WorldWideScience

Sample records for extended range technique

  1. Extended range interferometry based on wavefront shaping

    Science.gov (United States)

    Szczupak, M. L.; Salbut, L.

    2007-09-01

    There are many cases when absolute measurements of objects with large height differences or height discontinuity is needed. These measurements can not be covered by classical interferometry since the range of non-ambiguity is limited to half the optical wavelength. Several techniques have been already developed for extending of non-ambiguity range. However most of them is based on multi-wavelength methods which demands expensive light sources and special environment conditions. In this work the new interferometric technique for absolute measurements of large steps discontinuities is proposed. Variable wavefront of the illuminating beam and special procedure for calibration of the measurement volume are used for extending of the measurement range without using multispectral sources. Additionally, calibration of the measurement area simplifies fringe processing and quicken measures. Theoretical analysis of this technique, its numerical simulations and experimental verification are presented and discussed.

  2. Automated dual-exposure technique to extend the dynamic range of flat-panel detectors used in small-animal cone-beam micro-CT

    OpenAIRE

    Sisniega, Alejandro; Vaquero, Juan José; Abella García, Mónica; Vidal-Migallón, I.; Lage, Eduardo; Desco, Manuel

    2009-01-01

    Proceeding: 2009 IEEE Nuclear Science Symposium Conference Record (NSS/MIC), Orlando, Florida, 25-31 October 2009 This work presents an approach to extend the dynamic range of X ray flat panel detectors for cone beam micro CT by using two different acquisitions of the same sample, taken at two different X ray photon fluxes with the same X ray beam peak energy and filtration. Photon flux for the first scan is chosen as the maximum possible value not saturating the detector in the low att...

  3. Real-time extended dynamic range imaging in shearography.

    Science.gov (United States)

    Groves, Roger M; Pedrini, Giancarlo; Osten, Wolfgang

    2008-10-20

    Extended dynamic range (EDR) imaging is a postprocessing technique commonly associated with photography. Multiple images of a scene are recorded by the camera using different shutter settings and are merged into a single higher dynamic range image. Speckle interferometry and holography techniques require a well-modulated intensity signal to extract the phase information, and of these techniques shearography is most sensitive to different object surface reflectivities as it uses self-referencing from a sheared image. In this paper the authors demonstrate real-time EDR imaging in shearography and present experimental results from a difficult surface reflectivity sample: a wooden panel painting containing gold and dark earth color paint.

  4. Enhanced Graphics for Extended Scale Range

    Science.gov (United States)

    Hanson, Andrew J.; Chi-Wing Fu, Philip

    2012-01-01

    Enhanced Graphics for Extended Scale Range is a computer program for rendering fly-through views of scene models that include visible objects differing in size by large orders of magnitude. An example would be a scene showing a person in a park at night with the moon, stars, and galaxies in the background sky. Prior graphical computer programs exhibit arithmetic and other anomalies when rendering scenes containing objects that differ enormously in scale and distance from the viewer. The present program dynamically repartitions distance scales of objects in a scene during rendering to eliminate almost all such anomalies in a way compatible with implementation in other software and in hardware accelerators. By assigning depth ranges correspond ing to rendering precision requirements, either automatically or under program control, this program spaces out object scales to match the precision requirements of the rendering arithmetic. This action includes an intelligent partition of the depth buffer ranges to avoid known anomalies from this source. The program is written in C++, using OpenGL, GLUT, and GLUI standard libraries, and nVidia GEForce Vertex Shader extensions. The program has been shown to work on several computers running UNIX and Windows operating systems.

  5. Extending the Dynamic Range of a Time Projection Chamber

    Science.gov (United States)

    Estee, Justin; S πRIT Collaboration

    2017-09-01

    The use of Time Projection Chambers (TPCs) in intermediate heavy ion reactions faces some challenges in addressing the energy losses that range from the small energy loss of relativistic pions to the large energy loss of slow moving heavy ions. A typical trade-off can be to set the smallest desired signals to be well within the lower limits of the dynamic range of the electronics while allowing for some larger signals to saturate the electronics. With wire plane anodes, signals from readout pads further away from the track remain unsaturated and allow signals from tracks with saturated pads to be accurately recovered. We illustrate this technique using data from the SAMURAI Pion-Reconstruction and Ion-Tracker (S πRIT) TPC , which recently measured pions and light charged particles in collisions of Sn+Sn isotopes. Our method exploits knowledge of how the induced charge distribution depends on the distance from the track to smoothly extend dynamic range even when some of the pads in the track are saturated. To accommodate the analysis of slow moving heavy ions, we have extended the Bichsel energy loss distributions to handle slower moving ions as well. In this talk, I will discuss a combined approach which successfully extends the dynamic range of the TPC electronics. This work is supported by the U.S. DOE under Grant Nos. DE-SC0014530, DE-NA0002923, US NSF Grant No. PHY-1565546 and the Japan MEXT KAKENHI Grant No. 24105004.

  6. Extended-range order in glasses

    Energy Technology Data Exchange (ETDEWEB)

    Ellison, A.J.G.; Price, D.L.; Saboungi, M.L. [Argonne National Lab., IL (United States); Egami, T.; Hu, Rui-Zhong [Pennsylvania Univ., Philadelphia, PA (United States); Howells, W.S. [Rutherford Appleton Lab., Chilton (United Kingdom)

    1994-03-01

    A new type of order is identified in complex glasses, characterized by diffraction peaks at values of the wave vector below those typical of intermediate-range order. Combined neutron and anomalous x-ray diffraction studies of one glass exhibiting this behavior, vitreous rubidium germanate, indicate it to be associated with chemical ordering of the two cations with respect to each other.

  7. Extended Resin Composite Restorations: Techniques and Procedures

    NARCIS (Netherlands)

    Loomans, B.A.C.; Hilton, T.

    2016-01-01

    This article gives an overview of the state of the art of different restorative treatment procedures and techniques needed for placing extended posterior resin composite restorations. Clinical aspects related to the procedure are discussed and reviewed based on the current literature, such as the

  8. Start-Stop Moment Optimization of Range Extender and Control Strategy Design for Extended -Range Electric Vehicle

    Science.gov (United States)

    Zhao, Jing-bo; Han, Bing-yuan; Bei, Shao-yi

    2017-10-01

    Range extender is the core component of E-REV, its start-stop control determines the operation modes of vehicle. This paper based on a certain type of E-REV, researched constant power control strategy of range extender in extended-range model, to target range as constraint condition, combined with different driving cycle conditions, by correcting battery SOC for range extender start-stop moment, optimized the control strategy of range extender, and established the vehicle and range extender start-stop control simulation model. Selected NEDC and UDDS conditions simulation results show that: under certain target mileage, the range extender running time reduced by 37.2% and 28.2% in the NEDC condition, and running time UDDS conditions were reduced by 40.6% and 33.5% in the UDDS condition, reached the purpose of meeting the vehicle mileage and reducing consumption and emission.

  9. Extended overview techniques for outdoor augmented reality.

    Science.gov (United States)

    Veas, Eduardo; Grasset, Raphaël; Kruijff, Ernst; Schmalstieg, Dieter

    2012-04-01

    In this paper, we explore techniques that aim to improve site understanding for outdoor Augmented Reality (AR) applications. While the first person perspective in AR is a direct way of filtering and zooming on a portion of the data set, it severely narrows overview of the situation, particularly over large areas. We present two interactive techniques to overcome this problem: multi-view AR and variable perspective view. We describe in details the conceptual, visualization and interaction aspects of these techniques and their evaluation through a comparative user study. The results we have obtained strengthen the validity of our approach and the applicability of our methods to a large range of application domains.

  10. In-Situ Extended Lateral Range Surface Metrology Project

    Data.gov (United States)

    National Aeronautics and Space Administration — We propose to develop an extended lateral range capability for a dynamic optical profiling system to enable non-contact, surface roughness measurement of large and...

  11. Primary Paralleled Isolated Boost Converter with Extended Operating Voltage Range

    DEFF Research Database (Denmark)

    Hernandez Botella, Juan Carlos; Sen, Gökhan; Mira Albert, Maria del Carmen

    2012-01-01

    Applications requiring wide input and output voltage range cannot often be satisfied by using buck or boost derived topologies. Primary paralleled isolated boost converter (PPIBC) [1]-[2] is a high efficiency boost derived topology. This paper proposes a new operation mode for extending the input...

  12. The electrification of the powertrain - from turbohybrid to range extender; Die Elektrifizierung des Antriebs - vom Turbohybrid zum Range Extender

    Energy Technology Data Exchange (ETDEWEB)

    Fischer, Robert [AVL List GmbH, Graz (Austria)

    2009-07-01

    One of the most concise trends of the last years is the accelerated electrification of the drive strand. For an optimum cost benefit ratio new engine concepts are developed whereby with each concept the key lies in the system tuning. Engine, transmissions, electric motor, battery and tax strategies are optimally co-ordinated. This is exemplary presented at two concepts of emphasis: (a) Turbo-hydride: Utilization of burn-motor auxiliary functions for the simplification of the electrical system; (b) Rank Extender: Here, there exist two different solutions: Solutions with direct drift punch and the pure Range Extender without direct drift punch.

  13. Long-Range Persistence Techniques Evaluated

    Science.gov (United States)

    Witt, A.; Malamud, B. D.

    2006-12-01

    Many time series in the Earth Sciences exhibit persistence (memory) where large values (small values) `cluster' together. Here we examine long-range persistence, where one value is correlated with all others in the time series. A time series is long-range persistent (a self-affine fractal) if the power spectral density scales with a power law. The scaling exponent beta characterizes the `strength' of persistence. We compare five common analysis techniques for quantifying long-range persistence: (a) Power-spectral analysis, (b) Wavelet variance analysis, (c) Detrended Fluctuation analysis, (d) Semivariogram analysis, and (e) Rescaled-Range (R/S) analysis. To evaluate these methods, we construct 26,000 synthetic fractional noises with lengths between 512 and 4096, different persistence strengths, different distributions (normal, log-normal, levy), and using different construction methods: Fourier filtering, discrete wavelets, random additions, and Mandelbrot `cartoon' Brownian motions. We find: (a) Power-spectral and wavelet analyses are the most robust for measuring long-range persistence across all beta, although `antipersistence' is over-estimated for non- Gaussian time series. (b) Detrended Fluctuation Analysis is appropriate for signals with long-range persistence strength beta between -0.2 and 2.8 and has very large 95% confidence intervals for non-Gaussian signals. (c) Semivariograms are appropriate for signals with long-range persistence strength between 1.0 and 2.8; it has large confidence intervals and systematically underestimates log-normal noises in this range. (d) Rescaled- Range Analysis is only accurate for beta of about 0.7. We conclude some techniques are much better suited than others for quantifying long-range persistence, and the resultant beta (and associated error bars on them) are sensitive to the one point probability distribution, the length of the time series, and the techniques used.

  14. Extended piano techniques : in theory, history and performance practice

    NARCIS (Netherlands)

    Vaes, Luc Paul Frank

    2009-01-01

    So-called "extended techniques" have suffered a consistent lack of understanding from a theoretical, historical and practical point of view. Although most of them – e.g. playing directly on the strings, cluster- and glissando-techniques – exist in a substantial part of the repertoire for the piano

  15. Use of Extended Flute Techniques in Flute Education in Turkey

    Science.gov (United States)

    Sakin, Ajda Senol

    2018-01-01

    Extended flute techniques, which are frequently found in contemporary flute literature, carry the flute to a different dimension, pushing the boundaries of composers and performers. Although the number of pieces containing these techniques in the world has increased rapidly, along with Turkish flute repertoire, written Turkish sources about…

  16. Monte Carlo modelling of an extended DXA technique

    Science.gov (United States)

    Michael, G. J.; Henderson, C. J.

    1998-09-01

    The precision achieved in measuring bone mineral density (BMD) by commercial dual-energy x-ray absorptiometry (DXA) machines is typically better than 1%, but accuracy is considerably worse. Errors, due to inhomogeneous distributions of fat, of up to 10% have been reported. These errors arise because the DXA technique assumes a two-component model for the human body, i.e. bone mineral and soft tissue. This paper describes an extended DXA technique that uses a three-component model of human tissue and significantly reduces errors due to inhomogeneous fat distribution. In addition to two x-ray transmission measurements, a measurement of the path length of the x-ray beam within the patient is required. This provides a third equation, i.e. where T, , and are the total, lean soft tissue, bone mineral and fatty tissue thicknesses respectively. Monte Carlo modelling was undertaken to make a comparison of the standard and extended DXA techniques in the presence of inhomogeneous fat distribution. Two geometries of varying complexity were simulated. In each case the extended DXA technique produced BMD measurements that were independent of soft tissue composition whereas the standard technique produced BMD measurements that were strongly dependent on soft tissue composition. For example, in one case, the gradients of the plots of BMD versus fractional fat content were for standard DXA and for extended DXA . In all cases the extended DXA method produced more accurate but less precise results than the standard DXA technique.

  17. Extended-Range Passive RFID and Sensor Tags

    Science.gov (United States)

    Fink, Patrick W.; Kennedy, Timothy F.; Lin, Gregory Y.; Barton, Richard

    2012-01-01

    Extended-range passive radio-frequency identification (RFID) tags and related sensor tags are undergoing development. A tag of this type incorporates a retroreflective antenna array, so that it reflects significantly more signal power back toward an interrogating radio transceiver than does a comparable passive RFID tag of prior design, which does not incorporate a retroreflective antenna array. Therefore, for a given amount of power radiated by the transmitter in the interrogating transceiver, a tag of this type can be interrogated at a distance greater than that of the comparable passive RFID or sensor tag of prior design. The retroreflective antenna array is, more specifically, a Van Atta array, named after its inventor and first published in a patent issued in 1959. In its simplest form, a Van Atta array comprises two antenna elements connected by a transmission line so that the signal received by each antenna element is reradiated by the other antenna element (see Figure 1). The phase relationships among the received and reradiated signals are such as to produce constructive interference of the reradiated signals; that is, to concentrate the reradiated signal power in a direction back toward the source. Hence, an RFID tag equipped with a Van Atta antenna array automatically tracks the interrogating transceiver. The effective gain of a Van Atta array is the same as that of a traditional phased antenna array having the same number of antenna elements. Additional pairs of antenna elements connected by equal-length transmission lines can be incorporated into a Van Atta array to increase its directionality. Like some RFID tags here-to-fore commercially available, an RFID or sensor tag of the present developmental type includes one-port surface-acoustic-wave (SAW) devices. In simplified terms, the mode of operation of a basic one-port SAW device as used heretofore in an RFID device is the following: An interrogating radio signal is converted, at an input end, from

  18. An Extended-range Hydrometeorological Ensemble Prediction System for Alpine Catchments in Switzerland

    Science.gov (United States)

    Monhart, Samuel; Bogner, Konrad; Spirig, Christoph; Bhend, Jonas; Liniger, Mark A.; Zappa, Massimiliano; Schär, Christoph

    2017-04-01

    In recent years meteorological ensemble prediction systems have increasingly be used to feed hydrological models in order to provide probabilistic streamflow forecasts. Such hydrological ensemble prediction systems (HEPS) have been analyzed for different lead times from short-term to seasonal predictions and are used for different applications. Especially at longer lead times both such forecasts exhibit systematic biases which can be removed by applying bias correction techniques to both the meteorological and/or the hydrological output. However, it is still an open question if pre- or post-processing techniques or both should be applied. We will present first results of the analysis of pre- and post-processed extended-range hydrometeorological forecasts. In a first step the performance of bias corrected and downscaled (using quantile mapping) extended-range meteorological forecasts provided by the ECMWF is assessed for approximately 1000 ground observation sites across Europe. Generally, bias corrected meteorological forecasts show positive skill in terms of CRPSS up to three (two) weeks for weekly mean temperature (precipitation) compared to climatological forecasts. For the Alpine region the absolute skill is generally lower but the relative gain in skill resulting from the bias correction is larger. These pre-processed meteorological forecasts of one year of ECMWF extended-range forecasts and corresponding hindcasts are used to feed a hydrological model for a selected catchment in the Alpine area in Switzerland. Furthermore, different post-processing techniques are tested to correct the resulting streamflow forecasts. This will allow to determine the relative effect of pre- and post-processing of extended-range hydrometeorological predictions in Alpine catchments. Future work will include the combination of these corrected streamflow forecasts with electricity price forecasts to optimize the operations and revenues of hydropower systems in the Alps.

  19. Extending the range of low energy electron diffraction (LEED) surface structure determination: Co-adsorbed molecules, incommensurate overlayers and alloy surface order studied by new video and electron counting LEED techniques

    Energy Technology Data Exchange (ETDEWEB)

    Ogletree, D.F.

    1986-11-01

    LEED multiple scattering theory is briefly summarized, and aspects of electron scattering with particular significance to experimental measurements such as electron beam coherence, instrument response and phonon scattering are analyzed. Diffuse LEED experiments are discussed. New techniques that enhance the power of LEED are described, including a real-time video image digitizer applied to LEED intensity measurements, along with computer programs to generate I-V curves. The first electron counting LEED detector using a ''wedge and strip'' position sensitive anode and digital electronics is described. This instrument uses picoampere incident beam currents, and its sensitivity is limited only by statistics and counting times. Structural results on new classes of surface systems are presented. The structure of the c(4 x 2) phase of carbon monoxide adsorbed on Pt(111) has been determined, showing that carbon monoxide molecules adsorb in both top and bridge sites, 1.85 +- 0.10 A and 1.55 +- 0.10 A above the metal surface, respectively. The structure of an incommensurate graphite overlayer on Pt(111) is analyzed. The graphite layer is 3.70 +- 0.05 A above the metal surface, with intercalated carbon atoms located 1.25 +- 0.10 A above hollow sites supporting it. The (2..sqrt..3 x 4)-rectangular phase of benzene and carbon monoxide coadsorbed on Pt(111) is analyzed. Benzene molecules adsorb in bridge sites parallel to and 2.10 +- 0.10 A above the surface. The carbon ring is expanded, with an average C-C bond length of 1.72 +- 0.15 A. The carbon monoxide molecules also adsorb in bridge sites. The structure of the (..sqrt..3 x ..sqrt..3) reconstruction on the (111) face of the ..cap alpha..-CuAl alloy has been determined.

  20. Ground-Based Midcourse Defense (GMD) Extended Test Range (ETR)

    Science.gov (United States)

    2003-07-01

    Steller’s eiders and endangered short-tailed albatross offshore would also be outside the range of site preparation noise levels and are not...bird populations. Waterfowl would quickly resume feeding and other normal behavior patterns after a launch is completed. GMD ETR Final EIS es...mammal. No significant long-term adverse impacts are anticipated to seabirds and shorebirds, Guadalupe fur seals, California sea lions, northern

  1. A dual-detector extended range rem-counter

    CERN Document Server

    Ferrarini, M; Silari, M; Agosteo, S

    2010-01-01

    The design and characterization of a dual-detector spherical rem counter is discussed in this paper. The rem counter is based on a polythene sphere with lead and cadmium insets, designed to host at its centre either an active (He-3 SP9 proportional counter) or a passive (CR39 + B-10 radiator) thermal neutron detector. Its sensitivity ranges from thermal energies up to 1 GeV. A Monte Carlo characterization of this dual-detector rem counter has shown no significant change in the shape of the response curve obtained with the two detectors. The rem counter has been calibrated with a Pu-Be source. An intercomparison in a high-energy neutron field has been carried out at the CERF facility at CERN among the rem counter in the two configurations, two commercial units and the original version of the active LINUS in use at CERN. Both the active and passive versions of the rem counter agree, within the statistical uncertainties, with the CERN LINUS and with the facility reference values. Both versions of the instrument ...

  2. [The Extended Percutaneous Needle Fasciotomy Technique (PNF+) For Dupuytren's Contracture].

    Science.gov (United States)

    Lenze, Wolfgang Paul

    2017-02-01

    The extended percutaneous needle fasciotomy (PNF+) is a minimal invasive technique especially suitable for treating severe Dupuytren's contractures and recurrences. The familiar needle fasciotomy is complemented by a spontaneous tearing of the skin and a full-thickness graft to cover the defect. Skin tears in fingers and palm are not a complication, but an integral part of the PNF+. The neurovascular bundles remain intact. This surgical procedure may be repeated as often as required. © Georg Thieme Verlag KG Stuttgart · New York.

  3. Bias correction and verification of extended-range ECMWF forecasts against ground observations in Europe

    Science.gov (United States)

    Monhart, Samuel; Spirig, Christoph; Bhend, Jonas; Liniger, Mark A.; Bogner, Konrad; Schär, Christoph

    2017-04-01

    In recent years large progress has been made in numerical weather prediction. The implementation of ensemble forecasts has led to better predictability especially at longer lead times, including extended-range (monthly) to seasonal time horizons. The verification of such predictions is often done for areal averages of upper air parameters. Only few studies exist that verify the forecasts for surface parameters at point locations although applications often require local information. With this study we aim at providing an extensive station-wise verification of extended range forecasts in Europe. We therefore verified the ECMWF extended-range forecast against approximately 1000 ground based observational time series across Europe. To do so, we made use of 20 years of hindcasts of the forecasting system that was operational from May 2014 to April 2015 (cycle 40r1), yielding an analysis period of May 1995 to June 2014. This data set is large enough to stratify the performance of the forecast system with season and region. Weekly temperature and precipitation of both raw hindcasts and post-processed hindcasts were analyzed. For the post-processing two techniques were compared, a mean debiasing (MD) and a quantile mapping (QM) approach. Various skill scores (RPSS, CRPSS, ROCSS) characterizing different aspects of forecast quality were computed using simple forecasts based on climatology as a benchmark. Overall, skillful forecasts were found in some regions and seasons up to three weeks of lead time in case of temperature and up to two weeks for precipitation, respectively. Bias-corrections allowed to enhance forecast skill in the first two weeks for most of the stations. QM generally performed better in particular concerning the improvement of reliability as illustrated by the resulting spread to error ratios close to one. Spatial and seasonal differences in skill were found both for temperature and precipitation, with winter forecasts generally being better than those

  4. Extending Driving Vision Based on Image Mosaic Technique

    Directory of Open Access Journals (Sweden)

    Chen Deng

    2017-01-01

    Full Text Available Car cameras have been used extensively to assist driving by make driving visible. However, due to the limitation of the Angle of View (AoV, the dead zone still exists, which is a primary origin of car accidents. In this paper, we introduce a system to extend the vision of drivers to 360 degrees. Our system consists of four wide-angle cameras, which are mounted at different sides of a car. Although the AoV of each camera is within 180 degrees, relying on the image mosaic technique, our system can seamlessly integrate 4-channel videos into a panorama video. The panorama video enable drivers to observe everywhere around a car as far as three meters from a top view. We performed experiments in a laboratory environment. Preliminary results show that our system can eliminate vision dead zone completely. Additionally, the real-time performance of our system can satisfy requirements for practical use.

  5. Comparative analysis of numerical simulation techniques for incoherent imaging of extended objects through atmospheric turbulence

    Science.gov (United States)

    Lachinova, Svetlana L.; Vorontsov, Mikhail A.; Filimonov, Grigory A.; LeMaster, Daniel A.; Trippel, Matthew E.

    2017-07-01

    Computational efficiency and accuracy of wave-optics-based Monte-Carlo and brightness function numerical simulation techniques for incoherent imaging of extended objects through atmospheric turbulence are evaluated. Simulation results are compared with theoretical estimates based on known analytical solutions for the modulation transfer function of an imaging system and the long-exposure image of a Gaussian-shaped incoherent light source. It is shown that the accuracy of both techniques is comparable over the wide range of path lengths and atmospheric turbulence conditions, whereas the brightness function technique is advantageous in terms of the computational speed.

  6. NREL/Industry Range-Extended Electric Vehicle for Package Delivery

    Energy Technology Data Exchange (ETDEWEB)

    Farrell, John T [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Kelly, Kenneth J [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Duran, Adam W [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Lammert, Michael P [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Miller, Eric S [National Renewable Energy Laboratory (NREL), Golden, CO (United States)

    2018-01-15

    Range-extended electric vehicle (EV) technology can be a viable option for reducing fuel consumption from medium-duty (MD) and heavy-duty (HD) engines by approximately 50 percent or more. Such engines have wide variations in use and duty cycles, however, and identifying the vocations/duty cycles most suitable for range-extended applications is vital for maximizing the potential benefits. This presentation provides information about NREL's research on range-extended EV technologies, with a focus on NREL's real-world data collection and analysis approach to identifying the vocations/duty cycles best suited for range-extender applications and to help guide related powertrain optimization and design requirements. The presentation also details NREL's drive cycle development process as it pertains to package delivery applications.

  7. Design considerations of a linear generator for a range extender application

    Directory of Open Access Journals (Sweden)

    Seo Un-Jae

    2015-12-01

    Full Text Available The free piston linear generator is a new range extender concept for the application in a full electric vehicle. The free piston engine driven linear generators can achieve high efficiency at part and full load which is suitable for the range extender application. This paper presents requirements for designing a linear generator deduced from a basic analysis of a free piston linear generator.

  8. HEPS4Power - Extended-range Hydrometeorological Ensemble Predictions for Improved Hydropower Operations and Revenues

    Science.gov (United States)

    Bogner, Konrad; Monhart, Samuel; Liniger, Mark; Spririg, Christoph; Jordan, Fred; Zappa, Massimiliano

    2015-04-01

    In recent years large progresses have been achieved in the operational prediction of floods and hydrological drought with up to ten days lead time. Both the public and the private sectors are currently using probabilistic runoff forecast in order to monitoring water resources and take actions when critical conditions are to be expected. The use of extended-range predictions with lead times exceeding 10 days is not yet established. The hydropower sector in particular might have large benefits from using hydro meteorological forecasts for the next 15 to 60 days in order to optimize the operations and the revenues from their watersheds, dams, captions, turbines and pumps. The new Swiss Competence Centers in Energy Research (SCCER) targets at boosting research related to energy issues in Switzerland. The objective of HEPS4POWER is to demonstrate that operational extended-range hydro meteorological forecasts have the potential to become very valuable tools for fine tuning the production of energy from hydropower systems. The project team covers a specific system-oriented value chain starting from the collection and forecast of meteorological data (MeteoSwiss), leading to the operational application of state-of-the-art hydrological models (WSL) and terminating with the experience in data presentation and power production forecasts for end-users (e-dric.ch). The first task of the HEPS4POWER will be the downscaling and post-processing of ensemble extended-range meteorological forecasts (EPS). The goal is to provide well-tailored forecasts of probabilistic nature that should be reliable in statistical and localized at catchment or even station level. The hydrology related task will consist in feeding the post-processed meteorological forecasts into a HEPS using a multi-model approach by implementing models with different complexity. Also in the case of the hydrological ensemble predictions, post-processing techniques need to be tested in order to improve the quality of the

  9. A comparison of some range condition assessment techniques used ...

    African Journals Online (AJOL)

    Techniques currently used to assess range condition in the grassland biome of Southern Africa are reviewed. These indices were then used to evaluate each method in terms of sensitivity, index interpretation and efficiency, bearing in mind the objectives of each technique. The weighted key species method and ...

  10. Performance and driveline analyses of engine capacity in range extender engine hybrid vehicle

    Science.gov (United States)

    Praptijanto, Achmad; Santoso, Widodo Budi; Nur, Arifin; Wahono, Bambang; Putrasari, Yanuandri

    2017-01-01

    In this study, range extender engine designed should be able to meet the power needs of a power generator of hybrid electrical vehicle that has a minimum of 18 kW. Using this baseline model, the following range extenders will be compared between conventional SI piston engine (Baseline, BsL), engine capacity 1998 cm3, and efficiency-oriented SI piston with engine capacity 999 cm3 and 499 cm3 with 86 mm bore and stroke square gasoline engine in the performance, emission prediction of range extender engine, standard of charge by using engine and vehicle simulation software tools. In AVL Boost simulation software, range extender engine simulated from 1000 to 6000 rpm engine loads. The highest peak engine power brake reached up to 38 kW at 4500 rpm. On the other hand the highest torque achieved in 100 Nm at 3500 rpm. After that using AVL cruise simulation software, the model of range extended electric vehicle in series configuration with main components such as internal combustion engine, generator, electric motor, battery and the arthemis model rural road cycle was used to simulate the vehicle model. The simulation results show that engine with engine capacity 999 cm3 reported the economical performances of the engine and the emission and the control of engine cycle parameters.

  11. A Novel Range-Extended Strategy for Fuel Cell/Battery Electric Vehicles

    OpenAIRE

    Jenn-Jiang Hwang; Jia-Sheng Hu; Chih-Hong Lin

    2015-01-01

    The range-extended electric vehicle is proposed to improve the range anxiety drivers have of electric vehicles. Conventionally, a gasoline/diesel generator increases the range of an electric vehicle. Due to the zero-CO2 emission stipulations, utilizing fuel cells as generators raises concerns in society. This paper presents a novel charging strategy for fuel cell/battery electric vehicles. In comparison to the conventional switch control, a fuzzy control approach is employed to enhance the ba...

  12. A Novel Range-Extended Strategy for Fuel Cell/Battery Electric Vehicles

    Science.gov (United States)

    Hwang, Jenn-Jiang; Lin, Chih-Hong

    2015-01-01

    The range-extended electric vehicle is proposed to improve the range anxiety drivers have of electric vehicles. Conventionally, a gasoline/diesel generator increases the range of an electric vehicle. Due to the zero-CO2 emission stipulations, utilizing fuel cells as generators raises concerns in society. This paper presents a novel charging strategy for fuel cell/battery electric vehicles. In comparison to the conventional switch control, a fuzzy control approach is employed to enhance the battery's state of charge (SOC). This approach improves the quick loss problem of the system's SOC and thus can achieve an extended driving range. Smooth steering experience and range extension are the main indexes for development of fuzzy rules, which are mainly based on the energy management in the urban driving model. Evaluation of the entire control system is performed by simulation, which demonstrates its effectiveness and feasibility. PMID:26236771

  13. A Novel Range-Extended Strategy for Fuel Cell/Battery Electric Vehicles

    Directory of Open Access Journals (Sweden)

    Jenn-Jiang Hwang

    2015-01-01

    Full Text Available The range-extended electric vehicle is proposed to improve the range anxiety drivers have of electric vehicles. Conventionally, a gasoline/diesel generator increases the range of an electric vehicle. Due to the zero-CO2 emission stipulations, utilizing fuel cells as generators raises concerns in society. This paper presents a novel charging strategy for fuel cell/battery electric vehicles. In comparison to the conventional switch control, a fuzzy control approach is employed to enhance the battery’s state of charge (SOC. This approach improves the quick loss problem of the system’s SOC and thus can achieve an extended driving range. Smooth steering experience and range extension are the main indexes for development of fuzzy rules, which are mainly based on the energy management in the urban driving model. Evaluation of the entire control system is performed by simulation, which demonstrates its effectiveness and feasibility.

  14. A Novel Range-Extended Strategy for Fuel Cell/Battery Electric Vehicles.

    Science.gov (United States)

    Hwang, Jenn-Jiang; Hu, Jia-Sheng; Lin, Chih-Hong

    2015-01-01

    The range-extended electric vehicle is proposed to improve the range anxiety drivers have of electric vehicles. Conventionally, a gasoline/diesel generator increases the range of an electric vehicle. Due to the zero-CO2 emission stipulations, utilizing fuel cells as generators raises concerns in society. This paper presents a novel charging strategy for fuel cell/battery electric vehicles. In comparison to the conventional switch control, a fuzzy control approach is employed to enhance the battery's state of charge (SOC). This approach improves the quick loss problem of the system's SOC and thus can achieve an extended driving range. Smooth steering experience and range extension are the main indexes for development of fuzzy rules, which are mainly based on the energy management in the urban driving model. Evaluation of the entire control system is performed by simulation, which demonstrates its effectiveness and feasibility.

  15. Discrete filtering techniques applied to sequential GPS range measurements

    Science.gov (United States)

    Vangraas, Frank

    1987-01-01

    The basic navigation solution is described for position and velocity based on range and delta range (Doppler) measurements from NAVSTAR Global Positioning System satellites. The application of discrete filtering techniques is examined to reduce the white noise distortions on the sequential range measurements. A second order (position and velocity states) Kalman filter is implemented to obtain smoothed estimates of range by filtering the dynamics of the signal from each satellite separately. Test results using a simulated GPS receiver show a steady-state noise reduction, the input noise variance divided by the output noise variance, of a factor of four. Recommendations for further noise reduction based on higher order Kalman filters or additional delta range measurements are included.

  16. A Voltage Doubler Circuit to Extend the Soft-switching Range of Dual Active Bridge Converters

    DEFF Research Database (Denmark)

    Qin, Zian; Shen, Yanfeng; Wang, Huai

    2017-01-01

    A voltage doubler circuit is realized to extend the soft-switching range of Dual Active Bridge (DAB) converters. No extra hardware is added to the DAB to form this circuit, since it is composed of the dc blocking capacitor and the low side full bridge converter, which already exist in DAB....... With the voltage doubler, the DAB converter can achieve soft switching and high efficiency when the low side dc voltage is close to 2 pu (1 pu is the high side dc voltage divided by the transformer turn ratio), which can be realized only when the low side dc voltage is close to 1 pu by using the conventional phase...... shift modulation in DAB. Thus the soft switching range is extended. The soft switching boundary conditions are derived. A map to show the soft switching or hard switching in the full load and voltage range is obtained. The feasibility and effectiveness of the proposed method is finally verified...

  17. Study on The Extended Range Weather Forecast of Low Frequency Signal Based on Period Analysis Method

    Science.gov (United States)

    Li, X.

    2016-12-01

    Although many studies have explored the MJO and its application for weather forecasting, low-frequency oscillation has been insufficiently studied for the extend range weather forecasting over middle and high latitudes. In China, low-frequency synoptic map is a useful tool for meteorological operation department to forecast extend range weather. It is therefore necessary to develop objective methods to serve the need for finding low-frequency signal, interpretation and application of this signal in the extend range weather forecasting. In this paper, method of Butterworth band pass filter was applied to get low-frequency height field at 500hPa from 1980 to 2014 by using NCEP/NCAR daily grid data. Then period analysis and optimal subset regression methods were used to process the low frequency data of 150 days before the first forecast day and extend the low frequency signal of 500hPa low-frequency high field to future 30 days in the global from June to August during 2011-2014. Finally, the results were test. The main results are as follows: (1) In general, the fitting effect of low frequency signals of 500hPa low-frequency height field by period analysis in the northern hemisphere was better than that in the southern hemisphere, and was better in the low latitudes than that in the high latitudes. The fitting accuracy gradually reduced with the increase of forecast time length, which tended to be stable during the late forecasting period. (2) The fitting effects over the 6 key regions in China showed that except filtering result over Xinjiang area in the first 10 days and 30 days, filtering results over the other 5 key regions throughout the whole period have passed reliability test with level more than 95%. (3) The center and scope of low and high low frequency systems can be fitted well by using the methods mentioned above, which is consist with the corresponding use of the low-frequency synoptic map for the prediction of the extended period. Application of the

  18. A Proportional Resonant Control Strategy for Efficiency Improvement in Extended Range Electric Vehicles

    Directory of Open Access Journals (Sweden)

    Xiaoyuan Wang

    2017-02-01

    Full Text Available The key to control the range extender generation system is to improve the efficiency and reduce the emissions of the electric vehicle (EV. In this paper, based on the purpose of efficiency optimization, both engine and generator are matched to get a public high efficiency region, and a partial power following control strategy was presented. The engine speed is constant in the defined power range, so the output power regulation of the range extender is only realized by the adjustment of the torque of the generator. Engine speed and generator torque were decoupled. An improved proportional resonant (PR controller is adopted to achieve fast output power regulation. In order to ensure the response characteristics of the control system and to improve the robustness, the impacts on system’s characteristics and stability caused by PR controller and parameters in the inner-current loop were analyzed via frequency response characteristics. A pre-Tustin with deviation compensation is proposed for PR controller’s discretization. A stable and robust power following control method is obtained for the range extender control system. Finally, simulation and experiment of the proposed control strategy illustrated its feasibility and correctness.

  19. Summary Report on the SAE 2016 Range Extenders for Electric Vehicles Symposium

    Energy Technology Data Exchange (ETDEWEB)

    Curran, Scott [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Wagner, Robert M. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Campbell, Russ [SRA International, Inc., Arlington, VA (United States)

    2017-03-01

    The SAE 2016 Range Extenders for Electric Vehicles Symposium was a 2-day technical meeting focused on the role of advanced internal combustion engines (ICEs) and other novel energy converter technologies for extending the range of electric vehicles (EVs). The first-of-its-kind symposium was notable for focusing solely on the range extender (REx) technologies and not the EVs. The technical program featured presentations from international leaders from industry, government, national laboratories, and academia. The opening keynote presentations covered a broad range of topics including consumer behavior, policy implications, regulatory considerations, and REx architectures as enablers for advanced technologies. The technical sessions focused on an array of REx technologies including conventional ICEs, as well as less conventional or emerging technologies such as microturbines, fuel cells, low-temperature combustion engines, and aluminum-air batteries. The symposium included two panel sessions. The trend toward increasing vehicle electrification and the changing role of ICEs and other auxiliary power unit technologies for use as REx’s is leading to new research and design development needs. The symposium captured the interest of the industry and research communities in exploring the opportunities and challenges associated with REx’s for EVs. This report includes key takeaways, summarized below, and draft notes for each presentation and panel discussion.

  20. Measuring customer loyalty using an extended RFM and clustering technique

    Directory of Open Access Journals (Sweden)

    Zohre Zalaghi

    2014-05-01

    Full Text Available Today, the ability to identify the profitable customers, creating a long-term loyalty in them and expanding the existing relationships are considered as the key and competitive factors for a customer-oriented organization. The prerequisite for having such competitive factors is the presence of a very powerful customer relationship management (CRM. The accurate evaluation of customers’ profitability is considered as one of the fundamental reasons that lead to a successful customer relationship management. RFM is a method that scrutinizes three properties, namely recency, frequency and monetary for each customer and scores customers based on these properties. In this paper, a method is introduced that obtains the behavioral traits of customers using the extended RFM approach and having the information related to the customers of an organization; it then classifies the customers using the K-means algorithm and finally scores the customers in terms of their loyalty in each cluster. In the suggested approach, first the customers’ records will be clustered and then the RFM model items will be specified through selecting the effective properties on the customers’ loyalty rate using the multipurpose genetic algorithm. Next, they will be scored in each cluster based on the effect that they have on the loyalty rate. The influence rate each property has on loyalty is calculated using the Spearman’s correlation coefficient.

  1. A numerical investigation on the efficiency of range extending systems using Advanced Vehicle Simulator

    Science.gov (United States)

    Varnhagen, Scott; Same, Adam; Remillard, Jesse; Park, Jae Wan

    2011-03-01

    Series plug-in hybrid electric vehicles of varying engine configuration and battery capacity are modeled using Advanced Vehicle Simulator (ADVISOR). The performance of these vehicles is analyzed on the bases of energy consumption and greenhouse gas emissions on the tank-to-wheel and well-to-wheel paths. Both city and highway driving conditions are considered during the simulation. When simulated on the well-to-wheel path, it is shown that the range extender with a Wankel rotary engine consumes less energy and emits fewer greenhouse gases compared to the other systems with reciprocating engines during many driving cycles. The rotary engine has a higher power-to-weight ratio and lower noise, vibration and harshness compared to conventional reciprocating engines, although performs less efficiently. The benefits of a Wankel engine make it an attractive option for use as a range extender in a plug-in hybrid electric vehicle.

  2. Ion Mobility Separation of Variant Histone Tails Extending to the “Middle-down” Range

    Energy Technology Data Exchange (ETDEWEB)

    Shvartsburg, Alexandre A.; Zheng, Yupeng; Smith, Richard D.; Kelleher, Neil

    2012-05-15

    Differential ion mobility spectrometry (FAIMS) can baseline-resolve multiple variants of post-translationally modified peptides extending to the 3 - 4 kDa range, which differ in the localization of a PTM as small as acetylation. Essentially orthogonal separations for different charge states expand the total achievable peak capacity in proportion to the number of observed states that increases for longer polypeptides. This might enable resolving localization variants for even larger peptides and intact proteins.

  3. Long-Range Charge Order in the Extended Holstein-Hubbard Model

    Science.gov (United States)

    Miyao, Tadahiro

    2016-10-01

    This study investigated the extended Holstein-Hubbard model at half-filling as a model for describing the interplay of electron-electron and electron-phonon couplings. When the electron-phonon and nearest-neighbor electron-electron interactions are strong, we prove the existence of long-range charge order in three or more dimensions at a sufficiently low temperature. As a result, we rigorously justify the phase competition between the antiferromagnetism and charge orders.

  4. A plant virus evolved by acquiring multiple nonconserved genes to extend its host range.

    Science.gov (United States)

    Tatineni, Satyanarayana; Robertson, Cecile J; Garnsey, Stephen M; Dawson, William O

    2011-10-18

    Viruses have evolved as combinations of genes whose products interact with cellular components to produce progeny virus throughout the plants. Some viral genes, particularly those that are involved in replication and assembly, tend to be relatively conserved, whereas other genes that have evolved for interactions with the specific host for movement and to counter host-defense systems tend to be less conserved. Closteroviridae encode 1-5 nonconserved ORFs. Citrus tristeza virus (CTV), a Closterovirus, possesses nonconserved p33, p18, and p13 genes that are expendable for systemic infection of the two laboratory hosts, Citrus macrophylla and Mexican lime. In this study, we show that the extended host range of CTV requires these nonconserved genes. The p33 gene was required to systemically infect sour orange and lemon trees, whereas either the p33 or the p18 gene was sufficient for systemic infection of grapefruit trees and the p33 or the p13 gene was sufficient for systemic infection of calamondin plants. Thus, these three genes are required for systemic infection of the full host range of CTV, but different genes were specific for different hosts. Remarkably, either of two genes was sufficient for infection of some citrus hybrids. These findings suggest that CTV acquired multiple nonconserved genes (p33, p18, and p13) and, as a result, gained the ability to interact with multiple hosts, thus extending its host range during the course of evolution. These results greatly extend the complexity of known virus-plant interactions.

  5. A plant virus evolved by acquiring multiple nonconserved genes to extend its host range

    Science.gov (United States)

    Tatineni, Satyanarayana; Robertson, Cecile J.; Garnsey, Stephen M.; Dawson, William O.

    2011-01-01

    Viruses have evolved as combinations of genes whose products interact with cellular components to produce progeny virus throughout the plants. Some viral genes, particularly those that are involved in replication and assembly, tend to be relatively conserved, whereas other genes that have evolved for interactions with the specific host for movement and to counter host–defense systems tend to be less conserved. Closteroviridae encode 1–5 nonconserved ORFs. Citrus tristeza virus (CTV), a Closterovirus, possesses nonconserved p33, p18, and p13 genes that are expendable for systemic infection of the two laboratory hosts, Citrus macrophylla and Mexican lime. In this study, we show that the extended host range of CTV requires these nonconserved genes. The p33 gene was required to systemically infect sour orange and lemon trees, whereas either the p33 or the p18 gene was sufficient for systemic infection of grapefruit trees and the p33 or the p13 gene was sufficient for systemic infection of calamondin plants. Thus, these three genes are required for systemic infection of the full host range of CTV, but different genes were specific for different hosts. Remarkably, either of two genes was sufficient for infection of some citrus hybrids. These findings suggest that CTV acquired multiple nonconserved genes (p33, p18, and p13) and, as a result, gained the ability to interact with multiple hosts, thus extending its host range during the course of evolution. These results greatly extend the complexity of known virus–plant interactions. PMID:21987809

  6. Demonstration of extended capture range for James Webb Space Telescope phase retrieval.

    Science.gov (United States)

    Carlisle, R Elizabeth; Acton, D Scott

    2015-07-20

    A geometrical phase retrieval (GPR) algorithm is applied to the problem of image stacking in order to extend the capture range of normal phase retrieval (PR) on the James Webb Space Telescope (JWST), and potentially eliminate a lengthy image-stacking process that is based on centroids. Computer simulations are used to establish the capture range of the existing PR algorithm for JWST and demonstrate that it is increased by more than a factor of 10 when combined with GPR, guaranteeing PR capture 95% of the time. An experiment using a scale optical model of JWST was conducted to demonstrate the effectiveness of the GPR algorithm in both coherent and incoherent imaging.

  7. Extended motion adaptive signal integration technique for real-time image enhancement

    Science.gov (United States)

    Zhang, David C.; Piacentino, Michael; Chai, Sek

    2012-06-01

    Fast moving cameras often generate distorted and blurred images characterized by reduced sharpness (due to motion blur) and insufficient dynamic range. Reducing sensor integration times to minimize blur are often used but the light intensity and image Signal-to-Noise-Ratio (SNR) would be reduced as well. We propose a Motion Adaptive Signal Integration (MASI) algorithm that operates the sensor at a high frame rate, with real time alignment of individual image frames to form an enhanced quality video output. This technique enables signal integration in the digital domain, allowing both high SNR performance and low motion blur induced by the camera motion. We also show, in an Extended MASI (EMASI) algorithm, that high dynamic range can be achieved by combining high frame rate images of varying exposures. EMASI broadens the dynamic range of the sensor and extends the sensitivity to work in low light and noisy conditions. In a moving platform, it also reduces static noise in the sensor. This technology can be used in aerial surveillance, satellite imaging, border securities, wearable sensing, video conferencing and camera phone imaging applications.

  8. Extending the Effective Ranging Depth of Spectral Domain Optical Coherence Tomography by Spatial Frequency Domain Multiplexing

    Directory of Open Access Journals (Sweden)

    Tong Wu

    2016-11-01

    Full Text Available We present a spatial frequency domain multiplexing method for extending the imaging depth range of a spectral domain optical coherence tomography (SDOCT system without any expensive device. This method uses two galvo scanners with different pivot-offset distances in two independent reference arms for spatial frequency modulation and multiplexing. The spatial frequency contents corresponding to different depth regions of the sample can be shifted to different frequency bands. The spatial frequency domain multiplexing SDOCT system provides an approximately 1.9-fold increase in the effective ranging depth compared with that of a conventional full-range SDOCT system. The reconstructed images of phantom and biological tissue demonstrate the expected increase in ranging depth. The parameters choice criterion for this method is discussed.

  9. Extended Lock Range Zero-Crossing Digital Phase-Locked Loop with Time Delay

    Directory of Open Access Journals (Sweden)

    Nasir Qassim

    2005-01-01

    Full Text Available The input frequency limit of the conventional zero-crossing digital phase-locked loop (ZCDPLL is due to the operating time of the digital circuitry inside the feedback loop. A solution that has been previously suggested is the introduction of a time delay in the feedback path of the loop to allow the digital circuits to complete their sample processing before the next sample is received. However, this added delay will limit the stable operation range and hence lock range of the loop. The objective of this work is to extend the lock range of ZCDPLL with time delay by using a chaos control. The tendency of the loop to diverge is measured and fed back as a form of linear stabilization. The lock range extension has been confirmed through the use of a bifurcation diagram, and Lyapunov exponent.

  10. A study of the sensitivity of long-range passive ranging techniques to atmospheric scintillation

    CSIR Research Space (South Africa)

    De

    2012-04-01

    Full Text Available of the sensitivity of long-range passive ranging techniques to atmospheric scintillation Jason de Villiersa,b, Fintan Wilsona and Fred Nicollsb aCouncil for Scientific and Industrial Research, Pretoria, South Africa; bUniversity of Cape Town, Cape Town, South... and not scintillation and remove it from the list. 6. Interpolate between identified matches to create a complete de-warping mesh for the image. 7. Use de-warping mesh to create stabilised image. 6. RESULTS The resultant depth images in this paper are small in order...

  11. A highly sensitive RF-to-DC power converter with an extended dynamic range

    KAUST Repository

    Almansouri, Abdullah Saud Mohammed

    2017-10-24

    This paper proposes a highly sensitive RF-to-DC power converter with an extended dynamic range that is designed to operate at the medical band 433 MHz and simulated using 0.18 μm CMOS technology. Compared to the conventional fully cross-coupled rectifier, the proposed design offers 3.2× the dynamic range. It is also highly sensitive and requires −18 dBm of input power to produce a 1 V-output voltage when operating with a 100 kΩ load. Furthermore, the proposed design offers an open circuit sensitivity of −23.4 dBm and a peak power conversion efficiency of 67%.

  12. New fabrication techniques for high dynamic range tunneling sensors

    Science.gov (United States)

    Chang, David T.; Stratton, Fred P.; Kubena, Randall L.; Vickers-Kirby, Deborah J.; Joyce, Richard J.; Schimert, Thomas R.; Gooch, Roland W.

    2000-08-01

    We have developed high dynamic range (105-106 g's) tunneling accelerometers1,2 that may be ideal for smart munitions applications by employing both surface and bulk micromachining processing techniques. The highly miniaturized surface-micromachined devices can be manufactured at very low cost and integrated on chip with the control electronics. Bulk-micromachined devices with Si as the cantilever material should have reduced long-term bias drift as well as better stability at higher temperatures. Fully integrated sensors may provide advantages in minimizing microphonics for high-g applications. Previously, we described initial test results using electrostatic forces generated by a self-test electrode located under a Au cantilever3. In this paper, we describe more recent testing of Ni and Au cantilever devices on a shaker table using a novel, low input voltage (5 V) servo controller on both printed wiring board and surface-mount control circuitry. In addition, we report our initial test results for devices packaged using a low-temperature wafer-level vacuum packaging technique for low-cost manufacturing.

  13. Development of a low power miniature linear ion trap mass spectrometer with extended mass range

    Science.gov (United States)

    Li, Gang; Li, Detian; Cheng, Yongjun; Pei, Xiaoqiang; Zhang, Huzhong; Wang, Yongjun; Sun, Jian; Dong, Meng

    2017-12-01

    A miniaturized ion trap mass spectrometer with continuous atmospheric pressure interface was built, which could be used in conjunction with internal ionization (in-vacuum plasma ionization) and external ionization (electrospray ionization). To improve its mass range, a supplemental AC signal frequency scan mode was performed for this miniature mass spectrometer, in which the fundamental RF signal was remained constant with an amplitude as low as several hundreds volts. Experiments showed that the upper limit of the mass range can be extended to 2500 Da for the miniature mass spectrometer developed in this work, and the power consumption can be reduced by 2/5, while maintaining good balance with performance parameters such as stability, sensitivity, and resolution. Due to the improvement in mass range and significant reduction in energy consumption compared with the instrument using the traditional resonant ejection mode, the scan method developed in this work is helpful to promote the miniature design of mass spectrometers for field analysis and space exploration.

  14. Using two dyes with the same fluorophore to monitor cellular calcium concentration in an extended range.

    Directory of Open Access Journals (Sweden)

    Lourdes Figueroa

    Full Text Available We extend the sensitivity of quantitative concentration imaging to an approximately 1000-fold range of concentrations by a method that uses two fluorescent dyes with the same fluorophore, having different affinity for the monitored species. While the formulation and illustration refer to a monitor of calcium concentration, the method is applicable to any species that binds to multiple indicators with the same spectral properties. The use of a common fluorophore has the virtue of leaving vast regions of the electromagnetic spectrum available for other applications. We provide the exact analytic expression relating measured fluorescence to [Ca(2+] at equilibrium and an approximate analytic expression that does not require the equilibrium assumption. The sensitivity of the method is calculated numerically for two useful dye pairs. As illustrative application of the enhanced measurement, we use fluo-4 and fluo-4FF to image the calcium wave produced by a cardiac myocyte in response to a small artificial calcium spark.

  15. Lightweight Investigation of Extended-Range Electric Vehicle Based on Collision Failure Using Numerical Simulation

    Directory of Open Access Journals (Sweden)

    Jiangqi Long

    2015-01-01

    Full Text Available The total weight of Extended-Range Electric Vehicle (E-REV is too heavy, which affects rear-end collision safety. Using numerical simulation, a lightweight method is designed to reduce E-REV body and key parts weight based on rear-end collision failure analysis. To calculate and optimize the performance of vehicle safety, the simulation model of E-REV rear-end collision safety is built by using finite element analysis. Drive battery pack lightweight design method is analyzed and the bending mode and torsional mode of E-REV before and after lightweight are compared to evaluate E-REV rear-end collision safety performance. The simulation results of optimized E-REV safety structure are verified by both numerical simulation and experimental investigation of the entire vehicle crash test.

  16. True coincidence summing corrections for an extended energy range HPGe detector

    Energy Technology Data Exchange (ETDEWEB)

    Venegas-Argumedo, Y. [Centro de Investigación en Materiales Avanzados (CIMAV), Miguel de Cervantes 120, Chihuahua, Chih 31109 (Mexico); M.S. Student at CIMAV (Mexico); Montero-Cabrera, M. E., E-mail: elena.montero@cimav.edu.mx [Centro de Investigación en Materiales Avanzados (CIMAV), Miguel de Cervantes 120, Chihuahua, Chih 31109 (Mexico)

    2015-07-23

    True coincidence summing (TCS) effect for natural radioactive families of U-238 and Th-232 represents a problem when an environmental sample with a close source-detector geometry measurement is performed. By using a certified multi-nuclide standard source to calibrate an energy extended range (XtRa) HPGe detector, it is possible to obtain an intensity spectrum slightly affected by the TCS effect with energies from 46 to 1836 keV. In this work, the equations and some other considerations required to calculate the TCS correction factor for isotopes of natural radioactive chains are described. It is projected a validation of the calibration, performed with the IAEA-CU-2006-03 samples (soil and water)

  17. Close-Range Sensing Techniques in Alpine Terrain

    Science.gov (United States)

    Rutzinger, M.; Höfle, B.; Lindenbergh, R.; Oude Elberink, S.; Pirotti, F.; Sailer, R.; Scaioni, M.; Stötter, J.; Wujanz, D.

    2016-06-01

    Early career researchers such as PhD students are a main driving force of scientific research and are for a large part responsible for research innovation. They work on specialized topics within focused research groups that have a limited number of members, but might also have limited capacity in terms of lab equipment. This poses a serious challenge for educating such students as it is difficult to group a sufficient number of them to enable efficient knowledge transfer. To overcome this problem, the Innsbruck Summer School of Alpine Research 2015 on close-range sensing techniques in Alpine terrain was organized in Obergurgl, Austria, by an international team from several universities and research centres. Of the applicants a group of 40 early career researchers were selected with interest in about ten types of specialized surveying tools, i.e. laser scanners, a remotely piloted aircraft system, a thermal camera, a backpack mobile mapping system and different grade photogrammetric equipment. During the one-week summer school, students were grouped according to their personal preference to work with one such type of equipment under guidance of an expert lecturer. All students were required to capture and process field data on a mountain-related theme like landslides or rock glaciers. The work on the assignments lasted the whole week but was interspersed with lectures on selected topics by invited experts. The final task of the summer school participants was to present and defend their results to their peers, lecturers and other colleagues in a symposium-like setting. Here we present the framework and content of this summer school which brought together scientists from close-range sensing and environmental and geosciences.

  18. Extending the Range of Beer's Law in Ft-Ir Spectrometry

    Science.gov (United States)

    Zhu, Changjiang

    1995-01-01

    The photometric accuracy of any type of spectrometer depends on the ratio of the resolution to the full width at half height of the analytical band, often called the resolution parameter, rho. Apodization functions are used widely in Fourier transform infrared (FT-IR) spectrometry to change the instrument line shape function. For Lorentzian bands measured with a triangular apodization function, there is a negative deviation from Beer's law at high true peak absorbance even when rho project, the possibility of extending the linear range of Beer's law by applying "optimized" apodization functions of the type proposed by Norton and Beer and three continuous functions has been investigated. A theoretical study showed that the linear range of Beer's law plots for spectra measured at moderate resolution can be extended to peak absorbance greater than 2 with the use of both continuous and discontinuous (Norton-Beer) apodization functions. Linear plots of the apparent absorbance of a band against analyte concentration can be obtained even for bands of absorbance substantially greater than 3, although the intercept on the absorbance axis may not be at zero. Spectra of benzonitrile and cyclohexane dissolved in carbon tetrachloride were measured on four FT-IR spectrometers in an experimental investigation designed to verify the results of these theoretical studies. The values of apparent peak absorbance with the four instruments showed that good linearity could be attained over limited absorbance ranges on all four instruments. Significant differences between the measured absorbance values and the apparent absorbance calculated in the theoretical study were observed for bands with peak absorbance greater than 2.0 for three of the four instruments. Whether positive or negative deviations from Beer's law were observed depended on the spectrometer being used for the measurement. Several other experimental factors affecting the performance of Beer's law in practice were also

  19. Designed-seamless irradiation technique for extended whole mediastinal proton-beam irradiation for esophageal cancer

    Directory of Open Access Journals (Sweden)

    Okonogi Noriyuki

    2012-10-01

    Full Text Available Abstract Background Proton-beam therapy (PBT provides therapeutic advantages over conformal x-ray therapy in sparing organs at risk when treating esophageal cancer because of the fundamental physical dose distribution of the proton-beam. However, cases with extended esophageal lesions are difficult to treat with conventional PBT with a single isocentric field, as the length of the planning target volume (PTV is longer than the available PBT field size in many facilities. In this study, the feasibility of a practical technique to effectively match PBT fields for esophageal cancer with a larger regional field beyond the available PBT field size was investigated. Methods Twenty esophageal cancer patients with a larger regional field than the available PBT single-field size (15 cm in our facility were analyzed. The PTV was divided into two sections to be covered by a single PBT field. Subsequently, each PTV isocenter was aligned in a cranial-caudal (CC axis to rule out any influence by the movement of the treatment couch in anterior-posterior and left-right directions. To obtain the appropriate dose distributions, a designed-seamless irradiation technique (D-SLIT was proposed. This technique requires the following two adjustments: (A blocking a part of the PTV by multi-leaf collimator(s (MLCs; and (B fine-tuning the isocenter distance by the half-width of the MLC leaf (2.5 mm in our facility. After these steps, the inferior border of the cranial field was designed to match the superior border of the caudal field. Dose distributions along the CC axis around the field junction were evaluated by the treatment-planning system. Dose profiles were validated with imaging plates in all cases. Results The average and standard deviation of minimum dose, maximum dose, and dose range between maximum and minimum doses around the field junction by the treatment-planning system were 95.9 ± 3.2%, 105.3 ± 4.1%, and 9.4 ± 5.2%. The dose profile validated by the

  20. Design, calibration and tests of an extended-range Bonner sphere spectrometer

    CERN Document Server

    Mitaroff, Angela; Silari, Marco

    2001-01-01

    Stray radiation fields outside the shielding of hadron accelerators are of complex nature. They consist of a multiplicity of radiation components (neutrons, photons, electrons, pions, muons, ...) which extend over a wide range of energies. Since the dose equivalent in these mixed fields is mainly due to neutrons, neutron dosimetry is a particularly important task. The neutron energy in these fields ranges from thermal up to several hundreds of MeV, thus making dosimetry difficult. A well known instrument for measuring neutron energy distributions from thermal energies up to about E=10 MeV is the Bonner sphere spectrometer (BSS). It consists of a set of moderating spheres of different radii made of polyethylene, with a thermal neutron counter in the centre. Each detector (sphere plus counter) has a maximum response at a certain energy value depending on its size, but the overall response of the conventional BSS drops sharply between E=10-20 MeV. This thesis focuses on the development, the calibration and tests...

  1. Shear-band capturing using a multiscale extended digital image correlation technique

    OpenAIRE

    Réthoré, Julien; Hild, François; Roux, Stéphane

    2007-01-01

    International audience; Finite elements have been used recently to solve the optical flow conservation principle invoked to determine displacement fields by digital image correlation. Inspired by these recent advances, and by the computational effort that has been accomplished during the past 10 years for the simulation of discontinuities by the eXtended Finite Element Method (XFEM), an extended correlation technique is introduced for capturing shear-band like discontinuities from images of r...

  2. On Formal Methods for Collective Adaptive System Engineering. Scalable Approximated, Spatial Analysis Techniques. Extended Abstract.

    Directory of Open Access Journals (Sweden)

    Diego Latella

    2016-07-01

    Full Text Available In this extended abstract a view on the role of Formal Methods in System Engineering is briefly presented. Then two examples of useful analysis techniques based on solid mathematical theories are discussed as well as the software tools which have been built for supporting such techniques. The first technique is Scalable Approximated Population DTMC Model-checking. The second one is Spatial Model-checking for Closure Spaces. Both techniques have been developed in the context of the EU funded project QUANTICOL.

  3. Dem Generation from Close-Range Photogrammetry Using Extended Python Photogrammetry Toolbox

    Science.gov (United States)

    Belmonte, A. A.; Biong, M. M. P.; Macatulad, E. G.

    2017-10-01

    Digital elevation models (DEMs) are widely used raster data for different applications concerning terrain, such as for flood modelling, viewshed analysis, mining, land development, engineering design projects, to name a few. DEMs can be obtained through various methods, including topographic survey, LiDAR or photogrammetry, and internet sources. Terrestrial close-range photogrammetry is one of the alternative methods to produce DEMs through the processing of images using photogrammetry software. There are already powerful photogrammetry software that are commercially-available and can produce high-accuracy DEMs. However, this entails corresponding cost. Although, some of these software have free or demo trials, these trials have limits in their usable features and usage time. One alternative is the use of free and open-source software (FOSS), such as the Python Photogrammetry Toolbox (PPT), which provides an interface for performing photogrammetric processes implemented through python script. For relatively small areas such as in mining or construction excavation, a relatively inexpensive, fast and accurate method would be advantageous. In this study, PPT was used to generate 3D point cloud data from images of an open pit excavation. The PPT was extended to add an algorithm converting the generated point cloud data into a usable DEM.

  4. DEM GENERATION FROM CLOSE-RANGE PHOTOGRAMMETRY USING EXTENDED PYTHON PHOTOGRAMMETRY TOOLBOX

    Directory of Open Access Journals (Sweden)

    A. A. Belmonte

    2017-10-01

    Full Text Available Digital elevation models (DEMs are widely used raster data for different applications concerning terrain, such as for flood modelling, viewshed analysis, mining, land development, engineering design projects, to name a few. DEMs can be obtained through various methods, including topographic survey, LiDAR or photogrammetry, and internet sources. Terrestrial close-range photogrammetry is one of the alternative methods to produce DEMs through the processing of images using photogrammetry software. There are already powerful photogrammetry software that are commercially-available and can produce high-accuracy DEMs. However, this entails corresponding cost. Although, some of these software have free or demo trials, these trials have limits in their usable features and usage time. One alternative is the use of free and open-source software (FOSS, such as the Python Photogrammetry Toolbox (PPT, which provides an interface for performing photogrammetric processes implemented through python script. For relatively small areas such as in mining or construction excavation, a relatively inexpensive, fast and accurate method would be advantageous. In this study, PPT was used to generate 3D point cloud data from images of an open pit excavation. The PPT was extended to add an algorithm converting the generated point cloud data into a usable DEM.

  5. Extended-Range Ensemble Predictions of Convection in the North Australian Monsoon Region

    Science.gov (United States)

    Drosdowsky, Wasyl; Wheeler, Matthew C.

    2017-04-01

    Extended-range (Bureau of Meteorology’s Predictive Ocean-Atmosphere Model for Australia (POAMA). Hindcasts from 1980-2011 are used, initialised on the 1st, 11th and 21st of each month, with a 33-member ensemble. The measure of convection is outgoing longwave radiation (OLR) averaged over the box 120ºE-150ºE, 5ºS-17.5ºS. This averaging serves to focus on the intraseasonal and longer time scales, and is an area of interest to users. The raw hindcasts of daily OLR show a strong systematic adjustment away from their initial values during the first week, and then converge to a mean seasonal cycle of similar amplitude and phase to observations. Hence, forecast OLR anomalies are formed by removing the model’s own seasonal cycle of OLR, which is a function of start time and lead time, a usual practice for dynamical seasonal prediction. Over all hindcasts, the model forecast root-mean-square (RMS) error is smaller than the RMS error of persistence and climatological reference forecasts for leads 3-35 days. Ensemble spread is less than the forecast RMS error (i.e. under-spread) for days 1-12, but slightly greater than the RMS error for longer leads. Binning the individual forecasts based on ensemble spread shows a generally positive relationship between spread and error. Therefore, greater certainty can be given for forecasts with smaller spread.

