WorldWideScience

Sample records for existing breakaway structures

  1. Breakaway frictions of dynamic O-rings in mechanical seals

    Science.gov (United States)

    Lai, Tom; Kay, Peter

    1993-05-01

    Breakaway friction of a dynamic O-ring affects the mechanical seal's response to large axial shaft movement and face wear. However, little data exist to help designers. Therefore, a test rig was developed to measure breakaway friction. The research quantitatively shows the effects of lubrication with silicone grease and a change of surface finish. By using the Taguchi statistical experimental design method, the significance of test parameters was evaluated with a minimum number of tests. It was found that fluid pressure, dwell time, and O-ring percentage squeeze affect O-ring breakaway friction more than the O-ring cross sectional diameter and axial sliding speed within the range of values tested. The authors showed that breakaway friction increased linearly with pressure. However, O-rings made of different materials had significantly different increase rates, even if they had nominally the same durometer hardness. Breakaway friction also increased with logarithm of dwell time. Again, the increase rate depended strongly on the specific O-ring material tested. These observations led the authors to believe that the typical approach of generalizing data based on generic polymer type and durometer was inappropriate.

  2. Breakaway technique training as a means of increasing confidence in managing aggression in neuroscience nursing.

    Science.gov (United States)

    Lamont, Scott; Brunero, Scott; Bailey, Alanah; Woods, Karen

    2012-08-01

    The objective of this paper was to evaluate breakaway technique training with neuroscience nursing staff as a measure of increased confidence and safety in managing aggression. A quasi experimental design was used in a sample of neuroscience nursing staff (n=31), participating in 2×1h breakaway technique workshops. The workshops consisted of supervised skills training in safe breakaway techniques. A pre- and postintervention-matched questionnaire measuring confidence and safety around managing aggressive patients, and exposure to and confidence in dealing with breakaways, was self administered. Statistically significant increases in confidence and safety in working with aggressive patients, and confidence levels for safe breakaways were reported. Qualitative comments demonstrated a desire for ongoing skills workshops. This study provides early evidence of the importance of incorporating breakaway training into existing training programs which aim to minimise and manage aggression and violence in generalist settings.

  3. Crustal-Scale Fault Interaction at Rifted Margins and the Formation of Domain-Bounding Breakaway Complexes: Insights From Offshore Norway

    Science.gov (United States)

    Osmundsen, P. T.; Péron-Pinvidic, G.

    2018-03-01

    The large-magnitude faults that control crustal thinning and excision at rifted margins combine into laterally persistent structural boundaries that separate margin domains of contrasting morphology and structure. We term them breakaway complexes. At the Mid-Norwegian margin, we identify five principal breakaway complexes that separate the proximal, necking, distal, and outer margin domains. Downdip and lateral interactions between the faults that constitute breakaway complexes became fundamental to the evolution of the 3-D margin architecture. Different types of fault interaction are observed along and between these faults, but simple models for fault growth will not fully describe their evolution. These structures operate on the crustal scale, cut large thicknesses of heterogeneously layered lithosphere, and facilitate fundamental margin processes such as deformation coupling and exhumation. Variations in large-magnitude fault geometry, erosional footwall incision, and subsequent differential subsidence along the main breakaway complexes likely record the variable efficiency of these processes.

  4. Investigation of effect of air flow rate on Zircaloy-4 oxidation kinetics and breakaway phenomenon in air at 850 .deg. C

    International Nuclear Information System (INIS)

    Maeng, Yunhwan; Lee, Jaeyoung; Park, Sanggil

    2016-01-01

    This paper analyzed an effect of flow rate on oxidation kinetics of Zircaloy-4 in air at 850 .deg. C. In case of the oxidation of Zircaloy-4 in air at 850 .deg. C, acceleration of oxidation kinetics from parabolic to linear (breakaway phenomenon) occurs. Oxidation and breakaway kinetics of the Zircaloy-4 in air was experimentally studied by changing a flow rate of argon/air mixture. Tests were conducted at 850 .deg. C under constant ratio of argon and air. The effects of flow rate on the oxidation and breakaway kinetics was observed. This paper is based on a revised and considerably extended presentation given at the 21 st International Quench Workshop. The effects of flow conditions on the oxidation kinetics of Zircaloy-4 samples were explained with residence time and percent flow efficiency. In addition, several issues were observed from this study, interdiffusion at breakaway and deformation of oxide structure by breakaway phenomenon

  5. Theoretical analysis and experimental study on breakaway torque of large-diameter magnetic liquid seal at low temperature

    Science.gov (United States)

    Zhang, Haina; Li, Decai; Wang, Qinglei; Zhang, Zhili

    2013-07-01

    The existing researches of the magnetic liquid rotation seal have been mainly oriented to the seal at normal temperature and the seal with the smaller shaft diameter less than 100 mm. However, the large-diameter magnetic liquid rotation seal at low temperature has not been reported both in theory and in application up to now. A key factor restricting the application of the large-diameter magnetic liquid rotation seal at low temperature is the high breakaway torque. In this paper, the factors that influence the breakaway torque including the number of seal stages, the injected quantity of magnetic liquid and the standing time at normal temperature are studied. Two kinds of magnetic liquid with variable content of large particles are prepared first, and a seal feedthrough with 140 mm shaft diameter is used in the experiments. All experiments are carried out in a low temperature chamber with a temperature range from 200°C to -100°C. Different numbers of seal stages are tested under the same condition to study the relation between the breakaway torque and the number of seal stages. Variable quantity of magnetic liquid is injected in the seal gap to get the relation curve of the breakaway torque and the injecting quantity of magnetic liquid. In the experiment for studying the relation between the breakaway torque and the standing time at the normal temperature, the seal feedtrough is laid at normal temperature for different period of time before it is put in the low temperature chamber. The experimental results show that the breakaway torque is proportional to the number of seal stages, the injected quantity of magnetic liquid and the standing time at the normal temperature. Meanwhile, the experimental results are analyzed and the torque formula of magnetic liquid rotation seal at low temperature is deduced from the Navier-Stokes equation on the base of the model of magnetic liquid rotation seal. The presented research can make wider application of the magnetic liquid

  6. Solute transport and the prediction of breakaway oxidation in gamma + beta Ni-Cr-Al alloys

    Science.gov (United States)

    Nesbitt, J. A.; Heckel, R. W.

    1984-01-01

    The Al transport and the condition leading to breakaway oxidation during the cyclic oxidation of gamma + beta NiCrAl alloys have been studied. The Al concentration/distance profiles were measured after various cyclic oxidation exposures at 1200 C. It was observed that cyclic oxidation results in a decreasing Al concentration at the oxide/metal interface, maintaining a constant flux of Al to the Al2O3 scale. It was also observed that breakaway oxidation occurs when the Al concentration at the oxide/metal interface approaches zero. A numerical model was developed to simulate the diffusional transport of Al and to predict breakaway oxidation in gamma + beta NiCrAl alloys undergoing cyclic oxidation. In a comparison of two alloys with similar oxide spalling characteristics, the numerical model was shown to predict correctly the onset of breakaway oxidation in the higher Al-content alloy.

  7. 49 CFR 393.43 - Breakaway and emergency braking.

    Science.gov (United States)

    2010-10-01

    ... ACCESSORIES NECESSARY FOR SAFE OPERATION Brakes § 393.43 Breakaway and emergency braking. (a) Towing vehicle protection system. Every motor vehicle, if used to tow a trailer equipped with brakes, shall be equipped with... brake systems installed on towed vehicles shall be so designed, by the use of “no-bleed-back” relay...

  8. Influence of fuel-matrix interaction on the breakaway swelling of U-Mo dispersion fuel in Al

    Energy Technology Data Exchange (ETDEWEB)

    Ryu, Ho Jin [Dept. of Nuclear and Quantum Engineering, Korea Advanced Institute of Science and Technology, Daejeon (Korea, Republic of); Kim, Yeon Soo [Nuclear Engineering Division, Argonne National Laboratory, Arogonne (United States)

    2014-04-15

    In order to advance understanding of the breakaway swelling behavior of U-Mo/Al dispersion fuel under a high-power irradiation condition, the effects of fuel-matrix interaction on the fuel performance of U-Mo/Al dispersion fuel were investigated. Fission gas release into large interfacial pores between interaction layers and the Al matrix was analyzed using both mechanistic models and observations of the post-irradiation examination results of U-Mo dispersion fuels. Using the model predictions, advantageous fuel design parameters are recommended to prevent breakaway swelling.

  9. 78 FR 54369 - Requested Administrative Waiver of the Coastwise Trade Laws: Vessel BREAKAWAY; Invitation for...

    Science.gov (United States)

    2013-09-03

    ... entered into this docket is available on the World Wide Web at http://www.regulations.gov . FOR FURTHER... BREAKAWAY is: INTENDED COMMERCIAL USE OF VESSEL: ``Sport fishing--Any fish caught remain with customers, no...

  10. The role of carbon in the breakaway oxidation of mild steel in high pressure carbon dioxide

    International Nuclear Information System (INIS)

    Surman, P.L.; Brown, A.M.

    1974-01-01

    The rate controlling step in the oxidation of iron and mild steel in CO 2 is the diffusion of iron across the inner of two layers of magnetite scale. Cation diffusion is directed towards available oxidant and hence tends to produce fresh oxide in freely available space. The initial oxidation process is thus protective and stress-free. As oxidation proceeds the gaseous reaction product, carbon monoxide, tends to accumulate at the oxide/metal interface. Eventually this leads to simultaneous carbon deposition and oxide formation. This carbon contamination allows oxidant access to oxide crystallite 'jacking points', and hence volume expansion and stressed breakaway corrosion can occur. Experiments designed to simulate the promotion, propagation and healing of breakaway oxidation and to define the conditions for carbon deposition are reported. (author)

  11. Structure of magnetic field disturbances under development of disruptive instability in the ''Tokamak-6''

    International Nuclear Information System (INIS)

    Merezhkin, V.G.

    1978-01-01

    The structure and dynamics of disturbances of a poloidal field during the development of the breakaway instability in the Tokamak-6 are investigated. The behaviour of the symmetric and dipole field component, and the peculiarities of the structure of screw disturbances in a minor and major breakaways are analyzed. It was established that the structure of screw disturbances in minor breakaways is unchangeable and that the rearrangement in major breakaways is of a discrete nature. The relationship between the symmetric and screw components of disturbances of the poloidal field at the forward front of the disturbance increase was revealed. Data on the increments, scales and structure of screw disturbances, the ratios between the symmetric and screw components of field disturbances, and also on the magnitude of energy losses in typical breakaways are given

  12. Effect of plasma current breakaway on the operating stability of the superconducting coil of the toroidal magnetic field in the T-10M installation

    International Nuclear Information System (INIS)

    Kostenko, A.I.; Kravchenko, M.Yu.; Monoszon, N.A.; Trokhachev, G.V.

    1979-01-01

    The method and calculation results of stability of a superconducting coil of the toroidal magnetic field in the T-10M installation to plasma current breakaway are presented. The calculations were performed for two values of the magnetic field induction in the centre of the plasma cross section: 3.5 and 5 T. The calculation of energy losses and heating of the superconducting coil was performed assuming the plasma current in case of breakaway decreases to zero with an infinite rate, so that the estimations obtained are maxiaum. It is shown that in case of 3.5 T induction the superconducting coil exhibits resistance to plasma current breakaways, and in case of 5 T it is necessary to use electromagnetic screening to provide stability

  13. INFLUENCE OF FUEL-MATRIX INTERACTION ON THE BREAKAWAY SWELLING OF U-MO DISPERSION FUEL IN AL

    OpenAIRE

    HO JIN RYU; YEON SOO KIM

    2014-01-01

    In order to advance understanding of the breakaway swelling behavior of U-Mo/Al dispersion fuel under a high-power irradiation condition, the effects of fuel-matrix interaction on the fuel performance of U-Mo/Al dispersion fuel were investigated. Fission gas release into large interfacial pores between interaction layers and the Al matrix was analyzed using both mechanistic models and observations of the post-irradiation examination results of U-Mo dispersion fuels. Using the model prediction...

  14. Study of structural reliability of existing concrete structures

    Science.gov (United States)

    Druķis, P.; Gaile, L.; Valtere, K.; Pakrastiņš, L.; Goremikins, V.

    2017-10-01

    Structural reliability of buildings has become an important issue after the collapse of a shopping center in Riga 21.11.2013, caused the death of 54 people. The reliability of a building is the practice of designing, constructing, operating, maintaining and removing buildings in ways that ensure maintained health, ward suffered injuries or death due to use of the building. Evaluation and improvement of existing buildings is becoming more and more important. For a large part of existing buildings, the design life has been reached or will be reached in the near future. The structures of these buildings need to be reassessed in order to find out whether the safety requirements are met. The safety requirements provided by the Eurocodes are a starting point for the assessment of safety. However, it would be uneconomical to require all existing buildings and structures to comply fully with these new codes and corresponding safety levels, therefore the assessment of existing buildings differs with each design situation. This case study describes the simple and practical procedure of determination of minimal reliability index β of existing concrete structures designed by different codes than Eurocodes and allows to reassess the actual reliability level of different structural elements of existing buildings under design load.

  15. 47 CFR 17.17 - Existing structures.

    Science.gov (United States)

    2010-10-01

    ... 47 Telecommunication 1 2010-10-01 2010-10-01 false Existing structures. 17.17 Section 17.17... STRUCTURES Federal Aviation Administration Notification Criteria § 17.17 Existing structures. (a) The requirements found in § 17.23 relating to painting and lighting of antenna structures shall not apply to those...

  16. Solar Panel Installations on Existing Structures

    OpenAIRE

    Tim D. Sass; Pe; Leed

    2013-01-01

    The rising price of fossil fuels, government incentives and growing public aware-ness for the need to implement sustainable energy supplies has resulted in a large in-crease in solar panel installations across the country. For many sites the most eco-nomical solar panel installation uses existing, southerly facing rooftops. Adding solar panels to an existing roof typically means increased loads that must be borne by the building-s structural elements. The structural desig...

  17. Concrete structures. Contribution to the safety assessment of existing structures

    Directory of Open Access Journals (Sweden)

    D. COUTO

    Full Text Available The safety evaluation of an existing concrete structure differs from the design of new structures. The partial safety factors for actions and resistances adopted in the design phase consider uncertainties and inaccuracies related to the building processes of structures, variability of materials strength and numerical approximations of the calculation and design processes. However, when analyzing a finished structure, a large number of unknown factors during the design stage are already defined and can be measured, which justifies a change in the increasing factors of the actions or reduction factors of resistances. Therefore, it is understood that safety assessment in existing structures is more complex than introducing security when designing a new structure, because it requires inspection, testing, analysis and careful diagnose. Strong knowledge and security concepts in structural engineering are needed, as well as knowledge about the materials of construction employed, in order to identify, control and properly consider the variability of actions and resistances in the structure. With the intention of discussing this topic considered complex and diffuse, this paper presents an introduction to the safety of concrete structures, a synthesis of the recommended procedures by Brazilian standards and another codes, associated with the topic, as well a realistic example of the safety assessment of an existing structure.

  18. 30 CFR 784.12 - Operation plan: Existing structures.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Operation plan: Existing structures. 784.12... PLAN § 784.12 Operation plan: Existing structures. (a) Each application shall contain a description of... and reclamation operation. The description shall include: (1) Location; (2) Plans of the structure...

  19. 30 CFR 780.12 - Operation plan: Existing structures.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Operation plan: Existing structures. 780.12... PLAN § 780.12 Operation plan: Existing structures. (a) Each application shall contain a description of... and reclamation operation. The description shall include— (1) Location; (2) Plans of the structure...

  20. The design value method and adjusted partial factor approach for existing structures

    NARCIS (Netherlands)

    Caspeele, R.; Sykora, M.; Allaix, D.L.; Steenbergen, R.D.J.M.

    2013-01-01

    In contrast to the design of new structures, the assessment of existing structures often relies on the subjective judgement of the investigating engineer. An objective verification format for existing structures based on alternative partial factors is however feasible, enabling a rather simple and

  1. Determining the in situ concrete strength of existing structures for assessing their structural safety

    NARCIS (Netherlands)

    Steenbergen, R.D.J.M.; Vervuurt, A.H.J.M.

    2012-01-01

    EN 13791 applies when assessing the in situ compressive strength of structures and precast concrete components. According to the code itself, it may be adopted when doubt arises about the compressive strength of a concrete. For assessing the structural safety of existing structures, however, the

  2. Wind/seismic comparison for upgrading existing structures

    International Nuclear Information System (INIS)

    Giller, R.A.

    1989-01-01

    This paper depicts the analysis procedures and methods used to evaluate three existing building structures for extreme wind loads. The three structures involved in this evaluation are located at the US Department of Energy's Hanford Site near Richland, Washington. This site is characterized by open flat grassland with few surrounding obstructions and has extreme winds in lieu of tornados as a design basis accident condition. This group of buildings represents a variety of construction types, including a concrete stack, a concrete load-bearing wall structure, and a rigid steel-frame building. The three structures included in this group have recently been evaluated for response to the design basis earthquake that included non-linear time history effects. The resulting loads and stresses from the wind analyses were compared to the loads and stresses resulting from seismic analyses. This approach eliminated the need to prepare additional capacity calculations that were already contained in the seismic evaluations

  3. A corrosion monitoring system for existing reinforced concrete structures.

    Science.gov (United States)

    2015-05-01

    This study evaluated a multi-parameter corrosion monitoring system for existing reinforced concrete structures in chloride-laden service environments. The system was fabricated based on a prototype concrete corrosion measurement system that : had bee...

  4. Application of Microgravity to the Assessment of Existing Structures and Structural Foundations.

    Science.gov (United States)

    1988-04-29

    UADGU Geophysique Francafse IUSRSU 6c. ADDRESS (City, State. and ZIP Code) 7b. ADDRESS (City, State, and ZIP Code) 20, Rue des Pavilions Box 65 92800...r (2.8 - 2.4) 286 AM~TCT f eldo f6 YOUOUVT 4. EXISTING STRUCTURES AND (U) CONPAGNIE DE PROSPECTION GEOPHYSIQUE FRANCAISE RUEIL-MALNAISO J LAKSHNRNRN

  5. How practice breakdowns disclose existing structures and contribute to practice innovation

    NARCIS (Netherlands)

    Loohuis, Raymond Petrus Antonius

    2015-01-01

    Practice breakdowns provide fertile ground for practice innovation because they demand a shift from structure to process. Practice breakdowns are fruitful subjects for research and practice because they disclose existing structures by prompting situated actors to become reflective on the otherwise

  6. Functional Coverage of the Human Genome by Existing Structures, Structural Genomics Targets, and Homology Models.

    Directory of Open Access Journals (Sweden)

    2005-08-01

    Full Text Available The bias in protein structure and function space resulting from experimental limitations and targeting of particular functional classes of proteins by structural biologists has long been recognized, but never continuously quantified. Using the Enzyme Commission and the Gene Ontology classifications as a reference frame, and integrating structure data from the Protein Data Bank (PDB, target sequences from the structural genomics projects, structure homology derived from the SUPERFAMILY database, and genome annotations from Ensembl and NCBI, we provide a quantified view, both at the domain and whole-protein levels, of the current and projected coverage of protein structure and function space relative to the human genome. Protein structures currently provide at least one domain that covers 37% of the functional classes identified in the genome; whole structure coverage exists for 25% of the genome. If all the structural genomics targets were solved (twice the current number of structures in the PDB, it is estimated that structures of one domain would cover 69% of the functional classes identified and complete structure coverage would be 44%. Homology models from existing experimental structures extend the 37% coverage to 56% of the genome as single domains and 25% to 31% for complete structures. Coverage from homology models is not evenly distributed by protein family, reflecting differing degrees of sequence and structure divergence within families. While these data provide coverage, conversely, they also systematically highlight functional classes of proteins for which structures should be determined. Current key functional families without structure representation are highlighted here; updated information on the "most wanted list" that should be solved is available on a weekly basis from http://function.rcsb.org:8080/pdb/function_distribution/index.html.

  7. Influence of Fuel-Matrix Interaction on the Deformation of U-Mo Dispersion Fuel

    Energy Technology Data Exchange (ETDEWEB)

    Ryu, Ho Jin [Korea Advanced Institute of Science and Technology, Daejeon (Korea, Republic of); Kim, Yeon Soo [Argonne National Laboratory, Chicago (United States)

    2014-05-15

    In order to predict the fuel plate failure leading to breakaway swelling in the meat, an understanding of the effects of the fuel-matrix interaction behavior on the deformation of fuel meat is necessary. However, the effects of IL formation on the development of breakaway swelling have not been studied thoroughly. A mechanism that explains large pore growth that leads to breakaway swelling has not been included in the existing fuel performance models. In this study, the effect of the fuel-matrix interaction on large interfacial porosity development at the IL-Al interface is analyzed using both mechanistic correlations and observations from the post-irradiation examination results of U-Mo Dispersion fuels. The effects of fuel-matrix interaction on the fuel performance of U-Mo/Al Dispersion fuel were investigated. Fuel-matrix interaction bears the causes for breakaway swelling that can lead to a fuel failure under a high-power irradiation condition. Fission gas atoms are released from U-Mo particles to the interaction layer via diffusion and recoil. The fission gases released from the U-Mo and produced in the ILs are further released to the IL-Al interface by diffusion in the IL and recoil. Large pore formation at the IL-Al interface is attributed to the active diffusion of fission gas atoms in the ILs and coalescence between the small bubbles there. A model calculation showed that IL growth increases the probability of forming a breakaway swelling condition. ILs are connected to each other and the Al matrix decreases as ILs grow. When more ILs are interconnected, breakaway swelling can occur when the effective stress from the fission gas pressure in the IL-Al interfacial pore becomes larger than the yield strength of the Al matrix.

  8. Life-Cycle Assessment of Seismic Retrofit Strategies Applied to Existing Building Structures

    Directory of Open Access Journals (Sweden)

    Umberto Vitiello

    2016-12-01

    Full Text Available In the last few years, the renovation and refurbishment of existing buildings have become the main activities of the construction industry. In particular, many studies have recently focused on the mechanical and energy performances of existing retrofitted/refurbished facilities, while some research has addressed the environmental effects of such operations. The present study aims to assess the environmental impact of some retrofit interventions on an existing reinforced concrete (RC building. Once the structural requirements have been satisfied and the environmental effects of these retrofit solutions defined, the final purpose of this study is to identify the most environmentally sustainable retrofit strategy. The environmental impact of the structural retrofit options is assessed using a life-cycle assessment (LCA. This paper sets out a systematic approach that can be adopted when choosing the best structural retrofit option in terms of sustainability performance. The final aim of the study is to also provide a tool for researchers and practitioners that reflects a deep understanding of the sustainability aspects of retrofit operations and can be used for future researches or practical activities.

  9. Assessment and Rehabilitation Issues Concerning Existing 70’s Structural Stock

    Science.gov (United States)

    Sabareanu, E.

    2017-06-01

    The last 30 years were very demanding in terms of norms and standards change concerning the structural calculus for buildings, leaving a large stock of structures erected during 70-90 decades in a weak position concerning seismic loads and loads level for live loads, wind and snow. In the same time, taking into account that a large amount of buildings are in service all over the country, they cannot be demolished, but suitable rehabilitation methods should be proposed, structural durability being achieved. The paper proposes some rehabilitation methods suitable in terms of structural safety and cost optimization for diaphragm reinforced concrete structures, with an example on an existing multi storey building.

  10. Passive Vibration Control of Existing Structures by Gravity-Loaded Cables

    Science.gov (United States)

    Alvis, E.; Tsang, H. H.; Hashemi, M. J.

    2017-06-01

    Structures with high concentration of mass at or close to the top such as highway bridge piers are vulnerable in earthquakes or accidents. In this paper, a simple and convenient retrofit strategy is proposed for minimizing vibrations and damages, extending service life and preventing collapse of existing structures. The proposed system comprises of tension-only cables secured to the sides of the structure through gravity anchor blocks that are free to move in vertical shafts. The system is installed in such a way that the cables do not induce unnecessary stress on the main structure when there is no lateral motion or vibration. The effectiveness of controlling global structural responses is investigated for tension-only bilinear-elastic behaviour of cables. Results of a realistic case study for a reinforced concrete bridge pier show that response reduction is remarkably well under seismic excitation.

  11. Retrofit of heat exchanger networks considering pressure drop and existing structure: a new targeting procedure

    International Nuclear Information System (INIS)

    PanjehShahi, M.H.; Nouzari, M.M.

    2002-01-01

    A new retrofit targeting procedure, based on pinch technology has been developed. The procedure considers existing structure and hydrodynamic system of a given network as two main constraint during targeting. The procedure uses a linear programming model to consider existing structure. The model finds a network structure that has maximum compatibility with existing structure. Furthermore, the procedure using the pressure drop equations, can consider decreasing the film coefficients of streams due to increasing network area. Good compatibility between old and new networks and non replacement of hydrodynamic equipment cause to the best use of capital in retrofit projects. The procedure has been checked by doing two case studies, in which the results compared to the established methods, and realized significant improvement

  12. Structural behaviour characterization of existing adobe constructions in Aveiro

    OpenAIRE

    Varum, H.; Costa, A.; Martins, T.; Pereira, H.; Almeida, J.; Rodrigues, H.; Silveira, D.

    2007-01-01

    Adobe was a widely used construction material in Aveiro, Portugal, till the middle of the 20th century. Nowadays, adobe can still be found in varied types of constructions, many of which are of cultural, historical, and also architectural recognized value. The existing adobe buildings present an important level of structural damage and, in many cases, are even near to ruin, having the majority a high vulnerability to seismic actions. To face the lack of information concerning the mechanica...

  13. Comparative Application of Capacity Models for Seismic Vulnerability Evaluation of Existing RC Structures

    International Nuclear Information System (INIS)

    Faella, C.; Lima, C.; Martinelli, E.; Nigro, E.

    2008-01-01

    Seismic vulnerability assessment of existing buildings is one of the most common tasks in which Structural Engineers are currently engaged. Since, its is often a preliminary step to approach the issue of how to retrofit non-seismic designed and detailed structures, it plays a key role in the successful choice of the most suitable strengthening technique. In this framework, the basic information for both seismic assessment and retrofitting is related to the formulation of capacity models for structural members. Plenty of proposals, often contradictory under the quantitative standpoint, are currently available within the technical and scientific literature for defining the structural capacity in terms of force and displacements, possibly with reference to different parameters representing the seismic response. The present paper shortly reviews some of the models for capacity of RC members and compare them with reference to two case studies assumed as representative of a wide class of existing buildings

  14. The existence of very large-scale structures in the universe

    Energy Technology Data Exchange (ETDEWEB)

    Goicoechea, L J; Martin-Mirones, J M [Universidad de Cantabria Santander, (ES)

    1989-09-01

    Assuming that the dipole moment observed in the cosmic background radiation (microwaves and X-rays) can be interpreted as a consequence of the motion of the observer toward a non-local and very large-scale structure in our universe, we study the perturbation of the m-z relation by this inhomogeneity, the dynamical contribution of sources to the dipole anisotropy in the X-ray background and the imprint that several structures with such characteristics would have had on the microwave background at the decoupling. We conclude that in this model the observed anisotropy in the microwave background on intermediate angular scales ({approx}10{sup 0}) may be in conflict with the existence of superstructures.

  15. Structural Safety Assessment of Existing Multiarch Tunnel: A Case Study

    Directory of Open Access Journals (Sweden)

    Jinxing Lai

    2017-01-01

    Full Text Available Structural health assessment is one of the key activities in maintaining the performance of a tunnel during its service life. Due to the development of modern detection technology, comprehensive structural health assessment system is being established for operating tunnels. To evaluate the actual operational state of Shitigou tunnel, overall detection of the liner crack, tunnel seepage, and liner void was conducted by employing the modern detection technology, such as crack width monitoring technology, concrete strength monitoring technology, and electromagnetic wave nondestructive monitoring technology. Through the statistical analysis of the detection results, the distribution characteristic, development law, and damage grade of structural defects were obtained. Tunnel liner cracks are mainly located on the middle wall; serious water leakage is encountered on the side wall, middle wall, and vault; the strength of foundation and liner structure of left tunnel does not meet the design requirement; the liner voids are mostly located at the tunnel entrance section, especially, on the tunnel vault; and the proportion of influence factors of structural defects should be considered. The research results presented for this study can serve as references for effective design and health assessment of existing multiarch tunnel projects.

  16. Organizing Defense Logistics: What Strategic Structures Should Exist for the Defense Supply Chain

    National Research Council Canada - National Science Library

    Maddox, Edward D

    2005-01-01

    .... The primary research question of this study was: What strategic organizational structures should exist within the Department of Defense to facilitate further integration of the defense supply chain...

  17. Zircaloy-4 and M5 high temperature oxidation and nitriding in air

    Energy Technology Data Exchange (ETDEWEB)

    Duriez, C. [Institut de Radioprotection et Surete Nucleaire, Direction de Prevention des Accidents Majeurs, Centre de Cadarache, 13115 St Paul Lez Durance (France)], E-mail: christian.duriez@irsn.fr; Dupont, T.; Schmet, B.; Enoch, F. [Universite Technologique de Troyes, BP 2060, 10010 Troyes (France)

    2008-10-15

    For the purpose of nuclear power plant severe accident analysis, degradation of Zircaloy-4 and M5 cladding tubes in air at high temperature was investigated by thermo-gravimetric analysis, in isothermal conditions, in a 600-1200 deg. C temperature range. Alloys were investigated either in a 'as received' bare state, or after steam pre-oxidation at 500 {sup o}C to simulate in-reactor corrosion. At the beginning of air exposure, the oxidation rate obeys a parabolic law, characteristic of solid-state diffusion limited regime. Parabolic rate constants compare, for Zircaloy-4 as well as for M5, with recently assessed correlations for high temperature Zircaloy-4 steam-oxidation. A thick layer of dense protective zirconia having a columnar structure forms during this diffusion-limited regime. Then, a kinetic transition (breakaway type) occurs, due to radial cracking along the columnar grain boundaries of this protective dense oxide scale. The breakaway is observed for a scale thickness that strongly increases with temperature. At the lowest temperatures, the M5 alloy appears to be breakaway-resistant, showing a delayed transition compared to Zircaloy-4. However, for both alloys, a pre-existing corrosion scale favours the transition, which occurs much earlier. The post transition kinetic regime is linear only for the lowest temperatures investigated. From 800 deg. C, a continuously accelerated regime is observed and is associated with formation of a strongly porous non-protective oxide. A mechanism of nitrogen-assisted oxide growth, involving formation and re-oxidation of ZrN particles, as well as nitrogen associated zirconia phase transformations, is proposed to be responsible for this accelerated degradation.

  18. Reliability Analysis and Test Planning using CAPO-Test for Existing Structures

    DEFF Research Database (Denmark)

    Sørensen, John Dalsgaard; Engelund, S.; Faber, Michael Havbro

    2000-01-01

    Evaluation of the reliability of existing concrete structures often requires that the compressive strength of the concrete is estimated on the basis of tests performed with concrete samples from the structure considered. In this paper the CAPO-test method is considered. The different sources...... of uncertainty related to this method are described. It is shown how the uncertainty in the transformation from the CAPO-test results to estimates of the concrete strength can be modeled. Further, the statistical uncertainty is modeled using Bayesian statistics. Finally, it is shown how reliability-based optimal...... planning of CAPO-tests can be performed taking into account the expected costs due to the CAPO-tests and possible repair or failure of the structure considered. An illustrative example is presented where the CAPO-test is compared with conventional concrete cylinder compression tests performed on cores...

  19. "You can't buy something you aren't"

    DEFF Research Database (Denmark)

    Christiansen, Ask Vest; Hjørngaard, Martin Wang

    2013-01-01

    Wind resistance is the primary external factor teams organise themselves around in cycling. In order to share this burden, members of opposing teams often cooperate, e.g. to secure the existence of a breakaway. To avoid free-riders the riders in question form a tacit social contract on sharing th...

  20. Wave fields in Weyl spaces and conditions for the existence of a preferred pseudo-Riemannian structure

    International Nuclear Information System (INIS)

    Audretsch, J.; Gaehler, F.; Straumann, N.

    1984-01-01

    Previous axiomatic approaches to general relativity which led to a Weylian structure of space-time are supplemented by a physical condition which implies the existence of a preferred pseudo-Riemannian structure. It is stipulated that the trajectories of the short wave limit of classical massive fields agree with the geodesics of the Weyl connection and it is shown that this is equivalent to the vanishing of the covariant derivative of a ''mass function'' of nontrivial Weyl type.This in turn is proven to be equivalent to the existence of a preferred metric of the conformal structure such that the Weyl connection is reducible to a connection of the bundle of orthonormal frames belonging to this distinguished metric. (orig.)

  1. A simplified procedure for mass and stiffness estimation of existing structures

    Science.gov (United States)

    Nigro, Antonella; Ditommaso, Rocco; Carlo Ponzo, Felice; Salvatore Nigro, Domenico

    2016-04-01

    This work focuses the attention on a parametric method for mass and stiffness identification of framed structures, based on frequencies evaluation. The assessment of real structures is greatly affected by the consistency of information retrieved on materials and on the influence of both non-structural components and soil. One of the most important matter is the correct definition of the distribution, both in plan and in elevation, of mass and stiffness: depending on concentrated and distributed loads, the presence of infill panels and the distribution of structural elements. In this study modal identification is performed under several mass-modified conditions and structural parameters consistent with the identified modal parameters are determined. Modal parameter identification of a structure before and after the introduction of additional masses is conducted. By considering the relationship between the additional masses and modal properties before and after the mass modification, structural parameters of a damped system, i.e. mass, stiffness and damping coefficient are inversely estimated from these modal parameters variations. The accuracy of the method can be improved by using various mass-modified conditions. The proposed simplified procedure has been tested on both numerical and experimental models by means linear numerical analyses and shaking table tests performed on scaled structures at the Seismic Laboratory of the University of Basilicata (SISLAB). Results confirm the effectiveness of the proposed procedure to estimate masses and stiffness of existing real structures with a maximum error equal to 10%, under the worst conditions. Acknowledgements This study was partially funded by the Italian Civil Protection Department within the project DPC-RELUIS 2015 - RS4 ''Seismic observatory of structures and health monitoring''.

  2. Microtunneling techniques to form an insitu barrier around existing structures

    International Nuclear Information System (INIS)

    Coller, P.J.; Abbott, D.G.

    1994-01-01

    The use of microtunneling techniques to construct underground structures has been available for many years. The technique, typically termed pipe roofing, is well proven and, to date, has been used principally to form underground access under existing structures where the use of cut and cover or conventional tunneling techniques was either impossible or too expensive. The first project involving the use of Iseki equipment, the first use of the pipe roofing technique as far as we are aware, was in 1971. This was followed by a number of projects in Japan, together with projects in Singapore and Hong Kong, totaling 12 projects. More recently, projects have been completed in Singapore and Japan and are currently in progress in Japan and Malaysia. This paper will briefly describe the use of the technique and the use of the new Iseki Unclemole for hard rock excavation to construct the largest pipe roof project ever undertaken in the world, together with other projects. The pipe roofing technique allows the construction of underground structures, in a variety of shapes and forms, by the use of remotely operated microtunnel machines. The paper will describe the potential application of this technique in the areas of hazardous and nuclear waste management

  3. Assessing seismic adequacy of existing nuclear power plant structures

    International Nuclear Information System (INIS)

    Belyaev, V.; Vinogradov, V.; Privalov, S.; Shishenin, V.

    2003-01-01

    Nowadays Russia's specialists perform a huge amount of works to revaluate the NPP safety. These works are certain to include refinement of NPP safety assessment under the effects of specific dynamic loads, earthquake effects included. It should be noted, that a number of Russian NPPs now in operation had been designed either with no account of these loads, or under the requirements which are underestimated as compared with the modern requirements on the external load composition and rate. Revaluation of NPP seismic safety is based on the results of the works taken under orderly sequence on assessment of (1) seismic input and ground effects; (2) structure response and state; (3) equipment and pipelines response and state. The paper considers the methods of NPP structures response and state assessment. Therewith we assume that ground motion predicted behavior at the construction basement has been preset for the SSE and OBE conditions and the effects of soil-structure interaction, including the situation of possible soft soil liquefaction. Necessity to determine both the reaction of a construction and its state as a whole as well as its elements reaction, to evaluate their bearing capacity and destruction zones formation makes it necessary to make up a detailed structural model, which is usually a finite element one. Since seismic revaluation is to be performed for the existing structures, characteristics of which can substantially differ from the design ones, revealing the actual state of this structures becomes critical. If the real values of physical and mechanical properties of the structure materials, connections of elements etc. are used as initial data in a structural model this permits to increase the design assessment credibility and reliability substantially. The paper analyzes the results of determining these initial assessments while inspecting several Russian NPPs on the basis of a 'combined' method. This method is realized at two consecutive stages. The

  4. 76 FR 43230 - National Pollutant Discharge Elimination System-Cooling Water Intake Structures at Existing...

    Science.gov (United States)

    2011-07-20

    ... ENVIRONMENTAL PROTECTION AGENCY 40 CFR Parts 122 and 125 [EPA-HQ-OW-2008-0667, FRL-9441-8] RIN 2040-AE95 National Pollutant Discharge Elimination System--Cooling Water Intake Structures at Existing Facilities and Phase I Facilities AGENCY: Environmental Protection Agency (EPA). ACTION: Proposed rule...

  5. Incorporating A Structured Writing Process into Existing CLS Curricula.

    Science.gov (United States)

    Honeycutt, Karen; Latshaw, Sandra

    2014-01-01

    Good communication and critical thinking are essential skills for all successful professionals, including Clinical Laboratory Science/Medical Laboratory Science (CLS/MLS) practitioners. Professional programs can incorporate writing assignments into their curricula to improve student written communication and critical thinking skills. Clearly defined, scenario-focused writing assignments provide student practice in clearly articulating responses to proposed problems or situations, researching and utilizing informational resources, and applying and synthesizing relevant information. Assessment rubrics, structured feedback, and revision writing methodologies help guide students through the writing process. This article describes how a CLS Program in a public academic medical center, located in the central United States (US) serving five centrally-located US states has incorporated writing intensive assignments into an existing 11-month academic year using formal, informal and reflective writing to improve student written communication and critical thinking skills. Faculty members and employers of graduates assert that incorporating writing intensive requirements have better prepared students for their professional role to effectively communicate and think critically.

  6. On the use of NDT Data for Reliability-Based Assessment of Existing Timber Structures

    DEFF Research Database (Denmark)

    Sousa, Hélder S.; Sørensen, John Dalsgaard; Kirkegaard, Poul Henning

    2013-01-01

    The objective of this paper is to address the possibilities of using non-destructive testing (NDT) data for updating information and obtaining adequate characterization of the reliability level of existing timber structures and, also, for assessing the evolution in time of performance...... of these structures when exposed to deterioration. By improving the knowledge upon the mechanical properties of timber, better and more substantiated decisions after a reliability safety assessment are aimed at. Bayesian methods are used to update the mechanical properties of timber and reliability assessment......, and information of NDT is also used to calibrate these models. The proposed approach is used for reliability assessment of different structural timber systems. Reliability of the structural system is assessed regarding the failure consequences of individual elements defined as key elements which were determined...

  7. On the existence of europium aluminum oxynitrides with a magnetoplumbite or beta-alumina type structure

    NARCIS (Netherlands)

    Hintzen, H.T.J.M.; Hanssen, R.; Jansen, S.R.; Metselaar, R.

    1999-01-01

    In the literature confusion exists concerning the structure type, the valence of europium, and the amount of nitrogen incorporation of the compound europium aluminum oxynitride. By using X-ray diffraction and luminescence measurements, we show that europium aluminum oxynitride has the

  8. Test of determination of nucleon structure functions in the hypothesis of scalar di-quark existence

    International Nuclear Information System (INIS)

    Tavernier, P.; Dugne, J.J.

    1992-01-01

    The authors present the nucleon structure functions that have been obtained in the hypothesis of existence of a scalar di-quark, progressively broken by increasing energy of electromagnetic probe (Stockolm model). Comparisons with other models and experimental results are presented. 20 figs

  9. Earthquake Protection of Existing Structures with Limited Seismic Joint: Base Isolation with Supplemental Damping versus Rotational Inertia

    Directory of Open Access Journals (Sweden)

    Dario De Domenico

    2018-01-01

    Full Text Available Existing civil engineering structures having strategic importance, such as hospitals, fire stations, and power plants, often do not comply with seismic standards in force today, as they were designed and built based on past structural guidelines. On the other hand, due to their special importance, structural integrity of such buildings is of vital importance during and after earthquakes, which puts demands on strategies for their seismic protection. In this regard, seismic base isolation has been widely employed; however, the existing limited seismic joint between adjacent buildings may hamper this application because of the large displacements concentrated at the isolation floor. In this paper, we compare two possible remedies: the former is to provide supplemental damping in conventional base isolation systems and the latter consists in a combination of base isolation with supplemental rotational inertia. For the second strategy, a mechanical device, called inerter, is arranged in series with spring and dashpot elements to form the so-called tuned-mass-damper-inerter (TMDI directly connected to an isolation floor. Several advantages of this second system as compared to the first one are outlined, especially with regard to the limitation of floor accelerations and interstory drifts, which may be an issue for nonstructural elements and equipment, in addition to disturbing occupants. Once the optimal design of the TMDI is established, possible implementation of this system into existing structures is discussed.

  10. Does a network structure exist in molecular liquid SnI4 and GeI4?

    Science.gov (United States)

    Sakagami, Takahiro; Fuchizaki, Kazuhiro

    2017-04-01

    The existence of a network structure consisting of electrically neutral tetrahedral molecules in liquid SnI4 and GeI4 at ambient pressure was examined. The liquid structures employed for the examination were obtained from a reverse Monte Carlo analysis. The structures were physically interpreted by introducing an appropriate intermolecular interaction. A ‘bond’ was then defined as an intermolecular connection that minimizes the energy of intermolecular interaction. However, their ‘bond’ energy is too weak for the ‘bond’ and the resulting network structure to be defined statically. The vertex-to-edge orientation between the nearest molecules is so ubiquitous that almost all of the molecules in the system can take part in the network, which is reflected in the appearance of a prepeak in the structure factor.

  11. Structural health monitoring of an existing PC box girder bridge with distributed HCFRP sensors in a destructive test

    Science.gov (United States)

    Yang, Caiqian; Wu, Zhishen; Zhang, Yufeng

    2008-06-01

    The application of hybrid carbon fiber reinforced polymer (HCFRP) sensors was addressed to monitor the structural health of an existing prestressed concrete (PC) box girder bridge in a destructive test. The novel HCFRP sensors were fabricated with three types of carbon tows in order to realize distributed and broad-based sensing, which is characterized by long-gauge length and low cost. The HCFRP sensors were bonded on the bottom and side surfaces of the existing bridge to monitor its structural health. The gauge lengths of the sensors bonded on the bottom and side surfaces were 1.5 m and 1.0 m, respectively. The HCFRP sensors were distributed on the bridge for two purposes. One was to detect damage and monitor the structural health of the bridge, such as the initiation and propagation of new cracks, strain distribution and yielding of steel reinforcements. The other purpose was to monitor the propagation of existing cracks. The good relationship between the change in electrical resistance and load indicates that the HCFRP sensors can provide actual infrastructures with a distributed damage detection and structural health monitoring system. Corrections were made to this article on 13 May 2008. The corrected electronic version is identical to the print version.

  12. Structural health monitoring of an existing PC box girder bridge with distributed HCFRP sensors in a destructive test

    International Nuclear Information System (INIS)

    Yang Caiqian; Wu Zhishen; Zhang Yufeng

    2008-01-01

    The application of hybrid carbon fiber reinforced polymer (HCFRP) sensors was addressed to monitor the structural health of an existing prestressed concrete (PC) box girder bridge in a destructive test. The novel HCFRP sensors were fabricated with three types of carbon tows in order to realize distributed and broad-based sensing, which is characterized by long-gauge length and low cost. The HCFRP sensors were bonded on the bottom and side surfaces of the existing bridge to monitor its structural health. The gauge lengths of the sensors bonded on the bottom and side surfaces were 1.5 m and 1.0 m, respectively. The HCFRP sensors were distributed on the bridge for two purposes. One was to detect damage and monitor the structural health of the bridge, such as the initiation and propagation of new cracks, strain distribution and yielding of steel reinforcements. The other purpose was to monitor the propagation of existing cracks. The good relationship between the change in electrical resistance and load indicates that the HCFRP sensors can provide actual infrastructures with a distributed damage detection and structural health monitoring system. Corrections were made to this article on 13 May 2008. The corrected electronic version is identical to the print version

  13. ENERGY DEMANDS OF THE EXISTING COLLECTIVE BUILDINGS WITH BEARING STRUCTURE OF LARGE PRECAST CONCRETE PANELS FROM TIMISOARA

    Directory of Open Access Journals (Sweden)

    Pescari S.

    2015-05-01

    Full Text Available One of the targets of EU Directives on the energy performance of buildings is to reduce the energy consumption of the existing buildings by finding efficient solutions for thermal rehabilitation. In order to find the adequate solutions, the first step is to establish the current state of the buildings and to determine their actual energy consumption. The current paper aims to present the energy demands of the existing buildings with bearing structure of large precast concrete panels in the city of Timisoara. Timisoara is one of the most important cities in the west side of Romania, being on the third place in terms of size and economic development. The Census of Population and Housing of 2011 states that Timisoara has about 127841 private dwellings and 60 percent of them are collective buildings. Energy demand values of the existing buildings with bearing structure of large precast concrete panels in Timisoara, in their current condition, are higher than the accepted values provided in the Romanian normative, C107. The difference between these two values can reach up to 300 percent.

  14. Strengthening of Existing Bridge Structures for Shear and Bending with Carbon Textile-Reinforced Mortar

    Directory of Open Access Journals (Sweden)

    Martin Herbrand

    2017-09-01

    Full Text Available Increasing traffic loads and changes in code provisions lead to deficits in shear and flexural capacity of many existing highway bridges. Therefore, a large number of structures are expected to require refurbishment and strengthening in the future. This projection is based on the current condition of many older road bridges. Different strengthening methods for bridges exist to extend their service life, all having specific advantages and disadvantages. By applying a thin layer of carbon textile-reinforced mortar (CTRM to bridge deck slabs and the webs of pre-stressed concrete bridges, the fatigue and ultimate strength of these members can be increased significantly. The CTRM layer is a combination of a corrosion resistant carbon fiber reinforced polymer (CFRP fabric and an efficient mortar. In this paper, the strengthening method and the experimental results obtained at RWTH Aachen University are presented.

  15. Strengthening of Existing Bridge Structures for Shear and Bending with Carbon Textile-Reinforced Mortar.

    Science.gov (United States)

    Herbrand, Martin; Adam, Viviane; Classen, Martin; Kueres, Dominik; Hegger, Josef

    2017-09-19

    Increasing traffic loads and changes in code provisions lead to deficits in shear and flexural capacity of many existing highway bridges. Therefore, a large number of structures are expected to require refurbishment and strengthening in the future. This projection is based on the current condition of many older road bridges. Different strengthening methods for bridges exist to extend their service life, all having specific advantages and disadvantages. By applying a thin layer of carbon textile-reinforced mortar (CTRM) to bridge deck slabs and the webs of pre-stressed concrete bridges, the fatigue and ultimate strength of these members can be increased significantly. The CTRM layer is a combination of a corrosion resistant carbon fiber reinforced polymer (CFRP) fabric and an efficient mortar. In this paper, the strengthening method and the experimental results obtained at RWTH Aachen University are presented.

  16. The oxidation of Type 310S stainless steel in mixed gases at elevated temperatures

    Energy Technology Data Exchange (ETDEWEB)

    Wolf, J.S. (Clemson Univ., SC (United States). Dept. of Mechanical Engineering); Cavin, O.B.; DeVan, J.H. (Oak Ridge National Lab., TN (United States))

    1992-04-01

    Sheet specimens of Type 310S stainless steel were exposed to air as well as to lean'' and rich'' sulfidizing atmospheres at temperatures near 900{degrees}C to determine the relationships that exist between the scale structure, the rate of reaction, and the stresses generated during exposure. One goal of this experimental research program was to examine how these factors might be related to the breakdown of protective scales in sulfidizing atmospheres. It was found that the scales formed in air and the lean'' atmosphere are protective and non-spalling while those formed in the rich'' atmosphere spall, initially react at rates 1000 times greater than counterparts in less aggressive atmospheres, and later exhibit a breakaway''-type rapid reaction. Only those scales formed in air provide the cooperative, tractive interfacial forces required to produce uniform dilatation and deformation of the substrate. However, evidence exists for at least localized stresses in all of the scales examined.

  17. The oxidation of Type 310S stainless steel in mixed gases at elevated temperatures

    Energy Technology Data Exchange (ETDEWEB)

    Wolf, J.S. [Clemson Univ., SC (United States). Dept. of Mechanical Engineering; Cavin, O.B.; DeVan, J.H. [Oak Ridge National Lab., TN (United States)

    1992-04-01

    Sheet specimens of Type 310S stainless steel were exposed to air as well as to ``lean`` and ``rich`` sulfidizing atmospheres at temperatures near 900{degrees}C to determine the relationships that exist between the scale structure, the rate of reaction, and the stresses generated during exposure. One goal of this experimental research program was to examine how these factors might be related to the breakdown of protective scales in sulfidizing atmospheres. It was found that the scales formed in air and the ``lean`` atmosphere are protective and non-spalling while those formed in the ``rich`` atmosphere spall, initially react at rates 1000 times greater than counterparts in less aggressive atmospheres, and later exhibit a ``breakaway``-type rapid reaction. Only those scales formed in air provide the cooperative, tractive interfacial forces required to produce uniform dilatation and deformation of the substrate. However, evidence exists for at least localized stresses in all of the scales examined.

  18. Nonthermal effects on existence domains for dust-acoustic solitary structures in plasmas with two-temperature ions

    International Nuclear Information System (INIS)

    Verheest, Frank; Hellberg, Manfred A.

    2010-01-01

    Large dust-acoustic waves are investigated in a multispecies plasma model consisting of adiabatic, negatively charged dust, in the presence of two ion species, a cooler one with a Boltzmann distribution and a hotter one with a nonthermal Cairns distribution. This is treated through a Sagdeev pseudopotential analysis, in a way which is physically transparent and puts great emphasis on the existence domains in compositional parameter space. The occurrence and properties of positive double layers have been studied, and this automatically also includes the existence domains for positive solitons with velocities and amplitudes smaller than the double layer values. A brief discussion is given of negative solitons and of conditions affecting the coexistence of negative and positive solitary structures for the same plasma properties. Subject to simple adjustments, these results apply equally to the conjugate plasma model of positive dust and two electron species, and in the limit without nonthermal effects, to the case of ion-acoustic solitary structures in a plasma with double Boltzmann electrons, and extensions of earlier results of that problem are presented.

  19. Existence regimes for the formation of nonlinear dissipative structures in inhomogeneous magnetoplasmas with non-Maxwellian electrons

    Science.gov (United States)

    Masood, W.; Zahoor, Sara; Gul-e-Ali, Ahmad, Ali

    2016-09-01

    Nonlinear dissipative structures are studied in one and two dimensions in nonuniform magnetized plasmas with non-Maxwellian electrons. The dissipation is incorporated in the system through ion-neutral collisions. Employing the drift approximation, nonlinear drift waves are derived in 1D, whereas coupled drift-ion acoustic waves are derived in 2D in the weak nonlinearity limit. It is found that the ratio of the diamagnetic drift velocity to the velocity of nonlinear structure determines the nature (compressive or rarefactive) of the shock structure. The upper and lower bounds for velocity of the nonlinear shock structures are also found. It is noticed that the existence regimes for the drift shock waves in one and two dimensions for Cairns distributed electrons are very distinct from those with kappa distributed electrons. Interestingly, it is found that both compressive and rarefactive shock structures could be obtained for the one dimensional drift waves with kappa distributed electrons.

  20. Existence regimes for the formation of nonlinear dissipative structures in inhomogeneous magnetoplasmas with non-Maxwellian electrons

    Energy Technology Data Exchange (ETDEWEB)

    Masood, W. [COMSATS Institute of Information Technology, Park Road, Chak Shahzad, Islamabad (Pakistan); National Centre for Physics, Shahdara Valley Road, Islamabad (Pakistan); Zahoor, Sara [COMSATS Institute of Information Technology, Park Road, Chak Shahzad, Islamabad (Pakistan); Gul-e-Ali [Theoretical Plasma Physics Group, Department of Physics, Quaid-i-Azam University, Islamabad 45320 (Pakistan); Ahmad, Ali, E-mail: aliahmad79@hotmail.com [National Centre for Physics, Shahdara Valley Road, Islamabad (Pakistan)

    2016-09-15

    Nonlinear dissipative structures are studied in one and two dimensions in nonuniform magnetized plasmas with non-Maxwellian electrons. The dissipation is incorporated in the system through ion-neutral collisions. Employing the drift approximation, nonlinear drift waves are derived in 1D, whereas coupled drift-ion acoustic waves are derived in 2D in the weak nonlinearity limit. It is found that the ratio of the diamagnetic drift velocity to the velocity of nonlinear structure determines the nature (compressive or rarefactive) of the shock structure. The upper and lower bounds for velocity of the nonlinear shock structures are also found. It is noticed that the existence regimes for the drift shock waves in one and two dimensions for Cairns distributed electrons are very distinct from those with kappa distributed electrons. Interestingly, it is found that both compressive and rarefactive shock structures could be obtained for the one dimensional drift waves with kappa distributed electrons.

  1. Sensitivity analysis on the zirconium ignition in a postulated SFP loss of coolant accident

    International Nuclear Information System (INIS)

    Park, Sanggil; Lee, Jaeyoung; Kim, Sun-ki; Chun, Tae-hyun; Bang, Je-geon

    2016-01-01

    From both SFP complete LOCA experiments, it was observed that zirconium alloy cladding temperature was abruptly increased at a certain point and the cladding was almost fully oxidized. To capture this phenomenon, the concept of air oxidation breakaway model was adopted in MELCOR code. This paper examines this air oxidation breakaway model by comparing the SFP project test data and MELCOR code calculation results by using this model. The air oxidation model parameters are slightly altered to see their sensitivities on the occurrence of the zirconium ignition. Through such sensitivity analysis, limitations of the air oxidation breakaway model are revealed in comparison to the actual zirconium ignition phenomenon during air ingress scenarios. In addition, ways to overcome the identified limitations of the air oxidation model are recommended to estimate better the zirconium ignition phenomenon in SFP sequences. In this paper, the zirconium ignition phenomenon was reviewed and the model to capture this phenomenon was investigated. The model is the air oxidation breakaway model in MELCOR code, and its sensitivity of the model parameters on the time to ignition was studied. From the sensitivity analysis, the slight change of model parameters induce the large variation of the time to ignition. The model itself includes its weakness to fully represent both the air oxidation breakaway phenomenon and the followed zirconium ignition behavior. Furthermore, this model considers no effect of N2 on the cladding degradation and its promoted exothermic heat release

  2. Sensitivity analysis on the zirconium ignition in a postulated SFP loss of coolant accident

    Energy Technology Data Exchange (ETDEWEB)

    Park, Sanggil; Lee, Jaeyoung [Handong Global Univ., Pohang (Korea, Republic of); Kim, Sun-ki; Chun, Tae-hyun; Bang, Je-geon [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2016-10-15

    From both SFP complete LOCA experiments, it was observed that zirconium alloy cladding temperature was abruptly increased at a certain point and the cladding was almost fully oxidized. To capture this phenomenon, the concept of air oxidation breakaway model was adopted in MELCOR code. This paper examines this air oxidation breakaway model by comparing the SFP project test data and MELCOR code calculation results by using this model. The air oxidation model parameters are slightly altered to see their sensitivities on the occurrence of the zirconium ignition. Through such sensitivity analysis, limitations of the air oxidation breakaway model are revealed in comparison to the actual zirconium ignition phenomenon during air ingress scenarios. In addition, ways to overcome the identified limitations of the air oxidation model are recommended to estimate better the zirconium ignition phenomenon in SFP sequences. In this paper, the zirconium ignition phenomenon was reviewed and the model to capture this phenomenon was investigated. The model is the air oxidation breakaway model in MELCOR code, and its sensitivity of the model parameters on the time to ignition was studied. From the sensitivity analysis, the slight change of model parameters induce the large variation of the time to ignition. The model itself includes its weakness to fully represent both the air oxidation breakaway phenomenon and the followed zirconium ignition behavior. Furthermore, this model considers no effect of N2 on the cladding degradation and its promoted exothermic heat release.

