8. Novel portable press for synchrotron time-resolved 3-D micro-imagining under extreme conditions

    Energy Technology Data Exchange (ETDEWEB)

    Philippe, J.; Le Godec, Y., E-mail: yann.legodec@impmc.upmc.fr; Bergame, F.; Morand, M. [IMPMC, Université Pierre et Marie Curie, Paris (France); Mezouar, M.; Bauchau, S.; Alvarez-Murga, M. [European Synchrotron Radiation Facility, Grenoble (France); Perrillat, J. P. [Laboratoire de Géologie de Lyon, Université Claude Bernard Lyon1, Lyon (France); Bromiley, G.; Berg, M. [School of GeoSciences, University of Edinburgh, Edinburgh (United Kingdom); King, A.; Guignot, N.; Itié, J. P. [Synchrotron SOLEIL, St Aubin France (France); Atwood, Robert [Diamond Light Source Ltd., Harwell Science and Innovation Campus, Didcot (United Kingdom)

    2016-07-27

    Here we present the instrumental development to extend the synchrotron X-ray microtomography techniques to in situ studies under static compression (HP) or shear stress or the both conditions at high temperatures (HT). To achieve this, a new rotating tomography Paris-Edinburgh cell (rotoPEc) has been developed. This ultra-compact portable device, easily and successfully adapted to various multi-modal synchrotron experimental set-up at ESRF, SOLEIL and DIAMOND is explained in detail.

  9. MECHANICAL STRENGTH RESPONSES OF POLED LEAD ZIRCONATE TITANATE UNDER EXTREME ELECTRIC FIELD AND VARIOUS TEMPERATURE CONDITIONS

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Hong [ORNL; Matsunaga, Tadashi [ORNL; Zhang, Kewei [ORNL; Lin, Hua-Tay [ORNL; Wereszczak, Andrew A [ORNL

    2016-01-01

    PZT (lead zirconate titanate), particularly PZT-5A, is used in a variety of critical actuation and sensing systems because of its high Curie temperature and large piezoelectric coefficients. However, PZT is susceptible to mechanical failure. The evaluation of the mechanical strength of the material under the target working conditions is very important. This study presents part of the recent experimental developments in mechanical testing and evaluation of PZT materials at Oak Ridge National Laboratory. Ball-on-ring and four-point bending testing setups were used, with modifications made to account for testing requirements from high-level electric field and elevated temperature. The poled PZT-5A or equivalent material was tested under various specimen and testing conditions. The parameters of the distribution of strengths (characteristic strength and Weibull modulus) are discussed in relation to the testing conditions. Fractographic results based on scanning electron microscopy are also presented and discussed. The related data can serve as input for the design of piezoceramic devices, not only those used in energy systems like fuel injectors in heavy-duty diesel engines, but also those used in structural health monitoring, energy harvesting, and other critical systems in aerospace and civil engineering.

  10. Roles of Arbuscular Mycorrhizal Fungi and Soil Abiotic Conditions in the Establishment of a Dry Grassland Community.

    Directory of Open Access Journals (Sweden)

    Jana Knappová

    Full Text Available The importance of soil biota in the composition of mature plant communities is commonly acknowledged. In contrast, the role of soil biota in the early establishment of new plant communities and their relative importance for soil abiotic conditions are still poorly understood.The aim of this study was to understand the effects of soil origin and soil fungal communities on the composition of a newly established dry grassland plant community. We used soil from two different origins (dry grassland and abandoned field with different pH and nutrient and mineral content. Grassland microcosms were established by sowing seeds of 54 species of dry grassland plants into the studied soils. To suppress soil fungi, half of the pots were regularly treated with fungicide. In this way, we studied the independent and combined effects of soil origin and soil community on the establishment of dry grassland communities.The effect of suppressing the soil fungal community on the richness and composition of the plant communities was much stronger than the effect of soil origin. Contrary to our expectations, the effects of these two factors were largely additive, indicating the same degree of importance of soil fungal communities in the establishment of species-rich plant communities in the soils from both origins. The negative effect of suppressing soil fungi on species richness, however, occurred later in the soil from the abandoned field than in the soil from the grassland. This result likely occurred because the negative effects of the suppression of fungi in the field soil were caused mainly by changes in plant community composition and increased competition. In contrast, in the grassland soil, the absence of soil fungi was limiting for plants already at the early stages of their establishment, i.e., in the phases of germination and early recruitment. While fungicide affects not only arbuscular mycorrhizal fungi but also other biota, our data indicate that changes

  11. Extreme Hypoxic Conditions Induce Selective Molecular Responses and Metabolic Reset in Detached Apple Fruit

    Science.gov (United States)

    Cukrov, Dubravka; Zermiani, Monica; Brizzolara, Stefano; Cestaro, Alessandro; Licausi, Francesco; Luchinat, Claudio; Santucci, Claudio; Tenori, Leonardo; Van Veen, Hans; Zuccolo, Andrea; Ruperti, Benedetto; Tonutti, Pietro

    2016-01-01

    The ripening physiology of detached fruit is altered by low oxygen conditions with profound effects on quality parameters. To study hypoxia-related processes and regulatory mechanisms, apple (Malus domestica, cv Granny Smith) fruit, harvested at commercial ripening, were kept at 1°C under normoxic (control) and hypoxic (0.4 and 0.8 kPa oxygen) conditions for up to 60 days. NMR analyses of cortex tissue identified eight metabolites showing significantly different accumulations between samples, with ethanol and alanine displaying the most pronounced difference between hypoxic and normoxic treatments. A rapid up-regulation of alcohol dehydrogenase and pyruvate-related metabolism (lactate dehydrogenase, pyruvate decarboxylase, alanine aminotransferase) gene expression was detected under both hypoxic conditions with a more pronounced effect induced by the lowest (0.4 kPa) oxygen concentration. Both hypoxic conditions negatively affected ACC synthase and ACC oxidase transcript accumulation. Analysis of RNA-seq data of samples collected after 24 days of hypoxic treatment identified more than 1000 genes differentially expressed when comparing 0.4 vs. 0.8 kPa oxygen concentration samples. Genes involved in cell-wall, minor and major CHO, amino acid and secondary metabolisms, fermentation and glycolysis as well as genes involved in transport, defense responses, and oxidation-reduction appeared to be selectively affected by treatments. The lowest oxygen concentration induced a higher expression of transcription factors belonging to AUX/IAA, WRKY, HB, Zinc-finger families, while MADS box family genes were more expressed when apples were kept under 0.8 kPa oxygen. Out of the eight group VII ERF members present in apple genome, two genes showed a rapid up-regulation under hypoxia, and western blot analysis showed that apple MdRAP2.12 proteins were differentially accumulated in normoxic and hypoxic samples, with the highest level reached under 0.4 kPa oxygen. These data suggest

  12. Extreme hypoxic conditions induce selective molecular responses and metabolic reset in detached apple fruit

    Directory of Open Access Journals (Sweden)

    Dubravka eCukrov

    2016-02-01

    Full Text Available The ripening physiology of detached fruit is altered by low oxygen conditions with profound effects on quality parameters. To study hypoxia-related processes and regulatory mechanisms, apple (Malus domestica, cv Granny Smith fruit, harvested at commercial ripening, were kept at 1°C under normoxic (control and hypoxic (0.4 and 0.8 kPa oxygen conditions for up to 60 days. NMR analyses of cortex tissue identified eight metabolites showing significantly different accumulations between samples, with ethanol and alanine displaying the most pronounced difference between hypoxic and normoxic treatments A rapid up-regulation of alcohol dehydrogenase and pyruvate-related metabolism (lactate dehydrogenase, pyruvate decarboxylase, alanine aminotransferase gene expression was detected under both hypoxic conditions with a more pronounced effect induced by the lowest (0.4 kPa oxygen concentration. Both hypoxic conditions negatively affected ACC synthase and ACC oxidase transcript accumulation. Analysis of RNA-seq data of samples collected after 24 days of hypoxic treatment identified more than 1,000 genes differentially expressed when comparing 0.4 vs 0.8 kPa oxygen concentration samples. Genes involved in cell-wall, minor and major CHO, amino acid and secondary metabolisms, fermentation and glycolysis as well as genes involved in transport, defense responses and oxidation-reduction appeared to be selectively affected by treatments. The lowest oxygen concentration induced a higher expression of transcription factors belonging to AUX/IAA, WRKY, HB, Zinc-finger families, while MADS box family genes were more expressed when apples were kept under 0.8 kPa oxygen. Out of the eight group VII ERF members present in apple genome, two genes showed a rapid up-regulation under hypoxia, and western blot analysis showed that apple MdRAP2.12 proteins were differentially accumulated in normoxic and hypoxic samples, with the highest level reached under 0.4 kPa oxygen. These

  13. Extreme climatic conditions and health service utilisation across rural and metropolitan New South Wales

    Science.gov (United States)

    Jegasothy, Edward; McGuire, Rhydwyn; Nairn, John; Fawcett, Robert; Scalley, Benjamin

    2017-03-01

    Periods of successive extreme heat and cold temperature have major effects on human health and increase rates of health service utilisation. The severity of these events varies between geographic locations and populations. This study aimed to estimate the effects of heat waves and cold waves on health service utilisation across urban, regional and remote areas in New South Wales (NSW), Australia, during the 10-year study period 2005-2015. We divided the state into three regions and used 24 over-dispersed or zero-inflated Poisson time-series regression models to estimate the effect of heat waves and cold waves, of three levels of severity, on the rates of ambulance call-outs, emergency department (ED) presentations and mortality. We defined heat waves and cold waves using excess heat factor (EHF) and excess cold factor (ECF) metrics, respectively. Heat waves generally resulted in increased rates of ambulance call-outs, ED presentations and mortality across the three regions and the entire state. For all of NSW, very intense heat waves resulted in an increase of 10.8% (95% confidence interval (CI) 4.5, 17.4%) in mortality, 3.4% (95% CI 0.8, 7.8%) in ED presentations and 10.9% (95% CI 7.7, 14.2%) in ambulance call-outs. Cold waves were shown to have significant effects on ED presentations (9.3% increase for intense events, 95% CI 8.0-10.6%) and mortality (8.8% increase for intense events, 95% CI 2.1-15.9%) in outer regional and remote areas. There was little evidence for an effect from cold waves on health service utilisation in major cities and inner regional areas. Heat waves have a large impact on health service utilisation in NSW in both urban and rural settings. Cold waves also have significant effects in outer regional and remote areas. EHF is a good predictor of health service utilisation for heat waves, although service needs may differ between urban and rural areas.