  6. New records of Lophoproctuscoecus Pocock, 1894 (Diplopoda, Polyxenida, Lophoproctidae) extend the range of the genus Lophoproctus.

    Science.gov (United States)

    Short, Megan

    2015-01-01

    The geographic distribution of the genus Lophoproctus Pocock, 1894 has greatly expanded with new records of the species Lophoproctuscoecus Pocock, 1894, together with the reassignment of a number of millipedes formerly identified as Lophoproctuslucidus (Chalande, 1888). Lophoproctuscoecus was found to be the sole representative of the family Lophoproctidae in collections examined from Crimea and the Caucasian region. The species was also identified from Iran and Kyrgyzstan. Lophoproctus specimens collected in Italy by Verhoeff were reassigned as Lophoproctuscoecus with the exception of one specimen of Lophoproctusjeanneli (Brölemann, 1910) from Capri. These data were combined with all available information from the literature to look at the pattern of distribution of the four species in the genus. The range of the genus Lophoproctus extends from Portugal to Central Asia. Lophoproctuscoecus is widespread from Italy eastward, while the morphologically very similar species Lophoproctuslucidus is confined to France and northern Africa. The two species have a narrow overlap in the Alpes Maritimes region of France. Lophoproctusjeanneli has a scattered coastal distribution around the Mediterranean Sea. The troglobitic species Lophoproctuspagesi (Condé, 1982) has only been recorded from a cave on Majorca, Spain.

  7. Range Surveillance Using Radio Interferometry and TDOA Techniques Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The proposed innovation will utilize a small network of remote sensors to perform Radio Interferometry (RI) and Time Difference of Arrival (TDOA) techniques to...

  8. Calibration and assessment of channel-specific biases in microarray data with extended dynamical range

    Directory of Open Access Journals (Sweden)

    Vallon-Christersson Johan

    2004-11-01

    with extended dynamical range and better precision. The cross-platform R package aroma, which implements all described methods, is available for free from http://www.maths.lth.se/bioinformatics/.

  9. Solving Inverse Kinematics – A New Approach to the Extended Jacobian Technique

    Directory of Open Access Journals (Sweden)

    M. Šoch

    2005-01-01

    Full Text Available This paper presents a brief summary of current numerical algorithms for solving the Inverse Kinematics problem. Then a new approach based on the Extended Jacobian technique is compared with the current Jacobian Inversion method. The presented method is intended for use in the field of computer graphics for animation of articulated structures. 

  10. Extended calibration range for prompt photon emission in ion beam irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Bellini, F. [Dipartimento di Fisica, Sapienza Università di Roma, Roma (Italy); INFN Sezione di Roma, Roma (Italy); Boehlen, T.T.; Chin, M.P.W. [CERN, Geneva (Switzerland); Collamati, F. [Dipartimento di Fisica, Sapienza Università di Roma, Roma (Italy); INFN Sezione di Roma, Roma (Italy); De Lucia, E. [Laboratori Nazionali di Frascati dell' INFN, Frascati (Italy); Faccini, R., E-mail: riccardo.faccini@roma1.infn.it [Dipartimento di Fisica, Sapienza Università di Roma, Roma (Italy); INFN Sezione di Roma, Roma (Italy); Ferrari, A. [CERN, Geneva (Switzerland); Lanza, L. [Dipartimento di Fisica, Sapienza Università di Roma, Roma (Italy); INFN Sezione di Roma, Roma (Italy); Mancini-Terracciano, C. [CERN, Geneva (Switzerland); Dipartimento di Fisica, Università Roma Tre, Roma (Italy); Marafini, M. [Museo Storico della Fisica e Centro Studi e Ricerche “E. Fermi”, Roma (Italy); INFN Sezione di Roma, Roma (Italy); Mattei, I. [Dipartimento di Fisica, Università Roma Tre, Roma (Italy); Laboratori Nazionali di Frascati dell' INFN, Frascati (Italy); Morganti, S. [INFN Sezione di Roma, Roma (Italy); Ortega, P.G. [CERN, Geneva (Switzerland); Patera, V. [Dipartimento di Scienze di Base e Applicate per Ingegneria, Sapienza Università di Roma, Roma (Italy); INFN Sezione di Roma, Roma (Italy); Piersanti, L. [Dipartimento di Scienze di Base e Applicate per Ingegneria, Sapienza Università di Roma, Roma (Italy); Laboratori Nazionali di Frascati dell' INFN, Frascati (Italy); Russomando, A. [Center for Life Nano Science@Sapienza, Istituto Italiano di Tecnologia, Roma (Italy); INFN Sezione di Roma, Roma (Italy); Sala, P.R. [INFN Sezione di Milano, Milano (Italy); and others

    2014-05-01

    Monitoring the dose delivered during proton and carbon ion therapy is still a matter of research. Among the possible solutions, several exploit the measurement of the single photon emission from nuclear decays induced by the irradiation. To fully characterize such emission the detectors need development, since the energy spectrum spans the range above the MeV that is not traditionally used in medical applications. On the other hand, a deeper understanding of the reactions involving gamma production is needed in order to improve the physic models of Monte Carlo codes, relevant for an accurate prediction of the prompt-gamma energy spectrum. This paper describes a calibration technique tailored for the range of energy of interest and reanalyzes the data of the interaction of a 80 MeV/u fully stripped carbon ion beam with a Poly-methyl methacrylate target. By adopting the FLUKA simulation with the appropriate calibration and resolution a significant improvement in the agreement between data and simulation is reported.

  11. Extended calibration range for prompt photon emission in ion beam irradiation

    CERN Document Server

    Bellini, F.

    2014-01-01

    Monitoring the dose delivered during proton and carbon ion therapy is still a matter of research. Among the possible solutions, several exploit the measurement of the single photon emission from nuclear decays induced by the irradiation. To fully characterize such emission the detectors need development, since the energy spectrum spans the range above the MeV that is not traditionally used in medical applications. On the other hand, a deeper understanding of the reactions involving gamma production is needed in order to improve the physic models of Monte Carlo codes, relevant for an accurate prediction of the prompt-gamma energy spectrum.This paper describes a calibration technique tailored for the range of energy of interest and reanalyzes the data of the interaction of a 80MeV/u fully stripped carbon ion beam with a Poly-methyl methacrylate target. By adopting the FLUKA simulation with the appropriate calibration and resolution a significant improvement in the agreement between data and simulation is report...

  12. Comparison of visual outcomes after bilateral implantation of extended range of vision and trifocal intraocular lenses.

    Science.gov (United States)

    Ruiz-Mesa, Ramón; Abengózar-Vela, Antonio; Aramburu, Ana; Ruiz-Santos, María

    2017-06-26

    To compare visual outcomes after cataract surgery with bilateral implantation of 2 intraocular lenses (IOLs): extended range of vision and trifocal. Each group of this prospective study comprised 40 eyes (20 patients). Phacoemulsification followed by bilateral implantation of a FineVision IOL (group 1) or a Symfony IOL (group 2) was performed. The following outcomes were assessed up to 1 year postoperatively: binocular uncorrected distance visual acuity (UDVA), binocular uncorrected intermediate visual acuity (UIVA) at 60 cm, binocular uncorrected near visual acuity (UNVA) at 40 cm, spherical equivalent (SE) refraction, defocus curves, mesopic and photopic contrast sensitivity, halometry, posterior capsule opacification (PCO), and responses to a patient questionnaire. The mean binocular values in group 1 and group 2, respectively, were SE -0.15 ± 0.25 D and -0.19 ± 0.18 D; UDVA 0.01 ± 0.03 logMAR and 0.01 ± 0.02 logMAR; UIVA 0.11 ± 0.08 logMAR and 0.09 ± 0.08 logMAR; UNVA 0.06 ± 0.07 logMAR and 0.17 ± 0.06 logMAR. Difference in UNVA between IOLs (p<0.05) was statistically significant. There were no significant differences in contrast sensitivity, halometry, or PCO between groups. Defocus curves were similar between groups from 0 D to -2 D, but showed significant differences from -2.50 D to -4.00 D (p<0.05). Both IOLs provided excellent distance and intermediate visual outcomes. The FineVision IOL showed better near visual acuity. Predictability of the refractive results and optical performance were excellent; all patients achieved spectacle independence. The 2 IOLs gave similar and good contrast sensitivity in photopic and mesopic conditions and low perception of halos by patients.

  13. Reference ranges for interrupter resistance technique: the Asthma UK Initiative.

    NARCIS (Netherlands)

    Merkus, P.J.F.M.; Stocks, J.; Beydon, N.; Lombardi, E.; Jones, M.; McKenzie, S.A.; Kivastik, J.; Arets, B.G.; Stanojevic, S.

    2010-01-01

    Measuring interrupter resistance (R(int)) is an increasingly popular lung function technique and especially suitable for preschool children because it is simple, quick and requires only passive cooperation. A European Respiratory Society (ERS)/American Thoracic Society (ATS) Task Force recently

  14. Biexponential characterization of prostate tissue water diffusion decay curves over an extended b-factor range.

    Science.gov (United States)

    Mulkern, Robert V; Barnes, Agnieszka Szot; Haker, Steven J; Hung, Yin P; Rybicki, Frank J; Maier, Stephan E; Tempany, Clare M C

    2006-06-01

    Detailed measurements of water diffusion within the prostate over an extended b-factor range were performed to assess whether the standard assumption of monoexponential signal decay is appropriate in this organ. From nine men undergoing prostate MR staging examinations at 1.5 T, a single 10-mm-thick axial slice was scanned with a line scan diffusion imaging sequence in which 14 equally spaced b factors from 5 to 3,500 s/mm(2) were sampled along three orthogonal diffusion sensitization directions in 6 min. Due to the combination of long scan time and limited volume coverage associated with the multi-b-factor, multidirectional sampling, the slice was chosen online from the available T2-weighted axial images with the specific goal of enabling the sampling of presumed noncancerous regions of interest (ROIs) within the central gland (CG) and peripheral zone (PZ). Histology from prescan biopsy (n=9) and postsurgical resection (n=4) was subsequently employed to help confirm that the ROIs sampled were noncancerous. The CG ROIs were characterized from the T2-weighted images as primarily mixtures of glandular and stromal benign prostatic hyperplasia, which is prevalent in this population. The water signal decays with b factor from all ROIs were clearly non-monoexponential and better served with bi- vs. monoexponential fits, as tested using chi(2)-based F test analyses. Fits to biexponential decay functions yielded intersubject fast diffusion component fractions in the order of 0.73+/-0.08 for both CG and PZ ROIs, fast diffusion coefficients of 2.68+/-0.39 and 2.52+/-0.38 microm(2)/ms and slow diffusion coefficients of 0.44+/-0.16 and 0.23+/-0.16 um(2)/ms for CG and PZ ROIs, respectively. The difference between the slow diffusion coefficients within CG and PZ was statistically significant as assessed with a Mann-Whitney nonparametric test (P<.05). We conclude that a monoexponential model for water diffusion decay in prostate tissue is inadequate when a large range of b

  15. Utility of ionosphere and troposphere models for extending the range of high-accuracy GPS

    Science.gov (United States)

    Dodd, David William

    This dissertation studied the use of NOAA real-time ionosphere and troposphere products in extending the range of long-baseline, high-accuracy DGPS for real-time positioning. The question being addressed by this work is; can existing real-time ionosphere and troposphere models reduce the observation uncertainties to the level where they can be used to reliably resolve integer ambiguities, in real-time, over long baselines (>30km). In-house GPS processing software (USM_OTF) was developed to ingest the models and compute epoch-to-epoch, float and fixed ambiguity position solutions. Single baseline processing, ranging from 20 to 740 kin, over several days in four separate sessions (July 2004, January 2005, August 2005 and July 2006) incorporating four regions of the U.S.A. (Michigan, California, Central and the South East), were evaluated. The first session looked at the NOAA real-time troposphere model and the second session looked at the NOAA real-time ionosphere model. The third and fourth sessions looked at the use of both the NOAA real-time ionosphere and troposphere models. Results showed that the NOAA troposphere model reduced the height bias uncertainty by up to 30 cm, under high activity conditions. They also showed that the troposphere model increased the uncertainty standard deviation under these high activity conditions. The results from the first tests of the real-time NOAA ionosphere model showed that, due to satellite coverage issues, it produced worse results than other real-time models. The NOAA model suffered from lack of satellite coverage corrections, especially in areas near the limits of the model, and at the beginning and end of a satellite's flight path. A reduction in satellite numbers lead to weaker geometry and less reliable position solutions. These tests showed that it was better to provide less accurate ionosphere estimates than to leave the satellites out of the solution. These problems were addressed by NOAA prior to the final tests

  16. Infrared optical element mounting techniques for wide temperature ranges.

    Science.gov (United States)

    Saggin, Bortolino; Tarabini, Marco; Scaccabarozzi, Diego

    2010-01-20

    We describe the optimization of a mounting system for the infrared (IR) optics of a spaceborne interferometer working in the temperature range between -120 degrees C and +150 degrees C. The concept is based on an aluminum alloy frame with designed mechanical compliance, which allows for compensation of the different coefficient of thermal expansion between the optics and the holder; at the same time, the system provides for the high stiffness required to reach natural frequencies above 200 Hz, which are mandatory in most space missions. Thermal adapters with properly chosen thermomechanical characteristics are interposed between the metallic structure and the lens, so as to reduce the interface stresses on the mechanically weak IR material, due to both the thermoelastic and acceleration loads. With the proposed mount, the competitive requirements of stiffness and stress-free mounting can be matched in wide temperature ranges. The case study of the interferometer of a miniaturized Fourier transform IR spectrometer is presented.

  17. Heat wave over India during summer 2015: an assessment of real time extended range forecast

    Science.gov (United States)

    Pattanaik, D. R.; Mohapatra, M.; Srivastava, A. K.; Kumar, Arun

    2017-08-01

    Hot winds are the marked feature of summer season in India during late spring preceding the climatological onset of the monsoon season in June. Some years the conditions becomes very vulnerable with the maximum temperature ( T max) exceeding 45 °C for many days over parts of north-western, eastern coastal states of India and Indo-Gangetic plain. During summer of 2015 (late May to early June) eastern coastal states, central and northwestern parts of India experienced severe heat wave conditions leading to loss of thousands of human life in extreme high temperature conditions. It is not only the loss of human life but also the animals and birds were very vulnerable to this extreme heat wave conditions. In this study, an attempt is made to assess the performance of real time extended range forecast (forecast up to 3 weeks) of this scorching T max based on the NCEP's Climate Forecast System (CFS) latest version coupled model (CFSv2). The heat wave condition was very severe during the week from 22 to 28 May with subsequent week from 29 May to 4 June also witnessed high T max over many parts of central India including eastern coastal states of India. The 8 ensemble members of operational CFSv2 model are used once in a week to prepare the weekly bias corrected deterministic (ensemble mean) T max forecast for 3 weeks valid from Friday to Thursday coinciding with the heat wave periods of 2015. Using the 8 ensemble members separately and the CFSv2 corresponding hindcast climatology the probability of above and below normal T max is also prepared for the same 3 weeks. The real time deterministic and probabilistic forecasts did indicate impending heat wave over many parts of India during late May and early June of 2015 associated with strong northwesterly wind over main land mass of India, delaying the sea breeze, leading to heat waves over eastern coastal regions of India. Thus, the capability of coupled model in providing early warning of such killer heat wave can be very

  18. Prediction of kharif rice yield at Kharagpur using disaggregated extended range rainfall forecasts

    Science.gov (United States)

    Dhekale, B. S.; Nageswararao, M. M.; Nair, Archana; Mohanty, U. C.; Swain, D. K.; Singh, K. K.; Arunbabu, T.

    2017-08-01

    The Extended Range Forecasts System (ERFS) has been generating monthly and seasonal forecasts on real-time basis throughout the year over India since 2009. India is one of the major rice producer and consumer in South Asia; more than 50% of the Indian population depends on rice as staple food. Rice is mainly grown in kharif season, which contributed 84% of the total annual rice production of the country. Rice cultivation in India is rainfed, which depends largely on rains, so reliability of the rainfall forecast plays a crucial role for planning the kharif rice crop. In the present study, an attempt has been made to test the reliability of seasonal and sub-seasonal ERFS summer monsoon rainfall forecasts for kharif rice yield predictions at Kharagpur, West Bengal by using CERES-Rice (DSSATv4.5) model. These ERFS forecasts are produced as monthly and seasonal mean values and are converted into daily sequences with stochastic weather generators for use with crop growth models. The daily sequences are generated from ERFS seasonal (June-September) and sub-seasonal (July-September, August-September, and September) summer monsoon (June to September) rainfall forecasts which are considered as input in CERES-rice crop simulation model for the crop yield prediction for hindcast (1985-2008) and real-time mode (2009-2015). The yield simulated using India Meteorological Department (IMD) observed daily rainfall data is considered as baseline yield for evaluating the performance of predicted yields using the ERFS forecasts. The findings revealed that the stochastic disaggregation can be used to disaggregate the monthly/seasonal ERFS forecasts into daily sequences. The year to year variability in rice yield at Kharagpur is efficiently predicted by using the ERFS forecast products in hindcast as well as real time, and significant enhancement in the prediction skill is noticed with advancement in the season due to incorporation of observed weather data which reduces uncertainty of

  19. Long Range Microimage Transmission Techniques Study for AFMPC

    Science.gov (United States)

    1979-10-01

    of MIT Cambridge, Massa- chusetts, and EPSCO Laboratories ( now defunct) in Wilton, Connecticut. Their results indicate that the long range... EPSCO Laboratories (now defunrt) in Wilton, Connecticut. The NOSC effort was sponsored by the Bureau of Naval Personnel, the ESL effort was conducted...in support of the Library of Congress and the EPSCO Laboratory effort was sponsored by RADC in support of the Foreign Technology Division at Wright

  20. Design, Fabrication and Prototype testing of a Chip Integrated Micro PEM Fuel Cell Accumulator combined On-Board Range Extender

    Science.gov (United States)

    Balakrishnan, A.; Mueller, C.; Reinecke, H.

    2014-11-01

    In this work we present the design, fabrication and prototype testing of Chip Integrated Micro PEM Fuel Cell Accumulator (CIμ-PFCA) combined On-Board Range Extender (O-BRE). CIμ-PFCA is silicon based micro-PEM fuel cell system with an integrated hydrogen storage feature (palladium metal hydride), the run time of CIμ-PFCA is dependent on the stored hydrogen, and in order to extend its run time an O-BRE is realized (catalytic hydrolysis of chemical hydride, NaBH4. Combining the CIμ-PFCA and O-BRE on a system level have few important design requirements to be considered; hydrogen regulation, gas -liquid separator between the CIμ-PFCA and the O-RE. The usage of traditional techniques to regulate hydrogen (tubes), gas-liquid phase membranes (porous membrane separators) are less desirable in the micro domain, due to its space constraint. Our approach is to use a passive hydrogen regulation and gas-liquid phase separation concept; to use palladium membrane. Palladium regulates hydrogen by concentration diffusion, and its property to selectively adsorb only hydrogen is used as a passive gas-liquid phase separator. Proof of concept is shown by realizing a prototype system. The system is an assembly of CIμ-PFCA, palladium membrane and the O-BRE. The CIμ-PFCA consist of 2 individually processed silicon chips, copper supported palladium membrane realized by electroplating followed by high temperature annealing process under inter atmosphere and the O-BRE is realized out of a polymer substrate by micromilling process with platinum coated structures, which functions as a catalyst for the hydrolysis of NaBH4. The functionality of the assembled prototype system is demonstrated by the measuring a unit cell (area 1 mm2) when driven by the catalytic hydrolysis of chemical hydride (NaBH4 and the prototype system shows run time more than 15 hours.

  1. Automatic out-of-range photo recognition using digital techniques

    Science.gov (United States)

    Dardier, Genevieve; Maitre, Henri

    1998-09-01

    This paper addresses digital techniques used to identify automatically those color photographs whose optical densities fall outside acceptable norms for a visual system. Targets are of two different kinds indicating the need for different recognition algorithms. First, the investigation focuses on color pictures showing high contrast in optical densities such as pictures taken with flash and pictures taken against the light; it estimates statistical parameters which determine mixture densities. Results of Maximum Likelihood, Moment estimation using Prony's Method, Multiscale Analysis and Marquardt optimization algorithm applied to the histogram recognition problem have been compared in terms of efficiency and speed for both low and more detailed vision. Attention is then focussed on pictures showing an optical density gradient in a given direction. Solutions such as plane fitting, robust Median Based Estimator are compared with a new '4-step Median Based Estimator.'

  2. Measurement of soil water potential over an extended range by polymer tensiometers: comparison with other instruments

    Science.gov (United States)

    van der Ploeg, M. J.; Gooren, H. P.; Hoogendam, R. C.; Bakker, G.; Huiskes, C.; Koopal, L. K.; Kruidhof, H.; de Rooij, G. H.

    2007-12-01

    In water scarce areas, plant growth and productivity can be severely hampered by irregular precipitation and overall water shortage. Root water uptake is mainly driven by matric potential gradients, but measurement of soil water matric potential is limited by the measurement range of water-filled tensiometers (-0.085 MPa). Other measurement techniques indirectly measure soil water potential by converting soil water content with the use of the water retention curve. In dry soils, the water content measurements may become insensitive to small variations, and consequently this conversion may lead to large errors. We developed a polymer tensiometer (POT) that is able to measure matric potentials down to -2.0 MPa. The POT consists of a solid ceramic, a stainless steel cup and a pressure transducer. The ceramic consist of a support layer and a membrane with 2 nm pore-size to prevent polymer leakage. Between the ceramic membrane and the pressure transducer a tiny chamber is located, which contains the polymer solution. The polymer's osmotic potential strongly reduces the total water potential inside the polymer tensiometer, which causes build-up of osmotic pressure. Hence, the water in the polymer tensiometer will cavitate at a much lower matric potential than the nearly pure water in a conventional tensiometer. Direct observation of the potential of soil water at different locations in the root-system will yield knowledge about the ability of a plant to take up the water under conditions of water shortage or salinity stress. With this knowledge it will be possible to adjust existing unsaturated flow models accounting for root water uptake. We tested 8 POTs in an experimental setup, where we compared matric potential measurements to TDR water content measurements, matric potentials derived from measured water contents, and matric potentials measured by water-filled tensiometers. The experimental setup consisted of two evaporation boxes, one filled with sand (97.6% sand, 1

  3. Bi Input-extended Kalman filter based estimation technique for speed-sensorless control of induction motors

    Energy Technology Data Exchange (ETDEWEB)

    Barut, Murat, E-mail: muratbarut27@yahoo.co [Nigde University, Department of Electrical and Electronics Engineering, 51245 Nigde (Turkey)

    2010-10-15

    This study offers a novel extended Kalman filter (EKF) based estimation technique for the solution of the on-line estimation problem related to uncertainties in the stator and rotor resistances inherent to the speed-sensorless high efficiency control of induction motors (IMs) in the wide speed range as well as extending the limited number of states and parameter estimations possible with a conventional single EKF algorithm. For this aim, the introduced estimation technique in this work utilizes a single EKF algorithm with the consecutive execution of two inputs derived from the two individual extended IM models based on the stator resistance and rotor resistance estimation, differently from the other approaches in past studies, which require two separate EKF algorithms operating in a switching or braided manner; thus, it has superiority over the previous EKF schemes in this regard. The proposed EKF based estimation technique performing the on-line estimations of the stator currents, the rotor flux, the rotor angular velocity, and the load torque involving the viscous friction term together with the rotor and stator resistance is also used in the combination with the speed-sensorless direct vector control of IM and tested with simulations under the challenging 12 scenarios generated instantaneously via step and/or linear variations of the velocity reference, the load torque, the stator resistance, and the rotor resistance in the range of high and zero speed, assuming that the measured stator phase currents and voltages are available. Even under those variations, the performance of the speed-sensorless direct vector control system established on the novel EKF based estimation technique is observed to be quite good.

  4. Temperature dependence of Henry's law constant in an extended temperature range.

    Science.gov (United States)

    Görgényi, Miklós; Dewulf, Jo; Van Langenhove, Herman

    2002-08-01

    The Henry's law constants H for chloroform, 1,1-dichloroethane, 1,2-dichloropropane, trichloroethene, chlorobenzene, benzene and toluene were determined by the EPICS-SPME technique (equilibrium partitioning in closed systems--solid phase microextraction) in the temperature range 275-343 K. The curvature observed in the ln H vs. 1/T plot was due to the temperature dependence of the change in enthalpy delta H0 during the transfer of 1 mol solute from the aqueous solution to the gas phase. The nonlinearity of the plot was explained by means of a thermodynamic model which involves the temperature dependence of delta H0 of the compounds and the thermal expansion of water in the three-parameter equation ln (H rho TT) = A2/T + BTB + C2, where rho T is the density of water at temperature T, TB = ln(T/298) + (298-T)/T, A2 = -delta H298(0)/R, delta H298(0) is the delta H0 value at 298 K, B = delta Cp0/R, and C2 is a constant. delta Cp0 is the molar heat capacity change in volatilization from the aqueous solution. A statistical comparison of the two models demonstrates the superiority of the three-parameter equation over the two-parameter one ln H vs. 1/T). The new, three-parameter equation allows a more accurate description of the temperature dependence of H, and of the solubility of volatile organic compounds in water at higher temperatures.

  5. Xylella fastidiosa: Host Range and Advance in Molecular Identification Techniques

    Science.gov (United States)

    Baldi, Paolo; La Porta, Nicola

    2017-01-01

    In the never ending struggle against plant pathogenic bacteria, a major goal is the early identification and classification of infecting microorganisms. Xylella fastidiosa, a Gram-negative bacterium belonging to the family Xanthmonadaceae, is no exception as this pathogen showed a broad range of vectors and host plants, many of which may carry the pathogen for a long time without showing any symptom. Till the last years, most of the diseases caused by X. fastidiosa have been reported from North and South America, but recently a widespread infection of olive quick decline syndrome caused by this fastidious pathogen appeared in Apulia (south-eastern Italy), and several cases of X. fastidiosa infection have been reported in other European Countries. At least five different subspecies of X. fastidiosa have been reported and classified: fastidiosa, multiplex, pauca, sandyi, and tashke. A sixth subspecies (morus) has been recently proposed. Therefore, it is vital to develop fast and reliable methods that allow the pathogen detection during the very early stages of infection, in order to prevent further spreading of this dangerous bacterium. To this purpose, the classical immunological methods such as ELISA and immunofluorescence are not always sensitive enough. However, PCR-based methods exploiting specific primers for the amplification of target regions of genomic DNA have been developed and are becoming a powerful tool for the detection and identification of many species of bacteria. The aim of this review is to illustrate the application of the most commonly used PCR approaches to X. fastidiosa study, ranging from classical PCR, to several PCR-based detection methods: random amplified polymorphic DNA (RAPD), quantitative real-time PCR (qRT-PCR), nested-PCR (N-PCR), immunocapture PCR (IC-PCR), short sequence repeats (SSRs, also called VNTR), single nucleotide polymorphisms (SNPs) and multilocus sequence typing (MLST). Amplification and sequence analysis of specific

  6. Xylella fastidiosa: Host Range and Advance in Molecular Identification Techniques

    Directory of Open Access Journals (Sweden)

    Paolo Baldi

    2017-06-01

    Full Text Available In the never ending struggle against plant pathogenic bacteria, a major goal is the early identification and classification of infecting microorganisms. Xylella fastidiosa, a Gram-negative bacterium belonging to the family Xanthmonadaceae, is no exception as this pathogen showed a broad range of vectors and host plants, many of which may carry the pathogen for a long time without showing any symptom. Till the last years, most of the diseases caused by X. fastidiosa have been reported from North and South America, but recently a widespread infection of olive quick decline syndrome caused by this fastidious pathogen appeared in Apulia (south-eastern Italy, and several cases of X. fastidiosa infection have been reported in other European Countries. At least five different subspecies of X. fastidiosa have been reported and classified: fastidiosa, multiplex, pauca, sandyi, and tashke. A sixth subspecies (morus has been recently proposed. Therefore, it is vital to develop fast and reliable methods that allow the pathogen detection during the very early stages of infection, in order to prevent further spreading of this dangerous bacterium. To this purpose, the classical immunological methods such as ELISA and immunofluorescence are not always sensitive enough. However, PCR-based methods exploiting specific primers for the amplification of target regions of genomic DNA have been developed and are becoming a powerful tool for the detection and identification of many species of bacteria. The aim of this review is to illustrate the application of the most commonly used PCR approaches to X. fastidiosa study, ranging from classical PCR, to several PCR-based detection methods: random amplified polymorphic DNA (RAPD, quantitative real-time PCR (qRT-PCR, nested-PCR (N-PCR, immunocapture PCR (IC-PCR, short sequence repeats (SSRs, also called VNTR, single nucleotide polymorphisms (SNPs and multilocus sequence typing (MLST. Amplification and sequence analysis of

  7. Xylella fastidiosa: Host Range and Advance in Molecular Identification Techniques.

    Science.gov (United States)

    Baldi, Paolo; La Porta, Nicola

    2017-01-01

    In the never ending struggle against plant pathogenic bacteria, a major goal is the early identification and classification of infecting microorganisms. Xylella fastidiosa, a Gram-negative bacterium belonging to the family Xanthmonadaceae, is no exception as this pathogen showed a broad range of vectors and host plants, many of which may carry the pathogen for a long time without showing any symptom. Till the last years, most of the diseases caused by X. fastidiosa have been reported from North and South America, but recently a widespread infection of olive quick decline syndrome caused by this fastidious pathogen appeared in Apulia (south-eastern Italy), and several cases of X. fastidiosa infection have been reported in other European Countries. At least five different subspecies of X. fastidiosa have been reported and classified: fastidiosa, multiplex, pauca, sandyi, and tashke. A sixth subspecies (morus) has been recently proposed. Therefore, it is vital to develop fast and reliable methods that allow the pathogen detection during the very early stages of infection, in order to prevent further spreading of this dangerous bacterium. To this purpose, the classical immunological methods such as ELISA and immunofluorescence are not always sensitive enough. However, PCR-based methods exploiting specific primers for the amplification of target regions of genomic DNA have been developed and are becoming a powerful tool for the detection and identification of many species of bacteria. The aim of this review is to illustrate the application of the most commonly used PCR approaches to X. fastidiosa study, ranging from classical PCR, to several PCR-based detection methods: random amplified polymorphic DNA (RAPD), quantitative real-time PCR (qRT-PCR), nested-PCR (N-PCR), immunocapture PCR (IC-PCR), short sequence repeats (SSRs, also called VNTR), single nucleotide polymorphisms (SNPs) and multilocus sequence typing (MLST). Amplification and sequence analysis of specific

  8. A new PCR-based approach indicates the range of Clonorchis sinensis now extends to Central Thailand.

    Directory of Open Access Journals (Sweden)

    Rebecca J Traub

    Full Text Available Differentiation of the fish-borne trematodes belonging to the Opisthorchiidae, Heterophyidae and Lecithodendriidae is important from a clinical and epidemiological perspective, yet it is impossible to do using conventional coprological techniques, as the eggs are morphologically similar. Epidemiological investigation therefore currently relies on morphological examination of adult worms following expulsion chemotherapy. A PCR test capable of amplifying a segment of the internal transcribed spacer region of ribosomal DNA for the opisthorchiid and heterophyid flukes eggs taken directly from faeces was developed and evaluated in a rural community in central Thailand. The lowest quantity of DNA that could be amplified from individual adults of Opisthorchis viverrini, Clonorchis sinensis and Haplorchis taichui was estimated at 0.6 pg, 0.8 pg and 3 pg, respectively. The PCR was capable of detecting mixed infection with the aforementioned species of flukes under experimental conditions. A total of 11.6% of individuals in rural communities in Sanamchaikaet district, central Thailand, were positive for 'Opisthorchis-like' eggs in their faeces using conventional parasitological detection techniques. In comparison to microscopy, the PCR yielded a sensitivity and specificity of 71.0% and 76.7%, respectively. Analysis of the microscopy-positive PCR products revealed 64% and 23% of individuals to be infected with O. viverrini and C. sinensis, respectively. The remaining 13% (three individuals were identified as eggs of Didymozoidae, presumably being passed mechanically in the faeces following the ingestion of infected fishes. An immediate finding of this study is the identification and first report of a C. sinensis-endemic community in central Thailand. This extends the known range of this liver fluke in Southeast Asia. The PCR developed herein provides an important tool for the specific identification of liver and intestinal fluke species for future

  9. Extending generalized hough transform to detect 3D objects in laser range data

    NARCIS (Netherlands)

    Khoshelham, K.

    2007-01-01

    Automated detection and 3D modelling of objects in laser range data is of great importance in many applications. Existing approaches to object detection in range data are limited to either 2.5D data (e.g. range images) or simple objects with a parametric form (e.g. spheres). This paper describes a

  10. A comparative analysis of dynamic range compression techniques in IR images for maritime applications

    Science.gov (United States)

    Rossi, Alessandro; Acito, Nicola; Diani, Marco; Luison, Cristian; Olivieri, Monica; Barani, Gianni

    2013-05-01

    Modern thermal cameras acquire IR images with a high dynamic range because they have to sense with high thermal resolution the great temperature changes of monitored scenarios in specific surveillance applications. Initially developed for visible light images and recently extended for display of IR images, high dynamic range compression (HDRC) techniques aim at furnishing plain images to human operators for a first intuitive comprehension of the sensed scenario without altering the features of IR images. In this context, the maritime scenario represents a challenging case to test and develop HDRC strategies since images collected for surveillance at sea are typically characterized by high thermal gradients among the background scene and classes of objects at different temperatures. In the development of a new IRST system, Selex ES assembled a demonstrator equipped with modern thermal cameras and planned a measurement campaign on a maritime scenario so as to collect IR sequences in different operating conditions. This has led to build up a case record of situations suitable to test HDRC techniques. In this work, a survey of HDRC approaches is introduced pointing out advantages and drawbacks with focus on strategies specifically designed to display IR images. A detailed analysis of the performance is discussed in order to address the task of visualization with reference to typical issues of IR maritime images, such as robustness to the horizon effect and displaying of very warm objects and flat areas.

  11. Confidence range estimate of extended source imagery acquisition algorithms via computer simulations. [in optical communication systems

    Science.gov (United States)

    Chen, CHIEN-C.; Hui, Elliot; Okamoto, Garret

    1992-01-01

    Spatial acquisition using the sun-lit Earth as a beacon source provides several advantages over active beacon-based systems for deep-space optical communication systems. However, since the angular extend of the Earth image is large compared to the laser beam divergence, the acquisition subsystem must be capable of resolving the image to derive the proper pointing orientation. The algorithms used must be capable of deducing the receiver location given the blurring introduced by the imaging optics and the large Earth albedo fluctuation. Furthermore, because of the complexity of modelling the Earth and the tracking algorithms, an accurate estimate of the algorithm accuracy can only be made via simulation using realistic Earth images. An image simulator was constructed for this purpose, and the results of the simulation runs are reported.

  12. Investigation on the extended range of absorbing film for a microcavity enhanced graphene photodetector

    Science.gov (United States)

    Liu, Hai-Xia; Liu, Kai-Ming; Niu, Yan-Xiong

    2017-07-01

    Microcavity is the preferred graphene-based photodetector structure for its perfect feature of narrow spectral width and absorption enhancement, thus its application sheds light on ultra-fast detection in optic telecommunication and sensing fields. Due to an extremely thin film of graphene, the present study naturally deems it essential to locate the graphene in the exact position of resonant peak intensity. Here an extended graphene position margin in asymmetric planar microcavity with absorption higher than 97.35% was demonstrated. The shift of the centre wavelength caused by graphene was revealed to be non-negligible for telecommunication applications and graphene applied devices. The maximum shift beyond the designed wavelength of 1550 nm has reached 1.07 nm in the λ/2 cavity, which may have severe impact on the DWDM system. Our theoretical investigation amplifies the absorption features and the parasitical spectrum alterations of a designed photodetector with graphene.

  13. MEMS-based LC tank with extended tuning range for multiband applications

    Science.gov (United States)

    Cazzorla, A.; Farinelli, P.; Urbani, L.; Sorrentino, R.; Margesin, B.

    2016-09-01

    This paper presents the modeling, simulations, and measurements of a compact multiband microelectromechanical (MEMS)-based LC tank resonator suitable for low phase noise voltage-controlled oscillators (VCOs). The resonator is based on a high-Q spiral inductor and high capacitance ratio varicap fully integrated in FBK-irst (Fondazione Bruno Kessler) MEMS manufacturing process. The design of the varicap is based on double-actuation mechanism with a mechanical central bond that inhibits the pull-in allowing for a theoretically infinite tuning ratio. The measurements have shown a total not continuous capacitance ratio (Cr) of 5.2 with a continuous variation of the capacitance values in the range 225 fF-600 fF which corresponds to a continuous capacitance ratio (Cr*) of 2.6. The performance repeatability, the power-handling capability, and the stability over time were tested on 10 samples showing a negligible variation of the capacitance values. The spiral inductor consists of a suspended gold membrane thick 5 µm in a circular shape which was modeled in order to optimize the quality factor (Q) in the frequency range 2-4 GHz. The measurement results show a Q of about 55 in the 2-4 GHz frequency band. The LC tank measurements show an overall tuning range better than of 45% in the 3.2-4.9 GHz frequency band, consisting of two continuous tuning ranges of 7.5% and 25%. The LC tank allowed the design of MEMS-based voltage-controlled oscillators (VCOs) with an overall tuning better than 60% in the frequency range 2.15 GHz-3.85 GHz and two separate regions of continuous tuning range. The VCO prototype will be fabricated on Surface Mount Technology on RO4350 laminate. The main figures of merit are presented in comparison with the state of the art.

  14. Intelligent traffic signals : extending the range of self-organization in the BML model.

    Science.gov (United States)

    2013-04-01

    The two-dimensional traffic model of Biham, Middleton and Levine (Phys. Rev. A, 1992) is : a simple cellular automaton that exhibits a wide range of complex behavior. It consists of both : northbound and eastbound cars traveling on a rectangular arra...

  15. Gaining local accuracy while not losing generality – extending the range of gap model applications

    NARCIS (Netherlands)

    Didion, M.P.; Kupferschmid, A.D.; Zingg, A.; Fahse, L.; Bugmann, H.

    2009-01-01

    For the study of long-term processes in forests, gap models generally sacrifice accuracy (i.e., simulating system behavior in a quantitatively accurate manner) for generality (i.e., representing a broad range of systems' behaviors with the same model). We selected the gap model ForClim to evaluate

  16. An extended set-value observer for position estimation using single range measurements

    DEFF Research Database (Denmark)

    Marcal, Jose; Jouffroy, Jerome; Fossen, Thor I.

    of transponders. The knowledge of the bearing of the vehicle and the range measurements from a single location can provide a solution which is sensitive to the trajectory that the vehicle is following, since there is no complete constraint on the position estimate with a single beacon. In this paper...

  17. Polymeric pH nanosensor with extended measurement range bearing octaarginine as cell penetrating peptide

    DEFF Research Database (Denmark)

    Ke, Peng; Sun, Honghao; Liu, Mingxing

    2016-01-01

    A synthetic peptide octaarginine which mimics human immunodeficiency virus-1, Tat protein is used as cell penetrating moiety for new pH nanosensors which demonstrate enhanced cellular uptake and expanded measurement range from pH 3.9 to pH 7.3 by simultaneously incorporating two complemental p...

  18. Measured Response of Local, Mid-range and Far-range Discontinuities of Large Metal Groundplanes using Time Domain Techniques

    Directory of Open Access Journals (Sweden)

    T. Schrader

    2005-01-01

    Full Text Available This work describes a method to detect and to quantify any local or mid-range discontinuity on extended flat metal planes. Often these planes are used for antenna calibration (open area test site - OATS or the plane could be the ground of a semi-anechoic chamber used in Electromagnetic Compatibility (EMC testing. The measurement uncertainty of antenna calibration or EMC testing depends on the groundplane's quality, which can be accessed using this method. A vector network analyzer with time-domain option is used to determine the complex-valued input scattering parameter S11,F of an aperture antenna in a monostatic setup. S11,F contains the information desired about the discontinuities and is measured in the frequency domain with high dynamic range. But only after a linear filtering utilizing the Chirp-Z-Transform the obtained time-domain signal S11,T evidence of local and mid-range discontinuities.

  19. Comparison of extended medium-range forecast skill between KMA ensemble, ocean coupled ensemble, and GloSea5

    Science.gov (United States)

    Park, Sangwook; Kim, Dong-Joon; Lee, Seung-Woo; Lee, Kie-Woung; Kim, Jongkhun; Song, Eun-Ji; Seo, Kyong-Hwan

    2017-08-01

    This article describes a three way inter-comparison of forecast skill on an extended medium-range time scale using the Korea Meteorological Administration (KMA) operational ensemble numerical weather prediction (NWP) systems (i.e., atmosphere-only global ensemble prediction system (EPSG) and ocean-atmosphere coupledEPSG) and KMA operational seasonal prediction system, the Global Seasonal forecast system version 5 (GloSea5). The main motivation is to investigate whether the ensemble NWP system can provide advantage over the existing seasonal prediction system for the extended medium-range forecast (30 days) even with putting extra resources in extended integration or coupling with ocean with NWP system. Two types of evaluation statistics are examined: the basic verification statistics - the anomaly correlation and RMSE of 500-hPa geopotential height and 1.5-meter surface temperature for the global and East Asia area, and the other is the Real-time Multivariate Madden and Julian Oscillation (MJO) indices (RMM1 and RMM2) - which is used to examine the MJO prediction skill. The MJO is regarded as a main source of forecast skill in the tropics linked to the mid-latitude weather on monthly time scale. Under limited number of experiment cases, the coupled NWP extends the forecast skill of the NWP by a few more days, and thereafter such forecast skill is overtaken by that of the seasonal prediction system. At present stage, it seems there is little gain from the coupled NWP even though more resources are put into it. Considering this, the best combination of numerical product guidance for operational forecasters for an extended medium-range is extension of the forecast lead time of the current ensemble NWP (EPSG) up to 20 days and use of the seasonal prediction system (GloSea5) forecast thereafter, though there exists a matter of consistency between the two systems.

  20. Improving the Dynamic Emissivity Measurement Above 1000 K by Extending the Spectral Range

    Science.gov (United States)

    Urban, D.; Krenek, S.; Anhalt, K.; Taubert, D. R.

    2018-01-01

    To improve the dynamic emissivity measurement, which is based on the laser-flash method, an array spectrometer is characterized regarding its spectral radiance responsivity for a spectrally resolved emissivity measurement above 1000 K in the wavelength range between 550 nm and 1100 nm. Influences like dark signals, the nonlinearity of the detector, the size-of-source effect, wavelength calibration and the spectral radiance responsivity of the system are investigated to obtain an uncertainty budget for the spectral radiance and emissivity measurements. Uncertainties for the spectral radiance of lower than a relative 2 % are achieved for wavelengths longer than 550 nm. Finally, the spectral emissivity of a graphite sample was determined in the temperature range between 1000 K and 1700 K, and the experimental data show a good repeatability and agreement with literature data.

  1. DEM GENERATION FROM CLOSE-RANGE PHOTOGRAMMETRY USING EXTENDED PYTHON PHOTOGRAMMETRY TOOLBOX

    OpenAIRE

    A. A. Belmonte; M. M. P. Biong; Macatulad, E. G.

    2017-01-01

    Digital elevation models (DEMs) are widely used raster data for different applications concerning terrain, such as for flood modelling, viewshed analysis, mining, land development, engineering design projects, to name a few. DEMs can be obtained through various methods, including topographic survey, LiDAR or photogrammetry, and internet sources. Terrestrial close-range photogrammetry is one of the alternative methods to produce DEMs through the processing of images using photogrammetry softwa...

  2. Extended calibration range for prompt photon emission in ion beam irradiation

    OpenAIRE

    Bellini, F.; Boehlen, T.T.; Chin, M P W; Collamati, F; De Lucia, E.; Faccini, R.; Ferrari, A.; Lanza, L.; Mancini-Terraciano, C.; Marafini, M.; Mattei, I.; Morganti, S; Ortega, P.G.; V. Patera; Piersanti, L.

    2013-01-01

    Monitoring the dose delivered during proton and carbon ion therapy is still a matter of research. Among the possible solutions, several exploit the measurement of the single photon emission from nuclear decays induced by the irradiation. To fully characterize such emission the detectors need development, since the energy spectrum spans the range above the MeV that is not traditionally used in medical applications. On the other hand, a deeper understanding of the reactions involving gamma prod...

  3. Field System for Extended Range Continuous Monitoring of Near Surface CO2 Gas from Multiple Locations

    Science.gov (United States)

    Barr, J.; Amonette, J.

    2007-12-01

    A novel system was developed for continuous measurement of near surface carbon dioxide gas concentrations associated with the monitoring of carbon dioxide capture and storage in geologic formations. In the current configuration, the battery powered system allows for near surface CO2 gas collection (0-300,000 ppm) from seven (expandable) independently located steady state chambers. Each chamber has an associated pump and metering valve attached to a control manifold that either directs the flow to the analyzer (test chamber) or to exhaust (all others). The uniquely large concentration range in which the system is capable of operating is achieved by using an auto-control system that senses when the LiCor LI-7000 analyzer is approaching saturation and then dilutes the incoming sample using a metered flow of nitrogen gas from the reference gas supply. The dilution is carried out in stages and is capable of increasing or decreasing on the fly to keep the analyzer within range. By reading in the sample flow rate, the dilution gas flow rate, and the output flow it is possible to calculate a dilution scalar that acts as a multiplier for the LiCor analyzer concentration, allowing for immediate read and record of true sampler concentrations. This system was tested and validated during a week of continuous operation and field use, monitoring the seven chambers 24 hours/day with CO2 concentrations ranging from background to over 130,000 ppm.

  4. An extended range generic immunoassay for total human therapeutic antibodies in preclinical pharmacokinetic studies.

    Science.gov (United States)

    Hall, Colin M; Pearson, Josh T; Patel, Vimal; Wienkers, Larry C; Greene, Robert J

    2013-07-31

    Bioanalytical support of discovery programs for human monoclonal antibody therapies involves quantitation by immunoassay. Historically, preclinical samples have been analyzed by the traditional Enzyme-Linked Immuno-Sorbent Assay (ELISA). We investigated transferring our generic ELISA for quantitating human IgG constructs in preclinical serum samples to an automated microfluidics immunoassay platform based on nanoscale streptavidin bead columns. Transfer of our immunoassay to the automated platform resulted in not only the anticipated reduction in analysts' time required for manual manipulation (ELISA) but also a substantial increase in the dynamic range of the immunoassay. The generic nature and wide dynamic range of this automated microcolumn immunoassay permit bioanalytical support of novel therapeutic candidates without the need to develop new, specific assay reagents and minimize the chances that sample reassays will be required due to out of range concentration results. Improved process efficiencies and enhanced workflow during the analysis of preclinical PK samples that enable high throughput assessment of a human monoclonal antibody lead in early discovery programs. Copyright © 2013 Elsevier B.V. All rights reserved.

  5. Research Investigation Directed Toward Extending the Useful Range of the Electromagnetic Spectrum.

    Science.gov (United States)

    1981-03-31

    in the semiconductor at a distance x from the surface, E is the dielectric constant of the semiconductor, and (x) = q(nno - Pno + Pn - n ) (4) is the... acid (HF). The samples were dried in N2 gas, and oxidized in dry 02 at 12000C in the presence of hydrogen chloride (HCl). High-tempera- 22ture (1200°C...hydrogen containing molecules. We are currently studying the vibrational relaxation of SO 2over the temperature range 210 K to 500 K. Sulphur dioxide has

  6. Research Investigation Directed Toward Extending the Useful Range of the Electromagnetic Spectrum.

    Science.gov (United States)

    1985-12-31

    1818 (1975). (14) D.R. Hardin, K.B. Woodall and R~. Grice , Mol. Phys. 26, 1057 (1973). (15) W.S. Struve, T. Kitigawa and D.R. Herschbach, J. Chem...cross sections until the maxima are reached. Because 4Tra n is 0the quantum mechanical result for a hard-sphere collisional cross section, the...intermediate n range, Li cross sections reach their maximum values slightly lower than Na by a difference of 1 to 3 in n; Li’s maxima are - . smaller

  7. Establishing a link to given radiated emission limits during extending the frequency range above 1 GHz

    Directory of Open Access Journals (Sweden)

    H. Garbe

    2008-05-01

    Full Text Available Up to now most limits for radiated emission are given as values for the electrical field strength. Battermann, 2007 has shown that the frequency range extension for radiated emission measurements above 1 GHz generates a lot of problems while performing the test on a classical test site as depicted in Fig. 1. This paper will give a motivation to use an other measurand namely the total-radiated-power than electrical field strength by using alternative test sites like reverberation chambers, TEM-waveguides, Fully Anechoic Rooms (FAR etc. Nevertheless most of the existing standards still specify electrical field strength limits. This paper will show how to set the parameters in the given algorithm to establish a link between measured total radiated power and equivalent electrical field values.

  8. Paralleling power MOSFETs in their active region: Extended range of passively forced current sharing

    Science.gov (United States)

    Niedra, Janis M.

    1989-01-01

    A simple passive circuit that improves current balance in parallelled power MOSFETs that are not precisely matched and that are operated in their active region from a common gate drive are exhibited. A nonlinear circuit consisting of diodes and resistors generates the differential gate potential required to correct for unbalance while maintaining low losses over a range of current. Also application of a thin tape wound magnetic core to effect dynamic current balance is reviewed, and a simple theory is presented showing that for operation in the active region the branch currents tend to revert to their normal unbalanced values even if the core is not driven into saturation. Results of several comparative experiments are given.

  9. Designing an extended energy range single-sphere multi-detector neutron spectrometer

    Energy Technology Data Exchange (ETDEWEB)

    Gomez-Ros, J.M., E-mail: jm.gomezros@ciemat.es [CIEMAT, Av. Complutense 40, 28040 Madrid (Spain); IFNF-LNF, U.F. Fisica Sanitaria, via E. Fermi n. 40, 00044 Frascati (Italy); Bedogni, R. [IFNF-LNF, U.F. Fisica Sanitaria, via E. Fermi n. 40, 00044 Frascati (Italy); Moraleda, M. [CIEMAT, Av. Complutense 40, 28040 Madrid (Spain); Esposito, A. [IFNF-LNF, U.F. Fisica Sanitaria, via E. Fermi n. 40, 00044 Frascati (Italy); Pola, A.; Introini, M.V. [Politecnico di Milano, Dipartimento di Energia, via Ponzio 34/3, 20133 Milano (Italy); Mazzitelli, G.; Quintieri, L.; Buonomo, B. [IFNF-LNF, U.F. Fisica Sanitaria, via E. Fermi n. 40, 00044 Frascati (Italy)

    2012-06-11

    This communication describes the design specifications for a neutron spectrometer consisting of 31 thermal neutron detectors, namely Dysprosium activation foils, embedded in a 25 cm diameter polyethylene sphere which includes a 1 cm thick lead shell insert that degrades the energy of neutrons through (n,xn) reactions, thus allowing to extension of the energy range of the response up to hundreds of MeV neutrons. The new spectrometer, called SP{sup 2} (SPherical SPectrometer), relies on the same detection mechanism as that of the Bonner Sphere Spectrometer, but with the advantage of determining the whole neutron spectrum in a single exposure. The Monte Carlo transport code MCNPX was used to design the spectrometer in terms of sphere diameter, number and position of the detectors, position and thickness of the lead shell, as well as to obtain the response matrix for the final configuration. This work focuses on evaluating the spectrometric capabilities of the SP{sup 2} design by simulating the exposure of SP{sup 2} in neutron fields representing different irradiation conditions (test spectra). The simulated SP{sup 2} readings were then unfolded with the FRUIT unfolding code, in the absence of detailed pre-information, and the unfolded spectra were compared with the known test spectra. The results are satisfactory and allowed approving the production of a prototypal spectrometer.

  10. Studying biological membranes with extended range high-speed atomic force microscopy

    Science.gov (United States)

    Nievergelt, Adrian P.; Erickson, Blake W.; Hosseini, Nahid; Adams, Jonathan D.; Fantner, Georg E.

    2015-01-01

    High—speed atomic force microscopy has proven to be a valuable tool for the study of biomolecular systems at the nanoscale. Expanding its application to larger biological specimens such as membranes or cells has, however, proven difficult, often requiring fundamental changes in the AFM instrument. Here we show a way to utilize conventional AFM instrumentation with minor alterations to perform high-speed AFM imaging with a large scan range. Using a two—actuator design with adapted control systems, a 130 × 130 × 5 μm scanner with nearly 100 kHz open—loop small-signal Z—bandwidth is implemented. This allows for high-speed imaging of biologically relevant samples as well as high-speed measurements of nanomechanical surface properties. We demonstrate the system performance by real-time imaging of the effect of charged polymer nanoparticles on the integrity of lipid membranes at high imaging speeds and peak force tapping measurements at 32 kHz peak force rate. PMID:26169348

  11. Studying biological membranes with extended range high-speed atomic force microscopy.

    Science.gov (United States)

    Nievergelt, Adrian P; Erickson, Blake W; Hosseini, Nahid; Adams, Jonathan D; Fantner, Georg E

    2015-07-14

    High-speed atomic force microscopy has proven to be a valuable tool for the study of biomolecular systems at the nanoscale. Expanding its application to larger biological specimens such as membranes or cells has, however, proven difficult, often requiring fundamental changes in the AFM instrument. Here we show a way to utilize conventional AFM instrumentation with minor alterations to perform high-speed AFM imaging with a large scan range. Using a two-actuator design with adapted control systems, a 130 × 130 × 5 μm scanner with nearly 100 kHz open-loop small-signal Z-bandwidth is implemented. This allows for high-speed imaging of biologically relevant samples as well as high-speed measurements of nanomechanical surface properties. We demonstrate the system performance by real-time imaging of the effect of charged polymer nanoparticles on the integrity of lipid membranes at high imaging speeds and peak force tapping measurements at 32 kHz peak force rate.

  12. Studying biological membranes with extended range high-speed atomic force microscopy

    Science.gov (United States)

    Nievergelt, Adrian P.; Erickson, Blake W.; Hosseini, Nahid; Adams, Jonathan D.; Fantner, Georg E.

    2015-07-01

    High—speed atomic force microscopy has proven to be a valuable tool for the study of biomolecular systems at the nanoscale. Expanding its application to larger biological specimens such as membranes or cells has, however, proven difficult, often requiring fundamental changes in the AFM instrument. Here we show a way to utilize conventional AFM instrumentation with minor alterations to perform high-speed AFM imaging with a large scan range. Using a two—actuator design with adapted control systems, a 130 × 130 × 5 μm scanner with nearly 100 kHz open—loop small-signal Z—bandwidth is implemented. This allows for high-speed imaging of biologically relevant samples as well as high-speed measurements of nanomechanical surface properties. We demonstrate the system performance by real-time imaging of the effect of charged polymer nanoparticles on the integrity of lipid membranes at high imaging speeds and peak force tapping measurements at 32 kHz peak force rate.

  13. Extended Constant Power Speed Range of the Brushless DC Motor Through Dual Mode Inverter Control

    Energy Technology Data Exchange (ETDEWEB)

    Lawler, J.S.

    2000-06-23

    The trapezoidal back electromotive force (emf) brushless direct current (dc) motor (BDCM) with surface-mounted magnets has high-power density and efficiency especially when rare-earth magnet materials are used. Traction applications, such as electric vehicles, could benefit significantly from the use of such motors. Unfortunately, a practical means for driving the motor over a constant power speed ratio (CPSR) of 5:1 or more has not yet been developed. A key feature of these motors is that they have low internal inductance. The phase advance method is effective in controlling the motor power over such a speed range, but the current at high speed may be several times greater than that required at the base speed. The increase in current during high-speed operation is due to the low motor inductance and the action of the bypass diodes of the inverter. The use of such a control would require increased current rating of the inverter semiconductors and additional cooling for the inverter, where the conduction losses increase proportionally with current, and especially for the motor, where the losses increase with the square of the current. The high current problems of phase advance can be mitigated by adding series inductance; however, this reduces power density, requires significant increase in supply voltage, and leaves the CPSR performance of the system highly sensitive to variations in the available voltage. A new inverter topology and control scheme has been developed that can drive low-inductance BDCMs over the CPSR that would be required in electric vehicle applications. This new controller is called the dual-mode inverter control (DMIC). It is shown that the BDCM has an infinite CPSR when it is driven by the DMIC.

  14. Error sensitivity analysis in 10-30-day extended range forecasting by using a nonlinear cross-prediction error model

    Science.gov (United States)

    Xia, Zhiye; Xu, Lisheng; Chen, Hongbin; Wang, Yongqian; Liu, Jinbao; Feng, Wenlan

    2017-06-01

    Extended range forecasting of 10-30 days, which lies between medium-term and climate prediction in terms of timescale, plays a significant role in decision-making processes for the prevention and mitigation of disastrous meteorological events. The sensitivity of initial error, model parameter error, and random error in a nonlinear crossprediction error (NCPE) model, and their stability in the prediction validity period in 10-30-day extended range forecasting, are analyzed quantitatively. The associated sensitivity of precipitable water, temperature, and geopotential height during cases of heavy rain and hurricane is also discussed. The results are summarized as follows. First, the initial error and random error interact. When the ratio of random error to initial error is small (10-6-10-2), minor variation in random error cannot significantly change the dynamic features of a chaotic system, and therefore random error has minimal effect on the prediction. When the ratio is in the range of 10-1-2 (i.e., random error dominates), attention should be paid to the random error instead of only the initial error. When the ratio is around 10-2-10-1, both influences must be considered. Their mutual effects may bring considerable uncertainty to extended range forecasting, and de-noising is therefore necessary. Second, in terms of model parameter error, the embedding dimension m should be determined by the factual nonlinear time series. The dynamic features of a chaotic system cannot be depicted because of the incomplete structure of the attractor when m is small. When m is large, prediction indicators can vanish because of the scarcity of phase points in phase space. A method for overcoming the cut-off effect ( m > 4) is proposed. Third, for heavy rains, precipitable water is more sensitive to the prediction validity period than temperature or geopotential height; however, for hurricanes, geopotential height is most sensitive, followed by precipitable water.

  15. Early Results of Chimney Technique for Type B Aortic Dissections Extending to the Aortic Arch

    Energy Technology Data Exchange (ETDEWEB)

    Huang, Chen [Affiliated Hospital of Nantong University, Department of General Surgery (China); Tang, Hanfei; Qiao, Tong; Liu, Changjian; Zhou, Min, E-mail: 813477618@qq.com [The Affiliated Hospital of Nanjing University Medical School, Department of Vascular Surgery, Nanjing Drum Tower Hospital (China)

    2016-01-15

    ObjectiveTo summarize our early experience gained from the chimney technique for type B aortic dissection (TBAD) extending to the aortic arch and to evaluate the aortic remodeling in the follow-up period.MethodsFrom September 2011 to July 2014, 27 consecutive TBAD patients without adequate proximal landing zones were retrograde analyzed. Chimney stent-grafts were deployed parallel to the main endografts to reserve flow to branch vessels while extending the landing zones. In the follow-up period, aortic remodeling was observed with computed tomography angiography.ResultsThe technical success rate was 100 %, and endografts were deployed in zone 0 (n = 3, 11.1 %), zone 1 (n = 18, 66.7 %), and zone 2 (n = 6, 22.2 %). Immediately, proximal endoleaks were detected in 5 patients (18.5 %). During a mean follow-up period of 17.6 months, computed tomography angiography showed all the aortic stent-grafts and chimney grafts to be patent. Favorable remodeling was observed at the level of maximum descending aorta and left subclavian artery with expansion of true lumen (from 18.4 ± 4.8 to 25 ± 0.86 mm, p < 0.001 and 27.1 ± 0.62 to 28.5 ± 0.37 mm, p < 0.001) and depressurization of false lumen (from 23.7 ± 2.7 to 8.7 ± 3.8 mm, p < 0.001, from 5.3 ± 1.2 to 2.1 ± 2.1 mm, p < 0.001). While at the level of maximum abdominal aorta, suboptimal remodeling of the total aorta (from 24.1 ± 0.4 to 23.6 ± 1.5 mm, p = 0.06) and true lumen (from 13.8 ± 0.6 to 14.5 ± 0.4 mm, p = 0.08) was observed.ConclusionBased on our limited experience, the chimney technique with thoracic endovascular repair is demonstrated to be promising for TBAD extending to the arch with favorable aortic remodeling.

  16. The statistical extended-range (10-30-day) forecast of summer rainfall anomalies over the entire China

    Science.gov (United States)

    Zhu, Zhiwei; Li, Tim

    2017-01-01

    The extended-range (10-30-day) rainfall forecast over the entire China was carried out using spatial-temporal projection models (STPMs). Using a rotated empirical orthogonal function analysis of intraseasonal (10-80-day) rainfall anomalies, China is divided into ten sub-regions. Different predictability sources were selected for each of the ten regions. The forecast skills are ranked for each region. Based on temporal correlation coefficient (TCC) and Gerrity skill score, useful skills are found for most parts of China at a 20-25-day lead. The southern China and the mid-lower reaches of Yangtze River Valley show the highest predictive skills, whereas southwestern China and Huang-Huai region have the lowest predictive skills. By combining forecast results from ten regional STPMs, the TCC distribution of 8-year (2003-2010) independent forecast for the entire China is investigated. The combined forecast results from ten STPMs show significantly higher skills than the forecast with just one single STPM for the entire China. Independent forecast examples of summer rainfall anomalies around the period of Beijing Olympic Games in 2008 and Shanghai World Expo in 2010 are presented. The result shows that the current model is able to reproduce the gross pattern of the summer intraseasonal rainfall over China at a 20-day lead. The present study provides, for the first time, a guide on the statistical extended-range forecast of summer rainfall anomalies for the entire China. It is anticipated that the ideas and methods proposed here will facilitate the extended-range forecast in China.

  17. Extended-range forecast for the temporal distribution of clustering tropical cyclogenesis over the western North Pacific

    Science.gov (United States)

    Zhu, Zhiwei; Li, Tim; Bai, Long; Gao, Jianyun

    2017-11-01

    Based on outgoing longwave radiation (OLR), an index for clustering tropical cyclogenesis (CTC) over the western North Pacific (WNP) was defined. Around 76 % of total CTC events were generated during the active phase of the CTC index, and 38 % of the total active phase was concurrent with CTC events. For its continuous property, the CTC index was used as the representative predictand for extended-range forecasting the temporal distribution of CTC events. The predictability sources for CTC events were detected via correlation analyses of the previous 35-5-day lead atmospheric fields against the CTC index. The results showed that the geopotential height at different levels and the 200 hPa zonal wind over the global tropics possessed large predictability sources, whereas the predictability sources of other variables, e.g., OLR, zonal wind, and relatively vorticity at 850 hPa and relatively humility at 700 hPa, were mainly confined to the tropical Indian Ocean and western Pacific Ocean. Several spatial-temporal projection model (STPM) sets were constructed to carry out the extended-range forecast for the CTC index. By combining the output of STPMs separately conducted for the two dominant modes of intraseasonal variability, e.g., the 10-30 and the 30-80 day mode, useful forecast skill could be achieved for a 30-day lead time. The combined output successfully captured both the 10-30 and 30-80 day mode at least 10 days in advance. With a relatively low rate of false alarm, the STPM achieved hits for 80 % (69 %) of 54 CTC events during 2003-2014 at the 10-day (20-day) lead time, suggesting a practical value of the STPM for real-time forecasting WNP CTC events at an extended range.