  3. Safety assessment of existing highway bridges and viaducts

    NARCIS (Netherlands)

    Maljaars, J.; Steenbergen, R.; Abspoel, L.; Kolstein, M.H.

    2012-01-01

    The assessment of the structural safety of existing br idges and viaducts becomes increasingly important in many countries owing to an increase in traffic loads. Most existing standards, however, are developed for the design of new structures. For this reason, an assessment method for determining

  4. A regulatory view of the seismic assessment of existing nuclear structures in the United Kingdom

    International Nuclear Information System (INIS)

    Inkester, J.E.

    2001-01-01

    The paper describes the background to the seismic assessment of existing nuclear structures in the United Kingdom. Nuclear installations in this country were not designed specifically to resist earthquakes until the nineteen-seventies, although older plants were robustly constructed. The seismic capability of these older installations is now being evaluated as part of the periodic safety reviews which nuclear licensees are required to carry out. The regulatory requirements which set the framework for these studies are explained. The licensees' processes of hazard appraisal and examination of the response of the structure are briefly summarized. Regulatory views on some of the criteria used to judge the adequacy of safety are discussed. Finally the paper provides some comments on future initiatives and possible areas of development. (author)

  5. Influence of chemical composition of zirconium alloy E110 on embrittlement under LOCA conditions - Part 1: Oxidation kinetics and macrocharacteristics of structure and fracture

    Science.gov (United States)

    Nikulin, S. A.; Rozhnov, A. B.; Belov, V. A.; Li, E. V.; Glazkina, V. S.

    2011-11-01

    Exploratory investigations of the influence of alloying and impurity content in the E110 alloy cladding tubes on the behavior under conditions of Loss of Coolant Accidents (LOCA) has been performed. Three alloys of E110 type have been tested: E110 alloy of nominal composition Zr-1%Nb (E110), E110 alloy of modified composition Zr-1%Nb-0.12%Fe-0.13%O (E110M), E110 alloy of nominal composition Zr-1%Nb with reduced impurity content (E110G). Alloys E110 and E110M were manufactured on the electrolytic basis and alloy E110G was manufactured on the basis of zirconium sponge. The high temperature oxidation tests in steam ( T = 1100 °C, 18% of equivalent cladding reacted (ECR)) have been conducted, kinetics of oxidation was investigated. Quantitative research of structure and fracture macrocharacteristics was performed by means of optical and electron microscopy. The results received were compared with the residual ductility of specimens. The results of the investigation showed the existence of "breakaway oxidation" kinetics and white spalling oxide in E110 and E110M alloys while the specimen oxidation kinetics in E110G alloy was characterized by a parabolic law and specimens had a dense black oxide. Oxygen and iron alloying in the E110 alloy positively changed the macrocharacteristics of structure and fracture. However, in general, it did not improve the resistance to embrittlement in LOCA conditions apparently because of a strong impurity influence caused by electrolytic process of zirconium production.

  6. The influence of reciprocating sliding wear on the oxidation behaviour of Fe-12Cr steel

    International Nuclear Information System (INIS)

    Smith, A.F.

    1989-01-01

    Medium-chromium ferritic alloys are used extensively in advanced gas cooled reactors (AGRs). Under certain conditions these alloys can undergo breakaway oxidation in which the rate-limiting step is located at the oxide/metal interface rather than the more usual gas/oxide interface; this results in linear oxidation kinetics. Repeated removal of oxide layers can expose chromium-depleted metal to the oxidizing gas and promote nucleation of breakaway oxidation. The question has been addressed as to whether high temperature sliding wear processes can also disrupt the surface so as to make the material potentially susceptible to breakaway oxidation. High temperature reciprocating wear tests of Fe-12Cr material in both low and high pressure reactor gas have been carried out. As expected, compact adhesive load-bearing oxide and mixed oxide/metal beds form in wear regions. These contacting features wear at very low rates of less than 10 -16 m 3 (Nm) -1 . Preformed oxides wear at sufficiently low rates at high temperature as to preclude the possibility of exposure of the underlying metal to the reactor gas. It is thus unlikely that sliding wear processes will accelerate the tendency for initiation of breakaway oxidation. (author)

  7. The solution of location problems with certain existing facility structures

    DEFF Research Database (Denmark)

    Juel, Henrik; Love, Robert F.

    1983-01-01

    It is known that in the Euclidean distance case, the optimal minisum location of a new facility in relation to four existing facilities is at the intersection of the two lines joining two pairs of the facilities. The authors extend this concept to minisum problems having any even number of existing...... facilities and characterized by generalized distance norms...

  8. Effect of metallurgical factors on the oxidation of Zr - 1% Nb Alloy

    International Nuclear Information System (INIS)

    Soliman, H.M.

    1979-01-01

    The importance of study of the oxidation behaviour of zirconium and its niobium alloys arises from their suitability as cladding and structural materials in nuclear reactors and their use in oxidizing conditions. This work includes the oxidation behaviour of Zr - 1%Nb in both air and steam, and to less extent, zirconium was investigated in air. The effect of 1%Nb, oxidizing medium, fluoride ions contamination and thermal cycling on the oxidation behaviour has been investigated using weight gain, plastic deformation generated during oxidation, electron microscopy , metallography and X- ray techniques. The kinetics of oxidation of Zr-1%Nb alloy have been studied in the temperature range 500 - 1200 degree C and 500 - 900 degree C in both air and steam, respectively. The oxidation rate increases with temperature, Initially, the reaction proceeds with a decreasing rate ( mainly parabolic) followed by transition to a linear or acceleration, indicating breakaway. As the oxidation temperature increases, the time to breakaway transition decreases

  9. Factor structure of self-reported clinical disorders and personality disorders : A review of the existing literature and a factor analytical study

    NARCIS (Netherlands)

    Bachrach, N.; Croon, M.A.; Bekker, M.H.J.

    2012-01-01

    Objectives The aim of this research is to add to the current understanding of the latent factor structure of personality disorders by performing a review of the existing literature (Study 1) and a factor analytical study on the factor structure and the relationship between self-reported Axis I and

  10. Existence problem of proton semi-bubble structure in the 2{sub 1}{sup +} state of {sup 34}Si

    Energy Technology Data Exchange (ETDEWEB)

    Wu, Feng [China Institute of Atomic Energy, Beijing (China); Sichuan University, Key Laboratory of Radiation Physics and Technology of Ministry of Education, School of Physics Science and Technology, Chengdu (China); Bai, C.L. [Sichuan University, Key Laboratory of Radiation Physics and Technology of Ministry of Education, School of Physics Science and Technology, Chengdu (China); Yao, J.M. [University of North Carolina, Department of Physics and Astronomy, Chapel Hill, NC (United States); Southwest University, School of Physical Science and Technology, Chongqing (China); Zhang, H.Q.; Zhang, X.Z. [China Institute of Atomic Energy, Beijing (China)

    2017-09-15

    The fully self-consistent Hartree-Fock (HF) plus random phase approximation (RPA) based on Skyrme-type interaction is used to study the existence problem of proton semi-bubble structure in the 2{sub 1}{sup +} state of {sup 34}Si. The experimental excitation energy and the transition strength of the 2{sub 1}{sup +} state in {sup 34}Si can be reproduced quite well. The tensor effect is also studied. It is shown that the tensor interaction has a notable impact on the excitation energy of the 2{sub 1}{sup +} state and a small effect on the B(E2) value. Besides, its effect on the density distributions in the ground and 2{sub 1}{sup +} state of {sup 34}Si is negligible. Our present results with T36 and T44 show that the 2{sub 1}{sup +} state of {sup 34}Si is mainly caused by proton transition from π1d{sub 5/2} orbit to π2s{sub 1/2} orbit, and the existence of a proton semi-bubble structure in this state is very unlikely. (orig.)

  11. Code structure for U-Mo fuel performance analysis in high performance research reactor

    Energy Technology Data Exchange (ETDEWEB)

    Jeong, Gwan Yoon; Cho, Tae Won; Lee, Chul Min; Sohn, Dong Seong [Ulsan National Institute of Science and Technology, Ulsan (Korea, Republic of); Lee, Kyu Hong; Park, Jong Man [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2015-05-15

    A performance analysis modeling applicable to research reactor fuel is being developed with available models describing fuel performance phenomena observed from in-pile tests. We established the calculation algorithm and scheme to best predict fuel performance using radio-thermo-mechanically coupled system to consider fuel swelling, interaction layer growth, pore formation in the fuel meat, and creep fuel deformation and mass relocation, etc. In this paper, we present a general structure of the performance analysis code for typical research reactor fuel and advanced features such as a model to predict fuel failure induced by combination of breakaway swelling and pore growth in the fuel meat. Thermo-mechanical code dedicated to the modeling of U-Mo dispersion fuel plates is being under development in Korea to satisfy a demand for advanced performance analysis and safe assessment of the plates. The major physical phenomena during irradiation are considered in the code such that interaction layer formation by fuel-matrix interdiffusion, fission induced swelling of fuel particle, mass relocation by fission induced stress, and pore formation at the interface between the reaction product and Al matrix.

  12. Structural acceptance criteria for the evaulation of existing double-shell waste storage tanks located at the Hanford site, Richland, Washington

    International Nuclear Information System (INIS)

    Julyk, L.J.; Day, A.D.; Dyrness, A.D.; Moore, C.J.; Peterson, W.S.; Scott, M.A.; Shrivastava, H.P.; Sholman, J.S.; Watts, T.N.

    1995-09-01

    The structural acceptance criteria contained herein for the evaluation of existing underground double-shell waste storage tanks located at the Hanford Site is part of the Life Management/Aging Management Program of the Tank Waste Remediation System. The purpose of the overall life management program is to ensure that confinement of the waste is maintained over the required service life of the tanks. Characterization of the present condition of the tanks, understanding and characterization of potential degradation mechanisms, and development of tank structural acceptance criteria based on previous service and projected use are prerequisites to assessing tank integrity, to projecting the length of tank service, and to developing and applying prudent fixes or repairs. The criteria provided herein summarize the requirements for the analysis and structural qualification of the existing double-shell tanks for continued operation. Code reconciliation issues and material degradation under aging conditions are addressed. Although the criteria were developed for double-shell tanks, many of the provisions are equally applicable to single-shell tanks. However, the criteria do not apply to the evaluation of tank appurtenances and buried piping

  13. The influence of reciprocating sliding wear on the oxidation behaviour of Fe-12Cr steel

    International Nuclear Information System (INIS)

    Smith, A.F.

    1988-04-01

    Medium-chromium ferritic alloys are used extensively in the boiler and core sections of advanced gas cooled reactors. It was discovered in the early 1970s, that under certain conditions these alloys could undergo the phenomenon known as breakaway oxidation. In this type of oxidation the rate limiting step is located at the oxide/metal interface rather than the more usual gas/oxide interface and results in linear oxidation kinetics. It has been shown that repeated removal of oxide layers can expose chromium depleted metal to the oxidising gas and promote nucleation of breakaway oxidation. The question has been addressed as to whether high temperature sliding wear processes can also disrupt the surface so as to make the material potentially susceptible to breakaway oxidation. To this end high temperature reciprocating wear of Fe-12Cr material in both low and high pressure reactor gas has been investigated. (author)

  14. Feasibility and safety of a novel in vivo model to assess playground falls in children.

    Science.gov (United States)

    Ehrlich, Peter F; Young, Justin G; Ulin, Sheryl; Wooley, Charles; Armstrong, Thomas J; Buschmann, Bethany; Galecki, Andrzej; Ashton-Miller, James A

    2013-07-01

    Falls are the leading cause of nonfatal unintentional injuries among hospitalized children with playground equipment accounting for more than 50%. National standards for playground rung and rail design exist, but there a lack of in vivo models available to test these standards. We developed a novel in vivo model to test rung and rail design. We report the feasibility and safety of the model. A device was built to simulate children hanging onto a playground bar until their hand slips off. This was defined as breakaway strength. The handle unit was mounted on a vertical cable that was mechanically raised and lowered using a linear actuator controlled by the experimenter. The unit was padded and contained a video camera that recorded the posture of the hand during each trial. Breakaway force and torque were recorded as they held onto the handle by LabView software. In addition, standard anthropometrics and grip strength were recorded. Biomedical engineering approved the device. There were 425 eligible students aged 5 years to 11 years. Of these, 93% (397) participated (212 males and 185 females). Ninety-nine percent (396 of 397) completed all three experimental stations, one declined because of fear. There were no injuries and no falls. Average time to complete the study was 22 ± 0.5 minutes. Ninety-one percent of participants were right handed; the ethnicity was representative of the local area with 79% being white. Mean ± SD height, weight, and body mass index for the 397 participants were 1.28 ± 0.11 m, 28.0 ± 8.12 kg, and 16.31 ± 2.59 kg/m², respectively. Hand size, grip strength, and maximum breakaway force increased with age. This model is safe and feasible and maybe a viable method to assess rung and rail design for playgrounds.

  15. On integration of plug-in hybrid electric vehicles into existing power system structures

    International Nuclear Information System (INIS)

    Galus, Matthias D.; Zima, Marek; Andersson, Goeran

    2010-01-01

    Plug-in hybrid electric vehicles (PHEVs) represent one option for the electrification of private mobility. In order to efficiently integrate PHEVs into power systems, existing organizational structures need to be considered. Based on procedures of power systems planning and operation, actors are identified whose operational activities will be affected by PHEV integration. Potential changes and challenges in the actors' long- and short term planning activities are discussed. Further, a PHEV operation state description is developed which defines vehicle operation states from the power system point of view integrating uncontrolled, controlled recharging and vehicle to grid (V2G) utilization in one single framework. Future PHEV managing entities, such as aggregators, can use this framework for planning and operation activities including load management and V2G. This operational state description could provide a solution for future short term planning challenges of PHEVs and an aegis for various routes of current research, which to date have been weakly linked to each other.

  16. Oxidation kinetics and auger microprobe analysis of some oxidized zirconium alloys

    International Nuclear Information System (INIS)

    Ploc, R.A.

    1989-01-01

    Oxidation kinetics at 300 o C in dry oxygen of 0.5 wt% binary alloys of iron, nickel, and chromium in zirconium were determined for several surface preparations. Further, chemical profiles of the oxides as they existed on the matrix and on the precipitates were obtained by sputtering and Auger electron analysis. The appearance of 'breakaway' oxidation was controlled by the surface finish of the alloy, a variable that could be used to eliminate the phenomenon for all alloys except the Zr/Ni binary, which required β-quenching to accomplish the same purpose. (author)

  17. Longitudinal-transverse liquid filtration in an annular heat-liberating medium

    International Nuclear Information System (INIS)

    Akhramovich, A.P.; Kolos, V.P.; Sorokin, V.N.

    1987-01-01

    The authors interpret experimental flow visualization data and construct a flow model for coolant filtration and flow in a layered granular heat exchange material for implementation in a reactor cooling system. Breakaway flow zones close to the ends of a layer in longitudinal-transverse liquid filtration are observed. In a linear approximation the problem of determining the form of the ends of the layer for which there is no flow breakaway is solved. The model is tested against experimental data for water and a nitrogen tetroxide coolant

  18. Proposal to negotiate amendments to an existing contract for the supply of steel structures for the LHC shafts, tunnels, caverns and experimental areas

    CERN Document Server

    2005-01-01

    This document concerns the proposal to negotiate amendments to an existing contract for the supply of additional steel structures for the LHC shafts, tunnels, caverns and experimental areas. For the reasons explained in this document, the Finance Committee is invited to approve amendments to the existing contract with the firm INIZIATIVE INDUSTRIALI (IT) for the supply of additional steel structures for the LHC shafts, tunnels, caverns and experimental areas for an amount of 500 000 euros (775 000 Swiss francs), subject to revision for inflation, bringing the total to 6 525 745 euros (10 114 905 Swiss francs), subject to revision for inflation. The amounts in Swiss francs have been calculated using the present rate of exchange.

  19. ANN Model for Predicting the Impact of Submerged Aquatic Weeds Existence on the Hydraulic Performance of Branched Open Channel System Accompanied by Water Structures

    International Nuclear Information System (INIS)

    Abdeen, Mostafa A. M.; Abdin, Alla E.

    2007-01-01

    The existence of hydraulic structures in a branched open channel system urges the need for considering the gradually varied flow criterion in evaluating the different hydraulic characteristics in this type of open channel system. Computations of hydraulic characteristics such as flow rates and water surface profiles in branched open channel system with hydraulic structures require tremendous numerical effort especially when the flow cannot be assumed uniform. In addition, the existence of submerged aquatic weeds in this branched open channel system adds to the complexity of the evaluation of the different hydraulic characteristics for this system. However, this existence of aquatic weeds can not be neglected since it is very common in Egyptian open channel systems. Artificial Neural Network (ANN) has been widely utilized in the past decade in civil engineering applications for the simulation and prediction of the different physical phenomena and has proven its capabilities in the different fields. The present study aims towards introducing the use of ANN technique to model and predict the impact of submerged aquatic weeds existence on the hydraulic performance of branched open channel system. Specifically the current paper investigates a branched open channel system that consists of main channel supplies water to two branch channels that are infested by submerged aquatic weeds and have water structures such as clear over fall weirs and sluice gates. The results of this study showed that ANN technique was capable, with small computational effort and high accuracy, of predicting the impact of different infestation percentage for submerged aquatic weeds on the hydraulic performance of branched open channel system with two different hydraulic structures

  20. High-temperature steam-oxidation behavior of Zr-1Nb-1Sn-0.1Fe cladding tube at temperatures of 800-1000

    International Nuclear Information System (INIS)

    Lee, Cheol Min; Cho, Tae Won; Jeong, Gwan Yoon; Kim, Mi Jin; Kim, Ji Hyeon; Lee, Hee Jae; Sohn, Dong Seong; Mok, Yong Kyoon

    2016-01-01

    To prevent cladding failure, NRC issued a regulation Title 10 § 50.46, which specifies cladding temperature of 1204 .deg. C and 17% ECR should not be exceeded. The fundamental reason of the mechanical degradation of cladding is the formation of the oxide which is brittle. Theoretically, the oxide layer is formed following parabolic rate. However, from many experiments, sub-parabolic rates are often observed. There have been many suggestions so far; chemical and stress gradient across the oxide layer could initiate the sub-parabolic rate, the phase transformation of Zirconium dioxide from tetragonal to monoclinic could be the reason, change of the grain size of Zirconium dioxide could cause the cubic oxidation rate, and there is a suggestion that if electron migration is the major mechanism of the oxide growth, then the subparabolic rate can show up. However, the reason why the sub-parabolic rate appears is still not certain. Another important degradation mechanism is breakaway oxidation. A clear explanation that why the breakaway oxidation appears is still not clear. Most of the people believe the phase transformation of Zirconium dioxide cause instability within the oxide, which causes breakaway oxidation to appear. However, how much effect is caused from the phase transformation is not so sure. In this study, detailed analysis about the oxidation kinetics and the breakaway oxidation of Zr-1Nb-1Sn- 0.1Fe were carried out at temperatures between 800 - 1000 .deg. C.

  1. Radiation hardening revisited: Role of intracascade clustering

    DEFF Research Database (Denmark)

    Singh, B.N.; Foreman, A.J.E.; Trinkaus, H.

    1997-01-01

    be explained in terms of conventional dispersed-barrier hardening because (a) the grown-in dislocations are not free, and (b) irradiation-induced defect clusters are not rigid indestructible Orowan obstacles. A new model called 'cascade-induced source hardening' is presented where glissile loops produced...... directly in cascades are envisaged to decorate the grown-in dislocations so that they cannot act as dislocation sources. The upper yield stress is related to the breakaway stress which is necessary to pull the dislocation away from the clusters/loops decorating it. The magnitude of the breakaway stress has...

  2. On the effectiveness of smart technologies in the seismic protection of existing buildings Part I: Masonry structures

    International Nuclear Information System (INIS)

    Mandara, A.; Ramundo, F.; Spina, G.

    2008-01-01

    The first part of a study concerning innovative intervention techniques for dissipate a share of the input seismic energy compatible with the preservation of existing buildings, including historical and monumental constructions, is presented in this paper. The case of a typical scheme of a long-bay box-like masonry building fitted with a dissipative floating roof is analyzed. In the examined building a wide simulation analysis has shown the achievement of a very satisfying performance. Furthermore, the effectiveness of the system can be maximized by means of active or semi-active devices implemented in the floating roof and a significant reduction of the seismic impact on the building can be obtained compared with non-controlled or simply passively controlled structure. The results prove the remarkable increase of the energy dissipation capability of the system, as well as the reduction of structural damage, independently of any specific strengthening intervention

  3. Existence and structure of rare-earth mono-carbides: study of their low-temperature magnetic properties; Existence et structure des monocarbures de terres rares. Etude de leurs proprietes magnetiques a basses temperatures

    Energy Technology Data Exchange (ETDEWEB)

    Lallement, R [Commissariat a l' Energie Atomique, Centre d' Etudes Nucleaires de Fontenay-aux-Roses, 92 (France)

    1966-07-01

    There are two types of rare earth carbides, the first one is face-centered cubic, stable at high temperature, and very hypo-stoichiometric (formula MC{sub x} with 0.35 < x < 0.65); the other is rhombohedric, stable at lower temperature, with a formula M{sub 2}C. These two carbides are magnetically ordered at low temperatures (ferro or ferri-magnetism). They are highly anisotropic. A great part of the electric and magnetic properties can be explained from the following ideas: the M{sup 3+} ions are coupled via the conduction electrons, there are more conduction electrons in the carbides than in the metals, and there is some local order around the transition temperatures. (author) [French] Nous avons mis en evidence l'existence de deux carbures de terres rares, l'un de formule MC{sub x} (0,35 < x < 0,65) de structure cubique a faces centrees, stable a haute temperature, l'autre de formule M{sub 2}C, de structure rhomhoedrique, stable a temperature moyenne. Ces deux types de carbures presentent des phenomenes d'ordre magnetique a basses temperatures (ferro ou ferrimagnetisme). Ils sont caracterises par une forte anisotropie magnetique. Une grande partie des proprietes electriques et magnetiques s'explique a partir des hypotheses suivantes: a) Les ions M{sup 3+} sont couples entre eux par l'intermediaire des electrons de conduction; b) Le nombre d'electrons de conduction dans les carbures est plus grand que dans les metaux; c) Autour des temperatures de transition se manifestent des phenomenes d'ordre local. (auteur)

  4. Application of advanced non-destructive testing to evaluate the foundation depth of the existing structures

    International Nuclear Information System (INIS)

    Nguyen Le Son; Nguyen Phuoc Lan; Pham The Hung; Vu Huy Thuc; Phan Chanh Vu; Bui Xuan Huy; Tran Thanh Luan; Nguyen Kien Chinh; Le Danh Chuan

    2004-01-01

    The applications of Parallel Seismic Test to evaluate deep foundations of the existing structures are still new in Vietnam. Under the framework of the basic VAEC project (2003) and project VIE/8/013, the parallel seismic test method (PSM) was evaluated at Center for Nuclear Techniques, Hochiminh City. Background information on principle and general description of the method as it is typically applied in the evaluation of deep foundations are also summarized. A suitable test site was selected, where the foundation depths can be controlled for the parallel seismic tests were conducted by impacting the driven piles, and the travel times down the pile, through the soil, to a receiver located in an adjacent water-filled borehole were measured. The primary objective of the test program is to evaluated the accuracy of method in determining the pile length, to evaluate the capabilities of the method and the equipped system SPL-97, to define the type of material which comprises a deep foundation, the distance of the compression wave can travel through the adjacent soil before the signal attenuates beyond recognition and the ware velocities in the various soil strata encountered. The parallel seismic testing program is described and results are presented. Parallel seismic tests, as conventionally practiced, i.e. with short distance between a structure and an access hole, can be used to define the bottom of the piles, as well as to identify the material type from the computed velocity in the structural material. The conventional approach of using changes of slop of the plot versus first arrival to identify the bottom of a deep foundation works best when the piles are in a soil with uniform stiffness and the accuracy of the evaluated depths can be obtained about ± 0.5 m. Supplementing this approach of interpretation by the examining the amplitudes of the first arrival on a plot with the same scale for all records allows one to better interpret signals in more common

  5. Seismic assessment of existing nuclear chemical plants

    International Nuclear Information System (INIS)

    Merriman, P.A.

    1997-01-01

    This paper outlines the generic approach to the seismic assessment of existing structures. It describes the role of the safety case in determining the studies carried out by the functional departments on individual projects. There is an emphasis on the role of existing information and material tests to provide realistic properties for analysis to account for possible degradation effects. Finally, a case study of a concrete containment cell is shown to illustrate the approach. (author)

  6. Earthquake resistant measures of existing structures by TRTA; Eidan chikatetsu ni okeru kisetsu doboku kozobutsu no taishin taisaku

    Energy Technology Data Exchange (ETDEWEB)

    Miyata, N.

    1997-08-10

    Seismic countermeasures for the existing structures are introduced on the main item: reinforcement of open-cut tunnel RC center pillars as well as on reinforcement of rigid frame viaduct pillars and installation of a device for prevention of viaduct falling. First, for reinforcing open-cut tunnel center pillars, design was devised so as to be suitable to construction environment in the subway yard. Important reinforcement materials are steel and filling materials; SS and a self-leveling material for building construction were chosen. The following construction work procedures are explained based on the actual construction: removal of interior materials of existing pillars and measurement of the actual size, high pressure water washing, steel plate fabrication, plate delivery to the yard, installation of steel plates, filler filling, painting. Next, on reinforcement of viaduct pillars on the ground, the reinforcement design concept is basically same as in the open-cut tunnel. Points of difference in design and construction are explained. On the countermeasure for prevention of viaduct falling for girder bridges without the falling prevention, countermeasure investigation and design work or installation work are being carried out. Seismic resistance evaluation and design of existing bridges, and construction work are explained. 13 figs., 1 tab.

  7. Analysis of existing structure and emissions of wood combustion plants for the production of heat and electricity in Bavaria

    International Nuclear Information System (INIS)

    Joa, Bettina

    2014-01-01

    This work deals with the detailed analysis of the existing structure of all Bavarian wood burning plants for the generation of heat and electricity as well as the determination of the resulting emission emissions in 2013. The number of wood burning plants in the single-chamber fireplaces, wood central heating and wood-fired heating plants which are in operation in the year 2013 were determined, and how many plants are existing in the various areas like pellet stoves, traditional ovens, wood-burning fireplace, pellet central heating systems, wood chips central heating systems, fire-wood central heating systems, wood combined heat and power plant (electricity and heat) and wood power plants (heat). In addition, the regional distribution of the wood burning plants in the Bavarian governmental districts is investigated as well as the type and amount of energy produced by them (heat, electricity). [de

  8. Oxidation limited lifetime of Ni-Base metal foams in the temperature range 700-900 C

    Energy Technology Data Exchange (ETDEWEB)

    Chyrkin, Anton; Singheiser, Lorenz; Quadakkers, Willem Joseph [Forschungszentrum Juelich GmbH, IEF-2, Juelich (Germany); Schulze, Sebastian Leif; Bleck, Wolfgang [Department of Ferrous Metallurgy, RWTH Aachen University, Aachen (Germany); Piron-Abellan, Javier [Vallourec Mannesmann Tubes, Duesseldorf (Germany)

    2010-09-15

    INCONEL 625 metal foams produced from alloy powder by the slip-reaction-foam-sinter-process are tested in respect to cyclic oxidation behavior in air in the temperature range 700-900 C. The structure of the oxide scales formed on the foam particles is characterized using optical microscopy and SEM/EDX analysis. Main emphasis is put on studying the oxidation limited lifetimes of the foams as function of temperature and foam microstructure. It is shown that mechanical disintegration during long term oxidation at the highest test temperatures is caused by a critical depletion of the Cr content in the alloy as a result of the growth of the initially formed surface chromia layer. This results in chemical breakaway due to accelerated oxide growth of voluminous Ni-rich oxide on chromium exhausted alloy particles. Lifetime modeling based on calculation of Cr-depletion in the alloy at the oxide/metal interface of each individual foam particle using the DICTRA software is in good agreement with the experimentally determined values of the time to breakaway. (Copyright copyright 2010 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  9. Why preeclampsia still exists?

    Science.gov (United States)

    Chelbi, Sonia T; Veitia, Reiner A; Vaiman, Daniel

    2013-08-01

    Preeclampsia (PE) is a deadly gestational disease affecting up to 10% of women and specific of the human species. Preeclampsia is clearly multifactorial, but the existence of a genetic basis for this disease is now clearly established by the existence of familial cases, epidemiological studies and known predisposing gene polymorphisms. PE is very common despite the fact that Darwinian pressure should have rapidly eliminated or strongly minimized the frequency of predisposing alleles. Consecutive pregnancies with the same partner decrease the risk and severity of PE. Here, we show that, due to this peculiar feature, preeclampsia predisposing-alleles can be differentially maintained according to the familial structure. Thus, we suggest that an optimal frequency of PE-predisposing alleles in human populations can be achieved as a result of a trade-off between benefits of exogamy, importance for maintaining genetic diversity and increase of the fitness owing to a stable paternal investment. Copyright © 2013 Elsevier Ltd. All rights reserved.

  10. Performance evaluation of existing building structure with pushover analysis

    Science.gov (United States)

    Handana, MAP; Karolina, R.; Steven

    2018-02-01

    In the management of the infrastructure of the building, during the period of buildings common building damage as a result of several reasons, earthquakes are common. The building is planned to work for a certain service life. But during the certain service life, the building vulnerable to damage due to various things. Any damage to cultivate can be detected as early as possible, because the damage could spread, triggering and exacerbating the latest. The newest concept to earthquake engineering is Performance Based Earthquake Engineering (PBEE). PBEE divided into two, namely Performance Based Seismic Design (PBSD) and Performance Based Seismic Evaluation (PBSE). Evaluation on PBSE one of which is the analysis of nonlinear pushover. Pushover analysis is a static analysis of nonlinear where the influence of the earthquake plan on building structure is considered as burdens static catch at the center of mass of each floor, which it was increased gradually until the loading causing the melting (plastic hinge) first within the building structure, then the load increases further changes the shapes of post-elastic large it reached the condition of elastic. Then followed melting (plastic hinge) in the location of the other structured.

  11. Seismic reevaluation of existing nuclear power plants

    International Nuclear Information System (INIS)

    Hennart, J.C.

    1978-01-01

    The codes and regulations governing Nuclear Power Plant seismic analysis are continuously becoming more stringent. In addition, design ground accelerations of existing plants must sometimes be increased as a result of discovery of faulting zones or recording of recent earthquakes near the plant location after plant design. These new factors can result in augmented seismic design criteria. Seismic reanalysius of the existing Nuclear Power Plant structures and equipments is necessary to prevent the consequences of newly postulated accidents that could cause undue risk to the health or safety of the public. This paper reviews the developments of seismic analysis as applied to Nuclear Power Plants and the methods used by Westinghouse to requalify existing plants to the most recent safety requirements. (author)

  12. Existence of undiscovered Uranian satellites

    International Nuclear Information System (INIS)

    Boice, D.C.

    1986-04-01

    Structure in the Uranian ring system as observed in recent occultations may contain indirect evidence for the existence of undiscovered satellites. Using the Alfven and Arrhenius (1975, 1976) scenario for the formation of planetary systems, the orbital radii of up to nine hypothetical satellites interior to Miranda are computed. These calculations should provide interesting comparisons when the results from the Voyager 2 encounter with Uranus are made public. 15 refs., 1 fig., 1 tab

  13. EDF'S ''OMF-structures'' RI-ISI process: overview of the methodology, applications and comparison with the other existing RI-ISI initiatives

    International Nuclear Information System (INIS)

    Codron, P.; Lauriot, B.; Dubreuil-Chambardel, A.

    2001-01-01

    The OMF-Structures process has been developed by EDF in order to optimise the maintenance of piping components. The principles of the OMF-Structures are consistent with the RCM concepts in EDF's OMF process (applied to active components). Several applications of this process have been performed. This paper also presents several applications which have been performed, notably on the AFW, RHR, and HPSI/LPSI systems of EDF's 900 MW PWR plants. These applications led to propose optimised preventive maintenance programs for these systems. These updated preventive maintenance programs confirmed and justified a large proportion of existing maintenance, despite some inspection tasks were suppressed and some inspection tasks were added. Globally, these new programs guarantee a better safety level, insuring that preventive maintenance is applied on piping segments where risks are concentrated. A comparative evaluation of the OMF-Structures process with the EPRI and WOG/ASME RI-ISI methodologies has been performed. This comparison demonstrated the consistence of the OMF-Structures principles and selection criteria with the other RI-ISI processes. (author)

  14. Economic and Thermal Evaluation of Different Uses of an Existing Structure in a Warm Climate

    Directory of Open Access Journals (Sweden)

    Delia D’Agostino

    2017-05-01

    Full Text Available Accounting for nearly 40% of final energy consumption, buildings are central to European energy policy. The Directive on Energy Performance of Buildings establishes a benchmarking system known as cost-optimality to set minimum energy performance requirements in new and existing buildings. This paper applies the cost-optimal methodology to an existing structure located in the Mediterranean area (Southern Italy. The building is composed of two units that have been considered for different uses: hotel and multi-residential. Several energy efficiency and renewable measures have been implemented both individually and as part of packages of measures. The cost-optimal solution has been identified as able to optimize energy consumption and costs from financial and macroeconomic perspectives. The first reference building (hotel use shows a maximum reduction of primary energy and CO2 emission of about 42%, falling within the CasaClima energy class D, while the second reference building (residential use achieves a value of 88% for primary energy and 85% for CO2 emissions, falling into class B. Thermal dispersions through the envelope can be limited using a suitable combination of insulating materials while a variety of technical variants are selected, such as VRF (variant refrigerant flow systems, heat pumps with fan coils associated with controlled mechanical ventilation, solar thermal and photovoltaic. This paper illustrates the development of energy retrofit projects, in order to reach a balance between efficiency measures and costs for a building having two different uses, providing guidance to similar case studies related to a warm climate.

  15. Structure of Unsteady Partially Premixed Flames and the Existence of State Relationships

    Directory of Open Access Journals (Sweden)

    Suresh K. Aggarwal

    2009-09-01

    Full Text Available In this study, we examine the structure and existence of state relationships in unsteady partially premixed flames (PPFs subjected to buoyancy-induced and external perturbations. A detailed numerical model is employed to simulate the steady and unsteady two-dimensional PPFs established using a slot burner under normal and zero-gravity conditions. The coflow velocity is parametrically varied. The methane-air chemistry is modeled using a fairly detailed mechanism that contains 81 elementary reactions and 24 species. Validation of the computational model is provided through comparisons of predictions with nonintrusive measurements. The combustion proceeds in two reaction zones, one a rich premixed zone and the other a nonpremixed zone. These reaction zones are spatially separated, but involve strong interactions between them due to thermochemistry and scalar transport. The fuel is mostly consumed in the premixed zone to produce CO and H2, which are transported to and consumed in the nonpremixed zone. The nonpremixed zone in turn provides heat and H-atoms to the premixed zone. For the range of conditions investigated, the zero-g partially premixed flames exhibit a stable behavior and a remarkably strong resistance to perturbations. In contrast, the corresponding normal-gravity flames exhibit oscillatory behavior at low coflow velocities but a stable behavior at high coflow velocities, and the behavior can be explained in terms of a global and convective instabilities. The effects of coflow and gravity on the flames are characterized through a parameter VR, defined as the ratio of coflow velocity to jet velocity. For VR ≤ 1 (low coflow velocity regime, the structures of both 0- and 1-g flames are strongly sensitive to changes in VR, while they are only mildly affected by coflow in the high coflow velocity regime (VR > 1. In addition, the spatio-temporal characteristics of the 0- and 1-g flames are markedly different in the first regime, but are

  16. Comparison between zircaloy oxidation in steam and air surroundings

    International Nuclear Information System (INIS)

    Shawkat, M.E.; Hasaneln, H.; Ali, M.; Parlatan, Y.; Albasha, H.

    2013-01-01

    The available experimental data for Zircaloy oxidation in air were reviewed. The behavior of the oxidation kinetics at different temperature ranges was described. It was shown that maintaining the oxidation kinetics within the oxide pre-breakaway region can prevent elevated sheath temperatures due to the oxidation process during postulated accidents. The available correlations to model the oxidation kinetics for pre-breakaway region were reviewed and assessed. Zircaloy-air oxidation correlation based on Leistikow-Berg data was determined to be the most suitable correlation to model pre-breakaway kinetics and it was compared to Urbanic-Heidrick correlation which is widely used for Zircaloy oxidation in steam environment. The results showed that the energy release due to the Zircaloy-steam oxidation bounds the energy released due to Zircaloy-air oxidation up to a sheath temperature referred as the “crossover temperature”. Below this temperature, the impact of Zircaloy-air oxidation on fuel sheath temperature transient can be predicted conservatively using the Urbanic-Heidrick steam correlation. The crossover temperature was calculated for isothermal sheath heating as well as transient sheath heat-up assuming three linear heating rates of 0.6, 1.0, and 1.3 K/s. (author)

  17. Air oxidation of Zircaloy-4 in the 600-1000 °C temperature range: Modeling for ASTEC code application

    Science.gov (United States)

    Coindreau, O.; Duriez, C.; Ederli, S.

    2010-10-01

    Progress in the treatment of air oxidation of zirconium in severe accident (SA) codes are required for a reliable analysis of severe accidents involving air ingress. Air oxidation of zirconium can actually lead to accelerated core degradation and increased fission product release, especially for the highly-radiotoxic ruthenium. This paper presents a model to simulate air oxidation kinetics of Zircaloy-4 in the 600-1000 °C temperature range. It is based on available experimental data, including separate-effect experiments performed at IRSN and at Forschungszentrum Karlsruhe. The kinetic transition, named "breakaway", from a diffusion-controlled regime to an accelerated oxidation is taken into account in the modeling via a critical mass gain parameter. The progressive propagation of the locally initiated breakaway is modeled by a linear increase in oxidation rate with time. Finally, when breakaway propagation is completed, the oxidation rate stabilizes and the kinetics is modeled by a linear law. This new modeling is integrated in the severe accident code ASTEC, jointly developed by IRSN and GRS. Model predictions and experimental data from thermogravimetric results show good agreement for different air flow rates and for slow temperature transient conditions.

  18. Interactions of impurities with a moving grain boundary

    Energy Technology Data Exchange (ETDEWEB)

    Bauer, C L [Carnegie-Mellon Univ., Pittsburgh, Pa. (USA)

    1975-01-01

    Most theories developed to explain interaction of impurities with a moving grain boundary involve a uniform excess impurity concentration distributed along a planar grain boundary. As boundary velocity increases, the excess impurities exert a net drag force on the boundary until a level is reached whereat the drag force no longer can balance the driving force and breakaway of the boundary from these impurities occurs. In this investigation, assumptions of a uniform lateral impurity profile and a planar grain boundary shape are relaxed by allowing both forward and lateral diffusion of impurities in the vicinity of a grain boundary. It is found that the two usual regions (drag of impurities by, and breakaway of a planar grain boundary) are separated by an extensive region wherein a uniform lateral impurity profile and a planar grain boundary shape are unstable. It is suspected that, in this unstable region, grain boundaries assume a spectrum of more complex morphologies and that elucidation of these morphologies can provide the first definitive description of the breakaway process and insight to more complex phenomena such as solid-solution strengthening, grain growth and secondary recrystallization.

  19. The oxidation behaviour of Fe-9Cr-1Mo steels

    International Nuclear Information System (INIS)

    Rowlands, P.C.; Holmes, D.R.; Whittaker, A.; Brierley, R.A.; Garrett, J.C.P.

    1983-01-01

    The oxidation behaviour of Fe9Cr1Mo steels over a wide range of conditions covering likely operating environments has been determined. In particular the effects of temperature, gas composition and materials variables on production materials have been investigated. From this work the mechanisms of protective and breakaway corrosion have broadly been elucidated. The vital role of carbon deposition in the oxide and carburisation of the metal has been determined. Aspects of the breakaway and protective oxidation mechanisms have been incorporated into a statistical model for predicting breakaway initiation and boiler component life. The results obtained from the tube life calculations indicate very low probabilities of component failure for coolant gas compositions containing up to the equivalent of 825 vppm H 2 O and 1%CO. For a more aggressive gas at the upper limit of CO concentration (2%CO) there is a small probability of failure within 25 years for finned boiler tubes. Current work may in time allow these constraints composition to be relaxed. The information gained has been used in the design of Heysham II/Torness to reduce the probabilities of 9Cr component failure to insignificant levels. (author)

  20. Ontological Proofs of Existence and Non-Existence

    Czech Academy of Sciences Publication Activity Database

    Hájek, Petr

    2008-01-01

    Roč. 90, č. 2 (2008), s. 257-262 ISSN 0039-3215 R&D Projects: GA AV ČR IAA100300503 Institutional research plan: CEZ:AV0Z10300504 Keywords : ontological proofs * existence * non-existence * Gödel * Caramuel Subject RIV: BA - General Mathematics

  1. Extending existing structural identifiability analysis methods to mixed-effects models.

    Science.gov (United States)

    Janzén, David L I; Jirstrand, Mats; Chappell, Michael J; Evans, Neil D

    2018-01-01

    The concept of structural identifiability for state-space models is expanded to cover mixed-effects state-space models. Two methods applicable for the analytical study of the structural identifiability of mixed-effects models are presented. The two methods are based on previously established techniques for non-mixed-effects models; namely the Taylor series expansion and the input-output form approach. By generating an exhaustive summary, and by assuming an infinite number of subjects, functions of random variables can be derived which in turn determine the distribution of the system's observation function(s). By considering the uniqueness of the analytical statistical moments of the derived functions of the random variables, the structural identifiability of the corresponding mixed-effects model can be determined. The two methods are applied to a set of examples of mixed-effects models to illustrate how they work in practice. Copyright © 2017 Elsevier Inc. All rights reserved.

  2. A sampling strategy to establish existing plant configuration baselines

    International Nuclear Information System (INIS)

    Buchanan, L.P.

    1995-01-01

    The Department of Energy's Gaseous Diffusion Plants (DOEGDP) are undergoing a Safety Analysis Update Program. As part of this program, critical existing structures are being reevaluated for Natural Phenomena Hazards (NPH) based on the recommendations of UCRL-15910. The Department of Energy has specified that current plant configurations be used in the performance of these reevaluations. This paper presents the process and results of a walkdown program implemented at DOEGDP to establish the current configuration baseline for these existing critical structures for use in subsequent NPH evaluations. These structures are classified as moderate hazard facilities and were constructed in the early 1950's. The process involved a statistical sampling strategy to determine the validity of critical design information as represented on the original design drawings such as member sizes, orientation, connection details and anchorage. A floor load inventory of the dead load of the equipment, both permanently attached and spare, was also performed as well as a walkthrough inspection of the overall structure to identify any other significant anomalies

  3. Reserves in load capacity assessment of existing bridges

    Science.gov (United States)

    Žitný, Jan; Ryjáček, Pavel

    2017-09-01

    High percentage of all railway bridges in the Czech Republic is made of structural steel. Majority of these bridges is designed according to historical codes and according to the deterioration, they have to be assessed if they satisfy the needs of modern railway traffic. The load capacity assessment of existing bridges according to Eurocodes is however often too conservative and especially, braking and acceleration forces cause huge problems to structural elements of the bridge superstructure. The aim of this paper is to review the different approaches for the determination of braking and acceleration forces. Both, current and historical theoretical models and in-situ measurements are considered. The research of several local European state norms superior to Eurocode for assessment of existing railway bridges shows the big diversity of used local approaches and the conservativeness of Eurocode. This paper should also work as an overview for designers dealing with load capacity assessment, revealing the reserves for existing bridges. Based on these different approaches, theoretical models and data obtained from the measurements, the method for determination of braking and acceleration forces on the basis of real traffic data should be proposed.

  4. Structural Identification And Seismic Analysis Of An Existing Masonry Building

    International Nuclear Information System (INIS)

    Del Monte, Emanuele; Galano, Luciano; Ortolani, Barbara; Vignoli, Andrea

    2008-01-01

    The paper presents the diagnostic investigation and the seismic analysis performed on an ancient masonry building in Florence. The building has historical interest and is subjected to conservative restrictions. The investigation involves a preliminary phase concerning the research of the historic documents and a second phase of execution of in situ and laboratory tests to detect the mechanical characteristics of the masonry. This investigation was conceived in order to obtain the 'LC2 Knowledge Level' and to perform the non-linear pushover analysis according to the new Italian Standards for seismic upgrading of existing masonry buildings

  5. Proposed Assessment of Dynamic Resistance of the Existing Industrial Portal Frame Building Structures to the Impact of Mining Tremors

    Science.gov (United States)

    Rusek, Janusz; Kocot, Wojciech

    2017-10-01

    The article presents the method for assessing dynamic resistance of the existing industrial portal frame building structures subjected to mining tremors. The study was performed on two industrial halls of a reinforced concrete structure and a steel structure. In order to determine the dynamic resistances of these objects, static and dynamic numerical analysis in the FEA environment was carried out. The scope of numerical calculations was adapted to the guidelines contained in the former and current design standards. This allowed to formulate the criteria, on the basis of which the maximum permissible value of the horizontal ground acceleration was obtained, constituting resistance of the analyzed objects. The permissible range of structural behaviour was determined by comparing the effects of load combinations adopted at the design stage with a seismic combination recognized in Eurocode 8. The response spectrum method was used in the field of dynamic analysis, taking into account the guidelines contained in Eurocode 8 and the guidelines of National. Finally, in accordance with the established procedure, calculations were carried out and the results for the two model portal frame buildings of reinforced concrete and steel structures were presented. The results allowed for the comparison of the dynamic resistance of two different types of material and design, and a sensitivity analysis with respect to their constituent bearing elements. The conclusions drawn from these analyses helped to formulate the thesis for the next stage of the research, in which it is expected to analyze a greater number of objects using a parametric approach, in relation to the geometry and material properties.

  6. Facilities improvement for sustainability of existing public office ...

    African Journals Online (AJOL)

    The study examined the building design features of a cosmopolitan public office building in Abuja. The features were classified into Spatial Plan, Structure and Facilities, to determine which of the 3 variables requires urgent sustainable improvement from end-users' perspective in existing public office buildings in developing ...

  7. Does GaH5 exist?

    Science.gov (United States)

    Speakman, Lucas D.; Turney, Justin M.; Schaefer, Henry F.

    2005-11-01

    The existence or nonexistence of GaH5 has been widely discussed [N. M. Mitzel, Angew. Chem. Int. Ed. 42, 3856 (2003)]. Seven possible structures for gallium pentahydride have been systematically investigated using ab initio electronic structure theory. Structures and vibrational frequencies have been determined employing self-consistent field, coupled cluster including all single and double excitations (CCSD), and CCSD with perturbative triples levels of theory, with at least three correlation-consistent polarized-valence-(cc-pVXZ and aug-cc-pVXZ) type basis sets. The X˜A'1 state for GaH5 is predicted to be weakly bound complex 1 between gallane and molecular hydrogen, with Cs symmetry. The dissociation energy corresponding to GaH5→GaH3+H2 is predicted to be De=2.05kcalmol-1. The H-H stretching fundamental is predicted to be v =4060cm-1, compared to the tentatively assigned experimental feature of Wang and Andrews [J. Phys. Chem. A 107, 11371 (2003)] at 4087cm-1. A second Cs structure 2 with nearly equal energy is predicted to be a transition state, corresponding to a 90° rotation of the H2 bond. Thus the rotation of the hydrogen molecule is essentially free. However, hydrogen scrambling through the C2v structure 3 seems unlikely, as the activation barrier for scrambling is at least 30kcalmol-1 higher in energy than that for the dissociation of GaH5 to GaH3 and H2. Two additional structures consisting of GaH3 with a dihydrogen bond perpendicular to gallane (C3v structure 4) and an in-plane dihydrogen bond [Cs(III) structure 5] were also examined. A C3v symmetry second-order saddle point has nearly the same energy as the GaH3+H2 dissociation limit, while the Cs(III) structure 5 is a transition structure to the C3v structure. The C4v structure 6 and the D3h structure 7 are much higher in energy than GaH3+H2 by 88 and 103kcalmol-1, respectively.

  8. Seismic review of existing nuclear power plants

    International Nuclear Information System (INIS)

    Yanev, P.I.; Mayes, R.L.; Jones, L.R.

    1975-01-01

    Because of developments in the fields of earthquake and structural engineering over the last two decades, the codes, standards and design criteria for Nuclear Power Plants and other critical structures have changed substantially. As a result, plants designed only a few years ago do not satisfy the requirements for new plants. Accordingly, the Regulatory Agencies are requiring owners of older Nuclear Power Plants to re-qualify the plants seismically, using codes, standards, analytical techniques and knowledge developed in recent years. Seismic review consists of three major phases: establishing the design and performance criteria, re-qualifying the structures, and re-qualifying the equipment. The authors of the paper have been recently involved in the seismic review of existing nuclear power plants in the United States. This paper is a brief summary of their experiences

  9. The Discovery of the Existence of the Absolute in Existential Metaphysics

    Directory of Open Access Journals (Sweden)

    Andrzej Maryniarczyk

    2016-12-01

    Full Text Available The article shows the way in which the discovery of the existence of the Absolute is made in existential metaphysics. This existential metaphysics provides us with knowledge about reality. It shows the content of the experience of being, the content given to us in the transcendentals. It also unveils the foundation of the rational order, which is given to us in the discovery of the first principles of the existence of being and of cognition. Metaphysics provides us also with knowledge concerning the structure of being. It shows us being as composite and plural; being which is “insufficient” in its structure and calls for an explanation. That being—that is problematized in existence, given to us in experience, and incompletely intelligible in itself—lifts us toward its ultimate “complement” and understanding, to the Absolute.

  10. Democracy in Russia: Trends and Implications for U.S. Interests

    National Research Council Canada - National Science Library

    Nichol, John

    2006-01-01

    .... Since then, Russians have faced increased government interference in elections and campaigns, restrictions on freedom of the media, large-scale human rights abuses in the breakaway Chechnya region...

  11. International symposium on seismic evaluation of existing nuclear facilities

    Energy Technology Data Exchange (ETDEWEB)

    Orbovic, N.; Bouchon, M. [Institut de Radioprotection et de Surete Nucleaire, IRSN, 92 - Fontenay aux Roses (France); Vendel, J.; Gelain, T. [IRSN/DPEA/SERAC, 91 - Gif sur Yvette (France)

    2003-10-01

    Below are summarized the works of Mrs N. Orbovic and M. Bouchon; B. Stojadinovic, N. Orbovic, M.Bouchon and J.T. Wiley; M. Bouchon, N. Orbovic and B. Foure; T. Gelain, F. Gensdarmes, R. Sestier-Carlin, J. Vendel and M. Bouchon dealing respectively with: 1) seismic assessment of existing nuclear facility: a case study position of the IRSN 2) static and dynamic evaluation of an existing nuclear facility reinforced concrete frame structure 3) experimental study of cracking of low-rise reinforced concrete shear walls 4) aeraulics study of crack networks on low-rise reinforced concrete walls subject to static cycling loading. The summaries are followed: 1) The Institute for Radioprotection and Nuclear Safety (IRSN) has the task of evaluating the seismic safety of existing building inventory in French nuclear facilities. Some of the existing structures are reinforced concrete frame buildings with masonry or reinforced concrete in-fill walls built during the 1960's, 70's and 80's following different building codes and seismic input data applicable at the time of construction. The studied building is a laboratory that was built in 1962. The building is composed of three different and independent blocks. The structure is a reinforced concrete frame with masonry in-fills and few stiff concrete elements. Moreover, the building contains an independent massive concrete cell. Structurally, the building has a number of irregularities. From the detailing standpoint, well known deficiencies of low-ductile reinforced concrete structures are evident especially, a lack of transverse reinforcement in the structural joints of the frame. A number of sensitivity studies were conducted using 2D and 3D linear models to evaluate seismic demand. Ambient vibration and regional earthquake records were used to check the soil nature and the existence or not of a possible site effect around the installation as well as to characterize the dynamic behavior of the building. 3D models

  12. Seismic capacities of existing nuclear power plant structures

    International Nuclear Information System (INIS)

    Wesley, D.A.; Hashimoto, P.S.; Narver, R.B.

    1983-01-01

    The paper presents a discussion of the more important conservatisms and some of the results obtained when this methodology has been applied to various nuclear plants. Results are shown for both BWR and PWR plants, on both rock and soil sites, and for plants and soil sites, and for plants that were designed in the late 1960s to plants that have yet to load fuel. Safe shutdown earthquake design levels of 0.1 g to 0.25 g were used for these plants. Overall median structural factors of safety for the lowest significant seismic failure capacity at each plant ranged from 3.5 to 8.5. The lowest containment-related failure capacity at each plant ranged from 4.6 to 31. The types of failure corresponding to each safety factor are also tabulated. (orig./HP)

  13. Stiff Columns as Liquefaction Mitigation Measure for Retrofit of Existing Buildings

    Directory of Open Access Journals (Sweden)

    Zaheer Ahmed Almani

    2012-10-01

    Full Text Available In this paper, ground reinforcement with jet grouted columns under shallow foundations of existing buildings was analysed using numerical modelling. This study is related with ground reinforcement by installing stiff jet grouted columns around the shallow foundations of existing building when the foundation soil is liquefied during an earthquake. The isolated shallow square footing pad supporting a typical simple frame structure was constructed on the reinforced ground with stiff jet grouted column rows at the shallow depth from the ground surface. This soil-structure system was modelled and analyzed as plane-strain using the FLAC (Fast Lagrangian Analysis of Continua 2D dynamic modelling and analysis software. The results showed that liquefaction-induced large settlement of shallow foundation of existing building can be reduced to tolerable limits by applying ground reinforcement with continuous rows vertical jet grouted columns adjacent to footing pad.

  14. 2D and 3D GPR imaging of structural ceilings in historic and existing constructions

    Science.gov (United States)

    Colla, Camilla

    2014-05-01

    GPR applications in civil engineering are to date quite diversified. With respect to civil constructions and monumental buildings, detection of voids, cavities, layering in structural elements, variation of geometry, of moisture content, of materials, areas of decay, defects, cracks have been reported in timber, concrete and masonry elements. Nonetheless, many more fields of investigation remain unexplored. This contribution gives an account of a variety of examples of structural ceilings investigation by GPR radar in reflection mode, either as 2D or 3D data acquisition and visualisation. Ceilings have a pre-eminent role in buildings as they contribute to a good structural behaviour of the construction. Primarily, the following functions can be listed for ceilings: a) they carry vertical dead and live loads on floors and distribute such loads to the vertical walls; b) they oppose to external horizontal forces such as wind loads and earthquakes helping to transfer such forces from the loaded element to the other walls; c) they contribute to create the box skeleton and behaviour of a building, connecting the different load bearing walls and reducing the slenderness and flexural instability of such walls. Therefore, knowing how ceilings are made in specific buildings is of paramount importance for architects and structural engineers. According to the type of building and age of construction, ceilings may present very different solutions and materials. Moreover, in existing constructions, ceilings may have been substituted, modified or strengthened due to material decay or to change of use of the building. These alterations may often go unrecorded in technical documentation or technical drawings may be unavailable. In many cases, the position, orientation and number of the load carrying elements in ceilings may be hidden or not be in sight, due for example to the presence of false ceilings or to technical plants. GPR radar can constitute a very useful tool for

  15. 76 FR 9376 - Proposed Extension of Existing Information Collection;

    Science.gov (United States)

    2011-02-17

    ... Extension of Existing Information Collection; Refuse Piles and Impoundment Structures, Recordkeeping and... surface installations. More specifically, these sections address refuse piles (30 CFR 77.215), and... combination of materials; and refuse piles are deposits of coal mine waste (other than overburden or spoil...

  16. Oxidation behavior of U-Si compounds in air from 25 to 1000 C

    Science.gov (United States)

    Sooby Wood, E.; White, J. T.; Nelson, A. T.

    2017-02-01

    The air oxidation behavior of U3Si2, USi, and U3Si5 is studied from room temperature to 1000 C. The onsets of breakaway oxidation for each compound are identified during synthetic air ramps to 1000 C using thermogravimetric analysis. Isothermal air oxidation tests are performed below and above the breakaway oxidation onset to discern the oxidation kinetic behavior of these candidate accident tolerant fuel forms. Uranium metal is tested in the same manner to provide a reference for the oxidation behavior. Thermogravimetric, x-ray diffraction, and scanning electron microscopy analysis are presented here along with a discussion of the oxidation behavior of these materials and the impact of the lack of oxidation resistance to their deployment as accident tolerant nuclear fuels.

