WorldWideScience

Sample records for exploiting flow injection

  1. Exploiting flow Injection and sequential injection schemes for trace metal determinations by electrothermal atomic absorption spectrometry

    DEFF Research Database (Denmark)

    Hansen, Elo Harald

    /SI-systems incorporating ion-exchange column reactors. Although extensively used, such devices suffer from some inherent drawbacks. Thus, because many ion-exchange resins undergo volume change when they are converted from the acid to the basic form, long-term use might lead to progressively tighter packing and hence...... increased flow resistance. This can, however, to a large extent be alleviated by using countercurrent flow. Besides, the surface properties of the resin might be irreversibly changed after having been subjected to a large number of samples, either due to contamination, deactivation, or even loss of its...... functional groups. These problems are especially serious when using ETAAS as the detection device, because the limited accommodation volume of the graphite tube requires that the retained analyte must be eluted completely – or at least to a reproducible degree - within a very small volume of eluent. All...

  2. New Trends in Flow Injection Analysis: Exploitation of Sequential and Lab-on-Valve Schemes

    DEFF Research Database (Denmark)

    Hansen, Elo Harald

    which are difficult or, in fact, otherwise impossible to do, thereby opening new and novel avenues for analytical methods relying on concepts such as kinetic discriminations schemes, exploitation of metastable constituents of attractive analytical characteristics, or utilisation of detection by bio...... sensitivity and selectivity. Either in order to separate/preconcentrate the analyte material, or because of the presence of potentially interfering matrix constituents. Such pretreatments are advantageously performed in FIA/SIA/LOV manifolds, where all appropriate unit operations can be effected under...

  3. Sequential injections as an alternative to gradient exploitation for implementing differential kinetic analysis in a flow injection system.

    Science.gov (United States)

    Fortes, Paula R; Feres, Mario A; Zagatto, Elias A G; Lima, José L F C

    2010-06-15

    A novel flow-based strategy for implementing simultaneous determinations of different chemical species reacting with the same reagent(s) at different rates is proposed and applied to the spectrophotometric catalytic determination of iron and vanadium in Fe-V alloys. The method relies on the influence of Fe(II) and V(IV) on the rate of the iodide oxidation by Cr(VI) under acidic conditions; the Jones reducing agent is then needed. Three different plugs of the sample are sequentially inserted into an acidic KI reagent carrier stream, and a confluent Cr(VI) solution is added downstream. Overlap between the inserted plugs leads to a complex sample zone with several regions of maximal and minimal absorbance values. Measurements performed on these regions reveal the different degrees of reaction development and tend to be more precise. Data are treated by multivariate calibration involving the PLS algorithm. The proposed system is very simple and rugged. Two latent variables carried out ca 95% of the analytical information and the results are in agreement with ICP-OES.

  4. Flow Injection Analysis

    DEFF Research Database (Denmark)

    Hansen, Elo Harald

    2004-01-01

    This chapter provides an introduction to automated chemical analysis, which essentially can be divided into two groups: batch assays, where the solution is stationary while the container is moved through a number of stations where various unit operations performed; and continuous-flow procedures......, where the system is stationary while the solution moves through a set of conduits in which all required manipulations are performed. Emphasis is placed on flow injection analysis (FIA) and its further developments, that is, sequential injection analysis (SIA) and the Lab-on-Valve (LOV) approach. Since...... FIA is based on the creation of a concentration gradient of the injected sample solution and on reproducible and precise timing of all events, it allows exploitation of a transient read-out. This in turn implies that not only does FIA allow the augmentation of existing analytical techniques...

  5. Exploiting flow injection and sequential injection for trace metal determinations in conjunction with detection by electrothermal atomic absorption spectrometry and inductively coupled plasma mass spectrometry

    DEFF Research Database (Denmark)

    Hansen, Elo Harald

    Despite their excellent analytical chemical capacities, Electrothermal Atomic Absorption Spectrometry (ETAAS) and Inductively Coupled Plasma Mass Spectrometry (ICPMS), nevertheless, often require suitable pretreatment of the sample material in order to obtain the necessary sensitivity...... and selectivity. Either in order to separate/preconcentrate the analyte material, or because of the presence of potentially interfering matrix constituents. Such pretreatments are advantageously performed in flow injection (FI) or sequential injection (SI) manifolds, where all appropriate unit operations can......, such as liquid-liquid extraction, (co)precipitation with collection in knotted reactors, adsorption, hydride generation, or the use of ion-exchange columns. Apart from hydride generation, where the analyte is converted into a gaseous species, the common denominator for these approaches is that the analyte...

  6. On-line dynamic fractionation and automatic determination of inorganic phosphorus in environmental solid substrates exploiting sequential injection microcolumn extraction and flow injection analysis

    Energy Technology Data Exchange (ETDEWEB)

    Buanuam, Janya [Department of Chemistry, Faculty of Science, Mahidol University, Rama VI Road, Bangkok 10400 (Thailand); Miro, Manuel [Department of Chemistry, Faculty of Sciences, University of the Balearic Islands, Carretera de Valldemossa km. 7.5, E-07122 Palma de Mallorca, Illes Balears (Spain)]. E-mail: manuel.miro@uib.es; Hansen, Elo Harald [Department of Chemistry, Technical University of Denmark, Kemitorvet, Building 207, DK-2800 Kgs. Lyngby (Denmark)]. E-mail: ehh@kemi.dtu.dk; Shiowatana, Juwadee [Department of Chemistry, Faculty of Science, Mahidol University, Rama VI Road, Bangkok 10400 (Thailand)

    2006-06-16

    Sequential injection microcolumn extraction (SI-MCE) based on the implementation of a soil-containing microcartridge as external reactor in a sequential injection network is, for the first time, proposed for dynamic fractionation of macronutrients in environmental solids, as exemplified by the partitioning of inorganic phosphorus in agricultural soils. The on-line fractionation method capitalises on the accurate metering and sequential exposure of the various extractants to the solid sample by application of programmable flow as precisely coordinated by a syringe pump. Three different soil phase associations for phosphorus, that is, exchangeable, Al- and Fe-bound, and Ca-bound fractions, were elucidated by accommodation in the flow manifold of the three steps of the Hieltjes-Lijklema (HL) scheme involving the use of 1.0 M NH{sub 4}Cl, 0.1 M NaOH and 0.5 M HCl, respectively, as sequential leaching reagents. The precise timing and versatility of SI for tailoring various operational extraction modes were utilized for investigating the extractability and the extent of phosphorus re-distribution for variable partitioning times. Automatic spectrophotometric determination of soluble reactive phosphorus in soil extracts was performed by a flow injection (FI) analyser based on the Molybdenum Blue (MB) chemistry. The 3{sigma} detection limit was 0.02 mg P L{sup -1} while the linear dynamic range extended up to 20 mg P L{sup -1} regardless of the extracting media. Despite the variable chemical composition of the HL extracts, a single FI set-up was assembled with no need for either manifold re-configuration or modification of chemical composition of reagents. The mobilization of trace elements, such as Cd, often present in grazed pastures as a result of the application of phosphate fertilizers, was also explored in the HL fractions by electrothermal atomic absorption spectrometry.

  7. On-line dynamic fractionation and automatic determination of inorganic phosphorus in environmental solid substrates exploiting sequential injection microcolumn extraction and flow injection analysis.

    Science.gov (United States)

    Buanuam, Janya; Miró, Manuel; Hansen, Elo Harald; Shiowatana, Juwadee

    2006-06-16

    Sequential injection microcolumn extraction (SI-MCE) based on the implementation of a soil-containing microcartridge as external reactor in a sequential injection network is, for the first time, proposed for dynamic fractionation of macronutrients in environmental solids, as exemplified by the partitioning of inorganic phosphorus in agricultural soils. The on-line fractionation method capitalises on the accurate metering and sequential exposure of the various extractants to the solid sample by application of programmable flow as precisely coordinated by a syringe pump. Three different soil phase associations for phosphorus, that is, exchangeable, Al- and Fe-bound, and Ca-bound fractions, were elucidated by accommodation in the flow manifold of the three steps of the Hieltjes-Lijklema (HL) scheme involving the use of 1.0M NH4Cl, 0.1M NaOH and 0.5M HCl, respectively, as sequential leaching reagents. The precise timing and versatility of SI for tailoring various operational extraction modes were utilized for investigating the extractability and the extent of phosphorus re-distribution for variable partitioning times. Automatic spectrophotometric determination of soluble reactive phosphorus in soil extracts was performed by a flow injection (FI) analyser based on the Molybdenum Blue (MB) chemistry. The 3sigma detection limit was 0.02 mg P L(-1) while the linear dynamic range extended up to 20 mg P L(-1) regardless of the extracting media. Despite the variable chemical composition of the HL extracts, a single FI set-up was assembled with no need for either manifold re-configuration or modification of chemical composition of reagents. The mobilization of trace elements, such as Cd, often present in grazed pastures as a result of the application of phosphate fertilizers, was also explored in the HL fractions by electrothermal atomic absorption spectrometry.

  8. On-line dynamic fractionation and automatic determination of inorganic phosphorous in environmental solid substrates exploiting sequential injection microcolumn extraction and flow injection analysi

    DEFF Research Database (Denmark)

    Buanuam, Janya; Miró, Manuel; Hansen, Elo Harald

    2006-01-01

    associations for phosphorus, that is, exchangeable, Al- and Fe-bound and Ca-bound fractions, were elucidated by accommodation in the flow manifold of the 3 steps of the Hietjles-Litjkema (HL) scheme involving the use of 1.0 M NH4Cl, 0.1 M NaOH and 0.5 M HCl, respectively, as sequential leaching reagents...

  9. Flow Injection Analysis

    DEFF Research Database (Denmark)

    Hansen, Elo Harald

    1998-01-01

    Learning objectives:* To provide an introduction to automated assays* To describe the basic principles of FIA * To demonstrate the capabilities of FIA in relation to batch assays and conventional continuous flow systems* To show that FIA allows one to augment existing analytical techniques* To show...

  10. Flow injection microbial trichloroethylene sensor.

    Science.gov (United States)

    Han, Tae-Sung; Sasaki, Satoshi; Yano, Kazuyoshi; Ikebukuro, Kazunori; Kitayama, Atsushi; Nagamune, Teruyuki; Karube, Isao

    2002-05-16

    A flow type microbial biosensor for direct measurement of trichloroethylene (TCE) was developed. The unique features of this novel microbial sensor were the use of the TCE degrading bacterium Pseudomonas aeruginosa JI104, the electrical detection of the chloride ion released by microbial degradation, and flow cell made of glass. Glass cell was used in order to suppress adsorption of TCE and made a closed reaction cell. Vaporization of TCE during the measurement was prevented using closed flow cell. The performance of the sensor was evaluated from following aspects; such as pH of the carrier solution, amount of the immobilized microbe, flow rate and injection volume. The sensor signals were linearly proportional to the concentration of TCE in the range from 0.03 to 2 mgl(-1), which is suitable for the determination of suspected samples to be drinkable water or not. The sensor performance was checked on the real sample, and this system showed good response in ground water, indicating its applicability for the on line monitoring at TCE contaminated areas or hazardous sites.

  11. The Three Generations of Flow Injection Analysis

    DEFF Research Database (Denmark)

    Hansen, Elo Harald; Wang, Jianhua

    2004-01-01

    The characteristics of the three generations of flow injection analysis, that is, FIA, sequential injection analysis (SIA), and bead injection-lab-on-valve (BI-LOV), are briefly outlined, their individual advantages and shortcomings are discussed, and selected practical applications are presented....

  12. Evaluation of the impact of viscosity, injection volume, and injection flow rate on subcutaneous injection tolerance

    Directory of Open Access Journals (Sweden)

    Berteau C

    2015-11-01

    Full Text Available Cecile Berteau,1 Orchidée Filipe-Santos,1 Tao Wang,2 Humberto E Rojas,2 Corinne Granger,1 Florence Schwarzenbach1 1Becton-Dickinson Medical Pharmaceutical Systems, Le Pont de Claix, France; 2Eli Lilly and Company, Indianapolis, IN, USA Aim: The primary objective of this study was to evaluate the impact of fluid injection viscosity in combination with different injection volumes and flow rates on subcutaneous (SC injection pain tolerance. Methods: The study was a single-center, comparative, randomized, crossover, Phase I study in 24 healthy adults. Each participant received six injections in the abdomen area of either a 2 or 3 mL placebo solution, with three different fluid viscosities (1, 8–10, and 15–20 cP combined with two different injection flow rates (0.02 and 0.3 mL/s. All injections were performed with 50 mL syringes and 27G, 6 mm needles. Perceived injection pain was assessed using a 100 mm visual analog scale (VAS (0 mm/no pain, 100 mm/extreme pain. The location and depth of the injected fluid was assessed through 2D ultrasound echography images. Results: Viscosity levels had significant impact on perceived injection pain (P=0.0003. Specifically, less pain was associated with high viscosity (VAS =12.6 mm than medium (VAS =16.6 mm or low (VAS =22.1 mm viscosities, with a significant difference between high and low viscosities (P=0.0002. Target injection volume of 2 or 3 mL was demonstrated to have no significant impact on perceived injection pain (P=0.89. Slow (0.02 mL/s or fast (0.30 mL/s injection rates also showed no significant impact on perceived pain during SC injection (P=0.79. In 92% of injections, the injected fluid was located exclusively in SC tissue whereas the remaining injected fluids were found located in SC and/or intradermal layers. Conclusion: The results of this study suggest that solutions of up to 3 mL and up to 15–20 cP injected into the abdomen within 10 seconds are well tolerated without pain. High

  13. Retro-review of flow injection analysis

    DEFF Research Database (Denmark)

    Ruzicka, Jaromir; Hansen, Elo Harald

    2008-01-01

    It is indeed unusual for authors to review their own monograph – J. Ruzicka, E.H. Hansen, Flow Injection Analysis, 2nd Edition, Wiley, Chichester, West Sussex, UK, 1988. – and even more so if the book was published 20 years ago. Yet such an exercise might yield a perspective on the progress...... of analytical instrumentation in general and on the development of flow-injection analysis (FIA) techniques in particular. By reviewing what was written and proposed 20 years ago, it is interesting to observe what proved to be of lasting value, what became accepted, and, above all, what we missed and failed...

  14. Flow Injection Analysis in Industrial Biotechnology

    DEFF Research Database (Denmark)

    Hansen, Elo Harald; Miró, Manuel

    2009-01-01

    Flow injection analysis (FIA) is an analytical chemical continuous-flow (CF) method which in contrast to traditional CF-procedures does not rely on complete physical mixing (homogenisation) of the sample and the reagent(s) or on attaining chemical equilibria of the chemical reactions involved. Ex...... involved, so that there are no restrictions whatsoever as to the chemistries that can be implemented, even if they entail multi-step reactions. Representative bioanalytical examples of this interplay are presented....

  15. Flow Injection will be 25 years

    DEFF Research Database (Denmark)

    Hansen, Elo Harald

    1999-01-01

    The article is a brief review of the first 25 years of Flow Injection Analysis (FIA), that is, from its conception and early development in the mid-70'es at the Department of Chemistry at DTU, yet it is particularly discussing why this analytical concept has had the impact that the ensuing 10,000...

  16. Evaluation of the impact of viscosity, injection volume, and injection flow rate on subcutaneous injection tolerance

    Science.gov (United States)

    Berteau, Cecile; Filipe-Santos, Orchidée; Wang, Tao; Rojas, Humberto E; Granger, Corinne; Schwarzenbach, Florence

    2015-01-01

    Aim The primary objective of this study was to evaluate the impact of fluid injection viscosity in combination with different injection volumes and flow rates on subcutaneous (SC) injection pain tolerance. Methods The study was a single-center, comparative, randomized, crossover, Phase I study in 24 healthy adults. Each participant received six injections in the abdomen area of either a 2 or 3 mL placebo solution, with three different fluid viscosities (1, 8–10, and 15–20 cP) combined with two different injection flow rates (0.02 and 0.3 mL/s). All injections were performed with 50 mL syringes and 27G, 6 mm needles. Perceived injection pain was assessed using a 100 mm visual analog scale (VAS) (0 mm/no pain, 100 mm/extreme pain). The location and depth of the injected fluid was assessed through 2D ultrasound echography images. Results Viscosity levels had significant impact on perceived injection pain (P=0.0003). Specifically, less pain was associated with high viscosity (VAS =12.6 mm) than medium (VAS =16.6 mm) or low (VAS =22.1 mm) viscosities, with a significant difference between high and low viscosities (P=0.0002). Target injection volume of 2 or 3 mL was demonstrated to have no significant impact on perceived injection pain (P=0.89). Slow (0.02 mL/s) or fast (0.30 mL/s) injection rates also showed no significant impact on perceived pain during SC injection (P=0.79). In 92% of injections, the injected fluid was located exclusively in SC tissue whereas the remaining injected fluids were found located in SC and/or intradermal layers. Conclusion The results of this study suggest that solutions of up to 3 mL and up to 15–20 cP injected into the abdomen within 10 seconds are well tolerated without pain. High viscosity injections were shown to be the most tolerated, whereas injection volume and flow rates did not impact perceived pain. PMID:26635489

  17. Flow injection potentiometric determination of pipazethate hydrochloride.

    Science.gov (United States)

    Abdel-Ghani, N T; Shoukry, A F; el Nashar, R M

    2001-01-01

    New plastic membrane electrodes for pipazethate hydrochloride based on pipazethatium phosphotungstate, pipazethatium phosphomolybdate and a mixture of the two were prepared. The electrodes were fully characterized in terms of composition, life span, pH and temperature and were then applied to the potentiometric determination of the pipazethate ion in its pure state and pharmaceutical preparations under batch and flow injection conditions. The selectivity of the electrodes towards many inorganic cations, sugars and amino acids was also tested.

  18. Tracer injection techniques in flowing surface water

    Science.gov (United States)

    Wörman, A.

    2009-04-01

    Residence time distributions for flowing water and reactive matter are commonly used integrated properties of the transport process for determining technical issues of water resource management and in eco-hydrological science. Two general issues for tracer techniques are that the concentration-vs-time relation following a tracer injection (the breakthrough curve) gives unique transport information in different parts of the curve and separation of hydromechanical and reactive mechanisms often require simultaneous tracer injections. This presentation discusses evaluation methods for simultaneous tracer injections based on examples of tracer experiments in small rivers, streams and wetlands. Tritiated water is used as a practically inert substance to reflect the actual hydrodynamics, but other involved tracers are Cr(III)-51, P-32 and N-15. Hydromechanical, in-stream dispersion is reflected as a symmetrical spreading of the spatial concentration distribution. This requires that the transport distance over water depth is larger than about five times the flow Peclet number. Transversal retention of both inert and reactive solutes is reflected in terms of the tail of the breakthrough curve. Especially, reactive solutes can have a substantial magnification of the tailing behaviour depending on reaction rates or partitioning coefficients. To accurately discriminate between the effects of reactions and hydromechanical mixing its is relevant to use simultaneous injections of inert and reactive tracers with a sequential or integrated evaluation procedure. As an example, the slope of the P-32 tailing is consistently smaller than that of a simultaneous tritium injection in Ekeby wetland, Eskilstuna. The same applies to N-15 injected in the same experiment, but nitrogen is affected also by a systematic loss due to denitrification. Uptake in stream-bed sediments can be caused by a pumping effect arising when a variable pressure field is created on the stream bottom due to bed

  19. Redesigning flow injection after 40 years of development: Flow programming.

    Science.gov (United States)

    Ruzicka, Jaromir Jarda

    2018-01-01

    Automation of reagent based assays, by means of Flow Injection (FI), is based on sample processing, in which a sample flows continuously towards and through a detector for quantification of the target analyte. The Achilles heel of this methodology, the legacy of Auto Analyzer®, is continuous reagent consumption, and continuous generation of chemical waste. However, flow programming, assisted by recent advances in precise pumping, combined with the lab-on-valve technique, allows the FI manifold to be designed around a single confluence point through which sample and reagents are sequentially directed by means of a series of flow reversals. This approach results in sample/reagent mixing analogous to the traditional FI, reduces sample and reagent consumption, and uses the stop flow technique for enhancement of the yield of chemical reactions. The feasibility of programmable Flow Injection (pFI) is documented by example of commonly used spectrophotometric assays of, phosphate, nitrate, nitrite and glucose. Experimental details and additional information are available in online tutorial http://www.flowinjectiontutorial.com/. Copyright © 2017 Elsevier B.V. All rights reserved.

  20. Stochastic logic gate that exploits noise and polarization bistability in an optically injected VCSEL.

    Science.gov (United States)

    Perrone, Sandro; Vilaseca, Ramon; Masoller, Cristina

    2012-09-24

    We study numerically the dynamics of a vertical-cavity surface-emitting laser (VCSEL) with optical injection and show that the interplay of polarization bistability and noise yields a reliable logic output to two logic inputs. Specifically, by encoding the logic inputs in the strength of the light injected into the suppressed polarization mode of the VCSEL (the so-called 'orthogonal' injection), and by decoding the output logic response from the polarization state of the emitted light, we demonstrate an all-optical stochastic logic gate that exploits the ubiquitous presence of noise. It gives the correct logic output response for as short as 5 ns bit times when the dimensionless spontaneous emission coefficient, β(sp), is within the range 10(-4)-10(-1). Considering that typical values of β(sp) in semiconductor lasers are in the range 10(-5)-10(-4), the VCSEL-based logic gate can be implemented with nowadays commercially available VCSELs, exploiting either their intrinsic noise, or external and background noise sources.

  1. A critical comparison of analytical flow systems exploiting streamlined and pulsed flows.

    Science.gov (United States)

    Dias, Ana C B; Santos, Joâo L M; Lima, José L F C; Quintella, Cristina M; Lima, Angelo M V; Zagatto, Elias A G

    2007-07-01

    Multipumping (MPFS) and multicommuted (MCFS) flow systems relying on pulsed and laminar flows were critically compared. The mixing conditions and dispersion associated with both systems were evaluated by simulating the sample with bromocresol green. The molybdenum blue method for phosphate determination in soil extracts was also implemented in both flow systems. Furthermore, laser-induced fluorescence (LIF) was applied to visualize the dispersing sample; rhodamine B was used as the fluorescent species. The pulsed flow enhanced the mixing of the solutions involved, thus reducing reagent consumption (48 and 96 microl for MPFS and MCFS), and improving sampling rate (67 and 144 h(-1) for MCFS and MPFS). For phosphate determination, results obtained with both systems were precise (r.s.d. < 0.5%; n = 10) and accurate. Analyses of the absorbance vs time/space LIF plots revealed that exploitation of pulsed flow led to a pronounced radial dispersion and to a limited axial dispersion, typical aspects of turbulent flows.

  2. CRISPR-Cas systems exploit viral DNA injection to establish and maintain adaptive immunity.

    Science.gov (United States)

    Modell, Joshua W; Jiang, Wenyan; Marraffini, Luciano A

    2017-04-06

    Clustered regularly interspaced short palindromic repeats (CRISPR)-Cas systems provide protection against viral and plasmid infection by capturing short DNA sequences from these invaders and integrating them into the CRISPR locus of the prokaryotic host. These sequences, known as spacers, are transcribed into short CRISPR RNA guides that specify the cleavage site of Cas nucleases in the genome of the invader. It is not known when spacer sequences are acquired during viral infection. Here, to investigate this, we tracked spacer acquisition in Staphylococcus aureus cells harbouring a type II CRISPR-Cas9 system after infection with the staphylococcal bacteriophage ϕ12. We found that new spacers were acquired immediately after infection preferentially from the cos site, the viral free DNA end that is first injected into the cell. Analysis of spacer acquisition after infection with mutant phages demonstrated that most spacers are acquired during DNA injection, but not during other stages of the viral cycle that produce free DNA ends, such as DNA replication or packaging. Finally, we showed that spacers acquired from early-injected genomic regions, which direct Cas9 cleavage of the viral DNA immediately after infection, provide better immunity than spacers acquired from late-injected regions. Our results reveal that CRISPR-Cas systems exploit the phage life cycle to generate a pattern of spacer acquisition that ensures a successful CRISPR immune response.

  3. Flow injection potentiometric determination of amantadine HCl.

    Science.gov (United States)

    Abdel-Ghani, Nour T; Shoukry, Adel F; Hussein, Salwa H

    2002-10-15

    New amantadine (Am) ion selective plastic membrane electrodes of both conventional and coated graphite types based on the ion-pair of amantadinium tetraphenylborate (Am-TPB) ion-pair are prepared. The conventional type electrode was fully characterized in terms of membrane composition, life span, pH, ionic strength and temperature. It was applied to potentiometric determination of amantadine in pure state and pharmaceutical preparation under batch and flow injection conditions. The selectivity of the electrode toward a large number of inorganic cations, sugars and amino acids was tested. The solubility product of the ion-pair and the formation constant of the precipitation reaction leading to the ion-pair formation were determined conductimetrically. Copyright 2002 Elsevier Science B.V.

  4. [Flow injection biamperometric analysis of isoniazid].

    Science.gov (United States)

    Zhang, J C; Zhao, C; Song, J F

    2001-09-01

    To establish a simple, rapid, and accurate electrochemical method for on-line determination of isoniazid. Based on the flow injection biamperometry for irreversible couple system, and using two preanodized platinum electrodes with the applied potential difference of 0 V, the biamperometric method for the determination of isoniazid has been proposed by coupling the catalytic oxidation of isoniazid and the reduction of platinum oxide. Common excipients, inorganic ions, amino acids, vitamins and proteins do not interfere with the determination. Linear relationship between current and the concentration of isoniazid is obtained in the range of 1.0 x 10(-6)-1.0 x 10(-4) mol.L-1 (gamma = 0.998, n = 11). The RSD of 1.8% was obtained for 8 successive determinations of 1.0 x 10(-5) mol.L-1 isoniazid. The proposed method has been shown to be sensitive, selective, rapid (120 samples.h-1), and suitable for the on-line direct determination of isoniazid.

  5. Taylor-Couette flow with radial fluid injection

    Science.gov (United States)

    Wilkinson, Nikolas; Dutcher, Cari S.

    2017-08-01

    Taylor-Couette cells have been shown to improve a number of industrial processes due to the wide variety of hydrodynamic flow states accessible. Traditional designs, however, limit the ability to introduce new fluids into the annulus during device operation due to geometric confinement and complexity. In this paper, a co- and counter-rotating Taylor-Couette cell with radial fluid injection has been constructed. The incorporation of 16 ports in the inner cylinder enables radial fluid injection during rotation of both cylinders. The design is also capable of continuous axial flow, enabling large injection volumes. The new inner cylinder design does not modify the critical Re for flow instabilities and can precisely inject a desired mass at a desired flow rate. A range of injection rates and masses were explored to quantify the effect of radial injection on the stability of the turbulent Taylor vortex structure. Only the highest injection rate and total mass studied (5.9 g/s, 100 g) modified the turbulent Taylor vortex structure after injection for a sustained period. The post-injection vortices remained larger than the pre-injection vortices, whereas at lower injection rates or masses, the vortex structure quickly returned to the pre-injection structure. This new system allows for in situ study of hydrodynamic effects on fluid-fluid (gas and liquid) mixing and multiphase complexation, growth, and structure. We demonstrated this new design's potential for studying the flocculation of bentonite using cationic polyacrylamide for enhancing water treatment operations.

  6. Flow-injection biamperometry of pyrogallol compounds.

    Science.gov (United States)

    Zhao, Chuan; Song, Junfeng; Zhang, Juncai

    2003-01-02

    A biamperometric method for the direct determination of pyrogallol compounds has been designed for flow-injection analysis. The method is based on the electrocatalytic oxidation of pyrogallol compounds at one pretreated platinum electrode and the reduction of platinum oxide at the other pretreated platinum electrode to form a biamperometric detection system with the applied potential difference of 10 mV. Three important compounds, pyrogallol, gallic acid and tannic acid, have been detected by the method. The linear relationships between currents and the concentrations of pyrogallol, gallic acid and tannic acid are obtained over the range 1.0x10(-6)-1.0x10(-4), 1.0x10(-6)-1.0x10(-4) and 1.0x10(-6)-2.0x10(-4) mol l(-1) with the detection limit of 6.0x10(-7), 6.0x10(-7) and 8.0x10(-7) mol l(-1) (S/N=2), respectively. The R.S.D. observed for 30 successive determinations of 5.0x10(-5) mol l(-1) pyrogallol, gallic acid and tannic acid are 1.9, 2.5 and 2.0%, respectively. Most ions and organic compounds tested are found not to cause significant interference in the determinations. The method is simple, selective and efficient (180 h(-1)), performing well as a routine assay, and has been validated by the determination of pyrogallol compounds in tea and Chinese gall.

  7. Load Flow Analysis of a 15Mva Injection Substation | Oshevire ...

    African Journals Online (AJOL)

    This study presents the load flow analysis of Otovwodo 33/11kV injection substation, Nigeria. It is an obvious fact that the planning, design and operation of power systems require load flow calculations to analyze the steady state of the system under various operating conditions, and equipment configuration. This load flow ...

  8. Sequential injection lab-on-valve: the third generation of flow injection analysis

    DEFF Research Database (Denmark)

    Wang, Jianhua; Hansen, Elo Harald

    2003-01-01

    -LOV approach as well as its applications in the automation and micro-miniaturization of on-line sample pre-treatment. Special emphasis is placed on using SI-LOV in conjunction with bead injection (BI) for on-line separation and pre-concentration of ultra-trace levels of metals by exploiting the renewable micro...

  9. Flow systems exploiting in-line prior assays.

    Science.gov (United States)

    Grassi, Viviane; Dias, Ana Cristi B; Zagatto, Elias A G

    2004-12-15

    An expert sequential injection system involving a prior assay is proposed for spectrophotometric determination of phosphate and eventually zinc in soil extracts. The result of phosphate determination is the basis for a concentration-oriented decision regarding to the need or not for zinc determination. Zinc was only determined if a threshold value (peak height corresponding to 5.0mgl(-1)P) was surpassed. The methods involved formation of molybdenum blue and the Rhodamine 6G/ammonium thiocyanate/Zn(2+) ternary complex. Variations in the threshold value were < 2% during 4h operating periods, false responses were not verified, and the analytical time was reduced in about 30%. Precise results (R.S.D. <3%P and < 1% Zn) in agreement with spectrophotometry and flame atomic absorption spectrometry were obtained. The innovation permits faster information processing, as well as a reduction in the number of measurements, number of analytical steps, laboratorial time, and consumption of sample and reagents, thus waste generation.

  10. Tre generationer af Flow Injection Analysis

    DEFF Research Database (Denmark)

    Hansen, Elo Harald; Chomchoei, Roongrat; Long, Xiangbao

    2004-01-01

    Siden introduktionen af FIA har en række videreudviklinger resulteret i Sequential Injection Analysis (SIA) og senest i Lab-on-Valve (LOV)-metodikken. Her beskrives disse, og der gives eksempler på, hvordan metoderne kan bruges til at bestemme sporstofkoncentrationer af metaller i komplekse...

  11. Exploiting an automated microfluidic hydrodynamic sequential injection system for determination of phosphate.

    Science.gov (United States)

    Khongpet, Wanpen; Pencharee, Somkid; Puangpila, Chanida; Kradtap Hartwell, Supaporn; Lapanantnoppakhun, Somchai; Jakmunee, Jaroon

    2018-01-15

    A microfluidic hydrodynamic sequential injection (μHSI) spectrophotometric system was designed and fabricated. The system was built by laser engraving a manifold pattern on an acrylic block and sealing with another flat acrylic plate to form a microfluidic channel platform. The platform was incorporated with small solenoid valves to obtain a portable setup for programmable control of the liquid flow into the channel according to the HSI principle. The system was demonstrated for the determination of phosphate using a molybdenum blue method. An ascorbic acid, standard or sample, and acidic molybdate solutions were sequentially aspirated to fill the channel forming a stack zone before flowing to the detector. Under the optimum condition, a linear calibration graph in the range of 0.1-6mg P L-1 was obtained. The detection limit was 0.1mgL-1. The system is compact (5.0mm thick, 80mm wide × 140mm long), durable, portable, cost-effective, and consumes little amount of chemicals (83μL each of molybdate and ascorbic acid, 133μL of the sample solution and 1.7mL of water carrier/run). It was applied for the determination of phosphate content in extracted soil samples. The percent recoveries of the analysis were obtained in the range of 91.2-107.3. The results obtained agreed well with those of the batch spectrophotometric method. Copyright © 2017 Elsevier B.V. All rights reserved.

  12. Electroosmotic flow and injection: application to conductimetry.

    Science.gov (United States)

    Tang, L; Huber, C O

    1994-10-01

    Electroosmotic solution propulsion and sample injection using fused silica tube was investigated. Capillary tube dimensions were 50-100 microm i.d. by 4-7 cm length with a break in the capillary wall near one end through which electrolytic contact with the capillary solution was established. The applied field was typically 150 V/cm. The voltage at the break in the column was monitored by potentiometry with a bridge configuration. Concentrations ranging from 10 microM to 100 mM were accommodated. The basis for high sensitivity, e.g. 70 mV/microM, together with low cell volume, e.g. 20 nl, was established. Tap water conductivity measurements were made using CaCl(2) reference solution.

  13. Material flow data for numerical simulation of powder injection molding

    Science.gov (United States)

    Duretek, I.; Holzer, C.

    2017-01-01

    The powder injection molding (PIM) process is a cost efficient and important net-shape manufacturing process that is not completely understood. For the application of simulation programs for the powder injection molding process, apart from suitable physical models, exact material data and in particular knowledge of the flow behavior are essential in order to get precise numerical results. The flow processes of highly filled polymers are complex. Occurring effects are very hard to separate, like shear flow with yield stress, wall slip, elastic effects, etc. Furthermore, the occurrence of phase separation due to the multi-phase composition of compounds is quite probable. In this work, the flow behavior of a 316L stainless steel feedstock for powder injection molding was investigated. Additionally, the influence of pre-shearing on the flow behavior of PIM-feedstocks under practical conditions was examined and evaluated by a special PIM injection molding machine rheometer. In order to have a better understanding of key factors of PIM during the injection step, 3D non-isothermal numerical simulations were conducted with a commercial injection molding simulation software using experimental feedstock properties. The simulation results were compared with the experimental results. The mold filling studies amply illustrate the effect of mold temperature on the filling behavior during the mold filling stage. Moreover, the rheological measurements showed that at low shear rates no zero shear viscosity was observed, but instead the viscosity further increased strongly. This flow behavior could be described with the Cross-WLF approach with Herschel-Bulkley extension very well.

  14. Exploiting biased reptation for continuous flow preparative DNA fractionation in a versatile microfluidic platform

    NARCIS (Netherlands)

    Gümüscü, B.; Bomer, Johan G.; de Boer, Hans L.; van den Berg, Albert; Eijkel, Jan C.T.

    2017-01-01

    A new approach is presented for preparative, continuous flow fractionation of sub-10-kbp DNA fragments, which exploits the variation in the field-dependent mobility of the DNA molecules based on their length. Orthogonally pulsed electric fields of significantly different magnitudes are applied to a

  15. The Impact of Flow Injection on Modern Chemical Analysis

    DEFF Research Database (Denmark)

    Hansen, Elo Harald

    There is no doubt that Flow Injection Analysis (FIA) has had a profound impact on the ways and means that modern analytical chemical procedures are performed. This is amply reflected in the voluminous scientific literature, which by the middle of 2004 passed more than 14,500 FIA-publications in i......There is no doubt that Flow Injection Analysis (FIA) has had a profound impact on the ways and means that modern analytical chemical procedures are performed. This is amply reflected in the voluminous scientific literature, which by the middle of 2004 passed more than 14,500 FIA...

  16. Flow improvers for water injection based on surfactants

    Energy Technology Data Exchange (ETDEWEB)

    Oskarsson, H.; Uneback, I.; Hellsten, M.

    2006-03-15

    In many cases it is desirable to increase the flow of injection water when an oil well deteriorates. It is very costly in offshore operation to lay down an additional water pipe to the injection site. Flow improvers for the injection water will thus be the most cost-effective way to increase the flow rate. During the last years water-soluble polymers have also been applied for this purpose. These drag-reducing polymers are however only slowly biodegraded which has been an incentive for the development of readily biodegradable surfactants as flow improvers for injection water. A combination of a zwitterionic and an anionic surfactant has been tested in a 5.5 inch, 700 m long flow loop containing sulphate brine with salinity similar to sea water. A drag reduction between 75 and 80% was achieved with 119 ppm in solution of the surfactant blend at an average velocity of 1.9 m/s and between 50 and 55% at 2.9 m/s. The surfactants in this formulation were also found to be readily biodegradable in sea water and low bio accumulating which means they have an improved environmental profile compared to the polymers used today. Due to the self-healing properties of the drag-reducing structures formed by surfactants, these may be added before the pump section - contrary to polymers which are permanently destroyed by high shear forces. (Author)

  17. Toroidal flow measurement in CT injected STOR-M tokamak

    Science.gov (United States)

    Asai, Tomohiko; Morelli, Jordan; Singh, Ajay; Xiao, Chijin; Hirose, Akira; Nagata, Masayoshi; Uyama, Tadao

    2002-11-01

    Compact Torus (CT) injection is a technology being developed for fueling of large tokamak reactors. It has been demonstrated in the STOR-M tokamak that tangential CT injection is capable of inducing an improved confinement mode (H-mode). It has been conjectured that tangential CT injection may enhance the toroidal rotation of the bulk tokamak plasma which is responsible for the H-mode by preventing or reducing microinstabilities[1]. In order to investigate the mechanisms of the L-H transition induced by enhanced toroidal flow (particularly that caused by CT injection), an Ion Doppler Spectroscope (IDS) has been developed. The IDS employs a 0.75 m focal length Czerny-Turner spectrometer with a resolution of 0.1 Åand a 16-channel PMT array. Data of plasma flow measurements will be presented with and without CT injection. Also, the results will be compared with toroidal flow measurement obtained using a 4-sided Mach probe in the plasma edge region. [1] S. Sen et al., Phys. Rev. Lett. 88, 185001 (2002).

  18. Determination of Acidity Constants by Gradient Flow-Injection Titration

    Science.gov (United States)

    Conceicao, Antonio C. L.; Minas da Piedade, Manuel E.

    2006-01-01

    A three-hour laboratory experiment, designed for an advanced undergraduate course in instrumental analysis that illustrates the application of the gradient chamber flow-injection titration (GCFIT) method with spectrophotometric detection to determine acidity constants is presented. The procedure involves the use of an acid-base indicator to obtain…

  19. Immobilization of alliinase and its application: Flow injection ...

    African Journals Online (AJOL)

    For the immobilized alliinase, the highest activity was allowed at pH of 7.0 and temperature at 35°C. Besides, the immobilized enzyme showed good thermal and pH stabilities. The flow-injection enzymatic analytical system based on the immobilized alliinase and an ammonia gas electrode provided linearity in the 1 × 10-5 ...

  20. Flow Injection Analysis: A Revolution in Modern Analytical Chemistry

    DEFF Research Database (Denmark)

    Hansen, Elo Harald

    1996-01-01

    A review is made of the fundamentals of Flow Injection Analysis (FIA), and the versatility and applicability of this analytical concept is demonstrated by a series of examples, comprizing the use of different types of FIA-manifolds and various detection devices (optical and electrochemical). Emph...

  1. A critical comparison of constant and pulsed flow systems exploiting gas diffusion.

    Science.gov (United States)

    Silva, Claudineia Rodrigues; Henriquez, Camelia; Frizzarin, Rejane Mara; Zagatto, Elias Ayres Guidetti; Cerda, Victor

    2016-02-01

    Considering the beneficial aspects arising from the implementation of pulsed flows in flow analysis, and the relevance of in-line gas diffusion as an analyte separation/concentration step, influence of flow pattern in flow systems with in-line gas diffusion was critically investigated. To this end, constant or pulsed flows delivered by syringe or solenoid pumps were exploited. For each flow pattern, two variants involving different interaction times of the donor with the acceptor streams were studied. In the first one, both the acceptor and donor streams were continuously flowing, whereas in the second one, the acceptor was stopped during the gas diffusion step. Four different volatile species (ammonia, ethanol, carbon dioxide and hydrogen sulfide) were selected as models. For the flow patterns and variants studied, the efficiencies of mass transport in the gas diffusion process were compared, and sensitivity, repeatability, sampling frequency and recorded peak shape were evaluated. Analysis of the results revealed that sensitivity is strongly dependent on the implemented variant, and that flow pattern is an important feature in flow systems with in-line gas diffusion. Copyright © 2015 Elsevier B.V. All rights reserved.

  2. Flow bouncing and electron injection observed by Cluster: FLOW BOUNCING AND ELECTRON INJECTION OBSERVED BY CLUSTER

    National Research Council Canada - National Science Library

    Nakamura, R; Baumjohann, W; Panov, E; Volwerk, M; Birn, J; Artemyev, A; Petrukovich, A. A; Amm, O; Juusola, L; Kubyshkina, M. V; Apatenkov, S; Kronberg, E. A; Daly, P. W; Fillingim, M; Weygand, J. M; Fazakerley, A; Khotyaintsev, Y

    2013-01-01

    ... accompanied by enhanced flux of energetic electrons were observed before the flow bouncing. The sequence of events started with a localized dipolarization front and ended with a large scale (>10RE) dipolarization front accompanied by a major increase in energetic electrons at all spacecraft and immediately followed by flow bouncing. Multiple dipolariz...

  3. Theory of Gas Injection: Interaction of Phase Behavior and Flow

    Science.gov (United States)

    Dindoruk, B.

    2015-12-01

    The theory of gas injection processes is a central element required to understand how components move and partition in the reservoir as one fluid is displacing another (i.e., gas is displacing oil). There is significant amount of work done in the area of interaction of phase-behavior and flow in multiphase flow conditions. We would like to present how the theory of gas injection is used in the industry to understand/design reservoir processes in various ways. The tools that are developed for the theory of gas injection originates from the fractional flow theory, as the first solution proposed by Buckley-Leveret in 1940's, for water displacing oil in porous media. After 1960's more and more complex/coupled equations were solved using the initial concept(s) developed by Buckley-Leverett, and then Welge et al. and others. However, the systematic use of the fractional flow theory for coupled set of equations that involves phase relationships (EOS) and phase appearance and disappearance was mainly due to the theory developed by Helfferich in early 80's (in petroleum literature) using method of characteristics primarily for gas injection process and later on by the systematic work done by Orr and his co-researchers during the last two decades. In this talk, we will present various cases that use and extend the theory developed by Helfferich and others (Orr et al., Lake et al. etc.). The review of various injection systems reveals that displacement in porous media has commonalities that can be represented with a unified theory for a class of problems originating from the theory of gas injection (which is in a way generalized Buckley-Leverett problem). The outcome of these solutions can be used for (and are not limited to): 1) Benchmark solutions for reservoir simulators (to quantify numerical dispersion, test numerical algorithms) 2) Streamline simulators 3) Design of laboratory experiments and their use (to invert the results) 4) Conceptual learning and to investigate

  4. Flow Simulation of Solid Rocket Motors. 1; Injection Induced Water-Flow Tests from Porous Media

    Science.gov (United States)

    Ramachandran, N.; Yeh, Y. P.; Smith, A. W.; Heaman, J. P.

    1999-01-01

    Prior to selecting a proper porous material for use in simulating the internal port flow of a solid rocket motor (SRM), in cold-flow testing, the flow emerging from porous materials is experimentally investigated. The injection-flow emerging from a porous matrix always exhibits a lumpy velocity profile that is spatially stable and affects the development of the longitudinal port flow. This flow instability, termed pseudoturbulence, is an inherent signature of the porous matrix and is found to generally increase with the wall porosity and with the injection flow rate. Visualization studies further show that the flow from porous walls made from shaving-type material (sintered stainless-steel) exhibits strong recirculation zones that are conspicuously absent in walls made from nodular or spherical material (sintered bronze). Detailed flow visualization observations and hot-film measurements are reported from tests of injection-flow and a coupled cross-flow from different porous wall materials. Based on the experimental data, discussion is provided on the choice of suitable material for SRM model testing while addressing the consequences and shortcomings from such a test.

  5. Spectrophotometric flow injection monitoring of sulfide during sugar fermentation.

    Science.gov (United States)

    Silva, Claudineia R; Barros, Valdemir A F; Basso, Luiz C; Zagatto, Elias A G

    2011-09-15

    A spectrophotometric flow injection procedure involving N,N-dimethyl-p-phenylenediamine (DMPD) is applied to the sulfide monitoring of a sugar fermentation by Saccharomyces cerevisiae under laboratory conditions. The gaseous chemical species evolving from the fermentative process, mainly CO(2), are trapped allowing a cleaned sample aliquot to be collected and introduced into the flow injection analyzer. Measurement rate, signal repeatability, detection limit and reagent consumption per measurement were estimated as 150 h(-1), 0.36% (n=20), 0.014 mg L(-1) S and 120 μg DMPD, respectively. The main characteristics of the monitoring record are discussed. The strategy is worthwhile for selecting yeast strain, increasing the industrial ethanol production and improving the quality of wines. Copyright © 2011. Published by Elsevier B.V.

  6. Recent developments in automatic solid-phase extraction with renewable surfaces exploiting flow-based approaches

    DEFF Research Database (Denmark)

    Miró, Manuel; Hartwell, Supaporn Kradtap; Jakmunee, Jaroon

    2008-01-01

    Solid-phase extraction (SPE) is the most versatile sample-processing method for removal of interfering species and/or analyte enrichment. Although significant advances have been made over the past two decades in automating the entire analytical protocol involving SPE via flow-injection approaches...... chemical-derivatization reactions, and it pinpoints the most common instrumental detection techniques utilized. We present and discuss in detail relevant environmental and bioanalytical applications reported in the past few years....

  7. Spectrophotometric flow-injection determination of sulphate in soil solutions.

    Science.gov (United States)

    Meneses, Silvia R P; Maniasso, Nelson; Zagatto, Elias A G

    2005-03-15

    A flow-injection procedure for spectrophotometric determination of sulphate in soil solutions is proposed. Samples are directly soaked from the soils under field conditions, in-line filtered through ceramic plates, and preserved with thymol. The method involves reaction with barium dimethylsulphonazo(III) (DMSA) in the presence of dimethylsulphoxide (DMSO) with further measuring the decrease in absorbance at 668nm. A linear response is observed up to about 5mgl(-1) SO(4), and detection limit (3sigma criterion) is 0.1mgl(-1) SO(4). Only 4.5mug DMSA is consumed per determination. The system is rugged and baseline drift is not observed during extended operation periods. About 60 samples are injected per hour, and the results are precise (r.s.d. <2%) and in agreement with ion chromatography.

  8. Flow injection analysis of some oxidants using spectrophotometric detection

    Directory of Open Access Journals (Sweden)

    Ibrahim Z. AL-Zamil

    2015-09-01

    Full Text Available A spectrophotometric flow-injection method has been devised for the determination of nanomole quantities of some oxidants i.e. iodate, periodate, permanganate and hydrogen peroxide. The method is based on the oxidation of iron(II to iron(III and the measurement of the absorbance of the red iron(III–thiocyanate complex at 485 nm. The optimal oxidation pH and the linearity ranges of the calibration curves have been investigated. The analytical aspects of the method including the statistical evaluation of the results are discussed. The analysis of some authentic samples showed an average percentage recovery of 99%.

  9. Determination of Thiocyanate by Kinetic Spectrophotometric Flow Injection Analysis

    Directory of Open Access Journals (Sweden)

    Mohsen Keyvanfard

    2013-01-01

    Full Text Available A simple and rapid flow injection spectrophotometric method has been developed for the determination of amount of thiocyanate in wastewaters and well water samples. It is based on the reaction of thiocyanate in hydrochloric acid with janus green and bromate. Reaction was monitored spectrophotometrically by measuring janus green absorbance at λmax=554 nm. The calibration graph was linear over the range 0.02–1.0 μg mL−1 and the detection limit was 0.016 μg mL−1 (s/n=3. The throughput was 25 samples per hour.

  10. Principles and Applications of Flow Injection Analysis in Biosensors

    DEFF Research Database (Denmark)

    Hansen, Elo Harald

    1996-01-01

    In practical applications biosensors are often forced to operate under less than optimal conditions. Because of their construction, and the physical processes and chemical reactions involved in their operation, compromise conditions are frequently required to synchronize all events taking place....... Therefore, and in order to implement functions such as periodic calibration, conditioning and possible regeneration of the biosensor, and, very importantly, to yield the freedom to select the optimum detection means, it is advantageous to use these devices in a flow-through mode, particularly by employing...... the flow injection (FI) approach. The capacity of FI, as offering itself as a complementary facility to augment the performance of biosensors, and in many cases as an attractive alternative, is demonstrated by reference to selected examples, comprising assays based on enzymatic procedures with optical...

  11. Flow-Injection Responses of Diffusion Processes and Chemical Reactions

    DEFF Research Database (Denmark)

    Andersen, Jens Enevold Thaulov

    2000-01-01

    The technique of Flow-injection Analysis (FIA), now aged 25 years, offers unique analytical methods that are fast, reliable and consuming an absolute minimum of chemicals. These advantages together with its inherent feasibility for automation warrant the future applications of FIA as an attractiv...... be used in the resolution of FIA profiles to obtain information about the content of interference’s, in the study of chemical reaction kinetics and to measure absolute concentrations within the FIA-detector cell....... manifold may be characterised by a diffusion coefficient that depends on flow rate, denoted as the kinematic diffusion coefficient. The description was applied to systems involving species of chromium, both in the case of simple diffusion and in the case of chemical reactions. It is suggested that it may...

  12. Screening for ochratoxin A in blood by flow injection analysis.

    Science.gov (United States)

    Hult, K; Fuchs, R; Peraica, M; Plestina, R; Ceović, S

    1984-12-01

    A micromethod for ochratoxin A detection in human sera by flow injection technique is described. The method requires 50 microliter of sera, and it is designed to distinguish samples containing less than 10 ng ochratoxin A per ml. The method is based on fluorescence measurement following a simple extraction procedure for which very small amounts of chemicals are needed. Since the method is not confirmatory, all samples showing fluorescence above a certain intensity have to be reanalysed with some other method where a confirmation step in included. Because of the small amount of serum needed and the rapid procedure (less than 15 min), a large number of samples can be analysed very quickly. The method may therefore be applicable for large screening campaigns conducted to determine the presence of ochratoxin A in blood. This conclusion is based on 1675 samples and 147 standards analysed concurrently by the flow injection technique and an earlier published enzymic method. The method is also suitable for monitoring ochratoxin A levels in the blood of experimental animals.

  13. Assessing preferential flow by simultaneously injecting nanoparticle and chemical tracers

    KAUST Repository

    Subramanian, S. K.

    2013-01-01

    The exact manner in which preferential (e.g., much faster than average) flow occurs in the subsurface through small fractures or permeable connected pathways of other kinds is important to many processes but is difficult to determine, because most chemical tracers diffuse quickly enough from small flow channels that they appear to move more uniformly through the rock than they actually do. We show how preferential flow can be assessed by injecting 2 to 5 nm carbon particles (C-Dots) and an inert KBr chemical tracer at different flow rates into a permeable core channel that is surrounded by a less permeable matrix in laboratory apparatus of three different designs. When the KBr tracer has a long enough transit through the system to diffuse into the matrix, but the C-Dot tracer does not, the C-Dot tracer arrives first and the KBr tracer later, and the separation measures the degree of preferential flow. Tracer sequestration in the matrix can be estimated with a Peclet number, and this is useful for experiment design. A model is used to determine the best fitting core and matrix dispersion parameters and refine estimates of the core and matrix porosities. Almost the same parameter values explain all experiments. The methods demonstrated in the laboratory can be applied to field tests. If nanoparticles can be designed that do not stick while flowing through the subsurface, the methods presented here could be used to determine the degree of fracture control in natural environments, and this capability would have very wide ranging value and applicability.

  14. An improved flow-injection system for spectrophotometric determination of molybdenum and tungsten in tool steels.

    Science.gov (United States)

    Gervasio, Ana P G; Fortes, Paula R; Meneses, Silvia R P; Miranda, Carlos E S; Zagatto, Elias A G

    2006-06-15

    A flow-injection procedure for simultaneous spectrophotometric determination of tungsten and molybdenum in steel alloys is proposed. The method exploits the catalytic effects of Mo(VI) and W(VI) on the rate of iodide oxidation by hydrogen peroxide under acidic conditions. A novel strategy for ion-exchange separation of the potential interfering species is proposed, and an AG50W-X8 cationic resin mini-column is used. The sample is injected twice, originating two sequential plugs, citrate being added to one of them in order to suppress the W(VI) catalytic activity thus providing the kinetic discrimination. The system handles 70 samples per hour and requires 1.6mg KI per determination. A linear response is verified up to 10mgl(-1) Mo (or W) in the injectate, and signal additivity is 98-103%. Results are precise (R.S.D.<0.04) and in agreement with ICP-OES. Running a standard reference material (IPT-50) assessed also accuracy.

  15. Method for 236U Determination in Seawater Using Flow Injection Extraction Chromatography and Accelerator Mass Spectrometry

    DEFF Research Database (Denmark)

    Qiao, Jixin; Hou, Xiaolin; Steier, Peter

    2015-01-01

    experimental parameters affecting the analytical effectiveness were investigated and optimized in order to achieve high chemical yields and simple and rapid analysis as well as low procedure background. Besides, the operational conditions for the target preparation prior to the AMS measurement were optimized......, on the basis of studying the coprecipitation behavior of uranium with iron hydroxide. The analytical results indicate that the developed method is simple and robust, providing satisfactory chemical yields (80−100%) and high analysis speed (4 h/sample), which could be an appealing alternative to conventional......An automated analytical method implemented in a flow injection (FI) system was developed for rapid determination of 236U in 10 L seawater samples. 238U was used as a chemical yield tracer for the whole procedure, in which extraction chromatography (UTEVA) was exploited to purify uranium, after...

  16. Cross-correlation in flow-injection analysis with parallel flow streams and amperometric detection.

    Science.gov (United States)

    McKean, R E; Curran, D J

    1992-03-01

    Cross-correlation was implemented for flow-injection analysis by using two parallel flow lines, each with amperometric detectors, and driven by peristaltic pumps. One flow line was used to generate the reference signal for an analog correlator circuit and the other to generate the analyte signal. Cross-correlation was performed by multiplying these signals together at a time delay of zero, followed by low pass filtering. Using dopamine as a test system, improvements in signal-to-noise ratios of about two orders of magnitude were found for the correlation signal over the direct measurement of the electrode current.

  17. Exploitation of a single interface flow system for on-line aqueous biphasic extraction.

    Science.gov (United States)

    Silvestre, Cristina I C; Rodrigues, Sofia; Santos, João L M; Lima, José L F C; Zagatto, Elias A G

    2010-06-15

    The exploitation of aqueous biphasic extraction is proposed for the first time in flow analysis. This extraction strategy stands out for being environmentally attractive since it is based in the utilization of two immiscible phases that are intrinsically aqueous. The organic solvents of the traditional liquid-liquid extractions are no longer used, being replaced by non-toxic, non-flammable and non-volatile ones. A single interface flow analysis (SIFA) system was implemented to carry out the extraction process due to its favourable operational characteristics that include the high automation level and simplicity of operation, the establishment of a dynamic interface where the mass transfer occurred between the two immiscible aqueous phases, and the versatile control over the extraction process namely the extraction time. The application selected to demonstrate the feasibility of SIFA to perform this aqueous biphasic extraction was the pre-concentration of lead. After extraction, lead reacted with 8-hydroxyquinoline-5-sulfonic acid and the resulting product was determined by a fluorimetric detector included in the flow manifold. Therefore, the SIFA single interface was used both as extraction (enrichment) and reaction interface.

  18. Spectrophotometric flow-injection determination of nickel in biological materials.

    Science.gov (United States)

    Vicente, Simone; Maniasso, Nelson; Queiroz, Zilvanir F; Zagatto, Elias A G

    2002-05-24

    A flow-injection procedure is proposed for the spectrophotometric determination of nickel in plants and foodstuffs using 2-(5-brom-2-pyridylazo)-5-(diethylamino)-phenol (Br-PADAP) as colour-forming reagent. Tolerance to the presence of potential interferants is enhanced by adding sodium pyrophosphate to the reaction medium and by coupling a C(18) mini-column with immobilised 1-(2-thiazolylazo)-2-naphthol to the manifold. Linearity of the analytical curve is observed within 0.025 and 0.50 mgl(-1) Ni (r=0.9997, n=8), and detection limit is 17 mugl(-1) Ni. Precise results (r.s.d. approximately 1%) in agreement with certified values of standard reference materials are obtained at a sampling rate of 90 h(-1) that means 0.47 mug Br-PADAP per determination.

  19. The impact of interpreted flow regimes during constant head injection tests on the estimated transmissivity from injection tests and difference flow logging

    Energy Technology Data Exchange (ETDEWEB)

    Hjerne, Calle; Ludvigsson, Jan-Erik; Harrstroem, Johan [Geosigma AB, Uppsala (Sweden)

    2013-04-15

    A large number of constant head injection tests were carried out in the site investigation at Forsmark using the Pipe String System, PSS3. During the original evaluation of the tests the dominating transient flow regimes during both the injection and recovery period were interpreted together with estimation of hydraulic parameters. The flow regimes represent different flow and boundary conditions during the tests. Different boreholes or borehole intervals may display different distributions of flow regimes. In some boreholes good agreement was obtained between the results of the injection tests and difference flow logging with Posiva flow log (PFL) but in other boreholes significant discrepancies were found. The main objective of this project is to study the correlation between transient flow regimes from the injection tests and other borehole features such as transmissivity, depth, geology, fracturing etc. Another subject studied is whether observed discrepancies between estimated transmissivity from difference flow logging and injection tests can be correlated to interpreted flow regimes. Finally, a detailed comparison between transient and stationary evaluation of transmissivity from the injection tests in relation to estimated transmissivity from PFL tests in corresponding sections is made. Results from previous injection tests in 5 m sections in boreholes KFM04, KFM08A and KFM10A were used. Only injection tests above the (test-specific) measurement limit regarding flow rate are included in the analyses. For all of these tests transient flow regimes were interpreted. In addition, results from difference flow logging in the corresponding 5 m test sections were used. Finally, geological data of fractures together with rock and fracture zone properties have been used in the correlations. Flow regimes interpreted from the injection period of the tests are generally used in the correlations but deviations between the interpreted flow regimes from the injection and

  20. Direct introduction of water sample in multisegmented flow-injection analysis for sulfide determination.

    Science.gov (United States)

    Lima, Giovana F; Brondi, Ariadne M; Paiva, Ana L S F; Tarley, César R T; de Oliveira, André F; Wisniewski, Célio; Luccas, Pedro O

    2011-01-01

    The present paper describes an inline flow-injection analysis system for the determination of sulfide in water samples, exploiting the Fischer reaction. Water samples were collected and introduced into a reactor of the FIA system. The sulfide released, after sample acidification, was carried out with a nitrogen gas flow and mixed with N,N diethyl-p-phenylenediamine (DEPD) solution in the presence of Fe(III). The blue dye formed was measured in the wavelength range between 672-679 nm. An evaluation of the effects of chemical and flow factors was performed using the factorial design of two levels, while optimization was accomplished by a Doehlert matrix. The system presented two linear-response ranges: the first of 0.433 to 400 µg L(-1) and the second of 400 to 3500 µg L(-1). The detection and quantification limit were found to be 0.130 and 0.433 µg L(-1), respectively, while the sample throughput was 12 h(-1). The precision was evaluated as the relative standard deviation (n = 10); for 50 and 100 µg L(-1) sulfide it was found to be 1.9 and 2.3%, respectively. The method showed satisfactory selectivity regarding the main interference present in environmental samples. The accuracy of the method was successfully evaluated in environmental water samples after a comparison with a literature reference method.

  1. 3D-CFD Simulation of Confined Cross-Flow Injection Process Using Single Piston Pump

    Directory of Open Access Journals (Sweden)

    M. Elashmawy

    2017-12-01

    Full Text Available Injection process into a confined cross flow is quite important for many applications including chemical engineering and water desalination technology. The aim of this study is to investigate the performance of the injection process into a confined cross-flow of a round pipe using a single piston injection pump. A computational fluid dynamics (CFD analysis has been carried out to investigate the effect of the locations of the maximum velocity and minimum pressure on the confined cross-flow process. The jet trajectory is analyzed and related to the injection pump shaft angle of rotation during the injection duty cycle by focusing on the maximum instant injection flow of the piston action. Results indicate a low effect of the jet trajectory within the range related to the injection pump operational conditions. Constant cross-flow was used and injection flow is altered to vary the jet to line flow ratio (QR. The maximum jet trajectory exhibits low penetration inside the cross-flow. The results showed three regions of the flow ratio effect zones with different behaviors. Results also showed that getting closer to the injection port causes a significant decrease on the locations of the maximum velocity and minimum pressure.

  2. Exploiting the Error-Correcting Capabilities of Low Density Parity Check Codes in Distributed Video Coding using Optical Flow

    DEFF Research Database (Denmark)

    Rakêt, Lars Lau; Søgaard, Jacob; Salmistraro, Matteo

    2012-01-01

    We consider Distributed Video Coding (DVC) in presence of communication errors. First, we present DVC side information generation based on a new method of optical flow driven frame interpolation, where a highly optimized TV-L1 algorithm is used for the flow calculations and combine three flows....... Thereafter methods for exploiting the error-correcting capabilities of the LDPCA code in DVC are investigated. The proposed frame interpolation includes a symmetric flow constraint to the standard forward-backward frame interpolation scheme, which improves quality and handling of large motion. The three...... flows are combined in one solution. The proposed frame interpolation method consistently outperforms an overlapped block motion compensation scheme and a previous TV-L1 optical flow frame interpolation method with an average PSNR improvement of 1.3 dB and 2.3 dB respectively. For a GOP size of 2...

  3. Stability Analysis of High-Speed Boundary-Layer Flow with Gas Injection

    Science.gov (United States)

    2014-06-01

    boundary-layer flow with gas injection 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S) 5d. PROJECT NUMBER Alexander V. Fedorov ...distribution unlimited Stability analysis of high-speed boundary-layer flow with gas injection Alexander V. Fedorov * and Vitaly G. Soudakov...Laminar Flow, AGARD Report Number 709, 1984. 2. Fedorov , A., “Transition and Stability of High-Speed Boundary Layers,” Annu. Rev. Fluid Mech., Vol

  4. Cross-flow analysis of injection wells in a multilayered reservoir

    OpenAIRE

    Jalali, Mohammadreza; Embry, Jean-Michel; Sanfilippo, Francesco; Santarelli, Frederic J.; Maurice B. Dusseault

    2016-01-01

    During fluid injection into a multilayered reservoir, a different pressure gradient is generated across the face of each permeable layer. This pressure gradient generates driving forces in the wellbore during well shut-in that causes the injected fluid moves from higher pressure layers to lower pressure layers, a phenomenon known as interwell cross-flow. Cross-flow behavior depends on the initial pressure in the permeable layers and may be referred to as natural cross-flow (identical or natur...

  5. Investigation of the Effect of Pipeline Size on the Cross Flow Injection Process

    Directory of Open Access Journals (Sweden)

    M. Elashmawy

    2016-06-01

    Full Text Available Injection pumps constitute an essential component for many industrial applications. The main focus of this study is to predict the effect of the size of the pipeline on the cross flow injection process. A test-rig was designed, built and equipped with three different pipelines, 1½", ¾" and ½" diameters. Comparison was made under constant line pressure of 40-bar and line flow rate of 5 liter/min, with a fixed injection pump rotational speed of 100 rpm. The main parameter tested was the injection dose capacity at different pump displacements. Cross flow mixing process is also theoretically studied using 3D-CFD analysis to show the injection cross flow behavior for the same geometry and parameters used for experimental test. Results show that increasing the size of the pipeline increases injection pump doses ability. This effect is insignificant at lower injection pump displacements, while the effect of the size of the pipeline becomes dominant when increasing the displacement. By changing the size of the pipeline from ½" to 1½" diameter injection pump dose capacity increases by 3.24% at 100% pump displacement. Selecting larger pipe sizes for injection ports is recommended whenever possible.

  6. Combination of Flow Injection and Electrothermal Atomic Absorption Spectrometry

    DEFF Research Database (Denmark)

    Hansen, Elo Harald; Nielsen, Steffen

    1999-01-01

    The paper discusses the advantages gained by exploiting this combination, FI-ETAAS. Emphasis is placed on illlustrating various avenues to perform on-line preconcentration of metal ions in order to obtain very low limits of detection of the measurand, and ways and means to enhance the selectivity...

  7. Trends and perspectives of flow injection/sequential injection on-line sample-pretreatment schemes coupled to ETAAS

    DEFF Research Database (Denmark)

    Wang, Jianhua; Hansen, Elo Harald

    2005-01-01

    Flow injection (FI) analysis, the first generation of this technique, became in the 1990s supplemented by its second generation, sequential injection (SI), and most recently by the third generation (i.e.,Lab-on-Valve). The dominant role played by FI in automatic, on-line, sample pretreatments in ......-review is thus to illustrate the state-of-the-art progress in implementing miniaturised FI/SI systems for on-line separation and preconcentration of trace metals with detection by ETAAS since 2000. We also discuss future perspectives in this field....

  8. Differentiating organic and conventional sage by chromatographic and mass spectrometry flow-injection fingerprints

    Science.gov (United States)

    High performance liquid chromatography (UPLC) and flow injection electrospray ionization with ion trap mass spectrometry (FIMS) fingerprints combined with the principal component analysis (PCA) were examined for their potential in differentiating commercial organic and conventional sage samples. The...

  9. Injection molded pinched flow fractionation device for enrichment of somatic cells in cow milk

    DEFF Research Database (Denmark)

    Jensen, Marie Pødenphant; Marie, Rodolphe; Olesen, Tom

    2014-01-01

    . The enrichment was performed using an all-polymer pinched flow fractionation device fabricated by injection molding. The polymer chips were bonded to a 500 lm polymer foil using UV assisted thermal bonding. The quality of the final devices was reproducible and the injection molding process combined with the use...

  10. Impulse/response functions of individual components of flow-injection manifolds

    NARCIS (Netherlands)

    van Nugteren-Osinga, I.C.; Bos, M.; van der Linden, W.E.

    1988-01-01

    The dispersion behaviour of the various individual parts making up a flow-injection manifold is often difficult to establish because it is virtually impossible to obtainthe required very small injection and detection volumes. It is shown that it is possible, under suitable experimental conditions,

  11. The potentials of the third generation of flow injection analysis for nutrient monitoring and fractionation analysis

    DEFF Research Database (Denmark)

    Miró, Manuel; Hansen, Elo Harald; Buanuam, Janya

    2006-01-01

    In the present communication, the third generation of flow injection analysis, the so-called micro sequential-injection Laboratory-on-Valve (μSI-LOV), is presented as a miniaturized, automated approach for on-line monitoring of nutrients in different environmental compartments as effected under e...

  12. Injection of Drag Reducing Additives Into Turbulent Water Flows: Results from Factorial Design

    Science.gov (United States)

    1984-04-01

    with edditive Injection was measured. The injection was then terminated and the "without- injsction" pressure drop was reoeitured. Finally the flow...result is of prime impetance in the optimization proceoe . Since the purpose of this studl Is to mazimie the drag- reducing performance of the

  13. Stability Analysis of High-Speed Boundary-Layer Flow with Gas Injection (Briefing Charts)

    Science.gov (United States)

    2014-06-01

    boundary-layer flow with gas injection 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S) 5d. PROJECT NUMBER Alexander V. Fedorov ...Release; Distribution Unlimited Stability analysis of high-speed boundary-layer flow with gas injection Alexander Fedorov and Vitaly Soudakov Moscow...Dispersion relation from WKB analysis*,**: *Guschin, V.R., & Fedorov , A.V., Fluid Dynamics, Vol. 24, No.1, 1989 **Guschin, V.R., & Fedorov , A.V., NASA

  14. Air Flow and Gassing Potential in Micro-injection Moulding

    DEFF Research Database (Denmark)

    Griffithsa, C.A.; Dimova, S.S.; Scholz, S.

