Reusable Rack Interface Controller Common Software for Various Science Research Racks on the International Space Station

Science.gov (United States)

Lu, George C.

2003-01-01

The purpose of the EXPRESS (Expedite the PRocessing of Experiments to Space Station) rack project is to provide a set of predefined interfaces for scientific payloads which allow rapid integration into a payload rack on International Space Station (ISS). VxWorks' was selected as the operating system for the rack and payload resource controller, primarily based on the proliferation of VME (Versa Module Eurocard) products. These products provide needed flexibility for future hardware upgrades to meet everchanging science research rack configuration requirements. On the International Space Station, there are multiple science research rack configurations, including: 1) Human Research Facility (HRF); 2) EXPRESS ARIS (Active Rack Isolation System); 3) WORF (Window Observational Research Facility); and 4) HHR (Habitat Holding Rack). The RIC (Rack Interface Controller) connects payloads to the ISS bus architecture for data transfer between the payload and ground control. The RIC is a general purpose embedded computer which supports multiple communication protocols, including fiber optic communication buses, Ethernet buses, EIA-422, Mil-Std-1553 buses, SMPTE (Society Motion Picture Television Engineers)-170M video, and audio interfaces to payloads and the ISS. As a cost saving and software reliability strategy, the Boeing Payload Software Organization developed reusable common software where appropriate. These reusable modules included a set of low-level driver software interfaces to 1553B. RS232, RS422, Ethernet buses, HRDL (High Rate Data Link), video switch functionality, telemetry processing, and executive software hosted on the FUC computer. These drivers formed the basis for software development of the HRF, EXPRESS, EXPRESS ARIS, WORF, and HHR RIC executable modules. The reusable RIC common software has provided extensive benefits, including: 1) Significant reduction in development flow time; 2) Minimal rework and maintenance; 3) Improved reliability; and 4) Overall

Storage rack for spent nuclear fuels

International Nuclear Information System (INIS)

Kiyama, Yoichi.

1996-01-01

A storage rack comprises a number of rack cells for containing spent nuclear fuels and two upper and lower rack support plates. Small through holes are formed to lateral walls of the rack cell each at a position slightly above the position of the upper rack support plate. Finger members each having a protrusion which fits the small through hole is secured at the upper surface of the upper rack support plate. The finger member is a metal leaf-spring erected at the periphery of a rack insertion hole of the rack support plate. Gaps for allowing thermal expansion of the rack cell are formed each between the edge of the rack cell insertion hole of the rack support plate and the rack cell, and between the lower edge of the small through hole on a side wall of the rack cell and the lower portion of the protrusion of the finger member. If the rack cell is inserted to a bottom, the protrusion of the finger member fits the small through hole on the side of the rack cell. With such a constitution, the rack cell is prevented from withdrawing in conjunction with removal of fuels. (I.N.)

KSC technician installs rows of experiment racks in IML-1 spacelab module

Science.gov (United States)

1991-01-01

Kennedy Space Center (KSC) technician installs rows of experiment racks in the International Microgravity Laboratory 1 (IML-1) in the KSC Operations and Checkout (O and C) Bldg. The IML-1 is scheduled to fly on STS-42 in early 1992, and will turn the shuttle into a laboratory dedicated to investigating the effects of microgravity on materials and life processes. View provided by KSC with alternate number KSC-91P-169.

Rotating specimen rack repair

International Nuclear Information System (INIS)

Miller, G.E.; Rogers, P.J.; Nabor, W.G.; Bair, H.

1984-01-01

In 1980, an operator at the UCI TRIGA Reactor noticed difficulties with the rotation of the specimen rack. Investigations showed that the drive bearing in the rack had failed and allowed the bearings to enter the rack. After some time of operation in static mode it was decided that installation of a bearing substitute - a graphite sleeve - would be undertaken. Procedures were written and approved for removal of the rack, fabrication and installation of the sleeve, and re-installation of the rack. This paper describes these procedures in some detail. Detailed drawings of the necessary parts may be obtained from the authors

Arabidopsis scaffold protein RACK1A modulates rare sugar D-allose regulated gibberellin signaling.

Science.gov (United States)

Fennell, Herman; Olawin, Abdulquadri; Mizanur, Rahman M; Izumori, Ken; Chen, Jin-Gui; Ullah, Hemayet

2012-11-01

As energy sources and structural components, sugars are the central regulators of plant growth and development. In addition to the abundant natural sugars in plants, more than 50 different kinds of rare sugars exist in nature, several of which show distinct roles in plant growth and development. Recently, one of the rare sugars, D-allose, an epimer of D-glucose at C3, is found to suppress plant hormone gibberellin (GA) signaling in rice. Scaffold protein RACK1A in the model plant Arabidopsis is implicated in the GA pathway as rack1a knockout mutants show insensitivity to GA in GA-induced seed germination. Using genetic knockout lines and a reporter gene, the functional role of RACK1A in the D-allose pathway was investigated. It was found that the rack1a knockout seeds showed hypersensitivity to D-allose-induced inhibition of seed germination, implicating a role for RACK1A in the D-allose mediated suppression of seed germination. On the other hand, a functional RACK1A in the background of the double knockout mutations in the other two RACK1 isoforms, rack1b/rack1c, showed significant resistance to the D-allose induced inhibition of seed germination. The collective results implicate the RACK1A in the D-allose mediated seed germination inhibition pathway. Elucidation of the rare sugar signaling mechanism will help to advance understanding of this less studied but important cellular signaling pathway.

Foundations of topological racks and quandles

OpenAIRE

Mohamed Moutuou, El-Kaioum; Elhamdadi, Mohamed

2016-01-01

We give a foundational account on topological racks and quandles. Specifically, we define the notions of ideals, kernels, units, and inner automorphism group in the context of topological racks. Further, we investigate topological rack modules and principal rack bundles. Central extensions of topological racks are then introduced providing a first step towards a general continuous cohomology theory for topological racks and quandles

Laboratory racks are installed in the MPLM Leonardo

Science.gov (United States)

2000-01-01

In the Space Station Processing Facility, another laboratory rack is placed on the arm of the Rack Insertion Unit to lift it to the workstand height of the Multi-Purpose Logistics Module Leonardo (not seen). The MPLM will transport laboratory racks filled with equipment, experiments and supplies to and from the International Space Station aboard the Space Shuttle. Leonardo will be launched for the first time March 1, 2001, on Shuttle mission STS-102. On that flight, Leonardo will be filled with equipment and supplies to outfit the U.S. laboratory module, being carried to the ISS on the Jan. 19, 2001, launch of STS-98.

Design Features and Capabilities of the First Materials Science Research Rack

Science.gov (United States)

Pettigrew, P. J.; Lehoczky, S. L.; Cobb, S. D.; Holloway, T.; Kitchens, L.

2003-01-01

The First Materials Science Research Rack (MSRR-1) aboard the International Space Station (ISS) will offer many unique capabilities and design features to facilitate a wide range of materials science investigations. The initial configuration of MSRR-1 will accommodate two independent Experiment Modules (EMS) and provide the capability for simultaneous on-orbit processing. The facility will provide the common subsystems and interfaces required for the operation of experiment hardware and accommodate telescience capabilities. MSRR1 will utilize an International Standard Payload Rack (ISPR) equipped with an Active Rack Isolation System (ARIS) for vibration isolation of the facility.

Development of a cosmic rack for characterization of RPCs

International Nuclear Information System (INIS)

Sehgal, S.T.; Pant, L.M.

2011-01-01

A newly designed cosmic rack has been commissioned this year in the RPC Lab., in NPD-BARC. The rack consists of nine shelves each providing a clear area of 160 cm x 225 cm. Each of the shelf is separated by a distance of 30 cm, providing sufficient distance for fast electronics to respond and also providing an easy access for loading and removing the RPCs. The total height of the cosmic rack is 2.8 metres. A typical fully integrated RPCs covers an approximate area of 2 m 2 and weighs about 60-70 kg. The rack has been basically designed, keeping in mind the varied requirements as regards to the RPCs based current and futuristic programmes which are listed as follows: 1. Testing of large area trapezoidal bakelite gas-gaps and RPCs for the CMS experiment, keeping in mind the production rate of five RPCs per month. 2. The proposed muon tomography programme with 1m x 1m glass RPCs and 3. Characterization of glass RPCs (1m x 2m) for the INO experiment in near future

The ISS Fluids Integrated Rack (FIR): a Summary of Capabilities

Science.gov (United States)

Gati, F.; Hill, M. E.

2002-01-01

The Fluids Integrated Rack (FIR) is a modular, multi-user scientific research facility that will fly in the U.S. laboratory module, Destiny, of the International Space Station (ISS). The FIR will be one of the two racks that will make up the Fluids and Combustion Facility (FCF) - the other being the Combustion Integrated Rack (CIR). The ISS will provide the FCF with the necessary resources, such as power and cooling. While the ISS crew will be available for experiment operations, their time will be limited. The FCF is, therefore, being designed for autonomous operations and remote control operations. Control of the FCF will be primarily through the Telescience Support Center (TSC) at the Glenn Research Center. The FCF is being designed to accommodate a wide range of combustion and fluids physics experiments within the ISS resources and constraints. The primary mission of the FIR, however, is to accommodate experiments from four major fluids physics disciplines: Complex Fluids; Multiphase Flow and Heat Transfer; Interfacial Phenomena; and Dynamics and Stability. The design of the FIR is flexible enough to accommodate experiments from other science disciplines such as Biotechnology. The FIR flexibility is a result of the large volume dedicated for experimental hardware, easily re-configurable diagnostics that allow for unique experiment configurations, and it's customizable software. The FIR will utilize six major subsystems to accommodate this broad scope of fluids physics experiments. The major subsystems are: structural, environmental, electrical, gaseous, command and data management, and imagers and illumination. Within the rack, the FIR's structural subsystem provides an optics bench type mechanical interface for the precise mounting of experimental hardware; including optical components. The back of the bench is populated with FIR avionics packages and light sources. The interior of the rack is isolated from the cabin through two rack doors that are hinged near

Casimir rack and pinion as a miniaturized kinetic energy harvester

Science.gov (United States)

Miri, MirFaez; Etesami, Zahra

2016-08-01

We study a nanoscale machine composed of a rack and a pinion with no contact, but intermeshed via the lateral Casimir force. We adopt a simple model for the random velocity of the rack subject to external random forces, namely, a dichotomous noise with zero mean value. We show that the pinion, even when it experiences random thermal torque, can do work against a load. The device thus converts the kinetic energy of the random motions of the rack into useful work.

Study and project of the new rack with boron for storage of fuel elements burned in the IEA-R1 research reactor

International Nuclear Information System (INIS)

Rodrigues, Antonio Carlos Iglesias; Madi Filho, Tufic; Silva, Davilson Gomes da

2017-01-01

The IEA-R1 research reactor works 40h weekly with 4.5 Mw power. The storage rack for spent fuel elements has less than half of its initial capacity. Under these conditions (current conditions of reactor operation 32h weekly will have 3 spend fuel by year, then, approximately 3 utilization rate Positions/year). Thus, we will have only about six years of capacity for storage. Whereas the desired service life of the IEA-R1 is at least another 20 years, it will be necessary to increase the storage capacity of spent fuel. Hence, it is necessary to double the wet storage capacity (storage in the IEA-R1 reactor's pool). After reviewing the literature about materials available for use in the construction of the new storage rack with absorber of neutrons, the BoralcanTM (manufactured by 3TMhis) was chosen due to its properties. This work presents studies: (a) for the construction of new storages racks with double of the current capacity using the same place of current storages racks and (b) criticality analysis using the MCNP-5 code. Two American Nuclear Data Library were used: ENDF / B-VI and ENDF / B-VII, and the results obtained for each data bases were compared. These analyzes confirm the possibility of doubling the storage capacity of fuel elements burned in the same place occupied by the current storage rack attending to the IEA-R1 reactor needs and attending the safety requirements according to the National Nuclear Energy Commission - CNEN and the International Atomic Energy Agency (IAEA). To calculate the k eff were considered new fuel elements (maximum possible reactivity) used in full charge of the storage rack. With the results obtained in the simulation we can conclude that doubling the amount of racks for spent fuel elements are complied with safety limits established in the IAEA standards and CNEN of criticality (keff < 0.95). (author)

Study and project of the new rack with boron for storage of fuel elements burned in the IEA-R1 research reactor

Energy Technology Data Exchange (ETDEWEB)

Rodrigues, Antonio Carlos Iglesias; Madi Filho, Tufic; Silva, Davilson Gomes da, E-mail: acirodri@ipen.br, E-mail: tmfilho@usp.br, E-mail: dgsilva@ipen.br [Instituto de Pesquisas Energéticas e Nucleares (IPEN/CNEN-SP), São Paulo, SP (Brazil)

2017-07-01

The IEA-R1 research reactor works 40h weekly with 4.5 Mw power. The storage rack for spent fuel elements has less than half of its initial capacity. Under these conditions (current conditions of reactor operation 32h weekly will have 3 spend fuel by year, then, approximately 3 utilization rate Positions/year). Thus, we will have only about six years of capacity for storage. Whereas the desired service life of the IEA-R1 is at least another 20 years, it will be necessary to increase the storage capacity of spent fuel. Hence, it is necessary to double the wet storage capacity (storage in the IEA-R1 reactor's pool). After reviewing the literature about materials available for use in the construction of the new storage rack with absorber of neutrons, the BoralcanTM (manufactured by 3TMhis) was chosen due to its properties. This work presents studies: (a) for the construction of new storages racks with double of the current capacity using the same place of current storages racks and (b) criticality analysis using the MCNP-5 code. Two American Nuclear Data Library were used: ENDF / B-VI and ENDF / B-VII, and the results obtained for each data bases were compared. These analyzes confirm the possibility of doubling the storage capacity of fuel elements burned in the same place occupied by the current storage rack attending to the IEA-R1 reactor needs and attending the safety requirements according to the National Nuclear Energy Commission - CNEN and the International Atomic Energy Agency (IAEA). To calculate the k{sub eff} were considered new fuel elements (maximum possible reactivity) used in full charge of the storage rack. With the results obtained in the simulation we can conclude that doubling the amount of racks for spent fuel elements are complied with safety limits established in the IAEA standards and CNEN of criticality (keff < 0.95). (author)

Flow in data racks

Directory of Open Access Journals (Sweden)

Manoch Lukáš

2014-03-01

Full Text Available This paper deals with the flow in data racks. The aim of this work is to find a new arrangement of elements regulating the flow in the data rack so that the aerodynamic losses and the recirculation zones were minimized. The main reason for solving this problem is to reduce the costs of data racks cooling. Another problem to be solved is a reverse flow in the servers, thus not cooled, occuring due to the underpressure in the recirculation zones. In order to solve the problem, the experimental and numerical model of 27U data rack fitted with 10 pieces of server models with a total input of 10 kW was created. Different configurations of layout of elements affecting the flow in the inlet area of the data rack were compared. Depending on the results achieved, design solutions for the improvement of existing solutions were adopted and verified by numerical simulations.

Link invariants from finite Coxeter racks

OpenAIRE

Nelson, Sam; Wieghard, Ryan

2008-01-01

We study Coxeter racks over $\\mathbb{Z}_n$ and the knot and link invariants they define. We exploit the module structure of these racks to enhance the rack counting invariants and give examples showing that these enhanced invariants are stronger than the unenhanced rack counting invariants.

Microgravity Disturbance Predictions in the Combustion Integrated Rack

Science.gov (United States)

Just, M.; Grodsinsky, Carlos M.

2002-01-01

This paper will focus on the approach used to characterize microgravity disturbances in the Combustion Integrated Rack (CIR), currently scheduled for launch to the International Space Station (ISS) in 2005. Microgravity experiments contained within the CIR are extremely sensitive to vibratory and transient disturbances originating on-board and off-board the rack. Therefore, several techniques are implemented to isolate the critical science locations from external vibration. A combined testing and analysis approach is utilized to predict the resulting microgravity levels at the critical science location. The major topics to be addressed are: 1) CIR Vibration Isolation Approaches, 2) Disturbance Sources and Characterization, 3) Microgravity Predictive Modeling, 4) Science Microgravity Requirements, 6) Microgravity Control, and 7) On-Orbit Disturbance Measurement. The CIR is using the Passive Rack Isolation System (PaRIS) to isolate the rack from offboard rack disturbances. By utilizing this system, CIR is connected to the U.S. Lab module structure by either 13 or 14 umbilical lines and 8 spring / damper isolators. Some on-board CIR disturbers are locally isolated by grommets or wire ropes. CIR's environmental and science on board support equipment such as air circulation fans, pumps, water flow, air flow, solenoid valves, and computer hard drives cause disturbances within the rack. These disturbers along with the rack structure must be characterized to predict whether the on-orbit vibration levels during experimentation exceed the specified science microgravity vibration level requirements. Both vibratory and transient disturbance conditions are addressed. Disturbance levels/analytical inputs are obtained for each individual disturber in a "free floating" condition in the Glenn Research Center (GRC) Microgravity Emissions Lab (MEL). Flight spare hardware is tested on an Orbital Replacement Unit (ORU) basis. Based on test and analysis, maximum disturbance level

Fuel assembly storing rack

International Nuclear Information System (INIS)

Kajimura, Haruhiko; Nakamura, Masaaki.

1997-01-01

In a nuclear fuel storage rack comprising a plurality of square-shaped rack cells arranged vertically in a lattice-like configuration, the square rack cell comprises a stainless steel having a boron content of 0.75% or less and a boron equivalent with respect to calculated thermal neutron absorbing performance of 1.0 or more, and a distance between each of the gap of the square rack cells in adjacent with each other satisfies a predetermined condition. One example of the content is that B is from 0.05 to 0.75%, Gd is from 0.05 to 1.50%, C is 0.03% or less, Si is 1.0% or less, Mn is from 0.1 to 2.0%, P is 0.03% or less, S is 0.01% or less, Cr is from 18 to 26%, Ni is from 7 to 22% and Al is 0.1% or less. The distance between the rack cells can be reduced by using a material improved with thermal neutron absorbing performance by determining the boron equivalent to a predetermined value or more and with less B-content and good fabricability. In addition, the size of the rack cell itself can be reduced. This can greatly reduce the nuclear fuel storage area. (I.S.)

21 CFR 886.1750 - Skiascopic rack.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Skiascopic rack. 886.1750 Section 886.1750 Food... DEVICES OPHTHALMIC DEVICES Diagnostic Devices § 886.1750 Skiascopic rack. (a) Identification. A skiascopic rack is a device that is a rack and a set of attached ophthalmic lenses of various dioptric strengths...

Arbitrary vehicle steering characteristics with changing ratio rack and pinion transmission

Directory of Open Access Journals (Sweden)

András G Bendefy

2015-12-01

Full Text Available In order to achieve arbitrary steering characteristics at vehicles, a steering mechanism was developed, in which changing ratio rack and pinion connections have been applied. In contrary to a regular steering mechanism where only a single rack is used, two racks were applied in order to make arbitrary characteristics possible. The turning wheel’s required motion functions had to be defined first, thereafter could we determine the changing ratio rack and pinion geometry which produces this motion. First, a simplified two-dimensional mockup was created in order to study the difficulties and possibilities of a real construction. Later, a fully functional assembly was designed and manufactured to make further experiments possible.

First Materials Science Research Facility Rack Capabilities and Design Features

Science.gov (United States)

Cobb, S.; Higgins, D.; Kitchens, L.; Curreri, Peter (Technical Monitor)

2002-01-01

The first Materials Science Research Rack (MSRR-1) is the primary facility for U.S. sponsored materials science research on the International Space Station. MSRR-1 is contained in an International Standard Payload Rack (ISPR) equipped with the Active Rack Isolation System (ARIS) for the best possible microgravity environment. MSRR-1 will accommodate dual Experiment Modules and provide simultaneous on-orbit processing operations capability. The first Experiment Module for the MSRR-1, the Materials Science Laboratory (MSL), is an international cooperative activity between NASA's Marshall Space Flight Center (MSFC) and the European Space Agency's (ESA) European Space Research and Technology Center (ESTEC). The MSL Experiment Module will accommodate several on-orbit exchangeable experiment-specific Module Inserts which provide distinct thermal processing capabilities. Module Inserts currently planned for the MSL are a Quench Module Insert, Low Gradient Furnace, and a Solidification with Quench Furnace. The second Experiment Module for the MSRR-1 configuration is a commercial device supplied by MSFC's Space Products Development (SPD) Group. Transparent furnace assemblies include capabilities for vapor transport processes and annealing of glass fiber preforms. This Experiment Module is replaceable on-orbit. This paper will describe facility capabilities, schedule to flight and research opportunities.

Spent fuel storage rack

International Nuclear Information System (INIS)

Kurokawa, Hideaki; Kumagaya, Naomi; Oda, Masashi; Matsuda, Masami; Maruyama, Hiromi; Yamanaka, Tsuneyasu.

1997-01-01

The structure of a spent fuel storage rack is determined by the material, thickness, size of square cylindrical tubes (the gap between spent fuel assemblies and the square cylindrical tubes) and pitch of the arrangement (the gap between each of the square cylindrical tubes). In the present invention, the thickness and the pitch of the arrangement of the square tubes are optimized while evaluating subcriticality. Namely, when the sum of the thickness of the water gap at the outer side (the pitch of arrangement of the cylindrical tubes) and the thickness of the cylindrical tubes is made constant, the storage rack is formed by determining the thickness of the cylindrical tubes which is smaller than the optimum value among the combination of the thickness of the water gap at the outer side and that of the cylindrical tube under the effective multiplication factor to be performed. Then, the weight of the rack can be reduced, and the burden of the load on the bottom of the pool can be reduced. Further, the amount of the constitutional materials of the rack itself can be reduced thereby capable of reducing the cost for the materials of the rack. (T.M.)

Rack Protection Monitor - A Simple System

International Nuclear Information System (INIS)

Orr, S.

1997-12-01

The Rack Protection Monitor is a simple, fail-safe device to monitor smoke, temperature and ventilation sensors. It accepts inputs from redundant sensors and has a hardwired algorithm to prevent nuisance power trips due to random sensor failures. When a sensor is triggered the Rack Protection Monitor latches and annunicates the alarm. If another sensor is triggered, the Rack Protection Monitor locally shuts down the power to the relay rack and sends alarm to central control

Hydrodynamics induced vibration to trash-racks

International Nuclear Information System (INIS)

Sadrnejad, A.

2002-01-01

In conventional power plants trash-racks are provided at the intakes to protect the turbines. In pumped storage plants, the draft tube or tailrace must also have trash-racks to protect the units while pumping. Because the loads believed to cause many failures of trash-racks are dynamic in nature, it is important to understand the dynamic characteristics of trash-racks structures in general and a single rack in particular. The classical added-mass solution structure-fluid dynamic interaction is known as an approximate solution procedure. An accurate added-mass approach mixed with implementation in finite element framework is proposed. In this proposal, experimental conclusions, supported by theory, led to presentation of more accurate results in vibration of trash-racks. This numerical solution as a powerful method to solve such a complex problem can be employed to carry out dynamic characteristics of these structures while vibrating in water

Storage racks for spent fuels

International Nuclear Information System (INIS)

Inoue, Tatsumi.

1983-01-01

Purpose: To provide a storage rack which is light in weight, excellent in constructing performance, earthquake proof and allowable for thermal displacement. Constitution: The rack frame is constituted by disposing mounting seat plates at the legs of profiled-steel post members on a rack-mounting plate as a mounting seat by way of mounting liner plates and then weld-joining each of upper, medium and lower beam members and truss members of the profiled-steel posts by the use of connecting plates. Guide plates are laid transversely and joined onto each of the thus formed upper, medium and lower stage frames. Since apertures for mounting guide tubes are opened to each of the guide plates at a predetermined pitch, the storage rack unit is constituted by mounting guide tubes to the apertures. Then, the storage rack is mounted by means of slide keys to the mounting plates where slight amount of sliding or thermal displacement can be absorbed. (Horiuchi, T.)

First Materials Science Research Rack Capabilities and Design Features

Science.gov (United States)

Schaefer, D.; King, R.; Cobb, S.; Whitaker, Ann F. (Technical Monitor)

2001-01-01

The first Materials Science Research Rack (MSRR-1) will accommodate dual Experiment Modules (EM's) and provide simultaneous on-orbit processing operations capability. The first international Materials Science Experiment Module for the MSRR-1 is an international cooperative research activity between NASA's Marshall Space Flight Center (MSFC) and the European Space Agency's (ESA) European Space Research and Technology Center. (ESTEC). This International Standard Payload Rack (ISPR) will contain the Materials Science Laboratory (MSL) developed by ESA as an Experiment Module. The MSL Experiment Module will accommodate several on-orbit exchangeable experiment-specific Module Inserts. Module Inserts currently planned are a Quench Module Insert, Low Gradient Furnace, Solidification with Quench Furnace, and Diffusion Module Insert. The second Experiment Module for the MSRR-1 configuration is a commercial device supplied by MSFC's Space Products Department (SPD). It includes capabilities for vapor transport processes and liquid metal sintering. This Experiment Module will be replaced on-orbit with other NASA Materials Science EMs.

40 CFR 63.422 - Standards: Loading racks.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 9 2010-07-01 2010-07-01 false Standards: Loading racks. 63.422....422 Standards: Loading racks. (a) Each owner or operator of loading racks at a bulk gasoline terminal... facility” used in § 60.502 of this chapter means the loading racks that load gasoline cargo tanks at the...

10 CFR 36.35 - Source rack protection.

Science.gov (United States)

2010-01-01

... 10 Energy 1 2010-01-01 2010-01-01 false Source rack protection. 36.35 Section 36.35 Energy NUCLEAR... Requirements for Irradiators § 36.35 Source rack protection. If the product to be irradiated moves on a product conveyor system, the source rack and the mechanism that moves the rack must be protected by a barrier or...

Seismic analysis of freestanding fuel racks

International Nuclear Information System (INIS)

Gilmore, C.B.

1982-01-01

This paper presents a nonlinear transient dynamic time-history analysis of freestanding spent fuel storage racks subjected to seismic excitation. This type of storage rack is structurally unrestrained and submerged in water in the spent fuel pool of a nuclear power complex, holds (spent) fuel assemblies which have been removed from the reactor core. Nonlinearities in the fuel rack system include impact between the fuel assembly and surrounding cell due to clearances between them, friction due to sliding between the fuel rack support structure and spent fuel pool floor, and the lift-off of the fuel rack support structure from the spent fuel pool floor. The analysis of the fuel rack system includes impacting due to gap closures, energy losses due to impacting bodies, Coulomb damping between sliding surfaces, and hydrodynamic mass effects. Acceleration time history excitation development is discussed. Modeling considerations, such as the initial status of nonlinear elements, number of mode shapes to include in the analysis, modal damping, and integration time-step size are presented. The response of the fuel rack subjected to two-dimensional seismic excitation is analyzed by the modal superposition method, which has resulted in significant computer cost savings when compared to that of direct integration

40 CFR 63.1105 - Transfer racks.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 10 2010-07-01 2010-07-01 false Transfer racks. 63.1105 Section 63... Technology Standards § 63.1105 Transfer racks. (a) Design requirements. The owner or operator shall equip each transfer rack with one of the control options listed in paragraphs (a)(1) through (4) of this...

21 CFR 882.4215 - Clip rack.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Clip rack. 882.4215 Section 882.4215 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES NEUROLOGICAL DEVICES Neurological Surgical Devices § 882.4215 Clip rack. (a) Identification. A clip rack is a...

Development of seismic design method for free standing rack and applicability to Japanese nuclear power plant

International Nuclear Information System (INIS)

Takaki, Yu; Taniguchi, Katsuhiko; Kishimoto, Junichi; Iwasaki, Akihisa; Nekomoto, Yoshitsugu; Kuga, Tohru; Kameyama, Masashi

2017-01-01

Free standing racks which are not anchored to the pool floor nor walls have never been adopted in Japan. Under an earthquake, behaviors of free standing racks are nonlinear and involve a complex combination of motions (sliding, rocking, and twisting) and impacts between a fuel assembly and the fuel cell walls and between a pit floor and rack pedestals. To predict a seismic response of free standing racks, the seismic analysis requires careful considerations of these complex phenomena (sliding, rocking, and twisting), fluid coupling effects and frictional effects. We carried out seismic experiments on the full-scale rack model in both water and dry conditions and obtained the fundamental data about behavior of free standing racks (sliding, and rocking motions). We have developed the nonlinear dynamic analysis method to predict seismic response of free standing racks utilizing the full-scale test result and verified the analysis evaluation method of free standing rack by comparison between analysis results and experimental data. Furthermore, we applied the seismic design method to the free standing rack in the Japanese nuclear plant (Mihama nuclear power station Unit 3), and verified that the free standing rack was applicable to Japanese nuclear plant. (author)

Seismic analysis of spent nuclear fuel storage racks

International Nuclear Information System (INIS)

Shah, S.J.; Biddle, J.R.; Bennett, S.M.; Schechter, C.B.; Harstead, G.A.; Marquet, F.

1996-01-01

In many nuclear power plants, existing storage racks are being replaced with high-density racks to accommodate the increasing inventory of spent fuel. In the hypothetical design considered here, the high-density arrangement of fuel assemblies, or consolidated fuel canisters, is accomplished through the use of borated stainless steel (BSS) plates acting as neutron absorbers. No structural benefit from the BSS is assumed. This paper describes the methods used to perform seismic analysis of high density spent fuel storage racks. The sensitivity of important parameters such as the effect of variation of coefficients of friction between the rack legs and the pool floor and fuel loading conditions (consolidated and unconsolidated) are also discussed in the paper. Results of this study are presented. The high-density fuel racks are simply supported by the pool floor with no structural connections to adjacent racks or to the pool walls or floor. Therefore, the racks are free standing and may slide and tip. Several time history, nonlinear, seismic analyses are required to account for variations in the coefficient of friction, rack loading configuration, and the type of the seismic event. This paper presents several of the mathematical models usually used. Friction cannot be precisely predicted, so a range of friction coefficients is assumed. The range assumed for the analysis is 0.2 to 0.8. A detailed model representing a single rack is used to evaluate the 3-D loading effects. This model is a controlling case for the stress analysis. A 2-D multi-rack model representing a row of racks between the spent fuel pool walls is used to evaluate the change in gaps between racks. The racks are normally analyzed for the fuel loading conditions of consolidated, full, empty, and half-loaded with fuel assemblies

High density fuel storage rack

International Nuclear Information System (INIS)

Zezza, L.J.

1980-01-01

High storage density for spent nuclear fuel assemblies in a pool achieved by positioning fuel storage cells of high thermal neutron absorption materials in an upright configuration in a rack. The rack holds the cells at required pitch. Each cell carries an internal fuel assembly support, and most cells are vertically movable in the rack so that they rest on the pool bottom. Pool water circulation through the cells and around the fuel assemblies is permitted by circulation openings at the top and bottom of the cells above and below the fuel assemblies

Criticality and Its Uncertainty Analysis of Spent Fuel Storage Rack for Research Reactor

International Nuclear Information System (INIS)

Han, Tae Young; Park, Chang Je; Lee, Byung Chul

2011-01-01

For evaluating the criticality safety of spent fuel storage rack in an open pool type research reactor, a permissible upper limit of criticality should be determined. It can be estimated from the criticality upper limit presented by the regulatory guide and an uncertainty of criticality calculation. In this paper, criticalities for spent fuel storage rack are carried out at various conditions. The calculation uncertainty of MCNP system is evaluated from the calculation results for the benchmark experiments. Then, the upper limit of criticality is determined from the uncertainties and the calculated criticality of the spent fuel storage rack is evaluated

Seismic behavior of steel storage pallet racking systems

CERN Document Server

Castiglioni, Carlo Andrea

2016-01-01

This book presents the main outcomes of the first European research project on the seismic behavior of adjustable steel storage pallet racking systems. In particular, it describes a comprehensive and unique set of full-scale tests designed to assess such behavior. The tests performed include cyclic tests of full-scale rack components, namely beam-to-upright connections and column base connections; static and dynamic tests to assess the friction factor between pallets and rack beams; full-scale pushover and pseudodynamic tests of storage racks in down-aisle and cross-aisle directions; and full-scale dynamic tests on two-bay, three-level rack models. The implications of the findings of this extensive testing regime on the seismic behavior of racking systems are discussed in detail, highlighting e.g. the confirmation that under severe dynamic conditions “sliding” is the main factor influencing rack response. This work was conceived during the development of the SEISRACKS project. Its outcomes will contribute...

Storage rack for holding spent fuel elements from nuclear power plants

International Nuclear Information System (INIS)

Krieger, F.

1978-01-01

In the fuel rack containing a great number of compartments with square cross-sections, the structural elements required by the system are statically designed in such a way, that optimal utilization of space as well as shielding of the compartments with respect to each other is guaranteed. In order to achieve this the compartments may be formed by profiled sheets having got trapezoidal edges taken off. Two sheets, each running parallel with respect to each other, form a double shell. The compartments are formed by another double shell, also consisting of two sheets and lying mirror-inverted with respect to the first shell touching this one. (DG) [de

Modular nuclear fuel assembly rack

International Nuclear Information System (INIS)

Davis, C.J.

1982-01-01

A modular nuclear fuel assembly rack constructed of an array of identical cells, each cell constructed of a plurality of identical flanged plates. The unique assembly of the plates into a rigid rack provides a cellular compartment for nuclear fuel assemblies and a cavity between the cells for accepting neutron absorbing materials thus allowing a closely spaced array. The modular rack size can be easily adapted to conform with available storage space. U-shaped flanges at the edges of the plates are nested together at the intersection of four cells in the array. A bar is placed at the intersection to lock the cells together

Fuel consumption impacts of auto roof racks

International Nuclear Information System (INIS)

Chen, Yuche; Meier, Alan

2016-01-01

The after-market roof rack is one of the most common components attached to a vehicle for carrying over-sized items, such as bicycles and skis. It is important to understand these racks’ fuel consumption impacts on both individual vehicles and the national fleet because they are widely used. We estimate the national fuel consumption impacts of roof racks using a bottom-up approach. Our model incorporates real-world data and vehicle stock information to enable assessing fuel consumption impacts for several categories of vehicles, rack configurations, and usage conditions. In addition, the model draws on two new data-gathering techniques, on-line forums and crowd-sourcing. The results show that nationwide, roof racks are responsible for 0.8‰ of light duty vehicle fuel consumption in 2015, corresponding to 100 million gallons of gasoline per year. Sensitivity analyses show that results are most sensitive to the fraction of vehicles with installed roof racks but carrying no equipment. The aerodynamic efficiency of typical roof racks can be greatly improved and reduce individual vehicle fuel consumption; however, government policies to minimize extensive driving with empty racks—if successful—could save more fuel nationally. - Highlights: •First estimate of national energy impacts of auto roof racks—about 1‰. •A bottom-up approach reveals details of the fuel consumption penalty caused by racks. •Two novel data collection techniques, on-line forums and crowd-sourcing, improve estimate. •Technical and behavioral policies could significantly cut fuel penalties from roof racks.

RackSaver neutron absorbing device development and testing

International Nuclear Information System (INIS)

Lambert, R.; O'Leary, P.; Roberts, P.

1996-01-01

Siemens Power Corporation (SPC), in cooperation with the Electric Power Research Institute (EPRI), has developed the RackSaver neutron absorbing insert. The RackSaver insert can be installed onto spent nuclear fuel assemblies to replace deteriorating Boraflex neutron absorbing material installed in some spent-fuel storage racks. This paper describes results of a development and in-pool demonstration program performed to support potential utilization of the RackSaver neutron absorbing insert by affected utilities. The program objective was to advance the RackSaver concept into a field-demonstrated product. This objective was accomplished through three phases: design, licensing and criticality evaluations, and demonstration testing

Compact fuel storage rack for fuel pools

International Nuclear Information System (INIS)

Parras, F.; Louvat, J.P.

1986-01-01

ETS LEMER and FRAMATOME propose a new compact storage rack. This rack permits a considerable increase of the storage capacity of cooling pools. A short description of the structure and the components is presented, to propose racks that are: . Inalterable, . Compact, . Insensitive to earthquakes. Installation in pools already in operation is simplified by their light structure and the bearing device [fr

From racks to pointed Hopf algebras

OpenAIRE

Andruskiewitsch, Nicolás; Graña, Matı́as

2003-01-01

A fundamental step in the classification of finite-dimensional complex pointed Hopf algebras is the determination of all finite-dimensional Nichols algebras of braided vector spaces arising from groups. The most important class of braided vector spaces arising from groups is the class of braided vector spaces (CX, c^q), where C is the field of complex numbers, X is a rack and q is a 2-cocycle on X with values in C^*. Racks and cohomology of racks appeared also in the work of topologists. This...

Spent fuel storage rack for atomic power plant

International Nuclear Information System (INIS)

Kodama, Tatemitsu.

1981-01-01

Purpose: To flexibly cope with the changes in the size and shape of spent fuel storage containers by placing a number of independently-constructed rack cells in a rack frame in such a manner that the guide support members of the storage rack, mounted on each rack cell may be replaced. Constitution: Independently-constructed rack cells are inserted from above into a rack frame rigidly installed on the bottom of a water pool. Each cell is produced by welding, has a handling head mounted at the top, and guide support members made of three replaceable guide tubes are mounted with bolts. If the size and the shape of the containers are altered, this configuration can easily cope with the new container shape by merely having the guide tubes replaced, without adversely affecting other cells and without necessitating draining of the water in the pool. (Yoshino, Y.)

RACK1, A Multifaceted Scaffolding Protein: Structure and Function

LENUS (Irish Health Repository)

Adams, David R

2011-10-06

Abstract The Receptor for Activated C Kinase 1 (RACK1) is a member of the tryptophan-aspartate repeat (WD-repeat) family of proteins and shares significant homology to the β subunit of G-proteins (Gβ). RACK1 adopts a seven-bladed β-propeller structure which facilitates protein binding. RACK1 has a significant role to play in shuttling proteins around the cell, anchoring proteins at particular locations and in stabilising protein activity. It interacts with the ribosomal machinery, with several cell surface receptors and with proteins in the nucleus. As a result, RACK1 is a key mediator of various pathways and contributes to numerous aspects of cellular function. Here, we discuss RACK1 gene and structure and its role in specific signaling pathways, and address how posttranslational modifications facilitate subcellular location and translocation of RACK1. This review condenses several recent studies suggesting a role for RACK1 in physiological processes such as development, cell migration, central nervous system (CN) function and circadian rhythm as well as reviewing the role of RACK1 in disease.

Server rack for improved data center management

Science.gov (United States)

Bermudez Rodriguez, Sergio A.; Hamann, Hendrik F.; Wehle, Hans-Dieter

2018-01-09

Methods and systems for data center management include collecting sensor data from one or more sensors in a rack; determining a location and identifying information for each asset in the rack using a set of asset tags associated with respective assets; communicating the sensor and asset location to a communication module; receiving an instruction from the communication module; and executing the received instruction to change a property of the rack.

Framatome offers new high density Cadminox racks

International Nuclear Information System (INIS)

Anon.

1985-01-01

Framatome have developed a new material called Cadminox for use in high density spent fuel storage racks. It is claimed that Cadminox will remain stable stable in pond storage when racks submerged in boronated water are irradiated by the spent fuel they contain. A brief description of the storage module is given, including the aseismic bearing device which minimises loads on pond walls, racks and fuel assemblies. (UK)

40 CFR 63.650 - Gasoline loading rack provisions.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 10 2010-07-01 2010-07-01 false Gasoline loading rack provisions. 63... loading rack provisions. (a) Except as provided in paragraphs (b) through (c) of this section, each owner or operator of a Group 1 gasoline loading rack classified under Standard Industrial Classification...

Rack assembly for mounting solar modules

Science.gov (United States)

Plaisted, Joshua Reed; West, Brian

2010-12-28

A rack assembly is provided for mounting solar modules over an underlying body. The rack assembly may include a plurality of rail structures that are arrangeable over the underlying body to form an overall perimeter for the rack assembly. One or more retention structures may be provided with the plurality of rail structures, where each retention structure is configured to support one or more solar modules at a given height above the underlying body. At least some of the plurality of rail structures are adapted to enable individual rail structures o be sealed over the underlying body so as to constrain air flow underneath the solar modules. Additionally, at least one of (i) one or more of the rail structures, or (ii) the one or more retention structures are adjustable so as to adapt the rack assembly to accommodate solar modules of varying forms or dimensions.

Refurbishment of the Oregon State University rotating rack

International Nuclear Information System (INIS)

Higginbotham, J.F.

1991-01-01

TRIGA reactors have experienced operational difficulties with the rotating racks used for sample irradiation. The most common problem occurs when the rack seizes, and the corrective action taken is replacement of the rack assembly. This paper describes the symptoms leading to rack failure and a refurbishment procedure to correct the problem without replacing the rack at the Oregon State University TRIGA Reactor (OSTR) Facility. This procedure was accomplished with extraordinary results from an operational and a radiation protection standpoint. The refurbishment has extended the useful life of this reactor facility with minimal financial impact. Given the declining number of university-based research reactors, it is in the nation's best interest to maintain the currently operating research reactor facilities, and the described procedure can aid in achieving that goal

RACK(1) to the future - a historical perspective

LENUS (Irish Health Repository)

Ron, Dorit

2013-08-01

This perspective summarises the first and long overdue RACK1 meeting held at the University of Limerick, Ireland, May 2013, in which RACK1’s role in the immune system, the heart and the brain were discussed and its contribution to disease states such as cancer, cardiac hypertrophy and addiction were described. RACK1 is a scaffolding protein and a member of the WD repeat family of proteins. These proteins have a unique architectural assembly that facilitates protein anchoring and the stabilisation of protein activity. A large body of evidence is accumulating which is helping to define the versatile role of RACK1 in assembling and dismantling complex signaling pathways from the cell membrane to the nucleus in health and disease. In this commentary, we first provide a historical perspective on RACK1. We also address many of the pertinent and topical questions about this protein such as its role in transcription, epigenetics and translation, its cytoskeletal contribution and the merits of targeting RACK1 in disease.

RACK1-mediated translation control promotes liver fibrogenesis

Energy Technology Data Exchange (ETDEWEB)

Liu, Min; Peng, Peike; Wang, Jiajun [Department of Biochemistry and Molecular Biology, School of Basic Medical Sciences, Fudan University, Shanghai 200032 (China); Wang, Lan; Duan, Fangfang [Institute of Biomedical Science, Fudan University, Shanghai 200032 (China); Jia, Dongwei, E-mail: jiadongwei@fudan.edu.cn [Department of Biochemistry and Molecular Biology, School of Basic Medical Sciences, Fudan University, Shanghai 200032 (China); Ruan, Yuanyuan, E-mail: yuanyuanruan@fudan.edu.cn [Department of Biochemistry and Molecular Biology, School of Basic Medical Sciences, Fudan University, Shanghai 200032 (China); Gu, Jianxin [Department of Biochemistry and Molecular Biology, School of Basic Medical Sciences, Fudan University, Shanghai 200032 (China); Institute of Biomedical Science, Fudan University, Shanghai 200032 (China)

2015-07-31

Activation of quiescent hepatic stellate cells (HSCs) is the central event of liver fibrosis. The translational machinery is an optimized molecular network that affects cellular homoeostasis and diseases, whereas the role of protein translation in HSCs activation and liver fibrosis is little defined. Our previous report suggests that up-regulation of receptor for activated C-kinase 1(RACK1) in HSCs is critical for liver fibrogenesis. In this study, we found that RACK1 promoted macrophage conditioned medium (MCM)-induced assembly of eIF4F and phosphorylation of eIF4E in primary HSCs. RACK1 enhanced the translation and expression of pro-fibrogenic factors collagen 1α1, snail and cyclin E1 induced by MCM. Administration of PP242 or knock-down of eIF4E suppressed RACK1-stimulated collagen 1α1 production, proliferation and migration in primary HSCs. In addition, depletion of eIF4E attenuated thioacetamide (TAA)-induced liver fibrosis in vivo. Our data suggest that RACK1-mediated stimulation of cap-dependent translation plays crucial roles in HSCs activation and liver fibrogenesis, and targeting translation initiation could be a promising strategy for the treatment of liver fibrosis. - Highlights: • RACK1 induces the assembly of eIF4F and phosphorylation of eIF4E in primary HSCs. • RACK1 stimulates the translation of collagen 1α1, snail and cyclin E1 in HSCs. • RACK1 promotes HSCs activation via cap-mediated translation. • Depletion of eIF4E suppresses liver fibrogenesis in vivo.

RACK1-mediated translation control promotes liver fibrogenesis

International Nuclear Information System (INIS)

Liu, Min; Peng, Peike; Wang, Jiajun; Wang, Lan; Duan, Fangfang; Jia, Dongwei; Ruan, Yuanyuan; Gu, Jianxin

2015-01-01

Activation of quiescent hepatic stellate cells (HSCs) is the central event of liver fibrosis. The translational machinery is an optimized molecular network that affects cellular homoeostasis and diseases, whereas the role of protein translation in HSCs activation and liver fibrosis is little defined. Our previous report suggests that up-regulation of receptor for activated C-kinase 1(RACK1) in HSCs is critical for liver fibrogenesis. In this study, we found that RACK1 promoted macrophage conditioned medium (MCM)-induced assembly of eIF4F and phosphorylation of eIF4E in primary HSCs. RACK1 enhanced the translation and expression of pro-fibrogenic factors collagen 1α1, snail and cyclin E1 induced by MCM. Administration of PP242 or knock-down of eIF4E suppressed RACK1-stimulated collagen 1α1 production, proliferation and migration in primary HSCs. In addition, depletion of eIF4E attenuated thioacetamide (TAA)-induced liver fibrosis in vivo. Our data suggest that RACK1-mediated stimulation of cap-dependent translation plays crucial roles in HSCs activation and liver fibrogenesis, and targeting translation initiation could be a promising strategy for the treatment of liver fibrosis. - Highlights: • RACK1 induces the assembly of eIF4F and phosphorylation of eIF4E in primary HSCs. • RACK1 stimulates the translation of collagen 1α1, snail and cyclin E1 in HSCs. • RACK1 promotes HSCs activation via cap-mediated translation. • Depletion of eIF4E suppresses liver fibrogenesis in vivo

Seismic and structural analysis of high density/consolidated spent fuel storage racks

International Nuclear Information System (INIS)

Shah, S.J.; Biddle, J.R.; Bennett, S.M.; Schechter, C.B.; Harstead, G.A.; Kopecky, B.

1995-01-01

In many nuclear power plants, existing storage racks are being replaced with high-density racks to accommodate the increasing inventory of spent fuel. In the hypothetical design considered here, the high-density arrangement of fuel assemblies, or consolidated fuel canisters, is accomplished through the use of borated stainless steel (BSS) plates acting as neutron absorbers. The high-density fuel racks are simply supported by the pool floor with no structural connections to adjacent racks or to the pool walls or floor. Therefore, the racks are free standing and may slide and tip. Several time history, nonlinear, seismic analyses are required to account for variations in the coefficient of friction, rack loading configuration, ad the type of the seismic event. This paper presents several of the mathematical models usually used. The models include features to allow sliding and tipping of the racks and to represent the hydrodynamic coupling which can occur between fuel assemblies and rack cells, between adjacent racks, and between the racks and the reinforced concrete walls. A detailed model representing a single rack is used to evaluate the 3-D loading effects. This model is a controlling case for the stress analysis. A 2-D multi-rack model representing a row of racks between the spent fuel pool walls is used to evaluate the change in gaps between racks. The racks are analyzed for the fuel loading conditions of consolidated, full, empty, and half-loaded with fuel assemblies

Seismic analysis of rack structures for fuel cycle facilities

International Nuclear Information System (INIS)

Mochio, Takashi; Morooka, Akihiko; Ito, Takashi.

1987-01-01

A concept of remote maintenance using in large remote cell and rack system structure, which is now under development at high active liquid waste vitrification facility of PNC and West Germany reprocessing plant WA-350, has been adopted to reduce the radiation exposure and increase the operating efficiency. The operation of a highly efficient remote maintenance system sometimes requires the rack structures to be fairly flexible, because of the large number of loose connections and/or gapped supports and the low number of rack frames. This means that there is a possibility of severe damage occurring due to large amplitude responses during a strong earthquake. Therefore, it is very important to estimate the earthquake-resistance capacity of rack structures, including process equipment, to earthquake excitation. This paper presents an outline of a new computer code ''FRACK'' to analyze the nonlinear seismic response of a rack structure developed as a first stage in the rack system seismic research program. (author)

Storage rack for fuel cell receiving shrouds

International Nuclear Information System (INIS)

Mollon, L.

1978-01-01

Disclosed is a rack for receiving a multiplicity of vertical tubular shrouds or tubes for storing spent nuclear fuel cells. The rack comprises a plurality of horizontally reticulated frames interconnected by tension rods and spacing tubes surrounding the rods

Nanofabricated racks of aligned and anchored DNA substrates for single-molecule imaging.

Science.gov (United States)

Gorman, Jason; Fazio, Teresa; Wang, Feng; Wind, Shalom; Greene, Eric C

2010-01-19

Single-molecule studies of biological macromolecules can benefit from new experimental platforms that facilitate experimental design and data acquisition. Here we develop new strategies to construct curtains of DNA in which the molecules are aligned with respect to one another and maintained in an extended configuration by anchoring both ends of the DNA to the surface of a microfluidic sample chamber that is otherwise coated with an inert lipid bilayer. This "double-tethered" DNA substrate configuration is established through the use of nanofabricated rack patterns comprised of two distinct functional elements: linear barriers to lipid diffusion that align DNA molecules anchored by one end to the bilayer and antibody-coated pentagons that provide immobile anchor points for the opposite ends of the DNA. These devices enable the alignment and anchoring of thousands of individual DNA molecules, which can then be visualized using total internal reflection fluorescence microscopy under conditions that do not require continuous application of buffer flow to stretch the DNA. This unique strategy offers the potential for studying protein-DNA interactions on large DNA substrates without compromising measurements through application of hydrodynamic force. We provide a proof-of-principle demonstration that double-tethered DNA curtains made with nanofabricated rack patterns can be used in a one-dimensional diffusion assay that monitors the motion of quantum dot-tagged proteins along DNA.

Manufacturing and Construction of Spent Fuel Storage Rack for Research Reactor

Energy Technology Data Exchange (ETDEWEB)

Lee, Sangjin; Jung, Kwangsub; Oh, Jinho; Lee, Jongmin [KAERI, Daejeon (Korea, Republic of)

2016-05-15

The spent fuel storage rack consists of spent fuel storage racks and support frame. The spent fuel storage racks are installed in the support frame. A spent fuel storage rack consists of frame weldment and storage cell pipe assembly. Storage cell pipe assembly is mounted on the base plate of the frame weldment. The spent fuel storage rack is designed to withstand seismic load and other loads during earthquake. The structural integrity of the spent fuel storage rack is evaluated in accordance with ASME Section III, Subsection NF. Computer Code used for this analysis is ANSYS version 14.0.0. Dead load and seismic load is considered in load condition and hydrodynamic mass is included in the analysis. Design, manufacturing, and construction of the spent fuel storage rack are introduced. The spent fuel storage rack is for storage of spent fuel assemblies. The spent fuel storage rack should be designed, manufactured, and installed with consideration of predicted number of spent fuel assemblies, structural integrity, resistivity to corrosion and radiation, cleaning, and workability.

O-GlcNAcylation of RACK1 promotes hepatocellular carcinogenesis.

Science.gov (United States)

Duan, Fangfang; Wu, Hao; Jia, Dongwei; Wu, Weicheng; Ren, Shifang; Wang, Lan; Song, Shushu; Guo, Xinying; Liu, Fenglin; Ruan, Yuanyuan; Gu, Jianxin

2018-06-01

Aberrant oncogenic mRNA translation and protein O-linked β-N-acetylglucosaminylation (O-GlcNAcylation) are general features during tumorigenesis. Nevertheless, whether and how these two pathways are interlinked remain unknown. Our previous study indicated that ribosomal receptor for activated C-kinase 1 (RACK1) promoted chemoresistance and growth in hepatocellular carcinoma (HCC). The aim of this study is to examine the role of RACK1 O-GlcNAcylation in oncogene translation and HCC carcinogenesis. The site(s) of RACK1 for O-GlcNAcylation was mapped by mass spectrometry analysis. HCC cell lines were employed to examine the effects of RACK1 O-GlcNAcylation on the translation of oncogenic factors and behaviors of tumor cells in vitro. Transgenic knock-in mice were used to detect the role of RACK1 O-GlcNAcylation in modulating HCC tumorigenesis in vivo. The correlation of RACK1 O-GlcNAcylation with tumor progression and relapse were analyzed in clinical HCC samples. We found that ribosomal RACK1 was highly modified by O-GlcNAc at Ser122. O-GlcNAcylation of RACK1 enhanced its protein stability, ribosome binding and interaction with PKCβII (PRKCB), leading to increased eukaryotic translation initiation factor 4E phosphorylation and translation of potent oncogenes in HCC cells. Genetic ablation of RACK1 O-GlcNAcylation at Ser122 dramatically suppressed tumorigenesis, angiogenesis, and metastasis in vitro and in diethylnitrosamine (DEN)-induced HCC mouse model. Increased RACK1 O-GlcNAcylation was also observed in HCC patient samples and correlated with tumor development and recurrence after chemotherapy. These findings demonstrate that RACK1 acts as key mediator linking O-GlcNAc metabolism to cap-dependent translation during HCC tumorigenesis. Targeting RACK1 O-GlcNAcylation provides promising options for HCC treatment. O-GlcNAcylation of ribosomal receptor for activated C-kinase 1 at the amino acid serine122 promotes its stability, ribosome localization and interaction

30 CFR 57.7050 - Tool and drill steel racks.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Tool and drill steel racks. 57.7050 Section 57... Rotary Jet Piercing Drilling-Surface and Underground § 57.7050 Tool and drill steel racks. Receptacles or racks shall be provided for drill steel and tools stored or carried on drills. ...

Knot invariants derived from quandles and racks

OpenAIRE

Kamada, Seiichi

2002-01-01

The homology and cohomology of quandles and racks are used in knot theory: given a finite quandle and a cocycle, we can construct a knot invariant. This is a quick introductory survey to the invariants of knots derived from quandles and racks.

30 CFR 56.7050 - Tool and drill steel racks.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Tool and drill steel racks. 56.7050 Section 56.7050 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL... Jet Piercing Drilling § 56.7050 Tool and drill steel racks. Receptacles or racks shall be provided for...

AP Alternatives Modular Solar Racking

OpenAIRE

ECT Team, Purdue

2015-01-01

Solar panels have been used to generate and supply electricity in various applications such as residential and commercial buildings. Therefore, a need for a quicker approach to installation as well as the need to reduce workmanship to speed up the process is needed. Solar racks are developed through the use of automated equipment to “preassemble the racking hardware, pre-install the solar modules, and drive helical anchors into the ground rapidly”. So instead of installing one panel at a time...

Fabrication of the Spent Fuel Elements Rack on the ISFSF

International Nuclear Information System (INIS)

Slamet Wiranto; Sigit Purwanto; Safrul, H.

2004-01-01

The Interim Storage For Spent Fuel elements (ISFSF) was designed to be able to store the 33 spent fuel element racks with capacity of 1386 of normal spent fuel elements and 2 racks for 36 of defected ones. Until now, only 9 out of 33 racks of normal spent fuel elements and lout of 2 racks of defected fuel elements are available. Five of them have suffered from corrosion so that they are not fulfilled the requirements of the spent fuel elements storage anymore. Meanwhile, the spent fuel storage racks in the reactor are almost full. It means, the transfer of the spent fuel from reactor spent fuel storage to the ISFSF pool are compulsory needed. Therefore, it is necessary to provide the new ISFSF spent fuel storage rack with better material and fabrication method than the old one. In this design all materials consist of SS 316 L that are welded with the Argon TIG-welding. Right now there has been one new spent fuel storage rack fabricated with capacity of 42 normal spent fuel elements. (author)

Thermal Analysis Evaluation of Spent Fuel Storage Rack for Research Reactor

Energy Technology Data Exchange (ETDEWEB)

Lee, Sangjin; Oh, Jinho; Kwak, Jinsung; Lee, Jongmin [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2016-10-15

Spent fuel storage rack is to store spent fuel assemblies. The spent fuel storage rack is submerged in the designated pool for cooling. Due to the condition change of the pool water, the effect of thermal load on spent fuel storage rack must be analyzed and evaluated. In this paper, thermal stress analysis is performed and evaluated on a spent fuel storage rack. For thermal stress evaluation of the spent fuel storage rack, load combinations and allowable criteria in ASME Sec. III NB-3220 are applied. In cases of A-1 and B-1, the same temperature applied on the whole model, thermal stress doesn't occur because there is no constraint about the thermal expansion. The support frame is located on the pool bottom in free standing type and the racks are located in the support frame with enough space. Thermal expansion was considered and reflected in the design of spent fuel storage rack in advance. Thermal stress analysis is performed and evaluated on a spent fuel storage rack with consideration of pool water temperature variation. The thermal analysis including a linear heat transfer and the thermal stress analysis is performed for the racks and support frame and resulted stresses are within allowable criteria.

Decreased Blastocyst Production in Mice Exposed to Increased Rack Noise

Science.gov (United States)

Zamora, Bernadette M; Jiang, Meisheng; Wang, Ying; Chai, Minghua; Lawson, P Timothy; Lawson, Gregory W

2009-01-01

This study was conducted to investigate the possible effect of rack type on the blastocyst yield of mouse embryo donors. The first phase of the study consisted of housing some mice (group A) in a ventilated rack and others (group B) in a static rack in the same room for 3 d, followed by euthanasia for blastocyst collection and corticosterone assay. Parametric tests were used to compare groups. The number of blastocysts per donor was lower in group A (5.0 ± 1.4 blastocysts) than group B (13.1 ± 3.7 blastocysts). Mean noise was higher in the ventilated rack (80.4 dBC) than in the static rack (69.2 dBC). Serum corticosterone concentrations did not differ between groups. For the second phase of the study, a third group of mice (group C) was housed in a static rack without a ventilated rack in the same room. The noise level for group C was even lower (45.18 ± 2.91 dBC), and the blastocyst count per donor (16.4 ± 2.4) was higher than that of group B. The mean noise levels of empty ventilated and static racks differed significantly between groups for 10 different sound frequencies. Plotting mean blastocyst production against mean rack noise revealed a negative linear relationship with good strength of correlation. These results support the earlier observation that decreased blastocyst count occurs following housing of bred C57BL/6 donor mice in ventilated cages. PMID:19807968

High density aseismic spent fuel storage racks

International Nuclear Information System (INIS)

Louvat, J.P.

1985-05-01

After the reasons of the development of high density aseismic spent fuel racks by FRAMATOME and LEMER, a description is presented, as also the codes, standards and regulations used to design this FRAMATOME storage rack. Tests have been carried out concerning criticality, irradiation of Cadminox, corrosion of the cell, and the seismic behaviour

Habitat use by Red Knots (Calidris canutus rufa): Experiments with oyster racks and reefs on the beach and intertidal of Delaware Bay, New Jersey

Science.gov (United States)

Burger, Joanna; Niles, Lawrence J.

2017-07-01

Sea level rise and increasing human activities have decreased intertidal habitat in many places in the world. The expansion of aquaculture in intertidal areas may impact birds and other organisms using these habitats, leading to questions of sustainability of both aquaculture and functioning estuarine ecosystems. Understanding the effect of oyster culture on shorebird activity, particularly on Red Knots (Calidris canutus rufa), a species on the U.S. Threatened List, is important for adaptive management and the expansion of oyster culture. In May 2013 we experimentally compared Red Knot and shorebird use of a beach section with racks and a control, and in 2016 we compared the use of sections with artificial reefs, oyster racks, and control on Delaware Bay, New Jersey (USA). The data included only times when no workers or other people were present. Censuses, conducted every 30 min throughout the day (279 censuses in 2013, 231 censuses in 2016), included the number of Red Knots and other shorebirds in each treatment section. In 2013, the total number of shorebirds was significantly higher in the rack section than in the control section, except for Red Knots and Ruddy Turnstones (Arenaria interpres) that occurred in higher numbers in the control than in the rack section. In 2016 Red Knot numbers were also significantly lower in the rack section. In 2013, the mean number of Red Knots/census was 13 for racks vs 59 for the control (P racks and over 68 for other treatments (P racks while both foraging and roosting, suggesting that caution should be used before placing oyster racks in areas used for foraging by Red Knots.

