Design and Experimental Study on Spinning Solid Rocket Motor

Science.gov (United States)

Xue, Heng; Jiang, Chunlan; Wang, Zaicheng

The study on spinning solid rocket motor (SRM) which used as power plant of twice throwing structure of aerial submunition was introduced. This kind of SRM which with the structure of tangential multi-nozzle consists of a combustion chamber, propellant charge, 4 tangential nozzles, ignition device, etc. Grain design, structure design and prediction of interior ballistic performance were described, and problem which need mainly considered in design were analyzed comprehensively. Finally, in order to research working performance of the SRM, measure pressure-time curve and its speed, static test and dynamic test were conducted respectively. And then calculated values and experimental data were compared and analyzed. The results indicate that the designed motor operates normally, and the stable performance of interior ballistic meet demands. And experimental results have the guidance meaning for the pre-research design of SRM.

The role of experimental typography in designing logotypes

OpenAIRE

Pogačnik, Tadeja

2014-01-01

Designing logotypes is an important part of graphic design. Great logotypes are designed using custom made typefaces. Therefore, it is very important, especially for the typographic designer, to have practical experience and be up to date with all trends in the field of experimental typefaces design, also called experimental typography. In my thesis statement, I carefully examined the problems of experimental typography - which allows more creative and free typography designing for different ...

Experimental design in chemistry: A tutorial.

Science.gov (United States)

Leardi, Riccardo

2009-10-12

In this tutorial the main concepts and applications of experimental design in chemistry will be explained. Unfortunately, nowadays experimental design is not as known and applied as it should be, and many papers can be found in which the "optimization" of a procedure is performed one variable at a time. Goal of this paper is to show the real advantages in terms of reduced experimental effort and of increased quality of information that can be obtained if this approach is followed. To do that, three real examples will be shown. Rather than on the mathematical aspects, this paper will focus on the mental attitude required by experimental design. The readers being interested to deepen their knowledge of the mathematical and algorithmical part can find very good books and tutorials in the references [G.E.P. Box, W.G. Hunter, J.S. Hunter, Statistics for Experimenters: An Introduction to Design, Data Analysis, and Model Building, John Wiley & Sons, New York, 1978; R. Brereton, Chemometrics: Data Analysis for the Laboratory and Chemical Plant, John Wiley & Sons, New York, 1978; R. Carlson, J.E. Carlson, Design and Optimization in Organic Synthesis: Second Revised and Enlarged Edition, in: Data Handling in Science and Technology, vol. 24, Elsevier, Amsterdam, 2005; J.A. Cornell, Experiments with Mixtures: Designs, Models and the Analysis of Mixture Data, in: Series in Probability and Statistics, John Wiley & Sons, New York, 1991; R.E. Bruns, I.S. Scarminio, B. de Barros Neto, Statistical Design-Chemometrics, in: Data Handling in Science and Technology, vol. 25, Elsevier, Amsterdam, 2006; D.C. Montgomery, Design and Analysis of Experiments, 7th edition, John Wiley & Sons, Inc., 2009; T. Lundstedt, E. Seifert, L. Abramo, B. Thelin, A. Nyström, J. Pettersen, R. Bergman, Chemolab 42 (1998) 3; Y. Vander Heyden, LC-GC Europe 19 (9) (2006) 469].

Experimental design of a waste glass study

International Nuclear Information System (INIS)

Piepel, G.F.; Redgate, P.E.; Hrma, P.

1995-04-01

A Composition Variation Study (CVS) is being performed to support a future high-level waste glass plant at Hanford. A total of 147 glasses, covering a broad region of compositions melting at approximately 1150 degrees C, were tested in five statistically designed experimental phases. This paper focuses on the goals, strategies, and techniques used in designing the five phases. The overall strategy was to investigate glass compositions on the boundary and interior of an experimental region defined by single- component, multiple-component, and property constraints. Statistical optimal experimental design techniques were used to cover various subregions of the experimental region in each phase. Empirical mixture models for glass properties (as functions of glass composition) from previous phases wee used in designing subsequent CVS phases

Robust Bayesian Experimental Design for Conceptual Model Discrimination

Science.gov (United States)

Pham, H. V.; Tsai, F. T. C.

2015-12-01

A robust Bayesian optimal experimental design under uncertainty is presented to provide firm information for model discrimination, given the least number of pumping wells and observation wells. Firm information is the maximum information of a system can be guaranteed from an experimental design. The design is based on the Box-Hill expected entropy decrease (EED) before and after the experiment design and the Bayesian model averaging (BMA) framework. A max-min programming is introduced to choose the robust design that maximizes the minimal Box-Hill EED subject to that the highest expected posterior model probability satisfies a desired probability threshold. The EED is calculated by the Gauss-Hermite quadrature. The BMA method is used to predict future observations and to quantify future observation uncertainty arising from conceptual and parametric uncertainties in calculating EED. Monte Carlo approach is adopted to quantify the uncertainty in the posterior model probabilities. The optimal experimental design is tested by a synthetic 5-layer anisotropic confined aquifer. Nine conceptual groundwater models are constructed due to uncertain geological architecture and boundary condition. High-performance computing is used to enumerate all possible design solutions in order to identify the most plausible groundwater model. Results highlight the impacts of scedasticity in future observation data as well as uncertainty sources on potential pumping and observation locations.

Chemicals-Based Formulation Design: Virtual Experimentations

DEFF Research Database (Denmark)

Conte, Elisa; Gani, Rafiqul

2011-01-01

This paper presents a systematic procedure for virtual experimentations related to the design of liquid formulated products. All the experiments that need to be performed when designing a liquid formulated product (lotion), such as ingredients selection and testing, solubility tests, property mea...... on the design of an insect repellent lotion will show that the software is an essential instrument in decision making, and that it reduces time and resources since experimental efforts can be focused on one or few product alternatives....

Considering RNAi experimental design in parasitic helminths.

Science.gov (United States)

Dalzell, Johnathan J; Warnock, Neil D; McVeigh, Paul; Marks, Nikki J; Mousley, Angela; Atkinson, Louise; Maule, Aaron G

2012-04-01

Almost a decade has passed since the first report of RNA interference (RNAi) in a parasitic helminth. Whilst much progress has been made with RNAi informing gene function studies in disparate nematode and flatworm parasites, substantial and seemingly prohibitive difficulties have been encountered in some species, hindering progress. An appraisal of current practices, trends and ideals of RNAi experimental design in parasitic helminths is both timely and necessary for a number of reasons: firstly, the increasing availability of parasitic helminth genome/transcriptome resources means there is a growing need for gene function tools such as RNAi; secondly, fundamental differences and unique challenges exist for parasite species which do not apply to model organisms; thirdly, the inherent variation in experimental design, and reported difficulties with reproducibility undermine confidence. Ideally, RNAi studies of gene function should adopt standardised experimental design to aid reproducibility, interpretation and comparative analyses. Although the huge variations in parasite biology and experimental endpoints make RNAi experimental design standardization difficult or impractical, we must strive to validate RNAi experimentation in helminth parasites. To aid this process we identify multiple approaches to RNAi experimental validation and highlight those which we deem to be critical for gene function studies in helminth parasites.

Design and experimentation of BSFQ logic devices

International Nuclear Information System (INIS)

Hosoki, T.; Kodaka, H.; Kitagawa, M.; Okabe, Y.

1999-01-01

Rapid single flux quantum (RSFQ) logic needs synchronous pulses for each gate, so the clock-wiring problem is more serious when designing larger scale circuits with this logic. So we have proposed a new SFQ logic which follows Boolean algebra perfectly by using set and reset pulses. With this logic, the level information of current input is transmitted with these pulses generated by level-to-pulse converters, and each gate calculates logic using its phase level made by these pulses. Therefore, our logic needs no clock in each gate. We called this logic 'Boolean SFQ (BSFQ) logic'. In this paper, we report design and experimentation for an AND gate with inverting input based on BSFQ logic. The experimental results for OR and XOR gates are also reported. (author)

Experimental Design: Review and Comment.

Science.gov (United States)

1984-02-01

creativity. Innovative modifications and extensions of classical experimental designs were developed and many useful articles were published in a short...Pjrazolone Industrielle ," Bulletin de la Soci~t6 Chimique de France, 11-12, 1171-1174. LI, K. C. (1983), "Minimaxity for Randomized Designs: Some

Conceptual design of fusion experimental reactor (FER)

International Nuclear Information System (INIS)

1985-01-01

The Fusion Experimental Reactor (FER) being developed at JAERI as a next generation tokamak to JT-60 has a major mission of realizing a self-ignited long-burning DT plasma and demonstrating engineering feasibility. During FY82 and FY83 a comprehensive and intensive conceptual design study has been conducted for a pulsed operation FER as a reference option which employs a conventional inductive current drive and a double-null divertor. In parallel with the reference design, studies have been carried out to evaluate advanced reactor concepts such as quasi-steady state operation and steady state operation based on RF current drive and pumped limiter, and comparative studies for single-null divertor/pumped limiter. This report presents major results obtained primarily from FY83 design studies, while the results of FY82 design studies are described in previous references (JAERI-M 83-213--216). (author)

Experimental Design: Utilizing Microsoft Mathematics in Teaching and Learning Calculus

Science.gov (United States)

Oktaviyanthi, Rina; Supriani, Yani

2015-01-01

The experimental design was conducted to investigate the use of Microsoft Mathematics, free software made by Microsoft Corporation, in teaching and learning Calculus. This paper reports results from experimental study details on implementation of Microsoft Mathematics in Calculus, students' achievement and the effects of the use of Microsoft…

Sequential experimental design based generalised ANOVA

Energy Technology Data Exchange (ETDEWEB)

Chakraborty, Souvik, E-mail: csouvik41@gmail.com; Chowdhury, Rajib, E-mail: rajibfce@iitr.ac.in

2016-07-15

Over the last decade, surrogate modelling technique has gained wide popularity in the field of uncertainty quantification, optimization, model exploration and sensitivity analysis. This approach relies on experimental design to generate training points and regression/interpolation for generating the surrogate. In this work, it is argued that conventional experimental design may render a surrogate model inefficient. In order to address this issue, this paper presents a novel distribution adaptive sequential experimental design (DA-SED). The proposed DA-SED has been coupled with a variant of generalised analysis of variance (G-ANOVA), developed by representing the component function using the generalised polynomial chaos expansion. Moreover, generalised analytical expressions for calculating the first two statistical moments of the response, which are utilized in predicting the probability of failure, have also been developed. The proposed approach has been utilized in predicting probability of failure of three structural mechanics problems. It is observed that the proposed approach yields accurate and computationally efficient estimate of the failure probability.

HYDROïD humanoid robot head with perception and emotion capabilities :Modeling, Design and Experimental Results

Directory of Open Access Journals (Sweden)

Samer eAlfayad

2016-04-01

Full Text Available In the framework of the HYDROïD humanoid robot project, this paper describes the modeling and design of an electrically actuated head mechanism. Perception and emotion capabilities are considered in the design process. Since HYDROïD humanoid robot is hydraulically actuated, the choice of electrical actuation for the head mechanism addressed in this paper is justified. Considering perception and emotion capabilities leads to a total number of 15 degrees of freedom for the head mechanism which are split on four main sub-mechanisms: the neck, the mouth, the eyes and the eyebrows. Biological data and kinematics performances of human head are taken as inputs of the design process. A new solution of uncoupled eyes is developed to possibly address the master-slave process that links the human eyes as well as vergence capabilities. Modeling each sub-system is carried out in order to get equations of motion, their frequency responses and their transfer functions. The neck pitch rotation is given as a study example. Then, the head mechanism performances are presented through a comparison between model and experimental results validating the hardware capabilities. Finally, the head mechanism is integrated on the HYDROïD upper-body. An object tracking experiment coupled with emotional expressions is carried out to validate the synchronization of the eye rotations with the body motions.

An Empirical Study of Parameter Estimation for Stated Preference Experimental Design

Directory of Open Access Journals (Sweden)

Fei Yang

2014-01-01

Full Text Available The stated preference experimental design can affect the reliability of the parameters estimation in discrete choice model. Some scholars have proposed some new experimental designs, such as D-efficient, Bayesian D-efficient. But insufficient empirical research has been conducted on the effectiveness of these new designs and there has been little comparative analysis of the new designs against the traditional designs. In this paper, a new metro connecting Chengdu and its satellite cities is taken as the research subject to demonstrate the validity of the D-efficient and Bayesian D-efficient design. Comparisons between these new designs and orthogonal design were made by the fit of model and standard deviation of parameters estimation; then the best model result is obtained to analyze the travel choice behavior. The results indicate that Bayesian D-efficient design works better than D-efficient design. Some of the variables can affect significantly the choice behavior of people, including the waiting time and arrival time. The D-efficient and Bayesian D-efficient design for MNL can acquire reliability result in ML model, but the ML model cannot develop the theory advantages of these two designs. Finally, the metro can handle over 40% passengers flow if the metro will be operated in the future.

Experimental design and quantitative analysis of microbial community multiomics.

Science.gov (United States)

Mallick, Himel; Ma, Siyuan; Franzosa, Eric A; Vatanen, Tommi; Morgan, Xochitl C; Huttenhower, Curtis

2017-11-30

Studies of the microbiome have become increasingly sophisticated, and multiple sequence-based, molecular methods as well as culture-based methods exist for population-scale microbiome profiles. To link the resulting host and microbial data types to human health, several experimental design considerations, data analysis challenges, and statistical epidemiological approaches must be addressed. Here, we survey current best practices for experimental design in microbiome molecular epidemiology, including technologies for generating, analyzing, and integrating microbiome multiomics data. We highlight studies that have identified molecular bioactives that influence human health, and we suggest steps for scaling translational microbiome research to high-throughput target discovery across large populations.

Fundamentals of statistical experimental design and analysis

CERN Document Server

Easterling, Robert G

2015-01-01

Professionals in all areas - business; government; the physical, life, and social sciences; engineering; medicine, etc. - benefit from using statistical experimental design to better understand their worlds and then use that understanding to improve the products, processes, and programs they are responsible for. This book aims to provide the practitioners of tomorrow with a memorable, easy to read, engaging guide to statistics and experimental design. This book uses examples, drawn from a variety of established texts, and embeds them in a business or scientific context, seasoned with a dash of humor, to emphasize the issues and ideas that led to the experiment and the what-do-we-do-next? steps after the experiment. Graphical data displays are emphasized as means of discovery and communication and formulas are minimized, with a focus on interpreting the results that software produce. The role of subject-matter knowledge, and passion, is also illustrated. The examples do not require specialized knowledge, and t...

Bioinspiration: applying mechanical design to experimental biology.

Science.gov (United States)

Flammang, Brooke E; Porter, Marianne E

2011-07-01

The production of bioinspired and biomimetic constructs has fostered much collaboration between biologists and engineers, although the extent of biological accuracy employed in the designs produced has not always been a priority. Even the exact definitions of "bioinspired" and "biomimetic" differ among biologists, engineers, and industrial designers, leading to confusion regarding the level of integration and replication of biological principles and physiology. By any name, biologically-inspired mechanical constructs have become an increasingly important research tool in experimental biology, offering the opportunity to focus research by creating model organisms that can be easily manipulated to fill a desired parameter space of structural and functional repertoires. Innovative researchers with both biological and engineering backgrounds have found ways to use bioinspired models to explore the biomechanics of organisms from all kingdoms to answer a variety of different questions. Bringing together these biologists and engineers will hopefully result in an open discourse of techniques and fruitful collaborations for experimental and industrial endeavors.

Design and experimental characterization of an EM pump

International Nuclear Information System (INIS)

Kim, Hee Reyoung; Hong, Sang Hee

1999-01-01

Generally, an EM (electromagnetic) pump is been employed to circulate electrically conducting liquids by using the Lorentz force. Especially, at the liquid metal reactor (LMR), which uses liquid sodium with high electrical conductivity as a coolant, an EM pump is needed due to its advantages over a mechanical pump, such as no rotating parts, no noise, and simplicity. In this research, an EM pump of a pilot annular linear induction type with a flow rate of 200 l/min was designed by using the electrical equivalent-circuit method. The pump was designed and manufactured by considering material and environmental (high temperature and liquid sodium) requirements. The pump performance was experimentally characterized based on input currents, voltage, power, and frequency. Also, the theoretical prediction was compared with the experimental result

Results of an Advanced Fan Stage Operating Over a Wide Range of Speed and Bypass Ratio. Part 1; Fan Stage Design and Experimental Results

Science.gov (United States)

Suder, Kenneth L.; Prahst, Patricia S.; Thorp, Scott A.

2011-01-01

NASA s Fundamental Aeronautics Program is investigating turbine-based combined cycle (TBCC) propulsion systems for access to space because it provides the potential for aircraft-like, space-launch operations that may significantly reduce launch costs and improve safety. To this end, National Aeronautics and Space Administration (NASA) and General Electric (GE) teamed to design a Mach 4 variable cycle turbofan/ramjet engine for access to space. To enable the wide operating range of a Mach 4+ variable cycle turbofan ramjet required the development of a unique fan stage design capable of multi-point operation to accommodate variations in bypass ratio (10 ), fan speed (7 ), inlet mass flow (3.5 ), inlet pressure (8 ), and inlet temperature (3 ). In this paper, NASA has set out to characterize a TBCC engine fan stage aerodynamic performance and stability limits over a wide operating range including power-on and hypersonic-unique "windmill" operation. Herein, we will present the fan stage design, and the experimental test results of the fan stage operating from 15 to 100 percent corrected design speed. Whereas, in the companion paper, we will provide an assessment of NASA s APNASA code s ability to predict the fan stage performance and operability over a wide range of speed and bypass ratio.

Constructing experimental designs for discrete-choice experiments: report of the ISPOR Conjoint Analysis Experimental Design Good Research Practices Task Force.

Science.gov (United States)

Reed Johnson, F; Lancsar, Emily; Marshall, Deborah; Kilambi, Vikram; Mühlbacher, Axel; Regier, Dean A; Bresnahan, Brian W; Kanninen, Barbara; Bridges, John F P

2013-01-01

Stated-preference methods are a class of evaluation techniques for studying the preferences of patients and other stakeholders. While these methods span a variety of techniques, conjoint-analysis methods-and particularly discrete-choice experiments (DCEs)-have become the most frequently applied approach in health care in recent years. Experimental design is an important stage in the development of such methods, but establishing a consensus on standards is hampered by lack of understanding of available techniques and software. This report builds on the previous ISPOR Conjoint Analysis Task Force Report: Conjoint Analysis Applications in Health-A Checklist: A Report of the ISPOR Good Research Practices for Conjoint Analysis Task Force. This report aims to assist researchers specifically in evaluating alternative approaches to experimental design, a difficult and important element of successful DCEs. While this report does not endorse any specific approach, it does provide a guide for choosing an approach that is appropriate for a particular study. In particular, it provides an overview of the role of experimental designs for the successful implementation of the DCE approach in health care studies, and it provides researchers with an introduction to constructing experimental designs on the basis of study objectives and the statistical model researchers have selected for the study. The report outlines the theoretical requirements for designs that identify choice-model preference parameters and summarizes and compares a number of available approaches for constructing experimental designs. The task-force leadership group met via bimonthly teleconferences and in person at ISPOR meetings in the United States and Europe. An international group of experimental-design experts was consulted during this process to discuss existing approaches for experimental design and to review the task force's draft reports. In addition, ISPOR members contributed to developing a consensus

Experimental design research approaches, perspectives, applications

CERN Document Server

Stanković, Tino; Štorga, Mario

2016-01-01

This book presents a new, multidisciplinary perspective on and paradigm for integrative experimental design research. It addresses various perspectives on methods, analysis and overall research approach, and how they can be synthesized to advance understanding of design. It explores the foundations of experimental approaches and their utility in this domain, and brings together analytical approaches to promote an integrated understanding. The book also investigates where these approaches lead to and how they link design research more fully with other disciplines (e.g. psychology, cognition, sociology, computer science, management). Above all, the book emphasizes the integrative nature of design research in terms of the methods, theories, and units of study—from the individual to the organizational level. Although this approach offers many advantages, it has inherently led to a situation in current research practice where methods are diverging and integration between individual, team and organizational under...

Experimental validation of a new heterogeneous mechanical test design

Science.gov (United States)

Aquino, J.; Campos, A. Andrade; Souto, N.; Thuillier, S.

2018-05-01

Standard material parameters identification strategies generally use an extensive number of classical tests for collecting the required experimental data. However, a great effort has been made recently by the scientific and industrial communities to support this experimental database on heterogeneous tests. These tests can provide richer information on the material behavior allowing the identification of a more complete set of material parameters. This is a result of the recent development of full-field measurements techniques, like digital image correlation (DIC), that can capture the heterogeneous deformation fields on the specimen surface during the test. Recently, new specimen geometries were designed to enhance the richness of the strain field and capture supplementary strain states. The butterfly specimen is an example of these new geometries, designed through a numerical optimization procedure where an indicator capable of evaluating the heterogeneity and the richness of strain information. However, no experimental validation was yet performed. The aim of this work is to experimentally validate the heterogeneous butterfly mechanical test in the parameter identification framework. For this aim, DIC technique and a Finite Element Model Up-date inverse strategy are used together for the parameter identification of a DC04 steel, as well as the calculation of the indicator. The experimental tests are carried out in a universal testing machine with the ARAMIS measuring system to provide the strain states on the specimen surface. The identification strategy is accomplished with the data obtained from the experimental tests and the results are compared to a reference numerical solution.

The reactor safety study of experimental multi-purpose VHTR design

International Nuclear Information System (INIS)

Yasuno, T.; Mitake, S.; Ezaki, M.; Suzuki, K.

1981-01-01

Over the past years, the design works of the Experimental Very High Temperature Reactor (VHTR) plant have been conducted at Japan Atomic Energy Research Institute. The conceptual design has been completed and the more detailed design works and the safety analysis of the experimental VHTR plant are continued. The purposes of design studies are to show the feasibility of the experimental VHTR program, to specify the characteristics and functions of the plant components, to point out the R and D items necessary for the experimental VHTR plant construction, and to analyze the feature of the plant safety. In this paper the summary of system design and safety features of the experimental reactor are indicated. Main issues are the safety philosophy for the design basis accident, the accidents assumed and the engineered safety systems adopted in the design works

Two polynomial representations of experimental design

OpenAIRE

Notari, Roberto; Riccomagno, Eva; Rogantin, Maria-Piera

2007-01-01

In the context of algebraic statistics an experimental design is described by a set of polynomials called the design ideal. This, in turn, is generated by finite sets of polynomials. Two types of generating sets are mostly used in the literature: Groebner bases and indicator functions. We briefly describe them both, how they are used in the analysis and planning of a design and how to switch between them. Examples include fractions of full factorial designs and designs for mixture experiments.

The influence of the design matrix on treatment effect estimates in the quantitative analyses of single-subject experimental design research.

Science.gov (United States)

Moeyaert, Mariola; Ugille, Maaike; Ferron, John M; Beretvas, S Natasha; Van den Noortgate, Wim

2014-09-01

The quantitative methods for analyzing single-subject experimental data have expanded during the last decade, including the use of regression models to statistically analyze the data, but still a lot of questions remain. One question is how to specify predictors in a regression model to account for the specifics of the design and estimate the effect size of interest. These quantitative effect sizes are used in retrospective analyses and allow synthesis of single-subject experimental study results which is informative for evidence-based decision making, research and theory building, and policy discussions. We discuss different design matrices that can be used for the most common single-subject experimental designs (SSEDs), namely, the multiple-baseline designs, reversal designs, and alternating treatment designs, and provide empirical illustrations. The purpose of this article is to guide single-subject experimental data analysts interested in analyzing and meta-analyzing SSED data. © The Author(s) 2014.

Experimental toxicology: Issues of statistics, experimental design, and replication.

Science.gov (United States)

Briner, Wayne; Kirwan, Jeral

2017-01-01

The difficulty of replicating experiments has drawn considerable attention. Issues with replication occur for a variety of reasons ranging from experimental design to laboratory errors to inappropriate statistical analysis. Here we review a variety of guidelines for statistical analysis, design, and execution of experiments in toxicology. In general, replication can be improved by using hypothesis driven experiments with adequate sample sizes, randomization, and blind data collection techniques. Copyright © 2016 Elsevier B.V. All rights reserved.

Set membership experimental design for biological systems

Directory of Open Access Journals (Sweden)

Marvel Skylar W

2012-03-01

Full Text Available Abstract Background Experimental design approaches for biological systems are needed to help conserve the limited resources that are allocated for performing experiments. The assumptions used when assigning probability density functions to characterize uncertainty in biological systems are unwarranted when only a small number of measurements can be obtained. In these situations, the uncertainty in biological systems is more appropriately characterized in a bounded-error context. Additionally, effort must be made to improve the connection between modelers and experimentalists by relating design metrics to biologically relevant information. Bounded-error experimental design approaches that can assess the impact of additional measurements on model uncertainty are needed to identify the most appropriate balance between the collection of data and the availability of resources. Results In this work we develop a bounded-error experimental design framework for nonlinear continuous-time systems when few data measurements are available. This approach leverages many of the recent advances in bounded-error parameter and state estimation methods that use interval analysis to generate parameter sets and state bounds consistent with uncertain data measurements. We devise a novel approach using set-based uncertainty propagation to estimate measurement ranges at candidate time points. We then use these estimated measurements at the candidate time points to evaluate which candidate measurements furthest reduce model uncertainty. A method for quickly combining multiple candidate time points is presented and allows for determining the effect of adding multiple measurements. Biologically relevant metrics are developed and used to predict when new data measurements should be acquired, which system components should be measured and how many additional measurements should be obtained. Conclusions The practicability of our approach is illustrated with a case study. This

Strain measurement of objects subjected to aerodynamic heating using digital image correlation: experimental design and preliminary results.

Science.gov (United States)

Pan, Bing; Jiang, Tianyun; Wu, Dafang

2014-11-01

In thermomechanical testing of hypersonic materials and structures, direct observation and quantitative strain measurement of the front surface of a test specimen directly exposed to severe aerodynamic heating has been considered as a very challenging task. In this work, a novel quartz infrared heating device with an observation window is designed to reproduce the transient thermal environment experienced by hypersonic vehicles. The specially designed experimental system allows the capture of test article's surface images at various temperatures using an optical system outfitted with a bandpass filter. The captured images are post-processed by digital image correlation to extract full-field thermal deformation. To verify the viability and accuracy of the established system, thermal strains of a chromiumnickel austenite stainless steel sample heated from room temperature up to 600 °C were determined. The preliminary results indicate that the air disturbance between the camera and the specimen due to heat haze induces apparent distortions in the recorded images and large errors in the measured strains, but the average values of the measured strains are accurate enough. Limitations and further improvements of the proposed technique are discussed.

Factorial experimental design intended for the optimization of the alumina purification conditions

Science.gov (United States)

Brahmi, Mounaouer; Ba, Mohamedou; Hidri, Yassine; Hassen, Abdennaceur

2018-04-01

The objective of this study was to determine the optimal conditions by using the experimental design methodology for the removal of some impurities associated with the alumina. So, three alumina qualities of different origins were investigated under the same conditions. The application of full-factorial designs on the samples of different qualities of alumina has followed the removal rates of the sodium oxide. However, a factorial experimental design was developed to describe the elimination of sodium oxide associated with the alumina. The experimental results showed that chemical analyze followed by XRF prior treatment of the samples, provided a primary idea concerning these prevailing impurities. Therefore, it appeared that the sodium oxide constituted the largest amount among all impurities. After the application of experimental design, analysis of the effectors different factors and their interactions showed that to have a better result, we should reduce the alumina quantity investigated and by against increase the stirring time for the first two samples, whereas, it was necessary to increase the alumina quantity in the case of the third sample. To expand and improve this research, we should take into account all existing impurities, since we found during this investigation that the levels of partial impurities increased after the treatment.

Achieving optimal SERS through enhanced experimental design.

Science.gov (United States)

Fisk, Heidi; Westley, Chloe; Turner, Nicholas J; Goodacre, Royston

2016-01-01

One of the current limitations surrounding surface-enhanced Raman scattering (SERS) is the perceived lack of reproducibility. SERS is indeed challenging, and for analyte detection, it is vital that the analyte interacts with the metal surface. However, as this is analyte dependent, there is not a single set of SERS conditions that are universal. This means that experimental optimisation for optimum SERS response is vital. Most researchers optimise one factor at a time, where a single parameter is altered first before going onto optimise the next. This is a very inefficient way of searching the experimental landscape. In this review, we explore the use of more powerful multivariate approaches to SERS experimental optimisation based on design of experiments and evolutionary computational methods. We particularly focus on colloidal-based SERS rather than thin film preparations as a result of their popularity. © 2015 The Authors. Journal of Raman Spectroscopy published by John Wiley & Sons, Ltd.

Dynamic Coefficients of a Tilting Pad With Active Lubrication: Comparison Between Theoretical and Experimental Results

DEFF Research Database (Denmark)

Cerda Varela, Alejandro Javier; Santos, Ilmar

2015-01-01

experimental results from the literature for industrial grade passive tilting pad bearings. This initial validation is followed by a comparison with experimental identification results obtained from a test rig featuring the active bearing design. Good overall agreement is observed in both configurations...

Experimental burn plot trial in the Kruger National Park: history, experimental design and suggestions for data analysis

Directory of Open Access Journals (Sweden)

R. Biggs

2003-12-01

Full Text Available The experimental burn plot (EBP trial initiated in 1954 is one of few ongoing long-termfire ecology research projects in Africa. The trial aims to assess the impacts of differentfire regimes in the Kruger National Park. Recent studies on the EBPs have raised questions as to the experimental design of the trial, and the appropriate model specificationwhen analysing data. Archival documentation reveals that the original design was modified on several occasions, related to changes in the park's fire policy. These modifications include the addition of extra plots, subdivision of plots and changes in treatmentsover time, and have resulted in a design which is only partially randomised. The representativity of the trial plots has been questioned on account of their relatively small size,the concentration of herbivores on especially the frequently burnt plots, and soil variation between plots. It is suggested that these factors be included as covariates inexplanatory models or that certain plots be excluded from data analysis based on resultsof independent studies of these factors. Suggestions are provided for the specificationof the experimental design when analysing data using Analysis of Variance. It is concluded that there is no practical alternative to treating the trial as a fully randomisedcomplete block design.

Zr-Fe-Sn Ternary System Phase Diagrams- New Experimental Results

International Nuclear Information System (INIS)

Nieva, N; Gomez, A; Arias, D

2004-01-01

New experimental results for the Zr-Fe-Sn ternary system are presented in this paper. The phases present and equilibrium relations for the 900 o C isothermal on the central zone of the Gibbs triangle are analysed. A set of ternary alloys was designed and obtained, and they were analysed by semi quantitative SEM- EDS, XRD, and metallographic samples. The resulting ternary phase diagrams are presented here (JCH)

Reference design (MK-I and MK-II) for experimental multi-purpose VHTR

International Nuclear Information System (INIS)

Miyamoto, Yoshiaki; Suzuki, Kunihiko; Sato, Sadao

1975-10-01

This report summarizes the results of a study on thermal and mechanical performances of the core, which are obtained in course of reference design (Mk-I and Mk-II) for the experimental multi-purpose VHTR: (1) Design criteria, design methods and design data. These bases are also discussed in order to refer in the case of proceeding a next design work. (2) The results of performance analysis such as the initial core and its prediction for the irradiated core. (auth.)

Majorana Thermosyphon Prototype Experimental Results

International Nuclear Information System (INIS)

Fast, James E.; Reid, Douglas J.; Aguayo Navarrete, Estanislao

2010-01-01

The Majorana demonstrator will operate at liquid Nitrogen temperatures to ensure optimal spectrometric performance of its High Purity Germanium (HPGe) detector modules. In order to transfer the heat load of the detector module, the Majorana demonstrator requires a cooling system that will maintain a stable liquid nitrogen temperature. This cooling system is required to transport the heat from the detector chamber outside the shield. One approach is to use the two phase liquid-gas equilibrium to ensure constant temperature. This cooling technique is used in a thermosyphon. The thermosyphon can be designed so the vaporization/condensing process transfers heat through the shield while maintaining a stable operating temperature. A prototype of such system has been built at PNNL. This document presents the experimental results of the prototype and evaluates the heat transfer performance of the system. The cool down time, temperature gradient in the thermosyphon, and heat transfer analysis are studied in this document with different heat load applied to the prototype.

Bayesian optimal experimental design for the Shock-tube experiment

International Nuclear Information System (INIS)

Terejanu, G; Bryant, C M; Miki, K

2013-01-01

The sequential optimal experimental design formulated as an information-theoretic sensitivity analysis is applied to the ignition delay problem using real experimental. The optimal design is obtained by maximizing the statistical dependence between the model parameters and observables, which is quantified in this study using mutual information. This is naturally posed in the Bayesian framework. The study shows that by monitoring the information gain after each measurement update, one can design a stopping criteria for the experimental process which gives a minimal set of experiments to efficiently learn the Arrhenius parameters.

A belt charging system for the Vivitron - design, early results

International Nuclear Information System (INIS)

Helleboid, J.M.; Gaudiot, G.

1990-10-01

A specific belt charging system has been designed, built and assembled for the 35 MV Vivitron. 100 m long belt is used. Together with main features of the design, experimental studies, tests in a pilot machine and the results of the very early tests of the real system are reviewed

On the construction of experimental designs for a given task by jointly optimizing several quality criteria: Pareto-optimal experimental designs.

Science.gov (United States)

Sánchez, M S; Sarabia, L A; Ortiz, M C

2012-11-19

Experimental designs for a given task should be selected on the base of the problem being solved and of some criteria that measure their quality. There are several such criteria because there are several aspects to be taken into account when making a choice. The most used criteria are probably the so-called alphabetical optimality criteria (for example, the A-, E-, and D-criteria related to the joint estimation of the coefficients, or the I- and G-criteria related to the prediction variance). Selecting a proper design to solve a problem implies finding a balance among these several criteria that measure the performance of the design in different aspects. Technically this is a problem of multi-criteria optimization, which can be tackled from different views. The approach presented here addresses the problem in its real vector nature, so that ad hoc experimental designs are generated with an algorithm based on evolutionary algorithms to find the Pareto-optimal front. There is not theoretical limit to the number of criteria that can be studied and, contrary to other approaches, no just one experimental design is computed but a set of experimental designs all of them with the property of being Pareto-optimal in the criteria needed by the user. Besides, the use of an evolutionary algorithm makes it possible to search in both continuous and discrete domains and avoid the need of having a set of candidate points, usual in exchange algorithms. Copyright © 2012 Elsevier B.V. All rights reserved.

Fast Bayesian optimal experimental design and its applications

KAUST Repository

Long, Quan

2015-01-07

We summarize our Laplace method and multilevel method of accelerating the computation of the expected information gain in a Bayesian Optimal Experimental Design (OED). Laplace method is a widely-used method to approximate an integration in statistics. We analyze this method in the context of optimal Bayesian experimental design and extend this method from the classical scenario, where a single dominant mode of the parameters can be completely-determined by the experiment, to the scenarios where a non-informative parametric manifold exists. We show that by carrying out this approximation the estimation of the expected Kullback-Leibler divergence can be significantly accelerated. While Laplace method requires a concentration of measure, multi-level Monte Carlo method can be used to tackle the problem when there is a lack of measure concentration. We show some initial results on this approach. The developed methodologies have been applied to various sensor deployment problems, e.g., impedance tomography and seismic source inversion.

Optimizing laboratory animal stress paradigms: The H-H* experimental design.

Science.gov (United States)

McCarty, Richard

2017-01-01

Major advances in behavioral neuroscience have been facilitated by the development of consistent and highly reproducible experimental paradigms that have been widely adopted. In contrast, many different experimental approaches have been employed to expose laboratory mice and rats to acute versus chronic intermittent stress. An argument is advanced in this review that more consistent approaches to the design of chronic intermittent stress experiments would provide greater reproducibility of results across laboratories and greater reliability relating to various neural, endocrine, immune, genetic, and behavioral adaptations. As an example, the H-H* experimental design incorporates control, homotypic (H), and heterotypic (H*) groups and allows for comparisons across groups, where each animal is exposed to the same stressor, but that stressor has vastly different biological and behavioral effects depending upon each animal's prior stress history. Implementation of the H-H* experimental paradigm makes possible a delineation of transcriptional changes and neural, endocrine, and immune pathways that are activated in precisely defined stressor contexts. Copyright © 2016 Elsevier Ltd. All rights reserved.

Design, construction and testing of a radon experimental chamber

International Nuclear Information System (INIS)

Chavez B, A.; Balcazar G, M.

1991-10-01

To carry out studies on the radon behavior under controlled and stable conditions it was designed and constructed a system that consists of two parts: a container of mineral rich in Uranium and an experimentation chamber with radon united one to the other one by a step valve. The container of uranium mineral approximately contains 800 gr of uranium with a law of 0.28%; the radon gas emanated by the mineral is contained tightly by the container. When the valve opens up the radon gas it spreads to the radon experimental chamber; this contains 3 accesses that allow to install different types of detectors. The versatility of the system is exemplified with two experiments: 1. With the radon experimental chamber and an associated spectroscopic system, the radon and two of its decay products are identified. 2. The design of the system allows to couple the mineral container to other experimental geometries to demonstrate this fact it was coupled and proved a new automatic exchanger system of passive detectors of radon. The results of the new automatic exchanger system when it leave to flow the radon freely among the container and the automatic exchanger through a plastic membrane of 15 m. are shown. (Author)

Conceptual design study of Fusion Experimental Reactor (FY87FER)

International Nuclear Information System (INIS)

1988-05-01

The design study of Fusion Experimental Reactor(FER) which has been proposed to be the next step fusion device has been conducted by JAERI Reactor System Laboratory since 1982 and by FER design team since 1984. This is the final report of the FER design team program and describes the results obtained in FY1987 (partially in FY1986) activities. The contents of this report consist of the reference design which is based on the guideline in FY1986 by the Subcomitees set up in Nuclear Fusion Council of Atomic Energy Commission of Japan, the Low-Physics-Risk reactor design for achieving physics mission more reliably and the system study of FER design candidates including above two designs. (author)

Computations for a condenser. Experimental results

International Nuclear Information System (INIS)

Walden, Jean.

1975-01-01

Computations for condensers are presented with experimental results. The computations are concerned with the steam flux at the condenser input, and inside the tube bundle. Experimental results are given for the flux inside the condenser sleeve and the flow passing through the tube bundle [fr

Research Methods in Healthcare Epidemiology and Antimicrobial Stewardship-Quasi-Experimental Designs.

Science.gov (United States)

Schweizer, Marin L; Braun, Barbara I; Milstone, Aaron M

2016-10-01

Quasi-experimental studies evaluate the association between an intervention and an outcome using experiments in which the intervention is not randomly assigned. Quasi-experimental studies are often used to evaluate rapid responses to outbreaks or other patient safety problems requiring prompt, nonrandomized interventions. Quasi-experimental studies can be categorized into 3 major types: interrupted time-series designs, designs with control groups, and designs without control groups. This methods paper highlights key considerations for quasi-experimental studies in healthcare epidemiology and antimicrobial stewardship, including study design and analytic approaches to avoid selection bias and other common pitfalls of quasi-experimental studies. Infect Control Hosp Epidemiol 2016;1-6.

Feedback control of a cupola - concepts and experimental results

Energy Technology Data Exchange (ETDEWEB)

Moore, K.L. [Idaho State Univ., Pocatello, ID (United States); Abdelrahman, M.A. [Tenn. Technological Univ., Cookeville, TN (United States); Larsen, E.; Clark, D. [Lockheed Martin Idaho Technologies Co., Idaho Falls, ID (United States); King, P. [US Dept. of Energy Albany Research Center, Albany, OR (United States)

1998-10-01

In this paper we present some final results from a research project focused on introducing automatic control to the operation of cupola iron furnaces. The main aim of this research is to improve the operational efficiency and performance of the cupola furnace, an important foundry process used to melt iron. Previous papers have described the development of appropriate control system architectures for the cupola. These results are summarized. Then we describe the experimental results obtained with the U.S. Department of Energy Albany Research Center`s research cupola. First, experimental data is used to calibrate the model, which is taken as a first-order multivariable system with time delay. Then relative gain analysis is used to select loop pairings to be used in a multi-loop controller. The resulting controller pairs meltrate with blast volume, iron temperature with oxygen addition, and carbon composition with percent coke. Special (nonlinear) filters are used to compute meltrate from actual scale readings of the amount of iron produced and to smooth the temperature measurement. The temperature and meltrate loops use single-loop PI control. The composition loop uses a Smith predictor to discount the deadtime associated with mass transport through the furnace. Experimental results validate the conceptual controller design and provide proof-of-concept of the idea of controlling a foundry cupola. Future research directions are discussed, including the concept of an integrated, intelligent industrial process controller, or I{sup 3}PC.

Revised design for the Tokamak experimental power reactor

International Nuclear Information System (INIS)

Stacey, W.M. Jr.; Abdou, M.A.; Brooks, J.N.

1977-03-01

A new, preliminary design has been identified for the tokamak experimental power reactor (EPR). The revised EPR design is simpler, more compact, less expensive and has somewhat better performance characteristics than the previous design, yet retains many of the previously developed design concepts. This report summarizes the principle features of the new EPR design, including performance and cost

Publishing Single-Case Research Design Studies That Do Not Demonstrate Experimental Control

Science.gov (United States)

Tincani, Matt; Travers, Jason

2018-01-01

Demonstration of experimental control is considered a hallmark of high-quality single-case research design (SCRD). Studies that fail to demonstrate experimental control may not be published because researchers are unwilling to submit these papers for publication and journals are unlikely to publish negative results (i.e., the file drawer effect).…

Development of the Biological Experimental Design Concept Inventory (BEDCI)

Science.gov (United States)

Deane, Thomas; Nomme, Kathy; Jeffery, Erica; Pollock, Carol; Birol, Gulnur

2014-01-01

Interest in student conception of experimentation inspired the development of a fully validated 14-question inventory on experimental design in biology (BEDCI) by following established best practices in concept inventory (CI) design. This CI can be used to diagnose specific examples of non-expert-like thinking in students and to evaluate the…

Conceptual design of helium experimental loop

International Nuclear Information System (INIS)

Yu Xingfu; Feng Kaiming

2007-01-01

In a future demonstration fusion power station (DEMO), helium is envisaged as coolant for plasma facing components, such as blanket and dive,or. All these components have a very complex geometry, with many parallel cooling channels, involving a complex helium flow distribution. Test blanket modules (TBM) of this concept will under go various tests in the experimental reactor ITER. For the qualification of TBM, it is indispensable to test mock-ups in a helium loop under realistic pressure and temperature profiles, in order to validate design codes, especially regarding mass flow and heat transition processes in narrow cooling channels. Similar testing must be performed for DEMO blanket, currently under development. A Helium Experimental Loop (HELOOP) is planed to be built for TBM tests. The design parameter of temperature, pressure, flow rate is 550 degree C, 10 MPa, l kg/s respectively. In particular, HELOOP is able to: perform full-scale tests of TBM under realistic conditions; test other components of the He-cooling system in ITER; qualify the purification circuit; obtain information for the design of the ITER cooling system. The main requirements and characteristics of the HELOOP facility and a preliminary conceptual design are described in the paper. (authors)

Design of Passive Acoustic Wave Shaping Devices and Their Experimental Validation

DEFF Research Database (Denmark)

Christiansen, Rasmus Ellebæk; Sigmund, Ole; Fernandez Grande, Efren

We discuss a topology optimization based approach for designing passive acoustic wave shaping devices and demonstrate its application to; directional sound emission [1], sound focusing and wave splitting. Optimized devices, numerical and experimental results are presented and benchmarked against...... other designs proposed in the literature. We focus on design problems where the size of the device is on the order of the wavelength, a problematic region for traditional design methods, such as ray tracing.The acoustic optimization problem is formulated in the frequency domain and modeled...

Experimental results on the design for the APS PID global orbit control system

International Nuclear Information System (INIS)

Chung, Y.; Kirchman, J. A.

1997-01-01

The Advanced Photon Source third generation synchrotrons light source needs a stabilized particle beam position to produce high brightness and low emittance radiation. Global orbit correction control is introduced and is utilized to satisfy the demanding needs of the accelerator. This paper presents the experimental results for determining an effective and optimal controller to meet the global orbit correction requirements. These requirements include frequency/time domain demands consisting of vibrational noise attenuation, limiting of controller gains for stability and improving the system time response. Experiments were conducted with a digital signal processor implementing various PID sets to make comparisons between simulations and experiments. Measurements at these PID sets supported the results of software simulation

Validation of Code ASTEC with LIVE-L1 Experimental Results

International Nuclear Information System (INIS)

Bachrata, Andrea

2008-01-01

The severe accidents with core melting are considered at the design stage of project at Generation 3+ of Nuclear Power Plants (NPP). Moreover, there is an effort to apply the severe accident management to the operated NPP. The one of main goals of severe accidents mitigation is corium localization and stabilization. The two strategies that fulfil this requirement are: the in-vessel retention (e.g. AP-600, AP- 1000) and the ex-vessel retention (e.g. EPR). To study the scenario of in-vessel retention, a large experimental program and the integrated codes have been developed. The LIVE-L1 experimental facility studied the formation of melt pools and the melt accumulation in the lower head using different cooling conditions. Nowadays, a new European computer code ASTEC is being developed jointly in France and Germany. One of the important steps in ASTEC development in the area of in-vessel retention of corium is its validation with LIVE-L1 experimental results. Details of the experiment are reported. Results of the ASTEC (module DIVA) application to the analysis of the test are presented. (author)

Neural Network Assisted Experimental Designs for Food Research

Directory of Open Access Journals (Sweden)

H.S. Ramaswamy

2000-06-01

Full Text Available The ability of artificial neural networks (ANN in predicting full factorial data from the fractional data corresponding to some of the commonly used experimental designs is explored in this paper. Factorial and fractional factorial designs such as L8, L9, L18, and Box and Behnken schemes were considered both in their original form and with some variations (L8+6, L15 and L9+1. Full factorial (3 factors x 5 levels and fractional data were generated employing sixteen different mathematical equations (four in each category: linear, with and without interactions, and non-linear, with and without interactions. Different ANN models were trained and the best model was chosen for each equation based on their ability to predict the fractional data. The best experimental design was then chosen based on their ability to simulate the full- factorial data for each equation. In several cases, the mean relative errors with the L18 design (which had more input data than other models were even higher than with other smaller fractional design. In general, the ANN assisted Lm, Box and Behnken, L15 and L18 designs were found to predict the full factorial data reasonably well with errors less than 5 %. The L8+6 model performed well with several experimental datasets reported in the literature.

Experimental designs for autoregressive models applied to industrial maintenance

International Nuclear Information System (INIS)

Amo-Salas, M.; López-Fidalgo, J.; Pedregal, D.J.

2015-01-01

Some time series applications require data which are either expensive or technically difficult to obtain. In such cases scheduling the points in time at which the information should be collected is of paramount importance in order to optimize the resources available. In this paper time series models are studied from a new perspective, consisting in the use of Optimal Experimental Design setup to obtain the best times to take measurements, with the principal aim of saving costs or discarding useless information. The model and the covariance function are expressed in an explicit form to apply the usual techniques of Optimal Experimental Design. Optimal designs for various approaches are computed and their efficiencies are compared. The methods working in an application of industrial maintenance of a critical piece of equipment at a petrochemical plant are shown. This simple model allows explicit calculations in order to show openly the procedure to find the correlation structure, needed for computing the optimal experimental design. In this sense the techniques used in this paper to compute optimal designs may be transferred to other situations following the ideas of the paper, but taking into account the increasing difficulty of the procedure for more complex models. - Highlights: • Optimal experimental design theory is applied to AR models to reduce costs. • The first observation has an important impact on any optimal design. • Either the lack of precision or small starting observations claim for large times. • Reasonable optimal times were obtained relaxing slightly the efficiency. • Optimal designs were computed in a predictive maintenance context

Experimental design techniques in statistical practice a practical software-based approach

CERN Document Server

Gardiner, W P

1998-01-01

Provides an introduction to the diverse subject area of experimental design, with many practical and applicable exercises to help the reader understand, present and analyse the data. The pragmatic approach offers technical training for use of designs and teaches statistical and non-statistical skills in design and analysis of project studies throughout science and industry. Provides an introduction to the diverse subject area of experimental design and includes practical and applicable exercises to help understand, present and analyse the data Offers technical training for use of designs and teaches statistical and non-statistical skills in design and analysis of project studies throughout science and industry Discusses one-factor designs and blocking designs, factorial experimental designs, Taguchi methods and response surface methods, among other topics.

Research Methods in Healthcare Epidemiology and Antimicrobial Stewardship – Quasi-Experimental Designs

Science.gov (United States)

Schweizer, Marin L.; Braun, Barbara I.; Milstone, Aaron M.

2016-01-01

Quasi-experimental studies evaluate the association between an intervention and an outcome using experiments in which the intervention is not randomly assigned. Quasi-experimental studies are often used to evaluate rapid responses to outbreaks or other patient safety problems requiring prompt non-randomized interventions. Quasi-experimental studies can be categorized into three major types: interrupted time series designs, designs with control groups, and designs without control groups. This methods paper highlights key considerations for quasi-experimental studies in healthcare epidemiology and antimicrobial stewardship including study design and analytic approaches to avoid selection bias and other common pitfalls of quasi-experimental studies. PMID:27267457

An Experimental Design of Bypass Magneto-Rheological (MR) damper

Science.gov (United States)

Rashid, MM; Aziz, Mohammad Abdul; Raisuddin Khan, Md.