  14. Role of the Atlantic Multidecadal Variability on extreme climate conditions over North America

    Science.gov (United States)

    Ruprich-Robert, Yohan; Delworth, Thomas; Msadek, Rym; Castruccio, Frederic; Yeager, Stephen; Danabasoglu, Gokhan

    2017-04-01

    The Atlantic Multidecadal Variability (AMV) is associated with marked modulations of climate anomalies observed over many areas of the globe like droughts, decline in sea ice or changes in the atmospheric circulation. However, the shortness of the historical observations compared to the AMV period ( 60-80yr) makes it difficult to show that the AMV is a direct driver of these variations. To isolate the AMV climate response, we use a suite of global coupled models from GFDL and NCAR, in which the North Atlantic sea surface temperatures are restored to the observed AMV pattern, while the other ocean basins are left fully coupled. In order to explore and robustly isolate the AMV impacts on extreme events, we use large ensemble simulations (between 30 and 100 members depending on the model) that are integrated for 10 years. We investigate the importance of model resolution by analyzing GFDL models that vary in their atmospheric resolution and we assess the robustness of the results by comparing them to similar experiments performed with the NCAR coupled model. Further, we investigate the influence of model surface temperature biases on the simulated AMV teleconnections using a flux-adjusted experiment based on a model configuration that corrects for momentum, enthalpy and freshwater fluxes. We focus in this presentation on the impact of the AMV on the occurrence of the North American heat waves. We find that the AMV modulates by about 30% the occurrence of heat waves over North Mexico and the South-West of USA, with more heat waves during a warm phase of the AMV. The main reason for such an increase is that, during a warm AMV phase, the anomalously warm sea surface temperature leads to an increase of the atmospheric convection over the tropical Atlantic, as well as to a an anomalous downward motion over North America. This atmospheric response to AMV inhibits the precipitation over there and drives a deficit of soil moisture. In the summer, the latent heat of

  15. FUNCTIONAL STATE OF ORGANISM OF INTERN DOCTORS WITH DIFFERENT SUCCESS LEVEL ACTIVITY IN EXTREME CONDITIONS IN THE COURSE OF DAILY DUTY IN CLINIC

    Directory of Open Access Journals (Sweden)

    L.K. Madzigon

    2008-09-01

    Full Text Available In the course of daily duty in clinic, the indeces of functional status, functional reserve of organism and mnestic (operator’s performance ability of intern doctors with different success level activity in extreme conditions were determined twice (in the beginning and at the end of the duty. It is shown that the higher success level activity in extreme conditions of interns, the more tolerance and strength of their body functional system formed in work process and it means the higher professional activity performance. Intern graduates activity preparation in extreme conditions is one of activities of Medical Institutions of Higher Education quality improvement

  16. Explosive Chemistry: Simulating the Chemistry of Energetic Materials at Extreme Conditions

    Energy Technology Data Exchange (ETDEWEB)

    Reed, E J; Manaa, M R; Fried, L E

    2003-11-18

    In the brief instant of a high-explosive detonation, the shock wave produces a pressure 500,000 times that of the Earth's atmosphere, the detonation wave travels as fast as 10 kilometers per second, and internal temperatures soar up to 5,500 Kelvin. As the shock propagates through the energetic material, the rapid heating coupled with compression that results in almost 30% volume reduction, initiate complex chemical reactions. A dense, highly reactive supercritical fluid is established behind the propagating detonation front. Energy release from the exothermic chemical reactions serve in turn to drive and sustain the detonation process until complete reactivity is reached. Several experimental results suggest the existence of strong correlations between the applied mechanical stress and shocks, the local heterogeneity and defects (dislocations, vacancies, cracks, impurities, etc.), and the onset of chemical reactions. The reaction chemistry of energetic materials at high pressure and temperature is, therefore, of considerable importance in understanding processes that these materials experience under impact and detonation conditions. Chemical decomposition models are critical ingredients in order to predict, among other things, the measured times to explosion and the conditions for ignition of hot spots, localized regions of highly concentrated energy associated with defects. To date, chemical kinetic rates of condense-phase energetic materials at detonation conditions are virtually non-existent, and basic questions such as: (a) which bond in a given energetic molecule breaks first, and (b) what type of chemical reactions (unimolecular versus bimolecular, etc.) that dominate early in the decomposition process, are still largely unknown.

  17. Surface and tribological behaviors of the bioinspired polydopamine thin films under dry and wet conditions.

    Science.gov (United States)

    Zhang, Wei; Yang, Fut K; Han, Yougun; Gaikwad, Ravi; Leonenko, Zoya; Zhao, Boxin

    2013-02-11

    Dopamine is a "sticky" biomolecule containing the typical functional groups of mussel adhesive proteins. It can self-polymerize into a nanoscale thin film on various surfaces. We investigated the surface, adhesion, friction, and cracking properties of polydopamine (PDA) thin films for their effective transfer to functional devices and biocompatible coatings. A series of surface characterizations and mechanical tests were performed to reveal the static and dynamic properties of PDA films coated on glass, polydimethylsiloxane (PDMS), and epoxy. We found that PDA films are highly hydrated under wet conditions because of their porous membrane-like nanostructures and hydrophilic functional groups. Upon dehydration, the films form cracks when they are coated on soft substrates due to internal stresses and the large mismatch in elastic modulus. The adhesive pull-off force or the effective work of adhesion increased with the contact time, suggesting dynamic interactions at the interface. A significant decrease in friction forces in water was observed on all three material surfaces coated with PDA; thus, the film might serve as a water-based lubrication coating. We attributed the different behavior of PDA films in air and in water to its hydration effects. These research findings provide insight into the stability, mechanical, and adhesive properties of the PDA films, which are critical for their applications.

  18. SIPEX 2012: Extreme sea-ice and atmospheric conditions off East Antarctica

    Science.gov (United States)

    Heil, P.; Stammerjohn, S.; Reid, P.; Massom, R. A.; Hutchings, J. K.

    2016-09-01

    In 2012, Antarctic sea-ice coverage was marked by weak annual-mean climate anomalies that consisted of opposing anomalies early and late in the year (some setting new records) which were interspersed by near-average conditions for most of the austral autumn and winter. Here, we investigate the ocean-ice-atmosphere system off East Antarctica, prior to and during the Sea Ice Physics and Ecosystems eXperiment [SIPEX] 2012, by exploring relationships between atmospheric and oceanic forcing together with the sea-ice and snow characteristics. During August and September 2012, just prior to SIPEX 2012, atmospheric circulation over the Southern Ocean was near-average, setting up the ocean-ice-atmosphere system for near-average conditions. However, below-average surface pressure and temperature as well as strengthened circumpolar winds prevailed during June and July 2012. This led to a new record (19.48×106 km2) in maximum Antarctic sea-ice extent recorded in late September. In contrast to the weak circum-Antarctic conditions, the East Antarctic sector (including the SIPEX 2012 region) experienced positive sea-ice extent and concentration anomalies during most of 2012, coincident with negative atmospheric pressure and sea-surface temperature anomalies. Heavily deformed sea ice appeared to be associated with intensified wind stress due to increased cyclonicity as well as an increased influx of sea ice from the east. This increased westward ice flux is likely linked to the break-up of nearly 80% of the Mertz Glacier Tongue in 2010, which strongly modified the coastal configuration and hence the width of the westward coastal current. Combined with favourable atmospheric conditions the associated changed coastal configuration allowed more sea ice to remain within the coastal current at the expense of a reduced northward flow in the region around 141°-145°E. In addition a westward propagating positive anomaly of sea-ice extent from the western Ross Sea during austral winter

  19. An archaeal tRNA-synthetase complex that enhances aminoacylation under extreme conditions

    DEFF Research Database (Denmark)

    Godinic-Mikulcic, Vlatka; Jaric, Jelena; Hausmann, Corinne D;

    2011-01-01

    Aminoacyl-tRNA synthetases (aaRSs) play an integral role in protein synthesis, functioning to attach the correct amino acid with its cognate tRNA molecule. AaRSs are known to associate into higher-order multi-aminoacyl-tRNA synthetase complexes (MSC) involved in archaeal and eukaryotic translation...... in the catalytic efficiency of serine attachment to tRNA, but had no effect on the activity of MtArgRS. Further, the most pronounced improvements in the aminoacylation activity of MtSerRS induced by MtArgRS were observed under conditions of elevated temperature and osmolarity. These data indicate that formation...

  20. Quantification of Cation Sorption to Engineered Barrier Materials Under Extreme Conditions

    Energy Technology Data Exchange (ETDEWEB)

    Powell, Brian [Clemson Univ., SC (United States); Schlautman, Mark [Clemson Univ., SC (United States); Rao, Linfeng [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Nitsche, Heino [Univ. of California, Berkeley, CA (United States); Gregorich, Kenneth [Univ. of California, Berkeley, CA (United States)

    2016-02-02

    The objective of this research is to examine mechanisms and thermodynamics of actinide sorption to engineered barrier materials (iron (oxyhydr)oxides and bentonite clay) for nuclear waste repositories under high temperature and high ionic strength conditions using a suite of macroscopic and microscopic techniques which will be coupled with interfacial reaction models. Gaining a mechanistic understanding of interfacial processes governing the sorption/sequestration of actinides at mineral-water interfaces is fundamental for the accurate prediction of actinide behavior in waste repositories. Although macroscale sorption data and various spectroscopic techniques have provided valuable information regarding speciation of actinides at solid-water interfaces, significant knowledge gaps still exist with respect to sorption mechanisms and the ability to quantify sorption, particularly at high temperatures and ionic strengths. This objective is addressed through three major tasks: (1) influence of oxidation state on actinide sorption to iron oxides and clay minerals at elevated temperatures and ionic strengths; (2) calorimetric titrations of actinide-mineral suspensions; (3) evaluation of bentonite performance under repository conditions. The results of the work will include a qualitative conceptual model and a quantitative thermodynamic speciation model describing actinide partitioning to minerals and sediments, which is based upon a mechanistic understanding of specific sorption processes as determined from both micro-scale and macroscale experimental techniques. The speciation model will be a thermodynamic aqueous and surface complexation model of actinide interactions with mineral surfaces that is self-consistent with macroscopic batch sorption data, calorimetric and potentiometric titrations, X-ray absorption Spectroscopy (XAS, mainly Extended X-ray Absorption Fine Structure (EXAFS)), and electron microscopy analyses. The novelty of the proposed work lies largely in

  1. Laboratory measurements of materials in extreme conditions; The use of high energy radiation sources for high pressure studies

    Energy Technology Data Exchange (ETDEWEB)

    Cauble, R.; Remington, B.A.

    1998-06-01

    High energy lasers can be used to study material conditions that are appropriate fort inertial confinement fusion: that is, materials at high densities, temperatures, and pressures. Pulsed power devices can offer similar opportunities. The National Ignition Facility (NIF) will be a high energy multi-beam laser designed to achieve the thermonuclear ignition of a mm-scale DT-filled target in the laboratory. At the same time, NE will provide the physics community with a unique tool for the study of high energy density matter at states unreachable by any other laboratory technique. Here we describe how these lasers and pulsed power tools can contribute to investigations of high energy density matter in the areas of material properties and equations of state, extend present laboratory shock techniques such as high-speed jets to new regimes, and allow study of extreme conditions found in astrophysical phenomena.

