Corrosión atmosférica del zinc en ambientes exteriores e interiores

Directory of Open Access Journals (Sweden)

Castaño, J. G.

2007-04-01

Full Text Available Good behaviour of zinc against atmospheric corrosion has leaded this material to be widely used, mainly for protection of steel. For this reason since approximately 50 years it have been making systematic studies in order to understand the mechanisms of its interaction with the atmosphere and nowadays it continues being object of intensive research. In this paper a review of the state-of-the-art in the knowledge of atmospheric corrosion of zinc is presented, when it is exposed in both outdoor and indoor atmospheres.

El buen comportamiento del zinc frente a la corrosión atmosférica ha conducido a que este material sea utilizado ampliamente, sobre todo, como recubrimiento del acero. Por este motivo, desde hace unos 50 años, se han venido realizando estudios sistemáticos para tratar de comprender los mecanismos de su interacción con la atmósfera y, hoy en día, el tema sigue siendo objeto de intensa investigación. En este artículo se presenta una revisión de los aspectos fundamentales relacionados con el conocimiento acumulado, en este tiempo, sobre el fenómeno de la corrosión atmosférica del zinc, expuesto tanto en ambientes exteriores como en interiores.

Astrophysically Satisfactory Solutions to Einstein's R-33 Gravitational Field Equations Exterior/Interior to Static Homogeneous Oblate Spheroidal Masses

Directory of Open Access Journals (Sweden)

Chifu E. N.

2009-10-01

Full Text Available In this article, we formulate solutions to Einstein's geometrical field equations derived using our new approach. Our field equations exterior and interior to the mass distribution have only one unknown function determined by the mass or pressure distribution. Our obtained solutions yield the unknown function as generalizations of Newton's gravitational scalar potential. Thus, our solution puts Einstein's geometrical theory of gravity on same footing with Newton's dynamical theory; with the dependence of the field on one and only one unknown function comparable to Newton's gravitational scalar potential. Our results in this article are of much significance as the Sun and planets in the solar system are known to be more precisely oblate spheroidal in geometry. The oblate spheroidal geometries of these bodies have effects on their gravitational fields and the motions of test particles and photons in these fields.

Numerical conformal mapping methods for exterior and doubly connected regions

Energy Technology Data Exchange (ETDEWEB)

DeLillo, T.K. [Wichita State Univ., KS (United States); Pfaltzgraff, J.A. [Univ. of North Carolina, Chapel Hill, NC (United States)

1996-12-31

Methods are presented and analyzed for approximating the conformal map from the exterior of the disk to the exterior a smooth, simple closed curve and from an annulus to a bounded, doubly connected region with smooth boundaries. The methods are Newton-like methods for computing the boundary correspondences and conformal moduli similar to Fornberg`s method for the interior of the disk. We show that the linear systems are discretizations of the identity plus a compact operator and, hence, that the conjugate gradient method converges superlinearly.

BWR fuel assembly having fuel rod spacers axially positioned by exterior springs

International Nuclear Information System (INIS)

Taleyarkhan, R.P.

1988-01-01

In a fuel assembly having spaced fuel rods, an outer hollow tubular flow channel surrounding the fuel rods so as to direct flow of coolant/moderator fluid there-along, and at least one spacer being disposed along the channel and about the fuel rods so as to maintain them in side-by-side spaced relationship, an arrangement for disposing the spacer in a desired axial position along the fuel rods is described comprising: yieldably resilient springs disposed between an interior side of the outer channel and an exterior side of the spacer. The springs have an inherent spring bias directed away from the exterior sides of the spacers and toward the interior side of the channel such that by contact with the channel and spacer the springs assume states in which they are deflected away from the channel interior side so as to exert sufficient compressive contacting force thereon to maintain the spacer substantially stationary in the desired axial position along the fuel rods

Evaluation of the natural radioactivity in the gamma range by means of a manual dosimeter in the interior and external of housing in Cusco; Evaluacion de la radioactividad natural en el rango gamma mediante un dosimetro manual en el interior y exterior de viviendas en el Cusco

Energy Technology Data Exchange (ETDEWEB)

Warthon, J.; Olarte, A.; Valencia, J., E-mail: juliowarthon@hotmail.com [Universidad Nacional de San Antonio Abad del Cusco, Facultad de Ciencias Quimicas, Fisicas y Matematicas, Av. de la Cultura No. 733, Cusco (Peru)

2014-08-15

The natural radioactivity is present in our environment and at any time the humans are exposed to this radiation type. In the 90 in Cusco city (Peru) were carried out measurements of environmental radioactivity for Umeres F. and L. Sajo, the information obtained by these investigators is valuable about the natural radioactivity in diverse places of the Cusco city; the current investigation consists on the measurement of the natural radioactivity inside and outside of the buildings in Cusco city. For 2013 and 2014 the radioactivity study has been programmed in the interior and exterior of constructions, the measures began in January 2013, to date has a considerable database. Each measures group consists of 100 tests in the interior and another similar quantity in the exterior of housing in the Cusco city; the measurement process was carried out with a manual dosimeter Geiger Muller-Zahlrohre, the average value obtained to the date is of 2.1 mSv/year which approaches to the average world value that is 2.4 mSv/year. (Author)

Interior insulation – Experimental investigation of hygrothermal conditions and damage evaluation of solid masonry façades in a listed building

DEFF Research Database (Denmark)

Odgaard, Tommy; Bjarløv, Søren Peter; Rode, Carsten

2018-01-01

Exterior walls in historic multi-storey buildings compared to walls in modern buildings have low thermal resistance, resulting in high energy loss and cold surfaces/floors in cold climates. When restrictions regarding alteration of the exterior appearance exist, interior insulation might be the o......Exterior walls in historic multi-storey buildings compared to walls in modern buildings have low thermal resistance, resulting in high energy loss and cold surfaces/floors in cold climates. When restrictions regarding alteration of the exterior appearance exist, interior insulation might...... be the only possibility to increase occupant comfort. This paper describes an investigation of the hygrothermal influence when applying 100 mm of diffusion open interior insulation to a historic multi-storey solid masonry spandrel. The dormitory room with the insulated spandrel had a normal indoor climate...... showed no risk of damage from the changed hygrothermal conditions when applying interior insulation to a solid masonry spandrel....

Discrete exterior calculus discretization of incompressible Navier–Stokes equations over surface simplicial meshes

KAUST Repository

Mohamed, Mamdouh S.; Hirani, Anil N.; Samtaney, Ravi

2016-01-01

A conservative discretization of incompressible Navier–Stokes equations is developed based on discrete exterior calculus (DEC). A distinguishing feature of our method is the use of an algebraic discretization of the interior product operator and a

Numerical investigation on exterior conformal mappings with application to airfoils

International Nuclear Information System (INIS)

Mohamad Rashidi Md Razali; Hu Laey Nee

2000-01-01

A numerical method is described in computing a conformal map from an exterior region onto the exterior of the unit disk. The numerical method is based on a boundary integral equation which is similar to the Kerzman-Stein integral equation for interior mapping. Some examples show that numerical results of high accuracy can be obtained provided that the boundaries are smooth. This numerical method has been applied to the mapping airfoils. However, due to the fact that the parametric representation of an air foil is not known, a cubic spline interpolation method has been used. Some numerical examples with satisfying results have been obtained for the symmetrical and cambered airfoils. (Author)

Vibrant Interior Reflects Lifestyle. 1974 Award Winning Architecture

Science.gov (United States)

American School and University, 1974

1974-01-01

The design of the student center at Essex Community College in Baltimore County, Maryland, reflects youthful lifestyles in the interior decor while providing exterior design to harmonize with existing campus buildings. (Author/MF)

Early User Appraisal of the MDARS Interior Robot

National Research Council Canada - National Science Library

Laird, R

1999-01-01

The Mobile Detection Assessment Response System (MDARS) is a joint Army-Navy effort to field interior and exterior autonomous platforms for security and inventory assessment functions at DoD warehouses and storage sites...

The theory of discourse in the linguistic scenario: a new route for the clash interior x exterior in the studies of the language

Directory of Open Access Journals (Sweden)

Daiany Bonácio

2017-10-01

Full Text Available The language has always aroused human interest. Since ancient times, it was discussed by wise men like Aristotle and Plato. Philosophers discoursed, for example, on the relationship between the names and the things which they named, if the relationship was natural or conventional, in an attempt to explain the functioning of the language. Such discussions fomented a question: the studies of the language should focus on what aspect? What is going on inside the subject, in his ability to speak? Or what goes on outside, the manifestation of the interior considering the social? This impasse was extending over the linguistic studies. Faced with the reality described, this article aimed to discuss the impasse between an approach to the language focused on interiority and another focused on the exteriority, tracing a route through language studies from the classics, through the materialist theory of Michel Pêcheux to reach concepts proposed by the philosopher Michel Foucault, which will be used for analysis from a discursive perspective. The Discourse Analysis tries to think Linguistic out of this issue of logicism and sociology: it proposes to look at the discourse, offering another field of study for the language.

The Weathering Study of PC/ASA Alloy For Automotive Exterior Applications

Directory of Open Access Journals (Sweden)

Sinan Öztürk

2017-10-01

Full Text Available Polycarbonates (PC are used in automotive industry due to high physical and mechanical properties like high impact resistance and ductility. Polycarbonates are blended with ABS (Acrylonitrile-Butadiene-Styrene and ASA (Acrylonitrile-Styrene-Acrylate terpolymers for interior and exterior applications of automotive components to achieve good physical and mechanical properties. Other reason for choosing such alloys for interior applications is the IZOD impact resistance requirement higher than 40kJ/m2. Recently, grades of PC/ASA with UV stabilized are developed for non-painted exterior applications. The aim of our study is to investigate whether new developed PC/ASA could be chosen for exterior applications of automotive industry. In this study, the samples are prepared from injection molding and the weathering performance of PC/ASA was tested by a weather-o-meter for 1500h at a total of 1890 kJ/m2 at 340nm with a cut-off filter at λ<290nm. The results are evaluated by FT-IR, DSC, TGA and SEM. It has been observed that UV degradation of PC/ASA leads to several major changes in its IR spectrum like broad bands occurred in the hydroxyl region around 3300 cm-1, and carbonyl stretching region increased around 1728 cm-1. The main degradations were based on photo-oxidation and photo-Fries rearrangement of PC. In our study, the photo-oxidation was followed by the color shift to yellowing of the polymer.

Ballistic characteristics improving and maintenance of protective ballistic vests

OpenAIRE

RADONJIC VOJKAN M.; JOVANOVIC DANKO M.; ZIVANOVIC GORAN Z.; RESIMIC BRANKO V.

2014-01-01

The work presents research of the materials necessary for the maintenance of protective ballistic vests. In this paper is proposed a new construction design with modern materials for ballistic inserts producing. This paper also presents the results of laboratory tests of ballistic cartridges with new materials. Based on the test results, it can be concluded, the proposed technical solution for making ballistic inserts adequately meets current standards.

Building of Requirement: Liberating Academic Interior Architecture

Science.gov (United States)

McLane, Yelena; Dawkins, Jim

2014-01-01

The authors focus on the strategies employed in the recent renovation of the William Johnston Building at Florida State University, in which the historical exterior was preserved, while the interiors were adapted to new functions as classrooms, study centers, and common spaces with intentionally undefined purposes. The building's various use…

Active control of turbulent boundary layer sound transmission into a vehicle interior

International Nuclear Information System (INIS)

Caiazzo, A; Alujević, N; Pluymers, B; Desmet, W

2016-01-01

In high speed automotive, aerospace, and railway transportation, the turbulent boundary layer (TBL) is one of the most important sources of interior noise. The stochastic pressure distribution associated with the turbulence is able to excite significantly structural vibration of vehicle exterior panels. They radiate sound into the vehicle through the interior panels. Therefore, the air flow noise becomes very influential when it comes to the noise vibration and harshness assessment of a vehicle, in particular at low frequencies. Normally, passive solutions, such as sound absorbing materials, are used for reducing the TBL-induced noise transmission into a vehicle interior, which generally improve the structure sound isolation performance. These can achieve excellent isolation performance at higher frequencies, but are unable to deal with the low-frequency interior noise components. In this paper, active control of TBL noise transmission through an acoustically coupled double panel system into a rectangular cavity is examined theoretically. The Corcos model of the TBL pressure distribution is used to model the disturbance. The disturbance is rejected by an active vibration isolation unit reacting between the exterior and the interior panels. Significant reductions of the low-frequency vibrations of the interior panel and the sound pressure in the cavity are observed. (paper)

Exterior and interior physical quality of egg of laying hens fed diets containing different dietary purslane levels

Science.gov (United States)

Kartikasari, L. R.; Hertanto, B. S.; Pranoto, D.; Salim, W. N.; Nuhriawangsa, A. M. P.

2017-04-01

Purslane is considered a rich vegetable source of alpha-linolenic acid, beta-carotene and various antioxidants. The objective of the study was to investigate the effect of different dietary levels of purslane meal (Portulaca oleracea) in the diets of laying hens on physical quality of eggs. A total of 125 Hy-Line Brown hens (54 weeks old) were placed at individual cages and assigned to five dietary treatments. The diets were supplemented with 0, 2, 4, 6 and 8% purslane meal. Laying hens were fed for 5 weeks after a typical period of adaptation (7 days). Water and feed were provided ad libitum. A total of 25 egg samples of day 28 and day 35 (n = 5 egg yolks for each treatment) were collected to analyse exterior and interior physical quality of eggs. The data were analysed using ANOVA. Differences between treatment means were further analysed using Duncan’s New Multiple Range Test. Results showed that feeding different purslane meal levels in the diets improved egg weight, yolk weight, albumen weight and yolk colour. The highest intensity of yolk colour was obtained with the diet containing 8% purslane meal. However, dietary treatments did not affect egg index, albumen index, yolk index, shell weight, shell thickness and Haugh Unit. It is concluded that including purslane meal to laying hen diets increases the physical qualities of the eggs.

Thermographic method for evaluation of thermal influence of exterior surface colour of buildings

Science.gov (United States)

Wu, Yanpeng; Li, Deying; Jin, Rendong; Liu, Li; Bai, Jiabin; Feng, Jianming

2008-12-01

Architecture colour is an important part in urban designing. It directly affects the expressing and the thermal effect of exterior surface of buildings. It has proved that four factors affect the sign visibility, graphics, colour, lighting condition and age of the observers, and colour is the main aspect. The best method is to prevent the exterior space heating up in the first place, by reflecting heat away room the exterior surface.The colour of paint to coat building's exterior wall can have a huge impact on energy efficiency. While the suitable colour is essential to increasing the energy efficiency of paint colour during the warm summer months, those products also help paint colour efficiency and reduce heat loss from buildings during winter months making the interior more comfortable all year long. The article is based on analyzing the importance of architecture color design and existing urban colour design. The effect of external surface colour on the thermal behaviour of a building has been studied experimentally by Infrared Thermographic method in University of Science and technology Beijing insummer.The experimental results showed that different colour has quietly different thermal effect on the exterior surface of buildings. The thermal effect of carmine and fawn has nearly the same values. The main factor which is color express, give some suggest ting about urban color design. The investigation reveals that the use of suitable surface colour can dramatically reduce maximum the temperatures of the exterior wall. Keywords: architectural colour, thermal, thermographic

Discrete exterior calculus discretization of incompressible Navier–Stokes equations over surface simplicial meshes

KAUST Repository

Mohamed, Mamdouh S.

2016-02-11

A conservative discretization of incompressible Navier–Stokes equations is developed based on discrete exterior calculus (DEC). A distinguishing feature of our method is the use of an algebraic discretization of the interior product operator and a combinatorial discretization of the wedge product. The governing equations are first rewritten using the exterior calculus notation, replacing vector calculus differential operators by the exterior derivative, Hodge star and wedge product operators. The discretization is then carried out by substituting with the corresponding discrete operators based on the DEC framework. Numerical experiments for flows over surfaces reveal a second order accuracy for the developed scheme when using structured-triangular meshes, and first order accuracy for otherwise unstructured meshes. By construction, the method is conservative in that both mass and vorticity are conserved up to machine precision. The relative error in kinetic energy for inviscid flow test cases converges in a second order fashion with both the mesh size and the time step.

Discrete exterior calculus discretization of incompressible Navier-Stokes equations over surface simplicial meshes

Science.gov (United States)

Mohamed, Mamdouh S.; Hirani, Anil N.; Samtaney, Ravi

2016-05-01

A conservative discretization of incompressible Navier-Stokes equations is developed based on discrete exterior calculus (DEC). A distinguishing feature of our method is the use of an algebraic discretization of the interior product operator and a combinatorial discretization of the wedge product. The governing equations are first rewritten using the exterior calculus notation, replacing vector calculus differential operators by the exterior derivative, Hodge star and wedge product operators. The discretization is then carried out by substituting with the corresponding discrete operators based on the DEC framework. Numerical experiments for flows over surfaces reveal a second order accuracy for the developed scheme when using structured-triangular meshes, and first order accuracy for otherwise unstructured meshes. By construction, the method is conservative in that both mass and vorticity are conserved up to machine precision. The relative error in kinetic energy for inviscid flow test cases converges in a second order fashion with both the mesh size and the time step.

Determining building interior structures using compressive sensing

Science.gov (United States)

Lagunas, Eva; Amin, Moeness G.; Ahmad, Fauzia; Nájar, Montse

2013-04-01

We consider imaging of the building interior structures using compressive sensing (CS) with applications to through-the-wall imaging and urban sensing. We consider a monostatic synthetic aperture radar imaging system employing stepped frequency waveform. The proposed approach exploits prior information of building construction practices to form an appropriate sparse representation of the building interior layout. We devise a dictionary of possible wall locations, which is consistent with the fact that interior walls are typically parallel or perpendicular to the front wall. The dictionary accounts for the dominant normal angle reflections from exterior and interior walls for the monostatic imaging system. CS is applied to a reduced set of observations to recover the true positions of the walls. Additional information about interior walls can be obtained using a dictionary of possible corner reflectors, which is the response of the junction of two walls. Supporting results based on simulation and laboratory experiments are provided. It is shown that the proposed sparsifying basis outperforms the conventional through-the-wall CS model, the wavelet sparsifying basis, and the block sparse model for building interior layout detection.

Improved iterative image reconstruction algorithm for the exterior problem of computed tomography

International Nuclear Information System (INIS)

Guo, Yumeng; Zeng, Li

2017-01-01

In industrial applications that are limited by the angle of a fan-beam and the length of a detector, the exterior problem of computed tomography (CT) uses only the projection data that correspond to the external annulus of the objects to reconstruct an image. Because the reconstructions are not affected by the projection data that correspond to the interior of the objects, the exterior problem is widely applied to detect cracks in the outer wall of large-sized objects, such as in-service pipelines. However, image reconstruction in the exterior problem is still a challenging problem due to truncated projection data and beam-hardening, both of which can lead to distortions and artifacts. Thus, developing an effective algorithm and adopting a scanning trajectory suited for the exterior problem may be valuable. In this study, an improved iterative algorithm that combines total variation minimization (TVM) with a region scalable fitting (RSF) model was developed for a unilateral off-centered scanning trajectory and can be utilized to inspect large-sized objects for defects. Experiments involving simulated phantoms and real projection data were conducted to validate the practicality of our algorithm. Furthermore, comparative experiments show that our algorithm outperforms others in suppressing the artifacts caused by truncated projection data and beam-hardening.

Improved iterative image reconstruction algorithm for the exterior problem of computed tomography

Energy Technology Data Exchange (ETDEWEB)

Guo, Yumeng [Chongqing University, College of Mathematics and Statistics, Chongqing 401331 (China); Chongqing University, ICT Research Center, Key Laboratory of Optoelectronic Technology and System of the Education Ministry of China, Chongqing 400044 (China); Zeng, Li, E-mail: drlizeng@cqu.edu.cn [Chongqing University, College of Mathematics and Statistics, Chongqing 401331 (China); Chongqing University, ICT Research Center, Key Laboratory of Optoelectronic Technology and System of the Education Ministry of China, Chongqing 400044 (China)

2017-01-11

In industrial applications that are limited by the angle of a fan-beam and the length of a detector, the exterior problem of computed tomography (CT) uses only the projection data that correspond to the external annulus of the objects to reconstruct an image. Because the reconstructions are not affected by the projection data that correspond to the interior of the objects, the exterior problem is widely applied to detect cracks in the outer wall of large-sized objects, such as in-service pipelines. However, image reconstruction in the exterior problem is still a challenging problem due to truncated projection data and beam-hardening, both of which can lead to distortions and artifacts. Thus, developing an effective algorithm and adopting a scanning trajectory suited for the exterior problem may be valuable. In this study, an improved iterative algorithm that combines total variation minimization (TVM) with a region scalable fitting (RSF) model was developed for a unilateral off-centered scanning trajectory and can be utilized to inspect large-sized objects for defects. Experiments involving simulated phantoms and real projection data were conducted to validate the practicality of our algorithm. Furthermore, comparative experiments show that our algorithm outperforms others in suppressing the artifacts caused by truncated projection data and beam-hardening.

Improved interior wall detection using designated dictionaries in compressive urban sensing problems

Science.gov (United States)

Lagunas, Eva; Amin, Moeness G.; Ahmad, Fauzia; Nájar, Montse

2013-05-01

In this paper, we address sparsity-based imaging of building interior structures for through-the-wall radar imaging and urban sensing applications. The proposed approach utilizes information about common building construction practices to form an appropriate sparse representation of the building layout. With a ground based SAR system, and considering that interior walls are either parallel or perpendicular to the exterior walls, the antenna at each position would receive reflections from the walls parallel to the radar's scan direction as well as from the corners between two meeting walls. We propose a two-step approach for wall detection and localization. In the first step, a dictionary of possible wall locations is used to recover the positions of both interior and exterior walls that are parallel to the scan direction. A follow-on step uses a dictionary of possible corner reflectors to locate wall-wall junctions along the detected wall segments, thereby determining the true wall extents and detecting walls perpendicular to the scan direction. The utility of the proposed approach is demonstrated using simulated data.

The Truth About Ballistic Coefficients

OpenAIRE

Courtney, Michael; Courtney, Amy

2007-01-01

The ballistic coefficient of a bullet describes how it slows in flight due to air resistance. This article presents experimental determinations of ballistic coefficients showing that the majority of bullets tested have their previously published ballistic coefficients exaggerated from 5-25% by the bullet manufacturers. These exaggerated ballistic coefficients lead to inaccurate predictions of long range bullet drop, retained energy and wind drift.

Investigation of interior post-insulated masonry walls with wooden beam ends

DEFF Research Database (Denmark)

Morelli, Martin; Svendsen, Svend

2013-01-01

The preponderant number of multistorey buildings constructed in Denmark in the period between 1850 and 1930 were built with masonry walls incorporating wooden floor beams. Given the nature of this construction, it is supposed that significant energy savings could be achieved by simply insulating...... the facades of such buildings. To maintain the exterior appearance of the facade, the only possible means of installing the required insulation is placing it on the interior of the wall. However, the installation of insulation on the interior of the wall assembly reduces the overall drying potential...

Interior-exterior connection in architectural design based on the incorporation of spatial in between layers. Study of four architectural projects

Directory of Open Access Journals (Sweden)

Krstić Hristina

2016-01-01

Full Text Available Different spatial layers in the architectural structure of a building can create particular spatial relations and an architectural space that cannot be defined as an inner space or as an outer space, but one which has the characteristics of both. This space, which can be called “in between space”, appears as the result of a specific design concept in which the architectural composition is created by gradual insertion of volumes one inside another, like a box that is placed inside a box, inside of which is placed another smaller box and so on. The incorporation of various layers in the spatial arrangement of volumes in certain architectural compositions can be conceived as a possible approach in connecting the interior and exterior. This kind of conceptual design distinguishes itself from the common approach by its specific architecture that offers richness, variety, complexity and unique perception of space, thereby increasing its value. The paper investigates this particular concept through the analysis of four residential houses (Villa Le Lac by Le Corbusier, Solar House by Oswald Mathias Ungers, House N by Sou Fujimoto and Guerrero House by Alberto Campo Baeza, and it strives to find out the concept’s use and advantages, all with the aim of opening up new possibilities in the design of buildings and enriching the design process.

75 FR 34170 - Plastic Omnium Automotive Exteriors, LLC, Anderson, SC; Plastic Omnium Automotive Exteriors, LLC...

Science.gov (United States)

2010-06-16

... Omnium Automotive Exteriors, LLC, Anderson, SC; Plastic Omnium Automotive Exteriors, LLC, Troy, MI... the Anderson, South Carolina location of Plastic Omnium Automotive Exteriors, LLC, working out of Troy... certification to include workers in support of the Anderson, South Carolina facility working out of Troy...

Retrofit with Interior Insulation on Solid Masonry Walls in Cool Temperate Climates

DEFF Research Database (Denmark)

Bjarløv, Søren Peter; Finken, G.R.; Odgaard, Tommy

2015-01-01

For historic buildings, where an alteration of the exterior façade is not wanted, interior insulation can be the solution to improve the indoor climate and reduce heat loss, but might also introduce moisture problems like condensation in the wall. Capillary active/hydrophilic insulation materials...... have been introduced to cope with the moisture problem. An extensive amount of calculations indicating where the challenges lie in the complex work with interior insulation in cool temperate climate has been carried out. In areas with high precipitation like Denmark, capillary active insulation may...

The Effects of Ballistic and Non-Ballistic Bench Press on Mechanical Variables.

Science.gov (United States)

Moir, Gavin L; Munford, Shawn N; Moroski, Lindsey L; Davis, Shala E

2017-02-21

To investigate the effects of ballistic and non-ballistic bench press performed with loads equivalent to 30 and 90% 1-repetition maximum (1-RM) on mechanical variables. Eleven resistance-trained men (age: 23.0 ± 1.4 years; mass: 98.4 ± 14.4 kg) attended four testing sessions where they performed one of the following sessions: 1) three sets of five non-ballistic repetitions performed with a load equivalent to 30% 1-RM (30N-B), 2) three sets of five ballistic repetitions performed with a load equivalent to 30% 1-RM (30B), 3) three sets of four non-ballistic repetitions with a load equivalent to 90% 1-RM (90N-B), 4) three sets of four ballistic repetitions with a load equivalent to 90% 1-RM (90B). Force plates and a 3-D motion analysis system were used to determine the velocity, force, power output (PO) and work during each repetition. The heavier loads resulted in significantly greater forces applied to the barbell (mean differences: 472-783 N, pvelocities (mean differences: 0.85-1.20 m/s, pvelocity (mean difference: 0.33 m/s, pbench press may be an effective exercise for developing power output and multiple sets may elicit post-activation potentiation that enhances force production. However, these benefits may be negated at heavier loads.

Is there ballistic transport in metallic nano-objects? Ballistic versus diffusive contributions

International Nuclear Information System (INIS)

Garcia, N; Bai Ming; Lu Yonghua; Munoz, M; Cheng Hao; Levanyuk, A P

2007-01-01

When discussing the resistance of an atomic-or nanometre-size contact we should consider both its ballistic and its diffusive contributions. But there is a contribution of the leads to the resistance of the contact as well. In this context, the geometry and the roughness of the surfaces limiting the system will contribute to the resistance, and these contributions should be added to the ideal ballistic resistance of the nanocontact. We have calculated, for metallic materials, the serial resistance of the leads arising from the roughness, and our calculations show that the ohmic resistance is as important as the ballistic resistance of the constriction. The classical resistance is a lower limit to the quantum resistance of the leads. Many examples of earlier experiments show that the mean free path of the transport electrons is of the order of the size of the contacts or the leads. This is not compatible with the idea of ballistic transport. This result may put in serious difficulties the current, existing interpretation of experimental data in metals where only small serial resistances compared with the ballistic component of the total resistance have been taken into account. The two-dimensional electron gas (2DEG) is also discussed and the serial corrections appear to be smaller than for metals. Experiments with these last systems are proposed that may reveal new interesting aspects in the physics of ballistic and diffusive transport

Terminal Ballistics

CERN Document Server

Rosenberg, Zvi

2012-01-01

This book covers the important issues of terminal ballistics in a comprehensive way combining experimental data, numerical simulations and analytical modeling. The first chapter reviews the experimental equipment which are used for ballistic tests and the diagnostics for material characterization under impulsive loading conditions. The second chapter covers essential features of the codes which are used for terminal ballistics such as the Euler vs. Lagrange schemes and meshing techniques, as well as the most popular material models. The third chapter, devoted to the penetration mechanics of rigid penetrators, brings the update of modeling in this field. The fourth chapter deals with plate perforation and the fifth chapter deals with the penetration mechanics of shaped charge jets and eroding long rods. The last two chapters discuss several techniques for the disruption and defeating of the main threats in armor design. Throughout the book the authors demonstrate the advantages of numerical simulations in unde...

Joint model to simulate inelastic shear behavior of poorly detailed exterior and interior beam-column connections reinforced with deformed bars under seismic excitations

International Nuclear Information System (INIS)

Sharma, Akanshu; Reddy, G.R.; Vaze, K.K.; Ghosh, A.K.; Kushwaha, H.S.; Eligehausen, Rolf

2009-12-01

A model for predicting the nonlinear shear behaviour of reinforced concrete beam column joints based on principal stresses reaching limits is proposed. The joint model proposes shear springs for the column region and rotational spring for the beam region of the joint. This is based on the actual displacement behaviour of the shear buildings. The spring characteristics are calculated based on well-known principal of mechanics using the principal stresses as the failure criteria. The model reasonably accurately predicts the shear behaviour of the joint and also can consider the effect of axial loads on the column. The model does not need any special element or special program for implementation and can be used for nonlinear static pushover analysis of RC framed structures giving due consideration to joint deformations. The model is therefore extremely useful for practical displacement based analysis of old RC buildings where the joints were not designed and detailed as per current codal requirements, invariably making them the weakest link in the structure. The background theory, assumptions followed and the complete formulations for generating the joint characteristics are given in this report. The model is validated with experimental results of tests on exterior and interior beam-column connections given in the published literature having substandard detailing using deformed bars. (author)

Ballistics considerations for small-caliber, low-density projectiles

International Nuclear Information System (INIS)

Gouge, M.J.; Baylor, L.R.; Combs, S.K.; Fisher, P.W.; Foster, C.A.; Foust, C.R.; Milora, S.L.; Qualls, A.L.

1993-01-01

One major application for single- and two-stage light gas guns is for fueling magnetic fusion confinement devices. Powder guns are not a feasible alternative due to possible plasma contamination by residual powder gases and the eventual requirement of steady-state operation at ∼ 1 Hz, which will dictate a closed gas handling system where propellant gases are recovered, processed and recompressed. Interior ballistic calculations for single-stage light gas guns, both analytical and numerical, are compared to an extensive data base for low density hydrogenic projectiles (pellets). Some innovative range diagnostics are described for determining the size and velocity of these small (several mm) size projectiles. A conceptual design of a closed cycle propellant gas system is presented including tradeoffs between different light propellant gases

Project Overcoat - An Exploration of Exterior Insulation Strategies for 1-1/2-Story Roof Applications in Cold Climates

Energy Technology Data Exchange (ETDEWEB)

Ojczyk, Cindy [NorthernSTAR Building America Partnership, St. Paul, MN (United States); Mosiman, Garrett [NorthernSTAR Building America Partnership, St. Paul, MN (United States); Huelman, Pat [NorthernSTAR Building America Partnership, St. Paul, MN (United States); Schirber, Tom [NorthernSTAR Building America Partnership, St. Paul, MN (United States); Yost, Peter [NorthernSTAR Building America Partnership, St. Paul, MN (United States); Murry, Tessa [NorthernSTAR Building America Partnership, St. Paul, MN (United States)

2013-04-01

The development of an alternative method to interior-applied insulation strategies or exterior applied 'band-aids' such as heat tapes and ice belts may help reduce energy needs of millions of 1-1/2 story homes while reducing the risk of ice dam formation. A potential strategy for energy improvement of the roof is borrowed from new construction best practices: Here an 'overcoat' of a continuous air, moisture, and thermal barrier is applied on the outside of the roof structure for improved overall performance. The continuous insulation of this approach facilitates a reduction in thermal bridging which could further reduce energy consumption and bring existing homes closer to meeting the Building America goals for energy reduction. Research favors an exterior approach to deep energy retrofits and ice dam prevention in existing homes. The greatest amount of research focuses on whole house deep energy retrofits leaving a void in roof-only applications. The research is also void of data supporting the hygrothermal performance, durability, constructability, and cost of roof-only exterior overcoat strategies. Yet, contractors interviewed for this report indicate an understanding that exterior approaches are most promising for mitigating ice dams and energy loss and are able to sell these strategies to homeowners.