  18. Construction of an extended range whole-cell tetracycline biosensor by use of the tet(M) resistance gene

    DEFF Research Database (Denmark)

    Bahl, Martin Iain; Hansen, Lars Hestbjerg; Sørensen, Søren Johannes

    2005-01-01

    protein gene. Tetracycline, oxytetracycline, chlortetracycline and minocycline all effectively induced the resulting Escherichia coli MC4100/pTGM biosensor and similar dose-response characteristics were recorded by flow cytometry for all four compounds. The novel tetracycline biosensor was responsive......An extended range whole-cell tetracycline biosensor strain was constructed by insertion of the tet(M) gene, encoding tetracycline resistance by ribosomal protection, into plasmid pTGFP2, which contains a transcriptional fusion between a tetracycline regulated promoter and the green fluorescent...

  19. Rescue of an extending capsulorrhexis by creating a midway tangential anterior capsular flap: a novel technique in 22 eyes.

    Science.gov (United States)

    Mohammadpour, Mehrdad

    2010-06-01

    To show how an extending capsulorrhexis can be rescued by a midway tangential capsular flap in order to achieve an uneventful phacoemulsification. Consecutive case series. Twenty-two eyes of 22 patients with extending capsulorrhexis treated at the Farabi Eye Hospital, Tehran. First, a tangential capsular opening was created on the border of the presumed continuous curvilinear capsulorrhexis just midway between the beginning of the capsulorrhexis and the edge of the extending capsulorrhexis, to make a tangential flap of the anterior capsule. Second, the centre of this new flap was grasped and pulled centripetally until the edges of the new flap joined the edges of the extending flap to complete the capsulorrhexis. The technique was successfully performed in all cases, leading to an uneventful phacoemulsification. Midway tangential capsular flap is a safe and effective technique to rescue an extending capsulorrhexis and leads to an uneventful phacoemulsification.

  20. Extended Range Intercept Technology

    Science.gov (United States)

    1991-09-01

    grayish white hyssop Agastache cana Sensitive gypsum blazing star Mentzelia perenis Sensitive gypsum wort Pseudoclappia arenaria Sensitive La Jolla...summa Eustoma exaltatus Chrysothamnus pulchellus elatior Aletes filifolius Tetradymia filifolia Agastache verticillata Opuntia wootonil Zephranthes

  1. Extending the Linear Modulation Range to the Full Base Speed Using a Single DC-Link Multilevel Inverter With Capacitor-Fed H-Bridges for IM Drives

    DEFF Research Database (Denmark)

    Rahul, Arun; Pramanick, Sumit; Kaarthik, R. Sudharshan

    2017-01-01

    In this paper, a new space vector pulse width modulation method to extend the linear modulation range of a cascaded five level inverter topology with a single dc supply is presented. Using this method, the inverter can be controlled linearly and the peak phase fundamental output voltage...... of the inverter can be increased from 0.577 to 0.637Vdc without increasing the dc bus voltage and without exceeding the induction motor voltage rating. This new technique makes use of cascaded inverter pole voltage redundancy and property of the space vector structure for its operation. Using this, the induction...... motor drive can be operated till the full speed range (0-50 Hz) with the elimination of lower order harmonics in the phase voltage and phase current. The five-level topology presented in this paper is realized by cascading a two-level inverter and two full bridge modules with floating capacitors...

  2. Successful Restoration of Visual Acuity with an Extended Range of Vision Intraocular Lens after Multifocal Laser Ablation

    Directory of Open Access Journals (Sweden)

    Sondra Black

    2016-10-01

    Full Text Available As our baby boomer population is aging and developing cataracts, so are our post-LASIK patients. These patients underwent LASIK surgery as they wished to be spectacle-free and are hoping to remain so after intraocular lens (IOL surgery. Unfortunately, very little information is available regarding the suitability of presbyopia correcting IOLs for post-LASIK patients. This case represents successful implantation of an extended range of vision IOL in a 59-year-old patient who underwent multifocal ablation excimer laser surgery 12 years before. Emmetropia was targeted for the dominant eye and –0.5 D for the fellow eye. The 13 month follow-up after bilateral implantation of the TECNIS Symfony IOL revealed an uncorrected visual acuity of 20/25 for distance, 20/20 for intermediate and 20/16 for near. The patient is very happy and did not report any visual symptoms when asked. This successful case should encourage surgeons to consider implanting an extended range of vision IOLs in post-LASIK patients.

  3. Robot-Assisted Extended Pelvic Lymph Nodes Dissection for Prostate Cancer: Personal Surgical Technique and Outcomes

    Directory of Open Access Journals (Sweden)

    Porpiglia Francesco

    2015-12-01

    Full Text Available Objective: Extended pelvic lymph nodes dissection (EPLND allows the removal of a higher number of lymph nodes than limited PLND. The aims of this study were to describe our robot-assisted EPLND (RAEPLND technique with related complications, and to report the number of lymph nodes removed and the rate of lymph nodal metastasis. Materials and Methods: 153 patients underwent RAEPLND prior to robot-assisted radical prostatectomy (RARP. Indications were defined according to Briganti nomogram, to predict risk of lymph-nodal metastasis. Lymphatic packages covering the distal tract of the common iliac artery, the medial portion of the external iliac artery, the external iliac vein and the internal iliac vessels, together with the obturator and the presacral lymphatic packages were removed on both sides. Results: Median preoperative PSA was 7.5 ng/mL (IQR 5.5–11.5. Median operative time was 150 min (135–170. Median RAEPLND alone operative time was 38 min (32.75–41.25; for right and left side, 18 (15–29 and 20 min (15.75–30 (p=0.567. Median number of lymph nodes retrieved per patient was 25 (19.25–30; 13 (11–16 and 11 (8–15 for right and left side. In 19 patients (12.41% metastasis was found at the level of pelvic lymph nodes. Median number of positive lymph nodes was 1 (1–4.6 per patient. Complications occurred in 11 patients (7.3%. Conclusions: the number of lymph nodes removed was comparable to published data about open series, allowing the increase of detection rate of lymph nodal metastasis for minimally invasive approach without compromising complications' rate if performing the procedure following reported technique.

  4. Robot-Assisted Extended Pelvic Lymph Nodes Dissection for Prostate Cancer: Personal Surgical Technique and Outcomes.

    Science.gov (United States)

    Porpiglia, Francesco; De Luca, Stefano; Bertolo, Riccardo; Passera, Roberto; Mele, Fabrizio; Manfredi, Matteo; Amparore, Daniele; Morra, Ivano; Fiori, Cristian

    2015-01-01

    Extended pelvic lymph nodes dissection (EPLND) allows the removal of a higher number of lymph nodes than limited PLND. The aims of this study were to describe our robot-assisted EPLND (RAEPLND) technique with related complications, and to report the number of lymph nodes removed and the rate of lymph nodal metastasis. 153 patients underwent RAEPLND prior to robot-assisted radical prostatectomy (RARP). Indications were defined according to Briganti nomogram, to predict risk of lymph-nodal metastasis. Lymphatic packages covering the distal tract of the common iliac artery, the medial portion of the external iliac artery, the external iliac vein and the internal iliac vessels, together with the obturator and the presacral lymphatic packages were removed on both sides. Median preoperative PSA was 7.5 ng/mL (IQR 5.5-11.5). Median operative time was 150 min (135-170). Median RAEPLND alone operative time was 38 min (32.75-41.25); for right and left side, 18 (15-29) and 20 min (15.75-30) (p=0.567). Median number of lymph nodes retrieved per patient was 25 (19.25-30); 13 (11-16) and 11 (8-15) for right and left side. In 19 patients (12.41%) metastasis was found at the level of pelvic lymph nodes. Median number of positive lymph nodes was 1 (1-4.6) per patient. Complications occurred in 11 patients (7.3%). the number of lymph nodes removed was comparable to published data about open series, allowing the increase of detection rate of lymph nodal metastasis for minimally invasive approach without compromising complications' rate if performing the procedure following reported technique.

  5. A New Technique to Compute Long-Range Wakefields in Accelerating Structures

    CERN Document Server

    Raguin, J Y; Wuensch, Walter

    2002-01-01

    A new technique is proposed to compute the coupling impedances and the long-range wakefields based on a scattering-matrix formalism which relies heavily upon post-processed data from the commercial finite-element code HFSS. To illustrate the speed of this technique, the procedures to compute the long-range wakefields of conventional constant-impedance structures and of structures damped with waveguides are presented. The efficiency and accuracy of the technique is achieved because the characteristics of periodic structures can be computed using single-cell data. Damping and synchronism effects are determined from such a computation.

  6. Validity of Inter-rectus Distance Measurement in Postpartum Women Using Extended Field-of-View Ultrasound Imaging Techniques.

    Science.gov (United States)

    Keshwani, Nadia; Mathur, Sunita; McLean, Linda

    2015-10-01

    Reliability and validity study. To investigate the criterion-related validity and reliability of inter-rectus distance (IRD) measurement using extended field-of-view (FOV) techniques during ultrasound imaging (USI) in parous women. Ultrasound imaging is the gold standard for noninvasive IRD measurement in parous women when investigating diastasis recti; however, its use is limited when IRD is large. Extended FOV techniques (panoramic USI or using acoustic standoff pads) allow complete visualization of the linea alba when the IRD is large and conventional imaging is not sufficient; however, the validity of using these techniques has never been investigated. Two-dimensional ultrasound images were acquired at the superior umbilical border from 21 women using conventional USI, panoramic USI, and a standoff pad. Five images were captured using each method. Inter-rectus distance was measured offline. Criterion-related validity was investigated using repeated-measures analyses of variance to test for bias, and linear regression models, Pearson correlation coefficients (r), and intraclass correlation coefficients (ICCs) to assess agreement. Standard error of the measurement for each extended FOV technique was calculated. The between-trial reliability of each technique was determined using ICCs. Inter-rectus distance from images acquired using extended FOV techniques did not differ from values acquired using conventional USI (P = .441). Images acquired using extended FOV techniques were highly correlated with those acquired using conventional imaging (r>0.95, Ptechnique was 0.17 to 0.18 cm. The between-trial reliability of all techniques was excellent (ICC(3,1)>0.90). Panoramic USI and acoustic standoff pads are valid methods of increasing FOV to measure IRD. In this study, USI measurements were limited to IRDs of less than or equal to 3 finger widths, based on palpation.

  7. Latissimus dorsi mini-flap: a technique for extending breast conservation.

    Science.gov (United States)

    Dixon, J M; Venizelos, B; Chan, P

    2002-02-01

    The latissimus dorsi (LD) flap was first used in patients for breast reconstruction in 1896. More recently it has been used to fill defects after quadrantectomy or very wide excision. We have developed a two stage procedure for excision of large breast cancers which would otherwise require mastectomy. The first stage is a wide excision of the cancer without removal of the overlying skin. Thirty patients with large localized operable breast cancer underwent wide local excision followed 5 to 10 days later in 25 patients who had clear histological margins by an axillary dissection with transfer of the LD muscle and overlying fat into the defect in the breast (mini-flap). The cosmetic outcome of these 25 patients who underwent mini-flap were compared with age matched patients having a standard wide local excision and axillary node clearance or mastectomy and immediate breast reconstruction. The volume of tissue excised in patients having their defects filled by LD mini-flap was significantly greater than those women undergoing standard wide excision, pself consciousness and less change in attitude of their spouse, p=0.03 and they were more likely to choose the same operation in future compared with patients having immediate whole breast reconstruction, p=0.02. Results as rated by patients in the mini-flap group were similar to those women treated by standard wide local excision. Only one patient in the mini-flap group felt sexually inhibited. When wide local excision and LD mini-flap is performed as a two stage procedure, it is an oncologically safe technique and extends breast conservation to women with larger tumours. The cosmetic outcomes appear better than those following the alternative of mastectomy and immediate breast reconstruction.

  8. Extending the frequency range of free-field reciprocity calibration of measurement microphones to frequencies up to 150 kHz

    DEFF Research Database (Denmark)

    Barrera Figueroa, Salvador; Torras Rosell, Antoni; Jacobsen, Finn

    2013-01-01

    Measurement microphones are typically calibrated in a free field at frequencies up to 50 kHz. This is a sufficiently high frequency for the most sound measurement applications related with noise assessment. However, other applications such as the measurement of noise emitted by ultrasound cleaning...... machines and failure detection in aeronautic structures require that the sensitivity of the microphone is known at frequencies up to 150 kHz. Another area of particular interest is the investigation of the perception mechanisms of ultrasound. In any of these applications, it is of fundamental importance...... to establish a well-defined traceability chain to support the measurement results. In order to extend the frequency range of free-field calibration the measurement system and measurement methods must undergo a series of changes and adaptations including the type of excitation signal, techniques for eliminating...

  9. An Efficiency-Optimized Isolated Bidirectional DC-DC Converter with Extended Power Range for Energy Storage Systems in Microgrids

    Directory of Open Access Journals (Sweden)

    Xiaolong Shi

    2012-12-01

    Full Text Available This paper proposes a novel extended-single-phase shift (ESPS control strategy of isolated bidirectional full-bridge DC-DC converters (IBDCs which are a promising alternative as a power electronic interface in microgrids with an additional function of galvanic isolation. Based on the mathematical models of ESPS control under steady-state conditions, detailed theoretical and experimental analyses of IBDC under ESPS control are presented. Compared with conventional single-phase-shift (CSPS control, ESPS control can greatly improve the efficiency of IBDCs in microgrids through decreasing current stress and backflow power considerably over a wide input and output voltage range under light and medium loads. In addition, ESPS control only needs to adjust one single phase-shift angel to control transmission power, thus it retains implementation simplicity in comparison with dual-phase-shift (DPS control for microgrid applications. Furthermore, an efficiency-optimized modulation scheme based on ESPS and CSPS control is developed in the whole power range of IBDC for power distribution in microgrids. A 10 kW IBDC prototype is constructed and the experimental results validate the effectiveness of the proposed control strategy, showing that the proposed strategy can enhance the overall efficiency up to 30%.

  10. A New Control Method for a Bi-Directional Phase-Shift-Controlled DC-DC Converter with an Extended Load Range

    Directory of Open Access Journals (Sweden)

    Wenzheng Xu

    2017-10-01

    Full Text Available Phase-shifted converters are practically important to provide high conversion efficiencies through soft-switching techniques. However, the limitation on a resonant inductor current in the converters often leads to a non-fulfillment of the requirement of minimum load current. This paper presents a new power electronics control technique to enable the dual features of bi-directional power flow and an extended load range for soft-switching in phase-shift-controlled DC-DC converters. The proposed technique utilizes two identical full bridge converters and inverters in conjunction with a new control logic for gate-driving signals to facilitate both Zero Current Switching (ZCS and Zero Voltage Switching (ZVS in a single phase-shift-controlled DC-DC converter. The additional ZCS is designed for light load conditions at which the minimum load current cannot be attained. The bi-directional phase-shift-controlled DC-DC converter can implement the function of synchronous rectification. Its fast dynamic response allows for quick energy recovery during the regenerative braking of traction systems in electrified trains.

  11. Electric vehicle with or without range extender. Who is the driver - technology, customer or legislation?; Elektrofahrzeuge mit oder ohne Range Extender. Wer bestimmt den Weg - die Technik, der Kunde oder die Gesetzgebung?

    Energy Technology Data Exchange (ETDEWEB)

    Beidl, Christian; Kluin, Matthias [Technische Univ. Darmstadt (Germany); Hohenberg, Guenter; Bacher, Christian [IVD Prof. Hohenberg GmbH, Graz (Austria)

    2011-07-01

    Let us begin with an analysis of the technical context of E-mobility. The starting point of any such investigation is the restricted range of this technology. Greater car sizes bring ever-greater problems, especially in terms of the growing influence of driving speed and surrounding conditions. The combination of an E-motor and combustion engine thus represents an expedient ''enabler'' of E-mobility. This combination enables a drive system solution which overcomes the restrictions of a purely electric vehicle in terms of flexibility of use and availability of mobility. This paper discusses the difference between parallel and serial drives using already realized concepts. It also seeks to present a new concept for a compact, cost-efficient solution (ICE Assist). The second section will compare the current legal framework, customer expectations and technical solutions. Of critical importance is the concept for which the government will opt and the ''incentives'' which it sets to achieve this end. OEMs are currently beset by a significant level of insecurity regarding the concept with the best future and as a result, those involved are currently seeking solutions which cover all possible variants. This invariably results in compromises, which further add to the time and effort involved and increases costs. Customers generally have a positive attitude towards electric driving, but at the same time, their expectations follow their prior experience. Range extender / plug-in / ICE-assist solutions thus have the potential to bring a significant increase in the amount of electric driving / the number of kilometers driven by electrical means. To achieve a breakthrough in E-mobility, it is first necessary to establish a clear definition of an ''electric vehicle''. This requires a clear response from the government. 32. Internationales (orig.)

  12. A Dynamic Range Enhanced Readout Technique with a Two-Step TDC for High Speed Linear CMOS Image Sensors

    Directory of Open Access Journals (Sweden)

    Zhiyuan Gao

    2015-11-01

    Full Text Available This paper presents a dynamic range (DR enhanced readout technique with a two-step time-to-digital converter (TDC for high speed linear CMOS image sensors. A multi-capacitor and self-regulated capacitive trans-impedance amplifier (CTIA structure is employed to extend the dynamic range. The gain of the CTIA is auto adjusted by switching different capacitors to the integration node asynchronously according to the output voltage. A column-parallel ADC based on a two-step TDC is utilized to improve the conversion rate. The conversion is divided into coarse phase and fine phase. An error calibration scheme is also proposed to correct quantization errors caused by propagation delay skew within −Tclk~+Tclk. A linear CMOS image sensor pixel array is designed in the 0.13 μm CMOS process to verify this DR-enhanced high speed readout technique. The post simulation results indicate that the dynamic range of readout circuit is 99.02 dB and the ADC achieves 60.22 dB SNDR and 9.71 bit ENOB at a conversion rate of 2 MS/s after calibration, with 14.04 dB and 2.4 bit improvement, compared with SNDR and ENOB of that without calibration.

  13. Characterization of extended range Bonner Sphere Spectrometers in the CERF high-energy broad neutron field at CERN

    Science.gov (United States)

    Agosteo, S.; Bedogni, R.; Caresana, M.; Charitonidis, N.; Chiti, M.; Esposito, A.; Ferrarini, M.; Severino, C.; Silari, M.

    2012-12-01

    The accurate determination of the ambient dose equivalent in the mixed neutron-photon fields encountered around high-energy particle accelerators still represents a challenging task. The main complexity arises from the extreme variability of the neutron energy, which spans over 10 orders of magnitude or more. Operational survey instruments, which response function attempts to mimic the fluence-to-ambient dose equivalent conversion coefficient up to GeV neutrons, are available on the market, but their response is not fully reliable over the entire energy range. Extended range rem counters (ERRC) do not require the exact knowledge of the energy distribution of the neutron field and the calibration can be done with a source spectrum. If the actual neutron field has an energy distribution different from the calibration spectrum, the measurement is affected by an added uncertainty related to the partial overlap of the fluence-to-ambient dose equivalent conversion curve and the response function. For this reason their operational use should always be preceded by an "in-field" calibration, i.e. a calibration made against a reference instrument exposed in the same field where the survey-meter will be employed. In practice the extended-range Bonner Sphere Spectrometer (ERBSS) is the only device which can serve as reference instrument in these fields, because of its wide energy range and the possibility to assess the neutron fluence and the ambient dose equivalent (H*(10)) values with the appropriate accuracy. Nevertheless, the experience gained by a number of experimental groups suggests that mandatory conditions for obtaining accurate results in workplaces are: (1) the use of a well-established response matrix, thus implying validation campaigns in reference monochromatic neutrons fields, (2) the expert and critical use of suitable unfolding codes, and (3) the performance test of the whole system (experimental set-up, elaboration and unfolding procedures) in a well

  14. New records of Lophoproctus coecus Pocock, 1894 (Diplopoda, Polyxenida, Lophoproctidae extend the range of the genus Lophoproctus

    Directory of Open Access Journals (Sweden)

    Megan Short

    2015-06-01

    Full Text Available The geographic distribution of the genus Lophoproctus Pocock, 1894 has greatly expanded with new records of the species Lophoproctus coecus Pocock, 1894, together with the reassignment of a number of millipedes formerly identified as Lophoproctus lucidus (Chalande, 1888. L. coecus was found to be the sole representative of the family Lophoproctidae in collections examined from Crimea and the Caucasian region. The species was also identified from Iran and Kyrgyzstan. Lophoproctus specimens collected in Italy by Verhoeff were reassigned as L. coecus with the exception of one specimen of L. jeanneli (Brölemann, 1910 from Capri. These data were combined with all available information from the literature to look at the pattern of distribution of the four species in the genus. The range of the genus Lophoproctus extends from Portugal to Central Asia. Lophoproctus coecus is widespread from Italy eastward, while the morphologically very similar species L. lucidus is confined to France and northern Africa. The two species have a narrow overlap in the Alpes Maritimes region of France. L. jeanneli has a scattered coastal distribution around the Mediterranean Sea. The troglobitic species L. pagesi (Condé, 1982 has only been recorded from a cave on Majorca, Spain.

  15. Measurements and Monte Carlo calculations with the extended-range Bonner sphere spectrometer at high-energy mixed fields

    CERN Document Server

    AUTHOR|(INSPIRE)INSPIRE-00406842; Bay, Aurelio; Silari, Marco; Aroua, Abbas

    The use of spectrometry to provide information for neutron radiation protection has become an increasingly important activity over recent years. The need for spectral data arises because neither area survey instruments nor personal dosimeters give the correct dose equivalent results at all neutron energies. It is important therefore to know the spectra of the fields in which these devices are used. One of the systems most commonly employed in neutron spectrometry and dosimetry is the Bonner Sphere Spectrometers (BSS). The extended- range BSS that was used for this work, consists of 7 spheres with an overall response to neutrons up to 2 GeV. A 3He detector is used as a thermal counter in the centre of each sphere. In the context of this thesis the BSS was calibrated in monoenergetic neutron fields at low and intermediate energies. It was also used for measurements in several high energy mixed fields. These measurements have led to the calculation of neutron yields and spectral fluences from unshielded targets....

  16. A comperative study of different techniques for microstructural characterization of iol extended thermoplastic elastomer blends

    NARCIS (Netherlands)

    Sengupta, P.; Noordermeer, Jacobus W.M.

    2005-01-01

    This paper gives a relative comparison of different microscopic methods that are presently used to visualize polymer blend morphologies, versus the possibility to visualize the three-dimensional structure of the blends with electron tomography. Oil extended thermoplastic elastomer (TPE) blends based

  17. Bandwidth re-distribution techniques for extended epon based multi-wavelength networks

    NARCIS (Netherlands)

    Roy, R.; Manhoudt, Gert; van Etten, Wim

    2007-01-01

    The broadband photonics project (BBP) under the Freehand consortium of projects looks into the design of an extended access network. The network is a photonic network which can be dynamically reconfigured to distribute bandwidth in an optimised manner. This paper presents linear programming based

  18. Development of the Small Package Single Particle Soot Photometer with extended range (SP2-XR) and black carbon detection efficiency compared to its predecessor, the SP2

    Science.gov (United States)

    Schulz, H.; Kok, G. L.; Zanatta, M.; Schwarz, J. P.; Herber, A. B.

    2016-12-01

    Black carbon (BC) aerosol is an important contributor to climate change due to its ability to very efficiently absorb solar radiation. The Single Particle Soot Photometer (SP2) is an instrument that quantifies the refractory mass of individual BC-containing particles with a laser-induced incandescence method. The SP2 has been deployed on ships, at ground based sites, and on research aircraft to quantify BC's mass loadings and microphysical properties. However, the SP2's particle detection range is generally limited to 70-700 nm volume-equivalent diameter for ambient BC. Ambient air typically contains substantial number concentrations below and mass concentrations above the limits of this range. To account for the unquantified particles, it is common to fit a log-normal distribution to the measured size distributions — an approach that leaves the BC community with uncertain results, and a need to learn about the occurrence of very small particles or very large BC aggregates. The SP2 is also large and heavy enough to limit its usability for aircraft and unmanned or towed airborne vehicles. We have developed a miniaturized SP2 to dramatically extend the range of applications for which the SP2 technique can be used. This new instrument, with the additional target of an extended measurement range, has been named the SP2-XR, and incorporates a newly designed optical block with updated electronics for signal recording and on-the-fly processing (gain stitching and peak analysis). The optical block improves the light-collection of both scattered and incandescent light from sampled particles. The target measurement range is 40-1000 nm. At the same time, the SP2-XR weighs less than half of an SP2 (15 kg for the complete system), and about 1/4 the volume ( 20 cm x 20 cm x 40 cm). The instrument software is designed to produce ready to use particle mass and binned size distributions or full particle trace records, according to different scientific needs. Thus, an SP2-XR may

  19. Evaluation of a satellite laser ranging technique using pseudonoise code modulated laser diodes

    Science.gov (United States)

    Ball, Carolyn Kay

    1987-12-01

    Several types of Satellite Laser Ranging systems exist, operating with pulsed, high-energy lasers. The distance between a ground point and an orbiting satellite can be determined to within a few centimeters. A new technique substitutes pseudonoise code modulated laser diodes, which are much more compact, reliable and less costly, for the lasers now used. Since laser diode technology is only now achieving sufficiently powerful lasers, the capabilities of the new technique are investigated. Also examined are the effects of using an avalanche photodiode detector instead of a photomultiplier tube. The influence of noise terms (including background radiation, detector dark and thermal noise and speckle) that limit the system range and performance is evaluated.

  20. Three-dimensional near-field MIMO array imaging using range migration techniques.

    Science.gov (United States)

    Zhuge, Xiaodong; Yarovoy, Alexander G

    2012-06-01

    This paper presents a 3-D near-field imaging algorithm that is formulated for 2-D wideband multiple-input-multiple-output (MIMO) imaging array topology. The proposed MIMO range migration technique performs the image reconstruction procedure in the frequency-wavenumber domain. The algorithm is able to completely compensate the curvature of the wavefront in the near-field through a specifically defined interpolation process and provides extremely high computational efficiency by the application of the fast Fourier transform. The implementation aspects of the algorithm and the sampling criteria of a MIMO aperture are discussed. The image reconstruction performance and computational efficiency of the algorithm are demonstrated both with numerical simulations and measurements using 2-D MIMO arrays. Real-time 3-D near-field imaging can be achieved with a real-aperture array by applying the proposed MIMO range migration techniques.

  1. Reference ranges for Mexican preschool-aged children using the forced oscillation technique.

    Science.gov (United States)

    Shackleton, Claire; Barraza-Villarreal, Albino; Chen, Linping; Gangell, Catherine L; Romieu, Isabelle; Sly, Peter D

    2013-08-01

    Recently, multi-ethnic reference ranges for spirometry have been created for use worldwide. In comparison, forced oscillation technique (FOT) reference values are limited to specific equipment and study populations, with current FOT reference ranges created in a Caucasian population. We aimed to develop FOT reference ranges for preschool-aged Mexican children and to compare these with current FOT reference ranges. Respiratory resistance (Rrs) and reactance (Xrs) was measured in healthy Mexican children three to five years of age using commercial FOT equipment. The relationship between height and Rrs and Xrs was determined using regression analyses, taking into account age, weight, sex, and exposure to tobacco smoke. Reference equations were calculated for the Mexican children and Z-scores determined for Rrs and Xrs at 6 and 8Hz. A paired t-test assessed the difference in Z-scores between the Australian reference values and those created for the Mexican cohort. FOT was successfully measured in 584 children. Height was a significant predictor of Rrs and Xrs at 6 and 8Hz (Pchildren for both Rrs and Xrs at 6 and 8Hz (Pdevelopment of FOT reference ranges specific to Mexican preschool-aged children will allow for the correct interpretation of FOT measurements. This study also showed that current FOT reference ranges overestimate lung function in Mexican children. Highlighting, the importance of using ethnic appropriate reference ranges for interpreting lung function. Copyright © 2012 SEPAR. Published by Elsevier Espana. All rights reserved.

  2. Sabots, Obturator and Gas-In-Launch Tube Techniques for Heat Flux Models in Ballistic Ranges

    Science.gov (United States)

    Bogdanoff, David W.; Wilder, Michael C.

    2013-01-01

    For thermal protection system (heat shield) design for space vehicle entry into earth and other planetary atmospheres, it is essential to know the augmentation of the heat flux due to vehicle surface roughness. At the NASA Ames Hypervelocity Free Flight Aerodynamic Facility (HFFAF) ballistic range, a campaign of heat flux studies on rough models, using infrared camera techniques, has been initiated. Several phenomena can interfere with obtaining good heat flux data when using this measuring technique. These include leakage of the hot drive gas in the gun barrel through joints in the sabot (model carrier) to create spurious thermal imprints on the model forebody, deposition of sabot material on the model forebody, thereby changing the thermal properties of the model surface and unknown in-barrel heating of the model. This report presents developments in launch techniques to greatly reduce or eliminate these problems. The techniques include the use of obturator cups behind the launch package, enclosed versus open front sabot designs and the use of hydrogen gas in the launch tube. Attention also had to be paid to the problem of the obturator drafting behind the model and impacting the model. Of the techniques presented, the obturator cups and hydrogen in the launch tube were successful when properly implemented

  3. Vibration Control of a Semiactive Vehicle Suspension System Based on Extended State Observer Techniques

    Directory of Open Access Journals (Sweden)

    Ze Zhang

    2014-01-01

    Full Text Available A feedback control method based on an extended state observer (ESO method is implemented to vibration reduction in a typical semiactive suspension (SAS system using a magnetorheological (MR damper as actuator. By considering the dynamic equations of the SAS system and the MR damper model, an active disturbance rejection control (ADRC is designed based on the ESO. Numerical simulation and real-time experiments are carried out with similar vibration disturbances. Both the simulation and experimental results illustrate the effectiveness of the proposed controller in vibration suppression for a SAS system.

  4. Year-round retrievals of trace gases in the Arctic using the Extended-range Atmospheric Emitted Radiance Interferometer

    Science.gov (United States)

    Mariani, Z.; Strong, K.; Palm, M.; Lindenmaier, R.; Adams, C.; Zhao, X.; Savastiouk, V.; McElroy, C. T.; Goutail, F.; Drummond, J. R.

    2013-06-01

    The Extended-range Atmospheric Emitted Radiance Interferometer (E-AERI) was installed at the Polar Environment Atmospheric Research Laboratory (PEARL) at Eureka, Nunavut, Canada in October 2008. Spectra from the E-AERI provide information about the radiative balance and budgets of trace gases in the Canadian high Arctic. Measurements are taken every 7 min year-round, including polar night when the solar-viewing spectrometers at PEARL are not operated. This allows E-AERI measurements to fill the gap in the PEARL dataset during the four months of polar night. Measurements were taken year-round in 2008-2009 at the PEARL Ridge Lab, which is 610 m a.s.l. (above sea-level), and from 2011 onwards at the Zero-Altitude PEARL Auxiliary Lab (0PAL), which is at sea level 15 km from the Ridge Lab. Total columns of O3, CO, CH4, and N2O have been retrieved using a modified version of the SFIT2 retrieval algorithm adapted for emission spectra. This provides the first ground-based nighttime measurements of these species at Eureka. Changes in the total columns driven by photochemistry and dynamics are observed. Analyses of E-AERI retrievals indicate accurate spectral fits (root-mean-square residuals consistent with noise) and a 10-15% uncertainty in the total column, depending on the trace gas. O3 comparisons between the E-AERI and a Bruker IFS 125HR Fourier transform infrared (FTIR) spectrometer, three Brewer spectrophotometers, two UV-visible ground-based spectrometers, and a System D'Analyse par Observations Zenithales (SAOZ) at PEARL are made from 2008-2009 and for 2011. 125HR CO, CH4, and N2O columns are also compared with the E-AERI measurements. Mean relative differences between the E-AERI and the other spectrometers are 1-10% (14% is for the un-smoothed profiles), which are less than the E-AERI's total column uncertainties. The E-AERI O3 and CO measurements are well correlated with the other spectrometers (r > 0.92 with the 125HR). The 24 h diurnal cycle and 365-day seasonal

  5. Interferometric signals analysis based on the extended Kalman filter tuned by machine learning technique

    Science.gov (United States)

    Ermolaev, Petr A.; Volynsky, Maxim A.

    2017-06-01

    The paper deals with the machine learning approach to automatic tuning of extended Kalman filter in application to interferometric signals processing. The representation of interferometric signals as output of dynamic systems with varying state vector is presented. It is shown that the challenge of the extended Kalman filter application to interferometric data processing is selection of initial parameters for the filter. The complex tuning problem is described in a formal form. The machine learning approach to the automatic filter tuning is proposed. The combination of Monte Carlo optimization and the gradient descent are implemented for initial filter parameters selection. The optimization criterion in the form of sum differences between measured and estimated signal value is presented and discussed. The results of simulated and experimental interferometric signals processing are presented and analyzed. The quality of amplitude and phase estimation by the automatically tuned filter is at the same level as hand tuned filter. It is shown, that proposed approach allows to obtain robust results of experimental data processing.

  6. High range free space optic transmission using new dual diffuser modulation technique

    Science.gov (United States)

    Rahman, A. K.; Julai, N.; Jusoh, M.; Rashidi, C. B. M.; Aljunid, S. A.; Anuar, M. S.; Talib, M. F.; Zamhari, Nurdiani; Sahari, S. k.; Tamrin, K. F.; Jong, Rudiyanto P.; Zaidel, D. N. A.; Mohtadzar, N. A. A.; Sharip, M. R. M.; Samat, Y. S.

    2017-11-01

    Free space optical communication fsoc is vulnerable with fluctuating atmospheric. This paper focus analyzes the finding of new technique dual diffuser modulation (ddm) to mitigate the atmospheric turbulence effect. The performance of fsoc under the presence of atmospheric turbulence will cause the laser beam keens to (a) beam wander, (b) beam spreading and (c) scintillation. The most deteriorate the fsoc is scintillation where it affected the wavefront cause to fluctuating signal and ultimately receiver can turn into saturate or loss signal. Ddm approach enhances the detecting bit `1' and bit `0' and improves the power received to combat with turbulence effect. The performance focus on signal-to-noise (snr) and bit error rate (ber) where the numerical result shows that the ddm technique able to improves the range where estimated approximately 40% improvement under weak turbulence and 80% under strong turbulence.

  7. High range free space optic transmission using new dual diffuser modulation technique

    Directory of Open Access Journals (Sweden)

    Rahman A.K

    2017-01-01

    Full Text Available Free space optical communication fsoc is vulnerable with fluctuating atmospheric. This paper focus analyzes the finding of new technique dual diffuser modulation (ddm to mitigate the atmospheric turbulence effect. The performance of fsoc under the presence of atmospheric turbulence will cause the laser beam keens to (a beam wander, (b beam spreading and (c scintillation. The most deteriorate the fsoc is scintillation where it affected the wavefront cause to fluctuating signal and ultimately receiver can turn into saturate or loss signal. Ddm approach enhances the detecting bit ‘1’ and bit ‘0’ and improves the power received to combat with turbulence effect. The performance focus on signal-to-noise (snr and bit error rate (ber where the numerical result shows that the ddm technique able to improves the range where estimated approximately 40% improvement under weak turbulence and 80% under strong turbulence.

  8. Cost effectiveness of shortening screening interval or extending age range of NHS breast screening programme: computer simulation study

    NARCIS (Netherlands)

    R. Boer (Rob); A. Threlfall; P. Warmerdam (Peter); A. Street (Andrew); E. Friedman (Eitan); C. Woodman; H.J. de Koning (Harry)

    1998-01-01

    markdownabstract__OBJECTIVE__: To compare the cost effectiveness of two possible modifications to the current UK screening programme: shortening the screening interval from three to two years and extending the age of invitation to a final screen from 64 to 69.

  9. Evaluation of High Dynamic Range Photography as a Luminance Mapping Technique

    Energy Technology Data Exchange (ETDEWEB)

    Inanici, Mehlika; Galvin, Jim

    2004-12-30

    The potential, limitations, and applicability of the High Dynamic Range (HDR) photography technique is evaluated as a luminance mapping tool. Multiple exposure photographs of static scenes are taken with a Nikon 5400 digital camera to capture the wide luminance variation within the scenes. The camera response function is computationally derived using the Photosphere software, and is used to fuse the multiple photographs into HDR images. The vignetting effect and point spread function of the camera and lens system is determined. Laboratory and field studies have shown that the pixel values in the HDR photographs can correspond to the physical quantity of luminance with reasonable precision and repeatability.

  10. An extended algebraic reconstruction technique (E-ART) for dual spectral CT.

    Science.gov (United States)

    Zhao, Yunsong; Zhao, Xing; Zhang, Peng

    2015-03-01

    Compared with standard computed tomography (CT), dual spectral CT (DSCT) has many advantages for object separation, contrast enhancement, artifact reduction, and material composition assessment. But it is generally difficult to reconstruct images from polychromatic projections acquired by DSCT, because of the nonlinear relation between the polychromatic projections and the images to be reconstructed. This paper first models the DSCT reconstruction problem as a nonlinear system problem; and then extend the classic ART method to solve the nonlinear system. One feature of the proposed method is its flexibility. It fits for any scanning configurations commonly used and does not require consistent rays for different X-ray spectra. Another feature of the proposed method is its high degree of parallelism, which means that the method is suitable for acceleration on GPUs (graphic processing units) or other parallel systems. The method is validated with numerical experiments from simulated noise free and noisy data. High quality images are reconstructed with the proposed method from the polychromatic projections of DSCT. The reconstructed images are still satisfactory even if there are certain errors in the estimated X-ray spectra.

  11. Extending battery life: A low-cost practical diagnostic technique for lithium-ion batteries

    Science.gov (United States)

    Merla, Yu; Wu, Billy; Yufit, Vladimir; Brandon, Nigel P.; Martinez-Botas, Ricardo F.; Offer, Gregory J.

    2016-11-01

    Modern applications of lithium-ion batteries such as smartphones, hybrid & electric vehicles and grid scale electricity storage demand long lifetime and high performance which typically makes them the limiting factor in a system. Understanding the state-of-health during operation is important in order to optimise for long term durability and performance. However, this requires accurate in-operando diagnostic techniques that are cost effective and practical. We present a novel diagnosis method based upon differential thermal voltammetry demonstrated on a battery pack made from commercial lithium-ion cells where one cell was deliberately aged prior to experiment. The cells were in parallel whilst being thermally managed with forced air convection. We show for the first time, a diagnosis method capable of quantitatively determining the state-of-health of four cells simultaneously by only using temperature and voltage readings for both charge and discharge. Measurements are achieved using low-cost thermocouples and a single voltage measurement at a frequency of 1 Hz, demonstrating the feasibility of implementing this approach on real world battery management systems. The technique could be particularly useful under charge when constant current or constant power is common, this therefore should be of significant interest to all lithium-ion battery users.

  12. Evaluation and Management of Human Errors in Critical Processes of Hospital Using the Extended CREAM Technique

    Directory of Open Access Journals (Sweden)

    Iraj Mohammadfam

    2017-07-01

    Full Text Available Medical errors result in serious and often-preventable problems for patients. Human errors can be used as an opportunity for learning as well as a key factor for patients’ safety improvement and quality of patients' surveillance in hospitals. The aim of the present study was to identify and evaluate human errors to help reduce risks among personnel who render health services during critical hospital processes. This cross-sectional study was done in the Besat hospital in Hamedan in 2016. At first, the critical processes were selected via given scores in Delphi method and by multiplying the scores of each of the five criteria including the severity of the consequences caused by error incidence, probability of error, capability of the error detection, task repeatability and type of hospital ward with each other. Determining the risk numbers of each process, three ones were chosen with the largest scores. At the end, the selected processes were analyzed by the method of extended CREAM. The results showed that the highest CFP is associated with the CPR process, particularly in the sub-stage of command of starting CPR by anesthesiologists (0.0891, the one in the giving medicine process is in the sub-stage of calculating of medicine dozes and determining prescription methods (0.0796 and also the one in the tracheal intubation process is in the sub-stages of pulmonary and respiratory monitoring of patients and observing the vocal cords and larynx of patients (0.0350. Regarding the critical consequences of human errors in the selected processes, reviewing the qualities of roles and responsibilities of each of the medical group members and providing specialized introduction for hospital processes seem necessary.

  13. Extended Closed-form Expressions for the Robust Symmetrical Number System Dynamic Range and an Efficient Algorithm for its Computation

    Science.gov (United States)

    2014-01-01

    ending position, Stop Case of M̂ is Case 220. The value of m was plotted against the value of M̂ , and the data was curve fitted to a quadratic polynomial ...kth prime . It is well–known (and easily derivable by using the prime number theorem [17]) that PN# = exp[(1 + o(1))n log n]. Assume N ≥ 6. It is...Theory IEEE TRANSACTIONS ON INFORMATION THEORY, VOL. XX, NO. XX, MONTH YEAR 1 Extended Closed-form Expressions for the Robust Symmetrical Number

  14. A survey of actuator shaft sealing techniques for extended space missions

    Science.gov (United States)

    Hotz, G. M.

    1972-01-01

    Actuators for control and articulation aboard Mariner spacecraft have employed output shaft seals to maintain an internal gaseous atmosphere. On future missions, considerably greater expected lifetimes, temperature ranges, and radiation exposures have led to a need to determine the limitations of the present O-ring output shaft seal and to examine other candidate seals. Seals suited both to dynamic and static sealing were examined for potential use in three specific actuator applications and the following candidate seals were selected: (a) O-ring seal, (b) chevron seal, (c) bellows seal (linear actuator only), (d) magnetic fluid seal (rotary actuators only) and as a backup seal to any of the foregoing, (e) the labyrinth seal.

  15. Survey on Ranging Sensors and Cooperative Techniques for Relative Positioning of Vehicles

    Directory of Open Access Journals (Sweden)

    Fabian de Ponte Müller

    2017-01-01

    Full Text Available Future driver assistance systems will rely on accurate, reliable and continuous knowledge on the position of other road participants, including pedestrians, bicycles and other vehicles. The usual approach to tackle this requirement is to use on-board ranging sensors inside the vehicle. Radar, laser scanners or vision-based systems are able to detect objects in their line-of-sight. In contrast to these non-cooperative ranging sensors, cooperative approaches follow a strategy in which other road participants actively support the estimation of the relative position. The limitations of on-board ranging sensors regarding their detection range and angle of view and the facility of blockage can be approached by using a cooperative approach based on vehicle-to-vehicle communication. The fusion of both, cooperative and non-cooperative strategies, seems to offer the largest benefits regarding accuracy, availability and robustness. This survey offers the reader a comprehensive review on different techniques for vehicle relative positioning. The reader will learn the important performance indicators when it comes to relative positioning of vehicles, the different technologies that are both commercially available and currently under research, their expected performance and their intrinsic limitations. Moreover, the latest research in the area of vision-based systems for vehicle detection, as well as the latest work on GNSS-based vehicle localization and vehicular communication for relative positioning of vehicles, are reviewed. The survey also includes the research work on the fusion of cooperative and non-cooperative approaches to increase the reliability and the availability.

  16. Survey on Ranging Sensors and Cooperative Techniques for Relative Positioning of Vehicles.

    Science.gov (United States)

    de Ponte Müller, Fabian

    2017-01-31

    Future driver assistance systems will rely on accurate, reliable and continuous knowledge on the position of other road participants, including pedestrians, bicycles and other vehicles. The usual approach to tackle this requirement is to use on-board ranging sensors inside the vehicle. Radar, laser scanners or vision-based systems are able to detect objects in their line-of-sight. In contrast to these non-cooperative ranging sensors, cooperative approaches follow a strategy in which other road participants actively support the estimation of the relative position. The limitations of on-board ranging sensors regarding their detection range and angle of view and the facility of blockage can be approached by using a cooperative approach based on vehicle-to-vehicle communication. The fusion of both, cooperative and non-cooperative strategies, seems to offer the largest benefits regarding accuracy, availability and robustness. This survey offers the reader a comprehensive review on different techniques for vehicle relative positioning. The reader will learn the important performance indicators when it comes to relative positioning of vehicles, the different technologies that are both commercially available and currently under research, their expected performance and their intrinsic limitations. Moreover, the latest research in the area of vision-based systems for vehicle detection, as well as the latest work on GNSS-based vehicle localization and vehicular communication for relative positioning of vehicles, are reviewed. The survey also includes the research work on the fusion of cooperative and non-cooperative approaches to increase the reliability and the availability.

  17. Adapting range migration techniques for imaging with metasurface antennas: analysis and limitations

    Science.gov (United States)

    Pulido Mancera, Laura; Fromenteze, Thomas; Sleasman, Timothy; Boyarsky, Michael; Imani, Mohammadreza F.; Reynolds, Matthew S.; Smith, David R.

    2017-04-01

    Dynamic metasurface antennas are planar structures that exhibit remarkable capabilities in controlling electromagnetic wave-fronts, advantages which are particularly attractive for microwave imaging. These antennas exhibit strong frequency dispersion and produce diverse radiation patterns. Such behavior presents unique challenges for integration with conventional imaging algorithms. We analyze an adapted version of the range migration algorithm (RMA) for use with dynamic metasurfaces in image reconstruction. Focusing on the the proposed pre-processing step, that ultimately allows a fast processing of the backscattered signal in the spatial frequency domain from which the fast Fourier transform can efficiently reconstruct the scene. Numerical studies illustrate imaging performance using both conventional methods and the adapted RMA, demonstrating that the RMA can reconstruct images with comparable quality in a fraction of the time. In this paper, we demonstrate the capabilities of the algorithm as a fast reconstruction tool, and we analyze the limitations of the presented technique in terms of image quality.

  18. New Diagnostic, Launch and Model Control Techniques in the NASA Ames HFFAF Ballistic Range

    Science.gov (United States)

    Bogdanoff, David W.

    2012-01-01

    This report presents new diagnostic, launch and model control techniques used in the NASA Ames HFFAF ballistic range. High speed movies were used to view the sabot separation process and the passage of the model through the model splap paper. Cavities in the rear of the sabot, to catch the muzzle blast of the gun, were used to control sabot finger separation angles and distances. Inserts were installed in the powder chamber to greatly reduce the ullage volume (empty space) in the chamber. This resulted in much more complete and repeatable combustion of the powder and hence, in much more repeatable muzzle velocities. Sheets of paper or cardstock, impacting one half of the model, were used to control the amplitudes of the model pitch oscillations.

  19. Project Milestone. Analysis of Range Extension Techniques for Battery Electric Vehicles

    Energy Technology Data Exchange (ETDEWEB)

    Neubauer, Jeremy [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Wood, Eric [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Pesaran, Ahmad [National Renewable Energy Laboratory (NREL), Golden, CO (United States)

    2013-07-01

    This report documents completion of the July 2013 milestone as part of NREL’s Vehicle Technologies Annual Operating Plan with the U.S. Department of Energy. The objective was to perform analysis on range extension techniques for battery electric vehicles (BEVs). This work represents a significant advancement over previous thru-life BEV analyses using NREL’s Battery Ownership Model, FastSim,* and DRIVE.* Herein, the ability of different charging infrastructure to increase achievable travel of BEVs in response to real-world, year-long travel histories is assessed. Effects of battery and cabin thermal response to local climate, battery degradation, and vehicle auxiliary loads are captured. The results reveal the conditions under which different public infrastructure options are most effective, and encourage continued study of fast charging and electric roadway scenarios.

  20. Flexibility in food extraction techniques in urban free-ranging bonnet macaques, Macaca radiata.

    Directory of Open Access Journals (Sweden)

    Madhur Mangalam

    Full Text Available Non-human primate populations, other than responding appropriately to naturally occurring challenges, also need to cope with anthropogenic factors such as environmental pollution, resource depletion, and habitat destruction. Populations and individuals are likely to show considerable variations in food extraction abilities, with some populations and individuals more efficient than others at exploiting a set of resources. In this study, we examined among urban free-ranging bonnet macaques, Macaca radiata (a local differences in food extraction abilities, (b between-individual variation and within-individual consistency in problem-solving success and the underlying problem-solving characteristics, and (c behavioral patterns associated with higher efficiency in food extraction. When presented with novel food extraction tasks, the urban macaques having more frequent exposure to novel physical objects in their surroundings, extracted food material from PET bottles and also solved another food extraction task (i.e., extracting an orange from a wire mesh box, more often than those living under more natural conditions. Adults solved the tasks more frequently than juveniles, and females more frequently than males. Both solution-technique and problem-solving characteristics varied across individuals but remained consistent within each individual across the successive presentations of PET bottles. The macaques that solved the tasks showed lesser within-individual variation in their food extraction behavior as compared to those that failed to solve the tasks. A few macaques appropriately modified their problem-solving behavior in accordance with the task requirements and solved the modified versions of the tasks without trial-and-error learning. These observations are ecologically relevant - they demonstrate considerable local differences in food extraction abilities, between-individual variation and within-individual consistency in food extraction

  1. Literature searching for social science systematic reviews: consideration of a range of search techniques.

    Science.gov (United States)

    Papaioannou, Diana; Sutton, Anthea; Carroll, Christopher; Booth, Andrew; Wong, Ruth

    2010-06-01

    Literature for a systematic review on the student experience of e-learning is located across a range of subject areas including health, education, social science, library and information science. To assess the merits and shortcomings of using different search techniques in retrieval of evidence in the social science literature. A conventional subject search was undertaken as the principal method of identifying the literature for the review. Four supplementary search methods were used including citation searching, reference list checking, contact with experts and pearl growing. The conventional subject search identified 30 of 41 included references; retrieved from 10 different databases. References were missed by this method and a further 11 references were identified via citation searching, reference list checking and contact with experts. Pearl growing was suspended as the nominated pearls were dispersed across numerous databases, with no single database indexing more than four pearls. Searching within the social sciences literature requires careful consideration. Conventional subject searching identified the majority of references, but additional search techniques were essential and located further high quality references.

  2. Cannon Wear and Erosion Science and Technology Objective Program (STO) 155-mm Projectile Rotating Band/Obturation for Extended Range

    Science.gov (United States)

    2015-06-01

    models and body engraving models have been developed to aid in the design of new bands. Welding techniques and parameters for soft iron, nickel, MONEL...sticker test 21 TABLES 1 Candidate materials for rotating bands 7 2 Characterization of as- welded and fired bands 8 3 Mass properties...muzzle velocity (increased spin and frictional heating), poor obturation, and bore surface effects caused rapid heating and melting of the copper band

  3. Extending the Collection Duration of Breath Samples for Enteric Methane Emission Estimation Using the SF6 Tracer Technique

    Science.gov (United States)

    Pinares-Patiño, César; Gere, José; Williams, Karen; Gratton, Roberto; Juliarena, Paula; Molano, German; MacLean, Sarah; Sandoval, Edgar; Taylor, Grant; Koolaard, John

    2012-01-01

    Simple Summary Extended sample collection for the SF6 tracer technique is desirable for extensive grazing systems. Breath samples from eight cows were collected while lucerne silage was fed to achieve fixed intakes among the cows. Samples were collected over a 10-day period, using either apparatuses used in New Zealand (NZL) or Argentina (ARG), and either daily, over two consecutive 5-day periods or over a 10-day period (in duplicate). The NZL system had a greater sampling success and more consistent CH4 emission estimates than the ARG system, with no differences in mean emissions among sample collection periods. This study showed that extended sample collection is feasible, but definitive evaluation under grazing situation is required before a decision on recommendation can be made. Abstract The daily sample collection protocol of the sulphur hexafluoride (SF6) tracer technique for the estimation of methane (CH4) emissions from ruminants may not be practical under extensive grazing systems. Here, under controlled conditions, we evaluated extended periods of sampling as an alternative to daily sample collections. Eight rumen-fistulated cows were housed and fed lucerne silage to achieve common daily feed intakes of 6.4 kg dry matter per cow. Following SF6 permeation tube dosing, eight sampling lines were fitted to the breath collection harness, so that a common gas mix was available to each line. Half of the lines collected samples into PVC yokes using a modified capillary system as commonly used in New Zealand (NZL), and half collected samples into stainless steel cylinders using a ball-bearing flow restrictor as used in Argentina (ARG), all within a 10-day time frame, either daily, across two consecutive 5-day periods or across one 10-day period (in duplicate). The NZL system had greater sampling success (97.3 vs. 79.5%) and yielded more consistent CH4 emission estimates than the ARG system. Emission estimates from NZL daily, NZL 5-day and NZL 10-day samplings

  4. LysM domains mediate lipochitin-oligosaccharide recognition and Nfr genes extend the symbiotic host range

    DEFF Research Database (Denmark)

    Radutoiu, Simona; Madsen, Lene H; Madsen, Esben B

    2007-01-01

    Legume-Rhizobium symbiosis is an example of selective cell recognition controlled by host/non-host determinants. Individual bacterial strains have a distinct host range enabling nodulation of a limited set of legume species and vice versa. We show here that expression of Lotus japonicus Nfr1...

  5. Zygomatic implant placement in conjunction with sinus bone grafting: the "extended sinus elevation technique." a case-cohort study.

    Science.gov (United States)

    Hinze, Marc; Vrielinck, Luc; Thalmair, Tobias; Wachtel, Hannes; Bolz, Wolfgang

    2013-01-01

    The zygomatic implant is mainly indicated for the rehabilitation of extremely atrophied maxillae when bone augmentation should be avoided. One drawback of zygomatic implants, which typically pass through the sinus, is initial or late bone resorption around the implant neck, which can result in oroantral communications followed by possible infection of the sinus. To decrease the risk of sinus infection, a modified technique was developed to preserve the integrity of the sinus membrane and to regenerate bone around zygomatic implants using an extended sinus grafting approach. Patients with extremely atrophied maxillae were provided with one to four zygomatic implants in conjunction with sinus grafting, plus conventional auxiliary implants, for immediate support of a provisional full-arch maxillary prosthesis. Definitive prostheses were delivered at 6 months after implant placement. All patients underwent clinical and radiographic examinations at 6 months. Twenty-two zygomatic and 23 conventional auxiliary implants were placed in 10 patients. The overall 6-month implant survival rate was 90.9% for zygomatic implants and 100% for auxiliary implants placed in the anterior area. Only two minor technical complications were seen, and clinical indicators (including probing pocket depth, keratinized tissue, and plaque and bleeding indices) were good in all patients. A substantial gain of radiographic bone around the zygomatic implants was observed. The proposed technique led to successful prosthetic function for all patients. With the described technique, exposed implant threads within the maxillary antrum are eliminated and the potential for biologic complications is minimized.

  6. Measurements of the conduction of heat in water vapor, nitrogen and mixtures of these gases in an extended temperature range

    Science.gov (United States)

    Frohn, A.; Westerdorf, M.

    Experimental and analytical results are presented from trials with heat conduction in water vapor, nitrogen, and mixtures of the two in a cylindrical heat transfer cell. The pressures examined ranged from 100-0.01 mbar, corresponding to Knudsen numbers of 0.01-100. Formulations are defined for the continuum conditions, the free molecule conditions, the transition region, and the momentum equation solution. Experimentation with an instrumented configuration of an inner and outer cylinder over the temperature range 300-725 K is described, noting the use of a vacuum around the inner, gas-filled container in order to measure the radiative heat losses. The results are useful for predicting heat transfer in high altitude flight or among small droplets in natural fogs, cooling towers, and combustion chambers.

  7. A Dual Active Bridge Converter with an Extended High-Efficiency Range by DC Blocking Capacitor Voltage Control

    DEFF Research Database (Denmark)

    Qin, Zian; Shen, Yanfeng; Loh, Poh Chiang

    2017-01-01

    A Dual Active Bridge (DAB) converter can achieve a wide high-efficiency range when its input and output voltages are equal, assuming a 1:1 turns ratio for its isolation transformer. If its input or output voltage is doubled, efficiency of the DAB will drop significantly, because of the introduction...... of hard switching and high circulating power. Thus, a new modulation scheme has been proposed, whose main idea is to introduce a voltage offset across the dc blocking capacitor connected in series with the transformer. Operational principle of the proposed modulation has been introduced, before analyzing...

  8. InGaP-based InP quantum dot solar cells with extended optical absorption range

    Science.gov (United States)

    Aihara, Taketo; Tayagaki, Takeshi; Nagato, Yuki; Okano, Yoshinobu; Sugaya, Takeyoshi

    2017-04-01

    In the quest for an efficient optical absorption of broad-band solar irradiation, intermediate-band solar cells composed of wide-bandgap semiconductors have attracted attention. In the present study, we developed and investigated the performance of wide-bandgap InGaP-based InP quantum dot (QD) solar cells. The solar cells were fabricated by solid-source molecular beam epitaxy, and their optical absorption range was found to be up to ∼850 nm, which is larger than the ∼680 nm optical absorption range of the host InGaP solar cells. Through the measurements of the voltage-dependent quantum efficiency, the photocarriers generated in the InGaP host were determined to be captured into the InP QDs, rather than expelled from the solar cells. The findings of this study highlight the need for the development of an optimized structure of intermediate-band solar cells to mitigate the capture of the photocarriers.

  9. Theoretical detection threshold of the proton-acoustic range verification technique

    Energy Technology Data Exchange (ETDEWEB)

    Ahmad, Moiz; Yousefi, Siavash; Xing, Lei, E-mail: lei@stanford.edu [Department of Radiation Oncology, Stanford University School of Medicine, Stanford, California 94305-5847 (United States); Xiang, Liangzhong [Center for Bioengineering and School of Electrical and Computer Engineering, University of Oklahoma, Norman, Oklahoma 73019-1101 (United States)

    2015-10-15

    Purpose: Range verification in proton therapy using the proton-acoustic signal induced in the Bragg peak was investigated for typical clinical scenarios. The signal generation and detection processes were simulated in order to determine the signal-to-noise limits. Methods: An analytical model was used to calculate the dose distribution and local pressure rise (per proton) for beams of different energy (100 and 160 MeV) and spot widths (1, 5, and 10 mm) in a water phantom. In this method, the acoustic waves propagating from the Bragg peak were generated by the general 3D pressure wave equation implemented using a finite element method. Various beam pulse widths (0.1–10 μs) were simulated by convolving the acoustic waves with Gaussian kernels. A realistic PZT ultrasound transducer (5 cm diameter) was simulated with a Butterworth bandpass filter with consideration of random noise based on a model of thermal noise in the transducer. The signal-to-noise ratio on a per-proton basis was calculated, determining the minimum number of protons required to generate a detectable pulse. The maximum spatial resolution of the proton-acoustic imaging modality was also estimated from the signal spectrum. Results: The calculated noise in the transducer was 12–28 mPa, depending on the transducer central frequency (70–380 kHz). The minimum number of protons detectable by the technique was on the order of 3–30 × 10{sup 6} per pulse, with 30–800 mGy dose per pulse at the Bragg peak. Wider pulses produced signal with lower acoustic frequencies, with 10 μs pulses producing signals with frequency less than 100 kHz. Conclusions: The proton-acoustic process was simulated using a realistic model and the minimal detection limit was established for proton-acoustic range validation. These limits correspond to a best case scenario with a single large detector with no losses and detector thermal noise as the sensitivity limiting factor. Our study indicated practical proton

  10. Theoretical detection threshold of the proton-acoustic range verification technique.

    Science.gov (United States)

    Ahmad, Moiz; Xiang, Liangzhong; Yousefi, Siavash; Xing, Lei

    2015-10-01

    Range verification in proton therapy using the proton-acoustic signal induced in the Bragg peak was investigated for typical clinical scenarios. The signal generation and detection processes were simulated in order to determine the signal-to-noise limits. An analytical model was used to calculate the dose distribution and local pressure rise (per proton) for beams of different energy (100 and 160 MeV) and spot widths (1, 5, and 10 mm) in a water phantom. In this method, the acoustic waves propagating from the Bragg peak were generated by the general 3D pressure wave equation implemented using a finite element method. Various beam pulse widths (0.1-10 μs) were simulated by convolving the acoustic waves with Gaussian kernels. A realistic PZT ultrasound transducer (5 cm diameter) was simulated with a Butterworth bandpass filter with consideration of random noise based on a model of thermal noise in the transducer. The signal-to-noise ratio on a per-proton basis was calculated, determining the minimum number of protons required to generate a detectable pulse. The maximum spatial resolution of the proton-acoustic imaging modality was also estimated from the signal spectrum. The calculated noise in the transducer was 12-28 mPa, depending on the transducer central frequency (70-380 kHz). The minimum number of protons detectable by the technique was on the order of 3-30 × 10(6) per pulse, with 30-800 mGy dose per pulse at the Bragg peak. Wider pulses produced signal with lower acoustic frequencies, with 10 μs pulses producing signals with frequency less than 100 kHz. The proton-acoustic process was simulated using a realistic model and the minimal detection limit was established for proton-acoustic range validation. These limits correspond to a best case scenario with a single large detector with no losses and detector thermal noise as the sensitivity limiting factor. Our study indicated practical proton-acoustic range verification may be feasible with approximately 5

  11. New distribution and genetic data extend the ranges of the spectacled salamanders, genus Salamandrina, in the Apulia region (South Italy

    Directory of Open Access Journals (Sweden)

    Cristiano Liuzzi

    2011-12-01

    Full Text Available Additional data on the distribution of the genus Salamandrina in the Apulia region (southern Italy are provided. Based on fieldwork carried out from May to August 2011 in two new localities, Volturara Appula (Foggia province and Spinazzola (Barletta province, the presence of Salamandrina species was recorded. Results from the genetic analyses of the 12S rRNA gene fragment from six individuals demonstrated that S. perspicillata occurs in Volturara Appula while S. terdigitata in the Spinazzola locality. The latter species is reported for the first time for the Apulia region. These new distribution data represent considerable range extensions for the Salamandrina species, indicating that more surveys are needed to complement the existing knowledge on their distribution as well as of the herpetofauna from the Apulia region. The conservation implications of our findings are also discussed.

  12. GNSS single frequency ionospheric range delay corrections: NeQuick data ingestion technique

    Science.gov (United States)

    Oladipo, O. A.; Schüler, Torben

    2012-11-01

    A study of the performance of the NeQuick model and the Klobuchar model for GNSS single frequency range delay correction on a global scale was done using data for moderate solar activity. In this study NeQuick was used in the way intended for Galileo. This study is to assess the performance of the two models at each ionospheric geographic region during moderate solar activity as previously published studies were concentrated only on high solar activity. The results obtained showed that NeQuick outperformed Klobuchar for the whole year at the three geographical regions of the ionosphere. In terms of monthly root mean square of mismodeling, NeQuick outperformed Klobuchar by 15 TECU or more at low-latitudes, 5 TEC or more at mid-latitudes, and 1 TECU or more at high-latitudes. Also, a study on how the data ingestion technique already developed for NeQuick could be expanded in order to reduce the deviation of NeQuick TEC prediction from observation for a particular day based on the information from the previous day was done. Instead of obtaining a regularly spaced Az grid from monitoring stations spread across the region of interest, we obtained hourly Az coefficients from hourly Az from designated monitoring stations. The obtained hourly Az coefficients were then used to drive NeQuick for the next day at the test stations. The results obtained, in terms of daily RMS of mismodeling, showed a daily maximum improvement of 26.0% at low-latitudes, 54.9% at mid-latitudes, and 41.3% at high-latitudes.

  13. If you can't dazzle them with brilliance, baffle them with nonsense: extending the impact of the disrupt-then-reframe technique of social influence.

    NARCIS (Netherlands)

    Fennis, B.M.; Das, Enny H.H.J; Pruyn, Adriaan T.H.

    2004-01-01

    Three experiments extended earlier findings on the impact of the Disrupt-Then-Reframe (DTR) technique on compliance. This technique is comprised of a subtle, odd element in a typical scripted request, the "disruption," followed by a persuasive phrase, the "reframing." Based on the thought-disruption

  14. [S2-Ala-iliac screws for extended pelvic fixation in longer lumbar instrumentations : Description of a freehand technique].