  2. Effect of bionic coupling units' forms on wear resistance of gray cast iron under dry linear reciprocating sliding condition

    Science.gov (United States)

    Pang, Zuobo; Zhou, Hong; Xie, Guofeng; Cong, Dalong; Meng, Chao; Ren, Luquan

    2015-07-01

    In order to get close to the wear form of guide rails, the homemade linear reciprocating wear testing machine was used for the wear test. In order to improve the wear-resistance of gray cast iron guide rail, bionic coupling units of different forms were manufactured by a laser. Wear behavior of gray-cast-iron with bionic-coupling units has been studied under dry sliding condition at room temperature using the wear testing machine. The wear resistance was evaluated by means of weight loss measurement and wear morphology. The results indicated that bionic coupling unit could improve the wear resistance of gray cast iron. The wear resistance of gray cast iron with reticulation bionic coupling unit is the best. When the load and speed changed, reticulation bionic coupling unit still has excellent performance in improving the wear resistance of gray cast iron.

  3. A New Force-Matched Reactive Force Field for Bulk Water Under Extreme Thermodynamic Conditions

    Science.gov (United States)

    Fried, Laurence; Koziol, Lucas

    2015-06-01

    A many-body classical force field is presented for water under dissociative thermodynamic conditions. The force field is optimized by force-matching to ab initio molecular dynamics (AIMD) simulations calculated with Density Functional Theory (DFT). The force field contains short-ranged central and many-body over-coordination terms, and long-range Ewald electrostatics. It is optimized and tested on water at density 1.5 g/mL and 2000 K, which is approximately 10% dissociated according to DFT. Molecular dynamics simulations closely reproduce DFT radial distribution functions, as well as the distribution of wat and dissociation products. The calculated atomic self-diffusion constants appear about 50% lower than in DFT, although precise comparison is impossible due to the short timescale accessible to AIMD (about 20 ps). The force field is also compared to ReaxFF using the CHO parameter set of Chenowith et al. ReaxFF structural and dynamical properties are in overall fair agreement with DFT, although ReaxFF water is not dissociative at these conditions. This work was performed under the auspices of the U.S. Department of Energy by Lawrence Livermore National Laboratory under Contract DE-AC52-07NA27344.

  4. Synchrotron Radiation and High Pressure: New Light on Materials Under Extreme Conditions

    Science.gov (United States)

    Hemley, Russell

    2005-03-01

    Current technological advances now make it possible to perform experiments on materials subjected to static or sustained conditions up to multimegabar pressures (>300 GPa) and from cryogenic temperatures to several thousand degrees (˜0.5 eV range). With these techniques, densities of condensed matter can be increased over an order of magnitude, causing numerous transformations and new physical and chemical phenomena to occur. Growth in this area largely been made possible by accelerating developments in diamond-anvil cell methods coupled with new synchrotron radiation techniques. Significant advances have occurred in x-ray diffraction, spectroscopy, inelastic scattering, radiography, and infrared spectroscopy. With recent developments, structure refinements based on polycrystalline data up to multimegabar pressures have been possible. Single-crystal methods have been extended to megabar pressure, with the prospect of full crystallographic refinements. `Three- dimensional' diffraction data can be collected for determining strength, deformation, and elastic tensors at high P-T conditions. Studies carried out during the past three years provide numerous breakthroughs in high-pressure x-ray spectroscopy and a broad range of inelastic scattering methods. Other experiments have exploited the use of x-ray radiography over a range of pressures. Finally, synchrotron infrared measurements have revealed a wealth of high-pressure phenomena, particularly for molecular systems. Examples to be discussed include investigations of dense hydrogen; transformations in molecular materials; novel ceramics; new types of superconductors, electronic, and magnetic materials; and liquids and amorphous materials.

  5. Nuclear power plant Olkiluoto 3. Containment leakage test under extreme conditions

    Energy Technology Data Exchange (ETDEWEB)

    Fleckenstein, Tobias [TUEV SUED Industrie Service GmbH, Munich (Germany). Measaruement Technology Dept.

    2015-01-15

    Modern nuclear power plants place high demands on the design and execution of safety checks. TUEV SUED supported the containment leakage test for the largest- capacity third generation nuclear power plant in the world - Olkiluoto 3 in Finland. The experts successfully met the challenges presented by exceptional parameters of the project. The containment of Olkiluoto 3 is unique in that the vessel's volume is 80,000 m{sup 3} while measurements were carried out over a period of ten days. To execute the test, 75 temperature and 15 humidity sensors had to be installed and correctly interlinked by more than ten kilometres of cable. These instruments also needed to withstand an absolute pressure of 6 bar, ambient temperatures of 30 C and high levels of humidity. These conditions required comprehensive preparation and a high amount of qualification tests. Parts of the qualifications were carried out at the autoclave system of the Technical University in Munich, Germany, where the project test conditions could be simulated. The software required to determine the tests was developed by TUEV SUED and verified by German's national accreditation body DAkkS under ISO 17025. TUEV SUED enabled the test schedule to continue without delay by analysing all recorded data continuously on site, including pressure, temperature, humidity and leakage mass flow curves. With the comprehensive preparation, data acquisition system recording measurements continuously and the on-time result calculation, all components of the leak-tightness assessment were successfully completed in accordance with requirements.

  6. Sputtering at Mars: MAVEN observations of precipitating and escaping oxygen during nominal and extreme conditions

    Science.gov (United States)

    Curry, Shannon; Luhmann, Janet; Dong, Chuanfei; Ma, Yingjuan; Leblanc, Francois; Modolo, Ronan; Brain, David; Gruesbeck, Jacob; Hara, Takuya; Halekas, Jasper; Dong, Yaxue; Williamson, Hayley N.; Johnson, Robert E.; McFadden, James; Espley, Jared R.; Mitchell, David; Connerney, Jack; Eparvier, Frank; Lillis, Robert J.; Jakosky, Bruce

    2016-10-01

    Sputtering is believed to be one of the dominant escape mechanisms during the early epochs of our solar system when the solar activity and EUV intensities were much higher than the present day. Mars lacks a global dynamo magnetic field, which creates a scenario where the solar wind directly interacts with the upper atmosphere and newly created ions can be picked up and swept away by the background convection electric field. These pick-up ions can directly escape or precipitate back into the atmosphere and induce atmospheric sputtering of neutrals.The MAVEN spacecraft has observed the Mars upper atmosphere, ionosphere, magnetic topology and interactions with the Sun and solar wind during numerous Interplanetary Coronal Mass Ejection (ICME) impacts spanning from March 2015 to June 2016. ICMEs are associated with enhanced solar wind velocities, densities and magnetic field strength, and often drive heavy ion precipitation at much higher rates than during nominal conditions. Thus, ICMEs provide a unique environment for observing sputtering. We will compare MAVEN observations of heavy ion precipitation during nominal conditions as well as during ICMEs. Additionally, we will present global MHD and test particle simulations of the ICMEs in order to calculate sputtering escape rates for oxygen. Finally, we will use the observed and modeled sputtering escape rates to provide an initial estimate of the total sputtered atmospheric escape from Mars over billions of years.

  7. Modulation of Pleurodeles waltl DNA polymerase mu expression by extreme conditions encountered during spaceflight.

    Directory of Open Access Journals (Sweden)

    Véronique Schenten

    Full Text Available DNA polymerase µ is involved in DNA repair, V(DJ recombination and likely somatic hypermutation of immunoglobulin genes. Our previous studies demonstrated that spaceflight conditions affect immunoglobulin gene expression and somatic hypermutation frequency. Consequently, we questioned whether Polμ expression could also be affected. To address this question, we characterized Polμ of the Iberian ribbed newt Pleurodeles waltl and exposed embryos of that species to spaceflight conditions or to environmental modifications corresponding to those encountered in the International Space Station. We noted a robust expression of Polμ mRNA during early ontogenesis and in the testis, suggesting that Polμ is involved in genomic stability. Full-length Polμ transcripts are 8-9 times more abundant in P. waltl than in humans and mice, thereby providing an explanation for the somatic hypermutation predilection of G and C bases in amphibians. Polμ transcription decreases after 10 days of development in space and radiation seem primarily involved in this down-regulation. However, space radiation, alone or in combination with a perturbation of the circadian rhythm, did not affect Polμ protein levels and did not induce protein oxidation, showing the limited impact of radiation encountered during a 10-day stay in the International Space Station.

  8. Biological Membranes in Extreme Conditions: Simulations of Anionic Archaeal Tetraether Lipid Membranes.

    Directory of Open Access Journals (Sweden)

    Luis Felipe Pineda De Castro

    Full Text Available In contrast to the majority of organisms that have cells bound by di-ester phospholipids, archaeal membranes consist of di- and tetraether phospholipids. Originating from organisms that withstand harsh conditions (e.g., low pH and a wide range of temperatures such membranes have physical properties that make them attractive materials for biological research and biotechnological applications. We developed force-field parameters based on the widely used Generalized Amber Force Field (GAFF to enable the study of anionic tetraether membranes of the model archaean Sulfolobus acidocaldarius by computer simulations. The simulations reveal that the physical properties of these unique membranes depend on the number of cyclopentane rings included in each lipid unit, and on the size of cations that are used to ensure charge neutrality. This suggests that the biophysical properties of Sulfolobus acidocaldarius cells depend not only on the compositions of their membranes but also on the media in which they grow.

  9. Biological Membranes in Extreme Conditions: Simulations of Anionic Archaeal Tetraether Lipid Membranes

    Science.gov (United States)

    Pineda De Castro, Luis Felipe; Dopson, Mark

    2016-01-01

    In contrast to the majority of organisms that have cells bound by di-ester phospholipids, archaeal membranes consist of di- and tetraether phospholipids. Originating from organisms that withstand harsh conditions (e.g., low pH and a wide range of temperatures) such membranes have physical properties that make them attractive materials for biological research and biotechnological applications. We developed force-field parameters based on the widely used Generalized Amber Force Field (GAFF) to enable the study of anionic tetraether membranes of the model archaean Sulfolobus acidocaldarius by computer simulations. The simulations reveal that the physical properties of these unique membranes depend on the number of cyclopentane rings included in each lipid unit, and on the size of cations that are used to ensure charge neutrality. This suggests that the biophysical properties of Sulfolobus acidocaldarius cells depend not only on the compositions of their membranes but also on the media in which they grow. PMID:27167213

  10. Seasonal variations in microbial populations and environmental conditions in an extreme acid mine drainage environment.