2017-11-01

The magnetorheological (MR) fluid bypass damper fluid flow through a bypass by utilizing an external channel which allows the controllability of MR fluid in the channel. The Bypass MR damper (BMRD) contains a rectangular bypass flow channel, current controlled movable piston shaft arrangement and MR fluid. The static piston coil case is winding by a coil which is used inside the piston head arrangement. The current controlled coil case provides a magnetic flux through the BMRD cylinder for controllability. The high strength of alloy steel materials are used for making piston shaft which allows magnetic flux propagation throughout the BMRD cylinder. Using the above design materials, a Bypass MR damper is designed and tested. An excitation of current is applied during the experiment which characterizes the BMRD controllability. It is shown that the BMRD with external flow channel allows a high controllable damping force using an excitation current. The experimental result of damping force-displacement characteristics with current excitation and without current excitation are compared in this research. The BMRD model is validated by the experimental result at various frequencies and applied excitation current.

Design activities of a fusion experimental breeder

International Nuclear Information System (INIS)

Huang, J.; Feng, K.; Sheng, G.

1999-01-01

The fusion reactor design studies in China are under the support of a fusion-fission hybrid reactor research Program. The purpose of this program is to explore the potential near-term application of fusion energy to support the long-term fusion energy on the one hand and the fission energy development on the other. During 1992-1996 a detailed consistent and integral conceptual design of a Fusion Experimental Breeder, FEB was completed. Beginning from 1996, a further design study towards an Engineering Outline Design of the FEB, FEB-E, has started. The design activities are briefly given. (author)

Design activities of a fusion experimental breeder

International Nuclear Information System (INIS)

Huang, J.; Feng, K.; Sheng, G.

2001-01-01

The fusion reactor design studies in China are under the support of a fusion-fission hybrid reactor research Program. The purpose of this program is to explore the potential near-term application of fusion energy to support the long-term fusion energy on the one hand and the fission energy development on the other. During 1992-1996 a detailed consistent and integral conceptual design of a Fusion Experimental Breeder, FEB was completed. Beginning from 1996, a further design study towards an Engineering Outline Design of the FEB, FEB-E, has started. The design activities are briefly given. (author)

An Introduction to Experimental Design Research

DEFF Research Database (Denmark)

Cash, Philip; Stanković, Tino; Štorga, Mario

2016-01-01

Design research brings together influences from the whole gamut of social, psychological, and more technical sciences to create a tradition of empirical study stretching back over 50 years (Horvath 2004; Cross 2007). A growing part of this empirical tradition is experimental, which has gained in ...

Advanced Supersonic Nozzle Concepts: Experimental Flow Visualization Results Paired With LES

Science.gov (United States)

Berry, Matthew; Magstadt, Andrew; Stack, Cory; Gaitonde, Datta; Glauser, Mark; Syracuse University Team; The Ohio State University Team

2015-11-01

Advanced supersonic nozzle concepts are currently under investigation, utilizing multiple bypass streams and airframe integration to bolster performance and efficiency. This work focuses on the parametric study of a supersonic, multi-stream jet with aft deck. The single plane of symmetry, rectangular nozzle, displays very complex and unique flow characteristics. Flow visualization techniques in the form of PIV and schlieren capture flow features at various deck lengths and Mach numbers. LES is compared to the experimental results to both validate the computational model and identify limitations of the simulation. By comparing experimental results to LES, this study will help create a foundation of knowledge for advanced nozzle designs in future aircraft. SBIR Phase II with Spectral Energies, LLC under direction of Barry Kiel.

Conceptual design study of fusion experimental reactor (FER)

International Nuclear Information System (INIS)

1986-11-01

Since 1980 the design study has been conducted at JAERI for the Fusion Experimental Reactor (FER) which has been proposed to be the next machine to JT-60 in the Japanese long term program of fusion reactor development. During two years from 1984 to 1985 FER concept was reviewed and redesigned. This report is the summary of the results obtained in the review and redesign activities in 1984 and 85. In the first year FER concept was discussed again and its frame work was reestablished. According to the new frame work the major reactor components of FER were designed. In the second year the whole plant system design including plant layout plan was conducted as well as the more detailed design analysis of the reactor conponents. The newly established frame for FER design is as follows: 1) Plasma : Self-ignition. 2) Operation scenario : Quasi-steady state operation with long burn pulse. 3) Neutron fluence on the first wall : 0.3 MWY/M 2 . 4) Blanket : Non-tritium breeding blanket with test modules for breeding blanket development. 5) Magnets : Superconducting Magnets. (author)

Experimental use of iteratively designed rotation invariant correlation filters

International Nuclear Information System (INIS)

Sweeney, D.W.; Ochoa, E.; Schils, G.F.

1987-01-01

Iteratively designed filters are incorporated into an optical correlator for position, rotation, and intensity invariant recognition of target images. The filters exhibit excellent discrimination because they are designed to contain full information about the target image. Numerical simulations and experiments demonstrate detection of targets that are corrupted with random noise (SNR≅0.5) and also partially obscured by other objects. The complex valued filters are encoded in a computer generated hologram and fabricated directly using an electron-beam system. Experimental results using a liquid crystal spatial light modulator for real-time input show excellent agreement with analytical and numerical computations

Mixed-mode chaotic circuit with Wien-bridge configuration: The results of experimental verification

International Nuclear Information System (INIS)

Kilic, Recai

2007-01-01

In this paper, we deal with the experimentally implementation of inductorless Wien bridge-based mixed-mode chaotic circuit (MMCC) which is capable to exhibit both linear and nonlinear oscillations. The results of experimental implementation agree with the results of theoretical and computer simulation presented in literature. Since the proposed implementation of MMCC circuit uses different design blocks such as Wien bridge-based autonomous circuit part, CFOA (current feedback operational amplifier)-based floating inductance simulator, CFOA-based Chua's diode and switching mechanism, it offers very versatile chaotic circuit model for studying autonomous and nonautonomous chaotic dynamics

Status of experimental data for the VHTR core design

Energy Technology Data Exchange (ETDEWEB)

Park, Won Seok; Chang, Jong Hwa; Park, Chang Kue

2004-05-01

The VHTR (Very High Temperature Reactor) is being emerged as a next generation nuclear reactor to demonstrate emission-free nuclear-assisted electricity and hydrogen production. The VHTR could be either a prismatic or pebble type helium cooled, graphite moderated reactor. The final decision will be made after the completion of the pre-conceptual design for each type. For the pre-conceptual design for both types, computational tools are being developed. Experimental data are required to validate the tools to be developed. Many experiments on the HTGR (High Temperature Gas-cooled Reactor) cores have been performed to confirm the design data and to validate the design tools. The applicability and availability of the existing experimental data have been investigated for the VHTR core design in this report.

Design of JT-60SA magnets and associated experimental validations

International Nuclear Information System (INIS)

Zani, L.; Barabaschi, P.; Peyrot, M.; Meunier, L.; Tomarchio, V.; Duglue, D.; Decool, P.; Torre, A.; Marechal, J.L.; Della Corte, A.; Di Zenobio, A.; Muzzi, L.; Cucchiaro, A.; Turtu, S.; Ishida, S.; Yoshida, K.; Tsuchiya, K.; Kizu, K.; Murakami, H.

2011-01-01

In the framework of the JT-60SA project, aiming at upgrading the present JT-60U tokamak toward a fully superconducting configuration, the detailed design phase led to adopt for the three main magnet systems a brand new design. Europe (EU) is expected to provide to Japan (JA) the totality of the toroidal field (TF) magnet system, while JA will provide both Equilibrium field (EF) and Central Solenoid (CS) systems. All magnet designs were optimized trough the past years and entered in parallel into extensive experimentally-based phases of concept validation, which came to maturation in the years 2009 and 2010. For this, all magnet systems were investigated by mean of dedicated samples, e.g. conductor and joint samples designed, manufactured and tested at full scale in ad hoc facilities either in EU or in JA. The present paper, after an overall description of magnet systems layouts, presents in a general approach the different experimental campaigns dedicated to qualification design and manufacture processes of either coils, conductors and electrical joints. The main results with the associated analyses are shown and the main conclusions presented, especially regarding their contribution to consolidate the triggering of magnet mass production. The status of respective manufacturing stages in EU and in JA are also evoked. (authors)

Statistical experimental design for saltstone mixtures

International Nuclear Information System (INIS)

Harris, S.P.; Postles, R.L.

1991-01-01

We used a mixture experimental design for determining a window of operability for a process at the Savannah River Site Defense Waste Processing Facility (DWPF). The high-level radioactive waste at the Savannah River Site is stored in large underground carbon steel tanks. The waste consists of a supernate layer and a sludge layer. 137 Cs will be removed from the supernate by precipitation and filtration. After further processing, the supernate layer will be fixed as a grout for disposal in concrete vaults. The remaining precipitate will be processed at the DWPF with treated waste tank sludge and glass-making chemicals into borosilicate glass. The leach rate properties of the supernate grout, formed from various mixes of solidified salt waste, needed to be determined. The effective diffusion coefficients for NO 3 and Cr were used as a measure of leach rate. Various mixes of cement, Ca(OH) 2 , salt, slag and flyash were used. These constituents comprise the whole mix. Thus, a mixture experimental design was used

Experimental site and design

Energy Technology Data Exchange (ETDEWEB)

Guenette, C. C. [SINTEF Applied Cemistry, Trondheim (Norway)

1999-08-01

Design and site selection criteria for the Svalbard oil spill experiments are described. All three experimental sites have coarse and mixed sediment beaches of sand and pebble; within each site wave exposure is very similar; along-shore and across-shore sediment characteristics are also relatively homogeneous. Tidal range is in the order of 0.6 m at neaps, and 1.8 m at springs. All three sites are open to wave action and are ice-free during the experimental period of mid-July to mid-October. Study plots at each site were selected for different treatments from within the continuous stretch of oiled shoreline, with oiled buffer zones between plots and at either end of the oiled zone. Treatments included mixing (tilling), sediment relocation (surf washing) and bioremediation (nutrient enrichment). Measurements and observations were carried out during the summers of 1997 and 1998. The characteristics measured were: wave and wind conditions; beach topography and elevation; sediment grain size distribution; mineral fines size distribution and mineral composition; background hydrocarbons; concentration of oil within experimental plots and the rate of oil loss over time; depth of oil penetration and thickness of the oiled sediment layer; oil concentration and toxicity of near-shore benthic sediments; mineral composition of suspended particulate material captured in sub-tidal sediment traps; and oil-fines interaction in near-shore water samples. 1 fig.

Experimental site and design

Energy Technology Data Exchange (ETDEWEB)

Guenette, C. C. [SINTEF Applied Cemistry, Trondheim (Norway)

1999-07-01

Design and site selection criteria for the Svalbard oil spill experiments are described. All three experimental sites have coarse and mixed sediment beaches of sand and pebble; within each site waveexposure is very similar; along-shore and across-shore sediment characteristics are also relatively homogeneous. Tidal range is in the order of 0.6 m at neaps, and 1.8 m at springs. All three sites are open to wave action and are ice-free during the experimental period of mid-July to mid-October. Study plots at each site were selected for different treatments from within the continuous stretch of oiled shoreline, with oiled buffer zones between plots and at either end of the oiled zone. Treatments included mixing (tilling), sediment relocation (surf washing) and bioremediation (nutrient enrichment). Measurements and observations were carried out during the summers of 1997 and 1998. The characteristics measured were: wave and wind conditions; beach topography and elevation; sediment grain size distribution; mineral fines size distribution and mineral composition; background hydrocarbons; concentration of oil within experimental plots and the rate of oil loss over time; depth of oil penetration and thickness of the oiled sediment layer; oil concentration and toxicity of near-shore benthic sediments; mineral composition of suspended particulate material captured in sub-tidal sediment traps; and oil-fines interaction in near-shore water samples. 1 fig.

Experimental results for a novel rotary active magnetic regenerator

DEFF Research Database (Denmark)

Engelbrecht, Kurt; Eriksen, Dan; Bahl, Christian

2012-01-01

Active magnetic regenerator (AMR) refrigerators represent an alternative to vapor compression technology and have great potential in realizing cooling devices with high efficiency, which are highly desirable for a broad range of applications. The technology relies on the magnetocaloric effect...... in a solid refrigerant rather than the temperature change that occurs when a gas is compressed/expanded. This paper presents the general considerations for the design and construction of a high frequency rotary AMR device. Experimental results are presented at various cooling powers for a range of operating...

Tritium system design studies of fusion experimental breeder

International Nuclear Information System (INIS)

Deng Baiquan; Huang Jinhua

2003-01-01

A summary of the tritium system design studies for the engineering outline design of a fusion experimental breeder (FEB-E) is presented. This paper is divided into three sections. In first section, the geometry, loading features and tritium concentrations in liquid lithium of tritium breeding zones of blanket are described. The tritium flow chart corresponding to the tritium fuel cycle system has been constructed, and the inventories in ten subsystems are calculated using SWITRIM code in section 2. Results show that the necessary initial tritium storage to start up FEB-E with fusion power of 143 MW is about 319 g. In final section, the tritium leakage issues under different operation circumstances have been analyzed. It was found that the potential danger of tritium leakage could be resulted from the exhausted gas of the diverter system. It is important to elevate the tritium burnup fraction and reduce the tritium throughput. (authors)

Entropy-Based Experimental Design for Optimal Model Discrimination in the Geosciences

Directory of Open Access Journals (Sweden)

Wolfgang Nowak

2016-11-01

Full Text Available Choosing between competing models lies at the heart of scientific work, and is a frequent motivation for experimentation. Optimal experimental design (OD methods maximize the benefit of experiments towards a specified goal. We advance and demonstrate an OD approach to maximize the information gained towards model selection. We make use of so-called model choice indicators, which are random variables with an expected value equal to Bayesian model weights. Their uncertainty can be measured with Shannon entropy. Since the experimental data are still random variables in the planning phase of an experiment, we use mutual information (the expected reduction in Shannon entropy to quantify the information gained from a proposed experimental design. For implementation, we use the Preposterior Data Impact Assessor framework (PreDIA, because it is free of the lower-order approximations of mutual information often found in the geosciences. In comparison to other studies in statistics, our framework is not restricted to sequential design or to discrete-valued data, and it can handle measurement errors. As an application example, we optimize an experiment about the transport of contaminants in clay, featuring the problem of choosing between competing isotherms to describe sorption. We compare the results of optimizing towards maximum model discrimination with an alternative OD approach that minimizes the overall predictive uncertainty under model choice uncertainty.

System design overview of JAXA small supersonic experimental airplane (NEXST-1)

OpenAIRE

Takami, Hikaru; 高見　光

2007-01-01

The system of JAXA small supersonic experimental airplane (NEXST-1: National EXperimental Supersonic Transport-1) has been briefly explained. Some design problems that the designers have encountered have also been briefly explained.

Quasi-experimental study designs series-paper 7: assessing the assumptions.

Science.gov (United States)

Bärnighausen, Till; Oldenburg, Catherine; Tugwell, Peter; Bommer, Christian; Ebert, Cara; Barreto, Mauricio; Djimeu, Eric; Haber, Noah; Waddington, Hugh; Rockers, Peter; Sianesi, Barbara; Bor, Jacob; Fink, Günther; Valentine, Jeffrey; Tanner, Jeffrey; Stanley, Tom; Sierra, Eduardo; Tchetgen, Eric Tchetgen; Atun, Rifat; Vollmer, Sebastian

2017-09-01

Quasi-experimental designs are gaining popularity in epidemiology and health systems research-in particular for the evaluation of health care practice, programs, and policy-because they allow strong causal inferences without randomized controlled experiments. We describe the concepts underlying five important quasi-experimental designs: Instrumental Variables, Regression Discontinuity, Interrupted Time Series, Fixed Effects, and Difference-in-Differences designs. We illustrate each of the designs with an example from health research. We then describe the assumptions required for each of the designs to ensure valid causal inference and discuss the tests available to examine the assumptions. Copyright © 2017 Elsevier Inc. All rights reserved.

Optimal Experimental Design for Model Discrimination

Science.gov (United States)

Myung, Jay I.; Pitt, Mark A.

2009-01-01

Models of a psychological process can be difficult to discriminate experimentally because it is not easy to determine the values of the critical design variables (e.g., presentation schedule, stimulus structure) that will be most informative in differentiating them. Recent developments in sampling-based search methods in statistics make it…

Application of Iterative Robust Model-based Optimal Experimental Design for the Calibration of Biocatalytic Models

DEFF Research Database (Denmark)

Van Daele, Timothy; Gernaey, Krist V.; Ringborg, Rolf Hoffmeyer

2017-01-01

The aim of model calibration is to estimate unique parameter values from available experimental data, here applied to a biocatalytic process. The traditional approach of first gathering data followed by performing a model calibration is inefficient, since the information gathered during...... experimentation is not actively used to optimise the experimental design. By applying an iterative robust model-based optimal experimental design, the limited amount of data collected is used to design additional informative experiments. The algorithm is used here to calibrate the initial reaction rate of an ω......-transaminase catalysed reaction in a more accurate way. The parameter confidence region estimated from the Fisher Information Matrix is compared with the likelihood confidence region, which is a more accurate, but also a computationally more expensive method. As a result, an important deviation between both approaches...

Training reactor deployment. Advanced experimental course on designing new reactor cores

International Nuclear Information System (INIS)

Skoda, Radek

2009-01-01

Czech Technical University in Prague (CTU) operating its training nuclear reactor VR1, in cooperation with the North West University of South Africa (NWU), is applying for accreditation of the experimental training course ''Advanced experimental course on designing the new reactor core'' that will guide the students, young nuclear engineering professionals, through designing, calculating, approval, and assembling a new nuclear reactor core. Students, young professionals from the South African nuclear industry, face the situation when a new nuclear reactor core is to be build from scratch. Several reactor core design options are pre-calculated. The selected design is re-calculated by the students, the result is then scrutinized by the regulator and, once all the analysis is approved, physical dismantling of the current core and assembling of the new core is done by the students, under a close supervision of the CTU staff. Finally the reactor is made critical with the new core. The presentation focuses on practical issues of such a course, desired reactor features and namely pedagogical and safety aspects. (orig.)

Mixed-mode chaotic circuit with Wien-bridge configuration: The results of experimental verification

Energy Technology Data Exchange (ETDEWEB)

Kilic, Recai [Erciyes University, Department of Electronic Engineering, 38039 Kayseri (Turkey)]. E-mail: kilic@erciyes.edu.tr

2007-05-15

In this paper, we deal with the experimentally implementation of inductorless Wien bridge-based mixed-mode chaotic circuit (MMCC) which is capable to exhibit both linear and nonlinear oscillations. The results of experimental implementation agree with the results of theoretical and computer simulation presented in literature. Since the proposed implementation of MMCC circuit uses different design blocks such as Wien bridge-based autonomous circuit part, CFOA (current feedback operational amplifier)-based floating inductance simulator, CFOA-based Chua's diode and switching mechanism, it offers very versatile chaotic circuit model for studying autonomous and nonautonomous chaotic dynamics.

FIRST EXPERIMENTAL RESULTS FROM DEGAS, THE QUANTUM LIMITED BRIGHTNESS ELECTRON SOURCE

International Nuclear Information System (INIS)

Zolotorev, Max S.; Commins, Eugene D.; Oneill, James; Sannibale, Fernando; Tremsin, Anton; Wan, Weishi

2008-01-01

The construction of DEGAS (DEGenerate Advanced Source), a proof of principle for a quantum limited brightness electron source, has been completed at the Lawrence Berkeley National Laboratory. The commissioning and the characterization of this source, designed to generate coherent single electron 'bunches' with brightness approaching the quantum limit at a repetition rate of few MHz, has been started. In this paper the first experimental results are described

Using IMPRINT to Guide Experimental Design with Simulated Task Environments

Science.gov (United States)

2015-06-18

USING IMPRINT TO GUIDE EXPERIMENTAL DESIGN OF SIMULATED TASK ENVIRONMENTS THESIS Gregory...ENG-MS-15-J-052 USING IMPRINT TO GUIDE EXPERIMENTAL DESIGN WITH SIMULATED TASK ENVIRONMENTS THESIS Presented to the Faculty Department...Civilian, USAF June 2015 DISTRIBUTION STATEMENT A. APPROVED FOR PUBLIC RELEASE; DISTRIBUTION UNLIMITED. AFIT-ENG-MS-15-J-052 USING IMPRINT

Exploring multi-metal biosorption by indigenous metal-hyperresistant Enterobacter sp. J1 using experimental design methodologies

International Nuclear Information System (INIS)

Lu, W.-B.; Kao, W.-C.; Shi, J.-J.; Chang, J.-S.

2008-01-01

A novel experimental design, combining mixture design and response surface methodology (RSM), was developed to investigate the competitive adsorption behavior of lead, copper and cadmium by an indigenous isolate Enterobacter sp. J1 able to tolerate high concentrations of a variety of heavy metals. Using the proposed combinative experimental design, two different experiment designs in a ternary metal biosorption system can be integrated to a succinct experiment and the number of experimental trials was markedly reduced from 38 to 26 by reusing the mutual experimental data. Triangular contour diagrams and triangular three-dimensional surface plots were generated to describe the ternary metal biosorption equilibrium data in mixture design systems. The results show that the preference of metal sorption of Enterobacter sp. J1 decreased in the order of Pb 2+ > Cu 2+ > Cd 2+ . The presence of other metals resulted in a competitive effect. The influence of the other two metals in ternary metal biosorption system can be easily determined by comparing the stray distance from the single metal biosorption. The behavior of competitive biosorption was successfully described and predicted using a combined Langmuir-Freundlich model along with new three-dimensional contour-surface plots

Exploring multi-metal biosorption by indigenous metal-hyperresistant Enterobacter sp. J1 using experimental design methodologies

Energy Technology Data Exchange (ETDEWEB)

Lu, W.-B. [Department of Cosmetic Science, Chung Hwa University of Medical Technology, Tainan, Taiwan (China); Kao, W.-C.; Shi, J.-J. [Department of Chemical Engineering, National Cheng Kung University, Tainan, Taiwan (China); Chang, J.-S. [Department of Chemical Engineering, National Cheng Kung University, Tainan, Taiwan (China)], E-mail: changjs@mail.ncku.edu.tw

2008-05-01

A novel experimental design, combining mixture design and response surface methodology (RSM), was developed to investigate the competitive adsorption behavior of lead, copper and cadmium by an indigenous isolate Enterobacter sp. J1 able to tolerate high concentrations of a variety of heavy metals. Using the proposed combinative experimental design, two different experiment designs in a ternary metal biosorption system can be integrated to a succinct experiment and the number of experimental trials was markedly reduced from 38 to 26 by reusing the mutual experimental data. Triangular contour diagrams and triangular three-dimensional surface plots were generated to describe the ternary metal biosorption equilibrium data in mixture design systems. The results show that the preference of metal sorption of Enterobacter sp. J1 decreased in the order of Pb{sup 2+} > Cu{sup 2+} > Cd{sup 2+}. The presence of other metals resulted in a competitive effect. The influence of the other two metals in ternary metal biosorption system can be easily determined by comparing the stray distance from the single metal biosorption. The behavior of competitive biosorption was successfully described and predicted using a combined Langmuir-Freundlich model along with new three-dimensional contour-surface plots.

Power load limits of the WENDELSTEIN 7-X target elements-comparison of experimental results and design values for power loads up to the critical heat flux

International Nuclear Information System (INIS)

Greuner, H; Boeswirth, B; Boscary, J; Leuprecht, A; Plankensteiner, A

2007-01-01

The power load limits of the WENDELSTEIN7-X divertor target elements were experimentally evaluated with heat loads considerably exceeding the expected operating conditions. The water-cooled elements are designed for steady-state heat flux of 10 MW m -2 and to remove a power load up to 100 kW. The elements must allow a limited operation time at 12 MW m -2 steady-state and should not fail for short pulses of up to 15 MW m -2 for cooling conditions in the subcooled nucleate boiling regime. In the framework of the qualification phase, pre-series target elements were loaded up to 24 MW m -2 without loss of CFC tiles. A critical heat flux at the target of 31 MW m -2 was achieved. The paper discusses the results of the tests performed at the high heat flux test facility GLADIS. The experimental results compared to transient nonlinear fine element method (FEM) calculations confirm a high thermal safety margin of the target design sufficient for plasma operation in W7-X

Optimizing an experimental design for an electromagnetic experiment

Science.gov (United States)

Roux, Estelle; Garcia, Xavier

2013-04-01

Most of geophysical studies focus on data acquisition and analysis, but another aspect which is gaining importance is the discussion on acquisition of suitable datasets. This can be done through the design of an optimal experiment. Optimizing an experimental design implies a compromise between maximizing the information we get about the target and reducing the cost of the experiment, considering a wide range of constraints (logistical, financial, experimental …). We are currently developing a method to design an optimal controlled-source electromagnetic (CSEM) experiment to detect a potential CO2 reservoir and monitor this reservoir during and after CO2 injection. Our statistical algorithm combines the use of linearized inverse theory (to evaluate the quality of one given design via the objective function) and stochastic optimization methods like genetic algorithm (to examine a wide range of possible surveys). The particularity of our method is that it uses a multi-objective genetic algorithm that searches for designs that fit several objective functions simultaneously. One main advantage of this kind of technique to design an experiment is that it does not require the acquisition of any data and can thus be easily conducted before any geophysical survey. Our new experimental design algorithm has been tested with a realistic one-dimensional resistivity model of the Earth in the region of study (northern Spain CO2 sequestration test site). We show that a small number of well distributed observations have the potential to resolve the target. This simple test also points out the importance of a well chosen objective function. Finally, in the context of CO2 sequestration that motivates this study, we might be interested in maximizing the information we get about the reservoir layer. In that case, we show how the combination of two different objective functions considerably improve its resolution.

Shear or bending? Experimental results on large t-shaped prestressed conrete beams

NARCIS (Netherlands)

Ensink, S.W.H.; Van der Veen, C.; De Boer, A.

2015-01-01

Experimental results of four shear tests on two large prestressed concrete beams are compared to nonlinear analysis and design code calculations. The beams have a length of 12 m and a depth of 1.3 m and are reinforced with stirrups and pre-tensioning. The four tests consist of a single point load at

Mechanical design and first experimental results of an upgraded technical PERMCAT reactor for tritium recovery in the fuel cycle of a fusion machine

Energy Technology Data Exchange (ETDEWEB)

Welte, S., E-mail: stefan.welte@kit.edu [Karlsruhe Institute of Technology (KIT), Forschungszentrum Karlsruhe, Institute for Technical Physics, Tritium Laboratory Karlsruhe, Hermann v. Helmholtz Platz 1, 76344 Eggenstein Leopoldshafen (Germany); Demange, D.; Wagner, R. [Karlsruhe Institute of Technology (KIT), Forschungszentrum Karlsruhe, Institute for Technical Physics, Tritium Laboratory Karlsruhe, Hermann v. Helmholtz Platz 1, 76344 Eggenstein Leopoldshafen (Germany)

2010-12-15

The PERMCAT process developed for the final clean-up stage of the Tokamak Exhaust Processing systems of the ITER tritium plant combines a catalytic reactor and a Pd/Ag permeator in a single component. A first generation technical PERMCAT has been successfully operated as part of the CAPER experiment at the Tritium Laboratory Karlsruhe for several years. Various alternative PERMCAT mechanical designs were proposed and studied on small-scale prototypes. An upgraded technical PERMCAT reactor was designed, manufactured and commissioned with deuterium. A parallel arrangement of finger-type membranes inserted in a single catalyst bed design was chosen to simplify the geometry and the manufacturing while improving the robustness of the reactor. The component has been designed and manufactured to be fully tritium compatible and also fully compatible with both process and electrical connections of the previous PERMCAT to be replaced. The new PERMCAT mechanical design is more compact and easy to manufacture. This PERMCAT reactor was submitted to functional tests and experiments based on isotopic exchanges between H{sub 2}O and D{sub 2} to measure the processing performances. The first experimental results show decontamination factors versus flow rates better than all previously measured.

Mechanical design and first experimental results of an upgraded technical PERMCAT reactor for tritium recovery in the fuel cycle of a fusion machine

International Nuclear Information System (INIS)

Welte, S.; Demange, D.; Wagner, R.

2010-01-01

The PERMCAT process developed for the final clean-up stage of the Tokamak Exhaust Processing systems of the ITER tritium plant combines a catalytic reactor and a Pd/Ag permeator in a single component. A first generation technical PERMCAT has been successfully operated as part of the CAPER experiment at the Tritium Laboratory Karlsruhe for several years. Various alternative PERMCAT mechanical designs were proposed and studied on small-scale prototypes. An upgraded technical PERMCAT reactor was designed, manufactured and commissioned with deuterium. A parallel arrangement of finger-type membranes inserted in a single catalyst bed design was chosen to simplify the geometry and the manufacturing while improving the robustness of the reactor. The component has been designed and manufactured to be fully tritium compatible and also fully compatible with both process and electrical connections of the previous PERMCAT to be replaced. The new PERMCAT mechanical design is more compact and easy to manufacture. This PERMCAT reactor was submitted to functional tests and experiments based on isotopic exchanges between H 2 O and D 2 to measure the processing performances. The first experimental results show decontamination factors versus flow rates better than all previously measured.

Comparison of ATHENA/RELAP results against ice experimental data

CERN Document Server

Moore-Richard, L

2002-01-01

In order to demonstrate the adequacy of the International Thermonuclear Experimental Reactor design from a safety stand point as well as investigating the behavior of two-phase flow phenomena during an ingress of coolant event, an integrated ICE test facility was constructed in Japan. The data generated from the ICE facility offers a valuable means to validate computer codes such as ATHENA /RELAP5, which is one of the codes used at the Idaho National Engineering And Environmental Laboratory (INEEL) to evaluate the safety of various fusion reactor concepts. In this paper we compared numerical results generated by the ATHENA code with corresponding test data from the ICE facility. Overall we found good agreement between the test data and the predicted results.

An experimental result of surface roughness machining performance in deep hole drilling

Directory of Open Access Journals (Sweden)

Mohamad Azizah

2016-01-01

Full Text Available This study presents an experimental result of a deep hole drilling process for Steel material at different machining parameters which are feed rate (f, spindle speed (s, the depth of the hole (d and MQL, number of drops (m on surface roughness, Ra. The experiment was designed using two level full factorial design of experiment (DoE with centre points to collect surface roughness, Ra values. The signal to noise (S/N ratio analysis was used to discover the optimum level for each machining parameters in the experiment.

An Underlay Communication Channel for 5G Cognitive Mesh Networks: Packet Design, Implementation, Analysis, and Experimental Results

Energy Technology Data Exchange (ETDEWEB)

Tarek Haddadin; Stephen Andrew Laraway; Arslan Majid; Taylor Sibbett; Daryl Leon Wasden; Brandon F Lo; Lloyd Landon; David Couch; Hussein Moradi; Behrouz Farhang-Boroujeny

2016-04-01

This paper proposes and presents the design and implementation of an underlay communication channel (UCC) for 5G cognitive mesh networks. The UCC builds its waveform based on filter bank multicarrier spread spectrum (FB-MCSS) signaling. The use of this novel spread spectrum signaling allows the device-to-device (D2D) user equipments (UEs) to communicate at a level well below noise temperature and hence, minimize taxation on macro-cell/small-cell base stations and their UEs in 5G wireless systems. Moreover, the use of filter banks allows us to avoid those portions of the spectrum that are in use by macro-cell and small-cell users. Hence, both D2D-to-cellular and cellular-to-D2D interference will be very close to none. We propose a specific packet for UCC and develop algorithms for packet detection, timing acquisition and tracking, as well as channel estimation and equalization. We also present the detail of an implementation of the proposed transceiver on a software radio platform and compare our experimental results with those from a theoretical analysis of our packet detection algorithm.

The IPIRG-1 pipe system fracture tests: Experimental results

International Nuclear Information System (INIS)

Scott, P.; Olson, R.J.; Wilkowski, G.M.

1994-01-01

As part of the First International Piping Integrity Research Group (IPIRG-1) program, six dynamic pipe system experiments were conducted. The objective of these experiments was to generate experimental data to assess analysis methodologies for characterizing the fracture behavior of circumferentially cracked pipe in a representative piping system subjected to combined inertial and displacement-controlled stresses. A unique experimental facility was designed and constructed. The pipe system evaluated was an expansion loop with over 30 m (100 feet) of 16-inch nominal diameter Schedule 100 pipe. The experimental facility was equipped with special hardware to ensure that system boundary conditions could be appropriately modeled. The test matrix involved one uncracked and five cracked dynamic pipe system experiments. The uncracked-pipe experiment was conducted to evaluate the piping system damping and natural frequency characteristics. The cracked-pipe experiments were conducted to evaluate the fracture behavior, piping system response, and fracture stability characteristics of five different materials. All cracked-pipe experiments were conducted at PWR conditions. Material characterization efforts provided the tensile and fracture toughness properties of the different pipe materials at various strain rates and temperatures. Key results from the six pipe system experiments and material characterization efforts are presented. Detailed analyses will be published in a companion paper

Spent Fuel Transportation Package Performance Study - Experimental Design Challenges

International Nuclear Information System (INIS)

Snyder, A. M.; Murphy, A. J.; Sprung, J. L.; Ammerman, D. J.; Lopez, C.

2003-01-01

Numerous studies of spent nuclear fuel transportation accident risks have been performed since the late seventies that considered shipping container design and performance. Based in part on these studies, NRC has concluded that the level of protection provided by spent nuclear fuel transportation package designs under accident conditions is adequate. [1] Furthermore, actual spent nuclear fuel transport experience showcase a safety record that is exceptional and unparalleled when compared to other hazardous materials transportation shipments. There has never been a known or suspected release of the radioactive contents from an NRC-certified spent nuclear fuel cask as a result of a transportation accident. In 1999 the United States Nuclear Regulatory Commission (NRC) initiated a study, the Package Performance Study, to demonstrate the performance of spent fuel and spent fuel packages during severe transportation accidents. NRC is not studying or testing its current regulations, a s the rigorous regulatory accident conditions specified in 10 CFR Part 71 are adequate to ensure safe packaging and use. As part of this study, NRC currently plans on using detailed modeling followed by experimental testing to increase public confidence in the safety of spent nuclear fuel shipments. One of the aspects of this confirmatory research study is the commitment to solicit and consider public comment during the scoping phase and experimental design planning phase of this research

Optimizing Nuclear Reaction Analysis (NRA) using Bayesian Experimental Design

International Nuclear Information System (INIS)

Toussaint, Udo von; Schwarz-Selinger, Thomas; Gori, Silvio

2008-01-01

Nuclear Reaction Analysis with 3 He holds the promise to measure Deuterium depth profiles up to large depths. However, the extraction of the depth profile from the measured data is an ill-posed inversion problem. Here we demonstrate how Bayesian Experimental Design can be used to optimize the number of measurements as well as the measurement energies to maximize the information gain. Comparison of the inversion properties of the optimized design with standard settings reveals huge possible gains. Application of the posterior sampling method allows to optimize the experimental settings interactively during the measurement process.

Experimental study of liquid-metal target designs of accelerating-controlled systems

International Nuclear Information System (INIS)

Iarmonov, Mikhail; Makhov, Kirill; Novozhilova, Olga; Meluzov, A.G.; Beznosov, A.V.

2011-01-01

Models of a liquid-metal target of an accelerator-controlled system have been experimentally studied at the Nizhny Novgorod State Technical University to develop an optimal design of the flow part of the target. The main explored variants of liquid-metal targets are: Design with a diaphragm (firm-and-impervious plug) mounted on the pipe tap of particle transport from the accelerator cavity to the working cavity of the liquid-metal target. Design without a diaphragm on the pipe tab of particle transport from the accelerator. The study was carried out in a high-temperature liquid-metal test bench under the conditions close to full-scale ones: the temperature of the eutectic lead-bismuth alloy was 260degC - 400degC, the coolant mass flow was 5-80 t/h, and the rarefaction in the gas cavity was 10 5 Pa, the coefficient of geometric similarity equal to 1. The experimental studies of hydrodynamic characteristics of flow parts in the designs of targets under full-scale conditions indicated high efficiency of a target in triggering, operating, and deactivating modes. Research and technology instructions for designs of the flow part of the liquid-metal target, the target design as a whole, and the target circuit of accelerator-controlled systems were formulated as a result of the studies. (author)

Design and experimental investigation of a Multi-segment plate concentrated photovoltaic solar energy system

International Nuclear Information System (INIS)

Wang, Gang; Chen, Zeshao; Hu, Peng

2017-01-01

Highlights: • A multi-segment plate concentrated photovoltaic solar energy system was proposed. • A prototype of this new concentrator was developed for experimental investigation. • Experimental investigation results showed a good concentrating uniformity. - Abstract: Solar energy is one of the most promising renewable energies and meaningful for the sustainable development of energy source. A multi-segment plate concentrated photovoltaic (CPV) solar power system was proposed in this paper, the design principle of the multi-segment plate concentrator of this solar power system was given, which could provide uniform solar radiation flux density distribution on solar cells. A prototype of this multi-segment plate CPV solar power system was developed for the experimental study, aiming at the investigations of solar radiation flux density distribution and PV performances under this concentrator design. The experimental results showed that the solar radiation flux density distribution provided by the multi-segment plate concentrator had a good uniformity, and the number and temperature of solar cells both influence the photoelectric transformation efficiency of the CPV solar power system.

Comparison of Experimental Surface and Flow Field Measurements to Computational Results of the Juncture Flow Model

Science.gov (United States)

Roozeboom, Nettie H.; Lee, Henry C.; Simurda, Laura J.; Zilliac, Gregory G.; Pulliam, Thomas H.

2016-01-01

Wing-body juncture flow fields on commercial aircraft configurations are challenging to compute accurately. The NASA Advanced Air Vehicle Program's juncture flow committee is designing an experiment to provide data to improve Computational Fluid Dynamics (CFD) modeling in the juncture flow region. Preliminary design of the model was done using CFD, yet CFD tends to over-predict the separation in the juncture flow region. Risk reduction wind tunnel tests were requisitioned by the committee to obtain a better understanding of the flow characteristics of the designed models. NASA Ames Research Center's Fluid Mechanics Lab performed one of the risk reduction tests. The results of one case, accompanied by CFD simulations, are presented in this paper. Experimental results suggest the wall mounted wind tunnel model produces a thicker boundary layer on the fuselage than the CFD predictions, resulting in a larger wing horseshoe vortex suppressing the side of body separation in the juncture flow region. Compared to experimental results, CFD predicts a thinner boundary layer on the fuselage generates a weaker wing horseshoe vortex resulting in a larger side of body separation.

Conceptual design study of fusion experimental reactor (FY86 FER)

International Nuclear Information System (INIS)

Saito, Ryusei; Kashihara, Shin-ichiro; Itoh, Shin-ichi

1987-08-01

This report describes the results of conceptual design study on plant systems for the Fusion Experimental Reactor (FY86 FER). Design studies for FER plant systems have been continued from FY85, especially for design modifications made in accordance with revisions of plasma scaling parameters and system improvements. This report describes 1) system construction, 2) site and reactor building plan, 3) repaire and maintenance system, 4) tritium circulation system, 5) heating, ventilation and air conditioning system, 6) tritium clean-up system, 7) cooling and baking system, 8) waste treatment and storage system, 9) control system, 10) electric power system, 11) site factory plan, all of which are a part of FY86 design work. The plant systems described in this report generally have been based on the FY86 FER (ACS Reactor) which is an one of the six candidates for FER. (author)

Visualizing Experimental Designs for Balanced ANOVA Models using Lisp-Stat

Directory of Open Access Journals (Sweden)

Philip W. Iversen

2004-12-01

Full Text Available The structure, or Hasse, diagram described by Taylor and Hilton (1981, American Statistician provides a visual display of the relationships between factors for balanced complete experimental designs. Using the Hasse diagram, rules exist for determining the appropriate linear model, ANOVA table, expected means squares, and F-tests in the case of balanced designs. This procedure has been implemented in Lisp-Stat using a software representation of the experimental design. The user can interact with the Hasse diagram to add, change, or delete factors and see the effect on the proposed analysis. The system has potential uses in teaching and consulting.

Experimentation of a LiBr–H2O absorption process for long-term solar thermal storage: Prototype design and first results

International Nuclear Information System (INIS)

N'Tsoukpoe, K.E.; Le Pierrès, N.; Luo, L.

2013-01-01

The long-term thermal storage by absorption process studied in this paper is devoted to building heating. A demonstrative prototype that can store 8 kWh of heat and produce a heating power of 1 kW has been designed and built. It has been tested in static and dynamic operating conditions, which are compatible with domestic solar thermal and heating plants. The process operating principle, the prototype design and first experimental results are presented and discussed in this contribution. The charging process has been proved successful. The observed power during the charging phases is satisfactory, according to the process design for a real plant (2–5 kW). Absorption during discharging phase is also verified. Discharging tests show that absorption operates in conditions that could allow house heating as the absorber outlet solution temperature can reach 40 °C. However, some problems related to the absorber design have not allowed observing the heat recovery by the heat transfer fluid as expected. Some avenues are explored prior to a new and more appropriate design and eventually a new operating mode. Various aspects such as the use of a heat and mass transfer enhancement additive and stratification in the solution storage tank have also been addressed. - Highlights: ► A long-term thermal storage prototype is tested under practical conditions. ► For the prototype design, a separate reactor is used with integrated components. ► The observed powers during the charging phases are satisfactory (2–5 kW). ► Following crystallisation phases, discharging tests enabled the crystal dissolution. ► Absorber temperature that could allow house heating (up to 40°C) has been observed

Flow cytometry: design, development and experimental validation

International Nuclear Information System (INIS)

Seigneur, Alain

1987-01-01

The flow cytometry techniques allow the analysis and sorting of living biologic cells at rates above five to ten thousand events per second. After a short review, we present in this report the design and development of a 'high-tech' apparatus intended for research laboratories and the experimental results. The first part deals with the physical principles allowing morphologic and functional analysis of cells or cellular components. The measured parameters are as follows: electrical resistance pulse sizing, light scattering and fluorescence. Hydrodynamic centering is used, and in the same way, the division of a water-stream into droplets leading to electrostatic sorting of particles. The second part deals with the apparatus designed by the 'Commissariat a l'Energie Atomique' (C.E.A.) and industrialised by 'ODAM' (ATC 3000). The last part of this thesis work is the performance evaluations of this cyto-meter. The difference between the two size measurement methods are analyzed: electrical resistance pulse sizing versus small-angle light scattering. By an original optics design, high sensitivity has been reached in the fluorescence measurement: the equivalent noise corresponds to six hundred fluorescein isothiocyanate (FITC) molecules. The sorting performances have also been analyzed and the cell viability proven. (author) [fr

Summary of the experimental multi-purpose very high temperature gas cooled reactor design

International Nuclear Information System (INIS)

1984-12-01

The report presents the design of Multi-purpose Very High Temperature Gas Cooled Reactor (the Experimental VHTR) based on the second stage of detailed design which was completed on March 1984, in the from of ''An application of reactor construction permit Appendix 8''. The Experimental VHTR is designed to satisfy with the design specification for the reactor thermal output 50 MW and reactor outlet temperature 950 0 C. The adequacy of the design is also checked by the safety analysis. The planning of plant system and safety is summarized such as safety design requirements and conformance with them, seismic design and plant arrangement. Concerning with the system of the Experimental VHTR the design basis, design data and components are described in the order. (author)

Design Issues and Inference in Experimental L2 Research

Science.gov (United States)

Hudson, Thom; Llosa, Lorena

2015-01-01

Explicit attention to research design issues is essential in experimental second language (L2) research. Too often, however, such careful attention is not paid. This article examines some of the issues surrounding experimental L2 research and its relationships to causal inferences. It discusses the place of research questions and hypotheses,…

Use of Experimental Design for Peuhl Cheese Process Optimization ...

African Journals Online (AJOL)

Use of Experimental Design for Peuhl Cheese Process Optimization. ... Journal of Applied Sciences and Environmental Management ... This work consisting in use of a central composite design enables the determination of optimal process conditions concerning: leaf extract volume added (7 mL), heating temperature ...

Experimentally supported control design for a direct drive robot

NARCIS (Netherlands)

Kostic, D.; Jager, de A.G.; Steinbuch, M.

2002-01-01

We promote the idea of an experimentally supported control design as a successful way to achieve accurate tracking of reference robot motions, under disturbance conditions and given the uncertainties arising from modeling errors. The Hinf robust control theory is used for design of motion

Cooperative Experimental System Development - cooperative techniques beyound initial design and analysis

DEFF Research Database (Denmark)

Grønbæk, Kaj; Kyng, Morten; Mogensen, Preben Holst

1995-01-01

This chapter represents a step towards the establishment of a new system development approach, called Cooperative Experimental System Development (CESD). CESD seeks to overcome a number of limitations in existing approaches: specification oriented methods usually assume that system design can....../design activities of development projects. In contrast, the CESD approach is characterized by its focus on: active user involvement throughout the entire development process; prototyping experiments closely coupled to work-situations and use-scenarios; transforming results from early cooperative analysis...... be based solely on observation and detached reflection; prototyping methods often have a narrow focus on the technical construction of various kinds of prototypes; Participatory Design techniques—including the Scandinavian Cooperative Design (CD) approaches—seldom go beyond the early analysis...

Development and Validation of a Rubric for Diagnosing Students’ Experimental Design Knowledge and Difficulties

Science.gov (United States)

Dasgupta, Annwesa P.; Anderson, Trevor R.

2014-01-01

It is essential to teach students about experimental design, as this facilitates their deeper understanding of how most biological knowledge was generated and gives them tools to perform their own investigations. Despite the importance of this area, surprisingly little is known about what students actually learn from designing biological experiments. In this paper, we describe a rubric for experimental design (RED) that can be used to measure knowledge of and diagnose difficulties with experimental design. The development and validation of the RED was informed by a literature review and empirical analysis of undergraduate biology students’ responses to three published assessments. Five areas of difficulty with experimental design were identified: the variable properties of an experimental subject; the manipulated variables; measurement of outcomes; accounting for variability; and the scope of inference appropriate for experimental findings. Our findings revealed that some difficulties, documented some 50 yr ago, still exist among our undergraduate students, while others remain poorly investigated. The RED shows great promise for diagnosing students’ experimental design knowledge in lecture settings, laboratory courses, research internships, and course-based undergraduate research experiences. It also shows potential for guiding the development and selection of assessment and instructional activities that foster experimental design. PMID:26086658

Conceptual design of fusion experimental reactor (FER)

International Nuclear Information System (INIS)

1984-03-01

A conceptual design study (option C) has been carried out for the fusion experimental reactor (FER). In addition to design of the tokamak reactor and associated systems based on the reference design specifications, feasibility of a water-shield reactor concept was examined as a topical study. The design study for the reference tokamak reactor has produced a reactor concept for the FER, along with major R D items for the concept, based on close examinations on thermal design, electromagnetics, neutronics and remote maintenance. Particular efforts have been directed to the area of electromagnetics. Detailed analyses with close simulation models have been performed on PF coil arrangements and configurations, shell effects of the blanket for plasma position unstability, feedback control, and eddy currents during disruptions. The major design specifications are as follows; Peak fusion power 437 MW Major radius 5.5 m Minor radius 1.1 m Plasma elongation 1.5 Plasma current 5.3 MA Toroidal beta 4 % Field on axis 5.7 T (author)

Experimental results of active control on a large structure to suppress vibration

Science.gov (United States)

Dunn, H. J.

1991-01-01

Three design methods, Linear Quadratic Gaussian with Loop Transfer Recovery (LQG/LTR), H-infinity, and mu-synthesis, are used to obtain compensators for suppressing the vibrations of a 10-bay vertical truss structure, a component typical of what may be used to build a large space structure. For the design process the plant dynamic characteristics of the structure were determined experimentally using an identification method. The resulting compensators were implemented on a digital computer and tested for their ability to suppress the first bending mode response of the 10-bay vertical truss. Time histories of the measured motion are presented, and modal damping obtained during the experiments are compared with analytical predictions. The advantages and disadvantages of using the various design methods are discussed.

Conceptual design of Fusion Experimental Reactor (FER)

International Nuclear Information System (INIS)

Tone, T.; Fujisawa, N.

1983-01-01

Conceptual design studies of the Fusion Experimental Reactor (FER) have been performed. The FER has an objective of achieving selfignition and demonstrating engineering feasibility as a next generation tokamak to JT-60. Various concepts of the FER have been considered. The reference design is based on a double-null divertor. Optional design studies with some attractive features based on advanced concepts such as pumped limiter and RF current drive have been carried out. Key design parameters are; fusion power of 440 MW, average neutron wall loading of 1MW/m 2 , major radius of 5.5m, plasma minor radius of 1.1m, plasma elongation of 1.5, plasma current of 5.3MA, toroidal beta of 4%, toroidal field on plasma axis of 5.7T and tritium breeding ratio of above unity

Design, construction and testing of a radon experimental chamber; Diseno, construccion y pruebas de una camara experimental de radon

Energy Technology Data Exchange (ETDEWEB)

Chavez B, A; Balcazar G, M

1991-10-15

To carry out studies on the radon behavior under controlled and stable conditions it was designed and constructed a system that consists of two parts: a container of mineral rich in Uranium and an experimentation chamber with radon united one to the other one by a step valve. The container of uranium mineral approximately contains 800 gr of uranium with a law of 0.28%; the radon gas emanated by the mineral is contained tightly by the container. When the valve opens up the radon gas it spreads to the radon experimental chamber; this contains 3 accesses that allow to install different types of detectors. The versatility of the system is exemplified with two experiments: 1. With the radon experimental chamber and an associated spectroscopic system, the radon and two of its decay products are identified. 2. The design of the system allows to couple the mineral container to other experimental geometries to demonstrate this fact it was coupled and proved a new automatic exchanger system of passive detectors of radon. The results of the new automatic exchanger system when it leave to flow the radon freely among the container and the automatic exchanger through a plastic membrane of 15 m. are shown. (Author)

Surface laser marking optimization using an experimental design approach

Science.gov (United States)

Brihmat-Hamadi, F.; Amara, E. H.; Lavisse, L.; Jouvard, J. M.; Cicala, E.; Kellou, H.