    Science.gov (United States)

    Lattig, F; Weckbach, S

    2017-08-01

    To reduce the rate of implant failures at the lumbosacral junction in polysegmental lumbar fusions. Spinal fusion with deformity correction including L5/S1, revision surgery for pseudoarthrosis L5/S1, screw pull-out and pedicle fractures in S1, and S1/S2 fractures after polysegmental fusions. Osteosynthesis of complex pelvic ring fractures, tumors of the ilium. Relative contraindication: infection, to avoid contamination of the iliosacral joint. Conventional posterior approach to the lumbar spine. Positioning of the lumbar and S1 pedicle screws in common technique. Identification of the correct entrance point for one or two S2-Ala-iliac screws for each side and preparation of the drill holes in freehand technique. Connection of the lumbar and S1 pedicle screws and S2-Ala-iliac screws with one stress-free rod on each side without the use of connectors or special plates. Back-friendly mobilization beginning on day 1 after surgery with support of a physiotherapist. No sports for 12 weeks. In all, 25 patients were treated with an extended pelvic fixation using S2-Ala-iliac screws. A primary deformity correction was performed in 11 patients, whereas 14 patients underwent revision surgery. A total of 24 patients were clinically and radiologically followed for a mean of 16 months. Two patients showed a loosening of the S2-Ala-iliac screws on one side, and one patient had broken screw as well only on one side without clinical symptoms. So far, no patient has undergone revision surgery because of S2-Ala-iliac screw-associated complications.

  15. Extended dynamic range of Doppler OCT by application of a new method to high density B-scans using a MHz FDML swept laser source (Conference Presentation)

    Science.gov (United States)

    Elahi, Sahar; Thrane, Lars; Rollins, Andrew M.; Jenkins, Michael W.

    2017-02-01

    The limited dynamic range of optical coherence tomography (OCT) Doppler velocity measurements makes it difficult to conduct experiments on samples requiring a large dynamic range without phase wrapping at high velocities or loss of sensitivity at slow velocities. Hemodynamics and wall motion undergo significant increases in velocity as the embryonic heart develops. Experimental studies indicate that altered hemodynamics in early-stage embryonic hearts can lead to congenital heart diseases (CHDs), motivating close monitoring of blood flow over several stages of development. We have built a high-speed OCT system using an FDML laser (Optores GmbH, Germany) at a sweep rate of 1.68 MHz (axial resolution - 12 μm, sensitivity - 105 dB, phase stability - 17 mrad). The speed of this OCT system allows us to acquire high-density B-scans to obtain an extended velocity dynamic range without sacrificing the frame rate (100 Hz). The extended dynamic range within a frame is achieved by varying the A-scan interval at which the phase difference is found, enabling detection of velocities ranging from tens of microns per second to hundreds of millimeters per second. The extra lines in a frame can also be utilized to improve the structural and Doppler images via complex averaging. In structural images where the presence of blood causes additional scattering, complex averaging helps retrieve features located deeper in the tissue. Moreover, high-density frames can be registered to 4D volumes to determine the orthogonal direction of flow for calculating shear stress as well as estimating the cardiac output. In conclusion, high density B-scans acquired by our high-speed OCT system enable image enhancement and direct measurement of biological parameters in cohort studies.

  16. The awake endoscope-guided sealant technique with fibrin glue in the treatment of postoperative cerebrospinal fluid leak after extended transsphenoidal surgery: technical note.

    Science.gov (United States)

    Cavallo, Luigi M; Solari, Domenico; Somma, Teresa; Savic, Dragan; Cappabianca, Paolo

    2014-01-01

    The introduction of extended endoscopic endonasal approaches for the management of midline skull base lesions has brought again the focus on the problem of postoperative cerebrospinal fluid (CSF) leak management. Notwithstanding the improvements in reconstruction techniques that have reduced the rate of postoperative CSF leakage, no technique has proven to be thoroughly effective. Nine patients complaining of postoperative CSF leaking after extended endoscopic endonasal surgery for different suprasellar lesions were managed without reoperation by means of repeated endoscopic endonasal fibrin glue injections in the sphenoid sinus cavity while they were awake in the outpatient operating room. Only a few patients required light sedation with benzodiazepine. To help the healing process, lumbar CSF diversion was used in four patients who complained of moderate and severe leaks, We achieved an effective and resilient closure of the skull-base defect in all cases who underwent the endoscope-guided fibrin glue injection for the management of postoperative CSF leak after endoscopic endonasal surgery. Of the four patients presenting a "weeping" leak, one patient required a single injection, whereas three required two procedures; no lumbar drainage was used. Two patients with "moderate" leaks received four injections and in both a lumbar drain also was positioned. In the other two patients, three (in this case a lumbar drain was used) and two injections were performed, respectively. We managed the patient with severe leaking by performing an injection five times, and lumbar drainage was placed. No complications related to procedure or to the use of this material were observed (mean follow-up, 26.6 months; range, 5-63). An endoscope-guided sealant technique with fibrin glue used while the patient is awake has proven, in our experience, to be effective in reducing the rate of reoperations in the management of postoperative CSF leaking after endoscopic endonasal approaches for

  17. Methods for root effects, tip effects and extending the angle of attack range to {+-} 180 deg., with application to aerodynamics for blades on wind turbines and propellers

    Energy Technology Data Exchange (ETDEWEB)

    Montgomerie, Bjoern

    2004-06-01

    For wind turbine and propeller performance calculations aerodynamic data, valid for several radial stations along the blade, are used. For wind turbines the data must be valid for the 360 degree angle of attack range. The reason is that all kinds of abnormal conditions must be analysed especially during the design of the turbine. Frequently aerodynamic data are available from wind tunnel tests where the angle of attack range is from say -5 to +20 degrees. This report describes a method to extend such data to be valid for {+-} 180 degrees. Previously the extension of data has been very approximate following the whim of the moment with the analyst. Furthermore, the Himmelskamp effect at the root and tip effects are treated in the complete method.

  18. Automated assessment of blood flow in developing embryonic hearts by extending dynamic range of Doppler OCT using a MHz FDML swept laser source (Conference Presentation)

    Science.gov (United States)

    Elahi, Sahar; Thrane, Lars; Rollins, Andrew M.; Jenkins, Michael W.

    2017-02-01

    Altered hemodynamics in developing embryonic hearts lead to congenital heart diseases, motivating close monitoring of blood flow over several stages of development. Doppler OCT can assess blood flow in tubular hearts, but the maximum velocity increases drastically during the period of cardiac cushion (valve precursors) formation. Therefore, the limited dynamic range of Doppler OCT velocity measurement makes it difficult to conduct longitudinal studies without phase wrapping at high velocities or loss of sensitivity to slow velocities. We have built a high-speed OCT system using an FDML laser (Optores GmbH, Germany) at a sweep rate of 1.68 MHz (axial resolution - 12 μm, sensitivity - 105 dB, phase stability - 17 mrad). The speed of this OCT system allows us to acquire high-density B-scans to obtain an extended velocity dynamic range without sacrificing the frame rate. The extended dynamic range within a frame is achieved by varying the A-scan interval at which the phase difference is found, enabling detection of velocities ranging from tens of microns per second to hundreds of mm per second. The extra lines in a frame can also be utilized to improve the structural and Doppler images via complex averaging. In structural images where presence of blood causes additional scattering, complex averaging helps retrieve features located deeper in the tissue. Moreover, high-density frames can be registered to 4D volumes to determine the orthogonal direction of flow and calculate shear stress. In conclusion, our high-speed OCT system will enable automated Doppler imaging of embryonic hearts in cohort studies.

  19. Effect of tissue heterogeneity on an in vivo range verification technique for proton therapy

    Science.gov (United States)

    Hassane Bentefour, El; Shikui, Tang; Prieels, Damien; Lu, Hsiao-Ming

    2012-09-01

    It was proposed recently that time-resolved dose measurements during proton therapy treatment by passively scattered beams may be used for in vivo range verification. The method was shown to work accurately in a water tank. In this paper, we further evaluated the potential of the method for more clinically relevant situations where proton beams must pass through regions with significant tissue heterogeneities. Specifically, we considered prostate treatment where the use of anterior or anterior- oblique fields was recently proposed in order to reduce rectal dose by taking advantage of the sharp distal fall-off of the Bragg peak. These beam portals pass through various parts of pubic bone and potential air cavities in the bladder and bowels. Using blocks of materials with densities equivalent to bone, air, etc, arranged in the water tank in relevant configurations, we tested the robustness of the method against range shifting and range mixing. In the former, the beam range is changed uniformly by changes in tissue density in the beam path, while in the latter, variations in tissue heterogeneities across the beam cross section causes the mixing of beam energies downstream, as often occurs when the beam travels along the interface of materials with significantly different densities. We demonstrated that in the region of interest, the method can measure water-equivalent path length with accuracy better than ±0.5 mm for pure range shifting and still reasonable accuracy for range mixing between close beam energies. In situations with range mixing between significantly different beam energies, the dose rate profiles may be simulated for verifying the beam range. We also found that the above performances can be obtained with very small amount of dose (diodes are used as detectors. This makes the method suitable for in vivo range verification prior to each treatment delivery.

  20. Potential of a range extender concept for inner city scooters. An alternative to pure electric mobility?; Potenzial eines REX Konzeptes fuer Stadtscooter. Eine Alternative zur rein elektrischen Mobilitaet?

    Energy Technology Data Exchange (ETDEWEB)

    Kirchberger, Roland; Schacht, Hans-Juergen; Eichlseder, Helmut [Technische Univ. Graz (Austria). Inst. fuer Verbrennungskraftmaschinen und Thermodynamik

    2012-11-01

    Nowadays the scooter market class L1e (<50cm{sup 3}, speed limited to 45km/h) is dominated by low-cost two-stroke carburetted engines. With the implementation of the new EURO 3 regulation, obligatory for new type approval by 2014 and for all newly licenced types by 2015, the market will suffer the loss of these low cost vehicles due to the requested durability of exhaust gas after treatment systems. More complex drive units, like lambda controlled 4-stroke engines or 2-stroke engines with direct injection will have to follow. Pure electric scooters pose a further possibility to fill the resulting gap. A significant cost increase is common to all of these approaches. Necessary additional system components will cause the increase for ICE variants, whereas battery costs are responsible for the electric variant. The goal is to find an alternative to be able to comply with the requirements of emission legislation and to keep the product price as low as possible at the same time. A technological comparison of different approaches revealed the serial hybrid variant as most promising. The evaluated system and the derived concept consist of a combination of an electric scooter with a halved battery size (cost reduction) and a Range Extender with the possibility to extend, if necessary, the range to the standard of conventional ICE variants. This alternative is able to offer electro-mobility and therewith local zero emissions without the immanent ''range anxiety'' usually caused by pure electric vehicles [8]. Having defined the system layout as plug-in hybrid-electric vehicle (PHEV) and checked the characteristics of single components in numerous preliminary investigations, a longitudinal backward simulation was carried out. It permits the testing of different operational strategies in combination with a subsequent evaluation of the fuel consumption reduction potential [16]. A packaging analysis could verify the constructive feasibility. Finally, the

  1. Distribution records and extended range of the Sri Lanka Frogmouth Batrachostomus moniliger (Aves: Caprimulgiformes: Podargidae in the Western Ghats: a review from 1862 to 2015

    Directory of Open Access Journals (Sweden)

    Anil Mahabal

    2016-09-01

    Full Text Available The Sri Lanka Frogmouth (or Ceylon Frogmouth Batrachostomus moniliger is an endemic resident bird confined to the evergreen and secondary forests of Sri Lanka and the Western Ghats of India.  The earlier distribution range of the Frogmouth was from the Uttara Kannada District of Karnataka to the southern tip of India and most of Sri Lanka.  Recently, the range has been extended further north to Goa and up to Mumbai in Maharashtra.  A number of observations summarized into 202 distributional records (published reports and records uploaded to eBird basic data set, Oriental Bird Images, and GBIF.org from the years 1862 to 2015 of the Frogmouth have been tabulated with its maps, and reviewed for their state-wise distribution records.  The need of undertaking surveys to fill up the gaps in their distribution range as well as any further northward extension till the culmination of the Western Ghats has been discussed.  It is urged that taxonomical and molecular phylogenetic studies are required to be carried out in different populations of Frogmouths across the entire range

  2. Application of lidar techniques to time-of-flight range imaging.

    Science.gov (United States)

    Whyte, Refael; Streeter, Lee; Cree, Michael J; Dorrington, Adrian A

    2015-11-20

    Amplitude-modulated continuous wave (AMCW) time-of-flight (ToF) range imaging cameras measure distance by illuminating the scene with amplitude-modulated light and measuring the phase difference between the transmitted and reflected modulation envelope. This method of optical range measurement suffers from errors caused by multiple propagation paths, motion, phase wrapping, and nonideal amplitude modulation. In this paper a ToF camera is modified to operate in modes analogous to continuous wave (CW) and stepped frequency continuous wave (SFCW) lidar. In CW operation the velocity of objects can be measured. CW measurement of velocity was linear with true velocity (R2=0.9969). Qualitative analysis of a complex scene confirms that range measured by SFCW is resilient to errors caused by multiple propagation paths, phase wrapping, and nonideal amplitude modulation which plague AMCW operation. In viewing a complicated scene through a translucent sheet, quantitative comparison of AMCW with SFCW demonstrated a reduction in the median error from -1.3  m to -0.06  m with interquartile range of error reduced from 4.0 m to 0.18 m.

  3. Distance based range profile classification techniques for aircraft recognition by radar - a comparison on real radar data

    NARCIS (Netherlands)

    Heiden, R. van der; Groen, F.C.A.

    1995-01-01

    Aircraft identification is essential in any air-defence scenario. Without a robust classification capability no effective threat evaluation can be performed. A prominent aircraft recognition technique is based on the exploitation of a one-dimensional image of a target, a range profile. In this

  4. Range estimation techniques in single-station thunderstorm warning sensors based upon gated, wideband, magnetic direction finder technology

    Science.gov (United States)

    Pifer, Alburt E.; Hiscox, William L.; Cummins, Kenneth L.; Neumann, William T.

    1991-01-01

    Gated, wideband, magnetic direction finders (DFs) were originally designed to measure the bearing of cloud-to-ground lightning relative to the sensor. A recent addition to this device uses proprietary waveform discrimination logic to select return stroke signatures and certain range dependent features in the waveform to provide an estimate of range of flashes within 50 kms. The enhanced ranging techniques are discussed which were designed and developed for use in single station thunderstorm warning sensor. Included are the results of on-going evaluations being conducted under a variety of meteorological and geographic conditions.

  5. Hysteresis and Instability in Some IPRT Sensors Within Temperature Ranges Extending from -196 ^{circ }\\hbox {C} to 150 ^{circ }\\hbox {C}

    Science.gov (United States)

    Rusby, R. L.; Machin, D.

    2017-08-01

    Industrial platinum resistance thermometer (IPRT) sensors or probes suffer from some instability on cycling over significant ranges of temperature and, specifically, from hysteresis in which the resistance tends to follow different paths for increasing temperatures compared with decreasing temperatures. The effect is well known, and cases of quite large hysteresis have been reported in the literature. Therefore, in establishing calibration and measurement capabilities for IPRT calibrations it is important to include an assessment of the performance which can be expected of a `typical good' IPRT and to include this in the overall uncertainty which the laboratory can expect to achieve in such calibrations, even though the effect itself is outside the laboratory's control. This paper presents results which have been obtained in cycling IPRT probes from four sources within various temperature ranges of current interest at NPL, between -196 ^{circ }\\hbox {C} and 150 ^{circ }\\hbox {C}, to see what levels of hysteresis may be expected. The cycles were carried out quite quickly in order to detect the hysteresis before it was mitigated by relaxation effects, but the time dependence was not itself studied. In most cases, hysteresis was {<}0.0025 ^{circ }\\hbox {C} between 0 ^{circ }\\hbox {C} and 100 ^{circ }\\hbox {C}, and {<}0.0035 ^{circ }\\hbox {C} when the range extended down to -80 ^{circ }\\hbox {C} or up to 150 ^{circ }\\hbox {C}. Greater instability occurred when the sensors were cooled to -196 ^{circ }\\hbox {C}.

  6. Range and mission scheduling automation using combined AI and operations research techniques

    Science.gov (United States)

    Arbabi, Mansur; Pfeifer, Michael

    1987-01-01

    Ground-based systems for Satellite Command, Control, and Communications (C3) operations require a method for planning, scheduling and assigning the range resources such as: antenna systems scattered around the world, communications systems, and personnel. The method must accommodate user priorities, last minute changes, maintenance requirements, and exceptions from nominal requirements. Described are computer programs which solve 24 hour scheduling problems, using heuristic algorithms and a real time interactive scheduling process.

  7. Test of hybrid power system for electrical vehicles using a lithium-ion battery pack and a reformed methanol fuel cell range extender

    DEFF Research Database (Denmark)

    Andreasen, Søren Juhl; Ashworth, Leanne; Sahlin, Simon Lennart

    2014-01-01

    monoxide, the HTPEM fuel cell system can efficiently use a liquid methanol/water mixture of 60%/40% by volume, as fuel instead of compressed hydrogen, enabling potentially a higher volumetric energy density. In order to test the performance of such a system, the experimental validation conducted uses......This work presents the proof-of-concept of an electric traction power system with a high temperature polymer electrolyte membrane fuel cell range extender, usable for automotive class electrical vehicles. The hybrid system concept examined, consists of a power system where the primary power...... is delivered by a lithium ion battery pack. In order to increase the run time of the application connected to this battery pack, a high temperature PEM (HTPEM) fuel cell stack acts as an on-board charger able to charge a vehicle during operation as a series hybrid. Because of the high tolerance to carbon...

  8. Power distribution of a co-axial dual-mechanical-port flux-switching permanent magnet machine for fuel-based extended range electric vehicles

    Science.gov (United States)

    Zhou, Lingkang; Hua, Wei; Zhang, Gan

    2017-05-01

    In this paper, power distribution between the inner and outer machines of a co-axial dual-mechanical-port flux-switching permanent magnet (CADMP-FSPM) machine is investigated for fuel-based extended range electric vehicle (ER-EV). Firstly, the topology and operation principle of the CADMP-FSPM machine are introduced, which consist of an inner FSPM machine used for high-speed, an outer FSPM machine for low-speed, and a magnetic isolation ring between them. Then, the magnetic field coupling of the inner and outer FSPM machines is analyzed with more attention paid to the optimization of the isolation ring thickness. Thirdly, the power-dimension (PD) equations of the inner and outer FSPM machines are derived, respectively, and thereafter, the PD equation of the whole CADMP-FSPM machine can be given. Finally, the PD equations are validated by finite element analysis, which supplies the guidance on the design of this type of machines.

  9. Data transmission techniques for short-range optical fiber and wireless communication links

    DEFF Research Database (Denmark)

    Pham, Tien Thang

    The research work described in this thesis is devoted to experimental investigation of techniques for cost-effective high-speed optical communications supporting both wired and wireless services. The main contributions of this thesis have expanded the state-of-the-art in two main areas: high......-speed optical/wireless integration and advanced modulation formats for intensity modulation with direct detection (IM/DD) optical systems. Regarding optical/wireless integration, this thesis focuses on integration of broadband ultra-wide band (UWB) and 60-GHz band wireless systems into optical fiber access......)-compliant gigabit UWB signals and integrate them into baseband wavelength division multiplexingpassive optical networks (WDM-PONs). Performance of UWB signals and other wired/wireless signals in different scenarios including heterogeneous wired and wireless access networks, converged communication and sensing...

  10. Wide-range dynamic strain measurements based on K-BOTDA and frequency-agile technique

    Science.gov (United States)

    Zhou, Dengwang; Dong, Yongkang; Wang, Benzhang; Zhang, Hongying; Lu, Zhiwei

    2017-04-01

    We propose and demonstrate a novel fast Brillouin optical time-domain analysis system using the coefficient K spectrum which is defined as the ratio of phase-shift and gain of Brillouin amplification, where K features linear response, immune to the variation of pump power and a wide measure range. For a 30ns-square pump pulse, the frequency span of K spectrum can reach up to 200MHz. In dynamic strain experiment, a multi-slope assisted K-BOTDA with the measured strain of 5358.3μɛ and the vibration frequency of 6.01Hz and 12.05Hz are demonstrated.

  11. Charging up for the future of plug-in hybrids and range extenders. An exploration of options for increased battery utilisation; Opladen voor de toekomst van plug-in hybrides en range extenders. Een verkenning naar mogelijkheden voor vergroten van het elektrische gebruik

    Energy Technology Data Exchange (ETDEWEB)

    Van Essen, H.; Schroten, A.; Aarnink, S.

    2013-05-15

    If the full potential of plug-in hybrids and electric cars with a range extender is to be usefully exploited, it is important that these vehicles be used in battery mode as much as possible. This means that users' charging and driving behaviour needs to be positively influenced. This can be achieved through suitably designed financial incentives on the part of employers and government, further expansion of battery-charging infrastructure, and transferring knowledge on driving style. Improved driving and charging behaviour will lead to lower effective fuel consumption, reduced CO2 emissions and improved air quality. These are some of the results of this study in which it is examined how the performance of plug-in hybrids and cars with a range extender can be improved. It is the first study to look into the factors governing practical usage of such vehicles and the options available to the various parties to improve that usage. To this end a literature study was carried out and interviews were held with employers, leasing companies, trade associations, government agencies and other parties [Dutch] Om het potentieel van plug-in hybrides en elektrische auto's met een range extender te benutten is het van belang dat deze auto's zoveel mogelijk elektrisch worden gereden. Hiervoor is het nodig om het oplaad- en rijgedrag van de gebruikers positief te beïnvloeden. Dit kan door het geven van slimme financiële prikkels door werkgevers en overheid, het verder uitbreiden van de laadinfrastructuur en kennisoverdracht over rijgedrag. Een verbeterd rij- en laadgedrag zorgt voor een lager brandstofpraktijkverbruik, minder CO2-uitstoot en een betere luchtkwaliteit. Dit staat onder meer in de studie 'Opladen voor de toekomst van plug-in hybrides en range extenders' van CE Delft, waarin op verzoek van de Nederlandse importeurs van Toyota en Opel is onderzocht hoe het elektrisch gebruik kan worden verbeterd. Hierin is voor het eerst gekeken naar de factoren

  12. A comparative analysis between active and passive techniques for underwater 3D reconstruction of close-range objects.

    Science.gov (United States)

    Bianco, Gianfranco; Gallo, Alessandro; Bruno, Fabio; Muzzupappa, Maurizio

    2013-08-20

    In some application fields, such as underwater archaeology or marine biology, there is the need to collect three-dimensional, close-range data from objects that cannot be removed from their site. In particular, 3D imaging techniques are widely employed for close-range acquisitions in underwater environment. In this work we have compared in water two 3D imaging techniques based on active and passive approaches, respectively, and whole-field acquisition. The comparison is performed under poor visibility conditions, produced in the laboratory by suspending different quantities of clay in a water tank. For a fair comparison, a stereo configuration has been adopted for both the techniques, using the same setup, working distance, calibration, and objects. At the moment, the proposed setup is not suitable for real world applications, but it allowed us to conduct a preliminary analysis on the performances of the two techniques and to understand their capability to acquire 3D points in presence of turbidity. The performances have been evaluated in terms of accuracy and density of the acquired 3D points. Our results can be used as a reference for further comparisons in the analysis of other 3D techniques and algorithms.

  13. A Comparative Analysis between Active and Passive Techniques for Underwater 3D Reconstruction of Close-Range Objects

    Directory of Open Access Journals (Sweden)

    Maurizio Muzzupappa

    2013-08-01

    Full Text Available In some application fields, such as underwater archaeology or marine biology, there is the need to collect three-dimensional, close-range data from objects that cannot be removed from their site. In particular, 3D imaging techniques are widely employed for close-range acquisitions in underwater environment. In this work we have compared in water two 3D imaging techniques based on active and passive approaches, respectively, and whole-field acquisition. The comparison is performed under poor visibility conditions, produced in the laboratory by suspending different quantities of clay in a water tank. For a fair comparison, a stereo configuration has been adopted for both the techniques, using the same setup, working distance, calibration, and objects. At the moment, the proposed setup is not suitable for real world applications, but it allowed us to conduct a preliminary analysis on the performances of the two techniques and to understand their capability to acquire 3D points in presence of turbidity. The performances have been evaluated in terms of accuracy and density of the acquired 3D points. Our results can be used as a reference for further comparisons in the analysis of other 3D techniques and algorithms.

  14. Reconfigurable Resonant Regulating Rectifier With Primary Equalization for Extended Coupling- and Loading-Range in Bio-Implant Wireless Power Transfer.

    Science.gov (United States)

    Li, Xing; Meng, Xiaodong; Tsui, Chi-Ying; Ki, Wing-Hung

    2015-12-01

    Wireless power transfer using reconfigurable resonant regulating (R(3)) rectification suffers from limited range in accommodating varying coupling and loading conditions. A primary-assisted regulation principle is proposed to mitigate these limitations, of which the amplitude of the rectifier input voltage on the secondary side is regulated by accordingly adjusting the voltage amplitude Veq on the primary side. A novel current-sensing method and calibration scheme track Veq on the primary side. A ramp generator simultaneously provides three clock signals for different modules. Both the primary equalizer and the R(3) rectifier are implemented as custom integrated circuits fabricated in a 0.35 μm CMOS process, with the global control implemented in FPGA. Measurements show that with the primary equalizer, the workable coupling and loading ranges are extended by 250% at 120 mW load and 300% at 1.2 cm coil distance compared to the same system without the primary equalizer. A maximum rectifier efficiency of 92.5% and a total system efficiency of 62.4% are demonstrated.

  15. The effect of sacro occipital technique category II blocking on spinal ranges of motion: a case series.

    Science.gov (United States)

    Hochman, Jerry I

    2005-01-01

    To describe changes in lumbar and cervical range of motion measurements after supine pelvic blocking as used in Sacro Occipital Technique (SOT). Five subjects with sacroiliac distortion and instability were recruited and selected for SOT. Cervical and lumbar ranges of motion were measured before and after category II blocking procedures used to change pelvic mechanics. Pre- and post-measurements were taken by a blinded assessor using a Zebris ultrasonic motion detector. Changes were found in the lumbar spine only. Increased ranges of lumbar motion occurred in all planes except extension (21%-57%). Supine pelvic blocking as used in SOT affected lumbar ranges of motion in these 5 cases. This may indicate that functional change in the pelvis results in changes in lumbar motion, especially lumbar flexion. Larger data sets are needed for further study.

  16. Application of ranging technique of radar level meter for draft survey

    Directory of Open Access Journals (Sweden)

    SHEN Yijun

    2017-12-01

    Full Text Available [Objectives] This paper aims to solve the problems of the high subjectivity and low accuracy and efficiency of draft surveying relying on human visual inspection.[Methods] Radar-level oil and liquid measurement technology products are widely used in the petrochemical industry. A device is developed that uses radar to survey the draft of a boat, designed with data series optimization formulae to ensure that the data results are true and correct. At the same time, a test is designed to prove the accuracy of the results.[Results] According to the conditions of the ship,the device is composed of a radar sensor, triangular bracket and display,and is put to use in the test.[Conclusions] With 15 vessels as the research objects,the comparison experiment shows a difference in range between 0.001-0.022 meters, with an average difference rate of 0.028%, which meets the requirements for ship draft survey accuracy.

  17. Novel technique for evaluation of knee function continuously through the range of flexion.

    Science.gov (United States)

    Bell, Kevin M; Arilla, Fabio V; Rahnemai-Azar, Ata A; Fu, Freddie H; Musahl, Volker; Debski, Richard E

    2015-10-15

    Previous research has utilized robots to examine joint kinematics and in situ forces in response to loads applied at discrete flexion angles (static method). Recently, studies have applied loads continuously throughout flexion (continuous flexion method). However, the joint kinematics resulting from each of these methods have not been directly compared. Therefore, the objective of this study was to utilize a robotic testing system to compare kinematics and in situ forces of porcine knees in response to 89 N of anterior tibial load and 4 Nm of internal tibial torque between the static method (loads applied at 30°, 45°, 60°, and 75° of flexion) and the continuous flexion method (measured continuously from 30-75° of flexion) for both the anterior cruciate ligament (ACL) intact and ACL deficient (ACLD) knees. When anterior tibial load was applied the average differences in anterior tibial translation between the two methods for the intact state was 0.5±0.0 mm and for the ACLD state was 0.3±0.2 mm. The difference in the in situ forces in the ACL was 1.6±0.9 N. When internal tibial torque was applied the average differences in the resultant internal tibial rotation for the intact state was 0.9±0.4° and for the ACLD state was 1.0±0.5°. The difference in the in situ forces in the ACL was 3.3±2.0 N. Both methods are equally efficient in detecting significant differences (p<0.05) between intact and ACL deficient knee states. The continuous flexion method was also shown to be more efficient than the static method and provides continuous data on knee function throughout the range of motion. Copyright © 2015 Elsevier Ltd. All rights reserved.

  18. Extended release promethazine HCl using acrylic polymers by freeze-drying and spray-drying techniques: formulation considerations

    Directory of Open Access Journals (Sweden)

    Ruchi Tiwari

    2009-12-01

    Full Text Available The present study investigated a novel extended release system of promethazine hydrochloride (PHC with acrylic polymers Eudragit RL100 and Eudragit S100 in different weight ratios (1:1 and 1: 5, and in combination (0.5+1.5, using freeze-drying and spray-drying techniques. Solid dispersions were characterized by Fourier-transformed infrared spectroscopy (FT-IR, differential scanning calorimetry (DSC, Powder X-ray diffractometry (PXRD, Nuclear magnetic resonance (NMR, Scanning electron microscopy (SEM, as well as solubility and in vitro dissolution studies in 0.1 N HCl (pH 1.2, double-distilled water and phosphate buffer (pH 7.4. Adsorption tests from drug solution to solid polymers were also performed. A selected solid dispersion system was developed into capsule dosage form and evaluated for in vitro dissolution studies. The progressive disappearance of drug peaks in thermotropic profiles of spray-dried dispersions were related to increasing amount of polymers, while SEM studies suggested homogenous dispersion of drug in polymer. Eudragit RL100 had a greater adsorptive capacity than Eudragit S100, and thus its combination in (0.5+1.5 for S100 and RL 100 exhibited a higher dissolution rate with 97.14% drug release for twelve hours. Among different formulations, capsules prepared by combination of acrylic polymers using spray-drying (1:0.5 + 1.5 displayed extended release of drug for twelve hours with 96.87% release followed by zero order kinetics (r²= 0.9986.O presente trabalho compreendeu estudo de um novo sistema de liberação prolongada de cloridrato de prometazina (PHC com polímeros acrílicos Eudragit RL100 e Eudragit S100 em diferentes proporções em massa (1:1 e 1:5 e em combinação (0,5+1,5, utilizando técnicas de liofilização e de secagem por aspersão As dispersões sólidas foram caracterizadas por espectrofotometria no infravermelho por transformada de Fourier (FT-IR, calorimetria diferencial de varredura (DSC, difratometria

  19. Unmanned Aerial Vehicle (UAV) Dynamic-Tracking Directional Wireless Antennas for Low Powered Applications that Require Reliable Extended Range Operations in Time Critical Scenarios

    Energy Technology Data Exchange (ETDEWEB)

    Scott G. Bauer; Matthew O. Anderson; James R. Hanneman

    2005-10-01

    The proven value of DOD Unmanned Aerial Vehicles (UAVs) will ultimately transition to National and Homeland Security missions that require real-time aerial surveillance, situation awareness, force protection, and sensor placement. Public services first responders who routinely risk personal safety to assess and report a situation for emergency actions will likely be the first to benefit from these new unmanned technologies. ‘Packable’ or ‘Portable’ small class UAVs will be particularly useful to the first responder. They require the least amount of training, no fixed infrastructure, and are capable of being launched and recovered from the point of emergency. All UAVs require wireless communication technologies for real- time applications. Typically on a small UAV, a low bandwidth telemetry link is required for command and control (C2), and systems health monitoring. If the UAV is equipped with a real-time Electro-Optical or Infrared (EO/Ir) video camera payload, a dedicated high bandwidth analog/digital link is usually required for reliable high-resolution imagery. In most cases, both the wireless telemetry and real-time video links will be integrated into the UAV with unity gain omni-directional antennas. With limited on-board power and payload capacity, a small UAV will be limited with the amount of radio-frequency (RF) energy it transmits to the users. Therefore, ‘packable’ and ‘portable’ UAVs will have limited useful operational ranges for first responders. This paper will discuss the limitations of small UAV wireless communications. The discussion will present an approach of utilizing a dynamic ground based real-time tracking high gain directional antenna to provide extend range stand-off operation, potential RF channel reuse, and assured telemetry and data communications from low-powered UAV deployed wireless assets.

  20. Power distribution of a co-axial dual-mechanical-port flux-switching permanent magnet machine for fuel-based extended range electric vehicles

    Directory of Open Access Journals (Sweden)

    Lingkang Zhou

    2017-05-01

    Full Text Available In this paper, power distribution between the inner and outer machines of a co-axial dual-mechanical-port flux-switching permanent magnet (CADMP-FSPM machine is investigated for fuel-based extended range electric vehicle (ER-EV. Firstly, the topology and operation principle of the CADMP-FSPM machine are introduced, which consist of an inner FSPM machine used for high-speed, an outer FSPM machine for low-speed, and a magnetic isolation ring between them. Then, the magnetic field coupling of the inner and outer FSPM machines is analyzed with more attention paid to the optimization of the isolation ring thickness. Thirdly, the power-dimension (PD equations of the inner and outer FSPM machines are derived, respectively, and thereafter, the PD equation of the whole CADMP-FSPM machine can be given. Finally, the PD equations are validated by finite element analysis, which supplies the guidance on the design of this type of machines.

  1. Extending the Collection Duration of Breath Samples for Enteric Methane Emission Estimation Using the SF6 Tracer Technique

    OpenAIRE

    John Koolaard; Grant Taylor; German Molano; Sarah MacLean; Edgar Sandoval; Roberto Gratton; Paula Juliarena; César Pinares-Patiño; José Gere; Karen Williams

    2012-01-01

    Simple Summary Extended sample collection for the SF6 tracer technique is desirable for extensive grazing systems. Breath samples from eight cows were collected while lucerne silage was fed to achieve fixed intakes among the cows. Samples were collected over a 10-day period, using either apparatuses used in New Zealand (NZL) or Argentina (ARG), and either daily, over two consecutive 5-day periods or over a 10-day period (in duplicate). The NZL system had a greater sampling success and more co...

  2. Autonomous Target Ranging Techniques

    DEFF Research Database (Denmark)

    Jørgensen, Peter Siegbjørn; Jørgensen, John Leif; Denver, Troelz

    2003-01-01

    For the deep space asteroid mission, Bering, the main goal is the detection and tracking of near Earth objects (NEOs) and asteroids. One of the key science instruments is the 0.3-m telescope used for imaging and tracking of the detected asteroidal objects. For efficient use of the observation tim...

  3. Comparison of an indirect tri-planar myofascial release (MFR) technique and a hot pack for increasing range of motion.

    Science.gov (United States)

    Kain, Jay; Martorello, Laura; Swanson, Edward; Sego, Sandra

    2011-01-01

    The purpose of the randomized clinical study was to scientifically assess which intervention increases passive range of motion most effectively: the indirect tri-planar myofascial release (MFR) technique or the application of hot packs for gleno-humeral joint flexion, extension, and abduction. A total of 31 participants from a sample of convenience were randomly assigned to examine whether or not MFR was as effective in increasing range of motion as hot packs. The sample consisted of students at American International College. Students were randomly assigned to two groups: hot pack application (N=13) or MFR technique (N=18). The independent variable was the intervention, either the tri-planar MFR technique or the hot pack application. Group one received the indirect tri-planar MFR technique once for 3min. Group two received one hot pack application for 20min. The dependent variables, passive gleno-humeral shoulder range of motion in shoulder flexion, shoulder extension, and shoulder abduction, were taken pre- and post-intervention for both groups. Data was analyzed through the use of a two-way factorial design with mixed-factors ANOVA. Prior to conducting the study, inter-rater reliability was established using three testers for goniometric measures. A 2 (type of intervention: hot packs or MFR) by 2 (pre-test or post-test) mixed-factors ANOVA was calculated. Significant increases in range of motion were found for flexion, extension and abduction when comparing pre-test scores to post-test scores. The results of the ANOVA showed that for passive range of motion no differences were found for flexion, extension and abduction between the effectiveness of hot packs and MFR. For each of the dependent variables measured, MFR was shown to be as effective as hot packs in increasing range of motion, supporting the hypothesis. Since there was no significant difference between the types of intervention, both the hot pack application and the MFR technique were found to be

  4. Secondary neutron spectrum from 250-MeV passively scattered proton therapy: Measurement with an extended-range Bonner sphere system

    Energy Technology Data Exchange (ETDEWEB)

    Howell, Rebecca M., E-mail: rhowell@mdanderson.org [Department of Radiation Physics, The University of Texas MD Anderson Cancer Center, Houston, Texas 77030 (United States); Burgett, E. A. [Department of Nuclear Engineering, Idaho State University, Pocatello, Idaho 83201 (United States)

    2014-09-15

    Purpose: Secondary neutrons are an unavoidable consequence of proton therapy. While the neutron dose is low compared to the primary proton dose, its presence and contribution to the patient dose is nonetheless important. The most detailed information on neutrons includes an evaluation of the neutron spectrum. However, the vast majority of the literature that has reported secondary neutron spectra in proton therapy is based on computational methods rather than measurements. This is largely due to the inherent limitations in the majority of neutron detectors, which are either not suitable for spectral measurements or have limited response at energies greater than 20 MeV. Therefore, the primary objective of the present study was to measure a secondary neutron spectrum from a proton therapy beam using a spectrometer that is sensitive to neutron energies over the entire neutron energy spectrum. Methods: The authors measured the secondary neutron spectrum from a 250-MeV passively scattered proton beam in air at a distance of 100 cm laterally from isocenter using an extended-range Bonner sphere (ERBS) measurement system. Ambient dose equivalent H*(10) was calculated using measured fluence and fluence-to-ambient dose equivalent conversion coefficients. Results: The neutron fluence spectrum had a high-energy direct neutron peak, an evaporation peak, a thermal peak, and an intermediate energy continuum between the thermal and evaporation peaks. The H*(10) was dominated by the neutrons in the evaporation peak because of both their high abundance and the large quality conversion coefficients in that energy interval. The H*(10) 100 cm laterally from isocenter was 1.6 mSv per proton Gy (to isocenter). Approximately 35% of the dose equivalent was from neutrons with energies ≥20 MeV. Conclusions: The authors measured a neutron spectrum for external neutrons generated by a 250-MeV proton beam using an ERBS measurement system that was sensitive to neutrons over the entire

  5. Secondary neutron spectrum from 250-MeV passively scattered proton therapy: measurement with an extended-range Bonner sphere system.

    Science.gov (United States)

    Howell, Rebecca M; Burgett, E A

    2014-09-01

    Secondary neutrons are an unavoidable consequence of proton therapy. While the neutron dose is low compared to the primary proton dose, its presence and contribution to the patient dose is nonetheless important. The most detailed information on neutrons includes an evaluation of the neutron spectrum. However, the vast majority of the literature that has reported secondary neutron spectra in proton therapy is based on computational methods rather than measurements. This is largely due to the inherent limitations in the majority of neutron detectors, which are either not suitable for spectral measurements or have limited response at energies greater than 20 MeV. Therefore, the primary objective of the present study was to measure a secondary neutron spectrum from a proton therapy beam using a spectrometer that is sensitive to neutron energies over the entire neutron energy spectrum. The authors measured the secondary neutron spectrum from a 250-MeV passively scattered proton beam in air at a distance of 100 cm laterally from isocenter using an extended-range Bonner sphere (ERBS) measurement system. Ambient dose equivalent H*(10) was calculated using measured fluence and fluence-to-ambient dose equivalent conversion coefficients. The neutron fluence spectrum had a high-energy direct neutron peak, an evaporation peak, a thermal peak, and an intermediate energy continuum between the thermal and evaporation peaks. The H*(10) was dominated by the neutrons in the evaporation peak because of both their high abundance and the large quality conversion coefficients in that energy interval. The H*(10) 100 cm laterally from isocenter was 1.6 mSv per proton Gy (to isocenter). Approximately 35% of the dose equivalent was from neutrons with energies ≥20 MeV. The authors measured a neutron spectrum for external neutrons generated by a 250-MeV proton beam using an ERBS measurement system that was sensitive to neutrons over the entire energy range being measured, i.e., thermal to

  6. Depth profiling of residual activity of ^{237}U fragments as a range verification technique for ^{238}U primary ion beam

    Directory of Open Access Journals (Sweden)

    I. Strašík

    2012-07-01

    Full Text Available Experimental and simulation data concerning fragmentation of ^{238}U ion beam in aluminum, copper, and stainless-steel targets with the initial energy 500 and 950  MeV/u are collected in the paper. A range-verification technique based on depth profiling of residual activity is presented. The irradiated targets were constructed in the stacked-foil geometry and analyzed using gamma-ray spectroscopy. One of the purposes of these experiments was depth profiling of residual activity of induced nuclides and projectile fragments. Among the projectile fragments, special attention is paid to the ^{237}U isotope that has a range very close to the range of the primary ^{238}U ions. Therefore, the depth profiling of the ^{237}U isotope can be utilized for experimental verification of the ^{238}U primary-beam range, which is demonstrated and discussed in the paper. The experimental data are compared with computer simulations by FLUKA, SRIM, and ATIMA, as well as with complementary experiments.

  7. Depth profiling of residual activity of U237 fragments as a range verification technique for U238 primary ion beam

    Science.gov (United States)

    Strašík, I.; Chetvertkova, V.; Mustafin, E.; Pavlovič, M.; Belousov, A.

    2012-07-01

    Experimental and simulation data concerning fragmentation of U238 ion beam in aluminum, copper, and stainless-steel targets with the initial energy 500 and 950MeV/u are collected in the paper. A range-verification technique based on depth profiling of residual activity is presented. The irradiated targets were constructed in the stacked-foil geometry and analyzed using gamma-ray spectroscopy. One of the purposes of these experiments was depth profiling of residual activity of induced nuclides and projectile fragments. Among the projectile fragments, special attention is paid to the U237 isotope that has a range very close to the range of the primary U238 ions. Therefore, the depth profiling of the U237 isotope can be utilized for experimental verification of the U238 primary-beam range, which is demonstrated and discussed in the paper. The experimental data are compared with computer simulations by FLUKA, SRIM, and ATIMA, as well as with complementary experiments.

  8. Quantitative estimation of climatic parameters from vegetation data in North America by the mutual climatic range technique

    Science.gov (United States)

    Anderson, Katherine H.; Bartlein, Patrick J.; Strickland, Laura E.; Pelltier, Richard T.; Thompson, Robert S.; Shafer, Sarah L.

    2012-01-01

    The mutual climatic range (MCR) technique is perhaps the most widely used method for estimating past climatic parameters from fossil assemblages, largely because it can be conducted on a simple list of the taxa present in an assemblage. When applied to plant macrofossil data, this unweighted approach (MCRun) will frequently identify a large range for a given climatic parameter where the species in an assemblage can theoretically live together. To narrow this range, we devised a new weighted approach (MCRwt) that employs information from the modern relations between climatic parameters and plant distributions to lessen the influence of the "tails" of the distributions of the climatic data associated with the taxa in an assemblage. To assess the performance of the MCR approaches, we applied them to a set of modern climatic data and plant distributions on a 25-km grid for North America, and compared observed and estimated climatic values for each grid point. In general, MCRwt was superior to MCRun in providing smaller anomalies, less bias, and better correlations between observed and estimated values. However, by the same measures, the results of Modern Analog Technique (MAT) approaches were superior to MCRwt. Although this might be reason to favor MAT approaches, they are based on assumptions that may not be valid for paleoclimatic reconstructions, including that: 1) the absence of a taxon from a fossil sample is meaningful, 2) plant associations were largely unaffected by past changes in either levels of atmospheric carbon dioxide or in the seasonal distributions of solar radiation, and 3) plant associations of the past are adequately represented on the modern landscape. To illustrate the application of these MCR and MAT approaches to paleoclimatic reconstructions, we applied them to a Pleistocene paleobotanical assemblage from the western United States. From our examinations of the estimates of modern and past climates from vegetation assemblages, we conclude that

  9. Shoulder 3D range of motion and humerus rotation in two volleyball spike techniques: injury prevention and performance.

    Science.gov (United States)

    Seminati, Elena; Marzari, Alessandra; Vacondio, Oreste; Minetti, Alberto E

    2015-06-01

    Repetitive stresses and movements on the shoulder in the volleyball spike expose this joint to overuse injuries, bringing athletes to a career threatening injury. Assuming that specific spike techniques play an important role in injury risk, we compared the kinematic of the traditional (TT) and the alternative (AT) techniques in 21 elite athletes, evaluating their safety with respect to performance. Glenohumeral joint was set as the centre of an imaginary sphere, intersected by the distal end of the humerus at different angles. Shoulder range of motion and angular velocities were calculated and compared to the joint limits. Ball speed and jump height were also assessed. Results indicated the trajectory of the humerus to be different for the TT, with maximal flexion of the shoulder reduced by 10 degrees, and horizontal abduction 15 degrees higher. No difference was found for external rotation angles, while axial rotation velocities were significantly higher in AT, with a 5% higher ball speed. Results suggest AT as a potential preventive solution to shoulder chronic pathologies, reducing shoulder flexion during spiking. The proposed method allows visualisation of risks associated with different overhead manoeuvres, by depicting humerus angles and velocities with respect to joint limits in the same 3D space.

  10. Highly Sensitive and Wide-Dynamic-Range Multichannel Optical-Fiber pH Sensor Based on PWM Technique.

    Science.gov (United States)

    Khan, Md Rajibur Rahaman; Kang, Shin-Won

    2016-11-09

    In this study, we propose a highly sensitive multichannel pH sensor that is based on an optical-fiber pulse width modulation (PWM) technique. According to the optical-fiber PWM method, the received sensing signal's pulse width changes when the optical-fiber pH sensing-element of the array comes into contact with pH buffer solutions. The proposed optical-fiber PWM pH-sensing system offers a linear sensing response over a wide range of pH values from 2 to 12, with a high pH-sensing ability. The sensitivity of the proposed pH sensor is 0.46 µs/pH, and the correlation coefficient R² is approximately 0.997. Additional advantages of the proposed optical-fiber PWM pH sensor include a short/fast response-time of about 8 s, good reproducibility properties with a relative standard deviation (RSD) of about 0.019, easy fabrication, low cost, small size, reusability of the optical-fiber sensing-element, and the capability of remote sensing. Finally, the performance of the proposed PWM pH sensor was compared with that of potentiometric, optical-fiber modal interferometer, and optical-fiber Fabry-Perot interferometer pH sensors with respect to dynamic range width, linearity as well as response and recovery times. We observed that the proposed sensing systems have better sensing abilities than the above-mentioned pH sensors.

  11. A Technique for Mitigating Thermal Stress and Extending Life Cycle of Power Electronic Converters Used for Wind Turbines

    Directory of Open Access Journals (Sweden)

    Canras Batunlu

    2015-11-01

    Full Text Available Over the last two decades, various models have been developed to assess and improve the reliability of power electronic conversion systems (PECs with a focus on those used for wind turbines. However, only few studies have dealt with mitigating the PECs thermo-mechanical effects on their reliability taking into account variations in wind characteristics. This work critically investigates this issue and attempts to offer a mitigating technique by, first, developing realistic full scale (FS and partial scale (PS induction generator models combined with two level back-to-back PECs. Subsequently, deriving a driving algorithm, which reduces PEC’s operating temperature by controlling its switching patterns. The developed switching procedure ensures minimum temperature fluctuations by adapting the variable DC link and system’s frequency of operation. It was found for both FS and PS topologies, that the generator side converters have higher mean junction temperatures where the grid side ones have more fluctuations on their thermal profile. The FS and PS cycling temperatures were reduced by 12 °C and 5 °C, respectively. Moreover, this led to a significant improvement in stress; approximately 27 MPa stress reduction for the FS induction generator PEC.

  12. Age Determination by Back Length for African Savanna Elephants: Extending Age Assessment Techniques for Aerial-Based Surveys

    Science.gov (United States)

    Trimble, Morgan J.; van Aarde, Rudi J.; Ferreira, Sam M.; Nørgaard, Camilla F.; Fourie, Johan; Lee, Phyllis C.; Moss, Cynthia J.

    2011-01-01

    Determining the age of individuals in a population can lead to a better understanding of population dynamics through age structure analysis and estimation of age-specific fecundity and survival rates. Shoulder height has been used to accurately assign age to free-ranging African savanna elephants. However, back length may provide an analog measurable in aerial-based surveys. We assessed the relationship between back length and age for known-age elephants in Amboseli National Park, Kenya, and Addo Elephant National Park, South Africa. We also compared age- and sex-specific back lengths between these populations and compared adult female back lengths across 11 widely dispersed populations in five African countries. Sex-specific Von Bertalanffy growth curves provided a good fit to the back length data of known-age individuals. Based on back length, accurate ages could be assigned relatively precisely for females up to 23 years of age and males up to 17. The female back length curve allowed more precise age assignment to older females than the curve for shoulder height does, probably because of divergence between the respective growth curves. However, this did not appear to be the case for males, but the sample of known-age males was limited to ≤27 years. Age- and sex-specific back lengths were similar in Amboseli National Park and Addo Elephant National Park. Furthermore, while adult female back lengths in the three Zambian populations were generally shorter than in other populations, back lengths in the remaining eight populations did not differ significantly, in support of claims that growth patterns of African savanna elephants are similar over wide geographic regions. Thus, the growth curves presented here should allow researchers to use aerial-based surveys to assign ages to elephants with greater precision than previously possible and, therefore, to estimate population variables. PMID:22028925

  13. Age determination by back length for African savanna elephants: extending age assessment techniques for aerial-based surveys.

    Science.gov (United States)

    Trimble, Morgan J; van Aarde, Rudi J; Ferreira, Sam M; Nørgaard, Camilla F; Fourie, Johan; Lee, Phyllis C; Moss, Cynthia J

    2011-01-01

    Determining the age of individuals in a population can lead to a better understanding of population dynamics through age structure analysis and estimation of age-specific fecundity and survival rates. Shoulder height has been used to accurately assign age to free-ranging African savanna elephants. However, back length may provide an analog measurable in aerial-based surveys. We assessed the relationship between back length and age for known-age elephants in Amboseli National Park, Kenya, and Addo Elephant National Park, South Africa. We also compared age- and sex-specific back lengths between these populations and compared adult female back lengths across 11 widely dispersed populations in five African countries. Sex-specific Von Bertalanffy growth curves provided a good fit to the back length data of known-age individuals. Based on back length, accurate ages could be assigned relatively precisely for females up to 23 years of age and males up to 17. The female back length curve allowed more precise age assignment to older females than the curve for shoulder height does, probably because of divergence between the respective growth curves. However, this did not appear to be the case for males, but the sample of known-age males was limited to ≤27 years. Age- and sex-specific back lengths were similar in Amboseli National Park and Addo Elephant National Park. Furthermore, while adult female back lengths in the three Zambian populations were generally shorter than in other populations, back lengths in the remaining eight populations did not differ significantly, in support of claims that growth patterns of African savanna elephants are similar over wide geographic regions. Thus, the growth curves presented here should allow researchers to use aerial-based surveys to assign ages to elephants with greater precision than previously possible and, therefore, to estimate population variables.

  14. Age determination by back length for African savanna elephants: extending age assessment techniques for aerial-based surveys.

    Directory of Open Access Journals (Sweden)

    Morgan J Trimble

    Full Text Available Determining the age of individuals in a population can lead to a better understanding of population dynamics through age structure analysis and estimation of age-specific fecundity and survival rates. Shoulder height has been used to accurately assign age to free-ranging African savanna elephants. However, back length may provide an analog measurable in aerial-based surveys. We assessed the relationship between back length and age for known-age elephants in Amboseli National Park, Kenya, and Addo Elephant National Park, South Africa. We also compared age- and sex-specific back lengths between these populations and compared adult female back lengths across 11 widely dispersed populations in five African countries. Sex-specific Von Bertalanffy growth curves provided a good fit to the back length data of known-age individuals. Based on back length, accurate ages could be assigned relatively precisely for females up to 23 years of age and males up to 17. The female back length curve allowed more precise age assignment to older females than the curve for shoulder height does, probably because of divergence between the respective growth curves. However, this did not appear to be the case for males, but the sample of known-age males was limited to ≤27 years. Age- and sex-specific back lengths were similar in Amboseli National Park and Addo Elephant National Park. Furthermore, while adult female back lengths in the three Zambian populations were generally shorter than in other populations, back lengths in the remaining eight populations did not differ significantly, in support of claims that growth patterns of African savanna elephants are similar over wide geographic regions. Thus, the growth curves presented here should allow researchers to use aerial-based surveys to assign ages to elephants with greater precision than previously possible and, therefore, to estimate population variables.

  15. When opposites repel: from metastability to extended chiral spin textures in spin ice with short-range topological-defect interactions

    OpenAIRE

    Udagawa, Masafumi; Jaubert, Ludovic D.C.; Castelnovo, Claudio; Moessner, Roderich

    2016-01-01

    We study the interplay of topological bottlenecks and energetic barriers to equilibration in a Coulomb spin liquid where a short-range energetic coupling between defects charged under an emergent gauge field supplements their entropic long-range Coulomb interaction. This work is motivated by the prevalence of memory effects observed across a wide range of geometrically frustrated magnetic materials, possibly including the spontaneous Hall effect observed in Pr2Ir2O7. Our model is canonical sp...

  16. Spray drying as a fast and simple technique for the preparation of extended release dipyridamole (DYP) microparticles in a fixed dose combination (FDC) product with aspirin.

    Science.gov (United States)

    Hamishehkar, H; Valizadeh, H; Alasty, P; Monajjemzadeh, F

    2014-02-01

    Recent advances have proven that the combinational therapy of extended release dipyridamole (DYP) and fast release aspirin (ASP) can improve clinical indices of heart failure in several vascular disorders. Although pharmaceutical industries always supported fast, simple and cost saving techniques in their productions, there is no simple reported method available for this purpose. The aim of this study was to check the possibility of preparing a FDC product, containing individual dosage units of extended release DYP microparticles and fast release ASP, using the spray-drying technique as a practice compatible with pharmaceutical industries. Solid dispersions of DYP in different polymeric substances (ethyl cellulose, carnauba wax, and Eudragit PO 100), were prepared using the spray-drying method. The physicochemical properties and structure of the prepared microparticles were analyzed using different techniques, such as the particle size analyzer (PSA), differential scanning calorimetry (DSC), scanning electron microscopy (SEM), X ray diffraction (XRD), and USP dissolution tester. ASP tablets were prepared individually and tested according to pharmacopeia. Results showed that prepared microparticles measured about 2.3 µm in size. Statistical analysis of the release data revealed that there is no significant difference in the mean release amount of the selected formulation compared to the innovative brand (Aggrenox®). Findings proposed a new formulation (F7) as an alternative to innovative brand and proved spray drying as a practice compatible with pharmaceutical industries and as a successful method for sustaining the DYP release rate from prepared microparticles in a FDC dosage form. © Georg Thieme Verlag KG Stuttgart · New York.

  17. Experimental integrative muscular movement technique enhances cervical range of motion in patients with chronic neck pain: a pilot study.

    Science.gov (United States)

    Rohe, Benjamin G; Carter, Ronald; Thompson, William R; Duncan, Randall L; Cooper, Carlton R

    2015-04-01

    Neck pain presents a tremendous physical and financial burden. This study compared the efficacy of the complementary and alternative medical treatments of integrative muscular movement technique (IMMT) and Swedish massage on neck pain in women of occupation age, the largest demographic group with neck pain. A total of 38 women were assigned to IMMT (n=28) or Swedish massage (n=10) in a blinded manner. Both groups received eight 30-minute treatments over 4 weeks. Cervical range of motion (ROM) in flexion, extension, sidebending, and rotation was measured before and after treatment. Each patient's pain was assessed by using an analogue pain scale of 0-10. Compared with the Swedish massage group, patients receiving IMMT experienced a significant increase in ROM in cervical flexion (ppain for IMMT was -1.75 units compared with -0.3 units for Swedish massage (pneck pain may lead to decreased pain and increased cervical ROM. These positive effects of the IMMT intervention may have a role in enhancing functional outcomes in patients with neck pain.

  18. OvidSP Medline-to-PubMed search filter translation: a methodology for extending search filter range to include PubMed's unique content.

    Science.gov (United States)

    Damarell, Raechel A; Tieman, Jennifer J; Sladek, Ruth M

    2013-07-02

    PubMed translations of OvidSP Medline search filters offer searchers improved ease of access. They may also facilitate access to PubMed's unique content, including citations for the most recently published biomedical evidence. Retrieving this content requires a search strategy comprising natural language terms ('textwords'), rather than Medical Subject Headings (MeSH). We describe a reproducible methodology that uses a validated PubMed search filter translation to create a textword-only strategy to extend retrieval to PubMed's unique heart failure literature. We translated an OvidSP Medline heart failure search filter for PubMed and established version equivalence in terms of indexed literature retrieval. The PubMed version was then run within PubMed to identify citations retrieved by the filter's MeSH terms (Heart failure, Left ventricular dysfunction, and Cardiomyopathy). It was then rerun with the same MeSH terms restricted to searching on title and abstract fields (i.e. as 'textwords'). Citations retrieved by the MeSH search but not the textword search were isolated. Frequency analysis of their titles/abstracts identified natural language alternatives for those MeSH terms that performed less effectively as textwords. These terms were tested in combination to determine the best performing search string for reclaiming this 'lost set'. This string, restricted to searching on PubMed's unique content, was then combined with the validated PubMed translation to extend the filter's performance in this database. The PubMed heart failure filter retrieved 6829 citations. Of these, 834 (12%) failed to be retrieved when MeSH terms were converted to textwords. Frequency analysis of the 834 citations identified five high frequency natural language alternatives that could improve retrieval of this set (cardiac failure, cardiac resynchronization, left ventricular systolic dysfunction, left ventricular diastolic dysfunction, and LV dysfunction). Together these terms reclaimed

  19. Experimental techniques for characterising water in wood covering the range from dry to fully water-saturated

    DEFF Research Database (Denmark)

    Thybring, Emil Engelund; Kymäläinen, Maija; Rautkari, Lauri

    2018-01-01

    Water plays a central role in wood research, since it affects all material properties relevant to the performance of wood materials. Therefore, experimental techniques for characterising water within wood are an essential part of nearly all scientific investigations of wood materials. This review...... focuses on selected experimental techniques that can give deeper insights into various aspects of water in wood in the entire moisture domain from dry to fully water-saturated. These techniques fall into three broad categories: (1) gravimetric techniques that determine how much water is absorbed, (2......) fibre saturation techniques that determine the amount of water within cell walls, and (3) spectroscopic techniques that provide insights into chemical wood–water interactions as well as yield information on water distribution in the macro-void wood structure. For all techniques, the general measurement...

  20. Cross-biome transplants of plant litter show decomposition models extend to a broader climatic range but lose predictability at the decadal time scale

    Science.gov (United States)

    William S. Currie; Mark E. Harmon; Ingrid C. Burke; Stephen C. Hart; William J. Parton; Whendee L. Silver

    2009-01-01

    We analyzed results from 10-year long field incubations of foliar and fine root litter from the Long-term lntersite Decomposition Experiment Team (LIDET) study. We tested whether a variety of climate and litter quality variables could be used to develop regression models of decomposition parameters across wide ranges in litter quality and climate and whether these...

  1. The extending of ranges of some bird species at the north-eastern border of their distribution due to intra-century climate changes

    Directory of Open Access Journals (Sweden)

    Oleg V. Glushenkov

    2017-10-01

    Full Text Available The paper presents an overview of the phenomenon of range expanding of birds located at the northeastern limit of their range. The study area is located in the Volga-Kama Krai in the Chuvash Republic, adjacent to the River Volga. It is situated northwards and southwards of 56° N, and westwards and eastwards of 49° E, in a band of about 400 km. The problem is considered in aspect of the intra-century changes of climatic conditions in the region and in European Russia as a whole. The analysis of the relationship between the range expansion of some bird species and the intra-century climate changes was based on ornithological and climatological material available for the study area. We have used material on climate change in the Chuvashian Republic and Volga-Kama Krai since 1926, taking into account recent data of Roshydromet and Intergovernmental Panel on Climate Change. The idea of this study was based on the theory of climatic cycles of different periodicity, the theory of recent global climate change and the hypothesis of cyclic dynamics of the ranges of waterfowl in the context of centuries-old and intra-century climate change in Northern Eurasia. In the framework of the problem, we have studied ornithological material dated from the late 19th till the early 21st century, authored by Bogdanov, Ruzsky, Zhitkov, Buturlin, Artobolevsky, Volchanetsky, Pershakov, Popov, Glushenkov and others. As shown the intra-century climate changes do quite likely affect the northward and northeastward range expansion of such bird species as Cygnus olor, Anas strepera, Aythya ferina, Hieraaetus pennatus, Aquila heliaca, and Fulica atra. Climate changes can also be judged on the base of the shift in the arrival timing to earlier dates for some birds. It is most clearly manifested for early arriving species (Grus grus, Ardea cinerea, Actitis hypoleucos. It is also true for the later arriving Pernis apivorus and Merops apiaster whose existence depends on the

  2. Type-II GaSb/GaAs quantum-dot intermediate band with extended optical absorption range for efficient solar cells

    Science.gov (United States)

    Boustanji, Hela; Jaziri, Sihem

    2018-02-01

    GaSb/GaAs type-II quantum-dot solar cells (QD SCs) have attracted attention as highly efficient intermediate band SCs due to their infrared absorption. Type-II QDs exhibited a staggered confinement potential, where only holes are strongly confined within the dots. Long wavelength light absorption of the QDSCs is enhanced through the improved carriers number in the IB. The absorption of dots depends on their shape, material quality, and composition. Therefore, the optical properties of the GaSbGaAs QDs before and after thermal treatment are studied. Our intraband studies have shown an extended absorption into the long wavelength region 1.77 μ {m}. The annealed QDs have shown significantly more infrared response of 7.2 μ {m} compared to as-grown sample. The photon absorption and hole extraction depend strongly on the thermal annealing process. In this context, emission of holes from localized states in GaSb QDs has been studied using conductance-voltage ( G- V ) characteristics.

  3. Effects of cervical high-velocity low-amplitude techniques on range of motion, strength performance, and cardiovascular outcomes

    DEFF Research Database (Denmark)

    Galindez-Ibarbengoetxea, Xabier; Setuain, Igor; Andersen, Lars L.

    2017-01-01

    BACKGROUND: Cervical high-velocity low-amplitude (HVLA) manipulation technique is among the oldest and most frequently used chiropractic manual therapy, but the physiologic and biomechanics effects were not completely clear. OBJECTIVE: This review aims to describe the effects of cervical HVLA man...... to develop a stronger evidence-based foundation for HVLA manipulation techniques as a treatment for cervical conditions....

  4. Profiting from Probability; Combining Low and High Probability Isotopes as a Tool Extending the Dynamic Range of an Assay Measuring Amphetamine and Methamphetamine in Urine.

    Science.gov (United States)

    Miller, Anna M; Goggin, Melissa M; Nguyen, An; Gozum, Stephanie D; Janis, Gregory C

    2017-06-01

    A wide range of concentrations are frequently observed when measuring drugs of abuse in urine toxicology samples; this is especially true for amphetamine and methamphetamine. Routine liquid chromatography-tandem mass spectrometry confirmatory methods commonly anchored at a 50 ng/mL lower limit of quantitation can span approximately a 100-fold concentration range before regions of non-linearity are reached deteriorating accurate quantitation and qualitative assessments. In our experience, approximately a quarter of amphetamine and methamphetamine positive samples are above a 5,000 ng/mL upper limit of quantitation and thus require reanalysis with dilution for accurate quantitative and acceptable qualitative results. We present here the development of an analytical method capable of accurately quantifying samples with concentrations spanning several orders of magnitude without the need for sample dilution and reanalysis. For each analyte the major isotopes were monitored for analysis through the lower concentration ranges (50-5,000 ng/mL), and the naturally occurring, low probability 13C2 isotopes were monitored for the analysis of the high concentration samples (5,000-100,000 ng/mL amphetamine and 5,000-200,000 ng/mL methamphetamine). The method simultaneously monitors transitions for the molecules containing only 12C and 13C2 isotopologues eliminating the need for re-extraction and reanalysis of high concentration samples. © The Author 2017. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

  5. Short-range magnetic ordering in the geometrically frustrated layered compound YBaCo4O7 with an extended Kagomé structure

    Science.gov (United States)

    Bera, A. K.; Yusuf, S. M.; Banerjee, S.