Mechanism of ballistic collisions

International Nuclear Information System (INIS)

Sindoni, J.M.; Sharma, R.D.

1992-01-01

Ballistic collisions is a term used to describe atom-diatom collisions during which a substantial fraction of the initial relative translational energy is converted into the internal energy of the diatom. An exact formulation of the impulse approach to atom-diatom collisions is shown to be in excellent agreement with the experimental results for the CsF-Ar system at 1.1 eV relative translational energy for laboratory scattering angles of 30 degree and 60 degree. The differential cross section for scattering of CsF peaks at two distinct recoil velocities. The peak centered at the recoil velocity corresponding to elastic scattering has been called the elastic peak. This peak is shown to consist of several hundred inelastic transitions, most involving a small change in internal energy. The peak near the center-of-mass (c.m.) velocity is called the ballistic peak and is shown to consist of highly inelastic (ballistic) transitions. It is shown that transitions comprising the ballistic (elastic) peak occur when an Ar atom strikes the F (Cs) end of CsF. When one is looking along the direction of the c.m. velocity, the signal from a single transition, which converts about 99.99% of the relative translational energy into internal energy, may be larger than the signal from any other ballistic transition by as much as an order of magnitude. This property may be used to prepare state-selected and velocity-selected beams for further studies. It is also pointed out that the ballistic peak may be observed for any atom-molecule system under appropriate circumstances

Ballistic studies on layered structures

International Nuclear Information System (INIS)

Jena, P.K.; Ramanjeneyulu, K.; Siva Kumar, K.; Balakrishna Bhat, T.

2009-01-01

This paper presents the ballistic behavior and penetration mechanism of metal-metal and metal-fabric layered structures against 7.62 armour piercing projectiles at a velocity of 840 ± 15 m/s at 30 o angle of impact and compares the ballistic results with that of homogeneous metallic steel armour. This study also describes the effect of keeping a gap between the target layers. Experimental results showed that among the investigated materials, the best ballistic performance was attained with metal-fabric layered structures. The improvements in ballistic performance were analyzed in terms of mode of failure and fracture mechanisms of the samples by using optical and electron microscope, X-ray radiography and hardness measurement equipments.

A simplified model of dynamic interior cooling load evaluation for office buildings

International Nuclear Information System (INIS)

Ding, Yan; Zhang, Qiang; Wang, Zhaoxia; Liu, Min; He, Qing

2016-01-01

Highlights: • The core interior disturbance was determined by principle component analysis. • Influences of occupants on cooling load should be described using time series. • A simplified model was built to evaluate dynamic interior building cooling load. - Abstract: Predicted cooling load is a valuable tool for assessing the operation of air-conditioning systems. Compared with exterior cooling load, interior cooling load is more unpredictable. According to principle components analysis, occupancy was proved to be a typical factor influencing interior cooling loads in buildings. By exploring the regularity of interior disturbances in an office building, a simplified evaluation model for interior cooling load was established in this paper. The stochastic occupancy rate was represented by a Markov transition model. Equipment power, lighting power and fresh air were all related to occupancy rate based on time sequence. The superposition of different types of interior cooling loads was also considered in the evaluation model. The error between the evaluation results and measurement results was found to be lower than 10%. In reference to the cooling loads calculated by the traditional design method and area-based method in case study office rooms, the evaluated cooling loads were suitable for operation regulation.

Conformable Self-Healing Ballistic Armor

Science.gov (United States)

2011-06-28

public release, distribution unlimited 13. SUPPLEMENTARY NOTES Patent No: US 7,966,923 B2 14. ABSTRACT 15. SUBJECT TERMS 16. SECURITY CLASSIFICATION...B2 5 Each unit of shell 10 of the ballistic annor of the subject invention further comprises fastening means 20 to attach each such shell IOta the...selectively affixing the conformable ballistic annor to the vehicle is a secure manner, both on a temporal)’ orpennanent basis. The ballistic

Buildings vs. ballistics: Quantifying the vulnerability of buildings to volcanic ballistic impacts using field studies and pneumatic cannon experiments

Science.gov (United States)

Williams, G. T.; Kennedy, B. M.; Wilson, T. M.; Fitzgerald, R. H.; Tsunematsu, K.; Teissier, A.

2017-09-01

Recent casualties in volcanic eruptions due to trauma from blocks and bombs necessitate more rigorous, ballistic specific risk assessment. Quantitative assessments are limited by a lack of experimental and field data on the vulnerability of buildings to ballistic hazards. An improved, quantitative understanding of building vulnerability to ballistic impacts is required for informing appropriate life safety actions and other risk reduction strategies. We assessed ballistic impacts to buildings from eruptions at Usu Volcano and Mt. Ontake in Japan and compiled available impact data from eruptions elsewhere to identify common damage patterns from ballistic impacts to buildings. We additionally completed a series of cannon experiments which simulate ballistic block impacts to building claddings to investigate their performance over a range of ballistic projectile velocities, masses and energies. Our experiments provide new insights by quantifying (1) the hazard associated with post-impact shrapnel from building and rock fragments; (2) the effect of impact obliquity on damage; and (3) the additional impact resistance buildings possess when claddings are struck in areas directly supported by framing components. This was not well identified in previous work which may have underestimated building vulnerability to ballistic hazards. To improve assessment of building vulnerability to ballistics, we use our experimental and field data to develop quantitative vulnerability models known as fragility functions. Our fragility functions and field studies show that although unreinforced buildings are highly vulnerable to large ballistics (> 20 cm diameter), they can still provide shelter, preventing death during eruptions.

On exterior variational calculus

International Nuclear Information System (INIS)

Aldrovandi, R.; Kraenkel, R.A.

1987-01-01

Exterior variational calculus is introduced through examples in field theory. It provides a very simple technique to decide on the existence of Lagrangians for given equations of motions and, in the case, to find them. Only local aspects are discussed but the analogy to exterior calculus on finite dimensional manifolds is complete, strongly suggesting its suitability to the study of topological aspects. (Author) [pt

A primer on exterior differential calculus

Directory of Open Access Journals (Sweden)

Burton D.A.

2003-01-01

Full Text Available A pedagogical application-oriented introduction to the cal­culus of exterior differential forms on differential manifolds is presented. Stokes' theorem, the Lie derivative, linear con­nections and their curvature, torsion and non-metricity are discussed. Numerous examples using differential calculus are given and some detailed comparisons are made with their tradi­tional vector counterparts. In particular, vector calculus on R3 is cast in terms of exterior calculus and the traditional Stokes' and divergence theorems replaced by the more powerful exterior expression of Stokes' theorem. Examples from classical continuum mechanics and spacetime physics are discussed and worked through using the language of exterior forms. The numerous advantages of this calculus, over more traditional ma­chinery, are stressed throughout the article. .

Management of civilian ballistic fractures.

Science.gov (United States)

Seng, V S; Masquelet, A C

2013-12-01

The management of ballistic fractures, which are open fractures, has often been studied in wartime and has benefited from the principles of military surgery with debridement and lavage, and the use of external fixation for bone stabilization. In civilian practice, bone stabilization of these fractures is different and is not performed by external fixation. Fifteen civilian ballistic fractures, Gustilo II or IIIa, two associated with nerve damage and none with vascular damage, were reviewed. After debridement and lavage, ten internal fixations and five conservative treatments were used. No superficial or deep surgical site infection was noted. Fourteen of the 15 fractures (93%) healed without reoperation. Eleven of the 15 patients (73%) regained normal function. Ballistic fractures have a bad reputation due to their many complications, including infections. In civilian practice, the use of internal fixation is not responsible for excessive morbidity, provided debridement and lavage are performed. Civilian ballistic fractures, when they are caused by low-velocity firearms, differ from military ballistic fractures. Although the principle of surgical debridement and lavage remains the same, bone stabilization is different and is similar to conventional open fractures. Copyright © 2013 Elsevier Masson SAS. All rights reserved.

Reduction of interior sound fields in flexible cylinders by active vibration control

Science.gov (United States)

Jones, J. D.; Fuller, C. R.

1988-01-01

The mechanisms of interior sound reduction through active control of a thin flexible shell's vibrational response are presently evaluated in view of an analytical model. The noise source is a single exterior acoustic monopole. The active control model is evaluated for harmonic excitation; the results obtained indicate spatially-averaged noise reductions in excess of 20 dB over the source plane, for acoustic resonant conditions inside the cavity.

Exterior differentials in superspace and Poisson brackets

International Nuclear Information System (INIS)

Soroka, Dmitrij V.; Soroka, Vyacheslav A.

2003-01-01

It is shown that two definitions for an exterior differential in superspace, giving the same exterior calculus, yet lead to different results when applied to the Poisson bracket. A prescription for the transition with the help of these exterior differentials from the given Poisson bracket of definite Grassmann parity to another bracket is introduced. It is also indicated that the resulting bracket leads to generalization of the Schouten-Nijenhuis bracket for the cases of superspace and brackets of diverse Grassmann parities. It is shown that in the case of the Grassmann-odd exterior differential the resulting bracket is the bracket given on exterior forms. The above-mentioned transition with the use of the odd exterior differential applied to the linear even/odd Poisson brackets, that correspond to semi-simple Lie groups, results, respectively, in also linear odd/even brackets which are naturally connected with the Lie superalgebra. The latter contains the BRST and anti-BRST charges and can be used for calculation of the BRST operator cogomology. (author)

Ballistic properties of bidirectional fiber/resin composites

OpenAIRE

Dimeski, Dimko; Spaseska, Dijana

2004-01-01

The aim of the research was to make evaulation of the ballistic strenth of four different composites intended to be used in manufacturing of ballistic items for personal protection. Research has been performed on glass, ntlon, HPPE and aramide fibers...... Key words. aramid, ballistic, V50

Ballistic electron transport in mesoscopic samples

International Nuclear Information System (INIS)

Diaconescu, D.

2000-01-01

In the framework of this thesis, the electron transport in the ballistic regime has been studied. Ballistic means that the lateral sample dimensions are smaller than the mean free path of the electrons, i.e. the electrons can travel through the whole device without being scattered. This leads to transport characteristics that differ significantly from the diffusive regime which is realised in most experiments. Making use of samples with high mean free path, features of ballistic transport have been observed on samples with sizes up to 100 μm. The basic device used in ballistic electron transport is the point contact, from which a collimated beam of ballistic electrons can be injected. Such point contacts were realised with focused ion beam (FIB) implantation and the collimating properties were analysed using a two opposite point contact configuration. The typical angular width at half maximum is around 50 , which is comparable with that of point contacts defined by other methods. (orig.)

Dense-plasma research using ballistic compressors

International Nuclear Information System (INIS)

Hess, H.

1986-01-01

An introduction is given to research on dense (or nonideal) plasmas which can be generated to advantage by ballistic compressors. Some properties of ballistic compressors are discussed especially in comparison with shock tubes. A short review is given on the history of these devices for high-pressure plasma generation. The present state of the art is reported including research on the two ZIE (Central Institute for Electron Physics) ballistic compressors. (author)

Ballistic transport and electronic structure

NARCIS (Netherlands)

Schep, Kees M.; Kelly, Paul J.; Bauer, Gerrit E.W.

1998-01-01

The role of the electronic structure in determining the transport properties of ballistic point contacts is studied. The conductance in the ballistic regime is related to simple geometrical projections of the Fermi surface. The essential physics is first clarified for simple models. For real

Ship Anti Ballistic Missile Response (SABR)

OpenAIRE

Johnson, Allen P.; Breeden, Bryan; Duff, Willard Earl; Fishcer, Paul F.; Hornback, Nathan; Leiker, David C.; Carlisle, Parker; Diersing, Michael; Devlin, Ryan; Glenn, Christopher; Hoffmeister, Chris; Chong, Tay Boon; Sing, Phang Nyit; Meng, Low Wee; Meng, Fann Chee

2006-01-01

Includes supplementary material. Based on public law and Presidential mandate, ballistic missile defense development is a front-burner issue for homeland defense and the defense of U.S. and coalition forces abroad. Spearheaded by the Missile Defense Agency, an integrated ballistic missile defense system was initiated to create a layered defense composed of land-, air-, sea-, and space-based assets. The Ship Anti-Ballistic Response (SABR) Project is a systems engineering approach t...

Ballistic properties of bidirectional fiber/resin composites

International Nuclear Information System (INIS)

Dimeski, Dimko; Spaseska, Dijana

2004-01-01

The aim of the research was to make evaluation of the ballistic strength of four different fiber/resin composites intended to be used in manufacturing of ballistic items for personal protection. Research has been performed on glass, ballistic nylon, aramid and HPPE (High Performance Polyethylene) plainly woven fabric based composites. As a matrix system, in all cases, polyvinylbutyral modified phenolic resin was used. For the investigation, areal weight range 2 - 9 kg/m 2 chosen was, which is applicable for personal ballistic protection and the ultimate resin content range 20 - 50 vol.%. Ballistic test of the composites has shown that the best results exhibit HPPE based composites; aramid based composites have been the second best followed by the polyamide based composites. The worst results have been shown by the glass based composites. All composites with lower resin content (20%) have performed much better than their counterparts with higher resin content (50 %).The plot of the ballistic strength (V 50 ) versus areal weight has shown a linear increase of V 50 with the increase of areal weight. The ballistic strength of the composites is highly dependant on the fiber/resin ratio and increases with the increase of the fiber content. (Author)

Ballistic phonon transport in holey silicon.

Science.gov (United States)

Lee, Jaeho; Lim, Jongwoo; Yang, Peidong

2015-05-13

When the size of semiconductors is smaller than the phonon mean free path, phonons can carry heat with no internal scattering. Ballistic phonon transport has received attention for both theoretical and practical aspects because Fourier's law of heat conduction breaks down and the heat dissipation in nanoscale transistors becomes unpredictable in the ballistic regime. While recent experiments demonstrate room-temperature evidence of ballistic phonon transport in various nanomaterials, the thermal conductivity data for silicon in the length scale of 10-100 nm is still not available due to experimental challenges. Here we show ballistic phonon transport prevails in the cross-plane direction of holey silicon from 35 to 200 nm. The thermal conductivity scales linearly with the length (thickness) even though the lateral dimension (neck) is as narrow as 20 nm. We assess the impact of long-wavelength phonons and predict a transition from ballistic to diffusive regime using scaling models. Our results support strong persistence of long-wavelength phonons in nanostructures and are useful for controlling phonon transport for thermoelectrics and potential phononic applications.

Family of regular interiors for nonrotating black holes with T00=T11

International Nuclear Information System (INIS)

Elizalde, Emilio; Hildebrandt, Sergi R.

2002-01-01

We find the general solution for the spacetimes describing the interior of static black holes with an equation of state of the type T 0 0 =T 1 1 (T being the stress-energy tensor). This form is the one expected from taking into account different quantum effects associated with strong gravitational fields. We recover all the particular examples found in the literature. We remark that all the solutions found follow the natural scheme of an interior core linked smoothly with the exterior solution by a transient region. We also discuss their local energy properties and give the main ideas involved in a possible generalization of the scheme in order to include other realistic types of sources

Modeling thermal performance of exterior walls retrofitted from insulation and modified laterite based bricks materials

Science.gov (United States)

Wati, Elvis; Meukam, Pierre; Damfeu, Jean Claude

2017-12-01

Uninsulated concrete block walls commonly found in tropical region have to be retrofitted to save energy. The thickness of insulation layer used can be reduced with the help of modified laterite based bricks layer (with the considerably lower thermal conductivity than that of concrete block layer) during the retrofit building fabrics. The aim of this study is to determine the optimum location and distribution of different materials. The investigation is carried out under steady periodic conditions under the climatic conditions of Garoua in Cameroon using a Simulink model constructed from H-Tools (the library of Simulink models). Results showed that for the continuous air-conditioned space, the best wall configuration from the maximum time lag, minimum decrement factor and peak cooling transmission load perspective, is dividing the insulation layer into two layers and placing one at the exterior surface and the other layer between the two different massive layers with the modified laterite based bricks layer at the interior surface. For intermittent cooling space, the best wall configuration from the minimum energy consumption depends on total insulation thickness. For the total insulation thickness less than 8 cm approximately, the best wall configuration is placing the half layer of insulation material at the interior surface and the other half between the two different massive layers with the modified earthen material at the exterior surface. Results also showed that, the optimum insulation thickness calculated from the yearly cooling transmission (estimated only during the occupied period) and some economic considerations slightly depends on the location of that insulation.

Ballistic resistance capacity of carbon nanotubes

International Nuclear Information System (INIS)

Mylvaganam, Kausala; Zhang, L C

2007-01-01

Carbon nanotubes have high strength, light weight and excellent energy absorption capacity and therefore have great potential applications in making antiballistic materials. By examining the ballistic impact and bouncing-back processes on carbon nanotubes, this investigation shows that nanotubes with large radii withstand higher bullet speeds and the ballistic resistance is the highest when the bullet hits the centre of the CNT; the ballistic resistance of CNTs will remain the same on subsequent bullet strikes if the impact is after a small time interval

Hollow Nanospheres with Fluorous Interiors for Transport of Molecular Oxygen in Water

KAUST Repository

Vu, Khanh B.

2016-08-11

A dispersion system for saturated fluorocarbon (SFC) liquids based on permeable hollow nanospheres with fluorous interiors is described. The nanospheres are well dispersible in water and are capable of immediate uptake of SFCs. The nanosphere shells are gas-permeable and feature reactive functional groups for easy modification of the exterior. These features make the SFC-filled nanospheres promising vehicles for respiratory oxygen storage and transport. Uptake of molecular oxygen into nanosphere-stabilized SFC dispersions is demonstrated.

Supra-ballistic phonons

International Nuclear Information System (INIS)

Russell, F.M.

1989-05-01

Energetic particles moving with a solid, either from nuclear reactions or externally injected, deposit energy by inelastic scattering processes which eventually appears as thermal energy. If the transfer of energy occurs in a crystalline solid then it is possible to couple some of the energy directly to the nuclei forming the lattice by generating phonons. In this paper the transfer of energy from a compound excited nucleus to the lattice is examined by introducing a virtual particle Π. It is shown that by including a Π in the nuclear reaction a substantial amount of energy can be coupled directly to the lattice. In the lattice this particle behaves as a spatially localized phonon of high energy, the so-called supra-ballistic phonon. By multiple inelastic scattering the supra-ballistic phonon eventually thermalizes. Because both the virtual particle Π and the equivalent supra-ballistic phonon have no charge or spin and can only exist within a lattice it is difficult to detect other than by its decay into thermal phonons. The possibility of a Π removing excess energy from a compound nucleus formed by the cold fusion of deuterium is examined. (Author)

The Cooperative Ballistic Missile Defence Game

NARCIS (Netherlands)

Evers, L.; Barros, A.I.; Monsuur, H.

2013-01-01

The increasing proliferation of ballistic missiles and weapons of mass destruction poses new risks worldwide. For a threatened nation and given the characteristics of this threat a layered ballistic missile defence system strategy appears to be the preferred solution. However, such a strategy

Tensor spaces and exterior algebra

CERN Document Server

Yokonuma, Takeo

1992-01-01

This book explains, as clearly as possible, tensors and such related topics as tensor products of vector spaces, tensor algebras, and exterior algebras. You will appreciate Yokonuma's lucid and methodical treatment of the subject. This book is useful in undergraduate and graduate courses in multilinear algebra. Tensor Spaces and Exterior Algebra begins with basic notions associated with tensors. To facilitate understanding of the definitions, Yokonuma often presents two or more different ways of describing one object. Next, the properties and applications of tensors are developed, including the classical definition of tensors and the description of relative tensors. Also discussed are the algebraic foundations of tensor calculus and applications of exterior algebra to determinants and to geometry. This book closes with an examination of algebraic systems with bilinear multiplication. In particular, Yokonuma discusses the theory of replicas of Chevalley and several properties of Lie algebras deduced from them.

Evaluation of Aero Commander sidewall vibration and interior acoustic data: Static operations

Science.gov (United States)

Piersol, A. G.; Wilby, E. G.; Wilby, J. F.

1980-01-01

Results for the vibration measured at five locations on the fuselage structure during static operations are presented. The analysis was concerned with the magnitude of the vibration and the relative phase between different locations, the frequency response (inertance) functions between the exterior pressure field and the vibration, and the coherent output power functions at interior microphone locations based on sidewall vibration. Fuselage skin panels near the plane of rotation of the propeller accept propeller noise excitation more efficiently than they do exhaust noise.

Ballistic materials in MR imaging

International Nuclear Information System (INIS)

Smith, A.S.; Hurst, G.C.; Duerk, J.L.; Diaz, P.J.

1990-01-01

This paper reports on the most common ballistic materials available in the urban setting studied for deflection force, rotation, heating, and imaging artifact at 1.5 T to determine potential efficacy and safety for imaging patients with ballistic injuries. Twenty-eight missiles were tested, covering the range of bullet types and materials suggested by the Cleveland Police Department. Deflection force was measured by the New method. Rotation was studied by evaluating bullets in a 10% (W/W) ballistic gelating after 30 minutes with the long axis of the bullet placed parallel and perpendicular to the z axis. Heating was measured with alcohol thermometers imaged for 1 hour alternately with FESUM and spin-echo sequences (RF absorption w/Kg and 0.033 w/Kg). Image artifact evaluation of routine sequences was performed

Feasibility of ballistic strengthening exercises in neurologic rehabilitation.

Science.gov (United States)

Williams, Gavin; Clark, Ross A; Hansson, Jessica; Paterson, Kade

2014-09-01

Conventional methods for strength training in neurologic rehabilitation are not task specific for walking. Ballistic strength training was developed to improve the functional transfer of strength training; however, no research has investigated this in neurologic populations. The aim of this pilot study was to evaluate the feasibility of applying ballistic principles to conventional leg strengthening exercises in individuals with mobility limitations as a result of neurologic injuries. Eleven individuals with neurologic injuries completed seated and reclined leg press using conventional and ballistic techniques. A 2 × 2 repeated-measures analysis of variance was used to compare power measures (peak movement height and peak velocity) between exercises and conditions. Peak jump velocity and peak jump height were greater when using the ballistic jump technique rather than the conventional concentric technique (P ballistic principles was associated with increased peak height and peak velocities.

Ballistic missile defense effectiveness

Science.gov (United States)

Lewis, George N.

2017-11-01

The potential effectiveness of ballistic missile defenses today remains a subject of debate. After a brief discussion of terminal and boost phase defenses, this chapter will focus on long-range midcourse defenses. The problems posed by potential countermeasures to such midcourse defenses are discussed as are the sensor capabilities a defense might have available to attempt to discriminate the actual missile warhead in a countermeasures environment. The role of flight testing in assessing ballistic missile defense effectiveness is discussed. Arguments made about effectiveness by missile defense supporters and critics are summarized.

Two distinct ballistic processes in graphene

International Nuclear Information System (INIS)

Lewkowicz, M; Rosenstein, B; Nghiem, D

2012-01-01

A dynamical approach to ballistic transport in mesoscopic graphene samples of finite length Land contact potential difference with leads U is developed. It is shown that at ballistic times shorter than both relevant time scales, t L = L/v g (v g - Fermi velocity) and t u = ħ/(eU), the major effect of electric field is to creates the electron - hole pairs, namely causes interband transitions. At ballistic times lager than the two scales the mechanism is very different. The conductivity has its “nonrelativistic” or intraband value equal to the one obtained within the Landauer-Butticker approach for the barrier Uresulting from evanescent waves tunneling through the barrier.

Ballistic self-annealing during ion implantation

International Nuclear Information System (INIS)

Prins, Johan F.

2001-01-01

Ion implantation conditions are considered during which the energy, dissipated in the collision cascades, is low enough to ensure that the defects, which are generated during these collisions, consist primarily of vacancies and interstitial atoms. It is proposed that ballistic self-annealing is possible when the point defect density becomes high enough, provided that none, or very few, of the interstitial atoms escape from the layer being implanted. Under these conditions, the fraction of ballistic atoms, generated within the collision cascades from substitutional sites, decreases with increasing ion dose. Furthermore, the fraction of ballistic atoms, which finally end up within vacancies, increases with increasing vacancy density. Provided the crystal structure does not collapse, a damage threshold should be approached where just as many atoms are knocked out of substitutional sites as the number of ballistic atoms that fall back into vacancies. Under these conditions, the average point defect density should approach saturation. This model is applied to recently published Raman data that have been measured on a 3 MeV He + -ion implanted diamond (Orwa et al 2000 Phys. Rev. B 62 5461). The conclusion is reached that this ballistic self-annealing model describes the latter data better than a model in which it is assumed that the saturation in radiation damage is caused by amorphization of the implanted layer. (author)

Room-temperature ballistic transport in III-nitride heterostructures.

Science.gov (United States)

Matioli, Elison; Palacios, Tomás

2015-02-11

Room-temperature (RT) ballistic transport of electrons is experimentally observed and theoretically investigated in III-nitrides. This has been largely investigated at low temperatures in low band gap III-V materials due to their high electron mobilities. However, their application to RT ballistic devices is limited by their low optical phonon energies, close to KT at 300 K. In addition, the short electron mean-free-path at RT requires nanoscale devices for which surface effects are a limitation in these materials. We explore the unique properties of wide band-gap III-nitride semiconductors to demonstrate RT ballistic devices. A theoretical model is proposed to corroborate experimentally their optical phonon energy of 92 meV, which is ∼4× larger than in other III-V semiconductors. This allows RT ballistic devices operating at larger voltages and currents. An additional model is described to determine experimentally a characteristic dimension for ballistic transport of 188 nm. Another remarkable property is their short carrier depletion at device sidewalls, down to 13 nm, which allows top-down nanofabrication of very narrow ballistic devices. These results open a wealth of new systems and basic transport studies possible at RT.

The effects of drain scatterings on the electron transport properties of strained-Si diodes with ballistic and non-ballistic channels

International Nuclear Information System (INIS)

Yasenjan Ghupur; Mamtimin Geni; Mamatrishat Mamat; Abudukelimu Abudureheman

2015-01-01

The effects of multiple scattering on the electron transport properties in drain regions are numerically investigated for the cases of strained-Si diodes with or without scattering in the channel. The performance of non-ballistic (with scattering) channel Si-diodes is compared with that of ballistic (without scattering) channel Si-diodes, using the strain and scattering model. Our results show that the values of the electron velocity and the current in the strain model are higher than the respective values in the unstrained model, and the values of the velocity and the current in the ballistic channel model are higher than the respective values in the non-ballistic channel model. In the strain and scattering models, the effect of each carrier scattering mechanism on the performance of the Si-diodes is analyzed in the drain region. For the ballistic channel model, our results show that inter-valley optical phonon scattering improves device performance, whereas intra-valley acoustic phonon scattering degrades device performance. For the strain model, our results imply that the larger energy splitting of the strained Si could suppress the inter-valley phonon scattering rate. In conclusion, for the drain region, investigation of the strained-Si and scattering mechanisms are necessary, in order to improve the performance of nanoscale ballistic regime devices. (paper)

Metodología de diseño, observación y cálculo de redes geodésicas exteriores para túneles de gran longitud

Directory of Open Access Journals (Sweden)

Velasco, J.

2014-03-01

Full Text Available The realization of long railway tunnels has acquired a great interest in recent years. In Spain it is necessary to address projects of this nature, but ther is no corresponding methodological framework supporting them. The tunnel observational and working geometrical properties, make that former methodologies used may be unuseful in this case: the observation of the exterior and interior geodetical networks of the tunnel is different in nature. Conditions of visibility in the interior of the tunnels, regardless of the geometry, are not the most advantageous for observation due to the production system and the natural conditions of the tunnels. Errors increase as the drilling of the tunnel progresses, as it becomes problematical to perform continuous verifications along the itinerary itself. Moreover, inherent tunnel movements due to active geodynamics must also be considered. Therefore patterns for geodetic and topographic observations have to be reviewed when very long tunnels are constructed.La realización de túneles de gran longitud para ferrocarriles ha adquirido un gran auge en los últimos años. En España se han abordado proyectos de estas características, no existiendo para su ejecución una metodología completa y contrastada de actuación. Las características geométricas, de observación y de trabajo en túneles hace que las metodologías que se aplican en otros proyectos de ingeniería no sean aplicables por las siguientes causas: separación de las redes exteriores e interiores de los túneles debido a la diferente naturaleza de los observables, geometría en el interior siempre desfavorable a los requerimientos de observación clásica, mala visibilidad dentro del túnel, aumento de errores conforme avanza la perforación, y movimientos propios del túnel durante su ejecución por la propia geodinámica activa. Los patrones de observación geodésica usados deben revisarse cuando se ejecutan túneles de gran longitud. Este

Ballistic Test Facility

Data.gov (United States)

Federal Laboratory Consortium — The Ballistic Test Facility is comprised of two outdoor and one indoor test ranges, which are all instrumented for data acquisition and analysis. Full-size aircraft...

Preservation and storage of prepared ballistic gelatine.

Science.gov (United States)

Mattijssen, E J A T; Alberink, I; Jacobs, B; van den Boogaard, Y

2016-02-01

The use of ballistic gelatine, generally accepted as a human muscle tissue simulant in wound ballistic studies, might be improved by adding a preservative (Methyl 4-hydroxybenzoate) which inhibits microbial growth. This study shows that replacing a part of the gelatine powder by the preservative does not significantly alter the penetration depth of projectiles. Storing prepared blocks of ballistic gelatine over time decreased the penetration depth of projectiles. Storage of prepared gelatine for 4 week already showed a significant effect on the penetration depth of projectiles. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

Assessment of Ballistic Performance for Transparent Material

Directory of Open Access Journals (Sweden)

Basim M. Fadhil

2014-05-01

Full Text Available A finite element method was used to investigate the ballistic behavior of Polymethylmethacrylate (PMMA under impact loading by spherical steel projectile with different ranges of velocities. Three different target thicknesses were used in the experimental and the numerical works. A mathematical model has been used for the ballistic limit based on the experimental results. It has been found that projectile velocity and target thickness play an important role in the ballistic behavior of PMMA. A good agreement was found between the numerical, experimental, and the analytical result.

Injuries of the head from backface deformation of ballistic protective helmets under ballistic impact.

Science.gov (United States)

Rafaels, Karin A; Cutcliffe, Hattie C; Salzar, Robert S; Davis, Martin; Boggess, Brian; Bush, Bryan; Harris, Robert; Rountree, Mark Steve; Sanderson, Ellory; Campman, Steven; Koch, Spencer; Dale Bass, Cameron R

2015-01-01

Modern ballistic helmets defeat penetrating bullets by energy transfer from the projectile to the helmet, producing helmet deformation. This deformation may cause severe injuries without completely perforating the helmet, termed "behind armor blunt trauma" (BABT). As helmets become lighter, the likelihood of larger helmet backface deformation under ballistic impact increases. To characterize the potential for BABT, seven postmortem human head/neck specimens wearing a ballistic protective helmet were exposed to nonperforating impact, using a 9 mm, full metal jacket, 124 grain bullet with velocities of 400-460 m/s. An increasing trend of injury severity was observed, ranging from simple linear fractures to combinations of linear and depressed fractures. Overall, the ability to identify skull fractures resulting from BABT can be used in forensic investigations. Our results demonstrate a high risk of skull fracture due to BABT and necessitate the prevention of BABT as a design factor in future generations of protective gear. © 2014 American Academy of Forensic Sciences.