    2011-01-01

    Process monitoring of micro injection moulding (μ-IM) is of crucial importance in understanding the effects of different parameter settings on the process, especially on its performance and consistency in regards to parts’ quality. Quality factors related to mould cavity air evacuation can provid...

  15. Flow Injection/Sequential Injection Analysis Systems: Potential Use as Tools for Rapid Liver Diseases Biomarker Study

    Directory of Open Access Journals (Sweden)

    Supaporn Kradtap Hartwell

    2012-01-01

    Full Text Available Flow injection/sequential injection analysis (FIA/SIA systems are suitable for carrying out automatic wet chemical/biochemical reactions with reduced volume and time consumption. Various parts of the system such as pump, valve, and reactor may be built or adapted from available materials. Therefore the systems can be at lower cost as compared to other instrumentation-based analysis systems. Their applications for determination of biomarkers for liver diseases have been demonstrated in various formats of operation but only a few and limited types of biomarkers have been used as model analytes. This paper summarizes these applications for different types of reactions as a guide for using flow-based systems in more biomarker and/or multibiomarker studies.

  16. Modification of toroidal flow velocity through momentum Injection by compact torus injection into the STOR-M tokamak

    Science.gov (United States)

    Rohollahi, A.; Elgriw, S.; Basu, D.; Wolfe, S.; Hirose, A.; Xiao, C.

    2017-05-01

    In the Saskatchewan torus-modified (STOR-M) tokamak, tangential compact torus injection (CTI) experiments have been performed with normal (counter-clockwise, CCW, top view) and reversed (clockwise, CW, top view) plasma current directions while the compact torus (CT) injection direction remains in the CCW direction. The intrinsic toroidal flow direction reverses when the discharge current is reversed. However, the change in the toroidal flow direction is always toward the CTI direction (CCW). It has been determined that the momentum in high density and high velocity CT is more than ten times larger than the intrinsic toroidal rotation momentum in the typical STOR-M plasma. Therefore, the modification of the plasma toroidal rotation velocity is attributed to momentum transfer from CT to the tokamak discharge.

  17. Gold nanorods for surface Plasmon resonance detection of mercury (II) in flow injection analysis.

    Science.gov (United States)

    Trieu, Khang; Heider, Emily C; Brooks, Scott C; Barbosa, Fernando; Campiglia, Andres D

    2014-10-01

    This article investigates the flow injection analysis of mercury (II) ions in tap water samples via surface Plasmon resonance detection. Quantitative analysis of mercury (II) is based on the chemical interaction of metallic mercury with gold nanorods immobilized on a glass substrate. A new flow cell design is presented with the ability to accommodate the detecting substrate in the sample compartment of commercial spectrometers. Two alternatives are here considered for mercury (II) detection, namely stop-flow and continuous flow injection analysis modes. The best limit of detection (2.4 ng mL(-1)) was obtained with the continuous flow injection analysis approach. The accurate determination of mercury (II) ions in samples of unknown composition is demonstrated with a fortified tap water sample. Copyright © 2014 Elsevier B.V. All rights reserved.

  18. Coupling on-line preconcentration by ion-exchange with ETAAS. A novel flow injection approach based on the use of a renewable microcolumn as demonstrated for the determination of nickel in environmental and biological samples

    DEFF Research Database (Denmark)

    Wang, Jianhua; Hansen, Elo Harald

    2000-01-01

    A novel way of exploiting flow injection/sequential injection (FIA/SIA) on-line ion-exchange preconcentration with detection by electrothermal atomic absorption spectrometry (ETAAS) is described and demonstrated for the determination of trace-levels of nickel. Based on the use of a renewable micr...... was validated by determination of the nickel contents in two certified reference materials and in a human urine sample. (C) 2000 Elsevier Science B.V. All rights reserved.......A novel way of exploiting flow injection/sequential injection (FIA/SIA) on-line ion-exchange preconcentration with detection by electrothermal atomic absorption spectrometry (ETAAS) is described and demonstrated for the determination of trace-levels of nickel. Based on the use of a renewable...

  19. Effects of compact torus injection on toroidal flow in the STOR-M tokamak

    Science.gov (United States)

    Onchi, T.; Liu, Y.; Dreval, M.; McColl, D.; Elgriw, S.; Liu, D.; Asai, T.; Xiao, C.; Hirose, A.

    2013-03-01

    In compact torus injection (CTI) experiments on the STOR-M tokamak, an ion Doppler spectrometer is installed to observe the effects of CTI on toroidal plasma flows. The intrinsic toroidal flow in ohmic discharges without CTI is sheared with counter plasma current flow in the core region and co-current direction at the periphery. With tangential CTI along the co-current direction, the flow velocity in the core region decreases by more than 5 km s-1, while in the periphery the flow velocity increases by 3-4 km s-1. These data indicate that the observed flow change is due to the injection of toroidal momentum. Density increase and high soft x-ray emission after CTI are observed during the changes in the toroidal flow.

  20. Flow visualization of lateral jet injection into swirling crossflow

    Science.gov (United States)

    Ferrell, G. B.; Aoki, K.; Lilley, D. G.

    1985-01-01

    Flow visualization experiments have been conducted to characterize the time-mean flowfield of a deflected turbulent jet in a confining cylindrical crossflow. Jet-to-crossflow velocity ratios of 2, 4, and 6 were investigated, under crossflow inlet swirler vane angles of 0 (swirler removed), 45 and 70 degrees. Smoke, neutrally-buoyant helium-filled soap bubbles, and multi-spark flow visualization were employed to highlight interesting features of the deflected jet, as well as the trajectory and spread pattern of the jet. Gross flowfield characterization was obtained for a range of lateral jet-to-crossflow velocity ratios and a range of inlet swirl strengths in the main flow. The flow visualization results agree well with the measurements obtained elsewhere with the six-orientation single hot-wire method.

  1. EU Enlargement: Migration flows from Central and Eastern Europe into the Nordic countries - exploiting a natural experiment

    DEFF Research Database (Denmark)

    Pedersen, Peder J.; Pytlikova, Mariola

    In this paper we look at migration flows from 10 Central and Eastern European Countries (CEEC) to 5 Nordic countries over the years 1985 - 2007. We exploit a natural experiment that arose from the fact that while Sweden opened its labour market from the day one of the 2004 EU enlargement...... of the "EU entry" on migration. Therefore we look at migration flows from CEECs during the first round of EU enlargement towards the East in 2004 and compare them with migration flows from Bulgaria and Romania. The estimated effect from our D-in-D analyses is positive and significant in all model......, and Finland and Iceland from year 2006, the other Nordic countries chose a transition period in relation to the "new" EU members. The results based on a differences-in-differences estimator show that the estimated effect of the opening of the Swedish, Finnish and Icelandic labour markets on migration from...

  2. EU Enlargement: Migration flows from Central and Eastern Europe into the Nordic countries - exploiting a natural experiment

    DEFF Research Database (Denmark)

    Pytlikova, Mariola; Pedersen, Peder J.

    We look at migration flows from 8 Central and Eastern European Countries (CEECs) to 5 Nordic countries over the years 1985 - 2005 and we can exploit a natural experiment that arose from the fact that while Sweden opened its labour market from the day one of the 2004 EU enlargement, the other Nordic...... are interested in the overall effect of the "EU entry" on migration. Therefore we look at migration flows from CEECs during the first round EU enlargement towards CEECs in 2004 and compare them with migration flows from Bulgaria and Romania. We again used a DD estimator in our analysis. The estimated effect...... countries chose a transition period in relation to the "new" EU members. We employ a differences-in-differences estimator in our analysis. The results show that the estimated effect of the opening of Swedish labour market in 2004 on migration is insignificantly different from zero. Further, we...

  3. An experimental study of wall-injected flows in a rectangular cylinder

    Science.gov (United States)

    Perrotta, A.; Romano, G. P.; Favini, B.

    2018-01-01

    An experimental investigation of the flow inside a rectangular cylinder with air injected continuously along the wall is performed. This kind of flow is a two-dimensional approximation of what happens inside a solid rocket motor, where the lateral grain burns expelling exhaust gas or in processes with air filtration or devices to attain uniform flows. We propose a brief derivation of some analytical solutions and a comparison between these solutions and experimental data, which are obtained using the particle image velocimetry technique, to provide a global reconstruction of the flowfield. The flow, which enters orthogonal to the injecting wall, turns suddenly its direction being pushed towards the exit of the chamber. Under the incompressible and inviscid flow hypothesis, two analytical solutions are reported and compared. The first one, known as Hart-McClure solution, is irrotational and the injection velocity is non-perpendicular to the injecting wall. The other one, due to Taylor and Culick, has non-zero vorticity and constant, vertical injection velocity. The comparison with laminar solutions is useful to assess whether transition to turbulence is reached and how the disturbance thrown in by the porous injection influences and modifies those solutions.

  4. Exploiting LSPIV to assess debris-flow velocities in the field

    Directory of Open Access Journals (Sweden)

    J. I. Theule

    2018-01-01

    Full Text Available The assessment of flow velocity has a central role in quantitative analysis of debris flows, both for the characterization of the phenomenology of these processes and for the assessment of related hazards. Large-scale particle image velocimetry (LSPIV can contribute to the assessment of surface velocity of debris flows, provided that the specific features of these processes (e.g. fast stage variations and particles up to boulder size on the flow surface are taken into account. Three debris-flow events, each of them consisting of several surges featuring different sediment concentrations, flow stages, and velocities, have been analysed at the inlet of a sediment trap in a stream in the eastern Italian Alps (Gadria Creek. Free software has been employed for preliminary treatment (orthorectification and format conversion of video-recorded images as well as for LSPIV application. Results show that LSPIV velocities are consistent with manual measurements of the orthorectified imagery and with front velocity measured from the hydrographs in a channel recorded approximately 70 m upstream of the sediment trap. Horizontal turbulence, computed as the standard deviation of the flow directions at a given cross section for a given surge, proved to be correlated with surface velocity and with visually estimated sediment concentration. The study demonstrates the effectiveness of LSPIV in the assessment of surface velocity of debris flows and permit the most crucial aspects to be identified in order to improve the accuracy of debris-flow velocity measurements.

  5. Exploiting LSPIV to assess debris-flow velocities in the field

    Science.gov (United States)

    Theule, Joshua I.; Crema, Stefano; Marchi, Lorenzo; Cavalli, Marco; Comiti, Francesco

    2018-01-01

    The assessment of flow velocity has a central role in quantitative analysis of debris flows, both for the characterization of the phenomenology of these processes and for the assessment of related hazards. Large-scale particle image velocimetry (LSPIV) can contribute to the assessment of surface velocity of debris flows, provided that the specific features of these processes (e.g. fast stage variations and particles up to boulder size on the flow surface) are taken into account. Three debris-flow events, each of them consisting of several surges featuring different sediment concentrations, flow stages, and velocities, have been analysed at the inlet of a sediment trap in a stream in the eastern Italian Alps (Gadria Creek). Free software has been employed for preliminary treatment (orthorectification and format conversion) of video-recorded images as well as for LSPIV application. Results show that LSPIV velocities are consistent with manual measurements of the orthorectified imagery and with front velocity measured from the hydrographs in a channel recorded approximately 70 m upstream of the sediment trap. Horizontal turbulence, computed as the standard deviation of the flow directions at a given cross section for a given surge, proved to be correlated with surface velocity and with visually estimated sediment concentration. The study demonstrates the effectiveness of LSPIV in the assessment of surface velocity of debris flows and permit the most crucial aspects to be identified in order to improve the accuracy of debris-flow velocity measurements.

  6. Mathematical modelling of a flow-injection system with a membrane separation module

    NARCIS (Netherlands)

    Kolev, S.D.; Kolev, Spas D.; van der Linden, W.E.

    1992-01-01

    A mathematical model for a flow-injection system with a membrane separation module based on the axially dispersed plug flow model was developed. It takes into account the geometrical dimensions and dispersion properties of the main sections of the manifold, the mass transfer in the channels of the

  7. Automated stand-alone flow injection immunoanalysis system for the determination of cephalexin in milk

    NARCIS (Netherlands)

    Meyer, U.J.; Zhi, Z.L.; Loomans, E.; Spener, F.; Meusel, F.

    1999-01-01

    A fully automated stand-alone flow injection immunoanalysis (FIIA) device for the determination of cephalexin in milk is developed with a main focus on the investigation of the influence of the sample matrix. The system is based on principles of flow-through immunoassays and on sequential addition

  8. Flow-injection amperometric glucose biosensors based on graphene/Nafion hybrid electrodes

    Energy Technology Data Exchange (ETDEWEB)

    Choi, Bong Gill, E-mail: k1811@kaist.ac.kr [Department of Chemical and Biomolecular Engineering (BK21 Program), KAIST, Daejeon 305-701 (Korea, Republic of); Im, Jinkyu, E-mail: JINQ@paran.com [Department of Chemistry and Research Institute of Basic Sciences, Kyung Hee University, 1 Hoegidong, Dongdamoongu, Seoul (Korea, Republic of); Kim, Hoon Sik, E-mail: khs2004@khu.ac.kr [Department of Chemistry and Research Institute of Basic Sciences, Kyung Hee University, 1 Hoegidong, Dongdamoongu, Seoul (Korea, Republic of); Park, HoSeok, E-mail: phs0727@khu.ac.kr [Department of Chemical Engineering, College of Engineering, Kyung Hee University, 1 Seochon-dong, Giheung-gu, Youngin-si, Gyeonggi-do 446-701 (Korea, Republic of)

    2011-11-30

    Graphical abstract: Amperometric biosensors based on graphene hybrids showed the fast, sensitive, and stable amperometric responses in the flow injection system for automatically monitoring glucose. Display Omitted Highlights: > Flow-injection amperometric glucose biosensors were fabricated using reduced graphene oxide/Nafion hybrids. > The electrochemical kinetics of biosensors were comprehensively investigated by analysing electron transfer rate, charge transfer resistance, and ion diffusion coefficient, respectively. > The biosensors exhibited the fast, sensitive, and stable amperometric responses in the flow injection system for detecting glucose. - Abstract: In this research, we demonstrated the fabrication of flow-injection amperometric glucose biosensors based on RGO/Nafion hybrids. The nanohybridization of the reduced graphene oxide (RGO) by Nafion provided the fast electron transfer (ET) for the sensitive amperometric biosensor platforms. The ET rate (k{sub s}) and the charge transfer resistance (R{sub CT}) of GOx-RGO/Nafion hybrids were evaluated to verify the accelerated ET. Moreover, hybrid biosensors revealed a quasi-reversible and surface controlled process, as confirmed by the low peak-to-peak ({Delta}E{sub p}) and linear relations between I{sub p} and scan rate ({nu}). Hybrid biosensors showed the fast response time of {approx}3 s, the sensitivity of 3.8 {mu}A mM{sup -1} cm{sup -2}, the limit of detection of 170 {mu}M, and the linear detection range of 2-20 mM for the flow-injection amperometric detection of glucose. Furthermore, interference effect of oxidizable species such as ascorbic acid (AA) and uric acid (UA) on the performance of hybrid biosensors was prevented at the operating potential of -0.20 V even under the flow injection mode. Therefore, the fast, sensitive, and stable amperometric responses of hybrid biosensors in the flow injection system make it highly suitable for automatically monitoring glucose.

  9. Investigation on the achievable flow length in injection moulding of polymeric materials with dynamic mould tempering.

    Science.gov (United States)

    Meister, Steve; Drummer, Dietmar

    2013-01-01

    A variety of parts in microsystems technology are manufactured by injection moulding of polymeric materials. In Particular the high cooling velocity affects negatively the process and the resulting part properties. The scope of this paper is to investigate the influence on the reachable flow length in injection moulding of different polymeric materials. The results indicate that the mould temperature has less impact on the achievable flow length of the polymer melt as the injection pressure. A higher mould temperature leads only to a slight increase in flow length. In addition, a transcending of the glass or the crystallization temperature of polymeric materials with the mould temperature shows no effect on the achievable flow length of the material.

  10. Investigation on the Achievable Flow Length in Injection Moulding of Polymeric Materials with Dynamic Mould Tempering

    Directory of Open Access Journals (Sweden)

    Steve Meister

    2013-01-01

    Full Text Available A variety of parts in microsystems technology are manufactured by injection moulding of polymeric materials. In Particular the high cooling velocity affects negatively the process and the resulting part properties. The scope of this paper is to investigate the influence on the reachable flow length in injection moulding of different polymeric materials. The results indicate that the mould temperature has less impact on the achievable flow length of the polymer melt as the injection pressure. A higher mould temperature leads only to a slight increase in flow length. In addition, a transcending of the glass or the crystallization temperature of polymeric materials with the mould temperature shows no effect on the achievable flow length of the material.

  11. TOUGH2-seed: A coupled fluid flow and mechanical-stochastic approach to model injection-induced seismicity

    Science.gov (United States)

    Rinaldi, Antonio P.; Nespoli, Massimo

    2017-11-01

    Understanding the injection-induced triggering mechanism is a fundamental step towards controlling the seismicity generated by deep underground exploitation. Here we propose a modeling approach based on coupling the TOUGH2 simulator with a geomechanical-stochastic model. The hydro-mechanical-stochastic model provides a good representation of different mechanisms influencing each other during and after the injection phase. Each mechanism affects the induced seismicity in a different way and at different times during the reservoir stimulation, confirming that a complex interaction is in place, and that more sophisticated and physics-based approaches coupled with statistical model are required to explain such a complex interaction. In addition to previous statistical and hybrid models, our approach accounts for a full 3D formulation of both stresses and fluid flow, further including all the TOUGH2 capabilities. Furthermore, it includes interactions between triggered seismic events through calculation of static stress transfer. In this work, we present the main capabilities of TOUGH2-SEED and apply the model to the Basel EGS case, successfully reproducing the injection pressure as well as the evolution of the seismicity.

  12. Flow field development in a direct injection diesel engine with ...

    African Journals Online (AJOL)

    The flow characteristics of these engine manifolds are examined under transient conditions using Computational Fluid Dynamics (CFD) code STAR-CD. The predicted CFD results of mean swirl velocity of the engine at different locations inside the combustion chamber at the end of compression stroke are compared with ...

  13. A membraneless gas-diffusion unit-multisyringe flow injection spectrophotometric method for ammonium determination in untreated environmental samples.

    Science.gov (United States)

    Almeida, M Inês G S; Estela, José Manuel; Segundo, Marcela A; Cerdà, Víctor

    2011-06-15

    A new design of a membraneless gas-diffusion (MGD) unit coupled to a multisyringe flow injection system is proposed. The spectrophotometric determination of ammonium using an acid-base indicator was chosen to show the feasibility of this approach. Hence, in alkaline medium, ammonium ions are transformed into ammonia (donor channel) which diffuses through the headspace into the acceptor stream (bromothymol blue solution), causing a pH change and subsequently a colour change. The exploitation of the enhanced potentialities of this re-designed MGD device was the main purpose of the present work. Hence, several strategies concerning flow management were studied seeking to characterize and improve the analytical features of the methodology and moreover, untreated environmental samples were analysed without previous filtration. Consequently, stopped flow in acceptor channel with continuous flow in donor channel was chosen for the application to wastewater and spiked river water samples. A linear concentration range between 10.0 and 50.0 mg L(-1) of NH(4)(+), a limit of detection of 2.20 mg L(-1) and a determination frequency of 11h(-1) were obtained. Copyright © 2011 Elsevier B.V. All rights reserved.

  14. Cross-flow analysis of injection wells in a multilayered reservoir

    Directory of Open Access Journals (Sweden)

    Mohammadreza Jalali

    2016-09-01

    Natural and forced cross-flow is modeled for some injection wells in an oil reservoir located at North Sea. The solution uses a transient implicit finite difference approach for multiple sand layers with different permeabilities separated by impermeable shale layers. Natural and forced cross-flow rates for each reservoir layer during shut-in are calculated and compared with different production logging tool (PLT measurements. It appears that forced cross-flow is usually more prolonged and subject to a higher flow rate when compared with natural cross-flow, and is thus worthy of more detailed analysis.

  15. Flow Injection and Atomic Absorption Spectrometry (FI-AAS) -

    DEFF Research Database (Denmark)

    Hansen, Elo Harald

    1996-01-01

    absorption spectrometry (AAS). Initially with flame-AAS (fAAS) procedures, later for hydride generation (HG) techniques, and most recently in combination with electrothermal AAS (ETAAS). The common denominator for all these procedures is the inherently precise and strictly reproducible timing in FI from...... the point of sample injection/introduction to the point of detection. Hence, in FI-fAAS this feature allows not only to obtain improved repeatability but also improved accuracy, and because the wash to sample ratio is high it permits the handling of samples with elevated salt contents - which...... of (especially HG- forming) elements. In the words of the one of the authorities of AAS and foremost pioneers of FI-AAS - Professor Z. L. Fang, who is the author on two recently published monographs on this hyphenated technique - the impact of FI on AAS is "so dramatic" that it has brought "new vitality...

  16. Magnetized plasma flow injection into tokamak and high-beta compact torus plasmas

    Science.gov (United States)

    Matsunaga, Hiroyuki; Komoriya, Yuuki; Tazawa, Hiroyasu; Asai, Tomohiko; Takahashi, Tsutomu; Steinhauer, Loren; Itagaki, Hirotomo; Onchi, Takumi; Hirose, Akira

    2010-11-01

    As an application of a magnetized coaxial plasma gun (MCPG), magnetic helicity injection via injection of a highly elongated compact torus (magnetized plasma flow: MPF) has been conducted on both tokamak and field-reversed configuration (FRC) plasmas. The injected plasmoid has significant amounts of helicity and particle contents and has been proposed as a fueling and a current drive method for various torus systems. In the FRC, MPF is expected to generate partially spherical tokamak like FRC equilibrium by injecting a significant amount of magnetic helicity. As a circumstantial evidence of the modified equilibrium, suppressed rotational instability with toroidal mode number n = 2. MPF injection experiments have also been applied to the STOR-M tokamak as a start-up and current drive method. Differences in the responses of targets especially relation with beta value and the self-organization feature will be studied.

  17. Andreas Acrivos Dissertation Prize Lecture: Stability of inviscid flows from bifurcation diagrams exploiting a variational argument

    Science.gov (United States)

    Luzzatto-Fegiz, Paolo

    2011-11-01

    Steady fluid solutions play a special role in the dynamics of a flow: stable states may be realized in practice, while unstable ones may act as attractors. Unfortunately, determining stability is often a process far more laborious than finding steady states; indeed, even for simple vortex or wave flows, stability properties have often been the subject of debate. We consider here a stability idea originating with Lord Kelvin (1876), which involves using the second variation of the energy, δ2 E , to establish bounds on a perturbation. However, for numerically obtained flows, computing δ2 E explicitly is often not feasible. To circumvent this issue, Saffman & Szeto (1980) proposed an argument linking changes in δ2 E to turning points in a bifurcation diagram, for families of steady flows. Later work has shown that this argument is unreliable; the two key issues are associated with the absence of a formal turning-point theory, and with the inability to detect bifurcations (Dritschel 1995, and references therein). In this work, we build on ideas from bifurcation theory, and link turning points in a velocity-impulse diagram to changes in δ2 E ; in addition, this diagram delivers the direction of the change of δ2 E , thereby providing information as to whether stability is gained or lost. To detect hidden solution branches, we introduce to these fluid problems concepts from imperfection theory. The resulting approach, involving ``imperfect velocity-impulse'' diagrams, leads us to new and surprising results for a wide range of fundamental vortex and wave flows; we mention here the calculation of the first steady vortices without any symmetry, and the uncovering of the complete solution structure for vortex pairs. In addition, we find precise agreement with available results from linear stability analysis. Doctoral work advised by C.H.K. Williamson at Cornell University.

  18. Numerical Simulation of Polymer Injection in Turbulent Flow Past a Circular Cylinder

    KAUST Repository

    Richter, David

    2011-01-01

    Using a code developed to compute high Reynolds number viscoelastic flows, polymer injection from the upstream stagnation point of a circular cylinder is modeled at Re = 3900. Polymer stresses are represented using the FENE-P constitutive equations. By increasing polymer injection rates within realistic ranges, significant near wake stabilization is observed. Rather than a turbulent detached shear layer giving way to a chaotic primary vortex (as seen in Newtonian flows at high Re), a much more coherent primary vortex is shed, which possesses an increased core pressure as well as a reduced level of turbulent energy. © 2011 American Society of Mechanical Engineers.

  19. Theoretical Study on the Flow of Refilling Stage in a Safety Injection Tank

    Energy Technology Data Exchange (ETDEWEB)

    Park, Jun Sang [Halla Univ. Daejeon (Korea, Republic of)

    2017-10-15

    In this study, a theoretical analysis was performed to the flow of refilling stage in a safety injection tank, which is the core cooling system of nuclear power plant in an emergency. A theoretical model was proposed with a nonlinear governing equation defining on the flow of the refilling process of the coolant. Utilizing the Taylor-series expansion, the 1st - order approximation flow equation was obtained, along with its analytic solution of closed type, which could predict accurately the variations of free surface height and flow rate of the coolant. The availability of theoretical result was confirmed by comparing with previous experimental results.

  20. The effects of arbitrary injection angle and flow conditions on venturi-jet mixer

    Directory of Open Access Journals (Sweden)

    Sundararaj S.

    2012-01-01

    Full Text Available This paper describes the effect of jet injection angle, cross flow Reynolds number and velocity ratio on entrainment and mixing of jet with incompressible cross flow in venturi-jet mixer. Five different jet injection angles 45o, 60o, 90o, 125o, 135o are tested to evaluate the entrainment of jet and mixing performances of the mixer. Tracer concentration along the downstream of the jet injection, cross flow velocity, jet velocity and pressure drop across the mixer are determined experimentally to characterize the mixing performance of the mixer. The experiments show that the performance of a venturi-jet-mixer substantially improves at high injection angle and can be augmented still by increasing velocity ratio. The jet deflects much and penetrates less in the cross flow as the cross flow Reynolds number is increased. The effect could contribute substantially to the better mixing index with moderate pressure drop. Normalized jet profile, concentration decay, jet velocity profile are computed from equations of conservation of mass, momentum and concentration written in natural co-ordinate systems. The comparison between the experimental and numerical results confirms the accuracy of the simulations. Correlations for jet trajectory and entrainment ratio of the mixer are obtained by multivariate-linear regression analysis using power law.

  1. Exploiting Satellite Focal Plane Geometry for Automatic Extraction of Traffic Flow from Single Optical Satellite Imagery

    Science.gov (United States)

    Krauß, T.

    2014-11-01

    The focal plane assembly of most pushbroom scanner satellites is built up in a way that different multispectral or multispectral and panchromatic bands are not all acquired exactly at the same time. This effect is due to offsets of some millimeters of the CCD-lines in the focal plane. Exploiting this special configuration allows the detection of objects moving during this small time span. In this paper we present a method for automatic detection and extraction of moving objects - mainly traffic - from single very high resolution optical satellite imagery of different sensors. The sensors investigated are WorldView-2, RapidEye, Pléiades and also the new SkyBox satellites. Different sensors require different approaches for detecting moving objects. Since the objects are mapped on different positions only in different spectral bands also the change of spectral properties have to be taken into account. In case the main distance in the focal plane is between the multispectral and the panchromatic CCD-line like for Pléiades an approach for weighted integration to receive mostly identical images is investigated. Other approaches for RapidEye and WorldView-2 are also shown. From these intermediate bands difference images are calculated and a method for detecting the moving objects from these difference images is proposed. Based on these presented methods images from different sensors are processed and the results are assessed for detection quality - how many moving objects can be detected, how many are missed - and accuracy - how accurate is the derived speed and size of the objects. Finally the results are discussed and an outlook for possible improvements towards operational processing is presented.

  2. Measuring and modelling air mass flow rate in the injection stretch blow moulding process

    OpenAIRE

    Salomeia, Y.; Menary, G. H.; Armstrong, C G; Nixon, J; S. Yan

    2016-01-01

    The injection stretch blow moulding process involves the inflation and stretching of a hot preform into a mould to form bottles. A critical process variable and an essential input for process simulations is the rate of pressure increase within the preform during forming, which is regulated by an air flow restrictor valve. The paper describes a set of experiments for measuring the air flow rate within an industrial ISBM machine and the subsequent modelling of it with the FEA package ABAQUS. Tw...

  3. DIFFERENTIAL CONDUCTIMETRY IN FLOW-INJECTION - DETERMINATION OF AMMONIA IN KJELDAHL DIGESTS

    OpenAIRE

    Rohwedder J.J.R.; Pasquini C.

    1991-01-01

    A differential conductivity meter has been constructed for use in flow injection (Fl) systems. The instrument employs a Wien bridge to generate a sinusoidal alternating electrical potential (2 V, 1.4 kHz) applied to a measurement bridge containing two twin conductance flow cells. The difference in the conductance between the cells is monitored. The instrument can be used to follow the small changes in conductance that occur in samples in which a high background ionic concentration is found. T...

  4. Active control of flow around a square prism by slot jet injection

    Directory of Open Access Journals (Sweden)

    Hacıalioğulları M.

    2013-04-01

    Full Text Available The main aim of the experimental study is to determine both the most effective injection surface and rate in order to ensure minimum drag and fluctuating forces on a square prism subjected to crossflow. All predetermined jet injection surfaces i.e. front, side, and rear, tested separately for injection ratios of IR = 0, 1, 1.5, 2 at Reynolds number of Re = 16,000. Surface pressures were measured by differential pressure transducer whereas instantaneous velocity measurements were performed by using multichannel Constant Temperature Anemometer (CTA. It was concluded that jet injection, especially from the rear surface, brought noticeable improvements to the flow characteristics of a square prism. For rear jet configuration with IR = 1.5, the mean drag coefficient (CDT¯$overline {{C_{{m{DT}}}}} $ was reduced to 79.4% and CP RMS level on side surfaces was reduced to 20% of that of the single square prism. In addition, instantaneous flow visualization photographs and Strouhal number (St distribution across the injection ratio were also presented to identify the flow patterns and underlying mechanism of drag and fluctuating force reduction of square prism with rear jet configuration.

  5. Benchmark initiative on coupled multiphase flow and geomechanical processes during CO2 injection

    Science.gov (United States)

    Benisch, K.; Annewandter, R.; Olden, P.; Mackay, E.; Bauer, S.; Geiger, S.

    2012-12-01

    CO2 injection into deep saline aquifers involves multiple strongly interacting processes such as multiphase flow and geomechanical deformation, which threat to the seal integrity of CO2 repositories. Coupled simulation codes are required to establish realistic prognoses of the coupled process during CO2 injection operations. International benchmark initiatives help to evaluate, to compare and to validate coupled simulation results. However, there is no published code comparison study so far focusing on the impact of coupled multiphase flow and geomechanics on the long-term integrity of repositories, which is required to obtain confidence in the predictive capabilities of reservoir simulators. We address this gap by proposing a benchmark study. A wide participation from academic and industrial institutions is sought, as the aim of building confidence in coupled simulators become more plausible with many participants. Most published benchmark studies on coupled multiphase flow and geomechanical processes have been performed within the field of nuclear waste disposal (e.g. the DECOVALEX project), using single-phase formulation only. As regards CO2 injection scenarios, international benchmark studies have been published comparing isothermal and non-isothermal multiphase flow processes such as the code intercomparison by LBNL, the Stuttgart Benchmark study, the CLEAN benchmark approach and other initiatives. Recently, several codes have been developed or extended to simulate the coupling of hydraulic and geomechanical processes (OpenGeoSys, ELIPSE-Visage, GEM, DuMuX and others), which now enables a comprehensive code comparison. We propose four benchmark tests of increasing complexity, addressing the coupling between multiphase flow and geomechanical processes during CO2 injection. In the first case, a horizontal non-faulted 2D model consisting of one reservoir and one cap rock is considered, focusing on stress and strain regime changes in the storage formation and the

  6. Exploiting gas diffusion for non-invasive sampling in flow analysis: determination of ethanol in alcoholic beverages.

    Science.gov (United States)

    Vicente, Simone; Zagatto, Elias A G; Pinto, Paula C A G; Saraiva, Maria Lucia M E S; Lima, José L F C; Borges, Eduardo P

    2006-03-01

    A tubular gas diffusion PTFE membrane is exploited for non-invasive sampling in flow analysis, aiming to develop an improved spectrophotometric determination of ethanol in alcoholic beverages. The probe is immersed into the sample, allowing ethanol to diffuse through the membrane. It is collected into the acceptor stream (acidic dichromate solution), leading to formation of Cr(III), monitored at 600 nm. The analytical curve is linear up to 50% (v/v) ethanol, baseline drift is < 0.005 absorbance during four working-hours, and sample throughput is 30 h(-1), meaning 0.6 mmol K2Cr2O7 per determination. Results are precise (r.s.d.< 2%) and in agreement with an official procedure.

  7. Differentiating organic from conventional peppermints using chromatographic and flow-injection mass spectrometric (FIMS) fingerprints

    Science.gov (United States)

    High performance liquid chromatography (HPLC) and flow-injection mass spectrometric (FIMS) fingerprinting techniques were tested for their potential in differentiating organic and conventional peppermint samples. Ten organic and ten conventional peppermint samples were examined using HPLC-UV and FI...

  8. Flow-injection analysis of traces of lead and cadmium by solvent extraction with dithizone.

    Science.gov (United States)

    Klinghoffer, O; Růzicka, J; Hansen, E H

    1980-02-01

    An automated solvent extraction method for determination of lead and cadmium down to the 50 ng/ml level has been developed. Optimum conditions for selective and sensitive determination were designed and verified by using the flow-injection scanning method.

  9. Experimental and numerical study of tip injection in a subsonic axial flow compressor

    Directory of Open Access Journals (Sweden)

    Wei WANG

    2017-06-01

    Full Text Available Parametric study of tip injection was implemented experimentally on a subsonic axial flow compressor to understand the underlying flow mechanisms of stability improvement of the compressor with discrete tip injection. Injector throat height varied from 2 to 6 times the height of rotor tip clearance, and circumferential coverage percentage ranged from 8.3% to 25% of the annulus. Static pressure fluctuations over the rotor tip were measured with fast-response pressure transducers. Whole-passage time-accurate simulations were also carried out to help us understand the flow details. The combinations of tip injection with traditional casing treatments were experimentally studied to generate an engineering-acceptable method of compressor stall control. The results indicate that the maximum stability improvement is achieved when injectors are choked despite their different sizes. The effect of circumferential coverage percentage on compressor stability depends on the value of injector throat height for un-choked injectors, and vice versa. Tip blockage in the blade passage is greatly reduced by the choked injectors, which is the primary reason for stability enhancement. The accomplishment of blockage diminishment is maintained in the circumferential direction with the unsteady effect of tip injection, which manifests as a hysteresis between the recovery of tip blockage and the recovery of tip leakage vortex. The unsteady effect is primarily responsible for the effectiveness of tip injection with a partial circumferential coverage. Tip injection cannot enhance the stability of the rotor with axial slots significantly, but it can improve the stability of the rotor with circumferential grooves further. The combined structure of tip injection with circumferential grooves is an alternative for engineering application.

  10. A two-fluid model for vertical flow applied to CO2 injection wells

    DEFF Research Database (Denmark)

    Linga, Gaute; Lund, Halvor

    2016-01-01

    the well, including tubing, packer fluid, casing, cement or drilling mud, and rock formation. This enables prediction of the temperature in the well fluid and in each layer of the well. The model is applied to sudden shut-in and blowout cases of a CO2 injection well, where we employ the highly accurate...... to thermal stresses and subsequent loss of well integrity, and it is therefore crucial to employ models that can predict this accurately. In this work, we present a model for vertical well flow that includes both two-phase flow and heat conduction. The flow is described by a two-fluid model, where mass...

  11. Screen-printed sensor for batch and flow injection potentiometric chromium(VI) monitoring

    Energy Technology Data Exchange (ETDEWEB)

    Sanchez-Moreno, Raul A.; Gismera, M.J.; Sevilla, M.T.; Procopio, Jesus R. [Facultad de Ciencias, Universidad Autonoma de Madrid, Departamento de Quimica Analitica y Analisis Instrumental, Madrid (Spain)

    2010-05-15

    A disposable screen-printed electrode was designed and evaluated for direct detection of chromium(VI) in batch and flow analysis. The carbon screen-printed electrode was modified with a graphite-epoxy composite. The optimal graphite-epoxy matrix contains 37.5% graphite powder, 12.5% diphenylcarbohydrazide, a selective compound for chromium(VI), and 50% epoxy resin. The principal analytical parameters of the potentiometric response in batch and flow analysis were optimized and calculated. The screen-printed sensor exhibits a response time of 20 {+-} 1 s. In flow analysis, the analytical frequency of sampling is 70 injections per hour using 0.1 M NaNO{sub 3} solution at pH 3 as the carrier, a flow rate of 2.5 mL.min{sup -1}, and an injection sample volume of 0.50 mL. The sensor shows potentiometric responses that are very selective for chromium(VI) ions and optimal detection limits in both static mode (2.1 x 10{sup -7} M) and online analysis (9.4 x 10{sup -7} M). The disposable potentiometric sensor was employed to determine toxicity levels of chromium(VI) in mineral, tap, and river waters by flow-injection potentiometry and batch potentiometry. Chromium(VI) determination was also carried out with successful results in leachates from municipal solid waste landfills. (orig.)

  12. Decompositions of injection patterns for nodal flow allocation in renewable electricity networks

    Science.gov (United States)

    Schäfer, Mirko; Tranberg, Bo; Hempel, Sabrina; Schramm, Stefan; Greiner, Martin

    2017-08-01

    The large-scale integration of fluctuating renewable power generation represents a challenge to the technical and economical design of a sustainable future electricity system. In this context, the increasing significance of long-range power transmission calls for innovative methods to understand the emerging complex flow patterns and to integrate price signals about the respective infrastructure needs into the energy market design. We introduce a decomposition method of injection patterns. Contrary to standard flow tracing approaches, it provides nodal allocations of link flows and costs in electricity networks by decomposing the network injection pattern into market-inspired elementary import/export building blocks. We apply the new approach to a simplified data-driven model of a European electricity grid with a high share of renewable wind and solar power generation.

  13. Lateral Flow Aptasensor for Small Molecule Targets Exploiting Adsorption and Desorption Interactions on Gold Nanoparticles.

    Science.gov (United States)

    Alsager, Omar A; Kumar, Shalen; Hodgkiss, Justin M

    2017-07-18

    A lateral flow assay (LFA) can provide a rapid and cost-effective means to detect targets in situ; however, existing LFA formats (predominantly sandwich assays) are not suitable for small molecule targets. We present a new LFA design that probes the dissociation of aptamers from the surface of gold nanoparticles upon recognition of small targets. The target-induced removal of aptamer molecules from the surface of the colored particles results in the particles being captured on a test line comprised of the protein bovine serum albumin immobilized on nitrocellulose. On the other hand, in the absence of target, aptamer coated particles are protected from capture on the test line and are instead captured at a control line comprised of the protein lysozyme. This protein is strongly positively charged under measurement conditions and therefore captures all gold nanoparticles regardless of the presence of aptamers. The effectiveness and operation mechanism of this simply fabricated sensor was demonstrated by using a previously reported 35-mer aptamer for a small molecule, 17β-estradiol. The sensor exhibited nanomolar level of detection, excellent selectivity against potential interfering molecules, and robust operation in natural river water samples. The simplicity and performance of the sensor platform renders it applicable to a wide range of other aptamers targeting small molecules, as we demonstrated with a novel bisphenol A aptamer. Additionally, we show that our LFA design is not confined to the specific proteins used as test and control lines, provided that their charge is appropriate to modulate the interaction with aptamer-coated or bare nanoparticles.

  14. Lateral flow devices for nucleic acid analysis exploiting quantum dots as reporters

    Energy Technology Data Exchange (ETDEWEB)

    Sapountzi, Eleni A.; Tragoulias, Sotirios S.; Kalogianni, Despina P. [Department of Chemistry, University of Patras, GR-26504 Patras (Greece); Ioannou, Penelope C. [Department of Chemistry, University of Athens, GR-15771 Athens (Greece); Christopoulos, Theodore K., E-mail: tchrist@upatras.gr [Department of Chemistry, University of Patras, GR-26504 Patras (Greece); Institute of Chemical Engineering and High Temperature Processes, Foundation of Research and Technology Hellas, GR-26504 Patras (Greece)

    2015-03-15

    Highlights: • Dipstick tests for DNA hybridization assays and genotyping of single-nucleotide polymorphisms. • Use of quantum dots as reporters. • Visual detection without the need for expensive instrumentation. • Simplicity and low-cost of the assays. - Abstract: There is a growing interest in the development of biosensors in the form of simple lateral flow devices that enable visual detection of nucleic acid sequences while eliminating several steps required for pipetting, incubation and washing out the excess of reactants. In this work, we present the first dipstick-type nucleic acid biosensors based on quantum dots (QDs) as reporters. The biosensors enable sequence confirmation of the target DNA by hybridization and simple visual detection of the emitted fluorescence under a UV lamp. The ‘diagnostic’ membrane of the biosensor contains a test zone (TZ) and a control zone (CZ). The CZ always fluoresces in order to confirm the proper function of the biosensor. Fluorescence is emitted from the TZ, only when the specific nucleic acid sequence is present. We have developed two general types of QD-based nucleic acid biosensors, namely, Type I and Type II, in which the TZ consists of either immobilized streptavidin (Type I) or immobilized oligodeoxynucleotides (Type II). The control zone consists of immobilized biotinylated albumin. No purification steps are required prior to the application of the DNA sample on the strip. The QD-based nucleic acid biosensors performed accurately and reproducibly when applied to (a) the visual detection of PCR amplification products and (b) visual genotyping of single nucleotide polymorphisms (SNPs) in human genomic DNA from clinical samples. As low as 1.5 fmol of double-stranded DNA were clearly detected by naked eye and the dynamic range extended to 200 fmol. The %CV were estimated to be 4.3–8.2.

  15. Numerical simulation of turbulent flow and heat transfer in tube under injection of gas through permeable walls

    Science.gov (United States)

    Makarova, M. S.; Lushchik, V. G.

    2017-11-01

    Using a differential turbulence model, a numerical simulation of turbulent flow in a tube is carried out and the dependences of the flow and heat transfer characteristics on the intensity of the coolant injection through permeable walls are obtained. It is shown that the coefficients of friction and heat transfer decrease with increasing of injection rate. The comparison of calculation results reflecting the main features of rather complicated processes of flow in tube under gas injection with well-known experimental data over a wide range of the Reynolds number and the intensity of injection show their satisfactory agreement.

  16. Determination of cyanide in microsamples by means of capillary flow injection analysis with amperometric detection

    Energy Technology Data Exchange (ETDEWEB)

    Backofen, U. [Leipzig Univ. (Germany). Sektion 8 - Chemie; Matysik, F.-M. [Department of Chemistry, University of Coimbra (Portugal); Werner, G. [Leipzig Univ. (Germany). Sektion 8 - Chemie

    1996-10-01

    A new approach for determining cyanide in microsamples is described. The method is based on capillary flow injection analysis (CFIA) with amperometric detection. The sensing electrode is a silver-plated microdisk electrode, where cyanide can react under formation of a dicyanoargentate complex. A remarkably low mass detection limit of 231 fmol cyanide is obtained for an injection volume of 60 nl. The sample throughput of the CFIA-arrangement is comparable with a conventional sized FIA-system. A practical application is given by analyzing the cyanide (amygdalin) concentration in apple kernels. (orig.). With 5 figs.

  17. Numerical prediction of flow induced fibers orientation in injection molded polymer composites

    Science.gov (United States)

    Oumer, A. N.; Hamidi, N. M.; Mat Sahat, I.

    2015-12-01

    Since the filling stage of injection molding process has important effect on the determination of the orientation state of the fibers, accurate analysis of the flow field for the mold filling stage becomes a necessity. The aim of the paper is to characterize the flow induced orientation state of short fibers in injection molding cavities. A dog-bone shaped model is considered for the simulation and experiment. The numerical model for determination of the fibers orientation during mold-filling stage of injection molding process was solved using Computational Fluid Dynamics (CFD) software called MoldFlow. Both the simulation and experimental results showed that two different regions (or three layers of orientation structures) across the thickness of the specimen could be found: a shell region which is near to the mold cavity wall, and a core region at the middle of the cross section. The simulation results support the experimental observations that for thin plates the probability of fiber alignment to the flow direction near the mold cavity walls is high but low at the core region. It is apparent that the results of this study could assist in decisions regarding short fiber reinforced polymer composites.

  18. Fuelling and plasma flow change by compact torus injection into the STOR-M Tokamak

    Science.gov (United States)

    Onchi, Takumi; Liu, Yelu; Dreval, Mykola; McColl, David; Xiao, Chijin; Hirose, Akira; Asai, Tomohiko; Wolfe, Sean

    2012-10-01

    The Saskatchewan TORus Modified (STOR-M) tokamak is equipped with a Compact Torus (CT) injector for tangential (toroidal) injection of a high density plasmoid at a velocity of 150 km/s. The objectives of CT injection (CTI) are to fuel the core region of tokamak and optimize the bootstrap current in future reactors by control of the plasma pressure gradient. After CTI, the line averaged density along central chord increases from ne˜x 10^12 to 1.5 x 10^13 [cm-3]. Measurement of soft X-ray bremsstrahlung emission profile indicates a steeper density gradient is generated after the asymmetric density profile is formed and the profile become symmetry again in STOR-M. Intrinsic impurity ion flows have been measured with ion Doppler spectroscopy. Significant radial velocity shear from center to edge region is observed even in Ohmic discharges. The toroidal flow direction is found to depend on the plasma current direction. CTI also modifies toroidal plasma flow. The edge plasma flow increases by 5 km/s 1millisecond after CTI. During these milliseconds of time, toroidal flow shear is also increased from 214.3 to 285.7 [10^3 x1/s]. A few milliseconds later than that time, plasma flow slows down, but plasma confinement is improved. Hα emission decreases by 50%.

  19. Three-dimensional numerical modeling of an induction heated injection molding tool with flow visualization

    DEFF Research Database (Denmark)

    Guerrier, Patrick; Tosello, Guido; Nielsen, Kaspar Kirstein

    2016-01-01

    Using elevated mold temperature is known to have a positive influence of final injection molded parts. Induction heating is a method that allow obtaining a rapid thermal cycle, so the overall molding cycle time is not increased. In the present research work, an integrated multi-turn induction...... heating coil has been developed and assembled into an injection molding tool provided with a glass window, so the effect of induction heating can directly be captured by a high speed camera. In addition, thermocouples and pressure sensors are also installed, and together with the high speed videos...... magnetic permeability. The three-dimensional transient thermal field of the mold cavity was then calculated and compared with the experiments. This thermal field was transferred to an injection molding flow solver to compare simulations and experimental results from the high speed video, both...

  20. Irreversibility analysis of magneto-hydrodynamic nanofluid flow injected through a rotary disk

    Directory of Open Access Journals (Sweden)

    Rashidi Mohammad Mehdi

    2015-01-01

    Full Text Available The non-linear Navier-Stokes equations governed on the nanofluid flow injected through a rotary porous disk in the presence of an external uniform vertical magnetic field can be changed to a system of non-linear partial differential equations by applying similar parameter. In this study, partial differential equations are analytically solved by the modified differential transform method, Pade differential transformation method to obtain self-similar functions of motion and temperature. A very good agreement is observed between the obtained results of Pade differential transformation method and those of previously published ones. Then it has become possible to do a comprehensive parametric analysis on the entropy generation in this case to demonstrate the effects of physical flow parameters such as magnetic interaction parameter, injection parameter, nanoparticle volume fraction, dimensionless temperature difference, rotational Brinkman number and the type of nanofluid on the problem.

  1. Recent Development in Optical Chemical Sensors Coupling with Flow Injection Analysis

    Directory of Open Access Journals (Sweden)

    Fuensanta Sánchez Rojas

    2006-10-01

    Full Text Available Optical techniques for chemical analysis are well established and sensors based on thesetechniques are now attracting considerable attention because of their importance in applications suchas environmental monitoring, biomedical sensing, and industrial process control. On the other hand,flow injection analysis (FIA is advisable for the rapid analysis of microliter volume samples and canbe interfaced directly to the chemical process. The FIA has become a widespread automatic analyticalmethod for more reasons; mainly due to the simplicity and low cost of the setups, their versatility, andease of assembling. In this paper, an overview of flow injection determinations by using opticalchemical sensors is provided, and instrumentation, sensor design, and applications are discussed. Thiswork summarizes the most relevant manuscripts from 1980 to date referred to analysis using opticalchemical sensors in FIA.

  2. Three-dimensional numerical modeling of an induction heated injection molding tool with flow visualization

    DEFF Research Database (Denmark)

    Guerrier, Patrick; Tosello, Guido; Nielsen, Kaspar Kirstein

    2016-01-01

    heating coil has been developed and assembled into an injection molding tool provided with a glass window, so the effect of induction heating can directly be captured by a high speed camera. In addition, thermocouples and pressure sensors are also installed, and together with the high speed videos...... magnetic permeability. The three-dimensional transient thermal field of the mold cavity was then calculated and compared with the experiments. This thermal field was transferred to an injection molding flow solver to compare simulations and experimental results from the high speed video, both...... with and without the effect of induction heating. A rapid thermal cycle was proved to be feasible in a mold with an integrated induction coil. Furthermore, it was shown that the process can be modeled with good accuracy, both in terms of the thermal field and of the flow pattern....

  3. Are Flow Injection-based Approaches Suitable for Automated Handling of Solid Samples?

    DEFF Research Database (Denmark)

    Miró, Manuel; Hansen, Elo Harald; Cerdà, Victor

    Flow-based approaches were originally conceived for liquid-phase analysis, implying that constituents in solid samples generally had to be transferred into the liquid state, via appropriate batch pretreatment procedures, prior to analysis. Yet, in recent years, much effort has been focused...... on the design and characterisation of sample processings units coupled with flowing systems aiming to enable the direct introduction and treatment of solid samples of environmental and agricultural origin in an automated fashion [1]. In this respect, various sample pre-treatment techniques including......, multisyringe flow injection, and micro-Lab-on-valve are presented as appealing approaches for on-line handling of solid samples. Special emphasis is given to the capability of flow systems to accommodate sequential extraction protocols for partitioning of trace elements and nutrients in environmental solids (e...

  4. Flow injection chemiluminescent determination of clenbuterol using GoldMag particles as carrier.

    Science.gov (United States)

    Li, Zhefei; Jian, Liru; Wang, Huirong; Cui, Yali

    2007-01-01

    A novel flow injection chemiluminescent (CL) enzyme immunoassay for clenbuterol analysis based on GoldMag particles is described. GoldMag is a new type of super-paramagnetic Fe3O4/Au composite particle used as a carrier in a flow injection CL system. Clenbuterol conjugated with ovalbumin (OVA) was immobilized onto GoldMag particles and the particles fixed in a micro-channel by an external electromagnetic field. The clenbuterol test sample and clenbuterol polyclonal antibody (Ab) were injected into the channel and incubated with GoldMag particles. Clenbuterol, immobilized on the magnetic particle surfaces, competes for polyclonal antibodies with clenbuterol in the test sample. The free Ab or Ab combined with the clenbuterol sample was washed away and the magnetic particles conjugated with Ag-Ab left in the micro-channel. Horseradish peroxidase (HRP)-labelled goat anti-rabbit immunoglobulin G (IgG) was added and reacted with clenbuterol polyclonal antibodies; excess goat anti-rabbit-HRP was then washed off. When chemiluminescent reagents were injected into the channel, emitted light from the magnetic particle surface was measured and recorded using a photomultiplier-based apparatus. The linear range of this novel method was 0.01-0.1 ng g(-1) and recovery of clenbuterol was 85-105% with a RSD of 3.2% (n = 11).

  5. Modelling and Simulation of Structural Deformation of Isothermal Subsurface Flow and Carbon Dioxide Injection

    KAUST Repository

    El-Amin, Mohamed

    2011-05-15

    Injection of CO2 in hydrocarbon reservoir has double benefit. On the one hand, it is a profitable method due to issues related to global warming, and on the other hand it is an effective mechanism to enhance hydrocarbon recovery. Such injection associates complex processes involving, e.g., solute transport of dissolved materials, in addition to local changes in density of the phases. Also, increasing carbon dioxide injection may cause a structural deformation of the medium, so it is important to include such effect into the model. The structural deformation modelling in carbon sequestration is important to evaluate the medium stability to avoid CO2 leakage to the atmosphere. On the other hand, geologic formation of the medium is usually heterogeneous and consists of several layers of different permeability. In this work we conduct numerical simulation of two-phase flow in a heterogeneous porous medium domain with dissolved solute transport as well as structural deformation effects. The solute transport of the dissolved component is described by concentration equation. The structural deformation for geomechanics is derived from a general local differential balance equation with neglecting the local mass balance of solid phase and the inertial force term. The flux continuity condition is used at interfaces between different permeability layers of the heterogeneous medium. We analyze the vertical migration of a CO2 plume injected into a 2D layered reservoir. Analysis of distribution of flow field components such as saturation, pressures, velocities, and CO2 concentration are presented.

  6. Numerical Simulation of Magnetic Nanoparticles Injection into Two–phase Flow in a Porous Medium

    KAUST Repository

    El-Amin, Mohamed

    2017-06-09

    In this paper, the problem of magnetic nanoparticles injection into a water–oil two–phase flow under an external permanent magnetic field is investigated. The mathematical model of the problem under consideration has been developed. We treat the water-nanoparticles suspension as a miscible mixture while it is immiscible with the oil phase. The magnetized phase pressure includes an additional pressure term with the conventional thermodynamic pressure. The countercurrent imbibition flow problem is taken as an example. Physical variables including water–nanoparticles suspension saturation, nanoparticles concentration, and pore wall/throat deposited nanoparticles are investigated under the influence of the magnetic field.

  7. Micelle-mediated methodology for the preconcentration of uranium prior to its determination by flow injection

    Energy Technology Data Exchange (ETDEWEB)

    Fernandez Laespada, M.E.; Perez Pavon, J.L.; Moreno Cordero, B. (Univ. de Salamanca (Spain). Dept. de Quimica Analitica, Nutricion y Bromatologia)

    1993-02-01

    Cloud point extraction has been used for the preconcentration of uranium, prior to its determination by flow injection. The non-ionic surfactant employed was Triton X-114 and the reagent chosen to form a hydrophobic chelate of uranium was 1-(2-pyridylazo)-2-naphthol. The optimum conditions for the preconcentration and determination of uranium have been studied. This methodology has been applied to the determination of trace amounts of uranium in tap and river waters from Salamanca. (Author).

  8. Flow-fiber coupled viscosity in injection molding simulations of short fiber reinforced thermoplastics

    OpenAIRE

    LI, Tianyi; Luyé, Jean-François

    2018-01-01

    The main objective of this communication is to numerically investigate the use of fiber-dependent viscosity models in injection molding simulations of short fiber reinforced thermoplastics with a latest commercial software (Moldflow Insight 2018). We propose to use the homogenization-based Lipscomb's model to take into account possible flow-fiber coupling effects. The original model is adapted and then implemented in the Moldflow Insight API framework. Numerical simulations are performed in a...

  9. Differentiating Organic from Conventional Peppermints Using Chromatographic and Flow-Injection Mass Spectrometric (FIMS) Fingerprints

    OpenAIRE

    Gao, Boyan; Lu, Yingjian; Qin, Fang; Chen, Pei; Shi, Haiming; Charles, Denys; Yu, Liangli (Lucy)

    2012-01-01

    High performance liquid chromatography (HPLC) and flow-injection mass spectrometric (FIMS) fingerprinting techniques were tested for their potential in differentiating organic and conventional peppermint samples. Ten organic and ten conventional peppermint samples were examined using HPLC-UV and FIMS methods. The principal component analysis (PCA) showed that both HPLC and FIMS fingerprints could determine the difference in the commercial organic and conventional peppermints. FIMS fingerprint...

  10. Determination of mercury by multisyringe flow injection system with cold-vapor atomic absorption spectrometry

    Energy Technology Data Exchange (ETDEWEB)

    Leal, L.O. [Department of Chemistry, University of the Balearic Islands, Carretera de Valldemossa km.7.5, E-07122 Palma de Mallorca (Spain); Elsholz, O. [Hamburg University of Applied Sciences, Lohbruegger Kirchstrasse 65, 21033 Hamburg (Germany); Forteza, R. [Department of Chemistry, University of the Balearic Islands, Carretera de Valldemossa km.7.5, E-07122 Palma de Mallorca (Spain); Cerda, V. [Department of Chemistry, University of the Balearic Islands, Carretera de Valldemossa km.7.5, E-07122 Palma de Mallorca (Spain)]. E-mail: victor.cerda@uib.es

    2006-07-28

    A new software-controlled time-based multisyringe flow injection system for mercury determination by cold-vapor atomic absorption spectrometry is proposed. Precise known volumes of sample, reducing agent (1.1% SnCl{sub 2} in 3% HCl) and carrier (3% HCl) are dispensed into a gas-liquid separation cell with a multisyringe burette coupled with one three-way solenoid valve. An argon flow delivers the reduced mercury to the spectrometer. The optimization of the system was carried out testing reaction coils and gas-liquid separators of different design as well as changing parameters, such as sample and reagents volumes, reagent concentrations and carrier gas flow rate, among others. The analytical curves were obtained within the range 50-5000 ng L{sup -1}. The detection limit (3{sigma} {sub b}/S) achieved is 5 ng L{sup -1}. The relative standard deviation (R.S.D.) was 1.4%, evaluated from 16 successive injections of 250 ng L{sup -1} Hg standard solution. The injection and sample throughput per hour were 44 and 11, respectively. This technique was validated by means of solid and water reference materials with good agreement with the certified values and was successfully applied to fish samples.

  11. Fluid flow separation in a reactor pressure vessel during an ECC injection. Single phase flow and two phase flow (air-water) experimental results

    Energy Technology Data Exchange (ETDEWEB)

    Thierry Bichet; Alain Martin [EDF - Research and Development Division - Fluid Mechanics and Heat Transfert 6, quai Watier - B.P. 49 - 78401 Chatou CEDEX 01 (France); Frederic Beaud [EDF/ Industry - Basic Design Department., 12-14, Avenue Dutrievoz 69628 Villeurbanne CEDEX (France)

    2005-07-01

    Full text of publication follows: Within the framework of the nuclear power plant lifetime issue, the assessment of the French 900 MWe (3-loops) series reactor pressure vessel (RPV) integrity has been performed. A simplified analysis has shown that the most severe loading conditions are given by the small break loss of coolant accidents due to the pressurized injection of cold water (9 deg. C) into the cold leg and down comer of the RPV. During these transient scenarios, single or two-phase (uncovered cold leg) flows have been shown in the cold leg, depending on the crack size and RPV model (900 MWe or 1300 MWe). An experimental study has been carried out, on the one hand, to consolidate the numerical results obtained with CFD home code (Code-Saturne) which mainly showed the stratified flow in the cold leg and the fluid flow separation and its oscillations in the down comer during a single phase scenario. These physical phenomena are important for the thermal RPV loading assessment. On the other hand, the absence of experimental two-phase data necessitated to carry out an experimental study around the mixing area behavior (free surface, stratified flow) during an ECC injection with an uncovered cold leg. The new EDF R and D mock up, called HYBISCUS, is a facility which is made out of Plexiglas (atmosphere pressure) and represents a half scale CP0 geometry with one cold leg and part of the down comer. The mock up modularity allows us to insert representative ECC nozzles and a thermal shield. In reference to the reactor scenarios, the experimental operating conditions are derived from the conservation of the density effects (Froude number). For that, a heated salted water flow is used to represent the ECC injection whereas water represents the cold leg fluid. This mock up has been defined in order to represent single phase flow (cold leg and down comer full of water) or two-phase flow (uncovered cold leg) ECC scenarios. This paper reports experimental results

  12. Indications of Segmental Flow in Straight Pipes by Flow Injection with Spectrophotometric Detection

    DEFF Research Database (Denmark)

    Andersen, Jens Enevold Thaulov

    2000-01-01

    A procedure of spectrophotometric analysis of fluid flow in pipes is described and its performance is tested on three different dye compounds. The procedure follows measurement and mathematical de-convolution of the signal with an exponential function that is associated with molecular diffusion. ...

  13. Exploitation of pulsed flows for on-line dispersive liquid-liquid microextraction: Spectrophotometric determination of formaldehyde in milk.

    Science.gov (United States)

    Nascimento, Carina F; Brasil, Marcos A S; Costa, Susana P F; Pinto, Paula C A G; Saraiva, Maria Lúcia M F S; Rocha, Fábio R P

    2015-11-01

    Formaldehyde is often added to foods as a preservative, but it is highly toxic to humans, having been identified as a carcinogenic substance. It has also been used for the adulteration of milk in order to diminish the bacteria count and increase the shelf life of the product. Herein, we present a green dispersive liquid-liquid microextraction procedure in a flow-batch system for the determination of formaldehyde in milk. Pulsed flows were exploited for the first time to improve the dispersion of the extractant in the aqueous phase. The Hantzsch reaction was used for the derivatization of formaldehyde and the product was extracted with the ionic liquid (IL) trihexyltetradecylphosphonium chloride with methanol as the disperser. The flow-batch chamber was made of stainless steel with the facility for resistive heating to speed up the derivatization reaction. Spectrophotometric measurements were directly carried out in the organic phase using an optical fiber spectrophotometer. The limit of detection and coefficient of variation were 100 μg L(-1) and 3.1% (n=10), respectively, with a linear response from 0.5 to 5.0 mg L(-1), described by the equation A=0.088+0.116CF (mg L(-1)) in which A is absorbance and CF is formaldehyde concentration in mg L(-1). The estimated recoveries of formaldehyde from spiked milk samples ranged from 91% to 106% and the slopes of the analytical curves obtained with reference solutions in water or milk were in agreement, thus indicating the absence of matrix effects. Accuracy was demonstrated by the agreement of the results with those achieved by the reference fluorimetric procedure at the 95% confidence level. The proposed procedure allows for 10 extractions per hour, with minimized reagent consumption (120 μL of IL and 3.5 μL acetylacetone) and generation of only 6.7 mL waste per determination, which contribute to the eco-friendliness of the procedure. Copyright © 2015 Elsevier B.V. All rights reserved.

  14. Stopped-flow injection spectrophotometric method for determination of chlorate in soil

    Directory of Open Access Journals (Sweden)

    Jaroon Jakmunee

    2008-06-01

    Full Text Available A stopped-flow injection (FI spectrophotometric procedure based on iodometric reaction for the determination of chlorate has been developed. Standard/sample was injected into a stream of potassium iodide solution and then merged with a stream of hydrochloric acid solution to produce triiodide. By stopping the flow while the sample zone is being in a mixing coil, a slow reaction of chlorate with iodide in acidic medium was promoted to proceed with minimal dispersion of the triiodide product zone. When the flow started again, a concentrated product zone was pushed into a flow cell and a signal profile due to light absorption of the product was recorded. Employing a lab-built semi-automatic stopped-FI analyser, the analysis can be performed with higher degree of automation and low chemical consumption. Linear calibration graph in the range of 5-50 mg ClO3- L-1 was obtained, with detection limit of 1.4 mg ClO3- L-1. Relative standard deviation of 2.2% (30 mg ClO3- L-1, n=10 and sample throughput of about 20 h-1 were achieved. The system was applied to soil samples and validated by batch spectrophotometric and standard titrimetric methods.

  15. An automatic flow injection analysis procedure for photometric determination of ethanol in red wine without using a chromogenic reagent.

    Science.gov (United States)

    Borges, Sivanildo S; Frizzarin, Rejane M; Reis, Boaventura F

    2006-05-01

    An automatic reagentless photometric procedure for the determination of ethanol in red wine is described. The procedure was based on a falling drop system that was implemented by employing a flow injection analysis manifold. The detection system comprised an infrared LED and a phototransistor. The experimental arrangement was designed to ensure that the wine drop grew between these devices, thus causing a decrease in the intensity of the radiation beam coming from the LED. Since ethanol content affected the size of the wine drop this feature was exploited to develop an analytical procedure for the photometric determination of ethanol in red wine without using a chromogenic reagent. In an attempt to prove the usefulness of the proposed procedure, a set of red wines were analysed. No significant difference between our results and those obtained with a reference method was observed at the 95% confidence level. Other advantages of our method were a linear response ranging from 0.17 up to 5.14 mol L(-1) (1.0 up to 30.0%) ethanol (R = 0.999); a limit of detection of 0.05 mol L(-1) (0.3%) ethanol; a relative standard deviation of 2.5% (n = 10) using typical wine sample containing 2.14 mol L(-1) (12.5%) ethanol; and a sampling rate of 50 determinations per hour.

  16. Detecting total toxicity in water using a mediated biosensor system with flow injection.

    Science.gov (United States)

    Yong, Daming; Liu, Changyu; Zhu, Chengzhou; Yu, Dengbin; Liu, Ling; Zhai, Junfeng; Dong, Shaojun

    2015-11-01

    A novel total toxicity detection method based on a mediated biosensor system with flow injection (MB-FI) was developed to rapidly and reliably detect respiration inhibitors (i.e., As2O3, KCN, salicylic acid (SA), 2,4-dintirophenol (DNP)) in water. The mediated biosensor toxicity assessment using microorganisms immobilized in calcium alginate filaments can greatly simplify the testing process and save time. In the MB-FI system, ferricyanide together with a respiration inhibitor was injected into the bioreactor, inhibiting the respiration of the immobilized microorganisms. The degree of inhibition was measured by determining the ferrocyanide generated in the effluent, expressed as the 50% inhibition concentration (IC50). The IC50 values for the four respiration inhibitors obtained using this method were comparable to those obtained using the classic method, confirming that this approach is an alternative alert method. More importantly, this constructed biosensor system with flow injection will facilitate the application and commercialization of this toxicity monitoring technology. Copyright © 2015 Elsevier Ltd. All rights reserved.

  17. MHD flow over a permeable stretching/shrinking sheet of a nanofluid with suction/injection

    Directory of Open Access Journals (Sweden)

    Sandeep Naramgari

    2016-06-01

    Full Text Available In this study we analyzed the influence of thermal radiation and chemical reaction on two dimensional steady magnetohydrodynamic flow of a nanofluid past a permeable stretching/shrinking sheet in the presence of suction/injection. We considered nanofluid volume fraction on the boundary is submissive controlled, which makes the present study entirely different from earlier studies and physically more realistic. The equations governing the flow are solved numerically. Effects of non-dimensional governing parameters on velocity, temperature and concentration profiles are discussed and presented through graphs. Also, coefficient of skin friction and local Nusselt number is investigated for stretching/shrinking and suction/injection cases separately and presented through tables. Comparisons with existed results are presented. Present results have an excellent agreement with the existed studies under some special assumptions. Results indicate that the enhancement in Brownian motion and thermophoresis parameters depreciates the nanoparticle concentration and increases the mass transfer rate. Dual solutions exist only for certain range of stretching/shrinking and suction/injection parameters.

  18. Visualization analysis of tiger-striped flow mark generation phenomena in injection molding

    Science.gov (United States)

    Owada, Shigeru; Yokoi, Hidetoshi

    2016-03-01

    The generation mechanism of tiger-striped flow marks of polypropylene (PP)/rubber/talc blends in injection molding was investigated by dynamic visualization analysis in a glass-inserted mold. The analysis revealed that the behavior of the melt flow front correlates with the flow mark generation. The cloudy part in the tiger-striped flow marks corresponded to the low transcription rate area of the melt diverging near the cavity wall, while the glossy part corresponded to the high transcription rate area of the melt converging toward the cavity wall side. The melt temperature at the high transcription rate area was slightly lower than that at the low transcription rate area. These phenomena resulted due to the difference in the temperature of the melt front that was caused by the asymmetric fountain flow. These results suggest the followings; At the moment when the melt is broken near the one side of cavity wall due to piling the extensional strains up to a certain level, the melt spurts out near the broken side. It results in generating asymmetric fountain flow temporarily to relax the extensional front surface, which moves toward the opposite side to form the high transcription area.