  17. Estimation of the behavior factor of existing RC-MRF buildings

    Science.gov (United States)

    Vona, Marco; Mastroberti, Monica

    2018-01-01

    In recent years, several research groups have studied a new generation of analysis methods for seismic response assessment of existing buildings. Nevertheless, many important developments are still needed in order to define more reliable and effective assessment procedures. Moreover, regarding existing buildings, it should be highlighted that due to the low knowledge level, the linear elastic analysis is the only analysis method allowed. The same codes (such as NTC2008, EC8) consider the linear dynamic analysis with behavior factor as the reference method for the evaluation of seismic demand. This type of analysis is based on a linear-elastic structural model subject to a design spectrum, obtained by reducing the elastic spectrum through a behavior factor. The behavior factor (reduction factor or q factor in some codes) is used to reduce the elastic spectrum ordinate or the forces obtained from a linear analysis in order to take into account the non-linear structural capacities. The behavior factors should be defined based on several parameters that influence the seismic nonlinear capacity, such as mechanical materials characteristics, structural system, irregularity and design procedures. In practical applications, there is still an evident lack of detailed rules and accurate behavior factor values adequate for existing buildings. In this work, some investigations of the seismic capacity of the main existing RC-MRF building types have been carried out. In order to make a correct evaluation of the seismic force demand, actual behavior factor values coherent with force based seismic safety assessment procedure have been proposed and compared with the values reported in the Italian seismic code, NTC08.

  18. Wireless Smart Sensor Network System Using SmartBridge Sensor Nodes for Structural Health Monitoring of Existing Concrete Bridges

    Science.gov (United States)

    Gaviña, J. R.; Uy, F. A.; Carreon, J. D.

    2017-06-01

    There are over 8000 bridges in the Philippines today according to the Department of Public Works and Highways (DPWH). Currently, visual inspection is the most common practice in monitoring the structural integrity of bridges. However, visual inspections have proven to be insufficient in determining the actual health or condition of a bridge. Structural Health Monitoring (SHM) aims to give, in real-time, a diagnosis of the actual condition of the bridge. In this study, SmartBridge Sensor Nodes were installed on an existing concrete bridge with American Association of State Highway and Transportation Officials (AASHTO) Type IV Girders to gather vibration of the elements of the bridge. Also, standards on the effective installation of SmartBridge Sensor Nodes, such as location and orientation was determined. Acceleration readings from the sensor were then uploaded to a server, wherein they are monitored against certain thresholds, from which, the health of the bridge will be derived. Final output will be a portal or webpage wherein the information, health, and acceleration readings of the bridge will be available for viewing. With levels of access set for different types of users, the main users will have access to download data and reports. Data transmission and webpage access are available online, making the SHM system wireless.

  19. Proposed and existing passive and inherent safety-related structures, systems, and components (building blocks) for advanced light-water reactors

    International Nuclear Information System (INIS)

    Forsberg, C.W.; Moses, D.L.; Lewis, E.B.; Gibson, R.; Pearson, R.; Reich, W.J.; Murphy, G.A.; Staunton, R.H.; Kohn, W.E.

    1989-10-01

    A nuclear power plant is composed of many structures, systems, and components (SSCs). Examples include emergency core cooling systems, feedwater systems, and electrical systems. The design of a reactor consists of combining various SSCs (building blocks) into an integrated plant design. A new reactor design is the result of combining old SSCs in new ways or use of new SSCs. This report identifies, describes, and characterizes SSCs with passive and inherent features that can be used to assure safety in light-water reactors. Existing, proposed, and speculative technologies are described. The following approaches were used to identify the technologies: world technical literature searches, world patent searches, and discussions with universities, national laboratories and industrial vendors. 214 refs., 105 figs., 26 tabs

  20. Proposed and existing passive and inherent safety-related structures, systems, and components (building blocks) for advanced light-water reactors

    Energy Technology Data Exchange (ETDEWEB)

    Forsberg, C.W.; Moses, D.L.; Lewis, E.B.; Gibson, R.; Pearson, R.; Reich, W.J.; Murphy, G.A.; Staunton, R.H.; Kohn, W.E.

    1989-10-01

    A nuclear power plant is composed of many structures, systems, and components (SSCs). Examples include emergency core cooling systems, feedwater systems, and electrical systems. The design of a reactor consists of combining various SSCs (building blocks) into an integrated plant design. A new reactor design is the result of combining old SSCs in new ways or use of new SSCs. This report identifies, describes, and characterizes SSCs with passive and inherent features that can be used to assure safety in light-water reactors. Existing, proposed, and speculative technologies are described. The following approaches were used to identify the technologies: world technical literature searches, world patent searches, and discussions with universities, national laboratories and industrial vendors. 214 refs., 105 figs., 26 tabs.

  1. Stress Prediction for Distributed Structural Health Monitoring Using Existing Measurements and Pattern Recognition.

    Science.gov (United States)

    Lu, Wei; Teng, Jun; Zhou, Qiushi; Peng, Qiexin

    2018-02-01

    The stress in structural steel members is the most useful and directly measurable physical quantity to evaluate the structural safety in structural health monitoring, which is also an important index to evaluate the stress distribution and force condition of structures during structural construction and service phases. Thus, it is common to set stress as a measure in steel structural monitoring. Considering the economy and the importance of the structural members, there are only a limited number of sensors that can be placed, which means that it is impossible to obtain the stresses of all members directly using sensors. This study aims to develop a stress response prediction method for locations where there are insufficent sensors, using measurements from a limited number of sensors and pattern recognition. The detailed improved aspects are: (1) a distributed computing process is proposed, where the same pattern is recognized by several subsets of measurements; and (2) the pattern recognition using the subset of measurements is carried out by considering the optimal number of sensors and number of fusion patterns. The validity and feasibility of the proposed method are verified using two examples: the finite-element simulation of a single-layer shell-like steel structure, and the structural health monitoring of the space steel roof of Shenzhen Bay Stadium; for the latter, the anti-noise performance of this method is verified by the stress measurements from a real-world project.

  2. Influence of pre-existing basement faults on the structural evolution of the Zagros Simply Folded belt: 3D numerical modelling

    Science.gov (United States)

    Ruh, Jonas B.; Gerya, Taras

    2015-04-01

    The Simply Folded Belt of the Zagros orogen is characterized by elongated fold trains symptomatically defining the geomorphology along this mountain range. The Zagros orogen results from the collision of the Arabian and the Eurasian plates. The Simply Folded Belt is located southwest of the Zagros suture zone. An up to 2 km thick salt horizon below the sedimentary sequence enables mechanical and structural detachment from the underlying Arabian basement. Nevertheless, deformation within the basement influences the structural evolution of the Simply Folded Belt. It has been shown that thrusts in form of reactivated normal faults can trigger out-of-sequence deformation within the sedimentary stratigraphy. Furthermore, deeply rooted strike-slip faults, such as the Kazerun faults between the Fars zone in the southeast and the Dezful embayment and the Izeh zone, are largely dispersing into the overlying stratigraphy, strongly influencing the tectonic evolution and mechanical behaviour. The aim of this study is to reveal the influence of basement thrusts and strike-slip faults on the structural evolution of the Simply Folded Belt depending on the occurrence of intercrustal weak horizons (Hormuz salt) and the rheology and thermal structure of the basement. Therefore, we present high-resolution 3D thermo-mechnical models with pre-existing, inversively reactivated normal faults or strike-slip faults within the basement. Numerical models are based on finite difference, marker-in-cell technique with (power-law) visco-plastic rheology accounting for brittle deformation. Preliminary results show that deep tectonic structures present in the basement may have crucial effects on the morphology and evolution of a fold-and-thrust belt above a major detachment horizon.

  3. International symposium on seismic evaluation of existing nuclear facilities

    International Nuclear Information System (INIS)

    Orbovic, N.; Bouchon, M.; Vendel, J.; Gelain, T.

    2003-10-01

    Below are summarized the works of Mrs N. Orbovic and M. Bouchon; B. Stojadinovic, N. Orbovic, M.Bouchon and J.T. Wiley; M. Bouchon, N. Orbovic and B. Foure; T. Gelain, F. Gensdarmes, R. Sestier-Carlin, J. Vendel and M. Bouchon dealing respectively with: 1) seismic assessment of existing nuclear facility: a case study position of the IRSN 2) static and dynamic evaluation of an existing nuclear facility reinforced concrete frame structure 3) experimental study of cracking of low-rise reinforced concrete shear walls 4) aeraulics study of crack networks on low-rise reinforced concrete walls subject to static cycling loading. The summaries are followed: 1) The Institute for Radioprotection and Nuclear Safety (IRSN) has the task of evaluating the seismic safety of existing building inventory in French nuclear facilities. Some of the existing structures are reinforced concrete frame buildings with masonry or reinforced concrete in-fill walls built during the 1960's, 70's and 80's following different building codes and seismic input data applicable at the time of construction. The studied building is a laboratory that was built in 1962. The building is composed of three different and independent blocks. The structure is a reinforced concrete frame with masonry in-fills and few stiff concrete elements. Moreover, the building contains an independent massive concrete cell. Structurally, the building has a number of irregularities. From the detailing standpoint, well known deficiencies of low-ductile reinforced concrete structures are evident especially, a lack of transverse reinforcement in the structural joints of the frame. A number of sensitivity studies were conducted using 2D and 3D linear models to evaluate seismic demand. Ambient vibration and regional earthquake records were used to check the soil nature and the existence or not of a possible site effect around the installation as well as to characterize the dynamic behavior of the building. 3D models revealed a

  4. 78 FR 52903 - Notice of Petitions by Firms for Determination of Eligibility To Apply for Trade Adjustment...

    Science.gov (United States)

    2013-08-27

    ... produced by each of these firms contributed importantly to the total or partial separation of the firm's... breakaway couplings for pumps that dispense and measure gasoline. Humphrey Products Company 5070 East N Ave...

  5. The Transient Intermediate Plexiform Layer, a Plexiform Layer-like Structure Temporarily Existing in the Inner Nuclear Layer in Developing Rat Retina.

    Science.gov (United States)

    Park, Hyung Wook; Kim, Hong-Lim; Park, Yong Soo; Kim, In-Beom

    2018-02-01

    The retina is a highly specialised part of the brain responsible for visual processing. It is well-laminated; three layers containing five different types of neurons are compartmentalised by two synaptic layers. Among the retinal layers, the inner nuclear layer (INL) is composed of horizontal, bipolar, and amacrine cell types. Bipolar cells form one sublayer in the distal half of the IPL, while amacrine cells form another sublayer in the proximal half, without any border-like structure. Here, we report that a plexiform layer-like structure exists temporarily in the border between the bipolar and amacrine sublayers in the INL in the rat retina during retinal development. This transient intermediate plexiform layer (TIPL) appeared at postnatal day (PD) 7 and then disappeared around PD 12. Most apoptotic cells in the INL were found near the TIPL. These results suggest that the TIPL may contribute to the formation of sublayers and the cell number limit in the INL.

  6. Research into zirconium alloys resistant to carbon dioxide under pressure at temperatures of up to 600 deg C (1963); Recherche d'alliages de zirconium compatibles avec le gaz carbonique sous pression jusqu'a 500 ou 600 deg C (1063)

    Energy Technology Data Exchange (ETDEWEB)

    Baque, P; Dominget, R; Bossard, J [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1963-07-01

    Zirconium is a metal having a relatively low neutron capture cross-section and a high melting point; it is thus possible to consider its use in particular as a canning material for fuel elements in CO{sub 2}-cooled nuclear reactors. A preliminary study of several types of zirconium showed that the metal is already strongly oxidised in this gas at 500 deg C. The 'breakaway' phenomenon is generalised; the oxidation rate is then linear and depends on the carbon dioxide pressure. An attempt was therefore made to find binary and tertiary alloys in order to improve the metal behaviour. Several interesting compositions were found: 1, 1.6 and 2.5 per cent of copper, 2 per cent of vanadium, and 0.05 and 0.5 per cent of calcium. Tertiary copper-molybdenum and copper-phosphorus alloys are also less liable to oxidation and in particular do not exhibit the 'breakaway' phenomenon even after a prolonged treatment at 600 deg C. (authors) [French] Le zirconium se trouve parmi les metaux a section de capture neutronique relativement faible et possede une temperature de fusion elevee; aussi peut on songer a l'employer notamment comme materiau de gainage d'elements combustibles pour reacteurs nucleaires refroidis au gaz carbonique. Une etude prealable de plusieurs qualites de zirconium a montre que le metal est deja assez fortement oxyde dans ce gaz des 500 deg C. En effet, le phenomene de ''breakaway'' est general; la vitesse d'oxydation devient alors lineaire et depend de la pression du gaz carbonique. La recherche d'alliages binaires et ternaires a donc ete entreprise afin de tenter d'ameliorer le comportement du metal. Elle a permis d'aboutir a quelques compositions interessantes: cuivre 1, 1,6 et 2,5 pour cent, vanadium 2 pour cent, et calcium 0,05 et 0,5 pour cent. Des alliages ternaires au cuivre-molybdene et cuivre-phosphore sont egalement moins oxydables, et en particulier ne presentent pas le phenomene de ''breakaway'', meme apres une longue exposition a 600 deg C. (auteurs)

  7. Computer aided seismic and fire retrofitting analysis of existing high rise reinforced concrete buildings

    CERN Document Server

    Hussain, Raja Rizwan; Hasan, Saeed

    2016-01-01

    This book details the analysis and design of high rise buildings for gravity and seismic analysis. It provides the knowledge structural engineers need to retrofit existing structures in order to meet safety requirements and better prevent potential damage from such disasters as earthquakes and fires. Coverage includes actual case studies of existing buildings, reviews of current knowledge for damages and their mitigation, protective design technologies, and analytical and computational techniques. This monograph also provides an experimental investigation on the properties of fiber reinforced concrete that consists of natural fibres like coconut coir and also steel fibres that are used for comparison in both Normal Strength Concrete (NSC) and High Strength Concrete (HSC). In addition, the authors examine the use of various repair techniques for damaged high rise buildings. The book will help upcoming structural design engineers learn the computer aided analysis and design of real existing high rise buildings ...

  8. The Chechen War: Another Russian Humiliation

    National Research Council Canada - National Science Library

    Perrin

    2001-01-01

    ...." Thus began the Chechen War in December 1994, sparked by an out-of-control, breakaway republic and fueled by the Kremlin's need to maintain integrity of the Russian Federation and to control strategic resources...

  9. Assessment of wind turbine seismic risk : existing literature and simple study of tower moment demand.

    Energy Technology Data Exchange (ETDEWEB)

    Prowell, Ian (University of California, San Diego, CA); Veers, Paul S.

    2009-03-01

    Various sources of risk exist for all civil structures, one of which is seismic risk. As structures change in scale, the magnitude of seismic risk changes relative to risk from other sources. This paper presents an introduction to seismic hazard as applied to wind turbine structures. The existing design methods and research regarding seismic risk for wind turbines is then summarized. Finally a preliminary assessment is made based on current guidelines to understand how tower moment demand scales as rated power increases. Potential areas of uncertainty in the application of the current guidelines are summarized.

  10. Subtle trade-off existing between (anti)aromaticity, push-pull interaction, keto-enol tautomerism, and steric hindrance when defining the electronic properties of conjugated structures.

    Science.gov (United States)

    Kleinpeter, Erich; Bölke, Ute; Koch, Andreas

    2010-07-22

    The spatial magnetic properties (through space NMR shieldings, TSNMRS) of conjugated structures (benzenoid/quinonoid keto/enol tautomers, 1,3-dihydroxyaryl-2-aldehydes, Don-pi-Acc chromophores with trade-off existing push-pull vs aromatic behavior) have been calculated by the GIAO perturbation method employing the nucleus independent chemical shift (NICS) concept, and visualized as iso-chemical-shielding surfaces (ICSS) of various size and direction. The TSNMRS values, thus obtained, can be successfully employed to quantify and visualize (anti)aromaticity and to identify readily hereby zwitterionic structures due to push-pull behavior of the compounds studied. In addition, the push-pull behavior was quantified by the quotient (pi*/pi) approach of the central partial C=C double bond.

  11. Oxidation behavior of U-Si compounds in air from 25 to 1000 C

    Energy Technology Data Exchange (ETDEWEB)

    Sooby Wood, E., E-mail: sooby@lanl.gov; White, J.T.; Nelson, A.T.

    2017-02-15

    The air oxidation behavior of U{sub 3}Si{sub 2}, USi, and U{sub 3}Si{sub 5} is studied from room temperature to 1000 C. The onsets of breakaway oxidation for each compound are identified during synthetic air ramps to 1000 C using thermogravimetric analysis. Isothermal air oxidation tests are performed below and above the breakaway oxidation onset to discern the oxidation kinetic behavior of these candidate accident tolerant fuel forms. Uranium metal is tested in the same manner to provide a reference for the oxidation behavior. Thermogravimetric, x-ray diffraction, and scanning electron microscopy analysis are presented here along with a discussion of the oxidation behavior of these materials and the impact of the lack of oxidation resistance to their deployment as accident tolerant nuclear fuels.

  12. Co-existence of Gel and Fluid Lipid Domains in Single-component Phospholipid Membranes

    Energy Technology Data Exchange (ETDEWEB)

    Armstrong, Clare L [McMaster University; Barrett, M [McMaster University; Toppozini, L [McMaster University; Yamani, Zahra [Canadian Neutron Beam Centre, National Research Council, Chalk River Laboratorie; Kucerka, Norbert [Canadian Neutron Beam Centre and Comelius University (Slovakia); Katsaras, John [ORNL; Fragneto, Giovanna [Institut Laue-Langevin (ILL); Rheinstadter, Maikel C [McMaster University

    2012-01-01

    Lateral nanostructures in membranes, so-called rafts, are believed to strongly influence membrane properties and functions. The experimental observation of rafts has proven difficult as they are thought to be dynamic structures that likely fluctuate on nano- to microsecond time scales. Using neutron diffraction we present direct experimental evidence for the co-existence of gel and fluid lipid domains in a single-component phospholipid membrane made of DPPC as it undergoes its main phase transition. The coherence length of the neutron beam sets a lower limit for the size of structures that can be observed. Neutron coherence lengths between 30 and 242A used in this study were obtained by varying the incident neutron energy and the resolution of the neutron spectrometer. We observe Bragg peaks corresponding to co-existing nanometer sized structures, both in out-of-plane and in-plane scans, by tuning the neutron coherence length. During the main phase transition, instead of a continuous transition that shows a pseudo-critical behavior, we observe the co-existence of gel and fluid domains.

  13. Plaadid / Mart Normet

    Index Scriptorium Estoniae

    Normet, Mart, 1979-

    2005-01-01

    Uute heliplaatide Depeche Mode "Playing The Angel", King, B. B. "80", Ray Charles"Genius & Friends", /Queen, PaulRodgers "Return Of The Champions", Sugababes "Taller in More Ways", Kelly Clarkson ""Breakaway, Mike Oldfield "Light and Shade"

  14. Elastic scattering of helium ions on 9Be nuclei and exchange mechanisms

    International Nuclear Information System (INIS)

    Burtebaev, N.; Dujsebaev, B.A.

    1999-01-01

    Among nuclei of 1p-shell 9 Be is an extremely deformed nucleus with cluster structure. This considerably impedes determination of nucleus-nucleus potential of interaction. The latter relates to the fact that cross-section of 3 He ion and ?-particle elastic scattering on light nuclei is formed by not only mechanism of mere potential nature but also by other processes of heavy breakaway and displacement as well as by effects of channel relation. Final probability of 6 He+ and 3 He and 5 He+? cluster existence in 9 Be nucleus can be determined in the processes of 3 He or ?-particle ion scattering. As a result, it can cause considerable growth of cross-section under backward angles due to exchange of impinging particle with identical cluster in a nucleus. In order to study the contribution of different mechanisms into formation of cross-section of elastic scattering of helium nuclides on 9 Be nucleus we have performed series of experiments in broad angular range at energies 8-20 MeV/nucleon at derived beams of isochronous cyclotron of the Institute of Nuclear Physics of Kazakhstan national Nuclear Centre

  15. Evaluation of Existing Structures

    Science.gov (United States)

    1974-12-01

    13520 500 G0T0C530.S20*530*5*0). JENTRY 13S30C 135440C INPUT LOAD DATA 133S50 510 PRINT 68(P 13560 READDNPOINT.(TT(J) bPP (J).JO1DNPOINT) 13570 FACTOR*1.O...T’)IST(CCI’d0E4,5)𔃿) 710p0 ?J.A41-ý4E5T04eS"RTDIST TCl’J0)E-1b)/5) 71 0:0 Snl=S/l(S0Sf)T( CH 4 75( C 1 I0Ex- 15 /5)) 71040 Pl0-t~ fFA ’-1.2q32*SD 710

  16. Does pop music exist? Hierarchical structure in phonographic markets

    Science.gov (United States)

    Buda, Andrzej

    2012-11-01

    I find a topological arrangement of assets traded in phonographic markets which has associated a meaningful economic taxonomy. I continue using the Minimal Spanning Tree and the correlations between assets, but now outside the stock markets. This is the first attempt to use these methods on phonographic markets where we have artists instead of stocks. The value of an artist is defined by record sales. The graph is obtained starting from the matrix of correlation coefficients computed between the world’s most popular 30 artists by considering the synchronous time evolution of the difference of the logarithm of weekly record sales. This method provides the hierarchical structure of the phonographic market and information on which music genre is meaningful according to customers. Statistical properties (including the Hurst exponent) of weekly record sales in the phonographic market are also discussed.

  17. Role of pre-existing structures in controlling the Cenozoic tectonic evolution of the eastern Tibetan plateau: New insights from analogue experiments

    Science.gov (United States)

    Sun, Ming; Yin, An; Yan, Danping; Ren, Hongyu; Mu, Hongxu; Zhu, Lutao; Qiu, Liang

    2018-06-01

    Pre-existing weakness due to repeated tectonic, metamorphic, and magmatic events is a fundamental feature of the continental lithosphere on Earth. Because of this, continental deformation results from a combined effect of boundary conditions imposed by plate tectonic processes and heterogeneous and anisotropic mechanical strength inherited from protracted continental evolution. In this study, we assess how this interaction may have controlled the Cenozoic evolution of the eastern Tibetan plateau during the India-Asia collision. Specifically, we use analogue models to evaluate how the pre-Cenozoic structures may have controlled the location, orientation, and kinematics of the northwest-striking Xianshuihe and northeast-striking Longmen Shan fault zones, the two most dominant Cenozoic structures in eastern Tibet. Our best model indicates that the correct location, trend, and kinematics of the two fault systems can only be generated and maintained if the following conditions are met: (1) the northern part of the Songpan-Ganzi terrane in eastern Tibet has a strong basement whereas its southern part has a weak basement, (2) the northern strong basement consists of two pieces bounded by a crustal-scale weak zone that is expressed by the Triassic development of a northwest-trending antiform exposing middle and lower crustal rocks, and (3) the region was under persistent northeast-southwest compression since ∼35 Ma. Our model makes correct prediction on the sequence of deformation in eastern Tibet; the Longmen Shan right-slip transpressional zone was initiated first as an instantaneous response to the northeast-southwest compression, which is followed by the formation of the Xianshuihe fault about a half way after the exertion of northeast-southwest shortening in the model. The success of our model highlights the importance of pre-existing weakness, a key factor that has been largely neglected in the current geodynamic models of continental deformation.

  18. Atomistic simulations of the formation of -component dislocation loops in α-zirconium

    Energy Technology Data Exchange (ETDEWEB)

    Dai, Cong, E-mail: dai.cong@queensu.ca; Balogh, Levente; Yao, Zhongwen; Daymond, Mark R., E-mail: mark.daymond@queensu.ca

    2016-09-15

    The formation of -component dislocation loops in α-Zr is believed to be responsible for the breakaway irradiation growth experimentally observed under high irradiation fluences. However, while -loop growth is well described by existing models, the atomic mechanisms responsible for the nucleation of -component dislocation loops are still not clear. In the present work, both interstitial and vacancy -type dislocation loops are initially equilibrated at different temperatures. Cascades simulations in the vicinity of the -type loops are then performed by selecting an atom as the primary knock-on atoms (PKAs) with different kinetic energies, using molecular dynamics simulations. No -component dislocation loop was formed in cascades simulations with a 10 keV PKA, but -component interstitial loops were observed after the interaction between discontinuous 50 keV PKAs and pre-existing -type interstitial loops. The comparisons of cascades simulations in volumes having pre-existing -type interstitial and vacancy loops suggest that the reaction between the PKAs and -type interstitial loops is responsible for the formation of -component interstitial loops.

  19. Methodology for safety evaluation of existing timber elements

    OpenAIRE

    Sousa, Hélder S.

    2013-01-01

    Tese de doutoramento em Engenharia Civil The past decades have seen a renewed interest in timber research related topics. As instance, timber engineering is not only confined to the design of new construction with innovative wood based products, but also an increasing awareness for the preservation of existing timber structures is visible in nowadays society. Therefore, arises the need for a better understanding of timber performance as a construction material aiming at a bette...

  20. AGR steel corrosion monitoring schemes: progress on off-site testing of coupon specimens to end of 1985: Pt. 1

    International Nuclear Information System (INIS)

    Whittle, I.; Meredith, M.E.

    1988-03-01

    Off-site Advanced Gas-cooled Reactor steel corrosion monitoring through experiments on mild steel coupon specimens is reported. The appearance of all mild steel coupons oxidised over the temperature range 375 to 450 0 C is consistent with what is expected for the appropriate silicon content, temperature and in the gas mixes used. Likewise, weight gain data from the tests is as expected and where linear (breakaway) oxidation kinetics are in evidence, measured rates are within one standard deviation of the mean oxidation rates predicted by the 1/R model. Also, data relating mean breakaway oxide thickness to weight gain is in good agreement with the currently recommended relationship of 1 mg cm -2 weight gain = 6.72 μm oxide thickness. The observed oxidation behaviour of the off-site mild steel coupons is consistent with the most recent design data. (author)

  1. Gamma Ray Bursts as Cosmological Probes with EXIST

    Science.gov (United States)

    Hartmann, Dieter; EXIST Team

    2006-12-01

    The EXIST mission, studied as a Black Hole Finder Probe within NASA's Beyond Einstein Program, would, in its current design, trigger on 1000 Gamma Ray Bursts (GRBs) per year (Grindlay et al, this meeting). The redshift distribution of these GRBs, using results from Swift as a guide, would probe the z > 7 epoch at an event rate of > 50 per year. These bursts trace early cosmic star formation history, point to a first generation of stellar objects that reionize the universe, and provide bright beacons for absorption line studies with groundand space-based observatories. We discuss how EXIST, in conjunction with other space missions and future large survey programs such as LSST, can be utilized to advance our understanding of cosmic chemical evolution, the structure and evolution of the baryonic cosmic web, and the formation of stars in low metallicity environments.

  2. Conformal Haag-Kastler nets, pointlike localized fields and the existence of operator product expansions

    International Nuclear Information System (INIS)

    Fredenhagen, K.; Joerss, M.

    1994-10-01

    Starting from a chiral conformal Haag-Kastler net on 2 dimensional Minkowski space we construct associated pointlike localized fields. This amounts to a proof of the existence of operator product expansions. We derive the result in two ways. One is based on the geometrical identification of the modular structure, the other depends on a ''conformal cluster theorem'' of the conformal two-point-functions in algebraic quantum field theory. The existence of the fields then implies important structural properties of the theory, as PCT-invariance, the Bisognano-Wichmann identification of modular operators, Haag duality and additivity. (orig.)

  3. Deployment Surveillance Summary, U.S. Army Operation Iraqi Freedom/Operation New Dawn/Operation Enduring Freedom, 2011. Injury Prevention Report

    Science.gov (United States)

    2012-12-10

    d) Breakaway bases, recessed bases, and proper sliding technique education for softball and baseball sliding injuries.(31) (e...327. 31. Pollack K, Canham-Chervak M, Gazal-Carvalho C, Jones B, Baker S. 2005. Interventions to prevent softball related injuries: a review

  4. Safety barriers and lighting columns.

    NARCIS (Netherlands)

    Schreuder, D.A.

    1972-01-01

    Problems arising from the sitting of lighting columns on the central reserve are reviewed, and remedial measures such as break-away lighting supports and installation of safety fences on the central reserve on both sides of the lighting columns are examined.

  5. Oxidation behavior of TiC particle-reinforced 304 stainless steel

    International Nuclear Information System (INIS)

    Wu Qianlin; Zhang Jianqiang; Sun Yangshan

    2010-01-01

    TiC particle-reinforced 304 stainless steels were prepared using a new developed in situ technology and exhibited the uniform distribution of TiC particles in the matrix. The oxidation behavior of 304SS-2TiC and 304SS-6TiC (all in weight percentage) was compared with that of 304SS at 850 deg. C in air for 96 h using thermogravimetry analysis. For 304SS, the rate of weight gain was very slow initially, but accelerated suddenly to a very high level, forming breakaway oxidation. The addition of TiC particles to 304SS resulted in no breakaway oxidation and maintained a low oxidation rate in the whole reaction time investigated. Examination of oxide scale morphology and cross-section analysis by scanning electron microscopy and optical microscopy showed a significant scale spallation and a deep oxide penetration in the case of 304SS, but a rather continuous, dense and adherent oxide layer formed on the surface of TiC particle-reinforced alloys. XRD analysis revealed the presence of Cr 2 O 3 together with spinel-type oxides in the oxide scale. For TiC-containing alloys, fine TiO 2 was also found on the surface and the amount of this oxide increased with TiC addition. The TiC addition developed finer matrix structure before oxidation, which accelerates chromium diffusion. As a result, scale adherence was improved and oxidation resistance was increased.

  6. The Structure of Artefacts of Management Control in the Innovation Process: Does Exist Association with the Strategic Profile?

    Directory of Open Access Journals (Sweden)

    Fábio Frezatti

    2015-01-01

    Full Text Available This study investigates what is the role of strateg ic profiles and management control instruments in organisations’ innovation process. B ased in a survey using structural equation modelling (121 companies, we confirm that analyser , defender e prospector profiles are associated with strategic planning, balanced scorec ard (BSC and rolling forecast. The reactor type is associated with lower use of artefacts. Our results confirm the linkage between incremental innovation and strategic planning and b etween radical innovation and BSC. These findings reflect the alignment between strate gic types, the availability of instruments and intensity of innovation, which is useful inform ation with which to understand organisations and their market activities. This pap er bring information about specific management control instruments existence and the im pact for the intensity of the innovation that is relevant for management and must stimulate organizations to be consistent in the cases that the strategic profile is a clear long term def inition or see the possibility of change when it is not the desired one.

  7. The existence of a stable noncollinear phase in a Heisenberg model with complex structure

    Energy Technology Data Exchange (ETDEWEB)

    Shopova, Diana V.; Boyadjiev, Todor L

    2003-05-19

    We have analyzed the properties of a noncollinear magnetic phase obtained in the mean-field analysis of the model of two coupled Heisenberg subsystems. The domain of its existence and stability is narrow and depends on the ratio between the averaged over nearest neighbours microscopic exchange parameters.

  8. Inter professionalization and the breakaway from classic concepts

    DEFF Research Database (Denmark)

    Borgnakke, Karen; Nielsen, Cathrine Sand

    2014-01-01

    to explore and describe how the perspective of InBetween can help to strengthen and develop the individual, inter-professional and (inter)organisational learning generating new knowledge of: - the contributions of InBetween to the quality of future health professional education and to the future healthcare...

  9. Reversible unfolding of infectious prion assemblies reveals the existence of an oligomeric elementary brick.

    Directory of Open Access Journals (Sweden)

    Angélique Igel-Egalon

    2017-09-01

    Full Text Available Mammalian prions, the pathogens that cause transmissible spongiform encephalopathies, propagate by self-perpetuating the structural information stored in the abnormally folded, aggregated conformer (PrPSc of the host-encoded prion protein (PrPC. To date, no structural model related to prion assembly organization satisfactorily describes how strain-specified structural information is encoded and by which mechanism this information is transferred to PrPC. To achieve progress on this issue, we correlated the PrPSc quaternary structural transition from three distinct prion strains during unfolding and refolding with their templating activity. We reveal the existence of a mesoscopic organization in PrPSc through the packing of a highly stable oligomeric elementary subunit (suPrP, in which the strain structural determinant (SSD is encoded. Once kinetically trapped, this elementary subunit reversibly loses all replicative information. We demonstrate that acquisition of the templating interface and infectivity requires structural rearrangement of suPrP, in concert with its condensation. The existence of such an elementary brick scales down the SSD support to a small oligomer and provide a basis of reflexion for prion templating process and propagation.

  10. Seismic evaluation of existing nuclear facilities. Proceedings

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-07-01

    Programmes for re-evaluation and upgrading of safety of existing nuclear facilities are presently under way in a number of countries around the world. An important component of these programmes is the re-evaluation of the seismic safety through definition of new seismic parameters at the site and evaluation of seismic capacity of structures, equipment and distribution systems following updated information and criteria. The Seminar is intended to provide a forum for the exchange of information and discussion of the state-of-the-art on seismic safety of nuclear facilities in operation or under construction. Both analytical and experimental techniques for the evaluation of seismic capacity of structures, equipment and distribution systems are discussed. Full scale and field tests of structures and components using shaking tables, mechanical exciters, explosive and shock tests, and ambient vibrations are included in the seminar programme with emphasis on recent case histories. Presentations at the Seminar also include analytical techniques for the determination of dynamic properties of soil-structure systems from experiments as well as calibration of numerical models. Methods and criteria for seismic margin assessment based on experience data obtained from the behaviour of structures and components in real earthquakes are discussed. Guidelines for defining technical requirements for capacity re-evaluation (i.e. acceptable behaviour limits and design and implementation of structure and components upgrades are also presented and discussed. The following topics were covered during 7 sessions: earthquake experience and seismic re-evaluation; country experience in seismic re-evaluation programme; generic WWER studies; analytical methods for seismic capacity re-evaluation; experimental methods for seismic capacity re-evaluation; case studies.

  11. Seismic evaluation of existing nuclear facilities. Proceedings

    International Nuclear Information System (INIS)

    1995-01-01

    Programmes for re-evaluation and upgrading of safety of existing nuclear facilities are presently under way in a number of countries around the world. An important component of these programmes is the re-evaluation of the seismic safety through definition of new seismic parameters at the site and evaluation of seismic capacity of structures, equipment and distribution systems following updated information and criteria. The Seminar is intended to provide a forum for the exchange of information and discussion of the state-of-the-art on seismic safety of nuclear facilities in operation or under construction. Both analytical and experimental techniques for the evaluation of seismic capacity of structures, equipment and distribution systems are discussed. Full scale and field tests of structures and components using shaking tables, mechanical exciters, explosive and shock tests, and ambient vibrations are included in the seminar programme with emphasis on recent case histories. Presentations at the Seminar also include analytical techniques for the determination of dynamic properties of soil-structure systems from experiments as well as calibration of numerical models. Methods and criteria for seismic margin assessment based on experience data obtained from the behaviour of structures and components in real earthquakes are discussed. Guidelines for defining technical requirements for capacity re-evaluation (i.e. acceptable behaviour limits and design and implementation of structure and components upgrades are also presented and discussed. The following topics were covered during 7 sessions: earthquake experience and seismic re-evaluation; country experience in seismic re-evaluation programme; generic WWER studies; analytical methods for seismic capacity re-evaluation; experimental methods for seismic capacity re-evaluation; case studies

  12. Eternally existing self-reproducing inflationary universe

    International Nuclear Information System (INIS)

    Linde, A.D.

    1986-05-01

    It is shown that the large-scale quantum fluctuations of the scalar field φ generated in the chaotic inflation scenario lead to an infinite process of self-reproduction of inflationary mini-universes. A model of eternally existing chaotic inflationary universe is suggested. It is pointed out that whereas the universe locally is very homogeneous as a result of inflation, which occurs at the classical level, the global structure of the universe is determined by quantum effects and is highly non-trivial. The universe consists of exponentially large number of different mini-universes, inside which all possible (metastable) vacuum states and all possible types of compactification are realized. The picture differs crucially from the standard picture of a one-domain universe in a ''true'' vacuum state. Our results may serve as a justification of the anthropic principle in the inflationary cosmology. These results may have important implications for the elementary particle theory as well. Namely, since all possible types of mini-universes, in which inflation may occur, should exist in our universe, there is no need to insist (as it is usually done) that in realistic theories the vacuum state of our type should be the only possible one or the best one. (author)

  13. EXIST Perspective for SFXTs

    Science.gov (United States)

    Ubertini, Pietro; Sidoli, L.; Sguera, V.; Bazzano, A.

    2009-12-01

    Supergiant Fast X-ray Transients (SFXTs) are one of the most interesting (and unexpected) results of the INTEGRAL mission. They are a new class of HMXBs displaying short hard X-ray outbursts (duration less tha a day) characterized by fast flares (few hours timescale) and large dinamic range (10E3-10E4). The physical mechanism driving their peculiar behaviour is still unclear and highly debated: some models involve the structure of the supergiant companion donor wind (likely clumpy, in a spherical or non spherical geometry) and the orbital properties (wide separation with eccentric or circular orbit), while others involve the properties of the neutron star compact object and invoke very low magnetic field values (B 1E14 G, magnetars). The picture is still highly unclear from the observational point of view as well: no cyclotron lines have been detected in the spectra, thus the strength of the neutron star magnetic field is unknown. Orbital periods have been measured in only 4 systems, spanning from 3.3 days to 165 days. Even the duty cycle seems to be quite different from source to source. The Energetic X-ray Imaging Survey Telescope (EXIST), with its hard X-ray all-sky survey and large improved limiting sensitivity, will allow us to get a clearer picture of SFXTs. A complete census of their number is essential to enlarge the sample. A long term and continuous as possible X-ray monitoring is crucial to -(1) obtain the duty cycle, -(2 )investigate their unknown orbital properties (separation, orbital period, eccentricity),- (3) to completely cover the whole outburst activity, (4)-to search for cyclotron lines in the high energy spectra. EXIST observations will provide crucial informations to test the different models and shed light on the peculiar behaviour of SFXTs.

  14. Existence of solution for a general fractional advection-dispersion equation

    Science.gov (United States)

    Torres Ledesma, César E.

    2018-05-01

    In this work, we consider the existence of solution to the following fractional advection-dispersion equation -d/dt ( p {_{-∞}}It^{β }(u'(t)) + q {t}I_{∞}^{β }(u'(t))) + b(t)u = f(t, u(t)),t\\in R where β \\in (0,1) , _{-∞}It^{β } and tI_{∞}^{β } denote left and right Liouville-Weyl fractional integrals of order β respectively, 0continuous functions. Due to the general assumption on the constant p and q, the problem (0.1) does not have a variational structure. Despite that, here we study it performing variational methods, combining with an iterative technique, and give an existence criteria of solution for the problem (0.1) under suitable assumptions.

  15. New And Existing Bridge Constructions - Increase of Fatigue Strength of Welded Joints by High Frequency Mechanical Impact Treatment

    Directory of Open Access Journals (Sweden)

    Ummenhofer Thomas

    2013-07-01

    Full Text Available Numerous studies at KIT prove that high frequency mechanical impact (HFMI treatment is an efficient method for increasing the fatigue strength of welded steel structures. Within different research projects it was found that HFMI-methods can be used successfully for new and existing structures in order to extend the fatigue life. This paper gives an overview of the current status of existing steel bridges in Germany regarding aspects like bridge age distributions and traffic loads. Based on that overview welded joints susceptible to fatigue failure are identified. Using component-like small scale specimens, HFMI-methods were investigated within the objective of implementing an effective application for new and existing structures. Applying the fatigue test data observed, existing design proposals are evaluated and design recommendations for HFMI-treated joints are given. As a result of the research work, a transfer into practice has been realized and different applications are illustrated using the example of bridge constructions made of steel.

  16. Global Existence Results for Viscoplasticity at Finite Strain

    Science.gov (United States)

    Mielke, Alexander; Rossi, Riccarda; Savaré, Giuseppe

    2018-01-01

    We study a model for rate-dependent gradient plasticity at finite strain based on the multiplicative decomposition of the strain tensor, and investigate the existence of global-in-time solutions to the related PDE system. We reveal its underlying structure as a generalized gradient system, where the driving energy functional is highly nonconvex and features the geometric nonlinearities related to finite-strain elasticity as well as the multiplicative decomposition of finite-strain plasticity. Moreover, the dissipation potential depends on the left-invariant plastic rate, and thus depends on the plastic state variable. The existence theory is developed for a class of abstract, nonsmooth, and nonconvex gradient systems, for which we introduce suitable notions of solutions, namely energy-dissipation-balance and energy-dissipation-inequality solutions. Hence, we resort to the toolbox of the direct method of the calculus of variations to check that the specific energy and dissipation functionals for our viscoplastic models comply with the conditions of the general theory.

  17. Existing reflection seismic data re-processing

    International Nuclear Information System (INIS)

    Higashinaka, Motonori; Sano, Yukiko; Kozawa, Takeshi

    2005-08-01

    This document is to report the results of existing seismic data re-processing around Horonobe town, Hokkaido, Japan, which is a part of the Horonobe Underground Research Project. The main purpose of this re-processing is to recognize the subsurface structure of Omagari Fault and fold system around Omagari Fault. The seismic lines for re-processing are TYHR-A3 line and SHRB-2 line, which JAPEX surveyed in 1975. Applying weathering static correction using refraction analysis and noise suppression procedure, we have much enhanced seismic profile. Following information was obtained from seismic re-processing results. TYHR-A3 line: There are strong reflections, dipping to the west. These reflections are corresponding western limb of anticline to the west side of Omagari Fault. SHRB-2 line: There are strong reflections, dipping to the west, at CDP 60-140, while there are reflections, dipping to the east, to the east side of CDP 140. These reflections correspond to the western limb and the eastern limb of the anticline, which is parallel to Omagari FAULT. This seismic re-processing provides some useful information to know the geological structure around Omagari Fault. (author)

  18. Existence conditions for bulk large-wavevector waves in metal-dielectric and graphene-dielectric multilayer hyperbolic metamaterials

    DEFF Research Database (Denmark)

    Zhukovsky, Sergei; Andryieuski, Andrei; Lavrinenko, Andrei

    2014-01-01

    We theoretically investigate general existence conditions for broadband bulk large-wavevector (high-k) propagating waves (such as volume plasmon polaritons in hyperbolic metamaterials) in arbitrary subwavelength periodic multilayers structures. Treating the elementary excitation in the unit cell...... of the structure as a generalized resonance pole of reflection coefficient and using Bloch's theorem, we derive analytical expressions for the band of large-wavevector propagating solutions. We apply our formalism to determine the high-k band existence in two important cases: the well-known metal-dielectric...

  19. Greening Existing Tribal Buildings

    Science.gov (United States)

    Guidance about improving sustainability in existing tribal casinos and manufactured homes. Many steps can be taken to make existing buildings greener and healthier. They may also reduce utility and medical costs.

  20. U. S. Army Operation Enduring Freedom Deployment Injury Surveillance Summary, 1 January-31 December 2012

    Science.gov (United States)

    2015-06-01

    30).  Breakaway bases, recessed bases, and proper sliding technique education for softball and baseball sliding injuries (reference 31... softball related injuries: a review of the literature. Inj Prev 11(5):277-281. 32. Knapik JJ, Marshall SW, Lee RB, Darakjy SS, Jones SB

  1. Requirements for existing buildings

    DEFF Research Database (Denmark)

    Thomsen, Kirsten Engelund; Wittchen, Kim Bjarne

    This report collects energy performance requirements for existing buildings in European member states by June 2012.......This report collects energy performance requirements for existing buildings in European member states by June 2012....

  2. Risk management for existing energy facilities. A global approach to numerical safety goals

    International Nuclear Information System (INIS)

    Pate-Cornell, M.E.

    1993-01-01

    This paper presents a structured set of numerical safety goals for risk management of existing energy facilities. The rationale behind these safety goals is based on principles of equity and economic efficiency. Some of the issues involved when using probabilistic risk analyses results for safety decisions are discussed. A brief review of existing safety targets and open-quotes floating numbersclose quotes is presented, and a set of safety goals for industrial risk management is proposed. Relaxation of these standards for existing facilities, the relevance of the lifetime of the plant, the treatment of uncertainties, and problems of failure dependencies are discussed briefly. 17 refs., 1 fig

  3. Electrochemical lithium migration to mitigate alkali-silica reaction in existing concrete structures

    NARCIS (Netherlands)

    Silva De Souza, L.M.

    2016-01-01

    Alkali-silica reaction (ASR) is a deterioration process that affects the durability of concrete structures worldwide. During the reaction, hydroxyl and alkali ions present in the pore solution react with reactive silica from the aggregate, forming a hygroscopic ASR gel. Alternatively, the silica

  4. Consideration of higher seismic loads at existing plants

    Energy Technology Data Exchange (ETDEWEB)

    Liebig, J.; Pellissetti, M.

    2015-07-01

    Because of advancement of methods in probabilistic seismic hazard analysis, plenty of existing plants face higher seismic loads as an obligation from the national authorities. In case of such obligations safety related structures and equipment have to be reevaluated or requalified for the increased seismic loads. The paper provides solutions for different kinds of structures and equipment inside the plant, avoiding cost intensive hardware exchange. Due to higher seismic loads different kinds of structures and equipment inside a plant have to be reevaluated. For civil structures, primary components, mechanical components, distribution lines and electrical and I&C equipment different innovative concepts will be applied to keep structures and equipment qualified for the higher seismic loads. Detailed analysis, including the modeling of non-linear phenomena, or minor structural upgrades are cost competitive, compared to cost intensive hardware exchanges. Several case studies regarding the re-evaluation and requalification of structures and equipment due to higher seismic loads are presented. It is shown how the creation of coupled finite element models and the consistent propagation of acceleration time histories through the soil, building and primary circuit lead to a significant load reduction Electrical and I&C equipment is reinforced by smart upgrades which increase the natural equipment frequencies. Therefore for all devices inside the cabinets the local acceleration will not increase and the seismic qualification will be maintained. The case studies cover both classical deterministic and probabilistic re-evaluations (fragility analysis). Furthermore, the substantial benefits of non-linear limit load evaluation, such as push-over analysis of buildings and limit load analysis of fuel assemblies, are demonstrated. (Author)

  5. Structural evaluations of existing underground reinforced concrete tanks for radioactive waste storage

    International Nuclear Information System (INIS)

    Vollert, F.R.

    1979-10-01

    Structural integrity evaluations are being conducted for underground, steel-lined reinforced concrete tanks for storing radioactive wastes. The tanks sustain large soil overburden loads and elevated temperatures from the waste for long time periods. The evaluations include laboratory experiments to determine the long-term effects of elevated temperatures on the elastic properties of concrete, and to estimate the effect of the waste chemicals on concrete durability. Available concrete samples from the tanks were also tested to determine the quality of the concrete in the tanks and for comparison with the laboratory data. Finite element, nonlinear, time-dependent analyses are performed to show the thermal creep, cracking, and stresses occurring in the concrete tanks due to the service conditions. Ultimate load analyses are made to assess the safety margin in the tanks. Finally, seismic analyses of a tank in the stressed condition due to the soil and thermal loadings were conducted to determine that the structure has sufficient reserve capacity to withstand 0.25 g earthquake accelerations

  6. Chimera States in Continuous Media: Existence and Distinctness

    Science.gov (United States)

    Nicolaou, Zachary G.; Riecke, Hermann; Motter, Adilson E.

    2017-12-01

    The defining property of chimera states is the coexistence of coherent and incoherent domains in systems that are structurally and spatially homogeneous. The recent realization that such states might be common in oscillator networks raises the question of whether an analogous phenomenon can occur in continuous media. Here, we show that chimera states can exist in continuous systems even when the coupling is strictly local, as in many fluid and pattern forming media. Using the complex Ginzburg-Landau equation as a model system, we characterize chimera states consisting of a coherent domain of a frozen spiral structure and an incoherent domain of amplitude turbulence. We show that in this case, in contrast with discrete network systems, fluctuations in the local coupling field play a crucial role in limiting the coherent regions. We suggest these findings shed light on new possible forms of coexisting order and disorder in fluid systems.

  7. Instructional Leadership Structure in Singapore: A Co-Existence of Hierarchy and Heterarchy

    Science.gov (United States)

    Nguyen, Dong Thanh; Ng, David; Yap, Pui San

    2017-01-01

    Purpose: The purpose of this paper is to explore the instructional leadership practices and structure in Singapore primary schools. Design/methodology/approach: The study employs a qualitative approach. Data were collected from interviews of 30 Singapore primary school principals and 25 working-day observations of five principals. A grounded…

  8. Research into zirconium alloys resistant to carbon dioxide under pressure at temperatures of up to 600 deg C (1963)

    International Nuclear Information System (INIS)

    Baque, P.; Dominget, R.; Bossard, J.

    1963-01-01

    Zirconium is a metal having a relatively low neutron capture cross-section and a high melting point; it is thus possible to consider its use in particular as a canning material for fuel elements in CO 2 -cooled nuclear reactors. A preliminary study of several types of zirconium showed that the metal is already strongly oxidised in this gas at 500 deg C. The 'breakaway' phenomenon is generalised; the oxidation rate is then linear and depends on the carbon dioxide pressure. An attempt was therefore made to find binary and tertiary alloys in order to improve the metal behaviour. Several interesting compositions were found: 1, 1.6 and 2.5 per cent of copper, 2 per cent of vanadium, and 0.05 and 0.5 per cent of calcium. Tertiary copper-molybdenum and copper-phosphorus alloys are also less liable to oxidation and in particular do not exhibit the 'breakaway' phenomenon even after a prolonged treatment at 600 deg C. (authors) [fr

  9. Modeling the effect of water vapor on the interfacial behavior of high-temperature air in contact with Fe20Cr surfaces

    International Nuclear Information System (INIS)

    Chialvo, Ariel A.; Brady, Michael P.; Keiser, James R.; Cole, David R.

    2011-01-01

    Highlights: → Atomistic view of the contrasting interfacial behavior between high-temperature dry- and wet-air in contact with stainless steels. → H 2 O preferentially adsorbs and displaces oxygen at the metal-fluid interface. → Findings are consistent with Ehlers et al.'s proposed competitive adsorption mechanism for the interpretation of the breakaway oxidation. → Significant impact of the inhomogeneous density distribution between the interfacial- and bulk-environments on the fluid transport. -- This work uses molecular dynamics simulation to provide an atomistic view of the contrasting interfacial behavior between high-temperature dry air and wet (10-40 vol.% water) air in contact with stainless steels. A key finding was that H 2 O preferentially adsorbs and displaces oxygen at the metal-fluid interface. We also discuss how these findings are consistent with Ehlers et al. proposed competitive adsorption mechanism for the interpretation of the breakaway oxidation, and highlight their impact on other properties.

  10. Specific experiments carried out in Germany in order to demonstrate the safety of existing structures

    International Nuclear Information System (INIS)

    Krutzik, Norbert

    2002-01-01

    Specific experiments are carried out in Germany in order to demonstrate the safety of existing NPPs. HDR research program includes operational loads testing (pressure test, pressure and temperature test, thermal shock, fatigue); extreme loads (earthquake, aircraft crash, external explosion); internal emergency loads (blowdown, hydrogen combustion, fire, thermal shock, water hammer, condensation loads)

  11. Investigation of the effectiveness of structural measures for reducing the radiation exposure of the population in aeras with enhanced natural radioactivity. A measuring campaign in existing buildings

    International Nuclear Information System (INIS)

    Leidner, L.; Urban, M.

    1986-01-01

    For this measuring campaign, buildings of different structural design located close to each other have been selected in an area with enhanced natural radioactivity in order to find out any differences in indoor radioactivity levels that can be attributed to structural design features. The measuring results show that the structural condition of the cellar is the decisive factor determining the radon concentration in a house for the case that the surrounding earth is the main radon source. In houses with an unimpaired concrete cellar flooring, radon concentrations in the ground floor have been found to be lower by a factor of 5-10 than in houses with a natural rock basement. Building materials have been found to have an effect at only comparably low radon concentrations. Expected impacts of structural measures, as e.g. thermal insulation windows, could not be proven (except for some half-timber buildings). The results of this measuring campaign that allow a direct house-to-house comparison do not confirm the relation between gamma dose rate and radon concentration postulated by results of a data collection campaign made in various administrative districts. The effectiveness of given structural variations cannot be proven by measurements in existing houses. This would rather require pin-pointed structural modifications for assessment, which can be done in a building chosen for this purpose. (orig./HP) [de

  12. Seismic evaluation of existing nuclear power plants

    International Nuclear Information System (INIS)

    2003-01-01

    The IAEA nuclear safety standards publications address the site evaluation and the design of new nuclear power plants (NPPs), including seismic hazard assessment and safe seismic design, at the level of the Safety Requirements as well as at the level of dedicated Safety Guides. It rapidly became apparent that the existing nuclear safety standards documents were not adequate for handling specific issues in the seismic evaluation of existing NPPs, and that a dedicated document was necessary. This is the purpose of this Safety Report, which is written in the spirit of the nuclear safety standards and can be regarded as guidance for the interpretation of their intent. Worldwide experience shows that an assessment of the seismic capacity of an existing operating facility can be prompted for the following: (a) Evidence of a greater seismic hazard at the site than expected before, owing to new or additional data and/or to new methods; (b) Regulatory requirements, such as periodic safety reviews, to ensure that the plant has adequate margins for seismic loads; (c) Lack of anti-seismic design or poor anti-seismic design; (d) New technical finding such as vulnerability of some structures (masonry walls) or equipment (relays), other feedback and new experience from real earthquakes. Post-construction evaluation programmes evaluate the current capability of the plant to withstand the seismic concern and identify any necessary upgrades or changes in operating procedures. Seismic qualification is distinguished from seismic evaluation primarily in that seismic qualification is intended to be performed at the design stage of a plant, whereas seismic evaluation is intended to be applied after a plant has been constructed. Although some guidelines do exist for the evaluation of existing NPPs, these are not established at the level of a regulatory guide or its equivalent. Nevertheless, a number of existing NPPs throughout the world have been and are being subjected to review of their

  13. Remark on state vector construction when flavor mixing exists

    International Nuclear Information System (INIS)

    Fujii, K.; Shimomura, T.

    2006-01-01

    In the framework of quantum field theory, we consider the way to construct the one-particle state (with definite 3-momentum) when particle mixing exists, such as in the case of flavor-neutrino mixing. In the preceding report (Prog. Theor. Phys. 112, 901 (2004)), we have examined the structure of expectation values of the flavor neutrino charges (at time t) with respect to a neutrino-source state prepared at time t' (earlier than t). When there is no mixing, each of various contributions to the expectation value is equal, in its dominant part, to the transition probability corresponding to the respective neutrino-production process. On the basis of the assumption that such an equality holds also in the mixing case, we can find an appropriate form of one-flavor-neutrino state with 3-momentum and helicity. Along the same way, we examine the boson case when flavor mixing exists. We give remarks on the relation and difference between the ordinary and the present approaches to flavor oscillation

  14. The introspective may achieve more: Enhancing existing Geoscientific models with native-language emulated structural reflection

    Science.gov (United States)

    Ji, Xinye; Shen, Chaopeng

    2018-01-01

    Geoscientific models manage myriad and increasingly complex data structures as trans-disciplinary models are integrated. They often incur significant redundancy with cross-cutting tasks. Reflection, the ability of a program to inspect and modify its structure and behavior at runtime, is known as a powerful tool to improve code reusability, abstraction, and separation of concerns. Reflection is rarely adopted in high-performance Geoscientific models, especially with Fortran, where it was previously deemed implausible. Practical constraints of language and legacy often limit us to feather-weight, native-language solutions. We demonstrate the usefulness of a structural-reflection-emulating, dynamically-linked metaObjects, gd. We show real-world examples including data structure self-assembly, effortless input/output (IO) and upgrade to parallel I/O, recursive actions and batch operations. We share gd and a derived module that reproduces MATLAB-like structure in Fortran and C++. We suggest that both a gd representation and a Fortran-native representation are maintained to access the data, each for separate purposes. Embracing emulated reflection allows generically-written codes that are highly re-usable across projects.

  15. Creation of Vapor/Gas Impermeable Coatings for CB Hardening of Existing Structures

    Science.gov (United States)

    2013-04-05

    Standard Test Method for Hydroxyl Groups Using Reaction with p-Toluenesulfonyl Isocyanate and Potentiometric Titration with Tetrabutylammonium...setup The structures of some resins produced as a result of the syntheses were confirmed by titration of their reactive terminal groups. This work...was conducted on a Mettler-Toledo DL-55 titrator . It must be noted that, as all the produced resins were new compounds that had never been

  16. Existence theory in optimal control

    International Nuclear Information System (INIS)

    Olech, C.

    1976-01-01

    This paper treats the existence problem in two main cases. One case is that of linear systems when existence is based on closedness or compactness of the reachable set and the other, non-linear case refers to a situation where for the existence of optimal solutions closedness of the set of admissible solutions is needed. Some results from convex analysis are included in the paper. (author)

  17. 10 CFR 4.127 - Existing facilities.