    Science.gov (United States)

    Edwards, K J; Gihring, T M; Banfield, J F

    1999-08-01

    Microbial populations, their distributions, and their aquatic environments were studied over a year (1997) at an acid mine drainage (AMD) site at Iron Mountain, Calif. Populations were quantified by fluorescence in situ hybridizations with group-specific probes. Probes were used for the domains Eucarya, Bacteria, and Archaea and the two species most widely studied and implicated for their role in AMD production, Thiobacillus ferrooxidans and Leptospirillum ferrooxidans. Results show that microbial populations, in relative proportions and absolute numbers, vary spatially and seasonally and correlate with geochemical and physical conditions (pH, temperature, conductivity, and rainfall). Bacterial populations were in the highest proportion (>95%) in January. Conversely, archaeal populations were in the highest proportion in July and September ( approximately 50%) and were virtually absent in the winter. Bacterial and archaeal populations correlated with conductivity and rainfall. High concentrations of dissolved solids, as reflected by high conductivity values (up to 125 mS/cm), occurred in the summer and correlated with high archaeal populations and proportionally lower bacterial populations. Eukaryotes were not detected in January, when total microbial cell numbers were lowest (numbers of prokaryotes (10(8) to 10(9) cells/ml). T. ferrooxidans was in highest abundance (>30%) at moderate pHs and temperatures ( approximately 2.5 and 20 degrees C) in sites that were peripheral to primary acid-generating sites and lowest (0 to 5%) at low-pH sites (pH approximately 0.5) that were in contact with the ore body. L. ferrooxidans was more widely distributed with respect to geochemical conditions (pH = 0 to 3; 20 to 50 degrees C) but was more abundant at higher temperatures and lower pHs ( approximately 40 degrees C; pH approximately 0.5) than T. ferrooxidans.

  11. Optimizing spray drying conditions of sour cherry juice based on physicochemical properties, using response surface methodology (RSM).

    Science.gov (United States)

    Moghaddam, Arasb Dabbagh; Pero, Milad; Askari, Gholam Reza

    2017-01-01

    In this study, the effects of main spray drying conditions such as inlet air temperature (100-140 °C), maltodextrin concentration (MDC: 30-60%), and aspiration rate (AR) (30-50%) on the physicochemical properties of sour cherry powder such as moisture content (MC), hygroscopicity, water solubility index (WSI), and bulk density were investigated. This investigation was carried out by employing response surface methodology and the process conditions were optimized by using this technique. The MC of the powder was negatively related to the linear effect of the MDC and inlet air temperature (IT) and directly related to the AR. Hygroscopicity of the powder was significantly influenced by the MDC. By increasing MDC in the juice, the hygroscopicity of the powder was decreased. MDC and inlet temperature had a positive effect, but the AR had a negative effect on the WSI of powder. MDC and inlet temperature negatively affected the bulk density of powder. By increasing these two variables, the bulk density of powder was decreased. The optimization procedure revealed that the following conditions resulted in a powder with the maximum solubility and minimum hygroscopicity: MDC = 60%, IT = 134 °C, and AR = 30% with a desirability of 0.875.

  12. Physiological Responses to Microclimate Cooling Used By the Air Soldier Dressed at MOPP 4 in an Extreme Desert Condition: Effects of Six Configurations

    Science.gov (United States)

    2012-12-01

    4. Durnin, JVGA and J Womersley. Body fat assessed from total body density and its estimation from skinfold thickness : measurements on 481 men and... TABLE OF CONTENTS SECTION PAGE DISCLAIMER STATEMENTS... Table 1. All tests were performed in a simulated extreme desert environment (51.7°C dry bulb (Tdb), 16.6°C dew point (Tdp) (14% rh), 1.3 m∙sec-1

  13. Embedded optical probes for simultaneous pressure and temperature measurement of materials in extreme conditions

    Science.gov (United States)

    Sandberg, R. L.; Rodriguez, G.; Gibson, L. L.; Dattelbaum, D. M.; Stevens, G. D.; Grover, M.; Lalone, B. M.; Udd, E.

    2014-05-01

    We present recent efforts at Los Alamos National Laboratory (LANL) to develop sensors for simultaneous, in situ pressure and temperature measurements under dynamic conditions by using an all-optical fiber-based approach. While similar tests have been done previously in deflagration-to-detonation tests (DDT), where pressure and temperature were measured to 82 kbar and 400°C simultaneously, here we demonstrate the use of embedded fiber grating sensors to obtain high temporal resolution, in situ pressure measurements in inert materials. We present two experimental demonstrations of pressure measurements: (1) under precise shock loading from a gas-gun driven plate impact and (2) under high explosive driven shock in a water filled vessel. The system capitalizes on existing telecom components and fast transient digitizing recording technology. It operates as a relatively inexpensive embedded probe (single-mode 1550 nm fiber-based Bragg grating) that provides a continuous fast pressure record during shock and/or detonation. By applying well-controlled shock wave pressure profiles to these inert materials, we study the dynamic pressure response of embedded fiber Bragg gratings to extract pressure amplitude of the shock wave and compare our results with particle velocity wave profiles measured simultaneously.

  14. Energy efficiency and renewable energy under extreme conditions: Case studies from Antarctica

    Energy Technology Data Exchange (ETDEWEB)

    Tin, Tina [Antarctic and Southern Ocean Coalition, BP 80358, 45163 Olivet, CEDEX 3 (France); Sovacool, Benjamin K. [National University of Singapore (Singapore); Blake, David [British Antarctic Survey (United Kingdom); Magill, Peter [Australian Antarctic Division (Australia); El Naggar, Saad [Alfred Wegener Institute (Germany); Lidstrom, Sven [Swedish Polar Research Secretariat (Sweden); Ishizawa, Kenji [National Institute of Polar Research (Japan); Berte, Johan [International Polar Foundation (Belgium)

    2010-08-15

    This article showcases a range of small and large scale energy efficiency and renewable energy deployments at Antarctic research stations and field camps. Due to the cold and harsh environment, significant amounts of fuel are needed to support humans working and living in Antarctica. The purchase, transportation and storage of large amounts of fossil fuel entail significant economic costs and environmental risks and have motivated developments in energy efficiency and renewable energy deployment. Over the past three decades, improved building design, behavioral change, cogeneration, solar collectors, solar panels and wind turbines have been found to be effective in Antarctica, demonstrating that harsh environmental conditions and technological barriers do not have to limit the deployment of energy efficiency and renewable energy. The ambition to run entire stations or field camps on 100% renewable energy is increasingly common and feasible. While the power requirements of Antarctic research stations are small compared to urban installations on other continents, these case studies clearly demonstrate that if energy efficiency and renewable energy can be deployed widely on the coldest, darkest and most remote continent of the world, their deployment should be more widespread and encouraged on other continents. (author)

  15. Domain wall network as QCD vacuum and the chromomagnetic trap formation under extreme conditions

    Energy Technology Data Exchange (ETDEWEB)

    Nedelko, Sergei N.; Voronin, Vladimir E. [JINR, Bogoliubov Laboratory of Theoretical Physics, Dubna (Russian Federation)

    2015-04-01

    The ensemble of Euclidean gluon field configurations represented by the domain wall network is considered. A single domain wall is given by the sine-Gordon kink for the angle between chromomagnetic and chromoelectric components of the gauge field. The domain wall separates the regions with Abelian self-dual and anti-self-dual fields. The network of the domain wall defects is introduced as a combination of multiplicative and additive superpositions of kinks. The character of the spectrum and eigenmodes of color-charged fluctuations in the presence of the domain wall network is discussed. Conditions for the formation of a stable thick domain wall junction (the chromomagnetic trap) during heavy-ion collisions are discussed, and the spectrum of color-charged quasi-particles inside the trap is evaluated. An important observation is the existence of the critical size L{sub c} of a single trap stable against gluon tachyonic modes. The size L{sub c} is related to the value of gluon condensate left angle g{sup 2} F{sup 2} right angle. The growth of large lumps of merged chromomagnetic traps and the concept of the confinement-deconfinement transition in terms of the ensemble of domain wall networks are outlined. (orig.)

  16. Anaerobic digestion of the microalga Spirulina at extreme alkaline conditions: biogas production, metagenome, and metatranscriptome

    Science.gov (United States)

    Nolla-Ardèvol, Vímac; Strous, Marc; Tegetmeyer, Halina E.

    2015-01-01

    A haloalkaline anaerobic microbial community obtained from soda lake sediments was used to inoculate anaerobic reactors for the production of methane rich biogas. The microalga Spirulina was successfully digested by the haloalkaline microbial consortium at alkaline conditions (pH 10, 2.0 M Na+). Continuous biogas production was observed and the obtained biogas was rich in methane, up to 96%. Alkaline medium acted as a CO2 scrubber which resulted in low amounts of CO2 and no traces of H2S in the produced biogas. A hydraulic retention time (HRT) of 15 days and 0.25 g Spirulina L−1 day−1 organic loading rate (OLR) were identified as the optimal operational parameters. Metagenomic and metatranscriptomic analysis showed that the hydrolysis of the supplied substrate was mainly carried out by Bacteroidetes of the “ML635J-40 aquatic group” while the hydrogenotrophic pathway was the main producer of methane in a methanogenic community dominated by Methanocalculus. PMID:26157422

  17. First-Principles Investigations on Thermal Conductivity and Average Ionization of CH Ablators Under Extreme Conditions

    Science.gov (United States)

    Hu, S. X.; Goncharov, V. N.; McCrory, R. L.; Skupsky, S.; Collins, L. A.; Kress, J. D.

    2015-11-01

    A plastic CH ablator (polystyrene) is often used for inertial confinement fusion (ICF) target designs. Upon intense laser or x-ray ablations, a CH ablator can be shocked to warm-dense-matter (WDM) conditions. Many-body coupling and quantum electron degeneracy are expected to play an essential role in determining the properties of such warm dense plasmas. Using ab initio methods of quantum molecular dynamics (QMD), we have performed investigations on the principal Hugoniot of a CH ablator, the first-principles equation-of-state table of CH, and its effect on ICF simulations. In this presentation, we focus on the thermal conductivity and average ionization of CH-ablators under a wide range of plasma temperatures and densities. The resulting thermal conductivity (κ) and average ionization () show large differences from the usual model predictions in the WDM regime. These results, being fitted with analytical functions of plasma density and temperature, have been incorporated into radiation -hydrodynamics codes. Their effects on the ICF implosion simulations will be presented. This material is based upon work supported by the Department of Energy National Nuclear Security Administration under Award Number DE-NA0001944 and the Scientific Campaign 10 at LANL under Contract No. DE-AC52-06NA25396.

  18. Spirituality and Aging in Place: The Impact of Extreme Climatic Conditions on Domestic Gardening Practice.

    Science.gov (United States)

    Adams, Joanne; Pascal, Jan; Dickson-Swift, Virginia

    2014-12-01

    There is limited research exploring how domestic water restrictions imposed as a result of drought conditions impact upon the lives of independently living older people. Within this age group (60 years plus), the domestic garden frequently forms an intrinsic component of ongoing health and well-being. Gardening practice offers components of both mental and physical activity and, for many older people, leads to emotional and spiritual connection on a number of levels. The capacity of older people to maintain a garden during a period of water restrictions is greatly reduced, and the resulting impact on health and well-being is considerable. A recent study, conducted in south-eastern Australia, aimed to determine the benefits to health and well-being of maintaining a domestic garden for older people and the impact of water restrictions on garden practice. This occurred at a time following a prolonged period of drought and, in central Victoria, a complete ban on outside watering. In-depth qualitative interviews were conducted with 10 gardeners aged between 60 and 83 who had tended their garden over an extended period. The lived experience of gardening was explored through hermeneutic phenomenological analysis. Clear benefits to health and well-being were established, and yet, the essence of this experience lay in the capacity of gardeners to remain connected to their garden despite change. The crisis imposed by ongoing drought and restricted use of water generated a strong impetus for adaptation, resilience and acceptance of change. The spiritual nature of gardening practice clearly emerged and appeared to intensify the experience of gardening and consolidate adaption to change on a number of levels.