2017-04-01

Laser surface marking is performed on a titanium substrate using a pulsed frequency doubled Nd:YAG laser ( λ= 532 nm, τ pulse=5 ns) to process the substrate surface under normal atmospheric conditions. The aim of the work is to investigate, following experimental and statistical approaches, the correlation between the process parameters and the response variables (output), using a Design of Experiment method (DOE): Taguchi methodology and a response surface methodology (RSM). A design is first created using MINTAB program, and then the laser marking process is performed according to the planned design. The response variables; surface roughness and surface reflectance were measured for each sample, and incorporated into the design matrix. The results are then analyzed and the RSM model is developed and verified for predicting the process output for the given set of process parameters values. The analysis shows that the laser beam scanning speed is the most influential operating factor followed by the laser pumping intensity during marking, while the other factors show complex influences on the objective functions.

COMPARISON OF EXPERIMENTAL-DESIGNS COMBINING PROCESS AND MIXTURE VARIABLES .1. DESIGN CONSTRUCTION AND THEORETICAL EVALUATION

NARCIS (Netherlands)

DUINEVELD, CAA; SMILDE, AK; DOORNBOS, DA

The combination of process variables and mixture variables in experimental design is a problem which has not yet been solved. It is examined here whether a set of designs can be found which can be used for a series of models of reasonable complexity. The proposed designs are compared with known

COMPARISON OF EXPERIMENTAL-DESIGNS COMBINING PROCESS AND MIXTURE VARIABLES .1. DESIGN CONSTRUCTION AND THEORETICAL EVALUATION

NARCIS (Netherlands)

DUINEVELD, C. A. A.; Smilde, A. K.; Doornbos, D. A.

1993-01-01

The combination of process variables and mixture variables in experimental design is a problem which has not yet been solved. It is examined here whether a set of designs can be found which can be used for a series of models of reasonable complexity. The proposed designs are compared with known

An Experimental Verification of morphology of ibuprofen crystals from CAMD designed solvent

DEFF Research Database (Denmark)

Karunanithi, Arunprakash T.; Acquah, Charles; Achenie, Luke E.K.

2007-01-01

of crystals formed from solvents, necessitates additional experimental verification steps. In this work we report the experimental verification of crystal morphology for the case study, solvent design for ibuprofen crystallization, presented in Karunanithi et al. [2006. A computer-aided molecular design...

Experimental Design for Hanford Low-Activity Waste Glasses with High Waste Loading

International Nuclear Information System (INIS)

Piepel, Gregory F.; Cooley, Scott K.; Vienna, John D.; Crum, Jarrod V.

2015-01-01

This report discusses the development of an experimental design for the initial phase of the Hanford low-activity waste (LAW) enhanced glass study. This report is based on a manuscript written for an applied statistics journal. Appendices A, B, and E include additional information relevant to the LAW enhanced glass experimental design that is not included in the journal manuscript. The glass composition experimental region is defined by single-component constraints (SCCs), linear multiple-component constraints (MCCs), and a nonlinear MCC involving 15 LAW glass components. Traditional methods and software for designing constrained mixture experiments with SCCs and linear MCCs are not directly applicable because of the nonlinear MCC. A modification of existing methodology to account for the nonlinear MCC was developed and is described in this report. One of the glass components, SO 3 , has a solubility limit in glass that depends on the composition of the balance of the glass. A goal was to design the experiment so that SO 3 would not exceed its predicted solubility limit for any of the experimental glasses. The SO 3 solubility limit had previously been modeled by a partial quadratic mixture model expressed in the relative proportions of the 14 other components. The partial quadratic mixture model was used to construct a nonlinear MCC in terms of all 15 components. In addition, there were SCCs and linear MCCs. This report describes how a layered design was generated to (i) account for the SCCs, linear MCCs, and nonlinear MCC and (ii) meet the goals of the study. A layered design consists of points on an outer layer, and inner layer, and a center point. There were 18 outer-layer glasses chosen using optimal experimental design software to augment 147 existing glass compositions that were within the LAW glass composition experimental region. Then 13 inner-layer glasses were chosen with the software to augment the existing and outer-layer glasses. The experimental

Conceptual design of fusion experimental reactor (FER)

International Nuclear Information System (INIS)

1984-02-01

This report describes the engineering conceptual design of Fusion Experimental Reactor (FER) which is to be built as a next generation tokamak machine. This design covers overall reactor systems including MHD equilibrium analysis, mechanical configuration of reactor, divertor, pumped limiter, first wall/breeding blanket/shield, toroidal field magnet, poloidal field magnet, cryostat, electromagnetic analysis, vacuum system, power handling and conversion, NBI, RF heating device, tritium system, neutronics, maintenance, cooling system and layout of facilities. The engineering comparison of a divertor with pumped limiters and safety analysis of reactor systems are also conducted. (author)

Fast Bayesian optimal experimental design and its applications

KAUST Repository

Long, Quan

2015-01-01

We summarize our Laplace method and multilevel method of accelerating the computation of the expected information gain in a Bayesian Optimal Experimental Design (OED). Laplace method is a widely-used method to approximate an integration

Conceptual design study of quasi-steady state fusion experimental reactor (FEQ-Q), part 1

International Nuclear Information System (INIS)

1985-12-01

Since 1980 the design study has been conducted at JAERI for the Fusion Experimental Reactor (FER) which has been proposed to be the next machine to JT-60 in the Japanese long term program of fusion reactor development. Starting from 1984 JER design is being reviewed and redesigned. This report is a part of the interim report which describes the results obtained in the review and redesign activities in FY 1984. The results of the following design items are included; core plasma, reactor structure, reactor core components, magnets. (author)

Optimal Experimental Design of Furan Shock Tube Kinetic Experiments

KAUST Repository

Kim, Daesang

2015-01-07

A Bayesian optimal experimental design methodology has been developed and applied to refine the rate coefficients of elementary reactions in Furan combustion. Furans are considered as potential renewable fuels. We focus on the Arrhenius rates of Furan + OH ↔ Furyl-2 + H2O and Furan ↔ OH Furyl-3 + H2O, and rely on the OH consumption rate as experimental observable. A polynomial chaos surrogate is first constructed using an adaptive pseudo-spectral projection algorithm. The PC surrogate is then exploited in conjunction with a fast estimation of the expected information gain in order to determine the optimal design in the space of initial temperatures and OH concentrations.

Design and experimental results of a new electron gun using a magnetic multipole plasma generator

International Nuclear Information System (INIS)

Tanaka, S.; Yokoyama, K.; Akiba, M.; Araki, M.; Dairaku, M.; Inoue, T.; Mizuno, M.; Okumura, Y.; Ohara, Y.; Seki, M.; Watanabe, K.

1991-01-01

A new electron gun utilizing a magnetic multipole plasma generator was designed and fabricated as the heat source of the high heat flux test facility, called JEBIS (JAERI electron beam irradiation stand). By changing the acceleration grids, this electron gun is able to produce a pencil to a sheetlike electron beams up to 4 A at 100 keV for 1 ms to continuous mode. In this electron gun, magnetic lens system is not adopted to focus the electron beam, but the space charge neutralization effect by the beam plasma produced downstream of the electron gun is utilized to prevent the blow-up of the electron beam. In addition, high permeability metal is embedded in the first and the second grids to magnetically shield the earth field and the stray field from the beam bending magnet. It was experimentally demonstrated that wide range of heat flux from 0.2 MW/m 2 to over 2000 MW/m 2 can be realized at the test sample position about 1.7 m downstream of the electron gun

F(α) curves: Experimental results

International Nuclear Information System (INIS)

Glazier, J.A.; Gunaratne, G.; Libchaber, A.

1988-01-01

We study the transition to chaos at the golden and silver means for forced Rayleigh-Benard (RB) convection in mercury. We present f(α) curves below, at, and above the transition, and provide comparisons to the curves calculated for the one-dimensional circle map. We find good agreement at both the golden and silver means. This confirms our earlier observation that for low amplitude forcing, forced RB convection is well described by the one-dimensional circle map and indicates that the f(α) curve is a good measure of the approach to criticality. For selected subcritical experimental data sets we calculate the degree of subcriticality. We also present both experimental and calculated results for f(α) in the presence of a third frequency. Again we obtain agreement: The presence of random noise or a third frequency narrows the right-hand (negative q) side of the f(α) curve. Subcriticality results in symmetrically narrowed curves. We can also distinguish these cases by examining the power spectra and Poincare sections of the time series

Design and experimental results of feedback control of Ohmic-heating transformer magnetic flux by LHCD power in HT-7 Tokamak

International Nuclear Information System (INIS)

Yiyun Huang

2006-01-01

In order to make a research on long pulse or even steady state operation with non-inductive drive in plasma discharge, a new feedback control scheme instead of the previous one has been designed and operated in HT-7 [HT-7 team presented by J. Li, et al., Plasma Phys. Control. Fusion 42 (2) (2000) 135-146] Tokamak experiment, 2004. Consumption of iron-core transformer magnetic flux (MFT) is feedback controlled for the first time by power of lower hybrid current drive (LHCD) P LH , when the Ohmic-heating circuit current can maintain the plasma current I P constant with another feedback control loop, which make MFT evolve at alternating-change state to avoid flux saturation. Plasma current I P can be maintained steadily up to 120s in this operation mode at reduced plasma parameters (I P ∼50-100KA, average density n-bar e =0.4-0.5x10 19 m -3 , P LH =100-200KW). Design and experimental results are presented in the paper, which including control model analysis, configurations of control system and MFT feedback control experiments in HT-7. The high voltage power supply (HVPS) of LHCD is the main controller that regulates the LHCD power into the plasma to control the MFT

Results from evaporation tests to support the MWTF heat removal system design

International Nuclear Information System (INIS)

Crea, B.A.

1994-01-01

An experimental tests program was conducted to measure the evaporative heat removal from the surface of a tank of simulated waste. The results contained in this report constitute definition design data for the latest heat removal function of the MWTF primary ventilation system

Low pollution combustor designs for CTOL engines - Results of the Experimental Clean Combustor Program

Science.gov (United States)

Roberts, R.; Peduzzi, A.; Niedzwiecki, R. W.

1976-01-01

The NASA/Pratt & Whitney Aircraft Experimental Clean Combustor Program is a multi-year, major contract effort. Primary program objectives are the generation of combustor technology for development of advanced commercial CTOL engines with lower exhaust emissions than current aircraft and demonstration of this technology in a full-scale JT9D engine in 1976. This paper describes the pollution and performance goals, Phase I and II test results, and the Phase III combustor hardware, pollution sampling techniques, and test plans. Best results were obtained with the Vorbix concept which employs multiple burning zones and improved fuel preparation and distribution. Substantial reductions were achieved in all pollutant categories, meeting the 1979 EPA standards for NOx, THC, and smoke when extrapolated to JT9D cycle conditions. The Vorbix concept additionally demonstrated the capability for acceptable altitude relight and did not appear to have unsolvable durability or exit temperature distribution problems.

Plant Disease Severity Assessment-How Rater Bias, Assessment Method, and Experimental Design Affect Hypothesis Testing and Resource Use Efficiency.

Science.gov (United States)

Chiang, Kuo-Szu; Bock, Clive H; Lee, I-Hsuan; El Jarroudi, Moussa; Delfosse, Philippe

2016-12-01

The effect of rater bias and assessment method on hypothesis testing was studied for representative experimental designs for plant disease assessment using balanced and unbalanced data sets. Data sets with the same number of replicate estimates for each of two treatments are termed "balanced" and those with unequal numbers of replicate estimates are termed "unbalanced". The three assessment methods considered were nearest percent estimates (NPEs), an amended 10% incremental scale, and the Horsfall-Barratt (H-B) scale. Estimates of severity of Septoria leaf blotch on leaves of winter wheat were used to develop distributions for a simulation model. The experimental designs are presented here in the context of simulation experiments which consider the optimal design for the number of specimens (individual units sampled) and the number of replicate estimates per specimen for a fixed total number of observations (total sample size for the treatments being compared). The criterion used to gauge each method was the power of the hypothesis test. As expected, at a given fixed number of observations, the balanced experimental designs invariably resulted in a higher power compared with the unbalanced designs at different disease severity means, mean differences, and variances. Based on these results, with unbiased estimates using NPE, the recommended number of replicate estimates taken per specimen is 2 (from a sample of specimens of at least 30), because this conserves resources. Furthermore, for biased estimates, an apparent difference in the power of the hypothesis test was observed between assessment methods and between experimental designs. Results indicated that, regardless of experimental design or rater bias, an amended 10% incremental scale has slightly less power compared with NPEs, and that the H-B scale is more likely than the others to cause a type II error. These results suggest that choice of assessment method, optimizing sample number and number of replicate

Plasma exhaust purification by thermal swing adsorption: Experimental results and modeling

International Nuclear Information System (INIS)

Ricapito, I.; Malara, R.C.

1996-01-01

For several years at the Joint Research Centre-Ispra laboratories, cyclic adsorption processes have been developed for the purification of the plasma exhaust stream of a deuterium-tritium fusion reactor. A purification process consisting of two coupled thermal swing adsorption systems seemed to be the most convenient process. In this context, a screening study was carried out to select the most suitable adsorbent materials and appropriate working temperatures. This was mainly done by experimental measurements of adsorption isotherms of the single components of the plasma exhaust stream and by a careful evaluation of the multicomponent adsorption equilibria. Experiments on adsorption dynamics were carried out in a pilot plant to demonstrate the feasibility and to evaluate the performance of the process. The experimental apparatus was designed to treat gas mixture flow rates up to 20 to 30 standard temperature and pressure l/h. A mathematical model was developed and tested against the experimental results to describe the adsorption process and, in particular, to evaluate and to optimize the process cycle time. 27 refs., 4 figs., 9 tabs

Intuitive web-based experimental design for high-throughput biomedical data.

Science.gov (United States)

Friedrich, Andreas; Kenar, Erhan; Kohlbacher, Oliver; Nahnsen, Sven

2015-01-01

Big data bioinformatics aims at drawing biological conclusions from huge and complex biological datasets. Added value from the analysis of big data, however, is only possible if the data is accompanied by accurate metadata annotation. Particularly in high-throughput experiments intelligent approaches are needed to keep track of the experimental design, including the conditions that are studied as well as information that might be interesting for failure analysis or further experiments in the future. In addition to the management of this information, means for an integrated design and interfaces for structured data annotation are urgently needed by researchers. Here, we propose a factor-based experimental design approach that enables scientists to easily create large-scale experiments with the help of a web-based system. We present a novel implementation of a web-based interface allowing the collection of arbitrary metadata. To exchange and edit information we provide a spreadsheet-based, humanly readable format. Subsequently, sample sheets with identifiers and metainformation for data generation facilities can be created. Data files created after measurement of the samples can be uploaded to a datastore, where they are automatically linked to the previously created experimental design model.

EXPERIMENTAL RESEARCH REGARDING LEATHER APPLICATIONS IN PRODUCT DESIGN

Directory of Open Access Journals (Sweden)

PRALEA Jeni

2015-05-01

Full Text Available This paper presents the role and importance of experimental research in design activity. The designer, as a researcher and a project manager, proposes to establish a relationship between functional-aesthetic-constructive-technological-economic,based on the aesthetic possibilities of the materials used for the experiments. With the aim to identify areas for the application of leather waste resulted from the production process, the paper presents experiments conducted with this material in combination with wood, by using different techniques that lead to different aesthetic effects. Identifying the areas to use and creating products from leather and/or wood waste, is based on the properties of these materials. Leather, the subject of these experiments, has the advantage that it can be used on both sides. Tactile differences of the two sides of this material has both aesthetical and functional advantages, which makes it suitable for applications on products that meet the requirements of "design for all". With differentiated tactile characteristics, in combination with other materials, for these experiments wood, easily "read touch" products can be generated to help people with certain disabilities. Thus, experiments presented in this paper allows the establishment of aesthetic schemes applicable to products that are friendly both with the environment (based on the reuse of wood and leather waste and with the users (can be used as applications, accessories and concepts of products for people with certain disabilities. The designer’s choices or decisions can be based on the results of this experiment. The experiment enables the designer to develop creative, innovative and environmentally friendly products.

Design study of toroidal magnets for tokamak experimental power reactors

International Nuclear Information System (INIS)

Stekly, Z.J.J.; Lucas, E.J.

1976-12-01

This report contains the results of a six-month study of superconducting toroidal field coils for a Tokamak Experimental Power Reactor to be built in the late 1980s. The designs are for 8 T and 12 T maximum magnetic field at the superconducting winding. At each field level two main concepts were generated; one in which each of the 16 coils comprising the system has an individual vacuum vessel and the other in which all the coils are contained in a single vacuum vessel. The coils have a D shape and have openings of 11.25 m x 7.5 m for the 8 T coils and 10.2 m x 6.8 m for the 12 T coils. All the designs utilize rectangular cabled conductor made from copper stabilized Niobium Titanium composite which operates at 4.2 K for the 8 T design and at 2.5 K for the 12 T design. Manufacturing procedures, processes and schedule estimates are also discussed

Design and experimental study of a multi-modal piezoelectric energy harvester

Energy Technology Data Exchange (ETDEWEB)

Xiong, Xing Yu [School of Energy, Power and Mechanical Engineering, North China Electric Power University, Beijing (China); Oyadiji, S. Olutunde [School of Mechanical, Aerospace and Civil Engineering, The University of Manchester, Manchester (United States)

2017-01-15

A multi-modal piezoelectric vibration energy harvester is designed in this article. It consists of a cantilevered base beam and some upper and lower layer beams with rigid masses bonded between the beams as spacers. For a four-layer harvester subjected to random base excitations, relocating the mass positions leads to the generation of up to four close resonance frequencies over the frequency range from 10 Hz to 100 Hz with relative large power output. The harvesters are connected with a resistance decade box and the frequency response functions of the voltage and power on resistive loads are determined. The experimental results are validated with the simulation results using the finite element method. On a certain level of power output, the experimental results show that the multi-modal harvesters can generate a frequency band that is more than two times greater than the frequency band produced by a cantilevered beam harvester.

Design study of the experimental multi-purpose high temperature gas-cooled reactor

International Nuclear Information System (INIS)

Tsunoda, Ryokichi

1981-01-01

In this paper, the design study carried out since 1973 is outlined. The basic conceptual design was performed in fiscal 1973. In this design, concept was established on the total system of the experimental high temperature gas-cooled reactor including heat-utilizing system. The first conceptual design was carried out in fiscal 1974. The range of design was limited to the experimental reactor and its direct heat-removing system. The part 2 of the first conceptual design was performed in fiscal 1975, and the system design concerning the plant characteristics was made. The part 1 of the adjustment design was carried out in fiscal 1976, and the subject was the adjustment design of plant systems. The part 2 was performed in fiscal 1977, and the characteristics of plant control system were analyzed. In fiscal 1978, the analysis of flow characteristics in the core was made. The integrated system design was carried out in fiscal 1979, and the design of the total plant system except heat-utilizing system was started again. The part 1 of the detailed design was performed in fiscal 1980, and in addition, the possibility of increasing power output was examined. The construction cost of the experimental reactor plant estimated in 1979 was far higher than that in 1973. (Kako, I.)

Optimal Experimental Design for Large-Scale Bayesian Inverse Problems

KAUST Repository

Ghattas, Omar

2014-01-06

We develop a Bayesian framework for the optimal experimental design of the shock tube experiments which are being carried out at the KAUST Clean Combustion Research Center. The unknown parameters are the pre-exponential parameters and the activation energies in the reaction rate expressions. The control parameters are the initial mixture composition and the temperature. The approach is based on first building a polynomial based surrogate model for the observables relevant to the shock tube experiments. Based on these surrogates, a novel MAP based approach is used to estimate the expected information gain in the proposed experiments, and to select the best experimental set-ups yielding the optimal expected information gains. The validity of the approach is tested using synthetic data generated by sampling the PC surrogate. We finally outline a methodology for validation using actual laboratory experiments, and extending experimental design methodology to the cases where the control parameters are noisy.

Synthesizing large-scale pyroclastic flows: Experimental design, scaling, and first results from PELE

Science.gov (United States)

Lube, G.; Breard, E. C. P.; Cronin, S. J.; Jones, J.

2015-03-01

Pyroclastic flow eruption large-scale experiment (PELE) is a large-scale facility for experimental studies of pyroclastic density currents (PDCs). It is used to generate high-energy currents involving 500-6500 m3 natural volcanic material and air that achieve velocities of 7-30 m s-1, flow thicknesses of 2-4.5 m, and runouts of >35 m. The experimental PDCs are synthesized by a controlled "eruption column collapse" of ash-lapilli suspensions onto an instrumented channel. The first set of experiments are documented here and used to elucidate the main flow regimes that influence PDC dynamic structure. Four phases are identified: (1) mixture acceleration during eruption column collapse, (2) column-slope impact, (3) PDC generation, and (4) ash cloud diffusion. The currents produced are fully turbulent flows and scale well to natural PDCs including small to large scales of turbulent transport. PELE is capable of generating short, pulsed, and sustained currents over periods of several tens of seconds, and dilute surge-like PDCs through to highly concentrated pyroclastic flow-like currents. The surge-like variants develop a basal <0.05 m thick regime of saltating/rolling particles and shifting sand waves, capped by a 2.5-4.5 m thick, turbulent suspension that grades upward to lower particle concentrations. Resulting deposits include stratified dunes, wavy and planar laminated beds, and thin ash cloud fall layers. Concentrated currents segregate into a dense basal underflow of <0.6 m thickness that remains aerated. This is capped by an upper ash cloud surge (1.5-3 m thick) with 100 to 10-4 vol % particles. Their deposits include stratified, massive, normally and reversely graded beds, lobate fronts, and laterally extensive veneer facies beyond channel margins.

Conceptual design study of fusion experimental reactor (FY86 FER)

International Nuclear Information System (INIS)

Kobayashi, Takeshi; Yamada, Masao; Mizoguchi, Tadanori

1987-09-01

This report describes the results of the reactor configuration/structure design for the fusion experimental reactor (FER) performed in FY 1986. The design was intended to meet the physical and engineering mission of the next step device which was decided by the subcommittee on the next step device of the nuclear fusion council. The objectives of the design study in FY 1986 are to advance and optimize the design concept of the last year because the recommendation of the subcommittee was basically the same as the design philosophy of the last year. Six candidate reactor configurations which correspond to options C ∼ D presented by the subcommittee were extensively examined. Consequently, ACS reactor (Advanced Option-C with Single Null Divertor) was selected as the reference configuration from viewpoints of technical risks and cost performance. Regarding the reactor structure, the following items were investigated intensively: minimization of reactor size, protection of first wall against plasma disruption, simplification of shield structure, reactor configuration which enables optimum arrangement of poloidal field coils. (author)

Experimental results obtained at GANIL

International Nuclear Information System (INIS)

Borrel, V.

1993-01-01

A review of experimental results obtained at GANIL on the study of nuclear structure and nuclear reactions with secondary radioactive beams is presented. Mass measurements by means of the GANIL cyclotrons are described. The possibilities of GANIL/LISE3 for the production and separation of radioactive beams are illustrated through a large variety of experiments. (author). 19 refs., 8 figs

Study of Formulation Variables Influencing Polymeric Microparticles by Experimental Design

Directory of Open Access Journals (Sweden)

Jitendra B. Naik

2014-04-01

Full Text Available The objective of this study was to prepare diclofenac sodium loaded microparticles by single emulsion [oil-in-water (o/w] solvent evaporation method. The 22 experimental design methodology was used to evaluate the effect of two formulation variables on microspheres properties using the Design-Expert® software and evaluated for their particle size, morphology, and encapsulation efficiency and in vitro drug release. The graphical and mathematical analysis of the design showed that the independent variables were a significant effect on the encapsulation efficiency and drug release of microparticles. The low magnitudes of error and significant values of R2 prove the high prognostic ability of the design. The microspheres showed high encapsulation efficiency with an increase in the amount of polymer and decrease in the amount of PVA in the formulation. The particles were found to be spherical with smooth surface. Prolonged drug release and enhancement of encapsulation efficiency of polymeric microparticles can be successfully obtained with an application of experimental design technique.

Experimental Design for Hanford Low-Activity Waste Glasses with High Waste Loading

Energy Technology Data Exchange (ETDEWEB)

Piepel, Gregory F. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Cooley, Scott K. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Vienna, John D. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Crum, Jarrod V. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2015-07-24

This report discusses the development of an experimental design for the initial phase of the Hanford low-activity waste (LAW) enhanced glass study. This report is based on a manuscript written for an applied statistics journal. Appendices A, B, and E include additional information relevant to the LAW enhanced glass experimental design that is not included in the journal manuscript. The glass composition experimental region is defined by single-component constraints (SCCs), linear multiple-component constraints (MCCs), and a nonlinear MCC involving 15 LAW glass components. Traditional methods and software for designing constrained mixture experiments with SCCs and linear MCCs are not directly applicable because of the nonlinear MCC. A modification of existing methodology to account for the nonlinear MCC was developed and is described in this report. One of the glass components, SO₃, has a solubility limit in glass that depends on the composition of the balance of the glass. A goal was to design the experiment so that SO₃ would not exceed its predicted solubility limit for any of the experimental glasses. The SO₃ solubility limit had previously been modeled by a partial quadratic mixture model expressed in the relative proportions of the 14 other components. The partial quadratic mixture model was used to construct a nonlinear MCC in terms of all 15 components. In addition, there were SCCs and linear MCCs. This report describes how a layered design was generated to (i) account for the SCCs, linear MCCs, and nonlinear MCC and (ii) meet the goals of the study. A layered design consists of points on an outer layer, and inner layer, and a center point. There were 18 outer-layer glasses chosen using optimal experimental design software to augment 147 existing glass compositions that were within the LAW glass composition experimental region. Then 13 inner-layer glasses were chosen with the software to augment the existing and outer

Integrated design of Nb-based superalloys: Ab initio calculations, computational thermodynamics and kinetics, and experimental results

International Nuclear Information System (INIS)

Ghosh, G.; Olson, G.B.

2007-01-01

An optimal integration of modern computational tools and efficient experimentation is presented for the accelerated design of Nb-based superalloys. Integrated within a systems engineering framework, we have used ab initio methods along with alloy theory tools to predict phase stability of solid solutions and intermetallics to accelerate assessment of thermodynamic and kinetic databases enabling comprehensive predictive design of multicomponent multiphase microstructures as dynamic systems. Such an approach is also applicable for the accelerated design and development of other high performance materials. Based on established principles underlying Ni-based superalloys, the central microstructural concept is a precipitation strengthened system in which coherent cubic aluminide phase(s) provide both creep strengthening and a source of Al for Al 2 O 3 passivation enabled by a Nb-based alloy matrix with required ductile-to-brittle transition temperature, atomic transport kinetics and oxygen solubility behaviors. Ultrasoft and PAW pseudopotentials, as implemented in VASP, are used to calculate total energy, density of states and bonding charge densities of aluminides with B2 and L2 1 structures relevant to this research. Characterization of prototype alloys by transmission and analytical electron microscopy demonstrates the precipitation of B2 or L2 1 aluminide in a (Nb) matrix. Employing Thermo-Calc and DICTRA software systems, thermodynamic and kinetic databases are developed for substitutional alloying elements and interstitial oxygen to enhance the diffusivity ratio of Al to O for promotion of Al 2 O 3 passivation. However, the oxidation study of a Nb-Hf-Al alloy, with enhanced solubility of Al in (Nb) than in binary Nb-Al alloys, at 1300 deg. C shows the presence of a mixed oxide layer of NbAlO 4 and HfO 2 exhibiting parabolic growth

Statistical experimental design for saltstone mixtures

International Nuclear Information System (INIS)

Harris, S.P.; Postles, R.L.

1992-01-01

The authors used a mixture experimental design for determining a window of operability for a process at the U.S. Department of Energy, Savannah River Site, Defense Waste Processing Facility (DWPF). The high-level radioactive waste at the Savannah River Site is stored in large underground carbon steel tanks. The waste consists of a supernate layer and a sludge layer. Cesium-137 will be removed from the supernate by precipitation and filtration. After further processing, the supernate layer will be fixed as a grout for disposal in concrete vaults. The remaining precipitate will be processed at the DWPF with treated waste tank sludge and glass-making chemicals into borosilicate glass. The leach-rate properties of the supernate grout formed from various mixes of solidified coefficients for NO 3 and chromium were used as a measure of leach rate. Various mixes of cement, Ca(OH) 2 , salt, slag, and fly ash were used. These constituents comprise the whole mix. Thus, a mixture experimental design was used. The regression procedure (PROC REG) in SAS was used to produce analysis of variance (ANOVA) statistics. In addition, detailed model diagnostics are readily available for identifying suspicious observations. For convenience, trillinear contour (TLC) plots, a standard graphics tool for examining mixture response surfaces, of the fitted model were produced using ECHIP

MUP, CEC-DES, STRADE. Codes for uncertainty propagation, experimental design and stratified random sampling techniques

International Nuclear Information System (INIS)

Amendola, A.; Astolfi, M.; Lisanti, B.

1983-01-01

The report describes the how-to-use of the codes: MUP (Monte Carlo Uncertainty Propagation) for uncertainty analysis by Monte Carlo simulation, including correlation analysis, extreme value identification and study of selected ranges of the variable space; CEC-DES (Central Composite Design) for building experimental matrices according to the requirements of Central Composite and Factorial Experimental Designs; and, STRADE (Stratified Random Design) for experimental designs based on the Latin Hypercube Sampling Techniques. Application fields, of the codes are probabilistic risk assessment, experimental design, sensitivity analysis and system identification problems

Conceptual design study of quasi-steady state fusion experimental reactor (FER-Q), part 2

International Nuclear Information System (INIS)

1985-12-01

Since 1980 the design study has been conducted at JAERI for the Fusion Experimental Reactor (FER) which has been proposed to be the next machine to JT-60 in the Japanese long term program of fusion reactor development. Starting from 1984 FER design is being reviewed and redesigned. This report is a part of the interim report which describes the results obtained in the review and redesign activities in FY 1984. The results of the following design items are included: heating/current drive system, plasma position control, power supply, diagnostics, neutronics, blanket test module, repair and maintenance and safety. (author)

New experimental results on strangeness production

International Nuclear Information System (INIS)

Sapozhnikov, M.G.

1998-01-01

New experimental results on the production of φ and f 2 ' (1525) mesons in the annihilation of stopped antiprotons are discussed. The explanation of these facts in the framework of the polarized strangeness model is considered

Methods for the neutronic design of a Supersara experimental loop

International Nuclear Information System (INIS)

Casali, F.; Cepraga, D.

1982-01-01

This paper describes a method for the neutronic design of experimental loops irradiated in D 2 O experimental reactors, like Essor. The calculation approach concerns the definition of a Weigner-Seitz cell where the loop under examination be subjected to the same neutronic conditions as in the actual reactor

Sparse linear models: Variational approximate inference and Bayesian experimental design

International Nuclear Information System (INIS)

Seeger, Matthias W

2009-01-01

A wide range of problems such as signal reconstruction, denoising, source separation, feature selection, and graphical model search are addressed today by posterior maximization for linear models with sparsity-favouring prior distributions. The Bayesian posterior contains useful information far beyond its mode, which can be used to drive methods for sampling optimization (active learning), feature relevance ranking, or hyperparameter estimation, if only this representation of uncertainty can be approximated in a tractable manner. In this paper, we review recent results for variational sparse inference, and show that they share underlying computational primitives. We discuss how sampling optimization can be implemented as sequential Bayesian experimental design. While there has been tremendous recent activity to develop sparse estimation, little attendance has been given to sparse approximate inference. In this paper, we argue that many problems in practice, such as compressive sensing for real-world image reconstruction, are served much better by proper uncertainty approximations than by ever more aggressive sparse estimation algorithms. Moreover, since some variational inference methods have been given strong convex optimization characterizations recently, theoretical analysis may become possible, promising new insights into nonlinear experimental design.

Sparse linear models: Variational approximate inference and Bayesian experimental design

Energy Technology Data Exchange (ETDEWEB)

Seeger, Matthias W [Saarland University and Max Planck Institute for Informatics, Campus E1.4, 66123 Saarbruecken (Germany)

2009-12-01

A wide range of problems such as signal reconstruction, denoising, source separation, feature selection, and graphical model search are addressed today by posterior maximization for linear models with sparsity-favouring prior distributions. The Bayesian posterior contains useful information far beyond its mode, which can be used to drive methods for sampling optimization (active learning), feature relevance ranking, or hyperparameter estimation, if only this representation of uncertainty can be approximated in a tractable manner. In this paper, we review recent results for variational sparse inference, and show that they share underlying computational primitives. We discuss how sampling optimization can be implemented as sequential Bayesian experimental design. While there has been tremendous recent activity to develop sparse estimation, little attendance has been given to sparse approximate inference. In this paper, we argue that many problems in practice, such as compressive sensing for real-world image reconstruction, are served much better by proper uncertainty approximations than by ever more aggressive sparse estimation algorithms. Moreover, since some variational inference methods have been given strong convex optimization characterizations recently, theoretical analysis may become possible, promising new insights into nonlinear experimental design.

Development and Validation of a Rubric for Diagnosing Students' Experimental Design Knowledge and Difficulties.

Science.gov (United States)

Dasgupta, Annwesa P; Anderson, Trevor R; Pelaez, Nancy

2014-01-01

It is essential to teach students about experimental design, as this facilitates their deeper understanding of how most biological knowledge was generated and gives them tools to perform their own investigations. Despite the importance of this area, surprisingly little is known about what students actually learn from designing biological experiments. In this paper, we describe a rubric for experimental design (RED) that can be used to measure knowledge of and diagnose difficulties with experimental design. The development and validation of the RED was informed by a literature review and empirical analysis of undergraduate biology students' responses to three published assessments. Five areas of difficulty with experimental design were identified: the variable properties of an experimental subject; the manipulated variables; measurement of outcomes; accounting for variability; and the scope of inference appropriate for experimental findings. Our findings revealed that some difficulties, documented some 50 yr ago, still exist among our undergraduate students, while others remain poorly investigated. The RED shows great promise for diagnosing students' experimental design knowledge in lecture settings, laboratory courses, research internships, and course-based undergraduate research experiences. It also shows potential for guiding the development and selection of assessment and instructional activities that foster experimental design. © 2014 A. P. Dasgupta et al. CBE—Life Sciences Education © 2014 The American Society for Cell Biology. This article is distributed by The American Society for Cell Biology under license from the author(s). It is available to the public under an Attribution–Noncommercial–Share Alike 3.0 Unported Creative Commons License (http://creativecommons.org/licenses/by-nc-sa/3.0).

Experimental design technique applied to the validation of an instrumental Neutron Activation Analysis procedure

International Nuclear Information System (INIS)

Santos, Uanda Paula de M. dos; Moreira, Edson Gonçalves

2017-01-01

In this study optimization of procedures and standardization of Instrumental Neutron Activation Analysis (INAA) method were carried out for the determination of the elements bromine, chlorine, magnesium, manganese, potassium, sodium and vanadium in biological matrix materials using short irradiations at a pneumatic system. 2 k experimental designs were applied for evaluation of the individual contribution of selected variables of the analytical procedure in the final mass fraction result. The chosen experimental designs were the 2 3 and the 2 4 , depending on the radionuclide half life. Different certified reference materials and multi-element comparators were analyzed considering the following variables: sample decay time, irradiation time, counting time and sample distance to detector. Comparator concentration, sample mass and irradiation time were maintained constant in this procedure. By means of the statistical analysis and theoretical and experimental considerations, it was determined the optimized experimental conditions for the analytical methods that will be adopted for the validation procedure of INAA methods in the Neutron Activation Analysis Laboratory (LAN) of the Research Reactor Center (CRPq) at the Nuclear and Energy Research Institute (IPEN /CNEN-SP). Optimized conditions were estimated based on the results of z-score tests, main effect, interaction effects and better irradiation conditions. (author)

Experimental design technique applied to the validation of an instrumental Neutron Activation Analysis procedure

Energy Technology Data Exchange (ETDEWEB)

Santos, Uanda Paula de M. dos; Moreira, Edson Gonçalves, E-mail: uandapaula@gmail.com, E-mail: emoreira@ipen.br [Instituto de Pesquisas Energéticas e Nucleares (IPEN/CNEN-SP), São Paulo, SP (Brazil)

2017-07-01

In this study optimization of procedures and standardization of Instrumental Neutron Activation Analysis (INAA) method were carried out for the determination of the elements bromine, chlorine, magnesium, manganese, potassium, sodium and vanadium in biological matrix materials using short irradiations at a pneumatic system. 2{sup k} experimental designs were applied for evaluation of the individual contribution of selected variables of the analytical procedure in the final mass fraction result. The chosen experimental designs were the 2{sup 3} and the 2{sup 4}, depending on the radionuclide half life. Different certified reference materials and multi-element comparators were analyzed considering the following variables: sample decay time, irradiation time, counting time and sample distance to detector. Comparator concentration, sample mass and irradiation time were maintained constant in this procedure. By means of the statistical analysis and theoretical and experimental considerations, it was determined the optimized experimental conditions for the analytical methods that will be adopted for the validation procedure of INAA methods in the Neutron Activation Analysis Laboratory (LAN) of the Research Reactor Center (CRPq) at the Nuclear and Energy Research Institute (IPEN /CNEN-SP). Optimized conditions were estimated based on the results of z-score tests, main effect, interaction effects and better irradiation conditions. (author)

Conceptual design of fusion experimental reactor (FER)

International Nuclear Information System (INIS)

1984-01-01

Conceptual Design of Fusion Experimental Reactor (FER) of which the objective will be to realize self-ignition with D-T reaction is reported. Mechanical Configurations of FER are characterized with a noncircular plasma and a double-null divertor. The primary aim of design studies is to demonstrate fissibility of reactor structures as compact and simple as possible with removable torus sectors. The structures of each component such as a first-wall, blanket, shielding, divertor, magnet and so on have been designed. It is also discussed about essential reactor plant system requirements. In addition to the above, a brief concept of a steady-state reactor based on RF current drive is also discussed. The main aim, in this time, is to examine physical studies of a possible RF steady-state reactor. (author)

Bayesian Optimal Experimental Design Using Multilevel Monte Carlo

KAUST Repository

Ben Issaid, Chaouki; Long, Quan; Scavino, Marco; Tempone, Raul

2015-01-01

Experimental design is very important since experiments are often resource-exhaustive and time-consuming. We carry out experimental design in the Bayesian framework. To measure the amount of information, which can be extracted from the data in an experiment, we use the expected information gain as the utility function, which specifically is the expected logarithmic ratio between the posterior and prior distributions. Optimizing this utility function enables us to design experiments that yield the most informative data for our purpose. One of the major difficulties in evaluating the expected information gain is that the integral is nested and can be high dimensional. We propose using Multilevel Monte Carlo techniques to accelerate the computation of the nested high dimensional integral. The advantages are twofold. First, the Multilevel Monte Carlo can significantly reduce the cost of the nested integral for a given tolerance, by using an optimal sample distribution among different sample averages of the inner integrals. Second, the Multilevel Monte Carlo method imposes less assumptions, such as the concentration of measures, required by Laplace method. We test our Multilevel Monte Carlo technique using a numerical example on the design of sensor deployment for a Darcy flow problem governed by one dimensional Laplace equation. We also compare the performance of the Multilevel Monte Carlo, Laplace approximation and direct double loop Monte Carlo.

Bayesian Optimal Experimental Design Using Multilevel Monte Carlo

KAUST Repository

Ben Issaid, Chaouki

2015-01-07

Experimental design is very important since experiments are often resource-exhaustive and time-consuming. We carry out experimental design in the Bayesian framework. To measure the amount of information, which can be extracted from the data in an experiment, we use the expected information gain as the utility function, which specifically is the expected logarithmic ratio between the posterior and prior distributions. Optimizing this utility function enables us to design experiments that yield the most informative data for our purpose. One of the major difficulties in evaluating the expected information gain is that the integral is nested and can be high dimensional. We propose using Multilevel Monte Carlo techniques to accelerate the computation of the nested high dimensional integral. The advantages are twofold. First, the Multilevel Monte Carlo can significantly reduce the cost of the nested integral for a given tolerance, by using an optimal sample distribution among different sample averages of the inner integrals. Second, the Multilevel Monte Carlo method imposes less assumptions, such as the concentration of measures, required by Laplace method. We test our Multilevel Monte Carlo technique using a numerical example on the design of sensor deployment for a Darcy flow problem governed by one dimensional Laplace equation. We also compare the performance of the Multilevel Monte Carlo, Laplace approximation and direct double loop Monte Carlo.

Experimental design: Case studies of diagnostics optimization for W7-X

International Nuclear Information System (INIS)

Dreier, H.; Dinklage, A.; Fischer, R.; Hartfuss, H.-J.; Hirsch, M.; Kornejew, P.; Pasch, E.; Turkin, Yu.

2005-01-01

The preparation of diagnostics for Wendelstein 7-X is accompanied by diagnostics simulations and optimization. Starting from the physical objectives, the design of diagnostics should incorporate predictive modelling (e.g. transport modelling) and simulations of respective measurements. Although technical constraints are governing design considerations, it appears that several design parameters of different diagnostics can be optimized. However, a general formulation for fusion diagnostics design in terms of optimization is lacking. In this paper, first case studies of Bayesian experimental design aiming at applications on W7-X diagnostics preparation are presented. The information gain of a measurement is formulated as a utility function which is expressed in terms of the Kullback-Leibler divergence. Then, the expected range of data is to be included and the resulting expected utility represents the objective for optimization. Bayesian probability theory gives a framework allowing us for an appropriate formulation of the design problem in terms of probability distribution functions. Results are obtained for the information gain from interferometry and for the design of polychromators for Thomson scattering. For interferometry, studies of the choice of line-of-sights for optimum signal and for the reproduction of gradient positions are presented for circular, elliptical and W7-X geometries. For Thomson scattering, the design of filter transmissions for density and temperature measurements are discussed. (author)

Study design elements for rigorous quasi-experimental comparative effectiveness research.

Science.gov (United States)

Maciejewski, Matthew L; Curtis, Lesley H; Dowd, Bryan

2013-03-01

Quasi-experiments are likely to be the workhorse study design used to generate evidence about the comparative effectiveness of alternative treatments, because of their feasibility, timeliness, affordability and external validity compared with randomized trials. In this review, we outline potential sources of discordance in results between quasi-experiments and experiments, review study design choices that can improve the internal validity of quasi-experiments, and outline innovative data linkage strategies that may be particularly useful in quasi-experimental comparative effectiveness research. There is an urgent need to resolve the debate about the evidentiary value of quasi-experiments since equal consideration of rigorous quasi-experiments will broaden the base of evidence that can be brought to bear in clinical decision-making and governmental policy-making.

Increased performance in a bottom-up designed robot by experimentally guided redesign

DEFF Research Database (Denmark)

Larsen, Jørgen Christian

2013-01-01

Purpose – Using a bottom-up, model-free approach when building robots is often seen as a less scientific way, compared to a top-down model-based approach, because the results are not easily generalizable to other systems. The authors, however, hypothesize that this problem may be addressed by using...... the bottom-up, mode-free approach, the authors used the robotic construction kit, LocoKit. This construction kit allows researchers to construct legged robots, without having a mathematical model beforehand. The authors used no specific mathematical model to design the robot, but instead used intuition...... solid experimental methods. The purpose of this paper is to show how well-known experimental methods from bio-mechanics are used to measure and locate weaknesses in a bottom-up, model-free implementation of a quadruped walker and come up with a better solution. Design/methodology/approach – To study...

Experimental and theoretical analysis for improved microscope design of optical projection tomographic microscopy.

Science.gov (United States)

Coe, Ryan L; Seibel, Eric J

2013-09-01

We present theoretical and experimental results of axial displacement of objects relative to a fixed condenser focal plane (FP) in optical projection tomographic microscopy (OPTM). OPTM produces three-dimensional, reconstructed images of single cells from two-dimensional projections. The cell rotates in a microcapillary to acquire projections from different perspectives where the objective FP is scanned through the cell while the condenser FP remains fixed at the center of the microcapillary. This work uses a combination of experimental and theoretical methods to improve the OPTM instrument design.

COMPARISON OF EXPERIMENTAL-DESIGNS COMBINING PROCESS AND MIXTURE VARIABLES .2. DESIGN EVALUATION ON MEASURED DATA

NARCIS (Netherlands)

DUINEVELD, C. A. A.; Smilde, A. K.; Doornbos, D. A.

1993-01-01

The construction of a small experimental design for a combination of process and mixture variables is a problem which has not been solved completely by now. In a previous paper we evaluated some designs with theoretical measures. This second paper evaluates the capabilities of the best of these

COMPARISON OF EXPERIMENTAL-DESIGNS COMBINING PROCESS AND MIXTURE VARIABLES .2. DESIGN EVALUATION ON MEASURED DATA

NARCIS (Netherlands)

DUINEVELD, CAA; SMILDE, AK; DOORNBOS, DA

The construction of a small experimental design for a combination of process and mixture variables is a problem which has not been solved completely by now. In a previous paper we evaluated some designs with theoretical measures. This second paper evaluates the capabilities of the best of these

Phase diagram Fe-Sn-Sr. New experimental results

International Nuclear Information System (INIS)

Nieva, N; Jimenez, M.J; Gomez, A; Corvalan Moya, C; Arias, D

2012-01-01

Zr-based alloys are widely used in nuclear industry due to their specific characteristics. The information of the phase diagrams of the ternary system Fe-Zr-Sn is scarce. In this work we investigate, in a experimental way, the central and the Fe-Sn binary adjacent regions of the Fe-Sn-Zr Gibbs triangle at the temperature of 800 o C. For the experimental work, a set of seven ternary alloys was designed, produced and examined by different complementary techniques. There were performed two types of heat treatments: one of medium and another of long duration. We present a new proposal for the 800 o C isothermal section. The boundaries of the identified phases and the fields of one, two and three phases are indicated in the diagram

Time-oriented experimental design method to optimize hydrophilic matrix formulations with gelation kinetics and drug release profiles.

Science.gov (United States)

Shin, Sangmun; Choi, Du Hyung; Truong, Nguyen Khoa Viet; Kim, Nam Ah; Chu, Kyung Rok; Jeong, Seong Hoon

2011-04-04

A new experimental design methodology was developed by integrating the response surface methodology and the time series modeling. The major purposes were to identify significant factors in determining swelling and release rate from matrix tablets and their relative factor levels for optimizing the experimental responses. Properties of tablet swelling and drug release were assessed with ten factors and two default factors, a hydrophilic model drug (terazosin) and magnesium stearate, and compared with target values. The selected input control factors were arranged in a mixture simplex lattice design with 21 experimental runs. The obtained optimal settings for gelation were PEO, LH-11, Syloid, and Pharmacoat with weight ratios of 215.33 (88.50%), 5.68 (2.33%), 19.27 (7.92%), and 3.04 (1.25%), respectively. The optimal settings for drug release were PEO and citric acid with weight ratios of 191.99 (78.91%) and 51.32 (21.09%), respectively. Based on the results of matrix swelling and drug release, the optimal solutions, target values, and validation experiment results over time were similar and showed consistent patterns with very small biases. The experimental design methodology could be a very promising experimental design method to obtain maximum information with limited time and resources. It could also be very useful in formulation studies by providing a systematic and reliable screening method to characterize significant factors in the sustained release matrix tablet. Copyright © 2011 Elsevier B.V. All rights reserved.

MYRRHA/XT-ADS primary system design and experimental devices

International Nuclear Information System (INIS)

Maes, D.

2009-01-01

The EUROTRANS project is an integrated project in the Sixth European Framework Program in the context of Partitioning and Transmutation. The objective of this project is to work towards an ETD (European Transmutation Demonstration) in a step-wise manner. The first step is to carry out an advanced design of a small-scale XT-ADS (eXperimental Transmutation in an Accelerator Driven System) for realisation in a short-term (about 10 years) as well as to accomplish a generic conceptual design of EFIT (European Facility for Industrial Transmutation) for realisation in the long-term. The MYRRHA-2005 design served as a starting basis for the XT-ADS. Many options have been revisited and the framework is now set up. While the MYRRHA-2005 design was still a conceptual design, the intention is to get at the end of the EUROTRANS project (March 2009) an advanced design of the XT-ADS, albeit a first advanced design. While the design work performed during the first years of the project (2005-2006) was mainly devoted to optimise and enhance the primary and secondary system configuration according to the suggestions and contributions of our industrial partners (Ansaldo Nucleare, Areva, Suez-Tractebel) within the DM1 (Domain 1 D ESIGN ) , the last year work objectives mainly consisted of (1) the release of the Remote Handling Design Catalogue for XT-ADS and (2) the formulation of the specification of the experimental devices according to the XT-ADS objectives and adapted to the actual XT-ADS core and core support structure design; (3) the detailed calculations of the main XT-ADS primary and secondary system components

EBTS: DESIGN AND EXPERIMENTAL STUDY

International Nuclear Information System (INIS)

PIKIN, A.; ALESSI, J.; BEEBE, E.; KPONOU, A.; PRELEC, K.; KUZNETSOV, G.; TIUNOV, M.