    2013-02-01

    Structural and magnetic properties of the geometrically frustrated layered compound YBaCo4O7 have been studied by magnetization and neutron diffraction. A layered type crystal structure, with alternating tetrahedral layers of Kagomé and triangular types, along the c axis (hexagonal symmetry, space group P63mc) has been found. The oxygen content of the present compound was determined by iodometric titration to be 7.00 ± 0.01. Presence of a short-range antiferromagnetic ordering (below TN ˜ 110 K) has been concluded from the appearance of an addition broad magnetic peak (at Q ˜ 1.35 Å-1) in the neutron diffraction pattern. A staggered chiral type (√{3}×√{3}) spin structure in the Kagomé layers has been found. Presence of a significant magneto-structural coupling is concluded from the changes in lattice parameters across the magnetic ordering temperature TN ˜ 110 K.

  6. New records of the restinga antwren Formicivora littoralis Gonzaga and Pacheco (Aves, Thamnophilidae in the state of Rio de Janeiro, Brazil: inland extended range and threats

    Directory of Open Access Journals (Sweden)

    MB. Vecchi

    Full Text Available The Restinga Antwren (Formicivora littoralis has a narrow distribution range in southeastern Brazil, and it is a typical species of restinga habitat (sandy coastal plain vegetation. In this paper, we describe two new records for the species (22° 51' 45" S and 42° 14' 13" W; 22° 51' 14" S and 42° 11' 47" W in the northern margin of the Araruama Lagoon, which represent a new inland limit for its distribution (11 km, besides assessing the current state of its habitat. We recorded supposed isolated subpopulations, most of them due the accelerated human-made fragmentation. The Massambaba Environmental Protection Area comprises the larger continuous extent of the suitable habitat for the Restinga Antwren, being essential to its long-term existence. However, the region lacks effective protected areas and, besides urgent practical measures, we recommend an accurate mapping and populational studies on this species.

  7. New records of the restinga antwren Formicivora littoralis Gonzaga and Pacheco (Aves, Thamnophilidae) in the state of Rio de Janeiro, Brazil: inland extended range and threats.

    Science.gov (United States)

    Vecchi, M B; Alves, M A S

    2008-05-01

    The Restinga Antwren (Formicivora littoralis) has a narrow distribution range in southeastern Brazil, and it is a typical species of restinga habitat (sandy coastal plain vegetation). In this paper, we describe two new records for the species (22 degrees 51' 45" S and 42 degrees 14' 13" W; 22 degrees 51' 14" S and 42 degrees 11' 47" W) in the northern margin of the Araruama Lagoon, which represent a new inland limit for its distribution (11 km), besides assessing the current state of its habitat. We recorded supposed isolated subpopulations, most of them due the accelerated human-made fragmentation. The Massambaba Environmental Protection Area comprises the larger continuous extent of the suitable habitat for the Restinga Antwren, being essential to its long-term existence. However, the region lacks effective protected areas and, besides urgent practical measures, we recommend an accurate mapping and populational studies on this species.

  8. Effects of maternal prenatal smoking and birth outcomes extending into the normal range on academic performance in fourth grade in North Carolina, USA.

    Science.gov (United States)

    Anthopolos, Rebecca; Edwards, Sharon E; Miranda, Marie Lynn

    2013-11-01

    Research has documented the adverse relationship of child cognitive development with maternal prenatal smoking and poor birth outcomes. The potential, however, for maternal prenatal smoking to modify the association between birth outcomes and cognitive development is unclear. We linked statewide North Carolina birth data for non-Hispanic white and non-Hispanic black children to end-of-grade test scores in reading and mathematics at fourth grade (n = 65 677). We fit race-stratified multilevel models of test scores regressed on maternal smoking, birth outcomes (as measured by continuous and categorical gestational age and birthweight percentile for gestational age), and their interaction, controlling for maternal- and child-level socio-economic factors. Smoking was consistently associated with decrements in test scores, and better birth outcomes were associated with improvements in test scores, even in clinically normal ranges. Test scores increased quadratically with improving birth outcomes among smoking and non-smoking mothers. Among non-Hispanic white children, the magnitude of the association between gestational age and test scores was larger for children whose mothers smoked during pregnancy compared with the non-smoking group. However, among non-Hispanic black children, birth outcomes did not appear to interact with maternal smoking on test scores. Maternal prenatal smoking may interact with birth outcomes on reading and mathematics test scores, particularly among non-Hispanic white children. Improvements in birth outcomes, even within the clinically normal range, may be associated with improved academic performance. Pregnancy-related exposures and events exert a significant and long-term impact on cognitive development. © 2013 John Wiley & Sons Ltd.

  9. New clues to the local atomic structure of short-range ordered ferric arsenate from extended X-ray absorption fine structure spectroscopy.

    Science.gov (United States)

    Mikutta, Christian; Mandaliev, Petar N; Kretzschmar, Ruben

    2013-04-02

    Short-range ordered ferric arsenate (FeAsO4 · xH2O) is a secondary As precipitate frequently encountered in acid mine waste environments. Two distinct structural models have recently been proposed for this phase. The first model is based on the structure of scorodite (FeAsO4 · 2H2O) where isolated FeO6 octahedra share corners with four adjacent arsenate (AsO4) tetrahedra in a three-dimensional framework (framework model). The second model consists of single chains of corner-sharing FeO6 octahedra being bridged by AsO4 bound in a monodentate binuclear (2)C complex (chain model). In order to rigorously test the accuracy of both structural models, we synthesized ferric arsenates and analyzed their local (absorption fine structure (EXAFS) spectroscopy. We found that both As and Fe K-edge EXAFS spectra were most compatible with isolated FeO6 octahedra being bridged by AsO4 tetrahedra (RFe-As = 3.33 ± 0.01 Å). Our shell-fit results further indicated a lack of evidence for single corner-sharing FeO6 linkages in ferric arsenate. Wavelet-transform analyses of the Fe K-edge EXAFS spectra of ferric arsenates complemented by shell fitting confirmed Fe atoms at an average distance of ∼5.3 Å, consistent with crystallographic data of scorodite and in disagreement with the chain model. A scorodite-type local structure of short-range ordered ferric arsenates provides a plausible explanation for their rapid transformation into scorodite in acid mining environments.

  10. Cryogenic cave carbonates from the Cold Wind Cave, Nízke Tatry Mountains, Slovakia: Extending the age range of cryogenic cave carbonate formation to the Saalian

    Directory of Open Access Journals (Sweden)

    Zak K.

    2009-07-01

    Full Text Available Cold Wind Cave, located at elevations ranging between 1,600 and 1,700 m a. s. l. in the main range of the Nízke Tatry Mountains(Slovakia, is linked in origin with the adjacent Dead Bats Cave. Together, these caves form a major cave system located within anarrow tectonic slice of Triassic sediments. Both caves have undergone complex multiphase development. A system of sub-horizontalcave levels characterized by large, tunnel-like corridors was formed during the Tertiary, when elevation differences surroundingthe cave were less pronounced than today. The central part of the Nízke Tatry Mountains, together with the cave systems, wasuplifted during the Neogene and Lower Pleistocene, which changed the drainage pattern of the area completely. The formation ofnumerous steep-sloped vadose channels and widespread cave roof frost shattering characterized cave development throughout theQuaternary.In the Cold Wind Cave, extensive accumulations of loose, morphologically variable crystal aggregates of secondary cave carbonateranging in size between less than 1 mm to about 35 mm was found on the surface of fallen limestone blocks. Based on the C andO stable isotope compositions of the carbonate (δ13C: 0.72 to 6.34 ‰, δ18O: –22.61 to –13.68 ‰ V-PDB and the negative relationbetween δ13C and δ18O, the carbonate crystal aggregates are interpreted as being cryogenic cave carbonate (CCC. Publishedmodels suggest the formation of CCC in slowly freezing water pools, probably on the surface of cave ice, most probably duringtransitions from stadials to interstadials. Though the formation of these carbonates is likely one of the youngest events in thesequence of formation of cave sediments of the studied caves, the 230Th/234U ages of three samples (79.7±2.3, 104.0±2.9, and180.0±6.3 ka are the oldest so far obtained for CCC in Central Europe. This is the first description of CCC formation in one caveduring two glacial periods (Saalian and Weichselian.

  11. The Cu-MOF-199/single-walled carbon nanotubes modified electrode for simultaneous determination of hydroquinone and catechol with extended linear ranges and lower detection limits.

    Science.gov (United States)

    Zhou, Jian; Li, Xi; Yang, Linlin; Yan, Songlin; Wang, Mengmeng; Cheng, Dan; Chen, Qi; Dong, Yulin; Liu, Peng; Cai, Weiquan; Zhang, Chaocan

    2015-10-29

    A novel electrochemical sensor based on Cu-MOF-199 [Cu-MOF-199 = Cu3(BTC)2 (BTC = 1,3,5-benzenetricarboxylicacid)] and SWCNTs (single-walled carbon nanotubes) was fabricated for the simultaneous determination of hydroquinone (HQ) and catechol (CT). The modification procedure was carried out through casting SWCNTs on the bare glassy carbon electrode (GCE) and followed by the electrodeposition of Cu-MOF-199 on the SWCNTs modified electrode. Cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS) and scanning electron microscopy (SEM) were performed to characterize the electrochemical performance and surface characteristics of the as-prepared sensor. The composite electrode exhibited an excellent electrocatalytic activity with increased electrochemical signals towards the oxidation of HQ and CT, owing to the synergistic effect of SWCNTs and Cu-MOF-199. Under the optimized condition, the linear response range were from 0.1 to 1453 μmol L(-1) (RHQ = 0.9999) for HQ and 0.1-1150 μmol L(-1) (RCT = 0.9990) for CT. The detection limits for HQ and CT were as low as 0.08 and 0.1 μmol L(-1), respectively. Moreover, the modified electrode presented the good reproducibility and the excellent anti-interference performance. The analytical performance of the developed sensor for the simultaneous detection of HQ and CT had been evaluated in practical samples with satisfying results. Copyright © 2015 Elsevier B.V. All rights reserved.

  12. Measurement of the neutron fields produced by a 62 MeV proton beam on a PMMA phantom using extended range Bonner sphere spectrometers

    Science.gov (United States)

    Amgarou, K.; Bedogni, R.; Domingo, C.; Esposito, A.; Gentile, A.; Carinci, G.; Russo, S.

    2011-10-01

    The experimental characterization of the neutron fields produced as parasitic effect in medical accelerators is assuming an increased importance for either the patient protection or the facility design aspects. Medical accelerators are diverse in terms of particle type (electrons or hadrons) and energy, but the radiation fields around them have in common (provided that a given threshold energy is reached) the presence of neutrons with energy span over several orders of magnitude. Due to the large variability of neutron energy, field or dosimetry measurements in these workplaces are very complex, and in general, cannot be performed with ready-to-use commercial instruments. In spite of its poor energy resolution, the Bonner Sphere Spectrometer (BSS) is the only instrument able to simultaneously determine all spectral components in such workplaces. The energy range of this instrument is limited to EFisica Nucleare—Laboratori Nazionali di Frascati) were exposed to characterize the "forward" and "sideward" proton-induced neutron fields. The use of two ERBSS characterized by different set of spheres, central detectors, and independently established and calibrated, is important for guaranteeing the robustness of the measured spectra and estimating their overall uncertainties.

  13. Measurements of the capture cross sections of natural silver in the resonance range with the time of flight technique

    Directory of Open Access Journals (Sweden)

    Šalamon L.

    2017-01-01

    Full Text Available Neutron capture cross section measurements have been performed at the time-of-flight facility GELINA of the EC-JRC-Geel. Prompt gamma rays, originating from a natural silver sample, were detected by a pair of C6D6 liquid scintillation detectors. The total energy detection principle in combination with the pulse height weighting technique has been used. In this contribution the experimental details together with the data reduction process are described. In addition, first results of calculations with REFIT are presented to verify the quality of recommended cross section data in the resolved resonance region.

  14. Comparative study on three highly sensitive absorption measurement techniques characterizing lithium niobate over its entire transparent spectral range.

    Science.gov (United States)

    Leidinger, M; Fieberg, S; Waasem, N; Kühnemann, F; Buse, K; Breunig, I

    2015-08-24

    We employ three highly sensitive spectrometers: a photoacoustic spectrometer, a photothermal common-path interferometer and a whispering-gallery-resonator-based absorption spectrometer, for a comparative study of measuring the absorption coefficient of nominally transparent undoped, congruently grown lithium niobate for ordinarily and extraordinarily polarized light in the wavelength range from 390 to 3800 nm. The absorption coefficient ranges from below 10(-4) cm(-1) up to 2 cm(-1). Furthermore, we measure the absorption at the Urbach tail as well as the multiphonon edge of the material by a standard grating spectrometer and a Fourier-transform infrared spectrometer, providing for the first time an absorption spectrum of the whole transparency window of lithium niobate. The absorption coefficients obtained by the three highly sensitive and independent methods show good agreement.

  15. Temperature dependence of the thermal diffusivity of GaAs in the 100-305 K range measured by the pulsed photothermal displacement technique

    Science.gov (United States)

    Soltanolkotabi, M.; Bennis, G. L.; Gupta, R.

    1999-01-01

    We have measured the variation of the value of the thermal diffusivity of semi-insulating GaAs in the 100-305 K range. The method used is the pulsed photothermal displacement technique. This is a noncontact technique, and the value of the thermal diffusivity is derived from the temporal evolution of the signal rather than its amplitude. This makes the technique less susceptible to uncertainties. We find that the temperature dependence of the thermal conductivity of semi-insulating GaAs follows a power law as T-1.62, in disagreement with results obtained previously. Possible reasons for the deviation within this very important intermediate temperature range are discussed.

  16. Extended Emotions

    OpenAIRE

    Krueger, Joel; Szanto, Thomas

    2016-01-01

    Until recently, philosophers and psychologists conceived of emotions as brain- and body-bound affairs. But researchers have started to challenge this internalist and individualist orthodoxy. A rapidly growing body of work suggests that some emotions incorporate external resources and thus extend beyond the neurophysiological confines of organisms; some even argue that emotions can be socially extended and shared by multiple agents. Call this the extended emotions thesis (ExE). In this article...

  17. Long-range compaction and flexibility of interphase chromatin in budding yeast analyzed by high-resolution imaging techniques

    Science.gov (United States)

    Bystricky, Kerstin; Heun, Patrick; Gehlen, Lutz; Langowski, Jörg; Gasser, Susan M.

    2004-11-01

    Little is known about how chromatin folds in its native state. Using optimized in situ hybridization and live imaging techniques have determined compaction ratios and fiber flexibility for interphase chromatin in budding yeast. Unlike previous studies, ours examines nonrepetitive chromatin at intervals short enough to be meaningful for yeast chromosomes and functional domains in higher eukaryotes. We reconcile high-resolution fluorescence in situ hybridization data from intervals of 14-100 kb along single chromatids with measurements of whole chromosome arms (122-623 kb in length), monitored in intact cells through the targeted binding of bacterial repressors fused to GFP derivatives. The results are interpreted with a flexible polymer model and suggest that interphase chromatin exists in a compact higher-order conformation with a persistence length of 170-220 nm and a mass density of 110-150 bp/nm. These values are equivalent to 7-10 nucleosomes per 11-nm turn within a 30-nm-like fiber structure. Comparison of long and short chromatid arm measurements demonstrates that chromatin fiber extension is also influenced by nuclear geometry. The observation of this surprisingly compact chromatin structure for transcriptionally competent chromatin in living yeast cells suggests that the passage of RNA polymerase II requires a very transient unfolding of higher-order chromatin structure. higher-order structure | 30-nm fiber | nucleosomes

  18. A note on using a laser-based technique for recording of behaviour and location of free-ranging animals.

    Science.gov (United States)

    Fehmi, J S.; Laca, E A.

    2001-03-29

    We developed a precise, remote (up to 300m) observation system to record animal location and behaviour that requires no animal handling or disruption of the normal environment. Our system, combining a survey laser and a laptop, also allows recording of observed animal behaviour from seconds to hours, with accuracy of 1m or better. Up to one individual per second can be located, which supports data collection of large numbers of animals not possible with other methods. The laser system was used to track a halter-broken heifer led in an arc beginning and ending about 50m from the laser with a maximum distance of about 150m. We recorded the location of the heifer at 35 points along the arc using the laser, a global positioning system (GPS), and a nylon tape. There was an average linear difference of 1.16m (S.D. 0.63) between the laser data and the GPS data. The laser was potentially more accurate than GPS for this application because the laser averaged only 0.21m (S.D. 0.24) linear difference from the tape. Tests of the laser to relocate points in the field to within 0.20m and 0.1 degrees, averaged 0.42m (S.D. 0.29) from the original points. Our technique allows precise location of behaviour and navigation to grazed sites, potentially revealing how animals interact with the resources they exploit and showing the effect of landscape spatial heterogeneity on foraging and habitat use patterns.

  19. The long-range transport of aerosols from northern China to Hong Kong - a multi-technique study

    Science.gov (United States)

    Fang, M.; Zheng, M.; Wang, F.; Chim, K. S.; Kot, S. C.

    The results of the inorganic and organic analyses of aerosol samples collected on the east and west sides of Hong Kong during a dust episode (9-10 May 1996) are reported. The origin of the dust was traced to Northern China. The dust reached Hong Kong by way of the East China Sea. The characteristics of the inorganic elements and organic compounds were quite different from the non-episodic samples collected on 1-2 April 1996, EPD (Environmental Protection Department, Special Administrative Region, Hong Kong, China) results for April-May 1994, and our early studies (Zheng et al., 1997. Atmospheric Environment 31(2), 227-237.). Results from X-ray spectrometry showed pronounced increase in the relative abundance of Al, Fe, Ca, S and Cl in the dust samples compared to the non-episodic samples. The high abundance of Cl in the dust samples suggested the aerosols experienced long-range transport by way of the sea. ICP-MS analysis revealed higher concentrations of Fe, Ca, S and Pb in the episodic samples relative to the values measured during April-May 1994 by EPD. The high Ca content in the soil samples is a characteristic of northern Chinese crustal material (Liu et al., 1985). Hong Kong aerosols are characterized by high octadecenoic acid concentration due to heavy urbanization and Chinese-style stir-fry cooking. A much lower C 18:1/C 18:0 ratio was found in the episodic samples, however, suggesting the aerosols were transported from a long distance. The high ratio of ⩾C 20/Asian Dust. This is the first scientific report of Asian Dust in Hong Kong.

  20. Techniques for Mitigating Thermal Fatigue Degradation, Controlling Efficiency, and Extending Lifetime in a ZnO Thermoelectric Using Grain Size Gradient FGMs

    Science.gov (United States)

    Cramer, Corson L.; Li, Wenjie; Jin, Zhi-He; Wang, Jue; Ma, Kaka; Holland, Troy B.

    2018-01-01

    A functionally graded material (FGM) in terms of grain size gradation is fabricated using zinc oxide (ZnO) with spark plasma sintering and an additive manufacturing technique by diffusion bonding layers of material sintered at different temperatures to achieve a thermoelectric generator (TEG) material that can dissipate heat well and retain high energy conversion efficiency for longer-lasting and comparably efficient TEGs. This FGM is compared to a previously made FGM with continuous grain size gradation. Uniform and graded grain size conditions are modeled for thermoelectric output by using thermoelectric properties of the uniform grain size as well as the varying properties seen in the FGMs. The actual thermoelectric output of the samples is measured and compared to the simulations. The grain size has a large effect on the efficiency and efficiency range. The samples are thermally cycled with a fast heating rate to test the thermal stress robustness and degradation, and the resistance at the highest temperature is measured to indicate degradation from thermal stress. The measured efficiency after cycling shows that the FGMs survive longer lifetime than that with uniform small grains.

  1. Systematic evaluation of the root cause of non-linearity in liquid chromatography/tandem mass spectrometry bioanalytical assays and strategy to predict and extend the linear standard curve range.

    Science.gov (United States)

    Yuan, Long; Zhang, Duxi; Jemal, Mohammed; Aubry, Anne-Francoise

    2012-06-30

    The linear range of a liquid chromatography/tandem mass spectrometry (LC/MS/MS) bioanalytical assay is typically about three orders of magnitude. A broader standard curve range is favored since it can significantly reduce the time, labor and potential errors related to sample dilution - one of the bottlenecks in sample analysis. Using quadratic regression to fit the standard curve can, to a certain degree, extend the dynamic range. However, the use of a quadratic regression is controversial, particularly in regulated bioanalysis. A number of compounds, with different physicochemical properties and ionization efficiencies, were evaluated to understand the cause of the non-linear behavior of the standard curve. The standard curve behavior is primarily associated with the absolute analyte response but not the analyte concentration, the properties of the analyte, or the nature of the matrix when a stable-isotope-labeled internal standard (SIL-IS) is used. For all the test compounds, a non-linear curve was observed when signals exceeded a certain response, which depends on the detector used in the mass spectrometer. With typical API4000 instruments used for the experiments, this critical response level was determined to be ~1 E+6 counts per second (cps) and it was successfully used to predict the linear ranges for the test compounds. By simultaneously monitoring two selective reaction monitoring (SRM) channels of different intensity and using SIL-IS, a linear range of five orders of magnitude was achieved. In this work, the root cause of the non-linear behavior of the standard curve when using a SIL-IS was investigated and identified. Based on the findings, an improved multiple SRM channels approach was proposed and successfully applied to obtain a linear dynamic range of five orders of magnitude for one test compound. This approach may work particularly well for LC/MS/MS bioanalytical assay of dried blood spot (DBS) samples, for which a direct dilution is cumbersome

  2. Extended Emotions

    DEFF Research Database (Denmark)

    Krueger, Joel; Szanto, Thomas

    2016-01-01

    beyond the neurophysiological confines of organisms; some even argue that emotions can be socially extended and shared by multiple agents. Call this the extended emotions thesis (ExE). In this article, we consider different ways of understanding ExE in philosophy, psychology, and the cognitive sciences....... First, we outline the background of the debate and discuss different argumentative strategies for ExE. In particular, we distinguish ExE from cognate but more moderate claims about the embodied and situated nature of cognition and emotion (Section 1). We then dwell upon two dimensions of ExE: emotions......Until recently, philosophers and psychologists conceived of emotions as brain- and body-bound affairs. But researchers have started to challenge this internalist and individualist orthodoxy. A rapidly growing body of work suggests that some emotions incorporate external resources and thus extend...

  3. Extended thermodynamics

    CERN Document Server

    Müller, Ingo

    1993-01-01

    Physicists firmly believe that the differential equations of nature should be hyperbolic so as to exclude action at a distance; yet the equations of irreversible thermodynamics - those of Navier-Stokes and Fourier - are parabolic. This incompatibility between the expectation of physicists and the classical laws of thermodynamics has prompted the formulation of extended thermodynamics. After describing the motifs and early evolution of this new branch of irreversible thermodynamics, the authors apply the theory to mon-atomic gases, mixtures of gases, relativistic gases, and "gases" of phonons and photons. The discussion brings into perspective the various phenomena called second sound, such as heat propagation, propagation of shear stress and concentration, and the second sound in liquid helium. The formal mathematical structure of extended thermodynamics is exposed and the theory is shown to be fully compatible with the kinetic theory of gases. The study closes with the testing of extended thermodynamics thro...

  4. Mapping the pharyngeal and intestinal pH of Caenorhabditis elegans and real-time luminal pH oscillations using extended dynamic range pH-sensitive nanosensors.

    Science.gov (United States)

    Chauhan, Veeren M; Orsi, Gianni; Brown, Alan; Pritchard, David I; Aylott, Jonathan W

    2013-06-25

    Extended dynamic range pH-sensitive ratiometric nanosensors, capable of accurately mapping the full physiological pH range, have been developed and used to characterize the pH of the pharyngeal and intestinal lumen of Caenorhabditis elegans in real-time. Nanosensors, 40 nm in diameter, were prepared by conjugating pH-sensitive fluorophores, carboxyfluorescein (FAM) and Oregon Green (OG) in a 1:1 ratio, and a reference fluorophore, 5-(and-6)-carboxytetramethylrhodamine (TAMRA) to an inert polyacrylamide matrix. Accurate ratiometric pH measurements were calculated through determination of the fluorescence ratio between the pH-sensitive and reference fluorophores. Nanosensors were calibrated with an automated image analysis system and validated to demonstrate a pH measurement resolution of ±0.17 pH units. The motility of C. elegans populations, as an indicator for viability, showed nematodes treated with nanosensors, for concentrations ranging from 50.00 to 3.13 mg/mL, were not statistically different to nematodes not challenged with nanosensors up to a period of 4 days (p nanosensors were also found to remain in the C. elegans lumen >24 h after nanosensor challenge was removed. The pH of viable C. elegans lumen was found to range from 5.96 ± 0.31 in the anterior pharynx to 3.59 ± 0.09 in the posterior intestine. The pharyngeal pumping rate, which dictates the transfer of ingested material from the pharynx to the intestine, was found to be temperature dependent. Imaging C. elegans at 4 °C reduced the pharyngeal pumping rate to 7 contractions/min and enabled the reconstruction of rhythmic pH oscillations in the intestinal lumen in real-time with fluorescence microscopy.

  5. An Approach to 3d Digital Modeling of Surfaces with Poor Texture by Range Imaging Techniques. `SHAPE from Stereo' VS. `SHAPE from Silhouette' in Digitizing Jorge Oteiza's Sculptures

    Science.gov (United States)

    García Fernández, J.; Álvaro Tordesillas, A.; Barba, S.

    2015-02-01

    Despite eminent development of digital range imaging techniques, difficulties persist in the virtualization of objects with poor radiometric information, in other words, objects consisting of homogeneous colours (totally white, black, etc.), repetitive patterns, translucence, or materials with specular reflection. This is the case for much of the Jorge Oteiza's works, particularly in the sculpture collection of the Museo Fundación Jorge Oteiza (Navarra, Spain). The present study intend to analyse and asses the performance of two digital 3D-modeling methods based on imaging techniques, facing cultural heritage in singular cases, determined by radiometric characteristics as mentioned: Shape from Silhouette and Shape from Stereo. On the other hand, the text proposes the definition of a documentation workflow and presents the results of its application in the collection of sculptures created by Oteiza.

  6. A specimen of Paralycoptera Chang & Chou 1977 (Teleostei: Osteoglossoidei from Hong Kong (China with a potential Late Jurassic age that extends the temporal and geographical range of the genus

    Directory of Open Access Journals (Sweden)

    Tze-Kei Tse

    2015-03-01

    Full Text Available We describe a Mesozoic fish Paralycoptera sp. (Teleostei: Osteoglossoidei, on the basis of a postcranial skeleton collected from the volcaniclastic mudstones of the Lai Chi Chong Formation of Hong Kong, China. The new finding—representing the city’s first Mesozoic fish—extends the geographical distribution of Paralycoptera from eastern mainland China into Hong Kong, demonstrating a wider distribution than previously appreciated for this genus. A radiometric age for the Lai Chi Chong Formation of 146.6 ± 0.2 Ma implies a temporal range expansion for Paralycoptera of approximately 40 million years back from the Early Cretaceous (∼110 Ma. However, spores found in the Formation suggest an Early Cretaceous age that is consistent with the existing age assignment to Paralycoptera. We argue that the proposed temporal range extension is genuine because it is based on recent high precision radiometric age data, but given the discrepancies with the biostratigraphic ages further investigation is needed to confirm this. This study provides an important step towards revealing Hong Kong’s Mesozoic vertebrate fauna and understanding its relationship to well-studied mainland Chinese ones.

  7. date extended

    Indian Academy of Sciences (India)

    C A L AN DER OF EVENTS. Date of issue of bid document : 2016 September 21. Extended Due date and Time for Receipt of Tender : Up to 2016 October 17, Time 13:00 Hrs. Date and Time of opening of bid : 2016 October 17, Time 15:00 Hrs. Cost of Bid Document : Rs. 100/- only (Non-refundable). Earnest Money Deposit ...

  8. Extending Puppet

    CERN Document Server

    Franceschi, Alessandro

    2014-01-01

    This book is a clear, detailed and practical guide to learn about designing and deploying you puppet architecture, with informative examples to highlight and explain concepts in a focused manner. This book is designed for users who already have good experience with Puppet, and will surprise experienced users with innovative topics that explore how to design, implement, adapt, and deploy a Puppet architecture. The key to extending Puppet is the development of types and providers, for which you must be familiar with Ruby.

  9. Pixel multiplexing technique for real-time three-dimensional-imaging laser detection and ranging system using four linear-mode avalanche photodiodes

    Energy Technology Data Exchange (ETDEWEB)

    Xu, Fan; Wang, Yuanqing, E-mail: yqwang@nju.edu.cn; Li, Fenfang [School of Electronic Science and Engineering, Nanjing University, Nanjing 210046 (China)

    2016-03-15

    The avalanche-photodiode-array (APD-array) laser detection and ranging (LADAR) system has been continually developed owing to its superiority of nonscanning, large field of view, high sensitivity, and high precision. However, how to achieve higher-efficient detection and better integration of the LADAR system for real-time three-dimensional (3D) imaging continues to be a problem. In this study, a novel LADAR system using four linear mode APDs (LmAPDs) is developed for high-efficient detection by adopting a modulation and multiplexing technique. Furthermore, an automatic control system for the array LADAR system is proposed and designed by applying the virtual instrumentation technique. The control system aims to achieve four functions: synchronization of laser emission and rotating platform, multi-channel synchronous data acquisition, real-time Ethernet upper monitoring, and real-time signal processing and 3D visualization. The structure and principle of the complete system are described in the paper. The experimental results demonstrate that the LADAR system is capable of achieving real-time 3D imaging on an omnidirectional rotating platform under the control of the virtual instrumentation system. The automatic imaging LADAR system utilized only 4 LmAPDs to achieve 256-pixel-per-frame detection with by employing 64-bit demodulator. Moreover, the lateral resolution is ∼15 cm and range accuracy is ∼4 cm root-mean-square error at a distance of ∼40 m.

  10. Immediate Effects of Mobilization With Movement vs Sham Technique on Range of Motion, Strength, and Function in Patients With Shoulder Impingement Syndrome: Randomized Clinical Trial.

    Science.gov (United States)

    Guimarães, João Flávio; Salvini, Tania Fátima; Siqueira, Aristides Leite; Ribeiro, Ivana Leão; Camargo, Paula Rezende; Alburquerque-Sendín, Francisco

    The purpose of this study was to compare the immediate effects of mobilization with movement (MWM) with sham technique on range of motion (ROM), muscle strength, and function in patients with shoulder impingement syndrome. A randomized clinical study was performed. Participants (mean age ± standard deviation, 31 ± 8 years; 56% women) were divided into 2 groups: group 1 (n = 14), which received the MWM technique in the first 4 sessions and the sham technique in the last 4 sessions; and group 2 (n = 13), which was treated with the opposite order of treatment conditions described for group 1. Shoulder ROM, isometric peak force assessed with a handheld dynamometer, and function as determined through the Disabilities of the Arm, Shoulder and Hand and Shoulder Pain and Disability Index (SPADI) questionnaires were collected at preintervention, interchange, and postintervention moments. Two-way analysis of variance revealed no significant group-by-time interaction for any outcome but did reveal a main time effect for shoulder external rotation (P = .04) and abduction (P = .01) ROM, Disabilities of the Arm, Shoulder and Hand (P shoulder ROM during external rotation and abduction, pain, and function in patients with shoulder impingement syndrome. Copyright © 2016. Published by Elsevier Inc.

  11. Extended family medicine training

    Science.gov (United States)

    Slade, Steve; Ross, Shelley; Lawrence, Kathrine; Archibald, Douglas; Mackay, Maria Palacios; Oandasan, Ivy F.

    2016-01-01

    Abstract Objective To examine trends in family medicine training at a time when substantial pedagogic change is under way, focusing on factors that relate to extended family medicine training. Design Aggregate-level secondary data analysis based on the Canadian Post-MD Education Registry. Setting Canada. Participants All Canadian citizens and permanent residents who were registered in postgraduate family medicine training programs within Canadian faculties of medicine from 1995 to 2013. Main outcome measures Number and proportion of family medicine residents exiting 2-year and extended (third-year and above) family medicine training programs, as well as the types and numbers of extended training programs offered in 2015. Results The proportion of family medicine trainees pursuing extended training almost doubled during the study period, going from 10.9% in 1995 to 21.1% in 2013. Men and Canadian medical graduates were more likely to take extended family medicine training. Among the 5 most recent family medicine exit cohorts (from 2009 to 2013), 25.9% of men completed extended training programs compared with 18.3% of women, and 23.1% of Canadian medical graduates completed extended training compared with 13.6% of international medical graduates. Family medicine programs vary substantially with respect to the proportion of their trainees who undertake extended training, ranging from a low of 12.3% to a high of 35.1% among trainees exiting from 2011 to 2013. Conclusion New initiatives, such as the Triple C Competency-based Curriculum, CanMEDS–Family Medicine, and Certificates of Added Competence, have emerged as part of family medicine education and credentialing. In acknowledgment of the potential effect of these initiatives, it is important that future research examine how pedagogic change and, in particular, extended training shapes the care family physicians offer their patients. As part of that research it will be important to measure the breadth and uptake of

  12. THE COMBINED EFFECTIVENESS OF GLENOHUMERAL END-RANGE MOBILIZATION AND CONTRACT-RELAX TECHNIQUE FOR GLENOHUMERAL INTERNAL ROTATORS IN SUBJECTS WITH ADHESIVE CAPSULITIS

    Directory of Open Access Journals (Sweden)

    Abhijit Kalita

    2015-10-01

    Full Text Available Background: Frozen shoulder is an insidious condition that begins with pain and gradual restriction of movement in the shoulder region. There are various methods of treating frozen shoulder (both surgical and non-surgical.Among the non-surgical methods there is no specific method accepted universally. Purpose of this study is to determine the combined effectiveness of Glenohumeral End-Range Mobilization and Contract-Relax technique for glenohumeral internal rotators in patients with adhesive capsulitis. Methods: 60 frozen shoulder patients randomized 30 subjects into each experimental and control group. Group A (experimental group received Glenohumeral End-Range Mobilization, Contract-Relax Technique for glenohumeral internal rotators and Shoulder Pendular Exercises 2 times a week for a period of 4 weeks (8 sessions.Group B (control group received Shoulder Pendular exercises 2 times a week for a period of 4 weeks (8 sessions. Outcome measures included are VAS, SPADI and goniometry for assessing pain, functional ability and ROM for the shoulder joint. Results: The average improvement of VAS for Group A and Group B were 4.5 and 3 respectively using median. The U-value was 176, which is statistically highly significant (p value = 0.000.The average improvement of Shoulder Pain and Disability Index for Group A and group B were 56.9333 and 10.3667 respectively using mean and Standard Deviation. The t-value was 35.91181, which is statistically highly significant (p value = 0.000. Conclusion: The results indicated that both Group A and Group B had significant improvement in the scores of VAS, SPADI and GONIOMETRY scores at the 4th week when compared to base line values, but when comparing the end results of group A and group B it has been found out that group A intervention is more effective then Group B in treating the internal rotators of patients with adhesive capsulitis

  13. Para-aortic and pelvic extended-field radiotherapy for advanced-stage uterine cancer: dosimetric and toxicity comparison between the four-field box and intensity-modulated techniques.

    Science.gov (United States)

    Rabinovich, A; Bernard, L; Ramanakumar, A V; Stroian, G; Gotlieb, W H; Lau, S; Bahoric, B

    2015-12-01

    In patients with advanced-stage endometrial carcinoma (eca), extended-field radiotherapy (efrt) is traditionally delivered by the 3-dimensional conformal (3d-crt) 4-field box technique. In recent years, the use of intensity-modulated radiotherapy (imrt) in gynecologic cancers has increased. We compared the delivery of efrt by the 3d-crt and contemporary imrt techniques. After surgical staging and adjuvant chemotherapy in 38 eca patients, efrt was delivered by either imrt or 3d-crt. Doses to the organs at risk, side effects, and outcomes were compared between the techniques. Of the 38 eca patients, 33 were stage iiic, and 5 were stage ivb. In the imrt group, maximal doses to rectum, small intestine, and bladder were significantly higher, and mean dose to bladder was lower (p groups. In long-term follow-up, only grade 1 cystitis at 3 months was statistically higher in the imrt patients. No grade iii or iv gastrointestinal or genitourinary toxicities were observed. No statistically significant differences in overall and disease-free survival or recurrence rates were observed between the techniques. In advanced eca patients, imrt is a safe and effective technique for delivering efrt to the pelvis and para-aortic region, and it is comparable to the 3d-crt 4-field box technique in both side effects and efficacy. For centres in which imrt is not readily available, 3d-crt is a valid alternative.

  14. Extending Experiences

    DEFF Research Database (Denmark)

    A computer game's player is experiencing not only the game as a designer-made artefact, but also a multitude of social and cultural practices and contexts of both computer game play and everyday life. As a truly multidisciplinary anthology, Extending Experiences sheds new light on the mesh...... of possibilities and influences the player engages with. Part one, Experiential Structures of Play, considers some of the key concepts commonly used to address the experience of a computer game player. The second part, Bordering Play, discusses conceptual and practical overlaps of games and everyday life...... and the impacts of setting up, crossing and breaking the boundaries of game and non-game. Part three, Interfaces of Play, looks at games as technological and historical artefacts and commodities. The fourth part, Beyond Design, introduces new models for the practical and theoretical dimensions of game design....

  15. Optical properties measurement of laser coagulated tissues with double integrating sphere and inverse Monte Carlo technique in the wavelength range from 350 to 2100 nm

    Science.gov (United States)

    Honda, Norihiro; Nanjo, Takuya; Ishii, Katsunori; Awazu, Kunio

    2012-03-01

    In laser medicine, the accurate knowledge about the optical properties (absorption coefficient; μa, scattering coefficient; μs, anisotropy factor; g) of laser irradiated tissues is important for the prediction of light propagation in tissues, since the efficacy of laser treatment depends on the photon propagation within the irradiated tissues. Thus, it is likely that the optical properties of tissues at near-ultraviolet, visible and near-infrared wavelengths will be more important due to more biomedical applications of lasers will be developed. For improvement of the laser induced thermotherapy, the optical property change during laser treatment should be considered in the wide wavelength range. For estimation of the optical properties of the biological tissues, the optical properties measurement system with a double integrating sphere setup and an inverse Monte Carlo technique was developed. The optical properties of chicken muscle tissue were measured in the native state and after laser coagulation using the optical properties measurement system in the wavelength range from 350 to 2100 nm. A CO2 laser was used for laser coagulation. After laser coagulation, the reduced scattering coefficient of the tissue increased. And, the optical penetration depth decreased. For improvement of the treatment depth during laser coagulation, a quantitative procedure using the treated tissue optical properties for determination of the irradiation power density following light penetration decrease might be important in clinic.

  16. EFFICACY OF KALTENBORN GRADE III MOBILIZATIONS, MUSCLE ENERGY TECHNIQUES AND THEIR COMBINATION TO IMPROVE RANGE AND FUNCTIONAL ABILITY IN ADULTS WITH MECHANICAL NECK PAIN

    Directory of Open Access Journals (Sweden)

    Naveed Anwar

    2016-08-01

    Full Text Available Background: Physiotherapy is an essentialtreatment in the management of Mechanical Neck ache, still there was lack of literature seen supporting the effectiveness of Physiotherapy interventions with their doses targeting specific group of population. The focus of study was to see the effectiveness of Kaltenborn Grade III mobilization, Muscle Energy Techniques and their combination to improve range and functional ability in patients with Mechanical Neck ache. Methods: 72 patients with Mechanical Neck achewere randomly categorized in 3 groups (Mobilization, METs and Combination group. NDI scale and goniometry was used as an assessment tool to measure the outcome before and after treatment (follow up 1 week. Results: According to the results there was significant improvement seen in Combination group (Mobilization and METs in terms of pain, which decreased from 7.70±0.69 to 1.25±1.93 (p=0.00, gain in ROM e.g. Cervical Flexion (27.29±2.38 to 37.54±3.14. Whereas, marked significance (p=0.00 was seen in the NDI score and percentage of Combination group. ANOVA tells us that difference was significant in all three groups in categories of pain (VAS, gain in cervical ranges and NDI score and percentage as p=0.00. Combination group had significant difference within the groups then METs and Mobilization group in all categories of VAS, Cervical ranges, NDI score and percentage. Conclusion: Combination of (Grade III Kaltenborn and METs was seen more effective in terms of improving Mechanical Neck Pain, in smaller treatment session (7 days only.

  17. Measuring Relative Motions Across a Fault Using Seafloor Transponders Installed at Close Range to each Other Based on Differential GPS/Acoustic Technique

    Science.gov (United States)

    Kido, M.; Ashi, J.; Tsuji, T.; Tomita, F.

    2016-12-01

    Seafloor geodesy based on acoustic ranging technique is getting popular means to reveal crustal deformation beneath the ocean. GPS/acoustic technique can be applied to monitoring regional deformation or absolute position, while direct-path acoustic ranging can be applied to detecting localized strain or relative motion in a short distance ( 1-10 km). However the latter observation sometimes fails to keep the clearance of an acoustic path between the seafloor transponders because of topographic obstacle or of downward bending nature of the path due to vertical gradient of sound speed in deep-ocean. Especially at steep fault scarp, it is almost impossible to keep direct path between the top and bottom of the fault scarp. Even in such a situation, acoustic path to the sea surface might be always clear. Then we propose a new approach to monitor the relative motion of across a fault scarp using "differential" GPS/acoustic measurement, which account only for traveltime differences among the transponders. The advantages of this method are that: (1) uncertainty in sound speed in shallow water is almost canceled; (2) possible GPS error is also canceled; (3) picking error in traveltime detection is almost canceled; (4) only a pair of transponders can fully describe relative 3-dimensional motion. On the other hand the disadvantages are that: (5) data is not continuous but only campaign; (6) most advantages are only effective only for very short baseline (< 100-300 m). Our target being applied this method is a steep fault scarp near the Japan trench, which is expected as a surface expression of back thrust, in where time scale of fault activity is still controversial especially after the Tohoku earthquake. We have carefully installed three transponders across this scarp using a NSS system, which can remotely navigate instrument near the seafloor from a mother vessel based on video camera image. Baseline lengths among the transponders are 200-300 m at 3500 m depth. Initial

  18. Evaluating synergy effects of combined close-range and remote sensing techniques for the monitoring of a deep-seated landslide (Schmirn, Austria)

    Science.gov (United States)

    Rutzinger, Martin; Zieher, Thomas; Pfeiffer, Jan; Schlögel, Romy; Darvishi, Mehdi; Toschi, Isabella; Remondino, Fabio

    2017-04-01

    In the recent past, studies on the monitoring of deep-seated landslides included a multitude of measuring techniques. Direct and indirect methods are applied for displacement measurements at points, along lines or area-wide. In particular close-range and remote sensing has proven to be feasible for the detection of displacements featuring a high accuracy (range of cm to dm) while covering the whole area of interest. However, a combination of supplementing methods is preferable to confirm the observations and to overcome their individual drawbacks and limitations. In the present study, displacements of a deep-seated landslide situated in the Schmirn valley (Tyrol, Austria) are assessed by (i) image correlation of existing orthophoto series, (ii) multi-temporal data acquisitions using a terrestrial laser scanner (TLS) and (iii) repeated measurements with the help of a differential global positioning system (DGPS). The study focusses on evaluating the synergy effects of the tested methods in quantifying the landslide's movement. Limitations concerning their spatial resolution and accuracy are addressed in specific detail. The landslide's activity is likely controlled by hillslope hydrology and its seasonality. Phases of enhanced movement are expected in the course of snowmelt and after exceptional rainfall events. Preliminary results of the image correlation reveal mean annual horizontal displacement rates of 0.75 m (±0.45 m; one standard deviation), which is confirmed by the DGPS measurements. The first results also suggest constant annual displacement rates for the period of 2004 to 2015. Further comparisons with the multi-temporal TLS data will reveal detailed spatial patterns of displacement rates and deepen the understanding of the landslide's kinematics. This research is conducted within the project LEMONADE (http://lemonade.mountainresearch.at) funded by the Euregio Science Fund.

  19. A study on microstructures and extended defects in Ni- and Co-base superalloys. Development and application of advanced TEM techniques

    Energy Technology Data Exchange (ETDEWEB)

    Mueller, Julian

    2016-04-21

    To improve the efficiency of stationary gas turbines and air craft jet engines, it is crucial to increase the maximum temperature capabilities of single crystalline superalloys by appropriate alloy design and microstructure tuning. The mechanical properties of superalloys are largely influenced by the physical constitution of the microstructure. To develop a better understanding of fundamental aspects of creep deformation, like the stress states, defect structures and other degradation processes, it is necessary to employ scale-bridging characterization. In the present work, Ni- and Co-based superalloys are investigated by a series of advanced transmission electron microscopy techniques and by the application of specifically developed characterization methods to identify dominating processes on atomic scale and hence to make a direct correlation to the macroscopic creep behavior. For instance, the misfit between γ and γ' in the initial microstructure is of great importance, since it strongly influences the rafting process and the interfacial dislocation network. To address the stress state, on the one hand misfit measurements in undeformed samples are conducted and are directly compared to finite-element simulations. On the other hand, deformed samples are investigated to assess the influence of an initial rafting process and the formation of an interface dislocation network. For this, characterization methods are used which are based on the evaluation of atomically resolved images and on electron diffraction. Moreover, the temperature dependency of the misfit and of the microstructure stability is specifically investigated for different Co-base alloys in in situ heating experiments. The characterization of defect structures in Ni-base superalloys after creep deformation builds the second pillar of this work. Specific cutting processes of superdislocations are studied to elucidate which atomic processes take place. A series of left angle 100 right angle and

  20. Multivariate Analysis, Mass Balance Techniques, and Statistical Tests as Tools in Igneous Petrology: Application to the Sierra de las Cruces Volcanic Range (Mexican Volcanic Belt

    Directory of Open Access Journals (Sweden)

    Fernando Velasco-Tapia

    2014-01-01

    Full Text Available Magmatic processes have usually been identified and evaluated using qualitative or semiquantitative geochemical or isotopic tools based on a restricted number of variables. However, a more complete and quantitative view could be reached applying multivariate analysis, mass balance techniques, and statistical tests. As an example, in this work a statistical and quantitative scheme is applied to analyze the geochemical features for the Sierra de las Cruces (SC volcanic range (Mexican Volcanic Belt. In this locality, the volcanic activity (3.7 to 0.5 Ma was dominantly dacitic, but the presence of spheroidal andesitic enclaves and/or diverse disequilibrium features in majority of lavas confirms the operation of magma mixing/mingling. New discriminant-function-based multidimensional diagrams were used to discriminate tectonic setting. Statistical tests of discordancy and significance were applied to evaluate the influence of the subducting Cocos plate, which seems to be rather negligible for the SC magmas in relation to several major and trace elements. A cluster analysis following Ward’s linkage rule was carried out to classify the SC volcanic rocks geochemical groups. Finally, two mass-balance schemes were applied for the quantitative evaluation of the proportion of the end-member components (dacitic and andesitic magmas in the comingled lavas (binary mixtures.

  1. Consciousness extended

    DEFF Research Database (Denmark)

    Carrara-Augustenborg, Claudia

    2012-01-01

    of neural thresholds distinguishes the unfolding of the informational broadcast from the emergence of subjective awareness. In such sense, I conceptualize consciousness as a phenomenon unfolding along a continuum, ranging from complete inaccessibility to full awareness. The proposal presented......There is no consensus yet regarding a conceptualization of consciousness able to accommodate all the features of such complex phenomenon. Different theoretical and empirical models lend strength to both the occurrence of a non-accessible informational broadcast, and to the mobilization of specific...... brain areas responsible for the emergence of the individual´s explicit and variable access to given segments of such broadcast. Rather than advocating one model over others, this chapter proposes to broaden the conceptualization of consciousness by letting it embrace both mechanisms. Within...

  2. The immediate effects of two manual therapy techniques on ankle musculoarticular stiffness and dorsiflexion range of motion in people with chronic ankle rigidity: A randomized clinical trial.

    Science.gov (United States)

    Hidalgo, Benjamin; Hall, Toby; Berwart, Mathilde; Biernaux, Elinor; Detrembleur, Christine

    2017-12-29

    Ankle rigidity is a common musculoskeletal disorder affecting the talocrural joint, which can impair weight-bearing ankle dorsiflexion (WBADF) and daily-life in people with or without history of ankle injuries. Our objective was to compare the immediate effects of efficacy of Mulligan Mobilization with Movement (MWM) and Osteopathic Mobilization (OM) for improving ankle dorsiflexion range of motion (ROM) and musculoarticular stiffness (MAS) in people with chronic ankle dorsiflexion rigidity. A randomized clinical trial with two arms. Patients were recruited by word of mouth and via social network as well as posters, and analyzed in the neuro musculoskeletal laboratory of the "Université Catholique de Louvain-la-Neuve", Brussels, Belgium. 67 men (aged 18-40 years) presenting with potential chronic non-specific and unilateral ankle mobility deficit during WBDF were assessed for eligibility and finally 40 men were included and randomly allocated to single session of either MWM or OM. Two modalities of manual therapy indicated for hypothetic immediate effects in chronic ankle dorsiflexion stiffness, i.e. MWM and OM, were applied during a single session on included patients. Comprised blinding measures of MAS with a specific electromechanical device (namely: Lehmann's device) producing passive oscillatory ankle joint dorsiflexion and with clinical measures of WBADF-ROM as well. A two-way ANOVA revealed a non-significant interaction between both techniques and time for all outcome measures. For measures of MAS: elastic-stiffness (p= 0.37), viscous-stiffness (p= 0.83), total-stiffness (p= 0.58). For WBADF-ROM: toe-wall distance (p= 0.58) and angular ROM (p= 0.68). Small effect sizes between groups were determined with Cohen's d ranging from 0.05 to 0.29. One-way ANOVA demonstrated non-significant difference and small to moderate effects sizes (d= 0.003-0.58) on all outcome measures before and after interventions within both groups. A second two-way ANOVA analyzed the

  3. Once-daily dosing is appropriate for extended-release divalproex over a wide dose range, but not for enteric-coated, delayed-release divalproex : Evidence via computer simulations and implications for epilepsy therapy

    NARCIS (Netherlands)

    Reed, Ronald Charles; Dutta, Sandeep; Liu, Wei

    2009-01-01

    Divalproex sodium extended-release (divalproex-ER), administered once-daily, maintains plasma valproic acid (VPA) concentrations for 24 h, whereas enteric-coated, delayed-release divalproex sodium (divalproex) requires multiple-daily doses to do the same. We hypothesize that a once-daily divalproex

  4. Myofascial techniques: What are their effects on joint range of motion and pain? - A systematic review and meta-analysis of randomised controlled trials.

    Science.gov (United States)

    Webb, Tamsyn R; Rajendran, Dévan

    2016-07-01

    This systematic review aimed to determine the evidence for the effect of a single manually applied myofascial technique (MFT) on joint range of motion (JROM) and pain in non-pathological symptomatic subjects. Authors independently searched the following databases: PEDro; Cochrane Library; NLM PubMed; EMBASE; Academic Search Premier; MEDLINE; Psychology and Behavioural Sciences Collection; PsycINFO; SPORTSDiscus; CINAHL Plus from 2003 to 2015. All randomised controlled trials (RCTs) that used JROM as an outcome measure were identified. RCT quality was independently evaluated using PEDro and Cochrane Risk of Bias tools and all reported outcome data were independently abstracted and presented. If post-intervention central tendencies and variance were reported, these were assessed for heterogeneity with a view to performing a meta-analysis. Nine RCTs (n = 534) were systematically reviewed and outcome data presented; all trials concluded that MFT increased JROM and reduced pain levels in symptomatic patients. Two RCTs (n = 161) were judged 'moderately' heterogeneous (I(2) = 47.2%; Cochran's Q = 5.69; p = 0.128, df = 3) and meta-analysis using a fixed effects model suggested a 'moderate' effect size of MFTs on jaw opening (ES = 0.578; 95%CI 0.302 to 0.853). Although results reported by each RCT indicate that MFT increases JROM and reduces pain scores, there are a number of threats that challenge the statistical inferences underpinning these findings. Only two trials could be meta-analysed, the results of which suggest that applying MFTs to symptomatic patients diagnosed with latent trigger-points in masseter muscle can increase jaw JROM. Copyright © 2016 Elsevier Ltd. All rights reserved.

  5. Extended memory management under RTOS

    Science.gov (United States)

    Plummer, M.

    1981-01-01

    A technique for extended memory management in ROLM 1666 computers using FORTRAN is presented. A general software system is described for which the technique can be ideally applied. The memory manager interface with the system is described. The protocols by which the manager is invoked are presented, as well as the methods used by the manager.

  6. Simplified loss analysis and comparison of full-bridge, full-range ...

    Indian Academy of Sciences (India)

    The loss of zero-voltage-switching (ZVS) of active switches has been a serious limitation of full-bridge (FBZVS) converters. Many techniques have been proposed in the past to extend the range of ZVS operation over the wider and also the full range of operation. However, in these techniques ZVS is achieved at the expense ...

  7. Extending the Binomial Checkpointing Technique for Resilience

    Energy Technology Data Exchange (ETDEWEB)

    Walther, Andrea; Narayanan, Sri Hari Krishna

    2016-10-10

    In terms of computing time, adjoint methods offer a very attractive alternative to compute gradient information, re- quired, e.g., for optimization purposes. However, together with this very favorable temporal complexity result comes a memory requirement that is in essence proportional with the operation count of the underlying function, e.g., if algo- rithmic differentiation is used to provide the adjoints. For this reason, checkpointing approaches in many variants have become popular. This paper analyzes an extension of the so-called binomial approach to cover also possible failures of the computing systems. Such a measure of precaution is of special interest for massive parallel simulations and adjoint calculations where the mean time between failure of the large scale computing system is smaller than the time needed to complete the calculation of the adjoint information. We de- scribe the extensions of standard checkpointing approaches required for such resilience, provide a corresponding imple- mentation and discuss numerical results.

  8. Two mass-spectrometric techniques for quantifying serine enantiomers and glycine in cerebrospinal fluid : potential confounders and age-dependent ranges

    NARCIS (Netherlands)

    Fuchs, Sabine A; de Sain-van der Velden, Monique G M; de Barse, Martina M J; Roeleveld, Martin W; Hendriks, Margriet; Dorland, Lambertus; Klomp, Leo W J; Berger, Ruud; de Koning, Tom J

    BACKGROUND: The recent discovery and specific functions of D-amino acids in humans are bound to lead to the revelation of D-amino acid abnormalities in human disorders. Therefore, high-throughput analysis techniques are warranted to determine D-amino acids in biological fluids in a routine

  9. TU-CD-304-01: FEATURED PRESENTATION and BEST IN PHYSICS (THERAPY): Trajectory Modulated Arc Therapy: Development of Novel Arc Delivery Techniques Integrating Dynamic Table Motion for Extended Volume Treatments

    Energy Technology Data Exchange (ETDEWEB)

    Chin, E; Hoppe, R; Million, L; Loo, B; Koong, A; Xing, L; Hsu, A; Fahimian, B [Stanford University, Stanford, CA (United States); Otto, K [University of British Columbia, Vancouver, BC (Canada)

    2015-06-15

    Purpose: Integration of coordinated robotic table motion with inversely-planned arc delivery has the potential to resolve table-top delivery limitations of large-field treatments such as Total Body Irradiation (TBI), Total Lymphoid Irradiation (TLI), and Cranial-Spinal Irradiation (CSI). We formulate the foundation for Trajectory Modulated Arc Therapy (TMAT), and using Varian Developer Mode capabilities, experimentally investigate its practical implementation for such techniques. Methods: A MATLAB algorithm was developed for inverse planning optimization of the table motion, MLC positions, and gantry motion under extended-SSD geometry. To maximize the effective field size, delivery trajectories for TMAT TBI were formed with the table rotated at 270° IEC and dropped vertically to 152.5cm SSD. Preliminary testing of algorithm parameters was done through retrospective planning analysis. Robotic delivery was programmed using custom XML scripting on the TrueBeam Developer Mode platform. Final dose was calculated using the Eclipse AAA algorithm. Initial verification of delivery accuracy was measured using OSLDs on a solid water phantom of varying thickness. Results: A comparison of DVH curves demonstrated that dynamic couch motion irradiation was sufficiently approximated by static control points spaced in intervals of less than 2cm. Optimized MLC motion decreased the average lung dose to 68.5% of the prescription dose. The programmed irradiation integrating coordinated table motion was deliverable on a TrueBeam STx linac in 6.7 min. With the couch translating under an open 10cmx20cm field angled at 10°, OSLD measurements along the midline of a solid water phantom at depths of 3, 5, and 9cm were within 3% of the TPS AAA algorithm with an average deviation of 1.2%. Conclusion: A treatment planning and delivery system for Trajectory Modulated Arc Therapy of extended volumes has been established and experimentally demonstrated for TBI. Extension to other treatment

  10. Frequency Estimation Techniques For High Dynamic Trajectories

    Science.gov (United States)

    Vilnrotter, V. A.; Hinedi, S. M.; Kumar, R.

    1989-01-01

    Report presents comparative study of four techniques for estimating frequency of sinusoidal signal received in presence of noise when transmitter and/or receiver experiencing very high dynamics. Four techniques involve approximate-maximum-likelihood estimator, extended Kalman filter, cross-product automatic frequency control loop, and digital phase locked loop, respectively. In numerical simulations, each technique applied to signal from transmitter maneuvering along common trajectory; performance of each examined to determine its useful operating range, and performances compared.

  11. Telluric and D.C. Resistivity Techniques Applied to the Geophysical Investigation of Basin and Range Geothermal Systems, Part III: The Analysis of Data From Grass Valley, Nevada

    Energy Technology Data Exchange (ETDEWEB)

    Beyer, J. H. [Univ. of California, Berkeley, CA (United States)

    1977-06-01

    This paper contains a detailed interpretation of E-field ratio telluric, bipole-dipole resistivity mapping, and dipole-dipole resistivity data obtained in the course of geophysical exploration of the Leach Hot Springs area of Grass Valley, Nevada. Several areas are singled out as being worthy of further investigation of their geothermal potential. Comparison of the three electrical exploration techniques indicates that: the bipole-dipole resistivity mapping method is the least useful; the dipole-dipole resistivity method can be very useful, but is, for practical purposes, exceptionally expensive and difficult to interpret; the E-field ratio telluric method can be a highly successful reconnaissance technique for delineating structures and relating the resistivities of different regions within the survey area.

  12. Telluric and D. C. resistivity techniques applied to the geophysical investigation of basin and range geothermal systems. Part III. The analysis of data from Grass Valley, Nevada

    Energy Technology Data Exchange (ETDEWEB)

    Beyer, J.H.

    1977-06-01

    A detailed interpretation is presented of E-field ratio telluric, bipole-dipole resistivity mapping, and dipole-dipole resistivity data obtained in the course of geophysical exploration of the Leach Hot Springs area of Grass Valley, Nevada. Several areas are singled out as being worthy of further investigation of their geothermal potential. Comparison of the three electrical exploration techniques indicates that: the bipole-dipole resistivity mapping method is the least useful; the dipole-dipole resistivity method can be very useful, but is, for practical purposes, exceptionally expensive and difficult to interpret; the E-field ratio telluric method can be a highly successful reconnaissance technique for delineating structures and relating the resistivities of different regions within the survey area.

  13. LONG-TERM CONSERVATION OF PROTOCORMS OF Brassavola nodosa (L) LIND. (ORCHIDACEAE): EFFECT OF ABA AND A RANGE OF CRYOCONSERVATION TECHNIQUES.

    Science.gov (United States)

    Mata-Rosas, M; Lastre-Puertos, E

    2015-01-01

    Populations of Brassavola nodosa have been severely affected by habitat destruction and illegal collecting, and as with the majority of orchid species, it is critical to take action to guarantee their continued survival. The present study aimed to establish protocols for the long-term conservation of protocorms of species. Four different cryogenic techniques were compared: encapsulation-dehydration (ED), encapsulation-vitrification (EV), encapsulation-dehydration-vitrification (EDV) and vitrification. Preculture of protocorms with ABA was a critical factor in obtaining high percentages of regrowth. With vitrification, 100% regrowth was achieved in five treatments, mainly when protocorms were dehydrated with PVS2 for 120 min. 100% regrowth was also obtained with EDV, where the protocorms were precultured with ABA 5 mg/l for 3 days and incubated with PVS2 for 60 min. With the ED, regrowth of 72% was achieved with the preculture of protocorms with ABA 5 mg/l for the three times of incubation used (3, 6 and 9 days). In the case of EV, 92% regrowth, was recorded when protocorms were precultured for 9 days with ABA 3 mg/l and incubated with PVS2 for 90 min. Although regrowth of protocorms was obtained with all the techniques used, the vitrification technique is preferred since it requires less labour and is less costly.

  14. Feasibility of gamma irradiation as a stabilisation technique in the preparation of tissue reference materials for a range of shellfish toxins.

    Science.gov (United States)

    McCarron, Pearse; Kotterman, Michiel; de Boer, Jacob; Rehmann, Nils; Hess, Philipp

    2007-04-01

    The effect of gamma-irradiation on concentrations of hydrophilic and lipophilic phycotoxins has been investigated by use of HPLC-UV and LC-MS. Pure toxins in organic solvents and toxins in mussel (Mytilus edulis) tissues were irradiated at three different doses. In solution all toxin concentrations were reduced to some extent. Most severe decreases were observed for domoic acid and yessotoxin, for which the smallest dose of irradiation led to almost complete destruction. For pectenotoxin-2 the decrease in concentration was less severe but still continuous with increasing dose. Azaspiracid-1 and okadaic acid were the least affected in solution. In shellfish tissue the decrease in toxin concentrations was much reduced compared with the effect in solution. After irradiation at the highest dose reductions in concentrations were between ca. 5 and 20% for the lipophilic toxins and there was no statistical difference between control and irradiated samples for azaspiracids in tissue. Irradiation of shellfish tissues contaminated with domoic acid led to a more continuous decrease in the amount of the toxin with increasing dose. The effect of irradiation on the viability of microbial activity in shellfish tissues was assessed by using total viable counting techniques. Microbial activity depended on the type of shellfish and on the pretreatment of the shellfish tissues (with or without heat treatment). As far as we are aware this is the first investigation of the effectiveness of irradiation as a technique for stabilising tissue reference materials for determination of phycotoxins. Our results suggest that this technique is not effective for materials containing domoic acid. It does, however, merit further investigation as a stabilisation procedure for preparation of shellfish tissue materials for some lipophilic toxins, in particular azaspiracids. Chemical structures of the toxins investigated in the study.

  15. Note: Vectorial-magneto optical Kerr effect technique combined with variable temperature and full angular range all in a single setup

    Science.gov (United States)

    Cuñado, Jose Luis F.; Pedrosa, Javier; Ajejas, Fernando; Bollero, Alberto; Perna, Paolo; Teran, Francisco J.; Miranda, Rodolfo; Camarero, Julio

    2015-04-01

    Here, we report on a versatile full angular resolved/broad temperature range/vectorial magneto optical Kerr effect (MOKE) magnetometer, named TRISTAN. Its versatility relies on its capacity to probe temperature and angular dependencies of magnetization reversal processes without the need to do any intervention on the apparatus during measurements. The setup is a combination of a vectorial MOKE bench and a cryostat with optical access. The cryostat has a motorized rotatable sample holder with azimuthal correction. It allows for simultaneous and quantitative acquisition of the two in-plane magnetization components during the hysteresis loop at different temperatures from 4 K up to 500 K and in the whole angular range, without neither changing magnet orientation nor opening the cryostat. Measurements performed in a model system with competing collinear biaxial and uniaxial contributions are presented to illustrate its capabilities.