  19. Exploiting gas diffusion for non-invasive sampling in flow analysis: determination of ethanol in alcoholic beverages

    Directory of Open Access Journals (Sweden)

    Simone Vicente

    2006-03-01

    Full Text Available A tubular gas diffusion PTFE membrane is exploited for non-invasive sampling in flow analysis, aiming to develop an improved spectrophotometric determination of ethanol in alcoholic beverages. The probe is immersed into the sample, allowing ethanol to diffuse through the membrane. It is collected into the acceptor stream (acidic dichromate solution, leading to formation of Cr(III, monitored at 600 nm. The analytical curve is linear up to 50% (v/v ethanol, baseline drift is Uma membrana tubular de PTFE permeável a espécies gasosas foi empregada como sonda em sistemas de análises em fluxo visando a proposta de uma estratégia de amostragem não invasiva. Como aplicação, foi selecionada a determinação espectrofotométrica de etanol em bebidas alcoólicas. A sonda é imersa na amostra, permitindo que o analito se difunda através desta e seja coletado pelo fluxo aceptor (solução ácida de dicromato, levando à formação de Cr(III, o qual é monitorado a 600 nm. Linearidade da curva analítica é verificada até 50,0% (v/v de etanol (r > 0,998; n = 8, derivas de linha base são menores do que 0,005 absorbância durante períodos de 4 horas de operação e a velocidade analítica é de 30 h-1 o que corresponde a 0.6 mmol K2Cr2O7 por determinação. Os resultados são precisos (d.p.r. < 2% e concordantes com aqueles obtidos por um método oficial.

  20. The effect of saturation on resin flow in injection pultrusion: a preliminary numerical study

    DEFF Research Database (Denmark)

    Spangenberg, Jon; Larsen, Martin; R. Rodríguez, Rosa

    In this study, a 2-D Darcy’s law based numerical model is developed in order to investigate the effect of saturation on the propagation of the resin in the die chamber of a pultrusion line. The numerical model is established using the finite volume method and alternating direction implicit scheme....... The implemented saturation and relative permeability curves are adopted from relationships presented in the literature. The results of the numerical model highlights the importance of accurately determining thesaturation curve when included in a numerical solver that is used to predict the resin flow in injection...... pultrusion. Further research is planned within this field in order to identify realistic saturation curves for fiber reinforcements used in resin injection pultrusion....

  1. O-(β-hydroxyethylrutosides determination by micellar flow injection (FI-spectrofluorimetry

    Directory of Open Access Journals (Sweden)

    Cecilia Mariana Peralta

    2014-12-01

    Full Text Available A simple, eco-friendly, sensitive and economic flow injection spectrofluorimetric method was developed for the determination of O-(β-hydroxyethylrutosides. The procedure was based on the use of an anionic surfactant such as sodium dodecyl sulfate to provide an appreciable O-(β-hydroxyethylrutosides fluorescence enhancement, increasing considerably the sensitivity of detection. All the variables affecting the fluorescence intensity were studied and optimized. The flow rate was 5 mL/min with detection at 450 nm (after excitation at 346 nm. A linear correlation between drug amount and peak area was established for O-(β-hydroxyethylrutosides in the range of 0.01–200 µg/mL with a detection limit of 0.001 µg/mL (s/n=3. Validation processes were performed by recovering studies with satisfactory results. The new methodology can be employed for the routine analysis of O-(β-hydroxyethylrutosides in bulks as well as in commercial formulations. Keywords: O-(β-hydroxyethylrutosides, Micellar enhancement, Flow injection, Spectrofluorimetry, Pharmaceuticals

  2. Antimony determination and speciation by multisyringe flow injection analysis with hydride generation-atomic fluorescence detection

    Energy Technology Data Exchange (ETDEWEB)

    Semenova, N.V. [Department of Geography, Lomonosov State University, Moscow 119899 (Russian Federation); Leal, L.O. [Department of Chemistry, University of the Balearic Islands, Carretera de Valldemossa, km.7.5, E-07122 Palma de Mallorca (Spain); Forteza, R. [Department of Chemistry, University of the Balearic Islands, Carretera de Valldemossa, km.7.5, E-07122 Palma de Mallorca (Spain); Cerda, V. [Department of Chemistry, University of the Balearic Islands, Carretera de Valldemossa, km.7.5, E-07122 Palma de Mallorca (Spain)]. E-mail: vcerda@p01.uib.es

    2005-02-07

    A new analytical procedure for determination of inorganic antimony and speciation of antimony(III) and antimony(V) is presented. For this purpose, a software-controlled time-based multisyringe flow injection system, which contains a multisyringe burette provided with a multi-port selection valve, was developed. Hydride generation-atomic fluorescence spectrometry was used as a detection technique. A 0.3% (w/v) reducing sodium tetrahydroborate solution, hydrochloric acid (2 M), an antimony solution and a pre-reducing solution of 10% (w/v) KI and 0.3% (w/v) ascorbic acid are dispensed simultaneously into a gas-liquid separation cell with further propulsion of the reaction product into the flame of an atomic fluorescence spectrometer using argon flow. A hydrogen flow was employed to support the flame. The linear range and the detection limit (3s{sub b}/S) of the proposed technique were 0.2-5.6 {mu}g l{sup -1} and 0.08 {mu}g l{sup -1}, respectively. A sample throughput of 18 samples per hour (corresponding to 80 injections per hour) was achieved. The relative standard deviation for 18 independent measurements was 4.6%. This technique was validated by means of reference solid and water materials with good agreement with the certified values. Satisfactory results for speciation of Sb(III) and Sb(V) by means of the developed technique were obtained.

  3. Flow injection determination of anisidine value in palm oil samples using a triiodide potentiometric detector.

    Science.gov (United States)

    Saad, Bahruddin; Wai, Wan Tatt; Lim, Boey Peng; Saleh, Muhammad Idiris

    2007-05-22

    A flow injection analysis (FIA) procedure for the determination of anisidine value (AV) in palm olein using a triiodide detector is described. Undiluted oil sample and chloramine-T reagent were added to a reaction chamber, and reaction was accelerated by applying a short vortex action (typically for 30 s). After allowing the emulsified oil phase to be separated from the aqueous phase (bottom layer), an aliquot of the aqueous phase (containing unreacted chloramine-T) was aspirated into a carrier stream that contained I(-) where the chloramine-T oxidized the I- to form I3(-) which was finally detected by a flow-through triiodide potentiometric detector. Variables that affect the FIA signals such as size of the reaction chamber, oil and reagent flow rates, chloramine-T concentration, vortex time, time for phase separation, carrier stream pH and injected volume were studied. The optimized FIA procedure is linear over 1.0-23.0 AV. The method exhibits good repeatabililty (R.S.D. of +/-3.16% (n = 4) for the determination of 5.0 AV) and a sampling rate of 40 samples per hour was achieved. Good correlation (r2 = 0.996 (n = 4)) between the proposed method and the manual American Oil Chemists' Society procedure was found when applied to the determination of twenty different types of palm olein samples.

  4. Flow and injection characteristics of pharmaceutical parenteral formulations using a micro-capillary rheometer.

    Science.gov (United States)

    Allahham, Ayman; Stewart, Peter; Marriott, Jennifer; Mainwaring, David E

    2004-02-11

    A micro-capillary rheometer consisted of a fine needle with an internal diameter of 347 microm attached to a 1 ml removable-needle syringe within an Instron device that operated in compression mode to provide various crosshead speeds ranging from 150 to 950 mm min(-1) covering typical clinical injection rates, and that determined the resulting force on the plunger. The crosshead speed and the resulting force were used to calculate the shear rate and the shear stress respectively. These were used in standard capillary flow expressions together with an independent measurement of the wall frictional force and allowed the viscosity of parenteral Newtonian solutions and non-Newtonian suspensions to be measured quantitatively and their rheological behaviour in needles of clinical dimensions to be established. Commercial pharmaceutical parenteral formulations consisting of three oil-based solutions and three aqueous suspensions were chosen for this study. The net injection forces were also obtained and it was shown that both the oil-based solutions and the aqueous suspensions covered similar ranges. The viscosities for the parenteral solutions were determined from the slope of the linear regression (R(2)>0.97) between shear stress and shear rate and ranged between 0.029 and 0.060 Pas. For the aqueous suspensions examined, viscosities decreased from low shear rate to high shear rate, following a power-law model and indicating a pseudo plastic behaviour. Standardisation of the micro-capillary rheometer with Newtonian silicone oils calibrated with a Rheometrics Fluids Spectrometer showed viscosity values consistent between the rotational flow measurements and capillary flow measurements which were within 5% and showed very high degrees of reproducibility between replicate samples. This degree of reproducibility allowed differences in the contribution of the wall frictional force to the required plunger force for both the oil-based and aqueous parenteral formulations to be

  5. Flow-injection chemiluminescence determination of chloroquine using peroxynitrous acid as oxidant.

    Science.gov (United States)

    Liang, Yao-Dong; Song, Jun-Feng; Yang, Xiao-Feng; Guo, Wei

    2004-03-10

    A new flow-injection chemiluminescence (CL) method for determination of chloroquine is proposed based on a stronger chemiluminescence of chloroquine in hydrogen peroxide-nitrite-sulfuric acid medium. The proposed method allows the measurement of chloroquine over the range of 3.0x10(-7) to 1.0x10(-5)moll(-1). The detection limit is 8.6x10(-8)moll(-1), and the relative standard deviation for 1.0x10(-6)moll(-1) chloroquine (n=11) is 1.6%. The CL mechanism is also discussed.

  6. Flow Injection and Atomic Absorption Spectrometry - An Effective and Attractive Analytical Chemical Combination

    DEFF Research Database (Denmark)

    Hansen, Elo Harald; Nielsen, Steffen

    1998-01-01

    One of the advantages of the flow injection (FI) concept is that it is compatible with virtually all detection techniques. Being a versatile vehicle for enhancing the performance of the individual detection devices, the most spectacular results have possibly been obtained in conjunction with atomic...... absorption spectrometry (AAS). Initially with flame-AAS (FAAS) procedures, later for hydride generation (HG) techniques, and most recently in combination with electrothermal AAS (ETAAS). The common denominator for all these procedures is the inherently precise and strictly reproducible timing that the sample...

  7. The Application of Flow Injection Technology to Automating Cold Vapor Mercury Analyses in Aquatic Ecosystems

    Directory of Open Access Journals (Sweden)

    TEODOROF, L.

    2009-02-01

    Full Text Available Based on flow injection techniques, FIMS is fully automated, fast, and cost-effective. The FIMS uses a high-performance single-beam optical system with a low pressure mercury lamp and solar-blind detector for maximum performance. The FIMS-400 has two stepper motor-driven peristaltic pumps for greater flexibility when used with optional accessories. FIMS is fully controlled from a personal computer using WinLab32 for AA software, a true Microsoft Windows-based program with an unparalleled offering of standard features, including a full range of analytical checks and quality control functions.

  8. Rapid detection of milk adulteration using intact protein flow injection mass spectrometric fingerprints combined with chemometrics.

    Science.gov (United States)

    Du, Lijuan; Lu, Weiying; Cai, Zhenzhen Julia; Bao, Lei; Hartmann, Christoph; Gao, Boyan; Yu, Liangli Lucy

    2018-02-01

    Flow injection mass spectrometry (FIMS) combined with chemometrics was evaluated for rapidly detecting economically motivated adulteration (EMA) of milk. Twenty-two pure milk and thirty-five counterparts adulterated with soybean, pea, and whey protein isolates at 0.5, 1, 3, 5, and 10% (w/w) levels were analyzed. The principal component analysis (PCA), partial least-squares-discriminant analysis (PLS-DA), and support vector machine (SVM) classification models indicated that the adulterated milks could successfully be classified from the pure milks. FIMS combined with chemometrics might be an effective method to detect possible EMA in milk. Copyright © 2017 Elsevier Ltd. All rights reserved.

  9. Automatic On-line Solid-phase Extraction-Electrothermal Atomic Absorption Spectrometry Exploiting Sequential Injection Analysis for Trace Vanadium, Cadmium and Lead Determination in Human Urine Samples.

    Science.gov (United States)

    Giakisikli, Georgia; Ayala Quezada, Alejandro; Tanaka, Junpei; Anthemidis, Aristidis N; Murakami, Hiroya; Teshima, Norio; Sakai, Tadao

    2015-01-01

    A fully automated sequential injection column preconcentration method for the on-line determination of trace vanadium, cadmium and lead in urine samples was successfully developed, utilizing electrothermal atomic absorption spectrometry (ETAAS). Polyamino-polycarboxylic acid chelating resin (Nobias chelate PA-1) packed into a handmade minicolumn was used as a sorbent material. Effective on-line retention of chelate complexes of analytes was achieved at pH 6.0, while the highest elution effectiveness was observed with 1.0 mol L(-1) HNO3 in the reverse phase. Several analytical parameters, like the sample acidity, concentration and volume of the eluent as well as the loading/elution flow rates, have been studied, regarding the efficiency of the method, providing appropriate conditions for the analysis of real samples. For a 4.5 mL sample volume, the sampling frequency was 27 h(-1). The detection limits were found to be 3.0, 0.06 and 2.0 ng L(-1) for V(V), Cd(II) and Pb(II), respectively, with the relative standard deviations ranging between 1.9 - 3.7%. The accuracy of the proposed method was evaluated by analyzing a certified reference material (Seronorm(TM) trace elements urine) and spiked urine samples.

  10. Flow Control in a Transonic Diffuser through Mass and Vorticity Injection to Mitigate Massive Separation

    Science.gov (United States)

    Gartner, Jeremy

    generators, sweeping jets array, pulsed jets array, segmented jet, and 2-D steady and unsteady jets, which were placed at different streamwise locations relative to the separation point, and different throat widths in order to compare the effect of the momentum coefficient over the effect of the mass flow ratio. Note that the segmented jet and the 2-D jets were investigated under steady and unsteady injection with two different RMS values (low and high RMS). The highest pressure recovery achieved by the presence of the vortex generators was when they were erected into the flow at the height corresponding to the local boundary layer thickness (h/delta=1). The sweeping jets array achieved similar performance as the pulsed jets arrays. Moreover, they outperformed the 2-D jets, located at the same streamwise location, both in pressure recovery and in symmetry of the flow. The 2-D jet and the segmented jet located closer to the separation point (at x/L=0.25) resulted in a more efficient flow reattachment, resulting in a higher pressure recovery than for the 2-D jets located at the beginning of the ramp. Also, the effect of mass flow ratio and momentum coefficient was investigated, leading to the conclusion that both parameters are necessary to compare the effectiveness of flow control actuators. Furthermore, the 2-D jets and the segmented jet were investigated under two unsteady conditions--with a low RMS unsteady injection and a high RMS unsteady injection. Independently to the actuator, the steady jet consistently resulted in a slightly asymmetric flow field. Also, the low RMS unsteady jet performed slightly better than the steady jet, whereas the high RMS outperformed significantly the steady jet and the low RMS unsteady jet, independently to its actuation frequency. Moreover, the performances of the high RMS unsteady jet were consistently higher at an actuation frequency of 200 Hz, which corresponds to the shedding frequency of the separated flow. In addition, it was found

  11. Flow Rates Measurement and Uncertainty Analysis in Multiple-Zone Water-Injection Wells from Fluid Temperature Profiles.

    Science.gov (United States)

    Reges, José E O; Salazar, A O; Maitelli, Carla W S P; Carvalho, Lucas G; Britto, Ursula J B

    2016-07-13

    This work is a contribution to the development of flow sensors in the oil and gas industry. It presents a methodology to measure the flow rates into multiple-zone water-injection wells from fluid temperature profiles and estimate the measurement uncertainty. First, a method to iteratively calculate the zonal flow rates using the Ramey (exponential) model was described. Next, this model was linearized to perform an uncertainty analysis. Then, a computer program to calculate the injected flow rates from experimental temperature profiles was developed. In the experimental part, a fluid temperature profile from a dual-zone water-injection well located in the Northeast Brazilian region was collected. Thus, calculated and measured flow rates were compared. The results proved that linearization error is negligible for practical purposes and the relative uncertainty increases as the flow rate decreases. The calculated values from both the Ramey and linear models were very close to the measured flow rates, presenting a difference of only 4.58 m³/d and 2.38 m³/d, respectively. Finally, the measurement uncertainties from the Ramey and linear models were equal to 1.22% and 1.40% (for injection zone 1); 10.47% and 9.88% (for injection zone 2). Therefore, the methodology was successfully validated and all objectives of this work were achieved.

  12. Flow Rates Measurement and Uncertainty Analysis in Multiple-Zone Water-Injection Wells from Fluid Temperature Profiles

    Directory of Open Access Journals (Sweden)

    José E. O. Reges

    2016-07-01

    Full Text Available This work is a contribution to the development of flow sensors in the oil and gas industry. It presents a methodology to measure the flow rates into multiple-zone water-injection wells from fluid temperature profiles and estimate the measurement uncertainty. First, a method to iteratively calculate the zonal flow rates using the Ramey (exponential model was described. Next, this model was linearized to perform an uncertainty analysis. Then, a computer program to calculate the injected flow rates from experimental temperature profiles was developed. In the experimental part, a fluid temperature profile from a dual-zone water-injection well located in the Northeast Brazilian region was collected. Thus, calculated and measured flow rates were compared. The results proved that linearization error is negligible for practical purposes and the relative uncertainty increases as the flow rate decreases. The calculated values from both the Ramey and linear models were very close to the measured flow rates, presenting a difference of only 4.58 m³/d and 2.38 m³/d, respectively. Finally, the measurement uncertainties from the Ramey and linear models were equal to 1.22% and 1.40% (for injection zone 1; 10.47% and 9.88% (for injection zone 2. Therefore, the methodology was successfully validated and all objectives of this work were achieved.

  13. Plasma heating, electric fields and plasma flow by electron beam ionospheric injection

    Science.gov (United States)

    Winckler, J. R.; Erickson, K. N.

    1990-01-01

    The electric fields and the floating potentials of a Plasma Diagnostics Payload (PDP) located near a powerful electron beam injected from a large sounding rocket into the auroral zone ionosphere have been studied. As the PDP drifted away from the beam laterally, it surveyed a region of hot plasma extending nearly to 60 m radius. Large polarization electric fields transverse to B were imbedded in this hot plasma, which displayed large ELF wave variations and also an average pattern which has led to a model of the plasma flow about the negative line potential of the beam resembling a hydrodynamic vortex in a uniform flow field. Most of the present results are derived from the ECHO 6 sounding rocket mission.

  14. Spectrophotometric bioanalytical flow-injection system for control of hemodialysis treatment.

    Science.gov (United States)

    Radomska, A; Glab, S; Koncki, R

    2001-09-01

    A spectrophotometric flow-injection analysis (FIA) system for monitoring clinical hemodialysis is demonstrated. The role of a dialysate urea detector incorporated in this bioanalytical system is played by an optical flow-through biosensor based on Prussian Blue film with chemically linked urease forming a monomolecular layer of the enzyme. This pH-enzyme optode-FIA system is useful for the selective determination of post-dialysate urea in the range of concentration corresponding to its level in real clinical samples (2-16 mmol l(-1)). This bioanalytical system allows the analysis of about 15 samples of spent dialysate per hour. The operational and storage stabilities of the applied biosensor are longer than 2 weeks and 2 months, respectively. Clinical evaluation of the bioanalytical system was performed.

  15. Effect of Trailing Edge Flow Injection on Fan Noise and Aerodynamic Performance

    Science.gov (United States)

    Fite, E. Brian; Woodward, Richard P.; Podboy, Gary G.

    2006-01-01

    An experimental investigation using trailing edge blowing for reducing fan rotor/guide vane wake interaction noise was completed in the NASA Glenn 9- by 15-foot Low Speed Wind Tunnel. Data were acquired to measure noise, aerodynamic performance, and flow features for a 22" tip diameter fan representative of modern turbofan technology. The fan was designed to use trailing edge blowing to reduce the fan blade wake momentum deficit. The test objective was to quantify noise reductions, measure impacts on fan aerodynamic performance, and document the flow field using hot-film anemometry. Measurements concentrated on approach, cutback, and takeoff rotational speeds as those are the primary conditions of acoustic interest. Data are presented for a 2% (relative to overall fan flow) trailing edge injection rate and show a 2 dB reduction in Overall Sound Power Level (OAPWL) at all fan test speeds. The reduction in broadband noise is nearly constant and is approximately 1.5 dB up to 20 kHz at all fan speeds. Measurements of tone noise show significant variation, as evidenced by reductions of up to 6 dB in the 2 BPF tone at 6700 rpm.: and increases of nearly 2 dB for the 4 BPF tone at approach speed. Aerodynamic performance measurements show the fan with 2 % injection has an overall efficiency that is comparable to the baseline fan and operates, as intended, with nearly the same pressure ratio and mass flow parameters. Hot-film measurements obtained at the approach operating condition indicate that mean blade wake filling in the tip region was not as significant as expected. This suggests that additional acoustic benefits could be realized if the trailing edge blowing could be modified to provide better filling of the wake momentum deficit. Nevertheless, the hot-film measurements indicate that the trailing edge blowing provided significant reductions in blade wake turbulence. Overall, these results indicate that further work may be required to fully understand the proper

  16. Development of a Fully Automated Flow Injection Analyzer Implementing Bioluminescent Biosensors for Water Toxicity Assessment

    Directory of Open Access Journals (Sweden)

    Constantinos Georgiou

    2010-07-01

    Full Text Available This paper describes the development of an automated Flow Injection analyzer for water toxicity assessment. The analyzer is validated by assessing the toxicity of heavy metal (Pb2+, Hg2+ and Cu2+ solutions. One hundred μL of a Vibrio fischeri suspension are injected in a carrier solution containing different heavy metal concentrations. Biosensor cells are mixed with the toxic carrier solution in the mixing coil on the way to the detector. Response registered is % inhibition of biosensor bioluminescence due to heavy metal toxicity in comparison to that resulting by injecting the Vibrio fischeri suspension in deionised water. Carrier solutions of mercury showed higher toxicity than the other heavy metals, whereas all metals show concentration related levels of toxicity. The biosensor’s response to carrier solutions of different pHs was tested. Vibrio fischeri’s bioluminescence is promoted in the pH 5–10 range. Experiments indicate that the whole cell biosensor, as applied in the automated fluidic system, responds to various toxic solutions.

  17. Re-evaluation of a subsurface injection experiment for testing flow and transport models

    Energy Technology Data Exchange (ETDEWEB)

    Fayer, M.J.; Lewis, R.E.; Engelman, R.E.; Pearson, A.L.; Murray, C.J.; Smoot, J.L. Lu, A.H. [Pacific Northwest Lab., Richland, WA (United States); Randall, P.R. [Three Rivers Scientific, Richland, WA (United States); Wegener, W.H. [Hoquiam High School, Hoquiam, WA (United States)

    1995-12-01

    The current preferred method for disposal of low-level radioactive waste (LLW) at the Hanford Site is to vitrify the wastes so they can be stored in a near-surface, shallow-land burial facility (Shord 1995). Pacific Northwest Laboratory (PNL) managed the PNL Vitrification Technology Development (PVTD) Project to assist Westinghouse Hanford Company (WHC) in designing and assessing the performance of a disposal facility for the vitrified LLW. Vadose zone flow and transport models are recognized as necessary tools for baseline risk assessments of stored waste forms. The objective of the Controlled Field Testing task of the PVTD Project is to perform and analyze field experiments to demonstrate the appropriateness of conceptual models for the performance assessment. The most convincing way to demonstrate appropriateness is to show that the model can reproduce the movement of water and contaminants in the field. Before expensive new experiments are initiated, an injection experiment conducted at the Hanford Site in 1980 (designated the ``Sisson and the Lu experiment``) should be completely analyzed and understood. Briefly, in that test, a solution containing multiple tracers was injected at a single point into the subsurface sediments. The resulting spread of the water and tracers was monitored in wells surrounding the injection point. Given the advances in knowledge, computational capabilities, and models over the last 15 years, it is important to re-analyze the data before proceeding to other experiments and history-matching exercises.

  18. Spectrophotometric method for determination of sulfide with iron(III) and nitrilotriacetic acid by flow injection.

    Science.gov (United States)

    Kester, M D; Shiundu, P M; Wade, A P

    1992-03-01

    A manual colorimetric method for determination of sulfide has been adapted to flow injection, systematically optimized, and more fully characterized. Its intended application is for measurement of sodium sulfide reagent strength in pulp process streams, and sulfide contamination in effluent from Kraft pulp mills. In the flow-injection method developed, a sample solution containing sulfide is reacted with a mixture of iron(III) and nitrilotriacetic acid under ammoniacal conditions. The absorbance of the intensely-colored green product of this reaction is measured at 636 nm. Excess sulfite is present as a color stabilizer. A linear dynamic range of 20-100 ppm sulfide is readily achieved; the relative standard deviation is less than 1.2% (n = 10) throughout this range, and 0.37% (n = 10) midrange at 60 ppm. The usable dynamic range is 8-250 ppm sulfide. Long-term stability of the method is ensured by periodically performing an automatic cleaning cycle using a hydrochloric acid wash solution. This prevents tube discoloration and removes any precipitates which are formed under strongly alkaline conditions. The sample throuhput rate is at least 30/hr, given alternate acid wash cycles.

  19. Flow injection analysis of picric acid explosive using a copper electrode as electrochemical detector.

    Science.gov (United States)

    Junqueira, João R C; de Araujo, William R; Salles, Maiara O; Paixão, Thiago R L C

    2013-01-30

    A simple and fast electrochemical method for quantitative analysis of picric acid explosive (nitro-explosive) based on its electrochemical reduction at copper surfaces is reported. To achieve a higher sample throughput, the electrochemical sensor was adapted in a flow injection system. Under optimal experimental conditions, the peak current response increases linearly with picric acid concentration over the range of 20-300 μmol L(-1). The repeatability of the electrode response in the flow injection analysis (FIA) configuration was evaluated as 3% (n=10), and the detection limit of the method was estimated to be 6.0 μmol L(-1) (S/N=3). The sample throughput under optimised conditions was estimated to be 550 samples h(-1). Peroxide explosives like triacetone triperoxide (TATP) and hexamethylene triperoxide diamine (HMTD) were tested as potential interfering substances for the proposed method, and no significant interference by these explosives was noticed. The proposed method has interesting analytical parameters, environmental applications, and low cost compared with other electroanalytical methods that have been reported for the quantification of picric acid. Additionally, the possibility to develop an in situ device for the detection of picric acid using a disposable sensor was evaluated. Crown Copyright © 2012. Published by Elsevier B.V. All rights reserved.

  20. Theoretical considerations of Flow Injection Analysis in the Absence of Chemical Reactions

    DEFF Research Database (Denmark)

    Andersen, Jens Enevold Thaulov

    2000-01-01

    The fundamental mechanism of flow injection analysis (FIA) is assumed to be simple dissusion and the response of the detector is included in a model description that provide information about the shape of the FIA peak in terms of, basically, five parameters. Two of the five parameters are associa......The fundamental mechanism of flow injection analysis (FIA) is assumed to be simple dissusion and the response of the detector is included in a model description that provide information about the shape of the FIA peak in terms of, basically, five parameters. Two of the five parameters...... are associated with the compound while the rest yield information about the solvent and friction. By introducing a kinetic-diffusion coefficient, it is shown that the shape of the FIA peak is well described by the theory for diffusion of K3(Fe(CN)6), K2CrO4 and Ni(NO3)2 in distilled water. It is suggested...... that any deviation from the features of the present model and the results of a tentative chemical reaction with one of the test compounds, is related to chemical kinetics....

  1. Determination of water in organic solvents by flow-injection analysis with Karl Fischer reagent and a biamperometric detection system

    NARCIS (Netherlands)

    Liang, Chen; Vácha, Pavel; van der Linden, W.E.

    1988-01-01

    A flow-injection system with a biamperometric flow-through detector provided with two platinum plate electrodes was tested for the determination of water with a two-component pyridine-free Karl Fischer reagent. The response was shown to be linear in the concentration range 0.03–0.11% water in

  2. Development of flow injection method for indirect copper determination with amperometric detection in drinking water samples

    Directory of Open Access Journals (Sweden)

    Nikolić-Mandić Snežana

    2012-01-01

    Full Text Available A gas-diffusion flow injection method with amperometric detection for indirect copper determination on a silver electrode is developed. The flow through system is equipped with two injection valves and a gas-diffusion unit. In the first step, a signal of cyanide solution was recorded. In the following step a signal of cyanide in the presence of copper was measured. Interferences (Cd(II, Co(II, Ag(I, Ni(II, Fe(III, Hg(II and Zn(II were investigated and successfully removed. The calibration graph is linear in the range 1-90 μmol dm-3 of copper, correlation coefficient is 0.993, the regression equation is I = (0.0455±0.0015c + (0.4611±0.0671, I is relative signal decrease in μA and c is concentration in μmol dm-3. Relative standard deviation for six consecutive injections of 30 μmol dm-3 copper(II was 1.47 % and for 1 μmol dm-3 copper(II was 3.40 %. The detection limit, calculated as 3 s/m (where s is a standard deviation of nine measurement of a reagent blank and m is the slope of the calibration curve, was 0.32 μmol dm-3, which corresponds to 2.44 ng of copper(II (loop volume was 0.12 cm3. The method enables 60 analyses per hour and it was successfully applied on determination of copper in drinking water samples. [Acknowledgements. The authors acknowledge the grant from the Ministry of Education and Science of the Republic of Serbia, Project number 172051

  3. Transverse injection into Mach 2 flow behind a rearward-facing step - A 3-D, compressible flow test case for hypersonic combustor CFD validation

    Science.gov (United States)

    Mcdaniel, James C.; Fletcher, Douglas G.; Hartfield, Roy J.; Hollo, Steven D.

    1991-01-01

    A spatially-complete data set of the important primitive flow variables is presented for the complex, nonreacting, 3D unit combustor flow field employing transverse injection into a Mach 2 flow behind a rearward-facing step. A unique wind tunnel facility providing the capability for iodine seeding was built specifically for these measurements. Two optical techniques based on laser-induced-iodine fluorescence were developed and utilized for nonintrusive, in situ flow field measurements. LDA provided both mean and fluctuating velocity component measurements. A thermographic phosphor wall temperature measurement technique was developed and employed. Data from the 2D flow over a rearward-facing step and the complex 3D mixing flow with injection are reported.

  4. Flow injection analysis of nanomolar silicate using long pathlength absorbance spectroscopy.

    Science.gov (United States)

    Ma, Jian; Byrne, Robert H

    2012-01-15

    Determination of silicate at low concentrations (i.e., nanomolar levels) is an important analytical objective for both marine science and the semiconductor industry. Here we report the use of flow injection analysis (FIA) in combination with long pathlength liquid core waveguide (LCW) spectrometry to achieve detection limits for dissolved silica on the order of 10nM. Sample throughput for the simple, automated analytical apparatus used in this work is 12h(-1) at low levels of dissolved silica; this rate can be increased by a factor of three for higher (micromolar) levels of dissolved silica. The analytical protocol is based on the reaction of silicate with ammonium molybdate to form a yellow silicomolybdate complex, which is subsequently reduced to silicomolybdenum blue by ascorbic acid. Optimization of the FIA procedure included consideration of the compositions and concentrations of reagents, volume of the injection loop, flow rate conditions, and lengths of mixing coils. The interference by phosphate was examined and eliminated through addition of oxalic acid. The dissolved silica detection limit of 7.2nM in pure water is consistent with the strictest standard for the semiconductor industry, and the 9.0nM detection limit for seawater shows that this analytical method is also suitable for oligotrophic ocean waters. The targeted analytical range of 10nM to 5μM can be easily extended to higher concentrations without altering the experimental hardware-i.e., by simply changing flow rates or selecting alternative analytical wavelengths. Compared to previously published LCW-based spectrophotometric methods, this analytical system exhibits improved sensitivity, reduced sample consumption, and higher sample throughput. Copyright © 2011 Elsevier B.V. All rights reserved.

  5. Electronic micropipettor: A versatile fluid propulsion and injection device for micro-flow analysis

    Energy Technology Data Exchange (ETDEWEB)

    Daniel, Daniela [Instituto de Quimica, Universidade de Sao Paulo, Av. Prof. Lineu Prestes 748, 05508-000 Sao Paulo, SP (Brazil); Gutz, Ivano G.R. [Instituto de Quimica, Universidade de Sao Paulo, Av. Prof. Lineu Prestes 748, 05508-000 Sao Paulo, SP (Brazil)]. E-mail: gutz@iq.usp.br

    2006-07-07

    The shortage of ready to use small sized liquid propulsion and switching devices for microfluidic cells ({mu}-cell) is a bottleneck in the dissemination of micro-flow analysis ({mu}-FA), now that microfluidic electrochemical cells can be designed and assembled in any laboratory by thermal transfer of laser printed masks and CD-Rs. Microprocessor-controlled electronic pipettors, commercially available with minimum capacity of 10 {mu}L, represent a compromise solution between oversized peristaltic pumps and tiny 'on a chip' micropumps and valves. The versatility of the electronic pipette coupled with the {mu}-cell (13-{mu}m deep longitudinal channel) was demonstrated in three operation modes: SIA like, FIA like and direct injection analysis (DIA). Injections of 100 nL K{sub 4}Fe(China){sub 6} (0.1 mol L{sup -1} KCl) define a linear analytical curve (r = 0.999) in the range of 5 x 10{sup -7} to 1.0 x 10{sup -3} mol L{sup -1} for flow amperometry at a gold electrode potentiostated at 0.4 V versus Ag/AgCl. Methods for the amperometric {mu}-flow determination of promethazine (FIA like), dipyrone (SIA like) and chlorpromazine (DIA) in pharmaceutical formulations were developed and applied to real samples. Excellent linearity of analytical curves and high repeatability (R.S.D. < 3.0%) at the low picomole range was obtained and all results for real samples were in agreement with reference methods. The results reflect the stability and the reliability of the setups envisioned for the electronic pipette coupled with amperometric {mu}-cell and the validity of the {mu}-FA methods.

  6. Effects of Swirl Bubble Injection on Mass Transfer and Hydrodynamics for Bubbly Flow Reactors: A Concept Paper

    Directory of Open Access Journals (Sweden)

    Farooqi Ahmad Salam

    2017-01-01

    Full Text Available Bubble flow reactors (BFR are commonly used for various industrial processes in the field of oil and gas production, pharmaceutical industries, biochemical and environmental engineering etc. The operation and performance of these reactors rely heavily on a range of hydrodynamic parameters; prominent among them are geometric configurations including gas injection geometry, operating conditions, mass transfer etc. A huge body of literature is available to describe the optimum design and performance of bubbly flow reactors with conventional bubble injection. Attempts were made to modify gas injection for improved efficiency of BFR’s. However, here instead of modifying the geometry of the gas injection, an attempt has been made to generate swirl bubbles for gaining larger mass transfer between gas and liquid. Here an exceptionally well thought strategies have been used in our numerical simulations towards the design of swirl injection mechanism, whose paramount aspect is to inhibit the rotary liquid motion but facilitates the swirl movement for bubbles in nearly stationary liquid. Our comprehension here is that the swirl motion can strongly affect the performance of bubbly reactor by identifying the changes in hydrodynamic parameters as compared to the conventional bubbly flows. In order to achieve this bubbly flow, an experimental setup has been designed as well as computational fluid dynamic (CFD code was used with to highlight a provision of swirl bubble injection by rotating the sparger plate.

  7. Drag reduction via micro bubble injection in boundary layer of channel flows

    Energy Technology Data Exchange (ETDEWEB)

    Hassan, Y.A. [Texas A and M Univ., Dept. of Nuclear Engineering, College Station, Texas (United States)

    2004-07-01

    Full text of publication follows:Methods to reduce the drag in turbulent flows have been carried out for the past several decades. Reducing skin friction has obvious advantages through improvements in fuel economy, range (as in case of commercial ships and aircraft) or in peak speed (desirable in military or racing applications) and for less impact on the environment due to less fuel consumption. Recently, the reduction of turbulent friction between a solid surface and fluid by adding drag reducing additives has received increasing attention for saving power and reducing the pollution. Polymers and surfactants injections, wall oscillations, traveling waves, blowing and suction, and micro-bubble injection are examples among active additives. Riblets are an example of passive techniques to achieve drag reduction. However, a consensus about understanding the mechanism that governs this phenomenon has not been reached. In this paper, an investigation of turbulent structure modification of fully developed channel flow by micro-bubble injection close to the upper wall was studied. Two-dimensional velocity components at Reynolds number of 5128 based on the half height of the channel and bulk velocity were measured. The particle image velocimetry technique was utilized to obtain the two-dimensional velocity fields of the fluid and the micro-bubbles. Micro-bubbles with an average diameter of 30 {mu}m were injected into the buffer layer. Various values of void fractions were used to evaluate the effects of micro-bubbles concentration on the drag reduction. Modifications in the length and time scales were detected by calculating two-point correlation coefficients. Streamline length and time scales were increased. On the contrary, the normal length and time scales were decreased with the increase of the drag reduction. The presence of the micro-bubbles with low local concentration of 4% achieved 40% drag reduction. A decrease in the Reynolds stresses were achieved as the void

  8. Observation of plasma microwave emission during the injection of supersonic plasma flows into magnetic arch

    Science.gov (United States)

    Viktorov, Mikhail; Mansfeld, Dmitry; Vodopyanov, Alexander; Golubev, Sergey

    2017-10-01

    Understanding of the energy transfer mechanisms from supersonic plasma flow into the thermal energy of plasma, waves and accelerated particles in the environment of planetary bow shocks and interplanetary shocks have been topical for many decades. Almost all mechanisms of energy dissipation in collisionless shock waves end with microscopic processes involving wave-particle interactions. Excitation of plasma waves in electron cyclotron frequency range plays an important role in the dissipation of bulk flow energy across the Earth bow shock. In the present work, the process of plasma deceleration during the injection of supersonic plasma flow across the magnetic field of an arched configuration is experimentally demonstrated. Pulsed plasma microwave emission in the electron cyclotron frequency range is observed. It is shown that the frequency spectrum of plasma emission is determined by the position of the deceleration region in the magnetic field of the magnetic arc and its bandwidth is defined by the magnetic field inhomogeneity in the deceleration region. The observed emission can be related to the cyclotron mechanism of wave generation by non-equilibrium energetic electrons in the dense plasma, especially excitation of electron Bernstein waves. The work was supported by RFBR (Project No. 16-32-60056).

  9. Coronary CT angiography using low concentrated contrast media injected with high flow rates: Feasible in clinical practice.

    Science.gov (United States)

    Mihl, Casper; Kok, Madeleine; Wildberger, Joachim E; Altintas, Sibel; Labus, David; Nijssen, Estelle C; Hendriks, Babs M F; Kietselaer, Bas L J H; Das, Marco

    2015-11-01

    Aim of this study was to test the hypothesis that peak injection pressures and image quality using low concentrated contrast media (CM) (240 mg/mL) injected with high flow rates will be comparable to a standard injection protocol (CM: 300 mg/mL) in coronary computed tomographic angiography (CCTA). One hundred consecutive patients were scanned on a 2nd generation dual-source CT scanner. Group 1 (n=50) received prewarmed Iopromide 240 mg/mL at an injection rate of 9 mL/s, followed by a saline chaser. Group 2 (n=50) received the standard injection protocol: prewarmed Iopromide 300 mg/mL; flow rate: 7.2 mL/s. For both protocols, the iodine delivery rate (IDR, 2.16 gI/s) and the total iodine load (22.5 gI) were kept identical. Injection pressure (psi) was continuously monitored by a data acquisition program. Contrast enhancement was measured in the thoracic aorta and all proximal and distal coronary segments. Subjective and objective image quality was evaluated between both groups. No significant differences in peak injection pressures were found between both CM groups (121 ± 5.6 psi vs. 120 ± 5.3 psi, p=0.54). Flow rates of 9 mL/s were safely injected without any complications. No significant differences in contrast-to-noise ratio, signal-to-noise ratio and subjective image quality were found (all p>0.05). No significant differences in attenuation levels were found in the thoracic aorta and all segments of the coronary arteries (all p>0.05). Usage of low iodine concentration CM and injection with high flow rates is feasible. High flow rates (9 mL/s) of Iopromide 240 were safely injected without complications and should not be considered a drawback in clinical practice. No significant differences in peak pressure and image quality were found. This creates a doorway towards applicability of a broad variety in flow rates and IDRs and subsequently more individually tailored injection protocols. Copyright © 2015 Elsevier Ireland Ltd. All rights reserved.

  10. Spray Development, Flow Interactions and Wall Impingement in a Direct-Injection Spark-Ignition Engine

    OpenAIRE

    Aleiferis, PG; Serras-Pereira, J.; Richardson, D.; Wallace, S.

    2007-01-01

    Levels of liquid fuel impingement on in-cylinder surfaces in direct injection spark ignition engines have typically been higher than those in port-fuel injection engines due to in-cylinder injection and higher injection pressures. The result is typically an increase in the levels of un-burned hydrocarbons and smoke emissions which reduce the potential fuel economy benefits associated with direct injection engines. Although different injection strategies can be used to reduce these effects to ...

  11. A flow injection sampling resonance light scattering system for total protein determination in human serum

    Science.gov (United States)

    Dong, Lijun; Li, Ying; Zhang, Yaheng; Chen, Xingguo; Hu, Zhide

    2007-04-01

    A novel flow injection method with resonance light scattering detection was developed for the determination of total protein concentrations. This method is based on the enhancement of RLS signals from Methyl Blue (MB) by protein. The enhanced RLS intensities at 333 nm, in a pH 4.1 acidic aqueous solution, were proportional to the protein concentration over the range 2.0-37.3 and 1.0-36.0 μg ml -1 for human serum albumin (HSA) and bovine serum albumin (BSA), respectively. The corresponding limits of detection (3 σ) of 45 ng ml -1 for HSA and 80 ng ml -1 for BSA were attained. The method was successfully applied to the quantification of total proteins in human serum samples, the maximum relative error is less than 1% and the recovery is between 98% and 102%. The sample throughput was 60 h -1.

  12. Flow-injection biamperometric direct determination of calcium dobesilate in irreversible couple system.

    Science.gov (United States)

    Song, Jun-Feng; Chen, Jia-Quan

    2003-11-24

    A flow-injection biamperometric method for direct determination of calcium dobesilate had been proposed based on biamperometric detection for irreversible couple. The detection was realized by coupling the oxidation of dobesilate at one platinum wire electrode with the reduction of MnO(4)(-) at another one with the applied potential difference of 0 V between two platinum wire electrodes. Dobesilate was determined in the range of 4.0 x 10(-6) to 1.0 x 10(-4) M with the detection limit of 8.0 x 10(-7) M (S/N=3). The relative standard derivation of 1.7% was obtained for 24 successive determinations of 4.0 x 10(-5) M dobesilate. The proposed method had been shown to be sensitive, simple and rapid.

  13. Bienzymatic Biosensor for Rapid Detection of Aspartame by Flow Injection Analysis

    Directory of Open Access Journals (Sweden)

    Maria-Cristina Radulescu

    2014-01-01

    Full Text Available A rapid, simple and stable biosensor for aspartame detection was developed. Alcohol oxidase (AOX, carboxyl esterase (CaE and bovine serum albumin (BSA were immobilised with glutaraldehyde (GA onto screen-printed electrodes modified with cobalt-phthalocyanine (CoPC. The biosensor response was fast. The sample throughput using a flow injection analysis (FIA system was 40 h−1 with an RSD of 2.7%. The detection limits for both batch and FIA measurements were 0.1 µM for methanol and 0.2 µM for aspartame, respectively. The enzymatic biosensor was successfully applied for aspartame determination in different sample matrices/commercial products (liquid and solid samples without any pre-treatment step prior to measurement.

  14. Flow-injection chemiluminescence determination of tryptophan through its peroxidation and epoxidation by peroxynitrous acid.

    Science.gov (United States)

    Liang, Yao-Dong; Song, Jun-Feng

    2005-06-01

    A flow-injection chemiluminescence method for the determination of tryptophan was proposed, which was based on an intense chemiluminescence of tryptophan in hydrogen peroxide-nitrite-sulfuric acid medium. The chemiluminescence reaction was attributed to peroxidation and epoxidation of tryptophan by peroxynitrous acid, and subsequent decomposition of the formed dioxetane. The chemiluminescence intensity was linear with tryptophan in the range of 6.0 x 10(-7) to 3.0 x 10(-5)mol l(-1) and the limit of detection (S/N=3) was 1.8 x 10(-7)mol l(-1). The proposed method was applied to the analysis of tryptophan in pharmaceutical preparations and human serum.

  15. Spectrophotometric flow-injection determination of zinc in plant digests based on a spot test.

    Science.gov (United States)

    Dias, Ana Cristi B; Carneiro, Josiane M T; Zagatto, Elias A G

    2004-05-28

    A spot test was implemented in a flow-injection system for the spectrophotometric determination of zinc in digests of plant materials. It is based on the influence of Zn(2+) on the oxidation rate of 1-naphthylethylenediamine (NED) by hexacyanoferrate(III) under acidic conditions. In order to control the precipitate formation and to maintain the resulting suspension, a micellar medium was established by adding Triton X-100. The proposed system handles about 65 samples per hour, meaning 72mug NED and 9.0mg K(3)[Fe(CN)(6)] per determination. Baseline drift is usually 0.999, n=6) and detection limit was estimated as 0.2mgl(-1) Zn. Results are precise (R.S.D.<1%, n=10) and in agreement with flame atomic absorption spectrometry and with certified values of standard reference materials.

  16. Control of microbial activity by flow injection analysis during high cell density cultivation of Escherichia coli.

    Science.gov (United States)

    Ding, T; Bilitewski, U; Schmid, R D; Korz, D J; Sanders, E A

    1993-01-01

    The application of an automated flow injection analysis (FIA) system for on-line determination of microbial activity, during high cell density cultivations of Escherichia coli is reported. Based on a bioelectrochemical principle, the FIA method used a redox mediator (potassium hexacyanoferrate(III)) to facilitate electron transfer from the microorganisms to an electrochemical detector. Assays were carried out using a new sampling device which provided aseptic operation by use of a valve and chemical sterilisation. No sample dilution or pretreatment was necessary for biomass concentrations up to approx. 40 g l-1. The sample volume was 0.5 ml and the overall analysis time was 5 min. FIA signals were found to correlate well with the oxygen uptake rate (OUR). Changes in metabolic activity due to low substrate levels or high inhibitor concentrations in the cultivation medium became obvious from the FIA signals.

  17. Free-convection flow past a horizontal surface in a nanofluid with suction/injection

    Science.gov (United States)

    Adnan, Nurul Shahirah Mohd; Arifin, Norihan Md; Bachok, Norfifah; Nazar, Roslinda

    2017-08-01

    The present work deals with the steady free-convection boundary-layer flow past a horizontal permeable surface embedded in a porous medium filled with a nanofluid. The similarity transformation was applied to the governing equations to transform into a system of ordinary differential equations, which are then solved numerically using Runge-Kutta-Fehlberg fourth-fifth order (RKF45) method. Three types of nanoparticles which are titania (TiO2), alumina (Al2O3), and copper (Cu) in the based fluid of water are considered to investigate the effect of the nanoparticle volume fraction parameter, υ. Results are presented and discussed for the local Nusselt number, the surface velocity, the temperature profiles, and the velocity profile. It is found that the imposition of suction/injection has an impact on the velocity profiles and temperature profiles.

  18. Determination of Henry's law constants of phenols by pervaporation-flow injection analysis.

    Science.gov (United States)

    Sheikheldin, S Y; Cardwell, T J; Cattrall, R W; Luque de Castro, M D; Kolev, S D

    2001-01-01

    A novel dynamic nonequilibrium technique for the determination of Henry's law constant (HLC) of phenols based on pervaporation-flow injection (PFI) is described. A linear relationship between HLC and the amount of phenol measured by a detector in the acceptor line of a PFI system was demonstrated. This relationship was constructed using five frequently encountered phenols (phenol, 2,4-dimethylphenol, 2,4-dichlorophenol, 2-chlorophenol, and 2,3-dimethylphenol) and used for the determination of the HLC of three other phenols (2,4,6-trichlorophenol, 2-methylphenol, and 3-methylphenol). The HLC of all eight phenols were also determined by the single equilibrium static technique (SEST). Fairly good agreementwas observed between both techniques regarding the HLC of 2,4,6-trichlorophenol, 2-methylphenol, and 3-methylphenol. On the basis of the results obtained, it was concluded that the PFI technique offers considerable advantages over SEST in terms of precision, speed, labor intensity, and possibilities for automation.

  19. Dissipation on Steady MHD Marangoni Convection Flow over a Flat Surface with Suction and Injection

    Directory of Open Access Journals (Sweden)

    S. Mohammed Ibrahim

    2013-01-01

    Full Text Available The combined effects of radiation and mass transfer on a steady MHD two-dimensional Marangoni convection flow over a flat surface in presence of Joule heating and viscous dissipation under influence of suction and injection is studied numerically. The general governing partial differential equations are transformed into a set of nonlinear ordinary differential equations by using unique similarity transformation. Numerical solutions of the similarity equations are obtained using the Runge-Kutta method along with shooting technique. The effects of governing parameters on velocity, temperature, and concentration as well as interface velocity, the surface temperature gradient, and the surface concentration gradient were presented in graphical and tabular forms. Comparisons with previously published work are performed and the results are found to be in excellent agreement.

  20. Determination of hydrogen peroxide in reactor moderator solutions by flow injection analysis

    Energy Technology Data Exchange (ETDEWEB)

    Whitaker, M.J.

    1991-12-31

    A flow injection analysis (FIA) method for the determination of hydrogen peroxide in reactor moderator water was developed and installed at the Savannah River Site (SRS) Water Quality Laboratory. The technique has an analytical range of 0.10 to 2.50 ppm (ug/mL) with a sampling rate of 40 samples per hour. The calibration curve is linear with a correlation coefficient of 0.999, and the precision is excellent with relative standard deviations at the 0.50% level for both 0.10 and 2.50 ppm standards. When the automated FIA procedure is compared to the manual method it demonstrates a twenty minute reduction in analysis time per sample, and the total liquid waste generated per sample analyzed is reduced by roughly 95 mL. 6 refs., 10 figs., 6 tabs.

  1. Determination of hydrogen peroxide in reactor moderator solutions by flow injection analysis

    Energy Technology Data Exchange (ETDEWEB)

    Whitaker, M.J.

    1991-01-01

    A flow injection analysis (FIA) method for the determination of hydrogen peroxide in reactor moderator water was developed and installed at the Savannah River Site (SRS) Water Quality Laboratory. The technique has an analytical range of 0.10 to 2.50 ppm (ug/mL) with a sampling rate of 40 samples per hour. The calibration curve is linear with a correlation coefficient of 0.999, and the precision is excellent with relative standard deviations at the 0.50% level for both 0.10 and 2.50 ppm standards. When the automated FIA procedure is compared to the manual method it demonstrates a twenty minute reduction in analysis time per sample, and the total liquid waste generated per sample analyzed is reduced by roughly 95 mL. 6 refs., 10 figs., 6 tabs.

  2. Differentiating organic from conventional peppermints using chromatographic and flow injection mass spectrometric (FIMS) fingerprints.

    Science.gov (United States)

    Gao, Boyan; Lu, Yingjian; Qin, Fang; Chen, Pei; Shi, Haiming; Charles, Denys; Yu, Liangli Lucy

    2012-12-05

    High-performance liquid chromatography (HPLC) and flow injection mass spectrometric (FIMS) fingerprinting techniques were tested for their potential in differentiating organic and conventional peppermint samples. Ten organic and ten conventional peppermint samples were examined using HPLC-UV and FIMS methods. Principal component analysis (PCA) showed that both HPLC and FIMS fingerprints could determine the difference in the commercial organic and conventional peppermints. FIMS fingerprinting provided a rapid test to differentiate organic and conventional peppermints in 1 min of analysis and has potential for high-throughput applications. On the other hand, HPLC fingerprints provide more information about the chemical composition of the samples, but take a longer time to differentiate organic and conventional peppermint samples.

  3. Flow structure of conical distributed multiple gas jets injected into a water chamber

    Energy Technology Data Exchange (ETDEWEB)

    Zhao, Jiajun; Yu, Yonggang [Nanjing University of Science and Technology, Nanjing (China)

    2017-04-15

    Based on an underwater gun firing project, a mock bullet with several holes on the head was designed and experimented to observe the combustion gas injected into a cylindrical water chamber through this mock bullet. The combustion gas jets contain one vertical central jet and 4 to 8 slant lateral jets. A high speed camera system was used to record the expansion of gas jets in the experimental study. In numerical simulations, the Euler two-fluid model and volume of fluid method were adopted to describe the gas-liquid flow. The results show the backflow zone in lateral jet is the main factor influencing the gas-liquid turbulent mixing in downstream. On cross sections, the gas volume fraction increased with time but the growth rate decreased. With a change of nozzle structure, the gas fraction was more affected than the shock structure.

  4. Flow injection spectrophotometric determination of ultra trace amounts of oxalic acid.

    Science.gov (United States)

    Ensafi, A A; Kazemzadeh, A

    2000-07-01

    A new simple, sensitive and rapid catalytic-spectrophotometric method for the determination of oxalic acid has been described based on its catalytic effect on the redox reaction between dichromate and Brilliant cresyl blue in acidic media by means of a flow injection analysis method. The color change of Brilliant cresyl blue due to its oxidation was monitored spectrophotometrically at 625 nm. The calibration graph was linear in the range of 0.020-4.70 microg/mL oxalic acid with a limit of detection 0.005 microg/mL of oxalic acid. The relative standard deviation for ten replicate measurements of 0.020 microg/mL and 0.900 microg/mL was 2.2% and 1.7%, respectively. No serious interference was identified. Oxalic acid was determined in wastewater and in spinach by the proposed method with satisfactory results.

  5. Chemiluminescence determination of potassium bromate in flour based on flow injection analysis.

    Science.gov (United States)

    Yan, Zhengyu; Zhang, Zhengwei; Yu, Yan; Liu, Zhen; Chen, Jianqiu

    2016-01-01

    A novel and highly sensitive flow-injection chemiluminescence method for the determination of potassium bromate (KBrO3) has been developed. This method is based on the luminescence properties of the KBrO3-Na2SO3-quinine sulfate system in acid medium. Optimized experimental conditions and a possible mechanism were investigated. The relative chemiluminescence intensity responded linearly to the concentration of KBrO3 in the range of 7.054 × 10(-6)-1.008 × 10(-4) mol/L with a detection limit of 2.116 × 10(-6) mol/L. The relative standard deviation (RSD) at 5.0 × 10(-5) mol/L KBrO3 (n = 12) was 2.3%. The proposed method was applied successfully to the determination of KBrO3 in flour. Copyright © 2015 Elsevier Ltd. All rights reserved.

  6. Determination of Picogram Levels of Diacerein in a Pharmaceutical Formulation by Flow-Injection Chemiluminescence

    Directory of Open Access Journals (Sweden)

    Gao Suya

    2017-01-01

    Full Text Available A simple, sensitive and inexpensive method for determination of diacerein by flow-injection chemiluminescence was proposed, based on the quenching effect of diacerein on the luminol-protein (bovine serum albumin, BSA reaction. It was found that the decrement of CL intensity was linearly proportional to the logarithm of diacerein concentration ranging from 5.0 to 7.0×103 pg·mL-1 (r = 0.9968, with the limit of detection (LOD of 1.0 pg·mL-1 (3σ. The proposed procedure was successfully applied to the determination of diacerein in pharmaceutical formulation, human saliva, and serum samples without interference from its potential impurities, with the recoveries ranging from 96.4% to 104.0% and the relative standard deviations (RSDs less than 4.0% (n=6.

  7. Potentiometric determination of total nitrogen in soils by flow injection analysis with a gas-diffusion unit

    OpenAIRE

    Ferreira, Alexandra M. R.; José L. F. C. Lima; Rangel,António O. S. S.

    1996-01-01

    A flow injection analysis (FIA) system incorporating a gas-diffusion unit and a potentiometric detector was developed for the determination of total nitrogen in soil digests. The solutions obtained from the Kjeldahl digestion of the soil samples were injected in the FIA system where ammonium was converted into ammonia. This gas diffused through a gas-permeable membrane to a buffer acceptor stream, allowing the separation of the gas from the rest of the sample. Once in contact with the buffer ...

  8. Data model for the elimination of matrix effects in enzyme-based flow-injection systems.

    Science.gov (United States)

    Becker, T M; Schmidt, H L

    2000-08-20

    This contribution presents a new conceptional enzyme-based flow injection analysis (FIA) system for the process and quality control of food processing and biotechnological systems. It provides the determination of different analytes in distinct process media on the base of a common experimental set-up. In contrast to known comparable systems, analysis is performed without the commonly used sample preparation and dilution steps. Instead, the adaptation to the necessary measurement range is realized by optimization of intrinsic system parameters. The central principle of the work presented is the elimination of occurring interferences by the heterogeneous matrix of the process sample. Based on a particular injection mode, the application of dehydrogenases as indicator enzymes and a specially developed data model using cognitive methods, cross sensitivities of the detector as well as disturbed reaction rates of the enzymes could be almost completely compensated. Two applications are presented, the analysis of ethanol in non-alcoholic beer and the online determination of D-/L-lactate during a lactic acid fermentation, which reveal the advantage of the developed system. Copyright 2000 John Wiley & Sons, Inc.

  9. Flow injection spectrophotometry using natural reagent from Morinda citrifolia root for determination of aluminium in tea.

    Science.gov (United States)

    Tontrong, Sopa; Khonyoung, Supada; Jakmunee, Jaroon

    2012-05-01

    A flow injection (FI) spectrophotometric method with using natural reagent extracted from Morinda citrifolia root has been developed for determination of aluminium. The extract contained anthraquinone compounds which could react with Al(3+) to form reddish complexes which had maximum absorption wavelength at 499.0nm. The extract could be used as a reagent in FI system without further purification to obtain pure compound. A sensitive method for determination of aluminium in concentration range of 0.1-1.0mgL(-1), with detection limit of 0.05mgL(-1) was achieved. Relative standard deviations of 1.2% and 1.7% were obtained for the determination of 0.1 and 0.6mgL(-1) Al(3+) (n=11). Sample throughput of 35h(-1) was achieved with the consumption of 3mL each of carrier and reagent solutions per injection. The developed method was successfully applied to tea samples, validated by the FAAS standard method. The method is simple, fast, economical and could be classified as a greener analytical method. Copyright © 2011 Elsevier Ltd. All rights reserved.

  10. DPPH·-luminol chemiluminescence system and its application in the determination of scutellarin in pharmaceutical injections and rat plasma with flow injection analysis.

    Science.gov (United States)

    Yao, Hong; Huang, Xiaomei; Shi, Peiying; Lin, Zhen; Zhu, Meilan; Liu, Ailin; Lin, Xinhua; Tang, Yuhai

    2017-06-01

    In this article, a DPPH·-luminol chemiluminescence (CL) system was reported and the CL mechanism was discussed according to the CL kinetic properties after sequence injecting DPPH· into the DPPH·-luminol reaction mixture. It was observed that scutellarin could inhibit the CL response of the DPPH·-luminol system. Based on this observation, a simple and rapid flow injection CL method was developed for the determination of scutellarin using the inhibition effect in alkaline medium. The optimized chemical conditions for the CL reaction were 5 × 10(-6)  mol/L DPPH· and 1.0 × 10(-4)  mol/L luminol in 0.01 mol/L NaOH. Under optimized conditions, the CL intensity was inversely proportional to the concentration of scutellarin over the ranges 5-2000 and 40-3200 ng/ml in pharmaceutical injection and rat plasma, respectively. The limits of detection (S/N = 3) were 5 and 40 ng/ml in preparations and rat plasma, respectively. Furthermore, the precision, recovery and stability of the validated method were acceptable for the determination of scutellarin in both pharmaceutical injections and rat plasma. The presented method was successfully applied in the determination of scutellarin in pharmaceutical injections and real rat plasma samples. Copyright © 2016 John Wiley & Sons, Ltd.

  11. Espectrofotometria de zinco em fertilizantes em fluxo Flow injection spectrophotometry of zinc in mineral fertilizers

    Directory of Open Access Journals (Sweden)

    Arnaldo Antonio Rodella

    1999-07-01

    Full Text Available Um sistema de análise química por injeção em fluxo é proposto para a determinação espectrofotométrica de zinco em amostras de misturas de fertilizantes minerais, empregando-se zincon como reagente cromogênico. O procedimento analítico envolve redução de íons metálicos por ácido ascórbico, complexação com íon cianeto, seguindo-se a descomplexação seletiva do zinco com formaldeído, liberando-o para que reaja com o zincon formando um complexo azul. A aplicação do método proposto à extratos de mistura de fertilizantes indicou que a ação de interferentes pode ser contornada e que resultados comparáveis aos da espectrometria de absorção atômica são obtidos.A flow injection system for zinc analysis in mineral fertilizer mixtures is proposed using zincon as chromogenic reagent. The effect of interfering ions such as Cu2+, Fe3+, Mn2+ was eliminated by reduction (using ascorbic acid and complexation of these metal íons with cyanide, with zinc included. Zinc is allowed to react with zincon only after the destruction of the zinc cyano complex with formaldehyde. Flow injection analysis permitted efficient control of the reaction time so that only the zinc ion is set free to produce a blue complex with zincon. Zinc was determined in 16 fertilizer mixtures (3 replicates with precision and accuracy comparable to atomic absorption spectrometry.

  12. Use of flow injection mass spectrometric fingerprinting and chemometrics for differentiation of three black cohosh species

    Energy Technology Data Exchange (ETDEWEB)

    Huang, Huilian [Food Composition and Methods Development Laboratory, Beltsville Human Nutrition Research Center, Agricultural Research Service, U.S. Department of Agriculture, Beltsville, MD (United States); Key Laboratory of Modern Preparation of TCM, Jiangxi University of Traditional Chinese Medicine, Ministry of Education, Nanchang, Jiangxi Province (China); Sun, Jianghao [Food Composition and Methods Development Laboratory, Beltsville Human Nutrition Research Center, Agricultural Research Service, U.S. Department of Agriculture, Beltsville, MD (United States); McCoy, Joe-Ann [The North Carolina Arboretum Germplasm Repository, UNC Affiliate Campus, Asheville, NC (United States); Zhong, Haiyan [College of Food Science and Engineering, Central South University of Forestry and Technology, Changsha, Hunan Province (China); Fletcher, Edward J. [Strategic Sourcing, Inc., Banner Elk, NC 28604 (United States); Harnly, James, E-mail: harnly.james@ars.usda.gov [Food Composition and Methods Development Laboratory, Beltsville Human Nutrition Research Center, Agricultural Research Service, U.S. Department of Agriculture, Beltsville, MD (United States); Chen, Pei, E-mail: pei.chen@ars.usda.gov [Food Composition and Methods Development Laboratory, Beltsville Human Nutrition Research Center, Agricultural Research Service, U.S. Department of Agriculture, Beltsville, MD (United States)

    2015-03-01

    Flow injection mass spectrometry (FIMS) was used to provide chemical fingerprints of black cohosh (Actaea racemosa L.) in a manner of minutes by omitting the separation step. This method has proven to be a powerful tool for botanical authentication and in this study it was used to distinguish between three Actaea species prior to a more detailed chemical analysis using ultra high-performance liquid chromatography high-resolution mass spectrometry (UHPLC–HRMS). Black cohosh has become increasingly popular as a dietary supplement in the United States for the treatment of symptoms related to menopause. However, it has been known to be adulterated with the Asian Actaea dahurica (Turcz. ex Fisch. & C.A.Mey.) Franch. species (syn. Cimicifuga dahurica (Turcz.) Maxim). Existing methods for identification of black cohosh and differentiation of Actaea species are usually lengthy, laborious, and lack robustness, often based on the comparison of a few pre-selected components. Chemical fingerprints were obtained for 77 black cohosh samples and their related species using FIMS in the negative ion mode. The analysis time for each sample was less than 2 min. All data were processed using principal component analysis (PCA). FIMS fingerprints could readily differentiate all three species. Representative samples from each of the three species were further examined using UHPLC–MS to provide detailed profiles of the chemical differences between the three species and were compared to the PCA loadings. This study demonstrates a simple, fast, and easy analytical method that can be used to differentiate A. racemosa, Actaea podocarpa, and A. dahurica. - Highlights: • Flow injection mass spectrometry (FIMS) was used to provide chemical fingerprints of black cohosh (Actaea racemosa L.) in a manner of minutes by omitting the separation step. • FIMS can discriminate between A. dahurica, A. podocarpa, and A. racemosa. • FIMS is a valuable screening tool for authentication of botanicals.

  13. The impact of flow injection on modem chemical analysis: has it fulfilled our expectations? And where are we going?

    DEFF Research Database (Denmark)

    Hansen, Elo Harald

    2004-01-01

    Presenting a condensation of the opening lecture of the 12th ICFIA conference, this communication presents a view of the impact that flow injection analysis (FIA) has had on modern analytical chemistry, evaluated both within the academic community and outside it, i.e., in “industry”. The ensuing...... developments of FIA, encompassing sequential injection analysis (SIA) and bead injection lab-on-valve (BI-LOV), are described and their individual features discussed. Finally some recent results of the activities from the author’s own research group are briefly mentioned....

  14. Performance of 4600-pound-thrust centrifugal-flow-type turbojet engine with water-alcohol injection at inlet

    Science.gov (United States)

    Glasser, Philip W

    1950-01-01

    An experimental investigation of the effects of injecting a water-alcohol mixture of 2:1 at the compressor inlet of a centrifugal-flow type turbojet engine was conducted in an altitude test chamber at static sea-level conditions and at an altitude of 20,000 feet with a flight Mach number of 0.78 with an engine operating at rated speed. The net thrust was augmented by 0.16 for both flight conditions with a ratio of injected liquid to air flow of 0.05. Further increases in the liquid-air ratio did not give comparable increases in thrust.

  15. Separation and preconcentration by flow injection coupled to tungsten coil electrothermal atomic absorption spectrometry

    Science.gov (United States)

    Silva, Márcia M.; Krug, Francisco J.; Oliveira, Pedro V.; Nóbrega, Joaquim A.; Reis, Boaventura F.; Penteado, Daniel A. G.

    1996-12-01

    A flow injection system coupled to a tungsten coil electrothermal atomizer has been developed for on-line separation and preconcentration, using lead as a model element. The system utilizes three-way solenoid valves for sampling, buffering, washing and reconditioning solution management, and the resin column is inserted in the tip of the autosampler arm of a Varian GTA-96. The solenoid valves and tungsten coil power supply were controlled by a computer program written in Visual Basic, interfaced with the built-in Varian software. The system performance was tested by loading the resin column with the sample flowing at 3 ml min -1 for 60 s. Elution was performed automatically by sampling 20 μl of the eluent from a sample cup of the autosampler, and this aliquot was delivered into a 150 W tungsten coil. With Chelex-100 resin, the separation of concomitants was tested with lead in the presence of as much as 1000 mg l -1 of Ca, Mg, Na or K. The model system presented an enrichment factor of 64 at a sampling rate of 30 samples per hour.

  16. Multicommuted flow system for the determination of glucose in animal blood serum exploiting enzymatic reaction and chemiluminescence detection

    OpenAIRE

    Pires,Cherrine K.; Martelli,Patrícia B.; Reis, Boaventura F.; Lima, José L. F. C.; Saraiva, Maria Lúcia M. F. S.

    2003-01-01

    An automatic flow procedure based on multicommutation dedicated for the determination of glucose in animal blood serum using glucose oxidase with chemiluminescence detection is described. The flow manifold consisted of a set of three-way solenoid valves assembled to implement multicommutation. A microcomputer furnished with an electronic interface and software written in Quick BASIC 4.5 controlled the manifold and performed data acquisition. Glucose oxidase was immobilized on porous silica be...