ISS Material Science Research Rack HWIL Interface Simulation

Science.gov (United States)

Williams, Philip J.; Ballard, Gary H.; Crumbley, Robert T. (Technical Monitor)

2002-01-01

In this paper, the first Material Science Research Rack (MSRR-1) hardware-in-the-loop (HWIL) interface simulation is described. Dynamic Concepts developed this HWIL simulation system with funding and management provided by the Flight Software group (ED14) of NASA-MSFC's Avionics Department. The HWIL system has been used both as a flight software development environment and as a software qualification tool. To fulfill these roles, the HWIL simulator accurately models the system dynamics of many MSRR-1 subsystems and emulates most of the internal interface signals. The modeled subsystems include the Experiment Modules, the Thermal Environment Control System, the Vacuum Access System, the Solid State Power Controller Module, and the Active Rack Isolation Systems. The emulated signals reside on three separate MIL-STD-1553B digital communication buses, the ISS Medium Rate Data Link, and several analog controller and sensor signals. To enhance the range of testing, it was necessary to simulate several off-nominal conditions that may occur in the interfacing subsystems.

Innovative Ballasted Flat Roof Solar PV Racking System

Energy Technology Data Exchange (ETDEWEB)

Peek, Richard T. [Cascade Engineering, Grand Rapids, MI (United States)

2014-12-15

The objective of this project was to reduce the cost of racking for PV solar on flat commercial rooftops. Cost reductions would come from both labor savings and material savings related to the installation process. The rack would need to accommodate the majority of modules available on the market. Cascade Engineering has a long history of converting traditional metal type applications over to plastic. Injection molding of plastics have numerous advantages including selection of resin for the application, placing the material exactly where it is needed, designing in features that will speed up the installation process, and weight reduction of the array. A plastic rack would need to meet the requirements of UL2703, Mounting systems, mounting devices, clamping/retention devices, and ground lugs for use with flat-plate photovoltaic modules and panels. Comparing original data to the end of project racking design, racking material costs were reduced 50% and labor costs reduced 64%. The racking product accommodates all 60 and 72 cell panels on the market, meets UL2703 requirements, contributes only 1.3 pounds per square foot of weight to the array, requires little ballast to secure the array, automatically grounds the module when the module is secured, stacks/nests well for shipping/fewer lifts to the roof, provides integrated wire routing, allows water to drain on the roof, and accommodates various seismic roof connections. Project goals were achieved as noted in the original funding application.

Nonlinear dynamics of a rack-pinion-rack device powered by the Casimir force.

Science.gov (United States)

Miri, MirFaez; Nekouie, Vahid; Golestanian, Ramin

2010-01-01

Using the lateral Casimir force-a manifestation of the quantum fluctuations of the electromagnetic field between objects with corrugated surfaces-as the main force transduction mechanism, a nanomechanical device with rich dynamical behaviors is proposed. The device is made of two parallel racks that are moving in the same direction and a pinion in the middle that couples with both racks via the noncontact lateral Casimir force. The built-in frustration in the device causes it to be very sensitive and react dramatically to minute changes in the geometrical parameters and initial conditions of the system. The noncontact nature of the proposed device could help with the ubiquitous wear problem in nanoscale mechanical systems.

Safety Assessment of Multi Purpose Small Payload Rack(MSPR)

Science.gov (United States)

Mizutani, Yoshinobu; Takada, Satomi; Murata, Kosei; Ozawa, Daisaku; Kobayashi, Ryoji; Nakamura, Yasuhiro

2010-09-01

We are reporting summary of preliminary safety assessment for Multi Purpose Small Payload Rack(MSPR), which is one of the micro gravity experiment facilities that are being developed for the 2nd phase JEM utilization(JEM: Japanese Experiment Module) that will be launched on H-II Transfer Vehicle(HTV) 2nd flight in 2011. MSPR is used for multi-purpose micro-g experiment providing experimental spaces and work stations. MSPR has three experimental spaces; first, there is a space called Work Volume(WV) with capacity volume of approximately 350 litters, in which multiple resources including electricity, communication, and moving image functions can be used. Within this space, installation of devices can be done by simple, prompt attachment by Velcro and pins with high degree of flexibility. Second, there is Small Experiment Area(SEA), with capacity volume of approximately 70 litters, in which electricity, communication, and moving image functions can also be used in the same way as WV. These spaces protect experiment devices and specimens from contingent loads by the crewmembers. Third, there is Work Bench with area of 0.5 square meters, on which can be used for maintenance, inspection and data operations of installed devices, etc. This bench can be stored in the rack during contingency. Chamber for Combustion Experiment(CCE) that is planned to be installed in WV is a pressure-resistant experimental container that can be used to seal hazardous materials from combustion experiments. This CCE has double sealing design in chamber itself, which resist gas leakage under normal the temperature and pressure. Electricity, communication, moving image function can be used in the same way as WV. JAXA Phase 2 Safety Review Panel(SRP) has been held in April, 2010. For safety analysis of MSPR, hazards were identified based on Fault Tree Analysis methodology and then these hazards were classified into either eight ISS standard-type hazards or eight unique-type hazards that requires

Design of a new wet storage rack for spent fuels from IEA-R1 reactor

International Nuclear Information System (INIS)

Rodrigues, Antonio C.I.; Madi Filho, Tufic; Siqueira, Paulo T.D.; Ricci Filho, Walter

2015-01-01

The IEA-R1 research reactor operates in a regimen of 64h weekly, at the power of 4.5 MW. In these conditions, the racks of the spent fuel elements have less than half of its initial capacity. Thus, maintaining these operating conditions, the storage will have capacity for about six years. Since the estimated useful life of the IEA-R1 is about another 20 years, it will be necessary to increase the storage capacity of spent fuel. Dr. Henrik Grahn, expert of the International Atomic Energy Agency on wet storage, visiting the IEA-R1 Reactor (September/2012) made some recommendations: among them, the design and installation of racks made with borated stainless steel and internally coated with an aluminum film, so that corrosion of the fuel elements would not occur. After an extensive literature review of material options given for this type of application we got to Boral® manufactured by 3M due to numerous advantages. This paper presents studies on the analysis of criticality using the computer code MCNP 5, demonstrating the possibility of doubling the storage capacity of current racks to attend the demand of the IEA-R1 reactor while attending the safety requirements the International Atomic Energy Agency. (author)

Design of a new wet storage rack for spent fuels from IEA-R1 reactor

Energy Technology Data Exchange (ETDEWEB)

Rodrigues, Antonio C.I.; Madi Filho, Tufic; Siqueira, Paulo T.D.; Ricci Filho, Walter, E-mail: acirodri@ipen.br, E-mail: tmfilho@ipen.br, E-mail: ptsiquei@ipen.br, E-mail: wricci@ipen.br [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

2015-07-01

The IEA-R1 research reactor operates in a regimen of 64h weekly, at the power of 4.5 MW. In these conditions, the racks of the spent fuel elements have less than half of its initial capacity. Thus, maintaining these operating conditions, the storage will have capacity for about six years. Since the estimated useful life of the IEA-R1 is about another 20 years, it will be necessary to increase the storage capacity of spent fuel. Dr. Henrik Grahn, expert of the International Atomic Energy Agency on wet storage, visiting the IEA-R1 Reactor (September/2012) made some recommendations: among them, the design and installation of racks made with borated stainless steel and internally coated with an aluminum film, so that corrosion of the fuel elements would not occur. After an extensive literature review of material options given for this type of application we got to Boral® manufactured by 3M due to numerous advantages. This paper presents studies on the analysis of criticality using the computer code MCNP 5, demonstrating the possibility of doubling the storage capacity of current racks to attend the demand of the IEA-R1 reactor while attending the safety requirements the International Atomic Energy Agency. (author)

Furniture Rack Corrosion Coupon Surveillance - 2012 Update

International Nuclear Information System (INIS)

Mickalonis, J. I.; Murphy, T. R.; Berry, C. J.

2012-01-01

Under the L Basin corrosion surveillance program furniture rack coupons immersed for 14 years (FY2009 coupons) and 16 years (FY2011 coupons) were analyzed and the results trended with coupons exposed for shorter times. In addition, a section harvested from an actual furniture rack that was immersed for 14 years was analyzed for pitting in the weld and heat-affected-zone (HAZ) regions. The L Basin operations maintained very good water quality over the entire immersion period for these samples. These results for FY2009 and FY2011 coupons showed that the average pit depths for the 6061 and 6063 base metal are 1 and 2 mils, respectively, while those for the weld and HAZ are 3 and 4 mils, respectively. The results for the weld and HAZ regions are similar to coupons removed during the period of FY2003 to FY2007. These similarities indicate that the pit development occurred quickly followed by slow kinetics of increase in pit depth. For the actual furniture rack sample average pits of 5 and 2 mils were measured for the HAZ and weld, respectively. These results demonstrate that pitting corrosion of the aluminum furniture racks used to support the spent fuel occurs in waters of good quality. The corrosion kinetics or pit depth growth rate is much less that 1 mil/year, and would not impact long-term use of this material system for fuel storage racks in L Basin if good water quality is maintained

Experimental and Numerical Study of Bottom Rack Occlusion by Flow with Gravel-Sized Sediment. Application to Ephemeral Streams in Semi-Arid Regions

Directory of Open Access Journals (Sweden)

Luis G. Castillo

2016-04-01

Full Text Available Rainfall runoff collection in ephemeral streams is an objective in semi-arid zones. Rack intake systems are proposed to collect these flash floods with intensive sediment transport. The design parameters address the problem of clogging the spacing between bars. Experiments for two different void ratio racks are shown. Flows, longitudinal slopes in the rack, and water with three gravel-sized sediments were tested. Results such as effective void ratio due to the gravel deposition over the rack, the evolution of the flow rejected during each test, and the quantification of materials collected and deposited, are presented. The optimal longitudinal rack slope seems to be close to 30%. The effective void ratio is related to several hydraulic parameters calculated at the beginning of the rack. Some adjustments were proposed to predict the effective void ratio.

Laboratory glassware rack for seismic safety

Science.gov (United States)

Cohen, M. M. (Inventor)

1985-01-01

A rack for laboratory bottles and jars for chemicals and medicines has been designed to provide the maximum strength and security to the glassware in the event of a significant earthquake. The rack preferably is rectangular and may be made of a variety of chemically resistant materials including polypropylene, polycarbonate, and stainless steel. It comprises a first plurality of parallel vertical walls, and a second plurality of parallel vertical walls, perpendicular to the first. These intersecting vertical walls comprise a self-supporting structure without a bottom which sits on four legs. The top surface of the rack is formed by the top edges of all the vertical walls, which are not parallel but are skewed in three dimensions. These top edges form a grid matrix having a number of intersections of the vertical walls which define a number of rectangular compartments having varying widths and lengths and varying heights.

Benchmarking criticality analysis of TRIGA fuel storage racks.

Science.gov (United States)

Robinson, Matthew Loren; DeBey, Timothy M; Higginbotham, Jack F

2017-01-01

A criticality analysis was benchmarked to sub-criticality measurements of the hexagonal fuel storage racks at the United States Geological Survey TRIGA MARK I reactor in Denver. These racks, which hold up to 19 fuel elements each, are arranged at 0.61m (2 feet) spacings around the outer edge of the reactor. A 3-dimensional model was created of the racks using MCNP5, and the model was verified experimentally by comparison to measured subcritical multiplication data collected in an approach to critical loading of two of the racks. The validated model was then used to show that in the extreme condition where the entire circumference of the pool was lined with racks loaded with used fuel the storage array is subcritical with a k value of about 0.71; well below the regulatory limit of 0.8. A model was also constructed of the rectangular 2×10 fuel storage array used in many other TRIGA reactors to validate the technique against the original TRIGA licensing sub-critical analysis performed in 1966. The fuel used in this study was standard 20% enriched (LEU) aluminum or stainless steel clad TRIGA fuel. Copyright © 2016. Published by Elsevier Ltd.

The optimization of spent fuel assembly storage racks in nuclear power plants

International Nuclear Information System (INIS)

Wang Yan

2005-01-01

This paper gives an evaluation of the spent fuel assembly storage racks in the nuclear power plants at home and abroad, focusing on the characteristics of the high density storage racks and the aseismatic design. It mainly discusses structures and characteristics of the spent fuel assembly storage racks in the Qinshan nuclear power phase II project. Concluding the crucial technical difficulties of the high density spent fuel assembly storage racks: the neutron-absorbing materials, the structural aseismatic design technology and the security analysis technology, this paper firstly generalizes several important neutron-absorbing materials, then introduces the evolution of the aseismatic design of the spent fuel assembly storage racks . In the last part, it describes the advanced aseismatic analysis technology in the Qinshan nuclear power phase II project. Through calculation and analysis for such storage racks, the author concludes several main factors that could have an influence on the aseismatic performance and thus gives the key points and methods for designing the optimal racks and provides some references for the design of advanced spent fuel assembly storage racks in the future. (authors)

Recalculation with SEACAB of the activation by spent fuel neutrons and residual dose originated in the racks replaced at Cofrentes NPP

Directory of Open Access Journals (Sweden)

Ortego Pedro

2017-01-01

Full Text Available In order to increase the storage capacity of the East Spent Fuel Pool at the Cofrentes NPP, located in Valencia province, Spain, the existing storage stainless steel racks were replaced by a new design of compact borated stainless steel racks allowing a 65% increase in fuel storing capacity. Calculation of the activation of the used racks was successfully performed with the use of MCNP4B code. Additionally the dose rate at contact with a row of racks in standing position and behind a wall of shielding material has been calculated using MCNP4B code as well. These results allowed a preliminary definition of the burnker required for the storage of racks. Recently the activity in the racks has been recalculated with SEACAB system which combines the mesh tally of MCNP codes with the activation code ACAB, applying the rigorous two-step method (R2S developed at home, benchmarked with FNG irradiation experiments and usually applied in fusion calculations for ITER project.

Recalculation with SEACAB of the activation by spent fuel neutrons and residual dose originated in the racks replaced at Cofrentes NPP

Science.gov (United States)

Ortego, Pedro; Rodriguez, Alain; Töre, Candan; Compadre, José Luis de Diego; Quesada, Baltasar Rodriguez; Moreno, Raul Orive

2017-09-01

In order to increase the storage capacity of the East Spent Fuel Pool at the Cofrentes NPP, located in Valencia province, Spain, the existing storage stainless steel racks were replaced by a new design of compact borated stainless steel racks allowing a 65% increase in fuel storing capacity. Calculation of the activation of the used racks was successfully performed with the use of MCNP4B code. Additionally the dose rate at contact with a row of racks in standing position and behind a wall of shielding material has been calculated using MCNP4B code as well. These results allowed a preliminary definition of the burnker required for the storage of racks. Recently the activity in the racks has been recalculated with SEACAB system which combines the mesh tally of MCNP codes with the activation code ACAB, applying the rigorous two-step method (R2S) developed at home, benchmarked with FNG irradiation experiments and usually applied in fusion calculations for ITER project.

Double beta decay: experiments

International Nuclear Information System (INIS)

Fiorini, Ettore

2006-01-01

The results obtained so far and those of the running experiments on neutrinoless double beta decay are reviewed. The plans for second generation experiments, the techniques to be adopted and the expected sensitivities are compared and discussed

Rack Distribution Effects on MPLM Center of Mass

Science.gov (United States)

Tester, John T.

2005-01-01

This research was in support of exploring the need for more flexible "center of gravity (CG) specifications than those currently established by NASA for the Multi-Purpose Logistics Module (MPLM). The MPLM is the cargo carrier for International Space Station (ISS) missions. The MPLM provides locations for 16 standard racks, as shown in Figure 1; not all positions need to be filled in any given flight. The MPLM coordinate system (X(sub M), Y(sub M), Z(sub M)) is illustrated as well. For this project, the primary missions of interest were those which supply the ISS and remove excess materials on the return flights. These flights use a predominate number of "Resupply Stowage Racks" (RSR) and "Resupply Stowage Platforms" (RSP). In these two types of racks, various smaller items are stowed. Hence, these racks will exhibit a considerable range of mass values as well as a range as to where their individual CG are located.

Nonlinear dynamic response of whole pool multiple spent fuel racks subject to three-dimensional excitations

International Nuclear Information System (INIS)

Zhao, Y.; Wilson, P.R.; Stevenson, J.D.

1995-01-01

The seismic evaluation of submerged free standing spent fuel storage racks is more complicated than most other nuclear structural systems. When subjected to three dimensional (3-D) floor seismic excitations the dynamic responses of racks in a pool are hydro dynamically coupled with each other, with the fuel assemblies water in gaps. The motion behavior of the racks is significantly different from that observed using a 3D single rack mode. Few seismic analyses using 3-D whole pool multiple rack models are available in the literature. I this paper an analysis was performed for twelve racks using potential theory for the fluid-structure interaction, and using a 3-D whole pool multi-rack finite element model developed herein. The analysis includes the potential nonlinear dynamic behavior of the impact of fuel-rack, rack-rack and rack-pool wall, the tilting or uplift and the frictional sliding of rack supports, and the impact of the rack supports to the pool floor. (author). 12 refs., 7 figs., 1 tab

A Study on Rack Thickness Effect for Spent Fuel Pool Storage

International Nuclear Information System (INIS)

Kim, Mi Jin; Lee, Hee-Jae; Sohn, Dong-Seong

2015-01-01

For the effective storage of used fuel, the development of high performance neutron absorbing materials is needed. One of the major concern for the used fuel storage is the assurance to keep subcriticality of the storage rack and the high performance neutron absorbing material is the vital part to assure this requirement. According to NRC guide line, the k-effective of the spent fuel storage racks must not exceed 0.95. To ensure its safety, subcriticality analysis is required. Subcriticality analysis of the used storage in spent fuel pool have been performed by different authors. Criticality calculations for light water reactor spent fuel storage rack were carried out by Jae et al. They used AMPX-KENO IV code and considered the effect of rack pitch and rack thickness for consolidated fuel. The criticality analysis has performed at Gd 0.2 and 1 wt% according to thickness change. As thickness increases, the volume of the spent fuel pool rack increases. Therefore, absorbing material also increases according to thickness

A Study on Rack Thickness Effect for Spent Fuel Pool Storage

Energy Technology Data Exchange (ETDEWEB)

Kim, Mi Jin; Lee, Hee-Jae; Sohn, Dong-Seong [Ulsan National Institute of Science and Technology, Ulsan (Korea, Republic of)

2015-05-15

For the effective storage of used fuel, the development of high performance neutron absorbing materials is needed. One of the major concern for the used fuel storage is the assurance to keep subcriticality of the storage rack and the high performance neutron absorbing material is the vital part to assure this requirement. According to NRC guide line, the k-effective of the spent fuel storage racks must not exceed 0.95. To ensure its safety, subcriticality analysis is required. Subcriticality analysis of the used storage in spent fuel pool have been performed by different authors. Criticality calculations for light water reactor spent fuel storage rack were carried out by Jae et al. They used AMPX-KENO IV code and considered the effect of rack pitch and rack thickness for consolidated fuel. The criticality analysis has performed at Gd 0.2 and 1 wt% according to thickness change. As thickness increases, the volume of the spent fuel pool rack increases. Therefore, absorbing material also increases according to thickness.

MSRR Rack Materials Science Research Rack

Science.gov (United States)

Reagan, Shawn

2017-01-01

The Materials Science Research Rack (MSRR) is a research facility developed under a cooperative research agreement between NASA and the European Space Agency (ESA) for materials science investigations on the International Space Station (ISS). The MSRR is managed at the Marshall Space Flight Center (MSFC) in Huntsville, AL. The MSRR facility subsystems were manufactured by Teledyne Brown Engineering (TBE) and integrated with the ESA/EADS-Astrium developed Materials Science Laboratory (MSL) at the MSFC Space Station Integration and Test Facility (SSITF) as part of the Systems Development Operations Support (SDOS) contract. MSRR was launched on STS-128 in August 2009, and is currently installed in the U. S. Destiny Laboratory Module on the ISS. Materials science is an integral part of developing new, safer, stronger, more durable materials for use throughout everyday life. The goal of studying materials processing in space is to develop a better understanding of the chemical and physical mechanisms involved, and how they differ in the microgravity environment of space. To that end, the MSRR accommodates advanced investigations in the microgravity environment of the ISS for basic materials science research in areas such as solidification of metals and alloys. MSRR allows for the study of a variety of materials including metals, ceramics, semiconductor crystals, and glasses. Materials science research benefits from the microgravity environment of space, where the researcher can better isolate chemical and thermal properties of materials from the effects of gravity. With this knowledge, reliable predictions can be made about the conditions required on Earth to achieve improved materials. MSRR is a highly automated facility with a modular design capable of supporting multiple types of investigations. Currently the NASA-provided Rack Support Subsystem provides services (power, thermal control, vacuum access, and command and data handling) to the ESA developed Materials

Behavior of high-density spent-fuel storage racks

International Nuclear Information System (INIS)

Bailey, W.J.

1986-08-01

Included in this report is a summary of information on neutron-absorbing materials such as B 4 C in an aluminum matrix or organic binder material, stainless steel-boron and aluminum-boron alloys, and stainless steetl-clad cadmium that are used in high-density spent fuel storage racks. A list of the types of neutron-absorbing materials being used in spent fuel storage racks at domestic commercial plants is provided. Recent cases at several domestic plants where swelling of rack side plates (where the B 4 C in an aluminum matrix and B 4 C in an organic binder material were located) occurred are reviewed

Effects of poison panel shrinkage and gaps on fuel storage rack reactivity

International Nuclear Information System (INIS)

Boyd, W.A.; Mueller, D.E.

1988-01-01

Fixed poison panels are used in spent fuel rack designs to increase enrichment limits and reduce cell spacing; therefore, assurances that the maximum rack reactivity will meet the design limit (0.95) throughout the lifetime of the racks depend on the continued effectiveness of the poison with time. Industry data have shown that poison panels will shrink under irradiated conditions. From recent data, however, poison panels have been found to have gaps spanning their width after relatively short operating periods. This paper presents results of studies showing the fuel rack reactivity changes associated with poison panel shrinkage and formation of gaps. The discovery of gaps in the fuel rack poison panels at an operating plant raises concerns regarding the effectiveness of the poison over the lifetime of the fuel racks. Studies performed to evaluate the effect of the poison panel shrinkage on reactivity show that reactivity changes from zero to several percent are possible depending on the initial panel size. Results of recent studies show that some gaps can be accommodated in the fuel rack poison panels at the fuel midplane without causing the fuel rack K eff limit to be exceeded. With worst-case assumptions concerning gap size and the number of panels affected, other actions will likely be required to show that the rack K eff design limit will not be exceeded

Evaluation of food storage racks available on the Polish market in the hygienic context

Science.gov (United States)

Grzesińska, Wiesława; Tomaszewska, Marzena; Bilska, Beata; Trafiałek, Joanna; Dziadek, Michał

Providing safe food products to the consumer depends on the material and technology used and adherence to hygienic practices, throughout the production process. The degree of microbial contamination of a surface is an important indicator of equipment cleanliness and effectiveness of cleaning and disinfection. Used material, construction solutions and quality of the applied devices also have an effect on hygienic status. The objective of the present study was to evaluate the influence of the design and construction material of selected food storage racks, available on the Polish market, on their hygienic status. The study was based on determination of the capability of microbial growth on the surface of the racks and the effectiveness of their cleaning. Microbiological cleanliness on the surface of the racks was monitored by the contact plates which are able to estimate the total number of icroorganisms. Examination of effectiveness of cleaning was conducted by the use of ATP bioluminescence method. This experiment has proven a significant influence of adopted construction solutions on the hygienic status of the examined racks. Presence of antibacterial layer and a choice of the appropriate construction material characterized by a low surface roughness impedes the microbial growth and increases the effectiveness of cleaning. Design solutions have significant impact on the hygienic status of shelves. Selection of a suitable material for the construction of racks can greatly reduce the possibility of the development of microorganism, despite the low efficiency of the cleaning. The application of antimicrobial coatings inhibits microbial growth.

Fuel storage rack

International Nuclear Information System (INIS)

Mollon, L.

1977-01-01

Disclosed is a storage rack for spent nuclear fuel elements comprising a multiplicity of elongated hollow containers of uniform cross-section, preferably square,some of said containers having laterally extending continuous flanges extending between adjacent containers and defining continuous elongated chambers therebetween for the reception of neutron absorbing panels. 18 claims, 7 figures

Nuclear reactor spent fuel storage rack

International Nuclear Information System (INIS)

Machado, O.J.; Flynn, W.M.; Flanders, H.E. Jr.; Booker, L.W.

1989-01-01

A fuel rack is described for use in storing nuclear fuel assemblies in a nuclear fuel storage pool having a floor on which an upwardly projecting stud is mounted; the fuel rack comprising: a base structure at the lower end of the fuel rack including base-plate means having flow openings therein, the base-plate means supporting a first network of interlaced beams which form a multiplicity of polygonal openings; a second network of interlaced beams forming polygonal openings positioned in spaced vertical alignment with corresponding polygonal openings in the first network of beams; a plurality of cells, each cell having sides bounded by inner and outer surfaces and being of a size and configuration designed to hold therein a fuel assembly, each cell positioned in a corresponding pair of the aligned polygonal openings, each cell being open at both ends with a guiding funnel at the upper end, and the cells being positioned over the flow openings in the base-plate to permit flow of coolant through the cells; spaced, outwardly directed, projections on the outer surfaces of the sides of the cells near the tops and bottoms of the sides thereof, each cell being sized to be received within a corresponding of the pair of aligned polygonal openings in which the cells are respectively positioned; and means fixedly securing the projections to the beams in the first and second networks of beams thereby to provide a substantially rigid fuel rack of modular design

Chin Shan analyses show advantages of whole pool multi-rack approach

International Nuclear Information System (INIS)

Singh, K.P.; Soler, A.I.

1991-01-01

Nuclear fuel storage racks are essentially thin-walled, cellular structures of prismatic cross-section. Although the details of design vary from one supplier to another, certain key physical attributes are common to all designs. For example, all racks feature square cells of sufficient opening size and height to enable insertion and withdrawal of the fuel assembly. The array of cells is positioned in a vertical orientation and is supported off the pool slab surface by four or more support legs. The spent fuel pool is filled with the individual fuel racks. The plenum created by the support legs is essential for proper cooling of the fuel assemblies stored in the rack, which relies on natural convective cooling to extract the heat emitted by the spent fuel. However, it has the insalutary effect of making it kinematically less stable. Regulatory authorities require careful and comprehensive analysis of the response of the racks under the seismic motions postulated for the pool slab. Results from whole pool multi-rack (WPMR) analyses at the Chin Shan and Oyster Creek nuclear plants point up the potential inadequacies of single rack 3D analyses, and show just how important it is to carry out WPMR simulations, despite their abstruseness and high cost. (author)

Nonlinear analyses of spent-fuel racks for consolidated fuel loading

International Nuclear Information System (INIS)

Kabir, A.F.; Godha, P.C.; Malik, L.E.; Bolourchi, S.

1987-01-01

Storage racks for spent-fuel assemblies in nuclear power plants are designed to withstand various combinations of loads generated by gravity, seismic, thermal, and accidental fuel drops. Due to the need for storing increased amounts of spent fuel in the existing fuel pools, many nuclear power utilities are evaluating existing fuel racks to safely carry the additional loads. The current study presents the seismic analyses of existing fuel racks of Northeast Utility Company's Millstone Unit Number 1 (BWR Mark I) nuclear plant to accommodate a 2:1 fuel consolidation. This objective requires rigorous nonlinear analyses to establish the full available capacities of the racks and thereby avoid expensive modifications or minimize any needed upgrades

'Swab racks are an old fashioned idea'.

Science.gov (United States)

Mumford, M

1991-12-01

Mary Mumford, theatre sister at the Princes of Wales Hospital, Bridgend, was asked to speak in a short debate at an NATN branch meeting, supporting the motion that 'swab racks are an old fashioned idea'. Although she did not like swab racks she had not attempted thus far to do anything about them. In the event, she actually lost the debate--not in principle but because she could offer no effective alternative method of checking swabs. Having been given the incentive, a trial is now being conducted in her hospital similar to that described by Paul Wicker. This is the case presented by Mary Mumford supporting the following motion ... 'that swab racks are an old fashioned idea, which cause more potential problems due to exposure of blood than is proven to be safe in today's theatre environment'.

Double Chooz experiment

International Nuclear Information System (INIS)

Palomares, C.

2009-01-01

Double Chooz will use two identical detectors at different distances from the Chooz nuclear power station to search for a non-vanishing value of θ 13 , and, hopefully, to open the way to experiments aspiring to discover CP violation in the leptonic sector. The far detector is expected to be operative by the end of 2009. Installation of the near detector will occur in 2010. Double Chooz has the capacity to exclude sin 2 (2θ 13 ) 31 2 = 2.5 x 10 -3 eV 2 with three years of data running both near and far detectors. (author)

Criticality safety analysis of the NPP Krsko storage racks

International Nuclear Information System (INIS)

Kromar, M.; Kurincic, B.

2002-01-01

NPP Krsko is going to increase the capacity of the spent fuel storage pool by replacement of the existing racks with high-density racks. This will be the second reracking campaign since 1983 when storage was increased from 180 to 828 storage locations. The pool capacity will increase from 828 to 1694 with partial reracking by the spring 2003. The installed capacity will be sufficient for the current design plant lifetime. Complete reracking of the spent fuel pool will additionally increase capacity to 2321 storage locations. The design, rack manufacturing and installation has been awarded to the Framatome ANP GmbH. Burnup credit methodology, which was approved by the Slovenian Nuclear Safety Administration in previous licensing of existing racks, will be again implemented in the licensing process with the recent methodology improvements. Specific steps of the criticality safety analysis and representative results are presented in the paper.(author)

Accident Analysis of High Density Storage Rack for Fresh Fuel Assemblies

International Nuclear Information System (INIS)

Jang, K. J.; Lee, M. J.; Jin, H. U.; Park, J. H.; Shin, S. Y.

2009-01-01

Recently KONES and KNF have developed the so called suspension-type High Density Storage Rack (HDSR) for fresh fuel assemblies. The USNRC OT position paper specifies that the design of the rack must ensure the functional integrity of the fuel racks under all credible fuel assembly drop events. In this context the functional integrity means the criticality safety. That is to say, the drop events must not bring any danger to the criticality safety of HDSR. This paper shows the results of the analysis carried out to demonstrate the regulatory compliance of the proposed racks under postulated accidental drop events

C-188 Co-60 sources installation and source rack loading optimization processes in a gamma irradiation facility

Energy Technology Data Exchange (ETDEWEB)

Santos, Paulo de S.; Vasquez, Pablo A.S., E-mail: psantos@ipen.br, E-mail: pavsalva@ipen.br [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

2017-11-01

Since 2004, the Multipurpose Gamma Facility at the Nuclear and Energy Research Institute has been providing services on radiation processing for disinfection and sterilization of health care and disposable medical products as well to support research studies on modification of physical, chemical and biological properties of several materials. Recently, there was an increment in irradiation of the Cultural Heritages. This facility uses C-188 double-encapsulated radioactive Cobalt-60 sources known as pencils from manufactures outside of country. The activity of the cobalt sources decays into a stable nickel isotope with a half-life around 5.27 years, which means a loss of 12.3% annually. Then, additional pencils of Cobalt-60 are added periodically to the source rack to maintain the required capacity or installed activity of the facility. The manufacturer makes shipping of the radioactive sources inside a high density container type B(U) , by sea. This one involves many administrative, transport and radiation safety procedures. Once in the facility, the container is opened inside a deep pool water to remove the pencils. The required source geometry of the facility is obtained by loading these source pencils into predetermined diagram or positions in source modules and distributing these modules over the source rack of the facility. The dose variation can be reduced placing the higher activity source pencils near the periphery of the source rack. In this work are presented the procedures for perform the boiling leaching tests applied to the container, the Cobalt-60 sources installation, the loading processes and the source rack loading optimization. (author)

Evolution of design concepts for remotely maintainable equipment racks

International Nuclear Information System (INIS)

Peishel, F.L.; Mouring, R.W.; Schrock, S.L.

1986-01-01

Equipment racks have been used to support process equipment in radioactive facilities for many years. Improvements in the design of these racks have evolved relatively slowly primarily as a result of limitations in the capabilities of maintenance equipment; that is, tasks could only be approached from above using bridge cranes with viewing primarily through periscopes. In recent years, however, technological advances have been made by the Consolidated Fuel Reprocessing Program (CFRP) at Oak Ridge National Laboratory (ORNL) in bridge-mounted servomanipulators with onboard auxiliary hoists and television viewing systems. These advances permit full cell coverage by the manipulator arms which, in turn, allow maintenance tasks to be approached horizontally as well as from above. Maintainable equipment items can be stacked vertically on a rack because total overhead access is less important and maintenance tasks that would not have been attempted in the past can now be performed. These advances permit greater flexibility in the design and cell layout of the racks and lead to concepts that could significantly increase the availability of a facility. The evolution of rack design and a description of the alternative concepts based on present maintenance systems capabilities are presented in this paper. 13 refs., 11 figs

Improved method to demonstrate the structural integrity of high density fuel storage racks

International Nuclear Information System (INIS)

Hinderks, M.; Ungoreit, H.; Kremer, G.

2001-01-01

Reracking of existing fuel pools to the maximum extent is desirable from an economical point of view. This goal can be achieved by minimizing the gaps between the spent fuel storage racks. Since the rack design is aimed at enabling consolidated fuel rod storage, additional requirements arise with respect to the design and the structural analysis. The loads resulting from seismic events are decisive for the structural analysis and require a specially detailed and in-depth analysis for high seismic loads. The verification of structural integrity and functionality is performed in two phases. In the first phase the motional behavior of single racks, rows of racks and, where required, of all racks in the pool is simulated by excitation with displacement time histories under consideration of the fluid-structure interaction (FSI). The displacements from these simulations are evaluated, while the loads are utilized as input data for the structural analysis of the racks and the pool floor. The structural analyses for the racks comprise substantially stress analyses for base material and welds as well as stability analyses for the support channels and the rack outside walls. The analyses are performed in accordance with the specified codes and standards

Manufacturing and Construction of Fresh Fuel Storage Rack for a Research Reactor

Energy Technology Data Exchange (ETDEWEB)

Oh, Jinho; Lee, Sangjin; Lee, Jongmin; Ryu, Jeong-Soo [KAERI, Daejeon (Korea, Republic of)

2016-05-15

The objective of this study is to provide the manufacturing and construction information regarding the Fresh Fuel Storage Rack (FFSR). The main function of a FFSR is to store and protect the 2 core new fuel assemblies for the operation of the research reactor. The fresh fuel assemblies are stored in a rack made of stainless steel and the storage rack is installed in the fresh fuel storage room. The fresh fuel facility provides fresh fuel assemblies with dry storage space. General design requirements of the fresh fuel storage facilities are given in the ANSI-57.3. Design, manufacturing, and construction of the fresh fuel storage rack are introduced. The analysis is performed to confirm the structural intensity of the fresh fuel storage rack under the seismic loads. The fresh fuel storage rack designed for storage of fresh fuel assemblies should be manufactured and installed with consideration of predicted number of fresh fuel assemblies, structural integrity, resistivity to corrosion and radiation, cleaning, and workability.

Manufacturing and Construction of Fresh Fuel Storage Rack for a Research Reactor

International Nuclear Information System (INIS)

Oh, Jinho; Lee, Sangjin; Lee, Jongmin; Ryu, Jeong-Soo

2016-01-01

The objective of this study is to provide the manufacturing and construction information regarding the Fresh Fuel Storage Rack (FFSR). The main function of a FFSR is to store and protect the 2 core new fuel assemblies for the operation of the research reactor. The fresh fuel assemblies are stored in a rack made of stainless steel and the storage rack is installed in the fresh fuel storage room. The fresh fuel facility provides fresh fuel assemblies with dry storage space. General design requirements of the fresh fuel storage facilities are given in the ANSI-57.3. Design, manufacturing, and construction of the fresh fuel storage rack are introduced. The analysis is performed to confirm the structural intensity of the fresh fuel storage rack under the seismic loads. The fresh fuel storage rack designed for storage of fresh fuel assemblies should be manufactured and installed with consideration of predicted number of fresh fuel assemblies, structural integrity, resistivity to corrosion and radiation, cleaning, and workability

Three-dimensional seismic analysis for spent fuel storage rack

International Nuclear Information System (INIS)

Lee, Gyu Mahn; Kim, Kang Soo; Park, Keun Bae; Park, Jong Kyun

1998-01-01

Time history analysis is usually performed to characterize the nonlinear seismic behavior of a spent fuel storage rack (SFSR). In the past, the seismic analyses of the SFSR were performed with two-dimensional planar models, which could not account for torsional response and simultaneous multi-directional seismic input. In this study, three-dimensional seismic analysis methodology is developed for the single SFSR using the ANSY code. The 3-D model can be used to determine the nonlinear behavior of the rack, i.e., sliding, uplifting, and impact evaluation between the fuel assembly and rack, and rack and the pool wall. This paper also reviews the 3-D modeling of the SFSR and the adequacy of the ANSYS for the seismic analysis. As a result of the adequacy study, the method of ANSYS transient analysis with acceleration time history is suitable for the seismic analysis of highly nonlinear structure such as an SFSR but it isn't appropriate to use displacement time history of seismic input. (author)

Review of modern double beta decay experiments

Science.gov (United States)

Barabash, A. S.

2015-10-01

The review of modern experiments on search and studying of double beta decay processes is done. Results of the most sensitive current experiments are discussed. The main attention is paid to EXO-200, KamLAND-Zen, GERDA-I and CUORE-0 experiments. Modern values of T1/2(2ν) and best present limits on neutrinoless double beta decay and double beta decay with Majoron emission are presented. Conservative limits on effective mass of a Majorana neutrino ( at the level of ˜ 0.01-0.1 eV are discussed.

Flow field mapping in data rack model

Directory of Open Access Journals (Sweden)

Matěcha J.

2013-04-01

Full Text Available The main objective of this study was to map the flow field inside the data rack model, fitted with three 1U server models. The server model is based on the common four-processor 1U server. The main dimensions of the data rack model geometry are taken fully from the real geometry. Only the model was simplified with respect to the greatest possibility in the experimental measurements. The flow field mapping was carried out both experimentally and numerically. PIV (Particle Image Velocimetry method was used for the experimental flow field mapping, when the flow field has been mapped for defined regions within the 2D/3D data rack model. Ansys CFX and OpenFOAM software were used for the numerical solution. Boundary conditions for numerical model were based on data obtained from experimental measurement of velocity profile at the output of the server mockup. This velocity profile was used as the input boundary condition in the calculation. In order to achieve greater consistency of the numerical model with experimental data, the numerical model was modified with regard to the results of experimental measurements. Results from the experimental and numerical measurements were compared and the areas of disparateness were identified. In further steps the obtained proven numerical model will be utilized for the real geometry of data racks and data.

40 CFR 63.2475 - What requirements must I meet for transfer racks?

Science.gov (United States)

2010-07-01

... transfer racks? 63.2475 Section 63.2475 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... must I meet for transfer racks? (a) You must comply with each emission limit and work practice standard in table 5 to this subpart that applies to your transfer racks, and you must meet each applicable...

Refurbishment of the rotating rack of the OSU TRIGA MKII reactor

International Nuclear Information System (INIS)

Higginbotham, J.F.; Dodd, B.; Pratt, D.S.; Anderson, T.V.

1992-01-01

Many TRIGA reactors have experienced operational difficulties with the rotating racks used for sample irradiation. Generally the rack gradually becomes more difficult to rotate until it finally seizes. The recommended action at that point is replacement of the entire facility at a significant cost. The purpose of this paper is to describe the symptoms leading to rack failure and to present the results of a refurbishment procedure that does not involve the use of solvents which create mixed chemical and radioactive hazardous waste. The primary reason for rack failure is the buildup of sludge produced through irradiation of lubrication oil. The refurbishment procedure involves using a commercially available degreasing solution which can be pumped into and out of the rack with the objective of removing this sludge. The solution used is sold under the trade name 'Simple Green'. No radioactive material was detected on smear or air samples taken of the work area during the reifurbishment activities and the rack rotates freely in both direction even after eighteen months of operation. The only disadvantage to performing this procedure has been the need to maintain a very aggressive contamination control program when unloading samples from the rack. A very fine particulate material attaches to the outside of tubes used to encapsulate samples. This material can produce contamination levels of 10,000 dpm/100 cm 2 in the worst cases but will typically produce local hot spots on the order of 1000 dpm. (author)

Review of modern double beta decay experiments

Energy Technology Data Exchange (ETDEWEB)

Barabash, A. S., E-mail: barabash@itep.ru [Institute of Theoretical and Experimental Physics (NRC ”Kurchatov Institute”), B. Cheremushkinskaya 25, Moscow (Russian Federation)

2015-10-28

The review of modern experiments on search and studying of double beta decay processes is done. Results of the most sensitive current experiments are discussed. The main attention is paid to EXO-200, KamLAND-Zen, GERDA-I and CUORE-0 experiments. Modern values of T{sub 1/2}(2ν) and best present limits on neutrinoless double beta decay and double beta decay with Majoron emission are presented. Conservative limits on effective mass of a Majorana neutrino (〈m{sub ν}〉 < 0.46 eV) and a coupling constant of Majoron to neutrino (〈g{sub ee}〉 < 1.3 · 10{sup −5}) are obtained. Prospects of search for neutrinoless double beta decay in new experiments with sensitivity to 〈m{sub ν}〉 at the level of ∼ 0.01-0.1 eV are discussed.

Inspection and Analysis of Aluminum Storage Racks in Spent Fuel Storage Basins

International Nuclear Information System (INIS)

Howell, J.P.; Nelson, D.Z.

1998-07-01

Aluminum-clad spent nuclear fuel is stored in water filled basins at the Savannah River Site awaiting processing or other disposition. After more than 35 years of service underwater, the aluminum storage racks that position the fuel bundles in the basin were replaced. During the removal of the racks from the basin, a failure occurred in one of the racks and the Savannah River Technology Center was asked to investigate. This paper presents results of the failure analysis and provides a discussion of the effects of corrosion on the structural integrity of the storage racks

Preparation and planning for the replacement of the Oregon State University TRIGA reactor rotary specimen rack assembly

International Nuclear Information System (INIS)

Anderson, T.V.; Dodd, B.; Johnson, A.G.; Carpenter, W.T.

1984-01-01

Recently there have been a number of indications that the rotating rack may be approaching the end of its useful life. In order to benefit from the experience of other reactors who have removed and replaced their rotating racks, General Atomic (GA) was contacted and previous TRIGA Conference proceedings were scanned. It was determined that a number of facilities, had experienced difficulties with their lazy susans and eventually had to replace them. However, most of the written descriptions of this project were not sufficiently detailed to be of great use. The purpose of this paper is to identify some of the more important questions related to the replacement of our rotating rack assembly and OSU's currently proposed solutions, with a view towards soliciting ideas from other members of the TRIGA reactor community

Rack Aware Data Placement for Network Consumption in Erasure-Coded Clustered Storage Systems

Directory of Open Access Journals (Sweden)

Bilin Shao

2018-06-01

Full Text Available The amount of encoded data replication in an erasure-coded clustered storage system has a great impact on the bandwidth consumption and network latency, mostly during data reconstruction. Aimed at the reasons that lead to the excess data transmission between racks, a rack aware data block placement method is proposed. In order to ensure rack-level fault tolerance and reduce the frequency and amount of the cross-rack data transmission during data reconstruction, the method deploys partial data block concentration to store the data blocks of a file in fewer racks. Theoretical analysis and simulation results show that our proposed strategy greatly reduces the frequency and data volume of the cross-rack transmission during data reconstruction. At the same time, it has better performance than the typical random distribution method in terms of network usage and data reconstruction efficiency.

Rack for storage of nuclear fuel elements

International Nuclear Information System (INIS)

Bosshart, E.

1987-01-01

The rack contains a cluster of parallel, approximately vertical, neutron absorbing square section tubes which are attached to a bottom plate and mutually supported along their edges using welded joining pieces. These welded pieces touch each other laterally in at least one middle plane where the rack is joined. The pieces are additionally secured laterally by screws. Thereby a safe and simple mutual support of the tubes is achieved. It is possible to dismount the tubes by releasing the screws without the necessity to move the tubes in a horizontal direction. 4 figs

Dynamic response of piping system on rack structure with gaps and frictions

International Nuclear Information System (INIS)

Kobayashi, Hiroe; Yoshida, Misutoyo; Ochi, Yoshio

1989-01-01

In the seismic design of a piping system on a rack structure, the interaction between the piping system and the rack structure must be evaluated under the condition that the rack structure is not stiff and heavy enough compared with the piping system. Moreover, there are local nonlinearities due to the gap and friction between the piping system and the rack structure. This paper presents the influence of the interaction and the local nonlinearities upon the seismic response by numerical study and a vibration test using a shaking table. In the numerical study, the piping system and the rack structure were represented by the three degrees of freedom mass-spring model taking a vibration mode of the piping system into account. The nonlinearities due to gap and friction were defined as a function of motion and treated as the pseudo force vector (additional applied force) in an equation of motion. From the results of the numerical study and the vibration test, it was clarified that seismic response of both the rack structure and the piping system is reduced by gap and friction. Moreover, the piping system and rack structure can be represented by the three degrees of freedom mass spring model. And the local nonlinearities can be treated by the pseudo force in an equation of motion. (orig.)

Neutrinoless Double Beta Decay Experiments

International Nuclear Information System (INIS)

Garfagnini, A.

2014-08-01

Neutrinoless double beta decay is the only process known so far able to test the neutrino intrinsic nature: its experimental observation would imply that the lepton number is violated by two units and prove that neutrinos have a Majorana mass components, being their own anti-particle. While several experiments searching for such a rare decay have been per- formed in the past, a new generation of experiments using different isotopes and techniques have recently released their results or are taking data and will provide new limits, should no signal be observed, in the next few years to come. The present contribution reviews the latest public results on double beta decay searches and gives an overview on the expected sensitivities of the experiments in construction which will be able to set stronger limits in the near future. EXO and KamLAND-Zen experiments are based on the decay of Xe 136 , GERDA and MAJORANA experiments are based on the decay of Ge 76 , and the CUORE experiment is based on the decay of Te 130

Effects of suspension of air-conditioning on airtight-type racks.

Science.gov (United States)

Kanzaki, M; Fujieda, M; Furukawa, T

2001-10-01

Although isolation racks are superior to open-type racks in terms of securing breeding conditions for laboratory animals, the contingency-proofing capability of the former has yet to be determined. Therefore, from the view of risk management, we studied the environmental change in isolation racks by forcibly suspending ventilation and air-conditioning and confirming the maximal time length for complete recovery to the original condition after restarting their operations. The isolation racks were placed in a room that was equipped with an independent air-conditioning system. When the inside condition of the racks reached 22-24 degrees C and 59-64% of relative humidity, the air-conditioning and ventilation were forcibly suspended and the subsequent temperature, relative humidity, ammonium and CO2 concentrations in the racks were measured over time. We found that after suspending the air-conditioning and ventilation, it took 40-60 min for temperature, and about 10 min for relative humidity to exceed the maximum values (temperature and relative humidity) referred to in the Showa 58 Nenban Guideline Jikken Doubutsu Shisetsu no Kenchiku oyobi Setsubi (Guidelines of buildings and facilities for experimental animals in Japan; Year 1983 edition). After 17 hr 25 min of the suspension of air-conditioning and ventilation, two rats were found dead. Then, the air-conditioning and ventilation were restarted. It took about 2 hr for temperature, and 50 min for relative humidity to regain the guideline values. The ammonium concentration stayed within the guideline value with a maximum concentration of 2 ppm in the experimental period, whereas the CO2 concentration was found to exceed 9% at the time of animal death.

78 FR 63166 - Certain Kitchen Appliance Shelving and Racks From the People's Republic of China: Countervailing...

Science.gov (United States)

2013-10-23

... Shelving and Racks From the People's Republic of China: Countervailing Duty Administrative Review; 2011... order on certain kitchen appliance shelving and racks (kitchen racks) from the People's Republic of.... Scope of the Order This order covers shelving and racks for refrigerators, freezers, combined...

Influence of Rack Slope and Approaching Conditions in Bottom Intake Systems

Directory of Open Access Journals (Sweden)

Luis G. Castillo

2017-01-01

Full Text Available The study analyzes the flow over bottom racks made of longitudinal T-shaped bars. A clear water flow is considered in a laboratory flume. Free surface profiles, wetted rack lengths, and discharge coefficients are measured, changing parameters such as longitudinal slope, void ratio, and approaching flow. The present work complements existing experimental studies, considering the influence of the approaching flow conditions. The velocity field measured with Particle Image Velocimetry (PIV technique and the pressure field with Pitot tubes are quantified. Numerical simulations (CFD are used to complement laboratory data. The energy head along the rack is calculated and compared with the hypothesis of horizontal energy level with minimum energy at the beginning of the rack. A discharge coefficient adjustment that considers the slope, the void ratio, and the position along the rack is proposed and presented with the results of other works. Theoretical proposals to calculate the pressure field along the flow are compared with measurements in the laboratory. The relation between the static pressure head in the space of bars and the discharge coefficient is used as an alternative method to define the discharge.

The NRC activities concerning Boraflex use in spent-fuel storage racks

International Nuclear Information System (INIS)

Kopp, L.I.

1996-01-01

The U.S. Nuclear Regulatory Commission (NRC) has issued several generic communications to the nuclear industry identifying two issues with respect to using Boraflex in spent-fuel storage racks. The first issue related to gamma-radiation-induced shrinkage of Boraflex and the potential to develop tears or gaps in the material. This phenomenon is typically accounted for in criticality analyses of spent-fuel storage racks. The second issue concerned long-term Boraflex performance throughout the intended service life of the racks as a result of both gamma irradiation and exposure to the wet pool environment

Seismic testing of the base-isolated PWR spent-fuel storage rack

International Nuclear Information System (INIS)

Fujita, Katsuhisa; Tanaka, Mamoru; Nakamura, Masaaki; Tsujikura, Yonezo.

1990-01-01

The present paper aims to verify the seismic safety of the base-isolated spent-fuel storage rack. A series of seismic tests has been conducted using a three-dimensional shaking table. A sliding-type base-isolation system was employed for the prototype rack considering environmental conditions in an actual plant. A non linear seismic response analysis was also performed, and it is verified that the prototype of a base-isolated spent-fuel storage rack has a sufficient seismic safety margin for design seismic conditions from the viewpoint of seismic response. (author)

Engineering analyses of ITER divertor diagnostic rack design

Energy Technology Data Exchange (ETDEWEB)

Modestov, Victor S., E-mail: modestov@compmechlab.com [St Petersburg State Polytechnical University, 195251 St Petersburg, 29 Polytechnicheskaya (Russian Federation); Nemov, Alexander S.; Borovkov, Aleksey I.; Buslakov, Igor V.; Lukin, Aleksey V. [St Petersburg State Polytechnical University, 195251 St Petersburg, 29 Polytechnicheskaya (Russian Federation); Kochergin, Mikhail M.; Mukhin, Eugene E.; Litvinov, Andrey E.; Koval, Alexandr N. [Ioffe Physico-Technical Institute, 194021 St Petersburg, 26 Polytechnicheskaya (Russian Federation); Andrew, Philip [ITER Organization, Route de Vinon sur Verdon, 13115 Saint Paul Lez Durance (France)

2013-10-15

Highlights: • The approach developed early has been used for the assessment of new design of DTS racks and neutron shield units. • Results of most critical EM and seismic analyses indicate that introduced changes significantly improved the system behaviour under these loads. • However further research is required to finalize the design and check it upon meeting all structural, thermal, seismic, EM and fatigue requirements. -- Abstract: The divertor port racks used as a support structure of the divertor Thomson scattering equipment has been carefully analyzed to be consistent with electromagnetic and seismic loads. It follows from the foregoing simulations that namely these analyses demonstrate critical challenges associated with the structure design. Based on the results of the reference structure [2] a modified design of the diagnostic racks is proposed and updated simulation results are given. The results signify a significant improvement over the previous reference layout and the design will be continued towards finalization.

Seismic response of free standing fuel rack construction to 3-D floor motion

International Nuclear Information System (INIS)

Soler, A.I.; Singh, K.

1983-01-01

Seismic analysis of free standing submerged racks is complicated by the presence of water and structural non-linearities such as fuel assembly cell impact and floor interface friction. A direct time integration technique has been proposed to analyze this class of structures. Application of the time integration technique on a fourteen degree of freedom lumped mass model of the rack reveals some heretofore unpublished quirks in the structure's behavior. The method of analysis is utilized to compare the seismic response of some representative rack designs. Results show wide differences in the structural response, depending on the fabrication details of racks

77 FR 61396 - Certain Kitchen Appliance Shelving and Racks From the People's Republic of China: Countervailing...

Science.gov (United States)

2012-10-09

... Shelving and Racks From the People's Republic of China: Countervailing Duty Administrative Review; 2010... order on certain kitchen appliance shelving and racks (``kitchen racks'') from the People's Republic of...-1785, respectively. Scope of the Order The scope of the order consists of shelving and racks for...

76 FR 62364 - Certain Kitchen Appliance Shelving and Racks From the People's Republic of China: Preliminary...

Science.gov (United States)

2011-10-07

... Shelving and Racks From the People's Republic of China: Preliminary Results of the Countervailing Duty... countervailable duty order on certain kitchen appliance shelving and racks (``Kitchen Racks'') from the People's...: Background On July 27, 2009, the Department published a CVD order on Kitchen Racks from the PRC. See Certain...

Replacement of the rotary specimen rack in the U.S. Geological Survey TRIGA Reactor (GSTR)

International Nuclear Information System (INIS)

Rusling, D.H.; Helfer, P.G.; Perryman, R.E.; Smith, W.L.

1986-01-01

A new rotary specimen rack was installed in the GSTR on November 13, 1985. The new rack has been modified to allow the pneumatic unloading of samples. Instructions for the removal and installation of the rotary specimen rack were provided by GA Technologies. The first step was to prepare the core for removal of the control rods, T/C fuel elements, and the central thimble. The rack was weighted prior to removal to ensure that it could not float to the surface. The old rack was stored at the side of the tank. Radiation measurements were made with an underwater ion chamber. (author)

Double-slit experiment in momentum space

Science.gov (United States)

Ivanov, I. P.; Seipt, D.; Surzhykov, A.; Fritzsche, S.

2016-08-01

Young's classic double-slit experiment demonstrates the reality of interference when waves and particles travel simultaneously along two different spatial paths. Here, we propose a double-slit experiment in momentum space, realized in the free-space elastic scattering of vortex electrons. We show that this process proceeds along two paths in momentum space, which are well localized and well separated from each other. For such vortex beams, the (plane-wave) amplitudes along the two paths acquire adjustable phase shifts and produce interference fringes in the final angular distribution. We argue that this experiment can be realized with the present-day technology. We show that it gives experimental access to the Coulomb phase, a quantity which plays an important role in all charged particle scattering but which usual scattering experiments are insensitive to.

Analysis of ICPP fuel storage rack inner tie and corner tie substructures

Energy Technology Data Exchange (ETDEWEB)

Nitzel, M.E.; Rahl, R.G.

1996-01-01

Finite element models were developed and analyses performed for the tie plate, inner tie block assembly, and corner tie block assembly of a 25 port fuel rack assembly designed for installation in Pool 1 of Building 666 at the Idaho Chemical Processing Plant. These models were specifically developed to investigate the adequacy of certain welds joining components of the fuel storage rack assembly. The work scope for the task was limited to an investigation of the stress levels in the subject subassemblies when subjected to seismic loads. Structural acceptance criteria used for the elastic calculations performed were as found in the overall rack design report as issued by the rack`s designer, Holtec International. Structural acceptance criteria used for the plastic calculations performed as part of this effort were as defined in Subsection NF and Appendix F of the ASME Boiler & Pressure Vessel Code. The results of the analyses will also apply to the 30 port fuel storage rack design that is also scheduled for installation in Pool 1 of ICPP 666. The results obtained from the analyses performed for this task indicate that the welds joining the inner tie block and corner tie block to the surrounding rack structure meet the acceptance criteria. Further, the structural members (plates and blocks) were also found to be within the allowable stress limits established by the acceptance criteria. The separate analysis performed on the inner tie plate confirmed the structural adequacy for both the inner tie plate, corner tie plate, and tie block bolts. The analysis results verified that the inner tie and corner tie block should be capable of transferring the expected seismic load without structural failure.

77 FR 21744 - Certain Kitchen Appliance Shelving and Racks From the People's Republic of China: Final Results...

Science.gov (United States)

2012-04-11

... Shelving and Racks From the People's Republic of China: Final Results of the Countervailing Duty... countervailable duty order on certain kitchen appliance shelving and racks (``Kitchen Racks'') from the People's... Kitchen Appliance Shelving and Racks from the People's Republic of China: Preliminary Results of...

Head losses in small hydropower plant trash racks (SHP

Directory of Open Access Journals (Sweden)

N. Walczak

2016-12-01

Full Text Available Small hydropower plants (SHP are technical facilities that are part of alternative energy sources [Paish 2002]. They are primarily characterised by low unit power (in Poland below 5 MW and are often constructed on existing barrages. Electrical current produced by these plants is used to meet local demand. Considering the exploitation of SHPs, it is important to ensure a stable flow through turbines. Aggidis et al. [2010] analysed SHP equipment costs depending on the turbine set. The turbines are protected against damage with trash racks applied for capturing water-borne detritus, such as plant debris carried by water. However, trash racks as solid equipment of SHPs cause head losses, and as a consequence reduce the efficiency of the system. These losses result not only from the spacing of bars, their shape and the technical condition of the inlet chamber, but also from plant debris, its nature, and the quantity of accumulated material that effectively limits the flow. The plant debris captured on trash racks is characterised by diversity in terms of species composition related to the vegetation period and the area where hydraulic facilities are located. Therefore, it is important to maintain trash racks clean by regular removal of the accumulated material. In this context, modernised and newly built power plants are fitted with mechanical cleaners. In older facilities, manual intervention for regular cleaning is required. The present study analyses how the bar shape and the orientation angle of trash racks as well as the accumulated plant debris affect head losses. The results were obtained from laboratory tests. The research examined the impact the inclination angle of trash racks (30°, 60° and 80° has on head loss values for three different shapes of bars (cylindrical, angled and flat rectangular and various weight portions of plant debris (0.25, 0.375 and 0.5 kg. The summarised losses were determined by measuring the difference in water

White House Communications Agency (WHCA) Presidential Voice Communications Rack Mount System Mechanical Drawing Package

Science.gov (United States)

2015-12-01

Rack Mount System Mechanical Drawing Package by Steven P Callaway Approved for public release; distribution unlimited...Laboratory White House Communications Agency (WHCA) Presidential Voice Communications Rack Mount System Mechanical Drawing Package by Steven P...Note 3. DATES COVERED (From - To) 04/2013 4. TITLE AND SUBTITLE White House Communications Agency (WHCA) Presidential Voice Communications Rack

A new electronic circuit for NIM rack power supply

International Nuclear Information System (INIS)

Toledo, Fabio de; Domienikan, Claudio; Zahn, Guilherme S.