    Science.gov (United States)

    2010-01-01

    ... 10 Energy 1 2010-01-01 2010-01-01 false Existing facilities. 4.127 Section 4.127 Energy NUCLEAR... 1973, as Amended Discriminatory Practices § 4.127 Existing facilities. (a) Accessibility. A recipient... make each of its existing facilities or every part of an existing facility accessible to and usable by...

  18. Large-scale integration of wind power into the existing Chinese energy system

    DEFF Research Database (Denmark)

    Liu, Wen; Lund, Henrik; Mathiesen, Brian Vad

    2011-01-01

    stability, the maximum feasible wind power penetration in the existing Chinese energy system is approximately 26% from both technical and economic points of view. A fuel efficiency decrease occurred when increasing wind power penetration in the system, due to its rigid power supply structure and the task......This paper presents the ability of the existing Chinese energy system to integrate wind power and explores how the Chinese energy system needs to prepare itself in order to integrate more fluctuating renewable energy in the future. With this purpose in mind, a model of the Chinese energy system has...... been constructed by using EnergyPLAN based on the year 2007, which has then been used for investigating three issues. Firstly, the accuracy of the model itself has been examined and then the maximum feasible wind power penetration in the existing energy system has been identified. Finally, barriers...

  19. Leveraging Existing Mission Tools in a Re-Usable, Component-Based Software Environment

    Science.gov (United States)

    Greene, Kevin; Grenander, Sven; Kurien, James; z,s (fshir. z[orttr); z,scer; O'Reilly, Taifun

    2006-01-01

    Emerging methods in component-based software development offer significant advantages but may seem incompatible with existing mission operations applications. In this paper we relate our positive experiences integrating existing mission applications into component-based tools we are delivering to three missions. In most operations environments, a number of software applications have been integrated together to form the mission operations software. In contrast, with component-based software development chunks of related functionality and data structures, referred to as components, can be individually delivered, integrated and re-used. With the advent of powerful tools for managing component-based development, complex software systems can potentially see significant benefits in ease of integration, testability and reusability from these techniques. These benefits motivate us to ask how component-based development techniques can be relevant in a mission operations environment, where there is significant investment in software tools that are not component-based and may not be written in languages for which component-based tools even exist. Trusted and complex software tools for sequencing, validation, navigation, and other vital functions cannot simply be re-written or abandoned in order to gain the advantages offered by emerging component-based software techniques. Thus some middle ground must be found. We have faced exactly this issue, and have found several solutions. Ensemble is an open platform for development, integration, and deployment of mission operations software that we are developing. Ensemble itself is an extension of an open source, component-based software development platform called Eclipse. Due to the advantages of component-based development, we have been able to vary rapidly develop mission operations tools for three surface missions by mixing and matching from a common set of mission operation components. We have also had to determine how to

  20. Normal-Faulting in Madagascar: Another Round of Continental Rifting?

    Science.gov (United States)

    Wysession, M. E.; Pratt, M. J.; Tsiriandrimanana, R.; Andriampenomanana Ny Ony, F. S. T.; Nyblade, A.; Durrheim, R. J.; Tilmann, F. J.; Rumpker, G.; Rambolamanana, G.; Aleqabi, G. I.; Shore, P.

    2017-12-01

    Analyses of seismicity and seismic structure within Madagascar suggest the current occurrence of crustal extension, which may be related to continental rifting associated with a diffuse boundary between the Somalia and Lwandle tectonic plates. Madagascar has participated in two major rifting events as part of the break-up of Gondwana: the break-away of Greater India (Madagascar, India, the Seychelles) away from mainland Africa during the Jurassic and the break-away of India from Madagascar during the Cretaceous. Seismic activity and the structures obtained from it, using data from the 2-year (2011-2013) MACOMO project, suggest that this break-up may not be finished, and that continental rifts may be developing again. There are fairly high levels of intraplate seismicity within Madagascar: over 800 events located during the 22 months of the deployment. For comparison, a 2-year deployment of seismometers within the upper Midwest of the U.S. yielded just 12 intraplate earthquakes. While the Madagascar seismicity occurs across the island, it is strongly concentrated in the central region, where Cenozoic volcanism has occurred through the Holocene, and earthquakes align along N-S-trending lineations associated with N-S-trending pull-apart graben structures. The thickness of the crust is still >40 km in this region, but it is underlain by a large low-velocity structure within the lithosphere and asthenosphere that is observed in our studies of surface-wave, body-wave, and Pn-phase tomography. Normal faulting is not observed everywhere on the island, however; seismicity in the north is largely strike-slip, and seismicity in the south appears to be largely reverse faulting. Several studies have suggested that the diffuse boundary between the Somalia and Lwandle plates runs roughly E-W across Madagascar. Extensional faulting seems to predominate only within central Madagascar, likely associated with the current volcanic activity, which also appears to be associated with the

  1. The use of lifetime functions in the optimization of interventions on existing bridges considering maintenance and failure costs

    Energy Technology Data Exchange (ETDEWEB)

    Yang, Seung-Ie [Department of Civil, Enviromental, and Architectural Enginnering, University of Colorado, Campus Box 428, Boulder, CO 80309-0428 (United States)]. E-mail: yangsione@dreamwiz.com; Frangopol, Dan M. [Department of Civil, Enviromental, and Architectural Enginnering, University of Colorado, Campus Box 428, Boulder, CO 80309-0428 (United States)]. E-mail: dan.frangopol@colorado.edu; Kawakami, Yoriko [Hanshin Expressway Public Corporation, Kobe Maintenance Department, 16-1 Shinko-cho Chuo-ku Kobe City, Hyogo, 650-0041 (Japan)]. E-mail: yoriko-kawakami@hepc.go.jp; Neves, Luis C. [Department of Civil, Enviromental, and Architectural Enginnering, University of Colorado, Campus Box 428, Boulder, CO 80309-0428 (United States)]. E-mail: lneves@civil.uminho.pt

    2006-06-15

    In the last decade, it became clear that life-cycle cost analysis of existing civil infrastructure must be used to optimally manage the growing number of aging and deteriorating structures. The uncertainties associated with deteriorating structures require the use of probabilistic methods to properly evaluate their lifetime performance. In this paper, the deterioration and the effect of maintenance actions are analyzed considering the performance of existing structures characterized by lifetime functions. These functions allow, in a simple manner, the consideration of the effect of aging on the decrease of the probability of survival of a structure, as well as the effect of maintenance actions. Models for the effects of proactive and reactive preventive maintenance, and essential maintenance actions are presented. Since the probability of failure is different from zero during the entire service life of a deteriorating structure and depends strongly on the maintenance strategy, the cost of failure is included in this analysis. The failure of one component in a structure does not usually lead to failure of the structure and, as a result, the safety of existing structures must be analyzed using a system reliability framework. The optimization consists of minimizing the sum of the cumulative maintenance and expected failure cost during the prescribed time horizon. Two examples of application of the proposed methodology are presented. In the first example, the sum of the maintenance and failure costs of a bridge in Colorado is minimized considering essential maintenance only and a fixed minimum acceptable probability of failure. In the second example, the expected lifetime cost, including maintenance and expected failure costs, of a multi-girder bridge is minimized considering reactive preventive maintenance actions.

  2. The use of lifetime functions in the optimization of interventions on existing bridges considering maintenance and failure costs

    International Nuclear Information System (INIS)

    Yang, Seung-Ie; Frangopol, Dan M.; Kawakami, Yoriko; Neves, Luis C.

    2006-01-01

    In the last decade, it became clear that life-cycle cost analysis of existing civil infrastructure must be used to optimally manage the growing number of aging and deteriorating structures. The uncertainties associated with deteriorating structures require the use of probabilistic methods to properly evaluate their lifetime performance. In this paper, the deterioration and the effect of maintenance actions are analyzed considering the performance of existing structures characterized by lifetime functions. These functions allow, in a simple manner, the consideration of the effect of aging on the decrease of the probability of survival of a structure, as well as the effect of maintenance actions. Models for the effects of proactive and reactive preventive maintenance, and essential maintenance actions are presented. Since the probability of failure is different from zero during the entire service life of a deteriorating structure and depends strongly on the maintenance strategy, the cost of failure is included in this analysis. The failure of one component in a structure does not usually lead to failure of the structure and, as a result, the safety of existing structures must be analyzed using a system reliability framework. The optimization consists of minimizing the sum of the cumulative maintenance and expected failure cost during the prescribed time horizon. Two examples of application of the proposed methodology are presented. In the first example, the sum of the maintenance and failure costs of a bridge in Colorado is minimized considering essential maintenance only and a fixed minimum acceptable probability of failure. In the second example, the expected lifetime cost, including maintenance and expected failure costs, of a multi-girder bridge is minimized considering reactive preventive maintenance actions

  3. Effect of water vapor on annealing scale formation on 316 SS

    International Nuclear Information System (INIS)

    Cheng, S.-Y.; Kuan, S.-L.; Tsai, W.-T.

    2006-01-01

    The oxidation behavior of 316 stainless steel (SS) annealed in air containing 0.1 atm water vapor at temperatures ranging from 800 to 1030 deg. C was investigated. A kinetic study of the oxidation was made by employing thermal-gravimetric analysis (TGA). The morphology, composition and structure of the scale were examined by scanning electron microscopy (SEM) and X-ray diffraction (XRD). The experimental results showed that significant breakaway oxidation occurred, resulting in substantial weight increase, as the steel was annealed in moist air at temperatures above 950 deg. C. The scaling behavior of 316 SS in wet air at 1030 deg. C could be divided into two stages based on the alteration of the oxidation rate. In each stage, the scale on 316 SS exhibited a different structure and morphology. The complex process of the formation of scale in wet air was discussed and proposed

  4. Simplified Assessment of R3 Nominal Assurance Degree to Seismic Action of the Existing Masonry Dwellings

    Directory of Open Access Journals (Sweden)

    Teodor Broşteanu

    2008-01-01

    Full Text Available This paper refers to the assessment of the performance level of a building for a given seismic hazard level. Building performance level describes the expected seismic performance given by the computation of R3 Nominal Assurance Degree to Seismic Action of the Existing Masonry Dwellings and Monumental Buildings according to the Romanian Norm P100:1992 [1], modified on 1996 with the chapters 11 and 12, until the Part 3 of P100-1:2006 [2], will be performed for the Assessment and Strengthening Structural Design of the Seismic Vulnerable, Existing Buildings, in the frame of SR EN 1998-1:2004 EC8 [3]. The framing of damages into the potential risk degrees has a social and economic impact. Assessment and retrofitting of the existing buildings have represented a huge engineering challenge as a distinct problem versus a new building design. The performance level of a vulnerable existing building shows us the expected seismic performance level due to the classified damages, the pattern of cracks, the interruption of function, the economic losses and the needed interventions, all in function of the importance class of building on next life span of use. On recommends the computation of R (R3 Nominal Assurance Degree to Seismic Action of the Vulnerable Dwellings for the assessing and strengthening design, in comparison to both norms because of the bearing conventional seismic load computed by [1], will result less than the value which will be computed by the Part 3 of P100-1:2006, i.e. the norm P100:1992 is more severe. In the case of the breakable fracture probability of the existing structural masonry members, one recommends a bigger value of ? – reduction factor unless the given values by [1] for a new structure with a high ductility, especially for the deflections calibration on the same limit state.

  5. Compilation of Existing Neutron Screen Technology

    Directory of Open Access Journals (Sweden)

    N. Chrysanthopoulou

    2014-01-01

    Full Text Available The presence of fast neutron spectra in new reactors is expected to induce a strong impact on the contained materials, including structural materials, nuclear fuels, neutron reflecting materials, and tritium breeding materials. Therefore, introduction of these reactors into operation will require extensive testing of their components, which must be performed under neutronic conditions representative of those expected to prevail inside the reactor cores when in operation. Due to limited availability of fast reactors, testing of future reactor materials will mostly take place in water cooled material test reactors (MTRs by tailoring the neutron spectrum via neutron screens. The latter rely on the utilization of materials capable of absorbing neutrons at specific energy. A large but fragmented experience is available on that topic. In this work a comprehensive compilation of the existing neutron screen technology is attempted, focusing on neutron screens developed in order to locally enhance the fast over thermal neutron flux ratio in a reactor core.

  6. Excavation-caused extra deformation of existing masonry residence in soft soil region

    Science.gov (United States)

    Tang, Y.; Franceschelli, S.

    2017-04-01

    Growing need for construction of infrastructures and buildings in fast urbanization process creates challenges of interaction between buildings under construction and adjacent existing buildings. This paper presents the mitigation of contradiction between two parties who are involved the interaction using civil engineering techniques. Through the in-depth analysis of the results of monitoring surveys and enhanced accuracy and reliability of surveys, a better understanding of the behavior of deformable buildings is achieved. Combination with the original construction documents, the two parties agree that both of them are responsible for building damages and a better understanding for the rehabilitation of the existing buildings is focused on. Two cases studies are used to demonstrate and describe the importance of better understanding of the behavior of existing buildings and their rehabilitations. The objective of this study is to insight into mechanisms of soil-structure interaction for buildings adjacent to deep excavations, which can result in a damage in existing masonry residence, and to take the optimized measures to make deep excavations safety and economic and adjacent buildings keep good serviceability in urban areas with soft soil conditions.

  7. 14 CFR 1251.301 - Existing facilities.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 5 2010-01-01 2010-01-01 false Existing facilities. 1251.301 Section 1251... HANDICAP Accessibility § 1251.301 Existing facilities. (a) Accessibility. A recipient shall operate each... existing facilities or every part of a facility accessible to and usable by handicapped persons. (b...

  8. 10 CFR 611.206 - Existing facilities.

    Science.gov (United States)

    2010-01-01

    ... 10 Energy 4 2010-01-01 2010-01-01 false Existing facilities. 611.206 Section 611.206 Energy... PROGRAM Facility/Funding Awards § 611.206 Existing facilities. The Secretary shall, in making awards to those manufacturers that have existing facilities, give priority to those facilities that are oldest or...

  9. A precariedade humana e a existência estilizada Human precariousness and stylized existence

    Directory of Open Access Journals (Sweden)

    Rita Paiva

    2013-04-01

    Full Text Available Este artigo tematiza o desamparo vivenciado pela consciência ante a ausência de bases sólidas para seus anseios de felicidade e para suas representações simbólicas. Com esse propósito, toma como objeto de reflexão um dos ensaios filosóficos de Albert Camus, O mito de Sísifo, equacionando a possibilidade de uma ética que estilize a vida, sem que se minimize a dolorosa precariedade da existência humana. Posteriormente, em diálogo com alguns textos de M. Foucault, a reflexão procura estabelecer os vínculos possíveis entre a ética camusiana e a ética como uma estética da existência, tal como pensada entre os gregos antigos.This article discusses the helplessness experienced by the consciousness vis-à-vis the absence of solid bases for its longings for happiness and for its symbolic representations. For this purpose, the object of reflection of the article is one of Albert Camus' philosophical essays, The Myth of Sisyphus, and we inquire into the possibility of an ethics that stylizes life without minimizing the painful precariousness of human existence. Making reference to certain texts by Foucault, we attempt to establish possible connections between Camus' ethics and an ethics of the aesthetics of existence as found in the thinkers of ancient Greece.

  10. 45 CFR 1170.32 - Existing facilities.

    Science.gov (United States)

    2010-10-01

    ... 45 Public Welfare 3 2010-10-01 2010-10-01 false Existing facilities. 1170.32 Section 1170.32... ASSISTED PROGRAMS OR ACTIVITIES Accessibility § 1170.32 Existing facilities. (a) Accessibility. A recipient... require a recipient to make each of its existing facilities or every part of a facility accessible to and...

  11. 45 CFR 605.22 - Existing facilities.

    Science.gov (United States)

    2010-10-01

    ... 45 Public Welfare 3 2010-10-01 2010-10-01 false Existing facilities. 605.22 Section 605.22 Public... Accessibility § 605.22 Existing facilities. (a) Accessibility. A recipient shall operate each program or... existing facilities or every part of a facility accessible to and usable by qualified handicapped persons...

  12. 45 CFR 1151.22 - Existing facilities.

    Science.gov (United States)

    2010-10-01

    ... 45 Public Welfare 3 2010-10-01 2010-10-01 false Existing facilities. 1151.22 Section 1151.22... Prohibited Accessibility § 1151.22 Existing facilities. (a) A recipient shall operate each program or... make each of its existing facilities or every part of a facility accessible to and usable by...

  13. Existence and non-existence of solutions for a p(x-biharmonic problem

    Directory of Open Access Journals (Sweden)

    Ghasem A. Afrouzi

    2015-06-01

    Full Text Available In this article, we study the following problem with Navier boundary conditions $$\\displaylines{ \\Delta (|\\Delta u|^{p(x-2}\\Delta u+|u|^{p(x-2}u =\\lambda |u|^{q(x-2}u +\\mu|u|^{\\gamma(x-2}u\\quad \\text{in } \\Omega,\\cr u=\\Delta u=0 \\quad \\text{on } \\partial\\Omega. }$$ where $\\Omega$ is a bounded domain in $\\mathbb{R}^{N}$ with smooth boundary $\\partial \\Omega$, $N\\geq1$. $p(x,q(x$ and $\\gamma(x$ are continuous functions on $\\overline{\\Omega}$, $\\lambda$ and $\\mu$ are parameters. Using variational methods, we establish some existence and non-existence results of solutions for this problem.

  14. Investigation of the high temperature steam oxidation of Zircaloy 4 cladding tubes

    International Nuclear Information System (INIS)

    Leistikow, S.; Berg, H. v.; Kraft, R.; Pott, E.; Schanz, G.

    1979-01-01

    Also for the ORNL Zircaloy 4 cladding material, an intermediate decrease of the proportion of the ZrO 2 /α-phase layer was found, followed by an drastic increase when the breakaway of the ZrO 2 -scale occurred. Other reasons for small divergencies were evaluated, for instance temperature and time measurements, metallographic evaluation of layer thicknesses, consequences of one-sided (ORNL) and double-sided (KfK) oxidation. The so-called anomalous effect of steam oxidation during temperature transients was reproduced qualitatively and-in case that a reduced gain of oxygen was observed-explained by the predominant existence of the monoclinic oxide phase. The creep-rupture tests below 800 0 C showed a moderate prolongation of time-to-rupture when the tests were performed in steam (or after preoxidation in steam) instead of argon. Also slightly reduced maximum circumferential strain could be measured. (orig./RW) [de

  15. 34 CFR 104.22 - Existing facilities.

    Science.gov (United States)

    2010-07-01

    ... 34 Education 1 2010-07-01 2010-07-01 false Existing facilities. 104.22 Section 104.22 Education... Accessibility § 104.22 Existing facilities. (a) Accessibility. A recipient shall operate its program or activity.... This paragraph does not require a recipient to make each of its existing facilities or every part of a...

  16. Evaluation of Existing Structure and Civil Protection Management Framework in Greek Local Authorities: A Questionnaire Survey Demonstrates Why Prevention Fails

    Science.gov (United States)

    Papanikolaou, Dimitrios; Papanikolaou, Ioannis; Diakakis, Michalis; Deligiannakis, Georgios

    2013-04-01

    In the face of a growing number of natural disasters and the increasing costs associated with them, Europe and Greece in particular, have devoted significant efforts and resources in natural hazards mitigation during the last decades. Despite the significant legislative efforts (e.g. 1998/22/EC, 2001/792/EC, 2007/60/EC Directives, 3013/2002 Act) and even though a number of steps has been taken towards improving civil protection, recent catastrophic events have illustrated the weaknesses of current approaches. In particular, in Greece, events such as the 1999 Athens earthquake, the 2007 and 2009 wildfires have shown the inadequacy of prevention and mitigation practices. Given the enhanced civil protection responsibilities, given by the Greek national law (Acts 3013/2002, 3852/2010) to local authorities in Greece, this work analyses and evaluates the existing structure and current management framework under which local authorities function and examines their risk mitigation practices. We conducted the largest questionnaire survey regarding Civil Protections issues, among the municipalities of Greece. To this aim, this work used a innovative online tool to assess current framework. Therefore, a network connecting civil protection departments of municipalities was developed, based on an Internet platform that acted also as a communication tool. Overall, we had feedback either online or offline from 125 municipalities across the country (representing more than one/third of the total municipalities of Greece). Through this network, municipal civil protection officials completed surveys designed to obtain and quantify information on several aspects of civil protection practices and infrastructure. In particular, the examined factors included: (i) personnel and equipment, (ii) inter-agency cooperation, (iii) training, (iv) compliance with existing regulations and (v) persistent problems encountered by civil protection departments, that prevent the effectiveness of current

  17. The North Caucasus Insurgency: Dead or Alive

    Science.gov (United States)

    2017-02-01

    II. Chechnya 2000–2010: A Model Counterinsurgency?............................................35 III. Counterinsurgency...following the Russian Army’s incursion into the breakaway republic of Chechnya . Within less than a decade, what began as a local ethno-separatist...rebel- lion effectively morphed into an Islamist insurgency, spreading in the early-2000s from Chechnya to most of the Muslim-majority region

  18. On the Existence and Uniqueness of JML Estimates for the Partial Credit Model

    Science.gov (United States)

    Bertoli-Barsotti, Lucio

    2005-01-01

    A necessary and sufficient condition is given in this paper for the existence and uniqueness of the maximum likelihood (the so-called joint maximum likelihood) estimate of the parameters of the Partial Credit Model. This condition is stated in terms of a structural property of the pattern of the data matrix that can be easily verified on the basis…

  19. THEORETICAL INVESTIGATION OF MICROSTRUCTURE EVOLUTION AND DEFORMATION OF ZIRCONIUM UNDER CASCADE DAMAGE CONDITIONS

    Energy Technology Data Exchange (ETDEWEB)

    Barashev, Alexander V [ORNL; Golubov, Stanislav I [ORNL; Stoller, Roger E [ORNL

    2012-06-01

    This work is based on our reaction-diffusion model of radiation growth of Zr-based materials proposed recently in [1]. In [1], the equations for the strain rates in unloaded pure crystal under cascade damage conditions of, e.g., neutron or heavy-ion irradiation were derived as functions of dislocation densities, which include contributions from dislocation loops, and spatial distribution of their Burgers vectors. The model takes into account the intra-cascade clustering of self-interstitial atoms and their one-dimensional diffusion; explains the growth stages, including the break-away growth of pre-annealed samples; and accounts for some striking observations, such as of negative strain in prismatic direction, and co-existence of vacancy- and interstitial-type prismatic loops. In this report, the change of dislocation densities due to accumulation of sessile dislocation loops is taken into account explicitly to investigate the dose dependence of radiation growth. The dose dependence of climb rates of dislocations is calculated, which is important for the climb-induced glide model of radiation creep. The results of fitting the model to available experimental data and some numerical calculations of the strain behavior of Zr for different initial dislocation structures are presented and discussed. The computer code RIMD-ZR.V1 (Radiation Induced Microstructure and Deformation of Zr) developed is described and attached to this report.

  20. Financial Management: Existence of U.S. Army Corps of Engineers Buildings and Other Structures

    National Research Council Canada - National Science Library

    Granetto, Paul J; Pusey, Ryan W; Ventimiglia, Crmelo G; Zeh, William H; Bryant, Leon D; King, Calvin O; Kntor, Scott C; Kasseler, Trisha L

    2005-01-01

    ...) cost and the associated accumulated depreciation of the assets. As of September 30, 2003, USACE had about 40,000 structures located at about 1,273 field sites in the continental United States, Alaska, and Hawaii.

  1. The Dual Half-Arc data structure: towards the universal B-rep data structure

    DEFF Research Database (Denmark)

    Anton, François; Bugoslawski, P.; Mioc, Darka

    2014-01-01

    , or more generally, the topology of any topological space. For this purpose, we generalize an existing data structure from 2D to 3D and design a new 3D data structure that realizes the synthesis between an existing 3D data structure (the Dual Half-Edge (See Footonote 1) data structure) and the generalized...... 3D Quad-Arc data structure, (See Footonote 2) and at the same time, improves the Dual Half-Edge towards a simpler and more effective representation of cell complexes through B-rep structures. We generalize the idea of the Quad-Arc data structure from 2D to 3D, but instead of transforming a simple...... edge of the Quad-Edge data structure to an arc with multiple points along it, we group together primal edges of the Dual Half-Edge that have the same dual Half-Edge vertex tags (volume tags) into one Dual Half-Arc whose dual is the common Dual Half-Edge and primal faces corresponding to dual...

  2. Defining the Field of Existence of Shrouded Blades in High-Speed Gas Turbines

    Science.gov (United States)

    Belousov, Anatoliy I.; Nazdrachev, Sergeiy V.

    2018-01-01

    This work provides a method for determining the region of existence of banded blades of gas turbines for aircraft engines based on the analytical evaluation of tensile stresses in specific characteristic sections of the blade. This region is determined by the set of values of the parameter, which forms the law of distribution of the cross-sectional area of the cross-sections along the height of the airfoil. When seven independent parameters (gas-dynamic, structural and strength) are changed, the choice of the best option is proposed at the early design stage. As an example, the influence of the dimension of a turbine on the domain of the existence of banded blades is shown.

  3. Rotating shallow water modeling of planetary,astrophysical and plasma vortical structures (plasma transport across a magnetic field,model of the jupiter's GRS, prediction of existence of giant vortices in spiral galaxies

    Directory of Open Access Journals (Sweden)

    M. V. Nezlin

    1999-01-01

    Full Text Available Three kinds of results have been described in this paper. Firstly, an experimental study of the Rossby vortex meridional drift on the rotating shallow water has been carried out. Owing to the stringent physical analogy between the Rossby vortices and drift vortices in the magnetized plasma, the results obtained have allowed one to make a conclusion that the transport rate of the plasma, trapped by the drift vortices, across the magnetic field is equivalent to the “gyro-Bohm” diffusion coefficient. Secondly, a model of big vortices of the type of the Great Red Spot of Jupiter, dominating in the atmospheres of the outer planets, has been produced. Thirdly, the rotating shallow water modeling has been carried out of the hydrodynamical generation mechanism of spiral structures in galaxies. Trailing spiral waves of various azimuthal modes, generated by a shear flow between fast rotating “nucleus” and slow rotating periphery, were produced. The spirals are similar to those existing in the real galaxies. The hydrodynamical concept of the spiral structure formation in galaxies has been substantiated. Strong anticyclonic vortices between the spiral arms of the structures under study have been discovered for the first time. The existence of analogous vortices in real galaxies has been predicted. (This prediction has been reliably confirmed recently in special astronomical observations, carried out on the basis of the mentioned laboratory modeling and the prediction made – see the paper by A. Fridman et al. (Astrophysics and Space Science, 1997, 252, 115.

  4. Existing Steel Railway Bridges Evaluation

    Science.gov (United States)

    Vičan, Josef; Gocál, Jozef; Odrobiňák, Jaroslav; Koteš, Peter

    2016-12-01

    The article describes general principles and basis of evaluation of existing railway bridges based on the concept of load-carrying capacity determination. Compared to the design of a new bridge, the modified reliability level for existing bridges evaluation should be considered due to implementation of the additional data related to bridge condition and behaviour obtained from regular inspections. Based on those data respecting the bridge remaining lifetime, a modification of partial safety factors for actions and materials could be respected in the bridge evaluation process. A great attention is also paid to the specific problems of determination of load-caring capacity of steel railway bridges in service. Recommendation for global analysis and methodology for existing steel bridge superstructure load-carrying capacity determination are described too.

  5. Earth's Largest Terrestrial Landslide (The Markagunt Gravity Slide of Southwest Utah): Insights from the Catastrophic Collapse of a Volcanic Field

    Science.gov (United States)

    Hacker, D. B.; Biek, R. F.; Rowley, P. D.

    2015-12-01

    The newly discovered Miocene Markagunt gravity slide (MGS; Utah, USA) represents the largest volcanic landslide structure on Earth. Recent geologic mapping of the MGS indicates that it was a large contiguous volcanic sheet of allochthonous andesitic mudflow breccias and lava flows, volcaniclastic rocks, and intertonguing regional ash-flow tuffs that blanketed an area of at least 5000 km2 with an estimated volume of ~3000 km3. From its breakaway zone in the Tushar and Mineral Mountains to its southern limits, the MGS is over 95 km long and at least 65 km wide. The MGS consists of four distinct structural segments: 1) a high-angle breakaway segment, 2) a bedding-plane segment, ~60 km long and ~65 km wide, typically located within the volcaniclastic Eocene-Oligocene Brian Head Formation, 3) a ramp segment ~1-2 km wide where the slide cuts upsection, and 4) a former land surface segment where the upper-plate moved at least 35 km over the Miocene landscape. The presence of basal and lateral cataclastic breccias, clastic dikes, jigsaw puzzle fracturing, internal shears, pseudotachylytes, and the overall geometry of the MGS show that it represents a single catastrophic emplacement event. The MGS represents gravitationally induced collapse of the southwest sector of the Oligocene to Miocene Marysvale volcanic field. We suggest that continuous growth of the Marysvale volcanic field, loading more volcanic rocks on a structurally weak Brian Head basement, created conditions necessary for gravity sliding. In addition, inflation of the volcanic pile due to multiple magmatic intrusions tilted the strata gently southward, inducing lateral spreading of the sub-volcanic rocks prior to failure. Although similar smaller-scale failures have been recognized from individual volcanoes, the MGS represents a new class of low frequency but high impact hazards associated with catastrophic sector collapse of large volcanic fields containing multiple volcanoes. The relationship of the MGS to

  6. Do Elementary Particles Have an Objective Existence?

    OpenAIRE

    Nissenson, Bilha

    2007-01-01

    The formulation of quantum theory does not comply with the notion of objective existence of elementary particles. Objective existence independent of observation implies the distinguishability of elementary particles. In other words: If elementary particles have an objective existence independent of observations, then they are distinguishable. Or if elementary particles are indistinguishable then matter cannot have existence independent of our observation. This paper presents a simple deductio...

  7. Cirripede Cypris Antennules: How Much Structural Variation Exists Among Balanomorphan Species from Hard-Bottom Habitats?

    Science.gov (United States)

    Chan, Benny K K; Sari, Alireza; Høeg, Jens T

    2017-10-01

    Barnacle cypris antennules are important for substratum attachment during settlement and on through metamorphosis from the larval stage to sessile adult. Studies on the morphology of cirripede cyprids are mostly qualitative, based on descriptions from images obtained using a scanning electron microscope (SEM). To our knowledge, our study is the first to use scanning electron microscopy to quantify overall structural diversity in cypris antennules by measuring 26 morphological parameters, including the structure of sensory organs. We analyzed cyprids from seven species of balanomorphan barnacles inhabiting rocky shore communities; for comparison, we also included a sponge-inhabiting balanomorphan and a verrucomorphan species. Multivariate analysis of the structural parameters resulted in two distinct clusters of species. From nonmetric multidimensional scaling plots, the sponge-inhabiting Balanus spongicola and Verruca stroemia formed one cluster, while the other balanomorphan species, all from hard bottoms, grouped together in the other cluster. The shape of the attachment disk on segment 3 is the key parameter responsible for the separation into two clusters. The present results show that species from a coastal hard-bottom habitat may share a nearly identical antennular structure that is distinct from barnacles from other habitats, and this finding supports the fact that such species also have rather similar reactions to substratum cues during settlement. Any differences that may be found in settlement biology among such species must therefore be due either to differences in the properties of their adhesive mechanisms or to the way that sensory stimuli are detected by virtually identical setae and processed into settlement behavior by the cyprid.

  8. Existing Steel Railway Bridges Evaluation

    Directory of Open Access Journals (Sweden)

    Vičan Josef

    2016-12-01

    Full Text Available The article describes general principles and basis of evaluation of existing railway bridges based on the concept of load-carrying capacity determination. Compared to the design of a new bridge, the modified reliability level for existing bridges evaluation should be considered due to implementation of the additional data related to bridge condition and behaviour obtained from regular inspections. Based on those data respecting the bridge remaining lifetime, a modification of partial safety factors for actions and materials could be respected in the bridge evaluation process. A great attention is also paid to the specific problems of determination of load-caring capacity of steel railway bridges in service. Recommendation for global analysis and methodology for existing steel bridge superstructure load-carrying capacity determination are described too.

  9. Existence of equilibria in articulated bearings

    Science.gov (United States)

    Buscaglia, G.; Ciuperca, I.; Hafidi, I.; Jai, M.

    2007-04-01

    The existence of equilibrium solutions for a lubricated system consisting of an articulated body sliding over a flat plate is considered. Though this configuration is very common (it corresponds to the popular tilting-pad thrust bearings), the existence problem has only been addressed in extremely simplified cases, such as planar sliders of infinite width. Our results show the existence of at least one equilibrium for a quite general class of (nonplanar) slider shapes. We also extend previous results concerning planar sliders.

  10. LANDFIRE 2015 Remap – Utilization of Remotely Sensed Data to Classify Existing Vegetation Type and Structure to Support Strategic Planning and Tactical Response

    Science.gov (United States)

    Picotte, Joshua J.; Long, Jordan; Peterson, Birgit; Nelson, Kurtis

    2017-01-01

    The LANDFIRE Program produces national scale vegetation, fuels, fire regimes, and landscape disturbance data for the entire U.S. These data products have been used to model the potential impacts of fire on the landscape [1], the wildfire risks associated with land and resource management [2, 3], and those near population centers and accompanying Wildland Urban Interface zones [4], as well as many other applications. The initial LANDFIRE National Existing Vegetation Type (EVT) and vegetation structure layers, including vegetation percent cover and height, were mapped circa 2001 and released in 2009 [5]. Each EVT is representative of the dominant plant community within a given area. The EVT layer has since been updated by identifying areas of landscape change and modifying the vegetation types utilizing a series of rules that consider the disturbance type, severity of disturbance, and time since disturbance [6, 7]. Non-disturbed areas were adjusted for vegetation growth and succession. LANDFIRE vegetation structure layers also have been updated by using data modeling techniques [see 6 for a full description]. The subsequent updated versions of LANDFIRE include LANDFIRE 2008, 2010, 2012, and LANDFIRE 2014 is being incrementally released, with all data being released in early 2017. Additionally, a comprehensive remap of the baseline data, LANDFIRE 2015 Remap, is being prototyped, and production is tentatively planned to begin in early 2017 to provide a more current baseline for future updates.

  11. Edible fat structures at high solid fat concentrations: Evidence for the existence of oil-filled nanospaces

    Science.gov (United States)

    Peyronel, Fernanda; Quinn, Bonnie; Marangoni, Alejandro G.; Pink, David A.

    2015-01-01

    We have characterized the surfaces of grain boundaries in edible oils with high solid fat content by combining ultra-small angle x-ray scattering (USAXS) with theoretical modelling and computer simulation. Our results will lead to understand the solid structures formed at the time of manufacturing fats like confectionery fats as well as pave the way for the engineering of innovative fat products. Edible fats are complex semi-solid materials where a solid structure entraps liquid oil. It was not until USAXS combined with modelling was used that the nano- to meso-structures for systems with less than 20% solids were understood. The interpretation of those results utilized models of crystalline nanoplatelets represented by rigid close-packed flat aggregates made of spheres and was allowed to aggregate using the Metropolis Monte Carlo technique. Here, we report on systems containing between 50% and 90% solids. We modelled the solid phase as being formed from seeds onto which solids condensed thereby giving rise to oil-filled nanospaces. The models predicted that the system (a) exhibits structures with fractal dimensions approximately 2, (b) a broad peak somewhat masking that slope, and (c) for smaller values of q, indications that the structures with fractal dimension approximately 2 are uniformly distributed in space. The interpretation of the experimental data was completely driven by these results. The computer simulation predictions were used in conjunction with the USAXS observations to conclude that the systems studied scattered from oil-cavities with sizes between ˜800 and ˜16 000 Å and possessed rough 2-dimensional walls.

  12. Oxidation behaviour of titanium in high temperature steam

    International Nuclear Information System (INIS)

    Moroishi, Taishi; Shida, Yoshiaki

    1978-01-01

    The oxidation of pure titanium was studied in superheated steam at 400 -- 550 0 C. The effects of prior cold working and several heat treatment conditions on the oxidation were examined and also the effects of the addition of small amounts of iron and oxygen were investigated. The oxidation mechanism of pure titanium is discussed in relation to the scale structure and the oxidation kinetics. Hydrogen absorption rate was also measured. As a result, the following conclusions were drawn: (1) The oxidation of pure titanium in steam was faster than in air and breakaway oxidation was observed above 500 0 C after the specimen had gained a certain weight. Prior cold working and heat treatment conditions scarcely affected the oxidation rate, whereas the specimen containing small amounts of iron and oxygen showed a little more rapid oxidation. (2) At 500 and 550 0 C a dark grey inner scale and a yellow-brown outer scale were formed. The outer scale was apt to exfoliate after the occurrence of breakaway oxidation. At 400 and 450 0 C only a dark grey scale was observed. All of these oxides were identified as the rutile type, TiO 2 . Furthermore, the presence of a thin and uniform oxygen rich layer beneath the external scale was confirmed at all test temperatures. (3) The measured weight gain approximately followed the cubic rate law; this would be expected for the following reason; one component of the weight gain is due to the dissolved oxygen, the amount of which remains constant after the early stages of oxidation. The second component is due to the parabolic growth of the external TiO 2 scale. When these contributions are added a pseudo-cubic weight gain curve results. (4) It was shown that 50 percent of the hydrogen generated during the oxidation was absorbed into the metal. (auth.)

  13. 45 CFR 84.22 - Existing facilities.

    Science.gov (United States)

    2010-10-01

    ... HANDICAP IN PROGRAMS OR ACTIVITIES RECEIVING FEDERAL FINANCIAL ASSISTANCE Accessibility § 84.22 Existing facilities. (a) Accessibility. A recipient shall operate its program or activity so that when each part is..., welfare, or other social services at alternate accessible sites, alteration of existing facilities and...

  14. Mathematical model of drift deposition from a bifurcated cooling tower plume

    International Nuclear Information System (INIS)

    Chen, N.C.J.; Jung, L.

    1978-01-01

    Cooling tower drift deposition modeling has been extended by including centrifugal force induced through plume bifurcation in a crosswind as a mechanism for drift droplet removal from the plume. The model, in its current state of development, is capable of predicting the trajectory of a single droplet from the stage of strong interaction with the vortex field soon after droplet emission at the tower top through the stage of droplet evaporation in an unsaturated atmosphere after droplet breakaway from the plume. The computer program developed from the mathematical formulation has been used to explore the dependency of the droplet trajectory on droplet size, vortex strength, point of droplet emission, drag coefficient, droplet efflux speed, and ambient conditions. A specific application to drift from a mechanical-draft cooling tower (for a wind speed twice the efflux speed, a relative humidity of 70 per cent, and an initial droplet radius of 100 μm) showed the droplet to follow a helical trajectory within the plume, with breakaway occurring at 2.5 tower diameters downwind and ground impact of the droplet (reduced through evaporation to 55 μm radius) at 11 tower diameters

  15. Friction characteristics of hardfacing materials in high temperature sodium

    International Nuclear Information System (INIS)

    Mizobuchi, Syotaro; Kano, Shigeki; Nakayama, Kohichi; Atsumo, Hideo

    1980-01-01

    Friction and self-welding test were conducted on several materials used for the contacting and sliding components of a sodium cooled fast breeder reactor. In the present study, the friction and self-welding characteristics of each material were evaluated through measuring the kinetic and breakaway friction coefficients. The influence of oscillating rotation and vertical reciprocating motion on the friction mode was also investigated. The results obtained are as follows: (1) Colmonoy No.6, the nickel base hardfacing alloy, indicated the lowest kinetic friction coefficient of all the materials in the present study. Also, Cr 3 C 2 /Ni-Cr material prepared by a detonation gun showed the most stable friction behavior. (2) The breakaway friction coefficient of each material was dependent upon dwelling time in a sodium environment. (3) The friction behavior of Cr 3 C 2 /Ni-Cr material was obviously related with the finishing roughness of the friction surface. It was anticipated that nichrome material as the binder of the chrome carbide diffused and exuded to the friction surface by sliding in sodium. (4) The friction coefficient in sliding mode of vertical reciprocating was lower than that of oscillating rotation. (author)

  16. The EXIST Mission Concept Study

    Science.gov (United States)

    Fishman, Gerald J.; Grindlay, J.; Hong, J.

    2008-01-01

    EXIST is a mission designed to find and study black holes (BHs) over a wide range of environments and masses, including: 1) BHs accreting from binary companions or dense molecular clouds throughout our Galaxy and the Local Group, 2) supermassive black holes (SMBHs) lying dormant in galaxies that reveal their existence by disrupting passing stars, and 3) SMBHs that are hidden from our view at lower energies due to obscuration by the gas that they accrete. 4) the birth of stellar mass BHs which is accompanied by long cosmic gamma-ray bursts (GRBs) which are seen several times a day and may be associated with the earliest stars to form in the Universe. EXIST will provide an order of magnitude increase in sensitivity and angular resolution as well as greater spectral resolution and bandwidth compared with earlier hard X-ray survey telescopes. With an onboard optical-infra red (IR) telescope, EXIST will measure the spectra and redshifts of GRBs and their utility as cosmological probes of the highest z universe and epoch of reionization. The mission would retain its primary goal of being the Black Hole Finder Probe in the Beyond Einstein Program. However, the new design for EXIST proposed to be studied here represents a significant advance from its previous incarnation as presented to BEPAC. The mission is now less than half the total mass, would be launched on the smallest EELV available (Atlas V-401) for a Medium Class mission, and most importantly includes a two-telescope complement that is ideally suited for the study of both obscured and very distant BHs. EXIST retains its very wide field hard X-ray imaging High Energy Telescope (HET) as the primary instrument, now with improved angular and spectral resolution, and in a more compact payload that allows occasional rapid slews for immediate optical/IR imaging and spectra of GRBs and AGN as well as enhanced hard X-ray spectra and timing with pointed observations. The mission would conduct a 2 year full sky survey in

  17. Predicted carbonation of existing concrete building based on the Indonesian tropical micro-climate

    Science.gov (United States)

    Hilmy, M.; Prabowo, H.

    2018-03-01

    This paper is aimed to predict the carbonation progress based on the previous mathematical model. It shortly explains the nature of carbonation including the processes and effects. Environmental humidity and temperature of the existing concrete building are measured and compared to data from local Meteorological, Climatological, and Geophysical Agency. The data gained are expressed in the form of annual hygrothermal values which will use as the input parameter in carbonation model. The physical properties of the observed building such as its location, dimensions, and structural material used are quantified. These data then utilized as an important input parameter for carbonation coefficients. The relationships between relative humidity and the rate of carbonation established. The results can provide a basis for repair and maintenance of existing concrete buildings and the sake of service life analysis of them.

  18. Applications of seismic damage hazard analysis for the qualification of existing nuclear and offshore facilities

    International Nuclear Information System (INIS)

    Bazzurro, P.; Manfredini, G.M.; Diaz Molina, I.

    1995-01-01

    The Seismic Damage Hazard Analysis (SDHA) is a methodology which couples conventional Seismic Hazard Analysis (SHA) and non-linear response analysis to seismic loadings. This is a powerful tool in the retrofit process: SDHA permits the direct computation of the probability of occurrence of damage and, eventually, collapse of existing and upgraded structural systems. The SDHA methodology is a significant step towards a better understanding and quantification of structural seismic risk. SDHA incorporates and explicitly accounts for seismic load variability, seismic damage potential variability and structural resistance uncertainty. In addition, SDHA makes available a sound strategy to perform non-linear dynamic analyses. A limited number of non-linear dynamic analyses is sufficient to obtain estimates of damage and its probability of occurrence. The basic concepts of the SDHA methodology are briefly reviewed. Illustrative examples are presented, regarding a power house structure, a tubular structure and seabed slope stability problem. (author)

  19. Crowdsourcing step-by-step information extraction to enhance existing how-to videos

    OpenAIRE

    Nguyen, Phu Tran; Weir, Sarah; Guo, Philip J.; Miller, Robert C.; Gajos, Krzysztof Z.; Kim, Ju Ho

    2014-01-01

    Millions of learners today use how-to videos to master new skills in a variety of domains. But browsing such videos is often tedious and inefficient because video player interfaces are not optimized for the unique step-by-step structure of such videos. This research aims to improve the learning experience of existing how-to videos with step-by-step annotations. We first performed a formative study to verify that annotations are actually useful to learners. We created ToolScape, an interac...

  20. Altering existing buildings in the UK

    International Nuclear Information System (INIS)

    Roberts, Simon

    2008-01-01

    The profiles of both existing housing and existing public and commercial buildings show that many have very poor thermal efficiency. The UK housing stock is replaced at a low rate of about 1% a year, so to cut energy use it is essential to address the challenges of existing buildings. This will involve reducing energy demand through passive measures such as retrofitted insulation, replacement of windows and proper airtightness, while ensuring adequate ventilation. Active measures include upgrading improved boilers and adding locally produced energy from wind, biomass, solar power and other sources. The introduction of Display Energy Certificates will increase energy awareness but there will also need to be a programme of increased demolition for the worst-performing homes. In addition, buildings will need to be adapted to cope with worse weather, higher temperatures and increased flood risk as climate change takes effect. Overheating, rather than excessive cold, is set to become a growing problem for householders and employees in existing UK buildings

  1. Vibration-based localisation of structural deterioration in frame-like civil engineering structures

    DEFF Research Database (Denmark)

    Ulriksen, Martin Dalgaard; Damkilde, Lars

    2016-01-01

    With the existing trend of minimising material use in typical frame-like civil engineering structures, such as buildings, bridges, and offshore platforms, these structures will typically be subjected to substantial wind induced vibrations. Besides being a source of disturbance for the occupants...

  2. On the existence of Levi Foliations

    Directory of Open Access Journals (Sweden)

    RENATA N. OSTWALD

    2001-03-01

    Full Text Available Let L be a real 3 dimensional analytic variety. For each regular point p L there exists a unique complex line l p on the space tangent to L at p. When the field of complex line p l p is completely integrable, we say that L is Levi variety. More generally; let L M be a real subvariety in an holomorphic complex variety M. If there exists a real 2 dimensional integrable distribution on L which is invariant by the holomorphic structure J induced by M, we say that L is a Levi variety. We shall prove: Theorem. Let be a Levi foliation and let be the induced holomorphic foliation. Then, admits a Liouvillian first integral. In other words, if is a 3 dimensional analytic foliation such that the induced complex distribution defines an holomorphic foliation ; that is, if is a Levi foliation; then admits a Liouvillian first integral--a function which can be constructed by the composition of rational functions, exponentiation, integration, and algebraic functions (Singer 1992. For example, if f is an holomorphic function and if theta is real a 1-form on ; then the pull-back of theta by f defines a Levi foliation : f*theta = 0 which is tangent to the holomorphic foliation : df = 0. This problem was proposed by D. Cerveau in a meeting (see Fernandez 1997.Seja L Ì uma variedade real de dimensão 3. Para todo ponto regular p Î L existe uma única reta complexa l p no espaço tangente à L em p. Quando o campo de linhas complexas p l p é completamente integrável, dizemos que L é uma variedade de Levi. Mais geralmente, seja L Ì M uma subvariedade real em uma variedade analítica complexa. Se existe uma distribuição real integrável de dimensão 2 em L que é invariante pela estrutura holomorfa J induzida pela variedade complexa M, dizemos que L é uma variedade de Levi. Vamos provar: Teorema. Seja uma folheação de Levi e seja a folheação holomorfa induzida. Então tem integral primeira Liouvilliana. Em outras palavras, se é uma folheação real de

  3. Structural system identification: Structural dynamics model validation

    Energy Technology Data Exchange (ETDEWEB)

    Red-Horse, J.R.

    1997-04-01

    Structural system identification is concerned with the development of systematic procedures and tools for developing predictive analytical models based on a physical structure`s dynamic response characteristics. It is a multidisciplinary process that involves the ability (1) to define high fidelity physics-based analysis models, (2) to acquire accurate test-derived information for physical specimens using diagnostic experiments, (3) to validate the numerical simulation model by reconciling differences that inevitably exist between the analysis model and the experimental data, and (4) to quantify uncertainties in the final system models and subsequent numerical simulations. The goal of this project was to develop structural system identification techniques and software suitable for both research and production applications in code and model validation.

  4. 10 CFR 1040.72 - Existing facilities.

    Science.gov (United States)

    2010-01-01

    ... 10 Energy 4 2010-01-01 2010-01-01 false Existing facilities. 1040.72 Section 1040.72 Energy... § 1040.72 Existing facilities. (a) Accessibility. A recipient shall operate any program or activity to... facilities or every part of a facility accessible to and useable by handicapped persons. (b) Methods. A...

  5. The universal existence of myodural bridge in mammals: an indication of a necessary function.

    Science.gov (United States)

    Zheng, Nan; Yuan, Xiao-Ying; Chi, Yan-Yan; Liu, Pei; Wang, Bing; Sui, Jia-Ying; Han, Seung-Ho; Yu, Sheng-Bo; Sui, Hong-Jin

    2017-08-15

    The "myodural bridge" was described in literatures as a dense fibrous tissue connecting the sub-occipital musculature with the spinal dura mater in human studies. Now the concept of "myodural bridge" was perceived as an exact anatomical structure presumably essential for critical physiological functions in human body, and might exist in other mammals as well. To determine the existence of the "myodural bridge" in other mammals and to lay a foundation for the functional study, we examined representatives in five different mammalian orders. Based on the anatomical dissections, P45 plastinated sections and histological sections, we found that a dense fibrous tissue connected the rectus capitisdorsalis minor and the spinal dura mater through the dorsal atlanto-occipital interspace with or without the medium of the posterior atlanto-occipital membrane. These observed connective tissues were very similar to the "myodural bridge" previously described in humans. We proposed that the "myodural bridge", as an evolutionally conserved structure, presents in many other mammals. Moreover, we believed that the "myodural bridge" might be a homologous organ in mammals. Thus, this study could provide an insight for our understanding the physiological significance of the "myodural bridge", especially in human.

  6. Nonlinear structural damage detection using support vector machines

    Science.gov (United States)

    Xiao, Li; Qu, Wenzhong

    2012-04-01

    An actual structure including connections and interfaces may exist nonlinear. Because of many complicated problems about nonlinear structural health monitoring (SHM), relatively little progress have been made in this aspect. Statistical pattern recognition techniques have been demonstrated to be competitive with other methods when applied to real engineering datasets. When a structure existing 'breathing' cracks that open and close under operational loading may cause a linear structural system to respond to its operational and environmental loads in a nonlinear manner nonlinear. In this paper, a vibration-based structural health monitoring when the structure exists cracks is investigated with autoregressive support vector machine (AR-SVM). Vibration experiments are carried out with a model frame. Time-series data in different cases such as: initial linear structure; linear structure with mass changed; nonlinear structure; nonlinear structure with mass changed are acquired.AR model of acceleration time-series is established, and different kernel function types and corresponding parameters are chosen and compared, which can more accurate, more effectively locate the damage. Different cases damaged states and different damage positions have been recognized successfully. AR-SVM method for the insufficient training samples is proved to be practical and efficient on structure nonlinear damage detection.

  7. Structural Nervous System, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — GTL's SNS technology aids in the operation of new or existing structural health monitoring (SHM) systems by integrating data and power pathways into the structure....

  8. The interplay between rheology and pre-existing structures in the lithosphere and its influence on intraplate tectonics: Insights from scaled physical analogue models.

    Science.gov (United States)

    Santimano, T. N.; Adiban, P.; Pysklywec, R.

    2017-12-01

    The primary controls of deformation in the lithosphere are related to its rheological properties. In addition, recent work reveals that inherited zones of weakness in the deep lithosphere are prevalent and can also define tectonic activity. To understand how deformation is genetically related to rheology and/or pre-existing structures, we compare a set of physical analogue models with the presence and absence of a fault in the deep lithosphere. The layered lithosphere scaled models of a brittle upper crust, viscous lower crust and viscous mantle lithosphere are deformed in a convergent setting. Deformation of the model is recorded using high spatial and temporal stereoscopic cameras. We use Particle Image Velocimetry (PIV) to acquire a time-series dataset and study the velocity field and subsequently strain in the model. The finished model is also cut into cross-section revealing the finite internal structures that are then compared to the topography of the model. Preliminary results show that deformation in models with an inherited fault in the mantle lithosphere is accommodated by displacement along the fault plane that propagates into the overlying viscous lower crust and brittle upper crust. Here, the majority of the deformation is localized along the fault in a brittle manner. This is in contrast to the model absent of a fault that also displays significant amounts of deformation. In this setting, ductile deformation is accommodated by folding and thickening of the viscous layers and flexural shearing of the brittle upper crust. In these preliminary experiments, the difference in the strength profile between the mantle lithosphere and the lower crust is within the same order of magnitude. Future experiments will include models where the strength difference is an order of magnitude. This systematic study aids in understanding the role of rheology and deep structures particularly in transferring stress over time to the surface and is therefore fundamental in

  9. Transcendental idealism and structuralism

    Directory of Open Access Journals (Sweden)

    Ivan Vuković

    2016-02-01

    Full Text Available The author examines possible analogies between Kant’s transcendental idealism and de Saussure’s and Levi-Strauss’s structuralism, in order to analyse if the former can be understood as a predecessor for the later. The author shows that both teachings assume a priori formal framework, but they diverge in the ways they describe it, as well as in understanding of its function. Consequently, the author concludes that structuralism can be seen as one possible use of Kant’s idea about the existence of such a frame. Furthermore, the author claims that Ricker’s understanding of structuralism as ‘Kantianism without transcendental subject’ should be rejected, since a teaching which does not assume existence of such subject cannot be understood as Kantian.

  10. Testing existing software for safety-related applications. Revision 7.1

    International Nuclear Information System (INIS)

    Scott, J.A.; Lawrence, J.D.

    1995-12-01

    The increasing use of commercial off-the-shelf (COTS) software products in digital safety-critical applications is raising concerns about the safety, reliability, and quality of these products. One of the factors involved in addressing these concerns is product testing. A tester's knowledge of the software product will vary, depending on the information available from the product vendor. In some cases, complete source listings, program structures, and other information from the software development may be available. In other cases, only the complete hardware/software package may exist, with the tester having no knowledge of the internal structure of the software. The type of testing that can be used will depend on the information available to the tester. This report describes six different types of testing, which differ in the information used to create the tests, the results that may be obtained, and the limitations of the test types. An Annex contains background information on types of faults encountered in testing, and a Glossary of pertinent terms is also included. This study is pertinent for safety-related software at reactors

  11. Tectonic inheritance in the development of the Kivu - north Tanganyika rift segment of the East African Rift System: role of pre-existing structures of Precambrian to early Palaeozoic origin.

    Science.gov (United States)

    Delvaux, Damien; Fiama Bondo, Silvanos; Ganza Bamulezi, Gloire

    2017-04-01

    The present architecture of the junction between the Kivu rift basin and the north Tanganyika rift basin is that of a typical accommodation zone trough the Ruzizi depression. However, this structure appeared only late in the development of the Western branch of the East African Rift System and is the result of a strong control by pre-existing structures of Precambrian to early Palaeozoic origin. In the frame of a seismic hazard assessment of the Kivu rift region, we (Delvaux et al., 2016) constructed homogeneous geological, structural and neotectonic maps cross the five countries of this region, mapped the pre-rift, early rift and Late Quaternary faults and compiled the existing knowledge on thermal springs (assumed to be diagnostic of current tectonic activity along faults). We also produced also a new catalogue of historical and instrumental seismicity and defined the seismotectonic characteristics (stress field, depth of faulting) using published focal mechanism data. Rifting in this region started at about 11 Ma by initial doming and extensive fissural basaltic volcanism along normal faults sub-parallel to the axis of the future rift valley, as a consequence of the divergence between the Nubia and the Victoria plate. In a later stage, starting around 8-7 Ma, extension localized along a series of major border faults individualizing the subsiding tectonic basins from the uplifting rift shoulders, while lava evolved towards alkali basaltic composition until 2.6 Ma. During this stage, initial Kivu rift valley was extending linearly in a SSW direction, much further than its the actual termination at Bukavu, into the Mwenga-Kamituga graben, up to Namoya. The SW extremity of this graben was linked via a long oblique transfer zone to the central part of Lake Tanganyika, itself reactivating an older ductile-brittle shear zone. In the late Quaternary-early Holocene, volcanism migrated towards the center of the basin, with the development of the Virunga volcanic massif

  12. On the Existence of Evolutionary Learning Equilibriums

    Directory of Open Access Journals (Sweden)

    Masudul Alam Choudhury

    2011-12-01

    Full Text Available The usual kinds of Fixed-Point Theorems formalized on the existence of competitive equilibrium that explain much of economic theory at the core of economics can operate only on bounded and closed sets with convex mappings. But these conditions are hardly true of the real world of economic and financial complexities and perturbations. The category of learning sets explained by continuous fields of interactive, integrative and evolutionary behaviour caused by dynamic preferences at the individual and institutional and social levels cannot maintain the assumption of closed, bounded and convex sets. Thus learning sets and multi-system inter-temporal relations explained by pervasive complementarities and  participation between variables and entities, and evolution by learning, have evolutionary equilibriums. Such a study requires a new methodological approach. This paper formalizes such a methodology for evolutionary equilibriums in learning spaces. It briefly points out the universality of learning equilibriums in all mathematical structures. For a particular case though, the inter-systemic interdependence between sustainable development and ethics and economics in the specific understanding of learning domain is pointed out.