  17. Very-high-flow injection rate for upper abdominal CT angiography

    Energy Technology Data Exchange (ETDEWEB)

    Kimura, Masashi; Minamiguti, Hiroki; Hagihira, Takami; Kishi, Kazushi; Sato, Morio [Wakayama Medical Coll. (Japan); Shioyama, Yasukazu; Okumura, Toshiyuki; Yamada, Kouji; Kawashima, Michihisa [Central Hospital and Cancer Center of Ibaraki Prefecture, Tomobe (Japan)

    2002-06-01

    The purpose of this study was to compare a very-high-flow injection-rate method (group A) and a conventional injection-rate method (group B) for visualization of upper abdominal arteries by multidetector helical computed tomography (MDHCT). The subjects were 240 patients suspected to have abdominal lesions. They were randomly assigned to group A (120 patients) and group B (120 patients). In group A, the bilateral medial cubital veins were punctured, and contrast medium was infused at a rate of 8.6-9.6 ml/s. In group B, the unilateral medial cubital vein was punctured, and contrast medium was infused at a rate of 2.0-3.0 ml/s. The quality of vascular visualization was graded as poor, good, or excellent by three radiologists. All visualizations of the celiac trunk (CE) and superior mesenteric artery (SMA) were graded as excellent in both group A and group B. Visualization grades of the subsegmental branches of the hepatic artery (HA), right gastric artery (RGA), cystic artery, dorsal pancreatic artery (DPA), and superior pancreaticoduodenal artery (SPDA) were good or excellent in 75% (paging method)/53.3% (three-dimensional method), 85%/30%, 77.7%/18.3%, 76.7%/28.3%, and 88.3%/42.5%, respectively, in group A, and 33.3%/11.7%, 46.7%/3.4%, 41.6%/5%, 55%/4.2%, and 72.5%/14.2%, respectively, in group B. The appearance rate of intrahepatic portal branches was 28.3% in group A and 66.7% in group B in the arterial dominant phase. Group A showed better visualization results than Group B in upper abdominal arteries according to MDHCT. (author)

  18. Use of flow injection and sequential injection analysis schemes for the determination of trace-level concentrations of metals in complex matrices by ETAAS and ICPMS

    DEFF Research Database (Denmark)

    Hansen, Elo Harald

    2005-01-01

    to facilitate the desired sensitivity and selectivity of measurement. Such pretreatment schemes are advantageously performed in flow injection (FI) or sequential injection (SI) manifolds, where all unit operations can be effected on-line and under enclosed and strictly controlled conditions. Various separation...... and characteristics of FI and SI, we present, via selected examples, various separation/preconcentration FI/Sl schemes for the determination of trace levels of metals, with particular emphasis on the use of the novel extension of FI/SI, that is, the so-called lab-on-valve concept.......Despite their excellent analytical chemical capacities for determination of low levels of metal species, electrothermal atomic absorption spectrometry and inductively coupled plasma mass spectrometry often require suitable pretreatment (separation and preconcentration) of the sample material...

  19. Enhancement of peroxyoxalate chemiluminescence by copper (II) in flow-injection analysis: optimization by factorial design analysis.

    NARCIS (Netherlands)

    Steijger, O.M.; den Nieuwenboer, H.C.M.; Lingeman, H.; Brinkman, U.A.T.; Holthuis, J.J.M.; Smilde, A.K.

    1996-01-01

    A flow injection analysis (FIA) system with peroxyoxalate chemiluminescence (CL) detection was optimized by factorial design analysis in the absence and presence of Cu(II) ions. The carrier stream was a mixture of acetonitrile and an aqueous imidazole solution of pH 7.0. The effect of the metal ions

  20. Introduction of Hydrogen Peroxide as an Oxidant in Flow Injection Analysis: Speciation of Cr(III) and Cr(VI)

    DEFF Research Database (Denmark)

    Andersen, Jens Enevold Thaulov

    1998-01-01

    Hydrogen peroxide was used as an oxidant in Flow Injection Analysis (FIA). The formation of gaseous components during the analysis was suppressed by maintaining a concentration lower than 0.15% of hydrogen peroxide in 0.1 M NaOH. By this method Cr(III) was oxidised on-line to Cr(VI) which...

  1. Flow injection on-line preconcentration of low levels of Cr(VI) with detection by ETAAS

    DEFF Research Database (Denmark)

    Som-aum, Waraporn; Liawruangrath, Saisunee; Hansen, Elo Harald

    2002-01-01

    A flow injection (FI) on-line sorption preconcentration procedure utilizing a packed column reactor and combined with electrothermal atomic absorption spectrometry (ETAAS) is proposed for the determination of low levels of Cr(VI) in water samples. Polytetrafluoroethylene (PTFE) beads packed...

  2. Exploiting the bead-injection approach in the integrated sequential injection Lab-on-Valve format using hydrophobic packing materials for on-line matrix removal and preconcentration of trace levels of cadmium in environmental and biological samples via formation of non-charged chelates prior to ETAAS detection

    DEFF Research Database (Denmark)

    Miró, Manuel; Jonczyk, Sylwia; Wang, Jianhua

    2003-01-01

    The concept of renewable microcolumns within the conduits of an automated single injection lab-on-valve system was exploited in a sorption/elution fashion using sorbents of hydrophobic nature. The scheme's practical applicability was demonstrated for the electrothermal atomic absorption...... spectrometry determination of trace level concentrations of cadmium in complex matrices. Statistical comparisons between the proposed procedure and certified values revealed no significant differences at the 95% confidence level....

  3. Single bolus intravenous regadenoson injection versus central venous infusion of adenosine for maximum coronary hyperaemia in fractional flow reserve measurement.

    Science.gov (United States)

    van Nunen, Lokien X; Lenders, Guy D; Schampaert, Stéphanie; van 't Veer, Marcel; Wijnbergen, Inge; Brueren, Guus R G; Tonino, Pim A L; Pijls, Nico H J

    2015-12-01

    The aim of this study was to compare the hyperaemic effect of a single bolus regadenoson injection to a central venous adenosine infusion for inducing hyperaemia in the measurement of fractional flow reserve (FFR). One hundred patients scheduled for FFR measurement were enrolled. FFR was first measured by IV adenosine (140 µg/kg/min), thereafter by IV bolus regadenoson injection (400 µg), followed by another measurement by IV adenosine and bolus injection of regadenoson. The regadenoson injections were randomised to central or peripheral intravenous. Hyperaemic response and duration of steady state maximum hyperaemia were studied, central versus peripheral venous regadenoson injections were compared, and safety and reproducibility of repeated injections were investigated. Mean age was 66±8 years, 75% of the patients were male. The target stenosis was located in the LM, LAD, LCX, and RCA in 7%, 54%, 20% and 19%, respectively. There was no difference in FFR measured by adenosine or by regadenoson (ΔFFR=0.00±0.01, r=0.994, pregadenoson was variable (10-600 s). No serious side effects of either drug were observed. Maximum coronary hyperaemia can be achieved easily, rapidly, and safely by one single intravenous bolus of regadenoson administered either centrally or peripherally. Repeated regadenoson injections are safe. The hyperaemic plateau is variable. Clinical Trial Registration: http://clinicaltrials.gov/ct2/ show/study/NCT01809743?term=NCT01809743&rank=1 (ClinicalTrials.gov Identifier: NCT01809743).

  4. Multiphase contrast-saline mixture injection with dual-flow in 64-row MDCT coronary CTA.

    Science.gov (United States)

    Cao, Lizhen; Du, Xiangying; Li, Pengyu; Liu, Yaou; Li, Kuncheng

    2009-03-01

    To explore the feasibility of multiphase contrast-saline mixture with dual-flow injection technique for visualization of right ventricular (RV) cavity and interventricular septum (IVS) in 64-row multidetector computed tomography (MDCT) coronary angiography. Twenty-four patients underwent coronary CT angiography (CTA) imaging with 64-row MDCT. In twelve patients (group A), 60 ml contrast medium (CM) bolus was followed by 40 ml saline, and in the other twelve patients (group B), 50 ml CM bolus was followed by 50 ml contrast-saline mixture at 60:40 ratio. The CM, saline and contrast-saline mixture flow rate were all 5.0 ml/s. Two experienced radiologists measured the CT values of ascending aorta, descending aorta, pulmonary artery and RV, rated the uniformity of RV cavity, the visualization of coronary arteries and IVS independently. By Kappa test, agreement between the two radiologists was 0.93 and 0.86 concerning the CT value measurements and the grades of the three indexes, respectively. By t-test, the mean CT values of ascending aorta and descending aorta of the two groups had no statistical difference (t=1.459, P>0.05; t=1.619, P>0.05); while the mean CT values of pulmonary artery and RV cavity had statistical differences (t=8.316, P0.05; U=54.00, P>0.05); while according to the visualization of IVS, group B was better than group A (U=8.00, P<0.05). In coronary CTA, a contrast-saline mixture after CM bolus can provide clear visualization of RV and IVS and LV without impairing coronary CTA image.

  5. Pharmacokinetic of pseudoephedrine in rat serum with luminol-pepsin chemiluminescence system by flow injection analysis.

    Science.gov (United States)

    Luo, Kai; Li, Yajuan; Zheng, Xiaohui; Song, Zhenghua

    2015-02-01

    Pepsin (Pep) accelerated the electron transferring rate of excited 3-aminophathlate and enhanced luminol-dissolved oxygen chemiluminescence (CL) intensity, and the flow injection (FI) luminol-Pep CL system was first developed. It was found that the CL intensity of luminol-Pep reaction could be remarkably inhibited by pseudoephedrine (PE); the decrement of CL intensity was linear to the logarithm of PE concentration in the range of 0.1∼100.0 nmol L(-1) with a detection limit of 0.03 nmol mL(-1) (3σ). At a flow rate of 2.0 mL min(-1), the complete process including washing and sampling was performed within 40 s, offering a sample throughput of 90 h(-1). This proposed method was successfully applied to determining PE in rat serum for 18 h after intragastric administration with the elimination ratio of 42.34 % and recoveries from 90.3 to 110.6 %. The pharmacokinetic results showed that PE could be rapidly absorbed into serum with peak concentration (C max) of 1.45 ± 0.18 g L(-1) at the time (T max) of 1.49 ± 0.02 h; the absorption half-life (0.35 ± 0.04 h), elimination half-life (1.86 ± 0.24 h), the area under curve (109.81 ± 6.03 mg L(-1) h(-1)), mean residence time (3.82 ± 0.27 h), and elimination rate constant (2.26 ± 0.23 L g(-1) h(-1)) in rats vivo were derived, respectively. The possible CL mechanism of luminol-Pep-PE reaction was discussed by FI-CL, fluorescence, and molecular docking (MD) methods.

  6. Flow structures in a lean-premixed swirl-stabilized combustor with microjet air injection

    KAUST Repository

    LaBry, Zachary A.

    2011-01-01

    The major challenge facing the development of low-emission combustors is combustion instability. By lowering flame temperatures, lean-premixed combustion has the potential to nearly eliminate emissions of thermally generated nitric oxides, but the chamber acoustics and heat release rate are highly susceptible to coupling in ways that lead to sustained, high-amplitude pressure oscillations, known as combustion instability. At different operating conditions, different modes of instability are observed, corresponding to particular flame shapes and resonant acoustic modes. Here we show that in a swirl-stabilized combustor, these instability modes also correspond to particular interactions between the flame and the inner recirculation zone. Two stable and two unstable modes are examined. At lean equivalence ratios, a stable conical flame anchors on the upstream edge of the inner recirculation zone and extends several diameters downstream along the wall. At higher equivalence ratios, with the injection of counter-swirling microjet air flow, another stable flame is observed. This flame is anchored along the upstream edge of a stronger recirculation zone, extending less than one diameter downstream along the wall. Without the microjets, a stationary instability coupled to the 1/4 wave mode of the combustor shows weak velocity oscillations and a stable configuration of the inner and outer recirculation zones. Another instability, coupled to the 3/4 wave mode of the combustor, exhibits periodic vortex breakdown in which the core flow alternates between a columnar mode and a vortex breakdown mode. © 2010 Published by Elsevier Inc. on behalf of The Combustion Institute. All rights reserved.

  7. Redefining Exploitation

    DEFF Research Database (Denmark)

    Agarwala, Rina

    2016-01-01

    -employed workers are organizing as workers. They are fighting labor exploitation by redefining the concept to include additional exploitation axes (from the state and middle class) and forms (including sexual). In doing so, they are redefining potential solutions, including identities and material benefits, to fit...... their unique needs. By expanding the category of “workers” beyond those defined by a narrow focus on a standard employer-employee relationship, these movements are also fighting exclusion from earlier labor protections by increasing the number of entitled beneficiaries. These struggles provide an important...

  8. Flow injection analysis with tubular membrane ion-selective electrode and coated wires for buspirone hydrochloride.

    Science.gov (United States)

    Abdel-Ghani, Nour; Issa, Yousry; Shoukry, Adel; Ahmed, Howayda

    2007-01-01

    New Plastic membrane ion-selective electrode for buspirone hydrochloride based on buspironium tetraphenylborate was prepared. The electrode exhibited mean slope of calibration graph of 58.4 mV per decade of BusCl concentration at 25 degrees C. The electrode can be used within the concentration range 6.3 x 10(-5) - 10(-2) M BusCl at a pH range of 2.5-7.0. The standard electrode potentials were determined at different temperatures and used to calculate the isothermal temperature coefficient of the electrode, amounting to 0.00056 V degrees C(-1). The electrode showed a very good selectivity for BusCl with respect to a number of inorganic cations, sugars and amino acids. The electrode was applied to the potentiometric determination of the buspirone ion and its pharmaceutical preparation under batch and flow injection conditions. Also, buspirone was determined by conductimetric titrations. Graphite rod, copper and silver coated wire electrodes were prepared and characterized as sensors for the drug under investigation.

  9. Flow injection determination of ketotifen fumarate using PVC membrane selective electrodes.

    Science.gov (United States)

    Khater, M M; Issa, Y M; Mohammed, Sabrein H

    2009-11-01

    In this study a PVC membrane electrode for determination of ketotifen fumarate is reported, where ketotifen tetraphenylborate (Keto-TPB) was used as ion exchanger. The electrode has linear range of 5.6x10(-6)-1.0x10(-2) and 1.0x10(-5)-1.0x10(-2) mol/L, with detection limits 2.37x10(-6)and 4.60x10(-6) mol/L in batch and flow injection analysis (FIA), respectively. The electrodes show a Nernstian slope value (58.40 and 61.50 mV/decade in batch and FIA, respectively), and the response time is very short (amino acids reflect high selectivity of the prepared electrodes. These are used for determination of Ketotifen using potentiometric titration and standard addition methods in pure samples and its pharmaceutical preparations (Zaditen tablets and syrup). The average recovery values are 99.5 and 99.2% with RSD 1.4 and 1.2% for potentiometric titrations and standard addition methods, respectively. The electrode response at different temperatures was also studied.

  10. Determination of nitrofurantoin in pharmaceutical preparations using flow injection-spectrophotometry

    Directory of Open Access Journals (Sweden)

    Hind Hadi

    2017-10-01

    Full Text Available Nitrofurantoin (NIT is used as an antibiotic for the treatment of urinary tract infection. To determine the concentration of NIT in pharmaceutical preparations, two cost-effective extraction-free flow injection (FI spectrophotometric methods (direct and indirect were studied. The direct FI method was based on the reaction of NIT with potassium hydroxide and the formation of a red/orange coloured product with absorbance measured at 471 nm. The indirect method used a reduction reaction of NIT and involved an oxidative coupling step with 3-methyl-2-benzothiazolinone hydrazone hydrochloride (MBTH. The second method resulted in a green coloured product with absorbance measured at 610 nm. Both direct and indirect FI methods were in agreement with Beer’s law over a concentration range of 5–300 µg/mL. In addition, the limit for detection of the reaction product for direct and indirect method was 1.9 and 4.8 µg/mL, respectively. FI spectrophotometric methods used in the present study can be applied for the analysis of NIT in different pharmaceutical dosage forms.

  11. Evaluation of Antibacterial Enrofloxacin in Eggs by Matrix Solid Phase Dispersion-Flow Injection Chemiluminescence

    Directory of Open Access Journals (Sweden)

    Xiaocui Duan

    2014-01-01

    Full Text Available The study based on the chemiluminescence (CL reaction of potassium ferricyanide and luminol in sodium hydroxide medium, enrofloxacin (ENRO could dramatically enhance CL intensities and incorporated with matrix solid-phase dispersion (MSPD technique (Florisil used as dispersant, dichloromethane eluted the target compounds. A simple flow injection chemiluminescence (FL-CL method with MSPD technique for determination of ENRO in eggs was described. Under optimal conditions, the CL intensities were linearly related to ENRO concentration ranging from 4.0×10-8 g.L−1 to 5.0×10-5 g.L−1, with a correlation coefficient of 0.9989 and detection limit of 5.0×10-9 g.L−1. The relative standard deviation was 3.6% at an ENRO concentration of 2.0×10-6 g.L−1. Our testing technique can help ensure food safety, and thus, protect public health.

  12. Multisyringe flow injection analysis of stable and radioactive yttrium in water and biological samples

    Energy Technology Data Exchange (ETDEWEB)

    Fajardo, Y. [Department of Chemistry, University of the Balearic Islands, E-07122 Palma (Spain); Gomez, E. [Department of Chemistry, University of the Balearic Islands, E-07122 Palma (Spain); Garcias, F. [Department of Physics, University of the Balearic Islands, E-07122 Palma (Spain); Cerda, V. [Department of Chemistry, University of the Balearic Islands, E-07122 Palma (Spain); Casas, M. [Department of Physics, University of the Balearic Islands, E-07122 Palma (Spain)]. E-mail: montse.casas@uib.es

    2005-05-10

    A novel multisyringe flow injection (MSFIA) method for the determination of stable and radioactive yttrium by means of a liquid-liquid extraction has been developed. An on-line column containing di-2-ethylhexylphosphoric acid (HDEHP) - a highly selective extractant for the analyte - adsorbed on a C18 support is employed to carry out the isolation from the matrix. Stable and radioactive yttrium concentrations are determined by inductively coupled plasma-atomic emission spectroscopy (ICP-AES) and by a low background proportional counter, respectively. The proposed method shows important advantages because the manual handling of radioactive samples is avoided and throughput is increased. Moreover, as the extractant can be reused, cost per analysis and waste generation are reduced. The lower limit of detection (LLD) of stable yttrium is 10 {mu}g l{sup -1}, whereas for {sup 90}Y is 0.05 Bq. The automated isolation process yields a yttrium recovery close to 100% with a relative standard deviation of 2.3% (n = 10). Our methodology has been successfully applied to different spiked water and biological samples.

  13. Flow-injection chemiluminescence determination of diazepam by oxidation with N-bromosuccinimide.

    Science.gov (United States)

    Han, Suqin; Jia, Shize; Guo, Liang

    2013-01-01

    A rapid and sensitive flow-injection chemiluminescence (FI-CL) method is described for the determination of diazepam based on its reaction with N-bromosuccinimide (NBS) in alkaline medium in the presence of dichlorofluorescein (DCF) as an effective energy-transfer agent. Under optimum conditions, the proposed method allowed the measurement of diazepam over the range of 2.0 × 10(-6) to 2.0 × 10(-4) mol/L with a detection limit of 5.0 × 10(-7) mol/L. The relative standard deviation for 11 parallel measurements of 2.0 × 10(-5) mol/L diazepam was 2.1%. The method was applied satisfactorily for the determination of diazepam in pharmaceutical preparations, and the results agree well with those obtained by spectrophotometry. The use of the proposed system for the determination of diazepam in urine and plasma samples was also tested. The possible mechanism of the chemiluminescence reaction is discussed briefly. Copyright © 2012 John Wiley & Sons, Ltd.

  14. Flow injection analysis as a tool for enhancing oceanographic nutrient measurements--a review.

    Science.gov (United States)

    Worsfold, Paul J; Clough, Robert; Lohan, Maeve C; Monbet, Philippe; Ellis, Peter S; Quétel, Christophe R; Floor, Geerke H; McKelvie, Ian D

    2013-11-25

    Macronutrient elements (C, N and P) and micronutrient elements (Fe, Co, Cu, Zn and Mn) are widely measured in their various physico-chemical forms in open ocean, shelf sea, coastal and estuarine waters. These measurements help to elucidate the biogeochemical cycling of these elements in marine waters and highlight the ecological and socio-economic importance of the oceans. Due to the dynamic nature of marine waters in terms of chemical, biological and physical processes, it is advantageous to make these measurements in situ and in this regard flow injection analysis (FIA) provides a suitable shipboard platform. This review, therefore, discusses the role of FIA in the determination of macro- and micro-nutrient elements, with an emphasis on manifold design and detection strategies for the reliable shipboard determination of specific nutrient species. The application of various FIA manifolds to oceanographic nutrient determinations is discussed, with an emphasis on sensitivity, selectivity, high throughput analysis and suitability for underway analysis and depth profiles. Strategies for enhancing sensitivity and minimizing matrix effects, e.g. refractive index (schlieren) effects and the important role of uncertainty budgets in underpinning method validation and data quality are discussed in some detail. Copyright © 2013 Elsevier B.V. All rights reserved.

  15. Spectrophotometric determination of phosphorus in iron alloys employing a flow injection system

    Directory of Open Access Journals (Sweden)

    Gervasio Ana P. G.

    2001-01-01

    Full Text Available A flow-injection procedure for spectrophotometric determination of phosphorus in electrolytic iron and iron alloys is proposed. The method is based on the ammonium molybdate reaction followed by stannous chloride reduction in acidic medium. In order to circumvent the severe interference caused by the major constituents such as Fe(III and Cr(III, a mini-column packed with AG50W-X8 resin was coupled to the manifold. A sample throughput of 40 determinations per hour, a dynamical range from P 0.25 to 6.00 mg L-1, a reagent consumption of 25 mg ammonium molybdate and 2 mg stannous chloride per determination, and a relative standard deviation < 1% (n = 10 for a typical sample with 2.20 mg L-1 P were achieved. Three different types of samples were used to evaluate system performance. Accuracy was assessed by comparing the results with certified values and no significant difference at 95 % confidence level was observed.

  16. Potentiometric flow injection analysis of mebeverine hydrochloride in serum and urine.

    Science.gov (United States)

    Ibrahim, Hosny; Issa, Yousry M; Abu-Shawish, Hazem M

    2005-01-04

    Four PVC membrane electrodes for the determination of mebeverine hydrochloride (MvCl) were fabricated and fully characterized in terms of composition, life span, usable pH range, working concentration range and temperature. The membranes of these electrodes consist of mebeverinium-silicotungstate (Mv-ST), silicomolybdate (Mv-SM), phosphotungstate (Mv-PT), or phosphomolybdate (Mv-PM) ion-associations dispersed in PVC matrix with dibutyl phthalate plasticizer. The electrodes showed near-Nernstian response over the concentration range of 4.0 x 10(-6) to 1.0 x 10(-2)M MvCl and were applied to the potentiometric determination of mebeverinium ion in pharmaceutical preparations, serum and urine in steady state and flow injection (FI) conditions with average recoveries of 96.4-102 % and relative standard deviations of 0.132-1.86%. The electrodes exhibit good selectivity for MvCl with respect to a large number of inorganic cations, organic cations, sugars and amino acids. The sensitivities of these electrodes are high enough to measure as low as 1.86 microg/ml of MvCl which permit the determination of the Ksp values of the ion-associates used. The proposed potentiometric methods offer the advantages of simplicity, accuracy, automation feasibility and applicability to turbid and colored sample solutions.

  17. The electrochemiluminescence of luminol on titania nanotubes functionalised indium tin oxide glass for flow injection analysis.

    Science.gov (United States)

    Zhao, Qun; Xiao, Changbin; Tu, Yifeng

    2015-10-01

    The titania nanotubes (TiNTs) had been immobilised onto the indium tin oxide (ITO) coated glass to intensify the electrochemiluminescence (ECL) of luminol. The morphology, structure and properties such as specific surface area and transmittance of synthesised TiNTs were characterised. The results indicated that the TiNTs was several hundred nanometres in length with the diameter of 20 nm. In flow injection analysis (FIA) mode, the TiNTs dramatically enhanced the ECL emission of luminol for about 25 multiple, meanwhile decreased the requirement of buffer pH and exciting potential. The ECL emission of luminol on functionalised ITO electrode has sensitive response toward hydrogen peroxide, and extraordinarily responsive toward the antioxidant. Under the optimal conditions, the ECL emission exhibited a linear response within the concentration range from 0.1 mg L(-1) to 30 mg L(-1) and an absolute detection limit of 1.65×10(-10) g of resveratrol. The gross antioxidant activity of blueberry and kiwi were determined with satisfactory recoveries. Copyright © 2015 Elsevier B.V. All rights reserved.

  18. A spectrophotometric flow injection system for streptomycin determination in veterinary samples

    Science.gov (United States)

    Frugeri, Pedro Marcos; Lago, Ayla Campos do; Wisniewski, Célio; Luccas, Pedro Orival

    2014-01-01

    In this work a spectrophotometric flow injection analysis system for streptomycin determination in veterinary samples, is being proposed. The method is based on streptomycin alkaline hydrolysis that forms guanidine, followed by the reaction with Fe(II). The colored product has absorption peak at 520 nm. To evaluate and optimize the system parameters, chemometrics tools, such as factorial design, Pareto chart and Doelhert design, were used. The veterinary samples are diluted in water and introduced in the FIA system, therefore no sample preparation is required. The optimized system presented: linear range of 60 up to 1000 mg L-1, limit of detection of 18 mg L-1 and sampling rate of 36 readings per hour. The precision was checked and the CV for veterinary sample readings were always less than 6.5%. The accuracy was studied by comparison with chromatographic method, thus, five samples of pharmaceutical veterinary were determined by HPLC and by the proposed method, and the results are in agreement (t-test, p = 0.05).

  19. Determination of total phenols in environmental wastewater by flow-injection analysis with a biamperometric detector

    Energy Technology Data Exchange (ETDEWEB)

    Zhao, Chuan; Song, Jun-feng; Zhang, Jun-cai [Institute of Analytical Science, Northwest University, Xi' an 710069 (China)

    2002-10-01

    A flow injection (FI) method with a biamperometric detector, based on the biamperometry for an irreversible redox couple, is described for the determination of phenols in environmental wastewater. The method relies on coupling of the oxidation of phenols at one platinum-wire electrode with the reduction of MnO{sub 4}{sup -} at another platinum wire electrode to enable biamperometric detection with an applied potential difference of 0 V. The linear dynamic range for the dependence of current on phenol concentration was from 1.0 x 10{sup -6} to 1.0 x 10{sup -4} mol L{sup -1}, with a detection limit of 4.0 x 10{sup -7} mol L{sup -1} (signal-to-noise ratio, S/N=3). In comparison with the 4-aminoantipyrine (4-AAP) standard method and the 3-methyl-2-benzothiazoline hydrazone (MBTH) method the proposed method can be used to detect many para-substituted phenols that do not react with 4-AAP and MBTH, and response factors are higher for most of the phenols tested. The method, which is simple, economic, and rapid (180 samples h{sup -1}), has been applied to the analysis of four wastewater samples. The results obtained were compared with those from 4-AAP method. The recoveries obtained by adding phenol standards to samples ranged from 94.3 to 105.2% with a standard deviation of 3.6%. (orig.)

  20. Determination of total phenols in environmental wastewater by flow-injection analysis with a biamperometric detector.

    Science.gov (United States)

    Zhao, Chuan; Song, Jun-Feng; Zhang, Jun-Cai

    2002-10-01

    A flow injection (FI) method with a biamperometric detector, based on the biamperometry for an irreversible redox couple, is described for the determination of phenols in environmental wastewater. The method relies on coupling of the oxidation of phenols at one platinum-wire electrode with the reduction of MnO4- at another platinum wire electrode to enable biamperometric detection with an applied potential difference of 0 V. The linear dynamic range for the dependence of current on phenol concentration was from 1.0 x 10(-6) to 1.0 x 10(-4) mol L(-1), with a detection limit of 4.0 x 10(-7) mol L(-1) (signal-to-noise ratio, S/N=3). In comparison with the 4-aminoantipyrine (4-AAP) standard method and the 3-methyl-2-benzothiazoline hydrazone (MBTH) method the proposed method can be used to detect many para-substituted phenols that do not react with 4-AAP and MBTH, and response factors are higher for most of the phenols tested. The method, which is simple, economic, and rapid (180 samples h(-1)), has been applied to the analysis of four wastewater samples. The results obtained were compared with those from 4-AAP method. The recoveries obtained by adding phenol standards to samples ranged from 94.3 to 105.2% with a standard deviation of 3.6%.

  1. An experimental design approach to the optimisation of a flow injection analysis method for glycine.

    Science.gov (United States)

    Vannecke, C; Baré, S; Bloomfield, M; Massart, D L

    1999-01-01

    A flow injection analysis method for the determination of glycine, based on the reaction with ortho-phtalaldehyde and N-acetylcysteine in a basic buffer, was optimised. In the first step screening of the variables, to select the most important ones, was performed using: (i) a half-fraction factorial design and (ii) a quarter-fraction factorial design, for five factors at two levels. The effects of the factors on the peak height were calculated from both screening designs and compared. For the half-fraction factorial design (resolution IV), the significance of the factor effects on the peak height was checked by: (i) comparing them with a critical effect, calculated from two-factor interactions and based on a t-test, (ii) using a non parametric approach and (iii) drawing a normal probability plot. For the quarter-fraction factorial design (resolution III) the significance of the effects of the factors on the peak height was checked using: (i) a randomization test method, (ii) the non parametric method and (iii) a normal probability plot. In the second step, the factor found to be of importance was optimised using the uniplex method.

  2. Three-dimensional smoothed particle hydrodynamics simulation for injection molding flow of short fiber-reinforced polymer composites

    Science.gov (United States)

    He, Liping; Lu, Gang; Chen, Dachuan; Li, Wenjun; Lu, Chunsheng

    2017-07-01

    This paper investigates the three-dimensional (3D) injection molding flow of short fiber-reinforced polymer composites using a smoothed particle hydrodynamics (SPH) simulation method. The polymer melt was modeled as a power law fluid and the fibers were considered as rigid cylindrical bodies. The filling details and fiber orientation in the injection-molding process were studied. The results indicated that the SPH method could effectively predict the order of filling, fiber accumulation, and heterogeneous distribution of fibers. The SPH simulation also showed that fibers were mainly aligned to the flow direction in the skin layer and inclined to the flow direction in the core layer. Additionally, the fiber-orientation state in the simulation was quantitatively analyzed and found to be consistent with the results calculated by conventional tensor methods.

  3. Investigation of Thrust Augmentation of a 1600-pound Thrust Centrifugal-flow-type Turbojet Engine by Injection of Refrigerants at Compressor Inlets

    Science.gov (United States)

    Jones, William L.; Dowman, Harry W.

    1947-01-01

    Investigations were conducted to determine effectiveness of refrigerants in increasing thrust of turbojet engines. Mixtures of water an alcohol were injected for a range of total flows up to 2.2 lb/sec. Kerosene was injected into inlets covering a range of injected flows up to approximately 30% of normal engine fuel flow. Injection of 2.0 lb/sec of water alone produced an increase in thrust of 35.8% of rate engine conditions and kerosene produced a negligible increase in thrust. Carbon dioxide increased thrust 23.5 percent.

  4. Exploiting zone trapping to avoid liberation of air bubbles in flow-based analytical procedures requiring heating.

    Science.gov (United States)

    Vida, Ana C F; Zagatto, Elias A G

    2014-01-01

    In flow-based analytical procedures requiring heating, liberation of air bubbles is avoided by trapping a sample selected portion into a heated hermetic environment. The flow-through cuvette is maintained into a temperature-controlled aluminium block, thus acting as the trapping element and allowing real-time monitoring. The feasibility of the innovation was demonstrated in the spectrophotometric catalytic determination of vanadium in mineral waters. Air bubbles were not released even for temperatures as high as 95°C. The proposed system handles about 25 samples per hour, requires only 3 mg p-anisidine per determination and yields precise results (r.s.d. = 2.1%), in agreement with ICP-MS. Detection limit was evaluated (3.3 σ criterion) as 0.1 μg L(-1) V.

  5. Urinary bladder blood flow. I. Comparison of clearance of locally injected 99mtechnetium pertechnate and radioactive microsphere technique in dogs

    DEFF Research Database (Denmark)

    Krøyer, Kristian; Bülow, J; Nielsen, S L

    1990-01-01

    The blood flow of the dog urinary bladder measured by radioactive microsphere technique was compared to the clearance of locally injected 99mTechnetium pertechnate (99mTc) in the bladder wall. In semilogarithmic plots the 99mTc washout curves showed a multiexponential course. From the initial...... slopes (median 5.7 min) the bladder blood flow was calculated to be only 30-62% of the results obtained from the radioactive microsphere technique (blood flow in the muscular layer 21.7-44.8 ml/100 g/min). These lower values imply that the rate of removal of the hydrophilic tracer 99mTc at these flow...... blood flow....

  6. Exploiting Maximum Entropy method and ASTER data for assessing debris flow and debris slide susceptibility for the Giampilieri catchment (north-eastern Sicily, Italy).

    KAUST Repository

    Lombardo, Luigi

    2016-07-18

    This study aims at evaluating the performance of the Maximum Entropy method in assessing landslide susceptibility, exploiting topographic and multispectral remote sensing predictors. We selected the catchment of the Giampilieri stream, which is located in the north-eastern sector of Sicily (southern Italy), as test site. On 1/10/2009, a storm rainfall triggered in this area hundreds of debris flow/avalanche phenomena causing extensive economical damage and loss of life. Within this area a presence-only-based statistical method was applied to obtain susceptibility models capable of distinguish future activation sites of debris flow and debris slide, which where the main source failure mechanisms for flow or avalanche type propagation. The set of predictors used in this experiment comprised primary and secondary topographic attributes, derived by processing a high resolution digital elevation model, CORINE land cover data and a set of vegetation and mineral indices obtained by processing multispectral ASTER images. All the selected data sources are dated before the disaster. A spatially random partition technique was adopted for validation, generating fifty replicates for each of the two considered movement typologies in order to assess accuracy, precision and reliability of the models. The debris slide and debris flow susceptibility models produced high performances with the first type being the best fitted. The evaluation of the probability estimates around the mean value for each mapped pixel shows an inverted relation, with the most robust models corresponding to the debris flows. With respect to the role of each predictor within the modelling phase, debris flows appeared to be primarily controlled by topographic attributes whilst the debris slides were better explained by remotely sensed derived indices, particularly by the occurrence of previous wildfires across the slope. The overall excellent performances of the two models suggest promising perspectives for

  7. Effects of Injection Timing on Fluid Flow Characteristics of Partially Premixed Combustion Based on High-Speed Particle Image Velocimetry

    KAUST Repository

    Izadi Najafabadi, Mohammad

    2017-03-28

    Partially Premixed Combustion (PPC) is a promising combustion concept ,based on judicious tuning of the charge stratification, to meet the increasing demands of emission legislation and to improve fuel efficiency. Longer ignition delays of PPC in comparison with conventional diesel combustion provide better fuel/air mixture which decreases soot and NO emissions. Moreover, a proper injection timing and strategy for PPC can improve the combustion stability as a result of a higher level of fuel stratification in comparison with the Homogeneous Charge Compression Ignition (HCCI) concept. Injection timing is the major parameter with which to affect the level of fuel and combustion stratification and to control the combustion phasing and the heat release behavior. The scope of the present study is to investigate the fluid flow characteristics of PPC at different injection timings. To this end, high-speed Particle Image Velocimetry (PIV) is implemented in a light-duty optical engine to measure fluid flow characteristics, including the flow fields, mean velocity and cycle-resolved turbulence, inside the piston bowl as well as the squish region with a temporal resolution of 1 crank angle degree at 800 rpm. Two injectors, having 5 and 7 holes, were compared to see their effects on fluid flow and heat release behavior for different injection timings. Reactive and non-reactive measurements were performed to distinguish injection-driven and combustion-driven turbulence. Formation of vortices and higher turbulence levels enhance the air/fuel interaction, changing the level of fuel stratification and combustion duration. Results demonstrate clearly how turbulence level correlates with heat release behavior, and provide a quantitative dataset for validation of numerical simulations.

  8. Unsteady Stagnation Point Flow and Heat Transfer over a Stretching/Shrinking Sheet with Suction or Injection

    Directory of Open Access Journals (Sweden)

    M. Suali

    2012-01-01

    Full Text Available The unsteady stagnation point flow and heat transfer over a stretching/shrinking sheet with suction/injection is studied. The governing partial differential equations are converted into nonlinear ordinary differential equations using a similarity transformation and solved numerically. Both stretching and shrinking cases are considered. Results for the skin friction coefficient, local Nusselt number, velocity, and temperature profiles are presented for different values of the governing parameters. It is found that the dual solutions exist for the shrinking case, whereas the solution is unique for the stretching case. Numerical results show that the range of dual solutions increases with mass suction and decreases with mass injection.

  9. Determination of acetaldehyde in saliva by gas-diffusion flow injection analysis.

    Science.gov (United States)

    Ramdzan, Adlin N; Mornane, Patrick J; McCullough, Michael J; Mazurek, Waldemar; Kolev, Spas D

    2013-07-05

    The consumption of ethanol is known to increase the likelihood of oral cancer. In addition, there has been a growing concern about possible association between long term use of ethanol-containing mouthwashes and oral cancer. Acetaldehyde, known to be a carcinogen, is the first metabolite of ethanol and it can be produced in the oral cavity after consumption or exposure to ethanol. This paper reports on the development of a gas-diffusion flow injection method for the online determination of salivary acetaldehyde by its colour reaction with 3-methyl-2-benzothiazolinone hydrazone (MBTH) and ferric chloride. Acetaldehyde samples and standards (80 μL) were injected into the donor stream containing NaCl from which acetaldehyde diffused through the hydrophobic Teflon membrane of the gas-diffusion cell into the acceptor stream containing the two reagents mentioned above. The resultant intense green coloured dye was monitored spectrophotometrically at 600 nm. Under the optimum working conditions the method is characterized by a sampling rate of 9h(-1), a linear calibration range of 0.5-15 mg L(-1) (absorbance=5.40×10(-2) [acetaldehyde, mg L(-1)], R(2)=0.998), a relative standard deviation (RSD) of 1.90% (n=10, acetaldehyde concentration of 2.5 mg L(-1)), and a limit of detection (LOD) of 12.3 μg L(-1). The LOD and sampling rate of the proposed method are superior to those of the conventional gas chromatographic (GC) method (LOD=93.0 μg L(-1) and sampling rate=4 h(-1)). The reliability of the proposed method was illustrated by the fact that spiked with acetaldehyde saliva samples yielded excellent recoveries (96.6-101.9%), comparable to those obtained by GC (96.4-102.3%) and there was no statistically significant difference at the 95% confidence level between the two methods when non-spiked saliva samples were analysed. Copyright © 2013 Elsevier B.V. All rights reserved.

  10. A rapid and accurate method for determining protein content in dairy products based on asynchronous-injection alternating merging zone flow-injection spectrophotometry.

    Science.gov (United States)

    Liang, Qin-Qin; Li, Yong-Sheng

    2013-12-01

    An accurate and rapid method and a system to determine protein content using asynchronous-injection alternating merging zone flow-injection spectrophotometry based on reaction between coomassie brilliant blue G250 (CBBG) and protein was established. Main merit of our approach is that it can avoid interferences of other nitric-compounds in samples, such as melamine and urea. Optimized conditions are as follows: Concentrations of CBBG, polyvinyl alcohol (PVA), NaCl and HCl are 150 mg/l, 30 mg/l, 0.1 mol/l and 1.0% (v/v), respectively; volumes of the sample and reagent are 150 μl and 30 μl, respectively; length of a reaction coil is 200 cm; total flow rate is 2.65 ml/min. The linear range of the method is 0.5-15 mg/l (BSA), its detection limit is 0.05 mg/l, relative standard deviation is less than 1.87% (n=11), and analytical speed is 60 samples per hour. Copyright © 2013 Elsevier Ltd. All rights reserved.

  11. Hydrogen injection scheme influence on flow structure in supersonic combustor of constant cross-section

    Science.gov (United States)

    Starov, A. V.; Goldfeld, M. A.

    2017-10-01

    The efficiency of using two variants of hydrogen injection (distributed and non-distributed injection from vertical pylons) is experimentally investigated. The tests are performed in the attached pipeline regime with the Mach number at the model combustor entrance M=2. The combustion chamber has a backward-facing step at the entrance and slotted channels for combustion stabilization. The tested variants of injection differ basically by the shapes of the fuel jets and, correspondingly, by the hydrogen distribution over the combustor. As a result, distributed injection is found to provide faster ignition, upstream displacement of the elevated pressure region, and more intense combustion over the entire combustor volume.

  12. Emerging flow injection mass spectrometry methods for high-throughput quantitative analysis.

    Science.gov (United States)

    Nanita, Sergio C; Kaldon, Laura G

    2016-01-01

    Where does flow injection analysis mass spectrometry (FIA-MS) stand relative to ambient mass spectrometry (MS) and chromatography-MS? Improvements in FIA-MS methods have resulted in fast-expanding uses of this technique. Key advantages of FIA-MS over chromatography-MS are fast analysis (typical run time method simplicity, and FIA-MS offers high-throughput without compromising sensitivity, precision and accuracy as much as ambient MS techniques. Consequently, FIA-MS is increasingly becoming recognized as a suitable technique for applications where quantitative screening of chemicals needs to be performed rapidly and reliably. The FIA-MS methods discussed herein have demonstrated quantitation of diverse analytes, including pharmaceuticals, pesticides, environmental contaminants, and endogenous compounds, at levels ranging from parts-per-billion (ppb) to parts-per-million (ppm) in very complex matrices (such as blood, urine, and a variety of foods of plant and animal origin), allowing successful applications of the technique in clinical diagnostics, metabolomics, environmental sciences, toxicology, and detection of adulterated/counterfeited goods. The recent boom in applications of FIA-MS for high-throughput quantitative analysis has been driven in part by (1) the continuous improvements in sensitivity and selectivity of MS instrumentation, (2) the introduction of novel sample preparation procedures compatible with standalone mass spectrometric analysis such as salting out assisted liquid-liquid extraction (SALLE) with volatile solutes and NH4(+) QuEChERS, and (3) the need to improve efficiency of laboratories to satisfy increasing analytical demand while lowering operational cost. The advantages and drawbacks of quantitative analysis by FIA-MS are discussed in comparison to chromatography-MS and ambient MS (e.g., DESI, LAESI, DART). Generally, FIA-MS sits 'in the middle' between ambient MS and chromatography-MS, offering a balance between analytical capability and

  13. Flow injection analysis biosensor for urea analysis in adulterated milk using enzyme thermistor.

    Science.gov (United States)

    Mishra, Geetesh K; Mishra, Rupesh K; Bhand, Sunil

    2010-12-15

    Urea in adulterated milk is one of the major health concern, it is especially harmful to pregnant women, children, and the sick. A sophisticated and reliable detection system is needed to replace current diagnostic tools for the urea in the milk. In this work, we report a flow injection analysis-enzyme thermistor (FIA-ET) bio-sensing system for monitoring of urea in adulterated milk. This biosensor was made of the covalently immobilized enzyme urease (Jack bean) on controlled pore glass (CPG) and packed into a column inside thermistor, which selectively hydrolysed the urea present in the sample. The specific heat registered from the hydrolysis of urea was found proportional to the concentration of urea present in the milk sample. The biosensor showed a linear range 1-200 mM, with % R.S.D. 0.96 for urea in 100 mM phosphate buffer, pH 7.2. Good recoveries were obtained (97.56-108.7%) for urea up to 200 mM in the spiked milk samples with % R.S.D. 0.95. In the adulterated milk, a simple filtration strategy and matrix matching technique was used to analyse urea. The response time of the sensor was evaluated for urea, which was 2 min, and it gives satisfactory output. A good comparison was observed between the urea concentrations measured through FIA-ET and the colorimetric method. These results indicate that utilizing this system could be very effective to detect low and high level of urea in adulterated milk. The immobilized urease column exhibited a good operational stability up to 180 days when used continuously at room temperature. Copyright © 2010 Elsevier B.V. All rights reserved.

  14. Flow-injection spectrophotometric determination of cyanate in bioremediation processes by use of immobilised inducible cyanase

    Energy Technology Data Exchange (ETDEWEB)

    Luque-Almagro, V.M. [Department of Biochemistry and Molecular Biology, Edifice Severo Ochoa, Campus of Rabanales, University of Cordoba, 14071, Cordoba (Spain); Blasco, R. [Department of Biochemistry, Molecular Biology and Genetics, Veterinary School, University of Extremadura, 10071, Caceres (Spain); Fernandez-Romero, J.M.; Castro, M.D. Luque de [Department of Analytical Chemistry, Annex Edifice Marie Curie, Campus of Rabanales, University of Cordoba, 14071, Cordoba (Spain)

    2003-11-01

    A new flow injection (FI) method for photometric monitoring of cyanate in bioremediation processes using immobilised native cyanase is described. The method is based on the catalytic reaction between cyanate and bicarbonate to produce ammonia and carbon dioxide in the presence of an inducible native cyanase, immobilised in a reactor packed with glass beads. Two degrees of purification of the biocatalyst were used - heated cell-free extract and purified extract of cyanase from Pseudomonas pseudoalcaligenes CECT 5344. The ammonia produced by the enzymatic reaction is finally monitored photometrically at 700 nm using a modification of the conventional Berthelot method. The method furnishes different calibration curves depending on the degree of purification of the cyanase, with linear ranges between 1.23 and 616.50 {mu}mol L{sup -1} (r{sup 2}=0.9979, n=7) and between 1.07 and 308.25 {mu}mol L{sup -1} (r{sup 2}= 0.9992, n=7) for the heated cell-free extract and the purified cyanase extract, respectively. No statistically significant differences between the samples were found in the precision study evaluated at two cyanate concentration levels using one-way analysis of variance. A sampling frequency of 15 h{sup -1} was achieved. The method was used to monitor cyanate consumption in a cyanate bioremediation tank inoculated with Pseudomonas pseudoalcaligenes CECT 5344 strain. The correlation between cyanate degradation and ammonia production was tested using a conventional method. Finally, the method was applied to different samples collected from the bioremediation tank using the standard addition method; recoveries between 85.9 and 97.4% were obtained. (orig.)

  15. Flow-injection spectrophotometric determination of cyanate in bioremediation processes by use of immobilised inducible cyanase.

    Science.gov (United States)

    Luque-Almagro, V M; Blasco, R; Fernández-Romero, J M; de Castro, M D Luque

    2003-11-01

    A new flow injection (FI) method for photometric monitoring of cyanate in bioremediation processes using immobilised native cyanase is described. The method is based on the catalytic reaction between cyanate and bicarbonate to produce ammonia and carbon dioxide in the presence of an inducible native cyanase, immobilised in a reactor packed with glass beads. Two degrees of purification of the biocatalyst were used-heated cell-free extract and purified extract of cyanase from Pseudomonas pseudoalcaligenes CECT 5344. The ammonia produced by the enzymatic reaction is finally monitored photometrically at 700 nm using a modification of the conventional Berthelot method. The method furnishes different calibration curves depending on the degree of purification of the cyanase, with linear ranges between 1.23 and 616.50 micromol L(-1) ( r(2)=0.9979, n=7) and between 1.07 and 308.25 micro mol L(-1) ( r(2)= 0.9992, n=7) for the heated cell-free extract and the purified cyanase extract, respectively. No statistically significant differences between the samples were found in the precision study evaluated at two cyanate concentration levels using one-way analysis of variance. A sampling frequency of 15 h(-1) was achieved. The method was used to monitor cyanate consumption in a cyanate bioremediation tank inoculated with Pseudomonas pseudoalcaligenes CECT 5344 strain. The correlation between cyanate degradation and ammonia production was tested using a conventional method. Finally, the method was applied to different samples collected from the bioremediation tank using the standard addition method; recoveries between 85.9 and 97.4% were obtained.

  16. Use of flow injection mass spectrometric fingerprinting and chemometrics for differentiation of three black cohosh species

    Science.gov (United States)

    Huang, Huilian; Sun, Jianghao; McCoy, Joe-Ann; Zhong, Haiyan; Fletcher, Edward J.; Harnly, James; Chen, Pei

    2015-03-01

    Flow injection mass spectrometry (FIMS) was used to provide chemical fingerprints of black cohosh (Actaea racemosa L.) in a manner of minutes by omitting the separation step. This method has proven to be a powerful tool for botanical authentication and in this study it was used to distinguish between three Actaea species prior to a more detailed chemical analysis using ultra high-performance liquid chromatography high-resolution mass spectrometry (UHPLC-HRMS). Black cohosh has become increasingly popular as a dietary supplement in the United States for the treatment of symptoms related to menopause. However, it has been known to be adulterated with the Asian Actaea dahurica (Turcz. ex Fisch. & C.A.Mey.) Franch. species (syn. Cimicifuga dahurica (Turcz.) Maxim). Existing methods for identification of black cohosh and differentiation of Actaea species are usually lengthy, laborious, and lack robustness, often based on the comparison of a few pre-selected components. Chemical fingerprints were obtained for 77 black cohosh samples and their related species using FIMS in the negative ion mode. The analysis time for each sample was less than 2 min. All data were processed using principal component analysis (PCA). FIMS fingerprints could readily differentiate all three species. Representative samples from each of the three species were further examined using UHPLC-MS to provide detailed profiles of the chemical differences between the three species and were compared to the PCA loadings. This study demonstrates a simple, fast, and easy analytical method that can be used to differentiate A. racemosa, Actaea podocarpa, and A. dahurica.

  17. Flow injection chemiluminescence determination of loxoprofen and naproxen with the acidic permanganate-sulfite system

    Directory of Open Access Journals (Sweden)

    Li-Juan Wang

    2011-02-01

    Full Text Available A novel flow injection chemiluminescence (CL method for the determination of loxoprofen and naproxen was proposed based on the CL system of KMnO4, and Na2SO3 in acid media. The CL intensity of KMnO4-Na2SO3 was greatly enhaneed in the presence of loxoprofen and naproxen. The mechanism of the CL reaction was studied by the kinetic proecss and UV-vis absorption and the conditions were optimized. Under optimized conditions, the CL intensity was linear with loxoprofen and naproxen concentration in the range of 7.0 × 10−8 – 1.0 × 10−5 g/mL and 2.0 × 10−7 – 4.0 × 10−6 g/mL with the detection limit of 2.0 × 10−8 g/mL and 3.0 × 10−8 g/mL (S/N = 3, respectively. Thc relative standard deviations were 2.39% and 1.37% for 5.0 × 10−7 g/mL naproxen and 5.0 × 10−7 g/mL loxoprofen (n = 10, respectively. The proposed method was satisfactorily applied to thc determination of loxoprofen and naproxen in pharmaceutical preparations. Keywords: chemiluminescence, KMnO4, loxoprofen, naproxen

  18. Study of the influence of gas flow on PECVD diamond growth: influence of the separate injection of gases

    Science.gov (United States)

    Mesbahi, A.; Silva, F.

    2017-11-01

    This study is a follow-up to previously published modeling work examining a bell jar microwave plasma CVD reactor operating at high pressure (Mesbahi et al 2013 J. Phys. D: Appl. Phys. 46 385502). In this paper, we present the influence of gas injection mode on flow structure, on the production and coupled transport of diamond growth key species, and on the resulting diamond growth. Several gas injection configurations have been tested and experimental results in terms of growth rate and thickness uniformity will be compared with numerical simulations. In this study, we found that direct injection of methane closer to the discharge allowed one to significantly increase the diamond growth rate. These results will be discussed using a non-dimensional analysis of the transport phenomena (mass, energy and momentum by convection and diffusion) and production of the CH3 radical in the reactor.

  19. Suction/Injection Effects on the Swirling Flow of a Reiner-Rivlin Fluid near a Rough Surface

    Directory of Open Access Journals (Sweden)

    Bikash Sahoo

    2015-01-01

    Full Text Available The similarity equations for the Bödewadt flow of a non-Newtonian Reiner-Rivlin fluid, subject to uniform suction/injection, are solved numerically. The conventional no-slip boundary conditions are replaced by corresponding partial slip boundary conditions, owing to the roughness of the infinite stationary disk. The combined effects of surface slip (λ, suction/injection velocity (W, and cross-viscous parameter (L on the momentum boundary layer are studied in detail. It is interesting to find that suction dominates the oscillations in the velocity profiles and decreases the boundary layer thickness significantly. On the other hand, injection has opposite effects on the velocity profiles and the boundary layer thickness.

  20. Automated determination of uranium(VI) at ultra trace levels exploiting flow techniques and spectrophotometric detection using a liquid waveguide capillary cell

    Energy Technology Data Exchange (ETDEWEB)

    Avivar, Jessica; Ferrer, Laura; Cerda, Victor [University of the Balearic Islands, Chemistry Department, Palma (Spain); Casas, Montserrat [University of the Balearic Islands Cra, Physics Department and IFISC-CSIC, Palma (Spain)

    2010-05-15

    Rapid and fully automated multisyringe flow-injection analysis (MSFIA) with a multi-pumping flow system (MPFS) coupled to a long path-length liquid waveguide capillary cell (LWCC) is proposed for the determination of uranium(VI) at ultra trace levels. On-line separation and pre-concentration of uranium is carried out by means of a TRU resin. After elution, uranium(VI) is spectrophotometrically detected after reaction with arsenazo-III. Combination of the MSFIA and MPFS techniques with the TRU-resin enables the analysis to be performed in a short time, using large sample volumes and achieving high selectivity and sensitivity levels. A detection limit of 12.6 ng L{sup -1} (ppt) is reached for a 100-mL sample volume. The versatility of the proposed method also enables pre-concentration of variable sample volumes, enabling application of the analysis to a wide concentration range. Reproducibility of better than 5% and a resin durability of 40 injections should be emphasized. The developed method was successfully applied to different types of environmental sample matrices with recoveries between 95 and 108%. (orig.)

  1. Short-term effects of intravitreal triamcinolone acetonide injection on ocular blood flow evaluated with color Doppler ultrasonography

    Directory of Open Access Journals (Sweden)

    Mustafa Alpaslan Anayol

    2014-10-01

    Full Text Available AIM:To evaluate the changes in ocular blood flow with color Doppler ultrasonography (CDU after intravitreal triamcinolone acetonide (IVTA injection.METHODS: A total of 46 patients who underwent IVTA (4 mg/0.1 mL injection for diabetic macular edema (DME (n=22, central retinal vein occlusion (CRVO (n=12 and choroidal neovascular membrane (CNVM (n=12 were included in the study. Peak systolic velocity (PSV, end diastolic velocity (EDV and resistivity index (RI were measured from the ophthalmic artery (OA, the central retinal artery (CRA and the posterior ciliary artery (PCA of each patient with CDU before, at the end of the first week and at the end of the first month following IVTA injection.RESULTS:In the DME group, PSV of OA at the first of the first month (mean±SD (37.48±10.87 cm/s increased compared to pre-injection value (31.39±10.84 cm/s (P=0.048. There was a statistically significant decrease (P=0.049 in PSV of CRA at the end of the first month (7.97±2.67 cm/s compared to the pre-injection (9.47±3.37 cm/s. There was not any statistically significant difference on the other parameters in the DME group. Also, there was not any statistically significant difference on the ocular blood flow values in the CRVO and CNVM groups.CONCLUSION: We observed that 4 mg/0.1 mL IVTA increased PSV of OA and decreased PSV of CRA in DME patients and did not have any effect on ocular blood flow values of CRVO and CNVM patients.

  2. Quantitative investigation of compressible mixing: Staged transverse injection into Mach 2 flow

    Science.gov (United States)

    Hollo, Steven D.; Mcdaniel, James C.; Hartfield, Roy J., Jr.

    1994-01-01

    Planar measurements of the injectant mole fraction distribution and the velocity field within a supersonic mixing flowfield have been made using laser-induced iodine fluorescence. The flowfield investigated in this work is staged transverse injection of air into a Mach 2 freestream. A complete three-dimensional survey of the injectant mole fraction distribution has been generated, and a single planar velocity measurement has been completed. The measurements reveal the dramatic effect of streamwise vortices on the mixing in the near field of the injectors, as well as the rapid mixing generated by staging two fuel injectors. Analysis of the downstream decay of the maximum injectant mole fraction in this and other supersonic mixing flowfields indicates that the relative rate of injectant mixing well downstream of the injectors is independent of injection geometry, freestream Mach number, and injectant molecular weight. Mixing within this region of the flowfield is dominated by small-scale turbulence within the injectant plume. The transition of the dominant mixing mechanism, from vortex-driven mixing in the near field to small-scale turbulent mixing in the far field, was found to occur in the region about 10 diameters downstream of the injectors.

  3. Geological Factors Affecting Flow Spatial Continuity in Water Injection of Units Operating in the LGITJ–0102 Ore Body

    Directory of Open Access Journals (Sweden)

    Ilver M. Soto-Loaiza

    2016-05-01

    Full Text Available The objective of the investigation was to identify the geological factors affecting the spatial continuity of the flow during the process of flank water injection in the units operating in the Lower Lagunilla Hydrocarbon Ore Body. This included the evaluation of the recovery factor, the petro-physic properties such as porosity, permeability, water saturation and rock type and quality in each flow unit. it was observed that the rock type of the geologic structure in the ore body is variable. The lowest values for the petro-physic properties were found in the southern area while a high variability of these parameters was observed in the northern and central areas. It was concluded that the northern area has a great potential for the development of new injection projects for petroleum recovery.

  4. Chemiluminescence determination of ferulic acid by flow-injection analysis using cerium(IV) sensitized by rhodamine 6G.

    Science.gov (United States)

    Wang, Ju Peng; Li, Nian Bing; Luo, Hong Qun

    2008-11-01

    A simple, sensitive and rapid flow-injection chemiluminescence method has been developed for the determination of ferulic acid based on the chemiluminescence reaction of ferulic acid with rhodamine 6G and ceric sulfate in sulphuric acid medium. Strong chemiluminescence signal was observed when ferulic acid was injected into the acidic ceric sulfate solution in a flow-cell. The present method allowed the determination of ferulic acid in the concentration range of 8.0 x 10(-6) to 1.0 x 10(-4) mol l(-1) and the detection limit for ferulic acid was 8.7 x 10(-9) mol l(-1). The relative standard deviation was 2.4% for 10 replicate analyses of 1.0 x 10(-5) mol l(-1) ferulic acid. The proposed method was applied to the determination of ferulic acid in Taita Beauty Essence samples with satisfactory results.

  5. Determination of inorganic arsenic and its organic metabolites in urine by flow-injection hydride generation atomic absorption spectrometry.

    Science.gov (United States)

    Hanna, C P; Tyson, J F; McIntosh, S

    1993-08-01

    A method has been developed for the determination of inorganic arsenic [As(III) and As(V)] and its organic metabolites (monomethylarsenic and dimethylarsenic) in urine by flow-injection hydride generation atomic absorption spectrometry. The nontoxic seafood-derived arsenobetaine and arsenocholine species were first separated by a solid-phase extraction procedure. The remaining sample was digested with a mixture of nitric and sulfuric acids and potassium dichromate, followed by attack with hydrogen peroxide. The resulting As(V) was reduced to As(III) with potassium iodide in hydrochloric acid before injection into the flow-injection manifold. The percentage analytical recoveries (mean +/- 95% confidence interval) of various arsenic species added to a urine specimen at 250 micrograms/L were 108 +/- 2, 112 +/- 11, 104 +/- 7, and 95 +/- 5 for As(III), As(V), monomethylarsenic, and dimethylarsenic, respectively. For the determination of arsenic in Standard Reference Material 2670 (toxic metals in human urine), results agreed with the certified value (480 +/- 100 micrograms/L). Analyses of samples for the Centre de Toxicologie du Quebec, containing seafood-derived species, demonstrated the viability of the separation procedure. Detection limits were between 0.1 and 0.2 microgram/L in the solution injected into the manifold, and precision at 10 micrograms/L was between 2% and 3% (CV). These preliminary results show that the method might be applicable to determinations of arsenic in a range of clinical urine specimens.

  6. Study of process parameters effect on the filling phase of micro injection moulding using weld lines as flow markers

    DEFF Research Database (Denmark)

    Tosello, Guido; Gava, Alberto; Hansen, Hans Nørgaard

    2010-01-01

    , the relationships between the filling pattern and the different process parameter settings have to be established. In this paper, a novel approach based on the use of weld lines as flow markers to trace the development of the flow front during the filling is proposed. The effects on the filling stage of process...... parameters such as temperature of the melt, temperature of the mould, injection speed and packing pressure have been investigated. An optical coordinate measuring machine has been employed for the investigation. The micro-cavity, which presents micro-features ranging from 600 μm down to 150 μm, has been...

  7. Cavitating flow control through continuous tangential mass injection on a 2D hydrofoil at a small attack angle

    Directory of Open Access Journals (Sweden)

    Timoshevskiy Mikhail V.

    2016-01-01

    Full Text Available We studied cavitating flow over the suction side of a symmetric 2D foil – a scaled-down model of high-pressure hydroturbine guide vanes (GV – in different cavitation regimes at the attack angle of 3°. High-speed imaging was used to analyze spatial patterns and time dynamics of the gas-vapour cavities. A hydroacoustic pressure transducer was employed to register time-spectra of pressure fluctuations nearby the hydrofoil. A PIV technique was applied to measure the velocity fields and its fluctuations. The active flow control was implemented by means of a continuous liquid supply with different flow rates through a slot channel located in the GV surface. It was found that the active mass injection does not influence the primary flow upstream of the slot channel position. For the cavitation-free and cavitation inception cases, the injection was shown to make the turbulent wake past the GV section more intense. However, at the developed cavitation regimes the active flow management made it possible to reduce substantially the amplitude or even totally suppress the periodic cavity length oscillations and pressure pulsations associated with them.

  8. Spectrophotometric flow-injection determination of sulphite in white wines involving gas diffusion through a concentric tubular membrane

    OpenAIRE

    Melo Denise; Zagatto Elias A. G.; Mattos Ivanildo L.; Maniasso Nelson

    2003-01-01

    A flow-injection system is proposed for the spectrophotometric determination of sulphite in white wines. The method involves analyte conversion to SO2, gas diffusion through a Teflon® semi-permeable membrane, collection into an alkaline stream (pH 8), reaction with Malachite green (MG) and monitoring at 620 nm. With a concentric tubular membrane, the system design was simplified. Influence of reagent concentrations, pH of donor and acceptor streams, temperature, timing, surfactant addition an...

  9. A simple flow-injection method for the determination of blood glucose using a Technicon immobilized enzyme coil

    OpenAIRE

    Gizurarson, Sveinbjörn

    1989-01-01

    The applicability of a single-channel flow-injection system with immobilized enzyme coil (Technicon) and UV detection to the determination of glucose is described. The method was used for a pure glucose solution and for serum. The detection limit was 0.10 mM, the rate of determination was 20-40 per hour and the precision was satisfactory. The system is very simple and practical when many analysis are to be determined periodically.

  10. Continuous-flow ultrasound assisted oxidative desulfurization (UAOD) process: An efficient diesel treatment by injection of the aqueous phase.

    Science.gov (United States)

    Rahimi, Masoud; Shahhosseini, Shahrokh; Movahedirad, Salman

    2017-11-01

    A new continuous-flow ultrasound assisted oxidative desulfurization (UAOD) process was developed in order to decrease energy and aqueous phase consumption. In this process the aqueous phase is injected below the horn tip leading to enhanced mixing of the phases. Diesel fuel as the oil phase with sulfur content of 1550ppmw and an appropriate mixture of hydrogen peroxide and formic acid as the aqueous phase were used. At the first step, the optimized condition for the sulfur removal has been obtained in the batch mode operation. Hence, the effect of more important oxidation parameters; oxidant-to-sulfur molar ratio, acid-to-sulfur molar ratio and sonication time were investigated. Then the optimized conditions were obtained using Response Surface Methodology (RSM) technique. Afterwards, some experiments corresponding to the best batch condition and also with objective of minimizing the residence time and aqueous phase to fuel volume ratio have been conducted in a newly designed double-compartment reactor with injection of the aqueous phase to evaluate the process in a continuous flow operation. In addition, the effect of nozzle diameter has been examined. Significant improvement on the sulfur removal was observed specially in lower sonication time in the case of dispersion method in comparison with the conventional contact between two phases. Ultimately, the flow pattern induced by ultrasonic device, and also injection of the aqueous phase were analyzed quantitatively and qualitatively by capturing the sequential images. Copyright © 2017 Elsevier B.V. All rights reserved.

  11. Flow injection analysis with on-line nylon powder extraction for room-temperature phosphorescence determination of thiabendazole.

    Science.gov (United States)

    Piccirilli, G N; Escandar, G M

    2009-07-30

    A fast and very selective flow-through phosphorescence optosensor was designed and characterized for the determination of the fungicide thiabendazole in water samples. For the first time, thiabendazole was determined using a flow-through optosensor based on the phosphorescence signals obtained when it is retained in a solid support. While thiabendazole does not phosphoresce in packing materials commonly used to fill the flow-cell, significant emission signals are observed when it is retained on nylon powder in the presence of iodide and sulfite. The experimental set-up was based on a flow-injection manifold coupled to an on-line phosphorescence detector containing nylon powder packed in a conventional flow-cell. Potassium iodide and sodium sulfite were added to sample aliquots to improve the thiabendazole phosphorescence and injected in the flow manifold using water as carrier. After the phosphorescence emission was registered, the analyte was eluted from the packed nylon with a 65% (v/v) methanol-water mixture. Optimal instrumentation, experimental and flow conditions were evaluated. Using a sample volume of 2000 microL, the analytical signal showed a very good linearity in the range 12.9-110 ng mL(-1), with a detection limit of 4.5 ng mL(-1), and a sample throughput of about 14 samples per hour. The effects of the presence of concomitant species in the thiabendazole phosphorescence signal were studied, and a comparison with the fluorescence nylon-powder optosensor was carried out and discussed. Finally, the applicability of the proposed optosensor was tested in water samples, and satisfactory recoveries ranging between 97% and 105% were obtained.

  12. Seasonal Variability in Regional Ice Flow Due to Meltwater Injection Into the Shear Margins of Jakobshavn Isbræ

    Science.gov (United States)

    Cavanagh, J. P.; Lampkin, D. J.; Moon, T.

    2017-12-01

    The impact of meltwater injection into the shear margins of Jakobshavn Isbræ via drainage from water-filled crevasses on ice flow is examined. We use Landsat-8 Operational Land Imager panchromatic, high-resolution imagery to monitor the spatiotemporal variability of seven water-filled crevasse ponds during the summers of 2013 to 2015. The timing of drainage from water-filled crevasses coincides with an increase of 2 to 20% in measured ice velocity beyond Jakobshavn Isbræ shear margins, which we define as extramarginal ice velocity. Some water-filled crevasse groups demonstrate multiple drainage events within a single melt season. Numerical simulations show that hydrologic shear weakening due to water-filled crevasse drainage can accelerate extramarginal flow by as much as 35% within 10 km of the margins and enhance mass flux through the shear margins by 12%. This work demonstrates a novel mechanism through which surface melt can influence regional ice flow.

  13. An automatic, vigorous-injection assisted dispersive liquid-liquid microextraction technique for stopped-flow spectrophotometric detection of boron.

    Science.gov (United States)

    Alexovič, Michal; Wieczorek, Marcin; Kozak, Joanna; Kościelniak, Paweł; Balogh, Ioseph S; Andruch, Vasil

    2015-02-01

    A novel automatic vigorous-injection assisted dispersive liquid-liquid microextraction procedure based on the use of a modified single-valve sequential injection manifold (SV-SIA) was developed and applied for determination of boron in water samples. The major novelties in the procedure are the achieving of efficient dispersive liquid-liquid microextraction by means of single vigorous-injection (250 µL, 900 µL s(-1)) of the extraction solvent (n-amylacetate) into aqueous phase resulting in the effective dispersive mixing without using dispersive solvent and after self-separation of the phases, as well as forwarding of the extraction phase directly to a Z-flow cell (10 mm) without the use of a holding coil for stopped-flow spectrophotometric detection. The calibration working range was linear up to 2.43 mg L(-1) of boron at 426nm wavelength. The limit of detection, calculated as 3s of a blank test (n=10), was found to be 0.003 mg L(-1), and the relative standard deviation, measured as ten replicable concentrations at 0.41 mg L(-1) of boron was determined to be 5.6%. The validation of the method was tested using certified reference material. Copyright © 2014 Elsevier B.V. All rights reserved.