2000-01-01

Experimental study of the BNL Electron Beam Test Stand (EBTS), which is a prototype of the Relativistic Heavy Ion Collider (RHIC) Electron Beam Ion Source (EBIS), is currently underway. The basic physics and engineering aspects of a high current EBIS implemented in EBTS are outlined and construction of its main systems is presented. Efficient transmission of a 10 A electron beam through the ion trap has been achieved. Experimental results on generation of multiply charged ions with both continuous gas and external ion injection confirm stable operation of the ion trap

Hierarchical adaptive experimental design for Gaussian process emulators

International Nuclear Information System (INIS)

Busby, Daniel

2009-01-01

Large computer simulators have usually complex and nonlinear input output functions. This complicated input output relation can be analyzed by global sensitivity analysis; however, this usually requires massive Monte Carlo simulations. To effectively reduce the number of simulations, statistical techniques such as Gaussian process emulators can be adopted. The accuracy and reliability of these emulators strongly depend on the experimental design where suitable evaluation points are selected. In this paper a new sequential design strategy called hierarchical adaptive design is proposed to obtain an accurate emulator using the least possible number of simulations. The hierarchical design proposed in this paper is tested on various standard analytic functions and on a challenging reservoir forecasting application. Comparisons with standard one-stage designs such as maximin latin hypercube designs show that the hierarchical adaptive design produces a more accurate emulator with the same number of computer experiments. Moreover a stopping criterion is proposed that enables to perform the number of simulations necessary to obtain required approximation accuracy.

Experimental Investigations of Decentralised Control Design for The Stabilisation of Rotor-Gas Bearings

DEFF Research Database (Denmark)

Theisen, Lukas Roy Svane; Galeazzi, Roberto; Niemann, Hans Henrik

2015-01-01

frequencies. Active lubrication of the journal during operations could enhance the damping and stabilisation characteristics of the sytems, and this could be achieved by means of stabilising controllers. This paper investigates the feasibility of using reduced order models obtained through Grey......-Box identification for the design of stabilising controllers, capable of enabling the active lubrication of the journal. The root locus analysis shows that two different control solutions are feasible for the dampening of the first two eigenfrequencies of the rotor-gas bearing in the horizontal and vertical...... directions. Hardening and softening P-lead controllers are designed based on the models experimentally identified, and salient features of both controllers are discussed. Both controllers are implemented and validated on the physical test rig. Experimental results confirm the validity of the proposed...

Statistical experimental design for refractory coatings

International Nuclear Information System (INIS)

McKinnon, J.A.; Standard, O.C.

2000-01-01

The production of refractory coatings on metal casting moulds is critically dependent on the development of suitable rheological characteristics, such as viscosity and thixotropy, in the initial coating slurry. In this paper, the basic concepts of mixture design and analysis are applied to the formulation of a refractory coating, with illustration by a worked example. Experimental data of coating viscosity versus composition are fitted to a statistical model to obtain a reliable method of predicting the optimal formulation of the coating. Copyright (2000) The Australian Ceramic Society

Experimental and raytrace results for throat-to-throat compound parabolic concentrators

Science.gov (United States)

Leviton, D. B.; Leitch, J. W.

1986-01-01

Compound parabolic concentrators are nonimaging cone-shaped optics with useful angular transmission characteristics. Two cones used throat-to-throat accept radiant flux within one well-defined acceptance angle and redistribute it into another. If the entrance cone is fed with Lambertian flux, the exit cone produces a beam whose half-angle is the exit cone's acceptance angle and whose cross section shows uniform irradiance from near the exit mouth to infinity. (The pair is a beam angle transformer). The design of one pair of cones is discussed, also an experiment to map the irradiance of the emergent beam, and a raytracing program which models the cones fed by Lambertian flux. Experimental results compare favorably with raytrace results.

Bithermal and isothermal experimental test design and resulting influence on the pore formation during high-temperature-induced fatigue of the alloy 800 H

International Nuclear Information System (INIS)

Hurta, S.

1991-01-01

For investigating the damaging mechanism, bithermal TMF tests have been carried out with the alloy 800H, applying fast pressure half-cycles at low temperature (e.g. 300 C) and slow tensile phases at high temperature (e.g. 700 C). The experimental data thus obtained have been compared with the results of isothermal tests performed at 700 C. Most of the experiments have been performed stress-controlled and with a constant range of plastic strain. Under this regime, deformation is induced in the case of asymmetric test design within the tensile load phase, at various constant tensile stresses each, wheras in the compressive load phase, the stress is constantly increased for compressive stress-governed testing. The results obtained from both test types show that the type of compressive load phase is the factor governing the efficiency of pore formation. (orig.) [de

Experimental results for hydrocarbon refrigerant vaporization inside brazed plate heat exchangers at high pressure

DEFF Research Database (Denmark)

Desideri, Adriano; Ommen, Torben Schmidt; Wronski, Jorrit

2016-01-01

fluids at typical working conditions of ORC systems for low temperature waste heat recovery (WHR) applications. Based on these premises, a novel testrig has been recently designed and built at the Technical University of Denmark to simulate the evaporating condition occurring in a small capacity ORC...... power unit. In this contribution the preliminary experimental results obtained from the first experimental campaign carried out on the rig are reported. HFC-134a was selected as working fluid. The experiments were carried out at saturation temperature of 60, 70 and 80 °C and inlet and outlet qualities...

Experimental design for estimating unknown groundwater pumping using genetic algorithm and reduced order model

Science.gov (United States)

Ushijima, Timothy T.; Yeh, William W.-G.

2013-10-01

An optimal experimental design algorithm is developed to select locations for a network of observation wells that provide maximum information about unknown groundwater pumping in a confined, anisotropic aquifer. The design uses a maximal information criterion that chooses, among competing designs, the design that maximizes the sum of squared sensitivities while conforming to specified design constraints. The formulated optimization problem is non-convex and contains integer variables necessitating a combinatorial search. Given a realistic large-scale model, the size of the combinatorial search required can make the problem difficult, if not impossible, to solve using traditional mathematical programming techniques. Genetic algorithms (GAs) can be used to perform the global search; however, because a GA requires a large number of calls to a groundwater model, the formulated optimization problem still may be infeasible to solve. As a result, proper orthogonal decomposition (POD) is applied to the groundwater model to reduce its dimensionality. Then, the information matrix in the full model space can be searched without solving the full model. Results from a small-scale test case show identical optimal solutions among the GA, integer programming, and exhaustive search methods. This demonstrates the GA's ability to determine the optimal solution. In addition, the results show that a GA with POD model reduction is several orders of magnitude faster in finding the optimal solution than a GA using the full model. The proposed experimental design algorithm is applied to a realistic, two-dimensional, large-scale groundwater problem. The GA converged to a solution for this large-scale problem.

Experimental study of lithium free-surface flow for IFMIF target design

International Nuclear Information System (INIS)

Kondo, H.; Fujisato, A.; Yamaoka, N.; Inoue, S.; Miyamoto, S.; Iida, T.; Nakamura, H.; Ida, M.; Matushita, I.; Muroga, T.; Horiike, H.

2006-01-01

Lithium free-surface flow experiments to verify the design of IFMIF target have been carried out at Osaka University. The present report summarizes experimental results of surface phenomena, and cavitation characteristics of the loop, so as to try to apply these results to design parameters. Waves on the lithium flow surface is similar to that on water, and can be predicted by a linear stability theory. The wave amplitude is measured by an electro-contact probe. Surface roughness on a target nozzle, caused for example by attached chemical compounds and/or wastages by erosion and corrosion, can lead to a significant loss of target flow stability as well as surface wakes. The need of a polishing manipulator or exchange of the nozzle may be anticipated. Cavitation characteristic of the loop was measured by an accelerometer. From the results, a friction factor could be estimated fort he lithium flow

New synthetic thrombin inhibitors: molecular design and experimental verification.

Directory of Open Access Journals (Sweden)

Elena I Sinauridze

Full Text Available BACKGROUND: The development of new anticoagulants is an important goal for the improvement of thromboses treatments. OBJECTIVES: The design, synthesis and experimental testing of new safe and effective small molecule direct thrombin inhibitors for intravenous administration. METHODS: Computer-aided molecular design of new thrombin inhibitors was performed using our original docking program SOL, which is based on the genetic algorithm of global energy minimization in the framework of a Merck Molecular Force Field. This program takes into account the effects of solvent. The designed molecules with the best scoring functions (calculated binding energies were synthesized and their thrombin inhibitory activity evaluated experimentally in vitro using a chromogenic substrate in a buffer system and using a thrombin generation test in isolated plasma and in vivo using the newly developed model of hemodilution-induced hypercoagulation in rats. The acute toxicities of the most promising new thrombin inhibitors were evaluated in mice, and their stabilities in aqueous solutions were measured. RESULTS: New compounds that are both effective direct thrombin inhibitors (the best K(I was 1111.1 mg/kg. A plasma-substituting solution supplemented with one of the new inhibitors prevented hypercoagulation in the rat model of hemodilution-induced hypercoagulation. Activities of the best new inhibitors in physiological saline (1 µM solutions were stable after sterilization by autoclaving, and the inhibitors remained stable at long-term storage over more than 1.5 years at room temperature and at 4°C. CONCLUSIONS: The high efficacy, stability and low acute toxicity reveal that the inhibitors that were developed may be promising for potential medical applications.

A new experimental design method to optimize formulations focusing on a lubricant for hydrophilic matrix tablets.

Science.gov (United States)

Choi, Du Hyung; Shin, Sangmun; Khoa Viet Truong, Nguyen; Jeong, Seong Hoon

2012-09-01

A robust experimental design method was developed with the well-established response surface methodology and time series modeling to facilitate the formulation development process with magnesium stearate incorporated into hydrophilic matrix tablets. Two directional analyses and a time-oriented model were utilized to optimize the experimental responses. Evaluations of tablet gelation and drug release were conducted with two factors x₁ and x₂: one was a formulation factor (the amount of magnesium stearate) and the other was a processing factor (mixing time), respectively. Moreover, different batch sizes (100 and 500 tablet batches) were also evaluated to investigate an effect of batch size. The selected input control factors were arranged in a mixture simplex lattice design with 13 experimental runs. The obtained optimal settings of magnesium stearate for gelation were 0.46 g, 2.76 min (mixing time) for a 100 tablet batch and 1.54 g, 6.51 min for a 500 tablet batch. The optimal settings for drug release were 0.33 g, 7.99 min for a 100 tablet batch and 1.54 g, 6.51 min for a 500 tablet batch. The exact ratio and mixing time of magnesium stearate could be formulated according to the resulting hydrophilic matrix tablet properties. The newly designed experimental method provided very useful information for characterizing significant factors and hence to obtain optimum formulations allowing for a systematic and reliable experimental design method.

Experimental Design of Electrocoagulation and Magnetic Technology for Enhancing Suspended Solids Removal from Synthetic Wastewater

Directory of Open Access Journals (Sweden)

Moh Faiqun Ni'am

2014-10-01

Full Text Available Design of experiments (DOE is one of the statistical method that is used as a tool to enhance and improve experimental quality. The changes to the variables of a process or system is supposed to give the optimal result (response and quite satisfactory. Experimental design can defined as a test or series of test series by varying the input variables (factors of a process that can known to cause changes in output (response. This paper presents the results of experimental design of wastewater treatment by electrocoagulation (EC technique. A combined magnet and electrocoagulation (EC technology were designed to increase settling velocity and to enhance suspended solid removal efficiencies from wastewater samples. In this experiment, a synthetic wastewater samples were prepared by mixing 700 mg of the milk powder in one litre of water and treated by using an acidic buffer solution. The monopolar iron (Fe plate anodes and cathodes were employed as electrodes. Direct current was varied in a range of between 0.5 and 1.1 A, and flowrate in a range of between 1.00 to 3.50 mL/s. One permanent magnets namely AlNiCo with a magnetic strength of 0.16T was used in this experiment. The results show that the magnetic field and the flowrate have major influences on suspended solids removal. The efficiency removals of suspended solids, turbidity and COD removal efficiencies at optimum conditions were found to be more than 85%, 95%, and 75%, respectively.

SCRAED - Simple and Complex Random Assignment in Experimental Designs

OpenAIRE

Alferes, Valentim R.

2009-01-01

SCRAED is a package of 37 self-contained SPSS syntax files that performs simple and complex random assignment in experimental designs. For between-subjects designs, SCRAED includes simple random assignment (no restrictions, forced equal sizes, forced unequal sizes, and unequal probabilities), block random assignment (simple and generalized blocks), and stratified random assignment (no restrictions, forced equal sizes, forced unequal sizes, and unequal probabilities). For within-subject...

Randomizing Roaches: Exploring the "Bugs" of Randomization in Experimental Design

Science.gov (United States)

Wagler, Amy; Wagler, Ron

2014-01-01

Understanding the roles of random selection and random assignment in experimental design is a central learning objective in most introductory statistics courses. This article describes an activity, appropriate for a high school or introductory statistics course, designed to teach the concepts, values and pitfalls of random selection and assignment…

Bias Corrections for Standardized Effect Size Estimates Used with Single-Subject Experimental Designs

Science.gov (United States)

Ugille, Maaike; Moeyaert, Mariola; Beretvas, S. Natasha; Ferron, John M.; Van den Noortgate, Wim

2014-01-01

A multilevel meta-analysis can combine the results of several single-subject experimental design studies. However, the estimated effects are biased if the effect sizes are standardized and the number of measurement occasions is small. In this study, the authors investigated 4 approaches to correct for this bias. First, the standardized effect…

Providing guidance in virtual lab experimentation : the case of an experiment design tool

NARCIS (Netherlands)

Efstathiou, Charalampos; Hovardas, Tasos; Xenofontos, Nikoletta A.; Zacharia, Zacharias C.; de Jong, Ton A.J.M.; Anjewierden, Anjo; van Riesen, Siswa A.N.

2018-01-01

The present study employed a quasi-experimental design to assess a computer-based tool, which was intended to scaffold the task of designing experiments when using a virtual lab for the process of experimentation. In particular, we assessed the impact of this tool on primary school students’

Pressure suppression system (PSS) for nuclear ships. Experimental results obtained at the GKSS PSS-test-facillity

International Nuclear Information System (INIS)

Aust, E.; Niemann, H.R.; Schwan, H.; Vollbrandt, J.

1978-01-01

The PSS-test facility is shortly presented which was designed to show experimentally the operation of the pressure suppression containment for the NCS 80 concept. The results of the experimental LOCA-simulation tests in the PSS-test facility are illustrated by diagrams. The observed phenomena as chugging and pessure oscillations immediately after vent clearing are reported as well as the thermohydraulic loadings of the total system. Finally a short view is given on the future test program

Optimal design and experimental analyses of a new micro-vibration control payload-platform

Science.gov (United States)

Sun, Xiaoqing; Yang, Bintang; Zhao, Long; Sun, Xiaofen

2016-07-01

This paper presents a new payload-platform, for precision devices, which possesses the capability of isolating the complex space micro-vibration in low frequency range below 5 Hz. The novel payload-platform equipped with smart material actuators is investigated and designed through optimization strategy based on the minimum energy loss rate, for the aim of achieving high drive efficiency and reducing the effect of the magnetic circuit nonlinearity. Then, the dynamic model of the driving element is established by using the Lagrange method and the performance of the designed payload-platform is further discussed through the combination of the controlled auto regressive moving average (CARMA) model with modified generalized prediction control (MGPC) algorithm. Finally, an experimental prototype is developed and tested. The experimental results demonstrate that the payload-platform has an impressive potential of micro-vibration isolation.

Combustion synthesis of TiB2-based cermets: modeling and experimental results

International Nuclear Information System (INIS)

Martinez Pacheco, M.; Bouma, R.H.B.; Katgerman, L.

2008-01-01

TiB 2 -based cermets are prepared by combustion synthesis followed by a pressing stage in a granulate medium. Products obtained by combustion synthesis are characterized by a large remaining porosity (typically 50%). To produce dense cermets, a subsequent densification step is performed after the combustion process and when the reacted material is still hot. To design the process, numerical simulations are carried out and compared to experimental results. In addition, physical and electrical properties of the products related to electrical contact applications are evaluated. (orig.)

Experimental design and analysis for piezoelectric circular actuators in flow control applications

International Nuclear Information System (INIS)

Mane, Poorna; Mossi, Karla; Bryant, Robert

2008-01-01

Flow control can lead to saving millions of dollars in fuel costs each year by making an aircraft more efficient. Synthetic jets, a device for active flow control, operate by introducing small amounts of energy locally to achieve non-local changes in the flow field with large performance gains. These devices consist of a cavity with an oscillating diaphragm that divides it into active and passive sides. The active side has a small opening where a jet is formed, while the passive side does not directly participate in the fluidic jet. Over the years, research has shown that synthetic jet behavior is dependent on the active diaphragm and the cavity design; hence, the focus of this work. The performance of the synthetic jet is studied under various factors related to the diaphragm and the cavity geometry. Three diaphragms, manufactured from piezoelectric composites, were selected for this study: Bimorph, Thunder ® and Lipca. The overall factors considered are the driving signals, voltage, frequency, cavity height, orifice size, and passive cavity pressure. Using the average maximum jet velocity as the response variable, these factors are individually studied for each actuator, and statistical analysis tools are used to select the relevant factors in the response variable. The factors are divided into two experimental fractional factorial design matrices, with five and four factors, respectively. Both experiments are chosen to be of resolution V, where main factors are confounded with three-factor interactions. In the first experimental design, the results show that frequency is not a significant factor, while waveform is significant for all the actuators. In addition, the magnitude of the regression coefficients suggests that a model that includes the diaphragm as a factor may be possible. These results are valid within the ranges tested, that is low frequencies and sawtooth and sine waveform as driving signals. In the second experimental design, cavity dimensions are

Scaffolded Instruction Improves Student Understanding of the Scientific Method & Experimental Design

Science.gov (United States)

D'Costa, Allison R.; Schlueter, Mark A.

2013-01-01

Implementation of a guided-inquiry lab in introductory biology classes, along with scaffolded instruction, improved students' understanding of the scientific method, their ability to design an experiment, and their identification of experimental variables. Pre- and postassessments from experimental versus control sections over three semesters…

Design preferences and cognitive styles: experimentation by automated website synthesis.

Science.gov (United States)

Leung, Siu-Wai; Lee, John; Johnson, Chris; Robertson, David

2012-06-29

This article aims to demonstrate computational synthesis of Web-based experiments in undertaking experimentation on relationships among the participants' design preference, rationale, and cognitive test performance. The exemplified experiments were computationally synthesised, including the websites as materials, experiment protocols as methods, and cognitive tests as protocol modules. This work also exemplifies the use of a website synthesiser as an essential instrument enabling the participants to explore different possible designs, which were generated on the fly, before selection of preferred designs. The participants were given interactive tree and table generators so that they could explore some different ways of presenting causality information in tables and trees as the visualisation formats. The participants gave their preference ratings for the available designs, as well as their rationale (criteria) for their design decisions. The participants were also asked to take four cognitive tests, which focus on the aspects of visualisation and analogy-making. The relationships among preference ratings, rationale, and the results of cognitive tests were analysed by conservative non-parametric statistics including Wilcoxon test, Krustal-Wallis test, and Kendall correlation. In the test, 41 of the total 64 participants preferred graphical (tree-form) to tabular presentation. Despite the popular preference for graphical presentation, the given tabular presentation was generally rated to be easier than graphical presentation to interpret, especially by those who were scored lower in the visualization and analogy-making tests. This piece of evidence helps generate a hypothesis that design preferences are related to specific cognitive abilities. Without the use of computational synthesis, the experiment setup and scientific results would be impractical to obtain.

A quasi-experimental design based on regional variations: discussion of a method for evaluating outcomes of medical practice

DEFF Research Database (Denmark)

Loft, A; Andersen, T F; Madsen, Mette

1989-01-01

A large proportion of common medical practices are subject to substantial regional variation resulting in numerous natural experiments. Opportunities are thereby provided for outcome evaluation through quasi-experimental design. If patients treated in different regions were comparable a natural...... experiment involving alternative treatments could be regarded as 'pseudo randomised', but empirical investigations are needed to verify this prerequisite. This paper discusses the role of quasi-experimental designs in assessment of medical care with evaluation of outcomes after hysterectomy in Denmark...... groups are elicited from administrative data. We conclude that it is possible to establish a quasi-experimental design based on regional variations and that the comparability of the groups included may be assessed through registry data. The importance of technology diffusion for the prospects...

Optimal Experimental Design for Large-Scale Bayesian Inverse Problems

KAUST Repository

Ghattas, Omar

2014-01-01

We develop a Bayesian framework for the optimal experimental design of the shock tube experiments which are being carried out at the KAUST Clean Combustion Research Center. The unknown parameters are the pre-exponential parameters and the activation

Experimental on-line platform for product conceptual design: OpenDesigNet

Directory of Open Access Journals (Sweden)

Teresa Magal-Royo

2013-09-01

Full Text Available This paper highlights the need for using specialised on-line collaborative environments by designers and product engineers who increasingly use Web 2.0 technology to search for information. Although there are professional channels and networks, there is no specific platform which helps during a new product’s conceptualisation phase. Open communication must thus be promoted and encouraged amongst design professionals and companies to form working groups thereby allowing them to work collaboratively in the most open and creative phase of product design, i.e. conceptualisation. The OpenDesigNet (ODN experimental platform has been developed so that designers and small- or medium-sized companies (SMC can access on-line collaborative tools to support the creation and promotion of new on-line products and assess their immediate social impact. This article presents some of the results obtained during the validation phase involving a platform satisfaction survey of design engineering students and has led to a first-hand assessment of the new platform’s potential impact on their professional future.

Present activities for the preparation of a Japanese draft of structural design guidelines for the experimental fusion reactor

International Nuclear Information System (INIS)

Miya, K.; Muto, Y.; Takatsu, H.; Hada, K.; Koizumi, K.; Jitsukawa, S.; Arai, T.; Ohkawa, Y.; Shimakawa, T.; Aoto, K.; Shiraishi, H.; Takagi, T.; Miki, N.; Takahashi, S.; Sato, K.; Takemasa, F.; Kasaba, M.; Kudough, F.; Fujita, J.; Kajiura, S.; Kinoshita, S.

1996-01-01

Since November 1990, systematic research has been carried out in preparation for a Japanese draft of structural design guidelines for the experimental fusion reactor. This report summarizes the major results of the work and the status of these efforts. A classification of components and definition of operating conditions are proposed on the basis of the ITER-CDA design, in the light of the safety characteristics of the fusion reactor and relevant conventions for the existing fission reactor design code. Specific issues regarding the structural design of the experimental fusion reactor are discussed based on the experimental and analytical work. The validity of the existing structural design method is confirmed for the use of irradiated 316 SS, irrespective of the significant reduction in uniform elongation capability caused by heavy neutron irradiation. Further important phenomena are treated such as magnetic damping, magnetic stiffness and fracture due to electromagnetic forces. Finally, the issues concerned with welding and non-destructive examinations are discussed with relevance to component classification. (orig.)

He-cooled divertor for DEMO: Experimental verification of the conceptual modular design

International Nuclear Information System (INIS)

Norajitra, P.; Gervash, A.; Giniyatulin, R.; Ihli, T.; Krauss, W.; Kruessmann, R.; Kuznetsov, V.; Makhankov, A.; Mazul, I.; Ovchinnikov, I.

2006-01-01

A modular He-cooled divertor concept is being developed at the Forschungszentrum Karlsruhe. The design goal is to withstand a high heat flux of 10 MW/m 2 at least. The work programme of 2004 focused on experiments to verify the design and thermohydraulics layout. In cooperation with the Efremov Institute, experimental investigations were performed for the joining of tungsten parts and/or tungsten parts with steel and the fabrication of divertor components from tungsten. Moreover, gas puffing experiments were carried out with a stationary approach to measuring pressure loss and heat transfer for the purpose of screening the design options and verifying the computational fluid dynamics (CFD) calculations. The status and results of the technological and helium experiments shall be outlined in this report

Electrochemical production and use of free chlorine for pollutant removal: an experimental design approach.

Science.gov (United States)

Antonelli, Raissa; de Araújo, Karla Santos; Pires, Ricardo Francisco; Fornazari, Ana Luiza de Toledo; Granato, Ana Claudia; Malpass, Geoffroy Roger Pointer

2017-10-28

The present paper presents the study of (1) the optimization of electrochemical-free chlorine production using an experimental design approach, and (2) the application of the optimum conditions obtained for the application in photo-assisted electrochemical degradation of simulated textile effluent. In the experimental design the influence of inter-electrode gap, pH, NaCl concentration and current was considered. It was observed that the four variables studied are significant for the process, with NaCl concentration and current being the most significant variables for free chlorine production. The maximum free chlorine production was obtained at a current of 2.33 A and NaCl concentrations in 0.96 mol dm -3 . The application of the optimized conditions with simultaneous UV irradiation resulted in up to 83.1% Total Organic Carbon removal and 100% of colour removal over 180 min of electrolysis. The results indicate that a systematic (statistical) approach to the electrochemical treatment of pollutants can save time and reagents.

Design and application on experimental platform for high-speed bearing with grease lubrication

Directory of Open Access Journals (Sweden)

He Qiang

2015-12-01

Full Text Available The experimental platform for high-speed grease is an important tool for research and development of high-speed motorized spindle with grease lubrication. In this article, the experimental platform for high-speed grease is designed and manufactured which consists of the drive system, the test portion, the loading system, the lubrication system, the control system, and so on. In the meantime, the high-speed angular contact ceramic ball bearings B7005C/HQ1P4 as the research object are tested and contrasted in the grease lubrication and oil mist lubrication. The experimental platform performance is validated by contrast experiment, and the high-speed lubricated bearing performance is also studied especially in the relationship among the rotating speed,load and temperature rise. The results show that the experimental platform works steadily, accurate, and reliable in the experimental testing. And the grease lubrication ceramic ball bearings B7005C/HQ1P4 can be used in high-speed motorized spindle in the circular water cooling conditions when the rotating speed is lower than 40,000 r/min or the DN value (the value of the bearing diameter times the rotating speed is lower than the 1.44 × 106 mm r/min. Grease lubrication instead of oil mist lubrication under high-speed rotating will simplify the structure design of the high-speed motorized spindle and reduce the pollution to the environment.

Visual Servoing Tracking Control of a Ball and Plate System: Design, Implementation and Experimental Validation

Directory of Open Access Journals (Sweden)

Ming-Tzu Ho

2013-07-01

Full Text Available This paper presents the design, implementation and validation of real-time visual servoing tracking control for a ball and plate system. The position of the ball is measured with a machine vision system. The image processing algorithms of the machine vision system are pipelined and implemented on a field programmable gate array (FPGA device to meet real-time constraints. A detailed dynamic model of the system is derived for the simulation study. By neglecting the high-order coupling terms, the ball and plate system model is simplified into two decoupled ball and beam systems, and an approximate input-output feedback linearization approach is then used to design the controller for trajectory tracking. The designed control law is implemented on a digital signal processor (DSP. The validity of the performance of the developed control system is investigated through simulation and experimental studies. Experimental results show that the designed system functions well with reasonable agreement with simulations.

Computational design and experimental validation of new thermal barrier systems

Energy Technology Data Exchange (ETDEWEB)

Guo, Shengmin [Louisiana State Univ., Baton Rouge, LA (United States)

2015-03-31

The focus of this project is on the development of a reliable and efficient ab initio based computational high temperature material design method which can be used to assist the Thermal Barrier Coating (TBC) bond-coat and top-coat design. Experimental evaluations on the new TBCs are conducted to confirm the new TBCs’ properties. Southern University is the subcontractor on this project with a focus on the computational simulation method development. We have performed ab initio density functional theory (DFT) method and molecular dynamics simulation on screening the top coats and bond coats for gas turbine thermal barrier coating design and validation applications. For experimental validations, our focus is on the hot corrosion performance of different TBC systems. For example, for one of the top coatings studied, we examined the thermal stability of TaZr_2.75O₈ and confirmed it’s hot corrosion performance.

Design and Experimental Study of an Over-Under TBCC Exhaust System.

Science.gov (United States)

Mo, Jianwei; Xu, Jinglei; Zhang, Liuhuan

2014-01-01

Turbine-based combined-cycle (TBCC) propulsion systems have been a topic of research as a means for more efficient flight at supersonic and hypersonic speeds. The present study focuses on the fundamental physics of the complex flow in the TBCC exhaust system during the transition mode as the turbine exhaust is shut off and the ramjet exhaust is increased. A TBCC exhaust system was designed using methods of characteristics (MOC) and subjected to experimental and computational study. The main objectives of the study were: (1) to identify the interactions between the two exhaust jet streams during the transition mode phase and their effects on the whole flow-field structure; (2) to determine and verify the aerodynamic performance of the over-under TBCC exhaust nozzle; and (3) to validate the simulation ability of the computational fluid dynamics (CFD) software according to the experimental conditions. Static pressure taps and Schlieren apparatus were employed to obtain the wall pressure distributions and flow-field structures. Steady-state tests were performed with the ramjet nozzle cowl at six different positions at which the turbine flow path were half closed and fully opened, respectively. Methods of CFD were used to simulate the exhaust flow and they complemented the experimental study by providing greater insight into the details of the flow field and a means of verifying the experimental results. Results indicated that the flow structure was complicated because the two exhaust jet streams interacted with each other during the exhaust system mode transition. The exhaust system thrust coefficient varied from 0.9288 to 0.9657 during the process. The CFD simulation results agree well with the experimental data, which demonstrated that the CFD methods were effective in evaluating the aerodynamic performance of the TBCC exhaust system during the mode transition.

The emergence of modern statistics in agricultural science: analysis of variance, experimental design and the reshaping of research at Rothamsted Experimental Station, 1919-1933.

Science.gov (United States)

Parolini, Giuditta

2015-01-01

During the twentieth century statistical methods have transformed research in the experimental and social sciences. Qualitative evidence has largely been replaced by quantitative results and the tools of statistical inference have helped foster a new ideal of objectivity in scientific knowledge. The paper will investigate this transformation by considering the genesis of analysis of variance and experimental design, statistical methods nowadays taught in every elementary course of statistics for the experimental and social sciences. These methods were developed by the mathematician and geneticist R. A. Fisher during the 1920s, while he was working at Rothamsted Experimental Station, where agricultural research was in turn reshaped by Fisher's methods. Analysis of variance and experimental design required new practices and instruments in field and laboratory research, and imposed a redistribution of expertise among statisticians, experimental scientists and the farm staff. On the other hand the use of statistical methods in agricultural science called for a systematization of information management and made computing an activity integral to the experimental research done at Rothamsted, permanently integrating the statisticians' tools and expertise into the station research programme. Fisher's statistical methods did not remain confined within agricultural research and by the end of the 1950s they had come to stay in psychology, sociology, education, chemistry, medicine, engineering, economics, quality control, just to mention a few of the disciplines which adopted them.

Quasi-experimental designs in practice-based research settings: design and implementation considerations.

Science.gov (United States)

Handley, Margaret A; Schillinger, Dean; Shiboski, Stephen

2011-01-01

Although randomized controlled trials are often a gold standard for determining intervention effects, in the area of practice-based research (PBR), there are many situations in which individual randomization is not possible. Alternative approaches to evaluating interventions have received increased attention, particularly those that can retain elements of randomization such that they can be considered "controlled" trials. Methodological design elements and practical implementation considerations for two quasi-experimental design approaches that have considerable promise in PBR settings--the stepped-wedge design, and a variant of this design, a wait-list cross-over design, are presented along with a case study from a recent PBR intervention for patients with diabetes. PBR-relevant design features include: creation of a cohort over time that collects control data but allows all participants (clusters or patients) to receive the intervention; staggered introduction of clusters; multiple data collection points; and one-way cross-over into the intervention arm. Practical considerations include: randomization versus stratification, training run in phases; and extended time period for overall study completion. Several design features of practice based research studies can be adapted to local circumstances yet retain elements to improve methodological rigor. Studies that utilize these methods, such as the stepped-wedge design and the wait-list cross-over design, can increase the evidence base for controlled studies conducted within the complex environment of PBR.

Integration of CFD and Experimental Results at VKI in Low-Speed Aerodynamic Design

Science.gov (United States)

2007-06-01

erosion in wind tunnel behind the building Today, almost all modern Antartic stations have undergone aerodynamic studies at different stages of design...2] J. Sanz Rodrigo, C. Gorle, J. van Beeck, P. Planquart: Aerodynamic Design of the Princess Elizabeth Antartic Research Station, 17th

ANOVA parameters influence in LCF experimental data and simulation results

Directory of Open Access Journals (Sweden)

Vercelli A.

2010-06-01

Full Text Available The virtual design of components undergoing thermo mechanical fatigue (TMF and plastic strains is usually run in many phases. The numerical finite element method gives a useful instrument which becomes increasingly effective as the geometrical and numerical modelling gets more accurate. The constitutive model definition plays an important role in the effectiveness of the numerical simulation [1, 2] as, for example, shown in Figure 1. In this picture it is shown how a good cyclic plasticity constitutive model can simulate a cyclic load experiment. The component life estimation is the subsequent phase and it needs complex damage and life estimation models [3-5] which take into account of several parameters and phenomena contributing to damage and life duration. The calibration of these constitutive and damage models requires an accurate testing activity. In the present paper the main topic of the research activity is to investigate whether the parameters, which result to be influent in the experimental activity, influence the numerical simulations, thus defining the effectiveness of the models in taking into account of all the phenomena actually influencing the life of the component. To obtain this aim a procedure to tune the parameters needed to estimate the life of mechanical components undergoing TMF and plastic strains is presented for commercial steel. This procedure aims to be easy and to allow calibrating both material constitutive model (for the numerical structural simulation and the damage and life model (for life assessment. The procedure has been applied to specimens. The experimental activity has been developed on three sets of tests run at several temperatures: static tests, high cycle fatigue (HCF tests, low cycle fatigue (LCF tests. The numerical structural FEM simulations have been run on a commercial non linear solver, ABAQUS®6.8. The simulations replied the experimental tests. The stress, strain, thermal results from the thermo

Overview of design development of FCC-hh Experimental Interaction Regions

CERN Document Server

AUTHOR|(CDS)2082479; Abelleira, Jose; Cruz Alaniz, Emilia; Van Riesen-Haupt, Leon; Benedikt, Michael; Besana, Maria Ilaria; Buffat, Xavier; Burkhardt, Helmut; Cerutti, Francesco; Langner, Andy Sven; Martin, Roman; Riegler, Werner; Schulte, Daniel; Tomas Garcia, Rogelio; Appleby, Robert Barrie; Rafique, Haroon; Barranco Garcia, Javier; Pieloni, Tatiana; Boscolo, Manuela; Collamati, Francesco; Nevay, Laurence James; Hofer, Michael

2017-01-01

The experimental interaction region (EIR) is one of the key areas that define the performance of the Future Circular Collider. In this overview we will describe the status and the evolution of the design of EIR of FCC-hh, focusing on design of the optics, energy deposition in EIR elements, beam-beam effects and machine detector interface issues.

Second preliminary design of JAERI experimental fusion reactor (JXFR)

International Nuclear Information System (INIS)

Sako, Kiyoshi; Tone, Tatsuzo; Seki, Yasushi; Iida, Hiromasa; Yamato, Harumi

1979-06-01

Second preliminary design of a tokamak experimental fusion reactor to be built in the near future has been performed. This design covers overall reactor system including plasma characteristics, reactor structure, blanket neutronics radiation shielding, superconducting magnets, neutral beam injector, electric power supply system, fuel recirculating system, reactor cooling and tritium recovery systems and maintenance scheme. Safety analyses of the reactor system have been also performed. This paper gives a brief description of the design as of January, 1979. The feasibility study of raising the power density has been also studied and is shown as appendix. (author)

First preliminary design of an experimental fusion reactor

International Nuclear Information System (INIS)

1977-09-01

A preliminary design of a tokamak experimental fusion reactor to be built in the near future is under way. The goals of the reactor are to achieve reactor-level plasma conditions for a sufficiently long operation period and to obtain design, construction and operational experience for the main components of full-scale power reactors. This design covers overall reactor system including plasma characteristics, reactor structure, blanket neutronics, shielding, superconducting magnets, neutral beam injector, electric power supply system, fuel circulating system, reactor cooling system, tritium recovery system and maintenance scheme. The main design parameters are as follows: the reactor fusion power 100 MW, torus radius 6.75 m, plasma radius 1.5 m, first wall radius 1.75 m, toroidal magnet field on axis 6 T, blanket fertile material Li 2 O, coolant He, structural material 316SS and tritium breeding ratio 0.9. (auth.)

Design and adjustment on test bed of replacing subassembly machine control system for China experimental fast reactor

International Nuclear Information System (INIS)

Dong Shengguo; Ma Hongsheng; Zhao Lixia

2008-01-01

The present research concerns in the design and adjustment of replacing sub- assembly machine control system of China Experimental Fast Reactor. The design of replacing subassembly machine control system adopts some electric equipments, such as programmable controllers, digital DC drivers. The designed control system was adjusted on the test bed. The results indicate that the operation of the control system is steady and reliable, and designed control system can meet the needs of the design specification. (authors)

Experimental and Numerical Design and Optimization of a Counter-Flow Heat Exchanger

Directory of Open Access Journals (Sweden)

Bahrami Salman

2018-01-01

Full Text Available A new inexpensive counter-flow heat exchanger has been designed and optimized for a vapor-compression cooling system in this research. The main aim is to experimentally and numerically evaluate the effect of an internal heat exchanger (IHX adaptation in an automotive air conditioning system. In this new design of IHX, the high-pressure liquid passes through the central channel and the low-pressure vapor flows in several parallel channels in the opposite direction. The experimental set-up has been made up of original components of the air conditioning system of a medium sedan car, specially designed and built to analyze vehicle A/C equipment under real operating conditions. The results show that this compact IHX may achieve up to 10% of the evaporator capacity while low pressure drop will be imposed on this refrigeration cycle. Also, they confirm considerable decrease of compressor power consumption (CPC, which is intensified at higher evaporator air flow. A significant improvement of the coefficient of performance (COP is achieved with the IHX employment too. The influence of operating conditions has been also discussed in this paper. Finally, numerical analyses have been briefly presented, which bring more details of the flow behavior and heat transfer phenomena, and help to determine the optimal arrangement of channels.

Development and verification test of integral reactor major components - Development of MCP impeller design, performance prediction code and experimental verification

Energy Technology Data Exchange (ETDEWEB)

Chung, Myung Kyoon; Oh, Woo Hyoung; Song, Jae Wook [Korea Advanced Institute of Science and Technology, Taejon (Korea)

1999-03-01

The present study is aimed at developing a computational code for design and performance prediction of an axial-flow pump. The proposed performance prediction method is tested against a model axial-flow pump streamline curvature method. The preliminary design is made by using the ideal velocity triangles at inlet and exit and the three dimensional blade shape is calculated by employing the free vortex design method. Then the detailed blading design is carried out by using experimental database of double circular arc cambered hydrofoils. To computationally determine the design incidence, deviation, blade camber, solidity and stagger angle, a number of correlation equations are developed form the experimental database and a theorical formula for the lift coefficient is adopted. A total of 8 equations are solved iteratively using an under-relaxation factor. An experimental measurement is conducted under a non-cavitating condition to obtain the off-design performance curve and also a cavitation test is carried out by reducing the suction pressure. The experimental results are very satisfactorily compared with the predictions by the streamline curvature method. 28 refs., 26 figs., 11 tabs. (Author)

Experimental Designs Exercises and Solutions

CERN Document Server

Kabe, DG

2007-01-01

This volume provides a collection of exercises together with their solutions in design and analysis of experiments. The theoretical results, essential for understanding, are given first. These exercises have been collected during the authors teaching courses over a long period of time. These are particularly helpful to the students studying the design of experiments and instructors and researchers engaged in the teaching and research of design by experiment.

Multi-objective experimental design for (13)C-based metabolic flux analysis.

Science.gov (United States)

Bouvin, Jeroen; Cajot, Simon; D'Huys, Pieter-Jan; Ampofo-Asiama, Jerry; Anné, Jozef; Van Impe, Jan; Geeraerd, Annemie; Bernaerts, Kristel

2015-10-01

(13)C-based metabolic flux analysis is an excellent technique to resolve fluxes in the central carbon metabolism but costs can be significant when using specialized tracers. This work presents a framework for cost-effective design of (13)C-tracer experiments, illustrated on two different networks. Linear and non-linear optimal input mixtures are computed for networks for Streptomyces lividans and a carcinoma cell line. If only glucose tracers are considered as labeled substrate for a carcinoma cell line or S. lividans, the best parameter estimation accuracy is obtained by mixtures containing high amounts of 1,2-(13)C2 glucose combined with uniformly labeled glucose. Experimental designs are evaluated based on a linear (D-criterion) and non-linear approach (S-criterion). Both approaches generate almost the same input mixture, however, the linear approach is favored due to its low computational effort. The high amount of 1,2-(13)C2 glucose in the optimal designs coincides with a high experimental cost, which is further enhanced when labeling is introduced in glutamine and aspartate tracers. Multi-objective optimization gives the possibility to assess experimental quality and cost at the same time and can reveal excellent compromise experiments. For example, the combination of 100% 1,2-(13)C2 glucose with 100% position one labeled glutamine and the combination of 100% 1,2-(13)C2 glucose with 100% uniformly labeled glutamine perform equally well for the carcinoma cell line, but the first mixture offers a decrease in cost of $ 120 per ml-scale cell culture experiment. We demonstrated the validity of a multi-objective linear approach to perform optimal experimental designs for the non-linear problem of (13)C-metabolic flux analysis. Tools and a workflow are provided to perform multi-objective design. The effortless calculation of the D-criterion can be exploited to perform high-throughput screening of possible (13)C-tracers, while the illustrated benefit of multi

Predictions of High Energy Experimental Results

Directory of Open Access Journals (Sweden)

Comay E.

2010-10-01

Full Text Available Eight predictions of high energy experimental results are presented. The predictions contain the $Sigma ^+$ charge radius and results of two kinds of experiments using energetic pionic beams. In addition, predictions of the failure to find the following objects are presented: glueballs, pentaquarks, Strange Quark Matter, magnetic monopoles searched by their direct interaction with charges and the Higgs boson. The first seven predictions rely on the Regular Charge-Monopole Theory and the last one relies on mathematical inconsistencies of the Higgs Lagrangian density.

Tilted wheel satellite attitude control with air-bearing table experimental results

Science.gov (United States)

Inumoh, Lawrence O.; Forshaw, Jason L.; Horri, Nadjim M.

2015-12-01

Gyroscopic actuators for satellite control have attracted significant research interest over the years, but their viability for the control of small satellites has only recently started to become clear. Research on variable speed gyroscopic actuators has long been focused on single gimbal actuators; double gimbal actuators typically operate at constant wheel spin rate and allow tilt angle ranges far larger than the ranges needed to operate most satellite missions. This research examines a tilted wheel, a newly proposed type of inertial actuator that can generate torques in all three principal axes of a rigid satellite using a spinning wheel and a double tilt mechanism. The tilt mechanism tilts the angular momentum vector about two axes providing two degree of freedom control, while variation of the wheel speed provides the third. The equations of motion of the system lead to a singularity-free system during nominal operation avoiding the need for complex steering logic. This paper describes the hardware design of the tilted wheel and the experimental setup behind both standalone and spherical air-bearing tables used to test it. Experimental results from the air bearing table are provided with the results depicting the high performance capabilities of the proposed actuator in torque generation.

ITER [International Thermonuclear Experimental Reactor] reactor building design study

International Nuclear Information System (INIS)

Thomson, S.L.; Blevins, J.D.; Delisle, M.W.

1989-01-01

The International Thermonuclear Experimental Reactor (ITER) is at the midpoint of a two-year conceptual design. The ITER reactor building is a reinforced concrete structure that houses the tokamak and associated equipment and systems and forms a barrier between the tokamak and the external environment. It provides radiation shielding and controls the release of radioactive materials to the environment during both routine operations and accidents. The building protects the tokamak from external events, such as earthquakes or aircraft strikes. The reactor building requirements have been developed from the component designs and the preliminary safety analysis. The equipment requirements, tritium confinement, and biological shielding have been studied. The building design in progress requires continuous iteraction with the component and system designs and with the safety analysis. 8 figs

Measuring and Advancing Experimental Design Ability in an Introductory Course without Altering Existing Lab Curriculum

Directory of Open Access Journals (Sweden)

Ryan A. Shanks

2017-05-01

Full Text Available Introductory biology courses provide an important opportunity to prepare students for future courses, yet existing cookbook labs, although important in their own way, fail to provide many of the advantages of semester-long research experiences. Engaging, authentic research experiences aid biology students in meeting many learning goals. Therefore, overlaying a research experience onto the existing lab structure allows faculty to overcome barriers involving curricular change. Here we propose a working model for this overlay design in an introductory biology course and detail a means to conduct this lab with minimal increases in student and faculty workloads. Furthermore, we conducted exploratory factor analysis of the Experimental Design Ability Test (EDAT and uncovered two latent factors which provide valid means to assess this overlay model’s ability to increase advanced experimental design abilities. In a pre-test/post-test design, we demonstrate significant increases in both basic and advanced experimental design abilities in an experimental and comparison group. We measured significantly higher gains in advanced experimental design understanding in students in the experimental group. We believe this overlay model and EDAT factor analysis contribute a novel means to conduct and assess the effectiveness of authentic research experiences in an introductory course without major changes to the course curriculum and with minimal increases in faculty and student workloads.

Influence of Hydraulic Design on Stability and on Pressure Pulsations in Francis Turbines at Overload, Part Load and Deep Part Load based on Numerical Simulations and Experimental Model Test Results

International Nuclear Information System (INIS)

Magnoli, M V; Maiwald, M

2014-01-01

min −1 are reported, analysed and commented here. The analysis of experimental results allowed the identification of designs and configurations, which can improve the machine stability

Micro-Randomized Trials: An Experimental Design for Developing Just-in-Time Adaptive Interventions

Science.gov (United States)

Klasnja, Predrag; Hekler, Eric B.; Shiffman, Saul; Boruvka, Audrey; Almirall, Daniel; Tewari, Ambuj; Murphy, Susan A.

2015-01-01

Objective This paper presents an experimental design, the micro-randomized trial, developed to support optimization of just-in-time adaptive interventions (JITAIs). JITAIs are mHealth technologies that aim to deliver the right intervention components at the right times and locations to optimally support individuals’ health behaviors. Micro-randomized trials offer a way to optimize such interventions by enabling modeling of causal effects and time-varying effect moderation for individual intervention components within a JITAI. Methods The paper describes the micro-randomized trial design, enumerates research questions that this experimental design can help answer, and provides an overview of the data analyses that can be used to assess the causal effects of studied intervention components and investigate time-varying moderation of those effects. Results Micro-randomized trials enable causal modeling of proximal effects of the randomized intervention components and assessment of time-varying moderation of those effects. Conclusions Micro-randomized trials can help researchers understand whether their interventions are having intended effects, when and for whom they are effective, and what factors moderate the interventions’ effects, enabling creation of more effective JITAIs. PMID:26651463

LOGICAL AND EXPERIMENTAL DESIGN FOR PHENOL DEGRADATION USING IMMOBILIZED ACINETOBACTER SP. CULTURE

Directory of Open Access Journals (Sweden)

Amro Abd Al Fattah Amara

2010-05-01

Full Text Available Phenol degradation processes were conducted through a series of enzymatic reactions effects and is affect by different components of the microbial metabolic flux. Using different optimization strategies like mutagenesis could lead to a successful optimization but also lead to lost of some important microbial features or to release a new virulence or unexpected characters. Plackett-Burman closes much gab between optimization, safety, time, cost, Man/hr, the complexity of the metabolic flux etc. Using Plackett-Burman experimental design lead to map the points affect in the optimization process by well understanding their request from nutrient and the best environmental condition required. In this study nine variables include pH (X1, oC (X2, glucose (X3, yeast extract (X4, meat extract (X5, NH4NO3 (X6, K-salt (X7, Mg-salt (X8 and trace element (X9 are optimized during phenol degradation by Acinetobacter sp., using Plackett-Burman design method. Plackett-Burman included 16 experiments, each was used in two levels, [-1] low and high [+1]. According to Blackett-Burman design experiments the maximum degradation rate was 31.25 mg/l/h. Logical and statistical analysis of the data lead to select pH, Temperature and Meat extract as three factors affecting on phenol degradation rate. These three variables have been used in Box-Behnken experimental design for further optimization. Meat extract, which is not statistically recommended for optimization has been used while it can substitute trace element, which is statistically significant. Glucose, which is statistically significant, did not included while it has a negative effect and gave the best result at 0 g/l amount. Glucose has been completely omitted from the media.  pH, temperature and meat extract were used in fifteen experiments each was used in three levels, –1, 0, and +1 according to Box-Behnken design. Microsoft Excel 2002 solver tool was used to optimize the model created from Box-Behnken. The

Design Parameters of Vortex Pumps: A Meta-Analysis of Experimental Studies

Directory of Open Access Journals (Sweden)

Angela Gerlach

2017-01-01

Full Text Available Vortex pumps can impel solid-containing fluids and are therefore widely applied, from wastewater transport to the food industry. Despite constant efforts to improve vortex pumps, however, they have remained relatively inefficient compared to conventional centrifugal pumps. To find an optimized design of vortex pumps, this paper provides a systematic analysis on experimental studies that investigated how variations in geometric parameters influence vortex pump characteristics, in particular the pump head, the pressure coefficient and the efficiency for best point operation. To this end, an extensive literature search was conducted, and eighteen articles with 53 primary investigations were identified and meta-integrated. This showed that it is not yet clarified how vortex pumps operate. Two different assumptions of the underlying operating principle of a vortex pump lead to diverging design principles. From the results of this meta-analysis, we deduce recommendations for a more efficient design of a vortex pump and emphasize further aspects on the underlying operating principle of a vortex pump.

