WorldWideScience

Sample records for extraction tube molten

  1. Some aspects of the electrochemical formation of carbon micro-tubes from molten chlorides

    Directory of Open Access Journals (Sweden)

    Yaghmaee M.S.

    2003-01-01

    Full Text Available Carbon nano/micro-tubes have been successfully synthesized by an electrochemical way from the NaCl-KCl-5% MgCl2 molten salt on the surface of a graphite cathode. The length of the tubes is above 100 µm, while their diameter ranges from hundreds of nanometers to 1-2 µm. A new cleaning procedure of the carbon tubes from the remaining salt has been developed with acetone found to be the best cleaning agent. It has been shown that in addition to carbon micro-tubes, some tube-like or rod-like structures can be formed, which do not actually consist of carbon but of the remained salt.

  2. Optimal spacing within a tubed, volumetric, cavity receiver suitable for modular molten salt solar towers

    Science.gov (United States)

    Turner, Peter

    2016-05-01

    A 2-dimensional radiation analysis has been developed to analyse the radiative efficiency of an arrangement of heat transfer tubes distributed in layers but spaced apart to form a tubed, volumetric receiver. Such an arrangement could be suitable for incorporation into a cavity receiver. Much of the benefit of this volumetric approach is gained after using 5 layers although improvements do continue with further layers. The radiation analysis splits each tube into multiple segments in which each segment surface can absorb, reflect and radiate rays depending on its surface temperature. An iterative technique is used to calculate appropriate temperatures depending on the distribution of the net energy absorbed and assuming that the cool heat transfer fluid (molten salt) starts at the front layer and flows back through successive layers to the rear of the cavity. Modelling the finite diameter of each layer of tubes increases the ability of a layer to block radiation scattered at acute angles and this effect is shown to reduce radiation losses by nearly 25% compared to the earlier 1-d analysis. Optimum efficient designs tend to occur when the blockage factor is 0.2 plus the inverse of the number of tube layers. It is beneficial if the distance between successive layers is ≥ 2 times the diameter of individual tubes and in this situation, if the incoming radiation is spread over a range of angles, the performance is insensitive to the degree of any tube positional offset or stagger between layers.

  3. Lanthanides extraction processes in molten fluoride media. Application to nuclear spent fuel reprocessing

    OpenAIRE

    Taxil, Pierre; Massot, Laurent; Nourry, Christophe; Gibilaro, Mathieu; Chamelot, Pierre; Cassayre, Laurent

    2009-01-01

    This paper describes four techniques of extraction of lanthanides elements (Ln) from molten salts in the general frame of reprocessing nuclear wastes; One of them is chemical: the precipitation of Ln ions in insoluble compounds (oxides or oxifluorides); the others use electrochemical methodology in molten fluorides for extraction and measurement of the progress of the processes: first electrodeposition of pure Ln metals on an inert cathode material was proved to be incomplete and cause probl...

  4. Electrochemical extraction of samarium from molten chlorides in pyrochemical processes

    Energy Technology Data Exchange (ETDEWEB)

    Castrillejo, Y., E-mail: ycastril@qa.uva.es [QUIANE/Dept Quimica Analitica, F. de Ciencias, Universidad de Valladolid, Prado de la Magdalena s/n, 47005 Valladolid (Spain); Fernandez, P. [QUIANE/Dept Quimica Analitica, F. de Ciencias, Universidad de Valladolid, Prado de la Magdalena s/n, 47005 Valladolid (Spain); Medina, J. [Dept Fisica Materia Condensada Cristalografia y Mineralogia, F. de Ciencias, Universidad de Valladolid, Prado de la Magdalena s/n, 47005 Valladolid (Spain); Hernandez, P. [Centro de Investigaciones Quimicas, Universidad Autonoma del Estado de Hidalgo, Carr. Pachuca-Tulancingo Km. 4.5, C.P. 42076 Pachuca, Hidalgo (Mexico); Barrado, E. [QUIANE/Dept Quimica Analitica, F. de Ciencias, Universidad de Valladolid, Prado de la Magdalena s/n, 47005 Valladolid (Spain)

    2011-10-01

    This work concerns the electrochemical extraction of samarium from molten chlorides. In this way, the electrochemical behaviour of samarium ions has been investigated in the eutectic LiCl-KCl at the surface of tungsten, aluminium and aluminium coated tungsten electrodes. On a W inert electrode the electro-reduction of Sm(III) takes place in only one soluble-soluble electrochemical step Sm(III)/Sm(II). The electrochemical system Sm(II)/Sm(0) has not been observed within the electrochemical window, because of the prior reduction of Li(I) ions from the solvent, which inhibits the electro-extraction of Sm species from the salt on such a substrate. Sm metal in contact with the melt react to give Li(0) according to the reaction: Sm(0) + 2Li(I) {r_reversible} Sm(II) + 2Li(0). On the contrary, on reactive Al electrodes the electrochemical system Sm(II)/Sm(0) was observed within the electroactive range. The potential shift of the redox couple is caused by the decrease of Sm activity in the metal phase due to the formation of Sm-Al alloys at the interface. The formation mechanism of the intermetallic compounds was studied in a melt containing: (i) both Sm(III) and Al(III) ions, using W and Al coated tungsten electrodes, and (ii) Sm(III) ions using an Al electrode. Analysis of the samples after potentiostatic electrolysis by X-ray diffraction and scanning electron microscopy (SEM) with energy dispersive X-ray spectroscopy (EDS), allowed the identification of Al{sub 3}Sm and Al{sub 2}Sm.

  5. Electrochemistry of Molten Sulfides: Copper Extraction from BaS-Cu[subscript 2]S

    OpenAIRE

    Sokhanvaran, Samira; Lee, Sang-Kwon; Lambotte, Guillaume; Allanore, Antoine

    2015-01-01

    The electrolytic extraction of liquid copper at 1105°C from a molten sulfide electrolyte composed of 57 wt% BaS and 43 wt% Cu[subscript 2]S was investigated. DC cyclic voltammetry, Fourier transformed AC voltammetry, and galvanostatic electrolysis revealed that the electrodeposition of copper is possible in the selected molten sulfide electrolyte. The half wave potential for the reaction on graphite was determined, and liquid copper of high purity was obtained by galvanostatic electrolysis. T...

  6. Molten salt extraction of transuranic and reactive fission products from used uranium oxide fuel

    Science.gov (United States)

    Herrmann, Steven Douglas

    2014-05-27

    Used uranium oxide fuel is detoxified by extracting transuranic and reactive fission products into molten salt. By contacting declad and crushed used uranium oxide fuel with a molten halide salt containing a minor fraction of the respective uranium trihalide, transuranic and reactive fission products partition from the fuel to the molten salt phase, while uranium oxide and non-reactive, or noble metal, fission products remain in an insoluble solid phase. The salt is then separated from the fuel via draining and distillation. By this method, the bulk of the decay heat, fission poisoning capacity, and radiotoxicity are removed from the used fuel. The remaining radioactivity from the noble metal fission products in the detoxified fuel is primarily limited to soft beta emitters. The extracted transuranic and reactive fission products are amenable to existing technologies for group uranium/transuranic product recovery and fission product immobilization in engineered waste forms.

  7. Pure metal extraction from molten oxide slag by short-circuit galvanic cell

    Institute of Scientific and Technical Information of China (English)

    Yunming Gao; Xingmin Guo; Kuochih Chou

    2004-01-01

    The oxygen-ion-permeable membrane galvanic short-circuit method has been developed, in which pure metal was directly extracted from the molten oxide slag, and no external voltage is applied. The galvanic cell employed in the experiment was as follows: graphite rod|[O]Fe+C saturation|ZrO2(MgO)|(FeO)(siag) |Fe rod. The reduction current in the galvanic cell consisted of an external short-circuit current and an interior short-circuit current in the oxygen-ion-permeable membrane. The real-time variation of external circuit reduction ratio of the molten slag could be obtained from the curve of the external circuit current to the time.

  8. Pyrochemical reprocessing of molten salt fast reactor fuel: focus on the reductive extraction step

    Directory of Open Access Journals (Sweden)

    Rodrigues Davide

    2015-12-01

    Full Text Available The nuclear fuel reprocessing is a prerequisite for nuclear energy to be a clean and sustainable energy. In the case of the molten salt reactor containing a liquid fuel, pyrometallurgical way is an obvious way. The method for treatment of the liquid fuel is divided into two parts. In-situ injection of helium gas into the fuel leads to extract the gaseous fission products and a part of the noble metals. The second part of the reprocessing is performed by ‘batch’. It aims to recover the fissile material and to separate the minor actinides from fission products. The reprocessing involves several chemical steps based on redox and acido-basic properties of the various elements contained in the fuel salt. One challenge is to perform a selective extraction of actinides and lanthanides in spent liquid fuel. Extraction of actinides and lanthanides are successively performed by a reductive extraction in liquid bismuth pool containing metallic lithium as a reductive reagent. The objective of this paper is to give a description of the several steps of the reprocessing retained for the molten salt fast reactor (MSFR concept and to present the initial results obtained for the reductive extraction experiments realized in static conditions by contacting LiF-ThF4-UF4-NdF3 with a lab-made Bi-Li pool and for which extraction efficiencies of 0.7% for neodymium and 14.0% for uranium were measured. It was concluded that in static conditions, the extraction is governed by a kinetic limitation and not by the thermodynamic equilibrium.

  9. Pyrochemical reprocessing of molten salt fast reactor fuel: focus on the reductive extraction step

    OpenAIRE

    Rodrigues Davide; Durán-Klie Gabriela; Delpech Sylvie

    2015-01-01

    The nuclear fuel reprocessing is a prerequisite for nuclear energy to be a clean and sustainable energy. In the case of the molten salt reactor containing a liquid fuel, pyrometallurgical way is an obvious way. The method for treatment of the liquid fuel is divided into two parts. In-situ injection of helium gas into the fuel leads to extract the gaseous fission products and a part of the noble metals. The second part of the reprocessing is performed by ‘batch’. It aims to recover the fissile...

  10. Solvent Extraction of Some Lanthanides with Trioctylphosphine Oxide in Molten Paraffin Wax

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    The extraction behavior of Ln(Ⅲ) (Ln=Nd, Sm, Tb and Yb) with trioctylphosphine oxide (TOPO) in molten paraffin wax has been studied. The effect of pH, TOPO concentration, medium, stirring time and the amount of salts added on the distribution of lanthanides between two phases were investigated. Two different compositions Ln(H2O)s€?(TOPO)2(OH)2NO3 (Ln=Nd and Sm) and Ln(H2O)s€?(TOPO)2(OH)(NO3)2 (Ln=Tb and Yb) were determined by slope analysis method. The equilibrium extraction constant Kex and pH1/2 value were calculated and the thermodynamic parameters were obtained from the dependence of Kex on the temperature.

  11. Correlation between molten vanadium salts and the structural degradation of HK-type steel superheater tubes

    Science.gov (United States)

    de Carvalho Nunes, Frederico; de Almeida, Luiz Henrique; Ribeiro, André Freitas

    2006-12-01

    HK steels are among the most used heat-resistant cast stainless steels, being corrosion-resistant and showing good mechanical properties at high service temperatures. These steels are widely used in reformer furnaces and as superheater tubes. During service, combustion gases leaving the burners come in contact with these tubes, resulting in corrosive attack and a large weight loss occurs due to the presence of vanadium, which forms low melting point salts, removing the protective oxide layer. In this work the external surface of a tube with dramatic wall thickness reduction was analyzed using light microscopy, scanning electron microscopy, and transmission electron microscopy. The identification of the phases was achieved by energy dispersive spectroscopy (EDS) analyses. The results showed oxides arising from the external surface. In this oxidized region vanadium compounds inside chromium carbide particles were also observed, due to inward vanadium diffusion during corrosion attack. A chemical reaction was proposed to explain the presence of vanadium in the metal microstructure.

  12. Liquid-liquid reductive extraction in molten fluoride salt/liquid aluminium as a core of process for the An/Ln group separation

    Energy Technology Data Exchange (ETDEWEB)

    Conocar, O

    2007-06-15

    This report concerns a pyrochemical process based on liquid-liquid extraction in a molten fluoride/liquid aluminium system as a core process for actinide (An)/lanthanide (Ln) group separation, studied at CEA. The basic and demonstrative experiments have established the feasibility of the An/Ln group separation in the molten fluoride/liquid aluminium system (U, Pu, Np, Am, Cm traces from Nd, Ce, Eu, Sm, Eu, La - An/Ln separation factors over 1000 - An recovery yield over 98 % in one batch). The main experimental efforts must now be targeted on the recovery of actinides from the Al matrix. A thermodynamic and bibliographical survey has been done. It shows that back-extraction in a molten chloride melt could be a promising technique for this purpose.

  13. Actinides-lanthanides (neodymium) separation by electrolytical extraction in molten fluoride media; Separation actinides-lanthanides (neodyne) par extraction electrolytique en milieux fluorures fondus

    Energy Technology Data Exchange (ETDEWEB)

    Hamel, C

    2005-02-15

    The aim of this thesis is to assess the potentialities of pyrochemical processes for futur nuclear fuels and Generation IV reactors (more particularly molten salt reactors). This study concerns the Actinides-Lanthanides and Lanthanides-Solvent separation by electrolytical extraction in molten fluoride media at high temperature. Three elements are selected for this study: neodymium (NdF{sub 3}), uranium (UF{sub 4}) and plutonium (PuF{sub 3}). Firstly, the electrochemical study of these three compounds in molten fluoride media is performed to evaluate the separations. Electrodeposition processes are studied and the values of formal potentials of U(III)/U(0), Pu(III)/Pu(0) and Nd(III)/Nd(0) are obtained in LiF-CaF{sub 2} eutectic mixture. Thermodynamically, the values of potentials differences are enough to separate U-Nd and Pu-Nd with a yield of extraction of 99.99%; this value is just sufficient for the Pu-Nd separation. Concerning the Nd-solvent separation this potential difference is too small. Next, the electrodeposition of solid metals on inert electrodes is performed. This study showed that the uranium and neodymium deposits are unstable in several fluoride media. In addition, the presence of salts in the dendritic metal is observed for the U solid deposits. Finally, a reactive cathode is used to improve these separation results and the shape of the deposits. The experimental results on nickel electrodes showed an improvement of the Pu-Nd separation and the Nd-solvent separation with the depolarisation phenomenon of the metal deposit on the nickel. Moreover, U and Nd metal are stabilized in the alloy which allows the elimination of reactions with the solvent as observed for the solid deposit. The formation of liquids alloys makes also easier the recovery of these three. (author)

  14. Actinides-lanthanides (neodymium) separation by electrolytic extraction in molten fluoride media; Separation actinides-lanthanides (neodyne) par extraction electrolytique en milieux fluorures fondus

    Energy Technology Data Exchange (ETDEWEB)

    Hamel, C

    2005-02-15

    The aim of this thesis is to assess the potentialities of pyrochemical processes for future nuclear fuels and Generation IV reactors (more particularly molten salt reactors). This study concerns the Actinides-Lanthanides and Lanthanides-Solvent separation by electrolytic extraction in molten fluoride media at high temperature. Three elements are selected for this study: neodymium (NdF{sub 3}), uranium (UF{sub 4}) and plutonium (PuF{sub 3}). Firstly, the electrochemical study of these three compounds in molten fluoride media is performed to evaluate the separations. Electrodeposition processes are studied and the values of formal potentials of U(III)/U(0), Pu(III)/Pu(0) and Nd(III)/Nd(0) are obtained in LiF-CaF{sub 2} eutectic mixture. Thermodynamically, the values of potentials differences are enough to separate U-Nd and Pu-Nd with a yield of extraction of 99.99%; this value is just sufficient for the Pu-Nd separation. Concerning the Nd-solvent separation this potential difference is too small. Next, the electrodeposition of solid metals on inert electrodes is performed. This study showed that the uranium and neodymium deposits are unstable in several fluoride media. In addition, the presence of salts in the dendritic metal is observed for the U solid deposits. Finally, a reactive cathode is used to improve these separation results and the shape of the deposits. The experimental results on nickel electrodes showed an improvement of the Pu-Nd separation and the Nd-solvent separation with the depolarization phenomenon of the metal deposit on the nickel. Moreover, U and Nd metal are stabilized in the alloy which allows the elimination of reactions with the solvent as observed for the solid deposit. The formation of liquids alloys makes also easier the recovery of these three. (author)

  15. Direct Extraction of Ti and Ti Alloy from Ti-Bearing Dust Slag in Molten CaCl2

    Science.gov (United States)

    Chen, Chaoyi; Zhao, Chong; Li, Junqi; Yang, Shufeng

    2016-06-01

    Using process of solid oxygen-ion conducting membrane (SOM), titanium metal and its alloy can be prepared directly from Ti-bearing dust slag by immersing it in the molten CaCl2 at 1,100℃, which has been proposed by constant voltage of 3.5 V for 2-6 h. The dust slag was ball-milled and pressed into pellets, then employed as the cathode, while the liquid copper, which was saturated with graphite powder and encased in yttria-stabilized zirconia (YSZ) tube, acted as the anode. The effect of forming pressure and electrolytic time on products was analyzed. The results show that the content of titanium increased with electrolytic time and the characteristic morphology presents as granule. Ti-Fe alloy can be obtained from Ti-Fe residue by 6 h electrolysis. For titanium-rich residue, when the forming pressure of pellets decreased from 6 to 3 MPa, only electrolysis for more than 4 h can completely remove the oxygen, and pure titanium is obtained by 6 h electrolysis. Besides, there is an unprecedented finding that the porous cathode is conducive to the removal of impurity elements.

  16. Trace Analysis of Metals Using Naphthalene Part I Spectrophotometric Determination of Cobalt after Extraction of Its Chinoform Complex with Molten Naphthalene

    OpenAIRE

    SATAKE, Masatada; PURl, Bal K.; YUH, Ju Chieng; CHANG, Lih-Fen

    1982-01-01

    A new method is described for naphthalene extraction andspectrophotometric determination of trace cobalt with chinoform.The method is based on the formation of the colored complex whichis extractable with molten naphthalene and on the dissolution ofthe extract in dimethylformamide. This solution follows Beer'slaw at 428 nm over the range of 3-43 μg of cobalt per 10 ml ofdimethylformamide. The color of the complex is stable for 90min. The various factors such as pH, amounts of reagent andnapht...

  17. Study of Neodymium Extraction in Molten Fluorides by Electrochemical Co-Reduction with Aluminium

    Energy Technology Data Exchange (ETDEWEB)

    Gibilaro, M.; Massot, L.; Chamelot, P.; Taxil, P. [Laboratoire de Genie Chimique UMR 5503, Departement Procedes Electrochimiques, Universite de Toulouse, 31062 Toulouse Cedex 9 (France)

    2008-07-01

    This work concerns the co-deposition process of Al-Nd alloys in LiF-CaF{sub 2} medium (79-21% mol.) on tungsten electrode at 860 deg. C using electrochemical techniques: cyclic and square wave voltammetries and potentiostatic electrolysis. Specific peaks of Al-Nd alloys formation were observed in cyclic voltammograms between the reduction waves of Nd(III) and Al(III), in a fluoride melt containing neodymium and aluminium ions. The difference of potential measured between solvent reduction and the alloys formation allows expecting an extraction efficiency of 99.99% by the use of the co-reduction process. The intermetallic compounds (Al{sub 11}Nd{sub 3}, Al{sub 3}Nd, AlNd{sub 2} and AlNd{sub 3}) were obtained and characterised by Scanning Electron Microscopy with EDS probe. The validity of the process was tested by carrying neodymium extraction in the form of Al-Nd alloy; the extraction efficiency was more than 95%. (authors)

  18. Molten solvent extraction behavior of trivalent La, Sm, Dy, and Yb withtri-n-butyl phosphate into molten paraffin wax at 60 ℃

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    The extraction behavior of La3+, Sm3+, Dy3+, and Yb3+ in sodium acetate-acetic acid medium was studied with tri-n-butyl phosphate (TBP) at 60 ℃ using paraffin wax as a diluent. The extraction percentage is greater than 85% in the pH range of 6 to 8. The result of slope analysis method indicates that the compositions of the extracted species are different between the light and heavy rare earths. The formula of the extracted species is found to be La(TBP)(OH)(Ac)2for La3+ and Yb(TBP)(OH)3 for Yb3+. The effects of extracting time, the concentration of TBP in the organic phase and salts on the extraction efficiency were also discussed.

  19. Extraction of o-phenylphenol from silicone tubing by a sulfobutylether cyclodextrin formulation.

    Science.gov (United States)

    Zimmerman, Jeffrey A; Ballard, John M; Wang, Hai; Wu, Allen; Gallagher, Kimberly A

    2003-11-28

    During a compatibility study between a formulation containing sulfobutylether cyclodextrin (SBECD) and silicone tubing, an extraneous peak was observed in the HPLC chromatograms. The extraneous material was identified by LC/MS, MS/MS and UV as a previously unreported tubing extractable, o-phenylphenol (o-PP). Several studies were conducted to assess the impact of formulation and process-related variables on the amount of the o-PP extracted, including contact time, sulfobutylether cyclodextrin concentration, formulation pH, and tubing sterilization and storage conditions. Results show that the concentration of the SBECD, tubing processing and storage conditions and the duration of the study influenced the levels of o-PP extracted. However, the largest contributor to the amount extracted was the lot of tubing tested. The extracted levels varied widely from lot to lot (0.007-3.89microg/cm(2) of tubing surface area). A dynamic study conducted to simulate a manufacturing process also resulted in the extraction of o-PP by the formulation.

  20. PARTICULARITIES REGARDING THE OPERATING PROCESS OF THE CUTTING AND EXTRACTION DEVICE IN THE CANDU HORIZONTAL FUEL CHANNELS PRESSURE TUBE DECOMMISSIONING PART II: CUTTING AND EXTRACTING PRESSURE TUBE PROCESS

    Directory of Open Access Journals (Sweden)

    Constantin POPESCU

    2016-05-01

    Full Text Available This paper presents some details of operation process for a Cutting and Extraction Device (CED in order to achieve the decommissioning of the horizontal fuel channels pressure tube in the CANDU 6 nuclear reactor. The most important characteristic of the Cutting and Extraction Device (CED is his capability of totally operator’s protection against the nuclear radiation during pressure tube decommissioning. The cutting and extracting pressure tube processes present few particularities due to special adopted technical solutions: a special module with three cutting rollers (system driven by an actuator, a guiding-extracting and connecting module (three fixing claws which are piloted by an actuator and block the device in the connecting position with extracting plugs. The Cutting and Extraction Device (CED is a train of modules equipped with special systems to be fully automated, connected with a Programmable Logic Controller (PLC and controlled by an operator panel type Human Machine Interface (HMI. All processes are monitored by video cameras. In case of error, the process is automatically stopped, the operator receiving an error message and the last sequence could be reinitialized or aborted due to safety reasons.

  1. A new cooperation mechanism of kinesin motors when extracting membrane tube

    CERN Document Server

    Wang, Ziqing

    2011-01-01

    Membrane tubes are important elements for living cells to organize many functions. Experiments have found that membrane tube can be extracted from giant lipid vesicles by a group of kinesin. How these motors cooperate in extracting the fluid-like membrane tube is still unclear. In this paper, we propose a new cooperation mechanism called two-track-dumbbell model, in which kinesin is regarded as a dumbbell with an end (tail domain) tightly bound onto the fluid-like membrane and the other end (head domain) stepping on or unbinding from the microtubule. Taking account of the elasticity of kinesin molecule and the exclude volume effect of both the head domain and the tail domain of kinesin, which are not considered in previous models, we simulate the growth process of the membrane tube pulled by kinesin motors. Our results indicate that motors along a single microtubule protofilament can generate enough force to extract membrane tubes from vesicles, and the average number of motors pulling the tube is about 8~9. ...

  2. Electrolysis of a molten semiconductor

    Science.gov (United States)

    Yin, Huayi; Chung, Brice; Sadoway, Donald R.

    2016-08-01

    Metals cannot be extracted by electrolysis of transition-metal sulfides because as liquids they are semiconductors, which exhibit high levels of electronic conduction and metal dissolution. Herein by introduction of a distinct secondary electrolyte, we reveal a high-throughput electro-desulfurization process that directly converts semiconducting molten stibnite (Sb2S3) into pure (99.9%) liquid antimony and sulfur vapour. At the bottom of the cell liquid antimony pools beneath cathodically polarized molten stibnite. At the top of the cell sulfur issues from a carbon anode immersed in an immiscible secondary molten salt electrolyte disposed above molten stibnite, thereby blocking electronic shorting across the cell. As opposed to conventional extraction practices, direct sulfide electrolysis completely avoids generation of problematic fugitive emissions (CO2, CO and SO2), significantly reduces energy consumption, increases productivity in a single-step process (lower capital and operating costs) and is broadly applicable to a host of electronically conductive transition-metal chalcogenides.

  3. 2-Hydroxypropyl-beta-cyclodextrin extracts 2-phenylphenol from silicone tubing.

    Science.gov (United States)

    den Brok, Monique W J; van der Schoot, Sabien C; Nuijen, Bastiaan; Hillebrand, Michel J X; Beijnen, Jos H

    2004-07-08

    Cyclodextrins are capable to solubilise lipophilic drugs via (partial) inclusion in their lipophilic cavity. This, however, also provides the potential for the extraction of small molecules from production materials. In the present study, the potency of the commercially available and used cyclodextrin, 2-hydroxypropyl-beta-cyclodextrin (HPbetaCD) to extract the preservative 2-phenylphenol (2-PP) from platinum cured silicone tubing was tested. The presence of 2-PP was structurally confirmed with HPLC-UV and LC/MS/MS in HPbetaCD solutions after incubation with platinum cured silicone tubing. HPbetaCD concentration and prior tubing sterilisation were found not to influence the levels of 2-PP extracted. Interestingly, extraction to ethanol was 15-fold higher than observed for HPbetaCD solutions. 2-PP was extracted from silicone tubing during routine manufacture of a blank dosage form formulated with only HPbetaCD, resulting in detectable levels of 2-PP in the final product. In a freeze-dried dosage form containing HPbetaCD and an active pharmaceutical ingredient (exhibiting a stability constant for HPbetaCD/drug of 1045 L/mol), on the other hand, 2-PP was undetectable.

  4. 高温熔融盐壳管式相变换热器的传热特性%Heat Transfer Performances of High-Temperature Shell-Tube Heat Exchanger with Molten-Salt Phase Change Materials

    Institute of Scientific and Technical Information of China (English)

    左远志; 杨晓西; 丁静

    2011-01-01

    建立了高温熔融盐壳管式相变换热器的同心套管模型.采用Fluent软件,分析了在考虑相变区域自然对流条件下,熔融盐流体与相变材料的物性参数、内管进口温度与进口流向等因素对液相率与熔化时间的影响,并在熔融盐传热-蓄热实验平台上进行了试验研究.发现:考虑相变区域自然对流时,总的熔化时间减少16.2%;模拟得到的壳侧相变材料温度随时间的变化趋势与实验结果趋于一致.结果表明,可采用熔融盐相变区域特殊测点温度超过相变材料的熔点,并升至与内管流体进口温度相近时所耗费的时间作为壳管式相变换热器内相变材料完全熔化的判据.%In this paper, first, a concentric circular tube model for the shell-tube heat exchanger with molten-salt phase change materials (PCMs) is established. Then, the liquid fraction and the total melting time, which are affected by the thermal-physical parameters of the molten salt fluid and the PCMs as well as by the inlet velocity and the flow direction of the inner tube, are analyzed with Fluent, by taking into consideration the natural convection in the PCMs region. Finally, some experiments are carried out on a test platform of molten-salt heat transfer. The resuits show that the total melting time nearly decreases by 16. 2% considering the natural convection in the PCMs region, and that the simulated temperature of PCMs at the shell side varies with time,which has a tendency similar to that of the experimental results. Thus, it comes to the conclusion that, when the temperature of the specific measuring point in the PCMs region exceeds the melting point of PCMs and rises to the tube inlet temperature, the correspending time cost can be used as the criterion of melting ending of PCMs.

  5. 熔融钒渣直接提钒新工艺%New Process of Vanadium Extraction from Molten Vanadium Slag

    Institute of Scientific and Technical Information of China (English)

    宋文臣; 李宏; 李昆; 郑权

    2013-01-01

    现行钒渣焙烧工艺中的钒渣高温物理热被浪费,对“熔融钒渣直接氧化钠化提钒”新工艺的可行性进行分析,并进行实验室模拟试验.结果表明,新工艺条件下,试验过程中熔融钒渣流动性良好,焙烧后钒渣水浸率为50%~80%,焙烧后钒渣中的钒主要以偏钒酸钠的形式存在.新工艺是合理可行的,具有工业生产价值.%A new process of extracting vanadium from molten vanadium slag by direct oxidation and sodium salt roasting method was introduced,with the aim to address heat waste of vanadium slag existing in vanadium extraction process through vanadium slag roasting.The feasibility of the new process was analyzed,and the simulation test was carried out in laboratory.The results show that under the new process condition,molten vanadium slag can be kept with good fluidity.Water leaching rate of vanadium is 50 % ~80 %.Vanadium in roasted slag exists in form of sodium metavanadate.To conclude,the new process is feasible and can meet industrial production requirement.

  6. Spectrophotometric determination of copper in environmental samples by solid-liquid extraction of its 9, 10-phenanthrenequinone monoximate complex into molten naphthalene

    Energy Technology Data Exchange (ETDEWEB)

    Wasey, A.; Puri, B.K.; Katyal, M.; Satake, M.

    1986-01-01

    A fairly selective and sensitive spectrophotometric method has been developed for determination of copper after extraction of its 9, 10-phenanthrenequinone monoximate complex into molten naphthalene in the pH range of 6.1-8.4. At room temperature, the solid naphthalene containing the metal complex is separated by filtration, dissolved in dimethylformamide (DMF) and the absorbance measured at 470 nm against the reagent blank. Beer's law is obeyed in the concentration range, 0.0-9.6 micrograms of copper in 10ml of DMF. The molar absorptivity and sensitivity are 6.30 X 10(4) 1 mol-1 cm-1 and 0.001 micrograms cm-2, respectively. The interference of various ions has been studied and the method has been applied for the determination of copper in various standard reference materials, beers, wines, human hair and environmental samples.

  7. Destructive examination of defected S/G tubes extracted from Uljin unit 1

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Joung Soo; Hahn, J. H.; Kim, H. P.; Lee, D. H. [Korea Atomic Energy Research Institute, Taejon (Korea)

    1999-10-01

    Destructive examination was performed using the defected tubes having been extracted from Uljin unit 1, the commercial operation of which had started in 1998. The results of the examination are as follow: 1) Primary cause of the defect formed in the tubes was found to be high susceptibility of the tube materials having microstructures known to be easily subjected to PWSCC.(high carbon content, low temperature mill annealed, intragranular carbide precipitation, small grain size, high strength) 2) Criteria for tube plugging and/or sleeving should be established by the judgement of the extend of increase in ECT amplitude instead of that in the crack length. 3) The evaluation of the ECT results using the axial coil signals would be more reliable than by using the pancake coil signal. 4) The maximum leak rate to be allowed at Uljin unit 1 can be raised to 10 l/hr. 5) The residual life of the steam generators at Uljin unit 1 would be 10 years more. 6) The difference in failure rate and leak rate between Uljin unit 1 and similar French units to Uljin unit 1 is assumed to come from the difference in operating conditions. 131 figs., 24 tabs. (Author)

  8. Electrolysis of a molten semiconductor

    Science.gov (United States)

    Yin, Huayi; Chung, Brice; Sadoway, Donald R.

    2016-01-01

    Metals cannot be extracted by electrolysis of transition-metal sulfides because as liquids they are semiconductors, which exhibit high levels of electronic conduction and metal dissolution. Herein by introduction of a distinct secondary electrolyte, we reveal a high-throughput electro-desulfurization process that directly converts semiconducting molten stibnite (Sb2S3) into pure (99.9%) liquid antimony and sulfur vapour. At the bottom of the cell liquid antimony pools beneath cathodically polarized molten stibnite. At the top of the cell sulfur issues from a carbon anode immersed in an immiscible secondary molten salt electrolyte disposed above molten stibnite, thereby blocking electronic shorting across the cell. As opposed to conventional extraction practices, direct sulfide electrolysis completely avoids generation of problematic fugitive emissions (CO2, CO and SO2), significantly reduces energy consumption, increases productivity in a single-step process (lower capital and operating costs) and is broadly applicable to a host of electronically conductive transition-metal chalcogenides. PMID:27553525

  9. [Determination of alkyl-phenols in textiles by in-tube capillary solid-phase extraction-gas chromatography].

    Science.gov (United States)

    Zhang, Luohong; Du, Ting; Zhong, Jiayu

    2015-10-01

    An in-tube capillary solid-phase extraction (SPE) -gas chromatography (GC) method was developed for confirmation and quantitative determination of octylphenol (OP) and nonylphenol (NP) in textiles. To make the in-tube capillary SPE column, the best SPE cartridge was chosen from four kinds of SPE cartridges. The adsorbent in the cartridge was used as the filling material to make the in-tube capillary SPE column. The nature, volume used, flow rate and adsorption capacity of the eluent were compared. Finally, the in-tube capillary solid-phase extraction was combined with gas chromatography to detect the alkyl phenols (APs). Abselut NEXUS extraction cartridge was chosen as the best solid phase extractant. The optimal in-tube capillary SPE extraction conditions were as follows: 1.2 μL methanol and 1.2 μL ultra-pure water for activating the extraction column, 1.2 μL methanol for eluting, 0.4 μL/min for solution loading. The method showed a good linear relationship in the low concentration range, and the enrichment ratios for the APs were about 100 times. The detection limits of octylphenol and nonylphenol were 3.7 μg/L and 4.5 μg/L, respectively. The recoveries of octylphenol were 85.6%-98.2%, and those of nonylphenol were 83.8%-95.7%. The experimental results demonstrated that the method is simple, rapid, and useful for detecting APs in textiles.

  10. A rapid and inexpensive one-tube genomic DNA extraction method from Agrobacterium tumefaciens.

    Science.gov (United States)

    Kamble, Suresh P; Fawade, Madhukar M

    2014-04-01

    Many methods have been used to isolate genomic DNA, but some of them are time-consuming and costly, especially when extracting a large number of samples. Here we described an easy protocol using two simple solutions for DNA extraction from A. tumefaciens cells. Compared with the standard protocol, this protocol allows rapid DNA isolation with comparable yield and purity at negligible cost. Following this protocol, we have demonstrated: (1) gDNA extraction was achieved within 15 min; (2) this method was cost-effective, since it only used calcium chloride and lysozyme; SDS, phenol, chloroform and proteinase K were not necessary; (3) the method gave high yield of gDNA (130 ng/loopful culture) compared with standard protocol that was suitable for restriction analysis; (4) the protocol can be carried out in a single test tube and the cells directly from solid media can be used. Thus, this protocol offers an easy, efficient and economical way to extract genomic DNA from A. tumefaciens.

  11. Electrochemical extraction of neodymium by co-reduction with aluminum in LiCl-KCl molten salt

    Science.gov (United States)

    Yan, Yong-De; Xu, Yan-Lu; Zhang, Mi-Lin; Xue, Yun; Han, Wei; Huang, Ying; Chen, Qiong; Zhang, Zhi-Jian

    2013-02-01

    The electrochemical behavior of Nd(III) ions in LiCl-KCl and LiCl-KCl-AlCl3 melts on a Mo electrode at 723 K was studied by various electrochemical techniques. The results showed that Nd(III) ions are reduced to Nd(0) through two consecutive steps, and the underpotential deposition of neodymium on pre-deposited Al electrode formed two kinds of Al-Nd intermetallic compounds in LiCl-KCl-AlCl3 solutions. The electrochemical extraction of neodymium was carried out in LiCl-KCl-AlCl3 melts on a Mo electrode at 873 K by potentiostatic and galvanostatic electrolysis. The extraction efficiency was 99.25% after potentiostatic electrolysis for 30 h. Al-Li-Nd bulk alloy was obtained by galvanostatic electrolysis. X-ray diffraction (XRD) suggested that Al2Nd and Al3Nd phases were formed in Al-Li-Nd alloy. The microstructure and micro-zone chemical analysis of Al-Li-Nd alloy were characterized by scanning electron microscopy (SEM) with energy dispersive spectrometry (EDS), respectively.

  12. Electrochemical extraction of neodymium by co-reduction with aluminum in LiCl–KCl molten salt

    Energy Technology Data Exchange (ETDEWEB)

    Yan, Yong-De, E-mail: y5d2006@hrbeu.edu.cn [Key Discipline Laboratory of Nuclear Safety and Simulation Technology, Harbin Engineering University, Harbin 150001 (China); Key Laboratory of Superlight Materials and Surface Technology, Ministry of Education, College of Materials Science and Chemical Engineering, Harbin Engineering University, Harbin 150001 (China); Xu, Yan-Lu [Key Laboratory of Superlight Materials and Surface Technology, Ministry of Education, College of Materials Science and Chemical Engineering, Harbin Engineering University, Harbin 150001 (China); Zhang, Mi-Lin, E-mail: zhangmilin@hrbeu.edu.cn [Key Laboratory of Superlight Materials and Surface Technology, Ministry of Education, College of Materials Science and Chemical Engineering, Harbin Engineering University, Harbin 150001 (China); Xue, Yun [Key Discipline Laboratory of Nuclear Safety and Simulation Technology, Harbin Engineering University, Harbin 150001 (China); Key Laboratory of Superlight Materials and Surface Technology, Ministry of Education, College of Materials Science and Chemical Engineering, Harbin Engineering University, Harbin 150001 (China); Han, Wei; Huang, Ying; Chen, Qiong [Key Laboratory of Superlight Materials and Surface Technology, Ministry of Education, College of Materials Science and Chemical Engineering, Harbin Engineering University, Harbin 150001 (China); Zhang, Zhi-Jian [Key Discipline Laboratory of Nuclear Safety and Simulation Technology, Harbin Engineering University, Harbin 150001 (China)

    2013-02-15

    The electrochemical behavior of Nd(III) ions in LiCl–KCl and LiCl–KCl–AlCl{sub 3} melts on a Mo electrode at 723 K was studied by various electrochemical techniques. The results showed that Nd(III) ions are reduced to Nd(0) through two consecutive steps, and the underpotential deposition of neodymium on pre-deposited Al electrode formed two kinds of Al–Nd intermetallic compounds in LiCl–KCl–AlCl{sub 3} solutions. The electrochemical extraction of neodymium was carried out in LiCl–KCl–AlCl{sub 3} melts on a Mo electrode at 873 K by potentiostatic and galvanostatic electrolysis. The extraction efficiency was 99.25% after potentiostatic electrolysis for 30 h. Al–Li–Nd bulk alloy was obtained by galvanostatic electrolysis. X-ray diffraction (XRD) suggested that Al{sub 2}Nd and Al{sub 3}Nd phases were formed in Al–Li–Nd alloy. The microstructure and micro-zone chemical analysis of Al–Li–Nd alloy were characterized by scanning electron microscopy (SEM) with energy dispersive spectrometry (EDS), respectively.

  13. Lanthanides electrolytic extraction from molten fluoride by alloy formation; Extraction electrochimique des lanthanides des milieux de fluorures fondus par formation d'alliages

    Energy Technology Data Exchange (ETDEWEB)

    Nourry, Ch

    2007-10-15

    This work consisted in studying the electrochemical behaviour of some dissolved lanthanides (Gd, Nd, Sm) in LiF-CaF{sub 2} media on inert and reactive cathodes in the 800-920 C temperature range and then to estimate their possible extraction from the melt by reduction on a reactive electrode (Ni, Cu or Ni/Cu). Using electrochemical methods and SEM micrographs, reduction mechanisms and thermodynamic parameters such as standard potential and activity coefficient were determined for the different species in the melt. The Gibbs energies and the reduction mechanisms were determined for LnNi and LnCu compounds. Finally, extractions have been performed on reactive electrodes with very good extraction rate ({>=} 99.7%). (author)

  14. Two techniques enable sampling of filtered and unfiltered molten metals

    Science.gov (United States)

    Burris, L., Jr.; Pierce, R. D.; Tobias, K. R.; Winsch, I. O.

    1967-01-01

    Filtered samples of molten metals are obtained by filtering through a plug of porous material fitted in the end of a sample tube, and unfiltered samples are obtained by using a capillary-tube extension rod with a perforated bucket. With these methods there are no sampling errors or loss of liquid.

  15. Production of Oxygen from Lunar Regolith using Molten Oxide Electrolysis

    Science.gov (United States)

    Sibille, Laurent; Sadoway, Donald R.; Sirk, Aislinn; Tripathy, Prabhat; Melendez, Orlando; Standish, Evan; Dominquez, Jesus A.; Stefanescu, Doru M.; Curreri, Peter A.; Poizeau, Sophie

    2009-01-01

    This slide presentation reviews the possible use of molten oxide electrolysis to extract oxygen from the Lunar Regolith. The presentation asserts that molten regolith electrolysis has advanced to be a useful method for production of oxygen and metals in situ on the Moon. The work has demonstrated an 8 hour batch of electrolysis at 5 amps using Iridium inert anodes.

  16. Gases in molten salts

    CERN Document Server

    Tomkins, RPT

    1991-01-01

    This volume contains tabulated collections and critical evaluations of original data for the solubility of gases in molten salts, gathered from chemical literature through to the end of 1989. Within the volume, material is arranged according to the individual gas. The gases include hydrogen halides, inert gases, oxygen, nitrogen, hydrogen, carbon dioxide, water vapor and halogens. The molten salts consist of single salts, binary mixtures and multicomponent systems. Included also, is a special section on the solubility of gases in molten silicate systems, focussing on slags and fluxes.

  17. Molten Metal Burns

    OpenAIRE

    Kahn, Arthur M.; McCrady-Kahn, Virginia L.

    1981-01-01

    Molten metal burns are a frequent industrial injury among workers in foundries. The injury is typically small but very deep. Usually the depth and seriousness of these injuries is not recognized immediately by emergency department or industrial clinic physicians.

  18. System Requirements Document for the Molten Salt Reactor Experiment

    Energy Technology Data Exchange (ETDEWEB)

    Aigner, R.D.

    2000-04-01

    The purpose of the conversion process is to convert the {sup 233}U fluoride compounds that are being extracted from the Molten Salt Reactor Experiment (MSRE) equipment to a stable oxide for long-term storage at Bldg. 3019.

  19. Molten salts and nuclear energy production

    Science.gov (United States)

    Le Brun, Christian

    2007-01-01

    Molten salts (fluorides or chlorides) were considered near the beginning of research into nuclear energy production. This was initially due to their advantageous physical and chemical properties: good heat transfer capacity, radiation insensitivity, high boiling point, wide range solubility for actinides. In addition it was realised that molten salts could be used in numerous situations: high temperature heat transfer, core coolants with solid fuels, liquid fuel in a molten salt reactor, solvents for spent nuclear solid fuel in the case of pyro-reprocessing and coolant and tritium production in the case of fusion. Molten salt reactors, one of the six innovative concepts chosen by the Generation IV international forum, are particularly interesting for use as either waste incinerators or thorium cycle systems. As the neutron balance in the thorium cycle is very tight, the possibility to perform online extraction of some fission product poisons from the salt is very attractive. In this article the most important questions that must be addressed to demonstrate the feasibility of molten salt reactor will be reviewed.

  20. Molten salts and nuclear energy production

    Energy Technology Data Exchange (ETDEWEB)

    Le Brun, Christian [Laboratoire de Physique Subatomique et de Cosmologie, 53 Avenue des Martyrs, 38026 Grenoble cedex (France)]. E-mail: christian.lebrun@lpsc.in2p3.fr

    2007-01-15

    Molten salts (fluorides or chlorides) were considered near the beginning of research into nuclear energy production. This was initially due to their advantageous physical and chemical properties: good heat transfer capacity, radiation insensitivity, high boiling point, wide range solubility for actinides. In addition it was realised that molten salts could be used in numerous situations: high temperature heat transfer, core coolants with solid fuels, liquid fuel in a molten salt reactor, solvents for spent nuclear solid fuel in the case of pyro-reprocessing and coolant and tritium production in the case of fusion. Molten salt reactors, one of the six innovative concepts chosen by the Generation IV international forum, are particularly interesting for use as either waste incinerators or thorium cycle systems. As the neutron balance in the thorium cycle is very tight, the possibility to perform online extraction of some fission product poisons from the salt is very attractive. In this article the most important questions that must be addressed to demonstrate the feasibility of molten salt reactor will be reviewed.

  1. Conduit for high temperature transfer of molten semiconductor crystalline material

    Science.gov (United States)

    Fiegl, George (Inventor); Torbet, Walter (Inventor)

    1983-01-01

    A conduit for high temperature transfer of molten semiconductor crystalline material consists of a composite structure incorporating a quartz transfer tube as the innermost member, with an outer thermally insulating layer designed to serve the dual purposes of minimizing heat losses from the quartz tube and maintaining mechanical strength and rigidity of the conduit at the elevated temperatures encountered. The composite structure ensures that the molten semiconductor material only comes in contact with a material (quartz) with which it is compatible, while the outer layer structure reinforces the quartz tube, which becomes somewhat soft at molten semiconductor temperatures. To further aid in preventing cooling of the molten semiconductor, a distributed, electric resistance heater is in contact with the surface of the quartz tube over most of its length. The quartz tube has short end portions which extend through the surface of the semiconductor melt and which are lef bare of the thermal insulation. The heater is designed to provide an increased heat input per unit area in the region adjacent these end portions.

  2. The chemistry of molten salt mixtures: application to the reductive extraction of lanthanides and actinides by a liquid metal; Chimie des melanges de sels fondus. Application a l'extraction reductrice d'actinides et de lanthanides par un metal liquide

    Energy Technology Data Exchange (ETDEWEB)

    Finne, J

    2005-10-15

    The design of a process of An/Ln separation by liquid - liquid extraction can be used for on-line purification of the molten salt in a molten salt nuclear reactor (Generation IV) as well as reprocessing various spent fuels. In order to establish the chemical properties of An and Ln in molten salt mediums, E - pO{sub 2} - diagrams were established for the relevant chemical elements. With the purpose of checking the possibilities of separating the An from Ln, the real activity coefficients in liquid metals were measured. An experimental protocol was developed and validated on the Gd/Ga system. It was then transferred to radioactive environment to measure the activity coefficient of Pu in Ga. The results made it possible to estimate the effectiveness of the Pu extraction and its separation from Gd and Ce. The selectivity was shown to decrease with the temperature and Al and Ga showed a good selectivity between Pu and the Ce in fluoride medium. (author)

  3. Parametric study of natural circulation flow in molten salt fuel in molten salt reactor

    Science.gov (United States)

    Pauzi, Anas Muhamad; Cioncolini, Andrea; Iacovides, Hector

    2015-04-01

    The Molten Salt Reactor (MSR) is one of the most promising system proposed by Generation IV Forum (GIF) for future nuclear reactor systems. Advantages of the MSR are significantly larger compared to other reactor system, and is mainly achieved from its liquid nature of fuel and coolant. Further improvement to this system, which is a natural circulating molten fuel salt inside its tube in the reactor core is proposed, to achieve advantages of reducing and simplifying the MSR design proposed by GIF. Thermal hydraulic analysis on the proposed system was completed using a commercial computation fluid dynamics (CFD) software called FLUENT by ANSYS Inc. An understanding on theory behind this unique natural circulation flow inside the tube caused by fission heat generated in molten fuel salt and tube cooling was briefly introduced. Currently, no commercial CFD software could perfectly simulate natural circulation flow, hence, modeling this flow problem in FLUENT is introduced and analyzed to obtain best simulation results. Results obtained demonstrate the existence of periodical transient nature of flow problem, hence improvements in tube design is proposed based on the analysis on temperature and velocity profile. Results show that the proposed system could operate at up to 750MW core power, given that turbulence are enhanced throughout flow region, and precise molten fuel salt physical properties could be defined. At the request of the authors and the Proceedings Editor the name of the co-author Andrea Cioncolini was corrected from Andrea Coincolini. The same name correction was made in the Acknowledgement section on page 030004-10 and in reference number 4. The updated article was published on 11 May 2015.

  4. Studies on Hot Corrosion of the 2.25 Cr-1Mo Boiler Tube Steel and Its Weldments in the Molten Salt Na2SO4-60 pct V2O5 Environment

    Science.gov (United States)

    Kumar, Ravindra; Tewari, V. K.; Prakash, S.

    2007-01-01

    Hot corrosion is mainly due to the dissolution of protective oxides in the molten salt at the metal surface and their reprecipitation at some other sites as nonprotective porous mass. The hot corrosion attack along the grain boundaries leading to subsurface precipitation of oxides and sulfides also contributes to weakening of material. Ferritic steel with 2.25Cr 1Mo is used widely as a candidate material in the steam generating system of power plants. Hot corrosion studies were conducted on 2.25Cr-1Mo unwelded as well as welded steel specimens with molten salt coated after exposure at 900 °C under cyclic conditions. The thermogravimetric technique was used to establish the kinetics of corrosion X-ray diffraction (XRD); scanning electron microscopy/energy-dispersive analysis (SEM/EDAX) was used to analyze the corrosion products.

  5. 熔融钒渣直接氧化钠化提钒新工艺研究%A New Process for Vanadium Extraction from Molten Vanadium Slag by Direct Oxidation and Sodium Activating Method

    Institute of Scientific and Technical Information of China (English)

    宋文臣; 李宏

    2012-01-01

    To address the problem of heat waste of vanadium slag in the existing vanadium extraction process, a new process is proposed in this paper to extract vanadium from molten vanadium slag by direct oxidation and sodium activating method. On the basis of current vanadium extraction process, the new process was verified by thermodynamic and kinetic calculation and analysis, and then simulation tests were carried out in the laboratory. The results show that with enough heat, vanadium slag can be kept in molten state during the vanadium extraction process. The dynamic conditions of the new process are noticeably better than the existing process. The oxidization rate of vanadium slag is about 90% and vanadium leaching rate can reach 82% or above with enough oxygen and Na2CO3 content at 20% ~ 30% of vanadium slag' weight. Thus, the feasibility of the new process is confirmed by the results.%针对现行钒渣焙烧工艺中存在的钒渣高温物理热的浪费问题,提出“熔融钒渣直接氧化钠化提钒”新工艺.在现行工艺基础上,对新工艺进行了热力学和动力学的计算与分析,最后进行了新工艺的实验室模拟试验.研究结果表明:新工艺条件下,钒渣在反应过程中热量充足会保持良好的熔融状态;新工艺的动力学条件明显优越于现行工艺;实验室试验结果验证了新工艺的可行性,在供氧充足,Na2CO3用量为20%~30%的条件下,钒渣氧化率约为90%,钒浸出率在82%以上.

  6. Investigation of molten salt fast reactor

    Energy Technology Data Exchange (ETDEWEB)

    Kubota, Kenichi; Konomura, Mamoru [Japan Nuclear Cycle Development Inst., Tokai, Ibaraki (Japan)

    2002-05-01

    On survey research for practicability strategy of fast reactor (FR) (phase 1), to extract future practicability image candidates of FR from wide options, in addition to their survey and investigation objects of not only solid fuel reactors of conventional research object but also molten salt reactor as a flowing fuel reactor, investigation on concept of molten salt FR plant was carried out. As a part of the first step of the survey research for practicability strategy, a basic concept on plant centered at nuclear reactor facility using chloride molten salt reactor capable of carrying out U-Pu cycle was examined, to perform a base construction to evaluate economical potential for a practical FBR. As a result, a result could be obtained that because of inferior fuel inventory and heat transmission to those in Na cooling reactor in present knowledge, mass of reactor vessel and intermediate heat exchanger were to widely increased to expect reduction of power generation unit price even on considering cheapness of its fuel cycle cost. Therefore, at present step further investigation on concept design of the chloride molten salt reactor plant system is too early in time, and it is at a condition where basic and elementary researches aiming at upgrading of economical efficiency such as wide reduction of fuel inventory, a measure expectable for remarkable rationalization effect of reprocessing system integrating a reactor to a processing facility, and so on. (G.K.)

  7. In-tube extraction of volatile organic compounds from aqueous samples: an economical alternative to purge and trap enrichment.

    Science.gov (United States)

    Laaks, Jens; Jochmann, Maik A; Schilling, Beat; Schmidt, Torsten C

    2010-09-15

    A novel in-tube extraction device (ITEX 2) for headspace sampling was evaluated for GC/MS analysis of aqueous samples. Twenty compounds of regulatory and drinking water quality importance were analyzed, including halogenated hydrocarbons, BTEX compounds (benzene, toluene, ethylbenzene, xylenes), fuel oxygenates, geosmin, and 2-methylisoborneol. Five commercially available sorbent traps were compared for their compound specific extraction yield. On the basis of the results, a mixed bed trap was prepared and evaluated. The extraction parameters were optimized to yield maximum sensitivity within the time of a GC run, to avoid unnecessary downtime of the system. Method detection limits of 1-10 ng L(-1) were achieved for volatile organic compounds (VOCs), which is much lower than demands by regulatory limit values. The performance of the ITEX system is similar to that of purge and trap systems, but it requires lower sample volumes and is less prone to contamination, much simpler, more flexible, and affordable. Average relative standard deviations below 10% were achieved for all analytes, and recoveries from spiked tap water samples were between 90% and 103%, mostly. The extraction is nonexhaustive, removing a fraction of 7% to 55% of the target compounds, depending on the air-water partitioning coefficients. The method was also tested with nonsynthetic samples, including tap, pond, and reservoir water and different soft drinks.

  8. Preparation and evaluation of a novel molecularly imprinted polymer coating for selective extraction of indomethacin from biological samples by electrochemically controlled in-tube solid phase microextraction

    Energy Technology Data Exchange (ETDEWEB)

    Asiabi, Hamid [Department of Chemistry, Tarbiat Modares University, P.O. Box 14115-175, Tehran (Iran, Islamic Republic of); Yamini, Yadollah, E-mail: yyamini@modares.ac.ir [Department of Chemistry, Tarbiat Modares University, P.O. Box 14115-175, Tehran (Iran, Islamic Republic of); Seidi, Shahram; Ghahramanifard, Fazel [Department of Analytical Chemistry, Faculty of Chemistry, K.N. Toosi University of Technology, Tehran (Iran, Islamic Republic of)

    2016-03-24

    In the present work, an automated on-line electrochemically controlled in-tube solid-phase microextraction (EC-in-tube SPME) coupled with HPLC-UV was developed for the selective extraction and preconcentration of indomethacin as a model analyte in biological samples. Applying an electrical potential can improve the extraction efficiency and provide more convenient manipulation of different properties of the extraction system including selectivity, clean-up, rate, and efficiency. For more enhancement of the selectivity and applicability of this method, a novel molecularly imprinted polymer coated tube was prepared and applied for extraction of indomethacin. For this purpose, nanostructured copolymer coating consisting of polypyrrole doped with ethylene glycol dimethacrylate was prepared on the inner surface of a stainless-steel tube by electrochemical synthesis. The characteristics and application of the tubes were investigated. Electron microscopy provided a cross linked porous surface and the average thickness of the MIP coating was 45 μm. Compared with the non-imprinted polymer coated tubes, the special selectivity for indomethacin was discovered with the molecularly imprinted coated tube. Moreover, stable and reproducible responses were obtained without being considerably influenced by interferences commonly existing in biological samples. Under the optimal conditions, the limits of detection were in the range of 0.07–2.0 μg L{sup −1} in different matrices. This method showed good linearity for indomethacin in the range of 0.1–200 μg L{sup −1}, with coefficients of determination better than 0.996. The inter- and intra-assay precisions (RSD%, n = 3) were respectively in the range of 3.5–8.4% and 2.3–7.6% at three concentration levels of 7, 70 and 150 μg L{sup −1}. The results showed that the proposed method can be successfully applied for selective analysis of indomethacin in biological samples. - Graphical abstract: An automated on

  9. Feasibility of lead extraction from waste Cathode-Ray-Tubes (CRT) funnel glass through a lead smelting process.

    Science.gov (United States)

    Lv, Jianfang; Yang, Hongying; Jin, Zhenan; Ma, Zhiyuan; Song, Yan

    2016-11-01

    A novel and effective process for extracting lead from the hazardous waste Cathode Ray Tubes (CRT) funnel glass is presented. The technological breakthrough of this process is introducing the discarded CRT funnel glass to traditional lead smelting. In this study, the influences of amount of carbon addition, calcium-silicate ratio, temperature, holding time and funnel glass addition on lead extraction efficiency were investigated to determine the optimal operational parameters. With a glass addition of less than 30wt%, a high extraction yield of 97.5% of lead from the mixture of funnel glass and lead slag was successfully obtained by controlling the C/PbO molar ratio, CaO/SiO2 ratio, temperature, treatment time at 0.9, 0.8, 1200°C, 60min, respectively. The main crystalline phases of the residues were calcium silicate slag, and an amorphous glass phase appears at a glass addition more than 30wt%. Thermodynamic calculation shows that the proportion of liquid phase in the slag first increased and then decreased, when the addition of glass is increased, while the viscosity of the slag exhibited a continuous decrease. Thus, based on all the results, it is concluded that the process proposed in this paper is an effective and promising approach for reutilization of obsolete CRT funnel glass. Copyright © 2016 Elsevier Ltd. All rights reserved.

  10. Characterization of Volatile Components from Hüller Bitterer Hop Variety Using In-Tube Extraction GC-MS Analysis

    Directory of Open Access Journals (Sweden)

    Liana Claudia Salanță

    2015-05-01

    Full Text Available The composition of hop oil contributes to the aroma of beer and the essential oil profile of hop samples contains valuable information for brewers. The aim of this study was to characterize the Hüller Bitterer hop variety, during the development of hop cones, by analysis the composition of volatile oil using in-tube extraction gas chromatography–mass spectrometry (ITEX-GC–MS. The obtained results show that the ITEX-GC/MS method is suitable for the determination of volatile compounds from hop samples. A number of 60 compounds were separated and 50 of them were identified. The most important volatile compounds found in Hüller Bitterer hop variety belonging to the monoterpenes and sesquiterpenes classes are represented by: β-myrcene, β-caryophyllene and α-humulene. 

  11. Recent development in electrolytic formation of carbon nanotubes in molten salts

    Directory of Open Access Journals (Sweden)

    Chen G.Z.

    2003-01-01

    Full Text Available This article reviews the recent research development in the electrolytic production of carbon nano-tubes in molten salts. The experimental procedure and product morphologies of the electrolytic method are described in details. Different hypotheses of the carbon nano-tube formation mechanism in molten salts, particularly it relation with the erosion of the cathode, are compared and discussed. It is anticipated that the electrolytic method can potentially become a cheap and continuous process for the production of curved carbon nano-tubes, carbon sheathed metal nanowires and other carbon based nano-structures.

  12. Molten carbonate fuel cell

    Science.gov (United States)

    Kaun, T.D.; Smith, J.L.

    1986-07-08

    A molten electrolyte fuel cell is disclosed with an array of stacked cells and cell enclosures isolating each cell except for access to gas manifolds for the supply of fuel or oxidant gas or the removal of waste gas. The cell enclosures collectively provide an enclosure for the array and effectively avoid the problems of electrolyte migration and the previous need for compression of stack components. The fuel cell further includes an inner housing about and in cooperation with the array enclosure to provide a manifold system with isolated chambers for the supply and removal of gases. An external insulated housing about the inner housing provides thermal isolation to the cell components.

  13. Design and evaluation of synthetic silica-based monolithic materials in shrinkable tube for efficient protein extraction.

    Science.gov (United States)

    Alzahrani, Eman; Welham, Kevin

    2011-10-21

    Sample pretreatment is a required step in proteomics in order to remove interferences and preconcentrate the samples. Much research in recent years has focused on porous monolithic materials since they are highly permeable to liquid flow and show high mass transport compared with more common packed beds. These features are due to the micro-structure within the monolithic silica column which contains both macropores that reduce the back pressure, and mesopores that give good interaction with analytes. The aim of this work was to fabricate a continuous porous silica monolithic rod inside a heat shrinkable tube and to compare this with the same material whose surface has been modified with a C(18) phase, in order to use them for preconcentration/extraction of proteins. The performance of the silica-based monolithic rod was evaluated using eight proteins; insulin, cytochrome C, lysozyme, myoglobin, β-lactoglobulin, ovalbumin, hemoglobin, and bovine serum albumin at a concentration of 60 μM. The results show that recovery of the proteins was achieved by both columns with variable yields; however, the C(18) modified silica monolith gave higher recoveries (92.7 to 109.7%) than the non-modified silica monolith (25.5 to 97.9%). Both silica monoliths can be used with very low back pressure indicating a promising approach for future fabrication of the silica monolith inside a microfluidic device for the extraction of proteins from biological media.

  14. Removing Dross From Molten Solder

    Science.gov (United States)

    Webb, Winston S.

    1990-01-01

    Automatic device helps to assure good solder connections. Machine wipes dross away from area on surface of molten solder in pot. Sweeps across surface of molten solder somewhat in manner of windshield wiper. Each cycle of operation triggered by pulse from external robot. Equipment used wherever precise, automated soldering must be done to military specifications.

  15. Thermal conductivity of molten metals

    Energy Technology Data Exchange (ETDEWEB)

    Peralta-Martinez, Maria Vita

    2000-02-01

    A new instrument for the measurement of the thermal conductivity of molten metals has been designed, built and commissioned. The apparatus is based on the transient hot-wire technique and it is intended for operation over a wide range of temperatures, from ambient up to 1200 K, with an accuracy approaching 2%. In its present form the instrument operates up to 750 K. The construction of the apparatus involved four different stages, first, the design and construction of the sensor and second, the construction of an electronic system for the measurement and storage of data. The third stage was the design and instrumentation of the high temperature furnace for the melting and temperature control of the sample, and finally, an algorithm was developed for the extraction of the thermal conductivity from the raw measurement data. The sensor consists of a cylindrical platinum-wire symmetrically sandwiched between two rectangular plane sheets of alumina. The rectangular sensor is immersed in the molten metal of interest and a voltage step is applied to the ends of the platinum wire to induce heat dissipation and a consequent temperature rise which, is in part, determined by the thermal conductivity of the molten metal. The process is described by a set of partial differential equations and appropriate boundary conditions rather than an approximate analytical solution. An electronic bridge configuration was designed and constructed to perform the measurement of the resistance change of the platinum wire in the time range 20 {mu}s to 1 s. The resistance change is converted to temperature change by a suitable calibration. From these temperature measurements as a function of time the thermal conductivity of the molten metals has been deduced using the Finite Element Method for the solution of the working equations. This work has achieved its objective of improving the accuracy of the measurement of the thermal conductivity of molten metals from {+-}20% to {+-}2%. Measurements

  16. PARTICULARITIES REGARDING THE OPERATING PROCESS OF THE CUTTING AND EXTRACTION DEVICE IN THE CANDU HORIZONTAL FUEL CHANNELS PRESSURE TUBE DECOMMISSIONING PART I: MOVEMENT AND FIXING DEVICE INSIDE THE PRESSURE TUBE

    Directory of Open Access Journals (Sweden)

    Constantin POPESCU

    2016-05-01

    Full Text Available This paper presents some details of operation process for a Cutting and Extraction Device (CED in order to achieve the decommissioning of the horizontal fuel channels pressure tube in the CANDU 6 nuclear reactor. The most important characteristic of the Cutting and Extraction Device (CED is his capability of totally operator’s protection against the nuclear radiation during pressure tube decommissioning. The movement and fixing processes present few particularities due to special adopted technical solutions: train guiding-fixing modules equipped with elastic guiding rollers and fixing claws, traction modules with elastic rollers and variable pitch, also with propriety to adapt the system according to various dimensions of the tube. The Cutting and Extraction Device (CED is a train of modules equipped with special systems to be fully automated, connected with a Programmable Logic Controller (PLC and controlled by an operator panel type Human Machine Interface (HMI. All processes are monitored by video cameras. In case of error, the process is automatically stopped, the operator receiving an error message and the last sequence could be reinitialized or aborted due to safety reasons

  17. Crack characterisation using invariable feature extraction in stainless steel specimen used for absorber tubes of CSP applications via EMAT

    DEFF Research Database (Denmark)

    Cheng, Liang; Kogia, Maria; Mohimi, Abbas

    2017-01-01

    is more reliable to the tubes at high temperature through a review and the access to the absorber tubes is limited. In this paper, the crack detection and quantification for stainless steel specimen used for absorber tube using Electromagnetic Acoustic Transducers (EMATs) is presented. Through numerical......Absorber tubes are one of the most critical components of parabolic trough Concentrated Solar Plants (CSPs). Due to the high temperatures where these tubes perform at with concentration of sunlight, it is very likely for them to get damaged such as crack and mass loss etc., and lose functionality...