  14. Subcutaneous Injections

    DEFF Research Database (Denmark)

    Thomsen, Maria

    This thesis is about visualization and characterization of the tissue-device interaction during subcutaneous injection. The tissue pressure build-up during subcutaneous injections was measured in humans. The insulin pen FlexTouchr (Novo Nordisk A/S) was used for the measurements and the pressure...... build-up was evaluated indirectly from the changes in the flow rate between subcutaneous injections and air injections. This method enabled the tissue counter pressure to be evaluated without a formal clinical study approval. The measurements were coupled to a model for the pressure evolution...... in subcutaneous tissue, based on mass conservation and flow in a porous medium. From the measurements the flow permeability and bulk modulus of the tissue were determined. In the adipose tissue the drug forms a bolus from where it is absorbed by the blood capillaries. The spatial distribution of the injected...

  15. Discharge flow of granular media from silos with a lateral orifice and injection of air

    Directory of Open Access Journals (Sweden)

    Aussillous Pascale

    2017-01-01

    Full Text Available Few studies concern the prediction of the mass flow rate of a granular media discharged from a silo with a lateral orifice. However, this situation can have pratical interest considering a tank of granular material with a leak on its side. We studied experimentally the discharge of a vertical silo filled by spherical glass beads. We consider rectangular silos with a rectangular orifice. The impact of size, aspect ratio and position of the orifice and the effect of an additional air flow were studied. The measured parameters are the mass flow rate and the pressure along the silo, whereas the controlled parameters are the size of particles, and the flow rate of air. We identified two regimes of discharge according to the aspect ratio (of width to height of the rectangular orifice. Increasing the air flow rate induces an increase of the granular media flow rate. Using a simple physical model to describe the grains and gas flow, we put in evidence the role played by the air pressure gradient at the outlet. Then we compared the experimental results with continuum Navier-Stokes simulations with the granular μ(I-rheology. We showed that the continuum μ(I-rheology describes well our discharge flow of granular media from silos, taking into account the effect of the position of the orifice as well as the coupling with the gas flow.

  16. Potentiometric flow injection sensing system for determination of heparin based on current-controlled release of protamine.

    Science.gov (United States)

    Lei, Jiahong; Ding, Jiawang; Chen, Yan; Qin, Wei

    2015-02-09

    A flow injection system incorporated with a polycation-sensitive polymeric membrane electrode in the flow cell is proposed for potentiometric determination of heparin. An external current in nano-ampere scale is continuously applied across the polymeric membrane for controlled release of protamine from the inner filling solution to the sample solution, which makes the electrode membrane regenerate quickly after each measurement. The protamine released at membrane-sample interface is consumed by heparin injected into the flow cell via their strong electrostatic interaction, thus decreasing the measured potential, by which heparin can be detected. Under optimized conditions, a linear relationship between the potential peak height and the concentration of heparin in the sample solution can be obtained in the range of 0.1-2.0 U mL(-1), and the detection limit is 0.06 U mL(-1). The proposed potentiometric sensing system has been successfully applied to the determination of heparin in undiluted sheep whole blood. Copyright © 2014 Elsevier B.V. All rights reserved.

  17. Chemically prepared silver electrode for determination of N-acetyl-L-cysteine by flow-injection potentiometry.

    Science.gov (United States)

    Kolar, M; Dobcnik, D

    2003-01-01

    This paper describes the use of the silver electrode by means of chemical pretreatment of the electrode surface with mercuric(II) chloride solution and potassium iodide solution in flow injection analysis (FIA). The electrode is used as a potentiometric sensor for the indirect determination of NAC in a carrier stream containing iodine. A one-channel flow system that consists of a peristaltic pump, injection valve, a silver wire electrode and a saturated calomel reference electrode (SCE) was used. Some typical FIA parameters such as flow rate, tube length and composition of the carrier stream were varied. The electrode is further characterised by a constant linear response within the concentration range for NAC between 4.0 x 10(-6) and 1.0 x 10(-3) M at the slope of 60.6 +/- 1.0 mV/p(NAC). Some pharmaceutical products containing NAC were also tested. These results can be compared to the results obtained by the direct potentiometric titrations with silver nitrate and are also in good agreement with values declared by pharmaceutical manufacturers.

  18. Performance comparison of supersonic ejectors with different motive gas injection schemes applicable for flowing medium gas laser

    Science.gov (United States)

    Singhal, G.; Subbarao, P. M. V.; Mainuddin; Tyagi, R. K.; Dawar, A. L.

    2017-05-01

    A class of flowing medium gas lasers with low generator pressures employ supersonic flows with low cavity pressure and are primarily categorized as high throughput systems capable of being scaled up to MW class. These include; Chemical Oxygen Iodine Laser (COIL) and Hydrogen (Deuterium) Fluoride (HF/DF). The practicability of such laser systems for various applications is enhanced by exhausting the effluents directly to ambient atmosphere. Consequently, ejector based pressure recovery forms a potent configuration for open cycle operation. Conventionally these gas laser systems require at least two ejector stages with low pressure stage being more critical, since it directly entrains the laser media, and the ensuing perturbation of cavity flow, if any, may affect laser operation. Hence, the choice of plausible motive gas injection schemes viz., peripheral or central is a fluid dynamic issue of interest, and a parametric experimental performance comparison would be beneficial. Thus, the focus is to experimentally characterize the effect of variation in motive gas supply pressure, entrainment ratio, back pressure conditions, nozzle injection position operated together with a COIL device and discern the reasons for the behavior.

  19. Effect of viscous dissipation and suction/injection on MHD nanofluid flow over a wedge with porous medium and slip

    Directory of Open Access Journals (Sweden)

    Alok Kumar Pandey

    2016-12-01

    Full Text Available The purpose of present study is to identify the effects of viscous dissipation and suction/injection on MHD flow of a nanofluid past a wedge with convective surface in the appearance of slip flow and porous medium. The basic non-linear PDEs of flow and energy are altered into a set of non-linear ODEs using auxiliary similarity transformations. The system of equations together with coupled boundary conditions have been solved numerically by applying Runge-Kutta-Fehlberg procedure via shooting scheme. The influence of relevant parameters on non-dimensional velocity and temperature profiles are depicted graphically and investigated in detail. The results elucidate that as enhance in the Eckert number, the skin friction coefficient increases, while heat transfer rate decreases. The outcomes also specify that thermal boundary layer thickness declines with an increase in suction parameter. Moreover, it is accelerated with augment in injection parameter. The results are analogized with the study published earlier and it creates a fine concord.

  20. Exploiting pi-acceptors for the determination of thyroid hormones (T3 and T4) using a single interface flow system.

    Science.gov (United States)

    Silvestre, Cristina I C; Santos, João L M; Lima, José L F C; Zagatto, Elias A G

    2009-09-15

    A fully automated methodology was developed for the determination of the thyroid hormones levothyroxine (T4) and liothyronine (T3). The proposed method exploits the formation of highly coloured charge-transfer (CT) complexes between these compounds, acting as electron donors, and pi-acceptors such as chloranilic acid (CLA) and 2,3-dichloro-5,6-dicyano-p-benzoquinone (DDQ). For automation of the analytical procedure a simple, fast and versatile single interface flow system (SIFA) was implemented guaranteeing a simplified performance optimisation, low maintenance and a cost-effective operation. Moreover, the single reaction interface assured a convenient and straightforward approach for implementing Job's method of continuous variations used to establish the stoichiometry of the formed CT complexes. Linear calibration plots for levothyroxine and liothyronine concentrations ranging from 5.0 x 10(-5) to 2.5 x 10(-4) mol L(-1) and 1.0 x 10(-5) to 1.0 x 10(-4)mol L(-1), respectively, were obtained, with good precision (R.S.D. <4.6% and <3.9%) and with a determination frequency of 26 h(-1) for both drugs. The results obtained for pharmaceutical formulations were statistically comparable to the declared hormone amount with relative deviations lower than 2.1%. The accuracy was confirmed by carrying out recovery studies, which furnished recovery values ranging from 96.3% to 103.7% for levothyroxine and 100.1% for liothyronine.

  1. Reagent-free determination of amikacin content in amikacin sulfate injections by FTIR derivative spectroscopy in a continuous flow system

    Directory of Open Access Journals (Sweden)

    José F. Ovalles

    2014-04-01

    Full Text Available The quantitative estimation of amikacin (AMK in AMK sulfate injection samples is reported using FTIR-derivative spectrometric method in a continuous flow system. Fourier transform of mid-IR spectra were recorded without any sample pretreatment. A good linear calibration (r>0.999, %RSD<2.0 in the range of 7.7–77.0 mg/mL was found. The results showed a good correlation with the manufacturer's and overall they all fell within acceptable limits of most pharmacopoeial monographs on AMK sulfate.

  2. A flow-injection mass spectrometry fingerprinting method for authentication and quality assessment of Scutellaria lateriflora-based dietary supplements.

    Science.gov (United States)

    Sun, Jianghao; Chen, Pei

    2011-09-01

    Scutellaria lateriflora, commonly known as skullcap, is used as an ingredient in numerous herbal products. However, it has been occasionally adulterated/contaminated with Teucrium canadense and/or Teucrium chamaedrys, commonly known as germander, due to the morphological similarities between the two genera. The latter contains hepatotoxic diterpenes. Despite the potential hepatotoxicity introduced by germander contamination, analytical methodologies for the authentication and quality assessment of S. lateriflora-based dietary supplements have not been reported. In this study, a flow-injection/mass spectrometry fingerprinting method in combination with principal component analysis was used to survey S. lateriflora-based dietary supplements sold in the USA.

  3. Flow Injection Analysis of Mercury Using 4-(Dimethylamino Benzaldehyde-4-Ethylthiosemicarbazone as the Ionophore of a Coated Wire Electrode

    Directory of Open Access Journals (Sweden)

    Sulaiman Ab Ghani

    2012-11-01

    Full Text Available A flow injection analysis (FIA incorporating a thiosemicarbazone-based coated wire electrode (CWE was developed method for the determination of mercury(II. A 0.1 M KNO3 carrier stream with pH between 1 and 5 and flow rate of 1 mL·min−1 were used as optimum parameters. A linear plot within the concentration range of 5 × 10−6–0.1 M Hg(II, slope of 27.8 ± 1 mV per decade and correlation coefficient (R2 of 0.984 were obtained. The system was successfully applied for the determination of mercury(II in dental amalgam solutions and spiked environmental water samples. Highly reproducible measurements with relative standard deviation (RSD < 1% (n = 3 were obtained, giving a typical throughput of 30 samples·h−1.

  4. The determination of levofloxacin by flow injection analysis using UV detection, potentiometry, and conductometry in pharmaceutical preparations.

    Science.gov (United States)

    Altiokka, G; Atkosar, Z; Can, N O

    2002-10-15

    A flow injection analysis (FIA) using UV detection, potentiometry and conductometry for levofloxacin (LVF) are described in this study. The best solvent system was found to consist of 0.2 M acetate buffer at pH 3 having 10% MeOH. A flow rate of 1 ml min(-1) was pumped and active material was detected at 288 nm. The detection limit (LOD) and limit of quantification (LOQ) for FIA were calculated to be 3 x 10(-7) M (S/N = 3) and 1 x 10(-7) M (S/N = 10), respectively. In the analysis of tablets, the RSD values were found to be 0.83, 0.98 and 0.99 for FIA, potentiometric and conductometric methods, respectively. Copyright 2002 Elsevier Science B.V.

  5. A novel flow injection chemiluminescence method for automated and miniaturized determination of phenols in smoked food samples.

    Science.gov (United States)

    Vakh, Christina; Evdokimova, Ekaterina; Pochivalov, Aleksei; Moskvin, Leonid; Bulatov, Andrey

    2017-12-15

    An easily performed fully automated and miniaturized flow injection chemiluminescence (CL) method for determination of phenols in smoked food samples has been proposed. This method includes the ultrasound assisted solid-liquid extraction coupled with gas-diffusion separation of phenols from smoked food sample and analytes absorption into a NaOH solution in a specially designed gas-diffusion cell. The flow system was designed to focus on automation and miniaturization with minimal sample and reagent consumption by inexpensive instrumentation. The luminol - N-bromosuccinimide system in an alkaline medium was used for the CL determination of phenols. The limit of detection of the proposed procedure was 3·10 -8 ·molL -1 (0.01mgkg -1 ) in terms of phenol. The presented method demonstrated to be a good tool for easy, rapid and cost-effective point-of-need screening phenols in smoked food samples. Copyright © 2017 Elsevier Ltd. All rights reserved.

  6. The role of pressure drop and flow redistribution on modeling mercury control using sorbent injection in baghouse filters.

    Science.gov (United States)

    Flora, Joseph R V; Hargis, Richard A; O'Dowd, William J; Karash, Andrew; Pennline, Henry W; Vidic, Radisav D

    2006-03-01

    A mathematical model based on simple cake filtration theory was coupled to a previously developed two-stage mathematical model for mercury (Hg) removal using powdered activated carbon injection upstream of a baghouse filter. Values of the average permeability of the filter cake and the filter resistance extracted from the model were 4.4 x 10(-13) m2 and 2.5 x 10(-4) m(-1), respectively. The flow is redistributed during partial cleaning of the filter, with flows higher across the newly cleaned filter section. The calculated average Hg removal efficiency from the baghouse is lower because of the high mass flux of Hg exiting the filter in the newly cleaned section. The model shows that calculated average Hg removal is affected by permeability, filter resistance, fraction of the baghouse cleaned, and cleaning interval.

  7. The role of pressure drop and flow redistribution on modeling mercury control using sorbent injection in baghouse filters

    Energy Technology Data Exchange (ETDEWEB)

    Joseph R.V. Flora; Richard A. Hargis; William J. O' Dowd; Andrew Karash; Henry W. Pennline; Radisav D. Vidic [University of South Carolina, Columbia, SC (United States). Department of Civil and Environmental Engineering

    2006-03-15

    A mathematical model based on simple cake filtration theory was coupled to a previously developed two-stage mathematical model for mercury (Hg) removal from coal combustion using powdered activated carbon injection upstream of a baghouse filter. Values of the average permeability of the filter cake and the filter resistance extracted from the model were 4.4 x 10{sup -13}m{sup 2} and 2.5 x 10{sup -4}m{sup -1}, respectively. The flow is redistributed during partial cleaning of the filter, with flows higher across the newly cleaned filter section. The calculated average Hg removal efficiency from the baghouse is lower because of the high mass flux of Hg exiting the filter in the newly cleaned section. The model shows that calculated average Hg removal is affected by permeability, filter resistance, fraction of the baghouse cleaned, and cleaning interval. 17 refs., 8 figs., 2 tabs.

  8. A flow-injection system coupled to a micro-guard cartridge for monitoring a vinification process.

    Science.gov (United States)

    Vidigal, Susana S M P; Rangel, António O S S

    2014-01-01

    The present paper describes a flow-injection system coupled to a Micro-Guard cartridge and a miniaturized optical CCD detection system used to monitor the sugars (glucose/fructose) and ethanol content during alcoholic fermentation. The carrier stream (mobile phase) is composed of an aqueous sulfuric acid solution. The flow parameters were studied in order to obtain a good resolution and a wide dynamic concentration range, with a good repeatability. The relative standard deviation (RSD) obtained was inferior to 4%, for n = 3. It was possible to achieve a linear range of up to 12 g L(-1) of sugars and up to 2% (v/v) of ethanol with a detection limit of 2.3 g L(-1) and 0.4% (v/v), for sugars and ethanol concentrations, respectively. The proposed system was successfully applied to monitor a vinification process by the quantification of sugars and ethanol, and also in some finished port wines.

  9. Shear flow and carbon nanotubes synergistically induced nonisothermal crystallization of poly(lactic acid) and its application in injection molding.

    Science.gov (United States)

    Tang, Hu; Chen, Jing-Bin; Wang, Yan; Xu, Jia-Zhuang; Hsiao, Benjamin S; Zhong, Gan-Ji; Li, Zhong-Ming

    2012-11-12

    The effect of shear flow and carbon nanotubes (CNTs), separately and together, on nonisothermal crystallization of poly(lactic acid) (PLA) at a relatively large cooling rate was investigated by time-resolved synchrotron wide-angle X-ray diffraction (WAXD) and polarized optical microscope (POM). Unlike flexible-chain polymers such as polyethylene, and so on, whose crystallization kinetics are significantly accelerated by shear flow, neat PLA only exhibits an increase in onset crystallization temperature after experiencing a shear rate of 30 s(-1), whereas both the nucleation density and ultimate crystallinity are not changed too much because PLA chains are intrinsically semirigid and have relatively short length. The breaking down of shear-induced nuclei into point-like precursors (or random coil) probably becomes increasingly active after shear stops. Very interestingly, a marked synergistic effect of shear flow and CNTs exists in enhancing crystallization of PLA, leading to a remarkable increase of nucleation density in PLA/CNT nanocomposite. This synergistic effect is ascribed to extra nuclei, which are formed by the anchoring effect of CNTs' surfaces on the shear-induced nuclei and suppressing effect of CNTs on the relaxation of the shear-induced nuclei. Further, this interesting finding was deliberately applied to injection molding, aiming to improve the crystallinity of PLA products. As expected, a remarkable high crystallinity in the injection-molded PLA part has been achieved successfully by the combination of shear flow and CNTs, which offers a new method to fabricate PLA products with high crystallinity for specific applications.

  10. Flow injection on-line spectrophotometric determination of thorium(IV) after preconcentration on XAD-4 resin impregnated with oxytetracycline

    Energy Technology Data Exchange (ETDEWEB)

    Shahida, Shabnam; Khan, Muhammad Haleem [Univ. of Azad Jammu and Kashmir, Muzaffarabad (Pakistan). Dept. of Chemistry; Ali, Akbar [Pakistan Institute of Nuclear Science and Technology, Islamabad (Pakistan). Chemistry Div.

    2014-02-15

    A very sensitive, selective and simple flow injection time-based method was developed for on-line preconcentration and determination of thorium(IV) at micro g L{sup -1} levels in environmental samples. The system operation was based on thorium(IV) ion retention at pH 4.0 in the minicolumn at a flow rate of 15.2 mL min{sup -1}. The trapped complex was then eluted with 3.6 mol L{sup -1} HCl at a flow rate of 4.9 mL min{sup -1}. The amount of thorium(IV) in the eluate was measured spectrophotometrically at 651 nm using arsenazo-III solution (0.05 % in 3.6 mol L{sup -1} HCl stabilized with 1 % triton X-100, 4.9 mL min{sup -1}) as colorimetric reagent. All chemical, and flow injection variables were optimized for the quantitative preconcentration of metal and a study of interference level of various ions was also carried out. The system offered low backpressure and improved sensitivity and selectivity. At a preconcentration time of 60 s and a sample frequency of 40 h{sup -1}, the enhancement factor was 97, the detection limit was 0.25 μg L{sup -1}, and the precision expressed as relative standard deviation was 1.08 % (at 50 μg L{sup -1}), whereas for 300 s of the preconcentration time and a sample frequency of 10 h{sup -1}, the enhancement factor of 357, the detection limit (3s) of 0.069 μg L{sup -1} and the precision of 1.32 % (at 10 μg L{sup -1}) was reported. The accuracy of the developed method was sufficient and evaluated by the analysis of certified reference material IAEA-SL-1 (Lake Sediment) and spiked water samples.

  11. DETERMINATION OF FREE CATECHOLAMINES IN URINE BY TANDEM AFFINITY/ION-PAIR CHROMATOGRAPHY AND FLOW INJECTION ANALYSIS

    Science.gov (United States)

    Thomas, David H.; Taylor, Jay D.; Barnaby, Omar S.; Hage, David S.

    2008-01-01

    Background A system was developed for the simultaneous measurement in urine of free catecholamines (i.e., dopamine, norepinephrine, epinephrine) and creatinine (i.e., an indicator of urine output and volume). This method was based on the use of tandem affinity/ion-pair HPLC and flow injection analysis. Methods The free catecholamines were extracted directly from urine by using an on-line phenylboronic acid affinity column. The extracted solutes were then separated and measured by ion-pair chromatography followed by amperometric detection. Creatinine was measured by an on-line flow injection analysis system based on the Jaffe reaction, which analyzed creatinine as it eluted non-retained from the phenylboronic acid column. Results Various factors were considered in the design and optimization of the phenylboronic acid column, the tandem affinity/ion-pair HPLC columns and the flow injection analysis system. The total analysis time for the final combined system was approximately 16 min per injection at 1 ml/min. This method was found to have good agreement with the expected results for control urine samples. The limits of detection for 20 μl samples (S/N = 3.0) were 1.8, 1.0 and 4.3 μg/l for norepinephrine, epinephrine and dopamine, respectively, while the limit of detection of creatinine was 5.0 mg/l. The linear response of this method extended over a 450 to 930-fold range in concentration for the catecholamines and covered the range of clinical interest. The within-day precision of this method was ±2.0−2.7%. Conclusions The ability of this method to simultaneously monitor both creatinine and other analytes makes this HPLC/FIA system an attractive method for use in monitoring urinary compounds. With this approach it was possible to provide fast results for small volumes of random urine samples that were collected as part of a psychological study. The same method could also be utilized with 12 or 24 h urine specimens. PMID:18773884

  12. An environmental friendly method for the automatic determination of hypochlorite in commercial products using multisyringe flow injection analysis.

    Science.gov (United States)

    Soto, N Ornelas; Horstkotte, B; March, J G; López de Alba, P L; López Martínez, L; Cerdá Martín, V

    2008-03-24

    A multisyringe flow injection analysis system was used for the determination of hypochlorite in cleaning agents, by measurement of the native absorbance of hypochlorite at 292 nm. The methodology was based on the selective decomposition of hypochlorite by a cobalt oxide catalyst giving chloride and oxygen. The difference of the absorbance of the sample before and after its pass through a cobalt oxide column was selected as analytical signal. As no further reagent was required this work can be considered as a contribution to environmental friendly analytical chemistry. The entire analytical procedure, including in-line sample dilution in three steps was automated by first, dilution in a stirred miniature vessel, second by dispersion and third by in-line addition of water using multisyringe flow injection technique. The dynamic concentration range was 0.04-0.78 gL(-1) (relative standard deviation lower than 3%), where the extension of the hypochlorite decomposition was of 90+/-4%. The proposed method was successfully applied to the analysis of commercial cleaning products. The accuracy of the method was established by iodometric titration.

  13. Biosensing of glucose in flow injection analysis system based on glucose oxidase-quantum dot modified pencil graphite electrode.

    Science.gov (United States)

    Sağlam, Özlem; Kızılkaya, Bayram; Uysal, Hüseyin; Dilgin, Yusuf

    2016-01-15

    A novel amperometric glucose biosensor was proposed in flow injection analysis (FIA) system using glucose oxidase (GOD) and Quantum dot (ZnS-CdS) modified Pencil Graphite Electrode (PGE). After ZnS-CdS film was electrochemically deposited onto PGE surface, GOD was immobilized on the surface of ZnS-CdS/PGE through crosslinking with chitosan (CT). A pair of well-defined reversible redox peak of GOD was observed at GOD/CT/ZnS-CdS/PGE based on enzyme electrode by direct electron transfer between the protein and electrode. Further, obtained GOD/CT/ZnS-CdS/PGE offers a disposable, low cost, selective and sensitive electrochemical biosensing of glucose in FIA system based on the decrease of the electrocatalytic response of the reduced form of GOD to dissolved oxygen. Under optimum conditions (flow rate, 1.3mL min(-1); transmission tubing length, 10cm; injection volume, 100μL; and constant applied potential, -500mV vs. Ag/AgCl), the proposed method displayed a linear response to glucose in the range of 0.01-1.0mM with detection limit of 3.0µM. The results obtained from this study would provide the basis for further development of the biosensing using PGE based FIA systems. Copyright © 2015 Elsevier B.V. All rights reserved.

  14. Fabrication of an Amperometric Flow-Injection Microfluidic Biosensor Based on Laccase for In Situ Determination of Phenolic Compounds

    Directory of Open Access Journals (Sweden)

    Juan C. Gonzalez-Rivera

    2015-01-01

    Full Text Available We aim to develop an in situ microfluidic biosensor based on laccase from Trametes pubescens with flow-injection and amperometry as the transducer method. The enzyme was directly immobilized by potential step chronoamperometry, and the immobilization was studied using cyclic voltammetry and electrochemical impedance spectroscopy. The electrode response by amperometry was probed using ABTS and syringaldazine. A shift of interfacial electron transfer resistance and the electron transfer rate constant from 18.1 kΩ to 3.9 MΩ and 4.6 × 10−2 cm s−1 to 2.1 × 10−4 cm s−1, respectively, evidenced that laccase was immobilized on the electrode by the proposed method. We established the optimum operating conditions of temperature (55°C, pH (4.5, injection flow rate (200 µL min−1, and applied potential (0.4 V. Finally, the microfluidic biosensor showed better lower limit of detection (0.149 µM and sensitivity (0.2341 nA µM−1 for ABTS than previous laccase-based biosensors and the in situ operation capacity.

  15. Flow injection amperometric determination of persulfate in cosmetic products using a Prussian Blue film-modified electrode

    Directory of Open Access Journals (Sweden)

    Nelson R. Stradiotto

    2003-09-01

    Full Text Available A flow-injection system with a glassy carbon disk electrode modified with Prussian Blue film is proposed for the determination of persulfate in commercial samples of hair bleaching boosters by amperometry. The detection was obtained by chronoamperometric technique and the sample is injected into the electrochemical cell in a wall jet configuration. Potassium chloride at concentration of 0.1 mol L-1 acted as sample carrier at a flow rate of 4.0 mL min-1 and supporting-electrolyte. For 0.025 V (vs. Ag/AgCl applied voltage, the proposed system handles ca. 160 samples per hour (1.0 10-4 - 1.0 10-3 mol L-1 of persulfate, consuming about 200 μL sample and 11 mg KCl per determination. Typical linear correlations between electrocatalytic current and persulfate concentration was ca. 0.9998. The detection limit is 9.0 10-5 mol L-1 and the calculated amperometric sensibility 3.6 103 μA L mol-1. Relative standard deviation (n =12 of a 1.0 10-4 mol L-1 sample is about 2.2%. The method was applied to persulfate determination in commercial hair-bleaching samples and results are in agreement with those obtained by titrimetry at 95% confidence level and good recoveries (95 - 112% of spiked samples were found.

  16. Chemically modified ion-sensitive field-effect transistors: elimination of the liquid junction potential in a double sensor flow-injection analysis cell

    NARCIS (Netherlands)

    Cobben, P.L.H.M.; Cobben, Peter L.H.M.; Egberink, Richard J.M.; Bomer, Johan G.; Schouwenaar, Robert; Brzozka, Zbigniew; Bergveld, Piet; Reinhoudt, David; Bos, M.

    1993-01-01

    A flow-through cell was designed that can be used for flow-injection analysis with two chemically modified ion-sensitive field-effect transistors (CHEMFETs) in close proximity. This offers the possibility of a differential measurement without influence of the liquid junction potential. The

  17. Understanding the Fundamental Roles of Momentum and Vorticity Injections in Flow Control

    Science.gov (United States)

    2016-09-02

    2010 Feedback control of unstable steady states of flow past a flat plate using reduced-order estimators. J. Fluid Mech. 645, 447–478. Åkervik, E...Oxford University Press. Deng, S., Jiang, L. & Liu, C. 2007 DNS for flow separation control around an airfoil by pulsed jets. Computers and Fluids 36 (6...Distribution approved for public release. Owen, J. P., Li, Y.-O., Ziv, E., Strominger, Z., Gold , J., Bukhpun, P., Wakahiro, M., Friedman, E. J., Sherr, E. H

  18. Intravitreal injection

    Science.gov (United States)

    Antibiotic - intravitreal injection; Triamcinolone - intravitreal injection; Dexamethasone - intravitreal injection; Lucentis - intravitreal injection; Avastin - intravitreal injection; Bevacizumab - intravitreal injection; Ranibizumab - intravitreal injection; ...

  19. Peripheral intravenous power injection of iodinated contrast media through 22G and 20G cannulas: can high flow rates be achieved safely? A clinical feasibility study.

    Science.gov (United States)

    Schwab, S A; Uder, M; Anders, K; Heinrich, M C; Kuefner, M A

    2009-04-01

    Modern examination protocols for computed tomography (CT) often require high injection rates of iodinated contrast media (CM). The purpose of this study was to evaluate the maximum achievable flow rates and stability of different peripheral intravenous catheters (IVC) in vitro and to assess the feasibility of higher injection rates through small IVC in vivo. For in vitro experiments flow measurements followed by high pressure testing of different types of IVC (22, 20, and 18 gauge [G]) were performed. For the in vitro study 91 patients with already inserted 22 or 20G IVC who had been referred for CT received Iopamidol (300 mg iodine/ml) at flow rates between 2 and 5 ml/sec. Complications were documented. The maximal achievable flow rate of the tested IVC in vitro ranged from 5 to 8 ml/sec. No damage was observed during in vitro testing. The initially targeted in vivo flow rate was dropped in 33 of 91 (36 %) patients because the IVC could not be flushed adequately with saline before CM injection. Extravasation of CM occurred in 2 cases. In the remaining 58 patients the standard CT protocol was performed with flow rates of 3 ml/sec through 22G IVC and 5 ml/sec through 20G IVC, respectively. In this group, the extravasation of CM was observed twice (p > 0.05). Even with highly viscous CM, high flow rates can be applied in vitro in 22, 20, and 18G IVC without risking material damage. In vivo power injection of iodinated CM through 22G and 20G IVC seems to be safely achievable in the majority of patients with flow rates of up to 3 ml/sec and 5 ml/sec. Extravasation rates do not differ significantly between patients with high-flow or low-flow injections.

  20. Injection of Drag Reducing Additives Into Turbulent Water Flows. Mixing Experiments and Newtonian Burst Frequency.

    Science.gov (United States)

    1987-04-01

    Heterogeneous drag reduction in turbulent pipe flow. The Influence of Polymer Additives on Velocity and Temperature Fields, B. Gampert , ed., Springer-Verlag...Temperature Fields, B. Gampert , ed., Springer-Verlag, Berlin. Kim, H.T., S.J. Kline and W.C. Reynolds, 1971. The production of turbulence near a smooth

  1. Fuel property and fuel temperature effects on internal nozzle flow, atomization and cyclic spray fluctuations of a direct injection spark ignition–injector

    OpenAIRE

    Zigan, Lars; Shi, Jun-Mei; Krotow, Ivan; Schmitz, Ingo; Wensing, Michael; Leipertz, Alfred

    2013-01-01

    The effect of fuel properties and fuel temperature on the behaviour of the internal nozzle flow, atomization and cyclic spray fluctuations is examined for a three-hole direct injection spark ignition injector by combining numerical simulation of the nozzle flow with macroscopic and microscopic spray visualization techniques. A dominant influence of the liquid fuel viscosity on the highly unsteady, cavitating nozzle flow and spray formation was observed. A reduced viscosity (or larger Reynolds...

  2. Application of Doehlert matrix to the study of flow injection procedure for selenium (IV) determination.

    Science.gov (United States)

    Hellal, F; Dachraoui, M

    2004-07-08

    A method for the rapid determination of selenium is reported. It is based on the injection of selenium sample into a stream of KI and subsequent measurement of the increase of the absorption at 290nm due to the formation of I(3)(-). A Doehlert matrix was applied for the determination of the optimal working conditions. With the developed method, a linear calibration curve from 1 to 10ppm was obtained. For the analysis of semiconducting thin layers of CuInSe(2) (CIS), a cationic resin was added to the sample solution in order to eliminate the effect of copper and indium on the absorbance values. With the developed procedure a sample throughput of 36 samples per hour and a relative standard deviation 1.1% was achieved.

  3. Flow-Injection Coulometric Detection Based on Ion Transfer and Its Application to the Determination of Chlorpromazine

    Directory of Open Access Journals (Sweden)

    Concepción Sánchez-Pedreño

    2008-06-01

    Full Text Available A flow-injection coulometric method for the determination of chlorpromazine based on ion transfer into a plasticized poly(vinyl chloride (PVC membrane, was developed. The detector used consists of a flow-through cell that incorporates a plasticized poly(vinyl chloride (PVC membrane which contains tetrabutylammonium tetraphenylborate as electrolyte. The membrane is located between the flowing solution and an inner aqueous electrolyte solution. Two pairs of electrodes, each pair formed by a reference electrode and a working electrode, are used, one pair in each solution. The potential between the reference electrodes was controlled by a four-electrode potentiostat with ohmic drop compensation. A potential step capable of producing the transfer of the chlorpromazine ion into the membrane was applied during the passage of a wide portion of sample plug through the cell and the corresponding quantity of the electricity was measured. In the selected conditions, a linear relationship was observed between the quantity of electricity and chlorpromazine concentrations over a range of 1x10-6 -1x10-4 M. The detection limit was 2 x 10-7 M. Good repeatability and between-day reproducibility was obtained. No interference was observed on the part of some common ions and pharmaceutical excipients. The method proposed was applied satisfactorily to the determination of chlorpromazine in pharmaceuticals and human urine.

  4. Numerical Analysis on the Influence of Thermal Effects on Oil Flow Characteristic in High-Pressure Air Injection (HPAI Process

    Directory of Open Access Journals (Sweden)

    Hu Jia

    2012-01-01

    Full Text Available In previous laboratory study, we have shown the thermal behavior of Keke Ya light crude oil (Tarim oilfield, branch of CNPC for high-pressure air injection (HPAI application potential study. To clarify the influences of thermal effects on oil production, in this paper, we derived a mathematical model for calculating oil flow rate, which is based on the heat conduction property in porous media from the combustion tube experiment. Based on remarkably limited knowledge consisting of very global balance arguments and disregarding all the details of the mechanisms in the reaction zone, the local governing equations are formulated in a dimensionless form. We use finite difference method to solve this model and address the study by way of qualitative analysis. The time-space dimensionless oil flow rate (qD profiles are established for comprehensive studies on the oil flow rate characteristic affected by thermal effects. It also discusses how these findings will impact HPAI project performances, and several guidelines are suggested.

  5. Wavelength selection in injection-driven Hele-Shaw flows: A maximum amplitude criterion

    Science.gov (United States)

    Dias, Eduardo; Miranda, Jose

    2013-11-01

    As in most interfacial flow problems, the standard theoretical procedure to establish wavelength selection in the viscous fingering instability is to maximize the linear growth rate. However, there are important discrepancies between previous theoretical predictions and existing experimental data. In this work we perform a linear stability analysis of the radial Hele-Shaw flow system that takes into account the combined action of viscous normal stresses and wetting effects. Most importantly, we introduce an alternative selection criterion for which the selected wavelength is determined by the maximum of the interfacial perturbation amplitude. The effectiveness of such a criterion is substantiated by the significantly improved agreement between theory and experiments. We thank CNPq (Brazilian Sponsor) for financial support.

  6. The analysis of the flow with water injection in a centrifugal compressor stage using CFD simulation

    Science.gov (United States)

    Michal, Tomášek; Richard, Matas; Tomáš, Syka

    2017-09-01

    This text deals with the principle of direct cooling of the pressure gas in a centrifugal compressor based on evaporation of the additional fluid phase in a control domain. A decrease of the gas temperature is reached by taking the heat, which is required for evaporation of the fluid phase. The influence of additional fluid phase on the parameters of the multiphase flow is compared with the ideal gas simulation in the defined domain and with the same boundary conditions.

  7. Study of the influence of the turbulent boundary conditions of a flow with parietal injection; Etude de l'influence des conditions aux limites turbulentes d'un ecoulement avec injection parietale

    Energy Technology Data Exchange (ETDEWEB)

    Chaouat, B.

    1998-07-01

    Numerical simulations of flows inside a solid propellant rocket engine with parietal injection are performed using the numerical resolution of Navier-Stokes equations in a k-{epsilon} turbulence model. Boundary conditions are defined considering laminar and turbulent fluid injections on the wall. In parallel, a Couette-type model is used to determine the velocity profile near the wall and the wall constraint for a laminar fluid injection. An analysis of simulations shows the influence of boundary conditions on the transition of the flow from the laminar to the turbulent regime, on the velocity profile near the wall, and on the evolution of Reynolds pressures. The average velocity profile is well reproduced but the first-order k-{epsilon} turbulence model shows limitations for the reproduction of turbulent pressure levels. A second-order Reynolds pressure model should be more appropriate. (J.S.)

  8. Evaluation of flow injection analysis method with spectrophotometric detection for the determination of atrazine in soil extracts.

    Science.gov (United States)

    Martins, Elisandra C; Melo, Vander De F; Abate, Gilberto

    2016-09-01

    A method for determining atrazine in soil extracts was evaluated by flow injection analysis with spectrophotometric detection. The method is based on the reaction of atrazine with pyridine in an acid medium followed by the reaction with NaOH and sulfanilic acid. Several analytical conditions were previously studied and optimized. Under the best conditions of analysis, the limits of detection and quantification were 0.15 and 0.45 mg L(-1), respectively, for a linear response between 0.50 and 2.50 mg L(-1), and a sampling throughput of 21 determinations per hour. Using the standard addition method, the maximum relative standard deviation of 17% and recovery values between 80 and 100% were observed for three extracts from soil samples with different composition. The proposed method is simple, low-cost and easy to use, and can be employed for studies involving atrazine in soil samples or for screening of atrazine in soils.

  9. TiO2 nanotube sensor for online chemical oxygen demand determination in conjunction with flow injection technique.

    Science.gov (United States)

    Li, Xuejin; Yin, Weiping; Li, Jianyong; Bai, Jing; Huang, Ke; Li, Jinhua; Zhou, Baoxue

    2014-06-01

    A simple, rapid and environmental friendly online chemical oxygen demand (COD) analytical method based on TiO2 nanotube sensor in conjunction with the flow injection technique was proposed to determine the COD of aqueous samples, especially for refractory organics, low-concentration wastewater, and surface water. The new method can overcome the drawbacks of the conventional COD determination methods. The results show that with the new method, each analysis takes only about 1 to 3 min, the linear range is up to 1 to 500 mg x L(-1) of the compound of interest, and the detection limit is 1 mg x L(-1). The COD values obtained by the proposed method are more accurate than those obtained by the conventional method.

  10. Heat transfer analysis of Jeffery fluid flow over a stretching sheet with suction/injection and magnetic dipole effect

    Directory of Open Access Journals (Sweden)

    A. Zeeshan

    2016-09-01

    Full Text Available The purpose of the present paper was to investigate the flow and heat transfer of Jeffery fluid past a linearly stretching sheet with the effect of a magnetic dipole. The governing differential equations of motion and heat transfer are transformed into nonlinear coupled ordinary differential equations (ODEs using appropriate similarity transformations. Then the ODEs are solved by adopting two different schemes, Runge–Kutta with shooting technique and series solution based on GA and NM. The effect of various physical parameters including ferromagnetic interaction parameter (β, Deborah number (γ1, Prandtl number (Pr, suction/injection parameter (S, ratio of relaxation to retardation times (λ2 on velocity and temperature profiles is illustrated graphically and in tabular form by considering two types of thermal process namely prescribed surface temperature (PST and prescribed heat flux (PHF. Comparison with available results for particular cases is found an excellent agreement.

  11. Prediction of electron concentration reductions in re-entry flow fields due to electrophilic liquid and water injection.

    Science.gov (United States)

    Pergament, H. S.; Mikatarian, R. R.; Kurzius, S. C.

    1972-01-01

    Discussion of an analytical model which leads to predictions of reductions in electron concentrations in reentry flow fields due to the injection of electrophilic liquids and water. The processes incorporated into the model are: penetration and breakup of the liquid jet, droplet acceleration and vaporization, expansion of the liquid spray due to droplet vaporization, electrophilic vapor diffusion, heterogeneous and homogeneous charged species recombination kinetics and homogeneous electron attachment kinetics. Spray boundary calculations are shown to be in good agreement with photographic observations of water and Freon E-3 sprays in wind tunnel tests of a scale model RAM C-III flight vehicle. Fixed-bias electrostatic probe data taken during the RAM C-III flight are interpreted in terms of effective jet penetration distances - which are shown to be consistent with calculations using the present model.

  12. SEMI-CONTINUOUS DETERMINATION OF NO2 IN PASSIVE DIFFUSERS BY FLOW INJECTION/UV-VIS SPECTROPHOTOMETRY

    Directory of Open Access Journals (Sweden)

    Iliana M. de la Garza-Rodríguez

    2015-06-01

    Full Text Available In this work the development of a semi-automated method by flow injection for spectrophotometric indirect determination of NO2, is described. The gas of environmental importance is captured through passive diffusers built in the laboratory, where it undergoes a reaction with triethanolamine to form nitrite ions in relation 1:1, which are determined after the derivatization with sulfanilamide and N-(1-naphthyl ethylenediamine. It’s concluded that the proposal method is quick and easy, as well as sensitive and selective to determine the chemical specie of interest. The estimated NO2 concentration in the air of Saltillo in Coahuila was 2.6 ± 0.3 mg m-3, which was above the maximum recommended by NOM-023-SSA1-1993 norm.

  13. Determination of Trace Amounts of Chromium(III) in Water Samples Using Online Flow Injection Catalytic Spectrophotometry

    Science.gov (United States)

    Zhao, Z. X.; Zhang, X. S.

    2017-01-01

    A new online flow injection spectrophotometric method for the determination of trivalent chromium was developed. This method is based on the property of trivalent chromium to be a catalyst for the oxidation of Indigo Carmine (IC) with potassium periodate and to lose its color in the presence of ethylenediaminetetraacetic acid and sodium tripolyphosphate. It was shown that Tween-20 serves as an additional accelerator of the catalytic oxidation. The linear dynamic range of the determination of Cr(III) was 1-40.0 μg/L, while the limit of detection was 0.05 μg/L. The correlation coefficient r was 0.998, while the relative standard deviation for 5 μg/L of the Cr(III) solution was 3.83%. The feasibility of this method was checked by its application to trivalent chromium determination in real water samples.

  14. Flow injection analysis of phenolic compounds with carbon paste electrodes modified with tyrosinase purchased from different companies

    Energy Technology Data Exchange (ETDEWEB)

    Lindgren, A.; Emneus, J.; Csoeregi, E.; Gorton, L.; Marko-Varga, G. [Univ. of Lund (Sweden); Ruzgas, T. [Inst. of Biochemistry, Vilnius (Lithuania)

    1996-05-01

    Tyrosinase-modified carbon paste electrodes were prepared using lyophilised powder of the enzyme purchased from different companies. The selectivity of these electrodes for nine phenolic compounds, including six substituted catechols, has been studied. The signals obtained for catechol were always higher than those found for other phenolic compounds. Cyclic voltammetry and flow injection measurements indicated that the response of the tyrosinase-modified carbon paste electrodes was limited by the rate of the enzymatic oxidation of catechols. Different approaches of past electrode preparation have been studied and compared. Direct mixing of enzyme into the graphite powder doped with the osmium based mediator, resulted in the highest sensitivity for the studied substrates. However, substrate selectivity was found to be dependent on the source of enzyme used for electrode preparation.

  15. Flow-injection spectrophotometric determination of tetracycline and doxycycline in pharmaceutical formulations using chloramine-T as oxidizing agent

    Directory of Open Access Journals (Sweden)

    José L. Rufino

    2009-01-01

    Full Text Available A flow-injection (FI spectrophotometric procedure is proposed for tetracycline (TC and doxycycline (DXC determination in pharmaceuticals. The method is based on the reaction of oxidation of these drugs by chloramine-T in alkaline medium producing red color products (λmax = 535 and 525 nm. Beer´s law is obeyed in the concentration range from 6.62 x 10-5 to 7.72 x 10-4 mol L-1 and 5.37 x 10-5 to 7.16 x 10-4 mol L-1 for TC and DXC, respectively. The analytical frequency was 50 h"1 and 45 h-1 for TC and DXC, respectively. The results obtained by the proposed method were in good agreement with those obtained by the official method at 95% confidence level.

  16. A novel dynamic approach for automatic microsampling and continuous monitoring of metal ion release from soils exploiting a dedicated flow-through microdialyser

    Energy Technology Data Exchange (ETDEWEB)

    Miro, Manuel [University of the Balearic Islands, Department of Chemistry, Illes Balears (Spain); Jimoh, Modupe; Frenzel, Wolfgang [Technische Universitaet Berlin, Institut fuer Technischen Umweltschutz, Berlin (Germany)

    2005-05-01

    In this paper, a novel concept is presented for automatic microsampling and continuous monitoring of metal ions in soils with minimum disturbance of the sampling site. It involves a hollow-fiber microdialyser that is implanted in the soil body as a miniaturized sensing device. The idea behind microdialysis in this application is to mimic the function of a passive sampler to predict the actual, rather than potential, mobility and bioavailability of metal traces. Although almost quantitative dialysis recoveries were obtained for lead ({>=} 98%) from aqueous model solutions with sufficiently long capillaries (l{>=}30 mm, 200 {mu}m i.d.) at perfusion rates of 2.0 {mu}L min{sup -1}, the resistance of an inert soil matrix was found to reduce metal uptake by 30%. Preliminary investigation of the potential of the microdialysis analyser for risk assessment of soil pollution, and for metal partitioning studies, were performed by implanting the dedicated probe in a laboratory-made soil column and hyphenating it with electrothermal atomic absorption spectrometry (ETAAS), so that minute, well-defined volumes of clean microdialysates were injected on-line into the graphite furnace. A noteworthy feature of the implanted microdialysis-based device is the capability to follow the kinetics of metal release under simulated natural scenarios or anthropogenic actions. An ancillary flow set-up was arranged in such a way that a continuous flow of leaching solution - mild extractant (10{sup -2} mol L{sup -1} CaCl{sub 2}), acidic solution (10{sup -3} mol L{sup -1} HNO{sub 3}), or chelating agent (10{sup -4} or 10{sup -2} mol L{sup -1} EDTA) - was maintained through the soil body, while the concentration trends of inorganic (un-bound) metal species at the soil-liquid interface could be monitored at near real-time. Hence, relevant qualitative and quantitative information about the various mobile fractions is obtained, and metal-soil phase associations can also be elucidated. Finally

  17. Regional cerebral blood flow measurements in schizophrenics by /sup 133/Xe inhalation and intra-venous injection method

    Energy Technology Data Exchange (ETDEWEB)

    Matsuda, Hiroshi; Seki, Hiroyasu; Sumiya, Hisashi; Ishida, Hiroko; Taki, Junichi; Hisada, Kinichi; Kurachi, Masayoshi; Kobayashi, Katsuji; Yamaguchi, Nariyoshi (Kanazawa Univ. (Japan). School of Medicine)

    1984-12-01

    Regional cerebral blood flow measurements were performed in 25 schizophrenic patients and 25 healthy volunteers by /sup 133/Xe inhalation and intra-venous injection method. Schizophrenic patients were classified into the following three groups. Group I: 8 patients without auditory hallucination measured by 2-dimensional /sup 133/Xe inhalation method. Group II: 6 patients with auditory hallucination measured by the same method as in Group I. Group III: 11 patients, including 2 patients with auditory hallucination measured by 3-dimensional /sup 133/Xe intra-venous injection method at the level of OM+5 cm. Bilateral regional percent values, which were obtained by dividing regional values by hemispheric mean or sectional mean values, for frontal lobes in Group I and II were significantly lower than those in the controls. In addition, bilateral regional percent values for bilateral temporal lobes in Group II were significantly higher than those in the controls. In Group III, regional percent values for right frontal lobes and those for posterior part of central gray matter showed significant decrease and increase, respectively. These findings would suggest that the negative symptoms of schizophrenia are related to the hypofrontal and positive ones to the hypertemporoparietal activity.

  18. Spectrophotometric determination of trace aluminium content in parenteral solutions by combined cloud point preconcentration-flow injection analysis.

    Science.gov (United States)

    Sombra, L; Luconi, M; Silva, M F; Olsina, R A; Fernandez, L

    2001-07-01

    A cloud point preconcentration and flow injection (FI) analysis methodology for aluminium(III) determination has been developed. The analyte in the initial aqueous solution was complexed with Chrome Azurol S (CAS) in the presence of the cationic surfactant benzyldimethyltetradecylammonium chloride (BDTAC). The absorption spectroscopic characteristics of the ternary complex [Al(III)-CAS-BDTAC] were examined in detail. The preconcentration step was carried out by means of the non-ionic surfactant polyethylene glycol p-nonylphenyl ether (PONPE 7.5). The enriched analyte solution was injected into an FI system using an HPLC pump. The chemical variables affecting the analytical performance of the combined methodology were studied and optimised. The developed approach was successfully applied to the determination of trace amounts of aluminium in parenteral solutions without previous treatment. Under the optimum experimental conditions, 99.9% extraction was achieved for a preconcentration factor of 50. The limit of detection was 1.12 x 10(-7) mol(-1). The calibration plot was linear over at least two orders of magnitude of aluminium concentration. The developed coupled methodology, which thoroughly satisfies the typical requirements for pharmaceutical control processes, is appropriate for monitoring the aluminium concentration in parenteral nutrition.

  19. FLOW INJECTION ANALYSIS SYSTEM COUPLED WITH ICP-EOS FOR DETERMINATION OF SOME METALLIC ELEMENTS IN DRINKING WATER

    Directory of Open Access Journals (Sweden)

    Cristina Dinu

    2009-06-01

    Full Text Available The European Drinking Water Directive (98/83/EC, transposed in Romanian Legislation as Low 458/2002, amended by Low 311/2004, imposes the limit of concentration for metallic elements in water intended for human consumption. The toxic metals arsenic and selenium are among these elements and the limit value is 10 μg/L. In the paper there are presented the working conditions for determination of As and Se from drinking water using modern techniques based on the fl ow injection-hydride generation with the inductively coupled plasma atomic emission spectrometry (FIAS-ICP-EOS. The analyses were performed on Optima 5300 DV Perkin Elmer equipment with FIAS 400 Flow Injection System, Perkin Elmer type. For the hydride generation two types of solution were used: 10% (v/v HCl as a carrier solution and 0.2 % NaBH4 in 0.05%NaOH solution as a reducing agent [1]. The treatment step of the samples and standard solutions consisted in reducing with mixed solutions of KI and ascorbic acid in acidic condition (HCl for As and only with HCl and high temperature for Se [2,3]. The paper contains the characteristic parameters of the methods, such as: low detection limit, quantifi cation limit, repeatability, precision, recovery, which were evaluated using Certifi ed Reference Materials for each element.

  20. Electrochemical study and flow injection analysis of paracetamol in pharmaceutical formulations based on screen-printed electrodes and carbon nanotubes

    Energy Technology Data Exchange (ETDEWEB)

    Fanjul-Bolado, Pablo [DropSens, S.L., Edificio Severo Ochoa, Campus El Cristo, 33006 Oviedo, Asturias (Spain); Lamas-Ardisana, Pedro Jose [Departamento de Quimica Fisica y Analitica, Universidad de Oviedo, Julian Claveria 8, 33006 Oviedo, Asturias (Spain); Hernandez-Santos, David [DropSens, S.L., Edificio Severo Ochoa, Campus El Cristo, 33006 Oviedo, Asturias (Spain); Costa-Garcia, Agustin, E-mail: costa@fq.uniovi.es [Departamento de Quimica Fisica y Analitica, Universidad de Oviedo, Julian Claveria 8, 33006 Oviedo, Asturias (Spain)

    2009-04-13

    Acetaminophenol or paracetamol is one of the most commonly used analgesics in pharmaceutical formulations. Acetaminophen is electroactive and voltammetric mechanistic studies for the electrode processes of the acetaminophenol/N-acetyl-p-quinoneimine redox system are presented. Carbon nanotubes modified screen-printed electrodes with enhanced electron transfer properties are used for the study of the electrochemical-chemical oxidation mechanism of paracetamol at pH 2.0. Quantitative analysis of paracetamol by using its oxidation process (in a Britton-Robinson buffer solution pH 10.0) at +0.20 V (vs. an Ag pseudoreference electrode) on an untreated screen-printed carbon electrode (SPCE) was carried out. Thus, a cyclic voltammetric based reproducible determination of acetaminophen (R.S.D., 2.2%) in the range 2.5 x 10{sup -6} M to 1 x 10{sup -3} M, was obtained. However, when SPCEs are used as amperometric detectors coupled to a flow injection analysis (FIA) system, the detection limit achieved for paracetamol was 1 x 10{sup -7} M, one order of magnitude lower than that obtained by voltammetric analysis. The repeatability of the amperometric detection with the same SPCE is 2% for 15 successive injections of 10{sup -5} M acetaminophen and do not present any memory effect. Finally, the applicability of using screen-printed carbon electrodes for the electrochemical detection of paracetamol (i.e. for quality control analysis) was demonstrated by using two commercial pharmaceutical products.

  1. Down scaled Kjeldahl digestion and flow injection conductometric system for determination of protein content in some traditional northern Thai foods.

    Science.gov (United States)

    Yanu, Pattama; Jakmunee, Jaroon

    2017-09-01

    A flow injection conductometric (FIC) system for determination of total Kjeldahl nitrogen (TKN) was developed for estimating total protein content in food. A small scale Kjeldahl digestion was performed with a short digestion time of only 20min. The digested solution was injected into the FIC system, and TKN was converted to ammonia gas in an alkaline donor stream of the system. The gas diffused through a membrane and dissolved into an acceptor stream causing an increase in conductivity as detected by a detector and recorded as a peak. Under the optimum condition, a linear calibration graph in the range of 4.00-100.00mgL -1 was obtained with LOD of 0.05mgL -1 . A good precision (0.04% RSD, n=11, 30.00mgNL -1 ) and high sample throughput of 72h -1 was achieved. The method was applied for determination of protein in some traditional northern Thai foods, revealing that they are good sources of proteins. Copyright © 2017 Elsevier Ltd. All rights reserved.

  2. MHD Modelling of Coronal Loops: Injection of High-Speed Chromospheric Flows

    Science.gov (United States)

    Petralia, A.; Reale, F.; Orlando, S.; Klimchuk, J. A.

    2014-01-01

    Context. Observations reveal a correspondence between chromospheric type II spicules and bright upward-moving fronts in the corona observed in the extreme-ultraviolet (EUV) band. However, theoretical considerations suggest that these flows are probably not the main source of heating in coronal magnetic loops. Aims. We investigate the propagation of high-speed chromospheric flows into coronal magnetic flux tubes and the possible production of emission in the EUV band. Methods. We simulated the propagation of a dense 104 K chromospheric jet upward along a coronal loop by means of a 2D cylindrical MHD model that includes gravity, radiative losses, thermal conduction, and magnetic induction. The jet propagates in a complete atmosphere including the chromosphere and a tenuous cool (approximately 0.8 MK) corona, linked through a steep transition region. In our reference model, the jet initial speed is 70 km per second, its initial density is 10(exp 11) per cubic centimeter, and the ambient uniform magnetic field is 10 G. We also explored other values of jet speed and density in 1D and different magnetic field values in 2D, as well as the jet propagation in a hotter (approximately 1.5 MK) background loop. Results. While the initial speed of the jet does not allow it to reach the loop apex, a hot shock-front develops ahead of it and travels to the other extreme of the loop. The shock front compresses the coronal plasma and heats it to about 10(exp 6) K. As a result, a bright moving front becomes visible in the 171 Angstrom channel of the SDO/AIA mission. This result generally applies to all the other explored cases, except for the propagation in the hotter loop. Conclusions. For a cool, low-density initial coronal loop, the post-shock plasma ahead of upward chromospheric flows might explain at least part of the observed correspondence between type II spicules and EUV emission excess.

  3. Evaluation of flow injection analysis for determination of cholinesterase activities in biological material.

    Science.gov (United States)

    Cabal, Jiri; Bajgar, Jiri; Kassa, Jiri

    2010-09-06

    The method for automatic continual monitoring of acetylcholinesterase (AChE) activity in biological material is described. It is based on flexible system of plastic pipes mixing samples of biological material with reagents for enzyme determination; reaction product penetrates through the semipermeable membrane and it is spectrophotometrically determined (Ellman's method). It consists of sampling (either in vitro or in vivo), adding the substrate and flowing to dialyzer; reaction product (thiocholine) is dialyzed and mixed with 5,5'-dithio-bis-2-nitrobenzoic acid (DTNB) transported to flow spectrophotometer. Flowing of all materials is realised using peristaltic pump. The method was validated: time for optimal hydratation of the cellophane membrane; type of the membrane; type of dialyzer; conditions for optimal permeation of reaction components; optimization of substrate and DTNB concentrations (linear dependence); efficacy of peristaltic pump; calibration of analytes after permeation through the membrane; excluding of the blood permeation through the membrane. Some examples of the evaluation of the effects of AChE inhibitors are described. It was demonstrated very good uniformity of peaks representing the enzyme activity (good reproducibility); time dependence of AChE inhibition caused by VX in vitro in the rat blood allowing to determine the half life of inhibition and thus, bimolecular rate constants of inhibition; reactivation of inhibited AChE by some reactivators, and continual monitoring of the activity in the whole blood in vivo in intact and VX-intoxicated rats. The method is simple and not expensive, allowing automatic determination of AChE activity in discrete or continual samples in vitro or in vivo. It will be evaluated for further research of cholinesterase inhibitors. Copyright (c) 2010 Elsevier Ireland Ltd. All rights reserved.

  4. Flow visualization and simulation of the filling process during injection molding

    DEFF Research Database (Denmark)

    Guerrier, Patrick; Tosello, Guido; Hattel, Jesper Henri

    2017-01-01

    . A high speed camera recording 500 frames per second was employed, and the mold had three thermocouples and two pressure sensors installed. The molded part is a 2. mm thick plate with a 0.5. mm thin section, which creates a characteristic V-shaped flow pattern. Two different materials were employed...... simulation results showed deviations within 10-30. ms (relative deviation in the order of 5-10%) for the ABS and slightly more for the high viscosity PC in the range of 100-500. ms (relative deviation in the order of 20-30%) on timings between different sections during filling....

  5. Spectral linewidth of autonomous and injection-locked flux-flow oscillators

    DEFF Research Database (Denmark)

    Koshelets, V. P.; Shchukin, A.; Lapytskaya, I. L.

    1995-01-01

    -flow oscillators (FFO) as low as 750 kHz was found at 280 GHz. Presently no theory exists for the linewidth of the FFO. Above a few MHz the experimental linewidth scales with the square of the dynamic resistance of the dc I-V curve as found for short Josephson junctions and oscillators based on resonant motion...... of fluxons in under-damped long Josephson tunnel junctions. Based on calculations assuming wideband thermal noise, we find that the effective temperature of the FFO appears to be much higher than its physical temperature. Different models are discussed in order to explain this discrepancy. Finally harmonic...

  6. Electrochemical flow injection analysis of hydrazine in an excess of an active pharmaceutical ingredient: achieving pharmaceutical detection limits electrochemically.

    Science.gov (United States)

    Channon, Robert B; Joseph, Maxim B; Bitziou, Eleni; Bristow, Anthony W T; Ray, Andrew D; Macpherson, Julie V

    2015-10-06

    The quantification of genotoxic impurities (GIs) such as hydrazine (HZ) is of critical importance in the pharmaceutical industry in order to uphold drug safety. HZ is a particularly intractable GI and its detection represents a significant technical challenge. Here, we present, for the first time, the use of electrochemical analysis to achieve the required detection limits by the pharmaceutical industry for the detection of HZ in the presence of a large excess of a common active pharmaceutical ingredient (API), acetaminophen (ACM) which itself is redox active, typical of many APIs. A flow injection analysis approach with electrochemical detection (FIA-EC) is utilized, in conjunction with a coplanar boron doped diamond (BDD) microband electrode, insulated in an insulating diamond platform for durability and integrated into a two piece flow cell. In order to separate the electrochemical signature for HZ such that it is not obscured by that of the ACM (present in excess), the BDD electrode is functionalized with Pt nanoparticles (NPs) to significantly shift the half wave potential for HZ oxidation to less positive potentials. Microstereolithography was used to fabricate flow cells with defined hydrodynamics which minimize dispersion of the analyte and optimize detection sensitivity. Importantly, the Pt NPs were shown to be stable under flow, and a limit of detection of 64.5 nM or 0.274 ppm for HZ with respect to the ACM, present in excess, was achieved. This represents the first electrochemical approach which surpasses the required detection limits set by the pharmaceutical industry for HZ detection in the presence of an API and paves the wave for online analysis and application to other GI and API systems.

  7. Assessment of effect of intravitreal ranibizumab injection on the ocular blood flow in patients with neovascular age-related macular degeneration

    Directory of Open Access Journals (Sweden)

    V. V. Neroev

    2014-07-01

    Full Text Available Purpose: To evaluate the effect of intravitreal ranibizumab injection on the ocular blood flow in patients with neovascular agerelatedmacular degeneration (AMD.Methods: 35 patients with wet AMD undergone intravitreal 0.5 mg ranibizumab injection. Color Doppler Imaging (CDI and dopplerographywere used to measure hemodynamic parameters including the peak systolic velocity (Vsyst, cm / s, end-diastolic velocity (V diast, cm / s, and resistance index (RI of blood flow in the central retinal artery (CRA, the short posterior ciliary arteries (PCA, and the ophthalmic artery (OA. All patients were examined before and after injection on day 1‑7 and 30 day during the 3‑month follow up period.Results: Before intravitreal injection Vsyst was decreased in short PCA (p<0.05, RI in CRA and in short PCA significantly increased in comparison with normal index in same vessels. The peak systolic velocity in OA, in CRA and in short PCA was not significantly changed. After second injection resistance index in CRA and in short PCA was normalized.Conclusion: There was not impairment of ocular blood flow in retinal and choroidal after monthly intravitreal injection of ranibizumab during the 3‑month follow up period.

  8. Assessment of effect of intravitreal ranibizumab injection on the ocular blood flow in patients with neovascular age-related macular degeneration

    Directory of Open Access Journals (Sweden)

    V. V. Neroev

    2013-01-01

    Full Text Available Purpose: To evaluate the effect of intravitreal ranibizumab injection on the ocular blood flow in patients with neovascular agerelatedmacular degeneration (AMD.Methods: 35 patients with wet AMD undergone intravitreal 0.5 mg ranibizumab injection. Color Doppler Imaging (CDI and dopplerographywere used to measure hemodynamic parameters including the peak systolic velocity (Vsyst, cm / s, end-diastolic velocity (V diast, cm / s, and resistance index (RI of blood flow in the central retinal artery (CRA, the short posterior ciliary arteries (PCA, and the ophthalmic artery (OA. All patients were examined before and after injection on day 1‑7 and 30 day during the 3‑month follow up period.Results: Before intravitreal injection Vsyst was decreased in short PCA (p<0.05, RI in CRA and in short PCA significantly increased in comparison with normal index in same vessels. The peak systolic velocity in OA, in CRA and in short PCA was not significantly changed. After second injection resistance index in CRA and in short PCA was normalized.Conclusion: There was not impairment of ocular blood flow in retinal and choroidal after monthly intravitreal injection of ranibizumab during the 3‑month follow up period.

  9. 3D simulation of polyurethane foam injection and reacting mold flow in a complex geometry

    Science.gov (United States)

    Özdemir, İ. Bedii; Akar, Fırat

    2017-11-01

    The aim of the present work is to develop a flow model which can be used to determine the paths of the polyurethane foam in the mold filling process of a refrigerator cabinet so that improvements in the distribution and the size of the venting holes can be achieved without the expensive prototyping and experiments. For this purpose, the multi-component, two-phase chemically reacting flow is described by Navier Stokes and 12 scalar transport equations. The air and the multi-component foam zones are separated by an interface, which moves only with advection since the mass diffusion of species are set zero in the air zone. The inverse density, viscosity and other diffusion coefficients are calculated by a mass fraction weighted average of the corresponding temperature-dependent values of all species. Simulations are performed in a real refrigerator geometry, are able to reveal the problematical zones where air bubbles and voids trapped in the solidified foam are expected to occur. Furthermore, the approach proves itself as a reliable design tool to use in deciding the locations of air vents and sizing the channel dimensions.

  10. Numerical Analysis of Flow Evolution in a Helium Jet Injected into Ambient Air

    Science.gov (United States)

    Satti, Rajani P.; Agrawal, Ajay K.

    2005-01-01

    A computational model to study the stability characteristics of an evolving buoyant helium gas jet in ambient air environment is presented. Numerical formulation incorporates a segregated approach to solve for the transport equations of helium mass fraction coupled with the conservation equations of mixture mass and momentum using a staggered grid method. The operating parameters correspond to the Reynolds number varying from 30 to 300 to demarcate the flow dynamics in oscillating and non-oscillating regimes. Computed velocity and concentration fields were used to analyze the flow structure in the evolving jet. For Re=300 case, results showed that an instability mode that sets in during the evolution process in Earth gravity is absent in zero gravity, signifying the importance of buoyancy. Though buoyancy initiates the instability, below a certain jet exit velocity, diffusion dominates the entrainment process to make the jet non-oscillatory as observed for the Re=30 case. Initiation of the instability was found to be dependent on the interaction of buoyancy and momentum forces along the jet shear layer.

  11. Mercury(II) determination in commercial cosmetics and local Thai traditional medicines by flow injection spectrophotometry.

    Science.gov (United States)

    Prasertboonyai, K; Liawraungrath, B; Pojanakaroon, T; Liawraungrath, S

    2016-02-01

    The proposed method was developed for the enhancement of sensitivity for Hg(II) determination using dithizone by adding SDS in the presence of ascorbic acid in sulphuric acid medium. The method was based on the reaction between Hg(II) and 1,5-diphenylthiocarbazone (dithizone), in the presence of sodium dodecyl sulphate (SDS) as an anionic surfactant (to avoid solvent extraction) and ascorbic acid in a slightly acidic medium resulting in a soluble orange coloured Hg(II)-dithizone complex which gave the maximum absorption at 490 nm. No extraction system was required in this method. Under the optimum conditions, a linear calibration graph was obtained over the concentration range of 0.05-1.50 μg mL(-1). The method was characterized by a limit of detection (LOD, defined as 3σ) and limit of quantification (LOQ, defined as 10σ) of 0.03 and 0.14 μg mL(-1), respectively. The relative standard deviations for replicate injection were 1.32 and 0.78% (n = 11) for 0.05 and 0.20 μg mL(-1) of Hg(II) standard solutions, respectively. The developed method has been satisfactorily applied for Hg(II) determination in commercial cosmetics and local Thai traditional medicines. Results obtained by the proposed method are compared favourably with those analysed by ICP-MS. Enhancement of sensitivity and rapidity for Hg(II) assay by FIA could be achieved by adding SDS in ascorbic acid. The method would be useful for routine analysis of Hg(II) in real samples. © 2015 Society of Cosmetic Scientists and the Société Française de Cosmétologie.

  12. Amperometric detection of acetaminophen by an electrochemical sensor based on cobalt oxide nanoparticles in a flow injection system

    Energy Technology Data Exchange (ETDEWEB)

    Razmi, Habib, E-mail: h.razmi@azaruniv.ed [Electrochemistry Research Laboratory, Faculty of Sciences, Azarbaijan University of Tarbiat Moallem, P.O. Box 53714-161, Tabriz (Iran, Islamic Republic of); Habibi, Esmaeil [Electrochemistry Research Laboratory, Faculty of Sciences, Azarbaijan University of Tarbiat Moallem, P.O. Box 53714-161, Tabriz (Iran, Islamic Republic of)

    2010-12-01

    This paper reports the use of a carbon ceramic electrode as a highly-porous substrate for the electrochemical formation of cobalt oxide nanoparticles. The electrocatalyst was characterized by energy dispersive X-ray (EDX) spectroscopy, scanning electron microscopy (SEM) and cyclic voltammetry techniques, and it was used in a homemade flow injection analysis (FIA) system for acetaminophen determination using 0.1 M KOH as the carrier solution. The rate constant (k{sub s}) and charge transfer coefficient ({alpha}) were calculated for the electron exchange reaction of the modified film. The kinetic parameters and the mechanism of acetaminophen electrooxidation at the electrode surface were studied by cyclic voltammetry and chronoamperometry. The effects of working potential and flow rate on the performance of the FIA system were studied. Under optimized conditions, the electrode response due to the electrocatalytic oxidation of acetaminophen at 450 mV (vs. SCE) is proportional to the concentration of acetaminophen over a 5-35 {mu}M range with an associated detection limit (S/N = 3) of 0.37 {mu}M and a sensitivity of 0.0296 {mu}A/{mu}M. The relative standard deviation (RSD) was 1.6% for eight replicate measurements. The modified electrode was used to determine the acetaminophen content in tablet samples.