  19. Men in extreme conditions: some medical and psychological aspects of the Auschwitz concentration camp.

    Science.gov (United States)

    Radil-Weiss, T

    1983-08-01

    The second world war ended many years ago. Most of those who survived the stay at the German concentration camp at Auschwitz have already died of the consequences of their imprisonment; those still alive are already in the last third of their life. Is there any point in returning to the experiences of those days? Consideration of the mental hygiene of former prisoners cautions us that perhaps we should not do it. But consideration of the general interest holds that we are not entitled to ignore any knowledge that can contribute to social development--including medicine and psychology--even if acquired under unspeakably awful conditions. In addition, since the war new generations have grown up that play an increasingly significant role in various spheres of life but have little concrete information about those events; they can neither rationally nor emotionally understand how the horrors connected with fascism and the war could have happened. In a sense it is encouraging that they cannot grasp such inhuman behavior; nevertheless, we must adhere to the following motto: "Nothing must be forgotten, nobody will be forgotten." We owe it to those millions who did not survive--both the victims of the Holocaust and those who fought against it. These are arguments in favor of returning to the facts that are ineffaceably recorded somewhere in our memories. In doing so, however, we must remember that at times we are revisiting experiences of a boy of 14 as recalled by a 50-year-old man. The material below, examining the medical as well as psychological aspects of imprisonment at Auschwitz, is based on my own memories, as an adolescent imprisoned at Auschwitz. I have tried to move from this individual account to more general statements, although the methodological apparatus on which scientific analysis is usually based is absent.

  20. The family as a determinant of stunting in children living in conditions of extreme poverty: a case-control study

    Science.gov (United States)

    Reyes, Hortensia; Pérez-Cuevas, Ricardo; Sandoval, Araceli; Castillo, Raúl; Santos, José Ignacio; Doubova, Svetlana V; Gutiérrez, Gonzalo

    2004-01-01

    Background Malnutrition in children can be a consequence of unfavourable socioeconomic conditions. However, some families maintain adequate nutritional status in their children despite living in poverty. The aim of this study was to ascertain whether family-related factors are determinants of stunting in young Mexican children living in extreme poverty, and whether these factors differ between rural or urban contexts. Methods A case-control study was conducted in one rural and one urban extreme poverty level areas in Mexico. Cases comprised stunted children aged between 6 and 23 months. Controls were well-nourished children. Independent variables were defined in five dimensions: family characteristics; family income; household allocation of resources and family organisation; social networks; and child health care. Information was collected from 108 cases and 139 controls in the rural area and from 198 cases and 211 controls in the urban area. Statistical analysis was carried out separately for each area; unconditional multiple logistic regression analyses were performed to obtain the best explanatory model for stunting. Results In the rural area, a greater risk of stunting was associated with father's occupation as farmer and the presence of family networks for child care. The greatest protective effect was found in children cared for exclusively by their mothers. In the urban area, risk factors for stunting were father with unstable job, presence of small social networks, low rate of attendance to the Well Child Program activities, breast-feeding longer than six months, and two variables within the family characteristics dimension (longer duration of parents' union and migration from rural to urban area). Conclusions This study suggests the influence of the family on the nutritional status of children under two years of age living in extreme poverty areas. Factors associated with stunting were different in rural and urban communities. Therefore, developing and

  1. West Africa Extreme Rainfall Events and Large-Scale Ocean Surface and Atmospheric Conditions in the Tropical Atlantic

    Directory of Open Access Journals (Sweden)

    S. Ta

    2016-01-01

    Full Text Available Based on daily precipitation from the Global Precipitation Climatology Project (GPCP data during April–October of the 1997–2014 period, the daily extreme rainfall trends and variability over West Africa are characterized using 90th-percentile threshold at each grid point. The contribution of the extreme rainfall amount reaches ~50–90% in the northern region while it is ~30–50% in the south. The yearly cumulated extreme rainfall amount indicates significant and negative trends in the 6°N–12°N; 6°N–12°N; 17°W–10°W and 4°N–7°N; 4°N–7°N; 6°E–10°E 4°N–7°N; 6°E–10°E 4°N–7°N; 6°E–10°E domains, while the number of days exhibits nonsignificant trends over West Africa. The empirical orthogonal functions performed on the standardized anomalies show four variability modes that include all West Africa with a focus on the Sahelian region, the eastern region including the south of Nigeria, the western part including Guinea, Sierra Leone, Liberia, and Guinea-Bissau, and finally a small region at the coast of Ghana and Togo. These four modes are influenced differently by the large-scale ocean surface and atmospheric conditions in the tropical Atlantic. The results are applicable in planning the risks associated with these climate hazards, particularly on water resource management and civil defense.

  2. The family as a determinant of stunting in children living in conditions of extreme poverty: a case-control study

    Directory of Open Access Journals (Sweden)

    Doubova Svetlana V

    2004-11-01

    Full Text Available Abstract Background Malnutrition in children can be a consequence of unfavourable socioeconomic conditions. However, some families maintain adequate nutritional status in their children despite living in poverty. The aim of this study was to ascertain whether family-related factors are determinants of stunting in young Mexican children living in extreme poverty, and whether these factors differ between rural or urban contexts. Methods A case-control study was conducted in one rural and one urban extreme poverty level areas in Mexico. Cases comprised stunted children aged between 6 and 23 months. Controls were well-nourished children. Independent variables were defined in five dimensions: family characteristics; family income; household allocation of resources and family organisation; social networks; and child health care. Information was collected from 108 cases and 139 controls in the rural area and from 198 cases and 211 controls in the urban area. Statistical analysis was carried out separately for each area; unconditional multiple logistic regression analyses were performed to obtain the best explanatory model for stunting. Results In the rural area, a greater risk of stunting was associated with father's occupation as farmer and the presence of family networks for child care. The greatest protective effect was found in children cared for exclusively by their mothers. In the urban area, risk factors for stunting were father with unstable job, presence of small social networks, low rate of attendance to the Well Child Program activities, breast-feeding longer than six months, and two variables within the family characteristics dimension (longer duration of parents' union and migration from rural to urban area. Conclusions This study suggests the influence of the family on the nutritional status of children under two years of age living in extreme poverty areas. Factors associated with stunting were different in rural and urban communities

  3. Syntrophic associations from hypersaline soda lakes converting organic acids and alcohols to methane at extremely haloalkaline conditions.

    Science.gov (United States)

    Sorokin, Dimitry Y; Abbas, Ben; Geleijnse, Mitchell; Kolganova, Tatjana V; Kleerebezem, Robbert; van Loosdrecht, Mark C M

    2016-09-01

    Until now anaerobic oxidation of VFA at high salt-pH has been demonstrated only at sulfate-reducing conditions. Here, we present results of a microbiological investigation of anaerobic conversion of organic acids and alcohols at methanogenic conditions by syntrophic associations enriched from hypersaline soda lakes in Central Asia. Sediment incubation experiments showed active, albeit very slow, methane formation from acetate, propionate, butyrate and C2 C4 alcohols at pH 10 and various levels of salinity. Enrichments of syntrophic associations using hydrogenotrophic members of the genus Methanocalculus from soda lakes as partners resulted in several highly enriched cultures converting acetate, propionate, butyrate, benzoate and EtOH to methane. Most syntrophs belonged to Firmicutes, while the propionate-oxidizer formed a novel lineage within the family Syntrophobacteraceae in the Deltaproteobacteria. The acetate-oxidizing syntroph was identified as 'Ca. Syntrophonatronum acetioxidans' previously found to oxidize acetate at sulfate-reducing conditions up to salt-saturating concentrations. Butyrate and a benzoate-degrading syntrophs represent novel genus-level lineages in Syntrophomonadales which are proposed as Candidatus taxons 'Syntrophobaca', 'Syntrophocurvum' and 'Syntropholuna'. Overall, despite very slow growth, the results indicated the presence of a functionally competent syntrophic community in hypersaline soda lakes, capable of efficient oxidation of fermentation products to methane at extremely haloalkaline conditions.

  4. Morphological variations of wild populations of Nile tilapia (Oreochromis niloticus) living in extreme environmental conditions in the Kenyan Rift-Valley

    OpenAIRE

    Ndiwa, T.C.; Nyingi, D. W.; Claude, J.; Agnèse, Jean-François

    2016-01-01

    In this study, we use geometric morphometric method to establish morphological differences between natural populations of Nile tilapia from two extreme environmental conditions (high temperature and salinity) in Kenya, and compare them to two populations from regions experiencing less extreme conditions. To determine genetic influence on morphology, we correlated genetic data with morphological data. The study observed significant morphological differences between all studied populations, inc...

  5. Partial Root-Zone Drying of Olive (Olea europaea var. 'Chetoui') Induces Reduced Yield under Field Conditions.

    Science.gov (United States)

    Dbara, Soumaya; Haworth, Matthew; Emiliani, Giovani; Ben Mimoun, Mehdi; Gómez-Cadenas, Aurelio; Centritto, Mauro

    2016-01-01

    The productivity of olive trees in arid and semi-arid environments is closely linked to irrigation. It is necessary to improve the efficiency of irrigation techniques to optimise the amount of olive fruit produced in relation to the volume of water used. Partial root-zone drying (PRD) is a water saving irrigation technique that theoretically allows the production of a root-to-shoot signal that modifies the physiology of the above-ground parts of the plant; specifically reducing stomatal conductance (gs) and improving water use efficiency (WUE). Partial root-zone drying has been successfully applied under field conditions to woody and non-woody crops; yet the few previous trials with olive trees have produced contrasting results. Thirty year-old olive trees (Olea europaea 'var. Chetoui') in a Tunisian grove were exposed to four treatments from May to October for three-years: 'control' plants received 100% of the potential evapotranspirative demand (ETc) applied to the whole root-zone; 'PRD100' were supplied with an identical volume of water to the control plants alternated between halves of the root-zone every ten-days; 'PRD50' were given 50% of ETc to half of the root-system, and; 'rain-fed' plants received no supplementary irrigation. Allowing part of the root-zone to dry resulted in reduced vegetative growth and lower yield: PRD100 decreased yield by ~47% during productive years. During the less productive years of the alternate bearing cycle, irrigation had no effect on yield; this suggests that withholding of water during 'off-years' may enhance the effectiveness of irrigation over a two-year cycle. The amount and quality of oil within the olive fruit was unaffected by the irrigation treatment. Photosynthesis declined in the PRD50 and rain-fed trees due to greater diffusive limitations and reduced biochemical uptake of CO2. Stomatal conductance and the foliar concentration of abscisic acid (ABA) were not altered by PRD100 irrigation, which may indicate the

  6. Partial Root-Zone Drying of Olive (Olea europaea var. 'Chetoui' Induces Reduced Yield under Field Conditions.

    Directory of Open Access Journals (Sweden)