Design and experimental study of a solar system for heating water ...

African Journals Online (AJOL)

This work presents a design and an experimental study of a linear Fresnel reflector solar with trapezoidal cavity. This prototype is used for heating the tap water. The reflector was designed, constructed and tested in mechanical engineering department, University of Blida 1, Algeria. Various combinations of reflecting mirrors ...

High temperature pressure water's blowdown into water. Experimental results

International Nuclear Information System (INIS)

Ishida, Toshihisa; Kusunoki, Tsuyoshi; Kasahara, Yoshiyuki; Iida, Hiromasa

1994-01-01

The purpose of the present experimental study is to clarify the phenomena in blowdown of high temperature and pressure water in pressure vessel into the containment water for evaluation of design of an advanced marine reactor(MRX). The water blown into the containment water flushed and formed steam jet plume. The steam jet condensed in the water, but some stream penetrated to gas phase of containment and contributed to increase of containment pressure. (author)

Experimental design and estimation of growth rate distributions in size-structured shrimp populations

International Nuclear Information System (INIS)

Banks, H T; Davis, Jimena L; Ernstberger, Stacey L; Hu, Shuhua; Artimovich, Elena; Dhar, Arun K

2009-01-01

We discuss inverse problem results for problems involving the estimation of probability distributions using aggregate data for growth in populations. We begin with a mathematical model describing variability in the early growth process of size-structured shrimp populations and discuss a computational methodology for the design of experiments to validate the model and estimate the growth-rate distributions in shrimp populations. Parameter-estimation findings using experimental data from experiments so designed for shrimp populations cultivated at Advanced BioNutrition Corporation are presented, illustrating the usefulness of mathematical and statistical modeling in understanding the uncertainty in the growth dynamics of such populations

TIBER: Tokamak Ignition/Burn Experimental Research. Final design report

International Nuclear Information System (INIS)

Henning, C.D.; Logan, B.G.; Barr, W.L.

1985-01-01

The Tokamak Ignition/Burn Experimental Research (TIBER) device is the smallest superconductivity tokamak designed to date. In the design plasma shaping is used to achieve a high plasma beta. Neutron shielding is minimized to achieve the desired small device size, but the superconducting magnets must be shielded sufficiently to reduce the neutron heat load and the gamma-ray dose to various components of the device. Specifications of the plasma-shaping coil, the shielding, coaling, requirements, and heating modes are given. 61 refs., 92 figs., 30 tabs

Experimental design for reflection measurements of highly reactive liquid or solid substances with application to liquid sodium

International Nuclear Information System (INIS)

Chan, S.H.; Gossler, A.A.

1980-01-01

This technical report describes the experimental part of a program on thermal radiation properties of reactor materials. A versatile goniometer system with associated electronic components and mechanical instruments has been assembled. It is designed to measure spectral, specular reflectances of highly reactive liquid or solid substances over a spectral range of 0.3 μ to 9 μ and incidence angles of 12 0 to 30 0 off the normal direction. The capability of measuring reflectances of liquid substances clearly distinguishes this experimental design from conventional systems which are applicable only to solid substances. This design has been used to measure the spectral, specular reflectance of liquid sodium and preliminary results obtained are compared with those of solid sodium measured by other investigators

Comparison the Results of Numerical Simulation And Experimental Results for Amirkabir Plasma Focus Facility

Science.gov (United States)

Goudarzi, Shervin; Amrollahi, R.; Niknam Sharak, M.

2014-06-01

In this paper the results of the numerical simulation for Amirkabir Mather-type Plasma Focus Facility (16 kV, 36μF and 115 nH) in several experiments with Argon as working gas at different working conditions (different discharge voltages and gas pressures) have been presented and compared with the experimental results. Two different models have been used for simulation: five-phase model of Lee and lumped parameter model of Gonzalez. It is seen that the results (optimum pressures and current signals) of the Lee model at different working conditions show better agreement than lumped parameter model with experimental values.

Comparison the results of numerical simulation and experimental results for Amirkabir plasma focus facility

International Nuclear Information System (INIS)

Goudarzi, Shervin; Amrollahi, R; Sharak, M Niknam

2014-01-01

In this paper the results of the numerical simulation for Amirkabir Mather-type Plasma Focus Facility (16 kV, 36μF and 115 nH) in several experiments with Argon as working gas at different working conditions (different discharge voltages and gas pressures) have been presented and compared with the experimental results. Two different models have been used for simulation: five-phase model of Lee and lumped parameter model of Gonzalez. It is seen that the results (optimum pressures and current signals) of the Lee model at different working conditions show better agreement than lumped parameter model with experimental values.

Experimental Device for Learning of Logical Circuit Design using Integrated Circuits

OpenAIRE

石橋, 孝昭

2012-01-01

This paper presents an experimental device for learning of logical circuit design using integrated circuits and breadboards. The experimental device can be made at a low cost and can be used for many subjects such as logical circuits, computer engineering, basic electricity, electrical circuits and electronic circuits. The proposed device is effective to learn the logical circuits than the usual lecture.

Design study of blanket structure for tokamak experimental fusion reactor

International Nuclear Information System (INIS)

1979-11-01

Design study of the blanket structure for JAERI Experimental Fusion Reactor (JXFR) has been carried out. Studied here were fabrication and testing of the blanket structure (blanket cells, blanket rings, piping and blanket modules), assembly and disassembly of the blanket module, and monitering and testing technique. Problems in design and fabrication of the blanket structure could be revealed. Research and development problems for the future were also disclosed. (author)

Investigation of the effect of rollbond evaporator design on the performance of direct expansion heat pump experimentally

International Nuclear Information System (INIS)

Cerit, Emine; Erbay, L. Berrin

2013-01-01

Highlights: • Effect of rollbond evaporator design to performance of the DX-SAHP is investigated. • Experiments performed on three identical DX-SAHP systems except evaporator design. • Evaporators’ material is aluminum and R134a is the working fluid. • Empirical correlation derived for system COP in terms of radiation and temperature. • The correlation provides the average deviation of 9% with the experimental data. - Abstract: In this study, the rollbond evaporator design which gives maximum coefficient of performance for the direct expansion solar assisted heat pump (DX-SAHP) water heater is investigated experimentally on the three separate heat pump systems due to the lack of studies on the effect of collector-evaporator design to the system performance. Three DX-SAHP systems are identical except collector-evaporator design. Aluminum is preferred for the evaporator material and R134a as the working fluid. Maximum COP value was obtained as 3.30 for System-1 while COP values for System-2 and System-3 were 3.14 and 2.42 respectively at the same conditions. An empirical correlation which gives the COP value of the System-1, which provides highest COP, with respect to the solar radiation and outdoor temperature of the system has been found using the experimental results obtained during the study. The correlation was found to be in good agreement with the average deviation of 9% with the experimental data

An experimental school prototype: Integrating 3rs (reduce, reuse & recycle concept into architectural design

Directory of Open Access Journals (Sweden)

Kong Seng Yeap

2012-06-01

Full Text Available The authors conducted a design project to examine the use of school as an ecological learning hub for children. Specifically, this study explores the ecological innovations that transform physical environment into three-dimensional textbooks for environmental education. A series of design workshops were carried out to gain interdisciplinary input for ecological school design. The findings suggest to integrate the concept of 3Rs (Reduce, Reuse & Recycle into the physical environment. As a result, an experimental school prototype is developed. It represents a series of recommendations that are rendered by novel ideas through the amalgamation of architecture, ecology and education. These findings promote the development of sustainable and interactive learning spaces through cross-disciplinary investigations in school architecture. Designers and practitioners interested in educational facilities design would find this article useful.

Materials by design: An experimental and computational investigation on the microanatomy arrangement of porous metallic glasses

International Nuclear Information System (INIS)

Sarac, Baran; Klusemann, Benjamin; Xiao, Tao; Bargmann, Swantje

2014-01-01

The correlation of a material’s structure with its properties is one of the important unresolved issues in materials science research. This paper discusses a novel experimental and computational approach by which the influence of the pores on the mechanical properties of bulk metallic glasses (BMGs) can be systematically and quantitatively analyzed. The experimental stage involves the fabrication of a template whose pore configurations are pre-determined by computer-aided design tools, and replication of the designed patterns with BMGs. Quasi-static mechanical characterization of these complex microstructures is conducted under uniaxial tension and in-plane compression. For the numerical simulations, a non-local gradient-enhanced continuum mechanical model is established, using thermodynamic principles and periodic boundary conditions. The combination of the experimental and numerical results has identified the importance of the pore configuration, overall porosity and diameter to the spacing ratio of the pores to attain optimized material properties

Design considerations for ITER [International Thermonuclear Experimental Reactor] magnet systems

International Nuclear Information System (INIS)

Henning, C.D.; Miller, J.R.

1988-01-01

The International Thermonuclear Experimental Reactor (ITER) is now completing a definition phase as a beginning of a three-year design effort. Preliminary parameters for the superconducting magnet system have been established to guide further and more detailed design work. Radiation tolerance of the superconductors and insulators has been of prime importance, since it sets requirements for the neutron-shield dimension and sensitively influences reactor size. The major levels of mechanical stress in the structure appear in the cases of the inboard legs of the toroidal-field (TF) coils. The cases of the poloidal-field (PF) coils must be made thin or segmented to minimize eddy current heating during inductive plasma operation. As a result, the winding packs of both the TF and PF coils includes significant fractions of steel. The TF winding pack provides support against in-plane separating loads but offers little support against out-of-plane loads, unless shear-bonding of the conductors can be maintained. The removal of heat due to nuclear and ac loads has not been a fundamental limit to design, but certainly has non-negligible economic consequences. We present here preliminary ITER magnetic systems design parameters taken from trade studies, designs, and analyses performed by the Home Teams of the four ITER participants, by the ITER Magnet Design Unit in Garching, and by other participants at workshops organized by the Magnet Design Unit. The work presented here reflects the efforts of many, but the responsibility for the opinions expressed is the authors'. 4 refs., 3 figs., 4 tabs

PDX experimental results in FY82

International Nuclear Information System (INIS)

Kaye, S.M.; Bell, M.; Bol, K.

1983-08-01

This report presents a detailed summary of the major experimental results of PDX in FY82 and represents the efforts of the entire PDX group. Topics covered include β-scaling and fishbone studies, fluctuations, disruptions, impurities and impurity transport, power handling, limiter conditioning, edge studies, plasma fueling, counter-injection, and diagnostic development. A less detailed version will appear as the FY82 PDX contribution to the PPPL Annual Report

Test of the core design methods for the THTR 300 with experimental results from the critical facility KAHTER

Energy Technology Data Exchange (ETDEWEB)

Hofmann, K.; Huebner, A.; Brandes, S.; Krings, F.

1974-10-15

At the Kernforschungsanlage Juelich, core physics experiments with core 1 and core 2 of the critical facility for high temperature reactors KAHTER were carried out in 1973. Core 2 corresponds to the THTR initial core in its moderation ratio S = 7500. Selected experimental results on the critical mass, on control rod worths, and reaction rate distributions were used for testing the most important procedures for the THTR core physics design. The zero-dimensional spectrum program MUPO with its cross section library and the and neutron flux calculations in two-dimensional diffusion approximation by CRAM are of central importance. It proved to be important to introduce modifications specific to the KAHTER plant into the standard models. Thus the void effect (void above the pebble bed) was investigated with DOT-2 by transport theory and a correction was introduced for the critical masses calculated by diffusion theory. Another feature already contained in the standard procedure, the increase of the diffusion constants for the hollow spaces between the spheres, results in a correction of 3.8% < delta-k for KAHTER, whereas in the THTR 300 it only amounts to several tenths % delta-k. Critical masses are predicted with accuracies of < 1.5 % or with regard to reactivity < 0.65 % delta-k. The calculated values for the radial neutron flux distributions deviate from the measured values in the core area by approximately lo %. In the case of the axial profiles, deviations are observed at the pebble bed surface which can be explained by the upper void, which cannot be satisfactorily represented by the diffusion theory. Control rod worths are predicted quite well, i.e., to within +/- 5%. An exception is the bank of 4 reflector rods, where the applied model of the "grey curtain" is not accurate because of the large distances between rods. The calculated control rod worths for that case were found to be too low, which does, however, not result in a safety problem.

Experimental results on evaporation waves

Science.gov (United States)

Grana Otero, Jose; Parra Fabian, Ignacio

2010-11-01

A liquid contained in a vertical glass tube is suddenly depressurized from a high initial pressure down to one for which the stable state is vapour, so vaporization sets off at the free surface. For large enough evaporation rates, the planar vapour-liquid interface is Darrieus-Landau unstable [1], leading to the interface surface rippling close to the instability threshold. Further increasing the initial to final pressure ratio brings about evaporation waves [2,3], in which a highly corrugated front propagates downwards into the liquid. A new experimental method is presented as well as some experimental results obtained by tracking the evolution of the front with a high speed camera. In addition, a number of new phenomena related to the dynamics of bubbles growth at the walls has been uncovered. In particular, a new mode of propagation of the evaporation front is found. In this mode the front originates from below the interface, so the propagation is upwards against gravity with a curved but smooth front.[4pt] [1] F. J. Higuera, Phys. Fluids, V. 30, 679 (1987).[0pt] [2] J.E.Shepherd and B.Sturtevant, J.Fluid Mech., V.121,379 (1982).[0pt] [3] P.Reinke and G.Yadigaroglu, Int.J.Multiph. Flow, V.27,1487 (2001).

Transforming the Organic Chemistry Lab Experience: Design, Implementation, and Evaluation of Reformed Experimental Activities--REActivities

Science.gov (United States)

Collison, Christina G.; Kim, Thomas; Cody, Jeremy; Anderson, Jason; Edelbach, Brian; Marmor, William; Kipsang, Rodgers; Ayotte, Charles; Saviola, Daniel; Niziol, Justin

2018-01-01

Reformed experimental activities (REActivities) are an innovative approach to the delivery of the traditional material in an undergraduate organic chemistry laboratory. A description of the design and implementation of REActivities at both a four- and two-year institution is discussed. The results obtained using a reformed teaching observational…

Calculating buoy response for a wave energy converter—A comparison of two computational methods and experimental results

Directory of Open Access Journals (Sweden)

Linnea Sjökvist

2017-05-01

Full Text Available When designing a wave power plant, reliable and fast simulation tools are required. Computational fluid dynamics (CFD software provides high accuracy but with a very high computational cost, and in operational, moderate sea states, linear potential flow theories may be sufficient to model the hydrodynamics. In this paper, a model is built in COMSOL Multiphysics to solve for the hydrodynamic parameters of a point-absorbing wave energy device. The results are compared with a linear model where the hydrodynamical parameters are computed using WAMIT, and to experimental results from the Lysekil research site. The agreement with experimental data is good for both numerical models.

Experimental results of a direct air-cooled ammonia–lithium nitrate absorption refrigeration system

International Nuclear Information System (INIS)

Llamas-Guillén, S.U.; Cuevas, R.; Best, R.; Gómez, V.H.

2014-01-01

Absorption thermal cooling systems driven by renewable energy are a viable option in order to reduce fossil fuel consumption and the associated emissions. This work shows the results of an air cooled absorption cooling prototype working with an ammonia–lithium nitrate mixture at high ambient temperatures. An absorption refrigeration system was designed and built. The prototype is a one stage ammonia–lithium nitrate air cooled chiller. The experimental system was instrumented to evaluate each component. This paper shows the operation conditions in the experimental unit as well as some of the heat loads encountered at different operating conditions. The system was operated successfully at ambient temperatures in the range of 25–35 °C. A series of test showed that even at ambient temperatures it can be operated at evaporator temperatures below 10 °C producing chilled water for air conditioning applications such as radiative cooling panels. The system proved to stabilize very quickly and no risk of crystallization was encountered so the first results are promising in order to continue with the development of a more advanced prototype. - Highlights: •Experimental results of a direct air-cooled ammonia–lithium nitrate system. •The prototype is a one stage ammonia–lithium nitrate air cooled chiller. •The absorption system was operated successfully at ambient temperatures. •Cooling loads of 4.5 kW were reached in the chilled water side

The Impact of Diagnostic Code Misclassification on Optimizing the Experimental Design of Genetic Association Studies

Directory of Open Access Journals (Sweden)

Steven J. Schrodi

2017-01-01

Full Text Available Diagnostic codes within electronic health record systems can vary widely in accuracy. It has been noted that the number of instances of a particular diagnostic code monotonically increases with the accuracy of disease phenotype classification. As a growing number of health system databases become linked with genomic data, it is critically important to understand the effect of this misclassification on the power of genetic association studies. Here, I investigate the impact of this diagnostic code misclassification on the power of genetic association studies with the aim to better inform experimental designs using health informatics data. The trade-off between (i reduced misclassification rates from utilizing additional instances of a diagnostic code per individual and (ii the resulting smaller sample size is explored, and general rules are presented to improve experimental designs.

Experimental analysis of the performance of an air-water heat pump designed for R22 working with propane

International Nuclear Information System (INIS)

Mura, P.G.; Carlini, U.; Innamorati, R.

2001-01-01

After describing the technical characteristics of a heat pump designed for R22, the changes necessary to fit the use of propane and the experimental set-up, in this article the research program on propane as refrigerant is presented, together with the experimental results of the chiller performance with R22 and R290 in cooling mode [it

Experimental concept and design of DarkLight, a search for a heavy photon

International Nuclear Information System (INIS)

Cowan, Ray F.

2013-01-01

This talk gives an overview of the DarkLight experimental concept: a search for a heavy photon A′ in the 10-90 MeV/c 2 mass range. After briefly describing the theoretical motivation, the talk focuses on the experimental concept and design. Topics include operation using a half-megawatt, 100 MeV electron beam at the Jefferson Lab FEL, detector design and performance, and expected backgrounds estimated from beam tests and Monte Carlo simulations

Master-Slave synchronization of robot manipulators: experimental results

NARCIS (Netherlands)

Bondhus, A.K.; Pettersen, K.Y.; Nijmeijer, H.

2005-01-01

This paper presents experimental results for master-slave synchronization of two robot manipulators using a recently developed observer-controller scheme. The paper aims to investigate the value and the limitations of the theory. In particular, the theoretical result of uniform ultimate boundedness

Design and experimental study on desulphurization process of ship exhaust

Science.gov (United States)

Han, Mingyang; Hao, Shan; Zhou, Junbo; Gao, Liping

2018-02-01

This desulfurization process involves removing sulfur oxides with seawater or alkaline aqueous solutions and then treating the effluent by aeration and pH adjustment before discharging it into the ocean. In the desulfurization system, the spray tower is the key equipment and the venturi tubes are the pretreatment device. The two stages of plates are designed to fully absorb sulfur oxides in exhaust gases. The spiral nozzles atomize and evenly spray the desulfurizers into the tower. This study experimentally investigated the effectiveness of this desulfurization process and the factors influencing it under laboratory conditions, with a diesel engine exhaust used to represent ship exhaust. The experimental results show that this process can effectively absorb the SO2 in the exhaust. When the exhaust flow rate was 25 m3/h and the desulfurizer flow rate was 4 L/min, the sulfur removal efficiency (SRE) reached 99.7%. The flow rate, alkalinity, and temperature of seawater were found to have significant effects on the SRE. Adjusting seawater flow rate (SWR) and alkalinity within certain ranges can substantially improve the SRE.

Sliding spool design for reducing the actuation forces in direct operated proportional directional valves: Experimental validation

International Nuclear Information System (INIS)

Amirante, Riccardo; Distaso, Elia; Tamburrano, Paolo

2016-01-01

Highlights: • An innovative procedure to design a commercial proportional directional valve is shown. • Experimental tests are performed to demonstrate the flow force reduction. • The design is improved by means of a previously made optimization procedure. • Great reduction in the flow forces without reducing the flow rate is demonstrated. - Abstract: This paper presents the experimental validation of a new methodology for the design of the spool surfaces of four way three position direct operated proportional directional valves. The proposed methodology is based on the re-design of both the compensation profile (the central conical surface of the spool) and the lateral surfaces of the spool, in order to reduce the flow forces acting on the spool and hence the actuation forces. The aim of this work is to extend the application range of these valves to higher values of pressure and flow rate, thus avoiding the employment of more expensive two stage configurations in the case of high-pressure conditions and/or flow rate. The paper first presents a theoretical approach and a general strategy for the sliding spool design to be applied to any four way three position direct operated proportional directional valve. Then, the proposed approach is experimentally validated on a commercially available valve using a hydraulic circuit capable of measuring the flow rate as well as the actuation force over the entire spool stroke. The experimental results, performed using both the electronic driver provided by the manufacturer and a manual actuation system, show that the novel spool surface requires remarkably lower actuation forces compared to the commercial configuration, while maintaining the same flow rate trend as a function of the spool position.

Containment Evaluation under Severe Accidents (CESA): synthesis of the predictive calculations and analysis of the first experimental results obtained on the Civaux mock-up

International Nuclear Information System (INIS)

Granger, L.; Rieg, C.Y.; Touret, J.P.; Fleury, F.; Nahas, G.; Danisch, R.; Brusa, L.; Millard, A.; Laborderie, C.; Ulm, F.; Contri, P.; Schimmelpfennig, K.; Barre, F.; Firnhaber, M.; Gauvain, J; Coulon, N.; Dutton, L.M.C.; Tuson, A.

2001-01-01

In 1996, EDF decided to build a containment model at the scale 1:3, the MAEVA mock-up, in order to check and study the behaviour of a pre-stressed concrete containment vessel without a liner in terms of mechanical strength and leaktightness, for loadings corresponding to its design and beyond design conditions. In parallel with the construction and testing of the mock-up, a cost-shared R and D action supported by the European Union, the CESA project, is dealing with quantification of leak rates through concrete cracks and porosity, predictive calculations of the behaviour of the mock-up and analysis of the experimental results. In this paper, we propose a synthesis of the main theoretical and experimental results, obtained after 2.5 years. It should however be noted that, due to some unexpected delays in the experimental programme, quite natural with such a huge and unique experimental set-up, only the design-basis accident sequences, already performed, have been reported in this paper. The first results are nevertheless very interesting, both from a scientific and nuclear utility point of view

A design and experimental verification methodology for an energy harvester skin structure

Science.gov (United States)

Lee, Soobum; Youn, Byeng D.

2011-05-01

This paper presents a design and experimental verification methodology for energy harvesting (EH) skin, which opens up a practical and compact piezoelectric energy harvesting concept. In the past, EH research has primarily focused on the design improvement of a cantilever-type EH device. However, such EH devices require additional space for proof mass and fixture and sometimes result in significant energy loss as the clamping condition becomes loose. Unlike the cantilever-type device, the proposed design is simply implemented by laminating a thin piezoelectric patch onto a vibrating structure. The design methodology proposed, which determines a highly efficient piezoelectric material distribution, is composed of two tasks: (i) topology optimization and (ii) shape optimization of the EH material. An outdoor condensing unit is chosen as a case study among many engineered systems with harmonic vibrating configuration. The proposed design methodology determined an optimal PZT material configuration on the outdoor unit skin structure. The designed EH skin was carefully prototyped to demonstrate that it can generate power up to 3.7 mW, which is sustainable for operating wireless sensor units for structural health monitoring and/or building automation.

A design and experimental verification methodology for an energy harvester skin structure

International Nuclear Information System (INIS)

Lee, Soobum; Youn, Byeng D

2011-01-01

This paper presents a design and experimental verification methodology for energy harvesting (EH) skin, which opens up a practical and compact piezoelectric energy harvesting concept. In the past, EH research has primarily focused on the design improvement of a cantilever-type EH device. However, such EH devices require additional space for proof mass and fixture and sometimes result in significant energy loss as the clamping condition becomes loose. Unlike the cantilever-type device, the proposed design is simply implemented by laminating a thin piezoelectric patch onto a vibrating structure. The design methodology proposed, which determines a highly efficient piezoelectric material distribution, is composed of two tasks: (i) topology optimization and (ii) shape optimization of the EH material. An outdoor condensing unit is chosen as a case study among many engineered systems with harmonic vibrating configuration. The proposed design methodology determined an optimal PZT material configuration on the outdoor unit skin structure. The designed EH skin was carefully prototyped to demonstrate that it can generate power up to 3.7 mW, which is sustainable for operating wireless sensor units for structural health monitoring and/or building automation. (technical note)

Design and Implementation of an Experimental Cataloging Advisor--Mapper.

Science.gov (United States)

Ercegovac, Zorana; Borko, Harold

1992-01-01

Describes the design of an experimental computer-aided cataloging advisor, Mapper, that was developed to help novice users with the descriptive cataloging of single-sheet maps from U.S. publishers. The human-computer interface is considered, the use of HyperCard is discussed, the knowledge base is explained, and assistance screens are described.…

Experimental results for an experimental condensation heat exchanger with a spiral minichanel tube. Comparison to numerical imulations

Directory of Open Access Journals (Sweden)

Hrubý J.

2013-04-01

Full Text Available The paper describes new results for an experimental heat exchanger equipped with a single corrugated capillary tube, basic information about the measurements and the experimental setup. Some of the results were compared with numerical simulations.

Removal of thorium(IV) from aqueous solution by biosorption onto modified powdered waste sludge. Experimental design approach

International Nuclear Information System (INIS)

Yunus Pamukoglu, M.; Mustafa Senyurt; Bulent Kirkan

2017-01-01

The biosorption of radioactive Th(IV) ions in the aqueous solutions onto the modified powdered waste sludge (MPWS) has been examined. In this context, the parameters affecting biosorption of Th(IV) from aqueous solutions has been examined by using MPWS biosorbent in Box Behnken statistical experimental design. The structure of MPWS biosorbent was characterized by using SEM and BET techniques. According to the experimental design results, MPWS and Th(IV) concentrations should be kept high to achieve the maximum efficiency in Th(IV) biosorption. On the other hand, MPWS, which is also used as a biosorbent, is an economical, effective and natural biosorbent. (author)

Experimental study of elementary collection efficiency of aerosols by spray: Design of the experimental device

Energy Technology Data Exchange (ETDEWEB)

Ducret, D.; Vendel, J.; Garrec. S.L.

1995-02-01

The safety of a nuclear power plant containment building, in which pressure and temperature could increase because of a overheating reactor accident, can be achieved by spraying water drops. The spray reduces the pressure and the temperature levels by condensation of steam on cold water drops. The more stringent thermodynamic conditions are a pressure of 5.10{sup 5} Pa (due to steam emission) and a temperature of 413 K. Moreover its energy dissipation function, the spray leads to the washout of fission product particles emitted in the reactor building atmosphere. The present study includes a large program devoted to the evaluation of realistic washout rates. The aim of this work is to develop experiments in order to determine the collection efficiency of aerosols by a single drop. To do this, the experimental device has to be designed with fundamental criteria:-Thermodynamic conditions have to be representative of post-accident atmosphere. Thermodynamic equilibrium has to be attained between the water drops and the gaseous phase. Thermophoretic, diffusiophoretic and mechanical effects have to be studied independently. Operating conditions have to be homogenous and constant during each experiment. This paper presents the design of the experimental device. In practice, the consequences on the design of each of the criteria given previously and the necessity of being representative of the real conditions will be described.

Beam dynamics studies at DAΦNE: from ideas to experimental results

Science.gov (United States)

Zobov, M.; DAΦNE Team

2017-12-01

DAΦNE is the electron-positron collider operating at the energy of Φ-resonance, 1 GeV in the center of mass. The presently achieved luminosity is by about two orders of magnitude higher than that obtained at other colliders ever operated at this energy. Careful beam dynamic studies such as the vacuum chamber design with low beam coupling impedance, suppression of different kinds of beam instabilities, investigation of beam-beam interaction, optimization of the beam nonlinear motion have been the key ingredients that have helped to reach this impressive result. Many novel ideas in accelerator physics have been proposed and/or tested experimentally at DAΦNE for the first time. In this paper we discuss the advanced accelerator physics studies performed at DAΦNE.

Experimental validation of thermal design of top shield for a pool type SFR

International Nuclear Information System (INIS)

Aithal, Sriramachandra; Babu, V. Rajan; Balasubramaniyan, V.; Velusamy, K.; Chellapandi, P.

2016-01-01

Highlights: • Overall thermal design of top shield in a SFR is experimentally verified. • Air jet cooling is effective in ensuring the temperatures limits for top shield. • Convection patterns in narrow annulus are in line with published CFD results. • Wire mesh insulation ensures gradual thermal gradient at top portion of main vessel. • Under loss of cooling scenario, sufficient time is available for corrective action. - Abstract: An Integrated Top Shield Test Facility towards validation of thermal design of top shield for a pool type SFR has been conceived, constructed & commissioned. Detailed experiments were performed in this experimental facility having full-scale features. Steady state temperature distribution within the facility is measured for various heater plate temperatures in addition to simulating different operating states of the reactor. Following are the important observations (i) jet cooling system is effective in regulating the roof slab bottom plate temperature and thermal gradient across roof slab simulating normal operation of reactor, (ii) wire mesh insulation provided in roof slab-main vessel annulus is effective in obtaining gradual thermal gradient along main vessel top portion and inhibiting the setting up of cellular convection within annulus and (iii) cellular convection with four distinct convective cells sets in the annular gap between roof slab and small rotatable plug measuring ∼ϕ4 m in diameter & gap width varying from 16 mm to 30 mm. Repeatability of results is also ensured during all the above tests. The results presented in this paper is expected to provide reference data for validation of thermal hydraulic models in addition to serving as design validation of jet cooling system for pool type SFR.

Planned experimental studies on natural-circulation and stability performance of boiling water reactors in four experimental facilities and first results (NACUSP)

Energy Technology Data Exchange (ETDEWEB)

Kruijf, W.J.M. de E-mail: kruijf@iri.tudelft.nl; Ketelaar, K.C.J.; Avakian, G.; Gubernatis, P.; Caruge, D.; Manera, A.; Hagen, T.H.J.J. van der; Yadigaroglu, G.; Dominicus, G.; Rohde, U.; Prasser, H.-M.; Castrillo, F.; Huggenberger, M.; Hennig, D.; Munoz-Cobo, J.L.; Aguirre, C

2003-04-01

Within the 5th Euratom framework programme the NACUSP project focuses on natural-circulation and stability characteristics of Boiling Water Reactors (BWRs). This paper gives an overview of the research to be performed. Moreover, it shows the first results obtained by one of the four experimental facilities involved. Stability boundaries are given for the low-power low-pressure operating range, measured in the CIRCUS facility. The experiments are meant to serve as a future validation database for thermohydraulic system codes to be applied for the design and operation of BWRs.

Planned experimental studies on natural-circulation and stability performance of boiling water reactors in four experimental facilities and first results (NACUSP)

International Nuclear Information System (INIS)

Kruijf, W.J.M. de; Ketelaar, K.C.J.; Avakian, G.; Gubernatis, P.; Caruge, D.; Manera, A.; Hagen, T.H.J.J. van der; Yadigaroglu, G.; Dominicus, G.; Rohde, U.; Prasser, H.-M.; Castrillo, F.; Huggenberger, M.; Hennig, D.; Munoz-Cobo, J.L.; Aguirre, C.

2003-01-01

Within the 5th Euratom framework programme the NACUSP project focuses on natural-circulation and stability characteristics of Boiling Water Reactors (BWRs). This paper gives an overview of the research to be performed. Moreover, it shows the first results obtained by one of the four experimental facilities involved. Stability boundaries are given for the low-power low-pressure operating range, measured in the CIRCUS facility. The experiments are meant to serve as a future validation database for thermohydraulic system codes to be applied for the design and operation of BWRs

Biomass downdraft gasifier with internal cyclonic combustion chamber: design, construction, and experimental results.

Science.gov (United States)

Patil, Krushna; Bhoi, Prakash; Huhnke, Raymond; Bellmer, Danielle

2011-05-01

An exploratory downdraft gasifier design with unique biomass pyrolysis and tar cracking mechanism is evolved at Oklahoma State University. This design has an internal separate combustion section where turbulent, swirling high-temperature combustion flows are generated. A series of research trials were conducted using wood shavings as the gasifier feedstock. Maximum tar cracking temperatures were above 1100°C. Average volumetric concentration levels of major combustible components in the product gas were 22% CO and 11% H(2). Hot and cold gas efficiencies were 72% and 66%, respectively. Copyright © 2011 Elsevier Ltd. All rights reserved.

Acting like a physicist: Student approach study to experimental design

Science.gov (United States)

Karelina, Anna; Etkina, Eugenia

2007-12-01

National studies of science education have unanimously concluded that preparing our students for the demands of the 21st century workplace is one of the major goals. This paper describes a study of student activities in introductory college physics labs, which were designed to help students acquire abilities that are valuable in the workplace. In these labs [called Investigative Science Learning Environment (ISLE) labs], students design their own experiments. Our previous studies have shown that students in these labs acquire scientific abilities such as the ability to design an experiment to solve a problem, the ability to collect and analyze data, the ability to evaluate assumptions and uncertainties, and the ability to communicate. These studies mostly concentrated on analyzing students’ writing, evaluated by specially designed scientific ability rubrics. Recently, we started to study whether the ISLE labs make students not only write like scientists but also engage in discussions and act like scientists while doing the labs. For example, do students plan an experiment, validate assumptions, evaluate results, and revise the experiment if necessary? A brief report of some of our findings that came from monitoring students’ activity during ISLE and nondesign labs was presented in the Physics Education Research Conference Proceedings. We found differences in student behavior and discussions that indicated that ISLE labs do in fact encourage a scientistlike approach to experimental design and promote high-quality discussions. This paper presents a full description of the study.

Acting like a physicist: Student approach study to experimental design

Directory of Open Access Journals (Sweden)

Anna Karelina

2007-10-01

Full Text Available National studies of science education have unanimously concluded that preparing our students for the demands of the 21st century workplace is one of the major goals. This paper describes a study of student activities in introductory college physics labs, which were designed to help students acquire abilities that are valuable in the workplace. In these labs [called Investigative Science Learning Environment (ISLE labs], students design their own experiments. Our previous studies have shown that students in these labs acquire scientific abilities such as the ability to design an experiment to solve a problem, the ability to collect and analyze data, the ability to evaluate assumptions and uncertainties, and the ability to communicate. These studies mostly concentrated on analyzing students’ writing, evaluated by specially designed scientific ability rubrics. Recently, we started to study whether the ISLE labs make students not only write like scientists but also engage in discussions and act like scientists while doing the labs. For example, do students plan an experiment, validate assumptions, evaluate results, and revise the experiment if necessary? A brief report of some of our findings that came from monitoring students’ activity during ISLE and nondesign labs was presented in the Physics Education Research Conference Proceedings. We found differences in student behavior and discussions that indicated that ISLE labs do in fact encourage a scientistlike approach to experimental design and promote high-quality discussions. This paper presents a full description of the study.

Fast Synthesis of Gibbsite Nanoplates and Process Optimization using Box-Behnken Experimental Design

Energy Technology Data Exchange (ETDEWEB)

Zhang, Xin; Zhang, Xianwen; Graham, Trenton R.; Pearce, Carolyn I.; Mehdi, Beata L.; N' Diaye, Alpha T.; Kerisit, Sebastien N.; Browning, Nigel D.; Clark, Sue B.; Rosso, Kevin M.

2017-10-26

Developing the ability to synthesize compositionally and morphologically well-defined gibbsite particles at the nanoscale with high yield is an ongoing need that has not yet achieved the level of rational design. Here we report optimization of a clean inorganic synthesis route based on statistical experimental design examining the influence of Al(OH)3 gel precursor concentration, pH, and aging time at temperature. At 80 oC, the optimum synthesis conditions of gel concentration at 0.5 M, pH at 9.2, and time at 72 h maximized the reaction yield up to ~87%. The resulting gibbsite product is composed of highly uniform euhedral hexagonal nanoplates within a basal plane diameter range of 200-400 nm. The independent roles of key system variables in the growth mechanism are considered. On the basis of these optimized experimental conditions, the synthesis procedure, which is both cost-effective and environmentally friendly, has the potential for mass production scale-up of high quality gibbsite material for various fundamental research and industrial applications.

Statistics in experimental design, preprocessing, and analysis of proteomics data.

Science.gov (United States)

Jung, Klaus

2011-01-01

High-throughput experiments in proteomics, such as 2-dimensional gel electrophoresis (2-DE) and mass spectrometry (MS), yield usually high-dimensional data sets of expression values for hundreds or thousands of proteins which are, however, observed on only a relatively small number of biological samples. Statistical methods for the planning and analysis of experiments are important to avoid false conclusions and to receive tenable results. In this chapter, the most frequent experimental designs for proteomics experiments are illustrated. In particular, focus is put on studies for the detection of differentially regulated proteins. Furthermore, issues of sample size planning, statistical analysis of expression levels as well as methods for data preprocessing are covered.

Controller design and test results for a four axis HTS coil based Maglev system

International Nuclear Information System (INIS)

Zhou Tong; Xing Huawei

2007-01-01

Controller design and experimental results are reported in this paper for a four axis high temperature superconductivity (HTS) coil based electromagnetic levitation (Maglev) system. The HTS coils are made of Bi2223/Ag multifilamentary tapes. It has been experimentally proved that the designed controller works satisfactorily, although the physical parameters of a HTS coil based electromagnet (HTSEM) vary significantly with the frequency of the input voltage. A performance comparison has also been made between the classical lead-lag compensator and the modern H ∼ loop-shaping controller. It becomes clear that robust control theories are capable of providing a controller with better performances, which is in a good agreement with numerical simulations. Moreover, it implies that the particular parameter variation characteristics can be simply dealt with by the available robust control theories that are naturally existent in a HTSEM

Controller design and test results for a four axis HTS coil based Maglev system

Energy Technology Data Exchange (ETDEWEB)

Zhou Tong [Department of Automation, Tsinghua University, Beijing 100084 (China)]. E-mail: tzhou@mail.tsinghua.edu.cn; Xing Huawei [Department of Automation, Tsinghua University, Beijing 100084 (China)

2007-04-15

Controller design and experimental results are reported in this paper for a four axis high temperature superconductivity (HTS) coil based electromagnetic levitation (Maglev) system. The HTS coils are made of Bi2223/Ag multifilamentary tapes. It has been experimentally proved that the designed controller works satisfactorily, although the physical parameters of a HTS coil based electromagnet (HTSEM) vary significantly with the frequency of the input voltage. A performance comparison has also been made between the classical lead-lag compensator and the modern H{sub {approx}} loop-shaping controller. It becomes clear that robust control theories are capable of providing a controller with better performances, which is in a good agreement with numerical simulations. Moreover, it implies that the particular parameter variation characteristics can be simply dealt with by the available robust control theories that are naturally existent in a HTSEM.

Development of A Super High Speed Permanent Magnet Synchronous Motor (PMSM Controller and Analysis of The Experimental Results

Directory of Open Access Journals (Sweden)

Limei Zhao

2005-02-01

Full Text Available This paper presents the design and implementation of a DSP-based controller for a super high-speed (>80,000 rpm permanent magnet synchronous motor (PMSM. The PMSM is a key component of the centrifugal compressor drive of a reverse Brayton cryocooler that is currently under development for NASA and Florida Solar Energy Center. The design of the PMSM open-loop control is presented. Experimental results with open-loop control schemes are presented. System optimization and analysis are also illustrated. They verify the effectiveness of the controller design and the optimization scheme.

Sampling flies or sampling flaws? Experimental design and inference strength in forensic entomology.

Science.gov (United States)

Michaud, J-P; Schoenly, Kenneth G; Moreau, G

2012-01-01

Forensic entomology is an inferential science because postmortem interval estimates are based on the extrapolation of results obtained in field or laboratory settings. Although enormous gains in scientific understanding and methodological practice have been made in forensic entomology over the last few decades, a majority of the field studies we reviewed do not meet the standards for inference, which are 1) adequate replication, 2) independence of experimental units, and 3) experimental conditions that capture a representative range of natural variability. Using a mock case-study approach, we identify design flaws in field and lab experiments and suggest methodological solutions for increasing inference strength that can inform future casework. Suggestions for improving data reporting in future field studies are also proposed.

Experimental design of natural and accellerated bone and wood ageing

DEFF Research Database (Denmark)

Facorellis, Y.; Pournou, A.; Richter, Jane

2015-01-01

This paper presents the experimental design for natural and accelerated ageing of bone and wood samples found in museum conditions that was conceived as part of the INVENVORG (Thales Research Funding Program – NRSF) investigating the effects of the environmental factors on natural organic materials....

Optimization of fast disintegration tablets using pullulan as diluent by central composite experimental design

OpenAIRE

Patel, Dipil; Chauhan, Musharraf; Patel, Ravi; Patel, Jayvadan

2012-01-01

The objective of this work was to apply central composite experimental design to investigate main and interaction effect of formulation parameters in optimizing novel fast disintegration tablets formulation using pullulan as diluents. Face centered central composite experimental design was employed to optimize fast disintegration tablet formulation. The variables studied were concentration of diluents (pullulan, X1), superdisintigrant (sodium starch glycolate, X2), and direct compression aid ...

Development of a Model for Measuring Scientific Processing Skills Based on Brain-Imaging Technology: Focused on the Experimental Design Process

Science.gov (United States)

Lee, Il-Sun; Byeon, Jung-Ho; Kim, Young-shin; Kwon, Yong-Ju

2014-01-01

The purpose of this study was to develop a model for measuring experimental design ability based on functional magnetic resonance imaging (fMRI) during biological inquiry. More specifically, the researchers developed an experimental design task that measures experimental design ability. Using the developed experimental design task, they measured…

Thermodynamic properties of indan: Experimental and computational results

International Nuclear Information System (INIS)

Chirico, Robert D.; Steele, William V.; Kazakov, Andrei F.

2016-01-01

Highlights: • Heat capacities were measured for the temperature range (5 to 445) K. • Vapor pressures were measured for the temperature range (338 to 495) K. • Densities at saturation pressure were measured from T = (323 to 523) K. • Computed and experimentally derived properties for ideal gas entropies are in excellent accord. • Thermodynamic consistency analysis revealed anomalous literature data. - Abstract: Measurements leading to the calculation of thermodynamic properties in the ideal-gas state for indan (Chemical Abstracts registry number [496-11-7], 2,3-dihydro-1H-indene) are reported. Experimental methods were adiabatic heat-capacity calorimetry, differential scanning calorimetry, comparative ebulliometry, and vibrating-tube densitometry. Molar thermodynamic functions (enthalpies, entropies, and Gibbs energies) for the condensed and ideal-gas states were derived from the experimental studies at selected temperatures. Statistical calculations were performed based on molecular geometry optimization and vibrational frequencies calculated at the B3LYP/6-31+G(d, p) level of theory. Computed ideal-gas properties derived with the rigid-rotor harmonic-oscillator approximation are shown to be in excellent accord with ideal-gas entropies derived from thermophysical property measurements of this research, as well as with experimental heat capacities for the ideal-gas state reported in the literature. Literature spectroscopic studies and ab initio calculations report a range of values for the barrier to ring puckering. Results of the present work are consistent with a large barrier that allows use of the rigid-rotor harmonic-oscillator approximation for ideal-gas entropy and heat-capacity calculations, even with the stringent uncertainty requirements imposed by the calorimetric and physical property measurements reported here. All experimental results are compared with property values reported in the literature.

Experimental results and recent developments on the EU 2 MW 170 GHz coaxial cavity gyrotron for ITER

Directory of Open Access Journals (Sweden)

Thumm M. K.

2012-09-01

Full Text Available The European Gyrotron Consortium (EGYC is responsible for developing one set of 170 GHz mm-wave sources, in support of Europe’s contribution to ITER. The original plan of targeting a 2 MW coaxial gyrotron is currently under discussion, in view of essential delays and damages. This paper reports on the latest results and plans with regard to the two 2 MW gyrotron prototypes, the industrial prototype at CRPP’s CW test stand and a modular pre-prototype at KIT. The industrial prototype was delivered to CRPP end of September 2011 and reached an output power of 2 MW at an efficiency of 45 % and with good RF beam pattern, in only four days of short pulse RF test. These results validated all design changes made in reaction to the results of the experiments in 2008. On the fifth experimental day, an internal absorber broke, terminating any further experiment with this tube. In parallel, design and experimental activities at KIT went on, in particular featuring reduced stray radiation down to 4% of the RF power. Next years’ plans for the 2 MW modular pre-prototype foresee a stepwise increase of pulse length.

Review of the conceptual design of a Doublet fusion experimental power reactor

International Nuclear Information System (INIS)

Baker, C.C.

1976-01-01

The results of a two-year, conceptual design study of a fusion experimental power reactor (EPR) are presented. For this study, the primary objectives of the EPR are to obtain plasma ignition conditions and produce net electrical power. The design features a Doublet plasma configuration with a major radius of 4.5 m. The average plasma beta is 10 percent which yields a thermonuclear power level of 410 MW during a 105-sec burn period. With a duty factor of 0.84, the gross electrical output is 124 MW(e) while the net output is 37 MW(e). The design features a 25-cm-thick, helium-cooled, modular, stainless-steel blanket with a 1-cm-thick, silicon carbide first wall. Sufficient shielding is provided to permit contact maintenance outside the shield envelope within 24 hr after shutdown. An overall plant concept has been developed including a superheated steam cycle power conversion system. Preliminary cost estimates and construction schedules have also been developed. 3 refs

Conceptual design studies of experimental and demonstration fusion reactors

International Nuclear Information System (INIS)

1978-01-01

Since 1973 the FINTOR Group has been involved in conceptual design studies of TOKAMAK-type fusion reactors to precede the construction of a prototype power reactor plant. FINTOR-1 was the first conceptual design aimed at investigating the main physics and engineering constraints on a minimum-size (both dimensions and thermal power) tokamak experimental reactor. The required plasma energy confinement time as evaluated by various power balance models was compared with the values resulting from different transport models. For the reference design, an energy confinement time ten times smaller than neoclassical was assumed. This also implied a rather high (thermally stable) working temperature (above 20 keV) for the reactor. Other relevant points of the design were: circular plasma cross section, single-null axisymmetric divertor; lithium breeder, stainless steel structures, helium coolant; modular blanket and shield structure; copper-stabilized, superconducting Nb-Ti toroidal field and divertor coils; vertical field and transformer coils inside the toroidal coils; vacuum-tight containment vessel. Solutions involving air and iron transformer cores were compared. These assumptions led to a minimum size reactor with a thermal power of about 100MW and rather large dimensions (major radius of about 9m) similar to those of full-scale power reactors considered in other conceptual studies. The FINTOR-1 analysis was completed by the end of 1976. In 1977 a conceptual design of a Demonstration Power Reactor Plant (FINTOR-D) was started. In this study the main working assumptions differing from those of FINTOR-1 are: non-circular plasma cross section; plasma confinement compatible with trapped ion instabilities; cold (gas) blanket sufficient for wall protection (no divertor); wall loading between 1-3MW/m 2 and thermal power of a few GW. (author)

Design of experimental system for supercritical CO2 fracturing under confining pressure conditions

Science.gov (United States)

Wang, H.; Lu, Q.; Li, X.; Yang, B.; Zheng, Y.; Shi, L.; Shi, X.

2018-03-01

Supercritical CO2 has the characteristics of low viscosity, high diffusion and zero surface tension, and it is considered as a new fluid for non-polluting and non-aqueous fracturing which can be used for shale gas development. Fracturing refers to a method of utilizing the high-pressure fluid to generate fractures in the rock formation so as to improve the oil and gas flow conditions and increase the oil and gas production. In this article, a new type of experimental system for supercritical CO2 fracturing under confining pressure conditions is designed, which is based on characteristics of supercritical CO2, shale reservoir and down-hole environment. The experimental system consists of three sub-systems, including supercritical CO2 generation system, supercritical CO2 fracturing system and data analysis system. It can be used to simulate supercritical CO2 fracturing under geo-stress conditions, thus to study the rock initiation pressure, the formation of the rock fractures, fractured surface morphology and so on. The experimental system has successfully carried out a series of supercritical CO2 fracturing experiments. The experimental results confirm the feasibility of the experimental system and the high efficiency of supercritical CO2 in fracturing tight rocks.

Quasi-experimental study designs series-paper 1: introduction: two historical lineages.

Science.gov (United States)

Bärnighausen, Till; Røttingen, John-Arne; Rockers, Peter; Shemilt, Ian; Tugwell, Peter

2017-09-01

The objective of this study was to contrast the historical development of experiments and quasi-experiments and provide the motivation for a journal series on quasi-experimental designs in health research. A short historical narrative, with concrete examples, and arguments based on an understanding of the practice of health research and evidence synthesis. Health research has played a key role in developing today's gold standard for causal inference-the randomized controlled multiply blinded trial. Historically, allocation approaches developed from convenience and purposive allocation to alternate and, finally, to random allocation. This development was motivated both by concerns for manipulation in allocation as well as statistical and theoretical developments demonstrating the power of randomization in creating counterfactuals for causal inference. In contrast to the sequential development of experiments, quasi-experiments originated at very different points in time, from very different scientific perspectives, and with frequent and long interruptions in their methodological development. Health researchers have only recently started to recognize the value of quasi-experiments for generating novel insights on causal relationships. While quasi-experiments are unlikely to replace experiments in generating the efficacy and safety evidence required for clinical guidelines and regulatory approval of medical technologies, quasi-experiments can play an important role in establishing the effectiveness of health care practice, programs, and policies. The papers in this series describe and discuss a range of important issues in utilizing quasi-experimental designs for primary research and quasi-experimental results for evidence synthesis. Copyright © 2017 Elsevier Inc. All rights reserved.