  18. Aluminothermic Reduction-Molten Salt Electrolysis Using Inert Anode for Oxygen and Al-Base Alloy Extraction from Lunar Soil Simulant

    Science.gov (United States)

    Xie, Kaiyu; Shi, Zhongning; Xu, Junli; Hu, Xianwei; Gao, Bingliang; Wang, Zhaowen

    2017-10-01

    Aluminothermic reduction-electrolysis using an inert anode process is proposed to extract oxygen and metals from Minnesota Lunar Simulant-1 (MLS-1). Effective aluminothermic reduction between dissolved MLS-1 and dissolved metal aluminum was achieved in cryolite salt media. The product phases obtained by aluminothermic reduction at 980°C for 4 h were Al, Si, and Al5FeSi, while the chemical components were 79.71 mass% aluminum, 12.03 mass% silicon, 5.91 mass% iron, and 2.35 mass% titanium. The cryolite salt containing Al2O3 was subsequently electrolyzed with Fe0.58-Ni0.42 inert anode at 960°C for 4 h. Oxygen was evolved at the anode with an anodic current efficiency of 78.28%. The results demonstrate that this two-step process is remarkably feasible for the extraterrestrial extraction of oxygen and metals. This process will help expand the existing in situ resource utilization methods.

  19. Release properties of UC sub x and molten U targets

    CERN Document Server

    Roussière, B; Sauvage, J; Bajeat, O; Barre, N; Clapier, F; Cottereau, E; Donzaud, C; Ducourtieux, M; Essabaa, S; Guillemaud-Müller, D; Lau, C; Lefort, H; Liang, C F; Le Blanc, F; Müller, A C; Obert, J; Pauwels, N; Potier, J C; Pougheon, F; Proust, J; Sorlin, O; Verney, D; Wojtasiewicz, A

    2002-01-01

    The release properties of UC sub x and molten U thick targets associated with a Nier-Bernas ion source have been studied. Two experimental methods are used to extract the release time. Results are presented and discussed for Kr, Cd, I and Xe.

  20. Release properties of UC$_x$ and molten U targets

    CERN Document Server

    Roussière, B; Sauvage, J; Bajeat, O; Barre, N; Clapier, F; Cottereau, E; Donzaud, C; Ducourtieux, M; Essabaa, S; Guillemaud-Müller, D; Lau, C; Lefort, H; Liang, C F; Le Blanc, F; Müller, A C; Obert, J; Pauwels, N; Potier, J C; Pougheon, F; Proust, J; Sorlin, O; Verney, D; Wojtasiewicz, A

    2002-01-01

    The release properties of UC$_x$ and molten U thick targets associated with a Nier- Bernas ion source have been studied. Two experimental methods are used to extract the release time. Results are presented and discussed for Kr, Cd, I and Xe.

  1. Crack characterisation using invariable feature extraction in stainless steel specimen used for absorber tubes of CSP applications via EMAT

    DEFF Research Database (Denmark)

    Kappatos, Vasileios; Cheng, Liang; Kogia, Maria

    2017-01-01

    Absorber tubes are one of the most critical components of parabolic trough Concentrated Solar Plants (CSPs). Due to the high temperatures where these tubes perform at with concentration of sunlight, it is very likely for them to get damaged such as crack and mass loss etc., and lose functionality...

  2. Molten metal injector system and method

    Energy Technology Data Exchange (ETDEWEB)

    Meyer, Thomas N. (Murrysville, PA); Kinosz, Michael J. (Apollo, PA); Bigler, Nicolas (Morin Heights, CA); Arnaud, Guy (Riviere-Beaudette, CA)

    2003-04-01

    Disclosed is a molten metal injector system including a holder furnace, a casting mold supported above the holder furnace, and a molten metal injector supported from a bottom side of the mold. The holder furnace contains a supply of molten metal having a metal oxide film surface. The bottom side of the mold faces the holder furnace. The mold defines a mold cavity for receiving the molten metal from the holder furnace. The injector projects into the holder furnace and is in fluid communication with the mold cavity. The injector includes a piston positioned within a piston cavity defined by a cylinder for pumping the molten metal upward from the holder furnace and injecting the molten metal into the mold cavity under pressure. The piston and cylinder are at least partially submerged in the molten metal when the holder furnace contains the molten metal. The cylinder further includes a molten metal intake for receiving the molten metal into the piston cavity. The molten metal intake is located below the metal oxide film surface of the molten metal when the holder furnace contains the molten metal. A method of injecting molten metal into a mold cavity of a casting mold is also disclosed.

  3. In-tube electro-membrane extraction with a sub-microliter organic solvent consumption as an efficient technique for synthetic food dyes determination in foodstuff samples.

    Science.gov (United States)

    Bazregar, Mohammad; Rajabi, Maryam; Yamini, Yadollah; Asghari, Alireza; Abdossalami asl, Yousef

    2015-09-04

    A simple and efficient extraction technique with a sub-microliter organic solvent consumption termed as in-tube electro-membrane extraction (IEME) is introduced. This method is based upon the electro-kinetic migration of ionized compounds by the application of an electrical potential difference. For this purpose, a thin polypropylene (PP) sheet placed inside a tube acts as a support for the membrane solvent, and 30μL of an aqueous acceptor solution is separated by this solvent from 1.2mL of an aqueous donor solution. This method yielded high extraction recoveries (63-81%), and the consumption of the organic solvent used was only 0.5μL. By performing this method, the purification is high, and the utilization of the organic solvent, used as a mediator, is very simple and repeatable. The proposed method was evaluated by extraction of four synthetic food dyes (Amaranth, Ponceau 4R, Allura Red, and Carmoisine) as the model analytes. Optimization of variables affecting the method was carried out in order to achieve the best extraction efficiency. These variables were the type of membrane solvent, applied extraction voltage, extraction time, pH range, and concentration of salt added. Under the optimized conditions, IEME-HPLC-UV provided a good linearity in the range of 1.00-800ngmL(-1), low limits of detection (0.3-1ngmL(-1)), and good extraction repeatabilities (RSDs below 5.2%, n=5). It seems that this design is a proper one for the automation of the method. Also the consumption of the organic solvent in a sub-microliter scale, and its simplicity, high efficiency, and high purification can help one getting closer to the objectives of the green chemistry.

  4. Resistance of Nanostructured Environmental Barrier Coatings to the Movement of Molten Salts

    Science.gov (United States)

    Rao, S.; Frederick, L.; McDonald, A.

    2012-09-01

    Corrosion of components in a recovery boiler is a major problem faced by the pulp and paper industry. The superheater tubes become severely corroded due to the presence of sulfidic gases in the boiler and molten salts which are deposited on the surface of the tubes. As a result, the boiler must be decommissioned for expensive maintenance and repairs. Yttria-stabilized zirconia (YSZ) coatings have been shown to provide corrosion resistance when applied on gas turbines operating at high temperatures. Air plasma-sprayed YSZ environmental barrier coatings on Type 309 stainless steel were exposed to three different corrosive environments: Test A—600 °C, salt vapors, flue gases, 168 h; Test B—600 °C, molten salt, air, 168 h; and Test C—600 °C, molten salt, flue gases, 168 h. Two different types of YSZ coatings—conventional YSZ and nanostructured YSZ—were tested to study their resistance to corrosion and molten salt penetration. The performances of both types of coatings were evaluated, and a comparative study was conducted. It was found that the nanostructured YSZ samples protected the stainless steel substrate better than their conventional counterparts. This superior performance was attributed to the presence of semi-molten nano-agglomerates present in the coating microstructure, which acted as collection points for the penetrating molten salts.

  5. Study of aluminium and neodymium co-extraction in molten fluoride media by electrochemical reduction; Etude de la co-extraction de l'aluminium et du neodyme en milieux fluorures fondus par reduction electrochimique

    Energy Technology Data Exchange (ETDEWEB)

    Gibilaro, M.; Massot, L.; Chamelot, P.; Taxil, P. [Universite Paul Sabatier, Lab. de Genie Chimique UMR 5503, Dept. Procedes Electrochimiques, 31 - Toulouse (France)

    2007-07-01

    The aim of this work is to identify and characterize the alloys formed as well as the feasibility of this electrochemical co-extraction in a LiF-CaF{sub 2} (79-21 % mol.) medium in a temperature range between 840 and 960 C. At first, the study of the alloys is carried out at different temperatures from cyclic voltametry techniques, squared wave voltametry as well as by tungsten imposed potential electrolyses (metal which is inert towards the two elements to be extracted). The potential relaxation technique is used for the determination of the standard enthalpy of formation of the Al-Nd alloys. The obtained alloys are characterized by scanning electron microscopy with probe analysis. The encouraging results of the preliminary extraction experiments led under tungsten in presence of weak quantities of neodymium allow to consider the validation of the process. (O.M.)

  6. Silica supported Fe(3)O(4) magnetic nanoparticles for magnetic solid-phase extraction and magnetic in-tube solid-phase microextraction: application to organophosphorous compounds.

    Science.gov (United States)

    Moliner-Martinez, Y; Vitta, Yosmery; Prima-Garcia, Helena; González-Fuenzalida, R A; Ribera, Antonio; Campíns-Falcó, P; Coronado, Eugenio

    2014-03-01

    This work demonstrates the application of silica supported Fe3O4 nanoparticles as sorbent phase for magnetic solid-phase extraction (MSPE) and magnetic on-line in-tube solid-phase microextraction (Magnetic-IT-SPME) combined with capillary liquid chromatography-diode array detection (CapLC-DAD) to determine organophosphorous compounds (OPs) at trace level. In MSPE, magnetism is used as separation tool while in Magnetic-IT-SPME, the application of an external magnetic field gave rise to a significant improvement of the adsorption of OPs on the sorbent phase. Extraction efficiency, analysis time, reproducibility and sensitivity have been compared. This work showed that Magnetic-IT-SPME can be extended to OPs with successful results in terms of simplicity, speed, extraction efficiency and limit of detection. Finally, wastewater samples were analysed to determine OPs at nanograms per litre.

  7. Ear Tubes

    Science.gov (United States)

    ... ENTCareers Marketplace Find an ENT Doctor Near You Ear Tubes Ear Tubes Patient Health Information News media ... and throat specialist) may be considered. What are ear tubes? Ear tubes are tiny cylinders placed through ...

  8. Stability of Molten Core Materials

    Energy Technology Data Exchange (ETDEWEB)

    Layne Pincock; Wendell Hintze

    2013-01-01

    The purpose of this report is to document a literature and data search for data and information pertaining to the stability of nuclear reactor molten core materials. This includes data and analysis from TMI-2 fuel and INL’s LOFT (Loss of Fluid Test) reactor project and other sources.

  9. Evaluation of Superparamagnetic Silica Nanoparticles for Extraction of Triazines in Magnetic in-Tube Solid Phase Microextraction Coupled to Capillary Liquid Chromatography

    Science.gov (United States)

    González-Fuenzalida, R. A.; Moliner-Martínez, Y.; Prima-Garcia, Helena; Ribera, Antonio; Campins-Falcó, P.; Zaragozá, Ramon J.

    2014-01-01

    The use of magnetic nanomaterials for analytical applications has increased in the recent years. In particular, magnetic nanomaterials have shown great potential as adsorbent phase in several extraction procedures due to the significant advantages over the conventional methods. In the present work, the influence of magnetic forces over the extraction efficiency of triazines using superparamagnetic silica nanoparticles (NPs) in magnetic in tube solid phase microextraction (Magnetic-IT-SPME) coupled to CapLC has been evaluated. Atrazine, terbutylazine and simazine has been selected as target analytes. The superparamagnetic silica nanomaterial (SiO2-Fe3O4) deposited onto the surface of a capillary column gave rise to a magnetic extraction phase for IT-SPME that provided a enhancemment of the extraction efficiency for triazines. This improvement is based on two phenomena, the superparamegnetic behavior of Fe3O4 NPs and the diamagnetic repulsions that take place in a microfluidic device such a capillary column. A systematic study of analytes adsorption and desorption was conducted as function of the magnetic field and the relationship with triazines magnetic susceptibility. The positive influence of magnetism on the extraction procedure was demonstrated. The analytical characteristics of the optimized procedure were established and the method was applied to the determination of the target analytes in water samples with satisfactory results. When coupling Magnetic-IT-SPME with CapLC, improved adsorption efficiencies (60%–63%) were achieved compared with conventional adsorption materials (0.8%–3%).

  10. Trace Analysis in End-Exhaled Air Using Direct Solvent Extraction in Gas Sampling Tubes: Tetrachloroethene in Workers as an Example

    Directory of Open Access Journals (Sweden)

    Chris-Elmo Ziener

    2014-01-01

    Full Text Available Simple and cost-effective analytical methods are required to overcome the barriers preventing the use of exhaled air in routine occupational biological monitoring. Against this background, a new method is proposed that simplifies the automation and calibration of the analytical measurements. End-exhaled air is sampled using valveless gas sampling tubes made of glass. Gaseous analytes are transferred to a liquid phase using a microscale solvent extraction performed directly inside the gas sampling tubes. The liquid extracts are analysed using a gas chromatograph equipped, as usual, with a liquid autosampler, and liquid standards are used for calibration. For demonstration purposes, the method’s concept was applied to the determination of tetrachloroethene in end-exhaled air, which is a biomarker for occupational tetrachloroethene exposure. The method’s performance was investigated in the concentration range 2 to 20 μg tetrachloroethene/L, which corresponds to today’s exposure levels. The calibration curve was linear, and the intra-assay repeatability and recovery rate were sufficient. Analysis of real samples from dry-cleaning workers occupationally exposed to tetrachloroethene and from nonexposed subjects demonstrated the method’s utility. In the case of tetrachloroethene, the method can be deployed quickly, requires no previous experiences in gas analysis, provides sufficient analytical reliability, and addresses typical end-exhaled air concentrations from exposed workers.

  11. Molten fluorides for nuclear applications

    Directory of Open Access Journals (Sweden)

    Sylvie. Delpech

    2010-12-01

    Full Text Available The importance of pyrochemistry is being increasingly acknowledged and becomes unavoidable in the nuclear field. Molten salts may be used for fuel processing and spent fuel recycling, for heat transfer, as a homogeneous fuel and as a breeder material in fusion systems. Fluorides that are stable at high temperature and under high neutron flux are especially promising. Analysis of several field cases reveals that corrosion in molten fluorides is essentially due to the oxidation of metals by uranium fluoride and/or oxidizing impurities. The thermodynamics of this process are discussed with an emphasis on understanding the mass transfer in the systems, selecting appropriate metallic materials and designing effective purification methods.

  12. Molten carbonate fuel cell matrices

    Science.gov (United States)

    Vogel, Wolfgang M.; Smith, Stanley W.

    1985-04-16

    A molten carbonate fuel cell including a cathode electrode of electrically conducting or semiconducting lanthanum containing material and an electrolyte containing matrix of an electrically insulating lanthanum perovskite. In addition, in an embodiment where the cathode electrode is LaMnO.sub.3, the matrix may include LaAlO.sub.3 or a lithium containing material such as LiAlO.sub.2 or Li.sub.2 TiO.sub.3.

  13. Development of a Minichannel Compact Primary Heat Exchanger for a Molten Salt Reactor

    OpenAIRE

    Lippy, Matthew Stephen

    2011-01-01

    The first Molten Salt Reactor (MSR) was designed and tested at Oak Ridge National Laboratory (ORNL) in the 1960â s, but recent technological advancements now allow for new components, such as heat exchangers, to be created for the next generation of MSRâ s and molten salt-cooled reactors. The primary (fuel salt-to-secondary salt) heat exchanger (PHX) design is shown here to make dramatic improvements over traditional shell-and-tube heat exchangers when changed to a compact heat exchanger de...

  14. Multiple automated headspace in-tube extraction for the accurate analysis of relevant wine aroma compounds and for the estimation of their relative liquid-gas transfer rates.

    Science.gov (United States)

    Zapata, Julián; Lopez, Ricardo; Herrero, Paula; Ferreira, Vicente

    2012-11-30

    An automated headspace in-tube extraction (ITEX) method combined with multiple headspace extraction (MHE) has been developed to provide simultaneously information about the accurate wine content in 20 relevant aroma compounds and about their relative transfer rates to the headspace and hence about the relative strength of their interactions with the matrix. In the method, 5 μL (for alcohols, acetates and carbonyl alcohols) or 200 μL (for ethyl esters) of wine sample were introduced in a 2 mL vial, heated at 35°C and extracted with 32 (for alcohols, acetates and carbonyl alcohols) or 16 (for ethyl esters) 0.5 mL pumping strokes in four consecutive extraction and analysis cycles. The application of the classical theory of Multiple Extractions makes it possible to obtain a highly reliable estimate of the total amount of volatile compound present in the sample and a second parameter, β, which is simply the proportion of volatile not transferred to the trap in one extraction cycle, but that seems to be a reliable indicator of the actual volatility of the compound in that particular wine. A study with 20 wines of different types and 1 synthetic sample has revealed the existence of significant differences in the relative volatility of 15 out of 20 odorants. Differences are particularly intense for acetaldehyde and other carbonyls, but are also notable for alcohols and long chain fatty acid ethyl esters. It is expected that these differences, linked likely to sulphur dioxide and some unknown specific compositional aspects of the wine matrix, can be responsible for relevant sensory changes, and may even be the cause explaining why the same aroma composition can produce different aroma perceptions in two different wines. Copyright © 2012 Elsevier B.V. All rights reserved.

  15. Processing method for molten salt waste

    Energy Technology Data Exchange (ETDEWEB)

    Ito, Shuichi; Sawa, Toshio; Hoshikawa, Tadahiro; Suzuoki, Akira

    1999-01-06

    The present invention concerns a processing method for selectively adsorbing and removing radioactive metal ingredients contained in high temperature molten salts by an inorganic ion exchanger and separating radioactive metal ingredients from the molten salts as high level radioactive wastes upon reprocessing of spent nuclear fuels by using molten salts. The molten salts occluded in the inorganic ion exchanger are desorbed with highly purified water. Successively, saturation adsorbed radioactive metal ingredients are desorbed by an aqueous solution of alkali metal salt or an aqueous solution of alkaline earth metal salt. The desorbed molten salts and radioactive metal ingredients are formed into at least two kinds of radioactive waste solidification materials depending on each of radioactivity level. As the inorganic ion exchanger, at least one of aluminosilicate and hydroxides is used. Then, molten salt wastes generated upon a dry-type reprocessing can be processed as a stable borosilicate glass solidification material or as a similar homogeneous solid material. (T.M.)

  16. Electrochemistry and Electrochemical Methodology in Molten Salts.

    Science.gov (United States)

    1980-09-01

    similar conditions. A manuscript based on this work has been published in the Journal of the Electrochemical Society (34). 2) Melt and co-solvent As...Temperature Molten Salt," In "Proceedings of the 2nd International Symposium on Molten Salts," 3. Braunstein, Ed., published by The Electrochemical Society , in...Jones and L. G. Boxall, "Electrochemical Studies in Molten Chloroaluminates," Symposium on Fused Salt Tech- nology, Electrochemical Society Meeting

  17. The molten glass sewing machine

    Science.gov (United States)

    Brun, P.-T.; Inamura, Chikara; Lizardo, Daniel; Franchin, Giorgia; Stern, Michael; Houk, Peter; Oxman, Neri

    2017-04-01

    We present a fluid-instability-based approach for digitally fabricating geometrically complex uniformly sized structures in molten glass. Formed by mathematically defined and physically characterized instability patterns, such structures are produced via the additive manufacturing of optically transparent glass, and result from the coiling of an extruded glass thread. We propose a minimal geometrical model-and a methodology-to reliably control the morphology of patterns, so that these building blocks can be assembled into larger structures with tailored functionally and optically tunable properties. This article is part of the themed issue 'Patterning through instabilities in complex media: theory and applications'.

  18. Potentiometric Sensor for Real-Time Monitoring of Multivalent Ion Concentrations in Molten Salt

    Energy Technology Data Exchange (ETDEWEB)

    Peter A. Zink; Jan-Fong Jue; Brenda E. Serrano; Guy L. Fredrickson; Ben F. Cowan; Steven D. Herrmann; Shelly X. Li

    2010-07-01

    Electrorefining of spent metallic nuclear fuel in high temperature molten salt systems is a core technology in pyroprocessing, which in turn plays a critical role in the development of advanced fuel cycle technologies. In electrorefining, spent nuclear fuel is treated electrochemically in order to effect separations between uranium, noble metals, and active metals, which include the transuranics. The accumulation of active metals in a lithium chloride-potassium chloride (LiCl-KCl) eutectic molten salt electrolyte occurs at the expense of the UCl3-oxidant concentration in the electrolyte, which must be periodically replenished. Our interests lie with the accumulation of active metals in the molten salt electrolyte. The real-time monitoring of actinide concentrations in the molten salt electrolyte is highly desirable for controlling electrochemical operations and assuring materials control and accountancy. However, real-time monitoring is not possible with current methods for sampling and chemical analysis. A new solid-state electrochemical sensor is being developed for real-time monitoring of actinide ion concentrations in a molten salt electrorefiner. The ultimate function of the sensor is to monitor plutonium concentrations during electrorefining operations, but in this work gadolinium was employed as a surrogate material for plutonium. In a parametric study, polycrystalline sodium beta double-prime alumina (Na-ß?-alumina) discs and tubes were subject to vapor-phase exchange with gadolinium ions (Gd3+) using a gadolinium chloride salt (GdCl3) as a precursor to produce gadolinium beta double-prime alumina (Gd-ß?-alumina) samples. Electrochemical impedance spectroscopy and microstructural analysis were performed on the ion-exchanged discs to determine the relationship between ion exchange and Gd3+ ion conductivity. The ion-exchanged tubes were configured as potentiometric sensors in order to monitor real-time Gd3+ ion concentrations in mixtures of gadolinium

  19. Potentiometric Sensor for Real-Time Monitoring of Multivalent Ion Concentrations in Molten Salt

    Energy Technology Data Exchange (ETDEWEB)

    Peter A. Zink; Jan-Fong Jue; Brenda E. Serrano; Guy L. Fredrickson; Ben F. Cowan; Steven D. Herrmann; Shelly X. Li

    2010-07-01

    Electrorefining of spent metallic nuclear fuel in high temperature molten salt systems is a core technology in pyroprocessing, which in turn plays a critical role in the development of advanced fuel cycle technologies. In electrorefining, spent nuclear fuel is treated electrochemically in order to effect separations between uranium, noble metals, and active metals, which include the transuranics. The accumulation of active metals in a lithium chloride-potassium chloride (LiCl-KCl) eutectic molten salt electrolyte occurs at the expense of the UCl3-oxidant concentration in the electrolyte, which must be periodically replenished. Our interests lie with the accumulation of active metals in the molten salt electrolyte. The real-time monitoring of actinide concentrations in the molten salt electrolyte is highly desirable for controlling electrochemical operations and assuring materials control and accountancy. However, real-time monitoring is not possible with current methods for sampling and chemical analysis. A new solid-state electrochemical sensor is being developed for real-time monitoring of actinide ion concentrations in a molten salt electrorefiner. The ultimate function of the sensor is to monitor plutonium concentrations during electrorefining operations, but in this work gadolinium was employed as a surrogate material for plutonium. In a parametric study, polycrystalline sodium beta double-prime alumina (Na-ß?-alumina) discs and tubes were subject to vapor-phase exchange with gadolinium ions (Gd3+) using a gadolinium chloride salt (GdCl3) as a precursor to produce gadolinium beta double-prime alumina (Gd-ß?-alumina) samples. Electrochemical impedance spectroscopy and microstructural analysis were performed on the ion-exchanged discs to determine the relationship between ion exchange and Gd3+ ion conductivity. The ion-exchanged tubes were configured as potentiometric sensors in order to monitor real-time Gd3+ ion concentrations in mixtures of gadolinium

  20. Mechanism of removing inclusions from molten aluminum by stirring active molten flux

    Institute of Scientific and Technical Information of China (English)

    周鸣; 李克; 孙宝德; 疏达; 倪红军; 王俊; 张佼

    2003-01-01

    Removal of inclusions from industrial pure molten aluminum(A01) by stirring active molten flux wasstudied. Wettability of nonmetallic inclusions in the molten aluminum was worse than that in active molten flux. Ac-cording to the surface renewal model, the inclusions were easily transferred into molten active flux from fine alumi-num droplets and then reacted chemically when molten aluminum was dispersed into fine aluminum droplets in stir-ring active molten flux. Tensile tests show that tensile strength of purified tensile sample(as-cast) increases by8.59%. SEM photographs show that the fracture cracks of purified tensile sample are homogeneous, and the dim-ples are small and homogeneous. From metallographs and statistic results of Leco analysis software, it is found thatthe quantities and sizes of the inclusions in purified sample are obviously fewer and smaller than in unpurified tensilesample(as-cast).

  1. Metal Production by Molten Salt Electrolysis

    DEFF Research Database (Denmark)

    Grjotheim, K.; Kvande, H.; Qingfeng, Li

    Chemistry and electrochemistry of molten salts are reviewed. Technological aspects of electrolytic production of aluminium, magnesium, and other metals are comprehensively surveyed.......Chemistry and electrochemistry of molten salts are reviewed. Technological aspects of electrolytic production of aluminium, magnesium, and other metals are comprehensively surveyed....

  2. Metal Production by Molten Salt Electrolysis

    DEFF Research Database (Denmark)

    Grjotheim, K.; Kvande, H.; Qingfeng, Li

    Chemistry and electrochemistry of molten salts are reviewed. Technological aspects of electrolytic production of aluminium, magnesium, and other metals are comprehensively surveyed.......Chemistry and electrochemistry of molten salts are reviewed. Technological aspects of electrolytic production of aluminium, magnesium, and other metals are comprehensively surveyed....

  3. Purification technology of molten aluminum

    Institute of Scientific and Technical Information of China (English)

    孙宝德; 丁文江; 疏达; 周尧和

    2004-01-01

    Various purification methods were explored to eliminate the dissolved hydrogen and nonmetallic inclusions from molten aluminum alloys. A novel rotating impeller head with self-oscillation nozzles or an electromagnetic valve in the gas circuit was used to produce pulse gas currents for the rotary impeller degassing method. Water simulation results show that the size of gas bubbles can be decreased by 10%-20% as compared with the constant gas current mode. By coating ceramic filters or particles with active flux or enamels, composite filters were used to filter the scrap A356 alloy and pure aluminum. Experimental results demonstrate that better filtration efficiency and operation performance can be obtained. Based on numerical calculations, the separation efficiency of inclusions by high frequency magnetic field can be significantly improved by using a hollow cylinder-like separator or utilizing the effects of secondary flow of the melt in a square separator. A multi-stage and multi-media purification platform based on these methods was designed and applied in on-line processing of molten aluminum alloys. Mechanical properties of the processed scrap A356 alloy are greatly improved by the composite purification.

  4. Advances in electroanalysis, sensing and monitoring in molten salts.

    Science.gov (United States)

    Corrigan, Damion K; Elliott, Justin P; Blair, Ewen O; Reeves, Simon J; Schmüser, Ilka; Walton, Anthony J; Mount, Andrew R

    2016-08-15

    Microelectrodes have a number of advantages over macroelectrodes for quantitative electroanalysis and monitoring, including reduced iR drop, a high signal-to-noise ratio and reduced sensitivity to convection. Their use in molten salts has been generally precluded by the combined materials challenges of stresses associated with thermal cycling and physical and corrosive chemical degradation at the relatively high temperatures involved. We have shown that microfabrication, employing high precision photolithographic patterning in combination with the controlled deposition of materials, can be used to successfully address these challenges. The resulting molten salt compatible microelectrodes (MSMs) enable prolonged quantitative microelectrode measurements in molten salts (MSs). This paper reports the fabrication of novel MSM disc electrodes, chosen because they have an established ambient analytical response. It includes a detailed set of electrochemical characterisation studies which demonstrate both their enhanced capability over macroelectrodes and over commercial glass pulled microelectrodes, and their ability to extract quantitative electroanalytical information from MS systems. MSM measurements are then used to demonstrate their potential for shedding new light on the fundamental properties of, and processes in, MSs, such as mass transport, charge transfer reaction rates and the selective plating/stripping and alloying reactions of liquid Bi and other metals; this will underpin the development of enhanced MS industrial processes, including pyrochemical spent nuclear fuel reprocessing.

  5. Helium-cooled molten-salt fusion breeder

    Energy Technology Data Exchange (ETDEWEB)

    Moir, R.W.; Lee, J.D.; Fulton, F.J.; Huegel, F.; Neef, W.S. Jr.; Sherwood, A.E.; Berwald, D.H.; Whitley, R.H.; Wong, C.P.C.; Devan, J.H.

    1984-12-01

    We present a new conceptual design for a fusion reactor blanket that is intended to produce fissile material for fission power plants. Fast fission is suppressed by using beryllium instead of uranium to multiply neutrons. Thermal fission is suppressed by minimizing the fissile inventory. The molten-salt breeding medium (LiF + BeF/sub 2/ + ThF/sub 4/) is circulated through the blanket and to the on-line processing system where /sup 233/U and tritium are continuously removed. Helium cools the blanket and the austenitic steel tubes that contain the molten salt. Austenitic steel was chosen because of its ease of fabrication, adequate radiation-damage lifetime, and low corrosion by molten salt. We estimate that a breeder having 3000 MW of fusion power will produce 6500 kg of /sup 233/U per year. This amount is enough to provide makeup for 20 GWe of light-water reactors per year or twice that many high-temperature gas-cooled reactors or Canadian heavy-water reactors. Safety is enhanced because the afterheat is low and blanket materials do not react with air or water. The fusion breeder based on a pre-MARS tandem mirror is estimated to cost $4.9B or 2.35 times a light-water reactor of the same power. The estimated cost of the /sup 233/U produced is $40/g for fusion plants costing 2.35 times that of a light-water reactor if utility owned or $16/g if government owned.

  6. Continuous replenishment of molten semiconductor in a Czochralski-process, single-crystal-growing furnace

    Science.gov (United States)

    Fiegl, George (Inventor); Torbet, Walter (Inventor)

    1981-01-01

    A replenishment crucible is mounted adjacent the usual drawing crucible, from which a monocrystalline boule is drawn according to the Czochralski method. A siphon tube for molten semiconductor transfer extends from the replenishment crucible to the drawing crucible. Each crucible is enclosed within its own hermetic shell and is provided with its own heater. The siphon tube is initially filled with molten semiconductor by raising the inert atmospheric pressure in the shell surrounding the replenishment crucible above that surrounding the drawing crucible. Thereafter, adjustment of the level of molten semiconductor in the drawing crucible may be achieved by adjusting the level in either crucible, since the siphon tube will establish the same level in both crucibles. For continuous processing, solid semiconductor may be added to and melted in the replenishment crucible during the process of drawing crystals from the drawing crucible. A constant liquid level of melted semiconductor is maintained in the system by an optical monitoring device and any of several electromechanical controls of the rate of replenishment or crucible height.

  7. Corrosion of metals in molten salts

    Energy Technology Data Exchange (ETDEWEB)

    Vossen, J.P.T.

    1991-05-15

    Part 1 of this report describes the results of a literature study on the corrosion behavior of metals in molten carbonates. The results form the basis for a doctorate study related to improving the durability of metal separator plates for molten carbonate fuel cells. To gain a better understanding also the literature on corrosion in molten sulfates has been reviewed, the results of which are summarized in Part 2 of this report. For each part a separate abstract has been prepared. 83 figs., 23 tabs., 1 app., 78 refs.

  8. Tracheostomy tubes.

    Science.gov (United States)

    Hess, Dean R; Altobelli, Neila P

    2014-06-01

    Tracheostomy tubes are used to administer positive-pressure ventilation, to provide a patent airway, and to provide access to the lower respiratory tract for airway clearance. They are available in a variety of sizes and styles from several manufacturers. The dimensions of tracheostomy tubes are given by their inner diameter, outer diameter, length, and curvature. Differences in dimensions between tubes with the same inner diameter from different manufacturers are not commonly appreciated but may have important clinical implications. Tracheostomy tubes can be cuffed or uncuffed and may be fenestrated. Some tracheostomy tubes are designed with an inner cannula. It is important for clinicians caring for patients with a tracheostomy tube to appreciate the nuances of various tracheostomy tube designs and to select a tube that appropriately fits the patient. The optimal frequency of changing a chronic tracheostomy tube is controversial. Specialized teams may be useful in managing patients with a tracheostomy. Speech can be facilitated with a speaking valve in patients with a tracheostomy tube who are breathing spontaneously. In mechanically ventilated patients with a tracheostomy, a talking tracheostomy tube, a deflated cuff technique with a speaking valve, or a deflated cuff technique without a speaking valve can be used to facilitate speech. Copyright © 2014 by Daedalus Enterprises.

  9. Effective extraction of triazines from environmental water samples using magnetism-enhanced monolith-based in-tube solid phase microextraction.

    Science.gov (United States)

    Mei, Meng; Huang, Xiaojia; Yang, Xiaodong; Luo, Qing

    2016-09-21

    This article reports on the effective extraction of triazines from environmental water samples using magnetism-enhanced monolith-based in-tube solid phase microextraction (ME-MB/IT-SPME). Firstly, monolithic poly (octyl methacrylate-co-ethyleneglycol dimethacrylate) capillary column doped with magnetic nanoparticles was synthesized inside a fused silica. After that, the monolithic capillary column was placed inside a magnetic coil that allowed the exertion of a variable magnetic field during adsorption and desorption steps. The effects of intensity of magnetic field, adsorption and desorption flow rate, volume of sample and desorption solvent, pH value and ionic strength in sample matrix on the performance of ME-MB/IT-SPME for triazines were investigated in details. Under the optimized conditions, the developed ME-MB/IT-SPME showed satisfactory quantitative extraction efficiencies of the target analytes between 64.8% and 99.7%. At the same time, the ME-MB/IT-SPME was combined with high-performance liquid chromatography with diode array detection to detect six triazines in water samples. The limits of detection (S/N = 3) and limits of quantification (S/N = 10) were in the ranges of 0.074-0.23 μg/L and 0.24-0.68 μg/L, respectively. The precision of the proposed method was evaluated in terms of intra- and inter-assay variability calculated as relative standard deviation, and it was found that the values were all below 10%. Finally, the developed method was successfully applied for environmental water samples such as farmland, lake and river water with spiked recoveries in the range of 70.7-119%.

  10. Molten salts processes and generic simulation

    Energy Technology Data Exchange (ETDEWEB)

    Ogawa, Toru; Minato, Kazuo [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

    2001-12-01

    Development of dry separation process (pyrochemical process) using molten salts for the application of spent-nuclear fuel reprocessing requires a rather complete fundamental database as well as process simulation technique with wide applicability. The present report concerns recent progress and problems in this field taking behaviors of co-electrodeposition of UO{sub 2} and PuO{sub 2} in molten salts as an example, and using analytical simulation of local equilibrium combined with generic diffusion. (S. Ohno)

  11. Structure of molten titanium dioxide

    Energy Technology Data Exchange (ETDEWEB)

    Alderman, O. L. G.; Skinner, L. B.; Benmore, C. J.; Tamalonis, A.; Weber, J. K. R.

    2014-09-01

    The x-ray structure factor of molten TiO2 has been measured for the first time, enabled by the use of aerodynamic levitation and laser beam heating, to a temperature of T = 2250(30) K. Ti-O coordination number in the melt is close to nTiO = 5.0(2), with modal Ti-O bond length rTiO = 1.881(5) Å, both values being significantly smaller than for the high temperature stable Rutile crystal structure (nTiO = 6.0, rTiO = 1.959 Å). The structural differences between melt and crystal are qualitatively similar to those for alumina, which is rationalized in terms of the similar field strengths of Ti4+ and Al3+. The diffraction data are used to generate physically and chemically reasonable structural models, which are then compared to the predictions based on various classical molecular dynamics (MD) potentials. New interatomic potentials, suitable for modelling molten TiO2, are introduced, given the inability of existing MD models to reproduce the diffraction data. These new potentials have the additional great advantage of being able to predict the density and thermal expansion of the melt, as well as solid amorphous TiO2, in agreement with published results. This is of critical importance given the strong correlation between density and structural parameters such as nTiO. The large thermal expansion of the melt is associated with weakly temperature dependent structural changes, whereby simulations show that nTiO = 5.85(2) – (3.0(1) x 10-4 )T (K, 2.75 Å cut-off). The TiO2 liquid is structurally analogous to the geophysically relevant high pressure liquid silica system at around 27 GPa. We argue that the predominance of 5-fold polyhedra in the melt implies the existence of as yet undiscovered TiO2 polymorphs, based on lowerthan-octahedral coordination numbers, which are likely to be metastable under ambient conditions. Given the industrial importance of titanium oxides, experimental and computational searches for such polymorphs are well warranted.

  12. Magnetarc Welding - peculiarities of joining thin wall tubes

    OpenAIRE

    2010-01-01

    The paper presents the MAGNETARC welding of thin tubes achieved with an original longitudinal magnetization system, designed to assure the magnetic flux concentration on tube wall. Process main stages are presented, from the arc initiation until the molten metal appears, upsetting is achieved and the weld forms. Infrared thermography was used for temperature measurements and process visualization. Macro and microstructural analysis accompanies the hardness tests made on correspondingly weld...

  13. The structure of molten ZnCl2 : A new analysis of some old data

    Indian Academy of Sciences (India)

    A K Soper

    2004-07-01

    Using a recently derived method, based on empirical potential structure refinement (EPSR), the structure of molten zinc chloride (ZnCl2) is re-analysed. Contrary to the picture given in some early analyses, the results indicate that there are significant uncertainties in the extracted site–site radial distribution functions, particularly the Zn–Zn distribution. These are derived from the small weighting of this partial structure factor in the measured diffraction data and from systematic uncertainties in the original data. The simulated atom distributions are used to discuss the three-dimensional structure of this molten salt.

  14. The mystery of molten metal

    Directory of Open Access Journals (Sweden)

    Natalia Sobczak

    2010-11-01

    Full Text Available Recent advances in scientific understanding of high-temperature materials processing using novel experimental methodologies have shed light on the complex role of surface and interface phenomena. New in-situ studies on molten metal/solid ceramic interactions using a unique experimental complex at the Foundry Research Institute, Krakow, have revealed a number of unusual observations in materials processing at high temperatures. We present some such unusual observations and their explanation with reference to liquid metal processing of Al, Ni, and Ti, and their alloys in contact with oxide ceramics. In particular, we focus on the following aspects: primary oxidation of Al from residual water vapor or oxygen, capillary purification to remove surface oxide, substrate protection by CVD carbon, roughening due to spinel whisker formation, inclusions in castings due to mechanical detachment, floatation due to buoyancy forces, and segregation due to directional solidification, modification of the solid surface morphology by metal vapor ahead of the liquid, and the complication due to multi-component alloys melted in crucibles made from complex oxide-based ceramics. In the case of Ti, rapid reactions with oxides result in undesirable volumetric changes that create difficulty in casting high-quality Ti parts, particularly by investment casting. Nanoscale (e.g., colloidal coatings based on Y2O3 protect crucibles and hold ladles against such attack. Practical insights and recommendations for materials processing emerging from the fundamental studies on high-temperature interfacial phenomena have been described.

  15. Electrical conductivity anisotropy of partially molten peridotite under shear deformation

    Science.gov (United States)

    Zhang, B.; Yoshino, T.; Yamazaki, D.; Manthilake, G. M.; Katsura, T.

    2013-12-01

    Recent ocean bottom magnetotelluric investigations have revealed a high-conductivity layer (HCL) with high anisotropy characterized by higher conductivity values in the direction parallel to the plate motion beneath the southern East Pacific Rise (Evans et al., 2005) and beneath the edge of the Cocos plate at the Middle America trench offshore of Nicaragua (Naif et al., 2013). These geophysical observations have been attributed to either hydration (water) of mantle minerals or the presence of partial melt. Currently, aligned partial melt has been regarded as the most preferable candidate for explaining the conductivity anisotropy because of the implausibility of proton conduction (Yoshino et al., 2006). In this study, we report development of the conductivity anisotropy between parallel and normal to shear direction on the shear plane in partial molten peridotite as a function of time and shear strain. Starting samples were pre-synthesized partial molten peridotite, showing homogeneous melt distribution. The partially molten peridotite samples were deformed in simple shear geometry at 1 GPa and 1723 K in a DIA-type apparatus with uniaxial deformation facility. Conductivity difference between parallel and normal to shear direction reached one order, which is equivalent to that observed beneath asthenosphere. In contrast, such anisotropic behavior was not found in the melt-free samples, suggesting that development of the conductivity anisotropy was generated under shear stress. Microstructure of the deformed partial molten peridotite shows partial melt tends to preferentially locate grain boundaries parallel to shear direction, and forms continuously thin melt layer sub-parallel to the shear direction, whereas apparently isolated distribution was observed on the section perpendicular to the shear direction. The resultant melt morphology can be approximated by tube like geometry parallel to the shear direction. This observation suggests that the development of

  16. Heat Transfer and Latent Heat Storage in Inorganic Molten Salts for Concentrating Solar Power Plants

    Energy Technology Data Exchange (ETDEWEB)

    Mathur, Anoop [Terrafore Inc.

    2013-08-14

    A key technological issue facing the success of future Concentrating Solar Thermal Power (CSP) plants is creating an economical Thermal Energy Storage (TES) system. Current TES systems use either sensible heat in fluids such as oil, or molten salts, or use thermal stratification in a dual-media consisting of a solid and a heat-transfer fluid. However, utilizing the heat of fusion in inorganic molten salt mixtures in addition to sensible heat , as in a Phase change material (PCM)-based TES, can significantly increase the energy density of storage requiring less salt and smaller containers. A major issue that is preventing the commercial use of PCM-based TES is that it is difficult to discharge the latent heat stored in the PCM melt. This is because when heat is extracted, the melt solidifies onto the heat exchanger surface decreasing the heat transfer. Even a few millimeters of thickness of solid material on heat transfer surface results in a large drop in heat transfer due to the low thermal conductivity of solid PCM. Thus, to maintain the desired heat rate, the heat exchange area must be large which increases cost. This project demonstrated that the heat transfer coefficient can be increase ten-fold by using forced convection by pumping a hyper-eutectic salt mixture over specially coated heat exchanger tubes. However,only 15% of the latent heat is used against a goal of 40% resulting in a projected cost savings of only 17% against a goal of 30%. Based on the failure mode effect analysis and experience with pumping salt at near freezing point significant care must be used during operation which can increase the operating costs. Therefore, we conclude the savings are marginal to justify using this concept for PCM-TES over a two-tank TES. The report documents the specialty coatings, the composition and morphology of hypereutectic salt mixtures and the results from the experiment conducted with the active heat exchanger along with the lessons learnt during

  17. Highlights of the Salt Extraction Process

    Science.gov (United States)

    Abbasalizadeh, Aida; Seetharaman, Seshadri; Teng, Lidong; Sridhar, Seetharaman; Grinder, Olle; Izumi, Yukari; Barati, Mansoor

    2013-11-01

    This article presents the salient features of a new process for the recovery of metal values from secondary sources and waste materials such as slag and flue dusts. It is also feasible in extracting metals such as nickel and cobalt from ores that normally are difficult to enrich and process metallurgically. The salt extraction process is based on extraction of the metals from the raw materials by a molten salt bath consisting of NaCl, LiCl, and KCl corresponding to the eutectic composition with AlCl3 as the chlorinating agent. The process is operated in the temperature range 973 K (700°C) to 1173 K (900°C). The process was shown to be successful in extracting Cr and Fe from electric arc furnace (EAF) slag. Electrolytic copper could be produced from copper concentrate based on chalcopyrite in a single step. Conducting the process in oxygen-free atmosphere, sulfur could be captured in the elemental form. The method proved to be successful in extracting lead from spent cathode ray tubes. In order to prevent the loss of AlCl3 in the vapor form and also chlorine gas emission at the cathode during the electrolysis, liquid aluminum was used. The process was shown to be successful in extracting Nd and Dy from magnetic scrap. The method is a highly promising process route for the recovery of strategic metals. It also has the added advantage of being environmentally friendly.

  18. Experimental study on fragmentation behaviors of molten LBE and water contact interface

    Institute of Scientific and Technical Information of China (English)

    黄望哩; 洒荣园; 周丹娜; 姜华磊; 黄群英

    2015-01-01

    Based on the design of CLEAR (China LEAd-based Reactor), it is important to study the molten LBE (Lead-Bismuth Eutectic)/water interaction following an incidental steam generator tube rupture (SGTR) accident. Experiments were carried out to investigate the fragmentation behavior of the molten LBE/water contacting interface, with a high-speed video camera to record the fragmentation behavior of 300–600◦C LBE at 20◦C and 80◦C of water temperature. Violent explosion phenomenon occurred at water temperature of 20◦C, while no explosion occurred at 80◦C. Shapes of the LBE debris became round at 80◦C of water temperature, whereas the debris was of the needle-like shape at 20◦C. For all the molten LBE and water temperatures in the present study, the debris sized at 2.8–5.0 mm had the largest mass fraction. The results indicate that the dominant physical mechanism of the molten LBE fragmentation was the Kelvin-Helmholtz instability between LBE/water direct contact interface.

  19. Acquisition and processing of coaxial image of molten pool and keyhole in Nd:YAG laser welding with high power

    Institute of Scientific and Technical Information of China (English)

    秦国梁; 齐秀滨; 杨永波; 王旭友; 林尚扬

    2004-01-01

    An experimental setup of acquiring the coaxial visual image of the molten pool and keyhole in high power Nd:YAG laser welding is introduced in this paper. It is one of the most difficult problems in acquiring coaxial image that the coaxial imaging signal of molten pool and keyhole must be separated from the laser beam with high power. This problem was resolved by designing a dichroitic spectroscope. The characteristics of imaging signal were analyzed and the coaxial image of molten pool and keyhole was acquired. A smoothing filter and a homomorphic filter were designed to remove the low frequency noise and to enhance the image according to the characteristics of imaging signal. At last, edges of molten pool and keyhole were detected and extracted based on image segmentation with threshold.

  20. Edge detection of molten pool and weld line for CO2 welding based on B-spline wavelet

    Institute of Scientific and Technical Information of China (English)

    薛家祥; 贾林; 李海宝; 张丽玲

    2004-01-01

    Due to the disturbances of spatters, dusts and strong arc light, it is difficult to detect the molten pool edge and the weld line location in CO2 welding processes. The median filtering and self-multiplication was employed to preprocess the image of the CO2 welding in order to detect effectively the edge of molten pool and the location of weld line. The B-spline wavelet algorithm has been investigated, the influence of different scales and thresholds on the results of the edge detection have been compared and analyzed. The experimental results show that better performance to extract the edge of the molten pool and the location of weld line can be obtained by using the B-spline wavelet transform. The proposed edge detection approach can be further applied to the control of molten depth and the seam tracking.

  1. Study of the pyrochemical treatment-recycling process of the Molten Salt Reactor fuel; Estudio de sistema de un proceso de tratamiento-reciclaje piroquimico del combustible de un reactor de sales fundidas

    Energy Technology Data Exchange (ETDEWEB)

    Boussier, H.; Heuer, D.

    2010-07-01

    The Separation Processes Studies Laboratory (Commissariat a l'energie Atomique) has made a preliminary assessment of the reprocessing system associated with Molten Salt Fast Reactor (MSFR). The scheme studied in this paper is based on the principle of reductive extraction and metal transfer that constituted the core process designed for the Molten Salt Breeder Reactor (MSBR), although the flow diagram has been adapted to the current needs of the Molten Salt Fast Reactor (MSFR).

  2. Production of Oxygen from Lunar Regolith by Molten Oxide Electrolysis

    Science.gov (United States)

    Curreri, Peter A.

    2009-01-01

    This paper describes the use of the molten oxide electrolysis (MOE) process for the extraction of oxygen for life support and propellant, and silicon and metallic elements for use in fabrication on the Moon. The Moon is rich in mineral resources, but it is almost devoid of chemical reducing agents, therefore, molten oxide electrolysis is ideal for extraction, since the electron is the only practical reducing agent. MOE has several advantages over other extraction methods. First, electrolytic processing offers uncommon versatility in its insensitivity to feedstock composition. Secondly, oxide melts boast the twin key attributes of highest solubilizing capacity for regolith and lowest volatility of any candidate electrolytes. The former is critical in ensuring high productivity since cell current is limited by reactant solubility, while the latter simplifies cell design by obviating the need for a gas-tight reactor to contain evaporation losses as would be the case with a gas or liquid phase fluoride reagent operating at such high temperatures. Alternatively, MOE requires no import of consumable reagents (e.g. fluorine and carbon) as other processes do, and does not rely on interfacing multiple processes to obtain refined products. Electrolytic processing has the advantage of selectivity of reaction in the presence of a multi-component feed. Products from lunar regolith can be extracted in sequence according to the stabilities of their oxides as expressed by the values of the free energy of oxide formation (e.g. chromium, manganese, Fe, Si, Ti, Al, magnesium, and calcium). Previous work has demonstrated the viability of producing Fe and oxygen from oxide mixtures similar in composition to lunar regolith by molten oxide electrolysis (electrowinning), also called magma electrolysis having shown electrolytic extraction of Si from regolith simulant. This paper describes recent advances in demonstrating the MOE process by a joint project with participation by NASA KSC and

  3. Production of Oxygen from Lunar Regolith by Molten Oxide Electrolysis

    Science.gov (United States)

    Curreri, Peter A.

    2009-01-01

    This paper describes the use of the molten oxide electrolysis (MOE) process for the extraction of oxygen for life support and propellant, and silicon and metallic elements for use in fabrication on the Moon. The Moon is rich in mineral resources, but it is almost devoid of chemical reducing agents, therefore, molten oxide electrolysis is ideal for extraction, since the electron is the only practical reducing agent. MOE has several advantages over other extraction methods. First, electrolytic processing offers uncommon versatility in its insensitivity to feedstock composition. Secondly, oxide melts boast the twin key attributes of highest solubilizing capacity for regolith and lowest volatility of any candidate electrolytes. The former is critical in ensuring high productivity since cell current is limited by reactant solubility, while the latter simplifies cell design by obviating the need for a gas-tight reactor to contain evaporation losses as would be the case with a gas or liquid phase fluoride reagent operating at such high temperatures. Alternatively, MOE requires no import of consumable reagents (e.g. fluorine and carbon) as other processes do, and does not rely on interfacing multiple processes to obtain refined products. Electrolytic processing has the advantage of selectivity of reaction in the presence of a multi-component feed. Products from lunar regolith can be extracted in sequence according to the stabilities of their oxides as expressed by the values of the free energy of oxide formation (e.g. chromium, manganese, Fe, Si, Ti, Al, magnesium, and calcium). Previous work has demonstrated the viability of producing Fe and oxygen from oxide mixtures similar in composition to lunar regolith by molten oxide electrolysis (electrowinning), also called magma electrolysis having shown electrolytic extraction of Si from regolith simulant. This paper describes recent advances in demonstrating the MOE process by a joint project with participation by NASA KSC and

  4. Parameters of gas tube extraction technology in the upper corner of working face%回采工作面上隅角瓦斯拖管抽采技术参数研究

    Institute of Scientific and Technical Information of China (English)

    吴兵; 雷柏伟; 华明国; 管海鹤; 赵志研

    2014-01-01

    In view of the bad extraction effect for discontinuous space position of extraction point, se-rious waste of pipe and high extraction cost in the traditional buried tube gas extraction technology in upper corner of working face, the gas tube extraction technology in the upper corner was introduced in this paper, which can make the extraction point matching the face advancing speed, realize the continu-ity of the best goaf gas extraction effect, recover pipes and materials, and reduce the extraction cost. The selection of optimal location of goaf gas extraction, namely the determination of extraction parameters, is the successful implementation of gas tube extraction of the upper corner. The behavior of gas diffu-sion and flow were described by using Brinkman equation, Fick diffusion law and gas diffusion transla-tion equation, and the multi-physical field coupling model of gas flow in working face was established. Then, the optimal layout parameters of the tube extraction were determined by Fluent calculation of the model, and was applied to the practice and effect test. The results show that the numerical simulations are basically in accordance with the field test results, and the optimum extraction position has been de-termined as 2.4 m from the floor, 1.57 m from the air-return roadway along the inclined direction, and 17.4 m deep into the goaf along the strike. Gas overrun in the upper corner has been eliminated during the application, which proves that the gas tube extraction technology in the upper corner has a good ap-plicability and feasibility.%针对传统埋管抽放上隅角瓦斯技术中抽放点在空间位置不连续抽放效果差、管材浪费严重抽放成本高等重大缺陷,提出了上隅角瓦斯拖管抽采技术,可使抽放点匹配工作面推进速度,实现了采空区瓦斯抽放最佳效果的连续性,并且能回收管材降低抽放成本。采空区瓦斯抽放最佳位置的选择即抽放参数的确定是成功实

  5. Molten fatty acid based microemulsions.

    Science.gov (United States)

    Noirjean, Cecile; Testard, Fabienne; Dejugnat, Christophe; Jestin, Jacques; Carriere, David

    2016-06-21

    We show that ternary mixtures of water (polar phase), myristic acid (MA, apolar phase) and cetyltrimethylammonium bromide (CTAB, cationic surfactant) studied above the melting point of myristic acid allow the preparation of microemulsions without adding a salt or a co-surfactant. The combination of SANS, SAXS/WAXS, DSC, and phase diagram determination allows a complete characterization of the structures and interactions between components in the molten fatty acid based microemulsions. For the different structures characterized (microemulsion, lamellar or hexagonal phases), a similar thermal behaviour is observed for all ternary MA/CTAB/water monophasic samples and for binary MA/CTAB mixtures without water: crystalline myristic acid melts at 52 °C, and a thermal transition at 70 °C is assigned to the breaking of hydrogen bounds inside the mixed myristic acid/CTAB complex (being the surfactant film in the ternary system). Water determines the film curvature, hence the structures observed at high temperature, but does not influence the thermal behaviour of the ternary system. Myristic acid is partitioned in two "species" that behave independently: pure myristic acid and myristic acid associated with CTAB to form an equimolar complex that plays the role of the surfactant film. We therefore show that myristic acid plays the role of a solvent (oil) and a co-surfactant allowing the fine tuning of the structure of oil and water mixtures. This solvosurfactant behaviour of long chain fatty acid opens the way for new formulations with a complex structure without the addition of any extra compound.

  6. In vivo monitoring of quantum dots in the extracellular space using push-pull perfusion sampling, online in-tube solid phase extraction, and inductively coupled plasma mass spectrometry.

    Science.gov (United States)

    Su, C K; Huang, C W; Yang, C S; Wang, Y J; Sun, Y C

    2010-09-01

    To monitor the dynamic changes of extracellular quantum dots (QDs) in vivo in the livers of anesthetized rats, we developed an automatic online analytical system comprising push-pull perfusion (PPP) sampling, the established in-tube solid phase extraction (SPE) procedure, and inductively coupled plasma mass spectrometry (ICPMS). The method takes advantage of the retention of QDs onto the interior surface of a polytetrafluoroethylene (PTFE) tube as a means of extracting the QDs from complicated push-pull perfusates. For the injected QDs present in the liver extracellular fluid (ECF) at low picomolar levels, a temporal resolution of 10 min was required to collect sufficient amounts of QDs to meet the sensitivity requirements of the ICPMS system. To the best of our knowledge, this study is the first to exploit the PPP technique for the collection of QDs from living animals and PTFE tubing as a SPE adsorbent for the online extraction of QDs and the removal of biological matrix prior to ICPMS analysis of cadmium-containing inorganic nanocrystal. We confirmed the analytical reliability of this method from measurements of the spike recoveries of saline samples; in addition, we demonstrated the systems' applicability through in vivo monitoring of the time-dependent concentration profile of liver extracellular QDs in living rats after intravenous administration.

  7. Physical properties of molten carbonate electrolyte

    Energy Technology Data Exchange (ETDEWEB)

    Kojima, T.; Yanagida, M.; Tanimoto, K. [Osaka National Research Institute (Japan)] [and others

    1996-12-31

    Recently many kinds of compositions of molten carbonate electrolyte have been applied to molten carbonate fuel cell in order to avoid the several problems such as corrosion of separator plate and NiO cathode dissolution. Many researchers recognize that the addition of alkaline earth (Ca, Sr, and Ba) carbonate to Li{sub 2}CO{sub 3}-Na{sub 2}CO{sub 3} and Li{sub 2}CO{sub 3}-K{sub 2}CO{sub 3} eutectic electrolytes is effective to avoid these problems. On the other hand, one of the corrosion products, CrO{sub 4}{sup 2-} ion is found to dissolve into electrolyte and accumulated during the long-term MCFC operations. This would affect the performance of MCFC. There, however, are little known data of physical properties of molten carbonate containing alkaline earth carbonates and CrO{sub 4}{sup 2-}. We report the measured and accumulated data for these molten carbonate of electrical conductivity and surface tension to select favorable composition of molten carbonate electrolytes.

  8. Molten salt reactors - safety options galore

    Energy Technology Data Exchange (ETDEWEB)

    Gat, U. [Oak Ridge National Lab., TN (United States); Dodds, H.L. [Univ. of Tennessee, Knoxville, TN (United States)

    1997-03-01

    Safety features and attributes of molten salt reactors (MSR) are described. The unique features of fluid fuel reactors of on-line continuous processing and the ability for so-called external cooling result in simple and safe designs with low excess reactivity, low fission product inventory, and small source term. These, in turn, make a criticality accident unlikely and reduce the severity of a loss of coolant to where they are no longer severe accidents. A melt down is not an accident for a reactor that uses molten fuel. The molten salts are stable, non-reactive and efficient heat transfer media that operate at high temperatures at low pressures and are highly compatible with selected structural materials. All these features reduce the accident plethora. Freeze valves can be used for added safety. An ultimate safe reactor (U.S.R) is described with safety features that are passive, inherent and non-tamperable (PINT).

  9. Electroreduction Kinetics for Molten Oxide Slags

    Institute of Scientific and Technical Information of China (English)

    GAO Yun-ming; CHOU Kuo-chih; GUO Xing-min; WANG Wei

    2007-01-01

    The oxygen-ion conductor, the reducing agent, and the molten oxide slag containing electroactive matter were used as constituent of a galvanic cell. Metal was directly electroreduced from molten slag using a short-circuit galvanic cell. The following galvanic cell was assembled in the present experiment: graphite rod, [O]Fe-C saturated|ZrO2(MgO)|Cu(l)+(FeO)(slag), and molybdenum wire. The FeO electroreduction reaction was studied through measuring short circuit current by controlling factors such as temperature, the FeO content in molten slags, and the external circuit resistance. An overall kinetics model was developed to describe the process of FeO electroreduction. It was found that the modeled curves were in good agreement with the experimental values. The new oxide reduction method in the metallurgy with controlled oxygen flow was proposed and the metallurgical theory with controlled oxygen flow was developed.

  10. EXTRACT

    DEFF Research Database (Denmark)

    Pafilis, Evangelos; Buttigieg, Pier Luigi; Ferrell, Barbra

    2016-01-01

    The microbial and molecular ecology research communities have made substantial progress on developing standards for annotating samples with environment metadata. However, sample manual annotation is a highly labor intensive process and requires familiarity with the terminologies used. We have the...... and text-mining-assisted curation revealed that EXTRACT speeds up annotation by 15-25% and helps curators to detect terms that would otherwise have been missed.Database URL: https://extract.hcmr.gr/....

  11. Recovery of Nickel from Nickel-Based Superalloy Scraps by Utilizing Molten Zinc

    Science.gov (United States)

    Yagi, Ryohei; Okabe, Toru H.

    2017-02-01

    With the purpose of developing a new process for recycling nickel (Ni) directly from superalloy scraps, a fundamental study on the extraction and separation of Ni was carried out using molten zinc (Zn) as the extraction medium. In order to examine the reaction between molten Zn and the Ni-based superalloy, superalloy samples and Zn shots were heated at 1173 K (900 °C) for 6 hours. After heating, the superalloy samples fully reacted with Zn and dissolved in molten Zn. The Zn-alloyed sample obtained by slow cooling consisted of two separated upper and lower phases. In the upper part of the sample, only Zn and the Zn-Ni alloys were found; in the lower part, an intermetallic alloy consisting of refractory metals such as rhenium (Re) and tantalum (Ta) was found. This result shows that Ni and refractory metals contained in the scrap can be separated by utilizing the density differences between the Zn-Ni alloy and the refractory metals in molten Zn. Vacuum treatment of the upper part of the Zn-alloyed sample at 1173 K (900 °C) reduced the concentration of Zn in the sample from 97.0 to 0.4 mass pct. After Zn removal, a Ni alloy containing Ni with a purity of 85.3 to 86.1 mass pct and negligible quantities (scraps without the consumption of Zn or the generation of toxic wastes solutions.

  12. Direct contact heat recovery from molten salt

    Science.gov (United States)

    Technological deficiencies associated with efficient and economical retrieval of heat energy from molten salt systems are addressed. The large latent heat of fusion stored in molten salt hydrates and other candidate phase change materials (PCM) is removed by internal boiling of a volatile heat transfer fluid (HTF). This procedure eliminates the conventional use of submerged heat exchangers which are costly and, in crystallizing salts, ineffective. The thermochemical conditions and material properties that are critical for application of this concept in environments that yield significant energy savings are investigated and defined.

  13. Experimental studies of actinides in molten salts

    Energy Technology Data Exchange (ETDEWEB)

    Reavis, J.G.

    1985-06-01

    This review stresses techniques used in studies of molten salts containing multigram amounts of actinides exhibiting intense alpha activity but little or no penetrating gamma radiation. The preponderance of studies have used halides because oxygen-containing actinide compounds (other than oxides) are generally unstable at high temperatures. Topics discussed here include special enclosures, materials problems, preparation and purification of actinide elements and compounds, and measurements of various properties of the molten volts. Property measurements discussed are phase relationships, vapor pressure, density, viscosity, absorption spectra, electromotive force, and conductance. 188 refs., 17 figs., 6 tabs.

  14. Transient analysis of a molten salt central receiver (MSCR) in a solar power plant

    Science.gov (United States)

    Joshi, A.; Wang, C.; Akinjiola, O.; Lou, X.; Neuschaefer, C.; Quinn, J.

    2016-05-01

    Alstom is developing solar power tower plants utilizing molten salt as the working fluid. In solar power tower, the molten salt central receiver (MSCR) atop of the tower is constructed of banks of tubes arranged in panels creating a heat transfer surface exposed to the solar irradiation from the heliostat field. The molten salt heat transfer fluid (HTF), in this case 60/40%wt NaNO3-KNO3, flows in serpentine flow through the surface collecting sensible heat thus raising the HTF temperature from 290°C to 565°C. The hot molten salt is stored and dispatched to produce superheated steam in a steam generator, which in turn produces electricity in the steam turbine generator. The MSCR based power plant with a thermal energy storage system (TESS) is a fully dispatchable renewable power plant with a number of opportunities for operational and economic optimization. This paper presents operation and controls challenges to the MSCR and the overall power plant, and the use of dynamic model computer simulation based transient analyses applied to molten salt based solar thermal power plant. This study presents the evaluation of the current MSCR design, using a dynamic model, with emphasis on severe events affecting critical process response, such as MS temperature deviations, and recommend MSCR control design improvements based on the results. Cloud events are the scope of the transient analysis presented in this paper. The paper presents results from a comparative study to examine impacts or effects on key process variables related to controls and operation of the MSCR plant.