Recessed and influence evolution of inside temperatures of buildings in warm moist climates; El retranqueo y su influencia en la evolucion de las temperaturas interiores de edificios en climas calidos humedos

Energy Technology Data Exchange (ETDEWEB)

Machado, Maria V; Quiros, Carlos; Rubio, Dalmary [Instituto de Investigaciones de la Facultad de Arquitectura de la Universidad del Zulia, Maracaibo (Venezuela)

2000-07-01

The use of combined solar protections and recessed windows in buildings, evidentially reduces the heat gain towards the interior of spaces, because the greatest part of the building's heat gain is received by solar radiation that penetrates through the windows. In this investigation the influence of the dimension of recessed windows in the heat and temperature gain of interior air will be determined. In order to simulate interior conditions CODYBA software was used, applied to a model room of 9 m{sup 2} with one facade exposed to the exterior and a window 2/3 the size of the facade. [Spanish] El uso de protecciones solares y del retranqueo en las aberturas en las edificaciones evidentemente reduce la ganancia de calor hacia el interior de los espacios, ya que la mayor parte del aporte calorifico a las edificaciones lo constituye la radiacion solar que penetra a traves de las ventanas. En este trabajo se determinara la influencia que tiene la dimension del retranqueo de las ventanas en las ganancias de calor y las temperaturas del aire interior. Para simular las condiciones interiores se ha utilizado el programa de computacion CODYBA, aplicado a una habitacion de 9 m{sup 2} , con una sola fachada expuesta al exterior y una abertura igual a 2/3 del tamano de la fachada.

Ballistic deficit correction

International Nuclear Information System (INIS)

Duchene, G.; Moszynski, M.; Curien, D.

1991-01-01

The EUROGAM data-acquisition has to handle a large number of events/s. Typical in-beam experiments using heavy-ion fusion reactions assume the production of about 50 000 compound nuclei per second deexciting via particle and γ-ray emissions. The very powerful γ-ray detection of EUROGAM is expected to produce high-fold event rates as large as 10 4 events/s. Such high count rates introduce, in a common dead time mode, large dead times for the whole system associated with the processing of the pulse, its digitization and its readout (from the preamplifier pulse up to the readout of the information). In order to minimize the dead time the shaping time constant τ, usually about 3 μs for large volume Ge detectors has to be reduced. Smaller shaping times, however, will adversely affect the energy resolution due to ballistic deficit. One possible solution is to operate the linear amplifier, with a somewhat smaller shaping time constant (in the present case we choose τ = 1.5 μs), in combination with a ballistic deficit compensator. The ballistic deficit can be corrected in different ways using a Gated Integrator, a hardware correction or even a software correction. In this paper we present a comparative study of the software and hardware corrections as well as gated integration

An integrated approach towards future ballistic neck protection materials selection.

Science.gov (United States)

Breeze, John; Helliker, Mark; Carr, Debra J

2013-05-01

Ballistic protection for the neck has historically taken the form of collars attached to the ballistic vest (removable or fixed), but other approaches, including the development of prototypes incorporating ballistic material into the collar of an under body armour shirt, are now being investigated. Current neck collars incorporate the same ballistic protective fabrics as the soft armour of the remaining vest, reflecting how ballistic protective performance alone has historically been perceived as the most important property for neck protection. However, the neck has fundamental differences from the thorax in terms of anatomical vulnerability, flexibility and equipment integration, necessitating a separate solution from the thorax in terms of optimal materials selection. An integrated approach towards the selection of the most appropriate combination of materials to be used for each of the two potential designs of future neck protection has been developed. This approach requires evaluation of the properties of each potential material in addition to ballistic performance alone, including flexibility, mass, wear resistance and thermal burden. The aim of this article is to provide readers with an overview of this integrated approach towards ballistic materials selection and an update of its current progress in the development of future ballistic neck protection.

Ballistic Missile Defense in Europe

OpenAIRE

Sarihan, Ali; Bush, Amy; Summers, Lawrence; Thompson, Brent; Tomasszewski, Steven

2009-01-01

This paper will build on ballistic missile defense in Europe. In the first part, a brief historical overview will place the current public management issue into light. This is followed by a discussion of the main actors in the international debate, the problems that arise and the available options and recommendations to address missile defense. In the second part, differences between George W. Bush and Barack H. Obama will analyze under the title “Ballistic Missile Defense in Europe: Evolving...

2015 Assessment of the Ballistic Missile Defense System (BMDS)

Science.gov (United States)

2016-04-01

Director, Operational Test and Evaluation 2015 Assessment of the Ballistic Missile Defense System (BMDS...Evaluation (DOT&E) as they pertain to the Ballistic Missile Defense System (BMDS). Congress specified these requirements in the fiscal year 2002 (FY02...systems are the Ground-based Midcourse Defense (GMD), Aegis Ballistic Missile Defense (Aegis BMD), Terminal High-Altitude Area Defense (THAAD), and

Modeling terminal ballistics using blending-type spline surfaces

Science.gov (United States)

Pedersen, Aleksander; Bratlie, Jostein; Dalmo, Rune

2014-12-01

We explore using GERBS, a blending-type spline construction, to represent deform able thin-plates and model terminal ballistics. Strategies to construct geometry for different scenarios of terminal ballistics are proposed.

Ballistic resistant article, semi-finished product for and method of making a shell for a ballistic resistant article

NARCIS (Netherlands)

Harings, Jules Armand Wilhelmina; Janse, Gerardus Hubertus Anna

2013-01-01

The invention relates to a ballistic resistant article, such as a helmet (1), comprising a double curved shell in turn comprising a stack (5) of layers (6) of an oriented anti-ballistic material, the layers comprising one or more plies and having a plurality of cuts (7), the ends of which define a

Ballistic resistant article, semi-finished product for and method of making a shell for a ballistic resistant article

NARCIS (Netherlands)

Harings, Jules; Janse, Gerardus

2013-01-01

The invention relates to a ballistic resistant article, such as a helmet (1), comprising a double curved shell (2) in turn comprising a stack (5) of layers (6) of an oriented anti-ballistic material, the layers (6) comprising one or more plies and having a plurality of cuts (7), the ends of which

Magneto-ballistic transport in GaN nanowires

International Nuclear Information System (INIS)

Santoruvo, Giovanni; Allain, Adrien; Ovchinnikov, Dmitry; Matioli, Elison

2016-01-01

The ballistic filtering property of nanoscale crosses was used to investigate the effect of perpendicular magnetic fields on the ballistic transport of electrons on wide band-gap GaN heterostructures. The straight scattering-less trajectory of electrons was modified by a perpendicular magnetic field which produced a strong non-linear behavior in the measured output voltage of the ballistic filters and allowed the observation of semi-classical and quantum effects, such as quenching of the Hall resistance and manifestation of the last plateau, in excellent agreement with the theoretical predictions. A large measured phase coherence length of 190 nm allowed the observation of universal quantum fluctuations and weak localization of electrons due to quantum interference up to ∼25 K. This work also reveals the prospect of wide band-gap GaN semiconductors as a platform for basic transport and quantum studies, whose properties allow the investigation of ballistic transport and quantum phenomena at much larger voltages and temperatures than in other semiconductors.

Magneto-ballistic transport in GaN nanowires

Energy Technology Data Exchange (ETDEWEB)

Santoruvo, Giovanni, E-mail: giovanni.santoruvo@epfl.ch; Allain, Adrien; Ovchinnikov, Dmitry; Matioli, Elison, E-mail: elison.matioli@epfl.ch [Ecole Polytechnique Fédérale de Lausanne (EPFL), CH 1015 Lausanne (Switzerland)

2016-09-05

The ballistic filtering property of nanoscale crosses was used to investigate the effect of perpendicular magnetic fields on the ballistic transport of electrons on wide band-gap GaN heterostructures. The straight scattering-less trajectory of electrons was modified by a perpendicular magnetic field which produced a strong non-linear behavior in the measured output voltage of the ballistic filters and allowed the observation of semi-classical and quantum effects, such as quenching of the Hall resistance and manifestation of the last plateau, in excellent agreement with the theoretical predictions. A large measured phase coherence length of 190 nm allowed the observation of universal quantum fluctuations and weak localization of electrons due to quantum interference up to ∼25 K. This work also reveals the prospect of wide band-gap GaN semiconductors as a platform for basic transport and quantum studies, whose properties allow the investigation of ballistic transport and quantum phenomena at much larger voltages and temperatures than in other semiconductors.

A survey of spatially distributed exterior dust lead loadings in New York City

Energy Technology Data Exchange (ETDEWEB)

Caravanos, Jack [Hunter College-CUNY, School of Health Sciences (United States); Weiss, Arlene L [Environmental Medicine Inc., 263 Center Avenue, Westwood, NJ 07675 (United States); School of Medicine, New York University, NY 10016 (United States); Blaise, Marc J [Hunter College-CUNY, School of Health Sciences (United States); Jaeger, Rudolph J [Environmental Medicine Inc., 263 Center Avenue, Westwood, NJ 07675 (United States) and School of Medicine, New York University, NY 10016 (United States)

2006-02-15

This work documents ambient lead dust deposition values (lead loading) for the boroughs of New York City in 2003-2004. Currently, no regulatory standards exist for exterior concentrations of lead in settled dust. This is in contrast to the clearance and risk assessment standards that exist for interior residential dust. The reported potential for neurobehavioral toxicity and adverse cognitive development in children due to lead exposure prompts public health concerns about undocumented lead sources. Such sources may include settled dust of outdoor origin. Dust sampling throughout the five boroughs of NYC was done from the top horizontal portion of pedestrian traffic control signals (PTCS) at selected street intersections along main thoroughfares. The data (n=214 samples) show that lead in dust varies within each borough with Brooklyn having the highest median concentration (730{mu}g/ft{sup 2}), followed in descending order by Staten Island (452{mu}g/ft{sup 2}), the Bronx (382{mu}g/ft{sup 2}), Queens (198{mu}g/ft{sup 2}) and finally, Manhattan (175{mu}g/ft{sup 2}). When compared to the HUD/EPA indoor lead in dust standard of 40{mu}g/ft{sup 2}, our data show that this value is exceeded in 86% of the samples taken. An effort was made to determine the source of the lead in the dust atop of the PTCS. The lead in the dust and the yellow signage paint (which contains lead) were compared using isotopic ratio analysis. Results showed that the lead-based paint chip samples from intact signage did not isotopically match the dust wipe samples taken from the same surface. We know that exterior dust containing lead contributes to interior dust lead loading. Therefore, settled leaded dust in the outdoor environment poses a risk for lead exposure to children living in urban areas, namely, areas with elevated childhood blood lead levels and background lead dust levels from a variety of unidentified sources.

A survey of spatially distributed exterior dust lead loadings in New York City

International Nuclear Information System (INIS)

Caravanos, Jack; Weiss, Arlene L.; Blaise, Marc J.; Jaeger, Rudolph J.

2006-01-01

This work documents ambient lead dust deposition values (lead loading) for the boroughs of New York City in 2003-2004. Currently, no regulatory standards exist for exterior concentrations of lead in settled dust. This is in contrast to the clearance and risk assessment standards that exist for interior residential dust. The reported potential for neurobehavioral toxicity and adverse cognitive development in children due to lead exposure prompts public health concerns about undocumented lead sources. Such sources may include settled dust of outdoor origin. Dust sampling throughout the five boroughs of NYC was done from the top horizontal portion of pedestrian traffic control signals (PTCS) at selected street intersections along main thoroughfares. The data (n=214 samples) show that lead in dust varies within each borough with Brooklyn having the highest median concentration (730μg/ft 2 ), followed in descending order by Staten Island (452μg/ft 2 ), the Bronx (382μg/ft 2 ), Queens (198μg/ft 2 ) and finally, Manhattan (175μg/ft 2 ). When compared to the HUD/EPA indoor lead in dust standard of 40μg/ft 2 , our data show that this value is exceeded in 86% of the samples taken. An effort was made to determine the source of the lead in the dust atop of the PTCS. The lead in the dust and the yellow signage paint (which contains lead) were compared using isotopic ratio analysis. Results showed that the lead-based paint chip samples from intact signage did not isotopically match the dust wipe samples taken from the same surface. We know that exterior dust containing lead contributes to interior dust lead loading. Therefore, settled leaded dust in the outdoor environment poses a risk for lead exposure to children living in urban areas, namely, areas with elevated childhood blood lead levels and background lead dust levels from a variety of unidentified sources

Bodegas sobresuelo y estabilidad térmica interior: análisis de envolventes tradicionales y contemporáneas en Mendoza, Argentina

Directory of Open Access Journals (Sweden)

Carolina Ganem Karlen

2013-06-01

Full Text Available El control en el intercambio de flujos energéticos interior-exterior y la inercia térmica de los materiales constructivos son características claves de la envolvente de los edificios de bodegas. Esta situación es particularmente importante en el caso de los edificios construidos sobresuelo en climas con temperaturas diarias y estacionales muy variables. En el caso de que la arquitectura no provea la respuesta adecuada, indefectiblemente se recurre al consumo de energía auxiliar. La bodega S.A., ubicada en Mendoza, Argentina, consume energía auxiliar equivalente a 2.500 kW por año. Dicha bodega sobresuelo presenta dos tipos de envolvente vertical: una tradicional en adobe (λ = 0.81W/mK y otra contemporánea en chapa galvanizada sin aislación (λ = 45 W/mK. El objetivo de este trabajo es analizar los aspectos de materialidad, inercia térmica e intercambio de flujos energéticos de envolventes tradicionales y contemporáneas y, comparar los resultados obtenidos con un caso teórico de bodega subterránea. Entre los resultados obtenidos se observa que la envolvente tradicional mantiene las temperaturas interiores entre 8,5 ºC y 10 ºC por debajo de las temperaturas exteriores, mientras que los nuevos espacios con envolventes contemporáneas lo hacen solamente 3 ºC a 5 ºC por debajo de las temperaturas exteriores. En el caso de una bodega subterránea, las temperaturas estarían estables durante el año en 16,5 ºC; esto es, en verano, 20 ºC por debajo de las temperaturas exteriores.

Non-invasive nuclear device for communicating pressure inside a body to the exterior thereof

International Nuclear Information System (INIS)

Fleischmann, L.W.; Meyer, G.A.; Hittman, F.; Lyon, W.C.; Hayes, W.H. Jr.

1979-01-01

The need for a non-invasive technique for measuring the pressure in body cavities of animals or humans is recognized as highly desirable for continuous or intermittent monitoring of body conditions. The non-invasive nuclear device of the present invention is fully implantable and is fully capable of communicating pressure inside a body to the exterior to allow readout non-invasively. In its preferred form, the invention includes a housing for subcutaneous implantation with the radioactive source. An urging means such as a bellows is provided in the housing interior. The fluid pressure from a fluid pressure sensing device within the body is transmitted to the housing interior by means of a pressure-limiting fluid through a conduit. This causes the radioactive source to move against the force out of the initial or repose shielded relationship causing a proportional increase in pressure in the body portion being monitored. The radioactive output from the radioactive source corresponds to the magnitude of the pressure within the body. The housing may be securely mounted on a supporting portion of the body and the mounting serves as a radiation shield for the body. (JTA)

Quantum Mechanical Modeling of Ballistic MOSFETs

Science.gov (United States)

Svizhenko, Alexei; Anantram, M. P.; Govindan, T. R.; Biegel, Bryan (Technical Monitor)

2001-01-01

The objective of this project was to develop theory, approximations, and computer code to model quasi 1D structures such as nanotubes, DNA, and MOSFETs: (1) Nanotubes: Influence of defects on ballistic transport, electro-mechanical properties, and metal-nanotube coupling; (2) DNA: Model electron transfer (biochemistry) and transport experiments, and sequence dependence of conductance; and (3) MOSFETs: 2D doping profiles, polysilicon depletion, source to drain and gate tunneling, understand ballistic limit.

Notes on symmetric and exterior depth and annihilator numbers

Directory of Open Access Journals (Sweden)

Gesa Kampf

2008-11-01

Full Text Available We survey and compare invariants of modules over the polynomial ring and the exterior algebra. In our considerations, we focus on the depth. The exterior analogue of depth was first introduced by Aramova, Avramov and Herzog. We state similarities between the two notion of depth and exhibit their relation in the case of squarefree modules. Work of Conca, Herzog and Hibi and Trung, respectively, shows that annihilator numbers are a meaningful generalization of depth over the polynomial ring. We introduce and study annihilator numbers over the exterior algebra. Despite some minor differences in the definition, those invariants show common behavior. In both situations a positive linear combination of the annihilator numbers can be used to bound the symmetric and exterior graded Betti numbers, respectively, from above.

Ballistic transport and quantum interference in InSb nanowire devices

International Nuclear Information System (INIS)

Li Sen; Huang Guang-Yao; Guo Jing-Kun; Kang Ning; Xu Hong-Qi; Caroff, Philippe

2017-01-01

An experimental realization of a ballistic superconductor proximitized semiconductor nanowire device is a necessary step towards engineering topological quantum electronics. Here, we report on ballistic transport in InSb nanowires grown by molecular-beam epitaxy contacted by superconductor electrodes. At an elevated temperature, clear conductance plateaus are observed at zero magnetic field and in agreement with calculations based on the Landauer formula. At lower temperature, we have observed characteristic Fabry–Pérot patterns which confirm the ballistic nature of charge transport. Furthermore, the magnetoconductance measurements in the ballistic regime reveal a periodic variation related to the Fabry–Pérot oscillations. The result can be reasonably explained by taking into account the impact of magnetic field on the phase of ballistic electron’s wave function, which is further verified by our simulation. Our results pave the way for better understanding of the quantum interference effects on the transport properties of InSb nanowires in the ballistic regime as well as developing of novel device for topological quantum computations. (paper)

Ballistic negatron battery

Energy Technology Data Exchange (ETDEWEB)

Prasad, M.S.R. [Koneru Lakshmiah Univ.. Dept. of Electrical and Electronics Engineering, Green fields, Vaddeswaram (India)

2012-07-01

If we consider the Statistics there is drastic increase in dependence of batteries from year to year, due to necessity of power storage equipment at homes, power generating off grid and on grid Wind, PV systems, etc.. Where wind power is leading in renewable sector, there is a need to look at its development. Considering the scenario in India, most of the wind resource areas are far away from grid and the remaining areas which are near to grid are of low wind currents which is of no use connecting these equipment directly to grid. So, there is a need for a power storage utility to be integrated, such as the BNB (Ballistic Negatron Battery). In this situation a country like India need a battery which should be reliable, cheap and which can be industrialized. So this paper presents the concept of working, design, operation, adaptability of a Ballistic Negatron Battery. Unlike present batteries with low energy density, huge size, more weight, more charging time and low resistant to wear level, this Ballistic Negatron Battery comes with, 1) High energy storage capability (many multiples more than the present most advanced battery). 2) Very compact in size. 3) Almost negligible in weight compared to present batteries. 4) Charges with in very less time. 5) Never exhibits a wear level greater than zero. Seems like inconceivable but adoptable with simple physics. This paper will explains in detail the principle, model, design, construction and practical considerations considered in making this battery. (Author)

Cost of space-based laser ballistic missile defense.

Science.gov (United States)

Field, G; Spergel, D

1986-03-21

Orbiting platforms carrying infrared lasers have been proposed as weapons forming the first tier of a ballistic missile defense system under the President's Strategic Defense Initiative. As each laser platform can destroy a limited number of missiles, one of several methods of countering such a system is to increase the number of offensive missiles. Hence it is important to know whether the cost-exchange ratio, defined as the ratio of the cost to the defense of destroying a missile to the cost to the offense of deploying an additional missile, is greater or less than 1. Although the technology to be used in a ballistic missile defense system is still extremely uncertain, it is useful to examine methods for calculating the cost-exchange ratio. As an example, the cost of an orbiting infrared laser ballistic missile defense system employed against intercontinental ballistic missiles launched simultaneously from a small area is compared to the cost of additional offensive missiles. If one adopts lower limits to the costs for the defense and upper limits to the costs for the offense, the cost-exchange ratio comes out substantially greater than 1. If these estimates are confirmed, such a ballistic missile defense system would be unable to maintain its effectiveness at less cost than it would take to proliferate the ballistic missiles necessary to overcome it and would therefore not satisfy the President's requirements for an effective strategic defense. Although the method is illustrated by applying it to a space-based infrared laser system, it should be straightforward to apply it to other proposed systems.

Nonlinear Ballistic Transport in an Atomically Thin Material.

Science.gov (United States)

Boland, Mathias J; Sundararajan, Abhishek; Farrokhi, M Javad; Strachan, Douglas R

2016-01-26

Ultrashort devices that incorporate atomically thin components have the potential to be the smallest electronics. Such extremely scaled atomically thin devices are expected to show ballistic nonlinear behavior that could make them tremendously useful for ultrafast applications. While nonlinear diffusive electron transport has been widely reported, clear evidence for intrinsic nonlinear ballistic transport in the growing array of atomically thin conductors has so far been elusive. Here we report nonlinear electron transport of an ultrashort single-layer graphene channel that shows quantitative agreement with intrinsic ballistic transport. This behavior is shown to be distinctly different than that observed in similarly prepared ultrashort devices consisting, instead, of bilayer graphene channels. These results suggest that the addition of only one extra layer of an atomically thin material can make a significant impact on the nonlinear ballistic behavior of ultrashort devices, which is possibly due to the very different chiral tunneling of their charge carriers. The fact that we observe the nonlinear ballistic response at room temperature, with zero applied magnetic field, in non-ultrahigh vacuum conditions and directly on a readily accessible oxide substrate makes the nanogap technology we utilize of great potential for achieving extremely scaled high-speed atomically thin devices.

Effect of measurement on the ballistic-diffusive transition in turbid media.

Science.gov (United States)

Glasser, Ziv; Yaroshevsky, Andre; Barak, Bavat; Granot, Er'el; Sternklar, Shmuel

2013-10-01

The dependence of the transition between the ballistic and the diffusive regimes of turbid media on the experimental solid angle of the detection system is analyzed theoretically and experimentally. A simple model is developed which shows the significance of experimental conditions on the location of the ballistic-diffusive transition. It is demonstrated that decreasing the solid angle expands the ballistic regime; however, this benefit is bounded by the initial Gaussian beam diffraction. In addition, choosing the appropriate wavelength according to the model's principles provides another means of expanding the ballistic regime. Consequently, by optimizing the experimental conditions, it should be possible to extract the ballistic image of a tissue with a thickness of 1 cm.

Ballistic impact response of lipid membranes.

Science.gov (United States)

Zhang, Yao; Meng, Zhaoxu; Qin, Xin; Keten, Sinan

2018-03-08

Therapeutic agent loaded micro and nanoscale particles as high-velocity projectiles can penetrate cells and tissues, thereby serving as gene and drug delivery vehicles for direct and rapid internalization. Despite recent progress in developing micro/nanoscale ballistic tools, the underlying biophysics of how fast projectiles deform and penetrate cell membranes is still poorly understood. To understand the rate and size-dependent penetration processes, we present coarse-grained molecular dynamics simulations of the ballistic impact of spherical projectiles on lipid membranes. Our simulations reveal that upon impact, the projectile can pursue one of three distinct pathways. At low velocities below the critical penetration velocity, projectiles rebound off the surface. At intermediate velocities, penetration occurs after the projectile deforms the membrane into a tubular thread. At very high velocities, rapid penetration occurs through localized membrane deformation without tubulation. Membrane tension, projectile velocity and size govern which phenomenon occurs, owing to their positive correlation with the reaction force generated between the projectile and the membrane during impact. Two critical membrane tension values dictate the boundaries among the three pathways for a given system, due to the rate dependence of the stress generated in the membrane. Our findings provide broad physical insights into the ballistic impact response of soft viscous membranes and guide design strategies for drug delivery through lipid membranes using micro/nanoscale ballistic tools.

An intrinsic and exterior form of the Bianchi identities

Science.gov (United States)

Do, Thoan; Prince, Geoff

2017-09-01

We give an elegant formulation of the structure equations (of Cartan) and the Bianchi identities in terms of exterior calculus without reference to a particular basis and without the exterior covariant derivative. This approach allows both structure equations and the Bianchi identities to be expressed in terms of forms of arbitrary degree. We demonstrate the relationship with both the conventional vector version of the Bianchi identities and to the exterior covariant derivative approach. Contact manifolds, codimension one foliations and the Cartan form of classical mechanics are studied as examples of its flexibility and utility.

Ballistic quality assurance

International Nuclear Information System (INIS)

Cassol, E.; Bonnet, J.; Porcheron, D.; Mazeron, J.J.; Peiffert, D.; Alapetite, C.

2012-01-01

This review describes the ballistic quality assurance for stereotactic intracranial irradiation treatments delivered with Gamma Knife R either dedicated or adapted medical linear accelerators. Specific and periodic controls should be performed in order to check the mechanical stability for both irradiation and collimation systems. If this step remains under the responsibility of the medical physicist, it should be done in agreement with the manufacturer's technical support. At this time, there are no recent published guidelines. With technological developments, both frequency and accuracy should be assessed in each institution according to the treatment mode: single versus hypo-fractionated dose, circular collimator versus micro-multi-leaf collimators. In addition, 'end-to-end' techniques are mandatory to find the origin of potential discrepancies and to estimate the global ballistic accuracy of the delivered treatment. Indeed, they include frames, non-invasive immobilization devices, localizers, multimodal imaging for delineation and in-room positioning imaging systems. The final precision that could be reasonably achieved is more or less 1 mm. (authors)

Exterior field evaluation of new generation video motion detection systems

International Nuclear Information System (INIS)

Malone, T.P.

1988-01-01

Recent advancements in video motion detection (VMD) system design and technology have resulted in several new commercial VMD systems. Considerable interest in the new VMD systems has been generated because the systems are advertised to work effectively in exterior applications. Previous VMD systems, when used in an exterior environment, tended to have very high nuisance alarm rates due to weather conditions, wildlife activity and lighting variations. The new VMD systems advertise more advanced processing of the incoming video signal which is aimed at rejecting exterior environmental nuisance alarm sources while maintaining a high detection capability. This paper discusses the results of field testing, in an exterior environment, of two new VMD systems

La Influencia de la Temperatura Exterior sobre los Sistemas de Ventilación Natural en Grandes Atrios

Directory of Open Access Journals (Sweden)

Espina, P.

2008-09-01

Full Text Available Natural venting systems present numerous advantages opposite to the mechanical exhaust for the smoke control – a reduction in both facilities and maintenance costs–. Nevertheless, the influence of numerous factors affects significantly their efficacy: the architectural characteristics of the building, the direction and wind velocity, the proximity of tall buildings, the smoke temperature, the environmental interior and exterior temperatures, the existence of snow or ice on the ceiling, etc. All of them are important, but the influence of the environmental exterior temperature plays a decisive role. The goal of this Investigation Research was to evaluate the influence of the external temperature on the smoke movement and the hot layer descent regarding the efficacy of the natural venting systems installed for the smoke control in large atria. The analysis was developed using the ‘Fire Dynamics Simulator - FDS’ model (1, a computational fluid dynamics (CFD model of fi re-driven fluid flow for the study of fire. The results demonstrated that a design that does not contemplate this factor can turn out to be inadequate, since it has a decisive influence to guarantee human safety. The obtained results showed very significant differences about the different parameters linked to the smoke movement in an atrium.Entre las diferentes estrategias de Control y Evacuación de los Humos del Incendio, los sistemas de ventilación natural presentan numerosas ventajas frente a la ventilación mecánica – fundamentalmente una menor inversión tanto en equipos como en gastos de mantenimiento –. Sin embargo, su eficacia depende de la influencia ejercida por numerosos factores – características arquitectónicas del edificio, dirección y velocidad del viento, proximidad de edificios de gran altura, temperatura de los humos, temperatura ambiental interior, temperatura en el exterior del recinto, existencia de nieve o hielo en

A ballistic mission to fly by Comet Halley

Science.gov (United States)

Boain, R. J.; Hastrup, R. C.

1980-01-01

The paper describes the available options, ballistic trajectory opportunities, and a preliminary reference trajectory that were selected as a basis for spacecraft design studies and programmatic planning for a Halley ballistic intercept mission in 1986. The paper also presents trajectory, performance, and navigation data which support the preliminary selection.

Evaluation of the natural radioactivity in the gamma range by means of a manual dosimeter in the interior and external of housing in Cusco

International Nuclear Information System (INIS)

Warthon, J.; Olarte, A.; Valencia, J.

2014-08-01

The natural radioactivity is present in our environment and at any time the humans are exposed to this radiation type. In the 90 in Cusco city (Peru) were carried out measurements of environmental radioactivity for Umeres F. and L. Sajo, the information obtained by these investigators is valuable about the natural radioactivity in diverse places of the Cusco city; the current investigation consists on the measurement of the natural radioactivity inside and outside of the buildings in Cusco city. For 2013 and 2014 the radioactivity study has been programmed in the interior and exterior of constructions, the measures began in January 2013, to date has a considerable database. Each measures group consists of 100 tests in the interior and another similar quantity in the exterior of housing in the Cusco city; the measurement process was carried out with a manual dosimeter Geiger Muller-Zahlrohre, the average value obtained to the date is of 2.1 mSv/year which approaches to the average world value that is 2.4 mSv/year. (Author)

Space-based ballistic-missile defense

International Nuclear Information System (INIS)

Bethe, H.A.; Garwin, R.L.; Gottfried, K.; Kendall, H.W.

1984-01-01

This article, based on a forthcoming book by the Union for Concerned Scientists, focuses on the technical aspects of the issue of space-based ballistic-missile defense. After analysis, the authors conclude that the questionable performance of the proposed defense, the ease with which it could be overwhelmed or circumvented, and its potential as an antisatellite system would cause grievous damage to the security of the US if the Strategic Defense Initiative were to be pursued. The path toward greater security lies in quite another direction, they feel. Although research on ballistic-missile defense should continue at the traditional level of expenditure and within the constraints of the ABM Treaty, every effort should be made to negotiate a bilateral ban on the testing and use of space weapons. The authors think it is essential that such an agreement cover all altitudes, because a ban on high-altitude antisatellite weapons alone would not viable if directed energy weapons were developed for ballistic-missile defense. Further, the Star Wars program, unlikely ever to protect the entire nation against a nuclear attack, would nonetheless trigger a major expansion of the arms race

Ballistic food transport in toucans.

Science.gov (United States)

Baussart, Sabine; Korsoun, Leonid; Libourel, Paul-Antoine; Bels, Vincent

2009-08-01

The basic mechanism of food transport in tetrapods is lingual-based. Neognathous birds use this mechanism for exploiting a large diversity of food resources, whereas paleognathous birds use cranioinertial mechanism with or without tongue involvement. Food transport in two neognathous species of toucans (Ramphastos toco and R. vitellinus) is defined as ballistic transport mechanism. Only one transport cycle is used for moving the food from the tip of the beak to the pharynx. The food is projected between jaws with similar initial velocity in both species. At the time of release, the angle between trajectory of food position and horizontal is higher in R. vitellinus with a shorter beak than in R. toco. The tongue never makes contact with the food nor is it used to expand the buccal cavity. Tongue movement is associated with throat expansion, permitting the food to reach the entrance of the esophagus at the end of the ballistic trajectory. Selection of large food items in the diet may explain the evolutionary trend of using ballistic transport in the feeding behavior of toucans, which plays a key role in ecology of tropical forest. 2009 Wiley-Liss, Inc.

Ballistic trauma: lessons learned from iraq and afghanistan.

Science.gov (United States)

Shin, Emily H; Sabino, Jennifer M; Nanos, George P; Valerio, Ian L

2015-02-01

Management of upper extremity injuries secondary to ballistic and blast trauma can lead to challenging problems for the reconstructive surgeon. Given the recent conflicts in Iraq and Afghanistan, advancements in combat-casualty care, combined with a high-volume experience in the treatment of ballistic injuries, has led to continued advancements in the treatment of the severely injured upper extremity. There are several lessons learned that are translatable to civilian trauma centers and future conflicts. In this article, the authors provide an overview of the physics of ballistic injuries and principles in the management of such injuries through experience gained from military involvement in Iraq and Afghanistan.

Ballistic transport in graphene grown by chemical vapor deposition

International Nuclear Information System (INIS)

Calado, V. E.; Goswami, S.; Xu, Q.; Vandersypen, L. M. K.; Zhu, Shou-En; Janssen, G. C. A. M.; Watanabe, K.; Taniguchi, T.