  16. Note: Vectorial-magneto optical Kerr effect technique combined with variable temperature and full angular range all in a single setup.

    Science.gov (United States)

    Cuñado, Jose Luis F; Pedrosa, Javier; Ajejas, Fernando; Bollero, Alberto; Perna, Paolo; Teran, Francisco J; Miranda, Rodolfo; Camarero, Julio

    2015-04-01

    Here, we report on a versatile full angular resolved/broad temperature range/vectorial magneto optical Kerr effect (MOKE) magnetometer, named TRISTAN. Its versatility relies on its capacity to probe temperature and angular dependencies of magnetization reversal processes without the need to do any intervention on the apparatus during measurements. The setup is a combination of a vectorial MOKE bench and a cryostat with optical access. The cryostat has a motorized rotatable sample holder with azimuthal correction. It allows for simultaneous and quantitative acquisition of the two in-plane magnetization components during the hysteresis loop at different temperatures from 4 K up to 500 K and in the whole angular range, without neither changing magnet orientation nor opening the cryostat. Measurements performed in a model system with competing collinear biaxial and uniaxial contributions are presented to illustrate its capabilities.

  17. Angle-resolved photoemission extended fine structure

    Energy Technology Data Exchange (ETDEWEB)

    Barton, J.J.

    1985-03-01

    Measurements of the Angle-Resolved Photoemission Extended Fine Structure (ARPEFS) from the S(1s) core level of a c(2 x 2)S/Ni(001) are analyzed to determine the spacing between the S overlayer and the first and second Ni layers. ARPEFS is a type of photoelectron diffraction measurement in which the photoelectron kinetic energy is swept typically from 100 to 600 eV. By using this wide range of intermediate energies we add high precision and theoretical simplification to the advantages of the photoelectron diffraction technique for determining surface structures. We report developments in the theory of photoelectron scattering in the intermediate energy range, measurement of the experimental photoemission spectra, their reduction to ARPEFS, and the surface structure determination from the ARPEFS by combined Fourier and multiple-scattering analyses. 202 refs., 67 figs., 2 tabs.

  18. Seeded free-electron and inverse free-electron laser techniques for radiation amplification and electron microbunching in the terahertz range

    Directory of Open Access Journals (Sweden)

    C. Sung

    2006-12-01

    Full Text Available A comprehensive analysis is presented that describes amplification of a seed THz pulse in a single-pass free-electron laser (FEL driven by a photoinjector. The dynamics of the radiation pulse and the modulated electron beam are modeled using the time-dependent FEL code, GENESIS 1.3. A 10-ps (FWHM electron beam with a peak current of 50–100 A allows amplification of a ∼1  kW seed pulse in the frequency range 0.5–3 THz up to 10–100 MW power in a relatively compact 2-m long planar undulator. The electron beam driving the FEL is strongly modulated, with some inhomogeneity due to the slippage effect. It is shown that THz microbunching of the electron beam is homogeneous over the entire electron pulse when saturated FEL amplification is utilized at the very entrance of an undulator. This requires seeding of a 30-cm long undulator buncher with a 1–3 MW of pump power with radiation at the resonant frequency. A narrow-band seed pulse in the THz range needed for these experiments can be generated by frequency mixing of CO_{2} laser lines in a GaAs nonlinear crystal. Two schemes for producing MW power pulses in seeded FELs are considered in some detail for the beam parameters achievable at the Neptune Laboratory at UCLA: the first uses a waveguide to transport radiation in the 0.5–3 THz range through a 2-m long FEL amplifier and the second employs high-gain third harmonic generation using the FEL process at 3–9 THz.

  19. Exact tensor hypercontraction: a universal technique for the resolution of matrix elements of local finite-range N-body potentials in many-body quantum problems.

    Science.gov (United States)

    Parrish, Robert M; Hohenstein, Edward G; Schunck, Nicolas F; Sherrill, C David; Martínez, Todd J

    2013-09-27

    Configuration-space matrix elements of N-body potentials arise naturally and ubiquitously in the Ritz-Galerkin solution of many-body quantum problems. For the common specialization of local, finite-range potentials, we develop the exact tensor hypercontraction method, which provides a quantized renormalization of the coordinate-space form of the N-body potential, allowing for a highly separable tensor factorization of the configuration-space matrix elements. This representation allows for substantial computational savings in chemical, atomic, and nuclear physics simulations, particularly with respect to difficult "exchangelike" contractions.

  20. Silicone chain extender

    DEFF Research Database (Denmark)

    2015-01-01

    The present invention relates to a silicone chain extender, more particularly a chain extender for silicone polymers and copolymers, to a chain extended silicone polymer or copolymer and to a functionalized chain extended silicone polymer or copolymer, to a method for the preparation thereof...

  1. Processing of Nanostructured Devices Using Microfabrication Techniques

    Science.gov (United States)

    Hunter, Gary W (Inventor); Xu, Jennifer C (Inventor); Evans, Laura J (Inventor); Kulis, Michael H (Inventor); Berger, Gordon M (Inventor); Vander Wal, Randall L (Inventor)

    2014-01-01

    Systems and methods that incorporate nanostructures into microdevices are discussed herein. These systems and methods can allow for standard microfabrication techniques to be extended to the field of nanotechnology. Sensors incorporating nanostructures can be fabricated as described herein, and can be used to reliably detect a range of gases with high response.

  2. An algebraic approach to symmetric extended formulations

    OpenAIRE

    Braun, Gábor; Pokutta, Sebastian

    2012-01-01

    Extended formulations are an important tool to obtain small (even compact) formulations of polytopes by representing them as projections of higher dimensional ones. It is an important question whether a polytope admits a small extended formulation, i.e., one involving only a polynomial number of inequalities in its dimension. For the case of symmetric extended formulations (i.e., preserving the symmetries of the polytope) Yannakakis established a powerful technique to derive lower bounds and ...

  3. Proposal and verification numerical simulation for a microwave forward scattering technique at upper hybrid resonance for the measurement of electron gyroscale density fluctuations in the electron cyclotron frequency range in magnetized plasmas

    Science.gov (United States)

    Kawamori, E.; Igami, H.

    2017-11-01

    A diagnostic technique for detecting the wave numbers of electron density fluctuations at electron gyro-scales in an electron cyclotron frequency range is proposed, and the validity of the idea is checked by means of a particle-in-cell (PIC) numerical simulation. The technique is a modified version of the scattering technique invented by Novik et al. [Plasma Phys. Controlled Fusion 36, 357-381 (1994)] and Gusakov et al., [Plasma Phys. Controlled Fusion 41, 899-912 (1999)]. The novel method adopts forward scattering of injected extraordinary probe waves at the upper hybrid resonance layer instead of the backward-scattering adopted by the original method, enabling the measurement of the wave-numbers of the fine scale density fluctuations in the electron-cyclotron frequency band by means of phase measurement of the scattered waves. The verification numerical simulation with the PIC method shows that the technique has a potential to be applicable to the detection of electron gyro-scale fluctuations in laboratory plasmas if the upper-hybrid resonance layer is accessible to the probe wave. The technique is a suitable means to detect electron Bernstein waves excited via linear mode conversion from electromagnetic waves in torus plasma experiments. Through the numerical simulations, some problems that remain to be resolved are revealed, which include the influence of nonlinear processes such as the parametric decay instability of the probe wave in the scattering process, and so on.

  4. Exclusion Bounds for Extended Anyons

    Science.gov (United States)

    Larson, Simon; Lundholm, Douglas

    2017-08-01

    We introduce a rigorous approach to the many-body spectral theory of extended anyons, that is quantum particles confined to two dimensions that interact via attached magnetic fluxes of finite extent. Our main results are many-body magnetic Hardy inequalities and local exclusion principles for these particles, leading to estimates for the ground-state energy of the anyon gas over the full range of the parameters. This brings out further non-trivial aspects in the dependence on the anyonic statistics parameter, and also gives improvements in the ideal (non-extended) case.

  5. Extending the range of turbidity measurement using polarimetry

    Energy Technology Data Exchange (ETDEWEB)

    Baba, Justin S.

    2017-11-21

    Turbidity measurements are obtained by directing a polarized optical beam to a scattering sample. Scattered portions of the beam are measured in orthogonal polarization states to determine a scattering minimum and a scattering maximum. These values are used to determine a degree of polarization of the scattered portions of the beam, and concentrations of scattering materials or turbidity can be estimated using the degree of polarization. Typically, linear polarizations are used, and scattering is measured along an axis that orthogonal to the direction of propagation of the polarized optical beam.

  6. Long-range attractive forces extending from alumina nanofiber surface

    Directory of Open Access Journals (Sweden)

    Leonid A. Kaledin

    2014-07-01

    Full Text Available Aluminum oxide-hydroxide nanofibers, 2 nm in diameter and approximately 250 nm long, are electroadhesively grafted onto glass microfibers, therefore forming a macroscopic assembly of alumina nanofibers on the second solid in highly organized matter. The assembly can be viewed as a straight cylinder with rough surface and charge density of approximately 0.08 C/m2. This creates a significant electric field with negligible screening (ka ≪ 1 in the region close to the surface of the assemblies. This field attracts nano- and micron-size particles from as far as 0.3 mm in less than a few seconds, many orders of magnitude greater than the conventional Derjaguin–Landau–Verwey–Overbeek theory that predicts only nanometer-scale effects arising from the presence of the surface. The strong electric field on the surface is then able to retain particles such as micron-size powdered activated carbon as well as much smaller particles such as fumed silica nanoparticles of 10–15 nm in diameter, viruses, atomically thick sheets of graphene oxide, latex spheres, RNA, DNA, proteins, and dyes.

  7. Extending the range of linear scheduling in highway construction

    OpenAIRE

    Bafna, Tarun

    1991-01-01

    Linear Scheduling Method is a powerful graphical scheduling method which is best suited for scheduling projects involving repetitive activities. Highway construction projects are excellent examples of projects displaying repetitive characteristics. The research explores usefulness of linear scheduling in highway construction. The Linear Scheduling Method (LSM) was implemented in the field to schedule highway projects. Problems encountered during the field experience were studied and res...

  8. Hybrid Direct Drive PPU with Extended Operating Range Project

    Data.gov (United States)

    National Aeronautics and Space Administration — High-power electric propulsion with Hall thrusters has been proposed as a strong candidate for Electric Path missions, but conventional power processing units (PPUs)...

  9. Extending the range for force calibration in magnetic tweezers.

    Science.gov (United States)

    Daldrop, Peter; Brutzer, Hergen; Huhle, Alexander; Kauert, Dominik J; Seidel, Ralf

    2015-05-19

    Magnetic tweezers are a wide-spread tool used to study the mechanics and the function of a large variety of biomolecules and biomolecular machines. This tool uses a magnetic particle and a strong magnetic field gradient to apply defined forces to the molecule of interest. Forces are typically quantified by analyzing the lateral fluctuations of the biomolecule-tethered particle in the direction perpendicular to the applied force. Since the magnetic field pins the anisotropy axis of the particle, the lateral fluctuations follow the geometry of a pendulum with a short pendulum length along and a long pendulum length perpendicular to the field lines. Typically, the short pendulum geometry is used for force calibration by power-spectral-density (PSD) analysis, because the movement of the bead in this direction can be approximated by a simple translational motion. Here, we provide a detailed analysis of the fluctuations according to the long pendulum geometry and show that for this direction, both the translational and the rotational motions of the particle have to be considered. We provide analytical formulas for the PSD of this coupled system that agree well with PSDs obtained in experiments and simulations and that finally allow a faithful quantification of the magnetic force for the long pendulum geometry. We furthermore demonstrate that this methodology allows the calibration of much larger forces than the short pendulum geometry in a tether-length-dependent manner. In addition, the accuracy of determination of the absolute force is improved. Our force calibration based on the long pendulum geometry will facilitate high-resolution magnetic-tweezers experiments that rely on short molecules and large forces, as well as highly parallelized measurements that use low frame rates. Copyright © 2015 Biophysical Society. Published by Elsevier Inc. All rights reserved.

  10. Evolving trends in cryopreservation and parameters influencing semen extender preparation - a prospective review.

    Science.gov (United States)

    Sridharan, T B; Vickram, A S

    2016-01-01

    Cryopreservation is a technique by which, semen can be preserved to subzero temperature, usually at -196° C. The freezing of semen desires vitrification mediators that diminish wreck to the cells (spermatozoan) during the freeze and thaw process. Using cryopreservation, the quality of the semen has been increased in the latest years, by which the achievement rate for the insemination techniques has increased in an agreed way. The area need to be focused is to enhance the quality of the semen extender preparation before cryopreservation. Many researchers are working in the area of cryopreservation of human semen with different semen extenders. Several parameters influence the properties of semen extender essential for better post thaw results. This review is mainly focused on a range of parameters which influence the best semen extender for cryopreservation that includes glycerol and its importance, buffer and novel usage of antimicrobial peptides as antimicrobial agents.

  11. On Range of Skill

    DEFF Research Database (Denmark)

    Hansen, Thomas Dueholm; Miltersen, Peter Bro; Sørensen, Troels Bjerre

    2008-01-01

    size (and doubly exponential in its depth). We also provide techniques that yield concrete bounds for unbalanced game trees and apply these to estimate the Range of Skill of Tic-Tac-Toe and Heads-Up Limit Texas Hold'em Poker. In particular, we show that the Range of Skill of Tic-Tac-Toe is more than...

  12. Extended icosahedral structures

    CERN Document Server

    Jaric, Marko V

    1989-01-01

    Extended Icosahedral Structures discusses the concepts about crystal structures with extended icosahedral symmetry. This book is organized into six chapters that focus on actual modeling of extended icosahedral crystal structures. This text first presents a tiling approach to the modeling of icosahedral quasiperiodic crystals. It then describes the models for icosahedral alloys based on random connections between icosahedral units, with particular emphasis on diffraction properties. Other chapters examine the glassy structures with only icosahedral orientational order and the extent of tra

  13. Validation of multiple diagnostic techniques to detect Cryptosporidium sp. and Giardia sp. in free-ranging western lowland gorillas (Gorilla gorilla gorilla) and observations on the prevalence of these protozoan infections in two populations in Gabon.

    Science.gov (United States)

    van Zijll Langhout, Martine; Reed, Patricia; Fox, Mark

    2010-06-01

    Anthropozoonotic diseases threaten the survival of western lowland gorillas (Gorilla gorilla gorilla). Use of accurate diagnostic techniques in gorilla health monitoring contributes to the conservation of gorillas by providing robust information for appropriate management decisions. To identify suitable protozoa diagnostic techniques for wild gorillas, 95 fecal specimens were collected in Lopé National Park and east of Moukalaba-Doudou National Park in Gabon, areas with high and low levels of human activity, respectively. The samples were examined for Cryptosporidium sp. and Giardia sp. by using the following diagnostic techniques: a commercially available immunofluorescent antibody test kit, Merifluor, and a rapid immune-assay, ImmunoCard STAT!, to detect Cryptosporidium sp. and Giardia sp., and a modified Ziehl-Neelsen stain to detect Cryptosporidium sp. oocysts. The results obtained from the Merifluor test, considered the "gold standard" in human studies, were used to estimate the prevalence of Cryptosporidium sp. and Giardia sp. infections in Lopé National Park (19.0% and 22.6%, respectively) and east of Moukalaba-Doudou National Park (0% and 9.1%, respectively). The difference in prevalence in both areas may be associated with differing levels of anthropogenic disturbance. The sensitivity and specificity of the latter two diagnostic techniques were calculated by using the Merifluor test as a control. The ImmunoCard STAT! was found suitable for Giardia sp. antigen detection (specific but not sensitive) and inappropriate for Cryptosporidium sp. antigen detection (not specific or sensitive). The modified Ziehl-Neelsen stain was found to be highly specific but not sensitive in the detection of Cryptosporidium sp. oocysts. These results underline the necessity of using ancillary tests and concentration methods to correctly identify positive samples. This is the first report of Cryptosporidium sp. and Giardia sp. infections in free-ranging western lowland gorillas

  14. Affinity Propagation Clustering of Measurements for Multiple Extended Target Tracking

    National Research Council Canada - National Science Library

    Zhang, Tao; Wu, Renbiao

    2015-01-01

    .... In this paper, affinity propagation clustering is introduced into measurement partitioning for extended target tracking, and the elliptical gating technique is used to remove the clutter measurements...

  15. Rational extended thermodynamics

    CERN Document Server

    Müller, Ingo

    1998-01-01

    Ordinary thermodynamics provides reliable results when the thermodynamic fields are smooth, in the sense that there are no steep gradients and no rapid changes. In fluids and gases this is the domain of the equations of Navier-Stokes and Fourier. Extended thermodynamics becomes relevant for rapidly varying and strongly inhomogeneous processes. Thus the propagation of high­ frequency waves, and the shape of shock waves, and the regression of small-scale fluctuation are governed by extended thermodynamics. The field equations of ordinary thermodynamics are parabolic while extended thermodynamics is governed by hyperbolic systems. The main ingredients of extended thermodynamics are • field equations of balance type, • constitutive quantities depending on the present local state and • entropy as a concave function of the state variables. This set of assumptions leads to first order quasi-linear symmetric hyperbolic systems of field equations; it guarantees the well-posedness of initial value problems and f...

  16. Extended defects in Germanium

    CERN Document Server

    Osgood, R M

    2008-01-01

    Intends to provide a fundamental understanding of the extended-defect formation during Ge materials and device processing, providing ways to distinguish harmful from less detrimental defects and should point out ways for defect engineering and control.

  17. Theater Missile Defense Extended Test Range Supplemental Environmental Impact Statement - Eglin Gulf Test Range. Volume 2

    Science.gov (United States)

    1998-07-01

    Boatsafe, 1998. BoatSafe.com and Boat Safe Kids , [Online]. Available: http://www.boatsafe.com, [9 June]. Bohnsack, J. A., D.E. Harper, and D.B...Florida, and Gary Cornell, EDAW, Inc., regarding unique visual features of the Florida Keys, 4 February. Kochman, H.I., 1978. “Eastern Indigo Snake...Exercise: “Standard EIGER” (U), N00014-94-C-0061, 27 July. Steiner, T.M., O.L. Bass, Jr., and J.A. Kushlan, 1983. Status of the Eastern Indigo Snake

  18. Extended Hamiltonian approach to continuous tempering.

    Science.gov (United States)

    Gobbo, Gianpaolo; Leimkuhler, Benedict J

    2015-06-01

    We introduce an enhanced sampling simulation technique based on continuous tempering, i.e., on continuously varying the temperature of the system under investigation. Our approach is mathematically straightforward, being based on an extended Hamiltonian formulation in which an auxiliary degree of freedom, determining the effective temperature, is coupled to the physical system. The physical system and its temperature evolve continuously in time according to the equations of motion derived from the extended Hamiltonian. Due to the Hamiltonian structure, it is easy to show that a particular subset of the configurations of the extended system is distributed according to the canonical ensemble for the physical system at the correct physical temperature.

  19. An extended day program

    Directory of Open Access Journals (Sweden)

    Ševkušić-Mandić Slavica G.

    2002-01-01

    Full Text Available The paper presents the results of a pilot project evaluation, carried out as an action investigation whose aim was to provide a better quality extended day for primary school students. The project included the training of teachers involved in extended day program, designing of special activities performed by teachers with children once a week as well as changes and equipping of premises where children stay. The aims of the program were conception and performance of activities in a less formal way than during regular instructional days, linking of learning at school and acquired knowledge to everyday experiences, and work on contents contributing to the development of child's interests and creativity. The program was accomplished in a Belgrade primary school during the 2001/2002 academic year, comprising students of 1st and 2nd grades (N=77. The effects of the program were monitored throughout the academic year (observation and teachers' reports on accomplished workshops and at the end of the academic year (teachers and students' opinions of the program, academic achievement and creativity of students attending the extended day program compared with students not attending it. Findings about positive effects of the program on students' broadening of interests and willingness to express themselves creatively, indicate unequivocally that there is a need for developing special extended day programs. The extended day program is an opportunity for school to exert greater educational influence that has yet to be tapped.

  20. Extended spider cognition.

    Science.gov (United States)

    Japyassú, Hilton F; Laland, Kevin N

    2017-05-01

    There is a tension between the conception of cognition as a central nervous system (CNS) process and a view of cognition as extending towards the body or the contiguous environment. The centralised conception requires large or complex nervous systems to cope with complex environments. Conversely, the extended conception involves the outsourcing of information processing to the body or environment, thus making fewer demands on the processing power of the CNS. The evolution of extended cognition should be particularly favoured among small, generalist predators such as spiders, and here, we review the literature to evaluate the fit of empirical data with these contrasting models of cognition. Spiders do not seem to be cognitively limited, displaying a large diversity of learning processes, from habituation to contextual learning, including a sense of numerosity. To tease apart the central from the extended cognition, we apply the mutual manipulability criterion, testing the existence of reciprocal causal links between the putative elements of the system. We conclude that the web threads and configurations are integral parts of the cognitive systems. The extension of cognition to the web helps to explain some puzzling features of spider behaviour and seems to promote evolvability within the group, enhancing innovation through cognitive connectivity to variable habitat features. Graded changes in relative brain size could also be explained by outsourcing information processing to environmental features. More generally, niche-constructed structures emerge as prime candidates for extending animal cognition, generating the selective pressures that help to shape the evolving cognitive system.

  1. Airborne Light Detection and Ranging (lidar) Derived Deformation from the MW 6.0 24 August, 2014 South Napa Earthquake Estimated by Two and Three Dimensional Point Cloud Change Detection Techniques

    Science.gov (United States)

    Lyda, A. W.; Zhang, X.; Glennie, C. L.; Hudnut, K.; Brooks, B. A.

    2016-06-01

    Remote sensing via LiDAR (Light Detection And Ranging) has proven extremely useful in both Earth science and hazard related studies. Surveys taken before and after an earthquake for example, can provide decimeter-level, 3D near-field estimates of land deformation that offer better spatial coverage of the near field rupture zone than other geodetic methods (e.g., InSAR, GNSS, or alignment array). In this study, we compare and contrast estimates of deformation obtained from different pre and post-event airborne laser scanning (ALS) data sets of the 2014 South Napa Earthquake using two change detection algorithms, Iterative Control Point (ICP) and Particle Image Velocimetry (PIV). The ICP algorithm is a closest point based registration algorithm that can iteratively acquire three dimensional deformations from airborne LiDAR data sets. By employing a newly proposed partition scheme, "moving window," to handle the large spatial scale point cloud over the earthquake rupture area, the ICP process applies a rigid registration of data sets within an overlapped window to enhance the change detection results of the local, spatially varying surface deformation near-fault. The other algorithm, PIV, is a well-established, two dimensional image co-registration and correlation technique developed in fluid mechanics research and later applied to geotechnical studies. Adapted here for an earthquake with little vertical movement, the 3D point cloud is interpolated into a 2D DTM image and horizontal deformation is determined by assessing the cross-correlation of interrogation areas within the images to find the most likely deformation between two areas. Both the PIV process and the ICP algorithm are further benefited by a presented, novel use of urban geodetic markers. Analogous to the persistent scatterer technique employed with differential radar observations, this new LiDAR application exploits a classified point cloud dataset to assist the change detection algorithms. Ground

  2. AIRBORNE LIGHT DETECTION AND RANGING (LIDAR DERIVED DEFORMATION FROM THE MW 6.0 24 AUGUST, 2014 SOUTH NAPA EARTHQUAKE ESTIMATED BY TWO AND THREE DIMENSIONAL POINT CLOUD CHANGE DETECTION TECHNIQUES

    Directory of Open Access Journals (Sweden)

    A. W. Lyda

    2016-06-01

    Full Text Available Remote sensing via LiDAR (Light Detection And Ranging has proven extremely useful in both Earth science and hazard related studies. Surveys taken before and after an earthquake for example, can provide decimeter-level, 3D near-field estimates of land deformation that offer better spatial coverage of the near field rupture zone than other geodetic methods (e.g., InSAR, GNSS, or alignment array. In this study, we compare and contrast estimates of deformation obtained from different pre and post-event airborne laser scanning (ALS data sets of the 2014 South Napa Earthquake using two change detection algorithms, Iterative Control Point (ICP and Particle Image Velocimetry (PIV. The ICP algorithm is a closest point based registration algorithm that can iteratively acquire three dimensional deformations from airborne LiDAR data sets. By employing a newly proposed partition scheme, “moving window,” to handle the large spatial scale point cloud over the earthquake rupture area, the ICP process applies a rigid registration of data sets within an overlapped window to enhance the change detection results of the local, spatially varying surface deformation near-fault. The other algorithm, PIV, is a well-established, two dimensional image co-registration and correlation technique developed in fluid mechanics research and later applied to geotechnical studies. Adapted here for an earthquake with little vertical movement, the 3D point cloud is interpolated into a 2D DTM image and horizontal deformation is determined by assessing the cross-correlation of interrogation areas within the images to find the most likely deformation between two areas. Both the PIV process and the ICP algorithm are further benefited by a presented, novel use of urban geodetic markers. Analogous to the persistent scatterer technique employed with differential radar observations, this new LiDAR application exploits a classified point cloud dataset to assist the change detection

  3. Extending quantum mechanics entails extending special relativity

    Science.gov (United States)

    Aravinda, S.; Srikanth, R.

    2016-05-01

    The complementarity between signaling and randomness in any communicated resource that can simulate singlet statistics is generalized by relaxing the assumption of free will in the choice of measurement settings. We show how to construct an ontological extension for quantum mechanics (QMs) through the oblivious embedding of a sound simulation protocol in a Newtonian spacetime. Minkowski or other intermediate spacetimes are ruled out as the locus of the embedding by virtue of hidden influence inequalities. The complementarity transferred from a simulation to the extension unifies a number of results about quantum non-locality, and implies that special relativity has a different significance for the ontological model and for the operational theory it reproduces. Only the latter, being experimentally accessible, is required to be Lorentz covariant. There may be certain Lorentz non-covariant elements at the ontological level, but they will be inaccessible at the operational level in a valid extension. Certain arguments against the extendability of QM, due to Conway and Kochen (2009) and Colbeck and Renner (2012), are attributed to their assumption that the spacetime at the ontological level has Minkowski causal structure.

  4. Bounds on Correlation Decay for Long-Range Vector Spin Glasses

    NARCIS (Netherlands)

    Enter, Aernout C.D. van

    1985-01-01

    We give upper bounds on the decay of correlation functions for long-range SO(N)-symmetric spin-glass models in one and two dimensions using McBryan-Spencer techniques. In doing so we extend other's recent results.

  5. Modelling in pinnacle for distance extended source-patient and verification with film EBT2 technique; Modelizacion en pinnacle para tecnica de distancia fuente-paciente extendida y verificacion con peliculas EBT2

    Energy Technology Data Exchange (ETDEWEB)

    Perucha Ortega, M.; Luis simon, J.; Rodriguez Alarcon, C.; Baeza Trujillo, M.; Sanchez Carmona, G.; Vicente Granado, D.; Gutierrez Ramos, S.; Herrador Cordoba, M.

    2013-07-01

    The objective of this work is modelled on the Pinnacle Scheduler the geometry used in our Center for the technique of Total body irradiation which consists of radiate to the patient, whose middle line is 366 cm from the source, in positions lateral decubitus, with 2 fields anteroposterior of 40 x 40 cm{sup 2}, rotated collimator 45 degree centigrade interposing a screen of methacrylate 1 cm thick to 29 cm ahead of the middle line. (Author)

  6. Ampliação da técnica violonística de mão esquerda: um estudo sobre a pestana Extended left-hand guitar technique: a study on the barré

    Directory of Open Access Journals (Sweden)

    Bruno Madeira

    2013-06-01

    Full Text Available A técnica instrumental é um elemento da performance musical em constantes reformulações. Com o objetivo principal de estender a técnica violonística da pestana, o presente artigo foi dividido em três partes: (1 conceituações gerais sobre técnica instrumental; (2 a partir de métodos instrumentais dos últimos quatrocentos anos, um breve histórico da pestana foi delineado com o objetivo de recolher informações técnicas sobre sua realização, (3 sugestões e exemplificações de procedimentos não usuais de pestana (com dedos diferentes do indicador, de falange, bisagra e cruzada, encontrados de forma muito resumida na escassa bibliografia sobre o assunto e cuja aplicabilidade é verificada no repertório.Instrumental technique is an element of musical performance in constant reformulation. With the main objective of expanding the guitar technique of barring, this study was divided into three parts: (1 general concepts about instrumental technique; (2 from instrumental methods of the past four hundred years, a brief history of the barré was outlined in order to collect technical information about its realization, (3 suggestions and examples of unusual barring procedures (with different fingers, phalanx barré, hinge barré, crossed barré, found in the scarce bibliography and which applicability is verified in the repertoire.

  7. Poster Session- Extended Abstracts

    Science.gov (United States)

    Jack D. Alexander III; Jean Findley; Brenda K. Kury; Jan L. Beyers; Douglas S. Cram; Terrell T. Baker; Jon C. Boren; Carl Edminster; Sue A. Ferguson; Steven McKay; David Nagel; Trent Piepho; Miriam Rorig; Casey Anderson; Jeanne Hoadley; Paulette L. Ford; Mark C. Andersen; Ed L. Fredrickson; Joe Truett; Gary W. Roemer; Brenda K. Kury; Jennifer Vollmer; Christine L. May; Danny C. Lee; James P. Menakis; Robert E. Keane; Zhi-Liang Zhu; Carol Miller; Brett Davis; Katharine Gray; Ken Mix; William P. Kuvlesky Jr.; D. Lynn Drawe; Marcia G. Narog; Roger D. Ottmar; Robert E. Vihnanek; Clinton S. Wright; Timothy E. Paysen; Burton K. Pendleton; Rosemary L. Pendleton; Carleton S. White; John Rogan; Doug Stow; Janet Franklin; Jennifer Miller; Lisa Levien; Chris Fischer; Emma Underwood; Robert Klinger; Peggy Moore; Clinton S. Wright

    2008-01-01

    Titles found within Poster Session-Extended Abstracts include:Assessment of emergency fire rehabilitation of four fires from the 2000 fire season on the Vale, Oregon, BLM district: review of the density sampling materials and methods: p. 329 Growth of regreen, seeded for erosion control, in the...

  8. Extending Critical Performativity

    DEFF Research Database (Denmark)

    Spicer, André; Alvesson, Mats; Kärreman, Dan

    2016-01-01

    In this article we extend the debate about critical performativity. We begin by outlining the basic tenets of critical performativity and how this has been applied in the study of management and organization. We then address recent critiques of critical performance. We note these arguments suffer...

  9. Parameterization of extended systems

    DEFF Research Database (Denmark)

    Niemann, Hans Henrik

    2006-01-01

    The YJBK parameterization (of all stabilizing controllers) is extended to handle systems with additional sensors and/or actuators. It is shown that the closed loop transfer function is still an affine function in the YJBK parameters in the nominal case. Further, some closed-loop stability results...

  10. Extended Irreversible Thermodynamics

    CERN Document Server

    Jou, David

    2010-01-01

    This is the 4th edition of the highly acclaimed monograph on Extended Irreversible Thermodynamics, a theory that goes beyond the classical theory of irreversible processes. In contrast to the classical approach, the basic variables describing the system are complemented by non-equilibrium quantities. The claims made for extended thermodynamics are confirmed by the kinetic theory of gases and statistical mechanics. The book covers a wide spectrum of applications, and also contains a thorough discussion of the foundations and the scope of the current theories on non-equilibrium thermodynamics. For this new edition, the authors critically revised existing material while taking into account the most recent developments in fast moving fields such as heat transport in micro- and nanosystems or fast solidification fronts in materials sciences. Several fundamental chapters have been revisited emphasizing physics and applications over mathematical derivations. Also, fundamental questions on the definition of non-equil...

  11. The Fly Printer - Extended

    DEFF Research Database (Denmark)

    Beloff, Laura; Klaus, Malena

    2016-01-01

    Artist talk / Work-in-progress What is the purpose of a machine or an artifact, like the Fly Printer, that is dislocated, that produces images that have no meaning, no instrumentality, that depict nothing in the world? The biological and the cultural are reunited in this apparatus as a possibilit...... the results. The extended version of the Fly Printer containing the technological perception and DNNs is a collaboration between Laura Beloff and Malene Theres Klaus...

  12. The dialogically extended mind

    DEFF Research Database (Denmark)

    Fusaroli, Riccardo; Gangopadhyay, Nivedita; Tylén, Kristian

    2014-01-01

    , we argue that language enhances our cognitive capabilities in a much more radical way: The skilful engagement of public material symbols facilitates evolutionarily unprecedented modes of collective perception, action and reasoning (interpersonal synergies) creating dialogically extended minds. We...... relate our approach to other ideas about collective minds and review a number of empirical studies to identify the mechanisms enabling the constitution of interpersonal cognitive systems....

  13. Extended Theories of Gravitation

    Directory of Open Access Journals (Sweden)

    Fatibene Lorenzo

    2013-09-01

    Full Text Available Within the framework of extended theories of gravitation we shall discuss physical equivalences among different formalisms and classical tests. As suggested by the Ehlers-Pirani-Schild framework, the conformal invariance will be preserved and its effect on observational protocols discussed. Accordingly, we shall review standard tests showing how Palatini f(R-theories naturally passes solar system tests. Observation protocols will be discussed in this wider framework.

  14. Short Communication: Production of extended spectrum beta ...

    African Journals Online (AJOL)

    Multidrug resistant strains of Klebsiella pneumoniae and Escherichia coli constitute a problem in many hospitals. The antibiotic susceptibility profile and the Production of Extended Spetrum Beta-Lactamase (ESBL) of the strains of Klebsiella pneumoniae and Escherichia coli were assessed by the Kirby-Bauer technique and ...

  15. On the scaling range of power-laws originated from fluctuation analysis

    CERN Document Server

    Dariusz, Grech

    2012-01-01

    We extend our previous study of scaling range properties done for detrended fluctuation analysis (DFA) \\cite{former_paper} to other techniques of fluctuation analysis (FA). The new technique called Modified Detrended Moving Average Analysis (MDMA) is introduced and its scaling range properties are examined and compared with those of detrended moving average analysis (DMA) and DFA. It is shown that contrary to DFA, DMA and MDMA techniques exhibit power law dependence of the scaling range with respect to the length of the searched signal and with respect to the accuracy $R^2$ of the fit to the considered scaling law imposed by DMA or MDMA schemes. This power law dependence is satisfied for both uncorrelated and autocorrelated data. We find also a simple generalization of this power law relation for series with different level of autocorrelations measured in terms of the Hurst exponent. Basic relations between scaling ranges for different techniques are also discussed. Our findings should be particularly useful ...

  16. Learning Extended Finite State Machines

    Science.gov (United States)

    Cassel, Sofia; Howar, Falk; Jonsson, Bengt; Steffen, Bernhard

    2014-01-01

    We present an active learning algorithm for inferring extended finite state machines (EFSM)s, combining data flow and control behavior. Key to our learning technique is a novel learning model based on so-called tree queries. The learning algorithm uses the tree queries to infer symbolic data constraints on parameters, e.g., sequence numbers, time stamps, identifiers, or even simple arithmetic. We describe sufficient conditions for the properties that the symbolic constraints provided by a tree query in general must have to be usable in our learning model. We have evaluated our algorithm in a black-box scenario, where tree queries are realized through (black-box) testing. Our case studies include connection establishment in TCP and a priority queue from the Java Class Library.

  17. Cascade Mountain Range in Oregon

    Science.gov (United States)

    Sherrod, David R.

    2016-01-01

    The Cascade mountain system extends from northern California to central British Columbia. In Oregon, it comprises the Cascade Range, which is 260 miles long and, at greatest breadth, 90 miles wide (fig. 1). Oregon’s Cascade Range covers roughly 17,000 square miles, or about 17 percent of the state, an area larger than each of the smallest nine of the fifty United States. The range is bounded on the east by U.S. Highways 97 and 197. On the west it reaches nearly to Interstate 5, forming the eastern margin of the Willamette Valley and, farther south, abutting the Coast Ranges

  18. Current Trends in Satellite Laser Ranging

    Science.gov (United States)

    Pearlman, M. R.; Appleby, G. M.; Kirchner, G.; McGarry, J.; Murphy, T.; Noll, C. E.; Pavlis, E. C.; Pierron, F.

    2010-01-01

    Satellite Laser Ranging (SLR) techniques are used to accurately measure the distance from ground stations to retroreflectors on satellites and the moon. SLR is one of the fundamental techniques that define the international Terrestrial Reference Frame (iTRF), which is the basis upon which we measure many aspects of global change over space, time, and evolving technology. It is one of the fundamental techniques that define at a level of precision of a few mm the origin and scale of the ITRF. Laser Ranging provides precision orbit determination and instrument calibration/validation for satellite-borne altimeters for the better understanding of sea level change, ocean dynamics, ice budget, and terrestrial topography. Laser ranging is also a tool to study the dynamics of the Moon and fundamental constants. Many of the GNSS satellites now carry retro-reflectors for improved orbit determination, harmonization of reference frames, and in-orbit co-location and system performance validation. The GNSS Constellations will be the means of making the reference frame available to worldwide users. Data and products from these measurements support key aspects of the GEOSS 10-Year implementation Plan adopted on February 16, 2005, The ITRF has been identified as a key contribution of the JAG to GEOSS and the ILRS makes a major contribution for its development since its foundation. The ILRS delivers weekly additional realizations that are accumulated sequentially to extend the ITRF and the Earth Orientation Parameter (EOP) series with a daily resolution. Additional products are currently under development such as precise orbits of satellites, EOP with daily availability, low-degree gravitational harmonics for studies of Earth dynamics and kinematics, etc. SLR technology continues to evolve toward the next generation laser ranging systems as programmatic requirements become more stringent. Ranging accuracy is improving as higher repetition rate, narrower pulse lasers and faster

  19. π-Extended Tetrathiafulvalenes

    DEFF Research Database (Denmark)

    Petersen, Johannes Fabritius

    This Ph.D.-thesis focuses on the synthesis and properties of various redox-active ¼-extended tetrathiafulvalenes. One class of molecules are so-called H-cruciform shaped molecules. In these molecules the formation of a central stilbene double bond is elucidated. Here it was found that the formation...... of the stilbene bond originates from preformation of a 1,3-dioxa-2-phospholane, formed by reaction between P(OEt)3 present under the reaction conditions and two aldehydes. Under the reaction conditions this 1,3-dioxa-2-phospholane can then be converted to the stilbene. These mechanistic studies lead...

  20. Extended spider cognition

    OpenAIRE

    Japyassú, Hilton F.; Laland, Kevin Neville

    2017-01-01

    HFJ received a visiting professor fellowship from Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq - Brazil) (PDE PDE232691/2014-2). Research supported in part by a Grant from the John Templeton Foundation to KNL. There is a tension between the conception of cognition as a central nervous system (CNS) process, and a view of cognition as extending towards the body or the contiguous environment. The centralised conception requires large or complex nervous systems to cope w...

  1. On Range of Skill

    DEFF Research Database (Denmark)

    Hansen, Thomas Dueholm; Miltersen, Peter Bro; Sørensen, Troels Bjerre

    2008-01-01

    is a small number, but only gave heuristic arguments for this. In this paper, we provide the first methods for rigorously estimating the Range of Skill of a given game. We provide some general, asymptotic bounds that imply that the Range of Skill of a perfectly balanced game tree is almost exponential in its......At AAAI'07, Zinkevich, Bowling and Burch introduced the Range of Skill measure of a two-player game and used it as a parameter in the analysis of the running time of an algorithm for finding approximate solutions to such games. They suggested that the Range of Skill of a typical natural game...... size (and doubly exponential in its depth). We also provide techniques that yield concrete bounds for unbalanced game trees and apply these to estimate the Range of Skill of Tic-Tac-Toe and Heads-Up Limit Texas Hold'em Poker. In particular, we show that the Range of Skill of Tic-Tac-Toe is more than...

  2. Point of Technique

    African Journals Online (AJOL)

    .

    Minimally invasive techniques are becoming popular choice for the recent times. These techniques are lowering the cost ... Through a skin incision which extends 2 cm medially from the left anterior-superior iliac Spine ... very invasive surgical procedure , less invasive procedures are becoming the first treatment options and ...

  3. Short-range fundamental forces

    CERN Document Server

    Antoniadis, I; Buchner, M; Fedorov, V V; Hoedl, S; Lambrecht, A; Nesvizhevsky, V V; Pignol, G; Protasov, K V; Reynaud, S; Sobolev, Yu

    2011-01-01

    We consider theoretical motivations to search for extra short-range fundamental forces as well as experiments constraining their parameters. The forces could be of two types: 1) spin-independent forces, 2) spin-dependent axion-like forces. Differe nt experimental techniques are sensitive in respective ranges of characteristic distances. The techniques include measurements of gravity at short distances, searches for extra interactions on top of the Casimir force, precision atomic and neutron experim ents. We focus on neutron constraints, thus the range of characteristic distances considered here corresponds to the range accessible for neutron experiments.

  4. Extended Target Shape Estimation by Fitting B-Spline Curve

    Directory of Open Access Journals (Sweden)

    Jin-long Yang

    2014-01-01

    Full Text Available Taking into account the difficulty of shape estimation for the extended targets, a novel algorithm is proposed by fitting the B-spline curve. For the single extended target tracking, the multiple frame statistic technique is introduced to construct the pseudomeasurement sets and the control points are selected to form the B-spline curve. Then the shapes of the extended targets are extracted under the Bayes framework. Furthermore, the proposed shape estimation algorithm is modified suitably and combined with the probability hypothesis density (PHD filter for multiple extended target tracking. Simulations show that the proposed algorithm has a good performance for shape estimate of any extended targets.

  5. Extending Symfony 2 web application framework

    CERN Document Server

    Armand, Sébastien

    2014-01-01

    Symfony is a high performance PHP framework for developing MVC web applications. Symfony1 allowed for ease of use but its shortcoming was the difficulty of extending it. However, this difficulty has now been eradicated by the more powerful and extensible Symfony2. Information on more advanced techniques for extending Symfony can be difficult to find, so you need one resource that contains the advanced features in a way you can understand. This tutorial offers solutions to all your Symfony extension problems. You will get to grips with all the extension points that Symfony, Twig, and Doctrine o

  6. Remarks on the extended characteristic uncertainty relations

    Energy Technology Data Exchange (ETDEWEB)

    Trifonov, D.A. [Institute for Nuclear Research, Sofia (Bulgaria)

    2001-03-09

    Three remarks concerning the form and the range of validity of the state-extended characteristic uncertainty relations (URs) are presented. A more general definition of the uncertainty matrix for pure and mixed states is suggested. Some new URs are provided. (author). Letter-to-the-editor.

  7. Extending juvenility in grasses

    Energy Technology Data Exchange (ETDEWEB)

    Kaeppler, Shawn; de Leon Gatti, Natalia; Foerster, Jillian

    2017-04-11

    The present invention relates to compositions and methods for modulating the juvenile to adult developmental growth transition in plants, such as grasses (e.g. maize). In particular, the invention provides methods for enhancing agronomic properties in plants by modulating expression of GRMZM2G362718, GRMZM2G096016, or homologs thereof. Modulation of expression of one or more additional genes which affect juvenile to adult developmental growth transition such as Glossy15 or Cg1, in conjunction with such modulation of expression is also contemplated. Nucleic acid constructs for down-regulation of GRMZM2G362718 and/or GRMZM2G096016 are also contemplated, as are transgenic plants and products produced there from, that demonstrate altered, such as extended juvenile growth, and display associated phenotypes such as enhanced yield, improved digestibility, and increased disease resistance. Plants described herein may be used, for example, as improved forage or feed crops or in biofuel production.

  8. Extended Poisson Exponential Distribution

    Directory of Open Access Journals (Sweden)

    Anum Fatima

    2015-09-01

    Full Text Available A new mixture of Modified Exponential (ME and Poisson distribution has been introduced in this paper. Taking the Maximum of Modified Exponential random variable when the sample size follows a zero truncated Poisson distribution we have derived the new distribution, named as Extended Poisson Exponential distribution. This distribution possesses increasing and decreasing failure rates. The Poisson-Exponential, Modified Exponential and Exponential distributions are special cases of this distribution. We have also investigated some mathematical properties of the distribution along with Information entropies and Order statistics of the distribution. The estimation of parameters has been obtained using the Maximum Likelihood Estimation procedure. Finally we have illustrated a real data application of our distribution.

  9. Extending rational maps

    Science.gov (United States)

    Martin, Gaven J.

    We investigate when a rational endomorphism of the Riemann sphere overline{C} extends to a mapping of the upper half-space {H3 which is rational with respect to some measurable conformal structure. Such an extension has the property that it and all its iterates have uniformly bounded distortion. Such maps are called uniformly quasiregular. We show that, in the space of rational mappings of degree d , such an extension is possible in the structurally stable component where there is a single (attracting) component of the Fatou set and the Julia set is a Cantor set. We show that generally outside of this set no such extension is possible. In particular, polynomials can never admit such an extension.

  10. Reduced Extended MHD

    Science.gov (United States)

    Morrison, P. J.; Abdelhamid, H. M.; Grasso, D.; Hazeltine, R. D.; Lingam, M.; Tassi, E.

    2015-11-01

    Over the years various reduced fluid models have been obtained for modeling plasmas, with the goal of capturing important physics while maintaining computability. Such models have included the physics contained in various generalizations of Ohm's law, including Hall drift and electron inertia. In a recent publication it was shown that full 3D extended MHD is a Hamiltonian system by finding its noncanonical Poisson bracket. Subsequently, this bracket was shown to be derivable from that for Hall MHD by a series of remarkable transformations, which greatly simplifies the proof of the Jacobi identity and allows one to immediately obtain generalizations of the helicity and cross helicity. In this poster we use this structure to obtain exact reduced fluid models with the effects of full two-fluid theory. Results of numerical computations of collisionless reconnection using an exact reduced 4-field model will be presented and analytical comparisons of mode structure of previous reduced models will be made.

  11. Caractérisation de quelques stabilisants naturels de l'émulsion d'eau dans le pétrole brut, grace à l'extension de la technique de "moussage" au système liquide-liquide eau-huile Characterising Several Natural Stabilizants of Water Emulsion in Crude Oil by Extending the "Foaming" Technique to Oil/Water Liquid-Liquid Systems

    Directory of Open Access Journals (Sweden)

    Coste J. -F.

    2006-11-01

    Full Text Available L'extension de la technique, de " moussage "au système liquide-liquide eau-pétrole brut a permis d'augmenter la concentration d'une fraction du pétrole en acides naphténiques, amines, asphaltènes et porphyrines, grâce à l'accroissement de l'aire de l'interface entre les deux phases non miscibles. Ces espèces chimiques présentes à l'interface favorisent la formation des films entre les gouttelettes de phase aqueuse dispersée. Elles sont à l'origine de la stabilité de I'émulsion d'eau dans le pétrole. The " foaming " technique was extended to a water/crude-oil liquid-liquid system so as to increase the concentration of naphthenic acids, amines, asphaltenes and porphyrins in an oil fraction by enlarging the interface orea between the two immiscible phases. The presence of these chemical species at the interface promotes the formation of films between the dispersed aqueuss-phase droplets. They are at the origin of the stability of a water in oil emulsion.

  12. Online Sorted Range Reporting

    DEFF Research Database (Denmark)

    Brodal, Gerth Stølting; Fagerberg, Rolf; Greve, Mark

    2009-01-01

    We study the following one-dimensional range reporting problem: On an arrayA of n elements, support queries that given two indices i ≤ j and an integerk report the k smallest elements in the subarray A[i..j] in sorted order. We present a data structure in the RAM model supporting such queries...... in optimal O(k) time. The structure uses O(n) words of space and can be constructed in O(n logn) time. The data structure can be extended to solve the online version of the problem, where the elements in A[i..j] are reported one-by-one in sorted order, in O(1) worst-case time per element. The problem...... is motivated by (and is a generalization of) a problem with applications in search engines: On a tree where leaves have associated rank values, report the highest ranked leaves in a given subtree. Finally, the problem studied generalizes the classic range minimum query (RMQ) problem on arrays....

  13. Extended Mixed Vector Equilibrium Problems

    Directory of Open Access Journals (Sweden)

    Mijanur Rahaman

    2014-01-01

    Full Text Available We study extended mixed vector equilibrium problems, namely, extended weak mixed vector equilibrium problem and extended strong mixed vector equilibrium problem in Hausdorff topological vector spaces. Using generalized KKM-Fan theorem (Ben-El-Mechaiekh et al.; 2005, some existence results for both problems are proved in noncompact domain.

  14. THE EXTENDED VIRGO CLUSTER CATALOG

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Suk; Rey, Soo-Chang; Lee, Youngdae; Chung, Jiwon; Pak, Mina; Yi, Wonhyeong; Lee, Woong [Department of Astronomy and Space Science, Chungnam National University, 99 Daehak-ro, Daejeon 305-764 (Korea, Republic of); Jerjen, Helmut [Research School of Astronomy and Astrophysics, The Australian National University, Cotter Road, Weston, ACT 2611 (Australia); Lisker, Thorsten [Astronomisches Rechen-Institut, Zentrum für Astronomie der Universität Heidelberg (ZAH), Mönchhofstraße 12-14, D-69120 Heidelberg (Germany); Sung, Eon-Chang [Korea Astronomy and Space Science institute, 776 Daedeokdae-ro, Daejeon 305-348 (Korea, Republic of)

    2015-01-01

    We present a new catalog of galaxies in the wider region of the Virgo cluster, based on the Sloan Digital Sky Survey (SDSS) Data Release 7. The Extended Virgo Cluster Catalog (EVCC) covers an area of 725 deg{sup 2} or 60.1 Mpc{sup 2}. It is 5.2 times larger than the footprint of the classical Virgo Cluster Catalog (VCC) and reaches out to 3.5 times the virial radius of the Virgo cluster. We selected 1324 spectroscopically targeted galaxies with radial velocities less than 3000 km s{sup –1}. In addition, 265 galaxies that have been overlooked in the SDSS spectroscopic survey but have available redshifts in the NASA Extragalactic Database are also included. Our selection process secured a total of 1589 galaxies, 676 of which are not included in the VCC. The certain and possible cluster members are defined by means of redshift comparison with a cluster infall model. We employed two independent and complementary galaxy classification schemes: the traditional morphological classification based on the visual inspection of optical images and a characterization of galaxies from their spectroscopic features. SDSS u, g, r, i, and z passband photometry of all EVCC galaxies was performed using Source Extractor. We compare the EVCC galaxies with the VCC in terms of morphology, spatial distribution, and luminosity function. The EVCC defines a comprehensive galaxy sample covering a wider range in galaxy density that is significantly different from the inner region of the Virgo cluster. It will be the foundation for forthcoming galaxy evolution studies in the extended Virgo cluster region, complementing ongoing and planned Virgo cluster surveys at various wavelengths.

  15. Topics in Extended Dynamical Systems

    Science.gov (United States)

    Bhagavatula, Ravi S.

    This thesis consists of three chapters. Each chapter is self-contained and is devoted to the investigation of a particular topic in extended dynamical systems. In the first chapter, an approach based on Langevin equations is implemented to understand the non-Gaussian nature of the probability distribution function (PDF) of local diffusive variables in extended dynamical systems, e.g., a passive scalar advected by turbulent velocity fluctuations. Two mechanisms are proposed for the origin of non-Gaussian tails: One relies on the nature of temporal correlations of the fluctuations that couple additively to the diffusive field, leading to exponential and stretched exponential tails in the PDF; the other depends on multiplicative coupling between the diffusive field and the fluctuations, producing algebraic tails in the PDF. The mechanisms are illustrated using models for a passive scalar and also a current driven Josephson junction array. This study indicates that shapes of local PDFs in turbulent states are non-universal and crucially depend on local couplings and time scales. The second chapter establishes the existence of a class of locally conserving chaotic (deterministic) systems that exhibit Generic Scale Invariance--algebraic decay of spatial and temporal correlations without tuning parameters. This study also reveals the similarity between noise and chaos in extended systems as far as long-wavelength and long -time behavior is concerned. Specifically, a two dimensional coupled-map lattice model with a conserved density is numerically shown to exhibit, in agreement with heuristic arguments, algebraic decay of spatio-temporal correlations in chaotic states with simple predictable exponents. The third chapter investigates scaling behavior of earthquakes in seismic zone models in which an earthquake is modeled by a quasi-static description that ignores short -time dynamics during an earthquake. The models incorporate the essential feature of long-ranged stress

  16. Extending the Modelling Framework for Gas-Particle Systems

    DEFF Research Database (Denmark)

    Rosendahl, Lasse Aistrup

    An extended Lagrangian particle tracking and combustion model for non-conventional solid fuels such as chopped straw has been developed. Based on an extension of the existing tracking techniques, shapes are based on a superelliptic equation capable of assuming forms ranging from spheres...... to cylinders, through simple parameter variation. Using a concept of aerodynamical similarity, a drag coefficient accounting for orientability as well as shape variations has been defined. The model has been applied to two isothermal testcases, where different types of particles are injected into swirling flow...... configurations. In both cases, the model performs efficiently, and indicates a pronounced difference in terms of the aerodynamic properties of the different particle shapes. For validation purposes, terminal velocity predictions of different shapes have been carried out, and compared to experimental data...

  17. [Extended endoscopic endonasal approach to skull base].

    Science.gov (United States)

    López-Arbolay, Omar; González-González, Justo; Rojas-Manresa, Jorge Luis

    2012-11-01

    Different approaches to the skull base have been developed through the sphenoidal sinus. Traditional boundaries of the trans-sphenoidal approach can be extended in antero-posterior and lateral plane. We review our experience with extended endoscopic endonasal approach in 127 cases. We used the extended endoscopic endonasal approach in 127 patients with different lesions of the skull base. This study specifically focuses on: type of lesions, surgical approach, outcome and surgical complications. Extended endoscopic endonasal approach was used in 127 patients with following lesions: 61 invasive adenomas to cavernous sinus, 10 clival chordomas, 21 craniopharyngiomas, 26 meningiomas, 4 cerebrospinal fluid leakages, one meningoencephalocele, 2 malignan lesions and 2 thyroid ophthalmopathy. In tumoral lesions gross total resection was achieved in 82.5%, with better results in craniopharyngiomas 90.5%, followed by invasive adenomas with 85.2%, and meningiomas with 84.6%. The most frequent complications were the insipid (8.6%) diabetes, meningoencefalitis (3.9%) and the hydrocephalic (3.9%). Mortality was 3.9%. The extended endoscopic endonasal approach is a promising minimally invasive alternative for selective cases with skull base lesions. As techniques and technology advance this approach may become the procedure of choice for most lesions and should be considered an option in the management of the patients with these complex pathologies by skull base surgeon. Copyright © 2012 Sociedad Española de Neurocirugía. Published by Elsevier España. All rights reserved.

  18. Extended linear chain compounds

    CERN Document Server

    Linear chain substances span a large cross section of contemporary chemistry ranging from covalent polymers, to organic charge transfer com­ plexes to nonstoichiometric transition metal coordination complexes. Their commonality, which coalesced intense interest in the theoretical and exper­ imental solid state physics/chemistry communities, was based on the obser­ vation that these inorganic and organic polymeric substrates exhibit striking metal-like electrical and optical properties. Exploitation and extension of these systems has led to the systematic study of both the chemistry and physics of highly and poorly conducting linear chain substances. To gain a salient understanding of these complex materials rich in anomalous aniso­ tropic electrical, optical, magnetic, and mechanical properties, the conver­ gence of diverse skills and talents was required. The constructive blending of traditionally segregated disciplines such as synthetic and physical organic, inorganic, and polymer chemistry, crystallog...

  19. Combinatorial techniques

    CERN Document Server

    Sane, Sharad S

    2013-01-01

    This is a basic text on combinatorics that deals with all the three aspects of the discipline: tricks, techniques and theory, and attempts to blend them. The book has several distinctive features. Probability and random variables with their interconnections to permutations are discussed. The theme of parity has been specially included and it covers applications ranging from solving the Nim game to the quadratic reciprocity law. Chapters related to geometry include triangulations and Sperner's theorem, classification of regular polytopes, tilings and an introduction to the Eulcidean Ramsey theory. Material on group actions covers Sylow theory, automorphism groups and a classification of finite subgroups of orthogonal groups. All chapters have a large number of exercises with varying degrees of difficulty, ranging from material suitable for Mathematical Olympiads to research.

  20. [THE EFFECT OF THE APPLICATION OF THE KINESIOLOGY TAPING TECHNIQUE FOR MUSCLE RANGE OF MOTION OF THE LUMBAR SPINE, AND THE SUBJECTIVE PERCEPTION OF PAIN INTENSITY IN PATIENTS WITH BACK PAIN].

    Science.gov (United States)

    Garczyński, Wojciech; Lubkowska, Anna; Dobek, Aleksandra; Andryszczyk, Marek

    2014-01-01

    In an era of ubiquitous computing, a considerable part of the population, regardless of age group, spend more time in a sitting position. Long-term, static loading of the spine increases muscle tension, leading to the occurrence of pain. Physiotherapy is recommended as primary and secondary prevention of spinal pain symptoms. The Kinesiology Taping Method is one of the many special methods of physiotherapy which is used during the episodes of back pain in the lumbosacral region. This method consists in sticking on a special tape, which is made of stretch cotton similar to human skin, using a variety of techniques for patch application. The present study evaluated the effect of the application of the Kinesiology Taping technique for muscle mobility in the lumbar spine and the subjective perception of pain intensity. The study group consisted of 100 patients (89 women and 11 men) who experienced pain in the lumbar spine. To assess the mobility of the lumbar spine the Schober test was used. The subjective sensation of pain was assessed using the VAS (visual analogue scale). Measurements were taken four times: before gluing applications, immediately after taping, 7 days after application of the patch, and immediately after its removal. In response to the use of therapy, an increase of mobility of the lumbar spine in flexion front and back, and reduced pain was shown. Application of the muscle kinesiology taping technique is an effective method in reducing pain and increasing mobility of the lumbar spine.

  1. Method for Improving Indoor Positioning Accuracy Using Extended Kalman Filter

    Directory of Open Access Journals (Sweden)

    Seoung-Hyeon Lee

    2016-01-01

    Full Text Available Beacons using bluetooth low-energy (BLE technology have emerged as a new paradigm of indoor positioning service (IPS because of their advantages such as low power consumption, miniaturization, wide signal range, and low cost. However, the beacon performance is poor in terms of the indoor positioning accuracy because of noise, motion, and fading, all of which are characteristics of a bluetooth signal and depend on the installation location. Therefore, it is necessary to improve the accuracy of beacon-based indoor positioning technology by fusing it with existing indoor positioning technology, which uses Wi-Fi, ZigBee, and so forth. This study proposes a beacon-based indoor positioning method using an extended Kalman filter that recursively processes input data including noise. After defining the movement of a smartphone on a flat two-dimensional surface, it was assumed that the beacon signal is nonlinear. Then, the standard deviation and properties of the beacon signal were analyzed. According to the analysis results, an extended Kalman filter was designed and the accuracy of the smartphone’s indoor position was analyzed through simulations and tests. The proposed technique achieved good indoor positioning accuracy, with errors of 0.26 m and 0.28 m from the average x- and y-coordinates, respectively, based solely on the beacon signal.

  2. Current developments in composite materials and techniques.

    Science.gov (United States)

    Dietschi, D; Dietschi, J M

    1996-09-01

    General reduction of dental caries and patient interest in dental aesthetics have resulted in the development of new restorative materials and techniques. Composite materials and adhesive techniques have become the foundation of modern restorative dentistry. Mechanical performance, wear resistance, and aesthetic potential of composite resins have been significantly improved, and the material is now used in cases ranging from the restoration of initial decays and cosmetic corrections to the veneering in extended prosthetic rehabilitation. Polymerization shrinkage of the resin matrix remains a challenge and still imposes limitations in the application of direct techniques. The learning objective of this article is to review the most significant advances of composite materials and the importance of utilizing the available treatment options with discretion, selecting those which preserve the tooth structure and require the least maintenance.

  3. Close range photogrammetry and machine vision

    CERN Document Server

    Atkinson, KB

    1996-01-01

    This book presents the methodology, algorithms, techniques and equipment necessary to achieve real time digital photogrammetric solutions, together with contemporary examples of close range photogrammetry.

  4. Extending cosmology: the metric approach

    OpenAIRE

    Mendoza, S.

    2012-01-01

    Comment: 2012, Extending Cosmology: The Metric Approach, Open Questions in Cosmology; Review article for an Intech "Open questions in cosmology" book chapter (19 pages, 3 figures). Available from: http://www.intechopen.com/books/open-questions-in-cosmology/extending-cosmology-the-metric-approach

  5. On core stability and extendability

    OpenAIRE

    Shellshear, Evan

    2011-01-01

    This paper investigates conditions under which the core of a TU cooperative game is stable. In particular the author extends the idea of extendability to find new conditions under which the core is stable. It is also shown that these new conditions are not necessary for core stability.

  6. Analysis of printed reflectarrays using extended local periodicity

    DEFF Research Database (Denmark)

    Zhou, Min; Sorensen, Stig Busk; Jorgensen, Erik

    2011-01-01

    An analysis technique for improved modeling of a printed reflectarray is proposed. The technique is based on a periodic approach where periodicity is applied on an extended unit cell, which includes the actual elements surrounding the element under consideration. An offset reflectarray sample has...

  7. Outcomes of extended transforaminal lumbar interbody fusion for lumbar spondylosis.

    Science.gov (United States)

    Talia, Adrian J; Wong, Michael L; Lau, Hui C; Kaye, Andrew H

    2015-11-01

    This study aims to assess the results of extended transforaminal lumbar interbody fusion (TLIF) for a two surgeon, single institution series. In total, extended TLIF with bilateral decompression was performed in 57 patients. Pain, American Spinal Injury Association scores, patient demographics, body mass index (BMI), perioperative indices and radiographic measurements were recorded and analysed. The surgeries were performed between February 2011 and January 2014 on 38 women and 19 men. The mean patient age was 62.86 years, and the mean BMI was 30.31 kg/m(2). In 49 patients, spondylolisthesis was the primary indication. The mean intraoperative time was 284.65 min, and this decreased as the series progressed. The median length of stay was 5 days (range: 2-9). The surgical complication rate was 19.3%. Two patients died from cardiopulmonary complications. Single level TLIF was performed in 78.9% of the cohort, with L4/5 the most commonly fused level. Significant pain reduction was achieved from a mean (± standard deviation) preoperative visual analogue scale (VAS) of 8.28 ± 1.39 to 1.50 ± 1.05 at 12 months postoperatively. No patients deteriorated neurologically. Spondylolisthesis was significantly corrected from a preoperative mean of 6.82 mm to 2.80 mm postoperatively. Although there is a learning curve associated with the procedure, extended TLIF with bilateral facet joint removal and decompression appeared to be a safe and effective alternative to other fusion techniques, and our results were comparable to other published case series. The stabilisation and correction of spinal deformity reduces pain, aids neurologic recovery and improves quality of life. Copyright © 2015 Elsevier Ltd. All rights reserved.

  8. Extended Active Disturbance Rejection Controller

    Science.gov (United States)

    Gao, Zhiqiang (Inventor); Tian, Gang (Inventor)

    2016-01-01

    Multiple designs, systems, methods and processes for controlling a system or plant using an extended active disturbance rejection control (ADRC) based controller are presented. The extended ADRC controller accepts sensor information from the plant. The sensor information is used in conjunction with an extended state observer in combination with a predictor that estimates and predicts the current state of the plant and a co-joined estimate of the system disturbances and system dynamics. The extended state observer estimates and predictions are used in conjunction with a control law that generates an input to the system based in part on the extended state observer estimates and predictions as well as a desired trajectory for the plant to follow.

  9. Atomic Structure and Properties of Extended Defects in Silicon

    Energy Technology Data Exchange (ETDEWEB)

    Buczko, R.; Chisholm, M.F.; Kaplan, T.; Maiti, A.; Mostoller, M.; Pantelides, S.T.; Pennycook, S.J.