Overview of International Thermonuclear Experimental Reactor (ITER) engineering design activities*

Science.gov (United States)

Shimomura, Y.

1994-05-01

The International Thermonuclear Experimental Reactor (ITER) [International Thermonuclear Experimental Reactor (ITER) (International Atomic Energy Agency, Vienna, 1988), ITER Documentation Series, No. 1] project is a multiphased project, presently proceeding under the auspices of the International Atomic Energy Agency according to the terms of a four-party agreement among the European Atomic Energy Community (EC), the Government of Japan (JA), the Government of the Russian Federation (RF), and the Government of the United States (US), ``the Parties.'' The ITER project is based on the tokamak, a Russian invention, and has since been brought to a high level of development in all major fusion programs in the world. The objective of ITER is to demonstrate the scientific and technological feasibility of fusion energy for peaceful purposes. The ITER design is being developed, with support from the Parties' four Home Teams and is in progress by the Joint Central Team. An overview of ITER Design activities is presented.

Design of charge exchange recombination spectroscopy for the joint Texas experimental tokamak

Energy Technology Data Exchange (ETDEWEB)

Chi, Y.; Zhuang, G., E-mail: ge-zhuang@hust.edu.cn; Cheng, Z. F.; Hou, S. Y.; Cheng, C.; Li, Z.; Wang, J. R.; Wang, Z. J. [State Key Laboratory of Advanced Electromagnetic Engineering and Technology, Huazhong University of Science and Technology, Wuhan 430074 (China)

2014-11-15

The old diagnostic neutral beam injector first operated at the University of Texas at Austin is ready for rejoining the joint Texas experimental tokamak (J-TEXT). A new set of high voltage power supplies has been equipped and there is no limitation for beam modulation or beam pulse duration henceforth. Based on the spectra of fully striped impurity ions induced by the diagnostic beam the design work for toroidal charge exchange recombination spectroscopy (CXRS) system is presented. The 529 nm carbon VI (n = 8 − 7 transition) line seems to be the best choice for ion temperature and plasma rotation measurements and the considered hardware is listed. The design work of the toroidal CXRS system is guided by essential simulation of expected spectral results under the J-TEXT tokamak operation conditions.

Experimental application of design principles in corrosion research

International Nuclear Information System (INIS)

Smyrl, W.H.; Pohlman, S.L.

1977-01-01

Experimental design criteria for corrosion investigations are based on established principles for systems that have uniform, or nearly uniform, corrosive attack. Scale-up or scale-down may be accomplished by proper use of dimensionless groups that measure the relative importance of interfacial kinetics, solution conductivity, and mass transfer. These principles have been applied to different fields of corrosion which include materials selection testing and protection; and to a specific corrosion problem involving attack of a substrate through holes in a protective overplate

Study Design Rigor in Animal-Experimental Research Published in Anesthesia Journals.

Science.gov (United States)

Hoerauf, Janine M; Moss, Angela F; Fernandez-Bustamante, Ana; Bartels, Karsten

2018-01-01

Lack of reproducibility of preclinical studies has been identified as an impediment for translation of basic mechanistic research into effective clinical therapies. Indeed, the National Institutes of Health has revised its grant application process to require more rigorous study design, including sample size calculations, blinding procedures, and randomization steps. We hypothesized that the reporting of such metrics of study design rigor has increased over time for animal-experimental research published in anesthesia journals. PubMed was searched for animal-experimental studies published in 2005, 2010, and 2015 in primarily English-language anesthesia journals. A total of 1466 publications were graded on the performance of sample size estimation, randomization, and blinding. Cochran-Armitage test was used to assess linear trends over time for the primary outcome of whether or not a metric was reported. Interrater agreement for each of the 3 metrics (power, randomization, and blinding) was assessed using the weighted κ coefficient in a 10% random sample of articles rerated by a second investigator blinded to the ratings of the first investigator. A total of 1466 manuscripts were analyzed. Reporting for all 3 metrics of experimental design rigor increased over time (2005 to 2010 to 2015): for power analysis, from 5% (27/516), to 12% (59/485), to 17% (77/465); for randomization, from 41% (213/516), to 50% (243/485), to 54% (253/465); and for blinding, from 26% (135/516), to 38% (186/485), to 47% (217/465). The weighted κ coefficients and 98.3% confidence interval indicate almost perfect agreement between the 2 raters beyond that which occurs by chance alone (power, 0.93 [0.85, 1.0], randomization, 0.91 [0.85, 0.98], and blinding, 0.90 [0.84, 0.96]). Our hypothesis that reported metrics of rigor in animal-experimental studies in anesthesia journals have increased during the past decade was confirmed. More consistent reporting, or explicit justification for absence

Ice condenser experimental plan

International Nuclear Information System (INIS)

Kannberg, L.D.; Piepel, G.F.; Owczarski, P.C.; Liebetrau, A.M.

1986-01-01

An experimental plan is being developed to validate the computer code ICEDF. The code was developed to estimate the extent of aerosol retention in the ice compartments of pressurized water reactor ice condenser containment systems during severe accidents. The development of the experimental plan began with review of available information on the conditions under which the code will be applied. Computer-generated estimates of thermohydraulic and aerosol conditions entering the ice condenser were evaluated and along with other information, used to generate design criteria. The design criteria have been used for preliminary test assembly design and for generation of statistical test designs. Consideration of the phenomena to be evaluated in the testing program, as well as equipment and measurement limitations, have led to changes in the design criteria and to subsequent changes in the test assembly design and statistical test design. The overall strategy in developing the experimental plan includes iterative generation and evaluation of candidate test designs using computer codes for statistical test design and ICEDF for estimation of experimental results. Estimates of experimental variability made prior to actual testing will be verified by replicate testing at preselected design points

Accessibility and replacement as prime constraints in the design of large experimental tokamaks

International Nuclear Information System (INIS)

Challender, R.S.; Reynolds, P.

1976-01-01

An attempt is made to bring together those design features of large, experimental Tokamaks, which would lead to better accessibility during non-active operation and, in particular, permit replacement and repair after activation, thereby making possible an extended period of experimental operation into the ignition phase

Computer system for Monte Carlo experimentation

International Nuclear Information System (INIS)

Grier, D.A.

1986-01-01

A new computer system for Monte Carlo Experimentation is presented. The new system speeds and simplifies the process of coding and preparing a Monte Carlo Experiment; it also encourages the proper design of Monte Carlo Experiments, and the careful analysis of the experimental results. A new functional language is the core of this system. Monte Carlo Experiments, and their experimental designs, are programmed in this new language; those programs are compiled into Fortran output. The Fortran output is then compiled and executed. The experimental results are analyzed with a standard statistics package such as Si, Isp, or Minitab or with a user-supplied program. Both the experimental results and the experimental design may be directly loaded into the workspace of those packages. The new functional language frees programmers from many of the details of programming an experiment. Experimental designs such as factorial, fractional factorial, or latin square are easily described by the control structures and expressions of the language. Specific mathematical modes are generated by the routines of the language

Using factorial experimental design to evaluate the separation of plastics by froth flotation.

Science.gov (United States)

Salerno, Davide; Jordão, Helga; La Marca, Floriana; Carvalho, M Teresa

2018-03-01

This paper proposes the use of factorial experimental design as a standard experimental method in the application of froth flotation to plastic separation instead of the commonly used OVAT method (manipulation of one variable at a time). Furthermore, as is common practice in minerals flotation, the parameters of the kinetic model were used as process responses rather than the recovery of plastics in the separation products. To explain and illustrate the proposed methodology, a set of 32 experimental tests was performed using mixtures of two polymers with approximately the same density, PVC and PS (with mineral charges), with particle size ranging from 2 to 4 mm. The manipulated variables were frother concentration, air flow rate and pH. A three-level full factorial design was conducted. The models establishing the relationships between the manipulated variables and their interactions with the responses (first order kinetic model parameters) were built. The Corrected Akaike Information Criterion was used to select the best fit model and an analysis of variance (ANOVA) was conducted to identify the statistically significant terms of the model. It was shown that froth flotation can be used to efficiently separate PVC from PS with mineral charges by reducing the floatability of PVC, which largely depends on the action of pH. Within the tested interval, this is the factor that most affects the flotation rate constants. The results obtained show that the pure error may be of the same magnitude as the sum of squares of the errors, suggesting that there is significant variability within the same experimental conditions. Thus, special care is needed when evaluating and generalizing the process. Copyright © 2017 Elsevier Ltd. All rights reserved.

Mechanical design of the small-scale experimental ADS: MYRRHA

Energy Technology Data Exchange (ETDEWEB)

Maes, Dirk [SCKCEN, Reactor Physics and MYRRHA Department, Boeretang 200, B-2400 Mol (Belgium)

2006-10-15

Since 1998, SCK*CEN, in partnership with IBA s.a. and many European research laboratories, is designing a multipurpose Accelerator Driven System (ADS) - MYRRHA - and is conducting an associated R and D support programme. MYRRHA aims to serve as a basis for the European experimental ADS to provide protons and neutrons for various R and D applications. Besides an overall configuration of the MYRRHA reactor internals, the description in this paper is limited to the mechanical design of the main components of the Primary System and Associated Equipment (vessel and cover, diaphragm, spallation loop, sub-critical core, primary cooling system, emergency cooling system, in-vessel fuel storage and fuel transfer machine), the conceptual design of the robotics for In-Service Inspection and Repair (ISIR), together with the remote handling for operation and maintenance (O and M). (author)

Design of Experimental Suspended Footbridge with Deck Made of UHPC

Directory of Open Access Journals (Sweden)

Blank Marek

2016-01-01

Full Text Available This paper deals with the static and dynamic design of experimental footbridge for pedestrians and cyclists in the municipality Lužec nad Vltavou in Czech Republic, Europe. This work aims to familiarize the reader with calculations carried out and the results obtained, describing the static and dynamic properties of proposed footbridge. The construction of footbridge is designed as a suspended structure with prestressed bridge deck consisting of prefabricated UHPC panels and reversed “V” shaped steel pylon with height of approximately 40 meters. The deck is anchored using 24 steel hangers in one row in a steel pylon - 17 ropes in the main span and 7 cables on the other side. Range of the main span is 99.18 meters and the secondary span is 31.9 m. Deck width is 4.5 meters with 3.0 meters passing space. The bridge is designed for the possibility of passage of vehicles weighting up to 3.5 tons. Deck panels are made of UHPC with reinforcement. At the edge of the bridge on the side of the shorter span the bridge deck is firmly connected with abutment and on the other deck it is stored using a pair of sliding bearings. The utilization of the excellent properties of UHPC allows to design a very thin and lightweight construction of the deck, which could not be achieved with the use of normal concrete.

Aligning experimental design with bioinformatics analysis to meet discovery research objectives.

Science.gov (United States)

Kane, Michael D

2002-01-01

The utility of genomic technology and bioinformatic analytical support to provide new and needed insight into the molecular basis of disease, development, and diversity continues to grow as more research model systems and populations are investigated. Yet deriving results that meet a specific set of research objectives requires aligning or coordinating the design of the experiment, the laboratory techniques, and the data analysis. The following paragraphs describe several important interdependent factors that need to be considered to generate high quality data from the microarray platform. These factors include aligning oligonucleotide probe design with the sample labeling strategy if oligonucleotide probes are employed, recognizing that compromises are inherent in different sample procurement methods, normalizing 2-color microarray raw data, and distinguishing the difference between gene clustering and sample clustering. These factors do not represent an exhaustive list of technical variables in microarray-based research, but this list highlights those variables that span both experimental execution and data analysis. Copyright 2001 Wiley-Liss, Inc.

Application of Plackett-Burman experimental design in the development of muffin using adlay flour

Science.gov (United States)

Valmorida, J. S.; Castillo-Israel, K. A. T.

2018-01-01

The application of Plackett-Burman experimental design was made to identify significant formulation and process variables in the development of muffin using adlay flour. Out of the seven screened variables, levels of sugar, levels of butter and baking temperature had the most significant influence on the product model in terms of physicochemical and sensory acceptability. Results of the experiment further demonstrate the effectiveness of Plackett-Burman design in choosing the best adlay variety for muffin production. Hence, the statistical method used in the study permits an efficient selection of important variables needed in the development of muffin from adlay which can be optimized using response surface methodology.

Development and first experimental results of the KERENA Passive Outflow Reducer

Energy Technology Data Exchange (ETDEWEB)

Dumond, Julien; Maisberger, Fabian [AREVA NP GmbH (Germany); Class, Andreas [Karlsruher Institut fuer Technologie (Germany)

2012-11-01

component, the parallel disposition was adopted (section 1.3). To validate the principle of the POR and optimize the geometry, experiments are carried out at AREVA Technical Center in Karlstein (chapter 2). The experimental setup is depicted in section 2.1 and the first experimental results are described and discussed in section 2.2. (orig.)

Development and first experimental results of the KERENA Passive Outflow Reducer

International Nuclear Information System (INIS)

Dumond, Julien; Maisberger, Fabian; Class, Andreas

2012-01-01

component, the parallel disposition was adopted (section 1.3). To validate the principle of the POR and optimize the geometry, experiments are carried out at AREVA Technical Center in Karlstein (chapter 2). The experimental setup is depicted in section 2.1 and the first experimental results are described and discussed in section 2.2. (orig.)

Verification of fire and explosion accident analysis codes (facility design and preliminary results)

International Nuclear Information System (INIS)

Gregory, W.S.; Nichols, B.D.; Talbott, D.V.; Smith, P.R.; Fenton, D.L.

1985-01-01

For several years, the US Nuclear Regulatory Commission has sponsored the development of methods for improving capabilities to analyze the effects of postulated accidents in nuclear facilities; the accidents of interest are those that could occur during nuclear materials handling. At the Los Alamos National Laboratory, this program has resulted in three computer codes: FIRAC, EXPAC, and TORAC. These codes are designed to predict the effects of fires, explosions, and tornadoes in nuclear facilities. Particular emphasis is placed on the movement of airborne radioactive material through the gaseous effluent treatment system of a nuclear installation. The design, construction, and calibration of an experimental ventilation system to verify the fire and explosion accident analysis codes are described. The facility features a large industrial heater and several aerosol smoke generators that are used to simulate fires. Both injected thermal energy and aerosol mass can be controlled using this equipment. Explosions are simulated with H 2 /O 2 balloons and small explosive charges. Experimental measurements of temperature, energy, aerosol release rates, smoke concentration, and mass accumulation on HEPA filters can be made. Volumetric flow rate and differential pressures also are monitored. The initial experiments involve varying parameters such as thermal and aerosol rate and ventilation flow rate. FIRAC prediction results are presented. 10 figs

Design and prototype results of a far-infrared interferometer for MFTF-B

International Nuclear Information System (INIS)

Monjes, J.A.; Throop, A.L.; Thomas, S.R.; Peebles, A.; Zu, Qin-Zin.

1983-01-01

A Far-Infrared (FIR) Laser Interferometer (FLI), operating at 185 μm wavelength is planned as part of the initial start-up set of plasma diagnostics for the Mirror Fusion Test Facility (MFTF-B). The FLI will consist of a heterodyne, three-chord laser interferometer which will be used initially to measure line-integrated plasma density in the high-density, center cell region of the machine. The conceptual system design and analysis has been completed. There are several unique environmental/physical constraints and performance requirements for this system which have required that technology-evaluation and prototyping experiments be completed to support the design effort and confirm the expected performance parameters. Issues which have been addressed include extensive use of long-path dielectric waveguide, coupling and control of free-space propagation of the beam, and polarization control. The results and conclusions of the design analysis and experimental measurements will be presented

Selecting and Improving Quasi-Experimental Designs in Effectiveness and Implementation Research.

Science.gov (United States)

Handley, Margaret A; Lyles, Courtney R; McCulloch, Charles; Cattamanchi, Adithya

2018-04-01

Interventional researchers face many design challenges when assessing intervention implementation in real-world settings. Intervention implementation requires holding fast on internal validity needs while incorporating external validity considerations (such as uptake by diverse subpopulations, acceptability, cost, and sustainability). Quasi-experimental designs (QEDs) are increasingly employed to achieve a balance between internal and external validity. Although these designs are often referred to and summarized in terms of logistical benefits, there is still uncertainty about (a) selecting from among various QEDs and (b) developing strategies to strengthen the internal and external validity of QEDs. We focus here on commonly used QEDs (prepost designs with nonequivalent control groups, interrupted time series, and stepped-wedge designs) and discuss several variants that maximize internal and external validity at the design, execution and implementation, and analysis stages.

Design and preliminary test results of the quench detection system for IFSMTF

International Nuclear Information System (INIS)

Shen, S.S.; Walstrom, P.L.; Wilson, C.T.; Goddard, J.S.

1985-01-01

A unique quench detection system was designed for the International Fusion Superconducting Magnet Test Facility (IFSMTF), where a simultaneous test of six large superconducting toroidal field magnets will be carried out. The scheme was based on analog subtraction of self and neighboring pickup winding voltage from the coil voltage to yield a compensated signal proportional to a normal-zone voltage. The compensated signals were input to quench detection modules that give a quench output signal to discharge the coil if the compensated signals exceed preset thresholds for preset time durations. This paper summarizes the design and analysis of the system and presents the experimental results of the simulation tests, two-coil charging-discharging tests, and the normal-zone recovery tests

Physics design and experimental study of tokamak divertor

International Nuclear Information System (INIS)

Yan Jiancheng; Gao Qingdi; Yan Longwen; Wang Mingxu; Deng Baiquan; Zhang Fu; Zhang Nianman; Ran Hong; Cheng Fayin; Tang Yiwu; Chen Xiaoping

2007-06-01

The divertor configuration of HL-2A tokamak is optimized, and the plasma performance in divertor is simulated with B2-code. The effects of collisionality on plasma-wall transition in the scrape-off layer of divertor are investigated, high performances of the divertor plasma in HL-2A are simulated, and a quasi- stationary RS operation mode is established with the plasma controlled by LHCD and NBI. HL-2A tokamak has been successfully operated in divertor configuration. The major parameters: plasma current I p =320 kA, toroidal field B t =2.2 T, plasma discharger duration T d =1580 ms ware achieved at the end of 2004. The preliminary experimental researches of advanced diverter have been carried out. Design studies of divertor target plate for high power density fusion reactor have been carried out, especially, the physical processes on the surface of flowing liquid lithium target plate. The exploration research of improving divertor ash removal efficiency and reducing tritium inventory resulting from applying the RF ponderomotive force potential is studied. The optimization structure design studies of FEB-E reactor divertor are performed. High flux thermal shock experiments were carried on tungsten and carbon based materials. Hot Isostatic Press (HIP) method was employed to bond tungsten to copper alloys. Electron beam simulated thermal fatigue tests were also carried out to W/Cu bondings. Thermal desorption and surface modification of He + implanted into tungsten have been studied. (authors)

Superconducting coil design for a tokamak experimental power reactor

International Nuclear Information System (INIS)

Turner, L.R.; Wang, S.T.; Smelser, P.

1977-01-01

Superconducting toroidal field (TF) and polodial-field (PF) coils have been designed for the proposed Argonne National Laboratory experimental power reactor (EPR). Features of the design include: (1) Peak field of 8 T at 4.2 K or 10 T at 3.0 K. (2) Constant-tension shape for the TF coils, corrected for the finite number (16) of coils. (3) Analysis of errors in coil alignment. (4) Comparison of safety aspects of series-connected and parallel-connected coils. (5) A 60 kA sheet conductor of NbTi with copper stabilizer and stainless steel for support. (6) Superconducting PF coils outside the TF coils. (7) The TF coils shielded from pulsed fields by high-purity aluminum

Pilot plant SERSE: Description and results of the experimental tests under treatment of simulated chemical liquid waste

International Nuclear Information System (INIS)

Calle, C.; Gili, M.; Luce, A.; Marrocchelli, A.; Pietrelli, L.; Troiani, F.

1989-11-01

The chemical processes for the selective separation of the actinides and long lived fission products from aged liquid wastes is described. The SERSE pilot plant is a cold facility which has been designed, by ENEA, for the engineering scale demonstration of the chemical separation processes. The experimental tests carried out in the plant are described and the results confirm the laboratory data. (author)

A Simulation Study of Threats to Validity in Quasi-Experimental Designs: Interrelationship between Design, Measurement, and Analysis.

Science.gov (United States)

Holgado-Tello, Fco P; Chacón-Moscoso, Salvador; Sanduvete-Chaves, Susana; Pérez-Gil, José A

2016-01-01

The Campbellian tradition provides a conceptual framework to assess threats to validity. On the other hand, different models of causal analysis have been developed to control estimation biases in different research designs. However, the link between design features, measurement issues, and concrete impact estimation analyses is weak. In order to provide an empirical solution to this problem, we use Structural Equation Modeling (SEM) as a first approximation to operationalize the analytical implications of threats to validity in quasi-experimental designs. Based on the analogies established between the Classical Test Theory (CTT) and causal analysis, we describe an empirical study based on SEM in which range restriction and statistical power have been simulated in two different models: (1) A multistate model in the control condition (pre-test); and (2) A single-trait-multistate model in the control condition (post-test), adding a new mediator latent exogenous (independent) variable that represents a threat to validity. Results show, empirically, how the differences between both the models could be partially or totally attributed to these threats. Therefore, SEM provides a useful tool to analyze the influence of potential threats to validity.

Los Alamos Experimental Engineering Waste Burial Facility: design considerations and preliminary experimental plan

International Nuclear Information System (INIS)

DePoorter, G.L.

1981-01-01

The Experimental Engineered Waste Burial Facility is a field test site where generic experiments can be performed on several scales to get the basic information necessary to understand the processes occurring in low-level waste disposal facilities. The experiments include hydrological, chemical, mechanical, and biological factors. In order to separate these various factors in the experiments and to extrapolate the experimental results to actual facilities, experiments will be performed on several different scales

Defining Dynamic Characteristics of Multilink Pendulum System with Comparison of the Calculated and Experimental Results

Directory of Open Access Journals (Sweden)

V. A. Gribkov

2015-01-01

Full Text Available We consider the multilink pendulum system consisting of six physical pendulums. A pendulum (carrier has inertia parameters, which significantly exceed the remaining (carried ones placed on the carrier. In addition to the system under analysis, in particular, the paper presents a design scheme for a two-stage liquid fuel rocket using pendulums as the analogues of fluctuating fuel. Pendulum models also find application to solve problems of stabilization of space tether systems. The objective of the study is to determine dynamic characteristics of the said sixmembered pendulum system, as well as to identify specific dynamic properties inherent in objects of this kind. Dynamic characteristics of the system are determined by calculations. A physical model of the pendulum allowed us to compare the calculated and experimental results. To conduct the frequency tests of the pendulum model three pilot units have been created. The first two units turned out to be inappropriate for fulfilling the experimental tasks for various reasons. The third unit enabled us to obtain desirable experimental results. The "calculation–experiment” discrepancy on the natural frequencies of the pendulum model for the majority of frequencies was less than 5%. We analyzed the dynamic features of multilink pendulum systems "carried by the carrier unit links". The analysis results are applicable to the above-noted object classes of rocket and space technology.

Tasks related to increase of RA reactor exploitation and experimental potential, 03. Crane for handling the vertical experimental channels of the RA reactor - design project

International Nuclear Information System (INIS)

Pavicevic, M.

1963-07-01

Within the work related to improvement of experimental potential of the RA reactor, this document describes the design project of the new crane for handling the vertical experimental channels of the RA reactor, engineering drawings of the crane main elements, mechanical part, design project of the electrical part of the crane and cost estimation

Numerical and experimental results of a passive free yawing downwind wind turbine

Energy Technology Data Exchange (ETDEWEB)

Verelst, D.R.S.

2013-09-15

The background of this PhD study concerns a medium sized 3 bladed wind turbine in a free yawing and downwind configuration. Largely funded by an EU Marie-Curie IAPP grant, the project was jointly setup by the renewable energy consultant 3E, DTU Wind Energy and the TU Delft. The 3 bladed free yawing downwind concept is pursued in an attempt to increase the robustness of a wind turbine by eliminating the traditionally actively controlled, and sometimes failure prone yawing mechanism. Under certain conditions, such as for remote (off shore) and off grid applications, a decreased failure rate can increase the economical competitiveness significantly compared to more traditional power supplies. This work presents aeroelastic analysis and results of a wind tunnel test campaign for the 3 bladed free yawing downwind concept. The investigated topics concern free yawing stability and how it is affected by coning angle, blade sweep, and blade flexibility using both numerical and experimental methods. The wind tunnel tests were organized in the Open Jet Facility of the TU Delft, and the thesis discusses the experiment's design, construction, operation, and gives an analysis of the results. It provides a dataset to compare aeroelastic simulations with experimental results for varying yawed inflow conditions and free yawing stability. The experimental data scope is limited to rotor speed, tower base bending moment, yaw angle, and blade root flapwise bending moments measurements. Other work covered during the PhD study is a parametric blade sweep investigation for the NREL 5MW turbine, and a detailed study on load extrapolation methods based on aeroelastic simulations. It is concluded that the 3 bladed, free yawing, and downwind wind turbine can operate in a stable manner. However, numerical studies indicate a less stable operating region when the rotor flow is about to stall. The experiments confirmed the free yawing stability, but the unstable region indicated in the

Variable Entry Biased Paracentric Hemispherical Deflector: Experimental results on energy resolution for different entry positions

Science.gov (United States)

Dogan, Mevlut; Ulu, Melike; Gennerakis, Giannis; Zouros, Theo J. M.

2014-04-01

A new hemispherical deflector analyzer (HDA) which is designed for electron energy analysis in atomic collisions has been constructed and tested. Using the crossed beam technique at the electron spectrometer, test measurements were performed for electron beam (200 eV) - Helium atoms interactions. These first experimental results show that the paracentric entries give almost twice as good resolution as that for the conventional entry. Supporting simulations of the entire lens+HDA spectrometer are found in relatively good agreement with experiment.

Design, experimental investigation and multi-objective optimization of a small-scale radial compressor for heat pump applications

Energy Technology Data Exchange (ETDEWEB)

Schiffmann, J. [Fischer Engineering Solutions AG, Birkenweg 3, CH-3360 Herzogenbuchsee (Switzerland); Favrat, D. [Ecole Polytechnique Federale de Lausanne, EPFL STI IGM LENI, Station 9, CH-1015 Lausanne (Switzerland)

2010-01-15

The main driver for small scale turbomachinery in domestic heat pumps is the potential for reaching higher efficiencies than volumetric compressors currently used and the potential for making the compressor oil-free, bearing a considerable advantage in the design of advanced multi-stage heat pump cycles. An appropriate turbocompressor for driving domestic heat pumps with a high temperature lift requires the ability to operate on a wide range of pressure ratios and mass flows, confronting the designer with the necessity of a compromise between range and efficiency. The present publication shows a possible way to deal with that difficulty, by coupling an appropriate modeling tool to a multi-objective optimizer. The optimizer manages to fit the compressor design into the possible specifications field while keeping the high efficiency on a wide operational range. The 1D-tool used for the compressor stage modeling has been validated by experimentally testing an initial impeller design. The excellent experimental results, the agreement with the model and the linking of the model to a multi-objective optimizer will allow to design radial compressor stages managing to fit the wide operational range of domestic heat pumps while keeping the high efficiency level. (author)

Development of human factors experimental evaluation techniques - Human factors design and evaluation of the main control room of atomic power plants using visual display terminals

Energy Technology Data Exchange (ETDEWEB)

Han, Sung Ho; Chung, Min Kyun; Choi, Kyung Lim; Song, Young Woong; Eoh, Hong Joon; Lee, In Suk; Kim, Bom Soo; Yeo, Yun Shin; Lee, Haeo Sun [Pohang University of Science and Technology, Pohang (Korea, Republic of)

1995-07-01

This study was conducted to build a prototype of the operator interface on a visual display terminal, and to provide a framework for using and applying prototyping techniques. A typical subsystem of an MCR was prototyped and validated by operator testing. Lessons learned during the development as well as prototyping techniques were described in this report for an efficient development. In addition, human factors experimental plans were surveyed and summarized for evaluating new design alternatives as well as the current design of the operator interface. The major results of this study are listed as follow: A method for designing an operator interface prototype on a VDT, A prototype of the operator interface of a typical subsystem, Guidelines for applying prototyping techniques, Characteristics and major considerations of experimental plans, Guidelines for applying prototyping techniques, Characteristics and major considerations of experimental plans, Guidelines for analyzing experimental data, A paradigm for human factors experimentation including experimental designs, procedures, and data analyses. 27 refs., 60 tabs., 47 figs. (author)

General description of preliminary design of an experimental fusion reactor and the future problems

International Nuclear Information System (INIS)

Sako, Kiyoshi

1976-01-01

Recently, the studies on plasma physics has progressed rapidly, and promising experimental data emerged successively. Especially expectation mounts high that Tokamak will develop into power reactors. In Japan, the construction of large plasma devices such as JT-60 of JAERI is going to start, and after several years, the studies on plasma physics will come to the end of first stage, then the main research and development will be directed to power reactors. The studies on the design of practical fusion reactors have been in progress since 1973 in JAERI, and the preliminary design is being carried out. The purposes of the preliminary design are the clarification of the concept of the experimental reactor and the requirements for the studies on core plasma, the examination of the problems for developing main components and systems of the reactor, and the development of design technology. The experimental reactor is the quasi-steady reactor of 100 MW fusion reaction output, and the conditions set for the design and the basis of their setting are explained. The outline of the design, namely core plasma, blankets, superconductive magnets and the shielding with them, vacuum wall, neutral particle injection heating device, core fuel supply and exhaust system, and others, is described. In case of scale-up the reactor structural material which can withstand neutron damage must be developed. (Kako, I.)

Mirrors design, analysis and manufacturing of the 550mm Korsch telescope experimental model

Science.gov (United States)

Huang, Po-Hsuan; Huang, Yi-Kai; Ling, Jer

2017-08-01

In 2015, NSPO (National Space Organization) began to develop the sub-meter resolution optical remote sensing instrument of the next generation optical remote sensing satellite which follow-on to FORMOSAT-5. Upgraded from the Ritchey-Chrétien Cassegrain telescope optical system of FORMOSAT-5, the experimental optical system of the advanced optical remote sensing instrument was enhanced to an off-axis Korsch telescope optical system which consists of five mirrors. It contains: (1) M1: 550mm diameter aperture primary mirror, (2) M2: secondary mirror, (3) M3: off-axis tertiary mirror, (4) FM1 and FM2: two folding flat mirrors, for purpose of limiting the overall volume, reducing the mass, and providing a long focal length and excellent optical performance. By the end of 2015, we implemented several important techniques including optical system design, opto-mechanical design, FEM and multi-physics analysis and optimization system in order to do a preliminary study and begin to develop and design these large-size lightweight aspheric mirrors and flat mirrors. The lightweight mirror design and opto-mechanical interface design were completed in August 2016. We then manufactured and polished these experimental model mirrors in Taiwan; all five mirrors ware completed as spherical surfaces by the end of 2016. Aspheric figuring, assembling tests and optical alignment verification of these mirrors will be done with a Korsch telescope experimental structure model in 2018.

Design and experimental study of a novel giant magnetostrictive actuator

Energy Technology Data Exchange (ETDEWEB)

Xue, Guangming, E-mail: yy0youxia@163.com [Vehicle and Electrical Engineering Department, Ordnance Engineering College, Shijiazhuang, 050003 China (China); Zhang, Peilin; He, Zhongbo; Li, Dongwei; Huang, Yingjie [Vehicle and Electrical Engineering Department, Ordnance Engineering College, Shijiazhuang, 050003 China (China); Xie, Wenqiang [Cadre Rotational Training Brigade, Ordnance Engineering College, Shijiazhuang, 050003 China (China)

2016-12-15

Giant magnetostrictive actuator has been widely used in precise driving occasions for its excellent performance. However, in driving a switching valve, especially the ball-valve in an electronic controlled injector, the actuator can’t exhibit its good performance for limits in output displacement and responding speed. A novel giant magnetostrictive actuator, which can reach its maximum displacement for being exerted with no bias magnetic field, is designed in this paper. Simultaneously, elongating of the giant magetostrictive material is converted to shortening of the actuator's axial dimension with the help of an output rod in “T” type. Furthermore, to save responding time, the driving voltage with high opening voltage while low holding voltage is designed. Responding time and output displacement are studied experimentally with the help of a measuring system. From measured results, designed driving voltage can improve the responding speed of actuator displacement quite effectively. And, giant magnetostrictive actuator can output various steady-state displacements to reach more driving effects. - Highlights: • GMA with zero bias magnetic field can reach maximum displacement in one direction. • Driving wave with high opening voltage can promote GMA's responding speed. • Higher opening voltage is exerted, less rise time is reached. • Continuous displacements from 0 to maximum value can be achieved by GMA.

Calibration of an experimental model of tritium storage bed designed for 'in situ' accountability

International Nuclear Information System (INIS)

Bidica, Nicolae; Stefanescu, Ioan; Bucur, Ciprian; Bulubasa, Gheorghe; Deaconu, Mariea

2009-01-01

Full text: Objectives: Tritium accountancy of the storage beds in tritium facilities is an important issue for tritium inventory control. The purpose of our work was to perform calibration of an experimental model of tritium storage bed with a special design, using electric heaters to simulate tritium decay, and to evaluate the detection limit of the accountancy method. The objective of this paper is to present an experimental method used for calibration of the storage bed and the experimental results consisting of calibration curves and detection limit. Our method is based on a 'self-assaying' tritium storage bed. The basic characteristics of the design of our storage bed consists, in principle, of a uniform distribution of the storage material on several copper thin fins (in order to obtain a uniform temperature field inside the bed), an electrical heat source to simulate the tritium decay heat, a system of thermocouples for measuring the temperature field inside the bed, and good thermal isolation of the bed from the external environment. Within this design of the tritium storage bed, the tritium accounting method is based on determining the decay heat of tritium by measuring the temperature increase of the isolated storage bed. Experimental procedure consisted in measuring of temperature field inside the bed for few values of the power injected with the aid of electrical heat source. Data have been collected for few hours and the temperature increase rate was determined for each value of the power injected. Graphical representation of temperature rise versus injected powers was obtained. This accounting method of tritium inventory stored as metal tritide is a reliable solution for in-situ tritium accountability in a tritium handling facility. Several improvements can be done regarding the design of the storage bed in order to improve the measurement accuracy and to obtain a lower detection limit as for instance use of more accurate thermocouples or special

Bayesian Optimal Experimental Design Using Multilevel Monte Carlo

KAUST Repository

Ben Issaid, Chaouki

2015-05-12

Experimental design can be vital when experiments are resource-exhaustive and time-consuming. In this work, we carry out experimental design in the Bayesian framework. To measure the amount of information that can be extracted from the data in an experiment, we use the expected information gain as the utility function, which specifically is the expected logarithmic ratio between the posterior and prior distributions. Optimizing this utility function enables us to design experiments that yield the most informative data about the model parameters. One of the major difficulties in evaluating the expected information gain is that it naturally involves nested integration over a possibly high dimensional domain. We use the Multilevel Monte Carlo (MLMC) method to accelerate the computation of the nested high dimensional integral. The advantages are twofold. First, MLMC can significantly reduce the cost of the nested integral for a given tolerance, by using an optimal sample distribution among different sample averages of the inner integrals. Second, the MLMC method imposes fewer assumptions, such as the asymptotic concentration of posterior measures, required for instance by the Laplace approximation (LA). We test the MLMC method using two numerical examples. The first example is the design of sensor deployment for a Darcy flow problem governed by a one-dimensional Poisson equation. We place the sensors in the locations where the pressure is measured, and we model the conductivity field as a piecewise constant random vector with two parameters. The second one is chemical Enhanced Oil Recovery (EOR) core flooding experiment assuming homogeneous permeability. We measure the cumulative oil recovery, from a horizontal core flooded by water, surfactant and polymer, for different injection rates. The model parameters consist of the endpoint relative permeabilities, the residual saturations and the relative permeability exponents for the three phases: water, oil and

Design, Simulation and Experimental Investigation of a Solar System Based on PV Panels and PVT Collectors

Directory of Open Access Journals (Sweden)

Annamaria Buonomano

2016-06-01

Full Text Available This paper presents numerical and experimental analyses aimed at evaluating the technical and economic feasibility of photovoltaic/thermal (PVT collectors. An experimental setup was purposely designed and constructed in order to compare the electrical performance of a PVT solar field with the one achieved by an identical solar field consisting of conventional photovoltaic (PV panels. The experimental analysis also aims at evaluating the potential advantages of PVT vs. PV in terms of enhancement of electrical efficiency and thermal energy production. The installed experimental set-up includes four flat polycrystalline silicon PV panels and four flat unglazed polycrystalline silicon PVT collectors. The total electrical power and area of the solar field are 2 kWe and 13 m2, respectively. The experimental set-up is currently installed at the company AV Project Ltd., located in Avellino (Italy. This study also analyzes the system from a numerical point of view, including a thermo-economic dynamic simulation model for the design and the assessment of energy performance and economic profitability of the solar systems consisting of glazed PVT and PV collectors. The experimental setup was modelled and partly simulated in TRNSYS environment. The simulation model was useful to analyze efficiencies and temperatures reached by such solar technologies, by taking into account the reference technology of PVTs (consisting of glazed collectors as well as to compare the numerical data obtained by dynamic simulations with the gathered experimental results for the PV technology. The numerical analysis shows that the PVT global efficiency is about 26%. Conversely, from the experimental point of view, the average thermal efficiency of PVT collectors is around 13% and the electrical efficiencies of both technologies are almost coincident and equal to 15%.

Design studies of back up cores for the experimental multi-purpose VHTR, (1)

International Nuclear Information System (INIS)

Yasuno, Takehiko; Miyamoto, Yoshiaki; Mitake, Susumu

1982-09-01

For the Experimental Multi-Purpose Very High Temperature Reactor, design studies have been made of two backup cores loaded with new type fuel elements. The purpose is to improve core operational characteristics of the standard design core (Mark-III core) consisting of pin-in-block type fuel element having externally cooled hollow fuel rods. The first backup core (semi-pin fuel core) is composed of fuel elements with internally cooled fuel pins, and the second core (multihole fuel core) is composed of multihole fuel elements, which can be adopted for the experimental VHTR as the substitution of the standard Mark-III fuel element. Either of the cores has 73 fuel columns and 4 m height. The arrangement of active core and reactor internal structure is same as that in the standard design core. These backup cores meet almost all design requirements of the VHTR and increase the margins for some important design items in comparison with the standard core (Mark-III core). This report describes the overall characteristics of nuclear, thermal-hydraulic, fuel and safety, and structural consideration for these cores. (author)

Pre-design stage of the intermediate heat exchanger for experimental fast reactor

International Nuclear Information System (INIS)

Luz, M.; Borges, E.M.; Braz Filho, F.A.; Hirdes, V.R.

1986-09-01

This report presents the outlines of a thermal-hydraulic calculation procedure for the pre-design stage of the Intermediate Heat Exchanger for a 5 MW Experimental Fast Reactor (EFR), which can be used in other similar projects, at the same stage of evolution. Heat transfer and heat loss computations for the preliminary design of the heat exchanger are presented. (author) [pt

Experimental design optimisation: theory and application to estimation of receptor model parameters using dynamic positron emission tomography

International Nuclear Information System (INIS)

Delforge, J.; Syrota, A.; Mazoyer, B.M.

1989-01-01

General framework and various criteria for experimental design optimisation are presented. The methodology is applied to estimation of receptor-ligand reaction model parameters with dynamic positron emission tomography data. The possibility of improving parameter estimation using a new experimental design combining an injection of the β + -labelled ligand and an injection of the cold ligand is investigated. Numerical simulations predict remarkable improvement in the accuracy of parameter estimates with this new experimental design and particularly the possibility of separate estimations of the association constant (k +1 ) and of receptor density (B' max ) in a single experiment. Simulation predictions are validated using experimental PET data in which parameter uncertainties are reduced by factors ranging from 17 to 1000. (author)

A statistical approach to the experimental design of the sulfuric acid leaching of gold-copper ore

Directory of Open Access Journals (Sweden)

Mendes F.D.

2003-01-01

Full Text Available The high grade of copper in the Igarapé Bahia (Brazil gold-copper ore prevents the direct application of the classic cyanidation process. Copper oxides and sulfides react with cyanides in solution, causing a high consumption of leach reagent and thereby raising processing costs and decreasing recovery of gold. Studies have showm that a feasible route for this ore would be a pretreatment for copper minerals removal prior to the cyanidation stage. The goal of this experimental work was to study the experimental conditions required for copper removal from Igarapé Bahia gold-copper ore by sulfuric acid leaching by applying a statistical approach to the experimental design. By using the Plackett Burman method, it was possible to select the variables that had the largest influence on the percentage of copper extracted at the sulfuric acid leaching stage. These were temperature of leach solution, stirring speed, concentration of sulfuric acid in the leach solution and particle size of the ore. The influence of the individual effects of these variables and their interactions on the experimental response were analyzed by applying the replicated full factorial design method. Finally, the selected variables were optimized by the ascending path statistical method, which determined the best experimental conditions for leaching to achieve the highest percentage of copper extracted. Using the optimized conditions, the best leaching results showed a copper extraction of 75.5%.

A survey of Wien bridge-based chaotic oscillators: Design and experimental issues

International Nuclear Information System (INIS)

Kilic, Recai; Yildirim, Fatma

2008-01-01

This paper presents a comparative study on design and implementation of Wien type chaotic oscillators. By making a collection of almost all Wien bridge-based chaotic circuits, we have investigated these oscillators in terms of chaotic dynamics, circuit structures, active building blocks, nonlinear element structures and operating frequency by using PSpice simulations and laboratory experiments. In addition to this comparative investigation, we present our two basic experimental contributions to referred implementations. While the first of our experimental contributions consists of the experimentally implementation of CFOA-based Chua's circuit modified for very high chaotic oscillations, the scope of the second is to experimentally implement a Wien type high frequency chaos generator, which has the diode-inductor composite, in the inductorless form by using CFOA-based synthetic inductor

Design and experimental tests of a novel neutron spin analyzer for wide angle spin echo spectrometers

Energy Technology Data Exchange (ETDEWEB)

Fouquet, Peter; Farago, Bela; Andersen, Ken H.; Bentley, Phillip M.; Pastrello, Gilles; Sutton, Iain; Thaveron, Eric; Thomas, Frederic [Institut Laue-Langevin, BP 156, F-38042 Grenoble Cedex 9 (France); Moskvin, Evgeny [Helmholtzzentrum Berlin, Glienicker Strasse 100, D-14109 Berlin (Germany); Pappas, Catherine [Helmholtzzentrum Berlin, Glienicker Strasse 100, D-14109 Berlin (Germany); Faculty of Applied Sciences, Delft University of Technology, Mekelweg 15, 2629 JB Delft (Netherlands)

2009-09-15

This paper describes the design and experimental tests of a novel neutron spin analyzer optimized for wide angle spin echo spectrometers. The new design is based on nonremanent magnetic supermirrors, which are magnetized by vertical magnetic fields created by NdFeB high field permanent magnets. The solution presented here gives stable performance at moderate costs in contrast to designs invoking remanent supermirrors. In the experimental part of this paper we demonstrate that the new design performs well in terms of polarization, transmission, and that high quality neutron spin echo spectra can be measured.

Experimental Verification of Current Shear Design Equations for HSRC Beams

Directory of Open Access Journals (Sweden)

Attaullah Shah

2012-07-01

Full Text Available Experimental research on the shear capacity of HSRC (High Strength Reinforced Concrete beams is relatively very limited as compared to the NSRC (Normal Strength Reinforced Concrete beams. Most of the Building Codes determine the shear strength of HSRC with the help of empirical equations based on experimental work of NSRC beams and hence these equations are generally regarded as un-conservative for HSRC beams particularly at low level of longitudinal reinforcement. In this paper, 42 beams have been tested in two sets, such that in 21 beams no transverse reinforcement has been used, whereas in the remaining 21 beams, minimum transverse reinforcement has been used as per ACI-318 (American Concrete Institute provisions. Two values of compressive strength 52 and 61 MPa, three values of longitudinal steel ratio and seven values of shear span to depth ratio have been have been used. The beams were tested under concentrated load at the mid span. The results are compared with the equations proposed by different international building codes like ACI, AASHTO LRFD, EC (Euro Code, Canadian Code and Japanese Code for shear strength of HSRC beams.From comparison, it has been observed that some codes are less conservative for shear design of HSRC beams and further research is required to rationalize these equations.

Design and experimental investigation of a second harmonic 20 kW class 28 GHz gyrotron for evaluation of new emitter technologies

Energy Technology Data Exchange (ETDEWEB)

Malygin, Anton

2016-07-01

Gyrotrons are high-power mm-wave tubes. Here, the design, construction and experimental investigation of a 20 kW, 28 GHz gyrotron (2nd harmonic) are reported. This tube was designed to evaluate new emitters for future highly efficient and reliable fusion gyrotrons and for material processing applications. Following experimental results have been achieved in CW operation: 22.5 kW output power at 23.4 kV electron beam voltage and 2.23 A beam current with the world record efficiency of 43 %.

The interactive design collaboratorium

DEFF Research Database (Denmark)

Bødker, Susanne; Petersen, Marianne Graves; Krogh, Peter Gall

2001-01-01

This paper reports on experimental process in which a prototype was developed of an interactive design collaboatorium, in cooperation with a group of usability designers. In a longterm research cooperation, this usability group has changed its work practice in order to work in the design...... collaboratorium. The design collaboratorium was developed to move usability design away from a lab towards an open physical and organizational space where designer, users and engineers meet and collaborate, or work alongside each other. The cooperation between researchers and the usability gruop has resulted...... in practical experimentation in projects and in design of an experimental design collaboratorium emploing electronic whiteboards, 3D design documentation, etc. This experimental prototype has been evaluated in cooperative workshops. We report on the results of this evaluation....

Design and experimental validation for direct-drive fault-tolerant permanent-magnet vernier machines.

Science.gov (United States)

Liu, Guohai; Yang, Junqin; Chen, Ming; Chen, Qian

2014-01-01

A fault-tolerant permanent-magnet vernier (FT-PMV) machine is designed for direct-drive applications, incorporating the merits of high torque density and high reliability. Based on the so-called magnetic gearing effect, PMV machines have the ability of high torque density by introducing the flux-modulation poles (FMPs). This paper investigates the fault-tolerant characteristic of PMV machines and provides a design method, which is able to not only meet the fault-tolerant requirements but also keep the ability of high torque density. The operation principle of the proposed machine has been analyzed. The design process and optimization are presented specifically, such as the combination of slots and poles, the winding distribution, and the dimensions of PMs and teeth. By using the time-stepping finite element method (TS-FEM), the machine performances are evaluated. Finally, the FT-PMV machine is manufactured, and the experimental results are presented to validate the theoretical analysis.

Design and Experimental Validation for Direct-Drive Fault-Tolerant Permanent-Magnet Vernier Machines

Directory of Open Access Journals (Sweden)

Guohai Liu

2014-01-01

Full Text Available A fault-tolerant permanent-magnet vernier (FT-PMV machine is designed for direct-drive applications, incorporating the merits of high torque density and high reliability. Based on the so-called magnetic gearing effect, PMV machines have the ability of high torque density by introducing the flux-modulation poles (FMPs. This paper investigates the fault-tolerant characteristic of PMV machines and provides a design method, which is able to not only meet the fault-tolerant requirements but also keep the ability of high torque density. The operation principle of the proposed machine has been analyzed. The design process and optimization are presented specifically, such as the combination of slots and poles, the winding distribution, and the dimensions of PMs and teeth. By using the time-stepping finite element method (TS-FEM, the machine performances are evaluated. Finally, the FT-PMV machine is manufactured, and the experimental results are presented to validate the theoretical analysis.

Remote maintenance design for Fusion Experimental Reactor (FER)

International Nuclear Information System (INIS)

Tachikawa, K.; Iida, H.; Nishio, S.; Tone, T.; Aota, T.; Iwamoto, T.; Niikura, S.; Nishizawa, H.

1984-01-01

Design of Fusion Experimental Reactor, FER, has been conducted by Japan Atomic Energy Research Institute (JAERI) since 1981. Two typical reactors can be classified in general from the viewpoints of remote maintenance among four design concepts of FER. In the case of the type 1 FER, the torus module consists of shield structure and blanket, and the connective joints between toruses provided at the outer region of the reactor. As for the type 2 FER, the shield structure is joined with the vacuum cryostat, and only the blanket module is allowed to move, but connection between toruses are located in the inner region of the reactor. Comparing type 1 with type 2 FER, this paper describes on the remote maintenance of FER including reactor configurations, work procedures, remote systems/equipments, repairing facility and future R and D problems. Reviewing design studies and investigation for the existing robotics technologies, R and D for FER remote maintenance technology should be performed under the reasonable long-term program. The main items of remote technology required to start urgently are multi-purpose manipulator system with performance of dextrousity, tele-viewing system which reduces operator fatigue and remote tests for commercially available components

Sodium fires. Progress achieved in research and experimental results

International Nuclear Information System (INIS)

Malet, J.C.; Duverger de Cuy, G.; Casselman, C.; Charpenel, J.; Natta, M.; Devillers, C.