  15. Simulation on flow process of filtered molten metals

    Institute of Scientific and Technical Information of China (English)

    房文斌; 耿耀宏; 魏尊杰; 安阁英; 叶荣茂

    2002-01-01

    Filtration and flow process of molten metals was analyzed by water simulation experiments. Fluid dynamic phenomena of molten metal cells through a foam ceramic filter was described and calculated by ERGOR equation as well. The results show that the filter is most useful for stable molten metals and the filtered flow is laminar, so that inclusions can be removed more effectively.

  16. Oxygen electrode in molten carbonate fuel cells

    Science.gov (United States)

    Dave, B. B.; White, R. E.; Srinivasan, S.; Appleby, A. J.

    1990-12-01

    During this quarter, impedance data were analyzed for an oxygen reduction process in molten carbonate electrolyte and a manuscript, Impedance Analysis for Oxygen Reduction in a Lithium Carbonate Melt: Effects of Partial Pressure of Carbon Dioxide and Temperature, was prepared to be submitted to Journal of the Electrochemical Society for publication.

  17. Gastrostomy Tube (G-Tube)

    Science.gov (United States)

    ... the recovery room, sometimes called the "post-op" (post-operative) room or PACU (post-anesthesia care unit), and ... site; discharge that's yellow, green, or foul-smelling; fever) excessive bleeding or drainage from the tube site ...

  18. Heat transfer behavior of molten nitrate salt

    Science.gov (United States)

    Das, Apurba K.; Clark, Michael M.; Teigen, Bard C.; Fiveland, Woodrow A.; Anderson, Mark H.

    2016-05-01

    The usage of molten nitrate salt as heat transfer fluid and thermal storage medium decouples the generation of electricity from the variable nature of the solar resource, allowing CSP plants to avoid curtailment and match production with demand. This however brings some unique challenges for the design of the molten salt central receiver (MSCR). An aspect critical to the use of molten nitrate (60wt%/40wt% - NaNO3/KNO3) salt as heat transfer fluid in the MSCR is to understand its heat transfer behavior. Alstom collaborated with the University of Wisconsin to conduct a series of experiments and experimentally determined the heat transfer coefficients of molten nitrate salt up to high Reynolds number (Re > 2.0E5) and heat flux (q″ > 1000 kW/m2), conditions heretofore not reported in the literature. A cartridge heater instrumented with thermocouples was installed inside a stainless steel pipe to form an annular test section. The test section was installed in the molten salt flow loop at the University of Wisconsin facility, and operated over a range of test conditions to determine heat transfer data that covered the expected operating regime of a practical molten salt receiver. Heat transfer data were compared to widely accepted correlations found in heat transfer literature, including that of Gnielinski. At lower Reynolds number conditions, the results from this work concurred with the molten salt heat transfer data reported in literature and followed the aforementioned correlations. However, in the region of interest for practical receiver design, the correlations did not accurately model the experimentally determined heat transfer data. Two major effects were observed: (i) all other factors remaining constant, the Nusselt numbers gradually plateaued at higher Reynolds number; and (ii) at higher Reynolds number a positive interaction of heat flux on Nusselt number was noted. These effects are definitely not modeled by the existing correlations. In this paper a new

  19. Molten salt steam generator subsystem research experiment. Volume I. Phase 1 - Final report

    Energy Technology Data Exchange (ETDEWEB)

    None

    1984-10-01

    A study was conducted for Phase 1 of a two-phase project whose objectives were to develop a reliable, cost-effective molten salt steam generating subsystem for solar thermal plants, minimize uncertainty in capital, operating, and maintenance costs, and demonstrate the ability of molten salt to generate high-pressure, high-temperature steam. The Phase 1 study involved the conceptual design of molten salt steam generating subsystems for a nominal 100-MWe net stand-alone solar central receiver electric generating plant, and a nominal 100-MWe net hybrid fossil-fueled electric power generating plant that is 50% repowered by a solar central receiver system. As part of Phase 1, a proposal was prepared for Phase 2, which involves the design, construction, testing and evaluation of a Subsystem Research Experiment of sufficient size to ensure successful operation of the full-size subsystem designed in Phase 1. Evaluation of several concepts resulted in the selection of a four-component (preheater, evaporator, superheater, reheater), natural circulation, vertically oriented, shell and tube (straight) heat exchanger arrangement. Thermal hydraulic analysis of the system included full and part load performance, circulation requirements, stability, and critical heat flux analysis. Flow-induced tube vibration, tube buckling, fatigue evaluation of tubesheet junctions, steady-state tubesheet analysis, and a simplified transient analysis were included in the structural analysis of the system. Operating modes and system dynamic response to load changes were identified. Auxiliary equipment, fabrication, erection, and maintenance requirements were also defined. Installed capital costs and a project schedule were prepared for each design.

  20. Feet sunk in molten aluminium: The burn and its prevention.

    Science.gov (United States)

    Alonso-Peña, David; Arnáiz-García, María Elena; Valero-Gasalla, Javier Luis; Arnáiz-García, Ana María; Campillo-Campaña, Ramón; Alonso-Peña, Javier; González-Santos, Jose María; Fernández-Díaz, Alaska Leonor; Arnáiz, Javier

    2015-08-01

    Nowadays, despite improvements in safety rules and inspections in the metal industry, foundry workers are not free from burn accidents. Injuries caused by molten metals include burns secondary to molten iron, aluminium, zinc, copper, brass, bronze, manganese, lead and steel. Molten aluminium is one of the most common causative agents of burns (60%); however, only a few publications exist concerning injuries from molten aluminium. The main mechanisms of lesion from molten aluminium include direct contact of the molten metal with the skin or through safety apparel, or when the metal splash burns through the pants and rolls downward along the leg. Herein, we report three cases of deep dermal burns after 'soaking' the foot in liquid aluminium and its evolutive features. This paper aims to show our experience in the management of burns due to molten aluminium. We describe the current management principles and the key features of injury prevention. Copyright © 2014 Elsevier Ltd and ISBI. All rights reserved.

  1. High Power Molten Targets for Radioactive Ion Beam Production: from Particle Physics to Medical Applications

    CERN Document Server

    De Melo Mendonca, T M

    2014-01-01

    Megawatt-class molten targets, combining high material densities and good heat transfer properties are being considered for neutron spallation sources, neutrino physics facilities and radioactive ion beam production. For this last category of facilities, in order to cope with the limitation of long diffusion times affecting the extraction of short-lived isotopes, a lead-bismuth eutectic (LBE) target loop equipped with a diffusion chamber has been proposed and tested offline during the EURISOL design study. To validate the concept, a molten LBE loop is now in the design phase and will be prototyped and tested on-line at CERN-ISOLDE. This concept was further extended to an alternative route to produce 1013 18Ne/s for the Beta Beams, where a molten salt loop would be irradiated with 7 mA, 160 MeV proton beam. Some elements of the concept have been tested by using a molten fluoride salt static unit at CERNISOLDE. The investigation of the release and production of neon isotopes allowed the measurement of the diffu...

  2. Dynamics of the Molten Contact Line

    Science.gov (United States)

    Sonin, Ain A.; Duthaler, Gregg; Liu, Michael; Torresola, Javier; Qiu, Taiqing

    1999-01-01

    The purpose of this program is to develop a basic understanding of how a molten material front spreads over a solid that is below its melting point, arrests, and freezes. Our hope is that the work will contribute toward a scientific knowledge base for certain new applications involving molten droplet deposition, including the "printing" of arbitrary three-dimensional objects by precise deposition of individual molten microdrops that solidify after impact. Little information is available at this time on the capillarity-driven motion and arrest of molten contact line regions. Schiaffino and Sonin investigated the arrest of the contact line of a molten microcrystalline wax spreading over a subcooled solid "target" of the same material. They found that contact line arrest takes place at an apparent liquid contact angle that depends primarily on the Stefan number S=c(T(sub f) -T(sub t)/L based on the temperature difference between the fusion point and the target temperature, and proposed that contact line arrest occurs when the liquid's dynamic contact angle approaches the angle of attack of the solidification front just behind the contact line. They also showed, however, that the conventional continuum equations and boundary conditions have no meaningful solution for this angle. The solidification front angle is determined by the heat flux just behind the contact line, and the heat flux is singular at that point. By comparing experiments with numerical computations, Schiaffino and Sonin estimated that the conventional solidification model must break down within a distance of order 0.1 - 1 microns of the contact line. The physical mechanism for this breakdown is as yet undetermined, and no first-principles theory exists for the contact angle at arrest. Schiaffino and Sonin also presented a framework for understanding how to moderate Weber number molten droplet deposition in terms of similarity laws and experimentation. The study is based on experiments with three molten

  3. An evaluation of possible next-generation high temperature molten-salt power towers.

    Energy Technology Data Exchange (ETDEWEB)

    Kolb, Gregory J.

    2011-12-01

    Since completion of the Solar Two molten-salt power tower demonstration in 1999, the solar industry has been developing initial commercial-scale projects that are 3 to 14 times larger. Like Solar Two, these initial plants will power subcritical steam-Rankine cycles using molten salt with a temperature of 565 C. The main question explored in this study is whether there is significant economic benefit to develop future molten-salt plants that operate at a higher receiver outlet temperature. Higher temperatures would allow the use of supercritical steam cycles that achieve an improved efficiency relative to today's subcritical cycle ({approx}50% versus {approx}42%). The levelized cost of electricity (LCOE) of a 565 C subcritical baseline plant was compared with possible future-generation plants that operate at 600 or 650 C. The analysis suggests that {approx}8% reduction in LCOE can be expected by raising salt temperature to 650 C. However, most of that benefit can be achieved by raising the temperature to only 600 C. Several other important insights regarding possible next-generation power towers were also drawn: (1) the evaluation of receiver-tube materials that are capable of higher fluxes and temperatures, (2) suggested plant reliability improvements based on a detailed evaluation of the Solar Two experience, and (3) a thorough evaluation of analysis uncertainties.

  4. Molten uranium dioxide structure and dynamics.

    Science.gov (United States)

    Skinner, L B; Benmore, C J; Weber, J K R; Williamson, M A; Tamalonis, A; Hebden, A; Wiencek, T; Alderman, O L G; Guthrie, M; Leibowitz, L; Parise, J B

    2014-11-21

    Uranium dioxide (UO2) is the major nuclear fuel component of fission power reactors. A key concern during severe accidents is the melting and leakage of radioactive UO2 as it corrodes through its zirconium cladding and steel containment. Yet, the very high temperatures (>3140 kelvin) and chemical reactivity of molten UO2 have prevented structural studies. In this work, we combine laser heating, sample levitation, and synchrotron x-rays to obtain pair distribution function measurements of hot solid and molten UO2. The hot solid shows a substantial increase in oxygen disorder around the lambda transition (2670 K) but negligible U-O coordination change. On melting, the average U-O coordination drops from 8 to 6.7 ± 0.5. Molecular dynamics models refined to this structure predict higher U-U mobility than 8-coordinated melts.

  5. Molten metal holder furnace and casting system incorporating the molten metal holder furnace

    Science.gov (United States)

    Kinosz, Michael J.; Meyer, Thomas N.

    2003-02-11

    A bottom heated holder furnace (12) for containing a supply of molten metal includes a storage vessel (30) having sidewalls (32) and a bottom wall (34) defining a molten metal receiving chamber (36). A furnace insulating layer (42) lines the molten metal receiving chamber (36). A thermally conductive heat exchanger block (54) is located at the bottom of the molten metal receiving chamber (36) for heating the supply of molten metal. The heat exchanger block (54) includes a bottom face (65), side faces (66), and a top face (67). The heat exchanger block (54) includes a plurality of electrical heaters (70) extending therein and projecting outward from at least one of the faces of the heat exchanger block (54), and further extending through the furnace insulating layer (42) and one of the sidewalls (32) of the storage vessel (30) for connection to a source of electrical power. A sealing layer (50) covers the bottom face (65) and side faces (66) of the heat exchanger block (54) such that the heat exchanger block (54) is substantially separated from contact with the furnace insulating layer (42).

  6. Multiply manifolded molten carbonate fuel cells

    Energy Technology Data Exchange (ETDEWEB)

    Krumpelt, M.; Roche, M.F.; Geyer, H.K.; Johnson, S.A.

    1994-08-01

    This study consists of research and development activities related to the concept of a molten carbonate fuel cell (MCFC) with multiple manifolds. Objective is to develop an MCFC having a higher power density and a longer life than other MCFC designs. The higher power density will result from thinner gas flow channels; the extended life will result from reduced temperature gradients. Simplification of the gas flow channels and current collectors may also significantly reduce cost for the multiply manifolded MCFC.

  7. Coupled optical and thermal detailed simulations for the accurate evaluation and performance improvement of molten salts solar towers

    Science.gov (United States)

    García-Barberena, Javier; Mutuberria, Amaia; Palacin, Luis G.; Sanz, Javier L.; Pereira, Daniel; Bernardos, Ana; Sanchez, Marcelino; Rocha, Alberto R.

    2017-06-01

    The National Renewable Energy Centre of Spain, CENER, and the Technology & Innovation area of ACS Cobra, as a result of their long term expertise in the CSP field, have developed a high-quality and high level of detail optical and thermal simulation software for the accurate evaluation of Molten Salts Solar Towers. The main purpose of this software is to make a step forward in the state-of-the-art of the Solar Towers simulation programs. Generally, these programs deal with the most critical systems of such plants, i.e. the solar field and the receiver, on an independent basis. Therefore, these programs typically neglect relevant aspects in the operation of the plant as heliostat aiming strategies, solar flux shapes onto the receiver, material physical and operational limitations, transient processes as preheating and secure cloud passing operating modes, and more. The modelling approach implemented in the developed program consists on effectively coupling detailed optical simulations of the heliostat field with also detailed and full-transient thermal simulations of the molten salts tube-based external receiver. The optical model is based on an accurate Monte Carlo ray-tracing method which solves the complete solar field by simulating each of the heliostats at once according to their specific layout in the field. In the thermal side, the tube-based cylindrical external receiver of a Molten Salts Solar Tower is modelled assuming one representative tube per panel, and implementing the specific connection layout of the panels as well as the internal receiver pipes. Each tube is longitudinally discretized and the transient energy and mass balances in the temperature dependent molten salts and steel tube models are solved. For this, a one dimensional radial heat transfer model based is used. The thermal model is completed with a detailed control and operation strategy module, able to represent the appropriate operation of the plant. An integration framework has been

  8. Thermal Characterization of Molten Salt Systems

    Energy Technology Data Exchange (ETDEWEB)

    Toni Y. Gutknecht; Guy L. Fredrickson

    2011-09-01

    The phase stability of molten salts in an electrorefiner (ER) may be adversely affected by the buildup of sodium, fission products, and transuranics in the electrolyte. Potential situations that need to be avoided are the following: (1) salt freezing due to an unexpected change in the liquidus temperature, (2) phase separation or non-homogeneity of the molten salt due to the precipitation of solids or formation of immiscible liquids, and (3) any mechanism that can result in the separation and concentration of fissile elements from the molten salt. Any of these situations would result in an off-normal condition outside the established safety basis for electrorefiner (ER) operations. The stability (and homogeneity) of the phases can potentially be monitored through the thermal characterization of the salts, which can be a function of impurity concentration. This report describes the experimental results of typical salts compositions, which consist of chlorides of potassium, lithium, strontium, samarium, praseodymium, lanthanum, barium, cerium, cesium, neodymium, sodium and gadolinium chlorides as a surrogate for both uranium and plutonium, used for the processing of used nuclear fuels.

  9. Supported Molten Metal Membranes for Hydrogen Separation

    Energy Technology Data Exchange (ETDEWEB)

    Datta, Ravindra; Ma, Yi Hua; Yen, Pei-Shan; Deveau, Nicholas; Fishtik, Ilie; Mardilovich, Ivan

    2013-09-30

    We describe here our results on the feasibility of a novel dense metal membrane for hydrogen separation: Supported Molten Metal Membrane, or SMMM.1 The goal in this work was to develop these new membranes based on supporting thin films of low-melting, non- precious group metals, e.g., tin (Sn), indium (In), gallium (Ga), or their alloys, to provide a flux and selectivity of hydrogen that rivals the conventional but substantially more expensive palladium (Pd) or Pd alloy membranes, which are susceptible to poisoning by the many species in the coal-derived syngas, and further possess inadequate stability and limited operating temperature range. The novelty of the technology presented numerous challenges during the course of this project, however, mainly in the selection of appropriate supports, and in the fabrication of a stable membrane. While the wetting instability of the SMMM remains an issue, we did develop an adequate understanding of the interaction between molten metal films with porous supports that we were able to find appropriate supports. Thus, our preliminary results indicate that the Ga/SiC SMMM at 550 ºC has a permeance that is an order of magnitude higher than that of Pd, and exceeds the 2015 DOE target. To make practical SMM membranes, however, further improving the stability of the molten metal membrane is the next goal. For this, it is important to better understand the change in molten metal surface tension and contact angle as a function of temperature and gas-phase composition. A thermodynamic theory was, thus, developed, that is not only able to explain this change in the liquid-gas surface tension, but also the change in the solid-liquid surface tension as well as the contact angle. This fundamental understanding has allowed us to determine design characteristics to maintain stability in the face of changing gas composition. These designs are being developed. For further progress, it is also important to understand the nature of solution and

  10. Chest tube insertion

    Science.gov (United States)

    ... tube insertion; Insertion of tube into chest; Tube thoracostomy; Pericardial drain ... Kirsch TD, Sax J. Tube thoracostomy. In: Roberts JR, ed. Roberts and ... . 6th ed. Philadelphia, PA: Elsevier Saunders; 2014:chap 10.

  11. Jejunostomy feeding tube

    Science.gov (United States)

    ... page: //medlineplus.gov/ency/patientinstructions/000181.htm Jejunostomy feeding tube To use the sharing features on this ... vomiting Your child's stomach is bloated Alternate Names Feeding - jejunostomy tube; G-J tube; J-tube; Jejunum ...

  12. Observations of actively forming lava tubes and associated structures, Hawaii, part 2

    Science.gov (United States)

    Greeley, R.

    1971-01-01

    A ground examination is made of lave tubes and channels. The surface morphology and the changes noted through lava flow activity are cited, and compared to earlier aerial observations. The lava activity was believed to be caused by a small lava lake exposed by the collapse of a crust covering it. Drainage of the lake was caused by a fissure erruption. New tubes or extensions of existing ones were noted from the flow. Molten lava was not seen in any tubes examined on the ground, but some of the flows were not sufficiently cooled to allow subsurface examination and survey of the tubes.

  13. Crust formation and its effect on the molten pool coolability

    Energy Technology Data Exchange (ETDEWEB)

    Park, R.J.; Lee, S.J.; Sim, S.K. [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

    1995-09-01

    Experimental and analytical studies of the crust formation and its effect on the molten pool coolability have been performed to examine the crust formation process as a function of boundary temperatures as well as to investigate heat transfer characteristics between molten pool and overlying water in order to evaluate coolability of the molten pool. The experimental test results have shown that the surface temperature of the bottom plate is a dominant parameter in the crust formation process of the molten pool. It is also found that the crust thickness of the case with direct coolant injection into the molten pool is greater than that of the case with a heat exchanger. Increasing mass flow rate of direct coolant injection to the molten pool does not affect the temperature of molten pool after the crust has been formed in the molten pool because the crust behaves as a thermal barrier. The Nusselt number between the molten pool and the coolant of the case with no crust formation is greater than that of the case with crust formation. The results of FLOW-3D analyses have shown that the temperature distribution contributes to the crust formation process due to Rayleigh-Benard natural convection flow.

  14. Novel Molten Salts Thermal Energy Storage for Concentrating Solar Power Generation

    Energy Technology Data Exchange (ETDEWEB)

    Reddy, Ramana G. [The University of Alabama

    2013-10-23

    go/no-go goals stipulated by the DOE for this project. Energy densities of all salt mixtures were higher than that of the current solar salt. The salt mixtures costs have been estimated and TES system costs for a 2 tank, direct approach have been estimated for each of these materials. All estimated costs are significantly below the baseline system that used solar salt. These lower melt point salts offer significantly higher energy density per volume than solar salt – and therefore attractively smaller inventory and equipment costs. Moreover, a new TES system geometry has been recommended A variety of approaches were evaluated to use the low melting point molten salt. Two novel changes are recommended that 1) use the salt as a HTF through the solar trough field, and 2) use the salt to not only create steam but also to preheat the condensed feedwater for Rankine cycle. The two changes enable the powerblock to operate at 500°C, rather than the current 400°C obtainable using oil as the HTF. Secondly, the use of salt to preheat the feedwater eliminates the need to extract steam from the low pressure turbine for that purpose. Together, these changes result in a dramatic 63% reduction required for 6 hour salt inventory, a 72% reduction in storage volume, and a 24% reduction in steam flow rate in the power block. Round trip efficiency for the Case 5 - 2 tank “direct” system is estimated at >97%, with only small losses from time under storage and heat exchange, and meeting RFP goals. This attractive efficiency is available because the major heat loss experienced in a 2 tank “indirect” system - losses by transferring the thermal energy from oil HTF to the salt storage material and back to oil to run the steam generator at night - is not present for the 2 tank direct system. The higher heat capacity values for both LMP and HMP systems enable larger storage capacities for concentrating solar power.

  15. Production and release of ISOL beams from molten fluoride salt targets

    Energy Technology Data Exchange (ETDEWEB)

    Mendonca, T.M., E-mail: taniamel@mail.cern.ch [IFIMUP and IN – Institut of Nanosciences and Nanotechnologies, Rua do Campo Alegre 687, 4169-007 Porto (Portugal); European Organization for Nuclear Research – CERN, 1211 Geneva 23 (Switzerland); Hodak, R. [Department of Nuclear Physics and Biophysics, Comenius University, Mlynska dolina F1, SK-842 15 Bratislava (Slovakia); Ghetta, V.; Allibert, M.; Heuer, D. [Laboratoire de Physique Subatomique et de Cosmologie – LPSC, 53 Rue des Martyrs, 38026 Grenoble Cedex (France); Noah, E. [Section de Physique, Université de Genève, 1211 Genève 4 (Switzerland); Cimmino, S. [European Organization for Nuclear Research – CERN, 1211 Geneva 23 (Switzerland); Delonca, M. [European Organization for Nuclear Research – CERN, 1211 Geneva 23 (Switzerland); IRTES-M3M, Université de Technologie de Belfort-Montbeliard, 90010 Belfort Cedex (France); IRTES-LERMPS, Université de Technologie de Belfort-Montbeliard, 90010 Belfort Cedex (France); Gottberg, A. [European Organization for Nuclear Research – CERN, 1211 Geneva 23 (Switzerland); Instituto de Estructura de la Materia CSIC, E28006 Madrid (Spain); Kronberger, M. [European Organization for Nuclear Research – CERN, 1211 Geneva 23 (Switzerland); Department of Physics, University of Jyväskylä, Survontie 9, Jyväskylä FI-40014 (Finland); Ramos, J.P. [European Organization for Nuclear Research – CERN, 1211 Geneva 23 (Switzerland); Department of Materials and Ceramics Engineering, University of Aveiro, CICECO, 3810-193 Aveiro (Portugal); and others

    2014-06-01

    In the framework of the Beta Beams project, a molten fluoride target has been proposed for the production of the required 10{sup 1318}Ne/s. The production and extraction of such rates are predicted to be possible on a circulating molten salt with 160 MeV proton beams at close to 1 MW power. As a most important step to validate the concept, a prototype has been designed and investigated at CERN-ISOLDE using a static target unit. The target material consisted of a binary fluoride system, NaF:LiF (39:61 mol.%), with melting point at 649 °C. The production of Ne beams has been monitored as a function of the target temperature and proton beam intensity. The prototype development and the results of the first online tests with 1.4 GeV proton beam are presented in this paper.

  16. Production and Release of ISOL Beams from Molten Fluoride Salt Targets

    CERN Document Server

    Mendonca, T M; Ghetta, V; Alibert, M; Heuer, D; Noah, E; Cimmino, S; Delonca, M; Gottberg, A; Kronberger, M; Ramos, J; Seiffert, C; Stora, T; CERN. Geneva. ATS Department

    2014-01-01

    In the framework of the Beta Beams study, a molten fluoride target has been proposed for the production of the required 1013 18Ne/s. The production and extraction of such rates are obtained on a circulating molten salt with proton beam energy beams at close to 1 MW power. As a most important step to validate the concept, a prototype has been designed and investigated at CERN-ISOLDE using a static target unit. The target material consisted of a binary fluoride system, NaF:LiF (39:61 % mol.), with melting point at 649ºC. The production of Ne beams has been monitored as a function of the target temperature and proton beam intensity. The prototype development and the results of the first online tests with 1.4 GeV proton beam are presented in this paper.

  17. photomultiplier tube

    CERN Multimedia

    photomultiplier tubes. A device to convert light into an electric signal (the name is often abbreviated to PM). Photomultipliers are used in all detectors based on scintillating material (i.e. based on large numbers of fibres which produce scintillation light at the passage of a charged particle). A photomultiplier consists of 3 main parts: firstly, a photocathode where photons are converted into electrons by the photoelectric effect; secondly, a multiplier chain consisting of a serie of dynodes which multiply the number of electron; finally, an anode, which collects the resulting current.

  18. photomultiplier tubes

    CERN Multimedia

    photomultiplier tubes. A device to convert light into an electric signal (the name is often abbreviated to PM). Photomultipliers are used in all detectors based on scintillating material (i.e. based on large numbers of fibres which produce scintillation light at the passage of a charged particle). A photomultiplier consists of 3 main parts: firstly, a photocathode where photons are converted into electrons by the photoelectric effect; secondly, a multiplier chain consisting of a serie of dynodes which multiply the number of electron; finally, an anode, which collects the resulting current.

  19. Electrochemical studies on plutonium in molten salts

    Energy Technology Data Exchange (ETDEWEB)

    Bourges, G. [CEA-Centre d' etudes de Valduc, 21 120 Is sur Tille (France)], E-mail: gilles.bourges@cea.fr; Lambertin, D.; Rochefort, S. [CEA-Centre d' etudes de Valduc, 21 120 Is sur Tille (France); Delpech, S.; Picard, G. [Laboratoire d' Electrochimie et de Chimie Analytique (UMR7575, CNRS), ENSCP, 11 rue Pierre et Marie Curie, 75231 Paris (France)

    2007-10-11

    Electrochemical studies on plutonium have been supporting the development of pyrochemical processes involving plutonium at CEA. The electrochemical properties of plutonium have been studied in molten salts - ternary eutectic mixture NaCl-KCl-BaCl{sub 2}, equimolar mixture NaCl-KCl and pure CaCl{sub 2} - and in liquid gallium at 1073 K. The formal, or apparent, standard potential of Pu(III)/Pu redox couple in eutectic mixture of NaCl-KCl-BaCl{sub 2} at 1073 K determined by potentiometry is equal to -2.56 V (versus Cl{sub 2}, 1 atm/Cl{sup -} reference electrode). In NaCl-KCl eutectic mixture and in pure CaCl{sub 2} the formal standard potentials deduced from cyclic voltammetry are respectively -2.54 V and -2.51 V. These potentials led to the calculation of the activity coefficients of Pu(III) in the molten salts. Chronoamperometry on plutonium in liquid gallium using molten chlorides - CaCl{sub 2} and equimolar NaCl/KCl - led to the determination of the activity coefficient of Pu in liquid Ga, log {gamma} = -7.3. This new data is a key parameter to assess the thermodynamic feasibility of a process using gallium as solvent metal. By comparing gallium with other solvent metals - cadmium, bismuth, aluminum - gallium appears to be, with aluminum, more favorable for the selectivity of the separation at 1073 K of plutonium from cerium. In fact, compared with a solid tungsten electrode, none of these solvent liquid metals is a real asset for the selectivity of the separation. The role of a solvent liquid metal is mainly to trap the elements.

  20. Apparatus for controlling molten core debris. [LMFBR

    Science.gov (United States)

    Golden, M.P.; Tilbrook, R.W.; Heylmun, N.F.

    1977-07-19

    Disclosed is an apparatus for containing, cooling, diluting, dispersing and maintaining subcritical the molten core debris assumed to melt through the bottom of a nuclear reactor pressure vessel in the unlikely event of a core meltdown. The apparatus is basically a sacrificial bed system which includes an inverted conical funnel, a core debris receptacle including a spherical dome, a spherically layered bed of primarily magnesia bricks, a cooling system of zig-zag piping in graphite blocks about and below the bed and a cylindrical liner surrounding the graphite blocks including a steel shell surrounded by firebrick. Tantalum absorber rods are used in the receptacle and bed. 9 claims, 22 figures.

  1. Thermal-hydraulics of internally heated molten salts and application to the Molten Salt Fast Reactor

    Science.gov (United States)

    Fiorina, Carlo; Cammi, Antonio; Luzzi, Lelio; Mikityuk, Konstantin; Ninokata, Hisashi; Ricotti, Marco E.

    2014-04-01

    The Molten Salt Reactors (MSR) are an innovative kind of nuclear reactors and are presently considered in the framework of the Generation IV International Forum (GIF-IV) for their promising performances in terms of low resource utilization, waste minimization and enhanced safety. A unique feature of MSRs is that molten fluoride salts play the distinctive role of both fuel (heat source) and coolant. The presence of an internal heat generation perturbs the temperature field and consequences are to be expected on the heat transfer characteristics of the molten salts. In this paper, the problem of heat transfer for internally heated fluids in a straight circular channel is first faced on a theoretical ground. The effect of internal heat generation is demonstrated to be described by a corrective factor applied to traditional correlations for the Nusselt number. It is shown that the corrective factor can be fully characterized by making explicit the dependency on Reynolds and Prandtl numbers. On this basis, a preliminary correlation is proposed for the case of molten fluoride salts by interpolating the results provided by an analytic approach previously developed at the Politecnico di Milano. The experimental facility and the related measuring procedure for testing the proposed correlation are then presented. Finally, the developed correlation is used to carry out a parametric investigation on the effect of internal heat generation on the main out-of-core components of the Molten Salt Fast Reactor (MSFR), the reference circulating-fuel MSR design in the GIF-IV. The volumetric power determines higher temperatures at the channel wall, but the effect is significant only in case of large diameters and/or low velocities.

  2. Effective emissivity of a blackbody cavity formed by two coaxial tubes.

    Science.gov (United States)

    Mei, Guohui; Zhang, Jiu; Zhao, Shumao; Xie, Zhi

    2014-04-10

    A blackbody cavity is developed for continuously measuring the temperature of molten steel, which consists of a cylindrical outer tube with a flat bottom, a coaxial inner tube, and an aperture diaphragm. The ray-tracing approach based on the Monte Carlo method was applied to calculate the effective emissivity for the isothermal cavity with the diffuse walls. And the dependences of the effective emissivity on the inner tube relative length were calculated for various inner tube radii, outer tube lengths, and wall emissivities. Results indicate that the effective emissivity usually has a maximum corresponding to the inner tube relative length, which can be explained by the impact of the inner tube relative length on the probability of the rays absorbed after two reflections. Thus, these results are helpful to the optimal design of the blackbody cavity.

  3. A tube-in-tube thermophotovoltaic generator

    Energy Technology Data Exchange (ETDEWEB)

    Ashcroft, J.; Campbell, B.; Depoy, D.

    1996-12-31

    A thermophotovoltaic device includes at least one thermal radiator tube, a cooling tube concentrically disposed within each thermal radiator tube and an array of thermophotovoltaic cells disposed on the exterior surface of the cooling tube. A shell having a first end and a second end surrounds the thermal radiator tube. Inner and outer tubesheets, each having an aperture corresponding to each cooling tube, are located at each end of the shell. The thermal radiator tube extends within the shell between the inner tubesheets. The cooling tube extends within the shell through the corresponding apertures of the two inner tubesheets to the corresponding apertures of the two outer tubesheets. A plurality of the thermal radiator tubes can be arranged in a staggered or an in-line configuration within the shell.

  4. Stable colloids in molten inorganic salts.

    Science.gov (United States)

    Zhang, Hao; Dasbiswas, Kinjal; Ludwig, Nicholas B; Han, Gang; Lee, Byeongdu; Vaikuntanathan, Suri; Talapin, Dmitri V

    2017-02-15

    A colloidal solution is a homogeneous dispersion of particles or droplets of one phase (solute) in a second, typically liquid, phase (solvent). Colloids are ubiquitous in biological, chemical and technological processes, homogenizing highly dissimilar constituents. To stabilize a colloidal system against coalescence and aggregation, the surface of each solute particle is engineered to impose repulsive forces strong enough to overpower van der Waals attraction and keep the particles separated from each other. Electrostatic stabilization of charged solutes works well in solvents with high dielectric constants, such as water (dielectric constant of 80). In contrast, colloidal stabilization in solvents with low polarity, such as hexane (dielectric constant of about 2), can be achieved by decorating the surface of each particle of the solute with molecules (surfactants) containing flexible, brush-like chains. Here we report a class of colloidal systems in which solute particles (including metals, semiconductors and magnetic materials) form stable colloids in various molten inorganic salts. The stability of such colloids cannot be explained by traditional electrostatic and steric mechanisms. Screening of many solute-solvent combinations shows that colloidal stability can be traced to the strength of chemical bonding at the solute-solvent interface. Theoretical analysis and molecular dynamics modelling suggest that a layer of surface-bound solvent ions produces long-ranged charge-density oscillations in the molten salt around solute particles, preventing their aggregation. Colloids composed of inorganic particles in inorganic melts offer opportunities for introducing colloidal techniques to solid-state science and engineering applications.

  5. Transient simulation of molten salt central receiver

    Science.gov (United States)

    Doupis, Dimitri; Wang, Chuan; Carcorze-Soto, Jorge; Chen, Yen-Ming; Maggi, Andrea; Losito, Matteo; Clark, Michael

    2016-05-01

    Alstom is developing concentrated solar power (CSP) utilizing 60/40wt% NaNO3-KNO3 molten salt as the working fluid in a tower receiver for the global renewable energy market. In the CSP power generation cycle, receivers undergo a daily cyclic operation due to the transient nature of solar energy. Development of robust and efficient start-up and shut-down procedures is critical to avoiding component failures due to mechanical fatigue resulting from thermal transients, thus maintaining the performance and availability of the CSP plant. The Molten Salt Central Receiver (MSCR) is subject to thermal transients during normal daily operation, a cycle that includes warmup, filling, operation, draining, and shutdown. This paper describes a study to leverage dynamic simulation and finite element analysis (FEA) in development of start-up, shutdown, and transient operation concepts for the MSCR. The results of the FEA also verify the robustness of the MSCR design to the thermal transients anticipated during the operation of the plant.

  6. Stable colloids in molten inorganic salts

    Science.gov (United States)

    Zhang, Hao; Dasbiswas, Kinjal; Ludwig, Nicholas B.; Han, Gang; Lee, Byeongdu; Vaikuntanathan, Suri; Talapin, Dmitri V.

    2017-02-01

    A colloidal solution is a homogeneous dispersion of particles or droplets of one phase (solute) in a second, typically liquid, phase (solvent). Colloids are ubiquitous in biological, chemical and technological processes, homogenizing highly dissimilar constituents. To stabilize a colloidal system against coalescence and aggregation, the surface of each solute particle is engineered to impose repulsive forces strong enough to overpower van der Waals attraction and keep the particles separated from each other. Electrostatic stabilization of charged solutes works well in solvents with high dielectric constants, such as water (dielectric constant of 80). In contrast, colloidal stabilization in solvents with low polarity, such as hexane (dielectric constant of about 2), can be achieved by decorating the surface of each particle of the solute with molecules (surfactants) containing flexible, brush-like chains. Here we report a class of colloidal systems in which solute particles (including metals, semiconductors and magnetic materials) form stable colloids in various molten inorganic salts. The stability of such colloids cannot be explained by traditional electrostatic and steric mechanisms. Screening of many solute–solvent combinations shows that colloidal stability can be traced to the strength of chemical bonding at the solute–solvent interface. Theoretical analysis and molecular dynamics modelling suggest that a layer of surface-bound solvent ions produces long-ranged charge-density oscillations in the molten salt around solute particles, preventing their aggregation. Colloids composed of inorganic particles in inorganic melts offer opportunities for introducing colloidal techniques to solid-state science and engineering applications.

  7. Measurement and analyses of molten Ni-Co alloy density

    Institute of Scientific and Technical Information of China (English)

    XIAO Feng; K. MUKAI; FANG Liang; FU Ya; YANG Ren-hui

    2006-01-01

    With the advent of powerful mathematical modeling techniques for material phenomena, there is renewed interest in reliable data for the density of the Ni-based superalloys. Up to now, there has been few report on the density of molten Ni-Co alloy.In order to obtain more accurate density data for molten Ni-Co alloy, the density of molten Ni-Co alloy was measured with a modified sessile drop method, and the accommodation of different atoms in molten Ni-Co alloy was analyzed. The density of alloy is found to decrease with increasing temperature and Co concentration in the alloy. The molar volume of molten Ni-Co alloy increases with increasing Co concentration. The molar volume of Ni-Co alloy determined shows a positive deviation from the linear molar volume, and the deviation of molar volume from ideal mixing increases with increasing Co concentration over the experimental concentration range.

  8. Selective Adsorption of Sodium Aluminum Fluoride Salts from Molten Aluminum

    Energy Technology Data Exchange (ETDEWEB)

    Leonard S. Aubrey; Christine A. Boyle; Eddie M. Williams; David H. DeYoung; Dawid D. Smith; Feng Chi

    2007-08-16

    Aluminum is produced in electrolytic reduction cells where alumina feedstock is dissolved in molten cryolite (sodium aluminum fluoride) along with aluminum and calcium fluorides. The dissolved alumina is then reduced by electrolysis and the molten aluminum separates to the bottom of the cell. The reduction cell is periodically tapped to remove the molten aluminum. During the tapping process, some of the molten electrolyte (commonly referred as “bath” in the aluminum industry) is carried over with the molten aluminum and into the transfer crucible. The carryover of molten bath into the holding furnace can create significant operational problems in aluminum cast houses. Bath carryover can result in several problems. The most troublesome problem is sodium and calcium pickup in magnesium-bearing alloys. Magnesium alloying additions can result in Mg-Na and Mg-Ca exchange reactions with the molten bath, which results in the undesirable pickup of elemental sodium and calcium. This final report presents the findings of a project to evaluate removal of molten bath using a new and novel micro-porous filter media. The theory of selective adsorption or removal is based on interfacial surface energy differences of molten aluminum and bath on the micro-porous filter structure. This report describes the theory of the selective adsorption-filtration process, the development of suitable micro-porous filter media, and the operational results obtained with a micro-porous bed filtration system. The micro-porous filter media was found to very effectively remove molten sodium aluminum fluoride bath by the selective adsorption-filtration mechanism.

  9. Casting Apparatus Including A Gas Driven Molten Metal Injector And Method

    Energy Technology Data Exchange (ETDEWEB)

    Trudel, David R. (Westlake, OH); Meyer, Thomas N. (Murrysville, PA); Kinosz, Michael J. (Apollo, PA); Arnaud, Guy (Morin Heights, CA); Bigler, Nicolas (Riviere-Beaudette, CA)

    2003-06-17

    The filtering molten metal injector system includes a holder furnace, a casting mold supported above the holder furnace, and at least one molten metal injector supported from a bottom side of the casting mold. The holder furnace contains a supply of molten metal. The mold defines a mold cavity for receiving the molten metal from the holder furnace. The molten metal injector projects into the holder furnace. The molten metal injector includes a cylinder defining a piston cavity housing a reciprocating piston for pumping the molten metal upward from the holder furnace to the mold cavity. The cylinder and piston are at least partially submerged in the molten metal when the holder furnace contains the molten metal. The cylinder or the piston includes a molten metal intake for receiving the molten metal into the piston cavity when the holder furnace contains molten metal. A conduit connects the piston cavity to the mold cavity. A molten metal filter is located in the conduit for filtering the molten metal passing through the conduit during the reciprocating movement of the piston. The molten metal intake may be a valve connected to the cylinder, a gap formed between the piston and an open end of the cylinder, an aperture defined in the sidewall of the cylinder, or a ball check valve incorporated into the piston. A second molten metal filter preferably covers the molten metal intake to the injector.

  10. Simulation tools and new developments of the molten salt fast reactor

    Energy Technology Data Exchange (ETDEWEB)

    Merle-Lucotte, E.; Doligez, X.; Heuer, D.; Allibert, M.; Ghetta, V. [LPSC-IN2P3-CNRS / UJF / Grenoble INP, 53 avenue des Martyrs, F-38026 Grenoble Cedex (France)

    2010-07-01

    Starting from the Molten Salt Breeder Reactor project of Oak-Ridge, we have performed parametric studies in terms of safety coefficients, reprocessing requirements and breeding capabilities. In the frame of this major re-evaluation of the molten salt reactor (MSR), we have developed a new concept called Molten Salt Fast Reactor or MSFR, based on the Thorium fuel cycle and a fast neutron spectrum. This concept has been selected for further studies by the MSR steering committee of the Generation IV International Forum in 2009. Our reactor's studies of the MSFR concept rely on numerical simulations making use of the MCNP neutron transport code coupled with a code for materials evolution which resolves the Bateman's equations giving the population of each nucleus inside each part of the reactor at each moment. Because of MSR's fundamental characteristics compared to classical solid-fuelled reactors, the classical Bateman equations have to be modified by adding two terms representing the reprocessing capacities and the fertile or fissile alimentation. We have thus coupled neutronic and reprocessing simulation codes in a numerical tool used to calculate the extraction efficiencies of fission products, their location in the whole system (reactor and reprocessing unit) and radioprotection issues. (authors)

  11. Solid-liquid solvent extraction of metal ions

    Institute of Scientific and Technical Information of China (English)

    Bo Peng; Haiyan Fan; Jinzhang Gao

    2003-01-01

    An overview of extraction of some trace metal ions using molten solvent (low melting substance) during last two decadesis presented. The development of this technique since its inception is briefly traced. The comparison of extraction efficiency, thermo-dynamics and kinetics mainly involving extraction of rare earth ions between molten solvent extraction at high temperature and usualliquid-liquid extraction at room temperature are discussed in detail. The various parameters obtained from the previous and presentstudies such as equilibrium extraction constant Kex, pH1/2, thermodynamic and kinetic data are displayed in tabular form. Finally, thecurrent demands, disadvantages and future prospects are also evaluated.

  12. Feeding tube - infants

    Science.gov (United States)

    ... this page: //medlineplus.gov/ency/article/007235.htm Feeding tube - infants To use the sharing features on this page, please enable JavaScript. A feeding tube is a small, soft, plastic tube placed ...

  13. Grain boundary wetness of partially molten dunite

    Science.gov (United States)

    Mu, S.; Faul, U.

    2013-12-01

    The grain scale melt distribution plays a key role for physical properties of partially molten regions in Earth's upper mantle, but our current understanding of the distribution of basaltic melt at the grain scale is still incomplete. A recent experimental study shows that wetted two-grain boundaries are a common feature of partially molten dunite at small melt fractions (Garapic et al., G3, 2013). In early ideal models which assume isotropic surface energy, the grain scale melt distribution is uniquely determined by knowing the melt fraction and the dihedral angle between two crystalline grains and the melt (von Bargen and Waff, JGR, 1986). Olivine is anisotropic in surface energy, hence the grain scale melt distribution at given melt fraction cannot be characterized by the dihedral angle alone. The grain boundary wetness, which is defined as the ratio of solid-liquid boundary area over the total interfacial area (Takei, JGR, 1998), is a more objective measure of the grain scale melt distribution. The aim of this study is to quantify the relationship between grain size, melt fraction, temperature and grain boundary wetness of partially molten dunite under dry conditions. We annealed olivine-basalt aggregates with melt fractions from 0.03% to 6% at a range of temperatures and 1 GPa in a piston cylinder for 1 to 336 hours, with resulting mean grain sizes of 10 to 60 μm. The samples were sectioned, polished and imaged at high resolution by using a field emission SEM. Each image had a size of 2048 x 1536 pixels with a resolution of 0.014 to 0.029 μm/pixel, depending on magnification. For each sample, depending on grain sizes, we made mosaics of 3 x 3 or 6 x 6 overlapping images. Measurements of melt fraction, grain boundary wetness and grain size were carried out on these high resolution mosaics by using ImageJ software. Analyses of mosaics show that grain boundary wetness increases with increasing melt fraction at constant grain size to values well above those

  14. Investigation of a twisted-tube type shell-and-tube heat exchanger

    OpenAIRE

    Danielsen, Sven Olaf

    2009-01-01

    This master thesis investigates twisted tube type shell-and-tube heat exchangers with emphasis on thermal-hydraulic characteristics, fouling and vibration properties. An extensive literature study has been carried out in order to map all published research reports written on the topic. The mapping of performed research shows that the available information is limited.Mathematical correlations for twisted tube thermal-hydraulic characteristics are extracted from the research reports found in th...

  15. The electrochemical reduction processes of solid compounds in high temperature molten salts.

    Science.gov (United States)

    Xiao, Wei; Wang, Dihua

    2014-05-21

    Solid electrode processes fall in the central focus of electrochemistry due to their broad-based applications in electrochemical energy storage/conversion devices, sensors and electrochemical preparation. The electrolytic production of metals, alloys, semiconductors and oxides via the electrochemical reduction of solid compounds (especially solid oxides) in high temperature molten salts has been well demonstrated to be an effective and environmentally friendly process for refractory metal extraction, functional materials preparation as well as spent fuel reprocessing. The (electro)chemical reduction of solid compounds under cathodic polarizations generally accompanies a variety of changes at the cathode/melt electrochemical interface which result in diverse electrolytic products with different compositions, morphologies and microstructures. This report summarizes various (electro)chemical reactions taking place at the compound cathode/melt interface during the electrochemical reduction of solid compounds in molten salts, which mainly include: (1) the direct electro-deoxidation of solid oxides; (2) the deposition of the active metal together with the electrochemical reduction of solid oxides; (3) the electro-inclusion of cations from molten salts; (4) the dissolution-electrodeposition process, and (5) the electron hopping process and carbon deposition with the utilization of carbon-based anodes. The implications of the forenamed cathodic reactions on the energy efficiency, chemical compositions and microstructures of the electrolytic products are also discussed. We hope that a comprehensive understanding of the cathodic processes during the electrochemical reduction of solid compounds in molten salts could form a basis for developing a clean, energy efficient and affordable production process for advanced/engineering materials.

  16. Tube-shape verifier

    Science.gov (United States)

    Anderson, A. N.; Christ, C. R.

    1980-01-01

    Inexpensive apparatus checks accuracy of bent tubes. Assortment of slotted angles and clamps is bolted down to flat aluminum plate outlining shape of standard tube bent to desired configuration. Newly bent tubes are then checked against this outline. Because parts are bolted down, tubes can be checked very rapidly without disturbing outline. One verifier per tube-bending machine can really speed up production in tube-bending shop.

  17. Molten Fuel-Coolant Interactions induced by coolant injection into molten fuel

    Energy Technology Data Exchange (ETDEWEB)

    Park, H.S.; Yamano, Norihiko; Maruyama, Yu; Moriyama, Kiyofumi; Yang, Y.; Sugimoto, Jun [Severe Accident Research Laboratory, Japan Atomic Energy Research Institute, Tokai, Ibaraki (Japan)

    1999-07-01

    To investigate Molten Fuel-Coolant Interactions (MFCIs) in various contact geometries, an experimental program, called MUSE (MUlti-configurations in Steam Explosions), has been initiated under the ALPHA program at JAERI in Japan. The first series of MUSE test has been focused on the coolant injection (CI) and stratified modes of FCIs using water as coolant and molten thermite as molten fuel. The effects of water jet subcooling, jet dynamics, jet shape and system constraint on FCIs energetic in these modes were experimentally investigated by precisely measuring their mechanical energy release in the MUSE facility. It was observed that measured mechanical energy increased with increasing of jet subcooling in a weakly constraint system but decreased in a strongly constraint system. FCI energetic also increased with increasing of water jet velocity. These results suggested that the penetration and dispersion phenomena of a water jet inside a melt determined the mixing conditions of FCIs in these contact modes and consequently played important roles on FCI energetics. To understand fundamental physics of these phenomena and possible mixing conditions in the MUSE tests, a set of visualization tests with several pairs of jet-pool liquids in non-boiling and isothermal conditions were carried out. Numerical simulations of a water jet penetrating into a water pool at non-boiling conditions showed similar behaviors to those observed in the visualization tests. (author)

  18. Castable cements to prevent corrosion of metals in molten salts

    Energy Technology Data Exchange (ETDEWEB)

    Gomez-Vidal, J. C.; Morton, E.

    2016-08-01

    Castable cements on metals form a protective barrier that is able to prevent permeation of molten salts towards metallic surfaces. Silica-based castable cements are capable of protecting containment metallic alloys from the corrosive attack of molten chlorides at temperatures as high as 650 degrees C. Boron nitride (BN) blocking the pores in the cured cement prevents permeation of the molten chloride towards the metal surface. The cements tested are not chemically stable in molten carbonates, because the bonding components dissolved into molten carbonates salt. The corrosion rate is 7.72+/-0.32 mm/year for bare stainless steel 347 in molten eutectic NaCl - 65.58 wt% LiCl at 650 degrees C, which is the baseline used for determining how well the cement protects the metallic surfaces from corrosion. In particular the metal fully encapsulated with Aremco 645-N with pores filled with boron nitride immersed in molten eutectic NaCl - 65.58 wt% LiCl at 650 degrees C shows a corrosion rate of 9E-04 mm/year. The present study gives initial corrosion rates. Long-term tests are required to determine if Aremco 645-N with BN coating on metal has long term chemical stability for blocking salt permeation through coating pores.

  19. Molten Composition B Viscosity at Elevated Temperature

    Science.gov (United States)

    Zerkle, David K.; Núñez, Marcel P.; Zucker, Jonathan M.

    2016-10-01

    A shear-thinning viscosity model is developed for molten Composition B at elevated temperature from analysis of falling ball viscometer data. Results are reported with the system held at 85, 110, and 135°C. Balls of densities of 2.7, 8.0, and 15.6 g/cm3 are dropped to generate a range of strain rates in the material. Analysis of video recordings gives the speed at which the balls fall. Computer simulation of the viscometer is used to determine parameters for a non-Newtonian model calibrated to measured speeds. For the first time, viscosity is shown to be a function of temperature and strain rate-dependent maximum RDX (cyclotrimethylenetrinitramine) particle volume fraction.

  20. Numerical tools for Molten salt reactor simulation

    Energy Technology Data Exchange (ETDEWEB)

    Doligez, X.; Heuer, D.; Merle-Lucotte, E.; Allibert, M.; Ghetta, V. [LPSC-IN2P3-CNRS/Universite Joseph Fourier/Grenoble-INP, 53 Avenue des Martyrs, 38026 Grenoble Cedex (France)

    2009-06-15

    Molten salt reactors (MSR) are basically different from other reactors mainly because the fuel is liquid. It flows through the core, pipes, pumps and heat exchangers. Previous studies showed that a particular configuration of a molten salt reactor perfectly fulfils criteria chosen by the Generation 4 International Forum (GIF). This configuration, called non-moderated Thorium Molten Salt Reactor is a 1000 GW electrical thorium cycle based molten salt reactor with no moderator inside the core. Consequently, the neutron spectrum is fast. The reactor is coupled with a salt control unit, which complicates the studies. Reactors simulation is based on resolving Bateman's equations, which give the population of each nucleus inside the core at each moment. Because of MSR's fundamental characteristics, those equations have to be modified adding two terms: a fertile/fissile alimentation for the reactivity and the salt composition control, and the reprocessing associated term. Equations become: {delta}N{sub i}/{delta}t = {sigma}{sub j{ne}}{sub i} {lambda}{sub j{yields}}{sub i} N{sub j} + X{sub j} <{sigma}{sub j}{phi}> N{sub j} - {lambda}{sub i}N{sub i} - <{sigma}{sub i}{phi}> N{sub i} {lambda}{sub chem} N{sub i} + A where {lambda}{sub chem} represents the reprocessing capacities and A represents the fertile/fissile alimentation. All our studies are made with a homemade code, REM, which is a precision driven code for material evolution. Neutron flux and neutron reactions rate are calculated thanks MCNP and the temporal integration is made thanks a Runge-Kutta fourth order method. This code REM, whose calculation scheme will be described in the paper, does not allow a coupling flexible enough between the reprocessing and the core physics. Indeed, reprocessing terms in the previous equation ({lambda}{sub chem}) are set for the whole evolution that can last several hundreds of years. A new way is to drive chemical needs to keep the core critical. Therefore, we are

  1. Modelisation of the SECMin molten salts environment

    Science.gov (United States)

    Lucas, M.; Slim, C.; Delpech, S.; di Caprio, D.; Stafiej, J.

    2014-06-01

    We develop a cellular automata modelisation of SECM experiments to study corrosion in molten salt media for generation IV nuclear reactors. The electrodes used in these experiments are cylindrical glass tips with a coaxial metal wire inside. As the result of simulations we obtain the current approach curves of the electrodes with geometries characterized by several values of the ratios of glass to metal area at the tip. We compare these results with predictions of the known analytic expressions, solutions of partial differential equations for flat uniform geometry of the substrate. We present the results for other, more complicated substrate surface geometries e. g. regular saw modulated surface, surface obtained by Eden model process, ...

  2. Molten salts database for energy applications

    CERN Document Server

    Serrano-López, Roberto; Cuesta-López, Santiago

    2013-01-01

    The growing interest in energy applications of molten salts is justified by several of their properties. Their possibilities of usage as a coolant, heat transfer fluid or heat storage substrate, require thermo-hydrodynamic refined calculations. Many researchers are using simulation techniques, such as Computational Fluid Dynamics (CFD) for their projects or conceptual designs. The aim of this work is providing a review of basic properties (density, viscosity, thermal conductivity and heat capacity) of the most common and referred salt mixtures. After checking data, tabulated and graphical outputs are given in order to offer the most suitable available values to be used as input parameters for other calculations or simulations. The reviewed values show a general scattering in characterization, mainly in thermal properties. This disagreement suggests that, in several cases, new studies must be started (and even new measurement techniques should be developed) to obtain accurate values.

  3. Molten-Salt Depleted-Uranium Reactor

    CERN Document Server

    Dong, Bao-Guo; Gu, Ji-Yuan

    2015-01-01

    The supercritical, reactor core melting and nuclear fuel leaking accidents have troubled fission reactors for decades, and greatly limit their extensive applications. Now these troubles are still open. Here we first show a possible perfect reactor, Molten-Salt Depleted-Uranium Reactor which is no above accident trouble. We found this reactor could be realized in practical applications in terms of all of the scientific principle, principle of operation, technology, and engineering. Our results demonstrate how these reactors can possess and realize extraordinary excellent characteristics, no prompt critical, long-term safe and stable operation with negative feedback, closed uranium-plutonium cycle chain within the vessel, normal operation only with depleted-uranium, and depleted-uranium high burnup in reality, to realize with fission nuclear energy sufficiently satisfying humanity long-term energy resource needs, as well as thoroughly solve the challenges of nuclear criticality safety, uranium resource insuffic...

  4. Energetic materials destruction using molten salt

    Energy Technology Data Exchange (ETDEWEB)

    Upadhye, R.S.; Watkins, B.E.; Pruneda, C.O.; Brummond, W.A.

    1994-04-29

    The Lawrence Livermore National Laboratory in conjunction with the Energetic Materials Center is developing methods for the safe and environmentally sound destruction of explosives and propellants as a part of the Laboratory`s ancillary demilitarization mission. LLNL has built a small-scale unit to test the destruction of HE using the Molten Salt Destruction (MSD) Process. In addition to the high explosive HMX, destruction has been carried out on RDX, PETN, ammonium picrate, TNT, nitroguanadine, and TATB. Also destroyed was a liquid gun propellant comprising hydroxyammonium nitrate, triethanolammonium nitrate and water. In addition to these pure components, destruction has been carried out on a number of commonly used formulations, such as LX-10, LX-16, LX-17, and PBX-9404.

  5. Fast Spectrum Molten Salt Reactor Options

    Energy Technology Data Exchange (ETDEWEB)

    Gehin, Jess C [ORNL; Holcomb, David Eugene [ORNL; Flanagan, George F [ORNL; Patton, Bruce W [ORNL; Howard, Rob L [ORNL; Harrison, Thomas J [ORNL

    2011-07-01

    During 2010, fast-spectrum molten-salt reactors (FS-MSRs) were selected as a transformational reactor concept for light-water reactor (LWR)-derived heavy actinide disposition by the Department of Energy-Nuclear Energy Advanced Reactor Concepts (ARC) program and were the subject of a preliminary scoping investigation. Much of the reactor description information presented in this report derives from the preliminary studies performed for the ARC project. This report, however, has a somewhat broader scope-providing a conceptual overview of the characteristics and design options for FS-MSRs. It does not present in-depth evaluation of any FS-MSR particular characteristic, but instead provides an overview of all of the major reactor system technologies and characteristics, including the technology developments since the end of major molten salt reactor (MSR) development efforts in the 1970s. This report first presents a historical overview of the FS-MSR technology and describes the innovative characteristics of an FS-MSR. Next, it provides an overview of possible reactor configurations. The following design features/options and performance considerations are described including: (1) reactor salt options-both chloride and fluoride salts; (2) the impact of changing the carrier salt and actinide concentration on conversion ratio; (3) the conversion ratio; (4) an overview of the fuel salt chemical processing; (5) potential power cycles and hydrogen production options; and (6) overview of the performance characteristics of FS-MSRs, including general comparative metrics with LWRs. The conceptual-level evaluation includes resource sustainability, proliferation resistance, economics, and safety. The report concludes with a description of the work necessary to begin more detailed evaluation of FS-MSRs as a realistic reactor and fuel cycle option.

  6. Stable colloids in molten inorganic salts

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Hao; Dasbiswas, Kinjal; Ludwig, Nicholas B.; Han, Gang; Lee, Byeongdu; Vaikuntanathan, Suri; Talapin, Dimitri V.

    2017-02-16

    A colloidal solution is a homogeneous dispersion of particles or droplets of one phase (solute) in a second, typically liquid, phase (solvent). Colloids are ubiquitous in biological, chemical and technological processes1, 2, homogenizing highly dissimilar constituents. To stabilize a colloidal system against coalescence and aggregation, the surface of each solute particle is engineered to impose repulsive forces strong enough to overpower van der Waals attraction and keep the particles separated from each other2. Electrostatic stabilization3, 4 of charged solutes works well in solvents with high dielectric constants, such as water (dielectric constant of 80). In contrast, colloidal stabilization in solvents with low polarity, such as hexane (dielectric constant of about 2), can be achieved by decorating the surface of each particle of the solute with molecules (surfactants) containing flexible, brush-like chains2, 5. Here we report a class of colloidal systems in which solute particles (including metals, semiconductors and magnetic materials) form stable colloids in various molten inorganic salts. The stability of such colloids cannot be explained by traditional electrostatic and steric mechanisms. Screening of many solute–solvent combinations shows that colloidal stability can be traced to the strength of chemical bonding at the solute–solvent interface. Theoretical analysis and molecular dynamics modelling suggest that a layer of surface-bound solvent ions produces long-ranged charge-density oscillations in the molten salt around solute particles, preventing their aggregation. Colloids composed of inorganic particles in inorganic melts offer opportunities for introducing colloidal techniques to solid-state science and engineering applications.

  7. Molten carbonate fuel cell technology improvement

    Energy Technology Data Exchange (ETDEWEB)

    1991-06-01

    This report summarizes the work performed under Department of Energy Contract DEAC21-87MC23270, Molten Carbonate Fuel Cell Technology Improvement.'' This work was conducted over a three year period and consisted of three major efforts. The first major effort was the power plant system study which reviewed the competitive requirements for a coal gasifier/molten carbonate fuel cell power plant, produced a conceptual design of a CG/MCFC, and defined the technology development requirements. This effort is discussed in Section 1 of the report. The second major effort involved the design and development of a new MCFC cell configuration which reduced the material content of the cell to a level competitive with competing power plants, simplified the cell configuration to make the components more manufacturable and adaptable to continuous low cost processing techniques, and introduced new-low-pressure drop flow fields for both reactant gases. The new flow fields permitted the incorporation of recirculation systems in both reactant gas systems, permitting simplified cooling techniques and the ability to operate on both natural gas and a wide variety of gasifier fuels. This cell technology improvement is discussed in Section 2. The third major effort involved the scaleup of the new cell configuration to the full-area, 8-sq-ft size and resulted in components used for a 25-kW, 20-cell stack verification test. The verification test was completed with a run of 2200 hours, exceeding the goal of 2000 hours and verifying the new cell design. TWs test, in turn, provided the confidence to proceed to a 100-kW demonstration which is the goal of the subsequent DOE program. The scaleup and stack verification tests are discussed in Sections 3, 4, 5, and 6 of this report.

  8. Thermo-mechanical and optical optimization of the molten salt receiver for a given heliostat field

    Science.gov (United States)

    Augsburger, Germain; Das, Apurba K.; Boschek, Erik; Clark, Michael M.

    2016-05-01

    The tower type molten salt solar thermal power plant has proven to be advantageous over other utility scale solar power plant configurations due to its scalability and provision of storage, thereby improving the dispatchability. The configuration consists of a molten salt central receiver (MSCR) located atop an optimally located tower within a heliostat field with thousands of mirrors. The MSCR receives the concentrated energy from the heliostat field which heats a molten salt heat transfer fluid for thermal storage and utilization in producing steam as and when required for power generation. The MSCR heat transfer surface consists of banks of tangent tubes arranged in panels. The combined cost of the heliostat field and the receiver is 40%-50% of the total plant cost, which calls for optimization to maximize their utilization. Several previous studies have looked into the optimum solar power plant size based on various site conditions. However, the combined optimization of the receiver and the heliostat field has not been reported before. This study looks into the optimum configuration of the receiver for a given heliostat field. An in-house tool has been developed to select and rank a few receiver surface configurations (typically <50) from a list of hundreds of thousands of possible options. The operating limits which the heliostat field needs to obey are defined for the ranked surface configurations based on several different design considerations (e.g. mechanical integrity, corrosion limits). The thermal output of the receiver configurations for a given heliostat field is maximized. A combined rank indicating the optimum configurations in descending order of preference is presented based on the performance and various other practical considerations (e.g. total surface area, cost of material, ability of aiming strategies to distribute the flux). The methodology thus provided can be used as a guideline to arrive at an optimum receiver configuration for a given

  9. Freezing in a vertical tube

    Energy Technology Data Exchange (ETDEWEB)

    Sparrow, E.M.; Broadbent, J.A.

    1983-05-01

    Fundamental heat transfer experiments were performed for freezing of an initially superheated or nonsuperheated liquid in a cooled vertical tube. Measurements were made which yielded information about the freezing front and the frozen mass, about the various energy components extracted from the tube, and about the decay of the initial liquid superheat. Four component energies were identified and evaluated from the experimental data, including the latent energy released by the phase change and sensibly energies released from the subcooled frozen solid and the superheated liquid. Initial superheating of the liquid tended to moderately diminish the frozen mass and latent energy extraction at short freezing times but had little effect on these quantitites at longer times. The extracted sensible energies associated with the superheating more than compensated for the aforementioned decrease in the latent energy. Although the latent energy is the largest contributor to the total extracted energy, the aggregate sensible energies can make a significant contribution, especially at large tube wall subcooling, large initial liquid superheating, and short freezing time. Natural convection effects in the superheated liquid were modest and were confined to short freezing times.

  10. Apparatus and method for stripping tritium from molten salt

    Energy Technology Data Exchange (ETDEWEB)

    Holcomb, David E.; Wilson, Dane F.

    2017-02-07

    A method of stripping tritium from flowing stream of molten salt includes providing a tritium-separating membrane structure having a porous support, a nanoporous structural metal-ion diffusion barrier layer, and a gas-tight, nonporous palladium-bearing separative layer, directing the flowing stream of molten salt into contact with the palladium-bearing layer so that tritium contained within the molten salt is transported through the tritium-separating membrane structure, and contacting a sweep gas with the porous support for collecting the tritium.