  13. Detection of Total Phenol in Green and Black Teas by Flow Injection System and Unmodified Screen Printed Electrode

    Directory of Open Access Journals (Sweden)

    Ivanildo Luiz de Mattos

    2010-01-01

    Full Text Available A flow injection system using an unmodified gold screen-printed electrode was employed for total phenol determination in black and green teas. In order to avoid passivation of the electrode surface due to the redox reaction, preoxidation of the sample was realized by hexacyanoferrate(III followed by addition of an EDTA solution. The complex formed in the presence of EDTA minimizes or avoids polymerization of the oxidized phenols. The previously filtered tea sample and hexacyanoferrate(III reagent were introduced simultaneously into two-carrier streams producing two reproducible zones. At confluence point, the pre-oxidation of the phenolic compounds occurs while this zone flows through the coiled reactor and receives the EDTA solution before phenol detection. The consumption of ferricyanide was monitorized at 360 mV versus Ag/AgCl and reflected the total amount of phenolic compounds present in the sample. Results were reported as gallic acid equivalents (GAEs. The proposed system is robust, versatile, environmentally-friendly (since the reactive is used only in the presence of the sample, and allows the analysis of about 35–40 samples per hour with detection limit = 1 mg/L without the necessity for surface cleaning after each measurement. Precise results are in agreement with those obtained by the Folin-Ciocalteu method.

  14. Photoamperometric flow injection analysis of glucose based on dehydrogenase modified quantum dots-carbon nanotube nanocomposite electrode.

    Science.gov (United States)

    Ertek, Bensu; Dilgin, Yusuf

    2016-12-01

    In this work, a core-shell quantum dot (QD, ZnS-CdS) was electrodeposited onto multiwalled carbon nanotube modified glassy carbon electrode (ZnS-CdS/MWCNT/GCE) and following glucose dehydrogenase (GDH) was immobilized onto QD modified electrode. The proposed electrode (GDH/ZnS-CdS/MWCNT/GCE) was effectively used for the photoelectrochemical biosensing of glucose in flow injection analysis (FIA) system using a home-made flow cell. Results from cyclic voltammetric and FI amperometric measurements have revealed that GDH/ZnS-CdS/MWCNT/GCE is capable of signaling photoelectrocatalytic activity toward NADH when the surface of enzyme modified electrode was irradiated with a light source (250W Halogen lamp). Thus, photoelectrochemical biosensing of glucose was monitored by recording current-time curve of enzymatically produced NADH at optimized conditions. The biosensor response was found linear over the range 0.010-2.0mM glucose with detection limits of 6.0 and 4.0μM for amperometric and photoamperometric methods, respectively. The relative standard deviations (n=5) for 0.5mM glucose were 5.8% and 3.8% for photoamperometric and amperometric results, respectively. The photoelectrochemical biosensor was successfully applied to the real samples. The results with this biosensor showed good selectivity, repeatability and sensitivity for monitoring glucose in amperometric and photoamperometric FIA studies. Copyright © 2016 Elsevier B.V. All rights reserved.

  15. Flow injection chemiluninescence for detecting picogram amounts of dobesilate in human urine

    Science.gov (United States)

    Song, Zhenghua; Yue, Qiaoli; Wang, Changna

    2004-08-01

    A sensitive method for the determination of dobesilate in pharmaceutical preparations and human urine is described by using controlled-reagent-release technology. The method entailed the use of luminol and periodate, which are immobilized on anion exchange resin and react in alkaline medium, giving chemiluminescence (CL) at 425 nm. Dobesilate was detected by measuring the decrease of CL intensity, and which was observed linear over the dobesilate concentration range of 10-600 pg ml -1, and the limit of detection was 3.5 pg ml -1 (3 σ) and a relative standard deviation of less than 3.0%. At a flow rate of 2.0 ml min -1, the determination of dobesilate, including sampling and washing, could be performed in 0.5 min, giving a throughput of about 120 times per hour. The proposed method has an extremely low limit of detection down to 3.5 pg ml -1, thus it can be applied directly in the assay of human urine without any pre-treatment. It was also found that the dobesilate concentration reached its maximum after orally administrated for 3.5 h, and the excretion ratio in 24 h was 58.8% in the body of volunteers.

  16. Flow injection analysis of organic peroxide explosives using acid degradation and chemiluminescent detection of released hydrogen peroxide.

    Science.gov (United States)

    Mahbub, Parvez; Zakaria, Philip; Guijt, Rosanne; Macka, Mirek; Dicinoski, Greg; Breadmore, Michael; Nesterenko, Pavel N

    2015-10-01

    The applicability of acid degradation of organic peroxides into hydrogen peroxide in a pneumatically driven flow injection system with chemiluminescence reaction with luminol and Cu(2+) as a catalyst (FIA-CL) was investigated for the fast and sensitive detection of organic peroxide explosives (OPEs). The target OPEs included hexamethylene triperoxide diamine (HMTD), triacetone triperoxide (TATP) and methylethyl ketone peroxide (MEKP). Under optimised conditions maximum degradations of 70% and 54% for TATP and HMTD, respectively were achieved at 162 µL min(-1), and 9% degradation for MEKP at 180 µL min(-1). Flow rates were precisely controlled in this single source pneumatic pressure driven multi-channel FIA system by model experiments on mixing of easily detectable component solutions. The linear range for detection of TATP, HMTD and H2O2 was 1-200 µM (r(2)=0.98-0.99) at both flow rates, while that for MEKP was 20-200 µM (r(2)=0.97) at 180 µL min(-1). The detection limits (LODs) obtained were 0.5 µM for TATP, HMTD and H2O2 and 10 µM for MEKP. The detection times varied from 1.5 to 3 min in this FIA-CL system. Whilst the LOD for H2O2 was comparable with those reported by other investigators, the LODs and analysis times for TATP and HMTD were superior, and significantly, this is the first time the detection of MEKP has been reported by FIA-CL. Copyright © 2015 Elsevier B.V. All rights reserved.

  17. Mathematical modeling of the behavior of geothermal systems under exploitation

    Energy Technology Data Exchange (ETDEWEB)

    Bodvarsson, G.S.

    1982-01-01

    Analytical and numerical methods have been used in this investigation to model the behavior of geothermal systems under exploitation. The work is divided into three parts: (1) development of a numerical code, (2) theoretical studies of geothermal systems, and (3) field applications. A new single-phase three-dimensional simulator, capable of solving heat and mass flow problems in a saturated, heterogeneous porous or fractured medium has been developed. The simulator uses the integrated finite difference method for formulating the governing equations and an efficient sparse solver for the solution of the linearized equations. In the theoretical studies, various reservoir engineering problems have been examined. These include (a) well-test analysis, (b) exploitation strategies, (c) injection into fractured rocks, and (d) fault-charged geothermal reservoirs.

  18. Stall margin improvement of an axial flow fan with end wall injection and suction; Hekimen fukidashi suidashi ni yoru han'yo jikuryu sofuki no shissoku kaizen

    Energy Technology Data Exchange (ETDEWEB)

    Nishioka, K.; Kuroda, H.; Obata, S.; Chimura, O. [National Defense Academy, Kanagawa (Japan)

    1999-06-25

    The experimental studies are conducted to reveal the mechanism of stall margin improvement of an axial flow fan by injection or suction from the end wall. In case of injection, the largest improvement is obtained by the injection at about 0. 14 {approx} 0 .21 times axial chord length downstream from leading edge. The reason for large improvement is that stall vortex, shed intermittent separation vortex and tip leakage vortex are dissipated by this injection, and also that this blowing suppresses the separation of boundary layer. In case of suction, the largest improvement is found for the suction from the end wall near leading edge. The amplitude of periodic static pressure after stall inception becomes smaller in comparison with injection cases. These effects are increased with the increase of suction flow rate, because the discharge of the vortex occurs more easily. On the other hand, the suction from the upstream of leading edge reduces the axial velocity near rotor tip, and then it induces stall. Also we tried to visualize the tip region flow, The suppression mechanism is discussed based on the visualization. The suppression of stall is successfully photographed. (author)

  19. Thermodynamic study of β-cyclodextrin-dye inclusion complexes using gradient flow injection technique and molecular modeling.

    Science.gov (United States)

    Izadmanesh, Y; Ghasemi, Jahan B

    2016-08-05

    Gradient flow injection technique-diode array spectrophotometry was applied for β-cyclodextrin (β-CD)-dye inclusion complex studies. A single injection of a small amount of mixed β-CD-dye solution (100μl) into the carrier solution of the dye and recording the spectra gave the titration data. The mole ratio data were calculated by calibrating the dispersion pattern using a calibrator dye (rose bengal). Model-based multivariate methods were used to analyze the spectral-mole ratio data and, as a result, estimate stability constants and concentration-spectral profiles. Reliability was tested by applying this method to study the β-CD host-guest complexes with several dyes as guest molecules. Singular value decomposition (SVD) was used to select the chemical model and reduce noise. Molecular modeling provided the ability to predict the guest conformation-orientation (posing) within the cavity of β-CD and the nature of the involved interactions. Among those dyes showing observable spectral variation, the stoichiometric ratio of β-CD: dye (and log Kf) of methyl orange, fluorescein, phenol red, 4-(2-pyridylazo) resorcinol (PAR), and crystal violet were calculated to be 1:1 (4.26±0.01), 1:1 (1.53±0.08), 1:1 (3.11±0.04), 1:1 (1.06±0.12), and 2:1 (5.27±0.03), respectively. Compared with the classical method of titration, this method is simple and fast and has the advantage of needing reduced human interference. Molecular modeling facilitates a better understanding of the type of interactions and conformation of guest molecules in the β-CD cavity. The details of the proposed method are discussed in this paper. Copyright © 2016 Elsevier B.V. All rights reserved.

  20. Flow injection on-line oxidizing fluorometry coupled to dialysis sampling for the study of carbamazepine-protein binding

    Energy Technology Data Exchange (ETDEWEB)

    Zhang Zhiqi [School of Chemistry and Materials Science, Shaanxi Normal University, Xi' an 710062 (China)]. E-mail: zqzhang@snnu.edu.cn; Liang Guoxi [School of Chemistry and Materials Science, Shaanxi Normal University, Xi' an 710062 (China)

    2005-04-22

    The mechanism of binding of carbamazepine (CBZ) with bovine serum albumin (BSA) has been investigated in vitro based on a new flow injection fluorometry coupled to the technique of dialysis sampling. The CBZ and BSA were mixed in different molar ratios in 0.050 mol L{sup -1} phosphate buffer (containing 0.9% NaCl), pH 7.4, and incubated at 37 {+-} 0.5 deg. C in a water bath. The dialysis sampler was utilized to sample free CBZ from mixed solution with a relative dialytic efficiency of 7.6%. Then the CBZ in dialysis solution was injected into carrier and on-line oxidized by lead dioxide solid-phase reactor into fluorescent product with a maximum excitation wavelength of 355 nm and a maximum emission wavelength of 478 nm. The fluorescence intensity measured was linear proportional with the concentration of free CBZ in mixed solution over the range of 1 x 10{sup -5} to 2 x 10{sup -4} mol L{sup -1} with the detection limit of 6 x 10{sup -6} mol L{sup -1}. According to the fluorescence measurement results from mixed solution, the association constant (K) estimated for CBZ-BSA binding and the number of the binding site (n) with Scatchard analysis were 1.08 x 10{sup 4} L mol{sup -1} and 0.94, respectively. Stern-Volmer plots indicated the presence of dynamic component in the quenching mechanism. The acting force was suggested to be mainly hydrophobic and the distance between the acceptor and donor was 3.12 nm. The estimated binding parameters agreed well with literature values.

  1. An investigation of flow-limited field-injection electrostatic spraying (FFESS) and its applications to thin film deposition

    Science.gov (United States)

    Singh, Ravindra Pratap

    Electrostatic spraying is the process of controlled disruption of a liquid surface due to excess surface charge density. The technique has found applications in a wide range of fields from agricultural sprays to fuel injectors to colloidal thrusters for space vehicle propulsion. Over the past 20 years, the technique has been intensely studied in material processing for synthesis of ceramic and metal powders, nanoparticles and thin films. The importance of the technique lies in its simple setup, high deposition efficiency, and ambient atmosphere operation. In conventional electrostatic spraying (CESS), one uses a conducting nozzle to charge the liquid, mostly by induction charging. CESS is therefore restricted to the single jet mode of spraying which occurs at low spray currents. It lacks stability and reproducibility in the high current, multiple jet regime, which can generate much finer sprays. In flow-limited field-injection electrostatic spraying (FFESS), one uses a field-injection electrode to stably and controllably inject higher currents into the liquid, a la Fowler-Nordheim, using an otherwise insulating nozzle. This way, it is possible to stably electrospray in the multiple jet mode. In addition to producing much finer sprays, the multi-jet mode atomizes liquids at higher rates, and spreads the spray over a wider region and more uniformly than single jet sprays, thus paving way for large-area uniform thin film deposition. A simple yet comprehensive theory is formulated to describe the multi jet formation. The theory, which is based on the energy minimization principle, takes into account, for the first time, the interactions between charged jets which leads to saturation in the number of jets at high spray currents. The possibility of using an array of nozzles to obtain uniform large-area high-throughput thin film deposition is also investigated. A large number of FFESS nozzles with alternating positive and negative polarities arranged in a periodic 2

  2. Selective Flow Injection Analysis of Ultra-trace Amounts of Cr(VI), Preconcentration of It by Solvent Extraction, and Determination by Electrothermal Atomic Absorption Spectrometry (ETAAS)

    DEFF Research Database (Denmark)

    Nielsen, Steffen; Sturup, Stefan; Spliid, Henrik

    1999-01-01

    A rapid, robust, sensitive and selective time-based flow injection (FI) on-line solvent extraction system interfaced with electrothermal atomic absorption spectrometry (ETAAS) is described for analyzing ultra-trace amounts of Cr(VI). The sample is initially mixed on-line with isobutyl methyl ketone...

  3. DIFFERENTIATION OFAURANTII FRUCTUS IMMATURUSANDFRUCTUS PONICIRI TRIFOLIATAE IMMATURUSBY FLOW-INJECTION WITH ULTRAVIOLET SPECTROSCOPIC DETECTION AND PROTON NUCLEAR MAGNETIC RESONANCE USING PARTIAL LEAST-SQUARES DISCRIMINANT ANALYSIS.

    Science.gov (United States)

    Zhang, Mengliang; Zhao, Yang; Harrington, Peter de B; Chen, Pei

    2016-03-01

    Two simple fingerprinting methods, flow-injection coupled to ultraviolet spectroscopy and proton nuclear magnetic resonance, were used for discriminating between Aurantii fructus immaturus and Fructus poniciri trifoliatae immaturus . Both methods were combined with partial least-squares discriminant analysis. In the flow-injection method, four data representations were evaluated: total ultraviolet absorbance chromatograms, averaged ultraviolet spectra, absorbance at 193, 205, 225, and 283 nm, and absorbance at 225 and 283 nm. Prediction rates of 100% were achieved for all data representations by partial least-squares discriminant analysis using leave-one-sample-out cross-validation. The prediction rate for the proton nuclear magnetic resonance data by partial least-squares discriminant analysis with leave-one-sample-out cross-validation was also 100%. A new validation set of data was collected by flow-injection with ultraviolet spectroscopic detection two weeks later and predicted by partial least-squares discriminant analysis models constructed by the initial data representations with no parameter changes. The classification rates were 95% with the total ultraviolet absorbance chromatograms datasets and 100% with the other three datasets. Flow-injection with ultraviolet detection and proton nuclear magnetic resonance are simple, high throughput, and low-cost methods for discrimination studies.

  4. Investigations into the Role of Modifiers for Entrapment of Hydrides in Flow Injection Hydride Generation Electrothermal Atomic Absorption Spectrometry as Exemplified for the Determination of Germanium

    DEFF Research Database (Denmark)

    Hilligsøe, Bo; Andersen, Jens Enevold Thaulov; Hansen, Elo Harald

    1997-01-01

    Pd-conditioned graphite tubes, placed in the furnace of an atomic absorption spectrometry instrument, are used for entrapment of germane as generated in an associated flow injection system. Two different approaches are tested with the ultimate aim to allow multiple determinations, that is, introd...

  5. Raman spectroscopic analysis of cyanogenic glucosides in plants: development of a Flow Injection Surface-Enhanced Raman Scatter (FI-SERS) method for determination of cyanide

    DEFF Research Database (Denmark)

    Thygesen, Lisbeth Garbrecht; Jørgensen, Kirsten; Møller, Birger Lindberg

    2004-01-01

    -dried sorghum leaf was also obtained using this instrument. Surface-enhanced Raman Spectroscopy (SERS) was demonstrated to be a more sensitive method that enabled determination of the cyanogenic potential of plant tissue. The SERS method was optimized by flow injection (FI) using a colloidal gold dispersion...... as effluent. Potential problems and pitfalls of the method are discussed....

  6. Mercury speciation in sea food by flow injection cold vapor atomic absorption spectrometry using selective solid phase extraction.

    Science.gov (United States)

    Vereda Alonso, E; Siles Cordero, M T; García de Torres, A; Cañada Rudner, P; Cano Pavón, J M

    2008-10-19

    An on-line inorganic and organomercury species separation, preconcentration and determination system consisting of cold vapor atomic absorption spectrometry (CV-AAS or CV-ETAAS) coupled to a flow injection (FI) method was studied. The inorganic mercury species was retained on a column (i.d., 3 mm; length 3 cm) packed to a height of 0.7 cm with a chelating resin aminopropyl-controlled pore glass (550 A) functionalized with [1,5-bis (2 pyridyl)-3-sulphophenyl methylene thiocarbonohydrazyde] placed in the injection valve of a simple flow manifold. Methylmercury is not directly determined. Previous oxidation of the organomercurial species permitted the determination of total mercury. The separation of mercury species was obtained by the selective retention of inorganic mercury on the chelating resin. The difference between total and inorganic mercury determined the organomercury content in the sample. The inorganic mercury was removed on-line from the microcolumn with 6% (m/v) thiourea. The mercury cold vapor generation was performed on-line with 0.2% (m/v) sodium tethrahydroborate and 0.05% (m/v) sodium hydroxide as reducing solution. The determination was performed using CV-AAS and CV-ETAAS, both approaches have been used and compared for the speciation of mercury in sea food. A detection limit of 10 and 6 ng l(-1) was achieved for CV-AAS and CV-ETAAS, respectively. The precision for 10 replicate determinations at the 1 microg l(-1) Hg level was 3.5% relative standard deviation (R.S.D.), calculated from the peak heights obtained. Both approaches were validated with the use of two certified reference materials and by spiking experiments. By analyzing the two biological certified materials, it was evident that the difference between the total mercury and inorganic mercury corresponds to methylmercury. The concentrations obtained by both techniques were in agreement with the certified values or with differences of the certified values for total Hg(2+) and CH(3)Hg

  7. Preserving drinking water quality in geotechnical operations: predicting the feedback between fluid injection, fluid flow, and contamination

    Science.gov (United States)

    Schilling, Frank R.

    2014-05-01

    Not only in densely populated areas the preservation of drinking water quality is of vital interest. On the other side, our modern economies request for a sustained energy supply and a secure storage of waste materials. As energy sources with a high security of supply, oil, natural gas, and geothermal energy cover ca. 60% of Europe's energy demand; together with coal more than 75% (IEA 2011). Besides geothermal energy, all of the resources have a high greenhouse gas footprint. All these production activities are related to fluid injection and/or fluid production. The same holds true for gas storage operations in porous reservoirs, to store natural gases, oil, or greenhouse gases. Different concerns are discussed in the public and geoscientific community to influence the drinking water quality: - wastewater discharges from field exploration, drilling, production, well treatment and completion - wastewater sequestration - gas storage - tight gas and tight oil production (including hydraulic fracturing) - Shale gas production (including hydraulic fracturing) - mine drainage This overview contribution focusses on strategies to systematically reduce the risk of water pollution in geotechnical operations of deep reservoirs. The principals will be exemplarily revealed for different geotechnical operations. - How to control hydraulic fracturing operations to reduce the risk of enhanced seismic activity and avoiding the connection of originally separated aquifers. The presented approach to quantitatively predict the impact of stimulation activities is based on petrophysical models taking the feedback of geomechanical processes and fluid flow in porous media, fissures and faults into account. The specific flow patterns in various rock types lead to distinguished differences in operational risk. - How can a proper planning of geotechnical operations reduce the involved risks. A systematic risk reduction strategy will be discussed. On selected samples the role of exploration

  8. Novel miniaturized sensors for potentiometric batch and flow-injection analysis (FIA) of perchlorate in fireworks and propellants.

    Science.gov (United States)

    Almeer, Saeed H M A; Zogby, Ibrahim A; Hassan, Saad S M

    2014-11-01

    Three planar miniaturized perchlorate membrane sensors (3×5 mm(2)) are prepared using a flexible Kaptan substrate coated with nitron-perchlorate (NT-ClO4) [sensor 1], methylene blue-perchlorate (MB-ClO4) [sensor II] and indium-porphyrin (In-Por) [sensor III] as electroactive materials in PVC membranes plasticized with 2-NPPE. Sensors I, II and III display near-Nernstian response for 1.0×10(-5)-1.0×10(-2), 3.1×10(-5)-1.0×10(-2) and 3.1×10(-6)-1.0×10(-2) mol L(-1) ClO4(-) with lower detection limits of 6.1×10(-6), 6.9×10(-6) and 1.2×10(-6) mol L(-1), and anionic calibration slopes of 50.9±0.4, 48.4±0.4 and 57.7±0.3 mV decade(-1), respectively. Methods for determining perchlorate using these sensors offer many attractive advantages including simplicity, flexibility, cost effectiveness, wide linear dynamic response range (0.1-1000 ppm), low detection limit (<1.2×10(-6) mol L(-1)≡0.1 ppm), small sample test volume (100 μL), safety, short response time (<20 s), long life span (~8 weeks), and extended wide working pH range (4.5-8.0). The sensors show high selectivity in the presence of some inorganic ions (e.g., PO4(3-), SO4(2-), S2O3(2-), NO2(-), NO3(-), N3(-), CN(-), Cl(-), Br(-), I(-)) and automation feasibility. Indium-porphyrin based membrane sensor (sensor III) is used as a detector in a wall-jet flow injection set-up to enable accurate flow injection analysis (FIA) of perchlorate in some fireworks without interferences from the associated reducing agents (sulfur and charcoal), binders (dextrin, lactose), coloring agents (calcium, strontium, copper, iron, sodium), color brighten (linseed oil) and regulators (aluminum flakes) which are commonly used in the formulations. The sensor is also used for perchlorate assessment in some propellant powders. The results fairly agree with data obtained by ion-chromatography. Copyright © 2014 Elsevier B.V. All rights reserved.

  9. Ionophore-Based Potentiometric Sensors for the Flow-Injection Determination of Promethazine Hydrochloride in Pharmaceutical Formulations and Human Urine

    Directory of Open Access Journals (Sweden)

    Suad Mustafa Al-Araji

    2011-01-01

    Full Text Available Plasticised poly(vinyl chloride-based membranes containing the ionophores (α-, β- and γ-cyclodextrins (CD, dibenzo-18-crown-6 (DB18C6 and dibenzo-30-crown-10 (DB30C10 were evaluated for their potentiometric response towards promethazine (PM in a flow injection analysis (FIA set-up. Good responses were obtained when β- and γ-CDs, and DB30C10 were used. The performance characteristics were further improved when tetrakis(4-chlorophenyl borate (KTPB was added to the membrane. The sensor based on β-CD, bis(2-ethylhexyl adipate (BEHA and KTPB exhibited the best performance among the eighteen sensor compositions that were tested. The response was linear from 1 x 10−5 to 1 x 10−2 M, slope was 61.3 mV decade−1, the pH independent region ranged from 4.5 to 7.0, a limit of detection of 5.3 x 10−6 M was possible and a lifetime of more than a month was observed when used in the FIA system. Other plasticisers such as dioctyl phenylphosphonate and tributyl phosphate do not show significant improvements in the quality of the sensors. The promising sensors were further tested for the effects of foreign ions (Li+, Na+, K+, Mg2+, Ca2+, Co2+, Cu2+, Cr3+, Fe3+, glucose, fructose. FIA conditions (e.g., effects of flow rate, injection volume, pH of the carrier stream were also studied when the best sensor was used (based on β-CD. The sensor was applied to the determination of PM in four pharmaceutical preparations and human urine that were spiked with different levels of PM. Good agreement between the sensor and the manufacturer’s claimed values (for pharmaceutical preparations was obtained, while mean recoveries of 98.6% were obtained for spiked urine samples. The molecular recognition features of the sensors as revealed by molecular modelling were rationalised by the nature of the interactions and complexation energies between the host and guest molecules.

  10. Ionophore-Based Potentiometric Sensors for the Flow-Injection Determination of Promethazine Hydrochloride in Pharmaceutical Formulations and Human Urine

    Science.gov (United States)

    Hassan, Ahmed Khudhair; Saad, Bahruddin; Ghani, Sulaiman Ab; Adnan, Rohana; Rahim, Afidah Abdul; Ahmad, Norariza; Mokhtar, Marina; Ameen, Suham Tawfiq; Al-Araji, Suad Mustafa

    2011-01-01

    Plasticised poly(vinyl chloride)-based membranes containing the ionophores (α-, β- and γ-cyclodextrins (CD), dibenzo-18-crown-6 (DB18C6) and dibenzo-30-crown-10 (DB30C10) were evaluated for their potentiometric response towards promethazine (PM) in a flow injection analysis (FIA) set-up. Good responses were obtained when β- and γ-CDs, and DB30C10 were used. The performance characteristics were further improved when tetrakis(4-chlorophenyl) borate (KTPB) was added to the membrane. The sensor based on β-CD, bis(2-ethylhexyl) adipate (BEHA) and KTPB exhibited the best performance among the eighteen sensor compositions that were tested. The response was linear from 1 × 10−5 to 1 × 10−2 M, slope was 61.3 mV decade−1, the pH independent region ranged from 4.5 to 7.0, a limit of detection of 5.3 × 10−6 M was possible and a lifetime of more than a month was observed when used in the FIA system. Other plasticisers such as dioctyl phenylphosphonate and tributyl phosphate do not show significant improvements in the quality of the sensors. The promising sensors were further tested for the effects of foreign ions (Li+, Na+, K+, Mg2+, Ca2+, Co2+, Cu2+, Cr3+, Fe3+, glucose, fructose). FIA conditions (e.g., effects of flow rate, injection volume, pH of the carrier stream) were also studied when the best sensor was used (based on β-CD). The sensor was applied to the determination of PM in four pharmaceutical preparations and human urine that were spiked with different levels of PM. Good agreement between the sensor and the manufacturer’s claimed values (for pharmaceutical preparations) was obtained, while mean recoveries of 98.6% were obtained for spiked urine samples. The molecular recognition features of the sensors as revealed by molecular modelling were rationalised by the nature of the interactions and complexation energies between the host and guest molecules. PMID:22346617

  11. Exploitation of subsea gas hydrate reservoirs

    Science.gov (United States)

    Janicki, Georg; Schlüter, Stefan; Hennig, Torsten; Deerberg, Görge

    2016-04-01

    Natural gas hydrates are considered to be a potential energy resource in the future. They occur in permafrost areas as well as in subsea sediments and are stable at high pressure and low temperature conditions. According to estimations the amount of carbon bonded in natural gas hydrates worldwide is two times larger than in all known conventional fossil fuels. Besides technical challenges that have to be overcome climate and safety issues have to be considered before a commercial exploitation of such unconventional reservoirs. The potential of producing natural gas from subsea gas hydrate deposits by various means (e.g. depressurization and/or injection of carbon dioxide) is numerically studied in the frame of the German research project »SUGAR«. The basic mechanisms of gas hydrate formation/dissociation and heat and mass transport in porous media are considered and implemented into a numerical model. The physics of the process leads to strong non-linear couplings between hydraulic fluid flow, hydrate dissociation and formation, hydraulic properties of the sediment, partial pressures and seawater solution of components and the thermal budget of the system described by the heat equation. This paper is intended to provide an overview of the recent development regarding the production of natural gas from subsea gas hydrate reservoirs. It aims at giving a broad insight into natural gas hydrates and covering relevant aspects of the exploitation process. It is focused on the thermodynamic principles and technological approaches for the exploitation. The effects occurring during natural gas production within hydrate filled sediment layers are identified and discussed by means of numerical simulation results. The behaviour of relevant process parameters such as pressure, temperature and phase saturations is described and compared for different strategies. The simulations are complemented by calculations for different safety relevant problems.

  12. Flow-injection determination of total organic fluorine with off-line defluorination reaction on a solid sorbent bed.

    Science.gov (United States)

    Musijowski, Jacek; Trojanowicz, Marek; Szostek, Bogdan; da Costa Lima, José Luis Fontes; Lapa, Rui; Yamashita, Hiroki; Takayanagi, Toshio; Motomizu, Shoji

    2007-09-26

    Considering recent reports on widespread occurrence and concerns about perfluoroalkyl substances (PFAS) in environmental and biological systems, analysis of these compounds have gained much attention in recent years. Majority of analyte-specific methods are based on a LC/MS/MS or a GC/MS detection, however many environmental or biological studies would benefit from a total organic fluorine (TOF) determination. Presented work was aimed at developing a method for TOF determination. TOF is determined as an amount of inorganic fluoride obtained after defluorination reaction conducted off-line using sodium biphenyl reagent directly on the sorbent without elution of retained analytes. Recovered fluoride was analyzed using flow-injection system with either fluorimetric or potentiometric detection. The TOF method was tested using perfluorocarboxylic acids (PFCA), including perfluorooctanoic acid (PFOA), as model compounds. Considering low concentrations of PFAS in natural samples, solid-phase extraction as a preconcentration procedure was evaluated. Several carbon-based sorbents were tested, namely multi-wall carbon nanotubes, carbon nanofibres and activated carbon. Good sorption of all analytes was achieved and defluorination reaction was possible to carry out directly on a sorbent bed. Recoveries obtained for PFCAs, adsorbed on an activated carbon sorbent, and measured as TOF, were 99.5+/-1.7, 110+/-9.4, 95+/-26, 120+/-32, 110+/-12 for C4, C6, C8, C10 and C12-PFCA, respectively. Two flow systems that would enable the defluorination reaction and fluoride determination in a single system were designed and tested.

  13. Spectrophotometric flow-injection determination of sulphite in white wines involving gas diffusion through a concentric tubular membrane

    Directory of Open Access Journals (Sweden)

    Melo Denise

    2003-01-01

    Full Text Available A flow-injection system is proposed for the spectrophotometric determination of sulphite in white wines. The method involves analyte conversion to SO2, gas diffusion through a Teflon® semi-permeable membrane, collection into an alkaline stream (pH 8, reaction with Malachite green (MG and monitoring at 620 nm. With a concentric tubular membrane, the system design was simplified. Influence of reagent concentrations, pH of donor and acceptor streams, temperature, timing, surfactant addition and presence of potential interfering species of the wine matrix were investigated. A pronounced (ca. 100% enhancement in sensitivity was noted by adding cetylpyridinium chloride (CPC. The proposed system is robust and baseline drift is not observed during 4 h operating periods. Only 400 muL of sample and 0.32 mg MG are required per determination. The system handles 30 samples per hour, yielding precise results (r.s.d. < 0.015 for 1.0 - 20.0 mg L-1 SO2 in agreement with those obtained by an alternative procedure.

  14. Flow Injection Analysis with Electrochemical Detection for Rapid Identification of Platinum-Based Cytostatics and Platinum Chlorides in Water

    Directory of Open Access Journals (Sweden)

    Marketa Kominkova

    2014-02-01

    Full Text Available Platinum-based cytostatics, such as cisplatin, carboplatin or oxaliplatin are widely used agents in the treatment of various types of tumors. Large amounts of these drugs are excreted through the urine of patients into wastewaters in unmetabolised forms. This phenomenon leads to increased amounts of platinum ions in the water environment. The impacts of these pollutants on the water ecosystem are not sufficiently investigated as well as their content in water sources. In order to facilitate the detection of various types of platinum, we have developed a new, rapid, screening flow injection analysis method with electrochemical detection (FIA-ED. Our method, based on monitoring of the changes in electrochemical behavior of analytes, maintained by various pH buffers (Britton-Robinson and phosphate buffer and potential changes (1,000, 1,100 and 1,200 mV offers rapid and cheap selective determination of platinum-based cytostatics and platinum chlorides, which can also be present as contaminants in water environments.

  15. New conventional coated-wire ion-selective electrodes for flow-injection potentiometric determination of chlordiazepoxide.

    Science.gov (United States)

    Issa, Y M; Abdel-Ghani, N T; Shoukry, A F; Ahmed, Howayda M

    2005-09-01

    New chlordiazepoxide hydrochloride (Ch-Cl) ion-selective electrodes (conventional type) based on ion associates, chlordiazepoxidium-phosphomolybdate (I) and chlordiazepoxidium-phosphotungstate (II), were prepared. The electrodes exhibited mean slopes of calibration graphs of 59.4 mV and 60.8 mV per decade of (Ch-Cl) concentration at 25 degrees C for electrodes (I) and (II), respectively. Both electrodes could be used within the concentration range 3.16 x 10(-6)-1 x 10(-2) M (Ch-Cl) within the pH range 2.0-4.5. The standard electrode potentials were determined at different temperatures and used to calculate the isothermal coefficients of the electrodes, which were 0.00139 and 0.00093 V degrees C(-1) for electrodes (I) and (II), respectively. The electrodes showed a very good selectivity for Ch-Cl with respect to the number of inorganic cations, amino acids and sugars. The electrodes were applied to the potentiometric determination of the chlordiazepoxide ion and its pharmaceutical preparation under batch and flow injection conditions. Also, chlordiazepoxide was determined by conductimetric titrations. Graphite, copper and silver coated wires were prepared and characterized as sensors for the drug under investigation.

  16. The characterisation of shellac resin by flow injection and liquid chromatography coupled with electrospray ionisation and mass spectrometry.

    Science.gov (United States)

    Tamburini, Diego; Dyer, Joanne; Bonaduce, Ilaria

    2017-11-01

    A strategy based on electrospray ionisation (ESI) in negative mode coupled with quadrupole-time of flight (Q-ToF) detection techniques was adopted to characterise some samples of shellac resin. Flow injection analysis (FIA) was used to investigate the distribution of the components of the resin. Eight groups of compounds with increasing masses were detected and assigned to free acids, esters and polyesters with up to eight units. High pressure liquid chromatography (HPLC) enabled the compounds to be chromatographically separated. Accurate molecular masses and tandem mass (MS/MS) spectra interpretation were used to characterise the different compounds, assigning and/or suggesting molecular structures. In some cases, highly detailed information about the ester linkages was provided by the MS/MS spectra, enabling the different isomers to be distinguished. Oxidation products were also identified in the samples and differences were observed in terms of hydrolysis and oxidation. In addition to providing the first characterisation of shellac by HPLC-ESI-Q-ToF and an atlas of MS/MS spectra of shellac components, this work demonstrates the suitability of the proposed strategy for characterising the resin, and provides the identification of previously unknown degradation products and minor components. This represents a significant step forward in the chemical knowledge of this material.

  17. Flow injection analysis-Rayleigh light scattering detection for online determination of protein in human serum sample.

    Science.gov (United States)

    Li, Ying; Dong, Lijun; Wang, Weiping; Hu, Zhide; Chen, Xingguo

    2006-07-01

    A flow injection analysis (FIA) system combined with Rayleigh light scattering (RLS) detection is developed for the sensitive and rapid determination of protein concentration in human serum sample. This method is based on the weak intensity of RLS of Eriochrome Black T (EBT, 2-hydroxy-1-(1-hydroxy-2-naphthylazo)-6-nitronaphthalene-4-sulfonic acid sodium salt), which can be enhanced by the addition of protein in weakly acidic solution. The effects of pH and interfering species on the determination of protein were examined. Calibrations for protein, based on RLS intensity, were linear in the concentration ranges of 7-36 microg/ml for human serum album (HSA) and 8-44 microg/ml for bovine serum album (BSA). The detection limits of the method were found to be 0.882 and 2.507 microg/ml for HSA and BSA, respectively. A relative standard deviation of 0.76% (n=5) was obtained with 20 microg/ml HSA standard solution. The FIA-RLS method was more stable than the general RLS method, and the average RSD value of FIA-RLS was less than that of the general RLS. The sample rate was determined to be 90 samples per hour.

  18. A novel flow injection spectrophotometric method using plant extracts as green reagent for the determination of doxycycline

    Science.gov (United States)

    Palamy, Sysay; Ruengsitagoon, Wirat

    2017-01-01

    A novel flow injection spectrophotometric method was developed for the determination of doxycycline in pharmaceutical preparations using iron(III) contained in extracts from plants. The assay was based on the complex formed between doxycycline and iron(III) characterized by an absorption maximum at 435 nm. The calibration graphs obtained over the doxycycline concentration range 5-250 μg mL- 1 gave correlation coefficients of 0.9979, 0.9987 and 0.9987 with the three green reagents prepared from Senna alata (L.) Roxb. (S. alata), Polygonum hydropiper L. (P. hydropiper) or Diplazium esculentum (Retz.) Sw. (D. esculentum), respectively. The relative standard deviations of the repeatability was < 2.00%. The percentage recoveries were in the range of 98.27-101.03%. Doxycycline contents obtained by this new method and by the reference methods reported in literature were in agreement at 95% confidence level with the paired t-test. The sample throughput was 36 h- 1 for each green reagent.

  19. Flow Injection Photosensitized Chemiluminescence of Luminol with Cu(II-Rose Bengal: Mechanistic Approach and Vitamin A and C Determination

    Directory of Open Access Journals (Sweden)

    Muhammad Asgher

    2014-01-01

    Full Text Available Rose Bengal photosensitized flow injection chemiluminescence method is reported using luminol-Cu(II for the determination of vitamins A and C in pharmaceutical formulations. The reaction is based on the enhancement effect of analyte in the production of anion radicals of Rose Bengal (RB•− which rapidly interact with dissolved oxygen and generate superoxide anions radicals (O2•− and hydrogen peroxide (H2O2. Highly reactive hydroxyl radicals (•OH were produced via dismutation of H2O2 by catalyst (Cu2+. The generated superoxide anions radicals and hydroxyl radicals thus oxidize luminol in alkaline medium to generate strong chemiluminescence. The limit of detection (3s of the blank, n=6 of vitamins A and C and RB was found to be 0.008, 0.005, and 0.05 μg mL−1, respectively. The sample throughput of 70 h−1 for vitamins A and C and 30 h−1 for RB was found. Calibration curve was linear in the range of 0.05–15, 0.01–20, and 0.1–50 μg mL−1 for vitamins A and C and RB, respectively, with relative standard deviations (RSDs; n=3 in the range 1.6–3.6%. The method was successfully applied to pharmaceutical formulations and the results obtained were in good agreement with the labeled values.

  20. Carbon paste electrode modified with silver thimerosal for the potentiometric flow injection analysis of silver(I)

    Energy Technology Data Exchange (ETDEWEB)

    Ibrahim, Hosny [Chemistry Department, Faculty of Science, Cairo University, Cairo (Egypt)]. E-mail: dr_hosny@yahoo.com

    2005-07-27

    The utility of carbon paste electrode modified with silver ethylmercurythiosalicylate (silver thimerosal) in both static mode and flow injection analysis (FIA) is demonstrated. The electrode was fully characterized in terms of composition, response time, thermal stability, usable pH and ionic strength ranges. It has been shown that diisononyl phthalate (DINP) acts as more suitable solvent mediator for preparation of the electrode, which exhibits linear response range to Ag(I) extending from 5.0 x 10{sup -7} to 1.0 x 10{sup -3} M with detection limit of 2.5 x 10{sup -7} M and Nernstian slope of 59.3 {+-} 1.0 mV/decade. The proposed chemically modified carbon paste electrode shows a very good selectivity for Ag(I) over a wide variety of metal ions and successfully used for the determination of the silver content of silver sulphadiazine (burning cream) and developed radiological films. The electrode was also used as an indicator electrode in the potentiometric titration of thiopental and thimerosal with AgNO{sub 3}.

  1. WETTABILITY ALTERATION OF POROUS MEDIA TO GAS-WETTING FOR IMPROVING PRODUCTIVITY AND INJECTIVITY IN GAS-LIQUID FLOWS

    Energy Technology Data Exchange (ETDEWEB)

    Abbas Firoozabadi

    2003-12-01

    Wettability alteration to intermediate gas-wetting in porous media by treatment with FC-759, a fluoropolymer polymer, has been studied experimentally. Berea sandstone was used as the main rock sample in our work and its wettability before and after chemical treatment was studied at various temperatures from 25 to 93 C. We also studied recovery performance for both gas/oil and oil/water systems for Berea sandstone before and after wettability alteration by chemical treatment. Our experimental study shows that chemical treatment with FC-759 can result in: (1) wettability alteration from strong liquid-wetting to stable intermediate gas-wetting at room temperature and at elevated temperatures; (2) neutral wetting for gas, oil, and water phases in two-phase flow; (3) significant increase in oil mobility for gas/oil system; and (4) improved recovery behavior for both gas/oil and oil/water systems. This work reveals a potential for field application for improved gas-well deliverability and well injectivity by altering the rock wettability around wellbore in gas condensate reservoirs from strong liquid-wetting to intermediate gas-wetting.

  2. Simultaneous determination of three antioxidants in foods and cosmetics by flow injection coupled to an ultra-short monolithic column.

    Science.gov (United States)

    García-Jiménez, J F; Valencia, M C; Capitán-Vallvey, L F

    2009-07-01

    The combination of an ultra-short C18 monolithic column (5 mm long) with flow injection analysis results in a versatile and efficient system that has been used for the determination of three antioxidants [propylgallate (PG), butylhydroxyanisole (BA), and butylhydroxytoluene (BT)]. Due to the wide variety of polarities of the analytes, two different carriers (carrier A: methanol-water 42% and carrier B: methanol-water 70%) were able to separate the analytes in only 85 s. The applicable concentration range, the detection, and the relative standard deviation (n=10) were: for PG, from 2.77 to 300 microg/mL, 0.84 microg/mL, 2.84%; for BA, between 1.51 and 300 microg/mL, 0.46 microg/mL, and 2.70%; and for BT, between 1.65 and 100 microg/mL, 0.55 microg/mL, and 2.22%, respectively. The method was applied and validated satisfactorily for the determination of PG, BA, and BT in food and cosmetic samples.

  3. Flow-Injection Solid Phase Partial Least-Squares Spectrophotometric Simultaneous Determination of Iron, Nickel and Zinc

    Directory of Open Access Journals (Sweden)

    Teixeira Leonardo S. G.

    2002-01-01

    Full Text Available A PLS-2 multivariate calibration method has been developed for the simultaneous determination of iron, nickel and zinc in ternary mixtures by solid phase spectrophotometry associated with flow injection analysis. Fe(II, Ni(II and Zn(II form color complexes with 1-(2-thiazolylazo-2-naphthol (TAN, immobilized on a C18 bonded silica support, at pH 6.4. The proposed procedure is based on the different reaction/retention ratios of the studied ions on the solid support. Bilinear spectrophotometric data of the analytes, fixed in the solid support, were recorded in the 400-800 nm wavelength range as a function of time and a partial least squares (PLS-2 algorithm was used to predict results of synthetic samples. The calibration set employed was integrated by 8 ternary mixture standards and a blank solution. Mixtures containing 0.040 to 0.20 mg L-1, of each species, were successfully resolved, using 3 factors for each analyte and a restricted number of absorbance data obtained in the wavelength range from 560 to 650 nm.

  4. Flow injection determination of Se in dietary supplements using TiO2 mediated ultraviolet-photochemical volatile species generation

    Science.gov (United States)

    Nováková, E.; Linhart, O.; Červený, V.; Rychlovský, P.; Hraníček, J.

    2017-08-01

    This paper proposes a method for determination of selenium content in samples of dietary supplements using TiO2 mediated UV-photochemical vapor generation with quartz furnace atomic spectrometric detection. The flow-injection method was optimized for determination of selenium in the form of selenite or selenate ions. The limits of detection of the proposed method are 0.89 ng mL- 1 and 0.68 ng mL- 1 for selenite and selenate, respectively. Extraction in neutral medium was used for the leaching of selenate and NaOH solution was used for the leaching of selenite. The methods accuracy was verified against the declared amounts of Se in five different samples of over-the-counter dietary supplements and on NIST SRM 3280. The method was also compared to results achieved with determination by electrothermal atomization atomic absorption spectrometry following microwave decomposition. The recovery of selenium during sample preparation was tested by spiking the tablets prior to extraction and estimated to be approximately 100%. An interference study has been carried out to estimate the effect of concomitant elements on the methods accuracy.

  5. Titanium determination by multisyringe flow injection analysis system and a liquid waveguide capillary cell in solid and liquid environmental samples.

    Science.gov (United States)

    Sánchez-Quiles, David; Tovar-Sánchez, Antonio; Horstkotte, Burkhard

    2013-11-15

    A multisyringe flow injection analysis system using a liquid waveguide capillary cell (MSFIA-LWCC) has been used for the spectrophotometric determination of titanium (Ti) in marine environmental samples. Samples were previous digested using potassium peroxodisulfate (K2S2O8). The method showed to be linear over a range up to 1 μM with a detection limit of 9.2 nM. The analysis consumes little reagent (250 μL) and sample (600 μL). It had an adequate accuracy with high repeatability (RSD of 1.8%) for all marine samples. The proposed method was used to evaluate the concentration of Ti in natural samples collected in the coastal area of the Majorca Island (Western Mediterranean Sea). We report average concentrations of Ti in coastal surface microlayer of 510.7 ± 267.2 nM, in surface sediments of 2.72 ± 1.84 μmol/g, and in rhizomes and leaves of Posidonia oceanica of 310 ± 295 nmol/g and 157 ± 132 nmol/g, respectively. Copyright © 2013 Elsevier Ltd. All rights reserved.

  6. The Ethics of Exploitation

    Directory of Open Access Journals (Sweden)

    Paul McLaughlin

    2008-11-01

    Full Text Available Philosophical inquiry into exploitation has two major deficiencies to date: it assumes that exploitation is wrong by definition; and it pays too much attention to the Marxian account of exploitation. Two senses of exploitation should be distinguished: the ‘moral’ or pejorative sense and the ‘non-moral’ or ‘non-prejudicial’ sense. By demonstrating the conceptual inadequacy of exploitation as defined in the first sense, and by defining exploitation adequately in the latter sense, we seek to demonstrate the moral complexity of exploitation. We contend, moreover, that moral evaluation of exploitation is only possible once we abandon a strictly Marxian framework and attempt, in the long run, to develop an integral ethic along Godwinian lines.

  7. Trophallaxis in the honeybee Apis mellifera (L.): the interaction between flow of solution and sucrose concentration of the exploited food sources.

    Science.gov (United States)

    Wainselboim; Farina

    2000-06-01

    Forager bees arriving at the hive after visiting a nectar source, unload the collected liquid food to recipient hivemates through mouth-to-mouth contact (trophallaxis). We analysed whether the main characteristics that define nectar in energetic terms, that is, rate of production (flow of solution), sucrose concentration and rate of sucrose production (sucrose flow) influence trophallactic behaviour. Individual bees trained to feed at a regulated-flow feeder offering sucrose solution were captured once the foraging visit was complete and placed in an acrylic arena with a recipient bee that had not been fed. The rate at which liquid was transferred during the subsequent trophallactic contact (transfer rate) was analysed as a function of the different solution flows and sucrose concentrations offered at the feeder. A relationship was found between transfer rate during trophallaxis and the flow of solution previously presented at the feeder. This relationship was independent of sucrose concentration when above a certain threshold value (ca. 22% weight on weight). We also analysed whether the rate of sucrose deliverance of the food source (sucrose flow) influenced the rate at which the solution was transferred. No clear relationship was found between the rate of sucrose deliverance during trophallactic events (sucrose transfer rate) and the sucrose flow presented at the feeder. The possibility that trophallaxis could be a communication channel through which quantitative information on food source profitability is transmitted among hivemates is discussed. Copyright 2000 The Association for the Study of Animal Behaviour.

  8. Numerical investigation on the effect of injection pressure on the internal flow characteristics for diethyl ether, dimethyl ether and diesel fuel injectors using CFD

    Directory of Open Access Journals (Sweden)

    Vijayakumar Thulasi

    2011-01-01

    Full Text Available The spray characteristics of the diesel fuel are greatly affected by the cavitation formed inside the injector due to the high pressure differential across the nozzle. Many researchers across the globe are exploring the potential of using diethyl ether and dimethyl ether as an alternate for diesel fuel to meet the strict emission norms. Due to the variation in the fuel properties the internal flow characteristics in injectors for ether fuels are expected to be different from that of the diesel fuel. In this paper computational technique is used to study and compare the internal flow characteristics of diethyl ether, dimethyl ether and diesel fuel. The two phase flow model considering the fuel as a mixture of liquid and vapor is adopted for the simulation study. The injection pressure is varied from 100 to 400 bar and the flow characteristics of all three fuels are simulated and compared. Results indicate that all three fuels have distinct cavitating patterns owing to different property values. The dimethyl ether is found to be more cavitating than diesel and diethyl ether fuels as expected. The mass of fuel injected are found to be decreasing for the ether fuels when compared with diesel fuel at all injection pressures.

  9. On-line sample-pre-treatment schemes for trace-level determinations of metals by coupling flow injection or sequential injection with ICP-MS

    DEFF Research Database (Denmark)

    Wang, Jianhua; Hansen, Elo Harald

    2003-01-01

    for on-line matrix separation and pre-concentration of trace levels of metals with detection by ICP-MS. It highlights some of the frequently applied on-line, sample-pre-treatment schemes, including solid phase extraction (SPE), on-wall molecular sorption and precipitate/(co)-precipitate retention using...... a polytetrafluoroethylene (PTFE) knotted reactor (KR), solvent extraction-back extraction and hydride/vapor generation. It also addresses a novel, robust approach, whereby the protocol of SI-LOV-bead injection (BI) on-line separation and pre-concentration of ultra-trace levels of metals by a renewable microcolumn...

  10. Patient Comfort During Contrast Media Injection in Coronary Computed Tomographic Angiography Using Varying Contrast Media Concentrations and Flow Rates: Results From the EICAR Trial.

    Science.gov (United States)

    Kok, Madeleine; Mihl, Casper; Hendriks, Babs M F; Altintas, Sibel; Eijsvoogel, Nienke G; Kietselaer, Bas L J H; Wildberger, Joachim E; Das, Marco

    2016-12-01

    Pain sensation and extravasation are potential drawbacks of contrast media (CM) injection during computed tomographic angiography. The purpose was to evaluate safety and patient comfort of higher flow rates in different CM protocols during coronary computed tomographic angiography. Two hundred consecutive patients of a double-blind randomized controlled trial (NCT02462044) were analyzed. Patients were randomized to receive 94 mL of prewarmed iopromide 240 mg I/mL at 8.3 mL/s (group I), 75 mL of 300 mg I/mL at 6.7 mL/s (group II), or 61 mL of 370 mg I/mL at 5.4 mL/s (group III), respectively. Iodine delivery rate (2.0 g I/s) and total iodine load (22.5 g I) were kept identical. Outcome was defined as intravascular enhancement, patient comfort during injection, and injection safety, expressed as the occurrence of extravasation. Patients completed a questionnaire for comfort, pain, and stress during CM injection. Comfort was graded using a 5-point scale, 1 representing "very bad" and 5 "very well." Pain was graded using a 10-point scale, 0 representing "no pain" and 10 "severe pain." Stress was graded using a 5-point scale, 1 representing "no stress" and 5 "unsustainable stress." Mean enhancement levels within the coronary arteries were as follows: 437 ± 104 Hounsfield units (HU) (group I), 448 ± 111 HU (group II), and 447 ± 106 HU (group III), with P ≥ 0.18. Extravasation occurred in none of the patients. Median (interquartile range) for comfort, pain, and stress was, respectively, 4 (4-5), 0 (0-0), and 1 (1-2), with P ≥ 0.68. High flow rates of prewarmed CM were safely injected without discomfort, pain, or stress. Therefore, the use of high flow rates should not be considered a drawback for CM administration in clinical practice.

  11. Rapid Quantitation of Ascorbic and Folic Acids in SRM 3280 Multivitamin/Multielement Tablets using Flow-Injection Tandem Mass Spectrometry

    Energy Technology Data Exchange (ETDEWEB)

    Bhandari, Deepak [ORNL; Kertesz, Vilmos [ORNL; Van Berkel, Gary J [ORNL

    2013-01-01

    RATIONALE: Ascorbic acid (AA) and folic acid (FA) are water-soluble vitamins and are usually fortified in food and dietary supplements. For the safety of human health, proper intake of these vitamins is recommended. Improvement in the analysis time required for the quantitative determination of these vitamins in food and nutritional formulations is desired. METHODS: A simple and fast (~5 min) in-tube sample preparation was performed, independently for FA and AA, by mixing extraction solvent with a powdered sample aliquot followed by agitation, centrifugation, and filtration to recover an extract for analysis. Quantitative detection was achieved by flow-injection (1 L injection volume) electrospray ionization tandem mass spectrometry (ESI-MS/MS) in negative ion mode using the method of standard addition. RESULTS: Method of standard addition was employed for the quantitative estimation of each vitamin in a sample extract. At least 2 spiked and 1 non-spiked sample extract were injected in triplicate for each quantitative analysis. Given an injection-to-injection interval of approximately 2 min, about 18 min was required to complete the quantitative estimation of each vitamin. The concentration values obtained for the respective vitamins in the standard reference material (SRM) 3280 using this approach were within the statistical range of the certified values provided in the NIST Certificate of Analysis. The estimated limit of detections of FA and AA were 13 and 5.9 ng/g, respectively. CONCLUSIONS: Flow-injection ESI-MS/MS was successfully applied for the rapid quantitation of FA and AA in SRM 3280 multivitamin/multielement tablets.

  12. Implementation of suitable flow injection/sequential injection on-line sample pretreatment schemes. Separation and preconcentration procedures for the determination of trace metal concentrations by ETAAS and/or ICPMS

    DEFF Research Database (Denmark)

    Hansen, Elo Harald; Wang, Jianhua

    Despite their excellent analytical chemical capacities, ETAAS and ICPMS, nevertheless, often require suitable pretreatment of the sample material in order to obtain the necessary sensitivity and selectivity. Either in order to separate/preconcentrate the analyte material, or because of the presence...... of potentially interfering matrix constituents. Such pretreatments are advantageously performed in flow injection (FI) or sequential injection (SI) manifolds, where all appropriate unit operations can be effected under enclosed and strictly controlled conditions. Various separation/preconcentration procedures......, the ICPMS has potentially a larger volumetric capacity yet cannot accept organic solvents as these adversely will impair its performance. In the lecture, selected examples of separation/preconcentration FI/SI-procedures will be presented, with particular emphasis on the use of the novel “lab...

  13. Flow injection and sequential injection: The optimal solutions for executing appropriate on-line separation and preconcentration schemes for detection of trace-level concentrations of metals in complex matrices by ICPMS

    DEFF Research Database (Denmark)

    Hansen, Elo Harald

    , or because the analyte material, in addition to suitable separations, needs to be subjected to preconcentration. Such pretreatments schemes are advantageously performed in flow injection (FI) or sequential injection (SI) manifolds, where all unit operations can be effected on-line and under enclosed...... and strictly controlled conditions. Various separation/preconcentration procedures are feasible, such as liquid-liquid extraction encompassing back-extraction into an aqueous solution, (co)precipitation with collection in knotted reactors, adsorption on columns packed with hydrophophilic or hydrophobic...... as these adversely will impair its performance. In the lecture, selected examples of separation/preconcentration FI/SI-procedures for the determination of trace levels of metals will be presented, particular emphasis being placed on the use of the novel “lab-on-valve” (LOV) concept....

  14. Optimization of large-volume on-column injection conditions in gas chromatography by monitoring the actual carrier gas flow.

    NARCIS (Netherlands)

    Hankemeier, Th.; Kok, S.J.; Vreuls, J.J.; Brinkman, U.A.T.

    1999-01-01

    The change of the evaporation rate of the solvent during injection and evaporation is the most critical aspect during optimization of large-volume on-column injection conditions in gas chromatography. The change is caused by the pressure drop along the retention gap when using an early solvent

  15. Flow-Injection Amperometric Determination of Tacrine based on Ion Transfer across a Water–Plasticized Polymeric Membrane Interface

    Directory of Open Access Journals (Sweden)

    C. Rueda

    2007-07-01

    Full Text Available A flow-injection pulse amperometric method for determining tacrine, based onion transfer across a plasticized poly(vinyl chloride (PVC membrane, was developed. Afour-electrode potentiostat with ohmic drop compensation was used, while a flow-throughcell incorporated the four electrodes and the membrane, which containedtetrabutylammonium tetraphenylborate. The influence of the applied potential and of theflow-injection variables on the determination of tacrine was studied. In the selectedconditions, a linear relationship between peak height and tacrine concentration was foundup to 4x10-5M tacrine. The detection limit was 1x10-7M. Good repeatability was obtained.Some common ions and pharmaceutical excipients did not interfere.

  16. Differentiation of Aurantii Fructus Immaturus from Poniciri Trifoliatae Fructus Immaturus using flow-injection mass spectrometric (FIMS) metabolic fingerprinting method combined with chemometrics.

    Science.gov (United States)

    Zhao, Yang; Chang, Yuan-Shiun; Chen, Pei

    2015-03-25

    A flow-injection mass spectrometric metabolic fingerprinting method in combination with chemometrics was used to differentiate Aurantii Fructus Immaturus from its counterfeit Poniciri Trifoliatae Fructus Immaturus. Flow-injection mass spectrometric (FIMS) fingerprints of 9 Aurantii Fructus Immaturus samples and 12 Poniciri Trifoliatae Fructus Immaturus samples were acquired and analyzed using principal component analysis (PCA) and soft independent modeling of class analogy (SIMCA). The authentic herbs were differentiated from their counterfeits easily. Eight characteristic components which were responsible for the differences between the samples were tentatively identified. Furthermore, three out of the eight components, naringin, hesperidin, and neohesperidin, were quantified. The results are useful to help identify the authenticity of Aurantii Fructus Immaturus. Published by Elsevier B.V.

  17. Chemical reaction effect on an unsteady MHD free convection flow past a vertical porous plate in the presence of suction or injection

    Directory of Open Access Journals (Sweden)

    Shivaiah S.

    2012-01-01

    Full Text Available The objective of this paper is to analyze the effect of chemical reaction on unsteady magneto hydrodynamic free convective fluid flow past a vertical porous plate in the presence of suction or injection. The governing equations of the flow field are solved numerically by a finite element method. The effects of the various parameters on the velocity, temperature and concentration profiles are presented graphically and values of skin-friction coefficient, Nusselt number and Sherwood number for various values of physical parameters are presented through tables.

  18. Evaluation of Flow-Injection Tandem Mass Spectrometry for Rapid and High-Throughput Quantitative Determination of B-Vitamins in Nutritional Supplements

    Energy Technology Data Exchange (ETDEWEB)

    Bhandari, Deepak [ORNL; Van Berkel, Gary J [ORNL

    2012-01-01

    The use of flow-injection electrospray ionization tandem mass spectrometry for rapid and high-throughput mass spectral analysis of selected B-vitamins, viz. B1, B2, B3, B5, and B6, in nutritional formulations was demonstrated. A simple and rapid (~5 min) in-tube sample preparation was performed by adding extraction solvent to a powdered sample aliquot followed by agitation, centrifugation, and filtration to recover an extract for analysis. Automated flow injection introduced 1 L of the extracts directly into the mass spectrometer ion source without chromatographic separation. Sample-to-sample analysis time was 60 s representing significant improvement over conventional liquid chromatography approaches which typically require 25-45 min, and often require more significant sample preparation procedures. Quantitative capabilities of the flow-injection analysis were tested using the method of standard additions and NIST standard reference material (SRM 3280) multivitamin/multielement tablets. The quantity determined for each B-vitamin in SRM 3280 was within the statistical range provided for the respective certified values. The same sample preparation and analysis approach was also applied to two different commercial vitamin supplement tablets and proved to be successful in the quantification of the selected B-vitamins as evidenced by an agreement with the labels values and the results obtained using isotope dilution liquid chromatography/mass spectrometry.

  19. Highly integrated flow assembly for automated dynamic extraction and determination of readily bioaccessible chromium(VI) in soils exploiting carbon nanoparticle-based solid-phase extraction

    Energy Technology Data Exchange (ETDEWEB)

    Rosende, Maria; Miro, Manuel; Cerda, Victor [University of the Balearic Islands, Department of Chemistry, Palma de Mallorca (Spain); Segundo, Marcela A.; Lima, Jose L.F.C. [University of Porto, REQUIMTE, Department of Chemistry, Faculty of Pharmacy, Porto (Portugal)

    2011-06-15

    An automated dynamic leaching test integrated in a portable flow-based setup is herein proposed for reliable determination of readily bioaccessible Cr(VI) under worst-case scenarios in soils containing varying levels of contamination. The manifold is devised to accommodate bi-directional flow extraction followed by processing of extracts via either in-line clean-up/preconcentration using multi-walled carbon nanotubes or automatic dilution at will, along with Cr(VI) derivatization and flow-through spectrophotometric detection. The magnitude of readily mobilizable Cr(VI) pools was ascertained by resorting to water extraction as promulgated by current standard leaching tests. The role of carbon nanomaterials for the uptake of Cr(VI) in soil leachates and the configuration of the packed column integrated in the flow manifold were investigated in detail. The analytical performance of the proposed system for in vitro bioaccessibility tests was evaluated in chromium-enriched soils at environmentally relevant levels and in a standard reference soil material (SRM 2701) with a certified value of total hexavalent chromium. The automated method was proven to afford unbiased assessment of water-soluble Cr(VI) in soils as a result of the minimization of the chromium species transformation. By combination of the kinetic leaching profile and a first-order leaching model, the water-soluble Cr(VI) fraction in soils was determined in merely 6 h against >24 h taken in batchwise steady-state standard methods. (orig.)

  20. Quantification of a maximum injection volume of CO2 to avert geomechanical perturbations using a compositional fluid flow reservoir simulator

    Science.gov (United States)

    Jung, Hojung; Singh, Gurpreet; Espinoza, D. Nicolas; Wheeler, Mary F.

    2018-02-01

    Subsurface CO2 injection and storage alters formation pressure. Changes of pore pressure may result in fault reactivation and hydraulic fracturing if the pressure exceeds the corresponding thresholds. Most simulation models predict such thresholds utilizing relatively homogeneous reservoir rock models and do not account for CO2 dissolution in the brine phase to calculate pore pressure evolution. This study presents an estimation of reservoir capacity in terms of allowable injection volume and rate utilizing the Frio CO2 injection site in the coast of the Gulf of Mexico as a case study. The work includes laboratory core testing, well-logging data analyses, and reservoir numerical simulation. We built a fine-scale reservoir model of the Frio pilot test in our in-house reservoir simulator IPARS (Integrated Parallel Accurate Reservoir Simulator). We first performed history matching of the pressure transient data of the Frio pilot test, and then used this history-matched reservoir model to investigate the effect of the CO2 dissolution into brine and predict the implications of larger CO2 injection volumes. Our simulation results -including CO2 dissolution- exhibited 33% lower pressure build-up relative to the simulation excluding dissolution. Capillary heterogeneity helps spread the CO2 plume and facilitate early breakthrough. Formation expansivity helps alleviate pore pressure build-up. Simulation results suggest that the injection schedule adopted during the actual pilot test very likely did not affect the mechanical integrity of the storage complex. Fault reactivation requires injection volumes of at least about sixty times larger than the actual injected volume at the same injection rate. Hydraulic fracturing necessitates much larger injection rates than the ones used in the Frio pilot test. Tested rock samples exhibit ductile deformation at in-situ effective stresses. Hence, we do not expect an increase of fault permeability in the Frio sand even in the presence of

  1. Establish an automated flow injection ESI-MS method for the screening of fragment based libraries: Application to Hsp90.

    Science.gov (United States)

    Riccardi Sirtori, Federico; Caronni, Dannica; Colombo, Maristella; Dalvit, Claudio; Paolucci, Mauro; Regazzoni, Luca; Visco, Carlo; Fogliatto, Gianpaolo

    2015-08-30

    ESI-MS is a well established technique for the study of biopolymers (nucleic acids, proteins) and their non covalent adducts, due to its capacity to detect ligand-target complexes in the gas phase and allows inference of ligand-target binding in solution. In this article we used this approach to investigate the interaction of ligands to the Heat Shock Protein 90 (Hsp90). This enzyme is a molecular chaperone involved in the folding and maturation of several proteins which has been subjected in the last years to intensive drug discovery efforts due to its key role in cancer. In particular, reference compounds, with a broad range of dissociation constants from 40pM to 100μM, were tested to assess the reliability of ESI-MS for the study of protein-ligand complexes. A good agreement was found between the values measured with a fluorescence polarization displacement assay and those determined by mass spectrometry. After this validation step we describe the setup of a medium throughput screening method, based on ESI-MS, suitable to explore interactions of therapeutic relevance biopolymers with chemical libraries. Our approach is based on an automated flow injection ESI-MS method (AFI-MS) and has been applied to screen the Nerviano Medical Sciences proprietary fragment library of about 2000 fragments against Hsp90. In order to discard false positive hits and to discriminate those of them interacting with the N-terminal ATP binding site, competition experiments were performed using a reference inhibitor. Gratifyingly, this group of hits matches with the ligands previously identified by NMR FAXS techniques and confirmed by X-ray co-crystallization experiments. These results support the use of AFI-MS for the screening of medium size libraries, including libraries of small molecules with low affinity typically used in fragment based drug discovery. AFI-MS is a valid alternative to other techniques with the additional opportunities to identify compounds interacting with

  2. Exploitability Assessment with TEASER

    Science.gov (United States)

    2017-05-01

    exploits. We saw this as an advantage of our dataset because we had to confirm that either a bug was exploitable or not exploitable. For the 28 CHAPTER 5...corruption which demonstrates that there is very little activity within c-ares to take advantage of after the heap corruption. This idea is in line with the...remote code execution POCs. 42 Bibliography [1] Analyze crashes to find security vulnerabilities in your apps . https: //blogs.msdn.microsoft.com

  3. Wall-slip of highly filled powder injection molding compounds: Effect of flow channel geometry and roughness

    Science.gov (United States)

    Hausnerova, Berenika; Sanetrnik, Daniel; Paravanova, Gordana

    2014-05-01

    The paper deals with the rheological behavior of highly filled compounds proceeded via powder injection molding (PIM) and applied in many sectors of industry (automotive, medicine, electronic or military). Online rheometer equipped with slit dies varying in surface roughness and dimensions was applied to investigate the wall-slip as a rheological phenomenon, which can be considered as a parameter indicating the separation of compound components (polymer binder and metallic powder) during high shear rates when injection molded.

  4. Anthropology of sexual exploitation

    Directory of Open Access Journals (Sweden)

    Lalić Velibor

    2009-01-01

    Full Text Available In this paper, the authors observe sexual exploitation from an anthropological perspective. They analyze the rational, ethical, emotional and mythological dimensions of human sexuality. Consequently, after setting the phenomenon in a social and historical context, sexual exploitation is closely observed in the contemporary age. Based on thoughts of relevant thinkers, they make the conclusion that the elimination of sexual exploitation is not an utterly legal issue, but political and economical issues as well. Namely, legal norms are not sufficient to overcome sexual exploitation, but, political and economical relationships in contemporary societies, which will be based on sincere equal opportunities must be established.

  5. How Flow Injection Analysis (FIA) over the past 25 years has changed our way of performing chemical analyses

    DEFF Research Database (Denmark)

    Hansen, Elo Harald; Miró, Manuel

    2007-01-01

    -on-Valve (LOV), have offered, we emphasize assays based on kinetic discrimination schemes, where, even subtle, differences in the reaction rates of the chemical reactions that occur are judiciously exploited. We give a number of examples, covering homogeneous as well as heterogeneous conversions techniques...