2014-01-01

In this letter, we report the observation of ballistic transport on micron length scales in graphene synthesised by chemical vapour deposition (CVD). Transport measurements were done on Hall bar geometries in a liquid He cryostat. Using non-local measurements, we show that electrons can be ballistically directed by a magnetic field (transverse magnetic focussing) over length scales of ∼1 μm. Comparison with atomic force microscope measurements suggests a correlation between the absence of wrinkles and the presence of ballistic transport in CVD graphene

Ballistic transport in graphene grown by chemical vapor deposition

Energy Technology Data Exchange (ETDEWEB)

Calado, V. E.; Goswami, S.; Xu, Q.; Vandersypen, L. M. K., E-mail: l.m.k.vandersypen@tudelft.nl [Kavli Institute of Nanoscience, Delft University of Technology, 2600 GA Delft (Netherlands); Zhu, Shou-En; Janssen, G. C. A. M. [Micro and Nano Engineering Laboratory, Precision and Microsystems Engineering, Delft University of Technology, 2628 CD Delft (Netherlands); Watanabe, K.; Taniguchi, T. [Advanced Materials Laboratory, National Institute for Materials Science, 1-1 Namiki, Tsukuba 305-0044 (Japan)

2014-01-13

In this letter, we report the observation of ballistic transport on micron length scales in graphene synthesised by chemical vapour deposition (CVD). Transport measurements were done on Hall bar geometries in a liquid He cryostat. Using non-local measurements, we show that electrons can be ballistically directed by a magnetic field (transverse magnetic focussing) over length scales of ∼1 μm. Comparison with atomic force microscope measurements suggests a correlation between the absence of wrinkles and the presence of ballistic transport in CVD graphene.

Understanding the ballistic event : Methodology and observations relevant to ceramic armour

Science.gov (United States)

Healey, Adam

The only widely-accepted method of gauging the ballistic performance of a material is to carry out ballistic testing; due to the large volume of material required for a statistically robust test, this process is very expensive. Therefore a new test, or suite of tests, that employ widely-available and economically viable characterisation methods to screen candidate armour materials is highly desirable; in order to design such a test, more information on the armour/projectile interaction is required. This work presents the design process and results of using an adapted specimen configuration to increase the amount of information obtained from a ballistic test. By using a block of ballistic gel attached to the ceramic, the fragmentation generated during the ballistic event was captured and analysed. In parallel, quasi-static tests were carried out using ring-on-ring biaxial disc testing to investigate relationships between quasi-static and ballistic fragment fracture surfaces. Three contemporary ceramic armour materials were used to design the test and to act as a baseline; Sintox FA alumina, Hexoloy SA silicon carbide and 3M boron carbide. Attempts to analyse the post-test ballistic sample non-destructively using X-ray computed tomography (XCT) were unsuccessful due to the difference in the density of the materials and the compaction of fragments. However, the results of qualitative and quantitative fracture surface analysis using scanning electron microscopy showed similarities between the fracture surfaces of ballistic fragments at the edges of the tile and biaxial fragments; this suggests a relationship between quasi-static and ballistic fragments created away from the centre of impact, although additional research will be required to determine the reason for this. Ballistic event-induced porosity was observed and quantified on the fracture surfaces of silicon carbide samples, which decreased as distance from centre of impact increased; upon further analysis this

Missile Defense: Ballistic Missile Defense System Testing Delays Affect Delivery of Capabilities

Science.gov (United States)

2016-04-28

Page 1 GAO-16-339R Ballistic Missile Defense 441 G St. N.W. Washington, DC 20548 April 28, 2016 Congressional Committees Missile Defense... Ballistic Missile Defense System Testing Delays Affect Delivery of Capabilities For over half a century, the Department of Defense (DOD) has been...funding efforts to develop a system to detect, track, and defeat enemy ballistic missiles. The current system—the Ballistic Missile Defense System

Room-temperature ballistic energy transport in molecules with repeating units

Energy Technology Data Exchange (ETDEWEB)

Rubtsova, Natalia I.; Nyby, Clara M.; Zhang, Hong; Zhang, Boyu; Zhou, Xiao; Jayawickramarajah, Janarthanan; Burin, Alexander L.; Rubtsov, Igor V., E-mail: irubtsov@tulane.edu [Department of Chemistry, Tulane University, New Orleans, Louisiana 70118 (United States)

2015-06-07

In materials, energy can propagate by means of two limiting regimes: diffusive and ballistic. Ballistic energy transport can be fast and efficient and often occurs with a constant speed. Using two-dimensional infrared spectroscopy methods, we discovered ballistic energy transport via individual polyethylene chains with a remarkably high speed of 1440 m/s and the mean free path length of 14.6 Å in solution at room temperature. Whereas the transport via the chains occurs ballistically, the mechanism switches to diffusive with the effective transport speed of 130 m/s at the end-groups attached to the chains. A unifying model of the transport in molecules is presented with clear time separation and additivity among the transport along oligomeric fragments, which occurs ballistically, and the transport within the disordered fragments, occurring diffusively. The results open new avenues for making novel elements for molecular electronics, including ultrafast energy transporters, controlled chemical reactors, and sub-wavelength quantum nanoseparators.

Time-gated ballistic imaging using a large aperture switching beam.

Science.gov (United States)

Mathieu, Florian; Reddemann, Manuel A; Palmer, Johannes; Kneer, Reinhold

2014-03-24

Ballistic imaging commonly denotes the formation of line-of-sight shadowgraphs through turbid media by suppression of multiply scattered photons. The technique relies on a femtosecond laser acting as light source for the images and as switch for an optical Kerr gate that separates ballistic photons from multiply scattered ones. The achievable image resolution is one major limitation for the investigation of small objects. In this study, practical influences on the optical Kerr gate and image quality are discussed theoretically and experimentally applying a switching beam with large aperture (D = 19 mm). It is shown how switching pulse energy and synchronization of switching and imaging pulse in the Kerr cell influence the gate's transmission. Image quality of ballistic imaging and standard shadowgraphy is evaluated and compared, showing that the present ballistic imaging setup is advantageous for optical densities in the range of 8 ballistic imaging setup into a schlieren-type system with an optical schlieren edge.

Room-temperature ballistic energy transport in molecules with repeating units

International Nuclear Information System (INIS)

Rubtsova, Natalia I.; Nyby, Clara M.; Zhang, Hong; Zhang, Boyu; Zhou, Xiao; Jayawickramarajah, Janarthanan; Burin, Alexander L.; Rubtsov, Igor V.

2015-01-01

In materials, energy can propagate by means of two limiting regimes: diffusive and ballistic. Ballistic energy transport can be fast and efficient and often occurs with a constant speed. Using two-dimensional infrared spectroscopy methods, we discovered ballistic energy transport via individual polyethylene chains with a remarkably high speed of 1440 m/s and the mean free path length of 14.6 Å in solution at room temperature. Whereas the transport via the chains occurs ballistically, the mechanism switches to diffusive with the effective transport speed of 130 m/s at the end-groups attached to the chains. A unifying model of the transport in molecules is presented with clear time separation and additivity among the transport along oligomeric fragments, which occurs ballistically, and the transport within the disordered fragments, occurring diffusively. The results open new avenues for making novel elements for molecular electronics, including ultrafast energy transporters, controlled chemical reactors, and sub-wavelength quantum nanoseparators

Sub-ballistic behavior in the quantum kicked rotor

Energy Technology Data Exchange (ETDEWEB)

Romanelli, A. [Instituto de Fisica, Facultad de Ingenieria, Universidad de la Republica, C.C. 30, C.P. 11000, Montevideo (Uruguay)]. E-mail: alejo@fing.edu.uy; Auyuanet, A. [Instituto de Fisica, Facultad de Ingenieria, Universidad de la Republica, C.C. 30, C.P. 11000, Montevideo (Uruguay)]. E-mail: auyuanet@fing.edu.uy; Siri, R. [Instituto de Fisica, Facultad de Ingenieria, Universidad de la Republica, C.C. 30, C.P. 11000, Montevideo (Uruguay)]. E-mail: rsiri@fing.edu.uy; Micenmacher, V. [Instituto de Fisica, Facultad de Ingenieria, Universidad de la Republica, C.C. 30, C.P. 11000, Montevideo (Uruguay)]. E-mail: vmd@fing.edu.uy

2007-05-28

We study the resonances of the quantum kicked rotor subjected to an excitation that follows an aperiodic Fibonacci prescription. In such a case the secondary resonances show a sub-ballistic behavior like the quantum walk with the same aperiodic prescription for the coin. The principal resonances maintain the well-known ballistic behavior.

Sub-ballistic behavior in the quantum kicked rotor

International Nuclear Information System (INIS)

Romanelli, A.; Auyuanet, A.; Siri, R.; Micenmacher, V.

2007-01-01

We study the resonances of the quantum kicked rotor subjected to an excitation that follows an aperiodic Fibonacci prescription. In such a case the secondary resonances show a sub-ballistic behavior like the quantum walk with the same aperiodic prescription for the coin. The principal resonances maintain the well-known ballistic behavior

Electron transport in InAs/AlGaSb ballistic rectifiers

International Nuclear Information System (INIS)

Maemoto, Toshihiko; Koyama, Masatoshi; Furukawa, Masashi; Takahashi, Hiroshi; Sasa, Shigehiko; Inoue, Masataka

2006-01-01

Nonlinear transport properties of a ballistic rectifier fabricated from InAs/AlGaSb heterostructures are reported. The operation of the ballistic rectifier is based on the guidance of carriers by a square anti-dot structure. The structure was defined by electron beam lithography and wet chemical etching. The DC characteristics and magneto-transport properties of the ballistic rectifier have been measured at 77 K and 4.2 K. Rectification effects relying on the ballistic transport were observed. From the four-terminal resistance measured at low magnetic fields, we also observed magneto-resistance fluctuations corresponding to the electron trajectories and symmetry-breaking electron scattering, which are influenced by the magnetic field strength

Design and Manufacturing Process for a Ballistic Missile

Directory of Open Access Journals (Sweden)

Zaharia Sebastian Marian

2016-12-01

Full Text Available Designing a ballistic missile flight depends on the mission and the stress to which the missile is subject. Missile’s requests are determined by: the organization of components; flight regime type, engine configuration and aerodynamic performance of the rocket flight. In this paper has been developed a ballistic missile with a smooth fuselage type, 10 control surfaces, 8 directional surfaces for cornering execution, 2 for maneuvers of execution to change the angle of incidence and 4 stabilizers direction. Through the technology of gluing and clamping of the shell and the use of titanium components, mass of ballistic missile presented a significant decrease in weight and a structure with high strength.

Ballistic Anisotropic Magnetoresistance of Single-Atom Contacts.

Science.gov (United States)

Schöneberg, J; Otte, F; Néel, N; Weismann, A; Mokrousov, Y; Kröger, J; Berndt, R; Heinze, S

2016-02-10

Anisotropic magnetoresistance, that is, the sensitivity of the electrical resistance of magnetic materials on the magnetization direction, is expected to be strongly enhanced in ballistic transport through nanoscale junctions. However, unambiguous experimental evidence of this effect is difficult to achieve. We utilize single-atom junctions to measure this ballistic anisotropic magnetoresistance (AMR). Single Co and Ir atoms are deposited on domains and domain walls of ferromagnetic Fe layers on W(110) to control their magnetization directions. They are contacted with nonmagnetic tips in a low-temperature scanning tunneling microscope to measure the junction conductances. Large changes of the magnetoresistance occur from the tunneling to the ballistic regime due to the competition of localized and delocalized d-orbitals, which are differently affected by spin-orbit coupling. This work shows that engineering the AMR at the single atom level is feasible.

Diagnostics of ballistic electrons in a dc/rf hybrid capacitively coupled discharge

International Nuclear Information System (INIS)

Xu Lin; Chen, Lee; Funk, Merritt; Ranjan, Alok; Hummel, Mike; Bravenec, Ron; Sundararajan, Radha; Economou, Demetre J.; Donnelly, Vincent M.

2008-01-01

The energy distribution of ballistic electrons in a dc/rf hybrid parallel-plate capacitively coupled plasma reactor was measured. Ballistic electrons originated as secondaries produced by ion and electron bombardment of the electrodes. The energy distribution of ballistic electrons peaked at the value of the negative bias applied to the dc electrode. As that bias became more negative, the ballistic electron current on the rf substrate electrode increased dramatically. The ion current on the dc electrode also increased

QPFT operator algebras and commutative exterior differential calculus

International Nuclear Information System (INIS)

Yur'ev, D.V.

1993-01-01

The reduction of the structure theory of the operator algebras of quantum projective (sl(2, C)-invariant) field theory (QPFT operator algebras) to a commutative exterior differential calculus by means of the operation of renormalization of a pointwise product of operator fields is described. In the first section, the author introduces the concept of the operator algebra of quantum field theory and describes the operation of the renormalization of a pointwise product of operator fields. The second section is devoted to a brief exposition of the fundamentals of the structure theory of QPT operator algebras. The third section is devoted to commutative exterior differential calculus. In the fourth section, the author establishes the connection between the renormalized pointwise product of operator fields in QPFT operator algebras and the commutative exterior differential calculus. 5 refs

Towards reliable simulations of ballistic impact on concrete structures

NARCIS (Netherlands)

Khoe, Y.S.; Tyler Street, M.D.; Maravalalu Suresh,, R.S.; Weerheijm, J.

2013-01-01

Protection against weapon effects like ballistic impacts, fragmenting shells and explosions is the core business of the Explosions, Ballistics and Protection department of TNO (The Netherlands). Experimental and numerical research is performed to gain and maintain the knowledge to support the Dutch

Ballistic Jumping Drops on Superhydrophobic Surfaces via Electrostatic Manipulation.

Science.gov (United States)

Li, Ning; Wu, Lei; Yu, Cunlong; Dai, Haoyu; Wang, Ting; Dong, Zhichao; Jiang, Lei

2018-02-01

The ballistic ejection of liquid drops by electrostatic manipulating has both fundamental and practical implications, from raindrops in thunderclouds to self-cleaning, anti-icing, condensation, and heat transfer enhancements. In this paper, the ballistic jumping behavior of liquid drops from a superhydrophobic surface is investigated. Powered by the repulsion of the same kind of charges, water drops can jump from the surface. The electrostatic acting time for the jumping of a microliter supercooled drop only takes several milliseconds, even shorter than the time for icing. In addition, one can control the ballistic jumping direction precisely by the relative position above the electrostatic field. The approach offers a facile method that can be used to manipulate the ballistic drop jumping via an electrostatic field, opening the possibility of energy efficient drop detaching techniques in various applications. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Development and testing of a flexible ballistic neck protection

NARCIS (Netherlands)

Roebroeks, G.H.J.J.; Rensink, P.

2016-01-01

Sufficient ballistic protection of the neck area would significantly reduce the vulnerability of an infantry soldier. So far this protection is offered by extensions on the ballistic vest or combat helmet. However, the requirements for head agility and the various body to head positions combined

76 FR 70165 - Ballistic-Resistant Body Armor Standard Workshop

Science.gov (United States)

2011-11-10

... DEPARTMENT OF JUSTICE Office of Justice Programs [OJP (NIJ) Docket No. 1573] Ballistic-Resistant Body Armor Standard Workshop AGENCY: National Institute of Justice, DOJ. ACTION: Notice. SUMMARY: The... jointly hosting a workshop focused on NIJ Standard-0101.06, Ballistic Resistance of Body Armor, and the...

Trismus in Face Transplantation Following Ballistic Trauma.

Science.gov (United States)

Krezdorn, Nicco; Alhefzi, Muayyad; Perry, Bridget; Aycart, Mario A; Tasigiorgos, Sotirios; Bueno, Ericka M; Green, Jordan R; Pribaz, Julian J; Pomahac, Bohdan; Caterson, Edward J

2018-06-01

Trismus can be a challenging consequence of ballistic trauma to the face, and has rarely been described in the setting of face transplantation. Almost half of all current face transplant recipients in the world received transplantation to restore form and function after a ballistic injury. Here we report our experience and challenges with long standing trismus after face transplantation. We reviewed the medical records of our face transplant recipients whose indication was ballistic injury. We focused our review on trismus and assessed the pre-, peri- and postoperative planning, surgery and functional outcomes. Two patients received partial face transplantation, including the midface for ballistic trauma. Both patients suffered from impaired mouth opening, speech intelligibility, and oral competence. Severe scarring of the temporomandibular joint (TMJ) required intraoperative release in both patients, and additional total condylectomy on the left side 6 months posttransplant for 1 patient. Posttransplant, both patients achieved an improvement in mouth opening; however, there was persistent trismus. One year after transplantation, range of motion of the jaw had improved for both patients. Independent oral food intake was possible 1 year after surgery, although spillage of liquids and mixed consistency solids persisted. Speech intelligibility testing showed impairments in the immediate postoperative period, with improvement to over 85% for both patients at 1 year posttransplant. Ballistic trauma to the face and subsequent reconstructive measures can cause significant scarring and covert injuries to structures such as the TMJ, resulting in long standing trismus. Meticulous individual planning prior to interventions such as face transplantation must take these into account. We encourage intraoperative evaluation of these structures as well as peri- and postoperative treatment when necessary. Due to the nature of the primary injury, functional outcomes after face

Kinetics of diffusion-controlled and ballistically-controlled reactions

International Nuclear Information System (INIS)

Redner, S.

1995-01-01

The kinetics of diffusion-controlled two-species annihilation, A+B → O and single-species ballistically-controlled annihilation, A+A → O are investigated. For two-species annihilation, we describe the basic mechanism that leads to the formation of a coarsening mosaic of A- and B-domains. The implications of this picture on the distribution of reactants is discussed. For ballistic annihilation, dimensional analysis shows that the concentration and rms velocity decay as c∼t -α and v∼t -β , respectively, with α+β = 1 in any spatial dimension. Analysis of the Boltzmann equation for the evolution of the velocity distribution yields accurate predictions for the kinetics. New phenomena associated with discrete initial velocity distributions and with mixed ballistic and diffusive reactant motion are also discussed. (author)

Ballistic One-Dimensional InAs Nanowire Cross-Junction Interconnects.

Science.gov (United States)

Gooth, Johannes; Borg, Mattias; Schmid, Heinz; Schaller, Vanessa; Wirths, Stephan; Moselund, Kirsten; Luisier, Mathieu; Karg, Siegfried; Riel, Heike

2017-04-12

Coherent interconnection of quantum bits remains an ongoing challenge in quantum information technology. Envisioned hardware to achieve this goal is based on semiconductor nanowire (NW) circuits, comprising individual NW devices that are linked through ballistic interconnects. However, maintaining the sensitive ballistic conduction and confinement conditions across NW intersections is a nontrivial problem. Here, we go beyond the characterization of a single NW device and demonstrate ballistic one-dimensional (1D) quantum transport in InAs NW cross-junctions, monolithically integrated on Si. Characteristic 1D conductance plateaus are resolved in field-effect measurements across up to four NW-junctions in series. The 1D ballistic transport and sub-band splitting is preserved for both crossing-directions. We show that the 1D modes of a single injection terminal can be distributed into multiple NW branches. We believe that NW cross-junctions are well-suited as cross-directional communication links for the reliable transfer of quantum information as required for quantum computational systems.

Ballistic hole magnetic microscopy

NARCIS (Netherlands)

Haq, E.; Banerjee, T.; Siekman, M.H.; Lodder, J.C.; Jansen, R.

2005-01-01

A technique to study nanoscale spin transport of holes is presented: ballistic hole magnetic microscopy. The tip of a scanning tunneling microscope is used to inject hot electrons into a ferromagnetic heterostructure, where inelastic decay creates a distribution of electron-hole pairs.

Polychlorinated biphenyls in the exterior caulk of San Francisco Bay Area buildings, California, USA.

Science.gov (United States)

Klosterhaus, Susan; McKee, Lester J; Yee, Donald; Kass, Jamie M; Wong, Adam

2014-05-01

Extensive evidence of the adverse impacts of polychlorinated biphenyls (PCBs) to wildlife, domestic animals, and humans has now been documented for over 40 years. Despite the ban on production and new use of PCBs in the United States in 1979, a number of fish consumption advisories remain in effect, and there remains considerable uncertainty regarding ongoing environmental sources and management alternatives. Using a blind sampling approach, 25 caulk samples were collected from the exterior of ten buildings in the San Francisco Bay Area and analyzed for PCBs using congener-specific gas chromatography-mass spectrometry (GC-MS) and chlorine using portable X-ray fluorescence (XRF). PCBs were detected in 88% of the caulk samples collected from the study area buildings, with 40% exceeding 50 ppm. Detectable PCB concentrations ranged from 1 to 220,000 ppm. These data are consistent with previous studies in other cities that have identified relatively high concentrations of PCBs in concrete and masonry buildings built between 1950 and 1980. Portable XRF was not a good predictor of the PCB content in caulk and the results indicate that portable XRF analysis may only be useful for identifying caulk that contains low concentrations of Cl (≤ 10,000 ppm) and by extension low or no PCBs. A geographic information system-based approach was used to estimate that 10,500 kg of PCBs remain in interior and exterior caulk in buildings located in the study area, which equates to an average of 4.7 kg PCBs per building. The presence of high concentrations in the exterior caulk of currently standing buildings suggests that building caulk may be an ongoing source of PCBs to the San Francisco Bay Area environment. Further studies to expand the currently small international dataset on PCBs in caulking materials in buildings of countries that produced or imported PCBs appear justified in the context of both human health and possible ongoing environmental release. Copyright © 2014 Elsevier

Fronteras exteriores e interiores en la creación de un reino medieval: Valencia en el siglo XIII

Directory of Open Access Journals (Sweden)

Enric GUINOT RODRÍGUEZ

2009-12-01

Full Text Available RESUMEN: La génesis de las fronteras de los reinos cristianos medievales en España tiene mucho que ver con los procesos de guerra y conquista frente a al-Andalus. Éste es el caso del reino de Valencia, creado por el rey Jaime I en el año 1240 a partir de varios territorios musulmanes. Sus fronteras exteriores se crearon a partir de los límites entre cristianos y musulmanes en aquel momento y también por los pactos políticos con la corona de Castilla repartiéndose el territorio de al-Andalus. Pero estas fronteras no fueron definitivas y aún durante más de un siglo los conflictos entre la corona de Aragón y la de Castilla llevaron a cambios importantes en ellas.Por otro lado, la conquista feudal de Valencia implicó su reparto en señoríos y villas reales con la consiguiente necesidad de crear fronteras interiores para delimitarlos. Muchas veces estos límites se basaron en los existentes en época islámica, si bien fue usual que la sociedad feudal los interpretase según criterios propios y locales. Además, al estar ya en pleno siglo XIII, la organización de municipios se convirtió en la unidad básica de organización territorial, si bien existió una jerarquía entre las villas y los pueblos de su término.ABSTRACT: The origin of the borders of the medieval Christian kingdoms in Spain has much to do with the processes military and conquers over al-Andalus. This is the case of the kingdom of Valencia, created by King Jaime I in 1240 from several Muslim territories. Their outer borders were created from the boundaries between Christians and Muslims at that moment, but also by the political pacts with the crown of Castile distributing the territory of al-Andalus. But these borders were not definitive and still for more than a century the conflicts between Aragon and Castile took to important changes in them.On the other hand, the feudal conquest of Valencia implied its distribution between seigneuries and royal cities with the

Ballistic parameters and trauma potential of pistol crossbows.

Science.gov (United States)

Frank, Matthias; Schikorr, Wolfgang; Tesch, Ralf; Werner, Ronald; Hanisch, Steffen; Peters, Dieter; Ekkernkamp, Axel; Bockholdt, Britta; Seifert, Julia

2013-07-01

Hand-held pistol crossbows, which are smaller versions of conventional crossbows, have recently increased in popularity. Similar to conventional crossbows, life threatening injuries due to bolts discharged from pistol crossbows are reported in forensic and traumatological literature. While the ballistic background of conventional crossbows is comprehensively investigated, there are no investigations on the characteristic ballistic parameters (draw force, potential energy, recurve factor, kinetic energy, and efficiency) of pistol crossbows. Two hand-held pistol crossbows (Barnett Commando and Mini Cross Bow, rated draw force 362.9 N or 80 lbs) were tested. The maximum draw force was investigated using a dynamic tensile testing machine (TIRAtest 2705, TIRA GmbH). The potential energy was determined graphically by polynomial regression as area under the force-draw curve. External ballistic parameters of the bolts discharged from pistol crossbows were measured using a redundant ballistic speed measurement system (Dual-BMC 21a and Dual-LS 1000, Werner Mehl Kurzzeitmesstechnik). The average maximum draw force was 190.3 and 175.6 N for the Barnett and Mini Cross Bow, respectively. The corresponding total energy expended was 10.7 and 11 J, respectively. The recurve factor was calculated to be 0.705 and 1.044, respectively. Average bolt velocity was measured 43 up to 52 m/s. The efficiency was calculated up to 0.94. To conclude, this work provides the pending ballistic data on this special subgroup of crossbows which operate on a remarkable low kinetic energy level. Furthermore, it demonstrates that the nominal draw force pretended in the sales brochure is grossly exaggerated.

Japan and Ballistic Missile Defense

National Research Council Canada - National Science Library

Swaine, Michael

2001-01-01

Spurred by a perceived growing ballistic missile threat from within the Asia-Pacific region and requests from the United States to support research and development on components of a missile defense...

Comparative study on sintered alumina for ballistic shielding application

International Nuclear Information System (INIS)

Melo, Francisco Cristovao Lourenco de; Goncalves, Diniz Pereira

1997-01-01

This work presents a development of the armor made from special ceramic materials and kevlar. An experimental investigation was conducted to study the ballistic penetration resistance on three samples taken from sintered alumina: a commercial one and two formulations A and B made in IAE/CTA. The main differences between the two formulations was the grain size and bend resistance. The knowledge of the mechanisms during the penetration and perforation process allowed to apply a ductile composite laminate made form kevlar under the alumina to delay its rupture. The last ballistic test showed how a Weibull's modulii and other mechanical properties are able to improve ballistic penetration resistance. (author)

Ballistic heat conduction and mass disorder in one dimension

International Nuclear Information System (INIS)

Ong, Zhun-Yong; Zhang, Gang

2014-01-01

It is well-known that in the disordered harmonic chain, heat conduction is subballistic and the thermal conductivity (κ) scales asymptotically as lim L→∞ κ∝L 0.5 where L is the chain length. However, using the nonequilibrium Green's function (NEGF) method and analytical modelling, we show that there exists a critical crossover length scale (L C ) below which ballistic heat conduction (κ∝L) can coexist with mass disorder. This ballistic-to-subballistic heat conduction crossover is connected to the exponential attenuation of the phonon transmittance function Ξ i.e. Ξ(ω, L) = exp[−L/λ(ω)], where λ is the frequency-dependent attenuation length. The crossover length can be determined from the minimum attenuation length, which depends on the maximum transmitted frequency. We numerically determine the dependence of the transmittance on frequency and mass composition as well as derive a closed form estimate, which agrees closely with the numerical results. For the length-dependent thermal conductance, we also derive a closed form expression which agrees closely with numerical results and reproduces the ballistic to subballistic thermal conduction crossover. This allows us to characterize the crossover in terms of changes in the length, mass composition and temperature dependence, and also to determine the conditions under which heat conduction enters the ballistic regime. We describe how the mass composition can be modified to increase ballistic heat conduction. (paper)

Ballistic heat conduction and mass disorder in one dimension.

Science.gov (United States)

Ong, Zhun-Yong; Zhang, Gang

2014-08-20

It is well-known that in the disordered harmonic chain, heat conduction is subballistic and the thermal conductivity (κ) scales asymptotically as lim(L--> ∞) κ ∝ L(0.5) where L is the chain length. However, using the nonequilibrium Green's function (NEGF) method and analytical modelling, we show that there exists a critical crossover length scale (LC) below which ballistic heat conduction (κ ∝ L) can coexist with mass disorder. This ballistic-to-subballistic heat conduction crossover is connected to the exponential attenuation of the phonon transmittance function Ξ i.e. Ξ(ω, L) = exp[-L/λ(ω)], where λ is the frequency-dependent attenuation length. The crossover length can be determined from the minimum attenuation length, which depends on the maximum transmitted frequency. We numerically determine the dependence of the transmittance on frequency and mass composition as well as derive a closed form estimate, which agrees closely with the numerical results. For the length-dependent thermal conductance, we also derive a closed form expression which agrees closely with numerical results and reproduces the ballistic to subballistic thermal conduction crossover. This allows us to characterize the crossover in terms of changes in the length, mass composition and temperature dependence, and also to determine the conditions under which heat conduction enters the ballistic regime. We describe how the mass composition can be modified to increase ballistic heat conduction.

Transition to ballistic regime for heat transport in helium II

Energy Technology Data Exchange (ETDEWEB)

Sciacca, Michele, E-mail: michele.sciacca@unipa.it [Dipartimento Scienze Agrarie e Forestali, Università degli studi di Palermo, Viale delle Scienze, 90128 Palermo (Italy); Departament de Física, Universitat Autònoma de Barcelona, 08193 Bellaterra, Catalonia (Spain); Sellitto, Antonio, E-mail: ant.sellitto@gmail.com [Dipartimento di Matematica, Informatica ed Economia, Università della Basilicata, Campus Macchia Romana, 85100 Potenza (Italy); Jou, David, E-mail: david.jou@uab.cat [Departament de Física, Universitat Autònoma de Barcelona, 08193 Bellaterra, Catalonia (Spain); Institut d' Estudis Catalans, Carme 47, 08001 Barcelona, Catalonia (Spain)

2014-07-04

The size-dependent and flux-dependent effective thermal conductivity of narrow capillaries filled with superfluid helium is analyzed from a thermodynamic continuum perspective. The classical Landau evaluation of the effective thermal conductivity of quiescent superfluid, or the Gorter–Mellinck regime of turbulent superfluids, is extended to describe the transition to ballistic regime in narrow channels wherein the radius R is comparable to (or smaller than) the phonon mean-free path ℓ in superfluid helium. To do so, we start from an extended equation for the heat flux incorporating non-local terms, and take into consideration a heat slip flow along the walls of the tube. This leads from an effective thermal conductivity proportional to R{sup 2} (Landau regime) to another one proportional to Rℓ (ballistic regime). We consider two kinds of flows: along cylindrical pipes and along two infinite parallel plates. - Highlights: • Heat transport in counterflow helium in the ballistic regime. • The one-fluid model based on the Extended Thermodynamics is used. • The transition from the Landau regime to the ballistic regime. • The transition from quantum turbulence to ballistic regime.

Novel formulations of ballistic gelatin. 1. Rheological properties.

Science.gov (United States)

Zecheru, Teodora; Său, Ciprian; Lăzăroaie, Claudiu; Zaharia, Cătălin; Rotariu, Traian; Stănescu, Paul-Octavian

2016-06-01

Ballistic gelatin is the simulant of the human body during field tests in forensics and other related fields, due to its physical and mechanical similarities to human trunk and organs. Since the ballistic gelatin used in present has important issues to overcome, an alternative approach is the use of gelatin-polymer composites, where a key factor is the insertion of biocompatible materials, which replicate accurately the human tissues. In order to be able to obtain an improved material in terms of mechanical performances by an easy industrial-scale technology, before the verification of the ballistic parameters by shooting in agreement with military standards, one of the best and cheapest solutions is to perform a thorough check of their rheological properties, in standard conditions. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

Ballistic Transport Exceeding 28 μm in CVD Grown Graphene.

Science.gov (United States)

Banszerus, Luca; Schmitz, Michael; Engels, Stephan; Goldsche, Matthias; Watanabe, Kenji; Taniguchi, Takashi; Beschoten, Bernd; Stampfer, Christoph

2016-02-10

We report on ballistic transport over more than 28 μm in graphene grown by chemical vapor deposition (CVD) that is fully encapsulated in hexagonal boron nitride. The structures are fabricated by an advanced dry van-der-Waals transfer method and exhibit carrier mobilities of up to three million cm(2)/(Vs). The ballistic nature of charge transport is probed by measuring the bend resistance in cross- and square-shaped devices. Temperature-dependent measurements furthermore prove that ballistic transport is maintained exceeding 1 μm up to 200 K.

Simulation of depth of penetration during ballistic impact on thick ...

Indian Academy of Sciences (India)

One-dimensional discrete element model for the ballistic impact is used ... Simulation of ballistic impact process has been done using several ..... MATLAB 7.0 platform is used to simulate impact process using 1-D DEM and to perform the.