2013-01-01

A new and useful electronic circuit designed to substitute the old power supply of IPEN model PM 1212 Nuclear Instrument Modules (NIM) racks is presented. Originally, these NIM racks were projected by IPEN workshop at 1974 to be used in nuclear research laboratories. The PM1212 provided mounting space and power sources for up to 12 standard nuclear electronic modules and power supply regulated DC voltages of ±24V (2A), ±12V (4A) and unregulated AC 117V (0.5A). Currently, several of these NIM racks are not in use because the electronic components of the original design have become obsolete and are no longer manufactured. The new electronic circuit provides the same original voltages adjusted in the single circuit and, additionally, ±6V. The new power supply was designed and constructed at IPEN-CNEN/SP by employing modern national components and expertise. (author)

A new electronic circuit for NIM rack power supply

Energy Technology Data Exchange (ETDEWEB)

Toledo, Fabio de; Domienikan, Claudio; Zahn, Guilherme S., E-mail: fatoledo@ipen.br, E-mail: clanikan@ipen.br, E-mail: gzahn@ipen.br [Intituto de Pesquisas Energeticas e Nucleares (IPEN-CNEN/SP), Sao Paulo, SP (Brazil)

2013-07-01

A new and useful electronic circuit designed to substitute the old power supply of IPEN model PM 1212 Nuclear Instrument Modules (NIM) racks is presented. Originally, these NIM racks were projected by IPEN workshop at 1974 to be used in nuclear research laboratories. The PM1212 provided mounting space and power sources for up to 12 standard nuclear electronic modules and power supply regulated DC voltages of ±24V (2A), ±12V (4A) and unregulated AC 117V (0.5A). Currently, several of these NIM racks are not in use because the electronic components of the original design have become obsolete and are no longer manufactured. The new electronic circuit provides the same original voltages adjusted in the single circuit and, additionally, ±6V. The new power supply was designed and constructed at IPEN-CNEN/SP by employing modern national components and expertise. (author)

A Study on Criticality Safety Parameters of New Fuel Storage Rack Design

International Nuclear Information System (INIS)

Ahn, Joon Gi; Kim, Hyeong Heon

2012-01-01

The dry new fuel storage rack shall maintain the subcritical condition (i.e., k-eff < 0.95) when fully flooded with water and the k-eff will not exceed 0.98 even assuming that the optimum moderation causes the highest reactivity. Thus, the design parameters of the new fuel rack are determined optimally by considering both the full density water flooding condition and the optimum moderation condition. The behavior of the keff as the variation of design parameter of the new fuel rack was investigated as the function of the moderating water density

A Study on Criticality Safety Parameters of New Fuel Storage Rack Design

Energy Technology Data Exchange (ETDEWEB)

Ahn, Joon Gi; Kim, Hyeong Heon [KEPCO E and C, Daejeon (Korea, Republic of)

2012-05-15

The dry new fuel storage rack shall maintain the subcritical condition (i.e., k-eff < 0.95) when fully flooded with water and the k-eff will not exceed 0.98 even assuming that the optimum moderation causes the highest reactivity. Thus, the design parameters of the new fuel rack are determined optimally by considering both the full density water flooding condition and the optimum moderation condition. The behavior of the keff as the variation of design parameter of the new fuel rack was investigated as the function of the moderating water density

Melting of fuel element racks and their recycling as granulate

International Nuclear Information System (INIS)

Quade, U.; Kluth, T.; Kreh, R.

1998-01-01

In order to increase the storage capacity for spent fuel elements in the Spanish NPPs of Almaraz and Asco, the existing racks were replaced by compact one in 1991/1993. The 28 racks from Almaraz NPP were cut on site, packed in 200-I-drums and taken to intermediate storage. For the remaining 28 racks of Asco NPP, ENRESA preferred the melting alternative. To demonstrate the recycling path melting in Germany, a test campaign with six racks was performed in 1997. As a result of this test melt, the limits for Carla melting plant were modified to 200 Bq/g total, α, β, γ 100 Bq/g nuclear fuels, max. 3g/100 kg 2,000 Bq/g total Fe55, H 3 , C-14 and Ni63. After the test melt campaign, the German authorities licensed the import and treatment of the remaining 22 racks on the condition that the waste resulting from the melting process as well as the granules produced were taken back to Spain. The shipment from Asco via France to Germany has been carried out in F 20-ft-IPII containers in accordance with ADR. Size reduction to chargeable dimensions was carried out by a plasma burner and hydraulic shears. For melting, a 3.2 Mg medium frequency induction furnace, operated in a separate housing, was used. For granules production outside this housing, the liquid iron was cast into a 5Mg ladle and then, through a water jet, into the granulating basin. The total mass of 287,659 Kg of 28 fuel elements racks and components of the storage basin yielded 297,914 kg of iron granulate. Secondary waste from melting amounted to 9,920 kg, corresponding to 3.45% of the input mass. The granulating process produced 6,589 kg, corresponding to 2.28% of the total mass to be melted. Radiological analysis of samples taken from the melt and different waste components confirmed the main nuclides Co60, Cs134 and Cs137. Fe55 was highly overestimated by the preliminary analysis. (Author) 2 refs

26 CFR 48.4081-2 - Taxable fuel; tax on removal at a terminal rack.

Science.gov (United States)

2010-04-01

... 26 Internal Revenue 16 2010-04-01 2010-04-01 true Taxable fuel; tax on removal at a terminal rack..., Tread Rubber, and Taxable Fuel Taxable Fuel § 48.4081-2 Taxable fuel; tax on removal at a terminal rack... rack are subject to tax and the position holder with respect to the fuel is liable for the tax. (b...

40 CFR Table 2 to Subpart Bbbbbb... - Applicability Criteria, Emission Limits, and Management Practices for Loading Racks

Science.gov (United States)

2010-07-01

... Limits, and Management Practices for Loading Racks 2 Table 2 to Subpart BBBBBB of Part 63 Protection of... Criteria, Emission Limits, and Management Practices for Loading Racks If you own or operate Then you must 1. A gasoline loading rack(s) at a bulk gasoline terminal with a gasoline throughput of 250,000 gallons...

Surveillance of a Ventilated Rack System for Corynebacterium bovis by Sampling Exhaust-Air Manifolds.

Science.gov (United States)

Manuel, Christopher A; Pugazhenthi, Umarani; Leszczynski, Jori K

2016-01-01

Corynebacterium bovis causes an opportunistic infection of nude (Foxn1, nu/nu) mice, leading to nude mouse hyperkeratotic dermatitis (scaly skin disease). Enzootic in many nude mouse colonies, C. bovis spreads rapidly to naive nude mice, despite modern husbandry practices, and is very difficult to eradicate. To facilitate rapid detection in support of eradication efforts, we investigated a surveillance method based on quantitative real-time PCR (qPCR) evaluation of swabs collected from the horizontal exhaust manifold (HEM) of an IVC rack system. We first evaluated the efficacy of rack sanitation methods for removing C. bovis DNA from the HEM of racks housing endemic colonies of infected nude mice. Pressurized water used to flush the racks' air exhaust system followed by a standard rack-washer cycle was ineffective in eliminating C. bovis DNA. Only after autoclaving did all sanitized racks test negative for C. bovis DNA. We then measured the effects of stage of infection (early or established), cage density, and cage location on the rack on time-to-detection at the HEM. Stage of infection significantly affected time-to-detection, independent of cage location. Early infections required 7.3 ± 1.2 d whereas established infections required 1 ± 0 d for detection of C. bovis at the HEM. Cage density influenced the quantity of C. bovis DNA detected but not time-to-detection. The location of the cage on the rack affected the time-to-detection only during early C. bovis infections. We suggest that qPCR swabs of HEM are useful during the routine surveillance of nude mouse colonies for C. bovis infection.

Depletion of WRN protein causes RACK1 to activate several protein kinase C isoforms

DEFF Research Database (Denmark)

Massip, L; Garand, C; Labbé, A

2010-01-01

show that a knock down of the WRN protein in normal human fibroblasts induces phosphorylation and activation of several protein kinase C (PKC) enzymes. Using a tandem affinity purification strategy, we found that WRN physically and functionally interacts with receptor for activated C-kinase 1 (RACK1......), a highly conserved anchoring protein involved in various biological processes, such as cell growth and proliferation. RACK1 binds strongly to the RQC domain of WRN and weakly to its acidic repeat region. Purified RACK1 has no impact on the helicase activity of WRN, but selectively inhibits WRN exonuclease...... activity in vitro. Interestingly, knocking down RACK1 increased the cellular frequency of DNA breaks. Depletion of the WRN protein in return caused a fraction of nuclear RACK1 to translocate out of the nucleus to bind and activate PKCdelta and PKCbetaII in the membrane fraction of cells. In contrast...

Random Access Frames (RAF): Alternative to Rack and Standoff for Deep Space Habitat Outfitting

Science.gov (United States)

Howe, A. Scott; Polit-Casillas, Raul

2014-01-01

A modular Random Access Frame (RAF) system is proposed as an alternative to the International Standard Payload Rack (ISPR) for internal module layout and outfitting in a Deep Space Habitat (DSH). The ISPR approach was designed to allow for efficient interchangeability of payload and experiments for the International Space Station (ISS) when frequent resupply missions were available (particularly the now-retired Space Shuttle). Though the standard interface approach to the ISPR system allowed integration of subsystems and hardware from a variety of sources and manufacturers, the heavy rack and standoff approach may not be appropriate when resupply or swap-out capabilities are not available, such as on deep space, long-duration missions. The lightweight RAF concept can allow a more dense packing of stowage and equipment, and may be easily broken down for repurposing or reuse. Several example layouts and workstations are presented.

ISS Payload Racks Automated Flow Control Calibration Method

Science.gov (United States)

Simmonds, Boris G.

2003-01-01

Payload Racks utilize MTL and/or LTL station water for cooling of payloads and avionics. Flow control range from valves of fully closed, to up to 300 Ibmhr. Instrument accuracies are as high as f 7.5 Ibm/hr for flow sensors and f 3 Ibm/hr for valve controller, for a total system accuracy of f 10.5 Ibm/hr. Improved methodology was developed, tested and proven that reduces accuracy of the commanded flows to less than f 1 Ibmhr. Uethodology could be packed in a "calibration kit" for on- orbit flow sensor checkout and recalibration, extending the rack operations before return to earth. -

78 FR 54450 - Certain Kitchen Appliance Shelving and Racks From the People's Republic of China: Preliminary...

Science.gov (United States)

2013-09-04

... Shelving and Racks From the People's Republic of China: Preliminary Results of Antidumping Duty... the antidumping duty order on certain kitchen appliance shelving and racks from the People's Republic...\\ is certain kitchen appliance shelving and racks. The subject merchandise is currently classifiable...

The fabrication of plastic cages for suspension in mass air flow racks.

Science.gov (United States)

Nielsen, F H; Bailey, B

1979-08-01

A cage for suspension in mass air flow racks was constructed of plastic and used to house rats. Little or no difficulty was encountered with the mass air flow rack-suspended cage system during the 4 years it was used for the study of trace elements.

Entering 'A NEW REALM' of KIBO Payload Operations - Continuous efforts for microgravity experiment environment and lessons learned from real time experiment operations in KIBO -

International Nuclear Information System (INIS)

Sakagami, K; Goto, M; Matsumoto, S; Ohkuma, H

2011-01-01

On January 22nd, 2011(JST), KOUNOTORI2 (H-II Transfer Vehicle: HTV2) was successfully launched from Tanegashima Space Center toward the International Space Station (ISS) and two new JAXA payload racks, Kobairo rack and MSPR (Multi-purpose Small Payload Rack) were transferred to ISS/KIBO (Japanese Experiment Module: JEM). In addition to Saibo rack and Ryutai rack which are already in operation in KIBO, in total 4 Japanese experiment payload racks start operations in KIBO. Then KIBO payload operations embark on a new realm, full utilization phase. While the number and variety of microgravity experiments become increasing, simultaneous operation constraints should be considered to achieve multitask payload operations in ISS/KIBO and ever more complicated cooperative operations between crewmember and flight control team/science team are required. Especially for g-jitter improvement in ISS/KIBO, we have greatly advanced cooperative operations with crewmember in the recent increment based on the microgravity data analysis results. In this paper, newly operating Japanese experiment payloads characteristics and some methods to improve g-jitter environment are introduced from the front line of KIBO payload operations.

77 FR 72324 - Certain Kitchen Appliance Shelving and Racks from the People's Republic of China: Countervailing...

Science.gov (United States)

2012-12-05

... Shelving and Racks from the People's Republic of China: Countervailing Duty Administrative Review, 2010... countervailing duty order on certain kitchen appliance shelving and racks from the People's Republic of China. See Certain Kitchen Appliance Shelving and Racks From the People's Republic of China: Countervailing...

Kale BoRACK1 is involved in the plant response to salt stress and Peronospora brassicae Gaumann.

Science.gov (United States)

Li, Da-Hong; Shen, Fu-Jia; Li, Hong-Yan; Li, Wei

2017-06-01

The receptor for activated C kinase 1 (RACK1) belongs to a protein subfamily containing a tryptophan-aspartic acid-domain (WD) repeat structure. Compelling evidence indicates that RACK1 can interact with many signal molecules and affect different signal transduction pathways. In this study, a kale (Brassica oleracea var. acephala f.tricolor) RACK1 gene (BoRACK1) was cloned by RT-PCR. The amino acid sequence of BoRACK1 had seven WD repeats in which there were typical GH (glycine-histidine) and WD dipeptides. Comparison with AtRACK1 from Arabidopsis revealed 87.1% identity at the amino acid level. Expression pattern analysis by RT-PCR showed that BoRACK1 was expressed in all analyzed tissues of kale and that its transcription in leaves was down-regulated by salt, abscisic acid, and H 2 O 2 at a high concentration. Overexpression of BoRACK1 in kale led to a reduction in symptoms caused by Peronospora brassicae Gaumann on kale leaves. The expression levels of the pathogenesis-related protein genes, PR-1 and PRB-1, increased 2.5-4-fold in transgenic kale, and reactive oxygen species production was more active than in the wild-type. They also exhibited increased tolerance to salt stress in seed germination. H 2 O 2 may also be involved in the regulation of BoRACK1 during seed germination under salt stress. Quantitative real-time PCR analyses showed that the transcript levels of BoRbohs genes were significantly higher in overexpression of BoRACK1 transgenic lines. Yeast two-hybrid assays showed that BoRACK1 could interact with WNK8, eIF6, RAR1, and SGT1. This study and previous work lead us to believe that BoRACK1 may form a complex with regulators of plant salt and disease resistance to coordinate kale reactions to pathogens. Copyright © 2017 Elsevier GmbH. All rights reserved.

77 FR 61385 - Certain Kitchen Appliance Shelving and Racks From the People's Republic of China: Antidumping...

Science.gov (United States)

2012-10-09

... Shelving and Racks From the People's Republic of China: Antidumping Duty Administrative Review, 2010-2011... administrative review of the antidumping duty order on certain kitchen appliance shelving and racks from the... INFORMATION: Scope of the Order The scope of this order consists of shelving and racks for refrigerators...

77 FR 12811 - Certain Kitchen Appliance Shelving and Racks From the People's Republic of China: Partial...

Science.gov (United States)

2012-03-02

... Shelving and Racks From the People's Republic of China: Partial Rescission of Antidumping Duty... review of the antidumping duty order on certain kitchen appliance shelving and racks from the People's... Appliance Shelving and Racks from the People's Republic of China, dated January 10, 2012; and Letter to the...

76 FR 62765 - Certain Kitchen Appliance Shelving and Racks From the People's Republic of China: Preliminary...

Science.gov (United States)

2011-10-11

... Shelving and Racks From the People's Republic of China: Preliminary Results of the First Administrative... review of the antidumping duty order on certain kitchen appliance shelving and racks from the People's... administrative review of certain kitchen appliance shelving and racks from the PRC for the period March 5, 2009...

26 CFR 48.4081-3 - Taxable fuel; taxable events other than removal at the terminal rack.

Science.gov (United States)

2010-04-01

... at the terminal rack. 48.4081-3 Section 48.4081-3 Internal Revenue INTERNAL REVENUE SERVICE...; taxable events other than removal at the terminal rack. (a) Overview. Although tax is imposed when taxable fuel is removed from the terminal at the rack, tax also is imposed in certain other situations...

Status of the Double Chooz experiment

Energy Technology Data Exchange (ETDEWEB)

Gonzalez, L.F.G. [Universidade Estadual de Campinas (IFGW/UNICAMP), SP (Brazil). Inst. de Fisica Gleb Wataghin. Dept. de Raios Cosmicos e Cronologia; Universite Oaris Diderot (France); Kemp, E. [Universidade Estadual de Campinas (IFGW/UNICAMP), SP (Brazil). Inst. de Fisica Gleb Wataghin. Dept. de Raios Cosmicos e Cronologia; Anjos, J.C. dos; Barbosa, A.F.; Lima Junior, H.P.; Gama, R.; Abrahao, T.; Pepe, I.M. [Centro Brasileiro de Pesquisas Fisicas (CBPF), Rio de Janeiro, RJ (Brazil); Chimenti, P. [Universidade Federal do ABC (UFABC), SP (Brazil)

2011-07-01

Full text: The neutrino oscillation experiment Double Chooz, located at the nuclear power plant of Chooz (Ardennes, France), has as purpose to measure the mixing angle {theta}{sub 13} with greater precision than the measurement of its predecessor, the Chooz experiment. In four years of data acquisition, we expect to decrease the current limit of sin{sup 2}(2{theta}{sub 13}) from 0.2 to 0.03, contributing for the determination of this parameter that is still open in the neutrino mixing matrix. For this, the Double Chooz experiment will use antineutrinos generated in both Chooz plant reactors and will make high accuracy measurements of the flux in two different distances with identical detectors. The first detector (the 'far detector') is already in operation since January 2011 and the construction of the second one (the'{sup n}ear detector') should be completed on the beginning of 2012. Thus, in this work we present the main aspects of this neutrino oscillation experiment and preliminary results of the detector performance. (author)

16 CFR Figure 3 to Part 1610 - Specimen Holder Supported in Specimen Rack

Science.gov (United States)

2010-01-01

... 16 Commercial Practices 2 2010-01-01 2010-01-01 false Specimen Holder Supported in Specimen Rack 3 Figure 3 to Part 1610 Commercial Practices CONSUMER PRODUCT SAFETY COMMISSION FLAMMABLE FABRICS ACT... Holder Supported in Specimen Rack ER25MR08.002 ...

IFBA credit in the Shearon Harris fuel racks with Vantage 5 fuel

International Nuclear Information System (INIS)

Boyd, W.A.; Schmidt, R.F.; Erwin, R.D.

1989-01-01

At the Shearon Harris nuclear plant, fuel management strategies are being considered which will result in feed fuel enrichments approaching 5.0 w/o U-235. These types of enrichments require a new criticality analysis to raise the existing fuel rack enrichment limit. It is receiving Westinghouse Vantage 5 fuel with integral fuel burnable absorber (IFBA) rods providing the depletable neutron absorber. An analysis was performed on the fuel racks which demonstrates that fuel enriched up to 5.0 w/o U-235 can be stored by taking credit for the IFBA rods present in the high enriched fuel assemblies. This is done by calculating the maximum Vantage 5 fuel assembly reactivity that can be placed in the fuel racks and meet the criticality K-eff limit. A methodology is also developed which conservatively calculates the minimum number of IFBA rods needed per assembly to meet the fuel rack storage limits. This eliminates the need for core designers to determine assembly K-inf terms for every different enrichment/IFBA combination

Tests and calculations on a scale one spent fuel storage rack

International Nuclear Information System (INIS)

Moudrik, R.; Queval, J.C.; Gantenbein, F.; Trollat, C.

1995-01-01

This paper deals with the behaviour of racks of PWR reactor (pressurized water reactor) set in a pool, in case of an earthquake. Several parameters are taken into account: fluid, loading, gaps,... The paper presents some tests that can be implemented on the racks, in order to valid them before use. Moreover, a program and the results are presented, as well as calculation. (TEC). 2 refs., 9 figs

78 FR 21594 - Certain Kitchen Appliance Shelving and Racks From the People's Republic of China: Final Results...

Science.gov (United States)

2013-04-11

... Shelving and Racks From the People's Republic of China: Final Results of Countervailing Duty Administrative... countervailing duty (``CVD'') order on certain kitchen appliance shelving and racks from the People's Republic of...\\ See Certain Kitchen Appliance Shelving and Racks From the People's Republic of China: Countervailing...

78 FR 78815 - Certain Kitchen Appliance Shelving and Racks from the People's Republic of China: Rescission of...

Science.gov (United States)

2013-12-27

... Shelving and Racks from the People's Republic of China: Rescission of Antidumping Duty Administrative... administrative review of the antidumping duty order on certain kitchen appliance shelving and racks from the... on certain kitchen appliance shelving and racks from the PRC.\\1\\ On September 30, 2013, the...

77 FR 21734 - Certain Kitchen Appliance Shelving and Racks From the People's Republic of China: Final Results...

Science.gov (United States)

2012-04-11

... Shelving and Racks From the People's Republic of China: Final Results and Partial Rescission of First... duty order on certain kitchen appliance shelving and racks from the People's Republic of China (``PRC... Certain Kitchen Appliance Shelving and Racks From the People's Republic of China: Preliminary Results of...

Dioxin modulates expression of receptor for activated C kinase (RACK-1) in developing neurons

Energy Technology Data Exchange (ETDEWEB)

Yang, J.H.; Kim, S.Y.; Lee, H.G.; Kim, M.Y.; Lee, J.H.; Chae, W.G. [Catholic Univ. of Daegu, Dept. of Pharmacology/Toxicology, Daegu (Korea)

2004-09-15

TCDD is sensitive to the central nerve system of the developing brain. The TCDD-induced neurodevelopmental deficits include the cognitive disability and motor dysfunction. While TCDD may lead to neurodevelopmental and neurobehavioral deficit, it is not known which molecular substances are intracellular targets for TCDD. Since TCDD accumulates in brain and the brain contains the Ah receptor, it is possible that TCDD may act at the target site such as cerebellum, which is responsible for cognitive abilities and motor function. A recent in vitro studies using cerebellar granule cells demonstrated a translocation of PKC-{alpha} and {epsilon} following the TCDD or PCB exposure. One of the most pivotal second messenger molecules involved in neuronal function and development is protein kinase C (PKC). PKC signaling pathways have been implicated as an important factor in learning and memory processes. PKC signaling events are optimized by the adaptor proteins, which organize PKCs near their selective substrates and away from others. RACK-1(receptor for activated C-kinase) is one of adaptor proteins that anchor the activated PKC at the site of translocation 6. RACKs bind PKC only in the presence of PKC activators. RACKs are 30- and 36-kDa proteins located in cytoskeletal compartment and play a key role in PKC activation and in membrane amchoring. Since different PKC isoforms translocate to distinct subcellular sites on activation, it is suggested that isoform-specific RACK may be present. Activation of certain PKC isoforms (PKC-a and {beta}II) is preferentially associated with RACK-1. While TCDD modulates PKC signaling pathway, role of RACK-1 on TCDD-mediated signaling pathway is not known. To identify the intracellular target for TCDD and understand a mechanism of signaling pathway in the developing brain, the present study attempted to analyze effects of RACK-1 in the cerebellar granule cells following TCDD exposure.

77 FR 82 - Certain Kitchen Appliance Shelving and Racks From the People's Republic of China: Extension of...

Science.gov (United States)

2012-01-03

... Shelving and Racks From the People's Republic of China: Extension of Time Limit for the Final Results of... administrative review of the countervailing duty order on certain kitchen appliance shelving and racks from the... Kitchen Appliance Shelving and Racks From the People's Republic of China: Preliminary Results of the...

78 FR 5414 - Certain Kitchen Appliance Shelving and Racks From the People's Republic of China; 2010-2011...

Science.gov (United States)

2013-01-25

... Shelving and Racks From the People's Republic of China; 2010-2011; Final Results of Antidumping Duty... of the antidumping duty order on certain kitchen appliance shelving and racks from the People's... September 1, 2010, through August 31, 2011. \\1\\ See Certain Kitchen Appliance Shelving and Racks From the...

77 FR 22559 - Certain Kitchen Appliance Shelving and Racks From the People's Republic of China: Extension of...

Science.gov (United States)

2012-04-16

... Shelving and Racks From the People's Republic of China: Extension of Time Limit for the Preliminary Results... administrative review of the antidumping duty order on certain kitchen appliance shelving and racks from the... Appliance Shelving and Racks from the People's Republic of China: Selection of an Additional Mandatory...

76 FR 20950 - Certain Kitchen Appliance Shelving and Racks From the People's Republic of China: Extension of...

Science.gov (United States)

2011-04-14

... Shelving and Racks From the People's Republic of China: Extension of Time Limits for the Preliminary... appliance shelving and racks from the People's Republic of China (``PRC'') for the period March 5, 2009... Racks from the People's Republic of China,'' dated January 20, 2011. The Department sent its antidumping...

Definition of a RACK1 Interaction Network in Drosophila melanogaster Using SWATH-MS.

Science.gov (United States)

Kuhn, Lauriane; Majzoub, Karim; Einhorn, Evelyne; Chicher, Johana; Pompon, Julien; Imler, Jean-Luc; Hammann, Philippe; Meignin, Carine

2017-07-05

Receptor for Activated protein C kinase 1 (RACK1) is a scaffold protein that has been found in association with several signaling complexes, and with the 40S subunit of the ribosome. Using the model organism Drosophila melanogaster , we recently showed that RACK1 is required at the ribosome for internal ribosome entry site (IRES)-mediated translation of viruses. Here, we report a proteomic characterization of the interactome of RACK1 in Drosophila S2 cells. We carried out Label-Free quantitation using both Data-Dependent and Data-Independent Acquisition (DDA and DIA, respectively) and observed a significant advantage for the Sequential Window Acquisition of all THeoretical fragment-ion spectra (SWATH) method, both in terms of identification of interactants and quantification of low abundance proteins. These data represent the first SWATH spectral library available for Drosophila and will be a useful resource for the community. A total of 52 interacting proteins were identified, including several molecules involved in translation such as structural components of the ribosome, factors regulating translation initiation or elongation, and RNA binding proteins. Among these 52 proteins, 15 were identified as partners by the SWATH strategy only. Interestingly, these 15 proteins are significantly enriched for the functions translation and nucleic acid binding. This enrichment reflects the engagement of RACK1 at the ribosome and highlights the added value of SWATH analysis. A functional screen did not reveal any protein sharing the interesting properties of RACK1, which is required for IRES-dependent translation and not essential for cell viability. Intriguingly however, 10 of the RACK1 partners identified restrict replication of Cricket paralysis virus (CrPV), an IRES-containing virus. Copyright © 2017 Kuhn et al.

40 CFR Table 5 to Subpart Ffff of... - Emission Limits and Work Practice Standards for Transfer Racks

Science.gov (United States)

2010-07-01

... Standards for Transfer Racks 5 Table 5 to Subpart FFFF of Part 63 Protection of Environment ENVIRONMENTAL... Limits and Work Practice Standards for Transfer Racks As required in § 63.2475, you must meet each emission limit and work practice standard in the following table that applies to your transfer racks: For...

Implications of natural occlusion of ventilated racks on ammonia and sanitation practices.

Science.gov (United States)

Creamer, Michelle A; Petty, Joann; Martin, Tara; Bergdall, Valerie; Hickman-Davis, Judy M

2014-03-01

Examination of ventilated rat racks prior to semiannual sanitation revealed silicone nozzles and ventilation ports that were partially or completely occluded with granular debris. We subsequently sought to document performance standards for rack sanitation and investigate the effect of ventilation port occlusion on rack function and animal husbandry practices. We hypothesized that individually ventilated cages with occluded airflow would require more frequent cage changes, comparable to those for static cages (that is, every 3 to 4 d). Sprague-Dawley rats were housed under one of 4 conditions: no airflow occlusion, occluded air-supply inlet, occluded air-exhaust outlet, and occlusion of both inlet and outlet. Cages were changed when daily ammonia concentration exceeded 20 ppm or after 14 d had elapsed. Most cages with unoccluded or partial airflow occlusion remained below the 20 ppm limit until day 12 or 13. Cages with occlusion of both inlet and outlet exceeded 20 ppm ammonia by as early as day 5. Airflow was significantly lower in cages with occlusion of both inlet and outlet airflow. Weekly inspection revealed that occlusion of ventilation ports was detectable by 3 mo after semiannual sanitation. This study demonstrates that silicone nozzles should be removed prior to rack sanitation to improve the effectiveness of cleaning ventilation ports and nozzles. While the rack is in use, silicone nozzles and ventilation ports should be inspected regularly to identify occlusion that is likely to diminish environmental quality in the cage. Intracage ammonia levels are significantly higher when both inlet and outlet airflow are occluded.

76 FR 27990 - Certain Kitchen Shelving and Racks From the People's Republic of China: Extension of Time Limit...

Science.gov (United States)

2011-05-13

... Racks From the People's Republic of China: Extension of Time Limit for Preliminary Results of... countervailing duty order on certain kitchen appliance shelving and racks from the People's Republic of China... the Countervailing Duty Administrative Review of Certain Kitchen Appliance Shelving and Racks from the...

TCR triggering induces the formation of Lck-RACK1-actinin-1 multiprotein network affecting Lck redistribution

Directory of Open Access Journals (Sweden)

Ondrej Ballek

2016-10-01

Full Text Available The initiation of T-cell signaling is critically dependent on the function of the member of Src family tyrosine kinases (SFKs, Lck. Upon TCR triggering, Lck kinase activity induces the nucleation of signal-transducing hubs that regulate the formation of complex signaling network and cytoskeletal rearrangement. In addition, the delivery of Lck function requires rapid and targeted membrane redistribution, but the mechanism underpinning this process is largely unknown. To gain insight into this process, we considered previously described proteins that could assist in this process via their capacity to interact with kinases and regulate their intracellular translocations. An adaptor protein, Receptor for Activated C Kinase 1 (RACK1, was chosen as a viable option and its capacity to bind Lck and aid the process of activation-induced redistribution of Lck was assessed. Our microscopic observation showed that T-cell activation induces a rapid, concomitant and transient co-redistribution of Lck and RACK1 into the forming immunological synapse. Consistent with this observation, the formation of transient RACK1-Lck complexes were detectable in primary CD4+ T-cells with their maximum levels peaking 10 seconds after TCR-CD4 co-aggregation. Moreover, RACK1 preferentially binds to a pool of kinase active pY394Lck which co-purifies with high molecular weight cellular fractions. The formation of RACK1-Lck complexes depends on functional SH2 and SH3 domains of Lck and includes several other signaling and cytoskeletal elements that transiently bind the complex. Notably, the F-actin-crosslinking protein, α-actinin-1, binds to RACK1 only in the presence of kinase active Lck suggesting that the formation of RACK1-pY394Lck-α-actinin-1 complex serves as a signal module coupling actin cytoskeleton bundling with productive TCR/CD4 triggering. In addition, the treatment of CD4+ T-cells with nocodazole, which disrupts the microtubular network, also blocked the formation

Test Rack Development for Extended Operation of Advanced Stirling Convertors at NASA Glenn Research Center

Science.gov (United States)

Dugala, Gina M.

2010-01-01

The U.S. Department of Energy, Lockheed Martin Space Systems Company, Sunpower Inc., and NASA Glenn Research Center (GRC) have been developing an Advanced Stirling Radioisotope Generator (ASRG) for use as a power system on space science missions. This generator will make use of free-piston Stirling convertors to achieve higher conversion efficiency than with currently available alternatives. One part of NASA GRC's support of ASRG development includes extended operation testing of Advanced Stirling Convertors (ASCs) developed by Sunpower Inc. and GRC. The ASC consists of a free-piston Stirling engine integrated with a linear alternator. NASA GRC has been building test facilities to support extended operation of the ASCs for several years. Operation of the convertors in the test facility provides convertor performance data over an extended period of time. One part of the test facility is the test rack, which provides a means for data collection, convertor control, and safe operation. Over the years, the test rack requirements have changed. The initial ASC test rack utilized an alternating-current (AC) bus for convertor control; the ASRG Engineering Unit (EU) test rack can operate with AC bus control or with an ASC Control Unit (ACU). A new test rack is being developed to support extended operation of the ASC-E2s with higher standards of documentation, component selection, and assembly practices. This paper discusses the differences among the ASC, ASRG EU, and ASC-E2 test racks.

Evaluation of AMPX-KENO benchmark calculations for high-density spent fuel storage racks

International Nuclear Information System (INIS)

Turner, S.E.; Gurley, M.K.

1981-01-01

The AMPX-KENO computer code package is commonly used to evaluate criticality in high-density spent fuel storage rack designs. Consequently, it is important to know the reliability that can be placed on such calculations and whether or not the results are conservative. This paper evaluates a series of AMPX-KENO calculations which have been made on selected critical experiments. The results are compared with similar analyses reported in the literature by the Oak Ridge National Laboratory and BandW. 8 refs

Seismic evaluation of BWR spent fuel storage racks using actual damping by vibration test in water

International Nuclear Information System (INIS)

Yamasaki, Hiroto; Iwakura, Shigeyoshi; Imaoka, Tetsuo; Okumura, Kazue; Orita, Syuichi; Namita, Yoshio

2010-01-01

Damping value for BWR spent fuel storage racks has been used 1 percent damping, which is applied to welded steel structures in air as defined JEAG4601. However, it is considered that the actual damping is higher than that of the above mentioned, because of its underwater installation. This report shows the actual damping value of the Check Arrayed Rack by vibration test in water and Evaluation by the analysis of rack using actual damping. (author)

40 CFR Table 3 to Subpart Eeee of... - Operating Limits-High Throughput Transfer Racks

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 12 2010-07-01 2010-07-01 true Operating Limits-High Throughput Transfer Racks 3 Table 3 to Subpart EEEE of Part 63 Protection of Environment ENVIRONMENTAL PROTECTION... Throughput Transfer Racks As stated in § 63.2346(e), you must comply with the operating limits for existing...

Remote inspection of the IFSF spent fuel storage rack

International Nuclear Information System (INIS)

Uldrich, E.D.

1996-01-01

The Irradiated Fuel Storage Facility (IFSF) is a dry storage facility for spent nuclear fuels located at the Idaho Chemical Processing Plant; it was constructed in the 1970's specifically for the Fort Saint Vrain spent reactor fuels. Currently, it is being used for various spent fuels. It was not known if IFSF would met current DOE seismic criteria, so re-analysis was started, with the rack being analyzed first. The rack was inspected to determine the as-built condition. LazrLyne and VideoRuler were used in lieu of using a tape measure with the camera. It was concluded that when a visual inspection shows widely varying weld sizes, the engineer has to use all resources available to determine the most probable specified weld sizes

The scaffold protein RACK1 is a target of endocrine disrupting chemicals (EDCs) with important implication in immunity

Energy Technology Data Exchange (ETDEWEB)

Buoso, Erica; Galasso, Marilisa; Ronfani, Melania [Dipartimento di Scienze del Farmaco, Università degli Studi di Pavia, Viale Taramelli 12/14, 27100 Pavia (Italy); Papale, Angela; Galbiati, Valentina [Laboratory of Toxicology, Dipartimento di Scienze Farmacologiche e Biomolecolari, Università degli Studi di Milano, Via Balzaretti 9, 20133 Milano (Italy); Eberini, Ivano [Laboratorio di Biochimica e Biofisica Computazionale, Dipartimento di Scienze Farmacologiche e Biomolecolari, Università degli Studi di Milano, Milan (Italy); Marinovich, Marina [Laboratory of Toxicology, Dipartimento di Scienze Farmacologiche e Biomolecolari, Università degli Studi di Milano, Via Balzaretti 9, 20133 Milano (Italy); Racchi, Marco [Dipartimento di Scienze del Farmaco, Università degli Studi di Pavia, Viale Taramelli 12/14, 27100 Pavia (Italy); Corsini, Emanuela, E-mail: emanuela.corsini@unimi.it [Laboratory of Toxicology, Dipartimento di Scienze Farmacologiche e Biomolecolari, Università degli Studi di Milano, Via Balzaretti 9, 20133 Milano (Italy)

2017-06-15

We recently demonstrated the existence of a complex hormonal balance between steroid hormones in the control of RACK1 (Receptor for Activated C Kinase 1) expression and immune activation, suggesting that this scaffold protein may also be targeted by endocrine disrupting chemicals (EDCs). As a proof of concept, we investigated the effect of the doping agent nandrolone, an androgen receptor (AR) agonist, and of p,p′DDT (dichlorodiphenyltrichloroethane) and its main metabolite p,p′DDE (dichlorodiphenyldichloroethylene), a weak and strong AR antagonist, respectively, on RACK1 expression and innate immune response. In analogy to endogenous androgens, nandrolone induced a dose-related increase in RACK1 transcriptional activity and protein expression, resulting in increased LPS-induced IL-8 and TNF-α production and proliferation in THP-1 cells. Conversely, p,p′DDT and p,p′DDE significantly decrease RACK1 expression, LPS-induced cytokine production and CD86 expression; with p,p′DDE exerting a stronger repressor effect than p,p′DDT, consistent with its stronger AR antagonistic effect. These results indicate that RACK1 could be a relevant target of EDCs, responding in opposite ways to agonist or antagonist of AR, representing a bridge between the endocrine system and the innate immune system. - Highlights: • RACK1 expression can be induced by AR agonists with a consequent enhancement of the response to LPS. • RACK1 can be negatively modulated by the AR antagonists DDT and its main metabolite p,p′DDE. • RACK1 can be a relevant target of EDCs, representing a bridge between the endocrine system and the immune system.

NASA/First Materials Science Research Rack (MSRR-1) Module Inserts Development for the International Space Station

Science.gov (United States)

Crouch, Myscha; Carswell, Bill; Farmer, Jeff; Rose, Fred; Tidwell, Paul

1999-01-01

The Material Science Research Rack 1 (MSRR-1) of the Material Science Research Facility (MSRF) contains an Experiment Module (EM) being developed collaboratively by NASA and the European Space Agency (ESA). This NASA/ESA EM will accommodate several different removable and replaceable Module Inserts (MIs) which are installed on orbit. Two of the NASA MIs being developed for specific material science investigations are described herein.

Status of the double Chooz experiment

Energy Technology Data Exchange (ETDEWEB)

Gonzalez, L.F.G.; Kemp, E. [Universidade Estadual de Campinas (IFGW/UNICAMP), SP (Brazil). Inst. de Fisica Gleb Wataghin. Dept. de Raios Cosmicos e Cronologia; Anjos, J.C. dos; Lima Junior, H.P.; Gama, R.; Abrahao, T.; Pepe, I.M. [Centro Brasileiro de Pesquisas Fisicas (MCT/CBPF), Rio de Janeiro, RJ (Brazil)

2012-07-01

Full text: The neutrino oscillation experiment Double Chooz, located at the nuclear power plant of Chooz (Ardennes, France), has as purpose to measure the mixing angle {theta}{sub 13} with greater precision than the measurement of its predecessor, the Chooz experiment. For this, the Double Chooz experiment will use antineutrinos generated in both Chooz plant reactors and will make high accuracy measurements of the flux in two different baselines with identical gadolinium-doped-scintillator detectors, that uses the inverse-beta-decay positron and neutron detection as an antineutrino signature. This signature is given by a prompt signal from the positron and a delayed neutron signal, which allow to decrease significantly the uncorrelated background. Other forms of background, in particular the cosmic correlated one, are managed using different technic. The use of two equal detectors at different baselines will allow to better control our systematic errors, in particular the ones associated with the reactor and with the reactor anomaly effect. The first detector (known as the 'far detector', 1050m from the reactors) is already in operation since April 2011 and the second one (known as the 'near detector', 400m from the reactor) is under construction. Thus, in this work we present the main aspects of this neutrino oscillation experiment and results update. (author)

Carbon Dioxide Dispersion in the Combustion Integrated Rack Simulated Numerically

Science.gov (United States)

Wu, Ming-Shin; Ruff, Gary A.

2004-01-01

When discharged into an International Space Station (ISS) payload rack, a carbon dioxide (CO2) portable fire extinguisher (PFE) must extinguish a fire by decreasing the oxygen in the rack by 50 percent within 60 sec. The length of time needed for this oxygen reduction throughout the rack and the length of time that the CO2 concentration remains high enough to prevent the fire from reigniting is important when determining the effectiveness of the response and postfire procedures. Furthermore, in the absence of gravity, the local flow velocity can make the difference between a fire that spreads rapidly and one that self-extinguishes after ignition. A numerical simulation of the discharge of CO2 from PFE into the Combustion Integrated Rack (CIR) in microgravity was performed to obtain the local velocity and CO2 concentration. The complicated flow field around the PFE nozzle exits was modeled by sources of equivalent mass and momentum flux at a location downstream of the nozzle. The time for the concentration of CO2 to reach a level that would extinguish a fire anywhere in the rack was determined using the Fire Dynamics Simulator (FDS), a computational fluid dynamics code developed by the National Institute of Standards and Technology specifically to evaluate the development of a fire and smoke transport. The simulation shows that CO2, as well as any smoke and combustion gases produced by a fire, would be discharged into the ISS cabin through the resource utility panel at the bottom of the rack. These simulations will be validated by comparing the results with velocity and CO2 concentration measurements obtained during the fire suppression system verification tests conducted on the CIR in March 2003. Once these numerical simulations are validated, portions of the ISS labs and living areas will be modeled to determine the local flow conditions before, during, and after a fire event. These simulations can yield specific information about how long it takes for smoke and

A background free double beta decay experiment

International Nuclear Information System (INIS)

Giomataris, I

2011-01-01

We present a new detection scheme for rejecting backgrounds in neutrino-less double beta decay experiments. It relies on the detection of Cherenkov light emitted by electrons in the MeV region. The momentum threshold is tuned to reach a good discrimination between background and good events. We consider many detector concepts and a range of target materials. The most promising is the high-pressure 136 Xe emitter where the required energy threshold is easily adjusted. Combination of this concept and a high pressure Time Projection Chamber could provide an optimal solution. A simple and low cost effective solution is the use of the Spherical Proportional Counter that provides, using a single read-out channel, two delayed signals from ionization and Cherenkov light. In solid-state double beta decay emitters, because of its higher density, the considered process is out of energy range. An escape will be the fabrication of double decay emitters having lower density by using for instance the aerogel technique. It is surprising that a technology used for particle identification in high-energy physics becomes a powerful tool for rejecting backgrounds in such low-energy experiments.

Double {Lambda}-hypernuclei at the PANDA experiment

Energy Technology Data Exchange (ETDEWEB)

Sanchez Lorente, Alicia, E-mail: a.sanchez@gsi.de [Helmholtz Institut Mainz (Germany); Collaboration: P-bar ANDA Collaboration

2012-12-15

Hypernuclear research will be one of the main topics addressed by the PANDA experiment at the planned Facility for Antiproton and Ion Research FAIR at Darmstadt (Germany). Thanks to the use of stored p-bar beams, copious production of double {Lambda} hypernuclei is expected at the PANDA experiment, which will enable high precision {gamma} spectroscopy of such nuclei for the first time. At PANDA excited states of {Xi}{sup }- hypernuclei will be used as a starting point for the formation of double {Lambda} hypernuclei. In order to predict the yield of particle stable double hypernuclei a microcanonical decay model was developed. For the detection of these nuclei, a devoted hypernuclear detector setup is planned. This set-up consists, in addition to the general purpose of the PANDA set-up, of a primary nuclear target for the production of {Xi}{sup -} + {Xi}-bar pairs, a secondary active target for the hypernuclei formation and the identification of associated decay products and a germanium array detector to perform {gamma} spectroscopy. Furthermore, the presence of {Xi}-bar can be used as an alternative to tag the strangeness in the {Xi}{sup -} + {Xi}-bar. All systems need to operate in the presence of a high magnetic field and a large hadronic background. In the present talk details concerning simulations, the identification procedure of double hypernuclei and the suppression of background will be presented. In addition, the present status of the detector developments for this programme will be briefly given.

Rack for nuclear fuel elements

International Nuclear Information System (INIS)

Rubinstein, H.J.; Gordon, C.B.; Robison, A.; Clark, P.M.

1977-01-01

Disclosed is a rack for storing spent nuclear fuel elements in which a plurality of aligned rows of upright enclosures of generally square cross-sectional areas contain vertically disposed spent fuel elements. Each fuel element is supported at the lower end thereof by a respective support that rests on the floor of the spent fuel pool for a nuclear power plant. An open rack frame is employed as an upright support for the enclosures containing the spent fuel elements. Legs at the lower corners of the frame rest on the floor of the pool to support the frame. In one exemplary embodiment, the support for the fuel element is in the form of a base on which a fuel element rests and the base is supported by legs. In another exemplary embodiment, each fuel element is supported on the pool floor by a self-adjusting support in the form of a base on which a fuel element rests and the base rests on a ball or swivel joint for self-alignment. The lower four corners of the frame are supported by legs adjustable in height for leveling the frame. Each adjustable frame leg is in the form of a base resting on the pool floor and the base supports a threaded post. The threaded post adjustably engages a threaded column on which rests the lower end of the frame. 16 claims, 14 figures

Double hypernuclei experiment with hybrid emulsion method at J-PARC

International Nuclear Information System (INIS)

Ekawa, Hiroyuki

2015-01-01

Double hypernuclei are important probes to study the system with strangeness S = -2. Several emulsion experiments had been performed to search for them. We are planning a new experiment to search for double hypernuclei at the K1.8 beam line in the Hadron Experimental Facility (J-PARC E07 experiment). Ξ"- tracks in the emulsion plates and SSD will be automatically connected by a hybrid method. The estimated Ξ"- stopped statistics is 10 times as high as that of the KEK E373 experiment. Discoveries of 10 new double hypernuclear species are expected, which enable us to discuss binding energy in terms of mass number dependence. On the other hand, we will also observe X rays from Ξ"- atoms with a germanium detector array installed close to the emulsion plates by tagging Ξ"- stopped events. This will be the first measurement to give information on the Ξ"- potential at the nuclear surface region. (author)

Three-dimensional microelectromechanical tilting platform operated by gear-driven racks

Science.gov (United States)

Klody, Kelly A.; Habbit, Jr., Robert D.

2005-11-01

A microelectromechanical (MEM) tiltable-platform apparatus is disclosed which utilizes a light-reflective platform (i.e. a micromirror) which is supported above a substrate by flexures which can be bent upwards to tilt the platform in any direction over an angle of generally .+-.10 degrees using a gear-driven rack attached to each flexure. Each rack is driven by a rotary microengine (i.e. a micromotor); and an optional thermal actuator can be used in combination with each microengine for initially an initial uplifting of the platform away from the substrate. The MEM apparatus has applications for optical switching (e.g. between a pair of optical fibers) or for optical beam scanning.

A novel regenerative shock absorber with a speed doubling mechanism and its Monte Carlo simulation

Science.gov (United States)

Zhang, Ran; Wang, Xu; Liu, Zhenwei

2018-03-01

A novel regenerative shock absorber has been designed and fabricated. The novelty of the presented work is the application of the double speed regenerative shock absorber that utilizes the rack and pinion mechanism to increase the magnet speed with respect to the coils for higher power output. The simulation models with parameters identified from finite element analysis and the experiments are developed. The proposed regenerative shock absorber is compared with the regenerative shock absorber without the rack and pinion mechanism, when they are integrated into the same quarter vehicle suspension system. The sinusoidal wave road profile displacement excitation and the random road profile displacement excitation with peak amplitude of 0.035 m are applied as the inputs in the frequency range of 0-25 Hz. It is found that with the sinusoidal and random road profile displacement input, the proposed innovative design can increase the output power by 4 times comparing to the baseline design. The proposed double speed regenerative shock absorber also presents to be more sensitive to the road profile irregularity than the single speed regenerative shock absorber as suggested by Monte Carlo simulation. Lastly the coil mass and amplification factor are studied for sensitivity analysis and performance optimization, which provides a general design method of the regenerative shock absorbers. It shows that for the system power output, the proposed design becomes more sensitive to either the coil mass or amplification factor depending on the amount of the coil mass. With the specifically selected combination of the coil mass and amplification factor, the optimized energy harvesting performance can be achieved.

The double chooz reactor neutrino experiment

Energy Technology Data Exchange (ETDEWEB)

Botella, I Gil [CIEMAT, Basic Research Department, Avenida Complutense, 22, 28040 Madrid (Spain)], E-mail: ines.gil@ciemat.es

2008-05-15

The Double Chooz reactor neutrino experiment will be the next detector to search for a non vanishing {theta}{sub 13} mixing angle with unprecedented sensitivity, which might open the way to unveiling CP violation in the leptonic sector. The measurement of this angle will be based in a precise comparison of the antineutrino spectrum at two identical detectors located at different distances from the Chooz nuclear reactor cores in France. Double Chooz is particularly attractive because of its capability to measure sin{sup 2} (2{theta}{sub 13}) to 3{sigma} if sin{sup 2}(2{theta}{sub 13}) > 0.05 or to exclude sin{sup 2}(2{theta}{sub 13}) down to 0.03 at 90% C.L. for {delta}m{sup 2} = 2.5 x 10{sup -3} eV{sup 2} in three years of data taking with both detectors. The construction of the far detector starts in 2008 and the first neutrino results are expected in 2009. The current status of the experiment, its physics potential and design and expected performance of the detector are reviewed.

Extra dimensions and neutrinoless double beta decay experiments

International Nuclear Information System (INIS)

Gozdz, Marek; Kaminski, Wieslaw A.; Faessler, Amand

2005-01-01

The neutrinoless double beta decay is one of the few phenomena, belonging to the nonstandard physics, which is extensively being sought for in experiments. In the present paper the link between the half-life of the neutrinoless double beta decay and theories with large extra dimensions is explored. The use of the sensitivities of currently planned 0ν2β experiments: DAMA, CANDLES, COBRA, DCBA, CAMEO, GENIUS, GEM, MAJORANA, MOON, CUORE, EXO, and XMASS, gives the possibility for a nondirect 'experimental' verification of various extra dimensional scenarios. We discuss also the results of the Heidelberg-Moscow Collaboration. The calculations are based on the Majorana neutrino mass generation mechanism in the Arkani-Hamed-Dimopoulos-Dvali model

Re-racking the spent fuel pit in nuclear power plant Krsko

International Nuclear Information System (INIS)

Volaric, B.; Krajnc, B.

2003-01-01

Krsko NPP was designed to temporary store a limited number of spent fuel assemblies (SFA). They were planned to be either removed for reprocessing or permanently stored. By the design the plant would run out of capacity for temporary storing of SFAs in 2003. This means that the plant could not operate further without additional changes since valid regulations require the Spent Fuel Pit (SFP) free storage capacity for the whole emergency core unloading (ECU). The purpose of the SFP Reracking Project is to assure a safe storage of all SFAs in the existing SFP during the plant lifetime. Design solutions and related analysis did not only consider the quantity of spent fuel for the plant lifetime, i.e. up to the year 2023, but also a possibility of the SFP extension for eventually extended plant lifetime of 20 years. According to the project, racks were designed to provide up to 1694 cells for storage of FAs in Phase I which is sufficient for normal NPP operation up to its lifetime, i.e. the year 2023. The extension of temporary storage capacity of SFAs in the SFP was made by a combination of existing and new high-density racks. Three modules from the existing 12 were eliminated. Thus leaving 621 cells. There are nine new racks added with up to 1073 supercompacted cells installed in the empty part of the pool. The spacing between new cells is smaller than the one between existing cells because of special plates, made of borated stainless steel. The design of the racks fulfils all the applicable requirements to ensure sub-criticality of all stored SFAs, enriched up to 5 % U 235 with peak pellet burnup above 40 GWD/MTU. Besides static and dynamic seismic loading of both, the racks and the fuel handling building, sufficient cooling of FAs is provided as well as accident conditions precluded. Greater cooling capacity is achieved by installing the third heat exchanger, connected in parallel to existing two exchangers. The design and manufacturing of the new heat exchanger

Source rack reload of the Tunisian gamma irradiation facility using Monte Carlo method

International Nuclear Information System (INIS)

Gharbi, Foued; Kadri, Omrane

2005-01-01

This work presents a Monte Carlo study of the cylindrical source rack geometry of the tunisian gamma irradiation facility, using Ge ant code of CERN. The study investigates the question of the reload of the source rack. studied configurations consist on housing four new pencils, two in the upper and two in the lower cylinder of the source rack. global dose rate uniformity inside a ''dummy's' product for the case of routine and non routine irradiation and as function of the product bulk density was calculated for eight hypothetical configurations. the same calculation was also performed for both of the original and the ideal, but not practical configuration. It was shown that hypothetical cases produced dose uniformity variations, according to product density, that were statistically no different than the original and the ideal configurations and that reload procedure can not improve the irradiation quality inside the tunisian facility

Sterile neutrino search with the Double Chooz experiment

Energy Technology Data Exchange (ETDEWEB)

Hellwig, Denise; Bekman, Ilja; Kampmann, Philipp; Schoppmann, Stefan; Soiron, Michael; Stahl, Achim; Wiebusch, Christopher [III. Physikalisches Institut B, RWTH Aachen (Germany)

2016-07-01

The Double Chooz experiment is a reactor neutrino disappearance experiment located at the Chooz nuclear power plant, France. It measures the electron-antineutrino flux of the two nuclear reactors with two detectors of identical design. A far detector at a distance of about 1 km is operating since 2011; a near detector at a distance of about 400 m is operating since the end of 2014. The combination of the two detectors offers sensitivity to sterile neutrino mixing parameters. Sterile neutrinos are neutrino mass states not taking part in weak interactions, but may mix with known neutrino states. This induces additional mixing angles and mass differences. This talk describes the search for sterile neutrinos and the sensitivity of Double Chooz to the mixing angle θ{sub 14}.

Influence of Rack Design and Disease Prevalence on Detection of Rodent Pathogens in Exhaust Debris Samples from Individually Ventilated Caging Systems.

Science.gov (United States)

Bauer, Beth A; Besch-Williford, Cynthia; Livingston, Robert S; Crim, Marcus J; Riley, Lela K; Myles, Matthew H

2016-11-01

Sampling of bedding debris within the exhaust systems of ventilated racks may be a mechanism for detecting murine pathogens in colony animals. This study examined the effectiveness of detecting pathogens by PCR analysis of exhaust debris samples collected from ventilated racks of 2 different rack designs, one with unfiltered air flow from within the cage to the air-exhaust pathway, and the other had a filter between the cage and the air-exhaust pathway. For 12 wk, racks were populated with either 1 or 5 cages of mice (3 mice per cage) infected with one of the following pathogens: mouse norovirus (MNV), mouse parvovirus (MPV), mouse hepatitis virus (MHV), Helicobacter spp., Pasteurella pneumotropica, pinworms, Entamoeba muris, Tritrichomonas muris, and fur mites. Pathogen shedding by infected mice was monitored throughout the study. In the filter-containing rack, PCR testing of exhaust plenums yielded negative results for all pathogens at all time points of the study. In the rack with open air flow, pathogens detected by PCR analysis of exhaust debris included MHV, Helicobacter spp., P. pneumotropica, pinworms, enteric protozoa, and fur mites; these pathogens were detected in racks housing either 1 or 5 cages of infected mice. Neither MPV nor MNV was detected in exhaust debris, even though prolonged viral shedding was confirmed. These results demonstrate that testing rack exhaust debris from racks with unfiltered air flow detected MHV, enteric bacteria and parasites, and fur mites. However, this method failed to reliably detect MNV or MPV infection of colony animals.

An Evaluation of Criticality Margin by an Application of Parallelogram Lattice Arrangement in the Nuclear Fuel Storage Rack

International Nuclear Information System (INIS)

Kim, Song Hyun; Kim, Hong Chul; Shin, Chang Ho; Kim, Jong Kyung; Kim, Kyo Youn

2010-01-01

The criticality evaluation in the nuclear fuel storage rack is essentially required for the prevention of the criticality accident. The square lattice structure of the storage rack is commonly used because it has a simple structure for the storage of the numerous fuel assemblies as well as the good mechanical strength. For the design of the fuel storage rack, the boron plate is commonly used for the criticality reduction. In this study, an arrangement method with the parallelogram lattice structure is proposed for the reduction of the boron concentration or the rack pitch. The criticality margins by the application of the parallelogram lattice were evaluated with MCNP5 code. From the result, the reduction of the boron concentrated in the borated-Al plate was evaluated

Review of the technical basis and verification of current analysis methods used to predict seismic response of spent fuel storage racks

International Nuclear Information System (INIS)

DeGrassi, G.

1992-10-01

This report presents the results of a literature review on spent fuel rack seismic analysis methods and modeling procedures. The analysis of the current generation of free standing high density spent fuel racks requires careful consideration of complex phenomena such as rigid body sliding and tilting motions; impacts between adjacent racks, between fuel assemblies and racks, and between racks and pool walls and floor; fluid coupling and frictional effects. The complexity of the potential seismic response of these systems raises questions regarding the levels of uncertainty and ranges of validity of the analytical results. BNL has undertaken a program to investigate and assess the strengths and weaknesses of current fuel rack seismic analysis methods. The first phase of this program involved a review of technical literature to identify the extent of experimental and analytical verification of the analysis methods and assumptions. Numerous papers describing analysis methods for free standing fuel racks were reviewed. However, the extent of experimental verification of these methods was found to be limited. Based on the information obtained from the literature review, the report provides an assessment of the significance of the issues of concern and makes recommendations for additional studies

Characterization of receptor of activated C kinase 1 (RACK1) and functional analysis during larval metamorphosis of the oyster Crassostrea angulata.

Science.gov (United States)

Yang, Bingye; Pu, Fei; Qin, Ji; You, Weiwei; Ke, Caihuan

2014-03-10

During a large-scale screen of the larval transcriptome library of the Portuguese oyster, Crassostrea angulata, the oyster gene RACK, which encodes a receptor of activated protein kinase C protein was isolated and characterized. The cDNA is 1,148 bp long and has a predicted open reading frame encoding 317 aa. The predicted protein shows high sequence identity to many RACK proteins of different organisms including molluscs, fish, amphibians and mammals, suggesting that it is conserved during evolution. The structural analysis of the Ca-RACK1 genomic sequence implies that the Ca-RACK1 gene has seven exons and six introns, extending approximately 6.5 kb in length. It is expressed ubiquitously in many oyster tissues as detected by RT-PCR analysis. The Ca-RACK1 mRNA expression pattern was markedly increased at larval metamorphosis; and was further increased along with Ca-RACK1 protein synthesis during epinephrine-induced metamorphosis. These results indicate that the Ca-RACK1 plays an important role in tissue differentiation and/or in cell growth during larval metamorphosis in the oyster, C. angulata. Copyright © 2013 Elsevier B.V. All rights reserved.

PandaX-III neutrinoless double beta decay experiment

Science.gov (United States)

Wang, Shaobo; PandaX-III Collaboration

2017-09-01

The PandaX-III experiment uses high pressure Time Projection Chambers (TPCs) to search for neutrinoless double-beta decay of Xe-136 with high energy resolution and sensitivity at the China Jin-Ping underground Laboratory II (CJPL-II). Fine-pitch Microbulk Micromegas will be used for charge amplification and readout in order to reconstruct both the energy and track of the neutrinoless double-beta decay event. In the first phase of the experiment, the detector, which contains 200 kg of 90% Xe-136 enriched gas operated at 10 bar, will be immersed in a large water tank to ensure 5 m of water shielding. For the second phase, a ton-scale experiment with multiple TPCs will be constructed to improve the detection probability and sensitivity. A 20-kg scale prototype TPC with 7 Micromegas modules has been built to optimize the design of Micromegas readout module, study the energy calibration of TPC and develop algorithm of 3D track reconstruction.

Retrocausation acting in the single-electron double-slit interference experiment

Science.gov (United States)

Hokkyo, Noboru

The single electron double-slit interference experiment is given a time-symmetric interpretation and visualization in terms of the intermediate amplitude of transition between the particle source and the detection point. It is seen that the retarded (causal) amplitude of the electron wave expanding from the source shows an advanced (retrocausal) bifurcation and merging in passing through the double-slit and converges towards the detection point as if guided by the advanced (retrocausal) wave from the detected electron. An experiment is proposed to confirm the causation-retrocausation symmetry of the electron behavior by observing the insensitivity of the interference pattern to non-magnetic obstacles placed in the shadows of the retarded and advanced waves appearing on the rear and front sides of the double-slit.