  6. Parametric effect on the mixing of the combination of a hydrogen porthole with an air porthole in transverse gaseous injection flow fields

    Science.gov (United States)

    Li, Lang-quan; Huang, Wei; Yan, Li; Li, Shi-bin

    2017-10-01

    The dual transverse injection system with a front hydrogen porthole and a rear air porthole arranged in tandem is proposed, and this is a realistic approach for mixing enhancement and penetration improvement of transverse injection in a scramjet combustor. The influence of this dual transverse injection system on mixing characteristics has been evaluated numerically based on grid independency analysis and code validation. The numerical approach employed in the current study has been validated against the available experimental data in the open literature, and the predicted wall static pressure distributions show reasonable agreement with the experimental data for the cases with different jet-to-crossflow pressure ratios. The obtained results predicted by the three-dimensional Reynolds-average Navier - Stokes (RANS) equations coupled with the two equation k-ω shear stress transport (SST) turbulence model show that the air pothole has an great impact on penetration depth and mixing efficiency, and the effect of air jet on flow field varies with different values of the aspect ratio. The air porthole with larger aspect ratio can increase the fuel penetration depth. However, when the aspect ratio is relatively small, the fuel penetration depth decreases, and even smaller than that of the single injection system. At the same time, the air pothole has a highly remarkable improvement on mixing efficiency, especially in the near field. The smaller the aspect ratio of the air porthole is, the higher the mixing efficiency in the near field is. This is due to its larger circulation in the near field. The dual injection system owns more losses of stagnation pressure than the single injection system.

  7. Flow injection analysis-flame atomic absorption spectrometry system for indirect determination of sulfite after on-line reduction of solid-phase manganese (IV) dioxide reactor.

    Science.gov (United States)

    Zare-Dorabei, Rouholah; Boroun, Shokoufeh; Noroozifar, Meissam

    2018-02-01

    A new and simple flow injection method followed by atomic absorption spectrometry was developed for indirect determination of sulfite. The proposed method is based on the oxidation of sulfite to sulphate ion using solid-phase manganese dioxide (30% W/W suspended on silica gel beads) reactor. MnO2 will be reduced to Mn(II) by sample injection in to the column under acidic carrier stream of HNO3 (pH 2) with flow rate of 3.5mLmin-1 at room temperature. Absorption measurement of Mn(II) which is proportional to the concentration of sulfite in the sample was carried out by atomic absorption spectrometry. The calibration curve was linear up to 25mgL-1 with a detection limit (DL) of 0.08mgL-1 for 400µL injection sample volume. The presented method is efficient toward sulfite determination in sugar and water samples with a relative standard deviation (RSD) less than 1.2% and a sampling rate of about 60h-1. Copyright © 2017 Elsevier B.V. All rights reserved.

  8. EXPLOITATION OF GRANITE BOULDER

    Directory of Open Access Journals (Sweden)

    Ivan Cotman

    1994-12-01

    Full Text Available The processes of forming, petrography, features, properties and exploitation of granite boulders are described. The directional drilling and black powder blasting is the succesful method in exploitation of granite boulders (boulder technology (the paper is published in Croatian.

  9. A Spectrophotometric Flow Injection Method for Determination of Ultratrace Amounts of Phenylhydrazine by Its Inhibition Effect on the Reaction of Thionin and Nitrite

    Directory of Open Access Journals (Sweden)

    M. Keyvanfard

    2013-01-01

    Full Text Available A simple flow injection colorimetric procedure for determining phenylhydrazine was established. It is based on the reaction of phenylhydrazine in sulfuric acid with thionin and sodium nitrite. Reaction was monitored spectrophotometrically by measuring thionin absorbance at λmax=602 nm. A standard or sample solution was injected into the sulfuric acid stream, which was then merged with sodium nitrite stream and thionin stream. Optimum conditions for determining phenylhydrazine were investigated by univariate method. Under the optimum conditions, a linear calibration graph was obtained over the range 0.05–0.60 μmol L−1, and the detection limit was 0.027 μmol L−1(s/n=3. The proposed method has been satisfactorily applied to the determination of phenylhydrazine in human serum and water samples.

  10. Flow-injection on-line electrochemical separation/determination of ions using a two-step oil/water-type flow cell system.

    Science.gov (United States)

    Gohara, Emi; Osakai, Toshiyuki

    2010-01-01

    A flow system for electrochemical separation and detection of ions was constructed by connecting two oil/water (O/W)-type flow cells, in which a long polarizable O/W interface was formed at the inner surface of a porous poly(tetrafluoroethylene) (PTFE) tube. Using this system, acetylcholine and choline ions, whose ion-transfer potentials are different by only 60 mV, could be separated and determined simultaneously. It was thus shown that the present flow system is promising for the electrochemical flow separation/detection of ions and, in principle, also for electrochromatographic separation of ions.

  11. Assessment of injected warm plumes along a free surface flow channel using fiber-optic distributed temperature sensing and numerical simulations

    Science.gov (United States)

    Le Lay, Hugo; Thomas, Zahra; Rouault, François; Pichelin, Pascal; Bour, Olivier; Moatar, Florentina

    2017-04-01

    Understanding and predicting stream thermal regimes is a key goal for aquatic ecosystems resiliency to climate change. Mapping thermal anomalies finely becomes feasible thanks to methods such as fiber-optic distributed temperature sensing (FO-DTS). Despite being the main thermal anomalies in stream, groundwater inflows are difficult to detect because of high water stages and turbulent stream flow. We hypothesized that thresholds in flow regime and hydraulic parameters may affect thermal regime characterization. Our main objective was to test and validate the use of FO-DTS for the quantification of inflows in order to determine the physical processes behind these thresholds. Experiments were carried out outdoor, using an open flow hydraulic channel. A warm water tank was used to simulate groundwater inflows with known discharge rates and temperatures. These discharge rates varied between 4 and 72% of the channel flow. Numerical experiments were also conducted to test the consistency of our experimental results and discriminate the effect of inflow rate and hydraulic parameters. The water temperature in the channel was monitored by Fiber-Optic Distributed Temperature Sensing with cables set on two lines, over three depths. The injected warm plume was tracked along the channel and across the water stage to estimate temperature increases it induced. A relationship was found between these thermal anomalies and flow dynamic, defining different types of flow configurations. For given channel flow rate and water stage, a threshold for the inflow rate was identified at which the injected plume is not detectable by our means. The effect of the channel flow velocity over the plume spreading appears clearly with a dominance of advection for high flow rate. In addition, outdoor experiments were affected by atmospheric conditions (air temperature, solar radiation, etc.) while simulations allowed refining results without external artefacts and showed a good fit with measurements

  12. Establishment of a finite element model for extracting chemical reaction kinetics in a micro-flow injection system with high throughput sampling.

    Science.gov (United States)

    Wu, Zeng-Qiang; Du, Wen-Bin; Li, Jin-Yi; Xia, Xing-Hua; Fang, Qun

    2015-08-01

    Numerical simulation can provide valuable insights for complex microfluidic phenomena coupling mixing and diffusion processes. Herein, a novel finite element model (FEM) has been established to extract chemical reaction kinetics in a microfluidic flow injection analysis (micro-FIA) system using high throughput sample introduction. To reduce the computation burden, the finite element mesh generation is performed with different scales based on the different geometric sizes of micro-FIA. In order to study the contribution of chemical reaction kinetics under non-equilibrium condition, a pseudo-first-order chemical kinetics equation is adopted in the numerical simulations. The effect of reactants diffusion on reaction products is evaluated, and the results demonstrate that the Taylor dispersion plays a determining role in the micro-FIA system. In addition, the effects of flow velocity and injection volume on the reaction product are also simulated. The simulated results agree well with the ones from experiments. Although gravity driven flow is used to the numerical model in the present study, the FEM model also can be applied into the systems with other driving forces such as pressure. Therefore, the established FEM model will facilitate the understanding of reaction mechanism in micro-FIA systems and help us to optimize the manifold of micro-FIA systems. Copyright © 2015 Elsevier B.V. All rights reserved.

  13. On-line monitoring of bioreactions of Bacillus polymyxa and Klebsiella oxytoca by membrane introduction tandem mass spectrometry with flow injection analysis sampling

    Energy Technology Data Exchange (ETDEWEB)

    Hayward, M.J.; Kotiaho, Tapio; Lister, A.K.; Cooks, R.G.; Austin, G.D.; Narayan, Ramani; Tsao, G.T. (Purdue Univ., West Lafayette, IN (USA))

    1990-09-01

    Membrane introduction mass spectrometry with flow injection analysis sampling has been utilized for on-line monitoring of the major products and the volatile metabolites of fermentation of the Bacillus polymyxa and Klebsiella oxytoca organisms. A flow injection sampling system was used to rapidly deliver fermentation broth or an external standard to the mass spectrometer. Analyte introduction occurred via a direct insertion membrane probe in which the aqueous solutions flowed past a membrane located within the ion source of the mass spectrometer. For both organisms, concentrations of the liquid-phase products acetic acid, acetoin, 2,3-butanediol, and ethanol, were monitored as a function of time after permeation through the membrane and ionization by chemical ionization. Tandem mass spectrometry confirmed that these measurements were made without interference. Off-line gas chromatography was utilized to test the accuracy of these measurements, and excellent agreement was found. The use of tandem mass spectrometry has allowed the detection of additional compounds that were previously not known to be present in measurable amounts.

  14. Flow injection on-line dialysis coupled to high performance liquid chromatography for the determination of some organic acids in wine.

    Science.gov (United States)

    Kritsunankul, Orawan; Pramote, Benjaporn; Jakmunee, Jaroon

    2009-09-15

    A combined system of flow injection on-line dialysis sample pretreatment and high performance liquid chromatographic separation/detection (FID-HPLC) was developed for simultaneous determination of six organic acids (tartaric, malic, lactic, acetic, citric and succinic acids). A sample or mixed standard solution (400 microL) was injected into a donor stream (water) of FID system and was pushed further through a dialysis cell, while an acceptor solution (water) was held in the opposite side of the dialysis membrane. The dialysate containing organic acids in the acceptor solution was then flowed to an injection loop of the HPLC valve, where it was further injected into the HPLC system and analysed under normal HPLC conditions, using a reversed-phase (C(18)) analytical column and UV detection (210 nm). The order of elution was tartaric, malic, lactic, acetic, citric and succinic acids with the analysis time of 8 min. The FID system could be operated in parallel with HPLC separation, providing sample throughput of 7.5h(-1). Dialysis efficiencies of six organic acids were in range of 4.6-9.5%. Calibration graphs for all the mentioned organic acids were linear over the range of 250-7500 mg L(-1). Precisions for all the organic acids were within 5.4%. The proposed system was successfully applied for analysis of some Thai wines. By spiking wine samples with mixed acid standard solutions, the percentage recoveries in range of 84-104 were found. This system has advantages of fast and high degrees of automation for dialysis sample pretreatment, on-line sample separation and dilution, good clean-up for prolongation of life-time of the HPLC column and low consumption of chemicals and materials.

  15. Determination of ultra-trace mercury(II) by flow-injection/anodic stripping voltammetry using a track-etched microporous membrane electrode.

    Science.gov (United States)

    Mizuguchi, Hitoshi; Numata, Kentaro; Monma, Chiaki; Iiyama, Masamitsu; Tachibana, Kazuhiro; Nishina, Tatsuo; Shida, Junichi

    2013-01-01

    A new flow-injection/anodic stripping voltammetry has been demonstrated to assess ultra-trace mercury(II) using track-etched microporous membrane electrodes. The electrodes were prepared by the sputtering of gold or platinum onto both sides of a membrane filter with a smooth flat surface and with cylindrical pores having uniform diameter. The deposition of mercury from a mercury(II) solution was performed while the sample solution flowed through the membrane electrodes. After the deposition step, an anodic stripping voltammogram was obtained by sweeping the potential from 0 to +0.8 V vs. Ag/AgCl. In this case, the sample solution flowed through the pores of the 10-μm-thick membrane filters. Efficient electrolysis occurred during passage of the sample solution through the electrode, of which the pore size was 0.4 μm. In this study, the voltammetry described above was demonstrated using an FIA system. The continuous-flow mode showed a detection limit of 0.04 μg L(-1) when the experimental conditions of the flow rate and the deposition time were set at 0.5 mL min(-1) and 180 s. In the sample-injection mode equipped with a 1-mL sample loop, a linear relation was found for 0.5-4.0 μg L(-1) of a mercury(II) standard solution (r = 0.995). The detection limit was 0.05 μg L(-1). This method was applied to the ultra-trace determination of mercury(II) in river-water samples.

  16. Numerical and Experimental Investigations of Steady Micro-Tip Injection on a Subsonic Axial-Flow Compressor Rotor

    Directory of Open Access Journals (Sweden)

    Xingen Lu

    2006-01-01

    tip-clearance flow manipulation. The repositioning of the tip-clearance vortex further towards the trailing edge of the blade passage and delaying the movement of incoming/tip-clearance flow interface to the leading edge plane are the physical mechanisms responsible for extending the compressor stall margin.

  17. Autoamostrador de baixo custo para análise por injeção em fluxo A low cost autosampler for flow injection analysis

    Directory of Open Access Journals (Sweden)

    Marcos Y. Kamogawa

    2009-01-01

    Full Text Available This paper describes a homemade autosampler for flow injection analysis (FIA, constructed with two step motors from old floppy disk drives (5¼-inch. The autosampler was connected to a computer through the parallel port and the sampling process was controlled by software in Quick Basic. The performance of the system was assessed by the determination of ammonium, based on the gaseous diffusion into a bromocresol purple solution, following the spectrophotometric determination of change in absorbance. The easy and simple construction is the main characteristics of this equipment and analytical results with RSD lower than 1% were obtained.

  18. Dilution Methods in Flow Injection Analysis. Evaluation of Different Approaches as Exemplified for the Determination of Nitrosyl in Concentrated Sulphuric Acid

    DEFF Research Database (Denmark)

    Jørgensen, Ulla Vang; Nielsen, Steffen; Hansen, Elo Harald

    1998-01-01

    in conjunction with knotted reactors of relatively large internal diameter (1.5 mm). The optimized FI-manifold was used with the Griess method for the spectrophotometric assay of nitrosyl (nitrite) in standards prepared in the matrix of concentrated sulphuric acid (detection limit 0.16 mg/l NO+-N (3s......Instigated by developing a flow injection procedure for assay of nitrosyl in concentrated sulphuric acid, different approaches for reliable and robust on-line dilution in FIA were evaluated. These comprised the application of mixing tees in conjunction with mixing coils (including knotted reactors...

  19. On-line Speciation of Cr(III) and Cr(VI) by Flow Injection Analysis With Spectrophotometric Detection and Chemometrics

    DEFF Research Database (Denmark)

    Diacu, Elena; Andersen, Jens Enevold Thaulov

    2003-01-01

    A flow injection system has been developed, for on-line speciation. of Cr(III) and Cr(VI) by the Diphenylcarbazide (DPC) method with H2O2 oxidation followed by spectrophotometric detection at the 550 nm wavelength. The data thus obtained were subjected to a chemometric analysis (PLS), which showed...... that it was possible to obtain reliable predictions of Cr(III) and Cr(VI) species. The method was validated on samples of stainless steel. In order to facilitate analysis of stainless-steel samples it was essential to perform a step of evaporation to dryness followed by re-dissolution. The analysis showed that species...

  20. A Study of the Geo-Herbalism of Evodiae Fructus Based on a Flow-Injection Mass Spectrometric Fingerprinting Method Combined with Chemometrics

    Directory of Open Access Journals (Sweden)

    Yang Zhao

    2015-02-01

    Full Text Available A flow-injection mass spectrometric (FIMS fingerprinting method in combination with principal component analysis (PCA was used to study the geo-herbalism of Evodiae Fructus (EF samples. Twenty four EF samples from different regions in China were collected and analyzed. The PCA scores plot showed that the samples from Guizhou Province were scattered in different groups, however, most of the samples from other provinces were basically scattered in the same group. Nine characteristic compounds responsible for the classification of the samples were tentatively characterized. These nine compounds might help differentiating EF samples from different regions.

  1. Medroxyprogesterone Injection

    Science.gov (United States)

    Medroxyprogesterone intramuscular (into a muscle) injection and medroxyprogesterone subcutaneous (under the skin) injection are used to prevent pregnancy. Medroxyprogesterone subcutaneous injection is also used to treat endometriosis ( ...

  2. Determination of pipemidic acid based on flow-injection chemiluminescence due to energy transfer from peroxynitrous acid synthesized on-line.

    Science.gov (United States)

    Liang, Yao-Dong; Song, Jun-Feng; Tian, Tian

    2004-12-01

    A flow-injection chemiluminescence (CL) method for the determination of pipemidic acid is described. It is based on energy transfer from excited state peroxynitrous acid to pipemidic acid, in which the excited state peroxynitrous acid is synthesized on-line by the mixing of acid hydrogen peroxide with nitrite in a flow system and the CL is from two excited states of pipemidic acid. The proposed method allows the measurement of pipemidic acid over the range of 2.0 x 10(-7)-2.0 x 10(-5) mol l(-1) . The detection limit is 6.3 x 10(-8) mol l(-1), and the relative standard deviation for 2.0 x 10(-6) mol l(-1) pipemidic acid (n = 9) is 0.9%. This method was evaluated by the analysis of pipemidic acid in pharmaceutical preparations.

  3. Flow-injection potentiometric determination of triiodide by plasticized poly(vinyl chloride) membrane electrodes and its application to the determination of chlorine-containing disinfectants.

    Science.gov (United States)

    Ortuño, Joaquín A; Sánchez-Pedreño, Concepción; Hernández, Jorge; Oliva, Domingo J

    2005-03-15

    Plasticized poly(vinyl chloride) (PVC) membranes of different compositions were tested for use in the construction of potentiometric flow detectors for triiodide. A membrane with a 2:1 (w/w) 2-nitrophenyl octyl ether to PVC ratio was selected. The influence of thiosulphate in the carrier solution composition and of the flow-injection variables on the determination of triiodide was studied. In the selected conditions, a linear relationship between peak height and log[I(3)(-)] was obtained between 5 x 10(-6) and 1 x 10(-4)moll(-1) triiodide. Peak height relative standard deviations for 2 x 10(-5) and 1 x 10(-4)moll(-1) triiodide were +/-0.4 and +/-1.8%, respectively, and sampling frequency was 80 samples per hour. The method proposed was applied satisfactorily to the iodometric determination of different chlorine-containing disinfectants, among them trichloroisocyanuric acid and dichloroisocyanurate in several types of commercial sample.

  4. Determination of Formaldehyde in Frozen Fish with Formaldehyde Dehydrogenase Using a Flow Injection System with an Incorporated Gel-filtration Chromatography Column

    DEFF Research Database (Denmark)

    Bechmann, Iben Ellegaard

    1996-01-01

    A flow injection analysis (FIA) system for determination of formaldehyde in frozen fish products is described. The system provides a rapid and selective determination of formaldehyde in aqueous fish extracts by the combination of a deproteinization procedure and a stopped-flow enzymatic approach...... in a FIA system. The FIA system is furnished with a gel-filtration chromatography column for on-line removal of the proteins from the extract before the enzymatic analysis is performed. Compared with the standard methods for determination of formaldehyde in fish products the present method is much faster...... and less affected by interferences. The limit of detection for the proposed method is 2.5 mg/l of formaldehyde. The sampling frequency is about 10 determinations per hour....

  5. Heat Transfer Analysis for Stationary Boundary Layer Slip Flow of a Power-Law Fluid in a Darcy Porous Medium with Plate Suction/Injection.

    Science.gov (United States)

    Aziz, Asim; Ali, Yasir; Aziz, Taha; Siddique, J I

    2015-01-01

    In this paper, we investigate the slip effects on the boundary layer flow and heat transfer characteristics of a power-law fluid past a porous flat plate embedded in the Darcy type porous medium. The nonlinear coupled system of partial differential equations governing the flow and heat transfer of a power-law fluid is transformed into a system of nonlinear coupled ordinary differential equations by applying a suitable similarity transformation. The resulting system of ordinary differential equations is solved numerically using Matlab bvp4c solver. Numerical results are presented in the form of graphs and the effects of the power-law index, velocity and thermal slip parameters, permeability parameter, suction/injection parameter on the velocity and temperature profiles are examined.

  6. Crosslinked poly (4-vinylpyridine-ethylene glycol dimethacrylate) used for preconcentration of Cd(II) and its determination by flow injection flame atomic absorption spectrometry.

    Science.gov (United States)

    Tarley, César Ricardo Teixeira; Farias, Natália Cristina Botteon; Lima, Giovana de Fátima; de Oliveira, Fernanda Midori; Bonfílio, Rudy; Dragunski, Douglas Cardoso; Clausen, Débora Nobile; Segatelli, Mariana Gava

    2014-01-01

    The main purpose of this research was to synthesize crosslinked poly(4-vinylpyridine-ethylene glycol dimethacrylate) and evaluate its feasibility for highly sensitive and selective determination of Cd in water samples by using flow injection flame atomic absorption spectrometry. The crosslinked polymer, prepared by bulk polymerization, was characterized by FTIR spectrometry and scanning electron microscopy. The flow injection solid-phase method was based on preconcentration of 20.0 mL of sample through 100 mg of the polymer packed into a minicolumn at pH 8.25 using a flow rate of 6.0 mL/min, followed by elution with 1.0 M HNO3. The sample solution parameters influencing the preconcentration behavior of Cd ions, such as pH, buffer concentration, and flow rate, were simultaneously studied and optimized using a Doehlert matrix. Values of 0.10 microg/L, 2.0-210 microg/L, 32.3, 18/h, 9.7/min, and 0.62 mL were obtained for LOD, linear range, preconcentration factor, sample throughput, concentration efficiency, and consumption index, respectively. The effect of the presence of the inorganic cations Pb(II), U(IV), Co(II), Hg(II), Cu(II), As(II), Mg(II), Sb(III), Ni(II), Th(IV), Ba(II), and Ca(II) on the method was studied, and the preconcentration of Cd was observed to have no interference. The accuracy of the method was assessed by analysis of natural water samples using addition and recovery tests and inductively coupled plasma/MS as a reference technique, as well as by analysis of a standard reference material of trace elements in water.

  7. Arterio-venous concentration difference of [51Cr]EDTA after a single injection in man. Significance of renal function and local blood flow

    DEFF Research Database (Denmark)

    Rehling, M; Hyldstrup, Lars; Henriksen, Jens Henrik

    1989-01-01

    introduced in the measurement of renal plasma clearance and total plasma clearance by using venous blood samples instead of arterial. In 13 patients with GFR ranging from 29 to 150 ml min-1, Ca was higher than Cv immediately after the injection. After mean 38 min (range 12-82 min) the two curves crossed......, and 180-300 min post-injection (p.i.) Cv was 5.9% higher than Ca (range 0.5-13.9%, P less than 0.001). The more reduced renal function, the smaller was the concentration difference. The areas under the arterial and the venous plasma concentration curves did not differ significantly at either 0-infinity......, whereas the difference was very sensitive to even small changes in forearm blood flow within the physiological range. For measurement of renal plasma clearance it is recommended to use one long period: from the time of injection until 300 min p.i. or longer. If the clearance period is too short, the use...

  8. Preparation of Fe(3)O(4)@C@CNC multifunctional magnetic core/shell nanoparticles and their application in a signal-type flow-injection photoluminescence immunosensor.

    Science.gov (United States)

    Chu, Chengchao; Li, Meng; Li, Long; Ge, Shenguang; Ge, Lei; Yu, Jinghua; Yan, Mei; Song, Xianrang

    2013-11-01

    We describe here the preparation of carbon-coated Fe3O4 magnetic nanoparticles that were further fabricated into multifunctional core/shell nanoparticles (Fe3O4@C@CNCs) through a layer-by-layer self-assembly process of carbon nanocrystals (CNCs). The nanoparticles were applied in a photoluminescence (PL) immunosensor to detect the carcinoembryonic antigen (CEA), and CEA primary antibody was immobilized onto the surface of the nanoparticles. In addition, CEA secondary antibody and glucose oxidase were covalently bonded to silica nanoparticles. After stepwise immunoreactions, the immunoreagent was injected into the PL cell using a flow-injection PL system. When glucose was injected, hydrogen peroxide was obtained because of glucose oxidase catalysis and quenched the PL of the Fe3O4@C@CNC nanoparticles. The here proposed PL immunosensor allowed us to determine CEA concentrations in the 0.005–50 ng·mL-1 concentration range, with a detection limit of 1.8 pg·mL-1.

  9. Sumatriptan Injection

    Science.gov (United States)

    Alsuma® Injection ... Imitrex® Injection ... Sumavel® Injection ... Sumatriptan injection is used to treat the symptoms of migraine headaches (severe, throbbing headaches that sometimes are accompanied by ...

  10. AN APPLICATION OF FLOW INJECTION ANALYSIS WITH GAS DIFFUSION AND SPECTROPHOTOMETRIC DETECTION FOR THE MONITORING OF DISSOLVED SULPHIDE CONCENTRATION IN ENVIRONMENTAL SAMPLES

    Directory of Open Access Journals (Sweden)

    Malwina Cykowska

    2014-10-01

    Full Text Available The monitoring of the concentration of sulphide is very important from the environment point of view because of high toxicity of hydrogen sulphide. What is more hydrogen sulphide is an important pollution indicator. In many cases the determination of sulphide is very difficult due to complicated matrix of some environmental samples, which causes that most analytical methods cannot be used. Flow injection analysis allows to avoid matrix problem what makes it suitable for a wide range of applications in analytical laboratories. In this paper determination of dissolved sulphide in environmental samples by gas-diffusion flow injection analysis with spectrophotometric detection was presented. Used gas-diffusion separation ensures the elimination of interferences caused by sample matrix and gives the ability of determination of sulphides in coloured and turbid samples. Studies to optimize the measurement conditions and to determine the value of the validation parameters (e.g. limit of detection, limit of quantification, precision, accuracy were carried out. Obtained results confirm the usefulness of the method for monitoring the concentration of dissolved sulphides in water and waste water. Full automation and work in a closed system greatly reduces time of analysis, minimizes consumption of sample and reagents and increases safety of analyst’s work.

  11. Chemiluminescent determination of vanadium(IV) using a cinchomeronic hydrazide-H{sub 2}O{sub 2} system and flow injection analysis

    Energy Technology Data Exchange (ETDEWEB)

    Pradana Perez, J.A. [Departamento de Ciencias Analiticas, Facultad de Ciencias, Universidad Nacional de Educacion a Distancia, c/Senda del Rey 9, 28040 Madrid (Spain); Alegria, J.S. Durand [Departamento de Ciencias Analiticas, Facultad de Ciencias, Universidad Nacional de Educacion a Distancia, c/Senda del Rey 9, 28040 Madrid (Spain); Hernando, P. Fernandez [Departamento de Ciencias Analiticas, Facultad de Ciencias, Universidad Nacional de Educacion a Distancia, c/Senda del Rey 9, 28040 Madrid (Spain)]. E-mail: pfhernando@ccia.uned.es; Sierra, A. Narros [Departamento de Ingenieria Quimica y del Medio Ambiente, Escuela Tecnica Superior de Ingenieros Industriales, Universidad Politecnica de Madrid, Madrid (Spain)

    2005-04-22

    This paper proposes a new chemiluminescent flow injection analysis (FIA) method for the determination of vanadium(IV) ions in aqueous media. The method is based on the chemiluminescent reaction that occurs between cinchomeronic hydrazide (CH) and hydrogen peroxide in a strongly alkaline medium, in which vanadium(IV) acts as a catalyst. The chemical and physical variables involved in the flow injection system are optimised using a modified simplex method. Vanadium ions can be detected in the 0.08 and 1.00 {mu}g mL{sup -1} range; the detection limit for a signal-to-noise ratio of 3 is 0.08 {mu}g mL{sup -1}. Great variations in the quantum yield were observed when cobalt(II), chromium(III), copper(II) and/or nickel(II) were present in the reaction medium. The proposed method is selective and simple, and can be successfully used to analyse water samples without the need for separation or preconcentration processes.

  12. Chemiluminescence method for the assay of perphenazine in drug formulation using permanganate in sulphuric acid with flow injection technique and a chemometrical optimization approach.

    Science.gov (United States)

    Sultan, S M; Abdennabi, A M; Almuaibed, A M

    1999-08-09

    An accurate selective flow injection chemiluminescence (CL) method for the assay of perphenazine was explored. In the method 394 ppm permanganate solution was used as a chemiluminogenic reagent in 0.289 mol dm(-3) sulphuric acid media. A photomultiplier tube was used as a detector at a total flow rate of 4.94 ml/min. Perphenazine was determined by a linear calibration plot of the following equation in the range 50-350 ppm: mV=-4.488+0.1162C, with a correlation coefficient of 0.9989 for five measurements and a relative standard deviation less than 2.33. A sampling frequency not less than 110 samples h(-1) was established. Three factors namely, the flow rate, sulphuric acid and permanganate concentrations were found to have an influence on the amount of chemiluminescence intensity produced. Therefore, their interaction effects were thoroughly investigated by employing the 2(3) factorial design chemometrical approach and the results obtained revealed a higher interaction between sulphuric acid and permanganate and a less significant interaction for both reagents with the flow rate. The interaction of variables observed necessitated the conduct of the super modified simplex optimization procedure which has resulted in offering the proper optimum conditions as stated above and led to the quantitative assay of perphenazine. An interference study indicated that the method was suitable for application in pharmaceutical preparations.

  13. A miniaturized liquid core waveguide-capillary electrophoresis system with flow injection sample introduction and fluorometric detection using light-emitting diodes.

    Science.gov (United States)

    Wang, S L; Huang, X J; Fang, Z L

    2001-09-15

    A novel miniaturized capillary electrophoresis (CE) system is described where a Teflon AF-coated silica capillary serves both as the separation channel and as a transversely illuminated liquid core waveguide. This device uniquely uses flow injection (FI)-based split-flow sample introduction through a falling-drop interface. An H-channel structure fixed on a microscope glass slide utilizes a horizontal separation capillary with tubular sidearms on each end that serve as inlet and outlet flow-through electrode reservoirs. The inlet reservoir also functions as a falling-drop interface for coupling to the FI system. A blue LED is used as excitation source. A large-core optical fiber takes the emitted fluorescence to an inexpensive PMT with two layers of green plastic used for optical filtering. No focusing arrangement is needed. Continuous FI introduction of a series of 30-microL samples containing a mixture of of fluorescein isothiocyanate (FITC)-labeled amino acids allowed a throughput rate up to 144 samples/ h, with approximately 2% carryover and good precision (3.2% RSD). Baseline separation was achieved for FITC-labeled arginine, phenylalanine, glycine, and FITC in sodium tetraborate buffer (pH 9.5) with plate heights of 5.4-5.5 microm and plate numbers of 2.34 x 10(4)-2.37 x 10(4) under electrical field strengths of 214 V/cm for injection and 500 V/cm for separation (14-cm capillary, 48-microm i.d.). Detection limits (S/N = 3) were 1.3 microM for arginine and 1.9 microM for phenylalanine and glycine.

  14. Monitoring Lipase/Esterase Activity by Stopped Flow in a Sequential Injection Analysis System Using p-Nitrophenyl Butyrate

    Directory of Open Access Journals (Sweden)

    Jorge Pliego

    2015-01-01

    Full Text Available Lipases and esterases are biocatalysts used at the laboratory and industrial level. To obtain the maximum yield in a bioprocess, it is important to measure key variables, such as enzymatic activity. The conventional method for monitoring hydrolytic activity is to take out a sample from the bioreactor to be analyzed off-line at the laboratory. The disadvantage of this approach is the long time required to recover the information from the process, hindering the possibility to develop control systems. New strategies to monitor lipase/esterase activity are necessary. In this context and in the first approach, we proposed a lab-made sequential injection analysis system to analyze off-line samples from shake flasks. Lipase/esterase activity was determined using p-nitrophenyl butyrate as the substrate. The sequential injection analysis allowed us to measure the hydrolytic activity from a sample without dilution in a linear range from 0.05–1.60 U/mL, with the capability to reach sample dilutions up to 1000 times, a sampling frequency of five samples/h, with a kinetic reaction of 5 min and a relative standard deviation of 8.75%. The results are promising to monitor lipase/esterase activity in real time, in which optimization and control strategies can be designed.

  15. The Influence of Uniform Suction/Injection on Heat Transfer of MHD Hiemenz Flow in Porous Media

    DEFF Research Database (Denmark)

    Ghsemi, E; Soleimani, S; Barari, Amin

    2012-01-01

    The steady two-dimensional laminar forced magneto-hydrodynamic (MHD) Hiemenz flow against a flat plate with variable wall temperature in a porous medium is analyzed. The transformed nonlinear boundary-layer equations are solved analytically by homotopy analysis method (HAM). Results for the veloc...

  16. Regional cerebral blod flow studied by xenon-133. Intra-arterial injection studies and inhalation studies using emission tomography

    DEFF Research Database (Denmark)

    Lassen, N A

    1980-01-01

    .) technique is insensitive both to hyperemia and ischemia yielding essentially only a mean flow value. A new rapidly moving single photon tomograph following D. Kuhl's principle is presented applicable to Xe-133. Preliminary clinical data show that this technique is able to detect ischemic areas both with Xe...

  17. Multipoint Fuel Injection Arrangements

    Science.gov (United States)

    Prociw, Lev Alexander (Inventor)

    2017-01-01

    A multipoint fuel injection system includes a plurality of fuel manifolds. Each manifold is in fluid communication with a plurality of injectors arranged circumferentially about a longitudinal axis for multipoint fuel injection. The injectors of separate respective manifolds are spaced radially apart from one another for separate radial staging of fuel flow to each respective manifold.

  18. Automated Analysis of Clozapine and Norclozapine in Human Plasma Using Novel Extraction Plate Technology and Flow-Injection Tandem Mass Spectrometry.

    Science.gov (United States)

    Couchman, Lewis; Subramaniam, Krithika; Fisher, Danielle S; Belsey, Sarah L; Handley, Simon A; Flanagan, Robert J

    2016-02-01

    Analysis of plasma clozapine and N-desmethylclozapine (norclozapine) for therapeutic drug monitoring purposes is well established. To minimize analysis times and facilitate rapid reporting of results, we have fully automated sample preparation using novel AC Extraction Plates and a Tecan Freedom EVO 100 liquid handling platform, and minimized extract analysis times using flow-injection tandem mass spectrometry (FIA-MS/MS). Analytes and deuterium-labeled internal standards were extracted from plasma (100 μL) at pH 10.6 and extracts analyzed directly using tandem mass spectrometry [20 μL injection, 0.7 mL/min methanol carrier flow, analysis time (injection-to-injection) approximately 60 seconds]. Validation data showed excellent intraplate and interplate accuracy (95%-104% nominal concentrations). Interbatch precision (% RSD) at the limit of quantitation (0.01 mg/L) was 3.5% and 5.5% for clozapine and norclozapine, respectively. Matrix effects were observed for both clozapine and norclozapine, but were compensated for by the internal standards. Overall process efficiency was 56%-70% and 66%-77% for clozapine and norclozapine, respectively. Mean relative process efficiency was 98% and 99% for clozapine and norclozapine, respectively. Comparison of results from patient samples (n = 81) analyzed using (1) manual liquid-liquid extraction with liquid chromatography-tandem mass spectrometry (LC-MS/MS) and (2) automated extraction with FIA-MS/MS gave y = 1.01x - 0.002, R(2) = 0.9943 and y = 1.01x + 0.009, R(2) = 0.9957 for clozapine and norclozapine, respectively. Bland-Altman plots revealed a [mean (95% limits of agreement) bias of 0.0074 (-0.04 to 0.06) mg/L and of 0.015 (-0.02 to 0.05) mg/L for clozapine and norclozapine, respectively]. FIA-MS/MS used with automated extraction offers a rapid, simple, cost-effective alternative to manual liquid-liquid extraction and conventional LC analysis for clozapine therapeutic drug monitoring.

  19. Double injection/single detection asymmetric flow injection manifold for spectrophotometric determination of ascorbic acid and uric acid: Selection the optimal conditions by MCDM approach based on different criteria weighting methods

    Science.gov (United States)

    Boroumand, Samira; Chamjangali, Mansour Arab; Bagherian, Ghadamali

    2017-03-01

    A simple and sensitive double injection/single detector flow injection analysis (FIA) method is proposed for the simultaneous kinetic determination of ascorbic acid (AA) and uric acid (UA). This method is based upon the difference between the rates of the AA and UA reactions with Fe3 + in the presence of 1, 10-phenanthroline (phen). The absorbance of Fe2 +/1, 10-phenanthroline (Fe-phen) complex obtained as the product was measured spectrophotometrically at 510 nm. To reach a good accuracy in the differential kinetic determination via the mathematical manipulations of the transient signals, different criteria were considered in the selection of the optimum conditions. The multi criteria decision making (MCDM) approach was applied for the selection of the optimum conditions. The importance weights of the evaluation criteria were determined using the analytic hierarchy process, entropy method, and compromised weighting (CW). The experimental conditions (alternatives) were ranked by the technique for order preference by similarity to an ideal solution. Under the selected optimum conditions, the obtained analytical signals were linear in the ranges of 0.50-5.00 and 0.50-4.00 mg L- 1 for AA and UA, respectively. The 3σ detection limits were 0.07 mg L- 1 for AA and 0.12 mg L- 1 for UA. The relative standard deviations for four replicate determinations of AA and UA were 2.03% and 3.30% respectively. The method was also applied for the analysis of analytes in the blood serum, Vitamine C tablets, and tap water with satisfactory results.

  20. On-line solid-phase extraction and multisyringe flow injection analysis of Al(III) and Fe(III) in drinking water.

    Science.gov (United States)

    Vanloot, Pierre; Branger, Catherine; Margaillan, André; Brach-Papa, Christophe; Boudenne, Jean-Luc; Coulomb, Bruno

    2007-11-01

    A new analytical method was developed for on-line monitoring of residual coagulants (aluminium and iron salts) in potable water. The determination was based on a sequential procedure coupling an extraction/enrichment step of the analytes onto a modified resin and a spectrophotometric measurement of a surfactant-sensitized binary complex formed between eluted analytes and Chrome Azurol S. The optimization of the solid phase extraction was performed using factorial design and a Doehlert matrix considering six variables: sample percolation rate, sample metal concentration, flow-through sample volume (all three directly linked to the extraction step), elution flow rate, concentration and volume of eluent (all three directly linked to the elution step). A specific reagent was elaborated for sensitive and specific spectrophotometric determination of Al(III) and Fe(III), by optimizing surfactant and ligand concentrations and buffer composition. The whole procedure was automated by a multisyringe flow injection analysis (MSFIA) system. Detection limits of 4.9 and 5.6 microg L(-1) were obtained for Al(III) and Fe(III) determination , respectively, and the linear calibration graph up to 300 microg L(-1) (both for Al(III) and Fe(III)) was well adapted to the monitoring of drinking water quality. The system was successfully applied to the on-site determination of Al(III) and Fe(III) at the outlet of two water treatment units during two periods of the year (winter and summer conditions).

  1. Nonaqueous catalytic fluorometric trace determination of vanadium based on the pyronine B-hydrogen peroxide reaction and flow injection after cloud point extraction.

    Science.gov (United States)

    Paleologos, E K; Koupparis, M A; Karayannis, M I; Veltsistas, P G

    2001-09-15

    The catalytic effect of vanadium on the pyronine B-H2O2 system is examined. Enhancement of the catalytic reaction rate along with the efficiency and selectivity against vanadium is achieved in a formic acid environment in the presence of a nonionic surfactant (Triton X-114). Elimination of drastic interference caused by inorganic acids and aqueous matrix along with a 50-fold preconcentration of vanadium are facilitated through cloud point extraction of its neutral complex with 8-quinolinol in an acidic solution. Subsequent flow injection analysis (FIA) with fluorometric detection renders the proposed method ideal for selective and cost-effective determination of as little as 0.020 microng L(-1) vanadium in environmental, biological, and food substrates. The preconcentration step can be applied simultaneously to multiple samples, allowing for massive preparation prior to analysis, compensating, thus, for the time-consuming procedure.

  2. Determination of formaldehyde in frozen fish with formaldehyde dehydrogenase using a flow injection system with an incorporated gel-filtration chromatrography column

    DEFF Research Database (Denmark)

    Bechmann, Iben Ell

    1996-01-01

    A flow injection analysis (FIA) system for determination of formaldehyde in frozen fish products is described. The system provides a rapid and selective determination of formaldehyde in aqueous fish extracts by the combination of a deproteinization procedure and a stopped-now enzymatic approach...... in a FIA system. The FIA system is furnished with a gel-filtration chromatography column for on-line removal of the proteins from the extract before the enzymatic analysis is performed. Compared with the standard methods for determination of formaldehyde in fish products the present method is much faster...... and less affected by interferences. The limit of detection for the proposed method is 2.5 mg/l of formaldehyde. The sampling frequency is about 10 determinations per hour....

  3. Fast microwave-assisted free sugars washing and hydrolysis pre-treatment for the flow injection determination of starch in food.

    Science.gov (United States)

    Caballo-López, A; Luque de Castro, M D

    2003-03-10

    The approach used consists of a flow injection (FI) manifold assisted by a focused microwave digestor for both fast washing of free sugars and acceleration of the hydrolysis step prior to the determination of starch in food. The action of microwaves reduces both the times for removal of free sugars to a 5 min single washing cycle with ethanol/water and that of the subsequent starch hydrolysis to a 10 min step. The sugars formed in the starch hydrolysis are in-line derivatised and photometrically monitored at lambda=460 nm. In this way, automation of pre-treatment and determination is achieved with the minimum of both cost and time. The precision of the overall method, expressed as relative standard deviation, is 3.75% and the total analysis time is 38 min. Comparison of the results, obtained in applying the method to flour and bread, is in agreement with those provided by the manual method.

  4. Differentiation of the four major species of cinnamons (C. burmannii, C. verum, C. cassia, and C. loureiroi) using a flow injection mass spectrometric (FIMS) fingerprinting method.

    Science.gov (United States)

    Chen, Pei; Sun, Jianghao; Ford, Paul

    2014-03-26

    A simple and efficient flow injection mass spectrometric (FIMS) method was developed to differentiate cinnamon (Cinnamomum) bark (CB) samples of the four major species (C. burmannii, C. verum, C. aromaticum, and C. loureiroi) of cinnamon. Fifty cinnamon samples collected from China, Vietnam, Indonesia, and Sri Lanka were studied using the developed FIMS fingerprinting method. The FIMS fingerprints of the cinnamon samples were analyzed using principal component analysis (PCA). The FIMS technique required only 1 min of analysis time per sample. The representative samples from each of the four major species of cinnamon were further examined using an ultrahigh-performance liquid chromatography-high-resolution mass spectrometry system, and the chemical differences between the four species were profiled. The results showed that the 1 min FIMS fingerprinting method successfully differentiated the four cinnamon species studied.

  5. Flow injection mass spectral fingerprints demonstrate chemical differences in Rio Red grapefruit with respect to year, harvest time, and conventional versus organic farming.

    Science.gov (United States)

    Chen, Pei; Harnly, James M; Lester, Gene E

    2010-04-28

    Spectral fingerprints were acquired for Rio Red grapefruit using flow injection electrospray ionization with ion trap and time-of-flight mass spectrometry (FI-ESI-IT-MS and FI-ESI-TOF-MS). Rio Red grapefruits were harvested 3 times a year (early, mid, and late harvests) in 2005 and 2006 from conventionally and organically grown trees. Data analysis using analysis of variance principal component analysis (ANOVA-PCA) demonstrated that, for both MS systems, the chemical patterns were different as a function of farming mode (conventional vs organic), as well as growing year and time of harvest. This was visually obvious with PCA and was shown to be statistically significant using ANOVA. The spectral fingerprints provided a more inclusive view of the chemical composition of the grapefruit and extended previous conclusions regarding the chemical differences between conventionally and organically grown Rio Red grapefruit.

  6. Cloud point extraction of vanadium in parenteral solutions using a nonionic surfactant (PONPE 5.0) and determination by flow injection-inductively coupled plasma optical emission spectrometry.

    Science.gov (United States)

    Wuilloud, Gustavo M; de Wuilloud, Jorgelina C A; Wuilloud, Rodolfo G; Silva, Maria F; Olsina, Roberto A; Martinez, Luis D

    2002-10-16

    A preconcentration and determination methodology for vanadium at trace levels in parenteral solutions was developed. Cloud point extraction was successfully employed for the preconcentration of vanadium prior to inductively coupled plasma atomic optical emission spectrometry (ICP-OES) coupled to a flow injection (FI) system. The vanadium was extracted as vanadium-2-(5-bromo-2-pyridylazo)-5-diethylaminophenol [V-(5-Br-PADAP)] complex, at pH 3.7 mediated by micelles of the nonionic surfactant polyoxyethylene (5.0) nonylphenol (PONPE 5.0). The extracted surfactant-rich phase (100 mul) was mixed with 100 mul of ethanol and this final volume injected into ICP-OES for the vanadium determination. Under these conditions, the 50 ml sample solution preconcentration allowed raising an enrichment factor of 250-fold; however, it was possible to obtain a theoretical enrichment factor of 500-fold. The lower limit of detection (LOD) obtained under the optimal conditions was 16 ng l(-1). The precision for 10 replicate determinations at the 2.0 mug l(-1) V level was 2.3% relative standard deviation (RSD), calculated with the peak heights. The calibration graph using the preconcentration system for vanadium was linear with a correlation coefficient of 0.9996 at levels near the detection limits up to at least 50 mug l(-1). The method was successfully applied to the determination of vanadium in parenteral solution samples.

  7. Immobilized stearic acid as a new sorbent for on-line preconcentration and determination of lead by flow injection flame atomic absorption spectrometry

    Directory of Open Access Journals (Sweden)

    Dadfarnia Shayessteh

    2006-01-01

    Full Text Available The present study examines the possibility of immobilization of stearic acid on microcrystalline naphthalene for preparation of microcolumn and evaluation of its potential for adsorption and preconcentration of trace amounts of metal ions. It was found that this sorbent has high affinity for lead. Consequently, a rapid on-line preconcentration technique for the determination of lead by Flow Injection Flame Atomic Absorption Spectrometry had been devised. Preconcentration was based on accumulation of analyte on immobilized stearic acid microcolumn and subsequent elution by injection of a small volume of nitric acid (250 µL of 1 mol L-1. A sample volume of 20 mL resulted in a preconcentration factor of 84, and relative standard deviations for solutions containing 40 and 200 µg L-1 were 5.1 and 1.2%, respectively. The procedure was applied to tap water, river water, sea water, apple juice, beet leaf, urine, and certified stainless steel. The accuracy was proved by performing recovery experiments, Graphite Furnace Atomic Absorption Spectrometry measurements, and analysis of a stainless steel certified reference material.

  8. CuO nanosheets-enhanced flow-injection chemiluminescence system for determination of vancomycin in water, pharmaceutical and human serum

    Science.gov (United States)

    Khataee, A. R.; Hasanzadeh, A.; Iranifam, M.; Fathinia, M.; Hanifehpour, Y.; Joo, S. W.

    2014-03-01

    A novel, rapid and sensitive CuO nanosheets (NSs) amplified flow-injection chemiluminescence (CL) system, luminol-H2O2-CuO nanosheets, was developed for determination of the vancomycin hydrochloride for the first time. It was found that vancomycin could efficiently inhibit the CL intensity of luminol-H2O2-CuO nanosheets system in alkaline medium. Under the optimum conditions, the inhibited CL intensity was linearly proportional to the concentration of vancomycin over the ranges of 0.5-18.0 and 18.0-40.0 mg L-1, with a detection limit (3σ) of 0.1 mg L-1. The precision was calculated by analyzing samples containing 5.0 mg L-1 vancomycin (n = 11) and the relative standard deviation (RSD) was 2.8%. Also, a high injection throughput of 120 sample h-1 was obtained. The CuO nanosheets were synthesized by a sonochemical method. Also, X-ray diffraction (XRD) and scanning electron microscopy (SEM) analyses were employed to characterize the CuO nanosheets. The method was successfully employed to determine vancomycin hydrochloride in environmental water samples, pharmaceutical formulation and spiked human serum.

  9. Determination of As, Hg and Pb in herbs using slurry sampling flow injection chemical vapor generation inductively coupled plasma mass spectrometry.

    Science.gov (United States)

    Tai, Chia-Yi; Jiang, Shiuh-Jen; Sahayam, A C

    2016-02-01

    Analysis of herbs for As, Hg and Pb has been carried out using slurry sampling inductively coupled plasma mass spectrometry (ICP-MS) with flow injection vapor generation. Slurry containing 0.5% m/v herbal powder, 0.1% m/v citric acid and 2% v/v HCl was injected into the VG-ICP-MS system for the determination of As, Hg and Pb that obviate dissolution and mineralization. Standard addition and isotope dilution methods were used for quantifications in selected herbal powders. This method has been validated by the determination of As, Hg and Pb in NIST standard reference materials SRM 1547 Peach Leaves and SRM 1573a Tomato Leaves. The As, Hg and Pb analysis results of the reference materials agreed with the certified values. The precision obtained by the reported procedure was better than 7% for all determinations. The detection limit estimated from standard addition curve was 0.008, 0.003, and 0.007 ng mL(-1) for As, Hg and Pb, respectively. Copyright © 2015 Elsevier Ltd. All rights reserved.

  10. Group solution for an unsteady non-Newtonian Hiemenz flow with variable fluid properties and suction/injection

    Science.gov (United States)

    M. El-Hawary, H.; Mostafa, A. A. Mahmoud; Reda, G. Abdel-Rahman; Abeer, S. Elfeshawey

    2014-09-01

    The theoretic transformation group approach is applied to address the problem of unsteady boundary layer flow of a non-Newtonian fluid near a stagnation point with variable viscosity and thermal conductivity. The application of a two-parameter group method reduces the number of independent variables by two, and consequently the governing partial differential equations with the boundary conditions transformed into a system of ordinary differential equations with the appropriate corresponding conditions. Two systems of ordinary differential equations have been solved numerically using a fourth-order Runge—Kutta algorithm with a shooting technique. The effects of various parameters governing the problem are investigated.

  11. Adalimumab Injection

    Science.gov (United States)

    Humira® Injection ... Adalimumab injection is used alone or with other medications to relieve the symptoms of certain autoimmune disorders (conditions in ... some areas of the body) in adults. Adalimumab injection is in a class of medications called tumor ...

  12. Oxacillin Injection

    Science.gov (United States)

    Oxacillin injection is used to treat infections caused by certain bacteria. Oxacillin injection is in a class of medications called penicillins. ... works by killing bacteria.Antibiotics such as oxacillin injection will not work for colds, flu, or other ...

  13. Rituximab Injection

    Science.gov (United States)

    Rituximab injection (Rituxan) and rituximab and hyaluronidase human injection (Rituxin Hycela) are used alone or with other medications to ... that begins in the white blood cells). Rituximab injection is also used with another medication to treat ...

  14. Fluorouracil Injection

    Science.gov (United States)

    Adrucil® Injection ... Fluorouracil injection comes as a solution (liquid) to be given intravenously (into a vein) by a doctor or nurse ... you are feeling during your treatment with fluorouracil injection.

  15. Ondansetron Injection

    Science.gov (United States)

    Zofran® Injection ... Ondansetron injection is used to prevent nausea and vomiting caused by cancer chemotherapy and surgery. Ondansetron is in a ... medications: or any of the ingredients in ondansetron injection. Ask your pharmacist for a list of the ...

  16. Romiplostim Injection

    Science.gov (United States)

    ... or may tell you to stop taking these medications if romiplostim injection works well for you.Romiplostim injection does not ... will give you the manufacturer's patient information sheet (Medication ... romiplostim injection. Read the information carefully and ask your doctor ...

  17. Flow injection small-volume fiber-optic pH sensor based on evanescent wave excitation and fluorescence determination.

    Science.gov (United States)

    Xiong, Yan; Huang, Ying; Ye, Zhongbin; Guan, Yafeng

    2011-05-01

    A small-volume fiber-optic pH sensor (FOEWS) based on evanescent wave excitation is developed and evaluated. The sensor is simply fabricated by inserting a decladded optical fiber into a transparent capillary tube. A microchannel between the optical fiber and the capillary inner wall was formed and acted as flow cell for solution flowing through. The pH-sensitive fluorophore of fluorescein can be excited by the evanescent wave field produced on the fiber core surface to produce emission fluorescence. pH value was then sensed by its enhancing effect on the emission fluorescence intensity. The response range of the sensor is from pH 2.09 to pH 8.85 and the linear range is from pH 3.25 to 8.85. The proposed sensor has a small detection volume of 2.5 μL and a short response time of 8 s. It has been applied to measure pH values of real water samples and was in good agreement with the results obtained by commercial pH meter. © Springer Science+Business Media, LLC 2010

  18. Viruses exploiting peroxisomes.

    Science.gov (United States)

    Lazarow, Paul B

    2011-08-01

    Viruses that are of great importance for global public health, including HIV, influenza and rotavirus, appear to exploit a remarkable organelle, the peroxisome, during intracellular replication in human cells. Peroxisomes are sites of lipid biosynthesis and catabolism, reactive oxygen metabolism, and other metabolic pathways. Viral proteins are targeted to peroxisomes (the spike protein of rotavirus) or interact with peroxisomal proteins (HIV's Nef and influenza's NS1) or use the peroxisomal membrane for RNA replication. The Nef interaction correlates strongly with the crucial Nef function of CD4 downregulation. Viral exploitation of peroxisomal lipid metabolism appears likely. Mostly, functional significance and mechanisms remain to be elucidated. Recently, peroxisomes were discovered to play a crucial role in the innate immune response by signaling the presence of intracellular virus, leading to the first rapid antiviral response. This review unearths, interprets and connects old data, in the hopes of stimulating new and promising research. Copyright © 2011. Published by Elsevier Ltd.

  19. Dissemination and Exploitation Strategy

    DEFF Research Database (Denmark)

    Badger, Merete; Monaco, Lucio; Fransson, Torsten

    The research infrastructure project Virtual Campus Hub (VCH) runs from October 1, 2011 to September 30, 2013. Four technical universities in Europe, who are all active in the field of sustainable energy, form the project consortium: the Technical University of Denmark, The Royal Institute...... of Technology in Sweden, Politecnico di Torino in Italy, and Eindhoven University of Technology in the Netherlands. The project is partially funded by the European Commission under the 7th Framework Programme (project no. RI-283746). This report describes the final dissemination and exploitation strategy...... for project Virtual Campus Hub. A preliminary dissemination and exploitation plan was setup early in the project as described in the deliverable D6.1 Dissemination strategy paper - preliminary version. The plan has been revised on a monthly basis during the project’s lifecycle in connection with the virtual...

  20. Construction of power flow feasibility sets

    OpenAIRE

    Dvijotham, Krishnamurthy; Turitsyn, Konstantin

    2015-01-01

    We develop a new approach for construction of convex analytically simple regions where the AC power flow equations are guaranteed to have a feasible solutions. Construction of these regions is based on efficient semidefinite programming techniques accelerated via sparsity exploiting algorithms. Resulting regions have a simple geometric shape in the space of power injections (polytope or ellipsoid) and can be efficiently used for assessment of system security in the presence of uncertainty. Ef...

  1. Modular ultrahigh vacuum-compatible gas-injection system with an adjustable gas flow for focused particle beam-induced deposition

    Energy Technology Data Exchange (ETDEWEB)

    Klingenberger, D.; Huth, M. [Physikalisches Institut, Goethe University, 60438 Frankfurt am Main (Germany)

    2009-09-15

    A gas-injection system (GIS) heats up a powdery substance and transports the resulting gas through a capillary into a vacuum chamber. Such a system can be used to guide a (metal)organic precursor gas very close to the focal area of an electron or ion beam, where a permanent deposit is created and adheres to the substrate. This process is known as focused particle beam-induced deposition. The authors present design principles and give construction details of a GIS suitable for ultrahigh vacuum usage. The GIS is composed of several self-contained components which can be customized rather independently. It allows for a continuously adjustable gas-flow rate. The GIS was attached to a standard scanning electron microscope (JEOL 6100) and tested with the tungsten precursor W(CO){sub 6}. The analysis of the deposits by means of atomic force microscopy and energy dispersive x-ray spectroscopy provides clear evidence that excellent gas-flow-rate stability and ensuing growth rate and metal-content reproducibility are experienced.

  2. Field sample preconcentration of copper in sea water using chelating minicolumns subsequently incorporated on a flow-injection-flame atomic absorption spectrometry system.

    Science.gov (United States)

    Yebra, M C; Carro, N; Enríquez, M F; Moreno-Cid, A; García, A

    2001-06-01

    A field flow preconcentration system for copper determination in seawater is described. Seawater samples are collected and preconcentrated in situ by passing them using a peristaltic pump through a minicolumn packed with Amberlite XAD-4 impregnated with the complexing agent 1-(2-pyridylazo)-2-naphthol. Thus, copper is preconcentrated without the interference of the saline matrix. Once in the laboratory, the minicolumns loaded with copper are incorporated on a flow injection system and eluted with a small volume of a 20% (v/v) ethanolic solution of 0.5 mol L-1 hydrochloric acid into the nebuliser-burner system of a flame atomic absorption spectrometer. The analytical figures of merit for the determination of copper are as follows: detection limit (3s), 0.06 microgram L-1; precision (RSD), 1.2% for 2 micrograms L-1; enrichment factor, 30 (using 25 mL of sample and 83 microL of eluent). Analysis of certified reference materials (SLEW-3 and NASS-5) showed good agreement with the certified value. This procedure was applied to the determination of copper in seawater samples from Galicia (Spain).

  3. An automated flow injection system for metal determination by flame atomic absorption spectrometry involving on-line fabric disk sorptive extraction technique.

    Science.gov (United States)

    Anthemidis, A; Kazantzi, V; Samanidou, V; Kabir, A; Furton, K G

    2016-08-15

    A novel flow injection-fabric disk sorptive extraction (FI-FDSE) system was developed for automated determination of trace metals. The platform was based on a minicolumn packed with sol-gel coated fabric media in the form of disks, incorporated into an on-line solid-phase extraction system, coupled with flame atomic absorption spectrometry (FAAS). This configuration provides minor backpressure, resulting in high loading flow rates and shorter analytical cycles. The potentials of this technique were demonstrated for trace lead and cadmium determination in environmental water samples. The applicability of different sol-gel coated FPSE media was investigated. The on-line formed complex of metal with ammonium pyrrolidine dithiocarbamate (APDC) was retained onto the fabric surface and methyl isobutyl ketone (MIBK) was used to elute the analytes prior to atomization. For 90s preconcentration time, enrichment factors of 140 and 38 and detection limits (3σ) of 1.8 and 0.4μgL(-1) were achieved for lead and cadmium determination, respectively, with a sampling frequency of 30h(-1). The accuracy of the proposed method was estimated by analyzing standard reference materials and spiked water samples. Copyright © 2016 Elsevier B.V. All rights reserved.

  4. Flow-injection chemiluminescence determination of cloxacillin in water samples and pharmaceutical preparation by using CuO nanosheets-enhanced luminol-hydrogen peroxide system

    Science.gov (United States)

    Khataee, Alireza; Iranifam, Mortaza; Fathinia, Mehrangiz; Nikravesh, Mina

    2015-01-01

    In this paper, a rapid and sensitive flow-injection chemiluminescence (flow-CL) system was developed for the determination of cloxacillin sodium in environmental water samples and pharmaceutical preparations. The method was based on the enhancement effect of cloxacillin sodium on the CL reaction of luminal-H2O2-CuO nanosheets (NSs) in alkaline medium. The CuO nanosheets were synthesized using a green sonochemical method. The physical properties of the synthesized CuO nanosheets were characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM) analyses. The influences of various experimental factors such as H2O2, NaOH, luminol and CuO nanosheets concentrations were investigated. Under the optimum conditions, the enhanced CL intensity was linearly related to the concentration of cloxacillin sodium in the range of the 0.05-30.00 mg L-1 with a correlation coefficient of 0.995. The corresponding detection limit (3σ) was calculated to be 0.026 mg L-1. The relative standard deviation (RSD) of the developed method was 2.21% with 11 repeated measurements of 4.00 mg L-1 cloxacillin sodium. Also, a total analysis time per sample was 30 s which confirmed the rapidity of the proposed method. The analytical applicability of the proposed CL system was assessed by determining cloxacillin sodium in spiked environmental water samples and pharmaceutical preparation. Furthermore, the possible mechanism of CL reaction was discussed.

  5. Preparation of Carbon-Doped TiO2 Nanopowder Synthesized by Droplet Injection of Solution Precursor in a DC-RF Hybrid Plasma Flow System

    Science.gov (United States)

    Jang, Juyong; Takana, Hidemasa; Ando, Yasutaka; Solonenko, Oleg P.; Nishiyama, Hideya

    2013-08-01

    Carbon-doped titanium dioxide nanopowder has received much attention because of its higher photocatalytic performance, which is practically activated not only by UV, but also by visible light irradiation. In the present study, C-TiO2 nanopowder was synthesized by droplet injection of solution precursor in a DC-RF hybrid plasma flow system, resulting in higher photocatalytic performance even under visible light irradiation. In-flight C-TiO2 nanoparticles reacted with the high concentration of carbon in plasma flow and were then deposited on the surfaces of two quartz tubes in the upstream and downstream regions of this system. The collected C-TiO2 nanopowder contained anatase-rutile mixed-phase TiO2 and TiC, the contents of which depended on the location of the powder collection, the temperature, and the duration of plasma treatment. Highly functional C-TiO2 nanopowder collected in the downstream region exhibited a higher degradation rate of methylene blue than that of single-phase anatase TiO2, even under visible light irradiation, in spite of being TiC.

  6. Determination of L-cysteine in amino acid mixture and human urine by flow-injection analysis with a biamperometric detector.

    Science.gov (United States)

    Zhao, C; Zhang, J; Song, J

    2001-10-15

    Based on the electrocatalytic oxidation of cysteine at pretreated platinum electrode and the flow-injection biamperometry for irreversible couple, a novel electrochemical detector is proposed for the selective determination of cysteine in amino acid mixtures and human urine samples. A thin-layer flow through cell was used to achieve large electrode surface area to volume ratio. Two identical pretreated platinum electrodes were mounted in the cell with an applied potential difference of 10 mV. By coupling two independent and irreversible electrode processes, namely, the oxidation of cysteine and the reduction of platinum oxide, the biamperometric detection scheme has been established. The resulting current is linear to cysteine over the range 4 x 10(-7)-4 x 10(-5) M with the detection limit 1 x 10(-7) M (15 pmol). The selectivity of the detector is tested by 55 foreign species including 26 ions, 11 amino acids, 6 vitamins, and 12 other compounds possibly found in urine. The detector performs well as a routine assay, showing high efficiency (180 samples/h) and good reproductivity shown by a RSD of 0.6% for eight repeated determinations of 2 x 10(-6) M cysteine. The urine samples are detected directly without the need of pretreatment or adding other reagents. Copyright 2001 Academic Press.

  7. On-line solid-phase extraction and multisyringe flow injection analysis of Al(III) and Fe(III) in drinking water

    Energy Technology Data Exchange (ETDEWEB)

    Vanloot, Pierre; Boudenne, Jean-Luc; Coulomb, Bruno [Universite de Provence - Case 29, Laboratoire de Chimie et Environnement (FRE 2704), Marseille cedex 3 (France); Branger, Catherine; Margaillan, Andre [ISITV - Universite du Sud Toulon Var, Laboratoire de Chimie Appliquee MFS (EA 1356), La Garde du Var (France); Brach-Papa, Christophe [European Commission, Joint Research Centre, Institute for Reference Materials and Measurements, Isotope Measurements Unit, Geel (Belgium)

    2007-11-15

    A new analytical method was developed for on-line monitoring of residual coagulants (aluminium and iron salts) in potable water. The determination was based on a sequential procedure coupling an extraction/enrichment step of the analytes onto a modified resin and a spectrophotometric measurement of a surfactant-sensitized binary complex formed between eluted analytes and Chrome Azurol S. The optimization of the solid phase extraction was performed using factorial design and a Doehlert matrix considering six variables: sample percolation rate, sample metal concentration, flow-through sample volume (all three directly linked to the extraction step), elution flow rate, concentration and volume of eluent (all three directly linked to the elution step). A specific reagent was elaborated for sensitive and specific spectrophotometric determination of Al(III) and Fe(III), by optimizing surfactant and ligand concentrations and buffer composition. The whole procedure was automated by a multisyringe flow injection analysis (MSFIA) system. Detection limits of 4.9 and 5.6 {mu}g L{sup -1} were obtained for Al(III) and Fe(III) determination, respectively, and the linear calibration graph up to 300 {mu}g L{sup -1} (both for Al(III) and Fe(III)) was well adapted to the monitoring of drinking water quality. The system was successfully applied to the on-site determination of Al(III) and Fe(III) at the outlet of two water treatment units during two periods of the year (winter and summer conditions). (orig.)

  8. Hacking the art of exploitation

    CERN Document Server

    Erickson, Jon

    2003-01-01

    A comprehensive introduction to the techniques of exploitation and creative problem-solving methods commonly referred to as "hacking," Hacking: The Art of Exploitation is for both technical and non-technical people who are interested in computer security. It shows how hackers exploit programs and write exploits, instead of just how to run other people's exploits. Unlike many so-called hacking books, this book explains the technical aspects of hacking, including stack based overflows, heap based overflows, string exploits, return-into-libc, shellcode, and cryptographic attacks on 802.11b.

  9. Ibandronate Injection

    Science.gov (United States)

    Boniva® Injection ... Ibandronate injection is used to treat osteoporosis (a condition in which the bones become thin and weak and break ... Ibandronate injection comes as a solution (liquid) to be injected into a vein by a doctor or nurse in ...

  10. Tocilizumab Injection

    Science.gov (United States)

    ... or the syringe and do not inject the medication.You may inject tocilizumab injection on the front of the thighs or anywhere ... your doctor about the risks of receiving this medication.Tocilizumab injection may cause other side effects. Call your doctor ...

  11. Certolizumab Injection

    Science.gov (United States)

    ... package or the syringe. Do not inject the medication.You may inject certolizumab injection anywhere on your stomach or thighs except your ... your doctor about the risks of receiving this medication.Certolizumab injection may cause other side effects. Call your doctor ...

  12. Sarilumab Injection

    Science.gov (United States)

    ... for RA or who could not take these medications. Sarilumab injection is in a class of medications called interleukin- ... are any problems and do not inject the medication.You may inject sarilumab injection on the front of the thighs or anywhere ...

  13. Hot-wire air flow meter for gasoline fuel-injection system. Calculation of air mass in cylinder during transient condition; Gasoline funsha system yo no netsusenshiki kuki ryuryokei. Kato untenji no cylinder juten kukiryo no keisan

    Energy Technology Data Exchange (ETDEWEB)

    Oyama, Y. [Hitachi Car Engineering, Ltd., Tokyo (Japan); Nishimura, Y.; Osuga, M.; Yamauchi, T. [Hitachi, Ltd., Tokyo (Japan)

    1997-10-01

    Air flow characteristics of hot-wire air flow meters for gasoline fuel-injection systems with supercharging and exhaust gas recycle during transient conditions were investigated to analyze a simple method for calculating air mass in cylinder. It was clarified that the air mass in cylinder could be calculated by compensating for the change of air mass in intake system by using aerodynamic models of intake system. 3 refs., 6 figs., 1 tab.