  11. A Possible Regenerative, Molten-Salt, Thermoelectric Fuel Cell

    Science.gov (United States)

    Greenberg, Jacob; Thaller, Lawrence H.; Weber, Donald E.

    1964-01-01

    Molten or fused salts have been evaluated as possible thermoelectric materials because of the relatively good values of their figures of merit, their chemical stability, their long liquid range, and their ability to operate in conjunction with a nuclear reactor to produce heat. In general, molten salts are electrolytic conductors; therefore, there will be a transport of materials and subsequent decomposition with the passage of an electric current. It is possible nonetheless to overcome this disadvantage by using the decomposition products of the molten-salt electrolyte in a fuel cell. The combination of a thermoelectric converter and a fuel cell would lead to a regenerative system that may be useful.

  12. Apparatus and method for stripping tritium from molten salt

    Science.gov (United States)

    Holcomb, David E.; Wilson, Dane F.

    2017-02-07

    A method of stripping tritium from flowing stream of molten salt includes providing a tritium-separating membrane structure having a porous support, a nanoporous structural metal-ion diffusion barrier layer, and a gas-tight, nonporous palladium-bearing separative layer, directing the flowing stream of molten salt into contact with the palladium-bearing layer so that tritium contained within the molten salt is transported through the tritium-separating membrane structure, and contacting a sweep gas with the porous support for collecting the tritium.

  13. Control strategies in a thermal oil - Molten salt heat exchanger

    Science.gov (United States)

    Roca, Lidia; Bonilla, Javier; Rodríguez-García, Margarita M.; Palenzuela, Patricia; de la Calle, Alberto; Valenzuela, Loreto

    2016-05-01

    This paper presents a preliminary control scheme for a molten salt - thermal oil heat exchanger. This controller regulates the molten salt mass flow rate to reach and maintain the desired thermal oil temperature at the outlet of the heat exchanger. The controller architecture has been tested using an object-oriented heat exchanger model that has been validated with data from a molten salt testing facility located at CIEMAT-PSA. Different simulations are presented with three different goals: i) to analyze the controller response in the presence of disturbances, ii) to demonstrate the benefits of designing a setpoint generator and iii) to show the controller potential against electricity price variations.

  14. Equilibrium distribution of actinides including Cm between molten LiCl-KCl eutectic and liquid cadmium

    Energy Technology Data Exchange (ETDEWEB)

    Koyama, T.; Kinoshita, K.; Inoue, T. [Central Research Inst. of Electric Power Industry, Tokyo (Japan); Ougier, M.; Malmbeck, R.; Glatz, J.P. [Joint Research Centre, Karlsruhe (Germany). Inst. for Transuranium Elements

    2008-07-01

    Equilibrium distribution of actinides both in molten LiCl-KCl eutectic and liquid cadmium were measured from the concentration data obtained in electrorefining tests and reductive extraction tests. Separation factors for U, Np, Am, Cm against Pu were derived in the practical temperature range of 700 K to 783 K. The derived separation factors are consistent with the reported values measured at 773 K and 723 K. The temperature dependence for Cm is different compared to the other actinides (U, Np and Am). This behavior remains unclear and additional experimental measurements of distribution coefficient of Cm are required before ruling on the real behavior. (orig.)

  15. Development of a solar thermal central heat receiver using molten salt

    Science.gov (United States)

    Tracey, T. R.

    1981-06-01

    The development and test of a 5 MWth solar heat receiver using a molten nitrate salt (60 percent NaNO3, 40 percent KNaNO3) as the heat transfer fluid is described. The application of the receiver concept in a central receiver solar power system is explained. The advantages of using molten nitrate salts as the receiver heat transfer fluid and the storage fluid are discussed. The problems associated with the receiver development including the need for high temperatures and combinations of creep and fatigue in the receiver tubes are discussed. Our approach to scaling from the 5 MWth test receiver to commercial receivers in the range of 200 MWth to 500 MWth is defined. The 5 MWth test system is described including the instrumentation used. The test facility which has a 60 m tower and 222 heliostats is described. The test results are presented. The receiver was in test for 500 hr at temperature and heat flux levels expected in commercial receiver systems.

  16. Erosion Effect of Molten Steel on Carbon Containing Refractories for Continuous Casting

    Institute of Scientific and Technical Information of China (English)

    LI Hongxia; YANG Bin; LIU Guoqi; CHENG Hepeng

    2007-01-01

    The erosion resistance of carbon containing refractories for continuous casting to molten steel was investigated by means of simulative erosion test and examining used refractories.Decolonization and reaction between molten steel and decolonization layer are main erosion process of carbon containing refractories by1 molten steel.The reactions between molten steel and oxide in refractories determine the thickness of decarbonization layer A dense layer formation on the working surface contacting with molten steel during casting will suppress decarbonization and erosion process.

  17. Abstract: The Reaction between MoO3 and Molten K2S2O7 forming K2MoO2(SO4)2

    DEFF Research Database (Denmark)

    Nørbygaard, Thomas; Berg, Rolf W.; Nielsen, Kurt

    1998-01-01

    The present work is part of a general study on metal ore extraction by a pyrosulfate melting process. We report on the formation and structure of colorless crystals, which were prepared by dissolving molybdenum trioxide in molten potassium pyrosulfate at 430 degrees C....

  18. Surface tension of molten tin investigated with sessile drop method

    Institute of Scientific and Technical Information of China (English)

    LI Jing; YUAN Zhang-fu; FAN Jian-feng; KE Jia-jun

    2005-01-01

    The surface tension of molten tin was determined by a set of self-developed digital equipment with sessile drop method at oxygen partial pressure of 1.0 × 10-6 MPa under different temperatures, and the dependence of surface tension of molten tin on temperature was also discussed. The emphasis was placed on the comparison of surface tension of the same molten tin sample measured by using different equipments with sessile drop method. Results of the comparison indicate that the measurement results with sessile drop method under the approximate experimental conditions are coincident, and the self-developed digital equipment for surface tension measurement has higher stability and accuracy. The relationships of surface tension of molten tin and its temperature coefficient with temperature and oxygen partial pressure were also elucidated from the thermodynamic equilibrium analysis.

  19. Large Scale Inert Anode for Molten Oxide Electrolysis Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Molten oxide electrolysis is a demonstrated laboratory-scale process for producing oxygen from the JSC-1a lunar simulant; however, critical subsystems necessary for...

  20. High Surface Iridium Anodes for Molten Oxide Electrolysis Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Processing of lunar regolith into oxygen for habitat and propulsion is needed to support future space missions. Direct electrochemical reduction of molten regolith...

  1. Segregation of Molten Salt on Chromizing in Thermal Diffusion Process

    Institute of Scientific and Technical Information of China (English)

    WANG Hongfu; WANG Junyuan; WANG Huachang

    2011-01-01

    The segregation of thermal diffusion salt bath chromizing process was analyzed.The experimental chromizing ingredients were prepared by the four groups A,B,C,and D.In order to study the segregation status of this case,the cooling molten salt in the crucible was removed by drilling from the heart core of molten salt.The core of molten salt was analyzed by X-ray fluorescence spectroscopy and XRD.Through the analysis,we can conclude that the Cr element deposited in the bottom was 4.51 times than the top.Chloride added to the molten salt will reduce segregation.Meantime we proposed some measures to overcome the segregation problem.

  2. Polymers' surface interactions with molten iron: A theoretical study

    Science.gov (United States)

    Assadi, M. Hussein N.; Sahajwalla, Veena

    2014-10-01

    Environmental concerns are the chief drive for more innovative recycling techniques for end-of-life polymeric products. One attractive option is taking advantage of C and H content of polymeric waste in steelmaking industry. In this work, we examined the interaction of two high production polymers i.e. polyurethane and polysulfide with molten iron using ab initio molecular dynamics simulation. We demonstrate that both polymers can be used as carburizers for molten iron. Additionally, we found that light weight H2 and CHx molecules were released as by-products of the polymer-molten iron interaction. The outcomes of this study will have applications in the carburization of molten iron during ladle metallurgy and waste plastic injection in electric arc furnace.

  3. Density and Structure Analysis of Molten Ni-W Alloys

    Institute of Scientific and Technical Information of China (English)

    Feng XIAO; Liang FANG

    2004-01-01

    Density of molten Ni and Ni-W alloys was measured in the temperature range of 1773~1873 K with a sessile drop method.The density of molten Ni and Ni-W alloys trends to decrease with increasing temperature. The density and molar volume of the alloys trend to increase with increasing W concentration in the alloys. The calculation result shows an ideal mixing of Ni-W alloys.

  4. Molten fluoride mixtures as possible fission reactor fuels

    Energy Technology Data Exchange (ETDEWEB)

    Grimes, W.R.

    1978-01-01

    Molten mixtures of fluorides with UF/sub 4/ as a component have been used as combined fuel and primary heat transfer agent in experimental high-temperature reactors and have been proposed for use in breeders or converters of /sup 233/U from thorium. Such use places stringent and diverse demands upon the fluid fuel. A brief review of chemical behavior of molten fluorides is given to show some of their strengths and weaknesses for such service.

  5. Minimizing the fissile inventory of the molten salt fast reactor

    OpenAIRE

    Merle-Lucotte, E.; Heuer, D.; Allibert, M.; Doligez, X.; Ghetta, V.

    2009-01-01

    International audience; Molten salt reactors in the configurations presented here, called Molten Salt Fast Reactors (MSFR), have been selected for further studies by the Generation IV International Forum. These reactors may be operated in simplified and safe conditions in the Th/233U fuel cycle with fluoride salts. We present here the concept, before focusing on a possible optimization in term of minimization of the initial fissile inventory. Our studies demonstrate that an inventory of 233U ...

  6. Thermodynamic characterization of salt components for Molten Salt Reactor fuel

    OpenAIRE

    Capelli, E.

    2016-01-01

    The Molten Salt Reactor (MSR) is a promising future nuclear fission reactor technology with excellent performance in terms of safety and reliability, sustainability, proliferation resistance and economics. For the design and safety assessment of this concept, it is extremely important to have a thorough knowledge of the physico-chemical properties of molten fluorides salts, which are one of the best options for the reactor fuel. This dissertation presents the thermodynamic description of the ...

  7. Novel waste printed circuit board recycling process with molten salt.

    Science.gov (United States)

    Riedewald, Frank; Sousa-Gallagher, Maria

    2015-01-01

    The objective of the method was to prove the concept of a novel waste PCBs recycling process which uses inert, stable molten salts as the direct heat transfer fluid and, simultaneously, uses this molten salt to separate the metal products in either liquid (solder, zinc, tin, lead, etc.) or solid (copper, gold, steel, palladium, etc.) form at the operating temperatures of 450-470 °C. The PCB recovery reactor is essentially a U-shaped reactor with the molten salt providing a continuous fluid, allowing molten salt access from different depths for metal recovery. A laboratory scale batch reactor was constructed using 316L as suitable construction material. For safety reasons, the inert, stable LiCl-KCl molten salts were used as direct heat transfer fluid. Recovered materials were washed with hot water to remove residual salt before metal recovery assessment. The impact of this work was to show metal separation using molten salts in one single unit, by using this novel reactor methodology. •The reactor is a U-shaped reactor filled with a continuous liquid with a sloped bottom representing a novel reactor concept.•This method uses large PCB pieces instead of shredded PCBs as the reactor volume is 2.2 L.•The treated PCBs can be removed via leg B while the process is on-going.

  8. Determination of diffusion coefficients of hydrogen and deuterium in Zr-2.5%Nb pressure tube material using hot vacuum extraction-quadrupole mass spectrometry

    Science.gov (United States)

    Shrivastava, Komal Chandra; Kulkarni, A. S.; Ramanjaneyulu, P. S.; Sunil, Saurav; Saxena, M. K.; Singh, R. N.; Tomar, B. S.; Ramakumar, K. L.

    2015-06-01

    The diffusion coefficients of hydrogen and deuterium in Zr-2.5%Nb alloy were measured in the temperature range 523 to 673 K, employing hot vacuum extraction-quadrupole mass spectrometry (HVE-QMS). One end of the Zr-2.5%Nb alloy specimens was charged electrolytically with the desired hydrogen isotope. After annealing at different temperatures for a predetermined time, the specimens were cut into thin slices, which were analyzed for their H2/D2 content using the HVE-QMS technique. The depth profile data were fitted into the equation representing the solution of Fick's second law of diffusion. The activation energy of hydrogen/deuterium diffusion was obtained from the Arrhenius relation between the diffusion coefficient and temperature. The temperature dependent diffusion coefficient can be represented as DH = 1.41 × 10-7 exp(-36,000/RT) and DD = 6.16 × 10-8 exp(-35,262/RT) for hydrogen and deuterium, respectively.

  9. Determination of diffusion coefficients of hydrogen and deuterium in Zr–2.5%Nb pressure tube material using hot vacuum extraction-quadrupole mass spectrometry

    Energy Technology Data Exchange (ETDEWEB)

    Shrivastava, Komal Chandra, E-mail: komal@barc.gov.in [Radioanalytical Chemistry Division, Bhabha Atomic Research Centre, Mumbai 400 085 (India); Kulkarni, A.S.; Ramanjaneyulu, P.S. [Radioanalytical Chemistry Division, Bhabha Atomic Research Centre, Mumbai 400 085 (India); Sunil, Saurav [Mechanical Metallurgy Division, Bhabha Atomic Research Centre, Mumbai 400 085 (India); Saxena, M.K. [Radioanalytical Chemistry Division, Bhabha Atomic Research Centre, Mumbai 400 085 (India); Singh, R.N. [Mechanical Metallurgy Division, Bhabha Atomic Research Centre, Mumbai 400 085 (India); Tomar, B.S.; Ramakumar, K.L. [Radioanalytical Chemistry Division, Bhabha Atomic Research Centre, Mumbai 400 085 (India)

    2015-06-15

    The diffusion coefficients of hydrogen and deuterium in Zr–2.5%Nb alloy were measured in the temperature range 523 to 673 K, employing hot vacuum extraction-quadrupole mass spectrometry (HVE-QMS). One end of the Zr–2.5%Nb alloy specimens was charged electrolytically with the desired hydrogen isotope. After annealing at different temperatures for a predetermined time, the specimens were cut into thin slices, which were analyzed for their H{sub 2}/D{sub 2} content using the HVE-QMS technique. The depth profile data were fitted into the equation representing the solution of Fick’s second law of diffusion. The activation energy of hydrogen/deuterium diffusion was obtained from the Arrhenius relation between the diffusion coefficient and temperature. The temperature dependent diffusion coefficient can be represented as D{sub H} = 1.41 × 10{sup −7} exp(−36,000/RT) and D{sub D} = 6.16 × 10{sup −8} exp(−35,262/RT) for hydrogen and deuterium, respectively.

  10. Next-Generation Electrochemical Energy Materials for Intermediate Temperature Molten Oxide Fuel Cells and Ion Transport Molten Oxide Membranes.

    Science.gov (United States)

    Belousov, Valery V

    2017-02-21

    High temperature electrochemical devices such as solid oxide fuel cells (SOFCs) and oxygen separators based on ceramic materials are used for efficient energy conversion. These devices generally operate in the temperature range of 800-1000 °C. The high operating temperatures lead to accelerated degradation of the SOFC and oxygen separator materials. To solve this problem, the operating temperatures of these electrochemical devices must be lowered. However, lowering the temperature is accompanied by decreasing the ionic conductivity of fuel cell electrolyte and oxygen separator membrane. Therefore, there is a need to search for alternative electrolyte and membrane materials that have high ionic conductivity at lower temperatures. A great many opportunities exist for molten oxides as electrochemical energy materials. Because of their unique electrochemical properties, the molten oxide innovations can offer significant benefits for improving energy efficiency. In particular, the newly developed electrochemical molten oxide materials show high ionic conductivities at intermediate temperatures (600-800 °C) and could be used in molten oxide fuel cells (MOFCs) and molten oxide membranes (MOMs). The molten oxide materials containing both solid grains and liquid channels at the grain boundaries have advantages compared to the ceramic materials. For example, the molten oxide materials are ductile, which solves a problem of thermal incompatibility (difference in coefficient of thermal expansion, CTE). Besides, the outstanding oxygen selectivity of MOM materials allows us to separate ultrahigh purity oxygen from air. For their part, the MOFC electrolytes show the highest ionic conductivity at intermediate temperatures. To evaluate the potential of molten oxide materials for technological applications, the relationship between the microstructure of these materials and their transport and mechanical properties must be revealed. This Account summarizes the latest results on

  11. Molten metal reactor and method of forming hydrogen, carbon monoxide and carbon dioxide using the molten alkaline metal reactor

    Science.gov (United States)

    Bingham, Dennis N.; Klingler, Kerry M.; Turner, Terry D.; Wilding, Bruce M.

    2012-11-13

    A molten metal reactor for converting a carbon material and steam into a gas comprising hydrogen, carbon monoxide, and carbon dioxide is disclosed. The reactor includes an interior crucible having a portion contained within an exterior crucible. The interior crucible includes an inlet and an outlet; the outlet leads to the exterior crucible and may comprise a diffuser. The exterior crucible may contain a molten alkaline metal compound. Contained between the exterior crucible and the interior crucible is at least one baffle.

  12. Molten Salt Breeder Reactor Analysis Methods

    Energy Technology Data Exchange (ETDEWEB)

    Park, Jinsu; Jeong, Yongjin; Lee, Deokjung [Ulsan National Institute of Science and Technology, Ulsan (Korea, Republic of)

    2015-05-15

    Utilizing the uranium-thorium fuel cycle shows considerable potential for the possibility of MSR. The concept of MSBR should be revised because of molten salt reactor's advantage such as outstanding neutron economy, possibility of continuous online reprocessing and refueling, a high level of inherent safety, and economic benefit by keeping off the fuel fabrication process. For the development of MSR research, this paper provides the MSBR single-cell, two-cell and whole core model for computer code input, and several calculation results including depletion calculation of each models. The calculations are carried out by using MCNP6, a Monte Carlo computer code, which has CINDER90 for depletion calculation using ENDF-VII nuclear data. From the calculation results of various reactor design parameters, the temperature coefficients are all negative at the initial state and MTC becomes positive at the equilibrium state. From the results of core rod worth, the graphite control rod alone cannot makes the core subcritical at initial state. But the equilibrium state, the core can be made subcritical state only by graphite control rods. Through the comparison of the results of each models, the two-cell method can represent the MSBR core model more accurately with a little more computational resources than the single-cell method. Many of the thermal spectrum MSR have adopted a multi-region single-fluid strategy.

  13. Evaporation of Molten Salts by Plasma Torch

    Science.gov (United States)

    Putvinski, S.; Agnew, S. F.; Chamberlain, F.; Freeman, R. L.; Litvak, A.; Meekins, M.; Schwedock, T.; Umstadter, K. R.; Yung, S.; Bakharev, V.; Dresvin, S.; Egorov, S.; Feygenson, O.; Gabdullin, P.; Ivanov; Kizevetter, D.; Kostrukov, A.; Kuteev, B.; Malugin, V.; Zverev, S.

    2003-10-01

    Archimedes Technology Group is developing a plasma nuclear waste separation technology, called the Plasma Mass Filter. The experimental results on thermal evaporation of molten NaOH based surrogates for the Filter are presented. The main goal of the experiments was the study of high-density plasma discharges in NaOH vapor with the aim to minimize injection of additional working gas in the plasma torch. In these experiments NaOH vapor has been produced either by evaporation of the melt from a crucible introduced inside the plasma torch, or by injection of the melt droplets inside the torch. In the latter case, the melt was first atomized by an ultrasonic nebulizer at a flow rate of up to 2g/s with a droplet size of ˜50um. Plasma composition has been monitored by optical measurements. An optical diagnostic for droplet size measurement is presented together with results of the measurements of the size spectrum of the NaOH droplets.

  14. Effects assessment of 10 functioning years on the main components of the molten salt PCS experimental facility of ENEA

    Science.gov (United States)

    Gaggioli, Walter; Di Ascenzi, Primo; Rinaldi, Luca; Tarquini, Pietro; Fabrizi, Fabrizio

    2016-05-01

    In the frame of the Solar Thermodynamic Laboratory, ENEA has improved CSP Parabolic Trough technologies by adopting new advanced solutions for linear tube receivers and by implementing a binary mixture of molten salt (60% NaNO3 and 40% KNO3) [1] as both heat transfer fluid and heat storage medium in solar field and in storage tanks, thus allowing the solar plants to operate at high temperatures up to 550°C. Further improvements have regarded parabolic mirror collectors, piping and process instrumentation. All the innovative components developed by ENEA, together with other standard parts of the plant, have been tested and qualified under actual solar operating conditions on the PCS experimental facility at the ENEA Casaccia Research Center in Rome (Italy). The PCS (Prova Collettori Solari, i.e. Test of Solar Collectors) facility is the main testing loop built by ENEA and it is unique in the world for what concerns the high operating temperature and the fluid used (mixture of molten salt). It consists in one line of parabolic trough collectors (test section of 100 m long life-size solar collectors) using, as heat transfer fluid, the aforesaid binary mixture of molten salt up to 10 bar, at high temperature in the range 270° and 550°C and a flow rate up to 6.5 kg/s. It has been working since early 2004 [2] till now; it consists in a unique closed loop, and it is totally instrumented. In this paper the effects of over ten years qualification tests on the pressurized tank will be presented, together with the characterization of the thermal losses of the piping of the molten salt circuit, and some observations performed on the PCS facility during its first ten years of operation.

  15. An assessment of the liquid-gas partitioning behavior of major wastewater odorants using two comparative experimental approaches: liquid sample-based vaporization vs. impinger-based dynamic headspace extraction into sorbent tubes.

    Science.gov (United States)

    Iqbal, Mohammad Asif; Kim, Ki-Hyun; Szulejko, Jan E; Cho, Jinwoo

    2014-01-01

    The gas-liquid partitioning behavior of major odorants (acetic acid, propionic acid, isobutyric acid, n-butyric acid, i-valeric acid, n-valeric acid, hexanoic acid, phenol, p-cresol, indole, skatole, and toluene (as a reference)) commonly found in microbially digested wastewaters was investigated by two experimental approaches. Firstly, a simple vaporization method was applied to measure the target odorants dissolved in liquid samples with the aid of sorbent tube/thermal desorption/gas chromatography/mass spectrometry. As an alternative method, an impinger-based dynamic headspace sampling method was also explored to measure the partitioning of target odorants between the gas and liquid phases with the same detection system. The relative extraction efficiency (in percent) of the odorants by dynamic headspace sampling was estimated against the calibration results derived by the vaporization method. Finally, the concentrations of the major odorants in real digested wastewater samples were also analyzed using both analytical approaches. Through a parallel application of the two experimental methods, we intended to develop an experimental approach to be able to assess the liquid-to-gas phase partitioning behavior of major odorants in a complex wastewater system. The relative sensitivity of the two methods expressed in terms of response factor ratios (RFvap/RFimp) of liquid standard calibration between vaporization and impinger-based calibrations varied widely from 981 (skatole) to 6,022 (acetic acid). Comparison of this relative sensitivity thus highlights the rather low extraction efficiency of the highly soluble and more acidic odorants from wastewater samples in dynamic headspace sampling.

  16. Dissipative particle dynamics simulations of the viscosities of molten TNT and molten TNT suspensions containing nanoparticles.

    Science.gov (United States)

    Zhou, Yang; Li, Yixue; Qian, Wen; He, Bi

    2016-09-01

    Based on dissipative particle dynamics (DPD) methods and experimental data, we used an empirical relationship between the DPD temperature and the real temperature to build a model that describes the viscosity of molten TNT fluids. The errors in the predicted viscosity based on this model were no more than 2.3 %. We also studied the steady-state shear rheological behavior of molten TNT fluids containing nanoparticles ("nanofluids"). The dependence of the nanofluid viscosity on the temperature was found to satisfy an Arrhenius-type equation, η = Ae (B/T) , where B, the flow activation energy, depends on particle content, size, and shape. We modified the Einstein-type viscosity model to account for the effects of nanoparticle solvation in TNT nanofluids. The resulting model was able to correctly predict the viscosities of suspensions containing nano- to microsized particles, and did not require any changes to the physical background of Einstein's viscosity theory. Graphical Abstract The revised Einstein viscosity model that correctly predict the viscosity of TNT suspensions containing nanoparticles.

  17. Morphology of melt-rich channels formed during reaction infiltration experiments on partially molten mantle rocks

    Science.gov (United States)

    Pec, Matej; Holtzman, Benjamin; Zimmerman, Mark; Kohlstedt, David

    2016-04-01

    Geochemical, geophysical and geological observations suggest that melt extraction from the partially molten mantle occurs by some sort of channelized flow. Melt-solid reactions can lead to melt channelization due to a positive feedback between melt flow and reaction. If a melt-solid reaction increases local permeability, subsequent flow is increased as well and promotes further reaction. This process can lead to the development of high-permeability channels which emerge from background flow. In nature, anastomozing tabular dunite bodies within peridotitic massifs are thought to represent fossilized channels that formed by reactive flow. The conditions under which such channels can emerge are treated by the reaction infiltration instability (RII) theory (e.g. Szymczak and Ladd 2014). In this contribution, we report the results of a series of Darcy type experiments designed to study the development of channels due to RII in mantle lithologies (Pec et al. 2015). We sandwiched a partially molten rock between a melt source and a porous sink and annealed it at high-pressures (P = 300 MPa) and high-temperatures (T = 1200° or 1250° C) under a controlled pressure gradient (∇P = 0-100 MPa/mm) for up to 5 hours. The partially molten rock is formed by 50:50 mixtures of San Carlos olivine (Ol, Fo ˜ 88) and clinopyroxene (Cpx) with either 4, 10 or 20 vol% of alkali basalt added. The source and sink are disks of alkali basalt and porous alumina, respectively. During the experiments, silica undersaturated melt from the melt source dissolves Cpx and precipitates an iron rich Ol (Fo ˜ 82) thereby forming a Cpx-free reaction layer at the melt source - partially molten rock interface. The melt fraction in the reaction layer increases significantly (40% melt) compared to the protolith, confirming that the reaction increases the permeability of the partially molten rock. In experiments annealed under a low pressure gradient (and hence slow melt flow velocity) the reaction layer is

  18. Supported Molten Metal Catalysis. A New Class of Catalysts

    Energy Technology Data Exchange (ETDEWEB)

    Ravindra Datta; Ajeet Singh; Manuela Serban; Istvan Halasz

    2006-06-02

    We describe a new class of heterogeneous catalysts called supported molten metal catalysis (SMMC), in which molten metal catalysts are dispersed as nanodroplets on the surface of porous supports, allowing much larger active surface area than is possible in conventional contacting techniques for catalytic metals that are molten under reaction conditions, thus greatly enhancing their activity and potential utility. Specific examples of different types of reactions are provided to demonstrate the broad applicability of the technique in designing active, selective, and stable new catalysts. It is shown that dispersing the molten metal on a support in the suggested manner can enhance the rate of a reaction by three to four orders of magnitude as a result of the concomitant increase in the active surface area. New reaction examples include {gamma}-Al{sub 2}O{sub 3} supported molten Te (melting point 450 C) and Ga (MP 30 C) catalysts for bifunctional methylcyclohexane dehydrogenation. These catalysts provide activity similar to conventional Pt-based catalysts for this with better resistance to coking. In addition, results are described for a controlled pore glass supported molten In (MP 157 C) catalyst for the selective catalytic reduction of NO with ethanol in the presence of water, demonstrating activities superior to conventional catalysts for this reaction. A discussion is also provided on the characterization of the active surface area and dispersion of these novel supported catalysts. It is clear based on the results described that the development of new active and selective supported molten metal catalysts for practical applications is entirely plausible.

  19. Feeding tube insertion - gastrostomy

    Science.gov (United States)

    ... this page: //medlineplus.gov/ency/article/002937.htm Feeding tube insertion - gastrostomy To use the sharing features on this page, please enable JavaScript. A gastrostomy feeding tube insertion is the placement of a feeding ...

  20. Neural Tube Defects

    Science.gov (United States)

    Neural tube defects are birth defects of the brain, spine, or spinal cord. They happen in the ... that she is pregnant. The two most common neural tube defects are spina bifida and anencephaly. In ...

  1. LIFE Materails: Molten-Salt Fuels Volume 8

    Energy Technology Data Exchange (ETDEWEB)

    Moir, R; Brown, N; Caro, A; Farmer, J; Halsey, W; Kaufman, L; Kramer, K; Latkowski, J; Powers, J; Shaw, H; Turchi, P

    2008-12-11

    The goals of the Laser Inertial Fusion Fission Energy (LIFE) is to use fusion neutrons to fission materials with no enrichment and minimum processing and have greatly reduced wastes that are not of interest to making weapons. Fusion yields expected to be achieved in NIF a few times per day are called for with a high reliable shot rate of about 15 per second. We have found that the version of LIFE using TRISO fuel discussed in other volumes of this series can be modified by replacing the molten-flibe-cooled TRISO fuel zone with a molten salt in which the same actinides present in the TRISO particles are dissolved in the molten salt. Molten salts have the advantage that they are not subject to radiation damage, and hence overcome the radiation damage effects that may limit the lifetime of solid fuels such as TRISO-containing pebbles. This molten salt is pumped through the LIFE blanket, out to a heat exchanger and back into the blanket. To mitigate corrosion, steel structures in contact with the molten salt would be plated with tungsten or nickel. The salt will be processed during operation to remove certain fission products (volatile and noble and semi-noble fission products), impurities and corrosion products. In this way neutron absorbers (fission products) are removed and neutronics performance of the molten salt is somewhat better than that of the TRISO fuel case owing to the reduced parasitic absorption. In addition, the production of Pu and rare-earth elements (REE) causes these elements to build up in the salt, and leads to a requirement for a process to remove the REE during operation to insure that the solubility of a mixed (Pu,REE)F3 solid solution is not exceeded anywhere in the molten salt system. Removal of the REE will further enhance the neutronics performance. With molten salt fuels, the plant would need to be safeguarded because materials of interest for weapons are produced and could potentially be removed.

  2. Gasification characteristics of organic waste by molten salt

    Science.gov (United States)

    Sugiura, Kimihiko; Minami, Keishi; Yamauchi, Makoto; Morimitsu, Shinsuke; Tanimoto, Kazumi

    Recently, along with the growth in economic development, there has been a dramatic accompanying increase in the amount of sludge and organic waste. The disposal of such is a significant problem. Moreover, there is also an increased in the consumption of electricity along with economic growth. Although new energy development, such as fuel cells, has been promoted to solve the problem of power consumption, there has been little corresponding promotion relating to the disposal of sludge and organic waste. Generally, methane fermentation comprises the primary organic waste fuel used in gasification systems. However, the methane fermentation method takes a long time to obtain the fuel gas, and the quality of the obtained gas is unstable. On the other hand, gasification by molten salt is undesirable because the molten salt in the gasification gas corrodes the piping and turbine blades. Therefore, a gasification system is proposed by which the sludge and organic waste are gasified by molten salt. Moreover, molten carbonate fuel cells (MCFC) are needed to refill the MCFC electrolyte volatilized in the operation. Since the gasification gas is used as an MCFC fuel, MCFC electrolyte can be provided with the fuel gas. This paper elucidates the fundamental characteristics of sludge and organic waste gasification. A crucible filled with the molten salt comprising 62 Li 2CO 3/38 K 2CO 3, is installed in the reaction vessel, and can be set to an arbitrary temperature in a gas atmosphere. In this instance, the gasifying agent gas is CO 2. Sludge or the rice is supplied as organic waste into the molten salt, and is gasified. The chemical composition of the gasification gas is analyzed by a CO/CO 2 meter, a HC meter, and a SO x meter gas chromatography. As a result, although sludge can generate CO and H 2 near the chemical equilibrium value, all of the sulfur in the sludge is not fixed in the molten salt, because the sludge floats on the surface of the carbonate by the specific

  3. Overview on CO2 valorisation: challenge of molten carbonates

    Directory of Open Access Journals (Sweden)

    Déborah eChery

    2015-10-01

    Full Text Available The capture and utilisation of CO2 is becoming progressively one of the significant challenges in the field of energetic resources. Whatever the energetic device, it is impossible to avoid completely the production of greenhouse gas, even parting from renewable energies. Transforming CO2 in a valuable fuel, such as alcohols, CO or even C, could constitute a conceptual revolution in the energetic bouquet offering a huge application domain. Although several routes have been tested for this purpose, on which a general panorama will be given here, molten carbonates are attracting a renewed interest aiming at dissolving and reducing carbon dioxide in such melts. Because of their unique properties, molten carbonates are already used as electrolytes in molten carbonate fuel cells; they can also provoke a breakthrough in a new economy considering CO2 as an energetic source rather than a waste. Molten carbonates science and technology is becoming a strategic field of research for energy and environmental issues. Our aim in this review is to put in evidence the benefits of molten carbonates to valorise CO2 and to show that it is one of the most interesting routes for such application.

  4. Viscosity of molten lithium, thorium and beryllium fluorides mixtures

    Science.gov (United States)

    Merzlyakov, Alexander V.; Ignatiev, Victor V.; Abalin, Sergei S.

    2011-12-01

    Considering development of Molten Salt Fast Reactor (MSFR) concept, following Molten Salt fluorides mixtures have been chosen as an object for viscosity studies in this work (in mol%): 78LiF-22ThF 4; 71LiF-27ThF 4-2BeF 2 and 75LiF-20ThF 4-5BeF 2. Additionally, the effect of the 3 mol% CeF 3 additives on viscosity of the molten 75LiF-20ThF 4-5BeF 2 (mol%) salt mixture has been investigated experimentally. The method of torsional oscillations of cylindrical crucible filled by molten fluorides mixture has been chosen for kinematic viscosity measurement at temperatures up to 800-850 °C. In temperature ranges, where melts behave as normal liquids, dependences on viscosity vs. temperature are received: ν = А exp [B/T(K)], where ν - kinematic viscosity, m 2/s; T - temperature, K. The kinematic viscosity Rout mean squares (RMS) estimated in the assumption about dispersion homoscedasticity is (0.04-0.12) × 10 -6 (m 2/s). Discrepancies left in the data of viscosity for molten mixtures of LiF, BeF 2 and ThF 4 received by different researchers need further investigations in this area to be continued.

  5. Presence of Li Clusters in Molten LiCl-Li

    Science.gov (United States)

    Merwin, Augustus; Phillips, William C.; Williamson, Mark A.; Willit, James L.; Motsegood, Perry N.; Chidambaram, Dev

    2016-05-01

    Molten mixtures of lithium chloride and metallic lithium are of significant interest in various metal oxide reduction processes. These solutions have been reported to exhibit seemingly anomalous physical characteristics that lack a comprehensive explanation. In the current work, the physical chemistry of molten solutions of lithium chloride and metallic lithium, with and without lithium oxide, was investigated using in situ Raman spectroscopy. The Raman spectra obtained from these solutions were in agreement with the previously reported spectrum of the lithium cluster, Li8. This observation is indicative of a nanofluid type colloidal suspension of Li8 in a molten salt matrix. It is suggested that the formation and suspension of lithium clusters in lithium chloride is the cause of various phenomena exhibited by these solutions that were previously unexplainable.

  6. Features of molten pool free surface in laser processing

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    On the basis of static characteristics of free surface of molten pools in laser processing, starting with the change of surface tension, the uniform numerical models are developed for both the liquid and solid regions of metals by applying the enthalpy source method and the porous region model. The flow and heat transfer characteristics in the molten pools and the distribution of surface tension on free surface are disclosed. The shape of free surface is analyzed by considering the static forces on the free surface and by combining with the calculated results of the molten pool. The model is applied to analyzing the laser processing of AISI 304 stainless steel, and the effects of different processing tech nics and material properties on shaping of free surface are discussed.

  7. Plasma-sprayed ceramic coatings for molten metal environments.

    Energy Technology Data Exchange (ETDEWEB)

    Hollis, K. J. (Kendall J.); Peters, M. I. (Maria I.); Bartram, B. D. (Brian D.)

    2002-01-01

    Coating porosity is an important parameter to optimize for plasma-sprayed ceramics which are intended for service in molten metal environments. Too much porosity and the coatings may be infiltrated by the molten metal causing corrosive attack of the substrate or destruction of the coating upon solidification of the metal. Too little porosity and the coating may fail due to its inability to absorb thermal strains. This study describes the testing and analysis of tungsten rods coated with aluminum oxide, yttria-stabilized zirconia, yttrium oxide, and erbium oxide deposited by atmospheric plasma spraying. The samples were immersed in molten aluminum and analyzed after immersion. One of the ceramic materials used, yttrium oxide, was heat treated at 1000 C and 2000 C and analyzed by X-ray diffractography and mercury intrusion porosimetry. Slight changes in crysl nl structure and significant changes in porosity were observed after heat treatments.

  8. Molten salt reactor: Deterministic safety evaluation

    Energy Technology Data Exchange (ETDEWEB)

    Merle-Lucotte, Elsa; Heuer, Daniel; Mathieu, Ludovic; Le Brun, Christian [Laboratory for Subatomic Physics and Cosmology (LPSC), 53, Avenue des Marthyrs, F-38026 Grenoble (France)

    2006-07-01

    Molten Salt Reactors (MSRs) are one of the systems retained by Generation IV as a candidate for the next generation of nuclear reactors. This type of reactor is particularly well adapted to the thorium fuel cycle (Th- {sup 233}U) which has the advantage of producing less minor actinides than the uranium-plutonium fuel cycle ({sup 238}U- {sup 239}Pu). In the frame of a major re-evaluation of the MSR concept and concentrating on some major constraints such as feasibility, breeding capability and, above all, safety, we have considered a particular reactor configuration that we call the 'unique channel' configuration in which there is no moderator in the core, leading to a quasi fast neutron spectrum. This reactor is presented in the first section. MSRs benefit from several specific advantages which are listed in a second part of this work. Beyond these advantages of the MSR, the level of the deterministic safety in such a reactor has to be assessed precisely. In a third section, we first draw up a list of the reactivity margins in our reactor configuration. We then define and quantify the parameters characterizing the deterministic safety of any reactor: the fraction of delayed neutrons, and the system's feedback coefficients that are here negative. Finally, using a simple point-kinetic evaluation, we analyze how these safety parameters impact the system when the total reactivity margins are introduced in the MSR. The results of this last study are discussed, emphasizing the satisfactory behavior of the MSR and the excellent level of deterministic safety which can be achieved. This work is based on the coupling of a neutron transport code called MCNP with a materials evolution code. The former calculates the neutron flux and the reaction rates in all the cells while the latter solves the Bateman equations for the evolution of the materials composition within the cells. These calculations take into account the input parameters (power released

  9. Renewing Liquid Fueled Molten Salt Reactor Research and Development

    Science.gov (United States)

    Towell, Rusty; NEXT Lab Team

    2016-09-01

    Globally there is a desperate need for affordable, safe, and clean energy on demand. More than anything else, this would raise the living conditions of those in poverty around the world. An advanced reactor that utilizes liquid fuel and molten salts is capable of meeting these needs. Although, this technology was demonstrated in the Molten Salt Reactor Experiment (MSRE) at ORNL in the 60's, little progress has been made since the program was cancelled over 40 years ago. A new research effort has been initiated to advance the technical readiness level of key reactor components. This presentation will explain the motivation and initial steps for this new research initiative.

  10. Fabrication of catalytic electrodes for molten carbonate fuel cells

    Science.gov (United States)

    Smith, James L.

    1988-01-01

    A porous layer of catalyst material suitable for use as an electrode in a molten carbonate fuel cell includes elongated pores substantially extending across the layer thickness. The catalyst layer is prepared by depositing particulate catalyst material into polymeric flocking on a substrate surface by a procedure such as tape casting. The loaded substrate is heated in a series of steps with rising temperatures to set the tape, thermally decompose the substrate with flocking and sinter bond the catalyst particles into a porous catalytic layer with elongated pores across its thickness. Employed as an electrode, the elongated pores provide distribution of reactant gas into contact with catalyst particles wetted by molten electrolyte.

  11. Molten pool and temperature field in CO2 laser welding

    Institute of Scientific and Technical Information of China (English)

    Duan Aiqin; Chen Li; Wang Yajun; Hu Lunji

    2006-01-01

    Two measuring methods, high-speed camera and optical monitoring system, were used to study processes of laser welding. Molten pool, cooling time and temperature field were analyzed based on real measured images and optical signal data. The results show that the width of molten pool is almost equal to the width of weld, and length is about 7.8 mm. The solidification time is about 0. 5 s and the temperature gradient is great, so HAZ is very small. The method and results will be of benefit to build the relationship between welding parameters and microstructure.

  12. Surface Tension of Molten Ni and Ni-Co Alloys

    Institute of Scientific and Technical Information of China (English)

    Feng XIAO; Liang FANG; Kiyoshi NOGI

    2005-01-01

    Surface tension of molten Ni and Ni-Co (5 and 10 mass fraction) alloys was measured at the temperature range of 1773~1873 K using an improved sessile drop method with an alumina substrate in an Ar+3%H2 atmosphere. The error of the data obtained was analyzed. The surface tension of molten Ni and Ni-Co (5 and 10 mass fraction) alloys decreases with increasing temperature. The influence of Co on the surface tension of Ni-Co alloys is little in the studied Co concentration range.

  13. Electrochemical studies on cerium(Ⅲ) in molten fluoride mixtures

    Institute of Scientific and Technical Information of China (English)

    VIRGIL; CONSTANTIN; ANA-MARIA; POPESCU; MIRCEA; OLTEANU

    2010-01-01

    This study aims to determine the principal electrochemical characteristics of the electrodeposition of cerium metal from molten fluoride systems.The cathodic process of Ce3+ ions in LiF-NaF and LiF-NaF-CaF2 molten salts was studied using electrochemical techniques as steady state and cyclic voltammetry methods.The decomposition potential(Ed) and the overvoltage(η) were determined for NaCeF4 using current-potential curves under galvanostatic conditions.The Ed was found to be 2.025 V in LiF-NaF and 2.045 V in...

  14. Stabilization of STEP electrolyses in lithium-free molten carbonates

    CERN Document Server

    Licht, Stuart

    2012-01-01

    This communication reports on effective electrolyses in lithium-free molten carbonates. Processes that utilize solar thermal energy to drive efficient electrolyses are termed Solar Thermal Electrochemical Processes (STEP). Lithium-free molten carbonates, such as a sodium-potassium carbonate eutectic using an iridium anode, or a calcium-sodium-potassium carbonate eutectic using a nickel anode, can provide an effective medium for STEP electrolyses. Such electrolyses are useful in STEP carbon capture, and the production of staples including STEP fuel, iron, and cement.

  15. Fast Thorium Molten Salt Reactors started with Plutonium

    OpenAIRE

    Merle-Lucotte, E.; Heuer, D.; Le Brun, C.; Mathieu, L.; Brissot, R.; Liatard, E.; Méplan, O.; Nuttin, A.

    2006-01-01

    One of the pending questions concerning Molten Salt Reactors based on the 232Th/233U fuel cycle is the supply of the fissile matter, and as a consequence the deployment possibilities of a fleet of Molten Salt Reactors, since 233U does not exist on earth and is not yet produced in the current operating reactors. A solution may consist in producing 233U in special devices containing Thorium, in Pressurized Water or Fast Neutrons Reactors. Two alternatives to produce 233U are examined here: dire...

  16. Castable Cement Can Prevent Molten-Salt Corrosion in CSP

    Energy Technology Data Exchange (ETDEWEB)

    2016-09-01

    NREL's study demonstrated that castable cements on metals are a protective barrier that can prevent permeation of molten salts toward metallic surfaces. The silica-based castable cement Aremco 645-N, when sprayed with boron nitride, can protect containment metallic alloys from attack by molten chlorides at high temperatures (650 degrees C) in short-term tests. Improved thermal energy storage technology could increase the performance of CSP and reduce costs, helping to reach the goal of the U.S. Department of Energy's SunShot Initiative to make solar cost-competitive with other non-renewable sources of electricity by 2020.

  17. Nuclear Hybrid energy Systems: Molten Salt Energy Storage

    Energy Technology Data Exchange (ETDEWEB)

    Green, M.; Sabharwall, P.; Yoon, S. J.; Bragg-Sitton, S. B.; Stoot, C.

    2014-07-01

    Without growing concerns in reliable energy supply, the next generation in reliable power generation via hybrid energy systems is being developed. A hybrid energy system incorporates multiple energy input source sand multiple energy outputs. The vitality and efficiency of these combined systems resides in the energy storage application. Energy storage is necessary for grid stabilization because stored excess energy is used later to meet peak energy demands. With high thermal energy production the primary nuclear heat generation source, molten salt energy storage is an intriguing option because of its distinct thermal properties. This paper discusses the criteria for efficient energy storage and molten salt energy storage system options for hybrid systems. (Author)

  18. SENER molten salt tower technology. Ouarzazate NOOR III case

    Science.gov (United States)

    Relloso, Sergio; Gutiérrez, Yolanda

    2017-06-01

    NOOR III 150 MWe project is the evolution of Gemasolar (19.9 MWe) to large scale Molten Salt Tower plants. With more than 5 years of operational experience, Gemasolar lessons learned have been the starting point for the optimization of this technology, considered the leader of potential cost reduction in CSP. In addition, prototypes of plant key components (heliostat and receiver) were manufactured and thoroughly tested before project launch in order to prove the new engineering solutions adopted. The SENER proprietary technology of NOOR III will be applied in the next Molten Salt Tower plants that will follow in other countries, such as South Africa, Chile and Australia.

  19. Molten Triazolium Chloride Systems as New Aluminum Battery Electrolytes

    DEFF Research Database (Denmark)

    Vestergaard, B.; Bjerrum, Niels; Petrushina, Irina

    1993-01-01

    The possibility of using molten mixtures of 1,4-dimethyl-1,2,4-triazolium chloride (DMTC) and aluminum chloride (AlCl3) as secondary battery electrolytes was studied, in some cases extended by the copresence of sodium chloride. DMTC-AlCl, mixtures demonstrated high specific conductivity in a wide...... of milliamperes per square centimeter) was observed at 0.344 V on the acidic sodium tetrachloroaluminate background, involving a free triazolium radical mechanism. Molten DMTC-AlCl3 electrolytes are acceptable for battery performance and both the aluminum anode and the triazolium electrolyte can be used as active...

  20. Effect of Rotational Speeds on the Cast Tube During Vertical Centrifugal Casting Process on Appearance, Microstructure, and Hardness Behavior for Al-2Si Alloy

    Science.gov (United States)

    Shailesh Rao, A.; Tattimani, Mahantesh S.; Rao, Shrikantha S.

    2015-04-01

    The flow of molten metal plays a crucial role in determining casting quality. During rotation of the mold, melt flow around its inner circumference determines the final configurations and properties of the cast tube. In this paper, Al-2Si alloy is cast in the vertical mold at the various rotational speeds of the mold. The uniform cylinder tube is formed at a rotational speed of 1000 rpm, while before and beyond this speed, irregular-shaped cast tube is formed. Finally, fine structured grain size with high hardness value is found in uniform cast tube compared with others.

  1. 胃肠术后胆汁返流与鼻胃管拔除时机关系研究%Relation Research Between Bile Regurgitation and Nasal-stomach Tube Extraction Time Post Operation

    Institute of Scientific and Technical Information of China (English)

    张静; 丁雪青; 马晓华; 吴美珍; 程锦珍

    2002-01-01

    目的为减轻胃肠术后病人身心痛苦,提高护理工作效率以及正确掌握拔除鼻胃管的时机,探讨胃肠术后检测胃液胆汁返流对判断拔除鼻胃管时机的关系.方法选取我院普外科行胃大部切除(10例)、胃及十二指肠溃疡穿孔修补术(各5例)并顺利在术后第3天拔除鼻胃管的20例住院病人,术后每日定时检测胃液常规胆红素水平、胃液量及pH值,分析每日胃液胆汁返流与胃液量以及随时间改变的关系.结果除手术当日胃液胆汁返流与胃液量不相关外,术后3天两者均呈显著性相关;胃液pH值术后改变不显著;每日胃胆汁返流及胃液量随时间呈类似曲线变化.结论利用胃液常规检测胆红素水平能够判断胆汁返流情况,胃肠手术病人术后每日胃胆汁返流同胃液量一样随时间呈类似曲线变化,当现察到术后每日胃液胆汁返流呈曲线变化接近术前水平或为阴性时提示为鼻胃管拔除时机,该法可以单独应用指导判断拔管时机.%Objective Purpose In order to reduce patients' pain of body and metal post gastrointestinal operation, improve work efficiency of nursing and correctly master nasal-stomach extraction time,we probed the relation between determining gastric juice and bile regurgitation and nasal-stomach exepaction time post gastrointestinal operation. Methods Chose patients(10 cases) who were large part gastrectomy in general surgery department of our hospital, five patients who were stomach and duodental ulcer resection of perforation , and twenty in-patients who were extracted nasal-stomach tubes on the third day after operation. Post operation the patients were determined the level of bilirubin in gastric juice,gastric volume and pH timely every day, we analyzed the relation between gastric juice and bile regurgation and gastric volume and changing with time. Results Except that gastric juice and bile regurgitation was not correlative to gastric volume

  2. Intercostal drainage tube or intracardiac drainage tube?

    Directory of Open Access Journals (Sweden)

    N Anitha

    2016-01-01

    Full Text Available Although insertion of chest drain tubes is a common medical practice, there are risks associated with this procedure, especially when inexperienced physicians perform it. Wrong insertion of the tube has been known to cause morbidity and occasional mortality. We report a case where the left ventricle was accidentally punctured leading to near-exsanguination. This report is to highlight the need for experienced physicians to supervise the procedure and train the younger physician in the safe performance of the procedure.

  3. Torsion of a cylinder of partially molten mantle with a spherical inclusion: theory and simulation

    CERN Document Server

    Alisic, Laura; Rudge, John F; Katz, Richard F; Wells, Garth N

    2015-01-01

    The processes that are involved in migration and extraction of melt from the mantle are not yet fully understood. Gaining a better understanding of material properties of partially molten rock could help shed light on the behavior of melt on larger scales in the mantle. In this study, we simulate three-dimensional torsional deformation of a partially molten rock that contains a rigid, spherical inclusion. We compare the computed porosity patterns to those found in recent laboratory experiments. The laboratory experiments show emergence of melt-rich bands throughout the rock sample, and pressure shadows around the inclusion. The numerical model displays similar melt-rich bands only for a small bulk-to-shear-viscosity ratio (five or less). The results are consistent with earlier two-dimensional numerical simulations, however we show that it is easier to form melt-rich bands in three dimensions compared to two. The addition of strain-rate dependence of the viscosity causes a distinct change in the shape of press...

  4. Simulation tools and new developments of the molten salt fast reactor

    Energy Technology Data Exchange (ETDEWEB)

    Heuer, D.; Merle-Lucotte, E.; Allibert, M.; Doligez, X.; Ghetta, V. [LPSC-IN2P3-CNRS/UJF, 38 - Grenoble (France)

    2010-11-15

    In the MSFR (Molten Salt Fast Reactor), the liquid fuel processing is part of the reactor where a small side stream of the molten salt is processed for fission product removal and then returned to the reactor. Because of this design characteristic, the MSFR can thus operate with a widely varying fuel composition. Our reactor's studies of the MSFR concept rely on numerical simulations making use of the MCNP neutron transport code coupled with a code for Bateman's equations computing the population of any nucleus inside any part of the reactor at any moment. The classical Bateman's equations have been modified by adding 2 terms representing the reprocessing capacities and an online addition. We have thus coupled neutronic and reprocessing simulation codes in a numerical tool used to calculate the extraction efficiencies of fission products, their location in the whole system and radioprotection issues. The very preliminary results show the potential of the neutronic-reprocessing coupling we have developed. We also show that these studies are limited by the uncertainties on the design and the knowledge of the chemical reprocessing processes. (A.C.)

  5. Decomposition of diverse solid inorganic matrices with molten ammonium bifluoride salt for constituent elemental analysis

    Energy Technology Data Exchange (ETDEWEB)

    O' Hara, Matthew J.; Kellogg, Cyndi M.; Parker, Cyrena M.; Morrison, Samuel S.; Corbey, Jordan F.; Grate, Jay W.

    2017-09-01

    Ammonium bifluoride (ABF, NH4F·HF) is a well-known reagent for converting metal oxides to fluorides and for its applications in breaking down minerals and ores in order to extract useful components. It has been more recently applied to the decomposition of inorganic matrices prior to elemental analysis. Herein, a sample decomposition method that employs molten ABF sample treatment in the initial step is systematically evaluated across a range of inorganic sample types: glass, quartz, zircon, soil, and pitchblende ore. Method performance is evaluated across the two variables: duration of molten ABF treatment and ABF reagent mass to sample mass ratio. The degree of solubilization of these sample classes are compared to the fluoride stoichiometry that is theoretically necessary to enact complete fluorination of the sample types. Finally, the sample decomposition method is performed on several soil and pitchblende ore standard reference materials, after which elemental constituent analysis is performed by ICP-OES and ICP-MS. Elemental recoveries are compared to the certified values; results indicate good to excellent recoveries across a range of alkaline earth, rare earth, transition metal, and actinide elements.

  6. Thermochemical investigation of molten fluoride salts for Generation IV nuclear applications - an equilibrium exercise

    NARCIS (Netherlands)

    Meer, J.P.M. van der

    2006-01-01

    The concept of the Molten Salt Reactor, one of the so-called Generation IV future reactors, is that the fuel, a fissile material, which is dissolved in a molten fluoride salt, circulates through a closed circuit. The heat of fission is transferred to a second molten salt coolant loop, the heat of wh

  7. 中频油管电加热技术在油田热采中的应用%Application of Electrically Heating Oil Tube Technology in oil extraction

    Institute of Scientific and Technical Information of China (English)

    钱振斌; 廖幸

    2011-01-01

    A kind of heating technology directly heating crude oil in the oil tube by making use of the oil tube and bushing is developed in the paper. Electric power is sent to the oil tube, which is connected with the bushing by the oil bushing connecter on the bottom of the oil tube, via a AC-DC-AC inverse circuit. The oil tube is the heat supply, so heat energy is transformed by electric power, directly heat the crude oil in the tube. The method can effectively solve the network disturbance problem of the electric power transmission-line system, and wax coagulation on the tube wall.%本文提出一种中频油管电加热技术,它利用油井中的油管做热源体,将电能转化成热能直接加热井筒内的液体.电能由三相配电变压器输出,经AC -DC- AC逆变电路输出电能传送到油管,经油管下部的油套管接触器连接到套管,形成一个完整的回路.本技术有效地解决了电网扰动和采油油管结蜡问题.

  8. Minimization of the negative influence on the biosphere in heavy oil extraction and ecologically clean technology for the injection of the steam with supercritical parameters in oil strata on the basis of new ecologically clean tubing pipes with heat-resistant coatings

    Science.gov (United States)

    Komkov, M. A.; Moiseev, V. A.; Tarasov, V. A.; Timofeev, M. P.

    2015-12-01

    Some ecological problems related to heavy-oil extraction and ways for minimizing the negative impacts of this process on the biosphere are discussed. The ecological hazard of, for example, frequently used multistage hydraulic fracturing of formation is noted and the advantages and perspectives of superheated steam injection are considered. Steam generators of a new type and ecologically clean and costeffective insulating for tubing pipes (TPs) are necessary to develop the superheated steam injection method. The article is devoted to solving one of the most important and urgent tasks, i.e., the development and usage of lightweight, nonflammable, environmentally safe, and cost-effective insulating materials. It is shown that, for tubing shielding operating at temperatures up to 420°C, the most effective thermal insulation is a highly porous material based on basalt fiber. The process of filtration deposition of short basalt fibers with a bunch of alumina thermal insulation tubing pipe coatings in the form of cylinders and cylindrical shells from liquid pulp is substantiated. Based on the thermophysical characteristics of basalt fibers and on the technological features of manufacturing highly porous coating insulation, the thickness of a tubing pipe is determined. During the prolonged pumping of the air at an operating temperature of 400°C in the model sample of tubing pipes with insulation and a protective layer, we find that the surface temperature of the thermal barrier coating does not exceed 60°C. Introducing the described technology will considerably reduce the negative impact of heavy-oil extraction on the biosphere.

  9. In situ observation and analysis of ultrasonic capillary effect in molten aluminium.

    Science.gov (United States)

    Tzanakis, I; Xu, W W; Eskin, D G; Lee, P D; Kotsovinos, N

    2015-11-01

    An in situ synchrotron radiographic study of a molten Al-10 wt% Cu alloy under the influence of an external ultrasonic field was carried out using the Diamond-Manchester Branchline pink X-ray imaging at the Diamond Light Source in UK. A bespoke test rig was used, consisting of an acoustic transducer with a titanium sonotrode coupled with a PID-controlled resistance furnace. An ultrasonic frequency of 30 kHz, with a peak to peak amplitude at 140 microns, was used, producing a pressure output of 16.9 MPa at the radiation surface of the 1-mm diameter sonotrode. This allowed quantification of not only the cavitation bubble formation and collapse, but there was also evidence of the previously hypothesised ultrasonic capillary effect (UCE), providing the first direct observations of this phenomenon in a molten metallic alloy. This was achieved by quantifying the re-filling of a pre-existing groove in the shape of a tube (which acted as a micro-capillary channel) formed by the oxide envelope of the liquid sample. Analytical solutions of the flow suggest that the filling process, which took place in very small timescales, was related to micro-jetting from the collapsing cavitation bubbles. In addition, a secondary mechanism of liquid penetration through the groove, which is related with the density distribution of the oxides inside the groove, and practically to the filtration of aluminium melt from oxides, was revealed. The observation of the almost instantaneous re-filling of a micro-capillary channel with the metallic melt supports the hypothesised sono-capillary effect in technologically important liquids other than water, like metallic alloys with substantially higher surface tension and density.

  10. Pulse Tube Refrigerator

    Science.gov (United States)

    Matsubara, Yoichi

    The pulse tube refrigerator is one of the regenerative cycle refrigerators such as Stirling cycle or Gifford-McMahon cycle which gives the cooling temperature below 150 K down to liquid helium temperature. In 1963, W. E. Gifford invented a simple refrigeration cycle which is composed of compressor, regenerator and simple tube named as pulse tube which gives a similar function of the expander in Stirling or Gifford-McMahon cycle. The thermodynamically performance of this pulse tube refrigerator is inferior to that of other regenerative cycles. In 1984, however, Mikulin and coworkers made a significant advance in pulse tube configuration called as orifice pulse tube. After this, several modifications of the pulse tube hot end configuration have been developed. With those modifications, the thermodynamic performance of the pulse tube refrigerator became the same order to that of Stirling and Gifford-McMahon refrigerator. This article reviews the brief history of the pulse tube refrigerator development in the view point of its thermodynamically efficiency. Simplified theories of the energy flow in the pulse tube have also been described.

  11. Structural change in molten basalt at deep mantle conditions.

    Science.gov (United States)

    Sanloup, Chrystèle; Drewitt, James W E; Konôpková, Zuzana; Dalladay-Simpson, Philip; Morton, Donna M; Rai, Nachiketa; van Westrenen, Wim; Morgenroth, Wolfgang

    2013-11-07

    Silicate liquids play a key part at all stages of deep Earth evolution, ranging from core and crust formation billions of years ago to present-day volcanic activity. Quantitative models of these processes require knowledge of the structural changes and compression mechanisms that take place in liquid silicates at the high pressures and temperatures in the Earth's interior. However, obtaining such knowledge has long been impeded by the challenging nature of the experiments. In recent years, structural and density information for silica glass was obtained at record pressures of up to 100 GPa (ref. 1), a major step towards obtaining data on the molten state. Here we report the structure of molten basalt up to 60 GPa by means of in situ X-ray diffraction. The coordination of silicon increases from four under ambient conditions to six at 35 GPa, similar to what has been reported in silica glass. The compressibility of the melt after the completion of the coordination change is lower than at lower pressure, implying that only a high-order equation of state can accurately describe the density evolution of silicate melts over the pressure range of the whole mantle. The transition pressure coincides with a marked change in the pressure-evolution of nickel partitioning between molten iron and molten silicates, indicating that melt compressibility controls siderophile-element partitioning.

  12. Sorbitol dehydration into isosorbide in a molten salt hydrate medium

    NARCIS (Netherlands)

    Li, J.; Spina, A.; Moulijn, J.A.; Makkee, M.

    2013-01-01

    The sorbitol conversion in a molten salt hydrate medium (ZnCl2; 70 wt% in water) was studied. Dehydration is the main reaction, initially 1,4- and 3,6-anhydrosorbitol are the main products that are subsequently converted into isosorbide; two other anhydrohexitols, (1,5- and 2,5-), formed are in less

  13. Treatment of plutonium process residues by molten salt oxidation

    Energy Technology Data Exchange (ETDEWEB)

    Stimmel, J.; Wishau, R.; Ramsey, K.B.; Montoya, A.; Brock, J. [Los Alamos National Lab., NM (United States); Heslop, M. [Naval Surface Warfare Center (United States). Indian Head Div.; Wernly, K. [Molten Salt Oxidation Corp. (United States)

    1999-04-01

    Molten Salt Oxidation (MSO) is a thermal process that can remove more than 99.999% of the organic matrix from combustible {sup 238}Pu material. Plutonium processing residues are injected into a molten salt bed with an excess of air. The salt (sodium carbonate) functions as a catalyst for the conversion of the organic material to carbon dioxide and water. Reactive species such as fluorine, chlorine, bromine, iodine, sulfur, phosphorous and arsenic in the organic waste react with the molten salt to form the corresponding neutralized salts, NaF, NaCl, NaBr, NaI, Na{sub 2}SO{sub 4}, Na{sub 3}PO{sub 4} and NaAsO{sub 2} or Na{sub 3}AsO4. Plutonium and other metals react with the molten salt and air to form metal salts or oxides. Saturated salt will be recycled and aqueous chemical separation will be used to recover the {sup 238}Pu. The Los Alamos National Laboratory system, which is currently in the conceptual design stage, will be scaled down from current systems for use inside a glovebox.

  14. Thermodynamic characterization of salt components for Molten Salt Reactor fuel

    NARCIS (Netherlands)

    Capelli, E.

    2016-01-01

    The Molten Salt Reactor (MSR) is a promising future nuclear fission reactor technology with excellent performance in terms of safety and reliability, sustainability, proliferation resistance and economics. For the design and safety assessment of this concept, it is extremely important to have a thor

  15. Research and development issues for molten carbonate fuel cells

    Energy Technology Data Exchange (ETDEWEB)

    Krumpelt, M.

    1996-04-01

    This paper describes issues pertaining to the development of molten carbonate fuel cells. In particular, the corrosion resistance and service life of nickel oxide cathodes is described. The resistivity of lithium oxide/iron oxides and improvement with doping is addressed.

  16. Oxygen electrode reaction in molten carbonate fuel cells

    Energy Technology Data Exchange (ETDEWEB)

    Appleby, A.J.; White, R.E.

    1992-07-07

    Molten carbonate fuel cell system is a leading candidate for the utility power generation because of its high efficiency for fuel to AC power conversion, capability for an internal reforming, and a very low environmental impact. However, the performance of the molten carbonate fuel cell is limited by the oxygen reduction reaction and the cell life time is limited by the stability of the cathode material. An elucidation of oxygen reduction reaction in molten alkali carbonate is essential because overpotential losses in the molten carbonate fuel cell are considerably greater at the oxygen cathode than at the fuel anode. Oxygen reduction on a fully-immersed gold electrode in a lithium carbonate melt was investigated by electrochemical impedance spectroscopy and cyclic voltammetry to determine electrode kinetic and mass transfer parameters. The dependences of electrode kinetic and mass transfer parameters on gas composition and temperature were examined to determine the reaction orders and the activation energies. The results showed that oxygen reduction in a pure lithium carbonate melt occurs via the peroxide mechanism. A mass transfer parameter, D{sub O}{sup 1/2}C{sub O}, estimated by the cyclic voltammetry concurred with that calculated by the EIS technique. The temperature dependence of the exchange current density and the product D{sub O}{sup 1/2}C{sub O} were examined and the apparent activation energies were determined to be about 122 and 175 kJ/ mol, respectively.