Double Beta Decay Experiments: Present Status and Prospects for the Future

Science.gov (United States)

Barabash, A. S.

The review of modern experiments on search and studying of double beta decay processes is done. Results of the most sensitive current experiments are discussed. The main attention is paid to EXO-200, KamLAND-Zen, GERDA-I and CUORE-0 experiments. Modern values of T1/2(2ν) and best present limits on neutrinoless double beta decay and double beta decay with Majoron emission are presented. Conservative limits on effective mass of a Majorana neutrino ( at the level of ˜ (0.01-0.1) eV are discussed. The main attention is paid to experiments of CUORE, GERDA, MAJORANA, EXO, KamLAND-Zen-2, SuperNEMO and SNO+. Possibilities of low-temperature scintillating bolometers on the basis of inorganic crystals (ZnSe, ZnMoO4, Li2MoO4, CaMoO4 and CdWO4) are considered too.

The double-slit experiment and the time-reversed fire alarm

International Nuclear Information System (INIS)

Halabi, T.

2010-01-01

When both slits of the double-slit experiment are open, closing one paradoxically increases the detection rate at some points on the detection screen. Feynman famously warned that temptation to understand such a puzzling feature only draws into blind alleys. Nevertheless, we gain insight into this feature by drawing an analogy between the double-slit experiment and a time-reversed fire alarm. Much as closing the slit increases probability of a future detection, ruling out fire drill scenarios, having heard the fire alarm, increases probability of a past fire (using Bayesian inference). Classically, Bayesian inference is associated with computing probabilities of past events. We therefore identify this feature of the double-slit experiment with a time-reversed thermodynamic arrow. We believe that much of the enigma of quantum mechanics is simply due to some variation of time's arrow. In further support of this, we employ a plausible formulation of the thermodynamic arrow to derive an uncertainty in classical mechanics that is reminiscent of quantum uncertainty.

Retrieval-travel-time model for free-fall-flow-rack automated storage and retrieval system

Science.gov (United States)

Metahri, Dhiyaeddine; Hachemi, Khalid

2018-03-01

Automated storage and retrieval systems (AS/RSs) are material handling systems that are frequently used in manufacturing and distribution centers. The modelling of the retrieval-travel time of an AS/RS (expected product delivery time) is practically important, because it allows us to evaluate and improve the system throughput. The free-fall-flow-rack AS/RS has emerged as a new technology for drug distribution. This system is a new variation of flow-rack AS/RS that uses an operator or a single machine for storage operations, and uses a combination between the free-fall movement and a transport conveyor for retrieval operations. The main contribution of this paper is to develop an analytical model of the expected retrieval-travel time for the free-fall flow-rack under a dedicated storage assignment policy. The proposed model, which is based on a continuous approach, is compared for accuracy, via simulation, with discrete model. The obtained results show that the maximum deviation between the continuous model and the simulation is less than 5%, which shows the accuracy of our model to estimate the retrieval time. The analytical model is useful to optimise the dimensions of the rack, assess the system throughput, and evaluate different storage policies.

Retort Racks for Polymeric Trays in 1400 Style Spray Retorts

National Research Council Canada - National Science Library

Bruins, Henderikus B

2003-01-01

The objective of this project was to design a retort rack that would maximize the retort capacity of a 1400 style spray retort and to select a material that would withstand the harsh retort spray environment...

Experiments on double beta decay

Energy Technology Data Exchange (ETDEWEB)

Busto, J [Neuchatel Univ. (Switzerland). Inst. de Physique

1996-11-01

The Double Beta Decay, and especially ({beta}{beta}){sub 0{nu}} mode, is an excellent test of Standard Model as well as of neutrino physics. From experimental point of view, a very large number of different techniques are or have been used increasing the sensitivity of this experiments quite a lot (the factor of 10{sup 4} in the last 20 years). In future, in spite of several difficulties, the sensitivity would be increased further, keeping the interest of this very important process. (author) 4 figs., 5 tabs., 21 refs.

NIF Double Shell outer/inner shell collision experiments

Science.gov (United States)

Merritt, E. C.; Loomis, E. N.; Wilson, D. C.; Cardenas, T.; Montgomery, D. S.; Daughton, W. S.; Dodd, E. S.; Desjardins, T.; Renner, D. B.; Palaniyappan, S.; Batha, S. H.; Khan, S. F.; Smalyuk, V.; Ping, Y.; Amendt, P.; Schoff, M.; Hoppe, M.

2017-10-01

Double shell capsules are a potential low convergence path to substantial alpha-heating and ignition on NIF, since they are predicted to ignite and burn at relatively low temperatures via volume ignition. Current LANL NIF double shell designs consist of a low-Z ablator, low-density foam cushion, and high-Z inner shell with liquid DT fill. Central to the Double Shell concept is kinetic energy transfer from the outer to inner shell via collision. The collision determines maximum energy available for compression and implosion shape of the fuel. We present results of a NIF shape-transfer study: two experiments comparing shape and trajectory of the outer and inner shells at post-collision times. An outer-shell-only target shot measured the no-impact shell conditions, while an `imaging' double shell shot measured shell conditions with impact. The `imaging' target uses a low-Z inner shell and is designed to perform in similar collision physics space to a high-Z double shell but can be radiographed at 16keV, near the viable 2DConA BL energy limit. Work conducted under the auspices of the U.S. DOE by LANL under contract DE-AC52-06NA25396.

On the equivalence between Young's double-slit and crystal double-refraction interference experiments.

Science.gov (United States)

Ossikovski, Razvigor; Arteaga, Oriol; Vizet, Jérémy; Garcia-Caurel, Enric

2017-08-01

We show, both analytically and experimentally, that under common experimental conditions the interference pattern produced in a classic Young's double-slit experiment is indistinguishable from that generated by means of a doubly refracting uniaxial crystal whose optic axis makes a skew angle with the light propagation direction. The equivalence between diffraction and crystal optics interference experiments, taken for granted by Arago and Fresnel in their pioneering research on the interference of polarized light beams, is thus rigorously proven.

Nuclear import of transcription factor BR-C is mediated by its interaction with RACK1.

Science.gov (United States)

Cheng, Daojun; Qian, Wenliang; Wang, Yonghu; Meng, Meng; Wei, Ling; Li, Zhiqing; Kang, Lixia; Peng, Jian; Xia, Qingyou

2014-01-01

The transcription factor Broad Complex (BR-C) is an early ecdysone response gene in insects and contains two types of domains: two zinc finger domains for the activation of gene transcription and a Bric-a-brac/Tramtrack/Broad complex (BTB) domain for protein-protein interaction. Although the mechanism of zinc finger-mediated gene transcription is well studied, the partners interacting with the BTB domain of BR-C has not been elucidated until now. Here, we performed a yeast two-hybrid screen using the BTB domain of silkworm BR-C as bait and identified the receptor for activated C-kinase 1 (RACK1), a scaffolding/anchoring protein, as the novel partner capable of interacting with BR-C. The interaction between BR-C and RACK1 was further confirmed by far-western blotting and pull-down assays. Importantly, the disruption of this interaction, via RNAi against the endogenous RACK1 gene or deletion of the BTB domain, abolished the nuclear import of BR-C in BmN4 cells. In addition, RNAi against the endogenous PKC gene as well as phosphorylation-deficient mutation of the predicted PKC phosphorylation sites at either Ser373 or Thr406 in BR-C phenocopied RACK1 RNAi and altered the nuclear localization of BR-C. However, when BTB domain was deleted, phosphorylation mimics of either Ser373 or Thr406 had no effect on the nuclear import of BR-C. Moreover, mutating the PKC phosphorylation sites at Ser373 and Thr406 or deleting the BTB domain significantly decreased the transcriptional activation of a BR-C target gene. Given that RACK1 is necessary for recruiting PKC to close and phosphorylate target proteins, we suggest that the PKC-mediated phosphorylation and nuclear import of BR-C is determined by its interaction with RACK1. This novel finding will be helpful for further deciphering the mechanism underlying the role of BR-C proteins during insect development.

Nuclear import of transcription factor BR-C is mediated by its interaction with RACK1.

Directory of Open Access Journals (Sweden)

Daojun Cheng

Full Text Available The transcription factor Broad Complex (BR-C is an early ecdysone response gene in insects and contains two types of domains: two zinc finger domains for the activation of gene transcription and a Bric-a-brac/Tramtrack/Broad complex (BTB domain for protein-protein interaction. Although the mechanism of zinc finger-mediated gene transcription is well studied, the partners interacting with the BTB domain of BR-C has not been elucidated until now. Here, we performed a yeast two-hybrid screen using the BTB domain of silkworm BR-C as bait and identified the receptor for activated C-kinase 1 (RACK1, a scaffolding/anchoring protein, as the novel partner capable of interacting with BR-C. The interaction between BR-C and RACK1 was further confirmed by far-western blotting and pull-down assays. Importantly, the disruption of this interaction, via RNAi against the endogenous RACK1 gene or deletion of the BTB domain, abolished the nuclear import of BR-C in BmN4 cells. In addition, RNAi against the endogenous PKC gene as well as phosphorylation-deficient mutation of the predicted PKC phosphorylation sites at either Ser373 or Thr406 in BR-C phenocopied RACK1 RNAi and altered the nuclear localization of BR-C. However, when BTB domain was deleted, phosphorylation mimics of either Ser373 or Thr406 had no effect on the nuclear import of BR-C. Moreover, mutating the PKC phosphorylation sites at Ser373 and Thr406 or deleting the BTB domain significantly decreased the transcriptional activation of a BR-C target gene. Given that RACK1 is necessary for recruiting PKC to close and phosphorylate target proteins, we suggest that the PKC-mediated phosphorylation and nuclear import of BR-C is determined by its interaction with RACK1. This novel finding will be helpful for further deciphering the mechanism underlying the role of BR-C proteins during insect development.

The Majorana Double Beta Decay Experiment:. Present Status

Science.gov (United States)

Aguayo, E.; Avignone, F. T.; Back, H. O.; Barabash, A. S.; Beene, J. R.; Bergevin, M.; Bertrand, F. E.; Boswell, M.; Brudanin, V.; Busch, M.; Chan, Y.-D.; Christofferson, C. D.; Collar, J. I.; Combs, D. C.; Cooper, R. J.; Detwiler, J. A.; Doe, P. J.; Efremenko, Yu.; Egorov, V.; Ejiri, H.; Elliott, S. R.; Esterline, J.; Fast, J. E.; Fields, N.; Finnerty, P.; Fraenkle, F. M.; Gehman, V. M.; Giovanetti, G. K.; Green, M. P.; Guiseppe, V. E.; Gusey, K.; Hallin, A. L.; Hazama, R.; Henning, R.; Hime, A.; Hoppe, E. W.; Horton, M.; Howard, S.; Howe, M. A.; Johnson, R. A.; Keeter, K. J.; Keller, C.; Kidd, M. F.; Knecht, A.; Kochetov, O.; Konovalov, S. I.; Kouzes, R. T.; Laferriere, B. D.; Laroque, B. H.; Leon, J.; Leviner, L. E.; Loach, J. C.; Macmullin, S.; Marino, M. G.; Martin, R. D.; Mei, D.-M.; Merriman, J. H.; Miller, M. L.; Mizouni, L.; Nomachi, M.; Orrell, J. L.; Overman, N. R.; Phillips, D. G.; Poon, A. W. P.; Perumpilly, G.; Prior, G.; Radford, D. C.; Rielage, K.; Robertson, R. G. H.; Ronquest, M. C.; Schubert, A. G.; Shima, T.; Shirchenko, M.; Snavely, K. J.; Steele, D.; Strain, J.; Thomas, K.; Timkin, V.; Tornow, W.; Vanyushin, I.; Varner, R. L.; Vetter, K.; Vorren, K.; Wilkerson, J. F.; Yakushev, E.; Young, A. R.; Yu, C.-H.; Yumatov, V. I.; Zhang, C.

2013-11-01

The Majorana collaboration is actively pursuing research and development aimed at a tonne-scale 76Ge neutrinoless double-beta decay (0νββ) experiment. The current, primary focus is the construction of the Majorana Demonstrator experiment, an R&D effort that will field approximately 40 kg of germanium detectors with mixed enrichment levels. This article provides a status update on the construction of the Demonstrator.

OsRACK1 Is Involved in Abscisic Acid- and H2O2-Mediated Signaling to Regulate Seed Germination in Rice (Oryza sativa, L.)

Science.gov (United States)

Zhang, Dongping; Chen, Li; Li, Dahong; Lv, Bing; Chen, Yun; Chen, Jingui; XuejiaoYan; Liang, Jiansheng

2014-01-01

The receptor for activated C kinase 1 (RACK1) is one member of the most important WD repeat–containing family of proteins found in all eukaryotes and is involved in multiple signaling pathways. However, compared with the progress in the area of mammalian RACK1, our understanding of the functions and molecular mechanisms of RACK1 in the regulation of plant growth and development is still in its infancy. In the present study, we investigated the roles of rice RACK1A gene (OsRACK1A) in controlling seed germination and its molecular mechanisms by generating a series of transgenic rice lines, of which OsRACK1A was either over-expressed or under-expressed. Our results showed that OsRACK1A positively regulated seed germination and negatively regulated the responses of seed germination to both exogenous ABA and H2O2. Inhibition of ABA biosynthesis had no enhancing effect on germination, whereas inhibition of ABA catabolism significantly suppressed germination. ABA inhibition on seed germination was almost fully recovered by exogenous H2O2 treatment. Quantitative analyses showed that endogenous ABA levels were significantly higher and H2O2 levels significantly lower in OsRACK1A-down regulated transgenic lines as compared with those in wildtype or OsRACK1A-up regulated lines. Quantitative real-time PCR analyses showed that the transcript levels of OsRbohs and amylase genes, RAmy1A and RAmy3D, were significantly lower in OsRACK1A-down regulated transgenic lines. It is concluded that OsRACK1A positively regulates seed germination by controlling endogenous levels of ABA and H2O2 and their interaction. PMID:24865690

Double nursing degree: potentialities and challenges of an international student academic experience.

Science.gov (United States)

Nora, Carlise Rigon Dalla; Schaefer, Rafaela; Schveitzer, Mariana Cabral; Zoboli, Elma Lourdes Campos Pavone; Vieira, Margarida Maria

2018-01-01

Objective To share the experience of a Double Nursing degree promoted between the Nursing School of the Universidade de São Paulo and the Health Sciences Institute of the Universidade Católica Portuguesa, reflecting on the potentialities and challenges of this opportunity for graduate students. Method This is an experience report presented in chronological order and of a descriptive nature. The double degree in Nursing was accomplished over a period of 6 months in a different institution from the institution of origin. Results Among the activities developed during the Double Degree are: participating in examining boards, congresses, seminars, courses, meetings, lectures, colloquium, classes, research groups and technical visits to health services. A table presents and describes the main benefits of the experience experienced by the authors. Conclusion When well-planned and well-developed, a double degree can promote personal, cultural and professional development of the students, favoring internationalization and contributing to the qualification of graduate programs.

77 FR 27029 - Certain Kitchen Shelving and Racks From the People's Republic of China: Extension of Time Limit...

Science.gov (United States)

2012-05-08

... DEPARTMENT OF COMMERCE International Trade Administration [C-570-942] Certain Kitchen Shelving and Racks From the People's Republic of China: Extension of Time Limit for Preliminary Results of... certain kitchen appliance shelving and racks from the People's Republic of China, covering the review...

Rollin' in Style!: Students Design Bike Mounted Skateboard Racks

Science.gov (United States)

Massey, Rick

2008-01-01

Recognizing the increasing popularity of skateboarding, the author has found a project that teaches design and manufacturing concepts--and, of equal importance, really gets his students motivated. He challenges them to design and build a skateboard rack that mounts easily on a bicycle. The project benefits students by teaching creativity, the…

Thermal analyses for the rack design with spent fuel pool during the loss of cooling accident

Energy Technology Data Exchange (ETDEWEB)

Yeh, C-L.; Chen, Y-S.; Chen, B-Y., E-mail: clinyeh@iner.gov.tw, E-mail: yschen@iner.gov.tw, E-mail: onepicemine@iner.gov.tw [Inst. of Nuclear Energy Research, Taoyuan County, Taiwan (China); Tseng, Y-S., E-mail: ystseng@mx.nthu.edu.tw [National Tsing Hua Univ., Engineering and System Science, Hsinchu, Taiwan (China); Wei, W-C., E-mail: hn150456@iner.gov.tw [Inst. of Nuclear Energy Research, Taoyuan County, Taiwan (China)

2014-07-01

Alternative fuel arrangements separating the latest fuels discharge from the reactor core are proposed, such as the 1x4 configuration in which the hot assembly is surrounded by 4 assemblies with much lower decay heat. For the rack design in the BWR spent fuel pool design, the lateral flow is eliminated by solid walls. In this study, cooling enhancement of splitting fuel rack is investigated using Computational Fluid Dynamics (CFD). The fuels in the pool are modeled by porous medium. Separating the fuel rack by a distance of 10 cm can lower the peak cladding temperature and the natural convection between the fuels and then earns more response time for the site people to implement necessary mitigation actions. (author)

Lessons Learned "Establishing an Electrically Safe Work Condition" Specifically related to Racking Electrical Breakers

Energy Technology Data Exchange (ETDEWEB)

Martinez, Tommy Robert [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Romero, Philbert Roland [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Garcia, Samuel Anthony [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2017-11-09

During low voltage electrical equipment maintenance, a bad breaker was identified. The breaker was racked out from the substation cubicle without following the hazardous energy control process identified in the Integrated Work Document (IWD). The IWD required the substation to be in an electrically safe work condition prior to racking the breaker. Per NFPA 70E requirements, electrical equipment shall be put into an electrically safe work condition before an employee performs work on or interacts with equipment in a manner that increases the likelihood of creating an arc flash. Racking in or out a breaker on an energized bus may increase the likelihood of creating an arc flash dependent on equipment conditions. A thorough risk assessment must be performed prior to performing such a task. The risk assessment determines the risk control measures to be put in place prior to performing the work. Electrical Safety Officers (ESO) can assist in performing risk assessments and incorporating risk control measures.

40 CFR Table 9 to Subpart Eeee of... - Continuous Compliance With Operating Limits-High Throughput Transfer Racks

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 12 2010-07-01 2010-07-01 true Continuous Compliance With Operating Limits-High Throughput Transfer Racks 9 Table 9 to Subpart EEEE of Part 63 Protection of Environment...—Continuous Compliance With Operating Limits—High Throughput Transfer Racks As stated in §§ 63.2378(a) and (b...

FSI-based Overflow Assessment of the Seismically-Isolated SFP with Fuel Racks

Energy Technology Data Exchange (ETDEWEB)

Chung, Gil Y.; Park, Hyun T.; Chang, Soo-Hyuk [Korea Maintenance Co., Seoul (Korea, Republic of); Lee, Sang-Hoon [KEPCO E-C, Yongin (Korea, Republic of)

2014-10-15

To date, effectiveness of the seismic isolation systems for reducing seismic force effectively has been well demonstrated. In this context, practical application of the technology in nuclear engineering fields has become an important issue more and more. This is because fluid motion can be rather amplified due to the increased relative displacement between the base and superstructures by a long-period shift. Therefore, overflow assessment and prediction of the seismically-isolated SFP have to be conducted in design phase. For performing sloshing-induced overflow of the seismically-isolated SFP, a fluid-structure interaction(FSI) approach making a two-way coupling process between structural and fluid solvers is herein employed. In this study, fuel racks inside the SFP are included in FSI modeling to investigate effect of fuel-cell assemblies on SFP overflow. Accordingly, three different assembly sets of fuel cells are assumed to be inserted in fuel racks. In addition, floor acceleration time-histories produced from three different amplitudes of peak ground acceleration (PGA) are applied to the SFP base to investigate load effect on liquid overflow. An approach for the liquid overflow assessment of the seismically-isolated nuclear SFP with fuel storage racks based on FSI analysis was addressed. From the results of the identified cases, the following conclusions are drawn: (i) FSI technique can be effectively used to assess the seismically-isolated SFP overflow, (ii) In a conservative way, the isolated SFP without fuel racks can be used to assess its sloshing-induced overflow under earthquake since effect of fuel-cell assemblies on the SFP overflow is not significant, (iii) for given same conditions (e.g., constant design free surface, same fuel-cell assembly) except seismic loading, the higher PGA is, the more liquid overflow increases.

To the question about the layout of the racks in the warehouse

Directory of Open Access Journals (Sweden)

Ilesaliev D.I.

2017-03-01

Full Text Available Warehouses, which are located at points of transshipment of cargo from one type of transport on the other, play a sig-nificant role in the transformation of cargo to further the most effective transportation of goods. The location of racks and longitudinal passages are important in the work of transhipment warehouse. Typically, racks and longitudinal pas-sages are perpendicular to each other, the article proposes a radical change with the "euclidean advantage". This is an-other way of designing warehouses for efficiency overload packaged cargo in the supply chain. Purpose is to reduce the mileage for one cycle of the loader from loading and unloading areas to storage areas.

Storage racks for spent nuclear fuels

International Nuclear Information System (INIS)

Matsumoto, Takashi; Ukaji, Hideo; Okino, Yoshiyuki; Ishihara, Jo; Ikuta, Isao.

1983-01-01

Purpose: To facilitate the mounting of neutron absorbers made of amorphous alloys to fuel racks. Constitution: Neutron absorbers are mounted to a cylindrical member of a square cross section for containing to retain spent fuels only on paired opposing sides by means of machine screws or the likes. Then, such cylindrical members are disposed so that their sides attached with the neutron absorbers are not in adjacent with each other. In this way, mounting of the neutron absorbers over the entire surface of the cylindrical members is no more necessary thereby enabling to simplify the mounting work. (Ikeda, J.)

Sterile Neutrino Search with the Double Chooz Experiment

Science.gov (United States)

Hellwig, D.; Matsubara, T.; Double Chooz Collaboration

2017-09-01

Double Chooz is a reactor antineutrino disappearance experiment located in Chooz, France. A far detector at a distance of about 1 km from reactor cores is operating since 2011; a near detector of identical design at a distance of about 400 m is operating since begin 2015. Beyond the precise measurement of θ 13, Double Chooz has a strong sensitivity to so called light sterile neutrinos. Sterile neutrinos are neutrino mass states not taking part in weak interactions, but may mix with known neutrino states. In this paper, we present an analysis method to search for sterile neutrinos and the expected sensitivity with the baselines of our detectors.

RACK1 forms a complex with FGFR1 and PKM2, and stimulates the growth and migration of squamous lung cancer cells.

Science.gov (United States)

Zhou, Chengzhi; Chen, Tao; Xie, Zhanhong; Qin, Yinyin; Ou, Yangming; Zhang, Jiexia; Li, Shiyue; Chen, Rongchang; Zhong, Nanshan

2017-11-01

Phosphorylation of Pyruvate Kinase M2 (PKM2) on Tyr105 by fibroblast growth factor receptor 1 (FGFR1) has been shown to promote its nuclear localization as well as cell growth in lung cancer. Better understanding the regulation of this process would benefit the clinical treatment for lung cancer. Here, it has been found that the adaptor protein receptor for activated PKC kinase (RACK1) formed a complex with FGFR1 and PKM2, and activated the FGFR1/PKM2 signaling. Knocking down the expression of RACK1 impaired the phosphorylation on Tyr105 of PKM2 and inhibited the growth and migration of lung cancer cells, while over-expression of RACK1 in lung cancer cells led to the resistance to Erdafitinib. Moreover, knocking down the expression of RACK1 impaired the tumorigenesis of lung cancer driven by LKB loss and mutated Ras (KrasG12D). Taken together, our study demonstrated the pivotal roles of RACK1 in FGFR1/PKM2 signaling, suggesting FGFR1/RACK1/PKM2 might be a therapeutic target for lung cancer treatment. © 2017 Wiley Periodicals, Inc.

Stability Analysis Of 3-d Conventional Pallet Rack Structures With Semi-rigid Connections

Directory of Open Access Journals (Sweden)

Kamal M. Bajoria

2009-12-01

Full Text Available This paper describe the three dimensional finite element modeling and buckling analysis of conventional pallet racking system with semi rigid connection. In this study three dimensional models of conventional pallet racking system were prepared using the finiteelement program ANSYS and finite element analysis carried out on conventional pallet racks with the 18 types of column sections developed along with semi-rigid connections. A parametric study was carried out to compare the effective length approach and the finiteelement method for accuracy and appropriateness for cold-formed steel frame design. Numerous frame elastic buckling analyses were carried out to evaluate the alignment chart and the AISI torsional-flexural buckling provisions. The parameters that influence the valueof Kx for column flexural buckling were examined in this study. The alignment chart and the AISI torsional-flexural buckling provisions, used to obtain the effective lengths and elastic buckling load of members were also evaluated. Results showed that the elastic buckling load obtained from the AISI torsional-flexural buckling provisions is generally conservative compared to the results obtained from performing frame elastic buckling analysis. Results also showed that, the effective length approach is more conservative than the finite element approach.

The Majorana Double Beta Decay Experiment: Present Status

Energy Technology Data Exchange (ETDEWEB)

Aguayo, Estanislao; Avignone, Frank T.; Back, Henning O.; Barabash, Alexander S.; Beene, Jim; Bergevin, M.; Bertrand, F.; Boswell, M.; Brudanin, V.; Busch, Matthew; Chan, Yuen-Dat; Christofferson, C. D.; Collar, J. I.; Combs, Dustin C.; Cooper, R. J.; Detwiler, Jason A.; Doe, Peter J.; Efremenko, Yuri; Egorov, Viatcheslav; Ejiri, H.; Elliott, S. R.; Esterline, James H.; Fast, James E.; Fields, N.; Finnerty, P.; Fraenkle, Florian; Gehman, Victor M.; Giovanetti, G. K.; Green, M. P.; Guiseppe, V. E.; Gusey, K.; Hallin, A. L.; Hazama, R.; Henning, Reyco; Hime, Andrew; Hoppe, Eric W.; Horton, Mark; Howard, Stanley; Howe, M. A.; Johnson, R. A.; Keeter, K.; Keller, C.; Kidd, M. F.; Knecht, A.; Kochetov, Oleg; Konovalov, S.; Kouzes, Richard T.; Laferriere, Brian D.; LaRoque, B. H.; Leon, Jonathan D.; Leviner, L.; Loach, J. C.; MacMullin, S.; Marino, Michael G.; Martin, R. D.; Mei, Dong-Ming; Merriman, Jason H.; Miller, M. L.; Mizouni, Leila; Nomachi, Masaharu; Orrell, John L.; Overman, Nicole R.; Phillips II, D. G.; Poon, Alan; Perumpilly, Gopakumar; Prior, Gersende; Radford, D. C.; Rielage, Keith; Robertson, R. G. H.; Ronquest, M. C.; Schubert, Alexis G.; Shima, T.; Shirchenko, M.; Snavely, Kyle J.; Steele, David; Strain, J.; Thomas, K.; Timkin, V.; Tornow, W.; Vanyushin, I.; Varner, R. L.; Vetter, Kai; Vorren, Kris R.; Wilkerson, J. F.; Yakushev, E.; Young, A.; Yu, Chang-Hong; Yumatov, Vladimir; Zhang, C.

2013-06-01

The Majorana collaboration is actively pursuing research and development aimed at a tonne-scale 76Ge neutrinoless double-beta decay experiment, an R&D effort that will field approximately 40 kg of germanium detectors with mixed enrichment levels. This article provides a status update on the construction of the Demonstrator

Shaping of Rack Cutter Original Profile for Fine-module Ratchet Teeth Cutting

Science.gov (United States)

Sharkov, O. V.; Koryagin, S. I.; Velikanov, N. L.

2018-05-01

The design models and the process of shaping the cutting edges of the rack cutter for cutting fine-module ratchet teeth are considered in the article. The use of fine-module ratchet teeth can reduce the noise and impact loads during operation of the freewheel mechanisms. Mathematical dependencies for calculating the coordinates determining the geometric position of the points of the front and back edges of the cutting profile of the rack cutter, the workpiece angle of rotation during cutting the ratchet teeth were obtained. When applying the developed method, the initial data are: the radii of the workpiece circumferences passing through the dedendum of the external and internal cut teeth; gradient angles of the front and back edges of the rail.

RACK1 downregulates levels of the pro-apoptotic protein Fem1b in apoptosis-resistant colon cancer cells.

Science.gov (United States)

Subauste, M Cecilia; Ventura-Holman, Tereza; Du, Liqin; Subauste, Jose S; Chan, Shing-Leng; Yu, Victor C; Maher, Joseph F

2009-12-01

Evasion of apoptosis plays an important role in colon cancer progression. Following loss of the Apc tumor suppressor gene in mice, the gene encoding Fem1b is upregulated early in neoplastic intestinal epithelium. Fem1b is a pro-apoptotic protein that interacts with Fas, TNFR1 and Apaf-1, and increased expression of Fem1b induces apoptosis of cancer cells. Fem1b is a homolog of FEM-1, a protein in Caenorhabditis elegans that is negatively regulated by ubiquitination and proteasomal degradation. To study Fem1b regulation in colon cancer progression, we used apoptotis-sensitive SW480 cells, derived from a primary colon cancer, and their isogenic, apoptosis-resistant counterparts SW620 cells, derived from a subsequent metastatic lesion in the same patient. Treatment with proteasome inhibitor increased Fem1b protein levels in SW620 cells, but not in SW480 cells. In SW620 cells we found that endogenous Fem1b co-immunoprecipitates in complexes with RACK1, a protein known to mediate ubiquitination and proteasomal degradation of other pro-apoptotic proteins and to be upregulated in colon cancer. Full-length Fem1b, or the N-terminal region of Fem1b, associated with RACK1 when co-expressed in HEK293T cells, and RACK1 stimulated ubiquitination of Fem1b. RACK1 overexpression in SW620 cells led to downregulation of Fem1b protein levels. Conversely, downregulation of RACK1 led to upregulation of Fem1b protein levels, associated with induction of apoptosis, and this apoptosis was inhibited by blocking Fem1b protein upregulation. In conclusion, RACK1 downregulates levels of the pro-apoptotic protein Fem1b in metastatic, apoptosis-resistant colon cancer cells, which may promote apoptosis-resistance during progression of colon cancer.

Can an off-the-rack orthotic stiletto alter pressure and comfort scores in the forefoot, arch and heel?

DEFF Research Database (Denmark)

Penny, Jeannette Østergaard; Speedtsberg, Merete Brink; Kallemose, Thomas

2018-01-01

MTH2+3 pressure (p rack orthotic stilettos can notably reduce...... plantar pressures and improve forefoot and heel comfort during everyday use. Practitioner Summary: Off-the-rack orthotic stilettos with built-in metatarsal pad, arch support and heel caps can lower the pressure under the heel and forefoot in comparison with a standard stiletto and can improve comfort...

Status of double beta decay experiments using isotopes other than 136Xe

Science.gov (United States)

Pandola, L.

2014-09-01

Neutrinoless double beta decay is a lepton-number violating process predicted by many extensions of the standard model. It is actively searched for in several candidate isotopes within many experimental projects. The status of the experimental initiatives which are looking for the neutrinoless double beta decay in isotopes other than 136Xe is reviewed, with special emphasis given to the projects that passed the R&D phase. The results recently released by the experiment GERDA are also summarized and discussed. The GERDA data give no positive indication of neutrinoless double beta decay of 76Ge and disfavor in a model-independent way the long-standing observation claim on the same isotope. The lower limit reported by GERDA for the half-life of neutrinoless double beta decay of 76Ge is T1/20ν > 2.1 ṡ1025 yr (90% C.L.), or T1/20ν > 3.0 ṡ1025 yr, when combined with the results of other 76Ge predecessor experiments.

Lessons Learned from the Crew Health Care System (CHeCS) Rack 1 Environmental Control and Life Support (ECLS) Design

Science.gov (United States)

Williams, David E.

2006-01-01

This paper will provide an overview of the International Space Station (ISS) Environmental Control and Life Support (ECLS) design of the Crew Health Care System (CHeCS) Rack 1 and it will document some of the lessons that have been learned to date for the ECLS equipment in this rack.

GERDA - a new neutrinoless double beta experiment using 76Ge

International Nuclear Information System (INIS)

Meierhofer, G

2011-01-01

The search for neutrinoless double beta decay (0νssss) has been a very active field for the last decades. While double beta decay has been observed, 0νssss decay still waits for its experimental proof. The GErmanium Detector Array (GERDA) uses 76 Ge, an ideal candidate as it is acting as source and detector simultaneously. Germanium detectors, isotopically enriched in 76 Ge are submerged directly into an ultra pure cryo liquid, which serves as coolant and radiation shield. This concept will allow to reduce the background by up to two orders of magnitude with respect to earlier experiments. GERDA has been constructed in hall A of the underground laboratory LNGS of the INFN in Italy. The experiment started recently with a test run.

First experiment with the double solenoid RIBRAS system

Energy Technology Data Exchange (ETDEWEB)

Lichtenthaeler, R.; Condori, R. Pampa; Lepine-Szily, A.; Pires, K. C. C.; Morais, M. C.; Leistenschneider, E.; Scarduelli, V. B.; Gasques, L. R. [Instituto de Fisica da USP, Sao Paulo, Brazil, C.P. 66318, 05314-970 (Brazil); Faria, P. N. de; Mendes, D. R. Jr. [Instituto de Fisica, Universidade Federal Fluminense, Niteroi, RJ, 24210-340 (Brazil); Shorto, J. M. B. [Instituto de Pesquisas Energeticas e Nucleares, IPEN/CNEN, Av. Lineu Prestes, 2242, 05508-000, Sao Paulo, SP (Brazil); Assuncao, M. [Departamento de Ciencias Exatas e da Terra, Universidade Federal de Sao Paulo, Campus Diadema, Sao Paulo (Brazil)

2013-05-06

A description of the double solenoid system (RIBRAS) operating since 2004 in one of the beam lines of the Pelletron Laboratory of the Institute of Physics of the University of Sao Paulo is presented. The recent installation of the secondary scattering chamber after the second solenoid is reported and the first experiment in RIBRAS using both solenoids is described.

Performance evaluation of METAMIC neutron absorber in spent fuel storage rack

Directory of Open Access Journals (Sweden)

Kiyoung Kim

2018-06-01

Full Text Available High-density spent fuel (SF storage racks have been installed to increase SF pool capacity. In these SF racks, neutron absorber materials were placed between fuel assemblies allowing the storage of fuel assemblies in close proximity to one another. The purpose of the neutron absorber materials is to preclude neutronic coupling between adjacent fuel assemblies and to maintain the fuel in a subcritical storage condition. METAMIC neutron absorber has been used in high-density storage racks. But, neutron absorber materials can be subject to severe conditions including long-term exposure to gamma radiation and neutron radiation. Recently, some of them have experienced degradation, such as white spots on the surface. Under these conditions, the material must continue to serve its intended function of absorbing neutrons. For the first time in Korea, this article uses a neutron attenuation test to examine the performance of METAMIC surveillance coupons. Also, scanning electron microscope analysis was carried out to verify the white spots that were detected on the surface of METAMIC. In the neutron attenuation test, there was no significant sign of boron loss in most of the METAMIC coupons, but the coupon with white spots had relatively less B-10 content than the others. In the scanning electron microscope analysis, corrosion material was detected in all METAMIC coupons. Especially, it was confirmed that the coupon with white spots contains much more corrosion material than the others. Keywords: Blister, Criticality, METAMIC, Neutron Absorber, Neutron Attenuation Test, Scanning Electron Microscope

Interference experiment with asymmetric double slit by using 1.2-MV field emission transmission electron microscope.

Science.gov (United States)

Harada, Ken; Akashi, Tetsuya; Niitsu, Kodai; Shimada, Keiko; Ono, Yoshimasa A; Shindo, Daisuke; Shinada, Hiroyuki; Mori, Shigeo

2018-01-17

Advanced electron microscopy technologies have made it possible to perform precise double-slit interference experiments. We used a 1.2-MV field emission electron microscope providing coherent electron waves and a direct detection camera system enabling single-electron detections at a sub-second exposure time. We developed a method to perform the interference experiment by using an asymmetric double-slit fabricated by a focused ion beam instrument and by operating the microscope under a "pre-Fraunhofer" condition, different from the Fraunhofer condition of conventional double-slit experiments. Here, pre-Fraunhofer condition means that each single-slit observation was performed under the Fraunhofer condition, while the double-slit observations were performed under the Fresnel condition. The interference experiments with each single slit and with the asymmetric double slit were carried out under two different electron dose conditions: high-dose for calculation of electron probability distribution and low-dose for each single electron distribution. Finally, we exemplified the distribution of single electrons by color-coding according to the above three types of experiments as a composite image.

HOTLink rack monitor

International Nuclear Information System (INIS)

Al R Franck et al.

2001-01-01

A remote data acquisition chassis, called a HOTLink Rack Monitor, HRM, has been developed for use in the Fermilab control system. This chassis provides for 64 analog input channels, 8 analog output channels, and 8 bytes of digital I/O. The interface to the host VMEbus crate is by way of a 320 MHz HOTLink serial connection to a PMC mezzanine module. With no processor intervention, all data sources in the remote chassis are read at 100 sec intervals, time stamped, and stored in a 2 MB circular buffer on the PMC module. In operation, the memory always contains the most recent 16 k samples of 10 kHz data from all 64 analog input channels. An expansion module that resides in the HRM chassis records snapshot data for 8 analog channels, each channel consisting of up to 16 k readings, digitized at rates up to 10 MHz. Snapshot data is also returned and stored in buffers on the PMC module. Because the HRM presents a memory-mapped interface to the host, it is independent of the operating system and may be used in any system that supports PMC mezzanine modules

Chasing theta-13 with the Double Chooz experiment

Energy Technology Data Exchange (ETDEWEB)

Lasserre, Thierry [CEA/DSM/IRFU/SPP, Gif-sur-Yvette (France)

2009-07-01

Neutrino oscillation physics is entering a precision measurement area. The smallness of the theta-13 neutrino mixing angle is still enigmatic and should be resolved. Double Chooz will use two identical detectors near the Chooz nuclear power station to search for a non vanishing theta-13, and hopefully open the way to experiments aspiring to discover CP violation in the leptonic sector.

Method and apparatus for storing nuclear fuel assemblies in maximum density racks

International Nuclear Information System (INIS)

Wachter, W.J.; Robbins, T.R.

1979-01-01

A maximum density storage rack is provided for long term or semipermanent storage of spent nuclear fuel assemblies. The rack consists of storage cells arranged in a regular array, such as a checkerboard, and intended to be immersed in water. Initially, cap members are placed on alternate cells in such a manner that at least 50% of the cells are left open, some of the caps being removable. Spent fuel assemblies are then placed in the open cells until all of them are filled. The level of reactivity of each of the stored fuel assemblies is then determined by accurate calculation or by measurement, and the removable caps are removed and rearranged so that other cells are opened, permitting the storage of additional fuel assemblies in a pattern based on the actual reactivity such that criticality is prevented

Experimental study on hydraulic characteristic around trash rack of a pumping station

Science.gov (United States)

Zhou, MinZhe; Li, TongChun; Lin, XiangYang; Liu, XiaoQing; Ding, Yuan; Liu, GuangYuan

2017-11-01

This paper focuses on flow pattern around trash rack of intake of a pumping station project. This pumping station undertake the task of supplying up to 3,500,000 m3 water per day for a megacity. Considering the large flow rate, high lift, multi-pipe supply and long-time operation in this water conveyance pumping station, we built a physical model test to measure the flow velocity and observe the flow pattern to verify the reasonability of preliminary design. In this test, we set 3 layers of current meters around each trash rack of intake in reservoir to collect the flow velocity. Furthermore, we design 2 operating conditions of 9 pumps to observe the change of flow pattern. Finally, we found the velocity data were in a normal range under 2 different operating conditions of the 9 pump units.

Storage rack for nuclear fuel assemblies

International Nuclear Information System (INIS)

Wachter, W.J.

1988-01-01

A storage rack for nuclear fuel assemblies is described comprising storage tubes, each having a polygon cross-section. The tubes being nested with cell walls of one tube aligned with and confronting cell walls of other tubes. Each cell wall having an array of embossed buttons so arranged that buttons of one cell wall engage buttons of a confronting cell wall, and the engage buttons are welded together to secure the tubes. At least one layer of neutron-poison material comprises a flexible, resilient pad interprosed between the aligned cell walls; whereby a major portion of the total outer surface area of each confronting cell wall is engaged with the layer of neutron-poison material

Design, Fabrication, and Testing of a Composite Rack Prototype in Support of the Deep Space Habitat Program

Science.gov (United States)

Smith, Russ; Hagen, Richard

2015-01-01

In support of the Deep Space Habitat project a number of composite rack prototypes were developed, designed, fabricated and tested to various extents ( with the International Standard Payload Rack configuration, or crew quarters, as a baseline). This paper focuses specifically on a composite rack prototype with a direct tie in to Space Station hardware. The outlined prototype is an all composite construction, excluding metallic fasteners, washers, and their associated inserts. The rack utilizes braided carbon composite tubing for the frame with the sidewalls, backwall and flooring sections utilizing aircraft grade composite honeycomb sandwich panels. Novel additively manufactured thermoplastic joints and tube inserts were also developed in support of this effort. Joint and tube insert screening tests were conducted at a preliminary level. The screening tests allowed for modification, and enhancement, of the fabrication and design approaches, which will be outlined. The initial joint tests did not include mechanical fasteners. Adhesives were utilized at the joint to composite tube interfaces, along with mechanical fasteners during final fabrication (thus creating a stronger joint than the adhesive only variant). In general the prototype was focused on a potential in-space assembly approach, or kit-of-parts construction concept, which would not necessarily require the inclusion of an adhesive in the joint regions. However, given the tie in to legacy Station hardware (and potential flight loads with imbedded hardware mass loadings), the rack was built as stiff and strong as possible. Preliminary torque down tests were also conducted to determine the feasibility of mounting the composite honeycomb panels to the composite tubing sections via the additively manufactured tube inserts. Additional fastener torque down tests were also conducted with inserts (helicoils) imbedded within the joints. Lessons learned are also included and discussed.

40 CFR 63.11088 - What requirements must I meet for gasoline loading racks if my facility is a bulk gasoline...

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 14 2010-07-01 2010-07-01 false What requirements must I meet for gasoline loading racks if my facility is a bulk gasoline terminal, pipeline breakout station, or pipeline... § 63.11088 What requirements must I meet for gasoline loading racks if my facility is a bulk gasoline...

Water-Cooled Data Center Packs More Power Per Rack | Poster

Science.gov (United States)

By Frank Blanchard and Ken Michaels, Staff Writers Behind each tall, black computer rack in the data center at the Advanced Technology Research Facility (ATRF) is something both strangely familiar and oddly out of place: It looks like a radiator. The back door of each cabinet is gridded with the coils of the Liebert cooling system, which circulates chilled water to remove heat

Nuclear fuel rack lateral support and preload device

International Nuclear Information System (INIS)

Knight, C.B.

1979-01-01

A lateral support device for a nuclear fuel rack is described. It is vertically positioned within a walled enclosure which provides a preload to maintain effective support. The device includes a scissors-jack which is mounted so that the drive screw is vertical. Upon rotation of the drive screw the jack expands horizontally, seating a load pad against a vertical wall. The load pad is affixed to the jack by an arm having a stack of spring washers which compress between the pad and the jack, thereby applying a selected preload

The GERDA Neutrinoless Double Beta-Decay Experiment

International Nuclear Information System (INIS)

Majorovits, Bela A.

2007-01-01

Neutrinoless double beta (0νββ)-decay is the key process to gain understanding of the nature of neutrinos. The GErmanium Detector Array (GERDA) is designed to search for 0νββ-decay of the isotope 76 Ge. Germanium crystals enriched in 76 Ge, acting as source and detector simultaneously, will be submerged directly into an ultra pure cooling medium that also serves as a radiation shield. This concept will allow for a reduction of the background by up to two orders of magnitudes with respect to earlier experiments

Latest results from the Double Chooz experiment

Energy Technology Data Exchange (ETDEWEB)

Goeger-Neff, Marianne [Physik Department E15, Technische Universitaet Muenchen (Germany); Collaboration: Double Chooz-Collaboration

2016-07-01

Double Chooz aims at a precise measurement of the neutrino mixing angle θ{sub 13} through the disappearance of reactor electron antineutrinos. The experiment relies on the measurement of neutrino flux and spectrum with two identical detectors at 400 m and 1000 m from the reactor cores of two nuclear power reactors. anti ν{sub e} are detected by inverse beta decay on free protons in 8.3 tons of Gd-loaded liquid scintillator, providing a unique delayed coincidence signature. Double Chooz has been running since 2011 with the far detector only, providing the first indication for non-zero θ{sub 13} with reactor antineutrinos. With a rate+shape analysis of 467.90 live days from 2011-2013 we obtain a value of sin {sup 2} 2 θ{sub 13}=0.090{sup +0.032}{sub -0.029}. Data taking with the near detector has started beginning of 2015, allowing a significant reduction of both reactor and detector related systematic uncertainties. The talk reviews the most recent results obtained with the far detector only and discuss first data from the near detector.

AN INTERNET RACK MONITOR-CONTROLLER FOR APS LINAC RF ELECTRONICS UPGRADE

Energy Technology Data Exchange (ETDEWEB)

Ma, Hengjie; Smith, Terry; Nassiri, Alireza; Sun, Yine; Doolittle, Lawrence; Ratti, Alex

2016-06-01

To support the research and development in APS LINAC area, the existing LINAC rf control performance needs to be much improved, and thus an upgrade of the legacy LINAC rf electronics becomes necessary. The proposed upgrade plan centers on the concept of using a modern, network-attached, rackmount digital electronics platform –Internet Rack Monitor-Controller (or IRMC) to achieve the goal of modernizing the rf electronics at a lower cost. The system model of the envisioned IRMC is basically a 3-tier stack with a high-performance DSP in the mid-layer to perform the core tasks of real-time rf data processing and controls. The Digital Front-End (DFE) attachment layer at bottom bridges the applicationspecific rf front-ends to the DSP. A network communication gateway, together with an embedded event receiver (EVR) in the top layer merges the Internet Rack MonitorController node into the networks of the accelerator controls infrastructure. Although the concept is very much in trend with today’s Internet-of-Things (IoT), this implementation has actually been used in the accelerators for over two decades.

Graphical explanation in an expert system for Space Station Freedom rack integration

Science.gov (United States)

Craig, F. G.; Cutts, D. E.; Fennel, T. R.; Purves, B.

1990-01-01

The rationale and methodology used to incorporate graphics into explanations provided by an expert system for Space Station Freedom rack integration is examined. The rack integration task is typical of a class of constraint satisfaction problems for large programs where expertise from several areas is required. Graphically oriented approaches are used to explain the conclusions made by the system, the knowledge base content, and even at more abstract levels the control strategies employed by the system. The implemented architecture combines hypermedia and inference engine capabilities. The advantages of this architecture include: closer integration of user interface, explanation system, and knowledge base; the ability to embed links to deeper knowledge underlying the compiled knowledge used in the knowledge base; and allowing for more direct control of explanation depth and duration by the user. The graphical techniques employed range from simple statis presentation of schematics to dynamic creation of a series of pictures presented motion picture style. User models control the type, amount, and order of information presented.

Serious complications in experiments in which UV doses are effected by using different lamp heights.

Science.gov (United States)

Flint, Stephan D; Ryel, Ronald J; Hudelson, Timothy J; Caldwell, Martyn M

2009-10-06

Many experiments examining plant responses to enhanced ultraviolet-B radiation (280-315nm) simply compare an enhanced UV-B treatment with ambient UV-B (or no UV-B radiation in most greenhouse and controlled-environment studies). Some more detailed experiments utilize multiple levels of UV-B radiation. A number of different techniques have been used to adjust the UV dose. One common technique is to place racks of fluorescent UV-emitting lamps at different heights above the plant canopy. However, the lamps and associated support structure cast shadows on the plant bed below. We calculated one example of the sequence of shade intervals for two common heights of lamp racks and show the patterns and duration of shade which the plants receive is distributed differently over the course of the day for different heights of the lamp racks. We also conducted a greenhouse experiment with plants (canola, sunflower and maize) grown under unenergized lamp racks suspended at the same two heights above the canopy. Growth characteristics differed in unpredictable ways between plants grown under the two heights of lamp racks. These differences could enhance or obscure potential UV-B effects. Also, differences in leaf mass per unit foliage area, which were observed in this experiment, could contribute to differences in plant UV-B sensitivity. We recommend the use of other techniques for achieving multiple doses of UV-B radiation. These range from simple and inexpensive approaches (e.g., wrapping individual fluorescent tubes in layers of a neutral-density filter such as cheese cloth) to more technical and expensive alternatives (e.g., electronically modulated lamp control systems). These choices should be determined according to the goals of the particular experiment.

Lactobacillus casei triggers a TLR mediated RACK-1 dependent p38 MAPK pathway in Caenorhabditis elegans to resist Klebsiella pneumoniae infection.

Science.gov (United States)

Kamaladevi, Arumugam; Balamurugan, Krishnaswamy

2016-07-13

In the present study, the effect of Lactic Acid Bacteria (LAB) was investigated at the molecular level using the model organism Caenorhabditis elegans against Klebsiella pneumoniae. Out of the 13 LAB screened, Lactobacillus casei displayed excellent protective efficacy by prolonging the survival of K. pneumoniae-infected nematodes. Pretreatment with L. casei significantly decreased bacterial colonization and rescued K. pneumoniae-infected C. elegans from various physiological impairments. The concomitant upregulation of key immune genes that regulate the TLR, RACK-1 as well as the p38 MAPK pathway rather than the IIS and ERK pathway suggested that the plausible immunomodulatory mechanism of L. casei could be by triggering the TLR, RACK-1 and p38 MAPK pathway. Furthermore, the hyper-susceptibility of L. casei treated loss-of-function mutants of the tol-1, RACK-1 and p38 MAPK pathway (sek-1 and pmk-1) to K. pneumoniae infection and gene expression analysis suggested that L. casei triggered a TLR mediated RACK-1 dependent p38 MAPK pathway to increase host resistance and protect nematodes against K. pneumoniae infection.

Finally making sense of the double-slit experiment.

Science.gov (United States)

Aharonov, Yakir; Cohen, Eliahu; Colombo, Fabrizio; Landsberger, Tomer; Sabadini, Irene; Struppa, Daniele C; Tollaksen, Jeff

2017-06-20

Feynman stated that the double-slit experiment "…has in it the heart of quantum mechanics. In reality, it contains the only mystery" and that "nobody can give you a deeper explanation of this phenomenon than I have given; that is, a description of it" [Feynman R, Leighton R, Sands M (1965) The Feynman Lectures on Physics ]. We rise to the challenge with an alternative to the wave function-centered interpretations: instead of a quantum wave passing through both slits, we have a localized particle with nonlocal interactions with the other slit. Key to this explanation is dynamical nonlocality, which naturally appears in the Heisenberg picture as nonlocal equations of motion. This insight led us to develop an approach to quantum mechanics which relies on pre- and postselection, weak measurements, deterministic, and modular variables. We consider those properties of a single particle that are deterministic to be primal. The Heisenberg picture allows us to specify the most complete enumeration of such deterministic properties in contrast to the Schrödinger wave function, which remains an ensemble property. We exercise this approach by analyzing a version of the double-slit experiment augmented with postselection, showing that only it and not the wave function approach can be accommodated within a time-symmetric interpretation, where interference appears even when the particle is localized. Although the Heisenberg and Schrödinger pictures are equivalent formulations, nevertheless, the framework presented here has led to insights, intuitions, and experiments that were missed from the old perspective.

Improvement of rotary specimen rack design

International Nuclear Information System (INIS)

Batch, J.M.; Gietzen, A.J.

1978-01-01

A redesign and verification test program has been completed on a new Rotary Specimen Rack ('Lazy Susan') design for the TRIGA Mark III. The purpose of the redesign was to solve a rotation problem which occurred at power levels of about 1 MW and above. The previous redesign effort on the Mark II-type lazy susan was made in 1967 when the bearing was changed to use stellite balls, spring-type separators and stainless-steel bearing races. An extensive test program at that time showed that the design gave excellent service under all anticipated operating conditions. Fifteen of these units have been installed in the past ten years and have been essentially trouble-free. Although the bearing design for the Mark III was very similar, the component layout was such that irradiation-induced heating with associated thermal expansion resulted in decreased bearing clearance and an increase in the required driving torque. The solution involved redesign and re-arrangement of the rack drive mechanism. A series of stringent operational proof tests were made under high temperature and temperature differential conditions which proved successful operation of the new design. The severe conditions under which these tests were performed uncovered further difficulties with the bearing and led to a re-evaluation of the bearing design. A new design was developed in which the spring separators were replaced by similar sized, cylindrical graphite spacers. The entire series of operational and life tests were repeated and the performance was outstanding. Acceptable wear characteristics of the spacers were verified and the bearing was noticeably smoother and quieter than with previous designs. A Mark III lazy susan of this new design was installed in a TRIGA about one year ago and operated at power levels up to 2 MW with excellent performance. The Mark II design has now been changed to incorporate the new drive and bearing design proven for the Mark III. (author)

Metal-driven and covalent synthesis of supramolecular grids from racks: a convergent approach to heterometallic and heteroleptic nanostructures.

Science.gov (United States)

Schmittel, Michael; Kalsani, Venkateshwarlu; Bats, Jan W

2005-06-13

Supramolecular nanogrids were prepared from dynamic supramolecular racks through the coupling of terminal alkynes using either a covalent (with CuCl/O(2)) or a coordinative (with [trans-(PEt(3))(2)PtCl(2)]) approach. Because of the rapid equilibration of the racks (as tested by exchange reactions), oligomeric adducts potentially formed in the coupling process will selectively furnish the nanogrids through an entropically driven self-repair mechanism. To ascertain the structural assignment, the nanogrids were also synthesized by an independent strategy.

Gerda: A new 76Ge Double Beta Decay Experiment at Gran Sasso

International Nuclear Information System (INIS)

Simgen, Hardy

2005-01-01

In the new 76 Ge double beta decay experiment Gerda [I. Abt et al., arXiv hep-ex/0404039; Gerda proposal, to be submitted to the Gran Sasso scientific committee] bare diodes of enriched 76 Ge will be operated in highly pure liquid nitrogen or argon. The goal is to reduce the background around Q ββ =2039 keV below 10 -3 counts/(kg-bar keV-bar y). With presently available diodes from the Igex and HdMs experiments the current evidence for neutrinoless double beta decay [H.-V. Klapdor-Kleingrothaus, et al., Mod. Phys. Lett. A16 (2001) 2409ff] can unambigously be checked within one year of measurement

Measurement of the neutrino mixing angle θ13 with the Double Chooz experiment

Science.gov (United States)

Ostrovskiy, Igor

2009-10-01

The neutrino mixing angle θ13 is last one which value is still unknown. Measuring the θ13 is important for completing our understanding of three flavor neutrino oscillations. Moreover, leptonic CP violation could only be measured in case the value of θ13 is not zero. The current best limit (^2(2θ13)Ardennes. Described in this talk, is another experiment, Double Chooz, that is being prepared at the same site. The Double Chooz experiment offers several fundamental improvements and is aiming to surpass the current limit by an order of magnitude (^2(2θ13) < 0.03). Details of the detector design, overview of systematic errors and expected sensitivity, as well as current status of the experiment are presented.

Plasmonic rack-and-pinion gear with chiral metasurface

Science.gov (United States)

Gorodetski, Yuri; Karabchevsky, Alina

2016-04-01

The effect of circularly polarized beaming excited by traveling surface plasmons, via chiral metasurface is experimentally studied. Here we show that the propagation direction of the plasmonic wave, evanescently excited on the thin gold film affects the handedness of the scattered beam polarization. Nanostructured metasurface leads to excitation of localized plasmonic modes whose relative spatial orientation induces overall spin-orbit interaction. This effect is analogical to the rack-and-pinion gear: the rotational motion into the linear motion converter. From the practical point of view, the observed effect can be utilized in integrated optical circuits for communication systems, cyber security and sensing.

Double-slit experiment with single wave-driven particles and its relation to quantum mechanics.

Science.gov (United States)

Andersen, Anders; Madsen, Jacob; Reichelt, Christian; Rosenlund Ahl, Sonja; Lautrup, Benny; Ellegaard, Clive; Levinsen, Mogens T; Bohr, Tomas

2015-07-01

In a thought-provoking paper, Couder and Fort [Phys. Rev. Lett. 97, 154101 (2006)] describe a version of the famous double-slit experiment performed with droplets bouncing on a vertically vibrated fluid surface. In the experiment, an interference pattern in the single-particle statistics is found even though it is possible to determine unambiguously which slit the walking droplet passes. Here we argue, however, that the single-particle statistics in such an experiment will be fundamentally different from the single-particle statistics of quantum mechanics. Quantum mechanical interference takes place between different classical paths with precise amplitude and phase relations. In the double-slit experiment with walking droplets, these relations are lost since one of the paths is singled out by the droplet. To support our conclusions, we have carried out our own double-slit experiment, and our results, in particular the long and variable slit passage times of the droplets, cast strong doubt on the feasibility of the interference claimed by Couder and Fort. To understand theoretically the limitations of wave-driven particle systems as analogs to quantum mechanics, we introduce a Schrödinger equation with a source term originating from a localized particle that generates a wave while being simultaneously guided by it. We show that the ensuing particle-wave dynamics can capture some characteristics of quantum mechanics such as orbital quantization. However, the particle-wave dynamics can not reproduce quantum mechanics in general, and we show that the single-particle statistics for our model in a double-slit experiment with an additional splitter plate differs qualitatively from that of quantum mechanics.

Double-slit experiment with single wave-driven particles and its relation to quantum mechanics

Science.gov (United States)

Andersen, Anders; Madsen, Jacob; Reichelt, Christian; Rosenlund Ahl, Sonja; Lautrup, Benny; Ellegaard, Clive; Levinsen, Mogens T.; Bohr, Tomas

2015-07-01

In a thought-provoking paper, Couder and Fort [Phys. Rev. Lett. 97, 154101 (2006), 10.1103/PhysRevLett.97.154101] describe a version of the famous double-slit experiment performed with droplets bouncing on a vertically vibrated fluid surface. In the experiment, an interference pattern in the single-particle statistics is found even though it is possible to determine unambiguously which slit the walking droplet passes. Here we argue, however, that the single-particle statistics in such an experiment will be fundamentally different from the single-particle statistics of quantum mechanics. Quantum mechanical interference takes place between different classical paths with precise amplitude and phase relations. In the double-slit experiment with walking droplets, these relations are lost since one of the paths is singled out by the droplet. To support our conclusions, we have carried out our own double-slit experiment, and our results, in particular the long and variable slit passage times of the droplets, cast strong doubt on the feasibility of the interference claimed by Couder and Fort. To understand theoretically the limitations of wave-driven particle systems as analogs to quantum mechanics, we introduce a Schrödinger equation with a source term originating from a localized particle that generates a wave while being simultaneously guided by it. We show that the ensuing particle-wave dynamics can capture some characteristics of quantum mechanics such as orbital quantization. However, the particle-wave dynamics can not reproduce quantum mechanics in general, and we show that the single-particle statistics for our model in a double-slit experiment with an additional splitter plate differs qualitatively from that of quantum mechanics.

The SNO+ experiment for neutrinoless double-beta decay

Energy Technology Data Exchange (ETDEWEB)

Lozza, Valentina; Krosigk, Belina von; Soerensen, Arnd; Zuber, Kai [Institut fuer Kern- und Teilchenphysik, Dresden (Germany)

2015-07-01

SNO+ is a large liquid scintillator based experiment that re-uses the Sudbury Neutrino Observatory detector. The detector, located 2 km underground in a mine near Sudbury, Canada, consists of a 12 m diameter acrylic vessel which will be filled with 780 tonnes of liquid scintillator. The main physics goal of SNO+ is to search for the neutrinoless double-beta (0n2b) decay of {sup 130}Te. During the double-beta phase, the liquid scintillator will be initially loaded with 0.3% natural tellurium (nearly 800 kg of {sup 130}Te). During this demonstration phase we anticipate that we will achieve a sensitivity in the region just above the inverted neutrino mass hierarchy. Recently the possibility to deploy up to 10 times more natural tellurium is being developed, by which SNO+ could explore, in the near future, deep into the parameter space for the inverted hierarchy. Designed as a general purpose neutrino experiment, SNO+ can additionally measure the reactor neutrino oscillations, geo-neutrinos in a geologically-interesting location, watch supernova neutrinos and measure low energy solar neutrinos. A first commissioning phase with the detector filled with water has started in autumn 2014, while full running with water will take place in 2015. Transition to the scintillator phase will start towards the end of 2015. The 0n2b decay phase is foreseen for the 2016.