    Soumaya Dbara

    Full Text Available The productivity of olive trees in arid and semi-arid environments is closely linked to irrigation. It is necessary to improve the efficiency of irrigation techniques to optimise the amount of olive fruit produced in relation to the volume of water used. Partial root-zone drying (PRD is a water saving irrigation technique that theoretically allows the production of a root-to-shoot signal that modifies the physiology of the above-ground parts of the plant; specifically reducing stomatal conductance (gs and improving water use efficiency (WUE. Partial root-zone drying has been successfully applied under field conditions to woody and non-woody crops; yet the few previous trials with olive trees have produced contrasting results. Thirty year-old olive trees (Olea europaea 'var. Chetoui' in a Tunisian grove were exposed to four treatments from May to October for three-years: 'control' plants received 100% of the potential evapotranspirative demand (ETc applied to the whole root-zone; 'PRD100' were supplied with an identical volume of water to the control plants alternated between halves of the root-zone every ten-days; 'PRD50' were given 50% of ETc to half of the root-system, and; 'rain-fed' plants received no supplementary irrigation. Allowing part of the root-zone to dry resulted in reduced vegetative growth and lower yield: PRD100 decreased yield by ~47% during productive years. During the less productive years of the alternate bearing cycle, irrigation had no effect on yield; this suggests that withholding of water during 'off-years' may enhance the effectiveness of irrigation over a two-year cycle. The amount and quality of oil within the olive fruit was unaffected by the irrigation treatment. Photosynthesis declined in the PRD50 and rain-fed trees due to greater diffusive limitations and reduced biochemical uptake of CO2. Stomatal conductance and the foliar concentration of abscisic acid (ABA were not altered by PRD100 irrigation, which may

  7. Kinetics of Materials at Extreme Conditions: Understanding the Time Dependent Approach to Equilibrium at MaRIE

    Energy Technology Data Exchange (ETDEWEB)

    Kraus, R. G. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Mcnabb, D. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Kumar, M. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Eggert, J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Borg, J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Cerreta, E. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Dattelbaum, D. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Fried, L. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Greeff, C. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Stolken, J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

    2017-04-21

    The National Nuclear Security Agency has recently recognized that a long-term need exists to establish a stronger scientific basis for the assessment and qualification of materials and manufacturing processes for the nuclear stockpile and other national security applications. These materials may have undergone substantial changes with age, or may represent new materials that are being introduced because of difficulties associated with reusing or recreating materials used in original stockpile components. Also, with advancements in manufacturing methods, the NNSA anticipates opportunities for an enhanced range of control over fabricated components, an enhanced pace of materials development, and enhanced functionality. The development of qualification standards for these new materials will require the ability to understand and control material characteristics that affect both mechanical and dynamic performance. A unique aspect for NNSA is that the performance requirements for materials are often set by system hydrodynamics, and these materials must perform in extreme environments and loading conditions. Thus, the scientific motivation is to understand “Matter-Radiation Interactions in Extremes (MaRIE).”

  8. Geomicrobiological processes in extreme environments: A review

    Institute of Scientific and Technical Information of China (English)

    Hailiang Dong; Bingsong Yu

    2007-01-01

    @@ The last decade has seen an extraordinary growth of Geomicrobiology. Microorganisms have been studied in numerous extreme environments on Earth, ranging from crystalline rocks from the deep subsurface, ancient sedimentary rocks and hypersaline lakes, to dry deserts and deep-ocean hydrothermal vent systems. In light of this recent progress, we review several currently active research frontiers: deep continental subsurface microbiology, microbial ecology in saline lakes, microbial formation of dolomite, geomicrobiology in dry deserts,fossil DNA and its use in recovery of paleoenvironmental conditions, and geomicrobiology of oceans.Throughout this article we emphasize geomicrobiological processes in these extreme environments.

  9. Atmospheric CO2 concentration impacts on maize yield performance under dry conditions: do crop model simulate it right ?

    Science.gov (United States)

    Durand, Jean-Louis; Delusca, Kénel; Boote, Ken; Lizaso, Jon; Manderscheid, Remy; Jochaim Weigel, Hans; Ruane, Alex C.; Rosenzweig, Cynthia; Jones, Jim; Ahuja, Laj; Anapalli, Saseendran; Basso, Bruno; Baron, Christian; Bertuzzi, Patrick; Biernath, Christian; Deryng, Delphine; Ewert, Frank; Gaiser, Thomas; Gayler, Sebastian; Heinlein, Florian; Kersebaum, Kurt Christian; Kim, Soo-Hyung; Müller, Christoph; Nendel, Claas; Olioso, Albert; Priesack, Eckhart; Ramirez-Villegas, Julian; Ripoche, Dominique; Rötter, Reimund; Seidel, Sabine; Srivastava, Amit; Tao, Fulu; Timlin, Dennis; Twine, Tracy; Wang, Enli; Webber, Heidi; Zhao, Shigan

    2017-04-01

    In most regions of the world, maize yields are at risk of be reduced due to rising temperatures and reduced water availability. Rising temperature tends to reduce the length of the growth cycle and the amount of intercepted solar energy. Water deficits reduce the leaf area expansion, photosynthesis and sometimes, with an even more pronounced impact, severely reduce the efficiency of kernel set. In maize, the major consequence of atmospheric CO2 concentration ([CO2]) is the stomatal closure-induced reduction of leaf transpiration rate, which tends to mitigate those negative impacts. Indeed FACE studies report significant positive responses to CO2 of maize yields (and other C4 crops) under dry conditions only. Given the projections by climatologists (typically doubling of [CO2] by the end of this century) projected impacts must take that climate variable into account. However, several studies show a large incertitude in estimating the impact of increasing [CO2] on maize remains using the main crop models. The aim of this work was to compare the simulations of different models using input data from a FACE experiment conducted in Braunschweig during 2 years under limiting and non-limiting water conditions. Twenty modelling groups using different maize models were given the same instructions and input data. Following calibration of cultivar parameters under non-limiting water conditions and under ambient [CO2] treatments of both years, simulations were undertaken for the other treatments: High [ CO2 ] (550 ppm) 2007 and 2008 in both irrigation regimes, and DRY AMBIENT 2007 and 2008. Only under severe water deficits did models simulate an increase in yield for CO2 enrichment, which was associated with higher harvest index and, for those models which simulated it, higher grain number. However, the CO2 enhancement under water deficit simulated by the 20 models was 20 % at most and 10 % on average only, i.e. twice less than observed in that experiment. As in the experiment

  10. Extreme storm surges in the south of Brazil: atmospheric conditions and shore erosion

    Directory of Open Access Journals (Sweden)

    Cláudia Klose Parise

    2009-09-01

    Full Text Available The region under study is regularly subject to the occurrence of storms associated with frontal systems and extratropical cyclones, since it is located near one of the cyclogenetic regions in South America. These storms can generate storm surges that cause anomalous high sea level rises on Cassino Beach. The use of reanalysis data along with an efficient technique for the location of the cyclone, using a vorticity threshold, has provided a new classification based upon the trajectories of events that produce positive sea level variation. Three patterns have been identified: 1 Cyclogenesis to the south of Argentina with displacement to the east and a trajectory between 47.5ºS and 57.5ºS; 2 Cyclogenesis to the south of Uruguay with displacement to the east and a trajectory between 35ºS and 42.5ºS; and 3 Cyclogenesis to the south of Uruguay with displacement to the southeast and a trajectory between 35ºS and 57.5ºS. Maximum water level elevation above the mean sea level and beach erosion were associated, respectively, with winter and summer storms. Cassino beach displayed a seasonal morphological behavior, with short periods of episodic erosion associated with winter storm events followed by long periods of accretion characterized by the dominance of fair weather conditions.Marés meteorológicas que geram sobre-elevações do nível do mar são freqüentes na costa do Rio Grande do Sul e respondem às variações ocorridas na atmosfera. Torna-se importante, dessa maneira, definir padrões meteorológicos sinóticos responsáveis por gerar eventos de marés meteorológicas intensas na Praia do Cassino como objetivo desse trabalho. O uso de dados de reanálise associados a uma técnica eficiente de localização do ciclone, aplicando o conceito de vorticidade, permitiu definir uma nova classificação com base na trajetória de ciclones extratropicais responsáveis pela subida do nível do mar. Três padrões de trajetórias foram

  11. Influence of primary crystallisation conditions on the mechanical and interfacial properties of micronised budesonide for dry powder inhalation.

    Science.gov (United States)

    Kubavat, Harshal A; Shur, Jagdeep; Ruecroft, Graham; Hipkiss, David; Price, Robert

    2012-07-01

    Investigate the influence of primary crystallisation conditions on the mechanical properties and secondary processing behaviour of budesonide for dry powder inhaler (DPI) formulations. Young's modulus of two batches of budesonide crystals (samples A and B) produced using different anti-solvents was determined using nanoindentation. Physicochemical and surface interfacial properties via the cohesive-adhesive balance (CAB) approach to colloid probe atomic force microscopy (AFM) of air-jet micronised budesonide crystals were also investigated. These data were correlated to in vitro aerosolization performance of carrier-based DPI formulations containing either budesonide samples A or B and lactose monohydrate. Young's modulus of budesonide samples A and B crystals was 0.95 and 4.04 GPa, respectively. Sample A crystals with low Young's modulus exhibited poorer micronisation efficiency than sample B. CAB analysis of micronised budesonide samples A and B, suggest that sample B budesonide had a greater adhesion to lactose than sample A. These data correlated with in vitro aerosolisation studies, which showed that the fine particle delivery of budesonide sample A was higher than that of sample B. In conclusion, crystallisation conditions may affect the mechanical properties of budesonide, and therefore secondary processing of the material and their interfacial properties and product performance in carrier based DPI formulations. Copyright © 2012 Elsevier B.V. All rights reserved.

  12. Cosmos caudatus as a potential source of polyphenolic compounds: optimisation of oven drying conditions and characterisation of its functional properties.

    Science.gov (United States)

    Mediani, Ahmed; Abas, Faridah; Khatib, Alfi; Tan, Chin Ping

    2013-08-29

    The aim of the study was to analyze the influence of oven thermal processing of Cosmos caudatus on the total polyphenolic content (TPC) and antioxidant capacity (DPPH) of two different solvent extracts (80% methanol, and 80% ethanol). Sonication was used to extract bioactive compounds from this herb. The results showed that the optimised conditions for the oven drying method for 80% methanol and 80% ethanol were 44.5 °C for 4 h with an IC₅₀ of 0.045 mg/mL and 43.12 °C for 4.05 h with an IC₅₀ of 0.055 mg/mL, respectively. The predicted values for TPC under the optimised conditions for 80% methanol and 80% ethanol were 16.5 and 15.8 mg GAE/100 g DW, respectively. The results obtained from this study demonstrate that Cosmos caudatus can be used as a potential source of antioxidants for food and medicinal applications.