Targeting Low-Energy Ballistic Lunar Transfers

Science.gov (United States)

Parker, Jeffrey S.

2010-01-01

Numerous low-energy ballistic transfers exist between the Earth and Moon that require less fuel than conventional transfers, but require three or more months of transfer time. An entirely ballistic lunar transfer departs the Earth from a particular declination at some time in order to arrive at the Moon at a given time along a desirable approach. Maneuvers may be added to the trajectory in order to adjust the Earth departure to meet mission requirements. In this paper, we characterize the (Delta)V cost required to adjust a low-energy ballistic lunar transfer such that a spacecraft may depart the Earth at a desirable declination, e.g., 28.5(white bullet), on a designated date. This study identifies the optimal locations to place one or two maneuvers along a transfer to minimize the (Delta)V cost of the transfer. One practical application of this study is to characterize the launch period for a mission that aims to launch from a particular launch site, such as Cape Canaveral, Florida, and arrive at a particular orbit at the Moon on a given date using a three-month low-energy transfer.

A ballistics module as a part of the fire control system

Directory of Open Access Journals (Sweden)

Branka R. Luković

2013-10-01

Full Text Available This article presents a ballistics module as a part of the fire control system of weapons for fire support (mortars, artillery weapons and rocket launchers. The software is "open" with the prominence of autonomy work. It can be modulated and adapted on the user demand. Moreover, it is independent of the hardware base. Introduction: The fire control system is based on a ballistic module (BM which determines the firing data for each weapon tool in the battery. Ballistic calculations, for the given position of the target in relation to the position of tools in the given weather conditions, determine firing data (elevation, direction, timing and locating devices so that the missile seems to cause the desired effect. This paper gives the basic information about the features the BM performs and the manner of their implementation in the fire control system without going into algorithmic solution procedures. Ballistic problem in the fire control system: Ballistic calculation is based on a trajectory calculation of all kinds of projectiles (current, time-fuze, illuminating, smoke, with conventional propulsion, rocket, with built-in gas generator, etc.. Instead of previous solutions, where a trajectory calculation of the fire control system was done by approximate methods, in this BM the trajectory calculation is made by the same model with the same data as for a weapon and ammunition in the process of creating a firing table. The data used in the fire control system are made simultaneously with the preparation of firing tables for a particular tool and associated ammunition,. A modified model of particle, standardized at the NATO level, is also used. Taking into account the meteorological situation, before the trajectory calculation is done, a relative position of the target in relation to the position of the tool should be determined. A selection or loading check is carried out (possibility of reaching a given target as well as the point at which the

Experiments with Liquid Propellant Jet Ignition in a Ballistic Compressor

National Research Council Canada - National Science Library

Birk, Avi

1998-01-01

.... The apparatus consists of an inline ballistic compressor and LP injector. The rebound of the ballistic compressor piston was arrested, trapping 40 to 55 MPa of 750 to 8500 C argon for ignition of circular jets in a windowed test chamber...

Thermodynamic properties of UF sub 6 measured with a ballistic piston compressor

Science.gov (United States)

Sterritt, D. E.; Lalos, G. T.; Schneider, R. T.

1973-01-01

From experiments performed with a ballistic piston compressor, certain thermodynamic properties of uranium hexafluoride were investigated. Difficulties presented by the nonideal processes encountered in ballistic compressors are discussed and a computer code BCCC (Ballistic Compressor Computer Code) is developed to analyze the experimental data. The BCCC unfolds the thermodynamic properties of uranium hexafluoride from the helium-uranium hexafluoride mixture used as the test gas in the ballistic compressor. The thermodynamic properties deduced include the specific heat at constant volume, the ratio of specific heats for UF6, and the viscous coupling constant of helium-uranium hexafluoride mixtures.

Upstate Windows and Exteriors Information Sheet

Science.gov (United States)

Upstate Windows and Exteriors (the Company) is located in Greenville, South Carolina. The settlement involves renovation activities conducted at properties constructed prior to 1978, located in Greenville and Easley, South Carolina.

Ballistic tongue projection in a miniaturized salamander.

Science.gov (United States)

Deban, Stephen M; Bloom, Segall V

2018-05-20

Miniaturization of body size is often accompanied by peculiarities in morphology that can have functional consequences. We examined the feeding behavior and morphology of the miniaturized plethodontid salamander Thorius, one of the smallest vertebrates, to determine if its performance and biomechanics differ from those of its larger relatives. High-speed imaging and dynamics analysis of feeding at a range of temperatures show that tongue projection in Thorius macdougalli is ballistic and achieves accelerations of up to 600 G with low thermal sensitivity, indicating that tongue projection is powered by an elastic-recoil mechanism. Preceding ballistic projection is an unusual preparatory phase of tongue protrusion, which, like tongue retraction, shows lower performance and higher thermal sensitivity that are indicative of movement being powered directly by muscle shortening. The variability of tongue-projection kinematics and dynamics is comparable to larger ballistic-tongued plethodontids and reveals that Thorius is capable of modulating its tongue movements in response to prey distance. Morphological examination revealed that T. macdougalli possesses a reduced number of myofibers in the tongue muscles, a large projector muscle mass relative to tongue mass, and an unusual folding of the tongue skeleton, compared with larger relatives. Nonetheless, T. macdougalli retains the elaborated collagen aponeuroses in the projector muscle that store elastic energy and a tongue skeleton that is free of direct myofiber insertion, two features that appear to be essential for ballistic tongue projection in salamanders. © 2018 Wiley Periodicals, Inc.

Ballistic study of Tensylon®–based panels

Directory of Open Access Journals (Sweden)

L-C. Alil

2018-06-01

Full Text Available Ballistic protection is a matter of interest requested by civilian as well as military needs. The last decade has witnessed an increase in the use of light weight and efficient armour systems. These panels may be used for body protection as well as light vehicle protection against small calibres or to enhance the protection level of heavier vehicles with decreasing or maintaining their weight penalty. Ultra high molecular weight polyethylene is a material of interest for light weight armour applications. The authors designed panels made of hot–pressed Tensylon® in different configurations with thin steel sheets as a backing and shield protection. Comparison of their ballistic performance to the theory predictions reveals the improved ballistic response of the panels. In addition, a non–pressed Tensylon® panel has been tested in order to facilitate the observations of the failure mechanisms inside the panels. Even if not suitable for practical use, such non–pressed panels clearly reveal the dynamic processes at micro–scale that occur during the impact. The failure mechanisms of the material under bullet penetration are discussed based on photography, optical microscopy and scanning electron microscopy. The supposed effects of the panel pressing are discussed based on the observed difference between pressed and non–pressed structures ballistic response.

Measure Guideline: Incorporating Thick Layers of Exterior Rigid Insulation on Walls

Energy Technology Data Exchange (ETDEWEB)

Lstiburek, Joseph [Building Science Corporation, Westford, MA (United States); Baker, Peter [Building Science Corporation, Westford, MA (United States)

2015-04-01

This measure guideline provides information about the design and construction of wall assemblies that use layers of rigid exterior insulation thicker than 1-½ inches and that require a secondary cladding attachment location exterior to the insulation. The guideline is separated into several distinct sections that cover: fundamental building science principles relating to the use of exterior insulation on wall assemblies; design principles for tailoring this use to the specific project goals and requirements; and construction detailing to increase understanding about implementing the various design elements.

Ballistic protection performance of curved armor systems with or without debondings/delaminations

International Nuclear Information System (INIS)

Tan, Ping

2014-01-01

Highlights: • Influence of pre-existing defect in an armor system on its ballistic performance. • Development of finite element models for the ballistic performance of armor systems. • Prediction of the ballistic limit and back face deformation of curved armor systems. - Abstract: In order to discern how pre-existing defects such as single or multiple debondings/delaminations in a curved armor system may affect its ballistic protection performance, two-dimensional axial finite element models were generated using the commercial software ANSYS/Autodyn. The armor systems considered in this investigation are composed of boron carbide front component and Kevlar/epoxy backing component. They are assumed to be perfectly bonded at the interface without defects. The parametric study shows that for the cases considered, the maximum back face deformation of a curved armor system with or without defects is more sensitive to its curvature, material properties of the ceramic front component, and pre-existing defect size and location than the ballistic limit velocity. Additionally, both the ballistic limit velocity and maximum back face deformation are significantly affected by the backing component thickness, front/backing component thickness ratio and the number of delaminations

19 mm ballistic range: a potpourri of techniques and recipes

International Nuclear Information System (INIS)

Carpluk, G.T.

1975-01-01

The expansion of ballistic gun range facilities at LLL has introduced state-of-the-art diagnostic techniques to glovebox-enclosed ballistic guns systems. These enclosed ballistic ranges are designed for the study of one-dimensional shock phenomena in extremely toxic material such as plutonium. The extension of state-of-the-art phtographic and interferometric diagnostic systems to glovebox-enclosed gun systems introduces new design boundaries and performance criteria on optical and mechanical components. A technique for experimentally evaluating design proposals is illustrated, and several specific examples (such as, target alignment, collateral shrapnel damage, and soft recovery) are discussed

Orientation Effects in Ballistic High-Strained P-type Si Nanowire FETs

Directory of Open Access Journals (Sweden)

Hong Yu

2009-04-01

Full Text Available In order to design and optimize high-sensitivity silicon nanowire-field-effect transistor (SiNW FET pressure sensors, this paper investigates the effects of channel orientations and the uniaxial stress on the ballistic hole transport properties of a strongly quantized SiNW FET placed near the high stress regions of the pressure sensors. A discrete stress-dependent six-band k.p method is used for subband structure calculation, coupled to a two-dimensional Poisson solver for electrostatics. A semi-classical ballistic FET model is then used to evaluate the ballistic current-voltage characteristics of SiNW FETs with and without strain. Our results presented here indicate that [110] is the optimum orientation for the p-type SiNW FETs and sensors. For the ultra-scaled 2.2 nm square SiNW, due to the limit of strong quantum confinement, the effect of the uniaxial stress on the magnitude of ballistic drive current is too small to be considered, except for the [100] orientation. However, for larger 5 nm square SiNW transistors with various transport orientations, the uniaxial tensile stress obviously alters the ballistic performance, while the uniaxial compressive stress slightly changes the ballistic hole current. Furthermore, the competition of injection velocity and carrier density related to the effective hole masses is found to play a critical role in determining the performance of the nanotransistors.

Ballistic behavior of ultra-high molecular weight polyethylene composite: effect of gamma radiation

International Nuclear Information System (INIS)

Alves, Andreia L. dos Santos; Nascimento, Lucio F.C.; Suarez, Joao C. Miguez; lucio2002bol.com.br

2003-01-01

Since World War II, textile composites have been used as ballistic armor. Ultra-high molecular weight polyethylene (UHMWPE) fibers are used in the production of armor materials. As they have been developed and commercialized only recently, there is not enough information about the effect of environmental agents in the ballistic performance of UHMWPE composites. In the present work, was evaluated the ballistic behavior of composite plates manufactured with UHMWPE fibers after exposure to gamma radiation. The ballistic tests results were related to the macromolecular alterations induced by the radiation through mechanical (hardness, impact and flexure) and physicochemical (Ftir/Mir. DSC and TGA) testing. It was observed that irradiation induces changes in the UHMWPE, degrading the ballistic performance of the composite. These results are presented and discussed. (author)

Verification of models for ballistic movement time and endpoint variability.

Science.gov (United States)

Lin, Ray F; Drury, Colin G

2013-01-01

A hand control movement is composed of several ballistic movements. The time required in performing a ballistic movement and its endpoint variability are two important properties in developing movement models. The purpose of this study was to test potential models for predicting these two properties. Twelve participants conducted ballistic movements of specific amplitudes using a drawing tablet. The measured data of movement time and endpoint variability were then used to verify the models. This study was successful with Hoffmann and Gan's movement time model (Hoffmann, 1981; Gan and Hoffmann 1988) predicting more than 90.7% data variance for 84 individual measurements. A new theoretically developed ballistic movement variability model, proved to be better than Howarth, Beggs, and Bowden's (1971) model, predicting on average 84.8% of stopping-variable error and 88.3% of aiming-variable errors. These two validated models will help build solid theoretical movement models and evaluate input devices. This article provides better models for predicting end accuracy and movement time of ballistic movements that are desirable in rapid aiming tasks, such as keying in numbers on a smart phone. The models allow better design of aiming tasks, for example button sizes on mobile phones for different user populations.

Accuracy analysis of exterior orientation elements on vertical parallax in POS-supported aerial photogrammetry

Science.gov (United States)

Wu, Zhenli; Yuan, Xiuxiao

2009-10-01

This paper analyzes the effect of exterior orientation elements on vertical parallax, especially using the orientation parameters of aerial images obtained by a POS (Positioning and Orientation System) after calibration. Firstly, based on the theory of analytical relative orientation of consecutive photo connection, the exterior orientation elements can be easily translated to relative orientation elements. Then, the formula of vertical parallax can be deduced. The results of vertical parallax in left image space coordinate system are compared with the results calculated in the image coordinate system which are parallel to those of the object coordinate system. The validity and feasibility of the mathematical model are tested using two sets of actual data at different images scales. Finally, the differences between the effects of exterior orientation parameters on vertical parallax are compared using exterior orientation parameters obtained by traditional bundle block adjustment and by a POS after calibrated. And how the single element of exterior orientation effected on vertical parallax and how they worked together are analyzed. The empirical results indicate that the effects of different elements of exterior orientation on vertical parallax are different, all exterior orientation parameters can be affected by each other, so the overall effect of vertical parallax accuracy can be restricted by all exterior orientation parameters.

Ballistic edge states in Bismuth nanowires revealed by SQUID interferometry.

Science.gov (United States)

Murani, Anil; Kasumov, Alik; Sengupta, Shamashis; Kasumov, Yu A; Volkov, V T; Khodos, I I; Brisset, F; Delagrange, Raphaëlle; Chepelianskii, Alexei; Deblock, Richard; Bouchiat, Hélène; Guéron, Sophie

2017-07-05

The protection against backscattering provided by topology is a striking property. In two-dimensional insulators, a consequence of this topological protection is the ballistic nature of the one-dimensional helical edge states. One demonstration of ballisticity is the quantized Hall conductance. Here we provide another demonstration of ballistic transport, in the way the edge states carry a supercurrent. The system we have investigated is a micrometre-long monocrystalline bismuth nanowire with topological surfaces, that we connect to two superconducting electrodes. We have measured the relation between the Josephson current flowing through the nanowire and the superconducting phase difference at its ends, the current-phase relation. The sharp sawtooth-shaped phase-modulated current-phase relation we find demonstrates that transport occurs selectively along two ballistic edges of the nanowire. In addition, we show that a magnetic field induces 0-π transitions and ϕ 0 -junction behaviour, providing a way to manipulate the phase of the supercurrent-carrying edge states and generate spin supercurrents.

Monte Carlo simulation of ballistic transport in high-mobility channels

Energy Technology Data Exchange (ETDEWEB)

Sabatini, G; Marinchio, H; Palermo, C; Varani, L; Daoud, T; Teissier, R [Institut d' Electronique du Sud (CNRS UMR 5214) - Universite Montpellier II (France); Rodilla, H; Gonzalez, T; Mateos, J, E-mail: sabatini@ies.univ-montp2.f [Departamento de Fisica Aplicada - Universidad de Salamanca (Spain)

2009-11-15

By means of Monte Carlo simulations coupled with a two-dimensional Poisson solver, we evaluate directly the possibility to use high mobility materials in ultra fast devices exploiting ballistic transport. To this purpose, we have calculated specific physical quantities such as the transit time, the transit velocity, the free flight time and the mean free path as functions of applied voltage in InAs channels with different lengths, from 2000 nm down to 50 nm. In this way the transition from diffusive to ballistic transport is carefully described. We remark a high value of the mean transit velocity with a maximum of 14x10{sup 5} m/s for a 50 nm-long channel and a transit time shorter than 0.1 ps, corresponding to a cutoff frequency in the terahertz domain. The percentage of ballistic electrons and the number of scatterings as functions of distance are also reported, showing the strong influence of quasi-ballistic transport in the shorter channels.

Monte Carlo simulation of ballistic transport in high-mobility channels

International Nuclear Information System (INIS)

Sabatini, G; Marinchio, H; Palermo, C; Varani, L; Daoud, T; Teissier, R; Rodilla, H; Gonzalez, T; Mateos, J

2009-01-01

By means of Monte Carlo simulations coupled with a two-dimensional Poisson solver, we evaluate directly the possibility to use high mobility materials in ultra fast devices exploiting ballistic transport. To this purpose, we have calculated specific physical quantities such as the transit time, the transit velocity, the free flight time and the mean free path as functions of applied voltage in InAs channels with different lengths, from 2000 nm down to 50 nm. In this way the transition from diffusive to ballistic transport is carefully described. We remark a high value of the mean transit velocity with a maximum of 14x10 5 m/s for a 50 nm-long channel and a transit time shorter than 0.1 ps, corresponding to a cutoff frequency in the terahertz domain. The percentage of ballistic electrons and the number of scatterings as functions of distance are also reported, showing the strong influence of quasi-ballistic transport in the shorter channels.

[Wound Ballistics – a Brief Overview].

Science.gov (United States)

Bolliger, Stephan A; Eggert, Sebastian; Thali, Michael J

2016-02-03

Wound ballistics examines the specific effect, namely the wound profile, of bullets on the body by firing at synthetic models made of ordnance gelatine, glycerin soap and synthetic bones, validated with real cases from (battlefield) surgery and forensic pathology. Wound profile refers to the penetration depth, the bullet deformation/ fragmentation, the diameter of the permanent and the temporary wound cavity. Knowing these features and the used ammunition a surgeon can rapidly assess the amount damage within a patient. The forensic pathologist can draw conclusions as to the used ammunition based on the wound profile. By measuring of the destructive capability of different ammunition types, wound ballistics lays the foundation for guidelines concerning the maximum effect of military ammunition.

One-Dimensional Modelling of Internal Ballistics

Science.gov (United States)

Monreal-González, G.; Otón-Martínez, R. A.; Velasco, F. J. S.; García-Cascáles, J. R.; Ramírez-Fernández, F. J.

2017-10-01

A one-dimensional model is introduced in this paper for problems of internal ballistics involving solid propellant combustion. First, the work presents the physical approach and equations adopted. Closure relationships accounting for the physical phenomena taking place during combustion (interfacial friction, interfacial heat transfer, combustion) are deeply discussed. Secondly, the numerical method proposed is presented. Finally, numerical results provided by this code (UXGun) are compared with results of experimental tests and with the outcome from a well-known zero-dimensional code. The model provides successful results in firing tests of artillery guns, predicting with good accuracy the maximum pressure in the chamber and muzzle velocity what highlights its capabilities as prediction/design tool for internal ballistics.

Firearms and Ballistics

OpenAIRE

BOLTON-KING, Rachel; Schulze, Johan

2016-01-01

Chapter 7 of the book entitled 'Practical Veterinary Forensics' aims to introduce forensic veterinarians to the scientific concepts underpinning the field of firearms and ballistics. This introduction will enable practitioners to understand wound formation depending on the firearm and ammunition used. \\ud \\ud Various types of firearms, modern firing mechanisms and ammunition will be explained, together with an introduction to the physical concepts underpinning the four main constituents of th...

Gravitational time dilation and length contraction in fields exterior to ...

African Journals Online (AJOL)

Here, we use our new metric tensor exterior to a massiv3e oblate spheroid to study the gravitational phenomena of time dilation and length contraction. It turns out most profoundly that, the above phenomena hold good in the gravitational field exterior to an oblate spheroid. We then use the oblate spheroidal Earth to ...

A new experimental setup to characterize the dynamic mechanical behaviour of ballistic yarns

International Nuclear Information System (INIS)

Chevalier, C; Kerisit, C; Faderl, N; Klavzar, A; Boussu, F; Coutellier, D

2016-01-01

Fabrics have been widely used as part of ballistic protections since the 1970s and the development of new ballistic solutions made from fabrics need numerical simulations, in order to predict the performance of the ballistic protection. The performances and the induced mechanisms in ballistic fabrics during an impact depend on the weaving parameters and also on the inner parameters of the yarns used inside these structures. Thus, knowing the dynamic behaviour of yarn is essential to determine the ballistic behaviour of fabrics during an impact. Two major experimental devices exist and are used to test ballistic yarns in a dynamic uniaxial tension. The first one corresponds to the Split Hopkinson Tensile Bars device, which is commonly used to characterize the mechanical properties of materials in uniaxial tension and under high loading. The second one is the transversal impact device. The real conditions of ballistic impact can be realized with this device. Then, this paper deals with a new experimental setup developed in our laboratory and called the ‘tensile impact test for yarn’ (TITY) device. With this device, specific absorbed energy measurements of para-aramid yarns (336 Tex, Twaron ™ , 1000 filaments) have been carried out and revealed that static and dynamic properties of para-aramid are different. (paper)

Ballistic spin filtering across the ferromagnetic-semiconductor interface

Directory of Open Access Journals (Sweden)

Y.H. Li

2012-03-01

Full Text Available The ballistic spin-filter effect from a ferromagnetic metal into a semiconductor has theoretically been studied with an intention of detecting the spin polarizability of density of states in FM layer at a higher energy level. The physical model for the ballistic spin filtering across the interface between ferromagnetic metals and semiconductor superlattice is developed by exciting the spin polarized electrons into n-type AlAs/GaAs superlattice layer at a much higher energy level and then ballistically tunneling through the barrier into the ferromagnetic film. Since both the helicity-modulated and static photocurrent responses are experimentally measurable quantities, the physical quantity of interest, the relative asymmetry of spin-polarized tunneling conductance, could be extracted experimentally in a more straightforward way, as compared with previous models. The present physical model serves guidance for studying spin detection with advanced performance in the future.

Ballistic current transport studies of ferromagnetic multilayer films and tunnel junctions (invited)

International Nuclear Information System (INIS)

Rippard, W. H.; Perrella, A. C.; Buhrman, R. A.

2001-01-01

Three applications of ballistic electron microscopy are used to study, with nanometer-scale resolution, the magnetic and electronic properties of magnetic multilayer thin films and tunnel junctions. First, the capabilities of ballistic electron magnetic microscopy are demonstrated through an investigation of the switching behavior of continuous Ni 80 Fe 20 /Cu/Co trilayer films in the presence of an applied magnetic field. Next, the ballistic, hot-electron transport properties of Co films and multilayers formed by thermal evaporation and magnetron sputtering are compared, a comparison which reveals significant differences in the ballistic transmissivity of thin film multilayers formed by the two techniques. Finally, the electronic properties of thin aluminum oxide tunnel junctions formed by thermal evaporation and sputter deposition are investigated. Here the ballistic electron microscopy studies yield a direct measurement of the barrier height of the aluminum oxide barriers, a result that is invariant over a wide range of oxidation conditions. [copyright] 2001 American Institute of Physics

Method of the Determination of Exterior Orientation of Sensors in Hilbert Type Space.

Science.gov (United States)

Stępień, Grzegorz

2018-03-17

The following article presents a new isometric transformation algorithm based on the transformation in the newly normed Hilbert type space. The presented method is based on so-called virtual translations, already known in advance, of two relative oblique orthogonal coordinate systems-interior and exterior orientation of sensors-to a common, known in both systems, point. Each of the systems is translated along its axis (the systems have common origins) and at the same time the angular relative orientation of both coordinate systems is constant. The translation of both coordinate systems is defined by the spatial norm determining the length of vectors in the new Hilbert type space. As such, the displacement of two relative oblique orthogonal systems is reduced to zero. This makes it possible to directly calculate the rotation matrix of the sensor. The next and final step is the return translation of the system along an already known track. The method can be used for big rotation angles. The method was verified in laboratory conditions for the test data set and measurement data (field data). The accuracy of the results in the laboratory test is on the level of 10 -6 of the input data. This confirmed the correctness of the assumed calculation method. The method is a further development of the author's 2017 Total Free Station (TFS) transformation to several centroids in Hilbert type space. This is the reason why the method is called Multi-Centroid Isometric Transformation-MCIT. MCIT is very fast and enables, by reducing to zero the translation of two relative oblique orthogonal coordinate systems, direct calculation of the exterior orientation of the sensors.

Method of the Determination of Exterior Orientation of Sensors in Hilbert Type Space

Directory of Open Access Journals (Sweden)

Grzegorz Stępień

2018-03-01

Full Text Available The following article presents a new isometric transformation algorithm based on the transformation in the newly normed Hilbert type space. The presented method is based on so-called virtual translations, already known in advance, of two relative oblique orthogonal coordinate systems—interior and exterior orientation of sensors—to a common, known in both systems, point. Each of the systems is translated along its axis (the systems have common origins and at the same time the angular relative orientation of both coordinate systems is constant. The translation of both coordinate systems is defined by the spatial norm determining the length of vectors in the new Hilbert type space. As such, the displacement of two relative oblique orthogonal systems is reduced to zero. This makes it possible to directly calculate the rotation matrix of the sensor. The next and final step is the return translation of the system along an already known track. The method can be used for big rotation angles. The method was verified in laboratory conditions for the test data set and measurement data (field data. The accuracy of the results in the laboratory test is on the level of 10−6 of the input data. This confirmed the correctness of the assumed calculation method. The method is a further development of the author’s 2017 Total Free Station (TFS transformation to several centroids in Hilbert type space. This is the reason why the method is called Multi-Centroid Isometric Transformation—MCIT. MCIT is very fast and enables, by reducing to zero the translation of two relative oblique orthogonal coordinate systems, direct calculation of the exterior orientation of the sensors.

Ballistic Resistance of Armored Passenger Vehicles: Test Protocols and Quality Methods

Energy Technology Data Exchange (ETDEWEB)

Jeffrey M. Lacy; Robert E. Polk

2005-07-01

This guide establishes a test methodology for determining the overall ballistic resistance of the passenger compartment of assembled nontactical armored passenger vehicles (APVs). Because ballistic testing of every piece of every component of an armored vehicle is impractical, if not impossible, this guide describes a testing scheme based on statistical sampling of exposed component surface areas. Results from the test of the sampled points are combined to form a test score that reflects the probability of ballistic penetration into the passenger compartment of the vehicle.

3D high-resolution radar imaging of small body interiors

Science.gov (United States)

Sava, Paul; Asphaug, Erik

2017-10-01

Answering fundamental questions about the origin and evolution of small planetary bodies hinges on our ability to image their interior structure in detail and at high resolution (Asphaug, 2009). We often infer internal structure from surface observations, e.g. that comet 67P/Churyumov-Gerasimenko is a primordial agglomeration of cometesimals (Massironi et al., 2015). However, the interior structure is not easily accessible without systematic imaging using, e.g., radar transmission and reflection data, as suggested by the CONSERT experiment on Rosetta. Interior imaging depends on observations from multiple viewpoints, as in medical tomography.We discuss radar imaging using methodology adapted from terrestrial exploration seismology (Sava et al., 2015). We primarily focus on full wavefield methods that facilitate high quality imaging of small body interiors characterized by complex structure and large contrasts of physical properties. We consider the case of a monostatic system (co-located transmitters and receivers) operated at two frequency bands, centered around 5 and 15 MHz, from a spacecraft in slow polar orbit around a spinning comet nucleus. Assuming that the spin period is significantly (e.g. 5x) faster than the orbital period, this configuration allows repeated views from multiple directions (Safaeinili et al., 2002)Using realistic numerical experiments, we argue that (1) the comet/asteroid imaging problem is intrinsically 3D and conventional SAR methodology does not satisfy imaging, sampling and resolution requirements; (2) imaging at different frequency bands can provide information about internal surfaces (through migration) and internal volumes (through tomography); (3) interior imaging can be accomplished progressively as data are being acquired through successive orbits around the studied object; (4) imaging resolution can go beyond the apparent radar frequency band by deconvolution of the point-spread-function characterizing the imaging system; and (5

Ballistic propagation of turbulence front in tokamak edge plasmas

International Nuclear Information System (INIS)

Sugita, Satoru; Itoh, Kimitaka; Itoh, Sanae-I; Yagi, Masatoshi; Fuhr, Guillaume; Beyer, Peter; Benkadda, Sadruddin

2012-01-01

The flux-driven nonlinear simulation of resistive ballooning mode turbulence with tokamak edge geometry is performed to study the non-steady component in the edge turbulence. The large-scale and dynamical events in transport are investigated in a situation where the mean flow is suppressed. Two types of dynamics are observed. One is the radial propagation of the pulse of pressure gradient, the other is the appearance/disappearance of radially elongated global structure of turbulent heat flux. The ballistic propagation is observed in the pulse of pressure gradient, which is associated with the front of turbulent heat flux. We focus on this ballistic propagation phenomenon. Both of the bump of pressure gradient and the front of heat flux propagate inward and outward direction. It is confirmed that the strong fluctuation propagates with the pulse front. It is observed that the number of pulses going outward is close to those going inward. This ballistic phenomenon does not contradict to the turbulence spreading theory. Statistical characteristics of the ballistic propagation of pulses are evaluated and compared with scaling laws which is given by the turbulence spreading theory. It is found that they give qualitatively good agreement. (paper)

Controlling ballistic missiles: How important? How to do it?

International Nuclear Information System (INIS)

Harvey, J.R.; Rubin, U.

1992-01-01

Missiles themselves are not weapons of mass destruction; they do not give states the ability to wreak unimaginable destruction, or to radically shift the balance of power, as nuclear weapons do. Hence, the primary focus of nonproliferation efforts should remain on weapons of mass destruction, particularly nuclear weapons, rather than on one of the many possible means of delivering them. Moreover, as discussed in more detail below, advanced strike aircraft can also be effective in delivering nuclear weapons, and are generally more effective than ballistic missiles for delivering conventional or chemical ordnance. Ultimately, if the industrialized nations seriously desire to control the spread of delivery means for weapons of mass destruction, they need to consider bringing controls over ballistic missiles and advanced strike aircraft more into balance. At the same time, while efforts to control ballistic missile proliferation - centered on the Missile Technology Control Regime (MTCR) - have had some successes and could be strengthened, US policy will be most effective if it recognizes two key realities: the spread of ballistic missiles cannot be as comprehensively controlled as the spread of nuclear weapons, nor need it be as comprehensively controlled

76 FR 14589 - Defense Federal Acquisition Regulation Supplement; Repeal of Restriction on Ballistic Missile...

Science.gov (United States)

2011-03-17

...-AH18 Defense Federal Acquisition Regulation Supplement; Repeal of Restriction on Ballistic Missile...). Section 222 repeals the restriction on purchase of Ballistic Missile Defense research, development, test... Ballistic Missile Defense research, development, test, and evaluation that was required by section 222 of...

Medical Provider Ballistic Protection at Active Shooter Events.

Science.gov (United States)

Stopyra, Jason P; Bozeman, William P; Callaway, David W; Winslow, James; McGinnis, Henderson D; Sempsrott, Justin; Evans-Taylor, Lisa; Alson, Roy L

2016-01-01

There is some controversy about whether ballistic protective equipment (body armor) is required for medical responders who may be called to respond to active shooter mass casualty incidents. In this article, we describe the ongoing evolution of recommendations to optimize medical care to injured victims at such an incident. We propose that body armor is not mandatory for medical responders participating in a rapid-response capacity, in keeping with the Hartford Consensus and Arlington Rescue Task Force models. However, we acknowledge that the development and implementation of these programs may benefit from the availability of such equipment as one component of risk mitigation. Many police agencies regularly retire body armor on a defined time schedule before the end of its effective service life. Coordination with law enforcement may allow such retired body armor to be available to other public safety agencies, such as fire and emergency medical services, providing some degree of ballistic protection to medical responders at little or no cost during the rare mass casualty incident. To provide visual demonstration of this concept, we tested three "retired" ballistic vests with ages ranging from 6 to 27 years. The vests were shot at close range using police-issue 9mm, .40 caliber, .45 caliber, and 12-gauge shotgun rounds. Photographs demonstrate that the vests maintained their ballistic protection and defeated all of these rounds. 2016.