  17. Study on electrochemical characteristics of steel in molten sodium compounds

    Energy Technology Data Exchange (ETDEWEB)

    Aoto, Kazumi [Japan Nuclear Cycle Development Inst., Oarai, Ibaraki (Japan). Oarai Engineering Center

    2003-06-01

    Electrochemical characteristics of steel corrosion in molten sodium oxides were studied. No report exists about such electrochemical experiments in the melt because this molten salt is very corrosive and sodium easily corrodes gold used as a reference electrode by forming eutectics. In this study, proper protection using zirconia for the equipment part exposed to the corrosive atmosphere and the acceleration of scanning rate of the electric potential led to realization of the measurement of corrosion potential and polarization curves of steel in molten sodium oxides. Electrochemical characteristics measured agreed with the features of two types of corrosion derived from previous works such as the immersed corrosion test. Those are consistent with the fact that 'Molten salt type corrosion' occurs in the melt with higher oxygen potential and 'Na-Fe double oxidation type corrosion' occurs in the basic melt. The estimated corrosion rate for the corrosion based on the corrosion current density almost agrees with the prediction by each proposed equation. (author)

  18. Nickel catalysts for internal reforming in molten carbonate fuel cells

    NARCIS (Netherlands)

    Berger, R.J.; Doesburg, E.B.M.; Ommen, van J.G.; Ross, J.R.H.

    1996-01-01

    Natural gas may be used instead of hydrogen as fuel for the molten carbonate fuel cell (MCFC) by steam reforming the natural gas inside the MCFC, using a nickel catalyst (internal reforming). The severe conditions inside the MCFC, however, require that the catalyst has a very high stability. In orde

  19. Electrochemical Deposition of Uranium Metal in Molten Salt

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    <正>Based on the studies in the electrode process of uranium ions in the molten LiCl-KCl, we carried out the electrochemical deposition of uranium in two kinds of melts, LiCl-KCl-UCl3 and LiCl- KCl-UCl3-

  20. Molten-Salt-Based Growth of Group III Nitrides

    Science.gov (United States)

    Waldrip, Karen E.; Tsao, Jeffrey Y.; Kerley, Thomas M.

    2008-10-14

    A method for growing Group III nitride materials using a molten halide salt as a solvent to solubilize the Group-III ions and nitride ions that react to form the Group III nitride material. The concentration of at least one of the nitride ion or Group III cation is determined by electrochemical generation of the ions.

  1. Alloys compatibility in molten salt fluorides: Kurchatov Institute related experience

    Energy Technology Data Exchange (ETDEWEB)

    Ignatiev, Victor, E-mail: ignatiev@vver.kiae.ru; Surenkov, Alexandr

    2013-10-15

    In the last several years, there has been an increased interest in the use of high-temperature molten salt fluorides in nuclear power systems. For all molten salt reactor designs, materials selection is a very important issue. This paper summarizes results, which led to selection of materials for molten salt reactors in Russia. Operating experience with corrosion thermal convection loops has demonstrated good capability of the “nickel–molybdenum alloys + fluoride salt fueled by UF{sub 4} and PuF{sub 3} + cover gas” system up to 750 °C. A brief description is given of the container material work in progress. Tellurium corrosion of Ni-based alloys in stressed and unloaded conditions studies was also tested in different molten salt mixtures at temperatures up to 700–750 °C, also with measurement of the redox potential. HN80MTY alloy with 1% added Al is the most resistant to tellurium intergranular cracking of Ni-base alloys under study.

  2. Corrosion Behavior of Alloys in Molten Fluoride Salts

    Science.gov (United States)

    Zheng, Guiqiu

    The molten fluoride salt-cooled high-temperature nuclear reactor (FHR) has been proposed as a candidate Generation IV nuclear reactor. This reactor combines the latest nuclear technology with the use of molten fluoride salt as coolant to significantly enhance safety and efficiency. However, an important challenge in FHR development is the corrosion of structural materials in high-temperature molten fluoride salt. The structural alloys' degradation, particularly in terms of chromium depletion, and the molten salt chemistry are key factors that impact the lifetime of nuclear reactors and the development of future FHR designs. In support of materials development for the FHR, the nickel base alloy of Hastelloy N and iron-chromium base alloy 316 stainless steel are being actively considered as critical structural alloys. Enriched 27LiF-BeF2 (named as FLiBe) is a promising coolant for the FHR because of its neutronic properties and heat transfer characteristics while operating at atmospheric pressure. In this study, the corrosion behavior of Ni-5Cr and Ni-20Cr binary model alloys, and Hastelloy N and 316 stainless steel in molten FLiBe with and without graphite were investigated through various microstructural analyses. Based on the understanding of the corrosion behavior and data of above four alloys in molten FLiBe, a long-term corrosion prediction model has been developed that is applicable specifically for these four materials in FLiBe at 700ºC. The model uses Cr concentration profile C(x, t) as a function of corrosion distance in the materials and duration fundamentally derived from the Fick's diffusion laws. This model was validated with reasonable accuracy for the four alloys by fitting the calculated profiles with experimental data and can be applied to evaluate corrosion attack depth over the long-term. The critical constant of the overall diffusion coefficient (Deff) in this model can be quickly calculated from the experimental measurement of alloys' weight

  3. Fundamental study of molten pool depth measurement method using an ultrasonic phased array system

    Science.gov (United States)

    Mizota, Hirohisa; Nagashima, Yoshiaki; Obana, Takeshi

    2015-07-01

    The molten pool depth measurement method using an ultrasonic phased array system has been developed. The molten pool depth distribution is evaluated by comparing the times taken by the ultrasonic wave to propagate through a molten pool and a solid-phase and through only the solid-phase near the molten pool. Maximum molten pool depths on a flat type-304 stainless-steel plate, formed with a gas tungsten arc welding machine for different welding currents from 70 to 150 A, were derived within an error of ±0.5 mm.

  4. Molar Volume Analysis of Molten Ni-Al-Co Alloy by Measuring the Density

    Institute of Scientific and Technical Information of China (English)

    XIAO Feng; FANG Liang; FU Yuechao; YANG Lingchuan

    2004-01-01

    The density of molten Ni-Al-Co alloys was measured in the temperature range of 1714~1873K using a modified pycnometric method, and the molar volume of molten alloys was analyzed. The density of molten Ni-Al-Co alloys was found to decrease with increasing temperature and Co concentration in alloys. The molar volume of molten Ni-Al-Co alloys increases with increasing Co concentration in alloys. The molar volume of molten Ni-Al-Co alloys shows a negative deviation from the linear molar volume.

  5. Heated Tube Facility

    Data.gov (United States)

    Federal Laboratory Consortium — The Heated Tube Facility at NASA GRC investigates cooling issues by simulating conditions characteristic of rocket engine thrust chambers and high speed airbreathing...

  6. Fuel nozzle tube retention

    Energy Technology Data Exchange (ETDEWEB)

    Cihlar, David William; Melton, Patrick Benedict

    2017-02-28

    A system for retaining a fuel nozzle premix tube includes a retention plate and a premix tube which extends downstream from an outlet of a premix passage defined along an aft side of a fuel plenum body. The premix tube includes an inlet end and a spring support feature which is disposed proximate to the inlet end. The premix tube extends through the retention plate. The spring retention feature is disposed between an aft side of the fuel plenum and the retention plate. The system further includes a spring which extends between the spring retention feature and the retention plate.

  7. Synthesis of chromium and ferrochromium alloy in molten salts by the electro-reduction method

    Directory of Open Access Journals (Sweden)

    Ge X.

    2015-01-01

    Full Text Available In this work, we successfully applied the Fray-Farthing-Chen Cambridge electro-reduction process on the preparation of chromium from chromium oxide, and for the first time, the synthesis of ferrochromium alloy from chromium oxide and iron oxide mixture and the chromite ore in molten calcium chloride. The present work systematically investigated the influences of sintered temperature of the solid precursor, electrochemical potential, electrolysis temperature and time on the products by using a set of advanced characterization techniques, including XRD and SEM/EDS analyses. In particular, our results show that this process is energy-friendly and technically-feasible for the direct extraction of ferrochromium alloy from chromite ore. Our findings thus provide useful insights for designing a novel green process to produce ferrochromium alloy from low-grade chromite ore or stainless steel slag.

  8. Determination and correlation of mass transfer coefficients in a stirred cell. [Molten Salt Breeder Reactor

    Energy Technology Data Exchange (ETDEWEB)

    Herranz, J.; Bloxom, S.R.; Keeler, J.B.; Roth, S.R.

    1975-12-17

    In the proposed Molten Salt Breeder Reactor flowsheet, a fraction of the rare earth fission products is removed from the fuel salt in mass transfer cells. To obtain design parameters for this extraction, the effect of cell size, blade diameter, phase volume, and agitation rate on the mass transfer for a high density ratio system (mercury/water) in nondispersing square cross section contactors was determined. Aqueous side mass transfer coefficients were measured by polarography over a wide range of operating conditions. Correlations for the experimental mass transfer coefficients as functions of the operating parameters are presented. Several techniques for measuring mercury-side mass transfer coefficients were evaluated and a new one is recommended. (auth)

  9. Numerical Modelling of Induction Heating for a Molten Salts Pyrochemical Process

    Energy Technology Data Exchange (ETDEWEB)

    Vu, Xuan-Tuyen; Feraud, Jean-Pierre; Ode, Denis [CEA Marcoule: DTEC/SGCS/LGCI Bat. 57 B17171, 30207 Bagnols/Ceze (France); Du Terrail Couvat, Yves [SIMaP, Grenoble INP, CNRS: ENSEEG, BP 75, 38402 Saint Martin d' Heres Cedex (France)

    2008-07-01

    Technological developments in the pyro-chemistry program are required to allow choices for a reprocessing experiment on 100 g of spent nuclear fuel. In this context, a special device must be designed for the solid/gas reaction phases followed by actinide extraction and stripping in molten salt. This paper discusses a modelling approach for designing an induction furnace. Using this numerical approach is a good way to improve thermal performance of the device in terms of magnetic/thermal coupling phenomena. The influence of current frequency is also studied to give another view of the possibilities of an induction furnace. Electromagnetic forces are taken into account in a computational fluid dynamics code derived from a specifically developed exchange library. Induction heating systems are an example of a typical multi-physics problem involving numerically coupled equations. (authors)

  10. Steam generator tube failures

    Energy Technology Data Exchange (ETDEWEB)

    MacDonald, P.E.; Shah, V.N.; Ward, L.W.; Ellison, P.G.

    1996-04-01

    A review and summary of the available information on steam generator tubing failures and the impact of these failures on plant safety is presented. The following topics are covered: pressurized water reactor (PWR), Canadian deuterium uranium (CANDU) reactor, and Russian water moderated, water cooled energy reactor (VVER) steam generator degradation, PWR steam generator tube ruptures, the thermal-hydraulic response of a PWR plant with a faulted steam generator, the risk significance of steam generator tube rupture accidents, tubing inspection requirements and fitness-for-service criteria in various countries, and defect detection reliability and sizing accuracy. A significant number of steam generator tubes are defective and are removed from service or repaired each year. This wide spread damage has been caused by many diverse degradation mechanisms, some of which are difficult to detect and predict. In addition, spontaneous tube ruptures have occurred at the rate of about one every 2 years over the last 20 years, and incipient tube ruptures (tube failures usually identified with leak detection monitors just before rupture) have been occurring at the rate of about one per year. These ruptures have caused complex plant transients which have not always been easy for the reactor operators to control. Our analysis shows that if more than 15 tubes rupture during a main steam line break, the system response could lead to core melting. Although spontaneous and induced steam generator tube ruptures are small contributors to the total core damage frequency calculated in probabilistic risk assessments, they are risk significant because the radionuclides are likely to bypass the reactor containment building. The frequency of steam generator tube ruptures can be significantly reduced through appropriate and timely inspections and repairs or removal from service.

  11. Hologram recording tubes

    Science.gov (United States)

    Rajchman, J. H.

    1973-01-01

    Optical memories allow extremely large numbers of bits to be stored and recalled in a matter of microseconds. Two recording tubes, similar to conventional image-converting tubes, but having a soft-glass surface on which hologram is recorded, do not degrade under repeated hologram read/write cycles.

  12. Molybdenum Tube Characterization report

    Energy Technology Data Exchange (ETDEWEB)

    Beaux II, Miles Frank [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Usov, Igor Olegovich [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2017-02-07

    Chemical vapor deposition (CVD) techniques have been utilized to produce free-standing molybdenum tubes with the end goal of nuclear fuel clad applications. In order to produce tubes with properties desirable for this application, deposition rates were lowered requiring long deposition durations on the order of 50 hours. Standard CVD methods as well as fluidized-bed CVD (FBCVD) methods were applied towards these objectives. Characterization of the tubes produced in this manner revealed material suitable for fuel clad applications, but lacking necessary uniformity across the length of the tubes. The production of freestanding Mo tubes that possess the desired properties across their entire length represents an engineering challenge that can be overcome in a next iteration of the deposition system.

  13. Categorising YouTube

    DEFF Research Database (Denmark)

    Simonsen, Thomas Mosebo

    2011-01-01

    This article provides a genre analytical approach to creating a typology of the User Generated Content (UGC) of YouTube. The article investigates the construction of navigation processes on the YouTube website. It suggests a pragmatic genre approach that is expanded through a focus on YouTube’s...... technological affordances. Through an analysis of the different pragmatic contexts of YouTube, it is argued that a taxonomic understanding of YouTube must be analysed in regards to the vacillation of a user-driven bottom-up folksonomy and a hierarchical browsing system that emphasises a culture of competition...... and which favours the already popular content of YouTube. With this taxonomic approach, the UGC videos are registered and analysed in terms of empirically based observations. The article identifies various UGC categories and their principal characteristics. Furthermore, general tendencies of the UGC within...

  14. Wavy tube heat pumping

    Energy Technology Data Exchange (ETDEWEB)

    Haldeman, C. W.

    1985-12-03

    A PVC conduit about 4'' in diameter and a little more than 40 feet long is adapted for being seated in a hole in the earth and surrounds a coaxial copper tube along its length that carries Freon between a heat pump and a distributor at the bottom. A number of wavy conducting tubes located between the central conducting tube and the wall of the conduit interconnect the distributor with a Freon distributor at the top arranged for connection to the heat pump. The wavy conducting tubing is made by passing straight soft copper tubing between a pair of like opposed meshing gears each having four convex points in space quadrature separated by four convex recesses with the radius of curvature of each point slightly less than that of each concave recess.

  15. A preliminary thermal budget for lava tubes on the Earth and planets

    Science.gov (United States)

    Keszthelyi, Laszlo

    1995-10-01

    Lava tubes are a very common and important feature in mafic lava flows. The insulation provided by lava tubes allows molten lava to travel large distances from the vent with little cooling. This paper presentes the first attempt to quantify the processes that control this cooling. The resulting thermal budget balances heat loss by (1) conduction, (2) convection of air in the wall rocks, (3) vaporization of rainwater, and (4) radiation out of skylights against (1) viscous dissipation, (2) latent heat released during crystallization, and (3) the cooling of the lava. When applied to the Waha'ula tube on Kilauea Volcano, Hawaii, this thermal budget reproduces the observed ~1°C/km cooling of the lava inside the active tube. The thermal budget is also used to compare the insulating ability of hypothetical lava tubes in a continental flood basalt setting, on the ocean floor, Venus, the Moon, and Mars. This analysis demonstrates the large effect of rainfall and atmospheric convection, the importance of the volumetric flux of lava through the tube, and the overwhelming importance of compositional (i.e., rheological) differences. This work suggests that basaltic tube-fed flows several hundred kilometers long can be produced by eruptions with effusion rates of only a few tens of cubic meters per second. Thus even the longest lava flows observed in our solar system could have been produced by low to moderate effusion rate eruptions, if they were tube-fed. .

  16. Overview of the DOE studies of recovery boiler floor tube cracking

    Energy Technology Data Exchange (ETDEWEB)

    Keiser, J.R.; Taljat, B.; Wang, X.L. [and others

    1998-03-01

    Cracking of the stainless steel layer of coextruded 304L/SA210 recovery boiler floor tubes has been observed in an increasing number of black liquor recovery boilers. Because failure of such tubes is a serious safety concern as well as an economic issue, this project was initiated with the objective of identifying alternate materials or process changes that would prevent tube cracking. Tensile stresses are essential for the most likely failure mechanisms, i.e., fatigue or stress corrosion cracking, therefore stresses were measured at room temperature and modeling was used to predict stresses under operating conditions. Laboratory studies have identified conditions under which composite tubes crack due to thermal fatigue and stress corrosion. Floor tube temperature measurements have defined the magnitude and frequency of temperature fluctuations experienced by such tubes, and smelt corrosion studies have measured the degradation rate when molten smelt comes in contact with tubes. Based on these observations, certain materials appear more likely to resist cracking and certain process changes should help avoid conditions that cause composite tube cracking.

  17. Evidence for melt partitioning between olivine and orthopyroxene in partially molten harzburgite

    Science.gov (United States)

    Miller, K.; Zhu, W.; Montesi, L. G.; Le Roux, V.; Gaetani, G. A.

    2013-12-01

    During melting at mid-ocean ridges, melt is driven into an equilibrium, minimum-energy configuration by surface energy gradients between solid-solid and solid-liquid phase boundaries. Such a configuration, where melt is mostly restricted to three and four-grain junctions, acts as a porous medium through which melt can percolate to the surface. For a monomineralic system, melt is distributed evenly among all grains. However, in mineralogical heterogeneous systems, melt partitions unevenly between the various solid phases to minimize the total energy of the system. In a ocean ridge melting environment, where olivine is often juxtaposed against orthopyroxene (opx), lithologic partitioning is expected to turn olivine-rich regions into high-permeability conduits, through which melt can be quickly extracted, drastically increasing the permeability of the mantle [Zhu and Hirth, 2003]. Lithologic partitioning has been demonstrated in experiments using analogue systems [Watson, 1999]; however, to date, no experiment has confirmed its existence in partially molten mantle systems. We present experimental results that determine the degree of melt partitioning between olivine and opx in partially molten harzburgites. Samples were prepared from a powdered mixture of oxides and carbonates and then hot-pressed in a solid-media piston-cylinder apparatus at 1350°C and 1.5GPa [Zhu et al., 2011] to achieve an 82/18 vol. % ratio of olivine to opx. Prior to hot-pressing, basalt was added to the powdered mixtures in various proportions to test for lithologic partitioning across a range of melt fractions. Three-dimensional, 700nm-resolution images of our samples were obtained using synchrotron X-ray microtomography on the 2BM station of the Advanced Photon Source at Argonne National Labs. Image data were filtered using an anisotropic diffusion filter to enhance phase contrast and then segmented to produce binary representations of each phase. In order to quantitatively demonstrate

  18. Numerical modelling of steel tubes under oblique crushing forces

    Science.gov (United States)

    Ismail, A. E.; Rahman, M. Q. Abdul; Nezere, N.; Jamian, S.; Kamarudin, K. A.; Awang, M. K.; Nor, M. K. Mohd; Ibrahim, M. N.; Rasidi Ibrahim, M.; Zulafif Rahim, M.; Fahrul Hassan, Mohd; Nor, Nik Hisyamudin Muhd; Arifin, A. M. T.; Zaini Yunos, Muhamad

    2017-08-01

    This paper presents the numerical assessment of crushing responses of elliptical tubes under crushing forces. Based on the literature survey, tremendous amount of works on the axial crushing behaviour can be found. However, the studies on the oblique crushing responses are rarely found. Therefore, this work investigates numerically the elliptical tubes under compressions. The numerical model of the tubes are developed using ANSYS finite element program. Two important parameters are used such as elliptical ratios and oblique angles. The tubes are compressed quasi-statically and the force-displacement curves are extracted. Then, the area under the curves are calculated and it is represented the performances of energy absorptions. It is found numerically that the introductions of oblique angles during the crushing processes decrease the crushing performances. However, the elliptical-shaped tubes capable to enhance the energy absorption capabilities. On the other hand, the elliptical-shaped tubes produced the enhancement on the energy absorption capabilities.

  19. What Are Neural Tube Defects?

    Science.gov (United States)

    ... NICHD Research Information Clinical Trials Resources and Publications Neural Tube Defects (NTDs): Condition Information Skip sharing on social media links Share this: Page Content What are neural tube defects? Neural (pronounced NOOR-uhl ) tube defects are ...

  20. Molten Salts for High Temperature Reactors: University of Wisconsin Molten Salt Corrosion and Flow Loop Experiments -- Issues Identified and Path Forward

    Energy Technology Data Exchange (ETDEWEB)

    Piyush Sabharwall; Matt Ebner; Manohar Sohal; Phil Sharpe; Thermal Hydraulics Group

    2010-03-01

    Considerable amount of work is going on regarding the development of high temperature liquid salts technology to meet future process needs of Next Generation Nuclear Plant. This report identifies the important characteristics and concerns of high temperature molten salts (with lesson learned at University of Wisconsin-Madison, Molten Salt Program) and provides some possible recommendation for future work

  1. Electrodeposition of alloys or compounds in molten salts and applications

    Directory of Open Access Journals (Sweden)

    Taxil P.

    2003-01-01

    Full Text Available This article deals with the different modes of preparation of alloys or intermetallic compounds using the electrodeposition in molten salts, more particularly molten alkali fluorides. The interest in this process is to obtain new materials for high technology, particularly the compounds of reactive components such as actinides, rare earth and refractory metals. Two ways of preparation are considered: (i electrocoating of the more reactive metal on a cathode made of the noble one and reaction between the two metals in contact, and (ii electrocoating on an inert cathode of the intermetallic compound by coreduction of the ions of each elements. The kinetic is controlled by the reaction at the electrolyte interface. A wide bibliographic survey on the preparation of various compounds (intermetallic compounds, borides, carbides… is given and a special attention is paid to the own experience of the authors in the preparation of these compounds and interpretation of their results.

  2. Deoxidation Behavior of Alloys Bearing Barium in Molten Steel

    Institute of Scientific and Technical Information of China (English)

    LI Yang; JIANG Zhou-hua; JIANG Mao-fa; WANG Jun-wen; GU Wen-bing

    2003-01-01

    The deoxidation behaviors of alloys bearing barium in pipe steel were researched with MgO crucible under argon atmosphere in MoSi2 furnace at 1 873 K. The total oxygen contents of molten steel, the distribution, size and morphology of deoxidation products in the steel were surveyed. The metamorphic mechanism for deoxidation products of alloy bearing barium was also discussed. The results show that applying alloy bearing barium to the pipe steel, very low total oxygen contents can be obtained, and deoxidation products, which easily float up from molten steel, can be changed into globular shape and uniformly distributed in steel. The equilibrium time of total oxygen is about 25 min, and the terminal total oxygen contents range from 0.002 0 % to 0.002 2 % after treating with SiCa wire. The best deoxidizers are SiAlBaCa and SiAlBaCaSr.

  3. MAG-GATE System for Molten metal Flow Control

    Energy Technology Data Exchange (ETDEWEB)

    Richard D. Nathenson, P.E.

    2004-05-15

    The need for improved active flow control has been recognized as part of the Steel Industry Technology Roadmap. Under TRP 9808 for the American Iron and Steel Institute and the Department of Energy, Concept Engineering Group Inc. has developed MAG-GATE{trademark}, an electromagnetic system for active molten metal flow control. Two hot steel tests were successfully conducted in 2003 at the Whemco Foundry Division, Midland, PA. Approximately 110,000 pounds of 0.2% carbon steel were poured through the device subject to electromagnetic flow control. Excellent agreement between predicted and actual flow control was found. A survey of the molten metal flow control practices at 100 continuous casters in North America was also conducted in 2003. This report summarizes the results of the development program to date. Preliminary designs are described for the next step of a beta test at an operating billet/bloom or slab caster.

  4. Nuclear Hybrid Energy Systems: Molten Salt Energy Storage

    Energy Technology Data Exchange (ETDEWEB)

    P. Sabharwall; M. Green; S.J. Yoon; S.M. Bragg-Sitton; C. Stoots

    2014-07-01

    With growing concerns in the production of reliable energy sources, the next generation in reliable power generation, hybrid energy systems, are being developed to stabilize these growing energy needs. The hybrid energy system incorporates multiple inputs and multiple outputs. The vitality and efficiency of these systems resides in the energy storage application. Energy storage is necessary for grid stabilizing and storing the overproduction of energy to meet peak demands of energy at the time of need. With high thermal energy production of the primary nuclear heat generation source, molten salt energy storage is an intriguing option because of its distinct properties. This paper will discuss the different energy storage options with the criteria for efficient energy storage set forth, and will primarily focus on different molten salt energy storage system options through a thermodynamic analysis

  5. Plasma-sprayed ceramic coatings for protection against molten metal.

    Energy Technology Data Exchange (ETDEWEB)

    Hollis, K. J. (Kendall J.); Peters, M. I. (Maria I.); Bartram, B. D. (Brian D.)

    2002-01-01

    Molten metal environments pose a special demand on materials due to the high temperature corrosion effects and thermal expansion mismatch induced stress effects. A solution that has been successfully employed is the use of a base material for the mechanical strength and a coating material for the chemical compatibility with the molten metal. The work described here used such an approach coating tungsten rods with aluminum oxide, yttria-stabilized zirconia, yttrium oxide, and erbium oxide deposited by atmospheric plasma spraying. The ceramic materials were deposited under varying conditions to produce different structures. Measurement of particle characteristics was performed to correlate to material properties. The coatings were tested in a thermal cycling environment to simulate the metal melting cycle expected in service. Results of the testing indicate the effect of material composition and spray conditions on the thermal cycle crack resistance of the coatings.

  6. Molten metal analysis by laser produced plasmas. Technical progress report

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Yong W.

    1994-02-01

    A new method of molten metal analysis, based on time- and space-resolved spectroscopy of a laser-produced plasma (LPP) plume of a molten metal surface, has been implemented in the form of a prototype LPP sensor-probe, allowing in-situ analysis in less than 1 minute. The research at Lehigh University has been structured in 3 phases: laboratory verification of concept, comparison of LPP method with conventional analysis of solid specimens and field trials of prototype sensor-probe in small-scale metal shops, and design/production/installation of two sensor-probes in metal production shops. Accomplishments in the first 2 phases are reported. 6 tabs, 3 figs.

  7. Development and Application of Refractory Materials for Molten Aluminum Applications

    Energy Technology Data Exchange (ETDEWEB)

    Hemrick, James Gordon [ORNL; Headrick, William [University of Missouri, Rolla; Peters, Klaus-Markus [ORNL

    2008-01-01

    Two new refractory materials have been developed for use in molten aluminum contact applications which exhibit improved corrosion and wear resistance, along with improved thermal management through reduced heat losses. The development of these materials was based on understanding of the corrosion and wear mechanisms associated with currently used aluminum contact refractories through physical, chemical, and mechanical characterization and analysis performed by Oak Ridge National Laboratory (ORNL) and the University of Missouri, Rolla (UMR) along with their industrial partners, under the ITP Materials project "Multifunctional Metallic and Refractory Materials for Energy Efficient Handling of Molten Metals". Spent castable refractories obtained from a natural gas fired reverberatory aluminum alloy melting furnace were analyzed leading to identification of several refractory degradation mechanisms and strategies to produce improved materials. The newly developed materials have been validated through both R&D industrial trials and independent commercial trials by the refractory manufacturers.

  8. Uranium (III) precipitation in molten chloride by wet argon sparging

    Science.gov (United States)

    Vigier, Jean-François; Laplace, Annabelle; Renard, Catherine; Miguirditchian, Manuel; Abraham, Francis

    2016-06-01

    In the context of pyrochemical processes for nuclear fuel treatment, the precipitation of uranium (III) in molten salt LiCl-CaCl2 (30-70 mol%) at 705 °C is studied. First, this molten chloride is characterized with the determination of the water dissociation constant. With a value of 10-4.0, the salt has oxoacid properties. Then, the uranium (III) precipitation using wet argon sparging is studied. The salt is prepared using UCl3 precursor. At the end of the precipitation, the salt is totally free of solubilized uranium. The main part is converted into UO2 powder but some uranium is lost during the process due to the volatility of uranium chloride. The main impurity of the resulting powder is calcium. The consequences of oxidative and reductive conditions on precipitation are studied. Finally, coprecipitation of uranium (III) and neodymium (III) is studied, showing a higher sensitivity of uranium (III) than neodymium (III) to precipitation.

  9. A Reliable Reference Electrode in Molten Carbonate and Its Applications

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    A Ag|AgCl reference electrode which can be used in molten carbonate media has been described in this paper.It consists of a silver wire immersed in a solution of AgCl(1mol%) in (Li0.62,K0.38)2CO3,with a zirconia junction.The main properties of reference electrode,such as reproducibility ,stability and reversibility, were checked.The results have demonstrated that the reference electrode is reliable.With such reference electrode catalysis of various electrode materials to oxygen reduction in molten alkali carbonate media was investigated.It is found that as catalysts for oxygen reduction oxidized nickel-niobium alloy is superior to nickel oxide.

  10. Cracking of crude oil in the molten metals

    Directory of Open Access Journals (Sweden)

    Marat A. Glikin

    2014-03-01

    Full Text Available In this paper is investigated the process of crude oil and its individual fractions cracking in the molten metals medium to produce light petroleum products. Thermodynamic calculations demonstrate the possibility of using lead and tin including alloys thereof as the melt. The cracking of West Siberian crude oil is studied at temperatures 400-600 °C. It is detected that as the temperature increases there is increase of aromatic hydrocarbons and olefins content in gasoline while naphthenes, n- and i-paraffins content reduces. Optimal temperature for cracking in molten metals is ~500 °C. The use of a submerged nozzle increases the yield of light petroleum products by ~2%. The research octane number of gasoline produced is 82-87 points. It is determined that the yield of light petroleum products depending on the experimental conditions is increased from 46.9 to 55.1-61.3% wt.   

  11. High current density cathode for electrorefining in molten electrolyte

    Science.gov (United States)

    Li, Shelly X.

    2010-06-29

    A high current density cathode for electrorefining in a molten electrolyte for the continuous production and collection of loose dendritic or powdery deposits. The high current density cathode eliminates the requirement for mechanical scraping and electrochemical stripping of the deposits from the cathode in an anode/cathode module. The high current density cathode comprises a perforated electrical insulated material coating such that the current density is up to 3 A/cm.sup.2.

  12. Development of large scale internal reforming molten carbonate fuel cell

    Energy Technology Data Exchange (ETDEWEB)

    Sasaki, A.; Shinoki, T.; Matsumura, M. [Mitsubishi Electric Corp., Hyogo (Japan)

    1996-12-31

    Internal Reforming (IR) is a prominent scheme for Molten Carbonate Fuel Cell (MCFC) power generating systems in order to get high efficiency i.e. 55-60% as based on the Higher Heating Value (HHV) and compact configuration. The Advanced Internal Reforming (AIR) technology has been developed based on two types of the IR-MCFC technology i.e. Direct Internal Reforming (DIR) and Indirect Internal Reforming (DIR).

  13. Molten carbonate fuel cell reduction of nickel deposits

    Energy Technology Data Exchange (ETDEWEB)

    Smith, James L. (Lemont, IL); Zwick, Stanley A. (Darien, IL)

    1987-01-01

    A molten carbonate fuel cell with anode and cathode electrodes and an eleolyte formed with two tile sections, one of the tile sections being adjacent the anode and limiting leakage of fuel gas into the electrolyte with the second tile section being adjacent the cathode and having pores sized to permit the presence of oxygen gas in the electrolyte thereby limiting the formation of metal deposits caused by the reduction of metal compositions migrating into the electrolyte from the cathode.

  14. Temperature Modeling of the Molten Glass in Tin Bath

    Institute of Scientific and Technical Information of China (English)

    WEI Zhihua; CHEN Jinshu; NIE Yingsong

    2009-01-01

    Based on the experimental investigation by quantitative analysis, temperature fields of the molten glass in tin bath were numerically simulated by the finite elememt method. The ex-perimental results show that the cooling rate of glass is directly proportional to the draught speed, but inversely proportional to the thickness of the glass. This model lays the foundation for computer simulation system about float glass.

  15. Renewable energy and the role of molten salts and carbon

    Directory of Open Access Journals (Sweden)

    Fray D.

    2013-01-01

    Full Text Available Molten carbonate fuel cells have been under development for a number of years and reliable units are successfully working at 250kW scale and demonstration units have produced up to 2 MW. Although these cells cannot be considered as renewable as the fuel, hydrogen or carbon monoxide is consumed and not regenerated, the excellent reliability of such a cell can act as a stimulus to innovative development of similar cells with different outcomes. Molten salt electrolytes based upon LiCl - Li2O can be used to convert carbon dioxide, either drawn from the output of a conventional thermal power station or from the atmosphere, to carbon monoxide or carbon. Recently, dimensionally stable anodes have been developed for molten salt electrolytes, based upon alkali or alkaline ruthenates which are highly electronically conducting and these may allow the concept of high temperature batteries to be developed in which an alkali or alkaline earth element reacts with air to form oxides when the battery is discharging and the oxide decomposes when the battery is being recharged. Batteries using these concepts may be based upon the Hall-Heroult cell, which is used worldwide for the production of aluminium on an industrial scale, and could be used for load levelling. Lithium ion batteries are, at present, the preferred energy source for cars in 2050 as there are sufficient lithium reserves to satisfy the world’s energy needs for this particular application. Graphite is used in lithium ion batteries as the anode but the capacity is relatively low. Silicon and tin have much higher capacities and the use of these materials, encapsulated in carbon nanotubes and nanoparticles will be described. This paper will review these interesting developments and demonstrate that a combination of carbon and molten salts can offer novel ways of storing energy and converting carbon dioxide into useful products.

  16. Densities of molten Ni-(Cr, Co, W) superalloys

    Institute of Scientific and Technical Information of China (English)

    XIAO Feng; YANG Ren-hui; FANG Liang; LIU Lan-xiao; ZHAO Hong-kai

    2008-01-01

    In order to obtain more accurate density for molten Ni-(Cr, Co, W) binary alloy, the densities of molten pure Ni and Ni-Cr, Ni-Co, Ni-W alloys were measured with a sessile drop method. It is found that the measured densities of molten pure Ni and Ni-Cr, Ni-Co, Ni-W alloys decrease with increasing temperature in the experimental temperature range. The density of alloys increases with increasing W and Co concentrations while it decreases with increasing Cr concentration in the alloy at 1 773-1 873 K. The molar volume of Ni-based alloys increases with increasing W concentration while it decreases with increasing Co concentration. The effect of Cr concentration on the molar volume of the alloy is little in the studied concentration range. The accommodation among atomic species was analyzed. The deviation of molar volume from ideal mixing shows an ideal mixing of Ni-(Cr, Co, W) binary alloys.

  17. Removal of Inclusions from Molten Aluminum by Supergravity Filtration

    Science.gov (United States)

    Song, Gaoyang; Song, Bo; Yang, Zhanbing; Yang, Yuhou; Zhang, Jing

    2016-09-01

    A new approach to removing inclusions from aluminum melt by supergravity filtration was investigated. The molten aluminum containing MgAl2O4 spinel and coarse Al3Ti particles was isothermally filtered with different gravity coefficients, different filtering times, and various filtering temperatures under supergravity field. When the gravity coefficient G ≥ 50, the alloy samples were divided automatically into two parts: the upper residue and the lower filtered aluminum. All inclusions (MgAl2O4 and Al3Ti particles) were nearly intercepted in the upper residue by filter felt with average pore size of 44.78 μm. The removal efficiencies of oxide inclusions and Al3Ti particles exceeded 98 and 90 pct, respectively, at G ≥ 50, t = 2 minutes, T = 973 K (700 °C). Besides, the yield of purified aluminum was up to 92.1 pct at G = 600, t = 2 minutes, and T = 973 K (700 °C). The calculations of centrifugal pressure indicated that supergravity filtration could effectively overcome the pressure drop without meeting the rigorous requirement of height of molten metal, especially for using the fine-pore filter medium. Moreover, cake-mode filtration was the major mechanism of supergravity filtration of molten metal in this work.

  18. Removal of Inclusions from Molten Aluminum by Supergravity Filtration

    Science.gov (United States)

    Song, Gaoyang; Song, Bo; Yang, Zhanbing; Yang, Yuhou; Zhang, Jing

    2016-12-01

    A new approach to removing inclusions from aluminum melt by supergravity filtration was investigated. The molten aluminum containing MgAl2O4 spinel and coarse Al3Ti particles was isothermally filtered with different gravity coefficients, different filtering times, and various filtering temperatures under supergravity field. When the gravity coefficient G ≥ 50, the alloy samples were divided automatically into two parts: the upper residue and the lower filtered aluminum. All inclusions (MgAl2O4 and Al3Ti particles) were nearly intercepted in the upper residue by filter felt with average pore size of 44.78 μm. The removal efficiencies of oxide inclusions and Al3Ti particles exceeded 98 and 90 pct, respectively, at G ≥ 50, t = 2 minutes, T = 973 K (700 °C). Besides, the yield of purified aluminum was up to 92.1 pct at G = 600, t = 2 minutes, and T = 973 K (700 °C). The calculations of centrifugal pressure indicated that supergravity filtration could effectively overcome the pressure drop without meeting the rigorous requirement of height of molten metal, especially for using the fine-pore filter medium. Moreover, cake-mode filtration was the major mechanism of supergravity filtration of molten metal in this work.

  19. Uranium (III) precipitation in molten chloride by wet argon sparging

    Energy Technology Data Exchange (ETDEWEB)

    Vigier, Jean-François, E-mail: jean-francois.vigier@ec.europa.eu [CEA, Nuclear Energy Division, Radiochemistry & Processes Department, F-30207 Bagnols sur Cèze (France); Unité de Catalyse et de Chimie du Solide, UCCS UMR CNRS 8181, Univ. Lille Nord de France, ENSCL-USTL, B.P. 90108, 59652 Villeneuve d' Ascq Cedex (France); Laplace, Annabelle [CEA, Nuclear Energy Division, Radiochemistry & Processes Department, F-30207 Bagnols sur Cèze (France); Renard, Catherine [Unité de Catalyse et de Chimie du Solide, UCCS UMR CNRS 8181, Univ. Lille Nord de France, ENSCL-USTL, B.P. 90108, 59652 Villeneuve d' Ascq Cedex (France); Miguirditchian, Manuel [CEA, Nuclear Energy Division, Radiochemistry & Processes Department, F-30207 Bagnols sur Cèze (France); Abraham, Francis [Unité de Catalyse et de Chimie du Solide, UCCS UMR CNRS 8181, Univ. Lille Nord de France, ENSCL-USTL, B.P. 90108, 59652 Villeneuve d' Ascq Cedex (France)

    2016-06-15

    In the context of pyrochemical processes for nuclear fuel treatment, the precipitation of uranium (III) in molten salt LiCl-CaCl{sub 2} (30–70 mol%) at 705 °C is studied. First, this molten chloride is characterized with the determination of the water dissociation constant. With a value of 10{sup −4.0}, the salt has oxoacid properties. Then, the uranium (III) precipitation using wet argon sparging is studied. The salt is prepared using UCl{sub 3} precursor. At the end of the precipitation, the salt is totally free of solubilized uranium. The main part is converted into UO{sub 2} powder but some uranium is lost during the process due to the volatility of uranium chloride. The main impurity of the resulting powder is calcium. The consequences of oxidative and reductive conditions on precipitation are studied. Finally, coprecipitation of uranium (III) and neodymium (III) is studied, showing a higher sensitivity of uranium (III) than neodymium (III) to precipitation. - Highlights: • Precipitation of Uranium (III) is quantitative in molten salt LiCl-CaCl{sub 2} (30–70 mol%). • The salt is oxoacid with a water dissociation constant of 10{sup −4.0} at 705 °C. • Volatility of uranium chloride is strongly reduced in reductive conditions. • Coprecipitation of U(III) and Nd(III) leads to a consecutive precipitation of the two elements.

  20. CO2 decomposition using electrochemical process in molten salts

    Science.gov (United States)

    Otake, Koya; Kinoshita, Hiroshi; Kikuchi, Tatsuya; Suzuki, Ryosuke O.

    2012-08-01

    The electrochemical decomposition of CO2 gas to carbon and oxygen gas in LiCl-Li2O and CaCl2-CaO molten salts was studied. This process consists of electrochemical reduction of Li2O and CaO, as well as the thermal reduction of CO2 gas by the respective metallic Li and Ca. Two kinds of ZrO2 solid electrolytes were tested as an oxygen ion conductor, and the electrolytes removed oxygen ions from the molten salts to the outside of the reactor. After electrolysis in both salts, the aggregations of nanometer-scale amorphous carbon and rod-like graphite crystals were observed by transmission electron microscopy. When 9.7 %CO2-Ar mixed gas was blown into LiCl-Li2O and CaCl2-CaO molten salts, the current efficiency was evaluated to be 89.7 % and 78.5 %, respectively, by the exhaust gas analysis and the supplied charge. When a solid electrolyte with higher ionic conductivity was used, the current and carbon production became larger. It was found that the rate determining step is the diffusion of oxygen ions into the ZrO2 solid electrolyte.

  1. Prebiotic formation of polyamino acids in molten urea

    Science.gov (United States)

    Mita, H.; Nomoto, S.; Terasaki, M.; Shimoyama, A.; Yamamoto, Y.

    2005-04-01

    It is important for research into the origins of life to elucidate polyamino acid formation under prebiotic conditions. Only a limited set of amino acids has been reported to polymerize thermally. In this paper we demonstrate a novel thermal polymerization mechanism in a molten urea of alkylamino acids (i.e. glycine, alanine, β-alanine, α-aminobutyric acid, valine, norvaline, leucine and norleucine), which had been thought to be incapable of undergoing thermal polymerization. Also, aspartic acid was found to polymerize in molten urea at a lower temperature than that at which aspartic acid alone had previously been thermally polymerized. Individual oligomers produced in heating experiments on urea-amino acid mixtures were analysed using a liquid chromatograph mass spectrometer. Major products in the reaction mixture were three different types of polyamino acid derivatives: N-carbamoylpolyamino acids, polyamino acids containing a hydantoin ring at the N-terminal position and unidentified derivatives with molecular weights that were greater by 78 than those of the corresponding peptide forms. The polymerization reaction occurred by taking advantage of the high polarity of molten urea as well as its dehydrating ability. Under the presumed prebiotic conditions employed here, many types of amino acids were thus revealed to undergo thermal polymerization.

  2. Development of electrochemical separation methods from molten fluoride salts

    Energy Technology Data Exchange (ETDEWEB)

    Straka, M.; Tulackova, R.; Chuchvalcova Bimova, K. [Nuclear Research Institute Rez plc, 250 68 Husinec, Rez 130, (Czech Republic)

    2008-07-01

    Molten Salt Reactor (MSR) is liquid-fueled reactor that can be used for actinide burning, production of electricity, production of hydrogen, and production of fissile fuels (breeding). The MSR concept was identified, along with five other concepts, as a suitable candidate of cooperative development by the Generation IV International Forum (GIF). The MSR concept takes into account a circulating molten fluoride salts fuel mixture. Use of liquid fuel mixture results in possibility of its continuous (online) reprocessing. Within the proposed MSR fuel cycle, the electro-separation methods are considered as important techniques. The main aim of this work is to determine the electrochemical behaviour of selected actinides and lanthanides, which represents the fissile material and fission products, in suitable molten fluoride media as the general framework of our work is to verify the separation capability of the electrochemical methods and proposal of its integration into the MSR fuel cycle. Presented results were obtained by the method of cyclic voltammetry. The experimental set-up, preparation of the melt and results of selected measurements are presented in this paper and electrochemical behaviour of uranium and selected lanthanides are demonstrated by respective voltammograms evaluation. (authors)

  3. Conceptual design of Indian molten salt breeder reactor

    Indian Academy of Sciences (India)

    P K Vijayan; A Basak; I V Dulera; K K Vaze; S Basu; R K Sinha

    2015-09-01

    The third stage of Indian nuclear power programme envisages the use of thorium as the fertile material with 233U, which would be obtained from the operation of Pu/Th-based fast reactors in the later part of the second stage. Thorium-based reactors have been designed in many configurations, from light water-cooled designs to high-temperature liquid metal-cooled options. Another option, which holds promise, is the molten salt-fuelled reactor, which can be configured to give significant breeding ratios. A crucial part for achieving reasonable breeding in such reactors is the need to reprocess the salt continuously, either online or in batch mode. India has recently started carrying out fundamental studies so as to arrive at a conceptual design of Indian molten salt breeder reactor (IMSBR). Presently, various design options and possibilities are being studied from the point of view of reactor physics and thermal hydraulic design. In parallel, fundamental studies on natural circulation and corrosion behaviour of various molten salts have also been initiated.

  4. Isolated Fallopian Tube Torsion

    Directory of Open Access Journals (Sweden)

    S. Kardakis

    2013-01-01

    Full Text Available Isolated torsion of the Fallopian tube is a rare gynecological cause of acute lower abdominal pain, and diagnosis is difficult. There are no pathognomonic symptoms; clinical, imaging, or laboratory findings. A preoperative ultrasound showing tubular adnexal masses of heterogeneous echogenicity with cystic component is often present. Diagnosis can rarely be made before operation, and laparoscopy is necessary to establish the diagnosis. Unfortunately, surgery often is performed too late for tube conservation. Isolated Fallopian tube torsion should be suspected in case of acute pelvic pain, and prompt intervention is necessary.

  5. Experimental studies of thermal and chemical interactions between molten aluminum and water

    Energy Technology Data Exchange (ETDEWEB)

    Farahani, A.A.; Corradini, M.L. [Univ. of Wisconsin, Madison, WI (United States)

    1995-09-01

    The possibility of rapid physical and chemical aluminum/water interactions during a core melt accident in a noncommercial reactor (e.g., HFIR, ATR) has resulted in extensive research to determine the mechanism by which these interactions occur and propagate on an explosive time scale. These events have been reported in nuclear testing facilities, i.e., during SPERT 1D experiment, and also in aluminum casting industries. Although rapid chemical reactions between molten aluminum and water have been subject of many studies, very few reliable measurements of the extent of the chemical reactions have thus far been made. We have modified an existing 1-D shock tube facility to perform experiments in order to determine the extent of the explosive thermal/chemical interactions between molton aluminum and water by measuring important physical quantities such as the maximum dynamic pressure and the amount of the generated hydrogen. Experimental results show that transient pressures greater than 69 MPa with a rise time of less than 125 {mu}sec can occur as the result of the chemical reaction of 4.2 grams of molton aluminum (approximately 15% of the total mass of the fuel of 28 grams) at 980 C with room temperature water.

  6. Mathematical Modeling of the Vacuum Circulation Refining Processof Molten Steel

    Institute of Scientific and Technical Information of China (English)

    魏季和

    2003-01-01

    The available studies in the literature on mathematical modeling of the vacuum circulation (RH) refining process of molten steel have briefly been reviewed. The latest advances obtained by the author with his research group have been Summarized. On the basis of the mass and momentum balances in the system, a new mathematical model for decarburization and degassing during the RH and RH-KTB refining processes of molten steel was proposed and developed. The refining roles of the three reaction sites, i.e. the up-snorkel zone, the droplet group and steel bath in the vacuum vessel, were considered in the model. It was assumed that the mass transfer of reactive components in the molten steel is the rate control step of the refining reactions. And the friction losses and drags of flows in the snorkels and vacuum vessel were all counted. The model was applied to the refining of molten steel in a multifunction RH degasser of 90 t capacity. The decarburization and degassing processes in the degasser under the RH and RH-KTB operating condi-tions were modeled and analyzed using this model. Besides, proceeded from the two-resistance mass transfer theory and the mass bal-ance of sulphur in the system, a kinetic model for the desulphurization by powder injection and blowing in the RH refining of molten steel was developed. Modeling and predictions of the process of injecting and blowing the lime based powder flux under assumed oper-ating modes with the different initial contents of sulphur and amounts of powder injected and blown in a RH degasser of 300 t capacity were carried out using the model. It was demonstrated that for the RH and RH-KTB refining processes, and the desulphurization by powder injection and blowing in the RH refining, the results predicted by the models were all in good agreement respectively with data from industrial experiments and practice. These models may be expected to offer some useful information and a reliable basis for de-termining and optimizing

  7. Tube-Forming Assays.

    Science.gov (United States)

    Brown, Ryan M; Meah, Christopher J; Heath, Victoria L; Styles, Iain B; Bicknell, Roy

    2016-01-01

    Angiogenesis involves the generation of new blood vessels from the existing vasculature and is dependent on many growth factors and signaling events. In vivo angiogenesis is dynamic and complex, meaning assays are commonly utilized to explore specific targets for research into this area. Tube-forming assays offer an excellent overview of the molecular processes in angiogenesis. The Matrigel tube forming assay is a simple-to-implement but powerful tool for identifying biomolecules involved in angiogenesis. A detailed experimental protocol on the implementation of the assay is described in conjunction with an in-depth review of methods that can be applied to the analysis of the tube formation. In addition, an ImageJ plug-in is presented which allows automatic quantification of tube images reducing analysis times while removing user bias and subjectivity.

  8. Chest tube insertion - slideshow

    Science.gov (United States)

    ... presentations/100008.htm Chest tube insertion - series—Normal anatomy To use the sharing features ... pleural space is the space between the inner and outer lining of the lung. It is normally very thin, and lined only ...

  9. Snorkeling and Jones tubes

    OpenAIRE

    Lam, Lewis Y. W.; Weatherhead, Robert G.

    2015-01-01

    We report a case of tympanic membrane rupture during snorkeling in a 17-year-old young man who had previously undergone bilateral Jones tubes placed for epiphora. To our knowledge, this phenomenon has not been previously reported.

  10. Snorkeling and Jones tubes.

    Science.gov (United States)

    Lam, Lewis Y W; Weatherhead, Robert G

    2015-01-01

    We report a case of tympanic membrane rupture during snorkeling in a 17-year-old young man who had previously undergone bilateral Jones tubes placed for epiphora. To our knowledge, this phenomenon has not been previously reported.

  11. Nasogastric feeding tube

    Science.gov (United States)

    ... page: //medlineplus.gov/ency/patientinstructions/000182.htm Nasogastric feeding tube To use the sharing features on this ... the nose. It can be used for all feedings or for giving a person extra calories. It ...

  12. Ear tube insertion - slideshow

    Science.gov (United States)

    ... this page: //medlineplus.gov/ency/presentations/100045.htm Ear tube insertion - series—Normal anatomy To use the ... 4 Overview The eardrum (tympanic membrane) separates the ear canal from the middle ear. Review Date 8/ ...

  13. Kinking of medical tubes.

    Science.gov (United States)

    Ingles, David

    2004-05-01

    The phenomenon of kinking in medical tubing remains a problem for some applications, particularly critical ones such as transporting gasses or fluids. Design features are described to prevent its occurrence.

  14. Effect of electromagnetic force on turbulent flow of molten metal in aluminum electrolysis cells

    Institute of Scientific and Technical Information of China (English)

    周萍; 梅炽; 周乃君; 姜昌伟

    2004-01-01

    The standard k-ε model was adopted to simulate the flow field of molten metal in three aluminum electrolysis cells with different anode risers. The Hartman number, Reynolds number and the turbulent Reynolds number of molten metal were calculated quantitatively. The turbulent Reynolds number is in the order of 103 , and Reynolds number is in the order of 104 if taking the depth of molten metal as the characteristic length. The results show that the molten metal flow is the turbulence of high Reynolds number, the turbulent Reynolds number is more appropriate than Reynolds number to be used to describe the turbulent characteristic of molten metal, and Hartman number displays very well that electromagnetic force inhibits turbulent motion of molten metal.

  15. Physical Modeling of the Vacuum Circulation Refining Process of Molten Steel

    Institute of Scientific and Technical Information of China (English)

    魏季和

    2003-01-01

    The available studies in the literature on physical modeling of the vacuum circulation (RH, i.e. Ruhrstahl-Heraeus) refining process of molten steel have briefly been reviewed. The latest advances made by the author with his research group have been summarized. Water modeling was employed to investigate the flow and mixing characteristics of molten steel under the RH and RH-KTB (Kawasaki top blowing) conditions and the mass transfer features between molten steel and powder particles in the RH-PTB (powder top blowing) refining. The geometric similarity ratio between the model and its prototype (a multifunction RH degasser of 90 t capacity) was 1:5. The effects of the related technological and structural factors were considered. These latest studies have revealed the flow and mixing characteristics of molten steel and the mass transfer features between molten steel and powder particles in these processes, and have provided a better understanding of the refining processes of molten steel.

  16. Ionic Conductivities of Molten CuI and AgI-CuI Mixtures

    Science.gov (United States)

    Tahara, Shuta; Shimakura, Hironori; Ohno, Satoru; Fukami, Takanori

    2017-08-01

    Ionic conductivities σ for molten CuI and AgI-CuI mixtures were measured in the temperature ranges of approximately 580-800 and 500-850 °C, respectively. The value of σ for molten CuI in the range is smaller than that for molten CuBr and CuCl. σ for molten AgI-CuI mixtures decreases with increasing CuI-concentration. The activation energies Ea for molten AgI-CuI system were determined from the analysis of temperature dependence of σ by using the by Arrhenius type equation. Ea for molten AgI-CuI gradually increase with increasing CuIconcentration.

  17. Using a nasogastric tube.

    Science.gov (United States)

    Candy, C

    1986-09-01

    This discussion of the use of a nasogastric tube covers the equipment needed, the method, rehydration and feeding, prolonged nasogastric feeding, and stopping nasogastric feeding. A nasogastric tube is useful when children are unable to drink safely and in sufficient amounts for any of the following reasons: severe dehydration; if intravenous (IV) therapy is unavailable; low birth weight infants; or the child is drowsy or vomiting. Severely malnourished children may be fed initially in this way if they are too weak or anorexic to eat or drink normally. The following equipment is needed: nasogastric tube; lubricating fluid; a syringe; blue litmus paper, if available; adhesive tape; stethoscope if available; and fluid to be given. Explain to the child's parents and the child, if old enough to understand, what will be done; lie infants flat; measure the approximate length from the child's nostril to the ear lobe and then to the top of the abdomen with the tube and mark the position; clean the nostrils to remove the mucus, and lubricate the tip of the tube and gently insert into the nostril; give the child a drink of water if he or she is conscious; continue to pass the tube down until the position marked reaches the nostril; use the syringe to suck up some fluid and test with blue litmus paper to check that the tube is in the stomach; and inject 5-10 ml of fluid (saline or oral rehydration solution, not milk formula) by syringe if satisfied the tube is in the correct position. Where possible, give a continuous drip of fluid. If this is not possible, give frequent small amounts using the syringe as a funnel. If feeding continues for more than 24 hours, clean the nostrils daily with warm water and change the tube to the other nostril every few days. Also keep the mouth very clean with a dilute solution of 8% sodium bicarbonate, if available, or citrus fruit juice. To remove the tube, remove the adhesive tape, take the tube out gently and smoothly, and offer the child a

  18. Magnesium tube hydroforming

    Energy Technology Data Exchange (ETDEWEB)

    Liewald, M.; Pop, R. [Institute for Metal Forming Technology (IFU), Stuttgart (Germany)

    2008-04-15

    Magnesium alloys reveal a good strength-to-weight ratio in the family of lightweight metals and gains potential to provide up to 30% mass savings compared to aluminium and up to 75 % compared to steel. The use of sheet magnesium alloys for auto body applications is however limited due to the relatively low formability at room temperature. Within the scope of this paper, extruded magnesium tubes, which are suitable for hydroforming applications, have been investigated. Results obtained at room temperature using magnesium AZ31 tubes show that circumferential strains are limited to a maximal value of 4%. In order to examine the influence of the forming temperature on tube formability, investigations have been carried out with a new die set for hot internal high pressure (IHP) forming at temperatures up to 400 C. Earlier investigations with magnesium AZ31 tubes have shown that fractures occur along the welding line at tubes extruded over a spider die, whereby a non-uniform expansion at bursting with an elongation value of 24% can be observed. A maximum circumferential strain of approx. 60% could be attained when seamless, mechanically pre-expanded and annealed tubes of the same alloy have been used. The effect of annealing time on materials forming properties shows a fine grained structure for sufficient annealing times as well as deterioration with a large increase at same time. Hence, seamless ZM21 tubes have been used in the current investigations. With these tubes, an increased tensile fracture strain of 116% at 350 C is observed as against 19% at 20 C, obtained by tensile testing of milled specimens from the extruded tubes. This behaviour is also seen under the condition of tool contact during the IHP forming process. To determine the maximum circumferential strain at different forming temperatures and strain rates, the tubes are initially bulged in a die with square cross-section under plane stress conditions. Thereafter, the tubes are calibrated by using an

  19. Power vacuum tubes handbook

    CERN Document Server

    Whitaker, Jerry

    2012-01-01

    Providing examples of applications, Power Vacuum Tubes Handbook, Third Edition examines the underlying technology of each type of power vacuum tube device in common use today. The author presents basic principles, reports on new development efforts, and discusses implementation and maintenance considerations. Supporting mathematical equations and extensive technical illustrations and schematic diagrams help readers understand the material. Translate Principles into Specific Applications This one-stop reference is a hands-on guide for engineering personnel involved in the design, specification,

  20. Experimental Demonstration of the Molten Oxide Electrolysis Method for Oxygen and Iron Production from Simulated Lunar Materials

    Science.gov (United States)

    Curreri, P. A.; Ethridge, E.; Hudson, S.; Sen, S.

    2006-01-01

    This paper presents the results of a Marshall Space Flight Center funded effort to conduct an experimental demonstration of the processing of simulated lunar resources by the molten oxide electrolysis (MOE) process to produce oxygen and metal from lunar resources to support human exploration of space. Oxygen extracted from lunar materials can be used for life support and propellant, and silicon and metallic elements produced can be used for in situ fabrication of thin-film solar cells for power production. The Moon is rich in mineral resources, but it is almost devoid of chemical reducing agents, therefore, molten oxide electrolysis, MOE, is chosen for extraction, since the electron is the most practical reducing agent. MOE was also chosen for following reasons. First, electrolytic processing offers uncommon versatility in its insensitivity to feedstock composition. Secondly, oxide melts boast the twin key attributes of highest solubilizing capacity for regolith and lowest volatility of any candidate electrolytes. The former is critical in ensuring high productivity since cell current is limited by reactant solubility, while the latter simplifies cell design by obviating the need for a gas-tight reactor to contain evaporation losses as would be the case with a gas or liquid phase fluoride reagent operating at such high temperatures. In the experiments reported here, melts containing iron oxide were electrolyzed in a low temperature supporting oxide electrolyte (developed by D. Sadoway, MIT).

  1. Characterization of ultrafine-grained aluminum tubes processed by Tube Cyclic Extrusion–Compression (TCEC)

    Energy Technology Data Exchange (ETDEWEB)

    Babaei, A., E-mail: A_babaei@ut.ac.ir; Mashhadi, M.M.

    2014-09-15

    Tube Cyclic Extrusion–Compression as a novel severe plastic deformation technique for tubes was utilized for processing ultrafine grained 1050 aluminum alloy for the first time. In this method, aluminum tube is fully constrained and deformed between mandrel and chamber with a small neck zone. The material deformation during Tube Cyclic Extrusion–Compression processing analyzed and the grain refinement mechanism were described. The capability of Tube Cyclic Extrusion–Compression in grain refinement of the aluminum alloy was demonstrated by transmission electron microscopy observations and X-ray diffraction line profile analysis. The micrographs of the evolved microstructure show grain size of 850 nm and 550 nm after the first and second processing cycles of Tube Cyclic Extrusion–Compression, respectively. Mechanical properties of the initial and processed specimens were extracted from ring-hoop tensile tests. The documented results confirm grain refinement by showing remarkable increase in the yield and ultimate strengths. The main increase in strength and decrease in elongation take place after the first cycle. The microhardness assessments illustrate increase from the initial value of 29 Hv to 44 and 49 Hv respectively after the first and second cycles of Tube Cyclic Extrusion–Compression. There is a good homogeneity in peripheral microhardness and microhardness across the tube thickness. - Highlights: • Tubes of AA1050 for the first time were successfully SPD processed by TCEC. • The grain size was refined to 550 nm after two cycles of TCEC. • Notable increase in the strength and decrease in the elongation were documented. • The microhardness increased to 49 Hv from the initial value of 29 Hv. • Good homogeneity in the microhardness distribution was recorded.

  2. Hybrid Molten Bed Gasifier for High Hydrogen Syngas Production

    Energy Technology Data Exchange (ETDEWEB)

    Rue, David [Gas Technology Institute, Des Plaines, IL (United States)

    2017-05-23

    The techno-economic analyses of the hybrid molten bed gasification technology and laboratory testing of the HMB process were carried out in this project by the Gas Technology Institute and partner Nexant, Inc. under contract with the US Department of Energy’s National Energy Technology Laboratory. This report includes the results of two complete IGCC and Fischer-Tropsch TEA analyses comparing HMB gasification with the Shell slagging gasification process as a base case. Also included are the results of the laboratory simulation tests of the HMB process using Illinois #6 coal fed along with natural gas, two different syngases, and steam. Work in this 18-month project was carried out in three main Tasks. Task 2 was completed first and involved modeling, mass and energy balances, and gasification process design. The results of this work were provided to Nexant as input to the TEA IGCC and FT configurations studied in detail in Task 3. The results of Task 2 were also used to guide the design of the laboratory-scale testing of the HMB concept in the submerged combustion melting test facility in GTI’s industrial combustion laboratory. All project work was completed on time and budget. A project close-out meeting reviewing project results was conducted on April 1, 2015 at GTI in Des Plaines, IL. The hybrid molten bed gasification process techno-economic analyses found that the HMB process is both technically and economically attractive compared with the Shell entrained flow gasification process. In IGCC configuration, HMB gasification provides both efficiency and cost benefits. In Fischer-Tropsch configuration, HMB shows small benefits, primarily because even at current low natural gas prices, natural gas is more expensive than coal on an energy cost basis. HMB gasification was found in the TEA to improve the overall IGCC economics as compared to the coal only Shell gasification process. Operationally, the HMB process proved to be robust and easy to operate. The burner

  3. Molten salt synthesis of sodium lithium titanium oxide anode material for lithium ion batteries

    Energy Technology Data Exchange (ETDEWEB)

    Yin, S.Y., E-mail: yshy2004@hotmail.com [College of Environmental and Biological Engineering, Wuhan Technology and Business University, Wuhan 430065 (China); Feng, C.Q. [Hubei Collaborative Innovation Center for Advanced Organic Chemical Materials, Ministry of Education Key Laboratory for Synthesis and Applications of Organic Functional Molecules, Hubei University, Wuhan 430062 (China); Wu, S.J.; Liu, H.L.; Ke, B.Q. [College of Environmental and Biological Engineering, Wuhan Technology and Business University, Wuhan 430065 (China); Zhang, K.L. [College of Chemistry and Molecular Sciences, Wuhan University, Wuhan 430072 (China); Chen, D.H. [College of Environmental and Biological Engineering, Wuhan Technology and Business University, Wuhan 430065 (China); Hubei Key Laboratory for Catalysis and Material Science, College of Chemistry and Material Science, South Central University for Nationalities, Wuhan 430074, Hubei (China)

    2015-09-05

    Highlights: • Na{sub 2}Li{sub 2}Ti{sub 6}O{sub 12} has been successfully synthesized via a molten salt route. • Calcination temperature is an important effect on the component and microstructure of the product. • Pure phase Na{sub 2}Li{sub 2}Ti{sub 6}O{sub 12} could be obtained at 700 °C for 2 h. - Abstract: The sodium lithium titanium oxide with composition Na{sub 2}Li{sub 2}Ti{sub 6}O{sub 14} has been synthesized by a molten salt synthesis method using sodium chloride and potassium chloride mixture as a flux medium. Synthetic variables on the synthesis, such as sintering temperature, sintering time and the amount of lithium carbonate, were intensively investigated. Powder X-ray diffraction and scanning electron microscopy images of the reaction products indicates that pure phase sodium lithium titanium oxide has been obtained at 700 °C, and impure phase sodium hexatitanate with whiskers produced at higher temperature due to lithium evaporative losses. The results of cyclic voltammetry and discharge–charge tests demonstrate that the synthesized products prepared at various temperatures exhibited electrochemical diversities due to the difference of the components. And the sample obtained at 700 °C revealed highly reversible insertion and extraction of Li{sup +} and displayed a single potential plateau at around 1.3 V. The product obtained at 700 °C for 2 h exhibits good cycling properties and retains the specific capacity of 62 mAh g{sup −1} after 500 cycles.