Nuclear criticality safety: general. 6. Application of Fixed Neutron Absorbers in the New Hanford PFP Horizontal Rack Design

International Nuclear Information System (INIS)

Lan, J.S.; Miller, E.M.; Toffer, H.; Mo, B.S.

2001-01-01

The Hanford Plutonium Finishing Plant (PFP) is currently in a waste cleanup and plutonium stabilization mode. Plutonium-bearing materials are processed through thermal treatment, creating forms of oxides suitable for long-term storage. Stabilized materials at PFP are stored in a variety of cans such as the bag-less transfer cans (BTCs), which are ultimately contained in the U.S. Department of Energy (DOE) 3013 can; both cans are larger than previously used plutonium storage containers and hold more plutonium. To compensate for the increased plutonium loadings, added engineered safety features were considered in the storage facilities. The vaults in PFP, subdivided into concrete-walled cubicles, will contain both new and older cans. The DOE 3013 and BTC cans may be loaded with up to 4.4 kg of plutonium as a compound (mostly oxide). New racks that store cans horizontally are being constructed to hold both new and older containers. The loading objective is to accommodate 70 kg of plutonium per cubicle. Two design analysis approaches for the new racks were considered. The first approach incorporated neutron absorption provided by the structural materials of the rack and the cans in determining a safe configuration. A rack loading arrangement was determined as shown in Fig. 1 and specified in Table I. This approach provides compliance with criticality control requirements; however, added administrative controls were needed to accommodate a sufficient number of cans in specific locations to achieve 70 kg of plutonium per cubicle. The 4.4-kg plutonium container can be placed only in predetermined locations. The second approach evaluated the addition of a fixed neutron absorber plate along the back wall of the cubicle (Fig. 1). The location of the special plate facilitates installation of the racks and provides additional criticality safety margin beyond the first approach. Its presence permits loading of racks with up to 4.4-kg plutonium cans in any storage locations

Parametric Evaluation of Racking Performance of Platform Timber Framed Walls

OpenAIRE

Dhonju, R..; D’Amico, B..; Kermani, A..; Porteous, J..; Zhang, B..

2017-01-01

This paper provides a quantitative assessment of the racking performance of partially anchored timber framed walls, based on experimental tests. A total of 17 timber framed wall specimens, constructed from a combination of materials under different load configurations, were tested. The experimental study was designed toexamine the influence of a range of geometrical parameters, such as fastener size and spacings, wall length, arrangement of studs and horizontal members, as well as the effect ...

GreenChill Store Certification Protocol for Sub-Cooling Contained on Racks Separate from Refrigeration Equipment

Science.gov (United States)

Document describes the protocol used to determine the total load and refrigerant charge of stores that have placed all sub-cooling on a rack separate from all other commercial refrigeration equipment.

A Fragment of the Past: The System of Hotel Front Office Racks

Directory of Open Access Journals (Sweden)

Peter Szende

2017-06-01

Full Text Available Before computers and electronic systems, the heart of a hotel's front desk was a metal file system which consisted of pockets for the slips to be inserted into, called the room rack. Take a step back in time to see how these efficient systems were developed and adapted by different hotel properties.

The MAJORANA experiment: an ultra-low background search for neutrinoless double-beta decay

Energy Technology Data Exchange (ETDEWEB)

Phillips, D.; Aguayo Navarrete, Estanislao; Avignone, Frank T.; Back, Henning O.; Barabash, Alexander S.; Bergevin, M.; Bertrand, F.; Boswell, M.; Brudanin, V.; Busch, Matthew; Chan, Yuen-Dat; Christofferson, Cabot-Ann; Collar, J. I.; Combs, Dustin C.; Cooper, R. J.; Detwiler, Jason A.; Doe, Peter J.; Efremenko, Yuri; Egorov, Viatcheslav; Ejiri, H.; Elliott, Steven R.; Esterline, James H.; Fast, James E.; Fields, N.; Finnerty, P.; Fraenkle, Florian; Gehman, Victor; Giovanetti, G. K.; Green, Matthew P.; Guiseppe, Vincente; Gusey, K.; Hallin, A. L.; Hazama, R.; Henning, Reyco; Hime, Andrew; Hoppe, Eric W.; Horton, Mark; Howard, Stanley; Howe, M. A.; Johnson, R. A.; Keeter, K.; Keller, C.; Kidd, Mary; Knecht, A.; Kochetov, Oleg; Konovalov, S.; Kouzes, Richard T.; LaFerriere, Brian D.; LaRoque, B. H.; Leon, Jonathan D.; Leviner, L.; Loach, J. C.; MacMullin, S.; Marino, Michael G.; Martin, R. D.; Mei, Dong-Ming; Merriman, Jason H.; Miller, M. L.; Mizouni, Leila; Nomachi, Masaharu; Orrell, John L.; Overman, Nicole R.; Poon, Alan; Perumpilly, Gopakumar; Prior, Gersende; Radford, D. C.; Rielage, Keith; Robertson, R. G. H.; Ronquest, M. C.; Schubert, Alexis G.; Shima, T.; Shirchenko, M.; Snavely, Kyle J.; Steele, David; Strain, J.; Thomas, K.; Timkin, V.; Tornow, W.; Vanyushin, I.; Varner, R. L.; Vetter, Kai; Vorren, Kris R.; Wilkerson, J. F.; Wolfe, B. A.; Yakushev, E.; Young, A.; Yu, Chang-Hong; Yumatov, Vladimir; Zhang, C.

2012-12-01

The observation of neutrinoless double-beta decay would resolve the Majorana nature of the neutrino and could provide information on the absolute scale of the neutrino mass. The initial phase of the Majorana Experiment, known as the Demonstrator, will house 40 kg of Ge in an ultra-low background shielded environment at the 4850' level of the Sanford Underground Laboratory in Lead, SD. The objective of the Demonstrator is to validate whether a future 1-tonne experiment can achieve a background goal of one count per tonne-year in a narrow region of interest around the 76Ge neutrinoless double-beta decay peak.

Double rupture disc experience

International Nuclear Information System (INIS)

1979-01-01

Result of these observations, comparisons and evaluations can be summarized in the following list of concerns regarding the use of double rupture discs coupled to the liquid space of a steam generator that is subjected to a large leak sodium water reaction event. Single rupture disc show delayed collapse characteristics in LLTR Series I and double disc assemblies are presumed to be more complex with additional delay before opening to give pressure relief. Delayed failure increases pressures in the IHTS and must be adequately covered by design requirements. With CRBR design, the first disc may fail only partially reducing the loading on the second disc with the result that relief performance may not meet requirements

Spent fuel storage rack for BWR fuel assemblies

International Nuclear Information System (INIS)

Machado, O.; Henry, C.W.; Congleton, R.L.; Flynn, W.M.

1990-01-01

This patent describes for the use in storing nuclear fuel assemblies in a storage pool containing a coolant and having a pool floor, a fuel rack module. It comprises: a base plate to be disposed generally horizontally on the floor and having a horizontal surface area sufficient to support a fuel assemblies; uniformly spaced openings in the base plate, disposed in rows and columns throughout the surface area; fabricated cells of rectangular cross section extending over alternate openings along each row of the openings, the fabricated cells of each row being uniformly staggered by one opening with respect to the cells of its just adjacent rows so that the fabricated cells form a checkerboard like array; each of the fabricated cells having elongated walls mounted generally vertically on the base plate; each of the corners formed by the walls of each fabricated cell, which corners are internal of the periphery of the array, being disposed as closely adjacent as practicable to and face-to-face with a corner of an adjacent fabricated cell and joined by weld means so that substantially no space exists between adjacent cells. The cells being welded to their bottom ends to the base plate so that a strong compact modular structure is produced; neutron-absorbing means on the external surface of the fabricated cell walls except on the coextensive sections of the outer wall around the periphery of the array; and leveling pads are mounted under the base plate near the periphery thereof and adjustably engage the pool floor and intermediate leveling pads are mounted under cells within the fuel-rack module, the intermediate pads being uniformly disposed

Mathematical Modelling of Involute Spur Gears Manufactured by Rack Cutter

Directory of Open Access Journals (Sweden)

Tufan Gürkan YILMAZ

2016-05-01

Full Text Available In this study, mathematical modelling of asymmetric involute spur gears was situated in by Litvin approach. In this context, firstly, mathematical expressions of rack cutter which manufacture asymmetric involute spur gear, then mathematical expression of asymmetric involute spur gear were obtained by using differential geometry, coordinate transformation and gear theory. Mathematical expressions were modelled in MATLAB and output files including points of involute spur gear’s teeth were designed automatically thanks to macros.

Results from the Double Chooz experiment

Directory of Open Access Journals (Sweden)

Kaneda Michiru

2016-01-01

Full Text Available Recent results from the Double Chooz experiment on the neutrino mixing angle θ13 are presented. Two detectors are located at distances of 400m and 1050m from the reactor cores of the Chooz nuclear power plant, to measure the original neutrino flux from the reactor cores and the disappearance of neutrinos, respectively. The Far Detector has taken data since 2011 while the Near Detector started the data taking in 2014. The latest far detector only result with gadolinium capture events is sin2 2θ13=0.090+0.032.-0.029. Studies using hydrogen capture events also have been improved and the combined result of gadolinium and hydrogen capture events is obtained as sin2 2θ13 = 0.088 ± 0.033.

Corpuscular Model of Two-Beam Interference and Double-Slit Experiments with Single Photons

NARCIS (Netherlands)

Jin, Fengping; Yuan, Shengjun; De Raedt, Hans; Michielsen, Kristel; Miyashita, Seiji

We introduce an event-based corpuscular simulation model that reproduces the wave mechanical results of single-photon double-slit and two-beam interference experiments and (of a one-to-one copy of an experimental realization) of a single-photon interference experiment with a Fresnel biprism. The

Morphometrics and structure of complete baleen racks in gray whales (Eschrichtius robustus) from the Eastern North Pacific Ocean.

Science.gov (United States)

Young, Samantha; DeméRé, Thomas A; Ekdale, Eric G; Berta, Annalisa; Zellmer, Nicholas

2015-04-01

Mysticetes have evolved a novel filter feeding apparatus-baleen-an epidermal keratinous tissue composed of keratin that grows as a serial arrangement of transverse cornified laminae from the right and left sides of the palate. The structure and function of baleen varies among extant mysticete clades and this variation likely can be viewed as adaptations related to different filter feeding strategies. In one of the first morphometric studies of the full baleen apparatus, we describe the morphology of complete baleen racks in neonate, yearling and adult gray whales (Eschrichtius robustus), and note morphometric variations between age groups as well as within individual racks. Morphometric data and detailed descriptions were collected from the full baleen apparatus of three frozen specimens of E. robustus using previously derived ecologically significant and broad scale measurements of baleen. Additionally, characters of the baleen apparatus were described based on visible patterns of baleen laminae and plates on the dorsal root of the rack. Results indicate that the longest, widest, and thickest plates and laminae are found toward the posterior half of the rack, resulting in the greatest surface area for filtration of prey occurring in this region. Ontogenetic changes were also documented that reveal a progressive increase in the filter surface area of the developing baleen apparatus as baleen laminae and main plates grow in length and width. Also noted was a progressive posterior shift in the position of greatest filtration area. Histological examination of the epithelial base (Zwischensubstanz) and laminae showed basic epidermal layers, as well as gapping between layers and vacuoles. © 2015 Wiley Periodicals, Inc.

Making Sense of the Combined Degree Experience: The Example of Criminology Double Degrees

Science.gov (United States)

Wimshurst, Kerry; Manning, Matthew

2017-01-01

Little research has been undertaken on student experiences of combined degrees. The few studies report that a considerable number of students experienced difficulty with the contrasting epistemic/disciplinary demands of the component programmes. A mixed-methods approach was employed to explore the experiences of graduates from four double degrees…

A large scale double beta and dark matter experiment: GENIUS

International Nuclear Information System (INIS)

Hellmig, J.; Klapdor-Kleingrothaus, H.V.

1997-01-01

The recent results from the HEIDELBERG-MOSCOW experiment have demonstrated the large potential of double beta decay to search for new physics beyond the Standard Model. To increase by a major step the present sensitivity for double beta decay and dark matter search much bigger source strengths and much lower backgrounds are needed than used in experiments under operation at present or under construction. We present here a study of a project proposed recently, which would operate one ton of 'naked' enriched germanium-detectors in liquid nitrogen as shielding in an underground setup (GENIUS). It improves the sensitivity to neutrino masses to 0.01 eV. A ten ton version would probe neutrino masses even down to 10 -3 eV. The first version would allow to test the atmospheric neutrino problem, the second at least part of the solar neutrino problem. Both versions would allow in addition significant contributions to testing several classes of GUT models. These are especially tests of R-parity breaking supersymmetry models, leptoquark masses and mechanism and right-handed W-boson masses comparable to LHC. The second issue of the experiment is the search for dark matter in the universe. The entire MSSM parameter space for prediction of neutralinos as dark matter particles could be covered already in a first step of the full experiment with the same purity requirements, but using only 100 kg of 76 Ge or even of natural Ge making the experiment competitive to LHC in the search for supersymmetry.The layout of the proposed experiment is discussed and the shielding and purity requirements are studied using GEANT Monte Carlo simulations. As a demonstration of the feasibility of theexperiment first results of operating a 'naked' Ge detector in liquid nitrogen are presented. (orig.)

The double chooz experiment: simulation of reactor antineutrino spectra

International Nuclear Information System (INIS)

Mueller, T.

2010-01-01

The Double Chooz experiment aims to study the oscillations of electron antineutrinos produced by the Chooz nuclear power station, located in France, in the Ardennes region. It will lead to an unprecedented accuracy on the value of the mixing angle θ 13 . Improving the current knowledge on this parameter, given by the Chooz experiment, requires a reduction of both statistical and systematic errors, that is to say not only observing a large data sample, but also controlling the experimental uncertainties involved in the production and detection of electron antineutrinos. The use of two identical detectors will cancel most of the experimental systematic uncertainties limiting the sensitivity to the value of the mixing angle. We present in this thesis, simulations of reactor antineutrino spectra that were carried out in order to control the sources of systematic uncertainty related to the production of these particles by the plant. We also discuss our work on controlling the normalization error of the experiment through the precise determination of the number of target protons by a weighing measurement and through the study of the fiducial volume of the detectors which requires an accurate modeling of neutron physics. After three years of data taking with two detectors, Double Chooz will be able to disentangle an oscillation signal for sin 2 2θ 13 ≥ 0.05 (at 3σ) or, if no oscillations are observed, to put a limit of sin 2 2θ 13 ≤ 0.03 at 90% C.L. (author) [fr

Field Trial on a Rack-mounted DC Power Supply System with 80-Ah Lithium-ion Batteries

Science.gov (United States)

Matsushima, Toshio

Using an industrial lithium-ion battery that has higher energy density than conventional valve-regulated lead-acid batteries, a rack-mounted DC-power-supply system was assembled and tested at a base transceiver station (BTS) offering actual services. A nominal output voltage and maximum output current of the system is 53.5V and 20A, respectively. An 80-Ah lithium-ion battery composed of 13 cells connected in series was applied in the system and maintained in a floating charge method. The DC-power-supply system was installed in a 19-inch power rack in the telecommunications equipment box at BTS. The characteristics of the 80Ah lithium-ion battery, specifications of the DC-power-supply system and field-test results were shown in this paper.

Conceptual design of reactor TRIGA PUSPATI (RTP) spent fuel storage rack

International Nuclear Information System (INIS)

Tonny Lanyau; Mohd Fazli Zakaria; Zaredah Hashim; Ahmad Nabil Ab Rahim; Mohammad Suhaimi Kassim

2010-01-01

PUSPATI TRIGA Reactor (RTP) is a pool type research reactor with 1MW thermal power. It has been safely operated since 28 June 1982. During 28 years of safe operation, there are several systems and components of the RTP that have been maintained, repaired, upgraded and replaced in order to maintain its function and safety conditions. RTP has been proposed to be upgraded so that optimum operation of RTP could be achieved as well as fulfill the future needs. Thus, competencies and technical capabilities were needed to design and develop the reactor system. In the meantime, there is system or component need to be maintained such as fuel elements. Since early operation, most of the fuel elements still can be used and none of the fuel elements was replaced or sent for reprocessing and final disposal. Towards the power upgrading, preparation of spent fuel storage is needed for temporary storing of the fuels discharged from the reactor core. The spent fuel storage rack will be located in the spent fuel pool to accommodate the spent fuels before it is send to reprocessing or final disposal. This paper proposes the conceptual design of the spent fuel storage rack. The output of this paper focused on the physical and engineering design of the spent fuel storage. (author)

Design and Testing of a Breadboard Electrical Power Control Unit for the Fluid Combustion Facility Experiment

Science.gov (United States)

Kimnach, Greg L.; Lebron, Ramon C.

1999-01-01

The Fluid Combustion Facility (FCF) Project and the Power Technology Division at the NASA Glenn Research Center (GRC) at Lewis Field in Cleveland, OH along with the Sundstrand Corporation in Rockford, IL are jointly developing an Electrical Power Converter Unit (EPCU) for the Fluid Combustion Facility to be flown on the International Space Station (ISS). The FCF facility experiment contains three racks: A core rack, a combustion rack, and a fluids rack. The EPCU will be used as the power interface to the ISS 120V(sub dc) power distribution system by each FCF experiment rack which requires 28V(sub dc). The EPCU is a modular design which contains three 120V(sub dc)-to-28V(sub dc) full-bridge, power converters rated at 1 kW(sub e) each bus transferring input relays and solid-state, current-limiting input switches, 48 current-limiting, solid-state, output switches; and control and telemetry hardware. The EPCU has all controls required to autonomously share load demand between the power feeds and--if absolutely necessary--shed loads. The EPCU, which maximizes the usage of allocated ISS power and minimizes loss of power to loads, can be paralleled with other EPCUs. This paper overviews the electrical design and operating characteristics of the EPCU and presents test data from the breadboard design.

Fixing Trailer Hitch for Roof Rack of Cargos

Directory of Open Access Journals (Sweden)

Darina Matisková

2017-02-01

Full Text Available This article presents a new technical solution of fixing trailer hitch which serves as a connection between single track vehicle and cargo, mainly light trailer. They are manufactured from steel girder and nets which are constructed by point welding. They are designed to indicate the necessary solidity and the required load bearing capacity of the cargo. The application of roof racks is universal and these products are in great demand in the field of game management. There are a lot of trailer hitches which the manufacturers tailor to customers´ demands. The stated technical solution is subject of published industrial utility model at the Industrial property office of the Slovak republic.

Double-quarkonium production at a fixed-target experiment at the LHC (AFTER@LHC)

CERN Document Server

Lansberg, Jean-Philippe

2015-01-01

We present predictions for double-quarkonium production in the kinematical region relevant for the proposed fixed-target experiment using the LHC beams (dubbed as AFTER@LHC). These include all spin-triplet S -wave charmonium and bottomonium pairs, i.e. Psi(n_1S) + Psi(n_2S), Psi(n_1S) + Upsilon(m_1S) and Upsilon(m_1S) + Upsilon(m_2S ) with n_1,n_2 = 1,2 and m_1,m_2 = 1,2,3. We calculate the contributions from double-parton scatterings and single-parton scatterings. With an integrated luminosity of 20 fb-1 to be collected at AFTER@LHC, we find that the yields for double-charmonium production are large enough for differential distribution measurements. We discuss some differential distributions for J/Psi + J/Psi production, which can help to study the physics of double-parton and single-parton scatterings in a new energy range and which might also be sensitive to double intrinsic c-bar(c) coalescence at large negative Feynman x.

Monte Carlo Simulation for the Majorana Neutrinoless Double-beta Decay Experiment

International Nuclear Information System (INIS)

Henning, Reyco; Majorana Collaboration

2005-01-01

The Majorana experiment is a proposed HPGe detector array that will primarily search for neutrinoless double-beta decay and dark matter. It will rely on pulse-shape discrimination and crystal segmentation to suppress backgrounds following careful materials selection. A critical aspect of the design phase of Majorana is a reliable simulation of the detector response, pulse formation, and its radioactive backgrounds. We are developing an adaptable and complete simulation based on GEANT 4 to address these requirements and the requirements of a modern, large collaboration experiment. The salient aspects of the simulation are presented. The Majorana experiment is presented in a parallel poster by Kareem Kazkaz

Combat Ration Network for Technology Implementation. Retort Racks for Polymeric Trays in 1400 Style Spray Retorts

National Research Council Canada - National Science Library

Bruins, Henderikus B; Coburn, John F

2003-01-01

The objective of this project was to design a retort rack that would maximize the retort capacity of a 1400 style spray retort and to select a material that would withstand the harsh retort spray environment...

Double-slit experiment with single wave-driven particles and its relation to quantum mechanics

DEFF Research Database (Denmark)

Andersen, Anders Peter; Madsen, Jacob; Reichelt, Christian Günther

2015-01-01

even though it is possible to determine unambiguously which slit the walking droplet passes. Here we argue, however, that the single-particle statistics in such an experiment will be fundamentally different from the single-particle statistics of quantum mechanics. Quantum mechanical interference takes...... place between different classical paths with precise amplitude and phase relations. In the double-slit experiment with walking droplets, these relations are lost since one of the paths is singled out by the droplet. To support our conclusions, we have carried out our own double-slit experiment, and our...... results, in particular the long and variable slit passage times of the droplets, cast strong doubt on the feasibility of the interference claimed by Couder and Fort. To understand theoretically the limitations of wave-driven particle systems as analogs to quantum mechanics, we introduce a Schro...

Correlation between fuel rack sticking and unintentional re-starting of EDG

Energy Technology Data Exchange (ETDEWEB)

Kim, Young Cheol; Chung, Woo geun; Kang, Seung Hee; Kim, Myeong hoon [KHNP CRI, Daejeon (Korea, Republic of)

2016-10-15

The Emergency Diesel Generator (EDG) was being tested after overhaul maintenance. While the EDG was running at the rated speed (450 rpm), an operator pressed the manual stop button. But the EDG failed to stop and unintentionally started again. After the unintentional re-start, the EDG maintained running speed of 340 rpm. In the category of a governing system, this paper analyzes the cause of unintentional restart of the EDG that unintentionally re-started and maintained a speed at 340 rpm. The results of the analysis were then verified by a test run. Finally, we identified a correlation between fuel rack sticking and unintentional re-starting of the EDG. An analysis was conducted to confirm the cause of an EDG which was unintentionally restarting and running at 340rpm (rated speed is 450 rpm). Through a test run, it was confirmed that the results of the analysis are correct. The cause of the EDG unintentionally restarting was that it still rotated at 55 rpm over the minimum starting speed at the moment when the shutdown cylinder stopped blocking the fuel, because of a stuck fuel rack at the R7 cylinder. At the same time, the fuel that had been supplied into the cylinders (combustion chamber) by the governing system exploded and the EDG restarted unintentionally.

Study of compact X-ray laser pumped by pulse-train laser. Double-target experiment

International Nuclear Information System (INIS)

Yamaguchi, Naohiro; Fujikawa, Chiemi; Hara, Tamio

2000-01-01

We have been developing a tabletop x-ray laser based on the recombination plasma scheme. An advanced experiment has been started to improve x-ray laser output substantially. Two 11-mm-long laser produced plasmas were produced so that their axis aligned into a line, the double-target configuration. X-ray intensity of the 15.47 nm transition line of the Li-like Al ion has been enhanced in the double-target configuration. (author)

Thermal neutron flux measurements in the rotary specimen rack of the IPR-R1 TRIGA reactor

Energy Technology Data Exchange (ETDEWEB)

Souza, Rose Mary G. do Prado; Rodrigues, Rogério R.; Souza, Luiz Claudio A., E-mail: souzarm@cdtn.br, E-mail: rrr@cdtn.br, E-mail: lcas@cdtn.br [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN-MG), Belo Horizonte, MG (Brazil)

2017-07-01

The thermal neutron flux in the rotary specimen rack of the IPR-R1 TRIGA reactor at the Nuclear Technology Development Center (CDTN), Belo Horizonte, Brazil, has been measured by the neutron activation method, using bare and cadmium covered gold foils. Those foils were irradiated in the rotary specimen rack with the reactor at 100 kW. The reactor core configuration has 63 fuel elements, composed of 59 original aluminum-clad elements and 4 stainless steel-clad fuel elements. The gamma activities of the foils were measured using Ge spectrometer. The perturbations of the thermal neutron flux caused by the introduction of an absorbing foil into the medium were considered in order to obtain accurate determination of the flux. The thermal neutron flux obtained was 7.4 x 10{sup 11} n.cm{sup -2}.s{sup -1}. (author)

Neutrino oscillations - the Double Chooz experiment

Energy Technology Data Exchange (ETDEWEB)

Lasserre, Th. [CEA Saclay, Dept. d' Astrophysique, de Physique des Particules de Physique Nucleaire et de l' Instrumentation Associee (DSM/DAPNIA/SPP/APC), 91- Gif sur Yvette (France)

2007-07-01

{theta}{sub 13} is the mixing angle that couples the field of the neutrino number 3 (the heaviest) to the electron field. The Double Chooz experiment will use 2 identical detectors, near the Chooz nuclear reactor cores to measure the last undetermined mixing angle {theta}{sub 13}. The basic principle of the multi-detector concept is the cancellation of the reactor-induced systematic errors. The first detector will be installed in the existing underground laboratory (1050 meters away from the plant station) that was used in the first Chooz experiment in the nineties. The second detector will be constructed from 2009 in a new neutrino laboratory, located down a 45 m well that will be excavated 300 m away from the reactors. An average visible neutrino rate of 55 (550) events per day is expected to be detected inside the far (near) detector, taking into account the various inefficiencies, if no oscillations. The near detector will perform a measurement of the anti-neutrino flux and its energy spectrum with an unprecedented accuracy and for a long period (3 years). These huge statistics will also be exploited to monitor changes in the relative amounts of U{sup 235} and Pu{sup 239} in the core, paving the way to use neutrino detection for safeguards applications. (A.C.)

Insert Concepts for the Material Science Research Rack (MSRR-1) of the Material Science Research Facility (MSRF) on the International Space Station (ISS)

Science.gov (United States)

Crouch, Myscha; Carswell, Bill; Farmer, Jeff; Rose, Fred; Tidwell, Paul

2000-01-01

The Material Science Research Rack I (MSRR-1) of the Material Science Research Facility (MSRF) contains an Experiment Module (EM) being developed collaboratively by NASA and the European Space Agency (ESA). This NASA/ESA EM will accommodate several different removable and replaceable Module Inserts (MIs) which are installed on orbit NASA's planned inserts include the Quench Module Insert (QMI) and the Diffusion Module Insert (DMI). The QMI is a high-gradient Bridgman-type vacuum furnace with quench capabilities used for experiments on directional solidification of metal alloys. The DMI is a vacuum Bridgman-Stockbarger-type furnace for experiments on Fickian and Soret diffusion in liquids. This paper discusses specific design features and performance capabilities of each insert. The paper also presents current prototype QMI hardware analysis and testing activities and selected results.

The CUORE neutrinoless double-beta decay experiment

International Nuclear Information System (INIS)

Banks, T.I.

2014-01-01

CUORE is an upcoming experiment designed to search for neutrinoless double-beta decay (0νββ) decay in 130 Te. Observation of the process would be a major finding because it would unambiguously establish that neutrinos are Majorana particles (i.e., their own antiparticles) as well as provide information about the absolute neutrino mass scale. The CUORE detector will consist of 988 identical TeO 2 crystal bolometers (containing 206 kg of 130 Te in total) arranged into 19 towers and cooled to about 10 mK at the underground Gran Sasso National Laboratory (LNGS), Italy, which provides the low-background environment necessary for rare event searches of this kind. A predecessor experiment, Cuoricino, ran from 2003-2008 at LNGS and served as a learning ground for CUORE, which will be 20 times larger and exhibit much lower backgrounds. The CUORE detector assembly line has produced its first tower, designated CUORE-0, which is expected to come online in the former Cuoricino cryostat in October 2012 and take data for about 2 years while 19 CUORE towers are assembled. CUORE data taking is expected for 2015-2019. (author)

LBL/UCSB 76Ge double beta decay experiment: first results

International Nuclear Information System (INIS)

Goulding, F.S.; Cork, C.P.; Landis, D.A.

1984-10-01

A paper given at the IEEE Nuclear Science Symposium last year presented the scientific justification for this experiment and discussed the design of the detector system. At the present time two of the dual detector systems (i.e., four out of a final total of eight detectors) are operating in the complete active/passive shield in the low background laboratory at LBL. Early results (1620 h) of an experiment using two detectors yield a limit of 4 x 10 22 years (68% confidence) for the half life of the neutrinoless double beta decay (ββ/sub o nu/) of 76 Ge. Although this experiment was carried out above ground, the result approaches those achieved by other groups in deep underground laboratories. Based on studies of the origins of background in our system, we hope to reach a limit of 3 x 10 23 years (or more) in a two month/four detector experiment to be carried out soon in an underground facility

Double Beta Decay Experiments

International Nuclear Information System (INIS)

Piepke, A.

2005-01-01

The experimental observation of neutrino oscillations and thus neutrino mass and mixing gives a first hint at new particle physics. The absolute values of the neutrino mass and the properties of neutrinos under CP-conjugation remain unknown. The experimental investigation of the nuclear double beta decay is one of the key techniques for solving these open problems

The neutrino experiment Double Chooz and data analysis with the near detector

Energy Technology Data Exchange (ETDEWEB)

Franke, Michael Werner

2016-03-07

During the last years there has been a huge progress in the field of neutrino physics. Neutrino oscillations are well established and almost all parameters, except a possible CP-violating phase, are determined to high precision. One experiment providing a precise measurement of the neutrino mixing angle θ{sub 13} is the Double Chooz reactor antineutrino experiment. The reactor antineutrinos are detected via the inverse beta decay in two identical liquid scintillator based detectors. A few years ago, the value of θ{sub 13} was unknown and only an upper limit existed. Double Chooz was the first reactor antineutrino experiment presenting a result for a nonzero value of θ{sub 13}. The value for sin{sup 2}2θ{sub 13} from the latest Double Chooz publication is 0.090{sup +0.032}{sub -0.029}. As part of this thesis, an infrastructure for filling the Double Chooz near detector was established and 190 m{sup 3} of detector liquids were prepared successfully. The filling process was optimized to allow an efficient filling of the near detector. The total operation time was reduced to only 22 days. Compared to the far detector filling time of 2 months, this is a great improvement. The development of a completely new level measurement system was as well part of this thesis. Due to the excellent performance of the level measurement system, the hard restrictions for the safety of the Double Chooz detector were met during the entire filling process. Several power glitches and network failures did not harm the system and did not result in any loss of data. These irregularities and the simple maintenance and repair possibilities certify the success of the design concept for the new level measurement system. For this thesis, data from the Double Chooz near detector with a total live time of 110.4 days was used. The mass concentrations of uranium and thorium in the near detector were determined using BiPo coincidences. These events originate from the β-decay of {sup 214}Bi and {sup

Research and Development Supporting a Next Generation Germanium Double Beta Decay Experiment

Science.gov (United States)

Rielage, Keith; Elliott, Steve; Chu, Pinghan; Goett, Johnny; Massarczyk, Ralph; Xu, Wenqin

2015-10-01

To improve the search for neutrinoless double beta decay, the next-generation experiments will increase in source mass and continue to reduce backgrounds in the region of interest. A promising technology for the next generation experiment is large arrays of Germanium p-type point contact detectors enriched in 76-Ge. The experience, expertise and lessons learned from the MAJORANA DEMONSTRATOR and GERDA experiments naturally lead to a number of research and development activities that will be useful in guiding a future experiment utilizing Germanium. We will discuss some R&D activities including a hybrid cryostat design, background reduction in cabling, connectors and electronics, and modifications to reduce assembly time. We acknowledge the support of the U.S. Department of Energy through the LANL/LDRD Program.

Method of assembling spent nuclear fuel storage rack

International Nuclear Information System (INIS)

Igarashi, Ryokichi; Hasegawa, Hidenobu.

1982-01-01

Purpose: To improve the safety of a spent fuel storage rack by stably installing the spent fuel in a pool without using supporting beams. Constitution: A restricted unit is composed of a plurality of spuare cylinders. A plurality of such restricted units are aligned in a direction perpendicularly to the arraying direction of the cylinders in the respective restricted units, are coupled with long connecting plates, and are fixed by welding on a common small base, thereby forming a restricted body. According to such assembling method, a plurality of restricted bodies are connected in a direction that the respective restricted bodies are readily overturned, and are secured to the common base. Accordingly, the restricted bodies can be stably installed in a pool without using supporting beams as the conventional one. (Sekiya, K.)

Status of the Frejus experiment on the neutrinoless double beta decay of the 76Ge

International Nuclear Information System (INIS)

Morales, A.; Nunez-Lagos, R.; Morales, J.; Puimedon, J.; Villar, J.A.; Dassie, D.; Hubbert, Ph.; Leccia, F.; Mennrath, P.; Villard, M.

1987-01-01

A brief account of the design, experimental set up and status of the Frejus experiments on the neutrinoless double beta decay of 76 Ge is presented. The theoretical implications and expectatives of this experimental research are analized. A comparison with other dedicated experiments is also reported. (author)

A simulation-optimization heuristic for configuring a selective pallet rack system Heurístico de simulación-optimización para la configuración de un sistema de estantería selectiva simple

Directory of Open Access Journals (Sweden)

Mario C Vélez Gallego

2012-04-01

Full Text Available A discrete event simulation-optimization heuristic is presented for configuring a selective pallet rack system. To the rack system under study pallets arrive dynamically over time to be stored for a given period of time. The storage duration, arrival time and pallet height are assumed to be continuous random variables with known density functions. In such a system, if there is no available slot in the rack to store an arriving pallet, it is placed on the floor. The proposed heuristic aims at minimizing the number of racking banks needed so that the long term proportion of pallets that are placed in a rack slot reaches a minimum pre-specified value. The computational experiments conducted suggest that the proposed heuristic effectively solves the problem under study.En este artículo se presenta un heurístico de simulación-optimización para la configuración de un sistema de almacenamiento en estantería selectiva simple. Al sistema de almacenamiento objeto del estudio llegan pallets dinámicamente en el tiempo para ser almacenados por un periodo de tiempo. Se asume que la duración del almacenamiento, el instante de llegada y la altura de los pallets son variables aleatorias continuas con funciones de densidad conocidas. En este sistema, si al momento de llegada de un pallet no hay disponible una posición en la estantería en la que éste se pueda almacenar, el pallet se almacena en el suelo. El heurístico propuesto busca minimizar en el número de módulos de estantería necesarios de tal manera que en el largo plazo la proporción de pallets ubicados en la estantería alcance un valor mínimo preestablecido. Los experimentos computacionales llevados a cabo sugieren que el heurístico propuesto es efectivo para resolver el problema en estudio.

Ackermann's steering principle behind the optimization of six-bar steering linkages having a rectilinear translating rack and having an infinite to the third number of function-cognates

NARCIS (Netherlands)

Dijksman, E.A.

2000-01-01

Many times a pinion-wheel meshing with a rectilinear moving rack steers the front-wheels of a car having a fixed axis in the rear. The rack then normally translates in its own direction parallel to the fixed line which connects the two fusées. Also the wheelarms, being rigidly attached to the

Combining and comparing neutrinoless double beta decay experiments using different nuclei

Science.gov (United States)

Bergström, Johannes

2013-02-01

We perform a global fit of the most relevant neutrinoless double beta decay experiments within the standard model with massive Majorana neutrinos. Using Bayesian inference makes it possible to take into account the theoretical uncertainties on the nuclear matrix elements in a fully consistent way. First, we analyze the data used to claim the observation of neutrinoless double beta decay in 76Ge, and find strong evidence (according to Jeffrey's scale) for a peak in the spectrum and moderate evidence for that the peak is actually close to the energy expected for the neutrinoless decay. We also find a significantly larger statistical error than the original analysis, which we include in the comparison with other data. Then, we statistically test the consistency between this claim with that of recent measurements using 136Xe. We find that the two data sets are about 40 to 80 times more probable under the assumption that they are inconsistent, depending on the nuclear matrix element uncertainties and the prior on the smallest neutrino mass. Hence, there is moderate to strong evidence of incompatibility, and for equal prior probabilities the posterior probability of compatibility is between 1.3% and 2.5%. If one, despite such evidence for incompatibility, combines the two data sets, we find that the total evidence of neutrinoless double beta decay is negligible. If one ignores the claim, there is weak evidence against the existence of the decay. We also perform approximate frequentist tests of compatibility for fixed ratios of the nuclear matrix elements, as well as of the no signal hypothesis. Generalization to other sets of experiments as well as other mechanisms mediating the decay is possible.

SCORHE: a novel and practical approach to video monitoring of laboratory mice housed in vivarium cage racks.

Science.gov (United States)

Salem, Ghadi H; Dennis, John U; Krynitsky, Jonathan; Garmendia-Cedillos, Marcial; Swaroop, Kanchan; Malley, James D; Pajevic, Sinisa; Abuhatzira, Liron; Bustin, Michael; Gillet, Jean-Pierre; Gottesman, Michael M; Mitchell, James B; Pohida, Thomas J

2015-03-01

The System for Continuous Observation of Rodents in Home-cage Environment (SCORHE) was developed to demonstrate the viability of compact and scalable designs for quantifying activity levels and behavior patterns for mice housed within a commercial ventilated cage rack. The SCORHE in-rack design provides day- and night-time monitoring with the consistency and convenience of the home-cage environment. The dual-video camera custom hardware design makes efficient use of space, does not require home-cage modification, and is animal-facility user-friendly. Given the system's low cost and suitability for use in existing vivariums without modification to the animal husbandry procedures or housing setup, SCORHE opens up the potential for the wider use of automated video monitoring in animal facilities. SCORHE's potential uses include day-to-day health monitoring, as well as advanced behavioral screening and ethology experiments, ranging from the assessment of the short- and long-term effects of experimental cancer treatments to the evaluation of mouse models. When used for phenotyping and animal model studies, SCORHE aims to eliminate the concerns often associated with many mouse-monitoring methods, such as circadian rhythm disruption, acclimation periods, lack of night-time measurements, and short monitoring periods. Custom software integrates two video streams to extract several mouse activity and behavior measures. Studies comparing the activity levels of ABCB5 knockout and HMGN1 overexpresser mice with their respective C57BL parental strains demonstrate SCORHE's efficacy in characterizing the activity profiles for singly- and doubly-housed mice. Another study was conducted to demonstrate the ability of SCORHE to detect a change in activity resulting from administering a sedative.

The Majorana Zero-Neutrino Double-Beta Decay Experiment White Paper

International Nuclear Information System (INIS)

Gaitskell, R.; Barabash, A.; Konovalov, S.; Stekhanov, V.; Umatov, V.; Brudanin, V.; Egorov, S.; Webb, J.; Miley, Harry S.; Aalseth, Craig E.; Anderson, Dale N.; Bowyer, Ted W.; Brodzinski, Ronald L.; Jordan, David B.; Kouzes, Richard T.; Smith, Eric E.; Thompson, Robert C.; Warner, Ray A.; Tornow, W.; Young, A.; Collar, J.I.; Avignone, Frank T.; Palms, John M.; Doe, P J.; Elliott, Steven R.; Kazkaz, K.; Robertson, Hamish; Wilkerson, John

2002-01-01

The goal of the Majorana Experiment is to determine the effective Majorana mass of the electron neutrino. Detection of the neutrino mass implied by oscillation results in within our grasp. This exciting physics goal is best pursued using double-beta decay of germanium because of the historical and emerging advances in eliminating competing signals from radioactive backgrounds. The Majorana Experiment will consist of a large mass of 76Ge in the form of high-resolution detectors deep underground, searching for a sharp peak at the BB endpoint. We present here an overview of the entire project in order to help put in perspective the scope, the level and technical risk, and the readiness of the Collaboration to begin the undertaking

Video Monitoring and Analysis System for Vivarium Cage Racks | NCI Technology Transfer Center | TTC

Science.gov (United States)

This invention pertains to a system for continuous observation of rodents in home-cage environments with the specific aim to facilitate the quantification of activity levels and behavioral patterns for mice housed in a commercial ventilated cage rack.  The National Cancer Institute’s Radiation Biology Branch seeks partners interested in collaborative research to co-develop a video monitoring system for laboratory animals.

Neutrinoless double-beta decay search with CUORE and CUORE-0 experiments

Directory of Open Access Journals (Sweden)

Moggi N.

2015-01-01

Full Text Available The Cryogenic Underground Observatory for Rare Events (CUORE is an upcoming experiment designed to search for the neutrinoless double-beta decays. Observation of the process would unambiguously establish that neutrinos are Majorana particles and provide information on their absolute mass scale hierarchy. CUORE is now under construction and will consist of an array of 988 TeO2 crystal bolometers operated at 10 mK, but the first tower (CUORE-0 is already taking data. The experimental techniques used will be presented as well as the preliminary CUORE-0 results. The current status of the full-mass experiment and its expected sensitivity will then be discussed.

Impact Analysis for Fuel Assemblies in Spent Fuel Storage Rack

International Nuclear Information System (INIS)

Oh, Jinho

2013-01-01

The design and structural integrity evaluation of a spent fuel storage rack (SFSR) utilized for storing and protecting the spent fuel assemblies generated during the operation of a reactor are very important in terms of nuclear safety and waste management. The objective of this study is to show the validity of the SFSR design as well as fuel assembly through a structural integrity evaluation based on a numerical analysis. In particular, a dynamic time history analysis considering the gaps between the fuel assemblies and the walls of the storage cell pipes in the SFSR was performed to check the structural integrity of the fuel assembly and storage cell pipe

Impact Analysis for Fuel Assemblies in Spent Fuel Storage Rack

Energy Technology Data Exchange (ETDEWEB)

Oh, Jinho [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2013-07-01

The design and structural integrity evaluation of a spent fuel storage rack (SFSR) utilized for storing and protecting the spent fuel assemblies generated during the operation of a reactor are very important in terms of nuclear safety and waste management. The objective of this study is to show the validity of the SFSR design as well as fuel assembly through a structural integrity evaluation based on a numerical analysis. In particular, a dynamic time history analysis considering the gaps between the fuel assemblies and the walls of the storage cell pipes in the SFSR was performed to check the structural integrity of the fuel assembly and storage cell pipe.

Double shell planar experiments on OMEGA

Science.gov (United States)

Dodd, E. S.; Merritt, E. C.; Palaniyappan, S.; Montgomery, D. S.; Daughton, W. S.; Schmidt, D. W.; Cardenas, T.; Wilson, D. C.; Loomis, E. N.; Batha, S. H.; Ping, Y.; Smalyuk, V. A.; Amendt, P. A.

2017-10-01

The double shell project is aimed at fielding neutron-producing capsules at the National Ignition Facility (NIF), in which an outer low-Z ablator collides with an inner high-Z shell to compress the fuel. However, understanding these targets experimentally can be challenging when compared with conventional single shell targets. Halfraum-driven planar targets at OMEGA are being used to study physics issues important to double shell implosions outside of a convergent geometry. Both VISAR and radiography through a tube have advantages over imaging through the hohlraum and double-shell capsule at NIF. A number physics issues are being studied with this platform that include 1-d and higher dimensional effects such as defect-driven hydrodynamic instabilities from engineering features. Additionally, the use of novel materials with controlled density gradients require study in easily diagnosed 1-d systems. This work ultimately feeds back into the NIF capsule platform through manufacturing tolerances set using data from OMEGA. Supported under the US DOE by the LANS, LLC under contract DE-AC52-06NA25396. LA-UR-17-25386.

Results on Neutrinoless Double-β Decay of Ge76 from Phase I of the GERDA Experiment

Science.gov (United States)

Agostini, M.; Allardt, M.; Andreotti, E.; Bakalyarov, A. M.; Balata, M.; Barabanov, I.; Barnabé Heider, M.; Barros, N.; Baudis, L.; Bauer, C.; Becerici-Schmidt, N.; Bellotti, E.; Belogurov, S.; Belyaev, S. T.; Benato, G.; Bettini, A.; Bezrukov, L.; Bode, T.; Brudanin, V.; Brugnera, R.; Budjáš, D.; Caldwell, A.; Cattadori, C.; Chernogorov, A.; Cossavella, F.; Demidova, E. V.; Domula, A.; Egorov, V.; Falkenstein, R.; Ferella, A.; Freund, K.; Frodyma, N.; Gangapshev, A.; Garfagnini, A.; Gotti, C.; Grabmayr, P.; Gurentsov, V.; Gusev, K.; Guthikonda, K. K.; Hampel, W.; Hegai, A.; Heisel, M.; Hemmer, S.; Heusser, G.; Hofmann, W.; Hult, M.; Inzhechik, L. V.; Ioannucci, L.; Janicskó Csáthy, J.; Jochum, J.; Junker, M.; Kihm, T.; Kirpichnikov, I. V.; Kirsch, A.; Klimenko, A.; Knöpfle, K. T.; Kochetov, O.; Kornoukhov, V. N.; Kuzminov, V. V.; Laubenstein, M.; Lazzaro, A.; Lebedev, V. I.; Lehnert, B.; Liao, H. Y.; Lindner, M.; Lippi, I.; Liu, X.; Lubashevskiy, A.; Lubsandorzhiev, B.; Lutter, G.; Macolino, C.; Machado, A. A.; Majorovits, B.; Maneschg, W.; Misiaszek, M.; Nemchenok, I.; Nisi, S.; O'Shaughnessy, C.; Pandola, L.; Pelczar, K.; Pessina, G.; Pullia, A.; Riboldi, S.; Rumyantseva, N.; Sada, C.; Salathe, M.; Schmitt, C.; Schreiner, J.; Schulz, O.; Schwingenheuer, B.; Schönert, S.; Shevchik, E.; Shirchenko, M.; Simgen, H.; Smolnikov, A.; Stanco, L.; Strecker, H.; Tarka, M.; Ur, C. A.; Vasenko, A. A.; Volynets, O.; von Sturm, K.; Wagner, V.; Walter, M.; Wegmann, A.; Wester, T.; Wojcik, M.; Yanovich, E.; Zavarise, P.; Zhitnikov, I.; Zhukov, S. V.; Zinatulina, D.; Zuber, K.; Zuzel, G.

2013-09-01

Neutrinoless double beta decay is a process that violates lepton number conservation. It is predicted to occur in extensions of the standard model of particle physics. This Letter reports the results from phase I of the Germanium Detector Array (GERDA) experiment at the Gran Sasso Laboratory (Italy) searching for neutrinoless double beta decay of the isotope Ge76. Data considered in the present analysis have been collected between November 2011 and May 2013 with a total exposure of 21.6 kg yr. A blind analysis is performed. The background index is about 1×10-2counts/(keVkgyr) after pulse shape discrimination. No signal is observed and a lower limit is derived for the half-life of neutrinoless double beta decay of Ge76, T1/20ν>2.1×1025yr (90% C.L.). The combination with the results from the previous experiments with Ge76 yields T1/20ν>3.0×1025yr (90% C.L.).

The U238 antineutrino spectrum in the Double Chooz experiment

Energy Technology Data Exchange (ETDEWEB)

Haag, Nils; Oberauer, Lothar; Potzel, Walter; Schreckenbach, Klaus [Technische Universitaet, Muenchen (Germany); Lachenmaier, Tobias [Eberhard Karls Universitaet, Tuebingen (Germany)

2011-07-01

The DoubleChooz experiment aims at the determination of the unknown neutrino mixing parameter {Theta}{sub 13}. Two liquid scintillator detectors will measure an electron antineutrino disappearance at the Chooz site in the French ardennes. In order to improve the sensitivity, the antineutrino spectrum emitted by the Chooz reactor cores has to be determined with high accuracy. This talk focusses on the U238 spectrum, which is the only contributing spectrum, that was not measured until now. The final U238 beta spectrum is presented, and its implementation into the analysis framework is shown.

Experiments on ion acoustic typed double layers

International Nuclear Information System (INIS)

Chan, C.; Cho, M.H.; Intrator, T.; Hershkowitz, N.

1984-01-01

The formation of small amplitude double layers with potential drops the order of the electron temperature, was examined experimentally by pulsing a grid and thereby changing the electron drift across the target chamber of a triple plasma device. The rarefactive part of a long wavelength, low frequency ion wave grew in amplitude due to the presence of slowly drifting electrons. The corresponding current limitation led to the formation of the double layers. Depending on the plasma conditions, the asymmetric double layers either transform into a weak monotonic layer, a propagating shock, or a series of rarefactive solitary pulses. The rarefactive pulses propagate with Mach number less than one and resemble solitary plasma holes with density cavities in both the electron and the ion density profiles

Probing Pre-and In-Service Physics Teachers' Knowledge Using the Double-Slit Thought Experiment

Science.gov (United States)

Asikainen, Mervi A.; Hirvonen, Pekka E.

2014-01-01

This study describes the use of the double-slit thought experiment as a diagnostic tool for probing physics teachers' understanding. A total of 9 pre-service teachers and 18 in-service teachers with a variety of different experience in modern physics teaching at the upper secondary level responded in a paper-and-pencil test and three of these…

Development of a level-1 trigger and timing system for the Double Chooz neutrino experiment

International Nuclear Information System (INIS)

Reinhold, Bernd

2009-01-01

The measurement of the mixing angle θ 13 is the goal of several running and planned experiments. The experiments are either accelerator based (super)beam experiments (e.g. MINOS, T2K, Nova) or reactor anti-neutrino disappearance experiments (e.g. Daya Bay, RENO or Double Chooz). In order to measure or constrain θ 13 with the Double Chooz experiment the overall systematic errors have to be controlled at the one-percent or sub-percent level. The limitation of the systematic errors is achieved through various means and techniques. E.g. the experiment consists of two identical detectors at different baselines, which allow to make a differential anti-neutrino flux measurement, where basically only relative normalisation errors remain. The requirements on the systematic errors put also strong constraints on the quality of all components and materials used for both detectors, most prominently on the stability and radiopurity of the scintillator, the photomultiplier tubes, the vessels containing the detector liquids and the shielding against ambient radioactivity. The readout electronics, trigger and data acquisition system have to operate reliably as an integrated and highly efficient whole over several years. The trigger is provided by the Level-1 Trigger and Timing System, which is the subject of this thesis. It has to provide a highly efficient trigger (at the 0.1% level) for neutrino-induced events as well as for several types of background events. Its decision is realized in hardware and based on energy depositions in the muon veto and the target region. The Level-1 Trigger and Timing System furthermore provides a common System Clock and an absolute timestamp for each event. The Level-1 Trigger and Timing System consists of two types of VME modules, several Trigger Boards and a Trigger Master Board, which have been custom-designed and developed in the electronics workshop of our institute for this experiment and purpose, starting in 2005. In this thesis all

Development of a level-1 trigger and timing system for the Double Chooz neutrino experiment

Energy Technology Data Exchange (ETDEWEB)

Reinhold, Bernd

2009-02-25

The measurement of the mixing angle {theta}{sub 13} is the goal of several running and planned experiments. The experiments are either accelerator based (super)beam experiments (e.g. MINOS, T2K, Nova) or reactor anti-neutrino disappearance experiments (e.g. Daya Bay, RENO or Double Chooz). In order to measure or constrain {theta}{sub 13} with the Double Chooz experiment the overall systematic errors have to be controlled at the one-percent or sub-percent level. The limitation of the systematic errors is achieved through various means and techniques. E.g. the experiment consists of two identical detectors at different baselines, which allow to make a differential anti-neutrino flux measurement, where basically only relative normalisation errors remain. The requirements on the systematic errors put also strong constraints on the quality of all components and materials used for both detectors, most prominently on the stability and radiopurity of the scintillator, the photomultiplier tubes, the vessels containing the detector liquids and the shielding against ambient radioactivity. The readout electronics, trigger and data acquisition system have to operate reliably as an integrated and highly efficient whole over several years. The trigger is provided by the Level-1 Trigger and Timing System, which is the subject of this thesis. It has to provide a highly efficient trigger (at the 0.1% level) for neutrino-induced events as well as for several types of background events. Its decision is realized in hardware and based on energy depositions in the muon veto and the target region. The Level-1 Trigger and Timing System furthermore provides a common System Clock and an absolute timestamp for each event. The Level-1 Trigger and Timing System consists of two types of VME modules, several Trigger Boards and a Trigger Master Board, which have been custom-designed and developed in the electronics workshop of our institute for this experiment and purpose, starting in 2005. In

The large enriched germanium experiment for neutrinoless double beta decay (LEGEND)

Science.gov (United States)

Abgrall, N.; Abramov, A.; Abrosimov, N.; Abt, I.; Agostini, M.; Agartioglu, M.; Ajjaq, A.; Alvis, S. I.; Avignone, F. T.; Bai, X.; Balata, M.; Barabanov, I.; Barabash, A. S.; Barton, P. J.; Baudis, L.; Bezrukov, L.; Bode, T.; Bolozdynya, A.; Borowicz, D.; Boston, A.; Boston, H.; Boyd, S. T. P.; Breier, R.; Brudanin, V.; Brugnera, R.; Busch, M.; Buuck, M.; Caldwell, A.; Caldwell, T. S.; Camellato, T.; Carpenter, M.; Cattadori, C.; Cederkäll, J.; Chan, Y.-D.; Chen, S.; Chernogorov, A.; Christofferson, C. D.; Chu, P.-H.; Cooper, R. J.; Cuesta, C.; Demidova, E. V.; Deng, Z.; Deniz, M.; Detwiler, J. A.; Di Marco, N.; Domula, A.; Du, Q.; Efremenko, Yu.; Egorov, V.; Elliott, S. R.; Fields, D.; Fischer, F.; Galindo-Uribarri, A.; Gangapshev, A.; Garfagnini, A.; Gilliss, T.; Giordano, M.; Giovanetti, G. K.; Gold, M.; Golubev, P.; Gooch, C.; Grabmayr, P.; Green, M. P.; Gruszko, J.; Guinn, I. S.; Guiseppe, V. E.; Gurentsov, V.; Gurov, Y.; Gusev, K.; Hakenmüeller, J.; Harkness-Brennan, L.; Harvey, Z. R.; Haufe, C. R.; Hauertmann, L.; Heglund, D.; Hehn, L.; Heinz, A.; Hiller, R.; Hinton, J.; Hodak, R.; Hofmann, W.; Howard, S.; Howe, M. A.; Hult, M.; Inzhechik, L. V.; Csáthy, J. Janicskó; Janssens, R.; Ješkovský, M.; Jochum, J.; Johansson, H. T.; Judson, D.; Junker, M.; Kaizer, J.; Kang, K.; Kazalov, V.; Kermadic, Y.; Kiessling, F.; Kirsch, A.; Kish, A.; Klimenko, A.; Knöpfle, K. T.; Kochetov, O.; Konovalov, S. I.; Kontul, I.; Kornoukhov, V. N.; Kraetzschmar, T.; Kröninger, K.; Kumar, A.; Kuzminov, V. V.; Lang, K.; Laubenstein, M.; Lazzaro, A.; Li, Y. L.; Li, Y.-Y.; Li, H. B.; Lin, S. T.; Lindner, M.; Lippi, I.; Liu, S. K.; Liu, X.; Liu, J.; Loomba, D.; Lubashevskiy, A.; Lubsandorzhiev, B.; Lutter, G.; Ma, H.; Majorovits, B.; Mamedov, F.; Martin, R. D.; Massarczyk, R.; Matthews, J. A. J.; McFadden, N.; Mei, D.-M.; Mei, H.; Meijer, S. J.; Mengoni, D.; Mertens, S.; Miller, W.; Miloradovic, M.; Mingazheva, R.; Misiaszek, M.; Moseev, P.; Myslik, J.; Nemchenok, I.; Nilsson, T.; Nolan, P.; O'Shaughnessy, C.; Othman, G.; Panas, K.; Pandola, L.; Papp, L.; Pelczar, K.; Peterson, D.; Pettus, W.; Poon, A. W. P.; Povinec, P. P.; Pullia, A.; Quintana, X. C.; Radford, D. C.; Rager, J.; Ransom, C.; Recchia, F.; Reine, A. L.; Riboldi, S.; Rielage, K.; Rozov, S.; Rouf, N. W.; Rukhadze, E.; Rumyantseva, N.; Saakyan, R.; Sala, E.; Salamida, F.; Sandukovsky, V.; Savard, G.; Schönert, S.; Schütz, A.-K.; Schulz, O.; Schuster, M.; Schwingenheuer, B.; Selivanenko, O.; Sevda, B.; Shanks, B.; Shevchik, E.; Shirchenko, M.; Simkovic, F.; Singh, L.; Singh, V.; Skorokhvatov, M.; Smolek, K.; Smolnikov, A.; Sonay, A.; Spavorova, M.; Stekl, I.; Stukov, D.; Tedeschi, D.; Thompson, J.; Van Wechel, T.; Varner, R. L.; Vasenko, A. A.; Vasilyev, S.; Veresnikova, A.; Vetter, K.; von Sturm, K.; Vorren, K.; Wagner, M.; Wang, G.-J.; Waters, D.; Wei, W.-Z.; Wester, T.; White, B. R.; Wiesinger, C.; Wilkerson, J. F.; Willers, M.; Wiseman, C.; Wojcik, M.; Wong, H. T.; Wyenberg, J.; Xu, W.; Yakushev, E.; Yang, G.; Yu, C.-H.; Yue, Q.; Yumatov, V.; Zeman, J.; Zeng, Z.; Zhitnikov, I.; Zhu, B.; Zinatulina, D.; Zschocke, A.; Zsigmond, A. J.; Zuber, K.; Zuzel, G.

2017-10-01

The observation of neutrinoless double-beta decay (0νββ) would show that lepton number is violated, reveal that neu-trinos are Majorana particles, and provide information on neutrino mass. A discovery-capable experiment covering the inverted ordering region, with effective Majorana neutrino masses of 15 - 50 meV, will require a tonne-scale experiment with excellent energy resolution and extremely low backgrounds, at the level of ˜0.1 count /(FWHM.t.yr) in the region of the signal. The current generation 76Ge experiments GERDA and the Majorana Demonstrator, utilizing high purity Germanium detectors with an intrinsic energy resolution of 0.12%, have achieved the lowest backgrounds by over an order of magnitude in the 0νββ signal region of all 0νββ experiments. Building on this success, the LEGEND collaboration has been formed to pursue a tonne-scale 76Ge experiment. The collaboration aims to develop a phased 0νββ experimental program with discovery potential at a half-life approaching or at 1028 years, using existing resources as appropriate to expedite physics results.

A modeling of dynamic storage assignment for order picking in beverage warehousing with Drive-in Rack system

Science.gov (United States)

Hadi, M. Z.; Djatna, T.; Sugiarto

2018-04-01

This paper develops a dynamic storage assignment model to solve storage assignment problem (SAP) for beverages order picking in a drive-in rack warehousing system to determine the appropriate storage location and space for each beverage products dynamically so that the performance of the system can be improved. This study constructs a graph model to represent drive-in rack storage position then combine association rules mining, class-based storage policies and an arrangement rule algorithm to determine an appropriate storage location and arrangement of the product according to dynamic orders from customers. The performance of the proposed model is measured as rule adjacency accuracy, travel distance (for picking process) and probability a product become expiry using Last Come First Serve (LCFS) queue approach. Finally, the proposed model is implemented through computer simulation and compare the performance for different storage assignment methods as well. The result indicates that the proposed model outperforms other storage assignment methods.