A microscopic model of ballistic-diffusive crossover

International Nuclear Information System (INIS)

Bagchi, Debarshee; Mohanty, P K

2014-01-01

Several low-dimensional systems show a crossover from diffusive to ballistic heat transport when system size is decreased. Although there is some phenomenological understanding of this crossover phenomenon at the coarse-grained level, a microscopic picture that consistently describes both the ballistic and the diffusive transport regimes has been lacking. In this work we derive a scaling form for the thermal current in a class of one dimensional systems attached to heat baths at boundaries and rigorously show that the crossover occurs when the characteristic length scale of the system competes with the system size. (paper)

Magnetic anisotropy and anisotropic ballistic conductance of thin magnetic wires

International Nuclear Information System (INIS)

Sabirianov, R.

2006-01-01

The magnetocrystalline anisotropy of thin magnetic wires of iron and cobalt is quite different from the bulk phases. The spin moment of monatomic Fe wire may be as high as 3.4 μ B , while the orbital moment as high as 0.5 μ B . The magnetocrystalline anisotropy energy (MAE) was calculated for wires up to 0.6 nm in diameter starting from monatomic wire and adding consecutive shells for thicker wires. I observe that Fe wires exhibit the change sign with the stress applied along the wire. It means that easy axis may change from the direction along the wire to perpendicular to the wire. We find that ballistic conductance of the wire depends on the direction of the applied magnetic field, i.e. shows anisotropic ballistic magnetoresistance. This effect occurs due to the symmetry dependence of the splitting of degenerate bands in the applied field which changes the number of bands crossing the Fermi level. We find that the ballistic conductance changes with applied stress. Even for thicker wires the ballistic conductance changes by factor 2 on moderate tensile stain in our 5x4 model wire. Thus, the ballistic conductance of magnetic wires changes in the applied field due to the magnetostriction. This effect can be observed as large anisotropic BMR in the experiment

Expert Meeting Report: Cladding Attachment Over Exterior Insulation

Energy Technology Data Exchange (ETDEWEB)

Baker, P. [Building Science Corporation, Somerville, MA (United States)

2013-10-01

The addition of insulation to the exterior of buildings is an effective means of increasing the thermal resistance of both wood framed walls as well as mass masonry wall assemblies. The location of the insulation to the exterior of the structure has many direct benefits including better effective R-value from reduced thermal bridging, better condensation resistance, reduced thermal stress on thestructure, as well as other commonly associated improvements such as increased air tightness and improved water management (Hutcheon 1964, Lstiburek 2007). The intent of the meeting was to review the current state of industry knowledge regarding cladding attachment over exterior insulation with a specific focus on: 1. Gravity load resistance, 2. Wind load resistance. The presentations explorethese topics from an engineering design, laboratory testing, field monitoring, as well as practical construction perspective. By bringing various groups together (who have been conduction research or have experience in this area), a more holistic review of the design limits and current code language proposals can be completed and additional gaps identified. The results of which will help informdesign standards and criteria.

Interior Space: Representation, Occupation, Well-Being and Interiority

OpenAIRE

Power, Jacqueline

2014-01-01

This article will provide an overview of space as it is understood and engaged with from within the discipline of interior design/interior architecture. Firstly, the term interior will be described. Secondly, the paper will discuss space as a general concept, before exploring what space is speifically for the interior design/interior architecture discipline. How is space understood? What does space "look" like for interuior designers/interior architects?.

Assessment and monitoring of ballistic and maximal upper-body strength qualities in athletes.

Science.gov (United States)

Young, Kieran P; Haff, G Gregory; Newton, Robert U; Gabbett, Tim J; Sheppard, Jeremy M

2015-03-01

To evaluate whether the dynamic strength index (DSI: ballistic peak force/isometric peak force) could be effectively used to guide specific training interventions and detect training-induced changes in maximal and ballistic strength. Twenty-four elite male athletes were assessed in the isometric bench press and a 45% 1-repetition-maximum (1RM) ballistic bench throw using a force plate and linear position transducer. The DSI was calculated using the peak force values obtained during the ballistic bench throw and isometric bench press. Athletes were then allocated into 2 groups as matched pairs based on their DSI and strength in the 1RM bench press. Over the 5 wk of training, athletes performed either high-load (80-100% 1RM) bench press or moderate-load (40-55% 1RM) ballistic bench throws. The DSI was sensitive to disparate training methods, with the bench-press group increasing isometric bench-press peak force (P=.035, 91% likely), and the ballistic-bench-throw group increasing bench-throw peak force to a greater extent (P≤.001, 83% likely). A significant increase (P≤.001, 93% likely) in the DSI was observed for both groups. The DSI can be used to guide specific training interventions and can detect training-induced changes in isometric bench-press and ballistic bench-throw peak force over periods as short as 5 wk.

Optimization theory for ballistic conversion

NARCIS (Netherlands)

Xie, Yanbo; Versluis, Michel; van den Berg, Albert; Eijkel, Jan C.T.

2016-01-01

The growing demand of renewable energy stimulates the exploration of new materials and methods for clean energy. We recently demonstrated a high efficiency and power density energy conversion mechanism by using jetted charged microdroplets, termed as ballistic energy conversion. Hereby, we model and

Hybrid equilibrium field coils for the ORNL TNS

International Nuclear Information System (INIS)

Peng, Y.K.M.; Strickler, D.J; Dory, R.A.

1977-01-01

In this study, we make a comparative study of the power supplies required by interior and exterior [to the toroidal field (TF) coils] equilibrium field coils that are separately appropriate for high-β, D-shaped plasmas in TNS. It is shown that the interior coils need power supplies that are an order of magnitude below those required by the exterior coils (while the latter case is much less difficult to build than the former). A hybrid EF coil concept is proposed that combines the interior and the exterior coils to retain their advantages in avoiding large interior coils while lowering the power supplied to the exterior coils by an order of magnitude

Hybrid composite laminates reinforced with Kevlar/carbon/glass woven fabrics for ballistic impact testing.

Science.gov (United States)

Randjbaran, Elias; Zahari, Rizal; Jalil, Nawal Aswan Abdul; Majid, Dayang Laila Abang Abdul

2014-01-01

Current study reported a facile method to investigate the effects of stacking sequence layers of hybrid composite materials on ballistic energy absorption by running the ballistic test at the high velocity ballistic impact conditions. The velocity and absorbed energy were accordingly calculated as well. The specimens were fabricated from Kevlar, carbon, and glass woven fabrics and resin and were experimentally investigated under impact conditions. All the specimens possessed equal mass, shape, and density; nevertheless, the layers were ordered in different stacking sequence. After running the ballistic test at the same conditions, the final velocities of the cylindrical AISI 4340 Steel pellet showed how much energy was absorbed by the samples. The energy absorption of each sample through the ballistic impact was calculated; accordingly, the proper ballistic impact resistance materials could be found by conducting the test. This paper can be further studied in order to characterise the material properties for the different layers.

Hybrid Composite Laminates Reinforced with Kevlar/Carbon/Glass Woven Fabrics for Ballistic Impact Testing

Directory of Open Access Journals (Sweden)

Elias Randjbaran

2014-01-01

Full Text Available Current study reported a facile method to investigate the effects of stacking sequence layers of hybrid composite materials on ballistic energy absorption by running the ballistic test at the high velocity ballistic impact conditions. The velocity and absorbed energy were accordingly calculated as well. The specimens were fabricated from Kevlar, carbon, and glass woven fabrics and resin and were experimentally investigated under impact conditions. All the specimens possessed equal mass, shape, and density; nevertheless, the layers were ordered in different stacking sequence. After running the ballistic test at the same conditions, the final velocities of the cylindrical AISI 4340 Steel pellet showed how much energy was absorbed by the samples. The energy absorption of each sample through the ballistic impact was calculated; accordingly, the proper ballistic impact resistance materials could be found by conducting the test. This paper can be further studied in order to characterise the material properties for the different layers.

The Anti-Ballistic Missile Treaty

International Nuclear Information System (INIS)

Platt, A.

1991-01-01

This paper reports that in late May 1972 former President Richard M. Nixon went to Moscow and signed, among other documents, a Treaty to Limit Anti-Ballistic Missile (ABM) Systems. Under this agreement, both the United States and the Soviet Union made a commitment not to build nationwide ABM defenses against the other's intercontinental and submarine-launched ballistic missiles. They agreed to limit ABM deployments to a maximum of two sites, with no more than 100 launchers per site. Thirteen of the treaty's sixteen articles are intended to prevent any deviation from this. In addition, a joint Standing Consultative Commission to monitor compliance was created. National technical means --- sophisticated monitoring devices on land, sea, and in space --- were to be the primary instruments used to monitor compliance with the treaty. The ABM Treaty was signed in conjunction with an Interim Agreement to Limit Strategic Offensive Arms

Spray Foam Exterior Insulation with Stand-Off Furring

Energy Technology Data Exchange (ETDEWEB)

Herk, Anastasia [IBACOS, Inc., Pittsburgh, PA (United States); Baker, Richard [IBACOS, Inc., Pittsburgh, PA (United States); Prahl, Duncan [IBACOS, Inc., Pittsburgh, PA (United States)

2014-03-01

IBACOS, in collaboration with GreenHomes America, was contracted by the New York State Energy Research and Development Authority to research exterior wall insulation solutions. This research investigated cost-effective deep energy retrofit (DER) solutions for improving the building shell exterior while achieving a cost-reduction goal, including reduced labor costs to reach a 50/50 split between material and labor. The strategies included exterior wall insulation plus energy upgrades as needed in the attic, mechanical and ventilation systems, and basement band joist, walls, and floors. The work can be integrated with other home improvements such as siding or window replacement. This strategy minimizes physical connections to existing wall studs, encapsulates existing siding materials (including lead paint) with spray foam, and creates a vented rain screen assembly to promote drying. GreenHomes America applied construction details created by IBACOS to a test home. 2x4 framing members were attached to the wall at band joists and top plates using 'L' clips, with spray foam insulating the wall after framing was installed. Windows were installed simultaneously with the framing, including extension jambs. The use of clips in specific areas provided the best strength potential, and 'picture framing' the spray foam held the 2x4s in place. Short-term testing was performed at this house, with monitoring equipment installed for long-term testing. Testing measurements will be provided in a later report, as well as utility impact (before and after), costs (labor and materials), construction time, standard specifications, and analysis for the exterior wall insulation strategy.

Spray Foam Exterior Insulation with Stand-Off Furring

Energy Technology Data Exchange (ETDEWEB)

Herk, Anatasia [IBACOS, Inc., Pittsburgh, PA (United States); Baker, Richard [IBACOS, Inc., Pittsburgh, PA (United States); Prahl, Duncan [IBACOS, Inc., Pittsburgh, PA (United States)

2014-03-01

IBACOS, in collaboration with GreenHomes America, was contracted by the New York State Energy Research and Development Authority to research exterior wall insulation solutions. This research investigated cost-effective deep energy retrofit (DER) solutions for improving the building shell exterior while achieving a cost-reduction goal, including reduced labor costs to reach a 50/50 split between material and labor. The strategies included exterior wall insulation plus energy upgrades as needed in the attic, mechanical and ventilation systems, and basement band joist, walls, and floors. The work can be integrated with other home improvements such as siding or window replacement. This strategy minimizes physical connections to existing wall studs, encapsulates existing siding materials (including lead paint) with spray foam, and creates a vented rain screen assembly to promote drying. GreenHomes America applied construction details created by IBACOS to a test home. 2x4 framing members were attached to the wall at band joists and top plates using "L" clips, with spray foam insulating the wall after framing was installed. Windows were installed simultaneously with the framing, including extension jambs. The use of clips in specific areas provided the best strength potential, and "picture framing" the spray foam held the 2x4s in place. Short-term testing was performed at this house, with monitoring equipment installed for long-term testing. Testing measurements will be provided in a later report, as well as utility impact (before and after), costs (labor and materials), construction time, standard specifications, and analysis for the exterior wall insulation strategy.

Ballistic Rail Gun Soft Recovery Facility

Data.gov (United States)

Federal Laboratory Consortium — The Ballistic Rail Gun Soft Recovery Facility accommodates a 155mm Howitzer, fired horizontally into a 104-foot long water trough to slow the projectile and recover...

Effects of Strength vs. Ballistic-Power Training on Throwing Performance.

Science.gov (United States)

Zaras, Nikolaos; Spengos, Konstantinos; Methenitis, Spyridon; Papadopoulos, Constantinos; Karampatsos, Giorgos; Georgiadis, Giorgos; Stasinaki, Aggeliki; Manta, Panagiota; Terzis, Gerasimos

2013-01-01

The purpose of the present study was to investigate the effects of 6 weeks strength vs. ballistic-power (Power) training on shot put throwing performance in novice throwers. Seventeen novice male shot-put throwers were divided into Strength (N = 9) and Power (n = 8) groups. The following measurements were performed before and after the training period: shot put throws, jumping performance (CMJ), Wingate anaerobic performance, 1RM strength, ballistic throws and evaluation of architectural and morphological characteristics of vastus lateralis. Throwing performance increased significantly but similarly after Strength and Power training (7.0-13.5% vs. 6.0-11.5%, respectively). Muscular strength in leg press increased more after Strength than after Power training (43% vs. 21%, respectively), while Power training induced an 8.5% increase in CMJ performance and 9.0 - 25.8% in ballistic throws. Peak power during the Wingate test increased similarly after Strength and Power training. Muscle thickness increased only after Strength training (10%, p ballistic power training in novice throwers, but with dissimilar muscular adaptations. Key pointsBallistic-power training with 30% of 1RM is equally effective in increasing shot put performance as strength training, in novice throwers, during a short training cycle of six weeks.In novice shot putters with relatively low initial muscle strength/mass, short-term strength training might be more important since it can increase both muscle strength and shot put performance.The ballistic type of power training resulted in a significant increase of the mass of type IIx muscle fibres and no change in their proportion. Thus, this type of training might be used effectively during the last weeks before competition, when the strength training load is usually reduced, in order to increase muscle power and shot put performance in novice shot putters.

Deformed exterior algebra, quons and their coherent states

International Nuclear Information System (INIS)

El Baz, M.; Hassouni, Y.

2002-08-01

We review the notion of the deformation of the exterior wedge product. This allows us to construct the deformation of the algebra of exterior forms over a vector space and also over an arbitrary manifold. We relate this approach to the generalized statistics and we study quons, as a particular case of these generalized statistics. We also give their statistical properties. A large part of the work is devoted to the problem of constructing coherent states for the deformed oscillators. We give a review of all the approaches existing in the literature concerning this point and enforce it with many examples. (author)

Geometrical optimization of a local ballistic magnetic sensor

Energy Technology Data Exchange (ETDEWEB)

Kanda, Yuhsuke; Hara, Masahiro [Graduate School of Science and Technology, Kumamoto University, 2-39-1 Kurokami, Kumamoto 860-8555 (Japan); Nomura, Tatsuya [Advanced Electronics Research Division, INAMORI Frontier Research Center, Kyushu University, 744 Motooka, Fukuoka 819-0395 (Japan); Kimura, Takashi [Advanced Electronics Research Division, INAMORI Frontier Research Center, Kyushu University, 744 Motooka, Fukuoka 819-0395 (Japan); Department of Physics, Kyushu University, 6-10-1 Hakozaki, Fukuoka 812-8581 (Japan)

2014-04-07

We have developed a highly sensitive local magnetic sensor by using a ballistic transport property in a two-dimensional conductor. A semiclassical simulation reveals that the sensitivity increases when the geometry of the sensor and the spatial distribution of the local field are optimized. We have also experimentally demonstrated a clear observation of a magnetization process in a permalloy dot whose size is much smaller than the size of an optimized ballistic magnetic sensor fabricated from a GaAs/AlGaAs two-dimensional electron gas.

Noncontact ballistic motion measurement using a fiber-optic confocal sensor

International Nuclear Information System (INIS)

Shafir, E.; Berkovic, G.; Horovitz, Y.; Appelbaum, G.; Moshe, E.; Horovitz, E.; Skutelski, A.; Werdiger, M.; Perelmutter, L.; Sudai, M.

2007-01-01

A fiber-optic confocal sensor for noncontact ballistic measurements is described. Determination of motion at velocities of 1.7 km/s with an uncertainty as small as ±0.3% is demonstrated for both a projectile and a free-surface target. The fibers detect the passage of the object at their conjugate image points created by low F/ optics. This results in an output signal comprising a train of sharp pulses each precisely identifying when the ballistic object traverses an image point. Since the ballistic object does not contact the sensor at the time of imaging, the measurements do not perturb the motion, enabling multi-fragment measurement, as well as repetitive measurements of the same object point

A simple Boltzmann transport equation for ballistic to diffusive transient heat transport

International Nuclear Information System (INIS)

Maassen, Jesse; Lundstrom, Mark

2015-01-01

Developing simplified, but accurate, theoretical approaches to treat heat transport on all length and time scales is needed to further enable scientific insight and technology innovation. Using a simplified form of the Boltzmann transport equation (BTE), originally developed for electron transport, we demonstrate how ballistic phonon effects and finite-velocity propagation are easily and naturally captured. We show how this approach compares well to the phonon BTE, and readily handles a full phonon dispersion and energy-dependent mean-free-path. This study of transient heat transport shows (i) how fundamental temperature jumps at the contacts depend simply on the ballistic thermal resistance, (ii) that phonon transport at early times approach the ballistic limit in samples of any length, and (iii) perceived reductions in heat conduction, when ballistic effects are present, originate from reductions in temperature gradient. Importantly, this framework can be recast exactly as the Cattaneo and hyperbolic heat equations, and we discuss how the key to capturing ballistic heat effects is to use the correct physical boundary conditions

Effects of Different Relative Loads on Power Performance During the Ballistic Push-up.

Science.gov (United States)

Wang, Ran; Hoffman, Jay R; Sadres, Eliahu; Bartolomei, Sandro; Muddle, Tyler W D; Fukuda, David H; Stout, Jeffrey R

2017-12-01

Wang, R, Hoffman, JR, Sadres, E, Bartolomei, S, Muddle, TWD, Fukuda, DH, and Stout, JR. Effects of different relative loads on power performance during the ballistic push-up. J Strength Cond Res 31(12): 3411-3416, 2017-The purpose of this investigation was to examine the effect of load on force and power performance during a ballistic push-up. Sixty (24.5 ± 4.3 years, 1.75 ± 0.07 m, and 80.8 ± 13.5 kg) recreationally active men who participated in this investigation completed all testing and were included in the data analysis. All participants were required to perform a 1 repetition maximum bench press, and ballistic push-ups without external load (T1), with 10% (T2) and 20% (T3) of their body mass. Ballistic push-ups during T2 and T3 were performed using a weight loaded vest. Peak and mean force, power, as well as net impulse and flight time were determined for each ballistic push-up. Peak and mean force were both significantly greater (p ballistic push-up, regardless of the participants' level of strength.

Modeling internal ballistics of gas combustion guns.

Science.gov (United States)

Schorge, Volker; Grossjohann, Rico; Schönekess, Holger C; Herbst, Jörg; Bockholdt, Britta; Ekkernkamp, Axel; Frank, Matthias

2016-05-01

Potato guns are popular homemade guns which work on the principle of gas combustion. They are usually constructed for recreational rather than criminal purposes. Yet some serious injuries and fatalities due to these guns are reported. As information on the internal ballistics of homemade gas combustion-powered guns is scarce, it is the aim of this work to provide an experimental model of the internal ballistics of these devices and to investigate their basic physical parameters. A gas combustion gun was constructed with a steel tube as the main component. Gas/air mixtures of acetylene, hydrogen, and ethylene were used as propellants for discharging a 46-mm caliber test projectile. Gas pressure in the combustion chamber was captured with a piezoelectric pressure sensor. Projectile velocity was measured with a ballistic speed measurement system. The maximum gas pressure, the maximum rate of pressure rise, the time parameters of the pressure curve, and the velocity and path of the projectile through the barrel as a function of time were determined according to the pressure-time curve. The maximum gas pressure was measured to be between 1.4 bar (ethylene) and 4.5 bar (acetylene). The highest maximum rate of pressure rise was determined for hydrogen at (dp/dt)max = 607 bar/s. The muzzle energy was calculated to be between 67 J (ethylene) and 204 J (acetylene). To conclude, this work provides basic information on the internal ballistics of homemade gas combustion guns. The risk of injury to the operator or bystanders is high, because accidental explosions of the gun due to the high-pressure rise during combustion of the gas/air mixture may occur.

Conceptual Design and Feasibility Analyses of a Robotic System for Automated Exterior Wall Painting

Directory of Open Access Journals (Sweden)

Young S. Kim

2008-11-01

Full Text Available There are approximately 6,677,000 apartment housing units in South Korea. Exterior wall painting for such multi-dwelling apartment housings in South Korea represents a typical area to which construction automation technology can be applied for improvement in safety, productivity, quality, and cost over the conventional method. The conventional exterior wall painting is costly and labor-intensive, and it especially exposes workers to significant health and safety risks. The primary objective of this study is to design a conceptual model of an exterior wall painting robot which is applicable to apartment housing construction and maintenance, and to conduct its technical?economical feasibility analyses. In this study, a design concept using a high ladder truck is proposed as the best alternative for automation of the exterior wall painting. Conclusions made in this study show that the proposed exterior wall painting robot is technically and economically feasible, and can greatly enhance safety, productivity, and quality compared to the conventional method. Finally, it is expected that the conceptual model of the exterior wall painting robot would be efficiently used in various applications in exterior wall finishing and maintenance of other architectural and civil structures such as commercial buildings, towers, and high-rise storage tanks.

Development of ballistics identification—from image comparison to topography measurement in surface metrology

International Nuclear Information System (INIS)

Song, J; Chu, W; Vorburger, T V; Thompson, R; Renegar, T B; Zheng, A; Yen, J; Silver, R; Ols, M

2012-01-01

Fired bullets and ejected cartridge cases have unique ballistics signatures left by the firearm. By analyzing the ballistics signatures, forensic examiners can trace these bullets and cartridge cases to the firearm used in a crime scene. Current automated ballistics identification systems are primarily based on image comparisons using optical microscopy. The correlation accuracy depends on image quality which is largely affected by lighting conditions. Because ballistics signatures are geometrical micro-topographies by nature, direct measurement and correlation of the surface topography is being investigated for ballistics identification. A Two-dimensional and Three-dimensional Topography Measurement and Correlation System was developed at the National Institute of Standards and Technology for certification of Standard Reference Material 2460/2461 bullets and cartridge cases. Based on this system, a prototype system for bullet signature measurement and correlation has been developed for bullet signature identifications, and has demonstrated superior correlation results. (paper)

Perancangan Interior “Interior World Center” di Surabaya

OpenAIRE

Handojo, Renita Olivia

2014-01-01

Interior World Center is a place that contain all needs and matters related to world of interior. The main purpose of Interior World Center is to give access and facilitate people in fulfill their needs that concern and correspond with interior world, that is to say with combine and integrate several interior activity into one in corporated place. Inside of this building there are several commercial space related with the interior world. The commercial spaces will support each other in order ...

Concrete shielding exterior to iron

International Nuclear Information System (INIS)

Yurista, P.; Cossairt, D.

1983-08-01

A rule of thumb at Fermilab has been to use 3 feet of concrete exterior to iron shielding. A recent design of a shield with a severe dimensional constraint has prompted a re-evaluation of this rule of thumb and has led to the following calculations of the concrete thickness required to nullify this problem. 4 references, 4 figures

Ballistic Characterization of the Scalability of Magnesium Alloy AMX602

Science.gov (United States)

2015-07-01

Magnesium Alloy AMX602 by Tyrone L Jones Weapons and Materials Research Directorate, ARL Katsuyoshi Kondoh Joining and Welding Research...formed a collaborative partnership with Osaka University Joining and Welding Research Institute (JWRI), Taber Extrusions, Epson Atmix, Pacific Sowa...Powder Metallurgy 4 5. Fabrication Procedure 4 6. Mechanical Property Analysis 5 7. Ballistic Experimental Procedures 6 8. Ballistic Experimental

Electron eigen-oscillations and ballistic modes of a stable plasma

International Nuclear Information System (INIS)

Jungwirth, K.

1976-01-01

The relation between plasma responses to singular and regular initial perturbations is established. Time scaling is introduced to separate time intervals for which eigen-oscillations (Landau solution) are dominant from such where ballistic modes prevail. The enhanced role is demonstrated of the ballistic modes for an initially perturbed field-free plasma including the phenomenon of plasma wave echoes. (author)

Measure Guideline. Incorporating Thick Layers of Exterior Rigid Insulation on Walls

Energy Technology Data Exchange (ETDEWEB)

Lstiburek, Joseph [Building Science Corporation, Westford, MA (United States); Baker, Peter [Building Science Corporation, Westford, MA (United States)

2015-04-09

This measure guideline, written by the U.S. Department of Energy’s Building America team Building Science Corporation, provides information about the design and construction of wall assemblies that use layers of rigid exterior insulation thicker than 1-½ in. and that require a secondary cladding attachment location exterior to the insulation. The guideline is separated into several distinct sections that cover: (1) fundamental building science principles relating to the use of exterior insulation on wall assemblies; (2) design principles for tailoring this use to the specific project goals and requirements; and (3) construction detailing to increase understanding about implementing the various design elements.

The application of computed tomography in wound ballistics research

International Nuclear Information System (INIS)

Tsiatis, Nick; Moraitis, Konstantinos; Papadodima, Stavroula; Spiliopoulou, Chara; Kelekis, Alexis; Kelesis, Christos; Efstathopoulos, Efstathios; Kordolaimi, Sofia; Ploussi, Agapi

2015-01-01

In wound ballistics research there is a relationship between the data that characterize a bullet and the injury resulted after shooting when it perforates the human body. The bullet path in the human body following skin perforation as well as the damaging effect cannot always be predictable as they depend on various factors such as the bullet's characteristics (velocity, distance, type of firearm and so on) and the tissue types that the bullet passes through. The purpose of this presentation is to highlight the contribution of Computed Tomography (CT) in wound ballistics research. Using CT technology and studying virtual “slices” of specific areas on scanned human bodies, allows the evaluation of density and thickness of the skin, the subcutaneous tissue, the muscles, the vital organs and the bones. Density data taken from Hounsfield units can be converted in g/ml by using the appropriate software. By evaluating the results of this study, the anatomy of the human body utilizing ballistic gel will be reproduced in order to simulate the path that a bullet follows. The biophysical analysis in wound ballistics provides another application of CT technology, which is commonly used for diagnostic and therapeutic purposes in various medical disciplines. (paper)

Ballistic-neutralized chamber transport of intense heavy ion beams

International Nuclear Information System (INIS)

Rose, D.V.; Welch, D.R.; Oliver, B.V.; Clark, R.E.; Sharp, W.M.; Friedman, A.

2001-01-01

Two-dimensional particle-in-cell simulations of intense heavy ion beams propagating in an inertial confinement fusion (ICF) reactor chamber are presented. The ballistic-neutralized transport scheme studied uses 4 GeV Pb +1 ion beams injected into a low-density, gas-filled reactor chamber and the beam is ballistically focused onto an ICF target before entering the chamber. Charge and current neutralization of the beam is provided by the low-density background gas. The ballistic-neutralized simulations include stripping of the beam ions as the beam traverses the chamber as well as ionization of the background plasma. In addition, a series of simulations are presented that explore the charge and current neutralization of the ion beam in an evacuated chamber. For this vacuum transport mode, neutralizing electrons are only drawn from sources near the chamber entrance

Evaluación de la calidad del aire interior y exterior en un jardín de niños de la Ciudad de México Evaluation of indoor and outdoor air quality of a nursery school in Mexico City

Directory of Open Access Journals (Sweden)

Marlene Cortez-Lugo

1998-09-01

Full Text Available Objetivo. Evaluar las diferencias en los niveles de ozono (O3 y bióxido de nitrógeno (NO2 en el interior y el exterior de una escuela en el suroeste de la Ciudad de México. Material y métodos. Se midieron diariamente estos contaminantes dentro y fuera del salón, de enero a abril de 1990, mediante monitoreo manual. Resultados. El NO2 adentro y afuera no sobrepasó la norma mexicana (0.21 ppm. El coeficiente de correlación entre las concentraciones máximas de NO2 de la estación de monitoreo local de la ciudad y el exterior del salón fue de 0.82 (pObjective. To evaluate the differences between indoor and outdoor ozone (O3 and nitrogen dioxide (NO2 levels at a school located in southwest Mexico City. Material and methods. Indoor and outdoor O3 and NO2 levels were measured daily between January and April 1990 by manual monitoring. Results. Indoor and outdoor concentrations of nitrogen dioxide did not surpass the Mexican standard (0.21 ppm. The correlation coefficient between maximum NO2 concentrations measured by the city’s local monitoring station and those measured outside the classroom was 0.82 (p< 0.001. Regarding ozone, its maximum outdoor concentration was 0.29 ppm and indoor concentrations were on average below 0.06 ppm (maximum = 0.17 ppm. The indoor/outdoor correlation coefficient was 0.72, and for every 1.7 ppm outside, there was 1.0 ppm inside (p< 0.05 Conclusions. Since the highest outdoors O3 concentrations were observed between 11:00 and 14:00 hrs, it is recommendable to have recess before this time.

Numerical experiments using CHIEF to treat the nonuniqueness in solving acoustic axisymmetric exterior problems via boundary integral equations

Directory of Open Access Journals (Sweden)

Adel A.K. Mohsen

2010-07-01

Full Text Available The problem of nonuniqueness (NU of the solution of exterior acoustic problems via boundary integral equations is discussed in this article. The efficient implementation of the CHIEF (Combined Helmholtz Integral Equations Formulation method to axisymmetric problems is studied. Interior axial fields are used to indicate the solution error and to select proper CHIEF points. The procedure makes full use of LU-decomposition as well as the forward solution derived in the solution. Implementations of the procedure for hard spheres are presented. Accurate results are obtained up to a normalised radius of ka = 20.983, using only one CHIEF point. The radiation from a uniformly vibrating sphere is also considered. Accurate results for ka up to 16.927 are obtained using two CHIEF points.

Excavationless Exterior Foundation Insulation Field Study

Energy Technology Data Exchange (ETDEWEB)

Schirber, T.; Mosiman, G.; Ojczyk, C.

2014-10-01

Building science research supports installing exterior (soil side) foundation insulation as the optimal method to enhance the hygrothermal performance of new homes. With exterior foundation insulation, water management strategies are maximized while insulating the basement space and ensuring a more even temperature at the foundation wall. However, such an approach can be very costly and disruptive when applied to an existing home, requiring deep excavation around the entire house. The NorthernSTAR Building America Partnership team implemented an innovative, minimally invasive foundation insulation upgrade technique on an existing home. The approach consisted of using hydrovac excavation technology combined with a liquid insulating foam. The team was able to excavate a continuous 4" wide by 4' to 5' deep trench around the entire house, 128 linear feet, except for one small part under the stoop that was obstructed with concrete debris. The combination pressure washer and vacuum extraction technology also enabled the elimination of large trenches and soil stockpiles normally produced by backhoe excavation. The resulting trench was filled with liquid insulating foam, which also served as a water-control layer of the assembly. The insulation was brought above grade using a liquid foam/rigid foam hybrid system and terminated at the top of the rim joist. Cost savings over the traditional excavation process ranged from 23% to 50%. The excavationless process could result in even greater savings since replacement of building structures, exterior features, utility meters, and landscaping would be minimal or non-existent in an excavationless process.

Excavationless Exterior Foundation Insulation Field Study

Energy Technology Data Exchange (ETDEWEB)

Schirber, T. [NorthernSTAR, Minneaplolis, MN (United States); Mosiman, G. [NorthernSTAR, Minneaplolis, MN (United States); Ojczyk, C. [NorthernSTAR, Minneaplolis, MN (United States)

2014-09-01

Building science research supports installing exterior (soil side) foundation insulation as the optimal method to enhance the hygrothermal performance of new homes. With exterior foundation insulation, water management strategies are maximized while insulating the basement space and ensuring a more even temperature at the foundation wall. However, such an approach can be very costly and disruptive when applied to an existing home, requiring deep excavation around the entire house. The NorthernSTAR Building America Partnership team implemented an innovative, minimally invasive foundation insulation upgrade technique on an existing home. The approach consisted of using hydrovac excavation technology combined with liquid insulating foam. The team was able to excavate a continuous 4 inches wide by 4 feet to 5 feet deep trench around the entire house, 128 linear feet, except for one small part under the stoop that was obstructed with concrete debris. The combination pressure washer and vacuum extraction technology also enabled the elimination of large trenches and soil stockpiles normally produced by backhoe excavation. The resulting trench was filled with liquid insulating foam, which also served as a water-control layer of the assembly. The insulation was brought above grade using a liquid foam/rigid foam hybrid system and terminated at the top of the rim joist. Cost savings over the traditional excavation process ranged from 23% to 50%. The excavationless process could result in even greater savings since replacement of building structures, exterior features, utility meters, and landscaping would be minimal or non-existent in an excavationless process.