  4. Aeronautical tubes and pipes

    Science.gov (United States)

    Beauclair, N.

    1984-12-01

    The main and subcomponent French suppliers of aircraft tubes and pipes are discussed, and the state of the industry is analyzed. Quality control is essential for tubes with regard to their i.d. and metallurgical compositions. French regulations do not allow welded seam tubes in hydraulic circuits unless no other form is available, and then rustproofed steel must be installed. The actual low level of orders for any run of tubes dictates that the product is only one of several among the manufacturers' line. Automation, both in NDT and quality control, assures that the tubes meet specifications. A total of 10 French companies participate in the industry, serving both civil and military needs, with some companies specializing only in titanium, steel, or aluminum materials. Concerns wishing to enter the market must upgrade their equipment to meet the higher aeronautical specifications and be prepared to furnish tubes and pipes that serve both functional and structural purposes simultaneously. Additionally, pipe-bending machines must also perform to tight specifications. Pipes can range from 0.2 mm exterior diameter to 40 mm, with wall thicknesses from 0.02 mm to 3 mm. A chart containing a list of manufacturers and their respective specifications and characteristics is presented, and a downtrend in production with reduction of personnel is noted.

  5. A gas laser tube

    Energy Technology Data Exchange (ETDEWEB)

    Tetsuo, F.; Tokhikhide, N.

    1984-04-19

    A gas laser tube is described in which contamination of the laser gas mixture by the coolant is avoided, resulting in a longer service life of the mirrors. The holder contains two tubes, one inside the other. The laser gas mixture flows through the internal tube. An electrode is fastened to the holder. The coolant is pumped through the slot between the two tubes, for which a hole is cut into the holder. The external tube has a ring which serves to seal the cavity containing the coolant from the atmosphere. The internal tube has two rings, one to seal the laser gas mixture and the other to seal the coolant. A slot is located between these two rings, which leads to the atmosphere (the atmosphere layer). With this configuration, the degradation of the sealing properties of the internal ring caused by interaction with the atmospheric layer is not reflected in the purity of the laser gas mixture. Moreover, pollution of the mirrors caused by the penetration of the coolant into the cavity is eliminated.

  6. Dynamic tube/support interaction in heat exchanger tubes

    Energy Technology Data Exchange (ETDEWEB)

    Chen, S.S.

    1991-01-01

    The supports for heat exchanger tubes are usually plates with drilled holes; other types of supports also have been used. To facilitate manufacture and to allow for thermal expansion of the tubes, small clearances are used between tubes and tube supports. The dynamics of tube/support interaction in heat exchangers is fairly complicated. Understanding tube dynamics and its effects is important for heat exchangers. This paper summarizes the current state of the art on this subject and to identify future research needs. Specifically, the following topics are discussed: dynamics of loosely supported tubes, tube/support gap dynamics, tube response in flow, tube damage and wear, design considerations, and future research needs. 55 refs., 1 fig.

  7. Molten pool-lower head integrity. Heat transfer models including advanced numerical simulations (DNS)

    Energy Technology Data Exchange (ETDEWEB)

    Seiler, J.M.; Bonnet, J.M.; Bernaz, L. [CEA Grenoble (France)

    2001-07-01

    Extensive studies have been performed to investigate the heat transfer within a molten corium pool (homogeneous, stratified and with miscibility gap): Synthesis of heat transfer correlations in molten pool (homogeneous and stratified), Focusing effect in stratified metal layer, DNS analysis of Rayleigh Benard instabilities at the top boundary; interpretation of the different convection regimes and exponents affecting the Rayleigh number in the heat transfer correlations, Molten pool model for corium presenting a miscibility gap. Condition for de-stratification. (authors)

  8. Automated addition of Chelex solution to tubes containing trace items

    DEFF Research Database (Denmark)

    Stangegaard, Michael; Hansen, Thomas Møller; Hansen, Anders Johannes;

    2011-01-01

    Extraction of DNA from trace items for forensic genetic DNA typing using a manual Chelex based extraction protocol requires addition of Chelex solution to sample tubes containing trace items. Automated of addition of Chelex solution may be hampered by high viscosity of the solution and fast sedim...

  9. Automated addition of Chelex solution to tubes containing trace items

    DEFF Research Database (Denmark)

    Stangegaard, Michael; Hansen, Thomas Møller; Hansen, Anders Johannes;

    2011-01-01

    Extraction of DNA from trace items for forensic genetic DNA typing using a manual Chelex based extraction protocol requires addition of Chelex solution to sample tubes containing trace items. Automated of addition of Chelex solution may be hampered by high viscosity of the solution and fast...

  10. Core-concrete molten pool dynamics and interfacial heat transfer. [PWR; BWR

    Energy Technology Data Exchange (ETDEWEB)

    Benjamin, A.S.

    1980-01-01

    Theoretical models are derived for the heat transfer from molten oxide pools to an underlying concrete surface and from molten steel pools to a general concrete containment. To accomplish this, two separate effects models are first developed, one emphasizing the vigorous agitation of the molten pool by gases evolving from the concrete and the other considering the insulating effect of a slag layer produced by concrete melting. The resulting algebraic expressions, combined into a general core-concrete heat transfer representation, are shown to provide very good agreement with experiments involving molten steel pours into concrete crucibles.

  11. Role of molten salt flux in melting of used beverage container (UBC) scrap

    Energy Technology Data Exchange (ETDEWEB)

    Ye, J.; Sahai, Y. [Ohio State Univ., Columbus, OH (United States). Dept. of Materials Science and Engineering

    1995-12-31

    Recycling of aluminum scrap, such as Used Beverage Container (UBC) scrap is steadily increasing. In secondary remelting of such scrap, it is a common practice to use protective molten salt cover. An appropriate salt protects metal from oxidation, promotes coalescence of the suspended metal droplets, and separates clean metal from the oxide contamination. The molten salt also reacts with metal. This causes metal loss and change of resulting metal composition. In this paper, role of molten salt fluxes in melting of UBC scrap is discussed, and selection criteria for molten salt are provided.

  12. NEI You Tube Videos: Amblyopia

    Medline Plus

    Full Text Available ... search for current job openings visit HHS USAJobs Home > NEI YouTube Videos > NEI YouTube Videos: Amblyopia NEI YouTube Videos YouTube Videos Home Age-Related Macular Degeneration Amblyopia Animations Blindness Cataract ...

  13. Study on Thermal Storage Process of Solar Energy in Molten Salt Thermal Storage Tank%太阳能熔盐蓄热罐蓄热过程的性能研究

    Institute of Scientific and Technical Information of China (English)

    王兴; 靳智平; 刘宏丽

    2015-01-01

    By using numerical simulation method, the melting and thermal storage process of molten salt in the thermal storage tank was studied. The results showed that tubes pitches have important influence on the melting process of molten salt in the same thermal storage tank. The tank with 200 mm tubes pitches is of better storage ability than that with 120 mm, and the temperature distribution in molten salt tank is more uniform. The results will provide a reference to the structural design and optimization of the thermal storage tank.%对太阳能熔盐蓄热罐的熔化和蓄热过程进行了数值模拟研究,结果表明相同蓄热罐不同的加热内管间距对熔化和蓄热过程有着显著影响.其中,200 mm管间距的蓄热罐熔化和蓄热过程较管间距为120 mm的蓄热快,并且温度分布比较均匀.研究结论对蓄热罐的结构设计和优化运行具有一定的参考价值.

  14. Management of chest drainage tubes after lung surgery.

    Science.gov (United States)

    Satoh, Yukitoshi

    2016-06-01

    Since chest tubes have been routinely used to drain the pleural space, particularly after lung surgery, the management of chest tubes is considered to be essential for the thoracic surgeon. The pleural drainage system requires effective drainage, suction, and water-sealing. Another key point of chest tube management is that a water seal is considered to be superior to suction for most air leaks. Nowadays, the most common pleural drainage device attached to the chest tube is the three-bottle system. An electronic chest drainage system has been developed that is effective in standardizing the postoperative management of chest tubes. More liberal use of digital drainage devices in the postoperative management of the pleural space is warranted. The removal of chest tubes is a common procedure occurring almost daily in hospitals throughout the world. Extraction of the tube is usually done at the end of full inspiration or at the end of full expiration. The tube removal technique is not as important as how it is done and the preparation for the procedure. The management of chest tubes must be based on careful observation, the patient's characteristics, and the operative procedures that had been performed.

  15. Effect of tube size on electromagnetic tube bulging

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    The commercial finite code ANSYS was employed for the simulation of the electromagnetic tube bulging process. The finite element model and boundary conditions were thoroughly discussed. ANSYS/EMAG was used to model the time varying electromagnetic field in order to obtain the radial and axial magnetic pressure acting on the tube. The magnetic pressure was then used as boundary conditions to model the high velocity deformation of various length tube with ANSYS/LSDYNA. The time space distribution of magnetic pressure on various length tubes was presented. Effect of tube size on the distribution of radial magnetic pressure and axial magnetic pressure and high velocity deformation were discussed. According to the radial magnetic pressure ratio of tube end to tube center and corresponding dimensionless length ratio of tube to coil, the free electromagnetic tube bulging was studied in classification. The calculated results show good agreements with practice.

  16. A new anode material for oxygen evolution in molten oxide electrolysis.

    Science.gov (United States)

    Allanore, Antoine; Yin, Lan; Sadoway, Donald R

    2013-05-16

    Molten oxide electrolysis (MOE) is an electrometallurgical technique that enables the direct production of metal in the liquid state from oxide feedstock, and compared with traditional methods of extractive metallurgy offers both a substantial simplification of the process and a significant reduction in energy consumption. MOE is also considered a promising route for mitigation of CO2 emissions in steelmaking, production of metals free of carbon, and generation of oxygen for extra-terrestrial exploration. Until now, MOE has been demonstrated using anode materials that are consumable (graphite for use with ferro-alloys and titanium) or unaffordable for terrestrial applications (iridium for use with iron). To enable metal production without process carbon, MOE requires an anode material that resists depletion while sustaining oxygen evolution. The challenges for iron production are threefold. First, the process temperature is in excess of 1,538 degrees Celsius (ref. 10). Second, under anodic polarization most metals inevitably corrode in such conditions. Third, iron oxide undergoes spontaneous reduction on contact with most refractory metals and even carbon. Here we show that anodes comprising chromium-based alloys exhibit limited consumption during iron extraction and oxygen evolution by MOE. The anode stability is due to the formation of an electronically conductive solid solution of chromium(iii) and aluminium oxides in the corundum structure. These findings make practicable larger-scale evaluation of MOE for the production of steel, and potentially provide a key material component enabling mitigation of greenhouse-gas emissions while producing metal of superior metallurgical quality.

  17. Categorising YouTube

    Directory of Open Access Journals (Sweden)

    Thomas Mosebo Simonsen

    2011-09-01

    Full Text Available This article provides a genre analytical approach to creating a typology of the User Generated Content (UGC of YouTube. The article investigates the construction of navigationprocesses on the YouTube website. It suggests a pragmatic genre approach that is expanded through a focus on YouTube’s technological affordances. Through an analysis of the different pragmatic contexts of YouTube, it is argued that a taxonomic understanding of YouTube must be analysed in regards to the vacillation of a user-driven bottom-up folksonomy and a hierarchical browsing system that emphasises a culture of competition and which favours the already popular content of YouTube. With this taxonomic approach, the UGC videos are registered and analysed in terms of empirically based observations. The article identifies various UGC categories and their principal characteristics. Furthermore, general tendencies of the UGC within the interacting relationship of new and old genres are discussed. It is argued that the utility of a conventional categorical system is primarily of analytical and theoretical interest rather than as a practical instrument.

  18. Sensitivity and Uncertainty Study for Thermal Molten Salt Reactors

    Science.gov (United States)

    Bidaud, Adrien; Ivanona, Tatiana; Mastrangelo, Victor; Kodeli, Ivo

    2006-04-01

    The Thermal Molten Salt Reactor (TMSR) using the thorium cycle can achieve the GEN IV objectives of economy, safety, non-proliferation and durability. Its low production of higher actinides, coupled with its breeding capabilities - even with a thermal spectrum - are very valuable characteristics for an innovative reactor. Furthermore, the thorium cycle is more flexible than the uranium cycle since only a small fissile inventory (reactor. The potential of these reactors is currently being extensively studied at the CNRS and EdF /1,2/. A simplified chemical reprocessing is envisaged compared to that used for the former Molten Salt Breeder Reactor (MSBR). The MSBR concept was developed at Oak Ridge National Laboratory (ORNL) in the 1970's based on the Molten Salt Reactor Experiment (MSRE). The main goals of our current studies are to achieve a reactor concept that enables breeding, improved safety and having chemical reprocessing needs reduced and simplified as much as reasonably possible. The neutronic properties of the new TMSR concept are presented in this paper. As the temperature coefficient is close to zero, we will see that the moderation ratio cannot be chosen to simultaneously achieve a high breeding ratio, long graphite lifetime and low uranium inventory. It is clear that any safety margin taken due to uncertainty in the nuclear data will significantly reduce the capability of this concept, thus a sensitivity analysis is vital to propose measurements which would allow to reduce at present high uncertainties in the design parameters of this reactor. Two methodologies, one based on OECD/NEA deterministic codes and one on IPPE (Obninsk) stochastic code, are compared for keff sensitivity analysis. The uncertainty analysis of keff using covariance matrices available in evaluated files has been performed. Furthermore, a comparison of temperature coefficient sensitivity profiles is presented for the most important reactions. These results are used to review the

  19. STRUCTURING & RHEOLOGY OF MOLTEN POLYMER/CLAY NANOCOMPOSITES

    Institute of Scientific and Technical Information of China (English)

    Yuan-ze Xu; Yi-bin Xu

    2005-01-01

    The evolution and the origin of "solid-like state" in molten polymer/clay nanocomposites are studied. Using polypropylene/clay hybrid (PPCH) with sufficient maleic anhydride modified PP (PP-MA) as compatibilizer, well exfoliation yet solid-like state was achieved after annealing in molten state. Comprehensive linear viscoelasticity and non-linear rheological behaviors together with WAXD and TEM are studied on PPCH at various dispersion stages focusing on time,temperature and deformation dependencies of the "solid-like" state in molten nanocomposites. Based on these, it is revealed that the solid-structure is developed gradually along with annealing through the stages of inter-layer expansion by PP-MA,the diffusion and association of exfoliated silicate platelets, the formation of band/chain structure and, finally, a percolated clay associated network, which is responsible for the melt rigidity or solid-like state. The network will be broken down by melt frozen/crystallization and weakened at large shear or strong flow and, even more surprisingly, may be disrupted by using trace amount of silane coupling agent which may block the edge interaction of platelets. The solid-like structure causes characteristic non-linear rheological behaviors, e.g. residual stress after step shear, abnormal huge stress overshoots in step flows and, most remarkably, the negative first normal stress functions in steady shear or step flows. The rheological and structural arguments challenge the existing models of strengthened entangled polymer network by tethered polymer chains connecting clay particles or by chains in confined melts or frictional interaction among tactoids. A scheme of percolated networking of associated clay platelets, which may in band form of edge connecting exfoliated platelets, is suggested to explain previous experimental results.

  20. Tracheostomy tubes and related appliances.

    Science.gov (United States)

    Hess, Dean R

    2005-04-01

    Tracheostomy tubes are used to administer positive-pressure ventilation, to provide a patent airway, to provide protection from aspiration, and to provide access to the lower respiratory tract for airway clearance. They are available in a variety of sizes and styles, from several manufacturers. The dimensions of tracheostomy tubes are given by their inner diameter, outer diameter, length, and curvature. Differences in length between tubes of the same inner diameter, but from different manufacturers, are not commonly appreciated but may have important clinical implications. Tracheostomy tubes can be angled or curved, a feature that can be used to improve the fit of the tube in the trachea. Extra proximal length tubes facilitate placement in patients with large necks, and extra distal length tubes facilitate placement in patients with tracheal anomalies. Several tube designs have a spiral wire reinforced flexible design and have an adjustable flange design to allow bedside adjustments to meet extra-length tracheostomy tube needs. Tracheostomy tubes can be cuffed or uncuffed. Cuffs on tracheostomy tubes include high-volume low-pressure cuffs, tight-to-shaft cuffs, and foam cuffs. The fenestrated tracheostomy tube has an opening in the posterior portion of the tube, above the cuff, which allows the patient to breathe through the upper airway when the inner cannula is removed. Tracheostomy tubes with an inner cannula are called dual-cannula tracheostomy tubes. Several tracheostomy tubes are designed specifically for use with the percutaneous tracheostomy procedure. Others are designed with a port above the cuff that allows for subglottic aspiration of secretions. The tracheostomy button is used for stoma maintenance. It is important for clinicians caring for patients with a tracheostomy tube to understand the nuances of various tracheostomy tube designs and to select a tube that appropriately fits the patient.

  1. CAPTURING EXHAUST CO2 GAS USING MOLTEN CARBONATE FUEL CELLS

    Directory of Open Access Journals (Sweden)

    Prateek Dhawan

    2016-03-01

    Full Text Available Carbon dioxide is considered as one of the major contenders when the question of greenhouse effect arises. So for any industry or power plant it is of utmost importance to follow certain increasingly stringent environment protection rules and laws. So it is significant to keep eye on any possible methods to reduce carbon dioxide emissions in an efficient way. This paper reviews the available literature so as to try to provide an insight of the possibility of using Molten Carbonate Fuel Cells (MCFCs as the carbon capturing and segregating devices and the various factors that affect the performance of MCFCs during the process of CO2 capture.

  2. Precipitation of lamellar gold nanocrystals in molten polymers

    Science.gov (United States)

    Palomba, M.; Carotenuto, G.

    2016-05-01

    Non-aggregated lamellar gold crystals with regular shape (triangles, squares, pentagons, etc.) have been produced by thermal decomposition of gold chloride (AuCl) molecules in molten amorphous polymers (polystyrene and poly(methyl methacrylate)). Such covalent inorganic gold salt is high soluble into non-polar polymers and it thermally decomposes at temperatures compatible with the polymer thermal stability, producing gold atoms and chlorine radicals. At the end of the gold precipitation process, the polymer matrix resulted chemically modified because of the partial cross-linking process due to the gold atom formation reaction.

  3. Diffusion Welding of Alloys for Molten Salt Service - Status Report

    Energy Technology Data Exchange (ETDEWEB)

    Denis Clark; Ronald Mizia; Piyush Sabharwall

    2012-09-01

    The present work is concerned with heat exchanger development for molten salt service, including the proposed molten salt reactor (MSR), a homogeneous reactor in which the fuel is dissolved in a circulating fluid of molten salt. It is an outgrowth of recent work done under the Next Generation Nuclear Plant (NGNP) program; what the two reactor systems have in common is an inherently safe nuclear plant with a high outlet temperature that is useful for process heat as well as more conventional generation The NGNP program was tasked with investigating the application of a new generation of nuclear power plants to a variety of energy needs. One baseline reactor design for this program is a high temperature, gas-cooled reactor (HTGR), which provides many options for energy use. These might include the conventional Rankine cycle (steam turbine) generation of electricity, but also other methods: for example, Brayton cycle (gas turbine) electrical generation, and the direct use of the high temperatures characteristic of HTGR output for process heat in the chemical industry. Such process heat is currently generated by burning fossil fuels, and is a major contributor to the carbon footprint of the chemical and petrochemical industries. The HTGR, based on graphite fuel elements, can produce very high output temperatures; ideally, temperatures of 900 °C or even greater, which has significant energy advantages. Such temperatures are, of course, at the frontiers of materials limitations, at the upper end of the performance envelope of the metallic materials for which robust construction codes exist, and within the realm of ceramic materials, the fabrication and joining of which, on the scale of large energy systems, are at an earlier stage of development. A considerable amount of work was done in the diffusion welding of materials of interest for HTGR service with alloys such as 617 and 800H. The MSR output temperature is also materials limited, and is projected at about 700

  4. Recovery of protactinium from molten fluoride nuclear fuel compositions

    Science.gov (United States)

    Baes, C.F. Jr.; Bamberger, C.; Ross, R.G.

    1973-12-25

    A method is provided for separating protactinium from a molten fluonlde salt composition consisting essentially of at least one alkali and alkaline earth metal fluoride and at least one soluble fluoride of uranium or thorium which comprises oxidizing the protactinium in said composition to the + 5 oxidation state and contacting said composition with an oxide selected from the group consisting of an alkali metal oxide, an alkaline earth oxide, thorium oxide, and uranium oxide, and thereafter isolating the resultant insoluble protactinium oxide product from said composition. (Official Gazette)

  5. Nanoporous surfaces via impact of molten metallic droplets

    Energy Technology Data Exchange (ETDEWEB)

    Qu, Meng [Massachusetts Institute of Technology, Department of Materials Science and Engineering, Cambridge, MA (United States); Colmenares, Jose R.; Valarezo, Alfredo [State University of New York, Stony Brook (United States). Center for Thermal Spray Research; Gouldstone, Andrew [Northeastern University, Department of Mechanical and Industrial Engineering, Boston, MA (United States)

    2009-08-15

    Here we describe a new pathway for the production of nanoporous surfaces, by recourse to molten droplet impact and solidification. The nanopores in this case are frozen in bubbles that nucleate in the melt due to gas supersaturation within 100 nanoseconds of impact. Initial observations and previous analysis are presented, as well as ongoing work to control or pattern porosity via process variation and substrate pre-treatment. This method is presumably not limited in material, and has potential to create large area, functional surfaces. (orig.)

  6. Lithium-ferrate-based cathodes for molten carbonate fuel cells

    Energy Technology Data Exchange (ETDEWEB)

    Lanagan, M.T.; Bloom, I.; Kaun, T.D. [Argonne National Lab., IL (United States)] [and others

    1996-12-31

    Argonne National Laboratory is developing advanced cathodes for pressurized operation of the molten carbonate fuel cell (MCFC) at {approximately}650{degrees}C. To be economically viable for stationary power generation, molten carbonate fuel cells must have lifetimes of more than 25,000 h while exhibiting superior cell performance. In the present technology, lithiated NiO is used as the cathode. Over the lifetime of the cell, however, N{sup 2+} ions tend to transport to the anode, where they are reduced to metallic Ni. With increased CO{sub 2} partial pressure, the transport of Ni increases because of the increased solubility of NiO in the carbonate electrolyte. Although this process is slow in MCFCs operated at 1 atm and a low CO{sub 2} partial pressure (about 0.1 atm), transport of nickel to the anode may be excessive at a higher pressure (e.g., 3 atm) and a high CO{sub 2} partial pressure (e.g., about 0.3 arm). This transport is expected to lead eventually to poor MCFC performance and/or short circuiting. Several alternative cathode compositions have been explored to reduce cathode solubility in the molten salt electrolyte. For example, LiCoO{sub 2} has been studied extensively as a potential cathode material. The LiCoO{sub 2} cathode has a low resistivity, about 10-cm, and can be used as a direct substitute for NiO. Argonne is developing advanced cathodes based on lithium ferrate (LiFeO{sub 2}), which is attractive because of its very low solubility in the molten (Li,K){sub 2}CO{sub 3} electrolyte. Because of its high resistivity (about 3000-cm), however, LiFeO{sub 2} cannot be used as a direct substitute for NiO. Cation substitution is, therefore, necessary to decrease resistivity. We determined the effect of cation substitution on the resistivity and deformation of LiFeO{sub 2}. The substituents were chosen because their respective oxides as well as LiFeO{sub 2} crystallize with the rock-salt structure.

  7. Boron removal from molten silicon using sodium-based slags

    Institute of Scientific and Technical Information of China (English)

    Yin Changhao; Hu Bingfeng; Huang Xinming

    2011-01-01

    Slag refining,as an important option for boron removal to produce solar grade silicon (SOG-Si) from metallurgical grade silicon (MG-Si),has attracted increasing attention.In this paper,Na2CO3-SiO2 systems were chosen as the sodium-based refining slag materials for boron removal from molten silicon.Furthermore,the effect of Al2O3 addition for boron removal was studied in detail,which showed that an appropriate amount of Al2O3 can help retention of the basicity of the slags,hence improving the boron removal rate.

  8. Dynamic modeling of Badaling molten salt tower CSP pilot plant

    Science.gov (United States)

    Yang, Zijiang; Lu, Jiahui; Zhang, Qiangqiang; Li, Zhi; Li, Xin; Wang, Zhifeng

    2017-06-01

    Under the collaboration framework between EDF China R&D Centre and CAS-IEE, a preliminary numerical model of 1MWth molten salt tower solar power demonstration plant in Badaling, Beijing is presented in this paper. All key components in the plant are presented throughout detailed modules in the model according to its design specifications. Control strategies are also implemented to maintain the design system performance at transient scenario. By this model some key design figures of plant has been validated and it will be used to guide experiment set-up and plant commissioning.

  9. Thermolysis of Kansko-Achinsk coal in a molten medium

    Energy Technology Data Exchange (ETDEWEB)

    Uzdenskiy, V.B.; Martynov, Yu.N.; Proskuryakov, V.A.

    1982-01-01

    Thermolysis of Kansko-Achinsk coal is studied in molten mediums of varying nature: metals, such as tin and lead, or salts, such as carbonates of alkaline metals. The effect of temperature, heating rate and nature of the melt on the output and composition of the decomposition products is demonstrated. The use of melts makes it possible to produce 13 to 14 percent resin per unit of coal and gas for use as a reducer or fuel. A melt of salts has an active effect on the decomposition of the organic mass of the coal.

  10. Determination of optimum electrolyte composition for molten carbonate fuel cells

    Energy Technology Data Exchange (ETDEWEB)

    Yuh, C.Y.; Pigeaud, A.

    1987-01-01

    The goal of this program is the development of a molten carbonate fuel cell (MCFC) anode which is more tolerant of sulfur contaminants in the fuel than the current state-of-the-art nickel-based anode structures. This program addresses two different but related aspects of the sulfur contamination problem. The primary aspect is concerned with the development of a sulfur tolerant electrocatalyst for the fuel oxidation reaction. A secondary issue is the development of a sulfur tolerant water-gas-shift reaction catalyst and an investigation of potential steam reforming catalysts which also have some sulfur tolerant capabilities. These two aspects are being addressed as two separate tasks.

  11. Fundamental of Inclusion Removal from Molten Steel by Rising Bubble

    Institute of Scientific and Technical Information of China (English)

    WANG Li-tao; ZHANG Qiao-ying; LI Zheng-bang; XUE Zheng-liang

    2004-01-01

    The mechanism of inclusion removal by attachment to rising bubble was analyzed, and the movement behavior of inclusion, the mechanism of bubbles/inclusion interaction, collision probability and adhesion probability were discussed. A mathematical model of inclusion removal from molten steel by attachment to fine bubble was developed. The results of theoretical analysis and mathematical model showed that the optimum bubble diameter for inclusion removal is 1 to 2 mm. A new method that argon is injected into the shroud from ladle to tundish during continuous casting has been proposed to produce fine bubble. It provides theoretical guides for production of super clean steel.

  12. Diffusion Welding of Alloys for Molten Salt Service - Status Report

    Energy Technology Data Exchange (ETDEWEB)

    Denis Clark; Ronald Mizia

    2012-05-01

    The present work is concerned with heat exchanger development for molten salt service, including the proposed molten salt reactor (MSR), a homogeneous reactor in which the fuel is dissolved in a circulating fluid of molten salt. It is an outgrowth of recent work done under the Next Generation Nuclear Plant (NGNP) program; what the two reactor systems have in common is an inherently safe nuclear plant with a high outlet temperature that is useful for process heat as well as more conventional generation The NGNP program was tasked with investigating the application of a new generation of nuclear power plants to a variety of energy needs. One baseline reactor design for this program is a high temperature, gas-cooled reactor (HTGR), which provides many options for energy use. These might include the conventional Rankine cycle (steam turbine) generation of electricity, but also other methods: for example, Brayton cycle (gas turbine) electrical generation, and the direct use of the high temperatures characteristic of HTGR output for process heat in the chemical industry. Such process heat is currently generated by burning fossil fuels, and is a major contributor to the carbon footprint of the chemical and petrochemical industries. The HTGR, based on graphite fuel elements, can produce very high output temperatures; ideally, temperatures of 900 C or even greater, which has significant energy advantages. Such temperatures are, of course, at the frontiers of materials limitations, at the upper end of the performance envelope of the metallic materials for which robust construction codes exist, and within the realm of ceramic materials, the fabrication and joining of which, on the scale of large energy systems, are at an earlier stage of development. A considerable amount of work was done in the diffusion welding of materials of interest for HTGR service with alloys such as 617 and 800H. The MSR output temperature is also materials limited, and is projected at about 700 C

  13. Steady thermal hydraulic analysis for a molten salt reactor

    Institute of Scientific and Technical Information of China (English)

    ZHANG Dalin; QIU Suizheng; LIU Changliang; SU Guanghui

    2008-01-01

    The Molten Salt Reactor (MSR) can meet the demand of transmutation and breeding. In this study, theoretical calculation of steady thermal hydraulic characteristics of a graphite-moderated channel type MSR is conducted. The DRAGON code is adopted to calculate the axial and radial power factor firstly. The flow and heat transfer model in the fuel salt and graphite are developed on basis of the fundamental mass, momentum and energy equations. The results show the detailed flow distribution in the core, and the temperature profiles of the fuel salt, inner and outer wall in the nine typical elements along the axial flow direction are also obtained.

  14. Measurements of Thermal Conductivity and Thermal Diffusivity of Molten Carbonates

    OpenAIRE

    Wicaksono, Hendro; Zhang, Xing; Fujiwara, Seiji; Fujii, Motoo

    2001-01-01

    The thermal conductivity and thermal diffusivity of molten carbonates (Li_2CO_3/K_2CO_3 and Li_2CO_3/Na_2CO_3) were measured using the transient short-hot-wire method in the temperature range from 530 to 670℃. Two types of probes were examined. One was a platinum short-hot-wire probe coated with alumina (Al_2O_3) thin film to prevent current leakage and corrosion. The other was a bare gold short-hot-wire probe. For the platinum probe, the quality of coating reduces gradually during the measur...

  15. ULTRASONIC SEPARATION OF MICRO-SIZED INCLUSIONSIN MOLTEN METAL

    Institute of Scientific and Technical Information of China (English)

    X.Q. Bai; J.C. He

    2001-01-01

    The coagulation time and position of micro-sized non-metallic inclusions in molten metal during ultrasonic separation process were investigated, and the motion course of micro-sized non-metallic inclusions in an ultrasonic standing wave field was numerically simulated. The results of theoretical analysis and numerical simulation show that the movement of inclusions depends on the balance between the acoustic radiation force, effective buoyancy force and viscous drag force. It is presented that micro-sized inclusions, agglomerated at antinode-planes may be removed further with horizon tal ultrasound.``

  16. Iron-Catalyzed Boron Removal from Molten Silicon in Ammonia

    Science.gov (United States)

    Chen, Zhiyuan; Morita, Kazuki

    2016-12-01

    A high-temperature process of refining metallurgical-grade silicon to solar-grade silicon was developed. In this gas purging treatment, boron impurity in silicon reacts with ammonia and the products are removed as volatiles at high temperature. 1 mass pct metallic iron was added to molten silicon as a catalyst, improving the boron removal ratio from 14 to 80 pct at 1723 K (1450 °C). At 1823 K (1550 °C), this reaction could reduce boron concentration from more than 120 ppmw to activation energy of 329 ± 129 kJ mol-1 was calculated from experimental data.

  17. Corrosion-Resistant Container for Molten-Material Processing

    Science.gov (United States)

    Stern, Theodore G.; McNaul, Eric

    2010-01-01

    In a carbothermal process, gaseous methane is passed over molten regolith, which is heated past its melting point to a temperature in excess of 1,625 C. At this temperature, materials in contact with the molten regolith (or regolith simulant) corrode and lose their structural properties. As a result, fabricating a crucible to hold the molten material and providing a method of contact heating have been problematic. Alternative containment approaches use a large crucible and limit the heat zone of the material being processed, which is inefficient because of volume and mass constraints. Alternative heating approaches use non-contact heating, such as by laser or concentrated solar energy, which can be inefficient in transferring heat and thus require higher power heat sources to accomplish processing. The innovation is a combination of materials, with a substrate material having high structural strength and stiffness and high-temperature capability, and a coating material with a high corrosion resistance and high-temperature capability. The material developed is a molybdenum substrate with an iridium coating. Creating the containment crucible or heater jacket using this material combination requires only that the molybdenum, which is easily processed by conventional methods such as milling, electric discharge machining, or forming and brazing, be fabricated into an appropriate shape, and that the iridium coating be applied to any surfaces that may come in contact with the corrosive molten material. In one engineering application, the molybdenum was fashioned into a container for a heat pipe. Since only the end of the heat pipe is used to heat the regolith, the container has a narrowing end with a nipple in which the heat pipe is snugly fit, and the external area of this nipple, which contacts the regolith to transfer heat into it, is coated with iridium. At the time of this reporting, no single material has been found that can perform the functions of this combination

  18. Energy transformation and flow topology in an elbow draft tube

    Directory of Open Access Journals (Sweden)

    Štefan D.

    2012-06-01

    Full Text Available Paper presents a computational study of energy transformation in two geometrical configurations of Kaplan turbine elbow draft tube. Pressure recovery, hydraulic efficiency and loss coefficient are evaluated for a series of flow rates and swirl numbers corresponding to operating regimes of the turbine. These integral characteristics are then correlated with local flow field properties identified by extraction of topological features. Main focus is to find the reasons for hydraulic efficiency drop of the elbow draft tube.

  19. Investigation of molten pool oscillation during GMAW-P process based on a 3D model

    Science.gov (United States)

    Wang, L. L.; Lu, F. G.; Cui, H. C.; Tang, X. H.

    2014-11-01

    In order to better reveal the oscillation mechanism of the pulsed gas metal arc welding (GMAW-P) process due to an alternately varied welding current, arc plasma and molten pool oscillation were simulated through a self-consistent three-dimensional model. Based on an experimental analysis of the dynamic variation of the arc plasma and molten pool captured by a high-speed camera, the model was validated by comparison of the measured and predicted results. The calculated results showed that arc pressure was the key factor causing the molten pool to oscillate. The variation in arc size and temperature from peak time to base time resulted in a great difference in the heat input and arc pressure acting on the molten pool. The surface deformation of the molten pool due to the varying degrees of arc pressure induced alternate displacement and backflow in the molten metal. The periodic iteration of deeper and shallower surface deformation, drain and backflow of molten metal caused the molten pool to oscillate at a certain frequency. In this condition, the arc pressure at the peak time is more than six times higher than that at the base time, and the maximum surface depression is 1.4 mm and 0.6 mm, respectively, for peak time and base time.

  20. Conformational selection in the molten globule state of the nuclear coactivator binding domain of CBP

    DEFF Research Database (Denmark)

    Kjærgaard, Magnus; Teilum, Kaare; Poulsen, Flemming M

    2010-01-01

    Native molten globules are the most folded kind of intrinsically disordered proteins. Little is known about the mechanism by which native molten globules bind to their cognate ligands to form fully folded complexes. The nuclear coactivator binding domain (NCBD) of CREB binding protein is particul...

  1. Chlorination and Dissolution Process of CeO2 in Molten Salt

    Institute of Scientific and Technical Information of China (English)

    MENG; Zhao-kai; LIN; Ru-shan; CHEN; Hui; ZHANG; Kai; JIA; Yan-hong; WANG; Chang-shui; SONG; Peng; HE; Hui

    2015-01-01

    Molten salt electrolysis is considered as a promising technology in pyrochemical process in recent years.In the pyrochemical process of oxides fuel,dissolution of the oxides is a significant issue for study.Oxides cannot be reduced,as the solubility is small in molten salt.The chlorination of oxides can improve the solubility

  2. Thermodynamic Stability of LiFeO2 in Molten Carbonate Fuel Cell

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    LiFeO2, as one of candidate cathode materials or additive for molten carbonate fuel cell, has been found to be thermodynamically unstable in CO2 atmosphere at 650℃ (the condition of molten carbonate fuel cell) both by computation and experimental confirmation.

  3. Removal of H2S using molten carbonate at high temperature.

    Science.gov (United States)

    Kawase, Makoto; Otaka, Maromu

    2013-12-01

    Gasification is considered to be an effective process for energy conversion from various sources such as coal, biomass, and waste. Cleanup of the hot syngas produced by such a process may improve the thermal efficiency of the overall gasification system. Therefore, the cleanup of hot syngas from biomass gasification using molten carbonate is investigated in bench-scale tests. Molten carbonate acts as an absorbent during desulfurization and dechlorination and as a thermal catalyst for tar cracking. In this study, the performance of molten carbonate for removing H2S was evaluated. The temperature of the molten carbonate was set within the range from 800 to 1000 °C. It is found that the removal of H2S is significantly affected by the concentration of CO2 in the syngas. When only a small percentage of CO2 is present, desulfurization using molten carbonate is inadequate. However, when carbon elements, such as char and tar, are continuously supplied, H2S removal can be maintained at a high level. To confirm the performance of the molten carbonate gas-cleaning system, purified biogas was used as a fuel in power generation tests with a molten carbonate fuel cell (MCFC). The fuel cell is a high-performance sensor for detecting gaseous impurities. When purified gas from a gas-cleaning reactor was continuously supplied to the fuel cell, the cell voltage remained stable. Thus, the molten carbonate gas-cleaning reactor was found to afford good gas-cleaning performance.

  4. Palladium Catalyzed Suzuki Cross-coupling Reaction in Molten Tetra-n-butylammonium Bromide

    Institute of Scientific and Technical Information of China (English)

    ZOU, Yue(邹岳); WANG, Quan-Rui(王全瑞); TAO, Feng-Gang(陶凤岗); DING, Zong-Biao(丁宗彪)

    2004-01-01

    A practical procedure for palladium catalyzed Suzuki cross-coupling reaction of arylboronic acids with aryl halides, including aryl chlorides in molten tetra-n-butylammonium bromide (TBAB) was developed. The reaction exhibits high efficiency and functional group tolerance. The recovery of the catalyst and molten n-Bu4NBr was also investigated.

  5. Topological switching between an alpha-beta parallel protein and a remarkably helical molten globule.

    NARCIS (Netherlands)

    Nabuurs, S.M.; Westphal, A.H.; Toorn, M. aan den; Lindhoud, S.; Mierlo, C.P. van

    2009-01-01

    Partially folded protein species transiently exist during folding of most proteins. Often these species are molten globules, which may be on- or off-pathway to native protein. Molten globules have a substantial amount of secondary structure but lack virtually all the tertiary side-chain packing char

  6. Topological switching between an a-ß parallel protein and a remarkably helical molten globule.

    NARCIS (Netherlands)

    Nabuurs, S.M.; Westphal, A.H.; Toorn, aan den M.; Lindhoud, S.; Mierlo, van C.P.M.

    2009-01-01

    Partially folded protein species transiently exist during folding of most proteins. Often these species are molten globules, which may be on- or off-pathway to native protein. Molten globules have a substantial amount of secondary structure but lack virtually all the tertiary side-chain packing char

  7. Modeling Solute Thermokinetics in LiCI-KCI Molten Salt for Nuclear Waste Separation

    Energy Technology Data Exchange (ETDEWEB)

    Morgan, Dane; Eapen, Jacob

    2013-10-01

    Recovery of actinides is an integral part of a closed nuclear fuel cycle. Pyrometallurgical nuclear fuel recycling processes have been developed in the past for recovering actinides from spent metallic and nitride fuels. The process is essentially to dissolve the spent fuel in a molten salt and then extract just the actinides for reuse in a reactor. Extraction is typically done through electrorefining, which involves electrochemical reduction of the dissolved actinides and plating onto a cathode. Knowledge of a number of basic thermokinetic properties of salts and salt-fuel mixtures is necessary for optimizing present and developing new approaches for pyrometallurgical waste processing. The properties of salt-fuel mixtures are presently being studied, but there are so many solutes and varying concentrations that direct experimental investigation is prohibitively time consuming and expensive (particularly for radioactive elements like Pu). Therefore, there is a need to reduce the number of required experiments through modeling of salt and salt-fuel mixture properties. This project will develop first-principles-based molecular modeling and simulation approaches to predict fundamental thermokinetic properties of dissolved actinides and fission products in molten salts. The focus of the proposed work is on property changes with higher concentrations (up to 5 mol%) of dissolved fuel components, where there is still very limited experimental data. The properties predicted with the modeling will be density, which is used to assess the amount of dissolved material in the salt; diffusion coefficients, which can control rates of material transport during separation; and solute activity, which determines total solubility and reduction potentials used during electrorefining. The work will focus on La, Sr, and U, which are chosen to include the important distinct categories of lanthanides, alkali earths, and actinides, respectively. Studies will be performed using LiCl-KCl salt

  8. An SPH Study of Molten Matte-Slag Dispersion

    Science.gov (United States)

    Natsui, Shungo; Nashimoto, Ryota; Kumagai, Takehiko; Kikuchi, Tatsuya; Suzuki, Ryosuke O.

    2017-02-01

    The transient behaviors of two immiscible liquids, namely, molten matte and molten slag, with a high interfacial tension were investigated using the smoothed particle hydrodynamics model. Numerical simulations were performed using a discrete-element-type method that could track the movement of both the continuous liquid phase and the dispersed one directly. Numerical simulations were also performed for conditions corresponding to different interfacial tension and density values. Further, the predicted topological changes as well as the relationship between the physical properties and the droplet size distribution were investigated. It was found that, with an increase in the interfacial tension, the large droplets formed aggregate quickly with the bulk phase, owing to the buoyancy force. It was also found that the absolute value of the interfacial tension determines the interfacial area, suggesting that it also affects the droplet settling time. As such, we can conclude that the nonlinearly changed interface shape can easily become unstable as a result of only a slight change in the curvature.

  9. Motion and Arrest of a Molten Liquid on Cold Substrates

    Science.gov (United States)

    Tavakoli-Dastjerdi, Faryar

    Spreading of liquid drop on cold solid substrates followed by solidification involves heat transfer, fluid dynamics, and phase change physics. Coupling of these physical phenomena, although present in many industrial applications and nature, renders the physical understanding of the process challenging. Here, the key aspects of molten liquid spreading and solidifying on cold solid substrate are examined experimentally and theoretically. A novel hypothesis of spreading solidifying drops on cold solid substrates is introduced that emphasizes on early stages of the drop solidification at the solid-liquid-gas interface. The derived equations of the drop motion and arrest, stemmed from the development of the presented hypothesis, are in accord with obtained empirical results. The hypothesis is then thoroughly tested with new sets of experiments: i) Drop impact experiments, ii) Inclined plate experiments. In addition, the solidification of static supercooled drops and the initiation mechanism of an intermittent stage (recalescence) are addressed. Also, a peculiar delay-freezing property of hydrophobic surfaces is examined under varying liquid flow rates and substrate temperatures. Moreover, a new phenomenon of cold-induced spreading of water drops on hydrophobic surfaces due to premature condensation followed by thin-film formation at the trijunction is explored and the effect of physical parameters such as relative humidity, the substrate temperature, initial contact angle, surface roughness, and drop volume are investigated. This study will significantly advance the current understanding of dynamic interaction between molten liquid and cold solid substrates.

  10. Pipe Poiseuille flow of viscously anisotropic, partially molten rock

    CERN Document Server

    Allwright, Jane

    2014-01-01

    Laboratory experiments in which synthetic, partially molten rock is subjected to forced deformation provide a context for testing hypotheses about the dynamics and rheology of the mantle. Here our hypothesis is that the aggregate viscosity of partially molten mantle is anisotropic, and that this anisotropy arises from deviatoric stresses in the rock matrix. We formulate a model of pipe Poiseuille flow based on theory by Takei and Holtzman [2009a] and Takei and Katz [2013]. Pipe Poiseuille is a configuration that is accessible to laboratory experimentation but for which there are no published results. We analyse the model system through linearised analysis and numerical simulations. This analysis predicts two modes of melt segregation: migration of melt from the centre of the pipe toward the wall and localisation of melt into high-porosity bands that emerge near the wall, at a low angle to the shear plane. We compare our results to those of Takei and Katz [2013] for plane Poiseuille flow; we also describe a ne...

  11. Sulfide ceramics in molten-salt electrolyte batteries

    Energy Technology Data Exchange (ETDEWEB)

    Kaun, T.D.; Hash, M.C.; Simon, D.R.

    1995-06-01

    Sulfide ceramics are finding application in the manufacture of advanced batteries with molten salt electrolyte. Use of these ceramics as a peripheral seal component has permitted development of bipolar Li/FeS{sub 2} batteries. This bipolar battery has a molten lithium halide electrolyte and operates at 400 to 450C. Initial development and physical properties evaluations indicate the ability to form metal/ceramic bonded seal (13-cm ID) components for use in high-temperature corrosive environments. These sealants are generally CaAl{sub 2}S{sub 4}-based ceramics. Structural ceramics (composites with oxide or nitride fillers), highly wetting sealant formulations, and protective coatings are also being developed. Sulfide ceramics show great promise because of their relatively low melting point, high-temperature viscous flow, chemical stability, high-strength bonding, and tailored coefficients of thermal expansion. Our methodology of generating laminated metal/ceramic pellets (e.g., molybdenum/sulfide ceramic/molybdenum) with which to optimize materials formulation and seal processing is described.

  12. An SPH Study of Molten Matte-Slag Dispersion

    Science.gov (United States)

    Natsui, Shungo; Nashimoto, Ryota; Kumagai, Takehiko; Kikuchi, Tatsuya; Suzuki, Ryosuke O.

    2017-06-01

    The transient behaviors of two immiscible liquids, namely, molten matte and molten slag, with a high interfacial tension were investigated using the smoothed particle hydrodynamics model. Numerical simulations were performed using a discrete-element-type method that could track the movement of both the continuous liquid phase and the dispersed one directly. Numerical simulations were also performed for conditions corresponding to different interfacial tension and density values. Further, the predicted topological changes as well as the relationship between the physical properties and the droplet size distribution were investigated. It was found that, with an increase in the interfacial tension, the large droplets formed aggregate quickly with the bulk phase, owing to the buoyancy force. It was also found that the absolute value of the interfacial tension determines the interfacial area, suggesting that it also affects the droplet settling time. As such, we can conclude that the nonlinearly changed interface shape can easily become unstable as a result of only a slight change in the curvature.

  13. Heat-shrink plastic tubing seals joints in glass tubing

    Science.gov (United States)

    Del Duca, B.; Downey, A.

    1968-01-01

    Small units of standard glass apparatus held together by short lengths of transparent heat-shrinkable polyolefin tubing. The tubing is shrunk over glass O-ring type connectors having O-rings but no lubricant.

  14. A basic study on fluoride-based molten salt electrolysis technology

    Energy Technology Data Exchange (ETDEWEB)

    Hwang, Il Soon [Seoul National University, Seoul (Korea); Kim, Kwang Bum [Yonsei University, Seoul (Korea); Park, Byung Gi [Seoul National University, Seoul (Korea)

    2001-04-01

    The objective of this project is to study on the physicochemical properties of fluoride molten salt, to develop numerical model for simulation of molten salt electrolysis, and to establish experimental technique of fluoride molten salt. Physicochemical data of fluoride molten salt are investigated and summarized. The numerical model, designated as REFIN is developed with diffusion-layer theory and electrochemical reaction kinetics. REFIN is benchmarked with published experimental data. REFIN has a capability to simulate multicomponent electrochemical system at transient conditions. Experimental device is developed to measure electrochemical properties of structural material for fluoride molten salt. Ni electrode is measured with cyclic voltammogram in the conditions of 600 .deg. C LiF-BeF{sub 2} and 700 .deg. C LiF-BeF{sub 2}. 74 refs., 23 figs., 57 tabs. (Author)

  15. Preparation and characterizations of heat storage material combining porous metal with molten salt

    Institute of Scientific and Technical Information of China (English)

    王华; 何方; 戴永年; 胡建杭

    2003-01-01

    A new type of heat storage materials combining high temperature molten salts phases change latent heat thermal storage materials, PCM with porous metals sensible heat thermal storage materials was developed. The process was expressed as following: firstly, it is necessary to heat up the molten salts phases change materials to molten; and then the porous metals are put into the molten bath; after being held for 1-3 h, the composite heat thermal storage materials lumps are taken out of the molten bath and cooled to atmospheric temperature; the last step is to electrodeposit a layer metal coat on the surface of the material lumps. The new type of heat storage material integrates the advantages of both solid sensible heat thermal storage materials and high temperature phases change latent heat thermal storage materials. The metal-base heat storage materials enjoy some favorable characteristics such as higher heat charge-discharge rate, higher heat storage density and better mechanical strength.

  16. Downhole pulse tube refrigerators

    Energy Technology Data Exchange (ETDEWEB)

    Swift, G.; Gardner, D. [Los Alamos National Lab., NM (United States). Condensed Matter and Thermal Physics Group

    1997-12-01

    This report summarizes a preliminary design study to explore the plausibility of using pulse tube refrigeration to cool instruments in a hot down-hole environment. The original motivation was to maintain Dave Reagor`s high-temperature superconducting electronics at 75 K, but the study has evolved to include three target design criteria: cooling at 30 C in a 300 C environment, cooling at 75 K in a 50 C environment, cooling at both 75 K and 30 C in a 250 C environment. These specific temperatures were chosen arbitrarily, as representative of what is possible. The primary goals are low cost, reliability, and small package diameter. Pulse-tube refrigeration is a rapidly growing sub-field of cryogenic refrigeration. The pulse tube refrigerator has recently become the simplest, cheapest, most rugged and reliable low-power cryocooler. The authors expect this technology will be applicable downhole because of the ratio of hot to cold temperatures (in absolute units, such as Kelvin) of interest in deep drilling is comparable to the ratios routinely achieved with cryogenic pulse-tube refrigerators.

  17. The thermal tube

    Energy Technology Data Exchange (ETDEWEB)

    Semena, M.G.

    1980-08-30

    A thermal tube is proposed which contains a layer of dielectric, capillary porous material located on the internal surface of the body. To increase the heat transmitting capability, the layer of capillary porous material is made in the form of a felting, formed by hollow fibers from a non-alkaline, borosilicate glass.

  18. Prawns in Bamboo Tube

    Institute of Scientific and Technical Information of China (English)

    1998-01-01

    Ingredients: 400 grams Jiwei prawns, 25 grams pork shreds, 5 grams sliced garlic. Condiments: 5 grams cooking oil, minced ginger root and scallions, cooking wine, salt, pepper and MSG (optional) Method: 1. Place the Shelled prawns into a bowl and mix with all the condiments. 2. Stuff the prawns into a fresh bamboo tube,

  19. Cladding tube manufacturing technology

    Energy Technology Data Exchange (ETDEWEB)

    Hahn, R. [Kraftwerk Union AG, Mulheim (Germany); Jeong, Y.H.; Baek, B.J.; Kim, K.H.; Kim, S.J.; Choi, B.K.; Kim, J.M. [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

    1999-04-01

    This report gives an overview of the manufacturing routine of PWR cladding tubes. The routine essentially consists of a series of deformation and annealing processes which are necessary to transform the ingot geometry to tube dimensions. By changing shape, microstructure and structure-related properties are altered simultaneously. First, a short overview of the basics of that part of deformation geometry is given which is related to tube reducing operations. Then those processes of the manufacturing routine which change the microstructure are depicted, and the influence of certain process parameters on microstructure and material properties are shown. The influence of the resulting microstructure on material properties is not discussed in detail, since it is described in my previous report 'Alloy Development for High Burnup Cladding.' Because of their paramount importance still up to now, and because manufacturing data and their influence on properties for other alloys are not so well established or published, the descriptions are mostly related to Zry4 tube manufacturing, and are only in short for other alloys. (author). 9 refs., 46 figs.

  20. Misdirected Minitracheostomy Tube

    Science.gov (United States)

    Singh, Ajmer; Nanda, Chinmaya; Mehta, Yatin

    2017-01-01

    We report a patient who after an uneventful coronary artery bypass graft surgery and left ventricular aneurysmorrhaphy developed intracerebral hemorrhage and subsequently required minitracheostomy. Chest X-ray showed misdirected minitracheostomy tube facing upward toward the laryngeal opening which was repositioned using bronchoscope. PMID:28074805

  1. Misdirected minitracheostomy tube

    Directory of Open Access Journals (Sweden)

    Ajmer Singh

    2017-01-01

    Full Text Available We report a patient who after an uneventful coronary artery bypass graft surgery and left ventricular aneurysmorrhaphy developed intracerebral hemorrhage and subsequently required minitracheostomy. Chest X-ray showed misdirected minitracheostomy tube facing upward toward the laryngeal opening which was repositioned using bronchoscope.

  2. Reductive smelting of spent lead-acid battery colloid sludge in a molten Na2CO3 salt

    Institute of Scientific and Technical Information of China (English)

    Yu-jie Hu; Chao-bo Tang; Mo-tang Tang; Yong-ming Chen

    2015-01-01

    Lead extraction from spent lead–acid battery paste in a molten Na2CO3 salt containing ZnO as a sulfur-fixing agent was studied. Some influencing factors, including smelting temperature, reaction time, ZnO and salt dosages, were investigated in detail using single-factor experiments. The optimum conditions were determined as follows:T = 880°C;t = 60 min; Na2CO3/paste mass ratio = 2.8:1; and the ZnO dosage is equal to the stoichiometric requirement. Under the optimum conditions, the direct recovery rate of lead reached 98.14%. The re-sults suggested that increases in temperature and salt dosage improved the direct recovery rate of lead. XRD results and thermodynamic cal-culations indicated that the reaction approaches of lead and sulfur were PbSO4→Pb and PbSO4→ZnS, respectively. Sulfur was fixed in the form of ZnS, whereas the molten salt did not react with other components, serving only as a reaction medium.

  3. Restore condition of Incore thimble tubes in guide tubes

    Energy Technology Data Exchange (ETDEWEB)

    Solanas, A.; Izquierdo, J.

    2014-07-01

    Aging of Nuclear Power Plant and succession of outages lead to wear and twist of the thimbles tubes but also to the fooling of Incore guide tubes. These can create friction and a high strength must be used for thimble tubes withdrawal. (Author)

  4. Eustachian tube function in children after insertion of ventilation tubes.

    NARCIS (Netherlands)

    Heerbeek, N. van; Ingels, K.J.A.O.; Snik, A.F.M.; Zielhuis, G.A.

    2001-01-01

    This study was performed to assess the effect of the insertion of ventilation tubes and the subsequent aeration of the middle ear on eustachian tube (ET) function in children. Manometric ET function tests were performed repeatedly for 3 months after the placement of ventilation tubes in 83 children

  5. Nuclear Hybrid Energy System: Molten Salt Energy Storage (Summer Report 2013)

    Energy Technology Data Exchange (ETDEWEB)

    Sabharwall, Piyush [Idaho National Lab. (INL), Idaho Falls, ID (United States); mckellar, Michael George [Idaho National Lab. (INL), Idaho Falls, ID (United States); Yoon, Su-Jong [Idaho National Lab. (INL), Idaho Falls, ID (United States)

    2013-11-01

    Effective energy use is a main focus and concern in the world today because of the growing demand for energy. The nuclear hybrid energy system (NHES) is a valuable technical concept that can potentially diversify and leverage existing energy technologies. This report considers a particular NHES design that combines multiple energy systems including a nuclear reactor, energy storage system (ESS), variable renewable generator (VRG), and additional process heat applications. Energy storage is an essential component of this particular NHES because its design allows the system to produce peak power while the nuclear reactor operates at constant power output. Many energy storage options are available, but this study mainly focuses on a molten salt ESS. The primary purpose of the molten salt ESS is to enable the nuclear reactor to be a purely constant heat source by acting as a heat storage component for the reactor during times of low demand, and providing additional capacity for thermo-electric power generation during times of peak electricity demand. This report will describe the rationale behind using a molten salt ESS and identify an efficient molten salt ESS configuration that may be used in load following power applications. Several criteria are considered for effective energy storage and are used to identify the most effective ESS within the NHES. Different types of energy storage are briefly described with their advantages and disadvantages. The general analysis to determine the most efficient molten salt ESS involves two parts: thermodynamic, in which energetic and exergetic efficiencies are considered; and economic. Within the molten salt ESS, the two-part analysis covers three major system elements: molten salt ESS designs (two tank direct and thermocline), the molten salt choice, and the different power cycles coupled with the molten salt ESS. Analysis models are formulated and analyzed to determine the most effective ESS. The results show that the most

  6. Study of thorium-uranium based molten salt blanket in a fusion-fission hybrid reactor

    Energy Technology Data Exchange (ETDEWEB)

    Zhao Jing, E-mail: zhao_jing@mail.tsinghua.edu.cn [INET, Tsinghua University, Beijing 100084 (China); Yang Yongwei; Zhou Zhiwei [INET, Tsinghua University, Beijing 100084 (China)

    2012-08-15

    Highlights: Black-Right-Pointing-Pointer A molten salt blanket has been designed for the fusion-fission hybrid reactor. Black-Right-Pointing-Pointer The use of Thorium in the molten salt fuels has been studied. Black-Right-Pointing-Pointer The molten salt was consisted of F-Li-Be and with the thickness of 40 cm. Black-Right-Pointing-Pointer The concentration of {sup 6}Li was chosen to be the natural enrichment ratio. Black-Right-Pointing-Pointer The result shows that TBR is greater than 1, M is about 15-16. - Abstract: Not only solid fuels, but also liquid fuels can be used for the fusion-fission symbiotic reactor blanket. The operational record of the molten salt reactor with F-Li-Be was very successful, so the F-Li-Be blanket was chosen for research. The molten salt has several features which are suited for the fusion-fission applications. The fuel material uranium and thorium were dissolved in the F-Li-Be molten salt. A combined program, COUPLE, was used for neutronics analysis of the molten salt blanket. Several cases have been calculated and compared. Not only the influence of the different fuels have been studied, but also the thickness of the molten salt, and the concentration of the {sup 6}Li in the molten salt. Preliminary studies indicate that when thorium-uranium-plutonium fuels were added into a F-Li-Be molten salt blanket and with a component of 71% LiF-2% BeF{sub 2}-13.5% ThF{sub 4}-8.5% UF{sub 4}-5% PuF{sub 3}, and also with the molten salt thickness of 40 cm and natural concentration of {sup 6}Li, the appropriate blanket energy multiplication factor and TBR can be obtained. The result shows that thorium-uranium molten salt can be used in the blanket of a fusion-fission symbiotic reactor. The research on the molten salt blanket must be valuable for the design of fusion-fission symbiotic reactor.

  7. Enteral Tube Feeding and Pneumonia

    Science.gov (United States)

    Gray, David Sheridan; Kimmel, David

    2006-01-01

    To determine the effects of enteral tube feeding on the incidence of pneumonia, we performed a retrospective review of all clients at our institution who had gastrostomy or jejunostomy tubes placed over a 10-year period. Ninety-three subjects had a history of pneumonia before feeding tube insertion. Eighty had gastrostomy and 13, jejunostomy…

  8. REAKTOR INNOVATIVE MOLTEN SALT (IMSR DENGAN SISTEM KESELAMATAN PASIF MENYELURUH

    Directory of Open Access Journals (Sweden)

    Andang Widiharto

    2015-04-01

    Full Text Available Pengembangan Teknologi Reaktor Nuklir pada masa mendatang mengarah pada peningkatan aspek keselamatan, peningkatan pendayagunaan bahan bakar, reduksi limbah radioaktif, ketahanan terhadap proliferasi bahan-bakar nuklir dan peningkatan aspek ekonomi. reaktor Innovative Molten Salt (IMSR adalah reaktor nuklir yang menggunakan bahan bakar cair berupa garam lebur fluoride (7LiF-ThF4-UF4-MaFx. Reaktor IMSR didesain sebagai reaktor pembiak termal, yaitu membiakkan U-233 dari Th-232. Hal ini untuk menjawab permasalahan sustainabilitas ketersedian sumber daya bahan bakar nuklir dan reduksi limbah radioaktif. Dalam aspek keselamatan, desain reaktor IMSR memiliki sifat inherent safe, yaitu koefisien umpan balik daya yang negatif serta memiliki fitur-fitur keselamatan pasif. Fitur-fitur keselamatan pasif terdiri dari sistem shutdown pasif, sistem pendinginan pasif pasca shutdown serta sistem pendinginan pasif untuk produk fisi. Kecelakaan yang berpotensi terjadi pada IMSR, yaitu kecelakaan kehilangan aliran bahan bakar, kecelakaan kehilangan aliran pendingin, kecelakaan kehilangan kemampuan pengambilan kalor serta kecelakaan kerusakan integritas sistem reaktor, dapat ditangani sepenuhnya secara pasif hingga mencapai kondisi shutdown selamat. Kata kunci: keselamatan pasif, inherent safe, IMSR   The next Nuclear Reactor Technology developments are directed to the increasing of the aspects of safety, fuel utility, radioactive waste reduction, proliferation retention and economy. Innovative Molten Salt Reactor (IMSR is a nuclear reactor design that uses fluoride molten salt (7LiF-ThF4-UF4-MaFx. IMSR is designed as a thermal breeder reactor, i.e. to produce U-233 from Th-232. This is the answer of natural nuclear fuel sustainability and radioactive waste problems. In term of safety aspect, IMSR design has inherent safe characteristics, i.e. negative power feedback coefficient, and passive safety features. The passive safety features are passive shutdown

  9. Molten Chloride Salts for Heat Transfer in Nuclear Systems

    Science.gov (United States)

    Ambrosek, James Wallace

    2011-12-01

    A forced convection loop was designed and constructed to examine the thermal-hydraulic performance of molten KCl-MgCl2 (68-32 at %) salt for use in nuclear co-generation facilities. As part of this research, methods for prediction of the thermo-physical properties of salt mixtures for selection of the coolant salt were studied. In addition, corrosion studies of 10 different alloys were exposed to the KCl-MgCl2 to determine a suitable construction material for the loop. Using experimental data found in literature for unary and binary salt systems, models were found, or developed to extrapolate the available experimental data to unstudied salt systems. These property models were then used to investigate the thermo-physical properties of the LINO3-NaNO3-KNO 3-Ca(NO3), system used in solar energy applications. Using these models, the density, viscosity, adiabatic compressibility, thermal conductivity, heat capacity, and melting temperatures of higher order systems can be approximated. These models may be applied to other molten salt systems. Coupons of 10 different alloys were exposed to the chloride salt for 100 hours at 850°C was undertaken to help determine with which alloy to construct the loop. Of the alloys exposed, Haynes 230 had the least amount of weight loss per area. Nickel and Hastelloy N performed best based on maximum depth of attack. Inconel 625 and 718 had a nearly uniform depletion of Cr from the surface of the sample. All other alloys tested had depletion of Cr along the grain boundaries. The Nb in Inconel 625 and 718 changed the way the Cr is depleted in these alloys. Grain-boundary engineering (GBE) of Incoloy 800H improved the corrosion resistance (weight loss and maximum depth of attack) by nearly 50% as compared to the as-received Incoloy 800H sample. A high temperature pump, thermal flow meter, and pressure differential device was designed, constructed and tested for use in the loop, The heat transfer of the molten chloride salt was found to

  10. ANALISIS TRANSIEN PADA PASSIVE COMPACT MOLTEN SALT REACTOR (PCMSR

    Directory of Open Access Journals (Sweden)

    M. Makrus Imron

    2015-04-01

    Full Text Available Penggunaan bahan bakar cair berupa garam LiF-BeF2-ThF4-UF4 pada Passive Compact Molten Salt Reactor (PCMSR meyebabkan pengendalian daya pada PCMSR dapat dilakukan dengan mengendalikan laju aliran bahan bakar dan pendingin. Sedangkan dari sistem keselamatan, penggunaan bahan bakar cair menjadikan PCMSR memiliki karakter keselamatan melekat (inherent safety yang baik. Pada penelitian ini telah dilakukan analisis transien PCMSR pada tiga kondisi, yaitu: ketika terjadi perubahan laju aliran bahan bakar, ketika terjadi perubahan laju aliran pendingin dan ketika terdapat kegagalan pada sistem pelepasan panas (loss of heat sink. Penelitian dilakukan dengan memodelkan reaktor pada kondisi tunak menggunakan paket program. Standart Reactor Analysis Code (SRAC. Selanjutnya dari keluaran paket program SRAC diperoleh data data yang meliputi fluks netron,konstanta grup, kontanta peluran prekusor netron, fraksi netron kasip untuk perhitungan transien. Penelitian ini menunjukkan bahwa penurunan laju aliran bahan bakar sebesar 50 % dari laju bahan bakar sebelumnya, menyebabkan daya pada PCMSR turun menjadi 78 % dari daya sebelumnya. Dan penurunan laju aliran pendingin sebesar 50 % dari laju pendingin sebelumnya, menyebabkan daya pada PCMSR turun menjadi 63 % dari daya sebelumnya. Sedangkan pada saat terjadi loss of heat sink daya PCMSR menunjukkan penurunan. Kata kunci: PCMSR, transien, daya, laju aliran.   The use of liquid fuels in the form of molten salts LiF-BeF2-ThF4-UF4 in Passive Compact Molten Salt Reactor (PCMSR makes power control at PCMSR can be done by controlling the flow rate of fuel and coolant. In addition, from safety systems aspect, the use of liquid fuels makes PCMSR has good inherent safety characteristics. In this study transient analysis has been carried out on three conditions of PCMSR, namely when the fuel flow rate is changing, when the coolant flow rate is changing and when there is loss of heat sink condition. This research is

  11. Recent advances in the molten salt destruction of energetic materials

    Energy Technology Data Exchange (ETDEWEB)

    Pruneda, C. O., LLNL

    1996-09-01

    We have demonstrated the use of the Molten Salt Destruction (MSD) Process for destroying explosives, liquid gun propellant, and explosives-contaminated materials on a 1.5 kg of explosive/hr bench- scale unit (1, 2, 3, 4, 5). In our recently constructed 5 kg/hr pilot- scale unit we have also demonstrated the destruction of a liquid gun propellant and simulated wastes containing HMX (octogen). MSD converts the organic constituents of the waste into non-hazardous substances such as carbon dioxide, nitrogen, and water. Any inorganic constituents of the waste, such as metallic particles, are retained in the molten salt. The destruction of energetic materials waste is accomplished by introducing it, together with air, into a vessel containing molten salt (a eutectic mixture of sodium, potassium, and lithium carbonates). The following pure explosives have been destroyed in our bench-scale experimental unit located at Lawrence Livermore National Laboratory`s (LLNL) High Explosives Applications Facility (HEAF): ammonium picrate, HMX, K- 6 (keto-RDX), NQ, NTO, PETN, RDX, TATB, and TNT. In addition, the following compositions were also destroyed: Comp B, LX- IO, LX- 1 6, LX- 17, PBX-9404, and XM46 (liquid gun propellant). In this 1.5 kg/hr bench-scale unit, the fractions of carbon converted to CO and of chemically bound nitrogen converted to NO{sub x} were found to be well below 1%. In addition to destroying explosive powders and compositions we have also destroyed materials that are typical of residues which result from explosives operations. These include shavings from machined pressed parts of plastic-bonded explosives and sump waste containing both explosives and non-explosive debris. Based on the process data obtained on the bench-scale unit we designed and constructed a next-generation 5 kg/hr pilot-scale unit, incorporating LLNL`s advanced chimney design. The pilot unit has completed process implementation operations and explosives safety reviews. To date, in this

  12. Neural tube defects

    Directory of Open Access Journals (Sweden)

    M.E. Marshall

    1981-09-01

    Full Text Available Neural tube defects refer to any defect in the morphogenesis of the neural tube, the most common types being spina bifida and anencephaly. Spina bifida has been recognised in skeletons found in north-eastern Morocco and estimated to have an age of almost 12 000 years. It was also known to the ancient Greek and Arabian physicians who thought that the bony defect was due to the tumour. The term spina bifida was first used by Professor Nicolai Tulp of Amsterdam in 1652. Many other terms have been used to describe this defect, but spina bifida remains the most useful general term, as it describes the separation of the vertebral elements in the midline.