  13. Frequency domain modeling and dynamic characteristics evaluation of existing wind turbine systems

    Science.gov (United States)

    Chiang, Chih-Hung; Yu, Chih-Peng

    2016-04-01

    It is quite well accepted that frequency domain procedures are suitable for the design and dynamic analysis of wind turbine structures, especially for floating offshore wind turbines, since random wind loads and wave induced motions are most likely simulated in the frequency domain. This paper presents specific applications of an effective frequency domain scheme to the linear analysis of wind turbine structures in which a 1-D spectral element was developed based on the axially-loaded member. The solution schemes are summarized for the spectral analyses of the tower, the blades, and the combined system with selected frequency-dependent coupling effect from foundation-structure interactions. Numerical examples demonstrate that the modal frequencies obtained using spectral-element models are in good agreement with those found in the literature. A 5-element mono-pile model results in less than 0.3% deviation from an existing 160-element model. It is preliminarily concluded that the proposed scheme is relatively efficient in performing quick verification for test data obtained from the on-site vibration measurement using the microwave interferometer.

  14. Energy consumptions in existing buildings; Les consommations d'energie des batiments existants

    Energy Technology Data Exchange (ETDEWEB)

    Nuss, St. [Ecole Nationale Superieure des Arts et Industries de Strasbourg, 78 - Saint-Remy-Les-Chevreuse (France)]|[Costic, 78 - Sainte Remy les Chevreuses (France)

    2002-05-01

    This document presents a sectoral analysis of the energy consumptions in existing French buildings: 1) - residential sector: social buildings, private dwellings; 2) - tertiary sector: office buildings, hotels, commercial buildings, school buildings, hospitals; 3) - industry; 4) - general status. (J.S.)

  15. ANALYSIS OF THE CORRELATION BETWEEN THE EXISTING ACCOMMODATION CAPACITY AND THE NUMBER OF TOURISTS ARRIVED IN SUCEAVA COUNTY STRUCTURES OF TOURISTIC RECEPTION

    Directory of Open Access Journals (Sweden)

    Marian ZAHARIA

    2008-06-01

    Full Text Available In the international touristic practice, but also in the specialized literature, it is perceived the population’s trend to spend the leisure time in an active way, by practicing tourism. It is also noted the fact that the forms of tourism organized in the big crowded centers, with fixed, rigid, monotonous programs, with journeys from a crowded environment to another, don’t satisfy anymore the tourists’ aspirations, motivations, options. They prefer the countryside zones that offer a non-polluted environment, with a natural and cultural potential very slightly altered. Such an area, which is inscribed in the rich heritage of the Romanian tourism, is Suceava County, which, by its offer, may be envisaged as an exceptional touristic zone of Romania.  Suceava County, Bârsa Land’s progress demands the inclusion of the principals of the lasting regional development in its development strategy. Within this framework, the importance of studying and analyzing the touristic activity’s evolution can be noted. The need of acknowledging the fluctuations registered by the results of the touristic activity deployment allowed the approach of the issue related to the correlation stage between the existing accommodation capacity and the number of tourists arrived in the accommodation structures of Suceava County during the 2000-2006 period. The mutual involvement relationship, the existence, the direction, the form and the intensity of the connection between the two indicators are analyzed in this paper. The conclusions stated following the analysis of the obtained result, represent an upper step for filling in the image regarding the regional tourism activity in the conditions of the establishment and application of certain regional lasting development strategies.

  16. Evidences for existence of a strange meson with the 1627 MeV/c2 mass

    International Nuclear Information System (INIS)

    Karnaukhov, V.M.; Moroz, V.I.; Coca, C.

    1995-01-01

    The narrow structure with Μ=(1627±4) MeV/c 2 and Γ=(12 -12 +14 ) MeV/c 2 is observable in π - p interactions at 16 GeV/c in 6 effective mass spectra of the Kmπ systems. In the summed spectrum the number of standard deviations in the structure region over the background is 10. A performed compilative analysis of paper results on the study of strange meson resonances in various experiments does not contradict indication for the existence of K(1627)-meson, a narrow enhancement is observed in the same mass region. (author). 21 refs., 4 figs

  17. [Hospital organizational structure].

    Science.gov (United States)

    Bittar, O J

    1994-01-01

    The basic point for an Institution to work is the existence of a definite organizational structure that puts together similar areas allowing decisions and the operationalization of different tasks. Knowledge and analysis of structures of private and public hospitals and a bibliography review about the issue is the purpose of this paper. Suggestions are given about the elaboration of small structures and the utilization of matrix management in order to accomplish the hospitals objectives.

  18. Rehabilitation of existing building structure in expansive soils: A case study in Laghouat, Algeria

    OpenAIRE

    Ouai Aissa

    2017-01-01

    This work presents results obtained from a case study conducted on M’kam neighborhood (600 housing social city) in Laghouat, Algeria. The bloc (J) in this location, suffering from damages that are attributed to the expansive clayey soil interaction with sewage disposal under foundations was the subject of rehabilitation in this study. The principal causes of observed structural damages were studied through diagnostic expertise (inspection-evaluation process) of the cracks and sewage dispo...

  19. Integrated materials–structural models

    DEFF Research Database (Denmark)

    Stang, Henrik; Geiker, Mette Rica

    2008-01-01

    , repair works and strengthening methods for structures. A very significant part of the infrastructure consists of reinforced concrete structures. Even though reinforced concrete structures typically are very competitive, certain concrete structures suffer from various types of degradation. A framework...... should define a framework in which materials research results eventually should fit in and on the other side the materials research should define needs and capabilities in structural modelling. Integrated materials-structural models of a general nature are almost non-existent in the field of cement based...

  20. Organizational Structure and Design in Higher Education: A Literature Review of Organizational Structures in Higher Education with a Focus on the Co-Existence of Academic and Non-Academic Structures.

    Science.gov (United States)

    White, Auston E.

    Two structures of authority coexist in colleges and universities: one that manages the supporting functional services and one that deals with the production areas of scholarship, teaching, and learning. This literature review defines organizational structure, discusses traditional organization models such as bureaucratic models, and outlines the…

  1. Large scale analysis of co-existing post-translational modifications in histone tails reveals global fine structure of cross-talk

    DEFF Research Database (Denmark)

    Schwämmle, Veit; Aspalter, Claudia-Maria; Sidoli, Simone

    2014-01-01

    Mass spectrometry (MS) is a powerful analytical method for the identification and quantification of co-existing post-translational modifications in histone proteins. One of the most important challenges in current chromatin biology is to characterize the relationships between co-existing histone...... sample-specific patterns for the co-frequency of histone post-translational modifications. We implemented a new method to identify positive and negative interplay between pairs of methylation and acetylation marks in proteins. Many of the detected features were conserved between different cell types...... sites but negative cross-talk for distant ones, and for discrete methylation states at Lys-9, Lys-27, and Lys-36 of histone H3, suggesting a more differentiated functional role of methylation beyond the general expectation of enhanced activity at higher methylation states....

  2. A reexamination and extension of international strategy-structure theory

    OpenAIRE

    Wolf, Joachim; Egelhoff, William G.

    2001-01-01

    Using a sample of 95 German firms, the study finds general support for the traditional fits of international strategy-structure theory. Employing an information-processing perspective, the study conceptually and empirically extends existing theory (1) to address strategy-structure fit for various types of matrix structure, and (2) by adding two new elements of international strategy to the existing international strategy-structure model: the level of international transfers and level of forei...

  3. Rebuttal of the existence of solid rare earth bicarbonates and the crystal structure of holmium nitrate pentahydrate

    Energy Technology Data Exchange (ETDEWEB)

    Rincke, Christine; Schmidt, Horst; Voigt, Wolfgang [Institute for Inorganic Chemistry, TU Bergakademie Freiberg (Germany)

    2017-03-16

    The synthesis routes of Gd(HCO{sub 3}){sub 3}.5H{sub 2}O and Ho(HCO{sub 3}){sub 3}.6H{sub 2}O, which are the only known bicarbonates of rare earth metals, were refuted and the published crystal structures were discussed. Because of the structural relationship of Ho(HCO{sub 3}){sub 3}.6H{sub 2}O to rare earth nitrate hexahydrates,[] the synthesis of holmium nitrate hydrate was considered and the crystal structure of Ho(NO{sub 3}){sub 3}.5H{sub 2}O was solved by single crystal X-ray diffraction measurements. Ho(NO{sub 3}){sub 3}.5H{sub 2}O was determined to crystallize in the triclinic space group P1 (no. 2) with a = 6.5680(14) Aa, b = 9.503(2) Aa, c = 10.462(2) Aa, α = 63.739(14) , β = 94.042(2) and γ = 76.000(16) . The crystal structure consists of isolated [Ho(H{sub 2}O){sub 4}(NO{sub 3}){sub 3}] polyhedra and non-coordinating water molecules. It is isotypic to other rare earth nitrate pentahydrates. (copyright 2017 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  4. Does bioethics exist?

    Science.gov (United States)

    Turner, L

    2009-12-01

    Bioethicists disagree over methods, theories, decision-making guides, case analyses and public policies. Thirty years ago, the thinking of many scholars coalesced around a principlist approach to bioethics. That mid-level mode of moral reasoning is now one of many approaches to moral deliberation. Significant variation in contemporary approaches to the study of ethical issues related to medicine, biotechnology and health care raises the question of whether bioethics exists as widely shared method, theory, normative framework or mode of moral reasoning.

  5. Solar potential in existing urban layouts—Critical overview of the existing building stock in Slovenian context

    International Nuclear Information System (INIS)

    Košir, Mitja; Capeluto, Isaac Guedi; Krainer, Aleš; Kristl, Živa

    2014-01-01

    In recent years implementation of sustainable building design in the EU has become one of the key issues in reducing energy dependence. In this context efficient use of solar potential incident on building envelope is essential. The goal of the study is to evaluate the influence of interventions required by the new Slovenian legislation and to propose general site planning guidelines. Special emphasis is devoted to the existing building stock, which is due for refurbishment. The study is carried out on the basis of seven typical urban layouts, which are assessed according to the shape of layout, density, building orientation and design. The calculations are carried out with the program SHADING. The study showed that the existing layouts are not as problematic as had been expected and that form and orientation of buildings present a major challenge. Nevertheless, the quality and the duration of insolation are highly dependent on the specifics of each case. The study showed that by respecting the basic rules of good practice in conjunction with the existing requirements no major changes in the existing design principles are needed. - Highlights: • New Slovenian legislation regarding minimum insolation of building envelope. • Seven typical urban layouts were analysed. • Requirements and rules of good practice result in adequate insolation. • Duration of insolation is highly dependent on the specifics of each case

  6. DNA secondary structures: stability and function of G-quadruplex structures

    Science.gov (United States)

    Bochman, Matthew L.; Paeschke, Katrin; Zakian, Virginia A.

    2013-01-01

    In addition to the canonical double helix, DNA can fold into various other inter- and intramolecular secondary structures. Although many such structures were long thought to be in vitro artefacts, bioinformatics demonstrates that DNA sequences capable of forming these structures are conserved throughout evolution, suggesting the existence of non-B-form DNA in vivo. In addition, genes whose products promote formation or resolution of these structures are found in diverse organisms, and a growing body of work suggests that the resolution of DNA secondary structures is critical for genome integrity. This Review focuses on emerging evidence relating to the characteristics of G-quadruplex structures and the possible influence of such structures on genomic stability and cellular processes, such as transcription. PMID:23032257

  7. Oxidation mechanism of Fe–16Cr alloy as SOFC interconnect in dry/wet air

    International Nuclear Information System (INIS)

    Chen, Zhi-Yuan; Wang, Li-Jun; Li, Fu-Shen; Chou, Kuo-Chih

    2013-01-01

    Highlights: •A special thermodynamic description corresponding to the kinetics was applied. •We reported the relationships of degradation time with temperature and moisture. •”Turning time” in the Fe–16Cr alloy oxidation kinetic model was given. •The oxidation mechanism of Fe–16Cr alloy in the wet air was discussed. -- Abstract: Experimental study on the oxidation corrosions of Fe–16Cr alloy was carried out at 800–1100 °C under dry/wet air conditions. Faster oxidation rate was observed at higher temperature and water vapor content. The degradation time t d between two stages in oxidation process showed an exponential relationship with elevating corrosion temperature in dry air, and a linear relationship with the water content in the case of water vapor introduced to the system. The mechanism of oxidation corrosions of Fe–16Cr alloy was suggested by the Real Physical Picture (RPP) model. It was found that the break-away oxidation in stage II was controlled by diffusion at initial both in dry and wet air, then became linear with the exposure time, which implied that the oxidation rate was then controlled by chemical reaction of the interface between the metal and the oxidized scale. Moreover, the effect of water in the oxidation process is not only to supply more oxygen into system, but also to modify the structures of oxide scale due to the existence of hydrogen atom, which results in the accelerated corrosions

  8. AGE assessment of interactions between climate change policy instruments and pre-existing taxes: the case of Ireland

    NARCIS (Netherlands)

    Wissema, W.W.; Dellink, R.B.

    2010-01-01

    We introduce a computable general equilibrium model for Ireland to investigate the impact of climate policy on the Irish economy, taking special notice of interactions with the existing tax structure. To this end, we extend the model with a detailed representation of the tax system using separate

  9. Decreasing of energy consumption for space heating in existing residential buildings

    International Nuclear Information System (INIS)

    Stamov, S.; Zlateva, M.; Gechkov, N.

    2000-01-01

    An analysis is for the technical possibilities for reducing the energy consumption in existing buildings by means of the heat control and measurement. The basic performances of the heat capacity control methods, of the hierarchy structure of the control and of the heat measurement technologies are presented. This paper also presents the results from the long-term investigation of energy consumption for heating. The results area consist of three typical and uniform buildings in the city of Kazanlak (Bulgaria). The outcome of the investigation provides a valuable basis for future decisions to be made concerning reconstruction of heating installations and enables the results to be transferred. (Authors)

  10. Nuclear accident evacuee bullying and structural violence

    International Nuclear Information System (INIS)

    Tsujiuchi, Takuya

    2018-01-01

    Nuclear accident sufferers should be now referred to as nuclear accident victims. The authors discuss why nuclear accident victims receive not only psychological bullying where no peculiar causes exist, but also corporal and physical bullying and mental suffering, based on the results of questionnaire survey conducted by the authors from January to February 2017, the 'survey on bullying problems related to evacuation from the nuclear accident.' The reasons why the nuclear power evacuation bullying has become a problem at present can be largely classified to the following three categories: (1) opinion that 'bullying' that originally existed just after the nuclear accident became surfaced recently, (2) opinion that latent problems exist as background, and (3) opinion that socially underlying issues are involved in the generation of bullying. Thus, various factors existing under nuclear power evacuation bullying were structurally clarified. In the background of children's nuclear evacuation bullying, adult nuclear power evacuation bullying exists, and there are 'lack of understanding, prejudice, and discrimination against nuclear power and Fukushima' under that. The author thought that 'structural violence' to create the disparity, discrimination, inequality, and injustice of society exists as the basis of such lack of understanding, prejudice, and discrimination, and discussed the 'structural violence' as the basis of bullying. As the upper structure of structural violence associated with nuclear accidents, there are two big phenomena: (1) setting of evacuation/return area not based on reasonable radiation dose standards and (2) fabricated safety and carefreeness myth. The Ministry of Education, Culture, Sports, Science and Technology's report on nuclear bullying could give an impression that 'nuclear power evacuation bullying' is 'not so big problem'. (A.O.)

  11. A coupled chemotaxis-fluid model: Global existence

    KAUST Repository

    Liu, Jian-Guo; Lorz, Alexander

    2011-01-01

    We consider a model arising from biology, consisting of chemotaxis equations coupled to viscous incompressible fluid equations through transport and external forcing. Global existence of solutions to the Cauchy problem is investigated under certain conditions. Precisely, for the chemotaxis-Navier- Stokes system in two space dimensions, we obtain global existence for large data. In three space dimensions, we prove global existence of weak solutions for the chemotaxis-Stokes system with nonlinear diffusion for the cell density.© 2011 Elsevier Masson SAS. All rights reserved.

  12. A coupled chemotaxis-fluid model: Global existence

    KAUST Repository

    Liu, Jian-Guo

    2011-09-01

    We consider a model arising from biology, consisting of chemotaxis equations coupled to viscous incompressible fluid equations through transport and external forcing. Global existence of solutions to the Cauchy problem is investigated under certain conditions. Precisely, for the chemotaxis-Navier- Stokes system in two space dimensions, we obtain global existence for large data. In three space dimensions, we prove global existence of weak solutions for the chemotaxis-Stokes system with nonlinear diffusion for the cell density.© 2011 Elsevier Masson SAS. All rights reserved.

  13. SDSL-ESR-based protein structure characterization

    NARCIS (Netherlands)

    Strancar, J.; Kavalenka, A.A.; Urbancic, I.; Ljubetic, A.; Hemminga, M.A.

    2010-01-01

    As proteins are key molecules in living cells, knowledge about their structure can provide important insights and applications in science, biotechnology, and medicine. However, many protein structures are still a big challenge for existing high-resolution structure-determination methods, as can be

  14. Theorems on Existence and Global Dynamics for the Einstein Equations

    Directory of Open Access Journals (Sweden)

    Rendall Alan

    2002-01-01

    Full Text Available This article is a guide to theorems on existence and global dynamics of solutions ofthe Einstein equations. It draws attention to open questions in the field. The local-in-time Cauchy problem, which is relatively well understood, is surveyed. Global results for solutions with various types of symmetry are discussed. A selection of results from Newtonian theory and special relativity that offer useful comparisons is presented. Treatments of global results in the case of small data and results on constructing spacetimes with prescribed singularity structure are given. A conjectural picture of the asymptotic behaviour of general cosmological solutions of the Einstein equations is built up. Some miscellaneous topics connected with the main theme are collected in a separate section.

  15. Theorems on Existence and Global Dynamics for the Einstein Equations

    Directory of Open Access Journals (Sweden)

    Rendall Alan D.

    2005-10-01

    Full Text Available This article is a guide to theorems on existence and global dynamics of solutions of the Einstein equations. It draws attention to open questions in the field. The local-in-time Cauchy problem, which is relatively well understood, is surveyed. Global results for solutions with various types of symmetry are discussed. A selection of results from Newtonian theory and special relativity that offer useful comparisons is presented. Treatments of global results in the case of small data and results on constructing spacetimes with prescribed singularity structure or late-time asymptotics are given. A conjectural picture of the asymptotic behaviour of general cosmological solutions of the Einstein equations is built up. Some miscellaneous topics connected with the main theme are collected in a separate section.

  16. Existence test for asynchronous interval iterations

    DEFF Research Database (Denmark)

    Madsen, Kaj; Caprani, O.; Stauning, Ole

    1997-01-01

    In the search for regions that contain fixed points ofa real function of several variables, tests based on interval calculationscan be used to establish existence ornon-existence of fixed points in regions that are examined in the course ofthe search. The search can e.g. be performed...... as a synchronous (sequential) interval iteration:In each iteration step all components of the iterate are calculatedbased on the previous iterate. In this case it is straight forward to base simple interval existence and non-existencetests on the calculations done in each step of the iteration. The search can also...... on thecomponentwise calculations done in the course of the iteration. These componentwisetests are useful for parallel implementation of the search, sincethe tests can then be performed local to each processor and only when a test issuccessful do a processor communicate this result to other processors....

  17. The Existence of Public Protection Unit

    Directory of Open Access Journals (Sweden)

    Moh. Ilham A. Hamudy

    2014-12-01

    Full Text Available This article is about the Public Protection Unit (Satlinmas formerly known as civil defence (Hansip. This article is a summary of the results of the desk study and fieldwork conducted in October-November 2013 in the town of Magelang and Surabaya. This study used descriptive qualitative approach to explore the combined role and existence Satlinmas. The results of the study showed, the existence of the problem Satlinmas still leave many, including, first, the legal basis for the establishment of Satlinmas. Until now, there has been no new regulations governing Satlinmas. Existing regulations are too weak and cannot capture the times. Second, the formulation of concepts and basic tasks and functions Satlinmas overlap with other institutions. Third, Satlinmas image in society tend to fade and abused. Fourth, Satlinmas incorporation into the Municipal Police deemed not appropriate, because different philosophy.

  18. Interfacing the existing cask fleet with the MRS

    International Nuclear Information System (INIS)

    Doman, J.W.; Hahn, R.E.

    1992-01-01

    This paper reports that the Department of Energy (DOE) is considering the possibility of using the existing fleet of casks to achieve spent fuel receipt at the Monitored Retrievable Storage (MRS) facility. The existing cask fleet includes the NLI-1/2, the NAC-LWT, the TN-8 (and TN-8L), the TN-9, and the IF-300 casks. Other casks may be available, but their status is not certain. Use of the existing cask fleet at the MRS places additional design requirements on the system, and specifically affects the cask-to-MRS interface. The decision to use the existing cask fleet also places additional demands on training needs and operator certification, and the configuration management system. Some existing cask designs may not be able to mate with a bottom opening hot cell MRS. Use of the existing cask fleet also greatly increases the number of shipments that must be received, to the point that a facility larger than originally envisioned may be required

  19. Are there pre-existing neural, cognitive, or motoric markers for musical ability?

    Science.gov (United States)

    Norton, Andrea; Winner, Ellen; Cronin, Karl; Overy, Katie; Lee, Dennis J; Schlaug, Gottfried

    2005-11-01

    Adult musician's brains show structural enlargements, but it is not known whether these are inborn or a consequence of long-term training. In addition, music training in childhood has been shown to have positive effects on visual-spatial and verbal outcomes. However, it is not known whether pre-existing advantages in these skills are found in children who choose to study a musical instrument nor is it known whether there are pre-existing associations between music and any of these outcome measures that could help explain the training effects. To answer these questions, we compared 5- to 7-year-olds beginning piano or string lessons (n=39) with 5- to 7-year-olds not beginning instrumental training (n=31). All children received a series of tests (visual-spatial, non-verbal reasoning, verbal, motor, and musical) and underwent magnetic resonance imaging. We found no pre-existing neural, cognitive, motor, or musical differences between groups and no correlations (after correction for multiple analyses) between music perceptual skills and any brain or visual-spatial measures. However, correlations were found between music perceptual skills and both non-verbal reasoning and phonemic awareness. Such pre-existing correlations suggest similarities in auditory and visual pattern recognition as well a sharing of the neural substrates for language and music processing, most likely due to innate abilities or implicit learning during early development. This baseline study lays the groundwork for an ongoing longitudinal study addressing the effects of intensive musical training on brain and cognitive development, and making it possible to look retroactively at the brain and cognitive development of those children who emerge showing exceptional musical talent.

  20. Structural response of existing spatial truss roof construction based on Cosserat rod theory

    Science.gov (United States)

    Miśkiewicz, Mikołaj

    2018-04-01

    Paper presents the application of the Cosserat rod theory and newly developed associated finite elements code as the tools that support in the expert-designing engineering practice. Mechanical principles of the 3D spatially curved rods, dynamics (statics) laws, principle of virtual work are discussed. Corresponding FEM approach with interpolation and accumulation techniques of state variables are shown that enable the formulation of the C0 Lagrangian rod elements with 6-degrees of freedom per node. Two test examples are shown proving the correctness and suitability of the proposed formulation. Next, the developed FEM code is applied to assess the structural response of the spatial truss roof of the "Olivia" Sports Arena Gdansk, Poland. The numerical results are compared with load test results. It is shown that the proposed FEM approach yields correct results.

  1. Understanding the structure of data when planning for analysis ...

    African Journals Online (AJOL)

    Human beings and other living creatures tend to exist within organisational structures, such as families, schools, and business organisations. In an educational system, for example, students exist within a hierarchical social structure that can include classroom, grade level, school, school district and country. Data obtained ...

  2. The EcoData retriever: improving access to existing ecological data.

    Directory of Open Access Journals (Sweden)

    Benjamin D Morris

    Full Text Available Ecological research relies increasingly on the use of previously collected data. Use of existing datasets allows questions to be addressed more quickly, more generally, and at larger scales than would otherwise be possible. As a result of large-scale data collection efforts, and an increasing emphasis on data publication by journals and funding agencies, a large and ever-increasing amount of ecological data is now publicly available via the internet. Most ecological datasets do not adhere to any agreed-upon standards in format, data structure or method of access. Some may be broken up across multiple files, stored in compressed archives, and violate basic principles of data structure. As a result acquiring and utilizing available datasets can be a time consuming and error prone process. The EcoData Retriever is an extensible software framework which automates the tasks of discovering, downloading, and reformatting ecological data files for storage in a local data file or relational database. The automation of these tasks saves significant time for researchers and substantially reduces the likelihood of errors resulting from manual data manipulation and unfamiliarity with the complexities of individual datasets.

  3. Kierkegaard e a existência possível

    Directory of Open Access Journals (Sweden)

    Roberto S. Kahlmeyer-Mertens

    2013-05-01

    Full Text Available Resumo: A relação entre a existência e a possibilidade, objeto deste artigo, merece especial atenção quando se trata de Kierkegaard. Isso porque, estes dois conceitos ocupam papéis primordiais na filosofia do autor, constituindo, justamente, o ponto a partir do qual o pensador se distancia criticamente da tradição filosófica. Caracterizar sumariamente os conceitos de existência e possibilidade na filosofia de Kierkegaard, bem como ambientar o filósofo em sua época como um pensador da existência, para além do rótulo de “existencialista”, são nossos presentes objetivos.   Palavras-chave: Kierkegaard, filosofia da existência, existência, possibilidade

  4. Existence and non-existence of solutions for a singular problem with variable potentials

    Directory of Open Access Journals (Sweden)

    Kamel Saoudi

    2017-11-01

    Full Text Available The purpose of this article is to prove some existence and nonexistence theorems for the inhomogeneous singular Dirichlet problem $$ - \\Delta_p u = \\frac{\\lambda k(x}{u^\\delta}\\pm h(x u^q. $$ For proving our results we use the sub and super solution method, and monotonicity arguments.

  5. Hadron structure functions

    International Nuclear Information System (INIS)

    Martin, F.

    1981-03-01

    The x dependence of hadron structure functions is investigated. If quarks can exist in very low mass states (10 MeV for d and u quarks) the pion structure function is predicted to behave like (1-x) and not (1-x) 2 in a x-region around 1. Relativistic and non-relativistic quark bound state pictures of hadrons are considered together with their relation with the Q 2 evolution of structure functions. Good agreement with data is in general obtained

  6. Networked Water Citizen Organisations in Spain: Potential for Transformation of Existing Power Structures in Water Management

    Directory of Open Access Journals (Sweden)

    Nuria Hernández-Mora

    2015-06-01

    Full Text Available The shift from hierarchical-administrative water management toward more transparent, multi-level and participated governance approaches has brought about a shifting geography of players, scales of action, and means of influencing decisions and outcomes. In Spain, where the hydraulic paradigm has dominated since the early 1920s, participation in decisions over water has traditionally been limited to a closed water policy community, made up of economic water users, primarily irrigator associations and hydropower generators, civil engineering corps and large public works companies. The river basin planning process under the Water Framework Directive of the European Union presented a promise of transformation, giving access to non-economic water users, environmental concerns and the wider public to water-related information on planning and decision-making. This process coincided with the consolidation of the use of Information and Communication Technologies (ICTs by the water administration, with the associated potential for information and data generation and dissemination. ICTs are also increasingly used by citizen groups and other interested parties as a way to communicate, network and challenge existing paradigms and official discourses over water, in the broader context of the emergence of 'technopolitics'. This paper investigates if and in what way ICTs may be providing new avenues for participated water resources management and contributing to alter the dominating power balance. We critically analyse several examples where networking possibilities provided by ICTs have enabled the articulation of interest groups and social agents that have, with different degrees of success, questioned the existing hegemonic view over water. The critical review of these cases sheds light on the opportunities and limitations of ICTs, and their relation with traditional modes of social mobilisation in creating new means of societal involvement in water

  7. Existence conditions of optimal trajectories in dynamic control processes; Conditions d'existence de trajectoires optimales des processus dynamiques commandes

    Energy Technology Data Exchange (ETDEWEB)

    Bonnemay-Juricek, L [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1968-07-01

    The existence of solutions in the optimal control problems with free endpoints is studied in this report and existence conditions are established without the usual assumption that the control region is convex. Furthermore the results, in order to be of some utility in physical applications, are expressed only by means of conditions on the parameters defining the system. (author) [French] Ce rapport etudie l'existence de solutions optimales dans les problemes de commande ou le point terminal est libre et ou la duree de l'evolution du systeme a optimiser est connue. Des conditions d'existence y sont formulees sans recourir a l'hypothese usuelle de convexite du domaine des valeurs des commandes. De plus on a cherche a rendre utilisables les resultats en ne faisant porter les conditions que sur les parametres directement accessibles du systeme. (auteur)

  8. Assessment of current Dutch energy transition policy instruments for the existing housing stock

    International Nuclear Information System (INIS)

    Tambach, Milly; Hasselaar, Evert; Itard, Laure

    2010-01-01

    This research assesses to what extent current Dutch energy transition policy instruments for the existing housing stock can fulfil local executive actors' needs and instigate adoption of energy efficiency measures by them. This is done by studying energy policy instruments for the existing housing stock in the Netherlands and in other European countries, and by an empirical research, which analyses barriers and needs of local executive actors. We found that, despite current Dutch energy transition policy instruments for the existing housing stock seem to fulfil local executive actors' needs to a large extent, complementary policy instruments are needed to stimulate and pressure the incumbent renovation regime. A long-term oriented financial rewarding system is needed to build up a structural market for the deployment of renewables, to increase the number of specialist jobs in the building sector, and to stimulate the development of integrated, standardized, building components. Furthermore, a long-term oriented financial rewarding system for energy efficiency investments in housing renovation projects, and a low VAT rate applied to energy efficient renovation measures, are needed. Finally, enforcement possibilities and sanctions (fines) should become an integrative part of Dutch energy certification regulation to make the certificate become part of a value chain.

  9. Ensemble-based prediction of RNA secondary structures.

    Science.gov (United States)

    Aghaeepour, Nima; Hoos, Holger H

    2013-04-24

    Accurate structure prediction methods play an important role for the understanding of RNA function. Energy-based, pseudoknot-free secondary structure prediction is one of the most widely used and versatile approaches, and improved methods for this task have received much attention over the past five years. Despite the impressive progress that as been achieved in this area, existing evaluations of the prediction accuracy achieved by various algorithms do not provide a comprehensive, statistically sound assessment. Furthermore, while there is increasing evidence that no prediction algorithm consistently outperforms all others, no work has been done to exploit the complementary strengths of multiple approaches. In this work, we present two contributions to the area of RNA secondary structure prediction. Firstly, we use state-of-the-art, resampling-based statistical methods together with a previously published and increasingly widely used dataset of high-quality RNA structures to conduct a comprehensive evaluation of existing RNA secondary structure prediction procedures. The results from this evaluation clarify the performance relationship between ten well-known existing energy-based pseudoknot-free RNA secondary structure prediction methods and clearly demonstrate the progress that has been achieved in recent years. Secondly, we introduce AveRNA, a generic and powerful method for combining a set of existing secondary structure prediction procedures into an ensemble-based method that achieves significantly higher prediction accuracies than obtained from any of its component procedures. Our new, ensemble-based method, AveRNA, improves the state of the art for energy-based, pseudoknot-free RNA secondary structure prediction by exploiting the complementary strengths of multiple existing prediction procedures, as demonstrated using a state-of-the-art statistical resampling approach. In addition, AveRNA allows an intuitive and effective control of the trade-off between

  10. Upgrade and Design of Coastal Structures Exposed to Climate Changes

    DEFF Research Database (Denmark)

    Nørgaard, Jørgen Quvang Harck

    This thesis “Upgrade and Design of Coastal Structures Exposed to Climate Changes” evaluates the performance of existing types of structures when exposed to climate changes. This includes also the potential of using cost‐sharing multipurpose structures for protection against the effects of future...... climate changes. The thesis consists of three parts. The first part evaluates the performance of existing design formulae for estimation of wave actions on structures, especially in shallow water since these structures are most vulnerable to the rising sea water levels caused by climate changes. Existing...... of coastal protection structures, which are extended to a wider range of wave conditions, and which can be used to more accurately estimate the influence from climate changes. In the second part of the thesis, the extended and modified formulae are used in case studies to evaluate the influence from climate...

  11. Upgrade and Design of Coastal Structures Exposed to Climate Changes

    DEFF Research Database (Denmark)

    Nørgaard, Jørgen Quvang Harck

    This thesis "Upgrade and Design of Coastal Structures Exposed to Climate Changes" evaluates the performance of existing types of structures when exposed to climate changes. This includes also the potential of using cost‐sharing multipurpose structures for protection against the effects of future...... climate changes. The thesis consists of three parts. The first part evaluates the performance of existing design formulae for estimation of wave actions on structures, especially in shallow water since these structures are most vulnerable to the rising sea water levels caused by climate changes. Existing...... of coastal protection structures, which are extended to a wider range of wave conditions, and which can be used to more accurately estimate the influence from climate changes. In the second part of the thesis, the extended and modified formulae are used in case studies to evaluate the influence from climate...

  12. Collaborative problem structuring using MARVEL

    NARCIS (Netherlands)

    Veldhuis, G.A.; Scheepstal, P.G.M. van; Rouwette, E.A.J.A.; Logtens, T.W.A.

    2015-01-01

    When faced with wicked and messy problems, practitioners can rely on a variety of problem structuring methods (PSMs). Although previous efforts have been made to combine such methods with simulation, currently, few exist that integrate a simulation capability within problem structuring. Our

  13. Oxidation behavior of fuel cladding tube in spent fuel pool accident condition

    International Nuclear Information System (INIS)

    Nemoto, Yoshiyuki; Kaji, Yoshiyuki; Ogawa, Chihiro; Nakashima, Kazuo; Tojo, Masayuki

    2017-01-01

    In spent fuel pool (SFP) under loss-of-cooling or loss-of-coolant severe accident condition, the spent fuels will be exposed to air and heated by their own residual decay heat. Integrity of fuel cladding is crucial for SFP safety therefore study on cladding oxidation in air at high temperature is important. Zircaloy-2 (Zry2) and zircaloy-4 (Zry4) were applied for thermogravimetric analyses (TGA) in different temperatures in air at different flow rates to evaluate oxidation behavior. Oxidation rate increased with testing temperature. In a range of flow rate of air which is predictable in spent fuel lack during a hypothetical SFP accident, influence of flow rate was not clearly observed below 950degC for the Zry2, or below 1050degC for Zry4. In higher temperature, oxidation rate was higher in high rate condition, and this trend was seen clearer when temperature increased. Oxide layers were carefully examined after the TGA analyses and compared with mass gain data to investigate detail of oxidation process in air. It was revealed that the mass gain data in pre-breakaway regime reflects growth of dense oxide film on specimen surface, meanwhile in post-breakaway regime, it reflects growth of porous oxide layer beneath fracture of the dense oxide film. (author)

  14. 30 CFR 75.1708 - Surface structures, fireproofing.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Surface structures, fireproofing. 75.1708... structures, fireproofing. [Statutory Provisions] After March 30, 1970, all structures erected on the surface within 100 feet of any mine opening shall be of fireproof construction. Unless structures existing on or...

  15. Seismic reliability assessment of RC structures including soil–structure interaction using wavelet weighted least squares support vector machine

    International Nuclear Information System (INIS)

    Khatibinia, Mohsen; Javad Fadaee, Mohammad; Salajegheh, Javad; Salajegheh, Eysa

    2013-01-01

    An efficient metamodeling framework in conjunction with the Monte-Carlo Simulation (MCS) is introduced to reduce the computational cost in seismic reliability assessment of existing RC structures. In order to achieve this purpose, the metamodel is designed by combining weighted least squares support vector machine (WLS-SVM) and a wavelet kernel function, called wavelet weighted least squares support vector machine (WWLS-SVM). In this study, the seismic reliability assessment of existing RC structures with consideration of soil–structure interaction (SSI) effects is investigated in accordance with Performance-Based Design (PBD). This study aims to incorporate the acceptable performance levels of PBD into reliability theory for comparing the obtained annual probability of non-performance with the target values for each performance level. The MCS method as the most reliable method is utilized to estimate the annual probability of failure associated with a given performance level in this study. In WWLS-SVM-based MCS, the structural seismic responses are accurately predicted by WWLS-SVM for reducing the computational cost. To show the efficiency and robustness of the proposed metamodel, two RC structures are studied. Numerical results demonstrate the efficiency and computational advantages of the proposed metamodel for the seismic reliability assessment of structures. Furthermore, the consideration of the SSI effects in the seismic reliability assessment of existing RC structures is compared to the fixed base model. It shows which SSI has the significant influence on the seismic reliability assessment of structures.

  16. On the existence of consistent price systems

    DEFF Research Database (Denmark)

    Bayraktar, Erhan; Pakkanen, Mikko S.; Sayit, Hasanjan

    2014-01-01

    We formulate a sufficient condition for the existence of a consistent price system (CPS), which is weaker than the conditional full support condition (CFS). We use the new condition to show the existence of CPSs for certain processes that fail to have the CFS property. In particular this condition...

  17. 36 CFR 327.20 - Unauthorized structures.

    Science.gov (United States)

    2010-07-01

    ... 36 Parks, Forests, and Public Property 3 2010-07-01 2010-07-01 false Unauthorized structures. 327... CHIEF OF ENGINEERS § 327.20 Unauthorized structures. The construction, placement, or existence of any structure (including, but not limited to, roads, trails, signs, non-portable hunting stands or blinds, buoys...

  18. Probabilistic approach to requalification of existing NPPs under aircraft crash loading

    International Nuclear Information System (INIS)

    Birbraer, A.N.; Roleder, A.J.; Shulman, G.S.

    1993-01-01

    A probabilistic approach to the analysis of NPP safety under aircraft impact is discussed. It may be used both for requalification of existing NPPs and in the process of NPP design. NPP is considered as a system of components: structures, pipes, different kinds of equipment, soil, foundation. The exceeding of the limit probability of the radioactive products release out of containment (i.e. of the NPP safety requirements non-fulfilment) is taken as a system failure criterion. An example of an event tree representing the consequence of events causing the failure is given. Described are the methods of estimate of elementary events probabilities through which a composite probability of the failure is evaluated. (author)

  19. Development of mobile platform integrated with existing electronic medical records.

    Science.gov (United States)

    Kim, YoungAh; Kim, Sung Soo; Kang, Simon; Kim, Kyungduk; Kim, Jun

    2014-07-01

    This paper describes a mobile Electronic Medical Record (EMR) platform designed to manage and utilize the existing EMR and mobile application with optimized resources. We structured the mEMR to reuse services of retrieval and storage in mobile app environments that have already proven to have no problem working with EMRs. A new mobile architecture-based mobile solution was developed in four steps: the construction of a server and its architecture; screen layout and storyboard making; screen user interface design and development; and a pilot test and step-by-step deployment. This mobile architecture consists of two parts, the server-side area and the client-side area. In the server-side area, it performs the roles of service management for EMR and documents and for information exchange. Furthermore, it performs menu allocation depending on user permission and automatic clinical document architecture document conversion. Currently, Severance Hospital operates an iOS-compatible mobile solution based on this mobile architecture and provides stable service without additional resources, dealing with dynamic changes of EMR templates. The proposed mobile solution should go hand in hand with the existing EMR system, and it can be a cost-effective solution if a quality EMR system is operated steadily with this solution. Thus, we expect this example to be shared with hospitals that currently plan to deploy mobile solutions.

  20. Structure of Zr-Hf alloys

    International Nuclear Information System (INIS)

    Dobromyslov, A.V.; Taluts, N.I.

    1991-01-01

    Structure of quenched zirconium-hafnium alloy system containing up to 2.5 at. % was studied. Existence of three morphological forms of α-phase was presented: lath, twinned, laminated. Twinning plane in the system was identified. Formation model of packet structure of lath martensite was suggested

  1. Coal handling system structural analysis for modifications or plant life extension

    International Nuclear Information System (INIS)

    Dufault, A.; Weider, F.; Doyle, P.

    1989-01-01

    One neglected aspect of plant modification or life extension is the extent to which previous projects may have affected the integrity of existing structures. During the course of a project to backfit fire protection facilities to existing coal handling systems, it was found that past modifications had added loads to existing coal handling structures which exceeded the available design margin. This paper describes the studies that discovered the original problem areas, as well as the detailed analysis and design considerations used to repair these structures

  2. Essence and Existence in Avicenna and Averroes

    Directory of Open Access Journals (Sweden)

    Belo, Catarina

    2009-12-01

    Full Text Available This article explores the views on existence of medieval Muslim philosophers Avicenna (d. 1037 and Averroes (d. 1198, whose works followed closely the philosophy of Aristotle. In addition to the Aristotelian influence, which permeated all medieval Islamic philosophy, Avicenna and Averroes were also inspired by Islamic theology, known in Arabic as kalām. The distinction between essence and existence is one of the most central and controversial aspects of Avicenna’s philosophy, together with his claim that existence is an accident. Averroes in turn has a radically different conception of existence, identifying it with existing beings rather than considering it as something in itself. With the Latin translation of Avicenna’s metaphysical works in the 12th century, the Avicennian distinction went on to shape much of the debate on existence in medieval Scholastic philosophy and beyond. This article assesses the meaning of the distinction in Avicenna as well as Averroes’ criticism. In explicating their radically different views on existence, it also touches on later discussions concerning existence, for example the issue whether existence is a predicate, in the Modern Age.

    El presente artículo explora las percepciones sobre la existencia de los filósofos medievales musulmanes Avicena (m. 1037 y Averroes (m. 1198, cuyas obras se encuentran muy próximas a la filosofía de Aristóteles. Además de la influencia aristotélica, que caló en toda la filosofía islámica medieval, Avicena y Averroes estuvieron inspirados por la teología islámica, conocida en árabe como Kalām. La distinción entre esencia y existencia es uno de los más fundamentales y controvertidos aspectos de la filosofía de Avicena junto a su aseveración de que la existencia es un accidente. Averroes, en cambio, concibe de forma radicalmente diferente la existencia, identificándola con los seres existentes más que considerarla como algo en

  3. Existence of the Stark-Wannier quantum resonances

    Energy Technology Data Exchange (ETDEWEB)

    Sacchetti, Andrea, E-mail: andrea.sacchetti@unimore.it [Department of Physics, Computer Sciences and Mathematics, University of Modena e Reggio Emilia, Modena (Italy)

    2014-12-15

    In this paper, we prove the existence of the Stark-Wannier quantum resonances for one-dimensional Schrödinger operators with smooth periodic potential and small external homogeneous electric field. Such a result extends the existence result previously obtained in the case of periodic potentials with a finite number of open gaps.

  4. 36 CFR 331.21 - Unauthorized structures.

    Science.gov (United States)

    2010-07-01

    ... 36 Parks, Forests, and Public Property 3 2010-07-01 2010-07-01 false Unauthorized structures. 331... CONSERVATION AREA, KENTUCKY AND INDIANA § 331.21 Unauthorized structures. The construction, placing, or continued existence of any structure of any kind under, upon, in, or over WCA lands or waters is prohibited...

  5. Modelling CEC variations versus structural iron reduction levels in dioctahedral smectites. Existing approaches, new data and model refinements.

    Science.gov (United States)

    Hadi, Jebril; Tournassat, Christophe; Ignatiadis, Ioannis; Greneche, Jean Marc; Charlet, Laurent

    2013-10-01

    A model was developed to describe how the 2:1 layer excess negative charge induced by the reduction of Fe(III) to Fe(II) by sodium dithionite buffered with citrate-bicarbonate is balanced and applied to nontronites. This model is based on new experimental data and extends structural interpretation introduced by a former model [36-38]. The 2:1 layer negative charge increase due to Fe(III) to Fe(II) reduction is balanced by an excess adsorption of cations in the clay interlayers and a specific sorption of H(+) from solution. Prevalence of one compensating mechanism over the other is related to the growing lattice distortion induced by structural Fe(III) reduction. At low reduction levels, cation adsorption dominates and some of the incorporated protons react with structural OH groups, leading to a dehydroxylation of the structure. Starting from a moderate reduction level, other structural changes occur, leading to a reorganisation of the octahedral and tetrahedral lattice: migration or release of cations, intense dehydroxylation and bonding of protons to undersaturated oxygen atoms. Experimental data highlight some particular properties of ferruginous smectites regarding chemical reduction. Contrary to previous assumptions, the negative layer charge of nontronites does not only increase towards a plateau value upon reduction. A peak is observed in the reduction domain. After this peak, the negative layer charge decreases upon extended reduction (>30%). The decrease is so dramatic that the layer charge of highly reduced nontronites can fall below that of its fully oxidised counterpart. Furthermore, the presence of a large amount of tetrahedral Fe seems to promote intense clay structural changes and Fe reducibility. Our newly acquired data clearly show that models currently available in the literature cannot be applied to the whole reduction range of clay structural Fe. Moreover, changes in the model normalising procedure clearly demonstrate that the investigated low

  6. Development and preliminary validation of a leadership competency instrument for existing and emerging allied health professional leaders.

    Science.gov (United States)

    Ang, Hui-Gek; Koh, Jeremy Meng-Yeow; Lee, Jeffrey; Pua, Yong-Hao

    2016-02-19

    No instruments, to our knowledge, exist to assess leadership competency in existing and emerging allied health professional (AHP) leaders. This paper describes the development and preliminary exploration of the psychometric properties of a leadership competency instrument for existing and emerging AHP leaders and examines (i) its factor structure, (ii) its convergent validity with the Leadership Practices Inventory (LPI), and (iii) its discriminative validity in AHPs with different grades. During development, we included 25 items in the AHEAD (Aspiring leaders in Healthcare-Empowering individuals, Achieving excellence, Developing talents) instrument. A cross-sectional study was then conducted in 106 high-potential AHPs from Singapore General Hospital (34 men and 72 women) of different professional grades (49 principal-grade AHPs, 41 senior-grade AHPs, and 16 junior-grade AHPs) who completed both AHEAD and LPI instruments. Exploratory factor analysis was used to test the theoretical structure of AHEAD. Spearman correlation analysis was performed to evaluate the convergent validity of AHEAD with LPI. Using proportional odds regression models, we evaluated the association of grades of AHPs with AHEAD and LPI. To assess discriminative validity, the c-statistics - a measure of discrimination - were derived from these ordinal models. As theorized, factor analysis suggested a two-factor solution, where "skills" and "values" formed separate factors. Internal consistency of AHEAD was excellent (α-values > 0.88). Total and component AHEAD and LPI scores correlated moderately (Spearman ρ-values, 0.37 to 0.58). The c-index for discriminating between AHP grades was higher for AHEAD than for the LPI (0.76 vs. 0.65). The factorial structure of AHEAD was generally supported in our study. AHEAD showed convergent validity with the LPI and outperformed the LPI in terms of discriminative validity. These results provide initial evidence for the use of AHEAD to assess leadership

  7. STRUCTURAL ANALYSIS OF EXISTING ROAD NETWORKS OF ...

    African Journals Online (AJOL)

    Osondu

    2013-01-15

    Jan 15, 2013 ... Social interaction and economic prosperity in ... The impact of technological change in transport sector since the ... among societal, economic, political phenomena through the .... from a point of three miles east of Cooch Behar, and extended ..... perspectives like agriculture, tourism, agro based industries.

  8. Radiation protection programme for existing exposure situation

    International Nuclear Information System (INIS)

    Ramadhani, Hilali Hussein

    2016-04-01

    This study was conducted to develop the Radiation protection Programme (RPP) to ensure that measures are in place for protection of individuals from the existing source of exposure. The study established a number of protective and remedial actions to be considered by the responsible regulatory Authority, licensee for existing exposure in workplace and dwellings. Tanzania is endowed with a number NORMs processing industries with an experience of uncontrolled exploration and extraction of minerals and the use of unsafe mining methods leading to severe environmental damage and appalling living conditions in the mining communities. Some of NORMs industries have been abandoned due to lack of an effect management infrastructure. The residual radioactive materials have been found to be the most import source of existing exposure resulted from NORMs industries. The Radon gas and its progeny have also been found to be a source of existing exposure from natural source as well as the major source of risk and health effects associated with existing exposure situation. The following measures have been discovered to play a pivotal role in avoiding or reducing the source of exposure to individuals such as restriction of the use of the construction materials, restriction on the consumption of foodstuffs and restriction on the access to the land and buildings, the removal of the magnitude of the source in terms of activity concentration as well as improvement of ventilation in dwellings. Therefore, the regulatory body (Tanzania Atomic Energy Commission) should examine the major areas outlined in the established RRP for existing exposure situation resulted from the NORMs industries and natural sources so as to develop strategies that will ensure the adequate protection of members of the public and the environment as well as guiding operating organizations to develop radiation protection and safety measures for workers. (au)

  9. Transportation capabilities of the existing cask fleet

    International Nuclear Information System (INIS)

    Johnson, P.E.; Wankerl, M.W.; Joy, D.S.

    1991-01-01

    This paper describes a number of scenarios estimating the amount of spent nuclear fuel that could be transported to a Monitored Retrievable Storage (MRS) Facility by various combinations of existing cask fleets. To develop the scenarios, the data provided by the Transportation System Data Base (TSDB) were modified to reflect the additional time for cask turnaround resulting from various startup and transportation issues. With these more realistic speed and cask-handling assumptions, the annual transportation capability of a fleet consisting of all of the existing casks is approximately 465 metric tons of uranium (MTU). The most likely fleet of existing casks that would be made available to the DOE consists of two rail, three overweight truck, and six legal weight truck casks. Under the same transportation assumptions, this cask fleet is capable of approximately transporting 270 MTU/year. These ranges of capability is a result of the assumptions pertaining to the number of casks assumed to be available. It should be noted that this assessment assumes additional casks based on existing certifications are not fabricated

  10. Transportation capabilities of the existing cask fleet

    International Nuclear Information System (INIS)

    Johnson, P.E.; Joy, D.S.; Wankerl, M.W.

    1991-01-01

    This paper describes a number of scenarios estimating the amount of spent nuclear fuel that could be transported to a Monitored Retrievable Storage (MRS) Facility by various combinations of existing cask fleets. To develop the scenarios, the data provided by the Transportation System Data Base (TSDB) were modified to reflect the additional time for cask turnaround resulting from various startup and transportation issues. With these more realistic speed and cask-handling assumptions, the annual transportation capability of a fleet consisting of all of the existing casks is approximately 46 metric tons of uranium (MTU). The most likely fleet of existing casks that would be made available to the Department of Energy (DOE) consists of two rail, three overweight truck, and six legal weight truck casks. Under the same transportation assumptions, this cask fleet is capable of approximately transporting 270 MTU/year. These ranges of capability is a result of the assumptions pertaining to the number of casks assumed to be available. It should be noted that this assessment assumes additional casks based on existing certifications are not fabricated. 5 refs., 4 tabs

  11. Existence of a ground state for the confined hydrogen atom in non-relativistic QED

    International Nuclear Information System (INIS)

    Amour, Laurent; Faupin, Jeremy

    2008-01-01

    We consider a system of a hydrogen atom interacting with the quantized electromagnetic field. Instead of fixing the nucleus, we assume that the system is confined by its center of mass. This model is used in theoretical physics to explain the Lamb-Dicke effect. After a brief review of the literature, we explain how to verify some properly chosen binding conditions which lead to the existence of a ground state for our model, and for all values of the fine-structure constant

  12. "What's in a structure?" The story of biguanides

    Science.gov (United States)

    Kathuria, Deepika; Bankar, Apoorva A.; Bharatam, Prasad V.

    2018-01-01

    Biguanides are a very interesting class of molecules which have been extensively studied for their medicinal applications. The structural and electronic structural aspects of biguanides have been explored in detail; however, even today, scientific literature continues to represent biguanides incorrectly as 1a. The X-ray crystal structure analysis and various spectroscopic studies such as UV, 1H and 15N NMR have confirmed that biguanide exists as tautomer 1b. Electronic structure analysis also supports the existence of 1b. This review focuses on the structure and electronic structure of biguanides and aims to emphasize the importance of the correct representation of a structure. There is a need to commence the use of 1b for the general representation of biguanides in textbooks and research articles which will ensure a correct perspective for further studies on these molecules.

  13. Structural Materials: 95. Concrete

    International Nuclear Information System (INIS)

    Naus, Dan J.

    2012-01-01

    Nuclear power plant concrete structures and their materials of construction are described, and their operating experience noted. Aging and environmental factors that can affect the durability of the concrete structures are identified. Basic components of a program to manage aging of these structures are identified and described. Application of structural reliability theory to devise uniform risk-based criteria by which existing facilities can be evaluated to achieve a desired performance level when subjected to uncertain demands and to quantify the effects of degradation is outlined. Finally, several areas are identified where additional research is desired.

  14. Existence conditions of optimal trajectories in dynamic control processes; Conditions d'existence de trajectoires optimales des processus dynamiques commandes

    Energy Technology Data Exchange (ETDEWEB)

    Bonnemay-Juricek, L. [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1968-07-01

    The existence of solutions in the optimal control problems with free endpoints is studied in this report and existence conditions are established without the usual assumption that the control region is convex. Furthermore the results, in order to be of some utility in physical applications, are expressed only by means of conditions on the parameters defining the system. (author) [French] Ce rapport etudie l'existence de solutions optimales dans les problemes de commande ou le point terminal est libre et ou la duree de l'evolution du systeme a optimiser est connue. Des conditions d'existence y sont formulees sans recourir a l'hypothese usuelle de convexite du domaine des valeurs des commandes. De plus on a cherche a rendre utilisables les resultats en ne faisant porter les conditions que sur les parametres directement accessibles du systeme. (auteur)

  15. Coherent structures and dynamical systems

    Science.gov (United States)

    Jimenez, Javier

    1987-01-01

    Any flow of a viscous fluid has a finite number of degrees of freedom, and can therefore be seen as a dynamical system. A coherent structure can be thought of as a lower dimensional manifold in whose neighborhood the dynamical system spends a substantial fraction of its time. If such a manifold exists, and if its dimensionality is substantially lower that that of the full flow, it is conceivable that the flow could be described in terms of the reduced set of degrees of freedom, and that such a description would be simpler than one in which the existence of structure was not recognized. Several examples are briefly summarized.

  16. Financial gap calculations for existing cogeneration 2008

    International Nuclear Information System (INIS)

    Hers, S.J.; Wetzels, W.; Seebregts, A.J.; Van der Welle, A.J.

    2008-05-01

    The Dutch SDE (abbreviation for the renewable energy incentive) subsidy scheme promotes the reduction of CO2 emissions which results from the use of Combined Heat and Power (CHP) plants. This report calculates the profitability of operation of existing CHP plants. This information can be used for decision making on the SDE subsidy for existing CHP plants in 2008 [nl

  17. Structured population dynamics: continuous size and discontinuous stage structures.

    Science.gov (United States)

    Buffoni, Giuseppe; Pasquali, Sara

    2007-04-01

    A nonlinear stochastic model for the dynamics of a population with either a continuous size structure or a discontinuous stage structure is formulated in the Eulerian formalism. It takes into account dispersion effects due to stochastic variability of the development process of the individuals. The discrete equations of the numerical approximation are derived, and an analysis of the existence and stability of the equilibrium states is performed. An application to a copepod population is illustrated; numerical results of Eulerian and Lagrangian models are compared.

  18. Corroded Anchor Structure Stability/Reliability (CAS_Stab-R) Software for Hydraulic Structures

    Science.gov (United States)

    2017-12-01

    Army Engineer Research and Development Center 3909 Halls Ferry Road Vicksburg, MS 39180-6199 Final report Approved for public release...and maintenance of a large inventory of concrete navigation structures. Over the last 40 years, a number of existing Corps hydraulic structures have...ORGANIZATION NAME(S) AND ADDRESS(ES) Information Technology Laboratory U.S. Army Engineer Research and Development Center 3909 Halls Ferry Road

  19. A survey of existing and emerging technologies for external detection of liquid leaks at the Hanford Site

    International Nuclear Information System (INIS)

    Lewis, R.E.; Teel, S.S.