    1998-10-15

    The Z-contrast technique represents a new approach to high-resolution electron microscopy allowing for the first time incoherent imaging of materials on the atomic scale. The key advantages of the technique, an intrinsically higher resolution limit and directly interpretable, compositionally sensitive imaging, allow a new level of insight into the atomic configurations of extended defects in silicon. This experimental technique has been combined with theoretical calculations (a combination of first principles, tight binding, and classical methods) to extend this level of insight by obtaining the energetic and electronic structure of the defects.

  10. Range Compressed Holographic Aperture Ladar

    Science.gov (United States)

    2017-06-01

    step 1. This image can be obtained through any digital holography processing technique and contains no range information. Since the penny has a... digital holography, laser, active imaging , remote sensing, laser imaging 16. SECURITY CLASSIFICATION OF: 17. LIMITATION OF ABSTRACT: SAR 8...30 15. Digital Hologram Image

  11. Simultaneous measurement of spectra at multiple ranges using a single spectrometer.

    Science.gov (United States)

    Lienert, Barry; Porter, John; Sharma, Shiv K

    2009-08-20

    We have designed and built an instrument having the capability to measure and display spectra at multiple ranges near simultaneously in real time. An excitation laser beam is oriented parallel to and offset from the axis of the light collection optics. The image of the laser beam is then displaced with range. Multiple optical fibers collect the displaced images at different ranges. The output ends of these fibers are positioned vertically along the input slit of a spectrometer that disperses the light from each fiber along different rows of the spectrometer's two-dimensional detector array. The detector array rows then give an immediate visual comparison of spectra at different ranges. A small prototype of this system covering a range from 3 to 13 m has been built. It has been successfully tested using containers holding two distinct fluorescent dyes. Numerical simulations indicate that the technique can be extended to longer-range systems.

  12. Steady-State Equilibrium Phase Inversion Recovery ON-resonant Water Suppression (IRON) Magnetic Resonance Angiography in Conjunction with Superparamagnetic Nanoparticles. A Robust Technique for Imaging within a Wide Range of Contrast Agent Dosages

    Science.gov (United States)

    Gitsioudis, Gitsios; Stuber, Matthias; Arend, Ingolf; Thomas, Moritz; Yu, Jing; Hilbel, Thomas; Giannitsis, Evangelos; Katus, Hugo A.; Korosoglou, Grigorios

    2012-01-01

    Objectives To investigate the ability of inversion recovery ON-resonant water suppression (IRON) in conjunction with P904 (superparamagnetic nanoparticles which consisting of a maghemite core coated with a low-molecular-weight amino-alcohol derivative of glucose) to perform steady-state equilibrium phase magnetic resonance angiography (MRA) over a wide dose range. Materials and Methods Experiments were approved by the institutional animal care committee. Rabbits (n=12) were imaged at baseline and serially after the administration of 10 incremental dosages of 0.57–5.7 mgFe/Kg P904. Conventional T1-weighted and IRON MRA were obtained on a clinical 1.5-T scanner to image the thoracic and abdominal aorta, and peripheral vessels. Contrast-to-noise ratios (CNR) and vessel sharpness were quantified. Results Using IRON MRA, CNR and vessel sharpness progressively increased with incremental dosages of the contrast agent P904, exhibiting constantly higher contrast values than T1-weighted MRA over a very wide range of contrast agent doses (CNR of 18.8±5.6 for IRON versus 11.1±2.8 for T1-weighted MRA at 1.71 mgFe/kg, p=0.02 and 19.8±5.9 for IRON versus −0.8±1.4 for T1-weighted MRA at 3.99 mgFe/kg, p=0.0002). Similar results were obtained for vessel sharpness in peripheral vessels, (Vessel sharpness of 46.76±6.48% for IRON versus 33.20±3.53% for T1-weighted MRA at 1.71 mgFe/Kg, p=0.002, and of 48.66±5.50% for IRON versus 19.00±7.41% for T1-weighted MRA at 3.99 mgFe/Kg, p=0.003). Conclusion Our study suggests that quantitative CNR and vessel sharpness after the injection of P904 are consistently higher for IRON MRA when compared to conventional T1-weighted MRA. These findings apply for a wide range of contrast agent dosages. PMID:23418107

  13. On Extending Neural Networks with Loss Ensembles for Text Classification

    OpenAIRE

    Hajiabadi, Hamideh; Molla-Aliod, Diego; Monsefi, Reza

    2017-01-01

    Ensemble techniques are powerful approaches that combine several weak learners to build a stronger one. As a meta learning framework, ensemble techniques can easily be applied to many machine learning techniques. In this paper we propose a neural network extended with an ensemble loss function for text classification. The weight of each weak loss function is tuned within the training phase through the gradient propagation optimization method of the neural network. The approach is evaluated on...

  14. Extended Self Similarity in Solar Wind Turbulence

    Science.gov (United States)

    Rowlands, G.; Chapman, S. C.; Hnat, B.

    2005-12-01

    The solar wind provides a natural laboratory for observations of MHD turbulence over extended temporal scales. A hallmark of turbulence is scaling- and scaling in the Probability Density Functions (PDF) of fluctuations in certain solar wind in- situ bulk plasma parameters has been established from WIND and ACE observations on `short' timescales up to a few hours. On longer timescales there is a crossover in scaling to uncorrelated behaviour. The intermittency of the system is expressed in these parameters through the non-Gaussian nature of the fluctuations PDF up to this timescale. Here we apply a generic approach to turbulence- that of Extended Self Similarity (ESS)- to the analysis of solar wind observations. We find that ESS can extend the range of scaling and for some parameters reveals two distinct scaling regions for the `short' and long timescales, whereas for others, a single scaling encompasses the behaviour over the full range of timescales. That certain parameters, and conditions, can be distinguished via ESS may provide physical insight into the turbulent solar wind.

  15. Experimental techniques; Techniques experimentales

    Energy Technology Data Exchange (ETDEWEB)

    Roussel-Chomaz, P. [GANIL CNRS/IN2P3, CEA/DSM, 14 - Caen (France)

    2007-07-01

    This lecture presents the experimental techniques, developed in the last 10 or 15 years, in order to perform a new class of experiments with exotic nuclei, where the reactions induced by these nuclei allow to get information on their structure. A brief review of the secondary beams production methods will be given, with some examples of facilities in operation or under project. The important developments performed recently on cryogenic targets will be presented. The different detection systems will be reviewed, both the beam detectors before the targets, and the many kind of detectors necessary to detect all outgoing particles after the reaction: magnetic spectrometer for the heavy fragment, detection systems for the target recoil nucleus, {gamma} detectors. Finally, several typical examples of experiments will be detailed, in order to illustrate the use of each detector either alone, or in coincidence with others. (author)

  16. An extended Farm Site Development Method

    Directory of Open Access Journals (Sweden)

    Eugene Hanekom

    2016-09-01

    Full Text Available The inefficient and ineffective use of arable land in South Africa is one of the numerous challenges within its agricultural sector. Previous research has indicated that a method, the Farm Site Development Method (FSDM, could increase the effective and efficient use of arable land by providing a roadmap to the farm owner for incrementally transforming the current state facilities and resources of a farm towards a future saturation state. The FSDM was then demonstrated at a crop-producing farm and several opportunities existed to extend its utility. Here we suggest its extension for application to a livestock farm, and also include optimisation techniques, demand planning and financial planning.

  17. Topological defects in extended inflation

    Energy Technology Data Exchange (ETDEWEB)

    Copeland, E.J. (Department of Physics, University of Sussex, Brighton BN1 9QH (United Kingdom)); Kolb, E.W. (NASA/Fermilab Astrophysics Center, Fermi National Accelerator Laboratory, Batavia, IL (USA) Department of Astronomy and Astrophysics, Enrico Fermi Institute, The University of Chicago, Chicago, IL (USA)); Liddle, A.R. (Astronomy Centre, Department of Physics, University of Sussex, Brighton (United Kingdom))

    1990-10-15

    We consider the production of topological defects, especially cosmic strings, in extended-inflation models. In extended inflation, the Universe passes through a first-order phase transition via bubble percolation, which naturally allows defects to form at the end of inflation. The correlation length, which determines the number density of the defects, is related to the mean size of the bubbles when they collide. This mechanism allows a natural combination of inflation and large-scale structure via cosmic strings.

  18. Topological defects in extended inflation

    Energy Technology Data Exchange (ETDEWEB)

    Copeland, E.J. (Sussex Univ., Brighton (UK). Dept. of Physics); Kolb, E.W. (Fermi National Accelerator Lab., Batavia, IL (USA) Chicago Univ., IL (USA). Enrico Fermi Inst.); Liddle, A.R. (Sussex Univ., Brighton (UK). Astronomy Centre)

    1990-04-01

    We consider the production of topological defects, especially cosmic strings, in extended inflation models. In extended inflation, the Universe passes through a first-order phase transition via bubble percolation, which naturally allows defects to form at the end of inflation. The correlation length, which determines the number density of the defects, is related to the mean size of bubbles when they collide. This mechanism allows a natural combination of inflation and large-scale structure via cosmic strings. 18 refs.

  19. Extended lactation in dairy cows

    DEFF Research Database (Denmark)

    Sorensen, Annette; Muir, D. Donald; Knight, Christopher Harold

    2008-01-01

    of the lactation, protein and fat percentages increasing and lactose percentage decreasing, irrespective of treatment. The quality of the milk for processing into cheese, fermented products, heat-treated products and cream liqueurs was assessed by calculation of casein number (casein protein as a proportion...... interventions, the results lend support to the economic arguments in favour of extended lactation cycles. The likely welfare benefits of extended lactation are also discussed....

  20. Extender for securing a closure

    Science.gov (United States)

    Thomas, II, Patrick A.

    2012-10-02

    An apparatus for securing a closure such as door or a window that opens and closes by movement relative to a fixed structure such as a wall or a floor. Many embodiments provide a device for relocating a padlock from its normal location where it secures a fastener (such as a hasp) to a location for the padlock that is more accessible for locking and unlocking the padlock. Typically an extender is provided, where the extender has a hook at a first end that is disposed through the eye of the staple of the hasp, and at an opposing second end the extender has an annulus, such as a hole in the extender or a loop or ring affixed to the extender. The shackle of the padlock may be disposed through the annulus and may be disposed through the eye of a second staple to secure the door or window in a closed or open position. Some embodiments employ a rigid sheath to enclose at least a portion of the extender. Typically the rigid sheath has an open state where the hook is exposed outside the sheath and a closed state where the hook is disposed within the sheath.

  1. Extending product modeling methods for integrated product development

    DEFF Research Database (Denmark)

    Bonev, Martin; Wörösch, Michael; Hauksdóttir, Dagný

    2013-01-01

    . Updated design requirements have then to be made explicit and mapped against the existing product architecture. In this paper, existing methods are adapted and extended through linking updated requirements to suitable product models. By combining several established modeling techniques, such as the DSM......Despite great efforts within the modeling domain, the majority of methods often address the uncommon design situation of an original product development. However, studies illustrate that development tasks are predominantly related to redesigning, improving, and extending already existing products...

  2. Solvability of Extended General Strongly Mixed Variational Inequalities

    Directory of Open Access Journals (Sweden)

    Balwant Singh Thakur

    2013-10-01

    Full Text Available In this paper, a new class of extended general strongly mixed variational inequalities is introduced and studied in Hilbert spaces. An existence theorem of solution is established and using resolvent operator technique, a new iterative algorithm for solving the extended general strongly mixed variational inequality is suggested. A convergence result for the iterative sequence generated by the new algorithm is also established.

  3. Affinity Propagation Clustering of Measurements for Multiple Extended Target Tracking

    Directory of Open Access Journals (Sweden)

    Tao Zhang

    2015-09-01

    Full Text Available More measurements are generated by the target per observation interval, when the target is detected by a high resolution sensor, or there are more measurement sources on the target surface. Such a target is referred to as an extended target. The probability hypothesis density filter is considered an efficient method for tracking multiple extended targets. However, the crucial problem of how to accurately and effectively partition the measurements of multiple extended targets remains unsolved. In this paper, affinity propagation clustering is introduced into measurement partitioning for extended target tracking, and the elliptical gating technique is used to remove the clutter measurements, which makes the affinity propagation clustering capable of partitioning the measurement in a densely cluttered environment with high accuracy. The Gaussian mixture probability hypothesis density filter is implemented for multiple extended target tracking. Numerical results are presented to demonstrate the performance of the proposed algorithm, which provides improved performance, while obviously reducing the computational complexity.

  4. Affinity Propagation Clustering of Measurements for Multiple Extended Target Tracking.

    Science.gov (United States)

    Zhang, Tao; Wu, Renbiao

    2015-09-08

    More measurements are generated by the target per observation interval, when the target is detected by a high resolution sensor, or there are more measurement sources on the target surface. Such a target is referred to as an extended target. The probability hypothesis density filter is considered an efficient method for tracking multiple extended targets. However, the crucial problem of how to accurately and effectively partition the measurements of multiple extended targets remains unsolved. In this paper, affinity propagation clustering is introduced into measurement partitioning for extended target tracking, and the elliptical gating technique is used to remove the clutter measurements, which makes the affinity propagation clustering capable of partitioning the measurement in a densely cluttered environment with high accuracy. The Gaussian mixture probability hypothesis density filter is implemented for multiple extended target tracking. Numerical results are presented to demonstrate the performance of the proposed algorithm, which provides improved performance, while obviously reducing the computational complexity.

  5. A GPU-accelerated extended Kalman filter

    Science.gov (United States)

    Wei, Shih-Chieh; Huang, Bormin

    2011-11-01

    The extended Kalman filter is one of the most widely used techniques for state estimation of nonlinear systems. In its two steps of forecast and data assimilation, many matrix operations including multiplication and inversion are involved. As recent graphic processor units (GPU) have shown to provide much speedup in matrix operations, we will explore in this work a GPU-based implementation of the extended Kalman filter. The Compute Unified Device Architecture (CUDA) on the Nvidia GeForce GTX 590 GPU hardware will be used for comparison with a single threaded CPU counterpart. Experiments were conducted on typical large-scale over-determined systems with thousands of components in states and measurements. Within the GPU memory limit, a speedup of 1386x is achieved for a system with measurements having 5000 components and states having 3750 components. The speedup profile for various combinations of measurement and state sizes will serve as good reference for future implementation of extended Kalman filter on real large-scale applications.

  6. Extended pie menus for immersive virtual environments.

    Science.gov (United States)

    Gebhardt, Sascha; Pick, Sebastian; Leithold, Franziska; Hentschel, Bernd; Kuhlen, Torsten

    2013-04-01

    Pie menus are a well-known technique for interacting with 2D environments and so far a large body of research documents their usage and optimizations. Yet, comparatively little research has been done on the usability of pie menus in immersive virtual environments (IVEs). In this paper we reduce this gap by presenting an implementation and evaluation of an extended hierarchical pie menu system for IVEs that can be operated with a six-degrees-of-freedom input device. Following an iterative development process, we first developed and evaluated a basic hierarchical pie menu system. To better understand how pie menus should be operated in IVEs, we tested this system in a pilot user study with 24 participants and focus on item selection. Regarding the results of the study, the system was tweaked and elements like check boxes, sliders, and color map editors were added to provide extended functionality. An expert review with five experts was performed with the extended pie menus being integrated into an existing VR application to identify potential design issues. Overall results indicated high performance and efficient design.

  7. A quantum inspired model of radar range and range-rate measurements with applications to weak value measurements

    Science.gov (United States)

    Escalante, George

    2017-05-01

    Weak Value Measurements (WVMs) with pre- and post-selected quantum mechanical ensembles were proposed by Aharonov, Albert, and Vaidman in 1988 and have found numerous applications in both theoretical and applied physics. In the field of precision metrology, WVM techniques have been demonstrated and proven valuable as a means to shift, amplify, and detect signals and to make precise measurements of small effects in both quantum and classical systems, including: particle spin, the Spin-Hall effect of light, optical beam deflections, frequency shifts, field gradients, and many others. In principal, WVM amplification techniques are also possible in radar and could be a valuable tool for precision measurements. However, relatively limited research has been done in this area. This article presents a quantum-inspired model of radar range and range-rate measurements of arbitrary strength, including standard and pre- and post-selected measurements. The model is used to extend WVM amplification theory to radar, with the receive filter performing the post-selection role. It is shown that the description of range and range-rate measurements based on the quantum-mechanical measurement model and formalism produces the same results as the conventional approach used in radar based on signal processing and filtering of the reflected signal at the radar receiver. Numerical simulation results using simple point scatterrer configurations are presented, applying the quantum-inspired model of radar range and range-rate measurements that occur in the weak measurement regime. Potential applications and benefits of the quantum inspired approach to radar measurements are presented, including improved range and Doppler measurement resolution.

  8. Airway Clearance Techniques (ACTs)

    Medline Plus

    Full Text Available ... a Family Parenting as an Adult With CF Treatments & Therapies People with cystic fibrosis are living longer ... to specialized CF care and a range of treatment options. Airway Clearance Active Cycle of Breathing Technique ...

  9. Airway Clearance Techniques (ACTs)

    Medline Plus

    Full Text Available ... a Family Parenting as an Adult With CF Treatments & Therapies People with cystic fibrosis are living longer and ... to specialized CF care and a range of treatment options. Airway Clearance Active Cycle of Breathing Technique ( ...

  10. Viability of bull semen extended with commercial semen extender ...

    African Journals Online (AJOL)

    Andrea Raseona

    Abstract. The aim of this study was to evaluate the viability of bull spermatozoa diluted with commercial semen extender and two culture media stored at controlled room temperature (24 °C) for 72 hours. Two Nguni bulls were used for semen collection with the aid of an electro-ejaculator. After macroscopic evaluation ...

  11. Extended cognition in science communication.

    Science.gov (United States)

    Ludwig, David

    2014-11-01

    The aim of this article is to propose a methodological externalism that takes knowledge about science to be partly constituted by the environment. My starting point is the debate about extended cognition in contemporary philosophy and cognitive science. Externalists claim that human cognition extends beyond the brain and can be partly constituted by external devices. First, I show that most studies of public knowledge about science are based on an internalist framework that excludes the environment we usually utilize to make sense of science and does not allow the possibility of extended knowledge. In a second step, I argue that science communication studies should adopt a methodological externalism and accept that knowledge about science can be partly realized by external information resources such as Wikipedia. © The Author(s) 2013.

  12. Range management visual impacts

    Science.gov (United States)

    Bruce R. Brown; David Kissel

    1979-01-01

    Historical overgrazing of western public rangelands has resulted in the passage of the Public Rangeland Improvement Act of 1978. The main purpose of this Act is to improve unsatisfactory range conditions. A contributing factor to unfavorable range conditions is adverse visual impacts. These visual impacts can be identified in three categories of range management: range...

  13. Automatic localization of cochlear implant electrodes in CTs with a limited intensity range

    Science.gov (United States)

    Zhao, Yiyuan; Dawant, Benoit M.; Noble, Jack H.

    2017-02-01

    Cochlear implants (CIs) are neural prosthetics for treating severe-to-profound hearing loss. Our group has developed an image-guided cochlear implant programming (IGCIP) system that uses image analysis techniques to recommend patientspecific CI processor settings to improve hearing outcomes. One crucial step in IGCIP is the localization of CI electrodes in post-implantation CTs. Manual localization of electrodes requires time and expertise. To automate this process, our group has proposed automatic techniques that have been validated on CTs acquired with scanners that produce images with an extended range of intensity values. However, there are many clinical CTs acquired with a limited intensity range. This limitation complicates the electrode localization process. In this work, we present a pre-processing step for CTs with a limited intensity range and extend the methods we proposed for full intensity range CTs to localize CI electrodes in CTs with limited intensity range. We evaluate our method on CTs of 20 subjects implanted with CI arrays produced by different manufacturers. Our method achieves a mean localization error of 0.21mm. This indicates our method is robust for automatic localization of CI electrodes in different types of CTs, which represents a crucial step for translating IGCIP from research laboratory to clinical use.

  14. Ranging Behaviour of Commercial Free-Range Laying Hens

    Directory of Open Access Journals (Sweden)

    Leonard Ikenna Chielo

    2016-04-01

    Full Text Available In this study, the range use and behaviour of laying hens in commercial free-range flocks was explored. Six flocks were each visited on four separate days and data collected from their outdoor area (divided into zones based on distance from shed and available resources. These were: apron (0–10 m from shed normally without cover or other enrichments; enriched belt (10–50 m from shed where resources such as manmade cover, saplings and dust baths were provided; and outer range (beyond 50 m from shed with no cover and mainly grass pasture. Data collection consisted of counting the number of hens in each zone and recording behaviour, feather condition and nearest neighbour distance (NND of 20 birds per zone on each visit day. In addition, we used techniques derived from ecological surveys to establish four transects perpendicular to the shed, running through the apron, enriched belt and outer range. Number of hens in each 10 m × 10 m quadrat was recorded four times per day as was the temperature and relative humidity of the outer range. On average, 12.5% of hens were found outside. Of these, 5.4% were found in the apron; 4.3% in the enriched zone; and 2.8% were in the outer range. This pattern was supported by data from quadrats, where the density of hens sharply dropped with increasing distance from shed. Consequently, NND was greatest in the outer range, least in the apron and intermediate in the enriched belt. Hens sampled in outer range and enriched belts had better feather condition than those from the apron. Standing, ground pecking, walking and foraging were the most commonly recorded activities with standing and pecking most likely to occur in the apron, and walking and foraging more common in the outer range. Use of the outer range declined with lower temperatures and increasing relative humidity, though use of apron and enriched belt was not affected by variation in these measures. These data support previous findings that outer range

  15. Ranging Behaviour of Commercial Free-Range Laying Hens.

    Science.gov (United States)

    Chielo, Leonard Ikenna; Pike, Tom; Cooper, Jonathan

    2016-04-26

    In this study, the range use and behaviour of laying hens in commercial free-range flocks was explored. Six flocks were each visited on four separate days and data collected from their outdoor area (divided into zones based on distance from shed and available resources). These were: apron (0-10 m from shed normally without cover or other enrichments); enriched belt (10-50 m from shed where resources such as manmade cover, saplings and dust baths were provided); and outer range (beyond 50 m from shed with no cover and mainly grass pasture). Data collection consisted of counting the number of hens in each zone and recording behaviour, feather condition and nearest neighbour distance (NND) of 20 birds per zone on each visit day. In addition, we used techniques derived from ecological surveys to establish four transects perpendicular to the shed, running through the apron, enriched belt and outer range. Number of hens in each 10 m × 10 m quadrat was recorded four times per day as was the temperature and relative humidity of the outer range. On average, 12.5% of hens were found outside. Of these, 5.4% were found in the apron; 4.3% in the enriched zone; and 2.8% were in the outer range. This pattern was supported by data from quadrats, where the density of hens sharply dropped with increasing distance from shed. Consequently, NND was greatest in the outer range, least in the apron and intermediate in the enriched belt. Hens sampled in outer range and enriched belts had better feather condition than those from the apron. Standing, ground pecking, walking and foraging were the most commonly recorded activities with standing and pecking most likely to occur in the apron, and walking and foraging more common in the outer range. Use of the outer range declined with lower temperatures and increasing relative humidity, though use of apron and enriched belt was not affected by variation in these measures. These data support previous findings that outer range areas tend to be

  16. Extended time-interval analysis

    DEFF Research Database (Denmark)

    Fynbo, Hans Otto Uldall; Riisager, Karsten

    2014-01-01

    Several extensions of the halflife analysis method recently suggested by Horvat and Hardy are put forward. Goodness-of-fit testing is included, and the method is extended to cases where more information is available for each decay event which allows applications also for e.g. γ decay data. The re...

  17. Extended duration orbiter (EDO) insignia

    Science.gov (United States)

    1990-01-01

    Extended duration orbiter (EDO) insignia incorporates a space shuttle orbiter with payload bay doors (PLBDs) open and a spacelab module inside. Trailing the orbiter are the initials EDO. The EDO-modified Columbia, Orbiter Vehicle (OV) 102, will be flown for the first EDO mission, STS-50.

  18. Extended Duration Orbiter Medical Project

    Science.gov (United States)

    Leach, C. S.; Pool, S. L.; Sawin, C. F.; Nicogossian, A. E.

    1990-01-01

    The Extended Duration Orbiter (EDO) program addresses a need for more time to perform experiments and other tasks during Space Shuttle missions. As a part of this program, the Extended Duration Orbiter Medical Project (EDOMP) has been instituted to obtain information about physiologic effects of extending mission duration and the effectiveness of countermeasures against factors that might compromise crew health, safety, or performance on extended-duration missions. Only those investigations that address and characterize operational problems, develop countermeasures, or evaluate the effectiveness of countermeasures will be pursued. The EDOMP investigations will include flight-associated Detailed Supplementary Objectives as well as ground-based studies simulating the influence of microgravity. Investigator teams have been formed in the following areas: biomedical physiology, cardiovascular and fluid/electrolyte physiology, environmental health, muscle and exercise physiology, and neurophysiology. Major operational questions must be answered in each of these areas, and investigations have been designed to answer them. The EDO program will proceed only after countermeasures have been shown to be effective in preventing or mitigating the adverse changes they have been designed to attenuate. The program is underway and will continue on each Shuttle flight as the manifest builds toward a 16-day orbital flight.

  19. Applying and extending Oracle Spatial

    CERN Document Server

    Simon Gerard Greener, Siva Ravada

    2013-01-01

    This book is an advanced practical guide to applying and extending Oracle Spatial.This book is for existing users of Oracle and Oracle Spatial who have, at a minimum, basic operational experience of using Oracle or an equivalent database. Advanced skills are not required.

  20. Millimicrosecond pulse techniques

    CERN Document Server

    Lewis, Ian A D

    1959-01-01

    Millimicrosecond Pulse Techniques, Second Edition focuses on millimicrosecond pulse techniques and the development of devices of large bandwidth, extending down to comparatively low frequencies (1 Mc/s). Emphasis is on basic circuit elements and pieces of equipment of universal application. Specific applications, mostly in the field of nuclear physics instrumentation, are considered. This book consists of eight chapters and opens with an introduction to some of the terminology employed by circuit engineers as well as theoretical concepts, including the laws of circuit analysis, Fourier analysi

  1. Pricing Extendible Options Using the Fast Fourier Transform

    Directory of Open Access Journals (Sweden)

    Siti Nur Iqmal Ibrahim

    2014-01-01

    Full Text Available This paper applies the fast Fourier transform (FFT approach, within the Black-Scholes framework, to the valuation of options whose time to maturity can be extended to a future date (extendible options. We determine the valuation of the extendible options as sums of expectations of indicator functions, leading to a semianalytic expression for the value of the options over a range of strikes. Compared to Monte Carlo simulation, numerical examples demonstrate that the FFT is both computationally more efficient and higher in accuracy.

  2. Minnesota Pheasant Range

    Data.gov (United States)

    Minnesota Department of Natural Resources — This dataset delineates the spatial range of wild pheasant populations in Minnesota as of 2002 by dividing the MN state boundary into 2 units: pheasant range and...

  3. Substring Range Reporting

    DEFF Research Database (Denmark)

    Bille, Philip; Gørtz, Inge Li

    2014-01-01

    We revisit various string indexing problems with range reporting features, namely, position-restricted substring searching, indexing substrings with gaps, and indexing substrings with intervals. We obtain the following main results. We give efficient reductions for each of the above problems...... to a new problem, which we call substring range reporting. Hence, we unify the previous work by showing that we may restrict our attention to a single problem rather than studying each of the above problems individually. We show how to solve substring range reporting with optimal query time and little...... for substring range reporting generalize to substring range counting and substring range emptiness variants. We also obtain non-trivial time-space trade-offs for these problems. Our bounds for substring range reporting are based on a novel combination of suffix trees and range reporting data structures...

  4. Range Surveillance Using Radio Interferometry and TDOA Techniques Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The proposed innovation will utilize a small network of remote sensors (Figure 2.1) to perform Radio Interferometry (RI) and Time Difference of Arrival (TDOA)...

  5. Close-range sensing techniques in alpine terrain

    NARCIS (Netherlands)

    Rutzinger, Martin; Hoefle, Bernhard; Lindenbergh, R.C.; Oude Elberink, Sander; Pirotti, Francesco; Sailer, Rudolf; Scaioni, Marco; Stoetter, J.; Wujanz, Daniel

    2016-01-01

    Early career researchers such as PhD students are a main driving force of scientific research and are for a large part responsible for research innovation. They work on specialized topics within focused research groups that have a limited number of members, but might also have limited capacity in

  6. Evaluate extended surface exchangers carefully

    Energy Technology Data Exchange (ETDEWEB)

    Ganapathy, V. (ABCO Industries, Inc., Abilene, TX (US))

    1990-10-01

    Various types of fins, such as circumferential, rectangular, pegs and rods are used in heat transfer equipment. Fins can be used inside as well as on the outside of tubes. However, to illustrate the basic facts of heat transfer and how one should evaluate fins, these discussions pertain to circumferential solid or serrated fins used widely in the energy equipment industry. Extended surfaces have the advantage of reducing the size and weight of heat transfer equipment. In addition they can result in lower gas pressure drop, thus reducing the operating costs. This article compares the performance of an evaporator for a heat recovery steam generator (HRSG) using bare and finned tubes. The fact this article brings out is that extended surfaces should be evaluated and purchased based on performance and not based on surface area alone.

  7. Extended Supersymmetries in One Dimension

    Directory of Open Access Journals (Sweden)

    F. Toppan

    2008-01-01

    Full Text Available This work covers part of the material presented at the Advanced Summer School in Prague. It is mostly devoted to the structural properties of Extended Supersymmetries in One Dimension. Several results are presented on the classification of linear, irreducible representations realized on a finite number of time-dependent fields. The connections between supersymmetry transformations, Clifford algebras and division algebras are discussed. A manifestly supersymmetric framework for constructing invariants without using the notion of superfields is presented. A few examples of one-dimensional, N-extended, off-shell invariant sigma models are computed. The relation between supersymmetry transformations and graph theory is outlined. The notion of the fusion algebra of irreps tensor products is presented. The relevance of one-dimensional Supersymmetric Quantum Mechanics as a way to extract information on higher dimensional supersymmetric field theories is discussed. 

  8. Extending a browser C++ simulator

    OpenAIRE

    Segarra Roca, Albert

    2017-01-01

    Getting started in computer programming involves using a number of tools such as editors, compilers, debuggers, and terminals. Learning how to use them can be challenging for programming begginers, and installing them may be demanding for certain organizations such as high schools. C– is a project that aims to bridge this gap by providing an educational C++ development environment that runs in a web browser. The goal of this thesis is to extend and improve the current implement...

  9. Locating and extending livelihoods research

    DEFF Research Database (Denmark)

    Prowse, Martin

    2008-01-01

    Much poverty and development research is not explicit about its methodology or philosophical foundations. Based on the extended case method of Burawoy and the epistemological standpoint of critical realism, this paper discusses a methodological approach for reflexive inductive livelihoods research...... that overcomes the unproductive social science dualism of positivism and social constructivism. The approach is linked to a conceptual framework and a menu of research methods that can be sequenced and iterated in light of research questions....

  10. Evolving extended naive Bayes classifiers

    OpenAIRE

    Klawonn, Frank; Angelov, Plamen

    2006-01-01

    Naive Bayes classifiers are a very simple, but often effective tool for classification problems, although they are based on independence assumptions that do not hold in most cases. Extended naive Bayes classifiers also rely on independence assumptions, but break them down to artificial subclasses, in this way becoming more powerful than ordinary naive Bayes classifiers. Since the involved computations for Bayes classifiers are basically generalised mean value calculations, they easily render ...

  11. Extending lock-in methods: term isolation detection of nonlinear signals.

    Science.gov (United States)

    Jarvis, Thomas W

    2016-08-01

    We show that components of a nonlinear signal can be measured using phase-sensitive detection at unconventional demodulation frequencies, allowing us to isolate individual terms from the signal. To demonstrate this technique, autocorrelation measurements of an ultrafast pulsed laser were performed using two-photon absorption. In this example, the isolation of individual autocorrelation terms may provide internal consistency checks to improve the precision and accuracy of pulse characterization. More generally, this scheme can be extended to a range of nonlinear measurements. As a demonstration, we analyze a three-photon autocorrelation model, showing that many nonlinear signals can be studied with this method. We anticipate that term isolation detection will find application in a broad range of experiments, such as multidimensional Fourier transform spectroscopy or coherent anti-Stokes Raman spectroscopy.

  12. Ispaghula Husk-Based Extended Release Tablets of Diclofenac ...

    African Journals Online (AJOL)

    Purpose: To formulate extended-release tablets of diclofenac sodium based on ispaghula husk. Methods: Tablets with varying proportions of diclofenac sodium and ispaghula husk were formulated by wet granulation technique at a fixed compression force of 10 kN. The formulated tablets were evaluated for ...

  13. Extended depth of field system for long distance iris acquisition

    Science.gov (United States)

    Chen, Yuan-Lin; Hsieh, Sheng-Hsun; Hung, Kuo-En; Yang, Shi-Wen; Li, Yung-Hui; Tien, Chung-Hao

    2012-10-01

    Using biometric signatures for identity recognition has been practiced for centuries. Recently, iris recognition system attracts much attention due to its high accuracy and high stability. The texture feature of iris provides a signature that is unique for each subject. Currently most commercial iris recognition systems acquire images in less than 50 cm, which is a serious constraint that needs to be broken if we want to use it for airport access or entrance that requires high turn-over rate . In order to capture the iris patterns from a distance, in this study, we developed a telephoto imaging system with image processing techniques. By using the cubic phase mask positioned front of the camera, the point spread function was kept constant over a wide range of defocus. With adequate decoding filter, the blurred image was restored, where the working distance between the subject and the camera can be achieved over 3m associated with 500mm focal length and aperture F/6.3. The simulation and experimental results validated the proposed scheme, where the depth of focus of iris camera was triply extended over the traditional optics, while keeping sufficient recognition accuracy.

  14. Self-adhesive microculture system for extended live cell imaging.

    Science.gov (United States)

    Skommer, J; McGuinness, D; Wlodkowic, D

    2011-06-01

    Gas permeable and biocompatible soft polymers are convenient for biological applications. Using the soft polymer poly(dimethylsiloxane) (PDMS), we established a straightforward technique for in-house production of self-adhesive and optical grade microculture devices. A gas permeable PDMS layer effectively protects against medium evaporation, changes in osmolarity, contamination and drug diffusion. These chip-based devices can be used effectively for long term mammalian cell culture and support a range of bioassays used in pharmacological profiling of anti-cancer drugs. Results obtained on a panel of hematopoietic and solid tumor cell lines during screening of investigative anti-cancer agents corresponded well to those obtained in a conventional cell culture on polystyrene plates. The cumulative correlation analysis of multiple cell lines and anti-cancer drugs showed no adverse effects on cell viability or cell growth retardation during microscale static cell culture. PDMS devices also can be custom modified for many bio-analytical purposes and are interfaced easily with both inverted and upright cell imaging platforms. Moreover, PDMS microculture devices are suitable for extended real time cell imaging. Data from the multicolor, real time analysis of apoptosis on human breast cancer MCF-7 cells provided further evidence that elimination of redundant centrifugation/washing achieved during microscale real time analysis facilitates preservation of fragile apoptotic cells and provides dynamic cellular information at high resolution. Because only small reaction volumes are required, such devices offer reduced use of consumables as well as simplified manipulations during all stages of live cell imaging.

  15. Bi-Directional Brillouin Optical Time Domain Analyzer System for Long Range Distributed Sensing.

    Science.gov (United States)

    Guo, Nan; Wang, Liang; Wang, Jie; Jin, Chao; Tam, Hwa-Yaw; Zhang, A Ping; Lu, Chao

    2016-12-16

    We propose and experimentally demonstrate a novel scheme of bi-directional Brillouin time domain analyzer (BD-BOTDA) to extend the sensing range. By deploying two pump-probe pairs at two different wavelengths, the Brillouin frequency shift (BFS) distribution over each half of the whole fiber can be obtained with the simultaneous detection of Brillouin signals in both channels. Compared to the conventional unidirectional BOTDA system of the same sensing range, the proposed BD-BOTDA scheme enables distributed sensing with a performance level comparable to the conventional one with half of the sensing range and a spatial resolution of 2 m, while maintaining the Brillouin signal-to-noise ratio (SNR) and the BFS uncertainty. Based on this technique, we have achieved distributed temperature sensing with a measurement range of 81.9 km fiber at a spatial resolution of 2 m and BFS uncertainty of ~0.44 MHz without introducing any complicated components or schemes.

  16. Applying SPAM to the extended MWA

    Science.gov (United States)

    Hurley-Walker, N.; Intema, H.

    2017-01-01

    The extended baselines of the MWA move the instrument into a more difficult calibration and imaging regime, where the more widely-separated antennas are more likely to view the sky through different ionospheric conditions, leading to differential refractive effects over the array. Current extrapolations by Trott, Jordan, and Hurley-Walker imply that the diffractive scale will remain larger than the longest baseline for 50-70% of observations, but these are extrapolations only. Other instruments have performed observations with baselines longer than the diffractive scale, and used software techniques to mitigate the ionospheric distortions. One such survey is the Tata Institute of Fundamental Research Giant Metrewave Radio Telescope Sky Survey (TGSS) at 150 MHz. Intema et al. (2016) used the Source Peeling & Atmospheric Modeling (SPAM) software to produce a catalogue of over 600,000 sources from data that had previously been slow and difficult to process. This proposal is for a short series of observations to test the usage of the SPAM software on the extended MWA, and to find the optimal observing parameters for its use. If successful, this could assist other groups in effectively utilising the long baselines.

  17. Complete Solutions to Extended Stokes' Problems

    Directory of Open Access Journals (Sweden)

    Chi-Min Liu

    2008-01-01

    Full Text Available The main object of the present study is to theoretically solve the viscous flow of either a finite or infinite depth, which is driven by moving plane(s. Such a viscous flow is usually named as Stokes' first or second problems, which indicates the fluid motion driven by the impulsive or oscillating motion of the boundary, respectively. Traditional Stokes' problems are firstly revisited, and three extended problems are subsequently examined. Using some mathematical techniques and integral transforms, complete solutions which can exactly capture the flow characteristics at any time are derived. The corresponding steady-state and transient solutions are readily determined on the basis of complete solutions. Current results have wide applications in academic researches and are of significance for future studies taking more boundary conditions and non-Newtonian fluids into account.

  18. Optical flow computation using extended constraints.

    Science.gov (United States)

    Del Bimbo, A; Nesi, P; Sanz, J C

    1996-01-01

    Several approaches for optical flow estimation use partial differential equations to model changes in image brightness throughout time. A commonly used equation is the so-called optical flow constraint (OFC), which assumes that the image brightness is stationary with respect to time. More recently, a different constraint referred to as the extended optical flow constraint (EOFC) has been introduced, which also contains the divergence of the flow field of image brightness. There is no agreement in the literature about which of these constraints provides the best estimation of the velocity field. Two new solutions for optical flow computation are proposed, which are based on an approximation of the constraint equations. The two techniques have been used with both EOFC and OFC constraint equations. Results achieved by using these solutions have been compared with several well-known computational methods for optical flow estimation in different motion conditions. Estimation errors have also been measured and compared for different types of motion.

  19. Extending OLAP Querying to External Object

    DEFF Research Database (Denmark)

    Pedersen, Torben Bach; Shoshani, Arie; Gu, Junmin

    inherent in data in nonstandard applications are not accommodated well by OLAP systems. In contrast, object database systems are built to handle such complexity, but do not support OLAP-type querying well. This paper presents the concepts and techniques underlying a flexible, multi-model federated system...... that enables OLAP users to exploit simultaneously the features of OLAP and object systems. The system allows data to be handled using the most appropriate data model and technology: OLAP systems for dimensional data and object database systems for more complex, general data. Additionally, physical data...... integration can be avoided. As a vehicle for demonstrating the capabilities of the system, a prototypical OLAP language is defined and extended to naturally support queries that involve data in object databases. The language permits selection criteria that reference object data, queries that return...

  20. Substring Range Reporting

    DEFF Research Database (Denmark)

    Bille, Philip; Gørtz, Inge Li

    2011-01-01

    We revisit various string indexing problems with range reporting features, namely, position-restricted substring searching, indexing substrings with gaps, and indexing substrings with intervals. We obtain the following main results. – We give efficient reductions for each of the above problems...... to a new problem, which we call substring range reporting. Hence, we unify the previous work by showing that we may restrict our attention to a single problem rather than studying each of the above problems individually. – We show how to solve substring range reporting with optimal query time and little...... range reporting are based on a novel combination of suffix trees and range reporting data structures. The reductions are simple and general and may apply to other combinations of string indexing with range reporting....

  1. Compact Antenna Range

    Data.gov (United States)

    Federal Laboratory Consortium — Facility consists of a folded compact antenna range including a computer controlled three axis position table, parabolic reflector and RF sources for the measurement...

  2. Dryden Aeronautical Test Range

    Data.gov (United States)

    Federal Laboratory Consortium — Recently redesignated to honor Dr. Hugh L. Dryden, NASA's Dryden Aeronautical Test Range (DATR) supports aerospace flight research and technology integration, space...

  3. Ranging Behaviour of Commercial Free-Range Laying Hens

    Science.gov (United States)

    Chielo, Leonard Ikenna; Pike, Tom; Cooper, Jonathan

    2016-01-01

    to the shed in free-range flocks. This study suggests that hens in the outer range engaged more in walking and foraging activities and showed signs of better welfare than those closer to the shed. Abstract In this study, the range use and behaviour of laying hens in commercial free-range flocks was explored. Six flocks were each visited on four separate days and data collected from their outdoor area (divided into zones based on distance from shed and available resources). These were: apron (0–10 m from shed normally without cover or other enrichments); enriched belt (10–50 m from shed where resources such as manmade cover, saplings and dust baths were provided); and outer range (beyond 50 m from shed with no cover and mainly grass pasture). Data collection consisted of counting the number of hens in each zone and recording behaviour, feather condition and nearest neighbour distance (NND) of 20 birds per zone on each visit day. In addition, we used techniques derived from ecological surveys to establish four transects perpendicular to the shed, running through the apron, enriched belt and outer range. Number of hens in each 10 m × 10 m quadrat was recorded four times per day as was the temperature and relative humidity of the outer range. On average, 12.5% of hens were found outside. Of these, 5.4% were found in the apron; 4.3% in the enriched zone; and 2.8% were in the outer range. This pattern was supported by data from quadrats, where the density of hens sharply dropped with increasing distance from shed. Consequently, NND was greatest in the outer range, least in the apron and intermediate in the enriched belt. Hens sampled in outer range and enriched belts had better feather condition than those from the apron. Standing, ground pecking, walking and foraging were the most commonly recorded activities with standing and pecking most likely to occur in the apron, and walking and foraging more common in the outer range. Use of the outer range declined with lower

  4. Bifurcations in a Generalization of the ZAD Technique: Application to a DC-DC Buck Power Converter

    Directory of Open Access Journals (Sweden)

    Ludwing Torres

    2012-01-01

    Full Text Available A variation of ZAD technique is proposed, which is to extend the range of zero averaging of the switching surface (in the classic ZAD it is taken in a sampling period, to a number of sampling periods. This has led to a technique that has been named -ZAD. Assuming a specific value for =2, we have studied the 2-ZAD technique. The latter has presented better results in terms of stability, regarding the original ZAD technique. These results can be demonstrated in different state space graphs and bifurcation diagrams, which have been calculated based on the analysis done about the behavior of this new strategy.

  5. Range Scheduling Aid (RSA)

    Science.gov (United States)

    Logan, J. R.; Pulvermacher, M. K.

    1991-01-01

    Range Scheduling Aid (RSA) is presented in the form of the viewgraphs. The following subject areas are covered: satellite control network; current and new approaches to range scheduling; MITRE tasking; RSA features; RSA display; constraint based analytic capability; RSA architecture; and RSA benefits.

  6. Departies: conceptualizing extended youth parties

    DEFF Research Database (Denmark)

    Fjær, Eivind Grip; Tutenges, Sébastien

    2017-01-01

    -taking behaviors, such as drug use and violence. Here, we scrutinize the research on extended youth parties to identify general changes that young people undergo at these events. We call these celebrations departies, because they center on the organization and facilitation of momentary departures from...... immoral; (4) stylistically, by altering their stylistic expressions through dress, demeanor, and consumption; and (5) experientially, because the parties generate mood and mind alterations. These are overlapping and intertwined elements, the combination of which amounts to a distinct type of youth party...

  7. Home range and travels

    Science.gov (United States)

    Stickel, L.F.; King, John A.

    1968-01-01

    The concept of home range was expressed by Seton (1909) in the term 'home region,' which Burr (1940, 1943) clarified with a definition of home range and exemplified in a definitive study of Peromyscus in the field. Burt pointed out the ever-changing characteristics of home-range area and the consequent absence of boundaries in the usual sense--a finding verified by investigators thereafter. In the studies summarized in this paper, sizes of home ranges of Peromyscus varied within two magnitudes, approximately from 0.1 acre to ten acres, in 34 studies conducted in a variety of habitats from the seaside dunes of Florida to the Alaskan forests. Variation in sizes of home ranges was correlated with both environmental and physiological factors; with habitat it was conspicuous, both in the same and different regions. Food supply also was related to size of home range, both seasonally and in relation to habitat. Home ranges generally were smallest in winter and largest in spring, at the onset of the breeding season. Activity and size also were affected by changes in weather. Activity was least when temperatures were low and nights were bright. Effects of rainfall were variable. Sizes varied according to sex and age; young mice remained in the parents' range until they approached maturity, when they began to travel more widely. Adult males commonly had larger home ranges than females, although there were a number of exceptions. An inverse relationship between population density and size of home range was shown in several studies and probably is the usual relationship. A basic need for activity and exploration also appeared to influence size of home range. Behavior within the home range was discussed in terms of travel patterns, travels in relation to home sites and refuges, territory, and stability of size of home range. Travels within the home range consisted of repeated use of well-worn trails to sites of food, shelter, and refuge, plus more random exploratory travels

  8. An Observability Metric for Underwater Vehicle Localization Using Range Measurements

    Science.gov (United States)

    Arrichiello, Filippo; Antonelli, Gianluca; Aguiar, Antonio Pedro; Pascoal, Antonio

    2013-01-01

    The paper addresses observability issues related to the general problem of single and multiple Autonomous Underwater Vehicle (AUV) localization using only range measurements. While an AUV is submerged, localization devices, such as Global Navigation Satellite Systems, are ineffective, due to the attenuation of electromagnetic waves. AUV localization based on dead reckoning techniques and the use of affordable motion sensor units is also not practical, due to divergence caused by sensor bias and drift. For these reasons, localization systems often build on trilateration algorithms that rely on the measurements of the ranges between an AUV and a set of fixed transponders using acoustic devices. Still, such solutions are often expensive, require cumbersome calibration procedures and only allow for AUV localization in an area that is defined by the geometrical arrangement of the transponders. A viable alternative for AUV localization that has recently come to the fore exploits the use of complementary information on the distance from the AUV to a single transponder, together with information provided by on-board resident motion sensors, such as, for example, depth, velocity and acceleration measurements. This concept can be extended to address the problem of relative localization between two AUVs equipped with acoustic sensors for inter-vehicle range measurements. Motivated by these developments, in this paper, we show that both the problems of absolute localization of a single vehicle and the relative localization of multiple vehicles can be treated using the same mathematical framework, and tailoring concepts of observability derived for nonlinear systems, we analyze how the performance in localization depends on the types of motion imparted to the AUVs. For this effect, we propose a well-defined observability metric and validate its usefulness, both in simulation and by carrying out experimental tests with a real marine vehicle during which the performance of an

  9. An Observability Metric for Underwater Vehicle Localization Using Range Measurements

    Directory of Open Access Journals (Sweden)

    Filippo Arrichiello

    2013-11-01

    Full Text Available The paper addresses observability issues related to the general problem of single and multiple Autonomous Underwater Vehicle (AUV localization using only range measurements. While an AUV is submerged, localization devices, such as Global Navigation Satellite Systems, are ineffective, due to the attenuation of electromagnetic waves. AUV localization based on dead reckoning techniques and the use of affordable motion sensor units is also not practical, due to divergence caused by sensor bias and drift. For these reasons, localization systems often build on trilateration algorithms that rely on the measurements of the ranges between an AUV and a set of fixed transponders using acoustic devices. Still, such solutions are often expensive, require cumbersome calibration procedures and only allow for AUV localization in an area that is defined by the geometrical arrangement of the transponders. A viable alternative for AUV localization that has recently come to the fore exploits the use of complementary information on the distance from the AUV to a single transponder, together with information provided by on-board resident motion sensors, such as, for example, depth, velocity and acceleration measurements. This concept can be extended to address the problem of relative localization between two AUVs equipped with acoustic sensors for inter-vehicle range measurements. Motivated by these developments, in this paper, we show that both the problems of absolute localization of a single vehicle and the relative localization of multiple vehicles can be treated using the same mathematical framework, and tailoring concepts of observability derived for nonlinear systems, we analyze how the performance in localization depends on the types of motion imparted to the AUVs. For this effect, we propose a well-defined observability metric and validate its usefulness, both in simulation and by carrying out experimental tests with a real marine vehicle during which the

  10. Nonlinear dynamic range compression deconvolution

    Science.gov (United States)

    Haji-Saeed, Bahareh; Sengupta, Sandip K.; Goodhue, William; Khoury, Jed; Woods, Charles L.; Kierstead, John

    2006-07-01

    We introduce a dynamic range image compression technique for nonlinear deconvolution; the impulse response of the distortion function and the noisy distorted image are jointly transformed to pump a clean reference beam in a two-beam coupling arrangement. The Fourier transform of the pumped reference beam contains the deconvolved image and its conjugate. In contrast to standard deconvolution approaches, for which noise can be a limiting factor in the performance, this approach allows the retrieval of distorted signals embedded in a very high-noise environment.

  11. Preoperative venogram in planning extended craniectomies

    Energy Technology Data Exchange (ETDEWEB)

    Lanzieri, C.F.; Duchesneau, P.M.; Rosenbloom, S.A.; Weinstein, M.A.; Sacher, M.

    1987-07-01

    A technique of extended craniectomy sometimes allows removal of large central or transtentorial mass lesions at a single operative sitting because it affords better exposure and control of normal structures. While seeking to avoid multiple craniotomies, this method requires permanent ligation of the transverse venous sinus. Unless there is adequate collateral venous drainage from the ipsilateral hemisphere, the patient is at risk for venous infarction in the post-craniectomy period. The purpose of this study is to propose a method of establishing the presence of collateral venous drainage preoperatively. Each carotid artery is injected with the head in a neutral position and with the head turned to the side ipsilateral to the carotid artery injection in an attempt to divert the venous flow. Fifty patients were examined using this method; seven were being evaluated for possible craniectomies. The technique identified nine patients with potential venous collaterals (20%). They would otherwise have been considered nonoperable: two of the six patients eventually operated upon (33%) fell into this category. In general, the operative procedure may be safe more often on the left than the right (45%) vs (20%). Particular attention must be given to the pattern of venous drainage from the posterior temporal lobe to avoid isolation of the venous drainage from this area.

  12. New data structures for orthogonal range searching

    DEFF Research Database (Denmark)

    Alstrup, Stephen; Brodal, Gerth Stølting; Rauhe, Theis

    2000-01-01

    We present new general techniques for static orthogonal range searching problems in two and higher dimensions. For the general range reporting problem in R3, we achieve query time O(log n+k) using space O(n log1+ε n), where n denotes the number of stored points and k the number of points to be re...

  13. Acquired Techniques

    DEFF Research Database (Denmark)

    Lunde Nielsen, Espen; Halse, Karianne

    2013-01-01

    Acquired Techniques - a Leap into the Archive, at Aarhus School of Architecture. In collaboration with Karianne Halse, James Martin and Mika K. Friis. Following the footsteps of past travelers this is a journey into tools and techniques of the architectural process. The workshop will focus upon...

  14. Local Information from Range-Speed Radar Sequences

    NARCIS (Netherlands)

    Dorp, Ph. van; Groen, F.C.A.

    2007-01-01

    Radar observes targets, but they remain difficult to interpret due to the difficulty in analysing the radar range-speed sequences. The need for accurate analyses tools increases in case of extended target behaviour or multiple channel radars which give additional observation angles. Extended targets

  15. Optimization techniques in statistics

    CERN Document Server

    Rustagi, Jagdish S

    1994-01-01

    Statistics help guide us to optimal decisions under uncertainty. A large variety of statistical problems are essentially solutions to optimization problems. The mathematical techniques of optimization are fundamentalto statistical theory and practice. In this book, Jagdish Rustagi provides full-spectrum coverage of these methods, ranging from classical optimization and Lagrange multipliers, to numerical techniques using gradients or direct search, to linear, nonlinear, and dynamic programming using the Kuhn-Tucker conditions or the Pontryagin maximal principle. Variational methods and optimiza

  16. Long range image enhancement

    CSIR Research Space (South Africa)

    Duvenhage, B

    2015-11-01

    Full Text Available and Vision Computing, Auckland, New Zealand, 23-24 November 2015 Long Range Image Enhancement Bernardt Duvenhage Council for Scientific and Industrial Research South Africa Email: bduvenhage@csir.co.za Abstract Turbulent pockets of air...

  17. SNOWY RANGE WILDERNESS, WYOMING.

    Science.gov (United States)

    Houston, Robert S.; Bigsby, Philip R.

    1984-01-01

    A mineral survey of the Snowy Range Wilderness in Wyoming was undertaken and was followed up with more detailed geologic and geochemical surveys, culminating in diamond drilling of one hole in the Snowy Range Wilderness. No mineral deposits were identified in the Snowy Range Wilderness, but inasmuch as low-grade uranium and associated gold resources were identified in rocks similar to those of the northern Snowy Range Wilderness in an area about 5 mi northeast of the wilderness boundary, the authors conclude that the northern half of the wilderness has a probable-resource potential for uranium and gold. Closely spaced drilling would be required to completely evaluate this mineral potential. The geologic terrane precludes the occurrence of fossil fuels.

  18. Atlantic Test Range (ATR)

    Data.gov (United States)

    Federal Laboratory Consortium — ATR controls fully-instrumented and integrated test ranges that provide full-service support for cradle-to-grave testing. Airspace and surface target areas are used...

  19. Light Detection And Ranging

    Data.gov (United States)

    U.S. Geological Survey, Department of the Interior — LiDAR (Light Detection and Ranging) discrete-return point cloud data are available in the American Society for Photogrammetry and Remote Sensing (ASPRS) LAS format....

  20. Analysis of RTM extended images for VTI media

    KAUST Repository

    Li, Vladimir

    2016-04-28

    Extended images obtained from reverse time migration (RTM) contain information about the accuracy of the velocity field and subsurface illumination at different incidence angles. Here, we evaluate the influence of errors in the anisotropy parameters on the shape of the residual moveout (RMO) in P-wave RTM extended images for VTI (transversely isotropic with a vertical symmetry axis) media. Using the actual spatial distribution of the zero-dip NMO velocity (Vnmo), which could be approximately estimated by conventional techniques, we analyze the extended images obtained with distorted fields of the parameters η and δ. Differential semblance optimization (DSO) and stack-power estimates are employed to study the sensitivity of focusing to the anisotropy parameters. We also build angle gathers to facilitate interpretation of the shape of RMO in the extended images. The results show that the signature of η is dip-dependent, whereas errors in δ cause defocusing only if that parameter is laterally varying. Hence, earlier results regarding the influence of η and δ on reflection moveout and migration velocity analysis remain generally valid in the extended image space for complex media. The dependence of RMO on errors in the anisotropy parameters provides essential insights for anisotropic wavefield tomography using extended images.

  1. Extended ankle and foot fasciotomy as an enhancement to the surgical treatment of patients with prolonged ischemia of the lower extremities

    Directory of Open Access Journals (Sweden)

    Mišović Sidor

    2005-01-01

    Full Text Available Aim. To present the technique and efficacy of extended ankle and foot fasciotomy, as a surgical limb-salvage procedure associated with the successful revascularization after the gold interval. Method. A retrospective review of six patients at the age of 16−79 years (mean 39 in the period from 1996 to 2003, treated with the extended ankle and foot fasciotomy. There were four males undergoing the delayed treatment of war injuries to the lower extremity, and two females with atherosclerotic occlusive disease (a. illiacae dex and a. poplitealis dex.. The average ishemic time in the wounded patients was 22 hours (range, 14−30 hours, and ischemic time in occlusive disease (range, 48−72 hours. Clinical signs, indications, surgical access and the technique of extended ankle and foot fasciotomy was reported. Results. The obtained results were classified as early and late. There was no cases with lethal outcome. Incisional wounds closed 15 days after the intervention, using secondary suture or skin transplant sec. Thiersch. The satisfactory functional results were achieved in 4 of the patients, 1 had a small edema, while amputation was performed in 1 patient. Conclusion. In cases of prolonged foot ischemia with edema and paresthesia in the toes, extended ankle and foot fasciotomy should be performed as a surgical limb-salvage procedure.

  2. Supersymmetric inversion of effective-range expansions

    OpenAIRE

    Midya, Bikashkali; Evrard, Jérémie; Abramowicz, Sylvain; Ramirez Suarez, Oscar Leonardo; Sparenberg, Jean-Marc

    2015-01-01

    A complete and consistent inversion technique is proposed to derive an accurate interaction potential from an effective-range function for a given partial wave in the neutral case. First, the effective-range function is Taylor or Pad\\'e expanded, which allows high precision fitting of the experimental scattering phase shifts with a minimal number of parameters on a large energy range. Second, the corresponding poles of the scattering matrix are extracted in the complex wave-number plane. Thir...

  3. Preliminary experience of fractionated stereotactic radiosurgery with extend system of Gamma Knife

    Directory of Open Access Journals (Sweden)

    Raj Bisht

    2016-03-01

    Full Text Available Purpose: The purpose of this study is to present multisession stereotactic radiosurgery with initial experience using custom made extend system (ES of Gamma Knife.Methods: The ES is comprised of a carbon fiber frame also called extend frame, vacuum head rest cushion, patient surveillance unit and a configurable front piece with dental impression tray. The extend frame is a rigid connection between patient's head and patient positioning system (PPS of Gamma Knife. A dental impression of patient was created and attached to the frontal piece of extend system. The treatment setup involves positioning the patient within the extend frame using patient specific headrest cushion and front piece. The reference patient’s head position was recorded through measurements of repositioning check tool (RCT apertures using a high precision digital probe before computed tomography (CT scan. The RCT measurements taken before treatment were compared with recorded reference position to ensure appropriate patient treatment position. Volumetric magnetic resonance (MR scan was co-registered with stereotactic CT scan on Leksell Gamma plan. Fused MR to CT images on Gamma Plan was utilized to delineate regions of interest and prepare a precise treatment plan. The presented study includes positional reproducibility check and dosimetric evaluation of ten patients treated with ES.Results: Forty-three fractions on ten patients with prescribed treatment format were delivered successfully. An average tumor volume of 11.26 cm3 (range, 340 mm3 to 59.12 cm3 was treated with ES. The mean tumor coverage of 91.91% (range, 90% to 95% was able to achieve at 50% prescription isodose without compromising adjacent normal structure radiation dose tolerances. The mean inter-fraction positional variation of 0.69 mm influences an inherent strength of immobilization technique. Follow-up of seven patients at a median interval of 16 months (range, 9 months to 26 months showed evidence of 100

  4. Extended uncertainty from first principles

    Energy Technology Data Exchange (ETDEWEB)

    Costa Filho, Raimundo N., E-mail: rai@fisica.ufc.br [Departamento de Física, Universidade Federal do Ceará, Caixa Postal 6030, Campus do Pici, 60455-760 Fortaleza, Ceará (Brazil); Braga, João P.M., E-mail: philipe@fisica.ufc.br [Instituto de Ciências Exatas e da Natureza-ICEN, Universidade da Integração Internacional da Lusofonia Afro-Brasileira-UNILAB, Campus dos Palmares, 62785-000 Acarape, Ceará (Brazil); Lira, Jorge H.S., E-mail: jorge.lira@mat.ufc.br [Departamento de Matemática, Universidade Federal do Ceará, Caixa Postal 6030, Campus do Pici, 60455-760 Fortaleza, Ceará (Brazil); Andrade, José S., E-mail: soares@fisica.ufc.br [Departamento de Física, Universidade Federal do Ceará, Caixa Postal 6030, Campus do Pici, 60455-760 Fortaleza, Ceará (Brazil)

    2016-04-10

    A translation operator acting in a space with a diagonal metric is introduced to describe the motion of a particle in a quantum system. We show that the momentum operator and, as a consequence, the uncertainty relation now depend on the metric. It is also shown that, for any metric expanded up to second order, this formalism naturally leads to an extended uncertainty principle (EUP) with a minimum momentum dispersion. The Ehrenfest theorem is modified to include an additional term related to a tidal force arriving from the space curvature introduced by the metric. For one-dimensional systems, we show how to map a harmonic potential to an effective potential in Euclidean space using different metrics.

  5. Center for Extended Magnetohydrodynamics Modeling

    Energy Technology Data Exchange (ETDEWEB)

    Ramos, Jesus [Massachusetts Inst. of Technology (MIT), Cambridge, MA (United States)

    2017-02-14

    This researcher participated in the DOE-funded Center for Extended Magnetohydrodynamics Modeling (CEMM), a multi-institutional collaboration led by the Princeton Plasma Physics Laboratory with Dr. Stephen Jardin as the overall Principal Investigator. This project developed advanced simulation tools to study the non-linear macroscopic dynamics of magnetically confined plasmas. The collaborative effort focused on the development of two large numerical simulation codes, M3D-C1 and NIMROD, and their application to a wide variety of problems. Dr. Ramos was responsible for theoretical aspects of the project, deriving consistent sets of model equations applicable to weakly collisional plasmas and devising test problems for verification of the numerical codes. This activity was funded for twelve years.

  6. Hamiltonian dynamics of extended objects

    Energy Technology Data Exchange (ETDEWEB)

    Capovilla, R [Departamento de FIsica, Centro de Investigacion y de Estudios Avanzados del IPN, Apdo Postal 14-740, 07000 Mexico, DF (Mexico); Guven, J [School of Theoretical Physics, Dublin Institute for Advanced Studies, 10 Burlington Road, Dublin 4 (Ireland); Rojas, E [Instituto de Ciencias Nucleares, Universidad Nacional Autonoma de Mexico, Apdo Postal 70-543, 04510 Mexico, DF (Mexico)

    2004-12-07

    We consider relativistic extended objects described by a reparametrization-invariant local action that depends on the extrinsic curvature of the worldvolume swept out by the object as it evolves. We provide a Hamiltonian formulation of the dynamics of such higher derivative models which is motivated by the ADM formulation of general relativity. The canonical momenta are identified by looking at boundary behaviour under small deformations of the action; the relationship between the momentum conjugate to the embedding functions and the conserved momentum density is established. The canonical Hamiltonian is constructed explicitly; the constraints on the phase space, both primary and secondary, are identified and the role they play in the theory is described. The multipliers implementing the primary constraints are identified in terms of the ADM lapse and shift variables and Hamilton's equations are shown to be consistent with the Euler-Lagrange equations.

  7. Extended mission life support systems

    Science.gov (United States)

    Quattrone, P. D.

    1985-01-01

    Extended manned space missions which include interplanetary missions require regenerative life support systems. Manned mission life support considerations are placed in perspective and previous manned space life support system technology, activities and accomplishments in current supporting research and technology (SR&T) programs are reviewed. The life support subsystem/system technologies required for an enhanced duration orbiter (EDO) and a space operations center (SOC), regenerative life support functions and technology required for manned interplanetary flight vehicles, and future development requirements are outlined. The Space Shuttle Orbiters (space transportation system) is space cabin atmosphere is maintained at Earth ambient pressure of 14.7 psia (20% O2 and 80% N2). The early Shuttle flights will be seven-day flights, and the life support system flight hardware will still utilize expendables.