  13. Vortex tube optimization theory

    Energy Technology Data Exchange (ETDEWEB)

    Lewins, Jeffery [Cambridge Univ., Magdalene Coll., Cambridge (United Kingdom); Bejan, Adrian [Duke Univ., Dept. of Mechanical Engineering and Materials Science, Durham, NC (United States)

    1999-11-01

    The Ranque-Hilsch vortex tube splits a single high pressure stream of gas into cold and warm streams. Simple models for the vortex tube combined with regenerative precooling are given from which an optimisation can be undertaken. Two such optimisations are needed: the first shows that at any given cut or fraction of the cold stream, the best refrigerative load, allowing for the temperature lift, is nearly half the maximum loading that would result in no lift. The second optimisation shows that the optimum cut is an equal division of the vortex streams between hot and cold. Bounds are obtainable within this theory for the performance of the system for a given gas and pressure ratio. (Author)

  14. Centrifugal separation for miscible solutions: Fundamentals and applications to separation of molten salt nuclear material

    Science.gov (United States)

    Li, Ning; Camassa, Roberto; Ecke, Robert E.; Venneri, Francesco

    1995-09-01

    We report on the physical separation of dilute solutions using centrifugal techniques. We use numerical simulations of the diffusion and sedimentation dynamics of centrifugation to model the approach to an equilibrium concentration profile. We verify experimentally the equilibrium profiles for aqueous solutions of different salts under rotation at 25000 rpm corresponding to centrifugal accelerations of about 57,000 g and 75,000 g in two different commercial centrifuges. These measurements provide ratios of sedimentation and diffusion coefficients. We show experimental results for the dynamics of separation that confirm the predictions of the theoretical model. We also measure the mass diffusion coefficient for several solutions. Although the relaxation to equilibrium is long, we have determined a method for efficiently extracting enriched components from a ternary mixture based on fast dynamics at early times. These dynamics are modeled in numerical simulations with realistic fluid parameters. Based on these studies we show that a multistage centrifugal separation process could provide efficient physical separation of actinides and fission products from a molten-salt solution in proposed transmutation/energy-production systems. We consider technical issues in the design of such a separation system.

  15. A wandering tube.

    Science.gov (United States)

    Dubin, Ina; Gelber, Moshe; Schattner, Ami

    2016-12-05

    The predominant causes of acute mechanical small bowel obstruction in geriatric patients are adhesions and hernias, which is not much different than in other adult age groups. Unusual etiologies may be encountered, such as volvulus or gallstone ileus, but a displaced feeding gastrostomy tube is a distinctly rare cause of intestinal obstruction which needs to be considered by emergency physicians as it may be increasingly encountered.

  16. Primary fallopian tube carcinoma

    Directory of Open Access Journals (Sweden)

    Mladenović-Segedi Ljiljana

    2009-01-01

    Full Text Available Introduction. Primary fallopian tube carcinoma is extremely rare, making 0.3-1.6% of all female genital tract malignancies. Although the etymology of this tumor is unknown, it is suggested to be associated with chronic tubal inflammation, infertility, tuberculous salpingitis and tubal endometriosis. High parity is considered to be protective. Cytogenetic studies show the disease to be associated with over expression of p53, HER2/neu and c-myb. There is also some evidence that BRCA1 and BRCA2 mutations have a role in umorogeneis. Clinical features. The most prevailing symptoms with fallopian tube carcinoma are abdominal pain, abnormal vaginal discharge/bleeding and the most common finding is an adnexal mass. In many patients, fallopian tube carcinoma is asymptomatic. Diagnosis. Due to its rarity, preoperative diagnosis of primary fallopian tube carcinoma is rarely made. It is usually misdiagnosed as ovarian carcinoma, tuboovarian abscess or ectopic pregnancy. Sonographic features of the tumor are non-specific and include the presence of a fluid-filled adnexal structure with a significant solid component, a sausage-shaped mass, a cystic mass with papillary projections within, a cystic mass with cog wheel appearance and an ovoid-shaped structure containing an incomplete separation and a highly vascular solid nodule. More than 80% of patients have elevated pretreatment serum CA-125 levels, which is useful in follow-up after the definite treatment. Treatment. The treatment approach is similar to that of ovarian carcinoma, and includes total abdominal hysterectomy and bilateral salpingo-oophorectomy. Staging is followed with chemotherapy.

  17. Molten salt parabolic trough system with synthetic oil preheating

    Science.gov (United States)

    Yuasa, Minoru; Hino, Koichi

    2017-06-01

    Molten salt parabolic trough system (MSPT), which can heat the heat transfer fluid (HTF) to 550 °C has a better performance than a synthetic oil parabolic trough system (SOPT), which can heat the HTF to 400 °C or less. The utilization of HTF at higher temperature in the parabolic trough system is able to realize the design of a smaller size of storage tank and higher heat to electricity conversion efficiency. However, with MSPT there is a great amount of heat loss at night so it is necessary to circulate the HTF at a high temperature of about 290 °C in order to prevent solidification. A new MSPT concept with SOPT preheating (MSSOPT) has been developed to reduce the heat loss at night. In this paper, the MSSOPT system, its performance by steady state analysis and annual performance analysis are introduced.

  18. Controlled Molten Metal Droplet Deposition for Net-Form Manufacturing

    Science.gov (United States)

    Orme, Melissa; Michaelis, Matthew; Smith, Robert

    2001-11-01

    Molten metal droplets generated from capillary stream breakup are employed as the deposition element in a droplet-based net-form manufacturing technique that is under development at UCI. The metallic droplets are electrostatically charged at the time of generation and are subsequently deflected onto a substrate by passing them through an electric field. As a showcase to this new technique, we have employed various combinations of electrostatic charging and substrate motion in order to net-form manufacture rectangular components with both thick (2.8 mm) and thin (0.6 mm) walls, tubular components with clover cross-sections, and intriguing metallic braids up to 3.0 meters in length.

  19. Molten Salt Fuel Cycle Requirements for ADTT Applications

    Energy Technology Data Exchange (ETDEWEB)

    Williams, D. F. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Del Cul, G. D. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Toth, L. M. [Commodore Advanced Sciences, Inc., Oak Ridge, TN (United States)

    1999-06-07

    The operation of an ADT system with the associated nuclear reactions has a profound effect upon the chemistry of the fuel - especially with regards to container compatibility and the chemical separations that may be required. The container can be protected by maintaining the redox chemistry within a relatively narrow, non-corrosive window. Neutron economy as well as other factors require a sophisticated regime of fission product separations. Neither of these control requirements has been demonstrated on the scale or degree of sophistication necessary to support an ADT device. We review the present situation with respect to fluoride salts, and focus on the critical issues in these areas which must be addressed. One requirement for advancement in this area - a supply of suitable materials - will soon be fulfilled by the remediation of ORNL's Molten Salt Reactor Experiment, and the removal of a total of 11,000 kg of enriched (Li-7 > 99.9%) coolant, flush, and fuel salts.

  20. Al slurry coatings for molten carbonate fuel cells separator plates

    Energy Technology Data Exchange (ETDEWEB)

    Agueero, A.; Garcia, M.C.; Muelas, R.; Sanchez, A. [Instituto Nacional de Tecnica Aerospacial, Madrid (Spain); Perez, F.J.; Duday, D.; Hierro, M.P.; Gomez, C. [Universidad Complutense de Madrid (Spain). Dept. de Ciencia de los Materiales

    2001-07-01

    The corrosion behaviour of Al slurry coated AISI 310 stainless steel, with and without diffusion heat treatment, was investigated as a wet seal material for molten carbonate fuel cell (MCFC) at 650 C. The results were compared with IVD Al coated AISI 310. Characterization of the samples before and after exposure to the eutectic 62 mol% Li{sub 2}CO{sub 3}-38 mol% K{sub 2}CO{sub 3} mixture at 650 C for 1000 h by SEM-EDS and XRD was carried out. The presence of LiAlO{sub 2} on the coated samples was confirmed by XRD. The slurry Al-coated stainless steels performed at least as well as the IVD Al coating. (orig.)

  1. Electrodeposition of aluminum on aluminum surface from molten salt

    Institute of Scientific and Technical Information of China (English)

    Wenmao HUANG; Xiangyu XIA; Bin LIU; Yu LIU; Haowei WANG; Naiheng MA

    2011-01-01

    The surface morphology,microstructure and composition of the aluminum coating of the electrodeposition plates in AlC13-NaC1-KC1 molten salt with a mass ratio of 8:1:1 were investigated by SEM and EDS.The binding force was measured by splat-cooling method and bending method.The results indicate that the coatings with average thicknesses of 12 and 9 μm for both plates treated by simple grinding and phosphating are compacted,continuous and well adhered respectively. Tetramethylammonium chloride (TMAC) can effectively prevent the growth of dendritic crystal,and the anode activation may improve the adhesion of the coating. Binding force analysis shows that both aluminum coatings are strongly adhered to the substrates.

  2. Multimedia Information Extraction

    CERN Document Server

    Maybury, Mark T

    2012-01-01

    The advent of increasingly large consumer collections of audio (e.g., iTunes), imagery (e.g., Flickr), and video (e.g., YouTube) is driving a need not only for multimedia retrieval but also information extraction from and across media. Furthermore, industrial and government collections fuel requirements for stock media access, media preservation, broadcast news retrieval, identity management, and video surveillance.  While significant advances have been made in language processing for information extraction from unstructured multilingual text and extraction of objects from imagery and vid

  3. Traveling-Wave Tubes

    Science.gov (United States)

    Kory, Carol L.

    1998-01-01

    The traveling-wave tube (TWT) is a vacuum device invented in the early 1940's used for amplification at microwave frequencies. Amplification is attained by surrendering kinetic energy from an electron beam to a radio frequency (RF) electromagnetic wave. The demand for vacuum devices has been decreased largely by the advent of solid-state devices. However, although solid state devices have replaced vacuum devices in many areas, there are still many applications such as radar, electronic countermeasures and satellite communications, that require operating characteristics such as high power (Watts to Megawatts), high frequency (below 1 GHz to over 100 GHz) and large bandwidth that only vacuum devices can provide. Vacuum devices are also deemed irreplaceable in the music industry where musicians treasure their tube-based amplifiers claiming that the solid-state and digital counterparts could never provide the same "warmth" (3). The term traveling-wave tube includes both fast-wave and slow-wave devices. This article will concentrate on slow-wave devices as the vast majority of TWTs in operation fall into this category.

  4. Molten Salt Test Loop (MSTL) system customer interface document.

    Energy Technology Data Exchange (ETDEWEB)

    Gill, David Dennis; Kolb, William J.; Briggs, Ronald D.

    2013-09-01

    The National Solar Thermal Test Facility at Sandia National Laboratories has a unique test capability called the Molten Salt Test Loop (MSTL) system. MSTL is a test capability that allows customers and researchers to test components in flowing, molten nitrate salt. The components tested can range from materials samples, to individual components such as flex hoses, ball joints, and valves, up to full solar collecting systems such as central receiver panels, parabolic troughs, or linear Fresnel systems. MSTL provides realistic conditions similar to a portion of a concentrating solar power facility. The facility currently uses 60/40 nitrate %E2%80%9Csolar salt%E2%80%9D and can circulate the salt at pressure up to 40 bar (600psi), temperature to 585%C2%B0C, and flow rate of 44-50kg/s(400-600GPM) depending on temperature. The purpose of this document is to provide a basis for customers to evaluate the applicability to their testing needs, and to provide an outline of expectations for conducting testing on MSTL. The document can serve as the basis for testing agreements including Work for Others (WFO) and Cooperative Research and Development Agreements (CRADA). While this document provides the basis for these agreements and describes some of the requirements for testing using MSTL and on the site at Sandia, the document is not sufficient by itself as a test agreement. The document, however, does provide customers with a uniform set of information to begin the test planning process.

  5. Molten carbonate fuel cell technology improvement. Final report

    Energy Technology Data Exchange (ETDEWEB)

    1991-06-01

    This report summarizes the work performed under Department of Energy Contract DEAC21-87MC23270, ``Molten Carbonate Fuel Cell Technology Improvement.`` This work was conducted over a three year period and consisted of three major efforts. The first major effort was the power plant system study which reviewed the competitive requirements for a coal gasifier/molten carbonate fuel cell power plant, produced a conceptual design of a CG/MCFC, and defined the technology development requirements. This effort is discussed in Section 1 of the report. The second major effort involved the design and development of a new MCFC cell configuration which reduced the material content of the cell to a level competitive with competing power plants, simplified the cell configuration to make the components more manufacturable and adaptable to continuous low cost processing techniques, and introduced new-low-pressure drop flow fields for both reactant gases. The new flow fields permitted the incorporation of recirculation systems in both reactant gas systems, permitting simplified cooling techniques and the ability to operate on both natural gas and a wide variety of gasifier fuels. This cell technology improvement is discussed in Section 2. The third major effort involved the scaleup of the new cell configuration to the full-area, 8-sq-ft size and resulted in components used for a 25-kW, 20-cell stack verification test. The verification test was completed with a run of 2200 hours, exceeding the goal of 2000 hours and verifying the new cell design. TWs test, in turn, provided the confidence to proceed to a 100-kW demonstration which is the goal of the subsequent DOE program. The scaleup and stack verification tests are discussed in Sections 3, 4, 5, and 6 of this report.

  6. On purpose simulation model for molten salt CSP parabolic trough

    Science.gov (United States)

    Caranese, Carlo; Matino, Francesca; Maccari, Augusto

    2017-06-01

    The utilization of computer codes and simulation software is one of the fundamental aspects for the development of any kind of technology and, in particular, in CSP sector for researchers, energy institutions, EPC and others stakeholders. In that extent, several models for the simulation of CSP plant have been developed with different main objectives (dynamic simulation, productivity analysis, techno economic optimization, etc.), each of which has shown its own validity and suitability. Some of those models have been designed to study several plant configurations taking into account different CSP plant technologies (Parabolic trough, Linear Fresnel, Solar Tower or Dish) and different settings for the heat transfer fluid, the thermal storage systems and for the overall plant operating logic. Due to a lack of direct experience of Molten Salt Parabolic Trough (MSPT) commercial plant operation, most of the simulation tools do not foresee a suitable management of the thermal energy storage logic and of the solar field freeze protection system, but follow standard schemes. ASSALT, Ase Software for SALT csp plants, has been developed to improve MSPT plant's simulations, by exploiting the most correct operational strategies in order to provide more accurate technical and economical results. In particular, ASSALT applies MSPT specific control logics for the electric energy production and delivery strategy as well as the operation modes of the Solar Field in off-normal sunshine condition. With this approach, the estimated plant efficiency is increased and the electricity consumptions required for the plant operation and management is drastically reduced. Here we present a first comparative study on a real case 55 MWe Molten Salt Parabolic Trough CSP plant placed in the Tibetan highlands, using ASSALT and SAM (System Advisor Model), which is a commercially available simulation tool.

  7. Research of Real-time Grabbing Yarn Tube System Based on Machine Vision

    Directory of Open Access Journals (Sweden)

    Cui Shigang

    2015-01-01

    Full Text Available The current yarn tube manipulator just finishes yarn tube grabbing work according to the fixed coordinates. In the actual production process, equipment problems or human factors which make the spindles not on fixed coordinates cause the damage of the manipulator. Real-time grabbing yarn tube system with visual sensing has been designed and a extraction algorithm of spindles coordinates based on a mixed image morphology and Hough transform algorithm has been proposed. Through the combination of the yarn tube image characteristics which are extracted by the algorithm and the visual measurement model which is established by pinhole imaging principle, the mapping relation of yarn tube image coordinates and world coordinates has been gained to get the location information of yarn tube in real time. Results show that the proposed method could make the robot complete the grabbing job precisely and efficiently, under which the system meet the requirement of spinning and dyeing production line.

  8. Reliability of steam generator tubing

    Energy Technology Data Exchange (ETDEWEB)

    Kadokami, E. [Mitsubishi Heavy Industries Ltd., Hyogo-ku (Japan)

    1997-02-01

    The author presents results on studies made of the reliability of steam generator (SG) tubing. The basis for this work is that in Japan the issue of defects in SG tubing is addressed by the approach that any detected defect should be repaired, either by plugging the tube or sleeving it. However, this leaves open the issue that there is a detection limit in practice, and what is the effect of nondetectable cracks on the performance of tubing. These studies were commissioned to look at the safety issues involved in degraded SG tubing. The program has looked at a number of different issues. First was an assessment of the penetration and opening behavior of tube flaws due to internal pressure in the tubing. They have studied: penetration behavior of the tube flaws; primary water leakage from through-wall flaws; opening behavior of through-wall flaws. In addition they have looked at the question of the reliability of tubing with flaws during normal plant operation. Also there have been studies done on the consequences of tube rupture accidents on the integrity of neighboring tubes.

  9. Automated Identification and Reconstruction of YouTube Video Access

    Directory of Open Access Journals (Sweden)

    Jonathan Patterson

    2012-06-01

    Full Text Available YouTube is one of the most popular video-sharing websites on the Internet, allowing users to upload, view and share videos with other users all over the world. YouTube contains many different types of videos, from homemade sketches to instructional and educational tutorials, and therefore attracts a wide variety of users with different interests. The majority of YouTube visits are perfectly innocent, but there may be circumstances where YouTube video access is related to a digital investigation, e.g. viewing instructional videos on how to perform potentially unlawful actions or how to make unlawful articles.When a user accesses a YouTube video through their browser, certain digital artefacts relating to that video access may be left on their system in a number of different locations. However, there has been very little research published in the area of YouTube video artefacts.The paper discusses the identification of some of the artefacts that are left by the Internet Explorer web browser on a Windows system after accessing a YouTube video. The information that can be recovered from these artefacts can include the video ID, the video name and possibly a cached copy of the video itself. In addition to identifying the artefacts that are left, the paper also investigates how these artefacts can be brought together and analysed to infer specifics about the user’s interaction with the YouTube website, for example whether the video was searched for or visited as a result of a suggestion after viewing a previous video.The result of this research is a Python based prototype that will analyse a mounted disk image, automatically extract the artefacts related to YouTube visits and produce a report summarising the YouTube video accesses on a system.

  10. 东方百合杂种后代试管苗叶片总DNA提取方法的选择%Choosing Suitable Method to Extract Genomic DNA from the Leaves of In-tube Seedling of the Hybrid Offspring of Oriental Lily

    Institute of Scientific and Technical Information of China (English)

    胡凤荣; 国荣荣; 王斐; 王江勇

    2013-01-01

      以东方百合‘Sorbonne’בFrancia’的杂种后代试管苗叶片为材料,采用CTAB-高盐法、简易CTAB法、CTAB-硅珠法和SDS-CTAB法等4种DNA提取方法,比较DNA耗时、纯度、得率、浓度和质量等指标,以期为东方百合‘Sorbonne’בFrancia’杂种群体大量杂种后代试管苗叶片总DNA的提取筛选适宜方法.结果表明,除CTAB-硅珠法未获得DNA,其余3种方法均获得条带清晰、完整性好的DNA.在耗时方面, CTAB-硅珠法<简易CTAB法extract genomic DNA from the Leaves of in-tube seedling of oriental lily, the hybrids offspring derived from the cross of Sorbonne × Francia were used as the experimental materials in this study. We compared the DAN quality and extracting efficiency of the employed DNA extraction methods, such as SDS-CTAB, Simple and ease CTAB, CTAB-high salt precipitation and CTAB-silica purifi-cation, in the facets of the purity, yield, concentration, and time consuming to choosing the ideal DNA extraction method. Three methods can be used to extract DNA with good banding profiles and Integrity except CTAB-silica purification missing DNA. The orders of the time consuming were from more to less following as CTAB-silica purification, Simple and ease CTAB, CTAB-high salt precipitation and SDS-CTAB. In the term of DNA purity, the simple CTAB method got the highest DNA purity than that of the SDS-CTAB and CTAB-high salt precipitation, which the extracted DNA with the excellent quality with OD260/OD280, 1.98, OD260/OD230, 2.01;while the concentration of the extracted DNA reached 190.01 ng/μL as well as 57.01μg/g of the DNA yield. Above all, Simple and

  11. Hybrid endotracheal tubes

    Science.gov (United States)

    Sakezles, Christopher Thomas

    Intubation involves the placement of a tube into the tracheal lumen and is prescribed in any setting in which the airway must be stabilized or the patient anesthetized. The purpose of the endotracheal tube in these procedures is to maintain a viable airway, facilitate mechanical ventilation, allow the administration of anesthetics, and prevent the reflux of vomitus into the lungs. In order to satisfy these requirements a nearly airtight seal must be maintained between the tube and the tracheal lining. Most conventional endotracheal tubes provide this seal by employing a cuff that is inflated once the tube is in place. However, the design of this cuff and properties of the material are a source of irritation and injury to the tracheal tissues. In fact, the complication rate for endotracheal intubation is reported to be between 10 and 60%, with manifestations ranging from severe sore throat to erosion through the tracheal wall. These complications are caused by a combination of the materials employed and the forces exerted by the cuff on the tracheal tissues. In particular, the abrasive action of the cuff shears cells from the lining, epithelium adhering to the cuff is removed during extubation, and normal forces exerted on the basement tissues disrupt the blood supply and cause pressure necrosis. The complications associated with tracheal intubation may be reduced or eliminated by employing airway devices constructed from hydrogel materials. Hydrogels are a class of crosslinked polymers which swell in the presence of moisture, and may contain more than 95% water by weight. For the current study, several prototype airway devices were constructed from hydrogel materials including poly(vinyl alcohol), poly(hydroxyethyl methacrylate), and poly(vinyl pyrrolidone). The raw hydrogel materials from this group were subjected to tensile, swelling, and biocompatibility testing, while the finished devices were subjected to extensive mechanical simulation and animal trials

  12. Magneto-hydrodynamic detection of vortex shedding for molten salt flow sensing.

    Energy Technology Data Exchange (ETDEWEB)

    Kruizenga, Alan Michael; Crocker, Robert W.

    2012-09-01

    High temperature flow sensors must be developed for use with molten salts systems at temperatures in excess of 600ÀC. A novel magneto-hydrodynamic sensing approach was investigated. A prototype sensor was developed and tested in an aqueous sodium chloride solution as a surrogate for molten salt. Despite that the electrical conductivity was a factor of three less than molten salts, it was found that the electrical conductivity of an electrolyte was too low to adequately resolve the signal amidst surrounding noise. This sensor concept is expected to work well with any liquid metal application, as the generated magnetic field scales proportionately with electrical conductivity.

  13. Measurement and Analysis of Density of Molten Ni-W Alloys

    Institute of Scientific and Technical Information of China (English)

    FANG Liang; XIAO Feng; TAO Zainan; MuKai Kusuhiro

    2005-01-01

    The density of molten Ni-W alloys was measured with a modified pycnometric method. It is found that the density of the molten Ni- W alloys decreases with temperature rising, but increases with the increase of tungsten concentration in the alloys. The molar volume of molten Ni- W binary alloys increases with the increase of temperature and tungsten concentration. The partial molar volume of tungsten in liquid Ni- W binary alloy has been calculated approximately as ( - 1.59+ 5.64 × 10-3 T) × 10-6m3 ·mol-1.

  14. Hot corrosion monitoring of alloy 617 in molten chlorides using electrochemical techniques

    Energy Technology Data Exchange (ETDEWEB)

    Perez, F.J.; Hierro, M.P.; Nieto, J. [Univ. Complutense de Madrid (Spain). Dept. de Ciencia de los Materiales, Facultad de Ciencias Quimicas

    2006-07-01

    Molten chloride mixtures are formed in waste incineration plants during waste firing and energy production. These mixtures are responsible for degradation processes like hot corrosion. In order to evaluate the damage of molten salt mixtures in waste incineration environments, the alloy 617 was exposed beneath a molten KCl-ZnCl{sub 2} mixture at 650 C in air. The corrosion process was monitored by electrochemical impedance spectroscopy (EIS). An extensive microscopy analysis have been done in order to correlate the electrochemical results, and to establish an electrochemical mechanism for such high temperature corrosion process. (orig.)

  15. Electrodeposition of Ca Metal in CaCl2-CaO Molten Salt

    Institute of Scientific and Technical Information of China (English)

    GUO; Jun-kang; WANG; Chang-shui; CAO; Long-hao; OUYANG; Ying-gen

    2013-01-01

    To realize the continuouscalciothermic reduction in molten salts,the electrodeposition behavior of Ca metal in CaCl2-CaO molten salt was investigated by cylic voltammetry.The cyclic voltammograms at the scan rate of 100 mV/s are shown in Fig.1.As is shown,the electrodeposition potential of Ca deviated from-1.66 V to-0.97 V after CaO was added to molten CaCl2 and the decomposition of CaO

  16. Synthesis of TiNi/Ti2Ni Composite Particles in Molten Salts

    Institute of Scientific and Technical Information of China (English)

    YANG Rui-song; CUI Li-shan; ZHENG Yan-jun

    2006-01-01

    A new process of synthesizing TiNi/Ti2Ni composite particles, high temperature molten salts method, is introduced. This method uses molten salts as a reaction medium that does not take part in the chemical reaction and can be easily dissolved in rinsing water. According this method, the composite particles were prepared in molten salts at 700 ℃-900 ℃. By means of differential scanning calorimetry (DSC), the reversible martensitic transformation of TiNi particles in these composite particles was confirmed.

  17. Evaluation of Modified Pycnometric Method for Accurately Measuring the Density of Molten Nickel

    Institute of Scientific and Technical Information of China (English)

    XIAO Feng; FANG Liang; FU Yuechao; YANG Lingchuan

    2004-01-01

    A modified pycnometric method has been developed to obtain accurate densities of molten nickel.The new method allows continuous measurement of density over a wide temperature range from a single experiment.The measurement error of the method was analyzed, and the total uncertainty of the measurement was estimated to be within ±0.34%. The measured density of molten nickel decreases linearly with increasing temperature over a range from the melting point to 1873K. The density at the melting point and the thermal expansion coefficient of molten nickel are 7.90Mg·m-3 and 1.92×10-4 K-1,respectively.

  18. Spreading of molten corium in Mk I geometry following vessel meltthrough

    Energy Technology Data Exchange (ETDEWEB)

    Sienicki, J.J.; Farmer, M.T.; Spencer, B.W.

    1988-01-01

    A one-dimensional, multicell, Eulerian computer code is under development to predict the gravity-driven spreading dynamics and thermal interactions of a molten corium layer flowing horizontally over a concrete substrate. The code is compared to recent experiments in which molten mixtures of iron and aluminum oxide flowed over concrete in the presence and absence of water. Results are presented from scoping calculations for the Mk I BWR system investigating the spreading-induced penetration immediately following the drainage of a predominantly oxide molten corium mixture from a localized breach in the reactor vessel. 12 refs., 7 figs.

  19. Fragment structure from vapor explosions during the impact of molten metal droplets into a liquid pool

    Science.gov (United States)

    Kouraytem, Nadia; Li, Er Qiang; Vakarelski, Ivan Uriev; Thoroddsen, Sigurdur

    2015-11-01

    High-speed video imaging is used in order to look at the impact of a molten metal drop falling into a liquid pool. The interaction regimes are three: film boiling, nucleate boiling or vapor explosion. Following the vapor explosion, the metal fragments and different textures are observed. It was seen that, using a tin alloy, a porous structure results whereas using a distinctive eutectic metal, Field's metal, micro beads are formed. Different parameters such as the metal type, molten metal temperature, pool surface tension and pool boiling temperature have been altered in order to assess the role they play on the explosion dynamics and the molten metal's by product.

  20. In-tube magnetic solid phase microextraction of some fluoroquinolones based on the use of sodium dodecyl sulfate coated Fe3O4 nanoparticles packed tube.

    Science.gov (United States)

    Manbohi, Ahmad; Ahmadi, Seyyed Hamid

    2015-07-23

    In-tube magnetic solid phase microextraction (in-tube MSPME) of fluoroquinolones from water and urine samples based on the use of sodium dodecyl sulfate (SDS) coated Fe3O4 nanoparticles packed tube has been reported. After the preparation of Fe3O4 nanoparticles (NPs) by a batch synthesis, these NPs were introduced into a stainless steel tube by a syringe and then a strong magnet was placed around the tube, so that the Fe3O4 NPs were remained in the tube and the tube was used in the in-tube SPME-HPLC/UV for the analysis of fluoroquinolones in water and urine samples. Plackett-Burman design was employed for screening the variables significantly affecting the extraction efficiency. Then, the significant factors were more investigated by Box-Behnken design. Calibration curves were linear (R(2)>0.990) in the range of 0.1-1000μgL(-1) for ciprofloxacin (CIP) and 0.5-500μgL(-1) for enrofloxacin (ENR) and ofloxacin (OFL), respectively. LODs for all studied fluoroquinolones ranged from 0.01 to 0.05μgL(-1). The main advantages of this method were rapid and easy automation and analysis, short extraction time, high sensitivity, possibility of fully sorbent collection after analysis, wide linear range and no need to organic solvents in extraction. Copyright © 2015 Elsevier B.V. All rights reserved.

  1. Lava Tube Collapse Pits

    Science.gov (United States)

    2004-01-01

    [figure removed for brevity, see original site] We will be looking at collapse pits for the next two weeks. Collapse pits on Mars are formed in several ways. In volcanic areas, channelized lava flows can form roofs which insulate the flowing lava. These features are termed lava tubes on Earth and are common features in basaltic flows. After the lava has drained, parts of the roof of the tube will collapse under its own weight. These collapse pits will only be as deep as the bottom of the original lava tube. Another type of collapse feature associated with volcanic areas arises when very large eruptions completely evacuate the magma chamber beneath the volcano. The weight of the volcano will cause the entire edifice to subside into the void space below it. Structural features including fractures and graben will form during the subsidence. Many times collapse pits will form within the graben. In addition to volcanic collapse pits, Mars has many collapse pits formed when volatiles (such as subsurface ice) are released from the surface layers. As the volatiles leave, the weight of the surrounding rock causes collapse pits to form. These collapse pits are found in the southern hemisphere of Mars. They are likely lava tube collapse pits related to flows from Hadriaca Patera. Image information: VIS instrument. Latitude -36.8, Longitude 89.6 East (270.4 West). 19 meter/pixel resolution. Note: this THEMIS visual image has not been radiometrically nor geometrically calibrated for this preliminary release. An empirical correction has been performed to remove instrumental effects. A linear shift has been applied in the cross-track and down-track direction to approximate spacecraft and planetary motion. Fully calibrated and geometrically projected images will be released through the Planetary Data System in accordance with Project policies at a later time. NASA's Jet Propulsion Laboratory manages the 2001 Mars Odyssey mission for NASA's Office of Space Science, Washington, D

  2. Effects of alternative electromagnetic field on surface tension and filling ability of molten metal

    Institute of Scientific and Technical Information of China (English)

    HE Hong-liang; KANG Fu-wei; WANG Li-ping

    2005-01-01

    Surface tension and filling ability of molten metal play an important role on the shaping of the molten metal. The surface tension was calculated from wetting angles of the molten metal by the sessile drop method. The specimen for filling ability was designed and the filling ability experiments under the alternative electromagnetic field were performed. The results show that the intensity and frequency of the alternative electromagnetic field have significant effects on the surface tension of the molten metal. The surface tension of Al-6%Si alloy decreases with increasing the intensity of the electromagnetic field. For pure Sn, the surface tension decreases gradually when the frequency of electromagnetic field is reduced. The filling ability is improved by applying the alternative electromagnetic field.

  3. Viscosity of multi-component molten nitrate salts : liquidus to 200 degrees C.

    Energy Technology Data Exchange (ETDEWEB)

    Bradshaw, Robert W.

    2010-03-01

    The viscosity of molten salts comprising ternary and quaternary mixtures of the nitrates of sodium, potassium, lithium and calcium was determined experimentally. Viscosity was measured over the temperature range from near the relatively low liquidus temperatures of he individual mixtures to 200C. Molten salt mixtures that do not contain calcium nitrate exhibited relatively low viscosity and an Arrhenius temperature dependence. Molten salt mixtures that contained calcium nitrate were relatively more viscous and viscosity increased as the roportion of calcium nitrate increased. The temperature dependence of viscosity of molten salts containing calcium nitrate displayed curvature, rather than linearity, when plotted in Arrhenius format. Viscosity data for these mixtures were correlated by the Vogel-Fulcher- ammann-Hesse equation.

  4. Surface tension of molten Ni-(Cr, Co, W) alloys and segregation of elements

    Institute of Scientific and Technical Information of China (English)

    XIAO Feng; LIU Lan-xiao; YANG Ren-hui; ZHAO Hong-kai; FANG Liang; ZHANG Chi

    2008-01-01

    Surface tension of molten Ni-(Cr, Co, W) alloys was measured at the temperature of 1 773-1 873 K in an Ar+3%H2 atmosphere using an improved sessile drop method. The segregation of Cr, Co and W in alloy was calculated and analyzed using Butler's equation. The results show a good agreement between measured and calculated data. The surface tension of molten Ni-(Cr,Co, W) alloys decreases with increasing temperature. In Ni-(Cr, Co, W) alloys, the element with lower surface tension tends to segregate on the surface of molten alloy while that with higher surface tension tends to segregate inside of the molten alloy. The larger the differences in surface tension, atom radius and electron configuration between solvent and solute are, the more significant the segregation is. As a result, Ni segregates onto the surface and Co and W segregate inside the alloys.

  5. Molten Carbonate and Phosphoric Acid Stationary Fuel Cells: Overview and Gap Analysis

    Energy Technology Data Exchange (ETDEWEB)

    Remick, R.; Wheeler, D.

    2010-09-01

    This report describes the technical and cost gap analysis performed to identify pathways for reducing the costs of molten carbonate fuel cell (MCFC) and phosphoric acid fuel cell (PAFC) stationary fuel cell power plants.

  6. A Model for Molten Fuel-Coolant Interaction during Melt Slumping in a Nuclear Reactor

    Energy Technology Data Exchange (ETDEWEB)

    Sohal, Manohar Singh; Siefken, Larry James

    1999-10-01

    This paper describes a simple fuel melt slumping model to replace the current parametric model in SCDAP/RELAP5. Specifically, a fuel-coolant interaction (FCI) model is developed to analyze the slumping molten fuel, molten fuel breakup, heat transfer to coolant, relocation of the molten droplets, size of a partially solidified particles that settle to the bottom of the lower plenum, and melt-plenum interaction, if any. Considering our objectives, the molten fuel jet breakup model, and fuel droplets Lagrangian model as included in a code TEXAS-V with Eulerian thermal hydraulics for water and steam from SCDAP/RELAP5 were used. The model was assessed with experimental data from MAGICO-2000 tests performed at University of California at Santa Barbara, and FARO Test L-08 performed at Joint Research Center, Ispra, Italy. The comparison was found satisfactory.

  7. SURFACE TENSION OF MOLTEN IF STEEL CONTAINING Ti AND ITS INTERFACIAL PROPERTIES WITH SOLID ALUMINA

    Institute of Scientific and Technical Information of China (English)

    L.C. Zhong; M. Zeze; K. Mukai

    2004-01-01

    Surface tension of molten IF steel containing Ti and contact angle between the liquid steel and solid alumina were measured with sessile droplet method under Ar gas atmosphere at 1500, 1575 and 1600℃. The results show that titanium decreases the surface tension of the molten IF steel and the contact angle. The interfacial tension between the molten IF steel containing Ti and solid alumina decreases with increase in titanium content. The work of adhesion between molten IF steel containing Ti and solid alumina decreases slightly at 1550℃, but increases at 1600℃ with increasing titanium content. It can be deduced that fine bubbles and fine alumina inclusions are easily entrapped in solidifying interface for IF steel containing Ti.

  8. Mechanism of Gas Intrusion into Molten Metal during Horizontal Centrifugal Casting

    Institute of Scientific and Technical Information of China (English)

    NI Feng; ZHANG Xhan-ling; YANG Di-xin; BI Xiao-qin; ZHANG Yong-zhen

    2004-01-01

    A mechanism of gas intrusion into molten metal during horizontal centrifugal casting was introduced .Based upon this concept, a special pouring method was suggested ,which can effectively prevent the pinhole defects in horizontal centrifugal castings.

  9. High Surface Area Iridium Anodes and Melt Containers for Molten Oxide Electrolysis Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Direct electrochemical reduction of molten regolith is the most attractive method of oxygen production on the lunar surface, because no additional chemical reagents...

  10. Enhanced capacitive properties of commercial activated carbon by re-activation in molten carbonates

    Science.gov (United States)

    Lu, Beihu; Xiao, Zuoan; Zhu, Hua; Xiao, Wei; Wu, Wenlong; Wang, Dihua

    2015-12-01

    Simple, affordable and green methods to improve capacitive properties of commercial activated carbon (AC) are intriguing since ACs possess a predominant role in the commercial supercapacitor market. Herein, we report a green reactivation of commercial ACs by soaking ACs in molten Na2CO3-K2CO3 (equal in mass ratios) at 850 °C combining the merits of both physical and chemical activation strategies. The mechanism of molten carbonate treatment and structure-capacitive activity correlations of the ACs are rationalized. Characterizations show that the molten carbonate treatment increases the electrical conductivity of AC without compromising its porosity and wettability of electrolytes. Electrochemical tests show the treated AC exhibited higher specific capacitance, enhanced high-rate capability and excellent cycle performance, promising its practical application in supercapacitors. The present study confirms that the molten carbonate reactivation is a green and effective method to enhance capacitive properties of ACs.

  11. Proceedings of the workshop on molten salts technology and computer simulation

    Energy Technology Data Exchange (ETDEWEB)

    Hayashi, Hirokazu; Minato, Kazuo (eds.) [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

    2001-12-01

    Applications of molten salts technology to separation and synthesis of materials have been studied eagerly, which would develop new fields of materials science. Research Group for Actinides Science, Department of Materials Science, Japan Atomic Energy Research Institute (JAERI), together with Reprocessing and Recycle Technology Division, Atomic Energy Society of Japan, organized the Workshop on Molten Salts Technology and Computer Simulation at Tokai Research Establishment, JAERI on July 18, 2001. In the workshop eleven lectures were made and lively discussions were there on the fundamentals and applications of the molten salts technology that covered the structure and basic properties of molten salts, the pyrochemical reprocessing technology and the relevant computer simulation. The 10 of the presented papers are indexed individually. (J.P.N.)

  12. Molten-salt reactor program. Semiannual progress report for period ending February 29, 1976

    Energy Technology Data Exchange (ETDEWEB)

    McNeese, L.E.

    1976-08-01

    Separate abstracts and indexing were prepared for sections dealing with MSBR design and development; chemistry of fuel-salt and coolant-salt systems and analytical methods; materials development; fuel processing for molten-salt reactors; and salt production. (DG)

  13. Performance Testing of Molten Regolith Electrolysis with Transfer of Molten Material for the Production of Oxygen and Metals on the Moon

    Science.gov (United States)

    Sibille, Laurent; Sadoway, Donald; Tripathy, Prabhat; Standish, Evan; Sirk, Aislinn; Melendez, Orlando; Stefanescu, Doru

    2010-01-01

    Previously, we have demonstrated the production of oxygen by electrolysis of molten regolith simulants at temperatures near 1600 C. Using an inert anode and suitable cathode, direct electrolysis (no supporting electrolyte) of the molten silicate is carried out, resulting in the production of molten metallic products at the cathode and oxygen gas at the anode. Initial direct measurements of current efficiency have confirmed that the process offer potential advantages of high oxygen production rates in a smaller footprint facility landed on the moon, with a minimum of consumables brought from Earth. We now report the results of a scale-up effort toward the goal of achieving production rates equivalent to 1 metric ton O2/year, a benchmark established for the support of a lunar base. We previously reported on the electrochemical behavior of the molten electrolyte as dependent on anode material, sweep rate and electrolyte composition in batches of 20-200g and at currents of less than 0.5 A. In this paper, we present the results of experiments performed at currents up to 10 Amperes) and in larger volumes of regolith simulant (500 g - 1 kg) for longer durations of electrolysis. The technical development of critical design components is described, including: inert anodes capable of passing continuous currents of several Amperes, container materials selection, direct gas analysis capability to determine the gas components co-evolving with oxygen. To allow a continuous process, a system has been designed and tested to enable the withdrawal of cathodically-reduced molten metals and spent molten oxide electrolyte. The performance of the withdrawal system is presented and critiqued. The design of the electrolytic cell and the configuration of the furnace were supported by modeling the thermal environment of the system in an effort to realize a balance between external heating and internal joule heating. We will discuss the impact these simulations and experimental findings have

  14. Tube coalescence in the Jingfudong lava tube and implications for lava flow hazard of Tengchong volcanism

    OpenAIRE

    Zhengquan Chen; Yongshun Liu; Haiquan Wei; Jiandong Xu; Wenfeng Guo

    2016-01-01

    Tube-fed structure occurs as a general phenomenon in Tengchong basic lavas, such as lava tubes, lava plugs and tube-related collapse depressions. We deduced the development of Laoguipo lava flows, which is the longest lava tube (Jingfudong lava tube) evolved in Tengchong volcanic area. Following the detailed documentation of the tube morphology of the Jingfudong lava tube, we propose that the Jingfudong lava tube was formed through vertical coalescence of at least three tubes. The coalescence...

  15. Electrochemical interaction between graphite and molten salts to produce nanotubes, nanoparticles, graphene and nanodiamonds

    OpenAIRE

    2015-01-01

    This is the author accepted manuscript. The final version is available from Springer via http://dx.doi.org/10.1007/s10853-015-9340-2 The electrochemical interaction between graphite and molten salts to produce carbon nanostructures is reviewed. It is demonstrated that, depending on the conditions, it is possible to electrochemically convert graphite in molten salts to either carbon nanoparticles and nanotubes, metal filled carbon nanoparticles and nanotubes, graphene or nanodiamonds. The...

  16. Resistivity Measurement of Molten Olivine in a Laser-Heated Diamond Anvil Cell

    Institute of Scientific and Technical Information of China (English)

    LI Ming; GAO Chun-Xiao; MA Yan-Zhang; HE Chun-Yuan; HAO Ai-Min; ZHANG Dong-Mei; LI Yan-Chun; LIU Jing; WANG Duo-Jun

    2007-01-01

    The electrical conductivity of molten olivine is studied up to 3720 K and 13.2 GPa.The results indicate that the electrical conductivity of molten olivine exhibits the perfect Arrhenivs behaviour.The activation energy as well as temperature effect is much smaller than that of the solid olivine.It is expected that the high conductivity zone in the mantle is almost independent of the melting based on our experimental data.

  17. Advanced Thermal Storage System with Novel Molten Salt: December 8, 2011 - April 30, 2013

    Energy Technology Data Exchange (ETDEWEB)

    Jonemann, M.

    2013-05-01

    Final technical progress report of Halotechnics Subcontract No. NEU-2-11979-01. Halotechnics has demonstrated an advanced thermal energy storage system with a novel molten salt operating at 700 degrees C. The molten salt and storage system will enable the use of advanced power cycles such as supercritical steam and supercritical carbon dioxide in next generation CSP plants. The salt consists of low cost, earth abundant materials.

  18. Molten-Salt Batteries for Medium and Large-Scale Energy Storage

    Energy Technology Data Exchange (ETDEWEB)

    Lu, Xiaochuan; Yang, Zhenguo (Gary)

    2014-12-01

    This chapter discusses two types of molten salt batteries. Both of them are based on a beta-alumina solid electrolyte and molten sodium anode, i.e., sodium-sulfur (Na-S) battery and sodium-metal halide (ZEBRA) batteries. The chapter first reviews the basic electrochemistries and materials for various battery components. It then describes the performance of state-of-the-art batteries and future direction in material development for these batteries.

  19. Growing Uniform Graphene Disks and Films on Molten Glass for Heating Devices and Cell Culture.

    Science.gov (United States)

    Chen, Yubin; Sun, Jingyu; Gao, Junfeng; Du, Feng; Han, Qi; Nie, Yufeng; Chen, Zhaolong; Bachmatiuk, Alicja; Priydarshi, Manish Kr; Ma, Donglin; Song, Xiuju; Wu, Xiaosong; Xiong, Chunyang; Rümmeli, Mark H; Ding, Feng; Zhang, Yanfeng; Liu, Zhongfan

    2015-12-16

    The direct growth of uniform graphene disks and their continuous film is achieved by exploiting the molten state of glass. The use of molten glass enables highly uniform nucleation and an enhanced growth rate (tenfold) of graphene, as compared to those scenarios on commonly used insulating solids. The obtained graphene glasses show promising application potentials in daily-life scenarios such as smart heating devices and biocompatible cell-culture mediums.

  20. Prediction of the thermophysical properties of molten salt fast reactor fuel from first-principles

    OpenAIRE

    Gheribi, Aimen; Corradini, D; Dewan, L. (Lawrence); Chartrand, P; Simon, C.; Madden, Paul,; M. Salanne

    2014-01-01

    International audience; Molten fluorides are known to show favorable thermophysical properties which make them good candidate coolants for nuclear fission reactors. Here we investigate the special case of mixtures of lithium fluoride and thorium fluoride, which act both as coolant and fuel in the molten salt fast reactor concept. By using ab initio parameterized polarizable force fields, we show that it is possible to calculate the whole set of properties (density, thermal expansion, heat cap...

  1. Thermal Energy Storage in Molten Salts: Overview of Novel Concepts and the DLR Test Facility (TESIS)

    OpenAIRE

    2016-01-01

    At present, two-tank molten salt storage systems are the established commercially available concept for solar thermal power plants. Due to their very low vapour pressure and comparatively high thermal stability, molten salts are preferred as the heat transfer fluid and storage medium. Therefore, the development of alternative, more cost-effective concepts is an important step in making thermal energy storage more competitive for industrial processes and solar thermal applications. The pape...

  2. Electrochemical reduction of metal oxides in molten salts for nuclear reprocessing

    OpenAIRE

    Abdulaziz, R.

    2016-01-01

    This thesis examines the electrochemical reduction of metal oxides in molten salts for nuclear reprocessing applications. The objective of this research is to characterise and understand the direct electrochemical reduction of UO₂ to U metal in a LiCl-KCl molten salt eutectic, as part of the nuclear pyroprocessing scheme, following a similar approach to the FFC Cambridge for the reduction of TiO₂ to Ti metal. The voltammetric behaviour of reduction processes of metal oxides were evaluated usi...

  3. Steam generator tube integrity program

    Energy Technology Data Exchange (ETDEWEB)

    Dierks, D.R.; Shack, W.J. [Argonne National Laboratory, IL (United States); Muscara, J.

    1996-03-01

    A new research program on steam generator tubing degradation is being sponsored by the U.S. Nuclear Regulatory Commission (NRC) at Argonne National Laboratory. This program is intended to support a performance-based steam generator tube integrity rule. Critical areas addressed by the program include evaluation of the processes used for the in-service inspection of steam generator tubes and recommendations for improving the reliability and accuracy of inspections; validation and improvement of correlations for evaluating integrity and leakage of degraded steam generator tubes, and validation and improvement of correlations and models for predicting degradation in steam generator tubes as aging occurs. The studies will focus on mill-annealed Alloy 600 tubing, however, tests will also be performed on replacement materials such as thermally-treated Alloy 600 or 690. An overview of the technical work planned for the program is given.

  4. High-Temperature Corrosion of Protective Coatings for Boiler Tubes in Thermal Power Plants

    Institute of Scientific and Technical Information of China (English)

    XU Lianyong; JING Hongyang; HUO Lixing

    2005-01-01

    High-temperature corrosion is a serious problem for the water-wall tubes of boilers used in thermal power plants. Oxidation, sulfidation and molten salt corrosion are main corrosion ways.Thereinto, the most severe corrosion occurs in molten salt corrosion environment. Materials rich in oxides formers, such as chromium and aluminum, are needed to resist corrosion in high-temperature and corrosive environment, but processability of such bulk alloys is very limited. High velocity electric arc spraying (HVAS) technology is adopted to produce coatings with high corrosion resistance. By comparison, NiCr (Ni-45Cr-4Ti) is recommended as a promising alloy coating for the water-wall tubes, which can even resist molten salt corrosion attack. In the study of corrosion mechanism, the modern material analysis methods, such as scanning electron microscopy (SEM), X-ray diffractometry (XRD) and energy dispersive spectrometry (EDS), are used. It is found that the corrosion resistances of NiCr and FeCrAI coatings are much better than that of 20g steel, that the NiCr coatings have the best anti-corrosion properties, and that the NiCr coatings have slightly lower pores than FeCrAI coatings.It is testified that corrosion resistance of coatings is mainly determined by chromium content, and the microstructure of a coating is as important as the chemical composition of the material. In addition, the fracture mechanisms of coatings in the cycle of heating and cooling are put forward. The difference of the thermal physical properties between coatings and base metals results in the thermal stress inside the coatings. Consequently, the coatings spall from the base metal.

  5. Diffusion in a Curved Tube

    OpenAIRE

    Ogawa, Naohisa

    2011-01-01

    The diffusion of particles in confining walls forming a tube is discussed. Such a transport phenomenon is observed in biological cells and porous media. We consider the case in which the tube is winding with curvature and torsion, and the thickness of the tube is sufficiently small compared with its curvature radius. We discuss how geomerical quantities appear in a quasi-one-dimensional diffusion equation.

  6. The special relativistic shock tube

    Science.gov (United States)

    Thompson, Kevin W.

    1986-01-01

    The shock-tube problem has served as a popular test for numerical hydrodynamics codes. The development of relativistic hydrodynamics codes has created a need for a similar test problem in relativistic hydrodynamics. The analytical solution to the special relativistic shock-tube problem is presented here. The relativistic shock-jump conditions and rarefaction solution which make up the shock tube are derived. The Newtonian limit of the calculations is given throughout.

  7. Tubing for augmented heat transfer

    Energy Technology Data Exchange (ETDEWEB)

    Yampolsky, J.S.; Pavlics, P.

    1983-08-01

    The objectives of the program reported were: to determine the heat transfer and friction characteristics on the outside of spiral fluted tubing in single phase flow of water, and to assess the relative cost of a heat exchanger constructed with spiral fluted tubing with one using conventional smooth tubing. An application is examined where an isolation water/water heat exchanger was used to transfer the heat from a gaseous diffusion plant to an external system for energy recovery. (LEW)

  8. Proton conducting ceramics for potentiometric hydrogen sensors for molten metals

    Energy Technology Data Exchange (ETDEWEB)

    Borland, H.; Llivina, L.; Colominas, S.; Abellà, J., E-mail: jordi.abella@iqs.edu

    2013-10-15

    Highlights: • Synthesis and chemical characterization of proton conductor ceramics. • Qualification of ceramics for hydrogen sensors in molten lithium–lead. • Ceramics have well-defined grains with a wide distribution of sizes. • Good agreement with predictions obtained with BaZrY, BaCeZrY and SrFeCo ceramics. -- Abstract: Tritium monitoring in lithium–lead eutectic (Pb–15.7Li) is of great importance for the performance of liquid blankets in fusion reactors. Also, tritium measurements will be required in order to proof tritium self-sufficiency in liquid metal breeding systems. On-line hydrogen (isotopes) sensors must be design and tested in order to accomplish these goals. Potentiometric hydrogen sensors for molten lithium–lead eutectic have been designed at the Electrochemical Methods Lab at Institut Quimic de Sarria (IQS) at Barcelona and are under development and qualification. The probes are based on the use of solid state electrolytes and works as proton exchange membranes (PEM). In this work the following compounds: BaZr{sub 0.9}Y{sub 0.1}O{sub 3}, BaCe{sub 0.6}Zr{sub 0.3}Y{sub 0.1}O{sub 3−α}, Sr(Ce{sub 0.6}-Zr{sub 0.4}){sub 0.9}Y{sub 0.1}O{sub 3−α} and Sr{sub 3}Fe{sub 1.8}Co{sub 2}O{sub 7} have been synthesized in order to be tested as PEM H-probes. Potentiometric measurements of the synthesized ceramic elements at 500 °C have been performed at a fixed hydrogen concentration. The sensors constructed using the proton conductor elements BaZr{sub 0.9}Y{sub 0.1}O{sub 3}, BaCe{sub 0.6}Zr{sub 0.3}Y{sub 0.1}O{sub 3−δ} and Sr{sub 3}Fe{sub 1.8}Co{sub 0.2}O{sub 7−δ} exhibited stable output potential and its value was close to the theoretical value calculated with the Nernst equation (deviation around 60 mV). In contrast, the sensor constructed using the proton conductor element Sr(Ce{sub 0.6}–Zr{sub 0.4}){sub 0.9}Y{sub 0.1}O{sub 3−δ} showed a deviation higher than 100 mV between experimental an theoretical data.

  9. Molten Salt: Concept Definition and Capital Cost Estimate

    Energy Technology Data Exchange (ETDEWEB)

    Stoddard, Larry [Black & Veatch, Kansas City, MO (United States); Andrew, Daniel [Black & Veatch, Kansas City, MO (United States); Adams, Shannon [Black & Veatch, Kansas City, MO (United States); Galluzzo, Geoff [Black & Veatch, Kansas City, MO (United States)

    2016-06-30

    The Department of Energy’s (DOE’s) Office of Renewable Power (ORP) has been tasked to provide effective program management and strategic direction for all of the DOE’s Energy Efficiency & Renewable Energy’s (EERE’s) renewable power programs. The ORP’s efforts to accomplish this mission are aligned with national energy policies, DOE strategic planning, EERE’s strategic planning, Congressional appropriation, and stakeholder advice. ORP is supported by three renewable energy offices, of which one is the Solar Energy Technology Office (SETO) whose SunShot Initiative has a mission to accelerate research, development and large scale deployment of solar technologies in the United States. SETO has a goal of reducing the cost of Concentrating Solar Power (CSP) by 75 percent of 2010 costs by 2020 to reach parity with base-load energy rates, and to reduce costs 30 percent further by 2030. The SunShot Initiative is promoting the implementation of high temperature CSP with thermal energy storage allowing generation during high demand hours. The SunShot Initiative has funded significant research and development work on component testing, with attention to high temperature molten salts, heliostats, receiver designs, and high efficiency high temperature supercritical CO2 (sCO2) cycles. DOE retained Black & Veatch to support SETO’s SunShot Initiative for CSP solar power tower technology in the following areas: 1. Concept definition, including costs and schedule, of a flexible test facility to be used to test and prove components in part to support financing. 2. Concept definition, including costs and schedule, of an integrated high temperature molten salt (MS) facility with thermal energy storage and with a supercritical CO2 cycle generating approximately 10MWe. 3. Concept definition, including costs and schedule, of an integrated high temperature falling particle facility with thermal energy storage and with a supercritical CO2

  10. Development of Channeled Flow in Partially Molten Medium

    Science.gov (United States)

    Takashima, S.; Kumagai, I.; Kurita, K.

    2002-12-01

    There exist two contrasting models as to the style of melt migration in the partially molten medium; homogeneous permeable flow on grain scale and heterogeneous localized one (channeled flow on larger scale than the grain scale). It is considered that the style evolves from the homogeneous flow to the heterogeneous one as the degree of melting increases, but the physics responsible for this flow organization is not yet clarified. Several models as to this process and the melt segregation are proposed based on numerical simulation, though the experimental verification is not given yet. Here we present simple experimental results on the flow organization. We utilized highly deformable transparent gel as the solid phase. Due to this high deformability the matrix composed of the gel is easy to vary its internal structure. We have conducted the following experiments; the gel (about 5mm in diameter) is mingled with methyl-cellulose solution (MS) with almost same density as the gel, 1.01g/cm3, packed in a rectangular parallelepiped case (2.4cm*18cm*14.4cm), and a compaction state is realized by covering with wire netting at the upper boundary. Gel fraction of this mixture system is controlled by changing the ratio of the gel to MS (about 100% to 60%). Glycerol solution (GS) with density of 1.2g/cm3 is poured at the upper boundary. This is a kind of Rayleigh-Taylor Instability and the dense GS flows downward through the mixture. The flow pattern of the GS is analyzed. A series of these procedures is carried out at various gel fractions (from about 100% to 60%), and how the flow style varies with the gel fraction is investigated. At median fraction of the gel about 80% to 70% the evolution from homogeneous permeable flow to heterogeneous localized flow was observed. At higher gel fraction, liquid phase flows as homogeneous permeable flow. Fragility of the solid frame is a most important factor for flow organization. The structure of the partially molten medium can be easily

  11. Development of lava tubes in the light of observations at Mauna Ulu, Kilauea Volcano, Hawaii

    Science.gov (United States)

    Peterson, D.W.; Holcomb, R.T.; Tilling, R.I.; Christiansen, R.L.

    1994-01-01

    During the 1969-1974 Mauna Ulu eruption on Kilauea's upper east rift zone, lava tubes were observed to develop by four principal processes: (1) flat, rooted crusts grew across streams within confined channels; (2) overflows and spatter accreted to levees to build arched roofs across streams; (3) plates of solidified crust floating downstream coalesced to form a roof; and (4) pahoehoe lobes progressively extended, fed by networks of distributaries beneath a solidified crust. Still another tube-forming process operated when pahoehoe entered the ocean; large waves would abruptly chill a crust across the entire surface of a molten stream crossing through the surf zone. These littoral lava tubes formed abruptly, in contrast to subaerial tubes, which formed gradually. All tube-forming processes were favored by low to moderate volume-rates of flow for sustained periods of time. Tubes thereby became ubiquitous within the pahoehoe flows and distributed a very large proportionof the lava that was produced during this prolonged eruption. Tubes transport lava efficiently. Once formed, the roofs of tubes insulate the active streams within, allowing the lava to retain its fluidity for a longer time than if exposed directly to ambient air temperature. Thus the flows can travel greater distances and spread over wider areas. Even though supply rates during most of 1970-1974 were moderate, ranging from 1 to 5 m3/s, large tube systems conducted lava as far as the coast, 12-13 km distant, where they fed extensive pahoehoe fields on the coastal flats. Some flows entered the sea to build lava deltas and add new land to the island. The largest and most efficient tubes developed during periods of sustained extrusion, when new lava was being supplied at nearly constant rates. Tubes can play a major role in building volcanic edifices with gentle slopes because they can deliver a substantial fraction of lava erupted at low to moderate rates to sites far down the flank of a volcano. We

  12. Getting in shape: molten wax drop deformation and solidification at an immiscible liquid interface.

    Science.gov (United States)

    Beesabathuni, Shilpa N; Lindberg, Seth E; Caggioni, Marco; Wesner, Chris; Shen, Amy Q

    2015-05-01

    The controlled production of non-spherical shaped particles is important for many applications such as food processing, consumer goods, adsorbents, drug delivery, and optical sensing. In this paper, we investigated the deformation and simultaneous solidification of millimeter size molten wax drops as they impacted an immiscible liquid interface of higher density. By varying initial temperature and viscoelasticity of the molten drop, drop size, impact velocity, viscosity and temperature of the bath fluid, and the interfacial tension between the molten wax and bath fluid, spherical molten wax drops impinged on a cooling water bath and were arrested into non-spherical solidified particles in the form of ellipsoid, mushroom, disc, and flake-like shapes. We constructed cursory phase diagrams for the various particle shapes generated over a range of Weber, Capillary, Reynolds, and Stefan numbers, governed by the interfacial, inertial, viscous, and thermal effects. We solved a simplified heat transfer problem to estimate the time required to initiate the solidification at the interface of a spherical molten wax droplet and cooling aqueous bath after impact. By correlating this time with the molten wax drop deformation history captured from high speed imaging experiments, we elucidate the delicate balance of interfacial, inertial, viscous, and thermal forces that determine the final morphology of wax particles.