Water Tank Experiments on Stratified Flow over Double Mountain-Shaped Obstacles at High-Reynolds Number

Directory of Open Access Journals (Sweden)

Ivana Stiperski

2017-01-01

Full Text Available In this article, we present an overview of the HyIV-CNRS-SecORo (Hydralab IV-CNRS-Secondary Orography and Rotors Experiments laboratory experiments carried out in the CNRM (Centre National de Recherches Météorologiques large stratified water flume. The experiments were designed to systematically study the influence of double obstacles on stably stratified flow. The experimental set-up consists of a two-layer flow in the water tank, with a lower neutral and an upper stable layer separated by a sharp density discontinuity. This type of layering over terrain is known to be conducive to a variety of possible responses in the atmosphere, from hydraulic jumps to lee waves and highly turbulent rotors. In each experiment, obstacles were towed through the tank at a constant speed. The towing speed and the size of the tank allowed high Reynolds-number flow similar to the atmosphere. Here, we present the experimental design, together with an overview of laboratory experiments conducted and their results. We develop a regime diagram for flow over single and double obstacles and examine the parameter space where the secondary obstacle has the largest influence on the flow. Trapped lee waves, rotors, hydraulic jumps, lee-wave interference and flushing of the valley atmosphere are successfully reproduced in the stratified water tank. Obstacle height and ridge separation distance are shown to control lee-wave interference. Results, however, differ partially from previous findings on the flow over double ridges reported in the literature due to the presence of nonlinearities and possible differences in the boundary layer structure. The secondary obstacle also influences the transition between different flow regimes and makes trapped lee waves possible for higher Froude numbers than expected for an isolated obstacle.

Results on neutrinoless double-β decay of 76Ge from phase I of the GERDA experiment.

Science.gov (United States)

Agostini, M; Allardt, M; Andreotti, E; Bakalyarov, A M; Balata, M; Barabanov, I; Barnabé Heider, M; Barros, N; Baudis, L; Bauer, C; Becerici-Schmidt, N; Bellotti, E; Belogurov, S; Belyaev, S T; Benato, G; Bettini, A; Bezrukov, L; Bode, T; Brudanin, V; Brugnera, R; Budjáš, D; Caldwell, A; Cattadori, C; Chernogorov, A; Cossavella, F; Demidova, E V; Domula, A; Egorov, V; Falkenstein, R; Ferella, A; Freund, K; Frodyma, N; Gangapshev, A; Garfagnini, A; Gotti, C; Grabmayr, P; Gurentsov, V; Gusev, K; Guthikonda, K K; Hampel, W; Hegai, A; Heisel, M; Hemmer, S; Heusser, G; Hofmann, W; Hult, M; Inzhechik, L V; Ioannucci, L; Janicskó Csáthy, J; Jochum, J; Junker, M; Kihm, T; Kirpichnikov, I V; Kirsch, A; Klimenko, A; Knöpfle, K T; Kochetov, O; Kornoukhov, V N; Kuzminov, V V; Laubenstein, M; Lazzaro, A; Lebedev, V I; Lehnert, B; Liao, H Y; Lindner, M; Lippi, I; Liu, X; Lubashevskiy, A; Lubsandorzhiev, B; Lutter, G; Macolino, C; Machado, A A; Majorovits, B; Maneschg, W; Misiaszek, M; Nemchenok, I; Nisi, S; O'Shaughnessy, C; Pandola, L; Pelczar, K; Pessina, G; Pullia, A; Riboldi, S; Rumyantseva, N; Sada, C; Salathe, M; Schmitt, C; Schreiner, J; Schulz, O; Schwingenheuer, B; Schönert, S; Shevchik, E; Shirchenko, M; Simgen, H; Smolnikov, A; Stanco, L; Strecker, H; Tarka, M; Ur, C A; Vasenko, A A; Volynets, O; von Sturm, K; Wagner, V; Walter, M; Wegmann, A; Wester, T; Wojcik, M; Yanovich, E; Zavarise, P; Zhitnikov, I; Zhukov, S V; Zinatulina, D; Zuber, K; Zuzel, G

2013-09-20

Neutrinoless double beta decay is a process that violates lepton number conservation. It is predicted to occur in extensions of the standard model of particle physics. This Letter reports the results from phase I of the Germanium Detector Array (GERDA) experiment at the Gran Sasso Laboratory (Italy) searching for neutrinoless double beta decay of the isotope (76)Ge. Data considered in the present analysis have been collected between November 2011 and May 2013 with a total exposure of 21.6 kg yr. A blind analysis is performed. The background index is about 1 × 10(-2) counts/(keV kg yr) after pulse shape discrimination. No signal is observed and a lower limit is derived for the half-life of neutrinoless double beta decay of (76)Ge, T(1/2)(0ν) >2.1 × 10(25) yr (90% C.L.). The combination with the results from the previous experiments with (76)Ge yields T(1/2)(0ν)>3.0 × 10(25) yr (90% C.L.).

The Rack-Gear Tool Generation Modelling. Non-Analytical Method Developed in CATIA, Using the Relative Generating Trajectories Method

Science.gov (United States)

Teodor, V. G.; Baroiu, N.; Susac, F.; Oancea, N.

2016-11-01

The modelling of a curl of surfaces associated with a pair of rolling centrodes, when it is known the profile of the rack-gear's teeth profile, by direct measuring, as a coordinate matrix, has as goal the determining of the generating quality for an imposed kinematics of the relative motion of tool regarding the blank. In this way, it is possible to determine the generating geometrical error, as a base of the total error. The generation modelling allows highlighting the potential errors of the generating tool, in order to correct its profile, previously to use the tool in machining process. A method developed in CATIA is proposed, based on a new method, namely the method of “relative generating trajectories”. They are presented the analytical foundation, as so as some application for knows models of rack-gear type tools used on Maag teething machines.

Semiconductor-based experiments for neutrinoless double beta decay search

International Nuclear Information System (INIS)

Barnabé Heider, Marik

2012-01-01

Three experiments are employing semiconductor detectors in the search for neutrinoless double beta (0νββ) decay: COBRA, Majorana and GERDA. COBRA is studying the prospects of using CdZnTe detectors in terms of achievable energy resolution and background suppression. These detectors contain several ββ emitters and the most promising for 0νββ-decay search is 116 Cd. Majorana and GERDA will use isotopically enriched high purity Ge detectors to search for 0νββ-decay of 76 Ge. Their aim is to achieve a background ⩽10 −3 counts/(kg⋅y⋅keV) at the Q improvement compared to the present state-of-art. Majorana will operate Ge detectors in electroformed-Cu vacuum cryostats. A first cryostat housing a natural-Ge detector array is currently under preparation. In contrast, GERDA is operating bare Ge detectors submerged in liquid argon. The construction of the GERDA experiment is completed and a commissioning run started in June 2010. A string of natural-Ge detectors is operated to test the complete experimental setup and to determine the background before submerging the detectors enriched in 76 Ge. An overview and a comparison of these three experiments will be presented together with the latest results and developments.

Tribology experiment. [journal bearings and liquid lubricants

Science.gov (United States)

Wall, W. A.

1981-01-01

A two-dimensional concept for Spacelab rack 7 was developed to study the interaction of liquid lubricants and surfaces under static and dynamic conditions in a low-gravity environment fluid wetting and spreading experiments of a journal bearing experiments, and means to accurately measure and record the low-gravity environment during experimentation are planned. The wetting and spreading process of selected commercial lubricants on representative surface are to the observes in a near-zero gravity environment.

A relay rack for a control and protection system for nuclear reactors

International Nuclear Information System (INIS)

Miyata, Yasuyuki; Oda, Noriaki; Akiyama, Toyoshi

1975-01-01

It is obvious that all the equipment in the various systems that constitute a nuclear power plant must exhibit the highest levels of reliability, but the reactor control and protection system is of vital importance, and thus it requires a particularly thorough approach, incorporating redundancy, independence and separation. The paper describes the functions, construction and specifications of the relay rack - one of the most important items of equipment for reactor control and protection in a generating facility using a pressurized-water reactor - and it gives details of the extent to which these three requirements are satisfied. (author)

Exposure of eyes to perfume: a double-blind, placebo-controlled experiment.

Science.gov (United States)

Elberling, J; Duus Johansen, J; Dirksen, A; Mosbech, H

2006-08-01

Environmental perfume exposure can elicit bothersome respiratory symptoms. Symptoms are induced at exposure levels which most people find tolerable, and the mechanisms are unclear. The aim of the study was to investigate patients with eye and respiratory symptoms related to environmental perfume, by exposing the eyes to perfume in a double-blind, placebo-controlled study.Twenty-one eczema patients with respiratory symptoms elicited by perfume were compared with 21 healthy volunteers in a sex- and age-matched case-control study. The participants completed a symptom questionnaire, and underwent a double-blind, placebo-controlled exposure to perfume. Of the 42 individuals tested, 10 had more eye symptoms (irritation, itching, and tears) during perfume exposure than during placebo exposures, and eight of these individuals (P = 0.07, Fisher's exact test) belonged to the patient group. A true positive eye reaction to perfume was significantly associated with identification of perfume as an active exposure (P perfume elicited irritation in the eyes independently of olfaction, but the relative importance of ocular chemoperception in relation to elicitation of respiratory symptoms from common environmental exposures to perfume remains unclear. We investigated the hypothesis of an association between respiratory symptoms related to perfume and ocular perfume sensitivity by exposing the eyes to perfume in a double blind, placebo-controlled experiment. Vapors of perfume provoked symptoms in the relevant eye in some patients and healthy control persons, but under our exposure conditions, ocular chemesthesis failed to elicit respiratory symptoms.

Central tracker for BM@N experiment based on double side Si-microstrip detectors

Science.gov (United States)

Kovalev, Yu.; Kapishin, M.; Khabarov, S.; Shafronovskaia, A.; Tarasov, O.; Makankin, A.; Zamiatin, N.; Zubarev, E.

2017-07-01

Design of central tracker system based on Double-Sided Silicon Detectors (DSSD) for BM@N experiment is described. A coordinate plane with 10240 measuring channels, pitch adapter, reading electronics was developed. Each element was tested and assembled into a coordinate plane. The first tests of the plane with 106Ru source were carried out before installation for the BM@N experiment. The results of the study indicate that noisy channels and inefficient channels are less than 3%. In general, single clusters 87% (one group per module of consecutive strips) and 75% of clusters with a width equal to one strip.

Standard specification for boron-Based neutron absorbing material systems for use in nuclear spent fuel storage racks

CERN Document Server

American Society for Testing and Materials. Philadelphia

2011-01-01

1.1 This specification defines criteria for boron-based neutron absorbing material systems used in racks in a pool environment for storage of nuclear light water reactor (LWR) spent-fuel assemblies or disassembled components to maintain sub-criticality in the storage rack system. 1.2 Boron-based neutron absorbing material systems normally consist of metallic boron or a chemical compound containing boron (for example, boron carbide, B4C) supported by a matrix of aluminum, steel, or other materials. 1.3 In a boron-based absorber, neutron absorption occurs primarily by the boron-10 isotope that is present in natural boron to the extent of 18.3 ± 0.2 % by weight (depending upon the geological origin of the boron). Boron, enriched in boron-10 could also be used. 1.4 The materials systems described herein shall be functional – that is always be capable to maintain a B10 areal density such that subcriticality Keff <0.95 or Keff <0.98 or Keff < 1.0 depending on the design specification for the service...

Quantum interactive learning tutorial on the double-slit experiment to improve student understanding of quantum mechanics

Science.gov (United States)

Sayer, Ryan; Maries, Alexandru; Singh, Chandralekha

2017-06-01

Learning quantum mechanics is challenging, even for upper-level undergraduate and graduate students. Research-validated interactive tutorials that build on students' prior knowledge can be useful tools to enhance student learning. We have been investigating student difficulties with quantum mechanics pertaining to the double-slit experiment in various situations that appear to be counterintuitive and contradict classical notions of particles and waves. For example, if we send single electrons through the slits, they may behave as a "wave" in part of the experiment and as a "particle" in another part of the same experiment. Here we discuss the development and evaluation of a research-validated Quantum Interactive Learning Tutorial (QuILT) which makes use of an interactive simulation to improve student understanding of the double-slit experiment and strives to help students develop a good grasp of foundational issues in quantum mechanics. We discuss common student difficulties identified during the development and evaluation of the QuILT and analyze the data from the pretest and post test administered to the upper-level undergraduate and first-year physics graduate students before and after they worked on the QuILT to assess its effectiveness. These data suggest that on average, the QuILT was effective in helping students develop a more robust understanding of foundational concepts in quantum mechanics that defy classical intuition using the context of the double-slit experiment. Moreover, upper-level undergraduates outperformed physics graduate students on the post test. One possible reason for this difference in performance may be the level of student engagement with the QuILT due to the grade incentive. In the undergraduate course, the post test was graded for correctness while in the graduate course, it was only graded for completeness.

Quantum interactive learning tutorial on the double-slit experiment to improve student understanding of quantum mechanics

Directory of Open Access Journals (Sweden)

Ryan Sayer

2017-05-01

Full Text Available Learning quantum mechanics is challenging, even for upper-level undergraduate and graduate students. Research-validated interactive tutorials that build on students’ prior knowledge can be useful tools to enhance student learning. We have been investigating student difficulties with quantum mechanics pertaining to the double-slit experiment in various situations that appear to be counterintuitive and contradict classical notions of particles and waves. For example, if we send single electrons through the slits, they may behave as a “wave” in part of the experiment and as a “particle” in another part of the same experiment. Here we discuss the development and evaluation of a research-validated Quantum Interactive Learning Tutorial (QuILT which makes use of an interactive simulation to improve student understanding of the double-slit experiment and strives to help students develop a good grasp of foundational issues in quantum mechanics. We discuss common student difficulties identified during the development and evaluation of the QuILT and analyze the data from the pretest and post test administered to the upper-level undergraduate and first-year physics graduate students before and after they worked on the QuILT to assess its effectiveness. These data suggest that on average, the QuILT was effective in helping students develop a more robust understanding of foundational concepts in quantum mechanics that defy classical intuition using the context of the double-slit experiment. Moreover, upper-level undergraduates outperformed physics graduate students on the post test. One possible reason for this difference in performance may be the level of student engagement with the QuILT due to the grade incentive. In the undergraduate course, the post test was graded for correctness while in the graduate course, it was only graded for completeness.

Search of Neutrinoless Double Beta Decay with the GERDA Experiment

Science.gov (United States)

Agostini, M.; Allardt, M.; Bakalyarov, A. M.; Balata, M.; Barabanov, I.; Baudis, L.; Bauer, C.; Becerici-Schmidt, N.; Bellotti, E.; Belogurov, S.; Belyaev, S. T.; Benato, G.; Bettini, A.; Bezrukov, L.; Bode, T.; Borowicz, D.; Brudanin, V.; Brugnera, R.; Budjáš, D.; Caldwell, A.; Cattadori, C.; Chernogorov, A.; D'Andrea, V.; Demidova, E. V.; Domula, A.; Doroshkevich, E.; Egorov, V.; Falkenstein, R.; Fedorova, O.; Freund, K.; Frodyma, N.; Gangapshev, A.; Garfagnini, A.; Gooch, C.; Gotti, C.; Grabmayr, P.; Gurentsov, V.; Gusev, K.; Hampel, W.; Hegai, A.; Heisel, M.; Hemmer, S.; Heusser, G.; Hoffmann, W.; Hult, M.; Inzhechik, L. V.; Ioannucci, L.; Janicksó Csáthy, J.; Jochum, J.; Junker, M.; Kazalov, V.; Kihm, T.; Kirpichnikov, I. V.; Kirsch, A.; Klimenko, A.; Knöpfle, K. T.; Kochetov, O.; Kornoukhov, V. N.; Kuzminov, V. V.; Laubenstein, M.; Lazzaro, A.; Lebedev, V. I.; Lehnert, B.; Liao, H. Y.; Lindner, M.; Lippi, I.; Lubashevskiy, A.; Lubsandorzhiev, B.; Lutter, G.; Macolino, C.; Majorovits, B.; Maneschg, W.; Marissens, G.; Medinaceli, E.; Misiaszek, M.; Moseev, P.; Nemchenok, I.; Nisi, S.; Palioselitis, D.; Panas, K.; Pandola, L.; Pelczar, K.; Pessina, G.; Pullia, A.; Reissfelder, M.; Riboldi, S.; Rumyantseva, N.; Sada, C.; Salathe, M.; Schmitt, C.; Schneider, B.; Schreiner, J.; Schulz, O.; Schwingenheuer, B.; Schönert, S.; Seitz, H.; Selivalenko, O.; Shevchik, E.; Shirchenko, M.; Simgen, H.; Smolnikov, A.; Stanco, L.; Stepaniuk, M.; Strecker, H.; Ur, C. A.; Vanhoefer, L.; Vasenko, A. A.; Veresnikova, A.; von Sturm, K.; Wagner, V.; Walter, M.; Wegmann, A.; Wester, T.; Wiesinger, C.; Wilsenach, H.; Wojcik, M.; Yanovich, E.; Zavarise, P.; Zhitnikov, I.; Zhukov, S. V.; Zinatulina, D.; Zuber, K.; Zuzel, G.

2016-04-01

The GERDA (GERmanium Detector Array) is an experiment for the search of neutrinoless double beta decay (0 νββ) in 76Ge, located at Laboratori Nazionali del Gran Sasso of INFN (Italy). In the first phase of the experiment, a 90% confidence level (C.L.) sensitivity of 2.4 ṡ1025 yr on the 0 νββ decay half-life was achieved with a 21.6 kgṡyr exposure and an unprecedented background index in the region of interest of 10-2 counts/(keVṡkgṡyr). No excess of signal events was found, and an experimental lower limit on the half-life of 2.1 ṡ 1025 yr (90% C.L.) was established. Correspondingly, the limit on the effective Majorana neutrino mass is mee < 0.2- 0.4 eV, depending on the considered nuclear matrix element. The previous claim for evidence of a 0 νββ decay signal is strongly disfavored, and the field of research is open again.

Background constrains of the SuperNEMO experiment for neutrinoless double beta-decay searches

Energy Technology Data Exchange (ETDEWEB)

Povinec, Pavel P.

2017-02-11

The SuperNEMO experiment is a new generation of experiments dedicated to the search for neutrinoless double beta-decay, which if observed, would confirm the existence of physics beyond the Standard Model. It is based on the tracking and calorimetry techniques, which allow the reconstruction of the final state topology, including timing and kinematics of the double beta-decay transition events, offering a powerful tool for background rejection. While the basic detection strategy of the SuperNEMO detector remains the same as of the NEMO-3 detector, a number of improvements were accomplished for each of detector main components. Upgrades of the detector technologies and development of low-level counting techniques ensure radiopurity control of construction parts of the SuperNEMO detector. A reference material made of glass pellets has been developed to assure quality management and quality control of radiopurity measurements. The first module of the SuperNEMO detector (Demonstrator) is currently under construction in the Modane underground laboratory. No background event is expected in the neutrinoless double beta-decay region in 2.5 years of its operation using 7 kg of {sup 82}Se. The half-life sensitivity of the Demonstrator is expected to be >6.5·10{sup 24} y, corresponding to an effective Majorana neutrino mass sensitivity of |0.2−0.4| eV (90% C.L.). The full SuperNEMO experiment comprising of 20 modules with 100 kg of {sup 82}Se source should reach an effective Majorana neutrino mass sensitivity of |0.04−0.1| eV, and a half-life limit 1·10{sup 26} y. - Highlights: • SuperNEMO detector for 2β0ν-decay of {sup 82}Se should reach half-life limit of 10{sup 26} y. • Radiopurity of the SuperNEMO internal detector parts was checked down to 0.1 mBq/kg. • Reference material of glass pellets was developed for underground γ-spectrometry.

Materials Science Research Rack Onboard the International Space Station

Science.gov (United States)

Reagan, Shawn; Frazier, Natalie; Lehman, John

2016-01-01

The Materials Science Research Rack (MSRR) is a research facility developed under a cooperative research agreement between NASA and ESA for materials science investigations on the International Space Station (ISS). MSRR was launched on STS-128 in August 2009 and currently resides in the U.S. Destiny Laboratory Module. Since that time, MSRR has logged more than 1400 hours of operating time. The MSRR accommodates advanced investigations in the microgravity environment on the ISS for basic materials science research in areas such as solidification of metals and alloys. The purpose is to advance the scientific understanding of materials processing as affected by microgravity and to gain insight into the physical behavior of materials processing. MSRR allows for the study of a variety of materials, including metals, ceramics, semiconductor crystals, and glasses. Materials science research benefits from the microgravity environment of space, where the researcher can better isolate chemical and thermal properties of materials from the effects of gravity. With this knowledge, reliable predictions can be made about the conditions required on Earth to achieve improved materials. MSRR is a highly automated facility with a modular design capable of supporting multiple types of investigations. The NASA-provided Rack Support Subsystem provides services (power, thermal control, vacuum access, and command and data handling) to the ESA-developed Materials Science Laboratory (MSL) that accommodates interchangeable Furnace Inserts (FI). Two ESA-developed FIs are presently available on the ISS: the Low Gradient Furnace (LGF) and the Solidification and Quenching Furnace (SQF). Sample Cartridge Assemblies (SCAs), each containing one or more material samples, are installed in the FI by the crew and can be processed at temperatures up to 1400?C. ESA continues to develop samples with 14 planned for launch and processing in the near future. Additionally NASA has begun developing SCAs to

Acoustic Noise Prediction of the Amine Swingbed ISS ExPRESS Rack Payload

Science.gov (United States)

Welsh, David; Smith, Holly; Wang, Shuo

2010-01-01

Acoustics plays a vital role in maintaining the health, safety, and comfort of crew members aboard the International Space Station (ISS). In order to maintain this livable and workable environment, acoustic requirements have been established to ensure that ISS hardware and payload developers account for the acoustic emissions of their equipment and develop acoustic mitigations as necessary. These requirements are verified by an acoustic emissions test of the integrated hardware. The Amine Swingbed ExPRESS (Expedite the PRocessing of ExperimentS to Space) rack payload creates a unique challenge to the developers in that the payload hardware is transported to the ISS in phases, making an acoustic emissions test on the integrated flight hardware impossible. In addition, the payload incorporates a high back pressure fan and a diaphragm vacuum pump, which are recognized as significant and complex noise sources. In order to accurately predict the acoustic emissions of the integrated payload, the individual acoustic noise sources and paths are first characterized. These characterizations are conducted though a series of acoustic emissions tests on the individual payload components. Secondly, the individual acoustic noise sources and paths are incorporated into a virtual model of the integrated hardware. The virtual model is constructed with the use of hybrid method utilizing the Finite Element Acoustic (FEA) and Statistical Energy Analysis (SEA) techniques, which predict the overall acoustic emissions. Finally, the acoustic model is validated though an acoustic characterization test performed on an acoustically similar mock-up of the flight unit. The results of the validated acoustic model are then used to assess the acoustic emissions of the flight unit and define further acoustic mitigation efforts.

Inner conductor of the magnetic double-horn for the neutrino oscillation experiment with BEBC

CERN Multimedia

CERN PhotoLab

1982-01-01

In 1980 renewed interest arose in probing for neutrino non-zero masses and associated neutrino oscillations. Low-energy muon-neutrino beams (produced with a proton beam from the PS) were directed towards the SPS neutrino detectors, BEBC, WA1 and WA18 (Annual Report 1982, p.43, Fig.13). Experiments PS169 (WA1) and PS181 (WA18) were "disappearence" experiments and used a "bare" production target, whereas experiment PS180 (BEBC), looked for electron-neutrino "appearence" and used a horn-focused beam. The manufacture of the inner conductor of the double-horn (a particular breed of current-sheet lens) required exceedingly delicate machining. For further pictures see 8304055 and Annual Report 1982, p.137; and p.43 for a description of the experiments.

The Milano-Gran Sasso double beta decay experiment: toward a 20-crystal array

International Nuclear Information System (INIS)

Alessandrello, A.; Brofferio, C.; Bucci, C.; Cremonesi, O.; Fiorini, E.; Giuliani, A.; Nucciotti, A.; Pavan, M.; Pessina, G.; Previtali, E.; Zanotti, L.

1996-01-01

TeO 2 thermal detectors are being used by the Milano group to search for neutrinoless double beta decay of 130 Te. An upper limit for neutrinoless decay half life of 2.1 x 10 22 yr at 90% CL obtained with a 334 g TeO 2 detector has been previously reported. To improve the sensitivity of the experiment an array of twenty 340 g TeO 2 crystals will be realised in the next future. As a first step toward the realisation of that experiment a 4 crystal detector has been tested in the Gran Sasso refrigerator. Detector performances, data acquisition and analysis are discussed. (orig.)

Smart Rack Monitor for the Linac control system

International Nuclear Information System (INIS)

Shtirbu, S.; Goodwin, R.W.; McCrory, E.S.; Shea, M.F.

1991-01-01

The Smart Rack Monitor (SRM) is a low-cost, one board, data-acquisition module for the upgraded Linac control system at Fermilab. The SRM is based on the Motorola MC68332 microcontroller in the Business Card Computer (BCC) configuration. It is connected to the Linac local control station (to be referred to as Local Station) by an Arcnet LAN, and can be located close to the controlled hardware. Each Local Station is connected to several SRMs. The SRM has 64 A-D channels, sixteen D-A channels, and eight bytes of digital I/O on the mother board. Software Components Group's pSOS is the SRM's kernel. The SRM's software is cross-developed on VAX/VMS in C. The SRM does not have an attached console and is fully controlled by the Local Station. It performs data acquisition and settings, as directed by the Local Station. Its existence is transparent to the rest of the control system. The SRM supports code updates downloading from the VAX, through the Local Station

Arabidopsis scaffold protein RACK1A modulates rare sugar D-allose regulated gibberellin signaling

OpenAIRE

Fennell, Herman; Olawin, Abdulquadri; Mizanur, Rahman M.; Izumori, Ken; Chen, Jin-Gui; Ullah, Hemayet

2012-01-01

As energy sources and structural components, sugars are the central regulators of plant growth and development. In addition to the abundant natural sugars in plants, more than 50 different kinds of rare sugars exist in nature, several of which show distinct roles in plant growth and development. Recently, one of the rare sugars, D-allose, an epimer of D-glucose at C3, is found to suppress plant hormone gibberellin (GA) signaling in rice. Scaffold protein RACK1A in the model plant Arabidopsis ...

Comment on 'Biphoton double-slit experiment'

International Nuclear Information System (INIS)

Oriols, X.

2005-01-01

In a recent paper [Phys. Rev. A 68, 033803 (2003)] experimental results on a double-slit configuration with two entangled bosons are presented. The authors argue that their data contradicts the de Broglie-Bohm interpretation of quantum mechanics. In this Comment we show that this conclusion is incorrect

Virtual planning of dental implant placement using CT double scan-technique - own experience

International Nuclear Information System (INIS)

Wojciechowski, W.; Urbanik, A.; Kownacki, P.; Kownacki, S.

2007-01-01

The correctness of CT performed with the use of a double-scan technique is the basis for achieving proper quality of 3D reconstructions of the maxilla or mandible and subsequent virtual planning of dental implant placement. The aim of this study was the presentation of the methodology of computed tomography scanning and own experience with the use of the double-scan technique. The study group included 26 individuals who underwent MDCT with a double-scan technique using a MDCT scanner SOMATOM Sensation (Siemens, Germany). The parameters of the examination: slice-collimation 10 x 0.75 mm, slice-thickness 0.75 mm. The first CT scan in the procedure was the scan of the patient wearing a radiological prosthesis and occlusal index, which was followed by a separate scan of the radiological prosthesis. These two CT scans were copied and transferred to PC with Procera Software program (Nobel Biocare, Sweden) where dental implant placement was virtually planned. In all 26 patients, precise three-dimensional reconstructions of the anatomical structure were obtained. In 11 patients, on the basis of the virtual planning, the implant placement was performed, 5 patients were referred to preparatory procedures, that is, restoration of the alveolar process, otolaryngological treatment of the maxillary sinuses. The remaining 10 patients did not qualify to the procedure because of unfavorable anatomical ideation's. Correct computed tomography with double-scan technique enables virtual planning of dental implant placement, on the basis of which the real procedure of implantation can be performed. (author)

Experiment and simulation of double-layered RC plates under impact loadings. Part 1: Impact tests for double-layered RC plates

International Nuclear Information System (INIS)

Shirai, T.; Ueda, M.; Taniguchi, H.; Kambayashi, A.; Ohno, T.; Ishikawa, N.

1993-01-01

At a nuclear power plant facility, it should be of interest and important problem to ensure structures against impact loads induced by projectile impacts or plant-internal accidents. It has been well known that local damage consists of spalling of concrete from the impacted area and scabbing of concrete from the back face of the target together with projectile penetration into the target. There are several techniques for improving the impact resistance of RC slabs, that is, lining with a steel plate on the impacted and/or rear face of the slab, making the slab a double-layered composite slab with an elastic absorber and employing a fiber reinforced concrete or a high-strength concrete as the slab materials. Of the many measures available for withstanding impact loads, the use of a double-layered reinforced concrete (RC) slab with absorber is expected to have the higher resistance in reducing or preventing local damage. This paper presents the results of an experimental investigation on the impact resistance of double-layered RC plates subjected to the impact of projectile. In the experiment, the effects of two parameters; the combination of two RC plates having different thicknesses and the existence of an absorber in the middle layer, are mainly investigated. And, the effects of the concrete thickness (7,9 and 11 cm) and the concrete strength (a normal-:35MPa, a lightweight-:40MPa and a high-strength:57MPa) of target were also examined. RC plates, 0.6m-square, were used for test specimens. The projectile has a mass of 0.43kg, made of steel with a flat nose. An average projectile velocity was about 170m/sec. A rubber plate shaped into a square with the same size of RC plate was used for a double-layered specimen as an absorber which was put between two RC plates. It could be concluded that double-layering and presence of an absorber had a considerable effect on the increase of impact resistance of RC plate. In order to reduce local damage, it is more effective to

Pemodelan Matematik Kinerja Pengering Surya Efek Rumah Kaca (ERK-Hibrid Menggunakan Rak Berputar secara Vertikal (Mathematical Modeling Performance of Greenhouse Effect (GHE-Hybrid Solar Dryer with a Vertical Rotating Rack

Directory of Open Access Journals (Sweden)

Sigit Triwahyudi

2016-12-01

Full Text Available This paper presents a performance test and mathematical modeling of greenhouse effect (GHE-Hybrid solar dryer with vertical rotating rack. The dryer consists of a greenhouse dryer (1100 × 860 × 1300 mm with eight rack and additional heating system consists of a flat plate collector (1,04 m2, a hot water storage tank (197 liters and a heat exchanger. To investigate the performance of solar greenhouse dryer, five experimental variation speed of rack were conducted (1, 4, 7, 10 rpm and without rotation. Materials used in the experiment are local cardamom (Amomum cardamomum Wild. Weight of each experiment  about  9 to 10 kg. The average temperature of the hot water storage tank varies from 50.0 to 55.0 °C, drying air  temperature between 38.9 to 45.9 °C, while the relative humidity (RH of drying chamber ranged from 32.1 to 47.4 %. Variation of rotational speed affects on the uniformity of product temperature and water content in each rack drying. At rotation 1 rpm  (experiment II, obtained  as the best conditions (temperature and moisture content are most uniform. Increasing rotational speed of rack causes increasing in standard deviation of  product temperature and moisture content. To simulate the performance of the dryer, mathematical modeling based on heat  and mass transfer and a thin layer drying  approaches were conducted. Equations solved numerically using the finite difference Euler with Visual Basic Application (VBA program on Excel. Validation was conducted by comparing the calculation results of mathematical modeling (data prediction with measurement data (data observation. Criterion validity was determined by  the value of the coefficient of determination (R2, the value of RMSD and MAPD. Mathematical models that have been developed can be described precisely the temperature of the hot water storage tank, temperature of the drying chamber, temperature of the product as well as a moisture content decrease.   ABSTRAK Makalah

Double layers in space

International Nuclear Information System (INIS)

Carlqvist, P.

1982-07-01

For more than a decade it has been realised that electrostatic double layers are likely to occur in space. We briefly discuss the theoretical background of such double layers. Most of the paper is devoted to an account of the observational evidence for double layers in the ionosphere and magnetosphere of the Earth. Several different experiments are reviewed including rocket and satellite measurements and ground based observations. It is concluded that the observational evidence for double layers in space is very strong. The experimental results indicate that double layers with widely different properties may exist in space. (Author)

Double layers in space

International Nuclear Information System (INIS)

Carlqvist, P.

1982-01-01

For more than a decade it has been realised that electrostatic double layers are likely to occur in space. The author briefly discusses the theoretical background of such double layers. Most of the paper is devoted to an account of the observational evidence for double layers in the ionosphere and magnetosphere of the Earth. Several different experiments are reviewed including rocket and satellite measurements and ground based observations. It is concluded that the observational evidence for double layers in space is very strong. The experimental results indicate that double layers with widely different properties may exist in space. (Auth.)

Redesign of the spent fuel storage racks at the Trojan Nuclear Plant

International Nuclear Information System (INIS)

Stump, K.

1987-01-01

The spent fuel pool (SFP) at the Trojan Nuclear Plant located near Prescott, Oregon, was originally designed to hold 1.33 cores worth of spent fuel assemblies. Due to the delay in the site selection and preparation process for the spent fuel repository, the SFP storage capacity was increased in 1978 from 260 assemblies to 651 assemblies and in 1983 was increased again from 651 to 1408 assemblies to allow Trojan to continue operations through the year 2003 with a full core reserve in the SFP. Now it appears unlikely that a high level waste repository will be in operation before 2010. This indicates that a further capacity increase in the SFP is required to allow commercial operation until 2010, at which time the repository should be open to receive spent fuel. To accomplish this, an increase of seven times the original SFP capacity of 260 assemblies is needed. This paper presents a spent fuel assembly rack design that enables the required capacity increase in the SFP to be met. By the use of a boron carbide - silicon polymer inside a titanium/vanadium honeycomb as a neutron absorber between the fuel assemblies and by increasing the metal to water ratio of the spent fuel pool to harden the neutron energy spectrum the capacity of the SFP is increased to 1880 assemblies for an increase of 7.23 times the original spent fuel pool capacity. The multiplication factor for the pool with every fuel assembly slot filled in the new rack system is 0.62; well below the NRC regulatory limit of keff < 0.95. The capacity increase with allow the commercial operation of the Trojan Nuclear Plant through 2010 with a full core reserve in the spent fuel pool

Quantum Interactive Learning Tutorial on the Double-Slit Experiment to Improve Student Understanding of Quantum Mechanics

Science.gov (United States)

Sayer, Ryan; Maries, Alexandru; Singh, Chandralekha

2017-01-01

Learning quantum mechanics is challenging, even for upper-level undergraduate and graduate students. Research-validated interactive tutorials that build on students' prior knowledge can be useful tools to enhance student learning. We have been investigating student difficulties with quantum mechanics pertaining to the double-slit experiment in…

Double slit experiment with quantum detectors: mysteries, meanings, misinterpretations and measurement

Science.gov (United States)

Rameez-ul-Islam; Ikram, Manzoor; Hasan Mujtaba, Abid; Abbas, Tasawar

2018-01-01

We propose an idea for symmetric measurements through the famous double slit experiment (DSE) in a new detection scenario. The interferometric setup is complemented here with quantum detectors that switch to an arbitrary superposition after interaction with the arms of the DSE. The envisioned schematics cover the full measurement range, i.e. from the weak to the strong projective situation with selectivity being a smoothly tunable open option, and suggests an alternative methodology for weak measurements based on information overlap from DSE paths. The results, though generally in agreement with the quantum paradigm, raise many questions over the nature of probabilities, the absurdity of the common language for phenomena’s description in the theory and the boundary separating the projective/non-projective measurements, and the related misconceived interpretations. Further, the results impose certain constraints over the hidden variable theories as well as on the repercussions of the weak measurements. Although described as a thought experiment, the proposal can equally be implemented experimentally under a prevailing research scenario.

Single-center experience in double kidney transplantation.

Science.gov (United States)

Fontana, I; Magoni Rossi, A; Gasloli, G; Santori, G; Giannone, A; Bertocchi, M; Piaggio, F; Bocci, E; Valente, Umberto

2010-05-01

Use of organs from marginal donors for transplantation is a current strategy to expand the organ donor pool. Its efficacy is universally accepted among data from multicenter studies. Herein, we have reviewed outcomes of double kidney transplantation (DKT) over an 9-year experience in our center. The aim of this study was to evaluate possible important differences between a monocenter versus multicenter studies. Between 1999 and 2008, we performed 59 DKT. Recipient mean age was 63 +/- 5 years. Mean HLA-A, -B, and -DR mismatches were 3.69 +/- 0.922. Donor mean age was 69 +/- 7 years and mean creatinine clearance was 69.8 +/- 30.8 mL/min. Proteinuria was detected in three donors (5%). Mean cold ischemia and warm ischemia times were 1130 +/- 216 and 48 +/- 11 minutes, respectively. The right and left kidney scores were 4.18 +/- 2 and 4.21 +/- 2, respectively. Thirty patients (51%) displayed good postoperative renal function; 22 (37%), acute tubular necrosis with postoperative dialysis; 3 (5%), acute rejection episodes; 4 (7%), single-graft transplantectomy due to vascular thrombosis; 1 (2%), a retransplantation; 5 (8%), a lymphocele; 3 (5%) vescicoureteral reflux or stenosis requiring surgical correction. Cytomegalovirus infection was detected in five patients (8%). In three patients (5%) displayed de novo neoplasia. Three patients showed chronic rejection (5%), whereas we observed a cyclosporine-related toxicity in 7 (12%). Nine patients (15%) developed iatrogenic diabetes. Patient and graft survivals after 3 years from DKT were 93% and 86.3%, respectively. In this study, we applied successfully a widespread score to allocate organs to single kidney transplantation or DKT. In our experience, the score is suitable for the organ allocation but it may be overprotective, excluding potentially suitable organs for a single transplantation. Copyright (c) 2010 Elsevier Inc. All rights reserved.

Thermal Evaluation of Storage Rack with an Advanced Neutron Absorber during Normal Operation

Energy Technology Data Exchange (ETDEWEB)

Lee, Hee-Jae; Kim, Mi-Jin; Sohn, Dong-Seong [UNIST, Ulsan (Korea, Republic of)

2016-10-15

The storage capacity of the domestic wet storage site is expected to reach saturation from Hanbit in 2024 to Sin-wolseong in 2038 and accordingly management alternatives are urgently taken. Since installation of the dense rack is considered in the short term, it is necessary to urgently develop an advanced neutron absorber which can be applied to a spent nuclear fuel storage facility. Neutron absorber is the material for controlling the reactivity. A material which has excellent thermal neutron absorption ability, high strength and corrosion resistance must be selected as the neutron absorber. Existing neutron absorbers are made of boron which has a good thermal absorption ability such as BORAL and METAMIC. However, possible problems have been reported in using the boron-based neutron absorber for wet storage facility. Gadolinium is known to have higher neutron absorption cross-section than that of boron. And the strength of duplex stainless steel is about 1.5 times higher than stainless steel 304 which has been frequently used as a structural material. Therefore, duplex stainless steel which contains gadolinium is in consideration as an advanced neutron absorber. Temperature distribution is shown in figure 4. In pool bottom region near the inlet shows a relatively low tendency and heat generated from the fuel assemblies is transmitted to the pool upper region by the vertical flow. Also, temperature gradient appear in rack structures for the axial direction and temperature is uniformly distributed in the pool upper region. Table 1 presents the calculated results. The maximum temperature is 306.63K and does not exceed the 333.15K (60℃). The maximum temperature of the neutron absorber is 306.48K.

Materials Science Research Rack Onboard the International Space Station Hardware and Operations

Science.gov (United States)

Lehman, John R.; Frazier, Natalie C.; Johnson, Jimmie

2012-01-01

The Materials Science Research Rack (MSRR) is a research facility developed under a cooperative research agreement between NASA and ESA for materials science investigations on the International Space Station (ISS). MSRR was launched on STS-128 in August 2009, and is currently installed in the U.S. Destiny Laboratory Module. Since that time, MSRR has performed virtually flawlessly, logging more than 620 hours of operating time. The MSRR accommodates advanced investigations in the microgravity environment on the ISS for basic materials science research in areas such as solidification of metals and alloys. The purpose is to advance the scientific understanding of materials processing as affected by microgravity and to gain insight into the physical behavior of materials processing. MSRR allows for the study of a variety of materials including metals, ceramics, semiconductor crystals, and glasses. Materials science research benefits from the microgravity environment of space, where the researcher can better isolate chemical and thermal properties of materials from the effects of gravity. With this knowledge, reliable predictions can be made about the conditions required on Earth to achieve improved materials. MSRR is a highly automated facility with a modular design capable of supporting multiple types of investigations. Currently the NASA-provided Rack Support Subsystem provides services (power, thermal control, vacuum access, and command and data handling) to the ESA developed Materials Science Laboratory (MSL) which accommodates interchangeable Furnace Inserts (FI). Two ESA-developed FIs are presently available on the ISS: the Low Gradient Furnace (LGF) and the Solidification and Quenching Furnace (SQF). Sample-Cartridge Assemblies (SCAs), each containing one or more material samples, are installed in the FI by the crew and can be processed at temperatures up to 1400 C. Once an SCA is installed, the experiment can be run by automatic command or science conducted via

Spatial Rack Drives Pitch Configurations: Essence and Content

Science.gov (United States)

Abadjieva, Emilia; Abadjiev, Valentin; Naganawa, Akihiro

2018-03-01

The practical realization of all types of mechanical motions converters is preceded by solving the task of their kinematic synthesis. In this way, the determination of the optimal values of the constant geometrical parameters of the chosen structure of the created mechanical system is achieved. The searched result is a guarantee of the preliminary defined kinematic characteristics of the synthesized transmission and in the first place, to guarantee the law of motions transformation. The kinematic synthesis of mechanical transmissions is based on adequate mathematical modelling of the process of motions transformation and on the object, realizing this transformation. Basic primitives of the mathematical models for synthesis upon a pitch contact point are geometric and kinematic pitch configurations. Their dimensions and mutual position in space are the input parameters for the processes of design and elaboration of the synthesized mechanical device. The study presented here is a brief review of the theory of pitch configurations. It is an independent scientific branch of the spatial gearing theory (theory of hyperboloid gears). On this basis, the essence and content of the corresponding primitives, applicable to the synthesis of spatial rack drives, are defined.

Operational experience with double acting piston pumps for cryogenic helium and nitrogen

International Nuclear Information System (INIS)

Vosswinkel, F.

1978-01-01

The design of a high efficiency double acting piston pump suitable for pumping liquefied gases at cryogenic temperatures for cable cooling, is reported. The pump has proved flexible, reliable and efficient in operation. The plunger-type pumps can be used for filling cryostats or dewars with liquid helium or nitrogen from a pressure free or pressurized storage vessel, or as circulators for subcooled, saturated and/or supercritical helium in large scale cooling experiments. Flow rates of up to 17 g/s, maximum operating pressure of 600 kPa absolute and maximum differential pressure of approximately 100 kPa are obtained. (UK)

Case study of feedbacks and synergisms in a double CO2 experiment

International Nuclear Information System (INIS)

Mitchell, C.S.; Potter, G.L.; Ellsaesser, H.W.; Walton, J.J.

1981-01-01

A method is described for analyzing the feedback and synergistic comtributions of temperature water vapor, cloud cover, surface albedo and CO 2 to the change in the radiation balance at the top of the atmosphere due to a perturbation in an annual-averaged zonal atmospheric climate model. The method is illustrated through analysis of a double CO 2 experiment with the Lawrence Livermore National Laboratory Statistical Dynamical Model (LLNL SDM). The method provides insight into the sensitivity of the model to feedback changes in individual parameters and how each parameter influences the effects of the others

A scintillating bolometer array for double beta decay studies: The LUCIFER experiment

Energy Technology Data Exchange (ETDEWEB)

Gironi, L., E-mail: luca.gironi@mib.infn.it [Università degli Studi di Milano-Bicocca, Milano (Italy); INFN – Sezione di Milano-Bicocca, Milano (Italy)

2016-07-11

The main goal of the LUCIFER experiment is to study the neutrinoless double beta decay, a rare process allowed if neutrinos are Majorana particles. Although aiming at a discovery, in the case of insufficient sensitivity the LUCIFER technique will be the demonstrator for a higher mass experiment able to probe the entire inverted hierarchy region of the neutrino mass. In order to achieve this challenging result, high resolution detectors with active background discrimination capability are required. This very interesting possibility can be largely fulfilled by scintillating bolometers thanks to the simultaneous read-out of heat and light emitted by the interactions in the detector or by pulse shape analysis. - Highlights: • The LUCIFER technique will be the demonstrator for a higher mass experiment. • Scintillating bolometers allow high energy resolution and background discrimination. • The first choice for the LUCIFER tower are ZnSe crystals. • The LUCIFER setup will consist of an array of 30 individual single module detectors. • An array of ZnMoO4 crystals allowed the bolometric observation of the 2vDBD of {sup 100}Mo.

Installation, commissioning and performance of the trigger system of the Double Chooz experiment and the analysis of hydrogen capture neutrino events

Energy Technology Data Exchange (ETDEWEB)

Lucht, Sebastian

2013-11-18

The Double Chooz experiment is a reactor antineutrino experiment located at Chooz, a small town in the Ardennes region in the north of France close to the Belgium border. The aim of the experiment is to measure the leptonic mixing angle θ{sub 13}. The antineutrino flux is measured by two identical detectors at different distances from the reactor cores used as neutrino source, in a so called ''disappearance'' experiment. Double Chooz is a precision experiment because previous experiments indicated a small value of θ{sub 13}. Therefore, the systematic uncertainties introduced by background events and detector related components have to be as small as possible. The detector and all electronic components have been designed accordingly. The first part of this thesis describes the trigger and timing system of the Double Chooz experiment. This system triggers the data acquisition of the detector. It continuously monitors the signals of the photomultiplier tubes (PMTs) of the detector. These signals are summed for groups of PMTs (group signal) and for all PMTs (sum signal). The group signals are the input signals to the trigger system. They are discriminated by one threshold resulting in a multiplicity condition on the number of active group signal discriminators. The sum signal is discriminated by four thresholds. The default trigger configuration for the Double Chooz experiment is based on a combination on the sum signal discriminators and the multiplicity condition. In addition, the trigger system provides a common clock signal for all data acquisition components and an online event classification to allow an online data reduction. The trigger system was installed and commissioned in 2011. In this thesis the commissioning of the trigger system and its performance is presented. Furthermore the development and tests of possible improvements for the trigger system are presented and discussed. The second part of this thesis introduces a complementary

Pulse-shape discrimination techniques for the COBRA double beta-decay experiment at LNGS

Science.gov (United States)

Zatschler, S.; COBRA Collaboration

2017-09-01

In modern elementary particle physics several questions arise from the fact that neutrino oscillation experiments have found neutrinos to be massive. Among them is the so far unknown nature of neutrinos: either they act as so-called Majorana particles, where one cannot distinguish between particle and antiparticle, or they are Dirac particles like all the other fermions in the Standard Model. The study of neutrinoless double beta-decay (0νββ-decay), where the lepton number conservation is violated by two units, could answer the question regarding the underlying nature of neutrinos and might also shed light on the mechanism responsible for the mass generation. So far there is no experimental evidence for the existence of 0νββ-decay, hence, existing experiments have to be improved and novel techniques should be explored. One of the next-generation experiments dedicated to the search for this ultra-rare decay is the COBRA experiment. This article gives an overview of techniques to identify and reject background based on pulse-shape discrimination.

STS-55 MS1/PLC Ross and Payload Specialist Walter work in SL-D2 module

Science.gov (United States)

1993-01-01

STS-55 Mission Specialist 1 (MS1) and Payload Commander (PLC) Jerry L. Ross floats near cycle ergometer and Rack 9 Anthrorack (AR) (Human Physiology Laboratory) as German Payload Specialist 1 Ulrich Walter reviews a checklist in front of Rack 11 Experiment Rack. These experiment stations and the crewmembers are in the shirt-sleeve environment of the Spacelab Deutsche 2 (SL-D2) science module onboard the Earth-orbiting Columbia, Orbiter Vehicle (OV) 102. In the background is the SL-D2 aft end cone. Behind Ross and Walter is Rack 12 Experiment Rack with Baroreflex (BA).

Method of making a rack for the storage of spent nuclear fuel

International Nuclear Information System (INIS)

Machado, O.J.; Moore, J.T.; Cooney, B.F.

1990-01-01

This paper discusses a method of making a rack for storing nuclear fuel. It comprises bending each of the sheets into a sheet structure of configuration of angular transverse cross section, positioning each sheet structure with its longitudinal edges abutting the longitudinal edges of another of the sheet structures, metallurgically joining the abutting edges of the pair of sheet structures whose edges are abutting to form bodies of transverse rectangular cross section, mounting the bodies on a baseplate adjacent to each other with each longitudinal corner of each body face-to-face with a longitudinal corner of each adjacent body, metallurgically joining directly each corner of the each body to each facing corner of each adjacent body, and metallurgically joining each the body to the baseplate

Guanine nucleotide-binding protein subunit beta-2-like 1, a new Annexin A7 interacting protein

International Nuclear Information System (INIS)

Du, Yue; Meng, Jinyi; Huang, Yuhong; Wu, Jun; Wang, Bo; Ibrahim, Mohammed M.; Tang, Jianwu

2014-01-01

Highlights: • RACK1 formed a complex with Annexin A7. • Depletion of RACK1 inhibited the proliferation, migration and invasion. • RACK1 RNAi abolished RACK1-Annexin A7 interaction. • RACK1-Annexin A7 may play a role in regulating the metastatic potentials. - Abstract: We report for the first time that Guanine nucleotide-binding protein subunit beta-2-like 1 (RACK1) formed a complex with Annexin A7. Hca-F and Hca-P are a pair of syngeneic mouse hepatocarcinoma cell lines established and maintained in our laboratory. Our previous study showed that both Annexin A7 and RACK1 were expressed higher in Hca-F (lymph node metastasis >70%) than Hca-P (lymph node metastasis <30%). Suppression of Annexin A7 expression in Hca-F cells induced decreased migration and invasion ability. In this study, knockdown of RACK1 by RNA interference (RNAi) had the same impact on metastasis potential of Hca-F cells as Annexin A7 down-regulation. Furthermore, by co-immunoprecipitation and double immunofluorescence confocal imaging, we found that RACK1 was in complex with Annexin A7 in control cells, but not in the RACK1-down-regulated cells, indicating the abolishment of RACK1-Annexin A7 interaction in Hca-F cells by RACK1 RNAi. Taken together, these results suggest that RACK1-Annexin A7 interaction may be one of the means by which RACK1 and Annexin A7 influence the metastasis potential of mouse hepatocarcinoma cells in vitro

Development of segmented germanium detectors for neutrinoless double beta decay experiments

International Nuclear Information System (INIS)

Liu, Jing

2009-01-01

The results from neutrino oscillation experiments indicate that at least two neutrinos have mass. However, the value of the masses and whether neutrinos and anti-neutrinos are identical, i.e., Majorana particles, remain unknown. Neutrinoless double beta decay experiments can help to improve our understanding in both cases and are the only method currently possible to tackle the second question. The GERmanium Detector Array (GERDA) experiment, which will search for the neutrinoless double beta decay of 76 Ge, is currently under construction in Hall A of the INFN Gran Sasso National Laboratory (LNGS), Italy. In order to achieve an extremely low background level, segmented germanium detectors are considered to be operated directly in liquid argon which serves simultaneously as cooling and shielding medium. Several test cryostats were built at the Max-Planck-Institut fuer Physik in Muenchen to operate segmented germanium detectors both in vacuum and submerged in cryogenic liquid. The performance and the background discrimination power of segmented germanium detectors were studied in detail. It was proven for the first time that segmented germanium detectors can be operated stably over long periods submerged in a cryogenic liquid. It was confirmed that the segmentation scheme employed does well in the identification of photon induced background and demonstrated for the first time that also neutron interactions can be identified. The C++ Monte Carlo framework, MaGe (Majorana-GERDA), is a joint development of the Majorana and GERDA collaborations. It is based on GEANT4, but tailored especially to simulate the response of ultra-low background detectors to ionizing radiation. The predictions of the simulation were veri ed to be accurate for a wide range of conditions. Some shortcomings were found and corrected. Pulse shape analysis is complementary to segmentation in identifying background events. Its efficiency can only be correctly determined using reliable pulse shape

Development of segmented germanium detectors for neutrinoless double beta decay experiments

Energy Technology Data Exchange (ETDEWEB)

Liu, Jing

2009-06-09

The results from neutrino oscillation experiments indicate that at least two neutrinos have mass. However, the value of the masses and whether neutrinos and anti-neutrinos are identical, i.e., Majorana particles, remain unknown. Neutrinoless double beta decay experiments can help to improve our understanding in both cases and are the only method currently possible to tackle the second question. The GERmanium Detector Array (GERDA) experiment, which will search for the neutrinoless double beta decay of {sup 76}Ge, is currently under construction in Hall A of the INFN Gran Sasso National Laboratory (LNGS), Italy. In order to achieve an extremely low background level, segmented germanium detectors are considered to be operated directly in liquid argon which serves simultaneously as cooling and shielding medium. Several test cryostats were built at the Max-Planck-Institut fuer Physik in Muenchen to operate segmented germanium detectors both in vacuum and submerged in cryogenic liquid. The performance and the background discrimination power of segmented germanium detectors were studied in detail. It was proven for the first time that segmented germanium detectors can be operated stably over long periods submerged in a cryogenic liquid. It was confirmed that the segmentation scheme employed does well in the identification of photon induced background and demonstrated for the first time that also neutron interactions can be identified. The C++ Monte Carlo framework, MaGe (Majorana-GERDA), is a joint development of the Majorana and GERDA collaborations. It is based on GEANT4, but tailored especially to simulate the response of ultra-low background detectors to ionizing radiation. The predictions of the simulation were veri ed to be accurate for a wide range of conditions. Some shortcomings were found and corrected. Pulse shape analysis is complementary to segmentation in identifying background events. Its efficiency can only be correctly determined using reliable pulse

Reracking to increase spent fuel storage capacity

International Nuclear Information System (INIS)

1980-05-01

Many utilities have already increased their spent fuel pool storage capacity by replacing aluminum racks having storage densities as low as 0.2 MTU/ft 2 with stainless steel racks which can more than double storage densities. Use of boron-stainless steel racks or thin stainless steel cans containing reassembled fuel rods allows even higher fuel storage densities (up to approximately 1.25 MTU/ft 2 ). This report evaluates the economics of smaller storage gains that occur if pools, already converted to high density storage, are further reracked

Formation of double layers

International Nuclear Information System (INIS)

Leung, P.; Wong, A.Y.; Quon, B.H.

1981-01-01

Experiments on both stationary and propagating double layers and a related analytical model are described. Stationary double layers were produced in a multiple plasma device, in which an electron drift current was present. An investigation of the plasma parameters for the stable double layer condition is described. The particle distribution in the stable double layer establishes a potential profile, which creates electron and ion beams that excite plasma instabilities. The measured characteristics of the instabilities are consistent with the existence of the double layer. Propagating double layers are formed when the initial electron drift current is large. Ths slopes of the transition region increase as they propagate. A physical model for the formation of a double layer in the experimental device is described. This model explains the formation of the low potential region on the basis of the space charge. This space charge is created by the electron drift current. The model also accounts for the role of ions in double layer formation and explains the formation of moving double layers. (Auth.)

Measurement of the mixing leptonic parameter θ13 at the Double Chooz reactor antineutrino experiment

International Nuclear Information System (INIS)

Durand, V.

2012-01-01

The Double Chooz experiment aims at measuring the neutrino mixing parameter θ13 by studying the oscillations of de ν-bar e produced by the Chooz nuclear reactors located in France. The experimental concept consists in comparing the signal of two identical 10.3 m 3 detectors, allowing to cancel most of the experimental systematic uncertainties. The near detector, whose goal is the flux normalization and a measurement without oscillation, is expected to be delivered in 2013. The farthest detector from the source is taking data since April 2011 and is sensitive to θ 13 , which is expected to affect both the rate and the shape of the measured de ν-bar e . In this thesis, are first presented the Double Chooz experiment, with its ν-bar e source, its detection method, and the expected signal and backgrounds. In order to perform a selection, important quantities have to be reconstructed, calibrated, and saved in data files. The channel time offsets determination, the energy and vertex reconstruction algorithm CocoReco, the reconstruction packages of the Common Trunk, and the light trees maker Cheetah are especially presented. Concerning the data analysis, all the selection cuts and results for signal and backgrounds are discussed, particularly the multiplicity cut, the multiple off time window method, the lithium veto cut, and the cosmogenic 9 Li background studies. The Double Chooz experiment observed 8,249 de ν-bar e candidates in 227.93 days in its far detector only. The reactor antineutrino flux prediction used the Bugey 4 flux measurement after correction for differences in core composition. The expectation in case of no-oscillation is 8,937 events and this deficit is interpreted as evidence for ν-bar e disappearance. From a rate and shape analysis, is found sin 2 2θ = 0,109± 0,030 (stat) ± 0,025 (syst), with Δm 2 31 = 2,32 x 10 -3 eV 2 , while the no-oscillation hypothesis is even excluded at 2.9 σ. (author) [fr

The role of the RACK1 ortholog Cpc2p in modulating pheromone-induced cell cycle arrest in fission yeast.

Directory of Open Access Journals (Sweden)

Magdalena Mos

Full Text Available The detection and amplification of extracellular signals requires the involvement of multiple protein components. In mammalian cells the receptor of activated C kinase (RACK1 is an important scaffolding protein for signal transduction networks. Further, it also performs a critical function in regulating the cell cycle by modulating the G1/S transition. Many eukaryotic cells express RACK1 orthologs, with one example being Cpc2p in the fission yeast Schizosaccharomyces pombe. In contrast to RACK1, Cpc2p has been described to positively regulate, at the ribosomal level, cells entry into M phase. In addition, Cpc2p controls the stress response pathways through an interaction with Msa2p, and sexual development by modulating Ran1p/Pat1p. Here we describe investigations into the role, which Cpc2p performs in controlling the G protein-mediated mating response pathway. Despite structural similarity to Gβ-like subunits, Cpc2p appears not to function at the G protein level. However, upon pheromone stimulation, cells overexpressing Cpc2p display substantial cell morphology defects, disorientation of septum formation and a significantly protracted G1 arrest. Cpc2p has the potential to function at multiple positions within the pheromone response pathway. We provide a mechanistic interpretation of this novel data by linking Cpc2p function, during the mating response, with its previous described interactions with Ran1p/Pat1p. We suggest that overexpressing Cpc2p prolongs the stimulated state of pheromone-induced cells by increasing ste11 gene expression. These data indicate that Cpc2p regulates the pheromone-induced cell cycle arrest in fission yeast by delaying cells entry into S phase.

NMR parallel Q-meter with double-balanced-mixer detection for polarized target experiments

International Nuclear Information System (INIS)

Boissevain, J.; Tippens, W.B.