Diseño de un armario eléctrico para alumbrado exterior

OpenAIRE

Vermeil, Bastien

2009-01-01

El Proyecto tiene como objetivo el diseño de un armario eléctrico de alumbrado exterior que proporcione un valor añadido a los existentes actualmente. Este producto, diseñado para proteger los sistemas de alimentación y control de las instalaciones eléctricas, guardará esta función principal, tendrá un diseño exterior nuevo, y nuevas funcionalidades. Ahora, estas instalaciones permiten de alimentar la calle, los alumbradores exteriores en electricidad y gestionar las diferentes líneas desd...

Results of a Round Robin ballistic load sensing headform test series

NARCIS (Netherlands)

Philippens, M.A.G.; Anctil, B.; Markwardt, K.C.

2014-01-01

The majority of methods to assess the behind armour blunt trauma (BABT) risk for ballistic helmets is based on plastic deformable headforms. An alternative, the Ballistic Load Sensing Headform (BLSH) can record the dynamic contact force between helmet back face and the skull. Helmet BABT methods are

Ballistic superconductivity in semiconductor nanowires

Science.gov (United States)

Zhang, Hao; Gül, Önder; Conesa-Boj, Sonia; Nowak, Michał P.; Wimmer, Michael; Zuo, Kun; Mourik, Vincent; de Vries, Folkert K.; van Veen, Jasper; de Moor, Michiel W. A.; Bommer, Jouri D. S.; van Woerkom, David J.; Car, Diana; Plissard, Sébastien R; Bakkers, Erik P.A.M.; Quintero-Pérez, Marina; Cassidy, Maja C.; Koelling, Sebastian; Goswami, Srijit; Watanabe, Kenji; Taniguchi, Takashi; Kouwenhoven, Leo P.

2017-01-01

Semiconductor nanowires have opened new research avenues in quantum transport owing to their confined geometry and electrostatic tunability. They have offered an exceptional testbed for superconductivity, leading to the realization of hybrid systems combining the macroscopic quantum properties of superconductors with the possibility to control charges down to a single electron. These advances brought semiconductor nanowires to the forefront of efforts to realize topological superconductivity and Majorana modes. A prime challenge to benefit from the topological properties of Majoranas is to reduce the disorder in hybrid nanowire devices. Here we show ballistic superconductivity in InSb semiconductor nanowires. Our structural and chemical analyses demonstrate a high-quality interface between the nanowire and a NbTiN superconductor that enables ballistic transport. This is manifested by a quantized conductance for normal carriers, a strongly enhanced conductance for Andreev-reflecting carriers, and an induced hard gap with a significantly reduced density of states. These results pave the way for disorder-free Majorana devices. PMID:28681843

Molecular Dynamics Studies on Ballistic Thermal Resistance of Graphene Nano-Junctions

International Nuclear Information System (INIS)

Yao Wen-Jun; Cao Bing-Yang

2015-01-01

Ballistic thermal resistance of graphene nano-junctions is investigated using non-equilibrium molecular dynamics simulation. The simulation system is consisted of two symmetrical trapezoidal or rectangular graphene nano-ribbons (GNRs) and a connecting nanoscale constriction in between. From the simulated temperature profile, a big temperature jump resulted from the constriction is found, which is proportional to the heat current and corresponds to a local ballistic thermal resistance. Fixing the constriction width and the length of GNRs, this ballistic thermal resistance is independent of the width of the GNRs bottom layer, i.e., the convex angle. But interestingly, this thermal resistance has obvious size effect. It is inversely proportional to the constriction width and will disappear with the constriction being wider. Moreover, based on the phonon dynamics theory, a theoretical model of the ballistic thermal resistance in two-dimensional nano-systems is developed, which gives a good explanation on microcosmic level and agrees well with the simulation result quantitatively and qualitatively. (paper)

Effect of ballistic electrons on ultrafast thermomechanical responses of a thin metal film

International Nuclear Information System (INIS)

Xiong Qi-lin; Tian Xin

2017-01-01

The ultrafast thermomechanical coupling problem in a thin gold film irradiated by ultrashort laser pulses with different electron ballistic depths is investigated via the ultrafast thermoelasticity model. The solution of the problem is obtained by solving finite element governing equations. The comparison between the results of ultrafast thermomechanical coupling responses with different electron ballistic depths is made to show the ballistic electron effect. It is found that the ballistic electrons have a significant influence on the ultrafast thermomechanical coupling behaviors of the gold thin film and the best laser micromachining results can be achieved by choosing the specific laser technology (large or small ballistic range). In addition, the influence of simplification of the ultrashort laser pulse source on the results is studied, and it is found that the simplification has a great influence on the thermomechanical responses, which implies that care should be taken when the simplified form of the laser source term is applied as the Gaussian heat source. (paper)

Self-diffusion and solute diffusion in alloys under irradiation: Influence of ballistic jumps

International Nuclear Information System (INIS)

Roussel, Jean-Marc; Bellon, Pascal

2002-01-01

We have studied the influence of ballistic jumps on thermal and total diffusion of solvent and solute atoms in dilute fcc alloys under irradiation. For the diffusion components that result from vacancy migration, we introduce generalized five-frequency models, and show that ballistic jumps produce decorrelation effects that have a moderate impact on self-diffusion but that can enhance or suppress solute diffusion by several orders of magnitude. These could lead to new irradiation-induced transformations, especially in the case of subthreshold irradiation conditions. We also show that the mutual influence of thermal and ballistic jumps results in a nonadditivity of partial diffusion coefficients: the total diffusion coefficient under irradiation may be less than the sum of the thermal and ballistic diffusion coefficients. These predictions are confirmed by kinetic Monte Carlo simulations. Finally, it is shown that the method introduced here can be extended to take into account the effect of ballistic jumps on the diffusion of dumbbell interstitials in dilute alloys

Heat pump having improved defrost system

Science.gov (United States)

Chen, F.C.; Mei, V.C.; Murphy, R.W.

1998-12-08

A heat pump system includes, in an operable relationship for transferring heat between an exterior atmosphere and an interior atmosphere via a fluid refrigerant: a compressor; an interior heat exchanger; an exterior heat exchanger; an accumulator; and means for heating the accumulator in order to defrost the exterior heat exchanger. 2 figs.

Modeled heating and surface erosion comparing motile (gas borne) and stationary (surface coating) inert particle additives

International Nuclear Information System (INIS)

Buckingham, A.C.; Siekhaus, W.J.

1982-01-01

The unsteady, non-similar, chemically reactive, turbulent boundary layer equations are modified for gas plus dispersed solid particle mixtures, for gas phase turbulent combustion reactions and for heterogeneous gas-solid surface erosive reactions. The exterior (ballistic core) edge boundary conditions for the solutions are modified to include dispersed particle influences on core propellant combustion-generated turbulence levels, combustion reactants and products, and reaction-induced, non-isentropic mixture states. The wall surface (in this study it is always steel) is considered either bare or coated with a fixed particle coating which is conceptually non-reactive, insulative, and non-ablative. Two families of solutions are compared. These correspond to: (1) consideration of gas-borne, free-slip, almost spontaneously mobile (motile) solid particle additives which influence the turbulent heat transfer at the uncoated steel surface and, in contrast, (2) consideration of particle-free, gas phase turbulent heat transfer to the insulated surface coated by stationary particles. Significant differences in erosive heat transfer are found in comparing the two families of solutions over a substantial range of interior ballistic flow conditions. The most effective influences on reducing erosive heat transfer appear to favor mobile, gas-borne particle additives

Low-temperature ballistic transport in nanoscale epitaxial graphene cross junctions

OpenAIRE

Weingart, S.; Bock, C.; Kunze, U.; Speck, F.; Seyller, Th.; Ley, L.

2009-01-01

We report on the observation of inertial-ballistic transport in nanoscale cross junctions fabricated from epitaxial graphene grown on SiC(0001). Ballistic transport is indicated by a negative bend resistance of R12,43 ~ 170 ohm which is measured in a non-local, four-terminal configuration at 4.2 K and which vanishes as the temperature is increased above 80 K.

Micro-Doppler Feature Extraction and Recognition Based on Netted Radar for Ballistic Targets

Directory of Open Access Journals (Sweden)

Feng Cun-qian

2015-12-01

Full Text Available This study examines the complexities of using netted radar to recognize and resolve ballistic midcourse targets. The application of micro-motion feature extraction to ballistic mid-course targets is analyzed, and the current status of application and research on micro-motion feature recognition is concluded for singlefunction radar networks such as low- and high-resolution imaging radar networks. Advantages and disadvantages of these networks are discussed with respect to target recognition. Hybrid-mode radar networks combine low- and high-resolution imaging radar and provide a specific reference frequency that is the basis for ballistic target recognition. Main research trends are discussed for hybrid-mode networks that apply micromotion feature extraction to ballistic mid-course targets.

Injury, Interiority, and Isolation in Men's Suicidality.

Science.gov (United States)

Oliffe, John L; Creighton, Genevieve; Robertson, Steve; Broom, Alex; Jenkins, Emily K; Ogrodniczuk, John S; Ferlatte, Olivier

2017-07-01

Men's high suicide rates have been linked to individual risk factors including history of being abused as a child, single marital status, and financial difficulties. While it has also been suggested that the normative influences of hegemonic masculinities are implicated in men's suicide, the gendered experiences of male suicidality are poorly understood. In the current photovoice study, 20 men who previously had suicidal thoughts, plans, and/or attempts were interviewed as a means to better understanding the connections between masculinities and their experiences of suicidality. The study findings revealed injury, interiority, and isolation as interconnected themes characterizing men's suicidality. Injury comprised an array of childhood and/or cumulative traumas that fueled men's ruminating thoughts inhibiting recovery and limiting hopes for improved life quality. In attempting to blunt these traumas, many men described self-injuring through the overuse of alcohol and other drugs. The interiority theme revealed how suicidal thoughts can fuel hopelessness amid summonsing remedies from within. The challenges to self-manage, especially when experiencing muddled thinking and negative thought were evident, and led some participants to summons exterior resources to counter suicidality. Isolation included separateness from others, and was linked to abandonment issues and not having a job and/or partner. Self-isolating also featured as a protection strategy to avoid troubling others and/or reducing exposure to additional noxious stimuli. The study findings suggest multiple intervention points and strategies, the majority of which are premised on promoting men's social connectedness. The destigmatizing value of photovoice methods is also discussed.

Are certain fractures at increased risk for compartment syndrome after civilian ballistic injury?

Science.gov (United States)

Meskey, Thomas; Hardcastle, John; O'Toole, Robert V

2011-11-01

Compartment syndrome after ballistic fracture is uncommon but potentially devastating. Few data are available to help guide clinicians regarding risk factors for developing compartment syndrome after ballistic fractures. Our primary hypothesis was that ballistic fractures of certain bones would be at higher risk for development of compartment syndrome. A retrospective review at a Level I trauma center from 2001 through 2007 yielded 650 patients with 938 fractures resulting from gunshots. We reviewed all operative notes, clinic notes, discharge summaries, and data from our prospective trauma database. Cases in which the attending orthopedic surgeon diagnosed compartment syndrome and performed fasciotomy were considered cases with compartment syndrome. We excluded all prophylactic fasciotomies. Univariate analyses were conducted to identify risk factors associated with development of compartment syndrome. Twenty-six (2.8%) of the 938 fractures were associated with compartment syndrome. Only fibular (11.6%) and tibial (11.4%) fractures had incidence significantly higher than baseline for all ballistic fractures (p Ballistic fractures of the fibula and tibia are at increased risk for development of compartment syndrome over other ballistic fractures. We recommend increased vigilance when treating these injuries, particularly if the fracture is in the proximal aspect of the bone or is associated with vascular injury.

Ballistic Missile Defense

OpenAIRE

Mayer, Michael

2011-01-01

At the 2010 NATO summit in Lisbon, the alliance decided to move forward on the development of a territorial ballistic missile defense (BMD) system and explore avenues for cooperation with Russia in this endeavor. Substantial progress on BMD has been made over the past decade, but some questions remain regarding the ultimate strategic utility of such a system and whether its benefi ts outweigh the possible opportunity costs. Missile defense has been a point of contention between the US and its...

Potentiation Effects of Half-Squats Performed in a Ballistic or Nonballistic Manner.

Science.gov (United States)

Suchomel, Timothy J; Sato, Kimitake; DeWeese, Brad H; Ebben, William P; Stone, Michael H

2016-06-01

This study examined and compared the acute effects of ballistic and nonballistic concentric-only half-squats (COHSs) on squat jump performance. Fifteen resistance-trained men performed a squat jump 2 minutes after a control protocol or 2 COHSs at 90% of their 1 repetition maximum (1RM) COHS performed in a ballistic or nonballistic manner. Jump height (JH), peak power (PP), and allometrically scaled peak power (PPa) were compared using three 3 × 2 repeated-measures analyses of variance. Statistically significant condition × time interaction effects existed for JH (p = 0.037), PP (p = 0.041), and PPa (p = 0.031). Post hoc analysis revealed that the ballistic condition produced statistically greater JH (p = 0.017 and p = 0.036), PP (p = 0.031 and p = 0.026), and PPa (p = 0.024 and p = 0.023) than the control and nonballistic conditions, respectively. Small effect sizes for JH, PP, and PPa existed during the ballistic condition (d = 0.28-0.44), whereas trivial effect sizes existed during the control (d = 0.0-0.18) and nonballistic (d = 0.0-0.17) conditions. Large statistically significant relationships existed between the JH potentiation response and the subject's relative back squat 1RM (r = 0.520; p = 0.047) and relative COHS 1RM (r = 0.569; p = 0.027) during the ballistic condition. In addition, large statistically significant relationship existed between JH potentiation response and the subject's relative back squat strength (r = 0.633; p = 0.011), whereas the moderate relationship with the subject's relative COHS strength trended toward significance (r = 0.483; p = 0.068). Ballistic COHS produced superior potentiation effects compared with COHS performed in a nonballistic manner. Relative strength may contribute to the elicited potentiation response after ballistic and nonballistic COHS.

Application of Super-Hydrophobic Coating for Enhanced Water Repellency of Ballistic Fabric

Energy Technology Data Exchange (ETDEWEB)

Smith, Barton [ORNL; Rajic, Slobodan [ORNL; Hunter, Scott Robert [ORNL

2014-10-01

The objective of this work was to demonstrate that a superhydrophobic coating technology developed at Oak Ridge National Laboratory (ORNL) increases the water repellency of ballistic fabric beyond that provided by existing water repellency treatments. This increased water repellency has the potential to provide durable ballistic fabric for body armor without adding significant weight to the armor or significant manufacturing cost. Specimens of greige and scoured ballistic fabric were treated with a superhydrophobic coating and their weights and degree of water repellency were compared to specimens of untreated fabric. Treatment of both greige and scoured ballistic fabrics yielded highly water repellent fabrics. Our measurements of the water droplet contact angles gave values of approximately 150 , near the lower limit of 160 for superhydrophobic surfaces. The coatings increased the fabric weights by approximately 6%, an amount that is many times less than the estimated weight increase in a conventional treatment of ballistic fabric. The treated fabrics retained a significant amount of water repellency following a basic abrasion test, with water droplet contact angles decreasing by 14 to 23 . Microscopic analysis of the coating applied to woven fabrics indicated that the coating adhered equally well to fibers of greige and scoured yarns. Future evaluation of the superhydrophobic water repellent treatment will involve the manufacture of shoot packs of treated fabric for ballistic testing and provide an analysis of manufacturing scale-up and cost-to-benefit considerations.

Ballistic behaviour of ultra-high molecular weight polyethylene: effect of gamma radiation

International Nuclear Information System (INIS)

Alves, Andreia L.S.; Nascimento, Lucio F.C.; Miguez Suarez, Joao Carlos

2004-01-01

The fiber reinforced polymer matrix composites (PMCs) are considered excellent engineering materials. In structural applications, when a high strength-to-weight ratio is fundamental for the design, PMCs are successfully replacing many conventional materials. Since World War II textile materials have been used as ballistic armor. Materials manufactured with ultrahigh molecular weight polyethylene (UHMWPE) fibers are used in the production of armor materials, for personnel protection and armored vehicles. As these have been developed and commercialized more recently, there is not enough information about the action of the ionizing radiation in the ballistic performance of this armor material. In the present work the ballistic behavior of composite plates manufactured with ultrahigh molecular weight polyethylene (UHMWPE) fibers were evaluated after exposure to gamma radiation. The ballistic tests results were related to the macromolecular modifications induced by the environmental degradation through mechanical (hardness, impact and flexure) and physicochemical (infrared spectroscopy, differential scanning calorimetry and thermal gravimetric analysis) tests. Our results indicate that gamma irradiation induces modifications in the UHMWPE macromolecular chains, altering the mechanical properties of the composite and decreasing, for higher radiation doses, its ballistic performance. These results are presented and discussed. (author)

Supercurrent and multiple Andreev reflections in micrometer-long ballistic graphene Josephson junctions.

Science.gov (United States)

Zhu, Mengjian; Ben Shalom, Moshe; Mishchsenko, Artem; Fal'ko, Vladimir; Novoselov, Kostya; Geim, Andre

2018-02-08

Ballistic Josephson junctions are predicted to support a number of exotic physics processess, providing an ideal system to inject the supercurrent in the quantum Hall regime. Herein, we demonstrate electrical transport measurements on ballistic superconductor-graphene-superconductor junctions by contacting graphene to niobium with a junction length up to 1.5 μm. Hexagonal boron nitride encapsulation and one-dimensional edge contacts guarantee high-quality graphene Josephson junctions with a mean free path of several micrometers and record-low contact resistance. Transports in normal states including the observation of Fabry-Pérot oscillations and Sharvin resistance conclusively witness the ballistic propagation in the junctions. The critical current density J C is over one order of magnitude larger than that of the previously reported junctions. Away from the charge neutrality point, the I C R N product (I C is the critical current and R N the normal state resistance of junction) is nearly a constant, independent of carrier density n, which agrees well with the theory for ballistic Josephson junctions. Multiple Andreev reflections up to the third order are observed for the first time by measuring the differential resistance in the micrometer-long ballistic graphene Josephson junctions.

Drag of ballistic electrons by an ion beam

Energy Technology Data Exchange (ETDEWEB)

Gurevich, V. L.; Muradov, M. I., E-mail: mag.muradov@mail.ioffe.ru [Russian Academy of Sciences, Ioffe Physicotechnical Institute (Russian Federation)

2015-12-15

Drag of electrons of a one-dimensional ballistic nanowire by a nearby one-dimensional beam of ions is considered. We assume that the ion beam is represented by an ensemble of heavy ions of the same velocity V. The ratio of the drag current to the primary current carried by the ion beam is calculated. The drag current turns out to be a nonmonotonic function of velocity V. It has a sharp maximum for V near v{sub nF}/2, where n is the number of the uppermost electron miniband (channel) taking part in conduction and v{sub nF} is the corresponding Fermi velocity. This means that the phenomenon of ion beam drag can be used for investigation of the electron spectra of ballistic nanostructures. We note that whereas observation of the Coulomb drag between two parallel quantum wires may in general be complicated by phenomena such as tunneling and phonon drag, the Coulomb drag of electrons of a one-dimensional ballistic nanowire by an ion beam is free of such spurious effects.

Development of high-density ceramic composites for ballistic applications

International Nuclear Information System (INIS)

Rupert, N.L.; Burkins, M.S.; Gooch, W.A.; Walz, M.J.; Levoy, N.F.; Washchilla, E.P.

1993-01-01

The application of ceramic composites for ballistic application has been generally developed with ceramics of low density, between 2.5 and 4.5 g/cm 2 . These materials have offered good performance in defeating small-caliber penetrators, but can suffer time-dependent degradation effects when thicker ceramic tiles are needed to defeat modem, longer, heavy metal penetrators that erode rather than break up. This paper addresses the ongoing development, fabrication procedures, analysis, and ballistic evaluation of thinner, denser ceramics for use in armor applications. Nuclear Metals Incorporated (NMI) developed a process for the manufacture of depleted uranium (DU) ceramics. Samples of the ceramics have been supplied to the US Army Research Laboratory (ARL) as part of an unfunded cooperative study agreement. The fabrication processes used, characterization of the ceramic, and a ballistic comparison between the DU-based ceramic with baseline Al 2 O 3 will be presented

Relationship between traditional and ballistic squat exercise with vertical jumping and maximal sprinting.

Science.gov (United States)

Requena, Bernardo; García, Inmaculada; Requena, Francisco; de Villarreal, Eduardo Sáez-Sáez; Cronin, John B

2011-08-01

The purpose of this study was to quantify the magnitude of the relationship between vertical jumping and maximal sprinting at different distances with performance in the traditional and ballistic concentric squat exercise in well-trained sprinters. Twenty-one men performed 2 types of barbell squats (ballistic and traditional) across different loads with the aim of determining the maximal peak and average power outputs and 1 repetition maximum (1RM) values. Moreover, vertical jumping (countermovement jump test [CMJ]) and maximal sprints over 10, 20, 30, 40, 60, and 80 m were also assessed. In respect to 1RM in traditional squat, (a) no significant correlation was found with CMJ performance; (b) positive strong relationships (p ballistic and traditional squat exercises (r = 0.53-0.90); (c) negative significant correlations (r = -0.49 to -0.59, p ballistic or traditional squat exercises. Sprint time at 20 m was only related to ballistic and traditional squat performance when power values were expressed in relative terms. Moderate significant correlations (r = -0.39 to -0.56, p ballistic and traditional squat exercises. Sprint times at 60 and 80 m were mainly related to ballistic squat power outputs. Although correlations can only give insights into associations and not into cause and effect, from this investigation, it can be seen that traditional squat strength has little in common with CMJ performance and that relative 1RM and power outputs for both squat exercises are statistically correlated to most sprint distances underlying the importance of strength and power to sprinting.

Whither Ballistic Missile Defense?

Science.gov (United States)

1992-11-30

important that technology today is placing enormous power in the many camps-not only information that enables timely decision-making, but also the...WHITHER BALLISTIC MISSILE DEFENSE? BY AMBASSADOR HENRY F. COOPER NOVEMBER 30,1992 TECHNICAL MARKETING SOCIETY OF AMERICA WASHINGTON, DC...Conference on Technical Marketing 2000: Opportunities and Strategies for a Changing World) I intend to discuss the prospects for SDI in a changing

Ballistic model to estimate microsprinkler droplet distribution

Directory of Open Access Journals (Sweden)

Conceição Marco Antônio Fonseca

2003-01-01

Full Text Available Experimental determination of microsprinkler droplets is difficult and time-consuming. This determination, however, could be achieved using ballistic models. The present study aimed to compare simulated and measured values of microsprinkler droplet diameters. Experimental measurements were made using the flour method, and simulations using a ballistic model adopted by the SIRIAS computational software. Drop diameters quantified in the experiment varied between 0.30 mm and 1.30 mm, while the simulated between 0.28 mm and 1.06 mm. The greatest differences between simulated and measured values were registered at the highest radial distance from the emitter. The model presented a performance classified as excellent for simulating microsprinkler drop distribution.

Deep Interior: Multiple-Rendezvous Prospecting of NEOs

Science.gov (United States)

Kakuda, R. Y.; Asphaug, E.; Belton, M. J. S.; Gulkis, S.; Huebner, W. F.

2000-10-01

This is an international multiple-rendezvous mission designed to prospect the deep interior and subsurface geophysical properties of diverse near-Earth objects, using reflection radar tomography, imaging, gravity, and explosions. What we learn will greatly influence future missions and guide strategies for the diversion, disruption, or utilization of potentially hazardous objects. Deep Interior. Low-frequency radar to determine internal variations of complex permittivity at resolutions approaching 20 m. Map inclusions or voids, fracture geometries, and compositional or structural boundaries. Subsurface. High-frequency radar to determine depth of regolith, existence and nature of cometary mantle, geology beneath and around craters, and subsurface expressions to surface geology. Topography and Geodesy. Stereogrammetric imaging with 1 m/pixel spatial resolution, supplemented by radar altimetry in shadowed regions, to determine detailed shape, volume, and spin state. Compare with radar sounding to learn how internal structure is manifested on the surface. Mass and Density. Total mass and lower moments of the internal mass distribution by mapping the exterior gravitational field. Look for mass concentrations. Surface microphysics and composition. Map color, albedo, and scattering properties of the surface over sunlit regions in six optical filters. Material properties. Deploy grenades to characterize the mechanics and dynamics of surface materials. Record 8 frame/sec, 20 cm/pixel videos of crater formation and ejecta dynamics, to enable simple and direct laboratory constraints on material density, cohesion and porosity. Dust. Look for dust lofted by surface waves propagating from the explosions, to constrain elastic properties and attenuation. Observe longer-term dynamics and optical properties of dust "atmosphere" generated by human activity. Cometary Activity. At comet 107P/Wilson-Harrington, look for expressions of past cometary activity, and for possible awakening

Identification of lead sources in residential environments: Sydney Australia

International Nuclear Information System (INIS)

Laidlaw, M.A.S.; Zahran, S.; Pingitore, N.; Clague, J.; Devlin, G.; Taylor, M.P.

2014-01-01

Interior and exterior dust, soil and paint were analysed at five brick urban Sydney homes over 15 months to evaluate temporal variations and discriminate sources of lead (Pb) exposure. Exterior dust gauge Pb loading rates (μg/m 2 /28 days), interior vacuum dust Pb concentrations (mg/kg) and interior petri-dish Pb loading rates (μg/m 2 /28 days), were correlated positively with soil Pb concentrations. Exterior dust gauge Pb loading rates and interior vacuum dust Pb concentrations peaked in the summer. Lead isotope and Pb speciation (XAS) were analysed in soil and vacuum dust samples from three of the five houses that had elevated Pb concentrations. Results show that the source of interior dust lead was primarily from soil in two of the three houses and from soil and Pb paint in the third home. IEUBK child blood Pb modelling predicts that children's blood Pb levels could exceed 5 μg/dL in two of the five houses. -- Highlights: • Exterior Pb loading and interior Pb dust loading and concentrations correlate with soil Pb. • Exterior dust gauge Pb loading rates and interior vacuum dust Pb concentrations peak in the summer. • Interior dust lead came from soil in two of the three houses and from soil and Pb paint in the third home. • Modelling predicts that children's blood Pb levels could exceed 5 μg/dL in two of the five houses. -- Interior and exterior dust, soil and paint were analysed at five brick urban Sydney homes over 15 months to evaluate temporal variations and discriminate sources of lead (Pb) exposure

Learning without knowing: subliminal visual feedback facilitates ballistic motor learning

DEFF Research Database (Denmark)

Lundbye-Jensen, Jesper; Leukel, Christian; Nielsen, Jens Bo

by subconscious (subliminal) augmented visual feedback on motor performance. To test this, 45 subjects participated in the experiment, which involved learning of a ballistic task. The task was to execute simple ankle plantar flexion movements as quickly as possible within 200 ms and to continuously improve...... by the learner, indeed facilitated ballistic motor learning. This effect likely relates to multiple (conscious versus unconscious) processing of visual feedback and to the specific neural circuitries involved in optimization of ballistic motor performance.......). It is a well- described phenomenon that we may respond to features of our surroundings without being aware of them. It is also a well-known principle, that learning is reinforced by augmented feedback on motor performance. In the present experiment we hypothesized that motor learning may be facilitated...

Ballistic movements of jumping legs implemented as variable components of cricket behaviour.

Science.gov (United States)

Hustert, R; Baldus, M

2010-12-01

Ballistic accelerations of a limb or the whole body require special joint mechanisms in many animals. Specialized joints can be moved by stereotypic or variable motor control during motor patterns with and without ballistic components. As a model of variable motor control, the specialized femur-tibia (knee) joints of cricket (Acheta domesticus) hindlegs were studied during ballistic kicking, jumping and swimming and in non-ballistic walking. In this joint the tendons of the antagonistic flexor and the extensor muscles attach at different distances from the pivot and the opposed lever arms form an angle of 120 deg. A 10:1 ratio of their effective lever arms at full knee flexion helps to prepare for most ballistic extensions: the tension of the extensor can reach its peak while it is restrained by flexor co-contraction. In kicks, preparatory flexion is rapid and the co-contraction terminates just before knee extensions. Therefore, mainly the stored tension of the extensor muscle accelerates the small mass of the tibia. Jumps are prepared with slower extensor-flexor co-contractions that flex both knees simultaneously and then halt to rotate both legs outward to a near horizontal level. From there, catapult extension of both knees accelerates the body, supported by continued high frequency motor activity to their tibia extensor muscles during the ongoing push-off from the substrate. Premature extension of one knee instantly takes load from the lagging leg that extends and catches up, which finally results in a straight jump. In swimming, synchronous ballistic power strokes of both hindlegs drive the tibiae on a ventral-to-posterior trajectory through the water, well coordinated with the swimming patterns of all legs. In walking, running and climbing the steps of the hindlegs range between 45 deg flexion and 125 deg extension and use non-ballistic, alternating activity of knee flexor and extensor muscles. Steep climbing requires longer bursts from the extensor tibiae

Influence of structural properties on ballistic transport in nanoscale epitaxial graphene cross junctions

International Nuclear Information System (INIS)

Bock, Claudia; Weingart, Sonja; Karaissaridis, Epaminondas; Kunze, Ulrich; Speck, Florian; Seyller, Thomas

2012-01-01

In this paper we investigate the influence of material and device properties on the ballistic transport in epitaxial monolayer graphene and epitaxial quasi-free-standing monolayer graphene. Our studies comprise (a) magneto-transport in two-dimensional (2D) Hall bars, (b) temperature- and magnetic-field-dependent bend resistance of unaligned and step-edge-aligned orthogonal cross junctions, and (c) the influence of the lead width of the cross junctions on ballistic transport. We found that ballistic transport is highly sensitive to scattering at the step edges of the silicon carbide substrate. A suppression of the ballistic transport is observed if the lead width of the cross junction is reduced from 50 nm to 30 nm. In a 50 nm wide device prepared on quasi-free-standing graphene we observe a gradual transition from the ballistic into the diffusive transport regime if the temperature is increased from 4.2 to about 50 K, although 2D Hall bars show a temperature-independent mobility. Thus, in 1D devices additional temperature-dependent scattering mechanisms play a pivotal role. (paper)

Investigation of the potential barrier lowering for quasi-ballistic transport in short channel MOSFETs

International Nuclear Information System (INIS)

Lee, Jaehong; Kwon, Yongmin; Ji, Junghwan; Shin, Hyungcheol

2011-01-01

In this paper, the quasi-ballistic carrier transport in short channel MOSFETs is investigated from the point of potential barrier lowering. To investigate the ballistic characteristic of transistors, we extracted the channel backscattering coefficient and the ballistic ratio from experimental data obtained by RF C-V and DC I-V measurements. Two factors that modulate the potential barrier height, besides the gate bias, are considered in this work: the drain bias (V DS ) and the channel doping concentration (N A ). We extract the critical length by calculating the potential drop in the channel region and conclude that the drain bias and the channel doping concentration affect the quasi-ballistic carrier transport.

Development of Mortar Simulator with Shell-In-Shell System – Problem of External Ballistics

Directory of Open Access Journals (Sweden)

A. Fedaravicius

2007-01-01

Full Text Available The shell-in-shell system used in the mortar simulator raises a number of non-standard technical and computational problems starting from the requirement to distribute the propelling blast energy between the warhead and the ballistic barrel, finishing with the requirement that the length of warhead's flight path must be scaled to combat shell firing tables. The design problem of the simulator is split into two parts – the problem of external ballistics where the initial velocities of the warhead must be determined, and the problem of internal ballistics – where the design of the cartridge and the ballistic barrel must be performed.