  13. Exploring Mbar shock conditions and isochorically heated aluminum at the Matter in Extreme Conditions end station of the Linac Coherent Light Source (invited)

    Energy Technology Data Exchange (ETDEWEB)

    Fletcher, L. B. [SLAC National Accelerator Laboratory, 2575 Sand Hill Road, Menlo Park, California 94025 (United States); Physics Department, University of California Berkeley, Berkeley, California 94709 (United States); Lee, H. J.; Gauthier, M.; Galtier, E.; Nagler, B.; Heimann, P.; Hastings, J. B.; Glenzer, S. H. [SLAC National Accelerator Laboratory, 2575 Sand Hill Road, Menlo Park, California 94025 (United States); Barbrel, B.; Falcone, R. W. [Physics Department, University of California Berkeley, Berkeley, California 94709 (United States); Döppner, T.; LePape, S.; Ma, T.; Pak, A.; Turnbull, D. [Lawrence Livermore National Laboratory, P.O. Box 808, Livermore, California 94551 (United States); White, T.; Gregori, G. [Department of Physics, University of Oxford, Parks Road, Oxford OX1 3PU (United Kingdom); Wei, M. [General Atomics, San Diego, California 87544 (United States); Zastrau, U. [SLAC National Accelerator Laboratory, 2575 Sand Hill Road, Menlo Park, California 94025 (United States); Institute for Optics and Quantum Electronics, Friedrich-Schiller-University, 07743 Jena (Germany)

    2014-11-15

    Recent experiments performed at the Matter in Extreme Conditions end station of the Linac Coherent Light Source (LCLS) have demonstrated the first spectrally resolved measurements of plasmons from isochorically heated aluminum. The experiments have been performed using a seeded 8-keV x-ray laser beam as a pump and probe to both volumetrically heat and scatter x-rays from aluminum. Collective x-ray Thomson scattering spectra show a well-resolved plasmon feature that is down-shifted in energy by 19 eV. In addition, Mbar shock pressures from laser-compressed aluminum foils using velocity interferometer system for any reflector have been measured. The combination of experiments fully demonstrates the possibility to perform warm dense matter studies at the LCLS with unprecedented accuracy and precision.

  14. Desiccation and Mortality Dynamics in Seedlings of Different European Beech (Fagus sylvatica L.) Populations under Extreme Drought Conditions

    DEFF Research Database (Denmark)

    Bolte, Andreas; Czajkowski, Tomasz; Cocozza, Claudia

    2016-01-01

    , but not with the geographic margins of beech range. Thus, beech range marginality may be more due to climatic conditions than to geographic range. The outcome of this study suggests the genetic variation has a major influence on the varying adaptive potential of the investigated populations.......European beech (Fagus sylvatica L., hereafter beech), one of the major native tree species in Europe, is known to be drought sensitive. Thus, the identification of critical thresholds of drought impact intensity and duration are of high interest for assessing the adaptive potential of European...... beech to climate change in its native range. In a common garden experiment with one-year-old seedlings originating from central and marginal origins in six European countries (Denmark, Germany, France, Romania, Bosnia-Herzegovina, and Spain), we applied extreme drought stress and observed desiccation...

  15. Sensitivities of crop models to extreme weather conditions during flowering period demonstrated for maize and winter wheat in Austria

    DEFF Research Database (Denmark)

    Eitzinger, J; Thaler, S; Schmid, E;

    2013-01-01

    The objective of the present study was to compare the performance of seven different, widely applied crop models in predicting heat and drought stress effects. The study was part of a recent suite of model inter-comparisons initiated at European level and constitutes a component that has been...... lacking in the analysis of sources of uncertainties in crop models used to study the impacts of climate change. There was a specific focus on the sensitivity of models for winter wheat and maize to extreme weather conditions (heat and drought) during the short but critical period of 2 weeks after...... or minimum tillage. Since no comprehensive field experimental data sets were available, a relative comparison of simulated grain yields and soil moisture contents under defined weather scenarios with modified temperatures and precipitation was performed for a 2-week period after flowering. The results may...

  16. Analyses of crystal field and exchange interaction of Dy3Ga5O12 under extreme conditions

    Institute of Scientific and Technical Information of China (English)

    Wang Wei; Qi Xin; Yue Yuan

    2011-01-01

    This paper theoretically investigates the effects of crystal field and exchange interaction field on magnetic properties in dysprosium gallium garnet under extreme conditions (low temperatures and high magnetic fields) based on quantum theory. Here, five sets of crystal field parameters are discussed and compared. It demonstrates that, only considering the crystal field effect, the experiments can not be successfully explained. Thus, referring to the molecular field theory,an effective exchange field associated with the Dy-Dy exchange interaction is further taken into account. Under special consideration of crystal field and the exchange interaction field, it obtains an excellent agreement between the theoretical results and experiments, and further confirms that the exchange interaction field between rare-earth ions has great importance to magnetic properties in paramagnetic rare-earth gallium garnets.

  17. Tribological Behavior of TiAl Metal Matrix Composite Brake Disk with TiC Reinforcement Under Dry Sliding Conditions

    Science.gov (United States)

    Liaquat, Hassan; Shi, Xiaoliang; Yang, Kang; Huang, Yuchun; Liu, Xiyao; Wang, Zhihai

    2017-07-01

    In this investigation, the effect of TiC particulate reinforcement and sintering parameters on tribological behavior of TiAl metal matrix composite (TMMC) has been studied and compared with commercially conventional gray cast iron to evaluate the use of TMMC as brake disk material in an automobile. Three sample disks of TMMC containing TiC particulate reinforcement (D1-5 wt.%, D2 and D3-10 wt.%) were produced by the spark plasma sintering process. D3 compared with D2 was sintered at a higher temperature to evaluate the effect of SPS parameters on the wear characteristics of TMMC. All experiments were performed on pin-on-disk tribotester under a dry sliding condition with different loads (10-11.5 N) and sliding velocities (0.2-0.9 m/s). It is found that higher content of TiC increased TMMC hardness and density. XRD technique has been used to analyze the phase composition. Owing to the high sintering temperature, α-2 Ti3Al phase was formed which further enhanced the matrix anti-wear capability. Scanning electron microscope (SEM) was used to capture the wear track and observe wear mechanism. Energy-dispersive spectroscopy (EDS) has been used to analyze the tribofilm and wear debris. The results showed that the tribofilm for TMMC was mainly composed of metal oxides. Oxidation of Al and Ti due to frictional heat provides wear-resistant protective layer. Under almost all sliding conditions, TMMC, especially disk D3, exhibited minimum wear rate and stable friction coefficient, whereas gray cast iron exhibited lower and unstable friction coefficient as well as higher wear rate. TMMC has shown superior tribological characteristics over gray cast iron in terms of low wear rate along with stable and adequate friction coefficient which is necessary for braking operation and life of brake disk. However, further investigation on full-scale automobile conditions is needed for its practical application.

  18. Imaging Under Extreme Conditions

    Science.gov (United States)

    2015-07-28

    Science, Nature, JACS, JPC , ChemPhysChem, PNAS, Nano Lett., and Angewandte Chemie. The applications of 4D UEM (and diffraction) are numerous, and we...Caltech were reported in Science, Nature, JACS, JPC , ChemPhysChem, PNAS, Nano Lett., and Angewandte Chemie. The applications of 4D UEM (and diffraction

  19. Habitability in Extreme Conditions

    Science.gov (United States)

    de Lobkowicz, Ysaline; de Crombrugghe, Guerric; Le Maire, Victor; Jago, Alban; Denies, Jonathan; van Vynckt, Delphine; Reydams, Marc; Mertens, Alexandre

    A manned space mission could be perfectly prepared in terms of sciences and technologies, but without a good habitat, a place where the needs of the crew are respected, this isolation and confinement can turn into a nightmare. There is the limitation of engineering: it is more than important to take care about architecture, when human lives are part of the experiment. The goal of the research is the analysis of the hard life of isolation and confinement in Mars' hostile environment and how architecture is a way to improve it. The objective is to place the human in the middle of the analysis. What does a person really need? Therefore Maslow's idea, the pyramid of primary needs, gives us the hierarchy to follow: first survival, food and beverage, then sleep, and only then protection, social activities and work. [1] No more luxury. If all these aspects are respected, a human is able to survive, like it did since so many years. The idea is that each of these main activities has to be related to a different type of space, to provide variability in this close environment. For example, work and relaxing areas have to be separated; a human being needs time for himself, without concentration. A workspace and a relaxing area have a different typology, different colours and lighting, dimensions, furniture. This has also to be respected in a spacecraft. For this research, different sources are used, mainly in the psychological aspect, which is the most important. [2] Therefore questionnaires, interviews, diaries of past expeditions are full of treasures. We do not have to search too far: on earth; polar expeditions, submarines, military camps, etc., give a lot of information. Some very realistic simulations, as on the Mars Desert Research Station (MDRS), will also be used as material: a good analysis of the defaults and well-organized part of the station can conduct to important conclusions. [3] A found analysis and a well-designed habitat are considerable keys for the success of the mission. References: [1] A. Maslow (1943) Theory of Human Motivation [2] J. Stuster (1996) Bold Endeavors, Lessons from Polar and Space Exploration [3] Mars Society, Mars Desert Research Station in Utah

  20. Optimization of spray-drying conditions for the large-scale preparation of Bacillus thuringiensis var. israelensis after downstream processing.

    Science.gov (United States)

    Prabakaran, G; Hoti, S L

    2008-05-01

    Reduction of water activity in the formulations of mosquito biocontrol agent, Bacillus thuringiensis var. israelensis is very important for long term and successful storage. A protocol for spray drying of B. thuringiensis var. israelensis was developed through optimizing parameters such as inlet temperature and atomization type. A indigenous isolate of B. thuringiensis var. israelensis (VCRC B-17) was dried by freeze and spray drying methods and the moisture content and mosquito larvicidal activity of materials produced by the two methods were compared. The larvicidal activity was checked against early fourth instars Aedes aegypti larvae. Results showed that the freeze-dried powders retained the larvicidal activity fairly well. The spray-dried powder moderately lost its larvicidal activity at different inlet temperatures. Between the two types of atomization, centrifugal atomization retained more activity than the nozzle type atomization. Optimum inlet temperature for both centrifugal and nozzle atomization was 160 degrees C. Keeping the outlet temperature constant at 70 degrees C the moisture contents for the spray-dried powders through centrifugal atomization and freeze-dried powders were 10.23% and 11.80%, respectively. The LC(50) values for the spray-dried and freeze-dried powders were 17.42 and 16.18 ng/mL, respectively. Spore count of materials before drying was 3 x 10(10) cfu/mL and after spray drying through nozzle and centrifugal atomization at inlet and outlet temperature of 160 degrees C/70 degrees C were 2.6 x 10(9) and 5.0 x 10(9) cfu/mL, respectively.

  1. The Wear Behavior of HVOF Sprayed Near-Nanostructured WC-17%Ni(80/20)Cr Coatings in Dry and Slurry Wear Conditions

    Science.gov (United States)

    Ben Mahmud, Tarek A.; Atieh, Anas M.; Khan, Tahir I.