  13. Comparison of molten chloride and fluoride salts potentialities for An/Ln separation by electrodeposition

    Energy Technology Data Exchange (ETDEWEB)

    Laplace, A.; Peron, F.; Marrot, F.; Lacquement, J. [DRCP/SCPS/LPP - CEA/CEN Valrho - BP 17171 - 30207 Bagnols/Ceze (France)

    2008-07-01

    The objective of this paper is the comparison of molten fluoride and chloride salts potentialities for Am/Nd separation by electrodeposition on inert cathode, on a purely thermodynamic point of view. The molten LiF-CaF{sub 2} eutectic (77-23 mol.%, at 780 deg. C) was considered for this study. Cyclic voltammetry showed a one step Am(III)/Am reduction at a potential of {approx_equal}+0.5 V vs. Li{sup +}/Li. A potential difference of 290 mV between Am and Nd metallic deposition was estimated by square-wave voltammetry. This Am/Nd potential difference is more important than in molten chlorides (220 mV in the LiCl-KCl eutectic at 500 deg. C). Moreover in molten fluoride salt, the americium and neodymium (+II) oxidation state is not stable contrary to the molten chloride one where corrosion of deposited Am would be potential. However this larger potential difference in molten fluorides is quite balanced by the higher working temperature. (authors)

  14. Alternate tube plugging criteria for steam generator tubes

    Energy Technology Data Exchange (ETDEWEB)

    Cueto-Felgueroso, C.; Aparicio, C.B. [Tecnatom, S.A., Madrid (Spain)

    1997-02-01

    The tubing of the Steam Generators constitutes more than half of the reactor coolant pressure boundary. Specific requirements governing the maintenance of steam generator tubes integrity are set in Plant Technical Specifications and in Section XI of the ASME Boiler and Pressure Vessel Code. The operating experience of Steam Generator tubes of PWR plants has shown the existence of some types of degradatory processes. Every one of these has an specific cause and affects one or more zones of the tubes. In the case of Spanish Power Plants, and depending on the particular Plant considered, they should be mentioned the Primary Water Stress Corrosion Cracking (PWSCC) at the roll transition zone (RTZ), the Outside Diameter Stress Corrosion Cracking (ODSCC) at the Tube Support Plate (TSP) intersections and the fretting with the Anti-Vibration Bars (AVBs) or with the Support Plates in the preheater zone. The In-Service Inspections by Eddy Currents constitutes the standard method for assuring the SG tubes integrity and they permit the monitoring of the defects during the service life of the plant. When the degradation reaches a determined limit, called the plugging limit, the SG tube must be either repaired or retired from service by plugging. Customarily, the plugging limit is related to the depth of the defect. Such depth is typically 40% of the wall thickness of the tube and is applicable to any type of defect in the tube. In its origin, that limit was established for tubes thinned by wastage, which was the predominant degradation in the seventies. The application of this criterion for axial crack-like defects, as, for instance, those due to PWSCC in the roll transition zone, has lead to an excessive and unnecessary number of tubes being plugged. This has lead to the development of defect specific plugging criteria. Examples of the application of such criteria are discussed in the article.

  15. Learning from YouTube [Video Book

    Science.gov (United States)

    Juhasz, Alexandra

    2011-01-01

    YouTube is a mess. YouTube is for amateurs. YouTube dissolves the real. YouTube is host to inconceivable combos. YouTube is best for corporate-made community. YouTube is badly baked. These are a few of the things Media Studies professor Alexandra Juhasz (and her class) learned about YouTube when she set out to investigate what actually happens…

  16. Method for producing a tube

    Science.gov (United States)

    Peterson, Kenneth A.; Rohde, Steven B.; Pfeifer, Kent B.; Turner, Timothy S.

    2007-01-02

    A method is described for producing tubular substrates having parallel spaced concentric rings of electrical conductors that can be used as the drift tube of an Ion Mobility Spectrometer (IMS). The invention comprises providing electrodes on the inside of a tube that are electrically connected to the outside of the tube through conductors that extend between adjacent plies of substrate that are combined to form the tube. Tubular substrates are formed from flexible polymeric printed wiring board materials, ceramic materials and material compositions of glass and ceramic, commonly known as Low Temperature Co-Fired Ceramic (LTCC). The adjacent plies are sealed together around the electrode.

  17. YouTube and 'psychiatry'.

    Science.gov (United States)

    Gordon, Robert; Miller, John; Collins, Noel

    2015-12-01

    YouTube is a video-sharing website that is increasingly used to share and disseminate health-related information, particularly among younger people. There are reports that social media sites, such as YouTube, are being used to communicate an anti-psychiatry message but this has never been confirmed in any published analysis of YouTube clip content. This descriptive study revealed that the representation of 'psychiatry' during summer 2012 was predominantly negative. A subsequent smaller re-analysis suggests that the negative portrayal of 'psychiatry' on YouTube is a stable phenomenon. The significance of this and how it could be addressed are discussed.

  18. Charm production in flux tubes

    CERN Document Server

    Aguiar, C E; Nazareth, R A M S; Pech, G

    1996-01-01

    We argue that the non-perturbative Schwinger mechanism may play an important role in the hadronic production of charm. We present a flux tube model which assumes that the colliding hadrons become color charged because of gluon exchange, and that a single non-elementary flux tube is built up as they recede. The strong chromoelectric field inside this tube creates quark pairs (including charmed ones) and the ensuing color screening breaks the tube into excited hadronic clusters. On their turn these clusters, or `fireballs', decay statistically into the final hadrons. The model is able to account for the soft production of charmed, strange and lighter hadrons within a unified framework.

  19. Charm production in flux tubes

    Science.gov (United States)

    Aguiar, C. E.; Kodama, T.; Nazareth, R. A. M. S.; Pech, G.

    1996-01-01

    We argue that the nonperturbative Schwinger mechanism may play an important role in the hadronic production of charm. We present a flux tube model which assumes that the colliding hadrons become color charged because of gluon exchange, and that a single nonelementary flux tube is built up as they recede. The strong chromoelectric field inside this tube creates quark pairs (including charmed ones) and the ensuing color screening breaks the tube into excited hadronic clusters. In their turn these clusters, or ``fireballs,'' decay statistically into the final hadrons. The model is able to account for the soft production of charmed, strange, and lighter hadrons within a unified framework.

  20. The Effective Convectivity Model for Simulation of Molten Metal Layer Heat Transfer in a Boiling Water Reactor Lower Head

    Directory of Open Access Journals (Sweden)

    Chi-Thanh Tran

    2013-01-01

    Full Text Available This paper is concerned with the development of approaches for assessment of core debris heat transfer and Control Rod Guide Tube (CRGT cooling effectiveness in case of a Boiling Water Reactor (BWR severe accident. We consider a hypothetical scenario with stratified (metal layer atop melt pool in the lower plenum. Effective Convectivity Model (ECM and Phase-Change ECM (PECM are developed for the modeling of molten metal layer heat transfer. The PECM model takes into account reduced convection heat transfer in mushy zone and compositional convection that enables simulations of noneutectic binary mixture solidification and melting. The ECM and PECM are (i validated against relevant experiments for both eutectic and noneutectic mixtures and (ii benchmarked against CFD-generated data including the local heat transfer characteristics. The PECM is then applied to the analysis of heat transfer in a stratified heterogeneous debris pool taking into account CRGT cooling. The PECM simulation results show apparent efficacy of the CRGT cooling which can be utilized as Severe Accident Management (SAM measure to protect the vessel wall from focusing effect caused by metallic layer.

  1. Effect of the sequence of tube rolling in a tube bundle of a shell and tube heat exchanger on the stress-deformed state of the tube sheet

    Science.gov (United States)

    Tselishchev, M. F.; Plotnikov, P. N.; Brodov, Yu. M.

    2015-11-01

    Rolling the tube sheet of a heat exchanger with U-shaped tubes, as exemplified by the vapor cooler GP-24, was simulated. The simulation was performed using the finite element method with account of elas- tic-plastic properties of the tube and tube sheet materials. The simulation consisted of two stages; at the first stage, maximum and residual contact stress in the conjunction of a separate tube and the tube sheet was determined using the "equivalent sleeve" model; at the second stage, the obtained contact stress was applied to the hole surface in the tube sheet. Thus, different tube rolling sequences were simulated: from the center to the periphery of the tube sheet and from the periphery to the center along a spiral line. The studies showed that the tube rolling sequence noticeably influences the value of the tube sheet residual deflection for the same rolling parameters of separate tubes. Residual deflection of the tube sheet in different planes was determined. It was established that the smallest residual deflection corresponds to the tube rolling sequence from the periphery to the center of the tube sheet. The following dependences were obtained for different rolling sequences: maximum deformation of the tube sheet as a function of the number of rolled tubes, residual deformation of the tube sheet along its surface, and residual deflection of the tube sheet as a function of the rotation angle at the periphery. The preferred sequence of tube rolling for minimizing the tube sheet deformation is indicated.

  2. Infrared imaging of LED lighting tubes and fluorescent tubes

    Science.gov (United States)

    Siikanen, Sami; Kivi, Sini; Kauppinen, Timo; Juuti, Mikko

    2011-05-01

    The low energy efficiency of conventional light sources is mainly caused by generation of waste heat. We used infrared (IR) imaging in order to monitor the heating of both LED tube luminaires and ordinary T8 fluorescent tubes. The IR images showed clearly how the surface temperatures of the fluorescent tube ends quickly rose up to about +50...+70°C, whereas the highest surface temperatures seen on the LED tubes were only about +30...+40°C. The IR images demonstrated how the heat produced by the individual LED chips can be efficiently guided to the supporting structure in order to keep the LED emitters cool and hence maintain efficient operation. The consumed electrical power and produced illuminance were also recorded during 24 hour measurements. In order to assess the total luminous efficacy of the luminaires, separate luminous flux measurements were made in a large integrating sphere. The currently available LED tubes showed efficacies of up to 88 lm/W, whereas a standard "cool white" T8 fluorescent tube produced ca. 75 lm/W. Both lamp types gave ca. 110 - 130 lx right below the ceiling-mounted luminaire, but the LED tubes consume only 40 - 55% of the electric power compared to fluorescent tubes.

  3. Assessment of commercial prospects of molten carbonate fuel cells

    Science.gov (United States)

    Dicks, Andrew; Siddle, Angie

    The commercial prospects of molten carbonate fuel cells have been evaluated. Market applications, and the commercial criteria that the MCFC will need to satisfy for these applications, were identified through interviews with leading MCFC developers. Strengths, weaknesses, opportunities and threats (SWOT) analyses were carried out to critically evaluate the prospects for commercialisation. There are many competing technologies, but it is anticipated that MCFCs can make significant penetration into markets where their attributes, such as quality of power, low emissions and availability, give them a leading position in comparison with, for example, engine and turbine-based power generation systems. Analysis suggests that choosing the size for MCFC plant is more important than the target market sector/niche. Opportunities will exist in many market sectors, though the commercial market would be easier to penetrate initially. Developers are optimistic about the commercial prospects for the MCFC. Most believe that early commercial MCFC plants may start to appear in the first decade of the next century, the earliest date suggested for initial market entry being 2002.

  4. Molten pool characterization of laser lap welded copper and aluminum

    Science.gov (United States)

    Xue, Zhiqing; Hu, Shengsun; Zuo, Di; Cai, Wayne; Lee, Dongkyun; Elijah, Kannatey-Asibu, Jr.

    2013-12-01

    A 3D finite volume simulation model for laser welding of a Cu-Al lap joint was developed using ANSYS FLUENT to predict the weld pool temperature distribution, velocity field, geometry, alloying element distribution and transition layer thickness—all key attributes and performance characteristics for a laser-welded joint. Melting and solidification of the weld pool was simulated with an enthalpy-porosity formulation. Laser welding experiments and metallographic examination by SEM and EDX were performed to investigate the weld pool features and validate the simulated results. A bowl-shaped temperature field and molten pool, and a unique maximum fusion zone width were observed near the Cu-Al interface. Both the numerical simulation and experimental results indicate an arch-shaped intermediate layer of Cu and Al, and a gradual transition of Cu concentration from the aluminum plate to the copper plate with high composition gradient. For the conditions used, welding with Cu on top was found to result in a better weld joint.

  5. High-temperature molten salt thermal energy storage systems

    Science.gov (United States)

    Petri, R. J.; Claar, T. D.; Tison, R. R.; Marianowski, L. G.

    1980-02-01

    The results of comparative screening studies of candidate molten carbonate salts as phase change materials (PCM) for advanced solar thermal energy storage applications at 540 to 870 C (1004 to 1600 F) and steam Rankine electric generation at 400 to 540 C (752 to 1004 F) are presented. Alkali carbonates are attractive as latent heat storage materials because of their relatively high storage capacity and thermal conductivity, low corrosivity, moderate cost, and safe and simple handling requirements. Salts were tested in 0.1 kWhr lab scale modules and evaluated on the basis of discharge heat flux, solidification temperature range, thermal cycling stability, and compatibility with containment materials. The feasibility of using a distributed network of high conductivity material to increase the heat flux through the layer of solidified salt was evaluated. The thermal performance of an 8 kWhr thermal energy storage (TES) module containing LiKCO3 remained very stable throughout 5650 hours and 130 charge/discharge cycles at 480 to 535 C (896 to 995 F). A TES utilization concept of an electrical generation peaking subsystem composed of a multistage condensing steam turbine and a TES subsystem with a separate power conversion loop was defined. Conceptual designs for a 100 MW sub e TES peaking system providing steam at 316 C, 427 C, and 454 C (600 F, 800 F, and 850 F) at 3.79 million Pa (550 psia) were developed and evaluated. Areas requiring further investigation have also been identified.

  6. Dynamics of Molten Metal Droplets Falling on a Solid Surface

    Science.gov (United States)

    Chandra, Sanjeev; Aziz, Shiraz

    1997-11-01

    Experiments were done to photograph the impact of molten tin droplets impacting on a stainless steel surface. Initial droplet temperature was maintained at 240 C (slightly above the melting point of tin, 232 C). Impact velocity was varied from 1 m/s to 4 m/s and initial surface temperatures from 25 C to 240 C. Droplet dimensions and the evolution of liquid-solid contact angle during impact were measured from photographs. Droplets were observed to spread into the shape of a flat disc after impact. Once they reached their maximum extension they either stayed in that position or recoiled off the surface. A simple energy conservation model is proposed to predict the maximum spread diameter. Droplet recoil was attributed to surface tension pulling back the periphery of the splat. Increasing droplet impact velocity produced splashing, with a ring of satellite droplets breaking loose from the periphery. A model based on the Rayleigh-Taylor instability was used to predict the number of droplets that broke loose after impact.

  7. Molten salt synthesis of mullite nanowhiskers using different silica sources

    Institute of Scientific and Technical Information of China (English)

    Tao Yang; Peng-long Qiu; Mei Zhang; Kuo-Chih Chou; Xin-mei Hou; Bai-jun Yan

    2015-01-01

    Mullite nanowhiskers with Al-rich structure were prepared by molten salt synthesis at 1000°C for 3 h in air using silica, amor-phous silica, and ultrafine silica as the silica sources. The phase and morphology of the synthesized products were investigated by X-ray dif-fraction, scanning electron microscopy, energy dispersive spectroscopy, and transmission electron microscopy. A thermogravimetric and differential thermal analysis was carried out to determine the reaction mechanism. The results reveal that the silica sources play an important role in determining the morphology of the obtained mullite nanowhiskers. Clusters and disordered arrangements are obtained using common silica and amorphous silica, respectively, whereas the use of ultrafine silica leads to highly ordered mullite nanowhiskers that are 80−120 nm in diameter and 20−30μm in length. Considering the growth mechanisms, mullite nanowhiskers in the forms of clusters and highly ordered arrangements can be attributed to heterogeneous nucleation, whereas disordered mullite nanowhiskers are obtained by homogenous nuclea-tion.

  8. Molten Salt Promoting Effect in Double Salt CO2 Absorbents

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Keling; Li, Xiaohong S.; Chen, Haobo; Singh, Prabhakar; King, David L.

    2016-01-01

    The purpose of this paper is to elaborate on the concept of molten salts as catalysts for CO2 absorption by MgO, and extend these observations to the MgO-containing double salt oxides. We will show that the phenomena involved with CO2 absorption by MgO and MgO-based double salts are similar and general, but with some important differences. This paper focuses on the following key concepts: i) identification of conditions that favor or disfavor participation of isolated MgO during double salt absorption, and investigation of methods to increase the absorption capacity of double salt systems by including MgO participation; ii) examination of the relationship between CO2 uptake and melting point of the promoter salt, leading to the recognition of the role of pre-melting (surface melting) in these systems; and iii) extension of the reaction pathway model developed for the MgO-NaNO3 system to the double salt systems. This information advances our understanding of MgO-based CO2 absorption systems for application with pre-combustion gas streams.

  9. Optimized molten salt receivers for ultimate trough solar fields

    Science.gov (United States)

    Riffelmann, Klaus-J.; Richert, Timo; Kuckelkorn, Thomas

    2016-05-01

    Today parabolic trough collectors are the most successful concentrating solar power (CSP) technology. For the next development step new systems with increased operation temperature and new heat transfer fluids (HTF) are currently developed. Although the first power tower projects have successfully been realized, up to now there is no evidence of an all-dominant economic or technical advantage of power tower or parabolic trough. The development of parabolic trough technology towards higher performance and significant cost reduction have led to significant improvements in competitiveness. The use of molten salt instead of synthetic oil as heat transfer fluid will bring down the levelized costs of electricity (LCOE) even further while providing dispatchable energy with high capacity factors. FLABEG has developed the Ultimate TroughTM (UT) collector, jointly with sbp Sonne GmbH and supported by public funds. Due to its validated high optical accuracy, the collector is very suitable to operate efficiently at elevated temperatures up to 550 °C. SCHOTT will drive the key-innovations by introducing the 4th generation solar receiver that addresses the most significant performance and cost improvement measures. The new receivers have been completely redesigned to provide a product platform that is ready for high temperature operation up to 550 °C. Moreover distinct product features have been introduced to reduce costs and risks in solar field assembly and installation. The increased material and design challenges incurred with the high temperature operation have been reflected in sophisticated qualification and validation procedures.

  10. Decommissioning of the Molten Salt Reactor Experiment: A technical evaluation

    Energy Technology Data Exchange (ETDEWEB)

    Notz, K.J.

    1988-01-01

    This report completes a technical evaluation of decommissioning planning for the former Molten Salt Reactor Experiment, which was shut down in December, 1969. The key issues revolve around the treatment and disposal of some five tons of solid fuel salt which contains over 30 kg of fissionable uranium-233 plus fission products and higher actinides. The chemistry of this material is complicated by the formation of elemental fluorine via a radiolysis reaction under certain conditions. Supporting studies carried out as part of this evaluation include (a) a broad scope analysis of possible options for storage/disposal of the salts, (b) calculation of nuclide decay in future years, (c) technical evaluation of the containment facility and hot cell penetrations, (d) review and update of surveillance and maintenance procedures, (e) measurements of facility groundwater radioactivity and sump pump operation, (f) laboratory studies of the radiolysis reaction, and (g) laboratory studies which resulted in finding a suitable getter for elemental fluorine. In addition, geologic and hydrologic factors of the surrounding area were considered, and also the implications of entombment of the fuel in-place with concrete. The results of this evaluation show that the fuel salt cannot be left in its present form and location permanently. On the other hand, extended storage in its present form is quite acceptable for 20 to 30 years, or even longer. For continued storage in-place, some facility modifications are recommended. 30 refs., 5 figs., 9 tabs.

  11. Aerosol production by high-velocity molten-metal droplets

    Energy Technology Data Exchange (ETDEWEB)

    Rader, D J; Benson, D A

    1988-06-01

    This report presents the results of an experimental study of the aerosol produced by high-velocity molten-metal droplets. These tests are intended to simulate the reduction of high-velocity fragments into aerosol in high-explosive detonations or reactor accidents involving nuclear materials. The primary droplets are produced by the heating and electromagnetic launch of metal wires; velocities approaching Mach 1 can be obtained at present. Size distributions obtained tungsten and zirconium droplets burning in air. Lognormal size distributions were observed in both cases with DMPS-equivalent mean diameters of about 0.4 ..mu..m and geometric standard deviations of about two. SEM and TEM analysis of aerosol samples collected by a point-to-plane electrostatic precipitator showed that the majority of these particles were web-like chain agglomerates. Tests performed in argon atmospheres produced several orders-of-magnitude less aerosol mass than in equivalent air tests, supporting the key role combustion plays in secondary aerosol generation. 26 refs., 14 figs., 2 tabs.

  12. Electrochemistry of ytterbium (III) in molten alkali metal chlorides

    Energy Technology Data Exchange (ETDEWEB)

    Smolenski, V.; Novoselova, A. [Institute of High-Temperature Electrochemistry, Ural Division, Russian Academy of Science, Ekaterinburg, 620219 (Russian Federation); Osipenko, A. [Research Institute of Atomic Reactors, Dimitrovgrad-10, Ulyanovsk Region, 433010 (Russian Federation); Caravaca, C. [High Level Waste Unit, Nuclear Fission Division, CIEMAT, Madrid, 28040 (Spain); Cordoba, G. de [High Level Waste Unit, Nuclear Fission Division, CIEMAT, Madrid, 28040 (Spain)], E-mail: g.cordoba@ciemat.es

    2008-12-30

    This work presents the electrochemical study of Yb(III) ions in molten alkali metal chlorides in the temperature range 723-1073 K. Transient electrochemical techniques such as linear sweep, cyclic and square wave voltammetry, and potentiometry at zero current have been used to investigate the reduction mechanism, transport parameters and thermodynamic properties of the reaction YbCl{sub 2} + 1/2Cl{sub 2} = YbCl{sub 3} The results obtained show that the reduction reaction Yb(III) + e{sup -} {r_reversible} Yb(II) is reversible being controlled by the rate of the mass transfer. The diffusion coefficient of [YbCl{sub 6}]{sup 3-} complex ions has been determined at different temperatures in the fused eutectic LiCl-KCl, the equimolar NaCl-KCl and the CsCl media. The apparent standard potential of the soluble-soluble redox system Yb(III)/Yb(II) has been obtained by cyclic voltammetry. The influence of the nature of the solvent on the electrochemical and thermodynamic properties of ytterbium compounds is discussed.

  13. Explosive welding of a tube into a tube sheet

    Energy Technology Data Exchange (ETDEWEB)

    Green, Sheryll C. (London, OH); Linse, Vonne D. (Columbus, OH)

    1978-10-03

    A cartridge containing an explosive charge is placed within a tube assembled within a tube sheet. The charge is detonated through use of a detonator cord containing a minimum but effective amount of explosive material. The cord is contained inside a tubular shield throughout most of its length within the cartridge. A small length of the cord extends beyond the tubular shield to contact and detonate the explosive charge in its rear portion near the cartridge base. The cartridge base is provided of substantial mass and thickness in respect to side and front walls of the cartridge to minimize bulging beyond the rear face of the tube sheet. For remote activation an electrically activated detonator of higher charge density than the cord is attached to the cord at a location spaced from the tube sheet, cartridge and tube.

  14. Explosive welding of a tube into a tube sheet

    Energy Technology Data Exchange (ETDEWEB)

    Green, S.C.; Linse, V.D.

    1978-10-03

    A cartridge containing an explosive charge is placed within a tube assembled within a tube sheet. The charge is detonated through use of a detonator cord containing a minimum but effective amount of explosive material. The cord is contained inside a tubular shield throughout most of its length within the cartridge. A small length of the cord extends beyond the tublar shield to contact and detonate the explosive charge in its rear portion near the cartridge base. The cartridge base is provided of substantial mass and thickness in respect to side and front walls of the cartridge to minimize bulging beyond the rear face of the tube sheet. For remote activation an electrically activated detonator of higher charge density than the cord is attached to the cord at a location spaced from the tube sheet, cartridge and tube.

  15. Nasogastric tube syndrome induced by an indwelling long intestinal tube.

    Science.gov (United States)

    Sano, Naoki; Yamamoto, Masayoshi; Nagai, Kentaro; Yamada, Keiichi; Ohkohchi, Nobuhiro

    2016-04-21

    The nasogastric tube (NGT) has become a frequently used device to alleviate gastrointestinal symptoms. Nasogastric tube syndrome (NTS) is an uncommon but potentially life-threatening complication of an indwelling NGT. NTS is characterized by acute upper airway obstruction due to bilateral vocal cord paralysis. We report a case of a 76-year-old man with NTS, induced by an indwelling long intestinal tube. He was admitted to our hospital for treatment of sigmoid colon cancer. He underwent sigmoidectomy to release a bowel obstruction, and had a long intestinal tube inserted to decompress the intestinal tract. He presented acute dyspnea following prolonged intestinal intubation, and bronchoscopy showed bilateral vocal cord paralysis. The NGT was removed immediately, and tracheotomy was performed. The patient was finally discharged in a fully recovered state. NTS be considered in patients complaining of acute upper airway obstruction, not only with a NGT inserted but also with a long intestinal tube.

  16. Piezoelectric Rotary Tube Motor

    Science.gov (United States)

    Fisher, Charles D.; Badescu, Mircea; Braun, David F.; Culhane, Robert

    2011-01-01

    A custom rotary SQUIGGLE(Registered TradeMark) motor has been developed that sets new benchmarks for small motor size, high position resolution, and high torque without gear reduction. Its capabilities cannot be achieved with conventional electromagnetic motors. It consists of piezoelectric plates mounted on a square flexible tube. The plates are actuated via voltage waveforms 90 out of phase at the resonant frequency of the device to create rotary motion. The motors were incorporated into a two-axis postioner that was designed for fiber-fed spectroscopy for ground-based and space-based projects. The positioner enables large-scale celestial object surveys to take place in a practical amount of time.

  17. Primary Fallopian Tube Carcinoma

    Directory of Open Access Journals (Sweden)

    Prasad K Shetty

    2011-01-01

    Full Text Available Primary Fallopian Tube Carcinoma (PFTC is rare and accounts for about 0.3% of all gynecologic cancers. Less than 1500 cases have been reported in the literature. It arises in postmenopausal women and typically presents with abdominal pelvic pain, vaginal bleeding and watery discharge. However, a correct diagnosis is rarely achieved preoperative, and in many cases, the diagnosis is made after incidental surgery for unrelated conditions commonly being ovarian carcinoma . Compared with ovarian carcinoma, PFTC more often presents at early stages, but it has a worse prognosis. PFTC is usually managed in the same manner as ovarian cancer. We report a case of Left PFTC that presented as Left ovarian mass, and we briefly review the literature.

  18. Flaming on YouTube

    NARCIS (Netherlands)

    Moor, Peter J.; Heuvelman, A.; Verleur, R.

    2010-01-01

    In this explorative study, flaming on YouTube was studied using surveys of YouTube users. Flaming is defined as displaying hostility by insulting, swearing or using otherwise offensive language. Three general conclusions were drawn. First, although many users said that they themselves do not flame,

  19. Interpreting Shock Tube Ignition Data

    Science.gov (United States)

    2003-10-01

    times only for high concentrations (of order 1% fuel or greater). The requirements of engine (IC, HCCI , CI and SI) modelers also present a different...Paper 03F-61 Interpreting Shock Tube Ignition Data D. F. Davidson and R. K. Hanson Mechanical Engineering ... Engineering Department Stanford University, Stanford CA 94305 Abstract Chemical kinetic modelers make extensive use of shock tube ignition data

  20. Flaming on YouTube

    NARCIS (Netherlands)

    Moor, Peter J.; Heuvelman, Ard; Verleur, Ria

    2010-01-01

    In this explorative study, flaming on YouTube was studied using surveys of YouTube users. Flaming is defined as displaying hostility by insulting, swearing or using otherwise offensive language. Three general conclusions were drawn. First, although many users said that they themselves do not flame,

  1. 高温熔盐吸热器的传热研究和系统设计%The Study on the Heat Transfer of the Molten Salt Receiver and System Design

    Institute of Scientific and Technical Information of China (English)

    杨小平; 杨晓西; 丁静; 秦贯丰; 蒋润花

    2012-01-01

    The present study simulates the heat transfer performance of the molten salt receiver with non -uniform radiant heat flux, getting the inner tube wall temperature, heat transfer performance and other characteristic parameters. The results show that the temperature distribution of molten salt and tube wall are very uneven whether in axial or radial direction. The heat transfer coefficient is higher than that of the Sieder - Tate formula. The paper also designs and analyzes a solar thermal power tower with 10MW thermal capacity.%本文对非均匀辐射热流密度太阳能熔盐吸热器传热过程进行了模拟研究,得到了熔盐吸热器内部的温度、传热性能等特征参数.结果表明在轴向和径向上熔盐流体温度和管壁的温度都非常不均匀,同时其综合传热性能要高于按照Sieder-Tate公式的计算值.并对10MW塔式太阳能热发电的熔盐吸热器进行了设计和分析.

  2. Natural convection heat transfer characteristics of the molten metal pool with solidification by boiling coolant

    Energy Technology Data Exchange (ETDEWEB)

    Cho, Jae Seon; Suh, Kune Yull; Chung, Chang Hyun [Seoul National University, Seoul (Korea, Republic of); Paark, Rae Joon; Kim, Sang Baik [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

    1997-12-31

    This paper presents results of experimental studies on the heat transfer and solidification of the molten metal pool with overlying coolant with boiling. The metal pool is heated from the bottom surface and coolant is injected onto the molten metal pool. Ad a result, the crust, which is a solidified layer, may form at the top of the molten metal pool. Heat transfer is accomplished by a conjugate mechanism, which consists of the natural convection of the molten metal pool, the conduction in the crust layer and the convective boiling heat transfer in the coolant. This work examines the crust formation and the heat transfer rate on the molten metal pool with boiling coolant. The simulant molten pool material is tin (Sn) with the melting temperature of 232 deg C. Demineralized water is used as the working coolant. The crust layer thickness was ostensibly varied by the heated bottom surface temperature of the test section, but not much affected by the coolant injection rate. The correlation between the Nusselt number and the Rayleigh number in the molten metal pool region of this study is compared against the crust formation experiment without coolant boiling and the literature correlations. The present experimental results are higher than those from the experiment without coolant boiling, but show general agreement with the Eckert correlation, with some deviations in the high and low ends of the Rayleigh number. This discrepancy is currently attributed to concurrent rapid boiling of the coolant on top of the metal layer. 10 refs., 4 figs., 1 tab. (Author)

  3. Influence of submerged entry nozzle clogging on the behavior of molten steel in continuously cast slab molds

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    The influence of submerged entry nozzle clogging on the behavior of molten steel in continuously cast slab molds was studied using commercial code CFX4.3. The results indicate that clogging at the top part of the nozzle port not only increases the velocity of molten steel, but also enhances the wall shear stress, F number and heat flux. This clogging has the greatest effect on the behavior of molten steel. However, clogging at the top 1/3 of the nozzle only increases the velocity of molten steel and has little influence. Clogging at the bottom of the nozzle almost has no influence.

  4. Development of a cheap and accessible carbon fibers-in-poly(ether ether ketone) tube with high stability for online in-tube solid-phase microextraction.

    Science.gov (United States)

    Feng, Juanjuan; Sun, Min; Bu, Yanan; Luo, Chuannan

    2016-02-01

    Carbon fibers (CFs) are one kind of important industrial materials that can be obtained commercially at low price. Based on the high extraction efficiency of carbon sorbents, a cheap and accessible carbon fibers-in-poly(ether ether ketone) (PEEK) tube was developed for online in-tube solid-phase microextraction (SPME) method. Coupled to high performance liquid chromatography (HPLC), the CFs-in-tube SPME was applied to analyze eight polycyclic aromatic hydrocarbons (PAHs) in environmental aqueous samples. Extraction conditions (sampling rate, extraction time, methanol content) and desorption time were investigated for optimization of conditions. Under the optimum conditions, the CFs-in-tube SPME-HPLC method provided high extraction efficiency with enrichment factors up to 1748. Good linearity (0.05-50 μg L(-1), 0.5-50 μg L(-1)) and low detection limits (0.01-0.1 μg L(-1)) were also obtained. The online analysis method was finally applied to determine several model PAHs analytes in real environmental aqueous samples. Some target analytes were detected and relative recoveries were in the range of 92.3-111%. Due to natural chemical stability of carbon fibers and PEEK tube, the CFs-in-tube device exhibited high resistance to organic solvent, acid and alkaline conditions.

  5. Signs & Symptoms of Dextromethorphan Exposure from YouTube

    Science.gov (United States)

    Chary, Michael; Park, Emily H.; McKenzie, Andrew; Sun, Julia; Manini, Alex F.; Genes, Nicholas

    2014-01-01

    Detailed data on the recreational use of drugs are difficult to obtain through traditional means, especially for substances like Dextromethorphan (DXM) which are available over-the-counter for medicinal purposes. In this study, we show that information provided by commenters on YouTube is useful for uncovering the toxicologic effects of DXM. Using methods of computational linguistics, we were able to recreate many of the clinically described signs and symptoms of DXM ingestion at various doses, using information extracted from YouTube comments. Our study shows how social networks can enhance our understanding of recreational drug effects. PMID:24533044

  6. Signs & symptoms of Dextromethorphan exposure from YouTube.

    Directory of Open Access Journals (Sweden)

    Michael Chary

    Full Text Available Detailed data on the recreational use of drugs are difficult to obtain through traditional means, especially for substances like Dextromethorphan (DXM which are available over-the-counter for medicinal purposes. In this study, we show that information provided by commenters on YouTube is useful for uncovering the toxicologic effects of DXM. Using methods of computational linguistics, we were able to recreate many of the clinically described signs and symptoms of DXM ingestion at various doses, using information extracted from YouTube comments. Our study shows how social networks can enhance our understanding of recreational drug effects.

  7. Water-storage-tube systems. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Hemker, P.

    1981-12-24

    Passive solar collection/storage/distribution systems were surveyed, designed, fabricated, and mechanically and thermally tested. The types studied were clear and opaque fiberglass tubes, metal tubes with plastic liners, and thermosyphoning tubes. (MHR)

  8. Vidicon storage tube electrical input/output

    Science.gov (United States)

    Lipoma, P.

    1972-01-01

    Electrical data storage tube is assembled from standard vidicon tube using conventional amplification and control circuits. Vidicon storage tube is simple, inexpensive and has an erase and preparation time of less than 5 microseconds.

  9. Chemical and Electrochemical Processing of Aluminum Dross Using Molten Salts

    Science.gov (United States)

    Yan, Xiao Y.

    2008-04-01

    A novel molten salt process was investigated, where Al, as metal or contained in Al2O3 and AlN, was recovered from Al dross by chemical or direct electrochemical reduction in electrolytic cells. Electrolysis experiments were carried out under argon at temperatures from 1123 to 1243 K. In order to better understand the reduction behavior, the as-received Al dross was simulated using simplified systems, including pure Al2O3, pure AlN, an Al2O3/AlN binary mixture, and an Al2O3/AlN/Al ternary mixture. The reduction of the as-received dross was also studied experimentally. The studies showed that solid Al2O3 was chemically reduced by the Ca in a Ca-saturated Ca-CaCl2 melt to form Al2Ca or electrochemically reduced to Al-rich Al-Ca alloys and that the Al value in the Al2O3 was easily recovered from the Al drosses. It was found experimentally that solid AlN in the drosses could not be calciothermically reduced to any extent, consistent with thermodynamic evaluations. It was also found that the direct electrochemical reduction of the AlN in the drosses was confined to three phase boundaries (3PBs) between the AlN, the electrolyte, and the current collector and could not be enhanced by using the LiCl-containing chloride melt or the chloride-fluoride melts studied. The presence of Al powder in the Al2O3/AlN mixture facilitated the direct electrochemical reduction of both Al2O3 and AlN. The reduction mechanisms are discussed based upon the present experimental observations. Flow sheets for recovering the metallic Al and the Al in the Al2O3 and AlN from Al dross are finally proposed.

  10. Dodonaea viscosa var. angustifolia Inhibits Germ Tube and Biofilm Formation by C. albicans

    Directory of Open Access Journals (Sweden)

    Serisha Devi Naicker

    2013-01-01

    Full Text Available The virulence factors of Candida albicans are germ tube and biofilm formation, adherence to host tissues, and production of hydrolytic enzymes. This study investigated the effect of Dodonaea viscosa var. angustifolia extract on the germ tube and biofilm formation of C. albicans. Serum containing the three subinhibitory concentrations of leaf extract was inoculated with C. albicans, incubated, and viewed under a light microscope. Number of cells with germ tube was recorded and the results were analysed using Scheffe test for pairwise comparison. Biofilms were grown on coverslips in the presence of plant extracts and processed for scanning electron microscopy (SEM. Planktonic cells were grown in the presence of plant extract for 6 h and processed for electron microscopy (TEM. The crude plant extract significantly (P<0.01 reduced the germ tube formation of C. albicans at 3.125 (85.36%, 1.56 (61.91%, and 0.78 mg/mL (26.27% showing a concentration dependent effect. SEM results showed concentration dependent reduction in biofilm and hyphae formation. TEM results showed that the plant extract caused damage to the cell wall and cell membrane. DVA extract has ability to reduce virulence of C. albicans by inhibiting germ tube and biofilm formation through damage to the cell wall. Therefore, it has therapeutic potential.

  11. Carbon particle induced foaming of molten sucrose for the preparation of carbon foams

    Energy Technology Data Exchange (ETDEWEB)

    Narasimman, R.; Vijayan, Sujith; Prabhakaran, K., E-mail: kp2952002@gmail.com

    2014-11-15

    Graphical abstract: - Highlights: • An easy method for the preparation of carbon foam from sucrose is presented. • Wood derived activated carbon particles are used to stabilize the molten sucrose foam. • The carbon foams show relatively good mechanical strength. • The carbon foams show excellent CO{sub 2} adsorption and oil absorption properties. • The process could be scaled up for the preparation of large foam bodies. - Abstract: Activated carbon powder was used as a foaming and foam setting agent for the preparation of carbon foams with a hierarchical pore structure from molten sucrose. The rheological measurements revealed the interruption of intermolecular hydrogen bonding in molten sucrose by the carbon particles. The carbon particles stabilized the bubbles in molten sucrose by adsorbing on the molten sucrose–gas interface. The carbon foams obtained at the activated carbon powder to sucrose weight ratios in the range of 0–0.25 had a compressive strength in the range of 1.35–0.31 MPa. The produced carbon foams adsorb 2.59–3.04 mmol/g of CO{sub 2} at 760 mmHg at 273 K and absorb oil from oil–water mixtures and surfactant stabilized oil-in-water emulsions with very good selectivity and recyclability.

  12. Space Molten Salt Reactor Concept for Nuclear Electric Propulsion and Surface Power

    Science.gov (United States)

    Eades, M.; Flanders, J.; McMurray, N.; Denning, R.; Sun, X.; Windl, W.; Blue, T.

    Students at The Ohio State University working under the NASA Steckler Grant sought to investigate how molten salt reactors with fissile material dissolved in a liquid fuel medium can be applied to space applications. Molten salt reactors of this kind, built for non-space applications, have demonstrated high power densities, high temperature operation without pressurization, high fuel burn up and other characteristics that are ideal for space fission systems. However, little research has been published on the application of molten salt reactor technology to space fission systems. This paper presents a conceptual design of the Space Molten Salt Reactor (SMSR), which utilizes molten salt reactor technology for Nuclear Electric Propulsion (NEP) and surface power at the 100 kWe to 15 MWe level. Central to the SMSR design is a liquid mixture of LiF, BeF2 and highly enriched U235F4 that acts as both fuel and core coolant. In brief, some of the positive characteristics of the SMSR are compact size, simplified core design, high fuel burn up percentages, proliferation resistant features, passive safety mechanisms, a considerable body of previous research, and the possibility for flexible mission architecture.

  13. Integrated oil production and upgrading using molten alkali metal

    Energy Technology Data Exchange (ETDEWEB)

    Gordon, John Howard

    2016-10-04

    A method that combines the oil retorting process (or other process needed to obtain/extract heavy oil or bitumen) with the process for upgrading these materials using sodium or other alkali metals. Specifically, the shale gas or other gases that are obtained from the retorting/extraction process may be introduced into the upgrading reactor and used to upgrade the oil feedstock. Also, the solid materials obtained from the reactor may be used as a fuel source, thereby providing the heat necessary for the retorting/extraction process. Other forms of integration are also disclosed.

  14. Integrated oil production and upgrading using molten alkali metal

    Science.gov (United States)

    Gordon, John Howard

    2016-10-04

    A method that combines the oil retorting process (or other process needed to obtain/extract heavy oil or bitumen) with the process for upgrading these materials using sodium or other alkali metals. Specifically, the shale gas or other gases that are obtained from the retorting/extraction process may be introduced into the upgrading reactor and used to upgrade the oil feedstock. Also, the solid materials obtained from the reactor may be used as a fuel source, thereby providing the heat necessary for the retorting/extraction process. Other forms of integration are also disclosed.

  15. Acoustical studies on corrugated tubes

    Science.gov (United States)

    Balaguru, Rajavel

    Corrugated tubes and pipes offer greater global flexibility combined with local rigidity. They are used in numerous engineering applications such as vacuum cleaner hosing, air conditioning systems of aircraft and automobiles, HVAC control systems of heating ducts in buildings, compact heat exchangers, medical equipment and offshore gas and oil transportation flexible riser pipelines. Recently there has been a renewed research interest in analyzing the flow through a corrugated tube to understand the underlying mechanism of so called whistling, although the whistling in such a tube was identified in early twentieth century. The phenomenon of whistling in a corrugated tube is interesting because an airflow through a smooth walled tube of similar dimensions will not generate any whistling tones. Study of whistling in corrugated tubes is important because, it not only causes an undesirable noise problem but also results in flow-acoustic coupling. Such a coupling can cause significant structural vibrations due to flow-acoustic-structure interaction. This interaction would cause flow-induced vibrations that could result in severe damage to mechanical systems having corrugated tubes. In this research work, sound generation (whistling) in corrugated tubes due to airflow is analyzed using experimental as well as Computational Fluid Dynamics-Large Eddy Simulation (CFD-LES) techniques. Sound generation mechanisms resulting in whistling have been investigated. The whistling in terms of frequencies and sound pressure levels for different flow velocities are studied. The analytical and experimental studies are carried out to understand the influence of various parameters of corrugated tubes such as cavity length, cavity width, cavity depth, pitch, Reynolds numbers and number of corrugations. The results indicate that there is a good agreement between theoretically calculated, computationally predicted and experimentally measured whistling frequencies and sound pressure levels

  16. Electronic components, tubes and transistors

    CERN Document Server

    Dummer, G W A

    1965-01-01

    Electronic Components, Tubes and Transistors aims to bridge the gap between the basic measurement theory of resistance, capacitance, and inductance and the practical application of electronic components in equipments. The more practical or usage aspect of electron tubes and semiconductors is given emphasis over theory. The essential characteristics of each main type of component, tube, and transistor are summarized. This book is comprised of six chapters and begins with a discussion on the essential characteristics in terms of the parameters usually required in choosing a resistor, including s

  17. PEG tubes: dealing with complications.

    Science.gov (United States)

    Malhi, Hardip; Thompson, Rosie

    A percutaneous endoscopic gastronomy tube can be used to deliver nutrition, hydration and medicines directly into the patient's stomach. Patients will require a tube if they are unable to swallow safely, putting them at risk of aspiration of food, drink and medicines into their lungs. It is vital that nurses are aware of the complications that may arise when caring for a patient with a PEG tube. It is equally important that nurses know how to deal with these complications or from where tc seek advice. This article provides a quick troubleshooting guide to help nurses deal with complications that can arise with PEG feeding.

  18. Molten Salt Heat Transport Loop: Materials Corrosion and Heat Transfer Phenomena

    Energy Technology Data Exchange (ETDEWEB)

    Dr. Kumar Sridharan; Dr. Mark Anderson; Dr. Michael Corradini; Dr. Todd Allen; Luke Olson; James Ambrosek; Daniel Ludwig

    2008-07-09

    An experimental system for corrosion testing of candidate materials in molten FLiNaK salt at 850 degree C has been designed and constructed. While molten FLiNaK salt was the focus of this study, the system can be utilized for evaluation of materials in other molten salts that may be of interest in the future. Using this system, the corrosion performance of a number of code-certified alloys of interest to NGNP as well as the efficacy of Ni-electroplating have been investigated. The mechanisums underlying corrosion processes have been elucidated using scanning electron microscopy, x-ray diffraction, and x-ray photoelectron spectroscopy of the materials after the corrosion tests, as well as by the post-corrosion analysis of the salts using inductively coupled plasma (ICP) and neutron activation analysis (NAA) techniques.

  19. Molten metal-related ocular thermal burn: report on two cases

    Directory of Open Access Journals (Sweden)

    Ceyhun Arici

    2015-12-01

    Full Text Available ABSTRACT We report two cases of severe thermal burns on the ocular surface and its adnexal appendages that developed secondary to exposure to molten heavy metal with a melting temperature of near-thousand degree Celsius. Despite aggressive intervention and strict monitoring, the profound inflammation caused significant damage to the ocular surface, ending up in an intractable infection with an unfavorable outcome. The heat of the molten metal at impact, the heat-retaining capacity of the heavy metal, the total area of the ocular surface exposed to the molten metal, and the duration of exposure determined the severity of the injury. The unfavorable outcome, despite an intensive treatment, in terms of visual acuity and cosmetic appearance, should be explicitly explained to the patient, and a psychiatrist consultation should be considered if necessary.

  20. A Novel Electrochemical Oxygen Sensor for Determination of Ultra-low Oxygen Contents in Molten Metal

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    A novel electrochemical oxygen sensor has been developed by using La-Al2O3 as solid electrolyte and Cr+Cr2O3 as reference electrode. The sensor not only can be used as normal oxygen sensor but also as an ultra-low oxygen sensor. Especially, it is very sensitive to measure ultra-low oxygen in molten metal. For estimating the accuracy of La-Al2O3 oxygen sensor, two series of oxygen activities in molten iron at different oxygen contents and different temperature were measured by both La-Al2O3 oxygen sensor and ZrO2 oxygen sensor. The theoretical values of oxygen activities in molten iron (3.30%C, in mass fraction) at 1723K and 1745K were also evaluated for comparing the measuring results of two sensors. At last, the error of measurement for La-Al2O3 oxygen sensor was discussed too.

  1. A new dynamic method for measuring hydrogen partial pressure in molten aluminum alloy

    Directory of Open Access Journals (Sweden)

    Sun Qian

    2011-02-01

    Full Text Available Hydrogen partial pressure is an important parameter to calculate hydrogen concentration levels in molten aluminum alloy. A new dynamic method for measuring hydrogen partial pressure in molten aluminum alloy is studied. Dynamic and rapid measurement is realized through changing the volume of the vacuum chamber and calculating the pressure difference ΔP between the theoretical and measured pressures in the vacuum chamber. Positive ΔP indicates hydrogen transmits from melt to vacuum chamber and negative ΔP means the reverse. When ΔP is equal to zero, hydrogen transmitted from both sides reached a state of dynamical equilibrium and the pressure in the vacuum chamber is equal to the hydrogen partial pressure in the molten aluminum alloy. Compared with other existing measuring methods, the new method can significantly shorten the testing time and reduce measuring cost.

  2. Vacuum Treatment for Simultaneous Desulphurization and Dephosphorization of Hot Metal and Molten Steel

    Institute of Scientific and Technical Information of China (English)

    WANG Hai-chuan; WANG Shi-jun; ZHOU Yun; WU Bao-guo; DONG Yuan-chi

    2004-01-01

    The vacuum treatment for simultaneous desulphurization and dephosphorization of hot metal and molten steel with pre-melted CaO-based slag was carried out. For pre-treatment of hot metal, both desulphurization and dephosphorization are improved with the increase of CaO in slag, but deteriorated with the increase of CaF2 in slag. The average desulphurization and dephosphorization rate is 68.83 % and 78.46 %, respectively. For molten steel, the substitution of BaO for CaO in slag has minor effect on simultaneous desulphurization and dephosphorization. The desulphurization and dephosphorization rate is higher than 90 % and 50 % respectively with the lowest final sulfur and phosphorus mass percent being 0.001 2 % and 0.010 %, respectively. The overall effect of simultaneous desulphurization and dephosphorization of molten steel is better than that of hot metal.

  3. Production of Low-Phosphorus Molten Iron from High-Phosphorus Oolitic Hematite Using Biomass Char

    Science.gov (United States)

    Tang, Huiqing; Qi, Tengfei; Qin, Yanqi

    2015-09-01

    In this study, an energy-saving and environmentally friendly method to produce low-phosphorus molten iron from high-phosphorus oolitic hematite was experimentally investigated and theoretically analyzed. The results indicate that biomass char is a suitable reducing agent for the proposed method. In the direct reduction stage, the ore-char briquette reached a metallization degree of 80-82% and a residual carbon content of 0.1-0.3 mass%. Under the optimized condition, phosphorus remained in the gangue as calcium phosphate. In the melting separation stage, phosphorus content ([%P]) in molten iron could be controlled by introducing a Na2CO3 additive, and the phosphorus behavior could be predicted using ion molecular coexistence theory. Molten iron with [%P] less than 0.3 mass% was obtained from the metallic briquettes with the aforementioned quality by introducing 2-4% Na2CO3 and the iron recovery rate was 75-78%.

  4. Very Efficient Nucleophilic Aromatic Fluorination Reaction in Molten Salts: A Mechanistic Study

    Energy Technology Data Exchange (ETDEWEB)

    Jang, Sung Woo; Park, Sung Woo; Lee, Sung Yul [Kyung Hee University, Seoul (Korea, Republic of); Lee, Byoung Se; Chi, Dae Yoon [Sogang University, Seoul (Korea, Republic of); Song, Choong Eui [Sungkyunkwan University, Suwon (Korea, Republic of)

    2012-03-15

    We report a quantum chemical study of an extremely efficient nucleophilic aromatic fluorination in molten salts. We describe that the mechanism involves solvent anion interacting with the ion pair nucleophile M{sup +}F{sup -} (M = Na, K, Rb, Cs) to accelerate the reaction. We show that our proposed mechanism may well explain the excellent efficiency of molten salts for S{sub N}Ar reactions, the relative efficacy of the metal cations, and also the observed large difference in rate constants in two molten salts (n-C{sub 4}H{sub 9}){sub 4}N{sup +} CX{sub 3}SO{sub 3}{sup -}, (X=H, F) with slightly different sidechain (-CH{sub 3} vs. -CF{sub 3})

  5. A Feasibility Study of Steelmaking by Molten Oxide Electrolysis (TRP9956)

    Energy Technology Data Exchange (ETDEWEB)

    Donald R. Sadoway; Gerbrand Ceder

    2009-12-31

    Molten oxide electrolysis (MOE) is an extreme form of molten salt electrolysis, a technology that has been used to produce tonnage metals for over 100 years - aluminum, magnesium, lithium, sodium and the rare earth metals specifically. The use of carbon-free anodes is the distinguishing factor in MOE compared to other molten salt electrolysis techniques. MOE is totally carbon-free and produces no CO or CO2 - only O2 gas at the anode. This project is directed at assessing the technical feasibility of MOE at the bench scale while determining optimum values of MOE operating parameters. An inert anode will be identified and its ability to sustain oxygen evalution will be demonstrated.

  6. Advances in Molten Oxide Electrolysis for the Production of Oxygen and Metals from Lunar Regolith

    Science.gov (United States)

    Sadoway, Donald R.; Sirk, Aislinn; Sibille, Laurent; Melendez, Orlando; Lueck, Dale; Curreri, Peter; Dominquez, Jesus; Whitlow, Jonathan

    2008-01-01

    As part of an In-Situ Resource Utilization infrastructure to sustain long term-human presence on the lunar surface, the production of oxygen and metals by electrolysis of lunar regolith has been the subject of major scrutiny. There is a reasonably large body of literature characterizing the candidate solvent electrolytes, including ionic liquids, molten salts, fluxed oxides, and pure molten regolith itself. In the light of this information and in consideration of available electrolytic technologies, the authors have determined that direct molten oxide electrolysis at temperatures of approx 1600 C is the most promising avenue for further development. Results from ongoing studies as well as those of previous workers will be presented. Topics include materials selection and testing, electrode stability, gas capture and analysis, and cell operation during feeding and tapping.

  7. Polygenic expression of teratozoospermia and normal fertility in B10.MOL-TEN1 mouse strain.

    Science.gov (United States)

    Hirawatari, Keitaro; Hanzawa, Naoto; Kuwahara, Maki; Aoyama, Hiroaki; Miura, Ikuo; Wakana, Shigeharu; Gotoh, Hideo

    2015-05-01

    Subfertility and infertility are two major reproductive health problems in human and domestic animals. The contribution of the genotype to these conditions is poorly understood. To examine the genetic basis of male subfertility, we analyzed its relationship to sperm morphology in B10.MOL-TEN1 mice, which shows high-frequencies (about 50%) of morphologically abnormal sperm. Drastic histological changes were also found in the testis of the B10.MOL-TEN1. Segregation analysis showed that the abnormal sperm phenotype in B10.MOL-TEN1 was inherited and was predictably controlled by at least three loci. We also found that male fertility of this strain was normal. These findings indicate a complicated relationship between sperm morphology and male subfertility.

  8. STUDY ON EROSION RESISTANCE PROPERTIES OF O'-SIALON-BN IN MOLTEN STEEL

    Institute of Scientific and Technical Information of China (English)

    Q. Zhen; W.Z. Ding; W.C. Li

    2001-01-01

    The erosion resistance properties of O'-Sialon-BN in molten steel are investigated in this work. According to experimental results and theoretical analysis, BN in O'Sialon-BN plays an important role in molten steel erosion resistance. And the erosion kinetics of the O'-Sialon-BN composites in molten steel is controlled by two stages:the first one is controlled by chemical reaction taking place on the interface; the second one is controlled by diffusion. The erosion surface of the materials is also investigated with fractal theory. The results show that the fractal dimensions of the erosion surface vary with erosion time from a linear way to parabolic way, which relates to the change of erosion mechanism from interface chemical reaction to diffusion.

  9. Optimization and simplification of the concept of non-moderated Thorium Molten Salt Reactor

    Energy Technology Data Exchange (ETDEWEB)

    Merle-Lucotte, Elsa; Heuer, Daniel; Allibert, Michel; Doligez, Xavier; Ghetta, Veronique; Le Brun, Christian [LPSC-IN2P3-CNRS/UJF/INPG, LPSC 53 avenue des Martyrs, 38026 Grenoble Cedex (France)

    2008-07-01

    Molten salt reactors, in the configuration presented here and called Thorium Molten Salt Reactor (TMSR), are particularly well suited to fulfil the criteria defined by the Generation IV forum, and may be operated in simplified and safe conditions in the Th/{sup 233}U fuel cycle with fluoride salts. The characteristics of the non-moderated TMSR based on a fast neutron spectrum are detailed in this paper: we aimed at designing an optimised TMSR with the simplest configuration. Using a simple kinetic-point model, we analyze the reactor's transient as the total reactivity margins are introduced in the core. We thus confirm, beyond the classical advantages of molten salt reactors, the satisfactory behaviour of the TMSR in terms of safety and the excellent level of stability which can be achieved in such reactors. (authors)

  10. Improving Corrosion Resistance of Ferrous Alloy to Molten Zn by Modifying the Laves Phase Characteristics

    Science.gov (United States)

    Liu, X.; Yin, F. C.; Lou, J.; Ouyang, X. M.; Li, Z.

    2017-08-01

    The Laves phase morphology in the Fe25Mo14Cr10Ni1Si (wt.%) alloy was modified by Si addition to improve the corrosion resistance of the ferrous alloy to molten zinc. The Si-containing alloy showed a woven, needle-like Laves phase with higher Mo content than that of the Fe25Mo14Cr10Ni alloy. Corrosion resistance to molten Zn for the Si-containing alloy was more than 20 times higher than that of the silicon-free alloy mainly as a result of the characteristics of the modified Laves phase. This phase was oriented perpendicular to the Zn-diffusion direction, which effectively prevented corrosion by the molten Zn, leading to a denser FeZn13 layer rather than the FeZn10 layer produced in the Fe25Mo14Cr10Ni alloy.

  11. Complex Behavior of Forces Influencing Molten Weld Metal Flow based on Static Force Balance Theory

    Science.gov (United States)

    Achebo, Joseph I.

    This study is aimed at investigating the forces responsible for the detachment of molten metal droplets formed at an electrode tip, which imminently and eventually drop into the weld pool during the welding process. The Equations used by Kim and Eagar in 1993 were applied to this study. It was found that the different detaching forces which are the gravitational force, the electromagnetic force, and the drag force, were determined to be 7.154 x 10-6N, 0.05N and 1.736N respectively. Whereas, the primary retaining force, which is the surface tension force, was calculated to be 0.0195N. From the findings, since the combination of the detaching forces taken together is greater than the retaining force, detachment of the molten metal droplet must inevitably occur. The combined effect of these forces on the behaviour of molten metal during the droplet detachment process was adequately investigated in this study.

  12. Preparation of Ferrotitanium Alloy from Ilmenite by Electrochemical Reduction in Chloride Molten Salts

    Science.gov (United States)

    Qi, Can-can; Hua, Yi-xin; Chen, Kong-hao; Jie, Ya-fei; Zhou, Zhong-ren; Ru, Juan-jian; Xiong, Li; Gong, Kai

    2016-02-01

    Ferrotitanium alloy is prepared by electrochemical reduction from ilmenite in LiCl-KCl and LiCl-KCl-CaCl2 molten salts, respectively. The products prepared are observed by x-ray diffraction (XRD). It is shown that Fe2Ti can be prepared from ilmenite in LiCl-KCl molten salt at 1073 K with a cell voltage of 3.2 V. Ilmenite can be electrochemically reduced to FeTi in LiCl-KCl-CaCl2 molten salt under the same condition. It is indicated that CaCl2 can promote the reaction and is favors the deoxidization of the FeTiO3.

  13. Activities of chromium in molten copper at dilute concentrations by solid-state electrochemical cell

    Science.gov (United States)

    Inouye, T. K.; Fujiwara, H.; Iwase, M.

    1991-08-01

    In order to obtain the activities of chromium in molten copper at dilute concentrations (copper was brought to equilibrium with molten CaCl2 + Cr2O3 slag saturated with Cr2O3 (s), at temperatures between 1423 and 1573 K, and the equilibrium oxygen partial pressures were measured by means of solid-oxide galvanic cells of the type Mo/Mo + MoO2/ZrO2(MgO)/(Cu + Cr))alloy + Cr2O3 + (CaCl2 + Cr2O3)slag/Mo. The free energy changes for the dissolution of solid chromium in molten copper at infinite dilution referred to 1 wt pct were determined as Cr (s) = Cr(1 wt pct, in Cu) and Δ G° = + 97,000 + 73.3 (T/K) ± 2,000 J mol-1.

  14. Prediction of the thermophysical properties of molten salt fast reactor fuel from first-principles

    Science.gov (United States)

    Gheribi, A. E.; Corradini, D.; Dewan, L.; Chartrand, P.; Simon, C.; Madden, P. A.; Salanne, M.

    2014-05-01

    Molten fluorides are known to show favourable thermophysical properties which make them good candidate coolants for nuclear fission reactors. Here we investigate the special case of mixtures of lithium fluoride and thorium fluoride, which act both as coolant and as fuel in the molten salt fast reactor concept. By using ab initio parameterised polarisable force fields, we show that it is possible to calculate the whole set of properties (density, thermal expansion, heat capacity, viscosity and thermal conductivity) which are necessary for assessing the heat transfer performance of the melt over the whole range of compositions and temperatures. We then deduce from our calculations several figures of merit which are important in helping the optimisation of the design of molten salt fast reactors.

  15. Induction furnace testing of the durability of prototype crucibles in a molten metal environment

    Energy Technology Data Exchange (ETDEWEB)

    Jablonski, Paul D.

    2005-09-01

    Engineered ceramic crucibles are commonly used to contain molten metal. Besides high temperature stability, other desired crucible characteristics include thermal shock resistance, minimal reaction with the molten metal and resistance to attack from the base metal oxide formed during melting. When used in an induction furnace, they can be employed as a “semi-permanent” crucible incorporating a dry ram backup and a ceramic cap. This report covers several 250-lb single melt crucible tests in an air melt induction furnace. These tests consisted of melting a charge of 17-4PH stainless steel, holding the charge molten for two hours before pouring off the heat and then subsequently sectioning the crucible to review the extent of erosion, penetration and other physical characteristics. Selected temperature readings were made throughout each melt. Chemistry samples were also taken from each heat periodically throughout the hold. The manganese level was observed to affect the rate of chromium loss in a non-linear fashion.

  16. Numerical simulation and experimental investigation of natural convection heat transfer of molten salt around fine wire

    Institute of Scientific and Technical Information of China (English)

    LU; YuanWei; LI; XiaoLi; LI; Qiang; WU; YuTing; MA; ChongFang

    2013-01-01

    In order to get the natural convection heat transfer mechanism of molten salt, the experimental investigation of natural convective heat transfer of LiNO3was studied after it was simulated by numerical calculation. Experiment was carried out on the nat-ural convection heat transfer of air and water around the fine wire using the method of Joule heating. The results showed that the natural convection heat transfer of air and water around the fine wire agreed well with Fand’s correlation. Based on the aforementioned experiment, the natural convection heat transfer of molten salt LiNO3was studied by experiment and the same results were got. Therefore, the natural convection heat transfer of molten salt can be calculated by Fand’s correlation, which takes into consideration the effect of viscosity dissipation.

  17. Electrochemical Impedance and Modelling Studies of the Corrosion of Three Commercial Stainless Steels in Molten Carbonate

    Directory of Open Access Journals (Sweden)

    C. S. Ni

    2014-01-01

    Full Text Available The corrosion induced by molten carbonates on the metallic structure materials is a problem constraining the life span of molten carbonate fuel cell (MCFC at elevated temperatures. The reaction between the outgrowing oxide scale and lithium carbonate in the electrolyte is generally a slow process and very important to the passivation behaviour of the underlying steel. The corrosion behaviour of three commercial alloys (P92, SS304, and SS310 with different Cr contents in molten (0.62Li, 0.38K2CO3 at 650°C was monitored by electrochemical impedance spectroscopy (EIS for 120 hours to investigate the lithiation process. With SEM images and extensive XRD analysis of the oxides, equivalent circuits were proposed to interpret the impedance data and explain the corrosion behaviour of the three alloys at different stage with respect to lithiation process.

  18. NEI You Tube Videos: Amblyopia

    Medline Plus

    Full Text Available ... questions Clinical Studies Publications Catalog Photos and Images Spanish Language Information Dilated Exam Grants and Funding Extramural ... Low Vision Refractive Errors Retinopathy of Prematurity Science Spanish Videos Webinars NEI YouTube Videos: Amblyopia Embedded video ...

  19. Tube-wave seismic imaging

    Science.gov (United States)

    Korneev, Valeri A [LaFayette, CA

    2009-05-05

    The detailed analysis of cross well seismic data for a gas reservoir in Texas revealed two newly detected seismic wave effects, recorded approximately 2000 feet above the reservoir. A tube-wave (150) is initiated in a source well (110) by a source (111), travels in the source well (110), is coupled to a geological feature (140), propagates (151) through the geological feature (140), is coupled back to a tube-wave (152) at a receiver well (120), and is and received by receiver(s) (121) in either the same (110) or a different receiving well (120). The tube-wave has been shown to be extremely sensitive to changes in reservoir characteristics. Tube-waves appear to couple most effectively to reservoirs where the well casing is perforated, allowing direct fluid contact from the interior of a well case to the reservoir.

  20. NEI You Tube Videos: Amblyopia

    Medline Plus

    Full Text Available ... questions Clinical Studies Publications Catalog Photos and Images Spanish Language Information Grants and Funding Extramural Research Division ... Low Vision Refractive Errors Retinopathy of Prematurity Science Spanish Videos Webinars NEI YouTube Videos: Amblyopia Embedded video ...