    1994-10-01

    During the history of the Hanford Site, many structures were built that stored and transported liquids used for the production mission; some of these structures are still active. Active structures include underground storage tanks retention basins, and pipes and pipelines. Many of the liquids stored and transported in these structures are potentially hazardous to human health and the environment. Any leakage of liquids from active structures, has the added potential to mobilize contaminants in the unsaturated zone. Therefore, it is beneficial to monitor these structures for leaks. The purpose of tills report is to catalog existing and emerging technologies that have potential for the external monitoring of liquid leaks. The report will focus primarily on the needs at the Hanford Site tank farms that are located in the 200 Areas, but will also be relevant to other Hanford Site facilities. Leak detection systems, both external and internal, are currently used at some Hanford facilities. This report focuses on the detection of leaks as they migrate into the soils surrounding the facilities

  20. A structural informatics approach to mine kinase knowledge bases.

    Science.gov (United States)

    Brooijmans, Natasja; Mobilio, Dominick; Walker, Gary; Nilakantan, Ramaswamy; Denny, Rajiah A; Feyfant, Eric; Diller, David; Bikker, Jack; Humblet, Christine

    2010-03-01

    In this paper, we describe a combination of structural informatics approaches developed to mine data extracted from existing structure knowledge bases (Protein Data Bank and the GVK database) with a focus on kinase ATP-binding site data. In contrast to existing systems that retrieve and analyze protein structures, our techniques are centered on a database of ligand-bound geometries in relation to residues lining the binding site and transparent access to ligand-based SAR data. We illustrate the systems in the context of the Abelson kinase and related inhibitor structures. 2009 Elsevier Ltd. All rights reserved.

  1. On real structures on rigid surfaces

    International Nuclear Information System (INIS)

    Kulikov, Vik S; Kharlamov, V M

    2002-01-01

    We construct examples of rigid surfaces (that is, surfaces whose deformation class consists of a unique surface) with a particular behaviour with respect to real structures. In one example the surface has no real structure. In another it has a unique real structure, which is not maximal with respect to the Smith-Thom inequality. These examples give negative answers to the following problems: the existence of real surfaces in each deformation class of complex surfaces, and the existence of maximal real surfaces in every complex deformation class that contains real surfaces. Moreover, we prove that there are no real surfaces among surfaces of general type with p g =q=0 and K 2 =9. These surfaces also provide new counterexamples to the 'Dif = Def' problem

  2. Complete flexural vibration band gaps in membrane-like lattice structures

    International Nuclear Information System (INIS)

    Yu Dianlong; Liu Yaozong; Qiu Jing; Wang Gang; Zhao Honggang

    2006-01-01

    The propagation of flexural vibration in the periodical membrane-like lattice structure is studied. The band structure calculated with the plane wave expansion method indicates the existence of complete gaps. The frequency response function of a finite periodic structure is simulated with finite element method. Frequency ranges with vibration attenuation are in good agreement with the gaps found in the band structure. Much larger attenuations are found in the complete gaps comparing to those directional ones. The existence of complete flexural vibration gaps in such a lattice structure provides a new idea for vibration control of thin plates

  3. Existence of Projective Planes

    OpenAIRE

    Perrott, Xander

    2016-01-01

    This report gives an overview of the history of finite projective planes and their properties before going on to outline the proof that no projective plane of order 10 exists. The report also investigates the search carried out by MacWilliams, Sloane and Thompson in 1970 [12] and confirms their result by providing independent verification that there is no vector of weight 15 in the code generated by the projective plane of order 10.

  4. 40 CFR 406.34 - Pretreatment standards for existing sources.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 28 2010-07-01 2010-07-01 true Pretreatment standards for existing sources. 406.34 Section 406.34 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED... § 406.34 Pretreatment standards for existing sources. Any existing source subject to this subpart that...

  5. 40 CFR 406.44 - Pretreatment standards for existing sources.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 28 2010-07-01 2010-07-01 true Pretreatment standards for existing sources. 406.44 Section 406.44 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED... § 406.44 Pretreatment standards for existing sources. Any existing source subject to this subpart that...

  6. Experimental evaluation of the structural behaviour of adobe masonry structural elements

    OpenAIRE

    Varum, H.; Costa, A.; Pereira, H.; Almeida, J.; Rodrigues, H.; Silveira, D.

    2007-01-01

    Rehabilitation and strengthening of existing adobe masonry constructions have been neglected during the last decades. In Aveiro, Portugal, many adobe buildings present an important level of structural damage and, in many cases, are even near to ruin, having the majority a high vulnerability to seismic actions. To face the lack of information concerning the mechanical properties and structural behaviour of adobe elements, it was developed an experimental campaign. The composition and mechanica...

  7. TRANSAT-- method for detecting the conserved helices of functional RNA structures, including transient, pseudo-knotted and alternative structures.

    Science.gov (United States)

    Wiebe, Nicholas J P; Meyer, Irmtraud M

    2010-06-24

    The prediction of functional RNA structures has attracted increased interest, as it allows us to study the potential functional roles of many genes. RNA structure prediction methods, however, assume that there is a unique functional RNA structure and also do not predict functional features required for in vivo folding. In order to understand how functional RNA structures form in vivo, we require sophisticated experiments or reliable prediction methods. So far, there exist only a few, experimentally validated transient RNA structures. On the computational side, there exist several computer programs which aim to predict the co-transcriptional folding pathway in vivo, but these make a range of simplifying assumptions and do not capture all features known to influence RNA folding in vivo. We want to investigate if evolutionarily related RNA genes fold in a similar way in vivo. To this end, we have developed a new computational method, Transat, which detects conserved helices of high statistical significance. We introduce the method, present a comprehensive performance evaluation and show that Transat is able to predict the structural features of known reference structures including pseudo-knotted ones as well as those of known alternative structural configurations. Transat can also identify unstructured sub-sequences bound by other molecules and provides evidence for new helices which may define folding pathways, supporting the notion that homologous RNA sequence not only assume a similar reference RNA structure, but also fold similarly. Finally, we show that the structural features predicted by Transat differ from those assuming thermodynamic equilibrium. Unlike the existing methods for predicting folding pathways, our method works in a comparative way. This has the disadvantage of not being able to predict features as function of time, but has the considerable advantage of highlighting conserved features and of not requiring a detailed knowledge of the cellular

  8. Does evaporation paradox exist in China?

    Directory of Open Access Journals (Sweden)

    Z. T. Cong

    2009-03-01

    Full Text Available One expected consequence of global warming is the increase in evaporation. However, lots of observations show that the rate of evaporation from open pans of water has been steadily decreasing all over the world in the past 50 years. The contrast between expectation and observation is called "evaporation paradox". Based on data from 317 weather stations in China from 1956 to 2005, the trends of pan evaporation and air temperature were obtained and evaporation paradox was analyzed. The conclusions include: (1 From 1956 to 2005, pan evaporation paradox existed in China as a whole while pan evaporation kept decreasing and air temperature became warmer and warmer, but it does not apply to Northeast and Southeast China; (2 From 1956 to 1985, pan evaporation paradox existed narrowly as a whole with unobvious climate warming trend, but it does not apply to Northeast China; (3 From 1986 to 2005, in the past 20 years, pan evaporation paradox did not exist for the whole period while pan evaporation kept increasing, although it existed in South China. Furthermore, the trend of other weather factors including sunshine duration, windspeed, humidity and vapor pressure deficit, and their relations with pan evaporation are discussed. As a result, it can be concluded that pan evaporation decreasing is caused by the decreasing in radiation and wind speed before 1985 and pan evaporation increasing is caused by the decreasing in vapor pressure deficit due to strong warming after 1986. With the Budyko curve, it can be concluded that the actual evaporation decreased in the former 30 years and increased in the latter 20 year for the whole China.

  9. A Layer Framework to Investigate Student Understanding and Application of the Existence and Uniqueness Theorems of Differential Equations

    Science.gov (United States)

    Raychaudhuri, D.

    2007-01-01

    The focus of this paper is on student interpretation and usage of the existence and uniqueness theorems for first-order ordinary differential equations. The inherent structure of the theorems is made explicit by the introduction of a framework of layers concepts-conditions-connectives-conclusions, and we discuss the manners in which students'…

  10. Topology of RNA-RNA interaction structures

    DEFF Research Database (Denmark)

    Andersen, Jørgen Ellegaard; Huang, Fenix Wenda; Penner, Robert

    2012-01-01

    Abstract The topological filtration of interacting RNA complexes is studied, and the role is analyzed of certain diagrams called irreducible shadows, which form suitable building blocks for more general structures. We prove that, for two interacting RNAs, called interaction structures, there exist...

  11. Structural realism beyond physics.

    Science.gov (United States)

    Tulodziecki, Dana

    2016-10-01

    The main purpose of this paper is to test structural realism against (one example from) the historical record. I begin by laying out an existing challenge to structural realism - that of providing an example of a theory exhibiting successful structures that were abandoned - and show that this challenge can be met by the miasma theory of disease. However, rather than concluding that this is an outright counterexample to structural realism, I use this case to show why it is that structural realism, in its current form, has trouble dealing with theories outside physics. I end by making some concrete suggestions for structural realists to pursue if, indeed, they are serious about extending structural realism to other domains. Copyright © 2016 Elsevier Ltd. All rights reserved.

  12. Nonuniform nuclear structures and QPOs in giant flares

    International Nuclear Information System (INIS)

    Sotani, Hajime

    2012-01-01

    We show that the shear modes in the neutron star crust are quite sensitive to the existence of nonuniform nuclear structures, the so-called “pasta”. Due to the existence of pasta phase, the frequencies of shear modes are reduced. Since the torsional shear frequencies depend strongly on the structure of pasta phase, through the observations of stellar oscillations, one can probe the pasta structure in the crust. Additionally, considering the effect of pasta phase, we show the possibility to explain all the observed frequencies in the SGR 1806-20 with using only crust torsional oscillations.

  13. Nonuniform nuclear structures and QPOs in giant flares

    Energy Technology Data Exchange (ETDEWEB)

    Sotani, Hajime [Division of Theoretical Astronomy, National Astronomical Observatory of Japan, 2-21-1 Osawa, Mitaka, Tokyo 181-8588 (Japan)

    2012-11-12

    We show that the shear modes in the neutron star crust are quite sensitive to the existence of nonuniform nuclear structures, the so-called 'pasta'. Due to the existence of pasta phase, the frequencies of shear modes are reduced. Since the torsional shear frequencies depend strongly on the structure of pasta phase, through the observations of stellar oscillations, one can probe the pasta structure in the crust. Additionally, considering the effect of pasta phase, we show the possibility to explain all the observed frequencies in the SGR 1806-20 with using only crust torsional oscillations.

  14. Do ‘African’ universities exist?

    DEFF Research Database (Denmark)

    Jensen, Stig; Adriansen, Hanne Kirstine; Madsen, Lene Møller

    2015-01-01

    This chapter provides a background for understanding the book. We outline some of the debates in which the individual chapters are situated and thereby show how the book contributes to and fills gaps in existing research. After providing a short history of African universities, the chapter subseq...

  15. Limitations of existing web services

    Indian Academy of Sciences (India)

    First page Back Continue Last page Overview Graphics. Limitations of existing web services. Uploading or downloading large data. Serving too many user from single source. Difficult to provide computer intensive job. Depend on internet and its bandwidth. Security of data in transition. Maintain confidentiality of data ...

  16. Strengthening, modification and repair techniques’ prioritization for structural integrity control of ageing offshore structures

    International Nuclear Information System (INIS)

    Samarakoon, Samindi M.K.; Ratnayake, R.M. Chandima

    2015-01-01

    Structural integrity control is vital for existing ageing as well as newly built offshore and onshore structures. Structural integrity control becomes highly sensitive to interventions under a potential loss of structural integrity when it comes to offshore oil and gas production and process facilities. This is mainly due to the inherent constraints present in carrying out engineering work in the offshore atmosphere. It has been further exacerbated by the ageing offshore structures and the necessity of carrying out life extension toward the end of their design service lives. Local and international regulations demand the implementation of appropriate strengthening, modification and repair plans when significant changes in the structural integrity are revealed. In this context, strengthening, modification and repair techniques such as welding, member removal/reduction of loading, mechanical clamping and grouted repairs play a vital role. This manuscript presents an approach for prioritizing the strengthening, modification and repair techniques using a multi-criteria analysis approach. An analytic hierarchy process has been selected for the analysis via an illustrative case. It also provides a comprehensive overview of currently existing; strengthening, modification and repair techniques and their comparative pros and cons. - Highlights: • Structural integrity control (SIC) of ageing and intact offshore structures. • Strengthening, modification and/or repair (SMR) techniques have been explained. • Application of multi-criteria analysis conserving SI has been illustrated. • SMR techniques prioritization and sensitivity analysis has been performed

  17. Comparative Analysis of Existing RC Columns Jacketed with CFRP or FRCC

    Directory of Open Access Journals (Sweden)

    Marta Del Zoppo

    2018-03-01

    Full Text Available Reinforced concrete (RC columns typical of existing structures often exhibit premature failures during seismic events (i.e., longitudinal bars buckling and shear interaction mechanisms due to the poor quality concrete and the absence of proper seismic details in the potential plastic hinge region. The Fiber Reinforced Polymers (FRP externally bonded reinforcement is known to be a valid technique to improve the shear capacity or the ductility of existing RC columns. However, few experimental tests have proven its effectiveness in the case of columns affected by shear interaction mechanisms. In this work, the behavior of existing RC columns with border line behavior between flexure and shear have been investigated in the case of poor quality concrete and light FRP strengthening with local jacketing and medium quality concrete and strong FRP strengthening with local jacketing, in order to highlight the effect of concrete strength on the effectiveness of the retrofit intervention. As an alternative to FRP jacketing; the effectiveness of the Fiber Reinforced Cementitious Composite (FRCC jacketing for the seismic strengthening of columns with highly deteriorated concrete cover or columns already damaged by an earthquake is also evaluated. Six full-scale RC columns have been tested under cyclic loading: one was used as a control specimen; four were strengthened in the potential plastic hinge region with carbon FRP (CFRP; and one was fully jacketed with FRCC. The comparison between poor and medium quality concrete columns showed that the CFRP local jacketing is more effective in the case of poor quality concrete. The FRCC jacketing appears to be a sound repair strategy and a suitable alternative to the FRP jacketing in case of poor quality; however, more experimental research is needed for improving this retrofit technique.

  18. Testing Cadmium-Free Coatings

    Science.gov (United States)

    2011-08-30

    Secretary of Defense Directive • “Approve the use of alternatives [to hexavalent chromium (Cr6+)] where they can perform adequately for the intended...Effect of corrosion on breakaway torque 12 OPSEC approved for public release Fastener Finish Study FINISH POST-TREATMENT LUBRICANT Cadmium Hexavalent ...Past Testing Electrical Connectors Coatings Al / TCP ZnNi / TCP ZnNi / Non- Chrome Passivation (NCP) Ni-PTFE 1 Ni-PTFE 2 Note: SnZn tested on flat

  19. Existence of solutions of nonlinear integrodifferential equations of ...

    Indian Academy of Sciences (India)

    The results are obtained by using semigroup theory and the Schauder fixed point ... The problem of existence of solutions of evolution equations with nonlocal ... we assume that there exists an operator E on DЕEЖИX given by the formula.

  20. Organizational structure in process-based organizations

    NARCIS (Netherlands)

    Vanhaverbeke, W.P.M.; Torremans, H.P.M.

    1999-01-01

    This paper investigates the role of the organization structure in process-based organizations. We argue that companies cannot be designed upon organizational processes only or that process management can be simply imposed as an additional structural dimension on top of the existing functional or

  1. Oxidation behaviour of titanium in high temperature steam

    Energy Technology Data Exchange (ETDEWEB)

    Moroishi, T; Shida, Y [Sumitomo Metal Industries Ltd., Amagasaki, Hyogo (Japan). Central Research Labs.

    1978-03-01

    The oxidation of pure titanium was studied in superheated steam at 400 -- 550/sup 0/C. The effects of prior cold working and several heat treatment conditions on the oxidation were examined and also the effects of the addition of small amounts of iron and oxygen were investigated. The oxidation mechanism of pure titanium is discussed in relation to the scale structure and the oxidation kinetics. Hydrogen absorption rate was also measured. As a result, the following conclusions were drawn: (1) The oxidation of pure titanium in steam was faster than in air and breakaway oxidation was observed above 500/sup 0/C after the specimen had gained a certain weight. Prior cold working and heat treatment conditions scarcely affected the oxidation rate, whereas the specimen containing small amounts of iron and oxygen showed a little more rapid oxidation. (2) At 500 and 550/sup 0/C a dark grey inner scale and a yellow-brown outer scale were formed. The outer scale was apt to exfoliate after the occurrence of breakaway oxidation. At 400 and 450/sup 0/C only a dark grey scale was observed. All of these oxides were identified as the rutile type, TiO/sub 2/. Furthermore, the presence of a thin and uniform oxygen rich layer beneath the external scale was confirmed at all test temperatures. (3) The measured weight gain approximately followed the cubic rate law; this would be expected for the following reason; one component of the weight gain is due to the dissolved oxygen, the amount of which remains constant after the early stages of oxidation. The second component is due to the parabolic growth of the external TiO/sub 2/ scale. When these contributions are added a pseudo-cubic weight gain curve results. (4) It was shown that 50 percent of the hydrogen generated during the oxidation was absorbed into the metal.

  2. Existence of pareto equilibria for multiobjective games without compactness

    OpenAIRE

    Shiraishi, Yuya; Kuroiwa, Daishi

    2013-01-01

    In this paper, we investigate the existence of Pareto and weak Pareto equilibria for multiobjective games without compactness. By employing an existence theorem of Pareto equilibria due to Yu and Yuan([10]), several existence theorems of Pareto and weak Pareto equilibria for the multiobjective games are established in a similar way to Flores-B´azan.

  3. Analysis of Existing Guidelines for the Systematic Planning Process of Clinical Registries.

    Science.gov (United States)

    Löpprich, Martin; Knaup, Petra

    2016-01-01

    Clinical registries are a powerful method to observe the clinical practice and natural disease history. In contrast to clinical trials, where guidelines and standardized methods exist and are mandatory, only a few initiatives have published methodological guidelines for clinical registries. The objective of this paper was to review these guidelines and systematically assess their completeness, usability and feasibility according to a SWOT analysis. The results show that each guideline has its own strengths and weaknesses. While one supports the systematic planning process, the other discusses clinical registries in great detail. However, the feasibility was mostly limited and the special requirements of clinical registries, their flexible, expandable and adaptable technological structure was not addressed consistently.

  4. On real structures on rigid surfaces

    Energy Technology Data Exchange (ETDEWEB)

    Kulikov, Vik S [Steklov Mathematical Institute, Russian Academy of Sciences (Russian Federation); Kharlamov, V M [Institut de Recherche Matematique Avanee Universite Louis Pasteur et CNRS 7 rue Rene Descartes (France)

    2002-02-28

    We construct examples of rigid surfaces (that is, surfaces whose deformation class consists of a unique surface) with a particular behaviour with respect to real structures. In one example the surface has no real structure. In another it has a unique real structure, which is not maximal with respect to the Smith-Thom inequality. These examples give negative answers to the following problems: the existence of real surfaces in each deformation class of complex surfaces, and the existence of maximal real surfaces in every complex deformation class that contains real surfaces. Moreover, we prove that there are no real surfaces among surfaces of general type with p{sub g}=q=0 and K{sup 2}=9. These surfaces also provide new counterexamples to the 'Dif = Def' problem.

  5. Performance of Existing Hydrogen Stations

    Energy Technology Data Exchange (ETDEWEB)

    Sprik, Samuel [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Kurtz, Jennifer M [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Ainscough, Christopher D [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Saur, Genevieve [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Peters, Michael C [National Renewable Energy Laboratory (NREL), Golden, CO (United States)

    2017-12-01

    In this presentation, the National Renewable Energy Laboratory presented aggregated analysis results on the performance of existing hydrogen stations, including performance, operation, utilization, maintenance, safety, hydrogen quality, and cost. The U.S. Department of Energy funds technology validation work at NREL through its National Fuel Cell Technology Evaluation Center (NFCTEC).

  6. On the Edge of Existence: Malian Migrants in the Maghreb

    Directory of Open Access Journals (Sweden)

    Line Richter

    2016-04-01

    Full Text Available Based on ethnographic fieldwork among Malian migrants and migration brokers in Mali, Algeria, Morocco, and France, this article investigates life in exile on the edge of Europe. Zooming in on the experiences of interlocutors in Morocco and Algeria, the article will explore the experiential dimensions of living in an extended liminal-ity. Anthropologically, life in so-called places of transit, such as the Maghreb countries, has often been dealt with through the lens of liminality. In this article my aim is to build on the insights from such endeavors, and reorient the focus by illumi-nating what this specific type of permanent liminality entails. I posit that a more suitable term to call this is 'limbo'. This, I argue, consists of three main features. First, the motivation for leaving Mali is for most migrants embedded in the lack of opportunities for social mobility: the Malian youth who end up leaving, are in Honwana's words, stuck in 'waithood' at home, in what many argue is a liminal social position. Second, social and political structures are not absent in the Maghreb, rather they are quite discernable and can be seen as continuations and mim-icking of existing structures. Third, experiences of dramatic ruptures with humanity and morality are key characteristics of life on the edge of Europe.

  7. 40 CFR 63.312 - Existing regulations and requirements.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 9 2010-07-01 2010-07-01 false Existing regulations and requirements. 63.312 Section 63.312 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... National Emission Standards for Coke Oven Batteries § 63.312 Existing regulations and requirements. (a) The...

  8. Existence and consequences of Coulomb pairing of electrons in a solid

    International Nuclear Information System (INIS)

    Mahajan, S.M.; Thyagaraja, A.

    1996-11-01

    It is shown from first principles that, in the periodic potential of a crystalline solid, short-range (i.e., screened) binary Coulomb interactions can lead to a two-electron bound state. It is further suggested that these composite bosonic states (charge -2e, and typically spin zero) could mediate an effectively attractive interaction between pairs of conduction electrons close to the Fermi level. This necessarily short range attractive interaction, which is crucially dependent on the band structure of the solid, and is complementary to the phonon-mediated one, may provide a source for the existence and properties of short correlation-length electron pairs (analogous to but distinct from Cooper pairs) needed to understand high temperature superconductivity. Several distinctive and observable characteristics of the proposed pairing scheme are discussed

  9. Evolution PDEs with nonstandard growth conditions existence, uniqueness, localization, blow-up

    CERN Document Server

    Antontsev, Stanislav

    2015-01-01

    This monograph offers the reader a treatment of the theory of evolution PDEs with nonstandard growth conditions. This class includes parabolic and hyperbolic equations with variable or anisotropic nonlinear structure. We develop methods for the study of such equations and present a detailed account of recent results. An overview of other approaches to the study of PDEs of this kind is provided. The presentation is focused on the issues of existence and uniqueness of solutions in appropriate function spaces, and on the study of the specific qualitative properties of solutions, such as localization in space and time, extinction in a finite time and blow-up, or nonexistence of global in time solutions. Special attention is paid to the study of the properties intrinsic to solutions of equations with nonstandard growth.

  10. Existing contradictions and problems in China's current economic and social development

    Institute of Scientific and Technical Information of China (English)

    Wang Tongsan

    2014-01-01

    Since the 18th National Congress of Communist Party of China (CPC),China has made important achievements and headway in economic and social development.However,now more than ever the focus should be on the conflicts and problems that continue to exist in China's economy.This paper examines six of them:(1) lack of a firm foundation for sustaining steady economic growth;(2) risks and hidden dangers in the financial,banking,and real estate sectors and massive overcapacity in some industries;(3) increasing difficulty in increasing agricultural production and raising rural incomes;(4) severe air,water,and soil pollution in certain regions and the arduous task of energy conservation and emissions reduction;(5) major structural problems constraining employment;and (6) issues of people's livelihood that have been the source of dissatisfaction for many Chinese citizens.

  11. Co-existence of two plasma phases in solar and AGN coronas

    Directory of Open Access Journals (Sweden)

    Kubičela A.

    1998-01-01

    Full Text Available Here we have juxtaposed two distant cosmic locations of the Sun and AGN where neutral hydrogen appears in a close connection with hot coronas. Besides the solar photosphere, chromosphere and prominences where the presence of neutral hydrogen is well established, its emission quite high in hot solar corona is still puzzling. Some of earlier observations where Hα emission in solar corona was detected in eclipse and in daily coronagraphic observations are reviewed. A proper theoretical explanation of this cold chromospheric-type emission in the hot corona does not exist yet. On the other side, a similar emission of hydrogen lines is present in Active Galactic Nuclei (AGNs. Much research work is currently being done in this field. We outline some of the concepts of the AGN structure prevailing in the astrophysics today.

  12. The conditions of existence of first integrals and Hamiltonian structures of Lotka-Volterra and Volterra systems

    International Nuclear Information System (INIS)

    Dubovik, V.M.; Galperin, A.G.; Richvitsky, V.S.; Slepnyov, S.K.

    2000-01-01

    A study of a certain subset of Volterra equations has revealed that some statements about time-independent constants of motion, Hamiltonian functions, and Poisson structure matrices appearing in the Lotka-Volterra equations, either regarded as proven or of the sort that could be proven, are not valid, in fact. Particular cases are given as examples to explain the reasons for the occurring phenomena

  13. The global existence problem in general relativity

    CERN Document Server

    Andersson, L

    2000-01-01

    We survey some known facts and open questions concerning the global properties of 3+1 dimensional space--times containing a compact Cauchy surface. We consider space--times with an $\\ell$--dimensional Lie algebra of space--like Killing fields. For each $\\ell \\leq 3$, we give some basic results and conjectures on global existence and cosmic censorship. For the case of the 3+1 dimensional Einstein equations without symmetries, a new small data global existence result is announced.

  14. SPATIAL STRUCTURE OF WATERFRONT CITIES: COMPARISSON BETWEEN KENDARI AND MANADO

    Directory of Open Access Journals (Sweden)

    Slamet Trisutomo

    2016-01-01

    Full Text Available As an archipelagic country, many cities in Indonesia exist and grow at the waterfronts. This research aims to explore comparatively the spatial structure of two waterfront cities: Kendari represents a bay-front with U-form coast line, and Manado as a sea-front with straight line coast line. The spatial structures are represented by spatial pattern, land use pattern, population density, road network, BCR and urban hierarchy. Data were collected through field survey, reading government documents and doing in-depth interview of some key informants. Descriptive and comparative analyses - both similarities and differences - on spatial structures were focused on the relationships between spatial structures with the existence of the waterfronts. The findings show that at the early period of growth, spatial structures of both cities were formed by the existence of the waterfront similarly. Influenced by physical development such as commercial facilities and housing settlements, the spatial structure recently spreads out to the mainland area created some new sub-centers. Understanding the character of spatial structures will be significant for directing and controlling the urban land use to create a sustainable waterfront city.

  15. Temperature-dependent structure evolution in liquid gallium

    International Nuclear Information System (INIS)

    Xiong, L.H.; Wang, X.D.; Yu, Q.; Zhang, H.; Zhang, F.; Sun, Y.; Cao, Q.P.; Xie, H.L.; Xiao, T.Q.; Zhang, D.X.; Wang, C.Z.; Ho, K.M.

    2017-01-01

    Temperature-dependent atomistic structure evolution of liquid gallium (Ga) has been investigated by using in situ high energy X-ray diffraction experiment and ab initio molecular dynamics simulation. Both experimental and theoretical results reveal the existence of a liquid structural change around 1000 K in liquid Ga. Below and above this temperature the liquid exhibits differences in activation energy for self-diffusion, temperature-dependent heat capacity, coordination numbers, density, viscosity, electric resistivity and thermoelectric power, which are reflected from structural changes of the bond-orientational order parameter Q_6, fraction of covalent dimers, averaged string length and local atomic packing. This finding will trigger more studies on the liquid-to-liquid crossover in metallic melts. - Graphical abstract: Atomistic structure evolution of liquid gallium has been investigated by using in situ high energy X-ray diffraction and ab initio molecular dynamics simulations, which both demonstrate the existence of a liquid structural change together with reported density, viscosity, electric resistivity and absolute thermoelectric power data.

  16. Mantle transition zone structure beneath the Canadian Shield

    Science.gov (United States)

    Thompson, D. A.; Helffrich, G. R.; Bastow, I. D.; Kendall, J. M.; Wookey, J.; Eaton, D. W.; Snyder, D. B.

    2010-12-01

    The Canadian Shield is underlain by one of the deepest and most laterally extensive continental roots on the planet. Seismological constraints on the mantle structure beneath the region are presently lacking due to the paucity of stations in this remote area. Presented here is a receiver function study on transition zone structure using data from recently deployed seismic networks from the Hudson Bay region. High resolution images based on high signal-to-noise ratio data show clear arrivals from the 410 km and 660 km discontinuities, revealing remarkably little variation in transition zone structure. Transition zone thickness is close to the global average (averaging 245 km across the study area), and any deviations in Pds arrival time from reference Earth models can be readily explained by upper-mantle velocity structure. The 520 km discontinuity is not a ubiquitous feature, and is only weakly observed in localised areas. These results imply that the Laurentian root is likely confined to the upper-mantle and if any mantle downwelling exists, possibly explaining the existence of Hudson Bay, it is also confined to the upper 400 km. Any thermal perturbations at transition zone depths associated with the existence of the root, whether they be cold downwellings or elevated temperatures due to the insulating effect of the root, are thus either non-existent or below the resolution of the study.

  17. Neural Network for Optimization of Existing Control Systems

    DEFF Research Database (Denmark)

    Madsen, Per Printz

    1995-01-01

    The purpose of this paper is to develop methods to use Neural Network based Controllers (NNC) as an optimization tool for existing control systems.......The purpose of this paper is to develop methods to use Neural Network based Controllers (NNC) as an optimization tool for existing control systems....

  18. Existing knowledge related to mainstreaming IKS into Educational ...

    African Journals Online (AJOL)

    The study aimed at determining existing knowledge related to mainstreaming of IKS into education system. The qualitative research methodology was appropriate for this study to explore and describe the mainstreaming of IKS into the existing education system. The study included 10 school teachers (5male and 5 females) ...

  19. Musical information processing reflecting its structure

    OpenAIRE

    Hiraga, Rumi

    1999-01-01

    In pursuit of generating expressive musical rendition with rules, the computer music project Psyche has greatly concerned musical structure. Although described implicitly, musical structure exists innately and absolutely in musical scores. This thesis demonstrates the successful introduction of musical structure to computer music systems that are related to performance synthesis. Two systems, a performance visualization system and a computer-assisted musical analysis system Daphne, are descri...

  20. Self-weldability of various materials in high temperature sodium

    International Nuclear Information System (INIS)

    Mizobuchi, Syotaro; Kano, Shigeki; Nakayama, Kohichi; Atsumo, Hideo

    1980-01-01

    Self-Weldability of Various Materials in High Temperature Sodium. The self-welding behavior of various materials was evaluated by measuring the tensile breakaway force of the specimen which had been self-welded in high temperature sodium. Experiments were carried out to investigate the influence of the sodium temperature and the contact stress on the self-welding behavior. The results obtained are as follows: (1) The self-welding behavior in sodium was recognized to initiate by the diffusion of the principal element through the real contact area. (2) Remarkable self-welding behavior was observed for SUS 316 material at 650 0 C, and for 2 1/4Cr-1Mo steel at a sodium temperature of 600 0 C. The self-welding force acting on the real contact area corresponds to the tensile strength of each material. (3) Hard chrome plating or hardfacing material showed good self-weld resistance, but the different combinations of SUS 316 with either of these materials were observed to easily cause self-welding. (4) The self-weldability of Cr 3 C 2 /Ni-Cr material varied with the preparing methods, especially, with the distribution of the binder composition contained in this material. (5) A derived equation was proposed to evaluate the self-welding force. It was found that the measured breakaway force was relatively equal to the self-welding force derived from this equation. (author)

  1. The Existence of Overall Satisfaction in Service Customer Relationships

    Directory of Open Access Journals (Sweden)

    Zulganef Zulganef

    2006-09-01

    Full Text Available Garbarino and Johnson (1999 find that there is no correlation between overall satisfaction and loyalty in the field of customer relationship. Their finding indicates that satisfaction is no longer an important issue in managing service organizations. This research investigates the existence of satisfaction in service organizations, which have relationships with customers. Contrary to Garbarino and Johnson’s (1999 finding, this research finds that overall satisfaction, through commitment, has a relationship with loyalty. Hence, customer satisfaction is still a main issue with respect to managing service organizations, especially service organizations that have customer-relationship strategy. Survey method was conducted to test 12 hypotheses, and the sample of this research is customers of credit cardholders and supermarket cardholders. Sample size is 382 consisting of 196 (51.3% credit cardholders and 186 (48.7% supermarket cardholders. Data were analyzed using two-step structural equation modelling technique. In addition, this research also shows that investigators and managers should pay attention to affects, because affects have a unique role in relationship customer behavior.

  2. Seismic performance of existing R.C. framed buildings

    Directory of Open Access Journals (Sweden)

    Sameh A. El-Betar

    2017-08-01

    Full Text Available The earthquakes disasters basically occur due to buildings damage not because of the earth shaking. Therefore, the countries have being updated the seismic codes. The seismic loads for buildings design in Egyptian Code have been changed from (EC-1994 to (ECP-201, 2012. On the other hand, the need is raised to study the vulnerability of existing buildings, which can be divided into the buildings designed to resist the gravity loads only (GLD and the buildings designed according to Egyptian code (EC-1994. Comparison between forces due to Egyptian code for loads (EC-1994 and (ECP-201, 2012 is carried out on the multi-stories R.C. framed buildings which are the most common type of existing buildings in Egypt. To investigate the vulnerability of existing buildings, nonlinear static pushover analysis is conducted to evaluate the real strength of the existing buildings. Moreover, it is considered a useful and effective tool for the performance of three framed buildings: 3, 6 and 10 stories due to expected future earthquakes. Finally, it is found that the vulnerability of existing GLD buildings occurs at expected ground accelerations (ag greater than 0.125 g in Egyptian seismic map, while the EC-94 designed buildings behave elastically up to (ag equals to 0.2 g and above that a slight damage may occur.

  3. Seismic evaluation of non-seismically designed existing Magnox nuclear power plants

    International Nuclear Information System (INIS)

    Kunar, R.R.

    1984-01-01

    The philosophy and method adopted for the seismic assessment of three existing Magnox nuclear stations in the United Kingdom are presented in this paper. The plants were not seismically designed. The particular procedures that were applied were tailored to suit the difficulties of lack of data which is somewhat inevitable for plants designed and built about 25 to 30 years ago. Special procedures included on-site testing with a portable shake table, low vibration testing using a structural dynamics analyser, and on-site inspections. The low vibration testing was most invaluable in detecting differences between 'as-built' conditions and the engineering drawings. From the point of view of economics, this was more effective than conducting full structural surveys to determine the as-built conditions. The testing results also provided confidence in the answers from numerical models. The philosophy adopted for the Magnox reactors in the seismic assessment was to determine what peak ground accelerations the sites can sustain and then evaluate the chances of exceeding the ground accelerations over the remaining lifetime of the plants. The peak ground acceleration for each site was determined on the basis of the criteria of safe shutdown and prevention of significant off-site radiological exposure

  4. Pre-Existing Condition Insurance Plan Data

    Data.gov (United States)

    U.S. Department of Health & Human Services — The Affordable Care Act created the new Pre-Existing Condition Insurance Plan (PCIP) program to make health insurance available to Americans denied coverage by...

  5. Remarks on the existence of non equilibrium dynamics

    International Nuclear Information System (INIS)

    Marchioro, C.; Pellegrinotti, A.; Pulvirenti, M.

    1981-01-01

    The authors give an existence theorem for the dynamics of an infinite system of anharmonic oscillators. They obtain another proof of the existence of the dynamics in the case of one-dimensional system of infinitely many particles interacting via a bounded potential. The case of very singular potential is also solved. (Auth.)

  6. Pre-existing oblique transfer zones and transfer/transform relationships in continental margins: New insights from the southeastern Gulf of Aden, Socotra Island, Yemen

    Science.gov (United States)

    Bellahsen, N.; Leroy, S.; Autin, J.; Razin, P.; d'Acremont, E.; Sloan, H.; Pik, R.; Ahmed, A.; Khanbari, K.

    2013-11-01

    Transfer zones are ubiquitous features in continental rifts and margins, as are transform faults in oceanic lithosphere. Here, we present a structural study of the Hadibo Transfer Zone (HTZ), located in Socotra Island (Yemen) in the southeastern Gulf of Aden. There, we interpret this continental transfer fault zone to represent a reactivated pre-existing structure. Its trend is oblique to the direction of divergence and it has been active from the early up to the latest stages of rifting. One of the main oceanic fracture zones (FZ), the Hadibo-Sharbithat FZ, is aligned with and appears to be an extension of the HTZ and is probably genetically linked to it. Comparing this setting with observations from other Afro-Arabian rifts as well as with passive margins worldwide, it appears that many continental transfer zones are reactivated pre-existing structures, oblique to divergence. We therefore establish a classification system for oceanic FZ based upon their relationship with syn-rift structures. Type 1 FZ form at syn-rift structures and are late syn-rift to early syn-OCT. Type 2 FZ form during the OCT formation and Type 3 FZ form within the oceanic domain, after the oceanic spreading onset. The latter are controlled by far-field forces, magmatic processes, spreading rates, and oceanic crust rheology.

  7. Structural Power and International Relations Analysis: "Fill your basket, get your preferences"

    OpenAIRE

    Pustovitovskij, Andrej; Kremer, Jan-Frederik

    2011-01-01

    In this article, we will address current deficits of the study of power in IR by introducing a new concept of structural power. After briefly presenting existing concepts of relational power, of structural power as well as of conceptualizing power as the possession of resources (power-as-resources), we will introduce our concept of structural power as an approach suitable for bridging the gap between existing concepts (by strongly focusing on the importance of the structural level). We will s...

  8. 40 CFR 417.84 - Pretreatment standards for existing sources.

    Science.gov (United States)

    2010-07-01

    ...) EFFLUENT GUIDELINES AND STANDARDS SOAP AND DETERGENT MANUFACTURING POINT SOURCE CATEGORY Manufacture of Liquid Soaps Subcategory § 417.84 Pretreatment standards for existing sources. Any existing source...

  9. 40 CFR 427.44 - Pretreatment standards for existing sources.

    Science.gov (United States)

    2010-07-01

    ...) EFFLUENT GUIDELINES AND STANDARDS ASBESTOS MANUFACTURING POINT SOURCE CATEGORY Asbestos Paper (Elastomeric Binder) Subcategory § 427.44 Pretreatment standards for existing sources. Any existing source subject to...

  10. 40 CFR 427.34 - Pretreatment standards for existing sources.

    Science.gov (United States)

    2010-07-01

    ...) EFFLUENT GUIDELINES AND STANDARDS ASBESTOS MANUFACTURING POINT SOURCE CATEGORY Asbestos Paper (Starch Binder) Subcategory § 427.34 Pretreatment standards for existing sources. Any existing source subject to...

  11. Tachyons imply the existence of a privileged frame

    Energy Technology Data Exchange (ETDEWEB)

    Sjoedin, T.; Heylighen, F.

    1985-12-16

    It is shown that the existence of faster-than-light signals (tachyons) would imply the existence (and detectability) of a privileged inertial frame and that one can avoid all problems with reversed-time order only by using absolute synchronization instead of the standard one. The connection between these results and the EPR-paradox is discussed.

  12. The settlement of foundation of existing large structure on soft ground and investigation of its allowable settlement

    International Nuclear Information System (INIS)

    Okamoto, Toshiro

    1987-01-01

    In our laboratory a study of siting on quarternary ground is followed to make possible to construct a nuclear power plant on soil ground in Japan, a important subject is to understand bearing capacity, settlement and seismic responce of foundation. So measured data are collected about relation between ground and type of foundation, total settlement and differential settlement of already constructed large structures, and it is done to investigate the real condition and to examine allowable settlement. Investigated structures are mainly foreign nuclear power plant and domestic and foreign high buildings. The higher buildings are, the more raft foundation are for type of foundation and the higher contact pressure are to similar to a nuclear power plant. So discussion is done about mainly raft foundation. It is found that some measured maximum total settlements are larger than already proposed allowable values. So empirical allowable settlement is derived from measured values considering the effect of the width of base slab, contact pressure and foundation ground. Differential settlement is investigated about relation to maximum total settlement, and is formulated considering the width and the rigidity of base slab. Beside the limit of differential settlement is obtained as foundation is damaged, and the limit of maximum total settlement is obtained by combining this and above mentioned relation. Obtained allowable value is largely influenced by the width of base slab, and becomes less severe than some already proposed values. So it is expected that deformation of foundation is rationaly investigated when large structure as nuclear power plant is constructed on soft ground. (author)

  13. The Application of Buckling Reinforced Bracing and Shear Wall in Retrofitting of Existing Concrete Building

    Directory of Open Access Journals (Sweden)

    Mahdi Izadi

    2015-06-01

    Full Text Available Vulnerable buildings and their rehabilitation are important problems for earthquake regions. In recent decades the goal of building rehabilitation and strengthening has gained different rehabilitation systems. However, most of these strengthening techniques disturb the occupants, who must vacate the building during renovation. Several retrofitting techniques such as addition masonry infill wall, application of buckling restrained braces and local modification of components has been studied in order to improve the overall seismic performance of such buildings. In response to many of the practical issues and economic considerations, engineers use often convergent unbuckling steel bracing frames as the lateral load resisting system during an earthquake.This kind of bracings increases the hardness and strength of concrete structures.The aim of the present study is the evaluation and comparison of seismic performance and retrofitting of an existing 7-storeys concrete structure with buckling restrained bracings and shear walls by nonlinear static procedure (NSP and accordance with cod-361. The results show that the buckling restrained bracing, decreased drift to acceptable levels and Structure behaves on the life safety of performance level.

  14. DSIbin : Identifying dynamic data structures in C/C++ binaries

    NARCIS (Netherlands)

    Rupprecht, Thomas; Chen, Xi; White, David H.; Boockmann, Jan H.; Luttgen, Gerald; Bos, Herbert

    2017-01-01

    Reverse engineering binary code is notoriously difficult and, especially, understanding a binary's dynamic data structures. Existing data structure analyzers are limited wrt. program comprehension: they do not detect complex structures such as skip lists, or lists running through nodes of different

  15. Tribological behavior of inconel 718 in sodium cooled reactor environments

    International Nuclear Information System (INIS)

    Wilson, W.L.; Galioto, T.A.; Schrock, S.L.

    1976-01-01

    Results of the present study on the tribological behavior of Inconel 718 in a sodium environment are summarized as follows: (a) Stroke lengths less than or equal to one-half the test pin diameter result in higher friction coefficients. (b) At elevated temperatures, the formation of a lubricative surface film can significantly influence the frictional behavior. (c) Tangential forces present during static dwell periods result in greater bonding tendencies. (d) Increasing contact pressure during static dwell periods results in lower breakaway friction coefficients

  16. [Classification of organisms and structuralism in biology].

    Science.gov (United States)

    Vasil'eva, L I

    2001-01-01

    Structuralism in biology is the oldest trend oriented to the search for natural "laws of forms" comparable with laws of growth of crystal, was revived at the end of 20th century on the basis of structuralist thought in socio-humanitarian sciences. The development of principal ideas of the linguistic structuralism in some aspects is similar to that of biological systematics, especially concerning the relationships between "system" and "evolution". However, apart from this general similarity, biological structuralism is strongly focused on familiar problems of the origin of diversity in nature. In their striving for the renovation of existing views, biological structuralists oppose the neo-darwinism emphasizing the existence of "law of forms", that are independent on heredity and genetic "determinism". The trend to develop so-called "rational taxonomy" is also characteristic of biological structuralism but this attempt failed being connected neither with Darwin's historicism nor with Plato's typology.

  17. General Equilibrium in a Segmented Market Economy with Convex Transaction Cost: Existence, Efficiency, Commodity and Fiat Money

    OpenAIRE

    Starr, Ross M.

    2002-01-01

    This study derives the monetary structure of transactions, the use of commodity or fiat money, endogenously from transaction costs in a segmented market general equilibrium model. Market segmentation means there are separate budget constraints for each transaction: budgets balance in each transaction separately. Transaction costs imply differing bid and ask (selling and buying) prices. The most liquid instruments are those with the lowest proportionate bid/ask spread in equilibrium. Exist...

  18. Existence Results for Incompressible Magnetoelasticity

    Czech Academy of Sciences Publication Activity Database

    Kružík, Martin; Stefanelli, U.; Zeman, J.

    2015-01-01

    Roč. 35, č. 6 (2015), s. 2615-2623 ISSN 1078-0947 R&D Projects: GA ČR GA13-18652S Institutional support: RVO:67985556 Keywords : magnetoelasticity * magnetostrictive solids * incompressibility * existence of minimizers * quasistatic evolution * energetic solution Subject RIV: BA - General Mathematics Impact factor: 1.127, year: 2015 http://library.utia.cas.cz/separaty/2015/MTR/kruzik-0443017.pdf

  19. 75 FR 45013 - Pre-Existing Condition Insurance Plan Program

    Science.gov (United States)

    2010-07-30

    ... Department of Homeland Security's U.S. Citizenship and Immigration Services (USCIS) Systematic Alien... pre-existing condition based on evidence of the existence or history of certain medical or health...

  20. The Quest to Solve Problems That Don’t Exist: Thought Artifacts in Contemporary Ontology

    Directory of Open Access Journals (Sweden)

    Kastrup Bernardo

    2017-10-01

    Full Text Available Questions about the nature of reality and consciousness remain unresolved in philosophy today, but not for lack of hypotheses. Ontologies as varied as physicalism, microexperientialism and cosmopsychism enrich the philosophical menu. Each of these ontologies faces a seemingly fundamental problem: under physicalism, for instance, we have the ‘hard problem of consciousness,’ whereas under microexperientialism we have the ‘subject combination problem.’ I argue that these problems are thought artifacts, having no grounding in empirical reality. In a manner akin to semantic paradoxes, they exist only in the internal logico-conceptual structure of their respective ontologies.

  1. Unmanned aerial vehicle (UAV) application to the structural health assessment of large civil engineering structures

    Science.gov (United States)

    Castiglioni, Carlo A.; Rabuffetti, Angelo S.; Chiarelli, Gian P.; Brambilla, Giovanni; Georgi, Julia

    2017-09-01

    This paper summarizes the experience gained in the structural assessment of an existing Thermal Power Plant (TPP) located near Pristina, focusing on the cooling tower and the flue gas stack, which are the main structures of the TPP. Scope of the work was the evaluation of the actual conditions of the structures and to identify the eventual repair measures in order to guarantee a safe and reliable operation of the TPP in view of the extension of its operational lifetime for the next 30 years. With this aim, a sequence of different activities was performed, like: a topographic survey to compare the actual geometrical configuration with the design one, an investigation of the material properties, an in depth visual inspection in order to detect any visible existing damage. Due to the very high elevations of the constructions and to the lack of appropriate structures aimed to their inspections and maintenance, this activity could not be performed without using Unmanned Aerial Vehicle (UAV). This resulted the safest, most economical and less time-consuming solution identified to map the surface damage in the reinforced concrete elements of these large structures including zones that could not be inspected because out of reach by other means.

  2. Hadronic interaction and structure of exotic nuclei

    International Nuclear Information System (INIS)

    Otsuka, Takaharu

    2009-01-01

    I will overview recent studies on the evolution of the shell structure in stable and exotic nuclei, and will show its relevance to hadronic interaction, including nuclear forces. This shell evolution is primarily due to the tensor force. The robust mechanism and some examples will be presented. Such examples include the disappearance of existing magic numbers and the appearance of new ones. The shell structure and existing limit of nuclei depend also on the three-body interaction in a specific way. I will sketch how the Δ-hole excitation induced three-body force (Fujita-Miyazawa force) modifies them. (author)

  3. Nonlinear seismic soil-structure interaction analysis of nuclear power plant structures

    International Nuclear Information System (INIS)

    Khanna, J.K.; Setlur, A.V.; Pathak, D.V.

    1977-01-01

    The heterogeneous and nonlinear soil medium and the detailed three-dimensional structure are synthesized to determine the seismic response to soil-structure systems. The approach is particularly attractive in a design office environment since it: a) leads to interactive motion at the soil-structure interface; b) uses existing public domain programs such as SAPIV, LUSH and FLUSH with marginal modifications; and c) meets current regulatory requirements for soil-structure interaction analysis. Past methods differ from each other depending on the approach adopted for soil and structure representations and procedures for solving the governing differential equations. Advantages and limitations of these methods are reviewed. In the current approach, the three-dimensional structure is represented by the dynamic characteristics of its fixed base condition. This representation is ideal when structures are designed to be within elastic range. An important criterion is the design of the nuclear power plant structures. Model damping coefficients are varied to reflect the damping properties of different structural component materials. The detailed structural model is systematically reduced to reflect important dynamic behavior with simultaneous storing of intermediate information for retrieval of detailed structural response. Validity of the approach has been established with simple numerical experiments. (Auth.)

  4. Magnetic nesting and co-existence of ferromagnetism and superconductivity

    International Nuclear Information System (INIS)

    Elesin, V.F.; Kapaev, V.V.; Kopaev, Yu.V.

    2004-01-01

    In the case of providing for the magnetic nesting conditions of the electron spin dispersion law the co-existence of ferromagnetism and superconductivity is possible by any high magnetization. The co-existence of ferromagnetism and superconductivity in the layered cuprate compounds of the RuSr 2 GdCu 2 O 8 -type is explained on this basis, wherein due to the nonstrict provision of the magnetic nesting condition there exists the finite but sufficiently high critical magnetization [ru

  5. 40 CFR 415.344 - Pretreatment standards for existing sources (PSES).

    Science.gov (United States)

    2010-07-01

    ... Pigments Production Subcategory § 415.344 Pretreatment standards for existing sources (PSES). (a) Existing... chrome pigments process wastewater into a publicly owned treatment works are subject only to the... standards for existing sources (PSES): Subpart AH—Chrome Pigments Pollutant or pollutant property PSES...

  6. Alternative for Summer Use of Solar Air Heaters in Existing Buildings

    Directory of Open Access Journals (Sweden)

    Sergio L. González-González

    2017-07-01

    Full Text Available Among solar thermal technologies for indoor heating, solar air heaters (SAH are appealing for implementation on existing buildings due to their simplicity, fewer risks related to the working fluid, and possible independence from the building structure. However, existing research work mainly focuses on winter use and still fails in providing effective solutions for yearly operation, which would enhance their interest. With the aim of analysing an alternative summer use, this work firstly characterises a double channel-single pass solar air collector through experimentation. From the obtained results, modelling and simulation tasks have been conducted to evaluate the possibilities of using hot air, provided by the SAH, while operating under summer conditions within a closed loop, to feed an air-to-water heat exchanger for domestic hot water (DHW production. The system is studied through simulation under two different configurations for a case study in Valladolid (Spain, during the period from May to September for different airflows in the closed loop. Results show that daily savings can vary from 27% to 85% among the different operating conditions; a configuration where make-up water is fed to the heat exchanger being preferable, with a dedicated water tank for the solar heated water storage of the minimum possible volume. The more favourable results for the harshest months highlight the interest of extending the use of the solar air heaters to the summer period.

  7. 78 FR 13835 - Harmonization of Airworthiness Standards-Miscellaneous Structures Requirements

    Science.gov (United States)

    2013-03-01

    ... Airworthiness Standards--Miscellaneous Structures Requirements AGENCY: Federal Aviation Administration (FAA... and Dynamics Harmonization Working Group (LDHWG) and the General Structures Harmonization Working Group (GSHWG) to review existing structures regulations and recommend changes that would eliminate...

  8. Acoustic-gravity nonlinear structures

    Directory of Open Access Journals (Sweden)

    D. Jovanović

    2002-01-01

    Full Text Available A catalogue of nonlinear vortex structures associated with acoustic-gravity perturbations in the Earth's atmosphere is presented. Besides the previously known Kelvin-Stewart cat's eyes, dipolar and tripolar structures, new solutions having the form of a row of counter-rotating vortices, and several weakly two-dimensional vortex chains are given. The existence conditions for these nonlinear structures are discussed with respect to the presence of inhomogeneities of the shear flows. The mode-coupling mechanism for the nonlinear generation of shear flows in the presence of linearly unstable acoustic-gravity waves, possibly also leading to intermittency and chaos, is presented.

  9. Experimental Study on Temperature Behavior of SSC (Stiffened Steel Plate Concrete) Structures

    International Nuclear Information System (INIS)

    Lee, K. J.; Ham, K. W.; Park, D. S.; Kwon, K. J.

    2008-01-01

    SSC(Stiffened Steel plate Concrete) module method uses steel plate instead of reinforcing bar and mold in existing RC structure. Steel plate modules are fabricated in advance, installed and poured with concrete in construction field, so construction period is remarkably shortened by SC module technique. In case of existence of temperature gap between internal and external structure surface such as containment building, thermal stress is taken place and as a result of it, structural strength is deteriorated. In this study, we designed two test specimens and several tests with temperature heating were conducted to evaluate temperature behavior of SSC structures and RC structure

  10. Existence and non-existence for the full thermomechanical Souza–Auricchio model of shape memory wires

    Czech Academy of Sciences Publication Activity Database

    Krejčí, Pavel; Stefanelli, U.

    2011-01-01

    Roč. 16, č. 4 (2011), s. 349-365 ISSN 1081-2865 R&D Projects: GA ČR GAP201/10/2315 Institutional research plan: CEZ:AV0Z10190503 Keywords : shape memory alloys * thermomechanics * existence result * blowup in finite time Subject RIV: BA - General Mathematics Impact factor: 1.012, year: 2011 http://mms.sagepub.com/content/early/2011/03/11/1081286510386935.abstract

  11. Existence and non-existence for the full thermomechanical Souza–Auricchio model of shape memory wires

    Czech Academy of Sciences Publication Activity Database

    Krejčí, Pavel; Stefanelli, U.

    2011-01-01

    Roč. 16, č. 4 (2011), s. 349-365 ISSN 1081-2865 R&D Projects: GA ČR GAP201/10/2315 Institutional research plan: CEZ:AV0Z10190503 Keywords : shape memory alloys * thermomechanics * existence result * blowup in finite time Subject RIV: BA - General Mathematics Impact factor: 1.012, year: 2011 http:// mms .sagepub.com/content/early/2011/03/11/1081286510386935.abstract

  12. Compact complex surfaces with geometric structures related to split quaternions

    International Nuclear Information System (INIS)

    Davidov, Johann; Grantcharov, Gueo; Mushkarov, Oleg; Yotov, Miroslav

    2012-01-01

    We study the problem of existence of geometric structures on compact complex surfaces that are related to split quaternions. These structures, called para-hypercomplex, para-hyperhermitian and para-hyperkähler, are analogs of the hypercomplex, hyperhermitian and hyperkähler structures in the definite case. We show that a compact 4-manifold carries a para-hyperkähler structure iff it has a metric of split signature together with two parallel, null, orthogonal, pointwise linearly independent vector fields. Every compact complex surface admitting a para-hyperhermitian structure has vanishing first Chern class and we show that, unlike the definite case, many of these surfaces carry infinite-dimensional families of such structures. We provide also compact examples of complex surfaces with para-hyperhermitian structures which are not locally conformally para-hyperkähler. Finally, we discuss the problem of non-existence of para-hyperhermitian structures on Inoue surfaces of type S 0 and provide a list of compact complex surfaces which could carry para-hypercomplex structures.

  13. Basic concept on the responses of structural members and structures under impact or impulsive loadings

    International Nuclear Information System (INIS)

    Takeda, J.I.; Tachikawa, H.; Fujimoto, K.

    1982-01-01

    The responses of structural members and structures subjected to impact or impulsive loadings are generated by the interaction between acting bodies and structures, and the interaction is affected by many factors, e.g. the relations of masses, sizes, rigidities, etc. between acting bodies and structures and especially by relative velocity. The development of the responses of structural members and structures are controlled by the constitutive equations and failure criteria of constituent materials, the relationships of cowork system between the constituent materials and existing stress waves. Furthermore, the first two are influenced by rate effects and they all widely change by the speeds of impact and impulsive loadings. This paper deals with the physical meaning of the responses of structures under impact and impulsive loadings. (orig.) [de

  14. Co-existence in multispecies biofilm communities

    DEFF Research Database (Denmark)

    Røder, Henriette Lyng

    of these emergent properties which are relevant to as diverse areas as clinical settings and natural systems. In this thesis, I have attempted to contribute to our knowledge on the multispecies interactions with a special focus on biofilm communities. I was especially interested in how co-existing species affect...... each other and in understanding the key mechanisms and interactions involved. In the introduction of this thesis the most important concepts of multi-species interactions and biofilm development are explained. After this the topic changes to the various ways of examining community interactions...... and production. The analysis was further extended in manuscript 3, in which the effect of social interac-tions on biofilm formation in multispecies co-cultures isolated from a diverse range of environments was examined. The question raised was whether the interspecific interactions of co-existing bacteria...