1979-08-01

This paper describes the sodium fire programs undertaken by the CEA's Nuclear Safety Department. Experimental results concerning sodium ignition and combustion, sodium fire suppression, sodium aerosol filtration and sodium-concrete contact reactions are given and the applications of these results in the Super-Phenix reactor is discussed

Alkali Metal Backup Cooling for Stirling Systems - Experimental Results

Science.gov (United States)

Schwendeman, Carl; Tarau, Calin; Anderson, William G.; Cornell, Peggy A.

2013-01-01

In a Stirling Radioisotope Power System (RPS), heat must be continuously removed from the General Purpose Heat Source (GPHS) modules to maintain the modules and surrounding insulation at acceptable temperatures. The Stirling convertor normally provides this cooling. If the Stirling convertor stops in the current system, the insulation is designed to spoil, preventing damage to the GPHS at the cost of an early termination of the mission. An alkali-metal Variable Conductance Heat Pipe (VCHP) can be used to passively allow multiple stops and restarts of the Stirling convertor. In a previous NASA SBIR Program, Advanced Cooling Technologies, Inc. (ACT) developed a series of sodium VCHPs as backup cooling systems for Stirling RPS. The operation of these VCHPs was demonstrated using Stirling heater head simulators and GPHS simulators. In the most recent effort, a sodium VCHP with a stainless steel envelope was designed, fabricated and tested at NASA Glenn Research Center (GRC) with a Stirling convertor for two concepts; one for the Advanced Stirling Radioisotope Generator (ASRG) back up cooling system and one for the Long-lived Venus Lander thermal management system. The VCHP is designed to activate and remove heat from the stopped convertor at a 19 degC temperature increase from the nominal vapor temperature. The 19 degC temperature increase from nominal is low enough to avoid risking standard ASRG operation and spoiling of the Multi-Layer Insulation (MLI). In addition, the same backup cooling system can be applied to the Stirling convertor used for the refrigeration system of the Long-lived Venus Lander. The VCHP will allow the refrigeration system to: 1) rest during transit at a lower temperature than nominal; 2) pre-cool the modules to an even lower temperature before the entry in Venus atmosphere; 3) work at nominal temperature on Venus surface; 4) briefly stop multiple times on the Venus surface to allow scientific measurements. This paper presents the experimental

Issues and recent advances in optimal experimental design for site investigation (Invited)

Science.gov (United States)

Nowak, W.

2013-12-01

This presentation provides an overview over issues and recent advances in model-based experimental design for site exploration. The addressed issues and advances are (1) how to provide an adequate envelope to prior uncertainty, (2) how to define the information needs in a task-oriented manner, (3) how to measure the expected impact of a data set that it not yet available but only planned to be collected, and (4) how to perform best the optimization of the data collection plan. Among other shortcomings of the state-of-the-art, it is identified that there is a lack of demonstrator studies where exploration schemes based on expert judgment are compared to exploration schemes obtained by optimal experimental design. Such studies will be necessary do address the often voiced concern that experimental design is an academic exercise with little improvement potential over the well- trained gut feeling of field experts. When addressing this concern, a specific focus has to be given to uncertainty in model structure, parameterizations and parameter values, and to related surprises that data often bring about in field studies, but never in synthetic-data based studies. The background of this concern is that, initially, conceptual uncertainty may be so large that surprises are the rule rather than the exception. In such situations, field experts have a large body of experience in handling the surprises, and expert judgment may be good enough compared to meticulous optimization based on a model that is about to be falsified by the incoming data. In order to meet surprises accordingly and adapt to them, there needs to be a sufficient representation of conceptual uncertainty within the models used. Also, it is useless to optimize an entire design under this initial range of uncertainty. Thus, the goal setting of the optimization should include the objective to reduce conceptual uncertainty. A possible way out is to upgrade experimental design theory towards real-time interaction

Empirical evidence of bias in the design of experimental stroke studies - A metaepidemiologic approach

NARCIS (Netherlands)

Crossley, Nicolas A.; Sena, Emily; Goehler, Jos; Horn, Jannekke; van der Worp, Bart; Bath, Philip M. W.; Macleod, Malcolm; Dirnagl, Ulrich

2008-01-01

Background and Purpose - At least part of the failure in the transition from experimental to clinical studies in stroke has been attributed to the imprecision introduced by problems in the design of experimental stroke studies. Using a metaepidemiologic approach, we addressed the effect of

Optimal experimental design in an epidermal growth factor receptor signalling and down-regulation model.

Science.gov (United States)

Casey, F P; Baird, D; Feng, Q; Gutenkunst, R N; Waterfall, J J; Myers, C R; Brown, K S; Cerione, R A; Sethna, J P

2007-05-01

We apply the methods of optimal experimental design to a differential equation model for epidermal growth factor receptor signalling, trafficking and down-regulation. The model incorporates the role of a recently discovered protein complex made up of the E3 ubiquitin ligase, Cbl, the guanine exchange factor (GEF), Cool-1 (beta -Pix) and the Rho family G protein Cdc42. The complex has been suggested to be important in disrupting receptor down-regulation. We demonstrate that the model interactions can accurately reproduce the experimental observations, that they can be used to make predictions with accompanying uncertainties, and that we can apply ideas of optimal experimental design to suggest new experiments that reduce the uncertainty on unmeasurable components of the system.

Experimental results obtained with the simulated cold moderator system. System characteristics and technical issues

CERN Document Server

Aso, T; Hino, R; Kaminaga, M; Kinoshita, H; Takahashi, T

2002-01-01

The Japan Atomic Energy Research Institute and the High Energy Accelerator Research Organization have been developing a Mega-Watt scale spallation target system. In the system, neutrons generated in a target are sorted out their energy to the proper values in liquid-hydrogen moderators. Then, the liquid-hydrogen is forced to circulate in order to suppress hydrogen temperature increase. In the operation of moderators, it is very important to establish a safety protection system against emergency shutdown of the accelerator or accidents of the cold moderator system. In order to obtain a technical data for design and safety review of the liquid-hydrogen system, we have fabricated an experimental apparatus simulated the cold moderator system using liquid nitrogen (max. 1.5 MPa, mini. 77 K) instead of liquid hydrogen. The experiments on a controllability of the system were carried out to investigate dynamic characteristics of the system. This report presents the experimental results and technical issues for the co...

Experimental results of the SMART ECC injection performance with reduced scale of test facility

Energy Technology Data Exchange (ETDEWEB)

Cho, Young Il; Cho, Seok; Ko, Yung Joo; Shin, Yong Cheol; Kwon, Tae Soon [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2011-05-15

SMART pressurized water reactor type is different from the existing integral NSSS commercial pressurized water reactor system which is equipped with the main features. In addition, RCS piping is removed and the feature of the SBLOCA is a major design break accident. SWAT (SMART ECC Water Asymmetric Two-phase choking test facility) test facility is to simulate the 2 inch SBLOCA of the SMART using with reduced scale. The Test was performed to produce experimental data for the validation of the TASS/SMR-S thermal hydraulic analysis code, and to investigate the related thermal hydraulic phenomena in the down-comer region during the 2 inch SBLOCA of the safety inject line. The particular phenomena for the observation are ECC bypass and multi-dimensional flow characteristics to verify the effectiveness and performance of the safety injection system. In this paper, the corresponding steady state test conditions, including initial and boundary conditions along with major measuring parameters, and related experimental results were described

Analysis and presentation of experimental results with examples, problems and programs

CERN Document Server

Christodoulides, Costas

2017-01-01

This book is intended as a guide to the analysis and presentation of experimental results. It develops various techniques for the numerical processing of experimental data, using basic statistical methods and the theory of errors. After presenting basic theoretical concepts, the book describes the methods by which the results can be presented, both numerically and graphically. The book is divided into three parts, of roughly equal length, addressing the theory, the analysis of data, and the presentation of results. Examples are given and problems are solved using the Excel, Origin, Python and R software packages. In addition, programs in all four languages are made available to readers, allowing them to use them in analyzing and presenting the results of their own experiments. Subjects are treated at a level appropriate for undergraduate students in the natural sciences, but this book should also appeal to anyone whose work involves dealing with experimental results.

Experimental system design for the integration of trapped-ion and superconducting qubit systems

Science.gov (United States)

De Motte, D.; Grounds, A. R.; Rehák, M.; Rodriguez Blanco, A.; Lekitsch, B.; Giri, G. S.; Neilinger, P.; Oelsner, G.; Il'ichev, E.; Grajcar, M.; Hensinger, W. K.

2016-12-01

We present a design for the experimental integration of ion trapping and superconducting qubit systems as a step towards the realization of a quantum hybrid system. The scheme addresses two key difficulties in realizing such a system: a combined microfabricated ion trap and superconducting qubit architecture, and the experimental infrastructure to facilitate both technologies. Developing upon work by Kielpinski et al. (Phys Rev Lett 108(13):130504, 2012. doi: 10.1103/PhysRevLett.108.130504), we describe the design, simulation and fabrication process for a microfabricated ion trap capable of coupling an ion to a superconducting microwave LC circuit with a coupling strength in the tens of kHz. We also describe existing difficulties in combining the experimental infrastructure of an ion trapping set-up into a dilution refrigerator with superconducting qubits and present solutions that can be immediately implemented using current technology.

Fundamental criteria for the design of high-performance Josephson nondestructive readout random access memory cells and experimental confirmation

International Nuclear Information System (INIS)

Henkels, W.H.

1979-01-01

Fundamental design criteria for Josephson nondestructive readout random access memory (NDRO RAM) cells are presented, within the context of an LSI array environment. Emphasis is placed upon principles which are relevant to high performance. The criteria are elucidated via a specific design which is simulated and then experimentally evaluated in a technology with a smallest critical dimension of 5 μm. The specific cell differs from previously tested Josephson NDRO cells in several respects; namely, the cell stores only approx.8Phi 0 , employs interferometer gates and an external damping resistor, allows switching into device resonances, and eliminates the need for a special initialization cycle. The cell-selection scheme, employing triple coincidence, results in larger operating margins and smaller operating currents than have previously been achieved. The large operating margins and all basic cell design criteria were experimentally verified. The experimental interferometer gate characteristics were analyzed in detail and found to be describable by simple models. In addition, it was discovered that single flux quantum transitions in the interferometer gates could be exploited beneficially in order to enhance the insensitivity of operating margins to fabrication tolerances

Experimental design for reflection measurements of highly reactive liquid or solid substances with application to liquid sodium

International Nuclear Information System (INIS)

Chan, S.H.; Gossler, A.A.

1980-01-01

A versatile goniometer system with associated electronic components and mechanical instruments has been assembled. It is designed to measure spectral, specular reflectances of highly reactive liquid or solid substances over a spectral range of 0.3 to 9 μ and incidence angles of 12 to 30 0 off the normal direction. The capability of measuring reflectances of liquid substances clearly distinguishes this experimental design from conventional systems which are applicable only to solid substances. This design has been used to measure the spectral, specular reflectance of liquid sodium and preliminary results obtained are compared with those of solid sodium measured by other investigators

DoSSiER: Database of Scientific Simulation and Experimental Results

CERN Document Server

Wenzel, Hans; Genser, Krzysztof; Elvira, Daniel; Pokorski, Witold; Carminati, Federico; Konstantinov, Dmitri; Ribon, Alberto; Folger, Gunter; Dotti, Andrea

2017-01-01

The Geant4, GeantV and GENIE collaborations regularly perform validation and regression tests for simulation results. DoSSiER (Database of Scientific Simulation and Experimental Results) is being developed as a central repository to store the simulation results as well as the experimental data used for validation. DoSSiER can be easily accessed via a web application. In addition, a web service allows for programmatic access to the repository to extract records in json or xml exchange formats. In this article, we describe the functionality and the current status of various components of DoSSiER as well as the technology choices we made.

Combined application of mixture experimental design and artificial neural networks in the solid dispersion development.

Science.gov (United States)

Medarević, Djordje P; Kleinebudde, Peter; Djuriš, Jelena; Djurić, Zorica; Ibrić, Svetlana

2016-01-01

This study for the first time demonstrates combined application of mixture experimental design and artificial neural networks (ANNs) in the solid dispersions (SDs) development. Ternary carbamazepine-Soluplus®-poloxamer 188 SDs were prepared by solvent casting method to improve carbamazepine dissolution rate. The influence of the composition of prepared SDs on carbamazepine dissolution rate was evaluated using d-optimal mixture experimental design and multilayer perceptron ANNs. Physicochemical characterization proved the presence of the most stable carbamazepine polymorph III within the SD matrix. Ternary carbamazepine-Soluplus®-poloxamer 188 SDs significantly improved carbamazepine dissolution rate compared to pure drug. Models developed by ANNs and mixture experimental design well described the relationship between proportions of SD components and percentage of carbamazepine released after 10 (Q10) and 20 (Q20) min, wherein ANN model exhibit better predictability on test data set. Proportions of carbamazepine and poloxamer 188 exhibited the highest influence on carbamazepine release rate. The highest carbamazepine release rate was observed for SDs with the lowest proportions of carbamazepine and the highest proportions of poloxamer 188. ANNs and mixture experimental design can be used as powerful data modeling tools in the systematic development of SDs. Taking into account advantages and disadvantages of both techniques, their combined application should be encouraged.

Experimental and Sampling Design for the INL-2 Sample Collection Operational Test

Energy Technology Data Exchange (ETDEWEB)

Piepel, Gregory F.; Amidan, Brett G.; Matzke, Brett D.

2009-02-16

This report describes the experimental and sampling design developed to assess sampling approaches and methods for detecting contamination in a building and clearing the building for use after decontamination. An Idaho National Laboratory (INL) building will be contaminated with BG (Bacillus globigii, renamed Bacillus atrophaeus), a simulant for Bacillus anthracis (BA). The contamination, sampling, decontamination, and re-sampling will occur per the experimental and sampling design. This INL-2 Sample Collection Operational Test is being planned by the Validated Sampling Plan Working Group (VSPWG). The primary objectives are: 1) Evaluate judgmental and probabilistic sampling for characterization as well as probabilistic and combined (judgment and probabilistic) sampling approaches for clearance, 2) Conduct these evaluations for gradient contamination (from low or moderate down to absent or undetectable) for different initial concentrations of the contaminant, 3) Explore judgment composite sampling approaches to reduce sample numbers, 4) Collect baseline data to serve as an indication of the actual levels of contamination in the tests. A combined judgmental and random (CJR) approach uses Bayesian methodology to combine judgmental and probabilistic samples to make clearance statements of the form "X% confidence that at least Y% of an area does not contain detectable contamination” (X%/Y% clearance statements). The INL-2 experimental design has five test events, which 1) vary the floor of the INL building on which the contaminant will be released, 2) provide for varying the amount of contaminant released to obtain desired concentration gradients, and 3) investigate overt as well as covert release of contaminants. Desirable contaminant gradients would have moderate to low concentrations of contaminant in rooms near the release point, with concentrations down to zero in other rooms. Such gradients would provide a range of contamination levels to challenge the sampling

COMPUTER-AIDED DESIGN, MANUFACTURE AND EXPERIMENTAL ANALYSIS OF A PAIR OF ELLIPTICAL SPUR GEARS

Directory of Open Access Journals (Sweden)

Mehmet YAZAR

2016-12-01

Full Text Available ABSTRACT In this study, geometrical equations of elliptical spur gears, which are too difficult to manufacture by traditional methods and which require specific machines equipped with special techniques, are developed using the methods in the literature. Using these equations, a LISP program on AutoLISP is created to model elliptical spur gears on AutoCAD with desired tooth number and modules. Elliptical spur gears are manufactured with 5 different modules by Wire EDM through the above-mentioned package program. The variations in the center distances of elliptical spur gears, the most important parameter for workability of gears, are experimentally determined by a simple test unit designed and manufactured within the context this study. In addition, the surface roughness and hardness of elliptical spur gears are obtained and hydraulic pump and noise analysis results are discussed. The experimental and computer-aided results show that the elliptical spur gears may widely be used in many industrial and mechanical applications in the future.

Experimental design and data-analysis in label-free quantitative LC/MS proteomics: A tutorial with MSqRob.

Science.gov (United States)

Goeminne, Ludger J E; Gevaert, Kris; Clement, Lieven

2018-01-16

Label-free shotgun proteomics is routinely used to assess proteomes. However, extracting relevant information from the massive amounts of generated data remains difficult. This tutorial provides a strong foundation on analysis of quantitative proteomics data. We provide key statistical concepts that help researchers to design proteomics experiments and we showcase how to analyze quantitative proteomics data using our recent free and open-source R package MSqRob, which was developed to implement the peptide-level robust ridge regression method for relative protein quantification described by Goeminne et al. MSqRob can handle virtually any experimental proteomics design and outputs proteins ordered by statistical significance. Moreover, its graphical user interface and interactive diagnostic plots provide easy inspection and also detection of anomalies in the data and flaws in the data analysis, allowing deeper assessment of the validity of results and a critical review of the experimental design. Our tutorial discusses interactive preprocessing, data analysis and visualization of label-free MS-based quantitative proteomics experiments with simple and more complex designs. We provide well-documented scripts to run analyses in bash mode on GitHub, enabling the integration of MSqRob in automated pipelines on cluster environments (https://github.com/statOmics/MSqRob). The concepts outlined in this tutorial aid in designing better experiments and analyzing the resulting data more appropriately. The two case studies using the MSqRob graphical user interface will contribute to a wider adaptation of advanced peptide-based models, resulting in higher quality data analysis workflows and more reproducible results in the proteomics community. We also provide well-documented scripts for experienced users that aim at automating MSqRob on cluster environments. Copyright © 2017 Elsevier B.V. All rights reserved.

Optimization of single-walled carbon nanotube solubility by noncovalent PEGylation using experimental design methods

Directory of Open Access Journals (Sweden)

Hadidi N

2011-04-01

Full Text Available Naghmeh Hadidi1, Farzad Kobarfard2, Nastaran Nafissi-Varcheh3, Reza Aboofazeli11Department of Pharmaceutics, 2Department of Pharmaceutical Chemistry, 3Department of Pharmaceutical Biotechnology, School of Pharmacy, Shaheed Beheshti University of Medical Sciences, Tehran, IranAbstract: In this study, noncovalent functionalization of single-walled carbon nanotubes (SWCNTs with phospholipid-polyethylene glycols (Pl-PEGs was performed to improve the solubility of SWCNTs in aqueous solution. Two kinds of PEG derivatives, ie, Pl-PEG 2000 and Pl-PEG 5000, were used for the PEGylation process. An experimental design technique (D-optimal design and second-order polynomial equations was applied to investigate the effect of variables on PEGylation and the solubility of SWCNTs. The type of PEG derivative was selected as a qualitative parameter, and the PEG/SWCNT weight ratio and sonication time were applied as quantitative variables for the experimental design. Optimization was performed for two responses, aqueous solubility and loading efficiency. The grafting of PEG to the carbon nanostructure was determined by thermogravimetric analysis, Raman spectroscopy, and scanning electron microscopy. Aqueous solubility and loading efficiency were determined by ultraviolet-visible spectrophotometry and measurement of free amine groups, respectively. Results showed that Pl-PEGs were grafted onto SWCNTs. Aqueous solubility of 0.84 mg/mL and loading efficiency of nearly 98% were achieved for the prepared Pl-PEG 5000-SWCNT conjugates. Evaluation of functionalized SWCNTs showed that our noncovalent functionalization protocol could considerably increase aqueous solubility, which is an essential criterion in the design of a carbon nanotube-based drug delivery system and its biodistribution.Keywords: phospholipid-PEG, D-optimal design, loading efficiency, Raman spectroscopy, scanning electron microscopy, theromogravimetric analysis, carbon nanotubes

design and experimental study of a solar system for heating water ...

African Journals Online (AJOL)

M. Ghodbane, B. Boumeddane, N. Said

2016-09-01

Sep 1, 2016 ... This work presents a design and an experimental study of a linear Fresnel reflector solar with trapezoidal cavity. ... concentrator in the solar fields allocated to the domestics and industrial water-heaters. Keywords: ...... integrated photovoltaic panels, Journal of Solar Energy Engineering, Transactions of the ...

Bayesian optimal experimental design for priors of compact support

KAUST Repository

Long, Quan

2016-01-08

In this study, we optimize the experimental setup computationally by optimal experimental design (OED) in a Bayesian framework. We approximate the posterior probability density functions (pdf) using truncated Gaussian distributions in order to account for the bounded domain of the uniform prior pdf of the parameters. The underlying Gaussian distribution is obtained in the spirit of the Laplace method, more precisely, the mode is chosen as the maximum a posteriori (MAP) estimate, and the covariance is chosen as the negative inverse of the Hessian of the misfit function at the MAP estimate. The model related entities are obtained from a polynomial surrogate. The optimality, quantified by the information gain measures, can be estimated efficiently by a rejection sampling algorithm against the underlying Gaussian probability distribution, rather than against the true posterior. This approach offers a significant error reduction when the magnitude of the invariants of the posterior covariance are comparable to the size of the bounded domain of the prior. We demonstrate the accuracy and superior computational efficiency of our method for shock-tube experiments aiming to measure the model parameters of a key reaction which is part of the complex kinetic network describing the hydrocarbon oxidation. In the experiments, the initial temperature and fuel concentration are optimized with respect to the expected information gain in the estimation of the parameters of the target reaction rate. We show that the expected information gain surface can change its shape dramatically according to the level of noise introduced into the synthetic data. The information that can be extracted from the data saturates as a logarithmic function of the number of experiments, and few experiments are needed when they are conducted at the optimal experimental design conditions.

An innovative magnetorheological damper for automotive suspension: from design to experimental characterization

Science.gov (United States)

Sassi, Sadok; Cherif, Khaled; Mezghani, Lotfi; Thomas, Marc; Kotrane, Asma

2005-08-01

The development of a powerful new magnetorheological fluid (MRF), together with recent progress in the understanding of the behavior of such fluids, has convinced researchers and engineers that MRF dampers are among the most promising devices for semi-active automotive suspension vibration control, because of their large force capacity and their inherent ability to provide a simple, fast and robust interface between electronic controls and mechanical components. In this paper, theoretical and experimental studies are performed for the design, development and testing of a completely new MRF damper model that can be used for the semi-active control of automotive suspensions. The MR damper technology presented in this paper is based on a completely new approach where, in contrast to in the conventional solutions where the coil axis is usually superposed on the damper axis and where the inner cylindrical housing is part of the magnetic circuit, the coils are wound in a direction perpendicular to the damper axis. The paper investigates approaches to optimizing the dynamic response and provides experimental verification. Both experimental and theoretical results have shown that, if this particular model is filled with an 'MRF 336AG' MR fluid, it can provide large controllable damping forces that require only a small amount of energy. For a magnetizing system with four coils, the damping coefficient could be increased by up to three times for an excitation current of only 2 A. Such current could be reduced to less than 1 A if the magnetizing system used eight small cores. In this case, the magnetic field will be more powerful and more regularly distributed. In the presence of harmonic excitation, such a design will allow the optimum compromise between comfort and stability to be reached over different intervals of the excitation frequencies.

Optimization and evaluation of clarithromycin floating tablets using experimental mixture design.

Science.gov (United States)

Uğurlu, Timucin; Karaçiçek, Uğur; Rayaman, Erkan

2014-01-01

The purpose of the study was to prepare and evaluate clarithromycin (CLA) floating tablets using experimental mixture design for treatment of Helicobacter pylori provided by prolonged gastric residence time and controlled plasma level. Ten different formulations were generated based on different molecular weight of hypromellose (HPMC K100, K4M, K15M) by using simplex lattice design (a sub-class of mixture design) with Minitab 16 software. Sodium bicarbonate and anhydrous citric acid were used as gas generating agents. Tablets were prepared by wet granulation technique. All of the process variables were fixed. Results of cumulative drug release at 8th h (CDR 8th) were statistically analyzed to get optimized formulation (OF). Optimized formulation, which gave floating lag time lower than 15 s and total floating time more than 10 h, was analyzed and compared with target for CDR 8th (80%). A good agreement was shown between predicted and actual values of CDR 8th with a variation lower than 1%. The activity of clarithromycin contained optimizedformula against H. pylori were quantified using well diffusion agar assay. Diameters of inhibition zones vs. log10 clarithromycin concentrations were plotted in order to obtain a standard curve and clarithromycin activity.

ENGINEERING DESIGN OPTIMIZATION OF HEEL TESTING EQUIPMENT IN THE EXPERIMENTAL VALIDATION OF SAFE WALKING

Directory of Open Access Journals (Sweden)

Cristiano Fragassa

2017-06-01

Full Text Available Experimental test methods for the evaluation of the resistance of heels of ladies' shoes in the case of impact loads are fully defined by International Organization for Standardization (ISO procedures that indicate all the conditions of experiment. A first Standard (ISO 19553 specifies the test method for determining the strength of the heels in the case of single impact. The result offers a valuation of the liability to fail under the sporadic heavy blows. A second Standard (ISO 19556 details a method for testing the capability of heels of women' shoes to survive to the repetition of small impacts provoked by normal walking. These Standards strictly define the features for two different testing devices (with specific materials, geometries, weights, etc. and all the experimental procedures to be followed during tests. On the contrary, this paper describes the technical solutions adopted to design one single experimental device able to perform impact testing of heels in both conditions. Joining the accuracy of mechanic movements with the speed of an electronic control system, a new and flexible equipment for the complete characterization of heels respect to (single or fatigue impacts was developed. Moreover a new level of performances in experimental validation of heel resistance was introduced by the versatility of the user-defined software control programs, able to encode every complex time-depending cycle of impact loads. Dynamic simulations permitted to investigate the impacts on heel in different conditions of testing, optimizing the machine design. The complexity of real stresses on shoes during an ordinary walk and in other common situations (as going up and downstairs was considered for a proper dimensioning.

A survey of Wien bridge-based chaotic oscillators: Design and experimental issues

Energy Technology Data Exchange (ETDEWEB)

Kilic, Recai [Erciyes University, Department of Electrical and Electronic Engineering, 38039 Kayseri (Turkey)], E-mail: kilic@erciyes.edu.tr; Yildirim, Fatma [Erciyes University, Civil Aviation School, 38039 Kayseri (Turkey)

2008-12-15

This paper presents a comparative study on design and implementation of Wien type chaotic oscillators. By making a collection of almost all Wien bridge-based chaotic circuits, we have investigated these oscillators in terms of chaotic dynamics, circuit structures, active building blocks, nonlinear element structures and operating frequency by using PSpice simulations and laboratory experiments. In addition to this comparative investigation, we present our two basic experimental contributions to referred implementations. While the first of our experimental contributions consists of the experimentally implementation of CFOA-based Chua's circuit modified for very high chaotic oscillations, the scope of the second is to experimentally implement a Wien type high frequency chaos generator, which has the diode-inductor composite, in the inductorless form by using CFOA-based synthetic inductor.

Using a Discussion about Scientific Controversy to Teach Central Concepts in Experimental Design

Science.gov (United States)

Bennett, Kimberley Ann

2015-01-01

Students may need explicit training in informal statistical reasoning in order to design experiments or use formal statistical tests effectively. By using scientific scandals and media misinterpretation, we can explore the need for good experimental design in an informal way. This article describes the use of a paper that reviews the measles mumps…

Comparing the effects of community service and imprisonment on reconviction: results from a quasi-experimental Danish study

DEFF Research Database (Denmark)

Klement, Christian

2015-01-01

Objective This study compares reconviction rates for Danish offenders sentenced to community service and imprisonment. A large general sample of offenders (n = 1602) is examined. Methods The study relies on a quasi-experimental design and uses propensity score matching as well as logistic....... Results Imprisonment is associated with a higher rate of recidivism and the result is statistically significant at conventional statistical levels. Conclusions Community service (CS) compared to imprisonment appears to cause a lower reconviction rate in general. Additional research is needed to shed light...

Coal Recycling from Tailings using Flotation with 2-Level Experimental Design Techniques

Directory of Open Access Journals (Sweden)

Sajjad Jannesar Malakooti

2012-12-01

Full Text Available In this study, the possibility of producing coal with less than 11% ash from tailings of flotation process was investigated. The effect of six flotation parameters: collector type, collector consumption, frother type, frother consumption, pulp density and mixing rate were studied on a sample from a tailing dam. A software based experimental design approach (DX7 was applied to determine and model effective parameters as well as flotation optimization through fractional factorial. It was shown that collector type and flotation machine mixing rate were the most effective parameters on ash content of concentrate. The results indicated that the production of a desired ash content concentrate, i.e.

Characterization of an extrapolation chamber for low-energy X-rays: Experimental and Monte Carlo preliminary results

Energy Technology Data Exchange (ETDEWEB)

Neves, Lucio P., E-mail: lpneves@ipen.br [Instituto de Pesquisas Energeticas e Nucleares (IPEN-CNEN), Comissao Nacional de Energia Nuclear, Av. Prof. Lineu Prestes 2242, 05508-000 Sao Paulo, SP (Brazil); Silva, Eric A.B., E-mail: ebrito@usp.br [Instituto de Pesquisas Energeticas e Nucleares (IPEN-CNEN), Comissao Nacional de Energia Nuclear, Av. Prof. Lineu Prestes 2242, 05508-000 Sao Paulo, SP (Brazil); Perini, Ana P., E-mail: aperini@ipen.br [Instituto de Pesquisas Energeticas e Nucleares (IPEN-CNEN), Comissao Nacional de Energia Nuclear, Av. Prof. Lineu Prestes 2242, 05508-000 Sao Paulo, SP (Brazil); Maidana, Nora L., E-mail: nmaidana@if.usp.br [Universidade de Sao Paulo, Instituto de Fisica, Travessa R 187, 05508-900 Sao Paulo, SP (Brazil); Caldas, Linda V.E., E-mail: lcaldas@ipen.br [Instituto de Pesquisas Energeticas e Nucleares (IPEN-CNEN), Comissao Nacional de Energia Nuclear, Av. Prof. Lineu Prestes 2242, 05508-000 Sao Paulo, SP (Brazil)

2012-07-15

The extrapolation chamber is a parallel-plate ionization chamber that allows variation of its air-cavity volume. In this work, an experimental study and MCNP-4C Monte Carlo code simulations of an ionization chamber designed and constructed at the Calibration Laboratory at IPEN to be used as a secondary dosimetry standard for low-energy X-rays are reported. The results obtained were within the international recommendations, and the simulations showed that the components of the extrapolation chamber may influence its response up to 11.0%. - Highlights: Black-Right-Pointing-Pointer A homemade extrapolation chamber was studied experimentally and with Monte Carlo. Black-Right-Pointing-Pointer It was characterized as a secondary dosimetry standard, for low energy X-rays. Black-Right-Pointing-Pointer Several characterization tests were performed and the results were satisfactory. Black-Right-Pointing-Pointer Simulation showed that its components may influence the response up to 11.0%. Black-Right-Pointing-Pointer This chamber may be used as a secondary standard at our laboratory.

Evaluation of thermal ratchetting on axisymmetric thin shells at the free level of sodium: Experimental results and elastic analysis

International Nuclear Information System (INIS)

Cabrillat, M.T.; Gatt, J.M.; Schoulguine, P.; Skiara, A.

1993-01-01

Startup operations and load variations for a FBR reactor (Fast Breeder Reactor) cause sodium level variations in the vessels which exert stresses on the emergent shells in the free level area. The loading of these shells is mainly linked to the axial thermal gradient, primary stresses being generally low or negligible as are the radial thermal gradients. Under the effect of these variable axial thermal gradients, there is a risk of progressive deformation even in the absence of primary type stresses. The simplified methods of analysis (Bree diagram, efficiency diagram) proposed in the design codes (Code Case and RCCMR) are not applicable in this specific case where primary type stresses are negligible. In recent years, many studies and experimental programmes have been undertaken in order to propose more reliable methods of analysis for these structures. This paper describes the experimental program, called VINIL, developed at the CEA at Cadarache. After a brief description of the experimental facility and of the experimental results, this paper proposes an evaluation of the risk of progressive deformation on an elastic basis: various simplified methods of analysis were used and are compared with experimental results

modelling of directed evolution: Implications for experimental design and stepwise evolution

OpenAIRE

Wedge , David C.; Rowe , William; Kell , Douglas B.; Knowles , Joshua

2009-01-01

In silico modelling of directed evolution: Implications for experimental design and stepwise evolution correspondence: Corresponding author. Tel.: +441613065145. (Wedge, David C.) (Wedge, David C.) Manchester Interdisciplinary Biocentre, University of Manchester - 131 Princess Street--> , Manchester--> , M1 7ND--> - UNITED KINGDOM (Wedge, David C.) UNITED KINGDOM (Wedge, David C.) Man...

Delineamento experimental e tamanho de amostra para alface cultivada em hidroponia Experimental design and sample size for hydroponic lettuce crop

Directory of Open Access Journals (Sweden)

Valéria Schimitz Marodim

2000-10-01

Full Text Available Este estudo visa a estabelecer o delineamento experimental e o tamanho de amostra para a cultura da alface (Lactuca sativa em hidroponia, pelo sistema NFT (Nutrient film technique. O experimento foi conduzido no Laboratório de Cultivos Sem Solo/Hidroponia, no Departamento de Fitotecnia da Universidade Federal de Santa Maria e baseou-se em dados de massa de plantas. Os resultados obtidos mostraram que, usando estrutura de cultivo de alface em hidroponia sobre bancadas de fibrocimento com seis canais, o delineamento experimental adequado é blocos ao acaso se a unidade experimental for constituída de faixas transversais aos canais das bancadas, e deve ser inteiramente casualizado se a bancada for a unidade experimental; para a variável massa de plantas, o tamanho da amostra é de 40 plantas para uma semi-amplitude do intervalo de confiança em percentagem da média (d igual a 5% e de 7 plantas para um d igual a 20%.This study was carried out to establish the experimental design and sample size for hydroponic lettuce (Lactuca sativa crop under nutrient film technique. The experiment was conducted in the Laboratory of Hydroponic Crops of the Horticulture Department of the Federal University of Santa Maria. The evaluated traits were plant weight. Under hydroponic conditions on concrete bench with six ducts, the most indicated experimental design for lettuce is randomised blocks for duct transversal plots or completely randomised for bench plot. The sample size for plant weight should be 40 and 7 plants, respectively, for a confidence interval of mean percentage (d equal to 5% and 20%.

Experimental results and analysis on hydrogen combustion

International Nuclear Information System (INIS)

Dorofeev, S.B.; Efimenko, A.A.; Kochurko, A.S.; Sidorov, V.P.; Bezmelnitsin, A.V.

1994-01-01

The Small-Scale Development Apparatus (SSDA) was constructed to provide a preliminary set of experimental data to characterize the effect of temperature on the ability of hydrogen-air-steam-mixtures to undergo detonations and, equally important, to support design of the larger-scale High-Temperature Combustion Facility (HTCF) by providing a test bed for solution of a number of high-temperature design and operational problems. The SSDA, the central element of which is 10-cm inside diameter, 6.1-m long tubular test vessel designed to permit detonation experiments at temperatures up to 700K, was employed to study self-sustained detonations in gaseous mixtures of hydrogen, air, and steam at temperature between 300K and 650K at a fixed pressure of 0.1 MPa. Detonation cell size measurements provide clear evidence that the effect of hydrogen-air gas mixture temperature, in the range 300K to 650K, is to decrease cell size and, hence, to increase the sensitivity of the mixture to undergo detonations. The effect of steam content, at any given temperature, is to increase the cell size and, thereby, to decrease the sensitivity of stoichiometric hydrogen-air mixtures. The one-dimensional ZND model does a very good job at predicting the overall trends in the cell size data over the range of hydrogen-air-steam mixture compositions and temperature studied in the experiments. Experiments were conducted to measure the rate of hydrogen oxidation in the absence of ignition sources at temperatures of 500K and 650K, for hydrogen-air mixtures of 15% and 50%, and for a mixture of equimolar hydrogen-air and 30% steam at 650K. The rate of hydrogen oxidation was found to be significant at 650K. Reduction of hydrogen concentration by chemical reaction from 50 to 44% hydrogen, and from 15 to 11% hydrogen, were observed on a time frame of minutes. The DeSoete rate equation predicts the 50% experiment very well, but greatly underestimates the reaction rate of the lean mixtures

Microrandomized trials: An experimental design for developing just-in-time adaptive interventions.

Science.gov (United States)

Klasnja, Predrag; Hekler, Eric B; Shiffman, Saul; Boruvka, Audrey; Almirall, Daniel; Tewari, Ambuj; Murphy, Susan A

2015-12-01

This article presents an experimental design, the microrandomized trial, developed to support optimization of just-in-time adaptive interventions (JITAIs). JITAIs are mHealth technologies that aim to deliver the right intervention components at the right times and locations to optimally support individuals' health behaviors. Microrandomized trials offer a way to optimize such interventions by enabling modeling of causal effects and time-varying effect moderation for individual intervention components within a JITAI. The article describes the microrandomized trial design, enumerates research questions that this experimental design can help answer, and provides an overview of the data analyses that can be used to assess the causal effects of studied intervention components and investigate time-varying moderation of those effects. Microrandomized trials enable causal modeling of proximal effects of the randomized intervention components and assessment of time-varying moderation of those effects. Microrandomized trials can help researchers understand whether their interventions are having intended effects, when and for whom they are effective, and what factors moderate the interventions' effects, enabling creation of more effective JITAIs. (PsycINFO Database Record (c) 2015 APA, all rights reserved).

RC Beams Strengthened with Mechanically Fastened Composites: Experimental Results and Numerical Modeling

Directory of Open Access Journals (Sweden)

Enzo Martinelli

2014-03-01

Full Text Available The use of mechanically-fastened fiber-reinforced polymer (MF-FRP systems has recently emerged as a competitive solution for the flexural strengthening of reinforced concrete (RC beams and slabs. An overview of the experimental research has proven the effectiveness and the potentiality of the MF-FRP technique which is particularly suitable for emergency repairs or when the speed of installation and immediacy of use are imperative. A finite-element (FE model has been recently developed by the authors with the aim to simulate the behavior of RC beams strengthened in bending by MF-FRP laminates; such a model has also been validated by using a wide experimental database collected from the literature. By following the previous study, the FE model and the assembled database are considered herein with the aim of better exploring the influence of some specific aspects on the structural response of MF-FRP strengthened members, such as the bearing stress-slip relationship assumed for the FRP-concrete interface, the stress-strain law considered for reinforcing steel rebars and the cracking process in RC members resulting in the well-known tension stiffening effect. The considerations drawn from this study will be useful to researchers for the calibration of criteria and design rules for strengthening RC beams through MF-FRP laminates.

Design considerations for ITER [International Thermonuclear Experimental Reactor] magnet systems: Revision 1

International Nuclear Information System (INIS)

Henning, C.D.; Miller, J.R.

1988-01-01

The International Thermonuclear Experimental Reactor (ITER) is now completing a definition phase as a beginning of a three-year design effort. Preliminary parameters for the superconducting magnet system have been established to guide further and more detailed design work. Radiation tolerance of the superconductors and insulators has been of prime importance, since it sets requirements for the neutron-shield dimension and sensitively influences reactor size. The major levels of mechanical stress in the structure appear in the cases of the inboard legs of the toroidal-field (TF) coils. The cases of the poloidal-field (PF) coils must be made thin or segmented to minimize eddy current heating during inductive plasma operation. As a result, the winding packs of both the TF and PF coils includes significant fractions of steel. The TF winding pack provides support against in-plane separating loads but offers little support against out-of-plane loads, unless shear-bonding of the conductors can be maintained. The removal of heat due to nuclear and ac loads has not been a fundamental limit to design, but certainly has non-negligible economic consequences. We present here preliminary ITER magnet systems design parameters taken from trade studies, designs, and analyses performed by the Home Teams of the four ITER participants, by the ITER Magnet Design Unit in Garching, and by other participants at workshops organized by the Magnet Design Unit. The work presented here reflects the efforts of many, but the responsibility for the opinions expressed is the authors'. 4 refs., 3 figs., 4 tabs

Efficient experimental design of high-fidelity three-qubit quantum gates via genetic programming

Science.gov (United States)

Devra, Amit; Prabhu, Prithviraj; Singh, Harpreet; Arvind; Dorai, Kavita

2018-03-01

We have designed efficient quantum circuits for the three-qubit Toffoli (controlled-controlled-NOT) and the Fredkin (controlled-SWAP) gate, optimized via genetic programming methods. The gates thus obtained were experimentally implemented on a three-qubit NMR quantum information processor, with a high fidelity. Toffoli and Fredkin gates in conjunction with the single-qubit Hadamard gates form a universal gate set for quantum computing and are an essential component of several quantum algorithms. Genetic algorithms are stochastic search algorithms based on the logic of natural selection and biological genetics and have been widely used for quantum information processing applications. We devised a new selection mechanism within the genetic algorithm framework to select individuals from a population. We call this mechanism the "Luck-Choose" mechanism and were able to achieve faster convergence to a solution using this mechanism, as compared to existing selection mechanisms. The optimization was performed under the constraint that the experimentally implemented pulses are of short duration and can be implemented with high fidelity. We demonstrate the advantage of our pulse sequences by comparing our results with existing experimental schemes and other numerical optimization methods.

Design Methodology and Experimental Verification of Serpentine/Folded Waveguide TWTs

Science.gov (United States)

2016-03-17

FW), oscillation, serpentine, stopband, traveling -wave tube (TWT), vacuum electronics. I. INTRODUCTION DEVELOPMENT of high-power broadband vacuum elec...tron devices (VEDs) beyond Ka-band using conventional coupled-cavity and helix traveling -wave tube (TWT) RF cir- cuit fabrication techniques is...bottom plot. III. G-BAND CIRCUIT DESIGN AND EXPERIMENTAL VALIDATION The primary motivation for the G-band amplifier was to develop a high-power broadband

Design and experimental verification for optical module of optical vector-matrix multiplier.

Science.gov (United States)

Zhu, Weiwei; Zhang, Lei; Lu, Yangyang; Zhou, Ping; Yang, Lin

2013-06-20

Optical computing is a new method to implement signal processing functions. The multiplication between a vector and a matrix is an important arithmetic algorithm in the signal processing domain. The optical vector-matrix multiplier (OVMM) is an optoelectronic system to carry out this operation, which consists of an electronic module and an optical module. In this paper, we propose an optical module for OVMM. To eliminate the cross talk and make full use of the optical elements, an elaborately designed structure that involves spherical lenses and cylindrical lenses is utilized in this optical system. The optical design software package ZEMAX is used to optimize the parameters and simulate the whole system. Finally, experimental data is obtained through experiments to evaluate the overall performance of the system. The results of both simulation and experiment indicate that the system constructed can implement the multiplication between a matrix with dimensions of 16 by 16 and a vector with a dimension of 16 successfully.

New insights on therapeutic touch: a discussion of experimental methodology and design that resulted in significant effects on normal human cells and osteosarcoma.

Science.gov (United States)

Monzillo, Eloise; Gronowicz, Gloria

2011-01-01

Our purpose is to discuss the study design and innovative approaches that led to finding significant effects of one energy medicine therapy, Therapeutic Touch (TT), on cells. In the original published studies, TT was shown to significantly increase human osteoblast DNA synthesis, differentiation, and mineralization; increase in a dose-dependent manner the growth of other human cell types; and decrease the differentiation and mineralization of a human osteosarcoma-derived cell line. A unique feature of the study's methodology and design that contributed to the success of the findings was that a basic level of skill and maturity of the TT practitioner was quantified for producing observable and replicable outcomes in a test administered to all TT practitioners. Only those practitioners that passed the test were selected for the study. (2) The practitioners were required to keep a journal, which appeared to promote their ability to stay centered and replicate their treatments over months of cell experimentation. (3) The origin of the cells that the practitioners were treating was explained to them, although they were blinded to cell type during the experiments. (4) Only early passage cells were used to maintain a stable cell phenotype. (5) Standard protocols for performing TT in the room were followed to ensure reproducible conditions. (6) Placebo controls and untreated controls were used for each experiment. (7) The principal investigator and technicians performing the assays were blinded as to the experimental groups, and all assays and procedures were well established in the laboratory prior to the start of the TT experiments. The absence of studies on the human biofield from mainstream scientific literature is also discussed by describing the difficulties encountered in publishing. These roadblocks contribute to our lack of understanding of the human biofield and energy medicine modalities in science. In conclusion, this report seeks to encourage well-designed

Simulation and preliminary experimental results for an active neutron counter using a neutron generator for a fissile material accounting

International Nuclear Information System (INIS)

Ahn, Seong-Kyu; Lee, Tae-Hoon; Shin, Hee-Sung; Kim, Ho-Dong

2009-01-01

An active neutron coincidence counter using a neutron generator as an interrogation source has been suggested. Because of the high energy of the interrogation neutron source, 2.5 MeV, the induced fission rate is strongly affected by the moderator design. MCNPX simulation has been performed to evaluate the performance achieved with these moderators. The side- and bottom-moderator are significantly important to thermalize neutrons to induce fission. Based on the simulation results, the moderators are designed to be adapted to the experimental system. Their preliminary performance has been tested by using natural uranium oxide powder samples. For a sample of up to 3.5 kg, which contains 21.7 g of 235 U, 2.64 cps/g- 235 U coincidence events have been measured. Mean background error was 9.57 cps and the resultant coincidence error was 13.8 cps. The experimental result shows the current status of an active counting using a neutron generator which still has some challenges to overcome. However, the controllability of an interrogation source makes this system more applicable for a variety of combinations with other non-destructive methods like a passive coincidence counting especially under a harsh environment such as a hot cell. More precise experimental setup and tests with higher enriched samples will be followed to develop a system to apply it to an active measurement for the safeguards of a spent fuel treatment process.

Experimental design and multicriteria decision making methods for the optimization of ice cream composition

Directory of Open Access Journals (Sweden)

Cristian Rojas

2012-03-01

Full Text Available The aim of the present work was to optimize the sensorial and technological features of ice cream. The experimental work was performed in two stages: 1 optimization of lactose enzymatic hydrolysis, and 2 optimization of the process and product. For the first stage a complete factorial design was developed, optimized using both response surface and the steepest ascent method. In the second stage a mixture design was performed, combining the process variables. The product with the best sensorial acceptance, high yield and low cost was selected. The acceptance of the product was developed by an untrained taster’s panel. As a main result the sensorial and technological features of the final product were improved, establishing the optimum parameters for its elaboration.

PCM-air heat exchangers for free-cooling applications in buildings: Experimental results of two real-scale prototypes

International Nuclear Information System (INIS)

Lazaro, Ana; Dolado, Pablo; Marin, Jose M.; Zalba, Belen

2009-01-01

Latent heat storage using phase change materials (PCM) can be used for free-cooling. In this application low air temperature is used to solidify the PCM during the night and then during the next day, the inside air of a building can be cooled down by exchanging heat with PCM. Short times for charging and discharging the PCM are required. PCM have in general low thermal conductivity, therefore the heat exchanger design is very important to fulfil free-cooling requirements. This paper presents an experimental setup for testing PCM-air real-scale heat exchangers and the results for two real-scale prototypes. Results show that a heat exchanger using a PCM with lower thermal conductivity and lower total stored energy, but adequately designed, has higher cooling power and can be applied for free-cooling

Online optimal experimental re-design in robotic parallel fed-batch cultivation facilities.

Science.gov (United States)

Cruz Bournazou, M N; Barz, T; Nickel, D B; Lopez Cárdenas, D C; Glauche, F; Knepper, A; Neubauer, P

2017-03-01

We present an integrated framework for the online optimal experimental re-design applied to parallel nonlinear dynamic processes that aims to precisely estimate the parameter set of macro kinetic growth models with minimal experimental effort. This provides a systematic solution for rapid validation of a specific model to new strains, mutants, or products. In biosciences, this is especially important as model identification is a long and laborious process which is continuing to limit the use of mathematical modeling in this field. The strength of this approach is demonstrated by fitting a macro-kinetic differential equation model for Escherichia coli fed-batch processes after 6 h of cultivation. The system includes two fully-automated liquid handling robots; one containing eight mini-bioreactors and another used for automated at-line analyses, which allows for the immediate use of the available data in the modeling environment. As a result, the experiment can be continually re-designed while the cultivations are running using the information generated by periodical parameter estimations. The advantages of an online re-computation of the optimal experiment are proven by a 50-fold lower average coefficient of variation on the parameter estimates compared to the sequential method (4.83% instead of 235.86%). The success obtained in such a complex system is a further step towards a more efficient computer aided bioprocess development. Biotechnol. Bioeng. 2017;114: 610-619. © 2016 Wiley Periodicals, Inc. © 2016 Wiley Periodicals, Inc.

Experimental results on photon-photon interactions at Adone

International Nuclear Information System (INIS)

Baldini Celio, R.; Capon, G.; Fabbro, R. del; Santis, P. de; Grilli, M.; Iarocci, E.; Mencuccini, C.; Murtas, G.P.; Spinetti, M.; Valente, V.; Bacci, C.; Zorzi, C. de; Penso, G.; Stella, B.

1979-01-01

Experimental results for the reactions e + e - →e + e - +X are presented for X=e + e - ,μ + μ - ,π + π - ,eta'. A tagging technique has been used to detect final electrons and positrons. A QED test is performed and an upper limit of 20 keV is derived for the partial width GAMMA(eta'→γγ). (Auth.)

New synthetic thrombin inhibitors: molecular design and experimental verification.