1983-01-01

A constant-voltage, parallel-tuned nuclear magnetic resonance (NMR) circuit, patterned after a Liverpool design, has been developed for polarized target experiments. Measuring the admittance of the resonance circuit allows advantageous use of double-balanced mixer detection. The resonant circuit is tolerant of stray capacitance between the NMR coil and the target cavity, thus easing target-cell-design constraints. The reference leg of the circuit includes a voltage-controlled attenuator and phase shifter for ease of tuning. The NMR output features a flat background and has good linearity and stability

Probing flavor models with {sup 76}Ge-based experiments on neutrinoless double-β decay

Energy Technology Data Exchange (ETDEWEB)

Agostini, Matteo [Technische Universitaet Muenchen, Physik Department and Excellence Cluster Universe, Munich (Germany); Gran Sasso Science Institute (INFN), L' Aquila (Italy); Merle, Alexander [Max-Planck-Institut fuer Physik (Werner-Heisenberg-Institut), Munich (Germany); Zuber, Kai [Technische Universitaet Dresden, Institute for Nuclear and Particle Physics, Dresden (Germany)

2016-04-15

The physics impact of a staged approach for double-β decay experiments based on {sup 76}Ge is studied. The scenario considered relies on realistic time schedules envisioned by the Gerda and the Majorana collaborations, which are jointly working towards the realization of a future larger scale {sup 76}Ge experiment. Intermediate stages of the experiments are conceived to perform quasi background-free measurements, and different data sets can be reliably combined to maximize the physics outcome. The sensitivity for such a global analysis is presented, with focus on how neutrino flavor models can be probed already with preliminary phases of the experiments. The synergy between theory and experiment yields strong benefits for both sides: the model predictions can be used to sensibly plan the experimental stages, and results from intermediate stages can be used to constrain whole groups of theoretical scenarios. This strategy clearly generates added value to the experimental efforts, while at the same time it allows to achieve valuable physics results as early as possible. (orig.)

Steel Rack Connections: Identification of Most Influential Factors and a Comparison of Stiffness Design Methods

Science.gov (United States)

Shah, S. N. R.; Sulong, N. H. Ramli; Shariati, Mahdi; Jumaat, M. Z.

2015-01-01

Steel pallet rack (SPR) beam-to-column connections (BCCs) are largely responsible to avoid the sway failure of frames in the down-aisle direction. The overall geometry of beam end connectors commercially used in SPR BCCs is different and does not allow a generalized analytic approach for all types of beam end connectors; however, identifying the effects of the configuration, profile and sizes of the connection components could be the suitable approach for the practical design engineers in order to predict the generalized behavior of any SPR BCC. This paper describes the experimental behavior of SPR BCCs tested using a double cantilever test set-up. Eight sets of specimens were identified based on the variation in column thickness, beam depth and number of tabs in the beam end connector in order to investigate the most influential factors affecting the connection performance. Four tests were repeatedly performed for each set to bring uniformity to the results taking the total number of tests to thirty-two. The moment-rotation (M-θ) behavior, load-strain relationship, major failure modes and the influence of selected parameters on connection performance were investigated. A comparative study to calculate the connection stiffness was carried out using the initial stiffness method, the slope to half-ultimate moment method and the equal area method. In order to find out the more appropriate method, the mean stiffness of all the tested connections and the variance in values of mean stiffness according to all three methods were calculated. The calculation of connection stiffness by means of the initial stiffness method is considered to overestimate the values when compared to the other two methods. The equal area method provided more consistent values of stiffness and lowest variance in the data set as compared to the other two methods. PMID:26452047

Steel Rack Connections: Identification of Most Influential Factors and a Comparison of Stiffness Design Methods.

Directory of Open Access Journals (Sweden)

S N R Shah

Full Text Available Steel pallet rack (SPR beam-to-column connections (BCCs are largely responsible to avoid the sway failure of frames in the down-aisle direction. The overall geometry of beam end connectors commercially used in SPR BCCs is different and does not allow a generalized analytic approach for all types of beam end connectors; however, identifying the effects of the configuration, profile and sizes of the connection components could be the suitable approach for the practical design engineers in order to predict the generalized behavior of any SPR BCC. This paper describes the experimental behavior of SPR BCCs tested using a double cantilever test set-up. Eight sets of specimens were identified based on the variation in column thickness, beam depth and number of tabs in the beam end connector in order to investigate the most influential factors affecting the connection performance. Four tests were repeatedly performed for each set to bring uniformity to the results taking the total number of tests to thirty-two. The moment-rotation (M-θ behavior, load-strain relationship, major failure modes and the influence of selected parameters on connection performance were investigated. A comparative study to calculate the connection stiffness was carried out using the initial stiffness method, the slope to half-ultimate moment method and the equal area method. In order to find out the more appropriate method, the mean stiffness of all the tested connections and the variance in values of mean stiffness according to all three methods were calculated. The calculation of connection stiffness by means of the initial stiffness method is considered to overestimate the values when compared to the other two methods. The equal area method provided more consistent values of stiffness and lowest variance in the data set as compared to the other two methods.

Facilities for studying the double beta decay processes

International Nuclear Information System (INIS)

Zdesenko, Yu.G.

1980-01-01

Modern state, tendencies and perspectiVes of the development of experimental installations to study double β-decay are treated. The main peculiarities of direct recognition and full experiments on the study of double β-decay are considered. A simple ratio is obtained from statistical considerations which connects the life time limits of the nuclei with the facility parameters to conduct direct recognition experiments. Possibilities of different detectors are evaluated on the basis of the ratio. Requirements for the modern technique for complete investigation of double β-decay are formulated and two designs of facilities meeting the requirements are considered. It is shown that the facility with proportional chambers is more perspective. On the basis of the analysis of the facility development to study double β-decay, conclusion is made that the final and unambiguous proof of the existence of double β-decay process can be obtained only directly in the experiments with immediate recording of the decay acts. Possibilities of the existing and developed facilities to conduct recognition (direct) experiments are such, that with their help life time limits as to neutronless double β-decay at the level of 10 21 -10 22 years can be established. Counters on the basis of the condensed noble gases, semiconductor detectors made of TeCd, scintillators of big volume are the most perspective detectors. To conduct complete experiments it is necessary to develop a facility with sensitivity sufficient for the detection of two-neutrino double β-activeness when Tsub(1/2)=10sup(21) years [ru

Experiments with a double solenoid system

Energy Technology Data Exchange (ETDEWEB)

Pampa Condori, R.; Lichtenthaeler Filho, R.; Faria, P.N. de; Lepine-Szily, A.; Mendes Junior, D.R.; Pires, K.C.C.; Assuncao, M.; Scarduelli, V.B.; Leistenschneider, E.; Morais, M.C.; Shorto, J.M.B.; Gasques, L. [Universidade de Sao Paulo (IF/USP), SP (Brazil). Inst. de Fisica

2012-07-01

Full text: RIBRAS [1] is presently the only experimental equipment in South America capable of producing secondary beams of rare isotopes. It consists of two superconducting solenoids, installed in one of the beam lines of the 8 MV Pelletron Tandem accelerator of the University of Sao Paulo. The exotic nuclei are produced in the collision between the primary beam of the Pelletron Accelerator and the primary target. The secondary beam is selected by the in-flight technique and is usually contaminated with particles coming from scattering and reactions in the primary target such as {sup 7}Li, alpha and other light particles as protons, deuterons and tritons. Solenoids are selectors with large acceptance and the double solenoid system provides ways to improve the quality of the secondary beam by using a degrador in the midst of the two solenoids. The main contamination of the secondary beam comes from {sup 7}Li{sup 2+} particles coming from the primary beam. A degrador placed between the two solenoids is able to separate those particles from the {sup 6}He beam providing an additional charge exchange {sup 7}Li{sup 2+-→}3{sup +}. In addition, the differential energy loss in the degrador provides further selection of the light particles as protons, deuterons, tritons and and alpha particles by the second solenoid. Here we present the results of the first experiment performed at RIBRAS using both solenoids. A pure {sup 6}He beam was produced and the reaction {sup 6}He+p was measured using a thick CH{sub 2} target. 1. R. Lichtenthaeler et al., Eur. Phys. J. A 25,s01,733 (2005) and Nucl. Phys. News 15, 25 (2005). (author)

The slow control system of the GERDA double beta decay experiment at Gran Sasso

International Nuclear Information System (INIS)

Brugnera, R; Garfagnini, A; Gigante, G; Hemmer, S; Zinato, D; Costa, F; Lippi, I; Michelotto, M; Ur, C

2012-01-01

GERDA is an experiment designed and built to study double beta decays of 76 Ge. It is currently in operation at the Gran Sasso underground laboratories (LNGS). A custom slow control system has been designed to monitor and control all the critical parameters for the proper functioning of the experiment. The main sub-components of the experiment (Cryostat, Clean Room, Water Tank, electronic crates and temperatures, High Voltage Systems, Radon Monitor and Source Insertion System) are constantly monitored by several distributed clients which write acquired data to a relational database (PostgreSQL). The latter allows to maintain a history of the whole experiment and, performing correlation between different and independent components, is useful to debug possible system malfunctions. The system is complemented by a Web server, a lightweight and efficient interface to the user on shifts and to the on-call experts, and by a dedicated Alarm dispatcher which distributes the errors generated by the components to the users allowing to react in short time. The whole project has been built around open source and custom software.

Results on neutrinoless double beta decay of 76Ge from the GERDA experiment

Science.gov (United States)

Palioselitis, Dimitrios

2015-05-01

The Germanium Detector Array (GERDA) experiment is searching for neutrinoless double beta (0νββ) decay of 76Ge, a lepton number violating nuclear process predicted by extensions of the Standard Model. GERDA is an array of bare germanium diodes immersed in liquid argon located at the Gran Sasso National Laboratory (LNGS) in Italy. The results of the GERDA Phase I data taking with a total exposure of 21.6 kg yr and a background index of 0.01 cts/(keV kg yr) are presented in this paper. No signal was observed and a lower limit of T1/20ν > 2.1×1025 yr (90% C.L.) was derived for the half-life of the 0νββ decay of 76Ge. Phase II of the experiment aims to reduce the background around the region of interest by a factor of ten.

Radiopurity control in the NEXT-100 double beta decay experiment: procedures and initial measurements

International Nuclear Information System (INIS)

Álvarez, V; Cárcel, S; Cervera, A; Díaz, J; Ferrario, P; Bandac, I; Bettini, A; Castel, J; Cebrián, S; Dafni, T; Borges, F I G M; Conde, C A N; Dias, T H V T; Fernandes, L M P; Freitas, E D C; Egorov, M; Gehman, V M; Esteve, R; Evtoukhovitch, P; Ferreira, A L

2013-01-01

The ''Neutrino Experiment with a Xenon Time-Projection Chamber'' (NEXT) is intended to investigate the neutrinoless double beta decay of 136 Xe, which requires a severe suppression of potential backgrounds. An extensive screening and material selection process is underway for NEXT since the control of the radiopurity levels of the materials to be used in the experimental set-up is a must for rare event searches. First measurements based on Glow Discharge Mass Spectrometry and gamma-ray spectroscopy using ultra-low background germanium detectors at the Laboratorio Subterr and apos;aneo de Canfranc (Spain) are described here. Activity results for natural radioactive chains and other common radionuclides are summarized, being the values obtained for some materials like copper and stainless steel very competitive. The implications of these results for the NEXT experiment are also discussed.

Heteroleptic metallosupramolecular racks, rectangles, and trigonal prisms: stoichiometry-controlled reversible interconversion.

Science.gov (United States)

Neogi, Subhadip; Lorenz, Yvonne; Engeser, Marianne; Samanta, Debabrata; Schmittel, Michael

2013-06-17

A simple approach toward preparation of heteroleptic two-dimensional (2D) rectangles and three-dimensional (3D) triangular prisms is described utilizing the HETPYP (HETeroleptic PYridyl and Phenanthroline metal complexes) concept. By mixing metal-loaded linear bisphenanthrolines of varying lengths with diverse (multi)pyridine (py) ligands in a proper ratio, six different self-assembled architectures arise cleanly and spontaneously in the absence of any template. They are characterized by (1)H and DOSY NMR, ESI-FT-ICR mass spectrometry as well as by Job plots and UV-vis titrations. Density functional theory (DFT) computations provide information about each structure. A stoichiometry-controlled supramolecule-to-supramolecule interconversion based on the relative amounts of metal bisphenanthroline and bipyridine forces the rectangular assembly to reorganize to a rack architecture and back to the rectangle, as clearly supported by variable temperature and DOSY NMR as well as dynamic light scattering data. The highly dynamic nature of the assemblies represents a promising starting point for constitutional dynamic materials.

Radiopurity assessment of the energy readout for the NEXT double beta decay experiment

Science.gov (United States)

Cebrián, S.; Pérez, J.; Bandac, I.; Labarga, L.; Álvarez, V.; Azevedo, C. D. R.; Benlloch-Rodríguez, J. M.; Borges, F. I. G. M.; Botas, A.; Cárcel, S.; Carrión, J. V.; Conde, C. A. N.; Díaz, J.; Diesburg, M.; Escada, J.; Esteve, R.; Felkai, R.; Fernandes, L. M. P.; Ferrario, P.; Ferreira, A. L.; Freitas, E. D. C.; Goldschmidt, A.; Gómez-Cadenas, J. J.; González-Díaz, D.; Gutiérrez, R. M.; Hauptman, J.; Henriques, C. A. O.; Hernandez, A. I.; Hernando Morata, J. A.; Herrero, V.; Jones, B. J. P.; Laing, A.; Lebrun, P.; Liubarsky, I.; López-March, N.; Losada, M.; Martín-Albo, J.; Martínez-Lema, G.; Martínez, A.; McDonald, A. D.; Monrabal, F.; Monteiro, C. M. B.; Mora, F. J.; Moutinho, L. M.; Muñoz Vidal, J.; Musti, M.; Nebot-Guinot, M.; Novella, P.; Nygren, D. R.; Palmeiro, B.; Para, A.; Querol, M.; Renner, J.; Ripoll, L.; Rodríguez, J.; Rogers, L.; Santos, F. P.; dos Santos, J. M. F.; Simón, A.; Sofka, C.; Sorel, M.; Stiegler, T.; Toledo, J. F.; Torrent, J.; Tsamalaidze, Z.; Veloso, J. F. C. A.; Villar, J. A.; Webb, R.; White, J. T.; Yahlali, N.

2017-08-01

The "Neutrino Experiment with a Xenon Time-Projection Chamber" (NEXT) experiment intends to investigate the neutrinoless double beta decay of 136Xe, and therefore requires a severe suppression of potential backgrounds. An extensive material screening and selection process was undertaken to quantify the radioactivity of the materials used in the experiment. Separate energy and tracking readout planes using different sensors allow us to combine the measurement of the topological signature of the event for background discrimination with the energy resolution optimization. The design of radiopure readout planes, in direct contact with the gas detector medium, was especially challenging since the required components typically have activities too large for experiments demanding ultra-low background conditions. After studying the tracking plane, here the radiopurity control of the energy plane is presented, mainly based on gamma-ray spectroscopy using ultra-low background germanium detectors at the Laboratorio Subterr&aposaneo de Canfranc (Spain). All the available units of the selected model of photomultiplier have been screened together with most of the components for the bases, enclosures and windows. According to these results for the activity of the relevant radioisotopes, the selected components of the energy plane would give a contribution to the overall background level in the region of interest of at most 2.4×10-4 counts keV-1 kg-1 y-1, satisfying the sensitivity requirements of the NEXT experiment.

Staphylococcus xylosus PCR-validated Decontamination of Murine Individually Ventilated Cage Racks and Air Handling Units by Using 'Active-Closed' Exposure to Vaporized Hydrogen Peroxide.

Science.gov (United States)

Ragland, Natalie H; Miedel, Emily L; Gomez, Jose M; Engelman, Robert W

2017-11-01

Vaporized hydrogen peroxide (VHP) is used to decontaminate clinical, biocontainment, and research animal rooms and equipment. To assist with its implementation in a murine facility, we developed a safe and effective method of VHP sterilization of IVC racks and air handling units (AHU). Safety of VHP decontamination was assessed by ensuring VHP levels dissipated to less than 1 ppm in the room prior to personnel reentry and inside the primary enclosure prior to the return of mice; this condition occurred at least 18 h after the VHP cycle. Efficacy of VHP sterilization was assessed by using chemical indicators, biologic indicators, and PCR testing for Staphylococcus xylosus, a commensal organism of murine skin and an opportunistic pathogen, which was present in 160 of 172 (93%) of specimens from occupied IVC racks and the interior surfaces of in-use AHU. Neither mechanized washing nor hand-sanitizing eradicated S. xylosus from equipment airway interiors, with 17% to 24% of specimens remaining PCR-positive for S. xylosus. 'Static-open' VHP exposure of sanitized equipment did not ensure its sterilization. In contrast, 'active-closed' VHP exposure, in which IVC racks were assembled, sealed, and connected to AHU set to the VHP cycle, increased the proportion of chemical indicators that detected sterilizing levels of VHP inside the assembled equipment, and significantly decreased PCR-detectable S. xylosus inside the equipment. Supplementing bulk steam sterilization of the primary enclosure with VHP sterilization of the secondary housing equipment during room change-outs may help to mitigate opportunistic agents that jeopardize studies involving immunodeficient strains.

Energy Performance Testing of Asetek's RackCDU System at NREL's High Performance Computing Data Center

Energy Technology Data Exchange (ETDEWEB)

Sickinger, D.; Van Geet, O.; Ravenscroft, C.

2014-11-01

In this study, we report on the first tests of Asetek's RackCDU direct-to-chip liquid cooling system for servers at NREL's ESIF data center. The system was simple to install on the existing servers and integrated directly into the data center's existing hydronics system. The focus of this study was to explore the total cooling energy savings and potential for waste-heat recovery of this warm-water liquid cooling system. RackCDU captured up to 64% of server heat into the liquid stream at an outlet temperature of 89 degrees F, and 48% at outlet temperatures approaching 100 degrees F. This system was designed to capture heat from the CPUs only, indicating a potential for increased heat capture if memory cooling was included. Reduced temperatures inside the servers caused all fans to reduce power to the lowest possible BIOS setting, indicating further energy savings potential if additional fan control is included. Preliminary studies manually reducing fan speed (and even removing fans) validated this potential savings but could not be optimized for these working servers. The Asetek direct-to-chip liquid cooling system has been in operation with users for 16 months with no necessary maintenance and no leaks.

Nemo-3 experiment assets and limitations. Perspective for the double β physics

International Nuclear Information System (INIS)

Augier, C.

2005-06-01

After an introduction to this report in Chapter 1, I present a status of our knowledge in neutrino physics in Chapter 2. Then, I detail in Chapter 3 all the choices made for the design and realisation of the NEMO 3 detector for the research of double beta decay process. Performance of the detector is presented, concerning both the capacity of the detector to identify the backgrounds and the ability to study all the ββ process. I also explain the methods chosen by the NEMO collaboration to reduce the radon activity inside the detector and to make this background negligible today. This chapter, which is written in English, is the 'Technical report of the NEMO 3 detector' and forms an independent report for the NEMO collaborators. I finish this report in Chapter 4 with a ten years prospect for experimental projects in physics, with both the SuperNEMO project and its experiment program, and also by comparing the most interesting experiments, CUORE and GERDA, showing as an example the effect of nuclear matrix elements on the neutrino effective mass measurement. (author)

Radon and material radiopurity assessment for the NEXT double beta decay experiment

Energy Technology Data Exchange (ETDEWEB)

Cebrián, S.; Dafni, T.; González-Díaz, D.; Herrera, D. C.; Irastorza, I. G.; Luzón, G.; Ortiz de Solórzano, A.; Villar, J. A. [Laboratorio de Física Nuclear y Astropartículas, Universidad de Zaragoza, C/ Pedro Cerbuna 12, 50009 Zaragoza (Spain); Laboratorio Subterráneo de Canfranc, Paseo de los Ayerbe s/n, 22880 Canfranc Estación, Huesca (Spain); Pérez, J. [Instituto de Física Teórica, UAM/CSIC, Campus de Cantoblanco, 28049 Madrid (Spain); Bandac, I. [Laboratorio Subterráneo de Canfranc, Paseo de los Ayerbe s/n, 22880 Canfranc Estación, Huesca (Spain); Labarga, L. [Dpto. de Física Teórica, Universidad Autónoma de Madrid, Campus de Cantoblanco, 28049 Madrid (Spain); Álvarez, V.; Cárcel, S.; Cervera, A.; Díaz, J.; Ferrario, P.; Gómez-Cadenas, J. J.; Laing, A.; Liubarsky, I.; López-March, N. [Instituto de Física Corpuscular, CSIC & Universitat de València, C/ Catedrático José Beltrán, 2, 46980 Paterna, Valencia (Spain); and others

2015-08-17

The ”Neutrino Experiment with a Xenon TPC” (NEXT), intended to investigate the neutrinoless double beta decay using a high-pressure xenon gas TPC filled with Xe enriched in {sup 136}Xe at the Canfranc Underground Laboratory in Spain, requires ultra-low background conditions demanding an exhaustive control of material radiopurity and environmental radon levels. An extensive material screening process is underway for several years based mainly on gamma-ray spectroscopy using ultra-low background germanium detectors in Canfranc but also on mass spectrometry techniques like GDMS and ICPMS. Components from shielding, pressure vessel, electroluminescence and high voltage elements and energy and tracking readout planes have been analyzed, helping in the final design of the experiment and in the construction of the background model. The latest measurements carried out will be presented and the implication on NEXT of their results will be discussed. The commissioning of the NEW detector, as a first step towards NEXT, has started in Canfranc; in-situ measurements of airborne radon levels were taken there to optimize the system for radon mitigation and will be shown too.

Measurement of the leptonic mixing parameter θ13 at the reactor antineutrino experiment Double Chooz

International Nuclear Information System (INIS)

Durand, V.

2014-01-01

The Double Chooz experiment aims at measuring the neutrino mixing parameter θ 13 by studying the oscillations of ν-bar e produced by the Chooz nuclear reactors located in France. The experimental concept consists in comparing the signal of 2 identical 10.3 m 3 detectors, allowing the cancellation of most of the experimental systematic uncertainties. The near detector, whose goal is the flux normalization and a measurement without oscillation, is expected to be delivered in 2013. The farthest detector from the source is taking data since april 2011 and is sensitive to θ 13 , which is expected to affect both the rate and the shape of measured ν-bar e . In 102 days with far detector only, 4121 ν-bar e candidates have been observed, while the expectation in case of no-oscillation is 4344 ± 165 events. This deficit is interpreted as evidence for ν-bar e disappearance. From a rate and shape analysis, it is found that sin 2 (θ 13 ) = [0.086±0.041(stat.)±0.030(syst)] with Δm 31 2 =2.4*10 -3 eV 2 , while the no-oscillation hypothesis is even excluded at 94.6%. We present in this document the concept and detection method of the Double Chooz experiment, along with its analysis strategy and first results on θ 13 . (author)

New Technique for Barium Daughter Ion Identification in a Liquid Xe-136 Double Beta Decay Experiment

International Nuclear Information System (INIS)

Fairbank, William

2016-01-01

This work addresses long-standing issues of fundamental interest in elementary particle physics. The most important outcome of this work is a new limit on neutrinoless double beta decay. This is an extremely rare and long-sought-after type of radioactive decay. If discovered, it would require changes in the standard model of the elementary constituents of matter, and would prove that neutrinos and antineutrinos are the same, a revolutionary concept in particle physics. Neutrinos are major components of the matter in the universe that are so small and so weakly interacting with other matter that their masses have not yet been discovered. A discovery of neutrinoless double beta decay could help determine the neutrino masses. An important outcome of the work on this project was the Colorado State University role in operating the EXO-200 neutrinoless double beta decay experiment and in analysis of the data from this experiment. One type of double beta decay of the isotope "1"3"6Xe, the two-neutrino variety, was discovered in this work. Although the other type of double beta decay, the neutrinoless variety, was not yet discovered in this work, a world's best sensitivity of 1.9x10"2"5 year half-life was obtained. This result rules out a previous claim of a positive result in a different isotope. This work also establishes that the masses of the neutrinos are less than one millionth of that of electrons. A unique EXO-200 analysis, in which the CSU group had a leading role, has established for the first time ever in a liquid noble gas the fraction of daughter atoms from alpha and beta decay that are ionized. This result has important impact on other pending studies, including nucleon decay and barium tagging. Novel additional discoveries include multiphoton ionization of liquid xenon with UV pulsed lasers, which may find application in calibration of future noble liquid detectors, and studies of association and dissociation reactions of Ba"+ ions in gaseous xenon. Through

New Technique for Barium Daughter Ion Identification in a Liquid Xe-136 Double Beta Decay Experiment

Energy Technology Data Exchange (ETDEWEB)

Fairbank, William [Colorado State Univ., Fort Collins, CO (United States)

2016-06-08

This work addresses long-standing issues of fundamental interest in elementary particle physics. The most important outcome of this work is a new limit on neutrinoless double beta decay. This is an extremely rare and long-sought-after type of radioactive decay. If discovered, it would require changes in the standard model of the elementary constituents of matter, and would prove that neutrinos and antineutrinos are the same, a revolutionary concept in particle physics. Neutrinos are major components of the matter in the universe that are so small and so weakly interacting with other matter that their masses have not yet been discovered. A discovery of neutrinoless double beta decay could help determine the neutrino masses. An important outcome of the work on this project was the Colorado State University role in operating the EXO-200 neutrinoless double beta decay experiment and in analysis of the data from this experiment. One type of double beta decay of the isotope ¹³⁶Xe, the two-neutrino variety, was discovered in this work. Although the other type of double beta decay, the neutrinoless variety, was not yet discovered in this work, a world’s best sensitivity of 1.9x10²⁵ year half-life was obtained. This result rules out a previous claim of a positive result in a different isotope. This work also establishes that the masses of the neutrinos are less than one millionth of that of electrons. A unique EXO-200 analysis, in which the CSU group had a leading role, has established for the first time ever in a liquid noble gas the fraction of daughter atoms from alpha and beta decay that are ionized. This result has important impact on other pending studies, including nucleon decay and barium tagging. Novel additional discoveries include multiphoton ionization of liquid xenon with UV pulsed lasers, which may find application in calibration of future noble liquid detectors, and studies of association and dissociation reactions of Ba

Choosing Double: The Relationship between Successful AP® Exams and College Double Major

Science.gov (United States)

Ewing, Maureen; Jagesic, Sanja; Wyatt, Jeff

2018-01-01

Students who double major have higher earnings and are more satisfied with their educational experience in college than those who graduate with a single major. In this study, the authors examine the extent to which a student's experience with academic acceleration programs in high school, specifically successful participation in the Advanced…

ECONOMIC EVALUATION OF MAINTAINING THE CAPACITY OF TRASH RACKS IN HYDRAULIC ENGINEERING STRUCTURES

Directory of Open Access Journals (Sweden)

Natalia Walczak

2017-05-01

Full Text Available Considering the limited capabilities of obtaining energy in a traditional way from coal combustion and the requirements of the European Union, other alternative energy sources should be sought. They have been being increasingly used by business entities and individual investors and are designed to provide financial profits, which will be ensured only with correct operation of the energy system. One of examples of alternative energy sources application is the construction of small hydropower plants, where the efficiency of all elements included is of great importance. The article analyses financial losses incurred by owners of power plants when the energy system lacks 100% capacity of the inlet channel. Material that accumulates on SHP trash racks might be analysed in two ways: biologically (these are screenings – as in wastewater treatment plants and hydraulically.

46 CFR Appendix A to Part 520 - Standard Terminology and Codes

Science.gov (United States)

2010-10-01

... cargo by American-flag common carriers. P Addition of a port or point. R Reduction. S Special Case... HH Hardtop HT Insulated IN Open Top OT Dry PC Platform PL Reefer RE Tank TC Top Loader TL Trailer TR... Carton CTN Cylinder CYL Dry Bulk DBK Double-length Rack DRK Drum DRM Double-length Skid DSK Double-length...

Phase II Upgrade of the GERDA Experiment for the Search of Neutrinoless Double Beta Decay

Science.gov (United States)

Majorovits, B.

Observation of neutrinoless double beta decay could answer the question regarding the Majorana or Dirac nature of neutrinos. The GERDA experiment utilizes HPGe detectors enriched with the isotope 76Ge to search for this process. Recently the GERDA collaboration has unblinded data of Phase I of the experiment. In order to further improve the sensitivity of the experiment, additionally to the coaxial detectors used, 30 BEGe detectors made from germanium enriched in 76Ge will be deployed in GERDA Phase II. BEGe detectors have superior PSD capability, thus the background can be further reduced. The liquid argon surrounding the detector array will be instrumented in order to reject background by detecting scintillation light induced in the liquid argon by radiation. After a short introduction the hardware preparations for GERDA Phase II as well as the processing and characterization of the 30 BEGe detectors are discussed.

Search for Tau Neutrinos in the τ → e Decay Channel in the OPERA Experiment

OpenAIRE

Hosseini, Behzad

2015-01-01

The OPERA (Oscillation Project with Emulsion tRacking Apparatus) experiment is a long baseline neutrino oscillation experiment that was designed to perform a conclusive test of the νμ → ντ oscillations hypothesis. The main aim of this experiment is a direct observation of τ leptons in ντ charged-current interactions. A good electromagnetic shower reconstruction is important for the τ detection in the τ → e decay channel. So far, 4 ντ candidates have been observed in the OPERA detector wi...

Measurement of double polarization observables in 2π{sup 0}-photoproduction off the proton with the CBELSA/TAPS-experiment

Energy Technology Data Exchange (ETDEWEB)

Mahlberg, Philipp [Helmholtz-Institut fuer Strahlen- und Kernphysik, Bonn (Germany); Collaboration: CBELSA/TAPS-Collaboration

2016-07-01

In contrast to the atomic spectrum with its sharp and well defined excitation levels, the nucleon excitation spectrum is dominated by broad, overlapping resonances. Partial wave analyses are needed to extract the contributing resonances from the experimental data. In order to find an unambiguous solution, the measurement of polarization observables is indispensable. The Crystal Barrel/TAPS experiment at the electron accelerator ELSA is, due to its high photon detection efficiency and its almost complete solid angle coverage, ideally suited to measure neutral mesons decaying into photons. The measurement with double polarization, i.e. a circularly polarized photon beam and a longitudinally polarized target provides access to single and double polarization observables. At higher energies, the cross sections show that multi-meson decay channels gain in importance compared e.g. to single pseudoscalar meson photoproduction. In this talk, preliminary results for the helicity asymmetry E in 2π{sup 0}-photoproduction measured with the CBELSA/TAPS experiment are presented.

Astronaut James S. Voss Performs Tasks in the Destiny Laboratory

Science.gov (United States)

2001-01-01

Astronaut James S. Voss, Expedition Two flight engineer, works with a series of cables on the EXPRESS Rack in the United State's Destiny laboratory on the International Space Station (ISS). The EXPRESS Rack is a standardized payload rack system that transports, stores, and supports experiments aboard the ISS. EXPRESS stands for EXpedite the PRocessing of Experiments to the Space Station, reflecting the fact that this system was developed specifically to maximize the Station's research capabilities. The EXPRESS Rack system supports science payloads in several disciplines, including biology, chemistry, physics, ecology, and medicine. With the EXPRESS Rack, getting experiments to space has never been easier or more affordable. With its standardized hardware interfaces and streamlined approach, the EXPRESS Rack enables quick, simple integration of multiple payloads aboard the ISS. The system is comprised of elements that remain on the ISS, as well as elements that travel back and forth between the ISS and Earth via the Space Shuttle.

Staphylococcus xylosus PCR-validated Decontamination of Murine Individually Ventilated Cage Racks and Air Handling Units by Using ‘Active–Closed’ Exposure to Vaporized Hydrogen Peroxide

Science.gov (United States)

Ragland, Natalie H; Miedel, Emily L; Gomez, Jose M; Engelman, Robert W

2017-01-01

Vaporized hydrogen peroxide (VHP) is used to decontaminate clinical, biocontainment, and research animal rooms and equipment. To assist with its implementation in a murine facility, we developed a safe and effective method of VHP sterilization of IVC racks and air handling units (AHU). Safety of VHP decontamination was assessed by ensuring VHP levels dissipated to less than 1 ppm in the room prior to personnel reentry and inside the primary enclosure prior to the return of mice; this condition occurred at least 18 h after the VHP cycle. Efficacy of VHP sterilization was assessed by using chemical indicators, biologic indicators, and PCR testing for Staphylococcus xylosus, a commensal organism of murine skin and an opportunistic pathogen, which was present in 160 of 172 (93%) of specimens from occupied IVC racks and the interior surfaces of in-use AHU. Neither mechanized washing nor hand-sanitizing eradicated S. xylosus from equipment airway interiors, with 17% to 24% of specimens remaining PCR-positive for S. xylosus. ‘Static–open’ VHP exposure of sanitized equipment did not ensure its sterilization. In contrast, ‘active–closed’ VHP exposure, in which IVC racks were assembled, sealed, and connected to AHU set to the VHP cycle, increased the proportion of chemical indicators that detected sterilizing levels of VHP inside the assembled equipment, and significantly decreased PCR-detectable S. xylosus inside the equipment. Supplementing bulk steam sterilization of the primary enclosure with VHP sterilization of the secondary housing equipment during room change-outs may help to mitigate opportunistic agents that jeopardize studies involving immunodeficient strains. PMID:29256369

Neutron-induced Backgrounds in 134Xe for Large-Scale Neutrinoless Double-Beta Decay Experiments

Science.gov (United States)

Moriguchi, Nina; Kidd, Mary; Tornow, Werner

2016-09-01

136Xe is used in large neutrinoless double-beta (0 νββ) decay experiments, such as KamLAND- Zen and EXO 200. Though highly purified, 136Xe still contains a significant amount of 134Xe. Recently, a new nuclear energy level was found in 134Xe. If 134Xe decays from this proposed excited state, it will emit a 2485.7 keV gamma ray. Because this energy lies near the region of interest of 136Xe νββ decay experiments (Q value 2457.8 keV), it could make a significant contribution to the background. A purified gaseous sample of 134Xe will be irradiated with neutrons of an incident energy of 4.0 MeV at Triangle Universities Nuclear Laboratory and monitored with high-purity germanium detectors. The spectra obtained from these detectors will be analyzed for the presence of the 2581 keV gamma ray. We will report on the status of this experiment. Future plans include expanding this measurement to higher initial neutron energies. Tennesse Tech University CISE Grant program.

A double layer review

International Nuclear Information System (INIS)

Block, L.P.

1977-06-01

A review of the main results on electrostatic double layers (sometimes called space charge layers or sheaths) obtained from theory, and laboratory and space experiments up to the spring of 1977 is given. By means of barium jets and satellite probes, double layers have now been found at the altitudes, earlier predicted theoretically. The general potential distribution above the auroral zone, suggested by inverted V-events and electric field reversals, is corroborated. (author)

Radon-induced surface contaminations in neutrinoless double beta decay and dark matter experiments

International Nuclear Information System (INIS)

Pattavina, L.

2011-01-01

In experiments looking for rare events, like neutrinoless double beta decay (DBD0ν) and dark matter search (DM), one of the main issues is to increase the experimental sensitivity through the material selection and production. The background contribution coming from the materials used for the detector realization has to be minimized. Moreover the net reduction of the background produced by the bulk part of the apparatus has raised concerns about the background contribution coming from the surfaces. Many procedures and techniques were developed during the last years in order to remove and to minimize the presence of possible contaminants on detector surfaces. To succeed in this strategy a big effort was put in defining all possible mechanisms that lead to surface contaminations, as well as specific cleaning procedures, which are able to reduce and control the surface radioactivity. The presence in air and gases of possible radioactive elements that can stick on the detector surfaces can lead to a recontamination process that will vanish all the applied cleaning procedures. Here is presented and analyzed the contribution to the background of rare events experiments like CUORE experiment (DBD0ν) and EDELWEISS experiment (DM) produced by an exposure of their detector components to a big activity of 222 Rn, radioactive daughter isotope from the 238 U chain. (author)

Loss of coherence in double-slit diffraction experiments

NARCIS (Netherlands)

Sanz, A.S.; Borondo, F.; Bastiaans, M.J.

2005-01-01

By using optical models based on the theory of partially coherent light, and the quantum decoherence model proposed by Joos and Zeh [Z. Phys. B 59, 223 (1985)], we explore incoherence and decoherence in interference phenomena. The problem chosen to study is that of the double-slit diffraction

Dynamics of vacuum-sealed, double-leaf partitions

Science.gov (United States)

Kavanaugh, Joshua Stephen

The goal of this research is to investigate the feasibility and potential effectiveness of using vacuum-sealed, double-leaf partitions for applications in noise control. Substantial work has been done previously on double-leaf partitions where the acoustics of the inner chamber and mechanical vibrations of structural supports are passively and actively controlled. The work presented here is unique in that the proposed system aims to eliminate the need for active acoustic control of transmitted acoustic energy by removing all the air between the two panels of the double partition. Therefore, the only remaining energy paths would be along the boundary and at the points where there are intermediate structural supports connecting the two panels. The eventual goal of the research is to develop a high-loss double-leaf partition that simplifies active control by removing the need for control of the air cavity and channeling all the energy into discrete structural paths. The work presented here is a first step towards the goal of designing a high-loss, actively-controlled double-leaf partition with an air-evacuated inner chamber. One experiment is conducted to investigate the effects of various levels of vacuum on the response of a double-leaf partition whose panels are mechanically coupled only at the boundary. Another experiment is conducted which investigates the effect of changing the stiffness of an intermediate support coupling the two panels of a double-leaf partition in which a vacuum has been applied to the inner cavity. The available equipment was able to maintain a 99% vacuum between the panels. Both experiments are accompanied by analytical models used to investigate the importance of various dynamic parameters. Results show that the vacuum-sealed system shows some potential for increased transmission loss, primarily by the changing the natural frequencies of the double-leaf partition.

Improved Reactive Flow Modeling of the LX-17 Double Shock Experiments

Science.gov (United States)

Rehagen, Thomas J.; Vitello, Peter

2017-06-01

Over driven double shock experiments provide a measurement of the properties of the reaction product states of the insensitive high explosive LX-17 (92.5% TATB and 7.5% Kel-F by weight). These experiments used two flyer materials mounted on the end of a projectile to send an initial shock through the LX-17, followed by a second shock of a higher magnitude into the detonation products. In the experiments, the explosive was initially driven by the flyer plate to pressures above the Chapman-Jouguet state. The particle velocity history was recorded by Photonic Doppler Velocimetry (PDV) probes pointing at an aluminum foil coated LiF window. The PDV data shows a sharp initial shock and decay, followed by a rounded second shock. Here, the experimental results are compared to 2D and 3D Cheetah reactive flow modeling. Our default Cheetah reactive flow model fails to accurately reproduce the decay of the first shock or the curvature or strength of the second shock. A new model is proposed in which the carbon condensate produced in the reaction zone is controlled by a kinetic rate. This allows the carbon condensate to be initially out of chemical equilibrium with the product gas. This new model reproduces the initial detonation peak and decay, and matches the curvature of the second shock, however, it still over-predicts the strength of the second shock. This work was performed under the auspices of the U.S. Department of Energy by Lawrence Livermore National Laboratory under Contract No. DE-AC52-07NA27344.

Search for Neutrinoless Double-Beta Decay

OpenAIRE

Tornow, Werner

2014-01-01

After the pioneering work of the Heidelberg-Moscow (HDM) and International Germanium Experiment (IGEX) groups, the second round of neutrinoless double-$\\beta$ decay searches currently underway has or will improve the life-time limits of double-$\\beta$ decay candidates by a factor of two to three, reaching in the near future the $T_{1/2} = 3 \\times 10^{25}$ yr level. This talk will focus on the large-scale experiments GERDA, EXO-200, and KamLAND-Zen, which have reported already lower half-life...

A measurement of the 2 neutrino double beta decay rate of Te-130 in the CUORICINO experiment

Energy Technology Data Exchange (ETDEWEB)

Kogler, Laura K. [Univ. of California, Berkeley, CA (United States)

2011-11-30

CUORICINO was a cryogenic bolometer experiment designed to search for neutrinoless double beta decay and other rare processes, including double beta decay with two neutrinos (2vββ). The experiment was located at Laboratori Nazionali del Gran Sasso and ran for a period of about 5 years, from 2003 to 2008. The detector consisted of an array of 62 TeO₂ crystals arranged in a tower and operated at a temperature of 10 mK. Events depositing energy in the detectors, such as radioactive decays or impinging particles, produced thermal pulses in the crystals which were read out using sensitive thermistors. The experiment included 4 enriched crystals, 2 enriched with ¹³⁰Te and 2 with ¹²⁸Te, in order to aid in the measurement of the 2vββ rate. The enriched crystals contained a total of 350 g ¹³⁰Te. The 128-enriched (130-depleted) crystals were used as background monitors, so that the shared backgrounds could be subtracted from the energy spectrum of the 130- enriched crystals. Residual backgrounds in the subtracted spectrum were fit using spectra generated by Monte-Carlo simulations of natural radioactive contaminants located in and on the crystals. The 2vββ half-life was measured to be T^2v_1/2 = [9.81± 0.96(stat)± 0.49(syst)] x10²⁰ y.

Double ambidexterity

DEFF Research Database (Denmark)

Kaulio, Matti; Thorén, Kent; Rohrbeck, René

2017-01-01

We leverage the business model innovation and ambidexterity literature to investigate a contradictory case, the Swedish-Finnish Telecom operator TeliaSonera. Despite being challenged by three major disruptions, the company not only still exists but also enjoys remarkably good financial performance....... Building on extant archival data and interviews, we carefully identify and map 26 organizational responses during 1992–2016. We find that the firm has overcome three critical phases by experimenting and pioneering with portfolios of business models and/or technological innovations. We describe...... this behaviour as double ambidexterity. We use an in-depth case study to conceptualize double ambidexterity and discuss its impact on the business's survival and enduring success....

The design and construction of a double-sided Silicon Microvertex Detector for the L3 experiment at CERN

International Nuclear Information System (INIS)

Adam, A.; Ambrosi, G.; Babucci, E.; Bertucci, B.; Biasini, M.; Bilei, G.M.; Caria, M.; Checcucci, B.; Easo, S.; Fiandrini, E.; Krastev, V.R.; Massetti, R.; Pauluzzi, M.; Santocchia, A.; Servoli, L.; Baschirotto, A.; Bosetti, M.; Pensotti, S.; Rancoita, P.G.; Rattaggi, M.; Terzi, G.; Battiston, R.; Bay, A.; Burger, W.J.; Extermann, P.; Perrin, E.; Susinno, G.F.; Bencze, G.Y.L.; Kornis, J.; Toth, J.; Bobbink, G.J.; Duinker, P.; Brooks, M.L.; Coan, T.E.; Kapustinsky, J.S.; Kinnison, W.W.; Lee, D.M.; Mills, G.B.; Thompson, T.C.; Busenitz, J.; DiBitonto, D.; Camps, C.; Commichau, V.; Hangartner, K.; Schmitz, P.; Chen, A.; Hou, S.; Lin, W.T.; Gougas, A.; Kim, D.; Paul, T.; Hauviller, C.; Herve, A.; Josa, I.; Landi, G.; Lebeau, M.; Lecomte, P.; Viertel, G.M.; Waldmeier, S.; Leiste, R.; Lejeune, E.; Weill, R.; Lohmann, W.; Nowak, H.; Sachwitz, M.; Schoeniech, B.; Tonisch, F.; Trowitzsch, G.; Vogt, H.; Passaleva, G.; Yeh, S.C.

1993-01-01

A Silicon Microvertex Detector (SMD) has been commissioned for the L3 experiment at the Large Electron-Positron colliding-beam accelerator (LEP) at the European Center for Nuclear Physics, (CERN). The SMD is a 72,672 channel, two layer barrel tracker that is comprised of 96 ac-coupled, double-sided silicon detectors. Details of the design and construction are presented

Double-duty caregivers: healthcare professionals juggling employment and informal caregiving. A survey on personal health and work experiences.

Science.gov (United States)

Boumans, Nicolle P G; Dorant, Elisabeth

2014-07-01

This study compared the work-related experiences and personal health status of double-duty caregivers with those of caregivers who do not provide informal care to a family member or close friend in need. The interest in providing informal care alongside employment is growing. However, little attention has been paid to the dual role of the healthcare professional who also has caregiving responsibilities for a needy person in his/her private situation. It is important to study the negative and positive consequences of this combination of professional and family care giving. A cross-sectional study. In 2011, we distributed a digital questionnaire to employees with a professional care function working at a healthcare organization in the Netherlands. Descriptive statistics, analyses of covariance and tests of linearity were performed. Analyses of variance demonstrated that as professional healthcare workers provide more hours of informal care in their private lives, their mental and physical health significantly worsens, while their need for recovery increases. Also, statistical significant increases were seen for emotional exhaustion, presenteeism and negative experiences with Work-Home and Home-Work Interferences. Remarkably, positive Home-Work Interference increased significantly with increasing hours of informal care. Double-duty caregivers appeared to be equally motivated and satisfied with their work as their co-workers. No differences were seen with respect to absenteeism. Double-duty caregivers prove to be employees who are at risk of developing symptoms of overload. This finding calls for special attention, with long-term solutions at both legislative and organizational level. © 2013 John Wiley & Sons Ltd.

The NEXT-100 experiment for neutrinoless double beta decay searches (Conceptual Design Report)

CERN Document Server

Álvarez, V; Batallé, M; Bayarri, J; Borges, F I G; Cárcel, S; Carmona, J M; Castel, J; Catalá, J M; Cebrián, S; Cervera-Villanueva, A; Chan, D; Conde, C A N; Dafni, T; Dias, T H V T; Díaz, J; Esteve, R; Evtoukhovitch, P; Fernandes, L M P; Ferrario, P; Ferrer-Ribas, E; Ferreira, A L; Freitas, E D C; Gil, A; Giomataris, I; Goldschmidt, A; Gómez, E; Gómez, H; Gómez-Cadenas, J J; Gónzález, K; Gutiérrez, R M; Hernando-Morata, J A; Herrera, D C; Herrero, V; Iguaz, F; Irastorza, I G; Kalinnikov, V; Kustov, A; Liubarsky, I; Lopes, J A M; Lorca, D; Losada, M; Luzón, G; Martín-Albo, J; Méndez, A; Miller, T; Moisenko, A; Mols, J P; Monrabal, F; Monteiro, C M B; Monzó, J M; Mora, F J; Muñoz-Vidal, J; da Luz, H Natal; Navarro, G; Nebot, M; Nygren, D; Oliveira, C A B; Palma, R; Pérez-Aparicio, J L; Renner, J; Ripoll, L; Rodríguez, A; Rodríguez, J; Santos, F P; Santos, J M F dos; Seguí, L; Serra, L; Sofka, C; Sorel, M; Spieler, H; Toledo, J F; Tomás, A; Tsamalaidze, Z; Vázquez, D; Velicheva, E; Veloso, J F C A; Villar, J A; Webb, R; Weber, T; White, J; Yahlali, N

2011-01-01

We propose an EASY (Electroluminescent ApparatuS of high Yield) and SOFT (Separated Optimized FuncTion) time-projection chamber for the NEXT experiment, that will search for neutrinoless double beta decay (bb0nu) in Xe-136. Our experiment must be competitive with the new generation of bb0nu searches already in operation or in construction. This requires a detector with very good energy resolution (<1%), very low background con- tamination (1E-4 counts/(keV \\bullet kg \\bullet y)) and large target mass. In addition, it needs to be operational as soon as possible. The design described here optimizes energy resolution thanks to the use of proportional electroluminescent amplification (EL); it is compact, as the Xe gas is under high pressure; and it allows the measurement of the topological signature of the event to further reduce the background contamination. The SOFT design uses different sensors for tracking and calorimetry. We propose the use of SiPMs (MPPCs) coated with a suitable wavelength shifter for th...

Purifications of calcium carbonate and molybdenum oxide powders for neutrinoless double beta decay experiment, AMoRE

International Nuclear Information System (INIS)

Park, HyangKyu

2015-01-01

The AMoRE (Advanced Mo based Rare process Experiment) collaboration is going to use calcium molybdate crystals to search for neutrinoless double beta decay of 100 Mo isotope. In order to make the crystal, we use calcium carbonate and molybdenum oxide powders as raw materials. Therefore it is highly necessary to reduce potential sources for radioactive backgrounds such as U and Th in the powders. In this talk, we will present our studies for purification of calcium carbonate and molybdenum oxide powders

Rack-1, GAPDH3, and actin: proteins of Myzus persicae potentially involved in the transcytosis of beet western yellows virus particles in the aphid

International Nuclear Information System (INIS)

Seddas, Pascale; Boissinot, Sylvaine; Strub, Jean-Marc; Dorsselaer, Alain van; Regenmortel, Marc H.V. van; Pattus, Franc

2004-01-01

Beet western yellows virus (BWYV) is a Polerovirus that relies on the aphid Myzus persicae for its transmission, in a persistent-circulative mode. To be transmitted, the virus must cross the midgut and the accessory salivary glands (ASG) epithelial barriers in a transcytosis mechanism where vector receptors interact with virions. In this paper, we report in vitro interaction experiments between BWYV and aphid components. Using the M. persicae clone from Colmar, we showed that a set of aphid polypeptides, separated by SDS-PAGE or 2D electrophoresis (2DE), can bind in vitro to purified wild type or mutant particles. Using subcellular fractionation, we showed that the 65-kDa polypeptide identified as symbionin is a soluble protein whereas the other polypeptides seem to be associated more or less strongly to the membrane. We hypothesize that three polypeptides, identified by mass spectrometry as Rack-1, GAPDH3, and actin, may be involved in the epithelial transcytosis of virus particles in the aphid vector

Symmetry breaking in spreading RAT2 fibroblasts requires the MAPK/ERK pathway scaffold RACK1 that integrates FAK, p190A-RhoGAP and ERK2 signaling

Czech Academy of Sciences Publication Activity Database

Klímová, Zuzana; Bráborec, Vojtěch; Maninová, Miloslava; Čáslavský, Josef; Weber, M. J.; Vomastek, Tomáš

2016-01-01

Roč. 1863, č. 9 (2016), s. 2189-2200 ISSN 0167-4889 R&D Projects: GA ČR GA13-06405S Institutional support: RVO:61388971 Keywords : RACK1 * ERK * FAK Subject RIV: EB - Genetics ; Molecular Biology Impact factor: 4.521, year: 2016

DAQ

CERN Multimedia

Gomez-Reino Garrido

Rack Control In order to operate and monitor CMS detector, a large amount of electronic equipment is being installed in around five hundred racks. These racks, full of PCs and other industrial and custom electronic instruments, should be closely controlled and monitored on a full time basis. For this purpose, CMS has developed a Rack Control & Monitoring software application that is also used by the rest of LHC experiments. On the control side, this application interfaces the electrical distribution system allowing to power on and power off individual or groups of racks. For the rack environment monitoring part, the rack control software communicates with CERN made monitoring boards installed in every rack. These boards provide, among other information, temperature, humidity and air flow readings inside each rack. Some automated actions are performed by the tool to anticipate and, if possible, prevent safety system actions in the racks. Racks are automatically switched off if temperature or dew point r...

Brief Report: Oxytocin Enhances Paternal Sensitivity to a Child with Autism--A Double-Blind Within-Subject Experiment with Intranasally Administered Oxytocin

Science.gov (United States)

Naber, Fabienne B. A.; Poslawsky, Irina E.; van Ijzendoorn, Marinus H.; van Engeland, Herman; Bakermans-Kranenburg, Marian J.

2013-01-01

Oxytocin seems associated with parenting style, and experimental work showed positive effects of intranasally administered oxytocin on parenting style of fathers. Here, the first double-blind, placebo-controlled, within-subject experiment with intranasal oxytocin administration to fathers of children with autism spectrum disorder (ASD) is…

Proposal for the award of a contract for the supply of connection boxes for electrical racks for the LHC magnets

CERN Document Server

2004-01-01

This document concerns the award of a contract for the supply of 1670 connection boxes for two different types of electrical racks for the LHC magnets. The Finance Committee is invited to agree to the negotiation of an ex-works contract with CRAWFORD, HANSFORD & KIMBER (GB), for the supply of 1670 connection boxes for a total amount of 473 774 pounds sterling (1 080 442 Swiss francs), not subject to revision. The rate of exchange used is that stipulated in the tender.

Young's double-slit interference with two-color biphotons.

Science.gov (United States)

Zhang, De-Jian; Wu, Shuang; Li, Hong-Guo; Wang, Hai-Bo; Xiong, Jun; Wang, Kaige

2017-12-12

In classical optics, Young's double-slit experiment with colored coherent light gives rise to individual interference fringes for each light frequency, referring to single-photon interference. However, two-photon double-slit interference has been widely studied only for wavelength-degenerate biphoton, known as subwavelength quantum lithography. In this work, we report double-slit interference experiments with two-color biphoton. Different from the degenerate case, the experimental results depend on the measurement methods. From a two-axis coincidence measurement pattern we can extract complete interference information about two colors. The conceptual model provides an intuitional picture of the in-phase and out-of-phase photon correlations and a complete quantum understanding about the which-path information of two colored photons.

Majorana neutrinos and double beta-decay

International Nuclear Information System (INIS)

Shchepkin, M.G.

1986-01-01

Problem, related to neutrino mass and lepton charge L conservation is briefly discussed. A possibility to experimentally test L conservation in different processes and to produce limitations for neutrino mass in double beta-decay processes is considered. Planned experiments on studying the double neutrinoless (2β) beta-decays and searching 2β(2ν)-decays, permitted by the conservation laws, are discussed. It is stressed, that comparison of the existing theoretical predictions of 2β(2ν)-decay probability with experimental results will make it possible to choose the most adequate approach to the calculation of double β-transition nuclear amplitudes

[Sciatica. From stretch rack to microdiscectomy].

Science.gov (United States)

Gruber, P; Böni, T

2015-12-01

In ancient times as well as in the Middle Ages treatment options for discogenic nerve compression syndrome were limited and usually not very specific because of low anatomical and pathophysiological knowledge. The stretch rack (scamnum Hippocratis) was particularly prominent but was widely used as a therapeutic device for very different spinal disorders. Since the beginning of the nineteenth century anatomical knowledge increased and the advances in the fields of asepsis, anesthesia and surgery resulted in an increase in surgical interventions on the spine. In 1908 the first successful lumbar discectomy was initiated and performed by the German neurologist Heinrich O. Oppenheim (1858-1919) and the surgeon Fedor Krause (1857-1937); however, neither recognized the true pathological condition of discogenic nerve compression syndrome. With the landmark report in the New England Journal of Medicine in 1934, the two American surgeons William Jason Mixter (1880-1958) and Joseph Seaton Barr (1901-1963) finally clarified the pathomechanism of lumbar disc herniation and furthermore, propagated discectomy as the standard therapy. Since then interventions on intervertebral discs rapidly increased and the treatment options for lumbar disc surgery quickly evolved. The surgical procedures changed over time and were continuously being refined. In the late 1960s the surgical microscope was introduced for spinal surgery by the work of the famous neurosurgeon Mahmut Gazi Yasargil and his colleague Wolfhard Caspar and so-called microdiscectomy was introduced. Besides open discectomy other interventional techniques were developed to overcome the side effects of surgical procedures. In 1964 the American orthopedic surgeon Lyman Smith (1912-1991) introduced chemonucleolysis, a minimally invasive technique consisting only of a cannula and the proteolytic enzyme chymopapain, which is injected into the disc compartment to dissolve the displaced disc material. In 1975 the Japanese orthopedic

Tidal power plant. Antrieb zur Stromerzeugung in Ausnutzung von Ebbe und Flut

Energy Technology Data Exchange (ETDEWEB)

Krause, A

1978-11-09

The invention refers to a drive unit for electricity generation by using the ebb and flood tides and flowing inland water, where a pontoon in a basin causes a shaft to move by upward and downward movement due to the ebb and flood tides and two racks and two geared pinions. The rotation of the shaft is minimal. It is increased by double gearwheels (principle: corn on the chess board). The shaft is driven by a triple transmission via 7 double gearwheels. As the order of magnitude of the basin and pontoon are unlimited, maximum transmission of force is possible. The important characteristics of the novelty: 2 racks and 2 geared pinions on one shaft, the connecting rod is omitted; use in an engine or a compressor. A further characteristic of the invention is that the double gearwheels are accomodated in one gearbox from the shaft to the axle of the electricity generator.

Critical experiments supporting underwater storage of tightly packed configurations of spent fuel pins. Technical progress report, January 1-March 31, 1981

International Nuclear Information System (INIS)

Hoovler, G.S.; Baldwin, M.N.

1981-04-01

Critical experiments are in progress on arrays of 2 1/2% enriched UO 2 fuel pins simulating underwater pin storage of spent power reactor fuel. Pin storage refers to a spent fuel storage concept in which the fuel assemblies are dismantled and the fuel pins are tightly packed into specially designed canisters. These experiments are providing benchmark data with which to validate nuclear codes used to design spent fuel pin storage racks

Future of neutrino experiments

Indian Academy of Sciences (India)

them are under construction. The next generation double beta decay experiments are sensitive to the inverted mass hierarchy. In order to explore the normal mass hierarchy, the sensitivity of the experiments still needs to be improved substantially. For example, see [32] for more details of the double beta decay experiments.

Double-diffractive processes in high-resolution missing-mass experiments at the Tevatron

International Nuclear Information System (INIS)

Khoze, V.A.; Martin, A.D.

2001-01-01

We evaluate, in a model-independent way, the signal-to-background ratio for Higgs→b anti b detection in exclusive double-diffractive events at the Tevatron and the LHC. For the missing-mass approach to be able to identify the Higgs boson, it will be necessary to use a central jet detector and to tag b quark jets. The signal is predicted to be very small at the Tevatron, but observable at the LHC. However we note that the background, that is double-diffractive dijet production, may serve as a unique gluon factory. We also give estimates for the double-diffractive production of χ c and χ b mesons at the Tevatron. We emphasize that a high-resolution missing-mass measurement, on its own, is insufficient to identify rare processes. (orig.)

Expanded spent fuel storage project at Yankee Atomic Electric Plant

International Nuclear Information System (INIS)

Chin, S.L.

1980-01-01

A detailed discussion on the project at the Yankee Rowe power reactor for expanding the capacity of the at-reactor storage pool by building double-tier storage racks. Various alternatives for providing additional capacity were examined by the operators. Away-from-reactor alternatives included shipment to existing privately owned facilities, a regional independent storage facility, and transshipments to other New England nuclear power plant pools. At-reactor alternatives evaluated included a new pool modification of the existing structure and finally, modification of the spent fuel pit. The establishment of a federal policy precluding transshipment of spent fuel prohibited the use of off-site alternatives. The addition of another pool was too expensive. The possibility of modifying an existing on-site structure required a new safety evaluation by the regulatory group with significant cost and time delays. Therefore, the final alternative - utilizing the existing spent fuel pool with some modification - was chosen due to cost, licensing possibility, no transport requirements, and the fact that the factors involved were mainly under the control of the operator. Modification of the pool was accomplished in phases. In the first phase, a dam was installed in the center of the pool (after the spent fuel was moved to one end). In the second phase, the empty end of the pool was drained and lined with stainless steel and the double-tier rack supports were added. In the third phase, the pool was refilled and the dam was removed. Then the spent fuel was moved into the completed end. In the fourth phase, the dam was replaced and the empty part of the pool was drained. The liner and double-tier rack supports were installed, the pool was refilled, and the dam was removed.The project demonstrated that the modification of existing spent fuel fuel pools for handling double-tier fuel racks is a viable solution for increasing the storage capacity at the reactor

Double Layer Dynamics in a Collisionless Magnetoplasma

DEFF Research Database (Denmark)

Iizuka, S.; Michelsen, Poul; Juul Rasmussen, Jens

and propagation of a double layer. The period of the oscillations is determined by the propagation length of the double layer. The current is limited during the propagation of the double layer by a growing negative potential barrier formed on the low potential tail. Similar phenomena appear when a potential......An experimental investigation of the dynamics of double layers is presented. The experiments are performed in a Q-machine plasma and the double layers are generated by applying a positive step potential to a cold collector plate terminating the plasma column. The double layer is created...... at the grounded plasma source just after the pulse is applied and it propagates towards the collector with a speed around the ion acoustic speed. When the collector is biased positively, large oscillations are obserced in the plasma current. These oscillations are found to be related to a recurring formation...

The history of double tax conventions in Croatia

OpenAIRE

Hrvoje Arbutina; Nataša Žunić Kovačević

2014-01-01

After a short introduction, the authors briefly describe the national experience in handling the problems of international double taxation through double tax conventions. This chapter is divided according to stages in the history of double tax conventions identified. The authors analyse the goals of tax treaty policies in differentiated stages with a survey of the economic implications. Special focus is placed on inter-country influences and the impact on and of international institutions and...