  15. A Systematic Review on the Existing Screening Pathways for Lynch Syndrome Identification

    Directory of Open Access Journals (Sweden)

    Alessia Tognetto

    2017-09-01

    Full Text Available BackgroundLynch syndrome (LS is the most common hereditary colon cancer syndrome, accounting for 3–5% of colorectal cancer (CRC cases, and it is associated with the development of other cancers. Early detection of individuals with LS is relevant, since they can take advantage of life-saving intensive care surveillance. The debate regarding the best screening policy, however, is far from being concluded. This prompted us to conduct a systematic review of the existing screening pathways for LS.MethodsWe performed a systematic search of MEDLINE, ISI Web of Science, and SCOPUS online databases for the existing screening pathways for LS. The eligibility criteria for inclusion in this review required that the studies evaluated a structured and permanent screening pathway for the identification of LS carriers. The effectiveness of the pathways was analyzed in terms of LS detection rate.ResultsWe identified five eligible studies. All the LS screening pathways started from CRC cases, of which three followed a universal screening approach. Concerning the laboratory procedures, the pathways used immunohistochemistry and/or microsatellite instability testing. If the responses of the tests indicated a risk for LS, the genetic counseling, performed by a geneticist or a genetic counselor, was mandatory to undergo DNA genetic testing. The overall LS detection rate ranged from 0 to 5.2%.ConclusionThis systematic review reported different existing pathways for the identification of LS patients. Although current clinical guidelines suggest to test all the CRC cases to identify LS cases, the actual implementation of pathways for LS identification has not been realized. Large-scale screening programs for LS have the potential to reduce morbidity and mortality for CRC, but coordinated efforts in educating all key stakeholders and addressing public needs are still required.

  16. Evaluating Hierarchical Structure in Music Annotations.

    Science.gov (United States)

    McFee, Brian; Nieto, Oriol; Farbood, Morwaread M; Bello, Juan Pablo

    2017-01-01

    Music exhibits structure at multiple scales, ranging from motifs to large-scale functional components. When inferring the structure of a piece, different listeners may attend to different temporal scales, which can result in disagreements when they describe the same piece. In the field of music informatics research (MIR), it is common to use corpora annotated with structural boundaries at different levels. By quantifying disagreements between multiple annotators, previous research has yielded several insights relevant to the study of music cognition. First, annotators tend to agree when structural boundaries are ambiguous. Second, this ambiguity seems to depend on musical features, time scale, and genre. Furthermore, it is possible to tune current annotation evaluation metrics to better align with these perceptual differences. However, previous work has not directly analyzed the effects of hierarchical structure because the existing methods for comparing structural annotations are designed for "flat" descriptions, and do not readily generalize to hierarchical annotations. In this paper, we extend and generalize previous work on the evaluation of hierarchical descriptions of musical structure. We derive an evaluation metric which can compare hierarchical annotations holistically across multiple levels. sing this metric, we investigate inter-annotator agreement on the multilevel annotations of two different music corpora, investigate the influence of acoustic properties on hierarchical annotations, and evaluate existing hierarchical segmentation algorithms against the distribution of inter-annotator agreement.

  17. Evaluating Hierarchical Structure in Music Annotations

    Directory of Open Access Journals (Sweden)

    Brian McFee

    2017-08-01

    Full Text Available Music exhibits structure at multiple scales, ranging from motifs to large-scale functional components. When inferring the structure of a piece, different listeners may attend to different temporal scales, which can result in disagreements when they describe the same piece. In the field of music informatics research (MIR, it is common to use corpora annotated with structural boundaries at different levels. By quantifying disagreements between multiple annotators, previous research has yielded several insights relevant to the study of music cognition. First, annotators tend to agree when structural boundaries are ambiguous. Second, this ambiguity seems to depend on musical features, time scale, and genre. Furthermore, it is possible to tune current annotation evaluation metrics to better align with these perceptual differences. However, previous work has not directly analyzed the effects of hierarchical structure because the existing methods for comparing structural annotations are designed for “flat” descriptions, and do not readily generalize to hierarchical annotations. In this paper, we extend and generalize previous work on the evaluation of hierarchical descriptions of musical structure. We derive an evaluation metric which can compare hierarchical annotations holistically across multiple levels. sing this metric, we investigate inter-annotator agreement on the multilevel annotations of two different music corpora, investigate the influence of acoustic properties on hierarchical annotations, and evaluate existing hierarchical segmentation algorithms against the distribution of inter-annotator agreement.

  18. Reliability-based optimization of engineering structures

    DEFF Research Database (Denmark)

    Sørensen, John Dalsgaard

    2008-01-01

    The theoretical basis for reliability-based structural optimization within the framework of Bayesian statistical decision theory is briefly described. Reliability-based cost benefit problems are formulated and exemplitied with structural optimization. The basic reliability-based optimization...... problems are generalized to the following extensions: interactive optimization, inspection and repair costs, systematic reconstruction, re-assessment of existing structures. Illustrative examples are presented including a simple introductory example, a decision problem related to bridge re...

  19. Development of the electromagnetic tomography system. Field test results using existing equipment; EM tomography system no kaihatsu. Kison sochi ni yoru test sokutei kekka

    Energy Technology Data Exchange (ETDEWEB)

    Kumekawa, Y; Miura, Y; Takasugi, S [Geothermal Energy Research and Development Co. Ltd., Tokyo (Japan); Arai, E [Metal Mining Agency of Japan, Tokyo (Japan)

    1996-05-01

    With the purpose of developing an electromagnetic tomography system, an observation was carried out with existing equipment combined, and the data was analyzed. The measuring equipment consisted of existing borehole vertical magnetic field sensors as the sensor part, MT method receivers as the receiving device, and existing CSMT method transmitters as the transmitting device. The measuring was performed at the Richmond Field Station which was abundant in existing data and which had a comparatively simple resistivity structure. The borehole vertical magnetic field sensors were lowered inside the borehole, and signal sources were arranged at 10m apart on the traverse line in the direction from northeast to southwest with the borehole as the center. The analysis of the data was made with the use of EM1D by three models, namely, 10 ohm{center_dot}m homogeneous earth model, 100 ohm{center_dot}m homogeneous earth model, and horizontal 7 layer model prepared on the basis of electric logging results; and a comparative examination was made against the measured data. As a result, it was demonstrated that the test measurement agreed very well with the model from the electric logging results and that it was the data reflecting a resistivity structure. 8 refs., 6 figs.

  20. Monte Carlo determination of heteroepitaxial misfit structures

    DEFF Research Database (Denmark)

    Baker, J.; Lindgård, Per-Anker

    1996-01-01

    We use Monte Carlo simulations to determine the structure of KBr overlayers on a NaCl(001) substrate, a system with large (17%) heteroepitaxial misfit. The equilibrium relaxation structure is determined for films of 2-6 ML, for which extensive helium-atom scattering data exist for comparison...

  1. Isolation and structural analysis of antihypertensive peptides that exist naturally in Gouda cheese.

    Science.gov (United States)

    Saito, T; Nakamura, T; Kitazawa, H; Kawai, Y; Itoh, T

    2000-07-01

    Seven kinds of ripened cheeses (8-mo-aged and 24-mo-aged Gouda, Emmental, Blue, Camembert, Edam, and Havarti) were homogenized with distilled water, and water-soluble peptides were prepared by C-18 hydrophobic chromatography. The inhibitory activity to angiotensin I-converting enzyme and decrease in the systolic blood pressure in spontaneously hypertensive rats were measured before and after oral administration of each peptide sample. The strongest depressive effect in the systolic blood pressure (-24.7 mm Hg) and intensive inhibitory activity to angiotensin I-converting enzyme (75.7%) were detected in the peptides from 8-mo-aged Gouda cheese. Four peptides were isolated by HPLC with reverse-phase and gel filtration modes. Their chemical structures and origins, clarified by combination analyses of protein sequencing, amino acid composition, and mass spectrometry, were as follows: peptide A, Arg-Pro-Lys-His-Pro-Ile-Lys-His-Gln [alpha(s1)-casein (CN), B-8P; f 1-9]; peptide B, Arg-Pro-Lys-His-Pro-Ile-Lys-His-Gln-Gly-Leu-Pro-Gln (alpha(s1)-CN, B-8P; f 1-13); peptide F, Tyr-Pro-Phe-Pro-Gly-Pro-Ile-Pro-Asn (beta-CN, A2-5P; f 60-68); and peptide G, Met-Pro-Phe-Pro-Lys-Tyr-Pro-Val-Gln-Pro-Phe (beta-CN, A2-5P; f 109-119). Peptides A and F, which were chemically synthesized, showed potent angiotensin I-converting enzyme inhibitory activity with little antihypertensive effects.

  2. The review on tessellation origami inspired folded structure

    Science.gov (United States)

    Chu, Chai Chen; Keong, Choong Kok

    2017-10-01

    Existence of folds enhances the load carrying capacity of a folded structure which makes it suitable to be used for application where large open space is required such as large span roof structures and façade. Folded structure is closely related to origami especially the tessellation origami. Tessellation origami provides a folded configuration with facetted surface as a result from repeated folding pattern. Besides that, tessellation origami has flexible folding mechanism that produced a variety of 3-dimensional folded configurations. Despite the direct relationship between fold in origami and folded structure, the idea of origami inspired folded structure is not properly reviewed in the relevant engineering field. Hence, this paper aims to present the current studies from related discipline which has direct relation with application of tessellation origami in folded structure. First, tessellation origami is properly introduced and defined. Then, the review covers the topic on the origami tessellation design suitable for folded structure, its modeling and simulation method, and existing studies and applications of origami as folded structure is presented. The paper also includes the discussion on the current issues related to each topic.

  3. Existence of weak solutions to a nonlinear reaction-diffusion system with singular sources

    Directory of Open Access Journals (Sweden)

    Ida de Bonis

    2017-09-01

    Full Text Available We discuss the existence of a class of weak solutions to a nonlinear parabolic system of reaction-diffusion type endowed with singular production terms by reaction. The singularity is due to a potential occurrence of quenching localized to the domain boundary. The kind of quenching we have in mind is due to a twofold contribution: (i the choice of boundary conditions, modeling in our case the contact with an infinite reservoir filled with ready-to-react chemicals and (ii the use of a particular nonlinear, non-Lipschitz structure of the reaction kinetics. Our working techniques use fine energy estimates for approximating non-singular problems and uniform control on the set where singularities are localizing.

  4. A novel knowledge-based potential for RNA 3D structure evaluation

    Science.gov (United States)

    Yang, Yi; Gu, Qi; Zhang, Ben-Gong; Shi, Ya-Zhou; Shao, Zhi-Gang

    2018-03-01

    Ribonucleic acids (RNAs) play a vital role in biology, and knowledge of their three-dimensional (3D) structure is required to understand their biological functions. Recently structural prediction methods have been developed to address this issue, but a series of RNA 3D structures are generally predicted by most existing methods. Therefore, the evaluation of the predicted structures is generally indispensable. Although several methods have been proposed to assess RNA 3D structures, the existing methods are not precise enough. In this work, a new all-atom knowledge-based potential is developed for more accurately evaluating RNA 3D structures. The potential not only includes local and nonlocal interactions but also fully considers the specificity of each RNA by introducing a retraining mechanism. Based on extensive test sets generated from independent methods, the proposed potential correctly distinguished the native state and ranked near-native conformations to effectively select the best. Furthermore, the proposed potential precisely captured RNA structural features such as base-stacking and base-pairing. Comparisons with existing potential methods show that the proposed potential is very reliable and accurate in RNA 3D structure evaluation. Project supported by the National Science Foundation of China (Grants Nos. 11605125, 11105054, 11274124, and 11401448).

  5. Buckling of Ship Structures

    CERN Document Server

    Shama, Mohamed

    2013-01-01

    Buckling of Ship Structures presents a comprehensive analysis of the buckling problem of ship structural members. A full analysis of the various types of loadings and stresses imposed on ship plating and primary and secondary structural members is given. The main causes and consequences of the buckling mode of failure of ship structure and the methods commonly used to control buckling failure are clarified. This book contains the main equations required to determine the critical buckling stresses for both ship plating and the primary and secondary stiffening structural members. The critical buckling stresses are given for ship plating subjected to the induced various types of loadings and having the most common boundary conditions encountered in ship structures.  The text bridges the gap existing in most books covering the subject of buckling of ship structures in the classical analytical format, by putting the emphasis on the practical methods required to ensure safety against buckling of ship structur...

  6. Existing sustainable renovation concepts for single-family houses

    DEFF Research Database (Denmark)

    Tommerup, Henrik M.; Vanhoutteghem, Lies; Svendsen, Svend

    2010-01-01

    In the Nordic Innovation Centre Project, SuccessFamilies, the main objective is to change the business environment in order to speed up the implementation of sustainable renovation of single-family houses – proposing new service concepts that will combine both the technical solutions, financing...... with individual solutions, traditional warehouses ”do-it-yourself-shops” and some actors marketing single products. To speed up the implementation of sustainable renovation of single-family houses there is a great need for full-service packages. Existing technical renovation concepts, typically focusing...... services as well as other promoting issues to overcome the behavioural, organizational, legal and social barriers that exist in sustainable renovation. A starting point for such a change has been to get an overview of the existing sustainable renovation concepts, i.e. full-service concepts and technical...

  7. Evaluating bacterial gene-finding HMM structures as probabilistic logic programs

    DEFF Research Database (Denmark)

    Mørk, Søren; Holmes, Ian

    2012-01-01

    , a probabilistic dialect of Prolog. Results: We evaluate Hidden Markov Model structures for bacterial protein-coding gene potential, including a simple null model structure, three structures based on existing bacterial gene finders and two novel model structures. We test standard versions as well as ADPH length...

  8. 40 CFR 60.2992 - What is an existing incineration unit?

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 6 2010-07-01 2010-07-01 false What is an existing incineration unit... Times for Other Solid Waste Incineration Units That Commenced Construction On or Before December 9, 2004 Applicability of State Plans § 60.2992 What is an existing incineration unit? An existing incineration unit is...

  9. Characterization of Injection Molded Structures

    DEFF Research Database (Denmark)

    Sun, Ling; Søgaard, Emil; Andersen, Nis Korsgaard

    for different applications. We show how to correlate the structures of the polymer replicas with respect to their functionalities. Furthermore, we introduce how we coordinate with all partners in the “Nanoplast” project, and how we utilize the existing facilities of each method to understand structure......Microscopy has been widely applied to understand surface structures of solid samples. According to the instrumental methodology, there are different microscopy methods: optical microscopy, electron microscopy, and scanning probe microscopy (SPM). These microscopy methods have individual advantages...... and limitations. Therefore, it would be difficult to characterize complex, especially hierarchical structures by using only one method. Here we present a combined optical microscopy, scanning electron microscopy (SEM), and scanning probe microscopy study on injection molded structures. These structures are used...

  10. Flow and coherent structures around circular cylinders in shallow water

    Science.gov (United States)

    Zeng, Jie; Constantinescu, George

    2017-06-01

    Eddy-resolving numerical simulations are conducted to investigate the dynamics of the large-scale coherent structures around a circular cylinder in an open channel under very shallow flow conditions where the bed friction significantly affects the wake structure. Results are reported for three test cases, for which the ratio between the cylinder diameter, D, and the channel depth, H, is D/H = 10, 25, and 50, respectively. Simulation results show that a horseshoe vortex system forms in all test cases and the dynamics of the necklace vortices is similar to that during the breakaway sub-regime observed for cases when a laminar horseshoe vortex forms around the base of the cylinder. Given the shallow conditions and turbulence in the incoming channel flow, the necklace vortices occupy a large fraction of the flow depth (they penetrate until the free surface in the shallower cases with D/H = 25 and 50). The oscillations of the necklace vortices become less regular with increasing polar angle magnitude and can induce strong amplification of the bed shear stress beneath their cores. Strong interactions are observed between the legs of the necklace vortices and the eddies shed in the separated shear layers in the cases with D/H = 25 and 50. In these two cases, a vortex-street type wake is formed and strong three-dimensional effects are observed in the near-wake flow. A secondary instability in the form of arrays of co-rotating parallel horizontal vortices develops. Once the roller vortices get away from the cylinder, the horizontal vortices in the array orient themselves along the streamwise direction. This instability is not present for moderately shallow conditions (e.g., D/H ≈ 1) nor for very shallow cases when the wake changes to an unsteady bubble type (e.g., D/H = 50). For cases when this secondary instability is present, the horizontal vortices extend vertically over a large fraction of the flow depth and play an important role in the vertical mixing of fluid

  11. Overview of Existing Wind Energy Ordinances

    Energy Technology Data Exchange (ETDEWEB)

    Oteri, F.

    2008-12-01

    Due to increased energy demand in the United States, rural communities with limited or no experience with wind energy now have the opportunity to become involved in this industry. Communities with good wind resources may be approached by entities with plans to develop the resource. Although these opportunities can create new revenue in the form of construction jobs and land lease payments, they also create a new responsibility on the part of local governments to ensure that ordinances will be established to aid the development of safe facilities that will be embraced by the community. The purpose of this report is to educate and engage state and local governments, as well as policymakers, about existing large wind energy ordinances. These groups will have a collection of examples to utilize when they attempt to draft a new large wind energy ordinance in a town or county without existing ordinances.

  12. Interim Storage of Plutonium in Existing Facilities

    International Nuclear Information System (INIS)

    Woodsmall, T.D.

    1999-01-01

    'In this era of nuclear weapons disarmament and nonproliferation treaties, among many problems being faced by the Department of Energy is the safe disposal of plutonium. There is a large stockpile of plutonium at the Rocky Flats Environmental Technology Center and it remains politically and environmentally strategic to relocate the inventory closer to a processing facility. Savannah River Site has been chosen as the final storage location, and the Actinide Packaging and Storage Facility (APSF) is currently under construction for this purpose. With the ability of APSF to receive Rocky Flats material an estimated ten years away, DOE has decided to use the existing reactor building in K-Area of SRS as temporary storage to accelerate the removal of plutonium from Rocky Flats. There are enormous cost savings to the government that serve as incentive to start this removal as soon as possible, and the KAMS project is scheduled to receive the first shipment of plutonium in January 2000. The reactor building in K-Area was chosen for its hardened structure and upgraded seismic qualification, both resulting from an effort to restart the reactor in 1991. The KAMS project has faced unique challenges from Authorization Basis and Safety Analysis perspectives. Although modifying a reactor building from a production facility to a storage shelter is not technically difficult, the nature of plutonium has caused design and safety analysis engineers to make certain that the design of systems, structures and components included will protect the public, SRS workers, and the environment. A basic overview of the KAMS project follows. Plutonium will be measured and loaded into DOT Type-B shipping packages at Rocky Flats. The packages are 35-gallon stainless steel drums with multiple internal containment boundaries. DOE transportation vehicles will be used to ship the drums to the KAMS facility at SRS. They will then be unloaded, stacked and stored in specific locations throughout the

  13. 48 CFR 252.227-7021 - Rights in data-existing works.

    Science.gov (United States)

    2010-10-01

    ... of Provisions And Clauses 252.227-7021 Rights in data—existing works. As prescribed at 227.7105-2(a), use the following clause: Rights in Data—Existing Works (MAR 1979) (a) The term works as used herein... 48 Federal Acquisition Regulations System 3 2010-10-01 2010-10-01 false Rights in data-existing...

  14. Structural Identification Problem

    Directory of Open Access Journals (Sweden)

    Suvorov Aleksei

    2016-01-01

    Full Text Available The identification problem of the existing structures though the Quasi-Newton and its modification, Trust region algorithms is discussed. For the structural problems, which could be represented by means of the mathematical modelling of the finite element code discussed method is extremely useful. The nonlinear minimization problem of the L2 norm for the structures with linear elastic behaviour is solved by using of the Optimization Toolbox of Matlab. The direct and inverse procedures for the composition of the desired function to minimize are illustrated for the spatial 3D truss structure as well as for the problem of plane finite elements. The truss identification problem is solved with 2 and 3 unknown parameters in order to compare the computational efforts and for the graphical purposes. The particular commands of the Matlab codes are present in this paper.

  15. On channel selection and shape co-existence

    International Nuclear Information System (INIS)

    Dracoulis, G.D.

    1993-08-01

    Ambivalence with respect to a favoured shape is emerging as a ubiquitous phenomenon in nuclei. Multiple minima in the nuclear potential well occur because of the delicate balance in nuclei between the long and short-range properties of the nuclear force and the contribution specific particle orbitals make in forcing the nucleus to a decision. Exploration of the dependence of the resulting shape co-existence on particle number and orbital is a prominent area of research. Experimental aspects of spectroscopy studies using heavy ion fusion, evaporation reactions and channel selection are discussed, with focus on shape co-existence in the light Os-Pt-Hg-Pb region. 42 refs., 8 figs

  16. Social Protection Schemes in Pakistan: assessment of existing programs

    Directory of Open Access Journals (Sweden)

    Yu ShuHong

    2017-07-01

    Full Text Available Social protection is regarded as a basic human right guaranteed in several International Covenants and Treaties. The Constitution of Pakistan exclusively stipulates the provision of social security for all citizens of the country. The aim of the study is to explore and evaluate the social protection schemes with regards to its coverage, scope and outreach. The country has number of social security schemes that are being carried out by provincial and federal governments for the welfare of workers like old age benefits, disablement, health and medical facilities. However, these schemes have failed to extend their benefits to home based, part-time, temporary or contract and agricultural workers. This paper attempts to highlight the shortcomings of existing social protection programs that are obstructing their benefit distribution and limiting their outreach. It underlines the challenges faced by the implementing agencies. This paper also suggests some improvements in the structural design of social security mechanism with special focus on the scope, coverage, outreach and effective delivery mechanism. Since, the proper allocation of resources and effective implementation of these schemes can ensure the assistance and welfare of the targeted population.

  17. Spinor structures on homogeneous spaces

    International Nuclear Information System (INIS)

    Lyakhovskii, V.D.; Mudrov, A.I.

    1993-01-01

    For multidimensional models of the interaction of elementary particles, the problem of constructing and classifying spinor fields on homogeneous spaces is exceptionally important. An algebraic criterion for the existence of spinor structures on homogeneous spaces used in multidimensional models is developed. A method of explicit construction of spinor structures is proposed, and its effectiveness is demonstrated in examples. The results are of particular importance for harmonic decomposition of spinor fields

  18. 38 CFR 18.422 - Existing facilities.

    Science.gov (United States)

    2010-07-01

    ... THE CIVIL RIGHTS ACT OF 1964 Nondiscrimination on the Basis of Handicap Accessibility § 18.422 Existing facilities. (a) Accessibility. A recipient shall operate each program or activity to which this... visits, delivery of health, or other social services at alternate accessible sites, alteration of...

  19. Repurposing Existing Material for Performance Support.

    Science.gov (United States)

    Harvey, Francis A.; Nelson, Adam

    1995-01-01

    Presents an overview of performance support systems (PSS), describes their role in promoting productivity in agile organizations, and discusses issues related to developing effective performance support using existing orientation, training, or procedural manuals. Topics include strategic principles of agility, and adding value when incorporating…

  20. 7 CFR 1718.52 - Existing mortgages.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 11 2010-01-01 2010-01-01 false Existing mortgages. 1718.52 Section 1718.52 Agriculture Regulations of the Department of Agriculture (Continued) RURAL UTILITIES SERVICE, DEPARTMENT OF AGRICULTURE LOAN SECURITY DOCUMENTS FOR ELECTRIC BORROWERS Mortgage for Distribution Borrowers § 1718.52...

  1. Discretization of space and time: a slight modification to the Newtonian gravitation which implies the existence of black holes

    OpenAIRE

    Roatta , Luca

    2017-01-01

    Assuming that space and time can only have discrete values, it is shown how deformed space and time cause gravitational attraction, whose law in a discrete context is slightly different from the Newtonian, but to it exactly coincident at large distance. This difference is directly connected to the existence of black holes, which result to have the structure of a hollow sphere.

  2. The science of structural engineering

    CERN Document Server

    Heyman, Jacques

    1999-01-01

    Structures cannot be created without engineering theory, and design rules have existed from the earliest times for building Greek temples, Roman aqueducts and Gothic cathedrals - and later, for steel skyscrapers and the frames for aircraft. This book is, however, not concerned with the description of historical feats, but with the way the structural engineer sets about his business. Galileo, in the seventeenth century, was the first to introduce recognizably modern science into the calculation of structures; he determined the breaking strength of beams. In the eighteenth century engineers move

  3. Existence domains of dust-acoustic solitons and supersolitons

    International Nuclear Information System (INIS)

    Maharaj, S. K.; Bharuthram, R.; Singh, S. V.; Lakhina, G. S.

    2013-01-01

    Using the Sagdeev potential method, the existence of large amplitude dust-acoustic solitons and supersolitons is investigated in a plasma comprising cold negative dust, adiabatic positive dust, Boltzmann electrons, and non-thermal ions. This model supports the existence of positive potential supersolitons in a certain region in parameter space in addition to regular solitons having negative and positive potentials. The lower Mach number limit for supersolitons coincides with the occurrence of double layers whereas the upper limit is imposed by the constraint that the adiabatic positive dust number density must remain real valued. The upper Mach number limits for negative potential (positive potential) solitons coincide with limiting values of the negative (positive) potential for which the negative (positive) dust number density is real valued. Alternatively, the existence of positive potential solitons can terminate when positive potential double layers occur

  4. On the existence and dynamics of braneworld black holes

    International Nuclear Information System (INIS)

    Fitzpatrick, Andrew Liam; Randall, Lisa; Wiseman, Toby

    2006-01-01

    Based on holographic arguments Tanaka and Emparan et al have claimed that large localized static black holes do not exist in the one-brane Randall-Sundrum model. If such black holes are time-dependent as they propose, there are potentially significant phenomenological and theoretical consequences. We revisit the issue, arguing that their reasoning does not take into account the strongly coupled nature of the holographic theory. We claim that static black holes with smooth metrics should indeed exist in these theories, and give a simple example. However, although the existence of such solutions is relevant to exact and numerical solution searches, such static solutions might be dynamically unstable, again leading to time dependence with phenomenological consequences. We explore a plausible instability, suggested by Tanaka, analogous to that of Gregory and Laflamme, but argue that there is no reliable reason at this point to assume it must exist

  5. Virtual existence in contemporary Serbian novel

    Directory of Open Access Journals (Sweden)

    Gordić-Petković Vladislava S.

    2017-01-01

    Full Text Available The paper sets out to explore the perspectives and strategies of virtual existence in contemporary Serbian novel in order to illustrate radical changes in the concept of reality and writers' concern with the fidelity to experience. A new surge of the so-called digital realism emerges simultaneously with the increase of awareness that the line between our digital selves and our real-world selves has become blurred and difficult to explain, while new technologies are required to go beyond what our human senses can encompass and deliver. The fictional realism of the digital age will also commit itself to young or middle-aged individuals that passionately attempt to define their aims and objectives so that they could fit into a newly constructed and acquired concept of reality. This is the case with the protagonists in the novels by Ivančica Đerić, Tamara Jecić and Aleksandar Ilić, all of them questioning both their offline and online identities. Their everyday life in a postmillennial world includes many intersecting empirical and virtual realities: love, career and sex take place in a dimension which ignores geography and physical distance and ultimately alters the concepts of time and space, as well the concepts of privacy and intimacy. The paper intends to examine the ways new digital technologies contribute to representations of reality in the novels of both accomplished and aspiring authors whose novels deal with ways of life amid social networks. The novels we analyzed show that the distinction between the virtual and the real world narrows, as the narratives range from intimate confession in letters and journals to tweets, notes and statuses, introducing verbal and structural experimental practices which involve shifting points of view.

  6. Europe - space for transcultural existence?

    OpenAIRE

    Tamcke, Martin; Janny, de Jong; Klein, Lars; Waal, Margriet

    2013-01-01

    Europe - Space for Transcultural Existence? is the first volume of the new series, Studies in Euroculture, published by Göttingen University Press. The series derives its name from the Erasmus Mundus Master of Excellence Euroculture: Europe in the Wider World, a two year programme offered by a consortium of eight European universities in collaboration with four partner universities outside Europe. This master highlights regional, national and supranational dimensions of the European democrati...

  7. The Greenhouse Effect Does Exist!

    OpenAIRE

    Ebel, Jochen

    2009-01-01

    In particular, without the greenhouse effect, essential features of the atmospheric temperature profile as a function of height cannot be described, i.e., the existence of the tropopause above which we see an almost isothermal temperature curve, whereas beneath it the temperature curve is nearly adiabatic. The relationship between the greenhouse effect and observed temperature curve is explained and the paper by Gerlich and Tscheuschner [arXiv:0707.1161] critically analyzed. Gerlich and Tsche...

  8. A GEOPOLITICAL STAKE: REPUBLIC OF MOLDOVA BETWEEN THE EUROPEAN UNION AND THE EURASIAN UNION

    OpenAIRE

    Mircea-Cristian Ghenghea

    2014-01-01

    This paper presents a comparative analysis of how Estonia, Latvia and Lithuania handled the process of nation-building, finding their self in their new reality which was no longer created and manipulated by the Soviets since their breakaway from the USSR. To do so, this paper suggests an ingenious method of the identity politics analysis which focuses on the importance of the so-called “lieux de mémoire” or “meaning-full places” for people. Monuments and statues are good examples of such plac...

  9. Non-existence criteria for Laurent polynomial first integrals

    Directory of Open Access Journals (Sweden)

    Shaoyun Shi

    2003-01-01

    Full Text Available In this paper we derived some simple criteria for non-existence and partial non-existence Laurent polynomial first integrals for a general nonlinear systems of ordinary differential equations $\\dot x = f(x$, $x \\in \\mathbb{R}^n$ with $f(0 = 0$. We show that if the eigenvalues of the Jacobi matrix of the vector field $f(x$ are $\\mathbb{Z}$-independent, then the system has no nontrivial Laurent polynomial integrals.

  10. Existence of solitary waves in dipolar quantum gases

    KAUST Repository

    Antonelli, Paolo; Sparber, Christof

    2011-01-01

    We study a nonlinear Schrdinger equation arising in the mean field description of dipolar quantum gases. Under the assumption of sufficiently strong dipolar interactions, the existence of standing waves, and hence solitons, is proved together with some of their properties. This gives a rigorous argument for the possible existence of solitary waves in BoseEinstein condensates, which originate solely due to the dipolar interaction between the particles. © 2010 Elsevier B.V. All rights reserved.

  11. The existence and persistence of household financial hardship

    OpenAIRE

    Brown, S.; Ghosh, P.; Taylor, K.

    2012-01-01

    We investigate the existence and persistence of financial hardship at the household level using data from the British Household Panel Survey. Our modelling strategy makes three important contributions to the existing literature on household finances. Firstly, we model nine different types of household financial problems within a joint framework, allowing for correlation in the random effects across the nine equations. Secondly, we develop a dynamic framework in order to model the persistence ...

  12. Existence of solitary waves in dipolar quantum gases

    KAUST Repository

    Antonelli, Paolo

    2011-02-01

    We study a nonlinear Schrdinger equation arising in the mean field description of dipolar quantum gases. Under the assumption of sufficiently strong dipolar interactions, the existence of standing waves, and hence solitons, is proved together with some of their properties. This gives a rigorous argument for the possible existence of solitary waves in BoseEinstein condensates, which originate solely due to the dipolar interaction between the particles. © 2010 Elsevier B.V. All rights reserved.

  13. Experimental Study on Temperature Behavior of SC Structures under Pure Bending

    International Nuclear Information System (INIS)

    Ham, K. W.; Lee, K. J.; Park, D. S.; Jeon, J. H.

    2006-01-01

    SC(Steel plate Concrete) module method uses steel plate instead of reinforcing bar and mold in existing RC structure. Steel plate modules are fabricated in advance, installed and poured with concrete in construction field, so construction period is remarkably shortened by SC module technique. In case of existence of temperature gap between internal and external structure surface such as spent fuel storage pool, thermal stress is taken place and as a result of it, structural strength is deteriorated. In this study, we designed three test specimens and several tests with or without temperature heating were conducted to evaluate temperature behavior of SC structures under pure bending loading condition

  14. Crystalline structure of metals

    International Nuclear Information System (INIS)

    Holas, A.

    1972-01-01

    An attempt is made to find the crystalline structure of metals on the basis of the existing theory of metals. The considerations are limited to the case of free crystals, that is, not subjected to any stresses and with T=0. The energy of the crystal lattice has been defined and the dependence of each term on structures and other properties of metals has been described. The energy has been used to find the values of crystalline structure parameters as the values at which the energy has an absolute minimum. The stability of the structure has been considered in cases of volume changes and shearing deformations. A semiqualitative description has been obtained which explains characteristic properties of one-electron metals. (S.B.)

  15. Robust structural identification via polyhedral template matching

    DEFF Research Database (Denmark)

    Larsen, Peter Mahler; Schmidt, Søren; Schiøtz, Jakob

    2016-01-01

    Successful scientific applications of large-scale molecular dynamics often rely on automated methods for identifying the local crystalline structure of condensed phases. Many existing methods for structural identification, such as common neighbour analysis, rely on interatomic distances (or thres...... is made available under a Free and Open Source Software license....

  16. 49 CFR 223.15 - Requirements for existing passenger cars.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false Requirements for existing passenger cars. 223.15... ADMINISTRATION, DEPARTMENT OF TRANSPORTATION SAFETY GLAZING STANDARDS-LOCOMOTIVES, PASSENGER CARS AND CABOOSES Specific Requirements § 223.15 Requirements for existing passenger cars. (a) Passenger cars built or...

  17. 22 CFR 142.16 - Existing facilities.

    Science.gov (United States)

    2010-04-01

    ... OR ACTIVITIES RECEIVING FEDERAL FINANCIAL ASSISTANCE Accessibility § 142.16 Existing facilities. (a) Accessibility. A recipient shall operate each program or activity to which this part applies so that when each...., telecommunication device for the deaf) redesign of equipment, reassignment of classes or other services to...

  18. Finding Chemical Structures Corresponding to a Set of Coordinates in Chemical Descriptor Space.

    Science.gov (United States)

    Miyao, Tomoyuki; Funatsu, Kimito

    2017-08-01

    When chemical structures are searched based on descriptor values, or descriptors are interpreted based on values, it is important that corresponding chemical structures actually exist. In order to consider the existence of chemical structures located in a specific region in the chemical space, we propose to search them inside training data domains (TDDs), which are dense areas of a training dataset in the chemical space. We investigated TDDs' features using diverse and local datasets, assuming that GDB11 is the chemical universe. These two analyses showed that considering TDDs gives higher chance of finding chemical structures than a random search-based method, and that novel chemical structures actually exist inside TDDs. In addition to those findings, we tested the hypothesis that chemical structures were distributed on the limited areas of chemical space. This hypothesis was confirmed by the fact that distances among chemical structures in several descriptor spaces were much shorter than those among randomly generated coordinates in the training data range. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  19. Travelling Wave Solutions in Multigroup Age-Structured Epidemic Models

    Science.gov (United States)

    Ducrot, Arnaut; Magal, Pierre; Ruan, Shigui

    2010-01-01

    Age-structured epidemic models have been used to describe either the age of individuals or the age of infection of certain diseases and to determine how these characteristics affect the outcomes and consequences of epidemiological processes. Most results on age-structured epidemic models focus on the existence, uniqueness, and convergence to disease equilibria of solutions. In this paper we investigate the existence of travelling wave solutions in a deterministic age-structured model describing the circulation of a disease within a population of multigroups. Individuals of each group are able to move with a random walk which is modelled by the classical Fickian diffusion and are classified into two subclasses, susceptible and infective. A susceptible individual in a given group can be crisscross infected by direct contact with infective individuals of possibly any group. This process of transmission can depend upon the age of the disease of infected individuals. The goal of this paper is to provide sufficient conditions that ensure the existence of travelling wave solutions for the age-structured epidemic model. The case of two population groups is numerically investigated which applies to the crisscross transmission of feline immunodeficiency virus (FIV) and some sexual transmission diseases.

  20. Magnetic monopole interactions: shell structure of meson and baryon states

    International Nuclear Information System (INIS)

    Akers, D.

    1986-01-01

    It is suggested that a low-mass magnetic monopole of Dirac charge g = (137/2)e may be interacting with a c-quark's magnetic dipole moment to produce Zeeman splitting of meson states. The mass M 0 = 2397 MeV of the monopole is in contrast to the 10 16 -GeV monopoles of grand unification theories (GUT). It is shown that shell structure of energy E/sub n/ = M 0 + 1/4nM 0 ... exists for meson states. The presence of symmetric meson states leads to the identification of the shell structure. The possible existence of the 2397-MeV magnetic monopole is shown to quantize quark masses in agreement with calculations of quantum chromodynamics (QCD). From the shell structure of meson states, the existence of two new mesons is predicted: eta(1814 +/- 50 MeV) with I/sup G/(J/sup PC/) = 0 + (0 -+ ) and eta/sub c/ (3907 +/- 100 MeV) with J/sup PC/ = 0 -+ . The presence of shell structure for baryon states is shown

  1. Structure of the subsaturated nuclear matter

    Energy Technology Data Exchange (ETDEWEB)

    Maruyama, Toshiki; Maruyama, Tomoyuki; Chiba, Satoshi; Iwamoto, Akira [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment; Niita, Koji; Oyamatsu, Kazuhiro

    1998-07-01

    Quantum molecular dynamics is applied to study the ground state and excited state properties of nuclear matter at subsaturation densities. The structure of nuclear matter at subsaturation density shows some exotic shapes with variation of the density. However, the structure in our result is rather irregular compared to those of previous works due to the existence of local minimum configurations. (author)

  2. Rozumění pedagogickému jsoucnu: k duchovní obnově pedagogiky a škol. Understanding pedagogical existence: Contribution to the spiritual renewal.

    Directory of Open Access Journals (Sweden)

    Ries Lumír

    2012-09-01

    Full Text Available Similarly to all pedagogical activities, in view of the present situation of man and his world, pedagogical existence is expected to undergo profound transformations. Understanding the nature of the hierarchical structure of pedagogical existence is a potential precondition of these transformations. The hierarchical structure contains the following seven levels: 1. rectification of human circumstances; 2. interpersonal relations; 3. specificity of the spheres of cognition and behaviour; 4. interconnection between the spheres of cognition and behaviour; 5. the cultural, philosophical(ideological potential of cognition and behaviour; 6. learning and experiencing the meaning, higher values and spirituality, 7. deeds, action, behaviour, utilisation. The first, basic level and the top levels, i.e. from the fifth to the seventh, can be consideredpreconditions of desirable transformations within education.

  3. Axioms for quantum mechanics: relativistic causality, retrocausality, and the existence of a classical limit

    Science.gov (United States)

    Rohrlich, Daniel

    Y. Aharonov and A. Shimony both conjectured that two axioms - relativistic causality (``no superluminal signalling'') and nonlocality - so nearly contradict each other that only quantum mechanics reconciles them. Can we indeed derive quantum mechanics, at least in part, from these two axioms? No: ``PR-box'' correlations show that quantum correlations are not the most nonlocal correlations consistent with relativistic causality. Here we replace ``nonlocality'' with ``retrocausality'' and supplement the axioms of relativistic causality and retrocausality with a natural and minimal third axiom: the existence of a classical limit, in which macroscopic observables commute. That is, just as quantum mechanics has a classical limit, so must any generalization of quantum mechanics. In this limit, PR-box correlations violaterelativistic causality. Generalized to all stronger-than-quantum bipartite correlations, this result is a derivation of Tsirelson's bound (a theorem of quantum mechanics) from the three axioms of relativistic causality, retrocausality and the existence of a classical limit. Although the derivation does not assume quantum mechanics, it points to the Hilbert space structure that underlies quantum correlations. I thank the John Templeton Foundation (Project ID 43297) and the Israel Science Foundation (Grant No. 1190/13) for support.

  4. Image-based corrosion recognition for ship steel structures

    Science.gov (United States)

    Ma, Yucong; Yang, Yang; Yao, Yuan; Li, Shengyuan; Zhao, Xuefeng

    2018-03-01

    Ship structures are subjected to corrosion inevitably in service. Existed image-based methods are influenced by the noises in images because they recognize corrosion by extracting features. In this paper, a novel method of image-based corrosion recognition for ship steel structures is proposed. The method utilizes convolutional neural networks (CNN) and will not be affected by noises in images. A CNN used to recognize corrosion was designed through fine-turning an existing CNN architecture and trained by datasets built using lots of images. Combining the trained CNN classifier with a sliding window technique, the corrosion zone in an image can be recognized.

  5. UNCITRAL: Changes to existing law

    OpenAIRE

    Andersson, Joakim

    2008-01-01

    The UNCITRAL Convention on Contracts for the International Carriage of Goods [wholly or partly] by Sea has an ambition of replacing current maritime regimes and expands the application of the Convention to include also multimodal transport. This thesis questions what changes to existing law, in certain areas, the new Convention will bring compared to the current regimes. In the initial part, the thesis provides for a brief background and history of international maritime regulations and focus...

  6. Does Absolute Synonymy exist in Owere-Igbo? | Omego | AFRREV ...

    African Journals Online (AJOL)

    Among Igbo linguistic researchers, determining whether absolute synonymy exists in Owere–Igbo, a dialect of the Igbo language predominantly spoken by the people of Owerri, Imo State, Nigeria, has become a thorny issue. While some linguistic scholars strive to establish that absolute synonymy exists in the lexical ...

  7. Structural convergence under reversible and irreversible monetary unification

    NARCIS (Netherlands)

    Beetsma, R.M.W.J.; Jensen, H.

    2003-01-01

    We explore endogenous monetary unification in the context of a model in which a country with serious structural distortions (and, hence, high inflation) is admitted into a monetary union once its economic structure has converged sufficiently towards that of the existing participants. If unification

  8. Structural convergence under reversible and irreversible monetary unification

    NARCIS (Netherlands)

    Beetsma, R.M.W.J.; Jensen, H.

    1999-01-01

    We explore endogenous monetary unification in the context of a model in which a country with serious structural distortions (and, hence, high inflation) is admitted into a monetary union once its economic structure has converged sufficiently towards that of the existing participants. If unification

  9. Timber in Bridge Structures

    OpenAIRE

    Detkin, Viktoria

    2016-01-01

    The purpose of this final year project was to study the properties of timber as a structural material and the suitability of wood in load bearing members for bridge structures. For a case study, an existing timber bridge was selected. Due to its condition the bridge should be replaced. The design of a new bridge with steel beams holding a glulam deck was made. During the case study the replacement of steel beams by glulam timber ones was discussed. Some calculations were made in order to ...

  10. Pairwise structure alignment specifically tuned for surface pockets and interaction interfaces

    KAUST Repository

    Cui, Xuefeng

    2015-09-09

    To detect and evaluate the similarities between the three-dimensional (3D) structures of two molecules, various kinds of methods have been proposed for the pairwise structure alignment problem [6, 9, 7, 11]. The problem plays important roles when studying the function and the evolution of biological molecules. Recently, pairwise structure alignment methods have been extended and applied on surface pocket structures [10, 3, 5] and interaction interface structures [8, 4]. The results show that, even when there are no global similarities discovered between the global sequences and the global structures, biological molecules or complexes could share similar functions because of well conserved pockets and interfaces. Thus, pairwise pocket and interface structure alignments are promising to unveil such shared functions that cannot be discovered by the well-studied global sequence and global structure alignments. State-of-the-art methods for pairwise pocket and interface structure alignments [4, 5] are direct extensions of the classic pairwise protein structure alignment methods, and thus such methods share a few limitations. First, the goal of the classic protein structure alignment methods is to align single-chain protein structures (i.e., a single fragment of residues connected by peptide bonds). However, we observed that pockets and interfaces tend to consist of tens of extremely short backbone fragments (i.e., three or fewer residues connected by peptide bonds). Thus, existing pocket and interface alignment methods based on the protein structure alignment methods still rely on the existence of long-enough backbone fragments, and the fragmentation issue of pockets and interfaces rises the risk of missing the optimal alignments. Moreover, existing interface structure alignment methods focus on protein-protein interfaces, and require a "blackbox preprocessing" before aligning protein-DNA and protein-RNA interfaces. Therefore, we introduce the PROtein STucture Alignment

  11. Abandonment of the low level outlet structure at the McGregor South Dam

    Energy Technology Data Exchange (ETDEWEB)

    Mack, D.L; Murray, T.K. [Klohn-Crippen Consultants Ltd., Calgary, AB (Canada); Soutar, B.M. [Alberta Transportation, Edmonton, AB (Canada)

    2008-07-01

    The Carseland-Bow River Headworks (CBRH) is a major multi-purpose water delivery system, situated in southern Alberta. It supplies water to 87,000 hectares of agricultural land and several municipalities. The system was originally built starting in 1909. It consists of diversion works on the Bow River, 65 kilometres of canal, and the McGregor and Little Bow reservoirs. In the 1950s, the system was rehabilitated by the Prairie Farm Rehabilitation Administration (PFRA), and Travers Reservoir was added in 1954. In 1973, ownership and operation of the CBRH system was turned over to Alberta Environment. In 2001, Alberta Transportation implemented a major program to rehabilitate and upgrade the CBRH system. This program included increasing the capacity of the canals and structures, and upgrading the dams to meet current dam safety guidelines. The project involved raising the north and south dams, providing an auxiliary spillway to accommodate the probable maximum flood (PMF), and rehabilitating the existing reservoir inlet and low level outlet structures. This paper discussed the abandonment of the existing low level outlet structure located within the south dam. The paper discussed the existing dams and outlet structure as well as the south dam and outlet structure. The abandonment of the existing low level outlet structure was discussed in terms of general construction; demolition; upstream conduits and gatewell; and downstream conduit. Several illustrations and photographs of the dam and the demolition were presented. It was concluded that the in-place abandonment of the existing low level outlet structure at the McGregor South Dam provides significant advantages, including eliminating the need to construct and remove an extensive cofferdam within the reservoir. 6 refs., 2 tabs., 4 figs.

  12. Environmental engineering of navigation infrastructure: a survey of existing practices, challenges, and potential opportunities.

    Science.gov (United States)

    Fredette, Thomas J; Foran, Christy M; Brasfield, Sandra M; Suedel, Burton C

    2012-01-01

    Navigation infrastructure such as channels, jetties, river training structures, and lock-and-dam facilities are primary components of a safe and efficient water transportation system. Planning for such infrastructure has until recently involved efforts to minimize impacts on the environment through a standardized environmental assessment process. More recently, consistent with environmental sustainability concepts, planners have begun to consider how such projects can also be constructed with environmental enhancements. This study examined the existing institutional conditions within the US Army Corps of Engineers and cooperating federal agencies relative to incorporating environmental enhancements into navigation infrastructure projects. The study sought to (1) investigate institutional attitudes towards the environmental enhancement of navigation infrastructure (EENI) concept, (2) identify potential impediments to implementation and solutions to such impediments, (3) identify existing navigation projects designed with the express intent of enhancing environmental benefit in addition to the primary project purpose, (4) identify innovative ideas for increasing environmental benefits for navigation projects, (5) identify needs for additional technical information or research, and (6) identify laws, regulations, and policies that both support and hinder such design features. The principal investigation tool was an Internet-based survey with 53 questions. The survey captured a wide range of perspectives on the EENI concept including ideas, concerns, research needs, and relevant laws and policies. Study recommendations included further promotion of the concept of EENI to planners and designers, documentation of existing projects, initiation of pilot studies on some of the innovative ideas provided through the survey, and development of national goals and interagency agreements to facilitate implementation. Copyright © 2011 SETAC.

  13. Establishing pharmacy operations in a new hospital while transferring existing operations to new ownership.

    Science.gov (United States)

    Crumb, Deborah J

    2010-04-01

    The process of moving pharmacy services and personnel from an existing hospital to a new hospital while maintaining patient care and operations at both facilities is described. The project management structure for the new hospital is described, including the establishment of a departmental coordination team (DCT) for the pharmacy. The purpose of the pharmacy DCT was to plan and coordinate new hospital move-in and pharmacy operations as well as the transition of the existing hospital to new ownership. The use of action item lists and project scorecards kept the project on schedule and on budget. The pharmacy DCT's action item list, which sorted items into four categories (facilities, equipment, operations, and staffing), was reviewed and updated at the weekly meeting of pharmacy leadership and served as the principal guiding document for the pharmacy DCT. Planning and implementation are described for the areas of operations and workflow, staffing, information technology, materials management, accreditation and licensure, and orientation and training. On the transition day, patients under care by physicians employed by the governing organization were transferred to the new facility while patients under care by community physicians remained at the existing facility under new ownership and new administration. Integral to the successful transition were early planning, the provision of adequate training for all employees, and collaboration among organizations, departments, and individuals. A well-coordinated plan resulted in the successful establishment of pharmacy practice in a new hospital and the transition of an operational pharmacy practice and facility to new ownership while maintaining quality patient care.

  14. Does the Kuleshov Effect really Exist?

    DEFF Research Database (Denmark)

    Barratt, Daniel; Cabak Rédei, Anna

    2013-01-01

    with a doll, a dead woman in a coffin, and a bowl of soup; the viewers of the three sequences were reported to have perceived Mozhukin’s face as expressing happiness, sadness, and hunger/thoughtfulness respectively. It is not clear, however, whether or not the socalled “Kuleshov effect” really exists...

  15. Existence region of phases of laminated perovskite-like structre of A/sub 2/B/sub 2/O/sub 7/ composition

    Energy Technology Data Exchange (ETDEWEB)

    Sych, A M; Titov, Yu A [Kievskij Gosudarstvennyj Univ. (Ukrainian SSR)

    1982-06-01

    Generalizing the known data for ferroelectrics of A/sub 2/B/sub 2/O/sub 7/ type (LnTi/sub 2/O/sub 7/, in particular) geometrical conditions of existence of laminated perovskite-like structure are determined: 0.603 A < anti Rsub(Bsup(6)) <= 0.665 A, anti Rsub(Asup(12))/Rsub(Bsup(6)) > 2.045. The geometrical conditions presented are necessary but not sufficient. A supposition is made that phases GaLnTiNbO/sub 7/ (Ln = Pr - Eu) and CaLnTiTaO/sub 7/ (Ln = La - Eu) with laminated perovskite-like structure can be prepared under high pressures.

  16. Existence and attractors of solutions for nonlinear parabolic systems

    Directory of Open Access Journals (Sweden)

    Hamid El Ouardi

    2001-01-01

    Full Text Available We prove existence and asymptotic behaviour results for weak solutions of a mixed problem (S. We also obtain the existence of the global attractor and the regularity for this attractor in $\\left[H^{2}(\\Omega \\right] ^{2}$ and we derive estimates of its Haussdorf and fractal dimensions.

  17. The global existence problem and cosmic censorship in general relativity

    International Nuclear Information System (INIS)

    Moncrief, V.; Eardley, D.M.

    1981-01-01

    Two global existence conjectures for the Einstein equations are formulated and their relevance to the cosmic censorship conjecture discussed. It is argued that the reformulation of the cosmic censorship conjecture as a global existence problem renders it more amenable to direct analytical attack. To demonstrate the facility of this approach the cosmological version of the global existence conjecture is proved for the Gowdy spacetimes on T 3 X R. (author)

  18. 30 CFR 817.84 - Coal mine waste: Impounding structures.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Coal mine waste: Impounding structures. 817.84... ACTIVITIES § 817.84 Coal mine waste: Impounding structures. New and existing impounding structures constructed of coal mine waste or intended to impound coal mine waste shall meet the requirements of § 817.81...

  19. Hidden Structural Codes in Protein Intrinsic Disorder.

    Science.gov (United States)

    Borkosky, Silvia S; Camporeale, Gabriela; Chemes, Lucía B; Risso, Marikena; Noval, María Gabriela; Sánchez, Ignacio E; Alonso, Leonardo G; de Prat Gay, Gonzalo

    2017-10-17

    Intrinsic disorder is a major structural category in biology, accounting for more than 30% of coding regions across the domains of life, yet consists of conformational ensembles in equilibrium, a major challenge in protein chemistry. Anciently evolved papillomavirus genomes constitute an unparalleled case for sequence to structure-function correlation in cases in which there are no folded structures. E7, the major transforming oncoprotein of human papillomaviruses, is a paradigmatic example among the intrinsically disordered proteins. Analysis of a large number of sequences of the same viral protein allowed for the identification of a handful of residues with absolute conservation, scattered along the sequence of its N-terminal intrinsically disordered domain, which intriguingly are mostly leucine residues. Mutation of these led to a pronounced increase in both α-helix and β-sheet structural content, reflected by drastic effects on equilibrium propensities and oligomerization kinetics, and uncovers the existence of local structural elements that oppose canonical folding. These folding relays suggest the existence of yet undefined hidden structural codes behind intrinsic disorder in this model protein. Thus, evolution pinpoints conformational hot spots that could have not been identified by direct experimental methods for analyzing or perturbing the equilibrium of an intrinsically disordered protein ensemble.

  20. Validation of a pre-existing safety climate scale for the Turkish furniture manufacturing industry.

    Science.gov (United States)

    Akyuz, Kadri Cemil; Yildirim, Ibrahim; Gungor, Celal

    2018-03-22

    Understanding the safety climate level is essential to implement a proactive safety program. The objective of this study is to explore the possibility of having a safety climate scale for the Turkish furniture manufacturing industry since there has not been any scale available. The questionnaire recruited 783 subjects. Confirmatory factor analysis (CFA) tested a pre-existing safety scale's fit to the industry. The CFA indicated that the structures of the model present a non-satisfactory fit with the data (χ 2  = 2033.4, df = 314, p ≤ 0.001; root mean square error of approximation = 0.08, normed fit index = 0.65, Tucker-Lewis index = 0.65, comparative fit index = 0.69, parsimony goodness-of-fit index = 0.68). The results suggest that a new scale should be developed and validated to measure the safety climate level in the Turkish furniture manufacturing industry. Due to the hierarchical structure of organizations, future studies should consider a multilevel approach in their exploratory factor analyses while developing a new scale.

  1. THE INSTABILITY AND NON-EXISTENCE OF MULTI-STRANDED LOOPS WHEN DRIVEN BY TRANSVERSE WAVES

    Energy Technology Data Exchange (ETDEWEB)

    Magyar, N.; Van Doorsselaere, T., E-mail: norbert.magyar@wis.kuleuven.be [Centre for Mathematical Plasma Astrophysics (CmPA), KU Leuven, Celestijnenlaan 200B bus 2400, 3001 Leuven (Belgium)

    2016-06-01

    In recent years, omni-present transverse waves have been observed in all layers of the solar atmosphere. Coronal loops are often modeled as a collection of individual strands in order to explain their thermal behavior and appearance. We perform three-dimensional (3D) ideal magnetohydrodynamics simulations to study the effect of a continuous small amplitude transverse footpoint driving on the internal structure of a coronal loop composed of strands. The output is also converted into synthetic images, corresponding to the AIA 171 and 193 Å passbands, using FoMo. We show that the multi-stranded loop ceases to exist in the traditional sense of the word, because the plasma is efficiently mixed perpendicularly to the magnetic field, with the Kelvin–Helmholtz instability acting as the main mechanism. The final product of our simulation is a mixed loop with density structures on a large range of scales, resembling a power-law. Thus, multi-stranded loops are unstable to driving by transverse waves, and this raises strong doubts on the usability and applicability of coronal loop models consisting of independent strands.

  2. Accelerated irradiation growth of zirconium alloys

    International Nuclear Information System (INIS)

    Griffiths, M.; Gilbert, R.W.; Fidleris, V.