  8. Extended Fundamental Model of Resonance

    Science.gov (United States)

    Breiter, Sławomir

    2003-03-01

    Fundamental models are the simplest, one degree of freedom Hamiltonians that serve as a tool to understand the qualitative effects of various resonances. A new, extended fundamental model (EFM) is proposed in order to improve the classical, Andoyer type, second fundamental model (SFM). The EFM Hamiltonian differs from the SFM by the addition of a term with the third power of momentum; it depends on two free parameters. The new model is studied for the case of a first-order resonance, where up to five critical points can be present. Similarly, to the respective SFM, it admits only the saddle-node bifurcations of critical points, but its advantage lies in the capability of generating the separatrix bifurcations, known also as saddle connections. The reduction of parameters for the EFM has been performed in a way that allows the use of the model in the case of the so-called abnormal resonance.

  9. Catalytic distillation extends its reach

    Energy Technology Data Exchange (ETDEWEB)

    Rock, K.; McGuirk, T. [Catalytic Distillation Technologies, Houston, TX (United States); Gildert, G.R. [Catalytic Distillation Technologies, Pasadena, TX (United States)

    1997-07-01

    Since the early 1980s, catalytic distillation processes have been selected by more than a hundred operators for various applications. Since such a unit performs both reaction and distillation simultaneously, a combined column can replace a separate, fixed-bed reactor and distillation column, thereby eliminating equipment and reducing capital costs. And, compared to the conventional approach, catalytic distillation may also improve other factors, such as reactant conversion, selectivity, mass transfer, operating pressure, oligomer formation and catalyst fouling. The constant washing of the catalyst by liquid flowing down the column and the distillation of high-boiling foulants results in extended catalyst life. Four selective hydrogenation applications of catalytic distillation are discussed: Butadiene selective hydrogenation combined within an MTBE unit; Pentadiene selective hydrogenation; C{sub 4} acetylene conversion; and Benzene saturation.

  10. Oral hydromorphone extended-release.

    Science.gov (United States)

    Guay, David R P

    2010-12-01

    To review the chemistry, pharmacodynamics, pharmacokinetics, efficacy, tolerability, dosing, and role of the Osmotic-controlled Release Oral delivery System (OROS) hydromorphone extended-release (ER) tablets. A MEDLINE/PUBMED search (1986-August 2010) was conducted to identify studies in the English language, with additional references being obtained from their bibliographies. All studies of hydromorphone ER were reviewed. This is the second long-acting hydromorphone formulation to receive approval by the Food and Drug Administration (a twice-daily formulation was approved in September 2004, but was subsequently withdrawn in July 2005). Hydromorphone is a semi-synthetic mu-opioid receptor agonist structurally similar to morphine, hydrocodone, and oxymorphone. OROS ER technology allows once-daily dosing. Clinical trials have focused on the convertibility of (an) other opioid(s) to hydromorphone ER in chronic malignant and nonmalignant pain. This product displays the expected opioid side effects, being comparable to oxycodone controlled-release. Coadministration with ethanol does not produce the degree of "dose-dumping" seen with the former hydromorphone twice-daily product or oxymorphone ER. Hydromorphone ER is indicated for the management of moderate-to-severe pain in opioidtolerant patients requiring continuous, around-the-clock opioid analgesia for an extended period of time. Dosage adjustment is recommended in patients with moderate hepatic impairment (Child-Pugh class B) and moderate renal impairment (creatinine clearance of 30-60 mL/min). Hydromorphone ER is the newest oral opioid to enter a crowded marketplace now totaling 15 different Schedule 2 opioids (including tapentadol), and tramadol, available in oral, parenteral, rectal, transdermal, transmucosal, and intranasal formulations. It does not appear to have any unique assets or liabilities and should be considered as one of many oral opioids available for the management of persistent pain of moderate

  11. Extending the range of supercritical fluid chromatography by use of water-rich modifiers.

    Science.gov (United States)

    Liu, Jinchu; Regalado, Erik L; Mergelsberg, Ingrid; Welch, Christopher J

    2013-08-14

    In this study we investigate the recently reported use of water-containing modifiers for separation and purification of hydrophilic compounds by supercritical fluid chromatography. Improved peak shape is obtained for a variety of glycosides and otherwise hydrophilic compounds when 5% water is added to the methanol co-solvent used in SFC separations, and examples of the use of this approach in preparative SFC purifications are presented.

  12. Extending the range and physical accuracy of coarse-grained models: Order parameter dependent interactions

    Science.gov (United States)

    Wagner, Jacob W.; Dannenhoffer-Lafage, Thomas; Jin, Jaehyeok; Voth, Gregory A.

    2017-07-01

    Order parameters (i.e., collective variables) are often used to describe the behavior of systems as they capture different features of the free energy surface. Yet, most coarse-grained (CG) models only employ two- or three-body non-bonded interactions between the CG particles. In situations where these interactions are insufficient for the CG model to reproduce the structural distributions of the underlying fine-grained (FG) model, additional interactions must be included. In this paper, we introduce an approach to expand the basis sets available in the multiscale coarse-graining (MS-CG) methodology by including order parameters. Then, we investigate the ability of an additive local order parameter (e.g., density) and an additive global order parameter (i.e., distance from a hard wall) to improve the description of CG models in interfacial systems. Specifically, we study methanol liquid-vapor coexistence, acetonitrile liquid-vapor coexistence, and acetonitrile liquid confined by hard-wall plates, all using single site CG models. We find that the use of order parameters dramatically improves the reproduction of structural properties of interfacial CG systems relative to the FG reference as compared with pairwise CG interactions alone.

  13. Preliminary Performance Evaluation of MEMS-based Piezoelectric Energy Harvesters in Extended Temperature Range

    DEFF Research Database (Denmark)

    Xu, R.; Borregaard, L.M.; Lei, A.

    2012-01-01

    In this work a batch of MEMS-based vibration energy harvesters consisting of a silicon/PZT thick film ntilever with integrated proof mass is characterized. The purpose of a vibration energy harvester is to convert low grade vibrations to useful electrical power. Optimally, the natural frequency o...

  14. Long-range attractive forces extending from the alumina’s nanolayer surface in aqueous solutions

    Directory of Open Access Journals (Sweden)

    Leonid A. Kaledin

    2015-07-01

    Full Text Available Aluminum oxide-hydroxide nanolayer with a thickness of approximately 1.2 nm is electroadhesively deposited onto silicious support material with large surface area of about 50 m2/g, forming a highly electropositive composite of boehmite nanolayer in the form of monocrystalline oxide/hydroxide (α-Al2O3·H2O on the second electronegative solid. The composite can be viewed as a sphere with a rough surface and charge density of approximately 0.08 C/m2. This creates a significant electric field with negligible screening (ka ≪ 1 in the region close to the surface of the nanocomposite. This field attracts nano- and micron-sized particles from as far as 200 μm in a few seconds, many orders of magnitude greater than conventional Derjaguin–Landau–Verwey–Overbeek (DLVO theory, which predicts only nanometer-scale effects arising from the presence of the surface. The strong electric field on the surface is then able to retain small particles such as viruses, atomically thin sheets of graphene oxide, RNA, DNA, proteins, dyes as well as heavy metals such as cobalt, arsenic, and lead. Alumina’s nanolayer surface can be further functionalized by adding other sub-micron or nano-sized particles to target a specific contaminant. An example is shown where alumina nanolayer is coated with nano-sized iron monohydrate to yield an arsenic sorbent that shows high sorption capacity.

  15. Research Investigation Directed Toward Extending the Useful Range of the Electromagnetic Spectrum. Appendix.

    Science.gov (United States)

    1987-12-31

    contro’ s ide- wal IIProf ilIes du ring prcc ess. mg by u:: nd etchant gas/monomer em’ixtu res i r radiated with an excimer laser. In thelir initial wrk...Federico Capasso and Malvin C. Teich p 5-" .5 5 m w 4 %S N I , - Reprinted from PHYSICAL REVIEW LETTERS Vol. 57, No. 12, 22 September 1986 ’- ~~1417...Electron Feedback Federico Capasso A T& T Bell Laboratories. Murray Hill. Nem Jersev O 79 74 and Malvin C. Teich Columhbia Raiaution Laboratori

  16. EU-US evaluation of range extended electric vehicle performance at varying ambient temperatures

    OpenAIRE

    STUTENBERG KEVIN; GALASSI MARIA CRISTINA; OTURA GARCIA MARCOS; TRENTADUE GERMANA; SCHOLZ HARALD; CARRIERO MASSIMO; LOHSE-BUSCH H.

    2016-01-01

    The US DoE Argonne National Laboratory (ANL) and the EC Joint Research Centre (JRC) collaborate to promote a common EU/US approach towards global harmonization of standards for e-mobility and smart grids, with a common work plan including pre-normative research on the energy efficiency of electric vehicles (EVs). The aim of this paper is to introduce the cooperative and complementary ANL-JRC activities focusing on chassis dynamometer testing of electrified vehicles. Within this research progr...

  17. Evaluation of Fuel-Cell Range Extender Impact on Hybrid Electrical Vehicle Performance

    DEFF Research Database (Denmark)

    Jensen, Hans-Christian Becker; Schaltz, Erik; Koustrup, Per Sune

    2013-01-01

    of a vehicle with an internal combustion engine (ICE). Fuel cells (FCs) can be added to an EV as an additional energy source. These are faster to refill and will therefore facilitate the transition from vehicles running on fossil fuel to electricity. Different EV setups with FC strategies are presented...

  18. Research Investigation Directed Toward Extending the Useful Range of the Electromagnetic Spectrum.

    Science.gov (United States)

    1987-12-31

    Brennan, T. Wang, and K. Hess , IEEE Elec. Device Lett. 6, 199 (1985). 8 R. Ludeke, D. Straub, F. J. Himpsel and G. Landgren, J. Vac. Sci. Technol. A...800 North Qui~nc% Scrett Dr. Rudolf C. Buser galling Al. X :033: Am : Code .11I1A Night ’.Lsion & Electro-Optics Arrln tton. VA Dbs r. J. Neff ATT-N

  19. The investigation of spectrum shape of atmospheric inhomogeneities over an extended dynamic range

    Science.gov (United States)

    Kovadlo, P. G.; Shihovtsev, A. Y.; Kochetkova, O. S.

    2012-11-01

    Energy spectra of wind speed fluctuations and temperature fluctuations are calculated at altitudes between 2 and 301 m for the period from January 1, 2008 to 31 December, 2008 by using results of numerical analysis of high-altitude meteorological mast data. Comparison of the shape of the calculated spectra with known shapes has confirmed presence of two basic regions of wavenumbers with an approximate "-3" dependence and "-5/3" dependence. The result obtained has been used for estimating of high-frequency characteristics of atmospheric turbulence using network meteorological data.

  20. An Investigation of Soviet Capabilities in Extended Range Arctic Ice Forecasting.

    Science.gov (United States)

    1987-12-01

    changes in the thermohaline state of waters of the Faeroe-Shetland Channel. PAA, 49, 37-43. Zakharov, V. F., and L. A. Strokina, 1978: Recent variations in... discovered a connection between 3 extreme weather phenomena and periods of solar activity. This applies particularly to droughts: 22 * year and 11

  1. UAS Power amplifier for Extended range of Non-payload communication Devices (UPEND) Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The integration of Unmanned Aircraft Systems (UAS) into the National Airspace System (NAS) requires a robust, reliable communication link between the Unmanned Aerial...

  2. Research Investigation Directed Toward Extending the Useful Range of the Electromagnetic Spectrum.

    Science.gov (United States)

    1983-03-31

    acetonitrile (CH3CN) in Ar, has a simple LIF spectrum which can be probed by the fundamental of the BBQ dye at 387nm. This experiment will be done in...and triplet sensitization experiments to evaluate the rates of singlet-triplet interconversion of DPM in acetonitrile at ambient temperature. From these...have chosen to study the mixed solvent system butanol /hexadecane because of their similar viscosities 3.0 and 3.3 cp at 200C, respectively. The

  3. A novel optical membrane with extended detection range of pH

    OpenAIRE

    NOROOZIFAR, Meissam; MOTLAGH, Mozhgan KHORASANI; BAHMANZADEH, Safeyeh

    2014-01-01

    A pH optical sensor was developed based on the use of a mixture of Malachite Green Oxalate and Bromocresol Green indicators immobilized in a triacetylcellulose membrane, which had been previously hydrolyzed. Requirements of the pH indicators were investigated, including the effects of the coupling pH, indicator ratio, and concentrations of the indicators. The pH sensor performed with a very fast response (10 s) and long term stability with no significant leaching of the dyes. The se...

  4. Dating Techniques

    Indian Academy of Sciences (India)

    Absolute dating technique (such as stylistic affiliation, association with datable deposits, amino acid study of protein in pigments, and direct radiocarbon dating of the organic fraction of pigments or desert varnish).

  5. Intensity techniques

    DEFF Research Database (Denmark)

    Jacobsen, Finn

    2008-01-01

    The Handbook of Signal Processing in Acoustics will compile the techniques and applications of signal processing as they are used in the many varied areas of Acoustics. The Handbook will emphasize the interdisciplinary nature of signal processing in acoustics. Each Section of the Handbook...... from different areas, will find the self-contained chapters accessible and will be interested in the similarities and differences between the approaches and techniques used in different areas of acoustics....

  6. Extension of the Viscous Collision Limiting Direct Simulation Monte Carlo Technique to Multiple Species

    Science.gov (United States)

    Liechty, Derek S.; Burt, Jonathan M.

    2016-01-01

    There are many flows fields that span a wide range of length scales where regions of both rarefied and continuum flow exist and neither direct simulation Monte Carlo (DSMC) nor computational fluid dynamics (CFD) provide the appropriate solution everywhere. Recently, a new viscous collision limited (VCL) DSMC technique was proposed to incorporate effects of physical diffusion into collision limiter calculations to make the low Knudsen number regime normally limited to CFD more tractable for an all-particle technique. This original work had been derived for a single species gas. The current work extends the VCL-DSMC technique to gases with multiple species. Similar derivations were performed to equate numerical and physical transport coefficients. However, a more rigorous treatment of determining the mixture viscosity is applied. In the original work, consideration was given to internal energy non-equilibrium, and this is also extended in the current work to chemical non-equilibrium.

  7. antimicrobial susceptibility pattern of extended spectrum

    African Journals Online (AJOL)

    JAMILU

    ABSTRACT. The emergence of resistant strains of urogenital extended spectrum beta-lactamase producing ... antimicrobial susceptibility test using CLSI recommended, WHO modified Kirby Bauer disc diffusion method. ... Keywords: Extended Spectrum Beta-lactamases, Prevalence, Gram-negative urogenital isolates,.

  8. Quantum Potential and Symmetries in Extended Phase Space

    Directory of Open Access Journals (Sweden)

    Sadollah Nasiri

    2006-06-01

    Full Text Available The behavior of the quantum potential is studied for a particle in a linear and a harmonic potential by means of an extended phase space technique. This is done by obtaining an expression for the quantum potential in momentum space representation followed by the generalization of this concept to extended phase space. It is shown that there exists an extended canonical transformation that removes the expression for the quantum potential in the dynamical equation. The situation, mathematically, is similar to disappearance of the centrifugal potential in going from the spherical to the Cartesian coordinates that changes the physical potential to an effective one. The representation where the quantum potential disappears and the modified Hamilton-Jacobi equation reduces to the familiar classical form, is one in which the dynamical equation turns out to be the Wigner equation.

  9. Range Selection and Median

    DEFF Research Database (Denmark)

    Jørgensen, Allan Grønlund; Larsen, Kasper Green

    2011-01-01

    that supports queries in constant time, needs n1+ (1) space. For data structures that uses n logO(1) n space this matches the best known upper bound. Additionally, we present a linear space data structure that supports range selection queries in O(log k= log log n + log log n) time. Finally, we prove that any...

  10. Electric vehicles: Driving range

    Science.gov (United States)

    Kempton, Willett

    2016-09-01

    For uptake of electric vehicles to increase, consumers' driving-range needs must be fulfilled. Analysis of the driving patterns of personal vehicles in the US now shows that today's electric vehicles can meet all travel needs on almost 90% of days from a single overnight charge.

  11. Decomposition techniques

    Science.gov (United States)

    Chao, T.T.; Sanzolone, R.F.

    1992-01-01

    Sample decomposition is a fundamental and integral step in the procedure of geochemical analysis. It is often the limiting factor to sample throughput, especially with the recent application of the fast and modern multi-element measurement instrumentation. The complexity of geological materials makes it necessary to choose the sample decomposition technique that is compatible with the specific objective of the analysis. When selecting a decomposition technique, consideration should be given to the chemical and mineralogical characteristics of the sample, elements to be determined, precision and accuracy requirements, sample throughput, technical capability of personnel, and time constraints. This paper addresses these concerns and discusses the attributes and limitations of many techniques of sample decomposition along with examples of their application to geochemical analysis. The chemical properties of reagents as to their function as decomposition agents are also reviewed. The section on acid dissolution techniques addresses the various inorganic acids that are used individually or in combination in both open and closed systems. Fluxes used in sample fusion are discussed. The promising microwave-oven technology and the emerging field of automation are also examined. A section on applications highlights the use of decomposition techniques for the determination of Au, platinum group elements (PGEs), Hg, U, hydride-forming elements, rare earth elements (REEs), and multi-elements in geological materials. Partial dissolution techniques used for geochemical exploration which have been treated in detail elsewhere are not discussed here; nor are fire-assaying for noble metals and decomposition techniques for X-ray fluorescence or nuclear methods be discussed. ?? 1992.

  12. 42 CFR 488.310 - Extended survey.

    Science.gov (United States)

    2010-10-01

    ... 42 Public Health 5 2010-10-01 2010-10-01 false Extended survey. 488.310 Section 488.310 Public...) STANDARDS AND CERTIFICATION SURVEY, CERTIFICATION, AND ENFORCEMENT PROCEDURES Survey and Certification of Long-Term Care Facilities § 488.310 Extended survey. (a) Purpose of survey. The purpose of an extended...

  13. Extended empirical likelihood for estimating equations

    OpenAIRE

    Min Tsao; Fan Wu

    2014-01-01

    We derive an extended empirical likelihood for parameters defined by estimating equations which generalizes the original empirical likelihood to the full parameter space. Under mild conditions, the extended empirical likelihood has all the asymptotic properties of the original empirical likelihood. The first-order extended empirical likelihood is easy to use and substantially more accurate than the original empirical likelihood.

  14. A quantum extended Kalman filter

    Science.gov (United States)

    Emzir, Muhammad F.; Woolley, Matthew J.; Petersen, Ian R.

    2017-06-01

    In quantum physics, a stochastic master equation (SME) estimates the state (density operator) of a quantum system in the Schrödinger picture based on a record of measurements made on the system. In the Heisenberg picture, the SME is a quantum filter. For a linear quantum system subject to linear measurements and Gaussian noise, the dynamics may be described by quantum stochastic differential equations (QSDEs), also known as quantum Langevin equations, and the quantum filter reduces to a so-called quantum Kalman filter. In this article, we introduce a quantum extended Kalman filter (quantum EKF), which applies a commutative approximation and a time-varying linearization to systems of nonlinear QSDEs. We will show that there are conditions under which a filter similar to a classical EKF can be implemented for quantum systems. The boundedness of estimation errors and the filtering problem with ‘state-dependent’ covariances for process and measurement noises are also discussed. We demonstrate the effectiveness of the quantum EKF by applying it to systems that involve multiple modes, nonlinear Hamiltonians, and simultaneous jump-diffusive measurements.

  15. Extended attention span training system

    Science.gov (United States)

    Pope, Alan T.; Bogart, Edward H.

    1991-01-01

    Attention Deficit Disorder (ADD) is a behavioral disorder characterized by the inability to sustain attention long enough to perform activities such as schoolwork or organized play. Treatments for this disorder include medication and brainwave biofeedback training. Brainwave biofeedback training systems feed back information to the trainee showing him how well he is producing the brainwave pattern that indicates attention. The Extended Attention Span Training (EAST) system takes the concept a step further by making a video game more difficult as the player's brainwaves indicate that attention is waning. The trainee can succeed at the game only by maintaining an adequate level of attention. The EAST system is a modification of a biocybernetic system that is currently being used to assess the extent to which automated flight management systems maintain pilot engagement. This biocybernetic system is a product of a program aimed at developing methods to evaluate automated flight deck designs for compatibility with human capabilities. The EAST technology can make a contribution in the fields of medical neuropsychology and neurology, where the emphasis is on cautious, conservative treatment of youngsters with attention disorders.

  16. The motivation behind extended suicide

    Directory of Open Access Journals (Sweden)

    Roman Kuruc

    2014-12-01

    Full Text Available The investigation of motivation of suicidal behaviour in cases of so-called extended suicide is of great importance from a forensic-psychological viewpoint. The initiator of such action is often a person suffering from endogenous depression. The motives behind successful suicide are generally not known. This paper aims to demonstrate the motives behind the successful suicide, less frequent in our conditions, of two family members – a father and a son. The case has been thoroughly analysed by morphological methods with the help of additional laboratory tests. At the centre was a suicide letter which was hidden in a very unusual way and which was elucidated only thanks to autopsy of both persons. The manner of realisation – hanging – was among the most frequent in the region and in the state too. The men were not under the influence of any toxic substances. The motivation behind the suicide was an escape from hard living conditions.

  17. New range of heavy electric vehicle chassis

    Energy Technology Data Exchange (ETDEWEB)

    1979-06-01

    A new range of electrically-powered vehicles is announced in the UK. The vehicles are a joint venture between the Electric Vehicle Division of Hydrotechniek and its Dutch associate, Creusen Elektro-Mechanische Industrie BV. The 867S and 968S are three-axle vehicles with four-wheel drive on the rear four wheels. At present the vehicles go 20 km/h and have an 80-km range. The speed is to be extended in the near future and a diesel-electric hybrid may be introduced. An 867S is to be fitted out as a mobile library.

  18. Spermatological Parameters of Extended Rabbit Semen in 5 ...

    African Journals Online (AJOL)

    USER

    These problems range from nutritional challenges to availability of assisted reproductive techniques, most especially artificial insemination (AI) technique. Despite the use of AI in the large rabbit farms of several European countries, rabbit AI has certainly not become a common practice in the rabbit meat producing areas of.

  19. High Dynamic Range Video

    CERN Document Server

    Myszkowski, Karol

    2008-01-01

    This book presents a complete pipeline forHDR image and video processing fromacquisition, through compression and quality evaluation, to display. At the HDR image and video acquisition stage specialized HDR sensors or multi-exposure techniques suitable for traditional cameras are discussed. Then, we present a practical solution for pixel values calibration in terms of photometric or radiometric quantities, which are required in some technically oriented applications. Also, we cover the problem of efficient image and video compression and encoding either for storage or transmission purposes, in

  20. An Exploratory Analysis of Corrective Maintenance During Extended Surface Ship Deployments

    National Research Council Canada - National Science Library

    Werenskjold, G

    1998-01-01

    This thesis illustrates the use of simulation techniques to evaluate the corrective maintenance requirements, and resulting operational availability on-station, for a ship deployed for an extended period of three years...

  1. Miscellaneous Techniques

    Science.gov (United States)

    Jha, Shyam N.

    Nondestructive way of determining the food quality is the need of the hour. Till now major methods such as colour measurements and their modeling; machine vision systems; X-ray, CT and MRI; NIR spectroscopy; electronic nose and tongue; and ultrasonic technology have been discussed in detail. These techniques, in general, are considered to be sophisticated and costly, and therefore probably are not being adopted as fast as it should be. I am however of the reverse opinion. While going through these techniques, it has been seen that majority of quality parameters have been measured and correlated with the signals obtained using different equipment.

  2. Compact ranges in antenna and RCS measurements

    Science.gov (United States)

    Audone, B.

    1989-09-01

    With the increased complexity and extended frequency range of operation model measurements and far field test ranges are no longer suitable to satisfy the demand of accurate testing. Moreover plane wave test conditions are required for Radar Cross Section (RCS) measurements which represent a key point in stealth technology. Compact ranges represent the best test facilities available presently since they allow for indoor measurements under far field conditions in real time without any calculation effort. Several types of compact ranges are described and compared discussing their relevant advantages with regard to RCS and antenna measurements. In parallel to measuring systems sophisticated computer models were developed with such a high level of accuracy that it is questionable whether experiments give better results than theory. Tests performed on simple structures show the correlation between experimental results and theoretical ones derived on the basis of GTD computer codes.

  3. Worst-Case Efficient Range Searching

    DEFF Research Database (Denmark)

    Arge, Lars Allan

    2009-01-01

    In this tutorial we will describe some of the recent advances in the development of worst-case efficient range search indexing structures, that is, structures for storing a set of data points such that the points in a axis-parallel (hyper-) query rectangle can be found efficiently (with as few disk...... discuss the external priority search tree [8], which solves a restricted version of the two-dimensional version of the problem where the query rectangle is unbounded on one side. This structure is then used in a range tree index structure [8, 21] that answers general two-dimensional queries in the same......, 17], as well as recent index structures for higher-dimensional range search indexing [1]. We end by mentioning various R-tree variant [7, 18, 15] that can be used to solve the extended version of range search indexing where the queries as well as the data are (hyper-) rectangles. More comprehensive...

  4. Extending single-photon optimized superconducting transition edge sensors beyond the single-photon counting regime.

    Science.gov (United States)

    Gerrits, Thomas; Calkins, Brice; Tomlin, Nathan; Lita, Adriana E; Migdall, Alan; Mirin, Richard; Nam, Sae Woo

    2012-10-08

    Typically, transition edge sensors resolve photon number of up to 10 or 20 photons, depending on the wavelength and TES design. We extend that dynamic range up to 1000 photons, while maintaining sub-shot noise detection process uncertainty of the number of detected photons and beyond that show a monotonic response up to ≈ 6 · 10(6) photons in a single light pulse. This mode of operation, which heats the sensor far beyond its transition edge into the normal conductive regime, offers a technique for connecting single-photon-counting measurements to radiant-power measurements at picowatt levels. Connecting these two usually incompatible operating regimes in a single detector offers significant potential for directly tying photon counting measurements to conventional cryogenic radiometric standards. In addition, our measurements highlight the advantages of a photon-number state source over a coherent pulse source as a tool for characterizing such a detector.

  5. Extending the linear model with R generalized linear, mixed effects and nonparametric regression models

    CERN Document Server

    Faraway, Julian J

    2005-01-01

    Linear models are central to the practice of statistics and form the foundation of a vast range of statistical methodologies. Julian J. Faraway''s critically acclaimed Linear Models with R examined regression and analysis of variance, demonstrated the different methods available, and showed in which situations each one applies. Following in those footsteps, Extending the Linear Model with R surveys the techniques that grow from the regression model, presenting three extensions to that framework: generalized linear models (GLMs), mixed effect models, and nonparametric regression models. The author''s treatment is thoroughly modern and covers topics that include GLM diagnostics, generalized linear mixed models, trees, and even the use of neural networks in statistics. To demonstrate the interplay of theory and practice, throughout the book the author weaves the use of the R software environment to analyze the data of real examples, providing all of the R commands necessary to reproduce the analyses. All of the ...

  6. Land utilization and water resource inventories over extended test sites

    Science.gov (United States)

    Hoffer, R. M.

    1972-01-01

    In addition to the work on the corn blight this year, several other analysis tests were completed which resulted in significant findings. These aspects are discussed as follows: (1) field spectral measurements of soil conditions; (2) analysis of extended test site data; this discussion involves three different sets of data analysis sequences; (3) urban land use analysis, for studying water runoff potentials; and (4) thermal data quality study, as an expansion of our water resources studies involving temperature calibration techniques.

  7. Anisotropy signature in extended images from reverse-time migration

    KAUST Repository

    Sava, Paul

    2012-11-04

    Reverse-time migration can accurately image complex geologic structures in anisotropic media. Extended images at selected locations in the earth, i.e. at common-image-point gathers (CIPs), carry enough information to characterize the angle-dependent illumination and to provide measurements for migration velocity analysis. Furthermore, inaccurate anisotropy leaves a distinctive signature in CIPs, which can be used to evaluate anisotropy through techniques similar to the ones used in conventional wavefield tomography.

  8. From Sequential Extended Regular Expressions to NFA with Symbolic Labels

    Science.gov (United States)

    Cimatti, Alessandro; Mover, Sergio; Roveri, Marco; Tonetta, Stefano

    Practical property specification languages such as the IEEE standard PSL use at their core Sequential Extended Regular Expressions (SERE). In order to enable the reuse of traditional verification techniques, it is necessary to translate SEREs into automata. SERE are regular expressions built over alphabets resulting from the state variables of the design under analysis. Thus, a traditional approach to generate the automaton would suffer from the fact that the size of the alphabet is exponential in the number of symbols in the design.

  9. Analysis of RTM extended images for VTI media

    KAUST Repository

    Li, Vladimir

    2015-08-19

    Extended images obtained from reverse-time migration (RTM) contain information about the accuracy of the velocity field and subsurface illumination at different incidence angles. Here, we evaluate the influence of errors in the anisotropy parameters on the shape of the residual moveout (RMO) in P-wave RTM extended images for VTI (transversely isotropic with a vertical symmetry axis) media. Considering the actual spatial distribution of the zero-dip NMO velocity (Vnmo), which could be approximately estimated by conventional techniques, we analyze the extended images obtained with distorted fields of the parameters η and δ. Differential semblance optimization (DSO) and stack-power estimates are employed to study the sensitivity of focusing to the anisotropy parameters. The results show that the signature of η is dip-dependent, whereas errors in δ cause defocusing only if that parameter is laterally varying. Hence, earlier results regarding the influence of η and δ on reflection moveout and migration velocity analysis remain generally valid in the extended image space for complex media. The dependence of RMO on errors in the anisotropy parameters provides essential insights for anisotropic wavefield tomography using extended images.

  10. High Dynamic Range X-Ray Detector Pixel Architectures Utilizing Charge Removal

    Science.gov (United States)

    Weiss, Joel T.; Shanks, Katherine S.; Philipp, Hugh T.; Becker, Julian; Chamberlain, Darol; Purohit, Prafull; Tate, Mark W.; Gruner, Sol M.

    2017-04-01

    Several charge integrating CMOS pixel front ends utilizing charge removal techniques have been fabricated to extend dynamic range for X-ray diffraction applications at synchrotron sourcesand X-ray free electron lasers (XFELs). The pixels described herein build on the mixed mode pixel array detector (MM-PAD) framework, developed previously by our group to perform high dynamic range imaging. These new pixels boast several orders of magnitude improvement in maximum flux over the MM-PAD, which is capable of measuring a sustained flux in excess of 108 X-rays/pixel/s while maintaining sensitivity to smaller signals, down to single X-rays. To extend dynamic range, charge is removed from the integration node of the frontend amplifier without interrupting integration. The number of times this process occurs is recorded by a digital counter in the pixel. The parameter limiting full well is, thereby, shifted from the size of an integration capacitor to the depth of a digital counter. The result is similar to that achieved by counting pixel array detectors, but the integrators presented here are designed to tolerate a sustained flux > 1011 X-rays/pixel/s. Pixel front-end linearity was evaluated by direct current injection and results are presented. A small-scale readout ASIC utilizing these pixel architectures has been fabricated and the use of these architectures to increase single X-ray pulse dynamic range at XFELs is discussed briefly.

  11. Extending particle tracking capability with Delaunay triangulation.

    Science.gov (United States)

    Chen, Kejia; Anthony, Stephen M; Granick, Steve

    2014-04-29

    Particle tracking, the analysis of individual moving elements in time series of microscopic images, enables burgeoning new applications, but there is need to better resolve conformation and dynamics. Here we describe the advantages of Delaunay triangulation to extend the capabilities of particle tracking in three areas: (1) discriminating irregularly shaped objects, which allows one to track items other than point features; (2) combining time and space to better connect missing frames in trajectories; and (3) identifying shape backbone. To demonstrate the method, specific examples are given, involving analyzing the time-dependent molecular conformations of actin filaments and λ-DNA. The main limitation of this method, shared by all other clustering techniques, is the difficulty to separate objects when they are very close. This can be mitigated by inspecting locally to remove edges that are longer than their neighbors and also edges that link two objects, using methods described here, so that the combination of Delaunay triangulation with edge removal can be robustly applied to processing large data sets. As common software packages, both commercial and open source, can construct Delaunay triangulation on command, the methods described in this paper are both computationally efficient and easy to implement.

  12. Dynamic headspace time-extended helix liquid-phase microextraction.

    Science.gov (United States)

    Huang, Shih-Pin; Chen, Pai-Shan; Huang, Shang-Da

    2009-05-15

    Liquid-phase microextraction (LPME) has been proved to be a fast, inexpensive and effective sample pre-treatment technique for the analyses of pesticides and many other compounds. In this investigation, a new headspace microextraction technique, dynamic headspace time-extended helix liquid-phase microextraction (DHS-TEH-LPME), is presented. In this work, use of a solvent cooling system, permits the temperature of the extraction solvent to be lowered. Lowering the temperature of the extraction solvent not only reduces solvent loss but also extends the feasible extraction time, thereby improving extraction efficiency. Use of a larger volume of the solvent not only extends the feasible extraction time but also, after extraction, leaves a larger volume to be directly injected into the gas chromatography (GC) to increase extraction efficiency and instrument signal. The DHS-TEH-LPME technique was used to extract six organochlorine pesticides (OCPs) from 110ml water samples that had been spiked with the analytes at ng/l levels, and stirred for 60min. The proposed method attained enrichments up to 2121 fold. The effects of extraction solvent identity, sample agitation, extraction time, extraction temperature, and salt concentration on extraction performance were also investigated. The method detection limits (MDLs) varied from 0.2 to 25ng/l. The calibration curves were linear for at least 2 orders of magnitude with R(2)>==0.996. Relative recoveries in river water were more than 86%.

  13. The MST Radar Technique

    Science.gov (United States)

    Balsley, B. B.

    1985-01-01

    The past ten year have witnessed the development of a new radar technique to examine the structure and dynamics of the atmosphere between roughly 1 to 100 km on a continuous basis. The technique is known as the MST (for Mesosphere-Stratosphere-Troposphere) technique and is usable in all weather conditions, being unaffected by precipitation or cloud cover. MST radars make use of scattering from small scale structure in the atmospheric refractive index, with scales of the order of one-half the radar wavelength. Pertinent scale sizes for middle atmospheric studies typically range between a fraction of a meter and a few meters. The structure itself arises primarily from atmospheric turbulence. The technique is briefly described along with the meteorological parameters it measures.

  14. Multisensor Data Integration Techniques

    Science.gov (United States)

    Evans, D. L.; Blake, P. L.; Conel, J. E.; Lang, H. R.; Logan, T. L.; Mcguffie, B. A.; Paylor, E. D.; Singer, R. B.; Schenck, L. R.

    1985-01-01

    The availability of data from sensors operating in several different wavelength regions had led to the development of new techniques and strategies for both data management and image analysis. Work is ongoing to develop computer techniques for analysis of integrated data sets. These techniques include coregistration of multisensor images, rectification of radar images in areas of topographic relief to ensure pixel to pixel registration with planimetric data sets, calibration of data so that signatures can be applied to remote areas, normalization of data acquired with disparate sensors and determination of extended spectral signatures of surface units. In addition, software is being developed to analyze coregistrated digital terrain and image data so that automated stratigraphic and structural analyses can be performed. These software procedures include: strike and dip determination, terrain profile generation, stratigraphic column generation, stratigraphic thickness measurements, structural cross-section generation, and creation of 3-D block diagrams. These techniques were applied to coregistered LANDSAT 4 Thematic Mapper (TM), Thermal Infrared Multispectral Scanner (TIMS), and multipolarization synthetic aperture radar (SAR) data of the Wind River Basin in Wyoming.

  15. Object-Extended OLAP Querying

    DEFF Research Database (Denmark)

    Pedersen, Torben Bach; Gu, Junmin; Shoshani, Arie

    2009-01-01

    On-line analytical processing (OLAP) systems based on a dimensional view of data have found widespread use in business applications and are being used increasingly in non-standard applications. These systems provide good performance and ease-of-use. However, the complex structures and relationshi...... with performance measurements that show that the approach is a viable alternative to a physically integrated data warehouse.......On-line analytical processing (OLAP) systems based on a dimensional view of data have found widespread use in business applications and are being used increasingly in non-standard applications. These systems provide good performance and ease-of-use. However, the complex structures and relationships...... inherent in data in non-standard applications are not accommodated well by OLAP systems. In contrast, object database systems are built to handle such complexity, but do not support OLAP-type querying well. This paper presents the concepts and techniques underlying a flexible, "multi-model" federated...

  16. Long-range antigravity

    Energy Technology Data Exchange (ETDEWEB)

    Macrae, K.I.; Riegert, R.J. (Maryland Univ., College Park (USA). Center for Theoretical Physics)

    1984-10-01

    We consider a theory in which fermionic matter interacts via long-range scalar, vector and tensor fields. In order not to be in conflict with experiment, the scalar and vector couplings for a given fermion must be equal, as is natural in a dimensionally reduced model. Assuming that the Sun is not approximately neutral with respect to these new scalar-vector charges, and if the couplings saturate the experimental bounds, then their strength can be comparable to that of gravity. Scalar-vector fields of this strength can compensate for a solar quadrupole moment contribution to Mercury's anomalous perihelion precession.

  17. A Trial of Extending Hemodialysis Hours and Quality of Life.

    Science.gov (United States)

    Jardine, Meg J; Zuo, Li; Gray, Nicholas A; de Zoysa, Janak R; Chan, Christopher T; Gallagher, Martin P; Monaghan, Helen; Grieve, Stuart M; Puranik, Rajesh; Lin, Hongli; Eris, Josette M; Zhang, Ling; Xu, Jinsheng; Howard, Kirsten; Lo, Serigne; Cass, Alan; Perkovic, Vlado

    2017-06-01

    The relationship between increased hemodialysis hours and patient outcomes remains unclear. We randomized (1:1) 200 adult recipients of standard maintenance hemodialysis from in-center and home-based hemodialysis programs to extended weekly (≥24 hours) or standard (target 12-15 hours, maximum 18 hours) hemodialysis hours for 12 months. The primary outcome was change in quality of life from baseline assessed by the EuroQol 5 dimension instrument (3 level) (EQ-5D). Secondary outcomes included medication usage, clinical laboratory values, vascular access events, and change in left ventricular mass index. At 12 months, median weekly hemodialysis hours were 24.0 (interquartile range, 23.6-24.0) and 12.0 (interquartile range, 12.0-16.0) in the extended and standard groups, respectively. Change in EQ-5D score at study end did not differ between groups (mean difference, 0.04 [95% confidence interval, -0.03 to 0.11]; P=0.29). Extended hours were associated with lower phosphate and potassium levels and higher hemoglobin levels. Blood pressure (BP) did not differ between groups at study end. Extended hours were associated with fewer BP-lowering agents and phosphate-binding medications, but were not associated with erythropoietin dosing. In a substudy with 95 patients, we detected no difference between groups in left ventricular mass index (mean difference, -6.0 [95% confidence interval, -14.8 to 2.7] g/m2; P=0.18). Five deaths occurred in the extended group and two in the standard group (P=0.44); two participants in each group withdrew consent. Similar numbers of patients experienced vascular access events in the two groups. Thus, extending weekly hemodialysis hours did not alter overall EQ-5D quality of life score, but was associated with improvement in some laboratory parameters and reductions in medication burden. (Clinicaltrials.gov identifier: NCT00649298). Copyright © 2017 by the American Society of Nephrology.

  18. Potential of infrared spectroscopy in combination with extended canonical variate analysis for identifying different paper types

    Science.gov (United States)

    Riba, Jordi-Roger; Canals, Trini; Cantero, Rosa; Iturriaga, Hortensia

    2011-02-01

    The increasing use of secondary fiber in papermaking has led to the production of paper containing a wide range of contaminants. Wastepaper mills need to develop quality control methods for evaluating the incoming wastepaper stock as well as testing the specifications of the final product. The goal of this work is to present a fast and successful methodology for identifying different paper types. In this way, undesirable paper types can be refused, thus improving the runnability of the paper machine and the quality of the paper manufactured. In this work we examine various types of paper using information obtained by an appropriate chemometric treatment of infrared spectral data. For this purpose, we studied a large number of paper sheets of three different types (namely coated, offset and cast-coated) supplied by several paper manufacturers. We recorded Fourier transform infrared (FTIR) spectra with the aid of an attenuated total reflectance (ATR) module and near-infrared (NIR) reflectance spectra by means of fiber optics. Both techniques proved expeditious and required no sample pretreatment. The primary objective of this work was to develop a methodology for the accurate identification of samples of different paper types. For this purpose, we used the chemometric discrimination technique extended canonical variate analysis (ECVA) in combination with the k nearest neighbor (kNN) method to classify samples in the prediction set. Use of the NIR and FTIR techniques under these conditions allowed paper types to be identified with 100% success in prediction samples.

  19. Tracking and Data Relay Satellite (TDRS) Orbit Estimation Using an Extended Kalman Filter

    Science.gov (United States)

    Ward, Douglas T.; Dang, Ket D.; Slojkowski, Steve; Blizzard, Mike; Jenkins, Greg

    2007-01-01

    Alternatives to the Tracking and Data Relay Satellite (TDRS) orbit estimation procedure were studied to develop a technique that both produces more reliable results and is more amenable to automation than the prior procedure. The Earth Observing System (EOS) Terra mission has TDRS ephemeris prediction 3(sigma) requirements of 75 meters in position and 5.5 millimeters per second in velocity over a 1.5-day prediction span. Meeting these requirements sometimes required reruns of the prior orbit determination (OD) process, with manual editing of tracking data to get an acceptable solution. After a study of the available alternatives, the Flight Dynamics Facility (FDF) began using the Real-Time Orbit Determination (RTOD(Registered TradeMark)) Kalman filter program for operational support of TDRSs in February 2007. This extended Kalman filter (EKF) is used for daily support, including within hours after most thrusting, to estimate the spacecraft position, velocity, and solar radiation coefficient of reflectivity (C(sub R)). The tracking data used are from the Bilateration Ranging Transponder System (BRTS), selected TDRS System (TDRSS) User satellite tracking data, and Telemetry, Tracking, and Command (TT&C) data. Degraded filter results right after maneuvers and some momentum unloads provided incentive for a hybrid OD technique. The results of combining EKF strengths with the Goddard Trajectory Determination System (GTDS) Differential Correction (DC) program batch-least-squares solutions, as recommended in a 2005 paper on the chain-bias technique, are also presented.

  20. Engineering Biosensors with Dual Programmable Dynamic Ranges.

    Science.gov (United States)

    Wei, Benmei; Zhang, Juntao; Ou, Xiaowen; Lou, Xiaoding; Xia, Fan; Vallée-Bélisle, Alexis

    2018-01-10

    Although extensively used in all fields of chemistry, molecular recognition still suffers from a significant limitation: host-guest binding displays a fixed, hyperbolic dose-response curve, which limits its usefulness in many applications. Here we take advantage of the high programmability of DNA chemistry and propose a universal strategy to engineer biorecognition-based sensors with dual programmable dynamic ranges. Using DNA aptamers as our model recognition element and electrochemistry as our readout signal, we first designed a dual signaling "signal-on" and "signal-off" adenosine triphosphate (ATP) sensor composed of a ferrocene-labeled ATP aptamer in complex to a complementary, electrode-bound, methylene-blue labeled DNA. Using this simple "dimeric" sensor, we show that we can easily (1) tune the dynamic range of this dual-signaling sensor through base mutations on the electrode-bound DNA, (2) extend the dynamic range of this sensor by 2 orders of magnitude by using a combination of electrode-bound strands with varying affinity for the aptamers, (3) create an ultrasensitive dual signaling sensor by employing a sequestration strategy in which a nonsignaling, high affinity "depletant" DNA aptamer is added to the sensor surface, and (4) engineer a sensor that simultaneously provides extended and ultrasensitive readouts. These strategies, applicable to a wide range of biosensors and chemical systems, should broaden the application of molecular recognition in various fields of chemistry.

  1. Battery Electric Vehicle (BEV or Range Extended Electric Vehicle (REEV? —Deciding Between Different Alternative Drives Based on Measured Individual Operational Profiles Véhicule électrique à batteries (BEV ou véhicule électrique à prolongateur d’autonomie (REEV ? — Choisir entre différents entraînements alternatifs sur la base de profils opérationnels individuels mesurés

    Directory of Open Access Journals (Sweden)

    Marker S.

    2013-05-01

    Electric Vehicle — véhicule électrique à batteries et REEV (Range Extended Electric Vehicle — véhicule électrique à prolongateur d’autonomie et est caractérisée par une procédure en trois étapes : le comportement individuel au volant du client est évalué ; les cycles de conduite individualisés et les habitudes opérationnelles comprenant le kilométrage journalier sont déterminés ; en appliquant ces cycles individualisés, des modèles numériques de concepts de groupe motopropulseur alternatif sont réalisés afin de simuler la consommation d’énergie. L’étude révèle que le dimensionnement de la batterie constitue l’élément le plus important. Un véhicule REEV possédant une batterie plus petite serait plus efficace qu’un véhicule BEV : pour une autonomie donnée de 50 km, le véhicule BEV parcourt 50 % des kilomètres totaux (correspondant à 90 Vo de l’ensemble des distances journalières alors que le véhicule REEV parcourt 100 % de l’ensemble des distances journalières, dont 70 % en mode électrique. Ceci amène à une plus faible émission de CO2 par rapport à l’utilisation associée des véhicules BEV et des véhicules conventionnels. Le véhicule REEV possédant une batterie plus petite est amorti plus tôt qu’un véhicule conventionnel. L’influence exercée par le type d’usage individuel peut être traduite en coûts d’exploitation. Le conducteur urbain d’un véhicule REEV parcourt 85 % des trajets en mode électrique et bénéficie de coûts d’exploitation plus faibles que le conducteur interurbain d’un véhicule REEV parcourant 64 % des trajets en mode électrique.

  2. Electrochemical Techniques

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Gang; Lin, Yuehe

    2008-07-20

    Sensitive and selective detection techniques are of crucial importance for capillary electrophoresis (CE), microfluidic chips, and other microfluidic systems. Electrochemical detectors have attracted considerable interest for microfluidic systems with features that include high sensitivity, inherent miniaturization of both the detection and control instrumentation, low cost and power demands, and high compatibility with microfabrication technology. The commonly used electrochemical detectors can be classified into three general modes: conductimetry, potentiometry, and amperometry.

  3. Experimental Techniques

    DEFF Research Database (Denmark)

    Wyer, Jean

    2013-01-01

    Gas-phase ion spectroscopy requires specialised apparatus, both when it comes to measuring photon absorption and light emission (fluorescence). The reason is much lower ion densities compared to solution-phase spectroscopy. In this chapter different setups are described, all based on mass spectro...... in data interpretation, and the advantages and disadvantages of the different techniques are clarified. New instrumental developments involving cryo-cooled storage rings, which show great promise for the future, are briefly touched upon....

  4. Astrophysical techniques

    CERN Document Server

    Kitchin, CR

    2013-01-01

    DetectorsOptical DetectionRadio and Microwave DetectionX-Ray and Gamma-Ray DetectionCosmic Ray DetectorsNeutrino DetectorsGravitational Radiation Dark Matter and Dark Energy Detection ImagingThe Inverse ProblemPhotographyElectronic ImagingScanningInterferometrySpeckle InterferometryOccultationsRadarElectronic ImagesPhotometryPhotometryPhotometersSpectroscopySpectroscopy SpectroscopesOther TechniquesAstrometryPolarimetrySolar StudiesMagnetometryComputers and The Internet.

  5. Systematic application of DNA fiber-FISH technique in cotton.

    Directory of Open Access Journals (Sweden)

    Kai Wang

    Full Text Available Fluorescence in situ hybridization on extended DNA (fiber-FISH is a powerful tool in high-resolution physical mapping. To introduce this technique into cotton, we developed the technique and tested it by deliberately mapping of telomere and 5S rDNA. Results showed that telomere-length ranged from 0.80 kb to 37.86 kb in three species, G. hirsutum, G. herbaceum and G. arboreum. However, most of the telomeres (>91.0% were below 10 kb. The length of 5S rDNA was revealed as 964 kb in G. herbaceum whereas, in G. arboreum, it was approximately three times longer (3.1 Mb. A fiber-FISH based immunofluorescence method was also described to assay the DNA methylation. Using this technique, we revealed that both telomere and 5S rDNA were methylated at different levels. In addition, we developed a BAC molecule-based fiber-FISH technique. Using this technique, we can precisely map BAC clones on each other and evaluated the size and location of overlapped regions. The development and application of fiber-FISH technique will facilitate high-resolution physical mapping and further directed sequencing projects for cotton.

  6. Tilt anisoplanatism in extended turbulence propagation

    Science.gov (United States)

    Magee, Eric P.; Whiteley, Matthew R.; Das, Shashikala T.; Welsh, Byron M.

    2003-04-01

    The use of high-energy laser (HEL) weapon systems in tactical air-to-ground target engagements offers great promise for revolutionizing the USAF's war-fighting capabilities. Laser directed-energy systems will enable ultra-precision strike with minimal collateral damage and significant stand-off range for the aerial platform. The tactical directed energy application differs in many crucial ways from the conventional approach used in missile defense. Tactical missions occur at much lower altitudes and involve look-down to low-contrast ground targets instead of a high-contrast boosting missile. At these lower altitudes, the strength of atmospheric turbulence is greatly enhanced. Although the target slant ranges are much shorter, tactical missions may still involve moderate values of the Rytov number (0.1-0.5), and small isoplanatic angles compared to the diffraction angle. With increased density of air in the propagation path, and the potential for slow-moving or stationary ground targets, HEL-induced thermal blooming will certainly be a concern. In order to minimize the errors induced by tracking through thermal blooming, offset aimpoint tracking can be used. However, this will result in significant tilt anisoplanatism, thus degrading beam stabilization on target. In this paper we investigate the effects of extended turbulence on tracking (or tilt) anisoplanatism using theory and wave optics simulations. The simulations show good agreement with geometric optics predictions at angles larger than about 5 micro-radians (asymptotic regime) while at smaller angles the agreement is poor. We present a theoretical basis for this observation.

  7. Lightning detection and ranging

    Science.gov (United States)

    Lennon, C. L.; Poehler, H. A.

    1982-01-01

    A lightning detector and ranging (LDAR) system developed at the Kennedy Space Center and recently transferred to Wallops Island is described. The system detects pulsed VHF signals due to electrical discharges occurring in a thunderstorm by means of 56-75 MHz receivers located at the hub and at the tips of 8 km radial lines. Incoming signals are transmitted by wideband links to a central computing facility which processes the times of arrival, using two independent calculations to determine position in order to guard against false data. The results are plotted on a CRT display, and an example of a thunderstorm lightning strike detection near Kennedy Space Center is outlined. The LDAR correctly identified potential ground strike zones and additionally provided a high correlation between updrafts and ground strikes.

  8. USE OF DIFFERENT EXTENDERS TO CRYOPRESERVATION OF MANGALARGA MARCHADOR SPERM

    Directory of Open Access Journals (Sweden)

    Jessica Neri Nascimento

    2015-07-01

    Full Text Available The techniques applied to animal reproduction such as artificial insemination, transfer and in vitro production of embryos, heat synchronization and induction, and gametes cryopreservation have been more utilized in veterinary practice each day. Nevertheless, some techniques have not achieved their full technical capacity within the equine reproduction field, such as semen cryopreservation. The aim of this study was to evaluate the characteristics of post-thawing semen (total motility, strength, plasmatic and acrosomal membrane integrity of Mangalarga Marchador breed stallions, using three different extenders (Botucrio, FR5 and FR6. Ejaculates from five stallions were collected and the gel-free semen was diluted in a 1:1 dilution in skim milk extender, and centrifuged at 600 g for 10 minutes. After the centrifugation the supernatant was removed and sperm pellet was divided and re-suspended using three different extenders to a concentration of 200 x 106 cells/mL. The samples were packed into 0.5 mL straws, placed in a stainless steel support and kept inside the refrigerator (5 oC for one hour. Subsequently, these straws were kept at a height of 6 cm from liquid nitrogen for 15 minutes in an isotherm box and, after that, plunged into liquid nitrogen (-196 oC and stored in a liquid nitrogen holding tank. There were no differences in the parameters evaluated when extenders using mixed amides and glycerol (Botucrio and FR6 were used (P > 0.05. All parameters evaluated were lower for the extender containing only glycerol (P<0.05. The use of cryoprotectants (methylformamide and dimethylformamide in association with glycerol concentrations around 1 to 2% is an alternative for semen cryopreservation of Mangalarga Marchador breed stallions.

  9. Thermalization and Pseudolocality in Extended Quantum Systems

    Science.gov (United States)

    Doyon, Benjamin

    2017-04-01

    Recently, it was understood that modified concepts of locality played an important role in the study of extended quantum systems out of equilibrium, in particular in so-called generalized Gibbs ensembles. In this paper, we rigorously study pseudolocal charges and their involvement in time evolutions and in the thermalization process of arbitrary states with strong enough clustering properties. We show that the densities of pseudolocal charges form a Hilbert space, with inner product determined by thermodynamic susceptibilities. Using this, we define the family of pseudolocal states, which are determined by pseudolocal charges. This family includes thermal Gibbs states at high enough temperatures, as well as (a precise definition of) generalized Gibbs ensembles. We prove that the family of pseudolocal states is preserved by finite time evolution, and that, under certain conditions, the stationary state emerging at infinite time is a generalized Gibbs ensemble with respect to the evolution dynamics. If the evolution dynamics does not admit any conserved pseudolocal charges other than the evolution Hamiltonian, we show that any stationary pseudolocal state with respect to these dynamics is a thermal Gibbs state, and that Gibbs thermalization occurs. The framework is that of translation-invariant states on hypercubic quantum lattices of any dimensionality (including quantum chains) and finite-range Hamiltonians, and does not involve integrability.

  10. In-Vivo High Dynamic Range Vector Flow Imaging

    DEFF Research Database (Denmark)

    Villagómez Hoyos, Carlos Armando; Stuart, Matthias Bo; Jensen, Jørgen Arendt

    2015-01-01

    Current vector flow systems are limited in their detectable range of blood flow velocities. Previous work on phantoms has shown that the velocity range can be extended using synthetic aperture directional beamforming combined with an adaptive multi-lag approach. This paper presents a first invivo...

  11. Extended empirical likelihood for general estimating equations

    OpenAIRE

    Tsao, Min; Wu, Fan

    2013-01-01

    We derive an extended empirical likelihood for parameters defined by estimating equations which generalizes the original empirical likelihood for such parameters to the full parameter space. Under mild conditions, the extended empirical likelihood has all asymptotic properties of the original empirical likelihood. Its contours retain the data-driven shape of the latter. It can also attain the second order accuracy. The first order extended empirical likelihood is easy-to-use yet it is substan...

  12. Terahertz Techniques

    CERN Document Server

    Bründermann, Erik; Kimmitt, Maurice FitzGerald

    2012-01-01

    Research and development in the terahertz portion of the electromagnetic spectrum has expanded very rapidly during the past fifteen years due to major advances in sources, detectors and instrumentation. Many scientists and engineers are entering the field and this volume offers a comprehensive and integrated treatment of all aspects of terahertz technology. The three authors, who have been active researchers in this region over a number of years, have designed Terahertz Techniques to be both a general introduction to the subject and a definitive reference resource for all those involved in this exciting research area.

  13. Elderly diabetic patient with surgical site mucormycosis extending to bowel

    Directory of Open Access Journals (Sweden)

    Atul K Patel

    2010-01-01

    Full Text Available Mucormycosis is rare in clinical practice. Most infections are acquired by inhalation; other portals of entry are traumatic implantation and ingestion in immunocompromised host. Mucormycosis is life threatening infection in immunocompromised host with variable moratlity ranging from 15 -81% depending upon site of infection. General treatment principles include early diagnosis, correction of underlying immunosuppression and metabolic disturbances, adequate surgical debridement along with amphotericin therapy. We describe surgical site mucormycosis extended to involve large bowel in elderly diabetic patient.

  14. Endoscopic navigation system with extended field of view using augmented reality technology.

    Science.gov (United States)

    Bong, Jae Hwan; Song, Hyun-Jong; Oh, Yoojin; Park, Namji; Kim, Hyungmin; Park, Shinsuk

    2017-12-28

    While endoscopic skull base surgery (ESBS) has emerged as an alternative surgical option, the limited field of view of the endoscope may lead to the surgeon's fatigue and discomfort. The developed navigation system includes extended augmented reality (AR), which can provide an extended viewport to a conventional endoscopic view by overlaying 3D anatomical models generated from preoperative medical images onto endoscope images. To enhance the accuracy of the developed system, we adopted state-of-the-art endoscopic calibration and tracking techniques based on an optical tracking system. The mean spatial errors of AR was ~1 mm, which falls in the acceptable range of accuracy for ESBS. For the simulated surgical tasks with the developed system, the number and duration of error events were decreased. The results show that the human subject can perform the task more precisely and safely with the developed AR-based navigation system than with the conventional endoscopic system. Copyright © 2017 John Wiley & Sons, Ltd.

  15. Expert systems and ballistic range data analysis

    Science.gov (United States)

    Hathaway, Wayne; Steinhoff, Mark; Whyte, Robert; Brown, David; Choate, Jeff; Adelgren, Russ

    1992-07-01

    A program aimed at the development of an expert system for the reduction of ballistic range data is described. The program applies expert system and artificial intelligence techniques to develop a mathematically complex state-of-the-art spark range data reduction procedure that includes linear theory and six-degree-of-freedom analysis. The scope of the knowledge base includes both spin and statically stable vehicles. The expert system is expected to improve the quality of the data reduction process while reducing the work load on the senior range engineer.

  16. Empirical techniques in finance

    CERN Document Server

    Bhar, Ramaprasad

    2005-01-01

    This book offers the opportunity to study and experience advanced empi- cal techniques in finance and in general financial economics. It is not only suitable for students with an interest in the field, it is also highly rec- mended for academic researchers as well as the researchers in the industry. The book focuses on the contemporary empirical techniques used in the analysis of financial markets and how these are implemented using actual market data. With an emphasis on Implementation, this book helps foc- ing on strategies for rigorously combing finance theory and modeling technology to extend extant considerations in the literature. The main aim of this book is to equip the readers with an array of tools and techniques that will allow them to explore financial market problems with a fresh perspective. In this sense it is not another volume in eco- metrics. Of course, the traditional econometric methods are still valid and important; the contents of this book will bring in other related modeling topics tha...

  17. Propeller Flaps: A Review of Indications, Technique, and Results

    Directory of Open Access Journals (Sweden)

    Salvatore D'Arpa

    2014-01-01

    Full Text Available In the last years, propeller flaps have become an appealing option for coverage of a large range of defects. Besides having a more reliable vascular pedicle than traditional flap, propeller flaps allow for great freedom in design and for wide mobilization that extend the possibility of reconstructing difficult wounds with local tissues and minimal donor-site morbidity. They also allow one-stage reconstruction of defects that usually require multiple procedures. Harvesting of a propeller flap requires accurate patient selection, preoperative planning, and dissection technique. Complication rate can be kept low, provided that potential problems are prevented, promptly recognized, and adequately treated. This paper reviews current knowledge on propeller flaps. Definition, classification, and indications in the different body regions are discussed based on a review of the literature and on the authors’ experience. Details about surgical technique are provided, together with tips to avoid and manage complications.

  18. Lidar techniques for environmental and ecological monitoring

    Science.gov (United States)

    Svanberg, Sune

    2015-04-01

    An overview of optical probing of the atmosphere will be given, where mostly active remote- sensing techniques of the laser-radar type will be covered, but also some passive techniques employing ambient radiation. Atmospheric objects of quite varying sizes can be studied. Mercury is the only pollutant in atomic form in the atmosphere, while other pollutants are either molecular or in particle form. Light detection and ranging (Lidar) techniques allow three-dimensional mapping of such constituents, and examples from atmospheric lidar work in Lund and in Guangzhou will be given. Recently, much larger lidar targets have been studied. Monitoring of flying insects and birds is of considerable ecological interest, and several projects have been pursued in collaboration with biologists. Mostly, elastic backscattering and fluorescence techniques are employed. Some references to recent activities by the author and his colleagues are given below. [1] Z.G. Guan, L. Mei, P. Lundin, G. Somesfalean, and S. Svanberg, Vertical Lidar Sounding of Air Pollutants in a Major Chinese City, Appl. Phys. B 101, 465 (2010) [2] L. Mei, G.Y. Zhou and S. Svanberg, Differential Absorption Lidar System Employed for Background Atomic Mercury Vertical Profiling in South China, Lasers Opt. Eng. 55, 128 (2013) [3] Z.G. Guan, M. Brydegaard, P. Lundin, M. Wellenreuther, E. Svensson, and S. Svanberg, Insect Monitoring with Fluorescence LIDAR techniques - Field experiments, Appl. Optics 48, 5668 (2010) [4] A. Runemark, M. Wellereuther, H. Jayaweera, S. Svanberg and M. Brydegaard, Rare Events in Remote Dark Field Spectroscopy: An Ecological Case study of Insects, IEEE JSTQE 18, 1573 (2011) [5] L. Mei, Z.G. Guan, H.J. Zhou, J. Lv, Z.R. Zhu, J.A. Cheng, F.J. Chen, C. Löfstedt, S. Svanberg, and G. Somesfalean, Agricultural Pest Monitoring using Fluorescence Lidar Techniques, Applied Physics B 106, 733 (2011) [6] P. Lundin, P. Samuelsson, S. Svanberg, A. Runemark, S. Åkesson, and M. Brydegaard, Remote

  19. Fizeau simultaneous phase-shifting interferometry based on extended source

    Science.gov (United States)

    Wang, Shanshan; Zhu, Qiudong; Hou, Yinlong; Cao, Zheng

    2016-09-01

    Coaxial Fizeau simultaneous phase-shifting interferometer plays an important role in many fields for its characteristics of long optical path, miniaturization, and elimination of reference surface high-frequency error. Based on the matching of coherence between extended source and interferometer, orthogonal polarization reference wave and measurement wave can be obtained by Fizeau interferometry with Michelson interferometer preposed. Through matching spatial coherence length between preposed interferometer and primary interferometer, high contrast interference fringes can be obtained and additional interference fringes can be eliminated. Thus, the problem of separation of measurement and reference surface in the common optical path Fizeau interferometer is solved. Numerical simulation and principle experiment is conducted to verify the feasibility of extended source interferometer. Simulation platform is established by using the communication technique of DDE (dynamic data exchange) to connect Zemax and Matlab. The modeling of the extended source interferometer is realized by using Zemax. Matlab codes are programmed to automatically rectify the field parameters of the optical system and conveniently calculate the visibility of interference fringes. Combined with the simulation, the experimental platform of the extended source interferometer is established. After experimental research on the influence law of scattering screen granularity to interference fringes, the granularity of scattering screen is determined. Based on the simulation platform and experimental platform, the impacts on phase measurement accuracy of the imaging system aberration and collimation system aberration of the interferometer are analyzed. Compared the visibility relation curves between experimental measurement and simulation result, the experimental result is in line with the theoretical result.

  20. Anisotropy signature in reverse-time migration extended images

    KAUST Repository

    Sava, Paul C.

    2014-11-04

    Reverse-time migration can accurately image complex geologic structures in anisotropic media. Extended images at selected locations in the Earth, i.e., at common-image-point gathers, carry rich information to characterize the angle-dependent illumination and to provide measurements for migration velocity analysis. However, characterizing the anisotropy influence on such extended images is a challenge. Extended common-image-point gathers are cheap to evaluate since they sample the image at sparse locations indicated by the presence of strong reflectors. Such gathers are also sensitive to velocity error that manifests itself through moveout as a function of space and time lags. Furthermore, inaccurate anisotropy leaves a distinctive signature in common-image-point gathers, which can be used to evaluate anisotropy through techniques similar to the ones used in conventional wavefield tomography. It specifically admits a V-shaped residual moveout with the slope of the "V" flanks depending on the anisotropic parameter η regardless of the complexity of the velocity model. It reflects the fourth-order nature of the anisotropy influence on moveout as it manifests itself in this distinct signature in extended images after handling the velocity properly in the imaging process. Synthetic and real data observations support this assertion.