Science.gov (United States)

Sinauridze, Elena I; Romanov, Alexey N; Gribkova, Irina V; Kondakova, Olga A; Surov, Stepan S; Gorbatenko, Aleksander S; Butylin, Andrey A; Monakov, Mikhail Yu; Bogolyubov, Alexey A; Kuznetsov, Yuryi V; Sulimov, Vladimir B; Ataullakhanov, Fazoyl I

2011-01-01

The development of new anticoagulants is an important goal for the improvement of thromboses treatments. The design, synthesis and experimental testing of new safe and effective small molecule direct thrombin inhibitors for intravenous administration. Computer-aided molecular design of new thrombin inhibitors was performed using our original docking program SOL, which is based on the genetic algorithm of global energy minimization in the framework of a Merck Molecular Force Field. This program takes into account the effects of solvent. The designed molecules with the best scoring functions (calculated binding energies) were synthesized and their thrombin inhibitory activity evaluated experimentally in vitro using a chromogenic substrate in a buffer system and using a thrombin generation test in isolated plasma and in vivo using the newly developed model of hemodilution-induced hypercoagulation in rats. The acute toxicities of the most promising new thrombin inhibitors were evaluated in mice, and their stabilities in aqueous solutions were measured. New compounds that are both effective direct thrombin inhibitors (the best K(I) was 50) in the thrombin generation assay of approximately 100 nM) were discovered. These compounds contain one of the following new residues as the basic fragment: isothiuronium, 4-aminopyridinium, or 2-aminothiazolinium. LD(50) values for the best new inhibitors ranged from 166.7 to >1111.1 mg/kg. A plasma-substituting solution supplemented with one of the new inhibitors prevented hypercoagulation in the rat model of hemodilution-induced hypercoagulation. Activities of the best new inhibitors in physiological saline (1 µM solutions) were stable after sterilization by autoclaving, and the inhibitors remained stable at long-term storage over more than 1.5 years at room temperature and at 4°C. The high efficacy, stability and low acute toxicity reveal that the inhibitors that were developed may be promising for potential medical applications.

Experimental fusion power reactor conceptual design study. Final report. Volume III

International Nuclear Information System (INIS)

Baker, C.C.

1976-12-01

This document is the final report which describes the work carried out by General Atomic Company for the Electric Power Research Institute on a conceptual design study of a fusion experimental power reactor (EPR) and an overall EPR facility. The primary objective of the two-year program was to develop a conceptual design of an EPR that operates at ignition and produces continuous net power. A conceptual design was developed for a Doublet configuration based on indications that a noncircular tokamak offers the best potential of achieving a sufficiently high effective fuel containment to provide a viable reactor concept at reasonable cost. Other objectives included the development of a planning cost estimate and schedule for the plant and the identification of critical R and D programs required to support the physics development and engineering and construction of the EPR. This volume contains the following appendices: (1) tradeoff code analysis, (2) residual mode transport, (3) blanket/first wall design evaluations, (4) shielding design evaluation, (5) toroidal coil design evaluation, (6) E-coil design evaluation, (7) F-coil design evaluation, (8) plasma recycle system design evaluation, (9) primary coolant purification design evaluation, (10) power supply system design evaluation, (11) number of coolant loops, (12) power conversion system design evaluation, and (13) maintenance methods evaluation

The emergency braking module for an electronic copilot design and first results

Energy Technology Data Exchange (ETDEWEB)

Ameling, C.; Kirchner, A. [Univ. of the Federal Armed Forces Hamburg (Germany). Dept. of Mechanical Engineering

2000-07-01

This paper deals with design and development of an emergency braking module for an electronic copilot (ECP). ECP is used within an autonomous vehicle as a partial redundant system for vehicle control. ECP receives the necessary information about the positions and relative velocities of obstacles from various sources such as laserscanner or vision sensors. In the current stage of development the emergency breaking module computes, whether an object collides with the front of the vehicle. If the time-to-collision falls below the braking capacity an emergency braking is triggered. Experimental results show the capabilities of the system. (orig.)

Structural and compositional features of high-rise buildings: experimental design in Yekaterinburg

Science.gov (United States)

Yankovskaya, Yulia; Lobanov, Yuriy; Temnov, Vladimir

2018-03-01

The study looks at the specifics of high-rise development in Yekaterinburg. High-rise buildings are considered in the context of their historical development, structural features, compositional and imaginative design techniques. Experience of Yekaterinburg architects in experimental design is considered and analyzed. Main issues and prospects of high-rise development within the Yekaterinburg structure are studied. The most interesting and significant conceptual approaches to the structural and compositional arrangement of high-rise buildings are discussed.

The participation of the Experimental Design Factory of the Uranium Industry of Czechoslovakia in the design of a tunneling machine with disk bits

Energy Technology Data Exchange (ETDEWEB)

Kastner, P

1983-01-01

A tunneling machine, two prototypes of which were designed and built jointly on the basis of scientific and technical cooperation between the Experimental Design Factory of the Uranium Industry of Czechoslovakia and the VEB-Schachtbau enterprise (East Germany), is described. The experimental design operations were conducted under the methodological leadership of the Mine Construction in the Uranium Industry (Czechoslovakia) enterprise. The experimental design factory developed a general design system for the machine and its individual subassemblies. The detailed technical documentation for the machine units was developed by both enterprises. Each enterprise made two complexes of specific units and spare parts. The prototypes were assembled in both countries with the technical assistance of the producer enterprise of the appropriate subassembly. Industrial tests were conducted by each enterprise independently with technical assistance and delivery of spare parts on the part of the producer enterprise. A machine under the title of VM 24-27 was used to drill more than 2,300 meters of water supply tunnel in East Germany in 1982 and a machine called the RS 24-27 (29) was used in Prague in the same year to drill approximately 1,400 meters of cable collectors. The machine is designed for the passage of rounded mine drifts with a diameter of 2.4 to 2.7 (2.9) meters) to the full cross section in stable rocks. Its overall length is 32.5 meters, while the total weight is 85 tons. The shift productivity was 9.55 meters. Since 1979 the Mining Construction in the Uranium Industry and the Experimental Design Plant of the Uranium Industry Enterprises of Czechoslovakia have supplied disk bits for the TVM Demag tunnel drilling machines (West Germany) and RS 24-27 and the HG 210 Wirth (West Germany) cross cut drills.

Wireless power transfer in the presence of metallic plates: Experimental results

Directory of Open Access Journals (Sweden)

Xiaofang Yu

2013-06-01

Full Text Available We demonstrate efficient wireless power transfer between two high Q resonators, especially in a complex electromagnetic environment. In the close proximity of metallic plates, the transfer efficiency stays roughly the same as the free space efficiency with proper designs. The experimental data fits well with a coupled theory model. Resonance frequency matching, alignment of the magnetic field, and impedance matching are shown to be the most important factors for efficient wireless power transfer.

Thermal design of horizontal tube boilers: numerical and experimental investigation

International Nuclear Information System (INIS)

Roser, Robert

1999-01-01

This work concerns the thermal design of kettle re-boilers. Current methods are highly inaccurate, regarded to the correlations for external heat transfer coefficient at one tube scale, as well as to two-phase flow modelling at boiler scale. The aim of this work is to improve these thermal design methods. It contains an experimental investigation with typical operating conditions of such equipment: an hydrocarbon (n-pentane) with low mass flux. This investigation has lead to characterize the local flow pattern through void fraction measurements and, from this, to develop correlations for void fraction, pressure drop and heat transfer coefficient. The approach is original, since the developed correlations are based on the liquid velocity at minimum cross section area between tubes, as variable characterizing the hydrodynamic effects on pressure drop and heat transfer coefficient. These correlations are shown to give much better results than those suggested up to now in the literature, which are empirical transpositions from methods developed for inside tube flows. Furthermore, the numerical code MC3D has been applied using the correlations developed in this work, leading to a modelization of the two-phase flow in the boiler, which is a significant progress compared to current simplified methods. (author) [fr

TU-H-BRA-07: Design, Construction, and Installation of An Experimental Beam Line for the Development of MRI-Linac Compatible Electron Accelerator

International Nuclear Information System (INIS)

Whelan, B; Keall, P; Holloway, L; Gierman, S; Schmerge, J; Tantawi, S; Tremaine, A; Trautwein, A; Scott, B; Fahrig, R

2016-01-01

Purpose: MRI guided radiation therapy (MRIgRT) is a rapidly growing field; however, Linac operation in MRI fringe fields represents an ongoing challenge. We have previously shown in-silico that Linacs could be redesigned to function in the in-line orientation with no magnetic shielding by adopting an RF-gun configuration. Other authors have also published insilico studies of Linac operation in magnetic fields; however to date no experimental validation data is published. This work details the design, construction, and installation of an experimental beam line to validate our in-silico results. Methods: An RF-gun comprising 1.5 accelerating cells and capable of generating electron energies up to 3.2MeV is used. The experimental apparatus was designed to monitor both beam current (toroid current monitor), spot size (two phosphor screens with viewports), and generate peak magnetic fields of at least 1000G (three variable current electromagnetic coils). Thermal FEM simulations were developed to ensure coil temperature remained within 100degC. Other design considerations included beam disposal, vacuum maintenance, radiation shielding, earthquake safety, and machine protection interlocks. Results: The beam line has been designed, built, and installed in a radiation shielded bunker. Water cooling, power supplies, thermo-couples, cameras, and radiation shielding have been successfully connected and tested. Interlock testing, vacuum processing, and RF processing have been successfully completed. The first beam on is expected within weeks. The coil heating simulations show that with care, peak fields of up to 1200G (320G at cathode) can be produced using 40A current, which is well within the fields expected for MRI-Linac systems. The maximum coil temperature at this current was 84degC after 6 minutes. Conclusion: An experimental beam line has been constructed and installed at SLAC in order to experimentally characterise RF gun performance in in-line magnetic fields, validate

TU-H-BRA-07: Design, Construction, and Installation of An Experimental Beam Line for the Development of MRI-Linac Compatible Electron Accelerator

Energy Technology Data Exchange (ETDEWEB)

Whelan, B; Keall, P [University of Sydney, Sydney (Australia); Holloway, L [Liverpool Hospital and Ingham Institute, Liverpool, NSW (United Kingdom); Gierman, S; Schmerge, J; Tantawi, S; Tremaine, A; Trautwein, A; Scott, B [Stanford Linear Accelerator Facility, Palo Alto, CA (United States); Fahrig, R [Siemens Healthcare GmbH, Forchheim (Germany)

2016-06-15

Purpose: MRI guided radiation therapy (MRIgRT) is a rapidly growing field; however, Linac operation in MRI fringe fields represents an ongoing challenge. We have previously shown in-silico that Linacs could be redesigned to function in the in-line orientation with no magnetic shielding by adopting an RF-gun configuration. Other authors have also published insilico studies of Linac operation in magnetic fields; however to date no experimental validation data is published. This work details the design, construction, and installation of an experimental beam line to validate our in-silico results. Methods: An RF-gun comprising 1.5 accelerating cells and capable of generating electron energies up to 3.2MeV is used. The experimental apparatus was designed to monitor both beam current (toroid current monitor), spot size (two phosphor screens with viewports), and generate peak magnetic fields of at least 1000G (three variable current electromagnetic coils). Thermal FEM simulations were developed to ensure coil temperature remained within 100degC. Other design considerations included beam disposal, vacuum maintenance, radiation shielding, earthquake safety, and machine protection interlocks. Results: The beam line has been designed, built, and installed in a radiation shielded bunker. Water cooling, power supplies, thermo-couples, cameras, and radiation shielding have been successfully connected and tested. Interlock testing, vacuum processing, and RF processing have been successfully completed. The first beam on is expected within weeks. The coil heating simulations show that with care, peak fields of up to 1200G (320G at cathode) can be produced using 40A current, which is well within the fields expected for MRI-Linac systems. The maximum coil temperature at this current was 84degC after 6 minutes. Conclusion: An experimental beam line has been constructed and installed at SLAC in order to experimentally characterise RF gun performance in in-line magnetic fields, validate

Digital learning material for experimental design and model building in molecular biology

NARCIS (Netherlands)

Aegerter-Wilmsen, T.

2005-01-01

Designing experimental approaches is a major cognitive skill in molecular biology research, and building models, including quantitative ones, is a cognitive skill which is rapidly gaining importance. Since molecular biology education at university level is aimed at educating future researchers, we

Research on PCPV for BWR - physical model as design tool - main results

International Nuclear Information System (INIS)

Fumagalli, E.; Verdelli, G.

1975-01-01

ISMES (Experimental Institute for Models and Structures) is now carrying out a series of tests on physical models as a part of a research programme sponsored by DSR (Studies and Research Direction) of ENEL (Italian State Electricity Board) on behalf of CPN (Nuclear Design and Construction Centre) of ENEL with the aim to experience a 'Thin'-walled PCPV for 'BWR'. The physical model, together with the mathematical model and the rheological model of the materials, is intended as a meaningful design tool. The mathematical model covers the overall structural design phase, (geometries) and the linear behaviour, whereas the physical model, besides of a global information to be compared with the results of the mathematical model, supplies a number of data as the non-linear behaviour up to failure and local conditions (penetration area etc.) are concerned. The aim of the first phase of this research programme is to make a comparison between the calculation and experiment tests as the thicknesses of the wall and the bottom slab are concerned, whereas the second phase of the research deals with the behaviour of the removable lid and its connection with the main structure. To do this, a model in scale 1:10 has been designed which symmetrically reproduces with respect to the equator, the bottom part of the structure. In the bottom slab the penetrations of the prototype design are reproduced, whereas the upper slab is plain. This paper describes the model, and illustrates the main results, underlining the different behaviour of the upper and bottom slabs up to collapse

VX hydrolysis by human serum paraoxonase 1: a comparison of experimental and computational results.

Directory of Open Access Journals (Sweden)

Matthew W Peterson

Full Text Available Human Serum paraoxonase 1 (HuPON1 is an enzyme that has been shown to hydrolyze a variety of chemicals including the nerve agent VX. While wildtype HuPON1 does not exhibit sufficient activity against VX to be used as an in vivo countermeasure, it has been suggested that increasing HuPON1's organophosphorous hydrolase activity by one or two orders of magnitude would make the enzyme suitable for this purpose. The binding interaction between HuPON1 and VX has recently been modeled, but the mechanism for VX hydrolysis is still unknown. In this study, we created a transition state model for VX hydrolysis (VX(ts in water using quantum mechanical/molecular mechanical simulations, and docked the transition state model to 22 experimentally characterized HuPON1 variants using AutoDock Vina. The HuPON1-VX(ts complexes were grouped by reaction mechanism using a novel clustering procedure. The average Vina interaction energies for different clusters were compared to the experimentally determined activities of HuPON1 variants to determine which computational procedures best predict how well HuPON1 variants will hydrolyze VX. The analysis showed that only conformations which have the attacking hydroxyl group of VX(ts coordinated by the sidechain oxygen of D269 have a significant correlation with experimental results. The results from this study can be used for further characterization of how HuPON1 hydrolyzes VX and design of HuPON1 variants with increased activity against VX.

Experimental and numerical validation of a two-region-designed pebble bed reactor with dynamic core

International Nuclear Information System (INIS)

Jiang, S.Y.; Yang, X.T.; Tang, Z.W.; Wang, W.J.; Tu, J.Y.; Liu, Z.Y.; Li, J.

2012-01-01

Highlights: ► The experimental installation has been built to investigate the pebble flow. ► The feasibility of two-region pebble bed reactor has been verified. ► The pebble flow is more uniform in a taller vessel than that in a lower vessel. ► Larger base cone angle will decrease the scale of the stagnant zone. - Abstract: The pebble flow is the principal issue for the design of the pebble bed reactor. In order to verify the feasibility of a two-region-designed pebble bed reactor, the experimental installation with a taller vessel has been built, which is proportional to the real pebble bed reactor. With the aid of the experimental installation, the stable establishment and maintenance of the two-region arrangement has been verified, at the same time, the applicability of the DEM program has been also validated. Research results show: (1) The pebble's bouncing on the free surface is an important factor for the mixing of the different colored pebbles. (2) Through the guide plates installed in the top of the pebble packing, the size of the mixing zone can be reduced from 6–7 times to 3–4 times the pebble diameter. (3) The relationship between the width of the central region and the ratio of loading pebbles is approximately linear in the taller vessel. (4) The heighten part of the pebble packing can improve the uniformity of the flowing in the lower. (5) To increase the base cone angle can decrease the scale of the stagnant zone. All of these conclusions are meaningful to the design of the real pebble reactor.

An experimental method for designing the municipal solid waste biodrying

International Nuclear Information System (INIS)

Rada, E.C.; Politecnico Univ., Bucarest; Franzinelli, A.; Taiss, M.; Ragazzi, M.; Panaitescu, V.; Apostol, T.

2005-01-01

In the management of Municipal Solid Waste (MSW), in agreement with the new European directives concerning the valorization of materials and energy recovery, a recent approach based on a one-stream Biological Mechanical Treatment (BMT) is spreading as an alternative to the traditional two-stream approach. The bio-mechanical treatment of MSW is an increasing option either as a pre-treatment before land filling or as a pre-treatment before combustion. In the present paper an experimental method for designing the Municipal Solid Waste bio-drying is proposed. That means this paper deals with the option of energy recovery. The aim is to provide design criteria for bio-drying plants independent from the patents available in the sector [it

Observer Based Sliding Mode Attitude Control: Theoretical and Experimental Results

Directory of Open Access Journals (Sweden)

U. Jørgensen

2011-07-01

Full Text Available In this paper we present the design of a sliding mode controller for attitude control of spacecraft actuated by three orthogonal reaction wheels. The equilibrium of the closed loop system is proved to be asymptotically stable in the sense of Lyapunov. Due to cases where spacecraft do not have angular velocity measurements, an estimator for the generalized velocity is derived and asymptotic stability is proven for the observer. The approach is tested on an experimental platform with a sphere shaped Autonomous Underwater Vehicle SATellite: AUVSAT, developed at the Norwegian University of Science and Technology.

Experimental system design of liquid lithium-lead alloy bubbler for DFLL-TBM

International Nuclear Information System (INIS)

Xie Bo; Li Junge; Xu Shaomei; Weng Kuiping

2011-01-01

The liquid lithium-lead alloy bubbler is a very important composition in the tritium unit of Chinese Dual-Functional Lithium Lead Test Blanket Module (DFLL-TBM). In order to complete the construction and run of the bubbler experimental system,overall design of the system, main circuit design and auxiliary system design have been proposed on the basis of theoretical calculations for the interaction of hydrogen isotope with lithium-lead alloy and experiment for hydrogen extraction from liquid lithium-lead alloy by bubbling with rotational jet nozzle. The key of this design is gas-liquid exchange packed column, to achieve the measurement and extraction of hydrogen isotopes from liquid lithium-lead alloy. (authors)

Fast Bayesian optimal experimental design for seismic source inversion

KAUST Repository

Long, Quan

2015-07-01

We develop a fast method for optimally designing experiments in the context of statistical seismic source inversion. In particular, we efficiently compute the optimal number and locations of the receivers or seismographs. The seismic source is modeled by a point moment tensor multiplied by a time-dependent function. The parameters include the source location, moment tensor components, and start time and frequency in the time function. The forward problem is modeled by elastodynamic wave equations. We show that the Hessian of the cost functional, which is usually defined as the square of the weighted L2 norm of the difference between the experimental data and the simulated data, is proportional to the measurement time and the number of receivers. Consequently, the posterior distribution of the parameters, in a Bayesian setting, concentrates around the "true" parameters, and we can employ Laplace approximation and speed up the estimation of the expected Kullback-Leibler divergence (expected information gain), the optimality criterion in the experimental design procedure. Since the source parameters span several magnitudes, we use a scaling matrix for efficient control of the condition number of the original Hessian matrix. We use a second-order accurate finite difference method to compute the Hessian matrix and either sparse quadrature or Monte Carlo sampling to carry out numerical integration. We demonstrate the efficiency, accuracy, and applicability of our method on a two-dimensional seismic source inversion problem. © 2015 Elsevier B.V.

Fast Bayesian Optimal Experimental Design for Seismic Source Inversion

KAUST Repository

Long, Quan

2016-01-06

We develop a fast method for optimally designing experiments [1] in the context of statistical seismic source inversion [2]. In particular, we efficiently compute the optimal number and locations of the receivers or seismographs. The seismic source is modeled by a point moment tensor multiplied by a time-dependent function. The parameters include the source location, moment tensor components, and start time and frequency in the time function. The forward problem is modeled by the elastic wave equations. We show that the Hessian of the cost functional, which is usually defined as the square of the weighted L2 norm of the difference between the experimental data and the simulated data, is proportional to the measurement time and the number of receivers. Consequently, the posterior distribution of the parameters, in a Bayesian setting, concentrates around the true parameters, and we can employ Laplace approximation and speed up the estimation of the expected Kullback-Leibler divergence (expected information gain), the optimality criterion in the experimental design procedure. Since the source parameters span several magnitudes, we use a scaling matrix for efficient control of the condition number of the original Hessian matrix. We use a second-order accurate finite difference method to compute the Hessian matrix and either sparse quadrature or Monte Carlo sampling to carry out numerical integration. We demonstrate the efficiency, accuracy, and applicability of our method on a two-dimensional seismic source inversion problem.

Fast Bayesian Optimal Experimental Design for Seismic Source Inversion

KAUST Repository

Long, Quan; Motamed, Mohammad; Tempone, Raul

2016-01-01

We develop a fast method for optimally designing experiments [1] in the context of statistical seismic source inversion [2]. In particular, we efficiently compute the optimal number and locations of the receivers or seismographs. The seismic source is modeled by a point moment tensor multiplied by a time-dependent function. The parameters include the source location, moment tensor components, and start time and frequency in the time function. The forward problem is modeled by the elastic wave equations. We show that the Hessian of the cost functional, which is usually defined as the square of the weighted L2 norm of the difference between the experimental data and the simulated data, is proportional to the measurement time and the number of receivers. Consequently, the posterior distribution of the parameters, in a Bayesian setting, concentrates around the true parameters, and we can employ Laplace approximation and speed up the estimation of the expected Kullback-Leibler divergence (expected information gain), the optimality criterion in the experimental design procedure. Since the source parameters span several magnitudes, we use a scaling matrix for efficient control of the condition number of the original Hessian matrix. We use a second-order accurate finite difference method to compute the Hessian matrix and either sparse quadrature or Monte Carlo sampling to carry out numerical integration. We demonstrate the efficiency, accuracy, and applicability of our method on a two-dimensional seismic source inversion problem.

Experimental results for a 1.5 MW, 110 GHz gyrotron oscillator with reduced mode competition

Science.gov (United States)

Choi, E. M.; Marchewka, C. D.; Mastovsky, I.; Sirigiri, J. R.; Shapiro, M. A.; Temkin, R. J.

2006-02-01

A new result from a 110GHz gyrotron at MIT is reported with an output power of 1.67MW and an efficiency of 42% when operated at 97kV and 41A for 3μs pulses in the TE22,6 mode. These results are a major improvement over results obtained with an earlier cavity design, which produced 1.43MW of power at 37% efficiency. These new results were obtained using a cavity with a reduced output taper angle and a lower ohmic loss when compared with the earlier cavity. The improved operation is shown experimentally to be the result of reduced mode competition from the nearby TE19,7 mode. The reduced mode competition agrees well with an analysis of the startup scenario based on starting current simulations. The present results should prove useful in planning long pulse and CW versions of the 110GHz gyrotron.

Experimental results for a 1.5 MW, 110 GHz gyrotron oscillator with reduced mode competition

International Nuclear Information System (INIS)

Choi, E.M.; Marchewka, C.D.; Mastovsky, I.; Sirigiri, J.R.; Shapiro, M.A.; Temkin, R.J.

2006-01-01

A new result from a 110 GHz gyrotron at MIT is reported with an output power of 1.67 MW and an efficiency of 42% when operated at 97 kV and 41 A for 3 μs pulses in the TE 22,6 mode. These results are a major improvement over results obtained with an earlier cavity design, which produced 1.43 MW of power at 37% efficiency. These new results were obtained using a cavity with a reduced output taper angle and a lower ohmic loss when compared with the earlier cavity. The improved operation is shown experimentally to be the result of reduced mode competition from the nearby TE 19,7 mode. The reduced mode competition agrees well with an analysis of the startup scenario based on starting current simulations. The present results should prove useful in planning long pulse and CW versions of the 110 GHz gyrotron

Experimental results obtained with the simulated cold moderator system. System characteristics and technical issues

Energy Technology Data Exchange (ETDEWEB)

Aso, Tomokazu; Kaminaga, Masanori; Haga, Katsuhiro; Kinoshita, Hidetaka; Takahashi, Toshio; Hino, Ryutaro [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

2002-12-01

The Japan Atomic Energy Research Institute and the High Energy Accelerator Research Organization have been developing a Mega-Watt scale spallation target system. In the system, neutrons generated in a target are sorted out their energy to the proper values in liquid-hydrogen moderators. Then, the liquid-hydrogen is forced to circulate in order to suppress hydrogen temperature increase. In the operation of moderators, it is very important to establish a safety protection system against emergency shutdown of the accelerator or accidents of the cold moderator system. In order to obtain a technical data for design and safety review of the liquid-hydrogen system, we have fabricated an experimental apparatus simulated the cold moderator system using liquid nitrogen (max. 1.5 MPa, mini. 77 K) instead of liquid hydrogen. The experiments on a controllability of the system were carried out to investigate dynamic characteristics of the system. This report presents the experimental results and technical issues for the construction of a practical liquid-hydrogen moderator system of the Mega-Watt scale target system. (author)

Experimental validation of 3D printed material behaviors and their influence on the structural topology design

Science.gov (United States)

Yang, Kai Ke; Zhu, Ji Hong; Wang, Chuang; Jia, Dong Sheng; Song, Long Long; Zhang, Wei Hong

2018-05-01

The purpose of this paper is to investigate the structures achieved by topology optimization and their fabrications by 3D printing considering the particular features of material microstructures and macro mechanical performances. Combining Digital Image Correlation and Optical Microscope, this paper experimentally explored the anisotropies of stiffness and strength existing in the 3D printed polymer material using Stereolithography (SLA) and titanium material using Selective Laser Melting (SLM). The standard specimens and typical structures obtained by topology optimization were fabricated along different building directions. On the one hand, the experimental results of these SLA produced structures showed stable properties and obviously anisotropic rules in stiffness, ultimate strengths and places of fractures. Further structural designs were performed using topology optimization when the particular mechanical behaviors of SLA printed materials were considered, which resulted in better structural performances compared to the optimized designs using `ideal' isotropic material model. On the other hand, this paper tested the mechanical behaviors of SLM printed multiscale lattice structures which were fabricated using the same metal powder and the same machine. The structural stiffness values are generally similar while the strength behaviors show a difference, which are mainly due to the irregular surface quality of the tiny structural branches of the lattice. The above evidences clearly show that the consideration of the particular behaviors of 3D printed materials is therefore indispensable for structural design and optimization in order to improve the structural performance and strengthen their practical significance.

Experimental validation of 3D printed material behaviors and their influence on the structural topology design

Science.gov (United States)

Yang, Kai Ke; Zhu, Ji Hong; Wang, Chuang; Jia, Dong Sheng; Song, Long Long; Zhang, Wei Hong

2018-02-01

The purpose of this paper is to investigate the structures achieved by topology optimization and their fabrications by 3D printing considering the particular features of material microstructures and macro mechanical performances. Combining Digital Image Correlation and Optical Microscope, this paper experimentally explored the anisotropies of stiffness and strength existing in the 3D printed polymer material using Stereolithography (SLA) and titanium material using Selective Laser Melting (SLM). The standard specimens and typical structures obtained by topology optimization were fabricated along different building directions. On the one hand, the experimental results of these SLA produced structures showed stable properties and obviously anisotropic rules in stiffness, ultimate strengths and places of fractures. Further structural designs were performed using topology optimization when the particular mechanical behaviors of SLA printed materials were considered, which resulted in better structural performances compared to the optimized designs using `ideal' isotropic material model. On the other hand, this paper tested the mechanical behaviors of SLM printed multiscale lattice structures which were fabricated using the same metal powder and the same machine. The structural stiffness values are generally similar while the strength behaviors show a difference, which are mainly due to the irregular surface quality of the tiny structural branches of the lattice. The above evidences clearly show that the consideration of the particular behaviors of 3D printed materials is therefore indispensable for structural design and optimization in order to improve the structural performance and strengthen their practical significance.

Conceptual design of superconducting magnet systems for the Argonne Tokamak Experimental Power Reactor

International Nuclear Information System (INIS)

Wang, S.T.; Turner, L.R.; Mills, F.E.; DeMichele, D.W.; Smelser, P.; Kim, S.H.

1976-01-01

As an integral effort in the Argonne Tokamak Experimental Power Reactor Conceptual Design, the conceptual design of a 10-tesla, pure-tension superconducting toroidal-field (TF) coil system has been developed in sufficient detail to define a realistic design for the TF coil system that could be built based upon the current state of technology with minimum technological extrapolations. A conceptual design study on the superconducting ohmic-heating (OH) coils and the superconducting equilibrium-field (EF) coils were also completed. These conceptual designs are developed in sufficient detail with clear information on high current ac conductor design, cooling, venting provision, coil structural support and zero loss poloidal coil cryostat design. Also investigated is the EF penetration into the blanket and shield

First experimental results on CMOS Integrated Nickel Electroplated Resonators

DEFF Research Database (Denmark)

Yalcinkaya, Arda Deniz; Hansen, Ole

2004-01-01

This paper presents experimental results on MEMS metallic add-on post-fabrication effects on complementary metal oxide semiconductor (CMOS) transistors. Two versions of add-on processing, that use either e-beam evaporation or magnetron sputtering, are compared through investigation of the electri...

Testing the Developmental Origins of Health and Disease Hypothesis for Psychopathology Using Family-Based Quasi-Experimental Designs

Science.gov (United States)

D’Onofrio, Brian M.; Class, Quetzal A.; Lahey, Benjamin B.; Larsson, Henrik

2014-01-01

The Developmental Origin of Health and Disease (DOHaD) hypothesis is a broad theoretical framework that emphasizes how early risk factors have a causal influence on psychopathology. Researchers have raised concerns about the causal interpretation of statistical associations between early risk factors and later psychopathology because most existing studies have been unable to rule out the possibility of environmental and genetic confounding. In this paper we illustrate how family-based quasi-experimental designs can test the DOHaD hypothesis by ruling out alternative hypotheses. We review the logic underlying sibling-comparison, co-twin control, offspring of siblings/twins, adoption, and in vitro fertilization designs. We then present results from studies using these designs focused on broad indices of fetal development (low birth weight and gestational age) and a particular teratogen, smoking during pregnancy. The results provide mixed support for the DOHaD hypothesis for psychopathology, illustrating the critical need to use design features that rule out unmeasured confounding. PMID:25364377

QuantifyMe: An Open-Source Automated Single-Case Experimental Design Platform

Directory of Open Access Journals (Sweden)

Sara Taylor

2018-04-01

Full Text Available Smartphones and wearable sensors have enabled unprecedented data collection, with many products now providing feedback to users about recommended step counts or sleep durations. However, these recommendations do not provide personalized insights that have been shown to be best suited for a specific individual. A scientific way to find individualized recommendations and causal links is to conduct experiments using single-case experimental design; however, properly designed single-case experiments are not easy to conduct on oneself. We designed, developed, and evaluated a novel platform, QuantifyMe, for novice self-experimenters to conduct proper-methodology single-case self-experiments in an automated and scientific manner using their smartphones. We provide software for the platform that we used (available for free on GitHub, which provides the methodological elements to run many kinds of customized studies. In this work, we evaluate its use with four different kinds of personalized investigations, examining how variables such as sleep duration and regularity, activity, and leisure time affect personal happiness, stress, productivity, and sleep efficiency. We conducted a six-week pilot study (N = 13 to evaluate QuantifyMe. We describe the lessons learned developing the platform and recommendations for its improvement, as well as its potential for enabling personalized insights to be scientifically evaluated in many individuals, reducing the high administrative cost for advancing human health and wellbeing.

QuantifyMe: An Open-Source Automated Single-Case Experimental Design Platform.

Science.gov (United States)

Taylor, Sara; Sano, Akane; Ferguson, Craig; Mohan, Akshay; Picard, Rosalind W

2018-04-05

Smartphones and wearable sensors have enabled unprecedented data collection, with many products now providing feedback to users about recommended step counts or sleep durations. However, these recommendations do not provide personalized insights that have been shown to be best suited for a specific individual. A scientific way to find individualized recommendations and causal links is to conduct experiments using single-case experimental design; however, properly designed single-case experiments are not easy to conduct on oneself. We designed, developed, and evaluated a novel platform, QuantifyMe, for novice self-experimenters to conduct proper-methodology single-case self-experiments in an automated and scientific manner using their smartphones. We provide software for the platform that we used (available for free on GitHub), which provides the methodological elements to run many kinds of customized studies. In this work, we evaluate its use with four different kinds of personalized investigations, examining how variables such as sleep duration and regularity, activity, and leisure time affect personal happiness, stress, productivity, and sleep efficiency. We conducted a six-week pilot study ( N = 13) to evaluate QuantifyMe. We describe the lessons learned developing the platform and recommendations for its improvement, as well as its potential for enabling personalized insights to be scientifically evaluated in many individuals, reducing the high administrative cost for advancing human health and wellbeing.

Quantitative comparison between theoretical predictions and experimental results for the BCS-BEC crossover

International Nuclear Information System (INIS)

Perali, A.; Pieri, P.; Strinati, G.C.

2004-01-01

Theoretical predictions for the Bardeen-Cooper-Schrieffer-Bose-Einstein condensation crossover of trapped Fermi atoms are compared with recent experimental results for the density profiles of L 6 i. The calculations rest on a single theoretical approach that includes pairing fluctuations beyond mean-field. Excellent agreement with experimental results is obtained. Theoretical predictions for the zero-temperature chemical potential and gap at the unitarity limit are also found to compare extremely well with Quantum Monte Carlo simulations and with recent experimental results

Robust Design of Docking Hoop for Recovery of Autonomous Underwater Vehicle with Experimental Results

Directory of Open Access Journals (Sweden)

Wei Peng Lin

2015-12-01

Full Text Available Control systems prototyping is usually constrained by model complexity, embedded system configurations, and interface testing. The proposed control system prototyping of a remotely-operated vehicle (ROV with a docking hoop (DH to recover an autonomous underwater vehicle (AUV named AUVDH using a combination of software tools allows the prototyping process to be unified. This process provides systematic design from mechanical, hydrodynamics, dynamics modelling, control system design, and simulation to testing in water. As shown in a three-dimensional simulation of an AUVDH model using MATLAB™/Simulink™ during the launch and recovery process, the control simulation of a sliding mode controller is able to control the positions and velocities under the external wave, current, and tether forces. In the water test using the proposed Python-based GUI platform, it shows that the AUVDH is capable to perform station-keeping under the external disturbances.

An innovative approach for planning and execution of pre-experimental runs for Design of Experiments

Directory of Open Access Journals (Sweden)

Muhammad Arsalan Farooq

2016-09-01

Full Text Available This paper addresses the study of the pre-experimental planning phase of the Design of Experiments (DoE in order to improve the final product quality. The pre-experimental planning phase includes a clear identification of the problem statement, selection of control factors and their respective levels and ranges. To improve production quality based on the DoE a new approach for the pre-experimental planning phase, called Non-Conformity Matrix (NCM, is presented. This article also addresses the key steps of the pre-experimental runs considering a consumer goods manufacturing process. Results of the application for an industrial case show that this methodology can support a clear definition of the problem and also a correct identification of the factor ranges in particular situations. The proposed new approach allows modeling the entire manufacturing system holistically and correctly defining the factor ranges and respective levels for a more effective application of DoE. This new approach can be a useful resource for both research and industrial practitioners who are dedicated to large DoE projects with unknown factor interactions, when the operational levels and ranges are not completely defined.

Design and Fabrication of an Experimental Microheater Array Powder Sintering Printer

Science.gov (United States)

Holt, Nicholas; Zhou, Wenchao

2018-03-01

Microheater array powder sintering (MAPS) is a novel additive manufacturing process that uses an array of microheaters to selectively sinter powder particles. MAPS shows great promise as a new method of printing flexible electronics by enabling digital curing of conductive inks on a variety of substrates. For MAPS to work effectively, a microscale air gap needs to be maintained between the heater array and the conductive ink. In this article, we present an experimental MAPS printer with air gap control for printing conductive circuits. First, we discuss design aspects necessary to implement MAPS. An analysis is performed to validate that the design can maintain the desired air gap between the microheaters and the sintering layer, which consists of a silver nanoparticle ink. The printer is tested by printing conductive lines on a flexible plastic substrate with silver nanoparticle ink. Results show MAPS performs on par with or better than the existing fabrication methods for printed electronics in terms of both the print quality (conductivity of the printed line) and print speed, which shows MAPS' great promise as a competitive new method for digital production of printed electronics.

Design of a digital beam attenuation system for computed tomography. Part II. Performance study and initial results

International Nuclear Information System (INIS)

Szczykutowicz, Timothy P.; Mistretta, Charles A.

2013-01-01

Purpose: The purpose of this work is to present a performance study of the digital beam attenuator (DBA) for implementing fluence field modulated CT (FFMCT) using a simulation framework developed to model the incorporation of the DBA into an existing CT system. Additionally, initial results will be presented using a prototype DBA and the realization of the prototype will be described. To our knowledge, this study represents the first experimental use of a device capable of modulating x-ray fluence as a function of fan angle using a CT geometry. Methods: To realize FFMCT, the authors propose to use a wedge design in which one wedge is held stationary and another wedge is moved over the stationary wedge. Due to the wedge shape, the composite thickness of the two wedges changes as a function of the amount of overlap between the wedges. This design allows for the wedges to modulate the photon fluence incident onto a patient. Using a simulation environment, the effect of changing the number of wedges has on dose, scatter, detector dynamic range, and noise uniformity is explored. Experimental results are presented using a prototype DBA having ten Fe wedges and a c-arm CT system geometry. The experimental DBA results are compared to non-DBA scans using scatter and detector dynamic range as metrics. Both flat field and bowtie filtered CT acquisitions were simulated for comparison with the DBA. Results: Numerical results suggest that substantial gains in noise uniformity and scatter-to-primary ratio (SPR) can be obtained using only seven wedges. After seven wedges, the decrease in noise ununiformity and SPR falls off at a lower rate. Simulations comparing CT acquisitions between flat field, bowtie enabled, and DBA CT acquisitions suggest DBA-FFMCT can reduce dose relative to flat field CT by ≈3 times. A bowtie filter under the same imaging conditions was shown to only allow a dose reduction of 1.65 times. Experimentally, a 10 wedge DBA prototype result showed a SPR

Analysis and Experimental Investigation of Optimum Design of Thermoelectric Cooling/Heating System for Car Seat Climate Control (CSCC)

Science.gov (United States)

Elarusi, Abdulmunaem; Attar, Alaa; Lee, HoSung

2018-02-01

The optimum design of a thermoelectric system for application in car seat climate control has been modeled and its performance evaluated experimentally. The optimum design of the thermoelectric device combining two heat exchangers was obtained by using a newly developed optimization method based on the dimensional technique. Based on the analytical optimum design results, commercial thermoelectric cooler and heat sinks were selected to design and construct the climate control heat pump. This work focuses on testing the system performance in both cooling and heating modes to ensure accurate analytical modeling. Although the analytical performance was calculated using the simple ideal thermoelectric equations with effective thermoelectric material properties, it showed very good agreement with experiment for most operating conditions.

Experimental results with hydrogen fueled internal combustion engines

Science.gov (United States)

De Boer, P. C. T.; Mclean, W. J.; Homan, H. S.

1975-01-01

The paper focuses on the most important experimental findings for hydrogen-fueled internal combustion engines, with particular reference to the application of these findings to the assessment of the potential of hydrogen engines. Emphasis is on the various tradeoffs that can be made, such as between maximum efficiency, maximum power, and minimum NO emissions. The various possibilities for induction and ignition are described. Some projections are made about areas in which hydrogen engines may find their initial application and about optimum ways to design such engines. It is shown that hydrogen-fueled reciprocal internal combustion engines offer important advantages with respect to thermal efficiency and exhaust emissions. Problems arising from preignition can suitably be avoided by restricting the fuel-air equivalence ratio to values below about 0.5. The direct cylinder injection appears to be a very attractive way to operate the engine, because it combines a wide range of possible power outputs with a high thermal efficiency and very low NO emissions at part loads.

Computer experimental analysis of the CHP performance of a 100 kW e SOFC Field Unit by a factorial design

Science.gov (United States)

Calì, M.; Santarelli, M. G. L.; Leone, P.

Gas Turbine Technologies (GTT) and Politecnico di Torino, both located in Torino (Italy), have been involved in the design and installation of a SOFC laboratory in order to analyse the operation, in cogenerative configuration, of the CHP 100 kW e SOFC Field Unit, built by Siemens-Westinghouse Power Corporation (SWPC), which is at present (May 2005) starting its operation and which will supply electric and thermal power to the GTT factory. In order to take the better advantage from the analysis of the on-site operation, and especially to correctly design the scheduled experimental tests on the system, we developed a mathematical model and run a simulated experimental campaign, applying a rigorous statistical approach to the analysis of the results. The aim of this work is the computer experimental analysis, through a statistical methodology (2 k factorial experiments), of the CHP 100 performance. First, the mathematical model has been calibrated with the results acquired during the first CHP100 demonstration at EDB/ELSAM in Westerwoort. After, the simulated tests have been performed in the form of computer experimental session, and the measurement uncertainties have been simulated with perturbation imposed to the model independent variables. The statistical methodology used for the computer experimental analysis is the factorial design (Yates' Technique): using the ANOVA technique the effect of the main independent variables (air utilization factor U ox, fuel utilization factor U F, internal fuel and air preheating and anodic recycling flow rate) has been investigated in a rigorous manner. Analysis accounts for the effects of parameters on stack electric power, thermal recovered power, single cell voltage, cell operative temperature, consumed fuel flow and steam to carbon ratio. Each main effect and interaction effect of parameters is shown with particular attention on generated electric power and stack heat recovered.

OIL DECONTAMINATION OF BOTTOM SEDIMENTS EXPERIMENTAL WORK RESULTS

Directory of Open Access Journals (Sweden)

Lushnikov Sergey V.

2006-08-01

Full Text Available This article presents the results of experimental work during 2004-2005 on oil decontamination of bottom sediments of Lake Schuchye, situated in the Komi Republic (Northern Russia. The cause of thecontamination were huge oil spills occurred after a series of accidental ruptures on the Harjaga-Usinsk and Vozej-Usinsk oil-pipe lines in 1994. Flotation technology was used for the cleaning of bottom sediments.157 tons of crude oil were removed during the course of 2-year experimental work from an area of 4,1 ha.The content of aliphatic and alicyclic oil hydrocarbons was reduced from 53,3 g/kg to 2,2 g/kg, on average.Hydrobiological investigations revealed that bottom sediments started to be inhabited by benthos organisms, dominantly Oligochaeta. Besides Oligochaeta, Chironomidae maggots and Bivalvia were detected. Theappearance of Macrozoobenthos organisms can serve as a bioindicator of water quality.

Design and experimental validation of the inlet guide vane system of a mini hydraulic bulb-turbine

Energy Technology Data Exchange (ETDEWEB)

Ferro, L.M.C. [Department of Mechanical Engineering, Escola Superior de Tecnologia de Setubal, Polytechnic Institute of Setubal, Campus do IPS, Estefanilha, 2910-761 Setubal (Portugal); IDMEC, Instituto Superior Tecnico, Technical University of Lisbon, Av. Rovisco Pais,1049-001 Lisboa (Portugal); Gato, L.M.C.; Falcao, A.F.O. [IDMEC, Instituto Superior Tecnico, Technical University of Lisbon, Av. Rovisco Pais,1049-001 Lisboa (Portugal)

2010-09-15

The paper presents a fast design method for the inlet guide vanes of low-cost mini hydraulic bulb turbines. The guide vanes are positioned between two conical surfaces with a common vertex and have constant thickness distribution, except close to the leading and the trailing edges. The conical-walled inlet guide vane row is designed using a quasi-three-dimensional calculation method, by prescribing the angular-momentum distribution along the span at the outlet section of the guide vanes. The meridional through-flow is computed by a streamline curvature method and the blade-to-blade flow by a singularity surface method. The stagger angle and the vane camber are computed to fulfil the required design circulation and zero-incidence flow at the leading edge. The final vane shape is a single-curvature surface with straight leading and trailing edges. To validate the design method, a conical-walled inlet guide vane row nozzle-model with six fixed vanes was designed, manufactured and tested in an airflow rig. Traversing measurements along the circumferential and radial directions were made with a five-hole probe. The experimental results are compared with the prescribed design conditions and with numerical results from the three-dimensional inviscid and viscous flow computed with the FLUENT code. (author)

Conceptual design of neutron diagnostic systems for fusion experimental reactor

International Nuclear Information System (INIS)

Iguchi, T.; Kaneko, J.; Nakazawa, M.

1994-01-01

Neutron measurement in fusion experimental reactors is very important for burning plasma diagnostics and control, monitoring of irradiation effects on device components, neutron source characterization for in-situ engineering tests, etc. A conceptual design of neutron diagnostic systems for an ITER-like fusion experimental reactor has been made, which consists of a neutron yield monitor, a neutron emission profile monitor and a 14-MeV spectrometer. Each of them is based on a unique idea to meet the required performances for full power conditions assumed at ITER operation. Micro-fission chambers of 235 U (and 238 U) placed at several poloidal angles near the first wall are adopted as a promising neutron yield monitor. A collimated long counter system using a 235 U fission chamber and graphite neutron moderators is also proposed to improve the calibration accuracy of absolute neutron yield determination

Design, Analysis, and Experimental Evaluation of a Double Coil Magnetorheological Fluid Damper

Directory of Open Access Journals (Sweden)

Guoliang Hu

2016-01-01

Full Text Available A magnetorheological (MR damper is one of the most advanced devices used in a semiactive control system to mitigate unwanted vibration because the damping force can be controlled by changing the viscosity of the internal magnetorheological (MR fluids. This study proposes a typical double coil MR damper where the damping force and dynamic range were derived from a quasistatic model based on the Bingham model of MR fluid. A finite element model was built to study the performance of this double coil MR damper by investigating seven different piston configurations, including the numbers and shapes of their chamfered ends. The objective function of an optimization problem was proposed and then an optimization procedure was constructed using the ANSYS parametric design language (APDL to obtain the optimal damping performance of a double coil MR damper. Furthermore, experimental tests were also carried out, and the effects of the same direction and reverse direction of the currents on the damping forces were also analyzed. The relevant results of this analysis can easily be extended to the design of other types of MR dampers.

Optical design of beam lines at the KEK-PS new experimental hall

International Nuclear Information System (INIS)

Tanaka, K.H.; Ieiri, M.; Noumi, H.; Minakawa, M.; Yamanoi, Y.; Kato, Y.; Ishii, H.; Suzuki, Y.; Takasaki, M.

1995-01-01

A new counter experimental hall [K.H. Tanaka et al., IEEE Trans. Magn. 28 (1992) 697] was designed and constructed at the KEK 12-GeV Proton Synchrotron (KEK-PS). The extracted proton beam from the KEK-PS is introduced to the new hall through the newly-prepared primary beam line, EP1, and hits two production targets in cascade. The upstream target provides secondary particles to the low momentum (0.4-0.6 GeV/c) separated beam line, K5, and the downstream target is connected to the medium momentum (0.6-2.0 GeV/c) separated beam line, K6. Several new ideas were employed in the beam optical designs of EP1, K5 and K6 in order to increase the number and the purity of the short-lived secondary particles, such as kaons and pions, under the limited energy and intensity of the primary protons provided by the KEK-PS. These new ideas are described in this paper as well as the first commissioning results. (orig.)

Thermal design, analysis, and experimental verification for a DIII-D cryogenic pump

International Nuclear Information System (INIS)

Baxi, C.B.; Anderson, P.; Langhorn, A.; Schaubel, K.; Smith, J.

1991-01-01

As part of the advanced divertor program, it is planned to install a 50 m 3 /s capacity cryopump for particle removal in the DIII-D tokamak. The cryopump will be located in the outer bottom corner of the vacuum vessel. The pump will consist of a surface at liquid helium temperature (helium panel) with a surface area of about 1 m 2 , a surface at liquid nitrogen temperature (nitrogen shield) to reduce radiation heat load on the helium panel, and a secondary shield around the nitrogen shield. The cryopump design poses a number of thermal hydraulic problems such as estimation of heat loads on helium and nitrogen panels, stability of the two-phase helium flow, performance of the pump components during high temperature bakeout, and cooldown performance of the helium panel from ambient temperatures. This paper presents the thermal analysis done to resolve these issues. A prototypic experiment performed at General Atomics verified the analysis and increased the confidence in the design. The experimental results are also summarized in this paper. (orig.)

Thermal design, analysis, and experimental verification for a DIII-D cryogenic pump

International Nuclear Information System (INIS)

Baxi, C.B.; Anderson, P.; Langhorn, A.; Schaubel, K.; Smith, J.

1991-08-01

As part of the advanced divertor program, it is planned to install a 50 m 3 /s capacity cryopump for particle removal in the D3-D tokamak. The cryopump will be located in the outer bottom corner of the vacuum vessel. The pump will consist of a surface at liquid helium temperature (helium panel) with a surface area of about 1 m 2 , a surface at liquid nitrogen temperature (nitrogen shield) to reduce radiation heat load on the helium panel, and a secondary shield around the nitrogen shield. The cryopump design poses a number of thermal hydraulic problems such as estimation of heat loads on helium and nitrogen panels, stability of the two-phase helium flow, performance of the pump components during high temperature bakeout, and cooldown performance of the helium panel from ambient temperatures. This paper presents the thermal analysis done to resolve these issues. A prototypic experiment performed at General Atomics verified the analysis and increased the confidence in the design. The experimental results are also summarized in this paper. 7 refs., 5 figs., 1 tab