    1989-01-01

    This paper discusses how sponge zirconium and Zr-2.5 wt% Nb, Zircaloy, or Excel alloys all exhibit accelerated irradiation growth compared with high-purity crystal-bar zirconium for irradiation temperatures between 550 to 710 K and fluences between 0.1 to 10 x 10 25 n · m -2 (E > 1 MeV). There is generally an incubation period or fluence before the onset of accelerated or breakaway growth, which is dependent on the particular material being irradiated, its metallurgical condition before irradiation, and the irradiation temperature. Transmission electron microscopy has shown that there is a correlation between accelerated irradiation growth and the appearance of c-component vacancy loops on basal planes. Measurements in some specimens indicate that a significant fraction of the strain can be directly attributed to the loops themselves. There is considerable evidence to show that their formation is dependent both on the specimen purity and on the irradiation temperature. Materials that have a high interstitial-solute content contain c-component loops and exhibit high growth rates even at low fluences ( 2 :5 n · m -2 , E > 1 MeV). For sponge zirconium and the Zircaloys, c-component loop formation and the associated acceleration of growth (breakaway) during irradiation occurs because the intrinsic interstitial solute (mainly, oxygen, carbon and nitrogen) in the zirconium matrix is supplemented by interstitial iron, chromium, and nickel from the radiation-induced dissolution of precipitates. (author)

  3. Fire safety assessment of tunnel structures

    DEFF Research Database (Denmark)

    Gkoumas, Konstantinos; Giuliani, Luisa; Petrini, Francesco

    2011-01-01

    .g. structural and non structural, organizational, human behavior). This is even more truth for the fire safety design of such structures. Fire safety in tunnels is challenging because of the particular environment, bearing in mind also that a fire can occur in different phases of the tunnel’s lifecycle. Plans...... for upgrading fire safety provisions and tunnel management are also important for existing tunnels. In this study, following a brief introduction of issues regarding the above mentioned aspects, the structural performance of a steel rib for a tunnel infrastructure subject to fire is assessed by means...

  4. Internal circle uplifts, transversality and stratified G-structures

    Energy Technology Data Exchange (ETDEWEB)

    Babalic, Elena Mirela [Department of Theoretical Physics, National Institute of Physics and Nuclear Engineering,Str. Reactorului no.30, P.O.BOX MG-6, Postcode 077125, Bucharest-Magurele (Romania); Department of Physics, University of Craiova,13 Al. I. Cuza Str., Craiova 200585 (Romania); Lazaroiu, Calin Iuliu [Center for Geometry and Physics, Institute for Basic Science,Pohang 790-784 (Korea, Republic of)

    2015-11-24

    We study stratified G-structures in N=2 compactifications of M-theory on eight-manifolds M using the uplift to the auxiliary nine-manifold M̂=M×S{sup 1}. We show that the cosmooth generalized distribution D̂ on M̂ which arises in this formalism may have pointwise transverse or non-transverse intersection with the pull-back of the tangent bundle of M, a fact which is responsible for the subtle relation between the spinor stabilizers arising on M and M̂ and for the complicated stratified G-structure on M which we uncovered in previous work. We give a direct explanation of the latter in terms of the former and relate explicitly the defining forms of the SU(2) structure which exists on the generic locus U of M to the defining forms of the SU(3) structure which exists on an open subset Û of M̂, thus providing a dictionary between the eight- and nine-dimensional formalisms.

  5. Type-assisted automatic garbage collection for lock-free data structures

    OpenAIRE

    Yang, Albert Mingkun; Wrigstad, Tobias

    2017-01-01

    We introduce Isolde, an automatic garbage collection scheme designed specifically for managing memory in lock-free data structures, such as stacks, lists, maps and queues. Isolde exists as a plug-in memory manager, designed to sit on-top of another memory manager, and use it's allocator and reclaimer (if exists). Isolde treats a lock-free data structure as a logical heap, isolated from the rest of the program. This allows garbage collection outside of Isolde to take place without affecting th...

  6. Global existence of small solutions to semilinear Schroedinger equations

    International Nuclear Information System (INIS)

    Chihara, Hiroyuki

    1996-01-01

    We present global existence theorem for semilinear Schrodinger equations. In general, Schrodinger-type equations do not admit the classical energy estimates. To avoid this difficulty, we use S. Doi's method for linear Schrodinger-type equations. Combining his method and L p -L q estimates, we prove the global existence of solutions with small initial data

  7. Kinetic Dissection of the Pre-existing Conformational Equilibrium in the Trypsin Fold*

    Science.gov (United States)

    Vogt, Austin D.; Chakraborty, Pradipta; Di Cera, Enrico

    2015-01-01

    Structural biology has recently documented the conformational plasticity of the trypsin fold for both the protease and zymogen in terms of a pre-existing equilibrium between closed (E*) and open (E) forms of the active site region. How such plasticity is manifested in solution and affects ligand recognition by the protease and zymogen is poorly understood in quantitative terms. Here we dissect the E*-E equilibrium with stopped-flow kinetics in the presence of excess ligand or macromolecule. Using the clotting protease thrombin and its zymogen precursor prethrombin-2 as relevant models we resolve the relative distribution of the E* and E forms and the underlying kinetic rates for their interconversion. In the case of thrombin, the E* and E forms are distributed in a 1:4 ratio and interconvert on a time scale of 45 ms. In the case of prethrombin-2, the equilibrium is shifted strongly (10:1 ratio) in favor of the closed E* form and unfolds over a faster time scale of 4.5 ms. The distribution of E* and E forms observed for thrombin and prethrombin-2 indicates that zymogen activation is linked to a significant shift in the pre-existing equilibrium between closed and open conformations that facilitates ligand binding to the active site. These findings broaden our mechanistic understanding of how conformational transitions control ligand recognition by thrombin and its zymogen precursor prethrombin-2 and have direct relevance to other members of the trypsin fold. PMID:26216877

  8. Mechanism of structural type formation of rare earth polychalcogenides

    International Nuclear Information System (INIS)

    Kuz'micheva, G.M.; Eliseev, A.A.; Khalina, S.Yu.

    1981-01-01

    It proved to be possible to obtain the structural motives not only of all the known polychalcogenides of rare earth elements but to forecast compounds not yet existing on the basis of two initial structural motives. All the structural motives can be divided into superstructures and polytypes as to the mechanism of their formation [ru

  9. Hydrological structure and biological productivity of the tropical Indian Ocean

    Digital Repository Service at National Institute of Oceanography (India)

    Muraleedharan, U.D.; Muraleedharan, P.M.

    Hydrological structure analyses of regions in the tropical Atlantic Ocean have consistently revealed the existence of a typical tropical structure characterized by a nitrate-depleted mixed layer above the thermocline. The important biological...

  10. Reality of the fundamental topological structure in the QCD vacuum

    International Nuclear Information System (INIS)

    Alexandru, Andrei; Horvath, Ivan; Zhang Jianbo

    2005-01-01

    Long-range order of a specific kind has recently been found directly in configurations dominating the regularized QCD path integral. In particular, a low-dimensional global structure was identified in typical space-time distributions of topological charge defined via the overlap Dirac matrix. The presence of the order has been concluded from the fact that the structure disappears after random permutation of position coordinates in measured densities. Here we complete the argument for the reality of this structure (namely the conjecture that its existence is a consequence of QCD dynamics and not an artifact of the overlap-based definition of lattice topological field) by showing that the structure ceases to exist after randomizing the space-time coordinates of the underlying gauge field. This implies that the long-range order present in the overlap-based topological density is indeed a manifestation of the QCD vacuum, and that the notion of the fundamental structure (structure involving relevant features at all scales) is viable

  11. Fabrication and characterization of woodpile structures

    DEFF Research Database (Denmark)

    Zalkovskij, Maksim; Malureanu, Radu; Andryieuski, Andrei

    2011-01-01

    In this paper we present the whole fabrication and characterization cycle for obtaining 3D metal-dielectric woodpile structures. The optical properties of these structures have been measured using different setups showing the need of considering e.g. border effects when planning their use in real......-life devices. It was found that the behavior of the structures close to the edge is very different from the one in the middle. The existence of special features in the former spectra still needs to be completely understood and explained....

  12. CASS Ferrite and Grain Structure Relationship

    Energy Technology Data Exchange (ETDEWEB)

    Ruud, Clayton O. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Ramuhalli, Pradeep [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Meyer, Ryan M. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Diaz, Aaron A. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Anderson, Michael T. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

    2016-07-13

    This document summarizes the results of research conducted at Pacific Northwest National Laboratory (PNNL) to determine whether, based on experimental measurements, a correlation existed between grain structure in cast austenitic stainless steel (CASS) piping and ferrite content of the casting alloy. The motivation for this research lies in the fact that ultrasonic testing (UT) is strongly influenced by CASS grain structure; knowledge of this grain structure may help improve the ability to interpret UT responses, thereby improving the overall reliability of UT inspections of CASS components.

  13. THE RELIABILITY ANALYSIS OF EXISTING REINFORCED CONCRETE PILES IN PERMAFROST REGIONS

    Directory of Open Access Journals (Sweden)

    Vladimir S. Utkin

    2017-06-01

    Full Text Available The article describes the general problem of safe operation of buildings and structures with the dynamics of permafrost in Russia and other countries. The global warming on Earth will lead to global disasters such as failures of buildings and structures. The main reason of these failures will be a reduction of bearing capacity and the reliability of foundations. It is necessary to organize the observations (monitoring for the process of reducing the bearing capacity of foundations to prevent such accidents and reduce negative consequences, to development of preventive measures and operational methods for the piles reliability analysis. The main load-bearing elements of the foundation are reinforced concrete piles and frozen ground. Reinforced concrete piles have a tendency to decrease the bearing capacity and reliability of the upper (aerial part and the part in the soil. The article discusses the problem of reliability analysis of existing reinforced concrete piles in upper part in permafrost regions by the reason of pile degradation in the contact zone of seasonal thawing and freezing soil. The evaluation of the probability of failure is important in itself, but also it important for the reliability of foundation: consisting of piles and frozen soil. Authors offers the methods for reliability analysis of upper part of reinforced concrete piles in the contact zone with seasonally thawed soil under different number of random variables (fuzzy variables in the design mathematical model of a limit state by the strength criterion.

  14. An Owen-type value for games with two-level communication structures

    NARCIS (Netherlands)

    van den Brink, René; Khmelnitskaya, Anna Borisovna; van der Laan, Gerard

    We introduce an Owen-type value for games with two-level communication structure, which is a structure where the players are partitioned into a coalition structure such that there exists restricted communication between as well as within the a priori unions of the coalition structure. Both types of

  15. Visualization of RNA structure models within the Integrative Genomics Viewer.

    Science.gov (United States)

    Busan, Steven; Weeks, Kevin M

    2017-07-01

    Analyses of the interrelationships between RNA structure and function are increasingly important components of genomic studies. The SHAPE-MaP strategy enables accurate RNA structure probing and realistic structure modeling of kilobase-length noncoding RNAs and mRNAs. Existing tools for visualizing RNA structure models are not suitable for efficient analysis of long, structurally heterogeneous RNAs. In addition, structure models are often advantageously interpreted in the context of other experimental data and gene annotation information, for which few tools currently exist. We have developed a module within the widely used and well supported open-source Integrative Genomics Viewer (IGV) that allows visualization of SHAPE and other chemical probing data, including raw reactivities, data-driven structural entropies, and data-constrained base-pair secondary structure models, in context with linear genomic data tracks. We illustrate the usefulness of visualizing RNA structure in the IGV by exploring structure models for a large viral RNA genome, comparing bacterial mRNA structure in cells with its structure under cell- and protein-free conditions, and comparing a noncoding RNA structure modeled using SHAPE data with a base-pairing model inferred through sequence covariation analysis. © 2017 Busan and Weeks; Published by Cold Spring Harbor Laboratory Press for the RNA Society.

  16. Thermal and structural properties of zinc modified tellurite based glasses

    Science.gov (United States)

    Kundu, R. S.; Dhankhar, Sunil; Punia, R.; Dult, Meenakshi; Kishore, N.

    2016-05-01

    Glass system 60 TeO2 - 10 B2O3-(30-x) Bi2O3-x ZnO with mole fraction x = 10, 15, 20, 25 and 30 were synthesized by conventional melt quenching technique under controlled atmospheric conditions. The glass transition temperature (Tg) has been determined using differential scanning Calorimetry (DSC) and its value is observed to increase with increase in ZnO content. This increase may be due to the increase in the concentration of the bridging oxygen (BO) atoms. IR and Raman spectra of the present glass system indicate that ZnO acts as network modifier and exists in ZnO4 units. TeO2 exists as TeO3, TeO4, and TeO3+1 structural units. Bismuth plays the role of network modifier with BiO6 octahedral structural units whereas B2O3 exists in the form of BO3 trigonal and BO4 tetrahedral structural units.

  17. New structure for accelerating heavy ions; Une nouvelle structure acceleratrice d'ions lourds

    Energy Technology Data Exchange (ETDEWEB)

    Pottier, J [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1969-06-01

    A new type of accelerating structure is described which is particular suited to heavy ions (high wavelength, high shunt impedance, small size). Its properties are analyzed and compared to those of other structures (more particularly the lines). It is shown that a mode of operation exists of which the shunt impedance in the station mode has 80 per cent of its value for the progressive mode. Finally results are given obtained with a small experimental apparatus which uses this structure. (author) [French] On decrit un nouveau type de structure acceleratrice, particulierement appropriee aux ions lourds (grande longueur d'onde, forte impedance-shunt, faibles dimensions). Ses proprietes sont analysees et comparees a celles d'autres structures (plus particulierement les lignes). On met en evidence un mode de fonctionnement pour lequel l'impedance shunt en regime stationnaire vaut 80 pour cent de l'impedance shunt en regime progressif. Enfin on decrit les resultats obtenus a l'aide d'une petite machine experimentale mettant en oeuvre cette structure. (auteur)

  18. EXISTENCE OF POSITIVE SOLUTIONS FOR AN ELASTIC CURVED BEAM EQUATION

    Directory of Open Access Journals (Sweden)

    Béla Kovacs

    2017-06-01

    Full Text Available This paper investigates the existence of positive solutions for a sixth-order differential equations. By using the Leggett-Williams fixed point theorem we give some new existence results.

  19. Erosion of divertor materials in simulation experiments of ITEP thermonuclear reactor operation

    International Nuclear Information System (INIS)

    Guseva, M.I.; Gureev, V.M.; Danelyan, L.S.; Kolbasov, B.N.; Korshunov, S.N.; Martynenko, Yu.V.; Petrov, V.B.; Stolyarova, V.G.; Khripunov, B.I.; Vasil'ev, V.I.; Strunnikov, V.M.

    2004-01-01

    The tungsten sputtering by the deuterium ions with the energy of 5 eV at the temperature of 1470 K with the sputtering coefficient of 1.5 x 10 -4 at/ion is identified. Comparison of the erosion degree of various W types and W + C coatings on W is carried out in the experiments on simulating the plasma break-away; W drops distribution by the diameters, depending on the collector drops position, is studied. W(111) tungsten is characterized by the minimal erosion and W-10% Re tungsten - by the maximum one [ru

  20. Nuclear matrix and structural and functional compartmentalization of the eucaryotic cell nucleus.

    Science.gov (United States)

    Razin, S V; Borunova, V V; Iarovaia, O V; Vassetzky, Y S

    2014-07-01

    Becoming popular at the end of the 20th century, the concept of the nuclear matrix implies the existence of a nuclear skeleton that organizes functional elements in the cell nucleus. This review presents a critical analysis of the results obtained in the study of nuclear matrix in the light of current views on the organization of the cell nucleus. Numerous studies of nuclear matrix have failed to provide evidence of the existence of such a structure. Moreover, the existence of a filamentous structure that supports the nuclear compartmentalization appears to be unnecessary, since this function is performed by the folded genome itself.

  1. Oral insulin delivery: existing barriers and current counter-strategies.

    Science.gov (United States)

    Gedawy, Ahmed; Martinez, Jorge; Al-Salami, Hani; Dass, Crispin R

    2018-02-01

    The chronic and progressive nature of diabetes is usually associated with micro- and macrovascular complications where failure of pancreatic β-cell function and a general condition of hyperglycaemia is created. One possible factor is failure of the patient to comply with and adhere to the prescribed insulin due to the inconvenient administration route. This review summarizes the rationale for oral insulin administration, existing barriers and some counter-strategies trialled. Oral insulin mimics the physiology of endogenous insulin secreted by pancreas. Following the intestinal absorption of oral insulin, it reaches the liver at high concentration via the portal vein. Oral insulin on the other hand has the potential to protect pancreatic β-cells from autoimmune destruction. Structural modification, targeting a particular tissue/receptor, and the use of innovative pharmaceutical formulations such as nanoparticles represent strategies introduced to improve oral insulin bioavailability. They showed promising results in overcoming the hurdles facing oral insulin delivery, although delivery is far from ideal. The use of advanced pharmaceutical technologies and further research in particulate carrier system delivery predominantly nanoparticle utilization would offer useful tools in delivering insulin via the oral route which in turn would potentially improve diabetic patient compliance to insulin and the overall management of diabetes. © 2017 Royal Pharmaceutical Society.

  2. Analisys of subcultures existence in a european multinational company stablished in Brazil Análise da existência de subculturas em uma multinacional européia sediada no Brasil

    Directory of Open Access Journals (Sweden)

    André Cardoso

    2010-02-01

    Full Text Available Corporate culture is one of the main sources of organizational identity. In large corporations, the existence of a "backbone" seems to be evident; however, the manifestation of subcultures is a natural phenomenon due to the complexity of operations and diversity of people who are part of the organizational system. This article tries to identify the existence of subcultures in a European multinational organization installed in Brazil. The selected method, case study research, was based on the problematic of identifying and comparing the main cultural elements in Sales and Service departments of this organization. This paper aimed to compare main values, artifacts, leadership, decision making process and communication in both departments, using empirical investigation compounded by deep structured interviews and non-participant observations. The main contributions raise up that each department show its own way of acting, based on its own meanings and urgency sense. The theoretical basis for this study was Schein's concept of organizational culture (SCHEIN, 1992; 2007 and the three cultural perspectives defined by Martin (1999.A cultura é uma das principais fontes da identidade organizacional. Em grandes corporações, a existência de uma "espinha dorsal" parece ser evidente, entretanto, a manifestação de subculturas é um fenômeno natural devido à complexidade das operações e diversidade de sujeitos que fazem parte do sistema organizacional. Este artigo procura identificar a existência de subculturas em uma organização multinacional de origem européia sediada no Brasil. O método escolhido, estudo de caso qualitativo, foi amparado na problemática de identificar e comparar os principais elementos culturais dos departamentos de vendas e serviços desta organização. Este trabalho se propôs comparar os principais valores, artefatos, liderança, processo de tomada de decisão e comunicação destes dois departamentos, a partir da

  3. The existence of trajectories joining critical points

    International Nuclear Information System (INIS)

    Yu Shuxiang.

    1985-01-01

    In this paper, using the notion of an isolating block and the concept of canonical regions, three existence criteria of trajectories connecting a pair of critical points of planar differential equations are given. (author)

  4. Method and refrigerants for replacing existing refrigerants in centrifugal compressors

    International Nuclear Information System (INIS)

    Kopko, W.L.

    1991-01-01

    This patent describes a method for replacing an existing refrigerant in a centrifugal compressor. It comprises selecting a desired impeller Mach number for the centrifugal compressor; selecting a base refrigerant constituent; combining at least one additive refrigerant constituent with the base refrigerant constituent to form a replacement refrigerant having at least one physical or chemical property different from the existing refrigerant and substantially providing the desired impeller Mach number in the centrifugal compressor; and replacing the existing refrigerant with the replacement refrigerant

  5. THE FLAT TAX - A COMPARATIVE STUDY OF THE EXISTING MODELS

    Directory of Open Access Journals (Sweden)

    Schiau (Macavei Laura - Liana

    2011-07-01

    taxation but they have several tax rates for different types of income. Analyzing the flat tax jurisdiction we concluded that none of the existing models is a true flat tax as designed by Hall and Rabushka. The study is important given the fact that it can provide useful information for future studies in connecting the effects generated by the adoption of flat tax with the design of the system. This can give intelligence for the exiting models in correcting and improving their features in order to become more efficient. This can also provide precious design information for the jurisdictions desirous of implementing flat tax systems. The added value of this paperwork consists in the determination of the main features of the existing flat tax systems in relation with the theoretical system designed by Hall and Rabushka and in the fact that it provides precious structured information for future studies allowing to connect the effects of the flat fiscal model with its characteristics.

  6. Possible existence of wormholes in the central regions of halos

    Energy Technology Data Exchange (ETDEWEB)

    Rahaman, Farook, E-mail: rahaman@iucaa.ernet.in [Department of Mathematics, Jadavpur University, Kolkata 700032, West Bengal (India); Salucci, P., E-mail: salucci@sissa.it [SISSA, International School for Advanced Studies, Via Bonomea 265, 34136, Trieste (Italy); INFN, Sezione di Trieste, Via Valerio 2, 34127, Trieste (Italy); Kuhfittig, P.K.F., E-mail: kuhfitti@msoe.edu [Department of Mathematics, Milwaukee School of Engineering, Milwaukee, WI 53202-3109 (United States); Ray, Saibal, E-mail: saibal@iucaa.ernet.in [Department of Physics, Government College of Engineering and Ceramic Technology, Kolkata 700010, West Bengal (India); Rahaman, Mosiur, E-mail: mosiurju@gmail.com [Department of Mathematics, Meghnad Saha Institute of Technology, Kolkata 700150 (India)

    2014-11-15

    An earlier study (Rahaman, et al., 2014 and Kuhfittig, 2014) has demonstrated the possible existence of wormholes in the outer regions of the galactic halo, based on the Navarro–Frenk–White (NFW) density profile. This paper uses the Universal Rotation Curve (URC) dark matter model to obtain analogous results for the central parts of the halo. This result is an important compliment to the earlier result, thereby confirming the possible existence of wormholes in most of the spiral galaxies. - Highlights: • Earlier we showed possible existence of wormholes in the outer regions of halo. • We obtain here analogous results for the central parts of the galactic halo. • Our result is an important compliment to the earlier result. • This confirms possible existence of wormholes in most of the spiral galaxies.

  7. Equilibrium with arbitrary market structure

    DEFF Research Database (Denmark)

    Grodal, Birgit; Vind, Karl

    2005-01-01

    . The complete market predicted by this theory is clearly unrealistic, and Radner [10] formulated and proved existence of equilibrium in a multiperiod model with incomplete markets. In this paper the Radner result is extended. Radner assumed a specific structure of markets, independence of preferences...

  8. Proximity effect in normal metal-multiband superconductor hybrid structures

    NARCIS (Netherlands)

    Brinkman, Alexander; Golubov, Alexandre Avraamovitch; Kupriyanov, M. Yu

    2004-01-01

    A theory of the proximity effect in normal metal¿multiband superconductor hybrid structures is formulated within the quasiclassical Green's function formalism. The quasiclassical boundary conditions for multiband hybrid structures are derived in the dirty limit. It is shown that the existence of

  9. Selfsimilar time dependent shock structures

    International Nuclear Information System (INIS)

    Beck, R.; Drury, L.O.

    1985-01-01

    Diffusive shock acceleration as an astrophysical mechanism for accelerating charged particles has the advantage of being highly efficient. This means however that the theory is of necessity nonlinear; the reaction of the accelerated particles on the shock structure and the acceleration process must be self-consistently included in any attempt to develop a complete theory of diffusive shock acceleration. Considerable effort has been invested in attempting, at least partially, to do this and it has become clear that in general either the maximum particle energy must be restricted by introducing additional loss processes into the problem or the acceleration must be treated as a time dependent problem (Drury, 1984). It is concluded that stationary modified shock structures can only exist for strong shocks if additional loss processes limit the maximum energy a particle can attain. This is certainly possible and if it occurs the energy loss from the shock will lead to much greater shock compressions. It is however equally possible that no such processes exist and we must then ask what sort of nonstationary shock structure develops. The same argument which excludes stationary structures also rules out periodic solutions and indeed any solution where the width of the shock remains bounded. It follows that the width of the shock must increase secularly with time and it is natural to examine the possibility of selfsimilar time dependent solutions

  10. Selfsimilar time dependent shock structures

    Science.gov (United States)

    Beck, R.; Drury, L. O.

    1985-01-01

    Diffusive shock acceleration as an astrophysical mechanism for accelerating charged particles has the advantage of being highly efficient. This means however that the theory is of necessity nonlinear; the reaction of the accelerated particles on the shock structure and the acceleration process must be self-consistently included in any attempt to develop a complete theory of diffusive shock acceleration. Considerable effort has been invested in attempting, at least partially, to do this and it has become clear that in general either the maximum particle energy must be restricted by introducing additional loss processes into the problem or the acceleration must be treated as a time dependent problem (Drury, 1984). It is concluded that stationary modified shock structures can only exist for strong shocks if additional loss processes limit the maximum energy a particle can attain. This is certainly possible and if it occurs the energy loss from the shock will lead to much greater shock compressions. It is however equally possible that no such processes exist and we must then ask what sort of nonstationary shock structure develops. The ame argument which excludes stationary structures also rules out periodic solutions and indeed any solution where the width of the shock remains bounded. It follows that the width of the shock must increase secularly with time and it is natural to examine the possibility of selfsimilar time dependent solutions.

  11. Expansion potential for existing nuclear power station sites

    Energy Technology Data Exchange (ETDEWEB)

    Cope, D. F.; Bauman, H. F.

    1977-09-26

    This report is a preliminary analysis of the expansion potential of the existing nuclear power sites, in particular their potential for development into nuclear energy centers (NECs) of 10 (GW(e) or greater. The analysis is based primarily on matching the most important physical characteristics of a site against the dominating site criteria. Sites reviewed consist mainly of those in the 1974 through 1976 ERDA Nuclear Power Stations listings without regard to the present status of reactor construction plans. Also a small number of potential NEC sites that are not associated with existing power stations were reviewed. Each site was categorized in terms of its potential as: a dispersed site of 5 GW(e) or less; a mini-NEC of 5 to 10 GW(e); NECs of 10 to 20 GW(e); and large NECs of more than 20 GW(e). The sites were categorized on their ultimate potential without regard to political considerations that might restrain their development. The analysis indicates that nearly 40 percent of existing sites have potential for expansion to nuclear energy centers.

  12. On the existence of perturbed Robertson-Walker universes

    International Nuclear Information System (INIS)

    D'Eath, P.D.

    1976-01-01

    Solutions of the full nonlinear field equations of general relativity near the Robertson-Walker universes are examined, together with their relation to linearized perturbations. A method due to Choquet-Bruhat and Deser is used to prove existence theorems for solutions near Robertson-Walker constraint data of the constraint equations on a spacelike hypersurface. These theorems allow one to regard the matter fluctuations as independent quantities, ranging over certain function spaces. In the k=-1 case the existence theory describes perturbations which may vary within uniform bounds throughout space. When k=+1 a modification of the method leads to a theorem which clarifies some unusual features of these constraint perturbations. The k=0 existence theorem refers only to perturbations which die away at large distances. The connection between linearized constraint solutions and solutions of the full constraints is discussed. For k= +- 1 backgrounds, solutions of the linearized constraints are analyzed using transverse-traceless decompositions of symmetric tensors. Finally the time-evolution of perturbed constraint data and the validity of linearized perturbation theory for Robertson-Walker universes are considered

  13. Expansion potential for existing nuclear power station sites

    International Nuclear Information System (INIS)

    Cope, D.F.; Bauman, H.F.

    1977-01-01

    This report is a preliminary analysis of the expansion potential of the existing nuclear power sites, in particular their potential for development into nuclear energy centers (NECs) of 10 (GW(e) or greater. The analysis is based primarily on matching the most important physical characteristics of a site against the dominating site criteria. Sites reviewed consist mainly of those in the 1974 through 1976 ERDA Nuclear Power Stations listings without regard to the present status of reactor construction plans. Also a small number of potential NEC sites that are not associated with existing power stations were reviewed. Each site was categorized in terms of its potential as: a dispersed site of 5 GW(e) or less; a mini-NEC of 5 to 10 GW(e); NECs of 10 to 20 GW(e); and large NECs of more than 20 GW(e). The sites were categorized on their ultimate potential without regard to political considerations that might restrain their development. The analysis indicates that nearly 40 percent of existing sites have potential for expansion to nuclear energy centers

  14. O Ponto G Existe?

    Directory of Open Access Journals (Sweden)

    Carlos Alexandre Molina Noccioli

    2016-07-01

    Full Text Available Este trabalho busca analisar o tratamento linguístico-discursivo das informações acerca de um tópicotemático tradicionalmente visto como tabu, relacionado a questões sexuais, na notícia O ponto G existe?, publicada em 2008, na revista brasileira Superinteressante, destacando-se como o conhecimento em questão é representado socialmente ao se considerar a linha editorial da revista. A notícia caracteriza-se como um campo fértil para a análise das estratégias divulgativas, já que atrai, inclusive pelas escolhas temáticas, a curiosidade dos leitores. Imbuído de um tema excêntrico, o texto consegue angariar um público jovem interessado em discussões polêmicas relacionadas ao seu universo.

  15. Applicability Problem in Optimum Reinforced Concrete Structures Design

    Directory of Open Access Journals (Sweden)

    Ashara Assedeq

    2016-01-01

    Full Text Available Optimum reinforced concrete structures design is very complex problem, not only considering exactness of calculus but also because of questionable applicability of existing methods in practice. This paper presents the main theoretical mathematical and physical features of the problem formulation as well as the review and analysis of existing methods and solutions considering their exactness and applicability.

  16. Using existing case-mix methods to fund trauma cases.

    Science.gov (United States)

    Monakova, Julia; Blais, Irene; Botz, Charles; Chechulin, Yuriy; Picciano, Gino; Basinski, Antoni

    2010-01-01

    Policymakers frequently face the need to increase funding in isolated and frequently heterogeneous (clinically and in terms of resource consumption) patient subpopulations. This article presents a methodologic solution for testing the appropriateness of using existing grouping and weighting methodologies for funding subsets of patients in the scenario where a case-mix approach is preferable to a flat-rate based payment system. Using as an example the subpopulation of trauma cases of Ontario lead trauma hospitals, the statistical techniques of linear and nonlinear regression models, regression trees, and spline models were applied to examine the fit of the existing case-mix groups and reference weights for the trauma cases. The analyses demonstrated that for funding Ontario trauma cases, the existing case-mix systems can form the basis for rational and equitable hospital funding, decreasing the need to develop a different grouper for this subset of patients. This study confirmed that Injury Severity Score is a poor predictor of costs for trauma patients. Although our analysis used the Canadian case-mix classification system and cost weights, the demonstrated concept of using existing case-mix systems to develop funding rates for specific subsets of patient populations may be applicable internationally.

  17. The Relationships of Subparallel Synthetic Faults and Pre-existing Structures in the Central Malawi Rift

    Science.gov (United States)

    Johnson, S.; Mendez, K.; Beresh, S. C. M.; Mynatt, W. G.; Elifritz, E. A.; Laó-Dávila, D. A.; Atekwana, E. A.; Abdelsalam, M. G.; Chindandali, P. R. N.; Chisenga, C.; Gondwe, S.; Mkumbura, M.; Kalaguluka, D.; Kalindekafe, L.; Salima, J.

    2017-12-01

    The objective of our research is to explore the evolution of synthetic fault systems in continental rifts. It has been suggested that during the rifting process border faults may become locked and strain is then accommodated within the hanging wall. The Malawi Rift provides an opportunity to study the evolution of these faults within a young (8 Ma), active and magma-poor continental rift. Two faults in central Malawi may show the transference of strain into the hanging wall. These faults are the older Chirobwe-Ntcheu with a length of 115 km and a scarp height of 300-1000 m and the younger Bilila-Mtakataka with a length of 130 km and a scarp height of 4-320 m. We used high-resolution aeromagnetic data and 30m resolution Shuttle Radar Topography Mission (SRTM) digital elevation models (DEM) to provide a 3D spatial characterization of the fault system. Additionally 10cm resolution DEMs were created using unmanned aerial system (UAS) derived aerial photography and Structure from Motion to document the regional Precambrian foliation and joint patterns. Moreover, displacement profiles where extracted from the SRTM-DEM data to compare the segmentation and linkage of the outer and inner faults. Our preliminary results show that the strike of each fault is approximately NW-SE which follows the strike of the Precambrian fabric. The magnetic fabric has a strike of NW-SE in the south changing to NE-SW in the north suggesting that the faults are controlled in part by an inherited Precambrian fabric. The displacement profile of the inner Bilila-Mtakataka fault is asymmetric and displays five fault segments supporting the interpretation that this is a relatively young fault. The expected results of this study are information about segmentation and displacement of each fault and their relationship to one another. The results from the aeromagnetic data utilizing Source Parameter Imaging to produce an approximate depth to basement which will support the displacement profiles derived

  18. Structural Dynamic Analyses And Test Predictions For Spacecraft Structures With Non-Linearities

    Science.gov (United States)

    Vergniaud, Jean-Baptiste; Soula, Laurent; Newerla, Alfred

    2012-07-01

    The overall objective of the mechanical development and verification process is to ensure that the spacecraft structure is able to sustain the mechanical environments encountered during launch. In general the spacecraft structures are a-priori assumed to behave linear, i.e. the responses to a static load or dynamic excitation, respectively, will increase or decrease proportionally to the amplitude of the load or excitation induced. However, past experiences have shown that various non-linearities might exist in spacecraft structures and the consequences of their dynamic effects can significantly affect the development and verification process. Current processes are mainly adapted to linear spacecraft structure behaviour. No clear rules exist for dealing with major structure non-linearities. They are handled outside the process by individual analysis and margin policy, and analyses after tests to justify the CLA coverage. Non-linearities can primarily affect the current spacecraft development and verification process on two aspects. Prediction of flights loads by launcher/satellite coupled loads analyses (CLA): only linear satellite models are delivered for performing CLA and no well-established rules exist how to properly linearize a model when non- linearities are present. The potential impact of the linearization on the results of the CLA has not yet been properly analyzed. There are thus difficulties to assess that CLA results will cover actual flight levels. Management of satellite verification tests: the CLA results generated with a linear satellite FEM are assumed flight representative. If the internal non- linearities are present in the tested satellite then there might be difficulties to determine which input level must be passed to cover satellite internal loads. The non-linear behaviour can also disturb the shaker control, putting the satellite at risk by potentially imposing too high levels. This paper presents the results of a test campaign performed in

  19. Deep learning-based subdivision approach for large scale macromolecules structure recovery from electron cryo tomograms.

    Science.gov (United States)

    Xu, Min; Chai, Xiaoqi; Muthakana, Hariank; Liang, Xiaodan; Yang, Ge; Zeev-Ben-Mordehai, Tzviya; Xing, Eric P

    2017-07-15

    Cellular Electron CryoTomography (CECT) enables 3D visualization of cellular organization at near-native state and in sub-molecular resolution, making it a powerful tool for analyzing structures of macromolecular complexes and their spatial organizations inside single cells. However, high degree of structural complexity together with practical imaging limitations makes the systematic de novo discovery of structures within cells challenging. It would likely require averaging and classifying millions of subtomograms potentially containing hundreds of highly heterogeneous structural classes. Although it is no longer difficult to acquire CECT data containing such amount of subtomograms due to advances in data acquisition automation, existing computational approaches have very limited scalability or discrimination ability, making them incapable of processing such amount of data. To complement existing approaches, in this article we propose a new approach for subdividing subtomograms into smaller but relatively homogeneous subsets. The structures in these subsets can then be separately recovered using existing computation intensive methods. Our approach is based on supervised structural feature extraction using deep learning, in combination with unsupervised clustering and reference-free classification. Our experiments show that, compared with existing unsupervised rotation invariant feature and pose-normalization based approaches, our new approach achieves significant improvements in both discrimination ability and scalability. More importantly, our new approach is able to discover new structural classes and recover structures that do not exist in training data. Source code freely available at http://www.cs.cmu.edu/∼mxu1/software . mxu1@cs.cmu.edu. Supplementary data are available at Bioinformatics online. © The Author 2017. Published by Oxford University Press. All rights reserved. For Permissions, please e-mail: journals.permissions@oup.com

  20. Inhibition of existing denitrification enzyme activity by chloramphenicol

    Science.gov (United States)

    Brooks, M.H.; Smith, R.L.; Macalady, D.L.

    1992-01-01

    Chloramphenicol completely inhibited the activity of existing denitrification enzymes in acetylene-block incubations with (i) sediments from a nitrate-contaminated aquifer and (ii) a continuous culture of denitrifying groundwater bacteria. Control flasks with no antibiotic produced significant amounts of nitrous oxide in the same time period. Amendment with chloramphenicol after nitrous oxide production had begun resulted in a significant decrease in the rate of nitrous oxide production. Chloramphenicol also decreased (>50%) the activity of existing denitrification enzymes in pure cultures of Pseudomonas denitrificans that were harvested during log- phase growth and maintained for 2 weeks in a starvation medium lacking electron donor. Short-term time courses of nitrate consumption and nitrous oxide production in the presence of acetylene with P. denitrificans undergoing carbon starvation were performed under optimal conditions designed to mimic denitrification enzyme activity assays used with soils. Time courses were linear for both chloramphenicol and control flasks, and rate estimates for the two treatments were significantly different at the 95% confidence level. Complete or partial inhibition of existing enzyme activity is not consistent with the current understanding of the mode of action of chloramphenicol or current practice, in which the compound is frequently employed to inhibit de novo protein synthesis during the course of microbial activity assays. The results of this study demonstrate that chloramphenicol amendment can inhibit the activity of existing denitrification enzymes and suggest that caution is needed in the design and interpretation of denitrification activity assays in which chloramphenicol is used to prevent new protein synthesis.

  1. DOES ABSOLUTE SYNONYMY EXIST IN OWERE-IGBO?

    African Journals Online (AJOL)

    USER

    The researcher also interviewed native speakers of the dialect. The study ... The word 'synonymy' means sameness of meaning, i.e., a relationship in which more ... whether absolute synonymy exists in Owere–Igbo or not. ..... 'close this book'.

  2. 46 CFR 50.05-5 - Existing boilers, pressure vessels or piping systems.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 2 2010-10-01 2010-10-01 false Existing boilers, pressure vessels or piping systems. 50... ENGINEERING GENERAL PROVISIONS Application § 50.05-5 Existing boilers, pressure vessels or piping systems. (a) Whenever doubt exists as to the safety of an existing boiler, pressure vessel, or piping system, the marine...

  3. Structural Analysis of Extended Plasma Focus Chamber

    International Nuclear Information System (INIS)

    Mohd Azhar Ahmad; Abdul Halim Baijan; Siti Aiasah Hashim

    2016-01-01

    Accelerator Development Centre (ADC) of Nuclear Malaysia intends to upgrade the plasma focus device. It involves the extension part placed on top of the existing plasma focus vacuum chamber. This extended vacuum chamber purposely to give an extra space in conducting experiments on the existing plasma focus chamber. The aim of upgrading the plasma focus device is to solve the limitation in research and analysis of sample due to its done in an open system that cause analysis of samples is limited and less optimal. This extended chamber was design in considering the ease of fabrication as well as durability of its structural. Thus, this paper discusses the structural analysis in term of pressure loading effect in extended chamber. (author)

  4. Numerical simulations (2D) on the influence of pre-existing local structures and seismic source characteristics in earthquake-volcano interactions

    Science.gov (United States)

    Farías, Cristian; Galván, Boris; Miller, Stephen A.

    2017-09-01

    Earthquake triggering of hydrothermal and volcanic systems is ubiquitous, but the underlying processes driving these systems are not well-understood. We numerically investigate the influence of seismic wave interaction with volcanic systems simulated as a trapped, high-pressure fluid reservoir connected to a fluid-filled fault system in a 2-D poroelastic medium. Different orientations and earthquake magnitudes are studied to quantify dynamic and static stress, and pore pressure changes induced by a seismic event. Results show that although the response of the system is mainly dominated by characteristics of the radiated seismic waves, local structures can also play an important role on the system dynamics. The fluid reservoir affects the seismic wave front, distorts the static overpressure pattern induced by the earthquake, and concentrates the kinetic energy of the incoming wave on its boundaries. The static volumetric stress pattern inside the fault system is also affected by the local structures. Our results show that local faults play an important role in earthquake-volcanic systems dynamics by concentrating kinetic energy inside and acting as wave-guides that have a breakwater-like behavior. This generates sudden changes in pore pressure, volumetric expansion, and stress gradients. Local structures also influence the regional Coulomb yield function. Our results show that local structures affect the dynamics of volcanic and hydrothermal systems, and should be taken into account when investigating triggering of these systems from nearby or distant earthquakes.

  5. Analysis of structural diseases in widened structure due to the shrinkage and creep difference of new bridge

    Science.gov (United States)

    Wu, Wenqing; Zhang, Hui

    2018-03-01

    In order to investigate the possible structural diseases brought to the top flange of existing prestressed concrete box girder bridge due to the shrinkage and creep difference between new and old bridge, the stress state of the existing box girder before and after widening and the mechanisms of potential structural diseases were analyzed using finite element method in this paper. Results showed that the inner flange of the old box girder were generally in the state of large tensile stress, the main reason for which was the shrinkage and creep effect difference of the new and old bridge. And the tensile stress was larger than tensile strength of C50 concrete, which would most likely cause crack in the deck plate of box girder. Hence, reinforcement measures are needed to be designed carefully. Meanwhile, the transverse deformation of widened structure had exceeded the distance between the anti-seismic block and the web of box girder at the end cross section, which would squeeze anti-seismic block severely. Therefore, it is necessary to limit the length of continuous bridge in need of widening.

  6. Energy and architecture: improvement of energy performance in existing buildings

    Energy Technology Data Exchange (ETDEWEB)

    Haase, Matthias; Wycmans, Annemie; Solbraa, Anne; Grytli, Eir

    2011-07-01

    This book aims to give an overview of different aspects of retrofitting existing buildings. The target group is students of architecture and building engineering as well as building professionals. Eight out of ten buildings which we will inhabit in 2050 already exist. This means that a great potential for reducing our carbon footprint lies in the existing building stock. Students from NTNU have used the renovation of a 1950s school building at Linesoeya in Soer-Trondelag as a case to increase their awareness and knowledge about the challenges building professionals need to overcome to unite technical details and high user quality into good environmental performance. The students were invited by the building owners and initiators of LIPA Eco Project to contribute to its development: By retrofitting an existing building to passive house standards and combining this with energy generated on site, LIPA Eco Project aims to provide a hands-on example with regard to energy efficiency, architectural design and craftsmanship for a low carbon society. The overall goal for this project is to raise awareness regarding resource efficiency measures in architecture and particularly in existing building mass.(au)

  7. Results of the QUENCH-12 experiment on reflood of a VVER-type bundle

    Energy Technology Data Exchange (ETDEWEB)

    Stuckert, J.; Grosse, M.; Heck, M.; Schanz, G.; Sepold, L.; Stegmaier, U.; Steinbrueck, M. [Forschungszentrum Karlsruhe GmbH Technik und Umwelt (Germany). Inst. fuer Materialforschung, Programm Nukleare Sicherheitsforschung; Goryachev, A.; Ivanova, I. [RIAR (FSUE SSC-RIAR) Dimitrovgrad (Russian Federation)

    2008-09-15

    between 850 mm and 1050 mm exceeded the melting temperature of {beta}-Zr, i.e. 2130 K. The total hydrogen production in QUENCH-12 was 58 g (QUENCH-06: 36 g). During reflood 24 g of hydrogen were released (QUENCH-06: 4 g). Additionally to the hydrogen produced by the strong oxidation of zirconium during temperature escalation and at the beginning of the reflood phase, respectively, a large amount of hydrogen previously absorbed in the metal is assumed to be released at that time. Three corner rods were withdrawn during the experiment, one at the end of preoxidation, a second one during the transient phase and a third one after the test. All corner rods showed breakaway oxidation effects, i.e. strong spalling of oxide scales. In addition to the corner rods, the surfaces of the rod simulators and shroud show intensive breakaway oxidation although the breakaway is more pronounced at the surfaces of the corner rods. Possible reasons for the differences could be different mechanical properties of tube and massive rod and other surface preparation of cladding and corner rods. Breakaway oxidation together with local melt formation and subsequent melt oxidation as well as a longer exposure time at temperature in QUENCH-12 compared to QUENCH-06 is considered as reason for a higher hydrogen generation compared to the QUENCH-06 experiment. (orig.)

  8. Results of the QUENCH-12 experiment on reflood of a VVER-type bundle

    International Nuclear Information System (INIS)

    Stuckert, J.; Grosse, M.; Heck, M.; Schanz, G.; Sepold, L.; Stegmaier, U.; Steinbrueck, M.

    2008-09-01

    .e. 2130 K. The total hydrogen production in QUENCH-12 was 58 g (QUENCH-06: 36 g). During reflood 24 g of hydrogen were released (QUENCH-06: 4 g). Additionally to the hydrogen produced by the strong oxidation of zirconium during temperature escalation and at the beginning of the reflood phase, respectively, a large amount of hydrogen previously absorbed in the metal is assumed to be released at that time. Three corner rods were withdrawn during the experiment, one at the end of preoxidation, a second one during the transient phase and a third one after the test. All corner rods showed breakaway oxidation effects, i.e. strong spalling of oxide scales. In addition to the corner rods, the surfaces of the rod simulators and shroud show intensive breakaway oxidation although the breakaway is more pronounced at the surfaces of the corner rods. Possible reasons for the differences could be different mechanical properties of tube and massive rod and other surface preparation of cladding and corner rods. Breakaway oxidation together with local melt formation and subsequent melt oxidation as well as a longer exposure time at temperature in QUENCH-12 compared to QUENCH-06 is considered as reason for a higher hydrogen generation compared to the QUENCH-06 experiment. (orig.)

  9. 46 CFR 4.05-25 - Reports when state of war exists.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 1 2010-10-01 2010-10-01 false Reports when state of war exists. 4.05-25 Section 4.05-25 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY PROCEDURES APPLICABLE TO THE PUBLIC MARINE... war exists. During the period when a state of war exists between the United States and any foreign...

  10. Hamiltonian structure of the Lotka-Volterra equations

    Science.gov (United States)

    Nutku, Y.

    1990-03-01

    The Lotka-Volterra equations governing predator-prey relations are shown to admit Hamiltonian structure with respect to a generalized Poisson bracket. These equations provide an example of a system for which the naive criterion for the existence of Hamiltonian structure fails. We show further that there is a three-component generalization of the Lotka-Volterra equations which is a bi-Hamiltonian system.

  11. Intelligent structures and design of energy related facilities

    International Nuclear Information System (INIS)

    Namba, Haruyuki

    1994-01-01

    Possibility of applying intelligent structural concepts to civil design of energy plants is discussed. Intelligent structures, which are now common in aerospace engineering field, are also referred to as adaptive structures or smart structures depending on cases. Among various existing concepts, reconfigurable structures, precise shape control, structural monitoring using smart materials of optical fiber sensors, and relation with recent innovative communication technologies are focused from civil engineering point of view. Application of such new technologies will help to enhance design of energy related plants, which include multiplex functions which need to be very reliable and safe. (author)

  12. European networks in structural integrity

    International Nuclear Information System (INIS)

    Crutzen, S.; Davies, M.; Hemsworth, B.; Hurst, R.; Kussmaul, K.

    1994-01-01

    Several institutions and electrical utilities in Europe, including the Joint Research Centre (JRC) have the capability to deal problems posed by the operation and ageing of structural components and with their structural integrity assessment. These institutions and the JRC have developed cooperative programmes now organised in networks. They include utilities, engineering companies, R and D laboratories and Regulatory Bodies. Networks are organised and managed like the successful PISC programme: The Institute for Advanced Materials of JRC plays the role of Operating Agent and Manager of these networks: ENIQ, AMES, NESC, each of them dealing with a specific aspect of fitness for purpose of materials in structural components. There exist strong links between the networks and EC Working Groups on Structural Integrity Codes and Standards. (orig.)

  13. The structural, connectomic and network covariance of the human brain.

    Science.gov (United States)

    Irimia, Andrei; Van Horn, John D

    2013-02-01

    Though it is widely appreciated that complex structural, functional and morphological relationships exist between distinct areas of the human cerebral cortex, the extent to which such relationships coincide remains insufficiently appreciated. Here we determine the extent to which correlations between brain regions are modulated by either structural, connectomic or network-theoretic properties using a structural neuroimaging data set of magnetic resonance imaging (MRI) and diffusion tensor imaging (DTI) volumes acquired from N=110 healthy human adults. To identify the linear relationships between all available pairs of regions, we use canonical correlation analysis to test whether a statistically significant correlation exists between each pair of cortical parcels as quantified via structural, connectomic or network-theoretic measures. In addition to this, we investigate (1) how each group of canonical variables (whether structural, connectomic or network-theoretic) contributes to the overall correlation and, additionally, (2) whether each individual variable makes a significant contribution to the test of the omnibus null hypothesis according to which no correlation between regions exists across subjects. We find that, although region-to-region correlations are extensively modulated by structural and connectomic measures, there are appreciable differences in how these two groups of measures drive inter-regional correlation patterns. Additionally, our results indicate that the network-theoretic properties of the cortex are strong modulators of region-to-region covariance. Our findings are useful for understanding the structural and connectomic relationship between various parts of the brain, and can inform theoretical and computational models of cortical information processing. Published by Elsevier Inc.

  14. O discurso racional cartesiano na segunda prova da existência de Deus (The racional cartesian discourse on the second proof of God’s existence

    Directory of Open Access Journals (Sweden)

    Monica Fernandes Abreu

    2010-09-01

    Full Text Available Esta reflexão pretende mostrar o discurso racional cartesiano na segunda prova da existência de Deus. Para tanto, Descartes se depara com uma pergunta central: qual  a causa da existência da res cogitans que é finita e possui a ideia de infinito? A resposta é encontrada na desproporcionalidade ontológica entre o finito e o infinito. Essa desproporcionalidade é elucidada mediante dois conceitos: o princípio de causalidade que determina que a causa deve ser igual ou superior a coisa causada e o princípio de criação contínua em que a causa que criou o ser não é menor do que aquela que o conserva em sua existência. As objeções destacadas no texto contra os argumentos cartesianos foram escolhas deliberadas que servem para elucidar a importância da racionalidade como fundamento para a prova da existência de Deus. A relação entre o  entendimento e a liberdade, apresentada  no texto sucintamente, justifica a impossibilidade da res cogitans ser causa de si mesma.Palavras-chave:  Infinito; finito; causalidade; criação contínua AbstractThis essay aims to show the rational Cartesian discourse on the second proof of God’s existence. In order to do so, Descartes faces a core question: which is the cause for the existence of the res cogitans that is finite in front of the idea of the infinite? The answer is found in the ontological disproportionality between the finite and the infinite. This disproportionality is elucidated through a couple crucial concepts: the principle of causality, which determines that the cause must be equal or superior to the caused thing and the principle of continuous creation, in which the cause that created the being is not inferior than the one that preserves its existence. The objections highlighted in the text against the Cartesian arguments were deliberated choices, to elucidate the relevance of rationality as the foundation for the proof of God’s existence. The relation between the understanding

  15. Complexity of Curved Glass Structures

    Science.gov (United States)

    Kosić, T.; Svetel, I.; Cekić, Z.

    2017-11-01

    Despite the increasing number of research on the architectural structures of curvilinear forms and technological and practical improvement of the glass production observed over recent years, there is still a lack of comprehensive codes and standards, recommendations and experience data linked to real-life curved glass structures applications regarding design, manufacture, use, performance and economy. However, more and more complex buildings and structures with the large areas of glass envelope geometrically complex shape are built every year. The aim of the presented research is to collect data on the existing design philosophy on curved glass structure cases. The investigation includes a survey about how architects and engineers deal with different design aspects of curved glass structures with a special focus on the design and construction process, glass types and structural and fixing systems. The current paper gives a brief overview of the survey findings.

  16. International symposium on seismic evaluation of existing nuclear facilities. Book of invited and contributed papers

    International Nuclear Information System (INIS)

    2003-08-01

    In the past decade, seismic evaluation of existing Nuclear Power Plants (NPPs) has been an issue in western countries (particularly for the east of North America and for older NPPs in Europe) as well as in eastern European countries where systematic reviews of NPPs were carried out. Several Member States have still on-going seismic upgrading programmes. Presently. projects of plant life extension create an additional interest in safety evaluation of existing NPPs. Seismic evaluation is also an issue for other nuclear facilities. In western countries. some older facilities (laboratories, research reactors, fuel plants...) have been designed without taking into account (or poorly taking into account) earthquake input, even on seismic sites. In eastern countries, the situation is not yet clearly evaluated. In several countries concerns are expressed regarding research reactors. Generally speaking, the seismic evaluation of these nuclear facilities is not so advanced as the evaluation of NPPs and presents a wider range of different situations. Those safety issues raised by the seismic evaluation of existing NPPs are addressed in an IAEA Safety Report 'Seismic Evaluation of Existing Nuclear Power Plants' (2003). Other nuclear facilities are, at least partly, covered by IAEA-TECDOC 1347 'Design of Nuclear Facilities other than NPPs in Relation to External Events, with a Special Emphasis on Earthquake' (2003) that supersedes the former TECDOC 348 'Earthquake Resistant Design of Nuclear Facilities with Limited Radioactive Inventory' (1985). Concurrently with the publishing of relevant documentation, the IAEA has organized this Symposium in order to foster the exchange of information on topical issues in seismic evaluation of existing nuclear facilities, with the aim of: consolidating an international consensus on the present status of these issues; promoting a homogeneous engineering approach of their resolution; identifying the needs for strengthening international co

  17. International symposium on seismic evaluation of existing nuclear facilities. Book of invited and contributed papers

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2003-08-01

    In the past decade, seismic evaluation of existing Nuclear Power Plants (NPPs) has been an issue in western countries (particularly for the east of North America and for older NPPs in Europe) as well as in eastern European countries where systematic reviews of NPPs were carried out. Several Member States have still on-going seismic upgrading programmes. Presently. projects of plant life extension create an additional interest in safety evaluation of existing NPPs. Seismic evaluation is also an issue for other nuclear facilities. In western countries. some older facilities (laboratories, research reactors, fuel plants...) have been designed without taking into account (or poorly taking into account) earthquake input, even on seismic sites. In eastern countries, the situation is not yet clearly evaluated. In several countries concerns are expressed regarding research reactors. Generally speaking, the seismic evaluation of these nuclear facilities is not so advanced as the evaluation of NPPs and presents a wider range of different situations. Those safety issues raised by the seismic evaluation of existing NPPs are addressed in an IAEA Safety Report 'Seismic Evaluation of Existing Nuclear Power Plants' (2003). Other nuclear facilities are, at least partly, covered by IAEA-TECDOC 1347 'Design of Nuclear Facilities other than NPPs in Relation to External Events, with a Special Emphasis on Earthquake' (2003) that supersedes the former TECDOC 348 'Earthquake Resistant Design of Nuclear Facilities with Limited Radioactive Inventory' (1985). Concurrently with the publishing of relevant documentation, the IAEA has organized this Symposium in order to foster the exchange of information on topical issues in seismic evaluation of existing nuclear facilities, with the aim of: consolidating an international consensus on the present status of these issues; promoting a homogeneous engineering approach of their resolution; identifying the needs for strengthening international co

  18. Newspaper and internet display advertising: Co-existence or substitution?

    OpenAIRE

    Lindstädt, Nadine; Budzinski, Oliver

    2012-01-01

    Newspapers have been experiencing declining circulation figures and diminishing advertising revenues for several years – both effects might pose a threat to the continuing existence of (print) newspapers. In an earlier paper, Lindstädt & Budzinski (2011) argued from a theoretical viewpoint that industry-specific patterns exist that determine substitution or complementation effects between internet and newspaper advertising. It was argued that retail advertising, in particular, may offer a nic...

  19. Evaluation of the integrity of existing NFS waste tanks

    International Nuclear Information System (INIS)

    1977-12-01

    Various means of investigating the integrity of the existing NFS waste tanks are presented, including: visual inspection, ultrasonic testing, acoustic-emission monitoring, radiography, and forced-vibration testing. The experience that exists in performing such investigations of high-level radioactive waste tanks is documented, including: visual inspections, photography, wall-thickness measurements, and forced-vibration testing. An evaluation is made on the relative merits of the presented inspection and testing alternatives

  20. Image Analysis Technique for Material Behavior Evaluation in Civil Structures

    Science.gov (United States)

    Moretti, Michele; Rossi, Gianluca

    2017-01-01

    The article presents a hybrid monitoring technique for the measurement of the deformation field. The goal is to obtain information about crack propagation in existing structures, for the purpose of monitoring their state of health. The measurement technique is based on the capture and analysis of a digital image set. Special markers were used on the surface of the structures that can be removed without damaging existing structures as the historical masonry. The digital image analysis was done using software specifically designed in Matlab to follow the tracking of the markers and determine the evolution of the deformation state. The method can be used in any type of structure but is particularly suitable when it is necessary not to damage the surface of structures. A series of experiments carried out on masonry walls of the Oliverian Museum (Pesaro, Italy) and Palazzo Silvi (Perugia, Italy) have allowed the validation of the procedure elaborated by comparing the results with those derived from traditional measuring techniques. PMID:28773129