Double Chooz

Energy Technology Data Exchange (ETDEWEB)

Buck, Christian [Max-Planck-Institut fuer Kernphysik, Saupfercheckweg 1, D-69117 Heidelberg (Germany)

2006-05-15

The goal of the Double Chooz reactor neutrino experiment is to search for the neutrino mixing parameter {theta}{sub 13}. Double Chooz will use two identical detectors at 150 m and 1.05 km distance from the reactor cores. The near detector is used to monitor the reactor {nu}-bar {sub e} flux while the second is dedicated to the search for a deviation from the expected (1/distance){sup 2} behavior. This two detector concept will allow a relative normalization systematic error of ca. 0.6 %. The expected sensitivity for sin{sup 2}2{theta}{sub 13} is then in the range 0.02 - 0.03 after three years of data taking. The antineutrinos will be detected in a liquid scintillator through the capture on protons followed by a gamma cascade, produced by the neutron capture on Gd.

Development of a lower extremity wearable exoskeleton with double compact elastic module: preliminary experiments

Directory of Open Access Journals (Sweden)

Y. Long

2017-08-01

Full Text Available In this paper, a double compact elastic module is designed and implemented in the lower extremity exoskeleton. The double compact elastic module is composed of two parts, i.e., physical human robot interaction (pHRI measurement and the elastic actuation system (EAS, which are called proximal elastic module (PEM and distal elastic module (DEM respectively. The PEM is used as the pHRI information collection device while the DEM is used as the compliance device. A novel compact parallelogram-like structure based torsional spring is designed and developed. An iterative finite element analysis (FEA based optimization process was conducted to find the optimal parameters in the search space. In the PEM, the designed torsional spring has an outer circle with a diameter of 60 mm and an inner hole with a diameter of 12 mm, while in the DEM, the torsional spring has the outer circle with a diameter of 80 mm and the inner circle with a diameter of 16 mm. The torsional spring in the PEM has a thickness of 5 mm and a weight of 60 g, while that in the DEM has a thickness of 10 mm and a weight of 80 g. The double compact elastic module prototype is embedded in the mechanical joint directly. Calibration experiments were conducted on those two elastic modules to obtain the linear torque versus angle characteristic. The calibration experimental results show that this torsional spring in the PEM has a stiffness of 60.2 Nm rad−1, which is capable of withstanding a maximum torque of 4 Nm, while that in the DEM has a stiffness of 80.2 Nm rad−1, which is capable of withstanding a maximum torque of 30 Nm. The experimental results and the simulation data show that the maximum resultant errors are 6 % for the PEM and 4 % for the DEM respectively. In this paper, an assumed regression algorithm is used to learn the human motion intent (HMI based on the pHRI collection. The HMI is defined as the angular position of the human limb joint. A

Ice shielding in the large scale GENIUS experiment for double beta decay and dark matter search

International Nuclear Information System (INIS)

Klapdor-Kleingrothaus, H.V.; Zdesenko, Yu.G.

1998-01-01

We suggest here the use of ice as shielding material in the large scale GENIUS experiment for the ultimate sensitive double beta decay and dark matter search. The idea is to pack a working volume of several tons of liquid nitrogen, which contains the ''naked'' Ge detectors, inside an ice shielding. Very thin plastic foil would be used in order to prevent leakage of the liquid nitrogen. Due to the excellent advantages of ice shielding (high purity and low cost, self-supporting ability, thermo-isolation and optical properties, safety) this could be another possible way of realization of the GENIUS project. (orig.)

Studies of the electron-impact double-ionisation process in magnesium using coincidence techniques

International Nuclear Information System (INIS)

Ford, M.J.

1998-01-01

This article will review recent measurements of the electron-impact double-ionisation of atomic magnesium. Results for the resonant Auger double-ionisation process with coincident detection of all three outgoing electrons, the (e, 3e) experiment, and for the direct double-ionisation process where only two outgoing electrons are detected, the (e, (3 -1)e) experiment, will be discussed. The results are analysed with reference to ionisation mechanisms and comparisons are made with calculated double-ionisation cross sections. Copyright (1998) CSIRO Australia

Experience with radioactivity releases

International Nuclear Information System (INIS)

Anderson, T.V.; Johnson, A.G.; Ringle, J.C.

1972-01-01

On December 11, 1970, the reactor top continuous air monitor (CAM) showed an increase in particulate air activity of an unusual nature. A check of the CAM filter with a multi-channel analyzer indicated that the majority of the activity was due to Cs-138 , Cs-139 , Rb-89 , and Rb-90 , which indicated a probable fuel element leak. The CAM filter was changed and rechecked several times, but the rubidium and cesium radionuclides were consistently identified. The procedure was followed by removing three fuel elements at a time. Since the CAM was the only instrument picking up radioactivity, it was used as the primary radiation monitor. During the search for the leaky fuel element, it was found that the element in position E-18 (triangle cut-out) was leaning against the top of the element in E-17. Particulate air activity originating from the rotating rack loading port on the reactor top was reported by OSU during the previous TRIGA Owner's Seminar. Short term relief can be obtained by inserting a standard CAM filter paper over the rotating rack loading tube opening, but this has not proved satisfactory for runs of one hour or longer. A simple filter system for the rotating rack was built, and is operated as part of the argon ventilation system. This appears to have solved the problem

The double Chooz hardware trigger system

Energy Technology Data Exchange (ETDEWEB)

Cucoanes, Andi; Beissel, Franz; Reinhold, Bernd; Roth, Stefan; Stahl, Achim; Wiebusch, Christopher [RWTH Aachen (Germany)

2008-07-01

The double Chooz neutrino experiment aims to improve the present knowledge on {theta}{sub 13} mixing angle using two similar detectors placed at {proportional_to}280 m and respectively 1 km from the Chooz power plant reactor cores. The detectors measure the disappearance of reactor antineutrinos. The hardware trigger has to be very efficient for antineutrinos as well as for various types of background events. The triggering condition is based on discriminated PMT sum signals and the multiplicity of groups of PMTs. The talk gives an outlook to the double Chooz experiment and explains the requirements of the trigger system. The resulting concept and its performance is shown as well as first results from a prototype system.

Analysis method for the search for neutrinoless double beta decay in the NEMO3 experiment: study of the background and first results

International Nuclear Information System (INIS)

Etienvre, A.I.

2003-04-01

The NEMO3 detector, installed in the Frejus Underground Laboratory, is dedicated to the study of neutrinoless double beta decay: the observation of this process would sign the massive and Majorana nature of neutrino. The experiment consists in very thin central source foils (the total mass is equal to 10 kg), a tracking detector made of drift cells operating in Geiger mode, a calorimeter made of plastic scintillators associated to photomultipliers, a coil producing a 30 gauss magnetic field and two shields, dedicated to the reduction of the γ-ray and neutron fluxes. In the first part, I describe the implications of several mechanisms, related to trilinear R-parity violation, on double beta decay. The second part is dedicated to a detailed study of the tracking detector of the experiment: after a description of the different working tests, I present the determination of the characteristics of the tracking reconstruction (transverse and longitudinal resolution, by Geiger cell and precision on vertex determination, charge recognition). The last part corresponds to the analysis of the data taken by the experiment. On the one hand, an upper limit on the Tl 208 activity of the sources has been determined: it is lower than 68 mBq/kg, at 90% of confidence level. On the other hand, I have developed and tested on these data a method in order to analyse the neutrinoless double beta decay signal; this method is based on a maximum of likelihood using all the available information. Using this method, I could determine a first and very preliminary upper limit on the effective mass of the neutrino. (author)

Double excitation of helium by 3 MeV proton impact: experiment and theory

Energy Technology Data Exchange (ETDEWEB)

Bordenave-Montesquieu, A.; Gleizes, A.; Moretto-Capelle, P.; Benoit-Cattin, P. (Toulouse-3 Univ., 31 (France). Centre de Physique Atomique); Andriamonje, S. (Bordeaux-1 Univ., 33 -Gradignan (France)); Martin, F. (Universidad Autonoma de Madrid (Spain). Dept. de Quimica); Salin, A. (Bordeaux-1 Univ., 33 - Talence (France))

1992-08-14

Doubly differential cross sections for the double excitation of helium by high velocity protons are measured and compared with the predictions of the first-order Born approximation. Preliminary experimental data for the shapes and intensities of the resonances 2s[sup 2] [sup 1]S, 2p[sup 2] [sup 1]D and 2s2p [sup 1]P have been obtained from high resolution electron spectra at 20[sup o], 90[sup o] and 150[sup o] for a proton energy of 3 MeV. Both experiment and theory show that the excitation of the [sup 1]P resonance largely exceeds the [sup 1]D and [sup 1]S ones at this collision velocity. The shape and emission yield of the [sup 1]P line is well described by theory over the whole angular range. The agreement for the other two resonances is not always satisfactory. (author).

Exploration of Pixelated detectors for double beta decay searches within the COBRA experiment

Energy Technology Data Exchange (ETDEWEB)

Schwenke, M., E-mail: schwenke@asp.tu-dresden.de [Institut fuer Kern- und Teilchenphysik, Technische Universitaet Dresden, Zellescher Weg 19, 01069 Dresden (Germany); Zuber, K.; Janutta, B. [Institut fuer Kern- und Teilchenphysik, Technische Universitaet Dresden, Zellescher Weg 19, 01069 Dresden (Germany); He, Z.; Zeng, F. [Department of Nuclear Engineering and Radiological Sciences, University of Michigan, Ann Arbor, Michigan 48109-2104 (United States); Anton, G.; Michel, T.; Durst, J.; Lueck, F.; Gleixner, T. [Erlangen Centre for Astroparticle Physics, Friedrich-Alexander-Universitaet Erlangen-Nuernberg, Erwin-Rommel-Str. 1, 91058 Erlangen (Germany); Goessling, C.; Schulz, O.; Koettig, T. [Technische Universitaet Dortmund, Physik E IV, 44221 Dortmund (Germany); Krawczynski, H.; Martin, J. [Department of Physics, Washington University in St. Louis, Campus Box 1105, One Brookings Drive, St. Louis, MO 63130-4899 (United States); Stekl, I.; Cermak, P. [Institute of Experimental and Applied Physics, Czech Technical University in Prague, Horska 3a/22, 128 00 Prague (Czech Republic)

2011-09-11

The aim of the COBRA experiment is the search for neutrinoless double beta decay events in Cadmium Zinc Telluride (CdZnTe) room temperature semiconductor detectors. The development of pixelated detectors provides the potential for clear event identification and thus major background reduction. The tracking option of a semiconductor is a unique approach in this field. For initial studies, several possible detector systems are considered with a special regard for low background applications: the large volume system Polaris with a pixelated CdZnTe sensor, Timepix detectors with Si and enriched CdTe sensor material and a CdZnTe pixel system developed at the Washington University in St. Louis, USA. For all detector systems first experimental background measurements taken at underground laboratories (Gran Sasso Underground Laboratory in Italy, LNGS and the Niederniveau Messlabor Felsenkeller in Dresden, Germany) and additionally for the Timepix detectors simulation results are presented.

Sodium-water reaction in double pool LMFBR, (5)

International Nuclear Information System (INIS)

Yoshida, Kazuo; Kumagai, Hiromichi; Nishi, Yoshihisa; Uotani, Masaki

1990-01-01

Experiments were conducted using a 1/5 scale model of the Double Pool in order to evaluate a pressure rise caused by a large scale sodium-water reaction. The experiments were focused on the pressure rise caused by the piston motion of liquid sodium. It appeared from the results that the magnitude of this pressure rise depends on the depth of reaction point, and that a pressure rise more than 1 MPa would arise in the real Double Pool plant. A new design of steam generator is proposed to mitigate the pressure rise. (author)

Characteristics of unsteady flow field and flow-induced noise for an axial cooling fan used in a rack mount server computer Characteristics of unsteady flow field and flow-induced noise for an axial cooling fan used in a rack mount server computer

Energy Technology Data Exchange (ETDEWEB)

Lim, Tae Gyun; Jeon, Wan Ho [Technical Research Lab., CEDIC Co., Seoul (Korea, Republic of); Minorikawa, Gaku [Dept. of f Mechanical Engineering, Faculty of Science and Engineering, Hosei University, Tokyo (Japan)

2016-10-15

The recent development of small and lightweight rack mount servers and computers has resulted in the decrease of the size of cooling fans. However, internal fans still need to achieve a high performance to release the heat generated from interior parts, and they should emit low noise. On the contrary, measurement data, such as flow properties and flow visualizations, cannot be obtained easily when cooling fans are small. Thus, a numerical analysis approach is necessary for the performance evaluation and noise reduction of small cooling fans. In this study, the noise of a small cooling fan used for computers or servers was measured and then compared with the aeroacoustic noise result based on a numerical analysis. Three-dimensional Navier-Stokes equations were solved to predict the unsteady flow field and surface pressure fluctuation according to the blades and casing surface used. The simplified Ffowcs Williams and Hawkings equation was used to predict aeroacoustic noise by assuming that a dipole is the major cause of fan noise. Results of the aeroacoustic noise analysis agreed well with that of the experiment, and a tonal noise whose frequency was lower than the first blade passing frequency could be identified in the noise spectrum. This phenomenon is caused by the shape of the bell mouth. A coherence analysis was performed to examine the correlation between the shape of the cooling fan and the noise.

Characteristics of unsteady flow field and flow-induced noise for an axial cooling fan used in a rack mount server computer Characteristics of unsteady flow field and flow-induced noise for an axial cooling fan used in a rack mount server computer

International Nuclear Information System (INIS)

Lim, Tae Gyun; Jeon, Wan Ho; Minorikawa, Gaku

2016-01-01

The recent development of small and lightweight rack mount servers and computers has resulted in the decrease of the size of cooling fans. However, internal fans still need to achieve a high performance to release the heat generated from interior parts, and they should emit low noise. On the contrary, measurement data, such as flow properties and flow visualizations, cannot be obtained easily when cooling fans are small. Thus, a numerical analysis approach is necessary for the performance evaluation and noise reduction of small cooling fans. In this study, the noise of a small cooling fan used for computers or servers was measured and then compared with the aeroacoustic noise result based on a numerical analysis. Three-dimensional Navier-Stokes equations were solved to predict the unsteady flow field and surface pressure fluctuation according to the blades and casing surface used. The simplified Ffowcs Williams and Hawkings equation was used to predict aeroacoustic noise by assuming that a dipole is the major cause of fan noise. Results of the aeroacoustic noise analysis agreed well with that of the experiment, and a tonal noise whose frequency was lower than the first blade passing frequency could be identified in the noise spectrum. This phenomenon is caused by the shape of the bell mouth. A coherence analysis was performed to examine the correlation between the shape of the cooling fan and the noise

Characterization of large-area photomultipliers under low magnetic fields: Design and performance of the magnetic shielding for the Double Chooz neutrino experiment

International Nuclear Information System (INIS)

Calvo, E.; Cerrada, M.; Fernandez-Bedoya, C.; Gil-Botella, I.; Palomares, C.; Rodriguez, I.; Toral, F.; Verdugo, A.

2010-01-01

A precise quantitative measurement of the effect of low magnetic fields in Hamamatsu R7081 photomultipliers has been performed. These large-area photomultipliers will be used in the Double Chooz neutrino experiment. A magnetic shielding has been developed for these photomultipliers. Its design and performance is also reported in this paper.

Main features of detectors and isotopes to investigate double beta decay with increased sensitivity

Science.gov (United States)

Barabash, A. S.

2018-03-01

The current situation in double beta decay experiments, the characteristics of modern detectors and the possibility of increasing the sensitivity to neutrino mass in future experiments are discussed. The issue of the production and use of enriched isotopes in double beta decay experiments is discussed in addition.

Experiment prediction for LOFT nuclear experiments L5-1/L8-2

International Nuclear Information System (INIS)

Chen, T.H.; Modro, S.M.

1982-01-01

The LOFT Experiments L5-1 and L8-2 simulated intermediate break loss-of-coolant accidents with core uncovery. This paper compares the predictions with the measured data for these experiments. The RELAP5 code was used to perform best estimate double-blind and single-blind predictions. The double-blind calculations are performed prior to the experiment and use specified nominal initial and boundary conditions. The single-blind calculations are performed after the experiment and use measured initial and boundary conditions while maintaining all other parameters constant, including the code version. Comparisons of calculated results with experimental results are discussed; the possible causes of discrepancies are explored and explained. RELAP5 calculated system pressure, mass inventory, and fuel cladding temperature agree reasonably well with the experiment results, and only slight changes are noted between the double-blind and single-blind predictions

OH spectroscopy with frequency-doubled dye laser radiation

Energy Technology Data Exchange (ETDEWEB)

ter Meulen, J J

1979-01-01

Discusses the excitation of the OH radical by UV radiation for the determination of the hyperfine structure of the excited states. The 307 nm UV light is obtained by doubling the frequency (in double-refraction crystals) of a tunable dye laser. Details of the laser set-up are given. The method is suitable for application to other high-resolution molecular spectroscopy experiments in the area between 200 and 400 nm. Further extensions can be expected with ring compound dyes and external doubling of the frequency.

Determination of the double-polarization observable E for the reaction γp→pπ0 in the CBELSA/TAPS experiment

International Nuclear Information System (INIS)

Gottschall, Manuela

2013-01-01

In the framework of this thesis the double-polarization observable E for the reaction γp→pπ 0 was determined in the energy range of E γ =600-2400 MeV. For this in the CBELSA/TAPS experiment ar the ELSA electron-stretcher facility a circularly polarized photon beam and a longitudinally polarized butanol target were available. Additionally for the determination of the dilution factor, which specifies the contribution of reactions on the hydrogen of the butanol, data were taken on a hydrogen target and a carbon target. In order to determine the double-polarization observable E two different methods were developed. in the first method exclusively the data on the butanol target were applied and the double-polarization observable E determined by means of the dilution factor. In the second method the sum from the cross sections at antiparallel and parallel spin orientation σ 1/2 and σ 3/2 was expressed by the unpolarized cross section 2σ, which was determined by means of the data on the unpolarized hydrogen target. The results of the double-polarization observable E were compared with the predictions of the three presently most usual partial-wave analyses. While the unpolarized cross section can be well described by all three predictions, already at lowest energies differences occur between the predictions and the data, so that by the extraction of this observable new informations for the partial-wave analyses can be made available.

Analysis method for the search for neutrinoless double beta decay in the NEMO3 experiment: study of the background and first results; Methode d'analyse pour la recherche de la double desintegration {beta} sans emission de neutrinos dans l'experience NEMO3. Etude du bruit de fond et premiers resultats

Energy Technology Data Exchange (ETDEWEB)

Etienvre, A I

2003-04-15

The NEMO3 detector, installed in the Frejus Underground Laboratory, is dedicated to the study of neutrinoless double beta decay: the observation of this process would sign the massive and Majorana nature of neutrino. The experiment consists in very thin central source foils (the total mass is equal to 10 kg), a tracking detector made of drift cells operating in Geiger mode, a calorimeter made of plastic scintillators associated to photomultipliers, a coil producing a 30 gauss magnetic field and two shields, dedicated to the reduction of the {gamma}-ray and neutron fluxes. In the first part, I describe the implications of several mechanisms, related to trilinear R-parity violation, on double beta decay. The second part is dedicated to a detailed study of the tracking detector of the experiment: after a description of the different working tests, I present the determination of the characteristics of the tracking reconstruction (transverse and longitudinal resolution, by Geiger cell and precision on vertex determination, charge recognition). The last part corresponds to the analysis of the data taken by the experiment. On the one hand, an upper limit on the Tl{sup 208} activity of the sources has been determined: it is lower than 68 mBq/kg, at 90% of confidence level. On the other hand, I have developed and tested on these data a method in order to analyse the neutrinoless double beta decay signal; this method is based on a maximum of likelihood using all the available information. Using this method, I could determine a first and very preliminary upper limit on the effective mass of the neutrino. (author)

Double hard scattering without double counting

Energy Technology Data Exchange (ETDEWEB)

Diehl, Markus [Deutsches Elektronen-Synchrotron (DESY), Hamburg (Germany); Gaunt, Jonathan R. [VU Univ. Amsterdam (Netherlands). NIKHEF Theory Group; Schoenwald, Kay [Deutsches Elektronen-Synchrotron (DESY), Zeuthen (Germany)

2017-02-15

Double parton scattering in proton-proton collisions includes kinematic regions in which two partons inside a proton originate from the perturbative splitting of a single parton. This leads to a double counting problem between single and double hard scattering. We present a solution to this problem, which allows for the definition of double parton distributions as operator matrix elements in a proton, and which can be used at higher orders in perturbation theory. We show how the evaluation of double hard scattering in this framework can provide a rough estimate for the size of the higher-order contributions to single hard scattering that are affected by double counting. In a numeric study, we identify situations in which these higher-order contributions must be explicitly calculated and included if one wants to attain an accuracy at which double hard scattering becomes relevant, and other situations where such contributions may be neglected.

Double hard scattering without double counting

International Nuclear Information System (INIS)

Diehl, Markus; Gaunt, Jonathan R.

2017-02-01

Double parton scattering in proton-proton collisions includes kinematic regions in which two partons inside a proton originate from the perturbative splitting of a single parton. This leads to a double counting problem between single and double hard scattering. We present a solution to this problem, which allows for the definition of double parton distributions as operator matrix elements in a proton, and which can be used at higher orders in perturbation theory. We show how the evaluation of double hard scattering in this framework can provide a rough estimate for the size of the higher-order contributions to single hard scattering that are affected by double counting. In a numeric study, we identify situations in which these higher-order contributions must be explicitly calculated and included if one wants to attain an accuracy at which double hard scattering becomes relevant, and other situations where such contributions may be neglected.

The 76Ge Program to Search for Neutrinoless Double-Beta Decay

Science.gov (United States)

Guiseppe, Vincente

2017-09-01

Neutrinoless double-beta decay searches play a major role in determining the nature of neutrinos, the existence of a lepton violating process, and the effective Majorana neutrino mass. The Majorana and Gerda Collaborations are operating arrays of high purity Ge detectors to search for neutrinoless double-beta decay in 76Ge. The Majorana Demonstrator is operating at the Sanford Underground Research Facility in South Dakota while the Gerda experiment is operating at LNGS in Italy. The Gerda and Majorana Demonstrator experiments have achieved the lowest backgrounds in the neutrinoless double-beta decay region of interest. These results, coupled with the superior energy resolution (0.1%) of Ge detectors demonstrate that 76Ge is an ideal isotope for a large next generation experiment. The LEGEND collaboration, with 220 members from 47 institutions around the world, has been formed to pursue a ton scale 76Ge experiment. Building on the successes of Gerda and Majorana, the LEGEND collaboration aims to develop a phased neutrinoless double-beta decay experimental program with discovery potential at a half-life significantly longer than 1027 years. This talk will present the initial results from the Majorana Demonstrator and Gerda experiments and the plan for the LEGEND program.

Experience of remote under water handling operations at Tarapur Atomic Power Station

International Nuclear Information System (INIS)

Agarwal, S.K.

1990-01-01

Each Refuelling outage of Tarapur Atomic Power Station Reactors involves a great deal of remote underwater handling operations using special remote handling tools, working deep down in the reactor vessel under about sixty feet of water and in the narrow confines of highly radioactive core. The remote underwater handling operations include incore and out of core sipping operations, fuel reloading or shuffling, uncoupling of control rod drives, replacement and shuffling of control blades, replacement of local power range monitors, spent fuel shipment in casks, retrieval of fallen or displaced fuel top guide spacers, orifices and their installation, underwater CCTV inspection of reactor internals, core verification, channelling and dechannelling of fuel bundles, inspection of fuel bundles and channels, unbolting and removal of old racks, installation of high density racks, removal and reinstallation of fuel support plugs and guide tubes, underwater cutting of irradiated hardware material and their disposal, fuel reconstitution, removal and reinstallation of system dryer separator etc.. The paper describes in brief the salient experience of remote underwater handling operations at TAPS especially the unusual problems faced and solved, by using special tools, employing specific techniques and by repeated efforts, patience, ingenuity and skills. (author). 10 figs

Neutron Interactions in the CUORE Neutrinoless Double Beta Decay Experiment

Energy Technology Data Exchange (ETDEWEB)

Dolinski, Michelle Jean [Univ. of California, Berkeley, CA (United States)

2008-10-01

Neutrinoless double beta decay (0vDBD) is a lepton-number violating process that can occur only for a massive Majorana neutrino. The search for 0vDBD is currently the only practical experimental way to determine whether neutrinos are identical to their own antiparticles (Majorana neutrinos) or have distinct particle and anti-particle states (Dirac neutrinos). In addition, the observation of 0vDBD can provide information about the absolute mass scale of the neutrino. The Cuoricino experiment was a sensitive search for 0vDBD, as well as a proof of principle for the next generation experiment, CUORE. CUORE will search for 0vDBD of ¹³⁰Te with a ton-scale array of unenriched TeO₂ bolometers. By increasing mass and decreasing the background for 0vDBD, the half-life sensitivity of CUORE will be a factor of twenty better than that of Cuoricino. The site for both of these experiments is the Laboratori Nazionali del Gran Sasso, an underground laboratory with 3300 meters water equivalent rock overburden and a cosmic ray muon attenuation factor of 10^-6. Because of the extreme low background requirements for CUORE, it is important that all potential sources of background in the 0vDBD peak region at 2530 keV are well understood. One potential source of background for CUORE comes from neutrons, which can be produced underground both by (α,n) reactions and by fast cosmic ray muon interactions. Preliminary simulations by the CUORE collaboration indicate that these backgrounds will be negligible for CUORE. However, in order to accurately simulate the expected neutron background, it is important to understand the cross sections for neutron interactions with detector materials. In order to help refine these simulations, I have measured the gamma-ray production cross sections for interactions of neutrons on the abundant stable isotopes of Te using the GEANIE detector array at the Los Alamos Neutron Science Center. In addition, I have used the GEANIE

Challenges in Double Beta Decay

Directory of Open Access Journals (Sweden)

Oliviero Cremonesi

2014-01-01

Full Text Available In the past ten years, neutrino oscillation experiments have provided the incontrovertible evidence that neutrinos mix and have finite masses. These results represent the strongest demonstration that the electroweak Standard Model is incomplete and that new Physics beyond it must exist. In this scenario, a unique role is played by the Neutrinoless Double Beta Decay searches which can probe lepton number conservation and investigate the Dirac/Majorana nature of the neutrinos and their absolute mass scale (hierarchy problem with unprecedented sensitivity. Today Neutrinoless Double Beta Decay faces a new era where large-scale experiments with a sensitivity approaching the so-called degenerate-hierarchy region are nearly ready to start and where the challenge for the next future is the construction of detectors characterized by a tonne-scale size and an incredibly low background. A number of new proposed projects took up this challenge. These are based either on large expansions of the present experiments or on new ideas to improve the technical performance and/or reduce the background contributions. In this paper, a review of the most relevant ongoing experiments is given. The most relevant parameters contributing to the experimental sensitivity are discussed and a critical comparison of the future projects is proposed.

The virtual double-slit experiment to High School level (Part I: behavior classical analysis (with bullets and waves and development of computational software

Directory of Open Access Journals (Sweden)

Danilo Cardoso Ferreira

2016-09-01

Full Text Available http://dx.doi.org/10.5007/2175-7941.2016v33n2p697   This paper analyses the double-slit virtual experiment and it composed of two parts: The part I covers the classical theory (with bullets and waves and the part II covers the interference with electrons or photons. Firstly, we have analyzed the same experiment that shoots a stream of bullets. In front of the gun we have a wall that has in it two holes just big enough to let a bullet through. Beyond the wall is a backstop (say a thick wall of wood which will absorb the bullets when they hit it. In this case, the probabilities just add together. The effect with both holes open is the sum of effects with each holes open alone. We have shown it for high school level. Next, we have analyzed a same experiment with water waves. The intensity observed when both holes are open is certainly not the sum of the intensity of the wave from hole 1 (which we find by measuring when hole 2 is blocked off and the intensity of the wave form hole 2 (seen when hole 1 is blocked. Finally, we have shown a software developed by students about double-slit experiment with bullets.

Experiment prediction for LOFT nuclear experiments L5-1 and L8-2

International Nuclear Information System (INIS)

Chen, T.H.; Modro, S.M.

1983-01-01

The LOFT Experiments L5-1 and L8-2 simulated intermediate break loss-of-coolant accidents with core uncovery. This paper compares the predictions with the measured data for these experiments. The RELAP5 code was used to perform best estimate double-blind and single-blind predictions. The double-blind calculations are performed prior to the experiment and use specified nominal initial and boundary conditions. The single-blind calculations are performed after the experiment and use measured initial and boundary conditions while maintaining all other parameters constant, including the code version. Comparisons of calculated results with experimental results are discussed; the possible causes of discrepancies are explored and explained. RELAP5 calculated system pressure, mass inventory, and fuel cladding temperature agree reasonably well with the experiment results, and only slight changes are noted between the double-blind and single-blind predictions

The Life Cycle Application of Intelligent Software Modeling for the First Materials Science Research Rack

Science.gov (United States)

Rice, Amanda; Parris, Frank; Nerren, Philip

2000-01-01

Marshall Space Flight Center (MSFC) has been funding development of intelligent software models to benefit payload ground operations for nearly a decade. Experience gained from simulator development and real-time monitoring and control is being applied to engineering design, testing, and operation of the First Material Science Research Rack (MSRR-1). MSRR-1 is the first rack in a suite of three racks comprising the Materials Science Research Facility (MSRF) which will operate on the International Space Station (ISS). The MSRF will accommodate advanced microgravity investigations in areas such as the fields of solidification of metals and alloys, thermo-physical properties of polymers, crystal growth studies of semiconductor materials, and research in ceramics and glasses. The MSRR-1 is a joint venture between NASA and the European Space Agency (ESA) to study the behavior of different materials during high temperature processing in a low gravity environment. The planned MSRR-1 mission duration is five (5) years on-orbit and the total design life is ten (IO) years. The MSRR-1 launch is scheduled on the third Utilization Flight (UF-3) to ISS, currently in February of 2003). The objective of MSRR-1 is to provide an early capability on the ISS to conduct material science, materials technology, and space product research investigations in microgravity. It will provide a modular, multi-user facility for microgravity research in materials crystal growth and solidification. An intelligent software model of MSRR-1 is under development and will serve multiple purposes to support the engineering analysis, testing, training, and operational phases of the MSRR-1 life cycle development. The G2 real-time expert system software environment developed by Gensym Corporation was selected as the intelligent system shell for this development work based on past experience gained and the effectiveness of the programming environment. Our approach of multi- uses of the simulation model and

Microscope-Based Fluid Physics Experiments in the Fluids and Combustion Facility on ISS

Science.gov (United States)

Doherty, Michael P.; Motil, Susan M.; Snead, John H.; Malarik, Diane C.

2000-01-01

At the NASA Glenn Research Center, the Microgravity Science Program is planning to conduct a large number of experiments on the International Space Station in both the Fluid Physics and Combustion Science disciplines, and is developing flight experiment hardware for use within the International Space Station's Fluids and Combustion Facility. Four fluids physics experiments that require an optical microscope will be sequentially conducted within a subrack payload to the Fluids Integrated Rack of the Fluids and Combustion Facility called the Light Microscopy Module, which will provide the containment, changeout, and diagnostic capabilities to perform the experiments. The Light Microscopy Module is planned as a fully remotely controllable on-orbit microscope facility, allowing flexible scheduling and control of experiments within International Space Station resources. This paper will focus on the four microscope-based experiments, specifically, their objectives and the sample cell and instrument hardware to accommodate their requirements.

High-throughput flow injection analysis mass spectroscopy with networked delivery of color-rendered results. 2. Three-dimensional spectral mapping of 96-well combinatorial chemistry racks.

Science.gov (United States)

Görlach, E; Richmond, R; Lewis, I

1998-08-01

For the last two years, the mass spectroscopy section of the Novartis Pharma Research Core Technology group has analyzed tens of thousands of multiple parallel synthesis samples from the Novartis Pharma Combinatorial Chemistry program, using an in-house developed automated high-throughput flow injection analysis electrospray ionization mass spectroscopy system. The electrospray spectra of these samples reflect the many structures present after the cleavage step from the solid support. The overall success of the sequential synthesis is mirrored in the purity of the expected end product, but the partial success of individual synthesis steps is evident in the impurities in the mass spectrum. However this latter reaction information, which is of considerable utility to the combinatorial chemist, is effectively hidden from view by the very large number of analyzed samples. This information is now revealed at the workbench of the combinatorial chemist by a novel three-dimensional display of each rack's complete mass spectral ion current using the in-house RackViewer Visual Basic application. Colorization of "forbidden loss" and "forbidden gas-adduct" zones, normalization to expected monoisotopic molecular weight, colorization of ionization intensity, and sorting by row or column were used in combination to highlight systematic patterns in the mass spectroscopy data.

Effects of Inlet Modification and Rocket-Rack Extension on the Longitudinal Trim and Low-Lift Drag of the Douglas F5D-1 Airplane as Obtained with a 0.125-Scale Rocket-Boosted Model between Mach Numbers of 0.81 and 1.64, TED No. NACA AD 399

Science.gov (United States)

Hastings, Earl C., Jr.; Dickens, Waldo L.

1957-01-01

A flight investigation was conducted to determine the effects of an inlet modification and rocket-rack extension on the longitudinal trim and low-lift drag of the Douglas F5D-1 airplane. The investigation was conducted with a 0.125-scale rocket-boosted model which was flight tested at the Langley Pilotless Aircraft Research Station at Wallops Island, Va. Results indicate that the combined effects of the modified inlet and fully extended rocket racks on the trim lift coefficient and trim angle of attack were small between Mach numbers of 0.94 and 1.57. Between Mach numbers of 1.10 and 1.57 there was an average increase in drag coefficient of about o,005 for the model with modified inlet and extended rocket racks. The change in drag coefficient due to the inlet modification alone is small between Mach numbers of 1.59 and 1.64

Routine digital pathology workflow: The Catania experience

Directory of Open Access Journals (Sweden)

Filippo Fraggetta

2017-01-01

Full Text Available Introduction: Successful implementation of whole slide imaging (WSI for routine clinical practice has been accomplished in only a few pathology laboratories worldwide. We report the transition to an effective and complete digital surgical pathology workflow in the pathology laboratory at Cannizzaro Hospital in Catania, Italy. Methods: All (100% permanent histopathology glass slides were digitized at ×20 using Aperio AT2 scanners. Compatible stain and scanning slide racks were employed to streamline operations. eSlide Manager software was bidirectionally interfaced with the anatomic pathology laboratory information system. Virtual slide trays connected to the two-dimensional (2D barcode tracking system allowed pathologists to confirm that they were correctly assigned slides and that all tissues on these glass slides were scanned. Results: Over 115,000 glass slides were digitized with a scan fail rate of around 1%. Drying glass slides before scanning minimized them sticking to scanner racks. Implementation required introduction of a 2D barcode tracking system and modification of histology workflow processes. Conclusion: Our experience indicates that effective adoption of WSI for primary diagnostic use was more dependent on optimizing preimaging variables and integration with the laboratory information system than on information technology infrastructure and ensuring pathologist buy-in. Implementation of digital pathology for routine practice not only leveraged the benefits of digital imaging but also creates an opportunity for establishing standardization of workflow processes in the pathology laboratory.

Neutrino oscillations with the OPERA experiment

CERN Document Server

Galati, Giuliana

2016-01-01

OPERA (Oscillation Project with Emulsion tRacking Apparatus) was a long-baseline experiment at the Gran Sasso laboratory (LNGS) designed to search for ν μ → ν τ oscillations in appearance mode. OPERA took data from 2008 to 2012 with the CNGS neutrino beam from CERN. The observation of five ν τ candidates allowed assessing the discovery of ν μ → ν τ appearance in the CNGS neutrino beam with a significance of 5 . 1 σ . The data analysis is still ongoing, with the goal of improving the sensitivity to the sterile neutrino search in the ν μ → ν τ and ν μ → ν e appearance channels and oscillation parameters with reduced statistical uncertainties. Current results will be presented and perspectives discussed.

Analysis method for the search for neutrinoless double beta decay in the NEMO3 experiment: study of the background and first results; Methode d'analyse pour la recherche de la double desintegration {beta} sans emission de neutrinos dans l'experience NEMO3. Etude du bruit de fond et premiers resultats

Energy Technology Data Exchange (ETDEWEB)

Etienvre, A.I

2003-04-15

The NEMO3 detector, installed in the Frejus Underground Laboratory, is dedicated to the study of neutrinoless double beta decay: the observation of this process would sign the massive and Majorana nature of neutrino. The experiment consists in very thin central source foils (the total mass is equal to 10 kg), a tracking detector made of drift cells operating in Geiger mode, a calorimeter made of plastic scintillators associated to photomultipliers, a coil producing a 30 gauss magnetic field and two shields, dedicated to the reduction of the {gamma}-ray and neutron fluxes. In the first part, I describe the implications of several mechanisms, related to trilinear R-parity violation, on double beta decay. The second part is dedicated to a detailed study of the tracking detector of the experiment: after a description of the different working tests, I present the determination of the characteristics of the tracking reconstruction (transverse and longitudinal resolution, by Geiger cell and precision on vertex determination, charge recognition). The last part corresponds to the analysis of the data taken by the experiment. On the one hand, an upper limit on the Tl{sup 208} activity of the sources has been determined: it is lower than 68 mBq/kg, at 90% of confidence level. On the other hand, I have developed and tested on these data a method in order to analyse the neutrinoless double beta decay signal; this method is based on a maximum of likelihood using all the available information. Using this method, I could determine a first and very preliminary upper limit on the effective mass of the neutrino. (author)

Double beta decay searches with thermal detectors

International Nuclear Information System (INIS)

Pirro, Stefano

2006-01-01

Double beta decay searches have become more and more important in the last few years. The 'second generation' experiments will allow to explore the inverse hierarchy region but, due to the uncertainties in the nuclear matrix elements, none of them will be able to cover completely the allowed region. Thus the need to investigate different DBD emitters becomes more important. The bolometric technique is only one able to study different nuclei with the proper energy resolution, key point for the future experiments. The possibility to reject the natural background arising from fast neutrons and alpha particles was recently directly proved with thermal bolometers, using the double read out (heat and scintillation). This new technique offers the possibility to reach background levels two orders of magnitude smaller with respect to the ones of the next planned experiments, aiming the possibility to investigate direct hierarchy region. (author)

Status of the CUORE and results from the CUORE-0 neutrinoless double beta decay experiments

Science.gov (United States)

Sisti, M.; Artusa, D. R.; Avignone, F. T.; Azzolini, O.; Balata, M.; Banks, T. I.; Bari, G.; Beeman, J.; Bellini, F.; Bersani, A.; Biassoni, M.; Brofferio, C.; Bucci, C.; Cai, X. Z.; Camacho, A.; Caminata, A.; Canonica, L.; Cao, X. G.; Capelli, S.; Cappelli, L.; Carbone, L.; Cardani, L.; Casali, N.; Cassina, L.; Chiesa, D.; Chott, N.; Clemenza, M.; Copello, S.; Cosmelli, C.; Cremonesi, O.; Creswick, R. J.; Cushman, J. S.; Dafinei, I.; Dally, A.; Datskov, V.; Dell'Oro, S.; Deninno, M. M.; Di Domizio, S.; di Vacri, M. L.; Drobizhev, A.; Ejzak, L.; Fang, D. Q.; Farach, H. A.; Faverzani, M.; Fernandes, G.; Ferri, E.; Ferroni, F.; Fiorini, E.; Franceschi, M. A.; Freedman, S. J.; Fujikawa, B. K.; Giachero, A.; Gironi, L.; Giuliani, A.; Gorla, P.; Gotti, C.; Gutierrez, T. D.; Haller, E. E.; Han, K.; Heeger, K. M.; Hennings-Yeomans, R.; Hickerson, K. P.; Huang, H. Z.; Kadel, R.; Keppel, G.; Kolomensky, Yu. G.; Li, Y. L.; Ligi, C.; Lim, K. E.; Liu, X.; Ma, Y. G.; Maiano, C.; Maino, M.; Martinez, M.; Maruyama, R. H.; Mei, Y.; Moggi, N.; Morganti, S.; Napolitano, T.; Nastasi, M.; Nisi, S.; Nones, C.; Norman, E. B.; Nucciotti, A.; O'Donnell, T.; Orio, F.; Orlandi, D.; Ouellet, J. L.; Pagliarone, C. E.; Pallavicini, M.; Palmieri, V.; Pattavina, L.; Pavan, M.; Pedretti, M.; Pessina, G.; Pettinacci, V.; Piperno, G.; Pira, C.; Pirro, S.; Pozzi, S.; Previtali, E.; Rosenfeld, C.; Rusconi, C.; Sala, E.; Sangiorgio, S.; Scielzo, N. D.; Smith, A. R.; Taffarello, L.; Tenconi, M.; Terranova, F.; Tian, W. D.; Tomei, C.; Trentalange, S.; Ventura, G.; Vignati, M.; Wang, B. S.; Wang, H. W.; Wielgus, L.; Wilson, J.; Winslow, L. A.; Wise, T.; Woodcraft, A.; Zanotti, L.; Zarra, C.; Zhang, G. Q.; Zhu, B. X.; Zucchelli, S.

2016-04-01

CUORE is a 741 kg array of TeO2 bolometers for the search of neutrinoless double beta decay of 130Te. The detector is being constructed at the Laboratori Nazionali del Gran Sasso, Italy, where it will start taking data in 2015. If the target background of 0.01 counts / (keV ṡkg ṡy) will be reached, in five years of data taking CUORE will have a 1σ half life sensitivity of 1026 y. CUORE-0 is a smaller experiment constructed to test and demonstrate the performances expected for CUORE. The detector is a single tower of 52 CUORE-like bolometers that started taking data in spring 2013. The status and perspectives of CUORE will be discussed, and the first CUORE-0 data will be presented.

Doubles everywhere: literary contributions to the study of the bodily self.

Science.gov (United States)

Dieguez, Sebastian

2013-01-01

The topic of the double is a hallmark of romantic, gothic, and fantastic literature. In the guise of the second self, the alter ego or the doppelgänger, fictional doubles have long fascinated critics, clinicians, and scientists. We review classical approaches to the theme and propose a broad clinical and neurocognitive framework from which to examine major instances of the motif in literature. Based on neurological disorders of the bodily self (including unilateral and whole body illusions and duplications), as well as related experimental approaches, we provide examples of literary depictions of bodily fragmentation and splitting; autoscopic hallucinations; the classical doppelgänger, second self, or heautoscopic double; the feeling of a presence; out-of-body experiences; and so-called near-death experiences. Examples include works from Guy de Maupassant, E.T.A. Hoffman, Edgar Allan Poe, Robert Louis Stevenson, Fyodor Dostoevsky, Rudyard Kipling, and others. We discuss these literary cases of doubles from a neurocognitive perspective, and suggest that common mechanisms of the bodily self are involved in the emergence of pathological illusory doubles, literary creations of the double, as well as widespread cultural and religious beliefs about the existence of doubles and the soul. Copyright © 2013 S. Karger AG, Basel.

The history of double tax conventions in Croatia

Directory of Open Access Journals (Sweden)

Hrvoje Arbutina

2014-06-01

Full Text Available After a short introduction, the authors briefly describe the national experience in handling the problems of international double taxation through double tax conventions. This chapter is divided according to stages in the history of double tax conventions identified. The authors analyse the goals of tax treaty policies in differentiated stages with a survey of the economic implications. Special focus is placed on inter-country influences and the impact on and of international institutions and organisations through an examination of the influence of bilateral tax treaties on model tax conventions and vice versa. The fifth chapter presents concluding observations.

Ac-induced disruption of the doubleDs structure in tomato

NARCIS (Netherlands)

Rommens, Caius M.T.; Biezen, Erik A. van der; Ouwerkerk, Pieter B.F.; Nijkamp, H. John J.; Hille, Jacques

1991-01-01

The maize doubleDs element is stably maintained in the tomato genome. Upon the subsequent introduction of Ac into a plant containing doubleDs, disruption of the doubleDs structure and DNA rearrangements at the site of the doubleDs element were observed. No indications were obtained for excision of

Simple and double two-colour photoionization of rare gas atoms

International Nuclear Information System (INIS)

Guyetand, O.

2008-05-01

The present work deals with simple and double ionization of rare gases by harmonic radiation produced by, and combined with, an intense femtosecond infrared laser. Technical aspects related to the use of harmonic generation and to the detection of ions and electrons in coincidence are exposed. Theoretical background for two colour, few-photon, single and double ionization is detailed. Spectra and angular distributions of the photoelectrons measured in helium are described and compared with TDSE (time-dependent Schroedinger equation) theoretical calculations, for various conditions of the harmonic photons. The shape of the angular distributions can be explained within the frame of two distinct analytic approaches: the perturbation theory and the soft-photon approximation. The double ionization measurements have been performed on xenon, a complex atom characterized by many possible routes leading to double ionization. The analysis of energy and angular correlations of the two photoelectrons proves the feasibility of such experiments that combines harmonic and infrared radiations. It shows that two step processes are dominant in the case of xenon. This work appeals for extending few-photon, double ionization experiments to lighter rare gases. (author)

Critical experiments supporting underwater storage of tightly packed configurations of spent fuel rods

International Nuclear Information System (INIS)

Hoovler, G.S.; Baldwin, M.N.

1981-04-01

Criticla arrays of 2.5%-enriched UO 2 fuel rods that simulate underwater rod storage of spent power reactor fuel are being constructed. Rod storage is a term used to describe a spent fuel storage concept in which the fuel bundles are disassembled and the rods are packed into specially designed cannisters. Rod storage would substantially increase the amount of fuel that could be stored in available space. These experiments are providing criticality data against which to benchmark nuclear codes used to design tightly packed rod storage racks

The MAJORANA DEMONSTRATOR Neutrinoless Double-Beta Decay Experiment

Directory of Open Access Journals (Sweden)

N. Abgrall

2014-01-01

Full Text Available The Majorana Demonstrator will search for the neutrinoless double-beta (ββ0ν decay of the isotope Ge with a mixed array of enriched and natural germanium detectors. The observation of this rare decay would indicate that the neutrino is its own antiparticle, demonstrate that lepton number is not conserved, and provide information on the absolute mass scale of the neutrino. The Demonstrator is being assembled at the 4850-foot level of the Sanford Underground Research Facility in Lead, South Dakota. The array will be situated in a low-background environment and surrounded by passive and active shielding. Here we describe the science goals of the Demonstrator and the details of its design.

Generation mechanism and properties of plasma double layers

International Nuclear Information System (INIS)

Sanduloviciu, M.; Lozneanu, E.

1985-01-01

The generation mechanism of plasma double layers is studied surveying the results of some experiments. The main mechanism is the same in the cases of collisional and collisionless plasmas. Inelastic quantum collision processes taking place between plasma electrons, accelerated in a local field up to near the same oriented velocity and the neutral particles of the background gases create the necessary conditions for double layer formation. (D.Gy.)

The gravitational plant physiology facility-Description of equipment developed for biological research in spacelab

Science.gov (United States)

Heathcote, D. G.; Chapman, D. K.; Brown, A. H.; Lewis, R. F.

1994-01-01

In January 1992, the NASA Suttle mission STS 42 carried a facility designed to perform experiments on plant gravi- and photo-tropic responses. This equipment, the Gravitational Plant Physiology Facility (GPPF) was made up of a number of interconnected units mounted within a Spacelab double rack. The details of these units and the plant growth containers designed for use in GPPF are described. The equipment functioned well during the mission and returned a substantial body of time-lapse video data on plant responses to tropistic stimuli under conditions of orbital microgravity. GPPF is maintained by NASA Ames Research Center, and is flight qualifiable for future spacelab missions.

Double tracks test site characterization report

International Nuclear Information System (INIS)

1996-05-01

This report presents the results of site characterization activities performed at the Double Tracks Test Site, located on Range 71 North, of the Nellis Air Force Range (NAFR) in southern Nevada. Site characterization activities included reviewing historical data from the Double Tracks experiment, previous site investigation efforts, and recent site characterization data. The most recent site characterization activities were conducted in support of an interim corrective action to remediate the Double Tracks Test Site to an acceptable risk to human health and the environment. Site characterization was performed using a phased approach. First, previously collected data and historical records sere compiled and reviewed. Generalized scopes of work were then prepared to fill known data gaps. Field activities were conducted and the collected data were then reviewed to determine whether data gaps were filled and whether other areas needed to be investigated. Additional field efforts were then conducted, as required, to adequately characterize the site. Characterization of the Double Tracks Test Site was conducted in accordance with the US Department of Energy's (DOE) Streamlined Approach for Environmental Restoration (SAFER)

The Majorana Demonstrator: Progress towards showing the feasibility of a tonne-scale 76Ge neutrinoless double-beta decay experiment

Science.gov (United States)

Finnerty, P.; Aguayo, E.; Amman, M.; Avignone, F. T., Iii; Barabash, A. S.; Barton, P. J.; Beene, J. R.; Bertrand, F. E.; Boswell, M.; Brudanin, V.; Busch, M.; Chan, Y.-D.; Christofferson, C. D.; Collar, J. I.; Combs, D. C.; Cooper, R. J.; Detwiler, J. A.; Doe, P. J.; Efremenko, Yu; Egorov, V.; Ejiri, H.; Elliott, S. R.; Esterline, J.; Fast, J. E.; Fields, N.; Fraenkle, F. M.; Galindo-Uribarri, A.; Gehman, V. M.; Giovanetti, G. K.; Green, M. P.; Guiseppe, V. E.; Gusey, K.; Hallin, A. L.; Hazama, R.; Henning, R.; Hoppe, E. W.; Horton, M.; Howard, S.; Howe, M. A.; Johnson, R. A.; Keeter, K. J.; Kidd, M. F.; Knecht, A.; Kochetov, O.; Konovalov, S. I.; Kouzes, R. T.; LaFerriere, B. D.; Leon, J.; Leviner, L. E.; Loach, J. C.; Luke, P. N.; MacMullin, S.; Marino, M. G.; Martin, R. D.; Merriman, J. H.; Miller, M. L.; Mizouni, L.; Nomachi, M.; Orrell, J. L.; Overman, N. R.; Perumpilly, G.; Phillips, D. G., Ii; Poon, A. W. P.; Radford, D. C.; Rielage, K.; Robertson, R. G. H.; Ronquest, M. C.; Schubert, A. G.; Shima, T.; Shirchenko, M.; Snavely, K. J.; Steele, D.; Strain, J.; Timkin, V.; Tornow, W.; Varner, R. L.; Vetter, K.; Vorren, K.; Wilkerson, J. F.; Yakushev, E.; Yaver, H.; Young, A. R.; Yu, C.-H.; Yumatov, V.; Majorana Collaboration

2014-03-01

The Majorana Demonstrator will search for the neutrinoless double-beta decay (0vββ) of the 76Ge isotope with a mixed array of enriched and natural germanium detectors. The observation of this rare decay would indicate the neutrino is its own anti-particle, demonstrate that lepton number is not conserved, and provide information on the absolute mass-scale of the neutrino. The Demonstrator is being assembled at the 4850 foot level of the Sanford Underground Research Facility in Lead, South Dakota. The array will be contained in a low-background environment and surrounded by passive and active shielding. The goals for the Demonstrator are: demonstrating a background rate less than 3 t-1 y-1 in the 4 keV region of interest (ROI) surrounding the 2039 keV 76Ge endpoint energy; establishing the technology required to build a tonne-scale germanium based double-beta decay experiment; testing the recent claim of observation of 0vββ [1]; and performing a direct search for light WIMPs (3-10 GeV/c2).

The search for Majorana neutrinos with neutrinoless double beta decays: From CUORICINO to LUCIFER experiment

Energy Technology Data Exchange (ETDEWEB)

Bellini, F. [Dipartimento di Fisica, Sapienza Universita di Roma, Roma I-00185 (Italy) and INFN - Sezione di Roma, Roma I-00185 (Italy)

2012-11-20

The study of neutrino properties is one of the fundamental challenges in particle physics nowadays. Fifty years of investigations established that neutrinos are massive but the absolute mass scale has not yet been measured. Moreover its true nature is still unknown. Is the neutrino its own antiparticle (thus violating the lepton number) as proposed by Majorana in 1937? The only way to probe the neutrino nature is through the observation of Neutrinoless Double Beta Decay (0{nu}{beta}{beta}), a very rare spontaneous nuclear transition which emits two electrons and no neutrinos. In this paper, after a brief introduction to the theoretical framework of Majorana's neutrino, a presentation of experimental challenges posed by 0{nu}{beta}{beta} search will be given as well as an overview of present status and future perpectives of experiments.

Experimental research of double-pulse linear induction electron accelerator

International Nuclear Information System (INIS)

Liao Shuqing; Cheng Cheng; Zheng Shuxin; Tang Chuanxiang; Lin Yuzheng; Jing Xiaobing; Mu Fan; Pan Haifeng

2009-01-01

The Mini-LIA is a double-pulse linear induction electron accelerator with megahertz repetition rates, which consists of a double-pulse power system, a thermal cathode electron gun, two induction cells, beam transportation systems and diagnosis systems, etc. Experiments of the Mini-LIA have been conducted. The double-pulse high voltage was obtained with several hundred nanosecond pulse intervals (i. e. megahertz repetition rate) and each pulse had an 80 kV amplitude with a FWHM of 80 ns. In the gap of the induction cell, the double-pulse accelerating electric field was measured via E-field probes, and the double-pulse electron beam with a current about 1.1 A has been obtained at the Mini-LIA exit. These experimental results show that the double-pulse high voltage with megahertz repetition rates can be generated by an insulation and junction system. And they also indicate that the induction cell with metglas as the ferromagnetic material and the LaB 6 thermal cathode electron gun suit the double-pulse operation with megahertz repetition rates. (authors)

Double Chooz and non Asian efforts towards {theta}{sub 13}

Energy Technology Data Exchange (ETDEWEB)

Lasserre, Thierry [CEA/Saclay and Laboratoire Astroparticle and Cosmologie Institut de Recherche des Lois Fondamentales de l' Univers Service de Physique des Particules 91191 Gif-s-Yvette (France)], E-mail: thierry.lasserre@cea.fr

2008-11-01

Neutrino oscillation physics is entering a precision measurement area. The smallness of the {theta}{sub 13} neutrino mixing angle is still enigmatic and should be resolved. Double Chooz will use two identical detectors near the Chooz nuclear power station to search for a non vanishing {theta}{sub 13}, and hopefully open the way to experiments aspiring to discover CP violation in the leptonic sector. The Angra project aims to prevail over the Double Chooz experiment if the third neutrino oscillation channel is not discovered in the forthcoming years.

Single-particle thermal diffusion of charged colloids: Double-layer theory in a temperature gradient

NARCIS (Netherlands)

Dhont, J.K.G.; Briels, Willem J.

2008-01-01

The double-layer contribution to the single-particle thermal diffusion coefficient of charged, spherical colloids with arbitrary double-layer thickness is calculated and compared to experiments. The calculation is based on an extension of the Debye-Hückel theory for the double-layer structure that

Calculation of the external dose rate in the spent fuel pool for the case to use compact racks

International Nuclear Information System (INIS)

Passos, E.M. dos; Alves, A.S.M.

1988-01-01

The possible introduction of compact racks in the spent fuel pool of the Angra 1 Nuclear Power Plant largely inreases its storage capacity, but originates an increase of the gamma radiation sources. The precise evaluation of the effects of the adoption of this option on the external gamma dose rates and also on the thickness of the concrete shielding requires the utilization of sofisticated computer codes (QAD, ANISN), which allow the calculation of the gamma dose rates through thick shielding walls. This paper describes the utilized methodology for the calculation of the modified pool shieldings, showing the obtained results for the Angra 1 NPP case. The gamma dose rate was calculated with the point Kernel model, first analytically, and later through utilization of the tridimensional multigroup QAD computer code. (author) [pt

Formation of double-{Lambda} hypernuclei at PANDA

Energy Technology Data Exchange (ETDEWEB)

Gaitanos, T., E-mail: Theodoros.Gaitanos@theo.physik.uni-giessen.de [Institut fuer Theoretische Physik, Universitaet Giessen, D-35392, Giessen (Germany); Larionov, A.B.; Lenske, H.; Mosel, U. [Institut fuer Theoretische Physik, Universitaet Giessen, D-35392, Giessen (Germany)

2012-05-01

We study the formation of single- and double-{Lambda} hypernuclei in antiproton-induced reactions relevant for the forthcoming PANDA experiment at FAIR. We use the Giessen Boltzmann-Uehling-Uhlenbeck (GiBUU) transport model with relativistic mean-fields for the description of non-equilibrium dynamics and the statistical multifragmentation model (SMM) for fragment formation. This combined approach describes the dynamical properties of strangeness and fragments in low energy p{sup Macron}-induced reactions fairly well. We then focus on the formation of double-{Lambda} hypernuclei in high energy p{sup Macron}-nucleus collisions on a primary target including the complementary {Xi}-induced reactions to a secondary one, as proposed by the PANDA Collaboration. Our results show that a copious production of double-{Lambda} hyperfragments is possible at PANDA. In particular, we provide first theoretical estimations on the double-{Lambda} production cross section, which strongly rises with decreasing energy of the secondary {Xi}-beam.

Nuclear transparency and double beta decay of molybdenum 100

International Nuclear Information System (INIS)

Nicholson, H.W.

1992-08-01

Data taking is now complete on a double beta decay experiment which has been carried out with collaborators from the Lawrence Berkeley Laboratory, the University of New Mexico, and the Idaho National Engineering Laboratory, and work is continuing on a second collaborative experiment, AGS experiment 850 at the Brookhaven National Laboratory to study nuclear color transparency. In March, the experimental apparatus used to search for double beta decay in molybdenum 100 in the Consil silver mine in Osburn, Idaho was dismantled, and the data analysis is in its final stages. No evidence has been seen for the O + → O + mode of zero neutrino double beta decay collaborators with a 1σ lifetime limit of 3 x 10 22 years. This limit is 7.5 times greater than the limit we published previously in Physical Review Letters in 1989. Backgrounds have been simulated and fits are currently underway to a simulated O + → 2 + mode of zero neutrino double beta decay to improve on a very preliminary 1σ lifetime limit of 2.3 x 10 21 years presented at the April, 1992 meeting of the APS in Washington. A scintillating fiber detector with three Hamamatsu, H4140, 256 channel multianode phototubes has been built, instrumented, and tested in the May--July 1992 run in the EVA detector at Brookhaven Laboratory's AGS. Preliminary results from this detector have been disappointing. it is likely that the detector will have to be substantially redesigned before the 1993 AGS run

Optimal operation of a south double-skin facade

Energy Technology Data Exchange (ETDEWEB)

Gratia, E.; De Herde, A. [Universite Catholique de Louvain (Belgium). Architecture et Climat

2004-01-01

There is an increasing demand for higher quality office buildings. Occupants and developers of office buildings ask for a healthy and stimulating working environment. Double-skin facades are appropriate when buildings are subject to great external noise and wind loads. A further area of application is in rehabilitation work, when existing facades cannot be renewed, or where this is not desirable. Double-skin facades have a special esthetic of their own, and this can be exploited architecturally to great advantage. However there are still relatively few buildings in which double-skin facades have actually been realized, and there is still too little experience of their behaviour in operation. In this matter, we choose to study a multi-storey double-skin facades behaviour. Simulations were realized with TAS software on the building proposed in the frame of the subtask A of the Task 27 (performance of solar facade components) of the International Energy Agency. Simulations were performed on the chosen building with and without double-skin facades. We decide to study eight types of days; and we analyze the double-skin facade behaviour for various operations. The thermal behaviours of the building with and without double-skin are compared. The study of these eight cases showed the importance of the dynamic use of the double-skin. The operation of this one must be obligatorily related to the climatic conditions as well external as interior and a bad operation of the double-skin could lead to catastrophic results. (author)

A double standard when group members behave badly: transgression credit to ingroup leaders.

Science.gov (United States)