Evaluating an Exterior Insulation and Finish System for Deep Energy Retrofits

Energy Technology Data Exchange (ETDEWEB)

Dentz, Jordan [National Renewable Energy Lab. (NREL), Golden, CO (United States); Podorson, David [National Renewable Energy Lab. (NREL), Golden, CO (United States)

2014-01-01

Exterior insulation and finish systems (EIFS) are proprietary synthetic formulations that are applied to the exterior walls of buildings to serve as insulation and exterior cladding. The insulation thickness can vary from less than one inch to a foot or more. In this project the applicability of EIFS for residential deep energy retrofits was investigated through modeling and a case study home. The home was retrofitted using a site-applied four-inch-thick EIFS. Site-specific details were developed as required for the residential retrofit application. Site work and the costs of the EIFS system were documented. The demonstration home was modeled using Building Energy Optimization energy and cost analysis software to explore cost effectiveness of various EIFS insulation thicknesses in two climate locations.

Overlapping Ballistic Ejecta Fields: Separating Distinct Blasts at Kings Bowl, Idaho

Science.gov (United States)

Borg, C.; Kobs-Nawotniak, S. E.; Hughes, S. S.; Sears, D. W. G.; Heldmann, J. L.; Lim, D. S. S.; Haberle, C. W.; Sears, H.; Elphic, R. C.; Kobayashi, L.; Garry, W. B.; Neish, C.; Karunatillake, S.; Button, N.; Purcell, S.; Mallonee, H.; Ostler, B.

2015-12-01

Kings Bowl is a ~2200ka pit crater created by a phreatic blast along a volcanic fissure in the eastern Snake River Plain (ESRP), Idaho. The main crater measures approximately 80m in length, 30m in width, and 30m in depth, with smaller pits located nearby on the Great Rift fissure, and has been targeted by the FINESSE team as a possible analogue for Cyane Fossae, Mars. The phreatic eruption is believed to have occurred due to the interaction of groundwater with lava draining back into the fissure following a lava lake high stand, erupting already solidified basalt from this and previous ERSP lava flows. The contemporaneous draw back of the lava with the explosions may conceal some smaller possible blast pits as more lava drained into the newly formed pits. Ballistic ejecta from the blasts occur on both sides of the fissure. To the east, the ballistic blocks are mantled by fine tephra mixed with eolian dust, the result of a westerly wind during the explosions. We use differential GPS to map the distribution of ballistic blocks on the west side of the fissure, recording position, percent vesiculation, and the length of 3 mutually perpendicular axes for each block >20cm along multiple transects parallel to the fissure. From the several hundred blocks recorded, we have been able to separate the ballistic field into several distinct blast deposits on the basis of size distributions and block concentration. The smaller pits identified from the ballistic fields correspond broadly to the northern and southern limits of the tephra/dust field east of the fissure. Soil formation and bioturbation of the tephra by sagebrush have obliterated any tephrostratigraphy that could have been linked to individual blasts. The ballistic block patterns at Kings Bowl may be used to identify distinct ejecta groups in high-resolution imagery of Mars or other planetary bodies.

BALLISTIC RESISTANT ARTICLES COMPRISING TAPES

NARCIS (Netherlands)

VAN DER EEM, JORIS; HARINGS, JULES; JANSE, GERARDUS; TJADEN, HENDRIK

2015-01-01

The invention pertains to a ballistic-resistant moulded article comprising a compressed stack of sheets comprising reinforcing tapes having a tensile strength of at least 1.0 GPa, a tensile modulus of at least 40 GPa, and a tensile energy-to-break of at least 15 J/g, the direction of the tapes

Ballistic Imaging and Scattering Measurements for Diesel Spray Combustion: Optical Development and Phenomenological Studies

Science.gov (United States)

2016-04-01

3mm) of diesel sprays from a high-pressure single-hole fuel injector . Ballistic imaging of dodecane and methyl oleate sprays are reported...Porter, Sean P. Duran, Terence E. Parker. Picosecond Ballistic Imaging of Ligament Structures in the Near- Nozzle Region of Diesel Sprays, ILASS...Experiments in Fluids (12 2014) Sean Duran, Jason Porter, Terence Parker. Ballistic Imaging of a Diesel Injector Spray at High Temperature and

77 FR 809 - Request for Proposals for Certification and Testing Expertise for the Ballistic Resistance of...

Science.gov (United States)

2012-01-06

... for Certification and Testing Expertise for the Ballistic Resistance of Personal Body Armor (2008... revising its Ballistic Resistance of Personal Body Armor (2008) Standard and corresponding certification... laboratories with experience in programs for similar types of ballistic-resistant personal protective equipment...

Hazard map for volcanic ballistic impacts at El Chichón volcano (Mexico)

Science.gov (United States)

Alatorre-Ibarguengoitia, Miguel; Ramos-Hernández, Silvia; Jiménez-Aguilar, Julio

2014-05-01

The 1982 eruption of El Chichón Volcano in southeastern Mexico had a strong social and environmental impact. The eruption resulted in the worst volcanic disaster in the recorded history of Mexico, causing about 2,000 casualties, displacing thousands, and producing severe economic losses. Even when some villages were relocated after the 1982 eruption, many people still live and work in the vicinities of the volcano and may be affected in the case of a new eruption. The hazard map of El Chichón volcano (Macías et al., 2008) comprises pyroclastic flows, pyroclastic surges, lahars and ash fall but not ballistic projectiles, which represent an important threat to people, infrastructure and vegetation in the case of an eruption. In fact, the fatalities reported in the first stage of the 1982 eruption were caused by roof collapse induced by ashfall and lithic ballistic projectiles. In this study, a general methodology to delimit the hazard zones for volcanic ballistic projectiles during volcanic eruptions is applied to El Chichón volcano. Different scenarios are defined based on the past activity of the volcano and parameterized by considering the maximum kinetic energy associated with ballistic projectiles ejected during previous eruptions. A ballistic model is used to reconstruct the "launching" kinetic energy of the projectiles observed in the field. The maximum ranges expected for the ballistics in the different explosive scenarios defined for El Chichón volcano are presented in a ballistic hazard map which complements the published hazard map. These maps assist the responsible authorities to plan the definition and mitigation of restricted areas during volcanic crises.

Numerical Method for Darcy Flow Derived Using Discrete Exterior Calculus

Science.gov (United States)

Hirani, A. N.; Nakshatrala, K. B.; Chaudhry, J. H.

2015-05-01

We derive a numerical method for Darcy flow, and also for Poisson's equation in mixed (first order) form, based on discrete exterior calculus (DEC). Exterior calculus is a generalization of vector calculus to smooth manifolds and DEC is one of its discretizations on simplicial complexes such as triangle and tetrahedral meshes. DEC is a coordinate invariant discretization, in that it does not depend on the embedding of the simplices or the whole mesh. We start by rewriting the governing equations of Darcy flow using the language of exterior calculus. This yields a formulation in terms of flux differential form and pressure. The numerical method is then derived by using the framework provided by DEC for discretizing differential forms and operators that act on forms. We also develop a discretization for a spatially dependent Hodge star that varies with the permeability of the medium. This also allows us to address discontinuous permeability. The matrix representation for our discrete non-homogeneous Hodge star is diagonal, with positive diagonal entries. The resulting linear system of equations for flux and pressure are saddle type, with a diagonal matrix as the top left block. The performance of the proposed numerical method is illustrated on many standard test problems. These include patch tests in two and three dimensions, comparison with analytically known solutions in two dimensions, layered medium with alternating permeability values, and a test with a change in permeability along the flow direction. We also show numerical evidence of convergence of the flux and the pressure. A convergence experiment is included for Darcy flow on a surface. A short introduction to the relevant parts of smooth and discrete exterior calculus is included in this article. We also include a discussion of the boundary condition in terms of exterior calculus.

Renovation and design of double casement windows with regard to the occurrence of water vapour condensation or mould on the interior surface of the window jamb

Science.gov (United States)

Kudrnacova, L.; Balik, L.

2017-10-01

The condensation of water vapour on the interior surface is an indicator of construction dysfunction or ignoring of the surroundings temperature and relative humidity. This paper deals with analysis of the occurrence of condensation on the jamb of double casement windows (windows with two window casements). More precisely, this is a surface in the interior where water vapour condensation or mould occur. For the renovation of existing double casement windows, there are different solutions based on window design: application of double insulating glazing on the interior window casement, application of double insulating glazing on the exterior casement, or installation of a simple window. We first describe measurement of an existing double casement window located in a mountain cottage. Second, the results and comparison of 2D thermal model of different types of double casement window construction. Also, the external insulation of the peripheral wall was included in the model.

Ballistic resistance of honeycomb sandwich panels under in-plane high-velocity impact.

Science.gov (United States)

Qi, Chang; Yang, Shu; Wang, Dong; Yang, Li-Jun

2013-01-01

The dynamic responses of honeycomb sandwich panels (HSPs) subjected to in-plane projectile impact were studied by means of explicit nonlinear finite element simulations using LS-DYNA. The HSPs consisted of two identical aluminum alloy face-sheets and an aluminum honeycomb core featuring three types of unit cell configurations (regular, rectangular-shaped, and reentrant hexagons). The ballistic resistances of HSPs with the three core configurations were first analyzed. It was found that the HSP with the reentrant auxetic honeycomb core has the best ballistic resistance, due to the negative Poisson's ratio effect of the core. Parametric studies were then carried out to clarify the influences of both macroscopic (face-sheet and core thicknesses, core relative density) and mesoscopic (unit cell angle and size) parameters on the ballistic responses of the auxetic HSPs. Numerical results show that the perforation resistant capabilities of the auxetic HSPs increase as the values of the macroscopic parameters increase. However, the mesoscopic parameters show nonmonotonic effects on the panels' ballistic capacities. The empirical equations for projectile residual velocities were formulated in terms of impact velocity and the structural parameters. It was also found that the blunter projectiles result in higher ballistic limits of the auxetic HSPs.

Coupling between a Langmuir wave and a ballistic perturbation

International Nuclear Information System (INIS)

Gervais, F.; Olivain, J.; Quemeneur, A.; Trocheris, M.

1980-01-01

The study of the mode-mode coupling usually neglects the ballistic contribution associated with parent waves. If this approximation is not made, a new mode, resulting from the interaction between the ballistic perturbation of pulsation ω 2 associated with one launched wave and the Landau component of pulsation ω 1 of the second one appears if ω 1 >ω 2 . The problem is solved theoretically and experimental evidence of this mode from measurements performed on a D.C. plasma column, confirms the results of this analysis

A Klein-tunneling transistor with ballistic graphene

Energy Technology Data Exchange (ETDEWEB)

Wilmart, Quentin; Fève, Gwendal; Berroir, Jean-Marc; Plaçais, Bernard [Laboratoire Pierre Aigrain, Ecole Normale Supérieure, CNRS (UMR 8551), Université P et M Curie, Université D Diderot, 24, rue Lhomond, 75231 Paris Cedex 05 (France); Berrada, Salim; Hung Nguyen, V; Dollfus, Philippe [Institute of Fundamental Electronics, Univ. Paris-Sud, CNRS, Orsay (France); Torrin, David [Département de Physique, Ecole Polytechnique, 91128 Palaiseau (France)

2014-06-15

Today, the availability of high mobility graphene up to room temperature makes ballistic transport in nanodevices achievable. In particular, p-n-p transistors in the ballistic regime give access to Klein tunneling physics and allow the realization of devices exploiting the optics-like behavior of Dirac Fermions (DFs) as in the Veselago lens or the Fabry–Pérot cavity. Here we propose a Klein tunneling transistor based on the geometrical optics of DFs. We consider the case of a prismatic active region delimited by a triangular gate, where total internal reflection may occur, which leads to the tunable suppression of transistor transmission. We calculate the transmission and the current by means of scattering theory and the finite bias properties using non-equilibrium Green's function (NEGF) simulation. (letter)

Navy Ohio Replacement (SSBN[X]) Ballistic Missile Submarine Program: Background and Issues for Congress

Science.gov (United States)

2016-04-05

Navy Ohio Replacement (SSBN[X]) Ballistic Missile Submarine Program: Background and Issues for Congress Ronald O’Rourke Specialist in Naval...Affairs April 5, 2016 Congressional Research Service 7-5700 www.crs.gov R41129 Navy Ohio Replacement (SSBN[X]) Ballistic Missile Submarine...1,091.1 million in research and development funding for the Ohio replacement program (ORP), a program to design and build a new class of 12 ballistic

Optimization theory for ballistic energy conversion

NARCIS (Netherlands)

Xie, Yanbo; Versluis, Michel; Van Den Berg, Albert; Eijkel, Jan C.T.

2016-01-01

The growing demand of renewable energy stimulates the exploration of new materials and methods for clean energy. We recently demonstrated a high efficiency and power density energy conversion mechanism by using jetted charged microdroplets, termed as ballistic energy conversion. Hereby, we model and

Electron Interference in Ballistic Graphene Nanoconstrictions

DEFF Research Database (Denmark)

Baringhaus, Jens; Settnes, Mikkel; Aprojanz, Johannes

2016-01-01

We realize nanometer size constrictions in ballistic graphene nanoribbons grown on sidewalls of SiC mesa structures. The high quality of our devices allows the observation of a number of electronic quantum interference phenomena. The transmissions of Fabry-Perot-like resonances are probed...

Transition from normal to ballistic diffusion in a one-dimensional impact system

Science.gov (United States)

Livorati, André L. P.; Kroetz, Tiago; Dettmann, Carl P.; Caldas, Iberê L.; Leonel, Edson D.

2018-03-01

We characterize a transition from normal to ballistic diffusion in a bouncing ball dynamics. The system is composed of a particle, or an ensemble of noninteracting particles, experiencing elastic collisions with a heavy and periodically moving wall under the influence of a constant gravitational field. The dynamics lead to a mixed phase space where chaotic orbits have a free path to move along the velocity axis, presenting a normal diffusion behavior. Depending on the control parameter, one can observe the presence of featured resonances, known as accelerator modes, that lead to a ballistic growth of velocity. Through statistical and numerical analysis of the velocity of the particle, we are able to characterize a transition between the two regimes, where transport properties were used to characterize the scenario of the ballistic regime. Also, in an analysis of the probability of an orbit to reach an accelerator mode as a function of the velocity, we observe a competition between the normal and ballistic transport in the midrange velocity.

The use of gelatine in wound ballistics research.

Science.gov (United States)

Carr, D J; Stevenson, T; Mahoney, P F

2018-04-25

Blocks of gelatine are used in both lethality and survivability studies for broadly the same reason, i.e. comparison of ammunition effects using a material that it is assumed represents (some part of) the human body. The gelatine is used to visualise the temporary and permanent wound profiles; elements of which are recognised as providing a reasonable approximation to wounding in humans. One set of researchers aim to improve the lethality of the projectile, and the other to understand the effects of the projectile on the body to improve survivability. Research areas that use gelatine blocks are diverse and include ammunition designers, the medical and forensics communities and designers of ballistic protective equipment (including body armour). This paper aims to provide an overarching review of the use of gelatine for wound ballistics studies; it is not intended to provide an extensive review of wound ballistics as that already exists, e.g. Legal Med 23:21-29, 2016. Key messages are that test variables, projectile type (bullet, fragmentation), impact site on the body and intermediate layers (e.g. clothing, personal protective equipment (PPE)) can affect the resulting wound profiles.

Realidad aumentada en exteriores e interiores

OpenAIRE

Gazcón, Nicolás Fernando; Trippel Nagel, Juan Manuel; Urribarri, Dana K.; Bjerg, Ernesto; Castro, Silvia Mabel

2015-01-01

La tecnología conocida como Realidad Aumentada ya forma parte con mayor frecuencia de nuestra vida cotidiana. Los avances tecnológicos como son, por ejemplo, los dispositivos móviles, han permitido que esta tecnología emergente esté al alcance de cualquier tipo de público. Si bien constantemente surgen diversas propuestas para entretenimiento, medicina, educación, turismo y mantenimiento, entre otras, todavía hay un largo camino por recorrer para que esta tecnología madure en cada campo, o...

Precession feature extraction of ballistic missile warhead with high velocity

Science.gov (United States)

Sun, Huixia

2018-04-01

This paper establishes the precession model of ballistic missile warhead, and derives the formulas of micro-Doppler frequency induced by the target with precession. In order to obtain micro-Doppler feature of ballistic missile warhead with precession, micro-Doppler bandwidth estimation algorithm, which avoids velocity compensation, is presented based on high-resolution time-frequency transform. The results of computer simulations confirm the effectiveness of the proposed method even with low signal-to-noise ratio.

Low-Energy Ballistic Transfers to Lunar Halo Orbits

Science.gov (United States)

Parker, Jeffrey S.

2009-01-01

Recent lunar missions have begun to take advantage of the benefits of low-energy ballistic transfers between the Earth and the Moon rather than implementing conventional Hohmann-like lunar transfers. Both Artemis and GRAIL plan to implement low-energy lunar transfers in the next few years. This paper explores the characteristics and potential applications of many different families of low-energy ballistic lunar transfers. The transfers presented here begin from a wide variety of different orbits at the Earth and follow several different distinct pathways to the Moon. This paper characterizes these pathways to identify desirable low-energy lunar transfers for future lunar missions.

3D topography measurements on correlation cells—a new approach to forensic ballistics identifications

International Nuclear Information System (INIS)

Song, John; Chu, Wei; Tong, Mingsi; Soons, Johannes

2014-01-01

Based on three-dimensional (3D) topography measurements on correlation cells, the National Institute of Standards and Technology (NIST) has developed the ‘NIST Ballistics Identification System (NBIS)’ aimed at accurate ballistics identifications and fast ballistics evidence searches. The 3D topographies are divided into arrays of correlation cells to identify ‘valid correlation areas’ and eliminate ‘invalid correlation areas’ from the matching and identification procedure. A ‘congruent matching cells’ (CMC)’ method using three types of identification parameters of the paired correlation cells (cross correlation function maximum CCF max , spatial registration position in x–y and registration angle θ) is used for high accuracy ballistics identifications. ‘Synchronous processing’ is proposed for correlating multiple cell pairs at the same time to increase the correlation speed. The proposed NBIS can be used for correlations of both geometrical topographies and optical intensity images. All the correlation parameters and algorithms are in the public domain and subject to open tests. An error rate reporting procedure has been developed that can greatly add to the scientific support for the firearm and toolmark identification specialty, and give confidence to the trier of fact in court proceedings. The NBIS is engineered to employ transparent identification parameters and criteria, statistical models and correlation algorithms. In this way, interoperability between different ballistics identification systems can be more easily achieved. This interoperability will make the NBIS suitable for ballistics identifications and evidence searches with large national databases, such as the National Integrated Ballistic Information Network in the United States. (paper)

Effect of joint design on ballistic performance of quenched and tempered steel welded joints

International Nuclear Information System (INIS)

Balakrishnan, M.; Balasubramanian, V.; Madhusudhan Reddy, G.

2014-01-01

Highlights: • Traditional usage of austenitic stainless steel filler for armour steel welding shows poor ballistic performance. • Earlier efforts show dubious success on ballistic resistance of armour steel joints. • Comparative evaluation of equal/unequal joint design on ballistic performance. • Effect of joint design covers the main aspects of successful bullet stoppage. - Abstract: A study was carried out to evaluate the effect of joint design on ballistic performance of armour grade quenched and tempered steel welded joints. Equal double Vee and unequal double Vee joint configuration were considered in this study. Targets were fabricated using 4 mm thick tungsten carbide hardfaced middle layer; above and below which austenitic stainless steel layers were deposited on both sides of the hardfaced interlayer in both joint configurations. Shielded metal arc welding process was used to deposit for all layers. The fabricated targets were evaluated for its ballistic performance and the results were compared in terms of depth of penetration on weld metal. From the ballistic test results, it was observed that both the targets successfully stopped the bullet penetration at weld center line. Of the two targets, the target made with unequal double Vee joint configuration offered maximum resistance to the bullet penetration at weld metal location without any bulge at the rear side. The higher volume of austenitic stainless steel front layer and the presence of hardfaced interlayer after some depth of soft austenitic stainless steel front layer is the primary reason for the superior ballistic performance of this joint

3D topography measurements on correlation cells—a new approach to forensic ballistics identifications

Science.gov (United States)

Song, John; Chu, Wei; Tong, Mingsi; Soons, Johannes

2014-06-01

Based on three-dimensional (3D) topography measurements on correlation cells, the National Institute of Standards and Technology (NIST) has developed the ‘NIST Ballistics Identification System (NBIS)’ aimed at accurate ballistics identifications and fast ballistics evidence searches. The 3D topographies are divided into arrays of correlation cells to identify ‘valid correlation areas’ and eliminate ‘invalid correlation areas’ from the matching and identification procedure. A ‘congruent matching cells’ (CMC)’ method using three types of identification parameters of the paired correlation cells (cross correlation function maximum CCFmax, spatial registration position in x-y and registration angle θ) is used for high accuracy ballistics identifications. ‘Synchronous processing’ is proposed for correlating multiple cell pairs at the same time to increase the correlation speed. The proposed NBIS can be used for correlations of both geometrical topographies and optical intensity images. All the correlation parameters and algorithms are in the public domain and subject to open tests. An error rate reporting procedure has been developed that can greatly add to the scientific support for the firearm and toolmark identification specialty, and give confidence to the trier of fact in court proceedings. The NBIS is engineered to employ transparent identification parameters and criteria, statistical models and correlation algorithms. In this way, interoperability between different ballistics identification systems can be more easily achieved. This interoperability will make the NBIS suitable for ballistics identifications and evidence searches with large national databases, such as the National Integrated Ballistic Information Network in the United States.

Schottky barrier height measurements of Cu/Si(001), Ag/Si(001), and Au/Si(001) interfaces utilizing ballistic electron emission microscopy and ballistic hole emission microscopy

International Nuclear Information System (INIS)

Balsano, Robert; Matsubayashi, Akitomo; LaBella, Vincent P.

2013-01-01

The Schottky barrier heights of both n and p doped Cu/Si(001), Ag/Si(001), and Au/Si(001) diodes were measured using ballistic electron emission microscopy and ballistic hole emission microscopy (BHEM), respectively. Measurements using both forward and reverse ballistic electron emission microscopy (BEEM) and (BHEM) injection conditions were performed. The Schottky barrier heights were found by fitting to a linearization of the power law form of the Bell-Kaiser BEEM model. The sum of the n-type and p-type barrier heights are in good agreement with the band gap of silicon and independent of the metal utilized. The Schottky barrier heights are found to be below the region of best fit for the power law form of the BK model, demonstrating its region of validity

Ballistic Missile Defense and ABM Treaty Limitations

National Research Council Canada - National Science Library

Robinson, Brian

1998-01-01

The U.S. must critically evaluate our current ballistic missile defense (BMD) strategy. In today's geostrategic context, is it sound strategy to continue to impose 1972 ABM Treaty restrictions on BMD systems development...

Ballistic Graphene Josephson Junctions from the Short to the Long Junction Regimes.

Science.gov (United States)

Borzenets, I V; Amet, F; Ke, C T; Draelos, A W; Wei, M T; Seredinski, A; Watanabe, K; Taniguchi, T; Bomze, Y; Yamamoto, M; Tarucha, S; Finkelstein, G

2016-12-02

We investigate the critical current I_{C} of ballistic Josephson junctions made of encapsulated graphene-boron-nitride heterostructures. We observe a crossover from the short to the long junction regimes as the length of the device increases. In long ballistic junctions, I_{C} is found to scale as ∝exp(-k_{B}T/δE). The extracted energies δE are independent of the carrier density and proportional to the level spacing of the ballistic cavity. As T→0 the critical current of a long (or short) junction saturates at a level determined by the product of δE (or Δ) and the number of the junction's transversal modes.

Herontwerp Ballistisch vest voor Vrouwen: Fase 1 (Redesign Ballistic Vest for Women: Phase 1)

National Research Council Canada - National Science Library

Koerhuis, C. L; Weghorst, M. G

2008-01-01

.... A questionnaire was filled out by fourteen female soldiers consisting of questions about complaints, characteristics of the ballistic vest and the mobility of the combat soldier wearing the ballistic vest...

Exteriorized colon anastomosis for unprepared bowel: An alternative to routine colostomy

Science.gov (United States)

Asfar, Sami K; Al-Sayer, Hilal M; Juma, Talib H

2007-01-01

AIM: To see the possibility of avoiding routine colostomy in patients presenting with unprepared bowel. METHODS: The cohort is composed of 103 patients, of these, 86 patients presented as emergencies (self-inflected and iatrogenic colon injuries, stab wounds and blast injury of the colon, volvulus sigmoid, obstructing left colon cancer, and strangulated ventral hernia). Another 17 patients were managed electively for other colon pathologies. During laparotomy, the involved segment was resected and the two ends of the colon were brought out via a separate colostomy wound. One layer of interrupted 3/0 silk was used for colon anastomosis. The exteriorized segment was immediately covered with a colostomy bag. Between the 5th and 7th postoperative day, the colon was easily dropped into the peritoneal cavity. The defect in the abdominal wall was closed with interrupted nonabsorbable suture. The skin was left open for secondary closure. RESULTS: The mean hospital stay (± SD) was 11.5 ± 2.6 d (8-20 d). The exteriorized colon was successfully dropped back into the peritoneal cavity in all patients except two. One developed a leak from oesophago-jejunostomy and from the exteriorized colon. She subsequently died of sepsis and multiple organ failure (MOF). In a second patient the colon proximal to the exteriorized anastomosis prolapsed and developed severe serositis, an elective ileo-colic anastomosis (to the left colon) was successfully performed. CONCLUSION: Exteriorized colon anastomosis is simple, avoids the inconvenience of colostomy and can be an alternative to routine colostomy. It is suitable where colostomy is socially unacceptable or the facilities and care is not available. PMID:17589900

A Klein-tunneling transistor with ballistic graphene

International Nuclear Information System (INIS)

Wilmart, Quentin; Fève, Gwendal; Berroir, Jean-Marc; Plaçais, Bernard; Berrada, Salim; Hung Nguyen, V; Dollfus, Philippe; Torrin, David

2014-01-01

Today, the availability of high mobility graphene up to room temperature makes ballistic transport in nanodevices achievable. In particular, p-n-p transistors in the ballistic regime give access to Klein tunneling physics and allow the realization of devices exploiting the optics-like behavior of Dirac Fermions (DFs) as in the Veselago lens or the Fabry–Pérot cavity. Here we propose a Klein tunneling transistor based on the geometrical optics of DFs. We consider the case of a prismatic active region delimited by a triangular gate, where total internal reflection may occur, which leads to the tunable suppression of transistor transmission. We calculate the transmission and the current by means of scattering theory and the finite bias properties using non-equilibrium Green's function (NEGF) simulation. (letter)

Wound ballistic evaluation of the Taser® XREP ammunition.

Science.gov (United States)

Kunz, Sebastian N; Adamec, Jiri; Zinka, Bettina; Münzel, Daniela; Noël, Peter B; Eichner, Simon; Manthei, Axel; Grove, Nico; Graw, M; Peschel, Oliver

2013-01-01

The Taser® eXtended Range Electronic Projectile (XREP®) is a wireless conducted electrical weapon (CEW) designed to incapacitate a person from a larger distance. The aim of this study was to analyze the ballistic injury potential of the XREP. Twenty rounds were fired from the Taser®X12 TM shotgun into ballistic soap covered with artificial skin and clothing at different shooting distances (1-25 m). One shot was fired at pig skin at a shooting distance of 10 m. The average projectile velocity was 67.0 m/s. The kinetic energy levels on impact varied from 28-52 J. Depending on the intermediate target, the projectiles penetrated up to 4.2 cm into the ballistic soap. On impact the nose assembly did not separate from the chassis, and no electrical activation was registered. Upon impact, a skin penetration of the XREP cannot be excluded. However, it is very unlikely at shooting distances of 10 m or more. Clothing and a high elasticity limit of the target body area can significantly reduce the penetration risk on impact.

On the influence of particle morphology on the post-impact ballistic response of ceramic armour materials

Science.gov (United States)

Hameed, Amer; Appleby-Thomas, Gareth; Wood, David; Jaansalu, Kevin

2015-06-01

Recent studies have shown evidence that the ballistic-resistance of fragmented (comminuted) ceramics is independent of the original strength of the material. In particular, experimental investigations into the ballistic behaviour of such fragmented ceramics have indicated that this response is correlated to shattered ceramic morphology. This suggests that careful control of ceramic microstructure - and therefore failure paths - might provide a route to optimise post-impact ballistic performance, thereby enhancing multi-hit capability. In this study, building on previous in-house work, ballistic tests were conducted using pre-formed `fragmented-ceramic' analogues based around three morphologically differing (but chemically identical) alumina feedstock materials compacted into target `pucks. In an evolution of previous work, variation of target thickness provided additional insight into an apparent morphology-based contribution to ballistic response.

The generalization of the exterior square of a Bieberbach group

Science.gov (United States)

Masri, Rohaidah; Hassim, Hazzirah Izzati Mat; Sarmin, Nor Haniza; Ali, Nor Muhainiah Mohd; Idrus, Nor'ashiqin Mohd

2014-06-01

The exterior square of a group is one of the homological functors which were originated in the homotopy theory. Meanwhile, a Bieberbach group is a torsion free crystallographic group. A Bieberbach group with cyclic point group of order two, C2, of dimension n can be defined as the direct product of that group of the smallest dimension with a free abelian group. Using the group presentation and commutator generating sequence, the exterior square of a Bieberbach group with point group C2 of dimension n is computed.

Elementos para una política exterior ambiental (Tema Central)

OpenAIRE

Salvador, Íñigo

2002-01-01

La necesidad de una política exterior ecuatoriana en lo ambiental surge de la naturaleza global del medio ambiente, de la responsabilidad del Ecuador como país privilegiado por su megadiversidad, de la vinculación inevitable entre la pobreza que le aqueja y la degradación del ambiente y de los compromisos internacionales por él adquiridos. Una política exterior ambiental debe resultar de un proceso de diseño en que participen todos los actores de la temática ambiental, aunque su ejecución deb...

Dynamic Load Measurement of Ballistic Gelatin Impact Using an Instrumented Tube

Science.gov (United States)

Seidt, J. D.; Periira, J. M.; Hammer, J. T.; Gilat, A.; Ruggeri, C. R.

2012-01-01

Bird strikes are a common problem for the aerospace industry and can cause serious damage to an aircraft. Ballistic gelatin is frequently used as a surrogate for actual bird carcasses in bird strike tests. Numerical simulations of these tests are used to supplement experimental data, therefore it is necessary to use numerical modeling techniques that can accurately capture the dynamic response of ballistic gelatin. An experimental technique is introduced to validate these modeling techniques. A ballistic gelatin projectile is fired into a strike plate attached to a 36 in. long sensor tube. Dynamic load is measured at two locations relative to the strike plate using strain gages configured in a full Wheatstone bridge. Data from these experiments are used to validate a gelatin constitutive model. Simulations of the apparatus are analyzed to investigate its performance.

Method of interior boundaries in a mixed problem of acoustic scattering

Directory of Open Access Journals (Sweden)

P. A. Krutitskii

1999-01-01

Full Text Available The mixed problem for the Helmholtz equation in the exterior of several bodies (obstacles is studied in 2 and 3 dimensions. The Dirichlet boundary condition is given on some obstacles and the impedance boundary condition is specified on the rest. The problem is investigated by a special modification of the boundary integral equation method. This modification can be called ‘Method of interior boundaries’, because additional boundaries are introduced inside scattering bodies, where impedance boundary condition is given. The solution of the problem is obtained in the form of potentials on the whole boundary. The density in the potentials satisfies the uniquely solvable Fredholm equation of the second kind and can be computed by standard codes. In fact our method holds for any positive wave numbers. The Neumann, Dirichlet, impedance problems and mixed Dirichlet–Neumann problem are particular cases of our problem.

Relevance of exterior appraisal in pig breeding

NARCIS (Netherlands)

Steenbergen, van E.J.

1990-01-01

In farm animals characterization of exterior is not a goal in itself but rather serves as an indicator of economically important traits, i.e. for pigs: growth performance, reproductivity and constitution. This indication might be of interest when these traits can not be measured