  14. Convergence analysis of the nonlinear iterative method for two-phase flow in porous media associated with nanoparticle injection

    KAUST Repository

    El-Amin, Mohamed

    2017-08-29

    Purpose In this paper, we introduce modeling, numerical simulation, and convergence analysis of the problem nanoparticles transport carried by a two-phase flow in a porous medium. The model consists of equations of pressure, saturation, nanoparticles concentration, deposited nanoparticles concentration on the pore-walls, and entrapped nanoparticles concentration in pore-throats. Design/methodology/approach Nonlinear iterative IMPES-IMC (IMplicit Pressure Explicit Saturation–IMplicit Concentration) scheme is used to solve the problem under consideration. The governing equations are discretized using the cell-centered finite difference (CCFD) method. The pressure and saturation equations are coupled to calculate the pressure, then the saturation is updated explicitly. Therefore, the equations of nanoparticles concentration, the deposited nanoparticles concentration on the pore walls and the entrapped nanoparticles concentration in pore throats are computed implicitly. Then, the porosity and the permeability variations are updated. Findings We stated and proved three lemmas and one theorem for the convergence of the iterative method under the natural conditions and some continuity and boundedness assumptions. The theorem is proved by induction states that after a number of iterations the sequences of the dependent variables such as saturation and concentrations approach solutions on the next time step. Moreover, two numerical examples are introduced with convergence test in terms of Courant–Friedrichs–Lewy (CFL) condition and a relaxation factor. Dependent variables such as pressure, saturation, concentration, deposited concentrations, porosity and permeability are plotted as contours in graphs, while the error estimations are presented in table for different values of number of time steps, number of iterations and mesh size. Research limitations/implications The domain of the computations is relatively small however, it is straightforward to extend this method

  15. Determination of Diclofenac on a Dysprosium Nanowire- Modified Carbon Paste Electrode Accomplished in a Flow Injection System by Advanced Filtering

    Directory of Open Access Journals (Sweden)

    Ali Akbar Moosavi-Movahedi

    2009-09-01

    Full Text Available A new detection technique called Fast Fourier Transform Square-Wave Voltammetry (FFT SWV is based on measurements of electrode admittance as a function of potential. The response of the detector (microelectrode, which is generated by a redox processes, is fast, which makes the method suitable for most applications involving flowing electrolytes. The carbon paste electrode was modified by nanostructures to improve sensitivity. Synthesized dysprosium nanowires provide a more effective nanotube-like surface [1-4] so they are good candidates for use as a modifier for electrochemical reactions. The redox properties of diclofenac were used for its determination in human serum and urine samples. The support electrolyte that provided a more defined and intense peak current for diclofenac determination was a 0.05 mol L−1 acetate buffer pH = 4.0. The drug presented an irreversible oxidation peak at 850 mV vs. Ag/AgCl on a modified nanowire carbon paste electrode which produced high current and reduced the oxidation potential by about 100 mV. Furthermore, the signal-to-noise ratio was significantly increased by application of a discrete Fast Fourier Transform (FFT method, background subtraction and two-dimensional integration of the electrode response over a selected potential range and time window. To obtain the much sensivity the effective parameters such as frequency, amplitude and pH was optimized. As a result, CDL of 2.0 × 10−9 M and an LOQ of 5.0 × 10−9 M were found for the determination for diclofenac. A good recovery was obtained for assay spiked urine samples and a good quantification of diclofenac was achieved in a commercial formulation.

  16. Cerro Prieto cold water injection: effects on nearby production wells

    Energy Technology Data Exchange (ETDEWEB)

    Truesdell, A.H.; Lippmann, M.J.; De Leon, J.; Rodriguez, M.H.

    1999-07-01

    The liquid-dominated Cerro Prieto geothermal field of northern Baja California, Mexico has been under commercial exploitation since 1973. During the early years of operation, all waste brines were sent to an evaporation pond built west of the production area. In 1989, cooled pond brines began to be successfully injected into the reservoir along the western boundary of the geothermal system. The injection rate varied over the years, and is at present about 20% of the total fluid extracted. As expected under the continental desert conditions prevailing in the area, the temperature and salinity of the pond brines change with the seasons, being higher during the summer and lower during the winter. The chemistry of pond brines is also affected by precipitation of silica, oxidation of H{sub 2}S and reaction with airborne clays. Several production wells in the western part of the field (CP-I area) showed beneficial effects from injection. The chemical (chloride, isotopic) and physical (enthalpy, flow rate) changes observed in producers close to the injectors are reviewed. Some wells showed steam flow increases, in others steam flow decline rates flattened. Because of their higher density, injected brines migrated downward in the reservoir and showed up in deep wells.

  17. Optical fiber reflectance sensor coupled to a multisyringe flow injection system for preconcentration and determination of 1-naphthylamine in water samples.

    Science.gov (United States)

    Guzmán Mar, J L; López Martínez, L; López de Alba, P L; Castrejón Durán, J E; Cerdà Martín, V

    2006-07-28

    A novel optical fiber reflectance sensor is coupled to a multisyringe flow injection system (MSFIA) for the preconcentration and determination of 1-naphthylamine (NPA) in water samples using C18 disks (octadecyl groups). NPA, being a first-class carcinogen, is important from a toxicological point of view and, therefore, its quantification is of considerable interest. In this study, the Griess reaction is used for sensitive and selective spectrophotometric determination of NPA. The reaction involves conversion of nitrite into nitrous acid in acidic medium followed by diazotization of sulphanilic acid and formation of a diazonium salt. The diazonium salt is then combined with NPA to form 4-(sulphophenylazo)-1-naphthylamine, an azo dye. This compound is subsequently retained onto a C18 disk followed by spectrophotometric detection at 540 nm, and it is then eluted with methanol in water (80%, v/v), so that the C18 disk is regenerated for subsequent experiments. Under the established optimum conditions, a calibration graph for NPA was constructed. Good linearity was observed within a concentration range from 10 to 160 microg l(-1). The lineal regression equation is A=(0.0027+/-0.0001) [NPA]+(0.0296+/-0.0047), r=0.9991; relative standard deviation values obtained from the analysis of 10 samples of 10, 80 and 160 microg l(-1) are 4.7, 1.2 and 0.6%, respectively. The mean value relative errors for concentrations of 10, 80, 160 microg l(-1) are 3.4, 0.9 and 0.4%, respectively. The detection and quantification limits were 1.1 and 3.7 microg l(-1). A sampling throughput of 14 injections per hour is achieved. The repeatability calculated for five different C18 disks was E(rel)=2.8%. The proposed technique has been validated by replicate analysis (n=6) of several water samples with spiked NPA, giving satisfactory results.

  18. Slurry sampling flow injection chemical vapor generation inductively coupled plasma mass spectrometry for the determination of trace Ge, As, Cd, Sb, Hg and Bi in cosmetic lotions

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Wei-Ni [Department of Chemistry, National Sun Yat-sen University, Kaohsiung 80424, Taiwan (China); Jiang, Shiuh-Jen, E-mail: sjjiang@faculty.nsysu.edu.tw [Department of Chemistry, National Sun Yat-sen University, Kaohsiung 80424, Taiwan (China); Department of Medical Laboratory Science and Biotechnology, Kaohsiung Medical University, Kaohsiung 80708, Taiwan (China); Chen, Yen-Ling [Department of Fragrance and Cosmetic Science, Kaohsiung Medical University, Kaohsiung 80708, Taiwan (China); Sahayam, A.C. [National Centre for Compositional Characterisation of Materials (CCCM), Hyderabad (India)

    2015-02-20

    Highlights: • Determination of Ge, As, Cd, Sb, Hg and Bi in cosmetic lotions in a single run. • Accurate analysis using isotope dilution and standard addition methods. • Vapor generation ICP-MS yielded superior detection limits compared to ETV-ICP-MS. • No sample dissolution increased sample through put. • Analysis of GBW09305 Cosmetic (Cream) reference material for accuracy. - Abstract: A slurry sampling inductively coupled plasma mass spectrometry (ICP-MS) method has been developed for the determination of Ge, As, Cd, Sb, Hg and Bi in cosmetic lotions using flow injection (FI) vapor generation (VG) as the sample introduction system. A slurry containing 2% m/v lotion, 2% m/v thiourea, 0.05% m/v L-cysteine, 0.5 μg mL{sup −1} Co(II), 0.1% m/v Triton X-100 and 1.2% v/v HCl was injected into a VG-ICP-MS system for the determination of Ge, As, Cd, Sb, Hg and Bi without dissolution and mineralization. Because the sensitivities of the analytes in the slurry and that of aqueous solution were quite different, an isotope dilution method and a standard addition method were used for the determination. This method has been validated by the determination of Ge, As, Cd, Sb, Hg and Bi in GBW09305 Cosmetic (Cream) reference material. The method was also applied for the determination of Ge, As, Cd, Sb, Hg and Bi in three cosmetic lotion samples obtained locally. The analysis results of the reference material agreed with the certified value and/or ETV-ICP-MS results. The detection limit estimated from the standard addition curve was 0.025, 0.1, 0.2, 0.1, 0.15, and 0.03 ng g{sup −1} for Ge, As, Cd, Sb, Hg and Bi, respectively, in original cosmetic lotion sample.

  19. Determination of As(III) and As(V) by Flow Injection-Hydride Generation-Atomic Absorption Spectrometry via On-line Reduction of As(V) by KI

    DEFF Research Database (Denmark)

    Nielsen, Steffen; Hansen, Elo Harald

    1997-01-01

    A volume-based flow injection (FI) procedure is described for the determination and speciation of trace inorganic arsenic, As(III) and As(V), via hydride generation-atomic absorption spectrometry (HG-AAS) of As(III). The determination of total arsenic is obtained by on-line reduction of As(V) to As...

  20. Discrimination of Aurantii Fructus Immaturus and Fructus Poniciri Trifoliatae Immaturus by Flow Injection UV Spectroscopy (FIUV) and 1H NMR using Partial Least-squares Discriminant Analysis (PLS-DA)

    Science.gov (United States)

    Two simple fingerprinting methods, flow-injection UV spectroscopy (FIUV) and 1H nuclear magnetic resonance (NMR), for discrimination of Aurantii FructusImmaturus and Fructus Poniciri TrifoliataeImmaturususing were described. Both methods were combined with partial least-squares discriminant analysis...

  1. Lie-group method for unsteady flows in a semi-infinite expanding or contracting pipe with injection or suction through a porous wall

    Science.gov (United States)

    Boutros, Youssef Z.; Abd-El-Malek, Mina B.; Badran, Nagwa A.; Hassan, Hossam S.

    2006-12-01

    The unsteady incompressible laminar flow in a semi-infinite porous circular pipe with injection or suction through the pipe wall whose radius varies with time is considered. The present analysis simulates the flow field by the burning of inner surface of cylindrical grain in a solid rocket motor, in which the burning surface regresses with time. We apply Lie-group method for determining symmetry reductions of partial differential equations. Lie-group method starts out with a general infinitesimal group of transformations under which given partial differential equations are invariant, then, the determining equations are derived [Ibragimov, Elementary Lie Group Analysis and Ordinary Differential Equations, Wiley, New York, 1999; Hydon, Symmetry Methods for Differential Equations, Cambridge University Press, Cambridge, 2000; Olver, Applications of Lie Groups to Differential Equations, Springer, New York, 1986; Seshadri, Na, Group invariance in engineering boundary value problems, Springer, New York, 1985; Yi, Fengxiang, Lie symmetries of mechanical systems with unilateral holonomic constraints, Chinese Sci. Bull. 45 (2000) 1354-1358; Moritz, Schwalm, Uherka, Finding Lie groups that reduce the order of discrete dynamical systems, J. Phys. A: Math. 31 (1998) 7379-7402; Nucci, Clarkson, The nonclassical method is more general than the direct method for symmetry reductions. An example of the Fitzhugh-Nagumo equation, Phys. Lett. A 164 (1992) 49-56; Basarab, Lahno, Group classification of nonlinear partial differential equations: a new approach to resolving the problem, Proceedings of Institute of Mathematics of NAS of Ukraine, vol. 43, 2002, pp. 86-92; Burde, Expanded Lie group transformations and similarity reductions of differential equations, Proceedings of Institute of Mathematics of NAS of Ukraine, vol. 43, 2002, pp. 93-101; Gandarias, Bruzon, Classical and nonclassical symmetries of a generalized Boussinesq equation, J. Nonlinear Math. Phys. 5 (1998) 8-12; Hill

  2. Flow

    DEFF Research Database (Denmark)

    2009-01-01

    Flow er en positiv, koncentreret tilstand, hvor al opmærksomhed er samlet om en bestemt aktivitet, som er så krævende og engagerende, at man må anvende mange mentale ressourcer for at klare den. Tidsfornemmelsen forsvinder, og man glemmer sig selv. 'Flow' er den første af en række udsendelser om...

  3. The Geohazards Exploitation Platform

    Science.gov (United States)

    Laur, Henri; Casu, Francesco; Bally, Philippe; Caumont, Hervé; Pinto, Salvatore

    2016-04-01

    The Geohazards Exploitation Platform, or Geohazards TEP (GEP), is an ESA originated R&D activity of the EO ground segment to demonstrate the benefit of new technologies for large scale processing of EO data. This encompasses on-demand processing for specific user needs, systematic processing to address common information needs of the geohazards community, and integration of newly developed processors for scientists and other expert users. The platform supports the geohazards community's objectives as defined in the context of the International Forum on Satellite EO and Geohazards organised by ESA and GEO in Santorini in 2012. The GEP is a follow on to the Supersites Exploitation Platform (SSEP) an ESA initiative to support the Geohazards Supersites & Natural Laboratories initiative (GSNL). Today the GEP allows to exploit 70+ Terabyte of ERS and ENVISAT archive and the Copernicus Sentinel-1 data available on line. The platform has already engaged 22 European early adopters in a validation activity initiated in March 2015. Since September, this validation has reached 29 single user projects. Each project is concerned with either integrating an application, running on demand processing or systematically generating a product collection using an application available in the platform. The users primarily include 15 geoscience centres and universities based in Europe: British Geological Survey (UK), University of Leeds (UK), University College London (UK), ETH University of Zurich (CH), INGV (IT), CNR-IREA and CNR-IRPI (IT), University of L'Aquila (IT), NOA (GR), Univ. Blaise Pascal & CNRS (FR), Ecole Normale Supérieure (FR), ISTERRE / University of Grenoble-Alpes (FR). In addition, there are users from Africa and North America with the University of Rabat (MA) and the University of Miami (US). Furthermore two space agencies and four private companies are involved: the German Space Research Centre DLR (DE), the European Space Agency (ESA), Altamira Information (ES

  4. Exploitative Learning by Exporting

    DEFF Research Database (Denmark)

    Golovko, Elena; Lopes Bento, Cindy; Sofka, Wolfgang

    Decisions on entering foreign markets are among the most challenging but also potentially rewarding strategy choices managers can make. In this study, we examine the effect of export entry on the firm investment decisions in two activities associated with learning about new technologies...... and learning about new markets ? R&D investments and marketing investments, in search of novel insights into the content and process underlying learning by exporting. We draw from organizational learning theory for predicting changes in both R&D and marketing investment patterns that accompany firm entry......, it is predominantly the marketing-related investment decisions associated with starting to export that lead to increases in firm productivity. We conclude that learning-by-exporting might be more properly characterized as ?learning about and exploiting new markets? rather than ?learning about new technologies...

  5. Image exploitation for MISAR

    Science.gov (United States)

    Heinze, N.; Edrich, M.; Saur, G.; Krüger, W.

    2007-04-01

    The miniature SAR-system MiSAR has been developed by EADS Germany for lightweight UAVs like the LUNASystem. MiSAR adds to these tactical UAV-systems the all-weather reconnaissance capability, which is missing until now. Unlike other SAR sensors, that produce large strip maps at update rates of several seconds, MiSAR generates sequences of SAR images with approximately 1 Hz frame rate. photo interpreters (PI) of tactical drones, now mainly experienced with visual interpretation, are not used to SARimages, especially not with SAR-image sequence characteristics. So they should be supported to improve their ability to carry out their task with a new, demanding sensor system. We have therefore analyzed and discussed with military PIs in which task MiSAR can be used and how the PIs can be supported by special algorithms. We developed image processing- and exploitation-algorithms for such SAR-image sequences. A main component is the generation of image sequence mosaics to get more oversight. This mosaicing has the advantage that also non straight /linear flight-paths and varying squint angles can be processed. Another component is a screening-component for manmade objects to mark regions of interest in the image sequences. We use a classification based approach, which can be easily adapted to new sensors and scenes. These algorithms are integrated into an image exploitation system to improve the image interpreters ability to get a better oversight, better orientation and helping them to detect relevant objects, especially considering long endurance reconnaissance missions.

  6. On-line pretreatment and determination of parabens in cosmetic products by combination of flow injection analysis, solid-phase extraction and micellar electrokinetic chromatography.

    Science.gov (United States)

    Han, Fang; He, You-Zhao; Yu, Chang-Zhu

    2008-02-15

    A convenient and automated method for on-line pretreatment and determination of three parabens (i.e. methyl, ethyl and propyl p-hydroxybenzoate) in cosmetic products is proposed by using flow injection analysis (FIA), solid-phase extraction (SPE) and micellar electrokinetic chromatography (MEKC). An improved split-flow interface is used to couple SPE on C(8)-bonded silica with MEKC separation, which can avoid running buffer contamination and reduce buffer consumption, especially, containing expensive reagents. The analytes are loaded onto a C(8) column at 0.6 mL/min for 60s and eluted with a mixed eluent of 40% (v/v) 10 mmol/L sodium tetraborate buffer (pH 9.3) and 60% (v/v) ethanol at 0.75 mL/min. The MEKC separation is accomplished with a running buffer of 20 mmol/L sodium tetraborate (pH 9.3) containing 100 mmol/L sodium dodecyl sulfate (SDS) at 15 kV. For butyl p-hydroxybenzoate did not be detected in the cosmetic products, it was used as an internal standard (IS) added into the real samples. This FIA-SPE-MEKC method using IS allows the sample separation within 12 min and the sample throughput of five samples per hour with the relative standard deviation (R.S.D.) less than 2.3% (n=5). The limits of detection (LOD) are in the range from 0.07 to 0.1 microg/mL (S/N=3 and n=11). The proposed method has been used to determine three parabens in real cosmetic products satisfactorily.

  7. Flow-injection amperometric determination of glucose using a biosensor based on immobilization of glucose oxidase onto Au seeds decorated on core Fe₃O₄ nanoparticles.

    Science.gov (United States)

    Samphao, Anchalee; Butmee, Preeyanut; Jitcharoen, Juthamas; Švorc, Ľubomír; Raber, Georg; Kalcher, Kurt

    2015-09-01

    An amperometric biosensor based on chemisorption of glucose oxidase (GOx) on Au seeds decorated on magnetic core Fe3O4 nanoparticles (Fe3O4@Au) and their immobilization on screen-printed carbon electrode bulk-modified with manganese oxide (SPCE{MnO2}) was designed for the determination of glucose. The Fe3O4@Au/GOx modified SPCE{MnO2} was used in a flow-injection analysis (FIA) arrangement. The experimental conditions were investigated in amperometric mode with the following optimized parameters: flow rate 1.7 mL min(-1), applied potential +0.38 V, phosphate buffer solution (PBS; 0.1 mol L(-1), pH 7.0) as carrier and 3.89 unit mm(-2) enzyme glucose oxidase loading on the active surface of the SPCE. The designed biosensor in FIA arrangement yielded a linear dynamic range for glucose from 0.2 to 9.0 mmol L(-1) with a sensitivity of 2.52 µA mM(-1) cm(-2), a detection limit of 0.1 mmol L(-1) and a quantification limit of 0.3 mmol L(-1). Moreover, a good repeatability of 2.8% (number of measurements n=10) and a sufficient reproducibility of 4.0% (number of sensors n=3) were achieved. It was found that the studied system Fe3O4@Au facilitated not only a simpler enzyme immobilization but also provided wider linear range. The practical application of the proposed biosensor for FIA quantification of glucose was tested in glucose sirup samples, honeys and energy drinks with the results in good accordance with those obtained by an optical glucose meter and with the contents declared by the producers. Copyright © 2015. Published by Elsevier B.V.

  8. Development of an automated in situ analyzer based on ferrozine colorimetry and flow injection analysis to analyze iron in freshwater systems

    Science.gov (United States)

    Cooray, A. T.; Schwingle, R.; Pullin, M. J.

    2011-12-01

    Iron is a common element in the earth crust and also a highly redox active metal in aqueous environments. The chemistry of aqueous iron predominantly involves the common oxidation states of iron, Fe(II) and Fe(III) and their biogeochemical reactions in the oceans, freshwaters, sediments and pore waters. Iron(III) is the thermodynamically stable form of iron in oxic and circumneutral natural waters; however, rapidly hydrolyzes and precipitates and become biologically unavailable. Iron(II) is more soluble and available for many microbial iron uptake strategies but rapidly oxidizes in oxic waters with a half-life in the order of minutes around pH 8. The often rapid interconversion of iron redox states makes in situ analysis preferable. Here we describe the development of an automated in situ iron analyzer based on ferrozine colorimetry and flow injection analysis (FIA) to analyze iron in freshwater systems. Ferrozine selectively reacts with iron(II) in the pH range 4 to 9 to produce a magenta colored 3:1 complex with a maximum absorption at 562 nm. Ferrozine does not react with iron(III) or any of its hydrolytic products. However, total iron determinations can be achieved use reducing agents such as ascorbic acid to reduce iron(III) to iron(II). Ferrozine colorimetry has been used successfully to develop automated iron sensors for marine systems and freshwater systems. Unlike luminol-based chemiluminescence methods, the ferrozine method is not sensitive to the amount of dissolved organic matter present in system or the temperature variations during the analysis. The instrument uses microscale tubing and fittings together with solenoid-based pumps and valves for flow control. Optical detection of the iron(II)-ferrozine complex uses a LED lamp with maximum emission at 560 nm and digital light sensor to avoid the use of complex optics. The instrument analyzes iron(II) and total iron in alternation, with a frequency of 4 minutes.

  9. On-line complexation/cloud point preconcentration for the sensitive determination of dysprosium in urine by flow injection inductively coupled plasma-optical emission spectrometry

    Energy Technology Data Exchange (ETDEWEB)

    Ortega, Claudia; Cerutti, Soledad; Silva, Maria F. [Departamento de Quimica Analitica, Facultad de Quimica, Bioquimica y Farmacia, Universidad Nacional de San Luis, Chacabuco y Pedernera, 5700, San Luis (Argentina); Olsina, Roberto A.; Martinez, Luis D. [Departamento de Quimica Analitica, Facultad de Quimica, Bioquimica y Farmacia, Universidad Nacional de San Luis, Chacabuco y Pedernera, 5700, San Luis (Argentina); Consejo Nacional de Investigaciones Cientificas y Tecnicas (CONICET), Avda. Rivadavia 1917, CP C1033AAJJ, Buenos Aires (Argentina)

    2003-01-01

    An on-line dysprosium preconcentration and determination system based on the hyphenation of cloud point extraction (CPE) to flow injection analysis (FIA) associated with ICP-OES was studied. For the preconcentration of dysprosium, a Dy(III)-2-(5-bromo-2-pyridylazo)-5-diethylaminophenol complex was formed on-line at pH 9.22 in the presence of nonionic micelles of PONPE-7.5. The micellar system containing the complex was thermostated at 30 C in order to promote phase separation, and the surfactant-rich phase was retained in a microcolumn packed with cotton at pH 9.2. The surfactant-rich phase was eluted with 4 mol L{sup -1} nitric acid at a flow rate of 1.5 mL min{sup -1}, directly in the nebulizer of the plasma. An enhancement factor of 50 was obtained for the preconcentration of 50 mL of sample solution. The detection limit value for the preconcentration of 50 mL of aqueous solution of Dy was 0.03 {mu}g L{sup -1}. The precision for 10 replicate determinations at the 2.0 {mu}g L{sup -1}Dy level was 2.2% relative standard deviation (RSD), calculated from the peak heights obtained. The calibration graph using the preconcentration system for dysprosium was linear with a correlation coefficient of 0.9994 at levels near the detection limits up to at least 100 {mu}g L {sup -1}. The method was successfully applied to the determination of dysprosium in urine. (orig.)

  10. Learning Metasploit exploitation and development

    CERN Document Server

    Balapure, Aditya

    2013-01-01

    A practical, hands-on tutorial with step-by-step instructions. The book will follow a smooth and easy-to-follow tutorial approach, covering the essentials and then showing the readers how to write more sophisticated exploits.This book targets exploit developers, vulnerability analysts and researchers, network administrators, and ethical hackers looking to gain advanced knowledge in exploitation development and identifying vulnerabilities. The primary goal is to take readers wishing to get into more advanced exploitation discovery and reaching the next level.Prior experience exploiting basic st

  11. Flare Systems Exploitation and Impact on Permafrost

    Science.gov (United States)

    Filimonov, M. Yu; Vaganova, N. A.

    2017-09-01

    Mathematical models and numerical algorithms of horizontal and vertical flare systems exploitation in northern oil and gas fields located in permafrost zone are developed. Computations of long-term forecasts of permafrost degradation around such constructions have been carried out for various types of operation, including emergency situations, which cause a short-term increase in the heat flow near the ground surface, which leads to an additional soil temperature increasing.

  12. Assessment of trace aluminium content in parenteral solutions by combined cloud point preconcentration-flow injection inductively coupled plasma optical emission spectrometry.

    Science.gov (United States)

    Sombra, Lorena L; Luconi, Marta O; Fernández, Liliana P; Olsina, Roberto A; Silva, María F; Martínez, Luis D

    2003-01-01

    A micelle-mediated phase separation without added chelating agents to preconcentrate trace levels of aluminium in parenteral solutions as a prior step to its determination by flow injection inductively coupled plasma optical emission spectrometry has been developed. The enrichment step is based on the cloud point extraction of aluminium with the non-ionic surfactant polyethyleneglycolmono-p-nonylphenylether (PONPE 7.5). The chemical variables affecting the sensitivity of the extractive-spectrometric procedure were studied in detail. After optimization, a preconcentration factor of 200 and a %E higher than 99.9 were achieved. The detection limit (DL) value of aluminium for the preconcentration of 50 ml of parenteral solution was 0.25 microgl(-1). The calibration graph using the preconcentration system for aluminium was linear with a correlation coefficient of 0.9997 at levels near the DLs up to at least 200 microgl(-1). The developed hyphenated assay, which thoroughly satisfies the typical requirements for pharmaceutical control processes, is appropriate to monitor the aluminium concentration in parenteral nutrition.

  13. Trace mercury determination in drinking and natural water samples by room temperature ionic liquid based-preconcentration and flow injection-cold vapor atomic absorption spectrometry

    Energy Technology Data Exchange (ETDEWEB)

    Martinis, Estefania M.; Berton, Paula [Laboratory of Environmental Research and Services of Mendoza (LISAMEN), (CCT - CONICET - Mendoza), Av. Ruiz Leal S/N Parque General San Martin, CC. 131, M 5502 IRA Mendoza (Argentina); Olsina, Roberto A. [INQUISAL-CONICET, Departamento de Quimica Analitica, Facultad de Quimica, Bioquimica y Farmacia, Universidad Nacional de San Luis, San Luis (Argentina); Altamirano, Jorgelina C. [Laboratory of Environmental Research and Services of Mendoza (LISAMEN), (CCT - CONICET - Mendoza), Av. Ruiz Leal S/N Parque General San Martin, CC. 131, M 5502 IRA Mendoza (Argentina); Instituto de Ciencias Basicas, Universidad Nacional de Cuyo, Mendoza (Argentina); Wuilloud, Rodolfo G., E-mail: rwuilloud@lab.cricyt.edu.ar [Laboratory of Environmental Research and Services of Mendoza (LISAMEN), (CCT - CONICET - Mendoza), Av. Ruiz Leal S/N Parque General San Martin, CC. 131, M 5502 IRA Mendoza (Argentina); Instituto de Ciencias Basicas, Universidad Nacional de Cuyo, Mendoza (Argentina)

    2009-08-15

    A liquid-liquid extraction procedure (L-L) based on room temperature ionic liquid (RTIL) was developed for the preconcentration and determination of mercury in different water samples. The analyte was quantitatively extracted with 1-butyl-3-methylimidazolium hexafluorophosphate ([C{sub 4}mim][PF{sub 6}]) under the form of Hg-2-(5-bromo-2-pyridylazo)-5-diethylaminophenol (Hg-5-Br-PADAP) complex. A volume of 500 {mu}l of 9.0 mol L{sup -1} hydrochloric acid was used to back-extract the analyte from the RTIL phase into an aqueous media prior to its analysis by flow injection-cold vapor atomic absorption spectrometry (FI-CV-AAS). A preconcentration factor of 36 was achieved upon preconcentration of 20 mL of sample. The limit of detection (LOD) obtained under the optimal conditions was 2.3 ng L{sup -1} and the relative standard deviation (RSD) for 10 replicates at 1 {mu}g L{sup -1} Hg{sup 2+} was 2.8%, calculated with peaks height. The method was successfully applied to the determination of mercury in river, sea, mineral and tap water samples and a certified reference material (CRM).

  14. Modeling and Analysis of Magnetic Nanoparticles Injection in Water-Oil Two-Phase Flow in Porous Media under Magnetic Field Effect

    KAUST Repository

    El-Amin, Mohamed

    2017-08-28

    In this paper, the magnetic nanoparticles are injected into a water-oil, two-phase system under the influence of an external permanent magnetic field. We lay down the mathematical model and provide a set of numerical exercises of hypothetical cases to show how an external magnetic field can influence the transport of nanoparticles in the proposed two-phase system in porous media. We treat the water-nanoparticles suspension as a miscible mixture, whereas it is immiscible with the oil phase. The magnetization properties, the density, and the viscosity of the ferrofluids are obtained based on mixture theory relationships. In the mathematical model, the phase pressure contains additional term to account for the extra pressures due to fluid magnetization effect and the magnetostrictive effect. As a proof of concept, the proposed model is applied on a countercurrent imbibition flow system in which both the displacing and the displaced fluids move in opposite directions. Physical variables, including waternanoparticles suspension saturation, nanoparticles concentration, and pore wall/throat concentrations of deposited nanoparticles, are investigated under the influence of the magnetic field. Two different locations of the magnet are studied numerically, and variations in permeability and porosity are considered.

  15. An on-line spectrophotometric determination of trace amounts of thiourea in tap water, orange juice, and orange peel samples using multi-channel flow injection analysis.

    Science.gov (United States)

    Arab Chamjangali, M; Goudarzi, N; Ghochani Moghadam, A; Amin, A H

    2015-01-01

    In this work, a flow injection analysis (FIA) method was introduced for the determination of trace amounts of thiourea in tap water. This method is based upon the inhibition effect of thiourea on the reaction between meta-cresol purple (MCP) and potassium bromate catalyzed by bromide ions in a sulfuric acid medium. In the presence of thiourea, an induction period appears in the reaction system, and as a result, the absorbance of MCP increases at 525 nm in the FIA manifold. The chemical and FIA variables are studied and optimized using the univariate and Simplex optimization methods. Under the optimum conditions, thiourea can be determined in the range of 0.100-13.0 μg mL(-1). The limit of detection (3σ) for thiourea was found to be 0.0310 μg mL(-1). The relative standard deviations (RSDs) for six replicate determinations of 0.500, 5.00, and 12.0 μg mL(-1) of thiourea were 4.0%, 1.8%, and 1.2%, respectively. The proposed method was also applied for the determination of thiourea in orange juice and orange peel samples with recoveries in the range of 98.0-101%. The analytical speed of the method was calculated to be about 120 sample per hour. Copyright © 2015 Elsevier B.V. All rights reserved.

  16. Investigation of iron(III) reduction and trace metal interferences in the determination of dissolved iron in seawater using flow injection with luminol chemiluminescence detection

    Energy Technology Data Exchange (ETDEWEB)

    Ussher, Simon J. [School of Earth, Ocean and Environmental Sciences (SEOES), University of Plymouth, Drake Circus, Plymouth PL4 8AA (United Kingdom); Milne, Angela [School of Earth, Ocean and Environmental Sciences (SEOES), University of Plymouth, Drake Circus, Plymouth PL4 8AA (United Kingdom); Department of Oceanography, Florida State University, Tallahassee, FL 32306-4320 (United States); Landing, William M. [Department of Oceanography, Florida State University, Tallahassee, FL 32306-4320 (United States); Attiq-ur-Rehman, Kakar [Department of Chemistry, University of Balochistan, Quetta (Pakistan); Seguret, Marie J.M.; Holland, Toby [School of Earth, Ocean and Environmental Sciences (SEOES), University of Plymouth, Drake Circus, Plymouth PL4 8AA (United Kingdom); Achterberg, Eric P. [National Oceanography Centre, University of Southampton, European Way, Southampton SO14 3ZH (United Kingdom); Nabi, Abdul [Department of Chemistry, University of Balochistan, Quetta (Pakistan); Worsfold, Paul J., E-mail: pworsfold@plymouth.ac.uk [School of Earth, Ocean and Environmental Sciences (SEOES), University of Plymouth, Drake Circus, Plymouth PL4 8AA (United Kingdom)

    2009-10-12

    A detailed investigation into the performance of two flow injection-chemiluminescence (FI-CL) manifolds (with and without a preconcentration column) for the determination of sub-nanomolar dissolved iron (Fe(II) + Fe(III)), following the reduction of Fe(III) by sulphite, in seawater is described. Kinetic experiments were conducted to examine the efficiency of reduction of inorganic Fe(III) with sulphite under different conditions and a rigorous study of the potential interference caused by other transition metals present in seawater was conducted. Using 100 {mu}M concentrations of sulphite a reduction time of 4 h was sufficient to quantitatively reduce Fe(III) in seawater. Under optimal conditions, cobalt(II) and vanadium(IV)/(III) were the major positive interferences and strategies for their removal are reported. Specifically, cobalt(II) was masked by the addition of dimethylglyoxime to the luminol solution and vanadium(IV) was removed by passing the sample through an 8-hydroxyquinoline column in a low pH carrier stream. Manganese(II) also interfered by suppression of the CL response but this was not significant at typical open ocean concentrations.

  17. A Green Analytical Method Using Ultrasound in Sample Preparation for the Flow Injection Determination of Iron, Manganese, and Zinc in Soluble Solid Samples by Flame Atomic Absorption Spectrometry

    Directory of Open Access Journals (Sweden)

    M. Carmen Yebra

    2012-01-01

    Full Text Available A simple and rapid analytical method was developed for the determination of iron, manganese, and zinc in soluble solid samples. The method is based on continuous ultrasonic water dissolution of the sample (5–30 mg at room temperature followed by flow injection flame atomic absorption spectrometric determination. A good precision of the whole procedure (1.2–4.6% and a sample throughput of ca. 25 samples h–1 were obtained. The proposed green analytical method has been successfully applied for the determination of iron, manganese, and zinc in soluble solid food samples (soluble cocoa and soluble coffee and pharmaceutical preparations (multivitamin tablets. The ranges of concentrations found were 21.4–25.61 μg g-1 for iron, 5.74–18.30 μg g-1 for manganese, and 33.27–57.90 μg g-1 for zinc in soluble solid food samples and 3.75–9.90 μg g-1 for iron, 0.47–5.05 μg g-1 for manganese, and 1.55–15.12 μg g-1 for zinc in multivitamin tablets. The accuracy of the proposed method was established by a comparison with the conventional wet acid digestion method using a paired t-test, indicating the absence of systematic errors.

  18. Masking Agents Evaluation for Lead Determination by Flow Injection-Hydride Generation-Atomic Fluorescence Spectrometry Technique: Effect of KI, L-Cysteine, and 1,10-Phenanthroline

    Directory of Open Access Journals (Sweden)

    Blanca G. Beltrán

    2016-01-01

    Full Text Available Hydride generation (HG of lead technique presents interferences from foreign ions of complex matrix samples. In order to minimize these interferences, the effect of masking agents such as KI, L-cysteine, and 1,10-phenanthroline was studied in the absence and in the presence of selected interfering species (As, Cr, Cu, and Fe. Different modes of addition of masking agents were accomplished, that is, to either sample or KBH4 reducing solution. The lead determinations were performed using a flow injection analysis (FIA system coupled to HG and atomic fluorescence spectrometry (AFS. The linearity of calibration curves (1–10 μg Pb L−1 was not affected by the addition of the masking agents. The use of KI in the reducing solution diminished interferences from concentrations of As and Cu, while 1,10-phenanthroline showed a positive effect on the interference by As. Moreover, Cr and Cu appeared to be the most serious interfering ions for plumbane (PbH4, because they drastically reduced the analytical signal of lead. Fe did not present any interference under the employed experimental conditions, even at high levels. The accuracy was established through the analysis of certified reference material (i.e., BCR-610, groundwater using KI as masking agent. The detection limit reached by FIA-HG-AFS proposed methodology was 0.03 μg Pb L−1.

  19. Highly sensitive determination of diclofenac based on resin beads and a novel polyclonal antibody by using flow injection chemiluminescence competitive immunoassay

    Science.gov (United States)

    Shi, Jing; Xu, Mingxia; Tang, Qinghui; Zhao, Kang; Deng, Anping; Li, Jianguo

    2018-02-01

    A novel flow injection chemiluminescence immunoassay for simple, sensitive and low-cost detection of diclofenac was established based on specific binding of antigen and antibody. Carboxylic resin beads used as solid phase carrier materials provided good biocompatibility and large surface-to-volume ratio for modifying more coating antigen. There was a competitive process between the diclofenac in solution and the immobilized coating antigen to react with the limited binding sites of the polyclonal antibody to form the immunocomplex. The second antibody labelled with horseradish peroxidase was introduced into the immunosensor and trapped by captured polyclonal antibody against diclofenac, which could effectively amplify chemiluminescence signals of luminol-PIP-H2O2. Under optimal conditions, the diclofenac could be detected quantitatively. The chemiluminescence intensity decreased linearly with the logarithm of the diclofenac concentration in the range of 0.1-100 ng mL- 1 with a detection limit of 0.05 ng mL- 1 at a signal-to-noise ratio of 3. The immunosensor exhibited high sensitivity, specificity and acceptable stability. This easy-operated and cost-effective analytical method could be valuable for the diclofenac determination in real water samples.

  20. Determination of protein expression and plasmid copy number from cloned genes in Escherichia coli by flow injection analysis using an enzyme indicator vector.

    Science.gov (United States)

    Schendel, F J; Baude, E J; Flickinger, M C

    1989-10-20

    On-line determination of expression rates from cloned genes in Escherichia coli and of plasmid copy number would be useful for monitoring accumulation of non-secreted proteins. As an initial model for monitoring gene expression in intact cells, a non-gene-fusion enzyme-based indicator plasmid has been constructed containing the phoA gene coding for alkaline phosphatase (AP) in pUCIS and pACYC184. The activity of AP can be rapidly determined in permeabilized cells. A flow injection analysis (FIA) assay has been developed which allows the direct real-time measurement of the AP activity during cell growth. A model target gene coding for E. coli cyanase (cynS) has been inserted in order to determine the ratio between the expression of the target and indicator, AP. A linear relationship has been found between plasmid copy number and AP activity for the high-copy pUC vector. To minimize indicator expression, transcription terminators have been inserted between the cynS and phoA genes, altering the target-to-indicator ratio by 10- to 40-fold. These vectors may be useful for the rapid continuous determination of plasmid copy number and target gene expression for nonsecreted proteins and would overcome the limitations of in situ probe biosensors for real-time determination of the accumulation of proteins from cloned genes in E. coli.

  1. A Green Analytical Method Using Ultrasound in Sample Preparation for the Flow Injection Determination of Iron, Manganese, and Zinc in Soluble Solid Samples by Flame Atomic Absorption Spectrometry

    Science.gov (United States)

    Yebra, M. Carmen

    2012-01-01

    A simple and rapid analytical method was developed for the determination of iron, manganese, and zinc in soluble solid samples. The method is based on continuous ultrasonic water dissolution of the sample (5–30 mg) at room temperature followed by flow injection flame atomic absorption spectrometric determination. A good precision of the whole procedure (1.2–4.6%) and a sample throughput of ca. 25 samples h–1 were obtained. The proposed green analytical method has been successfully applied for the determination of iron, manganese, and zinc in soluble solid food samples (soluble cocoa and soluble coffee) and pharmaceutical preparations (multivitamin tablets). The ranges of concentrations found were 21.4–25.61 μg g−1 for iron, 5.74–18.30 μg g−1 for manganese, and 33.27–57.90 μg g−1 for zinc in soluble solid food samples and 3.75–9.90 μg g−1 for iron, 0.47–5.05 μg g−1 for manganese, and 1.55–15.12 μg g−1 for zinc in multivitamin tablets. The accuracy of the proposed method was established by a comparison with the conventional wet acid digestion method using a paired t-test, indicating the absence of systematic errors. PMID:22567553

  2. Identical flow injection spectrophotometric manifold for determination of protein, phosphorus, calcium, chloride, copper, manganese, iron, and zinc in feeds or premixes.

    Science.gov (United States)

    Liu, J F; Feng, Y D; Jiang, G B

    2001-01-01

    A simple procedure using an identical manifold was developed for determination of nitrogen (protein) phosphorus, calcium, chloride, copper, manganese, iron, and zinc in feeds and feedstuffs. By changing appropriate reagents and detection wavelength, these 8 elements were determined successively with a simple identical double-line flow injection (FI) manifold. Fl spectrophotometric determinations were made by the blue indophenol reaction for ammonium, the molybdenum blue method for phosphate, the cresolphthalein complexone procedure for calcium, and the mercuric thiocyanate procedure for chloride. The chromogenic reagents for copper, iron, manganese, and zinc determination were bis(cyclohexanone)oxalydihydrazone (Cuprizone), 1,10-phenanthroline, formaldoxime, and xylenol orange, respectively. Sample digestion catalyst, Fl manifold, and some chemical parameters were optimized. The proposed procedure had a sampling rate of 90/h for each analyte. The determination ranges (mg/L) were 10-60 for N, 1-15 for P and Ca, 540 for Cl, and 0.5-15 for Cu, Fe, Mn, and Zn, respectively. Results of the analyses of animal feed and feedstuff samples by this procedure did not differ significantly from those obtained by proven manual methods.

  3. Simultaneous determination of nanomole amounts of sulphur dioxide and hydrogen sulphide by flow injection analysis with on-line preconcentration by means of capillary denuder tubes.

    Science.gov (United States)

    Achilli, Marco; Gács, Istvan

    2002-01-01

    A simple and rapid method for trace determination of SO2 and H2S in gaseous samples by using a flow injection system with on line preconcentration on capillary denuder is described. The gaseous samples are led through a 0.4 M sulphamic acid solution, retaining nitrogen dioxide, ammonia and hydrogen chloride. The sulphur dioxide is collected from the carrier gas stream (250 cm3 min-1) as sulphuric acid in a capillary denuder tube coated with a thin layer of 0.01-0.03 M hydrogen peroxide solution of 0.05 mM sulphuric acid; hydrogen sulphide passes into a second tube coated with 0.075 mM sodium sulphide solution of 0.1 M aqueous sodium hydroxide. The films containing the sulphuric acid and the sodium sulphide, respectively, are eluted with the corresponding circulating absorbent streams and pass through the detectors. Sulphuric acid is detected by conductimetry and sulphide is determined spectrophotometrically at 230 nm. If nanoequivalent amounts of H2S are present in the sample containing a large concentration of SO2 (SO2/H2S concentration ratio > 20), the sulphur dioxide is filtered out of the sample gas stream by solid sodium hydrogen carbonate. A limit of detection of 3.5 micrograms m-3 is obtained.

  4. Characterization of the interaction of glycyrrhizin and glycyrrhetinic acid with bovine serum albumin by spectrophotometric-gradient flow injection titration technique and molecular modeling simulations.

    Science.gov (United States)

    Manouchehri, Firouzeh; Izadmanesh, Yahya; Ghasemi, Jahan B

    2017-09-01

    In this research, the interactions of glycyrrhizin (GL) and glycyrrhetinic acid (GA) with bovine serum albumin (BSA) have been investigated by the novel method of spectrophotometric- gradient flow injection titration technique. The hard-modeling multivariate approach to binding was used for calculation of binding constants and estimation of concentration-spectral profiles of equilibrium species. The stoichiometric ratio of binding was estimated using eigenvalue analysis. Results showed that GL and GA bind BSA with overall binding constants of KGL-BSA=3.85 (±0.09)×104Lmol-1, KGA-BSA=3.08 (±0.08)×104Lmol-1. Ligand-BSA complexes were further analyzed by combined docking and molecular dynamics (MD) simulations. Docking simulations were performed to obtain a first guess on the binding structure of the GL/GA-BSA complex, and subsequently analyzed by 20 ns MD simulations in order to evaluate interactions of GL/GA with BSA in detail. Results of MD simulations indicated that GL-BSA complex forms mainly on the basis of hydrogen bonds, while, GA-BSA complex forms on the basis of hydrophobic interactions. Also, water molecules can bridge between the ligand and protein by hydrogen bonds, which are stable during the entire simulation and play an important role in stabilization of the GL/GA-BSA complexes. Copyright © 2017 Elsevier B.V. All rights reserved.

  5. Determination of Noncovalent Binding Using a Continuous Stirred Tank Reactor as a Flow Injection Device Coupled to Electrospray Ionization Mass Spectrometry

    Science.gov (United States)

    Santos, Inês C.; Waybright, Veronica B.; Fan, Hui; Ramirez, Sabra; Mesquita, Raquel B. R.; Rangel, António O. S. S.; Fryčák, Petr; Schug, Kevin A.

    2015-07-01

    Described is a new method based on the concept of controlled band dispersion, achieved by hyphenating flow injection analysis with ESI-MS for noncovalent binding determinations. A continuous stirred tank reactor (CSTR) was used as a FIA device for exponential dilution of an equimolar host-guest solution over time. The data obtained was treated for the noncovalent binding determination using an equimolar binding model. Dissociation constants between vancomycin and Ac-Lys(Ac)-Ala-Ala-OH peptide stereoisomers were determined using both the positive and negative ionization modes. The results obtained for Ac- L-Lys(Ac)- D-Ala- D-Ala (a model for a Gram-positive bacterial cell wall) binding were in reasonable agreement with literature values made by other mass spectrometry binding determination techniques. Also, the developed method allowed the determination of dissociation constants for vancomycin with Ac- L-Lys(Ac)- D-Ala- L-Ala, Ac- L-Lys(Ac)- L-Ala- D-Ala, and Ac- L-Lys(Ac)- L-Ala- L-Ala. Although some differences in measured binding affinities were noted using different ionization modes, the results of each determination were generally consistent. Differences are likely attributable to the influence of a pseudo-physiological ammonium acetate buffer solution on the formation of positively- and negatively-charged ionic complexes.

  6. Determination of As(III) and As(V) in soils using sequential extraction combined with flow injection hydride generation atomic fluorescence detection

    Energy Technology Data Exchange (ETDEWEB)

    Shi Jianbo; Tang Zhiyong; Jin Zexiang; Chi Quan; He Bin; Jiang Guibin

    2003-01-27

    An analytical procedure for determination of As(III) and As(V) in soils using sequential extraction combined with flow injection (FI) hydride generation atomic fluorescence spectrometry (HG-AFS) was presented. The soils were sequentially extracted by water, 0.6 mol l{sup -1} KH{sub 2}PO{sub 4} solution, 1% (v/v) HCl solution and 1% (w/v) NaOH solution. The arsenite (As(III)) in extract was analyzed by HG-AFS in the medium of 0.1 mol l{sup -1} citric acid solution, then the total arsenic in extract was determined by HG-AFS using on-line reduction of arsenate with L-cysteine. The concentration of arsenate (As(V)) was calculated by the difference. The optimum conditions of extraction and determination were studied in detail. The detection limit (3{sigma}) for As(III) and As(V) were 0.11 and 0.07 {mu}g l{sup -1}, respectively. The relative standard deviation (R.S.D.) was 1.43% (n=11) at the 10 {mu}g l{sup -1} As level. The method was applied in the determination of As(III) and As(V) of real soils and the recoveries of As(III) and As(V) were in the range of 89.3-118 and 80.4-111%, respectively.

  7. Ultrasonic extraction followed by sonolysis-ozonolysis as a sample pretreatment method for determination of reactive arsenic toward sodium tetrahydroborate by flow injection-hydride generation AAS.

    Science.gov (United States)

    Capelo, J L; Lavilla, I; Bendicho, C

    2001-08-01

    A new sample pretreatment method based on ultrasonic extraction in HCI medium and subsequent oxidation of the extracts by sonozone (i.e., sonolysis-ozonolysis) has been developed for determination of reactive arsenic toward sodium tetrahydroborate [mainly As(III) + As(V)] by flow injection-hydride generation atomic absorption spectrometry. This method avoids the use of intensive treatments with concentrated and corrosive acids, high pressures, and temperatures that are inherent with traditional wet or dry ashing procedures and entails reduced waste production and reagent consumption. A sonozone process at room temperature was optimized to break the bond of As to proteins and macromolecular constituents which was an essential requirement for effective reduction by L-cysteine prior to arsine generation. Spiking experiments showed that As(III), As(V), MMA, and DMA were fully recovered from several matrixes on applying the above treatment. On the other hand, a nonreducible As species such as arsenobetaine that is predominant in some biological samples remained unchanged. Application of the method to sediment, soil, fly ash, and plant CRMs demonstrated that, in general, a good agreement existed between certified and found As contents, thereby indicating the absence of nonreducible As forms. Low As recoveries were observed for fish CRMs, as a result of the nondegradability of arsenobetaine by sonozone. The detection limit of As in the samples investigated was in the range 0.19-2.8 microg g(-1).

  8. Design and integration of a generic disposable array-compatible sensor housing into an integrated disposable indirect microfluidic flow injection analysis system.

    Science.gov (United States)

    Rapp, Bastian E; Schickling, Benjamin; Prokop, Jürgen; Piotter, Volker; Rapp, Michael; Länge, Kerstin

    2011-10-01

    We describe an integration strategy for arbitrary sensors intended to be used as biosensors in biomedical or bioanalytical applications. For such devices ease of handling (by a potential end user) as well as strict disposable usage are of importance. Firstly we describe a generic array compatible polymer sensor housing with an effective sample volume of 1.55 μl. This housing leaves the sensitive surface of the sensor accessible for the application of biosensing layers even after the embedding. In a second step we show how this sensor housing can be used in combination with a passive disposable microfluidic chip to set up arbitrary 8-fold sensor arrays and how such a system can be complemented with an indirect microfluidic flow injection analysis (FIA) system. This system is designed in a way that it strictly separates between disposable and reusable components- by introducing tetradecane as an intermediate liquid. This results in a sensor system compatible with the demands of most biomedical applications. Comparative measurements between a classical macroscopic FIA system and this integrated indirect microfluidic system are presented. We use a surface acoustic wave (SAW) sensor as an exemplary detector in this work.

  9. Flow injection on-line dilution for multi-element determination in human urine with detection by inductively coupled plasma mass spectrometry

    DEFF Research Database (Denmark)

    Wang, J.H.; Hansen, E.H.; Gammelgaard, Bente

    2001-01-01

    A simple flow injection on-line dilution procedure with detection by inductively coupled plasma mass spectrometry (ICP-MS) was developed for the determination of copper, zinc, arsenic, lead, selenium, nickel and molybdenum in human urine. Matrix effects were minimized by employing a dilution factor...... of 16.5 with on-line standard addition, and Rh-103 was used as internal standard to compensate for signal fluctuation. The procedure was validated by the analysis of two standard reference materials SRM 2670 (NIST) and Seronorm (TM) Trace Elements in Urine. Recovery experiments were pet......-formed by spiking the reference materials as well as artificial urine. The detection limits (mug l(-1)) were 0.12, 0.96, 0.30, 0.09, 0.45, 0.08, 0.09, and the precisions (RSD,%) were 2.6, 2.3, 3.0, 3.7, 3.7, 4.9, 2.8 for Cu, Zn, As, Pb, Se, Ni and Mo, respectively. The procedure was applied to the analysis of 41...

  10. Flow injection on-line dilution for multi-element determination in human urine with detection by inductively coupled plasma mass spectrometry

    DEFF Research Database (Denmark)

    Wang, Jianhua; Hansen, Elo Harald; Gammelgaard, Bente

    2001-01-01

    A simple flow injection on-line dilution procedure with detection by inductively coupled plasma mass spectrometry (ICP-MS) was developed for the determination of copper, zinc, arsenic, lead, selenium, nickel and molybdenum in human urine. Matrix effects were minimized by employing a dilution factor...... of 16.5 with on-line standard addition, and sup/ 103/Rh was used as internal standard to compensate for signal fluctuation. The procedure was validated by the analysis of two standard reference materials SRM 2670 (NIST) and Seronorm(TM) Trace Elements in Urine. Recovery experiments were performed...... by spiking the reference materials as well as artificial urine. The detection limits (mug/l were 0.12, 0.96, 0.30, 0.09, 0.45, 0.08, 0.09, and the precisions (RSD,%) were 2.6, 2.3, 3.0, 3.7, 3.7, 4.9, 2.8 for Cu, Zn, As, Pb, Se, Ni and Mo, respectively. The procedure was applied to the analysis of 41 human...

  11. Modeling and Analysis of Magnetic Nanoparticles Injection in Water-Oil Two-Phase Flow in Porous Media under Magnetic Field Effect

    Directory of Open Access Journals (Sweden)

    Mohamed F. El-Amin

    2017-01-01

    Full Text Available In this paper, the magnetic nanoparticles are injected into a water-oil, two-phase system under the influence of an external permanent magnetic field. We lay down the mathematical model and provide a set of numerical exercises of hypothetical cases to show how an external magnetic field can influence the transport of nanoparticles in the proposed two-phase system in porous media. We treat the water-nanoparticles suspension as a miscible mixture, whereas it is immiscible with the oil phase. The magnetization properties, the density, and the viscosity of the ferrofluids are obtained based on mixture theory relationships. In the mathematical model, the phase pressure contains additional term to account for the extra pressures due to fluid magnetization effect and the magnetostrictive effect. As a proof of concept, the proposed model is applied on a countercurrent imbibition flow system in which both the displacing and the displaced fluids move in opposite directions. Physical variables, including water-nanoparticles suspension saturation, nanoparticles concentration, and pore wall/throat concentrations of deposited nanoparticles, are investigated under the influence of the magnetic field. Two different locations of the magnet are studied numerically, and variations in permeability and porosity are considered.

  12. Iodine speciation in coastal and inland bathing waters and seaweeds extracts using a sequential injection standard addition flow-batch method.

    Science.gov (United States)

    Santos, Inês C; Mesquita, Raquel B R; Bordalo, Adriano A; Rangel, António O S S

    2015-02-01

    The present work describes the development of a sequential injection standard addition method for iodine speciation in bathing waters and seaweeds extracts without prior sample treatment. Iodine speciation was obtained by assessing the iodide and iodate content, the two inorganic forms of iodine in waters. For the determination of iodide, an iodide ion selective electrode (ISE) was used. The indirect determination of iodate was based on the spectrophotometric determination of nitrite (Griess reaction). For the iodate measurement, a mixing chamber was employed (flow batch approach) to explore the inherent efficient mixing, essential for the indirect determination of iodate. The application of the standard addition method enabled detection limits of 0.14 µM for iodide and 0.02 µM for iodate, together with the direct introduction of the target water samples, coastal and inland bathing waters. The results obtained were in agreement with those obtained by ICP-MS and a colorimetric reference procedure. Recovery tests also confirmed the accuracy of the developed method which was effectively applied to bathing waters and seaweed extracts. Copyright © 2014 Elsevier B.V. All rights reserved.

  13. Selective and simultaneous determination of indigo carmine and allura red in candy samples at the nano-concentration range by flow injection analysis with multiple pulse amperometric detection.

    Science.gov (United States)

    Deroco, Patrícia B; Medeiros, Roberta A; Rocha-Filho, Romeu C; Fatibello-Filho, Orlando

    2018-05-01

    A novel, unique electroanalytical method was developed for the simultaneous quantification of the dyes indigo carmine (IC) and allura red (AR) in candies by coupling flow injection analysis and multiple pulse amperometry with a cathodically pretreated boron-doped diamond electrode, using 0.30 mol L-1 H2SO4 as supporting electrolyte. A dual-potential waveform was employed, causing the electrooxidation of either IC solely or IC and AR simultaneously. Thence, subtraction of current signals was used to quantify IC and AR in the concentration ranges of 70.0-1000 nmol L-1 and 40.0-770 nmol L-1, with limits of detection of 40.0 nmol L-1 and 7.0 nmol L-1, respectively. The proposed method, which permits up to 153 determinations per hour with good precision, was successfully applied in the quantification of these dyes in samples of commercial candies; their obtained contents were similar (at a 95% confidence level) to those from a comparative HPLC method. Copyright © 2017 Elsevier Ltd. All rights reserved.

  14. Enhanced chemiluminescence of carminic acid-permanganate by CdS quantum dots and its application for sensitive quenchometric flow injection assays of cloxacillin.

    Science.gov (United States)

    Khataee, Alireza; Hasanzadeh, Aliyeh; Lotfi, Roya; Joo, Sang Woo

    2016-05-15

    A novel chemiluminescence (CL) system is introduced based on the oxidation of carminic acid by KMnO4 in acidic conditions. CdS quantum dots (QDs) were synthesized using a facile hydrothermal method which efficiently enhanced the intensity of the CL system. A possible mechanism for the proposed system is presented using the kinetic curves, CL spectra, photoluminescence (PL), and ultraviolet-visible (UV-Vis) analysis. The emission intensity of the KMnO4-carminic acid-CdS QDs system was quenched in the presence of a trace level of cloxacillin. Based on this quenching effect, a novel and sensitive flow injection CL method was developed for determining cloxacillin concentrations. At optimal experimental conditions, the decreased CL intensity had a good linear relation with the cloxacillin concentration in the range of 0.008 to 22.0 mg L(-1). The detection limit (3σ) was 5.8 µg L(-1). The precision of the method was calculated by analyzing samples containing 4.0 mg L(-1) of cloxacillin (n=11), and the relative standard deviations (RSD%) were 2.08%. The feasibility of the method is also demonstrated for determining cloxacillin concentrations in environmental water samples and a pharmaceutical formulation. Copyright © 2016 Elsevier B.V. All rights reserved.

  15. A gas-diffusion flow injection method coupled with online solid-liquid extraction for the determination of ammonium in solid samples.

    Science.gov (United States)

    Timofeeva, Irina I; Bulatov, Andrey V; Moskvin, Aleksey L; Kolev, Spas D

    2015-09-01

    A simple, rapid and reliable gas-diffusion flow injection (GD-FI) method for ammonium determination in building materials has been developed. It is based on leaching ammonium from a ground solid sample into an alkaline solution with subsequent ammonia gas generation. Ammonia is then transported in a nitrogen stream to the GD cell of the FI system where it is absorbed into its acceptor solution containing a mixture of the acid-base indicators cresol red and thymol blue. The maximum increase in the absorbance of the acceptor solution at 580 nm is related to the ammonium concentration in the solid sample. The proposed method is characterized by a linear concentration range of 0.1-5.0 mg NH4(+) kg(-1), a limit of detection of 8 μg NH4(+) kg(-1) and a sample throughput of 10h(-1). A successful application of this method for the determination of ammonium in building materials such as concrete, cement and sand is reported. Copyright © 2015 Elsevier B.V. All rights reserved.

  16. A novel solidified floating organic drop microextraction method for preconcentration and determination of copper ions by flow injection flame atomic absorption spectrometry in water samples

    Directory of Open Access Journals (Sweden)

    Arpa Şahin Ç.

    2013-04-01

    Full Text Available A simple, rapid and inexpensive solidified floating organic drop microextraction (SFODME and flow injection flame atomic absorption spectrometric determination (FI-FAAS method for copper was developed. 3-amino-7-dimethylamino-2-methylphenazine (Neutral red, NR was used as the complexing agent. Several factors affecting the microextraction efficiency, such as, pH, NR and sodium dodecylbenzenesulfonate (SDBS concentration, extraction time, stirring rate, and temperature were investigated and optimized. Under optimized experimental conditions an enrichment factor of 541 was obtained for 100 mL of sample solution. The calibration graph was linear in the range of 0.5 – 20.0 ng mL–1 and the limit of detection (3s was 0.18 ng mL–1, the limit of quantification (10s was 0.58 ng mL–1. The relative standard deviation (RSD for 10 replicate measurements of 10 ng mL–1 copper was 2.7%. The developed method was successfully applied to the extraction and determination of copper in different certified reference materials (Estuarine water, Slew 3 and fortified water, TM 23.2 and real water samples and satisfactory results were obtained.

  17. Determination of chemical oxygen demand by a flow injection method based on microwave digestion and chromium speciation coupled to inductively coupled plasma optical emission spectrometry.

    Science.gov (United States)

    Almeida, César A; González, Patricia; Mallea, Miguel; Martinez, Luis D; Gil, Raúl A

    2012-08-15

    The present paper evaluates the applicability of a new FIA system for COD determination. The new system, flow injection microwave solid phase extraction by means of activated carbon (FI-MW-SPE), consists of a digestion circuit, placed in a home MW oven, coupled to an ICP-OES spectrophotometer. Doehlert experimental design was used to speed up the optimization of different experimental variables studied for assisted digestion methods. The method provided a high throughput of about 18 samples h(-1). To assess the accuracy of analytical methods linear regression, elliptic joint confidence region (EJCR) was used. A large linear range of 2.78-850 mg O(2) L(-1) with an excellent detection limit of 0.94 mg O(2) L(-1) was obtained. The interference by high chloride concentration was studied, and values below 3000 mg Cl(-) ions L(-1), allowed the estimation of COD load without any masking agents. COD values for various types of wastewater samples were correlated with those obtained by standard manual methods. Moreover, interferences due to matrix nature are absent; since matrix is washed out of the column before Cr (III) is eluted. This method reduces the time, reagent volume, hazardous emission, external contamination, with a good reproducibility and accuracy. Copyright © 2012. Published by Elsevier B.V.

  18. In-line electrochemical reagent generation coupled to a flow injection biamperometric system for the determination of sulfite in beverage samples.

    Science.gov (United States)

    de Paula, Nattany T G; Barbosa, Elaine M O; da Silva, Paulo A B; de Souza, Gustavo C S; Nascimento, Valberes B; Lavorante, André F

    2016-07-15

    This work reports an in-line electrochemical reagent generation coupled to a flow injection biamperometric procedure for the determination of SO3(2-). The method was based on a redox reaction between the I3(-) and SO3(2-) ions, after the diffusion of SO2 through a gas diffusion chamber. Under optimum experimental conditions, a linear response ranging from 1.0 to 12.0 mg L(-1) (R=0.9999 and n=7), a detection and quantification limit estimated at 0.26 and 0.86 mg L(-1), respectively, a standard deviation relative of 0.4% (n=10) for a reference solution of 4.0 mg L(-1) SO3(2-) and sampling throughput for 40 determinations per hour were achieved. Addition and recovery tests with juice and wine samples were performed resulting in a range between 92% and 110%. There were no significant differences at a 95% confidence level in the analysis of eight samples when comparing the new method with a reference procedure. Copyright © 2016 Elsevier Ltd. All rights reserved.

  19. Tacrolimus Injection

    Science.gov (United States)

    Tacrolimus injection is used along with other medications to prevent rejection (attack of the transplanted organ by ... who have received kidney, liver, or heart transplants. Tacrolimus injection should only be used by people who ...

  20. Naltrexone Injection

    Science.gov (United States)

    Vivitrol® ... Naltrexone injection is used along with counseling and social support to help people who have stopped drinking large amounts of alcohol to avoid drinking again. Naltrexone injection is also used along with counseling and social ...

  1. Cefazolin Injection

    Science.gov (United States)

    Cefazolin injection is used to treat certain infections caused by bacteria including skin, bone, joint, genital, blood, heart valve, ... pneumonia), biliary tract, and urinary tract infections. Cefazolin injection also may be used before, during, and sometimes ...

  2. Mipomersen Injection

    Science.gov (United States)

    Mipomersen injection is used to decrease levels of cholesterol and other fatty substances in the blood in people who ... that removes LDL from the blood), but mipomersen injection should not be used along with this treatment. ...

  3. Denosumab Injection

    Science.gov (United States)

    Denosumab injection (Prolia) is used to treat osteoporosis (a condition in which the bones become thin and weak and ... not respond to other medications for osteoporosis. Denosumab injection (Prolia) is also used to treat bone loss ...

  4. Ampicillin Injection

    Science.gov (United States)

    Ampicillin injection is used to treat certain infections that are caused by bacteria such as meningitis (infection of the ... heart, urinary tract, and gastrointestinal tract infections. Ampicillin injection is in a class of medications called penicillins. ...

  5. Cefotetan Injection

    Science.gov (United States)

    Cefotetan injection is used to treat infections of the lungs, skin, bones, joints, stomach area, blood, female reproductive organs, and urinary tract. Cefotetan injection is also used before surgery to prevent infections. ...

  6. Eculizumab Injection

    Science.gov (United States)

    Eculizumab injection is used to treat paroxysmal nocturnal hemoglobinuria (PNH: a type of anemia in which too many red ... oxygen to all parts of the body). Eculizumab injection is also used to treat atypical hemolytic uremic ...

  7. Tigecycline Injection

    Science.gov (United States)

    Tigecycline injection used to treat certain serious infections including community acquired pneumonia (a lung infection that developed in a ... area between the chest and the waist). Tigecycline injection should not be used to treat pneumonia that ...

  8. Estrogen Injection

    Science.gov (United States)

    ... estradiol cypionate and estradiol valerate forms of estrogen injection are used to treat hot flushes (hot flashes; ... consider a different treatment. These forms of estrogen injection are also sometimes used to treat the symptoms ...

  9. Ceftazidime Injection

    Science.gov (United States)

    Ceftazidime injection is used to treat certain infections caused by bacteria including pneumonia and other lower respiratory tract (lung) ... female genital tract, and urinary tract infections. Ceftazidime injection is in a class of medications called cephalosporin ...

  10. Tobramycin Injection

    Science.gov (United States)

    Tobramycin injection is used to treat certain serious infections that are caused by bacteria such as meningitis (infection of ... lungs, skin, bones, joints, and urinary tract. Tobramycin injection is in a class of medications called aminoglycoside ...

  11. Cefoxitin Injection

    Science.gov (United States)

    Cefoxitin injection is used to treat infections caused by bacteria including pneumonia and other lower respiratory tract (lung) infections; ... organs, blood, bone, joint, and skin infections. Cefoxitin injection may also be used before and during surgery, ...

  12. Naloxone Injection

    Science.gov (United States)

    Naloxone injection and naloxone prefilled auto-injection device (Evzio) are used along with emergency medical treatment to reverse the life-threatening effects of a known or suspected opiate (narcotic) ...

  13. Cyanocobalamin Injection

    Science.gov (United States)

    Cyanocobalamin injection is used to treat and prevent a lack of vitamin B12 that may be caused by any ... organs) and permanent damage to the nerves. Cyanocobalamin injection also may be given as a test to ...

  14. Dulaglutide Injection

    Science.gov (United States)

    Dulaglutide injection is used with a diet and exercise program to control blood sugar levels in adults with type ... medications did not control levels well enough. Dulaglutide injection is not used to treat type 1 diabetes ( ...

  15. Mitoxantrone Injection

    Science.gov (United States)

    Mitoxantrone injection is used to decrease the number of symptom episodes and slow the development of disability in patients with certain forms of multiple sclerosis (MS). Mitoxantrone injection is also used together with steroid medications to ...

  16. Testosterone Injection

    Science.gov (United States)

    ... and testosterone pellet (Testopel) are forms of testosterone injection used to treat symptoms of low testosterone in ... are low before you begin to use testosterone injection. Testosterone enanthate (Delatestryl) and testosterone pellet (Testopel) are ...

  17. Cefepime Injection

    Science.gov (United States)

    Cefepime injection is used to treat certain infections caused by bacteria including pneumonia, and skin, urinary tract, and kidney infections. Cefepime injection is used in combination with metronidazole (Flagyl) to ...

  18. Ranitidine Injection

    Science.gov (United States)

    Ranitidine injection is used in people who are hospitalized to treat certain conditions in which the stomach produces too ... were not successfully treated with other medications. Ranitidine injection is also used on a short-term basis ...

  19. Gentamicin Injection

    Science.gov (United States)

    Gentamicin injection is used to treat certain serious infections that are caused by bacteria such as meningitis (infection of ... lungs, skin, bones, joints, and urinary tract. Gentamicin injection is in a class of medications called aminoglycoside ...

  20. Meropenem Injection

    Science.gov (United States)

    Meropenem injection is used to treat skin and abdominal (stomach area) infections caused by bacteria and meningitis (infection of ... children 3 months of age and older. Meropenem injection is in a class of medications called antibiotics. ...