    2017-07-01

    The ability to deposit nanostructured feedstock by using high-velocity oxygen-fuel (HVOF) spray offers potential improvements in coating hardness, wear resistance and toughness for applications in the oil sands industry. In this study, the wear behavior of a near-nanostructured coating was compared under dry and slurry abrasive wear test using an uncoated AISI-1018 low-carbon steel substrate as a reference. The coating microstructures were analyzed in the as-sprayed, dry and slurry test conditions using scanning electron microscopy, x-ray diffraction and microhardness measurements. Wear behavior of the steel and coating surfaces were assessed using a pin-on-plate wear test under various loads. The results showed that a coating could be successfully deposited using the HVOF spraying technique and with retention of the near-nanosized WC dispersion within the coating structure. The wear rate under dry test conditions was greater for the steel and coating compared to tests performed under slurry conditions. Examination of the wear tracks revealed that the wear mechanism was different for the two test conditions. Wear in the dry test condition resulted from 2-body abrasion, while 3-body abrasion dominated wear in slurry conditions. The latter showed lower wear rates due to a lubricating effect of the oil.

  2. Extreme thermodynamic conditions: novel stoichiometries, violations of textbook chemistry, and intriguing possibilities for the synthesis of new materials

    Science.gov (United States)

    Stavrou, Elissaios

    As evidenced by numerous experimental and theoretical studies, application of high pressure can dramatically modify the atomic arrangement and electronic structures of both elements and compounds. However, the great majority of research has been focused on the effect of pressure on compounds with constant stoichiometries (typically those stable under ambient conditions). Recent theoretical predictions, using advanced search algorithms, suggest that composition is another important variable in the search for stable compounds, i.e. that the more stable stoichiometry at elevated pressures is not a priory the same as that at ambient pressure. Indeed, thermodynamically stable compounds with novel compositions were theoretically predicted and experimentally verified even in relatively simple chemical systems including: Na-Cl, C-N, Li-H, Na-H, Cs-N, H-N, Na-He, Xe-Fe. These materials are stable due to the formation of novel chemical bonds that are absent, or even forbidden, at ambient conditions. Tuning the composition of the system thus represents another important, but poorly explored approach to the synthesis of novel materials. By varying the stoichiometry one can design novel materials with enhanced properties (e.g. high energy density, hardness, superconductivity etc.), that are metastable at ambient conditions and synthesized at thermodynamic conditions less extreme than that those required for known stoichiometries. Moreover, current outstanding questions, ``anomalies'' and ``paradoxes'' in geo- and planetary science (e.g. the Xenon paradox) could be addressed based on the stability of surprising, stoichiometries that challenge our traditional ``textbook'' picture. In this talk, I will briefly present recent results and highlight the need of close synergy between experimental and theoretical efforts to understand the challenging and complex field of variable stoichiometry under pressure. Finally, possible new routes for the synthesis of novel materials will be

  3. Seed storage at elevated partial pressure of oxygen, a fast method for analysing seed ageing under dry conditions

    NARCIS (Netherlands)

    Groot, S.P.C.; Surki, A.A.; Vos, de R.C.H.; Kodde, J.

    2012-01-01

    Background and Aims Despite differences in physiology between dry and relative moist seeds, seed ageing tests most often use a temperature and seed moisture level that are higher than during dry storage used in commercial practice and gene banks. This study aimed to test whether seed ageing under

  4. The role of canopy hydrological diversity and complexity on water balance and carbon sequestration during dry conditions: a modeling study

    Science.gov (United States)

    Lin, L.; Stewart, A.; Band, L. E.

    2016-12-01

    The importance and influence of forest to catchment hydrology have been well recognized. In the South Eastern U.S., Chapel Hill, NC, evapotranspiration by forest dominates almost 80% of the annual precipitation in long term average. Stomatal conductivity varies by tree species and its response to dry condition differently between evergreen and deciduous, and within their phonology groups. In this study, we simulated the catchment hydrology and forest ecosystem at a local catchment, Cane Creek, in the Chapel Hill triangle area using a spatially distributed, process-based hydro-ecological model, RHESSys. We incorporated characteristics of individual tree species to represent high hydrological diversity (e.g., maple, oak, pine), which has been modeled as either evergreen or deciduous (low hydrological diversity) in many studies. With tree species specifically modeled, we were able to investigate the role of tree species diversity and complexity on catchment hydrology. Local forest plant diversity, size, and density were provided by the U.S. Forest Services FIA, and tree species physiological parameters were obtained through researches at Duke Forest. High hydrological diversity canopy has higher water use and carbon sequestration than low hydrological diversity canopy. This result supports the optimality theory that emergent vegetation pattern in landscape maximizes ecosystem productivity and water use efficiency. Previous study emphasized this emergent pattern in terms of vegetation density along the hillslope gradient, and we further emphasized the emergent pattern in terms of hydrological diversity in this study.

  5. Nafion-porous cerium oxide nanotubes composite membrane for polymer electrolyte fuel cells operated under dry conditions

    Science.gov (United States)

    Ketpang, Kriangsak; Oh, Kwangjin; Lim, Sung-Chul; Shanmugam, Sangaraju

    2016-10-01

    A composite membrane operated in polymer electrolyte fuel cells (PEFCs) under low relative humidity (RH) is developed by incorporating cerium oxide nanotubes (CeNT) into a perfluorosulfonic acid (Nafion®) membrane. Porous CeNT is synthesized by direct heating a precursor impregnated polymer fibers at 500 °C under an air atmosphere. Compared to recast Nafion and commercial Nafion (NRE-212) membranes, the Nafion-CeNT composite membrane generates 1.1 times higher power density at 0.6 V, operated at 80 °C under 100% RH. Compared to Nafion-cerium oxide nanoparticles (Nafion-CeNP) membrane, the Nafion-CeNT provides 1.2 and 1.7 times higher PEFC performance at 0.6 V when operated at 80 °C under 100% and 18% RH, respectively. Additionally, the Nafion-CeNT composite membrane exhibits a good fuel cell operation under 18% RH at 80 °C. Specifically, the fluoride emission rate of Nafion-CeNT composite membrane is 20 times lower than that of the commercial NRE-212 membrane when operated under 18% RH at 80 °C for 96 h. The outstanding PEFC performance and durability operated under dry conditions is mainly attributed to the facile water diffusion capability as well as the effective hydroxyl radical scavenging property of the CeNT filler, resulting in significantly mitigating both the ohmic resistance and Nafion membrane degradation.

  6. Efficacy of entomopathogenic fungi (Ascomycetes: Hypocreales) against adult Haematobia irritans (Diptera: Muscidae) under stable conditions in the Mexican dry tropics.

    Science.gov (United States)

    Galindo-Velasco, E; Lezama-Gutiérrez, R; Cruz-Vázquez, C; Pescador-Rubio, A; Angel-Sahagún, C A; Ojeda-Chi, M M; Rodríguez-Vivas, R I; Contreras-Lara, D

    2015-04-30

    The purpose of this paper is to evaluate the effect of five strains of Metarhizium anisopliae (Ma) and three strains of Isaria fumosorosea (Ifr) at a concentration of 1×10(8)colony-forming units/ml applied by spraying onto bovines with controlled infestation of Haematobia irritans under stable conditions in the Mexican dry tropics. Four experiments were performed, in each of which three treatments (two fungal strains and one control) were evaluated with eight repetitions for each one, by carrying out a single application of the aqueous suspension of each strain. The animals were isolated in individual cages and direct counts of the infestation were carried out for 13 days. It was observed that strains Ma2, Ma6, Ma10, Ma14, and Ma34 caused 94-100% reduction in infestation between days 12 and 13 post-treatment, while strains Ifr19, Ifr11, and Ifr12 reduced infestation from 90% to 98% up to day 13 post-application. There was an effect in the generation of horn flies from the excrement of bovines that were treated with different strains, reducing the reproduction of subsequent generations. It was concluded that the strains of M. anisopliae and I. fumosorosea evaluated in this study can be used as biocontrol agents in infestations of H. irritans in stabled bovines.

  7. Effect of Heat Treatment on the Abrasive Wear Behavior of High Chromium Iron under Dry Sliding Condition

    Directory of Open Access Journals (Sweden)

    A.A. Ayeni

    2012-06-01

    Full Text Available The effect of heat treatment on the abrasive wear behavior of high chromium cast iron (NF253AHT under dry sliding condition has been investigated. Rectangular cross sectioned samples of the alloy were produced by sand casting. After casting, the samples were machined to equal dimensions of 50 mm x 15 mm x 10 mm and heat treated by annealing, hardening and tempering. Abrasive wear tests were carried out on the samples using the pin-on-disc wear test. The tests were carried out under restricted values of speed, load and time. Within this limit, the hardened sample displayed a superior wear resistance, while the annealed sample displayed the weakest wear resistance. A graphical model (wear map displaying all the wear regimes of the alloy, which may serve as a wear predictive tool was subsequently developed from the results of the wear tests. With the exception of the as-cast and annealed specimen, all other specimens (hardened and tempered have functioned adequately in wear prone environment, but with different degree of effectiveness. Hence, the hardened and tempered samples can be used in shot blast equipments and in the grinding of minerals.

  8. Reaction of Basaltic Materials under High-Fidelity Venus Surface Conditions using the Glenn Extreme Environment Rig: First Results

    Science.gov (United States)

    Radoman-Shaw, Brandon; Harvey, Ralph; Costa, Gustavo; Nakley, Leah Michelle; Jacobson, Nathan S.

    2016-01-01

    Both historical and current investigations of Venus suggest that atmosphererock interactions play a critical role in the evolution of its atmosphere and crust. We have begun a series of systematic experiments designed to further our understanding of atmosphere-driven weathering and secondary mineralization of basaltic materials that may be occurring on Venus today. Our experiments expose representative igneous phases (mineral, glasses and rocks) to a high-fidelity simulation of Venus surface conditions using the NASA Glenn Extreme Environment Rig (GEER) located at the NASA Glenn Research Center in Cleveland, Ohio. GEER is a very large (800L) vessel capable of producing a long-term, high fidelity simulation of both the physical conditions (750 K and 92 bar) and atmospheric chemistry (down to the ppb-level) asso-ciated with the Venusian surface. As of this writing we have just finished the first of several planned experiments: a 42-day exposure of selected mineral, rocks and volcanic glasses. Our goal is to identify and prioritize the reactions taking place and better our understanding of their importance in Venus' climate history.

  9. The [CII]/[NII] far-infrared line ratio at z>5: extreme conditions for “normal” galaxies

    Science.gov (United States)

    Pavesi, Riccardo; Riechers, Dominik; Capak, Peter L.; Carilli, Chris Luke; Sharon, Chelsea E.; Stacey, Gordon J.; Karim, Alexander; Scoville, Nicholas; Smolcic, Vernesa

    2017-01-01

    Thanks to the Atacama Large (sub-)Millimeter Array (ALMA), observations of atomic far-infrared fine structure lines are a very productive way of measuring physical properties of the interstellar medium (ISM) in galaxies at high redshift, because they provide an unobscured view into the physical conditions of star formation. While the bright [CII] line has become a routine probe of the dynamical properties of the gas, its intensity needs to be compared to other lines in order to establish the physical origin of the emission. [NII] selectively traces the